WorldWideScience

Sample records for bwr reactors integridad

  1. Structural integrity and management of aging in internal components of BWR reactors; Integridad estructural y manejo del envejecimiento en componentes internos de reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Arganis J, C.R. [Instituto Nacional de Investigaciones Nucleares, Km 36.5 Carretera Mexico, Toluca Salazar Edo. de Mexico (Mexico)]. E-mail: craj@nuclear.inin.mx

    2004-07-01

    Presently work the bases to apply structural integrity and the handling of the aging of internal components of the pressure vessel of boiling water reactors of water are revised and is carried out an example of structural integrity in the horizontal welding H4 of the encircling one of the core of a reactor, taking data reported in the literature. It is also revised what is required to carry out the handling program or conduct of the aging (AMP). (Author)

  2. Power oscillations in BWR reactors; Oscilaciones de potencia en reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa P, G. [Division de Ciencias Basicas e Ingenieria, Universidad Autonoma Metropolitana-Iztapalapa, 09340 Mexico D.F. (Mexico)]. E-mail: gepe@xanum.uam.mx

    2002-07-01

    One of the main problems in the operation of BWR type reactors is the instability in power that these could present. One type of oscillations and that is the objective of this work is the named density wave, which is attributed to the thermohydraulic processes that take place in the reactor core. From the beginnings of the development of BWR reactors, the stability of these has been an important aspect in their design, due to its possible consequences on the fuel integrity. The reactor core operates in two phase flow conditions and it is observed that under certain power and flow conditions, power instabilities appear. Studying this type of phenomena is complex, due to that a reactor core is constituted approximately by 27,000 fuel bars with different distributions of power and flow. The phenomena that cause the instability in BWR reactors continue being matter of scientific study. In the literature mainly in nuclear subject, it can be observed that exist different methods and approximations for studying this type of phenomena, nevertheless, their results are focused to establish safety limits in the reactor operation, instead of studying in depth of the knowledge about. Also in this line sense of the reactor data analysis, the oscillations characteristic frequencies are obtained for trying to establish if the power is growing or decreasing. In addition to that before mentioned in this paper it is presented a rigorous study applying the volumetric average method, for obtaining the vacuum waves propagation velocities and its possible connection with the power oscillations. (Author)

  3. Reactor core stability monitoring method for BWR type reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kanemoto, Shigeru; Ebata, Shigeo.

    1992-09-01

    In an operation for a BWR type reactor, reactor power is usually increased or decreased by controlling both of control rods and reactor core flow rate. Under a certain condition, the reactor core is made unstable by the coupling of nuclear and thermohydrodynamic characteristics in the reactor. Therefore, the reactor power and the reactor core flow rate are changed within a range predetermined by a design calculation. However, if reactor core stability can be always measured and monitored, it is useful for safe operation, as well as an existent operation range can be extended to enable more effective operation. That is, autoregressive a coefficient is determined successively on real time based on fluctuation components of neutron flux signals. Based on the result, an amplification ratio, as a typical measure of the reactor core stability, is determined on a real time. A time constant of the successive calculation for the autoregressive coefficient can be made variable by the amplification ratio. Then, the amplification ratio is estimated at a constant accuracy. With such procedures, the reactor core stability can be monitored successively in an ON-line manner at a high accuracy, thereby enabling to improve the operation performance. (I.S.).

  4. Neutron dosimetry. Environmental monitoring in a BWR type reactor; Dosimetria de neutrones. Monitoreo ambiental en un reactor del tipo BWR

    Energy Technology Data Exchange (ETDEWEB)

    Tavera D, L.; Camacho L, M.E

    1991-01-15

    The measurements carried out on reactor dosimetry are applied mainly to the study on the effects of the radiation in 108 materials of the reactor; little is on the environmental dosimetry outside of the primary container of BWR reactors. In this work the application of a neutron spectrometer formed by plastic detectors of nuclear traces manufactured in the ININ, for the environmental monitoring in penetrations around the primary container of the unit I of the Laguna Verde central is presented. The neutron monitoring carries out with purposes of radiological protection, during the operational tests of the reactor. (Author)

  5. Studies of fragileness in steels of vessels of BWR reactors; Estudios de fragilizacion en aceros de vasija de reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Robles, E.F.; Balcazar, M.; Alpizar, A.M.; Calderon, B.E. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2003-07-01

    The structural materials with those that are manufactured the pressure vessels of the BWR reactors, suffer degradation in its mechanical properties mainly to the damage taken place by the fast neutrons (E > 1 MeV) coming from the reactor core. Its are experimentally studied those mechanisms of neutron damage in this material type, by means of the irradiation of steel vessel in experimental reactors to age them quickly. Alternatively it is simulated the neutron damage by means of irradiation of steel with heavy ions. In this work those are shown first results of the damage induced by irradiation from a similar steel to the vessel of a BWR reactor. The irradiation was carried out with fast neutrons (E > 1 MeV, fluence of 1.45 x 10{sup 18} n/cm{sup 2}) in the TRIGA MARK lll reactor and separately with Ni{sup +3} ions in a Tandetrom accelerator, E = 4.8 MeV and range of the ionic flow of 0.1 to 53 iones/A{sup 2}. (Author)

  6. Identification of the reduced order models of a BWR reactor; Identificacion de modelos de orden reducido de un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez S, A. [UNAM, Laboratorio de Analisis de Ingenieria de Reactores Nucleares, DEPFI, Campus Morelos, en IMTA Jiutepec, Morelos (Mexico)]. e-mail: augusto@correo.unam.mx

    2004-07-01

    The present work has as objective to analyze the relative stability of a BWR type reactor. It is analyzed that so adaptive it turns out to identify the parameters of a model of reduced order so that this it reproduces a condition of given uncertainty. This will take of a real fact happened in the La Salle plant under certain operation conditions of power and flow of coolant. The parametric identification is carried out by means of an algorithm of recursive least square and an Output Error model (Output Error), measuring the output power of the reactor when the instability is present, and considering that it is produced by a change in the reactivity of the system in the same way that a sign of type step. Also it is carried out an analytic comparison of the relative stability, analyzing two types of answers: the original answer of the uncertainty of the reactor vs. the obtained response identifying the parameters of the model of reduced order, reaching the conclusion that it is very viable to adapt a model of reduced order to study the stability of a reactor, under the only condition to consider that the dynamics of the reactivity is of step type. (Author)

  7. Design of a redundant meteorological station for a BWR reactor; Diseno de una estacion meteorologica redundante para un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez S, R.; Celis del Angel, L.; Bucio, F.; Rivero, T.; Palacios, J. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)]. e-mail: ramses@nuclear.inin.mx

    2008-07-01

    In this work the design of a meteorological station for a reactor type BWR is proposed. Two independent channels of data acquisition that allow him to have a bigger readiness is exposed. It is incorporate sensors without mobile parts to measure speed, wind direction and pluvial precipitation. It also counts, with sensors of global solar radiation, net radiation, barometric pressure, relative humidity and ambient temperature; with them they are possible to be calculated, moreover, other variables as temperature differential, dew point and atmospheric stability. The sensors are placed on a tower to different heights and send their information (each second) to a local registration system, the one which in turn, it remits the data to the monitoring office so that a computer is linked with the system, display and management the information in real time and automatic way. The redundant structure allows that in the event of maintenance the data acquisition is not interrupted, even if the information is transferred to another place. In all the station sections it is used protocols of standard communication to allow that a great quantity of devices can be connected without major problem. The above-mentioned would allow to the operators in the control room to have reliable information during the whole time of the reactor operation. (Author)

  8. Applied methods for mitigation of damage by stress corrosion in BWR type reactors; Metodos aplicados para la mitigacion del dano por corrosion bajo esfuerzo en reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez C, R.; Diaz S, A.; Gachuz M, M.; Arganis J, C. [Instituto Nacional de Investigaciones Nucleares, Gerencia de Ciencia de Materiales, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1998-07-01

    The Boiling Water nuclear Reactors (BWR) have presented stress corrosion problems, mainly in components and pipes of the primary system, provoking negative impacts in the performance of energy generator plants, as well as the increasing in the radiation exposure to personnel involucred. This problem has caused development of research programs, which are guided to find solution alternatives for the phenomena control. Among results of greater relevance the control for the reactor water chemistry stands out particularly in the impurities concentration and oxidation of radiolysis products; as well as the supervision in the materials selection and the stresses levels reduction. The present work presents the methods which can be applied to diminish the problems of stress corrosion in BWR reactors. (Author)

  9. Design and axial optimization of nuclear fuel for BWR reactors; Diseno y optimizacion axial de combustible nuclear para reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Garcia V, M.A

    2006-07-01

    In the present thesis, the modifications made to the axial optimization system based on Tabu Search (BT) for the axial design of BWR fuel type are presented, developed previously in the Nuclear Engineering Group of the UNAM Engineering Faculty. With the modifications what is mainly looked is to consider the particular characteristics of the mechanical design of the GE12 fuel type, used at the moment in the Laguna Verde Nucleo electric Central (CNLV) and that it considers the fuel bars of partial longitude. The information obtained in this thesis will allow to plan nuclear fuel reloads with the best conditions to operate in a certain cycle guaranteeing a better yield and use in the fuel burnt, additionally people in charge in the reload planning will be favored with the changes carried out to the system for the design and axial optimization of nuclear fuel, which facilitate their handling and it reduces their execution time. This thesis this developed in five chapters that are understood in the following way in general: Chapter 1: It approaches the basic concepts of the nuclear energy, it describes the physical and chemical composition of the atoms as well as that of the uranium isotopes, the handling of the uranium isotope by means of the nuclear fission until arriving to the operation of the nuclear reactors. Chapter 2: The nuclear fuel cycle is described, the methods for its extraction, its conversion and its enrichment to arrive to the stages of the nuclear fuel management used in the reactors are described. Beginning by the radial design, the axial design and the core design of the nuclear reactor related with the fuel assemblies design. Chapter 3: the optimization methods of nuclear fuel previously used are exposed among those that are: the genetic algorithms method, the search methods based on heuristic rules and the application of the tabu search method, which was used for the development of this thesis. Chapter 4: In this part the used methodology to the

  10. Propagation of cracks by stress corrosion in conditions of BWR type reactor; Propagacion de grietas por corrosion bajo esfuerzo en condiciones de reactor de agua en ebullicion (BWR)

    Energy Technology Data Exchange (ETDEWEB)

    Merino C, F.J. [ININ, 52045 Estado de Mexico (Mexico); Fuentes C, P. [ITT, Metepec, Estado de Mexico (Mexico)]. E-mail: fjmc@nuclear.inin.mx

    2004-07-01

    In this work, the obtained results when applying the Hydrogen Chemistry to a test tube type Compact Tension (CT), built in austenitic stainless steel 304l, simulating the conditions to those that it operates a Boiling Water Reactor (BWR), temperature 288 C and pressure of 8 MPa are presented. With the application of this water chemistry, seeks to be proven the diminution of the crack propagation speed. (Author)

  11. Damage by radiation in structural materials of BWR reactor vessels; Dano por radiacion en materiales estructurales de vasijas de reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Robles, E.; Balcazar, M.; Alpizar, A.M.; Calderon, B.E. [Departamento de Sintesis y Caracterizacion de Materiales, Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    2002-07-01

    The structural materials which are manufactured the pressure vessels of the BWR reactors undergo degradation in their mechanical properties mainly due to the damage produced by the fast neutrons (E> 1 MeV) coming from the reactor core. The mechanisms of neutron damage in this type of materials are experimentally studied, through the irradiation of vessel steel in experimental reactors for a quickly ageing. Alternately the neutron damage through steel irradiation with heavy ions is simulated. In this work the first results of the damage induced by irradiation of a similar steel to the vessel of a BWR reactor are shown. The irradiation was performed with fast neutrons (E> 1 MeV, fluence of 1.45 x 10{sup 18} n/cm{sup 2}) in the TRIGA Mark III Salazar reactor and separately with Ni{sup +3} ions in a Tandetrom accelerator (E= 4.8 MeV and an ion flux rank of 0.1 to 53 ions/A{sup 2}). (Author)

  12. Study on reactor vessel replacement (RVR) for 1100 MW class BWR plants in Japan

    Energy Technology Data Exchange (ETDEWEB)

    Mizutani, J.; Kawamura, S. [Tokyo Electric Power Co., Inc. (Japan); Aoki, M. [Hitachi Ltd., Ibaraki (Japan); Mori, T. [Toshiba Corp., Yokihama (Japan)

    2001-07-01

    Plant Life Management (PLM) is being studied in Japan, and reactor vessel replacement (RVR) is being considered as one option. Since reactor internals, except for reusable parts, and the reactor pressure vessel (RPV) are replaced, the RVR provides an effective technology for extending the service life of nuclear power plants substantially. At ICONE 7, we reported on the technical viability of the RVR for BWR4-type 800 MWe class plants. This time, we rationalized the RVR method through a study for BWR5-type 1100 MWe class plants to reduce the RVR duration and evaluated the technical viability and the economic efficiency of the method. In addition, we discuss how to dispose of the RPV to complete a scenario of the process from the RVR to its final disposal. (author)

  13. Thermal hydraulics characterization of the core and the reactor vessel type BWR; Caracterizacion termohidraulica del nucleo y de la vasija de un reactor tipo BWR

    Energy Technology Data Exchange (ETDEWEB)

    Zapata Y, M.; Lopez H, L.E. [CFE, Carretera Cardel-Nautla Km. 42.5, Municipio Alto Lucero, Veracruz (Mexico)]. e-mail: marxlenin.zapata@cfe.gob.mx

    2008-07-01

    The thermal hydraulics design of a reactor type BWR 5 as the employees in the nuclear power plant of Laguna Verde involves the coupling of at least six control volumes: Pumps jet region, Stratification region, Core region, Vapor dryer region, Humidity separator region and Reactor region. Except by the regions of the core and reactor, these control volumes only are used for design considerations and their importance as operative data source is limited. It is for that is fundamental to complement the thermal hydraulics relations to obtain major data that allow to determine the efficiency of internal components, such as pumps jet, humidity separator and vapor dryer. Like example of the previous thing, calculations are realized on the humidity of the principal vapor during starting, comparing it with the values at the moment incorporated in the data banks of the computers of process of both units. (Author)

  14. Impact of Reactor Operating Parameters on Cask Reactivity in BWR Burnup Credit

    Energy Technology Data Exchange (ETDEWEB)

    Ilas, Germina [ORNL; Betzler, Benjamin R [ORNL; Ade, Brian J [ORNL

    2017-01-01

    This paper discusses the effect of reactor operating parameters used in fuel depletion calculations on spent fuel cask reactivity, with relevance for boiling-water reactor (BWR) burnup credit (BUC) applications. Assessments that used generic BWR fuel assembly and spent fuel cask configurations are presented. The considered operating parameters, which were independently varied in the depletion simulations for the assembly, included fuel temperature, bypass water density, specific power, and operating history. Different operating history scenarios were considered for the assembly depletion to determine the effect of relative power distribution during the irradiation cycles, as well as the downtime between cycles. Depletion, decay, and criticality simulations were performed using computer codes and associated nuclear data within the SCALE code system. Results quantifying the dependence of cask reactivity on the assembly depletion parameters are presented herein.

  15. Current understanding on the neutron irradiation embrittlement of BWR reactor pressure vessel steels in Japan

    Energy Technology Data Exchange (ETDEWEB)

    Asano, K.; Nishiyama, T. [TEPCO (Japan); Soneda, N.; Dohi, K.; Nishida, K.; Nomoto, A. [CRIEPI (Japan); Ohta, T. [Japan Atomic Power Co. (Japan); Ishimaru, Y. [Chugoku EPCO (Japan); Yoneda, H. [Hokuriku EPCO (Japan); Lida, J. [Tohoku EPCO (Japan); Yuya, H. [Chubu EPCO (Japan)

    2011-07-01

    Neutron irradiation embrittlement of reactor pressure vessel (RPV) steels has been of concern primarily for the pressurized water reactors (PWRs). After long operation experiences, we are now becoming aware of the situation that the neutron irradiation embrittlement is also of concern for some of the boiling water reactors (BWRs) particularly with Cu-containing RPV steels. The surveillance data of Cu-containing BWR RPV steels show relatively larger shift in ductile-to-brittle transition temperature of fracture toughness than predicted by the embrittlement correlation method developed in late eighties and early nineties. Accurate evaluation of the amount of embrittlement is now very important for long-term operation of BWRs. In this paper, we will describe the neutron irradiation embrittlement of BWR RPVs in Japan. Some of the materials that show relatively large transition temperature shifts are investigated to understand the causes of embrittlement using state-of-the-art microstructural characterization techniques. Furthermore, some archive materials of such RPVs are irradiated in a material testing reactor with high neutron flux to understand the effect of flux on transition temperature shifts and corresponding microstructural changes. Microstructural evolution under irradiation, solute clustering in particular could explain the differences in transition temperature shift of the analyzed specimens. Larger BWR RPVs, which have larger water gaps, receive less neutron irradiation and harmful impurities in steels such as copper are well controlled since 1980 so irradiation embrittlement in BWR vessels can now be considered a concern only in old and small plants. All the new information obtained through these activities was considered in the development of new embrittlement correlation that is now adopted in JEAC 4201- 2007 of Japan Electric Association

  16. Artificial intelligence applied to fuel management in BWR type reactors; Inteligencia artificial aplicada a la administracion de combustible en reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz S, J.J

    1998-10-01

    In this work two techniques of artificial intelligence, neural networks and genetic algorithms were applied to a practical problem of nuclear fuel management; the determination of the optimal fuel reload for a BWR type reactor. This is an important problem in the design of the operation cycle of the reactor. As a result of the application of these techniques, comparable or even better reloads proposals than those given by expert companies in the subject were obtained. Additionally, two other simpler problems in reactor physics were solved: the determination of the axial power profile and the prediction of the value of some variables of interest at the end of the operation cycle of the reactor. Neural networks and genetic algorithms have been applied to solve many problems of engineering because of their versatility but they have been rarely used in the area of fuel management. The results obtained in this thesis indicates the convenience of undertaking further work on this area and suggest the application of these techniques of artificial intelligence to the solution of other problems in nuclear reactor physics. (Author)

  17. Analysis of assemblies exchange in the core of a reactor BWR; Analisis del intercambio de ensambles en el nucleo de un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Kauil U, J. S. [Universidad Autonoma de Yucatan, Facultad de Ingenieria, Av. Industrias no contaminantes por Anillo Periferico Norte s/n, Apdo. Postal 150 Cordemex, Merida, Yucatan (Mexico); Fuentes M, L.; Castillo M, J. A.; Ortiz S, J. J.; Perusquia del Cueto, R., E-mail: san_dino@hotmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2012-10-15

    The performance of the core of a boiling water reactor (BWR) was evaluated when two assemblies are exchanged during the fuel reload in erroneous way. All with the purpose of analyzing the value of the neutrons effective multiplication factor and the thermal limits for an exchange of assemblies. In their realization the mentioned study was based in a transition cycle of the Unit 1 of the nuclear power plant of Laguna Verde. The obtained results demonstrate that when carrying out an exchange between two fuel assemblies in erroneous way, with regard to the original reload, the changes in the neutrons effective multiplication factor do not present a serious problem, unless the exchange has been carried out among a very burnt assembly with one fresh, where this last is taken to the periphery. (Author)

  18. Analysis CFD for the hydrogen transport in the primary containment of a BWR; Analisis CFD para el transporte de hidrogeno en la contencion primaria de un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez P, D. A.; Del Valle G, E. [IPN, Escuela Superior de Fisica y Matematicas, Av. IPN s/n, Edificio 9, Col. San Pedro Zacatenco, 07738 Mexico D. F. (Mexico); Gomez T, A. M., E-mail: guerreroazteca_69@hotmail.com [ININ, Departamento de Sistemas Nucleares, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2014-10-15

    This study presents a qualitative and quantitative comparison among the CFD GASFLOW and OpenFOAM codes which are related with the phenomenon of hydrogen transport and other gases in the primary containment of a Boiling Water Reactor (BWR). GASFLOW is a commercial license code that is well validated and that was developed in Germany for the analysis of the gases transport in containments of nuclear reactors. On the other hand, OpenFOAM is an open source code that offers several evaluation solvers for different types of phenomena; in this case, the solver reacting-Foam is used to analyze the hydrogen transport inside the primary containment of the BWR. The results that offer the solver reacting-Foam of OpenFOAM are evaluated in the hydrogen transport calculation and the results are compared with those of the program of commercial license GASFLOW to see if is viable the use of the open source code in the case of the hydrogen transport in the primary containment of a BWR. Of the obtained results so much quantitative as qualitative some differences were identified between both codes, the differences (with a percentage of maximum error of 4%) in the quantitative results are small and they are considered acceptable for this analysis type, also, these differences are attributed mainly to the used transport models, considering that OpenFOAM uses a homogeneous model and GASFLOW uses a heterogeneous model. (Author)

  19. Spent fuel data base: commercial light water reactors. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    Hauf, M.J.; Kniazewycz, B.G.

    1979-12-01

    As a consequence of this country's non-proliferation policy, the reprocessing of spent nuclear fuel has been delayed indefinitely. This has resulted in spent light water reactor (LWR) fuel being considered as a potential waste form for disposal. Since the Nuclear Regulatory Commission (NRC) is currently developing methodologies for use in the regulation of the management and disposal of high-level and transuranic wastes, a comprehensive data base describing LWR fuel technology must be compiled. This document provides that technology baseline and, as such, will support the development of those evaluation standards and criteria applicable to spent nuclear fuel.

  20. Prediction of the stability of BWR reactors during the start-up process; Prediccion de la estabilidad de reactores BWR durante el proceso de arranque

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz E, J.A.; Castillo D, R. [ININ, Km. 36.5 Carretera Mexico-Toluca, 52045 Salazar, Estado de Mexico (Mexico); Blazquez M, J.B. [Centro de Investigaciones Energetics, Medioambientales y Tecnologicas, Av Complutense 22, 28040 Madrid (Spain)

    2004-07-01

    The Boiling Water Reactors (BWR) are susceptible of uncertainties of power when they are operated to low flows of coolant (W) and high powers (P), being presented this situation mainly in the start-up process. The start-up process could be made but sure if the operator knew the value of the stability index Decay reason (Dr) before going up power and therefore to guarantee the stability. The power and the flow are constantly measures, the index Dr could also be considered its value in real time. The index Dr depends on the power, flow and many other values, such as, the distribution of the flow axial and radial neutronic, the temperature of the feeding water, the fraction of holes and other thermohydraulic and nuclear parameters. A simple relationship of Dr is derived leaving of the pattern reduced of March-Leuba, where three independent variables are had that are the power, the flow and a parameter that it contains the rest of the phenomenology, that is to say all the other quantities that affect the value of Dr. This relationship developed work presently and verified its prediction with data of start-up of commercial reactors could be used for the design of a practical procedure practice of start-up, what would support to the operator to prevent this type of events of uncertainty. (Author)

  1. Development of a methodology of analysis of instabilities in BWR reactors; Desarrollo de una metodologia de analisis de inestabilidades en reactores PWR

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Fenoll, M.; Abarca, A.; Barrachina, T.; Miro, R.; Verdu, G.

    2012-07-01

    This paper presents a methodology of analysis of the reactors instabilities of BWR type. This methodology covers of modal analysis of the point operation techniques of signal analysis and simulation of transients, through 3D Coupled RELAP5/PARCSv2.7 code.

  2. Cracks propagation by stress corrosion cracking in conditions of Boiling Water Reactor (BWR); Propagacion de grietas por corrosion bajo esfuerzo en condiciones de reactor de agua hirviente (BWR)

    Energy Technology Data Exchange (ETDEWEB)

    Fuentes C, P

    2003-07-01

    This work presents the results of the assays carried out in the Laboratory of Hot Cells of the National Institute of Nuclear Research (ININ) to a type test tube Compact Tension (CT), built in steel austenitic stainless type 304L, simulating those conditions those that it operates a Boiling Water Reactor (BWR), at temperature 288 C and pressure of 8 MPa, to determine the speed to which the cracks spread in this material that is of the one that different components of a reactor are made, among those that it highlights the reactor core vessel. The application of the Hydrogen Chemistry of the Water is presented (HWC) that is one alternative to diminish the corrosion effect low stress in the component, this is gets controlling the quantity of oxygen and of hydrogen as well as the conductivity of the water. The rehearsal is made following the principles of the Mechanics of Elastic Lineal Fracture (LEFM) that considers a crack of defined size with little plastic deformation in the tip of this; the measurement of crack advance is continued with the technique of potential drop of direct current of alternating signal, this is contained inside the standard Astm E-647 (Method of Test Standard for the Measurement of Speed of Growth of Crack by fatigue) that is the one that indicates us as carrying out this test. The specifications that should complete the test tubes that are rehearsed as for their dimensions, it forms, finish and determination of mechanical properties (tenacity to the fracture mainly) they are contained inside the norm Astm E-399, the one which it is also based on the principles of the fracture mechanics. The obtained results were part of a database to be compared with those of other rehearsals under different conditions, Normal Chemistry of the Water (NWC) and it dilutes with high content of O{sub 2}; to determine the conditions that slow more the phenomena of stress corrosion cracking, as well as the effectiveness of the used chemistry and of the method of

  3. Evaluation of the cracking by stress corrosion in nuclear reactor environments type BWR; Evaluacion del agrietamiento por corrosion bajo esfuerzo en ambientes de reactores nucleares tipo BWR

    Energy Technology Data Exchange (ETDEWEB)

    Arganis J, C. R.

    2010-07-01

    The stress corrosion cracking susceptibility was studied in sensitized, solution annealed 304 steel, and in 304-L welded with a heat treatment that simulated the radiation induced segregation, by the slow strain rate test technique, in a similar environment of a boiling water reactor (BWR), 288 C, 8 MPa, low conductivity and a electrochemical corrosion potential near 200 mV. vs. standard hydrogen electrode (She). The electrochemical noise technique was used for the detection of the initiation and propagation of the cracking. The steels were characterized by metallographic studies with optical and scanning electronic microscopy and by the electrochemical potentiodynamic reactivation of single loop and double loop. In all the cases, the steels present delta ferrite. The slow strain rate tests showed that the 304 steel in the solution annealed condition is susceptible to transgranular stress corrosion cracking (TGSCC), such as in a normalized condition showed granulated. In the sensitized condition the steel showed intergranular stress corrosion cracking, followed by a transition to TGSCC. The electrochemical noise time series showed that is possible associated different time sequences to different modes of cracking and that is possible detect sequentially cracking events, it is means, one after other, supported by the fractographic studies by scanning electron microscopy. The parameter that can distinguish between the different modes of cracking is the re passivation rate, obtained by the current decay rate -n- in the current transients. This is due that the re passivation rate is a function of the microstructure and the sensitization. Other statistic parameters like the localized index, Kurtosis, Skew, produce results that are related with mixed corrosion. (Author)

  4. Comparative analysis of results between CASMO, MCNP and Serpent for a suite of Benchmark problems on BWR reactors; Analisis comparativo de resultados entre CASMO, MCNP y SERPENT para una suite de problemas Benchmark en reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Xolocostli M, J. V.; Vargas E, S.; Gomez T, A. M. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Reyes F, M. del C.; Del Valle G, E., E-mail: vicente.xolocostli@inin.gob.mx [IPN, Escuela Superior de Fisica y Matematicas, UP - Adolfo Lopez Mateos, Edif. 9, 07738 Mexico D. F. (Mexico)

    2014-10-15

    In this paper a comparison is made in analyzing the suite of Benchmark problems for reactors type BWR between CASMO-4, MCNP6 and Serpent code. The Benchmark problem consists of two different geometries: a fuel cell of a pin and assembly type BWR. To facilitate the study of reactors physics in the fuel pin their nuclear characteristics are provided to detail, such as burnt dependence, the reactivity of selected nuclide, etc. With respect to the fuel assembly, the presented results are regarding to infinite multiplication factor for burning different steps and different vacuum conditions. Making the analysis of this set of Benchmark problems provides comprehensive test problems for the next fuels generation of BWR reactors with high extended burned. It is important to note that when making this comparison the purpose is to validate the methodologies used in modeling for different operating conditions, if the case is of other BWR assembly. The results will be within a range with some uncertainty, considering that does not depend on code that is used. Escuela Superior de Fisica y Matematicas of Instituto Politecnico Nacional (IPN (Mexico) has accumulated some experience in using Serpent, due to the potential of this code over other commercial codes such as CASMO and MCNP. The obtained results for the infinite multiplication factor are encouraging and motivate the studies to continue with the generation of the X S of a core to a next step a respective nuclear data library is constructed and this can be used by codes developed as part of the development project of the Mexican Analysis Platform of Nuclear Reactors AZTLAN. (Author)

  5. Development of the radiation models of a BWR type reactor and it facility in the SUN-RAH; Desarrollo de modelos de radiacion de un reactor tipo BWR y su instalacion en el SUN-RAH

    Energy Technology Data Exchange (ETDEWEB)

    Barron A, I. [Facultad de Ingenieria, UNAM, 04510 Mexico D.F. (Mexico)]. e-mail: isbarron@yahoo.com.mx

    2005-07-01

    This work about generation models, transport in processes and radioactive contamination of areas of a BWR central, is an amplification to the project developed in the UNAM to have a support tool in subjects or electric generation courses. It is planned about the implementation of models of radiation generation in a BWR type reactor for complement the functions developed in the University Simulator of Nucleo electric- Boiling water reactor (SUN-RAH) which it has been implemented in Simulink of MatLab and it has a model for the dynamics of one nucleo electric central that presents the main characteristics of the reactor vessel, the recirculation system, steam lines, turbines, generator, condensers and feeding water, defined by the main processes that intervene in the generation of energy of these plants. By this way the radiation monitoring systems for area and process, operate simultaneously with the processes of energy generation, with that is possible to observe the changes that present with respect to the operation conditions of the plant, and likewise to appreciate the radiation transport process through the components of the reactor, steam lines and turbines, for different operation conditions and possible faults that they could be presented during the reactor operation. (Author)

  6. Design of a mixed recharge with MOX assemblies of greater relation of moderation for a BWR reactor; Diseno de una recarga mixta con ensambles MOX de mayor relacion de moderacion para un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez S, J.R.; Alonso V, G.; Palacios H, J. [ININ, Carretera Mexico-Toluca Km. 36.5, 52045 Estado de Mexico (Mexico)]. e-mail: jrrs@nuclear.inin.mx

    2004-07-01

    The study of the fuel of mixed oxides of uranium and plutonium (MOX) it has been topic of investigation in many countries of the world and those are even discussed in many places the benefits of reprocessing the spent fuel to extract the plutonium created during the irradiation of the fuel in the nuclear power reactors. At the moment those reactors that have been loaded partially with MOX fuel, are mainly of the type PWR where a mature technology has been achieved in some countries like they are France, Belgium and England, however the experience with reactors of the type BWR is more limited and it is continued studying the best way to introduce this type of fuel in BWRs, one of the main problems to introduce MOX in reactors BWR is the neutronic design of the same one, existing different concepts to introduce the plutonium in the assemblies of fuel and one of them is the one of increasing the relationship of moderation of the assemble. In this work a MOX fuel assemble design is presented and the obtained results so far in the ININ. These results indicate that the investigated concept has some exploitable advantages in the use of the MOX fuel. (Author)

  7. Simulation of the flow obstruction of a jet pump in a BWR reactor with the code RELAP/SCDAPSIM; Simulacion de la obstruccion de flujo de una bomba jet en un reactor BWR con el codigo RELAP/SCDAPSIM

    Energy Technology Data Exchange (ETDEWEB)

    Cardenas V, J.; Filio L, C., E-mail: jaime.cardenas@cnsns.gob.mx [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Jose M. Barragan 779, Col. Narvarte, 03020 Ciudad de Mexico (Mexico)

    2016-09-15

    This work simulates the flow obstruction of a jet pump in one of the recirculation loops of a nuclear power plant with a reactor of type BWR at 100% of operating power, in order to analyze the behavior of the total flow of the refrigerant passing through the reactor core, the total flow in each recirculation loop of the reactor, together with the 10 jet pumps of each loop. The behavior of the power and the reactivity insertion due to the change of the refrigerant flow pattern is also analyzed. The simulation was carried out using the RELAP/SCDAPSIM version 3.5 code, using a reactor model with 10 jet pumps in each recirculation loop and a core consisting of 6 radial zones and 25 axial zones. The scenario postulates the flow obstruction in a jet pump in a recirculation loop A when the reactor operates at 100% rated power, causing a change in the total flow of refrigerant in the reactor core, leading to a decrease in power. Once the reactor conditions are established to its new power, the operator tries to recover the nominal power using the flow control valve of the recirculation loop A, opening stepwise as a strategy to safely recover the reactor power. In this analysis is assumed that the intention of the nuclear plant operator is to maintain the operation of the reactor during the established cycle. (Author)

  8. Evaluation of the radial design of fuel cells in an operation cycle of a BWR reactor; Evaluacion del diseno radial de celdas de combustible en un ciclo de operacion de un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez C, J.; Martin del Campo M, C. [Laboratorio de Analisis en Ingenieria de Reactores Nucleares, Facultad de Ingenieria, UNAM, Paseo Cuauhnahuac 8532, Jiutepec, Morelos (Mexico)]. e-mail: jgco@ver.megared.net.mx

    2003-07-01

    This work is continuation of one previous in the one that the application of the optimization technique called Tabu search to the radial design of fuel cells of boiling water reactors (BWR, Boiling Water Reactor) is presented. The objective function used in the optimization process only include neutron parameters (k-infinite and peak of radial power) considering the cell at infinite media. It was obtained to reduce the cell average enrichment completing the characteristics of reactivity of an original cell. The objective of the present work is to validate the objective function that was used for the radial design of the fuel cell (test cell), analyzing the operation of a one cycle of the reactor in which fuels have been fresh recharged that contain an axial area with the nuclear database of the cell designed instead of the original cell. For it is simulated it with Cm-Presto the cycle 10 of the reactor operation of the Unit 1 of the Nuclear Power station of Laguna Verde (U1-CNLV). For the cycle evaluation its were applied so much the simulation with the Haling strategy, as the simulation of the one cycle with control rod patterns and they were evaluated the energy generation and several power limits and reactivity that are used as design parameters in fuel reloads of BWR reactors. The results at level of an operation cycle of the reactor, show that the objective function used in the optimization and radial design of the cell is adequate and that it can induce to one good use of the fuel. (Author)

  9. Connected analysis nuclear-thermo-hydraulic of parallel channels of a BWR reactor using distributed computation; Analisis acoplado nuclear-termohidraulico de canales paralelos de un reactor BWR empleando computacion distribuida

    Energy Technology Data Exchange (ETDEWEB)

    Campos Gonzalez, Rina Margarita

    2007-07-15

    This work consists of the integration of three models previously developed which are described widely in Literature: model of the thermo-hydraulic channel, model of the modal neutronic and the model of the recirculation bows. The tool used for this connection of models is the PVM system, Parallel Virtual Machine that allowed paralleling the model by means of the concept of distributed computation. The purpose of making this connection of models is the one of obtaining a more complete tool than better represents the real configuration and the phenomenology of the nucleus of a BWR reactor, thus obtaining better results. In addition to maintaining the flexibility to improve the resulting model at any time, since the very complex or sophisticated models are difficult to improve being impossible to modify the equations they use and can include variables that are not of primary importance in the tackled problem or that mask relations among variables due to the excess of results. Also maintaining the flexibility for adding component of models or systems of the BWR reactor, all of this following the modeling needs. The Swedish Ringhals power plant was chosen to characterize the resulting connected model for counting on a Stability Benchmark that offers the opportunity to count on real plant data. Besides that in case 9 of cycle 14 of this Benchamark oscillations outside phase appeared, which are from great interest because the detection systems that register the average of the power of the nucleus do not detect them. Additionally in this work the model of the recirculation bows as an independent module is obtained in an individual way, since this model belongs to another work and works connected to the reactor vessel. The model of the recirculation bows is able to model several transients of interest, as it is shown in the Appendix A of this work, among which are found the tripping of recirculation pumps or the transference at low or high velocity of them. The scope of the

  10. Deposition characteristics of iodine from the off-air of the nuclear auxiliaries of a BWR reactor

    Energy Technology Data Exchange (ETDEWEB)

    Patzelt, A.

    1983-12-01

    Contrary to the present opinion, the penetrating iodine fraction in the off-air from the auxiliaries of a BWR reactor may be higher than the values communicated in the relevant literature. This seems to be a result of internal processes in the systems in which ion exchanger resins are used. In these systems, filters made of a combination of impregnated and activated carbon have proved to be a better solution as experiments have shown. Systems of this type are recommended for general used.

  11. Calculation of releases of radioactive materials in gaseous and liquid effluents from boiling water reactors (BWR-GALE Code)

    Energy Technology Data Exchange (ETDEWEB)

    Bangart, R.L.; Bell, L.G.; Boegli, J.S.; Burke, W.C.; Lee, J.Y.; Minns, J.L.; Stoddart, P.G.; Weller, R.A.; Collins, J.T.

    1978-12-01

    The calculational procedures described in the report reflect current NRC staff practice. The methods described will be used in the evaluation of applications for construction permits and operating licenses docketed after January 1, 1979, until this NUREG is revised as a result of additional staff review. The BWR-GALE (Boiling Water Reactor Gaseous and Liquid Effluents) Code is a computerized mathematical model for calculating the release of radioactive material in gaseous and liquid effluents from boiling water reactors (BWRs). The calculations are based on data generated from operating reactors, field tests, laboratory tests, and plant-specific design considerations incorporated to reduce the quantity of radioactive materials that may be released to the environment.

  12. CFD Simulation of rigid venting of the containment of a BWR-5 Mark-II reactor; Simulacion CFD de los venteos rigidos de la contencion de un reactor BWR-5 Mark-II

    Energy Technology Data Exchange (ETDEWEB)

    Galindo G, I. F.; Vazquez B, A. K.; Velazquez E, L. [Instituto Nacional de Electricidad y Energias Limpias, Reforma 113, Col. Palmira, 62490 Cuernavaca, Morelos (Mexico); Tijerina S, F.; Tapia M, R., E-mail: francisco.tijerina@cfe.gob.mx [CFE, Central Nucleoelectrica Laguna Verde, Carretera Federal Cardel-Nautla Km 42.5, 91476 Municipio Alto Lucero, Veracruz (Mexico)

    2016-09-15

    In conditions of prolonged loss of external energy or a severe accident, venting to the atmosphere is an alternative to prevent overpressure and release of fission products from the primary containment of a nuclear reactor. Due to the importance of flow determination through rigid vents, a computational fluid dynamics (CFD) model is proposed to verify the capacity of rigid vents in the primary containment of a boiling water reactor (BWR) under different operating conditions (pressure, temperature and compositions of the fluids). The model predicts and provides detailed information on variables such as mass flow and velocity of the venting gases. In the proposed model the primary containment gas is vented to the atmosphere via rigid vents (pipes) from the dry and wet pit. Is assumed that the container is pressurized because is in a defined scenario, and at one point the venting is open and the gas released into the atmosphere. The objective is to characterize the flow and validate the CFD model for the overpressure conditions that occur in an accident such as a LOCA, Sbo, etc. The model is implemented with Ansys-Fluent general-purpose CFD software based on the geometry of the venting ducts of the containment of a BWR. The model is developed three-dimensional and resolves at steady state for compressible flow and includes the effects of the turbulence represented by the Reynolds stress model. The CFD results are compared with the values of a one-dimensional and isentropic model for compressible flow. The relative similarity of results leads to the conclusion that the proposed CFD model can help to predict the rigid venting capacity of the containment of a BWR, however more information is required for full validation of the proposed model. (Author)

  13. Genusa Bepu methodologies for the safety analysis of BWRs; Metodologias Bepu de Genusa para el analisis de seguridad de reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Trueba, M.; Garcia, J.; Goodson, C.; Ibarra, L.

    2016-08-01

    This article describes the BEPU methodologies developed by General Electric-Hitachi (GEH) for the evaluation of the BWR reactor safety analysis based on the TRACG best-estimate code. These methodologies are applicable to a wide range of events, operational transients (AOO), anticipated transients without scram (ATWS), loss of coolant accidents (LOCA) and instability events; to different BWR types operating commercially. General Electric (GE( designs and other vendors, including Generation III+ESBWR; to the new operation strategies, and to all types of BWR fuel. Their application achieves, among other benefits, a better understanding of the overall plant response and an improvement in margins to the operating limits; thus, the increase of flexibility in reactor operation and reduction in generation costs. (Author)

  14. Recent trends in the mitigation of the IGSCC through modifications in the water chemistry of BWR reactors; Tendencias recientes en la mitigacion del IGSCC mediante modificaciones en la quimica del agua de reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Diaz S, A.; Robles, E.F. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2003-07-01

    During the last years, the Nuclear Power stations had been that to adequate or to modify the parameters and operational conditions, attempting to maintain and to safeguard the integrity and functionality of its components and systems, as well as the personnel safety involved in its operation. In a Boiling water reactor (BWR), the chemical control of the water, constitutes one of the fundamental aspects to get a sure and reliable operation, having as main objectives: (a) The protection of the reactor vessel, of the structural materials of the same one and of the pipes and components of those recirculation systems against the Intergranular stress corrosion phenomena (IGSCC); (b) To guarantee the integrity of the nuclear fuel minimizing the corrosion phenomena in the fuel elements; and (c) The reduction of the operational dose of the personnel involved directly in the operation and maintenance by means of the control of the activated corrosion products. (Author)

  15. Key instrumentation in BWR plants

    Energy Technology Data Exchange (ETDEWEB)

    Laendner, Alexander; Stellwag, Bernhard; Fandrich, Joerg [AREVA NP GmbH, Erlangen (Germany)

    2011-01-15

    This paper describes water chemistry surveillance practices at boiling water reactor (BWR) power plants. The key instrumentation in BWR plants consists of on-line as well as off-line instrumentation. The chemistry monitoring and control parameters are predominantly based on two guidelines, namely the VGB Water Chemistry Guidelines and the EPRI Water Chemistry Guidelines. Control parameters and action levels specified in the VGB guideline are described. Typical sampling locations in BWR plants, chemistry analysis methods and water chemistry data of European BWR plants are summarized. Measurement data confirm the high quality of reactor water of the BWRs in Europe. (orig.)

  16. Simulation of the automatic depressurization system (Ads) for a boiling water reactor (BWR) based on RELAP; Simulacion del sistema de despresurizacion automatica (ADS) para un reactor de agua en ebullicion (BWR) basado en RELAP

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez G, C.; Chavez M, C., E-mail: ces.raga@gmail.com [UNAM, Facultad de Ingenieria, Circuito Interior, Ciudad Universitaria, 04510 Mexico D. F. (Mexico)

    2012-10-15

    The automatic depressurization system (Ads) of the boiling water reactor (BWR) like part of the emergency cooling systems is designed to liberate the vapor pressure of the reactor vessel, as well as the main vapor lines. At the present time in the Engineering Faculty, UNAM personnel works in the simulation of the Laguna Verde reactor based on the nuclear code RELAP/SCADAP and in the incorporation to the same of the emergency cooling systems. The simulation of the emergency cooling systems began with the inclusion of two hydrodynamic volumes, one source and another drain, and the incorporation of the initiation logic for each emergency system. In this work is defined and designed a simplified model of Ads of the reactor, considering a detail level based on the main elements that compose it. As tool to implement the proposed model, the RELAP code was used. The simulated main functions of Ads are centered in the quick depressurization of the reactor by means of the vapor discharge through the relief/safety valves to the suppression pool, and, in the event of break of the main vapor line, the reduction of the vessel pressure operates for that the cooling systems of the core to low pressure (Lpcs and Lpci) they can begin their operation. (Author)

  17. Simulation in 3 dimensions of a cycle 18 months for an BWR type reactor using the Nod3D program; Simulacion en 3 dimensiones de un ciclo de 18 meses para un reactor BWR usando el programa Nod3D

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez, N.; Alonso, G. [ININ, A.P. 18-1027, 11801 Mexico D.F. (Mexico)]. E-mail: nhm@nuclear.inin.mx; Valle, E. del [IPN, ESFM, 07738 Mexico D.F. (Mexico)

    2004-07-01

    The development of own codes that you/they allow the simulation in 3 dimensions of the nucleus of a reactor and be of easy maintenance, without the consequent payment of expensive use licenses, it can be a factor that propitiates the technological independence. In the Department of Nuclear Engineering (DIN) of the Superior School of Physics and Mathematics (ESFM) of the National Polytechnic Institute (IPN) a denominated program Nod3D has been developed with the one that one can simulate the operation of a reactor BWR in 3 dimensions calculating the effective multiplication factor (kJJ3, as well as the distribution of the flow neutronic and of the axial and radial profiles of the power, inside a means of well-known characteristics solving the equations of diffusion of neutrons numerically in stationary state and geometry XYZ using the mathematical nodal method RTN0 (Raviart-Thomas-Nedelec of index zero). One of the limitations of the program Nod3D is that it doesn't allow to consider the burnt of the fuel in an independent way considering feedback, this makes it in an implicit way considering the effective sections in each step of burnt and these sections are obtained of the code Core Master LEND. However even given this limitation, the results obtained in the simulation of a cycle of typical operation of a reactor of the type BWR are similar to those reported by the code Core Master LENDS. The results of the keJ - that were obtained with the program Nod3D they were compared with the results of the code Core Master LEND, presenting a difference smaller than 0.2% (200 pcm), and in the case of the axial profile of power, the maxim differs it was of 2.5%. (Author)

  18. Application of the MOVE algorithm for the identification of reduced order models of a core of a BWR type reactor; Aplicacion del algoritmo MOVE para la identificacion de modelos de orden reducido del nucleo de un reactor tipo BWR

    Energy Technology Data Exchange (ETDEWEB)

    Victoria R, M.A.; Morales S, J.B. [UNAM, DEPFI, Campus Morelos, en IMTA Jiutepec, Morelos (Mexico)]. e-mail: angelvr@gmail.com

    2005-07-01

    Presently work is applied the modified algorithm of the ellipsoid of optimal volume (MOVE) to a reduced order model of 5 differential equations of the core of a boiling water reactor (BWR) with the purpose of estimating the parameters that model the dynamics. The viability is analyzed of carrying out an analysis that calculates the global dynamic parameters that determine the stability of the system and the uncertainty of the estimate. The modified algorithm of the ellipsoid of optimal volume (MOVE), is a method applied to the parametric identification of systems, in particular to the estimate of groups of parameters (PSE for their initials in English). It is looked for to obtain the ellipsoid of smaller volume that guarantees to contain the real value of the parameters of the model. The PSE MOVE is a recursive identification method that can manage the sign of noise and to ponder it, the ellipsoid represents an advantage due to its easy mathematical handling in the computer, the results that surrender are very useful for the design of Robust Control since to smaller volume of the ellipsoid, better is in general the performance of the system to control. The comparison with other methods presented in the literature to estimate the reason of decline (DR) of a BWR is presented. (Author)

  19. An assessment of BWR (boiling water reactor) Mark-II containment challenges, failure modes, and potential improvements in performance

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, D.L.; Jones, K.R.; Dallman, R.J. (EG and G Idaho, Inc., Idaho Falls, ID (USA)); Wagner, K.C. (Science Applications International Corp., Albuquerque, NM (USA))

    1990-07-01

    This report assesses challenges to BWR Mark II containment integrity that could potentially arise from severe accidents. Also assessed are some potential improvements that could prevent core damage or containment failure, or could mitigate the consequences of such failure by reducing the release of fission products to the environment. These challenges and improvements are analyzed via a limited quantitative risk/benefit analysis of a generic BWR/4 reactor with Mark II containment. Point estimate frequencies of the dominant core damage sequences are obtained and simple containment event trees are constructed to evaluate the response of the containment to these severe accident sequences. The resulting containment release modes are then binned into source term release categories, which provide inputs to the consequence analysis. The output of the consequences analysis is used to construct an overall base case risk profile. Potential improvements and sensitivities are evaluated by modifying the event tree spilt fractions, thus generating a revised risk profile. Several important sensitivity cases are examined to evaluate the impact of phenomenological uncertainties on the final results. 75 refs., 25 figs., 65 tabs.

  20. MCTP, a code for the thermo-mechanical analysis of a fuel rod of BWR type reactors (Neutron part); MCTP, un codigo para el analisis termo-mecanico de una barra combustible de reactores tipo BWR (Parte Neutronica)

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez L, H.; Ortiz V, J. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: hhl@nuclear.inin.mx

    2003-07-01

    In the National Institute of Nuclear Research of Mexico a code for the thermo-mechanical analysis of the fuel rods of the BWR type reactors of the Nucleo electric Central of Laguna Verde is developed. The code solves the diffusion equation in cylindrical coordinates with several energy groups. The code, likewise, calculates the temperature distribution and power distribution in those fuel rods. The code is denominated Multi groups With Temperatures and Power (MCTP). In the code, the energy with which the fission neutrons are emitted it is divided in six groups. They are also considered the produced perturbations by the changes in the temperatures of the materials that constitute the fuel rods, the content of fission products, the uranium consumption and in its case the gadolinium, as well as the plutonium production. In this work there are present preliminary results obtained with the code, using data of operation of the Nucleo electric Central of Laguna Verde. (Author)

  1. A reactor noise analysis methodology for BWR core stability evaluation: application and assessment to Leibstadt stability tests

    Energy Technology Data Exchange (ETDEWEB)

    Dokhane, A. [Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland); Dokhane, A.; Ferroukhi, H.; Zimmermann, M.A. [Paul Scherrer Institut, Lab. for Reactor Physics and Systems Behavior, CH-5232 Villigen PSI (Switzerland); Aguirre, C. [Kernkraftwerk Leibstadt, CH-5325 Leibstadt (Switzerland)

    2005-07-01

    As a first step towards establishing a best-estimate methodology for the evaluation of BWR core stability parameters, i.e. the decay ratio and resonance frequency, from measured reactor noise signals, a systematic approach has recently been developed and adopted at PSI for the analysis of the Swiss BWRs. The aim is to evaluate stability tests in a consistent manner at any operating condition in the power/flow map and for any operating cycle. This methodology principally consists in a general reactor noise analysis where as much as possible information recorded during the tests is investigated prior to determining 'core representative' stability parameters along with an associated uncertainty range. A central part in this approach is that a time series analysis of all measured neutron flux signals, rather than only one or few signals, is performed. In addition, for each signal, three different model-order optimization methods are systematically employed to take into account the sensitivity upon the model-order. The adopted methodology is then applied to the evaluation of the core stability measurements performed at the Kernkraftwerk Leibstadt nuclear power plant, Switzerland, during cycles 10, 13 and 19. A total of 28 tests are hence analyzed. This is primarily done in order to obtain a broad range of tests to serve as basis for the validation of the coupled neutronic/thermal-hydraulic codes used at PSI for BWR stability calculations. In addition, in order to assess the results obtained with the current methodology, a comparative study has been carried out with respect to results from previously developed and applied procedures. The results show a good agreement between the current method and the other methods. (authors)

  2. VGB guideline for the water in nuclear power plants with light water reactors (BWR). VGB-R 401 J; VGB-Richtlinie fuer das Wasser in Kernkraftwerken mit Leichtwasserreaktoren (SWR). VGB-R 401 J

    Energy Technology Data Exchange (ETDEWEB)

    Rosskamp, M. [Vattenvall Europe Nuclear Energy, Kernkraftwerk Brunsbuettel GmbH und Co OHG (Germany); Albrecht, N. [Vattenvall Europe Nuclear Energy, Kernkraftwerk Kruemmel GmbH und Co OHG, Geesthacht (Germany); Ilg, U. [EnBW Kraftwerke AG, Kernkraftwerk Philippsburg (Germany); Neder, H. [E.ON Kernkraftwerk GmbH, Kernkraftwerk Isar, Essenbach (Germany); Reitzner, U. [AREVA NP GmbH, Erlangen (Germany); Riedmueller, B. [Kernkraftwerk Gundremmingen GmbH (Germany); Rutschow, D. [VGB-Geschaeftsstelle, Essen (Germany)

    2007-07-01

    The new VGB guideline for light water reactor (BWR) is presented. The guideline specifies the classical, oxidative water chemistry for BWR. Principal strategies of water chemistry are described. Recommendations are made for deviations of normal operation. The guideline specifies - based on latest findings - especially chloride and sulphate in reactor water in view to corrosion resistance of austenitic materials, normal operating values and action levels. (orig.)

  3. Comparison of results for burning with BWR reactors CASMO and SCALE 6.2 (TRITON / NEWT); Comparacion de los resultados de quemado para reactores BWR con CASMO y SCALE 6.2 (TRITON/NEWT)

    Energy Technology Data Exchange (ETDEWEB)

    Mesado, C.; Miro, R.; Barrachina, T.; Verdu, G.

    2014-07-01

    In this paper we compare the results from two codes burned, CASMO and SCALE 6.2 (TRITON). To do this, is simulated all segments corresponding to a boiling water reactor (BWR) using both codes. In addition, to account for different working points, simulations changing the instantaneous variables, these are repeated: void fractions (6 points), fuel temperature (6 points) and control rods (two points), with a total of 72 possible combinations of different instantaneous variables for each segment. After all simulations are completed for each segment, we can reorder the obtained cross sections, as SCALE CASMO both, to create a library of compositions nemtab format. This format is accepted by the neutronic code of nodal diffusion, PARCS v2.7. Finally compares the results obtained with PARCS and with the SIMULATE3 -SIMTAB methodology to level of full reactor. Also, we have made use of the KENO-VI and MCDANCOFF modules belonging to SCALE. The first is a Monte Carlo transport code with which you can validate the value of the multiplier, the second has been used to obtain values of Dancoff factor and increase the accuracy of model SCALE. (Author)

  4. Mitigation strategies of intergranular corrosion in systems of reactors of water boiling (BWR). Combined action of the chemistry of the hydrogen and the oxygen; Estrategias de mitigacion de la corrosion intergranular en sistemas de reactores de agua en ebullicion (BWR). Accion combinada de la quimica del hidrogeno y del oxigeno

    Energy Technology Data Exchange (ETDEWEB)

    Verdugo, M.

    2015-07-01

    Inter-Granular Stress Corrosion cracking (IGSCC) in austenitic stainless steel and in austenitic nickel-based alloys has been the subject of many studies the aim of which was to resolve one of the main problems faced by BWR nuclear power plants since the 1960s. This corrosion phenomenon is the result of the combined action of three factors: sensitization of the material, high local stresses and an aggressive medium. This paper deals with these factors separately and analyzes the oxidative chemistry of BWR reactors (aggressivity of the medium) as one the main causes if IGSCC. (Author)

  5. Liquid level, void fraction, and superheated steam sensor for nuclear-reactor cores. [PWR; BWR

    Science.gov (United States)

    Tokarz, R.D.

    1981-10-27

    This disclosure relates to an apparatus for monitoring the presence of coolant in liquid or mixed liquid and vapor, and superheated gaseous phases at one or more locations within an operating nuclear reactor core, such as pressurized water reactor or a boiling water reactor.

  6. Characterization of welding of AISI 304l stainless steel similar to the core encircling of a BWR reactor; Caracterizacion de soldaduras de acero inoxidable AISI 304L similares a las de la envolvente del nucleo de un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Gachuz M, M.E.; Palacios P, F.; Robles P, E.F. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2003-07-01

    Plates of austenitic stainless steel AISI 304l of 0.0381 m thickness were welded by means of the SMAW process according to that recommended in the Section 9 of the ASME Code, so that it was reproduced the welding process used to assemble the encircling of the core of a BWR/5 reactor similar to that of the Laguna Verde Nucleo electric plant, there being generated the necessary documentation for the qualification of the one welding procedure and of the welder. They were characterized so much the one base metal, as the welding cord by means of metallographic techniques, scanning electron microscopy, X-ray diffraction, mechanical essays and fracture mechanics. From the obtained results it highlights the presence of an area affected by the heat of up to 1.5 mm of wide and a value of fracture tenacity (J{sub IC}) to ambient temperature for the base metal of 528 KJ/m{sup 2}, which is diminished by the presence of the welding and by the increment in the temperature of the one essay. Also it was carried out an fractographic analysis of the fracture zone generated by the tenacity essays, what evidence a ductile fracture. The experimental values of resistance and tenacity are important for the study of the structural integrity of the encircling one of the core. (Author)

  7. Thermomechanical analysis of a fuel rod in a BWR reactor using the FUELSIM code; Analisis termomecanico de una barra de combustible de un reactor BWR utilizando el codigo FUELSIM

    Energy Technology Data Exchange (ETDEWEB)

    Pantoja C, R. [Escuela Superior de Fisica y Matematicas, Departamento de Ingenieria Nuclear, IPN, Av. Instituto Politecnico Nacional s/n, Col. San Pedro Zacatenco, 07738 Mexico, D. F. (Mexico); Ortiz V, J.; Araiza M, E. [ININ, Departamento de Sistemas Nucleares, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)], e-mail: rapaca78@yahoo.com.mx

    2009-10-15

    The thermomechanical behaviour of a fuel rod exposed to irradiation is a complex process in which are coupled great quantity of interrelated physical-chemical phenomena, for that analysis of rod performance in the core of a nuclear power reactor is realized generally with computation codes that integrate several phenomena expected during the time life of fuel rod in the core. An application of this type of thermomechanical codes is to predict, inside certain reliability margin, the design parameters that would be required to adjust, in order to get a better economy or rod performance, for a systematic approach to the fuel design optimization. FUELSIM is a thermomechanical code based on the models of FRAPCON code, which was developed under auspice of Nuclear Regulatory Commission of USA. FUELSIM allows iterative calculations like part of its programming structure, allowing search of extreme cases of behaviour, probabilistic analysis (or statistical), parametric analysis (or sensibility) and also can include as entrance data to the uncertainties associated with production data, code parameters and associated models. In this work is reported a first analysis of thermomechanical performance of a typical fuel rod used in a BWR 5/6. Results of maximum temperatures are presented in the fuel center and of axial deformation, for the 10 axial nodes in that the active longitude of fuel rod was divided. (Author)

  8. Stability analysis of a recycling circuit of a BWR type reactor. Theoretical study; Analisis de estabilidad de un circuito de recirculacion de un reactor del tipo BWR. Estudio teorico

    Energy Technology Data Exchange (ETDEWEB)

    Salinas H, J.G.; Espinosa P, G. [Universidad Autonoma Metropolitana-Iztapalapa, 09000 Mexico D.F. (Mexico); Gonzalez M, V.M. [Comision Nacional de Seguridad Nuclear y Salvaguardias, 04000 Mexico D.F. (Mexico)

    2000-07-01

    The Technology, Regulation and Services Management of the National Commission of Nuclear Safety and Safeguards financed and in coordinate form with the I.P.H. Department of the Metropolitan Autonomous-Iztapalapa University developed the present project with the purpose of studying the effect of the recycling system on the linear stability of a BWR reactor whose reference central is the Laguna Verde power station. The present project forms part of a work series focused to the linear stability of the nuclear reactor of the Unit 1 at Laguna Verde power station. The components of the recycling system considered for the study of stability are the recycling external circuit (recycling pumps, valves) and the internal circuit (downcomer, jet pumps, lower full, driers, separators). The mathematical model is obtained applying mass balances and movement quantity in each one of the mentioned circuits. With respect to the nucleus model two regions are considered, the first one is made of a flow in one phase and the second one of a flow in two phases. For modelling the biphasic region it is considered homogenous flow. Generally it is studied the system behavior in the frequency domain starting from the transfer function applied to four operational states which correspond to the lower stability zone in the map power-flow of the Unit 1 of Laguna Verde power station. The Nyquist diagrams corresponding to each state as well as their characteristic frequency were determined. The results show that exists a very clear dependence of the power-flow relation on the stability of the system. It was found that the boiling length is an important parameter for the linear stability of the system. The obtained results show that the characteristic frequencies in unstability zones are similar to the reported data of the Unit 1 of the Laguna Verde power station in the event of power oscillations carried out in January 1995. (Author)

  9. A method of reactor power decrease by 2DOF control system during BWR power oscillation

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, Nobuyuki; Suzuki, Katsuo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-09-01

    Occurrence of power oscillation events caused by void feedback effects in BWRs operated at low-flow and high-power condition has been reported. After thoroughly examining these events, BWRs have been equipped with the SRI (Selected Rod Insertion) system to avoid the power oscillation by decreasing the power under such reactor condition. This report presents a power control method for decreasing the reactor power stably by a two degree of freedom (2DOF) control. Performing a numerical simulation by utilizing a simple reactor dynamics model, it is found that the control system designed attains a satisfactory control performance of power decrease from a viewpoint of setting time and oscillation. (author)

  10. SCALE-4 Analysis of LaSalle Unit 1 BWR Commercial Reactor Critical Configuration

    Energy Technology Data Exchange (ETDEWEB)

    Gauld, I.C.

    2000-03-16

    Five commercial reactor criticals (CRCs) for the LaSalle Unit 1 boiling-water reactor have been analyzed using KENO V.a, the Monte Carlo criticality code of the SCALE 4 code system. The irradiated fuel assembly isotopics for the criticality analyses were provided by the Waste Package Design team at the Yucca Mountain Project in the United States, who performed the depletion calculations using the SAS2H sequence of SCALE 4. The reactor critical measurements involved two beginning-of-cycle and three middle-of-cycle configurations. The CRCs involved relatively low-cycle burnups, and therefore contained a relatively high gadolinium poison content in the reactor assemblies. This report summarizes the data and methods used in analyzing the critical configurations and assesses the sensitivity of the results to some of the modeling approximations used to represent the gadolinium poison distribution within the assemblies. The KENO V.a calculations, performed using the SCALE 44GROUPNDF5 ENDF/B-V cross-section library, yield predicted k{sub eff} values within about 1% {Delta}k/k relative to reactor measurements for the five CRCs using general 8-pin and 9-pin heterogeneous gadolinium poison pin assembly models.

  11. SCALE-4 Analysis of LaSalle Unit 1 BWR Commercial Reactor Critical Configurations

    Energy Technology Data Exchange (ETDEWEB)

    Gauld, I.C.

    2000-03-01

    Five commercial reactor criticals (CRCs) for the LaSalle Unit 1 boiling-water reactor have been analyzed using KENO V.a, the Monte Carlo criticality code of the SCALE 4 code system. The irradiated fuel assembly isotopics for the criticality analyses were provided by the Waste Package Design team at the Yucca Mountain Project in the US, who performed the depletion calculations using the SAS2H sequence of SCALE 4. The reactor critical measurements involved two beginning-of-cycle and three middle-of-cycle configurations. The CRCs involved relatively low-cycle burnups, and therefore contained a relatively high gadolinium poison content in the reactor assemblies. This report summarizes the data and methods used in analyzing the critical configurations and assesses the sensitivity of the results to some of the modeling approximations used to represent the gadolinium poison distribution within the assemblies. The KENO V.a calculations, performed using the SCALE 44GROUPNDF5 ENDF/B-V cross-section library, yield predicted k{sub eff} values within about 1% {Delta}k/k relative to reactor measurements for the five CRCs using general 8-pin and 9-pin heterogeneous gadolinium poison pin assembly models.

  12. Construction of an external electrode for determination of electrochemical corrosion potential in normal operational conditions of an BWR type reactor for hot cells; Construccion de un electrodo externo para determinacion del potencial de corrosion electroquimico en condiciones normales de operacion de un reactor tipo BWR para celdas calientes

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar T, J.A.; Rivera M, H.; Hernandez C, R. [Departamento de Sintesis y Caracterizacion de Materiales, Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    2001-07-01

    The behavior of the corrosion processes at high temperature requires of external devices that being capable to resist a temperature of 288 Centigrade and a pressure of 80 Kg/cm{sup 2}, to give stable and reproducible results of some variable and resisting physically and chemically the radiation. The external electrode of Ag/AgCl fulfils all the requirements in the determination of the electrochemical corrosion potential under normal operational conditions of a BWR type reactor in hot cells. (Author)

  13. Concept of a self-sustaining cooling system for after-heat removal in BWR-type reactors; Konzept eines autarken Kuehlsystems zur Nachwaermeabfuhr in Siedewasserreaktoren

    Energy Technology Data Exchange (ETDEWEB)

    Venker, J. [RWE Technology GmbH, Essen (Germany). Nukleartechnologie; Stuttgart Univ. (Germany). Inst. fuer Kernenergetik und Energiesysteme (IKE); Lavante, D. von [TUEV Rheinland, Koeln (Germany); Buck, M.; Starflinger, J. [Stuttgart Univ. (Germany). Inst. fuer Kernenergetik und Energiesysteme (IKE); Gitzel, D. [RWE Technology GmbH, Essen (Germany). Nukleartechnologie

    2013-07-01

    The concept, technical feasibility and potential capability of a new self-sustaining after-heat removal system based on supercritical carbon dioxide is described. The effect of the system on the plant behavior of appropriately retrofitted BWR-type reactors is discussed. Based on calculations using the thermal hydraulic code ATHLET it is shown that the safe after-heat removal time of existing BWR-type reactors in case of station blackout can be increased for several hours. The calculations have also shown that a enduring control of the station blackout situation cannot be reached by the retrofitting of the pressure relief system. The question is raised whether the pressure relief is reasonable independent of the accident scenario. Without the possibility of further coolant supply in case of station blackout the pressure relief will enhance the dry-out of the reactor core. The high-pressure path for the primary circuit increases the time for possible external measures to activate ECCS or active after-heat removal.

  14. Fuel design with low peak of local power for BWR reactors with increased nominal power; Diseno de un combustible con bajo pico de potencia local para reactores BWR con potencia nominal aumentada

    Energy Technology Data Exchange (ETDEWEB)

    Perusquia C, R.; Montes, J.L.; Hernandez, J.L.; Ortiz, J.J.; Castillo, A. [ININ, 52750 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: mrpc@nuclear.inin.mx

    2006-07-01

    The Federal Commission of Electricity recently announcement the beginning of the works related with the increase of the power to 120% of the original nominal one in the Boiling Water Reactors (BWR) of the Laguna Verde Central (CLV): In the National Institute of Nuclear Research (ININ) are carried out studies of the impact on the design of the recharge of derived fuel of this increase. One of the main effects of the power increase type that it is promoting, is the increment of the flow of generated vapor, what takes, to a bigger fraction of vacuum in the core presenting increased values of the maximum fraction to the limit, so much of the ratio of lineal heat generation (XFLPD) as of the ratio of critic power (MFLCPR). In the made studies, it is found that these fractions rise lineally with the increase of the nominal power. Considering that the reactors of the CLV at the moment operate to 105% of the original nominal power, it would imply an increment of the order of 13.35% in the XFLPD and in the MFLCPR operating to a nominal power of 120% of the original one. This would propitiate bigger problems to design appropriately the fuel cycle and the necessity, almost unavoidable, of to resort to a fuel assembly type more advanced for the recharges of the cores. As option, in the ININ the feasibility of continuing using the same type of it fuel assembles that one has come using recently in the CLV, the type GE12 is analyzed. To achieve it was outlined to diminish the peak factor of local power (LPPF) of the power cells that compose the fuel recharge in 13.35%. It was started of a fuel design previously used in the recharge of the unit 1 cycle 12 and it was re-design to use it in the recharge design of the cycle 13 of the unit 1, considering an increase to 120% of the original power and the same requirements of cycle extension. For the re-design of the fuel assembly cell it was used the PreDiCeldas computer program developed in the ININ. It was able to diminish the LPPF

  15. Nuclear fuel activity with minor actinides after their useful life in a BWR; Actividad del combustible nuclear con actinidos menores despues de su vida util en un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Martinez C, E.; Ramirez S, J. R.; Alonso V, G., E-mail: eduardo.martinez@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2016-09-15

    Nuclear fuel used in nuclear power reactors has a life cycle, in which it provides energy, at the end of this cycle is withdrawn from the reactor core. This used fuel is known as spent nuclear fuel, a strong problem with this fuel is that when the fuel was irradiated in a nuclear reactor it leaves with an activity of approximately 1.229 x 10{sup 15} Bq. The aim of the transmutation of actinides from spent nuclear fuel is to reduce the activity of high level waste that must be stored in geological repositories and the lifetime of high level waste; these two achievements would reduce the number of necessary repositories, as well as the duration of storage. The present work is aimed at evaluating the activity of a nuclear fuel in which radioactive actinides could be recycled to remove most of the radioactive material, first establishing a reference of actinides production in the standard nuclear fuel of uranium at end of its burning in a BWR, and a fuel rod design containing 6% of actinides in an uranium matrix from the enrichment tails is proposed, then 4 standard uranium fuel rods are replaced by 4 actinide bars to evaluate the production and transmutation of the same, finally the reduction of actinide activity in the fuel is evaluated. (Author)

  16. BWR Steam Dryer Alternating Stress Assessment Procedures

    Energy Technology Data Exchange (ETDEWEB)

    Morante, R. J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Hambric, S. A. [Brookhaven National Lab. (BNL), Upton, NY (United States); Ziada, S. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2016-12-01

    This report presents an overview of Boiling Water Reactor (BWR) steam dryer design; the fatigue cracking failures that occurred at the Quad Cities (QC) plants and their root causes; a history of BWR Extended Power Uprates (EPUs) in the USA; and a discussion of steam dryer modifications/replacements, alternating stress mechanisms on steam dryers, and structural integrity evaluations (static and alternating stress).

  17. Recriticality in a BWR (boiling water reactor) following a core damage event

    Energy Technology Data Exchange (ETDEWEB)

    Scott, W.B.; Harrison, D.G.; Libby, R.A.; Tokarz, R.D. (Pacific Northwest Lab., Richland, WA (USA)); Wooton, R.D.; Denning, R.S.; Tayloe, R.W. Jr. (Battelle Memorial Inst., Columbus, OH (USA))

    1990-12-01

    This report describes the results of a study conducted by Pacific Northwest Laboratory to assist the US Nuclear Regulatory Commission in evaluating the potential for recriticality in boiling water reactors (BWRs) during certain low probability severe accidents. Based on a conservative bounding analysis, this report concludes that there is a potential for recriticality in BWRs if core reflood occurs after control blade melting has begun but prior to significant fuel rod melting. However, a recriticality event will most likely not generate a pressure pulse significant enough to fail the vessel. Instead, a quasi-steady power level would result and the containment pressure and temperature would increase until the containment failure pressure is reached, unless actions are taken to terminate the event. Two strategies are identified that would aid in regaining control of the reactor and terminate the recriticality event before containment failure pressures are reached. The first strategy involves initiating boration injection at or before the time of core reflood if the potential for control blade melting exists. The second strategy involves initiating residual heat removal suppression pool cooling to remove the heat load generated by the recriticality event and thus extend the time available for boration. 31 figs., 17 tabs.

  18. Decay profiles of {beta} and {gamma} for a radionuclide inventory in equilibrium cycle of a BWR type reactor; Perfiles de decaimiento de radiacion {beta} y {gamma} para un inventario de radionuclidos en ciclo de equilibrio de un reactor tipo BWR

    Energy Technology Data Exchange (ETDEWEB)

    Salaices, M.; Sandoval, S.; Ovando, R. [Instituto de Investigaciones Electricas. Gerencia de Energia Nuclear, Av. Reforma 113 Col. Palmira. 62490 Cuernavaca, Morelos (Mexico)]. e-mail: sal@iie.org.mx

    2007-07-01

    Presently work the {beta} and {gamma} radiation decay profiles for a radionuclides inventory in equilibrium cycle of a BWR type reactor is presented. The profiles are presented in terms of decay in the activity of the total inventory as well as of the chemical groups that conform the inventory. In the obtaining of the radionuclides inventory in equilibrium cycle the ORIGEN2 code, version 1 was used, which simulates fuel burnup cycles and it calculates the evolution of the isotopic composition as a result of the burnt one, irradiation and decay of the nuclear fuel. It can be observed starting from the results that the decrease in the activity for the initial inventory and the different chemical groups that conform it is approximately proportional to the base 10 logarithm of the time for the first 24 hours of having concluded the burnt one. It can also be observed that the chemical groups that contribute in more proportion to the total activity of the inventory are the lanthanides-actinides and the transition metals, with 39% and 28%, respectively. The groups of alkaline earth metals, halogens, metalloids, noble gases and alkaline metals, contribute with percentages that go from the 8 to 5%. The groups that less they contribute to the total activity of the inventory they are the non metals and semi-metals with smaller proportions that 1%. The chemical groups that more contribute to the energy of {beta} and {gamma} radiation its are the transition metals and the lanthanides-actinides with a change in the order of importance at the end of the 24 hours period. The case of the halogens is of relevance for the case of the {gamma} radiation energy due that occupying the very near third site to the dimensions of the two previous groups. Additionally, the decay in the activity for the total inventory and the groups that conform it can be simulated by means of order 6 polynomials or smaller than describe its behavior appropriately. The results presented in this work, coupled

  19. Spatial and model-order based reactor signal analysis methodology for BWR core stability evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Dokhane, A. [Paul Scherrer Institute, Laboratory for Reactor Physics and Systems Behavior, CH-5232 Villigen PSI (Switzerland) and Ecole Polytechnique Federale de Lausanne, CH-1015 Lausanne (Switzerland)]. E-mail: adokhane@ksu.edu.sa; Ferroukhi, H. [Paul Scherrer Institute, Laboratory for Reactor Physics and Systems Behavior, CH-5232 Villigen PSI (Switzerland)]. E-mail: hakim.ferroukhi@psi.ch; Zimmermann, M.A. [Paul Scherrer Institute, Laboratory for Reactor Physics and Systems Behavior, CH-5232 Villigen PSI (Switzerland); Aguirre, C. [Kernkraftwerk Leibstadt, CH-5325 Leibstadt (Switzerland)

    2006-11-15

    A new methodology for the boiling water reactor core stability evaluation from measured noise signals has been recently developed and adopted at the Paul Scherrer Institut (PSI). This methodology consists in a general reactor noise analysis where as much as possible information recorded during the tests is investigated prior to determining core representative stability parameters, i.e. the decay ratio (DR) and the resonance frequency, along with an associated estimate of the uncertainty range. A central part in this approach is that the evaluation of the core stability parameters is performed not only for a few but for ALL recorded neutron flux signals, allowing thereby the assessment of signal-related uncertainties. In addition, for each signal, three different model-order optimization methods are systematically employed to take into account the sensitivity upon the model-order. The current methodology is then applied to the evaluation of the core stability measurements performed at the Leibstadt NPP, Switzerland, during cycles 10, 13 and 19. The results show that as the core becomes very stable, the method-related uncertainty becomes the major contributor to the overall uncertainty range while for intermediate DR values, the signal-related uncertainty becomes dominant. However, as the core stability deteriorates, the method-related and signal-related spreads have similar contributions to the overall uncertainty, and both are found to be small. The PSI methodology identifies the origin of the different contributions to the uncertainty. Furthermore, in order to assess the results obtained with the current methodology, a comparative study is for completeness carried out with respect to results from previously developed and applied procedures. The results show a good agreement between the current method and the other methods.

  20. BWR simulation in a stationary state for the evaluation of fuel cell design; Simulacion de un reactor BWR en estado estacionario para la evaluacion del diseno de celdas de combustible

    Energy Technology Data Exchange (ETDEWEB)

    Montes T, J. L.; Ortiz S, J. J.; Perusquia del C, R.; Castillo M, A., E-mail: joseluis.montes@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2014-10-15

    In this paper the simulation of a BWR in order to evaluate the performance of a set of fuel assemblies under stationary state in three dimensions (3-D) is presented. 15 cases selected from a database containing a total of 18225 cases are evaluated. The main selection criteria were based on the results of the design phase of the power cells in two dimensions (2-D) and 3-D initial study. In 2-D studies the parameters that were used to qualify and select the designs were basically the local power peaking factor and neutron multiplication factor of each fuel cell. In the initial 3-D study variables that defined the quality of results, and from which the selection was realized, are the margins to thermal limits of reactor operation and the value of the effective multiplication factor at the end of cycle operation. From the 2-D and 3-D results of the studies described a second 3-D study was realized, where the optimizations of the fuel reload pattern was carried out. The results presented in this paper correspond to this second 3-D study. It was found that the designs of the fuel cell they had a similar behavior to those provided by the fuel supplier of reference BWR. Particularly it noted the impact of reload pattern on the cold shut down margin. An estimate of the operation costs of reference cycle analyzed with each one designed reload batch was also performed. As a result a positive difference (gain) up to 10,347 M/US D was found. (Author)

  1. Calculation of the neutron flux and fluence in the covering of the nucleus and the vessel of a BWR; Calculo del flujo neutronico y fluencia en la envolvente del nucleo y la vasija de un reactor nuclear BWR

    Energy Technology Data Exchange (ETDEWEB)

    Martinez C, E.; Del Valle G, E. [IPN, Escuela Superior de Fisica y Matematicas, U. P. Adolfo Lopez Mateos, Col. Lindavista, 07738 Mexico D. F. (Mexico); Longoria G, L. C., E-mail: evalle@esfm.ipn.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2011-11-15

    One of the main objectives related with the safety in any nuclear power plant, including the nuclear power plant of Laguna Verde, is to guarantee the structural integrity of the pressure vessel of the reactor. To identify and quantifying the damage caused be neutron irradiation in the vessel of any nuclear reactor, is necessary to know as much the neutron flux as the fluence that it has been receiving during their time of operation life, since the observables damages by means of tests mechanics are products of micro-structural effects, induced by neutron irradiation, therefore, is important the study and prediction of the neutron flux to have a better knowledge of the damage that are receiving these materials. In our calculation the code DORT was used, which solves the transport equation in discreet coordinates and in two dimensions (x-y, r-{theta} and r-z), in accord to the regulator guide, it requires to make and approach of the neutron flux in three dimensions by means of the Synthesis Method. Whit this method is possible to achieve a representation of the flux in 3D combining or synthesizing the calculated fluxes by DORT code in r-{theta}, r-z and r. In this work the application of the Synthesis Method is presented, according to the Regulator Guide 1.190, to determine the fluxes 3D in the interns of a BWR using three different space meshes. (Author)

  2. Simulation of the operational monitoring of a BWR with Simulate-3; Simulacion del seguimiento operacional de un reactor BWR con Simulate-3

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez F, J. O.; Martin del Campo M, C.; Fuentes M, L.; Francois L, J. L., E-mail: ace.jo.cu@gmail.com [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Ciudad Universitaria, 04510 Ciudad de Mexico (Mexico)

    2015-09-15

    This work was developed in order to describe the methodology for calculating the fuel burned of nuclear power reactors throughout the duration of their operating cycle and for each fuel reload. In other words, simulate and give monitoring to the main operation parameters of sequential way along its operation cycles. For this particular case, the operational monitoring of five consecutive cycles of a reactor was realized using the information reported by their processes computer. The simulation was performed with the Simulate-3 software and the results were compared with those of the process computer. The goal is to get the fuel burned, cycle after cycle for obtain the state conditions of the reactor needed for the fuel reload analyses, stability studies and transients analysis, and the development of a methodology that allows to manage and resolve similar cases for future fuel cycles of the nuclear power plant and explore the various options offered by the simulator. (Author)

  3. BWR Assembly Optimization for Minor Actinide Recycling

    Energy Technology Data Exchange (ETDEWEB)

    G. Ivan Maldonado; John M. Christenson; J.P. Renier; T.F. Marcille; J. Casal

    2010-03-22

    The Primary objective of the proposed project is to apply and extend the latest advancements in LWR fuel management optimization to the design of advanced boiling water reactor (BWR) fuel assemblies specifically for the recycling of minor actinides (MAs).

  4. Determination of stresses caused by fluctuation of acoustic load in the steam dryers of a BWR; Determinacion de esfuerzos originados por fluctuacion de carga acustica en los secadores de vapor de un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Centeno P, J.; Quezada G, S.; Prieto G, A.; Vazquez R, A.; Espinosa P, G. [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Av. San Rafael Atlixco No. 186, Col. Vicentina, 09340 Mexico D. F. (Mexico); Nunez C, A., E-mail: javcuami26@hotmail.com [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Jose Ma. Barragan No. 779, Col. Narvarte, 03020 Mexico D. F. (Mexico)

    2014-10-15

    The extended power up-rate (EPU) in a nuclear power plant cause various problems in BWR components also in the steam system. This due to increased steam flow generated in the reactor and is conveyed to the turbine by the four main steam lines (MSL). One of the most serious problems is the generation of acoustic pressure loads in the metal structure of the steam dryer which eventually leads to fatigue failure and even the appearance of cracks, and in turn it causes loose parts that are entrained by the steam and transported in the MSL. This problem is due to the fluctuation of load acoustics caused by the union of the safety or relief valves (SRV) with the MSL, spreading through these to reach the reactor pressure vessel (RPV) where the effect of resonance of the acoustic wave is amplified and impacts directly in the supporting structure of the steam dryer, skirt and the panels where the mixture liquid-steam is dried, by centrifugation effect and runoff of liquid water. Efforts in the steam dryer operating conditions of EPU for two cases will be analyzed in this work, the first is before the installation of Acoustic Side Branch (ASB), and in the second case we consider the installation of said ASB in the standpipes of SRV. The analysis was performed with numerical experiments on a platform for computational fluid dynamics with virtual geometries previously designed based on the actual components of the reactor and steam system. The model to study is delimited by the top of the RPV, the steam dryer and a section of each of the four MSL with ten standpipes of SRV. With the obtained data and considering the mechanical-structural properties of the steam dryer material, we can evaluate the mechanical resistance to impacts by acoustic pressure load and its possible deformation or cracking. (Author)

  5. Study of instabilities in phase by using the tool {sup D}ynamics{sup :} analysis of the evolution space temporary of the waves of density in channels of reactors BWR; Estudio de las Inestabilidades en Fase Mediante la Herramienta Dinamics: analisis de la Evolucion Espacio Temporal de las Ondas de Densidad en Canales de Reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Munoz-Cobo, J. L.; Escriva, R.; Merino, R.; Melara, J.

    2013-07-01

    This paper presents the basics of Dynamics V2 to code It allows calculations of stability for oscillations in phase in BWR reactors in the time domain. The equations of the model are exposed and is the integration of the equations. The model can be used in a large number of nodes thrust for the calculations to an acceptable computational cost, it has simplified dynamics of recirculation loop and the code has been incorporated the Oscillation in phase boundary conditions. The code incorporates the equations of boiling sub-cooled which allows to make more realistic calculations as well as subroutines to calculate the subroutines-based properties of the MATPRO and ASME.

  6. High Fidelity BWR Fuel Simulations

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Su Jong [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-08-01

    This report describes the Consortium for Advanced Simulation of Light Water Reactors (CASL) work conducted for completion of the Thermal Hydraulics Methods (THM) Level 3 milestone THM.CFD.P13.03: High Fidelity BWR Fuel Simulation. High fidelity computational fluid dynamics (CFD) simulation for Boiling Water Reactor (BWR) was conducted to investigate the applicability and robustness performance of BWR closures. As a preliminary study, a CFD model with simplified Ferrule spacer grid geometry of NUPEC BWR Full-size Fine-mesh Bundle Test (BFBT) benchmark has been implemented. Performance of multiphase segregated solver with baseline boiling closures has been evaluated. Although the mean values of void fraction and exit quality of CFD result for BFBT case 4101-61 agreed with experimental data, the local void distribution was not predicted accurately. The mesh quality was one of the critical factors to obtain converged result. The stability and robustness of the simulation was mainly affected by the mesh quality, combination of BWR closure models. In addition, the CFD modeling of fully-detailed spacer grid geometry with mixing vane is necessary for improving the accuracy of CFD simulation.

  7. Behavior to the fracture of an AISI 304 stainless steel sensitized in BWR reactor conditions (288 degrees Centigrade and 80 Kg/cm{sup 2}); Comportamiento a la fractura de un acero inoxidable AISI 304 sensibilizado en condiciones de reactor BWR (288 grados Centigrados y 80 Kg/cm{sup 2})

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez C, R.; Diaz S, A.; Garcia R, R.; Aguilar T, A.; Gachuz M, M.; Arganis J, C.; Merino C, J. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1999-07-01

    It is a knew fact that ductility of a lot of structural alloys can be deteriorated by the environment effect which are exposed, and that their consequent embrittlement can put in doubt the safety of their functioning; such is the case of austenitic stainless steels used in internal components of the BWR type reactors which not only is subjected to the effect combined of the aggressive environment which surround it (pressure, temperature, corrosion potential, conductivity medium, local state of efforts, etc.), but also to the action of present neutron radiation, manifesting microstructural changes which are reflected in the augmentation of its susceptibility to the intergranular cracking, phenomena generally known as IASCC ''Irradiation Assisted Stress Corrosion Cracking''. Once appeared the cracking in the material, the useful life of a component is limited by the rapidity to growth of these cracking, making necessary evaluations which can to predict its behavior, therefore the present work shows the preliminary results for determining the behavior to the fracture of an AISI 304 stainless steel sensitized, in a dynamic recirculation circuit which allows to simulate the operation conditions of a BWR reactor (288 Centigrade and 80 kg/cm{sup 2}). (Author)

  8. Updating of the costs of the nuclear fuels of the equilibrium reloading of the A BWR and EPR reactors; Actualizacion de los costos de combustible nuclear de la recarga de equilibrio de los reactores ABWR y EPR

    Energy Technology Data Exchange (ETDEWEB)

    Ortega C, R.F. [FI-UNAM, 04510 Mexico D.F. (Mexico)]. e-mail: rortega@fi-b.unam.mx

    2008-07-01

    In the last two and a half years, the price of the uranium in the market spot has ascended of US$20.00 dollars by lb U{sub 3O}8 in January, 2005 to a maximum of US$137.00 dollars by Ib U{sub 3}O{sub 8} by the middle of 2007. At the moment this price has been stabilized in US$90.00 dollars by Ib U{sub 3}O{sub 8} such for the market spot, like for the long term contracts. In this work the reasons of this increment are analyzed, as well as their impact in the fuel prices of the balance recharge of the advanced reactors of boiling water (A BWR) and of the advanced water at pressure reactors (EPR). (Author)

  9. Boiling water reactors with uranium-plutonium mixed oxide fuel. Report 5: Analysis of the reactivity coefficients and the stability of a BWR loaded with MOx fuel

    Energy Technology Data Exchange (ETDEWEB)

    Demaziere, C. [CEA Centre d' Etudes de Cadarache, 13 - Saint-Paul-lez-Durance (France). Direction des Reacteurs Nucleaires

    2000-01-01

    This report is a part of the project titled 'Boiling Water Reactors With Uranium-Plutonium Mixed Oxide (MOx) Fuel'. The aim of this study is to model the impact of a core loading pattern containing MOx bundles upon the main characteristics of a BWR (reactivity coefficients, stability, etc.). For this purpose, the Core Management System (CMS) codes of Studsvik Scandpower are used. This package is constituted by CASMO-4/TABLES-3/SIMULATE-3. It has been shown in previous reports that these codes are able to accurately represent and model MOx bundles. This report is thus devoted to the study of BWR cores loaded (partially or totally) with MOx bundles. The plutonium quality used is the Pu type 2016 (mostly Pu-239, 56 %, and Pu-240, 26 %), but a variation of the plutonium isotopic vector was also investigated, in case of a partial MOx loading. One notices that the reactivity coefficients do not present significant changes in comparison with a full UOx loading. Nevertheless, two main problems arise: the shutdown margin at BOC is lower than 1 % and the stability to in-phase oscillations is slightly decreased. (The SIMULATE-3 version used for this study does not contain the latest MOx enhancements described in literature, since these code developments have not been provided to the department. Nevertheless, as the nominal average enrichment of the MOx bundles is 5.41 % (total amount of plutonium), which can still be considered as a relatively low enrichment, the accuracy of the CMS codes is acceptable without the use of the MOx improvements for this level of Pu enrichment.

  10. RELAP4/MOD5: a computer program for transient thermal-hydraulic analysis of nuclear reactors and related systems. User's manual. Volume I. RELAP4/MOD5 description. [PWR and BWR

    Energy Technology Data Exchange (ETDEWEB)

    1976-09-01

    RELAP4 is a computer program written in FORTRAN IV for the digital computer analysis of nuclear reactors and related systems. It is primarily applied in the study of system transient response to postulated perturbations such as coolant loop rupture, circulation pump failure, power excursions, etc. The program was written to be used for water-cooled (PWR and BWR) reactors and can be used for scale models such as LOFT and SEMISCALE. Additional versatility extends its usefulness to related applications, such as ice condenser and containment subcompartment analysis. Specific options are available for reflood (FLOOD) analysis and for the NRC Evaluation Model.

  11. Neutron activation analysis and activity in the vessel steel of a BWR reactor for their study without radiological risks in microscopy and spectrometry; Analisis de activacion neutronica y actividad en el acero de la vasija de un reactor nuclear tipo BWR para su estudio sin riesgos radiologicos en microscopia y espectrometria

    Energy Technology Data Exchange (ETDEWEB)

    Moranchel, M.; Garcia B, A. [IPN, Escuela Superior de Fisica y Matematicas, Departamento de Fisica, Unidad Profesional Adolfo Lopez Mateos, Zacatenco, 07738 Mexico D. F. (Mexico); Longoria G, L. C., E-mail: mmoranchel@ipn.mx [IAEA, Department of Technical Cooperation, Division for Latin America, Room B1109 Wagramerstrasse 5, PO Box 100, A-1400, Vienna (Austria)

    2012-07-01

    The vessel material of nuclear reactors is subject to irradiation damage induced by the bombardment of neutrons coming from the reactor core. Neutrons are classified as fast and thermal, which produce different effects. Fast neutrons cause damage to the material by dislocation or displacement of atoms in the crystal structure, while the effect of thermal neutrons is a nuclear transmutation that can significantly change the properties of the material. The type and intensity of damage is based on the characteristics of the material, the flow of neutrons and the modes of neutrons interaction with the atomic structures of the material, among others. This work, alluding to nuclear transmutation, makes an analysis of neutron activation of all isotopes in a steel boiling water nuclear reactor (BWR) vessel. An analytical expression is obtained in order to model activity of steel, on the basis of the weight percentage of its atomic components. Its activity is theoretically estimated in a witness sample of the same material as that of the vessel, placed within the nuclear reactor since the beginning of its commercial operation in April 1995, up to August 2010. It was theoretically determined that the witness sample, with a 0.56 g mass (1 x 1 x 0.07 cm{sup 3} dimensions or equivalent) does not present a radiological risks during the stage of preparation, observation and analysis of it in electron microscopy and X-ray diffraction equipment s. The theoretical results were checked experimentally by measuring the activity of the sample by means of gamma spectrometry, measurement of the exposure levels around the sample, as well as the induced level to whole body and limbs, using thermo-luminescent dosimetry (TLD). As a result of the theoretical analysis, new chemical elements are predicted, as a result of the activation phenomena and radioactive decay, whose presence can be a fundamental factor of change in the properties of the vessel. This work is a preamble to the

  12. Determination of the neutron fluence in the welding of the 'Core shroud' of the BWR reactor core; Determinacion de la fluencia neutronica en las soldaduras del 'core shroud' del nucleo de un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Lucatero, M.A.; Xolocostli M, J.V.; Gomez T, A.M.; Palacios H, J.C. [ININ, 52750 Ocoyoacac, Estado de mexico (Mexico)]. e-mail: mal@nuclear.inin.mx

    2006-07-01

    With the purpose of defining the inspection frequency, in function of the embrittlement of the materials that compose the welding of the 'Core Shroud' or encircling of the core of a BWR type reactor, is necessary to know the neutron fluence received for this welding. In the work the calculated values of neutron fluence accumulated maxim (E > 1 MeV) during the first 8 operation cycles of the reactor are presented. The calculations were carried out according to the NRC Regulatory Guide 1.190, making use of the DORT code, which solves the transport equation in discreet ordinate in two dimensions (xy, r{theta}, and rz). The results in 3D were obtained applying the Synthesis method according to the guide before mentioned. Results are presented for the horizontal welding H3, H4, and H5, showing the corresponding curves to the fluence accumulated to the cycle 8 and a projection for the cycle 14 is presented. (Author)

  13. Design of an equilibrium nucleus of a BWR type reactor based in a Thorium-Uranium fuel; Diseno de un nucleo de equilibrio de un reactor tipo BWR basado en un combustible de Torio-Uranio

    Energy Technology Data Exchange (ETDEWEB)

    Francois, J.L.; Nunez C, A. [Laboratorio de Analisis en Ingenieria de Reactores Nucleares, Facultad de Ingenieria-UNAM, Paseo Cuauhnahuac 8532, Jiutepec, Morelos (Mexico)

    2003-07-01

    In this work the design of the reactor nucleus of boiling water using fuel of thorium-uranium is presented. Starting from an integral concept based in a type cover-seed assemble is carried out the design of an equilibrium reload for the nucleus of a reactor like that of the Laguna Verde Central and its are analyzed some of the main design variables like the cycle length, the reload fraction, the burnt fuel, the vacuum distribution, the generation of lineal heat, the margin of shutdown, as well as a first estimation of the fuel cost. The results show that it is feasible to obtain an equilibrium reload, comparable to those that are carried out in the Laguna Verde reactors, with a good behavior of those analyzed variables. The cost of the equilibrium reload designed with the thorium-uranium fuel is approximately 2% high that the uranium reload producing the same energy. It is concluded that it is convenient to include burnable poisons, type gadolinium, in the fuel with the end of improving the reload design, the fuel costs and the margin of shutdown. (Author)

  14. Thermodynamic consideration of hydrogen injection in BWR coolant. Estimation of potential for SCC control and oxidation-reduction condition of reactor coolant

    Energy Technology Data Exchange (ETDEWEB)

    Miyajima, Kaori; Hirano, Hideo; Domae, Masashi [Central Research Inst. of Electric Power Industry, Komae, Tokyo (Japan). Komae Research Lab; Kushida, H.

    2001-04-01

    Hydrogen injection into BWR coolant has been carried out in order to reduce stress corrosion cracking (SCC). It was clarified by in-plant test that SCC can be reduced under corrosion potential -0.23 V(v.s.SHE), but the theoretical basis has not been clarified. On the other hand, highly precise water quality analysis of re-circulatory-system water is generally performed. Especially, nitrogen compound changes chemical from to NO{sub 3}{sup -} -> NO{sub 2}{sup -} -> NH{sub 3}, and the NH{sub 3} becomes the cause of the increase of dose rate of the main steamy system in connection with the increase in the amount of hydrogen injection. However, the relation between this chemical form, oxidisation reduction potential, and temperature is not clear: Then, in this paper, these two points were considered by thermodynamics calculation at 25-300degC using the thermodynamics data in the high temperature accumulated in CRIEPI, and calculation results are summarized as follows; (1) the potential of the stainless steel to which the chemical form change to FeCr{sub 2}O{sub 4} from NiFe{sub 2}O{sub 4} is equilibrium is about -0.23 V at 288degC so this change is expected as one of factors for reduction of SCC, (2) the changes of chemical form of nitrogen compounds show oxidation-reduction of reactor coolant, so it can be useful as the index for control of dose rate. (author)

  15. Estimate of radiation-induced steel embrittlement in the BWR core shroud and vessel wall from reactor-grade MOX/UOX fuel for the nuclear power plant at Laguna Verde, Veracruz, Mexico

    Science.gov (United States)

    Vickers, Lisa Rene

    The government of Mexico has expressed interest to utilize the Laguna Verde boiling water reactor (BWR) nuclear power plant for the disposition of reprocessed spent uranium oxide (UOX) fuel in the form of reactor-grade mixed-oxide (MOX) fuel. MOX fuel would replace spent UOX fuel as a fraction in the core from 18--30% depending on the fuel loading cycle. MOX fuel is expected to increase the neutron fluence, flux, fuel centerline temperature, reactor core pressure, and yield higher energy neutrons. There is concern that a core with a fraction of MOX fuel (i.e., increased 239Pu wt%) would increase the radiation-induced steel embrittlement within the core shroud and vessel wall as compared to only conventional, enriched UOX fuel in the core. The evaluation of radiation-induced steel embrittlement within the core shroud and vessel wall is a concern because of the potentially adverse affect to plant and public safety, environment, and operating life of the reactor. This dissertation provides computational results of the neutron fluence, flux, energy spectrum, and radiation damage displacements per atom per second (dpa-s-1) in steel within the core shroud and vessel wall of the Laguna Verde Unit 1 BWR. The results were computed using the nuclear data processing code NJOY99 and the continuous energy Monte Carlo Neutral Particle transport code MCNP4B. The MCNP4B model of the reactor core was for maximum core loading fractions of ⅓ MOX and ⅔ UOX reactor-grade fuel in an equilibrium core. The primary conclusion of this dissertation was that the addition of the maximum fraction of ⅓ MOX fuel to the LV1 BWR core did significantly accelerate the radiation-induced steel embrittlement such that without mitigation of steel embrittlement by periodic thermal annealing or reduction in operating parameters such as, neutron fluence, core temperature and pressure, it posed a potentially adverse affect to the plant and public safety, environment, and operating life of the reactor.

  16. Reactor safety study. An assessment of accident risks in U. S. commercial nuclear power plants. Appendix VI. Calculation of reactor accident consequences. [PWR and BWR

    Energy Technology Data Exchange (ETDEWEB)

    1975-10-01

    Information is presented concerning the radioactive releases from the containment following accidents; radioactive inventory of the reactor core; atmospheric dispersion; reactor sites and meteorological data; radioactive decay and deposition from plumes; finite distance of plume travel; dosimetric models; health effects; demographic data; mitigation of radiation exposure; economic model; and calculated results with consequence model.

  17. Analysis of the microstructural evolution of the damage by neutron irradiation in the pressure vessel of a nuclear power reactor BWR; Analisis de la evolucion microestructural del dano por irradiacion neutronica en la vasija de presion de un reactor nuclear de potencia BWR

    Energy Technology Data Exchange (ETDEWEB)

    Moranchel y R, M.

    2012-07-01

    Nuclear reactor pressure vessel type BWR, installed in Mexico and in many other countries, are made of an alloy of low carbon steel. The American Society for Testing and Materials (Astm) classifies this alloy as A533-B, class 1. Both the vessel and other internal structures are continuously exposed to the neutron flux from the reactions of fission in nuclear fuel. A large number of neutrons reach the vessel and penetrate certain depth depending on their energy. Its penetration in the neutron collides with the nuclei of the atoms out of their positions in the crystal lattice of steel, producing vacancies, interstitial, segregations, among other defects, capable of affecting its mechanical properties. Analyze the micro-structural damage to the vessel due to neutron irradiation, is essential for reasons of integrity of this enclosure and safety of any nuclear power plant. The objective of this thesis work is theoretical and experimentally determine the microstructural damage of a type nuclear reactor vessel steel BWR, due to neutron radiation from the reactor core, using microscopic and spectroscopic techniques as well as Monte Carlo simulation. Microscopy Optical, Scanning Electron Microscopy, Transmission Electron Microscopy, Energy Dispersion of X-rays Spectrometry and X-rays Diffractometry were the techniques used in this research. These techniques helped in the characterization of both the basis of design of pressure vessel steel and steel irradiated, after eight years of neutron irradiation on the vessel, allowing know the surface morphology and crystal structures of the previous steel and post-irradiation, analyze the change in the microstructure of the steel vessel, morphological damage to surface level in an irradiated sample, among which are cavities in the order of microns produced by Atomic displacements due to the impact of neutronic, above all in the first layers of thickness of the vessel, the effect of swelling, regions of greater damage and Atomic

  18. 3D neutronic codes coupled with thermal-hydraulic system codes for PWR, and BWR and VVER reactors

    Energy Technology Data Exchange (ETDEWEB)

    Langenbuch, S.; Velkov, K. [GRS, Garching (Germany); Lizorkin, M. [Kurchatov-Institute, Moscow (Russian Federation)] [and others

    1997-07-01

    This paper describes the objectives of code development for coupling 3D neutronics codes with thermal-hydraulic system codes. The present status of coupling ATHLET with three 3D neutronics codes for VVER- and LWR-reactors is presented. After describing the basic features of the 3D neutronic codes BIPR-8 from Kurchatov-Institute, DYN3D from Research Center Rossendorf and QUABOX/CUBBOX from GRS, first applications of coupled codes for different transient and accident scenarios are presented. The need of further investigations is discussed.

  19. Study and characterization of noble metal deposits on similar rusty surfaces to those of the reactor U-1 type BWR of nuclear power station of Laguna Verde; Estudio y caracterizacion de depositos de metales nobles sobre superficies oxidadas similares a las del reactor de la Central de Laguna Verde (CNLV) U1 del tipo BWR

    Energy Technology Data Exchange (ETDEWEB)

    Flores S, V. H.

    2011-07-01

    In the present investigation work, were determined the parameters to simulate the conditions of internal oxidation reactor circulation pipes of the nuclear power plant of Laguna Verde in Veracruz. We used 304l stainless steel cylinders with two faces prepared with abrasive paper of No. 600, with the finality to obtain similar surface to the internal circulation piping nuclear reactor. Oxides was formed within an autoclave (Autoclave MEX-02 unit B), which is a device that simulates the working conditions of the nuclear reactor, but without radiation generated by the fission reaction within the reactor. The oxidation conditions were a temperature of 280 C and pressure of 8 MPa, similar conditions to the reactor operating in nuclear power plant of Laguna Verde in Veracruz, Mexico (BWR conditions), with an average conductivity of 4.58 ms / cm and 2352 ppb oxygen to simulate normal water chemistry NWC. Were obtained deposits of noble metal oxides formed on 304l stainless steel samples, in a 250 ml autoclave at a temperature range of 180 to 200 C. The elements that were used to deposit platinum-rhodium (Pt-Rh) with aqueous Na{sub 2}Pt (OH){sub 6} and Na{sub 3}Rh (NO{sub 2}){sub 6}, Silver (Ag) with an aqueous solution of AgNO{sub 3}, zirconium (Zr) with aqueous Zr O (NO{sub 3}) and ZrO{sub 2}, and zinc (Zn) in aqueous solution of Zn (NO{sub 3}){sub 2} under conditions of normal water chemistry. Also there was the oxidation of 304l stainless steel specimens in normal water chemistry with a solution of Zinc (Zn) (NWC + Zn). Oxidation of the specimens in water chemistry with a solution of zinc (Zn + NWC) was prepared in two ways: within the MEX-02 autoclave unit A in a solution of zinc and a flask at constant temperature in zinc solution. The oxides formed and deposits were characterized by scanning electron microscopy, energy dispersive X-ray analysis, elemental field analysis and X-ray diffraction. By other hand was evaluated the electrochemical behavior of the oxides

  20. Evaluation of the thermal-mechanical performance of fuel rods of a BWR during a power ramp using the FUELSIM code; Evaluacion del desempeno termomecanico de barras de combustible de un reactor BWR durante una rampa de potencia utilizando el codigo FUELSIM

    Energy Technology Data Exchange (ETDEWEB)

    Pantoja C, R.

    2010-07-01

    To avoid the risk to environment due to release of radioactive material, because of occurrence of an accident, it is the priority of the design and performance of the diverse systems of safety of a commercial nuclear power plant. The safety of nuclear power plants requires, therefore, monitoring those parameters having some direct or indirect effect on safety. The thermal limits are values set for those parameters considered having most impact on the safe operation of a nuclear power reactor. Some thermal limits monitoring requires the thermal-mechanical analysis of the rods containing the nuclear fuel. The fuel rod thermal-mechanical behavior under irradiation is a complex process in which there exists a great deal of interrelated physical and chemical phenomena, so that the fuel rod performance analysis in the core of a nuclear power reactor is generally accomplished by using computer codes, which integrate several of the phenomena that are expected to occur during the lifetime of the fuel rod in the core. The main application of the thermal-mechanical analysis codes is the prediction of occurrence of conditions and/or phenomena that could lead to the deterioration or even mechanical failure of the fuel rod cladding, as, for example, the pellet-cladding interaction. In the operation of a nuclear power reactor, fuel preconditioning operations refer to the operational procedures employed to reduce the fuel rod failure probability due to fuel-cladding interaction, specially during reactor startup. Preconditioning simulations are therefore necessary to determine in advance limit values for the power that can be generated in a fuel rod, and thus avoiding any rod damage. In this work, a first analysis of the thermal-mechanical performance of typical fuel rods used in nuclear reactors of the type BWR 5/6, as those two nuclear reactors in Laguna Verde, Veracruz, is performed. This study includes two types of fuel rods: one from a fuel assembly design with an array 8 x 8

  1. BWR MOX core monitoring at Kernkraftwerk Gundremmingen

    Energy Technology Data Exchange (ETDEWEB)

    Noel, Alejandro [Studsvik Scandpower (Suisse) GmbH, Nussbaumen AG (Switzerland); Holzer, Robert [NIS Ingenieurgesellschaft GmbH, Alzenau (Germany); Anton, Gerd [Studsvik Scandpower GmbH, Norderstedt (Germany); Smith, Kord [Studsvik Scandpower Inc., Idaho Falls (United States)

    2008-07-01

    The replacement of the core monitoring system for twin KWU Boiling Water Reactors (BWR) is presented. The reactors, Kernkraftwerk Gundremmingen B and C (KGG), are located in Germany. Core monitoring for KGG is more challenging than for most BWR reactors due to its core composition with about 30% MOX fuel assemblies. The objectives of this paper are to discuss the specific MOX modelling aspects in CASMO-4/Simulate-3, the impact of the MOX fuel on several core monitoring aspects like the LPRM detector modelling and to present some core monitoring results since the beginning of GARDEL's operation. The available core monitoring results confirm the accuracy of the underlying physical methods. The core monitoring system replacement att KGG was a common project of Studsvik Scandpower and NIS Ingenieurgesellschaft GmbH, where Studsvik Scandpower supplied its standard core monitoring system GARDEL and NIS was responsible for the computer hardware, system integration and plant specific add-ons. (authors)

  2. Radial distribution of UO{sub 2} and Gd{sub 2}O{sub 3} in fuel cells of a BWR Reactor; Distribucion radial de UO{sub 2} y Gd{sub 2}O{sub 3} en celdas de combustible de un reactor BWR

    Energy Technology Data Exchange (ETDEWEB)

    Montes, J.L.; Ortiz, J.J.; Perusquia del C, R. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico); Francois, J.L.; Martin del Campo M, C. [Departamento de Sistemas Energeticos, Facultad de Ingenieria, UNAM, Paseo Cuauhnahuac 8532, Jiutepec, Morelos 62500 (Mexico)]. e-mail: jlmt@nuclear.inin.mx

    2008-07-01

    The fuel system that is used at the moment in a power plant based on power reactors BWR, includes as much like the one of its substantial parts to the distribution of the fissile materials like a distribution of burnt poisons within each one of the cells which they constitute the fuel assemblies, used for the energy generation. Reason why at the beginning of a new operation cycle in a reactor of this type, the reactivity of the nucleus should be compensated by the exhaustion of the assemblies that it moves away of the nucleus for their final disposition. This compensation is given by means of the introduction of the recharge fuel, starting from the UO{sub 2} enriched in U{sup 2}35, and of the Gadolinium (Gd{sub 2}O{sub 3}). The distribution of these materials not only defines the requirements of energy generation, but in certain measures also the form in that the margins will behave to the limit them thermal during the operation of the reactor. These margins must be taken into account for the safe and efficient extraction of the energy of the fuel. In this work typical fuel cells appear that are obtained by means of the use of a emulation model of an ants colony. This model allows generating from a possible inventory of values of enrichment of U{sup 2}35, as well as of concentration of Gadolinium a typical fuel cell, which consists of an arrangement of lOxlO rods, of which 92 contain U{sup 2}35, some of these rods contain a concentration of Gd{sub 2}O{sub 3} and 8 of the total contain only water. The search of each cell finishes when the value of the Local Peak Power Factor (LPPF) in the cell reaches a minimal value, or when a pre established value of iterations is reached. The cell parameters are obtained from the results of the execution of the code HELIOS, which incorporates like a part integral of the search algorithm. (Author)

  3. Analysis of the accident at Fukushima Daiichi nuclear power plant in an A BWR reactor; Analisis del accidente de la planta nucleoelectrica de Fukushima Daiichi en un reactor tipo ABWR

    Energy Technology Data Exchange (ETDEWEB)

    Escorcia O, D. [UNAM, Facultad de Ingenieria, Ciudad Universitaria, 04510 Ciudad de Mexico (Mexico); Salazar S, E., E-mail: daniel.escorcia.ortiz@gmail.com [UNAM, Facultad de Ingenieria, Laboratorio de Analisis en Ingenieria de Reactores Nucleares, 62250 Jiutepec, Morelos (Mexico)

    2016-09-15

    The present work aims to recreate the accident occurred at the Fukushima Daiichi nuclear power plant in Japan on March 11, 2011, making use of an academic simulator of forced circulation of the A BWR reactor provided by the IAEA to know the scope of this simulator. The simulator was developed and distributed by the IAEA for academic purposes and contains the characteristics and general elements of this reactor to be able to simulate transients and failures of different types, allowing also to observe the general behavior of the reactor, as well as several phenomena and present systems in the same. Is an educational tool of great value, but it does not have a scope that allows the training of plant operators. To recreate the conditions of the Fukushima accident in the simulator, we first have to know what events led to this accident, as well as the actions taken by operators and managers to reduce the consequences of this accident; and the sequence of events that occurred during the course of the accident. Differences in the nuclear power plant behavior are observed and interpreted throughout the simulation, since the Fukushima plant technology and the simulator technology are not the same, although they have several elements in common. The Fukushima plant had an event that by far exceeded the design basis, which triggered in an accident that occurred in the first place by a total loss of power supply, followed by the loss of cooling systems, causing a level too high in temperature, melting the core and damaging the containment accordingly, allowing the escape of hydrogen and radioactive material. As a result of the simulation, was determined that the scope of the IAEA academic simulator reaches the entrance of the emergency equipment, so is able to simulate almost all the events occurred at the time of the earthquake and the arrival of the tsunami in the nuclear power plant of Fukushima Daiichi. However, due to its characteristics, is not able to simulate later

  4. Post-processor for simulations of the ORIGEN program and calculation of the composition of the activity of a burnt fuel core by a BWR type reactor; Post-procesador para simulaciones del programa ORIGEN y calculo de la composicion de la actividad de un nucleo de combustible quemado por un reactor tipo BWR

    Energy Technology Data Exchange (ETDEWEB)

    Sandoval V, S. [IIE, Av. Reforma 113, Col. Palmira, 62490 Cuernavaca, Morelos (Mexico)]. e-mail: sandoval@iie.org.mx

    2006-07-01

    The composition calculation and the activity of nuclear materials subject to processes of burnt, irradiation and decay periods are of utility for diverse activities inside the nuclear industry, as they are it: the processes design and operations that manage radioactive material, the calculation of the inventory and activity of a core of burnt nuclear fuel, for studies of type Probabilistic Safety Analysis (APS), as well as for regulation processes and licensing of nuclear facilities. ORIGEN is a program for computer that calculates the composition and the activity of nuclear materials subject to periods of burnt, irradiation and decay. ORIGEN generates a great quantity of information whose processing and analysis are laborious, and it requires thoroughness to avoid errors. The automation of the extraction, conditioning and classification of that information is of great utility for the analyst. By means of the use of the post-processor presented in this work it is facilitated, it speeds up and wide the capacity of analysis of results, since diverse consultations with several classification options and filtrate of results can be made. As illustration of the utility of the post-processor, and as an analysis of interest for itself, it is also presented in this work the composition of the activity of a burned core in a BWR type reactor according to the following classification criteria: by type of radioisotope (fission products, activation products and actinides), by specie type (gassy, volatile, semi-volatile and not volatile), by element and by chemical group. The results show that the total activity of the studied core is dominated by the fission products and for the actinides, in proportion four to one, and that the gassy and volatile species conform a fifth part of the total activity of the core. (Author)

  5. Water chemistry practice at German BWR plants

    Energy Technology Data Exchange (ETDEWEB)

    Stellwag, B. [Framatome ANP GmbH, Erlangen (Germany); Staudt, U. [VGB PowerTech e.V., Essen (Germany)

    2005-02-01

    As visual examinations carried out in 1994 detected cracks in a German boiling water reactor (BWR) plant due to intergranular stress corrosion cracking in core shroud components manufactured from Nb-stabilized CrNi steel 1.4550, safety-related assessments and in-service inspections were subsequently performed for the other six German BWRs. No cracks were found in the core shrouds of these plants. The second major event in the early 1990s was the detection of cracks at various German BWRs in piping systems made of Ti-stabilized CrNi steel 1.4541 caused by thermal sensitization in the heat-affected zone of welds. Comprehensive investigations resulted in a number of remedial measures (repair, replacement) implemented at piping in contact with reactor coolant of temperatures above 200 C. Thanks to the remedial measures and according to the analyses performed, cracking in the components in question due to the considered damage mechanisms need not be expected. German operators have therefore continued operating their BWR plants on normal water chemistry with an oxidizing environment. As a precaution, more stringent reactor coolant quality requirements have been specified and the limiting values of VGB Guideline R 401 J revised. This paper gives an overview of the trends in chemistry parameters at German BWR plants in the past 10 years. In addition, other relevant experience gained from the German BWR plants operating under normal water chemistry conditions is outlined: dose rates and collective doses, fuel performance, and results of periodic in-service inspections of major components of the reactor system. In the nearly 10 years of plant operation since implementation of the remedial measures, no cracks or other indications have been detected in any of the systems and components concerned. (orig.)

  6. Reactor safety study. An assessment of accident risks in U. S. commercial nuclear power plants. Appendices VII, VIII, IX, and X. [PWR and BWR

    Energy Technology Data Exchange (ETDEWEB)

    1975-10-01

    Information is presented concerning the release of radioactivity in reactor accidents; physical processes in reactor meltdown accidents; safety design rationale for nuclear power plants; and design adequacy.

  7. Performance of the primary containment of a BWR during a severe accident whit the code RELAP/SCDAPSIM; Comportamiento del contenedor primario de un reactor BWR durante un accidente severo con el codigo RELAP/SCDAPSIM

    Energy Technology Data Exchange (ETDEWEB)

    Castillo G, F.

    2015-07-01

    In this thesis work, it was developed a model of the vacuum breaker valves and down comers for a BWR Mark II primary containment for the code RELAP/SCDAPSIM Mod. 3.4. This code was used to simulate a Station Blackout (Sbo) that evolves to a severe accident scenario. To accomplish this task, the vacuum breaker valves and down comers were included in a simplified model of the primary containment that includes both wet well and dry well, which was coupled with a model of the Nuclear Steam Supply System (NSSS), in order to study the behavior of the primary containment during the evolution of the accident scenario. In the analysis of the results of the simulation, the behavior of the wet well and dry well during the event was particularly monitored, by analyzing the evolution of temperature and pressure profiles in such volumes, this to determine the impact of the inclusion of the breaker vacuum valves and down comers. The results show that the effect of this extension of the model is that more conservative results are obtained, i.e., higher pressures are reached in both wet well and dry well than when it is used a containment model that does not include neither the vacuum valves nor the down comers. The most relevant results obtained show that the Rcic alone is able to keep the core fully covered, but even in such a case, it evaporates about 15% of the initial inventory of liquid water in the Pressure Suppression Pool (Psp). When the Rcic operation is lost, 20% more of the liquid water inventory in the Psp is further reduced within four to twelve hours (approximately), time at which the simulation crashed. Besides, there is a significant increase of pressure in the containment. As the accident evolves, the pressure in the containment continues increasing, but there is still considerable margin to reach the design pressure of the containment. At the end of the simulation, the results show a gauge pressure value of 224,550 Pa in the Psp and 187,482 Pa in the wet well

  8. Simulation of a scenario of total loss of external and internal power (Sbo) for different vent pressures of the containment of a BWR-5; Simulacion de un escenario de perdida total de potencia externa e interna (SBO) para distintas presiones de venteo de la contencion de un reactor BWR-5

    Energy Technology Data Exchange (ETDEWEB)

    Cardenas V, J.; Mugica R, C. A.; Godinez S, V., E-mail: Jaime.cardenas@cnsns.gob.mx [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Barragan No. 779, Col. Narvarte, 03020 Mexico D. F. (Mexico)

    2014-10-15

    The simulation of a Station Black Out (Sbo) was realized with intervention of the vent containment by means of a rigid vent coming from the dry-well and that discharges directly to the atmosphere, with the MELCOR code version 2.1. This scenario was carried out for a BWR-5 and containment type Mark II, with a thermal power of 2317 MWt similar to the reactor of nuclear power plant of Laguna Verde. For this scenario was considered as only available system for coolant injection to the reactor to the Reactor Core Isolation Cooling (Rcic), which remained operating 4 hours with batteries bank. The Security and Relief Valves (SR V) were considered functional (by simplicity) and that they mechanically do not exceed their capacity to liberate pressure due to the performances in their safety way. The operator maneuver to perform the SR V and to de pressurize the vessel until the pressure (13 kg/cm{sup 2}) to operate the low pressure systems was modeled. The results cover approximately 48 hours (172000 seconds), time in which was observed the behavior of the level and pressure in the vessel. Also the scenario evolution was analyzed to different vent pressures of the primary containment (2.0, 3.0, 4.5, 6.0, and 10.0 kg/cm{sup 2}), the temperature profiles of the dry-well, the hydrogen accumulation in the containment, the radio-nuclides liberation through rigid vent to the atmosphere and the inventory of these. In this work an analysis of the pressure behavior in the primary containment is presented, with the purpose of minimizing liberated fission products to the environment. (Author)

  9. 44-BWR WASTE PACKAGE LOADING CURVE EVALUATION

    Energy Technology Data Exchange (ETDEWEB)

    J.M. Scaglione

    2004-08-25

    The objective of this calculation is to evaluate the required minimum burnup as a function of initial boiling water reactor (BWR) assembly enrichment that would permit loading of spent nuclear fuel into the 44 BWR waste package configuration as provided in Attachment IV. This calculation is an application of the methodology presented in ''Disposal Criticality Analysis Methodology Topical Report'' (YMP 2003). The scope of this calculation covers a range of enrichments from 0 through 5.0 weight percent (wt%) U-235, and a burnup range of 0 through 40 GWd/MTU. This activity supports the validation of the use of burnup credit for commercial spent nuclear fuel applications. The intended use of these results will be in establishing BWR waste package configuration loading specifications. Limitations of this evaluation are as follows: (1) The results are based on burnup credit for actinides and selected fission products as proposed in YMP (2003, Table 3-1) and referred to as the ''Principal Isotopes''. Any change to the isotope listing will have a direct impact on the results of this report. (2) The results of 100 percent of the current BWR projected waste stream being able to be disposed of in the 44-BWR waste package with Ni-Gd Alloy absorber plates is contingent upon the referenced waste stream being sufficiently similar to the waste stream received for disposal. (3) The results are based on 1.5 wt% Gd in the Ni-Gd Alloy material and having no tuff inside the waste package. If the Gd loading is reduced or a process to introduce tuff inside the waste package is defined, then this report would need to be reevaluated based on the alternative materials.

  10. Reactor safety study. An assessment of accident risks in U. S. commercial nuclear power plants. Executive summary: main report. [PWR and BWR

    Energy Technology Data Exchange (ETDEWEB)

    1975-10-01

    Information is presented concerning the objectives and organization of the reactor safety study; the basic concepts of risk; the nature of nuclear power plant accidents; risk assessment methodology; reactor accident risk; and comparison of nuclear risks to other societal risks.

  11. Simulation of a large break loss of coolant (LBLOCA), without actuation of the emergency injection systems (ECCS) for a BWR-5; Simulacion de un escenario de perdida de refrigerante grande (LBLOCA), sin actuacion de los sistemas de inyeccion de emergencia (ECCS) para un reactor BWR-5

    Energy Technology Data Exchange (ETDEWEB)

    Cardenas V, J.; Mugica R, C. A.; Lopez M, R., E-mail: jaime.cardenas@cnsns.gob.mx [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Barragan 779, Col. Narvarte, 03020 Ciudad de Mexico (Mexico)

    2015-09-15

    In this paper the analysis of scenario for the loss of coolant case was realized with break at the bottom of a recirculation loop of a BWR-5 with containment type Mark II and a thermal power of 2317 MWt considering that not have coolant injection. This in order to observe the speed of progression of the accident, the phenomenology of the scenario, the time to reach the limit pressure of containment venting and the amount of radionuclides released into the environment. This simulation was performed using the MELCOR code version 2.1. The scenario posits a break in one of the shear recirculation loops. The emergency core cooling system (ECCS) and the reactor core isolation cooling (Rcic) have not credit throughout the event, which allowed achieve greater severity on scenario. The venting of the primary containment was conducted via valve of 30 inches instead of the line of 24 inches of wet well, this in order to have a larger area of exhaust of fission products directly to the reactor building. The venting took place when the pressure in the primary containment reached the 4.5 kg/cm{sup 2} and remained open for the rest of the scenario to maximize the amount released of radionuclides to the atmosphere. The safety relief valves were considered functional they do not present mechanical failure or limit their ability to release pressure due to the large number of performances in safety mode. The results of the analysis covers about 48 hours, time at which the accident evolution was observed; behavior of level, pressure in the vessel and the fuel temperature profile was analyzed. For progression of the scenario outside the vessel, the pressure and temperature of the primary containment, level and temperature of the suppression pool, the hydrogen accumulation in the container and the radionuclides mass released into the atmosphere were analyzed. (Author)

  12. Radionuclide inventories in the discharged fuels of PHWR-220, BWR-160, VVER-1000 and the conceptual ATBR-600 reactors - A case study

    Energy Technology Data Exchange (ETDEWEB)

    Pal, Usha [Light Water Reactors Physics Section, Reactor Physics Design Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India)], E-mail: ushapal@barc.gov.in; Jagannathan, V. [Light Water Reactors Physics Section, Reactor Physics Design Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India)], E-mail: vjagan@barc.gov.in

    2008-10-15

    Radionuclides content in the discharged fuel of the conceptual thorium breeder reactor ATBR-600 has been assessed and compared against other thermal power reactors considered in Indian nuclear power programme. The contribution of actinides and the fission products inventories in the discharged fuels are separately estimated and assessed. The ATBR-600 reactor is suggested for closed fuel cycle option. The relatively large presence of the unspent plutonium would in fact be recycled. Nonetheless, the data has been presented in the event of operating ATBR-600 like other present day power reactors in a once through fuel cycle mode.

  13. Development of a computer program of fast calculation for the pre design of advanced nuclear fuel 10 x 10 for BWR type reactors; Desarrollo de un program de computo de calculo rapido para el prediseno de celdas de combustible nuclear avanzado 10 x 10 para reactores de agua en ebullicion

    Energy Technology Data Exchange (ETDEWEB)

    Perusquia, R.; Montes, J.L.; Ortiz, J.J. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: mrpc@nuclear.inin.mx

    2005-07-01

    In the National Institute of Nuclear Research (ININ) a methodology is developed to optimize the design of cells 10x10 of assemble fuels for reactors of water in boil or BWR. It was proposed a lineal calculation formula based on a coefficients matrix (of the change reason of the relative power due to changes in the enrichment of U-235) for estimate the relative powers by pin of a cell. With this it was developed the computer program of fast calculation named PreDiCeldas. The one which by means of a simple search algorithm allows to minimize the relative power peak maximum of cell or LPPF. This is achieved varying the distribution of U-235 inside the cell, maintaining in turn fixed its average enrichment. The accuracy in the estimation of the relative powers for pin is of the order from 1.9% when comparing it with results of the 'best estimate' HELIOS code. With the PreDiCeldas it was possible, at one minimum time of calculation, to re-design a reference cell diminishing the LPPF, to the beginning of the life, of 1.44 to a value of 1.31. With the cell design with low LPPF is sought to even design cycles but extensive that those reached at the moment in the BWR of the Laguna Verde Central. (Author)

  14. CFD analysis for the hydrogen transport in the primary contention of a BWR using the codes OpenFOAM and Gas-Flow; Analisis CFD para el transporte de hidrogeno en la contencion primaria de un reactor BWR usando los codigos OpenFOAM y GasFlow

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez P, D. A.

    2014-07-01

    using a limited number of semi-empirical data, and instead, mathematical relationships are used taking into account the various physical phenomena as well the interactions that occur among them, such as heat transfer between the fluid and the solid walls condensation of water vapor on the walls, the turbulent effects in areas of restricted passage, etc. Taking into account these advantages, this study presents a qualitative and quantitative comparison between the CFD codes OpenFOAM and Gas-Flow related to the transport phenomena of Hydrogen and other gases in the primary containment of a BWR reactor. Gas-Flow is a code of commercial license that is well validated, developed in Germany to analyze the transport of gases in nuclear reactor containments. On the other hand, OpenFOAM is an open source CFD code offering several solvers for different phenomena assessments, in this work, the reacting Foam solver is used because it has a strong similarity to the intended application of Hydrogen transport. In this thesis the results obtained using the reacting Foam solver of OpenFOAM for the calculation of transport of Hydrogen are compared with the results of the Gas-Flow code in order to assess if it is feasible to use the open source code OpenFOAM in the case of Hydrogen transport in primary containment of a BWR reactor. Some differences in the qualitative and quantitative results from both codes were found, the differences (with a maximum error rate of 4%) in the quantitative results were found are small and are considered more than acceptable for this type of analysis, moreover, these differences are mainly attributed to the transport models used, mainly because OpenFOAM uses a homogeneous mixture model and Gas-Flow a heterogeneous one. Implementing appropriate solvers in codes like OpenFOAM has the goal to develop own tools that are applicable to the transport of Hydrogen in the primary containment of a BWR reactor and thus, to gain some independence while not relying on

  15. A BWR licensing experience in the USA

    Energy Technology Data Exchange (ETDEWEB)

    Powers, J.; Ogura, C. [Toshiba America Nuclear Energy, Charlotte, North Carolina (United States); Arai, K. [Toshiba Corporation, Yokohama, Kanagawa (Japan); Thomas, S.; Mookhoek, B., E-mail: jim.powers@toshiba.com [Nuclear Innovation North America, Lake Jackson, Texas (United States)

    2015-09-15

    The US-Advanced Boiling Water Reactor (A BWR), certified by the United States Nuclear Regulatory Commission (US NRC), is a third generation, evolutionary boiling water reactor design which is the reference for the South Texas Project Units 3 and 4 (STP3-4) Combined License Application (Cola). Nuclear Innovation North America (Nina) is the License Applicant for this new build project, and Toshiba is the selected primary technology contractor. The STP3-4 project has finished the US NRC technical review of the Cola through the final meeting of the Advisory Committee on Reactor Safeguards (ACRS), and the Final Safety Evaluation Report (FSER) is scheduled to be issued by the US NRC in the middle of 2015. The next steps are to support the Mandatory Hearing process, and voting by the NRC commissioners on the motion to grant the Combined License, which is scheduled beginning of 2016 according to US NRC schedule as of March 30, 2015. This paper summarizes the history and progress of the US-A BWR licensing, including the experiences of the Licensee, Nina, and Toshiba as the Epc team worked through the Code of Federal Regulations Title 10 (10-Cfr) Part 52 process, and provides some perspectives on how the related licensing material would also be of value within a 10-Cfr Part 50, two-step process to minimize schedule and financial risks which could arise from ongoing technical developments and regulatory reviews. (Author)

  16. BWR ASSEMBLY SOURCE TERMS FOR WASTE PACKAGE DESIGN

    Energy Technology Data Exchange (ETDEWEB)

    T.L. Lotz

    1997-02-15

    This analysis is prepared by the Mined Geologic Disposal System (MGDS) Waste Package Development Department (WPDD) to provide boiling water reactor (BWR) assembly radiation source term data for use during Waste Package (WP) design. The BWR assembly radiation source terms are to be used for evaluation of radiolysis effects at the WP surface, and for personnel shielding requirements during assembly or WP handling operations. The objectives of this evaluation are to generate BWR assembly radiation source terms that bound selected groupings of BWR assemblies, with regard to assembly average burnup and cooling time, which comprise the anticipated MGDS BWR commercial spent nuclear fuel (SNF) waste stream. The source term data is to be provided in a form which can easily be utilized in subsequent shielding/radiation dose calculations. Since these calculations may also be used for Total System Performance Assessment (TSPA), with appropriate justification provided by TSPA, or radionuclide release rate analysis, the grams of each element and additional cooling times out to 25 years will also be calculated and the data included in the output files.

  17. Safety analysis of thorium-based fuels in the General Electric Standard BWR

    Energy Technology Data Exchange (ETDEWEB)

    Colby, M.J.; Townsend, D.B.; Kunz, C.L.

    1980-06-01

    A denatured (U-233/Th)O/sub 2/ fuel assembly has been designed which is energy equivalent to and hardware interchangeable with a modern boiling water reactor (BWR) reference reload assembly. Relative to the reference UO/sub 2/ fuel, the thorium fuel design shows better performance during normal and transient reactor operation for the BWR/6 product line and will meet or exceed current safety and licensing criteria. Power distributions are flattened and thermal operating margins are increased by reduced steam void reactivity coefficients caused by U-233. However, a (U-233/Th)O/sub 2/-fueled BWR will likely have reduced operating flexibility. A (U-235/Th)O/sub 2/-fueled BWR should perform similar to a UO/sub 2/-fueled BWR under all operating conditions. A (Pu/Th)O/sub 2/-fueled BWR may have reduced thermal margins and similar accident response and be less stable than a UO/sub 2/-fueled BWR. The assessment is based on comparisions of point model and infinite lattice predictions of various nuclear reactivity parameters, including void reactivity coefficients, Doppler reactivity coefficients, and control blade worths.

  18. RELAP4/MOD5: a computer program for transient thermal-hydraulic analysis of nuclear reactors and related systems. User's manual. Volume III. Checkout applications. [PWR and BWR

    Energy Technology Data Exchange (ETDEWEB)

    Obenchain, C. F.; Ramsthaler, J. H.; Eales, E. P.; Charlton, T. R.; Childs, F. W.; Giles, M. M.; Good, E. G.; Gruen, G. E.; Guttman, J.; Johnsen, G. W.; Katsma, K. R.; Keeler, C. D.; Lawford, T. W.; Mohr, C. M.; Singer, G. L.; Townsend, W. C.

    1976-09-01

    Checkout problems presented include the following: PWR large cold leg break; PWR small cold leg break; PWR intermediate sized cold leg break; BWR large recirculation line break; BWR small recirculation line break; INEL Semiscale small cold leg break; INEL LOFT large cold leg break and INEL Semiscale large cold leg break. Also included is Update 2 of the RELAP 4/M0D5 code.

  19. Evaluation of the fuel rod integrity in PWR reactors from the spectrometric analysis of the primary coolant; Avaliacao da integridade de varetas combustiveis em reatores PWR a partir da analise espectrometrica da agua do primario

    Energy Technology Data Exchange (ETDEWEB)

    Monteiro, Iara Arraes

    1999-02-15

    The main objective of this thesis is to provide a better comprehension of the phenomena involved in the transport of fission products, from the fuel rod to the coolant of a PWR reactor. To achieve this purpose, several steps were followed. Firstly, it was presented a description of the fuel elements and the main mechanisms of fuel rod failure, indicating the most important nuclides and their transport mechanisms. Secondly, taking both the kinetic and diffusion models for the transport of fission products as a basis, a simple analytical and semi-empirical model was developed. This model was also based on theoretical considerations and measurements of coolant's activity, according to internationally adopted methodologies. Several factors are considered in the modelling procedures: intrinsic factors to the reactor itself, factors which depend on the reactor's operational mode, isotope characteristic factors, and factors which depend on the type of rod failure. The model was applied for different reactor's operational parameters in the presence of failed rods. The main conclusions drawn from the analysis of the model's output are relative to the variation on the coolant's water activity with the fuel burnup, the linear operation power and the primary purification rate and to the different behaviour of iodine and noble gases. The model was saturated from a certain failure size and showed to be unable to distinguish between a single big fail and many small ones. (author)

  20. Advanced methods for BWR transient and stability analysis

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, A.; Wehle, F.; Opel, S.; Velten, R. [AREVA, AREVA NP, Erlangen (Germany)

    2008-07-01

    The design of advanced Boiling Water Reactor (BWR) fuel assemblies and cores is governed by the basic requirement of safe, reliable and flexible reactor operation with optimal fuel utilization. AREVA NP's comprehensive steady state and transient BWR methodology allows the designer to respond quickly and effectively to customer needs. AREVA NP uses S-RELAP5/RAMONA as the appropriate methodology for the representation of the entire plant. The 3D neutron kinetics and thermal-hydraulics code has been developed for the prediction of system, fuel and core behavior and provides additional margins for normal operation and transients. Of major importance is the extensive validation of the methodology. The validation is based on measurements at AREVA NP's test facilities, and comparison of the predictions with a great wealth of measured data gathered from BWR plants during many years of operation. Three of the main fields of interest are stability analysis, operational transients and reactivity initiated accidents (RIAs). The introduced 3D methodology for operational transients shows significant margin regarding the operational limit of critical power ratio, which has been approved by the German licensing authority. Regarding BWR stability a large number of measurements at different plants under various conditions have been performed and successfully post-calculated with RAMONA. This is the basis of reliable pre-calculations of the locations of regional and core-wide stability boundaries. (authors)

  1. RAMONA analysis of BWR stability at nuclear power plant Brunsbuettel

    Energy Technology Data Exchange (ETDEWEB)

    Kappes, C.; Velten, R.; Wehle, F. [AREVA NP GmbH, Erlangen (Germany); Huettmann, A.; Schuster, R. [Vattenfall Europe GmbH, Hamburg (Germany)

    2010-05-15

    For high power/low flow operating conditions associated with unfavorable core power distributions, BWR operation requires attention with respect to potential power and flow oscillations. Beside stability analyses based on highly validated methodology as RAMONA, also stability measurements are performed in BWR plants. Such measurements usually cover the evaluation of Average Power Range Monitor (APRM) and Local Power Range Monitor (LPRM) signals of the BWR core at several operating conditions. This paper presents the numerical simulation of stability phenomena which were recorded in the frame of a stability measurement at the nuclear power plant Brunsbuettel (KKB) on December 12{sup th} 2004 (Cycle 18). The measurement showed a local instability at most investigated operating points and a temporal global instability when the reactor was operated at conditions where four of the eight recirculation pumps were running. The numerical investigation with RAMONA-3 focuses on the operating point with four recirculation pumps when a temporal global instability has been measured. It will be shown that a local destabilization of a single Fuel Assembly (FA) can yield a global instability mode when the reactor is operating under high power and low flow conditions. Such phenomena have already been observed and analyzed for other BWR plants as e.g. Forsmark-1. (orig.)

  2. LBB application in Swedish BWR design

    Energy Technology Data Exchange (ETDEWEB)

    Kornfeldt, H.; Bjoerk, K.O.; Ekstroem, P. [ABB Atom, Vaesteras (Sweden)

    1997-04-01

    The protection against dynamic effects in connection with potential pipe breaks has been implemented in different ways in the development of BWR reactor designs. First-generation plant designs reflect code requirements in effect at that time which means that no piping restraint systems were designed and built into those plants. Modern designs have, in contrast, implemented full protection against damage in connection with postulated pipe breaks, as required in current codes and regulations. Moderns standards and current regulatory demands can be met for the older plants by backfitting pipe whip restraint hardware. This could lead to several practical difficulties as these installations were not anticipated in the original plant design and layout. Meeting the new demands by analysis would in this situation have great advantages. Application of leak-before-break criteria gives an alternative opportunity of meeting modem standards in reactor safety design. Analysis takes into account data specific to BWR primary system operation, actual pipe material properties, piping loads and leak detection capability. Special attention must be given to ensure that the data used reflects actual plant conditions.

  3. Thermohydraulic stability coupled to the neutronic in a BWR; Estabilidad termohidraulica acoplada a la neutronica en un BWR

    Energy Technology Data Exchange (ETDEWEB)

    Calleros M, G.; Zapata Y, M.; Gomez H, R.A.; Mendez M, A. [Comision Federal de Electricidad, Central Nucleoelectrica de Laguna Verde, Carretera Cardel-Nautla Km. 42.5, Mpio. Alto Lucero, Veracruz (Mexico); Castlllo D, R. [ININ, Carretera Mexico-Toluca Km 36.5, La Marquesa, Estado de Mexico (Mexico)]. e-mail: gcm9acpp@cfe.gob.mx

    2006-07-01

    In a BWR type reactor the phenomenon of the nuclear fission is presented, in which are liberated in stochastic form neutrons, originating that the population of the same ones varies in statistic form around a mean value. This variation will cause that when the neutron flow impacts on the neutron detectors, its are had as a result neutron flow signals with fluctuations around an average value. In this article it is shown that it conforms it lapses the time, this variations in the neutron flow (and therefore, in the flow signal due only to the fission), they presented oscillations inside a stable range, which won't be divergent. Considering that the BWR is characterized because boiling phenomena are presented, which affect the moderation of the neutrons, additional variations will be had in the signal coming from the neutron detectors, with relationship to the fission itself, which will be influenced by the feedback of the moderator's reactivity and of the temperature of the fuel pellet. Also, as the BWR it has coupled control systems to maintain the coolant level one and of the thermal power of the reactor, for each control action it was affected the neutron population. This means that the reactor could end up straying of a stable state condition. By it previously described, the study of the thermohydraulic stability coupled to the neutronic is complex. In this work it is shown the phenomenology, the mathematical models and the theoretical behavior associated to the stability of the BWR type reactor; the variables that affect it are identified, the models that reproduce the behavior of the thermohydraulic stability coupled to the neutronic, the way to maintain stable the reactor and the instrumentation that can settle to detect and to suppress uncertainties is described. In particular, is make reference to the evolution of the methods to maintain the stability of the reactor and the detection system and suppression of uncertainties implemented in the

  4. Contenido del derecho a la integridad personal

    OpenAIRE

    Javier Alfonso Galindo

    2009-01-01

    El derecho a la integridad personal ha sido previsto en múltiples documentos internacionales y ha sido reconocido en el ámbito internacional como un derecho fundamental. Con respecto de este derecho en particular, existe un vacío sobre ciertos aspectos en la determinación de la totalidad de las normas jurídicas aplicables. Se pretende, entonces, crear una herramienta que contenga las diferentes interpretaciones y decisiones emitidas por los distintos organismos internacionales especializados ...

  5. Contenido del derecho a la integridad personal

    Directory of Open Access Journals (Sweden)

    Javier Alfonso Galindo

    2009-12-01

    Full Text Available El derecho a la integridad personal ha sido previsto en múltiples documentos internacionales y ha sido reconocido en el ámbito internacional como un derecho fundamental. Con respecto de este derecho en particular, existe un vacío sobre ciertos aspectos en la determinación de la totalidad de las normas jurídicas aplicables. Se pretende, entonces, crear una herramienta que contenga las diferentes interpretaciones y decisiones emitidas por los distintos organismos internacionales especializados en esta materia tanto en el sistema universal como en el sistema regional de protección de los derechos humanos, para de esta manera crear un corpus jurisprudencial y doctrinal sobre algunos vacíos conceptuales existentes en la actualidad sobre este tema. De igual forma, se pretende aclarar e interpretar lo que se conoce como integridad física, psíquica y moral dentro del derecho a la integridad personal. Es por ello por lo que el objetivo primordial radica en determinar el contenido del derecho a la integridad personal; a tal fin, se recopiló información evaluada conforme a la técnica de análisis de contenido y una vez construida la matriz correspondiente para facilitar el empleo de métodos de inducción, deducción, interpretación correcta de las normas jurídicas internacionales y la construcción argumental de las ideas, se logró obtener las conclusiones correspondientes.

  6. Development of BWR regional stability experimental facility SIRIUS-F, which simulates thermal-hydraulics-neutronics coupling in reactor core, and stability evaluation of ABWR

    Energy Technology Data Exchange (ETDEWEB)

    Masahiro Furuya; Fumio Inada [Central Research Institute of Electric Power Industry (CRIEPI) 2-11-1 Iwado-kita, Komae, Tokyo 201-8511 (Japan); Takanori Fukahori [Global Nuclear Fuel Japan (GNF-J) 2-3-1 Uchikawa, Yokosuka, Kanagawa 239-0836 (Japan); Shinya Mizokami [Tokyo Electric Power Company (TEPCO) 1-1-3 Uchisaiwai-cho, Chiyoda, Tokyo 100-0011 (Japan)

    2005-07-01

    Full text of publication follows: The SIRIUS-F facility was designed and constructed for highly accurate simulation of channel, core-wide and regional instabilities of an ABWR. A real-time simulation is performed for the modal-point kinetics of reactor neutronics and fuel-rod conduction on the basis of a measured void fraction in a reactor core section of the facility. A noise analysis method was performed to calculate decay ratios from dominant poles of transfer function on the basis of the AR method by applying time series of a core inlet flow rate. By utilizing this method, one can estimate stability at any specific operating point online without assuming excess conservative conditions. Channel and regional stability experiments were conducted for a wide range of operating conditions including maximum power points along the minimum pump speed line and the natural circulation line of the ABWR. The decay ratios and the resonance frequencies are in good agreement with those from the design analysis code, ODYSY. The SIRIUS-F experimental results demonstrated stability characteristics such as a stabilizing effect of the power, and reviled a sufficiently large stability margin even under hypothetical conditions of power enlargement. (authors)

  7. BWR Refill-Reflood Program, Task 4. 7 - model development: basic models for the BWR version of TRAC

    Energy Technology Data Exchange (ETDEWEB)

    Andersen, J G.M.; Chu, K H; Shaug, J C

    1983-09-01

    TRAC (Transient Reactor Analysis Code) is a computer code for best estimate analysis of the thermal hydraulic conditions in a reactor system. The constitutive correlations for shear and heat transfer developed for the Boiling Water Reactor (BWR) version of TRAC are described. A universal flow regime map has been developed to tie the regimes for shear and heat transfer into a consistent package. New models in the areas of interfacial shear, interfacial heat transfer and thermal radiation have been introduced. Improvements have also been made to the constitutive correlations and the numerical methods. All the models have been implemented into the GE version TRACB02 and extensively tested against data.

  8. Integrity assessment of research reactor fuel cladding and material testing using eddy current inspection; Avaliacao de integridade de revestimentos de combustiveis de reatores de pesquisa e teste de materiais utilizando o ensaio de correntes parasitas

    Energy Technology Data Exchange (ETDEWEB)

    Alencar, Donizete Anderson de

    2004-07-01

    A methodology to perform the integrity assessment of research reactors nuclear fuels cladding, such as those installed in IPR-Rl (TRIGA) and IEA-R1 (MTR), using nondestructive electromagnetic inspection (eddy current) is presented. This methodology is constituted by: the development of calibration reference standards, specific for each type of fuel; the development of special test probes; the recommendations for the inspection equipment calibration; the construction of voltage based evaluation curves and the inspection procedures developed for the characterization of detected flaws. The test probes development, specially those designed for the inspection of MTR fuels cladding, which present access difficulties due to the narrow gap between fuel plates (2,89 mm for IEAR-R1), constituted a challenge that demanded the introduction of unusual materials and constructive techniques. The operational performance of the developed resources, as well as the special operative characteristics of the test probes, such as their immunity to adjacent fuel plates interference and electrical resistivity changes of the fuels meat are experimentally demonstrated. The practical applicability of the developed methodology is verified in non radioactive environment, using a dummy MTR fuel element model, similar to an IEA-R1 reactor fuel element, produced and installed in IPEN, Sao Paulo. The efficacy of the proposed methodology was verified by the achieved results. (author)

  9. LAPUR5. BWR Core Stability Measurements

    Energy Technology Data Exchange (ETDEWEB)

    March-Leuba, J.; Otaduy, P.J. [Oak Ridge National Lab., TN (United States)

    1990-01-01

    LAPUR5 is a mathematical description of the core of a boiling water reactor (BWR). The program uses a point kinetics description of the neutron dynamics together with a distributed-parameter model of the core thermal hydrodynamics to produce a space-dependent representation of the dynamics of a BWR in the frequency domain for small perturbations about a steady-state condition. LAPUR5 consists of two autonomous modules, LAPUR5X, the steady-state module, and LAPUR5W the dynamics module, which are linked by use of an intermediate storage device. LAPUR5X solves the coolant and the fuel steady-state governing equations while LAPUR5W solves the dynamic equations for the coolant, fuel, and neutron field in the frequency domain. Considerable detail exists in the modeling of the thermohydrodynamics and the reactivity feedbacks. LAPUR5 can be run interactively (LAPUR) or in batch mode (BLAPUR); these are equivalent except that LAPUR allows the user to edit input parameters at run time. Both spawn the two autonomous modules consecutively and delete the intermediate storage files.

  10. Simulation of the aspersion system of the core low pressure (LPCS) for a boiling water reactor (BWR) based on RELAP; Simulacion del sistema de aspersion del nucleo a baja presion (LPCS) para un reactor de agua en ebullicion (BWR) basado en RELAP

    Energy Technology Data Exchange (ETDEWEB)

    Membrillo G, O. E.; Chavez M, C., E-mail: garzo1012@gmail.com [UNAM, Facultad de Ingenieria, Circuito Interior, Ciudad Universitaria, 04510 Mexico D. F. (Mexico)

    2012-10-15

    The present work presents the modeling and simulation of the aspersion system to low pressure of reactor of the nuclear power plant of Laguna Verde using the nuclear code RELAP/SCDAP. The objective of the emergency systems inside a nuclear reactor is the cooling of the core, nor caring the performance of any other emergency system in the case of an accident design base for coolant loss. To obtain a simulation of the system is necessary to have a model based on their main components, pipes, pumps, valves, etc. This article describes the model for the simulation of the main line and the test line for the HPCS. At the moment we have the simulation of the reactor vessel and their systems associated to the nuclear power plant of Laguna Verde, this work will allow to associate the emergency system model LPCS to the vessel model. The simulation of the vessel and the emergency systems will allow knowing the behavior of the reactor in the stage of the coolant loos, giving the possibility to analyze diverse scenarios. The general model will provide an auxiliary tool for the training in classroom and at distance in the operation of nuclear power plants. (Author)

  11. Time-domain analysis of BWR core stability

    Energy Technology Data Exchange (ETDEWEB)

    Yokomizo, Osamu

    1983-01-01

    A time-domain stability analysis program for boiling water nuclear reactors (BWRs) has been developed and applied to analysis of a commercial size BWR. The program takes into account parallel channel effects. The model incorporates (a) one point neutron kinetics with weighted average reactivity feedback, (b) radial heat conduction and transfer in fuel rods, (c) fuel channel thermal hydraulics with quasi-equilibrium subcooled boiling approximation, and (d) recirculation hydrodynamics. Nonlinearity and parallel channel effects are examined through analyses of a commercial size BWR. Core behavior has been found virtually linear for small but finite amplitude oscillations, which proved the validity of frequency-domain stability analyses for finite disturbances. It has also been found that single channel analyses with core averaged thermal hydraulic properties give more stable results than parallel channel analyses.

  12. An A BWR demonstration simulator for training and developing technical staff

    Energy Technology Data Exchange (ETDEWEB)

    Powers, J. [Toshiba America Nuclear Energy, Charlotte, North Carolina (United States); Yonezawa, H.; Aoyagi, Y.; Kataoka, K., E-mail: jim.powers@toshiba.com [Toshiba Corporation, Kawasaki, Kanagawa (Japan)

    2015-09-15

    The US-Advanced Boiling Water Reactor (A BWR), certified by the US NRC, is a third generation, evolutionary boiling water reactor design which is the reference for the South Texas Project Units 3 and 4 (STP3-4) Combined License Application (Cola). Nuclear Innovation North America (Nina) is the License Applicant for this new build project, and Toshiba is the selected primary technology contractor. Toshiba has developed a Demonstration Simulator of the A BWR control room that provides a realistic experience for training and education on BWR principles and operations fundamentals. The Demonstration Simulator is located in the Toshiba America Nuclear Energy (Tane) office in Charlotte, North Carolina and is composed of standard office computer equipment set up in a specific arrangement that is representative of the layout of an A BWR control room. The Demonstration Simulator is not intended for licensed operator training, but can provide a framework for encouraging entry level technically oriented nuclear workers to enter the operations field; strengthening the linkage between university energy field curricula and real-life application of theory; and, improving understanding of integrated plant operations for developing station technical staff. This paper describes the A BWR Demonstration Simulator and its applications for training and educating future nuclear workers. (Author)

  13. Hydrogen injection in BWR and related radiation chemistry

    Science.gov (United States)

    Ishigure, Kenkichi; Takagi, Junichi; Shiraishi, Hirotsugu

    Hydrogen injection to feed water systems in boiling water reactors (BWR) has drawn wide attention as one of the possible countermeasures to the stress corrosion cracking (SCC) of 304 type stainless steel piping. To confirm the effectiveness of the hydrogen injection, a computer simulation of the complicated radiolysis reactions was carried out. The result of the simulation showed that the reactor water data monitored at the usual sampling points in actual plants reflect mainly the reactions in the downcomer portion but not in the reactor core in BWR. The calculation claimed approximately 300 ppb hydrogen in feed water to reduce the oxygen concentration in the recirculation lines to a negligible level, while one order of magnitude higher level of hydrogen is necessary to suppress oxygen in the reactor core. The computer simulation requires many radiation chemical data as in-put, among which are G values of initial products for water radiolysis at high temperature. An experimental approach was made to confirm the G values for high temperature radiolysis of water. The result does not seem to be consistent with the high temperature G values reported by Burns.

  14. Simulation of the aspersion system of the core at high pressure (HPCS) for a boiling water reactor (BWR) based on RELAP; Simulacion del sistema de aspersion del nucleo alta presion (HPCS) para un reactor de agua en ebullicion (BWR) basado en RELAP

    Energy Technology Data Exchange (ETDEWEB)

    Vargas O, D.; Chavez M, C., E-mail: danmirnyi@gmail.com [UNAM, Facultad de Ingenieria, Circuito Interior, Ciudad Universitaria, 04510 Mexico D. F. (Mexico)

    2012-10-15

    A high-priority topic for the nuclear industry is the safety, consequently a nuclear power plant should have the emergency systems of cooling of the core (ECCS), designed exclusively to enter in operation in the event of an accident with coolant loss, including the design base accident. The objective of the aspersion system of the core at high pressure (HPCS) is to provide in an autonomous way the cooling to the core maintaining for if same the coolant inventory even when a small break is presented that does not allow the depressurization of the reactor and also avoiding excessive temperatures that affect the shielding of the fuel. The present work describes the development of the model and the simulation of the HPCS using the RELAP/SCDAP code. During the process simulation, for the setting in march of the system HPCS in an accident with coolant loss is necessary to implement the main components of the system taking into account what unites them, the main pump, the filled pump, the suction and injection valves, pipes and its water sources that can be condensed storage tanks and the suppression pool. The simulation of this system will complement the model with which counts the Analysis Laboratory in Nuclear Reactors Engineering of the UNAM regarding to the nuclear power plant of Laguna Verde which does not have a detailed simulation of the emergency cooling systems. (Author)

  15. Statistical analysis in the design of nuclear fuel cells and training of a neural network to predict safety parameters for reactors BWR; Analisis estadistico en el diseno de celdas de combustible nuclear y entrenamiento de una red neuronal para predecir parametros de seguridad para reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Jauregui Ch, V.

    2013-07-01

    In this work the obtained results for a statistical analysis are shown, with the purpose of studying the performance of the fuel lattice, taking into account the frequency of the pins that were used. For this objective, different statistical distributions were used; one approximately to normal, another type X{sup 2} but in an inverse form and a random distribution. Also, the prediction of some parameters of the nuclear reactor in a fuel reload was made through a neuronal network, which was trained. The statistical analysis was made using the parameters of the fuel lattice, which was generated through three heuristic techniques: Ant Colony Optimization System, Neuronal Networks and a hybrid among Scatter Search and Path Re linking. The behavior of the local power peak factor was revised in the fuel lattice with the use of different frequencies of enrichment uranium pines, using the three techniques mentioned before, in the same way the infinite multiplication factor of neutrons was analyzed (k..), to determine within what range this factor in the reactor is. Taking into account all the information, which was obtained through the statistical analysis, a neuronal network was trained; that will help to predict the behavior of some parameters of the nuclear reactor, considering a fixed fuel reload with their respective control rods pattern. In the same way, the quality of the training was evaluated using different fuel lattices. The neuronal network learned to predict the next parameters: Shutdown Margin (SDM), the pin burn peaks for two different fuel batches, Thermal Limits and the Effective Neutron Multiplication Factor (k{sup eff}). The results show that the fuel lattices in which the frequency, which the inverted form of the X{sup 2} distribution, was used revealed the best values of local power peak factor. Additionally it is shown that the performance of a fuel lattice could be enhanced controlling the frequency of the uranium enrichment rods and the variety of

  16. Installation of a new type of nuclear reactor in Mexico: advantages and disadvantages; Instalacion de un nuevo tipo de reactor nuclear en Mexico: ventajas y desventajas

    Energy Technology Data Exchange (ETDEWEB)

    Jurado P, M.; Martin del Campo M, C. [FI-UNAM, 04510 Mexico D.F. (Mexico)]. e-mail: mjp_green@hotmail.com

    2005-07-01

    In this work the main advantages and disadvantages of the installation of a new type of nuclear reactor different to the BWR type reactor in Mexico are presented. A revision of the advanced reactors is made that are at the moment in operation and of the advanced reactors that are in construction or one has already planned its construction in the short term. Specifically the A BWR and EPR reactors are analyzed. (Author)

  17. Reduction of radiation exposure in Japanese BWR Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Morikawa, Yoshitake [ISOGO Nuclear Engineering Center, Yokohama (Japan)

    1995-03-01

    The reduction of occupational exposure to radiation during the annual inspection and maintenance outages of Japanese boiling water reactors (BWR) is one of the most important objectives for stable and reliable operation. It was shown that this radiation exposure is caused by radionuclides, such as Co-60, Co-58 and Mn-54 which are produced from the metal elements Co, Ni, and Fe present in the corrosion products of structural materials that had been irradiated by neutrons. Therefore, to reduce radiation sources and exposures in Japanese BWRs, attempts have been reinforced to remove corrosion products and activated corrosion products from the primary coolant system. This paper describes the progress of the application of these measures to Japanese BWRs. Most Japanese BWR-4 and BWR-5 type nuclear power plants started their commercial operations during the 1970s. With the elapse of time during operations, a problem came to the forefront, namely that occupational radiation exposure during plant outages gradually increased, which obstructed the smooth running of inspections and maintenance work. To overcome this problem, extensive studies to derive effective countermeasures for radiation exposure reduction were undertaken, based on the evaluation of the plants operation data.

  18. Determination of BWR Spent Nuclear Fuel Assembly Effective Thermal Conductivity

    Energy Technology Data Exchange (ETDEWEB)

    Matthew D. Hinds

    2001-10-17

    The purpose of this calculation is to provide an effective thermal conductivity for use in predicting peak cladding temperatures in boiling water reactor (BWR) fuel assemblies with 7x7,8x8, and 9x9 rod arrays. The first objective of this calculation is to describe the development and application of a finite element representation that predicts peak spent nuclear fuel temperatures for BWR assemblies. The second objective is to use the discrete representation to develop a basis for determining an effective thermal conductivity (described later) for a BWR assembly with srneared/homogeneous properties and to investigate the thermal behavior of a spent fuel assembly. The scope of this calculation is limited to a steady-state two-dimensional representation of the waste package interior region. This calculation is subject to procedure AP-3.124, Calculations (Ref. 27) and guided by the applicable technical work plan (Ref. 14). While these evaluations were originally developed for the thermal analysis of conceptual waste package designs emplaced in the potential repository at Yucca Mountain, the methodology applies to storage and transportation thermal analyses as well. Note that the waste package sketch in Attachment V depicts a preliminary design, and should not be interpreted otherwise.

  19. Simulation of the injection system of cooling water to low pressure (Lpci) for a boiling water reactor (BWR) based on RELAP; Simulacion del sistema de inyeccion de agua de refrigeracion a baja presion (LPCI) para un reactor de agua en ebullicion (BWR) basado en RELAP

    Energy Technology Data Exchange (ETDEWEB)

    Delgado C, R. A.; Lopez S, E.; Chavez M, C., E-mail: renedelgado2015@hotmail.com [UNAM, Facultad de Ingenieria, Circuito Interior, Ciudad Universitaria, 04510 Mexico D. F. (Mexico)

    2012-10-15

    The present article describes the modeling and simulation of the Injection System of Cooling Water to Low Pressure (Lpci) for the nuclear power plant of Laguna Verde. Is very important to be able to predict the behavior of the nuclear plant in the case of an emergency stop, and while nearer to the reality are the results of a simulation, better is the safety protocol that can be devised. In the Engineering Faculty of the UNAM at the present is had logical models of the safety systems, but due to the nature of the same, these simulations do not provide of the quantity of enough information to be able to reproduce with more accuracy the behavior of the Lpci in the case of a severe accident. For this reason, the RELAP code was used for the flows modeling, components and structures of heat transfers in relation to the system Lpci. The modeling of the components is carried out with base on technical information of the nuclear plant and the results will be corroborated with information in reference documents as the Rasp (the Reactor analysis support package) and the Fsar (Final safety analysis report) for the nuclear power plant of Laguna Verde. (Author)

  20. Effect of Control Blade History, and Axial Coolant Density and Burnup Profiles on BWR Burnup Credit

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, William BJ J [ORNL

    2016-01-01

    A technical basis for peak reactivity boiling water reactor (BWR) burnup credit (BUC) methods was recently generated, and the technical basis for extended BWR BUC is now being developed. In this paper, a number of effects related to extended BWR BUC are analyzed, including three major operational effects in BWRs: the coolant density axial distribution, the use of control blades during operation, and the axial burnup profile. Specifically, uniform axial moderator density profiles are analyzed and compared to previous results and an additional temporal fidelity study combing moderator density profiles for three different fuel assemblies is presented. Realistic control blade histories and cask criticality results are compared to previously generated constructed control blade histories. Finally, a preliminary study of the axial burnup profile is provided.

  1. Key Parameters for Operator Diagnosis of BWR Plant Condition during a Severe Accident

    Energy Technology Data Exchange (ETDEWEB)

    Clayton, Dwight A [ORNL; Poore III, Willis P [ORNL

    2015-01-01

    The objective of this research is to examine the key information needed from nuclear power plant instrumentation to guide severe accident management and mitigation for boiling water reactor (BWR) designs (specifically, a BWR/4-Mark I), estimate environmental conditions that the instrumentation will experience during a severe accident, and identify potential gaps in existing instrumentation that may require further research and development. This report notes the key parameters that instrumentation needs to measure to help operators respond to severe accidents. A follow-up report will assess severe accident environmental conditions as estimated by severe accident simulation model analysis for a specific US BWR/4-Mark I plant for those instrumentation systems considered most important for accident management purposes.

  2. BWR Source Term Generation and Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    J.C. Ryman

    2003-07-31

    This calculation is a revision of a previous calculation (Ref. 7.5) that bears the same title and has the document identifier BBAC00000-01717-0210-00006 REV 01. The purpose of this revision is to remove TBV (to-be-verified) -41 10 associated with the output files of the previous version (Ref. 7.30). The purpose of this and the previous calculation is to generate source terms for a representative boiling water reactor (BWR) spent nuclear fuel (SNF) assembly for the first one million years after the SNF is discharged from the reactors. This calculation includes an examination of several ways to represent BWR assemblies and operating conditions in SAS2H in order to quantify the effects these representations may have on source terms. These source terms provide information characterizing the neutron and gamma spectra in particles per second, the decay heat in watts, and radionuclide inventories in curies. Source terms are generated for a range of burnups and enrichments (see Table 2) that are representative of the waste stream and stainless steel (SS) clad assemblies. During this revision, it was determined that the burnups used for the computer runs of the previous revision were actually about 1.7% less than the stated, or nominal, burnups. See Section 6.6 for a discussion of how to account for this effect before using any source terms from this calculation. The source term due to the activation of corrosion products deposited on the surfaces of the assembly from the coolant is also calculated. The results of this calculation support many areas of the Monitored Geologic Repository (MGR), which include thermal evaluation, radiation dose determination, radiological safety analyses, surface and subsurface facility designs, and total system performance assessment. This includes MGR items classified as Quality Level 1, for example, the Uncanistered Spent Nuclear Fuel Disposal Container (Ref. 7.27, page 7). Therefore, this calculation is subject to the requirements of the

  3. Assessment of the Prony's method for BWR stability analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz-Villafuerte, Javier, E-mail: javier.ortiz@inin.gob.m [Gerencia de Ciencias Aplicadas, Instituto Nacional de Investigaciones Nucleares, Carr. Mexico-Toluca S/N, La Marquesa, Ocoyoacac, Edo. Mexico 52750 (Mexico); Castillo-Duran, Rogelio, E-mail: rogelio.castillo@inin.gob.m [Gerencia de Ciencias Aplicadas, Instituto Nacional de Investigaciones Nucleares, Carr. Mexico-Toluca S/N, La Marquesa, Ocoyoacac, Edo. Mexico 52750 (Mexico); Palacios-Hernandez, Javier C., E-mail: javier.palacios@inin.gob.m [Gerencia de Ciencias Aplicadas, Instituto Nacional de Investigaciones Nucleares, Carr. Mexico-Toluca S/N, La Marquesa, Ocoyoacac, Edo. Mexico 52750 (Mexico)

    2011-05-15

    Highlights: This paper describes a method to determine the degree of stability of a BWR. Performance comparison between Prony's and common AR techniques is presented. Benchmark data and actual BWR transient data are used for comparison. DR and f results are presented and discussed. The Prony's method is shown to be a robust technique for BWR stability. - Abstract: It is known that Boiling Water Reactors are susceptible to present power oscillations in regions of high power and low coolant flow, in the power-flow operational map. It is possible to fall in one of such instability regions during reactor startup, since both power and coolant flow are being increased but not proportionally. One other possibility for falling into those areas is the occurrence of a trip of recirculation pumps. Stability monitoring in such cases can be difficult, because the amount or quality of power signal data required for calculation of the stability key parameters may not be enough to provide reliable results in an adequate time range. In this work, the Prony's Method is presented as one complementary alternative to determine the degree of stability of a BWR, through time series data. This analysis method can provide information about decay ratio and oscillation frequency from power signals obtained during transient events. However, so far not many applications in Boiling Water Reactors operation have been reported and supported to establish the scope of using such analysis for actual transient events. This work presents first a comparison of decay ratio and frequency oscillation results obtained by Prony's method and those results obtained by the participants of the Forsmark 1 and 2 Boiling Water Reactor Stability Benchmark using diverse techniques. Then, a comparison of decay ratio and frequency oscillation results is performed for four real BWR transient event data, using Prony's method and two other techniques based on an autoregressive modeling. The four

  4. Current and anticipated use of thermal-hydraulic codes for BWR transient and accident analyses in Japan

    Energy Technology Data Exchange (ETDEWEB)

    Arai, Kenji; Ebata, Shigeo [Toshiba Corp., Yokohama (Japan)

    1997-07-01

    This paper summarizes the current and anticipated use of the thermal-hydraulic and neutronic codes for the BWR transient and accident analyses in Japan. The codes may be categorized into the licensing codes and the best estimate codes for the BWR transient and accident analyses. Most of the licensing codes have been originally developed by General Electric. Some codes have been updated based on the technical knowledge obtained in the thermal hydraulic study in Japan, and according to the BWR design changes. The best estimates codes have been used to support the licensing calculations and to obtain the phenomenological understanding of the thermal hydraulic phenomena during a BWR transient or accident. The best estimate codes can be also applied to a design study for a next generation BWR to which the current licensing model may not be directly applied. In order to rationalize the margin included in the current BWR design and develop a next generation reactor with appropriate design margin, it will be required to improve the accuracy of the thermal-hydraulic and neutronic model. In addition, regarding the current best estimate codes, the improvement in the user interface and the numerics will be needed.

  5. Report on the BWR owners group radiation protection/ALARA Committee

    Energy Technology Data Exchange (ETDEWEB)

    Aldrich, L.R. [Commonwealth Edison Co., Downers Grove, IL (United States)

    1995-03-01

    Radiation protection programs at U.S. boiling water reactor (BWR) stations have evolved during the 1980s and early 1990s from a regulatory adherence-based endeavor to a proactive, risk-based radiation protection and prevention mission. The objectives are no longer to merely monitor and document exposure to radiation and radioactive materials. The focus of the current programs is the optimization of radiation protection of occupational workers consistent with the purpose of producing cost-effective electric power. The newly revised 10 CFR 20 defines the term ALARA (as low as reasonably achievable) to take into account the state of technology, the economics of improvements in relation to the state of the technology, and the benefits to the public health and safety. The BWR Owners Group (BWROG) initially formed the Radiation Protection/ALARA Committee in January 1990 to evaluate methods of reducing occupational radiation exposure during refueling outages. Currently, twenty U.S. BWR owner/operators (representing 36 of the operational 37 domestic BWR units), as well as three foreign BWR operators (associate members), have broadened the scope to promote information exchange between BWR radiation protection professionals and develop good practices which will affect optimization of their radiation protection programs. In search of excellence and the challenge of becoming {open_quotes}World Class{close_quotes} performers in radiation protection, the BWROG Radiation Protection/ALARA Committee has recently accepted a role in assisting the member utilities in improving radiation protection performance in a cost-effective manner. This paper will summarize the recent activities of this Committee undertaken to execute their role of exchanging information in pursuit of optimizing the improvement of their collective radiation protection performance.

  6. Flex concept for US-A BWR extended loss of AC power events

    Energy Technology Data Exchange (ETDEWEB)

    Powers, J. [Toshiba America Nuclear Energy, Charlotte, North Carolina (United States); Aoyagi, Y.; Kataoka, K. [Toshiba Corporation, Kawasaki, Kanagawa (Japan); Thomas, S.; Mookhoek, B., E-mail: jim.powers@toshiba.com [Nuclear Innovation North America, Lake Jackson, Texas (United States)

    2015-09-15

    The US-Advanced Boiling Water Reactor (US-A BWR), certified by the US NRC, is a third generation, evolutionary boiling water reactor design which is the reference for the South Texas Project Units 3 and 4 (Stp 3 and 4) Combined License Application (Cola) and incorporates numerous design and technology enhancements for improved safety performance. Nuclear Innovation North America (NINA) is the License Applicant for this new build project, and Toshiba is the selected primary technology contractor. The Stp 3 and 4 project has finished the US NRC technical review of the Cola, and the final safety evaluation report (FSER) is scheduled to be issued by the US NRC in 2015. Following the accident at the Fukushima Dai-ichi plant, the US-A BWR was reviewed for Beyond Design Basis Event (BDBE) safety using industry and regulatory guidance for US NRC Order EA-12-049 Order Modifying Licenses with Regard to Requirements for Mitigation of Beyond Design Basis External Events (BDBEE). By virtue of the design approach, the US-A BWR is capable of providing an indefinite coping period for a station blackout. The use of installed systems with extended coping times is a significant advantage of the US-A BWR compared to most of the plants currently operating in the U.S. In addition, the Stp 3 and 4 design incorporates enhancements consistent with the current US industry Diverse and Flexible Coping Strategies (Flex) initiative. The final technical topic requiring review by the US NRC Advisory Committee on Reactor Safeguards was the Flex Integrated Plan submitted by NINA, and this review was successfully completed. This paper summarizes the progress of the US-A BWR in licensing the Flex Integrated Plan for the project, and describes the technology and features of the US-A BWR design that contribute to safety post-Fukushima. It also provides an informational comparison of the design capabilities of the US-A BWR for extreme external events, and relates these capabilities to re

  7. Prony's method application for BWR instabilities characterization

    Energy Technology Data Exchange (ETDEWEB)

    Castillo, Rogelio, E-mail: rogelio.castillo@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Carretera México-Toluca s/n, La Marquesa, Ocoyoacac, Estado de México 52750 (Mexico); Ramírez, J. Ramón, E-mail: ramon.ramirez@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Carretera México-Toluca s/n, La Marquesa, Ocoyoacac, Estado de México 52750 (Mexico); Alonso, Gustavo, E-mail: gustavo.alonso@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Carretera México-Toluca s/n, La Marquesa, Ocoyoacac, Estado de México 52750 (Mexico); Instituto Politecnico Nacional, Unidad Profesional Adolfo Lopez Mateos, Ed. 9, Lindavista, D.F. 07300 (Mexico); Ortiz-Villafuerte, Javier, E-mail: javier.ortiz@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Carretera México-Toluca s/n, La Marquesa, Ocoyoacac, Estado de México 52750 (Mexico)

    2015-04-01

    Highlights: • Prony's method application for BWR instability events. • Several BWR instability benchmark are assessed using this method. • DR and frequency are obtained and a new parameter is proposed to eliminate false signals. • Adequate characterization of in-phase and out-of-phase events is obtained. • The Prony's method application is validated. - Abstract: Several methods have been developed for the analysis of reactor power signals during BWR power oscillations. Among them is the Prony's method, its application provides the DR and the frequency of oscillations. In this paper another characteristic of the method is proposed to determine the type of oscillations that can occur, in-phase or out-of-phase. Prony's method decomposes a given signal in all the frequencies that it contains, therefore the DR of the fundamental mode and the first harmonic are obtained. To determine the more dominant pole of the system a normalized amplitude W of the system is calculated, which depends on the amplitude and the damping coefficient. With this term, it can be analyzed which type of oscillations is present, if W of the fundamental mode frequency is the greater, the type of oscillations is in-phase, if W of the first harmonic frequency is the greater, the type of oscillations is out-of-phase. The method is applied to several stability benchmarks to assess its validity. Results show the applicability of the method as an alternative analysis method to determine the type of oscillations occurred.

  8. Passive BWR integral LOCA testing at the Karlstein test facility INKA

    Energy Technology Data Exchange (ETDEWEB)

    Drescher, Robert [AREVA GmbH, Erlangen (Germany); Wagner, Thomas [AREVA GmbH, Karlstein am Main (Germany); Leyer, Stephan [TH Univ. of Applied Sciences, Deggendorf (Germany)

    2014-07-01

    KERENA is an innovative AREVA GmbH boiling water reactor (BWR) with passive safety systems (Generation III+). In order to verify the functionality of the reactor design an experimental validation programme was executed. Therefore the INKA (Integral Teststand Karlstein) test facility was designed and erected. It is a mockup of the BWR containment with integrated pressure suppression system. In March 2013 the first integral test - Main Steam Line Break (MSLB) - was executed. The main target was to demonstrate the ability of the passive systems to ensure core coverage, decay heat removal and to maintain the containment within defined limits. The results of the test showed that the passive safety systems are capable to bring the plant to stable conditions meeting all required safety targets with sufficient margins. (orig.)

  9. BWR Anticipated Transients Without Scram Leading to Instability

    Energy Technology Data Exchange (ETDEWEB)

    Cheng L. Y.; Baek J.; Cuadra, A.; Aronson, A.; Diamond, D.; Yarsky, P.

    2013-11-10

    Anticipated transients without scram (ATWS) in aboiling water reactor (BWR) were simulated in order to understand reactor response and determine the effectiveness of automatic and operator actions to mitigate this beyond-design-basis accident. The events of interest herein are initiated by a turbine trip when the reactor is operating in the expanded operating domainMELLLA+ [maximum extended load line limit plus]. In these events the reactor may initially be at up to 120% of the original licensed thermal power (OLTP) and at flow rates as low as 80% of rated.For these (and similar) ATWS events the concern isthat when the reactor power decreases in response to a dual recirculation pump trip, the core will become unstable and large amplitude oscillations will begin. The occurrence of these power oscillations, if left unmitigated, may result in fuel damage, and the amplitude of the poweroscillations may hamper the effectiveness of the injection of dissolved neutron absorber through the standby liquid control system (SLCS).

  10. Multi-physical developments for safety related investigations of low moderated boiling water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Schlenker, Markus Thomas

    2014-12-19

    The main objective of this dissertation is the development and optimization of a low moderated boiling water reactor (BWR) core with improved fuel utilization to be incorporated in a Gen II BWR nuclear power plant. The assessment of the new core design is done by comparing it with a full MOX BWR core design regarding neutron physical and thermal-hydraulic design and safety criteria (e.g. inherent reactivity coefficients) and different sustainability parameters (e.g. conversion ratio).

  11. Development and Testing of CTF to Support Modeling of BWR Operating Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Salko, Robert K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wysocki, Aaron [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Collins, Benjamin S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Godfrey, Andrew T. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gosdin, Chris [Pennsylvania State Univ., University Park, PA (United States); Avramova, Maria [North Carolina State Univ., Raleigh, NC (United States)

    2016-01-29

    This milestone supports developing and assessing COBRA-TF (CTF) for the modeling of boiling water reactors (BWRs). This is achieved in three stages. First, a new preprocessor utility that is capable of handling BWR-specic design elements (e.g., channel boxes and large water rods) is developed. A previous milestone (L3:PHI.CTF.P12.01) led to the development of this preprocessor capability for single assembly models. This current milestone expands this utility so that it is applicable to multi-assembly BWR models that can be modeled in either serial or parallel. The second stage involves making necessary modications to CTF so that it can execute these new models. Specically, this means implementing an outer-iteration loop, specic to BWR models, that equalizes the pressure loss over all assemblies in the core (which are not connected due to the channel boxes) by adjusting inlet mass ow rate. A third stage involves assessing the standard convergence metrics that are used by CTF to determine when a simulation is steady-state. The nal stage has resulted in the implementation of new metrics in the code that give a better indication of how steady the solution is at convergence. This report summarizes these eorts and provides a demonstration of CTF's BWR-modeling capabilities. CASL-U-2016-1030-000

  12. Identification and assessment of BWR in-vessel severe accident mitigation strategies

    Energy Technology Data Exchange (ETDEWEB)

    Hodge, S.A.; Cleveland, J.C.; Kress, T.S.; Petek, M. [Oak Ridge National Lab., TN (United States)

    1992-10-01

    This report provides the results of work carried out in support of the US Nuclear Regulatory Commission Accident Management Research Program to develop a technical basis for evaluating the effectiveness and feasibility of current and proposed strategies for boiling water reactor (BWR) severe accident management. First, the findings of an assessment of the current status of accident management strategies for the mitigation of in-vessel events for BWR severe accident sequences are described. This includes a review of the BWR Owners` Group Emergency Procedure Guidelines (EPGSs) to determine the extent to which they currently address the characteristic events of an unmitigated severe accident and to provide the basis for recommendations for enhancement of accident management procedures. Second, where considered necessary, new candidate accident management strategies are proposed for mitigation of the late-phase (after core damage has occurred) events. Finally, recommendations are made for consideration of additional strategies where warranted, and two of the four candidate strategies identified by this effort are assessed in detail: (1) preparation of a boron solution for reactor vessel refill should control blade damage occur during a period of temporary core dryout and (2) containment flooding to maintain the core debris within the reactor vessel if the injection systems cannot be restored.

  13. BWR Servicing and Refueling Improvement Program: Phase I summary report

    Energy Technology Data Exchange (ETDEWEB)

    Perry, D.R.

    1978-09-01

    Under the U.S. Department of Energy sponsorship, General Electric Co. (GE) undertook a study of boiling water reactor (BWR) refueling outages for the purpose of recommending the development and demonstration of critical path time savings improvements. The Tennessee Valley Authority (TVA) joined the study as a subcontractor, providing monitoring assistance and making the Browns Ferry Site available for improvement demonstrations. Agreement was also reached with Georgia Power Co., Power Authority of the State of New York, and Commonwealth Edison Co. for monitoring and data collection at Hatch 1, FitzPatrick, and Quad Cities 1 nuclear plants, respectively. The objective was to identify, develop, and demonstrate improved refueling, maintenance, and inspection procedures and equipment. The improvements recommended in this study are applicable to BWR nuclear plants currently in operation as well as those in the design and construction phases. The recommendations and outage information can be used as a basis to plan and conduct the first outages of new plants and to improve the planning and facilities of currently operating plants. Many of the recommendations can readily be incorporated in plants currently in the design and construction phases as well as in the design of future plants. Many of these recommended improvements can be implemented immediately by utilities without further technical development.

  14. Cross-section adjustment techniques for BWR adaptive simulation

    Science.gov (United States)

    Jessee, Matthew Anderson

    Computational capability has been developed to adjust multi-group neutron cross-sections to improve the fidelity of boiling water reactor (BWR) modeling and simulation. The method involves propagating multi-group neutron cross-section uncertainties through BWR computational models to evaluate uncertainties in key core attributes such as core k-effective, nodal power distributions, thermal margins, and in-core detector readings. Uncertainty-based inverse theory methods are then employed to adjust multi-group cross-sections to minimize the disagreement between BWR modeling predictions and measured plant data. For this work, measured plant data were virtually simulated in the form of perturbed 3-D nodal power distributions with discrepancies with predictions of the same order of magnitude as expected from plant data. Using the simulated plant data, multi-group cross-section adjustment reduces the error in core k-effective to less than 0.2% and the RMS error in nodal power to 4% (i.e. the noise level of the in-core instrumentation). To ensure that the adapted BWR model predictions are robust, Tikhonov regularization is utilized to control the magnitude of the cross-section adjustment. In contrast to few-group cross-section adjustment, which was the focus of previous research on BWR adaptive simulation, multigroup cross-section adjustment allows for future fuel cycle design optimization to include the determination of optimal fresh fuel assembly designs using the adjusted multi-group cross-sections. The major focus of this work is to efficiently propagate multi-group neutron cross-section uncertainty through BWR lattice physics calculations. Basic neutron cross-section uncertainties are provided in the form of multi-group cross-section covariance matrices. For energy groups in the resolved resonance energy range, the cross-section uncertainties are computed using an infinitely-dilute approximation of the neutron flux. In order to accurately account for spatial and

  15. Water chemistry control and decontamination experience with TEPCO BWR`s and the measures planned for the future

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, N.; Miyamaru, K. [Tokyo Electric Power Co. (Japan)

    1995-03-01

    The new TEPCO BWR`s are capable of having the occupational radiation exposure controlled successfully at a low level by selecting low cobalt steel, using corrosion-resistant steel, employing dual condensate polishing systems, and controlling Ni/Fe ratio during operation. The occupational radiation exposure of the old BWR`s, on the other hand, remains high though reduced substantially through the use of low cobalt replacement steel and the partial addition of a filter in the condensate polishing system. Currently under review is the overall decontamination procedure for the old BWR`s to find out to measures needed to reduce the amount of crud that is and has been carried over into the nuclear reactor. The current status of decontamination is reported below.

  16. Oxide evolution on Alloy X-750 in simulated BWR environment

    Science.gov (United States)

    Tuzi, Silvia; Göransson, Kenneth; Rahman, Seikh M. H.; Eriksson, Sten G.; Liu, Fang; Thuvander, Mattias; Stiller, Krystyna

    2016-12-01

    In order to simulate the environment experienced by spacer grids in a boiling water reactor (BWR), specimens of the Ni-based Alloy X-750 were exposed to a water jet in an autoclave at a temperature of 286 °C and a pressure of 80 bar. The oxide microstructure of specimens exposed for 2 h, 24 h, 168 h and 840 h has been investigated mainly using electron microscopy. The specimens suffer mass loss due to dissolution during exposure. At the same time a complex layered oxide develops. After the longest exposure the oxide consists of two outer spinel layers consisting of blocky crystals, one intermediate layer of nickel oxide interspersed with Ti-rich oxide needles, and an inner layer of oxidized base metal. The evolution of the oxide leading up to this structure is discussed and a model is presented.

  17. Analyses of Instability Events in the Peach Bottom-2 BWR Using Thermal-Hydraulic and 3D Neutron Kinetic Coupled Codes Technique

    Directory of Open Access Journals (Sweden)

    Antonella Lombardi Costa

    2008-01-01

    Full Text Available Boiling water reactor (BWR instabilities may occur when, starting from a stable operating condition, changes in system parameters bring the reactor towards an unstable region. In order to design more stable and safer core configurations, experimental and theoretical studies about BWR stability have been performed to characterise the phenomenon and to predict the conditions for its occurrence. In this work, contributions to the study of BWR instability phenomena are presented. The RELAP5/MOD3.3 thermal-hydraulic (TH system code and the PARCS-2.4 3D neutron kinetic (NK code were coupled to simulate BWR transients. Different algorithms were used to calculate the decay ratio (DR and the natural frequency (NF from the power oscillation predicted by the transient calculations as two typical parameters used to provide a quantitative description of instabilities. The validation of the code model set up for the Peach Bottom Unit 2 BWR plant is performed against low-flow stability tests (LFSTs. The four series of LFST have been performed during the first quarter of 1977 at the end of cycle 2 in Pennsylvania. The tests were intended to measure the reactor core stability margins at the limiting conditions used in design and safety analyses.

  18. PWR and BWR spent fuel assembly gamma spectra measurements

    Science.gov (United States)

    Vaccaro, S.; Tobin, S. J.; Favalli, A.; Grogan, B.; Jansson, P.; Liljenfeldt, H.; Mozin, V.; Hu, J.; Schwalbach, P.; Sjöland, A.; Trellue, H.; Vo, D.

    2016-10-01

    A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative-Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of 137Cs, 154Eu, and 134Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. To compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.

  19. PWR and BWR spent fuel assembly gamma spectra measurements

    Energy Technology Data Exchange (ETDEWEB)

    Vaccaro, S. [European Commission, DG Energy, Directorate EURATOM Safeguards Luxembourg (Luxembourg); Tobin, S.J.; Favalli, A. [Los Alamos National Laboratory, Los Alamos, NM (United States); Grogan, B. [Oak Ridge National Laboratory, Oak Ridge (United States); Jansson, P. [Uppsala University, Uppsala (Sweden); Liljenfeldt, H. [Oak Ridge National Laboratory, Oak Ridge (United States); Mozin, V. [Lawrence Livermore National Laboratory, Livermore, CA (United States); Hu, J. [Oak Ridge National Laboratory, Oak Ridge (United States); Schwalbach, P. [European Commission, DG Energy, Directorate EURATOM Safeguards Luxembourg (Luxembourg); Sjöland, A. [Swedish Nuclear Fuel and Waste Management Company (SKB) (Sweden); Trellue, H.; Vo, D. [Los Alamos National Laboratory, Los Alamos, NM (United States)

    2016-10-11

    A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative–Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of {sup 137}Cs, {sup 154}Eu, and {sup 134}Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. To compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.

  20. High fidelity analysis of BWR fuel assembly with COBRA-TF/PARCS and trace codes

    Energy Technology Data Exchange (ETDEWEB)

    Abarca, A.; Miro, R.; Barrachina, T.; Verdu, G., E-mail: aabarca@isirym.upv.es, E-mail: rmiro@iqn.upv.es, E-mail: tbarrachina@isirym.upv.es, E-mail: gverdu@iqn.upv.es [Universitat Politecnica de Valencia, (ISIRYM/UPV), (Spain). Institute for Industrial, Radiophysical and Environmental Safety; Concejal, A.; Melara, J.; Albendea, M., E-mail: acbe@iberdrola.es, E-mail: jls@iberdrola.es, E-mail: manuel.albendea@iberdrola.es [Iberdrola, Madrid (Spain); Soler, A., E-mail: asoler@iberdrola.es [SEA Propulsion SL, Madrid (Spain)

    2013-07-01

    The growing importance of detailed reactor core and fuel assembly description for light water reactors (LWRs) as well as the sub-channel safety analysis requires high fidelity models and coupled neutronic/thermalhydraulic codes. Hand in hand with advances in the computer technology, the nuclear safety analysis is beginning to use a more detailed thermal hydraulics and neutronics. Previously, a PWR core and a 16 by 16 fuel assembly models were developed to test and validate our COBRA-TF/PARCS v2.7 (CTF/PARCS) coupled code. In this work, a comparison of the modeling and simulation advantages and disadvantages of modern 10 by 10 BWR fuel assembly with CTF/PARCS and TRACE codes has been done. The objective of the comparison is making known the main advantages of using the sub-channel codes to perform high resolution nuclear safety analysis. The sub-channel codes, like CTF, permits obtain accurate predictions, in two flow regime, of the thermalhydraulic parameters important to safety with high local resolution. The modeled BWR fuel assembly has 91 fuel rods (81 full length and 10 partial length fuel rods) and a big square central water rod. This assembly has been modeled with high level of detail with CTF code and using the BWR modeling parameters provided by TRACE. The same neutronic PARCS's model has been used for the simulation with both codes. To compare the codes a coupled steady state has be performed. (author)

  1. Light Water Reactor Sustainability Program BWR High-Fluence Material Project: Assessment of the Role of High-Fluence on the Efficiency of HWC Mitigation on SCC Crack Growth Rates

    Energy Technology Data Exchange (ETDEWEB)

    Sebastien Teysseyre

    2014-04-01

    As nuclear power plants age, the increasing neutron fluence experienced by stainless steels components affects the materials resistance to stress corrosion cracking and fracture toughness. The purpose of this report is to identify any new issues that are expected to rise as boiling water reactor power plants reach the end of their initial life and to propose a path forward to study such issues. It has been identified that the efficiency of hydrogen water chemistry mitigation technology may decrease as fluence increases for high-stress intensity factors. This report summarizes the data available to support this hypothesis and describes a program plan to determine the efficiency of hydrogen water chemistry as a function of the stress intensity factor applied and fluence. This program plan includes acquisition of irradiated materials, generation of material via irradiation in a test reactor, and description of the test plan. This plan offers three approaches, each with an estimated timetable and budget.

  2. Coolant Density and Control Blade History Effects in Extended BWR Burnup Credit

    Energy Technology Data Exchange (ETDEWEB)

    Ade, Brian J [ORNL; Marshall, William BJ J [ORNL; Bowman, Stephen M [ORNL; Gauld, Ian C [ORNL; Ilas, Germina [ORNL; Martinez-Gonzalez, Jesus S [ORNL

    2015-01-01

    Oak Ridge National Laboratory and the US Nuclear Regulatory Commission have initiated a multiyear project to investigate the application of burnup credit (BUC) for boiling water reactor (BWR) fuel in storage and transportation casks. This project includes two phases. The first phase investigates the applicability of peak reactivity methods currently used for spent fuel pools to spent fuel storage and transportation casks and the validation of reactivity (keff) calculations and predicted spent fuel compositions. The second phase focuses on extending BUC beyond peak reactivity. This paper documents work performed to date investigating some aspects of extended BUC. (The technical basis for application of peak reactivity methods to BWR fuel in storage and transportation systems is presented in a companion paper.) Two reactor operating parameters are being evaluated to establish an adequate basis for extended BWR BUC: (1) the effect of axial void profile and (2) the effect of control blade utilization during operation. A detailed analysis of core simulator data for one cycle of a modern operating BWR plant was performed to determine the range of void profiles and the variability of the profile experienced during irradiation. Although a single cycle does not provide complete data, the data obtained are sufficient to determine the primary effects and to identify conservative modeling approaches. These data were used in a study of the effect of axial void profile. The first stage of the study was determination of the necessary moderator density temporal fidelity in depletion modeling. After the required temporal fidelity was established, multiple void profiles were used to examine the effect on cask reactivity. The results of these studies are being used to develop recommendations for conservatively modeling the void profile effects for BWR depletion calculations. The second operational parameter studied was control blade history. Control blades are inserted in

  3. Extended Burnup Credit for BWR Spent Nuclear Fuel in Storage and Transportation Systems

    Energy Technology Data Exchange (ETDEWEB)

    Ade, Brian J [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bowman, Stephen M [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gauld, Ian C [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ilas, Germina [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Martinez, J. S. [Univ. Politecnica de Madrid (Spain). Dept. of Nuclear Engineering

    2015-01-01

    [Full Text] Oak Ridge National Laboratory and the United States Nuclear Regulatory Commission have initiated a multiyear project to investigate the application of burnup credit (BUC) for boiling-water reactor (BWR) fuel in storage and transportation casks. This project includes two phases. The first phase investigates the applicability of peak reactivity methods currently used for spent fuel pools to spent fuel storage and transportation casks and the validation of reactivity (keff) calculations and depleted fuel compositions. The second phase focuses on extending BUC beyond peak reactivity. This paper documents work performed to date, investigating some aspects of extended BUC, and it also describes the plan to complete the evaluations. The technical basis for application of peak reactivity methods to BWR fuel in storage and transportation systems is presented in a companion paper. Two reactor operating parameters are being evaluated to establish an adequate basis for extended BWR BUC, including investigation of the axial void profile effect and the effect of control blade utilization during operation. A detailed analysis of core simulator data for one cycle of an operating BWR plant was performed to determine the range of void profiles and the variability of the profile experienced during irradiation. While a single cycle does not provide complete data, the data obtained are sufficient to use to determine the primary effects and identify conservative modeling approaches. Using data resulting from a single cycle, the axial void profile is studied by first determining the temporal fidelity necessary in depletion modeling, and then using multiple void profiles to examine the effect of the void profile on cask reactivity. The results of these studies are being used to develop recommendations for conservatively modeling the void profile effects for BWR depletion calculations. The second operational parameter studied is control blade exposure. Control blades

  4. Radiation field control at the latest BWR plants -- design principle, operational experience and future subjects

    Energy Technology Data Exchange (ETDEWEB)

    Uchida, Shunsuke [Energy Research Lab., Ibaraki (Japan); Ohsumi, Katsumi; Takashima, Yoshie [Hitachi Works, Ibaraki (Japan)

    1995-03-01

    Improvements of operational procedures to control water chemistry, e.g., nickel/iron control, as well as application of hardware improvements for reducing radioactive corrosion products resulted in an extremely low occupational exposure of less than 0.5 man.Sv/yr without any serious impact on the radwaste system, for BWR plants involved in the Japanese Improvement and Standardization Program. Recently, {sup 60}C radioactively in the reactor water has been increasing due to less crud fixation on the two smooth surfaces of new type high performance fuels and to the pH drop caused by chromium oxide anions released from stainless steel structures and pipings. This increase must be limited by changes in water chemistry, e.g., applications of modified nickel/iron ratio control and weak alkali control. Controlled water chemistry to optimize three points, the plant radiation level and integrities of fuel and structural materials, is the primary future subject for BWR water chemistry.

  5. Effect of Control Blade History, and Axial Coolant Density and Burnup Profiles on BWR Burnup Credit

    Energy Technology Data Exchange (ETDEWEB)

    Ade, Brian J [ORNL; Marshall, William BJ J [ORNL; Martinez-Gonzalez, Jesus S [ORNL

    2015-05-01

    Oak Ridge National Laboratory (ORNL) and the US Nuclear Regulatory Commission (NRC) have initiated a multiyear project to investigate the application of burnup credit (BUC) for boiling water reactor (BWR) fuel in storage and transportation systems (often referred to as casks) and spent fuel pools (SFPs). This work is divided into two main phases. The first phase investigated the applicability of peak reactivity methods currently used in SFPs to transportation and storage casks and the validation of reactivity calculations and spent fuel compositions within these methods. The second phase focuses on extending BUC beyond peak reactivity. This paper documents the analysis of the effects of control blade insertion history, and moderator density and burnup axial profiles for extended BWR BUC.

  6. Decontamination as a precursor to decommissioning. Status report Task 2: process evaluation. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    Divine, J.R.; Woodruff, E.M.; McPartland, S.A.; Zima, G.E.

    1983-05-01

    As part of the US Nuclear Regulatory Commission's program to reduce occupational exposure and waste volumes, the Pacific Northwest Laboratory is studying decontamination as a precursor to decommissioning. Eleven processes or solvents were examined for their behavior in decontaminating BWR carbon steel samples. The solvents included NS-1, a proprietary solvent of Dow Chemical Corporation, designed for BWR use, and AP-Citrox, a well-known, two-step process designed for PWR stainless steel; it was used to provide a reference for later comparison to other systems and processes. The decontamination factors observed in the tests performed in a small laboratory scale recirculating loop ranged from about 1 (no effect) to 222 (about 99.6% of the initial activity removed. Coordinated corrosion measurements were made using twelve chemical solvents and eight metal alloys found in a range of reactor types.

  7. GOTHIC MODEL OF BWR SECONDARY CONTAINMENT DRAWDOWN ANALYSES

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, P.N.

    2004-10-06

    This article introduces a GOTHIC version 7.1 model of the Secondary Containment Reactor Building Post LOCA drawdown analysis for a BWR. GOTHIC is an EPRI sponsored thermal hydraulic code. This analysis is required by the Utility to demonstrate an ability to restore and maintain the Secondary Containment Reactor Building negative pressure condition. The technical and regulatory issues associated with this modeling are presented. The analysis includes the affect of wind, elevation and thermal impacts on pressure conditions. The model includes a multiple volume representation which includes the spent fuel pool. In addition, heat sources and sinks are modeled as one dimensional heat conductors. The leakage into the building is modeled to include both laminar as well as turbulent behavior as established by actual plant test data. The GOTHIC code provides components to model heat exchangers used to provide fuel pool cooling as well as area cooling via air coolers. The results of the evaluation are used to demonstrate the time that the Reactor Building is at a pressure that exceeds external conditions. This time period is established with the GOTHIC model based on the worst case pressure conditions on the building. For this time period the Utility must assume the primary containment leakage goes directly to the environment. Once the building pressure is restored below outside conditions the release to the environment can be credited as a filtered release.

  8. Range of the radiation monitor for the rigid vent of primary containment during normal and emergency operation for a BWR-5 in Laguna Verde; Rango del monitor de radiacion para el venteo rigido de la contencion primaria durante operacion normal y emergencia para un reactor BWR-5 en Laguna Verde

    Energy Technology Data Exchange (ETDEWEB)

    Tijerina S, F.; Pozos S, A. M.; Cabrera U, S.; Mata A, J. A.; Sandoval V, S.; Ovando C, R.; Vargas A, A.; Gallardo R, I.; Cruz G, M.; Amador C, C., E-mail: francisco.tijerina@cfe.gob.mx [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Subgerencia de Ingenieria, Km 44.5 Carretera Cardel-Nautla, 91476 Laguna Verde, Alto Lucero, Veracruz (Mexico)

    2014-10-15

    The earthquake followed by a tsunami, happened in March, 2011 in the coasts of oriental Japan, caused damages in the nuclear power plants 1 at 4 of Fukushima Daiichi leading to damage of the fuel in three of the reactors and to the radiation liberation to the exterior. As consequence of those events, the regulations requires that the power plants with Primary Containment type Mark I and II evaluate to have a system of rigid vent with a monitoring equipment of radiation effluents. The present work covers the rigid vent of diameter 12 of the Primary Containment, type Mark-II, of nuclear power plant of Laguna Verde in conditions of severe accident and normal operation, low regime of Extended Power Up rate (EPU - 2317 MWt), using the codes MAAP3B, MICROSHILED 5.05 and the Bardach Black Boxes methodology. As a result the measurement range of the radiation monitor that is required for monitoring the gassy liberation to the atmosphere was determined. The conclusion is that the superior limit of the range of the radiation meter during a Severe Accident is of 8.55 E + 05 R/h (8.55 E + 08 m R/h) and the superior limit in normal operation of 1.412 E-11 at 2.540 E-7 R/h (1.412 E-14 at 2.540 E-10 m R/h). (Author)

  9. Maintenance of fission and fusion reactors. 10. workshop on fusion reactor engineering

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-02-01

    This report contains copies of OHP presented at the title meeting. The presented topics are as follows, maintenance of nuclear power plants and ITER, exchange of shroud in BWR type reactors, deterioration of fission and fusion reactor materials, standards of pressure vessels, malfunction diagnosis method with neural network. (J.P.N.)

  10. RELAP4/MOD5: a computer program for transient thermal-hydraulic analysis of nuclear reactors and related systems. User's manual. Volume II. Program implementation. [PWR and BWR

    Energy Technology Data Exchange (ETDEWEB)

    None

    1976-09-01

    This portion of the RELAP4/MOD5 User's Manual presents the details of setting up and entering the reactor model to be evaluated. The input card format and arrangement is presented in depth, including not only cards for data but also those for editing and restarting. Problem initalization including pressure distribution and energy balance is discussed. A section entitled ''User Guidelines'' is included to provide modeling recommendations, analysis and verification techniques, and computational difficulty resolution. The section is concluded with a discussion of the computer output form and format.

  11. Cultura de integridade em pesquisa: somos agentes promotores

    Directory of Open Access Journals (Sweden)

    Ana Paula Abdon

    2015-03-01

    Full Text Available A Revista Brasileira em Promoção da Saúde (Brazilian Journal in Health Promotion, movida pela necessidade de uma cultura que estimule a integridade em pesquisa, quer enfatizar sua preocupação, não apenas com o conteúdo de suas publicações, mas também com os aspectos éticos que envolvem a submissão e a publicação dos manuscritos. Com isso, pretende levantar a discussão sobre boas práticas em pesquisa científica, ressaltando a importância de que este reforço ocorra desde os primeiros estágios da carreira dos pesquisadores. As más condutas éticas ocorrem em virtude das exigências crescente de produção intelectual e consequentemente as pressões sobre os pesquisadores vinculados aos programas de pós-graduação que utilizam os indicadores, principalmente, internacionais(1. A proliferação destas condutas antiéticas também é influenciada pelo “sistema de recompensas” existente, no qual o pesquisador é avaliado pela sua produtividade. O primeiro evento mundial sobre a integridade em pesquisa ocorreu em 2007 na cidade de Lisboa(2 e buscou sensibilizar a comunidade científica e editores para a importância de promover a conduta responsável na pesquisa. Em 2010, houve a segunda conferência mundial em Singapura(3. Desta conferência emergiu a “Declaração de Singapura sobre integridade em pesquisa” trazendo como princípios de integridade: a honestidade, a responsabilidade, o respeito e imparcialidade profissionais e a boa gestão da pesquisa(3. Em 2013, a terceira edição ocorreu em Montreal e teve como grande linha temática as investigações que cruzam as fronteiras e as parcerias internacionais(4. A exemplo destes movimentos internacionais, o Brasil também se mobilizou. Entretanto, esta preocupação é recente e tomou corpo após séries de publicações a respeito desta temática elaborado pela Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP(5 e pela publicação do Relatório da Comiss

  12. A New Methodology for Early Anomaly Detection of BWR Instabilities

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, K. N.

    2005-11-27

    The objective of the performed research is to develop an early anomaly detection methodology so as to enhance safety, availability, and operational flexibility of Boiling Water Reactor (BWR) nuclear power plants. The technical approach relies on suppression of potential power oscillations in BWRs by detecting small anomalies at an early stage and taking appropriate prognostic actions based on an anticipated operation schedule. The research utilizes a model of coupled (two-phase) thermal-hydraulic and neutron flux dynamics, which is used as a generator of time series data for anomaly detection at an early stage. The model captures critical nonlinear features of coupled thermal-hydraulic and nuclear reactor dynamics and (slow time-scale) evolution of the anomalies as non-stationary parameters. The time series data derived from this nonlinear non-stationary model serves as the source of information for generating the symbolic dynamics for characterization of model parameter changes that quantitatively represent small anomalies. The major focus of the presented research activity was on developing and qualifying algorithms of pattern recognition for power instability based on anomaly detection from time series data, which later can be used to formulate real-time decision and control algorithms for suppression of power oscillations for a variety of anticipated operating conditions. The research being performed in the framework of this project is essential to make significant improvement in the capability of thermal instability analyses for enhancing safety, availability, and operational flexibility of currently operating and next generation BWRs.

  13. Status report: Intergranular stress corrosion cracking of BWR core shrouds and other internal components

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    On July 25, 1994, the US Nuclear Regulatory Commission (NRC) issued Generic Letter (GL) 94-03 to obtain information needed to assess compliance with regulatory requirements regarding the structural integrity of core shrouds in domestic boiling water reactors (BWRs). This report begins with a brief description of the safety significance of intergranular stress corrosion cracking (IGSCC) as it relates to the design and function of BWR core shrouds and other internal components. It then presents a brief history of shroud cracking events both in the US and abroad, followed by an indepth summary of the industry actions to address the issue of IGSCC in BWR core shrouds and other internal components. This report summarizes the staff`s basis for issuing GL 94-03, as well as the staff`s assessment of plant-specific responses to GL 94-03. The staff is continually evaluating the licensee inspection programs and the results from examinations of BWR core shrouds and other internal components. This report is representative of submittals to and evaluations by the staff as of September 30, 1995. An update of this report will be issued at a later date.

  14. Pre-study of dynamic loads on the internals caused by a large pipe break in a BWR; Foerstudie av stroemningsinducerade laster paa interndelar vid brott i huvudcirkulationskretsarna i BWR

    Energy Technology Data Exchange (ETDEWEB)

    Marcinkiewicz, Jerzy; Lindgren, Anders [Det Norske Veritas Nuclear Technology AB, Stockholm (Sweden)

    2002-12-01

    Det Norske Veritas Nuclear Technology has performed a literature study of dynamic load on a BWR (Boiling Water Reactor) internals caused by a large pipe break. The goal of the study was to improve the knowledge about the physics of phenomena occurring in the RPV (Reactor Pressure Vessel) after pipe break in the main circulation system and also to make a review of calculation methods, models and computer programs including their capabilities when calculating the dynamic loads. The report presents description of relevant parts of a BWR, initial and boundary conditions, and phenomena determining the loads - rapid depressurization and propagation of pressure wave (including none-equilibrium). Furthermore, the report generally describes possible methodologies for calculating the dynamic loads on internals after the pipe break and the experiences from calculations the dynamic loads with different methods (computer programs) including comparisons with experimental data. Fluid-Structure Interaction methodology and its importance for calculation of dynamic loads on reactor internals is discussed based on experimental data. A very intensive research program for studying and calculating the dynamic loads on internals after pipe breaks has been performed in USA and Germany during the seventies and the eighties. Several computer programs have been developed and a number of large-scale experiments have been performed to calibrate the calculation methods. In spite of the fact that all experiments were performed for PWR several experiences should be valid also for BWR. These experiences, connected mainly to capabilities of computer programs calculating dynamic loads, are discussed in the report.

  15. Estimation of dose rate around the spent control rods of a BWR; Estimacion de la rapidez de dosis alrededor de las barras de control gastadas de un BWR

    Energy Technology Data Exchange (ETDEWEB)

    Cancino P, G.

    2016-10-01

    The energy can come from fossil renewable sources (solar (natural gas, oil), wind, hydro, tidal, geothermal, biomass, bio energy and nuclear. Nuclear power can be obtained by fission reactions and fusion (still under investigation) atomic nuclei. Fission, is a partition of a very heavy nucleus (Uranium 235, for example) into two lighter nuclei. Much of the world's electric power is generated from the energy released by fission processes. In a nuclear power reactor, light water as the BWR, there are many important elements that allow safe driving operation, one of them are the elements or control systems, the burnable poison or neutron absorber inherently allow control power reactor. The control rods, which consist mostly of stainless steel and absorbing elements (such as boron carbide, hafnium, cadmium, among others) of thermal neutrons is able to initiate, regulate or stop the reactor power. These, due to the use of depleted burned or absorbing material and therefore reach their lifespan, which can be 15 years or have other values depending on the manufacturer. Control rods worn should be removed, stored or confined in expressly places. Precisely at this stage arises the importance of knowing their radiological condition to manipulate safely and without incident to the people health responsible for conducting these proceedings state arises. This thesis consists in the estimation of the dose rate in spent control rod made of boron carbide, from a typical BWR reactor. It will be estimated by direct radiation measurements with measurement equipment for radiotherapy ionization chamber, in six spent control rods, which were taken at different reactor operating cycles and are in a spent fuel pool. Using bracket electromechanical and electronic equipment for positioning and lifting equipment for radiation measurement around the control rod in the axial and radial arrangement for proper scanning. Finally will be presented a graphic corresponding to the dose

  16. Benchmark calculation for radioactivity inventory using MAXS library based on JENDL-4.0 and JEFF-3.0/A for decommissioning BWR plants

    Directory of Open Access Journals (Sweden)

    Tanaka Ken-ichi

    2016-01-01

    Full Text Available We performed benchmark calculation for radioactivity activated in a Primary Containment Vessel (PCV of a Boiling Water Reactor (BWR by using MAXS library, which was developed by collapsing with neutron energy spectra in the PCV of the BWR. Radioactivities due to neutron irradiation were measured by using activation foil detector of Gold (Au and Nickel (Ni at thirty locations in the PCV. We performed activation calculations of the foils with SCALE5.1/ORIGEN-S code with irradiation conditions of each foil location as the benchmark calculation. We compared calculations and measurements to estimate an effectiveness of MAXS library.

  17. Design study of Thorium-232 and Protactinium-231 based fuel for long life BWR

    Science.gov (United States)

    Trianti, N.; Su'ud, Z.; Riyana, E. S.

    2012-06-01

    A preliminary design study for the utilization of thorium added with 231Pa based fuel on BWR type reactor has been performed. In the previous research utilization of fuel based Thorium-232 and Uranium-233 show 10 years operation time with maximum excess-reactivity about 4.075% dk/k. To increase reactor operation time and reduce excess-reactivity below 1% dk/k, Protactinium (Pa-231) is used as Burnable Poison. Protactinium-231 has very interesting neutronic properties, which enable the core to reduce initial excess-reactivity and simultaneously increase production of 233U to 231Pa in burn-up process. Optimizations of the content of 231Pa in the core enables the BWR core to sustain long period of operation time with reasonable burn-up reactivity swing. Based on the optimization of fuel element composition (Th and Pa) in various moderation ratio we can get reactor core with longer operation time, 20 ˜ 30 years operation without fuel shuffling or refuelling, with average power densities maximum of about 35 watt/cc, and maximum excess-reactivity 0.56% dk/k.

  18. BWR water chemistry guidelines and PWR primary water chemistry guidelines in Japan – Purpose and technical background

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, Hirotaka, E-mail: kawamuh@criepi.denken.or.jp [Central Research Institute of Electric Power Industry (Japan); Hirano, Hideo [Central Research Institute of Electric Power Industry (Japan); Katsumura, Yousuke [University of Tokyo (Japan); Uchida, Shunsuke [Tohoku University (Japan); Mizuno, Takayuki [Mie University (Japan); Kitajima, Hideaki; Tsuzuki, Yasuo [Japan Nuclear Safety Institute (Japan); Terachi, Takumi [Institute of Nuclear Safety System, Inc. (Japan); Nagase, Makoto; Usui, Naoshi [Hitachi-GE Nuclear Energy, Ltd. (Japan); Takagi, Junichi; Urata, Hidehiro [Toshiba Corporation (Japan); Shoda, Yasuhiko; Nishimura, Takao [Mitsubishi Heavy Industry, Ltd. (Japan)

    2016-12-01

    Highlights: • Framework of BWR/PWR water chemistry Guidelines in Japan are presented. • Guideline necessity, definitions, philosophy and technical background are mentioned. • Some guideline settings for control parameters and recommendations are explaines. • Chemistry strategy is also mentioned. - Abstract: After 40 years of light water reactor (LWR) operations in Japan, the sustainable development of water chemistry technologies has aimed to ensure the highest coolant system component integrity and fuel reliability performance for maintaining LWRs in the world; additionally, it aimed to achieve an excellent dose rate reduction. Although reasonable control and diagnostic parameters are utilized by each boiling water reactor (BWR) and pressurized water reactor (PWR) owner, it is recognized that specific values are not shared among everyone involved. To ensure the reliability of BWR and PWR operation and maintenance, relevant members of the Atomic Energy Society of Japan (AESJ) decided to establish guidelines for water chemistry. The Japanese BWR and PWR water chemistry guidelines provide strategies to improve material and fuel reliability performance as well as to reduce dosing rates. The guidelines also provide reasonable “control values”, “diagnostic values” and “action levels” for multiple parameters, and they stipulate responses when these levels are exceeded. Specifically, “conditioning parameters” are adopted in the Japanese PWR primary water chemistry guidelines. Good practices for operational conditions are also discussed with reference to long-term experience. This paper presents the purpose, technical background and framework of the preliminary water chemistry guidelines for Japanese BWRs and PWRs. It is expected that the guidelines will be helpful as an introduction to achieve safety and reliability during operations.

  19. Impact of modeling Choices on Inventory and In-Cask Criticality Calculations for Forsmark 3 BWR Spent Fuel

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Gonzalez, Jesus S. [Univ. Politecnica de Madrid (Spain); Ade, Brian J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bowman, Stephen M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gauld, Ian C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ilas, Germina [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Marshall, William BJ J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-01-01

    Simulation of boiling water reactor (BWR) fuel depletion poses a challenge for nuclide inventory validation and nuclear criticality safety analyses. This challenge is due to the complex operating conditions and assembly design heterogeneities that characterize these nuclear systems. Fuel depletion simulations and in-cask criticality calculations are affected by (1) completeness of design information, (2) variability of operating conditions needed for modeling purposes, and (3) possible modeling choices. These effects must be identified, quantified, and ranked according to their significance. This paper presents an investigation of BWR fuel depletion using a complete set of actual design specifications and detailed operational data available for five operating cycles of the Swedish BWR Forsmark 3 reactor. The data includes detailed axial profiles of power, burnup, and void fraction in a very fine temporal mesh for a GE14 (10×10) fuel assembly. The specifications of this case can be used to assess the impacts of different modeling choices on inventory prediction and in-cask criticality, specifically regarding the key parameters that drive inventory and reactivity throughout fuel burnup. This study focused on the effects of the fidelity with which power history and void fraction distributions are modeled. The corresponding sensitivity of the reactivity in storage configurations is assessed, and the impacts of modeling choices on decay heat and inventory are addressed.

  20. Irradiation-Assisted Stress Corrosion Cracking of Austenitic Stainless Steels in BWR Environments

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Y. [Argonne National Lab. (ANL), Argonne, IL (United States); Chopra, O. K. [Argonne National Lab. (ANL), Argonne, IL (United States); Gruber, Eugene E. [Argonne National Lab. (ANL), Argonne, IL (United States); Shack, William J. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2010-06-01

    The internal components of light water reactors are exposed to high-energy neutron irradiation and high-temperature reactor coolant. The exposure to neutron irradiation increases the susceptibility of austenitic stainless steels (SSs) to stress corrosion cracking (SCC) because of the elevated corrosion potential of the reactor coolant and the introduction of new embrittlement mechanisms through radiation damage. Various nonsensitized SSs and nickel alloys have been found to be prone to intergranular cracking after extended neutron exposure. Such cracks have been seen in a number of internal components in boiling water reactors (BWRs). The elevated susceptibility to SCC in irradiated materials, commonly referred to as irradiation-assisted stress corrosion cracking (IASCC), is a complex phenomenon that involves simultaneous actions of irradiation, stress, and corrosion. In recent years, as nuclear power plants have aged and irradiation dose increased, IASCC has become an increasingly important issue. Post-irradiation crack growth rate and fracture toughness tests have been performed to provide data and technical support for the NRC to address various issues related to aging degradation of reactor-core internal structures and components. This report summarizes the results of the last group of tests on compact tension specimens from the Halden-II irradiation. The IASCC susceptibility of austenitic SSs and heat-affected-zone (HAZ) materials sectioned from submerged arc and shielded metal arc welds was evaluated by conducting crack growth rate and fracture toughness tests in a simulated BWR environment. The fracture and cracking behavior of HAZ materials, thermally sensitized SSs and grain-boundary engineered SSs was investigated at several doses (≤3 dpa). These latest results were combined with previous results from Halden-I and II irradiations to analyze the effects of neutron dose, water chemistry, alloy compositions, and welding and processing conditions on IASCC

  1. BWR/5 Pressure-Suppression Pool Response during an SBO

    Directory of Open Access Journals (Sweden)

    Javier Ortiz-Villafuerte

    2013-01-01

    Full Text Available RELAP/SCDAPSIM Mod 3.4 has been used to simulate a station blackout occurring at a BWR/5 power station. Further, a simplified model of a wet well and dry well has been added to the NSSS model to study the response of the primary containment during the evolution of this accident. The initial event leading to severe accident was considered to be a LOOP with simultaneous scram. The results show that RCIC alone can keep the core fully covered, but even in this case about 30% of the original liquid water inventory in the PSP is vaporized. During the SBO, without RCIC, this inventory is reduced about 5% more within six hours. Further, a significant pressure rise occurs in containment at about the time when a sharp increase of heat generation occurs in RPV due to cladding oxidation. Failure temperature of fuel clad is also reached at this point. As the accident progresses, conditions for containment venting can be reached in about nine hours, although there still exists considerable margin before reaching containment design pressure. Detailed information of accident progress in reactor vessel and containment is presented and discussed.

  2. Obtaining meteorological data from historical newspapers: La Integridad

    Science.gov (United States)

    Ramírez-González, Ignacio A.; Añel, Juan A.; Saenz, Guadalupe; Gimeno, Luis; de la Torre, Laura; Polychroniadou, Eleni; Vidal-Mina, Renán

    2017-04-01

    The meteorological data recovery from old documentary sources is of huge significance for meteorological and weather research of our planet. In this work we present the meteorological series from the end of XIX century and the beginning of the XX at the A Guarda's Observatory, pioneer in Galicia in this kind of measurements and located in that time at "Colexio Xesuita Apóstol Santiago". The data series was obtained from meteorological notes of the catholic newspaper "La Integridad" published in that dates in Tui(Galicia). It was revised in total for this study more than 1000 newspapers from this publication and it was manually retrieved about 60000 individual measurements. Recovered variables include temperature, pressure, wind, relative humidity, vapor pressure, evaporation, precipitation and overview weather observations. This enables us to get a general picture of weather for this period of time in the studied region, to validate and to complete others independent data sources and study climate change. Also we prove the reliability of meteorological forecasts published from time to time in the same journal using sea level pressure fields from historical datasets provided by the MetOffice.

  3. Fracture toughness of irradiated wrought and cast austenitic stainless steels in BWR environment

    Energy Technology Data Exchange (ETDEWEB)

    Chopra, O.K.; Gruber, E.E.; Shack, W.J. [Argonne National Lab., Nuclear Engineering Div., Argonne, Illinois (United States)

    2007-07-01

    Experimental data are presented on the fracture toughness of wrought and cast austenitic stainless steels (SSs) that were irradiated to a fluence of {approx} 1.5 x 10{sup 21} n/cm{sup 2} (E > 1 MeV){sup *} ({approx} 2.3 dpa) at 296-305{sup o}C. To evaluate the possible effects of test environment and crack morphology on the fracture toughness of these steels, all tests were conducted in normal-water-chemistry boiling water reactor (BWR) environments at {approx} 289{sup o}C. Companion tests were also conducted in air on the same material for comparison. The fracture toughness J-R curves for SS weld heat-affected-zone materials in BWR water were found to be comparable to those in air. However, the results of tests on sensitized Type 304 SS and thermally aged cast CF-8M steel suggested a possible effect of water environment. The available fracture toughness data on irradiated austenitic SSs were reviewed to assess the potential for radiation embrittlement of reactor-core internal components. The synergistic effects of thermal and radiation embrittlement of cast austenitic SS internal components are also discussed. (author)

  4. Residual stress analysis in BWR pressure vessel attachments

    Energy Technology Data Exchange (ETDEWEB)

    Dexter, R.J.; Leung, C.P. (Southwest Research Inst., San Antonio, TX (United States)); Pont, D. (FRAMASOFT+CSI, 69 - Lyon (France). Div. of Framatome)

    1992-06-01

    Residual stresses from welding processes can be the primary driving force for stress corrosion cracking (SCC) in BWR components. Thus, a better understanding of the causes and nature of these residual stresses can help assess and remedy SCC. Numerical welding simulation software, such as SYSWELD, and material property data have been used to quantify residual stresses for application to SCC assessments in BWR components. Furthermore, parametric studies using SYSWELD have revealed which variables significantly affect predicted residual stress. Overall, numerical modeling techniques can be used to evaluate residual stress for SCC assessments of BWR components and to identify and plan future SCC research.

  5. Plagio e integridad académica en Alemania

    Directory of Open Access Journals (Sweden)

    2016-07-01

    Full Text Available Alemania es quizá uno de los países europeos que, ya desde el siglo XVIII, ha mantenido un debate público más intenso sobre prácticas científicas y académicas deshonestas, relacionadas especialmente con tesis doctorales. Este debate fue especialmente productivo a finales del siglo XIX, dando lugar desde entonces, para evitar estas prácticas inaceptables, a la obligatoriedad de publicar todas las tesis doctorales, como requisito previo a la expedición del título de doctor por cualquier universidad alemana. Este trabajo analiza los avances más importantes en plagio e integridad académica en Alemania, especialmente después del escándalo surgido en 2011 a raíz del plagio de la tesis doctoral del Ministro de Defensa Guttenberg, como son la creación de una eficaz metodología colaborativa de investigación del plagio en trabajos científicos o académicos utilizando Internet y las redes sociales, materializada en la Wiki «VroniPlag». También se describe someramente en este trabajo la consolidación definitiva de la figura del «Defensor de la Ciencia», como instrumento de ámbito nacional para prevenir, gestionar y combatir la deshonestidad científica, aparte de la publicación en 2013 de una nueva versión del manual de referencia al respecto «Sicherung guter wissenschaftlicher Praxis». Por último se analizan las conclusiones de la experiencia alemana relacionada con la ética académica, también desde una perspectiva histórica, pues sus recientes logros y avances pueden servir de referencia a otros países europeos.

  6. Obtention control bars patterns for a BWR using Tabo search; Obtencion de patrones de barras de control para un BWR usando busqueda Tabu

    Energy Technology Data Exchange (ETDEWEB)

    Castillo, A.; Ortiz, J.J.; Alonso, G. [Instituto Nacional de Investigaciones Nucleares, Km. 36.5 Carretera Mexico-Toluca, Ocoyoacac, Estado de Mexico 52045 (Mexico); Morales, L.B. [UNAM, IIMAS, Ciudad Universitaria, D. F. 04510 (Mexico); Valle, E. del [IPN, ESFM, Unidad Profesional ' Adolfo Lopez Mateos' , Col. Lindavista 07738, D. F. (Mexico)]. e-mail: jacm@nuclear.inin.mx

    2004-07-01

    The obtained results when implementing the technique of tabu search, for to optimize patterns of control bars in a BWR type reactor, using the CM-PRESTO code are presented. The patterns of control bars were obtained for the designs of fuel reloads obtained in a previous work, using the same technique. The obtained results correspond to a cycle of 18 months using 112 fresh fuels enriched at the 3.53 of U-235. The used technique of tabu search, prohibits recently visited movements, in the position that correspond to the axial positions of the control bars, additionally the tiempo{sub t}abu matrix is used for to manage a size of variable tabu list and the objective function is punished with the frequency of the forbidden movements. The obtained patterns of control bars improve the longitude of the cycle with regard to the reference values and they complete the restrictions of safety. (Author)

  7. Study of transient rod extraction failure without RBM in a BWR; Estudio del transitorio error de extraccion de barra sin RBM en un BWR

    Energy Technology Data Exchange (ETDEWEB)

    Vallejo Q, J. A.; Martin del Campo M, C.; Fuentes M, L.; Francois L, J. L., E-mail: amhed_jvq@hotmail.com [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Ciudad Universitaria, 04510 Ciudad de Mexico (Mexico)

    2015-09-15

    The study and analysis of the operational transients are important for predicting the behavior of a system to short-term events and the impact that would cause this transient. For the nuclear industry these studies are indispensable due to economic, environmental and social impacts that could cause an accident during the operation of a nuclear reactor. In this paper the preparation, simulation and analysis results of the transient rod extraction failure in which not taken into operation the RBM is presented. The study was conducted for a BWR of 2027 MWt, in an intermediate cycle of its useful life and using the computer code Simulate-3K a scenario of anomalies was created in the core reactivity which gave a coherent prediction to the type of presented event. (Author)

  8. Study of transient turbine shot without bypass in a BWR; Estudio del transitorio disparo de turbina sin bypass en un BWR

    Energy Technology Data Exchange (ETDEWEB)

    Vallejo Q, J. A.; Martin del Campo M, C.; Fuentes M, L.; Francois L, J. L., E-mail: amhed_jvq@hotmail.com [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Ciudad Universitaria, 04510 Ciudad de Mexico (Mexico)

    2015-09-15

    The study and analysis of operational transients are important for predicting the behavior of a system to short-terms events and the impact that would cause this transition. For the nuclear industry these studies are indispensable due to economic, environmental and social impacts that could result in an accident during the operation of a nuclear reactor. In this paper the preparation, simulation and analysis of results of a turbine shot transient, which is not taken into operation the bypass is presented. The study is realized for a BWR of 2027 MWt, to an intermediate cycle life and using the computer code Simulate-3K a depressurization stage of the vessel is created which shows the response of other security systems and gives a coherent prediction to the event presented type. (Author)

  9. Optimization of fuel reloads for a BWR using the ant colony system; Optimizacion de recargas de combustible para un BWR usando el sistema de colonia de hormigas

    Energy Technology Data Exchange (ETDEWEB)

    Esquivel E, J. [Universidad Autonoma del Estado de Mexico, Facultad de Ingenieria, Cerro de Coatepec s/n, Ciudad Universitaria, 50110 Toluca, Estado de Mexico (Mexico); Ortiz S, J. J. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)], e-mail: jaime.es.jaime@gmail.com

    2009-10-15

    In this work some results obtained during the development of optimization systems are presented, which are employees for the fuel reload design in a BWR. The systems use the ant colony optimization technique. As first instance, a system is developed that was adapted at travel salesman problem applied for the 32 state capitals of Mexican Republic. The purpose of this implementation is that a similarity exists with the design of fuel reload, since the two problems are of combinatorial optimization with decision variables that have similarity between both. The system was coupled to simulator SIMULATE-3, obtaining good results when being applied to an operation cycle in equilibrium for reactors of nuclear power plant of Laguna Verde. (Author)

  10. Crack growth rate in core shroud horizontal welds using two models for a BWR

    Energy Technology Data Exchange (ETDEWEB)

    Arganis Juárez, C.R., E-mail: carlos.arganis@inin.gob.mx; Hernández Callejas, R.; Medina Almazán, A.L.

    2015-05-15

    Highlights: • Two models were used to predict SCC growth rate in a core shroud of a BWR. • A weld residual stress distribution with 30% stress relaxation by neutron was used. • Agreement is shown between the measurements of SCC growth rate and the predictions. • Slip–oxidation model is better at low fluences and empirical model at high fluences. - Abstract: An empirical crack growth rate correlation model and a predictive model based on the slip–oxidation mechanism for Stress Corrosion Cracking (SCC) were used to calculate the crack growth rate in a BWR core shroud. In this study, the crack growth rate was calculated by accounting for the environmental factors related to aqueous environment, neutron irradiation to high fluence and the complex residual stress conditions resulting from welding. In estimating the SCC behavior the crack growth measurements data from a Boiling Water Reactor (BWR) plant are referred to, and the stress intensity factor vs crack depth throughout thickness is calculated using a generic weld residual stress distribution for a core shroud, with a 30% stress relaxation induced by neutron irradiation. Quantitative agreement is shown between the measurements of SCC growth rate and the predictions of the slip–oxidation mechanism model for relatively low fluences (5 × 10{sup 24} n/m{sup 2}), and the empirical model predicted better the SCC growth rate than the slip–oxidation model for high fluences (>1 × 10{sup 25} n/m{sup 2}). The relevance of the models predictions for SCC growth rate behavior depends on knowing the model parameters.

  11. Verification of the Advanced Nodal Method on BWR Core Analyses by Whole-Core Heterogeneous Transport Calculations

    Energy Technology Data Exchange (ETDEWEB)

    Shinya Kosaka

    2000-11-12

    Recent boiling water reactor (BWR) core and fuel designs have become more sophisticated and heterogeneous to improve fuel cycle cost, thermal margin, etc. These improvements, however, tend to lead to a strong interference effect among fuel assemblies, and it my cause some inaccuracies in the BWR core analyses by advanced nodal codes. Furthermore, the introduction of mixed-oxide (MOX) fuel will lead to a much stronger interference effect between MOX and UO{sub 2} fuel assemblies. However, the CHAPLET multiassembly characteristics transport code was developed recently to solve two-dimensional cell-heterogeneous whole-core problems efficiently, and its results can be used as reference whole-core solutions to verify the accuracy of nodal core calculations. In this paper, the results of nodal core calculations were compared with their reference whole-core transport solutions to verify their accuracy (in k{sub eff}, assembly power and pin power via pin power reconstruction) of the advanced nodal method on both UO{sub 2} and MOX BWR whole-core analyses. Especially, it was investigated if there were any significant differences in the accuracy between MOX and UO{sub 2} results.

  12. Development of a fuzzy logic method to build objective functions in optimization problems: application to BWR fuel lattice design

    Energy Technology Data Exchange (ETDEWEB)

    Martin-del-Campo, C.; Francois, J.L.; Barragan, A.M. [Universidad Nacional Autonoma de Mexico - Facultad de Ingenieria (Mexico); Palomera, M.A. [Universidad Nacional Autonoma de Mexico - Instituto de Investigaciones en Matematicas Aplicadas y Sistema, Mexico, D. F. (Mexico)

    2005-07-01

    In this paper we develop a methodology based on the use of the Fuzzy Logic technique to build multi-objective functions to be used in optimization processes applied to in-core nuclear fuel management. As an example, we selected the problem of determining optimal radial fuel enrichment and gadolinia distributions in a typical 'Boiling Water Reactor (BWR)' fuel lattice. The methodology is based on the use of the mathematical capability of Fuzzy Logic to model nonlinear functions of arbitrary complexity. The utility of Fuzzy Logic is to map an input space into an output space, and the primary mechanism for doing this is a list of if-then statements called rules. The rules refer to variables and adjectives that describe those variables and, the Fuzzy Logic technique interprets the values in the input vectors and, based on the set of rules assigns values to the output vector. The methodology was developed for the radial optimization of a BWR lattice where the optimization algorithm employed is Tabu Search. The global objective is to find the optimal distribution of enrichments and burnable poison concentrations in a 10*10 BWR lattice. In order to do that, a fuzzy control inference system was developed using the Fuzzy Logic Toolbox of Matlab and it has been linked to the Tabu Search optimization process. Results show that Tabu Search combined with Fuzzy Logic performs very well, obtaining lattices with optimal fuel utilization. (authors)

  13. Behaviour of the reactivity for BWR fuel cells; Comportamiento de la reactividad para celdas de combustible BWR

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, J. A.; Alonso, G.; Delfin, A.; Vargas, S. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Del Valle G, E., E-mail: galonso@inin.gob.mx [IPN, Escuela Superior de Fisica y Matematicas, U. P. Adolfo Lopez Mateos, Col. Lindavista, 07738 Mexico D. F. (Mexico)

    2011-11-15

    In this work the behaviour of the reactivity of a fuel assembly type BWR was studied, the objective is to obtain some expressions that consider the average enrichment of U-235 and the gadolinium concentration like a function of the fuel cells burnt. Also, the applicability of the lineal reactivity model was analyzed for fuel cells type BWR. The analysis was carried out with the CASMO-4 code. (Author)

  14. Transient and stability analysis of a BWR core with thorium-uranium fuel

    Energy Technology Data Exchange (ETDEWEB)

    Nunez-Carrera, Alejandro [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Barragan 779 Col. Narvarte, 03020 Mexico, DF (Mexico); Espinosa-Paredes, Gilberto [Division de Ciencias Basicas e Ingenieria, Universidad Autonoma Metropolitana, Av. San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico, DF (Mexico)], E-mail: gepe@xanum.uam.mx; Francois, Juan-Luis [Departamento de Sistemas Energeticos, Facultad de Ingenieria, Universidad Nacional Autonoma de Mexico, Paseo Cuauhnahuac 8532, 62550 Jiutepec Mor. (Mexico)

    2008-08-15

    The kinetic response of a boiling water reactor (BWR) equilibrium core using thorium as a nuclear material, in an integrated blanket-seed assembly, is presented in this work. Additionally an in-house code was developed to evaluate this core under steady state and transient conditions including a stability analysis. The code has two modules: (a) the time domain module for transient analysis and (b) the frequency domain module for stability analysis. The thermal-hydraulic process is modeled by a set of five equations, considering no homogeneous flow with drift-flux approximation and non-equilibrium thermodynamic. The neutronic process is calculated with a point kinetics model. Typical BWR reactivity effects are considered: void fraction, fuel temperature, moderator temperature and control rod density. Collapsed parameters were included in the code to represent the core using an average fuel channel. For the stability analysis, in the frequency domain, the transfer function is determined by applying Laplace-transforming to the calculated pressure drop perturbations in each of the considered regions where a constant total pressure drop was considered. The transfer function was used to study the system response in the frequency domain when an inlet flow perturbation is applied. The results show that the neutronic behavior of the core with thorium uranium fuel is similar to a UO{sub 2} core, even during transient conditions. The stability and transient analysis show that the thorium-uranium fuel can be operated safely in current BWRs.

  15. SUN-RAH: a nucleoelectric BWR university simulator based in reduced order models; SUN-RAH: simulador universitario de nucleoelectrica BWR basado en modelos de orden reducido

    Energy Technology Data Exchange (ETDEWEB)

    Morales S, J.B.; Lopez R, A.; Sanchez B, A.; Sanchez S, R.; Hernandez S, A. [DEPFI, Campus Morelos, en IMTA Jiutepec, Morelos (Mexico)]. e-mail: jms0620@yahoo.com

    2003-07-01

    The development of a simulator that allows to represent the dynamics of a nucleo electric central, with nuclear reactor of the BWR type, using reduced order models is presented. These models present the characteristics defined by the dominant poles of the system (1) and most of those premature operation transitories in a power station can be reproduced with considerable fidelity if the models are identified with data of plant or references of a code of better estimate like RAMONA, TRAC (2) or RELAP. The models of the simulator are developments or own simplifications starting from the physical laws and retaining the main terms. This work describes the objective of the project and the general specifications of the University student of Nucleo electric simulator with Boiling Water Reactor type (SUN-RAH) as well as the finished parts that fundamentally are the nuclear reactor, the one of steam supply (NSSS), the plant balance (BOP), the main controllers of the plant and the implemented graphic interfaces. The pendent goals as well as the future developments and applications of SUN-RAH are described. (Author)

  16. Technical Basis for Peak Reactivity Burnup Credit for BWR Spent Nuclear Fuel in Storage and Transportation Systems

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, William BJ J [ORNL; Ade, Brian J [ORNL; Bowman, Stephen M [ORNL; Gauld, Ian C [ORNL; Ilas, Germina [ORNL; Mertyurek, Ugur [ORNL; Radulescu, Georgeta [ORNL

    2015-01-01

    Oak Ridge National Laboratory and the United States Nuclear Regulatory Commission have initiated a multiyear project to investigate application of burnup credit for boiling-water reactor (BWR) fuel in storage and transportation casks. This project includes two phases. The first phase (1) investigates applicability of peak reactivity methods currently used in spent fuel pools (SFPs) to storage and transportation systems and (2) evaluates validation of both reactivity (keff) calculations and burnup credit nuclide concentrations within these methods. The second phase will focus on extending burnup credit beyond peak reactivity. This paper documents the first phase, including an analysis of lattice design parameters and depletion effects, as well as both validation components. Initial efforts related to extended burnup credit are discussed in a companion paper. Peak reactivity analyses have been used in criticality analyses for licensing of BWR fuel in SFPs over the last 20 years. These analyses typically combine credit for the gadolinium burnable absorber present in the fuel with a modest amount of burnup credit. Gadolinium burnable absorbers are used in BWR assemblies to control core reactivity. The burnable absorber significantly reduces assembly reactivity at beginning of life, potentially leading to significant increases in assembly reactivity for burnups less than 15–20 GWd/MTU. The reactivity of each fuel lattice is dependent on gadolinium loading. The number of gadolinium-bearing fuel pins lowers initial lattice reactivity, but it has a small impact on the burnup and reactivity of the peak. The gadolinium concentration in each pin has a small impact on initial lattice reactivity but a significant effect on the reactivity of the peak and the burnup at which the peak occurs. The importance of the lattice parameters and depletion conditions are primarily determined by their impact on the gadolinium depletion. Criticality code validation for BWR burnup

  17. BUTREN-RC an hybrid system for the recharges optimization of nuclear fuels in a BWR; BUTREN-RC un sistema hibrido para la optimizacion de recargas de combustible nuclear en un BWR

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz S, J.J.; Castillo M, J.A. [ININ, Carretera Mexico-Toluca Km. 36.5, 52045 Estado de Mexico (Mexico); Valle G, E. del [IPN, ESFM, 07738 Mexico D.F. (Mexico)

    2004-07-01

    The obtained results with the hybrid system BUTREN-RC are presented that obtains recharges of nuclear fuel for a BWR type reactor. The system has implemented the methods of optimization heuristic taboo search and neural networks. The optimization it carried out with the technique of taboo search, and the neural networks, previously trained, were used to predict the behavior of the recharges of fuel, in substitution of commercial codes of reactor simulation. The obtained recharges of nuclear fuel correspond to 5 different operation cycles of the Laguna Verde Nuclear Power plant, Veracruz in Mexico. The obtained results were compared with the designs of this cycles. The energy gain with the recharges of fuel proposals is of approximately 4.5% with respect to those of design. The time of compute consumed it was considerably smaller that when a commercial code for reactor simulation is used. (Author)

  18. Analysis of dose rates received around the storage pool for irradiated control rods in a BWR nuclear power plant.

    Science.gov (United States)

    Ródenas, J; Abarca, A; Gallardo, S

    2011-08-01

    BWR control rods are activated by neutron reactions in the reactor. The dose produced by this activity can affect workers in the area surrounding the storage pool, where activated rods are stored. Monte Carlo (MC) models for neutron activation and dose assessment around the storage pool have been developed and validated. In this work, the MC models are applied to verify the expected reduction of dose when the irradiated control rod is hanged in an inverted position into the pool. 2010 Elsevier Ltd. All rights reserved.

  19. Mobile crud and transportation of radioactivity in BWR

    Energy Technology Data Exchange (ETDEWEB)

    Hermansson, H-P. [Studsvik Nuclear AB, Nykoping (Sweden); LTU, Div. of Chemical Engineering, Lulea (Sweden); Hagg, J. [Ringhals AB, Varobacka (Sweden)

    2010-07-01

    Mobile crud is here referred to as a generic term for all types of particles that occur in the reactor water in BWRs and that are able to carry radioactivity. Previous results in this on-going series of studies in Swedish BWRs suggest that there are particles of different origins and function. A share may come from fuel crud and others may come from detachment, precipitation and dissolution processes in different parts of the BWR primary system, as well as from other system parts, such as the turbine/condenser. In addition, crud particles in this sense may come from purely mechanical processes such as degradation of graphite containing parts of the control rod drives. Therefore, the overall aim was to evaluate which particles are responsible for the transportation and distribution of radioactivity and also to clarify the chemical conditions under which they are formed. Furthermore the aim was to draw conclusions about how the chemistry would be like in order to avoid or at least minimize the formation of radioactivity distributing particles. A specific objective has also been to look into the importance of particle size for spreading of radioactivity in the primary system. Different types of crud particles are likely to have different characteristics in terms of function associated with transportation of radioactivity. The fuel crud is radioactive from the source and other types of crud can via surface processes, co-precipitation and other chemical and mechanical processes potentially affect the distribution of radioactivity in the primary system. In order to predict how operating parameters (e.g. stable, full power operation and scram) and chemical parameters (NWC/HWC/Zn, etc.) will affect the activity build-up on the system surfaces, it is important to know how the different types of crud are affected by these and related parameters. Fuel crud fixed on cladding ring samples, as well as mobile crud from the reactor water captured on filters, were examined by

  20. Enhancing BWR proliferation resistance fuel with minor actinides

    Science.gov (United States)

    Chang, Gray S.

    2009-03-01

    To reduce spent fuel for storage and enhance the proliferation resistance for the intermediate-term, there are two major approaches (a) increase the discharged spent fuel burnup in the advanced light water reactor- LWR (Gen-III Plus), which not only can reduce the spent fuel for storage, but also increase the 238Pu isotopes ratio to enhance the proliferation resistance, and (b) use of transuranic nuclides ( 237Np and 241Am) in the high burnup fuel, which can drastically increase the proliferation resistance isotope ratio of 238Pu/Pu. For future advanced nuclear systems, minor actinides (MA) are viewed more as a resource to be recycled, and transmuted to less hazardous and possibly more useful forms, rather than simply disposed of as a waste stream in an expensive repository facility. As a result, MAs play a much larger part in the design of advanced systems and fuel cycles, not only as additional sources of useful energy, but also as direct contributors to the reactivity control of the systems into which they are incorporated. In the study, a typical boiling water reactor (BWR) fuel unit lattice cell model with UO 2 fuel pins will be used to investigate the effectiveness of minor actinide reduction approach (MARA) for enhancing proliferation resistance and improving the fuel cycle performance in the intermediate-term goal for future nuclear energy systems. To account for the water coolant density variation from the bottom (0.76 g/cm 3) to the top (0.35 g/cm 3) of the core, the axial coolant channel and fuel pin were divided to 24 nodes. The MA transmutation characteristics at different elevations were compared and their impact on neutronics criticality discussed. The concept of MARA, which involves the use of transuranic nuclides ( 237Np and/or 241Am), significantly increases the 238Pu/Pu ratio for proliferation resistance, as well as serves as a burnable absorber to hold-down the initial excess reactivity. It is believed that MARA can play an important role in

  1. Development of a parametric containment event tree model for a severe BWR accident

    Energy Technology Data Exchange (ETDEWEB)

    Okkonen, T. [OTO-Consulting Ay, Helsinki (Finland)

    1995-04-01

    A containment event tree (CET) is built for analysis of severe accidents at the TVO boiling water reactor (BWR) units. Parametric models of severe accident progression and fission product behaviour are developed and integrated in order to construct a compact and self-contained Level 2 PSA model. The model can be easily updated to correspond to new research results. The analyses of the study are limited to severe accidents starting from full-power operation and leading to core melting, and are focused mainly on the use and effects of the dedicated severe accident management (SAM) systems. Severe accident progression from eight plant damage states (PDS), involving different pre-core-damage accident evolution, is examined, but the inclusion of their relative or absolute probabilities, by integration with Level 1, is deferred to integral safety assessments. (33 refs., 5 figs., 7 tabs.).

  2. Status update of the BWR cask simulator

    Energy Technology Data Exchange (ETDEWEB)

    Lindgren, Eric R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Durbin, Samuel G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    The performance of commercial nuclear spent fuel dry storage casks are typically evaluated through detailed numerical analysis of the system's thermal performance. These modeling efforts are performed by the vendor to demonstrate the performance and regulatory compliance and are independently verified by the Nuclear Regulatory Commission (NRC). Carefully measured data sets generated from testing of full sized casks or smaller cask analogs are widely recognized as vital for validating these models. Numerous studies have been previously conducted. Recent advances in dry storage cask designs have moved the storage location from above ground to below ground and significantly increased the maximum thermal load allowed in a cask in part by increasing the canister helium pressure. Previous cask performance validation testing did not capture these parameters. The purpose of the investigation described in this report is to produce a data set that can be used to test the validity of the assumptions associated with the calculations presently used to determine steady-state cladding temperatures in modern dry casks. These modern cask designs utilize elevated helium pressure in the sealed canister or are intended for subsurface storage. The BWR cask simulator (BCS) has been designed in detail for both the above ground and below ground venting configurations. The pressure vessel representing the canister has been designed, fabricated, and pressure tested for a maximum allowable pressure (MAWP) rating of 24 bar at 400 C. An existing electrically heated but otherwise prototypic BWR Incoloy-clad test assembly is being deployed inside of a representative storage basket and cylindrical pressure vessel that represents the canister. The symmetric single assembly geometry with well-controlled boundary conditions simplifies interpretation of results. Various configurations of outer concentric ducting will be used to mimic conditions for above and below ground storage configurations

  3. Analysis of the documents about the core envelopment of nuclear reactor at the Laguna Verde U-1 power plant; Analisis de documentos de los materiales de la envolvente del nucleo del reactor nuclear de la CLV U-1

    Energy Technology Data Exchange (ETDEWEB)

    Zamora R, L.; Medina F, A. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1999-07-01

    The degradation of internal components at BWR type reactors is an important subject to consider in the performance availability of the power plant. The Wuergassen nuclear reactor license was confiscated due to the presence of cracking in the core envelopment. In consequence it is necessary carrying out a detailed study with the purpose to avoid these problems in the future. This report presents a review and analysis of documents and technical information referring to the core envelopment of a BWR/5/6 and the Laguna Verde Unit 1 nuclear reactor in Mexico. In this document are presented design data, documents about fabrication processes, and manufacturing of core envelopment. (Author)

  4. An overview of the BWR ECCS strainer blockage issues

    Energy Technology Data Exchange (ETDEWEB)

    Serkiz, A.W.; Marshall, M.L. Jr.; Elliott, R. [Nuclear Regulatory Commission, Washington, DC (United States)

    1996-03-01

    This Paper provides a brief overview of actions taken in the mid 1980s to resolve Unresolved Safety Issue (USI) A-43, {open_quotes}Containment Emergency Sump Performance,{close_quotes} and their relationship to the BWR strainer blockage issue; the importance of insights gained from the Barseback-2 (a Swedish BWR) incident in 1992 and from ECCS strainer testing and inspections at the Perry nuclear power plant in 1992 and 1993; an analysis of an US BWR/4 with a Mark I containment; an international community sharing of knowledge relevant to ECCS strainer blockage, additional experimental programs; and identification of actions needed to resolve the strainer blockage issue and the status of such efforts.

  5. Experimental investigation of BWR Suppression Pool stratification during RCIC system operation

    Energy Technology Data Exchange (ETDEWEB)

    Solom, Matthew, E-mail: msolom@sandia.gov [Sandia National Laboratories, MS-0748, P.O. Box 5800, Albuquerque, NM 87185-0748 (United States); Vierow Kirkland, Karen [Department of Nuclear Engineering, Texas A& M University, MS 3133, College Station, TX 77843-3133 (United States)

    2016-12-15

    Highlights: • An experiment at Texas A&M University explored extended RCIC System operations. • Thermal stratification in Suppression Pools was found to develop and later disappear. • Greater containment pressure led to much greater vertical thermal stratification. - Abstract: In Boiling Water Reactor (BWR) nuclear power plants with the Mark I containment, the condition of the Suppression Pool can be a large influence on overall plant safety. When the Reactor Core Isolation Cooling (RCIC) System is operating, steam from the reactor drives the RCIC turbine and is then exhausted to the Suppression Pool. When subcooled, the pool can readily condense the steam, warming it up in the process. However, if hot spots or thermal stratification appear, this can limit the Suppression Pool’s ability to perform its safety functions, and can be a limiting factor for RCIC System operation. In order to better understand the RCIC system and its true limits of long-term operation, an experimental model of the system was constructed at the Laboratory for Nuclear Heat Transfer Systems at Texas A&M University (TAMU). These tests provide confirmation of thermal stratification in the Suppression Pool from RCIC System operations, and show a significant degree of dependence on pressure in the airspace above the pool. In the TAMU facility, vertical thermal stratification was limited to 21 °C when fully vented to atmospheric pressure, while pre-pressurization led to stratification well in excess of 60 °C.

  6. BWR stability using a reducing dynamical model; Estabilidad de un BWR con un modelo dinamico reducido

    Energy Technology Data Exchange (ETDEWEB)

    Ballestrin Bolea, J. M.; Blazquez Martinez, J. B.

    1990-07-01

    BWR stability can be treated with reduced order dynamical models. When the parameters of the model came from dynamical models. When the parameters of the model came from experimental data, the predictions are accurate. In this work an alternative derivation for the void fraction equation is made, but remarking the physical structure of the parameters. As the poles of power/reactivity transfer function are related with the parameters, the measurement of the poles by other techniques such as noise analysis will lead to the parameters, but the system of equations is non-linear. Simple parametric calculation of decay ratio are performed, showing why BWRs become unstable when they are operated at low flow and high power. (Author)

  7. ICTIOFAUNA COMO INDICADOR DA INTEGRIDADE BIÓTICA DE UM AMBIENTE DE ESTUÁRIO

    Directory of Open Access Journals (Sweden)

    Fabiane FISCH

    2016-01-01

    Full Text Available Numerosos métodos se utilizan para calcular los índices de integridad biótica (IIB en diferentes regiones del mundo. Este estudio tuvo como objetivo calcular el Índice de Integridad Biótica (IIB para un área de estuario en el sur de Brasil, a partir de datos de la comunidad de peces y así evaluar sus fluctuaciones en los últimos años. En este estudio se establecieron cuatro puntos de muestreo de las poblaciones de peces en el estuario del Saco da Fazenda en el Itajaí-SC, en muestras mensuales tomadas durante el período mayo/2012 a abril/2013. Las muestras fueron examinadas y los especímenes identificados hasta el nivel taxonómico de especies. El valor obtenido para el Índice de Integridad Biótica incluyó 11 atributos en cuatro grados de degradación de más de un año de muestreo. Se calcularon y se clasifican los valores del IIB en diferentes niveles para reconocer sus variaciones temporales y espaciales. IIB también se ha calculado utilizando los datos históricos (2000–2005, para mostrar los cambios en comparación con las investigaciones de campo recientes. El resultado para los años 2000-2002 indica una integridad biótica de calidad pobre, siendo de calidad regular para los años 2003-2005 y una regresión para pobre en los años 2012-2013.

  8. EFECTO DE LA CENTRIFUGACIÓN SOBRE LA INTEGRIDAD Y LA FUNCIONALIDAD DE ESPERMATOZOIDES EQUINOS

    Directory of Open Access Journals (Sweden)

    GIOVANNI RESTREPO-BETANCUR

    Full Text Available El objetivo de este estudio fue evaluar el efecto de la centrifugación sobre la integridad y la funcionalidad de espermatozoides equinos. Empleando el método de la vagina artificial se colectó el semen de diez reproductores equinos de la raza criollo colombiano, ubicados en El Valle de Aburrá (Antioquia, Colombia. Cada muestra de semen fue dividida en cuatro alícuotas, entre las cuales, tres fueron centrifugadas de forma separada a tres fuerzas de centrifugación (600 x g, 1200 x g y 1800 x g, durante 10 minutos a temperatura ambiente, mientras la cuarta no fue centrifugada (tratamiento control. Posteriormente, se evaluó la movilidad total y movilidad progresiva mediante un sistema analizador de clase (SCA®, al igual que se evaluaron el potencial de membrana mitocondrial, la vitalidad espermática y la integridad del acrosoma, mediante los ensayos fluorescentes JC1, SYBR/IP y FITC/PNA, respectivamente. Se concluye que incluso bajos niveles de fuerza de centrifugación, logran alterar la movilidad total, la movilidad progresiva, la integridad del acrosoma y el potencial de la membrana interna mitocondrial de los espermatozoides equinos.

  9. Technology, safety and costs of decommissioning a reference boiling water reactor power station. Volume 1. Main report. Technical report, September 1977-October 1979

    Energy Technology Data Exchange (ETDEWEB)

    Oak, H.D.; Holter, G.M.; Kennedy, W.E. Jr.; Konzek, G.J.

    1980-06-01

    Technology, safety and cost information is given for the conceptual decommissioning of a large (1100MWe) boiling water reactor (BWR) power station. Three approaches to decommissioning, immediate dismantlement, safe storage with deferred dismantlement and entombment, were studied to obtain comparisons between costs, occupational radiation doses, potential dose to the public and other safety impacts. It also shows the sensitivity of decommissioning safety and costs to the power rating of a BWR in the range of 200 to 1100 MWE.

  10. An efficient modeling method for thermal stratification simulation in a BWR suppression pool

    Energy Technology Data Exchange (ETDEWEB)

    Haihua Zhao; Ling Zou; Hongbin Zhang; Hua Li; Walter Villanueva; Pavel Kudinov

    2012-09-01

    The suppression pool in a BWR plant not only is the major heat sink within the containment system, but also provides major emergency cooling water for the reactor core. In several accident scenarios, such as LOCA and extended station blackout, thermal stratification tends to form in the pool after the initial rapid venting stage. Accurately predicting the pool stratification phenomenon is important because it affects the peak containment pressure; and the pool temperature distribution also affects the NPSHa (Available Net Positive Suction Head) and therefore the performance of the pump which draws cooling water back to the core. Current safety analysis codes use 0-D lumped parameter methods to calculate the energy and mass balance in the pool and therefore have large uncertainty in prediction of scenarios in which stratification and mixing are important. While 3-D CFD methods can be used to analyze realistic 3D configurations, these methods normally require very fine grid resolution to resolve thin substructures such as jets and wall boundaries, therefore long simulation time. For mixing in stably stratified large enclosures, the BMIX++ code has been developed to implement a highly efficient analysis method for stratification where the ambient fluid volume is represented by 1-D transient partial differential equations and substructures such as free or wall jets are modeled with 1-D integral models. This allows very large reductions in computational effort compared to 3-D CFD modeling. The POOLEX experiments at Finland, which was designed to study phenomena relevant to Nordic design BWR suppression pool including thermal stratification and mixing, are used for validation. GOTHIC lumped parameter models are used to obtain boundary conditions for BMIX++ code and CFD simulations. Comparison between the BMIX++, GOTHIC, and CFD calculations against the POOLEX experimental data is discussed in detail.

  11. CSAU methodology and results for an ATWS event in a BWR using information theory methods

    Energy Technology Data Exchange (ETDEWEB)

    Munoz-Cobo, J.L., E-mail: jlcobos@iqn.upv.es [Universitat Politècnica de València, Thermal-Hydraulics and Nuclear Engineering Group (TIN), Institute for Energy Engineering (IEE), Valencia (Spain); Escrivá, A., E-mail: aescriva@iqn.upv.es [Universitat Politècnica de València, Thermal-Hydraulics and Nuclear Engineering Group (TIN), Institute for Energy Engineering (IEE), Valencia (Spain); Mendizabal, R., E-mail: rmsanz@csn.es [Consejo de Seguridad Nuclear, 28040 Madrid (Spain); Pelayo, F., E-mail: fpl@csn.es [Consejo de Seguridad Nuclear, 28040 Madrid (Spain); Melara, J., E-mail: jls@iberdrola.es [IBERINCO, IBERDROLA Ingeniería y Construcción, Madrid (Spain)

    2014-10-15

    Highlights: • We apply the CSAU methodology to an ATWS in a BWR using information theory methods. • We show how to perform the selection of the most influential inputs on the critical safety parameter. • We apply the maximum entropy principle to get the input parameter distribution. • We examine the maximum relative entropy principle to update the input parameter PDF. • We quantify the uncertainty of the critical safety parameter using order statistics and information theory. - Abstract: This paper shows an application of the CSAU methodology to an ATWS in a BWR reactor, when the temperature of the suppression pool is taken as the critical safety parameter. The method combines CSAU methodology with recent techniques of information theory. In this paper we use auxiliary tools to help in the evaluation and improvement of the parameters distribution that enter in the elements II and III of CSAU based methodologies. These tools have been implemented in two FORTRAN programs: GEDIPA (Generation of the Parameter Distribution) and UNTHERCO (Uncertainty in Thermal Hydraulic Codes). The first one analyzes the information data available on a given parameter or parameters with the goal to know all the information about the probability distribution function of these parameters. The second apply information theory methods, as the maximum entropy principle (MEP) and the maximum relative entropy Principle (MREP), in order to build conservative distribution functions for the parameters from the available data. Also, the distribution function of a given parameter can be updated using the MREP principle when new information is provided. UNTHERCO performs the MONTECARLO sampling for a given set of parameters when the distribution function of these parameters is previously known. If the distribution of a parameter is unknown, then, the MEP is applied to deduce the distribution function for this parameter.

  12. Characteristics of debris in the lower head of a BWR in different severe accident scenarios

    Energy Technology Data Exchange (ETDEWEB)

    Phung, Viet-Anh, E-mail: vaphung@kth.se; Galushin, Sergey, E-mail: galushin@kth.se; Raub, Sebastian, E-mail: raub@kth.se; Goronovski, Andrei, E-mail: andreig@kth.se; Villanueva, Walter, E-mail: walterv@kth.se; Kööp, Kaspar, E-mail: kaspar@safety.sci.kth.se; Grishchenko, Dmitry, E-mail: dmitry@safety.sci.kth.se; Kudinov, Pavel, E-mail: pavel@safety.sci.kth.se

    2016-08-15

    Highlights: • Station blackout scenario with delayed recovery of safety systems in a Nordic BWR is considered. • Genetic algorithm and random sampling methods are used to explore accident scenario domain. • Main groups of scenarios are identified. • Ranges and distributions of characteristics of debris bed in the lower head are determined. - Abstract: Nordic boiling water reactors (BWRs) adopt ex-vessel debris cooling to terminate severe accident progression. Core melt released from the vessel into a deep pool of water is expected to fragment and form a coolable debris bed. Characteristics of corium melt ejection from the vessel determine conditions for molten fuel–coolant interactions (FCI) and debris bed formation. Non-coolable debris bed or steam explosion can threaten containment integrity. Vessel failure and melt ejection mode are determined by the in-vessel accident progression. Characteristics (such as mass, composition, thermal properties, timing of relocation, and decay heat) of the debris bed formed in the process of core relocation into the vessel lower plenum define conditions for the debris reheating, remelting, melt-vessel structure interactions, vessel failure and melt release. Thus core degradation and relocation are important sources of uncertainty for the success of the ex-vessel accident mitigation strategy. The goal of this work is improve understanding how accident scenario parameters, such as timing of failure and recovery of different safety systems can affect characteristics of the debris in the lower plenum. Station blackout scenario with delayed power recovery in a Nordic BWR is considered using MELCOR code. The recovery timing and capacity of safety systems were varied using genetic algorithm (GA) and random sampling methods to identify two main groups of scenarios: with relatively small (<20 tons) and large (>100 tons) amount of relocated debris. The domains are separated by the transition regions, in which relatively small

  13. Estimation of the coolant flow through a natural circulation BWR fuel channel applying and equivalent electrical model

    Energy Technology Data Exchange (ETDEWEB)

    Valle H, J.; Morales S, J. B. [UNAM, DEPFI, Laboratorio de Analisis de Ingenieria de Reactores Nucleares, Campus Morelos en IMTA, Jiutepec, Morelos (Mexico); Espinosa P, G., E-mail: julfi_ig@yahoo.com.m [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Av. San Rafael Atlixco No. 186, Col. Vicentina, 09340 Mexico D. F. (Mexico)

    2010-10-15

    This work presents the design and implementation of an advanced controller for a reduced order model of a BWR reactor core cooled by natural circulating water, which allows real time estimates of coolant flows through fuel assemblies about standard neutron flux strings. Nuclear power plants with boiling water reactors control individual fuel assembly coolant flows by forced circulation using external or internal water pumps and different core support plate orifices. These two elements reduce flow dependency on local channel pressure drops. In BWR reactors using only natural circulation coolant flows, these two elements are not available and therefore individual channel coolant flows are highly dependent in local conditions, such as power distributions and local pressure drops. Therefore it is expected that grater uncertainties in these variables be used during safety, fuel management and other analysis, which in turns may lead to increased operation penalties, such as tighter operating limits. The objective of this work is to asses by computer simulations means to reduce uncertainties in the measurement of fuel assembly coolant flows and eventually the associated penalties. During coolant phase transitions, pressure drops and local power may alter local natural circulation through fuel assemblies and flow estimates can be helped or not by control rod moves. This work presents the construction of an optimal controller for a core flow estimator based on a reduced order model of the coolant going though the reactor vessel components and nuclear core. This model is to be driven by plant signals from standard BWR instrumentation in order to estimate the coolant flows in selected fuel assemblies about a LPRM string. For this purpose an equivalent electrical model has been mathematically developed and numerically tested. The power-flow maps of typical BRW are used as steady state references for this equivalent model. Once these were fully reproduced for steady state

  14. Optimal estimate of the coolant flow in the assemblies of a BWR of natural circulation in real time; Estimacion optima del flujo de refrigerante en los ensambles de un BWR de circulacion natural en tiempo real

    Energy Technology Data Exchange (ETDEWEB)

    Valle H, J.; Morales S, J. B. [UNAM, Facultad de Ingenieria, Division de Estudios de Posgrado, Laboratorio de Analisis de Ingenieria de Reactores Nucleares, Paseo Cuauhnahuac 8532, Col. Progreso, 62550 Jiutepec, Morelos (Mexico); Espinosa P, G., E-mail: julfi_jg@yahoo.com.mx [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Av. San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico D. F. (Mexico)

    2012-10-15

    The present work exposes the design and the implementation of an advanced controller that allows estimating the coolant flow in the fuel assemblies of a BWR reactor of natural circulation in real time. To be able to reduce the penalizations that are established in the calculations of the operation limits due to the magnitude of the uncertainties in the coolant flows of a natural circulation reactor, is the objective of this research. In this work the construction of the optimal controller that allows estimating the coolant flows in a fuel channels group of the reactor is shown, as well as the operation of this applied to a reduced order model that simulates the dynamics of a natural circulation reactor. The controller design required of an estimator of the valuation variables not directly of the plant and of the estimates use of the local distributions of the coolant flow. The controller construction of the estimator was based mathematically in the filter Kalman whose algorithm allows to be carried out an advanced control of the system. To prove the estimator operation was development a simplified model that reproduces the basic dynamics of the flowing coolant in the reactor, which works as observer of the system, this model is coupled by means of the estimator controller to a detail model of the plant. The results are presented by means of graphics of the interest variables and the estimate flow, and they are documented in the chart that is presented at the end of this article. (Author)

  15. Technology, Safety and Costs of Decommissioning Nuclear Reactors At Multiple-Reactor Stations

    Energy Technology Data Exchange (ETDEWEB)

    Wittenbrock, N. G.

    1982-01-01

    Safety and cost information is developed for the conceptual decommissioning of large (1175-MWe) pressurized water reactors (PWRs) and large (1155-MWe) boiling water reactors {BWRs) at multiple-reactor stations. Three decommissioning alternatives are studied: DECON (immediate decontamination), SAFSTOR (safe storage followed by deferred decontamination), and ENTOMB (entombment). Safety and costs of decommissioning are estimated by determining the impact of probable features of multiple-reactor-station operation that are considered to be unavailable at a single-reactor station, and applying these estimated impacts to the decommissioning costs and radiation doses estimated in previous PWR and BWR decommissioning studies. The multiple-reactor-station features analyzed are: the use of interim onsite nuclear waste storage with later removal to an offsite nuclear waste disposal facility, the use of permanent onsite nuclear waste disposal, the dedication of the site to nuclear power generation, and the provision of centralized services. Five scenarios for decommissioning reactors at a multiple-reactor station are investigated. The number of reactors on a site is assumed to be either four or ten; nuclear waste disposal is varied between immediate offsite disposal, interim onsite storage, and immediate onsite disposal. It is assumed that the decommissioned reactors are not replaced in one scenario but are replaced in the other scenarios. Centralized service facilities are provided in two scenarios but are not provided in the other three. Decommissioning of a PWR or a BWR at a multiple-reactor station probably will be less costly and result in lower radiation doses than decommissioning an identical reactor at a single-reactor station. Regardless of whether the light water reactor being decommissioned is at a single- or multiple-reactor station: • the estimated occupational radiation dose for decommissioning an LWR is lowest for SAFSTOR and highest for DECON • the estimated

  16. The integrity of NSSS and containment during extended station blackout for Kuosheng BWR plant

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, Keng-Hsien; Yuann, Yng-Ruey; Lin, Ansheng [Atomic Energy Council, Taoyuan City, Taiwan (China). Inst. of Nuclear Energy Research

    2017-11-15

    The Fukushima Daiichi accident occurring on March 11, 2011, reveals that Station Blackout (SBO) may last longer than 8 h. However, the original design may not have sufficient capacity to cope with a SBO for more than 8 h. In view of this, Taiwan Power Company has initiated several enhancements to mitigate the severity of the extended SBO. Based on the improved plant configuration, a SBO coping analysis is performed in this study to assess whether the Kuosheng BWR plant has sufficient capability to cope with SBO for 24 h with respect to maintaining the integrity of the reactor core and containment. The analyses in the Nuclear Steam Supply System (NSSS) and the containment are based on the RETRAN-3D and GOTHIC models, respectively. The flow conditions calculated by RETRAN-3D during the event are retrieved and input to the GOTHIC containment model to determine the containment pressure and temperature response. These boundary conditions include SRV flow rate, SRV flow enthalpy, and total reactor coolant system leakage flow rate.

  17. HORIZONTAL LIFTING OF 5 DHLW/DOE LONG, 12-PWR LONG AND 24-BWR WASTE PACKAGES

    Energy Technology Data Exchange (ETDEWEB)

    V. de la Brosse

    2001-05-17

    The objective of this calculation was to determine the structural response of a 12-Pressurized Water Reactor (PWR) Long, a 24-Boiling Water Reactor (BWR) and a 5-Defense High Level Waste/Department of Energy (DHLW/DOE)--Long spent nuclear fuel waste packages lifted in a horizontal position. The scope of this calculation was limited to reporting the calculation results in terms of maximum stress intensities in the trunnion collar sleeves. In addition, the maximum stress intensities in the inner and outer shells of the waste packages were presented for illustrative purposes. The information provided by the sketches (Attachments I, II and III) is that of the potential design of the types of waste packages considered in this calculation, and all obtained results are valid for these designs only. This calculation is associated with the waste package design and was performed by the Waste Package Design Section in accordance with the ''Technical work plan for: Waste Package Design Description for LA'' (Ref. 7). AP-3.12Q, Calculations (Ref. 13), was used to perform the calculation and develop the document.

  18. Noise analysis of Forsmark 1 data to investigate BWR core local instability

    Energy Technology Data Exchange (ETDEWEB)

    Oguma, R. [GSE Power Systems AB, Nykoeping (Sweden)

    1998-04-01

    BWR core local instability was experienced at Forsmark 1 (F1) during reactor operation in cycle 16. The event has been studied by applying noise analysis and stability calculations to get insight into the event as well as to identify the cause of local instability. The present report is concerned with noise analysis of data collected during start-up in cycle 17. The results of the current study indicates: The F1 core is quite stable in cycle 17. The max. decay ratio (DR) value of 0.37 was obtained from the stability evaluation of an APRM (average power range monitor) and LPRM (local power range monitor) signals measured at 66% (APRM) of reactor power and 4252 Kg/s (SA-HC) of core flow. Compared with the power profile in cycle 17 (as well as in reactor F2), the core in cycle 16 had an extreme power profile with high power and bottom-shifted axial peak in the core periphery esp. at the four quadrant corners. Such a profile decreases the stability margin in the region. It is a common observation that the DR obtained from APRM tends to be higher than that from LPRM if the global instability mechanism is dominant in the core, and vice versa. The comparison of global and local DR values should be an effective method for detecting local instability during the reactor operation. In order to detect the local instability it is important to evaluate the core stability with sufficient number of LPRMs so as to cover the whole core cross section together with APRMs 8 refs, 16 figs

  19. Development and Assessment of CTF for Pin-resolved BWR Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Salko, Robert K [ORNL; Wysocki, Aaron J [ORNL; Collins, Benjamin S [ORNL; Avramova, Maria [North Carolina State University (NCSU), Raleigh; Gosdin, Chris [Pennsylvania State University

    2017-01-01

    CTF is the modernized and improved version of the subchannel code, COBRA-TF. It has been adopted by the Consortium for Advanced Simulation for Light Water Reactors (CASL) for subchannel analysis applications and thermal hydraulic feedback calculations in the Virtual Environment for Reactor Applications Core Simulator (VERA-CS). CTF is now jointly developed by Oak Ridge National Laboratory and North Carolina State University. Until now, CTF has been used for pressurized water reactor modeling and simulation in CASL, but in the future it will be extended to boiling water reactor designs. This required development activities to integrate the code into the VERA-CS workflow and to make it more ecient for full-core, pin resolved simulations. Additionally, there is a significant emphasis on producing high quality tools that follow a regimented software quality assurance plan in CASL. Part of this plan involves performing validation and verification assessments on the code that are easily repeatable and tied to specific code versions. This work has resulted in the CTF validation and verification matrix being expanded to include several two-phase flow experiments, including the General Electric 3 3 facility and the BWR Full-Size Fine Mesh Bundle Tests (BFBT). Comparisons with both experimental databases is reasonable, but the BFBT analysis reveals a tendency of CTF to overpredict void, especially in the slug flow regime. The execution of these tests is fully automated, analysis is documented in the CTF Validation and Verification manual, and the tests have become part of CASL continuous regression testing system. This paper will summarize these recent developments and some of the two-phase assessments that have been performed on CTF.

  20. Design and optimization of a fuel reload of BWR with plutonium and minor actinides; Diseno y optimizacion de una recarga de combustible de BWR con plutonio y actinidos menores

    Energy Technology Data Exchange (ETDEWEB)

    Guzman A, J. R.; Francois L, J. L.; Martin del Campo M, C.; Palomera P, M. A. [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Paseo Cuauhnahuac 8532, Jiutepec, Morelos 62550 (Mexico)]. e-mail: maestro_juan_rafael@hotmail.com

    2008-07-01

    In this work is designed and optimized a pattern of fuel reload of a boiling water reactor (BWR), whose fuel is compound of uranium coming from the enrichment lines, plutonium and minor actinides (neptunium, americium, curium); obtained of the spent fuel recycling of reactors type BWR. This work is divided in two stages: in the first stage a reload pattern designs with and equilibrium cycle is reached, where the reload lot is invariant cycle to cycle. This reload pattern is gotten adjusting the plutonium content of the assembly for to reach the length of the wished cycle. Furthermore, it is necessary to increase the concentration of boron-10 in the control rods and to introduce gadolinium in some fuel rods of the assembly, in order to satisfy the margin approach of out. Some reactor parameters are presented: the axial profile of power average of the reactor core, and the axial and radial distribution of the fraction of holes, for the one reload pattern in balance. For the design of reload pattern codes HELIOS and CM-PRESTO are used. In the second stage an optimization technique based on genetic algorithms is used, along with certain obtained heuristic rules of the engineer experience, with the intention of optimizing the reload pattern obtained in the first stage. The objective function looks for to maximize the length of the reactor cycle, at the same time as that they are satisfied their limits related to the power and the reactor reactivity. Certain heuristic rules are applied in order to satisfy the recommendations of the fuel management: the strategy of the control cells core, the strategy of reload pattern of low leakage, and the symmetry of a quarter of nucleus. For the evaluation of the parameters that take part in the objective function it simulates the reactor using code CM-PRESTO. Using the technique of optimization of the genetic algorithms an energy of the cycle of 10834.5 MW d/tHM is obtained, which represents 5.5% of extra energy with respect to the

  1. Optimization of fuel cells for BWR based in Tabu modified search; Optimizacion de celdas de combustible para BWR basada en busqueda Tabu modificada

    Energy Technology Data Exchange (ETDEWEB)

    Martin del Campo M, C.; Francois L, J.L. [Facultad de Ingenieria, UNAM, Laboratorio de Analisis en Ingenieria de Reactores Nucleares, Paseo Cuauhnahuac 8532, 62550 Jiutepec, Morelos (Mexico); Palomera P, M.A. [Facultad de Ingenieria, UNAM, Posgrado en Ingenieria en Computacion, Circuito exterior s/n, Ciudad Universitaria, Mexico, D.F. (Mexico)]. e-mail: cmcm@fi-b.unam.mx

    2004-07-01

    The advances in the development of a computational system for the design and optimization of cells for assemble of fuel of Boiling Water Reactors (BWR) are presented. The method of optimization is based on the technique of Tabu Search (Tabu Search, TS) implemented in progressive stages designed to accelerate the search and to reduce the time used in the process of optimization. It was programed an algorithm to create the first solution. Also for to diversify the generation of random numbers, required by the technical TS, it was used the Makoto Matsumoto function obtaining excellent results. The objective function has been coded in such a way that can adapt to optimize different parameters like they can be the enrichment average or the peak factor of radial power. The neutronic evaluation of the cells is carried out in a fine way by means of the HELIOS simulator. In the work the main characteristics of the system are described and an application example is presented to the design of a cell of 10x10 bars of fuel with 10 different enrichment compositions and gadolinium content. (Author)

  2. Technical Specification action statements requiring shutdown. A risk perspective with application to the RHR/SSW systems of a BWR

    Energy Technology Data Exchange (ETDEWEB)

    Mankamo, T. [Avaplan Oy, Espoo (Finland); Kim, I.S.; Samanta, P.K. [Brookhaven National Lab., Upton, NY (United States)

    1993-11-01

    When safety systems fail during power operation, the limiting conditions for operation (LCOs) and associated action statements of technical specifications typically require that the plant be shut down within the limits of allowed outage time (AOT). However, when a system needed to remove decay heat, such as the residual heat removal (RHR) system, is inoperable or degraded, shutting down the plant may not necessarily be preferable, from a risk perspective, to continuing power operation over a usual repair time, giving priority to the repairs. The risk impact of the basic operational alternatives, i.e., continued operation or shutdown, was evaluated for failures in the RHR and standby service water (SSW) systems of a boiling-water reactor (BWR) nuclear power plant. A complete or partial failure of the SSW system fails or degrades not only the RHR system but other front-line safety systems supported by the SSW system. This report presents the methodology to evaluate the risk impact of LCOs and associated AOT; the results of risk evaluation from its application to the RHR and SSW systems of a BWR; the findings from the risk-sensitivity analyses to identify alternative operational policies; and the major insights and recommendations to improve the technical specifications action statements.

  3. Condensate polishing guidelines for PWR and BWR plants

    Energy Technology Data Exchange (ETDEWEB)

    Robbins, P.; Crinigan, P.; Graham, B.; Kohlmann, R.; Crosby, C.; Seager, J.; Bosold, R.; Gillen, J.; Kristensen, J.; McKeen, A.; Jones, V.; Sawochka, S.; Siegwarth, D.; Keeling, D.; Polidoroff, T.; Morgan, D.; Rickertsen, D.; Dyson, A.; Mills, W.; Coleman, L.

    1993-03-01

    Under EPRI sponsorship, an industry committee, similar in form and operation to other guideline committees, was created to develop Condensate Polishing Guidelines for both PWR and BWR systems. The committee reviewed the available utility and water treatment industry experience on system design and performance and incorporated operational and state-of-the-art information into document. These guidelines help utilities to optimize present condensate polisher designs as well as be a resource for retrofits or new construction. These guidelines present information that has not previously been presented in any consensus industry document. The committee generated guidelines that cover both deep bed and powdered resin systems as an integral part of the chemistry of PWR and BWR plants. The guidelines are separated into sections that deal with the basis for condensate polishing, system design, resin design and application, data management and performance and management responsibilities.

  4. Undermoderated spectrum MOX core study. Advanced fuel recycle by BWR

    Energy Technology Data Exchange (ETDEWEB)

    Matuyama, Shinichiro; Sakashita, Yoshiaki [Toshiba Corp., Kawasaki, Kanagawa (Japan)

    1998-09-01

    The concept of BARS (BWR with Advanced Recycle System) is described. This system is to recycle fuel for breeding type BWR using spent fuel by the dry reprocessing. At present, it is studying about the high spectrum core cooling with light water, the dry reprocessing, Vibration Compaction fuel and so on. In the dry reprocessing method used oxide, RE and DF are one of the technical issues. In the case that DF is about 10, RE doesn`t influence a core behavior. According to improve the present process, the possibility lies in making DF from 5 to equal or more than 10 sufficiently. Here, the outline, the development situation of these studies and the prospect of BARS from ability are explained. (author)

  5. 3D simulation of a core operation cycle of a BWR using Serpent; Simulacion 3D de un ciclo de operacion del nucleo de un BWR usando SERPENT

    Energy Technology Data Exchange (ETDEWEB)

    Barrera Ch, M. A.; Del Valle G, E. [IPN, Escuela Superior de Fisica y Matematicas, Av. IPN s/n, Col. Lindavista, 07738 Ciudad de Mexico (Mexico); Gomez T, A. M., E-mail: rionchez@icloud.com [ININ, Departamento de Sistemas Nucleares, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2016-09-15

    This work had the main goal to develop a methodology to obtain the length of an operating cycle of the core of a BWR under different operating states using the Serpent code. The reactor core modeled in Serpent is composed of 444 fuel assemblies (120 with fresh fuels and 324 fuels from previous cycles), 109 cruciform control rods and light water as moderator and coolant. Once the core of the reactor was modeled in Serpent (Three-dimensional) without considering the cruciform control rods, a simulation was carried out with different steps of burning in the operational state with the average values of the fuel temperature (900 K), moderator temperature (600 K) and voids fraction equal to 0.4. In addition, the thermal power considered was 2017 MWt. This operational state was chosen because a previous analysis (not shown in this work) was carried out in 4 types of control cells. The first and second control cell has all of its natural uranium fuel pellets, with control rod and without control rod respectively. The third and fourth control cell types have various types of enrichment, both natural uranium and gadolinium in their fuel pellets, with control rod and without control rod. The conclusion of this previous analysis was that the behavior of the effective multiplication factor along the fuel burnout within the four control cell types was almost unaffected by the fuel temperature but was affected by the voids fraction. Thus, for this operating cycle in the operating state defined above, its length was 14,63052 GW t/Tm. In addition, at the end of this cycle, the decay heat obtained was equal to 116.71 MWt and the inventory of the most important isotopes to be considered was obtained, such as some isotopes of uranium, neptune, plutonium, americium and curio. (Author)

  6. RAMONA-4B a computer code with three-dimensional neutron kinetics for BWR and SBWR system transient - user`s manual

    Energy Technology Data Exchange (ETDEWEB)

    Rohatgi, U.S.; Cheng, H.S.; Khan, H.J.; Mallen, A.N.; Neymotin, L.Y.

    1998-03-01

    This document is the User`s Manual for the Boiling Water Reactor (BWR), and Simplified Boiling Water Reactor (SBWR) systems transient code RAMONA-4B. The code uses a three-dimensional neutron-kinetics model coupled with a multichannel, nonequilibrium, drift-flux, phase-flow model of the thermal hydraulics of the reactor vessel. The code is designed to analyze a wide spectrum of BWR core and system transients. Chapter 1 gives an overview of the code`s capabilities and limitations; Chapter 2 describes the code`s structure, lists major subroutines, and discusses the computer requirements. Chapter 3 is on code, auxillary codes, and instructions for running RAMONA-4B on Sun SPARC and IBM Workstations. Chapter 4 contains component descriptions and detailed card-by-card input instructions. Chapter 5 provides samples of the tabulated output for the steady-state and transient calculations and discusses the plotting procedures for the steady-state and transient calculations. Three appendices contain important user and programmer information: lists of plot variables (Appendix A) listings of input deck for sample problem (Appendix B), and a description of the plotting program PAD (Appendix C). 24 refs., 18 figs., 11 tabs.

  7. A methodology for obtaining the control rod patterns in a BWR using genetic algorithms; Una metodologia para obtener los patrones de barras de control en un BWR usando algoritmos geneticos

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz S, J.J.; Montes T, J.L. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Requena R, I. [Universidad de Granada, 18071 Granada (Spain)]. e-mail: jjortiz@nuclear.inin.mx

    2003-07-01

    In this work the GACRP system based on the genetic algorithms technique for the obtaining of the drivers of control bars in a BWR reactor is presented. This methodology was applied to a transition cycle and a one of balance of the Laguna Verde nuclear power station (CNLV). For each one of the studied cycles, it was executed the methodology with a fixed length of the cycle and it was compared the effective multiplication factor of neutrons at the end of the cycle that it is obtained with the proposed drivers of control bars and the multiplication factor of neutrons obtained by means of a Haling calculation. It was found that it is possible to extend several days the length of both cycles with regard to the one Haling calculation. (Author)

  8. Impact analysis of modifying the composition of the nuclear fuel of a BWR with beryllium oxide; Analisis del impacto de modificar la composicion del combustible nuclear de un BWR con oxido de berilio

    Energy Technology Data Exchange (ETDEWEB)

    Gallardo V, J. M.; Morales S, J. B., E-mail: euqrop@hotmail.com [UNAM, Facultad de Ingenieria, Ciudad Universitaria, 04510 Mexico D. F. (Mexico)

    2013-10-15

    The beryllium oxide (Be O) presents excellent physical properties, especially its high thermal conductivity that contrasts clearly with that of the uranium dioxide (UO{sub 2}) used at the present as fuel in a great number of nuclear plants. The present work models a nuclear reactor cooled by light water in boiling with two external recirculation loops (BWR/5) using the code for the transitory analysis and postulated accidents Trac-B F1, implementing a UO{sub 2} mixture and different fractions of Be O, with the objective of improving the thermal conductivity of the fuel. The numeric results and the realized analyses indicate that when adding a fraction in volume of 10% the central temperature decreases in 30.4% in stationary state, while during the large break loss of coolant accident the peak cladding temperature diminishes in 7%. Although the real interaction of the mixture has not been determined experimentally, the obtained results are promising. (Author)

  9. Trace Assessment for BWR ATWS Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, L.Y.; Diamond, D.; Arantxa Cuadra, Gilad Raitses, Arnold Aronson

    2010-04-22

    A TRACE/PARCS input model has been developed in order to be able to analyze anticipated transients without scram (ATWS) in a boiling water reactor. The model is based on one developed previously for the Browns Ferry reactor for doing loss-of-coolant accident analysis. This model was updated by adding the control systems needed for ATWS and a core model using PARCS. The control systems were based on models previously developed for the TRAC-B code. The PARCS model is based on information (e.g., exposure and moderator density (void) history distributions) obtained from General Electric Hitachi and cross sections for GE14 fuel obtained from an independent source. The model is able to calculate an ATWS, initiated by the closure of main steam isolation valves, with recirculation pump trip, water level control, injection of borated water from the standby liquid control system and actuation of the automatic depres-surization system. The model is not considered complete and recommendations are made on how it should be improved.

  10. Educación permanente y continua en una perspectiva de integridad del ser

    Directory of Open Access Journals (Sweden)

    Izabel Cristina Feijó de Andrade

    2014-12-01

    Full Text Available Este artículo buscó discutir las articulaciones y distinciones entre los conceptos de educación permanente y educación continua de modo que favorezca la perspectiva de integridad del ser, vínculo que requiere saberes hasta entonces poco privilegiados en las Universidades y que demandan el rescate de dimensiones basadas en la experiencia, la didáctica y la existencia del educador, tanto individual, comportamental, cultural, social y espiritual. Consideramos que las nociones de educación permanente y educación continua poseen elementos entrelazables que nos permiten desarrollar la capacidad de reaccionar críticamente por medio de una relación autoformativa. Las revisiones teóricas implementadas permitieron algunas consideraciones sobre los procesos formativos actuales y las prácticas de profesores rumbo a una Educación para la Integridad. Concluimos provisoriamente que las aproximaciones y distinciones entre EP y EC pueden proporcionar a los profesores la toma de conciencia de su vinculación todo/parte y del sentido de la vida.

  11. ICTIOFAUNA COMO INDICADOR DA INTEGRIDADE BIÓTICA DE UM AMBIENTE DE ESTUÁRIO

    Directory of Open Access Journals (Sweden)

    Fabiane Fisch

    2015-11-01

    Full Text Available RESUMOInúmeros métodos são utilizados para calcular índices de integridade biótica (IIB em diferentes regiões do mundo. Esse trabalho teve por objetivo calcular o Índice de Integridade Biótica (IIB, para uma área estuarina no Sul do Brasil, a partir de dados da comunidade de peixes e avaliar suas flutuações ao longo dos anos. Neste estudo foram estabelecidos quatro pontos para amostragem da ictiofauna, no estuário Saco da Fazenda em Itajaí-SC, em coletas mensais realizadas entre maio/2012 a abril/2013. As amostras foram triadas e os espécimes identificados até o nível taxonômico de espécie. O valor obtido para o Índice de Integridade Biótica incluiu 11 atributos, em quatro graus de degradação ao longo de um ano de amostragem. Os valores do IIB foram calculados e classificados em diferentes níveis para reconhecer suas variações temporais e espaciais. Foi calculado também o IIB utilizando os dados históricos (2000 a 2005, para mostrar as alterações em comparação com as investigações de campo recentes. O resultado para os anos de 2000-2002 indica uma integridade biótica pobre, sendo regular para os anos de 2003-2005 e regredindo para pobre nos anos de 2012-2013.ABSTRACTNumerous methods are used to calculate the Index of Biotic Integrity (IIB in diverse regions of the world. The objective of this work is to calculate the Index of Biotic Integrity (IIB, for an estuarine area in southern Brazil from fish community data and evaluate their fluctuations over the years. In this study, four ichthyofauna sampling points were established in the estuary “Saco da Fazenda”, Itajaí-SC, in monthly samples taken during the period of May/2012 and April/2013. The samples were screened and the specimens identified at the taxonomic level of species. The value obtained for the Index of Biotic Integrity included 11 attributes, in four degrees of degradation over a year of sampling. Values were calculated and IIB classified into

  12. Improving the neutronic characteristics of a boiling water reactor by using uranium zirconium hydride fuel instead of uranium dioxide fuel

    Energy Technology Data Exchange (ETDEWEB)

    Galahom, Ahmed Abdelghafar [Higher Technological Institute, Ramadan (Egypt)

    2016-06-15

    The present work discusses two different models of boiling water reactor (BWR) bundle to compare the neutronic characteristics of uranium dioxide (UO{sub 2}) and uranium zirconium hydride (UZrH{sub 1.6}) fuel. Each bundle consists of four assemblies. The BWR assembly fueled with UO{sub 2} contains 8 × 8 fuel rods while that fueled with UZrH{sub 1.6} contains 9 × 9 fuel rods. The Monte Carlo N-Particle Transport code, based on the Mont Carlo method, is used to design three dimensional models for BWR fuel bundles at typical operating temperatures and pressure conditions. These models are used to determine the multiplication factor, pin-by-pin power distribution, axial power distribution, thermal neutron flux distribution, and axial thermal neutron flux. The moderator and coolant (water) are permitted to boil within the BWR core forming steam bubbles, so it is important to calculate the reactivity effect of voiding at different values. It is found that the hydride fuel bundle design can be simplified by eliminating water rods and replacing the control blade with control rods. UZrH{sub 1.6} fuel improves the performance of the BWR in different ways such as increasing the energy extracted per fuel assembly, reducing the uranium ore, and reducing the plutonium accumulated in the BWR through burnup.

  13. Simulations of ex-vessel fuel coolant interactions in a Nordic BWR using MC3D code

    Energy Technology Data Exchange (ETDEWEB)

    Thakre, S.; Ma, W. [Royal Institute of Technology, KTH. Div. of Nuclear Power Safety, Stockholm (Sweden)

    2013-08-15

    Nordic Boiling Water Reactors (BWRs) employ a drywell cavity flooding technique as a nuclear severe accident management strategy. In case of core melt accident where the reactor pressure vessel will fail and the melt will eject from the lower head and fall into a water pool, may be in the form of a continuous jet. It is assumed that the melt jet will fragment, quench and form a coolable debris bed into the water pool. The melt interaction with a water pool may cause an energetic steam explosion which creates a potential risk towards the integrity of containment, leading to fission products release into the atmosphere. The results of the APRI-7 project suggest that the significant damage to containment structures by steam explosion cannot be ruled according to the state-of-the-art knowledge about corresponding accident scenario. In the follow-up project APRI-8 (2012-2016) one of the goals of the KTH research is to resolve the steam explosion energetics (SEE) issue, developing a risk-oriented framework for quantifying conditional threats to containment integrity for a Nordic type BWR. The present study deals with the premixing and explosion phase calculations of a Nordic BWR dry cavity, using MC3D, a multiphase CFD code for fuel coolant interactions. The main goal of the study is the assessment of pressure buildup in the cavity and the impact loading on the side walls. The conditions for the calculations are used from the SERENA-II BWR case exercise. The other objective was to do the sensitivity analysis of the parameters in modeling of fuel coolant interactions, which can help to reduce uncertainty in assessment of steam explosion energetics. The results show that the amount of liquid melt droplets in the water (region of void<0.6) is maximum even before reaching the jet at the bottom. In the explosion phase, maximum pressure is attained at the bottom and the maximum impulse on the wall is at the bottom of the wall. The analysis is carried out using two different

  14. Potential for containment leak paths through electrical penetration assemblies under severe accident conditions. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    Sebrell, W.

    1983-07-01

    The leakage behavior of containments beyond design conditions and knowledge of failure modes is required for evaluation of mitigation strategies for severe accidents, risk studies, emergency preparedness planning, and siting. These studies are directed towards assessing the risk and consequences of severe accidents. An accident sequence analysis conducted on a Boiling Water Reactor (BWR), Mark I (MK I), indicated very high temperatures in the dry-well region, which is the location of the majority of electrical penetration assemblies. Because of the high temperatures, it was postulated in the ORNL study that the sealants would fail and all the electrical penetration assemblies would leak before structural failure would occur. Since other containments had similar electrical penetration assemblies, it was concluded that all containments would experience the same type of failure. The results of this study, however, show that this conclusion does not hold for PWRs because in the worst accident sequence, the long time containment gases stabilize to 350/sup 0/F. BWRs, on the other hand, do experience high dry-well temperatures and have a higher potential for leakage.

  15. THERMAL EVALUATION OF THE CONCEPTUAL 24 BWR UCF TUBE BASKET DESIGN DISPOSAL CONTAINER

    Energy Technology Data Exchange (ETDEWEB)

    T.L. Lotz

    1995-12-18

    This analysis is prepared by the Mined Geologic Disposal System (MGDS) Waste Package Development Department (WPDD) as specified in the Waste Package Implementation Plan (pp. 4-8,4-11,4-24,5-1, and 5-13; Ref. 5.10) and Waste Package Plan (pp. 3-15,3-17, and 3-24; Ref. 5.9). The design data request addressed herein is: (1) Characterize the conceptual 24 boiling water reactor (BWR) uncanistered fuel (UCF) waste package (WP) to show that the design is feasible for use in the MGDS environment. The purpose of this analysis is to respond to a concern that the long-term disposal thermal issues for the UCF waste package do not preclude UCF waste package compatibility with the MGDS. The objective of this analysis is to provide thermal parameter information for the conceptual UCF WP design under nominal MGDS repository conditions. The results are intended to show that the design has a reasonable chance to meet the MGDS design requirements for normal MGDS operation and to provide the required guidance to determining the major design issues for future design efforts. Future design efforts will focus on UCF design changes as further design and operations information becomes available.

  16. Standard technical specifications General Electric plants, BWR/6. Volume 1, Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-01

    This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS), Revision 1 for General Electric BWR/6 Plants. The changes reflected in Revision 1 resulted from the experience gained from license amendment applications to convert to these improved STS or to adopt partial improvements to existing technical specifications. This NUREG is the result of extensive public technical meetings and discussions between the Nuclear Regulatory Commission (NRC) staff and various nuclear power plant licensees, Nuclear Steam Supply System (NSSS) Owners Groups, NSSS vendors, and the Nuclear Energy Institute (NEI). The improved STS were developed based on the criteria in the Final Commission Policy Statement on Technical Specifications Improvements for Nuclear Power Reactors, dated July 22, 1993. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.10 of the improved STS.

  17. Standard technical specifications: General Electric plants, BWR/4. Volume 1, Revision 1: Specifications

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-04-01

    This report documents the results of the combined effort of the NRC and the industry to produce improved Standard Technical Specifications (STS), Revision 1 for General Electric BWR/4 Plants. The changes reflected in Revision 1 resulted from the experience gained from license amendment applications to convert to these improved STS or to adopt partial improvements to existing technical specifications. This NUREG is the result of extensive public technical meetings and discussions between the Nuclear Regulatory Commission (NRC) staff and various nuclear power plant licensees, Nuclear Steam Supply System (NSSS) Owners Groups, NSSS vendors, and the Nuclear Energy Institute (NEI). The improved STS were developed based on the criteria in the Final Commission Policy Statement on Technical Specifications Improvements for Nuclear Power Reactors, dated July 22, 1993. The improved STS will be used as the basis for individual nuclear power plant licensees to develop improved plant-specific technical specifications. This report contains three volumes. Volume 1 contains the Specifications for all chapters and sections of the improved STS. Volume 2 contains the Bases for Chapters 2.0 and 3.0, and Sections 3.1--3.3 of the improved STS. Volume 3 contains the Bases for Sections 3.4--3.10 of the improved STS.

  18. 3D analysis methods - Study and seminar[BWR safety analysis

    Energy Technology Data Exchange (ETDEWEB)

    Daaviittila, A. [Valtion Teknillinen Tutkimuskeskus (Finland)

    2003-10-01

    The first part of the report results from a study that was performed as a Nordic co-operation activity with active participation from Studsvik Scandpower and Westinghouse Atom in Sweden, and VTT in Finland. The purpose of the study was to identify and investigate the effects rising from using the 3D transient com-puter codes in BWR safety analysis, and their influence on the transient analysis methodology. One of the main questions involves the critical power ratio (CPR) calculation methodology. The present way, where the CPR calculation is per-formed with a separate hot channel calculation, can be artificially conservative. In the investigated cases, no dramatic minimum CPR effect coming from the 3D calculation is apparent. Some cases show some decrease in the transient change of minimum CPR with the 3D calculation, which confirms the general thinking that the 1D calculation is conservative. On the other hand, the observed effect on neutron flux behaviour is quite large. In a slower transient the 3D effect might be stronger. The second part of the report is a summary of a related seminar that was held on the 3D analysis methods. The seminar was sponsored by the Reactor Safety part (NKS-R) of the Nordic Nuclear Safety Research Programme (NKS). (au)

  19. Study on nuclear physics of high burn-up full MOX-BWR core

    Energy Technology Data Exchange (ETDEWEB)

    Shirakawa, Toshihisa; Okubo, Tsutomu; Ochiai, Masa-aki [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-08-01

    In this report, neutronics study of full Mixed-oxide (MOX) high burn-up BWR core is presented. Our design goals are about 3-year cycle length, four-batch refueling scheme and more than 100GWd/t fuel discharge burn-up. Base core configuration is 1,350MWe US version of ABWR with 9 x 9 type fuel assembly. Investigation of the reactor core has been carried out by arranging Gd{sub 2}O{sub 3} contents in fuel rods and changing water to fuel volume ratio (V{sub m}/V{sub f}) through the number of water rods or adjustment of fuel clad diameter. JAERI`s general purpose neutronics code system SRAC95 was used for two dimensional XY fuel assembly cell neutronics calculations. Calculated cases are for a comparatively high moderated fuel assembly with 9 water rods, a fuel assembly without water rods and a comparatively low moderated fuel assembly without water rods and with larger fuel clad diameter. All these 3 cases seem to achieve our design goals mentioned above. For the last case, three dimensional core burn-up calculation was performed by this code system. This case seems to attain a low linear power density and the operation with all control rod out. (author)

  20. Prevention of organic iodide formation in BWR`s

    Energy Technology Data Exchange (ETDEWEB)

    Karjunen, T. [Finnish Centre for Radiation and Nuclear Safety, Helsinki (Finland); Laitinen, T.; Piippo, J.; Sirkiae, P. [VTT Manufacturing Technology (Finland)

    1996-12-01

    During an accident, many different forms of iodine may emerge. Organic iodides, such as methyl iodide and ethyl iodide, are relatively volatile, and thus their appearance leads to increased concentration of gaseous iodine. Since organic iodides are also relatively immune to most accident mitigation measures, such as sprays and filters, they can affect the accident source term significantly even when only a small portion of iodine is in organic form. Formation of organic iodides may not be limited by the amount of organic substances available. Excessive amounts of methane can be produced, for example, during oxidation of boron carbide, which is used in BWR`s as a neutron absorber material. Another important source is cable insulation. In a BWR, a large quantity of cables is placed below the pressure vessel. Thus a large quantity of pyrolyse gases will be produced, should the vessel fail. Organic iodides can be formed as a result of many different reactions, but at least in certain conditions the main reaction takes place between an organic radical produced by radiolysis and elemental iodine. A necessary requirement for prevention of organic iodide production is therefore that the pH in the containment water pools is kept high enough to eliminate formation of elemental iodine. In a typical BWR the suppression pool water is usually unbuffered. As a result, the pH may be dominated by chemicals introduced during an accident. If no system for adding basic chemicals is operable, the main factor affecting pool water pH may be hydrochloric acid released during cable degradation. Should this occur, the conditions could be very favorable for production of elemental iodine and, consequently, formation of organic iodides. Although high pH is necessary for iodine retention, it could have also adverse effects. High pH may, for example, accelerate corrosion of containment materials and alter the characteristics of the solid corrosion products. (author) 6 figs., 1 tab., 13 refs.

  1. Parametric studies on containment thermal hydraulic loads during high pressure melt ejection in a BWR

    Energy Technology Data Exchange (ETDEWEB)

    Silde, A.; Lindholm, I. [VTT Energy, Espoo (Finland)

    1997-12-01

    The containment thermal hydraulic loads during high pressure melt ejection in a Nordic BWR are studied parametrically with the CONTAIN and the MELCOR codes. The work is part of the Nordic RAK-2 project. The containment analyses were divided into two categories according to composition of the discharged debris: metallic and oxidic debris cases. In the base case with highly metallic debris, all sources from the reactor coolant system to the containment were based on the MELCOR/BH calculation. In the base case with the oxidic debris, the source data was specified assuming that {approx} 15% of the whole core material inventory and 34,000 kg of saturated water was discharged from the reactor pressure vessel (RPV) during 30 seconds. In this case, the debris consisted mostly of oxides. The highest predicted containment pressure peaks were about 8.5 bar. In the scenarios with highly metallic debris source, very high gas temperature of about 1900 K was predicted in the pedestal, and about 1400 K in the upper drywell. The calculations with metallic debris were sensititive to model parameters, like the particle size and the parameters, which control the chemical reaction kinetics. In the scenarios with oxidic debris source, the predicted pressure peaks were comparable to the cases with the metallic debris source. The maximum gas temperatures (about 450-500 K) in the containment were, however, significantly lower than in the respective metallic debris case. The temperatures were also insensitive to parametric variations. In addition, one analysis was performed with the MELCOR code for benchmarking of the MELCOR capabilities against the more detailed CONTAIN code. The calculations showed that leak tightness of the containment penetrations could be jeopardized due to high temperature loads, if a high pressure melt ejection occurred during a severe accident. Another consequence would be an early containment venting. (au). 28 refs.

  2. El derecho a la integridad personal. Elementos para su análisis

    Directory of Open Access Journals (Sweden)

    María Isabel Afanador C.

    2002-01-01

    Full Text Available El presente ensayo se ocupa del estudio de los elementos esenciales del derecho a la integridad personal, desde la evolución histórica y normativa de su reconocimiento, así como del análisis crítico respecto de las más graves manifestaciones de su violación, tales como la tortura y la desaparición forzada de personas. El escrito está centrado no sólo en la fundamentación jurídica del tema, desde la perspectiva del Derecho Internacional de los Derechos Humanos (DIDH, sino que comprende el análisis político de la realidad colombiana en esta materia, en el contexto de una concepción democrática de los derechos humanos, sin negar que el problema pueda ser abordado y discutido desde otras perspectivas.

  3. Effect of anisotropic scattering in neutronics analysis of BWR assembly

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Toshikazu [Division of Sustainable Energy and Environmental Engineering, Graduate School of Engineering, Osaka University, Yamadaoka 2-1, Suita, Osaka 565-0571 (Japan)]. E-mail: takeda@nucl.eng.osaka-u.ac.jp; Okamoto, Toshiki [Division of Sustainable Energy and Environmental Engineering, Graduate School of Engineering, Osaka University, Yamadaoka 2-1, Suita, Osaka 565-0571 (Japan); Inoue, Akira [Division of Sustainable Energy and Environmental Engineering, Graduate School of Engineering, Osaka University, Yamadaoka 2-1, Suita, Osaka 565-0571 (Japan); Kosaka, Shinya [TEPCO Systems Corporation, 2-37-28 Eitai, Koutou-ku, Tokyo 135-0034 (Japan); Ikeda, Hideaki [TEPCO Systems Corporation, 2-37-28 Eitai, Koutou-ku, Tokyo 135-0034 (Japan)

    2006-11-15

    The anisotropic scattering effect to keff is studied for UO{sub 2} and MOX fueled BWR assemblies. The anisotropic scattering effect increases the assembly k {sub {infinity}} by 0.44% {delta}k for the UO{sub 2} assembly with 0% void fraction, and by 0.21% {delta}k for the MOX assembly with 0% void fraction. This is because the anisotropic scattering effect flattens the intra-assembly thermal flux, and the absorption rate in the surrounding water gap is decreased, but the absorption rates in the MOX fuel rods are increased compared to the UO{sub 2} rods. Therefore, the total decrease in absorption rates in the UO{sub 2} assembly is relatively large, and the k {sub {infinity}} is increased in the UO{sub 2} assembly. The dependence of the anisotropic scattering effect on the void fraction is investigated, and the significant difference of 0.62% {delta}k/k is found for the 0% and the 80% void fractions. The BWR assemblies with Gd rods are also considered. Furthermore, the usefulness of the transport cross section is investigated, and it is found that the transport cross section gives reasonable anisotropic scattering effect, though not satisfactory.

  4. Interveniência da integridade na relação entre idade e ansiedade face à morte em adultos idosos

    OpenAIRE

    Freitas, Pedro José do Amaral Ferreira de

    2009-01-01

    Dissertação de Mestrado apresentada no Instituto Superior de Psicologia Aplicada para obtenção de grau de Mestre na especialidade de Psicologia Clínica Baseando-se na teoria eriksoniana relativamente ao último estádio de desenvolvimento (integridade vs. desesepero), o presente trabalho tem como objectivo o estudo da interveniência da Integridade na relação entre a idade e a Ansiedade Face à Morte (AFM) em adultos idosos. Usou-se a Escala de Integridade (EI; Da Silva, 2009) e també...

  5. Characterization of noble metals deposits and oxides in conditions of BWR reactors; Caracterizacion de depositos de metales nobles y oxidos en condiciones de reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Arganis J, C.R.; Aguilar T, J.A.; Contreras R, A. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)

    2008-07-01

    The oxides deposited on steel 304l under normal chemistry conditions (NWC) and hydrogen chemistry (HWC) with presence of Zn, being that the first ones present hexagonal oxides of Hematite and the second bipyramidal crystals possibly Magnetite with traces of Zn. Deposits of Pt on the oxidized surfaces under NWC conditions were obtained, being glasses from 2 to 4 {mu}m and Pt-Rh deposits were obtained on the oxidized surfaces in presence of Zn, by its size its were not possible to observe them by scanning electron microscopy. The kinetics of the surfaces of Hematite and of the deposits of Pt it was measured by means of the Tafel extrapolation technique, being proven the catalytic effect of the Pt, even in sizes of 11 {mu}m. (Author)

  6. Actinides record, power calculations and activity for present isotopes in the spent fuel of a BWR; Historial de actinidos y calculos de potencia y actividad para isotopos presentes en el combustible gastado de un BWR

    Energy Technology Data Exchange (ETDEWEB)

    Enriquez C, P.; Ramirez S, J. R.; Lucatero, M. A., E-mail: pastor.enriquez@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2012-10-15

    The administration of spent fuel is one of the more important stages of the nuclear fuel cycle, and this has become a problem of supreme importance in countries that possess nuclear reactors. Due to this in this work, the study on the actinides record and present fission products to the discharge of the irradiated fuel in a light water reactor type BWR is shown, to quantify the power and activity that emit to the discharge and during the cooling time. The analysis was realized on a fuel assembly type 10 x 10 with an enrichment average of 3.69 wt % in U-235 and the assembly simulation assumes four cycles of operation of 18 months each one and presents an exposition of 47 G Wd/Tm to the discharge. The module OrigenArp of the Scale 6 code is the computation tool used for the assembly simulation and to obtain the results on the actinides record presents to the fuel discharge. The study covers the following points: a) Obtaining of the plutonium vector used in the fuel production of mixed oxides, and b) Power calculation and activity for present actinides to the discharge. The results presented in this work, correspond at the same time immediate of discharge (0 years) and to a cooling stage in the irradiated fuel pool (5 years). (Author)

  7. Solution to the transport equation with anisotropic dispersion in a BWR type assembly using the AZTRAN code; Solucion de la ecuacion de transporte con dispersion anisotropica en un ensamble tipo BWR usando el codigo AZTRAN

    Energy Technology Data Exchange (ETDEWEB)

    Chepe P, M. [Universidad Autonoma Metropolitana, Unidad Iztapalapa, San Rafael Atlixco No. 186, Col. Vicentina, 09340 Ciudad de Mexico (Mexico); Xolocostli M, J. V.; Gomez T, A. M. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Del Valle G, E., E-mail: liaison.web@gmail.com [IPN, Escuela Superior de Fisica y Matematicas, Av. IPN s/n, Col. San Pedro Zacatenco, 07730 Ciudad de Mexico (Mexico)

    2016-09-15

    Due to the current computing power, the deterministic codes for analyzing nuclear reactors that have been used for several years are becoming more relevant, since much more precise solution techniques can be used; the last century would have been very difficult, since memory and processor capacities were very limited or had high prices on the components. In this work we analyze the effect of the anisotropic dispersion of the effective dispersion section, compared to the isotropic dispersion. The anisotropy implementation was carried out in the AZTRAN transport code, which is part of the AZTLAN platform for nuclear reactors analysis (in development). The AZTRAN code solves the Boltzmann transport equation in one, two and three dimensions at steady state, using the multi-group technique for energy discretization, the RTN-0 nodal method in spatial discretization and for angular discretization the discrete ordinates without considering anisotropy originally. The effect of the anisotropy dispersion on the effective multiplication factor and the axial and radial power on a fuel assembly BWR type are analyzed. (Author)

  8. Feasibility study of boiling water reactor core based on thorium-uranium fuel concept

    Energy Technology Data Exchange (ETDEWEB)

    Nunez-Carrera, Alejandro [Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Barragan 779, Col Narvarte, 03020 Mexico D.F. (Mexico); Francois Lacouture, Juan Luis; Martin del Campo, Cecilia [Universidad Nacional Autonoma de Mexico, Facultad de Ingenieria, Paseo Cuauhnahuac 8532, Jiutepec, Mor. (Mexico); Espinosa-Paredes, Gilberto [Area de Ingenieria en Recursos Energeticos, Universidad Autonoma Metropolitana Iztapalapa, Apartado Postal 55-534, Mexico D.F. 09340 (Mexico)], E-mail: gepe@xanum.uam.mx

    2008-01-15

    The design of a boiling water reactor (BWR) equilibrium core using the thorium-uranium (blanket-seed) concept in the same integrated fuel assembly is presented in this paper. The lattice design uses the thorium conversion capability to {sup 233}U in a BWR spectrum. A core design was developed to achieve an equilibrium cycle of one effective full power year in a standard BWR with a reload of 104 fuel assemblies designed with an average {sup 235}U enrichment of 7.5 w/o in the seed sub-lattice. The main core operating parameters were obtained. It was observed that the analyzed parameters behave like those obtained in a standard BWR. The economic analysis shows that the fuel cycle cost of the proposed core design can be competitive with a standard uranium core design. Finally, a comparison of the toxicity of the spent fuel showed that the toxicity is lower in the thorium cycle than in other fuel cycles (UO{sub 2} and MOX uranium and plutonium) in the case of the once through cycle for light water reactors (LWR)

  9. Methods and results of a PSA level 2 for a German BWR of the 900 MWe class

    Energy Technology Data Exchange (ETDEWEB)

    Loffler, H.; Sonnenkalb, M. [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, Koln (Germany)

    2006-07-01

    On behalf of the federal Ministry for Environment, Nature Conservation and Reactor Safety (BMU) GRS has performed a PSA level 2 for a BWR type 69 NPP of the 900 MWe class, equipped with a N{sub 2} inerted steel containment and a pressure suppression system. Integral deterministic accident analyses have been performed with the computer code MELCOR 1.8.5. Additional analyses have been done for those events and phenomena which are not or not sufficiently covered by MELCOR. The probabilistic event tree analysis begins with the core damage states received from PSA level 1, and it ends with the definition of release categories and the determination of their frequencies. Uncertainties about the frequency of core damage states and about events during the accident progression are taken into account by means of Monte Carlo simulations. If there is a core damage state there is a high probability (>50 %) for a very high and rapid release of radionuclides into the environment. This high conditional probability is due to the very low probability to retain a partly destroyed core inside the reactor pressure vessel (RPV) and because the containment almost certainly fails at the bottom of the control rod drives room after melt release from the failed RPV. (authors)

  10. Development of an Input Model to MELCOR 1.8.5 for the Oskarshamn 3 BWR

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, Lars [Lentek, Nykoeping (Sweden)

    2006-05-15

    An input model has been prepared to the code MELCOR 1.8.5 for the Swedish Oskarshamn 3 Boiling Water Reactor (O3). This report describes the modelling work and the various files which comprise the input deck. Input data are mainly based on original drawings and system descriptions made available by courtesy of OKG AB. Comparison and check of some primary system data were made against an O3 input file to the SCDAP/RELAP5 code that was used in the SARA project. Useful information was also obtained from the FSAR (Final Safety Analysis Report) for O3 and the SKI report '2003 Stoerningshandboken BWR'. The input models the O3 reactor at its current state with the operating power of 3300 MW{sub th}. One aim with this work is that the MELCOR input could also be used for power upgrading studies. All fuel assemblies are thus assumed to consist of the new Westinghouse-Atom's SVEA-96 Optima2 fuel. MELCOR is a severe accident code developed by Sandia National Laboratory under contract from the U.S. Nuclear Regulatory Commission (NRC). MELCOR is a successor to STCP (Source Term Code Package) and has thus a long evolutionary history. The input described here is adapted to the latest version 1.8.5 available when the work began. It was released the year 2000, but a new version 1.8.6 was distributed recently. Conversion to the new version is recommended. (During the writing of this report still another code version, MELCOR 2.0, has been announced to be released within short.) In version 1.8.5 there is an option to describe the accident progression in the lower plenum and the melt-through of the reactor vessel bottom in more detail by use of the Bottom Head (BH) package developed by Oak Ridge National Laboratory especially for BWRs. This is in addition to the ordinary MELCOR COR package. Since problems arose running with the BH input two versions of the O3 input deck were produced, a NONBH and a BH deck. The BH package is no longer a separate package in the new 1

  11. BWR plant analyzer development at BNL (Brookhaven National Laboratory)

    Energy Technology Data Exchange (ETDEWEB)

    Wulff, W.; Cheng, H.S.; Mallen, A.N.

    1986-01-01

    An engineering plant analyzer has been developed at BNL for realistically and accurately simulating transients and severe abnormal events in BWR power plants. Simulations are being carried out routinely with high fidelity, high simulation speed, at low cost and with unsurpassed user convenience. The BNL Plant Analyzer is the only operating facility which (a) simulates more than two orders-of-magnitude faster than the CDC-7600 mainframe computer, (b) is accessible and fully operational in on-line interactive mode, remotely from anywhere in the US, from Europe or the Far East (Korea), via widely available IBM-PC compatible personal computers, standard modems and telephone lines, (c) simulates both slow and rapid transients seven times faster than real-time in direct access, and four times faster in remote access modes, (d) achieves high simulation speed without compromising fidelity, and (e) is available to remote access users at the low cost of $160 per hour.

  12. Overview of New Tools to Perform Safety Analysis: BWR Station Black Out Test Case

    Energy Technology Data Exchange (ETDEWEB)

    D. Mandelli; C. Smith; T. Riley; J. Nielsen; J. Schroeder; C. Rabiti; A. Alfonsi; Cogliati; R. Kinoshita; V. Pasucci; B. Wang; D. Maljovec

    2014-06-01

    Dynamic Probabilistic Risk Assessment (DPRA) methodologies couple system simulator codes (e.g., RELAP, MELCOR) with simulation controller codes (e.g., RAVEN, ADAPT). While system simulator codes accurately model system dynamics deterministically, simulation controller codes introduce both deterministic (e.g., system control logic, operating procedures) and stochastic (e.g., component failures, parameter uncertainties) elements into the simulation. Typically, a DPRA is performed by: 1) sampling values of a set of parameters from the uncertainty space of interest (using the simulation controller codes), and 2) simulating the system behavior for that specific set of parameter values (using the system simulator codes). For complex systems, one of the major challenges in using DPRA methodologies is to analyze the large amount of information (i.e., large number of scenarios ) generated, where clustering techniques are typically employed to allow users to better organize and interpret the data. In this paper, we focus on the analysis of a nuclear simulation dataset that is part of the Risk Informed Safety Margin Characterization (RISMC) Boiling Water Reactor (BWR) station blackout (SBO) case study. We apply a software tool that provides the domain experts with an interactive analysis and visualization environment for understanding the structures of such high-dimensional nuclear simulation datasets. Our tool encodes traditional and topology-based clustering techniques, where the latter partitions the data points into clusters based on their uniform gradient flow behavior. We demonstrate through our case study that both types of clustering techniques complement each other in bringing enhanced structural understanding of the data.

  13. The possibility and the effects of a steam explosion in the BWR lower head on recriticality of a BWR core

    Energy Technology Data Exchange (ETDEWEB)

    Sehgal, B.R.; Dinh, T.N. [Sehgal Consult (Sweden)

    2002-12-01

    The report describes an analysis considering a BWR postulated severe accident scenario during which the late vessel automatic depressurization brings the water below the level of the bottom core plate. The subsequent lack of ECCS leads to core heat up during which the control rods melt and the melt deposits on the core plate. At that point of time in the scenario, the core fuel bundles are still intact and the Zircaloy clad oxidation is about to start. The objective of the study is to provide the conditions of reflood into the hot core due to the level swell or a slug delivered from the lower head as the control rod melt drops into the water. These conditions are employed in the neutronic analysis with the RECRIT code to determine if the core recriticality may be achieved. (au)

  14. Simulation of the BWR experiments CORA-17 and CORA-28 using ATHLET-CD and assessment of BWR modelling. 1{sup st} Technical report. Validation and interpretation of the ATHLET-CD model basis; Simulation der SWR-Versuche CORA-17 und CORA-28 mit dem Programmsystem ATHLET-CD und Bewertung der SWR-Modellbasis. 1. Technischer Fachbericht. Validierung und Interpretation der ATHLET-CD Modellbasis

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmann, M.; Gremme, F.; Koch, M.K.

    2013-08-15

    The 1st Technical Report was prepared for the research project ''Validation and Interpretation of the ATHLET-CD Model Basis'' funded by the Federal Ministry of Economics and Technology (BMWi1501385) and carried out at the Chair of Energy Systems and Energy Economics at Ruhr-Universitaet Bochum (RUB). This report provides results of the simulation of the Boiling Water Reactor (BWR) experiments CORA-17 and -28 with ATHLET-CD Mod. 2.2A. The system code ATHLET-CD (Analysis of Thermal-hydraulics of Leaks and Transients - Core Degradation) is developed by the German Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH. Code results are compared to measurements in order to assess and to analyze the capabilities of the current code version with regard to the modeling of BWR components. The CORA test series was carried out between the years 1987 and 1993 at the former Kernforschungszentrum Karlsruhe (KfK), now Karlsruhe Institute of Technology (KIT). The investigations provided experimental data regarding the material behavior during the early phase of core degradation in Light Water Reactors (LWR). The tests CORA17 and -28 represented a typical BWR arrangement of the fuel rod bundle and provided insights about the bundle behavior during the quenching process (CORA-17) and regarding the influence of a preoxidized bundle (CORA-28), respectively. The simulation results are analyzed and discussed in terms of the thermal bundle behavior, the zirconium oxidation in steam and the resulting hydrogen generation as well as the material relocation. In particular, the recently extended modeling capabilities of the code in terms of the relocation of BWR components like the absorber blade and the canister wall are assessed. The analysis shows that the code captures the thermal behavior in good agreement in both experiments. An even enhanced reproduction of the test CORA-28 is obtained in comparison to a calculation using the previous code version ATHLET-CD Mod

  15. Radial optimization of a BWR fuel cell using genetic algorithms; Optimizacion radial de una celda de combustible BWR usando algoritmos geneticos

    Energy Technology Data Exchange (ETDEWEB)

    Martin del Campo M, C.; Carmona H, R.; Oropeza C, I.P. [UNAM, Paseo Cuauhnahuac 8532, 62550 Jiutepec, Morelos (Mexico)]. e-mail: cmcm@fi-b.unam.mx

    2006-07-01

    The development of the application of the Genetic Algorithms (GA) to the optimization of the radial distribution of enrichment in a cell of fuel of a BWR (Boiling Water Reactor) is presented. The optimization process it was ties to the HELIOS simulator, which is a transport code of neutron simulation of fuel cells that has been validated for the calculation of nuclear banks for BWRs. With heterogeneous radial designs can improve the radial distribution of the power, for what the radial design of fuel has a strong influence in the global design of fuel recharges. The optimum radial distribution of fuel bars is looked for with different enrichments of U{sup 235} and contents of consumable poison. For it is necessary to define the representation of the solution, the objective function and the implementation of the specific optimization process to the solution of the problem. The optimization process it was coded in 'C' language, it was automated the creation of the entrances to the simulator, the execution of the simulator and the extraction, in the exit of the simulator, of the parameters that intervene in the objective function. The objective function includes four parameters: average enrichment of the cell, average gadolinia concentration of the cell, peak factor of radial power and k-infinite multiplication factor. To be able to calculate the parameters that intervene in the objective function, the one evaluation process of GA was ties to the HELIOS code executed in a Compaq Alpha workstation. It was applied to the design of a fuel cell of 10 x 10 that it can be employee in the fuel assemble designs that are used at the moment in the Laguna Verde Nucleo electric Central. Its were considered 10 different fuel compositions which four contain gadolinia. Three heuristic rules that consist in prohibiting the placement of bars with gadolinia in the ends of the cell, to place the compositions with the smallest enrichment in the corners of the cell and to fix

  16. Nuclear reactor power monitoring device

    Energy Technology Data Exchange (ETDEWEB)

    Tarumi, Teruji; Oda, Naotaka; Goto, Yasushi; Ito, Toshiaki [Toshiba Corp., Kawasaki, Kanagawa (Japan); Mitsubori, Minehisa

    1997-07-11

    The present invention provides a nuclear power monitoring device which does not lose a safety protection function even upon occurrence of a single failure in an APRM system of a BWR type reactor. Namely, an APRM for inputting signals of local power region monitors (LPRM) has four channels. Each of the channels is constituted so as to be bypassed. With such a constitution, LPRM detector signals can be inputted one by one to each of the four channels of the APRM from each of the LPRM detector assembly. Accordingly, a common channel for LPRM detectors can be eliminated in a small-sized reactor. The number of signals of the LPRM detectors inputted to each of the channels of the APRM is increased in a large-scaled reactor. Since each of the APRM can be bypassed, even if a single failure of one APRM is caused during a predetermined maintenance, the monitoring can be conducted smoothly by bypassing other channel. As a result, a multiple safe-protection function can be ensured. (I.S.)

  17. MOX fuel assembly and reactor core

    Energy Technology Data Exchange (ETDEWEB)

    Aoyama, Motoo; Shimada, Hidemitsu; Kaneto, Kunikazu; Koyama, Jun-ichi; Uchikawa, Sadao [Hitachi Ltd., Tokyo (Japan); Izutsu, Sadayuki; Fujita, Satoshi

    1998-03-10

    MOX fuel assemblies containing fuel rods of mixed oxide (MOX) of uranium and plutonium are loaded to a reactor core of a BWR type reactor. The fuel assembly comprises lattice like arranged fuel rods, one large diameter water rod disposed at the central portion and a channel box surrounding them. An average enrichment degree A of fission plutonium of fuel rods arranged at the outermost layer region and an average enrichment degree B of fission plutonium of fuel rods arranged at the inner layer region satisfy the relation of B/A {>=} 2.2. It is preferable that the average enrichment degree C of fission plutonium of fuel rods arranged at the outermost corner portions and the enrichment degree A satisfy the relation: C/A {<=} 0.5. With such a constitution, even in a case where the MOX fuel assemblies and uranium fuel assemblies are disposed together, thermal margin can be improved. (I.N.)

  18. Analysis of the behavior of irradiated BWR fuel rod in storage dry conditions; Analisis del comportamiento de una barra combustible irradiada BWR en condiciones de almacenamiento en seco

    Energy Technology Data Exchange (ETDEWEB)

    Munoz, A.; Montes, D.; Ruiz-Hervias, J.; Munoz-Reja, C.

    2014-07-01

    In order to complete previous studies of creep on PWR sheath material, developed a joint experimental program by CSN, ENRESA and ENUSA about BWR (Zircaloy-2) sheath material. This program consisted in creep tests and then on the material under creep, compression testing diametral obtaining the permissible displacement of the sheath to break. (Author)

  19. Direct torus venting analysis for Chinshan BWR-4 plant with MARK-I containment

    Energy Technology Data Exchange (ETDEWEB)

    Yuann, Yng-Ruey, E-mail: ryyuann@iner.gov.tw

    2017-03-15

    Highlights: • Study the effectiveness of Direct Torus Venting System (DTVS) during extended SBO of 24 h for Chinshan MARK-I plant. • Containment response is analyzed by GOTHIC based on boundary conditions from RETRAN calculation. • Analyses are performed with and without DTVS, respectively. • Suppression pool is sub-divided and thermal stratification is observed. - Abstract: The Chinshan plant, owned by Taiwan Power Company, has twin units of BWR-4 reactor and MARK-I containment. Both units have been operating at rated core thermal power of 1840 MWt. The existing Direct Torus Venting System (DTVS) is the main system used for venting the containment during the extended station blackout event. The purpose of this paper is to study the effects of the DTVS venting on the response of the containment pressure and temperature. The reactor is depressurized by manually opening the safety relief valves (SRVs) during the SBO, which causes the mass and energy to be discharged into and heat up the suppression pool. The RETRAN model is used to calculate the Nuclear Steam Supply System (NSSS) response and generate the SRV blowdown conditions, including SRV pressure, enthalpy, and mass flow rate. These conditions are then used as the time-dependent boundary conditions for the GOTHIC code to calculate the containment pressure and temperature response. The DTVS model is established in the GOTHIC model based on the venting size, venting piping loss, venting initiation time, and venting source. The lumped volume model, 1-D coarse-mesh model, and 3-D coarse-mesh model are considered in the torus volume. The calculation is first done without DTVS venting to establish a reference basis. Then a case with DTVS available is performed. Comparison of the two cases shows that the existing DTVS design is effective in mitigating the severity of the containment pressure and temperature transients. The results also show that the 1-D coarse-mesh model may not be appropriate since a

  20. BWR Spent Nuclear Fuel Integrity Research and Development Survey for UKABWR Spent Fuel Interim Storage

    Energy Technology Data Exchange (ETDEWEB)

    Bevard, Bruce Balkcom [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Mertyurek, Ugur [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Belles, Randy [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Scaglione, John M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-10-01

    The objective of this report is to identify issues and support documentation and identify and detail existing research on spent fuel dry storage; provide information to support potential R&D for the UKABWR (United Kingdom Advanced Boiling Water Reactor) Spent Fuel Interim Storage (SFIS) Pre-Construction Safety Report; and support development of answers to questions developed by the regulator. Where there are gaps or insufficient data, Oak Ridge National Laboratory (ORNL) has summarized the research planned to provide the necessary data along with the schedule for the research, if known. Spent nuclear fuel (SNF) from nuclear power plants has historically been stored on site (wet) in spent fuel pools pending ultimate disposition. Nuclear power users (countries, utilities, vendors) are developing a suite of options and set of supporting analyses that will enable future informed choices about how best to manage these materials. As part of that effort, they are beginning to lay the groundwork for implementing longer-term interim storage of the SNF and the Greater Than Class C (CTCC) waste (dry). Deploying dry storage will require a number of technical issues to be addressed. For the past 4-5 years, ORNL has been supporting the U.S. Department of Energy (DOE) in identifying these key technical issues, managing the collection of data to be used in issue resolution, and identifying gaps in the needed data. During this effort, ORNL subject matter experts (SMEs) have become expert in understanding what information is publicly available and what gaps in data remain. To ensure the safety of the spent fuel under normal and frequent conditions of wet and subsequent dry storage, intact fuel must be shown to: 1.Maintain fuel cladding integrity; 2.Maintain its geometry for cooling, shielding, and subcriticality; 3.Maintain retrievability, and damaged fuel with pinhole or hairline cracks must be shown not to degrade further. Where PWR (pressurized water reactor) information is

  1. Analysis of core degradation and relocation phenomena and scenarios in a Nordic-type BWR

    Energy Technology Data Exchange (ETDEWEB)

    Galushin, Sergey, E-mail: galushin@kth.se; Kudinov, Pavel, E-mail: pkudinov@kth.se

    2016-12-15

    Highlights: • A data base of the debris properties in lower plenum generated using MELCOR code. • The timing of safety systems has significant effect on the relocated debris properties. • Loose coupling between core relocation and vessel failure analyses was established. - Abstract: Severe Accident Management (SAM) in Nordic Boiling Water Reactors (BWR) employs ex-vessel cooling of core melt debris. The melt is released from the failed vessel and poured into a deep pool of water located under the reactor. The melt is expected to fragment, quench, and form a debris bed, coolable by a natural circulation and evaporation of water. Success of the strategy is contingent upon melt release conditions from the vessel and melt-coolant interaction that determine (i) properties of the debris bed and its coolability (ii) potential for energetic melt-coolant interactions (steam explosions). Risk Oriented Accident Analysis Methodology (ROAAM+) framework is currently under development for quantification of the risks associated with formation of non-coolable debris bed and occurrence of steam explosions, both presenting a credible threats to containment integrity. The ROAAM+ framework consist of loosely coupled models that describe each stage of the accident progression. Core relocation analysis framework provides initial conditions for melt vessel interaction, vessel failure and melt release frameworks. The properties of relocated debris and melt release conditions, including in-vessel and ex-vessel pressure, lower drywell pool depth and temperature, are sensitive to the accident scenarios and timing of safety systems recovery and operator actions. This paper illustrates a methodological approach and relevant data for establishing a connection between core relocation and vessel failure analysis in ROAAM+ approach. MELCOR code is used for analysis of core degradation and relocation phenomena. Properties of relocated debris are obtained as functions of the accident scenario

  2. Pellet-Cladding Mechanical Interaction Failure Threshold for Reactivity Initiated Accidents for Pressurized Water Reactors and Boiling Water Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Beyer, Carl E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Geelhood, Kenneth J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2013-06-01

    Pacific Northwest National Laboratory (PNNL) has been requested by the U.S. Nuclear Regulatory Commission to evaluate the reactivity initiated accident (RIA) tests that have recently been performed in the Nuclear Safety Research Reactor (NSRR) and CABRI (French research reactor) on uranium dioxide (UO2) and mixed uranium and plutonium dioxide (MOX) fuels, and to propose pellet-cladding mechanical interaction (PCMI) failure thresholds for RIA events. This report discusses how PNNL developed PCMI failure thresholds for RIA based on least squares (LSQ) regression fits to the RIA test data from cold-worked stress relief annealed (CWSRA) and recrystallized annealed (RXA) cladding alloys under pressurized water reactor (PWR) hot zero power (HZP) conditions and boiling water reactor (BWR) cold zero power (CZP) conditions.

  3. Technology, safety and costs of decommissioning a reference boiling water reactor power station. Volume 2. Appendices. Technical report, September 1977-October 1979

    Energy Technology Data Exchange (ETDEWEB)

    Oak, H.D.; Holter, G.M.; Kennedy, W.E. Jr.; Konzek, G.J.

    1980-06-01

    Technology, safety and cost information is given for the conceptual decommissioning of a large (1100MWe) boiling water reactor (BWR) power station. Three approaches to decommissioning, immediate dismantlement, safe storage with deferred dismantlement and entombment, were studied to obtain comparisons between costs, occupational radiation doses, potential dose to the public and other safety impacts. It also shows the sensitivity of decommissioning safety and costs to the power rating of a BWR in the range of 200 to 1100 MWE. This volume contains the appendices.

  4. Preliminary Assessment of the Possible BWR Core/Vessel Damage States for Fukushima Daiichi Station Blackout Scenarios Using RELAP/SCDAPSIM

    Directory of Open Access Journals (Sweden)

    C. M. Allison

    2012-01-01

    Full Text Available Immediately after the accident at Fukushima Daiichi, Innovative Systems Software and other members of the international SCDAP Development and Training Program started an assessment of the possible core/vessel damage states of the Fukushima Daiichi Units 1–3. The assessment included a brief review of relevant severe accident experiments and a series of detailed calculations using RELAP/SCDAPSIM. The calculations used a detailed RELAP/SCDAPSIM model of the Laguna Verde BWR vessel and related reactor cooling systems. The Laguna Verde models were provided by the Comision Nacional de Seguridad Nuclear y Salvaguardias, the Mexican nuclear regulatory authority. The initial assessment was originally presented to the International Atomic Energy Agency on March 21 to support their emergency response team and later to our Japanese members to support their Fukushima Daiichi specific analysis and model development.

  5. Cerenkov Characteristics of BWR Assemblies using a Prototype DCVD with a Back-Illuminated CCD. Prepared for the Canadian Safeguards Support Program and the Swedish Support Program

    Energy Technology Data Exchange (ETDEWEB)

    Chen, J.D.; Gerwing, A.F. [Channel Systems Inc., Pinawa MA (Canada); Maxwell, R. [Canadian Nuclear Safety Commission, Ottawa, ON (Canada); Larsson, M.; Axell, K.; Hildingsson, L. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden); Lindberg, B. [LENS-TECH AB, Skellefteaa (Sweden); Sundkvist, E. [Teleca Design and Development, Stockholm (Sweden)

    2003-11-01

    The Canadian and Swedish Safeguards Support Programs have developed a prototype Digital Cerenkov Viewing Device (DCVD) to verify spent fuel. Field measurements in Swedish nuclear power reactor fuel bays on BWR fuel and non-fuel assemblies resulted in new Cerenkov information that offers the possibility of computer-assisted verification of spent-fuel assemblies. A number of fuel assemblies with missing fuel rods were examined. The missing fuel rods are easily detected when not hidden under the lifting handle of the fuel assembly. Initial studies of off-angle viewing of these assemblies show promise for the detection of the missing fuel rods under the lifting handle. The quantitative nature of the charge-coupled device was examined. A number of procedures were developed to quantify parameters such as image intensity and alignment (collimation) of fuel and no fuel assemblies. The quantitative studies on fuel assembly intensity as a function of cooling time showed excellent agreement with the theoretical calculations.

  6. H Reactor

    Data.gov (United States)

    Federal Laboratory Consortium — The H Reactor was the first reactor to be built at Hanford after World War II.It became operational in October of 1949, and represented the fourth nuclear reactor on...

  7. Un marco conceptual y analítico para estimar la integridad ecológica a escala de paisaje

    Directory of Open Access Journals (Sweden)

    Gómez Sal, A.

    2008-02-01

    Full Text Available A conceptual and analytical framework to assess ecological integrity at a landscape level. A concep tual and methodological approach for the ecological integrity analysis at landscape level is presented. The aim is providing a tool for land planning and nature conservation. With this purpose the meaning of integrity and related concepts are discussed, and a model to evaluate landscape integrity by a comprehensive scheme is proposed. The first index is based in metrics of landscape ecology theory (connectivity, cover of both conservation areas and human managed land, etc. to evaluate the different ecosystem fragments pattern. The second one, an ecosystems integrity index, is focused to evaluate remnants with a structure close to maturity and evaluates the mathematical distance to a reference hypothetical composition. Finally, the agricultural area is evaluated by a coherence index, with emphasis in ecological processes but also including the natural structures with conservation functions. These indexes are combined in a model that facilitates the joint consideration of their values and the comparison with theoretical scenarios. The model allows us to develop a concurrent management of relevant variables that usually are associated to different environmental qualities. Because of its characteristics and the intermediate scale of application, the model constitutes an important tool for matching ecosystem integrity and land planning. Both are actions and concept and relevant for nature conservation and landscape management, but in general independently considered.El trabajo constituye una aproximación conceptual y metodológica para el análisis de la integridad ecológica, como instrumento aplicable a la planificación del territorio y la conservación de la naturaleza a escala de paisaje. Con dicho fin se discuten las acepciones de integridad y conceptos próximos y se presenta un modelo de evaluación que considera la integridad del paisaje como

  8. Recent performance experience with US light water reactor self-actuating safety and relief valves

    Energy Technology Data Exchange (ETDEWEB)

    Hammer, C.G.

    1996-12-01

    Over the past several years, there have been a number of operating reactor events involving performance of primary and secondary safety and relief valves in U.S. Light Water Reactors. There are several different types of safety and relief valves installed for overpressure protection of various safety systems throughout a typical nuclear power plant. The following discussion is limited to those valves in the reactor coolant systems (RCS) and main steam systems of pressurized water reactors (PWR) and in the RCS of boiling water reactors (BWR), all of which are self-actuating having a setpoint controlled by a spring-loaded disk acting against system fluid pressure. The following discussion relates some of the significant recent experience involving operating reactor events or various testing data. Some of the more unusual and interesting operating events or test data involving some of these designs are included, in addition to some involving a number of similar events and those which have generic applicability.

  9. Validation of reactor noise linear stability methods by means of advanced stochastic differential equation models

    Energy Technology Data Exchange (ETDEWEB)

    Munoz-Cobo, J.L., E-mail: jlcobos@iqn.upv.es [Instituto de Ingenieri' a Energetica, Universidad Politecnica de Valencia, Camino de Vera 14, Valencia 46022 (Spain); Montesinos, M.E. [Instituto de Ingenieri' a Energetica, Universidad Politecnica de Valencia, Camino de Vera 14, Valencia 46022 (Spain); Pena, J. [Departamento de Matematica Aplicada, Universidad Politecnica de Valencia, Valencia (Spain); Escriva, A.; Gonzalez, C. [Instituto de Ingenieri' a Energetica, Universidad Politecnica de Valencia, Camino de Vera 14, Valencia 46022 (Spain); Melara, J. [IBERDROLA Ingenieri' a y Construccion, Avenida Manoteras 20, Madrid 28050 (Spain)

    2011-07-15

    Highlights: > We study validation methods for stability monitoring of BWR. > We generate synthetic signals from BWR reduced order models with previously known decay ratio. > Parametric and non parametric methods are used for the prediction of the stability. > We show the optimal method for filtering in the evaluation of the decay ratio. - Abstract: The aim of this paper is to show a validation method of a stability monitor using a BWR model with multiple Wiener noise sources, of additive and multiplicative nature. This model is solved using the modern methods to integrate stochastic differential equation systems, that are based on the stochastic Ito-Taylor expansion, and developed by Kloeden and Platen (1995), Kloeden et al. (1994). The synthetic signals generated with this BWR reduced order model with multiple Wiener processes are then used to obtain what are the optimal ways of filtering the signals for the different methods to estimate the decay ration (DR) and the natural frequency ({omega}) of the system. Also, for each DR estimation method, we study what is the optimal combination of algorithms to obtain the order and coefficients of the AR model that yields the best prediction of the reactor stability parameters for a broad range of DR values.

  10. Doença Terminal: A Construção da Integridade Familiar no Cuidador Idoso

    Directory of Open Access Journals (Sweden)

    Filipa Daniela Marques

    2017-08-01

    Full Text Available ObjetivosCuidar de uma pessoa no fim da vida é um evento cada vez mais comum e constitui um desafio a nível físico, emocional, relacional e desenvolvimental. A integridade familiar, processo emocional caraterizado por sentimentos de conexão, continuidade e pertença na família, constitui um desafio normal no desenvolvimento das pessoas idosas, influenciado por fatores do sistema familiar. Este estudo explora as experiências de pessoas idosas cuidadoras principais de familiares com doença terminal e analisa a sua influência na construção da integridade familiar.MétodoFoi administrada uma entrevista semiestruturada 10 cuidadoras familiares (65 a 80 anos.ResultadosOs resultados indicam que a prestação de cuidados familiares a pessoas com doença terminal constitui uma oportunidade de manifestação de apoio/responsabilidade familiar. Emergem especificidades relacionadas com o ato de cuidar que contribuem para o desenvolvimento da integridade familiar, nomeadamente: i sentimentos de utilidade que alimentam o dever cumprido; ii transmissão de um legado familiar simbólico (pautado pela ajuda ao próximo; iii divisão de tarefas e responsabilidade familiar que garantem a perceção do apoio recebido e a libertação do ato de cuidar.ConclusãoConclusão este estudo contribui para a valorização do cuidador familiar idoso e do sistema familiar como um todo, enaltecendo as alterações na configuração e dinâmica familiar.

  11. TOBI: A nonlinear model for boiling water reactor stability analysis

    Energy Technology Data Exchange (ETDEWEB)

    Wehle, F. (Siemens/KWU, Offenbach (West Germany)); Pruitt, D.W.

    1990-06-01

    The magnitude and the divergent nature of the oscillations during the LaSalle unit 2 nuclear power plant even on March 9, 1988, renewed concern about the state of knowledge on boiling water reactor (BWR) instabilities and was followed by many activities, e.g., the Idaho Stability Symposium. For appropriate representation of the physical processes, typical BWR time-domain stability calculations with, e.g., TRAC, RETRAN, or THERMIT require a large number of axial nodes and are very costly with regard to computer time. Linear models are inexpensive, but only valid as long as the parameters have no large deviation from the reference operating conditions. The objective of this work is the development of a physical model that is applicable for stability analysis in the nonlinear regime, but without the disadvantage of numerical problems and excessive computing times. The basic concept of the model TOBI is the integral study of the interaction between the time-dependent single- and two-phase regions. A series of calculations for purely thermal-hydraulic systems and BWRs has shown that TOBI is a convenient tool for stability analysis. Because of the simple but physically realistic modeling, it is very helpful in achieving an improved understanding of the mechanisms that affect BWR stability, and it is inexpensive, with regard to computer time, to perform extensive parameter sensitivity studies, even in the nonlinear regime.

  12. Development of controllers with high reliability for BWR plant

    Energy Technology Data Exchange (ETDEWEB)

    Asami, K.; Iida, H.; Eki, Y.; Hirose, M.; Ito, T. (Hitachi Ltd., Tokyo (Japan))

    1980-09-01

    Owing to the problems in system operation due to recent energy situation and the increase of nuclear power generation, high reliability and high rate of operation are required for nuclear power stations. In Hitachi Ltd., in order to meet these needs, efforts were exerted positively to make the controllers for BWR plants reliable. In this paper, three representative examples among them are described. The digital type flow rate control system for feed water recirculation ''D-FRC'' and the digital, electronic hydraulic type turbine control system ''D-EHC'' were developed by applying digital control technology and multiplication techniques, aiming at the high reliability of the most important control systems for nuclear power stations. The analog trip module enabled to attain high reliability and to reduce radiation exposure by improving preventive maintainability. Owing to the recent energy situation, the needs of safety and the high rate of operation in nuclear power stations have increased, but the attainment of high reliability in hardwares only has its limit, and the high reliability of systems is required. The measures for improving the reliability, the constitution of the D-FRC and its watching and diagnosing functions, the achievement of high quality control and the outline of the D-EHC and the analog trip module are described.

  13. Beta and gamma dose calculations for PWR and BWR containments

    Energy Technology Data Exchange (ETDEWEB)

    King, D.B.

    1989-07-01

    Analyses of gamma and beta dose in selected regions in PWR and BWR containment buildings have been performed for a range of fission product releases from selected severe accidents. The objective of this study was to determine the radiation dose that safety-related equipment could experience during the selected severe accident sequences. The resulting dose calculations demonstrate the extent to which design basis accident qualified equipment could also be qualified for the severe accident environments. Surry was chosen as the representative PWR plant while Peach Bottom was selected to represent BWRs. Battelle Columbus Laboratory performed the source term release analyses. The AB epsilon scenario (an intermediate to large LOCA with failure to recover onsite or offsite electrical power) was selected as the base case Surry accident, and the AE scenario (a large break LOCA with one initiating event and a combination of failures in two emergency cooling systems) was selected as the base case Peach Bottom accident. Radionuclide release was bounded for both scenarios by including spray operation and arrested sequences as variations of the base scenarios. Sandia National Laboratories used the source terms to calculate dose to selected containment regions. Scenarios with sprays operational resulted in a total dose comparable to that (2.20 /times/ 10/sup 8/ rads) used in current equipment qualification testing. The base case scenarios resulted in some calculated doses roughly an order of magnitude above the current 2.20 /times/ 10/sup 8/ rad equipment qualification test region. 8 refs., 23 figs., 12 tabs.

  14. Reactor-specific spent fuel discharge projections, 1987-2020

    Energy Technology Data Exchange (ETDEWEB)

    Walling, R.C.; Heeb, C.M.; Purcell, W.L.

    1988-03-01

    The creation of five reactor-specific spent fuel data bases that contain information on the projected amounts of spent fuel to be discharged from U.S. commercial nuclear reactors through the year 2020 is described. The data bases contain detailed spent fuel information from existing, planned, and projected pressurized water reactors (PWR) and boiling water eactors (BWR), and one existing high temperature gas reactor (HTGR). The projections are based on individual reactor information supplied by the U.S. reactor owners. The basic information is adjusted to conform to Energy Information Administration (EIA) forecasts for nuclear installed capacity, generation, and spent fuel discharged. The EIA cases considered are: No New Orders (assumes increasing burnup), No New Orders with No Increased Burnup, Upper Reference (assumes increasing burnup), Upper Reference with No Increased Burnup, and Lower Reference (assumes increasing burnup). Detailed, by-reactor tables are provided for annual discharged amounts of spent fuel, for storage requirements assuming maximum at-reactor storage, and for storage requirements assuming maximum at-reactor storage plus intra-utility transshipment of spent fuel. 8 refs., 8 figs., 10 tabs.

  15. Reactor-specific spent fuel discharge projections: 1986 to 2020

    Energy Technology Data Exchange (ETDEWEB)

    Heeb, C.M.; Walling, R.C.; Purcell, W.L.

    1987-03-01

    The creation of five reactor-specific spent fuel data bases that contain information on the projected amounts of spent fuel to be discharged from US commercial nuclear reactors through the year 2020 is described. The data bases contain detailed spent-fuel information from existing, planned, and projected pressurized water reactors (PWR) and boiling water reactors (BWR). The projections are based on individual reactor information supplied by the US reactor owners. The basic information is adjusted to conform to Energy Information Agency (EIA) forecasts for nuclear installed capacity, generation, and spent fuel discharged. The EIA cases considered are: (1) No new orders with extended burnup, (2) No new orders with constant burnup, (3) Upper reference (which assumes extended burnup), (4) Upper reference with constant burnup, and (5) Lower reference (which assumes extended burnup). Detailed, by-reactor tables are provided for annual discharged amounts of spent fuel, for storage requirements assuming maximum-at-reactor storage, and for storage requirements assuming maximum-at-reactor plus intra-utility transshipment of spent fuel. 6 refs., 8 figs., 8 tabs.

  16. Ética nos negócios e ética pessoal: uma questão de integridade

    OpenAIRE

    Ventura, Adriana Miguel

    2010-01-01

    Este trabalho aborda os conceitos de Ética nos Negócios e Ética Pessoal, usando como base a Ética das Virtudes de Robert Solomon, oriunda da abordagem Aristotélica. Discorre sobre conceitos como Valores, Atitudes e Comportamentos, bem como Dissonância Cognitiva e Tomada de Decisão. A coerência da Ética nos Negócios e da Ética Pessoal leva à integridade, a maior das virtudes. Com base no referencial teórico, foi realizada uma pesquisa que tinha por objetivo verificar a coerência entre os compo...

  17. INTEGRIDADE TISSULAR PREJUDICADA, FATORES RELACIONADOS E CARACTERÍSTICAS DEFINIDORAS EM PESSOAS COM ÚLCERAS VASCULARES

    OpenAIRE

    Suelen Gomes Malaquias; Maria Márcia Bachion; Marlene Andrade Martins; Cynthia Assis Barros Nunes; Gilson de Vasconcelos Torres; Lilian Varanda Pereira

    2014-01-01

    Se objetivó analizar factores relacionados, características determinantes en el deterioro de la integridad tisular en personas con úlceras vasculares y comparar los promedios de los factores entre grupos que presentaban diferentes grados de comprometimiento tisular. Pesquisa transversal, realizada de febrero – agosto/ 2009, en la red municipal de salud de Goiânia, utilizándose entrevista, examen clínico y registro fotográfico de la lesión. Para el análisis se utilizó frecuencia simple y porce...

  18. Analysis of core stability measurement data of advanced 9 x 9 fuel assembly in a BWR core

    Energy Technology Data Exchange (ETDEWEB)

    Tsuda, Katsuhiro; Itami, Akira; Kubo, Yuichiro; Shakudo, Taketomi [Nuclear Fuel Industries Ltd., Tokyo (Japan); Kreuter, D.; Anegawa, Takafumi; Kitamura, Hideya; Ishikawa, Masumi

    1997-05-01

    The core stability measurements were taken during the cycle-9 startup of the 1,300 MWe BWR, Kernkraftwerk Kruemmel (KKK). The core contained advanced 9 x 9 type high burn-up design reload fuel with a higher enrichment than current 8 x 8 fuel. A design feature of the advanced 9 x 9 fuel assembly (FA) is a large square water channel for enhanced neutron moderation. The measurement data as a function of core flow and power showed almost the same stability characteristics as those of the past measurement during the cycle-3 startup of the KKK core with the 8 x 8 FA. The local power range monitors (LPRM) detected neutron flux oscillations in both core-wide in-phase and half-core out-of-phase modes. The frequency-domain stability analysis using the STAIF-PK code well reproduced the measurement result that the onset of unstable operation in KKK first occurs when about half of the reactor internal pumps are operating and the other half are stopped. The stability performance of the advanced 9 x 9 FA in the core was compared with the 8 x 8 FA by a design parameter analysis with respect to thermal-hydraulic and neutronic design. It has been demonstrated by the analysis that the stability performance of the advanced 9 x 9 FA is comparable with current 8 x 8 FA. (author)

  19. Effect of Nitrogen Addition in 304 L Stainless Steel on the IGSCC Crack Growth Rate in Simulated BWR Environment

    Science.gov (United States)

    Roychowdhury, S.; Kain, V.; Prasad, R. C.

    Intergranular Stress Corrosion Cracking (IGSCC) in austenitic Stainless Steels (SS) in Boiling Water Reactor (BWR) operating conditions have been reported worldwide. Nitrogen containing Stainless Steel is used in BWRs and it can affect IGSCC behavior. In this investigation type 304L stainless steel with two different levels of nitrogen was evaluated in the sensitized and non-sensitised strain-hardened condition. Experiments were carried out in high temperature water with controlled dissolved oxygen. In the sensitised condition, the Crack Growth Rate (CGR) reduced and in the non-sensitised strain-hardened condition the CGR increased with increase in nitrogen level in SS. Transmission electron microscopic (TEM) investigations of the as-rolled SS and the SS after tensile testing at 288 °C indicated that rolling resulted in higher grain boundary strain which is a possible cause for higher CGR in the SS with higher nitrogen. Nitrogen did not have a noticeable effect on the deformation mechanism, for the SS after tensile testing at 288 °C, and the dislocation structures observed were similar for both the SS.

  20. Coretran/Vipre assembly critical power assessment against Nupec BWR experiments

    Energy Technology Data Exchange (ETDEWEB)

    Aounallah, Y. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    2001-07-01

    This study has been performed, in the framework of the STARS project, to assess CORETRAN-01/VIPRE-02 code capability to predict critical heat flux conditions for BWR fuel assemblies. The assessment is based on comparisons of the code results with the NUPEC steady-state critical power measurements on full-scale assemblies tested under a range of flow conditions. Two assembly types were considered, the standard BWR 8 x 8 and the so-called ''high-burnup'' assembly, similar to GE-10. Code modelling options that have a significant impact on the results have been identified, along with code limitations. (author)

  1. Simplified system for the pressure control of a Nucleo electric central of the BWR type; Sistema simplificado para el control de presion de una central Nucleoelectrica del tipo BWR

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez J, J. [FI-UNAM, DEPFI Campus Morelos, Jiutepec, Morelos (Mexico)

    2003-07-01

    One of the main preoccupations of the electric power generator stations is the appropriate operation of the same ones. The operators must be qualified to respond in an adequate way and to be able to take to these power stations to an optimal, sure and stable operation condition under any circumstance. The Laboratory of Analysis in Nuclear Reactors Engineering (LAIRN) of the Engineering Faculty of UNAM (Fl) in collaboration with the International Atomic Energy Agency (IAEA), it develops an interactive classroom simulator in which simulations of the phenomena which take place in a nuclear power station are executed. The classroom simulator bases its operation on specialized nuclear codes feeding interactive graphic unfolding with those that it is possible to make a monitoring, supervision and control of the behavior of the power station under any operation regime, either in normal operation, transitory events or postulated accident sequence. The development of this classroom simulator includes a modular and re configurable structure. Due to it is indispensable to count with a higher inter activity with the system it is included the simulation of the control system of the plant and inside the same, one of those more important it is the reactor pressure control system. The present work describes the conceptual design and the used methodology for the development and implementation in the simulator of a simplified model of the pressure control system for a BWR generic central. The reach of the development will allow to accomplish the necessary tests to demonstrate that this has an adequate performance according to the carried out simplifications. (Author)

  2. Integridad y desprecio. Motivos básicos de una concepción de la moral desde la teoría del reconocimiento

    Directory of Open Access Journals (Sweden)

    Hünneth, Axel

    1992-05-01

    Full Text Available Not available.

    Si se admite con Emst Bloch que la completa integridad del hombre, su dignidad, sólo se alcanza estableciendo una adecuada protección ante los distintos modos de ofensa y de desprecio personal, entonces eso significa a la inversa que la integridad de la persona humana depende constitutivamente de la experiencia de reconocimiento intersubjetivo. El presente texto quiere aclarar esa conexión premisa propia de una teoría normativa del reconocimiento recíproco, entre desprecio e integridad humana que Bloch sugirió pero no desarrolló, para así poder introducir una tesis fuerte de sociología moral: la experiencia del desprecio personal representa un impulso moral en el proceso de desarrollo de la sociedad, pues el progreso moral es el resultado de la lucha por el reconocimiento.

  3. Study of intermediate configurations during the fuel reload in BWRs; Estudio de configuraciones intermedias durante la recarga de combustible en BWR's

    Energy Technology Data Exchange (ETDEWEB)

    Fuentes M, L.; Castillo M, J. A.; Ortiz S, J. J.; Perusquia del C, R. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Jacinto C, S., E-mail: luis.fuentes@inin.gob.mx [Universidad Autonoma del Estado de Yucatan, Calle 60 No. 491-A por 57, 97000 Merida, Yucatan (Mexico)

    2012-10-15

    The criticality state of the core of a boiling water reactor (BWR) was evaluated, during the reload process for the intermediate states between the load pattern of cycle end and the beginning of the next, using the information of the load pattern of the operation cycles 13 and 14 of Unit 1 of the nuclear power plant of Laguna Verde. For this evaluation the codes CASMO-4 and Simulate-3 for conditions of the core in cold were used. The strategy consisted on moving assemblies with 4 burned cycles of the reactor core. Later on were re situated the remaining assemblies, placing them in the positions to occupy in the next operation cycle. Finally, was carried out the assemblies load of fresh fuel. In each realized change, it was observing the behavior of the k-effective value that is the parameter used to evaluate the criticality state of each state of the core change. In a second stage, was designed a program that builds in automatic way each one of the intermediate cores and also analyzes the criticality state of the reactor core after each withdrawal, re situated and load of fuel assemblies. (Author)

  4. Validation and Benchmarking of Westinghouse BWR lattice physics methods

    OpenAIRE

    Luszczek, Karol

    2015-01-01

    A lattice physics code is a vital tool, forming a base of reactor coreanalysis. It enables the neutronic properties of the fuel assembly to becalculated and generates a proper set of data to be used by a 3-D full coresimulator. Due to advancement and complexity of modern Boiling WaterReactor assembly designs, a new deterministic lattice physics codeis being developed at Westinghouse Sweden AB, namely PHOENIX5.Each time a new code is written, its methodology of solving the neutrontransport equ...

  5. A non-linear reduced order methodology applicable to boiling water reactor stability analysis

    Energy Technology Data Exchange (ETDEWEB)

    Prill, Dennis Paul

    2013-12-06

    Thermal-hydraulic coupling between power, flow rate and density, intensified by neutronics feedback are the main drivers of boiling water reactor (BWR) stability behavior. High-power low-flow conditions in connection with unfavorable power distributions can lead the BWR system into unstable regions where power oscillations can be triggered. This important threat to operational safety requires careful analysis for proper understanding. Analyzing an exhaustive parameter space of the non-linear BWR system becomes feasible with methodologies based on reduced order models (ROMs), saving computational cost and improving the physical understanding. Presently within reactor dynamics, no general and automatic prediction of high-dimensional ROMs based on detailed BWR models are available. In this thesis a systematic self-contained model order reduction (MOR) technique is derived which is applicable for several classes of dynamical problems, and in particular to BWRs of any degree of details. Expert knowledge can be given by operational, experimental or numerical transient data and is transfered into an optimal basis function representation. The methodology is mostly automated and provides the framework for the reduction of various different systems of any level of complexity. Only little effort is necessary to attain a reduced version within this self-written code which is based on coupling of sophisticated commercial software. The methodology reduces a complex system in a grid-free manner to a small system able to capture even non-linear dynamics. It is based on an optimal choice of basis functions given by the so-called proper orthogonal decomposition (POD). Required steps to achieve reliable and numerical stable ROM are given by a distinct calibration road-map. In validation and verification steps, a wide spectrum of representative test examples is systematically studied regarding a later BWR application. The first example is non-linear and has a dispersive character

  6. Desarrollo e implementación de una metodología para la evaluación de integridad en pozos con calentamiento eléctrico

    OpenAIRE

    JULIO PÉREZ; MANUEL CABARCAS; LINA VELILLA; IVAN URIBE; CUSTODIO VASQUEZ

    2008-01-01

    La integridad de los equipos en la Industria Petrolera, es de gran importancia por razones de seguridad, cumplimiento con regulaciones ambientales, reducción de costos de mantenimiento y prevención de paros inesperados de producción. El objetivo de este artículo es establecer una metodología para evaluar la integridad de pozos que utilicen el Calentamiento Eléctrico como método de recobro mejorado, de tal manera que se pueda definir si los pozos en estudio se encuentran en condiciones mecánic...

  7. Optimization of axial enrichment distribution for BWR fuels using scoping libraries and block coordinate descent method

    Energy Technology Data Exchange (ETDEWEB)

    Tung, Wu-Hsiung, E-mail: wstong@iner.gov.tw; Lee, Tien-Tso; Kuo, Weng-Sheng; Yaur, Shung-Jung

    2017-03-15

    Highlights: • An optimization method for axial enrichment distribution in a BWR fuel was developed. • Block coordinate descent method is employed to search for optimal solution. • Scoping libraries are used to reduce computational effort. • Optimization search space consists of enrichment difference parameters. • Capability of the method to find optimal solution is demonstrated. - Abstract: An optimization method has been developed to search for the optimal axial enrichment distribution in a fuel assembly for a boiling water reactor core. The optimization method features: (1) employing the block coordinate descent method to find the optimal solution in the space of enrichment difference parameters, (2) using scoping libraries to reduce the amount of CASMO-4 calculation, and (3) integrating a core critical constraint into the objective function that is used to quantify the quality of an axial enrichment design. The objective function consists of the weighted sum of core parameters such as shutdown margin and critical power ratio. The core parameters are evaluated by using SIMULATE-3, and the cross section data required for the SIMULATE-3 calculation are generated by using CASMO-4 and scoping libraries. The application of the method to a 4-segment fuel design (with the highest allowable segment enrichment relaxed to 5%) demonstrated that the method can obtain an axial enrichment design with improved thermal limit ratios and objective function value while satisfying the core design constraints and core critical requirement through the use of an objective function. The use of scoping libraries effectively reduced the number of CASMO-4 calculation, from 85 to 24, in the 4-segment optimization case. An exhausted search was performed to examine the capability of the method in finding the optimal solution for a 4-segment fuel design. The results show that the method found a solution very close to the optimum obtained by the exhausted search. The number of

  8. Digital implementation, simulation and tests in MATLAB of the models of Steam line, the turbines, the pressure regulator of a BWR type nucleo electric power plant; Implementacion digital, simulacion y pruebas en MATLAB de los modelos de la linea de vapor, las turbinas y el regulador de presion de una central Nucleoelectrica tipo BWR

    Energy Technology Data Exchange (ETDEWEB)

    Lopez R, A. [UNAM, Laboratorio de Analisis de Ingenieria de Reactores Nucleares, DEPFI, Campus Morelos, en IMTA Jiutepec, Morelos (Mexico)]. e-mail: andyskamx@yahoo.com.mx

    2004-07-01

    In this phase of the project they were carried out exhaustive tests to the models of the steam lines, turbines and pressure regulator of a BWR type nucleo electric central for to verify that their tendencies and behaviors are it more real possible. For it, it was necessary to also analyze the transfer functions of the different components along the steam line until the power generator. Such models define alone the dominant poles of the system, what is not limitation to reproduce a wide range of anticipated transitoriness of a power station operation. In the same manner, it was integrated and proved the integrated model form with the models of feeding water of the SUN-RAH, simulating the nuclear reactor starting from predetermined entrances of the prospective values of the vessel. Also it was coupled with the graphic interface developed with the libraries DirectX implementing a specific monitoring panel for this system. (Author)

  9. THERMAL EVALUATION OF THE USE OF BWR MOX SNF IN THE WASTE PACKAGE DESIGN (SCPB: N/A)

    Energy Technology Data Exchange (ETDEWEB)

    H. Wang

    1997-01-23

    This analysis is prepared by the Mined Geologic Disposal System (MGDS) Waste Package Development Department (WPDD) as specified in the Waste Package Implementation Plan (pp. 4-8,4-11,4-24, 5-1, and 5-13; Ref. 5.10) and Waste Package Plan (pp. 3-15,3-17, and 3-24; Ref. 5.9). The design data request addressed herein is: (1) Characterize the conceptual 40 BWR and 24 BWR Multi-Purpose Canister (MPC) Waste Package (WP) design to show that the design is feasible for use in the MGDS environment when loaded with BWR MOX SNF. (2) Characterize the conceptual 44 BWR and 24 BWR Uncanistered Fuel (UCF) Waste Package (WP) design to show that the design is feasible for use in the MGDS environment when loaded with BWR MOX SNF. The purpose of this analysis is to respond to a concern that the long-term disposal thermal issues for the WP Design, if used with SNF designed for a MOX fuel cycle, do not preclude WP compatibility with the MGDS. The objective of this analysis is to provide thermal parameter information for the conceptual WP design with disposal container which is loaded with BWR MOX SNF under nominal MGDS repository conditions. The results are intended to show that the design has a reasonable chance to meet the MGDS design requirements for normal MGDS operation, and to provide the required guidance to determining the major design issues for future design efforts, and to show that the BWR MOX SNF loaded WP performance is similar to an WP loaded with commercial BWR SNF.

  10. Comparison study of the thermal mechanical performance of fuel rods during BWR fuel preconditioning operations using the computer codes FUELSIM and FEMAXI-V

    Energy Technology Data Exchange (ETDEWEB)

    Pantoja C, R. [IPN, Escuela Superior de Fisica y Matematicas, Departamento de Ingenieria Nuclear, Av. Instituto Politecnico Nacional s/n, Col. San Pedro Zacatenco, 07738 Mexico D. F. (Mexico); Ortiz V, J.; Castillo D, R., E-mail: rafael.pantoja10@yahoo.com.m [ININ, Departamento de Sistemas Nucleares, Carretera Mexico-Toluca s/n, Ocoyoacac 52750, Estado de Mexico (Mexico)

    2010-10-15

    The safety of nuclear power plants requires monitoring those parameters having some direct or indirect effect on safety. The thermal limits are values set for those parameters considered having most impact on the safe operation of a nuclear power reactor. Some thermal limits monitoring requires the thermal-mechanical analysis of the rods containing the nuclear fuel. The fuel rod thermal-mechanical behaviour under irradiation is a complex process in which there exists a great deal of interrelated physical and chemical phenomena, so that the fuel rod performance analysis in the core of a nuclear power reactor is generally accomplished by using computer codes, which integrate several of the phenomena that are expected to occur during the lifetime of the fuel rod in the core. In the operation of a nuclear power reactor, pre-conditioning simulations are necessary to determine in advance limit values for the power that can be generated in a fuel rod during any power ramp, and mainly during reactor startup, and thus avoiding any rod damage. In this work, a first analysis of the thermal-mechanical performance of typical fuel rods used in nuclear reactors of the type BWR is performed. This study includes two types of fuel rods: one from a fuel assembly design with array 8 x 8, and the other one from a 10 x 10 fuel assembly design, and a comparison of the thermal-mechanical performance between the two different rod designs is performed. The performance simulations were performed by the code FUELSIM, and compared against results previously obtained from similar simulation with the code FEMAXI-V. (Author)

  11. Signal analysis of acoustic and flow-induced vibrations of BWR main steam line

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa-Paredes, G., E-mail: gepe@xanum.uam.mx [División de Ciencias Básicas e Ingeniería, Universidad Autónoma Metropolitana-Iztapalapa, México, D.F. 09340 (Mexico); Prieto-Guerrero, A. [División de Ciencias Básicas e Ingeniería, Universidad Autónoma Metropolitana-Iztapalapa, México, D.F. 09340 (Mexico); Núñez-Carrera, A. [Comisión Nacional de Seguridad Nuclear y Salvaguardias, Doctor Barragán 779, Col. Narvarte, México, D.F. 03020 (Mexico); Vázquez-Rodríguez, A. [División de Ciencias Básicas e Ingeniería, Universidad Autónoma Metropolitana-Iztapalapa, México, D.F. 09340 (Mexico); Centeno-Pérez, J. [Instituto Politécnico Nacional, Escuela Superior de Física y Matemáticas Unidad Profesional “Adolfo López Mateos”, Av. IPN, s/n, México, D.F. 07738 (Mexico); Espinosa-Martínez, E.-G. [Departamento de Sistemas Energéticos, Universidad Nacional Autónoma de México, México, D.F. 04510 (Mexico); and others

    2016-05-15

    Highlights: • Acoustic and flow-induced vibrations of BWR are analyzed. • BWR performance after extended power uprate is considered. • Effect of acoustic side branches (ASB) is analyzed. • The ASB represents a reduction in the acoustic loads to the steam dryer. • Methodology developed for simultaneous analyzing the signals in the MSL. - Abstract: The aim of this work is the signal analysis of acoustic waves due to phenomenon known as singing in Safety Relief Valves (SRV) of the main steam lines (MSL) in a typical BWR5. The acoustic resonance in SRV standpipes and fluctuating pressure is propagated from SRV to the dryer through the MSL. The signals are analyzed with a novel method based on the Multivariate Empirical Mode Decomposition (M-EMD). The M-EMD algorithm has the potential to find common oscillatory modes (IMF) within multivariate data. Based on this fact, we implement the M-EMD technique to find the oscillatory mode in BWR considering the measurements obtained collected by the strain gauges located around the MSL. These IMF, analyzed simultaneously in time, allow obtaining an estimation of the effects of the multiple-SRV in the MSL. Two scenarios are analyzed: the first is the signal obtained before the installation of the acoustic dampers (ASB), and the second, the signal obtained after installation. The results show the effectiveness of the ASB to damp the strong resonances when the steam flow increases, which represents an important reduction in the acoustic loads to the steam dryer.

  12. Reactor Physics

    Energy Technology Data Exchange (ETDEWEB)

    Ait Abderrahim, A

    2001-04-01

    The Reactor Physics and MYRRHA Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis of reactor fuel. This expertise is applied in the Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments by means of neutron and gamma calculations. The activities of the Fuzzy Logic and Intelligent Technologies in Nuclear Science programme cover several domains outside the department. Progress and achievements in these topical areas in 2000 are summarised.

  13. Performance of iron–chromium–aluminum alloy surface coatings on Zircaloy 2 under high-temperature steam and normal BWR operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Zhong, Weicheng; Mouche, Peter A.; Han, Xiaochun [University of Illinois, Department of Nuclear, Radiological, and Plasma Engineering, Urbana, IL 61801 (United States); Heuser, Brent J., E-mail: bheuser@illinois.edu [University of Illinois, Department of Nuclear, Radiological, and Plasma Engineering, Urbana, IL 61801 (United States); Mandapaka, Kiran K.; Was, Gary S. [University of Michigan, Department of Nuclear Engineering and Radiological Sciences, Ann Arbor, MI 48109 (United States)

    2016-03-15

    Iron-chromium-aluminum (FeCrAl) coatings deposited on Zircaloy 2 (Zy2) and yttria-stabilized zirconia (YSZ) by magnetron sputtering have been tested with respect to oxidation weight gain in high-temperature steam. In addition, autoclave testing of FeCrAl-coated Zy2 coupons under pressure-temperature-dissolved oxygen coolant conditions representative of a boiling water reactor (BWR) environment has been performed. Four different FeCrAl compositions have been tested in 700 °C steam; compositions that promote alumina formation inhibited oxidation of the underlying Zy2. Parabolic growth kinetics of alumina on FeCrAl-coated Zy2 is quantified via elemental depth profiling. Autoclave testing under normal BWR operating conditions (288 °C, 9.5 MPa with normal water chemistry) up to 20 days demonstrates observable weight gain over uncoated Zy2 simultaneously exposed to the same environment. However, no FeCrAl film degradation was observed. The 900 °C eutectic in binary Fe–Zr is addressed with the FeCrAl-YSZ system. - Graphical abstract: Weight gain normalized to total sample surface area versus time during 700 °C steam exposure for FeCrAl samples with different composition (A) and Fe/Cr/Al:62/4/34 (B). In both cases, the responses of uncoated Zry2 (Zry2-13A and Zry2-19A) are shown for comparison. This uncoated Zry2 response shows the expected pre-transition quasi-cubic kinetic behavior and eventual breakaway (linear) kinetics. Highlights: • FeCrAl coatings deposited on Zy2 have been tested with respect to oxidation in high-temperature steam. • FeCrAl compositions promoting alumina formation inhibited oxidation of Zy2 and delay weight gain. • Autoclave testing to 20 days of coated Zy2 in a simulated BWR environment demonstrates minimal weight gain and no film degradation. • The 900 °C eutectic in binary Fe-Zr is addressed with the FeCrAl-YSZ system.

  14. Parametric and experimentally informed BWR Severe Accident Analysis Utilizing FeCrAl - M3FT-17OR020205041

    Energy Technology Data Exchange (ETDEWEB)

    Ott, Larry J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Howell, Michael [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Robb, Kevin R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-08-01

    Iron-chromium-aluminum (FeCrAl) alloys are being considered as advanced fuel cladding concepts with enhanced accident tolerance. At high temperatures, FeCrAl alloys have slower oxidation kinetics and higher strength compared with zirconium-based alloys. FeCrAl could be used for fuel cladding and spacer or mixing vane grids in light water reactors and/or as channel box material in boiling water reactors (BWRs). There is a need to assess the potential gains afforded by the FeCrAl accident-tolerant-fuel (ATF) concept over the existing zirconium-based materials employed today. To accurately assess the response of FeCrAl alloys under severe accident conditions, a number of FeCrAl properties and characteristics are required. These include thermophysical properties as well as burst characteristics, oxidation kinetics, possible eutectic interactions, and failure temperatures. These properties can vary among different FeCrAl alloys. Oak Ridge National Laboratory has pursued refined values for the oxidation kinetics of the B136Y FeCrAl alloy (Fe-13Cr-6Al wt %). This investigation included oxidation tests with varying heating rates and end-point temperatures in a steam environment. The rate constant for the low-temperature oxidation kinetics was found to be higher than that for the commercial APMT FeCrAl alloy (Fe-21Cr-5Al-3Mo wt %). Compared with APMT, a 5 times higher rate constant best predicted the entire dataset (root mean square deviation). Based on tests following heating rates comparable with those the cladding would experience during a station blackout, the transition to higher oxidation kinetics occurs at approximately 1,500°C. A parametric study varying the low-temperature FeCrAl oxidation kinetics was conducted for a BWR plant using FeCrAl fuel cladding and channel boxes using the MELCOR code. A range of station blackout severe accident scenarios were simulated for a BWR/4 reactor with Mark I containment. Increasing the FeCrAl low-temperature oxidation rate

  15. Axial profiles of burned and fraction of holes for calculations of criticality with credit for BWR fuel burning; Perfiles axiales de quemado y fraccion de huecos para calculos de criticidad con credito al quemado para combustible BWR

    Energy Technology Data Exchange (ETDEWEB)

    Casado Sanchez, C.; Rubio Oviedo, P.

    2014-07-01

    This paper presents a method to define surround profiles of burning and fraction of holes suited for use in applications of credit to burning of BWR fuel from results obtained with the module STARBUCS of SCALE. (Author)

  16. Reactor safeguards

    CERN Document Server

    Russell, Charles R

    1962-01-01

    Reactor Safeguards provides information for all who are interested in the subject of reactor safeguards. Much of the material is descriptive although some sections are written for the engineer or physicist directly concerned with hazards analysis or site selection problems. The book opens with an introductory chapter on radiation hazards, the construction of nuclear reactors, safety issues, and the operation of nuclear reactors. This is followed by separate chapters that discuss radioactive materials, reactor kinetics, control and safety systems, containment, safety features for water reactor

  17. Reactor operation

    CERN Document Server

    Shaw, J

    2013-01-01

    Reactor Operation covers the theoretical aspects and design information of nuclear reactors. This book is composed of nine chapters that also consider their control, calibration, and experimentation.The opening chapters present the general problems of reactor operation and the principles of reactor control and operation. The succeeding chapters deal with the instrumentation, start-up, pre-commissioning, and physical experiments of nuclear reactors. The remaining chapters are devoted to the control rod calibrations and temperature coefficient measurements in the reactor. These chapters also exp

  18. Las reformas constitucionales provinciales deben preservar el derecho a la dignidad de la persona humana en su integridad psicofísica

    National Research Council Canada - National Science Library

    Robledo, Federico Justiniano

    2008-01-01

    ... en la órbita provincial, con particular referencia a los límites del Poder Constituyente. Se sostiene que el Poder Constituyente provincial debe preservar los derechos derivados de la dignidad de la persona humana en su integridad psicofísica...

  19. Derechos de la personalidad y derechos fundamentales, derecho a la vida e integridad física, derecho a la libertad, honor, intimidad e imagen

    OpenAIRE

    Heras García, Manuel Ángel de las

    2017-01-01

    Estudio de los derechos o bienes de la personalidad y su regulación como derechos fundamentales en la Constitución. Análisis de los derechos a la vida, integridad física, libertad, honor, intimidad e imagen. Jurisprudencia.

  20. Design of a boiling water reactor core based on an integrated blanket-seed thorium-uranium concept

    Energy Technology Data Exchange (ETDEWEB)

    Nunez-Carrera, Alejandro [Facultad de Ingenieria, Universidad Nacional Autonoma de Mexico, Laboratorio de Analisis en Ingenieria de Reactores Nucleares, Paseo Cuauhnahuac 8532, 62550 Jiutepec, Mor. (Mexico); Comision Nacional de Seguridad Nuclear y Salvaguardias, Dr. Barragan 779, Col. Narvarte, 03020 Mexico, D.F. (Mexico); Francois, Juan Luis [Facultad de Ingenieria, Universidad Nacional Autonoma de Mexico, Laboratorio de Analisis en Ingenieria de Reactores Nucleares, Paseo Cuauhnahuac 8532, 62550 Jiutepec, Mor. (Mexico)]. E-mail: jlfl@fi-b.unam.mx; Martin-del-Campo, Cecilia [Facultad de Ingenieria, Universidad Nacional Autonoma de Mexico, Laboratorio de Analisis en Ingenieria de Reactores Nucleares, Paseo Cuauhnahuac 8532, 62550 Jiutepec, Mor. (Mexico); Espinosa-Paredes, Gilberto [Area de Ingenieria en Recursos Energeticos, Universidad Autonoma Metropolitana, Avenida San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico, D.F. (Mexico)

    2005-04-15

    This paper is concerned with the design of a boiling water reactor (BWR) equilibrium core using thorium as a nuclear material in an integrated blanket-seed (BS) assembly. The integrated BS concept comes from the fact that the blanket and the seed rods are located in the same assembly, and are burned out in a once-through cycle. The idea behind the lattice design is to use the thorium conversion capability in a BWR spectrum, taking advantage of the {sup 233}U build-up. A core design was developed to achieve an equilibrium cycle of 365 effective full power days in a standard BWR with a reload of 104 fuel assemblies designed with an average {sup 235}U enrichment of 7.5 w/o in the seed sub-lattice. The main operating parameters, like power, linear heat generation rate and void distributions were obtained as well as the shutdown margin. It was observed that the analyzed parameters behave like those obtained in a standard BWR. The shutdown margin design criterion was fulfilled by addition of a burnable poison region in the fuel assembly.

  1. Research Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Martens, Frederick H. [Argonne National Laboratory; Jacobson, Norman H.

    1968-09-01

    This booklet discusses research reactors - reactors designed to provide a source of neutrons and/or gamma radiation for research, or to aid in the investigation of the effects of radiation on any type of material.

  2. Simulation of the Lower Head Boiling Water Reactor Vessel in a Severe Accident

    Directory of Open Access Journals (Sweden)

    Alejandro Nuñez-Carrera

    2012-01-01

    Full Text Available The objective of this paper is the simulation and analysis of the BoilingWater Reactor (BWR lower head during a severe accident. The COUPLE computer code was used in this work to model the heatup of the reactor core material that slumps in the lower head of the reactor pressure vessel. The prediction of the lower head failure is an important issue in the severe accidents field, due to the accident progression and the radiological consequences that are completely different with or without the failure of the Reactor Pressure Vessel (RPV. The release of molten material to the primary containment and the possibility of steam explosion may produce the failure of the primary containment with high radiological consequences. Then, it is important to have a detailed model in order to predict the behavior of the reactor vessel lower head in a severe accident. In this paper, a hypothetical simulation of a Loss of Coolant Accident (LOCA with simultaneous loss of off-site power and without injection of cooling water is presented with the proposal to evaluate the temperature distribution and heatup of the lower part of the RPV. The SCDAPSIM/RELAP5 3.2 code was used to build the BWR model and conduct the numerical simulation.

  3. Selection of nuclear reactors through the hierarchic analysis process: the Mexican case; Seleccion de reactores nucleares mediante el proceso de analisis jerarquico: el caso Mexicano

    Energy Technology Data Exchange (ETDEWEB)

    Martin del Campo, C.; Nelson, P.F.; Francois, J.L. [Departamento de Sistemas Energeticos, Facultad de Ingenieria, UNAM, Paseo Cuauhnahuac 8532, Jiutepec, 62550 Morelos (Mexico)]. e-mail: cmcm@fi-b.unam.mx

    2008-07-01

    In this work the decision making method known as hierarchical analysis process for the selection of a new reactor in Mexico was applied. The main objective of the process it is to select the nuclear reactor technology more appropriate for Mexico, to begin the bid process inside one or two years to begin their operation in 2016. The options were restricted to four reactors that fulfill the following ones approaches: 1) its are advanced reactors, from the technological point of view, with regard to the reactors that at the moment operate in the Laguna Verde Power Station, 2) its are reactors that have the totally finished design, 3) its are reactors that already have the certification on the part of the regulator organism of the origin country or that they are in an advanced state of the certification process and 4) its are reactors offered by the companies that they have designed and built the greater number of reactors that are at the moment in operation at world level. Taking into account these restrictions it was decided to consider as alternative at the reactors: Advanced Boiling Water Reactor (A BWR), European Reactor of Pressurized Water (EPR), Water at Pressure reactor (AP1000) and Simplified Economic Reactor of Boiling Water (ESBWR). The evaluation approaches include economic and of safety indicators, qualitative some of them and other quantitative ones. Another grade of complexity in the solution of the problem is that there are actors that can be involved in the definition of the evaluation approaches and in the definition of the relative importance among them, according to each actor's interests. To simplify the problem its were only considered two actors or groups of interest that can influence in more significant way and that are the Federal Commission of Electricity and the National Commission of Nuclear Safety and Safeguards. The qualifications for each reactor in function of the evaluation approaches were obtained, being the A BWR the best

  4. Validation of the Monte Carlo model developed to estimate doses around the irradiated fuel pool produced by activated control rods discharged from a BWR

    Energy Technology Data Exchange (ETDEWEB)

    Abarca, Agustin; Gallardo, Sergio; Rodenas, Jose [Universidad Politecnica de Valencia (Spain). Dept. de Ingenieria Quimica y Nuclear], e-mail: ergalbe@iqn.upv.es

    2009-07-01

    BWR control rods are irradiated into the reactor by the neutron flux and consequently materials composing the rod become activated. When the control rods are withdrawn from the reactor, they must be stored into the spent fuel storage pool of the plant at a certain depth under water. Doses potentially received by plant workers in the area surrounding the pool edges as well as in a platform moving over the water surface should be calculated to assure the adequate protection. Irradiated fuel elements are stored at the bottom of the pool while controls rods are nearer the surface. Therefore, doses out of the pool are mainly produced by activated control rods. The MCNP5 code based on the Monte Carlo method has been applied to model the pool containing hanger devices with irradiated control rods and to estimate dose rates at points of interest. To obtain dose rates on the pool and around it an F4MESH tally has been used. Furthermore, the SSW/SSR technique has been applied in order to strongly reduce the computer time. Results have been compared with measurements in plant in order to validate the model. An interesting application of the validated model is the assessment of doses when some variation is introduced in the distribution of activated material. (author)

  5. Study of environmental noise in a BWR plant like the Nuclear Power Plant Laguna Verde; Estudio de ruido ambiental en una planta BWR como la Central Nuclear Laguna Verde

    Energy Technology Data Exchange (ETDEWEB)

    Tijerina S, F.; Cruz G, M.; Amador C, C., E-mail: francisco.tijerina@cfe.gob.mx [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Subgerencia de Ingenieria, Carretera Cardel-Nautla Km. 42.5, Alto Lucero, Veracruz (Mexico)

    2013-10-15

    In all industry type the health costs generated by the noise are high, because the noise can cause nuisance and to harm the capacity to work when causing tension and to perturb the concentration, and in more severe cases to reach to lose the sense of the hearing in the long term. The noise levels in the industry have been designated for the different types of use like residential, commercial, and industrial and silence areas. The noise can cause accidents when obstructing the communications and alarm signs. For this reason the noise should be controlled and mitigated, at a low level as reasonably is possible, taking into account that the noise is an acoustic contamination. The present study determines a bases line of the environmental noise levels in a nuclear power plant BWR-5 as Laguna Verde, (like reference) to be able to determine and to give pursuit to the possible solutions to eliminate or to limit the noise level in the different job areas. The noise levels were registered with a meter of integrative noise level (sonometer) and areas of noise exposure levels mapping the general areas in the buildings were established, being the registered maximum level of 96.94 dba in the building of the Reactor-elevation 0.65 m under the operation conditions of Extended Power Up rate (EPU) of 120% PTN. Knowing that the exposition to noises and the noise dose in the job place can influence in the health and in the safety of the workers, are extensive topics that they should be analyzed for separate as they are: to) the effects in the health of the exposure to the noise, b) how measuring the noise, c) the methods and technologies to combat and to control the noise in the industry by part of engineering area and d) the function of the industrial safety bodies as delegates of the health and safety in the task against the noise in the job. (author)

  6. CONVECTION REACTOR

    Science.gov (United States)

    Hammond, R.P.; King, L.D.P.

    1960-03-22

    An homogeneous nuclear power reactor utilizing convection circulation of the liquid fuel is proposed. The reactor has an internal heat exchanger looated in the same pressure vessel as the critical assembly, thereby eliminating necessity for handling the hot liquid fuel outside the reactor pressure vessel during normal operation. The liquid fuel used in this reactor eliminates the necessity for extensive radiolytic gas rocombination apparatus, and the reactor is resiliently pressurized and, without any movable mechanical apparatus, automatically regulates itself to the condition of criticality during moderate variations in temperature snd pressure and shuts itself down as the pressure exceeds a predetermined safe operating value.

  7. Calculation system for physical analysis of boiling water reactors; Modelisation des phenomenes physiques specifiques aux reacteurs a eau bouillante, notamment le couplage neutronique-thermohydraulique

    Energy Technology Data Exchange (ETDEWEB)

    Bouveret, F

    2001-07-01

    Although Boiling Water Reactors generate a quarter of worldwide nuclear electricity, they have been only little studied in France. A certain interest now shows up for these reactors. So, the aim of the work presented here is to contribute to determine a core calculation methodology with CEA (Commissariat a l'Energie Atomique) codes. Vapour production in the reactor core involves great differences in technological options from pressurised water reactor. We analyse main physical phenomena for BWR and offer solutions taking them into account. BWR fuel assembly heterogeneity causes steep thermal flux gradients. The two dimensional collision probability method with exact boundary conditions makes possible to calculate accurately the flux in BWR fuel assemblies using the APOLLO-2 lattice code but induces a very long calculation time. So, we determine a new methodology based on a two-level flux calculation. Void fraction variations in assemblies involve big spectrum changes that we have to consider in core calculation. We suggest to use a void history parameter to generate cross-sections libraries for core calculation. The core calculation code has also to calculate the depletion of main isotopes concentrations. A core calculation associating neutronics and thermal-hydraulic codes lays stress on points we still have to study out. The most important of them is to take into account the control blade in the different calculation stages. (author)

  8. Stress analyses for reactor pressure vessels by the example of a product line '69 boiling water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Mkrtchyan, Lilit; Schau, Henry [TUEV SUED Energietechnik GmbH, Mannheim (Germany). Abt. Strukturverhalten; Wolf, Werner; Holzer, Wieland [TUEV SUED Industrie Service GmbH, Muenchen (Germany). Abt. Behaelter und Turbosatz; Wernicke, Robert; Trieglaff, Ralf [TUEV NORD SysTec GmbH und Co. KG, Hamburg (Germany). Abt. Festigkeit und Konstruktion

    2011-08-15

    The reactor pressure vessels (RPV) of boiling water reactors (BWR) belonging to the product line '69 have unusually designed heads. The spherical cap-shaped bottom head of the vessel is welded directly to the support flange of the lower shell course. This unusual construction has led repeatedly to controversial discussions concerning the limits and admissibility of stress intensities arising in the junction of the bottom head to the cylindrical shell. In the present paper, stress analyses for the design conditions are performed with the finite element method in order to determine and categorize the occurring stresses. The procedure of stress classification in accordance with the guidelines of German KTA 3201.2 and Section III of the ASME Code (Subsection NB) is described and subsequently demonstrated by the example of a typical BWR vessel. The accomplished investigations yield allowable stress intensities in the considered area. Additionally, limit load analyses are carried out to verify the obtained results. Complementary studies, performed for a torispherical head, prove that the determined maximum peak stresses in the junction between the bottom head and the cylindrical shell are not unusual also for pressure vessels with regular bottom head constructions. (orig.)

  9. Evaluation of the reduction of boron-10 in the control rods in the BWR of the Laguna Verde Central, through steady state calculations; Evaluacion de la reduccion del Boro-10 en las barras de control en los BWR de la CLV, mediante calculos en estado estacionario

    Energy Technology Data Exchange (ETDEWEB)

    Montes T, J.L.; Perusquia, R.; Hernandez, J.L.; Ramirez S, J.R. [Departamento de Sistemas Nucleares, ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2003-07-01

    One of the more important aspects related with the safety and economy in the operation of a nuclear power reactor, it is without a doubt the control of the reactivity. During the normal operation of a reactor of boiling water (BWR-Boiling Water Reactor), the control of the reactivity in the nucleus it is strongly determined by the efficiency of the control rods. In the case of the Laguna Verde Nuclear power station (CNLV) the nucleus of the reactors has 109 control rods grouped in 4 sets. The CNLV at the moment uses the CCC method (Control Cell Core) in the design of the cycle. With this method only the A2 group is used for the control of the reactivity at full power. With the purpose of quantifying the effect of the decrease of the burnable poison (B{sub 4}C) of the control rods and in particular to the effect due to the postulated lost of 10% of Boron 10, it was carried out a series of calculations of the nucleus in stationary state by means of the system of HELIOS/CM-PRESTO codes. In this work the main derived results of these 3D simulations(three dimensions) of the reactors of the CNLV are presented. It was analyzed the one behavior of the infinite neutron multiplication factor (K{sub infinite}), at fuel assemble cell level used in an equilibrium cycle for the CNLV. It was also analyzed the effect in the shutdown margin (ShutDown Margin- SDM) in cold condition CZP (Cold Zero Power). Its are also included those results of the ARI cases (All Rods In) and SRO (Strong Rod Out). From the cases in condition HFP (Hot Full Power) the behavior of the effective multiplication factor (K{sub eff}) is presented. (Author)

  10. Modelling of the dynamics of the vessel and circuits of recirculation of a BWR type nucleo electric as part of the SUN-RAH university simulator; Modelado de la dinamica de la vasija y circuitos de recirculacion de una nucleoelectrica tipo BWR como parte del simulador universitario SUN-RAH

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez S, R.A. [DEPFI, Campus Morelos, en IMTA, Jiutepec, Morelos (Mexico)]. e-mail: rsanchez_15@yahoo.com.mx

    2003-07-01

    In the present project, the development of a model for the dynamics of the process of energy transport generated in the nuclear fuel until the main steam lines of a nucleo electric central with BWR type nuclear reactor, using mathematical models of reduced order is presented. These models present the main characteristics of the reactor vessel and of the recirculation system, defined by the main phenomena that intervene in those physical processes. Likewise, the objective of the general project of the one University student nucleo electric simulator with Boiling Water Reactor (SUN-RAH) for later on to establish the modeling equations for each part of the nuclear reactor as well as of the load pursuit system. Also, its were described the graphic interfaces implemented in an three layers architecture in which the different measuring variables are presented in the monitor. It fits signalize that the advantage presented by the University student nucleo electric simulator is the possibility to carry out changes in the magnitudes of those different variables that intervene in the physical processes made in the one reactor and in the recirculation system in execution time of the same one. Of same way, the creation of a graphic intuitive interface, friendly, and designed with the same technology with the one that the video games are programmed in the present time. Besides all the above mentioned, the pending goals inside of the project are exposed, as well as the developments in construction process or conceptualized to be included in future versions of the simulator. Finally its are thinking about possible scenarios of applications of SUN-RAH, as well as their reaches. (Author)

  11. BWR Spent Nuclear Fuel Interfacial Bonding Efficiency Study

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jy-An John [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jiang, Hao [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-04-30

    The objective of this project is to perform a systematic study of spent nuclear fuel (SNF, also known as “used nuclear fuel” [UNF]) integrity under simulated transportation environments using the Cyclic Integrated Reversible-Bending Fatigue Tester (CIRFT) hot-cell testing technology developed at Oak Ridge National Laboratory (ORNL) in August 2013. Under Nuclear Regulatory Commission (NRC) sponsorship, ORNL completed four benchmark tests, four static tests, and twelve dynamic or cycle tests on H. B. Robinson (HBR) high burn-up (HBU) fuel. The clad of the HBR fuels was made of Zircaloy-4. Testing was continued in fiscal year (FY) 2014 using Department of Energy (DOE) funds. Additional CIRFT testing was conducted on three HBR rods; two specimens failed, and one specimen was tested to over 2.23 × 107 cycles without failing. The data analysis on all the HBR SNF rods demonstrated that it is necessary to characterize the fatigue life of the SNF rods in terms of (1) the curvature amplitude and (2) the maximum absolute of curvature extremes. The maximum extremes are significant because they signify the maximum tensile stress for the outer fiber of the bending rod. CIRFT testing has also addressed a large variation in hydrogen content on the HBR rods. While the load amplitude is the dominant factor that controls the fatigue life of bending rods, the hydrogen content also has an important effect on the lifetime attained at each load range tested. In FY 15, eleven SNF rod segments from the Limerick BWR were tested using the ORNL CIRFT equipment; one test under static conditions and ten tests under dynamic loading conditions. Under static unidirectional loading, a moment of 85 N·m was obtained at a maximum curvature of 4.0 m-1. The specimen did not show any sign of failure during three repeated loading cycles to a similar maximum curvature. Ten cyclic tests were conducted with amplitudes varying from 15.2 to 7.1 N·m. Failure was observed in nine of

  12. Analysis of results of AZTRAN and AZKIND codes for a BWR; Analisis de resultados de los codigos AZTRAN y AZKIND para un BWR

    Energy Technology Data Exchange (ETDEWEB)

    Bastida O, G. E.; Vallejo Q, J. A.; Galicia A, J.; Francois L, J. L. [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Paseo Cuauhnahuac 8532, 62550 Jiutepec, Morelos (Mexico); Xolocostli M, J. V.; Rodriguez H, A.; Gomez T, A. M., E-mail: gbo729@yahoo.com.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2016-09-15

    This paper presents an analysis of results obtained from simulations performed with the neutron transport code AZTRAN and the kinetic code of neutron diffusion AZKIND, based on comparisons with models corresponding to a typical BWR, in order to verify the behavior and reliability of the values obtained with said code for its current development. For this, simulations of different geometries were made using validated nuclear codes, such as CASMO, MCNP5 and Serpent. The results obtained are considered adequate since they are comparable with those obtained and reported with other codes, based mainly on the neutron multiplication factor and the power distribution of the same. (Author)

  13. Power reactor noise studies and applications

    Energy Technology Data Exchange (ETDEWEB)

    Arzhanov, V

    2002-03-01

    The present thesis deals with the neutron noise arising in power reactor systems. Generally, it can be divided into two major parts: first, neutron noise diagnostics, or more specifically, novel methods and algorithms to monitor nuclear industrial reactors; and second, contributions to neutron noise theory as applied to power reactor systems. Neutron noise diagnostics is presented by two topics. The first one is a theoretical study on the possibility to use a newly proposed current-flux (C/F) detector in Pressurised Water Reactors (PWR) for the localisation of anomalies. The second topic concerns various methods to detect guide tube impacting in Boiling Water Reactors (BWR). The significance of these problems comes from the operational experience. The thesis describes a novel method to localise vibrating control rods in a PWR by using only one C/F detector. Another novel method, based on wavelet analysis, is put forward to detect impacting guide tubes in a BWR. Neutron noise theory is developed for both Accelerator Driven Systems (ADS) and traditional reactors. By design the accelerator-driven systems would operate in a subcritical mode with a strong external source. This calls for a revision of many concepts and methods that have been developed for traditional reactors and also it poses a number of new problems. As for the latter, the thesis investigates the space-dependent neutron noise caused by a fluctuating source. It is shown that the frequency-dependent spatial behaviour exhibits some new properties that are different from those known in traditional critical systems. On the other hand, various reactor physics approximations (point kinetic, adiabatic etc.) have not been defined yet for the subcritical systems. In this respect the thesis presents a systematic formulation of the above mentioned approximations as well as investigations of their properties. Another important problem in neutron noise theory is the treatment of moving boundaries. In this case one

  14. Development of a scatter search optimization algorithm for BWR fuel lattice design

    Energy Technology Data Exchange (ETDEWEB)

    Francois, J.L.; Martin-del-Campo, C. [Mexico Univ. Nacional Autonoma, Facultad de Ingenieria (Mexico); Morales, L.B.; Palomera, M.A. [Mexico Univ. Nacional Autonoma, Instituto de Investigaciones en Matematicas Aplicadas y Sistemas, D.F. (Mexico)

    2005-07-01

    A basic Scatter Search (SS) method, applied to the optimization of radial enrichment and gadolinia distributions for BWR fuel lattices, is presented in this paper. Scatter search is considered as an evolutionary algorithm that constructs solutions by combining others. The goal of this methodology is to enable the implementation of solution procedures that can derive new solutions from combined elements. The main mechanism for combining solutions is such that a new solution is created from the strategic combination of two other solutions to explore the solutions' space. Results show that the Scatter Search method is an efficient optimization algorithm applied to the BWR design and optimization problem. Its main features are based on the use of heuristic rules since the beginning of the process, which allows directing the optimization process to the solution, and to use the diversity mechanism in the combination operator, which allows covering the search space in an efficient way. (authors)

  15. Development of membrane moisture separator for BWR off-gas system

    Energy Technology Data Exchange (ETDEWEB)

    Ogata, H.; Kawamura, S. [Tokyo Electric Power Co., Inc. (Japan); Kumasaka, M. [Hitachi Ltd., Ibaraki (Japan); Nishikubo, M. [Toshiba Corp., Yokohama (Japan)

    2001-07-01

    In BWR plant off-gas treatment systems, dehumidifiers are used to maintain noble gas adsorption efficiency in the first half of the charcoal hold-up units. From the perspective of simplifying and reducing the cost of such a dehumidification system, Japanese BWR utilities and plant fabricators have been developing a dehumidification system employing moisture separation membrane of the type already proven in fields such as medical instrumentation and precision measuring apparatus. The first part of this development involved laboratory testing to simulate the conditions found in an actual off-gas system, the results of which demonstrated satisfactory results in terms of moisture separation capability and membrane durability, and suggested favorable prospects for application in actual off-gas systems. Further, in-plant testing to verify moisture separation capability and membrane durability in the presence of actual gases is currently underway, with results so far suggesting that the system is capable of obtaining good moisture separation capability. (author)

  16. Electrochemistry of Water-Cooled Nuclear Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Macdonald, Dgiby; Urquidi-Macdonald, Mirna; Pitt, Jonathan

    2006-08-08

    This project developed a comprehensive mathematical and simulation model for calculating thermal hydraulic, electrochemical, and corrosion parameters, viz. temperature, fluid flow velocity, pH, corrosion potential, hydrogen injection, oxygen contamination, stress corrosion cracking, crack growth rate, and other important quantities in the coolant circuits of water-cooled nuclear power plants, including both Boiling Water Reactors (BWRs) and Pressurized Water Reactors (PWRs). The model is being used to assess the three major operational problems in Pressurized Water Reactors (PWR), which include mass transport, activity transport, and the axial offset anomaly, and provide a powerful tool for predicting the accumulation of SCC damage in BWR primary coolant circuits as a function of operating history. Another achievement of the project is the development of a simulation tool to serve both as a training tool for plant operators and as an engineering test-bed to evaluate new equipment and operating strategies (normal operation, cold shut down and others). The development and implementation of the model allows us to estimate the activity transport or "radiation fields" around the primary loop and the vessel, as a function of the operating parameters and the water chemistry.

  17. Probabilistic analysis of PWR and BWR fuel rod performance using the code CASINO-SLEUTH

    Energy Technology Data Exchange (ETDEWEB)

    Bull, A.J.

    1987-05-01

    This paper presents a brief description of the Monte Carlo and response surface techniques used in the code, and a probabilistic analysis of fuel rod performance in PWR and BWR applications. The analysis shows that fission gas release predictions are very sensitive to changes in certain of the code's inputs, identifies the most dominant input parameters and compares their effects in the two cases.

  18. Analysis of BWR/Mark III drywell failure during degraded core accidents

    Energy Technology Data Exchange (ETDEWEB)

    Yang, J.W.

    1983-01-01

    The potential for a hydrogen detonation due to the accumulation of a large amount of hydrogen in the drywell region of a BWR Mark III containment is analyzed. Loss of integrity of the drywell wall causes a complete bypass of the suppression pool and leads to pressurization of the containment building. However, the predicted peak containment pressure does not exceed the estimates of containment failure pressure.

  19. Analysis of Core Physics Experiments on Irradiated BWR MOX Fuel in REBUS Program

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, Toru; Ando, Yoshihira [Japan Nuclear Energy Safety Organization, Safety Standard Division, Tokyo (Japan); Hayashi, Yamato [Toshiba Corporation, Power System Company, Yokohama (Japan)

    2008-07-01

    As part of analyses of experimental data of a critical core containing a irradiated BWR MOX test bundle in the REBUS program, depletion calculations was performed for the BWR MOX fuel assemblies from that the MOX test rods were selected by using a general purpose neutronics code system SRAC. The core analyses were carried out using SRAC and a continuous energy Monte Carlo code MVP. The calculated k{sub eff}s were compared with those of the core containing a fresh MOX fuel bundle in the program. The SRAC-diffusion calculation underestimates k{sub eff}s of the both cores by 1.0 to 1.3 %dk and the k{sub eff}s of MVP are 1.001. The difference in k{sub eff} between the irradiated BWR MOX test bundle core and the fresh MOX one is 0.4 %dk in the SRAC-diffusion calculation and 0.0 %dk in the MVP calculation. The calculated fission rate distributions are in good agreement with the measurement in the SRAC-diffusion and MVP calculations. The calculated neutron flux distributions are also in good agreement with the measurement. The calculated burnup reactivity in the both calculations well reproduce the measurements. (authors)

  20. MELCOR 1.8.2 assessment: The DF-4 BWR Damaged Fuel experiment

    Energy Technology Data Exchange (ETDEWEB)

    Tautges, T.J.

    1993-10-01

    MELCOR is a fully integrated, engineering-level computer code being developed at Sandia National Laboratories for the USNRC, that models the entire spectrum of severe accident phenomena in a unified framework for both BWRs and PWRs. As a part of an ongoing assessment, program, MELCOR has been used to model the ACRR in-pile DF-4 Damaged Fuel experiment. DF-4 provided data for early phase melt progression in BWR fuel assemblies, particularly for phenomena associated with eutectic interactions in the BWR control blade and zircaloy oxidation in the canister and cladding. MELCOR provided good agreement with experimental data in the key areas of eutectic material behavior and canister and cladding oxidation. Several shortcomings associated with the MELCOR modeling of BWR geometries were found and corrected. Twenty-five sensitivity studies were performed on COR, HS and CVH parameters. These studies showed that the new MELCOR eutectics model played an important role in predicting control blade behavior. These studies revealed slight time step dependence and no machine dependencies. Comparisons made with the results from four best-estimate codes showed that MELCOR did as well as these codes in matching DF-4 experimental data.

  1. Status of NDE research in the US-contributions of NDE to reactor safety and implementation of NDE technology

    Energy Technology Data Exchange (ETDEWEB)

    Ammirato, F. [EPRI, Charlotte, NC (United States)

    1999-08-01

    Power plant designers, plant owners, and regulators have developed inservice inspection (ISI) programs as part of their comprehensive approach to ensuring nuclear safety. This paper examines the role of ISI in reactor safety through several examples drawn from recent industry initiatives to address implementation of effective examination technology for nuclear power plant piping, and BWR and PWR reactor pressure vessels. These examples also illustrate the importance of well designed performance demonstration activities to support application of effective ISI. Finally, the efforts required to implement effective ISI technology for field inspection is addressed. (orig./DGE)

  2. A simplified model of decontamination by BWR steam suppression pools

    Energy Technology Data Exchange (ETDEWEB)

    Powers, D.A.

    1997-05-01

    Phenomena that can decontaminate aerosol-laden gases sparging through steam suppression pools of boiling water reactors during reactor accidents are described. Uncertainties in aerosol properties, aerosol behavior within gas bubbles, and bubble behavior in plumes affect predictions of decontamination by steam suppression pools. Uncertainties in the boundary and initial conditions that are dictated by the progression of severe reactor accidents and that will affect predictions of decontamination by steam suppression pools are discussed. Ten parameters that characterize boundary and initial condition uncertainties, nine parameters that characterize aerosol property and behavior uncertainties, and eleven parameters that characterize uncertainties in the behavior of bubbles in steam suppression pools are identified. Ranges for the values of these parameters and subjective probability distributions for parametric values within the ranges are defined. These uncertain parameters are used in Monte Carlo uncertainty analyses to develop uncertainty distributions for the decontamination that can be achieved by steam suppression pools and the size distribution of aerosols that do emerge from such pools. A simplified model of decontamination by steam suppression pools is developed by correlating features of the uncertainty distributions for total decontamination factor, DF(total), mean size of emerging aerosol particles, d{sub p}, and the standard deviation of the emerging aerosol size distribution, {sigma}, with pool depth, H. Correlations of the median values of the uncertainty distributions are suggested as the best estimate of decontamination by suppression pools. Correlations of the 10 percentile and 90 percentile values of the uncertainty distributions characterize the uncertainty in the best estimates. 295 refs., 121 figs., 113 tabs.

  3. An overview of zinc addition for BWR dose rate control

    Energy Technology Data Exchange (ETDEWEB)

    Marble, W.J. [GE Nuclear Energy, San Jose, CA (United States)

    1995-03-01

    This paper presents an overview of the BWRs employing feedwater zinc addition to reduce primary system dose rates. It identifies which BWRs are using zinc addition and reviews the mechanical injection and passive addition hardware currently being employed. The impact that zinc has on plant chemistry, including the factor of two to four reduction in reactor water Co-60 concentrations, is discussed. Dose rate results, showing the benefits of implementing zinc on either fresh piping surfaces or on pipes with existing films are reviewed. The advantages of using zinc that is isotopically enhanced by the depletion of the Zn-64 precursor to Zn-65 are identified.

  4. REACTOR COOLING

    Science.gov (United States)

    Quackenbush, C.F.

    1959-09-29

    A nuclear reactor with provisions for selectively cooling the fuel elements is described. The reactor has a plurality of tubes extending throughout. Cylindrical fuel elements are disposed within the tubes and the coolant flows through the tubes and around the fuel elements. The fuel elements within the central portion of the reactor are provided with roughened surfaces of material. The fuel elements in the end portions of the tubes within the reactor are provlded with low conduction jackets and the fuel elements in the region between the central portion and the end portions are provided with smooth surfaces of high heat conduction material.

  5. The influence of cutting speed and feed rate in surface integrity of aisi 1045//Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045

    National Research Council Canada - National Science Library

    Mario Jacas-Cabrera; Tania Rodríguez-Moliner; José Luís Lopes-Da Silveira

    2015-01-01

    El objetivo de esta investigación es el estudio de la influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero AISI-1045, sometido a un proceso de torneado...

  6. Influencia de los dilutores Tris y Ovine freezing sobre la integridad de la membrana citoplasmatica durante la congelacion de semen de ovinos en pajillas de 0.5 ml

    National Research Council Canada - National Science Library

    Cabrera V., Prospero; Pantoja A., Cesar

    2008-01-01

    Se analizo el efecto de los dilutores Tris-glucosa y Ovine Freezing Buffer (UA 466/ 005238) sobre la motilidad e integridad de la membrana citoplasmatica de los espermatozoides durante el proceso de congelacion de semen ovino...

  7. Logical model for the control of a BWR turbine;Modelo logico para el control de una turbina de un BWR

    Energy Technology Data Exchange (ETDEWEB)

    Vargas O, Y. [Universidad del Valle de Mexico, Campus Toluca, Av. Las Palmas No. 136, Col. San Jorge Pueblo Nuevo, 52140 Metepec, Estado de Mexico (Mexico); Amador G, R.; Ortiz V, J.; Castillo D, R., E-mail: yonaeton@hotmail.co [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2009-07-01

    In this work a design of a logical model is presented for the turbine control of a nuclear power plant with a BWR like energy source. The model is sought to implement later on inside the thermal hydraulics code of better estimate RELAP/SCDAPSIM. The logical model is developed for the control and protection of the turbine, and the consequent protection to the BWR, considering that the turbine control will be been able to use for one or several turbines in series. The quality of the present design of the logical model of the turbine control is that it considers the most important parameters in the operation of a turbine, besides that they have incorporated to the logical model the secondary parameters that will be activated originally as true when the turbine model is substituted by a detailed model. The development of the logical model of a turbine will be of utility in the short and medium term to carry out analysis on the turbine operation with different operation conditions, of vapor extraction, specific steps of the turbine to feed other equipment s, in addition to analyze the separate and the integrated effect. (Author)

  8. metodología para la evaluación de integridad en pozos con calentamiento eléctrico

    Directory of Open Access Journals (Sweden)

    JULIO PÉREZ

    2008-01-01

    Full Text Available La integridad de los equipos en la Industria Petrolera, es de gran importancia por razones de seguridad, cumplimiento con regulaciones ambientales, reducción de costos de mantenimiento y prevención de paros inesperados de producción. El objetivo de este artículo es establecer una metodología para evaluar la integridad de pozos que utilicen el Calentamiento Eléctrico como método de recobro mejorado, de tal manera que se pueda definir si los pozos en estudio se encuentran en condiciones mecánico - metalúrgica adecuadas para implementar dicho método. La metodología propuesta se divide en tres etapas como son: planeación, criterios de evaluación y análisis de resultados. La planeación está dirigida hacia la elaboración de un plan de trabajo que será realizado en el sistema con el propósito de recolectar información histórica de inspección, mantenimiento y cálculos de velocidad de corrosión; para evaluar las condiciones actuales se utiliza una matriz de evaluación que determina la aplicabilidad del método de calentamiento eléctrico en los pozos en función de los parámetros que definen el ambiente del sistema y del material del revestimiento; luego de analizar los resultados el ingeniero de corrosión da su juicio determinando si el pozo es apto para la aplicación del método de recobro. Finalmente el artículo muestra dos ejemplos de aplicación de la metodología a pozos del campo La Hocha de la empresa (HOCOL S.A. que se encuentran ubicados en Huila – Colombia. El mayor aporte de este artículo a la industria petrolera, es el desarrollo de una metodología que permita evaluar en forma conjunta diferentes parámetros estructurales y de operación para dar un diagnóstico del pozo antes de diseñar e implementar el calentamiento eléctrico como método de recobro, evitando de esta forma pérdidas económicas.

  9. Implementation of a methodology to perform the uncertainty and sensitivity analysis of the control rod drop in a BWR

    Energy Technology Data Exchange (ETDEWEB)

    Reyes F, M. del C.

    2015-07-01

    A methodology to perform uncertainty and sensitivity analysis for the cross sections used in a Trace/PARCS coupled model for a control rod drop transient of a BWR-5 reactor was implemented with the neutronics code PARCS. A model of the nuclear reactor detailing all assemblies located in the core was developed. However, the thermohydraulic model designed in Trace was a simple model, where one channel representing all the types of assemblies located in the core, it was located inside a simple vessel model and boundary conditions were established. The thermohydraulic model was coupled with the neutronics model, first for the steady state and then a Control Rod Drop (CRD) transient was performed, in order to carry out the uncertainty and sensitivity analysis. To perform the analysis of the cross sections used in the Trace/PARCS coupled model during the transient, Probability Density Functions (PDFs) were generated for the 22 parameters cross sections selected from the neutronics parameters that PARCS requires, thus obtaining 100 different cases for the Trace/PARCS coupled model, each with a database of different cross sections. All these cases were executed with the coupled model, therefore obtaining 100 different outputs for the CRD transient with special emphasis on 4 responses per output: 1) The reactivity, 2) the percentage of rated power, 3) the average fuel temperature and 4) the average coolant density. For each response during the transient an uncertainty analysis was performed in which the corresponding uncertainty bands were generated. With this analysis it is possible to observe the results ranges of the responses chose by varying the uncertainty parameters selected. This is very useful and important for maintaining the safety in the nuclear power plants, also to verify if the uncertainty band is within of safety margins. The sensitivity analysis complements the uncertainty analysis identifying the parameter or parameters with the most influence on the

  10. ATRIUM™ 11 – Validation of performanceand value for BWR operations

    Energy Technology Data Exchange (ETDEWEB)

    Colet, S.; Garner, N.L.; Graebert, R.; Koch, R.; Mollard, P.

    2015-07-01

    AREVA’s ATRIUM™ 11 advanced fuel design for Boiling Water Reactors (BWRs) is the result of a product development program designed to realize a strict set of performance and reliability objectives complying with the industry market demand. The validation of ATRIUM™ 11 performance is given by the now completed out of pile thermal hydraulic and mechanical tests, the results of poolside examinations of initiated lead fuel assembly programs as well as the results of fuel cycle analyses taking benefit of enhanced fuel reliability and operational flexibility. The coming three years will complete the in-service qualification program leading to the anticipated reload deliveries in Europe in 2018 and leading to reload readiness in the US in 2019. The ATRIUM™ 11 Lead Fuel Assembly program is running in Europe since 2012 and in the USA since 2015 and the first irradiation experience data give as-expected results in term of mechanical and thermal-mechanical behavior as well as levels of corrosion. The large gains in term of fuel cycle economy by switching from 10x10 fuel to ATRIUM™ 11 fuel are illustrated specifically for a 1300 MWe US type reactor featuring a symmetric lattice and operated on a 24 month basis. The analytical tools necessary to support cycle design and licensing were initiated in parallel with the product development and, where required by regulatory authorities, submitted for review in time to allow for approval in parallel with the completion of the in-service qualification program. (Author)

  11. Efecto de la manipulación del semen criopreservado de bovinos Bos Taurus sobre la integridad espermática

    Directory of Open Access Journals (Sweden)

    Norberto Villa-Duque

    2016-01-01

    Full Text Available En el estudio se evaluó el efecto de descongelar y aplicar semen de bovinos Bos Taurus en 33 ganaderías del Magdalena Medio colombiano, y se estudió in vitro el efecto de la injuria encontrada sobre la integridad de las membranas espermáticas. La información en fincas se recopiló mediante formulario específico, mientras que el estudio in vitro se ejecutó en el laboratorio de Biotecnología Reproductiva Animal del Instituto Universitario de la Paz (Barrancabermeja, Santander. El estudio consistió en someter pajillas comerciales de 0.5 ml de toros Holstein y Pardo Suizo a la técnica convencional y a tres modificaciones de esta (injurias mediante un diseño randomizado. Ninguna de las fincas evaluadas aplicó correctamente la práctica de la inseminación artificial; errores notorios fueron: exceso de tiempo durante la extracción de la pajilla, descongelación en la región axilar y no combinación correcta entre tiempo y temperatura. Los resultados evidenciaron diferencia significativa (P<0.05 por efecto de la raza para la integridad y resistencia de las membranas espermáticas, para la integridad de las membranas por efecto de los tratamientos cuando la pajilla se descongelo a temperatura corporal en la región axilar y para la integridad de la membrana acrosomal cuando la extracción de la pajilla se realizó en forma incorrecta. El semen de la raza Holstein evidencia una ligera tendencia a ser más resistente que el de la raza Pardo Suizo.

  12. Multifunctional reactors

    NARCIS (Netherlands)

    Westerterp, K.R.

    1992-01-01

    Multifunctional reactors are single pieces of equipment in which, besides the reaction, other functions are carried out simultaneously. The other functions can be a heat, mass or momentum transfer operation and even another reaction. Multifunctional reactors are not new, but they have received much

  13. Automatic boiling water reactor control rod pattern design using particle swarm optimization algorithm and local search

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Cheng-Der, E-mail: jdwang@iner.gov.tw [Nuclear Engineering Division, Institute of Nuclear Energy Research, No. 1000, Wenhua Rd., Jiaan Village, Longtan Township, Taoyuan County 32546, Taiwan, ROC (China); Lin, Chaung [National Tsing Hua University, Department of Engineering and System Science, 101, Section 2, Kuang Fu Road, Hsinchu 30013, Taiwan (China)

    2013-02-15

    Highlights: ► The PSO algorithm was adopted to automatically design a BWR CRP. ► The local search procedure was added to improve the result of PSO algorithm. ► The results show that the obtained CRP is the same good as that in the previous work. -- Abstract: This study developed a method for the automatic design of a boiling water reactor (BWR) control rod pattern (CRP) using the particle swarm optimization (PSO) algorithm. The PSO algorithm is more random compared to the rank-based ant system (RAS) that was used to solve the same BWR CRP design problem in the previous work. In addition, the local search procedure was used to make improvements after PSO, by adding the single control rod (CR) effect. The design goal was to obtain the CRP so that the thermal limits and shutdown margin would satisfy the design requirement and the cycle length, which is implicitly controlled by the axial power distribution, would be acceptable. The results showed that the same acceptable CRP found in the previous work could be obtained.

  14. EVALUACIÓN DE LA INTEGRIDAD DE CIMENTACIONES PROFUNDAS: ANÁLISIS Y VERIFICACIÓN IN SITU

    Directory of Open Access Journals (Sweden)

    CARLOS ANDRES GAVIRIA

    2009-01-01

    Full Text Available Las cimentaciones profundas son usadas con el fin de brindar estabilidad a una variedad de estructuras tales como puentes, presas y edificaciones en condiciones donde las cimentaciones superficiales no la proporcionan. En consecuencia, ha surgido la necesidad de evaluar la calidad de este tipo de cimentaciones y descartar cualquier anomalía generada durante su proceso constructivo, motivo por el cual se han implementado los ensayos no destructivos, entre ellos la prueba de integridad de pilotes (PIT que debido a sus bondades como lo son su rapidez y economía sumada a sus resultados, ha despertado el interés de los investigadores y constructores del medio. En el presente artículo se presentan aspectos generales de la prueba PIT y los resultados de su aplicación en once pilotes en una construcción cerca a la ciudad de Palmira, Colombia. Estos resultados fueron verificados mediante la excavación en dos pilotes en los que la PIT manifestó alguna anomalía, con lo cual se demostró la confiabilidad del método en la determinación de fallas en los elementos estructurales.

  15. La auditoría ética: herramienta para fortalecer la integridad del carácter organizacional

    Directory of Open Access Journals (Sweden)

    María del Pilar Rodríguez Córdoba

    2006-06-01

    Full Text Available El presente artículo parte de una discusión teórica sobre la ética y la ética empresarial para sustentar la posición de los autores en cuanto a la auditoría ética como una herramienta para fortalecer la integridad del carácter organizacional y llevar a la empresa al logro de sus objetivos económicos, sociales y medioambientales. Se propone una metodología cualitativa que busca evaluar el daño y beneficio que resulta de las actividades de la organización, con fines de mejoramiento en su desempeño ético y del cumplimiento de su responsabilidad social. Finalmente se presenta el caso de la Universidad Nacional de Colombia, sede Manizales, donde se está implementando un programa integral de desarrollo ético cuya segunda etapa es la elaboración de una auditoría ética.

  16. The electrochemistry of IGSCC mitigation in BWR coolant circuits

    Energy Technology Data Exchange (ETDEWEB)

    Macdonald, D.D. [Center for Electrochemical Science and Technology, The Pennsylvania State Univ., University Park, PA (United States)

    2002-07-01

    A brief review is presented of the electrochemical mitigation of IGSCC in water-cooled reactor heat transport circuit structural materials. Electrochemical control and mitigation is possible, because of the existence of a critical potential for IGSCC and by the feasibility of modifying the environment to displace the corrosion potential (ECP) to a value that is more negative than the critical value. However, even in cases where the ECP cannot be displaced sufficiently in the negative direction to become more negative than the critical potential, considerable advantage is accrued, because of the roughly exponential dependence of crack growth rate on potential. The most important parameters in affecting electrochemical control over the ECP and crack growth rate are the kinetic parameters (exchange current densities and Tafel constants) for the redox reactions involving the principal radiolysis products of water (O{sub 2}, H{sub 2}, H{sub 2}O{sub 2}), external solution composition (concentrations of O{sub 2}, H{sub 2}O{sub 2}, and H{sub 2}), flow velocity, and the conductivity of the bulk environment. The kinetic parameters for the redox reactions essentially determine the charge transfer impedance of the steel surface, which is shown to be one of the key parameters in affecting the magnitude of the coupling current and hence the crack growth rate. The exchange current densities, in particular, are amenable to control by catalysis or inhibition, with the result that surface modification techniques are highly effective in controlling and mitigating IGSCC in reactor coolant circuit materials. (authors)

  17. BWR spent fuel storage cask performance test. Volume 2. Pre- and post-test decay heat, heat transfer, and shielding analyses

    Energy Technology Data Exchange (ETDEWEB)

    Wiles, L.E.; Lombardo, N.J.; Heeb, C.M.; Jenquin, U.P.; Michener, T.E.; Wheeler, C.L.; Creer, J.M.; McCann, R.A.

    1986-06-01

    This report describes the decay heat, heat transfer, and shielding analyses conducted in support of performance testing of a Ridhihalgh, Eggers and Associates REA 2033 boiling water reactor (BWR) spent fuel storage cask. The cask testing program was conducted for the US Department of Energy (DOE) Commercial Spent Fuel Management Program by the Pacific Northwest Laboratory (PNL) and by General Electric at the latters' Morris Operation (GE-MO) as reported in Volume I. The analyses effort consisted of performing pretest calculations to (1) select spent fuel for the test; (2) symmetrically load the spent fuel assemblies in the cask to ensure lateral symmetry of decay heat generation rates; (3) optimally locate temperature and dose rate instrumentation in the cask and spent fuel assemblies; and (4) evaluate the ORIGEN2 (decay heat), HYDRA and COBRA-SFS (heat transfer), and QAD and DOT (shielding) computer codes. The emphasis of this second volume is on the comparison of code predictions to experimental test data in support of the code evaluation process. Code evaluations were accomplished by comparing pretest (actually pre-look, since some predictions were not completed until testing was in progress) predictions with experimental cask testing data reported in Volume I. No attempt was made in this study to compare the two heat transfer codes because results of other evaluations have not been completed, and a comparison based on one data set may lead to erroneous conclusions.

  18. Experiences with austenitic steels in boiling water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Wachter, O. [Preussische Elektrizitaets-AG (Preussenelektra), Hannover (Germany); Bruemmer, G. [Hamburgische Electricitaets-Werke AG., Hamburg (Germany)

    1997-05-01

    Stabilized austenitic steels are susceptible to intergranular stress corrosion cracking (IGSCC) under boiling water reactor (BWR) conditions. This important finding for the German nuclear power station industry arises from the detection of cracks during the last 3 years in reactor hot water pipes made from titanium-stabilized steel AISI 321 in six BWRs and in reactor core components made from the niobium-stabilized steel AISI 347 in one BWR. All the observed cracks had a common feature: they had their origin in the chromium carbide precipitates at the grain boundaries and in the associated chromium-depleted region near the grain boundary. These microstructural features in the heat-affected zones of the hot water pipe weldments were caused by the heat input during deposition of the root bead. The TiC partially dissolved in the region near the fusion line and the released carbon reacted to form chromium-rich M{sub 23}C{sub 6}. Regarding the cracks found in the core shroud and the core grid plates, it was shown that a sensitizing heat treatment of rings taken from the same heat of steel could give rise to a microstructure susceptible to IGSCC in the region of a weldment. High carbon contents coupled with low stabilization ratios led to sensitization. Residual stresses developed during welding provided the significant contributions to the tensile stress necessary for IGSCC. With regard to the service medium, the influence of the electrochemical corrosion potential (ECP) was recognized as a dominant factor, together with the conductivity. The corrosion potential was mainly determined by the radiolytic formation of H{sub 2}O{sub 2}; with increasing distance from the core, the H{sub 2}O{sub 2} content decreased owing to catalytic decomposition. For the pipes the problem of IGSCC could be resolved by the use of optimized steel (lower carbon content with maximum allowable stabilization ratio).

  19. Mitigating IASCC of Reactor Core Internals by Post-Irradiation Annealing

    Energy Technology Data Exchange (ETDEWEB)

    Was, Gary [Univ. of Michigan, Ann Arbor, MI (United States)

    2017-06-02

    This final report summarizes research performed during the period between September 2012 and December 2016, with the objective of establishing the effectiveness of post-irradiation annealing (PIA) as an advanced mitigation strategy for irradiation-assisted stress corrosion cracking (IASCC). This was completed by using irradiated 304SS control blade material to conduct crack initiation and crack growth rate (CGR) experiments in simulated BWR environment. The mechanism by which PIA affects IASCC susceptibility will also be verified. The success of this project will provide a foundation for the use of PIA as a mitigation strategy for core internal components in commercial reactors.

  20. Best estimate approach for the evaluation of critical heat flux phenomenon in the boiling water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kaliatka, Tadas; Kaliatka, Algirdas; Uspuras, Eudenijus; Vaisnoras, Mindaugas [Lithuanian Energy Institute, Kaunas (Lithuania); Mochizuki, Hiroyasu; Rooijen, W.F.G. van [Fukui Univ. (Japan). Research Inst. of Nuclear Engineering

    2017-05-15

    Because of the uncertainties associated with the definition of Critical Heat Flux (CHF), the best estimate approach should be used. In this paper the application of best-estimate approach for the analysis of CHF phenomenon in the boiling water reactors is presented. At first, the nodalization of RBMK-1500, BWR-5 and ABWR fuel assemblies were developed using RELAP5 code. Using developed models the CHF and Critical Heat Flux Ratio (CHFR) for different types of reactors were evaluated. The calculation results of CHF were compared with the well-known experimental data for light water reactors. The uncertainty and sensitivity analysis of ABWR 8 x 8 fuel assembly CHFR calculation result was performed using the GRS (Germany) methodology with the SUSA tool. Finally, the values of Minimum Critical Power Ratio (MCPR) were calculated for RBMK-1500, BWR-5 and ABWR fuel assemblies. The paper demonstrate how, using the results of sensitivity analysis, to receive the MCPR values, which covers all uncertainties and remains best estimated.

  1. THERMIT2. BWR & PWR Thermal-Hydraulic Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Kazimi, M.S.; Kao, S.P.; Kelly, J.E. [Massachusetts Institute of Technology, Cambridge, MA (United States)

    1992-02-27

    THERMIT2, the most recent release of THERMIT, is intended for thermal-hydraulic analysis of both boiling and pressurized water reactor cores. It solves the three-dimensional, two-fluid equations describing the two-phase flow and heat transfer dynamics in rectangular coordinates. The two-fluid model uses separate partial differential equations expressing conservation of mass, momentum, and energy for each fluid. By expressing the exchange of mass, momentum, and energy between the fluids with physically-based mathematical models, the relative motion and thermal non-equilibrium between the fluids can exist. THERMIT2 offers the choice of either pressure or velocity boundary conditions at the top and bottom of the core. THERMIT2 includes a two-phase turbulent mixing model which provides subchannel analysis capability. THERMIT2 also solves the radial heat conduction equations for fuel pin temperatures, and calculates the heat flux from fuel pin to coolant with appropriate heat transfer models described by a boiling curve.

  2. NUCLEAR REACTOR

    Science.gov (United States)

    Miller, H.I.; Smith, R.C.

    1958-01-21

    This patent relates to nuclear reactors of the type which use a liquid fuel, such as a solution of uranyl sulfate in ordinary water which acts as the moderator. The reactor is comprised of a spherical vessel having a diameter of about 12 inches substantially surrounded by a reflector of beryllium oxide. Conventionnl control rods and safety rods are operated in slots in the reflector outside the vessel to control the operation of the reactor. An additional means for increasing the safety factor of the reactor by raising the ratio of delayed neutrons to prompt neutrons, is provided and consists of a soluble sulfate salt of beryllium dissolved in the liquid fuel in the proper proportion to obtain the result desired.

  3. NUCLEAR REACTOR

    Science.gov (United States)

    Grebe, J.J.

    1959-07-14

    High temperature reactors which are uniquely adapted to serve as the heat source for nuclear pcwered rockets are described. The reactor is comprised essentially of an outer tubular heat resistant casing which provides the main coolant passageway to and away from the reactor core within the casing and in which the working fluid is preferably hydrogen or helium gas which is permitted to vaporize from a liquid storage tank. The reactor core has a generally spherical shape formed entirely of an active material comprised of fissile material and a moderator material which serves as a diluent. The active material is fabricated as a gas permeable porous material and is interlaced in a random manner with very small inter-connecting bores or capillary tubes through which the coolant gas may flow. The entire reactor is divided into successive sections along the direction of the temperature gradient or coolant flow, each section utilizing materials of construction which are most advantageous from a nuclear standpoint and which at the same time can withstand the operating temperature of that particular zone. This design results in a nuclear reactor characterized simultaneously by a minimum critiral size and mass and by the ability to heat a working fluid to an extremely high temperature.

  4. Environmentally-Assisted Cracking of Low-Alloy Reactor Pressure Vessel Steels under Boiling Water Reactor Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Seifert, H.P.; Ritter, S

    2002-02-01

    The present report summarizes the experimental work performed by PSI on the environmentally-assisted cracking (EAC) of low-alloy steels (LAS) in the frame of the RIKORR-project during the period from January 2000 to August 2001. Within this project, the EAC crack growth behaviour of different low-alloy reactor pressure vessel (RPV) steels, weld filler and weld heat-affected zone materials is investigated under simulated transient and steady-state BWR/NWC power operation conditions. The EAC crack growth behaviour of different low-alloy RPV steels was characterized by slow rising load (SRL) / low-frequency corrosion fatigue (LFCF) and constant load tests with pre-cracked fracture mechanics specimens in oxygenated high-temperature water at temperatures of either 288, 250, 200 or 150 C. These tests revealed the following important interim results: Under low-flow and highly oxidizing (ECP >= 100 mV SHE) conditions, the ASME XI 'wet' reference fatigue crack growth curve could be significantly exceeded by cyclic fatigue loading at low frequencies (<0.001 Hz), at high and low load-ratios R, and by ripple loading near to DKth fatigue thresholds. The BWR VIP 60 SCC disposition lines may be significantly or slightly exceeded (even in steels with a low sulphur content) in the case of small load fluctuations at high load ratios (ripple loading) or at intermediate temperatures (200 -250 C) in RPV materials, which show a distinct susceptibility to dynamic strain ageing (DSA). (author)

  5. Feasibility Study of Supercritical Light Water Cooled Fast Reactors for Actinide Burning and Electric Power Production, 3rd Quarterly Report

    Energy Technology Data Exchange (ETDEWEB)

    Mac Donald, Philip Elsworth

    2002-06-01

    The use of light water at supercritical pressures as the coolant in a nuclear reactor offers the potential for considerable plant simplification and consequent capital and O&M cost reduction compared with current light water reactor (LWR) designs. Also, given the thermodynamic conditions of the coolant at the core outlet (i.e. temperature and pressure beyond the water critical point), very high thermal efficiencies of the power conversion cycle are possible (i.e. up to about 45%). Because no change of phase occurs in the core, the need for steam separators and dryers as well as for BWR-type re-circulation pumps is eliminated, which, for a given reactor power, results in a substantially shorter reactor vessel and smaller containment building than the current BWRs. Furthermore, in a direct cycle the steam generators are not needed.

  6. An analysis of the thermodynamic cycles with high-temperature nuclear reactor for power generation and hydrogen co-production

    Directory of Open Access Journals (Sweden)

    Dudek Michał

    2017-01-01

    Full Text Available In the present paper, numerical analysis of the thermodynamic cycle with the high-temperature nuclear gas reactor (HTGR for electricity and hydrogen production have been done. The analysed system consists of two independent loops. The first loop is for HTGR and consists of a nuclear reactor, heat exchangers, and blower. The second loop (Rankine cycle consist of up-to four steam turbines, that operate in heat recovery system. The analysis of the system shows that it is possible to achieve significantly higher efficiency than could be offered by traditional nuclear reactor technology (PWR and BWR. It is shown that the thermal efficiency about 52.5% it is possible to achieve when reactor works at standard conditions and steam is superheated up to 530oC. For the cases when the steam has supercritical conditions the value of thermal efficiency is still very high and equal about 50%.

  7. Non-disturbance technique to estimate the core stability of BWR

    Energy Technology Data Exchange (ETDEWEB)

    Shieh, D.J.; Chang, S.I.

    1980-09-01

    The feasibility of estimating the core instability margin of BWR by analyzing the fluctuation of normal operation neutron flux signal is surveyed. It concludes that the instability margin estimated by this technique will be comparable with the small reactivity perturbation test result. The DDS method used to estimate the natural frequency and decay ratio is briefly described and verified by some simulation cases. Then the APRM signal taken from Chin-Shan Nuclear Power Station Unit 1 is analyzed. The result shows that the natural frequency is 0.777 +- 0.039 Hz, and the decay ratio is 0.277 +- 0.045.

  8. An on-line method to monitor BWR core stability based on an autocorrelation method

    Energy Technology Data Exchange (ETDEWEB)

    Yokomizo, Osamu; Masuhara, Yasuhiro (Hitachi Ltd., Ibaraki (Japan). Energy Research Lab.); Yoshimoto, Yuichiro (Hitachi Ltd., Ibaraki (Japan). Hitachi Works)

    1990-03-01

    A on-line monitoring method is introduced for BWR core stability. The method utilizes only autocorrelation values for two delay time intervals. Its simplicity makes it suitable for an on-line monitor. Accuracy of the core decay ratio calculated by the method improves as the core condition approaches instability. The error in the decay ratio for regional limit cycle oscillations is 0.2% when calculated from local signals in the most unstable region, and 4% when calculated from core averaged signals. (orig.).

  9. Effect of nonuniform 3-D void distribution within BWR fuel assemblies on neutronic characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Toshikazu; Hyoudou, Hideaki; Kitada, Takanori [Osaka Univ., Suita (Japan). Dept. of Nuclear Engineering]. E-mail: takeda@nucl.eng.osaka-u.ac.jp; Kosaka, Shinya; Ikeda, Hideaki [Tepco Systems Corp., Tokyo (Japan)]. E-mail: kisaka-shinya@tepsys.co.jp

    2003-07-01

    The effect of nonuniform distribution of void fractions within fuel assemblies of BWR cores on the neutronic characteristics has been evaluated by coupling the thermal hydraulic and neutronic calculations. It is found that the effect is large for assemblies with Gd rods because of the small void fraction for subchannels with Gd rods. The axially averaged K{sub {infinity}} is reduced by about 0.1 {approx} 0.3% {delta}k/k compared with the case with uniform void distribution. The power peaking is decreased by 0.6 {approx} 1.3%. The reason of these changes is discussed. (author)

  10. TRACE code validation for BWR spray cooling injection based on GOTA facility experiments

    Energy Technology Data Exchange (ETDEWEB)

    Racca, S. [San Piero a Grado Nuclear Research Group (GRNSPG), Pisa (Italy); Kozlowski, T. [Royal Inst. of Tech., Stockholm (Sweden)

    2011-07-01

    Best estimate codes have been used in the past thirty years for the design, licensing and safety of NPP. Nevertheless, large efforts are necessary for the qualification and the assessment of such codes. The aim of this work is to study the main phenomena involved in the emergency spray cooling injection in a Swedish designed BWR. For this purpose, data from the Swedish separate effect test facility GOTA have been simulated using TRACE version 5.0 Patch 2. Furthermore, uncertainty calculations have been performed with the propagation of input errors method and the identification of the input parameters that mostly influence the peak cladding temperature has been performed. (author)

  11. Áreas de alta consecuencia en la gestión de integridad de oleoductos en Colombia

    Directory of Open Access Journals (Sweden)

    Omar Javier Daza Leguizamón , Rigaud Sanabria Marín y Enrique Vera López

    2011-05-01

    Full Text Available En Colombia,  los  sistemas  de  gestión  de  integridad de  las  tuberías  que  transportan  líquidos  peligrosos están  en proceso de  estandarización  por  el  Instituto Colombiano  de Normas Técnicas  y Certificación.Dentro del proyecto de esta nueva norma  técnica se definen  las  áreas  de  alta  consecuencia,   su identificación  e  importancia  dentro  del  proceso  de gestión  de  tuberías;  pero  en  nuestro  entorno  la información  espacial y  no  espacial para  la  correctaidentificación de estas áreas es de difícil adquisición o no está disponible; por ello, con este artículo se busca dar una primera mirada a este  tipo de zonas  a nivel nacional  y  presentar  sus  posibles  fuentes  de información, bajo estándares y normas  internacionales.También  se  presentan metodologías  basadas  en sistemas  de  información geográfica,  implementadas a escala internacional, para su identificación.

  12. Desarrollo de software para el análisis probabilístico de integridad de ductos

    Directory of Open Access Journals (Sweden)

    José de Jesús Silva-Lomelí

    2012-01-01

    Full Text Available Una de las aplicaciones de la mecánica de la fractura probabilística (MFP es el estudio de oleogasoductos, este procedimiento se basa en la determinación de la probabilidad, en donde variables aleatorias como: cargas aplicadas, propiedades mecánicas del material, geometría del ducto y grietas, pueden ocasionar la falla de una estructura. Utilizando el método Monte Carlo escenarios múltiples, introduciendo valores aleatorios a partir de las distribuciones de probabilidad tanto de carga como de resistencia. El resultado obtenido de este análisis es una distribución estadística de la probabilidad de falla; mientras que la mecánica de fractura determinística (MFD solamente genera el valor de JIc para fractura elasto-plástica (MFEP de ciertos valores previos. De esta manera, los análisis probabilísticos proporcionan un panorama más completo de la situación real de la integridad de ductos. La aplicación de la MFP reemplaza el factor de seguridad clásico N por el concepto de confiabilidad estructural. De esta manera, el análisis de riesgo basado en la mecánica de fractura probabilística permite incrementar el nivel de seguridad en oleogasoductos y al mismo tiempo disminuir los costos de mantenimiento. Este trabajo considera los siguinetes puntos: a. Determinar dos ecuaciones determinísticas para la Integral Ja y Jc. b. Crear un programa generatedo en el ambiente MATLAB, este código muestra los procesos determinísticos y probabilísticos del análisis de ductos, con una relación Ri/t = 43.6 para mecánica de fractura elastoplástica.

  13. Effect of nonlinear void reactivity on bifurcation characteristics of a lumped-parameter model of a BWR: A study relevant to RBMK

    Energy Technology Data Exchange (ETDEWEB)

    Verma, Dinkar, E-mail: dinkar@iitk.ac.in [Nuclear Engineering and Technology Program, Indian Institute of Technology Kanpur, Kanpur 208 016 (India); Kalra, Manjeet Singh, E-mail: drmanjeet.singh@dituniversity.edu.in [DIT University, Dehradun 248 009 (India); Wahi, Pankaj, E-mail: wahi@iitk.ac.in [Department of Mechanical Engineering, Indian Institute of Technology Kanpur, Kanpur 208 016 (India)

    2017-04-15

    Highlights: • A simplified model with nonlinear void reactivity feedback is studied. • Method of multiple scales for nonlinear analysis and oscillation characteristics. • Second order void reactivity dominates in determining system dynamics. • Opposing signs of linear and quadratic void reactivity enhances global safety. - Abstract: In the present work, the effect of nonlinear void reactivity on the dynamics of a simplified lumped-parameter model for a boiling water reactor (BWR) is investigated. A mathematical model of five differential equations comprising of neutronics and thermal-hydraulics encompassing the nonlinearities associated with both the reactivity feedbacks and the heat transfer process has been used. To this end, we have considered parameters relevant to RBMK for which the void reactivity is known to be nonlinear. A nonlinear analysis of the model exploiting the method of multiple time scales (MMTS) predicts the occurrence of the two types of Hopf bifurcation, namely subcritical and supercritical, leading to the evolution of limit cycles for a range of parameters. Numerical simulations have been performed to verify the analytical results obtained by MMTS. The study shows that the nonlinear reactivity has a significant influence on the system dynamics. A parametric study with varying nominal reactor power and operating conditions in coolant channel has also been performed which shows the effect of change in concerned parameter on the boundary between regions of sub- and super-critical Hopf bifurcations in the space constituted by the two coefficients of reactivities viz. the void and the Doppler coefficient of reactivities. In particular, we find that introduction of a negative quadratic term in the void reactivity feedback significantly increases the supercritical region and dominates in determining the system dynamics.

  14. Inspection findings in austenitic RPV internals of German BWR plants and BWRs built in other countries and resulting measures for Isar 1 nuclear power station

    Energy Technology Data Exchange (ETDEWEB)

    Erve, M.; Hurlebaus, D.; Marschke, D.; Senski, G. [Siemens AG, Erlangen (Germany). Power Generation Group; Maier, V. [Bayernwerk Kernenergie GmbH, Muenchen (Germany); Baeumler, H.-J.; Winter, F. [TUeV Anlagen-und Umwetttechnik GmbH, Muenchen (Germany)

    1999-06-01

    As visual examinations carried out in autumn 1994 detected cracks in a German BWR plant due to intergranular stress corrosion cracking (IGSCC) in several core shroud components manufactured from 1.4550 steel, precautionary examinations and assessments were performed for all other plants. In accordance with these analyses, it can be stated for Isar 1 that the heat treatment to which the components in question were subjected in the course of manufacture cannot have caused sensitization of the material, and that crack formation due to the damage mechanism primarily identified in the reactor vessel internals at Wuergassen Nuclear Power Station need not be feared. Although the material and corrosion-chemical assessments performed to date did not give any indications for the other crack formation mechanisms that are theoretically relevant for reactor vessel internals (IGSCC due to weld sensitization, IASCC (irradiation assisted stress corrosion cracking)), visual examinations with a limited scope will be carried out with the independant expert`s agreement during the scheduled inservice inspections. The fluid-dynamic and structure-mechanical analyses showed that the individual components are subjected only to low loadings, even in the event of accidents, and that the safety objectives shutdown and residual heat removal can be fulfilled even in the case of large postulated cracks. The fracture-mechanics analyses indicated critical through-wall crack lengths which, however, can be promptly and reliably detected during random inservice inspections even when assuming stress corrosion cracking and irradiation-induced low-toughness material conditions. In addition, both the VGB and the Isar 1 plant are pursuing further prophylactic measures such as alternative water chemistry modes and an appropriate repair and replacement concept. (orig.) 18 refs.

  15. Nuclear reactor core modelling in multifunctional simulators

    Energy Technology Data Exchange (ETDEWEB)

    Puska, E.K. [VTT Energy, Nuclear Energy, Espoo (Finland)

    1999-06-01

    The thesis concentrates on the development of nuclear reactor core models for the APROS multifunctional simulation environment and the use of the core models in various kinds of applications. The work was started in 1986 as a part of the development of the entire APROS simulation system. The aim was to create core models that would serve in a reliable manner in an interactive, modular and multifunctional simulator/plant analyser environment. One-dimensional and three-dimensional core neutronics models have been developed. Both models have two energy groups and six delayed neutron groups. The three-dimensional finite difference type core model is able to describe both BWR- and PWR-type cores with quadratic fuel assemblies and VVER-type cores with hexagonal fuel assemblies. The one- and three-dimensional core neutronics models can be connected with the homogeneous, the five-equation or the six-equation thermal hydraulic models of APROS. The key feature of APROS is that the same physical models can be used in various applications. The nuclear reactor core models of APROS have been built in such a manner that the same models can be used in simulator and plant analyser applications, as well as in safety analysis. In the APROS environment the user can select the number of flow channels in the three-dimensional reactor core and either the homogeneous, the five- or the six-equation thermal hydraulic model for these channels. The thermal hydraulic model and the number of flow channels have a decisive effect on the calculation time of the three-dimensional core model and thus, at present, these particular selections make the major difference between a safety analysis core model and a training simulator core model. The emphasis on this thesis is on the three-dimensional core model and its capability to analyse symmetric and asymmetric events in the core. The factors affecting the calculation times of various three-dimensional BWR, PWR and WWER-type APROS core models have been

  16. Passive Gamma Analysis of the Boiling-Water-Reactor Assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Vo, Duc Ta [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Favalli, Andrea [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-03-31

    Passive gamma analysis can be used to determine BU and CT of BWR assembly. The analysis is somewhat more complicated and less effective than similar method for PWR assemblies. From the measurements along the lengths of the BWR1 and BWR9 assemblies, there are hints that we may be able to use their information to help improve the model functions for better results.

  17. Interpretation of the VENUS VIP-BWR program with APOLLO2.8 reference and optimized MOC schemes for 8 x 8 UO{sub 2} and MOX BWR assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Blaise, P., E-mail: patrick.blaise@cea.f [CEA - Commissariat a l' Energie Atomique, Centre de CADARACHE - DEN/CAD/DER/SPRC, F-13108 Saint Paul-Lez-Durance (France); Vidal, J.-F.; Santamarina, A.; Bernard, D. [CEA - Commissariat a l' Energie Atomique, Centre de CADARACHE - DEN/CAD/DER/SPRC, F-13108 Saint Paul-Lez-Durance (France)

    2010-11-15

    The interpretation of the VIP-BWR program conducted in the CEN.SCK Mol VENUS critical facility (Belgium), has been performed with the new APOLLO2.8 product and its CEA2005V4.1 library based on the JEFF3.1.1 file. Both reference SHEM-MOC (281groups without equivalence) and Optimized BWR 26G (26 groups with equivalence) schemes are used for UO{sub 2} and MOX BWR assembly calculations. The VIP-BWR program was aimed to provide an experimental database for BWR neutronics tools in mixed Gd poisoned configurations with 8 x 8 UO{sub 2} and MOX assemblies. The experimental conditions are relatively representative of actual industrial BWR core characteristics, at least in terms of void fraction. Measured pin-by-pin power distributions enable to exact valuable information at various interfaces. For fresh (UO{sub 2}/UO{sub 2}-Gd) and recycled UO{sub 2} (UO{sub 2} only) cores loadings, the information is given through the 'UO{sub 2}' core. In the case of partial MOX loadings (UO{sub 2}/MOX interface), the power distributions are available through the 'T-MOX' core. All critical sizes are predicted within 1 with SHEM-MOC reference calculation scheme. For UO{sub 2} core, the (C-E) on k{sub eff} are (95 {+-} 266) pcm and (203 {+-} 266) pcm for SHEM-MOC and Optimized scheme respectively. For MOX core, the results are (87 {+-} 214) pcm and (283 {+-} 214) pcm. The uncertainties take into account both measurement uncertainties and technological uncertainties such as enrichment, clad thicknesses, grid pitch or fuel densities. Average (C-E)/E on radial fission rate distributions are in excellent agreement in the UO{sub 2} and UO{sub 2}-Gd assemblies. In mixed loading cores, the calculation shows an over prediction in the MOX fuel pin. This points out a systematic swing between UO{sub 2} and MOX. For average fission rates in UO{sub 2}, the C/E results are within {+-} 0.2% with SHEM-MOC and OptimizedBWR26G. For average power in MOX, the C/E results are within {+-}0

  18. Boiling water reactor radiation shielded Control Rod Drive Housing Supports

    Energy Technology Data Exchange (ETDEWEB)

    Baversten, B.; Linden, M.J. [ABB Combustion Engineering Nuclear Operations, Windsor, CT (United States)

    1995-03-01

    The Control Rod Drive (CRD) mechanisms are located in the area below the reactor vessel in a Boiling Water Reactor (BWR). Specifically, these CRDs are located between the bottom of the reactor vessel and above an interlocking structure of steel bars and rods, herein identified as CRD Housing Supports. The CRD Housing Supports are designed to limit the travel of a Control Rod and Control Rod Drive in the event that the CRD vessel attachement went to fail, allowing the CRD to be ejected from the vessel. By limiting the travel of the ejected CRD, the supports prevent a nuclear overpower excursion that could occur as a result of the ejected CRD. The Housing Support structure must be disassembled in order to remove CRDs for replacement or maintenance. The disassembly task can require a significant amount of outage time and personnel radiation exposure dependent on the number and location of the CRDs to be changed out. This paper presents a way to minimize personal radiation exposure through the re-design of the Housing Support structure. The following paragraphs also delineate a method of avoiding the awkward, manual, handling of the structure under the reactor vessel during a CRD change out.

  19. Fracture mechanics applied to the evaluation of a nuclear reactor vessel structural integrity; Aplicacao da mecanica da fratura na avaliacao da integridade estrutural de um componente nuclear

    Energy Technology Data Exchange (ETDEWEB)

    Tarpani, Jose Ricardo; Spinelli, Dirceu [Sao Paulo Univ., Sao Carlos, SP (Brazil). Escola de Engenharia. Dept. de Engenharia de Materiais

    1995-12-31

    Analytical predictions of PWR vessel instability were made based upon Linear Elastic Fracture Mechanics criterion Kl C and on Elastic-Plastic Fracture Mechanics Ji and J50. special attention was given to the influence of crack depth and aspect ratio for both approaches, as well as to the data extrapolation procedures in the latest. Simple and didactic format is supplied for the evaluation of the final results in terms of internal pressure, strain gradient and ductile crack extension. (author) 7 refs., 6 figs., 6 tabs.

  20. Development of a prototype pin-by-pin fine mesh calculation code for BWR core analysis

    Energy Technology Data Exchange (ETDEWEB)

    Tada, Kenichi; Yamamoto, Akio; Yamane, Yoshihiro [Nagoya University, Nagoya (Japan); Kosaka, Shinya; Hirano, Gou [TEPCO SYSTEMS CORPORATION, Tokyo (Japan)

    2008-07-01

    A prototype core analysis code for BWR, SUBARU, which is based on the three-dimensional pin-by-pin fine-mesh calculation, is being developed. The SUBARU code has several features, e.g., incorporation of the SP3 transport theory, capability to treat the staggered meshes, and so on. In this paper, to estimate the prediction accuracy of this core analysis code, a hypothetical 2D ABWR core which is consisted by 8x8 low-enrichment UO{sub 2} fuel assembly, 9x9 high-enrichment UO{sub 2} fuel assembly, and 10x10 MOX fuel assembly is analyzed. To investigate the prediction accuracy, we compared the pin-wise fission rate distribution which was obtained by the cell-heterogeneous transport calculation by MOC. To evaluate the computational costs, a hypothetical 3D ABWR core is also used. These results suggest that SUBARU would have enough accuracy and reasonable calculation costs for the reference BWR core analysis when further investigation is taken into account. (authors)

  1. On the Decay Ratio Determination in BWR Stability Analysis by Auto-Correlation Function Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Behringer, K.; Hennig, D

    2002-11-01

    A novel auto-correlation function (ACF) method has been investigated for determining the oscillation frequency and the decay ratio in BWR stability analyses. The neutron signals are band-pass filtered to separate the oscillation peak in the power spectral density (PSD) from background. Two linear second-order oscillation models are considered. These models, corrected for signal filtering and including a background term under the peak in the PSD, are then least-squares fitted to the ACF of the previously filtered neutron signal, in order to determine the oscillation frequency and the decay ratio. Our method uses fast Fourier transform techniques with signal segmentation for filtering and ACF estimation. Gliding 'short-term' ACF estimates on a record allow the evaluation of uncertainties. Numerical results are given which have been obtained from neutron data of the recent Forsmark I and Forsmark II NEA benchmark project. Our results are compared with those obtained by other participants in the benchmark project. The present PSI report is an extended version of the publication K. Behringer, D. Hennig 'A novel auto-correlation function method for the determination of the decay ratio in BWR stability studies' (Behringer, Hennig, 2002)

  2. Reactor Neutrinos

    CERN Document Server

    Lasserre, T; Lasserre, Thierry; Sobel, Henry W.

    2005-01-01

    We review the status and the results of reactor neutrino experiments, that toe the cutting edge of neutrino research. Short baseline experiments have provided the measurement of the reactor neutrino spectrum, and are still searching for important phenomena such as the neutrino magnetic moment. They could open the door to the measurement of coherent neutrino scattering in a near future. Middle and long baseline oscillation experiments at Chooz and KamLAND have played a relevant role in neutrino oscillation physics in the last years. It is now widely accepted that a new middle baseline disappearance reactor neutrino experiment with multiple detectors could provide a clean measurement of the last undetermined neutrino mixing angle theta13. We conclude by opening on possible use of neutrinos for Society: NonProliferation of Nuclear materials and Geophysics.

  3. NEUTRONIC REACTORS

    Science.gov (United States)

    Wigner, E.P.; Young, G.J.

    1958-10-14

    A method is presented for loading and unloading rod type fuel elements of a neutronic reactor of the heterogeneous, solld moderator, liquid cooled type. In the embodiment illustrated, the fuel rods are disposed in vertical coolant channels in the reactor core. The fuel rods are loaded and unloaded through the upper openings of the channels which are immersed in the coolant liquid, such as water. Unloading is accomplished by means of a coffer dam assembly having an outer sleeve which is placed in sealing relation around the upper opening. A radiation shield sleeve is disposed in and reciprocable through the coffer dam sleeve. A fuel rod engaging member operates through the axial bore in the radiation shield sleeve to withdraw the fuel rod from its position in the reactor coolant channel into the shield, the shield snd rod then being removed. Loading is accomplished in the reverse procedure.

  4. Efecto de la manipulación del semen criopreservado de bovinos Bos Taurus sobre la integridad espermática

    OpenAIRE

    Norberto Villa-Duque; Claudia Marcela Amaya-Torres; Darwin García-Rojas; Natalia Nieto-Omeara; Natalia Terán-Acuña

    2016-01-01

    En el estudio se evaluó el efecto de descongelar y aplicar semen de bovinos Bos Taurus en 33 ganaderías del Magdalena Medio colombiano, y se estudió in vitro el efecto de la injuria encontrada sobre la integridad de las membranas espermáticas. La información en fincas se recopiló mediante formulario específico, mientras que el estudio in vitro se ejecutó en el laboratorio de Biotecnología Reproductiva Animal del Instituto Universitario de la Paz (Barrancabermeja, Santander). El estudio consis...

  5. Efecto de metanfetamina sobre la actividad de metaloproteinasas y sobre la integridad de la barrera hematoencefálica en ratón: estudios de neurotoxicidad

    OpenAIRE

    Urrutia Elorduy, Andrés

    2013-01-01

    La administración de metanfetamina produce cambios inmediatos sobre la matriz extracelular de la lámina basal que comprometen la integridad de la barrera hematoencefálica (BHE). Estos cambios permiten la extravasación de proteínas plasmáticas al parenquima cerebral. Ambos efectos podrían estar causados por un incremento en la actividad de metaloproteinasas como consecuencia de un aumento en la fosforilación de JNK1/2. Como ocurre en otros modelos de neuroinflamación, alteraciones en la permea...

  6. Corrosion fatigue initiation behaviour of wrought austenitic stainless pipe steels under simulated BWR/HWC and PWR conditions

    Energy Technology Data Exchange (ETDEWEB)

    Leber, H.J.; Ritter, S.; Seifert, H.P [Paul Scherrer Institute, Nuclear Energy and Safety Research Department, Laboratory for Nuclear Materials, 5232 Villigen PSI (Switzerland)

    2011-07-01

    The corrosion fatigue (CF) initiation and short crack growth behavior of different low-carbon and stabilized austenitic stainless steels was characterized under simulated BWR and primary PWR conditions by cyclic fatigue tests with sharply notched fracture mechanics specimens in the temperature range from 70 to 320 C. Environmental reduction of fatigue initiation life was observed in all stainless steels at strain rates {<=} 0.1 %/s in BWR and PWR environment. The stationary short crack CF crack growth rates after crack advances of 50 to 300 {mu}m from the notch-root were in the typical range of corresponding results from tests with long cracks (pre-cracked specimens) and also showed the same system parameter response. The effect of environment on the initiation process ({Delta}a = 10 {mu}m) was relevantly stronger than on the subsequent stationary short crack growth. Both, under BWR/HWC and PWR conditions, a relevant environmental reduction of fatigue initiation life occurred for the combination of temperatures {>=} 100 C, notch strain rates {<=} 0.1 %/s and notch strain amplitudes {>=} 0.3 %. If these conjoint threshold conditions were simultaneously satisfied, the environmental enhancement increased with decreasing strain rate and increasing temperature. Material and water chemistry parameters usually only had a little effect. Sensitization affected the CF behavior under highly oxidizing BWR/NWC conditions only. Preliminary block loading experiments did not reveal significant static load hold period effects on the technical corrosion fatigue initiation life. If the critical requirements were satisfied, the BWR/HWC and PWR environments usually resulted in acceleration of short fatigue crack growth by a factor of 5 to 20 with respect to air. Solution annealed steels showed slightly shorter CF initiation lives, but also lower stationary short CF crack growth rates under BWR/HWC and PWR conditions with low ECPs than under highly oxidizing BWR/NWC conditions. A very

  7. Alternative cooling water flow path for RHR heat exchanger and its effect on containment response during extended station blackout for Chinshan BWR-4 plant

    Energy Technology Data Exchange (ETDEWEB)

    Yuann, Yng-Ruey, E-mail: ryyuann@iner.gov.tw

    2016-04-15

    Highlights: • Motivating alternative RHR heat exchanger tube-side flow path and determining required capacity. • Calculate NSSS and containment response during 24-h SBO for Chinshan BWR-4 plant. • RETRAN and GOTHIC models are developed for NSSS and containment, respectively. • Safety relief valve blowdown flow and energy to drywell are generated by RETRAN. • Analyses are performed with and without reactor depressurization, respectively. - Abstract: The extended Station Blackout (SBO) of 24 h has been analyzed with respect to the containment response, in particular the suppression pool temperature response, for the Chinshan BWR-4 plant of MARK-I containment. The Chinshan plant, owned by Taiwan Power Company, has twin units with rated core thermal power of 1840 MW each. The analysis is aimed at determining the required alternative cooling water flow capacity for the residual heat removal (RHR) heat exchanger when its tube-side sea water cooling flow path is blocked, due to some reason such as earthquake or tsunami, and is switched to the alternative raw water source. Energy will be dissipated to the suppression pool through safety relief valves (SRVs) of the main steam lines during SBO. The RETRAN model is used to calculate the Nuclear Steam Supply System (NSSS) response and generate the SRV blowdown conditions, including SRV pressure, enthalpy, and mass flow rate. These conditions are then used as the time-dependent boundary conditions for the GOTHIC code to calculate the containment pressure and temperature response. The shaft seals of the two recirculation pumps are conservatively assumed to fail due to loss of seal cooling and a total leakage flow rate of 36 gpm to the drywell is included in the GOTHIC model. Based on the given SRV blowdown conditions, the GOTHIC containment calculation is performed several times, through the adjustment of the heat transfer rate of the RHR heat exchanger, until the criterion that the maximum suppression pool temperature

  8. Effects of a hypothetical loss-of-coolant accident on a Mark I Boiling Water Reactor pressure-suppression system

    Energy Technology Data Exchange (ETDEWEB)

    Pitts, J.H.; McCauley, E.W.

    1977-12-22

    A loss-of-coolant accident (LOCA) in a boiling-water-reactor (BWR) power plant has never occurred. However, because this type of accident could be particularly severe, it is used as a principal theoretical basis for design. A series of consistent, versatile, and accurate air-water tests that simulate LOCA conditions has been completed on a /sup 1///sub 5/-scale Mark I BWR pressure-suppression system. Results from these tests are used to quantify the vertical-loading function and to study the associated fluid dynamics phenomena. Detailed histories of vertical loads on the wetwell are shown. In particular, variation of hydrodynamic-generated vertical loads with changes in drywell-pressurization rate, downcomer submergence, and the vent-line loss coefficient are established. Initial drywell overpressure, which partially preclears the downcomers of water, substantially reduces the peak vertical loads. Scaling relationships, developed from dimensional analysis and verified by bench-top experiments, allow the /sup 1///sub 5/-scale results to be applied to a full-scale BWR power plant. This analysis leads to dimensionless groupings that are invariant. These groupings show that, if water is used as the working fluid, the magnitude of the forces in a scaled facility is reduced by the cube of the scale factor and occurs in a time reduced by the square root of the scale factor.

  9. Preliminary Feasibility, Design, and Hazard Analysis of a Boiling Water Test Loop Within the Idaho National Laboratory Advanced Test Reactor National Scientific User Facility

    Energy Technology Data Exchange (ETDEWEB)

    Douglas M. Gerstner

    2009-05-01

    The Advanced Test Reactor (ATR) is a pressurized light-water reactor with a design thermal power of 250 MW. The principal function of the ATR is to provide a high neutron flux for testing reactor fuels and other materials. The ATR and its support facilities are located at the Idaho National Laboratory (INL). A Boiling Water Test Loop (BWTL) is being designed for one of the irradiation test positions within the. The objective of the new loop will be to simulate boiling water reactor (BWR) conditions to support clad corrosion and related reactor material testing. Further it will accommodate power ramping tests of candidate high burn-up fuels and fuel pins/rods for the commercial BWR utilities. The BWTL will be much like the pressurized water loops already in service in 5 of the 9 “flux traps” (region of enhanced neutron flux) in the ATR. The loop coolant will be isolated from the primary coolant system so that the loop’s temperature, pressure, flow rate, and water chemistry can be independently controlled. This paper presents the proposed general design of the in-core and auxiliary BWTL systems; the preliminary results of the neutronics and thermal hydraulics analyses; and the preliminary hazard analysis for safe normal and transient BWTL and ATR operation.

  10. Development of a numerical code for the analysis of the linear stability of the U1 and U2 reactors of the CNLV; Desarrollo de un codigo numerico para el analisis de estabilidad lineal de los reactores de las U1 y U2 de la CNLV

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa P, G.; Estrada P, C.E. [Universidad Autonoma Metropolitana-Iztapalapa, 09000 Mexico D.F. (Mexico); Nunez C, A.; Amador G, R. [Comision Nacional de Seguridad Nuclear y Salvaguardias, Mexico D.F. (Mexico)

    2001-07-01

    The computer code ANESLI-1 developed by the CNSNS and UAM-I, has the main goal of making stability analysis of nuclear reactors of the BWR type, more specifically, the reactors of the U1 and U2 of the CNLV. However it can be used for another kind of applications. Its capacity of real time simulator, allows the prediction of operational transients, and conditions of dynamic steady states. ANESLI-1 was developed under a modular scheme, which allows to extend or/and to improve its scope. The lineal stability analysis predicts the instabilities produced by the wave density phenomenon. (Author)

  11. Heating of reactor pressure vessel bottom head and penetrations in a severe reactor accident; Reaktoripaineastian pohjan ja laepivientien kuumeneminen sydaemen sulamisonnettomuudessa

    Energy Technology Data Exchange (ETDEWEB)

    Ikonen, K. [VTT Energy, Espoo (Finland). Nuclear Energy

    1997-10-01

    The report describes the fundamentals of heat conductivity and convection and numerical methods like finite difference and control volume method for calculation of the thermal history of a reactor pressure vessel bottom head and penetrations. Phase changes from solids to liquids are considered. Time integration is performed by explicit or implicit method. Developed computer codes for thermal conductivity and convection analyses and codes for graphical visualization are described. The codes are applied to two practical cases. They deal with analyses of Swiss CORVIS-experiments and analyses of control rod and instrument penetrations in a BWR bottom head. A model for calculation of effective thermal conductivity of granular corium is developed. The work is also related to EU MVI-project (Core Melt-Pressure Vessel Interactions During a Light Water Reactor Severe Accident), whose coordinator is Prof. B. R. Sehgal at Royal Institute of Technology in Stockholm. (orig.) (11 refs.).

  12. Actinides reduction by recycling in a thermal reactor; Reduccion de actinidos por reciclado en un reactor termico

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez S, J. R.; Martinez C, E.; Balboa L, H., E-mail: ramon.ramirez@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2014-10-15

    This work is directed towards the evaluation of an advanced nuclear fuel cycle in which radioactive actinides could be recycled to remove most of the radioactive material; firstly a production reference of actinides in standard nuclear fuel of uranium at the end of its burning in a BWR reactor is established, after a fuel containing plutonium is modeled to also calculate the actinides production in MOX fuel type. Also it proposes a design of fuel rod containing 6% of actinides in a matrix of uranium from the tails of enrichment, then four standard uranium fuel rods are replaced by actinides rods to evaluate the production and transmutation thereof, the same procedure was performed in the fuel type MOX and the end actinide reduction in the fuel was evaluated. (Author)

  13. Neutronic reactor

    Science.gov (United States)

    Wende, Charles W. J.; Babcock, Dale F.; Menegus, Robert L.

    1983-01-01

    A nuclear reactor includes an active portion with fissionable fuel and neutron moderating material surrounded by neutron reflecting material. A control element in the active portion includes a group of movable rods constructed of neutron-absorbing material. Each rod is movable with respect to the other rods to vary the absorption of neutrons and effect control over neutron flux.

  14. Neutronic reactor

    Energy Technology Data Exchange (ETDEWEB)

    Babcock, D.F.; Menegus, R.L.; Wende, C.W.

    1983-01-04

    A nuclear reactor includes an active portion with fissionable fuel and neutron moderating material surrounded by neutron reflecting material. A control element in the active portion includes a group of movable rods constructed of neutron-absorbing material. Each rod is movable with respect to the other rods to vary the absorption of neutrons and effect control over neutron flux.

  15. Possibilities with OHWC. Development and application of ECP-simulation in Swedish BWRs; Moejligheter med OHWC. Utveckling och tillaempning av ECP-simulering i svenska BWR

    Energy Technology Data Exchange (ETDEWEB)

    Lundgren, K. [ALARA Engineering, Skultuna (Sweden); Wikmark, G. [Advanced Nuclear Technology, Uppsala (Sweden)

    2000-02-01

    Hydrogen injection (HWC) to boiling water reactors has been used for two decades in Sweden, in order to reduce the impact of pipe cracking. The effect of HWC is to establish a sufficiently reducing environment in the systems to protect and hence mitigate the growth of existing stress corrosion cracks. Some disadvantages of HWC have been identified. One is the transitional increase of the dose rate of the main steam lines by up to seven times, another the corrosion release of systems with carbon steel components as a result of the reducing chemistry. In some cases, especially in the USA, an elevated activity build-up has been observed in a few plants in connection to the application of HWC. There is also a fear for increased hydrogen pick-up in fuel cladding and fuel channels by HWC operation. The hydrogen pick-up is already today in many cases limiting for fuel life. The objective of the current work has been to investigate the conditions by application of so called Optimised HWC. This implies a HWC operation with lower hydrogen addition rates than normally used. For this purpose, a computer model in order to simulate the radiolysis chemistry and the ECP (electrochemical corrosion potentials) in BWR systems has been developed. A previously developed radiolysis code, BwrChem, as well as a hydrogen peroxide decomposition code for piping, PEROX, have hence been equipped with ECP calculation modules. The ECP calculation algorithms have been based on fundamental electrochemical theory. The new model has been applied to simulate the radiolysis conditions in a large number of locations in typical BWRs. For the simulation, the external mechanical pump plant Barsebaeck-1 and the internal pump plant Forsmark-1 have been used. A wide range of hydrogen injection rates, down to 0. 1 ppm in the feed water, have been studied. The electrochemical model based on fundamental theory required adequate fundamental parameters. Significant effort has been used to scrutinise and evaluate

  16. Model for the analysis of transitories and stability of a BWR reactor with fuel of thorium; Modelo para el analisis de transitorios y de estabilidad de un reactor BWR con combustible de torio

    Energy Technology Data Exchange (ETDEWEB)

    Nunez C, A. [CNSNS, 03020 Mexico D.F. (Mexico)]. E-mail: anunezc@cnsns.gob.mx; Espinosa P, G. [UAM-I, 09340 Mexico D.F. (Mexico); Francois L, J.L. [Fac. de Ingenieria, UNAM 62550 Jiutepec, Morelos (Mexico)

    2004-07-01

    In this work it is described the thermo hydraulic and neutronic pattern used to simulate the behavior of a nucleus of thorium-uranium under different conditions of operation. The analysed nucleus was designed with base to assemblies that operate under the cover-seed concept. The pattern was proven to conditions of stationary state and transitory state. Here it is only presented the simulation of the one SCRAM manual and it is compared in the behavior of a nucleus with UO{sub 2}. Additionally one carries out an analysis of stability taking into account the four corners that define the area of stability of the map flow-power and to conditions of 100% of flow and 100% of power. The module of stability is based on the pattern of Lahey and Podowsky to estimate the drops of pressure during a perturbation. It is concludes that the behavior of this nucleus is not very different to the one shown by the nuclei loaded with the fuel of UO{sub 2}. (Author)

  17. Algorithms bio-inspired for the pattern obtention of control bars in BWR reactors; Algoritmos bio-inspirados para la obtencion de patrones de barras de control en reactores BWR

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz, J.J.; Perusquia, R.; Montes, J.L. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2003-07-01

    In this work methods based on Genetic Algorithms and Systems based on ant colonies for the obtention of the patterns of control bars of an equilibrium cycle of 18 months for the Laguna Verde nuclear power station are presented. A comparison of obtained results with the methods and with those of design of such equilibrium cycle is presented. As consequence of the study, it was found that the algorithm based on the ant colonies reached to diminish the coast down period (decrease of power at the end of the cycle) in five and half days with respect to the original design what represents an annual saving of $US 100,000. (Author)

  18. DA PROTEÇÃO DA INTEGRIDADE PSICOLÓGICA NO ÂMBITO FAMILIAR BRASILEIRO: NOVAS PERSPECTIVAS DE COMPREENSÃO E INTERVENÇÃO

    Directory of Open Access Journals (Sweden)

    Isadora Vier Machado

    2013-08-01

    Full Text Available As demandas pela tutela jurídica da integridade psicológica, enquanto emanação da personalidade humana, têm crescido no âmbito do direito brasileiro, sobretudo em relação a sujeitos abarcados por estatutos especiais de proteção, como mulheres e crianças. Em virtude da ausência de bibliografia dedicada à análise da temática, a proposta deste artigo consiste em sondar a origem de tais demandas, destacando de que forma têm se apresentado na atualidade e com que respaldo legal. Pretende-se, igualmente, problematizar novas perspectivas críticas nesses contextos, destacando vias alternativas para promover o acesso à justiça destes sujeitos. A metodologia utilizada consistiu em revisão bibliográfica dos campos do Direito, Psicologia, Sociologia e Antropologia. Palavras-chave: Integridade psicológica. Estatutos de proteção. Acesso à justiça.

  19. Crack growth behaviour of low alloy steels for pressure boundary components under transient light water reactor operating conditions (CASTOC)

    Energy Technology Data Exchange (ETDEWEB)

    Foehl, J.; Weissenberg, T. [Materialpruefungsanstalt, Univ. Stuttgart (Germany); Gomez-Briceno, D.; Lapena, J. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT) (Spain); Ernestova, M.; Zamboch, M. [Nuclear Research Inst. (NRI) (Czech Republic); Seifert, H.P.; Ritter, S. [Paul Scherrer Inst. (PSI) (Switzerland); Roth, A.; Devrient, B. [Framatome ANP GmbH (F ANP) (Germany); Ehrnsten, U. [Technical Research Centre of Finland (VTT) (Finland)

    2004-07-01

    The CASTOC project addresses environmentally assisted cracking (EAC) phenomena in low alloy steels used for pressure boundary components in both Western type boiling water reactors (BWR) and Russian type pressurised water reactors (VVER). It comprises the four work packages (WP): inter-laboratory comparison test (WP1); EAC behaviour under static load (WP2), EAC behaviour under cyclic load and load transients (WP3); evaluation of the results with regard to their relevance for components in practice (WP4). The use of sophisticated test facilities and measurement techniques for the on-line detection of crack advances have provided a more detailed understanding of the mechanisms of environmentally assisted cracking and provided quantitative data of crack growth rates as a function of loading events and time, respectively. The effect of several major parameters controlling EAC was investigated with particular emphasis on the transferability of the results to components in service. The obtained crack growth rate data were reflected on literature data and on commonly applied prediction curves as presented in the appropriate Code. At relevant stress intensity factors it could be shown that immediate cessation of growing cracks occurs after changing from cyclic to static load in high purity oxygenated BWR water and oxygen-free VVER water corresponding to steady state operation conditions. Susceptibility to environmentally assisted cracking under static load was observed for a heat affected zone material in oxygenated high purity water and also in base materials during a chloride transient representing BWR water condition below Action Level 1 of the EPRI Water Chemistry Guidelines according to the lectrical conductivity of the water but in the range of Action Level 2 according to the content of chlorides. Time based crack growth was also observed in one Russian type base material in oxygenated VVER water and in one Western type base material in oxygenated high purity BWR

  20. THERMAL EVALUATION OF THE USE OF BWR MOX SNF IN THE MULTI-PURPOSE CANISTER (MPC) WITH ACD DISPOSAL CONTAINER (SCPB: N/A)

    Energy Technology Data Exchange (ETDEWEB)

    T.L. Lotz

    1995-11-13

    This analysis is prepared by the Mined Geologic Disposal System (MGDS) Waste Package Development Department (WPDD) as specified in the Waste Package Implementation Plan (pp. 4-8,4-11,4-24,5-1, and 5-13; Ref. 5.10) and Waste Package Plan (pp. 3-15,3-17, and 3-24; Ref. 5.9). The design data request addressed herein is: (1) Characterize the conceptual 40 BWR Multi-Purpose Canister (MPC) Waste Package (WP) design to show that the design is feasible for use in the MGDS environment when loaded with BWR MOX SNF. (2) Characterize the conceptual 24 BWR Multi-Purpose Canister (MPC) Waste Package (WP) design to show that the design is feasible for use in the MGDS environment when loaded with BWR MOX SNF. The purpose of this analysis is to respond a concern that the long-term disposal thermal issues for the Multi-Purpose Canister (MPC) Subsystem Design, if used with SNF designed for a MOX fuel cycle, do not preclude MPC compatibility with the MGDS. The objective of this analysis is to provide thermal parameter information for the conceptual MPC design with disposal container which is loaded with BWR MOX SNF under nominal MGDS repository conditions. The results are intended to show that the design has a reasonable chance to meet the MGDS design requirements for normal MGDS operation, to provide the required guidance to determining the major design issues for future design efforts, and to show that the BWR MOX SNF loaded MPC performance is similar to an MPC loaded with commercial BWR SNF. Future design efforts will focus on specific MPC vendor designs and BWR MOX SNF designs when they become available.

  1. Study of plutonium disposition using existing GE advanced Boiling Water Reactors

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-01

    The end of the cold war and the resulting dismantlement of nuclear weapons has resulted in the need for the US to dispose of 50 to 100 metric tons of excess of plutonium in a safe and proliferation resistant manner. A number of studies, including the recently released National Academy of Sciences (NAS) study, have recommended conversion of plutonium into spent nuclear fuel with its high radiation barrier as the best means of providing permanent conversion and long-term diversion resistance to this material. The NAS study ``Management and Disposition of Excess Weapons Plutonium identified Light Water Reactor spent fuel as the most readily achievable and proven form for the disposition of excess weapons plutonium. The study also stressed the need for a US disposition program which would enhance the prospects for a timely reciprocal program agreement with Russia. This summary provides the key findings of a GE study where plutonium is converted into Mixed Oxide (MOX) fuel and a typical 1155 MWe GE Boiling Water Reactor (BWR) is utilized to convert the plutonium to spent fuel. A companion study of the Advanced BWR has recently been submitted. The MOX core design work that was conducted for the ABWR enabled GE to apply comparable fuel design concepts and consequently achieve full MOX core loading which optimize plutonium throughput for existing BWRs.

  2. Design of an overmoderated fuel and a full MOX core for plutonium consumption in boiling water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Francois, J.L. E-mail: franmar@prodigy.net.mx; Campo, C.M. del; Hernandez, J

    2002-11-01

    The use of uranium-plutonium mixed oxide fuel (MOX) in light water reactors (LWR) is nowadays a current practice in several countries. Generally 1/3 of the reactor core is loaded with MOX fuel assemblies and the other 2/3 with uranium assemblies. Nevertheless the plutonium utilization could be more effective if the full core could be loaded with MOX fuel. In this paper the design of a boiling water reactor (BWR) core fully loaded with an overmoderated MOX fuel design is investigated. The design of overmoderated BWR MOX fuel assemblies based on a 10x10 lattice are developed, these designs improve the neutron spectrum and the plutonium consumption rate, compared with standard MOX assemblies. In order to increase the moderator to fuel ratio two approaches are followed: in the first approach, 8 or 12 fuel rods are replaced by water rods in the 10x10 lattice; in the second approach, an 11x11 lattice with 24 water rods is designed with an active fuel length very close to the standard MOX assembly. The results of the depletion behavior and the main steady state core parameters are presented. The feasibility of a full core loaded with the 11x11 overmoderated MOX fuel assembly is verified. This design take advantage of the softer spectrum comparable to the 10x10 lattice with 12 water rods but with thermal limits comparable to the standard MOX fuel assembly.

  3. Experimental study for quantative aging evaluation of epoxy liner in BWR nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Na, H. S. [KEPRI, Taejon (Korea, Republic of); Song, Y. C.; Kim, N. Y. [Korea Univ. of Educational Technology, Chonnon (Korea, Republic of)

    2001-10-01

    The purpose of this study is an experimental approach to quantitatively evaluate the aging status of epoxy coating onto containment structure in BWR nuclear power plant. Based on accelerated aging experiment for 64 days, adhesion test was performed to evaluate an physical bonding. To compare with adhesion data, both impedance data by UT and data by thermal gravimetric analysis were obtained during experiment. At almost 50% of adhesion force decrease, it was identified that aging phenamena of epoxy such as pine hole, blistering was discovered. Coating to establish aging status of epoxy, relations among three kinds of different data were analyze. By compatibility of these data, physical aging situation of as-built epoxy coating was figured out. The possibility to develop new methodology of time-dependent aging status on epoxy coating was identified.

  4. Non-local two phase flow momentum transport in S BWR

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa P, G.; Salinas M, L.; Vazquez R, A., E-mail: gepe@xanum.uam.mx [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Area de Ingenieria en Recursos Energeticos, Apdo. Postal 55-535, 09340 Ciudad de Mexico (Mexico)

    2015-09-15

    The non-local momentum transport equations derived in this work contain new terms related with non-local transport effects due to accumulation, convection, diffusion and transport properties for two-phase flow. For instance, they can be applied in the boundary between a two-phase flow and a solid phase, or in the boundary of the transition region of two-phase flows where the local volume averaging equations fail. The S BWR was considered to study the non-local effects on the two-phase flow thermal-hydraulic core performance in steady-state, and the results were compared with the classical local averaging volume conservation equations. (Author)

  5. Modeling of BWR core meltdown accidents - for application in the MELRPI. MOD2 computer code

    Energy Technology Data Exchange (ETDEWEB)

    Koh, B R; Kim, S H; Taleyarkhan, R P; Podowski, M Z; Lahey, Jr, R T

    1985-04-01

    This report summarizes improvements and modifications made in the MELRPI computer code. A major difference between this new, updated version of the code, called MELRPI.MOD2, and the one reported previously, concerns the inclusion of a model for the BWR emergency core cooling systems (ECCS). This model and its computer implementation, the ECCRPI subroutine, account for various emergency injection modes, for both intact and rubblized geometries. Other changes to MELRPI deal with an improved model for canister wall oxidation, rubble bed modeling, and numerical integration of system equations. A complete documentation of the entire MELRPI.MOD2 code is also given, including an input guide, list of subroutines, sample input/output and program listing.

  6. Application of passive auto catalytic recombiner (PAR) for BWR plants in Japan

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, K.; Murano, K. [Tokyo Electric Power Co., Inc. (Japan); Yamanari, S. [Hitachi Cable, Ltd., Tokyo (Japan); Yamamoto, Y. [Toshiba Corp., Yokohama (Japan)

    2001-07-01

    The passive auto-catalytic recombiner (PAR), which can recombine flammable gases such as hydrogen and oxygen with each other to avoid an explosion in case of a loss-of-coolant accident (LOCA), installed in the primary containment vessel does not require a power supply or dynamic equipment, while the existing flammability gas control system (FCS) of most BWRs as an outer loop of the primary containment vessel needs them to make flammable gases circulate through blowers and heaters in the system. PAR offers a number of advantages over existing FCS, such as high reliability, low cost due to much smaller amount of materials needed, good maintainability, good operability in case of a LOCA, and smaller space for installation. An experimental study has been carried out for the purpose of solving the problems of applying PAR to Japanese BWR plants instead of existing FCS, in which we grasped the basic characteristics of PAR. (author)

  7. Feasibility Study of Supercritical Light Water Cooled Fast Reactors for Actinide Burning and Electric Power Production Progress Report for Year 1, Quarter 2 (January - March 2002)

    Energy Technology Data Exchange (ETDEWEB)

    Mac Donald, Philip Elsworth; Buongiorno, Jacopo; Davis, Cliff Bybee; Weaver, Kevan Dean

    2002-03-01

    The use of light water at supercritical pressures as the coolant in a nuclear reactor offers the potential for considerable plant simplification and consequent capital and O&M cost reduction compared with current light water reactor (LWR) designs. Also, given the thermodynamic conditions of the coolant at the core outlet (i.e. temperature and pressure beyond the water critical point), very high thermal efficiencies of the power conversion cycle are possible (i.e. up to about 45%). Because no change of phase occurs in the core, the need for steam separators and dryers as well as for BWR-type re-circulation pumps is eliminated, which, for a given reactor power, results in a substantially shorter reactor vessel and smaller containment building than the current BWRs. Furthermore, in a direct cycle the steam generators are not needed.

  8. Direito à saúde: integridade, diversidade e territorialidade The right to healthcare: integrity, diversity, and territoriality

    Directory of Open Access Journals (Sweden)

    Patrícia Tavares Ribeiro

    2007-12-01

    Full Text Available Este ensaio apresenta algumas questões e desafios para a efetivação do direito universal à saúde no Brasil. Toma como referência resultados de projeto governamental, realizado em 2003, para a ampliação da visão dos problemas relativos ao cuidado à saúde no território nacional, que se baseou em interlocução entre governo e sociedade, complementar às formas já institucionalizadas de participação social no âmbito da gestão setorial. Partindo de uma síntese do complexo cenário internacional em que se desenvolvem as tarefas governamentais para a operacionalização de direitos sociais, destaca, no inventário de problemas identificados, três questões consideradas essenciais para a produção de políticas públicas: a integridade e a dignidade como fundamentos para a organização e regulação das intervenções públicas; o reconhecimento e o respeito à diferença como condição para a realização do direito à saúde; e a territorialização dos problemas e das políticas na produção de respostas às novas realidades. Por fim, elenca algumas indagações que desafiam o governo e a sociedade em suas ações na garantia do direito à saúde, afirmando a oportunidade da gestão governamental avançar na universalização efetiva deste direito pela valorização das temáticas dos direitos humanos e da cidadania.Examining some issues and challenges for ensuring the universal right to healthcare in Brazil, this paper explores the findings of a government project conducted in 2003 to broaden the approach to healthcare problems in Brazil, based on dialogs between government and society that supplement institutionalized approaches to social participation in healthcare management. Starting with an overview of the complex international backdrop against which government actions take place for implementing social rights, this paper highlights three issues among the problems listed that are rated as crucial for drawing up public

  9. MOX fuel assembly and reactor core

    Energy Technology Data Exchange (ETDEWEB)

    Shimada, Hidemitsu; Koyama, Jun-ichi; Aoyama, Motoo

    1998-06-26

    The MOX fuel assembly of the present invention is of a c-lattice type loaded to a BWR type reactor. 74 MOX fuel rods filled with mixed oxides of uranium and plutonium and two water rods disposed to a space equal to that for 7 MOX fuel rods are arranged in 9 x 9 matrix. MOX fuel rods having the lowest enrichment degree are disposed to four corners of the 9 x 9 matrix. The enrichment degree means a ratio of the weight of fission products based on the total weight of fuels. Two MOX fuel rods having the same enrichment degree are arranged in each direction so as to be continuous from the MOX fuel rods at four corners in the direction of the same row and different column and same column and the different row. In addition, among the outermost circumferential portion of the 9 x 9 matrix, MOX fuel rods having a lower enrichment degree next to the MOX fuel rods having the lowest enrichment degree are arranged, each by three to a portion where MOX fuel rods having the lowest enrichment degree are not disposed. (I.N.)

  10. Fast reactor cooled by supercritical light water

    Energy Technology Data Exchange (ETDEWEB)

    Ishiwatari, Yuki; Mukouhara, Tami; Koshizuka, Seiichi; Oka, Yoshiaki [Tokyo Univ., Nuclear Engineering Research Lab., Tokai, Ibaraki (Japan)

    2001-09-01

    This report introduces the result of a feasibility study of a fast reactor cooled by supercritical light water (SCFR) with once-through cooling system. It is characterized by (1) no need of steam separator, recirculation system, or steam generator, (2) 1/7 of core flow rate compared with BWR or PWR, (3) high temperature and high pressure permits small turbine and high efficiency exceeding 44%, (4) structure and operation of major components are already experienced by LWRs or thermal power plants. Modification such as reducing blanket fuels and increasing seed fuels are made to achieve highly economic utilization of Pu and high power (2 GWe). The following restrictions were satisfied. (1) Maximum linear heat rate 39 kW/m, (2) Maximum surface temperature of Inconel cladding 620degC, (3) Negative void reactivity coefficient, (4) Fast neutron irradiation rate at the inner surface of pressure vessel less than 2.0x10{sup 19} n/cm{sup 2}. Thus the high power density of 167 MW/m{sup 3} including blanket is thought to contributes economy. The high conversion is attained to be 0.99 Pu fission residual rate by the outer radius of fuel rod of 0.88 mm. The breeding of 1.034 by Pu fission residual rate can be achieved by using briquette (tube-in-shell) type fuel structure. (K. Tsuchihashi)

  11. OECD - HRP Summer School on Light Water Reactor Structural Materials. August 26th - 30th, 2002

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    In cooperation with the OECD Nuclear Energy Agency (NEA), the Halden Reactor Project organised a Summer School on Light Water Reactor Structural Materials in the period August 26 - 30, 2002. The summer school was primarily intended for people who wanted to become acquainted with materials-related subjects and issues without being experts. It is especially hoped that the summer school served to transfer knowledge to the ''young generation'' in the field of nuclear. Experts from Halden Project member organisations were solicited for the following programme: (1) Overview of The Nuclear Community and Current Issues, (2) Regulatory Framework for Ensuring Structural Integrity, (3) Non-Destructive Testing for Detection of Cracks, (4) Part I - Basics of Radiation and Radiation Damage, (5) Part II - Radiation Effects on Reactor Internal Materials, (6) Water Chemistry and Radiolysis Effects in LWRs, (7) PWR and Fast Breeder Reactor Internals, (8) PWR and Fast Breeder Reactor Internals, (9) Secondary Side Corrosion Cracking of PWR Steam Generator Tubes, (10) BWR Materials and Their Interaction with the Environment, (11) Radiation Damage in Reactor Pressure Vessels.

  12. Analysis of the performance of fuel cells BWR with a single enrichment and radial distribution of enrichments; Analisis del desempeno de celdas combustibles BWR con un solo enriquecimiento y con distribucion radial de enriquecimientos

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, J. A.; Vargas, S.; Alonso, G.; Del Valle, E. [IPN, Escuela Superior de Fisica y Matematicas, Av. IPN s/n, Col. Lindavista, Mexico D. F. 07738 (Mexico); Xolocostli M, J. V. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)]. e-mail: govaj666@hotmail.com

    2008-07-01

    The efficient use of the fuel is one of the objectives in the assemblies design of type BWR. The present tendency in the assemblies design of type BWR is through a radial distribution of enrichments. The present work has like object showing the because of this decision, for what a comparison of the neutronic performance of two fuel cells with the same enrichment average but one of them with radial distribution of enrichment and the other with a single enrichment equal to the average. The cells were analyzed with the CASMO-4 code and the obtained results of the behavior of the neutron flow and the power sustain the because of the radial distribution of enrichments. (Author)

  13. Uncertainty analysis of suppression pool heating during an ATWS in a BWR-5 plant. An application of the CSAU methodology using the BNL engineering plant analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Wulff, W.; Cheng, H.S.; Mallen, A.N. [Brookhaven National Lab., Upton, NY (United States); Johnsen, G.W. [Idaho National Engineering Lab., Idaho Falls, ID (United States); Lellouche, G.S. [Technical Data Services, Chicago, IL (United States)

    1994-03-01

    The uncertainty has been estimated of predicting the peak temperature in the suppression pool of a BWR power plant, which undergoes an NRC-postulated Anticipated Transient Without Scram (ATWS). The ATWS is initiated by recirculation-pump trips, and then leads to power and flow oscillations as they had occurred at the LaSalle-2 Power Station in March of 1988. After limit-cycle oscillations have been established, the turbines are tripped, but without MSIV closure, allowing steam discharge through the turbine bypass into the condenser. Postulated operator actions, namely to lower the reactor vessel pressure and the level elevation in the downcomer, are simulated by a robot model which accounts for operator uncertainty. All balance of plant and control systems modeling uncertainties were part of the statistical uncertainty analysis that was patterned after the Code Scaling, Applicability and Uncertainty (CSAU) evaluation methodology. The analysis showed that the predicted suppression-pool peak temperature of 329.3 K (133{degrees}F) has a 95-percentile uncertainty of 14.4 K (26{degrees}F), and that the size of this uncertainty bracket is dominated by the experimental uncertainty of measuring Safety and Relief Valve mass flow rates under critical-flow conditions. The analysis showed also that the probability of exceeding the suppression-pool temperature limit of 352.6 K (175{degrees}F) is most likely zero (it is estimated as < 5-104). The square root of the sum of the squares of all the computed peak pool temperatures is 350.7 K (171.6{degrees}F).

  14. Fuel performance improvement program. Quarterly/annual progress report, April--September 1977. [BWR; PWR

    Energy Technology Data Exchange (ETDEWEB)

    Crouthamel, C.E. (comp.)

    1977-11-01

    The Fuel Performance Improvement Program has as its objective the identification and demonstration of fuel concepts with improved power ramp performance. The program contains a combination of out-of-reactor studies, in-reactor experiments and in-reactor demonstrations. Fuel concepts initially being considered include annular pellets, cladding internally coated with graphite and packed-particle fuels. The performance capability of each concept will be compared to a reference fuel of contemporary pellet design by irradiations in the Halden Boiling Water Reactor. Fuel design and process development is being completed and fuel rod fabrication will begin for the Halden test rods and for the first series of in-reactor demonstrations. The in-reactor demonstrations are being performed in the Big Rock Point reactor to show that the concepts pose no undue risk to commercial operation.

  15. Burnup calculations using the OREST computer code for uranium dioxide fuel elements of boiling water reactors. Abbrandberechnung mit OREST fuer Urandioxid-Siedewasserreaktor-Brennelemente

    Energy Technology Data Exchange (ETDEWEB)

    Hesse, U.

    1991-01-01

    There are plans to also use plutonium containing fuel elements (mixed oxide fuel) in the BWR type reactors, with a proportion of up to one third of the entire fuel core. The new concept uses complete MOX fuel elements, as are used in the PWR type reactors. The OREST computer code has been designed for burnup calculations in PWRs. The situation in BWRs is different, as in these reactor types, fuel elements are heterogenous in design, and burnup calculations have to take into account the axial variations of the void fraction, so that multi-dimensional effects have to be calculated. The report explains that the one-dimensional OREST code can be enhanced by supplementing calculations, performed with the Monte-Carlo type KENO code in this case, and is thus suitable without restrictions for performing burnup calculations for MOX fuel elements in BWRs. The calculation method and performance is illustrated by the example of a UO{sub 2} fuel element of the Wuergassen reactor. The model calculations predict a relatively high residual activity in the upper part of the fuel element, and a distinct curium buildup in the lower third of the BWR fuel element. (orig./HP).

  16. Nuclear Reactors. Revised.

    Science.gov (United States)

    Hogerton, John F.

    This publication is one of a series of information booklets for the general public published by the United States Atomic Energy Commission. Among the topics discussed are: How Reactors Work; Reactor Design; Research, Teaching, and Materials Testing; Reactors (Research, Teaching and Materials); Production Reactors; Reactors for Electric Power…

  17. Experimental results and analysis of core physics experiments, FUBILA, for high burn-up BWR full MOX cores

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, T.; Kikuchi, S.; Kawashima, K.; Kamimura, K. [Japan Nuclear Energy Safety Organization, 3-17-1, Toranomon, Minato-ku, Tokyo 105-0001 (Japan)

    2006-07-01

    JNES has been performing MOX core physics experiments, FUBILA, in the EOLE critical facility of the CEA Cadarache center with collaboration of a French Consortium (CEA and COGEMA). The experiments have been designed to obtain the core physics data of operating conditions of full MOX BWR cores consisting of high burn up BWR MOX assemblies. The experiments consisting of seven different core configurations started from January 2005 and will be completed by August 2006. Theoretical analysis of the experimental data has been also carried out using a deterministic code, SRAC, and a continuous energy Monte Carlo calculation code, MVP, with major nuclear data libraries, JENDL-3.3, 3.2, ENDF/B-VI and JEFF-3.1 for the first critical core. (authors)

  18. Parametric study of the potential for BWR ECCS strainer blockage due to LOCA generated debris. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Zigler, G.; Brideau, J.; Rao, D.V.; Shaffer, C.; Souto, F.; Thomas, W. [Science and Engineering Associates, Inc., Albuquerque, NM (United States)

    1995-10-01

    This report documents a plant-specific study for a BWR/4 with a Mark I containment that evaluated the potential for LOCA generated debris and the probability of losing long term recirculation capability due ECCS pump suction strainer blockage. The major elements of this study were: (1) acquisition of detailed piping layouts and installed insulation details for a reference BWR; (2) analysis of plant specific piping weld failure probabilities to estimate the LOCA frequency; (3) development of an insulation and other debris generation and drywell transport models for the reference BWR; (4) modeling of debris transport in the suppression pool; (5) development of strainer blockage head loss models for estimating loss of NPSH margin; (6) estimation of core damage frequency attributable to loss of ECCS recirculation capability following a LOCA. Elements 2 through 5 were combined into a computer code, BLOCKAGE 2.3. A point estimate of overall DEGB pipe break frequency (per Rx-year) of 1.59E-04 was calculated for the reference plant, with a corresponding overall ECCS loss of NPSH frequency (per Rx-year) of 1.58E-04. The calculated point estimate of core damage frequency (per Rx-year) due to blockage related accident sequences for the reference BWR ranged from 4.2E-06 to 2.5E-05. The results of this study show that unacceptable strainer blockage and loss of NPSH margin can occur within the first few minutes after ECCS pumps achieve maximum flows when the ECCS strainers are exposed to LOCA generated fibrous debris in the presence of particulates (sludge, paint chips, concrete dust). Generic or unconditional extrapolation of these reference plant calculated results should not be undertaken.

  19. Photocatalytic reactor

    Science.gov (United States)

    Bischoff, Brian L.; Fain, Douglas E.; Stockdale, John A. D.

    1999-01-01

    A photocatalytic reactor for processing selected reactants from a fluid medium comprising at least one permeable photocatalytic membrane having a photocatalytic material. The material forms an area of chemically active sites when illuminated by light at selected wavelengths. When the fluid medium is passed through the illuminated membrane, the reactants are processed at these sites separating the processed fluid from the unprocessed fluid. A light source is provided and a light transmitting means, including an optical fiber, for transmitting light from the light source to the membrane.

  20. VISWAM. A computer code package for thermal reactor physics computations

    Energy Technology Data Exchange (ETDEWEB)

    Jagannathan, V.; Thiyagarajan, T.K.; Ganesan, S.; Jain, R.P.; Pal, U. [Bhabha Atomic Research Centre, Mumbai (India); Karthikeyan, R. [Ecole Polytechnique de Montreal, Montreal, Quebec (Canada)

    2004-07-01

    The nuclear cross section data and reactor physics design methods developed over the past three decades have attained a high degree of reliability for thermal power reactor design and analysis. This is borne out from the analysis of physics commissioning experiments and several reactor-years of operational experience of two types of Indian thermal power reactors, viz. BWRs and PHWRs. Our computational tools were also developed and tested against a large number of IAEA CRP benchmarks on in-core fuel management code package validation for the modern BWR, PWR, VVER and PHWR. Though the computational algorithms are well tested, their mode of use has remained rather obsolete since the codes were developed when the modern high-speed large memory computers were not available. The use of Fortran language limits their potential use for varied applications. We are developing specific Visual Interface Software as the Work Aid support for effective Man-Machine interface (VISWAM). The VISWAM package when fully developed and tested will enable handling the input description of complex fuel assembly and the reactor core geometry with immaculate ease. Selective display of the three dimensional distribution of multi-group fluxes, power distribution and hot spots will provide a good insight into the analysis and also enable inter comparison of different nuclear datasets and methods. Since the new package will be user-friendly, training of requisite human resource for the expanding Indian nuclear power programme will be rendered easier and the gap between an expert and a novice will be greatly reduced. (author)

  1. La integridad del contenido y la autenticidad de origen en la transmisión o puesta a disposición de la factura

    Directory of Open Access Journals (Sweden)

    Juan Jesús Martos García

    2011-10-01

    Full Text Available

    Desde la aprobación de la Directiva 2001/115/CE, la normativa comunitaria regula la factura transmitida y conservada digitalmente, al establecer como requisito genérico para su aceptación que se garantice la integridad del contenido y la autenticidad de origen. La aprobación de la Directiva 2010/45/UE, que tendrá que ser transpuesta antes del 1 de enero del 2013, modifica el marco jurídico de la factura electrónica, al afectar directamente a esta exigencia, lo que sin duda implicará una reforma de nuestra normativa interna.

  2. Hybrid adsorptive membrane reactor

    Energy Technology Data Exchange (ETDEWEB)

    Tsotsis, Theodore T [Huntington Beach, CA; Sahimi, Muhammad [Altadena, CA; Fayyaz-Najafi, Babak [Richmond, CA; Harale, Aadesh [Los Angeles, CA; Park, Byoung-Gi [Yeosu, KR; Liu, Paul K. T. [Lafayette Hill, PA

    2011-03-01

    A hybrid adsorbent-membrane reactor in which the chemical reaction, membrane separation, and product adsorption are coupled. Also disclosed are a dual-reactor apparatus and a process using the reactor or the apparatus.

  3. D and DR Reactors

    Data.gov (United States)

    Federal Laboratory Consortium — The world's second full-scale nuclear reactor was the D Reactor at Hanford which was built in the early 1940's and went operational in December of 1944.D Reactor ran...

  4. Reactor transient

    Energy Technology Data Exchange (ETDEWEB)

    Menegus, R.L.

    1956-05-31

    The authors are planning a calculation to be done on the Univac at the Louviers Building to estimate the effect of xenon transients, a high reactor power. This memorandum outlines the reasons why they prefer to do the work at Louviers rather than at another location, such as N.Y.U. They are to calculate the response of the reactor to a sudden change in position of the half rods. Qualitatively, the response will be a change in the rooftop ratio of the neutron flux. The rooftop ratio may oscillate with high damping, or, instead, it may oscillate for many cycles. It has not been possible for them to determine this response by hand calculation because of the complexity of the problem, and yet it is important for them to be certain that high power operation will not lead us to inherently unstable operation. Therefore they have resorted to machine computation. The system of differential equations that describes the response has seven dependent variables; therefore there are seven equations, each coupled with one or more of the others. The authors have discussed the problem with R.R. Haefner at the plant, and it is his opinion that the IBM 650 cannot adequately handle the system of seven equations because the characteristic time constants vary over a range of about 10{sup 8}. The Univac located at the Louviers Building is said to be satisfactory for this computation.

  5. INFLUÊNCIA DA ESPESSURA E INTEGRIDADE DE COBERTURA PLÁSTICA NA GERMINAÇÃO DE Brassica oleracea var. capitata

    Directory of Open Access Journals (Sweden)

    Amanda Duim Ferreira

    2017-02-01

    Full Text Available Objetivou-se avaliar a influência da espessura e integridade de coberturas plásticas na germinação de sementes de repolho (Brassica oleracea var. capitata cultivadas principalmente na região serrana do Espírito Santo.  O experimento foi conduzido no Laboratório de Tecnologia de Sementes no Campus São Mateus da Universidade Federal do Espírito Santo (UFES, em esquema fatorial 2 x 2, com quatro repetições em delineamento inteiramente casualizado. Os tratamentos consistiram de duas espessuras de cobertura dos recipientes (0,06 mm - plástico fino; 0,10 mm - plástico grosso e a ausência ou presença de furos centralizados na secção superior dos recipientes. As contagens foram feitas do primeiro ao sétimo dia, sendo avaliados os seguintes parâmetros: porcentagem de germinação, índice de velocidade de germinação, tempo médio de germinação, coeficiente de velocidade de germinação e perda de água diária. Verificou-se que não há influência significativa da integridade da cobertura plástica sobre a germinação e é preferível o uso de coberturas plásticas com menor espessura de modo a possibilitar as trocas gasosas.

  6. Study of a fuel assembly for the nuclear reactor of IV generation cooled with supercritical water; Estudio de un ensamble de combustible para el reactor nuclear de generacion IV enfriado con agua supercritica

    Energy Technology Data Exchange (ETDEWEB)

    Barragan M, A.; Martin del Campo M, C.; Francois L, J. L. [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Espinosa P, G., E-mail: albrm29@yahoo.com [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Area de Ingenieria en Recursos Energeticos, Av. San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico D. F. (MX)

    2011-11-15

    In this work a neutron study is presented about a square assembly design of double line of fuel rods, with moderator box to the center of the arrangement, for a nuclear reactor cooled with supercritical water (SCWR). The SCWR reactor was chosen by the characteristics of its design, mainly because is based in light water reactors (PWR and BWR), and the operational experience that has of them allow to use models and similar programs to simulate the fuel and the nucleus of this type of reactors. To develop the necessary models and to carry out the design and analysis of the SCWR reactor, the neutron codes MCNPX and Helios were used. The reason of using both codes, is because the code MCNPX used thoroughly in the neutron simulation of these reactors, it has been our reference code to analyze the results obtained with the Helios code which results are more efficient because its calculation times are minors. In the nucleus design the same parameters for both codes were considered. The results show that the design with Helios is a viable option to simulate these reactors since their values of the neutrons multiplication factor are very similar to those obtained with MCNPX. On the other hand, it could be corroborated that the CASMO-4 code is inadequate to simulate the fuel to the temperature conditions and water pressure in the SCWR. (Author)

  7. Estimation of the activity generated by neutron activation in control rods of a BWR

    Energy Technology Data Exchange (ETDEWEB)

    Rodenas, Jose [Departamento de Ingenieria Quimica y Nuclear, Universidad Politecnica de Valencia, Apartado 22012, E-46071 Valencia (Spain)], E-mail: jrodenas@iqn.upv.es; Gallardo, Sergio; Abarca, Agustin; Juan, Violeta [Departamento de Ingenieria Quimica y Nuclear, Universidad Politecnica de Valencia, Apartado 22012, E-46071 Valencia (Spain)

    2010-04-15

    Control rods are activated by neutron reactions into the reactor. The activation is produced mainly in stainless steel and its impurities. The dose produced by this activity is not important inside the reactor, but it has to be taken into account when the rod is withdrawn from the reactor. Activation reactions produced have been modelled by the MCNP5 code based on the Monte Carlo method. The code gives the number of reactions that can be converted into activity.

  8. Passive gamma analysis of the boiling-water-reactor assemblies

    Science.gov (United States)

    Vo, D.; Favalli, A.; Grogan, B.; Jansson, P.; Liljenfeldt, H.; Mozin, V.; Schwalbach, P.; Sjöland, A.; Tobin, S.; Trellue, H.; Vaccaro, S.

    2016-09-01

    This research focused on the analysis of a set of stationary passive gamma measurements taken on the spent nuclear fuel assemblies from a boiling water reactor (BWR) using pulse height analysis data acquisition. The measurements were performed on 25 different BWR assemblies in 2014 at Sweden's Central Interim Storage Facility for Spent Nuclear Fuel (Clab). This study was performed as part of the Next Generation of Safeguards Initiative-Spent Fuel project to research the application of nondestructive assay (NDA) to spent fuel assemblies. The NGSI-SF team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay (NDA) measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. The final objective of this project is to quantify the capability of several integrated NDA instruments to meet the aforementioned goals using the combined signatures of neutrons, gamma rays, and heat. This report presents a selection of the measured data and summarizes an analysis of the results. Specifically, trends in the count rates measured for spectral lines from the following isotopes were analyzed as a function of the declared burnup and cooling time: 137Cs, 154Eu, 134Cs, and to a lesser extent, 106Ru and 144Ce. From these measured count rates, predictive algorithms were developed to enable the estimation of the burnup and cooling time. Furthermore, these algorithms were benchmarked on a set of assemblies not included in the standard assemblies set used by this research team.

  9. Phenomenology of severe accidents in BWR type reactors. First part; Fenomenologia de accidentes severos en reactores nucleares de agua en ebullicion. Primera parte

    Energy Technology Data Exchange (ETDEWEB)

    Sandoval V, S. [Instituto de Investigaciones Electricas, Gerencia de Energia Nuclear, Av. Reforma 113, Col. Palmira, 62490 Cuernavaca, Morelos (Mexico)

    2003-07-01

    A Severe Accident in a nuclear power plant is a deviation from its normal operating conditions, resulting in substantial damage to the core and, potentially, the release of fission products. Although the occurrence of a Severe Accident on a nuclear power plant is a low probability event, due to the multiple safety systems and strict safety regulations applied since plant design and during operation, Severe Accident Analysis is performed as a safety proactive activity. Nuclear Power Plant Severe Accident Analysis is of great benefit for safety studies, training and accident management, among other applications. This work describes and summarizes some of the most important phenomena in Severe Accident field and briefly illustrates its potential use based on the results of two generic simulations. Equally important and abundant as those here presented, fission product transport and retention phenomena are deferred to a complementary work. (Author)

  10. Nuclear reactor neutron shielding

    Science.gov (United States)

    Speaker, Daniel P; Neeley, Gary W; Inman, James B

    2017-09-12

    A nuclear reactor includes a reactor pressure vessel and a nuclear reactor core comprising fissile material disposed in a lower portion of the reactor pressure vessel. The lower portion of the reactor pressure vessel is disposed in a reactor cavity. An annular neutron stop is located at an elevation above the uppermost elevation of the nuclear reactor core. The annular neutron stop comprises neutron absorbing material filling an annular gap between the reactor pressure vessel and the wall of the reactor cavity. The annular neutron stop may comprise an outer neutron stop ring attached to the wall of the reactor cavity, and an inner neutron stop ring attached to the reactor pressure vessel. An excore instrument guide tube penetrates through the annular neutron stop, and a neutron plug comprising neutron absorbing material is disposed in the tube at the penetration through the neutron stop.

  11. Experimental investigation of mixing of non-isothermal water streams at BWR operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Bergagio, Mattia, E-mail: bergagio@kth.se [AlbaNova University Center, Nuclear Reactor Technology Division, Department of Physics, Royal Institute of Technology, 106 91 Stockholm (Sweden); Anglart, Henryk, E-mail: henryk@kth.se [AlbaNova University Center, Nuclear Reactor Technology Division, Department of Physics, Royal Institute of Technology, 106 91 Stockholm (Sweden); Institute of Heat Engineering, Warsaw University of Technology, 21/25 Nowowiejska Street, 00-665 Warsaw (Poland)

    2017-06-15

    Highlights: • Temperatures are measured in the presence of mixing at BWR operating conditions. • The thermocouple support is moved along a pattern to extend the measurement region. • Uncertainty of 1.58 K for temperatures acquired at 1000 Hz. • Momenta of the hot streams and thermal stratification affect the data examined. • Unconventional spectral analysis is required to further study the data collected. - Abstract: In this experimental investigation, wall surface temperatures have been measured during mixing of three water streams in the annular gap between two coaxial stainless-steel tubes. The inner tube, with an outer diameter of 35 mm and a thickness of 5 mm, holds six K-type, ungrounded thermocouples with a diameter of 0.5 mm, which measured surface temperatures with a sampling rate of either 100 Hz or 1000 Hz. The tube was rotated from 0 to 360° and moved in a range of 387 mm in the axial direction to allow measurements of surface temperatures in the whole mixing region. The outer tube has an inner diameter of 80 mm and a thickness of 10 mm to withstand a water pressure of 9 MPa. A water stream at a temperature of either 333 K or 423 K and a Reynolds number between 1657 and 8410 rose vertically in the annular gap and mixed with two water streams at a temperature of 549 K and a Reynolds number between 3.56 × 10{sup 5} and 7.11 × 10{sup 5}. These two water streams entered the annulus radially on the same axial level, 180° apart. Water pressure was kept at 7.2 MPa. Temperature recordings were performed at five axial and eight azimuthal locations, for each set of boundary conditions. Each recording lasted 120 s to provide reliable data on the variance, intermittency and frequency of the surface temperature time series at hand. Thorough calculations indicate that the uncertainty in the measured temperature is of 1.58 K. The mixing region extends up to 0.2 m downward of the hot inlets. In most cases, measurements indicate non-uniform mixing in the

  12. A bifurcation analysis of boiling water reactor on large domain of parametric spaces

    Science.gov (United States)

    Pandey, Vikas; Singh, Suneet

    2016-09-01

    The boiling water reactors (BWRs) are inherently nonlinear physical system, as any other physical system. The reactivity feedback, which is caused by both moderator density and temperature, allows several effects reflecting the nonlinear behavior of the system. Stability analyses of BWR is done with a simplified, reduced order model, which couples point reactor kinetics with thermal hydraulics of the reactor core. The linear stability analysis of the BWR for steady states shows that at a critical value of bifurcation parameter (i.e. feedback gain), Hopf bifurcation occurs. These stable and unstable domains of parametric spaces cannot be predicted by linear stability analysis because the stability of system does not include only stability of the steady states. The stability of other dynamics of the system such as limit cycles must be included in study of stability. The nonlinear stability analysis (i.e. bifurcation analysis) becomes an indispensable component of stability analysis in this scenario. Hopf bifurcation, which occur with one free parameter, is studied here and it formulates birth of limit cycles. The excitation of these limit cycles makes the system bistable in the case of subcritical bifurcation whereas stable limit cycles continues in an unstable region for supercritical bifurcation. The distinction between subcritical and supercritical Hopf is done by two parameter analysis (i.e. codimension-2 bifurcation). In this scenario, Generalized Hopf bifurcation (GH) takes place, which separates sub and supercritical Hopf bifurcation. The various types of bifurcation such as limit point bifurcation of limit cycle (LPC), period doubling bifurcation of limit cycles (PD) and Neimark-Sacker bifurcation of limit cycles (NS) have been identified with the Floquet multipliers. The LPC manifests itself as the region of bistability whereas chaotic region exist because of cascading of PD. This region of bistability and chaotic solutions are drawn on the various

  13. Formation and deposition of platinum nanoparticles under boiling water reactor conditions

    Science.gov (United States)

    Grundler, Pascal V.; Veleva, Lyubomira; Ritter, Stefan

    2017-10-01

    Stress corrosion cracking (SCC) is a well-known degradation mechanism for components of boiling water reactors (BWRs). Therefore the mitigation of SCC is important for ensuring the integrity of the reactor system. Noble metal chemical application (NMCA) has been developed by General Electric to mitigate SCC and reduce the negative side-effects of hydrogen water chemistry used initially for SCC mitigation. NMCA is now widely applied as an online process (OLNC) during power operation. However, the understanding of the parameters that control the formation and deposition of the noble metal (Pt) particles in a BWR was still incomplete. To fill this knowledge gap, systematic studies on the formation and deposition behaviour of Pt particles in simulated and real BWR environment were performed in the framework of a research project at PSI. The present paper summarizes the most important findings. Experiments in a sophisticated high-temperature water loop revealed that the flow conditions, water chemistry, the Pt injection rate, and the pre-conditioning of the stainless steel surfaces have an impact on the Pt deposition behaviour. Slower Pt injection rates and stoichiometric excess of H2 over O2 produce smaller particles, which may increase the efficiency of the OLNC technique in mitigating SCC. Surfaces with a well-developed oxide layer retain more Pt particles. Furthermore, the pre- and post-OLNC exposure times play an important role for the Pt deposition on specimens exposed at the KKL power plant. Redistribution of Pt in the plant takes place, but most of the Pt apparently does not redeposit on the steel surfaces in the reactor system. Comparison of lab and plant results also demonstrated that plant OLNC applications can be simulated reasonably well on the lab scale.

  14. Stability analysis on natural circulation boiling water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Metz, Peter

    1999-05-01

    The purpose of the study is a stability analysis of the simplified boiling water reactor concept. A fluid dynamics code, DYNOS, was developed and successfully validated against FRIGG and DESIRE data and a stability benchmark on the Ringhals 1 forced circulation BWR. Three simplified desings were considered in the analysis: The SWRIOOO by Siemens and the SBWR and ESBWR from the General Electric Co. For all three design operational characteristics, i.e. power versus flow rate maps, were calculated. The effects which different geometric and operational parameters, such as the riser height, inlet subcooling etc., have on the characteristics have been investigated. Dynamic simulations on the three simplified design revealed the geysering and the natural circulation oscillations modes only. They were, however, only encountered at pressure below 0.6 MPa. Stability maps for all tree simplified BWRs were calculated and plotted. The study concluded that a fast pressurisation of the reactor vessel is necessary to eliminate the possibility of geysering or natural circulation oscillations mode instability. (au) 26 tabs., 88 ills.

  15. Insights for aging management of light water reactor components: Metal containments. Volume 5

    Energy Technology Data Exchange (ETDEWEB)

    Shah, V.N.; Sinha, U.P. [EG and G Idaho, Inc., Idaho Falls, ID (United States); Smith, S.K. [Ogden Environmental and Energy Services, Southfield, MI (United States)

    1994-03-01

    This report evaluates the available technical information and field experience related to management of aging damage to light water reactor metal containments. A generic aging management approach is suggested for the effective and comprehensive aging management of metal containments to ensure their safe operation. The major concern is corrosion of the embedded portion of the containment vessel and detection of this damage. The electromagnetic acoustic transducer and half-cell potential measurement are potential techniques to detect corrosion damage in the embedded portion of the containment vessel. Other corrosion-related concerns include inspection of corrosion damage on the inaccessible side of BWR Mark I and Mark II containment vessels and corrosion of the BWR Mark I torus and emergency core cooling system piping that penetrates the torus, and transgranular stress corrosion cracking of the penetration bellows. Fatigue-related concerns include reduction in the fatigue life (a) of a vessel caused by roughness of the corroded vessel surface and (b) of bellows because of any physical damage. Maintenance of surface coatings and sealant at the metal-concrete interface is the best protection against corrosion of the vessel.

  16. Effects of axial higher mode on core stability of natural circulation BWR

    Energy Technology Data Exchange (ETDEWEB)

    Inada, F.; Furuya, M.; Yasuo, A. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    2003-07-01

    The effect of the chimney on the core stability of natural circulation BWR was investigated using linear stability analysis. The point kinetics model was used for estimating void-reactivity feedback. Drift-flux model was used to evaluate boiling two-phase flow. When chimney was short, the 1st mode was dominant in the case of low power as well as high power. Higher inlet subcooling and higher power could lead to destabilizing effect, and in some case core instability could occur. On the other hand, when chimney was long, it was found that higher harmonics of void fraction perturbation in the chimney could be important. In the case of low power, the 1st mode was less stable, and lower power could lead to the destabilizing effect. In the case of higher power, the higher mode was dominant rather than the 1st mode, and higher inlet subcooling could lead to destabilizing effect, but it was still stable. Sensitivity of stability in the case of long chimney was smaller than that of short chimney, and the instability phenomenon was not generated easily in the case of the long chimney.

  17. AREVA NP burnup credit investigation on irradiated MOX fuel within the REBUS BWR programme

    Energy Technology Data Exchange (ETDEWEB)

    Alander, Alexandra; Misu, Stefan; Timm, Wolf [AREVA, AREVA NP, Erlangen (Germany); Thareau, Sebastien [AREVA, AREVA NP, Paris (France)

    2008-07-01

    The present paper summarizes a criticality and burnup credit investigation carried out using the 2D spectral codes CASMO-4 and APOLLO2-A. Fission rate distributions and multiplication factors, for UOX and MOX configurations, are calculated as well as the reactivity effect caused by burnup on a selection of irradiated MOX fuel assemblies. 3D core criticality calculations were carried out with the Monte Carlo transport code MOCA and the deterministic transport code VARIANT (a nodal code developed by ANL) using CASMO-4 generated cross section libraries. Calculations were compared to experimental data from the critical facility VENUS in the context of the REBUS BWR Programme. The results confirm that the spectral codes CASMO-4 and APOLLO2-A are well suited to calculate fission rates, multiplication factors and reactivity effects. It is also found that the calculated burnup reactivity effect, using CASMO-4 generated cross sections and the best 3D method (MOCA), is underestimated by merely 7% compared to the experimental value, which can mainly be attributed to the simplifications done in order to model the critical configurations with reasonable efforts. (authors)

  18. Analysis of fission product transport under terminated LOCA conditions. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    Gieseke, J.A.; Baybutt, P.; Jordan, H.; Denning, R.S.; Wooton, R.O.

    1977-12-30

    An analytical model was developed to allow preditions of the source term to the containment as dependent on release from the fuel pins and deposition within the primary system. The model was developed into a flexible computer code adaptable to various geometrical arrangements and flow paths. The calculational framework was established in such a way to permit, in principle, the determination of particle and vapor transport and deposition in a general system of control volumes connected by fluid flow in an arbitrary way. This framework requires as input the rate of fission product release to the primary flow, as a function of time for each vapor and particulate species to be considered, and a complete, time dependent, thermal-hydraulic description of the system. TRAP-PWR, TRAP-BWR and TRACK computer codes are specializations, described in detail in the text of this report, of the general framework. The nature of these specializations depends strongly on the degree of detail with which the transporting fluid medium is modeled.

  19. The Physical Mechanism of Core-Wide and Local Instabilities at the Forsmark-1 BWR

    Energy Technology Data Exchange (ETDEWEB)

    Analytis, G. Th. [Paul Scherrer Inst., CH-5232 Villigen PSI (Switzerland). Lab. for Thermohydraulics; Hennig, D. [Paul Scherrer Inst., CH-5232 Villigen PSI (Switzerland). Lab. for Reactor Physics and Systems Engineering; Karlsson, J. K.-H. [Chalmers University of Technology, Gothenburg (Sweden)

    1998-10-01

    During the last 15 years, the problem of BWR instabilities has attracted the attention of a number of researchers. From the theoretical point of view, one would be interested in physically understanding the mechanisms responsible for the in- and out-of-phase core wide power oscillations observed at certain operating points of the power-flow map in different BWRs. From the practical point of view, one must try to avoid these `incidents` since either locally, or globally, the power may substantially exceed the prescribed levels. In this work, we shall use RAMONA3-12 and analyse a rather unusual instability incident at Forsmark-1 in which in addition to the core-wide fundamental spatial mode oscillation, there were local large amplitude power oscillations at different radial positions in the core. We were able to reproduce these unusual experimental findings by assuming that there are large amplitude Density Wave Oscillations (DWOs) in different bundles, induced by the fact that these bundles were not seated properly into the lower fuel support plate. (author) 17 refs., 12 figs.

  20. Identification and assessment of containment and release management strategies for a BWR Mark I containment

    Energy Technology Data Exchange (ETDEWEB)

    Lin, C.C.; Lehner, J.R. (Brookhaven National Lab., Upton, NY (United States))

    1991-09-01

    This report identifies and assesses accident management strategies which could be important for preventing containment failure and/or mitigating the release of fission products during a severe accident in a BWR plant with a Mark 1 type of containment. Based on information available from probabilistic risk assessments and other existing severe accident research, and using simplified containment and release event trees, the report identifies the challenges a Mark 1 containment could face during the course of a severe accident, the mechanisms behind these challenges, and the strategies that could be used to mitigate the challenges. A safety objective tree is developed which provides the connection between the safety objectives, the safety functions, the challenges, and the strategies. The strategies were assessed by applying them to certain severe accident sequence categories which have one or more of the following characteristics: have high probability of core damage or high consequences, lead to a number of challenges, and involve the failure of multiple systems. 59 refs., 55 figs., 27 tabs.

  1. Application of damage function analysis to reactor coolant circuits

    Energy Technology Data Exchange (ETDEWEB)

    MacDonald, D.D. [Center for Electrochemical Science and Technology, Pennsylvania State Univ., University Park, PA (United States)

    2002-07-01

    The application of deterministic models for simulating stress corrosion cracking phenomena in Boiling Water Reactor primary coolant circuits is described. The first generation code, DAMAGE-PREDICTOR, has been used to model the radiolysis of the coolant, to estimate the electrochemical corrosion potential (ECP), and to calculate the crack growth rate (CGR) at fixed state points during reactor operation in about a dozen plants worldwide. This code has been validated in ''double-blind'' comparisons between the calculated and measured hydrogen concentration, oxygen concentration, and ECP in the recirculation system of the Leibstadt BWR in Switzerland, as well as through less formal comparisons with data from other plants. Second generation codes have now been developed, including REMAIN for simulating BWRs with internal coolant pumps and the ALERT series for modeling reactors with external pumps. One of this series, ALERT, yields the integrated damage function (IDF), which is the crack length versus time, on a component-by-component basis for a specified future operating scenario. This code therefore allows one to explore proposed future operating protocols, with the objective of identifying those that are most cost-effective and which minimizes the risk of failure of components in the coolant circuit by stress corrosion cracking. The application of this code is illustrated by exploring the benefits of partial hydrogen water chemistry (HWC) for an actual reactor, in which hydrogen is added to the feedwater over only limited periods during operation. The simulations show that the benefits, in terms of reduction in the IDFs for various components, are sensitive to when HWC was initiated in the plant life and to the length of time over which it is applied. (author)

  2. Reactor process water (PW) piping inspections, 1984--1990

    Energy Technology Data Exchange (ETDEWEB)

    Ehrhart, W.S.; Elder, J.B.; Sprayberry, R.E.; Vande Kamp, R.W.

    1990-12-31

    In July 1983, the NRC ordered the shutdown of five boiling water reactors (BWR`s) because of concerns about reliability of ultrasonic examination for detecting intergranular stress corrosion cracking (IGSCC). These concerns arose because of leaking piping at Niagara Mohawk`s Nine Mile Point which was attributed to IGSCC. The leaks were detected shortly after completion of ultrasonic examinations of the piping. At that time, the Dupont plant manager at Savannah River (SR) directed that investigations be performed to determine if similar problems could exist in SR reactors. Investigation determined that all conditions believed necessary for the initiation and propagation of IGSCC in austenitic stainless steel exist in SR reactor process water (PW) systems. Sensitized, high carbon, austenitic stainless steel, a high purity water system with high levels of dissolved oxygen, and the residual stresses associated with welding during construction combine to provide the necessary conditions. A periodic UT inspection program is now in place to monitor the condition of the reactor PW piping systems. The program is patterned after NRC NUREG 0313, i.e., welds are placed in categories based on their history. Welds in upgraded or replacement piping are examined on a standard schedule (at least every five years) while welds with evidence of IGSCC, evaluated as acceptable for service, are inspected at every extended outage (15 to 18 months). This includes all welds in PW systems three inches in diameter and above. Welds are replaced when MSCC exceeds the replacement criteria of more than twenty percent of pipe circumference of fifty percent of through-wall depth. In the future, we intend to perform flow sizing with automated UT techniques in addition to manual sizing to provide more information for comparison with future examinations.

  3. Reactor process water (PW) piping inspections, 1984--1990

    Energy Technology Data Exchange (ETDEWEB)

    Ehrhart, W.S.; Elder, J.B.; Sprayberry, R.E.; Vande Kamp, R.W.

    1990-01-01

    In July 1983, the NRC ordered the shutdown of five boiling water reactors (BWR's) because of concerns about reliability of ultrasonic examination for detecting intergranular stress corrosion cracking (IGSCC). These concerns arose because of leaking piping at Niagara Mohawk's Nine Mile Point which was attributed to IGSCC. The leaks were detected shortly after completion of ultrasonic examinations of the piping. At that time, the Dupont plant manager at Savannah River (SR) directed that investigations be performed to determine if similar problems could exist in SR reactors. Investigation determined that all conditions believed necessary for the initiation and propagation of IGSCC in austenitic stainless steel exist in SR reactor process water (PW) systems. Sensitized, high carbon, austenitic stainless steel, a high purity water system with high levels of dissolved oxygen, and the residual stresses associated with welding during construction combine to provide the necessary conditions. A periodic UT inspection program is now in place to monitor the condition of the reactor PW piping systems. The program is patterned after NRC NUREG 0313, i.e., welds are placed in categories based on their history. Welds in upgraded or replacement piping are examined on a standard schedule (at least every five years) while welds with evidence of IGSCC, evaluated as acceptable for service, are inspected at every extended outage (15 to 18 months). This includes all welds in PW systems three inches in diameter and above. Welds are replaced when MSCC exceeds the replacement criteria of more than twenty percent of pipe circumference of fifty percent of through-wall depth. In the future, we intend to perform flow sizing with automated UT techniques in addition to manual sizing to provide more information for comparison with future examinations.

  4. Reactor physics analysis for the design of nuclear fuel lattices with burnable poisons

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa-Paredes, G. [Area de Ingenieria en Recursos Energeticos, Universidad Autonoma Metropolitana-Iztapalapa, Av. San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico, D.F. (Mexico); Guzman, Juan R., E-mail: maestro_juan_rafael@hotmail.com [Departamento de Fisica y Matematicas, Instituto Politecnico Nacional, Adolfo Lopez Mateos, San Pedro Zacatenco, 07738 Mexico, D.F. (Mexico)

    2011-12-15

    Highlights: Black-Right-Pointing-Pointer A fuel rod optimization for the coupled bundle-core design in a BWR is developed. Black-Right-Pointing-Pointer An algorithm to minimize the rod power peaking factor is used. Black-Right-Pointing-Pointer The fissile content is divided in two factors. Black-Right-Pointing-Pointer A reactor physics analysis of these factors is performed. Black-Right-Pointing-Pointer The algorithm is applied to a typical BWR fuel lattice. - Abstract: The main goals in nuclear fuel lattice design are: (1) minimizing the rod power peaking factor (PPF) in order that the power level distribution is the most uniform; (2) obtaining a prescribed target value for the multiplication factor (k) at the end of the irradiation in order that the fuel lattice reaches the desired reactivity; and (3) obtaining a prescribed target value for the k at the beginning of the irradiation in order that the reactivity excess is neither a high value (to ease the maneuvering of the control systems) nor a low value (to avoid the penalization of the high cost of the burnable poison content). In this work a simple algorithm to design the burnable poison bearing nuclear fuel lattice is presented. This algorithm is based on a reactor physics analysis. The algorithm is focused on finding the radial distribution of the fuel rods having different fissile and burnable poison contents in order to obtain: (1) an adequate minimum PPF; (2) a prescribed target value of the k at the end of the irradiation; and (3) a prescribed target value of the k at the beginning of the irradiation. This algorithm is based on the factorization of the fissile and burnable poison contents of each fuel rod and on the application of the first-order perturbation theory. The performance of the algorithm is demonstrated with the design of a fuel lattice composed of uranium dioxide (UO{sub 2}) and gadolinium dioxide (Gd{sub 2}O{sub 3}) for boiling water reactors (BWR). This algorithm has been accomplished

  5. A INTEGRIDADE FÍSICA E MORAL DOS PRESOS: A INTERVENÇÃO DO PODER JUDICIÁRIO NA POLÍTICA CARCERÁRIA E A DECISÃO DO SUPREMO TRIBUNAL FEDERAL NO RECURSO EXTRAORDINÁRIO N. 592.581 / PHYSICAL AND MORAL INTEGRITY OF THE PRISONERS: CRITICAL REMARKS

    National Research Council Canada - National Science Library

    Wilson Steinmetz; Cristhian Magnus De Marco

    2015-01-01

    ... na promoção de medidas ou na execução de obras emergenciais em estabelecimentos prisionais para dar efetividade ao postulado da dignidade da pessoa humana e assegurar aos detentos o respeito à sua integridade...

  6. Technical and economic proposal for the extension of the Laguna Verde Nuclear Power plant with an additional nuclear reactor; Propuesta tecnica y economica para la ampliacion de la Central Nucleoelectrica Laguna Verde con un reactor nuclear adicional

    Energy Technology Data Exchange (ETDEWEB)

    Leal C, C.D.; Francois L, J.L. [Facultad de Ingenieria, UNAM, Circuito Interior, C.U. Coyoacan, 04510 Mexico D.F. (Mexico)]. e-mail: carlosdanielleal@yahoo.com.mx

    2006-07-01

    The increment of the human activities in the industrial environments and of generation of electric power, through it burns it of fossil fuels, has brought as consequence an increase in the atmospheric concentrations of the calls greenhouse effect gases and, these in turn, serious repercussions about the environment and the quality of the alive beings life. The recent concern for the environment has provoked that industrialized countries and not industrialized carry out international agreements to mitigate the emission from these gases to the atmosphere. Our country, like part of the international community, not is exempt of this problem for what is necessary that programs begin guided toward the preservation of the environment. As for the electric power generation, it is indispensable to diversify the sources of primary energy; first, to knock down the dependence of the hydrocarbons and, second, to reduce the emission of polluting gases to the atmosphere. In this item, the nucleo electric energy not only has proven to be safe and competitive technical and economically, able to generate big quantities of electric power with a high plant factor and a considerable cost, but rather also, it is one of the energy sources that less pollutants it emits to the atmosphere. The main object of this work is to carry out a technical and economic proposal of the extension of the Laguna Verde Nuclear power plant (CNLV) with a new nuclear reactor of type A BWR (Advanced Boiling Water Reactor), evolutionary design of the BWR technology to which belong the two reactors installed at the moment in the plant, with the purpose of increasing the installed capacity of generation of the CNLV and of the Federal Commission of Electricity (CFE) with foundation in the sustainable development and guaranteeing the protection of the environment by means of the exploitation of a clean and sure technology that counts at the moment with around 12,000 year-reactor of operational experience in more of

  7. Fuel performance improvement program. Quarterly/annual progress report, October 1977--September 1978. [BWR; PWR

    Energy Technology Data Exchange (ETDEWEB)

    Crouthamel, C.E. (comp.)

    1978-10-01

    This quarterly/annual report reviews and summarizes the activities performed in support of the Fuel Performance Improvement Program (FPIP) during Fiscal Year 1978 with emphasis on those activities that transpired during the quarter ending September 30, 1978. Significant progress has been made in achieving the primary objectives of the program, i.e., to demonstrate commercially viable fuel concepts with improved fuel - cladding interaction (FCI) behavior. This includes out-of-reactor experiments to support the fuel concepts being evaluated, initiation of instrumented test rod experiments in the Halden Boiling Water Reactor (HBWR), and fabrication of the first series of demonstration rods for irradiation in the Big Rock Point Reactor (BRPR).

  8. Fracture toughness of irradiated wrought and cast austenitic stainless steels in BWR environment.

    Energy Technology Data Exchange (ETDEWEB)

    Chopra, O. K.; Gruber, E. E.; Shack, W. J.

    2007-01-01

    In light water reactors, austenitic stainless steels (SSs) are used extensively as structural alloys in reactor core internal components because of their high strength, ductility, and fracture toughness. Exposure to high levels of neutron irradiation for extended periods degrades the fracture properties of these steels by changing the material microstructure (e.g., radiation hardening) and microchemistry (e.g., radiation-induced segregation). We look at the results of a study of simulated light-water reactor coolants, material chemistry, and irradiation damage and their effects on the susceptibility to stress-corrosion cracking of various commercially available and laboratory-melted stainless steels.

  9. Fuel Performance Improvement Program. Quarterly progress report, April--June 1977. [BWR, PWR

    Energy Technology Data Exchange (ETDEWEB)

    Rowe, D.S. (comp.)

    1977-07-01

    The Fuel Performance Improvement Program has as its objective the identification and demonstration of fuel concepts with improved power ramp performance. Improved fuels are being sought to allow reduction or elimination of fuel related operating guidelines on nuclear power plants such that the fuel may be power maneuvered within the rates allowed by the system technical specifications. The program contains a combination of out-of-reactor studies, in-reactor experiments and in-reactor demonstrations. Fuel concepts initially being considered include annular-pellets, cladding internally coated with graphite and packed-particle fuels. The performance capability of each concept is being compared to a reference fuel of contemporary pellet design through test reactor experiments.

  10. Studies on the closed-loop digital control of multi-modular reactors

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, J.A. (Massachusetts Inst. of Tech., Cambridge, MA (United States). Nuclear Reactor Lab.); Henry, A.F.; Lanning, D.D.; Meyer, J.E. (Massachusetts Inst. of Tech., Cambridge, MA (United States). Dept. of Nuclear Engineering)

    1992-11-01

    This report describes the theoretical development and the evaluation via both experiment and simulation of digital methods for the closed-loop control of power, temperature, and steam generator level in multi-modular reactors. The major conclusion of the research reported here is that the technology is currently available to automate many aspects of the operation of multi-modular plants. This will in turn minimize the number of required personnel and thus contain both operating and personnel costs, allow each module to be operated at a different power level thereby staggering the times at which refuelings would be needed, and maintain the competitiveness of US industry relative to foreign vendors who are developing and applying advanced control concepts. The technology described in this report is appropriate to the proposed multi-modular reactor designs and to present-generation pressurized water reactors. Its extension to boiling water reactors is possible provided that the commitment is made to create a real-time model of a BWR. The work reported here was performed by the Massachusetts Institute of Technology (MIT) under contract to the Oak Ridge National Laboratory (ORNL) and to the United States Department of Energy (Division of Industry and University Programs, Contract No. DE-FG07-90ER12930.)

  11. Studies on the closed-loop digital control of multi-modular reactors. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, J.A. [Massachusetts Inst. of Tech., Cambridge, MA (United States). Nuclear Reactor Lab.; Henry, A.F.; Lanning, D.D.; Meyer, J.E. [Massachusetts Inst. of Tech., Cambridge, MA (United States). Dept. of Nuclear Engineering

    1992-11-01

    This report describes the theoretical development and the evaluation via both experiment and simulation of digital methods for the closed-loop control of power, temperature, and steam generator level in multi-modular reactors. The major conclusion of the research reported here is that the technology is currently available to automate many aspects of the operation of multi-modular plants. This will in turn minimize the number of required personnel and thus contain both operating and personnel costs, allow each module to be operated at a different power level thereby staggering the times at which refuelings would be needed, and maintain the competitiveness of US industry relative to foreign vendors who are developing and applying advanced control concepts. The technology described in this report is appropriate to the proposed multi-modular reactor designs and to present-generation pressurized water reactors. Its extension to boiling water reactors is possible provided that the commitment is made to create a real-time model of a BWR. The work reported here was performed by the Massachusetts Institute of Technology (MIT) under contract to the Oak Ridge National Laboratory (ORNL) and to the United States Department of Energy (Division of Industry and University Programs, Contract No. DE-FG07-90ER12930.)

  12. Environmentally assisted cracking in light water reactors. Semiannual report, April 1994--September 1994, Volume 19

    Energy Technology Data Exchange (ETDEWEB)

    Chopra, O.K.; Chung, H.M.; Gavenda, D.J. [and others

    1995-09-01

    This report summarizes work performed by Argonne National Laboratory (ANL) on fatigue and environmentally assisted cracking (EAC) in light water reactors from April to September 1994. Topics that have been investigated include (a) fatigue of carbon and low-alloy steel used in piping and reactor pressure vessels, (b) EAC of austenitic stainless steels (SSs) and Alloy 600, and (c) irradiation-assisted stress corrosion cracking (IASCC) of Type 304 SS. Fatigue tests have been conducted on A106-Gr B and A533-Gr B steels in oxygenated water to determine whether a slow strain rate applied during different portions of a tensile-loading cycle are equally effective in decreasing fatigue life. Crack growth data were obtained on fracture-mechanics specimens of SSs and Alloy 600 to investigate EAC in simulated boiling water reactor (BWR) and pressurized water reactor environments at 289{degrees}C. The data were compared with predictions from crack growth correlations developed at ANL for SSs in water and from rates in air from Section XI of the ASME Code. Microchemical changes in high- and commercial-purity Type 304 SS specimens from control-blade absorber tubes and a control-blade sheath from operating BWRs were studied by Auger electron spectroscopy and scanning electron microscopy to determine whether trace impurity elements may contribute to IASCC of these materials.

  13. Integridade da pele prejudicada em idosos: estudo de ocorrência numa comunidade atendida pelo Programa Saúde da Família Integridad de la piel perjudicada en ancianos: estudio de incidencia en una comunidad atendida por el Programa Salud de la Família Impaired skin integrity in the elderly: study of incidence from a community attending a Family Health Program

    Directory of Open Access Journals (Sweden)

    Daniella de Moura Resende

    2006-06-01

    Full Text Available OBJETIVO: esta pesquisa teve como objetivo estudar a ocorrência de integridade da pele prejudicada em idosos de uma comunidade atendida pelo Programa Saúde da Família. MÉTODOS: participaram deste estudo descritivo 40 idosos. A coleta de dados ocorreu de janeiro a junho de 2004 e constou de entrevista e exame clínico. RESULTADOS: A integridade da pele prejudicada foi encontrada em 20 idosos (50%. A característica definidora de maior freqüência foi rompimento da superfície da pele (85%. Os fatores relacionados identificados com freqüência maior ou igual a 50% foram: extremos de idade (100%, fatores imunológicos (100%, alteração do turgor (100%, fatores mecânicos (85%, medicação em uso (50%. CONCLUSÃO: a integridade de pele prejudicada atingiu metade dos sujeitos desta pesquisa, indicando necessidade de intervenções de enfermagem para prevenção e recuperação de lesões, além de promoção da saúde, buscando a integridade tegumentar.OBJETIVO: esta investigación tuvo como objetivo estudiar la ocurrencia de integridad de la piel perjudicada en ancianos de una comunidad atendida por el Programa Salud de la Familia. MÉTODOS: participaron de este estudio descriptivo 40 ancianos. La recolección de los datos ocurrió de enero a junio del 2004 y constó de entrevista y examen clínico. DISCUSIÓN: la integridad de la piel perjudicada fue encontrada en 20 ancianos (50%. La característica que definió la mayor frecuencia fue la ruptura de la superficie de la piel (85%. Los factores relacionados identificados con mayor o igual frecuencia a 50% fueron: extremos de edad (100%, factores inmunológicos (100%, alteración de la turgencia (100%, factores mecánicos (85%, medicación en uso (50%. CONCLUSIÓN: la integridad de la piel perjudicada alcanzó a la mitad de los sujetos de esta investigación, indicando la necesidad de intervenciones de enfermería para la prevención y recuperación de las lesiones, además de la promoción de

  14. Controlling the feedwater flow in a BWR. Examples from Forsmark 2; Regleringen av matarvattenfloedet i en BWR. Med exempel fraan Forsmark 2

    Energy Technology Data Exchange (ETDEWEB)

    Bergdahl, Bengt-Goeran; Oguma, Ritsuo (GSE Power Systems AB, Nykoeping (Sweden))

    2009-03-15

    An investigation of the feedwater controller at Forsmark 2 has been performed. The investigation is based on signal analysis of measurement signals recorded during operation of the plant during different tests. The feedwater controller consists of the water level controller, the flow controller and the condenser balance controller. The overall goal of the feedwater control is to maintain constant water level (level controller) in the reactor and at the same time balance the water levels in the two condensers (condenser balance controller) to avoid that one condenser is full of water while the other one is operated with too low level. There is also a feed forward of the difference between steam flow and feedwater flow (flow controller) for each turbine system with the aim to reduce the fluctuation in reactor water level. The relation in strength between the three controllers is such that the level controller is the strongest followed by the condenser balance controller and finally the flow controller. Tests with trip of the feedwater pump and automatic start of the spare pump in each turbine system indicates a fast reduction in reactor water level that is restored after the transient in the control system. The transient in water level is stable without oscillations. However, it takes about 100 s before the reactor water level is restored. The function of the flow controller has been questioned by the authors. It does not take the action that is expected when a disturbance takes place in the difference between steam and feedwater flow. In addition to this principal weakness there is an offset in the feedwater controller output for feedwater flow 22 that reduces the contribution in flow control that is expected during the introduction of a disturbance. This offset should be adjusted during instrument maintenance of the feedwater controller. The PIP parameters for the level controller are gain factors and time constants. These have been evaluated with the aid of

  15. Recriticality calculation with GENFLO code for the BWR core after steam explosion in the lower head

    Energy Technology Data Exchange (ETDEWEB)

    Miettinen, J. [VTT Processes (Finland)

    2002-12-01

    Recriticality of the partially degraded BWR core has been studied by assuming a severe accident phase during which the fuel rods are still intact but the control rods have experienced extensive damage. Previous NKS and EU projects have studied the same case assuming reflooding by the ECCS system In the present study it was assumed that coolant enters the core due to melt-coolant interaction in the lower plenum. In the first case specified the relocation and fragmentation of the molten control rod metal causes the level swell in the core but no steam explosion. In the second case a steam explosion in the lower head was assumed. I n the first case a prompt recriticality peak can occur, but after the peak no semistable power generation remains. In the second case the consequence of the slug entrance into the core is so violent that the fuel disintegration and melting during the first power peak may occur. After the large power peak water is rapidly pushed back from the core and no semistable power generation maintains. The fuel disintegration studies have been based on a coarse assumption that the acceptable local energy addition into the fresh fuel may be 170 cal/g, but with increasing burn-up it can be as low as 60-70 cal/g. In the level swell variations the maximum energy addition was between these limits, but in most of the steam explosion variations much above these limits. Additional variation of the assumptions related to the neutronics demonstrated that for the converged analysis result some interactions would be useful with respect to the boundary conditions and neutronic options.

  16. Non normal modal analysis of oscillations in boiling water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Suarez-Antola, Roberto, E-mail: roberto.suarez@miem.gub.uy [Ministerio de Industria, Energia y Mineria (MIEM), Montevideo (Uruguay); Flores-Godoy, Jose-Job, E-mail: job.flores@ibero.mx [Universidad Iberoamericana (UIA), Mexico, DF (Mexico). Dept. de Fisica Y Matematicas

    2013-07-01

    The first objective of the present work is to construct a simple reduced order model for BWR stability analysis, combining a two nodes nodal model of the thermal hydraulics with a two modes modal model of the neutronics. Two coupled non-linear integral-differential equations are obtained, in terms of one global (in phase) and one local (out of phase) power amplitude, with direct and cross feedback reactivities given as functions of thermal hydraulics core variables (void fractions and temperatures). The second objective is to apply the effective life time approximation to further simplify the nonlinear equations. Linear approximations for the equations of the amplitudes of the global and regional modes are derived. The linearized equation for the amplitude of the global mode corresponds to a decoupled and damped harmonic oscillator. An analytical closed form formula for the damping coefficient, as a function of the parameters space of the BWR, is obtained. The coefficient changes its sign (with the corresponding modification in the decay ratio) when a stability boundary is crossed. This produces a supercritical Hopf bifurcation, with the steady state power of the reactor as the bifurcation parameter. However, the linearized equation for the amplitude of the regional mode corresponds always to an over-damped and always coupled (with the amplitude of the global mode) harmonic oscillator, for every set of possible values of core parameters (including the steady state power of the reactor) in the framework of the present mathematical model. The equation for the above mentioned over damped linear oscillator is closely connected with a non-normal operator. Due to this connection, there could be a significant transient growth of some solutions of the linear equation. This behavior allows a significant shrinking of the basin of attraction of the equilibrium state. The third objective is to apply the above approach to partially study the stability of the regional mode and

  17. Lessons learned for participation in recent OECD-NEA reactor physics and thermalhydraulic benchmarks

    Energy Technology Data Exchange (ETDEWEB)

    Novog, D.R.; Leung, K.H.; Ball, M. [McMaster Univ., Dept. of Engineering Physics, Hamilton, Ontario (Canada)

    2013-07-01

    Over the last 6 years the OECD-NEA has initiated a series of computational benchmarks in the fields of reactor physics and thermalhydraulics. Within this context McMaster university has been a key contributor and applied several state of the art tools including TSUNAMI, DRAGON, ASSERT, STAR-CCM+, RELAP and TRACE. Considering the tremendous amount of international participation in these benchmarks, there were many lessons of both technical and non-technical that should be shared. This paper presents a summary of the benchmarks, the results and contributions from McMaster, and the authors opinion on the overall conclusions gained from these extensive benchmarks. The benchmarks discussed in this paper include the Uncertainty Analysis in Modelling (UAM), the BWR fine mesh bundle test (BFBT), the PWR Subchannel Boiling Test (PSBT), the MATiS mixing experiment and the IAEA super critical water benchmarks on heat transfer and stability. (author)

  18. Hybrid plasmachemical reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lelevkin, V. M., E-mail: lelevkin44@mail.ru; Smirnova, Yu. G.; Tokarev, A. V. [Kyrgyz-Russian Slavic University (Kyrgyzstan)

    2015-04-15

    A hybrid plasmachemical reactor on the basis of a dielectric barrier discharge in a transformer is developed. The characteristics of the reactor as functions of the dielectric barrier discharge parameters are determined.

  19. Attrition reactor system

    Science.gov (United States)

    Scott, Charles D.; Davison, Brian H.

    1993-01-01

    A reactor vessel for reacting a solid particulate with a liquid reactant has a centrifugal pump in circulatory flow communication with the reactor vessel for providing particulate attrition, resulting in additional fresh surface where the reaction can occur.

  20. Guidebook to nuclear reactors

    Energy Technology Data Exchange (ETDEWEB)

    Nero, A.V. Jr.

    1976-05-01

    A general introduction to reactor physics and theory is followed by descriptions of commercial nuclear reactor types. Future directions for nuclear power are also discussed. The technical level of the material is suitable for laymen.

  1. Response of an ESBWR to an accident like Fukushima; Respuesta de un reactor ESBWR a un accidente tipo Fukushima

    Energy Technology Data Exchange (ETDEWEB)

    Pena G, C. A. [UNAM, Facultad de Ingenieria, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Salazar S, E., E-mail: carlos.pena.guerreo@gmail.com [UNAM, Facultad de Ingenieria, Laboratorio de Analisis en Ingenieria de Reactores Nucleares, 62250 Jiutepec, Morelos (Mexico)

    2014-10-15

    The Fukushima nuclear accident occurred on March 11, 2011 was caused by an earthquake measuring 9.0 on the seismic scale, damaging the nuclear power plant (NPP) containing 6 nuclear reactors of boiling water, some of whom suffered a meltdown due to failure in the cooling systems of these. Electrical wiring was damaged and emergency diesel generators stopped with the arrival of the tsunami, caused by the earthquake. The presence of many critical systems in flood areas provided that a cascade of technological failures occurred, culminating in the complete loss of control over the central and reactors. This had important political consequences and several countries have revised their nuclear programs, considering dangerous and unworkable to the nuclear energy to meet the specific energy needs of each country. However, progress in the design of new reactors raise the possibility of continuing to use nuclear energy for much safer than before. The NPP of Fukushima contained BWR reactors of the first commercial generation designed in the 50. The new passive safety systems raise the idea of simplifying the systems, lowering costs while they are safer systems. New designs meet a these needs in both BWRs and PWRs. In this paper the response of an ESBWR reactor to similar conditions to those suffered by the reactors of Fukushima NPP during the accident is analyzed. In this new reactor of III + generation, the recirculation pumps are removed and emergency cooling systems that can maintain the stable core for several hours without electricity are used. To analyze the responses of this new reactor the simulator with basic principles that IAEA makes available to from Member States was used to better understand and analyze the performance of this type of reactors. (Author)

  2. Validation of the AZTRAN 1.1 code with problems Benchmark of LWR reactors; Validacion del codigo AZTRAN 1.1 con problemas Benchmark de reactores LWR

    Energy Technology Data Exchange (ETDEWEB)

    Vallejo Q, J. A.; Bastida O, G. E.; Francois L, J. L. [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Ciudad Universitaria, 04510 Ciudad de Mexico (Mexico); Xolocostli M, J. V.; Gomez T, A. M., E-mail: amhed.jvq@gmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2016-09-15

    The AZTRAN module is a computational program that is part of the AZTLAN platform (Mexican modeling platform for the analysis and design of nuclear reactors) and that solves the neutron transport equation in 3-dimensional using the discrete ordinates method S{sub N}, steady state and Cartesian geometry. As part of the activities of Working Group 4 (users group) of the AZTLAN project, this work validates the AZTRAN code using the 2002 Yamamoto Benchmark for LWR reactors. For comparison, the commercial code CASMO-4 and the free code Serpent-2 are used; in addition, the results are compared with the data obtained from an article of the PHYSOR 2002 conference. The Benchmark consists of a fuel pin, two UO{sub 2} cells and two other of MOX cells; there is a problem of each cell for each type of reactor PWR and BWR. Although the AZTRAN code is at an early stage of development, the results obtained are encouraging and close to those reported with other internationally accepted codes and methodologies. (Author)

  3. Multivariable analysis of a failure event of pressure regulator in a BWR; Analisis multivariable de un evento de falla del regulador de presion en un BWR

    Energy Technology Data Exchange (ETDEWEB)

    Castillo D, R.; Ortiz V, J. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Calleros M, G. [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Carretera Cardel-Nautla, Km. 43.5, Veracruz (Mexico)], e-mail: rogelio.castillo@inin.gob.mx

    2009-10-15

    The boiling water reactors can experiment three types of instabilities: one caused by the controllers failure of plant, another renowned instability by reactivity and the last knew as thermal hydraulics instability. An event of pressure regulator failure of electro-hydraulic control of Unit 1 of nuclear power plant of Laguna Verde was analyzed, which caused power oscillations that were increasing their magnitude in the time course. The event has been analyzed using the Fourier transformation in short time for time-frequency analysis and for the frequency domain be employment the power spectral density. Both techniques reported a resonance to oscillation frequency of 0.055 Hz in the power spectrum, this frequency is of observed order of magnitude when fail the reactor control systems. However, these analysis did not allow to study the interrelation of event signals. Of the previous studies, were obtained power spectral densities containing picks and valleys related with the dynamic behaviour of reactor, which includes the control systems performance. For a pick or present valley to a specific frequency in the power spectrum for one of previous variables, can determine the influence of other variables on the pick or valley by relative contribution of power. This method was established in a developed program of name Noise, which uses a multivariable autoregressive model to obtain the autoregressive coefficients, and starting from them the relative contribution of power is determined. Basically two important results were obtained, the first is related with the influence of feed water flow on the other variables to the frequency of 0.055 Hz, the second is related with the instability by reactivity and confirms that this way was not excited during the event. (Author)

  4. Data report of BWR post-CHF tests. Transient core thermal-hydraulic test program. Contract research

    Energy Technology Data Exchange (ETDEWEB)

    Iguchi, Tadashi; Itoh, Hideo; Kiuchi, Toshio; Watanabe, Hironori; Kimura, Mamoru; Anoda, Yoshinari [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-03-01

    JAERI has been performing transient core thermal-hydraulic test program. In the program, authors performed BWR/ABWR DBE simulation tests with a test facility, which can simulate BWR/ABWR transients. The test facility has a 4 x 4 bundle core simulator with 15-rod heaters and one non-heated rod. Through the tests, authors quantified the thermal safety margin for core cooling. In order to quantify the thermal safety margin, authors collected experimental data on post-CHF. The data are essential for the evaluation of clad temperature transient when core heat-up occurs during DBEs. In comparison with previous post-CHF tests, present experiments were performed in much wider experimental condition, covering high clad temperature, low to high pressure and low to high mass flux. Further, data at wider elevation (lower to higher elevation of core) were obtained in the present experiments, which make possible to discuss the effect of axial position on thermal-hydraulics, while previous works usually discuss the thermal-hydraulics at the position where the first heat-up occurs. This data report describes test procedure, test condition and major experimental data of post-CHF tests. (author)

  5. NUCLEAR REACTOR CONTROL SYSTEM

    Science.gov (United States)

    Epler, E.P.; Hanauer, S.H.; Oakes, L.C.

    1959-11-01

    A control system is described for a nuclear reactor using enriched uranium fuel of the type of the swimming pool and other heterogeneous nuclear reactors. Circuits are included for automatically removing and inserting the control rods during the course of normal operation. Appropriate safety circuits close down the nuclear reactor in the event of emergency.

  6. Application of the Monte Carlo method to estimate doses due to neutron activation of different materials in a nuclear reactor

    Science.gov (United States)

    Ródenas, José

    2017-11-01

    All materials exposed to some neutron flux can be activated independently of the kind of the neutron source. In this study, a nuclear reactor has been considered as neutron source. In particular, the activation of control rods in a BWR is studied to obtain the doses produced around the storage pool for irradiated fuel of the plant when control rods are withdrawn from the reactor and installed into this pool. It is very important to calculate these doses because they can affect to plant workers in the area. The MCNP code based on the Monte Carlo method has been applied to simulate activation reactions produced in the control rods inserted into the reactor. Obtained activities are introduced as input into another MC model to estimate doses produced by them. The comparison of simulation results with experimental measurements allows the validation of developed models. The developed MC models have been also applied to simulate the activation of other materials, such as components of a stainless steel sample introduced into a training reactors. These models, once validated, can be applied to other situations and materials where a neutron flux can be found, not only nuclear reactors. For instance, activation analysis with an Am-Be source, neutrography techniques in both medical applications and non-destructive analysis of materials, civil engineering applications using a Troxler, analysis of materials in decommissioning of nuclear power plants, etc.

  7. Developing Fully Coupled Dynamical Reactor Core Isolation System Models in RELAP-7 for Extended Station Black-Out Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Haihua Zhao; Ling Zou; Hongbin Zhang; David Andrs; Richard Martineau

    2014-04-01

    The reactor core isolation cooling (RCIC) system in a boiling water reactor (BWR) provides makeup water to the reactor vessel for core cooling when the main steam lines are isolated and the normal supply of water to the reactor vessel is lost. It was one of the very few safety systems still available during the Fukushima Daiichi accidents after the tsunamis hit the plants and the system successfully delayed the core meltdown for a few days for unit 2 & 3. Therefore, detailed models for RCIC system components are indispensable to understand extended station black-out accidents (SBO) for BWRs. As part of the effort to develop the new generation reactor system safety analysis code RELAP-7, major components to simulate the RCIC system have been developed. This paper describes the models for those components such as turbine, pump, and wet well. Selected individual component test simulations and a simplified SBO simulation up to but before core damage is presented. The successful implementation of the simplified RCIC and wet well models paves the way to further improve the models for safety analysis by including more detailed physical processes in the near future.

  8. A STRONGLY COUPLED REACTOR CORE ISOLATION COOLING SYSTEM MODEL FOR EXTENDED STATION BLACK-OUT ANALYSES

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Haihua [Idaho National Laboratory; Zhang, Hongbin [Idaho National Laboratory; Zou, Ling [Idaho National Laboratory; Martineau, Richard Charles [Idaho National Laboratory

    2015-03-01

    The reactor core isolation cooling (RCIC) system in a boiling water reactor (BWR) provides makeup cooling water to the reactor pressure vessel (RPV) when the main steam lines are isolated and the normal supply of water to the reactor vessel is lost. The RCIC system operates independently of AC power, service air, or external cooling water systems. The only required external energy source is from the battery to maintain the logic circuits to control the opening and/or closure of valves in the RCIC systems in order to control the RPV water level by shutting down the RCIC pump to avoid overfilling the RPV and flooding the steam line to the RCIC turbine. It is generally considered in almost all the existing station black-out accidents (SBO) analyses that loss of the DC power would result in overfilling the steam line and allowing liquid water to flow into the RCIC turbine, where it is assumed that the turbine would then be disabled. This behavior, however, was not observed in the Fukushima Daiichi accidents, where the Unit 2 RCIC functioned without DC power for nearly three days. Therefore, more detailed mechanistic models for RCIC system components are needed to understand the extended SBO for BWRs. As part of the effort to develop the next generation reactor system safety analysis code RELAP-7, we have developed a strongly coupled RCIC system model, which consists of a turbine model, a pump model, a check valve model, a wet well model, and their coupling models. Unlike the traditional SBO simulations where mass flow rates are typically given in the input file through time dependent functions, the real mass flow rates through the turbine and the pump loops in our model are dynamically calculated according to conservation laws and turbine/pump operation curves. A simplified SBO demonstration RELAP-7 model with this RCIC model has been successfully developed. The demonstration model includes the major components for the primary system of a BWR, as well as the safety

  9. Nuclear reactor overflow line

    Science.gov (United States)

    Severson, Wayne J.

    1976-01-01

    The overflow line for the reactor vessel of a liquid-metal-cooled nuclear reactor includes means for establishing and maintaining a continuous bleed flow of coolant amounting to 5 to 10% of the total coolant flow through the overflow line to prevent thermal shock to the overflow line when the reactor is restarted following a trip. Preferably a tube is disposed concentrically just inside the overflow line extending from a point just inside the reactor vessel to an overflow tank and a suction line is provided opening into the body of liquid metal in the reactor vessel and into the annulus between the overflow line and the inner tube.

  10. Light water reactor safety

    CERN Document Server

    Pershagen, B

    2013-01-01

    This book describes the principles and practices of reactor safety as applied to the design, regulation and operation of light water reactors, combining a historical approach with an up-to-date account of the safety, technology and operating experience of both pressurized water reactors and boiling water reactors. The introductory chapters set out the basic facts upon which the safety of light water reactors depend. The central section is devoted to the methods and results of safety analysis. The accidents at Three Mile Island and Chernobyl are reviewed and their implications for light wate

  11. Nuclear reactor physics

    CERN Document Server

    Stacey, Weston M

    2010-01-01

    Nuclear reactor physics is the core discipline of nuclear engineering. Nuclear reactors now account for a significant portion of the electrical power generated worldwide, and new power reactors with improved fuel cycles are being developed. At the same time, the past few decades have seen an ever-increasing number of industrial, medical, military, and research applications for nuclear reactors. The second edition of this successful comprehensive textbook and reference on basic and advanced nuclear reactor physics has been completely updated, revised and enlarged to include the latest developme

  12. Definition of loss-of-coolant accident radiation source. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    1978-02-01

    Meaningful qualification testing of nuclear reactor components requires a knowledge of the radiation fields expected in a loss-of-coolant accident (LOCA). The overall objective of this program is to define the LOCA source terms and compare these with the output of various simulators employed for radiation qualification testing. The basis for comparison will be the energy deposition in a model reactor component. The results of the calculations are presented and some interpretation of the results given. The energy release rates and spectra were validated by comparison with other calculations using different codes since experimental data appropriate to these calculations do not exist.

  13. Spinning fluids reactor

    Science.gov (United States)

    Miller, Jan D; Hupka, Jan; Aranowski, Robert

    2012-11-20

    A spinning fluids reactor, includes a reactor body (24) having a circular cross-section and a fluid contactor screen (26) within the reactor body (24). The fluid contactor screen (26) having a plurality of apertures and a circular cross-section concentric with the reactor body (24) for a length thus forming an inner volume (28) bound by the fluid contactor screen (26) and an outer volume (30) bound by the reactor body (24) and the fluid contactor screen (26). A primary inlet (20) can be operatively connected to the reactor body (24) and can be configured to produce flow-through first spinning flow of a first fluid within the inner volume (28). A secondary inlet (22) can similarly be operatively connected to the reactor body (24) and can be configured to produce a second flow of a second fluid within the outer volume (30) which is optionally spinning.

  14. Thermal limits validation of gamma thermometer power adaption in CFE Laguna Verde 2 reactor core

    Energy Technology Data Exchange (ETDEWEB)

    Cuevas V, G.; Banfield, J. [GE-Hitachi Nuclear Energy Americas LLC, Global Nuclear Fuel, Americas LLC, 3901 Castle Hayne Road, Wilmingtonm, North Carolina (United States); Avila N, A., E-mail: Gabriel.Cuevas-Vivas@ge.com [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Carretera Cardel-Nautla Km 42.5, Alto Lucero, Veracruz (Mexico)

    2016-09-15

    This paper presents the status of GEH work on Gamma Thermometer (GT) validation using the signals of the instruments installed in the Laguna Verde Unit 2 reactor core. The long-standing technical collaboration between Comision Federal de Electricidad (CFE), Global Nuclear Fuel - Americas LLC (GNF) and GE-Hitachi Nuclear Energy Americas LLC (GEH) is moving forward with solid steps to a final implementation of GTs in a nuclear reactor core. Each GT is integrated into a slightly modified Local Power Range Monitor (LPRM) assembly. Six instrumentation strings are equipped with two gamma field detectors for a total of twenty-four bundles whose calculated powers are adapted to the instrumentation readings in addition to their use as calibration instruments for LPRMs. Since November 2007, the six GT instrumentation strings have been operable with almost no degradation by the strong neutron and gamma fluxes in the Laguna Verde Unit 2 reactor core. In this paper, the thermal limits, Critical Power Ratio (CPR) and maximum Linear Heat Generation Rate (LHGR), of bundles directly monitored by either Traverse In-core Probes (TIPs) or GTs are used to establish validation results that confirm the viability of TIP system replacement with automatic fixed in-core probes (AFIPs, GTs, in a Boiling Water Reactor. The new GNF steady-state reactor core simulator AETNA02 is used to obtain power and exposure distribution. Using this code with an updated methodology for GT power adaption, a reduced value of the GT interpolation uncertainty is obtained that is fed into the LHGR calculation. This new method achieves margin recovery for the adapted thermal limits for use in the Economic Simplified Boiling Water Reactor (ESBWR) or any other BWR in the future that employs a GT based AFIP system for local power measurements. (Author)

  15. Control Rod Drive Mechanism Installed in the Internal of Reactor Pressure Vessel

    Energy Technology Data Exchange (ETDEWEB)

    Choi, M. H.; Choi, S.; Park, J. S.; Lee, J. S.; Kim, D. O.; Hur, N. S.; Hur, H.; Yu, J. Y

    2008-09-15

    This report describes the review results and important technologies related to the in-vessel type control rod drive mechanism. Generally, most of the CRDMs used in the PWR are attached outside of the reactor pressure vessel, and the pernetration of the vessel head can not avoid. However, in-vessel type CRDMs, which are installed inside the reactor vessel, can eliminate the possibility of rod ejection accidents and the penetration of the vessel head, and provide a compact design of the reactor vessel and containment. There are two kinds of in-vessel type CRDM concerning the driving force-driven by a driving motor and by a hydraulic force. Motor driven CRDMs have been mainly investigated in Japan(MRX, IMR, DRX, next generation BWR etc.), and developed the key components such as a canned motor, an integrated rod position indicator, a separating ball-nut and a ball bearing that can operate under the water conditions of a high temperature and pressure. The concept of hydraulically driven CRDMs have been first reported by KWU and Siemens for KWU 200 reactor, and Argentina(CAREM) and China(NHR-5, NHR-200) have been developed the internal CRDM with the piston and cylinder of slightly different geometries. These systems are driven by the hydraulic force which is produced by pumps outside of the reactor vessel and transmitted through a pipe penetrating the reactor vessel, and needs complicated control and piping systems including pumps, valves and pipes etc.. IRIS has been recently decided the internal CRDMs as the reference design, and an analytical and experimental investigations of the hydraulic drive concept are performed by POLIMI in Italy. Also, a small French company, MP98 has been developed a new type of control rods, called 'liquid control rods', where reactivity is controlled by the movement of a liquid absorber in a manometer type device.

  16. Simulation of a nuclear accident by an academic simulator of a VVER-1000 reactor; Simulacion de un accidente nuclear, mediante un simulador academico de un reactor VVER-1000

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez G, L. [UNAM, Facultad de Ingenieria, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Salazar S, E., E-mail: laurahg42@gmail.com [UNAM, Facultad de Ingenieria, Laboratorio de Analisis en Ingenieria de Reactores Nucleares, 62250 Jiutepec, Morelos (Mexico)

    2014-10-15

    This work is planned to simulate a scenario in which the same conditions that caused the accident at the Fukushima Daichi nuclear power plant are present, using a simulator of a nuclear power plant with VVER-1000 reactor, a different type of technology to the NPP where the accident occurred, which used BWR reactors. The software where it will take place the simulation was created and distributed by the IAEA for academic purposes, which contains the essential systems that characterize this type of NPP. The simulator has tools for the analysis of the characteristic phenomena of a VVER-1000 reactor in the different systems together and planned training tasks. This makes possible to identify the function of each component and how connects to other systems, thus facilitating the visualization of possible failures and the consequences that they have on the general behavior of the reactor. To program the conditions in the simulator, is necessary to know and synthesize a series of events occurred in Fukushima in 2011 and the realized maneuvers to reduce the effects of the system failures. Being different technologies interpretation of the changes that would suffer the VVER systems in the scenario in question will be developed. The Fukushima accident was characterized by the power loss of regular supply and emergency of the cooling systems which resulted in an increase in reactor temperature and subsequent fusion of their nuclei. Is interesting to reproduce this type of failure in a VVER, and extrapolate the lack of power supply in the systems that comprise, as well as pumping systems for cooling, has a pressure regulating system which involves more variables in the balance of the system. (Author)

  17. EVOLUCIÓN DE LA INTEGRIDAD ESTRUCTURAL DE ECOSISTEMAS LÓTICOS DEL PIEDEMONTE LLANERO FRENTE A LA INTERVENCIÓN ANTRÓPICA

    Directory of Open Access Journals (Sweden)

    Guillermo BRICEÑO VANEGAS

    2015-01-01

    Full Text Available Entre los años 1993 y 2007 se determinó la evolución de la integridad ecológica de dos corrientes del piedemonte llanero del Meta, los caños Mateguadua y Caibe en proximidades a los municipios de Restrepo y Cumaral. Los parámetros analizados fueron la evolución del paisaje, el comportamiento de las variables fisicoquímicas, la calidad y oferta de hábitats acuáticos y la organización estructural de las comunidades ícticas. El paisaje experimentó un deterioro severo durante el periodo analizado de muestreo por causa de la deforestación del bosque de galería en ambas corrientes. El lavado y la erosión de los suelos aportaron una carga considerable de sólidos a las corrientes, produjeron sedimentación en el lecho de ambos caños, alteraron los patrones de profundidad y redujeron drásticamente la heterogeneidad espacial de los hábitats acuáticos. La estructura de la comunidad íctica experimentó alteraciones en respuesta al deterioro ambiental, como por ejemplo el progresivo reemplazamiento de especies insectívoras por especies algívoras y fitófagas y la dominancia de poblaciones de Hemigrammus barrigonae, especie que prosperó gracias al avance paulatino de colonias de microalgas y macrófitas en al agua por causa de la fragmentación del bosque de galería.

  18. Thermomechanical evaluation of BWR fuel elements for procedures of preconditioned with FEMAXI-V; Evaluacion termomecanica de elementos combustible BWR para procedimientos de preacondicionado con FEMAXI-V

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez L, H.; Lucatero, M.A.; Ortiz V, J. [ININ, Carretera Mexico-Toluca Km 36.5, La Marquesa, Estado de Mexico (Mexico)]. e-mail: hhl@nuclear.inin.mx

    2006-07-01

    The limitations in the burnt of the nuclear fuel usually are fixed by the one limit in the efforts to that undergo them the components of a nuclear fuel assembly. The limits defined its provide the direction to the fuel designer to reduce to the minimum the fuel failure during the operation, and they also prevent against some thermomechanical phenomena that could happen during the evolution of transitory events. Particularly, a limit value of LHGR is fixed to consider those physical phenomena that could lead to the interaction of the pellet-shirt (Pellet Cladding Interaction, PCI). This limit value it is related directly with an PCI limit that can be fixed based on experimental tests of power ramps. This way, to avoid to violate the PCI limit, the conditioning procedures of the fuel are still required for fuel elements with and without barrier. Those simulation procedures of the power ramp are carried out for the reactor operator during the starting maneuvers or of power increase like preventive measure of possible consequences in the thermomechanical behavior of the fuel. In this work, the thermomechanical behavior of two different types of fuel rods of the boiling water reactor is analyzed during the pursuit of the procedures of fuel preconditioning. Five diverse preconditioning calculations were carried out, each one with three diverse linear ramps of power increments. The starting point of the ramps was taken of the data of the cycle 8 of the unit 1 of the Laguna Verde Nucleo electric Central. The superior limit superior of the ramps it was the threshold of the lineal power in which a fuel failure could be presented by PCI, in function of the fuel burnt. The analysis was carried out with the FEMAXI-V code. (Author)

  19. Information to be requested from the NSSS vendor for fuel management capability for BWR

    Energy Technology Data Exchange (ETDEWEB)

    Minguez, E.; Esteban, A.; Gomez, M.; Leira, G.; Martinez, R.; Serrano, J.

    1975-07-01

    A set of the nuclear, thermal-hydraulic, and mechanical parameters necessary according to the design of BWRs, is listed. This parameters are necessary to perform the fuel elements management and design, and it must be supplied by the Reactor Manufacturer to the Utility. (Author) 18 refs.

  20. Neutron fluxes in test reactors

    Energy Technology Data Exchange (ETDEWEB)

    Youinou, Gilles Jean-Michel [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2017-01-01

    Communicate the fact that high-power water-cooled test reactors such as the Advanced Test Reactor (ATR), the High Flux Isotope Reactor (HFIR) or the Jules Horowitz Reactor (JHR) cannot provide fast flux levels as high as sodium-cooled fast test reactors. The memo first presents some basics physics considerations about neutron fluxes in test reactors and then uses ATR, HFIR and JHR as an illustration of the performance of modern high-power water-cooled test reactors.

  1. HORIZONTAL BOILING REACTOR SYSTEM

    Science.gov (United States)

    Treshow, M.

    1958-11-18

    Reactors of the boiling water type are described wherein water serves both as the moderator and coolant. The reactor system consists essentially of a horizontal pressure vessel divided into two compartments by a weir, a thermal neutronic reactor core having vertical coolant passages and designed to use water as a moderator-coolant posltioned in one compartment, means for removing live steam from the other compartment and means for conveying feed-water and water from the steam compartment to the reactor compartment. The system further includes auxiliary apparatus to utilize the steam for driving a turbine and returning the condensate to the feed-water inlet of the reactor. The entire system is designed so that the reactor is self-regulating and has self-limiting power and self-limiting pressure features.

  2. Fast Spectrum Reactors

    CERN Document Server

    Todd, Donald; Tsvetkov, Pavel

    2012-01-01

    Fast Spectrum Reactors presents a detailed overview of world-wide technology contributing to the development of fast spectrum reactors. With a unique focus on the capabilities of fast spectrum reactors to address nuclear waste transmutation issues, in addition to the well-known capabilities of breeding new fuel, this volume describes how fast spectrum reactors contribute to the wide application of nuclear power systems to serve the global nuclear renaissance while minimizing nuclear proliferation concerns. Readers will find an introduction to the sustainable development of nuclear energy and the role of fast reactors, in addition to an economic analysis of nuclear reactors. A section devoted to neutronics offers the current trends in nuclear design, such as performance parameters and the optimization of advanced power systems. The latest findings on fuel management, partitioning and transmutation include the physics, efficiency and strategies of transmutation, homogeneous and heterogeneous recycling, in addit...

  3. Safety and licensing issues that are being addressed by the Power Burst Facility test programs. [PWR; BWR

    Energy Technology Data Exchange (ETDEWEB)

    McCardell, R.K.; MacDonald, P.E.

    1980-01-01

    This paper presents an overview of the results of the experimental program being conducted in the Power Burst Facility and the relationship of these results to certain safety and licensing issues. The safety issues that were addressed by the Power-Cooling-Mismatch, Reactivity Initiated Accident, and Loss of Coolant Accident tests, which comprised the original test program in the Power Burst Facility, are discussed. The resolution of these safety issues based on the results of the thirty-six tests performed to date, is presented. The future resolution of safety issues identified in the new Power Burst Facility test program which consists of tests which simulate BWR and PWR operational transients, anticipated transients without scram, and severe fuel damage accidents, is described.

  4. THERMAL NEUTRONIC REACTOR

    Science.gov (United States)

    Spinrad, B.I.

    1960-01-12

    A novel thermal reactor was designed in which a first reflector formed from a high atomic weight, nonmoderating material is disposed immediately adjacent to the reactor core. A second reflector composed of a moderating material is disposed outwardly of the first reflector. The advantage of this novel reflector arrangement is that the first reflector provides a high slow neutron flux in the second reflector, where irradiation experiments may be conducted with a small effect on reactor reactivity.

  5. Estimation of fast neutron fluence in steel specimens type Laguna Verde in TRIGA Mark III reactor; Estimacion de la fluencia de neutrones rapidos en probetas de acero tipo Laguna Verde en el reactor Triga Mark III

    Energy Technology Data Exchange (ETDEWEB)

    Galicia A, J.; Francois L, J. L. [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Ciudad Universitaria, 04510 Ciudad de Mexico (Mexico); Aguilar H, F., E-mail: blink19871@hotmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2015-09-15

    The main purpose of this work is to obtain the fluence of fast neutrons recorded within four specimens of carbon steel, similar to the material having the vessels of the BWR reactors of the nuclear power plant of Laguna Verde when subjected to neutron flux in a experimental facility of the TRIGA Mark III reactor, calculating an irradiation time to age the material so accelerated. For the calculation of the neutron flux in the specimens was used the Monte Carlo code MCNP5. In an initial stage, three sheets of natural molybdenum and molybdenum trioxide (MoO{sub 3}) were incorporated into a model developed of the TRIGA reactor operating at 1 M Wth, to calculate the resulting activity by setting a certain time of irradiation. The results obtained were compared with experimentally measured activities in these same materials to validate the calculated neutron flux in the model used. Subsequently, the fast neutron flux received by the steel specimens to incorporate them in the experimental facility E-16 of the reactor core model operating at nominal maximum power in steady-state was calculated, already from these calculations the irradiation time required was obtained for values of the neutron flux in the range of 10{sup 18} n/cm{sup 2}, which is estimated for the case of Laguna Verde after 32 years of effective operation at maximum power. (Author)

  6. Integridade e externalização: estudo exploratório em uma amostra de estudantes de psicologia Integrity and externalizing: an exploratory study in a sample of psychology students

    Directory of Open Access Journals (Sweden)

    Viviane Oliveira Baumgartl

    2009-12-01

    Full Text Available Testes psicológicos que avaliam o construto integridade são amplamente utilizados nos Estados Unidos com o objetivo de tentar prever a ocorrência de comportamentos contraprodutivos no ambiente de trabalho, tais como atrasos, roubos e abuso de substâncias químicas. O presente estudo buscou investigar a relação entre integridade e externalização (fator de personalidade ligado à disposição em apresentar problemas ligados ao controle de impulsos, tendo em vista o fato dos dois construtos estarem relacionados conceitualmente. Participaram da pesquisa 209 estudantes de psicologia, provenientes de duas Universidades de Minas Gerais (pública e particular, que foram submetidos à aplicação de uma versão traduzida e adaptada do teste de integridade Personnel Reaction Blank (PRB e do Inventário de Externalização-100. A investigação da relação entre integridade e externalização indicou uma associação moderada e negativa (r=-0,59 entre os escores globais dos dois instrumentos. Houve, portanto, uma associação entre maior manifestação de comportamentos dignos e honestos e menor manifestação de comportamentos antissociais impulsivos. Sugestões de estudos futuros são apontadas.Psychological tests that assess the construct integrity are widely used in the United States with the aim of preventing the occurrence of counter-productive behaviors in the workplace, such as delays, thefts and chemical substances abuse. The present study aimed to investigate the relation between integrity and externalizing (personality factor that reflects proneness to an array of impulse-control problems considering that both constructs are conceptually related. A total of 209 Psychology students from two universities in Minas Gerais participated in the present study. They were submitted to a translated and adapted version of the test of integrity Personnel Reaction Blank (PRB and to the Externalization Inventory-100. The investigation of the relation

  7. Remote Reactor Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Bernstein, Adam [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Dazeley, Steve [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Dobie, Doug [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Marleau, Peter [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Brennan, Jim [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gerling, Mark [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sumner, Matthew [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sweany, Melinda [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-10-21

    The overall goal of the WATCHMAN project is to experimentally demonstrate the potential of water Cerenkov antineutrino detectors as a tool for remote monitoring of nuclear reactors. In particular, the project seeks to field a large prototype gadolinium-doped, water-based antineutrino detector to demonstrate sensitivity to a power reactor at ~10 kilometer standoff using a kiloton scale detector. The technology under development, when fully realized at large scale, could provide remote near-real-time information about reactor existence and operational status for small operating nuclear reactors out to distances of many hundreds of kilometers.

  8. Development of reactor graphite

    Science.gov (United States)

    Haag, G.; Mindermann, D.; Wilhelmi, G.; Persicke, H.; Ulsamer, W.

    1990-04-01

    The German graphite development programme for High Temperature Reactors has been based on the assumption that reactor graphite for core components with lifetime fluences of up to 4 × 10 22 neutrons per cm 2 (EDN) at 400°C can be manufactured from regular pitch coke. The use of secondary coke and vibrational moulding techniques have allowed production of materials with very small anisotropy, high strength, and high purity which are the most important properties of reactor graphite. A variety of graphite grades has been tested in fast neutron irradiation experiments. The results show that suitable graphites for modern High Temperature Reactors with spherical fuel elements are available.

  9. Oscillatory flow chemical reactors

    National Research Council Canada - National Science Library

    Slavnić Danijela S; Bugarski Branko M; Nikačević Nikola M

    2014-01-01

    .... However, the reactions of interests for the mentioned industry sectors are often slow, thus continuous tubular reactors would be impractically long for flow regimes which provide sufficient heat...

  10. Membrane reactors at Degussa.

    Science.gov (United States)

    Wöltinger, Jens; Karau, Andreas; Leuchtenberger, Wolfgang; Drauz, Karlheinz

    2005-01-01

    The review covers the development of membrane reactor technologies at Degussa for the synthesis of fine chemicals. The operation of fed-batch or continuous biocatalytic processes in the enzyme membrane reactor (EMR) is well established at Degussa. Degussa has experience of running EMRs from laboratory gram scale up to a production scale of several hundreds of tons per year. The transfer of the enzyme membrane reactor from biocatalysis to chemical catalysis in the chemzyme membrane reactor (CMR) is discussed. Various homogeneous catalysts have been investigated in the CMR, and the scope and limitation of this new technique is discussed.

  11. Pressurizing new reactors

    Energy Technology Data Exchange (ETDEWEB)

    Neill, J.S.

    1956-01-30

    The Technical Division was asked recently to consider designs for new reactors that would add 8000 MW capacity to the Savannah River Plant. One modification of the existing SRP design that would enable a higher power rating, and therefore require fewer new reactors, is an increase in the maximum pressure in the D{sub 2}O system. The existing reactors at SRP are designed for a maximum pressure in the gas plenum of only 5 psig. Higher pressures enable higher D{sub 2} temperatures and higher sheath temperatures without local boiling or burnout. The requirements in reactor cooling facilities at any given power level would therefore be reduced by pressurizing.

  12. HOMOGENEOUS NUCLEAR POWER REACTOR

    Science.gov (United States)

    King, L.D.P.

    1959-09-01

    A homogeneous nuclear power reactor utilizing forced circulation of the liquid fuel is described. The reactor does not require fuel handling outside of the reactor vessel during any normal operation including complete shutdown to room temperature, the reactor being selfregulating under extreme operating conditions and controlled by the thermal expansion of the liquid fuel. The liquid fuel utilized is a uranium, phosphoric acid, and water solution which requires no gus exhaust system or independent gas recombining system, thereby eliminating the handling of radioiytic gas.

  13. Detecting long-range correlation with detrended fluctuation analysis: Application to BWR stability

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa-Paredes, Gilberto [Departamento de Ingenieria de Procesos e Hidraulica, Universidad Autonoma Metropolitana-Iztapalapa, Apartado Postal 55-534, Mexico, DF 09340 (Mexico)]. E-mail: gepe@xanum.uam.mx; Alvarez-Ramirez, Jose [Departamento de Ingenieria de Procesos e Hidraulica, Universidad Autonoma Metropolitana-Iztapalapa, Apartado Postal 55-534, Mexico, DF 09340 (Mexico); Vazquez, Alejandro [Departamento de Ingenieria de Procesos e Hidraulica, Universidad Autonoma Metropolitana-Iztapalapa, Apartado Postal 55-534, Mexico, DF 09340 (Mexico)

    2006-11-15

    The aim of this paper is to explore the application of detrended fluctuation analysis (DFA) to study boiling water reactor stability. DFA is a scaling method commonly used for detecting long-range correlations in non-stationary time series. This method is based on the random walk theory and was applied to neutronic power signal of Forsmark stability benchmark. Our results shows that the scaling properties breakdown during unstable oscillations.

  14. Crack growth rates and fracture toughness of irradiated austenitic stainless steels in BWR environments.

    Energy Technology Data Exchange (ETDEWEB)

    Chopra, O. K.; Shack, W. J.

    2008-01-21

    In light water reactors, austenitic stainless steels (SSs) are used extensively as structural alloys in reactor core internal components because of their high strength, ductility, and fracture toughness. However, exposure to high levels of neutron irradiation for extended periods degrades the fracture properties of these steels by changing the material microstructure (e.g., radiation hardening) and microchemistry (e.g., radiation-induced segregation). Experimental data are presented on the fracture toughness and crack growth rates (CGRs) of wrought and cast austenitic SSs, including weld heat-affected-zone materials, that were irradiated to fluence levels as high as {approx} 2x 10{sup 21} n/cm{sup 2} (E > 1 MeV) ({approx} 3 dpa) in a light water reactor at 288-300 C. The results are compared with the data available in the literature. The effects of material composition, irradiation dose, and water chemistry on CGRs under cyclic and stress corrosion cracking conditions were determined. A superposition model was used to represent the cyclic CGRs of austenitic SSs. The effects of neutron irradiation on the fracture toughness of these steels, as well as the effects of material and irradiation conditions and test temperature, have been evaluated. A fracture toughness trend curve that bounds the existing data has been defined. The synergistic effects of thermal and radiation embrittlement of cast austenitic SS internal components have also been evaluated.

  15. A Compilation of Boiling Water Reactor Operational Experience for the United Kingdom's Office for Nuclear Regulation's Advanced Boiling Water Reactor Generic Design Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Wheeler, Timothy A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Liao, Huafei [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-12-01

    United States nuclear power plant Licensee Event Reports (LERs), submitted to the United States Nuclear Regulatory Commission (NRC) under law as required by 10 CFR 50.72 and 50.73 were evaluated for reliance to the United Kingdom’s Health and Safety Executive – Office for Nuclear Regulation’s (ONR) general design assessment of the Advanced Boiling Water Reactor (ABWR) design. An NRC compendium of LERs, compiled by Idaho National Laboratory over the time period January 1, 2000 through March 31, 2014, were sorted by BWR safety system and sorted into two categories: those events leading to a SCRAM, and those events which constituted a safety system failure. The LERs were then evaluated as to the relevance of the operational experience to the ABWR design.

  16. Technical specifications, Hanford production reactors

    Energy Technology Data Exchange (ETDEWEB)

    Gilbert, W.D. [comp.

    1962-06-25

    These technical specifications are applicable to the eight operating production reactor facilities, B, C, D, DR, F, H, KE, and KW. Covered are operating and performance restrictions and administrative procedures. Areas covered by the operating and performance restrictions are reactivity, reactor control and safety elements, power level, temperature and heat flux, reactor fuel loadings, reactor coolant systems, reactor confinement, test facilities, code compliance, and reactor scram set points. Administrative procedures include process control procedures, training programs, audits and inspections, and reports and records.

  17. Reactor Materials Research

    Energy Technology Data Exchange (ETDEWEB)

    Van Walle, E

    2001-04-01

    The activities of the Reactor Materials Research Department of the Belgian Nuclear Research Centre SCK-CEN in 2000 are summarised. The programmes within the department are focussed on studies concerning (1) fusion, in particular mechanical testing; (2) Irradiation Assisted Stress Corrosion Cracking (IASCC); (3) nuclear fuel; and (4) Reactor Pressure Vessel Steel (RPVS)

  18. Space Nuclear Reactor Engineering

    Energy Technology Data Exchange (ETDEWEB)

    Poston, David Irvin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-06

    We needed to find a space reactor concept that could be attractive to NASA for flight and proven with a rapid turnaround, low-cost nuclear test. Heat-pipe-cooled reactors coupled to Stirling engines long identified as the easiest path to near-term, low-cost concept.

  19. REFLECTOR FOR NEUTRONIC REACTORS

    Science.gov (United States)

    Fraas, A.P.

    1963-08-01

    A reflector for nuclear reactors that comprises an assembly of closely packed graphite rods disposed with their major axes substantially perpendicular to the interface between the reactor core and the reflector is described. Each graphite rod is round in transverse cross section at (at least) its interface end and is provided, at that end, with a coaxial, inwardly tapering hole. (AEC)

  20. Mirror reactor surface study

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, A. L.; Damm, C. C.; Futch, A. H.; Hiskes, J. R.; Meisenheimer, R. G.; Moir, R. W.; Simonen, T. C.; Stallard, B. W.; Taylor, C. E.

    1976-09-01

    A general survey is presented of surface-related phenomena associated with the following mirror reactor elements: plasma first wall, ion sources, neutral beams, director converters, vacuum systems, and plasma diagnostics. A discussion of surface phenomena in possible abnormal reactor operation is included. Several studies which appear to merit immediate attention and which are essential to the development of mirror reactors are abstracted from the list of recommended areas for surface work. The appendix contains a discussion of the fundamentals of particle/surface interactions. The interactions surveyed are backscattering, thermal desorption, sputtering, diffusion, particle ranges in solids, and surface spectroscopic methods. A bibliography lists references in a number of categories pertinent to mirror reactors. Several complete published and unpublished reports on surface aspects of current mirror plasma experiments and reactor developments are also included.

  1. Nuclear reactor design

    CERN Document Server

    2014-01-01

    This book focuses on core design and methods for design and analysis. It is based on advances made in nuclear power utilization and computational methods over the past 40 years, covering core design of boiling water reactors and pressurized water reactors, as well as fast reactors and high-temperature gas-cooled reactors. The objectives of this book are to help graduate and advanced undergraduate students to understand core design and analysis, and to serve as a background reference for engineers actively working in light water reactors. Methodologies for core design and analysis, together with physical descriptions, are emphasized. The book also covers coupled thermal hydraulic core calculations, plant dynamics, and safety analysis, allowing readers to understand core design in relation to plant control and safety.

  2. Status of French reactors

    Energy Technology Data Exchange (ETDEWEB)

    Ballagny, A. [Commissariat a l`Energie Atomique, Saclay (France)

    1997-08-01

    The status of French reactors is reviewed. The ORPHEE and RHF reactors can not be operated with a LEU fuel which would be limited to 4.8 g U/cm{sup 3}. The OSIRIS reactor has already been converted to LEU. It will use U{sub 3}Si{sub 2} as soon as its present stock of UO{sub 2} fuel is used up, at the end of 1994. The decision to close down the SILOE reactor in the near future is not propitious for the start of a conversion process. The REX 2000 reactor, which is expected to be commissioned in 2005, will use LEU (except if the fast neutrons core option is selected). Concerning the end of the HEU fuel cycle, the best option is reprocessing followed by conversion of the reprocessed uranium to LEU.

  3. Environmentally assisted cracking in light water reactors.

    Energy Technology Data Exchange (ETDEWEB)

    Chopra, O. K.; Chung, H. M.; Clark, R. W.; Gruber, E. E.; Shack, W. J.; Soppet, W. K.; Strain, R. V.

    2007-11-06

    This report summarizes work performed by Argonne National Laboratory on fatigue and environmentally assisted cracking (EAC) in light water reactors (LWRs) from January to December 2002. Topics that have been investigated include: (a) environmental effects on fatigue crack initiation in carbon and low-alloy steels and austenitic stainless steels (SSs), (b) irradiation-assisted stress corrosion cracking (IASCC) of austenitic SSs in BWRs, (c) evaluation of causes and mechanisms of irradiation-assisted cracking of austenitic SS in PWRs, and (d) cracking in Ni-alloys and welds. A critical review of the ASME Code fatigue design margins and an assessment of the conservation in the current choice of design margins are presented. The existing fatigue {var_epsilon}-N data have been evaluated to define the effects of key material, loading, and environmental parameters on the fatigue lives of carbon and low-alloy steels and austenitic SSs. Experimental data are presented on the effects of surface roughness on fatigue crack initiation in these materials in air and LWR environments. Crack growth tests were performed in BWR environments on SSs irradiated to 0.9 and 2.0 x 10{sup 21} n x cm{sup -2}. The crack growth rates (CGRs) of the irradiated steels are a factor of {approx}5 higher than the disposition curve proposed in NUREG-0313 for thermally sensitized materials. The CGRs decreased by an order of magnitude in low-dissolved oxygen (DO) environments. Slow-strain-rate tensile (SSRT) tests were conducted in high-purity 289 C water on steels irradiated to {approx}3 dpa. The bulk S content correlated well with the susceptibility to intergranular SCC in 289 C water. The IASCC susceptibility of SSs that contain >0.003 wt. % S increased drastically. bend tests in inert environments at 23 C were conducted on broken pieces of SSRT specimens and on unirradiated specimens of the same materials after hydrogen charging. The results of the tests and a review of other data in the literature

  4. Integridade ambiental de corpos d’água: degradação ambiental, funções ecossistêmicas e perda de serviços ecossistêmicos no baixo São Francisco.

    Directory of Open Access Journals (Sweden)

    Rafael Rodrigues Freire

    2014-08-01

    Full Text Available Os estudos de definição de hidrogramas ambientais, necessários para amenizar os impactos causados por barramentos, buscam alternativas para conciliar usos e sustentabilidade de recursos naturais, visando à conservação ambiental e a redução de conflitos de usuários. Um dos mecanismos para determinação da vazão ambiental é a metodologia Building Block que é baseada em um processo de interação entre cientistas e comunidades de usos tradicionais, e considera a população extrativista e ribeirinha como uma das fontes de informação para o conhecimento do rio, por estar em contato diário com ele e por depender diretamente do seu estado saudável e da diversidade de sua biota. Esta metodologia prevê, na sua fase inicial, a avaliação do estado da integridade do habitat, a fim de conhecer preliminarmente um retrato dos efeitos das alterações dos processos ambientais, informações que auxiliam na definição do planejamento dos estudos sucessivos e na individuação das localidades mais representativas, selecionadas como pontos amostrais da pesquisa. Contudo, a avaliação da Integridade do Habitat proposta no BBM leva em consideração exclusivamente aspectos ecológicos, mais especificamente de habitat, não considerando os aspectos socioambientais relacionados aos diversos usos de recursos naturais. Isso constitui uma contradição em relação aos objetivos intrínsecos ao conceito de vazão ambiental. Por esta razão, este trabalho teve como objetivo propor um aprimoramento da metodologia BBM, na sua fase inicial de planejamento dos estudos, agregando à ferramenta de definição da integridade do habitat um componente de avaliação socioambiental. Este componente socioambiental foi incorporado através da avaliação da perda de disponibilidade dos serviços ecossistêmicos percebida pelas comunidades extrativistas ribeirinhas. A partir dos relatos de informantes-chaves foram definidos oitos indicadores quali

  5. Coupled vibrations of a structure and fluid excited by pressure shocks. [BWR

    Energy Technology Data Exchange (ETDEWEB)

    Arros, J.

    1979-12-01

    The dynamic behavior of an axisymmetric boiling water reactor suppression pool structure and the embedded water under the excitation of the pressure waves from collapsing steam bubbles was studied with a finite element model. The structure was analyzed with thin shell elements. The fluid volume is divided into isoparametric quadrilateral toroidal elements with pressure as the nodal parameter. A water source element was utilized to model the pressure shock excitation. Nonaxisymmetric pressure loads and vibration modes were expressed as a Fourier series in the circumferential coordinate. The system of equations for the structure and fluid was integrated in time using the central difference scheme.

  6. Stability analysis of the high performance light water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Ortega Gomez, Tino

    2009-03-15

    In the Generation IV international advanced nuclear reactor development program, the High Performance Light Water Reactor (HPLWR) is one of the most promising candidates. Important features are its inherently high thermodynamic efficiency (of approximately 45 %) and the ability to use existing supercritical water technology which previously has been developed and deployed for fossil fired power plants. Within a HPLWR core, the fluid experiences a drastic change in thermal and transport properties such as density, dynamic viscosity, specific heat and thermal conductivity, as the supercritical water is heated from 280 C to 500 C. The density change substantially exceeds that in a Boiling Water Reactor (i.e., HPLWR: density changes from 780 kg/m{sup 3} to 90 kg/m{sup 3}; BWR: density changes from 750 kg/m{sup 3} to 198 kg/m3). Due to this density change, the HPLWR can be - under certain operation parameters - susceptible to various thermal-hydraulic flow instabilities, which have to be avoided. In this thesis a stability analysis for the HPLWR is presented. This analysis is based on analytical considerations and numerical results, which were obtained by a computer code developed by the author. The heat-up stages of the HPLWR three-pass core are identified in respect to the relevant flow instability phenomena. The modeling approach successfully used for BWR stability analysis is extended to supercritical pressure operation conditions. In particular, a one-dimensional equation set representing the coolant flow of HPLWR fuel assemblies has been implemented in a commercial software named COMSOL to perform steady-state, time-dependent, and modal analyses. An investigation of important static instabilities (i.e., Ledinegg instabilities, flow maldistribution) and Pressure Drop Oscillations (PDO) have been carried out and none were found under operation conditions of the HPLWR. Three types of Density Wave Oscillation (DWO) modes have been studied: the single channel DWO, the

  7. Nuclear reactor control column

    Science.gov (United States)

    Bachovchin, Dennis M.

    1982-01-01

    The nuclear reactor control column comprises a column disposed within the nuclear reactor core having a variable cross-section hollow channel and containing balls whose vertical location is determined by the flow of the reactor coolant through the column. The control column is divided into three basic sections wherein each of the sections has a different cross-sectional area. The uppermost section of the control column has the greatest cross-sectional area, the intermediate section of the control column has the smallest cross-sectional area, and the lowermost section of the control column has the intermediate cross-sectional area. In this manner, the area of the uppermost section can be established such that when the reactor coolant is flowing under normal conditions therethrough, the absorber balls will be lifted and suspended in a fluidized bed manner in the upper section. However, when the reactor coolant flow falls below a predetermined value, the absorber balls will fall through the intermediate section and into the lowermost section, thereby reducing the reactivity of the reactor core and shutting down the reactor.

  8. Reactor Safety Research Programs

    Energy Technology Data Exchange (ETDEWEB)

    Edler, S. K.

    1981-07-01

    This document summarizes the work performed by Pacific Northwest Laboratory (PNL) from January 1 through March 31, 1981, for the Division of Reactor Safety Research within the U.S. Nuclear Regulatory Commission (NRC). Evaluations of nondestructive examination (NDE) techniques and instrumentation are reported; areas of investigation include demonstrating the feasibility of determining the strength of structural graphite, evaluating the feasibility of detecting and analyzing flaw growth in reactor pressure boundary systems, examining NDE reliability and probabilistic fracture mechanics, and assessing the integrity of pressurized water reactor (PWR) steam generator tubes where service-induced degradation has been indicated. Experimental data and analytical models are being provided to aid in decision-making regarding pipeto- pipe impacts following postulated breaks in high-energy fluid system piping. Core thermal models are being developed to provide better digital codes to compute the behavior of full-scale reactor systems under postulated accident conditions. Fuel assemblies and analytical support are being provided for experimental programs at other facilities. These programs include loss-ofcoolant accident (LOCA) simulation tests at the NRU reactor, Chalk River, Canada; fuel rod deformation, severe fuel damage, and postaccide