The Evaluation of Triphenyl Phosphate as a Flame Retardant Additive to Improve the Safety of Lithium-Ion Battery Electrolytes

Science.gov (United States)

Smart, M. C.; Krause, F. C.; Hwang, C.; West, W. C.; Soler, J.; Prakash, G. K. S.; Ratnakumar, B. V.

2011-01-01

With the intent of improving the safety characteristics of lithium ion cells, electrolytes containing flame retardant additives have been investigated. A number of triphenyl phosphate-containing electrolytes were evaluated in both coin cells and experimental three electrode lithium-ion cells (containing reference electrodes). A number of chemistries were investigated, including MCMB carbon/LiNi(0.8)Co(0.2)O2 (NCO), graphite/LiNi(0.8)Co(0.15)Al(0.05)O2 (NCA), Li/Li(Li(0.17)Ni(0.25)Mn(0.58))O2, Li/LiNiMnCoO2 (NMC) and graphite/LiNiMnCoO2 (NMC), to study the effect that different electrolyte compositions have upon performance. A wide range of TPP-containing electrolytes were demonstrated to have good compatibility with the C/NCO, C/NCA, and Li/NMC systems, however, poor performance was initially observed with the high voltage C/NMC system. This necessitated the development of improved electrolytes with stabilizing additives, leading to formulations containing lithium bis(oxalato)borate (LiBOB) that displayed substantially improved performance.

Equilibrium and kinetics of co-extraction of U(VI) and HNO3 using tri-n-butyl phosphate and tri-iso-amyl phosphate in paraffin

International Nuclear Information System (INIS)

Das, Diptendu; Juvekar, V.A.; Biswas, Sujoy; Roy, S.B.; Bhattacharya, R.

2014-01-01

Tri-n-butyl phosphate (TBP) is versatile solvent for recovery of actinides as it is cheaper and the extracted actinides can be stripped from the loaded organic phase using plain water. However there are inherent problems associated TBP such as i) formation of the third phase ii) high solubility in aqueous phase iii) radiolytic hydrolysis at high radiation environment and iv) high propensity for extraction of mineral acids. The last mentioned property makes it less suitable for liquid emulsion membrane (LEM) extraction where acid transport to the strip phase drastically reduces extraction efficiency. Therefore there is need to replace TBP with an extractant which has lesser propensity for acid extraction. Many researcher reported Tri-iso-amyl phosphate (TiAP) as an alternative extractant which can sustain high radiation environment without chemical/radiative degradation. However there are no studies available on co-extraction of U(VI) and mineral acids by TiAP. In this research paper equilibrium and kinetics of co-extraction of U(VI) and HNO 3 from nitric acid medium into a hydrocarbon phase (paraffin) using Tri n- butyl phosphate (TBP), Tri-iso-amyl phosphate (TiAP) has been studied. Relative rates of extraction of uranium(VI) and HNO 3 by TiAP and TBP were measured simultaneously using bulk-liquid membrane (BLM) system. Study reveals although TiAP is less efficient in extracting U(IV), than TBP, it transfers lesser quantity of nitric acid to organic phase. Hence TiAP is more suitable as a carrier for LEM extraction than TBP

The use tri-n-butyl phosphate in plutonium extraction. Radiolysis and recycling of the solvent (1963); Le phosphate de tri-n-butyle dans l'extraction du plutonium. Radiolyse et recyclage du solvant (1963)

Energy Technology Data Exchange (ETDEWEB)

Isaac, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1963-07-01

The work concerns the radiolysis and recycling of tri-n-butyl phosphate used as extraction solvent for plutonium. The radiolysis is studied on an industrial solvent using a cobalt 60 source. Figures are given for the yield of the mono- and di-butyl-phosphoric acids formed from the dry and water-saturated solvents and the influence of nitric acid on the formation of dibutyl-phosphoric acid is indicated. The recycling treatment of the solvent is reconsidered with a view to lowering the residual contamination due to fission products. The tests carried out on a solvent from the plutonium extraction plant at Marcoule show the efficiency of the sodium carbonate treatment. Of all the products studied, only caustic soda led to a better decontamination than sodium carbonate; in all cases however, the elimination of ruthenium is always incomplete. (author) [French] L'etude porte sur la radiolyse et le recyclage du phosphate de tri-n-butyle utilise comme solvant d'extraction du plutonium. La radiolyse est etudiee sur un solvant industriel a l'aide d'une source de cobalt 60. On donne les rendements de formation des acides mono- et dlbutylphosphoriques a partir de solvants secs et satures d'eau, et on montre l'influence de l'acide nitrique sur la formation de l'acide dibutylphosphorique. Le traitement de recyclage du solvant est repris en vue d'abaisser la contamination residuelle en produits de fission. Les essais, effectues sur un solvant provenant de l'usine d'extraction du plutonium de Marcoule, montrent l'efficacite du traitement au carbonate de sodium. De tous les reactifs etudies, seule la soude a donne une decontamination superieure au carbonate de sodium; mais dans tous les cas, l'elimination du ruthenium est toujours incomplete. (auteur)

Optimized Li-Ion Electrolytes Containing Triphenyl Phosphate as a Flame-Retardant Additive

Science.gov (United States)

Smart, Marshall C.; Bugga, Ratnakumar V.; Prakash, G. K. Surya; Krause, Frederick C.

2011-01-01

A number of future NASA missions involving the exploration of the Moon and Mars will be human-rated and thus require high-specific-energy rechargeable batteries that possess enhanced safety characteristics. Given that Li-ion technology is the most viable rechargeable energy storage device for near-term applications, effort has been devoted to improving the safety characteristics of this system. There is also a strong desire to develop Li-ion batteries with improved safety characteristics for terrestrial applications, most notably for hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle (PHEV) automotive applications. Therefore, extensive effort has been devoted recently to developing non-flammable electrolytes to reduce the flammability of the cells/battery. A number of electrolyte formulations have been developed, including systems that (1) incorporate greater concentrations of the flame-retardant additive (FRA); (2) use di-2,2,2-trifluoroethyl carbonate (DTFEC) as a co-solvent; (3) use 2,2,2- trifluoroethyl methyl carbonate (TFEMC); (4) use mono-fluoroethylene carbonate (FEC) as a co-solvent and/or a replacement for ethylene carbonate in the electrolyte mixture; and (5) utilize vinylene carbonate as a "SEI promoting" electrolyte additive, to build on the favorable results previously obtained. To extend the family of electrolytes developed under previous work, a number of additional electrolyte formulations containing FRAs, most notably triphenyl phosphate (TPP), were investigated and demonstrated in experimental MCMB (mesocarbon micro beads) carbon- LiNi(0.8)Co(0.2)O2 cells. The use of higher concentrations of the FRA is known to reduce the flammability of the electrolyte solution, thus, a concentration range was investigated (i.e., 5 to 20 percent by volume). The desired concentration of the FRA is the highest amount tolerable without adversely affecting the performance in terms of reversibility, ability to operate over a wide temperature range, and

Spectrophotometric determination of dissolved tri n-butyl phosphate in aqueous streams of Purex process

International Nuclear Information System (INIS)

Ganesh, S.; Velavendan, P.; Pandey, N.K.; Ahmed, M.K.; Kamachi Mudali, U.; Natarajan, R.

2012-01-01

A spectrophotometric method is developed for the determination of dissolved tri-n butyl phosphate (TBP) in aqueous streams of Purex process used in nuclear fuel reprocessing. The method is based on the formation of phosphomolybdate with added ammonium molybdate followed by reduction with hydrazine sulphate in acid medium. Orthophosphate and molybdate ions combine in acidic solution to give molybdophosphoric (phosphomolybdic) acid, which upon selective reduction (with hydrazinium sulphate) produces a blue colour, due to molybdenum blue. The intensity of blue colour is proportional to the amount of phosphate. If the acidity at the time of reduction is 0.5 M in sulphuric acid and hydrazinium sulphate is the reductant, the resulting blue complex exhibits maximum absorption at 810-840 nm. The system obeys Lambert-Beer's law at 830 nm in the concentration range of 0.1-1.0 μg/mol of phosphate. Molar Absorptivity was determined to be 3.1 x 10 4 L mol -1 cm -1 at 830 nm. The results obtained are reproducible with standard deviation of 1 % and relative error less than 2 % and are in good agreement with those obtained by ion chromatographic technique. (author)

NIOSH Manual of Analytical Methods (third edition). Fourth supplement

Energy Technology Data Exchange (ETDEWEB)

1990-08-15

The NIOSH Manual of Analytical Methods, 3rd edition, was updated for the following chemicals: allyl-glycidyl-ether, 2-aminopyridine, aspartame, bromine, chlorine, n-butylamine, n-butyl-glycidyl-ether, carbon-dioxide, carbon-monoxide, chlorinated-camphene, chloroacetaldehyde, p-chlorophenol, crotonaldehyde, 1,1-dimethylhydrazine, dinitro-o-cresol, ethyl-acetate, ethyl-formate, ethylenimine, sodium-fluoride, hydrogen-fluoride, cryolite, sodium-hexafluoroaluminate, formic-acid, hexachlorobutadiene, hydrogen-cyanide, hydrogen-sulfide, isopropyl-acetate, isopropyl-ether, isopropyl-glycidyl-ether, lead, lead-oxide, maleic-anhydride, methyl-acetate, methyl-acrylate, methyl-tert-butyl ether, methyl-cellosolve-acetate, methylcyclohexanol, 4,4'-methylenedianiline, monomethylaniline, monomethylhydrazine, nitric-oxide, p-nitroaniline, phenyl-ether, phenyl-ether-biphenyl mixture, phenyl-glycidyl-ether, phenylhydrazine, phosphine, ronnel, sulfuryl-fluoride, talc, tributyl-phosphate, 1,1,2-trichloro-1,2,2-trifluoroethane, trimellitic-anhydride, triorthocresyl-phosphate, triphenyl-phosphate, and vinyl-acetate.

Analysis and development of methods for the recovery of degraded tri-n-butyl phosphate (TBP)-30%V/V-dodecane

International Nuclear Information System (INIS)

Dalston, C.O.

1984-01-01

Tri-n-butyl phosphate associated with an inert hydrocarbon, is the principal solvent used in reprocessing of nuclear irradiated fuel arising of pressurized water reactors, nowdays. The combined action of radiation and nitric acid cause severe damage to solvent, in reprocessing steps. Then, the recovery of solvent gets some importance, since it decreases the amount of the waste and improves the economy of the process. A comparative analysis of several methods of the recovery of this solvent was done, such as: alkaline washing, adsortion with resins, adsorption with aluminium oxide, adsorption by active carbon and adsorption by vermiculite. Some modifications of the analytical test of 95 Zr and a mathematical definition of two new parameters were done: the degradation grade and the eficiency of recovering. Through this modified test of 95 Zr, the residence time and the rate of degraded solvent: recuperator, were determined. After the laboratory tests had been performed, vermiculite, associated with active carbon, were employed in the treatment of 50 liters of tri-n-butyl phosphate (30%V/V)-dodecane, degraded by hydrolysis. Succeding analyses were made to check up the potentialities of these solids in the recovering of this solvent. (Author) [pt

Silver di-t-butyl phosphate, a useful reagent in the synthesis of phospholipids. Synthesis of mixed-acid phosphatidic acid and phosphatidyl glycerolphosphate

NARCIS (Netherlands)

Bonsen, P.P.M.; Haas, Gerard H. de

The synthesis of silver di-t-butyl phosphate is described. Using this reagent, mixed-acid phosphatidic acid with one unsaturated fatty acid could be prepared by means of a reaction with a 1,2-diacyl glycerol-3-iodohydrin. The blocking groups could be removed easily with dry hydrogen chloride at low

Dielectric studies on binary mixtures of Tri-n-butyl phosphate (TBP) and long-chain primary alcohols (modifiers)

International Nuclear Information System (INIS)

Dash, S.K.; Swain, B.B.

1993-01-01

Dielectric constant (ε) of Tri-n-butyl phosphate (TBP), in binary mixtures with five long-chain primary alcohols viz; 1-butanol, 1-pentanol, 1-hexanol, 1-heptanol and 1-octanol has been measured at ν = 455 kHz and at temperature 302 K. The data is used to evaluate mutual correlation factor g ab , excess molar polarization ΔP and excess free energy of mixing ΔF ab by using Winkelmann-Quitzsch eqn. for binary mixtures to assess the suitability of the alcohols as modifiers. The trend of variation of these parameters exhibit marked dependence on chain-length of the alcohols indicating 1-heptanol to be an efficient modifier. (author)

Distribution and identification of Plutonium(IV) species in tri-n-butyl phosphate/HNO3 extraction system containing acetohydroxamic acid

International Nuclear Information System (INIS)

Tkac, P.; Paulenova, A.; Vandegrift, G.F.; Krebs, J.F.

2009-01-01

There was a significant research progress achieved with the aim to modify conventional PUREX process by stripping of plutonium from the tri-n-butyl phosphate (TBP) extraction product in the form of non-extractable complexes upon addition of back-hold complexation agents. The present paper reports effects of such salt-free complexant, acetohydroxamic acid (HAHA), on distribution ratio of Pu(IV) under wide concentration of nitric acid and additional nitrate. General formula of plutonium species present in the organic phase can be described as Pu(OH) x (AHA) y (NO3) 4-x-y x 2TBP x wHNO 3 . (author)

Inhibition Effect of 1-Butyl-4-Methylpyridinium Tetrafluoroborate on the Corrosion of Copper in Phosphate Solutions

Directory of Open Access Journals (Sweden)

M. Scendo

2011-01-01

Full Text Available The influence of the concentration of 1-Butyl-4-methylpyridinium tetrafluoroborate (4MBPBF4 as ionic liquid (IL on the corrosion of copper in 0.5 M PO43− solutions of pH 2 and 4 was studied. The research involved electrochemical polarization method, and scanning electron microscopy (SEM technique. The results obtained showed that the inhibition efficiency of corrosion of copper increases with an increase in the concentration of 4MBPBF4 but decreases with increasing temperature. The thermodynamic functions of corrosion analysis and adsorptive behavior of 4MBPBF4 were carried out. During the test, the adsorption of the inhibitor on the copper surface in the phosphate solutions was found to obey the Langmuir adsorption isotherm and had a physical mechanism.

Carboxylesterase-involved metabolism of di-n-butyl phthalate in pumpkin (Cucurbita moschata) seedlings.

Science.gov (United States)

Lin, Qingqi; Chen, Siyuan; Chao, Yuanqing; Huang, Xiongfei; Wang, Shizhong; Qiu, Rongliang

2017-01-01

Uptake and accumulation by plants is a significant pathway in the migration and transformation of phthalate esters (PAEs) in the environment. However, limited information is available on the mechanisms of PAE metabolism in plants. Here, we investigated the metabolism of di-n-butyl phthalate (DnBP), one of the most frequently detected PAEs, in pumpkin (Cucurbita moschata) seedlings via a series of hydroponic experiments with an initial concentration of 10 mg L -1 . DnBP hydrolysis occurred primarily in the root, and two of its metabolites, mono-n-butyl phthalate (MnBP) and phthalic acid (PA), were detected in all plant tissues. The MnBP concentration was an order of magnitude higher than that of PA in shoots, which indicated MnBP was more readily transported to the shoot than was PA because of the former's dual hydrophilic and lipophilic characteristics. More than 80% of MnBP and PA were located in the cell water-soluble component except that 96% of MnBP was distributed into the two solid cellular fractions (i.e., cell wall and organelles) at 96 h. A 13-20% and 29-54% increase of carboxylesterase (CXE) activity shown in time-dependent and concentration-dependent experiments, respectively, indicated the involvement of CXEs in plant metabolism of DnBP. The level of CXE activity in root subcellular fractions was in the order: the cell water-soluble component (88-94%) > cell wall (3-7%) > cell organelles (3-4%), suggesting that the cell water-soluble component is the dominant locus of CXE activity and also the domain of CXE-catalyzed hydrolysis of DnBP. The addition of triphenyl phosphate, a CXE inhibitor, led to 43-56% inhibition of CXE activity and 16-25% increase of DnBP content, which demonstrated the involvement of CXEs in plant metabolism of DnBP. This study contributes to our understanding of enzymitic mechanisms of PAE transformation in plants. Copyright © 2016 Elsevier Ltd. All rights reserved.

Initiation Temperature for Runaway Tri-n-Butyl Phosphate/Nitric Acid Reaction

Energy Technology Data Exchange (ETDEWEB)

Rudisill, T.S.

2000-11-28

During a review of the H-Canyon authorization basis, Defense Nuclear Facility Safety Board (DNFSB) staff members questioned the margin of safety associated with a postulated tri-n-butyl phosphate (TBP)/nitric acid runaway reaction due to the inadvertent heating of a canyon tank containing greater than 3000 lbs (1362 kg) of TBP. The margin of safety was partially based on experiments and calculations performed by the Actinide Technology Section (ATS) to support deletion of indication of tank agitation as a Safety Class System. In the technical basis for deletion of this system, ATS personnel conservatively calculated the equilibrium temperature distribution of a canyon tank containing TBP and nitric acid layers which were inadvertently heated by a steam jet left on following a transfer. The maximum calculated temperature (128 degrees C) was compared to the minimum initiation temperature for a runaway reaction (greater than 130 degrees C) documented by experimental work in the mid 195 0s. In this work, the initiation temperature as a function of nitric acid concentration was measured for 0 and 20 wt percent dissolved solids. The DNFSB staff members were concerned that data for 0 wt percent dissolved solids were not conservative given the facts that data for 20 wt percent dissolved solids show initiation temperatures at or below 130 degrees C and H-Canyon solutions normally contained a small amount of dissolved solids.

on association of trialkyl phosphates

International Nuclear Information System (INIS)

Petkovic, D.M.; Maksimovic, Z.B.

1976-01-01

The association constants of tri-n-butyl (TBP), tri-n-propyl (TPP) and triethyl phosphate (TEP) with chloroform, carbon tetrachloride and benzene were determined by dielectric constant, proton magnetic resonance and vapor pressure measurements. Correlation of the trialkyl phosphate-chloroform association constants, using the Hammett equation, showed their increase with the number of carbon atoms in the aliphatic radicals. The change of trialkyl phosphate reactivity with temperature was used to determine the thermodynamic quantities. (author)

Solvent Extraction of Tellurium from Chloride Solutions Using Tri-n-butyl Phosphate: Conditions and Thermodynamic Data

Directory of Open Access Journals (Sweden)

Dongchan Li

2014-01-01

Full Text Available The extractive separation of tellurium (IV from hydrochloric acid media with tri-n-butyl phosphate (TBP in kerosene was investigated. The dependence on the extraction of tellurium species, concentrations of tellurium and TBP, extraction time and stage, organic/aqueous ratio, and interferences from coexist metallic ions were examined and are discussed. Besides, the stripping agent and stripping time were also studied. It was found that the extraction reaction corresponds to the neutral complex formation mechanism and the extracted species is TeCl4·3TBP and that the extraction process is exothermic. The thermodynamic parameters of enthalpy ΔH, entropy ΔS, and free energy ΔG of the extraction process were evaluated at −26.2 kJ·mol−1, −65.6 J·mol−1·K−1, and −7.0 kJ·mol−1, respectively at 293 K.

Radiation chemistry of a mixture of benzene and cyclohexane in presence of triphenyl stibine

Energy Technology Data Exchange (ETDEWEB)

Nazir, S B; Rai, R S [Birla Inst. of Tech. and Science, Pilani (India). Dept. of Chemistry

1976-08-01

Following previously reported work (Peterson et al. J. Phys. Chem.; 71: 4506 (1967)) on the radiolysis of triphenyl stibine in benzene from which it was concluded that the energy is absorbed by benzene and excited benzene molecules transfer their energy to the metal phenyl which does not decompose due to quenching and since benzene is a protective agent for cyclohexane against ..gamma.. radiation, a system consisting of benzene, cyclohexane and triphenyl stibine has been used to study the energy transfer processes and the nature of protection. It was found that /sup 60/C0 ..gamma.. radiolysis of cyclohexane in presence of 1 x 10/sup -2/M triphenyl stibine formed two isomers of pentane and hexane and hexene, methylcyclopentane, benzene and cyclohexene. G values of these products, except those of hexene and methylcyclopentane are negligible. All products except these two are eliminated in the radiolysis of this system in presence of benzene. G values of these products are reduced considerably. The mechanism of formation of these compounds and a sponge type protection have been postulated to explain the results.

Assessment of human hair as an indicator of exposure to organophosphate flame retardants. Case study on a Norwegian mother-child cohort.

Science.gov (United States)

Kucharska, Agnieszka; Cequier, Enrique; Thomsen, Cathrine; Becher, Georg; Covaci, Adrian; Voorspoels, Stefan

2015-10-01

A major challenge of non-invasive human biomonitoring using hair is to assess whether it can be used as an indicator of exposure to Flame Retardants, such as Organophosphate Flame Retardants (PFRs), since the contribution of atmospheric deposition (air and/or dust) cannot be neglected. Therefore, the aim of this study was to evaluate the suitability of using human hair more thoroughly by comparison of (i) levels of PFRs in human hair (from 48 mothers and 54 children), with levels measured in dust and air in their respective households; and (ii) levels of selected PFRs in hair with the levels of corresponding PFR metabolites in matching urine samples collected simultaneously. Most PFRs (tri-n-butyl phosphate (TNBP), 2-ethyl-hexyldiphenyl phosphate (EHDPHP), tri-phenyl phosphate (TPHP), tri-iso-butyl phosphate (TIBP), and tris(2-butoxyethyl) phosphate (TBOEP)) were detected in all human hair samples, tris(2-ethylhexyl) phosphate (TEHP) and tris(1,3-dichloro-iso-propyl) phosphate (TDCIPP) in 93%, tri-cresyl-phosphate (TCP) in 69% and tris(2-chloroethyl) phosphate (TCEP) in 21% of the samples. Levels of individual PFRs ranged between human hair and PFR levels in house dust and/or air were found, e.g. Spearman correlation (rS = 0.561, p exposure. To the best of our knowledge, this is the first study with such design and our findings might help to understand human exposure to and body burdens of PFRs. Copyright © 2015 Elsevier Ltd. All rights reserved.

Radiation-chemical reaction of 2,3,5-triphenyl-tetrazolium chloride in liquid and solid state

DEFF Research Database (Denmark)

Kovacs, A.; Wojnarovits, L.; McLaughlin, W.L.

1996-01-01

In pulse radiolysis of 2,3,5-triphenyl-tetrazolium chloride (TTC) at around 360 nm fast formation of intermediate tetrazolium radical was observed under both oxidizing and reducing conditions. In the latter case bimolecular formation of formazan, absorbing at around 480 nm, was observed. This rea......In pulse radiolysis of 2,3,5-triphenyl-tetrazolium chloride (TTC) at around 360 nm fast formation of intermediate tetrazolium radical was observed under both oxidizing and reducing conditions. In the latter case bimolecular formation of formazan, absorbing at around 480 nm, was observed...

Occupational irritant contact folliculitis associated with triphenyl tin fluoride (TPTF) exposure

DEFF Research Database (Denmark)

Andersen, Klaus Ejner; Petri, M

1982-01-01

Triphenyl tin fluoride (TPTF) is a bioactive organo-tin compound used in concentrations 2-12% as anti-foulants in boat paints. The chemical is moderately toxic to the skin. An occupational irritant contact folliculitis from TPTF in a marine paint plant worker is described. Contact allergy...

Neutron-scattering study of low-energy excitations in triphenyl phosphite

CERN Document Server

Mayer, J; Massalska-Arodz, M; Janik, J A; Natkaniec, I; Steinsvoll, O

2002-01-01

The low-energy excitations in crystalline and glassy triphenyl phosphite were studied by inelastic incoherent neutron scattering with two different instruments. The results - the incoherent dynamic structure factor S(2 theta,omega) and the density of states G(omega) - were obtained using direct and inverted geometry time-of-flight spectrometers, respectively. The probable origin of the excess density of states in the glass (boson peak) is discussed. (orig.)

Neutron-scattering study of low-energy excitations in triphenyl phosphite

International Nuclear Information System (INIS)

Mayer, J.; Krawczyk, J.; Massalska-Arodz, M.; Janik, J.A.; Natkaniec, I.; Steinsvoll, O.

2002-01-01

The low-energy excitations in crystalline and glassy triphenyl phosphite were studied by inelastic incoherent neutron scattering with two different instruments. The results - the incoherent dynamic structure factor S(2θ,ω) and the density of states G(ω) - were obtained using direct and inverted geometry time-of-flight spectrometers, respectively. The probable origin of the excess density of states in the glass (boson peak) is discussed. (orig.)

Molecular dynamics simulations of tri-n-butyl-phosphate/n-dodecane mixture: thermophysical properties and molecular structure.

Science.gov (United States)

Cui, Shengting; de Almeida, Valmor F; Khomami, Bamin

2014-09-11

Molecular dynamics simulations of tri-n-butyl-phosphate (TBP)/n-dodecane mixture in the liquid phase have been carried out using two recently developed TBP force field models (J. Phys. Chem. B 2012, 116, 305) in combination with the all-atom optimized potentials for liquid simulations (OPLS-AA) force field model for n-dodecane. Specifically, the electric dipole moment of TBP, mass density of the mixture, and the excess volume of mixing were computed with TBP mole fraction ranging from 0 to 1. It is found that the aforementioned force field models accurately predict the mass density of the mixture in the entire mole fraction range. Commensurate with experimental measurements, the electric dipole moment of the TBP was found to slightly increase with the mole fraction of TBP in the mixture. Also, in accord with experimental data, the excess volume of mixing is positive in the entire mole fraction range, peaking at TBP mole fraction range 0.3-0.5. Finally, a close examination of the spatial pair correlation functions between TBP molecules, and between TBP and n-dodecane molecules, revealed formation of TBP dimers through self-association at close distance, a phenomenon with ample experimental evidence.

Co-extraction and co-stripping of U(VI) and Pu(IV) using tri-iso-amyl phosphate and tri-n-butyl phosphate in n-dodecane from nitric acid media under high loading conditions

Energy Technology Data Exchange (ETDEWEB)

Sreenivasulu, Balija; Suresh, Ammath; Sivaraman, Nagarajan; Rao, P.R. Vasudeva [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Chemistry Group

2016-08-01

The extraction of Pu(IV) using 1.1 M solution of tri-iso-amyl phosphate (TiAP)/n-dodecane (DD) from plutonium nitrate solutions in nitric acid media was examined as a function of equilibrium aqueous phase metal ion concentration and equilibrium aqueous phase acidity at 303 K. The nitric acid concentration in the organic phase was measured as a function of equilibrium organic phase plutonium concentration. The co-extraction of U(VI) and Pu(IV) was studied using 1.1 M TiAP/DD system as a function of their equilibrium aqueous phase metal ion concentration and compared with 1.1 M tri-n-butyl phosphate (TBP)/n-DD system under identical conditions. Co-extraction and co-stripping of U(VI) and Pu(IV) were studied using 1.1 M TiAP/DD and 1.1 M TBP/DD systems in cross current mode to evaluate the number of stages required for the extraction and stripping of heavy metal ions (uranium and plutonium). The extraction and stripping efficiencies were calculated for both the systems. The saturation limit of the organic phase was also established in these studies.

Co-extraction and co-stripping of U(VI) and Pu(IV) using tri-iso-amyl phosphate and tri-n-butyl phosphate in n-dodecane from nitric acid media under high loading conditions

International Nuclear Information System (INIS)

Sreenivasulu, Balija; Suresh, Ammath; Sivaraman, Nagarajan; Rao, P.R. Vasudeva

2016-01-01

The extraction of Pu(IV) using 1.1 M solution of tri-iso-amyl phosphate (TiAP)/n-dodecane (DD) from plutonium nitrate solutions in nitric acid media was examined as a function of equilibrium aqueous phase metal ion concentration and equilibrium aqueous phase acidity at 303 K. The nitric acid concentration in the organic phase was measured as a function of equilibrium organic phase plutonium concentration. The co-extraction of U(VI) and Pu(IV) was studied using 1.1 M TiAP/DD system as a function of their equilibrium aqueous phase metal ion concentration and compared with 1.1 M tri-n-butyl phosphate (TBP)/n-DD system under identical conditions. Co-extraction and co-stripping of U(VI) and Pu(IV) were studied using 1.1 M TiAP/DD and 1.1 M TBP/DD systems in cross current mode to evaluate the number of stages required for the extraction and stripping of heavy metal ions (uranium and plutonium). The extraction and stripping efficiencies were calculated for both the systems. The saturation limit of the organic phase was also established in these studies.

Biodegradation of tert-butylphenyl diphenyl phosphate

International Nuclear Information System (INIS)

Heitkamp, M.A.; Freeman, J.P.; Cerniglia, C.E.

1986-01-01

The biodegradation of tert-butylphenyl diphenyl phosphate (BPDP) was examined in microcosms containing sediment and water from five different ecosystems as part of studies to elucidate the environmental fate of phosphate ester flame retardants. Biodegradation of [ 14 C]BPDP was monitored in the environmental microcosms by measuring the evolution of 14 CO 2 . Over 37% of BPDP was mineralized after 8 weeks in microcosms from an ecosystem which had chronic exposure to agricultural chemicals. In contrast, only 1.7% of BPDP was degraded to 14 CO 2 in samples collected from a noncontaminated site. The exposure concentration of BPDP affected the percentage which was degraded to 14 CO 2 in microcosms from the two most active ecosystems. Mineralization was highest at a concentration of 0.1 mg of BPDP and was inhibited with 10- and 100-fold higher concentrations of BPDP. The authors observed adaptive increases in both microbial populations and phosphoesterase enzymes in some sediments acclimated to BPDP. Chemical analyses of the residues in the microcosms indicated undegraded BPDP and minor amounts of phenol, tert-butylphenol, diphenyl phosphate, and triphenyl phosphate as biodegradation products. These data suggest that the microbial degradation of BPDP results from at least three catabolic processes and is highest when low concentrations of BPDP are exposed to sediment microorganisms of eutrophic ecosystems which have high phosphotri- and diesterase activities and previous exposure to anthropogenic chemicals

Co-extraction of lactic acid by tri-n-octylamine and tri-n-butyl phosphate; Tori-n-okuchiruamin to tori-n-rinsanbuchiru niyoru nyusan no kyodochushutsu

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, Michiaki; Yuba, Seiji; Kondo, Kazui

1999-01-05

Co-extraction of lactic acid was examined as a fundamental research for establishing in situ extraction fermentation process of lactic acid (HA). Addition of tri-n-butyl phosphate (TBP) into an extraction system of lactic acid by tri-n-octylamine (TOA) using hexane as the dilutor brought about a great cooperative effect. The extracting reaction in this system is analyzed by taking into consideration the formation of HA-TOA-2TBP. Further, when a TBP and TOA-containing hexane solution was added into a culture system of a lactic acid bacteria Lactobacillus rhamnosus, latic acid of 65% in a system without addition of an organic solvent was produced. (translated by NEDO)

Unsymmetrical phosphate as extractant for the extraction of nitric acid

International Nuclear Information System (INIS)

Gaikwad, R.H.; Jayaram, R.V.

2016-01-01

Tri-n-butyl phosphate (TBP) was first used as an extractant in 1944, during Manhattan project for the separation of actinides and further explored by Warf in 1949 for the extraction of Ce(IV) from aqueous nitric acid. TBP was further used as an extractant in the Plutonium Uranium Recovery by Extraction (PUREX) process. To meet the stringent requirements of the nuclear industry TBP has been extensively investigated. In spite of its wide applicability, TBP suffers from various disadvantages such as high aqueous solubility, third phase formation, chemical and radiation degradation leading to the formation of undesired products. It also suffers from incomplete decontamination of the actinides from fission products. Various attempts have been made to overcome the problems associated with TBP by way of using higher homologues of TBP such as Tri-iso amyl phosphate (TiAP), Tri-secondary butyl phosphate (TsBP), Tri amyl phosphate (TAP). It was found that in some cases the results were considerably better than those obtained with TBP for uranium/thorium extraction. The extraction of nitric acid by TBP and its higher homologues which are symmetrical are well documented. However, no solvent has emerged clearly superior than TBP. Here in we report the extraction of nitric acid with neutral unsymmetrical phosphates and study them as extractants for the extraction of nitric acid. Dibutyl secbutyl phosphate, dibutyl pentyl phosphate and dibutyl heptyl phosphate were synthesised for this purpose and the extraction of nitric acid was studied in n-dodecane. The results indicate that the substitution of one of the alkyl groups of the symmetrical phosphate adjacent to the phosphoryl (P=O) group of the phosphate does not have any pronounced effect on the extraction capacity of nitric acid. (author)

Diluent and extractant effects on the enthalpy of extraction of uranium(VI) and americium(III) nitrates by trialkyl phosphates

International Nuclear Information System (INIS)

Srinivasan, T.G.; Vasudeva Rao, P.R.; Sood, D.D.

1998-01-01

The effect of various diluents such as n-hexane, n-heptane n-octane, isooctane, n-decane, n-undecane, n-dodecane, n-tetradecane, n-hexadecane, cyclohexane, benzene, toluene, p-xylene, mesitylene and o-dichlorobenzene on the enthalpy of extraction of uranyl nitrate by tri-n-amyl phosphate (TAP) over the temperature range 283 K--333 K has been studied. The results indicate that the enthalpy of extraction does not vary significantly with the diluents studied. Also enthalpies of extraction of uranyl nitrate and americium(III) nitrate by neutral organo phosphorous extractants such as tri-n-butyl phosphate (TBP), tri-n-amyl phosphate (TAP), tri-sec-butyl phosphate (TsBP), tri-isoamyl phosphate (TiAP) and tri-n-hexyl phosphate (THP) have been studied. An attempt has been made to explain the trends, on the basis of the nature of the solvate formed and the different terms which contribute to the overall enthalpy change

Characterization and Exergy Analysis of Triphenyl Borate

International Nuclear Information System (INIS)

Acarali, N. B.

2015-01-01

In this study, unlike from the literature, boron oxide, borax decahydrate, boric acid and borax pentahydrate as boron sources were used to synthesize Triphenyl Borate (TPB). The reactions of TPB were carried out by using both phenol and various boron sources in inert water-immiscible organic solvent successfully. On the basis of analyzes (FT-IR, SEM, TGA/DSC) obtained, it was seen that phenol acted as a support to borate structure framework and thermal characterisation of the amorphous solid under determined conditions suggested that usage of different boron sources had effects for glass transition temperature in TPB production. The exergy analysis was performed to the TPB production to determine efficiency. The exergy analysis showed that the highest exergy efficiency was obtained by using boron oxide as a boron source. Consequently, all analyses results showed that TPB was produced successfully. Accordingly, characterization and exergy analysis supported each other. (author)

Time course of electrophysiologic effects induced by di-n-butyl-2,2-dichlorovinyl phosphate (DBCV) in the adult hen.

Science.gov (United States)

Robertson, D G; Mattson, A M; Bestervelt, L L; Richardson, R J; Anderson, R J

1988-01-01

Previous work in our laboratory indicated that di-n-butyl-2,2-dichlorovinyl phosphate (DBCV) produced electrophysiologic changes in hen peripheral nerve that coincided with the development of histopathologic changes and neurologic signs of peripheral neuropathy. The purpose of the present study was to follow the time course for the development of the electrophysiologic changes and to determine whether pretreatment with the phosphinate analog of DBCV (DBCV-P), a nonageable organophosphorus compound, prevented these effects. Although significant electrophysiologic deficits occurred in the tibial and sciatic nerve 24 h after DBCV treatment, the most marked changes coincided with the onset of clinical signs of organophosphorus-induced delayed neuropathy (14-21 d). The sciatic and tibial nerves were equally susceptible to DBCV in producing deficits characterized by changes in the relative refractory period and an increased strength-duration threshold. Pretreatment with DBCV-P prevented the clinical signs and also attenuated the electrophysiologic deficits induced by DBCV treatment. These data suggest that electrophysiologic deficits occur before clinical signs of organophosphorus-induced delayed neuropathy (OPIDN) and may be indicative of a link between neurotoxic esterase (NTE) inhibition and onset of overt clinical toxicity.

Recovering/recycling of butyl and halogenated butyl rubber via ionizing radiation

International Nuclear Information System (INIS)

Martin, Sandra Regina Scagliusi

2013-01-01

Polymeric materials (plastics and rubbers) attain a continuous and raising proportion of urban and industrial scraps discarded in landfills; their impact on environment are more and more concerning. The implementation of new technologies in order to reduce impacts of plastic waste on the environment, at an effective cost, proved to be a great problem, due to inherent complexity for polymers re-using. Ionizing radiation is capable to modify structure and properties of polymeric material. Butyl and halobutyl rubbers have been used within a comprehensive scale, applications such as tires spare parts and diverse artifacts. The major high energy photon effect, as gamma-rays in butyl and halo butyl rubbers consists in free-radicals generation along changes in mechanical properties.This work aims to the development of controlled degradation processes (devulcanization) of butyl and halo butyl (chlorine and bromine) rubbers, in order to characterize their availability for transformation and modification of properties. Experimental results obtained showed that butyl and halobutyl rubbers,irradiated at 25 kGy and further sheared, are able to be used as an initial point for mixtures with pristine. (author)

Studies on third phase formation in the extraction of Zr(NO3)4 by solutions of tri-iso-amyl phosphate and tri-n-butyl phosphate in n-dodecane

International Nuclear Information System (INIS)

Benadict Rakesh, K.; Suresh, A.; Vasudeva Rao, P.R.

2015-01-01

The knowledge about Limiting Organic Concentration (LOC) and Critical aqueous concentration (CAC) as a function of equilibrium aqueous phase HNO 3 concentration and extractant concentration is essential to restrict the metal ion concentration in the feed and loading of metal ion in to the organic phase to avoid third phase formation. Due to the lesser third phase formation tendency of tri-iso-amyl phosphate (TiAP) compared to tri-n-butyl phosphate (TBP) in the extraction of tetravalent metal ions, TiAP can be used as an alternate extractant to TBP for Zr/Hf separation. In this regard, the LOC and CAC values in the extraction of Zr(IV) by 1.1 M solutions of TiAP and TBP in n-dodecane from Zr(NO 3 ) 4 solutions with various concentrations of HNO 3 have been measured as a function of (HNO 3 ) aq,eq at 303K. The LOC and the CAC values decrease with increase in (HNO 3 ) aq,eq in all the cases. An increase in TBP concentration from 1.1 M to 2.2 M in the organic phase increases the LOC and the CAC. It is also observed that loading of Zr(IV) in 2.2 M TiAP/n-dodecane is much higher than Zr(IV) loading in 2.2 M TBP/n-dodecane under identical conditions. For example, 0.521 mol/L Zr(IV) can be loaded in 2.2 M TiAP/n-dodecane without third phase formation at 303K (corresponding CAC is 0.736 mol/L at 7.12 M HNO 3 ). It can be concluded that the third phase formation tendency is higher for TBP/n-dodecane-Zr(NO 3 ) 4 /HNO 3 system as compared to TiAP/n-dodecane- Zr(NO 3 ) 4 /HNO 3 system under identical conditions. (author)

Exposure of aircraft maintenance technicians to organophosphates from hydraulic fluids and turbine oils: a pilot study.

Science.gov (United States)

Schindler, Birgit Karin; Koslitz, Stephan; Weiss, Tobias; Broding, Horst Christoph; Brüning, Thomas; Bünger, Jürgen

2014-01-01

Hydraulic fluids and turbine oils contain organophosphates like tricresyl phosphate isomers, triphenyl phosphate and tributyl phosphate from very small up to high percentages. The aim of this pilot study was to determine if aircraft maintenance technicians are exposed to relevant amounts of organophosphates. Dialkyl and diaryl phosphate metabolites of seven organophosphates were quantified in pre- and post-shift spot urine samples of technicians (N=5) by GC-MS/MS after solid phase extraction and derivatization. Pre- and post shift values of tributyl phosphate metabolites (dibutyl phosphate (DBP): median pre-shift: 12.5 μg/L, post-shift: 23.5 μg/L) and triphenyl phosphate metabolites (diphenyl phosphate (DPP): median pre-shift: 2.9 μg/L, post-shift: 3.5 μg/L) were statistically higher than in a control group from the general population (median DBP: <0.25 μg/L, median DPP: 0.5 μg/L). No tricresyl phosphate metabolites were detected. The aircraft maintenance technicians were occupationally exposed to tributyl and triphenyl phosphate but not to tricresyl phosphate, tri-(2-chloroethyl)- and tri-(2-chloropropyl)-phosphate. Further studies are necessary to collect information on sources, routes of uptake and varying exposures during different work tasks, evaluate possible health effects and to set up appropriate protective measures. Copyright © 2013 Elsevier GmbH. All rights reserved.

Solubilization of meso-carbon microbeads by potassium- or dibutylzinc-promoted butylation and structural analysis of the butylated products; Mesocarbon microbeads no butyl ka ni yoru kayoka to erareta butyl kabutsu no kozo kaiseki

Energy Technology Data Exchange (ETDEWEB)

Murata, S.; Zhang, Y.; Kidena, K.; Nomura, M. [Osaka University, Osaka (Japan). Faculty of Engineering

1996-10-28

Tetrahydrofuran (THF) solubility and structure of the butylated products of meso-carbon microbeads (MCMB) were studied experimentally. In experiment, MCMB-A and MCMB-B obtained from two kinds of coal-tar pitch were used as specimens. MCMBs were butylated by BZ method using dibutylzinc-butyl iodide and KT method using K-butyl iodide-THF, and the butylated products were successfully obtained. The butylated products were investigated through THF solubility test, {sup 13}C-NMR measurement and gel permeation chromatography (GPC) measurement. As the experimental result, a BZ method produced the butylated products at a yield of nearly 170%, while a KT method produced them at a yield of nearly 130%. The THF solubility was estimated to be 89-97%. As the study result of molecular weight distributions by GPC measurement of solvent solubles, the molecular weight of raw material MCMB was estimated to be 590-770 in terms of polystyrene. 6 refs., 2 figs., 1 tab.

A Study of the Curing and Flammability Properties of Bisphenol A Epoxy Diacrylate Resin Utilizing a Novel Flame Retardant Monomer, bis[di-acryloyloxyethyl]-p-tert-butyl-phenyl Phosphate

Directory of Open Access Journals (Sweden)

Syang-Peng Rwei

2017-02-01

Full Text Available A UV-curable, flame-retardant monomer, DAPP (bis[di-acryloyloxyethyl]-p-tert-butyl-phenyl-phosphate, was synthesized based on BPDCP (4-tert-butylphenyl-dichloro phosphate and HEA (2-hydroxy ethyl acrylate. DAPP was blended with regular bisphenol A epoxy acrylate (BAEA in various ratios to yield various phosphorus contents. The TGA-IR (thermogravimetric analyzer interface with an infrared spectrometer results demonstrate that compounding 30 mol % DAPP with BAEA significantly reduced the amount of released CO gas. In contrast, the peak intensity of CO2 is independent of phosphorus content. The limiting oxygen index (LOI, reaching the saturated value of 26, and the heat release rate (HRR measured using a cone-calorimeter, 156.43 KW/m2, confirm the saturation point when 30 mol % DAPP was compounded into BAEA. A study of the kinetics of pyrolysis reveals that Ea decreases as the phosphorus content increases. Both the TGA-IR and pyrolysis results reveal that the phosphorus compound DAPP is easily decomposed during the initial stage of burning to form an insulating layer, which inhibits further burning of the resin and the consequent release of other flammable gases.

The thermal degradation of poly(iso-butyl methacrylate and poly(sec-butyl methacrylate

Directory of Open Access Journals (Sweden)

IVANKA G. POPOVIC

2000-12-01

Full Text Available The non-oxidative thermal degradation of poly(iso-butyl methacrylate and poly(sec-butyl methacrylate was investigated by studying changes in the polymer residue. Due to the different number of b-hydrogens in their ester substituents, these two polymeric isomers behave differently when subjected to elevated temperatures. Poly(iso-butyl methacrylate degrades quantitatively by depolymerisation with zip lengths of the same order of magnitude as those of poly(methyl methacrylate. Poly(sec-butyl methacrylate degrades by a combined degradation mechanism of depolymerisation and de-esterification. De-esterification becomes a significant thermolysis route at temperatures higher than 240°C.

4-Acetamido-N-(λ5-triphenyl­phospho­ranyl­idene)benzene­sulfonamide

Science.gov (United States)

Prugovečki, Biserka; Marinković, Marina; Vinković, Mladen; Dumić, Miljenko

2010-01-01

There are two independent mol­ecules per asymmetric unit of the title compound, C26H23N2O3PS. Their superposition shows that they differ in the conformation of the CH3CO– group and the benzene rings from the triphenyl­phospho­rane group. In the crystal structure, independent mol­ecules are inter­conected by strong N—H⋯O hydrogen bonds, forming infinite chains along the a axis. PMID:21579151

Interference of different ionic species on the analysis of phosphate in HLW using spectrophotometer

International Nuclear Information System (INIS)

Mishra, P.K.; Ghongane, D.E.; Valsala, T.P.; Sonavane, M.S.; Kulkarni, Y.; Changrani, R.D.

2010-01-01

During reprocessing of spent nuclear fuel by PUREX process different categories of radioactive liquid wastes like High Level (HL), Intermediate Level (IL) and Low Level (LL) are generated. Different methodologies are adopted for management of these wastes. Since PUREX solvent (30% Tri butyl phosphate-70% Normal Paraffin Hydrocarbon) undergoes chemical degradation in the highly acidic medium of dissolver solution, presence of phosphate in the waste streams is inevitable. Since higher concentrations of phosphate in the HLW streams will affect its management by vitrification, knowledge about the concentration of phosphate in the waste is essential before finalising the glass composition. Since a large number of anionic and cationic species are present in the waste, these species may interfere phosphate analysis using spectrophotometer. In the present work, the interference of different anionic and cationic species on the analysis of phosphate in waste solutions using spectrophotometer was studied

Compound list: butylated hydroxyanisole [Open TG-GATEs

Lifescience Database Archive (English)

Full Text Available butylated hydroxyanisole BHA 00156 ftp://ftp.biosciencedbc.jp/archive/open-tggates/...LATEST/Human/in_vitro/butylated_hydroxyanisole.Human.in_vitro.Liver.zip ftp://ftp.biosciencedbc.jp/archive/o...pen-tggates/LATEST/Rat/in_vivo/Liver/Single/butylated_hydroxyanisole.Rat.in_vivo.Liver.Single.zip ftp://ftp....biosciencedbc.jp/archive/open-tggates/LATEST/Rat/in_vivo/Liver/Repeat/butylated_hydroxyanisole.Rat.in_vivo.Liver.Repeat.zip ...

An efficient and highly selective ortho-tert-butylation of p-cresol with methyl tert-butyl ether catalyzed by sulfonated ionic liquids

Directory of Open Access Journals (Sweden)

Alamdari Reza Fareghi

2014-01-01

Full Text Available A novel series of sulfonic acid-functionalized ionic liquids (SFILs was found to act as efficient catalysts for ortho-tert-butylation of p-cresol with methyl tert-butyl ether (MTBE as the tert-butylating agent without an added solvent. The mono o-tert-butylated product was obtained in up to 80.4% isolated yield and 95.2% selectivity under such green conditions. No O-tert-butylated byproducts were formed.

Mutagenicity of 1-Ethyl-2,4,5-triphenyl-1H-imidazole and Six Derivatives in Salmonella typhimurium

OpenAIRE

KORKMAZ, Ferhan; Korkmaz, Ferhan; MERCANGOZ, Ayse

2010-01-01

 Newly synthesized 1-Ethyl-2,4,5-triphenyl-1H-imidazole and its six derivatives were tested by Ames assay. In order to reveal the mutagenic activities of the compounds, two different mutant strains of Salmonella typhimurium (TA98 and TA100) were used in an Ames assay with/without S9 microsomal fraction from rat liver. It was found that the compounds have no mutagenic activities.          &nb...

Radiochemical study of isomerization of free butyl cations

International Nuclear Information System (INIS)

Sinotova, E.N.; Nefedov, V.D.; Skorokhodov, S.S.; Arkhipov, Yu.M.

1987-01-01

Ion-molecular reactions of free butyl cations, generated by nuclear chemical method, with carbon monoxide containing small quantities of ethanol vapors are studied. Carbon monoxide was used to fix instable butyl cations in the form of corresponding acyl ions. Ester of α-methyl-butyric acid appears to be the only product of free butyl cation interaction with carbon monoxide in the presence of ethanol vapors. That means, that up to the moment of butyl cation reaction with carbon monoxide, the primary butyl cations are almost completely isomerized into secondary in agreement with results of previous investigations. This allows one to study free butyl cation isomerization process according to ion-molecular reaction product isomeric composition

Organophosphate esters in East Greenland polar bears and ringed seals: Adipose tissue concentrations and in vitro depletion and metabolite formation.

Science.gov (United States)

Strobel, Adelle; Willmore, William G; Sonne, Christian; Dietz, Rune; Letcher, Robert J

2018-04-01

East Greenland is a contamination "hot spot" for long-range transported anthropogenic chemicals, including organophosphate esters (OPEs). High concentrations of OPEs have been reported in arctic air while very little is known for wildlife where OPE tissue residues levels appear to be strongly influenced by biotransformation. In the present study, the hepatic in vitro metabolism of six environmentally relevant organophosphate (OP) triesters and corresponding OP diester formation were investigated in East Greenland polar bears (PBs) and ringed seals (RSs). The in vitro metabolism assay results were compared to adipose levels in field samples from the same individuals. In vitro OP triester metabolism was generally rapid and structure-dependent, where PBs metabolized OPEs more rapidly than RSs. Exceptions were the lack of triethyl phosphate (TEP) metabolism and slow metabolism of tris(2-ethylhexyl) phosphate (TEHP) in both species. OP diester metabolites were also formed with the exception of TEP which was not metabolized at all. Tris(1,3-dichloro-2-propyl) phosphate was completely converted to its corresponding diester. However, the mass balances showed that OP diester formation corresponding to TEHP, tri(n-butyl) phosphate, and tris(2-butyoxyethyl) phosphate did not account for 100% of the OP triester depletion, which indicated alternate pathways of OP triester metabolism had occurred. Triphenyl phosphate was completely converted to its OP diester metabolite in PBs but not in RSs suggesting species-specific differences. The results demonstrated that OP triester bioaccumulation and fate in PBs versus their RS prey is substantially influenced by biotransformation. Copyright © 2018 Elsevier Ltd. All rights reserved.

Exposure assessment of organophosphorus and organobromine flame retardants via indoor dust from elementary schools and domestic houses.

Science.gov (United States)

Mizouchi, Shigekazu; Ichiba, Masayoshi; Takigami, Hidetaka; Kajiwara, Natsuko; Takamuku, Toshiyuki; Miyajima, Toru; Kodama, Hiroki; Someya, Takashi; Ueno, Daisuke

2015-03-01

To assess the exposure of flame retardants (FRs) for school-children, organophosphorus flame retardants and plasticizers (PFRs) and organobromine flame retardants (BFRs) were determined in the indoor dust samples collected from elementary schools and domestic houses in Japan in 2009 and 2010. PFRs were detected in all the dust samples analyzed and the highest concentration of total PFRs was thousand-fold higher than that of BFRs. Among the PFRs, tris(butoxyethyl)phosphate (TBOEP) showed the highest concentration with a median (med.) of 270,000 ng g(-1) dry weight (3700-5,500,000 ng g(-1) dry weight), followed by tris(methylphenyl)phosphate (TMPPs)>triphenyl phosphate (TPHP)=tris(1,3-dichloro-2-propyl)phosphate (TDCIPP)=tris(2-chloroisopropyl)phosphate (TCIPP)=tris(2chloroethyl)phosphate (TCEP)>ethylhexyl diphenyl phosphate (EHDPP). Significantly higher concentrations of TBOEP, tri-n-butyl phosphate (TNBP), TPHP, TMPPs, and total-PFRs were found in dust samples from elementary schools than from domestic houses. It might be due to that higher concentrations of TBOEP (as leveling agent) were detected from the floor polisher/wax products collected in those elementary schools. On the other hand, significantly higher concentrations of TCEP, TCIPPs, and total chloroalkyl-PFRs were found in domestic houses than in elementary schools. Exposure assessments of PFRs via indoor dust from elementary schools and domestic houses were conducted by calculating the hazard quotient (HQ). Among PFRs, HQs for TBOEP exceeded 1 (higher than reference dose: RfD) and its highest value was 1.9. To reduce the intake of TBOEP by school-children, it is recommended that the use of floor polisher/wax containing TBOEP be reduced in schools. Copyright © 2014 Elsevier Ltd. All rights reserved.

Butyl Rubber: Compound Development and Characterization

National Research Council Canada - National Science Library

Sloan, James

2000-01-01

...), to develop the standard butyl rubber compound. The strategy of this work was to compound- and compression-mold high-quality, uniform butyl rubber experimental sheets and to evaluate their cure properties, mechanical properties...

Surfactant and counter-ion distribution in styrene-butyl acrylate-acrylic acid dry latex submonolayers

Directory of Open Access Journals (Sweden)

Keslarek Amauri José

2004-01-01

Full Text Available Styrene-butyl acrylate-acrylic acid latex submonolayers prepared using a non-reactive phosphate surfactant together with a reactive sulfonate surfactant were examined in a transmission microscope using electron energy loss spectroscopy imaging (ESI-TEM. Phosphorus is nearly absent from the particles core but it is detected in a thick shell and in unusual, strongly scattering structures with a low carbon content, and largely made out of inorganic phosphate. P is also dispersed outside the particles, while S is uniformly distributed within then. The Na and N elemental maps show that the respective monovalent ions (Na+ and NH4+ have different distributions, in the latex: Na signal within the particles is stronger than in the background, while N is accumulated at the particle borders. The distributions of surfactant and counter-ions are thus different from some current assumptions, but they support recent results on the distribution of ionic constituents in latex films, by scanning electric potential microscopy.

Chain Extension and Thermal Behavior of Recycled Poly(Ethylene Terephthalate Modified by Reactive Extrusion with Triphenyl Phosphite

Directory of Open Access Journals (Sweden)

Qin Dan

2016-01-01

Full Text Available Reactive extrusion experiments of recycled PET fabrics (R-PET were carried out in a Haake torque rheometer with triphenyl phosphite (TPP and thermal behavior of modified R-PET was investigated by differential scanning calorimetry (DSC. The reaction mechanism which TPP acts as a cross-linker is verified by the experiment of phosphorus elemental analysis. DSC results show the presence of reaction residues may not modify melting temperature Tm and crystallization temperature Tc is controlled by the combined effect of molecular weight and reaction residues.

Inhibition Effect of 1-Butyl-4-Methylpyridinium Tetrafluoroborate on the Corrosion of Copper in Phosphate Solutions

OpenAIRE

Scendo, M.; Uznanska, J.

2011-01-01

The influence of the concentration of 1-Butyl-4-methylpyridinium tetrafluoroborate (4MBPBF4) as ionic liquid (IL) on the corrosion of copper in 0.5 M P O 4 3 − solutions of pH 2 and 4 was studied. The research involved electrochemical polarization method, and scanning electron microscopy (SEM) technique. The results obtained showed that the inhibition efficiency of corrosion of copper increases with an increase in the concentration of 4MBPBF4 but decreases with increasing temperature. The the...

Organophosphate Ester Flame Retardants and Plasticizers in Ocean Sediments from the North Pacific to the Arctic Ocean.

Science.gov (United States)

Ma, Yuxin; Xie, Zhiyong; Lohmann, Rainer; Mi, Wenying; Gao, Guoping

2017-04-04

The presence of organophosphate ester (OPE) flame retardants and plasticizers in surface sediment from the North Pacific to Arctic Ocean was observed for the first time during the fourth National Arctic Research Expedition of China in the summer of 2010. The samples were analyzed for three halogenated OPEs [tris(2-chloroethyl) phosphate (TCEP), tris(1-chloro-2-propyl) phosphate (TCPP), and tris(dichloroisopropyl) phosphate], three alkylated OPEs [triisobutyl phosphate (TiBP), tri-n-butyl phosphate, and tripentyl phosphate], and triphenyl phosphate. Σ 7 OPEs (total concentration of the observed OPEs) was in the range of 159-4658 pg/g of dry weight. Halogenated OPEs were generally more abundant than the nonhalogenated OPEs; TCEP and TiBP dominated the overall concentrations. Except for that of the Bering Sea, Σ 7 OPEs values increased with increasing latitudes from Bering Strait to the Central Arctic Ocean, while the contributions of halogenated OPEs (typically TCEP and TCPP) to the total OPE profile also increased from the Bering Strait to the Central Arctic Ocean, indicating they are more likely to be transported to the remote Arctic. The median budget of 52 (range of 17-292) tons for Σ 7 OPEs in sediment from the Central Arctic Ocean represents only a very small amount of their total production volume, yet the amount of OPEs in Arctic Ocean sediment was significantly larger than the sum of polybrominated diphenyl ethers (PBDEs) in the sediment, indicating they are equally prone to long-range transport away from source regions. Given the increasing level of production and usage of OPEs as substitutes of PBDEs, OPEs will continue to accumulate in the remote Arctic.

Effects of prenatal triphenyl-tin exposure on the development of behavior and conditioned learning in rat pups.

Science.gov (United States)

Lehotzky, K; Szeberenyi, J M; Gonda, Z; Horkay, F; Kiss, A

1982-01-01

Neurotoxic effects of the fungicide triphenyl-tin acetate were examined in pups of mothers treated perorally on day 7-15 of gestation. The gait and development of motor coordination did not differ from those of control animals, in spite of the high mortality rate of control pups during the nursing period. Spontaneous locomotor activity of treated pups at the age of 23 and 36 days was increased, however by the age of 90 days activity returned to control levels. Conditioned avoidance was acquired more rapidly, but was also extinguished sooner in animals born from, the nursed by poisoned mothers than in control.

Turbine Engine Lubricant Reclamation.

Science.gov (United States)

1981-12-01

rt’s) as 4,4’-di-octyldiphenylamine (DODPA) or triphenyl phosphite (TPP), approximately 9.5-10 min; a peak corresponding to the rt’s of 3,7...TCP (tricresyl phosphate) - Kronitrex AA FMC 0.1% Ethyl antioxidant 703 - Ethyl Corp. 0.1% TPP (triphenyl phosphite ) - Eastman 0.1% Benzotriazole...will be an adsorption treatment to remove surfactants, trace metals, and other material that distilled over and was not removed during Ca(OH)2

Studies on the recovery of 233U from phosphate containing aqueous waste using DBDECMP as extractant

International Nuclear Information System (INIS)

Sagar, V.B.; Oak, M.S.; Pawar, S.M.; Sivaramakrishnan, C.K.; Patil, S.K.

1990-01-01

A method for the recovery and purification of 233 U from phosphate containing analytical waste is developed. Extraction studies with Di-butyl N,N-diethylcarbamoylmethylphosphonate (DBDECMP) in xylene were carried out to explore the feasibility of separation and purification of 233 U from such wastes. Based on the data obtained, optimum conditions for the recovery of 233 U are suggested. (author) 11 refs.; 1 fig.; 3 tabs

Intake of butylated hydroxyanisole and butylated hydroxytoluene and stomach cancer risk : results from analyses in the Netherlands : cohort study

NARCIS (Netherlands)

Botterweck, A.A.M.; Verhagen, H.; Goldbohm, R.A.; Kleinjans, J.; Brandt, P.A. van den

2000-01-01

Both carcinogenic and anticarcinogenic properties have been reported for the synthetic antioxidants butylated hydroxyanisole (BHA) and butylated hydroxytoluene (BHT). The association between dietary intake of BHA and BHT and stomach cancer risk was investigated in the Netherlands Cohort Study (NLCS)

Linear free energy relationships in heterogeneous catalysis--13. The dehydration of aliphatic alcohols over silica-alumina. [N-butyl alcohol, sec. -butyl or isopropyl alcohol, tert. -butyl alcolol

Energy Technology Data Exchange (ETDEWEB)

Take, J; Matsumoto, T; Yoneda, Y

1978-01-01

The dehydration of n-butyl alcohol at 120/sup 0/-166/sup 0/C, sec.-butyl or isopropyl alcohol at 100/sup 0/-145/sup 0/C, and tert.-butyl alcohol at 54/sup 0/-80/sup 0/C, over silica/alumina catalyst was zero order in alcohol at 0.01-0.1 atm, and the activation energies were 35.3, 31.7, 32.0, and 29.9 kcal/mol, respectively. The zero-order rate constants were mainly affected by the activation energies since the preexponential factors varied little except for tert.-butyl alcohol. A linear relationship was found between the activation energy or the logarithm of the zero-order rate constant and the heterolytic bond dissociation energy for the carbon-oxygen bond in alcohols D(R/sup +/OH/sup -/). The activation energy increased and the rate constant decreased with increasing D(R/sup +/OH/sup -/). The results indicate that dehydration is E1 over this catalyst, but a similar correlation was observed based on published data for dehydration over alumina, which follows an E2 mechanism, indicating that heterolytic cleavage of the C-O bond is rate-determining in both mechanisms.

Occurrence of Organophosphorus Flame Retardants and Plasticizers (PFRs) in Belgian Foodstuffs and Estimation of the Dietary Exposure of the Adult Population.

Science.gov (United States)

Poma, Giulia; Sales, Carlos; Bruyland, Bram; Christia, Christina; Goscinny, Séverine; Van Loco, Joris; Covaci, Adrian

2018-02-20

The occurrence of 14 organophosphorus flame retardants and plasticizers (PFRs) was investigated in 165 composite food samples purchased from the Belgian market and divided into 14 food categories, including fish, crustaceans, mussels, meat, milk, cheese, dessert, food for infants, fats and oils, grains, eggs, potatoes and derived products, other food (stocks), and vegetables. Seven PFRs [namely, tri-n-butyl phosphate (TnBP), tris(2-chloroethyl) phosphate (TCEP), tris(1-chloro-2-propyl) phosphate (TCIPP), tris(1,3-dichloro-2-propyl) phosphate (TDCIPP), triphenyl phosphate (TPHP), 2-ethylhexyldiphenyl phosphate (EHDPHP), and tris(2-ethylhexyl) phosphate (TEHP)] were detected at concentrations above quantification limits. Fats and oils were the most contaminated category, with a total PFR concentration of 84.4 ng/g of wet weight (ww), followed by grains (36.9 ng/g of ww) and cheese (20.1 ng/g of ww). Our results support the hypothesis that PFR contamination may occur during industrial processing and manipulation of food products (e.g., packaging, canning, drying, etc.). Considering the daily average intake of food for the modal adult Belgian (15-64 years of age), the dietary exposure to sum PFRs was estimated to be ≤7500 ± 1550 ng/day [103 ± 21 ng/kg of body weight (bw)/day]. For individual PFRs, TPHP contributed on average 3400 ng/day (46.6 ng/kg of bw/day), TCIPP 1350 ng/day (18.5 ng/kg of bw/day), and EHDPHP 1090 ng/day (15 ng/kg of bw/day), values that were lower than their corresponding health-based reference doses. The mean dietary exposure mainly originated from grains (39%), followed by fats and oils (21%) and dairy products (20%). No significant differences between the intakes of adult men and women were observed.

Investigation of antimony extraction from nitric acid solutions by tributyl phosphate

International Nuclear Information System (INIS)

Lakaev, V.S.; Smelov, V.S.

1988-01-01

The effect of iodide, hydrogen and pertechnetate ions on antimony extraction by tri-n-butyl phosphate (TBP) from aqueous nitric acid solutions under irradiated nuclear fuel processing is investigated at room temperature. The coefficients of antimony distribution are shown to increase at the presence of technetium ions 2-3 times and iodine ions - 100 and more times. Variation of hydrogen ion concentration does not affect antimony extraction. The schemes of the mechanism of antimony extraction at the pressence of iodide and pertechnetate ions are presented. Compositions of the formed compounds are given

Exposure to airborne organophosphates originating from hydraulic and turbine oils among aviation technicians and loaders.

Science.gov (United States)

Solbu, Kasper; Daae, Hanne Line; Thorud, Syvert; Ellingsen, Dag Gunnar; Lundanes, Elsa; Molander, Paal

2010-12-01

This study describes the potential for occupational exposure to organophosphates (OPs) originating from turbine and hydraulic oils, among ground personnel within the aviation industry. The OPs tri-n-butyl phosphate (TnBP), dibutyl phenyl phosphate (DBPP), triphenyl phosphate (TPP) and tricresyl phosphate (TCP) have been emphasized due to their use in such oils. Oil aerosol/vapor and total volatile organic compounds (tVOCs) in air were also determined. In total, 228 and 182 OPs and oil aerosol/vapor samples from technician and loader work tasks during work on 42 and 21 aircrafts, respectively, were collected in pairs. In general, the measured exposure levels were below the limit of quantification (LOQ) for 84%/98% (oil aerosol) and 82%/90% (TCP) of the samples collected during technician/loader work tasks. The air concentration ranges for all samples related to technician work were

Reactivity of tributyl phosphate degradation products with nitric acid: Relevance to the Tomsk-7 accident

International Nuclear Information System (INIS)

Barney, G.S.; Cooper, T.D.

1995-01-01

The reaction of a degraded tributyl phosphate (TBP) solvent with nitric acid is thought to have caused the chemical explosion at the Tomsk-7 reprocessing plant at Tomsk, Russia in 1993. The estimated temperature of the organic layer was not high eneough to cause significant reaction of nitric acid with TBP or hydrocarbon diluent compounds. A more reactive organic compound was likely present in the organic layer that reacted with sufficient heat generation to raise the temperature to the point where an autocatalytic oxidation of the organic solvent was initiated. Two of the most likely reactive compounds that are present in degraded TBP solvents are n-butanol and n-butyl nitrate. The reactions of these compounds with nitric acid are the subject of this study. The objective of laboratory-scale tests was to identify chemical reactions that occur when n-butanol and n-butyl nitrate contact heated nitric acid solutions. Reaction products were identified and quantitified, the temperatures at which these reactions occur and heats of reaction were measured, and reaction variables (temperature, nitric acid concentration, organic concentration, and reaction time) were evaluated. Data showed that n-butyl nitrate is less reactive than n-butanol. An essentially complete oxidation reaction of n-butanol at 110-120 C produced four major reaction products. Mass spectrometry identified the major inorganic oxidation products for both n-butanol and n-butyl nitrate as nitric oxide and carbon dioxide. Calculated heats of reaction for n-butanol and n-butyl nitrate to form propionic acid, a major reaction product, are -1860 cal/g n-butanol and -953 cal/g n-butyl nitrate. These heats of reaction are significant and could have raised the temperature of the organic layer in the Tomsk-7 tank to the point where autocatalytic oxidation of other organic compounds present resulted in an explosion

Gamma-radiation effect on thermal ageing of butyl rubber compounds

Energy Technology Data Exchange (ETDEWEB)

Scagliusi, Sandra R.; Cardoso, Elizabeth C.L.; Lugao, Ademar B., E-mail: srscagliusi@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2015-07-01

Butyl rubber has a comprehensive use in sealing systems, especially in tires inner tubes, due to their low permeability to gases. So, it is required that butyl rubber compounds show a better performance, more and more. Butyl rubber is provided with excellent mechanical properties and oxidation resistance. Besides showing these properties, radiation exposures impart modifications in physical-chemical and morphological properties on butyl rubber materials. When exposed to gamma-radiation, rubbers suffer changes in their mechanical and physical properties, caused by material degradation. The major radiation effect in butyl rubbers is chain scission; besides, ageing promotes too the same effect with further build-up of free radicals. This work aims to the study of gamma-radiation in physical-chemical properties of butyl rubber subjected to thermal ageing. Doses used herein were: 25 kGy, 50 kGy, 100 kGy, 150 kGy and 200 KGy. Samples were evaluated before and after ageing according to traditional essays, such as: hardness, tensile strength and elongation at break. From accomplished assessments it is possible to affirm that at doses higher than 50 kGy it was observed a sharp decreasing in butyl rubber physical-chemical properties, before and after exposure to ageing. (author)

Gamma-radiation effect on thermal ageing of butyl rubber compounds

International Nuclear Information System (INIS)

Scagliusi, Sandra R.; Cardoso, Elizabeth C.L.; Lugao, Ademar B.

2015-01-01

Butyl rubber has a comprehensive use in sealing systems, especially in tires inner tubes, due to their low permeability to gases. So, it is required that butyl rubber compounds show a better performance, more and more. Butyl rubber is provided with excellent mechanical properties and oxidation resistance. Besides showing these properties, radiation exposures impart modifications in physical-chemical and morphological properties on butyl rubber materials. When exposed to gamma-radiation, rubbers suffer changes in their mechanical and physical properties, caused by material degradation. The major radiation effect in butyl rubbers is chain scission; besides, ageing promotes too the same effect with further build-up of free radicals. This work aims to the study of gamma-radiation in physical-chemical properties of butyl rubber subjected to thermal ageing. Doses used herein were: 25 kGy, 50 kGy, 100 kGy, 150 kGy and 200 KGy. Samples were evaluated before and after ageing according to traditional essays, such as: hardness, tensile strength and elongation at break. From accomplished assessments it is possible to affirm that at doses higher than 50 kGy it was observed a sharp decreasing in butyl rubber physical-chemical properties, before and after exposure to ageing. (author)

Organic Semiconductors and Conductors with tert-Butyl Substituents

Directory of Open Access Journals (Sweden)

Toshiki Higashino

2012-08-01

Full Text Available Tetrathiafulvalene (TTF, pentacene, and quarterthiophene with tert-butyl substituents are synthesized, and the crystal structures and the transistor properties are investigated. The tetracyanoquinodimethane (TCNQ complex of tert-butyl TTF constructs highly one-dimensional segregated columns with tetragonal crystal symmetry.

[4,6-Dimethyl­pyrimidine-2(1H)-thione-κS]iodidobis(triphenyl­phosphane-κP)copper(I)

Science.gov (United States)

Pakawatchai, Chaveng; Wattanakanjana, Yupa; Choto, Patcharanan; Nimthong, Ruthairat

2012-01-01

In the mononuclear title complex, [CuI(C6H8N2S)(C18H15P)2], the CuI ion is in a slightly distorted tetra­hedral coordination geometry formed by two P atoms from two triphenyl­phosphane ligands, one S atom from a 4,6-dimethyl­pyrimidine-2(1H)-thione ligand and one iodide ion. There is an intra­molecular N—H⋯I hydrogen bond. In the crystal, π–π stacking inter­actions [centroid–centroid distance = 3.594 (1) Å] are observed. PMID:22719327

Butylated caffeic acid: An efficient novel antioxidant

Directory of Open Access Journals (Sweden)

G. Shi

2017-09-01

Full Text Available A novel antioxidant, butylated caffeic acid (BCA was rationally designed by adding a tert-butyl group to caffeic acid, which was synthesized at a high yield (36.2% from 2-methoxy-4-methylphenol by a four-step reaction including Friedel-Crafts alkylation, bromine oxidation, ether bond hydrolysis and Knoevenagel condensation. Its antioxidant capacity was much stronger than common commercial antioxidant tert-butyl hydroquinone (TBHQ and its mother compound, caffeic acid, in both rancimat and deep frying tests. When investigated via the DPPH method, the antioxidant capacity of BCA was almost equal to TBHQ, but lower than caffeic acid. BCA could be a potentially strong antioxidant, especially for food processing at high temperatures such as deep frying and baking.

Butylated caffeic acid: An efficient novel antioxidant

International Nuclear Information System (INIS)

Shi, G.; Liao, X.; Olajide, T.M.; Liu, J.; Jiang, X.; Weng, X.

2017-01-01

A novel antioxidant, butylated caffeic acid (BCA) was rationally designed by adding a tert-butyl group to caffeic acid, which was synthesized at a high yield (36.2%) from 2-methoxy-4-methylphenol (1) by a four-step reaction including Friedel-Crafts alkylation, bromine oxidation, ether bond hydrolysis and Knoevenagel condensation. Its antioxidant capacity was much stronger than common commercial antioxidant tert-butyl hydroquinone (TBHQ) and its mother compound, caffeic acid, in both rancimat and deep frying tests. When investigated via the DPPH method, the antioxidant capacity of BCA was almost equal to TBHQ, but lower than caffeic acid. BCA could be a potentially strong antioxidant, especially for food processing at high temperatures such as deep frying and baking. [es

Recovering/recycling of butyl and halogenated butyl rubber via ionizing radiation; Recuperacao/reciclagem de compostos de borrachas butilica e halobutilica por meio de radiacao ionizante

Energy Technology Data Exchange (ETDEWEB)

Martin, Sandra Regina Scagliusi

2013-07-01

Polymeric materials (plastics and rubbers) attain a continuous and raising proportion of urban and industrial scraps discarded in landfills; their impact on environment are more and more concerning. The implementation of new technologies in order to reduce impacts of plastic waste on the environment, at an effective cost, proved to be a great problem, due to inherent complexity for polymers re-using. Ionizing radiation is capable to modify structure and properties of polymeric material. Butyl and halobutyl rubbers have been used within a comprehensive scale, applications such as tires spare parts and diverse artifacts. The major high energy photon effect, as gamma-rays in butyl and halo butyl rubbers consists in free-radicals generation along changes in mechanical properties.This work aims to the development of controlled degradation processes (devulcanization) of butyl and halo butyl (chlorine and bromine) rubbers, in order to characterize their availability for transformation and modification of properties. Experimental results obtained showed that butyl and halobutyl rubbers,irradiated at 25 kGy and further sheared, are able to be used as an initial point for mixtures with pristine. (author)

Recycling of Gamma Irradiated Inner Tubes in Butyl Based Rubber Compound

International Nuclear Information System (INIS)

Karaagac, B.

2006-01-01

Crosslinked elastomeric materials, such as tyres are of great challenge concerning the environmental and ecological reasons. Ionizing radiation seems to offer unique opportunities to tackle the problem of recycling of polymers and rubbers on account of its ability to cause chain scission and/or cross-linking of polymeric materials. There is only limited amount of work reported on the irradiation-induced degradation of rubbers. Unlike the majority of the elastomers with high levels of unsaturation, butyl rubber exhibits significant degradation by ionizing radiation action. In this study, recycling of gamma irradiated inner tubes made of butyl rubber in butyl based rubber compounds was studied. Used inner tubes were irradiated with gamma rays in air at 100 and 120 kGy absorbed doses. The compatibility of irradiated inner tubes with virgin butyl rubber was first investigated. Gamma irradiated inner tube wastes were replaced with butyl rubber up to 15 phr in the compound recipe. Similar recipes were also prepared by using the same quantity of commercial butyl rubber crumbs devulcanized by conventional methods. The rheological and mechanical properties and carbon black dispersion degree for both types of compounds prepared by using inner tubes scraps and commercial butyl crumbs were measured and were compared to the values of virgin butyl rubber compound. It is well known that mechanical properties are deteriorated when rubber crumb is added to the virgin compound. It was observed that the decrease in the mechanical properties was much lower for the compounds prepared from the tubes irradiated at 120 kGy than irradiated at 100 kGy. The better mechanical properties were obtained for the compounds prepared by recycling of irradiated inner tubes at 120 kGy than the compounds prepared by using commercial butyl crumbs. Almost similar carbon black distributions were observed for the all compounds studied. It has been concluded that gamma irradiated inner tubes are compatible

Associations between urinary diphenyl phosphate and thyroid function.

Science.gov (United States)

Preston, Emma V; McClean, Michael D; Claus Henn, Birgit; Stapleton, Heather M; Braverman, Lewis E; Pearce, Elizabeth N; Makey, Colleen M; Webster, Thomas F

2017-04-01

Triphenyl phosphate (TPHP) is a commonly used organophosphate flame retardant and plasticizer with widespread human exposure. Data on health effects of TPHP are limited. Recent toxicological studies suggest TPHP may alter thyroid function. We used repeated measures to assess the temporal variability in urinary concentrations of the TPHP metabolite, diphenyl phosphate (DPHP), and to examine relationships between DPHP concentrations and thyroid hormones. We sampled 51 adults at months 1, 6, and 12 from 2010 to 2011. Urine samples were analyzed for DPHP. Serum samples were analyzed for free and total thyroxine (fT 4 , TT 4 ), total triiodothyronine (TT 3 ), and thyroid stimulating hormone (TSH). We assessed variability in DPHP using intraclass correlation coefficients (ICCs) and kappa statistics. We used linear mixed-effects models to examine associations between DPHP and thyroid hormones. DPHP was detected in 95% of urine samples. Mean DPHP concentrations were 43% higher in women than men. DPHP showed high within-subject variability (ICC range, 0.13-0.39; kappa range, 0.16-0.39). High versus low (≥2.65 vs. <2.65ng/mL) DPHP in all participants was associated with a 0.43μg/dL (95% confidence interval: 0.15, 0.72) increase in mean TT 4 levels. In sex-stratified analyses, high versus low DPHP was associated with a 0.91μg/dL (95% CI: 0.47, 1.36) increase in mean TT 4 in women. The association was attenuated in men (βeta=0.19; 95% CI: -0.15, 0.52). We found no significant associations between DPHP and fT 4 , TT 3 , or TSH. We found evidence that TPHP exposure may be associated with increased TT 4 levels, especially in women. Copyright © 2017 Elsevier Ltd. All rights reserved.

NMR analysis of t-butyl-catalyzed deuterium exchange at unactivated arene localities.

Science.gov (United States)

Stack, Douglas E; Eastman, Rachel

2016-10-01

Regioselective labelling of arene rings via electrophilic exchange is often dictated by the electronic environment caused by substituents present on the aromatic system. Previously, we observed the presence of a t-butyl group, either covalently bond or added as an external reagent, could impart deuterium exchange to the unactivated, C1-position of estrone. Here, we provide nuclear magnetic resonance analysis of this exchange in a solvent system composed of 50:50 trifluoroacetic acid and D 2 O with either 2-t-butylestrone or estrone in the presence of t-butyl alcohol has shed insights into the mechanism of this t-butyl-catalyzed exchange. Fast exchange of the t-butyl group concurrent with the gradual reduction of the H1 proton signal in both systems suggest a mechanism involving ipso attack of the t-butyl position by deuterium. The reversible addition/elimination of the t-butyl group activates the H1 proton towards exchange by a mechanism of t-butyl incorporation, H1 activation and exchange, followed by eventual t-butyl elimination. Density functional calculations are consistent with the observation of fast t-butyl exchange concurrent with slower H1 exchange. The σ-complex resulting from ipso attack of deuterium at the t-butyl carbon was 6.6 kcal/mol lower in energy than that of the σ-complex resulting from deuterium attack at C1. A better understanding of the t-butyl-catalyzed exchange could help in the design of labelling recipes for other phenolic metabolites. Copyright © 2016 The Authors. Journal of Labelled Compounds and Radiopharmaceuticals published by John Wiley & Sons, Ltd.

Inducing PLA/starch compatibility through butyl-etherification of waxy and high amylose starch.

Science.gov (United States)

Wokadala, Obiro Cuthbert; Emmambux, Naushad Mohammad; Ray, Suprakas Sinha

2014-11-04

In this study, waxy and high amylose starches were modified through butyl-etherification to facilitate compatibility with polylactide (PLA). Fourier transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy and wettability tests showed that hydrophobic butyl-etherified waxy and high amylose starches were obtained with degree of substitution values of 2.0 and 2.1, respectively. Differential scanning calorimetry, tensile testing, and scanning electron microscopy (SEM) demonstrated improved PLA/starch compatibility for both waxy and high amylose starch after butyl-etherification. The PLA/butyl-etherified waxy and high amylose starch composite films had higher tensile strength and elongation at break compared to PLA/non-butyl-etherified composite films. The morphological study using SEM showed that PLA/butyl-etherified waxy starch composites had a more homogenous microstructure compared to PLA/butyl-etherified high amylose starch composites. Thermogravimetric analysis showed that PLA/starch composite thermal stability decreased with starch butyl-etherification for both waxy and high amylose starches. This study mainly demonstrates that PLA/starch compatibility can be improved through starch butyl-etherification. Copyright © 2014 Elsevier Ltd. All rights reserved.

Separation of radio cesium from PUREX feed solution by sorption on composite ammonium molybdo phosphate (AMP)

International Nuclear Information System (INIS)

Singh, I.J.; Achuthan, P.V.; Jain, S.; Janardanan, C.; Gopalakrishnan, V.; Wattal, P.K.; Ramanujam, A.

2001-01-01

Composite AMP exchanger was developed and evaluated for separation of radio cesium from dissolver solutions of PUREX process using a column experiment. The composite shows excellent sorption of radio cesium from dissolver solutions without any loss of plutonium and uranium. The removal of radio cesium from dissolver solutions will help in lowering the degradation of tri-n-butyl phosphate (TBP) in the solvent extraction process and will also help in reducing the radiation related problems. (author)

and triorganotin(IV) complexes of 2-tert-butyl-4-methyl phenol

Indian Academy of Sciences (India)

TECS

-2-Me-4) have been synthesized by the reactions of di-n-butyl and dimethyltin dichlorides and tri-n-butyltin(IV) chloride with 2-tert-butyl-4-methylphenol and triethylamine in tetrahydrofuran. The reaction of triphenyltin chloride with trimethylsilyl-2-t-butyl-4- methylphenoxide in the same solvent however, gives a complex of ...

Organophosphate esters and phthalate esters in human hair from rural and urban areas, Chongqing, China: Concentrations, composition profiles and sources in comparison to street dust.

Science.gov (United States)

He, Ming-Jing; Lu, Jun-Feng; Ma, Jing-Ye; Wang, Huan; Du, Xiao-Fan

2018-06-01

Human hair and street dust from rural and urban areas in Chongqing were collected to analyze Organophosphate esters (OPEs) and phthalate esters (PAEs). Concentrations of OPEs in urban hair were significantly higher than those in rural hair, whereas PAEs concentrations in rural hair were significantly higher than those in urban hair. Different composition patterns of OPEs were observed in rural and urban hair, where tris (2-chloroisopropyl) phosphate (TCIPP), tris (butyl) phosphate (TNBP) and triphenyl phosphate (TPHP) were the dominating analogues in rural hair, accounting for 62.1% of the OPEs burden, and tris (methylphenyl) phosphate (TMPP) exhibited a high contribution in urban hair, responsible for 51.3% of total OPEs, which differed from the composition profiles in corresponding street dust. Analogous composition patterns of PAEs were found in hair of both areas. Di-(2-ethylhexyl) phthalate (DEHP), dibutyl phthalate (DNBP), diisobutyl phthalate (DIBP) and diethyl phthalate (DEP) were the most abundant analogues in hair samples, while DEHP was the predominant analogue in dust samples. No clear tendency was obtained between the increasing ages and the concentrations of both compounds. Most OPEs and PAEs congeners showed significantly positive correlation with one another in rural hair. On the contrary, different correlation patterns were observed in urban hair for OPEs and PAEs, indicating multiple or additional sources existed in urban areas. Significant correlations of OPEs and PAEs were found between hair and corresponding street dust samples, but poor correlations of OPEs and PAEs were observed between rural hair and rural indoor dust, suggesting that street dust may be a predominant exogenous source for human exposure to OPEs and PAEs in this area. Copyright © 2018 Elsevier Ltd. All rights reserved.

Solvent effects on the magnetic shielding of tertiary butyl alcohol

African Journals Online (AJOL)

)4 and tetramethyl ammonium cation N(CH3)4(+) have also been presented. KEY WORDS: Solvent effects, Magnetic shielding, Tertiary butyl alcohol, Tertiary butyl amine, Continuum solvation calculations, Chemical shift estimation methods

Synthesis of Poly (Butyl Methacrylate/Butyl Acrylate) Highly Absorptive Resin Using Glow Discharge Electrolysis

International Nuclear Information System (INIS)

Li Yan; Yao Mengqi; Liao Ruirui; Yang Wu; Gao Jinzhang; Ren Jie

2014-01-01

A highly absorptive resin poly (butyl methacrylate (BMA)-co-butyl acrylate (BA)) was prepared by emulsion polymerization, which was initiated by glow discharge electrolysis plasma (GDEP). The effects of discharge voltage, discharge time, monomer ratio and the amounts of cross-linking agent were examined and discussed in detail. The chemical structure of the obtained resin was characterized by means of attenuated total reflectance Fourier transform infrared spectroscopy, thermogravimetric analysis, and scanning electron microscopy. The optimal conditions were obtained as: discharge voltage was 600 V, discharge time was 8 min, the ratios of BMA:BA being 2:1 for chloroform and 3:1 for xylene, with 2% N, N'-methylenebis. Under optimal conditions, the oil absorbency was 70 g/g for chloroform and 46 g/g for xylene. Moreover, the absorptive dynamical behavior of the resulting resin was also investigated

Structure-dependent tuning of electro-optic and thermoplastic properties in triphenyl groups containing molecular glasses

Energy Technology Data Exchange (ETDEWEB)

Traskovskis, Kaspars, E-mail: kaspars.traskovskis@rtu.lv [Riga Technical University, Faculty of Materials Science and Applied Chemistry, 3/7 Paula Valdena Street, Riga LV-1048 (Latvia); Zarins, Elmars; Laipniece, Lauma [Riga Technical University, Faculty of Materials Science and Applied Chemistry, 3/7 Paula Valdena Street, Riga LV-1048 (Latvia); Tokmakovs, Andrejs [Institute of Solid State Physics, University of Latvia, 8 Kengaraga Street, Riga LV-1063 (Latvia); Kokars, Valdis [Riga Technical University, Faculty of Materials Science and Applied Chemistry, 3/7 Paula Valdena Street, Riga LV-1048 (Latvia); Rutkis, Martins [Institute of Solid State Physics, University of Latvia, 8 Kengaraga Street, Riga LV-1063 (Latvia)

2015-04-01

The series of seven molecular compounds composed of D–π–A chromophores and triphenylmethyl auxiliary groups were characterized by UV–Vis spectroscopy, differential scanning calorimetry and quantum chemical calculations. Nonlinear optical (NLO) properties of compounds were determined by second harmonic generation measurements in corona poled thin glassy films. The results show that triphenylmethyl auxiliary groups are effective at shielding undesirable dipole interactions in solid phase thus increasing NLO efficiency of materials. Thermal stability up to 108 °C was achieved for a polar order in poled samples. - Highlights: • Triphenylmethyl groups can be used to reduce solid phase dipole interactions in organic molecular materials. • NLO efficiency of a poled material is higher, if a number of present triphenyl groups increases. • NLO efficiency of materials decreases, if polarity of used chromophores increases. • Thermal stability of polar order up to 108 °C can be achieved in poled organic glasses.

Catalytic oxidation of butyl acetate over silver-loaded zeolites

International Nuclear Information System (INIS)

Wong, Cheng Teng; Abdullah, Ahmad Zuhairi; Bhatia, Subhash

2008-01-01

The performance of silver-loaded zeolite (HY and HZSM-5) catalysts in the oxidation of butyl acetate as a model volatile organic compound (VOC) was studied. The objective was to find a catalyst with superior activity, selectivity towards deep oxidation product and stability. The catalyst activity was measured under excess oxygen condition in a packed bed reactor operated at gas hourly space velocity (GHSV) = 15,000-32,000 h -1 , reaction temperature between 150 and 500 deg. C and butyl acetate inlet concentration of 1000-4000 ppm. Both AgY and AgZSM-5 catalysts exhibited high activity in the oxidation of butyl acetate. Despite lower silver content, AgY showed better activity, attributed to better metal dispersion, surface characteristics and acidity, and its pore system. Total conversion of butyl acetate was achieved at above 400 deg. C. The oxidation of butyl acetate followed a simple power law model. The reaction orders, n and m were evaluated under differential mode by varying the VOC partial pressure between 0.004 and 0.018 atm and partial pressure of oxygen between 0.05 and 0.20 atm. The reaction rate was independent of oxygen concentration and single order with respect to VOC concentration. The activation energies were 19.78 kJ/mol for AgY and 32.26 kJ/mol for AgZSM-5, respectively

Method for producing redox shuttles

Science.gov (United States)

Pupek, Krzysztof Z.; Dzwiniel, Trevor L.; Krumdick, Gregory K.

2015-03-03

A single step method for producing a redox shuttle having the formula 2,5-di-tert-butyl-1,4-phenylene tetraethyl bis(phosphate) is provided, the method comprising phosphorylating tert butyl hydroquinone with a phosphate-containing reagent. Also provided is method for producing 2,5-di-tert-butyl-1,4-phenylene tetraethyl bis(phosphate), the method comprising solubilizing tert-butyl hydroquinone and tetrabutylammonium bromide with methyltetrahydrofuran to create a mixture; heating the mixture while adding base to the mixture in an amount to turn the mixture orange; and adding diethyl chlorophosphate to the orange mixture in an amount to phosphorylate the hydroquinone.

Some studies on the extraction of plutonium from phosphate containing nitric acid solutions using DBDECMP as extractant

International Nuclear Information System (INIS)

Sagar, V.B.; Oak, M.S.; Pawar, S.M.; Sivaramakrishnan, C.K.; Patil, S.K.

1991-01-01

Extraction studies have been carried out to explore the feasibility of separation of Pu(IV) from phosphate containing analytical wastes generated in the laboratory. Distribution data on the extraction of Pu(IV) from DBDECMP (di-butyl,N,N-diethylcarbamoyl methyl phosphonate) in xylene an aqueous nitric acid and its mixture with sulfuric as well as with sulfuric and phosphoric acids were obtained. Based on the data obtained, the conditions for the recovery of plutonium from such water solutions are suggested. (author) 7 refs.; 1 fig.; 3 tabs

Simultaneous analysis of tert-butylhydroquinone, tert-butylquinone, butylated hydroxytoluene, 2-tert-butyl-4-hydroxyanisole, 3-tert-butyl-4-hydroxyanisole, α-tocopherol, γ-tocopherol, and δ-tocopherol in edible oils by normal-phase high performance liquid chromatography.

Science.gov (United States)

Li, Jun; Bi, Yanlan; Sun, Shangde; Peng, Dan

2017-11-01

A normal-phase high performance liquid chromatography method for the simultaneous determination of tert-butylhydroquinone, tert-butylquinone, butylated hydroxytoluene, 2-tert-butyl-4-hydroxyanisole, 3-tert-butyl-4-hydroxyanisole, α-tocopherol, γ-tocopherol, and δ-tocopherol in edible oils was investigated. A silica column was used to separate the analytes with the gradient elution. An ultraviolet-visible detector was set at dual wavelengths mode (280 and 310nm). The column temperature was 30°C. The analytes were directly extracted with methanol. Results showed that the normal-phase high performance liquid chromatography method performed well with wide liner ranges (0.10∼500.00μg/mL, R 2 >0.9998), low limits of detection and quantitation (below 0.40 and 1.21μg/mL, respectively), and good recoveries (81.38∼102.34% in soybean oils and 83.03∼100.79% in lard, respectively). The reduction of tert-butylquinone caused by the reverse-phase high performance liquid chromatography during the injection was avoided with the current normal-phase method. The two isomers of butylated hydroxyanisole can also be separated with good resolution. Copyright © 2017 Elsevier Ltd. All rights reserved.

Synthesis of 4-tert-butyl-1,1-dimethylindan and 7-tert-Butyl-3,3-dimethyl-1-indanone and a comparison of isomers

International Nuclear Information System (INIS)

Eisenbraun, E.J.; Harms, W.M.; Paraniswamy, V.A.; Chen, H.H.; Porcaro, P.J.; Wood, T.F.; Chien, M.

1982-01-01

4-tert-Butyl-1,1-dimethylindan was synthesized to help establish the identity of products (5- and 6-tert-butyl-1,1-dimethylindan as minor and major products, respectively) from the sulfuric acid catalyzed condensation of tert-butylbenzene and isoprene. NMR ( 1 H and 13 C) studies of these hydrocarbons and their corresponding indanones, obtained through chromic acid oxidation, provided structural proof. Gated decoupling experiments were crucial to complete assignment

High energy radiation effects on mechanical properties of butyl rubber compounds

International Nuclear Information System (INIS)

Pozenato, Cristina A.; Scagliusi, Sandra R.; Cardoso, Elisabeth C.L.; Lugao, Ademar B.

2013-01-01

The high energy radiation on butyl rubber compounds causes a number of chemical reactions that occur after initial ionization and excitation events. These reactions lead to changes in molecular mass of the polymer through scission and crosslinking of the molecules, being able to affect the physical and mechanical properties. Butyl rubber has excellent mechanical properties and oxidation resistance as well as low gas and water vapor permeability. Due to all these properties butyl rubber is widely used industrially and particularly in tires manufacturing. In accordance with various authors, the major effect of high energy, such as gamma rays in butyl rubber, is the yielding of free-radicals along with changes in mechanical properties. There were evaluated effects imparted from high energy radiation on mechanical properties of butyl rubber compounds, non-irradiated and irradiated with 25 kGy, 50 kGy, 150 kGy and 200 kGy. It was also observed a sharp reducing in stress rupture and elongation at break for doses higher than 50 kGy, pointing toward changes in polymeric chain along build-up of free radicals and consequent degradation. (author)

Preparation of candidate reference materials for the determination of phosphorus containing flame retardants in styrene-based polymers.

Science.gov (United States)

Roth, Thomas; Urpi Bertran, Raquel; Latza, Andreas; Andörfer-Lang, Katrin; Hügelschäffer, Claudia; Pöhlein, Manfred; Puchta, Ralph; Placht, Christian; Maid, Harald; Bauer, Walter; van Eldik, Rudi

2015-04-01

Candidate reference materials (RM) for the analysis of phosphorus-based flame retardants in styrene-based polymers were prepared using a self-made mini-extruder. Due to legal requirements of the current restriction for the use of certain hazardous substances in electrical and electronic equipment, focus now is placed on phosphorus-based flame retardants instead of the brominated kind. Newly developed analytical methods for the first-mentioned substances also require RMs similar to industrial samples for validation and verification purposes. Hence, the prepared candidate RMs contained resorcinol-bis-(diphenyl phosphate), bisphenol A bis(diphenyl phosphate), triphenyl phosphate and triphenyl phosphine oxide as phosphorus-based flame retardants. Blends of polycarbonate and acrylonitrile-co-butadiene-co-styrene as well as blends of high-impact polystyrene and polyphenylene oxide were chosen as carrier polymers. Homogeneity and thermal stability of the candidate RMs were investigated. Results showed that the candidate RMs were comparable to the available industrial materials. Measurements by ICP/OES, FTIR and NMR confirmed the expected concentrations of the flame retardants and proved that analyte loss and degradation, respectively, was below the uncertainty of measurement during the extrusion process. Thus, the candidate RMs were found to be suitable for laboratory use.

The study of DNA adduct 8-hydroxy-2‧deoxyguanosine (8-OHdG) formation of butylated hydroxyanisole (BHA) and its metabolite ter-butyl hydroquinone (TBHQ) through in vitro reaction with Calf Thymus DNA and 2‧deoxyguanosine

Science.gov (United States)

Budiawan; Purwaningsih, S. S.; Cahaya, D. I.

2017-04-01

Butylated Hydroxyanisole (BHA) and its metabolite Tert-Butyl Hydroquinone (TBHQ) are synthetic antioxidants, commonly used as food and beverage preservatives. Although WHO declared their safety, the use of these preservatives are still controversial because some studies showed that BHA induced proliferative effects in animal testing and TBHQ is considered as carcinogenic and causes DNA cleavage. This study is aimed to analyze the interaction between Calf Thymus DNA with BHA and TBHQ which are mediated with Copper (II) Chloride. The result of the study in spectrophotometric showed there was bathochromic shift as much as 2-3 nm in DNA treated with TBHQ. The next analysis used HPLC method in stationary phase of ODS, mobile phase of 10mM Natrium Hydrogen Phosphate Buffer and Methanol (85 : 15) for DNA adduct formation, 8-Hydroxy-2-Deoxyguanosine (8-OHDG) as biomarker of risk cancer. The resultof the study showed the formation of DNA adduct 8-OHDG in the interaction between DNA and 20-500 ppm of TBHQ. The 8-OHdG formation was greatly increased by the higher concentration of TBHQ. The relative amount of 8 OHDG which formed was reached 946/105 deoxyguanosine in DNA bases. Confirmation test by LCMS/MS was characterized with the detection of mother ion peak (m/z 284); fragment ion peaks at m/z 167.9, and 139.9; at retention time 3.52 min. Meanwhile the interaction between DNA and 50-250 ppm BHA did not induce 8-OHDG.

A comparison of the effect of intranasal desmopressin and intramuscular hyoscine N-butyl bromide combination with intramuscular hyoscine N-butyl bromide alone in acute renal colic

Directory of Open Access Journals (Sweden)

Abdol-Reza Kheirollahi

2010-01-01

Full Text Available Background: Patients with acute renal colic usually require immediate diagnosis and treatment. In this clinical trial analgesic effect of hyoscine N-butyl bromide and desmopressin combination in comparison with hyoscine N-butyl bromide alone in patients with acute renal colic induced by urinary stones was assessed. Methods: The study included 114 patients randomly allocated in two groups (A and B. Patients in group A received 20 mg intramuscular hyoscine N-butyl bromide at admission time and patients in group B received 20 μg of intranasal desmopressin in combination with 20 mg intramuscular hyoscine N-butyl bromide. A visual analogue scale (VAS; a 10-cm horizontal scale ranging from "zero or no pain" to "10 or unbearable pain" was hired to assess the patients′ pain severity at baseline, 30 and 60 minutes after the treatments. Results: On admission, the pain level was similar in both groups (group A: 8.95 ± 0.11 and group B: 8.95 ± 0.12. In group A, the mean of pain level showed a decrease after 30 minutes (group A: 7.26 ± 0.25 and group B: 5.95 ± 0.28 but further decreasing did not occur; however in group B, the pain consistently decreased and the mean after 60 minutes was significantly decreased (group A: 6.80 ± 0.31 and group B: 3.71 ± 0.31. No side effects were detected in this study. Conclusions: The combination of hyoscine N-butyl bromide and desmopressin is more effective than hyoscine N-butyl bromide alone in patients with renal colic. Further studies are recommended to validate these findings and compare the different doses of desmopressin.

Impact of di-n-butyl phthalate on reproductive system development in European pikeperch (Sander lucioperca

Directory of Open Access Journals (Sweden)

Sylwia Jarmołowicz

2013-01-01

Full Text Available Phthalic acid, di-n-butyl ester known as di-n-butyl phthalate, is an organic chemical compound that belongs to the group of endocrine disruptor compounds that have a documented negative impact on mammalian endocrine systems. Di-n-butyl phthalate is used widely as a plasticizer in the manufacture of artificial materials, which is why it is found in all types of environmental samples including those from water basins. The aim of the study was to describe the impact of di-n-butyl phthalate on the development of the reproductive system of European pikeperch (Sander lucioperca during the sex differentiation period (age 61–96 days post hatch. A total of 240 fish were divided into 6 groups (40 fish per tank. Treatments consisted of a control group (0 g di-n-butyl phthalate·kg-1 feed and five trial groups with 0.125, 0.25, 0.5, 1, and 2 g di-n-butyl phthalate·kg-1 feed, respectively. Histological changes of the fish gonads, sex ratio, survival and growth of fish were evaluated. Di-n-butyl phthalate seriously disturbed sex differentiation process of pikeperch. Histopathological analyses revealed that the administration of 2 g di-n-butyl phthalate·kg-1 significantly affected the sex ratio. The feminization process (intersex gonads at concentrations of 1 g and 2 g di-n-butyl phthalate·kg-1 were observed. All analyzed concentrations delayed testicular development. Phthalate did not have a significant impact on the survival or growth rates of the pikeperch. This is the first report of disruption sex differentiation processes in fish by di-n-butyl phthalate.

Structures of butyl ions formed by electron impact ionization of isomeric butyl halides and alkanes

International Nuclear Information System (INIS)

Shold, D.M.; Ausloos, P.

1978-01-01

Using a pulsed ion cyclotron resonance (ICR) spectrometer, it is demonstrated that at pressures of about 10 -6 Torr and at observation times ranging from 10 -3 to 0.5 s, isobutane, neopentane, 2,2-dimethylbutane, isobutyl halides, and tert-butyl halides form C 4 H 9 + ions having the tertiary structure. In n-alkanes, 2-methylbutane, 3-methylpentane, n-butyl halides, and sec-butyl halides, both sec-C 4 H 9 + and t-C 4 H 9 + ions are observed, the sec-C 4 H 9 + ions surviving without rearrangement for at least 0.1 s. However, in the case of the halides, a collision-induced isomerization of the sec-C 4 H 9 + to the t-C 4 H 9 + ions occurs. The efficiency of this process increases with the basicity of the alkyl halide. Radiolysis experiments carried out at atmospheric pressures indicate, in agreement with ICR and solution experiments, that at times as short as 10 -10 s the majority of the i-C 4 H 9 + ions from isobutyl bromide rearrange to the t-C 4 H 9 + structure. On the other hand, in the radiolysis of both n-hexane and 3-methylpentane, the abundance of t-C 4 H 9 + relative to sec-C 4 H 9 + is substantially smaller than that observed in the ICR experiments, and decreases with decreasing collision interval. It is suggested that about 90% of the i-C 4 H 9 + can rearrange to t-C 4 H 9 + by simple 1,2-hydride shift without involving secondary or protonated methylcyclopropane structures as intermediates. 4 figures, 2 tables

76 FR 77709 - Butyl acrylate-methacrylic acid-styrene polymer; Tolerance Exemption

Science.gov (United States)

2011-12-14

...This regulation establishes an exemption from the requirement of a tolerance for residues of 2-Propenoic acid, 2-methyl-, polymer with butyl 2-propenoate and ethenylbenzene (CAS Reg. No. 25036-16-2); also known as butyl acrylate-methacrylic acid-styrene polymer when used as an inert ingredient in a pesticide chemical formulation. Momentive Performance Materials submitted a petition to EPA under the Federal Food, Drug, and Cosmetic Act (FFDCA), requesting an exemption from the requirement of a tolerance. This regulation eliminates the need to establish a maximum permissible level for residues of 2-Propenoic acid, 2-methyl-, polymer with butyl 2-propenoate and ethenylbenzene on food or feed commodities.

APPLICATION OF PHOTOCATALYTIC PROCESS FOR REMOVAL OF METHYL TERT-BUTYL ETHER FROM HIGHLYCONTAMINATED WATER

Directory of Open Access Journals (Sweden)

A. Mesdaghinia

2007-09-01

Full Text Available The oxygenate methyl tert-butyl ether is added to gasoline to increase the octane level and to reduce carbon monoxide and hydrocarbon emissions by vehicles. The high mobility, water solubility, and resistance to natural attenuation associated with methyl tert-butyl ether may result in contamination of ground and surface waters. In this research the degradation of aqueous methyl tert-butyl ether at relatively high concentrations was investigated by UV-vis/TiO2/H2O2 photocatalytic process. The effect of important operational parameters such as pH, amount of H2O2, catalyst loading, and irradiation time were also studied. Concentrations of methyl tert-butyl ether and intermediates such as tert-butyl formate and tert-butyl alcohol were measured over a 180 min period using a gas chromatograph equipped with flame ionization detector and combined with headspace sampler. Results showed that the time required for complete degradation increased from 30 to 180min, when the initial concentration was increased from 10 to 500mg/L. The first order rate constant for degradation of methyl tert-butyl ether from the hydroxyl radical was estimated to be 0.177 to 0.022 1/min as the concentration increased from 10 to 500mg/L. Study on the overall mineralization monitored by total organic carbon (TOC analysis showed that in the initial concentration of 100mg/L methyl tert-butyl ether, complete mineralization was obtained after 110min under UV-vis/TiO2/H2O2 photocatalytic process.

A comparison of the interfacial tension of tri-iso-amyl phosphate and tri-n-butyl phosphate

International Nuclear Information System (INIS)

Sreenivasulu, B.; Rajeswari, S.; Suresh, A.; Antony, M.P.; Sivaraman, N.

2016-01-01

In our recent studies, Tri-iso-amyl Phosphate (TiAP) was found to be a potential extractant for fast reactor fuel reprocessing. It has excellent extraction characteristics, higher capacity to load Pu(IV) without third phase formation, lower aqueous solubility etc. Mixer-Settler runs with TiAP showed excellent extraction and stripping behavior of uranium and plutonium. Physiochemical properties are considered to be important parameters for a solvent to be qualified for the processing of spent nuclear fuels. Prior to the deployment of TiAP in a reprocessing plant, it is necessary to measure the interfacial tension of TiAP. The present study deals with the measurement of interfacial tension (G/IFT) of neat and 1.1M solutions of TiAP and TBP in n-dodecane (DD) (degraded and undegraded solvents). The samples were irradiated in a 60 Co gamma chamber with a dose rate of 5 kGy/hr. IFT of neat and 1.1M solutions of TiAP and TBP in n-DD were measured against 4M HNO 3 at 303K by Drop weight method in which G is given by G = (V´ (r aq - r org ) ´ g) / (2 ´ p ´ r ´ f s ), where f s is the Smith's correction factor, f s = (1 - r/R), V is the volume of the drop at the moment of separation, r aq and r org are the densities of the aqueous and the organic phases, respectively, r is the radius at the capillary tip, R is the drop radius at the moment of separation and g is the acceleration due to gravity. Results indicate that IFT of neat TiAP-HNO 3 system (11.2) is marginally lower than that of 1.1M TiAP/DD-HNO 3 system

Isothermal (vapor + liquid) equilibria and excess enthalpy data of {1-hexene + methyl butyl ether (MBE)} and {1-hexene + methyl tert-butyl ether (MTBE)} binary systems at several temperatures

International Nuclear Information System (INIS)

Hani, Rachida; Solimando, Roland; Negadi, Latifa; Jose, Jacques; Ait Kaci, Ahmed

2012-01-01

Highlights: ► Vapor pressures of (1-hexene + methyl butyl ether) or (1-hexene + methyl tert-butyl ether) are reported between (263 and 363) K. ► The two mixtures exhibit positive G E . ► Additionally, molar excess enthalpies, H E , for the two binary systems have been measured at 303.15. - Abstract: The vapor pressures of {1-hexene + methyl butyl ether (MBE)} and {1-hexene + methyl tert-butyl ether (MTBE)} binary mixtures and of the three pure components were measured by means of a static device at temperatures between (263 and 333) K. The data were correlated with the Antoine equation. From these data, excess Gibbs functions were calculated for several constant temperatures and fitted to a third-order Redlich–Kister equation using the Barker’s method. Additionally, molar excess enthalpies, H E , for the two binary systems have been measured at 303.15 K using an isothermal flow calorimeter.

Conversion of Lignocellulosic Biomass to Ethanol and Butyl Acrylate

Energy Technology Data Exchange (ETDEWEB)

Binder, Thomas [Archer Daniels Midland Company, Decatur, IL (United States); Erpelding, Michael [Archer Daniels Midland Company, Decatur, IL (United States); Schmid, Josef [Archer Daniels Midland Company, Decatur, IL (United States); Chin, Andrew [Archer Daniels Midland Company, Decatur, IL (United States); Sammons, Rhea [Archer Daniels Midland Company, Decatur, IL (United States); Rockafellow, Erin [Archer Daniels Midland Company, Decatur, IL (United States)

2015-04-10

Conversion of Lignocellulosic Biomass to Ethanol and Butyl Acrylate. The purpose of Archer Daniels Midlands Integrated Biorefinery (IBR) was to demonstrate a modified acetosolv process on corn stover. It would show the fractionation of crop residue to distinct fractions of cellulose, hemicellulose, and lignin. The cellulose and hemicellulose fractions would be further converted to ethanol as the primary product and a fraction of the sugars would be catalytically converted to acrylic acid, with butyl acrylate the final product. These primary steps have been demonstrated.

Amended final report on the safety assessment of PPG-40 butyl ether with an addendum to include PPG-2, -4, -5, -9, -12, -14, -15, -16, -17, -18, -20, -22, -24, -26, -30, -33, -52, and -53 butyl ethers.

Science.gov (United States)

Lanigan, R S

2001-01-01

The Polypropylene Glycol (PPG) Butyl Ethers function as skinand hair-conditioning agents in cosmetics. Intestinal absorption of the PPG Butyl Ethers was inversely proportional to the molecular weight. In general, the toxicity of the PPG Butyl Ethers decreased as the molecular weight increased. In acute studies, moderate intraperitoneal (IP) doses of various PPG Butyl Ethers caused convulsive seizures in mice and anesthetized dogs, and large oral doses caused decreased activity, anuria, renal tubular swelling and necrosis, and hepatic swelling and necrosis. PPG-2 Butyl Ether vapors were nontoxic by the inhalation route. PPG-2 Butyl Ether was nontoxic in short-term feeding and dermal exposure studies in rats. In animal irritation studies, PPG-2 Butyl Ether caused minor, transient erythema and desquamation; in addition, erythema, edema, ecchymosis, necrosis, and other changes were observed during an acute percutaneous study. PPG-2 Butyl Ether also caused minor to moderate conjunctival irritation and minor corneal injury. PPG-2 Butyl Ether when dermally applied was nontoxic to pregnant rats and was nonteratogenic at doses up to 1.0 ml/kg/day. PPG BE800 at concentrations of 0.001% to 0.26% in feed was noncarcinogenic to rats after 2 years of treatment. In clinical studies, PPG BE800 was nonirritating and nonsensitizing to the skin when tested using 200 subjects. PPG-40 Butyl Ether was neither an irritant nor a sensitizer in a repeat-insult patch test using 112 subjects. Although clinical testing did not indicate significant skin irritation is produced by these ingredients, the animal test data did indicate the potential that these ingredients can be irritating. Therefore, it was concluded that the PPG Butyl Ethers can be used safely in cosmetic products if they are formulated to avoid irritation. Data on the component ingredients, Propylene Glycol, PPG, and n-Butyl Alcohol, from previous cosmetic ingredient safety assessments were also considered and found to support

Temporary diplopia upon hyoscine-N-butyl bromide administration: case report

Directory of Open Access Journals (Sweden)

Migliorini R

2013-05-01

Full Text Available R Migliorini, R Malagola, M Mafrici, R Spena, L ArricoDepartment of Sense Organs, University of Rome "La Sapienza", Rome, ItalyAbstract: Hyoscine-N-butyl bromide is a widely used antispasmodic belonging to the belladonna alkaloid class of semisynthetic quaternary ammonium compounds. These compounds exert a spasmolytic action on the smooth muscles of the bile-gastrointestinal tract, genitourinary tract, salivary glands (xerostomia, and also on the visual apparatus – in particular, the irido-ciliary complex. As a consequence, they provoke collateral effects such as mydriasis and accommodation disturbances. We report the case of a 23-year-old woman who complained of not only "dry mouth" but also "cloudy vision" and a "diplopia", both of temporary type, 2 hours after oral administration of hyoscine-N-butyl bromide.Keywords: hyoscine-N-butyl bromide, accommodation disorders, temporary diplopia, fusion alteration, vertical strabismus

Preparation and characterization of emulsifier-free polyphenylsilsesquioxane-poly (styrene–butyl acrylate) hybrid particles

Energy Technology Data Exchange (ETDEWEB)

Bai, Ruiqin; Qiu, Teng, E-mail: qiuteng@mail.buct.edu.cn; Han, Feng; He, Lifan; Li, Xiaoyu, E-mail: lixy@mail.buct.edu.cn

2013-10-01

The core–shell polyphenylsilsesquioxane-poly (styrene–butyl acrylate) hybrid latex paticles with polyphenylsilsesquioxane as core and poly (styrene–butyl acrylate) as shell were successfully synthesized by seeded emulsion polymerization using polyphenylsisesquioxane (PPSQ) latex particles as seeds. X-ray diffraction (XRD) indicated that the polyphenylsilsesquioxane (PPSQ) had ladder structure, and PPSQ had incorporated into the hybrid latex particles. Transmission electron microscopy (TEM) confirmed that the resultant hybrid latex particles had the core–shell structure. TEM and dynamic light scattering (DLS) analysis indicated that the polyphenylsisesquioxane latex particles and obtained core–shell hybrid latex particles were uniform and possessed narrow size distributions. X-ray photoelectron spectroscopy (XPS) analysis also indicated that the PPSQ core particles were enwrapped by the polymer shell. In addition, compared with pure poly (styrene–butyl acrylate) latex film, the polyphenylsilsesquioxane-poly (styrene–butyl acrylate) hybrid latex film exhibited lower water uptake, higher pencil hardness and better thermal stability.

Physicochemical properties and radiolytic degradation studies on tri-iso-amyl phosphate (TiAP)

Energy Technology Data Exchange (ETDEWEB)

Sreenivasulu, B.; Sivaraman, Nagarajan [Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India). Homi Bhabha National Inst.; Suresh, A.; Rajeswari, S.; Ramanathan, N.; Antony, M.P.; Joseph, M. [Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India). Chemistry Group

2017-06-01

The solvent composed of tri-iso-amyl phosphate (TiAP) in n-dodecane (n-DD) is regarded as a promising candidate for reprocessing of spent fuel. In this context, the radiolytic degradation of a solution of TiAP in n-dodecane was investigated by irradiating the solvent to various absorbed dose levels of γ-radiation. The neat extractant or a solution of extractant in n-dodecane was irradiated in the presence of nitric acid. Physicochemical properties such as density, viscosity and interfacial tension (IFT) were measured for unirradiated and irradiated solutions. The extent of degradation was determined by measuring the variation in extraction behavior of U(VI) and Pu(IV) with irradiated solvent systems. Uranium and plutonium retention with irradiated solvents was also measured. The distribution ratio of uranium and plutonium increased with increase in absorbed dose. Effect of alpha degradation was studied by plutonium retention as a function of time using 1.1 M TiAP/n-DD. Laser desorption/ionization mass spectrometric technique was employed to identify the possible radiolytic degradation products. Similar studies were also carried out with tri-n-butyl phosphate (TBP) based solvent system under identical experimental conditions and the results are compared.

Multiprobe Spectroscopic Inverstigation of Molecular-level Behavior within Aqueous 1-Butyl-3-methylimidazolium Tetrafluoroborate

Energy Technology Data Exchange (ETDEWEB)

Sarkar, Abhra [Indian Institute of Technology, Delhi; Ali, Maroof [Indian Institute of Technology, Delhi; Baker, Gary A [ORNL; Tetin, Sergey Y. [Abbott Laboratories; Ruan, Qiaoqiao [Abbott Laboratories; Pandey, Siddharth [Indian Institute of Technology, Delhi

2009-01-01

In this work, an array of molecular-level solvent featuressincluding solute-solvent/solvent-solvent interactions, dipolarity, heterogeneity, dynamics, probe accessibility, and diffusionswere investigated across the entire composition of ambient mixtures containing the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate, [bmim][BF4], and pH 7.0 phosphate buffer, based on results assembled for nine different molecular probes utilized in a range of spectroscopic modes. These studies uncovered interesting and unusual solvatochromic probe behavior within this benchmark mixture. Solvatochromic absorbance probessa watersoluble betaine dye (betaine dye 33), N,N-diethyl-4-nitroaniline, and 4-nitroanilineswere employed to determine ET (a blend of dipolarity/polarizability and hydrogen bond donor contributions) and the Kamlet-Taft indices * (dipolarity/polarizability), R (hydrogen bond donor acidity), and (hydrogen bond acceptor basicity) characterizing the [bmim][BF4] + phosphate buffer system. These parameters each showed a marked deviation from ideality, suggesting selective solvation of the individual probe solutes by [bmim][BF4]. Similar conclusions were derived from the responses of the fluorescent polarity-sensitive probes pyrene and pyrene-1-carboxaldehyde. Importantly, the fluorescent microfluidity probe 1,3-bis(1-pyrenyl)propane senses a microviscosity within the mixture that significantly exceeds expectations derived from simple interpolation of the behavior in the neat solvents. On the basis of results from this probe, a correlation between microviscosity and bulk viscosity was established; pronounced solvent-solvent hydrogen-bonding interactions were implicit in this behavior. The greatest deviation from ideal additive behavior for the probes studied herein was consistently observed to occur in the buffer-rich regime. Nitromethane-based fluorescence quenching of pyrene within the [bmim][BF4] + phosphate buffer system showed unusual compliance with a sphere

Final report of the addendum to the safety assessment of n-butyl alcohol as used in cosmetics.

Science.gov (United States)

McLain, Valerie C

2008-01-01

n-Butyl Alcohol is a primary aliphatic alcohol historically used as a solvent in nail care cosmetic products, but new concentration of use data indicate that it also is being used at low concentrations in eye makeup, personal hygiene, and shaving cosmetic products. n-Butyl Alcohol has been generally recognized as safe for use as a flavoring substance in food and appears on the 1982 Food and Drug Administration (FDA) list of inactive ingredients for approved prescription drug products. n-Butyl Alcohol can be absorbed through the skin, lungs, and gastrointestinal tract. n-Butyl Alcohol may be formed by hydrolysis of butyl acetate in the blood, but is rapidly oxidized. The single oral dose LD(50) of n-Butyl Alcohol for rats was 0.79 to 4.36 g/kg. The dermal LD(50) for rabbits was 4.2 g/kg. Inhalation toxicity studies in humans demonstrate sensory irritation of the upper respiratory tract, but only at levels above 3000 mg/m(3). Animal studies demonstrate intoxication, restlessness, ataxia, prostration, and narcosis. Exposures of rats to levels up to 4000 ppm failed to produce hearing defects. High concentrations of n-Butyl Alcohol vapors can be fatal. Ocular irritation was observed for n-Butyl alcohol at 0.005 ml of a 40% solution. The behavioral no-effect dose for n-Butyl Alcohol injected subcutaneously (s.c.) was 120 mg/kg. Fetotoxicity has been demonstrated, but only at maternally toxic levels (1000 mg/kg). No significant behavioral or neurochemical effects were seen in offspring following either maternal or paternal exposure to 3000 or 6000 ppm. n-Butyl Alcohol was not mutagenic in Ames tests, did not induce sister-chromatid exchange or chromosome breakage in chick embryos or Chinese hamster ovary cells, did not induce micronuclei formation in V79 Chinese hamster cells, did not have any chromosome-damaging effects in a mouse micronucleus test, and did not impair chromosome distribution in the course of mitosis. Clinical testing of n-Butyl Alcohol for

Thermodynamic properties of 4-tert-butyl-diphenyl oxide

International Nuclear Information System (INIS)

Druzhinina, A.I.; Pimenova, S.M.; Tarazanov, S.V.; Nesterova, T.N.; Varushchenko, R.M.

2015-01-01

Highlights: • The sample of the 4-tert-butyl-diphenyl oxide was synthesized and purified. • Heat capacities, energy of combustion, saturation vapor pressures were measured. • The temperature, the enthalpy and the entropy of fusion were determined. • The enthalpy of sublimation at T = 298.15 K was derived. • The main thermodynamic functions and functions of formation were computed. - Abstract: The main thermodynamic functions (changes of the entropy, enthalpy, and Gibbs free energy) and functions of formation at T = 298.15 K of 4-tert-butyl-diphenyl oxide in condensed and ideal gas states were computed on the basis of experimental results obtained. The heat capacities of 4-tert-butyl-diphenyl oxide was measured by vacuum adiabatic calorimetry over the temperature range (8 to 371) K. The temperature, the enthalpy and the entropy of fusion were determined. The energy of combustion of the sample was determined by static-bomb combustion calorimetry. The saturation vapor pressures of the substance were measured by dynamic transpiration method over the temperature and pressure intervals (298 to 325) K and (0.05 to 1.2) Pa. The enthalpy of sublimation at T = 298.15 K was derived. The contribution of O-(2C b ) group (where C b is the carbon atom in a benzene ring) into the absolute entropies of diphenyl oxide derivatives was assessed

Solvent free lipase catalyzed synthesis of butyl caprylate

Indian Academy of Sciences (India)

MEERA T SOSE

2017-11-10

Nov 10, 2017 ... Department of Chemical Engineering, Institute of Chemical Technology, Matunga (E), ... study for the synthesis of butyl caprylate in presence of bio-catalyst. ..... −1 with Thermomyces lanuginosus lipase.26 The relation.

Synthetic phenolic antioxidants, including butylated hydroxytoluene (BHT), in resin-based dental sealants

Energy Technology Data Exchange (ETDEWEB)

Wang, Wei; Kannan, Pranav; Xue, Jingchuan [Wadsworth Center, New York State Department of Health, and Department of Environmental Health Sciences, School of Public Health, State University of New York at Albany, Empire State Plaza, P.O. Box 509, Albany, NY 12201-0509 (United States); Kannan, Kurunthachalam, E-mail: Kurunthachalam.kannan@health.ny.gov [Wadsworth Center, New York State Department of Health, and Department of Environmental Health Sciences, School of Public Health, State University of New York at Albany, Empire State Plaza, P.O. Box 509, Albany, NY 12201-0509 (United States); Biochemistry Department, Faculty of Science, Experimental Biochemistry Unit, King Fahd Medical Research Center, King Abdulaziz University, Jeddah (Saudi Arabia)

2016-11-15

Resin-based dental sealants (also referred to as pit-and-fissure sealants) have been studied for their contribution to bisphenol A (BPA) exposure in children. Nevertheless, little attention has been paid to the occurrence of other potentially toxic chemicals in dental sealants. In this study, the occurrence of six synthetic phenolic antioxidants (SPAs), including 2,6-di-tert-butyl-4-hydroxytoluene (BHT), 2,6-di-tert-butyl-4-(hydroxyethyl)phenol (BHT-OH), 3,5-di-tert-butyl-4-hydroxy-benzaldehyde (BHT-CHO), 2,6-di-tert-butylcyclohexa-2,5-diene-1,4-dione (BHT-Q), 3,5-di-tert-butyl-4-hydroxybenzoic acid (BHT-COOH) and 2-tert-butyl-4-methoxyphenol (BHA), was examined in 63 dental sealant products purchased from the U.S. market. BHT was found in all dental sealants at median and maximum concentrations of 56.8 and 1020 µg/g, respectively. The metabolites of BHT and BHA were detected in 39–67% of samples, at concentration ranges of butyl-4-hydroxytoluene (BHT) concentration of up to 1020 µg/g was found. • Estimated daily intake of BHT after sealant placement was up to 9.52 µg/kg bw/d. • Daily intake of BHT through dental sealant application was below the acceptable daily intake.

Synthetic phenolic antioxidants, including butylated hydroxytoluene (BHT), in resin-based dental sealants

International Nuclear Information System (INIS)

Wang, Wei; Kannan, Pranav; Xue, Jingchuan; Kannan, Kurunthachalam

2016-01-01

Resin-based dental sealants (also referred to as pit-and-fissure sealants) have been studied for their contribution to bisphenol A (BPA) exposure in children. Nevertheless, little attention has been paid to the occurrence of other potentially toxic chemicals in dental sealants. In this study, the occurrence of six synthetic phenolic antioxidants (SPAs), including 2,6-di-tert-butyl-4-hydroxytoluene (BHT), 2,6-di-tert-butyl-4-(hydroxyethyl)phenol (BHT-OH), 3,5-di-tert-butyl-4-hydroxy-benzaldehyde (BHT-CHO), 2,6-di-tert-butylcyclohexa-2,5-diene-1,4-dione (BHT-Q), 3,5-di-tert-butyl-4-hydroxybenzoic acid (BHT-COOH) and 2-tert-butyl-4-methoxyphenol (BHA), was examined in 63 dental sealant products purchased from the U.S. market. BHT was found in all dental sealants at median and maximum concentrations of 56.8 and 1020 µg/g, respectively. The metabolites of BHT and BHA were detected in 39–67% of samples, at concentration ranges of butyl-4-hydroxytoluene (BHT) concentration of up to 1020 µg/g was found. • Estimated daily intake of BHT after sealant placement was up to 9.52 µg/kg bw/d. • Daily intake of BHT through dental sealant application was below the acceptable daily intake.

Double-Balloon-Assisted n-Butyl-2-Cyanoacrylate Embolization of Intrahepatic Arterioportal Shunt Prior to Chemoembolization of Hepatocellular Carcinoma

Energy Technology Data Exchange (ETDEWEB)

Takao, Hidemasa, E-mail: takaoh-tky@umin.ac.jp; Shibata, Eisuke; Ohtomo, Kuni [University of Tokyo, Department of Radiology, Graduate School of Medicine (Japan)

2016-10-15

A case of multiple hepatocellular carcinomas with a severe intrahepatic arterioportal shunt that was successfully embolized with n-butyl-2-cyanoacrylate with coaxial double-balloon occlusion prior to transcatheter arterial chemoembolization is presented. A proximal balloon positioned at the proper hepatic artery was used for flow control, and a coaxial microballoon, positioned in the closest of three arterial feeding branches to the arterioportal shunt, was used to control the delivery of n-butyl-2-cyanoacrylate. This coaxial double-balloon technique can prevent proximal embolization and distal migration of n-butyl-2-cyanoacrylate and enable precise control of the distribution of n-butyl-2-cyanoacrylate. It could also be applicable to n-butyl-2-cyanoacrylate embolization for other than intrahepatic arterioportal shunt.

Anaerobic degradation of methyl tert-butyl ether (MTBE) and tert-butyl alcohol (TBA).

Science.gov (United States)

Finneran, K T; Lovley, D R

2001-05-01

The potential for anaerobic degradation of methyl tert-butyl ether (MTBE) and tert-butyl alcohol (TBA) was investigated in laboratory incubations of sediments from a petroleum-contaminated aquifer and in aquatic sediments. The addition of humic substances (HS) stimulated the anaerobic degradation of MTBE in aquifer sediments in which Fe(III) was available as an electron acceptor. This is attributed to the fact that HS and other extracellular quinones can stimulate the activity of Fe(III)-reducing microorganisms by acting as an electron shuttle between Fe(III)-reducing microorganisms and insoluble Fe(III) oxides. MTBE was not degraded in aquifer sediments without Fe(III) and HS. [14C]-MTBE added to aquatic sediments adapted for anaerobic MTBE degradation was converted to 14CO2 in the presence or absence of HS or the HS analog, anthraquione-2,6-disulfonate. Unamended aquatic sediments produced 14CH4 as well as 14CO2 from [14C]-MTBE. The aquatic sediments also rapidly consumed TBA under anaerobic conditions and converted [14C]-TBA to 14CH4 and 14CO2. An adaptation period of ca. 250-300 days was required prior to the most rapid anaerobic MTBE degradation in both sediment types, whereas TBA was metabolized in the aquatic sediments without a lag. These results demonstrate that, under the appropriate conditions, MTBE and TBA can be degraded in the absence of oxygen. This suggests that it may be possible to design strategies for the anaerobic remediation of MTBE in petroleum-contaminated subsurface environments.

Stereosequence distributions of poly(t-butyl methacrylate)s prepared with butyllithium

International Nuclear Information System (INIS)

Suzuki, Toshimitsu; Yamada, Osamu; Watanabe, Yoshihisa; Takegami, Yoshinobu

1982-01-01

13 C NMR spectra of poly(t-butyl methacrylate)s (PBMA) prepared with butyl-lithium (n-BuLi) were studied. Methylene carbon resonances appeared as five overlapped peaks, which were interpreted as a combination of hexad stereosequence distributions. The stereosequence distribution of PBMA prepared with n-BuLi at -78 0 C obeyed the first order Markov chain model even polymerized in tetrahydrofuran (THF). Syndiotactic PBMA was obtained with azobisisobutyronitrile (AIBN) as the initiator, and the stereosequence distribution of this polymer agreed well with Bernoullian statistics. (author)

27 CFR 21.101 - tert-Butyl alcohol.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false tert-Butyl alcohol. 21.101 Section 21.101 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS FORMULAS FOR DENATURED ALCOHOL AND RUM Specifications for Denaturants § 21...

27 CFR 21.100 - n-Butyl alcohol.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false n-Butyl alcohol. 21.100 Section 21.100 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS FORMULAS FOR DENATURED ALCOHOL AND RUM Specifications for Denaturants § 21...

Effect of electron beam irradiation on the structural properties of poly(vinyl alcohol) formulations with triphenyl tetrazolium chloride dye (TTC)

Science.gov (United States)

Ali, Z. I.; Said, Hossam M.; Ali, H. E.

2006-01-01

Films of poly(vinyl alcohol) (PVA) composites with triphenyl tetrazolium chloride (TTC) dye were prepared and exposed to various radiation doses delivered by accelerated electrons. The results showed that at a low dose of 50 kGy, the colour difference (Δ E*) of PVA/TTC films was increased by ˜10 times of the initial value. However, the change in colour differences did not go systematically with increasing the TTC content, in which the composite with 1.5 wt% displayed higher value than that with 3.5 wt%. The differential scanning calorimetry (DSC) showed that the presence of the TTC dye caused a depression in the melting point ( Tm) and heat of fusion (Δ Hf) of the PVA bulk polymer. However, the thermogravimetric analysis (TGA) showed that the presence of the TTC dye improved the thermal stability of PVA. Also, the tensile strength at break of PVA/TTC composites was improved after electron beam irradiation.

Polymerization behavior of butyl bis(hydroxymethyl)phosphine oxide ...

Indian Academy of Sciences (India)

lenovo

Polymerization behavior of butyl bis(hydroxymethyl)phosphine oxide: Phosphorus containing polyethers for. Li‒ion conductivities. Heeralal Vignesh Babu, Billakanti Srinivas and Krishnamurthi Muralidharan*. School of Chemistry, University of Hyderabad, Hyderabad - 500046, India. Table of Contents. TGA plots of SPE2.

Study on the effect of gamma radiolysis on the chromatographic composition profile of tri-isoAmyl-phosphate-n-dodecane-nitric acid system

International Nuclear Information System (INIS)

Chaudhary, S.D.; Lokhande, Manisha; Bindu, M.; Tripathi, S.C.; Gandhi, P.M.

2013-01-01

Tri-Iso-Amyl phosphate (TiAP), a higher homologue of tri-butyl phosphate (TBP) is the solvent proposed for the reprocessing of the spent nuclear fuel of Fast Breeder Reactors (FBR) origin. TiAP-n-dodecane has extraction behavior comparable to that of TBP-n-dodecane system, without third phase formation and an aqueous solubility ∼ 19mg/L, that is far too less in case as compared to that with TBP(∼400gm/L). We have initiated our study to examine the radiolytic degradation behavior of TiAP-n-dodecane in comparison to that of TBP and explore its full potential for reprocessing of spent nuclear fuels. A 30% mixture of TiAP with n-dodecane equilibrated with nitric acid of concentrations 2M has been subjected to steady state gamma radiolysis using 60 Co source. The samples were irradiated for increasing absorbed dose of 6,12 and 18M rad. Each of these samples were subjected to gas chromatographic analysis under optimised condition using thermal conductivity detector. Separately, these samples were also methylated using diazomethane for the determination of acidic phosphate species as their volatile methyl ester

Proof of concept for molecular velcro based on the attractive interaction between porphyrin and pyridine containing copolymers

Directory of Open Access Journals (Sweden)

M. Sievers

2018-06-01

Full Text Available In this short communication, we investigated the synthesis and mixing of porphyrin and pyridine functionalized copolymers as a proof of concept for a velcro-like interaction. A functionalized porphyrin monomer with one polymerizable side chain was synthesized following a rational synthetic pathway. Subsequent copolymerization and careful removal of residual free porphyrin led to poly(n-butyl acrylate-co-5,10,15-triphenyl-20-(3-vinylphenylporphyrin. The immobilized porphyrin was transformed into the corresponding zinc(II complex, which is capable of the coordinative binding of one pyridine moiety. Complete metallation was proven by absorption spectroscopy. 4-Vinylpyridine was immobilized by copolymerization with n-butyl acrylate, too. Via controlled radical polymerization conditions, the molecular weight of poly(n-butyl acrylate-co-4-vinylpyridine was limited to one tenth of the molecular weight of the porphyrin containing copolymer. This large difference in the molecular weight easily allowed identifying the polymers in the mixture of both. With the help of diffusion ordered nuclear magnetic resonance spectroscopy, the complete and temperature-stable precipitation of the porphyrin containing copolymer was observed, proving the expected attractive interaction and supramolecular network formation.

Subchronic toxicity studies of t-butyl alcohol in rats and mice.

Science.gov (United States)

Lindamood, C; Farnell, D R; Giles, H D; Prejean, J D; Collins, J J; Takahashi, K; Maronpot, R R

1992-07-01

The purpose of this study was to evaluate the toxicity of t-butyl alcohol, an important commodity chemical, an additive to unleaded gasoline, and a contaminant of drinking water. Ninety-day toxicity studies were conducted in B6C3F1 mice and Fischer 344 (F344) rats of both sexes using dosed water. Dose levels of t-butyl alcohol were 0, 0.25, 0.5, 1, 2, and 4% (w/v). Lethality was observed at the 4% level of both sexes and species. Weight-gain depression was present in all dose levels of male rats; 4% female rats; 1, 2, and 4% male mice; and 2 and 4% female mice. Water consumption was increased at lower dose levels in male rats and decreased in the higher dose levels of both sexes of rats and female mice. Clinical signs in rats were ataxia in both sexes and hypoactivity in males. Clinical signs in mice were ataxia, abnormal posture, and hypoactivity. In rats, urine volumes were reduced, in association with crystalluria. Gross lesions at necropsy were urinary tract calculi, renal pelvic and ureteral dilatation, and thickening of the urinary bladder mucosa. Microscopic lesions were hyperplasia of transitional epithelia and inflammation of the urinary bladder. In male rats treated with t-butyl alcohol, microscopic renal changes were suggestive of alpha-2 mu-globulin nephropathy. No-effect levels for the urinary tract lesions were 1% in male rats and mice (803.7 mg/kg/day for the male rats and 1565.8 mg/kg/day for the male mice) and 2% in female rats and mice (1451.5 mg/kg/day for the female rats and 4362.9 mg/kg/day for the female mice). The results indicate that in rodents the urinary tract is the target organ for t-butyl alcohol toxicity, and males are more sensitive to t-butyl alcohol toxicity than females.

Radiation crosslinking of poly(butyl acrylate) during polymerization and grafted copolymerization with Cr(III) crosslinked collagen

International Nuclear Information System (INIS)

Pietrucha, K.; Kroh, J.

1984-01-01

Enhanced crosslinking of synthetic polymer simultaneous with grafting and homopolymerization processes have been observed in irradiated leather tanned with Cr(III) and embedded with aqueous emulsions of butyl acrylate. Extent of poly(butyl acrylate) crosslinking during copolymerization was found to be approximately one order higher than in the case of radiation polymerization of butyl acrylate in emulsion. New method for isolation of grafted copolymer based on degradation of collagen has been developed. The extent of crosslinking was calculated from the swelling data. (author)

EFFECTS OF STIMULATOR SUBSTANCES ON AEROBIC METHYL TERT-BUTYL ETHER BIODEGRADATION BY MICROBIAL CONSORTIUM

Directory of Open Access Journals (Sweden)

M. Farrokhi ، S. Ahmadizad

2009-04-01

Full Text Available In this study dissolved humic substances and yeast extract were tested in different concentrations for enhancing methyl tert-butyl ether mineralization by isolated microorganisms from a variety of sources. All experiments were conducted at a constant temperature of 25ºC. Vials of 50 mL and 125 mL volume sealed with Teflon-lined Mini-Nert caps was used for microcosm experiments. In all experiments 1% sodium azide were used as control. Samples of bacterial cultures that metabolize methyl tert-butyl ether have been analysed by direct GC analysis using flame ionization detector. Cultures able to metabolize have been found in activated sludge and soils. These microorganisms weregram-positive bacterium. An aerobic microbial consortium was enriched in laboratory for four months. Methyl tert-butyl ether has been shown to biodegrade under aerobic and co-metabolic conditions. A microbial consortium isolated from activated sludges was identified as Cocobacillus. The concentration of the initial attached biomass was about 0.11 g/L of dry weight. The maximum mineralization rate and beneficial effects of stimulator substances on aerobic biodegradation of methyl tert-butyl ether occurred with the culture by combined concentrations of 500 mg/L of yeast extract and 20 mg/L of peat humic growth support of microbial consortium within 216 h and in presence of high oxygen levels and well mixing conditions. It was shown that adding, peat humic and yeast extract together, had better stimulatory effect on methyl tert-butyl ether biodegradation. Results clearly showed a stimulatory effect on methyl tert-butyl ether consumption higher than 20%. Consortium was capable of degrading concentrations of ≤1000 mg/L, whereas concentrations of >1000 mg/L, were not degraded.

Reaction of biscyclopentadienyl molybdendihalides with tert.-butyl hydroperoxide and its using for cyclohexene epoxidation

International Nuclear Information System (INIS)

Aleksandrov, Yu.A.; Fomin, V.M.; Kolmakov, A.O.

1983-01-01

As a result of reactions of biscyclopentadienyl molybden-dihalides (Cp 2 MoX 2 , X=Cl, Br or I) with tert.-butyl hydroperoxide, tert.-butylperoxides of biscyclopentadienyl molybdendichloride and-dibromide are synthesized for the first time, which are characterized by physico-chemical properties. Cyclohexene in the reaction mixture of Cp 2 MoX 2 with tert -butyl hydroperoxide is oxidated to form cyclohexene oxide, the reaction proceeding at a high rate and with a quantitative yield. Tert.-butylperoxide of biscyclopentadienyl molybdendihalide is responsible for the cyclohexene epoxidation reaction. The schemes for the mechanism of Cp 2 MoX 2 reactions with tert.-butyl hydroperoxide in the absence and presence of olefine are suggested

Atom transfer radical polymerization of n-butyl acrylate catalyzed by atom transfer radical polymerization of n-butyl acrylate catalyzed by

NARCIS (Netherlands)

Zhang, H.; Linde, van der R.

2002-01-01

The homogeneous atom transfer radical polymerization (ATRP) of n-butyl acrylate with CuBr/N-(n-hexyl)-2-pyridylmethanimine as a catalyst and ethyl 2-bromoisobutyrate as an initiator was investigated. The kinetic plots of ln([M]0/[M]) versus the reaction time for the ATRP systems in different

Radiation crosslinking of poly(butyl acrylate) during polymerization and grafted copolymerization with Cr(III) crosslinked collagen

International Nuclear Information System (INIS)

Pietrucha, K.; Kroh, J.

1986-01-01

Enhanced crosslinking of synthetic polymer simultaneously with grafting and homopolymerization processes has been observed in irradiated leather tanned with Cr(III) and embedded with aqueous emulsions of butyl acrylate. The extent of poly(butyl acrylate) crosslinking during copolymerization was found to be approximately one order higher than in the case of radiation polymerization of butyl acrylate in emulsion. A new method for isolation of grafted copolymer based on degradation of collagen has been developed. The extent of crosslinking was calculated from the swelling data. (author)

Method for determination of methyl tert-butyl ether and its degradation products in water

Science.gov (United States)

Church, C.D.; Isabelle, L.M.; Pankow, J.F.; Rose, D.L.; Tratnyek, P.G.

1997-01-01

An analytical method is described that can detect the major alkyl ether compounds that are used as gasoline oxygenates (methyl tert-butyl ether, MTBE; ethyl tert-butyl ether, ETBE; and tert-amyl methyl ether, TAME) and their most characteristic degradation products (tert-butyl alcohol, TBA; tert-butyl formate, TBF; and tert-amyl alcohol, TAA) in water at sub-ppb concentrations. The new method involves gas chromatography (GC) with direct aqueous injection (DAI) onto a polar column via a splitless injector, coupled with detection by mass spectrometry (MS). DAI-GC/MS gives excellent agreement with conventional purge-and-trap methods for MTBE over a wide range of environmentally relevant concentrations. The new method can also give simultaneous identification of polar compounds that might occur as degradation products of gasoline oxygenates, such as TBA, TBF, TAA, methyl acetate, and acetone. When the method was applied to effluent from a column microcosm prepared with core material from an urban site in New Jersey, conversion of MTBE to TBA was observed after a lag period of 35 days. However, to date, analyses of water samples from six field sites using the DAI-GC/MS method have not produced evidence for the expected products of in situ degradation of MTBE.An analytical method is described that can detect the major alkyl ether compounds that are used as gasoline oxygenates (methyl tert-butyl ether, MTBE; ethyl tert-butyl ether, ETBE; and tert-amyl methyl ether, TAME) and their most characteristic degradation products (tert-butyl alcohol, TBA; tert-butyl formate, TBF; and tert-amyl alcohol, TAA) in water at sub-ppb concentrations. The new method involves gas chromatography (GC) with direct aqueous injection (DAI) onto a polar column via a splitless injector, coupled with detection by mass spectrometry (MS). DAI-GC/MS gives excellent agreement with conventional purge-and-trap methods for MTBE over a wide range of environmentally relevant concentrations. The new method

Synthesis of Highly Porous Poly(tert-butyl acrylate)-b-polysulfone-b-poly(tert-butyl acrylate) Asymmetric Membranes

KAUST Repository

Xie, Yihui; Moreno Chaparro, Nicolas; Calo, Victor M.; Cheng, Hong; Hong, Pei-Ying; Sougrat, Rachid; Behzad, Ali Reza; Tayouo Djinsu, Russell; Nunes, Suzana Pereira

2016-01-01

For the first time, self-assembly and non-solvent induced phase separation was applied to polysulfone-based linear block copolymers, reaching mechanical stability much higher than other block copolymers membranes used in this method, which were mainly based on polystyrene blocks. Poly(tert-butyl acrylate)-b-polysulfone-b-poly(tert-butyl acrylate) (PtBA30k-b-PSU14k-b-PtBA30k) with a low polydispersity of 1.4 was synthesized by combining step-growth condensation and RAFT polymerization. Various advanced electron microscopies revealed that PtBA30k-b-PSU14k-b-PtBA30k assembles into worm-like cylindrical micelles in DMAc and adopts a “flower-like” arrangement with the PSU central block forming the shell. Computational modeling described the mechanism of micelle formation and morphological transition. Asymmetric nanostructured membranes were obtained with a highly porous interconnected skin layer and a sublayer with finger-like macrovoids. Ultrafiltration tests confirmed a water permeance of 555 L m-2 h-1 bar-1 with molecular weight cut-off of 28 kg/mol. PtBA segments on the membrane surface were then hydrolyzed and complexed with metals, leading to cross-linking and enhancement of antibacterial capability.

Synthesis of Highly Porous Poly(tert-butyl acrylate)-b-polysulfone-b-poly(tert-butyl acrylate) Asymmetric Membranes

KAUST Repository

Xie, Yihui

2016-03-24

For the first time, self-assembly and non-solvent induced phase separation was applied to polysulfone-based linear block copolymers, reaching mechanical stability much higher than other block copolymers membranes used in this method, which were mainly based on polystyrene blocks. Poly(tert-butyl acrylate)-b-polysulfone-b-poly(tert-butyl acrylate) (PtBA30k-b-PSU14k-b-PtBA30k) with a low polydispersity of 1.4 was synthesized by combining step-growth condensation and RAFT polymerization. Various advanced electron microscopies revealed that PtBA30k-b-PSU14k-b-PtBA30k assembles into worm-like cylindrical micelles in DMAc and adopts a “flower-like” arrangement with the PSU central block forming the shell. Computational modeling described the mechanism of micelle formation and morphological transition. Asymmetric nanostructured membranes were obtained with a highly porous interconnected skin layer and a sublayer with finger-like macrovoids. Ultrafiltration tests confirmed a water permeance of 555 L m-2 h-1 bar-1 with molecular weight cut-off of 28 kg/mol. PtBA segments on the membrane surface were then hydrolyzed and complexed with metals, leading to cross-linking and enhancement of antibacterial capability.

Metabolism of the fungicide Denmert (S-n-butyl S'-p-tert-butyl-benzyl N-3-pyridyldithiocarbonimidate, S-1358) and Denmert sulfoxides in liver enzyme systems

International Nuclear Information System (INIS)

Ohkawa, Hideo; Okihara, Yukiko; Miyamoto, Junshi

1976-01-01

On incubation with rat liver microsomes plus MADPH, Denmert (S-n-butyl S'-p-tert-butylbenzyl N-3-pyridyldithiocarbonimidate) underwent at least two different types of oxidation; hydroxylation and sulfoxidation. Hydroxylation of Denmert at the tert-butyl group was one of the major metabolic attacks in mammalian metabolism. Sulfoxidation of Denmert gave two isomers of Denmert sulfoxides which were intermediates in the metabolism and readily transformed into 2-(3'-pyridylimino)-4-carboxylthiazolidine (HM) in the presence of L-cysteine without enzymatic mediation. This type of conjugation with cysteine appears to be a new class of metabolic reactions in mammals. Denmert S-oxide showed increased fungicidal activity when assayed in liquid cultures, but not on plant leaves. (auth.)

Solvent-free sample preparation by headspace solid-phase microextraction applied to the tracing of n-butyl nitrite abuse.

Science.gov (United States)

Tytgat, J; Daenens, P

1996-01-01

The most common alkyl nitrites encountered in forensic toxicology are iso-butyl, n-butyl and iso-pentyl(amyl) nitrites. All have become popular as an aphrodisiac, especially among the homosexual population. Alkyl nitrites are a volatile and unstable group of compounds, which hydrolyse in aqueous matrices to the alcohol and nitrite ion. Here we describe a fast, clean and sensitive procedure for the detection of hydrolysed n-butyl nitrite in whole human blood using a new, solvent-free sampling technique, the headspace solid-phase micro-extraction (HSPME), combined with GC/FID analysis. Sample preparation was investigated using two different stationary phases (100 microns polydimethylsiloxane and 85 microns polyacrylate), coating a fused silica fibre. The effect of different sampling times at fixed temperatures was also studied. Our results demonstrate that the HSPME/GC/FID procedure allows tracing of n-butyl nitrite abuse and detects hydrolysed n-butyl nitrite, i.e., released n-butanol, in whole blood at the 1 ng/mL level.

Diisobutyl phthalate has comparable anti-androgenic effects to di-n-butyl phthalate in fetal rat testis

DEFF Research Database (Denmark)

Boberg, Julie; Petersen, Marta Axelstad; Vinggaard, Anne

2006-01-01

Phthalates are widely used as plasticizers in various consumer products and building materials. Some of the phthalates are known to interfere with male reproductive development in rats, and di-n-butyl phthalate (DBP), diethylhexyl phthalate (DEHP) and butyl benzyl phthalate (BBP) were recently...

Automated batch emulsion copolymerization of styrene and butyl acrylate

NARCIS (Netherlands)

Mballa Mballa, M.A.; Schubert, U.S.; Heuts, J.P.A.; Herk, van A.M.

2011-01-01

This article describes a method for carrying out emulsion copolymerization using an automated synthesizer. For this purpose, batch emulsion copolymerizations of styrene and butyl acrylate were investigated. The optimization of the polymerization system required tuning the liquid transfer method,

Molecular recognition study of ethosuximide by the supramolecular probe, p-t-butyl calix(8)arene

Energy Technology Data Exchange (ETDEWEB)

Meenakshi, C., E-mail: geethu.laxi@gmail.com [Department of Chemistry, Shri Meenakshi Government College for Women (Autonomous), Madurai 625002 (India); Sangeetha, P.; Ramakrishnan, V. [Department of Laser Studies, School of Physics, Madurai Kamaraj University, Madurai 625021 (India)

2013-06-15

The supramolecule, p-t-Butyl calix(8)arene, forms inclusion complex with the antiseizure drug molecule, ethosuximide. This feature is explained on the basis of optical absorption spectroscopy. Here p-t-Butyl calix(8)arene is the host molecule and ethosuximide is the guest molecule. The stoichiometry of the host–guest complex and the binding constant has been determined using Benesi–Hildebrand plot. Based on the result obtained the structure of the inclusion complex has been proposed. -- Highlights: ► Third generation supramolecule, t-butyl calix (8) arene, is used as a host molecule. ► Anti seizure drug molecule is used as a guest molecule. ► Inclusion complex is formed between the host and guest molecule.

Effect of Electron Beam Irradiation on the Structural Properties of Poly (Vinyl Alcohol) Formulations with Triphenyl Tetrazolium Chloride Dye (TTC)

International Nuclear Information System (INIS)

Ali, Z.I.; Said, H.M.; Ali, H.E.

2005-01-01

Films of poly (vinyl alcohol) (PVA) composites with triphenyl tetrazolium chloride (TTC) dye were prepared and exposed to various radiation doses delivered by accelerated electrons. The results showed that at a low dose of 50 kGy, the color difference (Δ E) of PVA/TTC films was increased by -10 times of the initial value. However, the change in colour differences did not go systematically with increasing the TTC content, in which the composite with 1.5 wt% displayed higher value than that with 3.5 wt%. The differential scanning calorimetry (DSC) showed that the presence of the TTC dye caused a depression in the melting point (Tm) and heat of fusion (Δ Hf) of the PVA bulk polymer. However, the thermogravimetric analysis (TGA) showed that the presence of the TTC dye improved the thermal stability of PVA. Also, the tensile strength at break of PVA/TTC composites was improved after electron beam irradiation. Keywords: PVA, PVA/TTC composites, Electron beam irradiation, color strength, FTIR, thermal and mechanical characterization

In situ 1H NMR studies of high-temperature nitroxide-mediated polymerization of n-butyl acrylate

NARCIS (Netherlands)

Hlalele, L.; Klumperman, L.

2011-01-01

This paper presents results on the independence of the rate of polymerization of n-butyl acrylate (n-BA) toward initial concentration of the alkoxyamine initiator. The alkoxyamine, 2-methyl-2-[N-tert-butyl-N-(1-diethoxyphosphoryl-2,2-dimethylpropyl)aminooxy]propionic acid (MAMA-DEPN), was used to

Atomic Force Microscopy Based Thermal Lithography of Poly(tert-butyl acrylate) Block Copolymer Films for Bioconjugation

NARCIS (Netherlands)

Duvigneau, Joost; Schönherr, Holger; Vancso, Gyula J.

2008-01-01

In this paper, we report on the local thermal activation of thin polymer films for area-selective surface chemical modification on micrometer and nanometer length scales. The thermally induced activation of tert-butyl ester moieties in polystyrene-block-poly(tert-butyl acrylate) (PS-b-PtBA) block

Synthesis and Exfoliation of Discotic Zirconium Phosphates to Obtain Colloidal Liquid Crystals

Science.gov (United States)

Yu, Yi-Hsien; Wang, Xuezhen; Shinde, Abhijeet; Cheng, Zhengdong

2016-01-01

Due to their abundance in natural clay and potential applications in advanced materials, discotic nanoparticles are of interest to scientists and engineers. Growth of such anisotropic nanocrystals through a simple chemical method is a challenging task. In this study, we fabricate discotic nanodisks of zirconium phosphate [Zr(HPO4)2·H2O] as a model material using hydrothermal, reflux and microwave-assisted methods. Growth of crystals is controlled by duration time, temperature, and concentration of reacting species. The novelty of the adopted methods is that discotic crystals of size ranging from hundred nanometers to few micrometers can be obtained while keeping the polydispersity well within control. The layered discotic crystals are converted to monolayers by exfoliation with tetra-(n)-butyl ammonium hydroxide [(C4H9)4NOH, TBAOH]. Exfoliated disks show isotropic and nematic liquid crystal phases. Size and polydispersity of disk suspensions is highly important in deciding their phase behavior. PMID:27284765

Temperature effect on tert-butyl alcohol (TBA) biodegradation kinetics in hyporheic zone soils.

Science.gov (United States)

Greenwood, Mark H; Sims, Ronald C; McLean, Joan E; Doucette, William J

2007-09-19

Remediation of tert-butyl alcohol (TBA) in subsurface waters should be taken into consideration at reformulated gasoline contaminated sites since it is a biodegradation intermediate of methyl tert-butyl ether (MTBE), ethyl tert-butyl ether (ETBE), and tert-butyl formate (TBF). The effect of temperature on TBA biodegradation has not been not been published in the literature. Biodegradation of [U 14C] TBA was determined using hyporheic zone soil microcosms. First order mineralization rate constants of TBA at 5 degrees C, 15 degrees C and 25 degrees C were 7.84 +/- 0.14 x 10-3, 9.07 +/- 0.09 x 10-3, and 15.3 +/- 0.3 x 10-3 days-1, respectively (or 2.86 +/- 0.05, 3.31 +/- 0.03, 5.60 +/- 0.14 years-1, respectively). Temperature had a statistically significant effect on the mineralization rates and was modelled using the Arrhenius equation with frequency factor (A) and activation energy (Ea) of 154 day-1 and 23,006 mol/J, respectively. Results of this study are the first to determine mineralization rates of TBA for different temperatures. The kinetic rates determined in this study can be used in groundwater fate and transport modelling of TBA at the Ronan, MT site and provide an estimate for TBA removal at other similar shallow aquifer sites and hyporheic zones as a function of seasonal change in temperature.

Higher levels of ethyl paraben and butyl paraben in rat amniotic fluid than in maternal plasma after subcutaneous administration

DEFF Research Database (Denmark)

Frederiksen, Hanne; Taxvig, Camilla; Hass, Ulla

2008-01-01

to obtain more knowledge about the distribution of ethyl paraben and butyl paraben in pregnant rats and pups after perinatal exposure, the presented study was designed. The data show response and distribution of ethyl paraben and butyl paraben in maternal rat plasma, pools of amniotic fluids, placenta......, whole-body fetuses, and in fetal liver after dosing of dams with 100, 200, and 400 mg/kg body weight (bw)/day from gestational day 7 to 21. After cesarean section of dams, the fluids and tissues were collected, deconjugated, and purified by solid-phase extraction, and ethyl paraben and butyl paraben...... were analyzed by liquid chromatography-tandem mass spectrometry. Markedly higher levels of ethyl paraben compared to butyl paraben were found in all fluids and tissues. Both ethyl paraben and butyl paraben in maternal plasma, livers, and whole-body tissues from fetus seemed to be saturated after dosing...

Estimation of the fraction of biologically active methyl tert-butyl ether degraders in a heterogeneous biomass sample

DEFF Research Database (Denmark)

Waul, Christopher Kevin; Arvin, Erik; Schmidt, Jens Ejbye

2008-01-01

The fraction of biologically active methyl tert-butyl ether degraders in reactors is just as important for prediction of removal rates as knowledge of the kinetic parameters. The fraction of biologically active methyl tert-butyl ether degraders in a heterogeneous biomass sample, taken from a packed...... bed reactor, was determined using a batch kinetic based approach. The procedure involved modeling of methyl tert-butyl ether removal rates from batch experiments followed by parameter estimations. It was estimated to be 5-14% (w/w) of the measured volatile suspended solids concentration in the reactor....

76 FR 5696 - Fluazifop-P-butyl; Pesticide Tolerances

Science.gov (United States)

2011-02-02

...: This regulation establishes tolerances for residues of fluazifop-P-butyl in or on multiple commodities... based on maternal body weight gain decrement during GD 7- 16. Incidental oral intermediate- NOAEL= 0.74....0 and 2% at 200 mg dose.) mg/kg/day based on fetal UFA = 10x weight decrement, UFH = 10x hydroureter...

Endoscopic application of n-butyl-2-cyanoacrylate on esophagojejunal anastomotic leak: a case report

Directory of Open Access Journals (Sweden)

Angelopoulos Stamatis

2011-03-01

Full Text Available Abstract Introduction This case report describes an esophagojejunal anastomotic leak following total gastrectomy for gastric cancer. The leak was treated successfully with endoscopic application of n-butyl-2-cyanoacrylate. This is the first case report on the endoscopic application of cyanoacrylate alone for the treatment of an anastomotic leak. Case presentation This report describes a case of a 68-year-old Caucasian man who underwent surgery for gastric cancer. He underwent total gastrectomy and esophagojejunal anastomosis with Roux-en-Y anastomosis plus transverse colectomy. An anastomotic leak was treated conservatively at first for a total of three weeks. However, the leak persisted; therefore, the decision was made to apply topical endoscopic n-butyl-2-cyanoacrylate. Conclusion The endoscopic application of n-butyl-2-cyanoacrylate alone can be used successfully to treat esophagojejunal anastomotic leakage.

A green-emitting CdSe/Poly(butyl acrylate) nanocomposite

NARCIS (Netherlands)

Peres, M.; Costa, L.C.; Neves, A.; Soares, M.J.; Monteiro, T.; Carvalho Esteves, de A.C.; Barros-Timmons, A.M.M.V.; Trindade, T.; Kholkin, A.; Alves, E.

2005-01-01

CdSe/poly(butyl acrylate) nanocomposites were synthesized by in situ miniemulsion polymerization. The hybrid nanomaterial is very stable and presents a bright green photoluminescence at 2.29 eV under ultraviolet excitation. With the excitation conditions used the intensity of the emission band keeps

On the viscosity of two 1-butyl-1-methylpyrrolidinium ionic liquids: effect of the temperature and pressure

DEFF Research Database (Denmark)

Gaciño, Félix M.; Comuñas, María J.P.; Regueira Muñiz, Teresa

2015-01-01

to measure viscosities as a function of temperature and pressure fortwo ionic liquids (ILs): 1-butyl-1-methylpyrrolidinium tris(pentafluoroethyl)trifluorophosphateand 1-butyl-1-methylpyrrolidinium trifluoromethanesulfonate.Besides, we have measured the flow curves at pressures up to 75 MPa and shear rates up...

Temperature influence on mixing properties of {ethyl tert-butyl ether (ETBE) + gasoline additives}

International Nuclear Information System (INIS)

Gonzalez-Olmos, R.; Iglesias, M.

2007-01-01

The densities and ultrasonic velocity of {ethyl tert-butyl ether (ETBE) + (benzene, toluene, ethylbenzene, isooctane, tert-butyl alcohol, and ethanol)} over the temperature range (288.15 to 323.15) K and atmospheric pressure, have been measured over the whole concentration range. The experimental excess volumes and deviation of isentropic compressibilities data have been analysed in terms of different theoretical models. The gathered data improve open literature related to gasoline additives, and help to understand the ETBE volumetric and acoustic trend into different chemical environment

Temperature effect on tert-butyl alcohol (TBA biodegradation kinetics in hyporheic zone soils

Directory of Open Access Journals (Sweden)

Sims Ronald C

2007-09-01

Full Text Available Abstract Background Remediation of tert-butyl alcohol (TBA in subsurface waters should be taken into consideration at reformulated gasoline contaminated sites since it is a biodegradation intermediate of methyl tert-butyl ether (MTBE, ethyl tert-butyl ether (ETBE, and tert-butyl formate (TBF. The effect of temperature on TBA biodegradation has not been not been published in the literature. Methods Biodegradation of [U 14C] TBA was determined using hyporheic zone soil microcosms. Results First order mineralization rate constants of TBA at 5°C, 15°C and 25°C were 7.84 ± 0.14 × 10-3, 9.07 ± 0.09 × 10-3, and 15.3 ± 0.3 × 10-3 days-1, respectively (or 2.86 ± 0.05, 3.31 ± 0.03, 5.60 ± 0.14 years-1, respectively. Temperature had a statistically significant effect on the mineralization rates and was modelled using the Arrhenius equation with frequency factor (A and activation energy (Ea of 154 day-1 and 23,006 mol/J, respectively. Conclusion Results of this study are the first to determine mineralization rates of TBA for different temperatures. The kinetic rates determined in this study can be used in groundwater fate and transport modelling of TBA at the Ronan, MT site and provide an estimate for TBA removal at other similar shallow aquifer sites and hyporheic zones as a function of seasonal change in temperature.

Synthesis and characterization of tris[butyl-(1-methyl-3-phenyl-propyl)-dithiocarbamato]-cobalt(III) seskvitoluene

OpenAIRE

TIBOR SABO; ISMET M. HODZIC; SRECKO R. TRIFUNOVIC; VESNA M. DJINOVIC; GORAN N. KALUDJEROVIC

2002-01-01

A new bidentate ligand butyl-(1-methyl-3-phenyl-propyl)-dithiocarbamate (bmFpdtc) was prepared, as the sodium salt. In the reaction of hexaaminecobalt(III) chloride with NabmFpdtc, the corresponding tris[butyl-(1-methyl-3-phenyl-propyl)-dithiocarbamato]cobalt(III), [Co(bmFpdtc)3] complex was prepared. The complex was characterized by elemental analysis, infrared, electronic absorption, 1H and 13C-NMR spectroscopy.

Environmentally relevant organophosphate triesters in herring gulls: In vitro biotransformation and kinetics and diester metabolite formation using a hepatic microsomal assay

International Nuclear Information System (INIS)

Greaves, Alana K.; Su, Guanyong; Letcher, Robert J.

2016-01-01

The in vitro biotransformation and kinetics of six organophosphate triester (OPE) flame retardants were investigated in herring gulls (Larus argentatus) from the Great Lakes using a hepatic microsomal metabolism assay. Administration of each individual OPE (tri-n-butyl phosphate (TNBP), tris(2-butoxyethyl) phosphate (TBOEP), triphenyl phosphate (TPHP), triethyl phosphate (TEP), tris(1,3-dichloro-2-propyl) phosphate (TDCIPP) and tris(2-chloroisopropyl) phosphate (TCIPP)) to the in vitro assay (concentration range 0.01 to 10 μM) resulted in rapid depletion with the exception of TEP. Following the Michaelis-Menten enzyme kinetics model, a preliminary 2-minute incubation period was used to estimate the V max (± SE) values (i.e., the maximal rate of reaction for a saturated enzyme system), which ranged from 5.0 ± 0.4 (TPHP) to 29 ± 18 pmol/min/mg protein (TBOEP), as well as the K M (± SE) values (i.e., the OPE concentration corresponding to one half of the V max ), which ranged from 9.8 ± 1 (TPHP) to 189 ± 135 nM (TBOEP). Biotransformation assays over a 100-minute incubation period revealed that TNBP was metabolized most rapidly (with a depletion rate of 73 ± 4 pmol/min/mg protein), followed by TBOEP (53 ± 8 pmol/min/mg), TCIPP (27 ± 1 pmol/min/mg), TPHP (22 ± 2 pmol/min/mg) and TDCIPP (8 ± 1 pmol/min/mg). In vitro biotransformation of OP triesters was clearly structure-dependent where non-halogenated alkyl OP triesters were metabolized more rapidly than halogenated alkyl triesters. Halogenated OP triesters were transformed to their respective diesters more efficiently relative to non-halogenated OP triesters. To our knowledge, this is the first study to investigate OP triester metabolism and OP diester formation in an avian or wildlife model system, which is important to understand the fate and biological activity of OPEs in an exposed organism. - Highlights: • The metabolism and kinetics of 6 OPEs were examined in herring gull liver microsomes. • The

Environmentally relevant organophosphate triesters in herring gulls: In vitro biotransformation and kinetics and diester metabolite formation using a hepatic microsomal assay

Energy Technology Data Exchange (ETDEWEB)

Greaves, Alana K. [Wildlife and Landscape Directorate, Science and Technology Branch, Environment and Climate Change Canada, National Wildlife Research Centre, Carleton University, Ottawa, ON K1A 0H3 (Canada); Department of Chemistry, Carleton University, Ottawa, ON K1S 5B6 (Canada); Su, Guanyong, E-mail: guanyong.su85@gmail.com [Wildlife and Landscape Directorate, Science and Technology Branch, Environment and Climate Change Canada, National Wildlife Research Centre, Carleton University, Ottawa, ON K1A 0H3 (Canada); Department of Chemistry, Carleton University, Ottawa, ON K1S 5B6 (Canada); Letcher, Robert J., E-mail: robert.letcher@canada.ca [Wildlife and Landscape Directorate, Science and Technology Branch, Environment and Climate Change Canada, National Wildlife Research Centre, Carleton University, Ottawa, ON K1A 0H3 (Canada); Department of Chemistry, Carleton University, Ottawa, ON K1S 5B6 (Canada)

2016-10-01

The in vitro biotransformation and kinetics of six organophosphate triester (OPE) flame retardants were investigated in herring gulls (Larus argentatus) from the Great Lakes using a hepatic microsomal metabolism assay. Administration of each individual OPE (tri-n-butyl phosphate (TNBP), tris(2-butoxyethyl) phosphate (TBOEP), triphenyl phosphate (TPHP), triethyl phosphate (TEP), tris(1,3-dichloro-2-propyl) phosphate (TDCIPP) and tris(2-chloroisopropyl) phosphate (TCIPP)) to the in vitro assay (concentration range 0.01 to 10 μM) resulted in rapid depletion with the exception of TEP. Following the Michaelis-Menten enzyme kinetics model, a preliminary 2-minute incubation period was used to estimate the V{sub max} (± SE) values (i.e., the maximal rate of reaction for a saturated enzyme system), which ranged from 5.0 ± 0.4 (TPHP) to 29 ± 18 pmol/min/mg protein (TBOEP), as well as the K{sub M} (± SE) values (i.e., the OPE concentration corresponding to one half of the V{sub max}), which ranged from 9.8 ± 1 (TPHP) to 189 ± 135 nM (TBOEP). Biotransformation assays over a 100-minute incubation period revealed that TNBP was metabolized most rapidly (with a depletion rate of 73 ± 4 pmol/min/mg protein), followed by TBOEP (53 ± 8 pmol/min/mg), TCIPP (27 ± 1 pmol/min/mg), TPHP (22 ± 2 pmol/min/mg) and TDCIPP (8 ± 1 pmol/min/mg). In vitro biotransformation of OP triesters was clearly structure-dependent where non-halogenated alkyl OP triesters were metabolized more rapidly than halogenated alkyl triesters. Halogenated OP triesters were transformed to their respective diesters more efficiently relative to non-halogenated OP triesters. To our knowledge, this is the first study to investigate OP triester metabolism and OP diester formation in an avian or wildlife model system, which is important to understand the fate and biological activity of OPEs in an exposed organism. - Highlights: • The metabolism and kinetics of 6 OPEs were examined in herring gull liver

Sorption of methyl tert-butyl ether (MTBE) and tert-butyl alcohol (TBA) to synthetic resins.

Science.gov (United States)

Bi, Erping; Haderlein, Stefan B; Schmidt, Torsten C

2005-10-01

Methyl tert-butyl ether (MTBE) is a widely used gasoline oxygenate. Contamination of MTBE and its major degradation product tert-butyl alcohol (TBA) in groundwater and surface water has received great attention. However, sorption affinity and sorption mechanisms of MTBE and TBA to synthetic resins, which can be potentially used in removal of these contaminants from water, in passive sampling, or in enrichment of bacteria, have not been studied systemically. In this study, kinetic and equilibrium sorption experiments (single solute and binary mixtures) on four synthetic resins were conducted. The sorption affinity of the investigated sorbents for MTBE and TBA decreases in the order Ambersorb 563>Optipore L493>Amberlite XAD4>Amberlite XAD7, and all show higher sorption affinity for MTBE than for TBA. Binary experiments with o-xylene, a major compound of gasoline as co-contaminant, imply that all resins preferentially sorb o-xylene over MTBE or TBA, i.e., there is sorption competition. In the equilibrium aqueous concentration (Ceq) range (0.1-139.0 mg/L for MTBE, and 0.01-48.4 mg/L for TBA), experimental and modeling results as well as sorbent characteristics indicate that micropore filling and/or some other type of adsorption process (e.g., adsorption to specific sites of high sorption potential at low concentrations) rather than partitioning were the dominant sorption mechanisms. Optipore L493 has favourable sorption and desorption characteristics, and is a suitable sorbent, e.g., in bacteria enrichment or passive sampling for moderately polar compounds. However, for highly polar compounds such as TBA, Ambersorb 563 might be a better choice, especially in water treatment.

Simulation of the plant uptake of organophosphates and other emerging pollutants for greenhouse experiments and field conditions

DEFF Research Database (Denmark)

Trapp, Stefan; Eggen, Trine

2013-01-01

The uptake of the organophosphates tris(2-chloroethyl) phosphate (TCEP), tris(1-chloro-2-propyl) phosphate (TCPP), tributyl phosphate (TBP), the insect repellant N,N-diethyl toluamide (DEET), and the plasticizer n-butyl benzenesulfonamide (NBBS) into plants was studied in greenhouse experiments...

Degradation of a recalcitrant xenobiotic compound: methyl tert-butyl ether (MTBE) metabolism by mycobacterium austroafricanum; Degradation d'un compose xenobiotique recalcitrant: metabolisme du methyl tert-butyl ether (MTBE) par mycobacterium austroafricanum IFP 2012

Energy Technology Data Exchange (ETDEWEB)

Francois, A

2002-11-01

Methyl tert-butyl ether (MTBE) is introduced up to 15% (vol/vol) in gasoline in order to obtain a good octane number and to prevent carbon monoxide emissions. However, as a consequence of storage tanks leakage, MTBE became one of the major pollutants of aquifers because of its very low biodegradability. The present study aimed at investigating the biodegradation of MTBE by Mycobacterium austroafricanum IFP 2012. The MTBE metabolic pathway was partially elucidated owing to the identification of some intermediates (tert-butyl formate (TBF), tert-butyl alcohol (TBA), a-hydroxy-isobutyric acid and acetone) and some enzymatic activities (MTBE/TBA monooxygenase (non hemic and inducible), TBF esterase, 2-propanol: NDMA oxidoreductase and another monooxygenase involved in acetone degradation). The involvement of TBF and the requirement of cobalt could be explanations for the low natural attenuation of MTBE; whereas the methoxy group does not seem to be implicated. (author)

Levels of synthetic antioxidants (ethoxyquin, butylated hydroxytoluene and butylated hydroxyanisole) in fish feed and commercially farmed fish.

Science.gov (United States)

Lundebye, A-K; Hove, H; Måge, A; Bohne, V J B; Hamre, K

2010-12-01

Several synthetic antioxidants are authorized for use as feed additives in the European Union. Ethoxyquin (EQ) and butylated hydroxytoluene (BHT) are generally added to fish meal and fish oil, respectively, to limit lipid oxidation. The study was conducted to examine the concentrations of EQ, BHT and butylated hydroxyanisole (BHA) in several commercially important species of farmed fish, namely Atlantic salmon, halibut and cod and rainbow trout, as well as concentrations in fish feed. The highest levels of BHT, EQ and BHA were found in farmed Atlantic salmon fillets, and were 7.60, 0.17 and 0.07 mg kg(-1), respectively. The lowest concentrations of the synthetic antioxidants found were in cod. The concentration of the oxidation product ethoxyquin dimer (EQDM) was more than ten-fold higher than the concentration of parent EQ in Atlantic salmon halibut and rainbow trout, whereas this dimer was not detected in cod fillets. The theoretical consumer exposure to the synthetic antioxidants EQ, BHA and BHT from the consumption of farmed fish was calculated. The contribution of EQ from a single portion (300 g) of skinned fillets of the different species of farmed fish would contribute at most 15% of the acceptable daily intake (ADI) for a 60 kg adult. The consumption of farmed fish would not contribute measurably to the intake of BHA; however, a 300 g portion of farmed Atlantic salmon would contribute up to 75% of the ADI for BHT.

Synthesis and characterization of tris[butyl-(1-methyl-3-phenyl-propyl-dithiocarbamato]-cobalt(III seskvitoluene

Directory of Open Access Journals (Sweden)

TIBOR SABO

2002-02-01

Full Text Available A new bidentate ligand butyl-(1-methyl-3-phenyl-propyl-dithiocarbamate (bmFpdtc was prepared, as the sodium salt. In the reaction of hexaaminecobalt(III chloride with NabmFpdtc, the corresponding tris[butyl-(1-methyl-3-phenyl-propyl-dithiocarbamato]cobalt(III, [Co(bmFpdtc3] complex was prepared. The complex was characterized by elemental analysis, infrared, electronic absorption, 1H and 13C-NMR spectroscopy.

Polyvinylpolypyrrolidone-Supported Boron Trifluoride; Highly Efficient Catalyst for the Synthesis of N-tert-Butyl Amides

Directory of Open Access Journals (Sweden)

Masoud Mokhtary

2012-01-01

Full Text Available Highly efficient method for the preparation of N-tert-butyl amides by reaction of nitriles with tert-butyl acetate is described using polyvinylpolypyrrolidone-supported boron trifluoride (PVPP-BF3 at 70°C in good to excellent yields. Selective amidation of benzonitrile in the presence of acetonitrile was also achieved. polyvinylpolypyrrolidone-boron trifluoride complex shows non-corrosive and stable solid catalyst elevated Lewis acid property.

Tri(t-butyl)phosphine-assisted selective hydrosilylation of terminal alkynes

Institute of Scientific and Technical Information of China (English)

无

2010-01-01

A highly efficient and regio-/stereoselective method of hydrosilylating terminal alkynes was developed using Pt(DVDS)-tri(t-butyl) phosphine catalyst system at room temperature.Trans-products or alpha-products were obtained almost exclusively depending on the alkynes and silanes employed.

Atom transfer radical copolymerization of styrene and butyl acrylate

NARCIS (Netherlands)

Chambard, G.; Klumperman, B.; Matyjaszewski, K.

2000-01-01

Atom transfer radical polymerization of styrene and butyl acrylate has been investigated from a kinetic point of view. Attention is focused on the activation of the dormant species as well as on the termination that plays a role in these reactions. It has been shown that the activation of a styrene

Phosphorus release from phosphate rock and iron phosphate by low-molecular-weight organic acids.

Science.gov (United States)

Xu, Ren-kou; Zhu, Yong-guan; Chittleborough, David

2004-01-01

Low-molecular-weight(LMW) organic acids widely exist in soils, particularly in the rhizosphere. A series of batch experiments were carried out to investigate the phosphorus release from rock phosphate and iron phosphate by low-molecular-weight organic acids. Results showed that citric acid had the highest capacity to solubilize P from both rock and iron phosphate. P solubilization from rock phosphate and iron phosphate resulted in net proton consumption. P release from rock phosphate was positively correlated with the pKa values. P release from iron phosphate was positively correlated with Fe-organic acid stability constants except for aromatic acids, but was notcorrelated with pKa. Increase in the concentrations of organic acids enhanced P solubilization from both rock and iron phosphate almost linearly. Addition of phenolic compounds further increased the P release from iron phosphate. Initial solution pH had much more substantial effect on P release from rock phosphate than from iron phosphate.

Thermodynamic properties of 1-butyl-3-methylpyridinium tetrafluoroborate

International Nuclear Information System (INIS)

Safarov, Javid; Kul, Ismail; El-Awady, Waleed A.; Shahverdiyev, Astan; Hassel, Egon

2011-01-01

Highlights: → (p, ρ, T) data of 1-butyl-3-methylpyridinium tetrafluoroborate are estimated. → The measurements were carried out with a vibration-tube densimeter. → The thermomechanical coefficients were calculated. - Abstract: Pressure, density, temperature (p, ρ, T) data of 1-butyl-3-methylpyridinium tetrafluoroborate [C4mpyr][BF 4 ] at T = (283.15 to 393.15) K and pressures up to p = 100 MPa are reported with an estimated experimental relative combined standard uncertainty of Δρ/ρ = ±(0.01 to 0.08)% in density. The measurements were carried out with a newly constructed Anton-Paar DMA HPM vibration-tube densimeter. The system was calibrated using double-distilled water, methanol, toluene and aqueous NaCl solutions. An empirical equation of state for fitting of the (p, ρ, T) data of [C4mpyr][BF 4 ] has been developed as a function of pressure and temperature to calculate the thermal properties of the ionic liquid (IL), such as isothermal compressibility, isobaric thermal expansibility, differences in isobaric and isochoric heat capacities, thermal pressure coefficient and internal pressure. Internal pressure and the temperature coefficient of internal pressure data were used to make conclusions on the molecular characteristics of the IL.

Influence Of Initiator Types And Emulsion Polymerization Techniques To Particle Size Of Copolymerization Styrene-Butyl Acrylate-Methyl Methacrylate

Directory of Open Access Journals (Sweden)

Ariyanti Sarwono

2008-11-01

Full Text Available Influence of initiator types and emulsion polymerization techniques to particle size of copolymerization styrene-butyl acrylate-methyl methacrylate. Copoly(styrene/butyl acrylic/methyl methacrylic was prepared by emulsion polymerization method. This paper describes effect of insiator types i.e. ammonium persulfate (APS, hydrogen peroxide, ters-butyl peroxide (TBHP, initiator redox (H2O2/ascorbic acid and polymerization techniques i.e. batch and semicontinue to particle size distribution of copoly(styrene/butyl acrylic/methyl methacrylic. Initiator TBHP and H2O2 could not initiate copolymerization properly, but initiator APS and redox initiate copolymerization with batch and semi continue techniques could well perform. The higher concentration of APS, the greater particle size of the copolymer, but the copolymer is polymodal. Initiator redox (H2O2/ascorbic acid produced greater particle size than initiator redox (ascorbic acid/ H2O2.

Enhanced Heterogeneous Catalytic Conversion of Furfuryl Alcohol into Butyl Levulinate

NARCIS (Netherlands)

Carà, P.D..; Ciriminna, R.; Shiju, N.R.; Rothenberg, G.; Pagliaro, M.

2014-01-01

We study the catalytic condensation of furfuryl alcohol with 1-butanol to butyl levulinate. A screening of several commercial and as-synthesized solid acid catalysts shows that propylsulfonic acid-functionalized mesoporous silica outperforms the state-of-the-art phosphotungstate acid catalysts. The

Pressure-induced phase transition of 1-butyl-3-methylimidazolium hexafluorophosphate [bmim][PF6

Science.gov (United States)

Takekiyo, Takahiro; Hatano, Naohiro; Imai, Yusuke; Abe, Hiroshi; Yoshimura, Yukihiro

2011-03-01

We have investigated the pressure-induced Raman spectral change of 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF6]) using Raman spectroscopy. The relative Raman intensity at 590 cm-1 of the CH2 rocking band assigned to the gauche conformer of the NCCC dihedral angle of the butyl group in the [bmim]+ cation increases when the pressure-induced liquid-crystalline phase transition occurs, while that at 610 cm-1 assigned to the trans conformer decreases. Our results show that the high-pressure phase transition of [bmim][PF6] causes the increase of the gauche conformer of the [bmim]+ cation.

Degradation of a recalcitrant xenobiotic compound: methyl tert-butyl ether (MTBE) metabolism by mycobacterium austroafricanum; Degradation d'un compose xenobiotique recalcitrant: metabolisme du methyl tert-butyl ether (MTBE) par mycobacterium austroafricanum IFP 2012

Energy Technology Data Exchange (ETDEWEB)

Francois, A.

2002-11-01

Methyl tert-butyl ether (MTBE) is introduced up to 15% (vol/vol) in gasoline in order to obtain a good octane number and to prevent carbon monoxide emissions. However, as a consequence of storage tanks leakage, MTBE became one of the major pollutants of aquifers because of its very low biodegradability. The present study aimed at investigating the biodegradation of MTBE by Mycobacterium austroafricanum IFP 2012. The MTBE metabolic pathway was partially elucidated owing to the identification of some intermediates (tert-butyl formate (TBF), tert-butyl alcohol (TBA), a-hydroxy-isobutyric acid and acetone) and some enzymatic activities (MTBE/TBA monooxygenase (non hemic and inducible), TBF esterase, 2-propanol: NDMA oxidoreductase and another monooxygenase involved in acetone degradation). The involvement of TBF and the requirement of cobalt could be explanations for the low natural attenuation of MTBE; whereas the methoxy group does not seem to be implicated. (author)

Preparation of poly(acrylonitrile-butyl acrylate) gel electrolyte for lithium-ion batteries

International Nuclear Information System (INIS)

Tian Zheng; He Xiangming; Pu Weihua; Wan Chunrong; Jiang Changyin

2006-01-01

Poly(acrylonitrile-butyl acrylate) gel polymer electrolyte was prepared for lithium ion batteries. The preparation started with synthesis of poly(acrylonitrile-butyl acrylate) by radical emulsion polymerization, followed by phase inversion to produce microporous membrane. Then, the microporous gel polymer electrolytes (MGPEs) was prepared with the microporous membrane and LiPF 6 in ethylene carbonate/diethyl carbonate. The dry microporous membrane showed a fracture strength as high as 18.98 MPa. As-prepared gel polymer electrolytes presented ionic conductivity in excess of 3.0 x 10 -3 S cm -1 at ambient temperature and a decomposition voltage over 6.6 V. The results showed that the as-prepared gel polymer electrolytes were promising materials for Li-ion batteries

Effect of Mesoporous Diatomite Particles on the Kinetics of SR&NI ATRP of Styrene and Butyl Acrylate

Science.gov (United States)

Khezri, Khezrollah; Ghasemi, Moosa; Fazli, Yousef

2018-05-01

Mesoporous diatomite particles were employed to prepare different poly(styrene-co-butyl acrylate)/diatomite nanocomposites. Diatomite nanoplatelets were used for in situ copolymerization of styrene and butyl acrylate by SR&NI ATRP to synthesize well-defined poly(styrene-co-butyl acrylate) nanocomposites. Nitrogen adsorption/desorption isotherm is applied to examine surface area and structural characteristics of the diatomite nanoplatelets. Evaluation of pore size distribution and morphological studies were also performed by SEM and TEM. Conversion and molecular weight determinations were carried out using gas and size exclusion chromatography respectively. Addition of 3 wt% pristine mesoporous diatomite nanoplatelets leads to increase of conversion from 73 to 89%. Molecular weight of poly(styrene-co-butyl acrylate) chains increases from 17,115 to 20,343 g·mol-1 by addition of 3 wt% pristine mesoporous diatomite; however, polydispersity index values increases from 1.14 to 1.37. Increasing thermal stability of the nanocomposites is demonstrated by TGA. Differential scanning calorimetry shows an increase in glass transition temperature from 35.26 to 39.61°C by adding 3 wt% of mesoporous diatomite nanoplatelets.

Continuous synthesis of tert.-butyl peroxypivalate using a single channel micro reactor equipped with orifices as emulsification units

NARCIS (Netherlands)

Illg, T.; Hessel, V.; Löb, P.; Schouten, J.C.

2011-01-01

The two-step synthesis of tert-butyl peroxypivalate is performed in a single-channel microreactor. The first step, the deprotonation of tert-butyl hydroperoxide, is done in a simple mixer tube setup. The residence time section for the second reaction step is equipped with orifices for interfacial

Removal of phosphate from solution by adsorption and precipitation of calcium phosphate onto monohydrocalcite.

Science.gov (United States)

Yagi, Shintaro; Fukushi, Keisuke

2012-10-15

The sorption behavior and mechanism of phosphate on monohydrocalcite (CaCO(3)·H(2)O: MHC) were examined using batch sorption experiments as a function of phosphate concentrations, ionic strengths, temperatures, and reaction times. The mode of PO(4) sorption is divisible into three processes depending on the phosphate loading. At low phosphate concentrations, phosphate is removed by coprecipitation of phosphate during the transformation of MHC to calcite. The sorption mode at the low-to-moderate phosphate concentrations is most likely an adsorption process because the sorption isotherm at the conditions can be fitted reasonably with the Langmuir equation. The rapid sorption kinetics at the conditions is also consistent with the adsorption reaction. The adsorption of phosphate on MHC depends strongly on ionic strength, but slightly on temperature. The maximum adsorption capacities of MHC obtained from the regression of the experimental data to the Langmuir equation are higher than those reported for stable calcium carbonate (calcite or aragonite) in any conditions. At high phosphate concentrations, the amount of sorption deviates from the Langmuir isotherm, which can fit the low-to-moderate phosphate concentrations. Speciation-saturation analyses of the reacted solutions at the conditions indicated that the solution compositions which deviate from the Langmuir equation are supersaturated with respect to a certain calcium phosphate. The obtained calcium phosphate is most likely amorphous calcium phosphate (Ca(3)(PO(4))(2)·xH(2)O). The formation of the calcium phosphate depends strongly on ionic strength, temperature, and reaction times. The solubility of MHC is higher than calcite and aragonite because of its metastability. Therefore, the higher solubility of MHC facilitates the formation of the calcium phosphates more than with calcite and aragonite. Copyright © 2012 Elsevier Inc. All rights reserved.

Butyl 2-(5-iodo-3-methylsulfinyl-1-benzofuran-2-ylacetate

Directory of Open Access Journals (Sweden)

Uk Lee

2009-02-01

Full Text Available In the title compound, C15H17IO4S, the O atom and the methyl group of the methylsulfinyl substituent lie on opposite sides of the plane of the benzofuran fragment. The crystal structure is stabilized by weak intermolecular C—H...π interactions between a methyl H atom of the methylsulfinyl group and the benzene ring of the benzofuran system, and by an I...O halogen bond of 3.173 (3 Å and a nearly linear C—I...O angle of 171.7 (1°. In addition, the crystal structure exhibits weak intermolecular C—H...O hydrogen bonds. The O atom of the carbonyl group and the butyl chain are both disordered over two positions with site-occupancy factors from refinement of 0.55 (4 and 0.45 (4 (for the O atom, and 0.76 (2 and 0.24 (2 (for the butyl group.

Crystal structure of 1-butyl-2,3-dimethylimidazolium dicarba-7,8-nido-undecaborate

Directory of Open Access Journals (Sweden)

M. J. Klemes

2015-03-01

Full Text Available In the title molecular salt, C9H17N2+·C2H12B9−, the carborane cage has a bridging B—H—B bond on the open B3C2 face. The butyl side chain of the cation adopts an extended conformation [C—C—C—C = 179.6 (1°]. In the crystal, the imidazolium ring is almost coplanar with the open face of the carborane anion. The cations stack in the [010] direction and the dihedral angle between the imidazolium rings of adjacent cations is 68.45 (6°. The butyl chains extend into the space between carborane anions.

Phosphate Recovery From Sewage Sludge Containing Iron Phosphate

NARCIS (Netherlands)

Wilfert, P.K.

2018-01-01

The scope of this thesis was to lay the basis for a phosphate recovery technology that can be applied on sewage sludge containing iron phosphate. Such a technology should come with minimal changes to the existing sludge treatment configuration while keeping the use of chemicals or energy as small as

Percutaneous N-Butyl cyanoacrylate embolization of a pancreatic pseudoaneurysm after failed attempts of transcatheter embolization

Energy Technology Data Exchange (ETDEWEB)

Kim, Ri Hyeon; Yoo, Roh Eul; Kim, Hyo Cheol [Seoul National University Medical Research Center, and Clinical Research Institute, Seoul National University Hospital, Seoul (Korea, Republic of)

2014-10-15

One common complication after major pancreatic surgery is bleeding. Herein we describe a case of pancreatic pseudoaneurysm which developed after pylorous preserving pancreaticoduodenectomy for common bile duct cancer. Three attempts of transcatheter embolization failed since feeders to the pseudoaneurysm had unfavorable anatomy. Direct percutaneous N-butyl cyanoacrylate injection was performed under fluoroscopy-guidance and the pseudoaneurysm was successfully treated. Percutaneous fluoroscopy-guided direct N-butyl cyanoacrylate injection may be a useful alternative when selective transcatheter embolization fails or is technically challenging.

Preparation of poly(acrylonitrile-butyl acrylate) gel electrolyte for lithium-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Tian Zheng [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); He Xiangming [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China)]. E-mail: hexm@tsinghua.edu.cn; Pu Weihua [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Wan Chunrong [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China); Jiang Changyin [Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing 100084 (China)

2006-10-25

Poly(acrylonitrile-butyl acrylate) gel polymer electrolyte was prepared for lithium ion batteries. The preparation started with synthesis of poly(acrylonitrile-butyl acrylate) by radical emulsion polymerization, followed by phase inversion to produce microporous membrane. Then, the microporous gel polymer electrolytes (MGPEs) was prepared with the microporous membrane and LiPF{sub 6} in ethylene carbonate/diethyl carbonate. The dry microporous membrane showed a fracture strength as high as 18.98 MPa. As-prepared gel polymer electrolytes presented ionic conductivity in excess of 3.0 x 10{sup -3} S cm{sup -1} at ambient temperature and a decomposition voltage over 6.6 V. The results showed that the as-prepared gel polymer electrolytes were promising materials for Li-ion batteries.

Thermophysical properties of 1-butyl-4-methylpyridinium tetrafluoroborate

International Nuclear Information System (INIS)

Safarov, Javid; Kul, Ismail; El-Awady, Waleed A.; Nocke, Jürgen; Shahverdiyev, Astan; Hassel, Egon

2012-01-01

Highlights: ► (p, ρ, T) data of 1-butyl-4-methylpyridinium tetrafluoroborate are estimated. ► The measurements were carried out with a vibration-tube densimeter. ► The thermomechanical coefficients were calculated. - Abstract: Thermophysical properties, {(p, ρ, T) at T = (283.15 to 393.15) K, pressures up to p = 100 MPa, and viscosity at T = (283.15 to 373.15) K and p = 0.101 MPa}, of 1-butyl-4-methylpyridinium tetrafluoroborate [b4mpy][BF 4 ] are reported. The measurements were carried out with a recently constructed Anton-Paar DMA HPM vibration-tube densimeter and a fully automated SVM 3000 Anton-Paar rotational Stabinger viscometer. The vibration-tube densimeter was calibrated using double-distilled water, methanol, toluene, and aqueous NaCl solutions. An empirical equation of state for fitting of the (p, ρ, T) data of [b4mpy][BF 4 ] has been developed as a function of pressure and temperature to calculate the thermal properties of the ionic liquid (IL), such as isothermal compressibility, isobaric thermal expansibility, differences in isobaric and isochoric heat capacities, thermal pressure coefficient, and internal pressure. Internal pressure and the temperature coefficient of internal pressure data were used to make conclusions on the molecular characteristics of the IL.

Solvent and ion-pairing effects on the chlorine kinetic isotope effect of t-butyl chloride

International Nuclear Information System (INIS)

McCord, B.R.

1986-01-01

The solvolysis of t-butyl chloride and 1-adamantyl chloride was measured in mixtures of aqueous 2,2,2-trifluoroethanols and in mixtures of aqueous ethanols. The KIEs for t-butyl chloride at 25 0 C in 94% TFE/water, and 60% ethanol/water (solvent mixtures with similar polarity) were 1.0097 and 1.0104 respectively. Further investigations showed a KIE of 1.0104 in 50% ethanol/water and 1.0105 in 100% ethanol while the isotope effect in the fluorinated ethanols rose from 1.0094 in 99% TFE/water to 1.0101 in 70% ethanol/water. The KIE in all these solvents were shown to be directly proportional to the nucleophilicity of the solvent and indicates nucleophilic attack on an ion pair. The similar KIE of t-butyl chloride in the ethanol/water solvents was found to support the contention that solvent polarity exerts a minimal effect on the chlorine KIE

Phosphate-a poison for humans?

Science.gov (United States)

Komaba, Hirotaka; Fukagawa, Masafumi

2016-10-01

Maintenance of phosphate balance is essential for life, and mammals have developed a sophisticated system to regulate phosphate homeostasis over the course of evolution. However, due to the dependence of phosphate elimination on the kidney, humans with decreased kidney function are likely to be in a positive phosphate balance. Phosphate excess has been well recognized as a critical factor in the pathogenesis of mineral and bone disorders associated with chronic kidney disease, but recent investigations have also uncovered toxic effects of phosphate on the cardiovascular system and the aging process. Compelling evidence also suggests that increased fibroblastic growth factor 23 and parathyroid hormone levels in response to a positive phosphate balance contribute to adverse clinical outcomes. These insights support the current practice of managing serum phosphate in patients with advanced chronic kidney disease, although definitive evidence of these effects is lacking. Given the potential toxicity of excess phosphate, the general population may also be viewed as a target for phosphate management. However, the widespread implementation of dietary phosphate intervention in the general population may not be warranted due to the limited impact of increased phosphate intake on mineral metabolism and clinical outcomes. Nonetheless, the increasing incidence of kidney disease or injury in our aging society emphasizes the potential importance of this issue. Further work is needed to more completely characterize phosphate toxicity and to establish the optimal therapeutic strategy for managing phosphate in patients with chronic kidney disease and in the general population. Copyright © 2016 International Society of Nephrology. Published by Elsevier Inc. All rights reserved.

High-pressure phase behavior of propyl lactate and butyl lactate in supercritical carbon dioxide

International Nuclear Information System (INIS)

Cho, Dong Woo; Shin, Jungin; Shin, Moon Sam; Bae, Won; Kim, Hwayong

2012-01-01

Highlights: ► The phase behavior of propyl lactate and butyl lactate in scCO 2 was measured. ► Experimental data were correlated by the PR-EOS. ► The critical constants were estimated by the three group contribution methods. ► Acentric factor was estimated by the Lee–Kesler method. ► The Nannoolal–Rarey and Lee–Kesler method shows the best correlation results. - Abstract: Lactate esters synthesized with lactic acid and ester are used as solvents and reactants in various industries, including agricultural chemistry, pharmaceuticals, electronics, and fine chemicals. Among lactate esters, high purity propyl lactate and butyl lactate are used to produce fine chemicals and in the synthesis of chiral intermediates for use in pesticides and drugs. However, distillation for the removal of propyl lactate and butyl lactate alters or degenerates products due the high boiling points of these two lactate esters. This problem can be solved by supercritical fluid extraction (SCFE) at lower temperatures. SCFE process requires high-pressure phase behavior data on CO 2 and lactates for its design and operation. In this study, high-pressure phase behavior of propyl lactate and butyl lactate in CO 2 was measured from (323.2 to 363.2) K using a variable-volume view cell apparatus. Experimental data were well correlated by the Peng–Robinson equation of state using the van der Waals one-fluid mixing rules. The critical constants were estimated by the Joback method, the Constantinou–Gani method, and the Nannoolal–Rarey method. Acentric factor was estimated by the Lee–Kesler method.

The beneficial effects of mixing spiro-OMeTAD with n-butyl-substituted copper phthalocyanine for perovskite solar cells

International Nuclear Information System (INIS)

Nouri, Esmaiel; Wang, Yu-Long; Chen, Qian; Xu, Jia-Ju; Dracopoulos, Vassilios; Sygellou, Lamprini; Xu, Zong-Xiang; Mohammadi, Mohammad Reza; Lianos, Panagiotis

2016-01-01

Highlights: • Soluble n-butyl substituted copper phthalocyanine. • Mixture with spiro-OMeTAD and employment in perovskite solar cells. • Impressive improvement of perovskite solar cell efficiency. • n-Butyl derivative gives better results than tert-butyl derivative - Abstract: Perovskite solar cells have been constructed under ambient conditions by using 2,2',7,7'-Tetrakis-(N,N-di-4-methoxyphenylamino)-9,9'-spirobifluorene (spiro-OMeTAD) mixed with a small quantity of soluble tetra-n-butyl substituted copper phthalocyanine as hole transporting material. The introduction of the phthalocyanine derivative resulted in an impressive increase of cell efficiency, which changed from 10.4% in the absence to 15.4% in the presence of phthalocyanine. This effect is related to the creation of deep traps in the hole transporting phase which block back-travelling electrons as well as to the improvement of the structural quality of the spiro-OMeTAD film in the presence of phthalocyanine. Both functionalities decrease shunt paths within the hole transporting phase resulting in increasing the fill factor and the open-circuit voltage of the cell.

Hydrophobic hydration and anomalous excess partial molar volume of tert-butyl alcohol-water mixture studied by quasielastic neutron scattering

International Nuclear Information System (INIS)

Nakada, Masaru; Maruyama, Kenji; Misawa, Masakatsu; Yamamuro, Osamu

2007-01-01

Quasielastic neutron scattering has been used to investigate the hydration of alcohol clusters in tert-butyl alcohol-water mixture. The measurements were made in a range of alcohol concentration, x TBA , from 0.0 to 0.17 in mole fraction at 25degC. Fraction, α, of water molecules hydrated to fractal-surface of alcohol clusters in tert-butyl alcohol-water mixture was obtained as a function of alcohol concentration. Average hydration number N WS of tert-butyl alcohol molecule was derived from the value of α as a function of alcohol concentration. The value of N WS for an isolated alcohol molecule in water was 19-21. The anomalous excess partial molar volume of tert-butyl alcohol-water mixture was interpreted successfully by applying the same model with the same values of volume parameter as used for 1-propanol-water mixture, δ 1 (=-0.36 cm 3 ·mol -1 ) and δ 2 (=0.60 cm 3 ·mol -1 ). (author)

Quercetin protects human hepatoma HepG2 against oxidative stress induced by tert-butyl hydroperoxide

International Nuclear Information System (INIS)

Alia, Mario; Ramos, Sonia; Mateos, Raquel; Granado-Serrano, Ana Belen; Bravo, Laura; Goya, Luis

2006-01-01

Flavonols such as quercetin, have been reported to exhibit a wide range of biological activities related to their antioxidant capacity. The objective of the present study was to investigate the protective effect of quercetin on cell viability and redox status of cultured HepG2 cells submitted to oxidative stress induced by tert-butyl hydroperoxide. Concentrations of reduced glutathione and malondialdehyde, generation of reactive oxygen species and activity and gene expression of antioxidant enzymes were used as markers of cellular oxidative status. Pretreatment of HepG2 with 10 μM quercetin completely prevented lactate dehydrogenase leakage from the cells. Pretreatment for 2 or 20 h with all doses of quercetin (0.1-10 μM) prevented the decrease of reduced glutathione and the increase of malondialdehyde evoked by tert-butyl hydroperoxide in HepG2 cells. Reactive oxygen species generation induced by tert-butyl hydroperoxide was significantly reduced when cells were pretreated for 2 or 20 h with 10 μM and for 20 h with 5 μM quercetin. Finally, some of the quercetin treatments prevented the significant increase of glutathione peroxidase, superoxide dismutase, glutathione reductase and catalase activities induced by tert-butyl hydroperoxide. Gene expression of antioxidant enzymes was also affected by the treatment with the polyphenol. The results of the biomarkers analyzed clearly show that treatment of HepG2 cells in culture with the natural dietary antioxidant quercetin strongly protects the cells against an oxidative insult

Isotope effects and the temperature dependences of the hyperfine coupling constants of muoniated sec-butyl radicals in condensed phases.

Science.gov (United States)

Fleming, Donald G; Bridges, Michael D; Arseneau, Donald J; Chen, Ya Kun; Wang, Yan Alexander

2011-04-07

Reported here is the first μSR study of the muon (A(μ)) and proton (A(p)) β-hyperfine coupling constants (Hfcc) of muoniated sec-butyl radicals, formed by muonium (Mu) addition to 1-butene and to cis- and trans-2-butene. The data are compared with in vacuo spin-unrestricted MP2 and hybrid DFT/B3YLP calculations reported in the previous paper (I), which played an important part in the interpretation of the data. The T-dependences of both the (reduced) muon, A(μ)′(T), and proton, A(p)(T), Hfcc are surprisingly well explained by a simple model, in which the calculated Hfcc from paper I at energy minima of 0 and near ±120° are thermally averaged, assuming an energy dependence given by a basic 2-fold torsional potential. Fitted torsional barriers to A(μ)′(T) from this model are similar (~3 kJ/mol) for all muoniated butyl radicals, suggesting that these are dominated by ZPE effects arising from the C−Mu bond, but for A(p)(T) exhibit wide variations depending on environment. For the cis- and trans-2-butyl radicals formed from 2-butene, A(μ)′(T) exhibits clear discontinuities at bulk butene melting points, evidence for molecular interactions enhancing these muon Hfcc in the environment of the solid state, similar to that found in earlier reports for muoniated tert-butyl. In contrast, for Mu−sec-butyl formed from 1-butene, there is no such discontinuity. The muon hfcc for the trans-2-butyl radical are seemingly very well predicted by B3LYP calculations in the solid phase, but for sec-butyl from 1-butene, showing the absence of further interactions, much better agreement is found with the MP2 calculations across the whole temperature range. Examples of large proton Hfcc near 0 K are also reported, due to eclipsed C−H bonds, in like manner to C−Mu, which then also exhibit clear discontinuities in A(p)(T) at bulk melting points. The data suggest that the good agreement found between theory and experiment from the B3LYP calculations for eclipsed bonds in

Acute and Developmental Behavioral Effects of Flame ...

Science.gov (United States)

As polybrominated diphenyl ethers are phased out, numerous compounds are emerging as potential replacement flame retardants for use in consumer and electronic products. Little is known, however, about the neurobehavioral toxicity of these replacements. This study evaluated the neurobehavioral effects of acute or developmental exposure to t-butylphenyl diphenyl phosphate (BPDP), 2-ethylhexyl diphenyl phosphate (EHDP), isodecyl diphenyl phosphate (IDDP), isopropylated phenyl phosphate (IPP), tricresyl phosphate (TMPP; also abbreviated TCP), triphenyl phosphate (TPHP; also abbreviated TPP), tetrabromobisphenol A (TBBPA), tris (2-chloroethyl) phosphate (TCEP), tris (1,3-dichloroisopropyl) phosphate (TDCIPP; also abbreviated TDCPP), tri-o-cresyl phosphate (TOCP), and 2,2-,4,4’-tetrabromodiphenyl ether (BDE-47) in zebrafish (Danio rerio) larvae. Larvae (n≈24 per dose per compound) were exposed to test compounds (0.4 - 120 µM) at sub-teratogenic concentrations either developmentally or acutely, and locomotor activity was assessed at 6 days post fertilization. When given developmentally, all chemicals except BPDP, IDDP and TBBPA produced behavioral effects. When given acutely, all chemicals produced behavioral effects, with TPHP, TBBPA, EHDP, IPP, and BPDP eliciting the most effects at the most concentrations. The results indicate that these replacement flame retardants may have developmental or pharmacological effects on the vertebrate nervous system. This study

Solution of a gallstone with methyl-tertiary butyl ether

Energy Technology Data Exchange (ETDEWEB)

Brambs, H J; Roeren, T; Holstege, A; Raedecke, J

1987-08-01

Methyl-t-butyl ether is a new agent to dissolve gallstones. The substance proves to be very successful and acts very rapidly. A percutaneous transhepatic drainage supplies an adequate access route to dissolve calculi within the bile ducts. We report the case of a patient where before insertion of an internal stent a stone in the common bile duct was dissolved within 3 1/2 hours.

Performance of pineapple slips inoculated with diazotrophic phosphate-solubilizing bacteria and rock phosphate

Directory of Open Access Journals (Sweden)

Lílian Estrela Borges Baldotto

2014-06-01

Full Text Available Besides fixing N2, some diazotrophic bacteria or diazotrophs, also synthesize organic acids and are able to solubilize rock phosphates, increasing the availability of P for plants. The application of these bacteria to pineapple leaf axils in combination with rock phosphate could increase N and P availability for the crop, due to the bacterial activity of biological nitrogen fixation and phosphate solubilization. The objectives of this study were: (i to select and characterize diazotrophs able to solubilize phosphates in vitro and (ii evaluate the initial performance of the pineapple cultivars Imperial and Pérola in response to inoculation with selected bacteria in combination with rock phosphate. The experiments were conducted at Universidade Estadual do Norte Fluminense Darcy Ribeiro, in 2009. In the treatments with bacteria the leaf contents of N, P and K were higher than those of the controls, followed by an increase in plant growth. These results indicate that the combined application of diazotrophic phosphate-solubilizing bacteria Burkholderia together with Araxá rock phosphate can be used to improve the initial performance of pineapple slips.

How do arbuscular mycorrhizal fungi handle phosphate? New insight into fine-tuning of phosphate metabolism.

Science.gov (United States)

Ezawa, Tatsuhiro; Saito, Katsuharu

2018-04-27

Contents Summary I. Introduction II. Foraging for phosphate III. Fine-tuning of phosphate homeostasis IV. The frontiers: phosphate translocation and export V. Conclusions and outlook Acknowledgements References SUMMARY: Arbuscular mycorrhizal fungi form symbiotic associations with most land plants and deliver mineral nutrients, in particular phosphate, to the host. Therefore, understanding the mechanisms of phosphate acquisition and delivery in the fungi is critical for full appreciation of the mutualism in this association. Here, we provide updates on physical, chemical, and biological strategies of the fungi for phosphate acquisition, including interactions with phosphate-solubilizing bacteria, and those on the regulatory mechanisms of phosphate homeostasis based on resurveys of published genome sequences and a transcriptome with reference to the latest findings in a model fungus. For the mechanisms underlying phosphate translocation and export to the host, which are major research frontiers in this field, not only recent advances but also testable hypotheses are proposed. Lastly, we briefly discuss applicability of the latest tools to gene silencing in the fungi, which will be breakthrough techniques for comprehensive understanding of the molecular basis of fungal phosphate metabolism. © 2018 The Authors. New Phytologist © 2018 New Phytologist Trust.

EFFICACY OF HYOSCINE BUTYL BROMIDE SUPPOSITORY FOR POSTOPERATIVE PAIN RELIEF

Directory of Open Access Journals (Sweden)

Soniya C. Alphonse

2017-07-01

Full Text Available BACKGROUND Caesarean Section is on the rise all over the world. Women undergoing Caesarean section often wish to be awake post operatively and to avoid excessive medications affecting interactions with the new born infant. Multimodal pain therapy has been advocated for postoperative pain management after caesarean section. MATERIALS AND METHODS The study is a prospective randomized controlled study conducted at a tertiary care hospital to study the effect of Hyoscine Butyl Bromide Suppositories for postoperative analgesia following elective repeat caesarean section. The study included sixty patients divided into two groups- Group1 (study group were given Hyoscine Butyl Bromide Suppository (10 mg along with Injection. Tramadol 50 mg IM and Group II (control group were given Injection Tramadol IM only at the end of surgery. Pain score of the patient assessed at 1 hr, 2 hrs, 6hrs and 24 hrs post operatively. The total no of doses of injection tramadol needed in 24 hrs and the interval between 1st and 2nd dose of tramadol was also noted. The adverse effects of the drug and additional advantages of the drug if any were also assessed. RESULTS There was no statistically significant difference in pain score during the assessment intervals between the two groups. There was no difference in the number of doses of tramadol needed in the first 24 hrs. The mean interval between the 1st and 2nd dose of tramadol was found to be 7.6538 hours for group 1 patients and 6.9130 for group patients which was found to be statistically significant. There was no statistically significant side effects/ additional advantages for the drugs. CONCLUSION Concurrent administration of Hyoscine Butyl Bromide Suppository (10 mg and injection Tramadol 50 mg IM offers a longer postoperative analgesia without any increased adverse effects.

Importance of Relativistic Effects and Electron Correlation in Structure Factors and Electron Density of Diphenyl Mercury and Triphenyl Bismuth.

Science.gov (United States)

Bučinský, Lukáš; Jayatilaka, Dylan; Grabowsky, Simon

2016-08-25

This study investigates the possibility of detecting relativistic effects and electron correlation in single-crystal X-ray diffraction experiments using the examples of diphenyl mercury (HgPh2) and triphenyl bismuth (BiPh3). In detail, the importance of electron correlation (ECORR), relativistic effects (REL) [distinguishing between total, scalar and spin-orbit (SO) coupling relativistic effects] and picture change error (PCE) on the theoretical electron density, its topology and its Laplacian using infinite order two component (IOTC) wave functions is discussed. This is to develop an understanding of the order of magnitude and shape of these different effects as they manifest in the electron density. Subsequently, the same effects are considered for the theoretical structure factors. It becomes clear that SO and PCE are negligible, but ECORR and scalar REL are important in low- and medium-order reflections on absolute and relative scales-not in the high-order region. As a further step, Hirshfeld atom refinement (HAR) and subsequent X-ray constrained wavefunction (XCW) fitting have been performed for the compound HgPh2 with various relativistic and nonrelativistic wave functions against the experimental structure factors. IOTC calculations of theoretical structure factors and relativistic HAR as well as relativistic XCW fitting are presented for the first time, accounting for both scalar and spin-orbit relativistic effects.

Formulation of single super phosphate fertilizer from rock phosphate of Hazara, Pakistan

Directory of Open Access Journals (Sweden)

Matiullah Khan

2012-05-01

Full Text Available Phosphorus deficiency is wide spread in soils of Pakistan. It is imperative to explore the potential and economics of indigenous Hazara rock phosphate for preparation of single super phosphate fertilizer. For the subject study rock phosphate was collected from Hazara area ground at 160 mesh level with 26% total P2O5 content for manual preparation of single super phosphate fertilizer. The rock phosphate was treated with various concentrations of sulfuric acid (98.9%, diluted or pure in the field. The treatments comprised of 20 and 35% pure acid and diluted with acid-water ratios of 1:5, 1:2, 1:1 and 2:1 v/v for acidulation at the rate of 60 liters 100 kg-1 rock phosphate. The amount was prior calculated in the laboratory for complete wetting of rock phosphate. A quantity of 150 kg rock phosphate was taken as treatment. The respective amount of acid was applied with the spray pump of stainless steel or poured with bucket. After proper processing, chemical analysis of the products showed a range of available P2O5 content from 9.56 to 19.24% depending upon the amount of acid and its dilution. The results reveal at that 1:1 dilutions gave the highest P2O5 content (19.24%, lowest free acid (6 % and 32% weight increase. The application of acid beyond or below this combination either pure or diluted gave hygroscopic product and higher free acids. The cost incurred upon the manual processing was almost half the prevailing rates in the market. These results lead to conclude that application of sulfuric acid at the rate of 60 liters 100 kg-1 with the dilution of 50% (v/v can yield better kind of SSP from Hazara rock phosphate at lower prices.

Effect of Anion on Behaviour of Li-S Battery Electrolyte Solutions Based on N-Methyl-N-Butyl-Pyrrolidinium Ionic Liquids

International Nuclear Information System (INIS)

Barghamadi, Marzieh; Best, Adam S.; Bhatt, Anand I.; Hollenkamp, Anthony F.; Mahon, Peter J.; Musameh, Mustafa; Rüther, Thomas

2015-01-01

The electrochemical behaviour and electrical performance are investigated for a series of lithium-sulfur (Li-S) cells in which the electrolyte solutions are organic solvent-ionic liquid mixtures that are based on the 1-butyl-1-methylpyrrolidinium (C 4 mpyr) cation with a range of anions. In each case, performance is compared with cells that are based on a standard mixed-ether organic electrolyte. The capacity of cells assembled with electrolytes containing 1-butyl-1-methylpyrrolidinium tris(pentafluoroethyl) trifluorophosphate (C 4 mpyr-FAP), 1-butyl-1-methylpyrrolidinium trifluoromethanesulfonate (C 4 mpyr-OTf), or 1-butyl-1-methylpyrrolidinium tricyanomethanide (C 4 mpyr-TCM) decline rapidly due to low conductivity, high polysulfide solubility and side reaction of electrolyte with electrodes, respectively. Our results confirm that polysulfide solubility is strongly controlled by the anion of the ionic liquid and verify that not all ionic liquids decrease polysulfide solubility. In agreement with previous reports, 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl) imide (C 4 mpyr-TFSI) shows the best compatibility in Li-S batteries and has a higher coulombic efficiency of greater than 99% over 100 cycles. Furthermore, impedance spectroscopy confirms that electrolyte composition influences the SEI layer formed on the lithium anode and its subsequent impedance.

Integrated assessment of the phosphate industry

International Nuclear Information System (INIS)

Ryan, M.T.; Cotter, S.J.

1980-05-01

The phosphate industry in the United States includes three major activities, namely, mining and milling of phosphate rock, phosphate product manufacture, and phosphate product use. Phosphatic materials contain uranium, thorium, and their decay products in greater than background amounts. This assessment of the radiological impacts associated with the redistribution of radioactive components of phosphate materials may provide insight into the effects of uranium extraction from phosphate materials for use in the nuclear fuel cycle

Role of Phosphate Transport System Component PstB1 in Phosphate Internalization by Nostoc punctiforme.

Science.gov (United States)

Hudek, L; Premachandra, D; Webster, W A J; Bräu, L

2016-11-01

In bacteria, limited phosphate availability promotes the synthesis of active uptake systems, such as the Pst phosphate transport system. To understand the mechanisms that facilitate phosphate accumulation in the cyanobacterium Nostoc punctiforme, phosphate transport systems were identified, revealing a redundancy of Pst phosphate uptake systems that exists across three distinct operons. Four separate PstB system components were identified. pstB1 was determined to be a suitable target for creating phenotypic mutations that could result in the accumulation of excessive levels of phosphate through its overexpression or in a reduction of the capacity to accumulate phosphate through its deletion. Using quantitative real-time PCR (qPCR), it was determined that pstB1 mRNA levels increased significantly over 64 h in cells cultured in 0 mM added phosphate and decreased significantly in cells exposed to high (12.8 mM) phosphate concentrations compared to the level in cells cultured under normal (0.8 mM) conditions. Possible compensation for the loss of PstB1 was observed when pstB2, pstB3, and pstB4 mRNA levels increased, particularly in cells starved of phosphate. The overexpression of pstB1 increased phosphate uptake by N. punctiforme and was shown to functionally complement the loss of PstB in E. coli PstB knockout (PstB - ) mutants. The knockout of pstB1 in N. punctiforme did not have a significant effect on cellular phosphate accumulation or growth for the most part, which is attributed to the compensation for the loss of PstB1 by alterations in the pstB2, pstB3, and pstB4 mRNA levels. This study provides novel in vivo evidence that PstB1 plays a functional role in phosphate uptake in N. punctiforme IMPORTANCE: Cyanobacteria have been evolving over 3.5 billion years and have become highly adept at growing under limiting nutrient levels. Phosphate is crucial for the survival and prosperity of all organisms. In bacteria, limited phosphate availability promotes the

Effects of education on low-phosphate diet and phosphate binder intake to control serum phosphate among maintenance hemodialysis patients: A randomized controlled trial

Directory of Open Access Journals (Sweden)

Eunsoo Lim

2018-03-01

Full Text Available Background : For phosphate control, patient education is essential due to the limited clearance of phosphate by dialysis. However, well-designed randomized controlled trials about dietary and phosphate binder education have been scarce. Methods : We enrolled maintenance hemodialysis patients and randomized them into an education group (n = 48 or a control group (n = 22. We assessed the patients' drug compliance and their knowledge about the phosphate binder using a questionnaire. Results : The primary goal was to increase the number of patients who reached a calcium-phosphorus product of lower than 55. In the education group, 36 (75.0% patients achieved the primary goal, as compared with 16 (72.7% in the control group (P = 0.430. The education increased the proportion of patients who properly took the phosphate binder (22.9% vs. 3.5%, P = 0.087, but not to statistical significance. Education did not affect the amount of dietary phosphate intake per body weight (education vs. control: -1.18 ± 3.54 vs. -0.88 ± 2.04 mg/kg, P = 0.851. However, the dietary phosphate-to-protein ratio tended to be lower in the education group (-0.64 ± 2.04 vs. 0.65 ± 3.55, P = 0.193. The education on phosphate restriction affected neither the Patient-Generated Subjective Global Assessment score (0.17 ± 4.58 vs. -0.86 ± 3.86, P = 0.363 nor the level of dietary protein intake (-0.03 ± 0.33 vs. -0.09 ± 0.18, P = 0.569. Conclusion : Education did not affect the calcium-phosphate product. Education on the proper timing of phosphate binder intake and the dietary phosphate-to-protein ratio showed marginal efficacy.

A Study of the Teratogenicity of Butylated Hydroxyanisole on Rabbits

DEFF Research Database (Denmark)

Hansen, Ernst; Meyer, Otto A.

1978-01-01

A teratogenicity study on butylated hydroxyanisole (BHA) was carried out in SPF New Zealand White rabbits. BHA was given by gavage from day 7–18 of the gestation period in doses of 0, 50, 200 and 400 mg/kg body wt./day. The fetuses were removed on day 28. No effect related to the treatment with BHA...

Recanalization of Splenic Artery Aneurysm After Transcatheter Arterial Embolization Using N-Butyl Cyanoacrylate

International Nuclear Information System (INIS)

Matsumoto, Keiji; Ushijima, Yasuhiro; Tajima, Tsuyoshi; Nishie, Akihiro; Hirakawa, Masakazu; Ishigami, Kousei; Yamaji, Yukiko; Honda, Hiroshi

2010-01-01

A 65-year-old woman who had been diagnosed as having microscopic polyangiitis developed sudden abdominal pain and entered a state of shock. Abdominal CT showed massive hemoperitoneum, and emergent angiography revealed a ruptured splenic artery aneurysm. After direct catheterization attempts failed due to tortuous vessels and angiospasm, transcatheter arterial embolization using an n-butyl cyanoacrylate (NBCA)-lipiodol mixture was successfully performed. Fifty days later, the patient developed sudden abdominal pain again. Repeated angiography demonstrated recanalization of the splenic artery and splenic artery aneurysm. This time, the recanalized aneurysm was embolized using metallic coils with the isolation method. Physicians should keep in mind that recanalization can occur after transcatheter arterial embolization using N-butyl cyanoacrylate, which has been used as a permanent embolic agent.

Zinc phosphate conversion coatings

Science.gov (United States)

Sugama, Toshifumi

1997-01-01

Zinc phosphate conversion coatings for producing metals which exhibit enhanced corrosion prevention characteristics are prepared by the addition of a transition-metal-compound promoter comprising a manganese, iron, cobalt, nickel, or copper compound and an electrolyte such as polyacrylic acid, polymethacrylic acid, polyitaconic acid and poly-L-glutamic acid to a phosphating solution. These coatings are further improved by the incorporation of Fe ions. Thermal treatment of zinc phosphate coatings to generate .alpha.-phase anhydrous zinc phosphate improves the corrosion prevention qualities of the resulting coated metal.

Study of the butyl acetate synthesis - 1. Catalyst selection

Directory of Open Access Journals (Sweden)

Álvaro Orjuela Londoño

2004-01-01

Full Text Available In this work, a laboratory scale selection study over eight catalytic agents was made, in the acetic acid and butyl alcohol esterification reaction (seven lon exchange resins and a zeolytic solid. Considering some physicochemical characteristics as the activation pre-treating requirements, acidity, thermal stability, reaction performance, etc., it was found that macroporous ion exchange resins are the most efficient catalysts, especially Lewatit K-2431 resin.

Standard thermochemical characteristics of combustion and formation of 3,5-di-tert-butyl-o-benzoquinone and 3,6-di-tert-butyl-o-benzoquinone at T = 298.15 K

International Nuclear Information System (INIS)

Pashanova, Kira I.; Abakumov, Gleb A.; Markin, Alexey V.; Piskunov, Alexander V.; Smirnova, Natalia N.

2016-01-01

Highlights: • We report the results of thermochemical study for benzoquinone derivatives. • Optimal conditions for determination of combustion energy for benzoquinone were done. • The formation enthalpies for crystalline benzoquinone have been detected at T = 298.15 K. • The formation enthalpy of isomeric quinones were compared. - Abstract: Optimal conditions for investigations of thermodynamic properties have been determined experimentally by the method of combustion calorimetry for compounds of the o-benzoquinone series. In the present work, the energies of combustion in oxygen were measured at T = 298.15 K by static bomb combustion calorimetry for 3,5-di-tert-butyl-o-benzoquinone and 3,6-di-tert-butyl-o-benzoquinone. The experimental values have been used to calculate the standard (p° = 0.1 MPa) molar enthalpy of combustion Δ_cH"o_m and formation Δ_fH"o_m for the examined compounds in the crystalline phase.

Hemodialysis for near-fatal sodium phosphate toxicity in a child receiving sodium phosphate enemas.

Science.gov (United States)

Becknell, Brian; Smoyer, William E; O'Brien, Nicole F

2014-11-01

This study aimed to demonstrate the importance of considering hemodialysis as a treatment option in the management of sodium phosphate toxicity. This is a case report of a 4-year-old who presented to the emergency department with shock, decreased mental status, seizures, and tetany due to sodium phosphate toxicity from sodium phosphate enemas. Traditional management of hyperphosphatemia with aggressive hydration and diuretics was insufficient to reverse the hemodynamic and neurological abnormalities in this child. This is the first report of the use of hemodialysis in a child without preexisting renal failure for the successful management of near-fatal sodium phosphate toxicity. Hemodialysis can safely be used as an adjunctive therapy in sodium phosphate toxicity to rapidly reduce serum phosphate levels and increase serum calcium levels in children not responding to conventional management.

Inducing PLA/starch compatibility through butyl-etherification of waxy and high amylose starch

CSIR Research Space (South Africa)

Wokadala, OC

2014-06-01

Full Text Available In this study, waxy and high amylose starches were modified through butyl-etherification to facilitatecompatibility with polylactide (PLA). Fourier transform infrared spectroscopy, proton nuclear magneticresonance spectroscopy and wettability tests...

Phosphate transporter mediated lipid accumulation in Saccharomyces cerevisiae under phosphate starvation conditions.

Science.gov (United States)

James, Antoni W; Nachiappan, Vasanthi

2014-01-01

In the current study, when phosphate transporters pho88 and pho86 were knocked out they resulted in significant accumulation (84% and 43%) of triacylglycerol (TAG) during phosphate starvation. However in the presence of phosphate, TAG accumulation was only around 45% in both pho88 and pho86 mutant cells. These observations were confirmed by radio-labeling, fluorescent microscope and RT-PCR studies. The TAG synthesizing genes encoding for acyltransferases namely LRO1 and DGA1 were up regulated. This is the first report for accumulation of TAG in pho88Δ and pho86Δ cells under phosphate starvation conditions. Copyright © 2013. Published by Elsevier Ltd.

PHYSIOLOGICALLY BASED PHARMACOKINETIC MODEL FOR HUMAN EXPOSURES TO METHYL TERTIARY-BUTYL ETHER

Science.gov (United States)

Humans can be exposed by inhalation, ingestion, or dermal absorption to methyl tertiary-butyl ether (MTBE), an oxygenated fuel additive, from contaminated water sources. The purpose of this research was to develop a physiologically based pharmacokinetic model describing in human...

IRIS Toxicological Review of Tert-Butyl Alcohol (Tert-Butanol) (External Review Draft)

Science.gov (United States)

The IRIS Toxicological Review of tert-Butyl Alcohol (tert-Butanol) was released for external peer review in June 2017. EPA’s Science Advisory Board’s (SAB) Chemical Assessment Advisory Committee (CAAC) will conduct a peer review of the scientific basis supporting ...

IRIS Toxicological Review of Tert-Butyl Alcohol (Tert-Butanol) (Public Comment Draft)

Science.gov (United States)

EPA is developing an Integrated Risk Information System (IRIS) assessment of tert-butyl Alcohol (tert-butanol) and has released the public comment draft assessment for public comment and external peer review. When final, the assessment will appear on the IRIS databa...

IRIS Toxicological Review of Ethyl Tertiary Butyl Ether (ETBE) (Public Comment Draft)

Science.gov (United States)

In September 2016, the U.S. Environmental Protection Agency's (USEPA) released the draft Integrated Risk Information System (IRIS) Toxicological Review of Ethyl Tertiary Butyl Ether (ETBE). Consistent with the 2013 IRIS Enhancements, draft IRIS assessments are released prior to e...

Determination of dibutylphosphate and monobutylphosphate in TBP by ion chromatography

International Nuclear Information System (INIS)

Siva Kumar, B.; Vijayalakshmi, S.; Sankaran, K.; Ganesan, V.

2012-01-01

Tri-n-butyl phosphate (TBP) is used as solvent in the PUREX (Plutonium Uranium Refining by Extraction) process of nuclear fuel reprocessing. TBP undergoes chemical and radiological degradation to give DBP and MBP which in turn extracts the heavy metal such as U, Pu thereby affecting the performance of the extraction process. Analytical method using ion chromatography (IC) was developed for the determination of dibutyl phosphate (DBP) and monobutyl phosphate (MBP) in TBP. In this method, DBP and MBP were extracted from tri-n-butyl phosphate using carbonate-bicarbonate mixture of eluent composition and the aqueous phase was analyzed using suppressed ion chromatography employing carbonate as eluent. Standardization of extraction was carried out by standard addition studies. The detection limits for both DBP and MBP are found to be in sub ppm level. This method was applied to the analysis of TBP supplied by different suppliers

21 CFR 137.175 - Phosphated flour.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Phosphated flour. 137.175 Section 137.175 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Related Products § 137.175 Phosphated flour. Phosphated flour, phosphated white flour, and phosphated...

Poly (ethylene oxide)-block-poly (n-butyl acrylate)-blockpoly (acrylic acid) triblock terpolymers with highly asymmetric hydrophilic blocks: synthesis and aqueous solution properties

OpenAIRE

Petrov, P. (Petar); Yoncheva, K. (Krassimira); Mokreva, P. (Pavlina); Konstantinov, S. (Spiro); Irache, J.M. (Juan Manuel); Müller, A.H.E. (Axel H.E.)

2013-01-01

The synthesis and aggregation behaviour in aqueous media of novel amphiphilic poly(ethylene oxide)- block-poly(n-butyl acrylate)-block-poly(acrylic acid) (PEO–PnBA–PAA) triblock terpolymers were studied. Terpolymers composed of two highly asymmetric hydrophilic PEO (113 monomer units) and PAA (10–17 units) blocks, and a longer soft hydrophobic PnBA block (163 or 223 units) were synthesized by atom transfer radical polymerisation (ATRP) of n-butyl acrylate and tert-butyl acrylate ...

IRIS Toxicological Review of Ethylene Glycol Mono-Butyl ...

Science.gov (United States)

EPA released the draft report, Toxicological Review for Ethylene Glycol Mono-Butyl Ether , that was distributed to Federal agencies and White House Offices for comment during the Science Discussion step of the IRIS Assessment Development Process. Comments received from other Federal agencies and White House Offices are provided below with external peer review panel comments. EPA is conducting a peer review of the scientific basis supporting the human health hazard and dose-response assessment of EGBE that will appear on the Integrated Risk Information System (IRIS) database.

Critical behavior in the system cyclopentanone + water + secondary butyl alcohol

Science.gov (United States)

Krishna, U. Santhi; Unni, P. K. Madhavan

2018-05-01

We report detailed measurements of coexistence surface in the ternary system cylcopentanone + water + secondary butyl alcohol. The coexistence surface is seen to have an unusual tunnel like feature and is a potential system in which special critical points such as the Quadruple Critical Point (QCP) could be studied. Analysis of coexistence curves indicates that the system shows 3D-Ising like critical behavior.

Di-iso-Butyl Phthalate MATERNAL AND FETAL DATA FROM ...

Science.gov (United States)

this file contains the raw data on the effects of in utero administration of di-iso-butyl phthalate on maternal weight gain during dosing and the numbers of fetuses and fetal resorptions. The data have all been previously published, as described on the file metadata sheet. Raw data file from our published studies on DIBP specifically requested (6/14/2016) by NCEA scientists for analysis and inclusion in their assessment of this chemical.

Use of triphenyl phosphate as risk mitigant for metal amide hydrogen storage materials

Science.gov (United States)

Cortes-Concepcion, Jose A.; Anton, Donald L.

2016-04-26

A process in a resulting product of the process in which a hydrogen storage metal amide is modified by a ball milling process using an additive of TPP. The resulting product provides for a hydrogen storage metal amide having a coating that renders the hydrogen storage metal amide resistant to air, ambient moisture, and liquid water while improving useful hydrogen storage and release kinetics.

IRIS Toxicological Review of Ethylene Glycol Mono Butyl Ether (Egbe) (Final Report)

Science.gov (United States)

EPA has finalized the Toxicological Review of Ethylene Glycol Mono Butyl Ether: in support of the Integrated Risk Information System (IRIS). Now final, this assessment may be used by EPA’s program and regional offices to inform decisions to protect human health.

A thermal lensing study of a photolysis of di- t-butyl peroxide

Science.gov (United States)

Fuke, K.; Hasegawa, A.; Ueda, M.; Itoh, M.

1981-11-01

A photolysis of di- t-butyl peroxide (BOOB) was studied by using a thermal lensing technique. This technique is found to be applicable to the determination Of the rate Constants of the decay of t-butoxy radical (BO ) and the hydrogen abstraction reaction.

2-tert-Butyl-5,6,7,8,9,10-hexahydrocyclohepta[b]indole

Directory of Open Access Journals (Sweden)

Janina Wobbe

2011-09-01

Full Text Available 2-tert-Butyl-5,6,7,8,9,10-hexahydrocyclohepta[b]indole was synthesized by reaction of cycloheptanone and (4-tert-butylphenylhydrazine hydrochloride in the presence of sodium acetate and sulfuric acid in glacial acetic acid via Fischer indole synthesis.

IRIS Toxicological Review of Ethyl Tertiary Butyl Ether (ETBE) (External Review Draft)

Science.gov (United States)

The IRIS Toxicological Review of Ethyl Tertiary Butyl Ether (ETBE) was released for external peer review in June 2017. EPA’s Science Advisory Board’s (SAB) Chemical Assessment Advisory Committee (CAAC) will conduct a peer review of the scientific basis supporting the ETB...

Supercritical fluid extraction of uranium and thorium from nitric acid medium using organophosphorous compounds

Energy Technology Data Exchange (ETDEWEB)

Pitchaiah, K.C.; Sujatha, K.; Rao, C.V.S. Brahmmananda; Subramaniam, S.; Sivaraman, N.; Rao, P.R. Vasudeva [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Chemistry Group

2015-06-01

In recent years, Supercritical Fluid Extraction (SFE) technique has been widely used for the extraction of metal ions. In the present study, extraction of uranium from nitric acid medium was investigated using supercritical carbon dioxide (Sc-CO{sub 2}) containing various organophosphorous compounds such as trialkyl phosphates e.g. tri-iso-amyl phosphate (TiAP), tri-sec-butyl phosphate (TsBP) and tri-n-butyl phosphate (TBP), dialkylalkyl phosphonates, e.g. diamylamyl phosphonate (DAAP) and dibutyl butyl phosphonate (DBBP), dialkyl hydrogen phosphonates, e.g. dioctyl hydrogen phosphonate (DOHP), dioctylphosphineoxide (DOPO), trioctyl phosphine oxide (TOPO), n-octylphenyl N,N-diisobutyl carbamoylmethylphosphine oxide (CMPO) and di-2-ethyl-hexyl phosphoric acid (HDEHP). Some of these ligands have been investigated for the first time in the supercritical phase for the extraction of uranium. The extraction efficiency of uranium was studied with TiAP, DAAP and DBBP as a function of nitric acid concentration; the kinetics of the equilibration period (static extraction) and transportation of the metal complex (dynamic extraction) was investigated. The influence of pressure and temperature on the extraction behaviour of uranium with DAAP was studied from 4 N HNO{sub 3}. The extraction efficiency of uranium from 4 N nitric acid medium was found to increase in the order of phosphates < phosphonates < HDEHP < TOPO < CMPO. In the case of phosphates and phosphonates, the maximum extraction of uranium was found to be from 4 N HNO{sub 3} medium. The acidic extractants, HDEHP and DOHP showed relatively higher extraction at lower acidities. The relative extraction of uranium and thorium from their mixture was also examined using Sc-CO{sub 2} containing phosphates, phosphonates and TOPO. The ligand, TsBP provided better fractionation between uranium and thorium compared to trialkyl phosphates, dialkyl alkyl phosphonates and TOPO.

40 CFR 721.10193 - 1-Butanaminium, N-(3-aminopropyl)-N-butyl-N-(2-carboxyethyl)-, N-coco acyl derivs., inner salts.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1-Butanaminium, N-(3-aminopropyl)-N...-aminopropyl)-N-butyl-N-(2-carboxyethyl)-, N-coco acyl derivs., inner salts. (a) Chemical substance and...-aminopropyl)-N-butyl-N-(2-carboxyethyl)-, N-coco acyl derivs., inner salts (PMN P-06-263, Chemical B; CAS No...

Catalytic Upgrading of Biomass-Derived Furfuryl Alcohol to Butyl Levulinate Biofuel over Common Metal Salts

Directory of Open Access Journals (Sweden)

Lincai Peng

2016-09-01

Full Text Available Levulinate ester has been identified as a promising renewable fuel additive and platform chemical. Here, the use of a wide range of common metal salts as acid catalysts for catalytic upgrading of biomass-derived furfuryl alcohol to butyl levulinate was explored by conventional heating. Both alkali and alkaline earth metal chlorides did not lead effectively to the conversion of furfuryl alcohol, while several transition metal chlorides (CrCl3, FeCl3, and CuCl2 and AlCl3 exhibited catalytic activity for the synthesis of butyl levulinate. For their sulfates (Cr(III, Fe(III, Cu(II, and Al(III, the catalytic activity was low. The reaction performance was correlated with the Brønsted acidity of the reaction system derived from the hydrolysis/alcoholysis of cations, but was more dependent on the Lewis acidity from the metal salts. Among these investigated metal salts, CuCl2 was found to be uniquely effective, leading to the conversion of furfuryl alcohol to butyl levulinate with an optimized yield of 95%. Moreover, CuCl2 could be recovered efficiently from the resulting reaction mixture and remained with almost unchanged catalytic activity in multiple recycling runs.

Actinide-carbon bonds: insertion reactions of carbon monoxide, tert-butyl isocyanide, and tert-butyl cyanide into [(Me3Si)2N]2MCH2Si(Me)2NSiMe3

International Nuclear Information System (INIS)

Simpson, S.J.; Andersen, R.A.

1981-01-01

The thorium or uranium metallacycles [(Me 2 Si) 2 N] 2 MCH 2 Si(Me) 2 NSiMe 3 (I) react with tert-butyl cyanide to give the six-membered ring compounds [(Me 3 Si) 2 N] 2 MN = C(t-Bu)CH 2 Si(Me) 2 NSiMe 3 . The metallacycles (I) also react with the isoelectronic molecules tert-butyl isocyanide and carbon monoxide to give the unique five-membered ring compounds with exocyclic carbon-carbon double bonds, [(Me 3 Si) 2 N] 2 MXC(=CH 2 )Si(Me) 2 NSiMe 3 , where X is t-BuN or oxygen. The four-membered ring metallacycles (I) give simple coordination complexes of the type [(Me 3 Si) 2 N] 2 MCH 2 Si-(Me) 2 NSiMe 3 (N 3 SiMe 3 ) with trimethylsilyl azide

Esterification for butyl butyrate formation using Candida cylindracea lipase produced from palm oil mill effluent supplemented medium

Directory of Open Access Journals (Sweden)

Aliyu Salihu

2014-12-01

Full Text Available The ability of Candida cylindracea lipase produced using palm oil mill effluent (POME as a basal medium to catalyze the esterification reaction for butyl butyrate formation was investigated. Butyric acid and n-butanol were used as substrates at different molar ratios. Different conversion yields were observed according to the affinity of the produced lipase toward the substrates. The n-butanol to butyric acid molar ratio of 8 and lipase concentration of 75 U/mg gave the highest butyl butyrate formation of 63.33% based on the statistical optimization using face centered central composite design (FCCCD after 12 h reaction. The esterification potential of the POME based lipase when compared with the commercial lipase from the same strain using the optimum levels was found to show a similar pattern. It can be concluded therefore that the produced lipase possesses appropriate characteristics to be used as a biocatalyst in the esterification reactions for butyl butyrate formation.

Analysing chemical equilibrium conditions when studying butyl acetate synthesis

OpenAIRE

Álvaro Orjuela Londoño; Fernando Leiva Lenis; Luis Alejandro Boyacá Mendivelso; Gerardo Rodríguez Niño; Luis María Carballo Suárez

2010-01-01

This work studied the liquid phase of acetic acid and butyl alcohol esterification reaction (P atm = 560 mmHg),using an ion exchange resin (Lewatit K-2431) as catalyst. A set of assays were carried out for determining the effect of catalyst load, temperature and molar ratio (acid/alcohol) on chemical equilibrium constant. Components’ selective sorption on the resin matrix was noticed; its effect on equilibrium conditions was verified, by using different acid/alcohol starting ratios. A non-ide...

The influence of n-butyl mercaptan on acrylic compounds obtained winder γ-gamma radiation

International Nuclear Information System (INIS)

Ribeiro, Marcos S.; Parra, Duclerc F.; Lugao, Ademar B.

2013-01-01

The chain transfer agents play a key role in the production of polymers, as they allow better control of their molecular weight, among other functions. For this reason we performed this study to perform an analysis on the influence of n-butyl mercaptan in the reaction of compounds of ethyl methacrylate by varying the density and shrinkage of the samples. In the present study can be seen that n-butyl mercaptan, acts as transfer agent, which influences the reaction kinetics of composite acrylic, since it presence in the compound increased average density and contraction average. It is also possible to minimize the variability of the compound density, even if they are altered. Final products with improved properties homogeneously could be obtained. (author)

Radiogaschromatographic analysis of volatile products of the photolysis of the system bis-(tributyltin)-oxide-(butyl-l-14C)/cellulose

International Nuclear Information System (INIS)

Kloetzer, D.; Goerner, H.; Heise, K.H.

1979-01-01

Apparatus and method for separation and identification of the products of photochemical decomposition in the system bis(tributyltin)-oxide-(butyl-1- 14 C)/cellulose are described. Ultraviolet radiation causes the formation of n-butane- 14 C and n-octane- 14 C, i.e. 14 C-labelled butyl radicals splitting off from the tin organic compound are stabilized by reactions with H atoms from the photodecomposition of cellulose or by dimerization. (author)

New evidence for primordial action site of Fluazifop-P-butyl on Acanthospermum hispidum seedlings: From the effects on chlorophyll fluorescence characteristics and histological observation.

Science.gov (United States)

Shang, Yuhong; Yang, Congjun; Liu, Zhihang; Song, Jiqing; Li, Pingliang; Li, Lingxu; Zhou, Fei; Xin, Hua; Wan, Fanghao; Matsumoto, Hiroshi; Luo, Xiaoyong

2017-10-01

Acanthospermum hispidum DC, an Asteraceae weed species, was very susceptible to fluazifop-P-butyl, but tolerant to other aryloxyphenoxypropionate herbicides, such as haloxyfop-P-methyl. However, other Asteraceae weeds including Bidens pilosa were all tolerant to fluazifop-P-butyl. Membrane lipid peroxidation by increasing the levels of reactive oxygen species (ROS) was proposed as an action mechanism of fluazifop-P-butyl in A. hispidum. To further clarify the primordial action site of fluazifop-P-butyl in this species, the effects on chlorophyll fluorescence characteristics and cytohistology of apical meristems were studied. Chlorophyll fluorescence characteristics (CFC) in sensitive A. hispidum seedlings were markedly affected by 10μM fluazifop-P-butyl, with the dark fluorescence yield (Fo), maximal fluorescence yield (Fm), maximal PS II quantum yield (Fv/Fm), effective photosystem II (PS II) quantum yield [Y(II)], and quantum yield of regulated energy dissipation [Y(NPQ)] declining, quantum yield of nonregulated energy dissipation [Y(NO)] rising, but these measures were not affected in Bidens pilosa. The effects of fluazifop-P-butyl on chlorophyll fluorescence properties were observed on the growing point before the mature leaves by about 4-6h. Haloxyfop-P-methyl, a control herbicide, had no effects on CFC of either A. hispidum or B. pilosa. In addition, damage to apical meristem cells of A. hispidum was observed at 6 HAT prior to changes in chlorophyll fluorescence parameters suggesting that the primary action site of fluazifop-P-butyl in this species is in the apical meristem and the effects on CFC may be the results of secondary action. Copyright © 2017 Elsevier Inc. All rights reserved.

Radioactivity of phosphate ores from Karatas-Mazidag phosphate deposit of Turkey

International Nuclear Information System (INIS)

Akyuez, T.; Varinlioglu, A.; Kose, A.; Akyuez, S.

2000-01-01

The specific activities of 238 U, 226 Ra, 232 Th and 40 K in the composite samples of phosphate ores of type I (grey-coloured ore, with high P 2 O 5 (21-35%) and low calcite content) and of type II (grey coloured calcite ore, with low P 2 O 5 content (5-17%)) of Karatas-Mazidag phosphate deposit, Turkey, have been determined by gamma spectrometry together with phosphatic animal feed ingredients. The concentrations of 238 U, 226 Ra, 232 Th and 40 K were found to be up to 557, 625, 26 and 297 Bq x kg -1 , respectively. Radium equivalent activities of samples were calculated and compared with those given in the literature. Uranium concentration of the individual phosphate samples, from which composite samples of ores of type I and II have been prepared, were found to show and increasing trend with increasing P 2 O 5 and F concentrations. (author)

Phosphate application to firing range soils for Pb immobilization: The unclear role of phosphate

International Nuclear Information System (INIS)

Chrysochoou, Maria; Dermatas, Dimitris; Grubb, Dennis G.

2007-01-01

Phosphate treatment has emerged as a widely accepted approach to immobilize Pb in contaminated soils and waste media, relying on the formation of the highly insoluble mineral pyromorphite as solubility-controlling phase for Pb. As such, phosphate treatment has been proposed as a Best Management Practice (BMP) for firing ranges where Pb occurs in its metallic forms and several other phases (carbonates, oxides). While pyromorphite thermodynamically has the potential to control Pb solubility at low levels, its formation is kinetically controlled by pH, the solubility of the phosphate source, and the solubility of Pb species. Treatability studies have shown that excess quantities of soluble and acidic phosphate sources, such as phosphoric acid, are necessary for successful in situ treatment. Even under these conditions, Extended X-ray Absorption Fine Structure (EXAFS), the only reliable method to identify and quantify Pb speciation, showed that Pb conversion to pyromorphite in in situ treated soils was less than 45% after 32 months. Furthermore, the use of lime (CaO) to restore soil pH in acidified soil treatments inhibited further conversion. Additionally, phosphate treatment is known to reduce bioavailability through pyromorphite formation in the intestinal tract, and the phytoaccumulation of Pb; both desirable effects for Pb-impacted areas. Given the costs of phosphate treatment, the use of biogenic phosphate sources, such as bone meal, may be a more environmentally sustainable approach toward this end. In the many studies focusing on phosphate treatment, the attendant P leaching and eutrophication have been largely overlooked, along with other issues such as the enhanced leaching of oxyanionic contaminants, such as Se, As and W. The success and sustainability of applying phosphate as a BMP in firing range soils therefore remain questionable

Method of stripping plutonium from tributyl phosphate solution which contains dibutyl phosphate-plutonium stable complexes

International Nuclear Information System (INIS)

Ochsenfeld, W.; Schmieder, H.

1976-01-01

Fast breeder fuel elements which have been highly burnt-up are reprocessed by extracting uranium and plutonium into an organic solution containing tributyl phosphate. The tributyl phosphate degenerates at least partially into dibutyl phosphate and monobutyl phosphate, which form stable complexes with tetravalent plutonium in the organic solution. This tetravalent plutonium is released from its complexed state and stripped into aqueous phase by contacting the organic solution with an aqueous phase containing tetravalent uranium. 6 claims, 1 drawing figure

IRIS Toxicological Review of Ethyl Tertiary Butyl Ether (ETBE) (External Review Draft, 2009)

Science.gov (United States)

EPA is conducting a peer review and public comment of the scientific basis supporting the human health hazard and dose-response assessment of ethyl tertiary butyl ether (ETBE) that when finalized will appear on the Integrated Risk Information System (IRIS) database.

Combined prenatal and postnatal butyl paraben exposure produces autism-like symptoms in offspring: comparison with valproic acid autistic model.

Science.gov (United States)

Ali, Elham H A; Elgoly, Amany H Mahmoud

2013-10-01

The aim of this work is to evaluate the impact of butyl paraben (BP) in brain of the pups developed for mothers administered BP from early pregnancy till weaning and its effect on studying the behavior, brain neurotransmitters and brain derived neurotrophic factor BDNF via comparing the results with valproic acid (VA) autistic-rat model preparing by a single oral injection dose of VA (800 mg/kg b.wt) at the 12.5 days of gestation. Butyl paraben was orally and subcutaneously administered (200 mg/kg b.wt) to pregnant rats from gestation day 1 to lactation day 21. The offspring male rats were subjected at the last 3 days of lactation to Morris water maze and three chamber sociability test then decapitated and the brain was excised and dissected to the cortex, hippocampus, cerebellum, midbrain and pons for the determination of norepinephrine, dopamine and serotonin (NE, DA and 5-HT) and cortex amino acids and whole brain BDNF. The results showed similar social and learning and memory behavioral deficits in VA rat model and the butyl paraben offspring in comparison with the controls. Also, some similar alterations were observed in monoamine content, amino acids and BDNF factor in the autistic-like model and butyl paraben offspring in comparison with the controls. The alterations were recorded notably in hippocampus and pons NE, midbrain DA, hippocampus and midbrain 5-HT, and frontal cortex GABA and asparagine. These data suggest that prenatal exposure to butyl paraben induced neuro-developmental disorders similar to some of the neurodevelopmental disorders observed in the VA model of autism. © 2013 Elsevier Inc. All rights reserved.

Assessment, measurement and correlation of (vapour + liquid) equilibrium of (carbon dioxide + butyl, isobutyl, and amyl formate) systems

International Nuclear Information System (INIS)

Shen, Yanshu; Zheng, Danxing; Li, Xinru; Li, Yun

2013-01-01

Highlights: • Selected three formates that have relative perfect absorption performance for CO 2 . • Measured the VLE data of CO 2 + butyl, isobutyl, and amyl formates systems. • Correlated the VLE data by using PR EOS with two mixing rules and SRK EOS with one mixing rule. • Concluded amyl formate has potential research value as CO 2 physical absorbent. -- Abstract: In this work, three formates (butyl, isobutyl, and amyl formate) were considered as relative perfect CO 2 absorption performance based on the excess Gibbs function as the thermodynamics criterion. An online static-analytical method was used to measure the (vapour + liquid) equilibrium (VLE) data for the CO 2 + butyl, isobutyl, and amyl formates under the pressure of (0.2 to 6) MPa and the temperatures at a range from (283.15 to 343.15) K. Then the VLE data were correlated by Peng–Robinson (PR) equation of state (EOS) with classic mixing rule, PR EOS with Wong–Sandler (WS) mixing rule and Soave–Redlich–Kwong (SRK) EOS with classic mixing rule. It is shown that SRK EOS is comparatively appropriate for CO 2 + butyl formate binary system. Both PR EOS with classic mixing rule and SRK EOS can be used to correlate the binary systems of CO 2 + isobutyl, amyl formate. It is found that the solubility order of three formates for CO 2 from high to low is arranged as CO 2 + amyl formate > CO 2 + butyl formate > CO 2 + isobutyl formate, showing the system of CO 2 + amyl formate has the best absorption performance. By comparison, it indicates that formates have a greater solubility for CO 2 than acetates on the condition of the same temperature and pressure. In addition, the thermophysical properties, mole absorption and mass absorptive amount of several industrial absorbents were assessed and the absorption performance of amyl formate for CO 2 is better than other physical absorbents. Thus, the study concluded that amyl formate has potential research value as physical absorbent for CO 2 capture

A Rare Case of Retrogastric Abscess Occurring Six Months after N-Butyl-2-Cyanoacrylate Injection into Gastric Varices

Directory of Open Access Journals (Sweden)

Ikram Hussain

2018-01-01

Full Text Available Background. Injection with N-butyl-2-cyanoacrylate is a proven and successful therapeutic modality for treatment of patients with bleeding gastric varices. However, a variety of complications have also been associated with its use. Here, we report a rare case of retrogastric abscess which occurred almost six months after this therapy. This abscess was attributed to the hampered microbial clearance caused by the venous obliterations from N-butyl-2-cyanoacrylate. The abscess was successfully treated with 3 months of antibiotics.

Phosphate control in dialysis

Directory of Open Access Journals (Sweden)

Cupisti A

2013-10-01

Full Text Available Adamasco Cupisti,1 Maurizio Gallieni,2 Maria Antonietta Rizzo,2 Stefania Caria,3 Mario Meola,4 Piergiorgio Bolasco31Department of Clinical and Experimental Medicine, University of Pisa, Pisa, Italy; 2Nephrology and Dialysis Unit, San Carlo Borromeo Hospital, Milan, Italy; 3Territorial Department of Nephrology and Dialysis, ASL Cagliari, Italy; 4Sant'Anna School of Advanced Studies, University of Pisa, Pisa, ItalyAbstract: Prevention and correction of hyperphosphatemia is a major goal of chronic kidney disease–mineral and bone disorder (CKD–MBD management, achievable through avoidance of a positive phosphate balance. To this aim, optimal dialysis removal, careful use of phosphate binders, and dietary phosphate control are needed to optimize the control of phosphate balance in well-nourished patients on a standard three-times-a-week hemodialysis schedule. Using a mixed diffusive–convective hemodialysis tecniques, and increasing the number and/or the duration of dialysis tecniques are all measures able to enhance phosphorus (P mass removal through dialysis. However, dialytic removal does not equal the high P intake linked to the high dietary protein requirement of dialysis patients; hence, the use of intestinal P binders is mandatory to reduce P net intestinal absorption. Unfortunately, even a large dose of P binders is able to bind approximately 200–300 mg of P on a daily basis, so it is evident that their efficacy is limited in the case of an uncontrolled dietary P load. Hence, limitation of dietary P intake is needed to reach the goal of neutral phosphate balance in dialysis, coupled to an adequate protein intake. To this aim, patients should be informed and educated to avoid foods that are naturally rich in phosphate and also processed food with P-containing preservatives. In addition, patients should preferentially choose food with a low P-to-protein ratio. For example, patients could choose egg white or protein from a vegetable source

Performance of pineapple slips inoculated with diazotrophic phosphate-solubilizing bacteria and rock phosphate

OpenAIRE

Lílian Estrela Borges Baldotto; Marihus Altoé Baldotto; Fábio Lopes Olivares; Adriane Nunes de Souza

2014-01-01

Besides fixing N2, some diazotrophic bacteria or diazotrophs, also synthesize organic acids and are able to solubilize rock phosphates, increasing the availability of P for plants. The application of these bacteria to pineapple leaf axils in combination with rock phosphate could increase N and P availability for the crop, due to the bacterial activity of biological nitrogen fixation and phosphate solubilization. The objectives of this study were: (i) to select and characterize diazotrophs abl...

Uranium-phosphate relationship in phosphated chalks of the Mons and Picardie Bassins

Energy Technology Data Exchange (ETDEWEB)

Quinif, Y; Charlet, J M; Dupuis, C; Robaszynski, F [Faculte Polytechnique de Mons (Belgium)

1981-11-30

The lithological and geochemical conditions relative to the ''Senonian'' phosphatic chalks are relatively simple in the Basins of Mons (Belgium) and of Picardy (France). Their characteristics permit us to study chiefly the uranium-phosphate relation. It appears a very good linear correlation between the phosphate and the uranium. The coefficient U/P/sub 2/O/sub 5/ remains a constant from the bottom to the top of the same section, but changes in space for synchronic formations (lateral variation of geochemical facies) and in time for two separated basins.

Uranium abundance in some sudanese phosphate ores

International Nuclear Information System (INIS)

Adam, A.A.; Eltayeb, M.A.H.

2009-01-01

This work was carried out mainly to analysis of some Sudanese phosphate ores, for their uranium abundance and total phosphorus content measured as P 2 O 5 %. For this purpose, 30 samples of two types of phosphate ore from Eastern Nuba Mountains, in Sudan namely, Kurun and Uro areas were examined. In addition, the relationship between uranium and major, and trace elements were obtained, also, the natural radioactivity of the phosphate samples was measured, in order to characterize and differentiate between the two types of phosphate ores. The uranium abundance in Uro phosphate with 20.3% P 2 O 5 is five time higher than in Kurun phosphate with 26.7% P 2 O 5 . The average of uranium content was found to be 56.6 and 310 mg/kg for Kurun and Uro phosphate ore, respectively. The main elements in Kurun and Uro phosphate ore are silicon, aluminum, and phosphorus, while the most abundant trace elements in these two ores are titanium, strontium and barium. Pearson correlation coefficient revealed that uranium in Kurun phosphate shows strong positive correlation with P 2 O 5 , and its distribution is essentially controlled by the variations of P2O5 concentration, whereas uranium in Uro phosphate shows strong positive correlation with strontium, and its distribution is controlled by the variations of Sr concentration. Uranium behaves in different ways in Kurun phosphate and in Uro phosphate. Uro phosphate shows higher concentrations of all the estimated radionuclides than Kurun phosphate. According to the obtained results, it can be concluded that Uro phosphate is consider as secondary uranium source, and is more suitable for uranium recovery, because it has high uranium abundance and low P 2 O 5 %, than Kurun phosphate. (authors) [es

Uranium from phosphate ores

International Nuclear Information System (INIS)

Hurst, F.J.

1983-01-01

The following topics are described briefly: the way phosphate fertilizers are made; how uranium is recovered in the phosphate industry; and how to detect covert uranium recovery operations in a phsophate plant

IRIS Toxicological Review of Ethyl Tertiary Butyl Ether (ETBE) (Interagency Science Consultation Draft)

Science.gov (United States)

In September 2016, EPA released the draft IRIS Toxicological Review of Ethyl Tertiary Butyl Ether (ETBE) for public comment and discussion. The draft assessment was reviewed internally by EPA and by other federal agencies and White House Offices before public release. Consistent ...

Sources and historical record of tin and butyl-tin species in a Mediterranean bay (Toulon Bay, France).

Science.gov (United States)

Pougnet, Frédérique; Schäfer, Jörg; Dutruch, Lionel; Garnier, Cédric; Tessier, Erwan; Dang, Duc Huy; Lanceleur, Laurent; Mullot, Jean-Ulrich; Lenoble, Véronique; Blanc, Gérard

2014-05-01

Concentrations of inorganic tin (Sn(inorg)), tributyltin (TBT) and its degradation products dibutyltin (DBT) and monobutyltin (MBT) were measured in surface sediments and in two cores from the Toulon Bay, hosting the major French military harbour. Anticipating planned dredging, the aim of the present work is to map and evaluate for the first time the recent and historic contamination of these sediments by inorganic and organic Sn species derived from antifouling paints used for various naval domains including military, trade, tourism and leisure. Tin and butyl-Sn concentrations in the bay varied strongly (4 orders of magnitude), depending on the site, showing maximum values near the shipyards. The concentrations of total Sn (1.3-112 μg g(-1)), TBT (product Sn(inorgBT) is by far the dominant species after 10-12 half-life periods and (c) using recent data to reliably assess former TBT contamination requires the use of a modified butyl-Sn degradation index BDI(mod). Resuspension of extremely contaminated subsurface sediments by the scheduled dredging will probably result in mobilization of important amounts of butyl-Sn species.

Structure and properties of oil palm-based nanocellulose reinforced chitosan nanocomposite for efficient synthesis of butyl butyrate.

Science.gov (United States)

Elias, Nursyafiqah; Chandren, Sheela; Attan, Nursyafreena; Mahat, Naji Arafat; Razak, Fazira Ilyana Abdul; Jamalis, Joazaizulfazli; Wahab, Roswanira Abdul

2017-11-15

In this study, nanocellulose (NC) was successfully extracted from oil palm frond leaves (OPFL) using a combination of bleaching, alkaline treatment and acid hydrolysis. X-ray diffractogram revealed the extracted NC was crystalline with a crystallinity index of 70.2%. This indicates its suitability as nano-fillers for preparing the chitosan/nanocellulose (CS-NC) supports to immobilize Candida rugosa lipase (CRL) to produce the CRL/CS-NC biocatalysts. FTIR, FESEM and TGA characterizations of the CRL/CS-NC confirm the CRLs were successfully conjugated to the CS-NC supports. The air-dried CS-NC supports gave satisfactory immobilization of the CRLs (5.2mg/g) with the resultant CRL/CS-NCs catalysed conversions of ≥80% of butyl butyrate within 6h. Time course reaction profile revealed that 76.3% butyl butyrate conversion was achieved at 4h immobilization time using 3mg/mL of CRL/CS-NCs. NMR analyses on the purified butyl butyrate confirmed that the ester was successfully synthesized. Copyright © 2017 Elsevier Ltd. All rights reserved.

{2,6-Bis[(di-tert-butyl-phosphino)-methyl]-phenyl}chloridonickel(II).

Science.gov (United States)

Boro, Brian J; Dickie, Diane A; Goldberg, Karen I; Kemp, Richard A

2008-09-20

In the title compound, [Ni(C(24)H(43)P(2))Cl], the Ni atom adopts a distorted square-planar geometry, with the P atoms of the 2,6-bis-[(di-tert-butyl-phosphino)meth-yl]phenyl ligand trans to one another. The P-Ni-P plane is twisted out of the plane of the aromatic ring by 21.97 (6)°.

Enhanced diisobutene production in the presence of methyl tertiary butyl ether

Science.gov (United States)

Smith, L.A. Jr.

1983-03-01

In the liquid phase reaction of isobutene in the presence of resin cation exchange resins with itself in a C[sub 4] hydrocarbon stream to form dimers, the formation of higher polymers, oligomers, and co-dimer by-products is suppressed by the presence of 0.0001 to 1 mole per mole of isobutene of methyl tertiary butyl ether. 1 fig.

Electrochemical Reduction of Zinc Phosphate

International Nuclear Information System (INIS)

Kim, Chang Hwan; Lee, Jung Hyun; Shin, Woon Sup

2010-01-01

We demonstrated first that the electrochemical reduction of zinc phosphate in neutral phosphate buffer is possible and potentially applicable to bio-compatible rechargeable battery. The actual redox component is Zn(s)/Zn phosphate(s) and the future research about the control of crystal formation for the better cyclability is required. In lead-acid battery, the electrochemical redox reaction of Pb (s) /PbSO 4(s) is used by reducing Pb(II) and oxidizing Pb(0) in sulfate rich solution. Since both reduced form and oxidized form are insoluble, they cannot diffuse to the opposite electrodes and react. It is a very common strategy to make a stable battery electrode that a metal element is reduced and oxidized in solution containing an abundance of anion readily precipitating with the metal ion. For the application of this strategy to construction of rechargeable battery using bio-compatible electrode materials and electrolytes, the use of phosphate ion can be considered as anion readily precipitating with metal ions. If phosphate buffer with neutral pH is used as electrolyte, the better bio-compatibility will be achieved than most of rechargeable battery using strong acid, strong base or organic solvent as electrolyte solution. There are many metal ions readily precipitating with phos-phate ion, and zinc is one of them

Radiological impact of natural radioactivity in Egyptian phosphate rocks, phosphogypsum and phosphate fertilizers

International Nuclear Information System (INIS)

El-Bahi, S.M.; Sroor, A.; Mohamed, Gehan Y.; El-Gendy, N.S.

2017-01-01

In this study, the activity concentrations of the natural radionuclides in phosphate rocks and its products were measured using a high- purity germanium detector (HPGe). The obtained activity results show remarkable wide variation in the radioactive contents for the different phosphate samples. The average activity concentration of "2"3"5U, "2"3"8U, "2"2"6Ra, "2"3"2Th and "4"0K was found as (45, 1031, 786, 85 and 765 Bq/kg) for phosphate rocks, (28, 1234, 457, 123 and 819 Bq/kg) for phosphate fertilizers, (47, 663, 550, 79 and 870 Bq/kg) for phosphogypsum and (25, 543, 409, 54 and 897 Bq/kg) for single super phosphate respectively. Based on the measured activities, the radiological parameters (activity concentration index, absorbed gamma dose rate in outdoor and indoor and the corresponding annual effective dose rates and total excess lifetime cancer risk) were estimated to assess the radiological hazards. The total excess lifetime cancer risk (ELCR) has been calculated and found to be high in all samples, which related to high radioactivity, representing radiological risk for the health of the population. - Highlights: • Level of radioactivity of phosphate rocks and by-products samples. • The radiological health hazard parameters. • Radiological risk to the health of the population. • The excess lifetime cancer risk factor.

Oxidative DNA damage in male wistar rats exposed to di-n-butyl phthalate

DEFF Research Database (Denmark)

Wellejus, A.; Dalgaard, Majken; Loft, S.

2002-01-01

Dialkyl phthalate esters are used in the plastic industry and widely distributed in the environment, Previously, it has been shown that di-n-butyl phthalate (DBP) produces testicular atrophy and liver enlargement in rodents, and the mechanisms behind this could involve reactive oxygen species (ROS...

Morphology and film formation of poly(butyl methacrylate)-polypyrrole core-shell latex particles

NARCIS (Netherlands)

Huijs, F; Lang, J

Core-shell latex particles made of a poly(butyl methacrylate) (PBMA) core and a thin polypyrrole (PPy) shell were synthesized by two-stage polymerization. In the first stage, PBMA latex particles were synthesized in a semicontinuous process by free-radical polymerization. PBMA latex particles were

5,11,17,23-Tetra-tert-butyl-25,26,27,28-tetrapropynyloxy-2,8,14,20-tetrathiacalix[4]arene

Directory of Open Access Journals (Sweden)

Xiang-Gao Meng

2009-12-01

Full Text Available The title compound [systematic name: 5,11,17,23-tetra-tert-butyl-25,26,27,28-tetrapropynyloxy-2,8,14,20-tetrathiacalix[4]arene], C52H56O4S4, is an alkylated product bearing four propyne groups at the lower rim of a 5,11,17,23-tetra-tert-butyl-tetrathiacalix[4]arene. The molecule is located on a crystallographic twofold rotation axis, running through two S atoms and perpendicular to the long axis of the molecule. The four propyne groups, located in an alternate fashion above and below the mean plane of the four S atoms, are almost parallel to the calixarene long axis. The dihedral angle between the two crystallographically independent benzene rings is 86.77 (14°. Two tert-butyl groups are disordered over two positions with site occupancies of 0.59 (2 and 0.41 (2.

Effect of tert-Butyl Functionalization on the Photoexcited Decay of a Fe(II)-N-Heterocyclic Carbene Complex

DEFF Research Database (Denmark)

Pápai, Mátyás Imre; Penfold, Thomas J.; Møller, Klaus Braagaard

2016-01-01

-vibronic quantum dynamics simulations on the Fe-N-heterocyclic carbene complex, [Fe(btbip)2]2+ (btbip = 2,6-bis(3-tert-butyl-imidazole-1-ylidene)pyridine). The results demonstrate that a relatively minor structural change compared to its parent complex, [Fe(bmip)2]2+ (bmip = 2,6-bis(3-methyl-imidazole-1-ylidene....... This occurs because the tert-butyl functionalization stabilizes the 1MC states, enabling the 1,3MLCT → 1MC population transfer to occur close to the Franck-Condon geometry, making the conversion very efficient. Subsequently, a spin cascade occurs within the MC manifold, leading to the population of triplet...

Simultaneous /sup 99m/Tc-p-butyl-IDA and 131I-rose bengal scintigraphy in neonatal jaundice

International Nuclear Information System (INIS)

Collier, B.D.; Treves, S.; Davis, M.A.; Heyman, S.; Subramanian, G.; McAfee, J.G.

1980-01-01

Eight neonates with jaundice were studied simultaneously with /sup 99m/Tc-p-butyl-IDA and 131 I-rose bengal. Due to physical decay, /sup 99m/Tc-p-butyl-IDA failed to demonstrate delayed excretion through the patent extrahepatic biliary tract in 3 of 5 patients with concomitant hepatitis; 131 I-rose bengal showed small-bowel activity in all 5. Neither agent demonstrated small-bowel activity in 3 neonates with extrahepatic biliary atresia. Based on this clinical trial, 131 I-rose bengal remains the radiopharmaceutical of choice for distinguishing between hepatitis and biliary atresia in these patients

Calcium phosphates: what is the evidence?

Science.gov (United States)

Larsson, Sune

2010-03-01

A number of different calcium phosphate compounds such as calcium phosphate cements and solid beta-tricalcium phosphate products have been introduced during the last decade. The chemical composition mimics the mineral phase of bone and as a result of this likeness, the materials seem to be remodeled as for normal bone through a cell-mediated process that involves osteoclastic activity. This is a major difference when compared with, for instance, calcium sulphate compounds that after implantation dissolve irrespective of the new bone formation rate. Calcium phosphates are highly biocompatible and in addition, they act as synthetic osteoconductive scaffolds after implantation in bone. When placed adjacent to bone, osteoid is formed directly on the surface of the calcium phosphate with no soft tissue interposed. Remodeling is slow and incomplete, but by adding more and larger pores, like in ultraporous beta-tricalcium phosphate, complete or nearly complete resorption can be achieved. The indications explored so far include filling of metaphyseal fracture voids or bone cysts, a volume expander in conjunction with inductive products, and as a carrier for various growth factors and antibiotics. Calcium phosphate compounds such as calcium phosphate cement and beta-tricalcium phosphate will most certainly be part of the future armamentarium when dealing with fracture treatment. It is reasonable to believe that we have so far only seen the beginning when it comes to clinical applications.

Exchange reactions between a molten salt and a solution of tri-butyl phosphate in a liquid silicone; Reactions d'echange entre un sel fondu et une solution de phosphate de tributyle dans un silicone liquide

Energy Technology Data Exchange (ETDEWEB)

Hertzog, D [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

Present interest centred around molten salts can be explained by their possible use in the field of nuclear energy, in particular as a support for fuels and also as reprocessing agents. It seemed of interest to consider the molten salt as a solvent and to study partition phenomena with a second phase stable at high temperatures. The salt chosen is a ternary eutectic of alkali nitrates and the second phase is a solution of tri-butyl phosphate in a liquid silicone. The working temperature is fixed at 150 deg. C. We have studied first of all the stability of the two phases and their mutual solubilities at this temperature. It has been shown that the two solvents are immiscible and stable. We have also described the extraction by the silicone solution of various products in solution in the salt phase, and have determined the partition coefficients and the formulae of the extracted molecules. It has been possible to calculate the partition coefficients of the following ions extracted as nitrates: Li{sup +}, Na{sup +}, K{sup +}, Sr{sup 2+}, Ca{sup 2+}, Ba{sup 2+}, Hg{sup 2+} whose partition coefficients are very low: Mg{sup 2+}, Ni{sup 2+}, Co{sup 2+}, Zn{sup 2+} whose extraction yields are greater than 50 per cent; finally Ce{sup 3+}, La{sup 3+}, UO{sub 2}{sup 2+}, highly extracted. Also the following anions have been extracted in the form of alkali salts: F{sup -}, Cl{sup -}, Br{sup -}, I{sup -}, IO{sub 3}{sup -}, CN{sup -}, SO{sub 4}{sup -}, C{sub 2}O{sub 4}{sup -}, NO{sub 2}{sup -}. Amongst these, only the halogens have non-negligible partition coefficients. In certain particular cases we have been able to study the influence of complex formation on the extraction phenomena. Two applications are described: - The separation of two products by complex formation and extraction (separation of magnesium from cobalt, nickel and zinc); - The calculation of the equilibrium constant of a complex by measurement of the variation in the partition coefficient of the ion complexed

Ureteric Embolization for Lower Urinary Tract Fistulae: Use of Two Amplatzer Vascular Plugs and N-Butyl Cyanoacrylate Employing the 'Sandwich' Technique

Energy Technology Data Exchange (ETDEWEB)

Saad, Wael E. A., E-mail: ws6r@virginia.edu; Kalagher, S.; Turba, U. C.; Sabri, S. S.; Park, A.-W.; Stone, J.; Angle, J. F.; Matsumoto, A. H. [University of Virginia Health System, Department of Radiology and Medical Imaging, Division of Vascular Interventional Radiology (United States)

2013-08-01

PurposeThis study describes and evaluated the effectiveness of occluding distal ureters in the clinical setting of urinary vaginal (vesicovaginal or enterovesicovaginal) fistulae utilizing a new technique which combines Amplatzer vascular plugs and N-butyl cyanoacrylate.MaterialsThis is a retrospective study (January 2007-December 2010) of patients with urinary-vaginal fistulae undergoing distal ureter embolization utilizing an Amplatzer- N-butyl cyanoacrylate-Amplatzer sandwich technique. An 8-12-mm type-I or type-II Amplatzer vascular plug was delivered using the sheath and deployed in the ureter distal to the pelvic brim. Instillation of 0.8-1.5 cc of N-butyl cyanoacrylate into ureter proximal to the Amplatzer plug was performed. This was followed by another set of 8-12-mm type-I or type-II Amplatzer vascular plugs in a technique referred to as the 'sandwich technique.'ResultsFive ureters in three patients were occluded utilizing the above-described technique during the 4-year study period. Mean maximum size Amplatzer used per ureter was 10.8 mm (range, 8-12). One ureter required three Amplatzer plugs and the rest required two. Two patients (3 ureters) were clinically successful with complete resolution of symptoms in 36-48 h. The third patient (2 ureters) was partly successful and required a second Amplatzer- N-butyl cyanoacrylate sandwich technique embolization. The mean clinical follow-up was 11.3 months (range, 1.7-29.2).ConclusionsThe Amplatzer- N-butyl cyanoacrylate-Amplatzer sandwich technique for occluding the distal ureter is safe and effective with a quick (probably due to the N-butyl cyanoacrylate) and durable (probably due to the Amplatzer plugs) clinical response.

Characterization of Z-RAFT star polymerization of butyl acrylate by size-exclusion chromatography

NARCIS (Netherlands)

Boschmann, D.; Edam, R.; Schoenmakers, P.J.; Vana, P.

2009-01-01

Z-RAFT star polymerization of butyl acrylate using multifunctional trithiocarbonate-type RAFT agents carrying methyl propionate as the leaving group were used to form star polymers having 3, 4, and 6 arms. The polymerizations showed well controlled behavior up to high monomer conversions. By using a

[Photometric determination of butyl "aeroflot" flotation agent (sodium dibutyl dithiophosphate) in the air of work zone and skin washings].

Science.gov (United States)

Dorogova, V B; Kucheriavykh, E I; Sokolova, T V

1989-01-01

Photometric procedure of butyl "aeroflot" identification in the work zone air and in wash-out from workers' integument was developed, The procedure was based on the formation of yellow- and orange-dyed copper dibutyl dithiophosphate under butyl "aeroflot" interaction with copper sulphate with the subsequent photometry of dyed solutions for the wavelength of 420 nm in the 10-mm cell. Buffer solution with pH-9.2 was used as an absorbing solution for the workplace air sampling and integument wash-out.

A study of butyl acetate synthesis. 4-reaction kinetics

OpenAIRE

Álvaro Orjuela Londoño; Fernando Leiva Lenis; Luis Alejandro Boyacá Mendivelso; Gerardo Rodríguez Niño; Luis María Carballo Suárez

2006-01-01

This work was aimed at studying liquid-phase acetic acid and butyl alcohol esterification reaction (P atm =0.76 Bar),using an ion exchange resin (Lewatit K-2431) as catalyst. The effect of the absence of internal and external mass transport on catalyst particles was established in the research conditions used here. A set of assays to determine the effect of catalyst load (0.5%, 1%, 2% w/w) temperature (73°C, 80°C, 87°C) and molar ratio (1:2, 1:1, 2:1 acid/alcohol) on reaction rate was carrie...

Phosphate additives in food--a health risk.

Science.gov (United States)

Ritz, Eberhard; Hahn, Kai; Ketteler, Markus; Kuhlmann, Martin K; Mann, Johannes

2012-01-01

Hyperphosphatemia has been identified in the past decade as a strong predictor of mortality in advanced chronic kidney disease (CKD). For example, a study of patients in stage CKD 5 (with an annual mortality of about 20%) revealed that 12% of all deaths in this group were attributable to an elevated serum phosphate concentration. Recently, a high-normal serum phosphate concentration has also been found to be an independent predictor of cardiovascular events and mortality in the general population. Therefore, phosphate additives in food are a matter of concern, and their potential impact on health may well have been underappreciated. We reviewed pertinent literature retrieved by a selective search of the PubMed and EU databases (www.zusatzstoffe-online.de, www.codexalimentarius.de), with the search terms "phosphate additives" and "hyperphosphatemia." There is no need to lower the content of natural phosphate, i.e. organic esters, in food, because this type of phosphate is incompletely absorbed; restricting its intake might even lead to protein malnutrition. On the other hand, inorganic phosphate in food additives is effectively absorbed and can measurably elevate the serum phosphate concentration in patients with advanced CKD. Foods with added phosphate tend to be eaten by persons at the lower end of the socioeconomic scale, who consume more processed and "fast" food. The main pathophysiological effect of phosphate is vascular damage, e.g. endothelial dysfunction and vascular calcification. Aside from the quality of phosphate in the diet (which also requires attention), the quantity of phosphate consumed by patients with advanced renal failure should not exceed 1000 mg per day, according to the guidelines. Prospective controlled trials are currently unavailable. In view of the high prevalence of CKD and the potential harm caused by phosphate additives to food, the public should be informed that added phosphate is damaging to health. Furthermore, calls for labeling

Phosphate analysis of natural sausage casings preserved in brines with phosphate additives as inactivating agent - Method validation.

Science.gov (United States)

Wijnker, J J; Tjeerdsma-van Bokhoven, J L M; Veldhuizen, E J A

2009-01-01

Certain phosphates have been identified as suitable additives for the improvement of the microbial and mechanical properties of processed natural sausage casings. When mixed with NaCl (sodium chloride) and used under specific treatment and storage conditions, these phosphates are found to prevent the spread of foot-and-mouth disease and classical swine fever via treated casings. The commercially available Quantichrom™ phosphate assay kit has been evaluated as to whether it can serve as a reliable and low-tech method for routine analysis of casings treated with phosphate. The outcome of this study indicates that this particular assay kit has sufficient sensitivity to qualitatively determine the presence of phosphate in treated casings without interference of naturally occurring phosphate in salt used for brines in which casings are preserved.

Multiple cutaneous leiomyomas: Pain relief with pulsed hysocine butyl bromide

Directory of Open Access Journals (Sweden)

Kaliyadan Feroze

2009-01-01

Full Text Available A 35-year-old male patient presented to our outpatient department, complaining of multiple, raised skin lesions on the forehead and back, associated with intermittent pain, especially on exposure to cold. A diagnosis of cutaneous leiomyoma (type 2 segmental was made, which was confirmed by skin biopsy. The patient was started on a trial of pulsed Hyoscine Butyl bromide tablets, following which the patient had significant relief from pain associated with the lesions.

Characterization of a calcium phosphate cement based on alpha-tricalcium phosphate obtained by wet precipitation process

International Nuclear Information System (INIS)

Thurmer, M.B.; Diehl, C.E.; Vieira, R.S.; Coelho, W.T.G.; Santos, L.A.

2012-01-01

There are several systems of calcium phosphate cements being studied. Those based on alpha-tricalcium phosphate are of particular interest. After setting they produce calcium deficient hydroxyapatite similar to bone like hydroxyapatite. This work aims to obtain alpha-tricalcium phosphate powders by the wet precipitation process, using calcium nitrate and phosphoric acid as reagents. This powder was characterized by infrared spectroscopy, X-ray diffraction and particle size distribution. In order to prepare the calcium phosphate cement, the powder was mixed with an accelerator in an aqueous solution. The mechanical properties of the cement were assessed and it was evaluated by means of apparent density, X-ray diffraction and scanning electron microscopy. The described method produced crystalline alpha-tricalcium phosphate as the major phase. The calcium phosphate cement showed high values of compression strength (50 MPa). The soaking of the cement in a simulated body fluid (SBF) formed a layer of hydroxyapatite like crystals in the surface of the samples. (author)

Phosphate solubilization and multiple plant growth promoting ...

African Journals Online (AJOL)

Phosphate solubilizing efficiencies of the strains were analyzed using different insoluble phosphorus sources and the results show that most isolates released a substantial amount of soluble phosphate from tricalcium phosphate, rock phosphate and bone meal. Screening for multiple plant growth promoting attributes ...

Application of butyl alcohol bacteria for the fermentation of nonnutritive raw materials

Energy Technology Data Exchange (ETDEWEB)

Nakhamanovich, B M; Senkevich, V V; Yarovenko, V L

1961-01-01

Materials like corncobs after hydrolysis can be economically fermented by using bacteria which support a butyl alcohol-acetone fermentation. Best results are obtained if (NH/sub 4/)/sub 2/SO/sub 4/ and superphosphate are added to the fermentation liquor. Analyses are presnted of the hydrolzates (alcohols, formic acid, 2-furaldehyde, and reducing sugars) and of the final products.

Biphasic kinetic investigations on the evaluation of non-salt forming reductants for Pu(IV) stripping from tributyl phosphate and N,N-dihexyl octanamide solutions in n-dodecane

International Nuclear Information System (INIS)

Prabhu, D.R.; Neelam Kumari; Kanekar, A.S.; Pathak, P.N.

2013-01-01

The relative stability of different oxidation states of actinide elements is influenced by the nature of complexes formed and redox equilibria in aqueous/non-aqueous solutions. The reduction/stripping studies on Pu(IV) ions from loaded organic phases of 1.1 M tributyl phosphate and of 1.1 M N,N-dihexyl octanamide in n-dodecane were studied using organic soluble tert-butyl hydroquinone (TBH) and aqueous soluble reductants like acetaldoxime (AX) and hydroxyurea (HU). These studies were carried out as a function of reductant and nitric acid concentration (0.5-4 M HNO 3 ) and of time. The changes in Pu oxidation states were followed by spectrophotometry for TBH and by distribution ratio values for AX and HU as reductants. Spectrophotometric investigations using TBH as reductant showed that it was desirable to strip Pu(III) formed after reduction of Pu(IV) in the organic phase, which may otherwise be reconverted to extractable Pu(IV) by in situ generated HNO 2 from oxidative degradation of TBH to tert-butyl quinone. Similarly, the biphasic reduction/stripping of Pu(IV) using AX and HU as reductant rate was affected adversely with increased aqueous phase acidity. This data will help in the accurate simulation of Pu separation processes using these reductants in mixer-settlers/pulsed columns or centrifugal contactors. (author)

IRIS Toxicological Review of Ethylene Glycol Mono-Butyl Ether (Egbe) (Interagency Science Discussion Draft)

Science.gov (United States)

EPA released the draft report, Toxicological Review for Ethylene Glycol Mono-Butyl Ether , that was distributed to Federal agencies and White House Offices for comment during the Science Discussion step of the IRIS Assessment Development Process. Comments received from ot...

DERMAL, ORAL, AND INHALATION PHARMACOKINETICS OF METHYL TERTIARY BUTYL ETHER (MTBE) IN HUMAN VOLUNTEERS

Science.gov (United States)

Methyl tertiary butyl ether (MTBE), a gasoline additive, used to increase octane and reduce carbon monoxide emissions and ozone precursors has contaminated drinking water leading to exposure by oral, inhalation, and dermal routes. To determine its dermal, oral, and inhalation ki...

Iodine catalyzed and tertiary butyl ammonium bromide promoted p reparation of b enzoxazaphosphininyl phenylboronates

Directory of Open Access Journals (Sweden)

K. R. Kishore K. Reddy,

2009-05-01

Full Text Available Benzoxazaphosphininyl Phenylboronates were prepared by O-Phosphorylation of potassium salt ofphenylboronic acid with cyclic phosphoromonochloridates in the presence of stoichiometric amount of Iodineand catalytic amount of tertiary butyl ammonium bromide at 50-60 °C in dry toluene.

Evaluation of intestinal phosphate binding to improve the safety profile of oral sodium phosphate bowel cleansing.

Directory of Open Access Journals (Sweden)

Stef Robijn

Full Text Available Prior to colonoscopy, bowel cleansing is performed for which frequently oral sodium phosphate (OSP is used. OSP results in significant hyperphosphatemia and cases of acute kidney injury (AKI referred to as acute phosphate nephropathy (APN; characterized by nephrocalcinosis are reported after OSP use, which led to a US-FDA warning. To improve the safety profile of OSP, it was evaluated whether the side-effects of OSP could be prevented with intestinal phosphate binders. Hereto a Wistar rat model of APN was developed. OSP administration (2 times 1.2 g phosphate by gavage with a 12h time interval induced bowel cleansing (severe diarrhea and significant hyperphosphatemia (21.79 ± 5.07 mg/dl 6h after the second OSP dose versus 8.44 ± 0.97 mg/dl at baseline. Concomitantly, serum PTH levels increased fivefold and FGF-23 levels showed a threefold increase, while serum calcium levels significantly decreased from 11.29 ± 0.53 mg/dl at baseline to 8.68 ± 0.79 mg/dl after OSP. OSP administration induced weaker NaPi-2a staining along the apical proximal tubular membrane. APN was induced: serum creatinine increased (1.5 times baseline and nephrocalcinosis developed (increased renal calcium and phosphate content and calcium phosphate deposits on Von Kossa stained kidney sections. Intestinal phosphate binding (lanthanum carbonate or aluminum hydroxide was not able to attenuate the OSP induced side-effects. In conclusion, a clinically relevant rat model of APN was developed. Animals showed increased serum phosphate levels similar to those reported in humans and developed APN. No evidence was found for an improved safety profile of OSP by using intestinal phosphate binders.

Simultaneous determination of triacetin, acetic ether, butyl acetate and amorolfine hydrochloride in amorolfine liniment by HPLC.

Science.gov (United States)

Gao, Yuan; Li, Li; Zhang, Jianjun; Shu, Wenjuan; Gao, Liqiong

2012-04-01

A simple, rapid, specific and precise reversed-phase high-performance liquid chromatographic method was developed for simultaneous estimation of triacetin, acetic ether, butyl acetate and amorolfine in marketed pharmaceutical liniment. Chromatographic separation was performed on a Shimadzu VP-ODS C(18) column using the mixture of citric acid-hydrochloric acid-sodium hydrate buffer (pH 3.0), acetonitrile and methanol (32:30:38) as the mobile phase at a flow rate of 1.0 mL/min with UV-detection at 215 nm. The method separated the four components simultaneously in less than 10 min. The validation of the method was performed with respect to specificity, linearity, accuracy, and precision. The calibration curves were linear in the range of 35.1-81.9 μ/mL for triacetin, 431.1-1005.9 μ/mL for acetic ether, 167.0-389.7 μ/mL for butyl acetate and 151.0-352.3 μ/mL for amorolfine. The mean 100% spiked recovery for triacetin, acetic ether, butyl acetate and amorolfine is 99.43 ± 0.42, 101.5 ± 1.09, 101.4 ± 1.02 and 100.8 ± 0.69, respectively. The intra-day and inter-day relative standard deviation values were liniment.

Phosphate and phosphate fertilizer sector: structure and future prospects. [Uranium recovery

Energy Technology Data Exchange (ETDEWEB)

Zenaidi, B

1981-12-01

A statement of the past evolution of this sector's structure is given. Various prospective studies which have been made are reviewed and lead to the precision of the phosphate requirement in the year 2000 which is between 200 and 250 Mt. Only a small section p. 696-697 is devoted to recovery of uranium contained in phosphate and prospects in this field are given.

Bibliographic report on the synthesis, the chemical and physical properties and the applications of the TBP phosphate

International Nuclear Information System (INIS)

Azzouz, A.; Attou, M.

1985-02-01

This work consists of a bibliographic synthesis concerning the tri-n-butylphosphate (TBP) technology. It gathers briefly in 56 references on a table, the multiple applications of TBP such as extraction, spectroscopy and various other uses. Then, it deals with chemical instability different causes of this substance as well as its physical and chemical properties. In this way, for instance, the thermal degradation occurs well before the TBP boiling point. It comes out of this, several decomposition products such as the mono-n-butyl-phosphate (MBP), the di-n-butylphosphate (DBP) and some olefins. The acids and some impurities are known to have effects on TBP degradation. Later on, some processes of the TBP synthesis and their principles are stated. In the major cases, the POCl 3 process seems to be the best way, probably because of convenient efficiencies and moderate conditions of its making. Some purification processes according to the TBP use are also invoqued. In this case as well, Alcock et al. method is often stated in the literature. Moreover, five analysis methods corresponding to the most common situations are described

Better prospects for phosphate production

Energy Technology Data Exchange (ETDEWEB)

1980-06-01

The extraction of uranium as a by product of phosphate production is discussed. Techniques being commercially developed are described. The trend towards the wet process, in which sulphuric acid is used to dissolve the phosphate, producing phosphoric acid, is also the preferred method for uranium recovery. Recovery from a wet process phosphoric acid stream, integrated with phosphate fertilizer manufacture, is becoming increasingly commercially viable for the production of yellow-cake.

Preparation and Properties of Triethoxyvinylsilane-Modified Styrene - Butyl Acrylate Emulsion Copolymers

OpenAIRE

NAGHASH, Hamid Javaherian; KARIMZADEH, Akram; MOMENI, Ahmad Reza; MASSAH, Ahmad Reza; ALIAN, Hamid

2014-01-01

The copolymers of triethoxyvinylsilane (TEVS) with styrene (St), butyl acrylate (BA), and methacrylic acid (MAA) were prepared by emulsion polymerization. The copolymerization was carried out by using auxiliary agents at 90 °C in the presence of potassium peroxodisulfate (KPS) as the initiator. Nonylphenol ethylene oxide -- 40 units (NP-40) and sodium lauryl sulfoacetate (SLSA) were used as nonionic and anionic emulsifiers, respectively. The resulting copolymers were characterized b...

The Oxygen Isotopic Composition of Phosphate: A Tracer for Phosphate Sources and Cycling

Energy Technology Data Exchange (ETDEWEB)

Mclaughlin, K. [Southern California Coastal Water Research Project, Costa Mesa, University of California, CA (United States); Young, M. B.; Paytan, A.; Kendall, C. [U.S. Geological Survey, University of California, CA (United States)

2013-05-15

Phosphorus (P) is a limiting macro-nutrient for primary productivity and anthropogenic P-loading to aquatic ecosystems is one of the leading causes of eutrophication in many ecosystems throughout the world. Because P has only one stable isotope, traditional isotope techniques are not possible for tracing sources and cycling of P in aquatic systems. However, much of the P in nature is bonded to four oxygen (O) atoms as orthophosphate (PO{sub 4}{sup 3-}). The P-O bonds in orthophosphate are strongly resistant to inorganic hydrolysis and do not exchange oxygen with water without biological mediation (enzyme-mediated recycling). Thus, the oxygen isotopic composition of dissolved inorganic phosphate ({delta}{sup 18}O{sub p}) may be used as a tracer for phosphate sources and cycling in aquatic ecosystems. Recently, several studies have been conducted utilizing {delta}{sup 18}O{sub p} as a tracer for phosphate sources and cycling in various aquatic environments. Specifically, work to date indicates that {delta}{sup 18}O{sub p} is useful for determining sources of phosphate to aquatic systems if these sources have unique isotopic signatures and phosphate cycling within the system is limited compared to input fluxes. In addition, because various processes imprint specific fractionation effects, the {delta}{sup 18}O{sub p} tracer can be utilized to determine the degree of phosphorous cycling and processing through the biomass. This chapter reviews several of these studies and discusses the potential to utilize the {delta}{sup 18}O{sub p} of phosphate in rivers and streams. (author)

The 1:1 co-crystal of triphenyl(2,3,5,6-tetrafluorobenzylphosphonium bromide and 1,1,2,2-tetrafluoro-1,2-diiodoethane

Directory of Open Access Journals (Sweden)

Gabriella Cavallo

2014-01-01

Full Text Available The title compound, C25H18F4P+·Br−·C2F4I2, is a 1:1 co-crystal of triphenyl(2,3,5,6-tetrafluorobenzylphosphonium (TTPB bromide and 1,1,2,2-tetrafluoro-1,2-diiodoethane (TFDIE. The crystal structure consists of a framework of TTPB cations held together by C—H...Br interactions. In this framework, infinite channels along [100] are filled by TFDIE molecules held together in infinite ribbons by short F...F [2.863 (2–2.901 (2Å] interactions. The structure contains halogen bonds (XB and hydrogen bonds (HB in the bromide coordination sphere. TFDIE functions as a monodentate XB donor as only one I atom is linked to the Br− anion and forms a short and directional interaction [I...Br− 3.1798 (7 Å and C—I...Br− 177.76 (5°]. The coordination sphere of the bromide anion is completed by two short HBs of about 2.8 Å (for H...Br with the acidic methylene H atoms and two longer HBs of about 3.0 Å with H atoms of the phenyl rings. Surprisingly neither the second iodine atom of TFDIE nor the H atom on the tetrafluorophenyl group make any short contacts.

DERMAL, ORAL AND INHALATION PHARMACOKINETICS OF METHYL TERTIARY-BUTYL ETHER (MTBE) IN HUMAN VOLUNTEERS

Science.gov (United States)

Methyl tertiary butyl ether (MTBE), a gasoline additive used to increase octane and reduce carbon monoxide emissions and ozone precursors, has contaminated drinking water and can lead to exposure by oral, inhalation, and dermal routes. To determine its dermal, oral, and inhal...

Occurrence and functioning of phosphate solubilizing ...

African Journals Online (AJOL)

Occurrence and functioning of phosphate solubilizing microorganisms from oil palm tree ( Elaeis guineensis ) rhizosphere in Cameroon. ... While the use of soluble mineral phosphate fertilizers is the obvious best means to combat phosphate ... in order to improve agricultural production, using low inputs technology. Isolates ...

A new efficient synthesis of isothiocyanates from amines using di-tert-butyl dicarbonate

DEFF Research Database (Denmark)

Munch, Henrik; Hansen, Jon S.; Pittelkow, Michael

2008-01-01

Alkyl and aryl amines are converted smoothly to the corresponding isothiocyanates via the dithiocarbamates in good to excellent yields using di-tert-butyl dicarbonate (Boc(2)O) and 1-3 mol% of DMAP or DABCO as catalyst. As most of the byproducts are volatile, the work-up involves simple evaporation...

Glycerol tertiary butyl ethers via etherification of glycerol with isobutene

Energy Technology Data Exchange (ETDEWEB)

Behr, A. [Dortmund Univ. (Germany). Chair of Chemical Process Development/Technical Chemistry A

2007-07-01

Glycerol and isobutene can react to a mixture of glycerol tertiary butyl ethers (GTBE) which can be used as additives for gasoline, diesel or biodiesel. This reaction was investigated in lab scale yielding a proposal for a process flow diagram containing reaction, extraction, flash and rectification units. This process has the advantages that only the suitable higher ethers are formed and that both glycerol and isobutene are fully converted. The homogeneous acid catalyst is low-priced and can be completely recycled. (orig.)

PHOSPHATE CRYSTALLURIA IN VARIOUS FORMS OF UROLITHIASIS AND POSSIBILITIES OF ITS PROGNOSTICATION IN PATIENTS WITH PHOSPHATE STONES

Directory of Open Access Journals (Sweden)

O. V. Konstantinova

2017-01-01

Full Text Available Purpose. Definition of types of crystalluria in various forms of urolithiasis and biochemical signs of phosphate crystals in the urine, while phosphate urolithiasis (infectious origin.Patients and methods. The study involved 144 patients with recurrent urolithiasis — 75 women and 69 men. Of these, 46 — diagnosed calculi with uric acid, 44 — calcium oxalate or mixed with a prevalence of calcium oxalate, in 54 — phosphate rocks (carbonate-apatite and/or struvite. The age of patients ranged from 21 to 74 years. 93 people have been under long-term, within 2–15 years, outpatient observation. The examination included the collection of anamnesis, general and microbiological analysis of urine, biochemical blood serum and urine on 10 indicators, reflecting renal function, state of the protein, water and electrolyte metabolism, uric acid metabolism, the chemical composition of the stone analysis.Results. It was found that in patients with calcium oxalate stones phosphaturia has been diagnosed in 2% of cases. And, along with calcium phosphate crystals they had oxalate crystals. In patients with phosphate urolithiasis phosphaturia observed in 96% of patients, in two patients (4% they determined except phosphates also oxalate salt in urine sediment. Patients with phosphate urolithiasis at occurrence of phosphate crystalluria have metabolic state changes: increased serum uric acid concentration from 0.322 ± 0.009 to 0.367 ± 0.018 mmol/l daily renal excretion of inorganic phosphate 23.94 ± 2.93 mmol/day to 32.12 ± 4.39 mmol/day, and reduced total calcium content in urine 6.61 ± 0.94 mmol/day to 3.37 ± 0.89 mmol/day. The results led to the following conclusion.Conclusion. Biochemical signs of occurrence of phosphate crystalluria in patients with stones of infectious origin can be: the approaching level of excretion in the urine of inorganic phosphates to 32,12 ± 4,39 mmol/day, serum uric acid concentration to 0,367 ± 0,018 mmol/l, and the

Bio-treatment of phosphate from synthetic wastewater using ...

African Journals Online (AJOL)

In this study, the efficient phosphate utilizing isolates were used to remove phosphate from synthetic phosphate wastewater was tested using batch scale process. Hence the objective of the present study was to examine the efficiency of bacterial species individually for the removal of phosphate from synthetic phosphate ...

n-Alkane assimilation and tert-butyl alcohol (TBA) oxidation capacity in Mycobacterium austroafricanum strains.

Science.gov (United States)

Lopes Ferreira, Nicolas; Mathis, Hugues; Labbé, Diane; Monot, Frédéric; Greer, Charles W; Fayolle-Guichard, Françoise

2007-06-01

Mycobacterium austroafricanum IFP 2012, which grows on methyl tert-butyl ether (MTBE) and on tert-butyl alcohol (TBA), the main intermediate of MTBE degradation, also grows on a broad range of n-alkanes (C2 to C16). A single alkB gene copy, encoding a non-heme alkane monooxygenase, was partially amplified from the genome of this bacterium. Its expression was induced after growth on n-propane, n-hexane, n-hexadecane and on TBA but not after growth on LB. The capacity of other fast-growing mycobacteria to grow on n-alkanes (C1 to C16) and to degrade TBA after growth on n-alkanes was compared to that of M. austroafricanum IFP 2012. We studied M. austroafricanum IFP 2012 and IFP 2015 able to grow on MTBE, M. austroafricanum IFP 2173 able to grow on isooctane, Mycobacterium sp. IFP 2009 able to grow on ethyl tert-butyl ether (ETBE), M. vaccae JOB5 (M. austroaafricanum ATCC 29678) able to degrade MTBE and TBA and M. smegmatis mc2 155 with no known degradation capacity towards fuel oxygenates. The M. austroafricanum strains grew on a broad range of n-alkanes and three were able to degrade TBA after growth on propane, hexane and hexadecane. An alkB gene was partially amplified from the genome of all mycobacteria and a sequence comparison demonstrated a close relationship among the M. austroafricanum strains. This is the first report suggesting the involvement of an alkane hydroxylase in TBA oxidation, a key step during MTBE metabolism.

Carcinogenicity study on butylated hydroxytoluene (BHT) in Wistar rats exposed in utero

DEFF Research Database (Denmark)

Olsen, P.; Meyer, Otto A.; Bille, N.

1986-01-01

Groups of 60, 40, 40 and 60 F0 Wistar rats of each sex were fed a semi-synthetic diet containing butylated hydroxytoluene (BHT) in concentrations to provide intakes of 0, 25, 100 or 500 mg/kg body weight/day, respectively. The F0 rats were mated and groups of 100, 80, 80 or 100 F1 rats of each sex...

(R-N-{2-tert-Butyl-2-[(R-tert-butylsulfonamido]ethylidene}-tert-butanesulfonamide

Directory of Open Access Journals (Sweden)

Cong-Bin Fan

2008-10-01

Full Text Available The title compound, C14H30N2O2S2, is the product of the monoaddition reaction of tert-butyl magnesium chloride with bis-[(R-N-tert-butanesulfinyl]ethanediimine. There are two almost identical molecules in the asymmetric unit, the molecular conformation of which is stabilized by an intramolecular N—H...N hydrogen bond.

Infrared-spectroscopy analysis of zinc phosphate and nickel and manganese modified zinc phosphate coatings on electrogalvanized steel

International Nuclear Information System (INIS)

Fernandes, Kirlene Salgado; Alvarenga, Evandro de Azevedo; Lins, Vanessa de Freitas Cunha

2011-01-01

Hopeite-type phosphate coatings in which zinc is partially replaced by other metals like manganese and nickel are of great interest for the automotive and home appliance industries. Such industries use phosphate conversion coatings on galvanized steels in association with cataphoretic electro painting. Zinc phosphates modified with manganese and nickel are isomorphic with the hopeite, and the phase identification using X-ray diffraction is difficult. In this paper, the phosphate coatings are identified using the Fourier transform infrared spectroscopy (FTIR). (author)

Application of Calcium Phosphate Materials in Dentistry

Directory of Open Access Journals (Sweden)

Jabr S. Al-Sanabani

2013-01-01

Full Text Available Calcium phosphate materials are similar to bone in composition and in having bioactive and osteoconductive properties. Calcium phosphate materials in different forms, as cements, composites, and coatings, are used in many medical and dental applications. This paper reviews the applications of these materials in dentistry. It presents a brief history, dental applications, and methods for improving their mechanical properties. Notable research is highlighted regarding (1 application of calcium phosphate into various fields in dentistry; (2 improving mechanical properties of calcium phosphate; (3 biomimetic process and functionally graded materials. This paper deals with most common types of the calcium phosphate materials such as hydroxyapatite and tricalcium phosphate which are currently used in dental and medical fields.

Emulsion (Co)polymerization of styrene and butyl acrylate monitored by On-line Raman Spectroscopy

NARCIS (Netherlands)

van den Brink, H.J.T.; Pepers, M.L.H.; Herk, van A.M.; German, A.L.

2000-01-01

The homo- and copolymerizations of styrene and n-butyl acrylate were studied by on-line in-situ Raman spectroscopy.Results from the solution (homo)polymerizations proved to be very useful in the quantification of the Raman data from the emulsion homopolymerization. From the homopolymerization data

Continuous ARGET ATPR of methyl methacrylate and butyl acrylate in a stirred tank reactor

NARCIS (Netherlands)

Chan, N.; Meuldijk, J.; Cunningham, M.F.; Hutchinson, R.A.

2013-01-01

ARGET ATRP (activator regenerated by electron transfer atom transfer radical polymerization) of butyl acrylate (BA) and methyl methacrylate (MMA) was successfully adapted from a batch process to a continuous stirred tank reactor (CSTR) with 50 ppm copper. A series of batch polymerizations were first

Time-Resolved WAXD and SAXS Investigations on Butyl Branched Alkane at Elevated Pressures

NARCIS (Netherlands)

Rastogi, A.; Hobbs, J.K.; Rastogi, S.

2002-01-01

The crystallization behavior and the morphological aspect of the butyl branched alkane C96H193CH(C4H9)C94H189 have been investigated using time-resolved wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) at atmospheric and elevated pressures. The solution crystallized sample

Comparative stability, toxicity and anti-leishmanial activity of triphenyl antimony(v) and bismuth(v) α-hydroxy carboxylato complexes.

Science.gov (United States)

Duffin, Rebekah N; Blair, Victoria L; Kedzierski, Lukasz; Andrews, Philip C

2018-01-15

A series of triphenyl Sb(v) and Bi(v) α-hydroxy carboxylato complexes of the general formula [MPh 3 (O 2 CROH) 2 ] and [MPh 3 (O 2 CRO)] have been successfully synthesised and characterised, and subsequently assayed for their comparative activity towards Leishmania parasites and human fibroblast cells. Four complexes are novel; [SbPh 3 Gly], [BiPh 3 (GlyH) 2 ], [SbPh 3 (R-ManH) 2 ] and [SbPh 3 (S-ManH) 2 ], and have been structurally characterised through X-ray diffraction. These were combined in the study with the known complexes; ([SbPh 3 (R-Man)], [SbPh 3 (S-Man)], [BiPh 3 (R-ManH) 2 ], [BiPh 3 (R-ManH) 2 ], [SbPh 3 (BenzH) 2 ], [BiPh 3 (BenzH) 2 ], for which the crystal structures of [BiPh 3 (S-ManH) 2 ] and [BiPh 3 (R-Man) 2 ] have now been authenticated (GlyH 2 = glycolic acid, R/S-ManH 2 = mandelic acid, BenzH 2 = benzilic acid). The complexes adopt a typical bipyramidal 7-coordinate geometry with the phenyl rings occupying the equatorial plane, and the ligands on the axial. In contrast to previous studies the Bi(v) compounds show a relatively high degree of stability in DMEM culture media. Promastigote and human fibroblast cell assays showed the Bi(v) analogues to be non-selectively toxic with a respective IC 50 range of 3.58-6.33 μM and 5.83-7.01 μM. In contrast, the Sb(v) analogues provided much greater selectivity (promastigotes 12.5-20.7; fibroblasts 72.8-≥100 μM). Assessment of the Sb(v) complexes against amastigotes at 10 μM showed them to be effective with % infection values ranging from 9.5 ± 0.5-30 ± 1.3.

Phosphate acquisition efficiency and phosphate starvation tolerance ...

Indian Academy of Sciences (India)

3Department of Genetics and Plant Breeding, College of Agriculture, Lembucherra, Tripura 799 ... vated in soil like red and lateritic or acid, with low soluble phosphate content. ..... activation of genes involved in the adaptation of Arabidopsis to.

Synthesis of 2,6-diisopropyl-phenylcarbamoylmethyl-iminodiacetic acid (DISIDA) and 4-n-p-butyl-phenylcarbamoylmethyl-iminodiacetic acid (BUTYL-IDA). Preparation of lyophilized kit to be used as 99(supm)Tc agent in hepatobiliary system

International Nuclear Information System (INIS)

Hamada, E.S.; Barbosa, M.F. de; Theodora, M.A.; Almeida, M. de; Colturato, M.T.; Muramoto, E.; Silva, C.P.G. da.

1987-08-01

The synthesis of 2,6 diisopropyl IDA (DISIDA) and 4-n-butyl IDA (BUTIL-IDA) is described. Their spectroscopic properties, radiopharmaceutical preparation and their use as 99 (sup m)Tc complex agent in hepatobiliary studies, are also reported. (Author) [pt

Most consumed processed foods by patients on hemodialysis: Alert for phosphate-containing additives and the phosphate-to-protein ratio.

Science.gov (United States)

Watanabe, Marcela T; Araujo, Raphael M; Vogt, Barbara P; Barretti, Pasqual; Caramori, Jacqueline C T

2016-08-01

Hyperphosphatemia is common in patients with chronic kidney disease (CKD) stages IV and V because of decreased phosphorus excretion. Phosphatemia is closely related to dietary intake. Thus, a better understanding of sources of dietary phosphate consumption, absorption and restriction, particularly inorganic phosphate found in food additives, is key to prevent consequences of this complication. Our aims were to investigate the most commonly consumed processed foods by patients with CKD on hemodialysis, to analyze phosphate and protein content of these foods using chemical analysis and to compare these processed foods with fresh foods. We performed a cross-sectional descriptive analytical study using food frequency questionnaires to rank the most consumed industrialized foods and beverages. Total phosphate content was determined by metavanadate colorimetry, and nitrogen content was determined by the Kjeldahl method. Protein amounts were estimated from nitrogen content. The phosphate-to-protein ratio (mg/g) was then calculated. Processed meat protein and phosphate content were compared with the nutritional composition of fresh foods using the Brazilian Food Composition Table. Phosphate measurement results were compared with data from the Food Composition Table - Support for Nutritional Decisions. An α level of 5% was considered significant. Food frequency questionnaires were performed on 100 patients (mean age, 59 ± 14 years; 57% male). Phosphate additives were mentioned on 70% of the product labels analyzed. Proteins with phosphate-containing additives provided approximately twice as much phosphate per gram of protein compared with that of fresh foods (p processed foods are higher than those of fresh foods, as well as phosphate-to-protein ratio. A better understanding of phosphate content in foods, particularly processed foods, may contribute to better control of phosphatemia in patients with CKD. Copyright © 2016 European Society for Clinical Nutrition and

31P-Nuclear Magnetic Resonance Determination of Phosphate Compartmentation in Leaves of Reproductive Soybeans (Glycine max L.) as Affected by Phosphate Nutrition 1

Science.gov (United States)

Lauer, Michael J.; Blevins, Dale G.; Sierzputowska-Gracz, Hanna

1989-01-01

Most leaf phosphorus is remobilized to the seed during reproductive development in soybean. We determined, using 31P-NMR, the effect phosphorus remobilization has on vacuolar inorganic phosphate pool size in soybean (Glycine max [L.] Merr.) leaves with respect to phosphorus nutrition and plant development. Phosphate compartmentation between cytoplasmic and vacuolar pools was observed and followed in intact tissue grown hydroponically, at the R2, R4, and R6 growth stages. As phosphorus in the nutrient solution decreased from 0.45 to 0.05 millimolar, the vacuolar phosphate peak became less prominent relative to cytoplasmic phosphate and hexose monophosphate peaks. At a nutrient phosphate concentration of 0.05 millimolar, the vacuolar phosphate peak was not detectable. At higher levels of nutrient phosphate, as plants progressed from the R2 to the R6 growth stage, the vacuolar phosphate peak was the first to disappear, suggesting that storage phosphate was remobilized to a greater extent than metabolic phosphate. Under suboptimal phosphate nutrition (≤ 0.20 millimolar), the hexose monophosphate and cytoplasmic phosphate peaks declined earlier in reproductive development than when phosphate was present in optimal amounts. Under low phosphate concentrations (0.05 millimolar) cytoplasmic phosphate was greatly reduced. Carbon metabolism was coincidently disrupted under low phosphate nutrition as shown by the appearance of large, prominent starch grains in the leaves. Cytoplasmic phosphate, and leaf carbon metabolism dependent on it, are buffered by vacuolar phosphate until late stages of reproductive growth. Images Figure 4 PMID:16666705

The Emulsion Polymerization of Each of Vinyl Acetate and Butyl Acrylate Monomers Using bis (2-ethylhexyl) Maleate for Improving the Physicomechanical Properties of Paints and Adhesive Films

International Nuclear Information System (INIS)

Shaffei, K.A.; Moustafa, A.B.; Hamed, A.I.

2009-01-01

Improving the water sensitivity of polyvinyl acetate PVAc films as well as pressure sensitivity, adhesion and washability of poly butyl acrylate were achieved by using bis (2-ethylhexyl) maleate (BEHM). The emulsion polymerization kinetics of vinyl acetate and butyl acrylate in presence of BEHM was studied. The order of the polymerization reaction with respect to the BEHM in presence of each of vinyl acetate and butyl acrylate was studied. The physicomechanical properties of the polyvinyl acetate films and vinyl acetate-butyl acrylate copolymer films were studied in presence of BEHM and the obtained results were matched with those prepared in the presence of pluronic F 108 and showed superior values. The obtained mean average molecular weights were found to be smaller in presence of BEHM assuring the presence of chain transfer reaction.

t-Butyl group-substituted triphenylamine-containing orange-red fluorescent emitters for organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Lee, Kum Hee; Kim, Chi Sik [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of); Kim, Young Kwan, E-mail: kimyk@hongik.ac.kr [Department of Information Display, Hongik University, Seoul 121-791 (Korea, Republic of); Yoon, Seung Soo, E-mail: ssyoon@skku.edu [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of)

2012-03-30

Efficient orange-red fluorescent compounds, 4-(dicyanomethylene)-2-adamantyl-6-(4-(N-(4-tert-butylphenyl) -N-(3,5-di-tert-butylphenyl)amino)benzene)vinyl-4H-pyran (DCATP) and 2,6-bis[4-(N-(4-tert-butylphenyl)-N-(3,5-di-tert-butylphenyl)amino)benzene] vinyl-4-(dicyanomethylene)-4H-pyran (BDCTP) containing the tert-butylated triphenylamine in donor moieties, were synthesized and characterized. In these red emitters, bulky groups, such as t-butyl group and adamantane were introduced to increase the steric hindrance between the red emitters. In particular, an efficient orange-red device containing the emitter DCATP as a dopant showed a luminous and power efficiency of 6.87 cd/A and 2.70 lm/W, respectively, at 20 mA/cm{sup 2} with the CIE coordinates of (0.48, 0.50) at 7.0 V. In addition, an efficient red organic light-emitting diode using BDCTP as a dopant exhibited a luminous and power efficiency of 2.30 cd/A and 1.31 lm/W, respectively, at 20 mA/cm{sup 2} and CIE coordinates of (0.61, 0.39). - Highlights: Black-Right-Pointing-Pointer Two orange-red emitters with t-butylated triphenylamine derivatives were studied. Black-Right-Pointing-Pointer We examine changes in electron D-A and electron D-A-D type in the terminal groups. Black-Right-Pointing-Pointer Electron D-A-D type material shows improved color chromaticity.

Di-tert-butyl-chlorido(N,N-dibenzyl-dithio-carbamato)tin(IV).

Science.gov (United States)

Abdul Muthalib, Amirah Faizah; Baba, Ibrahim; Mohamed Tahir, Mohamed Ibrahim; Tiekink, Edward R T

2011-02-26

The Sn(IV) atom in the title diorganotin dithio-carbamate, [Sn(C(4)H(9))(2)(C(15)H(14)NS(2))Cl], is penta-coordinated by an asymmetrically coordinating dithio-carbamate ligand, a Cl atom and two C atoms of the Sn-bound tert-butyl groups. The resulting C(2)ClS(2) donor set defines a coordination geometry inter-mediate between square pyramidal and trigonal bipyramidal with a slight tendency towards the former.

Pentose phosphates in nucleoside interconversion and catabolism.

Science.gov (United States)

Tozzi, Maria G; Camici, Marcella; Mascia, Laura; Sgarrella, Francesco; Ipata, Piero L

2006-03-01

Ribose phosphates are either synthesized through the oxidative branch of the pentose phosphate pathway, or are supplied by nucleoside phosphorylases. The two main pentose phosphates, ribose-5-phosphate and ribose-1-phosphate, are readily interconverted by the action of phosphopentomutase. Ribose-5-phosphate is the direct precursor of 5-phosphoribosyl-1-pyrophosphate, for both de novo and 'salvage' synthesis of nucleotides. Phosphorolysis of deoxyribonucleosides is the main source of deoxyribose phosphates, which are interconvertible, through the action of phosphopentomutase. The pentose moiety of all nucleosides can serve as a carbon and energy source. During the past decade, extensive advances have been made in elucidating the pathways by which the pentose phosphates, arising from nucleoside phosphorolysis, are either recycled, without opening of their furanosidic ring, or catabolized as a carbon and energy source. We review herein the experimental knowledge on the molecular mechanisms by which (a) ribose-1-phosphate, produced by purine nucleoside phosphorylase acting catabolically, is either anabolized for pyrimidine salvage and 5-fluorouracil activation, with uridine phosphorylase acting anabolically, or recycled for nucleoside and base interconversion; (b) the nucleosides can be regarded, both in bacteria and in eukaryotic cells, as carriers of sugars, that are made available though the action of nucleoside phosphorylases. In bacteria, catabolism of nucleosides, when suitable carbon and energy sources are not available, is accomplished by a battery of nucleoside transporters and of inducible catabolic enzymes for purine and pyrimidine nucleosides and for pentose phosphates. In eukaryotic cells, the modulation of pentose phosphate production by nucleoside catabolism seems to be affected by developmental and physiological factors on enzyme levels.

Phase equilibrium conditions of semi-calthrate hydrates of (tetra-n-butyl ammonium chloride + carbon dioxide)

International Nuclear Information System (INIS)

Sun, Zhi-Gao; Jiao, Li-Jun; Zhao, Zhi-Gui; Wang, Gong-Liang; Huang, Hai-Feng

2014-01-01

Highlights: • Carbon dioxide hydrate stability zone was enlarged with the help of TBAC. • Carbon dioxide uptake into TBAC semi-clathrate hydrates is confirmed. • Equilibrium pressure of hydrate decreased with the increase of TBAC mass concentration. • The addition of TBAC reduces the formation pressures of carbon dioxide hydrate by 2.5 MPa. - Abstract: In the present work, hydrate equilibrium conditions for (tetra-n-butyl ammonium chloride (TBAC) + carbon dioxide + water) mixtures were investigated. Tetra-n-butyl ammonium chloride was reported to form a semi-clathrate hydrate. The experiments were carried out within the TBAC mass fraction range of (0.05 to 0.3). The experimental results showed that the presence of TBAC decreased the formation pressure of carbon dioxide double hydrate within the experimental temperature range. Moreover, pressure reduction was dependent on the TBAC concentration

Meal phosphate variability does not support fixed dose phosphate binder schedules for patients treated with peritoneal dialysis: a prospective cohort study.

Science.gov (United States)

Leung, Simon; McCormick, Brendan; Wagner, Jessica; Biyani, Mohan; Lavoie, Susan; Imtiaz, Rameez; Zimmerman, Deborah

2015-12-09

Removal of phosphate by peritoneal dialysis is insufficient to maintain normal serum phosphate levels such that most patients must take phosphate binders with their meals. However, phosphate 'counting' is complicated and many patients are simply prescribed a specific dose of phosphate binders with each meal. Therefore, our primary objective was to assess the variability in meal phosphate content to determine the appropriateness of this approach. In this prospective cohort study, adult patients with ESRD treated with peritoneal dialysis and prescribed phosphate binder therapy were eligible to participate. Participants were excluded from the study if they were unable to give consent, had hypercalcemia, were visually or hearing impaired or were expected to receive a renal transplant during the time of the study. After providing informed consent, patients kept a 3-day diet diary that included all foods and beverages consumed in addition to portion sizes. At the same time, patients documented the amount of phosphate binders taken with each meal. The phosphate content of the each meal was estimated using ESHA Food Processor SQL Software by a registered dietitian. Meal phosphate and binder variability were estimated by the Intra Class Correlation Coefficient (ICC) where 0 indicates maximal variability and 1 indicates no variability. Seventy-eight patients consented to participate in the study; 18 did not complete the study protocol. The patients were 60 (± 17) years, predominately male (38/60) and Caucasian (51/60). Diabetic nephropathy was the most common cause of end stage kidney disease. The daily phosphate intake including snacks ranged from 959 ± 249 to 1144 ± 362 mg. The phosphate ICC by meal: breakfast 0.63, lunch 0.16; supper 0.27. The phosphate binder ICC by meal: breakfast 0.68, lunch 0.73, supper 0.67. The standard prescription of a set number of phosphate binders with each meal is not supported by the data; patients do not appear to be adjusting their

Comparative study on in vitro biocompatibility of synthetic octacalcium phosphate and calcium phosphate ceramics used clinically.

Science.gov (United States)

Morimoto, Shinji; Anada, Takahisa; Honda, Yoshitomo; Suzuki, Osamu

2012-08-01

The present study was designed to investigate the extent to which calcium phosphate bone substitute materials, including osteoconductive octacalcium phosphate (OCP), display cytotoxic and inflammatory responses based on their dissolution in vitro. Hydroxyapatite (HA) and β-tricalcium phosphate (β-TCP) ceramics, which are clinically used, as well as dicalcium phosphate dihydrate (DCPD) and synthesized OCP were compared. The materials were well characterized by chemical analysis, x-ray diffraction and Fourier transform infrared spectroscopy. Calcium and phosphate ion concentrations and the pH of culture media after immersion of the materials were determined. The colony forming rate of Chinese hamster lung fibroblasts was estimated with extraction of the materials. Proliferation of bone marrow stromal ST-2 cells and inflammatory cytokine TNF-α production by THP-1 cells grown on the material-coated plates were examined. The materials had characteristics that corresponded to those reported. DCPD was shown to dissolve the most in the culture media, with a marked increase in phosphate ion concentration and a reduction in pH. ST-2 cells proliferated well on the materials, with the exception of DCPD, which markedly inhibited cellular growth. The colony forming capacity was the lowest on DCPD, while that of the other calcium phosphates was not altered. In contrast, TNF-α was not detected even in cells grown on DCPD, suggesting that calcium phosphate materials are essentially non-inflammatory, while the solubility of the materials can affect osteoblastic and fibroblastic cellular attachment. These results indicate that OCP is biocompatible, which is similar to the materials used clinically, such as HA. Therefore, OCP could be clinically used as a biocompatible bone substitute material.

Analyses of uranium in some phosphate commercial products

International Nuclear Information System (INIS)

Kamel, N.H.M.; Sohsah, M.; Mohammad, H.M.; Sadek, M.

2005-01-01

The raw materials used in manufacturing of phosphate fertilizer products were derived from rocks. Rocks contain a remarkable of natural radioactivity. Uranium and phosphorous were originally initiated at the same time of the initiated rocks. The purpose of this research is to investigate solubility of uranium phosphate species at the phosphate fertilizer samples, samples including; raw phosphate material, single super phosphates (SSP) granules and powdered, triple super phosphates (TSP) and phosphogypsum samples were obtained from Abu-Zabal factory in Egypt. Solubility of uranium phosphate species was estimated. It was found that, less than half of the uranium phosphate species are soluble in water. The soluble uranium may be enter into the food chains by plant. Therefore, restriction should be done in order to limit contamination of land and the public

The effect of reducing monosaccharides on the atom transfer radical polymerization of butyl methacrylate

NARCIS (Netherlands)

Vries, de Andrew; Klumperman, B.; Wet-Roos, de D.; Sanderson, R.D.

2001-01-01

The effect of various reducing monosaccharides on the rate of atom transfer radical polymerization (ATRP) of butyl methacrylate is reported in this study. The addition of reducing sugars affects the rate of ATRP positively with a 100% increase in the rate of polymerization in some cases. In

Crystal structure of 2-tert-butyl-1,3-thiazolo[4,5-b]pyridine

Directory of Open Access Journals (Sweden)

Gamal A. El-Hiti

2014-09-01

Full Text Available The title compound, C10H12N2S, does not contain any strong hydrogen-bond donors but two long C—H...N contacts are observed in the crystal structure, with the most linear interaction linking molecules along [010]. The ellipsoids of the tert-butyl group indicate large librational motion.

Sutureless vascular anastomoses by N-butyl-2 cyanoacrylate adhesive: an experimental animal study.

Science.gov (United States)

Saba, D; Yilmaz, M; Yavuz, H; Noyan, S; Avci, B; Ercan, A; Ozkan, H; Cengiz, M

2007-01-01

The purpose of this animal study was to find out whether sutureless anastomoses using N-butyl-2-cyanoacrylate were effective in the suppression of neointimal hyperplasia or not. Ten male adult mongrel dogs were used in this animal study. The animals were randomly divided into a control group (n = 5) and a study group (n = 5). The study group underwent sutureless anastomoses using N-buthyl-2-cyanoacrylate adhesive. Infrarenal aortoaortic graft was interposed using polytetrafluoroethylene. In the study group, the mean intimal thickness at the proximal anastomosis was 27.4 +/- 1.94 microm and 27.4 +/- 1.51 microm at the distal anastomosis. In the control group, the mean intimal thickness was 138.4 +/- 5.02 mum at the proximal anastomosis and 67.6 +/- 6.42 microm at the distal anastomosis. Intimal thickness at the proximal and distal anastomoses in the control group was significantly (p anastomoses using with N-butyl-2-cyanoacrylate adhesive might be a good alternative to conventional suture technique. Copyright 2007 S. Karger AG, Basel.

Phosphate Reduction in Emulsified Meat Products: Impact of Phosphate Type and Dosage on Quality Characteristics.

Science.gov (United States)

Glorieux, Seline; Goemaere, Olivier; Steen, Liselot; Fraeye, Ilse

2017-09-01

Phosphate reduction is of important industrial relevance in the manufacturing of emulsified meat products because it may give rise to a healthier product. The effect of seven different phosphate types was tested on the physicochemical and quality characteristics to select the most promising phosphate type for further cooked sausage manufacturing. Next, phosphate mass fraction was gradually reduced. Tetrasodium di- or pyrophosphate (TSPP) and sodium tripolyphosphate (STPP) increased pH, reduced structural properties, resulted in the highest emulsion stability, lowest cooking loss and had little effect on hardness. Based on the viscoelastic properties, a minimum mass fraction of 0.06% TSPP was sufficient to obtain an acceptable quality product. Rheology proved to be a very useful tool to evaluate the quality of meat products, as it gives insight in the structure of the meat product and especially the functional properties of meat proteins. Based on the obtained results, it can be concluded that the current amount of phosphate added to emulsified meat products can be significantly reduced with minimal loss of product quality.

Use of experimental design for the purge-and-trap-gas chromatography-mass spectrometry determination of methyl tert.-butyl ether, tert.-butyl alcohol and BTEX in groundwater at trace level.

Science.gov (United States)

Bianchi, F; Careri, M; Marengo, E; Musci, M

2002-10-25

An efficient method for the simultaneous determination of methyl tert.-butyl ether, tert.-butyl alcohol, benzene, toluene, ethylbenzene and xylene isomers in groundwater by purge-and-trap-gas chromatography-mass spectrometry was developed and validated. Experimental design was used to investigate the effects of temperature of extraction, time of extraction and percentage of salt added to the water samples. Regression models and desirability functions were applied to find the experimental conditions providing the highest global extraction yield. Validation was carried out in terms of limits of detection (LOD), limits of quantitation (LOQ), linearity and precision. LOD values ranging from 2.6 to 23 ng l(-1) were achieved, whereas linearity was statistically verified over two orders of magnitude for each compound. Precision was evaluated testing two concentration levels. Good results were obtained both in terms of intra-day repeatability and intermediate precision: RSD% lower than 4.5% at the highest concentration and lower than 13% at the lowest one were calculated for intra-day repeatability. A groundwater sample suspected of contamination by leaking underground petroleum storage tanks was analysed and some of the analytes were detected and quantitated.

Identification of volatile butyl rubber thermal-oxidative degradation products by cryofocusing gas chromatography/mass spectrometry (cryo-GC/MS).

Energy Technology Data Exchange (ETDEWEB)

Smith, Jonell Nicole; White, Michael Irvin; Bernstein, Robert; Hochrein, James Michael

2013-02-01

Chemical structure and physical properties of materials, such as polymers, can be altered as aging progresses, which may result in a material that is ineffective for its envisioned intent. Butyl rubber formulations, starting material, and additives were aged under thermal-oxidative conditions for up to 413 total days at up to 124 ÀC. Samples included: two formulations developed at Kansas City Plant (KCP) (#6 and #10), one commercially available formulation (#21), Laxness bromobutyl 2030 starting material, and two additives (polyethylene AC-617 and Vanax MBM). The low-molecular weight volatile thermal-oxidative degradation products that collected in the headspace over the samples were preconcentrated, separated, and detected using cryofocusing gas chromatography mass spectrometry (cryo-GC/MS). The majority of identified degradation species were alkanes, alkenes, alcohols, ketones, and aldehydes. Observations for Butyl #10 aged in an oxygen-18 enriched atmosphere (18O2) were used to verify when the source of oxygen in the applicable degradation products was from the gaseous environment rather than the polymeric mixture. For comparison purposes, Butyl #10 was also aged under non-oxidative thermal conditions using an argon atmosphere.

Di-tert-butyl 2,2′-[(biphenyl-4,4′-diyldioxy]diacetate

Directory of Open Access Journals (Sweden)

Qamar Ali

2010-07-01

Full Text Available The complete molecule of the title compound, C24H30O6, is generated by a crystallographic inversion centre. In the unique part of the molecule, the four-atom –O–CH2–C(= O–O– chain between the benzene ring and the tert-butyl group assumes a zigzag conformation [O—C—C—O torsion angle = −162.3 (1°].

Critically evaluated rate coefficients for free-radical polymerization, 5. Propagation rate coefficient for butyl acrylate

NARCIS (Netherlands)

Asua, J.M.; Beuermann, S.; Buback, M.; Castignolles, P.; Charleux, B.; Gilbert, R.G.; Hutchinson, R.A.; Leiza, J.R.; Nikitin, A.N.; Vairon, J.P.; Herk, van A.M.

2004-01-01

Propagation rate coefficients, kp, for free-radical polymerization of butyl acrylate (BA) previously reported by several groups are critically evaluated. All data were determined by the combination of pulsed-laser polymerization (PLP) and subsequent polymer analysis by size exclusion (SEC)

Risicogrenzen voor MTBE (Methyl tertiair-Butyl Ether) in bodem, sediment, grondwater, oppervlaktewater en voor drinkwaterbereiding

NARCIS (Netherlands)

Swartjes FA; Baars AJ; Fleuren RHLJ; Otte PF; LER

2004-01-01

Recentelijk is politieke commotie ontstaan ten gevolge van de mogelijke schadelijke gezondheidseffecten van Methyl tertiair-Butyl Ether (MTBE). Dit was reden voor het ministerie van VROM om het RIVM te verzoeken risicogrenzen voor MTBE in bodem, sediment, grondwater, oppervlaktewater, drinkwater en

[Phosphate-solubilizing activity of aerobic methylobacteria].

Science.gov (United States)

Agafonova, N V; Kaparullina, E N; Doronina, N V; Trotsenko, Iu A

2014-01-01

Phosphate-solubilizing activity was found in 14 strains of plant-associated aerobic methylobacteria belonging to the genera Methylophilus, Methylobacillus, Methylovorus, Methylopila, Methylobacterium, Delftia, and Ancyclobacter. The growth of methylobacteria on medium with methanol as the carbon and energy source and insoluble tricalcium phosphate as the phosphorus source was accompanied by a decrease in pH due to the accumulation of up to 7 mM formic acid as a methanol oxidation intermediate and by release of 120-280 μM phosphate ions, which can be used by both bacteria and plants. Phosphate-solubilizing activity is a newly revealed role of methylobacteria in phytosymbiosis.

Isolation and identification of a phosphate solubilising fungus from soil of a phosphate mine in Chaluse, Iran

Directory of Open Access Journals (Sweden)

Raheleh Jamshidi

2016-07-01

Full Text Available Microbial solubilisation of phosphorus from insoluble phosphates is an environmental friendly and cost effective approach in sustainable soil management. Introducing the indigenous microorganisms to soil requires shorter adaptation period and causes fewer ecological distortions than exogenous microorganisms. This study was conducted to isolate and identify the indigenous fungi for phosphate solubilisation in Mazandaran, Iran. A potent phosphate solubilising fungus was isolated from an Iranian phosphate mine and selected for solubilisation of rock phosphate (RP. The identified fungus was characterised by calmodulin-based polymerase chain reaction method as Aspergillus tubingensis SANRU (Sari Agricultural Sciences and Natural Resources University. The phosphate solubilisation ability of the fungal strain was carried out in shake-flask leaching experiments containing various concentrations of RP (1%, 2%, 4%, or 8% w/v. The maximum P solubilisation rate of 347 mg/l was achieved at 1% of RP concentration on day 9. The regression analysis indicated that the P solubilised mainly through acidification. This study shows the possibility of using A. tubingensis SANRU for application in the management of P fertilisation.

Translocation of metal phosphate via the phosphate inorganic transport system of Escherichia coli

NARCIS (Netherlands)

van Veen, H.W; Abee, T.; Kortstee, G.J J; Konings, W.N; Zehnder, A.J B

1994-01-01

P-i transport via the phosphate inorganic transport system (Pit) of Escherichia coil was studied in natural and artificial membranes. P-i uptake via Pit is dependent on the presence of divalent cations, like Mg2+, Ca2+, Co2+, or Mn2+, which form a soluble, neutral metal phosphate (MeHPO(4)) complex.

Co-precipitation of phosphate and iron limits mitochondrial phosphate availability in Saccharomyces cerevisiae lacking the yeast frataxin homologue (YFH1).

Science.gov (United States)

Seguin, Alexandra; Santos, Renata; Pain, Debkumar; Dancis, Andrew; Camadro, Jean-Michel; Lesuisse, Emmanuel

2011-02-25

Saccharomyces cerevisiae cells lacking the yeast frataxin homologue (Δyfh1) accumulate iron in the mitochondria in the form of nanoparticles of ferric phosphate. The phosphate content of Δyfh1 mitochondria was higher than that of wild-type mitochondria, but the proportion of mitochondrial phosphate that was soluble was much lower in Δyfh1 cells. The rates of phosphate and iron uptake in vitro by isolated mitochondria were higher for Δyfh1 than wild-type mitochondria, and a significant proportion of the phosphate and iron rapidly became insoluble in the mitochondrial matrix, suggesting co-precipitation of these species after oxidation of iron by oxygen. Increasing the amount of phosphate in the medium decreased the amount of iron accumulated by Δyfh1 cells and improved their growth in an iron-dependent manner, and this effect was mostly transcriptional. Overexpressing the major mitochondrial phosphate carrier, MIR1, slightly increased the concentration of soluble mitochondrial phosphate and significantly improved various mitochondrial functions (cytochromes, [Fe-S] clusters, and respiration) in Δyfh1 cells. We conclude that in Δyfh1 cells, soluble phosphate is limiting, due to its co-precipitation with iron.

Uranium production from phosphates

International Nuclear Information System (INIS)

Ketzinel, Z.; Folkman, Y.

1979-05-01

According to estimates of the world's uranium consumption, exploitation of most rich sources is expected by the 1980's. Forecasts show that the rate of uranium consumption will increase towards the end of the century. It is therefore desirable to exploit poor sources not yet in use. In the near future, the most reasonable source for developing uranium is phosphate rock. Uranium reserves in phosphates are estimated at a few million tons. Production of uranium from phosphates is as a by-product of phosphate rock processing and phosphoric acid production; it will then be possible to save the costs incurred in crushing and dissolving the rock when calculating uranium production costs. Estimates show that the U.S. wastes about 3,000 tons of uranium per annum in phosphoric acid based fertilisers. Studies have also been carried out in France, Yugoslavia and India. In Israel, during the 1950's, a small plant was operated in Haifa by 'Chemical and Phosphates'. Uranium processes have also been developed by linking with the extraction processes at Arad. Currently there is almost no activity on this subject because there are no large phosphoric acid plants which would enable production to take place on a reasonable scale. Discussions are taking place about the installation of a plant for phosphoric acid production utilising the 'wet process', producing 200 to 250,000 tons P 2 O 5 per annum. It is necessary to combine these facilities with uranium production plant. (author)

Forensic analysis of tertiary-butyl alcohol (TBA) detections in a hydrocarbon-rich groundwater basin.

Science.gov (United States)

Quast, Konrad W; Levine, Audrey D; Kester, Janet E; Fordham, Carolyn L

2016-04-01

Tertiary-butyl alcohol (TBA), a high-production volume (HPV) chemical, was sporadically detected in groundwater and coalbed methane (CBM) wells in southeastern Colorado's hydrocarbon-rich Raton Basin. TBA concentrations in shallow water wells averaged 75.1 μg/L, while detections in deeper CBM wells averaged 14.4 μg/L. The detection of TBA prompted a forensic investigation to try to identify potential sources. Historic and recent data were reviewed to determine if there was a discernable pattern of TBA occurrence. Supplemental samples from domestic water wells, monitor wells, CBM wells, surface waters, and hydraulic fracturing (HF) fluids were analyzed for TBA in conjunction with methyl tertiary-butyl ether (MTBE) and ethyl tertiary-butyl ether (ETBE), proxies for evidence of contamination from reformulated gasoline or associated oxygenates. Exploratory microbiological sampling was conducted to determine if methanotrophic organisms co-occurred with TBA in individual wells. Meaningful comparisons of historic TBA data were limited due to widely varying reporting limits. Mapping of TBA occurrence did not reveal any spatial patterns or physical associations with CBM operations or contamination plumes. Additionally, TBA was not detected in HF fluids or surface water samples. Given the widespread use of TBA in industrial and consumer products, including water well completion materials, it is likely that multiple diffuse sources exist. Exploratory data on stable isotopes, dissolved gases, and microbial profiling provide preliminary evidence that methanotrophic activity may be producing TBA from naturally occurring isobutane. Reported TBA concentrations were significantly below a conservative risk-based drinking water screening level of 8000 μg/L derived from animal toxicity data.

Electrical properties of phosphate glasses

International Nuclear Information System (INIS)

Mogus-Milankovic, A; Santic, A; Reis, S T; Day, D E

2009-01-01

Investigation of the electrical properties of phosphate glasses where transition metal oxide such as iron oxide is the network former and network modifier is presented. Phosphate glasses containing iron are electronically conducting glasses where the polaronic conduction is due to the electron hopping from low to high iron valence state. The identification of structural defects caused by ion/polaron migration, the analysis of dipolar states and electrical conductivity in iron phosphate glasses containing various alkali and mixed alkali ions was performed on the basis of the impedance spectroscopy (IS). The changes in electrical conductivity from as-quenched phosphate glass to fully crystallized glass (glass-ceramics) by IS are analyzed. A change in the characteristic features of IS follows the changes in glass and crystallized glass network. Using IS, the contribution of glass matrix, crystallized grains and grain boundary to the total electrical conductivity for iron phosphate glasses was analyzed. It was shown that decrease in conductivity is caused by discontinuities in the conduction pathways as a result of the disruption of crystalline network where two or more crystalline phases are formed. Also, phosphate-based glasses offer a unique range of biomaterials, as they form direct chemical bonding with hard/soft tissue. The surface charges of bioactive glasses are recognized to be the most important factors in determining biological responses. The improved bioactivity of the bioactive glasses as a result of the effects of the surface charges generated by electrical polarization is discussed.

Moessbauer spectroscopic characterisation of catalysts obtained by interaction between tetra-n-butyl-tin and silica or silica supported rhodium

International Nuclear Information System (INIS)

Millet, J.M.M.; Toyir, J.; Didillon, B.; Candy, J.P.; Nedez, C.; Basset, J.M.

1997-01-01

Moessbauer spectroscopy at 78 K was used to study the interaction between tetra-n-butyl-tin and the surfaces of silica or silica supported rhodium. At room temperature, the tetra-n-butyl-tin was physically adsorbed on the surfaces. After reaction under hydrogen at 373 K, the formation of grafted organometallic fragments on the Rh surface was confirmed whereas with pure silica, ≡SiO-Sn(n-C 4 H 9 ) 3 moieties were observed. After treatment at 523 K, the rhodium grafted organometallic species was completely decomposed and there was formation of a defined bimetallic RhSn compound

Study on separation of methanol-butyl methylether-1-chlorobutane system

International Nuclear Information System (INIS)

Zhang Weijiang; Cao Tianhong

2006-01-01

The separation of mixture plays an important role in chemical, petrochemical, medical biochemical industries and environmental protection engineering. Liquid mixture with azeotropic phenomenon cannot be separated by conventional distillation as well as extractive distillation. But the combination of extraction and distillation can be effective for them. This paper includes many experiments with the ternary mixture of methanol butyl methyl ether and 1-chlorobytane, which shows that the system is not ternary azeotrope and can be separated by the combination of extraction and rectification using water as extractive solvent. (authors)

The gaseous enthalpy of formation of the ionic liquid 1-butyl-3-methylimidazolium dicyanamide from combustion calorimetry, vapor pressure measurements, and ab initio calculations.

Science.gov (United States)

Emel'yanenko, Vladimir N; Verevkin, Sergey P; Heintz, Andreas

2007-04-04

Ionic liquids are attracting growing interest as alternatives to conventional molecular solvents. Experimental values of vapor pressure, enthalpy of vaporization, and enthalpy of formation of ionic liquids are the key thermodynamic quantities, which are required for the validation and development of the molecular modeling and ab initio methods toward this new class of solvents. In this work, the molar enthalpy of formation of the liquid 1-butyl-3-methylimidazolium dicyanamide, 206.2 +/- 2.5 kJ.mol-1, was measured by means of combustion calorimetry. The molar enthalpy of vaporization of 1-butyl-3-methylimidazolium dicyanamide, 157.2 +/- 1.1 kJ.mol-1, was obtained from the temperature dependence of the vapor pressure measured using the transpiration method. The latter method has been checked with measurements of 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide, where data are available from the effusion technique. The first experimental determination of the gaseous enthalpy of formation of the ionic liquid 1-butyl-3-methylimidazolium dicyanamide, 363.4 +/- 2.7 kJ.mol-1, from thermochemical measurements (combustion and transpiration) is presented. Ab initio calculations of the enthalpy of formation in the gaseous phase have been performed for 1-butyl-3-methylimidazolium dicyanamide using the G3MP2 theory. Excellent agreement with experimental results has been observed. The method developed opens a new way to obtain thermodynamic properties of ionic liquids which have not been available so far.

Hydrogen permeation resistant phosphate coatings

International Nuclear Information System (INIS)

McGuire, J.C.

1979-01-01

A method for reducing hydrogen diffusion through metal wherein the metal is coated with a phosphate-radical-containing, phosphate-glass-forming material on at least one surface thereof. The coating is then heated to at least 350 0 C to form a phosphate glass. This method is especially applicable to nuclear reactors to minimize tritium diffusion. The coating is preferably formed with a solution of phosphoric acid which may also contain compounds such as MnSO 4 , SiO 2 and Na 2 Cr 2 0 7 . (author)

Hydrogen permeation resistant phosphate coatings

International Nuclear Information System (INIS)

McGuire, J.C.

1979-01-01

A method for reducing hydrogen diffusion through metal is described. The metal is coated with a phosphate-radical-containing, phosphate-glass-forming material on at least one surface. The coating is then heated to at least 350 0 C to form a phosphate glass. This method is especially applicable to nuclear reactors to minimize tritium diffusion. The coating is preferably formed with a solution of phosphoric acid which may also contain compounds such as MnSO 4 , SiO 2 and Na 2 Cr 2 O 7 . (author)

MONITORED NATURAL ATTENUATION OF TERTIARY BUTYL ALCOHOL (TBA) IN GROUND WATER AT GASOLINE SPILL SITES

Science.gov (United States)

The state agencies that implement the Underground Storage Tank program rely heavily on Monitored Natural Attenuation (MNA) to clean up contaminants such as benzene and methyl tertiary butyl ether (MTBE) at gasoline spill sites. This is possible because the contaminants are biolo...

Transfer of Some Major and Trace Elements From Phosphate Rock to Super-Phosphate Fertilizers

International Nuclear Information System (INIS)

El-Reefya, H.I.; Bin-Jaz, A.A.; Zaied, M.E.; Badran, H.M.; Badran, H.M.

2014-01-01

This study assesses the transfer of some major and trace elements from phosphate rock (PR) to single (SSP) and triple (TSP) superphosphate fertilizers. Samples from a fertilizer plant and local market were collected and analyzed using inductively coupled plasma spectrometer. Cluster analysis indicated that the inner-relationship among the concentration of the elements in PR, SSP, and TSP are different. Only one element (Mo) has concentration in SSP higher than phosphate rock. The production process of these two types of superphosphate leads to transfer higher portion of Mn, B, Cu, Mo, Sr, and V present in the phosphate rock to SSP than TSP. The potentially hazardous element Cd is also transmitted more to SSP than TSP, and Cr is equally transferred to both types. The mean elemental concentrations normalized to the percentage of P 2 O 5 demonstrate that for most elements they are the higher concentrations in SSP are linked to the phosphate contents

Phosphate vibrations as reporters of DNA hydration

Science.gov (United States)

Corcelli, Steven

The asymmetric phosphate stretch vibrational frequency is extraordinarily sensitive to its local solvent environment. Using density functional theory calculations on the model compound dimethyl phosphate, the asymmetric phosphate stretch vibrational frequency was found to shift linearly with the magnitude of an electric field along the symmetry axis of the PO2 moiety (i.e. the asymmetric phosphate stretch is an excellent linear vibrational Stark effect probe). With this linear relationship established, asymmetric phosphate stretch vibrational frequencies were computed during the course of a molecular dynamics simulation of fully hydrated DNA. Moreover, contributions to shifts in the frequencies from subpopulations of water molecules (e.g. backbone, minor groove, major groove, etc.) were calculated to reveal how phosphate vibrations report the onset of DNA hydration in experiments that vary the relative humidity of non-condensing (dry) DNA samples.

Densities and Kinematic Viscosities for the Systems Benzene + Methyl Formate, Benzene + Ethyl Formate, Benzene + Propyl Formate, and Benzene + Butyl Formate

DEFF Research Database (Denmark)

Emmerling, Uwe; Rasmussen, Peter

1998-01-01

a Redlich-Kister type of expression with temperature-independent parameters and the data for the systems benzene + ethyl formate, benzene + propyl formate, and benzene + butyl formate with temperature-dependent parameters. The viscosities have furthermore been compared to values predicted by means of the GC......Densities and kinematic viscosities have been measured for the system benzene + methyl formate at 20°C and for the systems benzene + ethyl formate, benzene + propyl formate, and benzene + butyl formate from 20°C to 50°C. The results for the system benzene + methyl formate have been correlated using...

Sonochemical precipitation of amorphous uranium phosphates from trialkyl phosphate solutions and their thermal conversion to UP2O7

Czech Academy of Sciences Publication Activity Database

Doroshenko, I.; Žurková, J.; Moravec, Z.; Bezdička, Petr; Pinkas, J.

2015-01-01

Roč. 26, SEP (2015), s. 157-162 ISSN 1350-4177 Institutional support: RVO:61388980 Keywords : Uranium * Phosphates * Sonochemistry * Nuclear waste * Trimethyl phosphate * Triethyl phosphate Subject RIV: CA - Inorganic Chemistry Impact factor: 4.556, year: 2015

Influence of Emulsion Polymerization Techniques to Particle Size of Copoly(styrene/butyl acrylate/methyl methacrylate

Directory of Open Access Journals (Sweden)

Tresye Utari

2008-04-01

Full Text Available In the majority of applications, particle size and particle size distribution are highly significant factors that determine the properties of a polymer dispersion, such as its flow behavior or its stability. For example, a coating material with small particle size will give smooth coating result, good adhesive strength, good water resistance and latex stability. This article describes influence of various emulsion polymerization techniques to particle size of copoly(styrene/butyl acrylate/methyl methacrylate with mix surfactant SDBS linear chain and nonyl fenol (EO10 and initiator ammonium persulphate. DSC data, solid content and IR spectrum showed that copoly(styrene/butyl acrylate/methyl methacrylate was produced. Batch emulsion polymerization technique gave the highest particle size i.e. 615 nm and also the highest % conversion of monomer i.e. 97%. The more concentration of monomer was seeded to initial charge gave greater particle size and greater poly dispersity index.

Voltammetric determination of butylated hydroxyanisol in biodiesel, mineral and synthetic oils using gold electrode

Czech Academy of Sciences Publication Activity Database

Tomášková, M.; Chýlková, J.; Jehlička, V.; Navrátil, Tomáš; Šelešovská, R.

2013-01-01

Roč. 19, č. 2013 (2013), s. 155-172 ISSN 1211-5541 R&D Projects: GA ČR(CZ) GAP208/12/1645 Grant - others:GA ČR(CZ) GP13-21409P Program:GP Institutional support: RVO:61388955 Keywords : voltammetry * butylated hydroxyanisol * gold electrode Subject RIV: CF - Physical ; Theoretical Chemistry

Coal anion structure and chemistry of coal alkylation. Fourth quarterly progress report, December 1, 1977--February 28, 1978. [Carbon atoms in butyl groups

Energy Technology Data Exchange (ETDEWEB)

Stock, L.M.

1978-01-01

Three research problems are in progress. First, work is progressing well concerning the methods appropriate for the reductive alkylation of Illinois No. 6 coal samples. We have investigated the influence of the leaving group on the conversion of the Illinois coal to a soluble material. We find that the n-butyl iodide is more effective than other n-butyl halides. Second, preliminary results have been obtained concerning the distribution of hydrogen and deuterium atoms in the reaction of Illinois No. 6 coal samples with perdeuteriotetralin at 400/sup 0/C. Third, the nuclear magnetic resonance spectra of appropriate model compounds with n-butyl groups have been tabulated for comparison with the spectroscopic results obtained from coal alkylation products. Fourth, the chromatographic procedures necessary for the separation of the coal samples are being developed.

Cerebrospinal Fluid Phosphate in Delirium after Hip Fracture

Directory of Open Access Journals (Sweden)

Ane-Victoria Idland

2017-09-01

Full Text Available Aims: Phosphate is essential for neuronal activity. We aimed to investigate whether delirium is associated with altered phosphate concentrations in cerebrospinal fluid (CSF and serum. Methods: Seventy-seven patients with hip fracture were assessed for delirium before and after acute surgery. Prefracture dementia was diagnosed by an expert panel. Phosphate was measured in CSF obtained immediately before spinal anesthesia (n = 77 and in serum (n = 47. CSF from 23 cognitively healthy elderly patients undergoing spinal anesthesia was also analyzed. Results: Hip fracture patients with prevalent delirium had higher CSF phosphate concentrations than those without delirium (median 0.63 vs. 0.55 mmol/L, p = 0.001. In analyses stratified on dementia status, this difference was only significant in patients with dementia. Serum phosphate was ∼1 mmol/L; there was no association between serum phosphate concentration and delirium status. CSF phosphate did not correlate with serum levels. Conclusion: Patients with delirium superimposed on dementia have elevated phosphate levels.

Radical-induced dephosphorylation of fructose phosphates in aqueous solution

International Nuclear Information System (INIS)

Zegota, H.; Sonntag, C. von

1981-01-01

Oxygen free N 2 O-saturated aqueous solutions of D-fructose-1-phosphate and D-fructose-6-phosphate were γ-irradiated. Inorganic phosphate and phosphate free sugars (containing four to six carbon atoms) were identified and their G-values measured. D-Fructose-1-phosphate yields (G-values in parentheses) inorganic phosphate (1.6), hexos-2-ulose (0.12), 6-deoxy-2,5-hexodiulose (0.16), tetrulose (0.05) and 3-deoxytetrulose (0.15). D-Fructose-6-phosphate yields inorganic phosphate (1.7), hexos-5-ulose (0.1), 6-deoxy-2,5-hexodiulose (0.36), 3-deoxy-2,5-hexodiulose and 2-deoxyhexos-5-ulose (together 0.18). On treatment with alkaline phosphatase further deoxy sugars were recognized and in fructose-1-phosphate G(6-deoxy-2,5-hexodiulose) was increased to a G-value of 0.4. Dephosphorylation is considered to occur mainly after OH attack at C-5 and C-1 in fructose-1-phosphate and at C-5 and C-6 in fructose-6-phosphate. Reaction mechanisms are discussed. (orig.)

Vinyl Acetate/butyl acrylate/acrylate Research of Ternary Soap-free Emulsion Polymerization

Directory of Open Access Journals (Sweden)

Xiao Li-guang

2016-01-01

Full Text Available Through the vinyl acetate/butyl acrylate/acrylic acrylic emulsion preparation without soap vinegar, with solid content, gel, emulsion stability and film forming properties and tensile strength as the main index to study the effect of raw materials on the properties of emulsion. Through the infrared spectrometer soap-free emulsion for microscopic analysis research. Study of the ternary soap-free vinegar acrylic emulsion with good performance.

Biological fate of butylated hydroxytoluene (BHT) in rats, (2)

International Nuclear Information System (INIS)

Nakagawa, Yoshio; Ikawa, Mieko; Hiraga, Kogo

1976-01-01

The fate of butylated hydroxytoluene (BHT) in hepatocytes was examined. 14 C-labelled BHT was administered once orally to rats, and the fractionation of hepatocytes was made in course of time to detect the subcellular distribution of radioactivity. The BHT incorporation into livers reached the maximum 6 hours after the administration. Most of the radioactivity was localized in the supernatant fraction at the beginning of the administration, but it decreased gradually, and the radioactivity in microsome fraction increased in time course. The radioactivity in the supernatant fraction and in serum assumed two forms; namely high molecular compound bound with protein and free low molecular compound. (Kobatake, H.)

Iron phosphate glass containing simulated fast reactor waste: Characterization and comparison with pristine iron phosphate glass

International Nuclear Information System (INIS)

Joseph, Kitheri; Asuvathraman, R.; Venkata Krishnan, R.; Ravindran, T.R.; Govindaraj, R.; Govindan Kutty, K.V.; Vasudeva Rao, P.R.

2014-01-01

Detailed characterization was carried out on an iron phosphate glass waste form containing 20 wt.% of a simulated nuclear waste. High temperature viscosity measurement was carried out by the rotating spindle method. The Fe 3+ /Fe ratio and structure of this waste loaded iron phosphate glass was investigated using Mössbauer and Raman spectroscopy respectively. Specific heat measurement was carried out in the temperature range of 300–700 K using differential scanning calorimeter. Isoconversional kinetic analysis was employed to understand the crystallization behavior of the waste loaded iron phosphate glass. The glass forming ability and glass stability of the waste loaded glass were also evaluated. All the measured properties of the waste loaded glass were compared with the characteristics of pristine iron phosphate glass

Solid state {sup 1}H spin-lattice relaxation and isolated-molecule and cluster electronic structure calculations in organic molecular solids: The relationship between structure and methyl group and t-butyl group rotation

Energy Technology Data Exchange (ETDEWEB)

Wang, Xianlong, E-mail: WangXianlong@uestc.edu.cn, E-mail: pbeckman@brynmawr.edu [Key Laboratory for NeuroInformation of Ministry of Education, School of Life Science and Technology, University of Electronic Science and Technology of China, 4 North Jianshe Rd., 2nd Section, Chengdu 610054 (China); Mallory, Frank B. [Department of Chemistry, Bryn Mawr College, 101 North Merion Ave., Bryn Mawr, Pennsylvania 19010-2899 (United States); Mallory, Clelia W. [Department of Chemistry, Bryn Mawr College, 101 North Merion Ave., Bryn Mawr, Pennsylvania 19010-2899 (United States); Department of Chemistry, University of Pennsylvania, Philadelphia, Pennsylvania 19104-6323 (United States); Odhner, Hosanna R.; Beckmann, Peter A., E-mail: WangXianlong@uestc.edu.cn, E-mail: pbeckman@brynmawr.edu [Department of Physics, Bryn Mawr College, 101 North Merion Ave., Bryn Mawr, Pennsylvania 19010-2899 (United States)

2014-05-21

We report ab initio density functional theory electronic structure calculations of rotational barriers for t-butyl groups and their constituent methyl groups both in the isolated molecules and in central molecules in clusters built from the X-ray structure in four t-butyl aromatic compounds. The X-ray structures have been reported previously. We also report and interpret the temperature dependence of the solid state {sup 1}H nuclear magnetic resonance spin-lattice relaxation rate at 8.50, 22.5, and 53.0 MHz in one of the four compounds. Such experiments for the other three have been reported previously. We compare the computed barriers for methyl group and t-butyl group rotation in a central target molecule in the cluster with the activation energies determined from fitting the {sup 1}H NMR spin-lattice relaxation data. We formulate a dynamical model for the superposition of t-butyl group rotation and the rotation of the t-butyl group's constituent methyl groups. The four compounds are 2,7-di-t-butylpyrene, 1,4-di-t-butylbenzene, 2,6-di-t-butylnaphthalene, and 3-t-butylchrysene. We comment on the unusual ground state orientation of the t-butyl groups in the crystal of the pyrene and we comment on the unusually high rotational barrier of these t-butyl groups.

Calcium phosphates for biomedical applications

Directory of Open Access Journals (Sweden)

Maria Canillas

2017-05-01

Full Text Available The history of calcium phosphates in the medicine field starts in 1769 when the first evidence of its existence in the bone tissue is discovered. Since then, the interest for calcium phosphates has increased among the scientific community. Their study has been developed in parallel with new advances in materials sciences, medicine or tissue engineering areas. Bone tissue engineering is the field where calcium phosphates have had a great importance. While the first bioceramics are selected according to bioinert, biocompatibility and mechanical properties with the aim to replace bone tissue damaged, calcium phosphates open the way to the bone tissue regeneration challenge. Nowadays, they are present in the majority of commercial products directed to repair or regenerate damaged bone tissue. Finally, in the last few decades, they have been suggested and studied as drug delivering devices and as vehicles of DNA and RNA for the future generation therapies.

Preparation of calcium phosphate paste

International Nuclear Information System (INIS)

Mohd Reusmaazran Yusof; Norzita Yaacob; Idris Besar; Che Seman Mahmood; Rusnah Mustafa

2010-01-01

Calcium phosphate paste were prepared by mixing between calcium sodium potassium phosphate, Ca 2 NaK (PO 4 ) 2 (CSPP) and monocalcium phosphate monohydrate, Ca(H 2 PO 4 ) 2 .H 2 O (MCPM). CSPP were obtained by reaction between calcium hydrogen phosphate (CaHPO 4 ), potassium carbonate (K 2 CO 3 ) and sodium carbonate (Na 2 CO 3 ) in solid state sintering process followed by quenching in air at 1000 degree Celsius. The paste was aging in simulated body fluid (SBF) for 0.5, 1, 3, 6, 12, 24, 48 hrs, 3, 7 and 14 days. The morphological investigation indicated the formation of apatite crystal were first growth after 24 hours. The obvious growth of apatite crystal was shown at 3 days. The obvious growth of apatite crystal was shown in 7 and 14 days indicated the prediction of paste would have rapid reaction with bone after implantation. (author)

Calcium phosphates for biomedical applications

Energy Technology Data Exchange (ETDEWEB)

Canillas, M.; Pena, P.; Aza, A.H. de; Rodriguez, M.A.

2017-07-01

The history of calcium phosphates in the medicine field starts in 1769 when the first evidence of its existence in the bone tissue is discovered. Since then, the interest for calcium phosphates has increased among the scientific community. Their study has been developed in parallel with new advances in materials sciences, medicine or tissue engineering areas. Bone tissue engineering is the field where calcium phosphates have had a great importance. While the first bioceramics are selected according to bioinert, biocompatibility and mechanical properties with the aim to replace bone tissue damaged, calcium phosphates open the way to the bone tissue regeneration challenge. Nowadays, they are present in the majority of commercial products directed to repair or regenerate damaged bone tissue. Finally, in the last few decades, they have been suggested and studied as drug delivering devices and as vehicles of DNA and RNA for the future generation therapies. (Author)

Conditions promoting and restraining agronomic effectiveness of water-insoluble phosphate sources, in particular phosphate rock (PR): I. Indices of phosphate rock use opportunity (PRUOIS) and of phosphate rock suitability for direct use (PRSIDU)

International Nuclear Information System (INIS)

Borlan, Z.; Gavriluta, I.; Soare, M.; Stefanescu, D.; Alexandrescu, A.

2002-01-01

Several issues of phosphate rock (PR) use are discussed in this paper. Maize for green fodder (Zea mays L) and ryegrass (Lolium multiflorum Lam.) were grown in 7 kg of dry soil and in small pots of 1.25 kg dry soil capacity, respectively, on several base unsaturated soils belonging to Hapludoll and Hapludalf soil groups. The amount of phosphate rock (PR) to apply was based on experimental data considering soil adsorbed acidity (Ah), humus content (H 2 ), cation exchange capacity (T), sum of exchangeable bases (SEB) and mobile (easily soluble) phosphate content (P A L) in the soil. The factors were combined in a rock phosphate use, opportunity index of the soil (PRUOIS): PRUOIS=(A h *H 2 *100)/SEB*10 0.0245*P AL Rock phosphate suitability for direct use was evaluated by means of the rate of PR-P dissolution (PRPRS) in a 0.6% ammonium heptamolybdate in 0.01M calcium chloride solution (ppm P) and by carbonate content (%CaCO 3 ) in PR. Both of these parameters combined provided a phosphate rock suitability index for direct use (PRSIDU): PRSIDU [ppmP/min]=PRPRS*(1-0.03*CaCO 3 ) Water insoluble P sources studied were PR from Kola-Russia, Morocco, Kneifiss-Siria, El Hassa-Jordan, Gafsa- Tunisia, North-Carolina (USA), and Arad-Israel. All PRs were compared with TSP applied at the same rate of P. Neither PRUOIS or PRSIDU considered separately could satisfactorily explain the variance of PR efficiency. An index obtained by multiplicative combination of PRUOIS x PRSIDU did correlate significantly with indices on the agronomic efficiency of PR. (author)

Carbamoylcholine analogs as nicotinic acetylcholine receptor agonists--structural modifications of 3-(dimethylamino)butyl dimethylcarbamate (DMABC)

DEFF Research Database (Denmark)

Hansen, Camilla Petrycer; Jensen, Anders Asbjørn; Balle, Thomas

2009-01-01

Compounds based on the 3-(dimethylamino)butyl dimethylcarbamate (DMABC) scaffold were synthesized and pharmacologically characterized at the alpha(4)beta(2), alpha(3)beta(4,) alpha(4)beta(4) and alpha(7) neuronal nicotinic acetylcholine receptors (nAChRs). The carbamate functionality and a small...

Impaired Phosphate Tolerance Revealed With an Acute Oral Challenge.

Science.gov (United States)

Turner, Mandy E; White, Christine A; Hopman, Wilma M; Ward, Emilie C; Jeronimo, Paul S; Adams, Michael A; Holden, Rachel M

2018-01-01

Elevated serum phosphate is consistently linked with cardiovascular disease (CVD) events and mortality in the setting of normal and impaired kidney function. However, serum phosphate does not often exceed the upper limit of normal until glomerular filtration rate (GFR) falls below 30 mL/min/m 2 . It was hypothesized that the response to an oral, bioavailable phosphate load will unmask impaired phosphate tolerance, a maladaptation not revealed by baseline serum phosphate concentrations. In this study, rats with varying kidney function as well as normo-phosphatemic human subjects, with inulin-measured GFR (13.2 to 128.3mL/min), received an oral phosphate load. Hormonal and urinary responses were evaluated over 2 hours. Results revealed that the more rapid elevation of serum phosphate was associated with subjects and rats with higher levels of kidney function, greater responsiveness to acute changes in parathyroid hormone (PTH), and significantly more urinary phosphate at 2 hours. In humans, increases in urinary phosphate to creatinine ratio did not correlate with baseline serum phosphate concentrations but did correlate strongly to early increase of serum phosphate. The blunted rise in serum phosphate in rats with CKD was not the result of altered absorption. This result suggests acute tissue deposition may be altered in the setting of kidney function impairment. Early recognition of impaired phosphate tolerance could translate to important interventions, such as dietary phosphate restriction or phosphate binders, being initiated at much higher levels of kidney function than is current practice. © 2017 American Society for Bone and Mineral Research. © 2017 American Society for Bone and Mineral Research.

Phosphate Reduction in Emulsifi ed Meat Products: Impact of Phosphate Type and Dosage on Quality Characteristics

Directory of Open Access Journals (Sweden)

Seline Glorieux

2017-01-01

Full Text Available Phosphate reduction is of important industrial relevance in the manufacturing of emulsifi ed meat products because it may give rise to a healthier product. The eff ect of seven diff erent phosphate types was tested on the physicochemical and quality characteristics to select the most promising phosphate type for further cooked sausage manufacturing. Next, phosphate mass fraction was gradually reduced. Tetrasodium di- or pyrophosphate (TSPP and sodium tripolyphosphate (STPP increased pH, reduced structural properties, resulted in the highest emulsion stability, lowest cooking loss and had litt le eff ect on hardness. Based on the viscoelastic properties, a minimum mass fraction of 0.06 % TSPP was suffi cient to obtain an acceptable quality product. Rheology proved to be a very useful tool to evaluate the quality of meat products, as it gives insight in the structure of the meat product and especially the functional properties of meat proteins. Based on the obtained results, it can be concluded that the current amount of phosphate added to emulsifi ed meat products can be signifi cantly reduced with minimal loss of product quality.

Energetic Materials Center Report--Small-Scale Safety and Thermal Testing Evaluation of Butyl Nitrate

Energy Technology Data Exchange (ETDEWEB)

Hsu, Peter C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Energetic Materials Center; Reynolds, John G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States). Energetic Materials Center

2013-04-26

Butyl Nitrate (BN) was examined by Small-Scale Safety and Thermal (SSST) Testing techniques to determine its sensitivity to impact, friction, spark and thermal exposure simulating handling and storage conditions. Under the conditions tested, the BN exhibits thermal sensitivity above 150 °C, and does not exhibit sensitive to impact, friction or spark.

Volumetric properties of the (tetrahydrofuran + water) and (tetra-n-butyl ammonium bromide + water) systems: Experimental measurements and correlations

International Nuclear Information System (INIS)

Belandria, Veronica; Mohammadi, Amir H.; Richon, Dominique

2009-01-01

In this communication, we report experimental density data for the binary mixtures of (water + tetrahydrofuran) and (water + tetra-n-butyl ammonium bromide) at atmospheric pressure and various temperatures. The densities were measured using an Anton Paar TM digital vibrating-tube densimeter. For the (tetrahydrofuran + water) system, excess molar volumes have been calculated using the experimental densities and correlated using the Redlich-Kister equation. The Redlich-Kister equation parameters have been adjusted on experimental results. The partial molar volumes and partial excess molar volumes at infinite dilution have also been calculated for each component. A simple density equation was finally applied to correlate the measured density of the (tetra-n-butyl ammonium bromide + water) system.

Formation of poly(butyl 2-cyanoacrylate) microcapsules and the microencapsulation of aqueous solutions of [125I]-labelled proteins

International Nuclear Information System (INIS)

Wood, D.A.; Whateley, T.L.; Florence, A.T.

1981-01-01

Some featrues of the polymerization reaction of butyl 2-cyanoacrylate at different aqueous/organic solvent interfaces have been investigated. In particular, the effects of pH and the presence of protein on the formation of microcapsules by in situ interfacial polymerization of butyl 2-cyanoacrylate in w/o emulsions have been studied. [ 125 I]-labelled proteins have been used to study the procedure as a method of microencapsulating enzymes or other proteins within potentially biodegradable membranes. Preliminary in vitro degradation studies suggest that degradation of the microcapsules is inhibited by low levels of their breakdown products, thus allowing the storage of the microcapsules as aqueous suspensions for prolonged periods in sealed containers. (Auth.)

Keggin type inorganic-organic hybrid material containing Mn(II) monosubstituted phosphotungstate and S-(+)-sec-butyl amine: Synthesis and characterization

Energy Technology Data Exchange (ETDEWEB)

Patel, Ketan [Chemistry Department, Faculty of Science, M.S. University of Baroda, Vadodara 390 002 (India); Patel, Anjali, E-mail: aupatel_chem@yahoo.com [Chemistry Department, Faculty of Science, M.S. University of Baroda, Vadodara 390 002 (India)

2012-02-15

Graphical abstract: A new organic-inorganic hybrid material containing Keggin type manganese substituted phosphotungstate and S-(+)-sec-butyl amine was synthesized and systematically characterized. Highlights: Black-Right-Pointing-Pointer New hybrid material comprising Mn substituted phosphotungstate (PW{sub 11}Mn) and S-(+)-sec-butyl amine (SBA) was synthesized. Black-Right-Pointing-Pointer The spectral studies reveal the attachment of SBA to the PW{sub 11}Mn without any distortion of structure. Black-Right-Pointing-Pointer The synthesized material comprises chirality. Black-Right-Pointing-Pointer The synthesized hybrid material can be used as a heterogeneous catalyst for carrying out asymmetric synthesis. -- Abstract: A new inorganic-organic POM-based hybrid material comprising Keggin type mono manganese substituted phosphotungstate and enantiopure S-(+)-sec-butyl amine was synthesized in an aqueous media by simple ligand substitution method. The synthesized hybrid material was systematically characterized in solid as well as solution by various physicochemical techniques such as elemental analysis, TGA, UV-vis, FT-IR, ESR and multinuclear solution NMR ({sup 31}P, {sup 1}H, {sup 13}C). The presence of chirality in the synthesized material was confirmed by CD spectroscopy and polarimeter. The above study reveals the attachment of S-(+)-sec-butyl amine to Keggin type mono manganese substituted phosphotungstate through N {yields} Mn bond. It also indicates the retainment of Keggin unit and presence of chirality in the synthesized material. An attempt was made to use the synthesized material as a heterogeneous catalyst for carrying out aerobic asymmetric oxidation of styrene using molecular oxygen. The catalyst shows the potential of being used as a stable recyclable catalytic material after simple regeneration without significant loss in conversion.

Biotemplate synthesis of monodispersed iron phosphate hollow microspheres

International Nuclear Information System (INIS)

Cao Feng; Li Dongxu

2010-01-01

Monodispersed iron phosphate hollow microspheres with a high degree of crystallization were prepared through a facile in situ deposition method using rape pollen grains as a biotemplate. The functional group on the surface of the pollen grains could adsorb Fe 3+ , which provided the nucleation sites for growth of iron phosphate nanoparticles. After being sintered at 600 deg. C for 10 h, the pollen grains were removed and iron phosphate hollow microspheres were obtained. A scanning electron microscope and x-ray diffraction were applied to characterize the morphology and crystalline structure of the pollen grains, iron phosphate-coated pollen grains and iron phosphate hollow microspheres. Differential scanning calorimetry and thermogravity analyses were performed to investigate the thermal behavior of the iron phosphate-coated pollen grains during the calcinations. Energy dispersive spectroscopy and Fourier transform infrared spectroscopy were utilized to investigate the interaction between the pollen grains and iron phosphate. The effect of the pollen wall on the surface morphology of these iron phosphate hollow microspheres was also proven in this work.

Biotemplate synthesis of monodispersed iron phosphate hollow microspheres

Energy Technology Data Exchange (ETDEWEB)

Cao Feng; Li Dongxu, E-mail: dongxuli@njut.edu.c [College of Materials Science and Engineering, Nanjing University of Technology, Jiangsu Nanjing 210009 (China)

2010-03-15

Monodispersed iron phosphate hollow microspheres with a high degree of crystallization were prepared through a facile in situ deposition method using rape pollen grains as a biotemplate. The functional group on the surface of the pollen grains could adsorb Fe{sup 3+}, which provided the nucleation sites for growth of iron phosphate nanoparticles. After being sintered at 600 deg. C for 10 h, the pollen grains were removed and iron phosphate hollow microspheres were obtained. A scanning electron microscope and x-ray diffraction were applied to characterize the morphology and crystalline structure of the pollen grains, iron phosphate-coated pollen grains and iron phosphate hollow microspheres. Differential scanning calorimetry and thermogravity analyses were performed to investigate the thermal behavior of the iron phosphate-coated pollen grains during the calcinations. Energy dispersive spectroscopy and Fourier transform infrared spectroscopy were utilized to investigate the interaction between the pollen grains and iron phosphate. The effect of the pollen wall on the surface morphology of these iron phosphate hollow microspheres was also proven in this work.

The Effect of Moderate Dietary Protein and Phosphate Restriction on Calcium-Phosphate Homeostasis in Healthy Older Cats.

Science.gov (United States)

Geddes, R F; Biourge, V; Chang, Y; Syme, H M; Elliott, J

2016-09-01

Dietary phosphate and protein restriction decreases plasma PTH and FGF-23 concentrations and improves survival time in azotemic cats, but has not been examined in cats that are not azotemic. Feeding a moderately protein- and phosphate-restricted diet decreases PTH and FGF-23 in healthy older cats and thereby slows progression to azotemic CKD. A total of 54 healthy, client-owned cats (≥ 9 years). Prospective double-blinded randomized placebo-controlled trial. Cats were assigned to test diet (protein 76 g/Mcal and phosphate 1.6 g/Mcal) or control diet (protein 86 g/Mcal and phosphate 2.6 g/Mcal) and monitored for 18 months. Changes in variables over time and effect of diet were assessed by linear mixed models. A total of 26 cats ate test diet and 28 cats ate control diet. There was a significant effect of diet on urinary fractional excretion of phosphate (P = 0.045), plasma PTH (P = 0.005), and ionized calcium concentrations (P = 0.018), but not plasma phosphate, FGF-23, or creatinine concentrations. Plasma PTH concentrations did not significantly change in cats fed the test diet (P = 0.62) but increased over time in cats fed the control diet (P = 0.001). There was no significant treatment effect of the test diet on development of azotemic CKD (3 of 26 (12%) test versus 3 of 28 (11%) control, odds ratio 1.09 (95% CI 0.13-8.94), P = 0.92). Feeding a moderately protein- and phosphate-restricted diet has effects on calcium-phosphate homeostasis in healthy older cats and is well tolerated. This might have an impact on renal function and could be useful in early chronic kidney disease. Copyright © 2016 The Authors. Journal of Veterinary Internal Medicine published by Wiley Periodicals, Inc. on behalf of the American College of Veterinary Internal Medicine.

INHALATION EXPOSURE TO METHYL TERT-BUTYL ETHER (MTBE) AND DIBROMOCHLOROMETHANE (DBCM) USING CONTINUOUS BREATH ANALYSIS

Science.gov (United States)

The oxygenate methyl tert-butyl ether (MTBE) has been added to gasoline to help meet national ambient air quality standards in those parts of the U.S. that are non-compliant for carbon monoxide. Although MTBE has provided important health benefits in terms of reduced haza...

Transdermal uptake of diethyl phthalate and di(n-butyl) phthalate directly from air: Experimental verification

DEFF Research Database (Denmark)

Weschler, Charles J.; Bekö, Gabriel; Koch, Holger M.

2015-01-01

of phthalate esters. Objectives: This study investigated transdermal uptake, directly from air, of diethyl phthalate (DEP) and di(n-butyl) phthalate (DnBP) in humans. Methods: In a series of experiments, six human participants were exposed for 6 hr in a chamber containing deliberately elevated air...

Process Intensification of Enzymatic Fatty Acid Butyl Ester Synthesis Using a Continuous Centrifugal Contactor Separator

NARCIS (Netherlands)

Ilmi, Miftahul; Abduh, Muhammad Yusuf; Hommes, Arne; Winkelman, Jozef; Hidayat, C.; Heeres, Hero

2018-01-01

Fatty acid butyl esters were synthesized from sunflower oil with 1-butanol using a homogeneous Rhizomucor miehei lipase in a biphasic organic (triglyceride, 1-butanol, hexane)– water (with enzyme) system in a continuous setup consisting of a cascade of a stirred tank reactor and a continuous

Isolation of phosphatase-producing phosphate solubilizing bacteria from Loriya hot spring: Investigation of phosphate solubilizing in the presence of different parameters

Directory of Open Access Journals (Sweden)

Maryam Parhamfar

2014-04-01

Full Text Available Introduction: Biofertilizers are the microorganisms that can convert useless nutrient to usable compounds. Unlike fertilizer, cost of biofertilizer production is low and doesn’t produce ecosystem pollution. Phosphate fertilizers can be replaced by phosphate biofertilizer to produce improvement. So, it is necessary to screen the climate-compatible phosphate solubilizing bacteria. Materials and methods: In this project samples were picked up from Loriya hot spring, which are located in Jiroft. Samples were incubated in PKV medium for 3 days. Screening of phosphate solubilizing bacteria was performed on the specific media, based on clear area diameter. The best bacterium was identified based on 16s rDNA gene. Phosphate solubilizing activity of this strain was considered in different carbon, nitrogen, phosphate and pH sources. Results: Sequence alignment and phylogenetic tree results show that B. sp. LOR033 is closely related to Bacillus licheniformis, with 97% homology. In addition, results show that maximum enzyme production was performed after 2 days that incubation pH was decreased simultaneously when the time was increased. Carbon sources investigation show that glucose is the most appropriate in enzyme production and phosphate releasing. Furthermore, results show that the optimum initial pH for phytase production was pH5.0. Different phosphate sources show that tricalcium phosphate has the suitable effect on enzyme activity in three days of incubation. Discussion and conclusion: Phosphatase enzyme production capacity, growth in acidic pH and phosphate solubilizing potential in different salt and phosphate sources show that this strain has considerable importance as biofertilizers.

Aqueous phosphate removal using nanoscale zero-valent iron

International Nuclear Information System (INIS)

Almeelbi, Talal; Bezbaruah, Achintya

2012-01-01

Nanoscale zero-valent iron (NZVI) particles have been used for the remediation of a wide variety of contaminants. NZVI particles have high reactivity because of high reactive surface area. In this study, NZVI slurry was successfully used for phosphate removal and recovery. Batch studies conducted using different concentrations of phosphate (1, 5, and 10 mg PO 4 3− -P/L with 400 mg NZVI/L) removed ∼96 to 100 % phosphate in 30 min. Efficacy of the NZVI in phosphate removal was found to 13.9 times higher than micro-ZVI (MZVI) particles with same NZVI and MZVI surface area concentrations used in batch reactors. Ionic strength, sulfate, nitrate, and humic substances present in the water affected in phosphate removal by NZVI but they may not have any practical significance in phosphate removal in the field. Phosphate recovery batch study indicated that better recovery is achieved at higher pH and it decreased with lowering of the pH of the aqueous solution. Maximum phosphate recovery of ∼78 % was achieved in 30 min at pH 12. The successful rapid removal of phosphate by NZVI from aqueous solution is expected to have great ramification for cleaning up nutrient rich waters.

Research and engineering assessment of biological solubilization of phosphate

Energy Technology Data Exchange (ETDEWEB)

Rogers, R.D.; McIlwain, M.E.; Losinski, S.J.; Taylor, D.D.

1993-03-01

This research and engineering assessment examined a microbial phosphate solubilization process as a method of recovering phosphate from phosphorus containing ore compared to the existing wet acid and electric arc methods. A total of 860 microbial isolates, collected from a range of natural environments were tested for their ability to solubilize phosphate from rock phosphate. A bacterium (Pseudomonas cepacia) was selected for extensive characterization and evaluation of the mechanism of phosphate solubilization and of process engineering parameters necessary to recover phosphate from rock phosphate. These studies found that concentration of hydrogen ion and production of organic acids arising from oxidation of the carbon source facilitated microbial solubilization of both pure chemical insoluble phosphate compounds and phosphate rock. Genetic studies found that phosphate solubilization was linked to an enzyme system (glucose dehydrogenase). Process-related studies found that a critical solids density of 1% by weight (ore to liquid) was necessary for optimal solubilization. An engineering analysis evaluated the cost and energy requirements for a 2 million ton per year sized plant, whose size was selected to be comparable to existing wet acid plants.

21 CFR 582.1781 - Sodium aluminum phosphate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium aluminum phosphate. 582.1781 Section 582.1781 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Additives § 582.1781 Sodium aluminum phosphate. (a) Product. Sodium aluminum phosphate. (b) Conditions of...

21 CFR 182.1781 - Sodium aluminum phosphate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium aluminum phosphate. 182.1781 Section 182.1781 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Food Substances § 182.1781 Sodium aluminum phosphate. (a) Product. Sodium aluminum phosphate. (b...

Formation of Germa-ketenimine on the Ge(100) Surface by Adsorption of tert-Butyl Isocyanide.

Science.gov (United States)

Shong, Bonggeun; Yoo, Jong Suk; Sandoval, Tania E; Bent, Stacey F

2017-06-28

Reactions of the (100) surfaces of Ge and Si with organic molecules have been generally understood within the concept of "dimers" formed by the 2 × 1 surface reconstruction. In this work, the adsorption of tert-butyl isocyanide on the Ge(100)-2 × 1 surface at large exposures is investigated under ultrahigh vacuum conditions. A combination of infrared spectroscopy, X-ray photoelectron spectroscopy, and temperature-programmed desorption experiments along with dispersion-corrected density functional theory calculations is used to determine the surface products. Upon adsorption of a dense monolayer of tert-butyl isocyanide, a product whose structure resembles a germa-ketenimine (N=C=Ge) with σ donation toward and π back-donation from the Ge(100) surface appears. Formation of this structure involves divalent-type surface Ge atoms that arise from cleavage of the Ge(100)-2 × 1 surface dimers. Our results reveal an unprecedented class of reactions of organic molecules at the Ge(100) surface.

Working-up sugar-beet molasses in the acetone-butyl alcohol plants in Poland

Energy Technology Data Exchange (ETDEWEB)

Logotkin, I S; Zaritskii, I M

1959-01-01

The basic setup common to all Polish acetone and butanol plants is the addition of rye or wheat meal to the fermentation. A culture of Clostridium acetobutylicum, after spore formation, is mixed in a special apparatus with the meal, where it is kept for 18 hours at 37/sup 0/ and then treated with molasses; a culture is prepared which is used later in the fermentor. Independently a mixture of meal and molasses is mixed in an autoclave with H/sub 2/O, sterilized, and cooled. The resulting mash is mixed in the fermentor with the culture mentioned, where the fermentation liberates CO/sub 2/ and hydrogen which are recovered. The mixture is then heated, distilled, and rectified, where, in addition to slops, the desired products are obtained. The Polish plants figure that for each long ton of sugar contained in the molasses they recover butyl alcohol 178.0, acetone 83.7, and ethanol 7.3kg, and they use in addition to the molasses and bacilli cultures 58.4 tons of steam and 16 kg of NaOH long ton of the acetone-butyl alcohol mixture recovered.

Separation of Poly(styrene-block-t-butyl methacrylate) Copolymers by Various Liquid Chromatography Techniques

Science.gov (United States)

Šmigovec Ljubič, Tina; Pahovnik, David; Žigon, Majda; Žagar, Ema

2012-01-01

The separation of a mixture of three poly(styrene-block-t-butyl methacrylate) copolymers (PS-b-PtBMA), consisting of polystyrene (PS) blocks of similar length and t-butyl methacrylate (PtBMA) blocks of different lengths, was performed using various chromatographic techniques, that is, a gradient liquid chromatography on reversed-phase (C18 and C8) and normal-phase columns, a liquid chromatography under critical conditions for polystyrene as well as a fully automated two-dimensional liquid chromatography that separates block copolymers by chemical composition in the first dimension and by molar mass in the second dimension. The results show that a partial separation of the mixture of PS-b-PtBMA copolymers can be achieved only by gradient liquid chromatography on reversed-phase columns. The coelution of the two block copolymers is ascribed to a much shorter PtBMA block length, compared to the PS block, as well as a small difference in the length of the PtBMA block in two of these copolymers, which was confirmed by SEC-MALS and NMR spectroscopy. PMID:22489207

Removal mechanism of phosphate from aqueous solution by fly ash.

Science.gov (United States)

Lu, S G; Bai, S Q; Zhu, L; Shan, H D

2009-01-15

This work studied the effectiveness of fly ash in removing phosphate from aqueous solution and its related removal mechanism. The adsorption and precipitation of phosphate by fly ash were investigated separately in order to evaluate their role in the removal of phosphate. Results showed that the removal of phosphate by fly ash was rapid. The removal percentage of phosphate in the first 5min reached 68-96% of the maximum removal of phosphate by fly ash. The removal processes of phosphate by fly ash included a fast and large removal representing precipitation, then a slower and longer removal due to adsorption. The adsorption of phosphate on fly ash could be described well by Freundlich isotherm equation. The pH and Ca2+ concentration of fly ash suspension were decreased with the addition of phosphate, which suggests that calcium phosphate precipitation is a major mechanism of the phosphate removal. Comparison of the relative contribution of the adsorption and precipitation to the total removal of phosphate by fly ash showed that the adsorption accounted for 30-34% of the total removal of phosphate, depending on the content of CaO in fly ash. XRD patterns of the fly ash before and after phosphate adsorption revealed that phosphate salt (CaHPO4 x 2H2O) was formed in the adsorption process. Therefore, the removal of phosphate by fly ash can be attributed to the formation of phosphate precipitation as a brushite and the adsorption on hydroxylated oxides. The results suggested that the use of fly ash could be a promising solution to the removal of phosphate in the wastewater treatment and pollution control.

Isolation and screening phosphate solubilizers from composts as biofertilizer

International Nuclear Information System (INIS)

Phua Choo Kwai Hoe; Khairuddin Abdul Rahim; Latiffah Norddin; Abdul Razak Ruslan

2006-01-01

Phosphate solubilizers are miroorganisms that able to solubilize insoluble inorganic phosphate compounds or hydrolyze organic phosphate to inorganic P. Therefore make the P to be available for plant and consequently enhance plant growth and yield. Recently, phosphate solubilizing microorganisms has been shown to play an important role in the biofertilizer industry. Fifty-one bacterial were isolated from eleven composts. Most of the phosphate solubilizers were isolated from natural farming composted compost and normal composting compost. This shows that both of these composts are more suitable to use for phosphate solubilizer isolation compare commercial composts. Fourteen of the isolates were found to be phosphate solubilizers. These isolates produced a clear zone on the phosphate agar plates, showing their potential as biofertilizer. AP3 was significantly produced the largest clear zone compared with other isolates. This indicates that isolate AP 3 could be a good phosphate solubilizer. Thus, their effectiveness in the greenhouse and field should be evaluated. (Author)

Uranium endowments in phosphate rock

Energy Technology Data Exchange (ETDEWEB)

Ulrich, Andrea E., E-mail: andrea.ulrich@env.ethz.ch [Institute for Environmental Decisions (IED), Natural and Social Science Interface, ETH Zurich Universitässtrasse 22, 8092 Zurich (Switzerland); Institute for Agricultural Sciences, Plant Nutrition, ETH Zurich, Eschikon 33, 8315 Lindau (Switzerland); Schnug, Ewald, E-mail: e.schnug@tu-braunschweig.de [Department of Life Sciences, Technical University of Braunschweig, Pockelsstraße 14, D-38106 Braunschweig (Germany); Prasser, Horst-Michael, E-mail: prasser@lke.mavt.ethz.ch [Institute of Energy Technology, Laboratory of Nuclear Energy Systems, ETH Zurich, Sonneggstrasse 3, 8092 Zurich (Switzerland); Frossard, Emmanuel, E-mail: emmanuel.frossard@usys.ethz.ch [Institute for Agricultural Sciences, Plant Nutrition, ETH Zurich, Eschikon 33, 8315 Lindau (Switzerland)

2014-04-01

This study seeks to identify and specify the components that make up the prospects of U recovery from phosphate rock. A systems approach is taken. The assessment includes i) reviewing past recovery experience and lessons learned; ii) identifying factors that determine recovery; and iii) establishing a contemporary evaluation of U endowments in phosphate rock reserves, as well as the available and recoverable amounts from phosphate rock and phosphoric acid production. We find that in the past, recovery did not fulfill its potential and that the breakup of the Soviet Union worsened then-favorable recovery market conditions in the 1990s. We find that an estimated 5.7 million tU may be recoverable from phosphate rock reserves. In 2010, the recoverable tU from phosphate rock and phosphoric acid production may have been 15,000 tU and 11,000 tU, respectively. This could have filled the world U supply-demand gap for nuclear energy production. The results suggest that the U.S., Morocco, Tunisia, and Russia would be particularly well-suited to recover U, taking infrastructural considerations into account. We demonstrate future research needs, as well as sustainability orientations. We conclude that in order to promote investment and production, it seems necessary to establish long-term contracts at guaranteed prices, ensuring profitability for phosphoric acid producers. - Highlights: • We identify components that underlie the recovery of uranium from phosphate rock. • We estimate that 11,000 tU may have been recoverable from phosphoric acid in 2010. • Recovery is a resource conservation and environmental pollution control strategy. • To ensure investment in recovery technology, profitability needs to be secured.

Uranium endowments in phosphate rock

International Nuclear Information System (INIS)

Ulrich, Andrea E.; Schnug, Ewald; Prasser, Horst-Michael; Frossard, Emmanuel

2014-01-01

This study seeks to identify and specify the components that make up the prospects of U recovery from phosphate rock. A systems approach is taken. The assessment includes i) reviewing past recovery experience and lessons learned; ii) identifying factors that determine recovery; and iii) establishing a contemporary evaluation of U endowments in phosphate rock reserves, as well as the available and recoverable amounts from phosphate rock and phosphoric acid production. We find that in the past, recovery did not fulfill its potential and that the breakup of the Soviet Union worsened then-favorable recovery market conditions in the 1990s. We find that an estimated 5.7 million tU may be recoverable from phosphate rock reserves. In 2010, the recoverable tU from phosphate rock and phosphoric acid production may have been 15,000 tU and 11,000 tU, respectively. This could have filled the world U supply-demand gap for nuclear energy production. The results suggest that the U.S., Morocco, Tunisia, and Russia would be particularly well-suited to recover U, taking infrastructural considerations into account. We demonstrate future research needs, as well as sustainability orientations. We conclude that in order to promote investment and production, it seems necessary to establish long-term contracts at guaranteed prices, ensuring profitability for phosphoric acid producers. - Highlights: • We identify components that underlie the recovery of uranium from phosphate rock. • We estimate that 11,000 tU may have been recoverable from phosphoric acid in 2010. • Recovery is a resource conservation and environmental pollution control strategy. • To ensure investment in recovery technology, profitability needs to be secured

Phosphate Salts

Science.gov (United States)

... body. They are involved in cell structure, energy transport and storage, vitamin function, and numerous other processes ... Phosphate-containing foods and beverages include cola, wine, beer, whole grain cereals, nuts, dairy products and some ...

Synthesis of amorphous acid iron phosphate nanoparticles

International Nuclear Information System (INIS)

Palacios, E.; Leret, P.; Fernández, J. F.; Aza, A. H. De; Rodríguez, M. A.

2012-01-01

A simple method to precipitate nanoparticles of iron phosphate with acid character has been developed in which the control of pH allows to obtain amorphous nanoparticles. The acid aging of the precipitated amorphous nanoparticles favored the P–O bond strength that contributes to the surface reordering, the surface roughness and the increase of the phosphate acid character. The thermal behavior of the acid iron phosphate nanoparticles has been also studied and the phosphate polymerization at 400 °C produces strong compacts of amorphous nanoparticles with interconnected porosity.

Measurement of tributyl phosphate (TBP) in groundwater at a legacy radioactive waste site and its possible role in contaminant mobilisation.

Science.gov (United States)

Rowling, Brett; Kinsela, Andrew S; Comarmond, M Josick; Hughes, Catherine E; Harrison, Jennifer J; Johansen, Mathew P; Payne, Timothy E

2017-11-01

At many legacy radioactive waste sites, organic compounds have been co-disposed, which may be a factor in mobilisation of radionuclides at these sites. Tri-butyl phosphate (TBP) is a component of waste streams from the nuclear fuel cycle, where it has been used in separating actinides during processing of nuclear fuels. Analyses of ground waters from the Little Forest Legacy Site (LFLS) in eastern Australia were undertaken using solid-phase extraction (SPE) followed by gas chromatographic mass spectrometry (GCMS). The results indicate the presence of TBP several decades after waste disposal, with TBP only being detected in the immediate vicinity of the main disposal area. TBP is generally considered to degrade in the environment relatively rapidly. Therefore, it is likely that its presence is due to relatively recent releases of TBP, possibly stemming from leakage due to container degradation. The ongoing presence and solubility of TBP has the potential to provide a mechanism for nuclide mobilisation, with implications for long term management of LFLS and similar legacy waste sites. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Are Polyphosphates or Phosphate Esters Prebiotic Reagents?

Science.gov (United States)

Keefe, Anthony D.; Miller, Stanley L.

1995-01-01

It is widely held that there was a phosphate compound in prebiotic chemistry that played the role of adenosine triphosphate and that the first living organisms had ribose-phosphate in the backbone of their genetic material. However, there are no known efficient prebiotic synthesis of high-energy phosphates or phosphate esters. We review the occurrence of phosphates in nature, the efficiency of the volcanic synthesis of P4O10, the efficiency of polyphosphate synthesis by heating phosphate minerals under geological conditions, and the use of high-energy organic compounds such as cyanamide or hydrogen cyanide. These are shown to be inefficient processes especially when the hydrolysis of the polyphosphates is taken into account. For example, if a whole atmosphere of methane or carbon monoxide were converted to cyanide which somehow synthesized polyphosphates quantitatively, the polyphosphate concentration in the ocean would still have been insignificant. We also attempted to find more efficient high-energy polymerizing agents by spark discharge syntheses, but without success. There may still be undiscovered robust prebiotic syntheses of polyphosphates, or mechanisms for concentrating them, but we conclude that phosphate esters may not have been constituents of the first genetic material. Phosphoanhydrides are also unlikely as prebiotic energy sources.

21 CFR 582.5697 - Riboflavin-5-phosphate.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Riboflavin-5-phosphate. 582.5697 Section 582.5697 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5697 Riboflavin-5-phosphate. (a) Product. Riboflavin-5-phosphate. (b) Conditions of use...

RATE CONSTANTS FOR THE REACTIONS OF OH RADICALS AND CL ATOMS WITH DI-N-PROPYL ETHER AND DI-N-BUTYL ETHER AND THEIR DEUTERATED ANALOGS. (R825252)

Science.gov (United States)

Using relative rate methods, rate constants for the gas-phase reactions of OH radicals and Cl atoms with di-n-propyl ether, di-n-propyl ether-d14, di-n-butyl ether and di-n-butyl ether-d18 have been measured at 296 ? 2 K and atmos...

Sulfuric acid functional zirconium (or aluminum) incorporated mesoporous MCM-48 solid acid catalysts for alkylation of phenol with tert-butyl alcohol

International Nuclear Information System (INIS)

Jiang, Tingshun; Cheng, Jinlian; Liu, Wangping; Fu, Lie; Zhou, Xuping; Zhao, Qian; Yin, Hengbo

2014-01-01

Several zirconium (or aluminum) incorporated mesoporous MCM-48 solid acid catalysts (SO 4 2− /Zr-MCM-48 and SO 4 2− /Al-MCM-48) were prepared by the impregnation method and their physicochemical properties were characterized by means of XRD, FT-IR, TEM, NH 3 -TPD and N 2 physical adsorption. Also, the catalytic activities of these solid acid catalysts were evaluated by the alkylation of phenol with tert-butyl alcohol. The effect of weight hour space velocity (WHSV), reaction time and reaction temperature on catalytic properties was also studied. The results show that the SO 4 2− /Zr-MCM-48 and SO 4 2− /Al-MCM-48 still have good mesoporous structure and long range ordering. Compared with the Zr (or Al)–MCM-48 samples, SO 4 2− /Zr-MCM-48 and SO 4 2− /Al-MCM-48 solid acid catalysts have strong acidity and exhibit high activities in alkylation reaction of phenol with tert-butyl alcohol. The SO 4 2− /Zr-MCM-48-25 (molar ratio of Si/Zr=0.04) catalyst was found to be the most promising and gave the highest phenol conversion among all catalysts. A maximum phenol conversion of 91.6% with 4-tert-butyl phenol (4-TBP) selectivity of 81.8% was achieved when the molar ratio of tert-butyl alcohol:phenol is 2:1, reaction time is 2 h, the WHSV is 2 h −1 and the reaction temperature is 140 °C. - Highlights: • Sulfuric acid functional mesoporous solid acid catalysts were prepared via impregnation method. • The alkylation of phenol with tert-butyl alcohol was carried out over these solid acid catalysts. • The catalytic activity of SO 4 2− /Zr-MCM-48-25 catalyst is much higher than that of the others. • A maximum phenol conversion of 91.6% was achieved under optimum reaction conditions for SO 4 2− /Zr-MCM-48-25

Photostabilization of Rhodamine 6G in acetone by β-carotene and t-butyl hydroxyanisole

OpenAIRE

Aoki, Keisuke; Matsuda, Masahiro; Yamamoto, Daisuke; Abe, Yasuhiro; Akutsu, Shinya; Fujita, Koichi; Doi, Kazutaka; Kobayashi, Masami

2011-01-01

The photostability of Rhodamine 6G is of crucial importance for the organic light-emitting display of mobilephones. Photobleaching of Rhodamine 6G in acetone was not protected by β-carotene, but was efficientlyphotostabilized by t-butyl hydroxyanisole. The results indicate that photobleaching of Rhodamine 6G inacetone was not caused by singlet oxygen but some radical species.

A Case of Successful Ablation of a Gastrophrenic Fistula with n-Butyl-2-Cyanoacrylate

Directory of Open Access Journals (Sweden)

Ashish Mahajan

2008-01-01

Full Text Available A 79-year-old woman with a fistula between a subphrenic abscess and the fundus of the stomach was successfully treated with n-Butyl-2-Cyanoacrylate. Conservative management had failed. Clinical presentation, treatment progress and imaging findings by computed tomography scan, ultrasound, gastroscopy and fluoroscopy are presented, along with a brief review of the relevant literature.

Bilateral transrenal ureteral occlusion by means of n-butyl cyanoacrylate and AMPLATZER vascular plug

Directory of Open Access Journals (Sweden)

Rosario F Grasso

2014-01-01

Full Text Available AMPLATZER vascular plug is a widely used embolic agent. In the present paper, we present a case of an 86-year-old female patient who underwent bilateral ureteral occlusion by means of AMPLATZER vascular plug II coupled to n-butyl cyanoacrylate (NBCA because of recurring pyelonephritis following cystectomy with subsequent bilateral ureterosigmoidostomy (sec. Mainz type II.

Transformation mechanism of n-butyl terminated Si nanoparticles embedded into Si1-xCx nanocomposites mixed with Si nanoparticles and C atoms

International Nuclear Information System (INIS)

Shin, J.W.; Oh, D.H.; Kim, T.W.; Cho, W.J.

2009-01-01

Bright-field transmission electron microscopy (TEM) images, high-resolution TEM (HRTEM) images, and fast-Fourier transformed electron-diffraction patterns showed that n-butyl terminated Si nanoparticles were aggregated. The formation of Si 1-x C x nanocomposites was mixed with Si nanoparticles and C atoms embedded in a SiO 2 layer due to the diffusion of C atoms from n-butyl termination shells into aggregated Si nanoparticles. Atomic force microscopy (AFM) images showed that the Si 1-x C x nanocomposites mixed with Si nanoparticles and C atoms existed in almost all regions of the SiO 2 layer. The formation mechanism of Si nanoparticles and the transformation mechanism of n-butyl terminated Si nanoparticles embedded into Si 1-x C x nanocomposites mixed with Si nanoparticles and C atoms are described on the basis of the TEM, HRTEM, and AFM results. These results can help to improve the understanding of the formation mechanism of Si nanoparticles.

Two-year drinking water carcinogenicity study of methyl tertiary-butyl ether (MTBE) in Wistar rats.

Science.gov (United States)

Dodd, Darol; Willson, Gabrielle; Parkinson, Horace; Bermudez, Edilberto

2013-07-01

Methyl tertiary-butyl ether (MTBE) has been used as a gasoline additive to reduce tailpipe emissions and its use has been discontinued. There remains a concern that drinking water sources have been contaminated with MTBE. A two-year drinking water carcinogenicity study of MTBE was conducted in Wistar rats (males, 0, 0.5, 3, 7.5 mg ml(-1); and females, 0, 0.5, 3, and 15 mg ml(-1)). Body weights were unaffected and water consumption was reduced in MTBE-exposed males and females. Wet weights of male kidneys were increased at the end of two years of exposure to 7.5 mg ml(-1) MTBE. Chronic progressive nephropathy was observed in males and females, was more severe in males, and was exacerbated in the high MTBE exposure groups. Brain was the only tissue with a statistically significant finding of neoplasms. One astrocytoma (1/50) was found in a female rat (15 mg ml(-1)). The incidence of brain astrocytomas in male rats was 1/50, 1/50, 1/50 and 4/50 for the 0, 0.5, 3 and 7.5 mg ml(-1) exposure groups, respectively. This was a marginally significant statistical trend, but not statistically significant when pairwise comparisons were made or when multiple comparisons were taken into account. The incidence of astrocytoma fell within historical control ranges for Wistar rats, and the brain has not been identified as a target organ following chronic administration of MTBE, ethyl tert-butyl ether, or tertiary butyl alcohol (in drinking water) to mice and rats. We conclude that the astrocytomas observed in this study are not associated with exposure to MTBE. Copyright © 2011 John Wiley & Sons, Ltd.

Structural Basis for Substrate Specificity in Phosphate Binding (beta/alpha)8-Barrels: D-Allulose 6-Phosphate 3-Epimerase from Escherichia coli K-12

Energy Technology Data Exchange (ETDEWEB)

Chan,K.; Fedorov, A.; Almo, S.; Gerlt, J.

2008-01-01

Enzymes that share the ({beta}/{alpha})8-barrel fold catalyze a diverse range of reactions. Many utilize phosphorylated substrates and share a conserved C-terminal ({beta}/a)2-quarter barrel subdomain that provides a binding motif for the dianionic phosphate group. We recently reported functional and structural studies of d-ribulose 5-phosphate 3-epimerase (RPE) from Streptococcus pyogenes that catalyzes the equilibration of the pentulose 5-phosphates d-ribulose 5-phosphate and d-xylulose 5-phosphate in the pentose phosphate pathway [J. Akana, A. A. Fedorov, E. Fedorov, W. R. P. Novack, P. C. Babbitt, S. C. Almo, and J. A. Gerlt (2006) Biochemistry 45, 2493-2503]. We now report functional and structural studies of d-allulose 6-phosphate 3-epimerase (ALSE) from Escherichia coli K-12 that catalyzes the equilibration of the hexulose 6-phosphates d-allulose 6-phosphate and d-fructose 6-phosphate in a catabolic pathway for d-allose. ALSE and RPE prefer their physiological substrates but are promiscuous for each other's substrate. The active sites (RPE complexed with d-xylitol 5-phosphate and ALSE complexed with d-glucitol 6-phosphate) are superimposable (as expected from their 39% sequence identity), with the exception of the phosphate binding motif. The loop following the eighth {beta}-strand in ALSE is one residue longer than the homologous loop in RPE, so the binding site for the hexulose 6-phosphate substrate/product in ALSE is elongated relative to that for the pentulose 5-phosphate substrate/product in RPE. We constructed three single-residue deletion mutants of the loop in ALSE, ?T196, ?S197 and ?G198, to investigate the structural bases for the differing substrate specificities; for each, the promiscuity is altered so that d-ribulose 5-phosphate is the preferred substrate. The changes in kcat/Km are dominated by changes in kcat, suggesting that substrate discrimination results from differential transition state stabilization. In both ALSE and RPE, the

Mineral phosphate solubilizing bacterial community in agro-ecosystem

African Journals Online (AJOL)

STORAGESEVER

2009-12-15

Dec 15, 2009 ... patterns. Four insoluble phosphate sources; purulia rock phosphate (PRP), mussourie rock phosphate. (MRP) ... community composition analysis (Garland, 1996a) and ..... the threshold level that enabled only a few species to.

A study of butyl acetate synthesis. 4-reaction kinetics

Directory of Open Access Journals (Sweden)

Álvaro Orjuela Londoño

2006-05-01

Full Text Available This work was aimed at studying liquid-phase acetic acid and butyl alcohol esterification reaction (P atm =0.76 Bar,using an ion exchange resin (Lewatit K-2431 as catalyst. The effect of the absence of internal and external mass transport on catalyst particles was established in the research conditions used here. A set of assays to determine the effect of catalyst load (0.5%, 1%, 2% w/w temperature (73°C, 80°C, 87°C and molar ratio (1:2, 1:1, 2:1 acid/alcohol on reaction rate was carried out and both LHHW and pseudo-homogeneous kinetic expressions were obtained, these being in good agreement with the experimental data.

[Phosphate solubilization of Aureobasidium pullulan F4 and its mechanism].

Science.gov (United States)

Wang, Dan; Zhan, Jing; Sun, Qing-Ye

2014-07-01

The Aureobasidium pullulans F4 was isolated from the rhizosphere of Hippochaete ramosissimum in Tongguanshan mine wasteland in Tongling City, Anhui Province. Liquid culture was conducted with four kinds of phosphorus sources, calcium phosphate, aluminum phosphate, ferric phosphate and rock phosphate to determine the pH, dissolved phosphorus, phosphorus in the bacteria and organic acid in the solution. The results showed that the phosphate solubilization by A. pullulans F4 varied with phosphorus sources, which decreased in order of aluminum phosphate > ferric phosphate, calcium phosphate > rock phosphate. The amounts of dissolved phosphorus in the different treatments were all higher than 200 mg x L(-1). The pH of the medium dropped immediately in 48 h, and the aluminum phosphate and ferric phosphate treatments showed a greater decrease in pH than the calcium phosphate and rock phosphate treatments. The organic acid synthesized by A. pullulans F4 included oxalic acid, citric acid and tartaric acid, and oxalic acid, among which oxalic acid was the dominated component. The phosphate dissolving capacity of A. pullulans F4 showed no significant correlation with organic acid, but significantly correlated with the pH. The available phosphorus was significantly improved with the combined application of A. pullulans F4 and glucose, suggesting A. pullulans F4 was a potent candidate for remediation of copper mine wastelands.

Solid State Multinuclear Magnetic Resonance Investigation of Electrolyte Decomposition Products on Lithium Ion Electrodes

Science.gov (United States)

DeSilva, J .H. S. R.; Udinwe, V.; Sideris, P. J.; Smart, M. C.; Krause, F. C.; Hwang, C.; Smith, K. A.; Greenbaum, S. G.

2012-01-01

Solid electrolyte interphase (SEI) formation in lithium ion cells prepared with advanced electrolytes is investigated by solid state multinuclear (7Li, 19F, 31P) magnetic resonance (NMR) measurements of electrode materials harvested from cycled cells subjected to an accelerated aging protocol. The electrolyte composition is varied to include the addition of fluorinated carbonates and triphenyl phosphate (TPP, a flame retardant). In addition to species associated with LiPF6 decomposition, cathode NMR spectra are characterized by the presence of compounds originating from the TPP additive. Substantial amounts of LiF are observed in the anodes as well as compounds originating from the fluorinated carbonates.

Estimation of solubility of organo-phosphorus extractants by P determination using molybdovanadophosphoric acid method

International Nuclear Information System (INIS)

Gill, J.S.; Kotekar, M.K.; Singh, H.

2005-01-01

Solvent extraction processes have been found to be suitable for uranium recovery from phosphoric acid. Various extractants like di-2-ethyl hexylphosphoric acid (D2EHPA), di-nonylphenyl phosphoric acid (DNPPA) and synergistic agents like tri-butyl phosphate (TBP), tri-octyl phosphine oxide (TOPO) have been used in liquid-liquid extraction of uranium from phosphoric acid. Contents of these organo-phosphorus compounds in aqueous raffinates need estimation for process requirements. Solubility of Tri-butyl phosphate (TBP) and Di-2-ethylhexyl phosphoric acid (D2EHPA) extractants have been determined in different media of water, oxalic acid (0.6M) and sulphuric acid (3.75M) solutions. These compounds were estimated by determining their phosphorus (P) contents employing molybdovanadophosphoric acid method, after digesting and solubalizing them in nitric and perchloric acid. (author)

Hanford phosphate precipitation filtration process evaluation

International Nuclear Information System (INIS)

Walker, B.W.; McCabe, D.J.

1997-01-01

The purpose of this filter study was to evaluate cross-flow filtration as effective solid-liquid separation technology for treating Hanford wastes, outline operating conditions for equipment, examine the expected filter flow rates, and determine proper cleaning. A proposed Hanford waste pre-treatment process uses sodium hydroxide at high temperature to remove aluminum from sludge. This process also dissolves phosphates. Upon cooling to 40 degrees centigrade the phosphates form a Na7(PO4)2F9H2O precipitate which must be removed prior to further treatment. Filter studies were conducted with a phosphate slurry simulant to evaluate whether 0.5 micron cross-flow sintered metal Mott filters can separate the phosphate precipitate from the wash solutions. The simulant was recirculated through the filters at room temperature and filtration performance data was collected

On the interaction of molybdenum cyanide complexes with hydroperoxide of tertiary butyl

International Nuclear Information System (INIS)

Vretsena, N.B.; Nikipanchuk, M.V.; Chernyak, B.I.

1979-01-01

Conducted is investigation of interaction of potassium dioxotetracyanomolybdate (4) K 4 [MoO 2 (CN) 4 ], potassium oxotetracyanomolybdate (2) K 4 [MoO(CN) 4 ] and potassium tetracyanomolybdate K 4 [Mo(CN) 4 ] in CCl 4 and hydroperoxide of tertiary butyl medium, (HPTB). Shown is the process complex mechanism which leads to molybdenum oxidation in complexes and also to coordination and HPTB decomposition. Calculated are parameters of complex formation process of molybdenum with HPTB cyanide complexes

Simultaneous clostridial fermentation, lipase-catalyzed esterification, and ester extraction to enrich diesel with butyl butyrate

NARCIS (Netherlands)

Berg, C. van den; Heeres, A.S.; Wielen, L.A.M. van der; Straathof, A.J.J.

2013-01-01

The recovery of 1-butanol from fermentation broth is energy-intensive since typical concentrations in fermentation broth are below 20gL -1. To prevent butanol inhibition and high downstream processing costs, we aimed at producing butyl esters instead of 1-butanol. It is shown that it is possible to

Biosynthesis and characterization of layered iron phosphate

International Nuclear Information System (INIS)

Zhou Weijia; He Wen; Wang Meiting; Zhang Xudong; Yan Shunpu; Tian Xiuying; Sun Xianan; Han Xiuxiu; Li Peng

2008-01-01

Layered iron phosphate with uniform morphology has been synthesized by a precipitation method with yeast cells as a biosurfactant. The yeast cells are used to regulate the nucleation and growth of layered iron phosphate. The uniform layered structure is characterized by small-angle x-ray diffraction (SAXD), scanning electron microscopy (SEM) and atomic force microscopy (AFM) analyses. Fourier transform infrared spectroscopy (FT-IR) is used to analyze the chemical bond linkages in organic–inorganic hybrid iron phosphate. The likely synthetic mechanism of nucleation and oriented growth is discussed. The electrical conductivity of hybrid iron phosphate heat-treated at different temperatures is presented

Gene mdpC plays a regulatory role in the methyl-tert-butyl ether degradation pathway of Methylibium petroleiphilum strain PM1.

Science.gov (United States)

Joshi, Geetika; Schmidt, Radomir; Scow, Kate M; Denison, Michael S; Hristova, Krassimira R

2015-04-01

Among the few bacteria known to utilize methyl tert-butyl ether (MTBE) as a sole carbon source, Methylibium petroleiphilum PM1 is a well-characterized organism with a sequenced genome; however, knowledge of the genetic regulation of its MTBE degradation pathway is limited. We investigated the role of a putative transcriptional activator gene, mdpC, in the induction of MTBE-degradation genes mdpA (encoding MTBE monooxygenase) and mdpJ (encoding tert-butyl alcohol hydroxylase) of strain PM1 in a gene-knockout mutant mdpC(-). We also utilized quantitative reverse transcriptase PCR assays targeting genes mdpA, mdpJ and mdpC to determine the effects of the mutation on transcription of these genes. Our results indicate that gene mdpC is involved in the induction of both mdpA and mdpJ in response to MTBE and tert-butyl alcohol (TBA) exposure in PM1. An additional independent mechanism may be involved in the induction of mdpJ in the presence of TBA. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Sorption of cesium on titanium and zirconium phosphates

International Nuclear Information System (INIS)

Lebedev, V.N.; Mel'nik, N.A.; Rudenko, A.V.

2003-01-01

Titanium and zirconium phosphates were prepared from mineral raw materials of the Kola Peninsula. Their capability to recover cesium cations from the model solutions and liquid radioactive waste (LRW) was studied. Titanium phosphate prepared from solutions formed by titanite breakdown demonstrates greater distribution coefficients of cesium as compared to zirconium phosphate. Titanium phosphate as a cheaper agent featuring greater sorption capacity was recommended for treatment of LRW to remove cesium [ru

Method of decomposing treatment for radioactive organic phosphate wastes

International Nuclear Information System (INIS)

Uki, Kazuo; Ichihashi, Toshio; Hasegawa, Akira; Sato, Tatsuaki

1985-01-01

Purpose: To decompose the organic phosphoric-acid ester wastes containing radioactive material, which is produced from spent fuel reprocessing facilities, into inorganic materials using a simple device, under moderate conditions and at high decomposing ratio. Method: Radioactive organic phosphate wates are oxidatively decomposed by H 2 O 2 in an aqueous phosphoric-acid solution of metal phosphate salts. Copper phosphates are used as the metal phosphate salts and the decomposed solution of the radioactive organic phosphate wastes is used as the aqueous solution of the copper phosphate. The temperature used for the oxidizing decomposition ranges from 80 to 100 0 C. (Ikeda, J.)

Monte Carlo Simulations of Phosphate Polyhedron Connectivity in Glasses

Energy Technology Data Exchange (ETDEWEB)

ALAM,TODD M.

1999-12-21

Monte Carlo simulations of phosphate tetrahedron connectivity distributions in alkali and alkaline earth phosphate glasses are reported. By utilizing a discrete bond model, the distribution of next-nearest neighbor connectivities between phosphate polyhedron for random, alternating and clustering bonding scenarios was evaluated as a function of the relative bond energy difference. The simulated distributions are compared to experimentally observed connectivities reported for solid-state two-dimensional exchange and double-quantum NMR experiments of phosphate glasses. These Monte Carlo simulations demonstrate that the polyhedron connectivity is best described by a random distribution in lithium phosphate and calcium phosphate glasses.

Synchrotron Photoionization Investigation of the Oxidation of Ethyl tert-Butyl Ether.

Science.gov (United States)

Winfough, Matthew; Yao, Rong; Ng, Martin; Catani, Katherine; Meloni, Giovanni

2017-02-23

The oxidation of ethyl tert-butyl ether (ETBE), a widely used fuel oxygenated additive, is investigated using Cl atoms as initiators in the presence of oxygen. The reaction is carried out at 293, 550, and 700 K. Reaction products are probed by a multiplexed chemical kinetics photoionization mass spectrometer coupled with the synchrotron radiation produced at the Advanced Light Source (ALS) of the Lawrence Berkeley National Laboratory. Products are identified on the basis of mass-to-charge ratio, ionization energies, and shape of photoionization spectra. Reaction pathways are proposed together with detected primary products.

High Solid Contents Copoly (Styrene/Butyl Acrylate-Cloisite 30B Nanocomposites

Directory of Open Access Journals (Sweden)

M. Mirzataheri

2013-03-01

Full Text Available Higher solid contents (20 % and 40 % nanocomposites of poly (styrene-co-butyl acrylate including higher content of Cloisite 30B (7 wt% and 10 wt % were prepared via miniemulsion polymerization. Stability of the final latexes proved outstanding combination of polymerization procedure and surfactants. Morphological studies revealed by TEM, SAX and XRD showed three structures of core-shell, armored and individual dispersion of clay layers within the polymer particles. The effect of Cloisite 30B content on the barrier properties presents excellent and wide use of these films for packaging and nanocoatings industries.

(N-Benzyl-N-ethyl-dithio-carbamato)di-tert-butyl-chloridotin(IV).

Science.gov (United States)

Abdul Muthalib, Amirah Faizah; Baba, Ibrahim; Mohamed Tahir, Mohamed Ibrahim; Tiekink, Edward R T

2011-02-26

The Sn(IV) atom in the title diorganotin dithio-carbamate, [Sn(C(4)H(9))(2)Cl(C(10)H(12)NS(2))], is penta-coordinated by an asymmetrically coordinating dithio-carbamate ligand, a Cl and two C atoms of the Sn-bound tert-butyl groups. The resulting C(2)ClS(2) donor set defines a coordination geometry inter-mediate between square pyramidal and trigonal bipyramidal with a slight tendency towards the former. In the crystal structure, C-H⋯π contacts link centrosymmetrically related mol-ecules into dimeric aggregates.

When does the fluazifop-P-butyl degradate, TFMP, leach through an agricultural loamy soil to groundwater?

DEFF Research Database (Denmark)

Vendelboe, Anders Lindblad; Norgaard, Trine; Olsen, Preben

2016-01-01

In intensely cultivated regions, it is crucial to have knowledge of the leaching potential related to pesticides in agricultural production. This is especially true in countries, like Denmark, that base its drinking water supply on untreated groundwater. Since fluazifop-P-butyl (FPB) is applied...

The effect of different phosphate ion concentrations and ph of the phosphate buffer on lipase bioproduction by rhizopus oligosporus

International Nuclear Information System (INIS)

Haq, I.; Ali, S.; Awan, U.F.; Javed, W.; Mirza, S.

2005-01-01

In the present investigation, we report the effect of phosphate ion concentration and different ph of the phosphate buffer (as diluent) on lipase bioproduction by Rhizopus oligosporus. For this purpose, solid state fermentation was employed. Different agricultural by-products such as wheat bran, rice husk, almond meal, soybean meal and sunflower meal were used as substrate. The maximum lipase activity (72.60 U/g) was observed with the almond meal. Addition of phosphate ions (K/sub 2/HPO/sub 4/) influenced the lipase production. The ph of the phosphate buffer (7.0) was found to be effective for higher yield of lipase. (author)

ATOM TRANSFER RADICAL POLYMERIZATION OF N-BUTYL METHACRYLATE IN AQUEOUS DISPERSED SYSTEMS: A MINIEMULSION APPROACH. (R826735)

Science.gov (United States)

Ultrasonication was applied in combination with a hydrophobe for the copper-mediated atom transfer radical polymerization of n-butyl methacrylate in an aqueous dispersed system. A controlled polymerization was successfully achieved, as demonstrated by a linear correlation between...

1-[(E-2-(5-tert-Butyl-2-hydroxyphenyldiazen-1-yl]naphthalen-2-ol

Directory of Open Access Journals (Sweden)

Hassiba Bougueria

2014-02-01

Full Text Available The non-H atoms of the title compound, C20H20N2O2, is located on a mirror plane except two methyl groups of the tert-butyl group. Intramolecular N—H...O hydrogen bonds exist between the hydroxy and diazenyl groups. In the crystal, molecules are linked by weak C—H...O hydrogen bonds into supramolecular chains running along the a-axis direction.

Pulse radiolysis study of reactions of alkyl and alkylperoxy radicals originating from methyl tert-butyl ether in the gas phase

DEFF Research Database (Denmark)

Langer, S.; Ljungström, E.; Ellermann, T.

1995-01-01

UV spectra and kinetics for the reactions of alkyl and alkylperoxy radicals from methyl tert-butyl ether (MTBE) were studied in 1 atm of SF6 by the pulse radiolysis-UV absorption technique. UV spectra for the radical mixtures were quantified from 215 to 340 nm. At 240 nm, sigma(R) = (2.6 +/- 0.4) X...... and the alkylperoxy radicals with NO and NO2 are (9.1 +/- 1.5) X 10(-13), (4.3 +/- 1.6) X 10(-12) and (1.2 +/- 0.3) X 10(-11) cm(3) molecule(-1) s(-1), respectively. The rate constants given above refer to reaction at the tert-butyl side of the molecule....

The EIS investigation of powder polyester coatings on phosphated low carbon steel: The effect of NaNO2 in the phosphating bath

International Nuclear Information System (INIS)

Jegdic, B.V.; Bajat, J.B.; Popic, J.P.; Stevanovic, S.I.; Miskovic-Stankovic, V.B.

2011-01-01

Highlights: → The effect of NaNO 2 on surface morphology of iron-phosphate coatings were determined. → Better corrosion stability of polyester coating on phosphated steel without NaNO 2 . → EIS results and microscopic examinations correlate well with adhesion measurements. - Abstract: The effect of different type of iron-phosphate coatings on corrosion stability and adhesion characteristic of top powder polyester coating on steel was investigated. Iron-phosphate coatings were deposited on steel in the novel phosphating bath with or without NaNO 2 as an accelerator. The corrosion stability of the powder polyester coating was evaluated by electrochemical impedance spectroscopy (EIS), adhesion by pull-off and NMP test, while surface morphology of phosphate coatings were investigated by atomic force microscopy (AFM). The adhesion and corrosion stability of powder polyester coatings were improved with pretreatment based on iron-phosphate coating deposited from NaNO 2 -free bath.

Radiological impact of use of phosphate fertilizers

International Nuclear Information System (INIS)

Shukla, V.K.; Chinnaesakki, S.; Sartandel, S.J.; Shanbhag, A.A.; Puranik, V.D.

2003-01-01

The paper describes the results of gamma spectrometric measurements of 238 U, 233 Th, 226 Ra and 40 K in rock phosphates and various types of phosphate fertilizers and by-products. The increase in soil natural radioactivity has been assessed for major Indian crops. No significant increase in soil natural radioactivity is expected due to the application of phosphate fertilizers for agricultural productions. (author)

Solubility of carbon dioxide in secondary butyl alcohol at high pressures : experimental and modeling with CPA

NARCIS (Netherlands)

Raeissi, S.; Haghbaksh, R.; Florusse, L.J.; Peters, C.J.

2015-01-01

Mixtures of carbon dioxide and secondary butyl alcohol at high pressures are interesting for a range of industrial applications. Therefore, it is important to have trustworthy experimental data on the high-pressure phase behavior of this mixture over a wide range of temperatures. In addition, an

Effect of Polyhedral Oligomeric Silsesquioxane (POSS) Substituents on the Rheological Behavior in Butyl Methacrylate/POSS Copolymers

Science.gov (United States)

2008-10-27

was repeated twice, dissolving the product in chloroform and diethyl ether, respectively. The polymer was dried at 60 °C under vacuum overnight...the Tg of the i Bu remains the same. Table 1. Tg for Butyl Methacrylate-co- Propyl Methacryl POSS Polymers with Various POSS Substituents

Exploring plant factors for increasing phosphorus utilization from rock phosphates and native soil phosphates in acidic soils

International Nuclear Information System (INIS)

Feng Guanglin; Xiong Liming

2002-01-01

Six plant species with contrasting capacity in utilizing rock phosphates were compared with regard to their responses to phosphorus starvation in hydroponic cultures. Radish, buckwheat and oil rapeseed are known to have strong ability to use rock phosphates while ryegrass, wheat and sesbania are less efficient. Whereas other plants acidified their culture solution under P starvation (-P), radish plants make alkaline the solution. When neutralizing the pH of the solutions cultured with plants under either -P or + P conditions, solutions with P starved buckwheat, rapeseed, and radish had a higher ability to solubilize Al and Fe phosphates than did those cultured with sesbania, ryegrass and wheat. Characterization of organic ligands in the solutions identified that citrate and malate were the major organic anions exuded by rapeseed and radish. Besides citrate and malate, buckwheat exuded a large amount of tartrate under P starvation. In contrast, ryegrass, wheat and sesbania secreted only a limited amount of oxalic acid, regardless of P status. Changes in activities of phosphoenolpyruvate carboxylase, acid phosphatase, and nitrate reductase in these plants were also compared under P- sufficient or -deficient conditions. The results indicated that plant ability to use rock phosphates or soil phosphates is closely related to their responses toward P starvation. The diversity of P starvation responses was discussed in the context of co-evolution between plants and their environment. Approaches to use plant factors to enhance the effectiveness of rock phosphates were also discussed. (author)

Thermal and thermo-mechanical behavior of butyl based rubber exposed to silicon oil at elevated temperature

International Nuclear Information System (INIS)

Ali, S.; Ramzan, S.; Raza, R.; Ahmed, F.; Hussain, R.; Ullah, S.; Ali, S.

2013-01-01

Silica reinforced rubbers are used as chemical resistant seals at high temperature. In this study the effect of alkali and silicon oil on the thermal and thermo-mechanical properties of the silica reinforced butyl rubber exposed as an interface between two liquid media at elevated temperature is investigated. Rubber bladder containing alkaline solution was immersed in silicon oil at 195+-5 degree C for multiple cycles and loss in its thermal, thermo-mechanical and mechanical properties were studied by TGA, DMA and Tinius Olsen Testing Machine supported by FTIR and Optical microscopy. It was observed that the thermal and thermo-mechanical properties of butyl rubber were negatively affected due to leaching out of silica filler embedded in an organic matrix at elevated temperature. The thermal stability of exposed rubber was decreased around 200 degree C and the loss of storage modulus was observed up to 99.5% at -59 degree C. (author)

Occurrence of organophosphate flame retardants in drinking water from China.

Science.gov (United States)

Li, Jun; Yu, Nanyang; Zhang, Beibei; Jin, Ling; Li, Meiying; Hu, Mengyang; Zhang, Xiaowei; Wei, Si; Yu, Hongxia

2014-05-01

Several organophosphate flame retardants (OPFRs) have been identified as known or suspected carcinogens or neurotoxic substances. Given the potential health risks of these compounds, we conducted a comprehensive survey of nine OPFRs in drinking water in China. We found total concentrations of OPFRs in tap water ranging from 85.1 ng/L to 325 ng/L, and tris(2-butoxyethyl) phosphate (TBEP), triphenyl phosphate (TPP), and tris(2-chloroisopropyl) phosphate (TCPP) were the most common components. Similar OPFR concentrations and profiles were observed in water samples processed through six different waterworks in Nanjing, China. However, boiling affected OPFR levels in drinking water by either increasing (e.g., TBEP) or decreasing (e.g., tributyl phosphate, TBP) concentrations depending on the particular compound and the state of the indoor environment. We also found that bottled water contained many of the same major OPFR compounds with concentrations 10-25% lower than those in tap water, although TBEP contamination in bottled water remained a concern. Finally, we concluded that the risk of ingesting OPFRs through drinking water was not a major health concern for either adults or children in China. Nevertheless, drinking water ingestion represents an important exposure pathway for OPFRs. Copyright © 2014. Published by Elsevier Ltd.

The phosphate balance : current developments and future outlook

NARCIS (Netherlands)

Enk, van R.J.; Vee, van der G.; Acera, L.K.; Schuiling, R.; Ehlert, P.A.I.

2011-01-01

Phosphate is essential for agricultural production and therefore plays a key role in the global production of food and biofuels. There are no agricultural alternatives for phosphate, and a substantial fraction of our annual phosphate consumption is dispersed into the environment where it is largely

The phosphate balance : Current developments and future outlook

NARCIS (Netherlands)

Enk, R.J. van; Acera, L.K.; Schuiling, R.D.; Ehlert, P.; de Wilt, J.G.; van Haren, R.J.F.

2011-01-01

Phosphate is essential for agricultural production and therefore plays a key role in the global production of food and biofuels. There are no agricultural alternatives for phosphate, and a substantial fraction of our annual phosphate consumption is dispersed into the environment where it is largely

Dynamics of an excess hole in the 1-methyl-1-butyl-pyrrolidinium dicyanamide ionic-liquid

Science.gov (United States)

Wu, Fei; Xu, Changhui; Margulis, Claudio J.

2018-05-01

In a set of recent publications [C. J. Margulis et al., J. Am. Chem. Soc. 133, 20186 (2011); C. H. Xu et al., J. Am. Chem. Soc. 135, 17528 (2013); C. H. Xu and C. J. Margulis, J. Phys. Chem. B 119, 532 (2015); and K. B. Dhungana et al., J. Phys. Chem. B 121, 8809 (2017)], we explored for selected ionic liquids the early stages of excess charge localization and reactivity relevant both to electrochemical and radiation chemistry processes. In particular, Xu and Margulis [J. Phys. Chem. B 119, 532 (2015)] explored the dynamics of an excess electron in 1-methyl-1-butyl-pyrrolidinium dicyanamide. When electrons are produced from an ionic liquid, the more elusive hole species are also generated. Depending on the nature of cations and anions and the relative alignment of their electronic states in the condensed phase, the very early hole species can nominally be neutral radicals—if the electron is generated from anions—or doubly charged radical cations if their origin is from cations. However, in reality early excess charge localization is more complex and often involves more than one ion. The dynamics and the transient spectroscopy of the hole are the main objects of this study. We find that in the case of 1-methyl-1-butyl-pyrrolidinium dicyanamide, it is the anions that can most easily lose an electron becoming radical species, and that hole localization is mostly on anionic nitrogen. We also find that the driving force for localization of an excess hole appears to be smaller than that for an excess electron in 1-methyl-1-butyl-pyrrolidinium dicyanamide. The early transient hole species can absorb light in the visible, ultraviolet, and near infrared regions, and we are able to identify the type of states being connected by these transitions.

The synthesis of 1-11C-labelled ethyl, propyl, butyl and isobutyl iodides and examples of alkylation reactions

International Nuclear Information System (INIS)

Laangstroem, B.; Antoni, G.; Gullberg, P.; Halldin, C.; Naagren, K.; Rimland, A.; Svaerd, H.

1986-01-01

New 11 C-labelled precursors [1- 11 C]ethyl,[1- 11 C]propyl, [1- 11 C]butyl, and [1- 11 C]isobutyl iodides have been prepared by a 3-step reaction route using a one-pot system. The labelled iodides were obtained in 20-55#percent# radiochemical yields and 65-95#percent# radiochemical purities, with a total time for synthesis of the order of 10-14 min. The labelled iodides have been used in alkylation reactions with nitrogen, oxygen and carbon nucleophiles. The nitrogen alkylation reactions are exemplified by the synthesis of the analgetics N-[1- 11 C-ethyl]iodocaine and N-[1- 11 C-butyl] bupivacaine. The synthesis of 3-nitrophenyl[1- 11 C]propyl ether is also presented in this paper as an example of an oxygen alkylation. (author)

Substituted 2,2'-bipyridines by nickel-catalysis: 4,4'-di-tert-butyl-2,2'-bipyridine.

Science.gov (United States)

Buonomo, Joseph A; Everson, Daniel A; Weix, Daniel J

2013-11-01

A simple, ligand-free synthesis of the important bipyridyl ligand 4,4'-di- tert -butyl-2,2'-bipyridine is presented. 5,5'-bis(trifluoromethyl)-2,2'-bipyridine is also synthesized by the same protocol. The syntheses efficiently couple the parent 2-chlorpyridies by a nickel-catalyzed dimerization with manganese powder as the terminal reductant.

Hyoscine-N-Butyl-Bromide-Induced Hypotension and Myocardial Ischemia

Directory of Open Access Journals (Sweden)

Guan-Liang Chen

2013-01-01

Full Text Available Hyoscine N-butyl bromide, also known as scopolamine, is a type of antimuscarinic agent. This drug is associated with numerous common side effects, including abdominal fullness, constipation, urinary retention, blurred vision, skin flushing, tachycardia, decreased sweating, and salivation. The most unfavorable side effect is hemodynamic instability. In the present case, hypotension and acute myocardial infarction developed after intravenous hyoscine injection as a premedication therapy for colonoscopy. It was difficult to differentiate the cause-effect relationship between myocardial infarction and hypotension. Because both conditions were present under drug effects, we considered 2 possible diagnoses. One was coronary spasm with cardiogenic shock, and the other was myocardial ischemic sequela due to shock status. The latter diagnosis was confirmed after a series of examinations.

Radiological impacts of uranium recovery in the phosphate industry

International Nuclear Information System (INIS)

Ryan, M.T.

1981-01-01

This article characterizes the occupational and public radiological health impacts associated with phosphate mining and milling. These impacts are related to the phosphate industry's uranium production potential and are compared with those associated with conventional uranium mining and milling. The radiological impacts resulting from occupational and nonoccupational exposures are assessed. Occupational exposures in phosphate facilities are compared to background exposures and radiological population dose assessments, which characterize important radionuclides and exposure pathways. The following conclusions were reached: (1) public consequences of phosphate mining will occur whether or not uranium is recovered as a by-product, (2) radiological consequences of phosphate mining may be comparable to those associated with uranium mining and milling per unit uranium production, (3) radiological impacts via surface waterways and crops fertilized with uranium-bearing phosphates are of minor consequence, and (4) major radiological public health problems associated with phosphate mining are related to radon and radon progeny exposures in structures built on reclaimed lands or with phosphate mining residues, although the magnitudes of these impacts are difficult to evaluate with current data

SIRT1 exhibits antioxidative effects in HT22 cells induced by tert-butyl alcohol.

Science.gov (United States)

Ma, Junxiang; Song, Dongmei; Zhang, Yuanyuan; Chen, Li; Zhang, Shixuan; Jia, Jiaxin; Chen, Tian; Guo, Caixia; Tian, Lin; Gao, Ai; Niu, Piye

2018-02-01

Tertiary butyl alcohol (TBA) is a principal metabolite of methyl tertiary-butyl ether (MTBE), a common pollutant worldwide in the ground or underground water, which is found to produce nervous system damage. Nevertheless, few data regarding the effects of TBA has been reported. Studies indicated that oxidative stress plays a pivotal role in MTBE neurotoxic mechanism. Sirtuin 1 (SIRT1) has been reported to exert a neuroprotective effect on various neurologic diseases via resistance to oxidative stress by deacetylating its substrates. In this study, we examined levels of oxidative stress after exposure to TBA for 6 h in HT22 cells and HT22 cells with SIRT1 silencing (transfected with SIRT1 siRNA) or high expression (preconditioned with agonists SRT1720). We found that TBA activated oxidative stress by increasing generation of intracellular reactive oxygen species (ROS), malondialdehyde (MDA) and Oxidized glutathione (GSSG), and decreasing contents of superoxide dismutase (SOD) and glutathione reductase (GSH). In additional, levels of TBA-induced oxidative stress were aggravated when SIRT1 silenced but alleviated when SIRT1 enhanced. Our study indicated that SIRT1 mitigated oxidative stress induced by TBA. © 2017 Wiley Periodicals, Inc.

Biodegradation of Methyl tert-Butyl Ether by Co-Metabolism with a Pseudomonas sp. Strain

Directory of Open Access Journals (Sweden)

Shanshan Li

2016-09-01

Full Text Available Co-metabolic bioremediation is supposed to be an impressive and promising approach in the elimination technology of methyl tert-butyl ether (MTBE, which was found to be a common pollutant worldwide in the ground or underground water in recent years. In this paper, bacterial strain DZ13 (which can co-metabolically degrade MTBE was isolated and named as Pseudomonas sp. DZ13 based on the result of 16S rRNA gene sequencing analysis. Strain DZ13 could grow on n-alkanes (C5-C8, accompanied with the co-metabolic degradation of MTBE. Diverse n-alkanes with different carbon number showed a significant influence on the degradation rate of MTBE and accumulation of tert-butyl alcohol (TBA. When Pseudomonas sp. DZ13 co-metabolically degraded MTBE with n-pentane as the growth substrate, a higher MTBE-degrading rate (Vmax = 38.1 nmol/min/mgprotein, Ks = 6.8 mmol/L and lower TBA-accumulation was observed. In the continuous degradation experiment, the removal efficiency of MTBE by Pseudomonas sp. Strain DZ13 did not show an obvious decrease after five times of continuous addition.

Physico-chemical characterization of Ogun and Sokoto phosphate ...

African Journals Online (AJOL)

Gypsum, calcite and lime were associated with both rock phosphates indicating their liming potential in the soil. ORP was more soluble in water, probably because it ... fertilizers and direct application in crop production. Keywords: Phosphorus, apatite, crop production, fertilizer, Ogun rock phosphate, Sokoto rock phosphate ...

Fourier transform Raman spectroscopy of synthetic and biological calcium phosphates.

Science.gov (United States)

Sauer, G R; Zunic, W B; Durig, J R; Wuthier, R E

1994-05-01

Fourier-transform (FT) Raman spectroscopy was used to characterize the organic and mineral components of biological and synthetic calcium phosphate minerals. Raman spectroscopy provides information on biological minerals that is complimentary to more widely used infrared methodologies as some infrared-inactive vibrational modes are Raman-active. The application of FT-Raman technology has, for the first time, enabled the problems of high sample fluorescence and low signal-to-noise that are inherent in calcified tissues to be overcome. Raman spectra of calcium phosphates are dominated by a very strong band near 960 cm-1 that arises from the symmetric stretching mode (v1) of the phosphate group. Other Raman-active phosphate vibrational bands are seen at approximately 1075 (v3), 590 (v4), and 435 cm-1 (v2). Minerals containing acidic phosphate groups show additional vibrational modes. The different calcium phosphate mineral phases can be distinguished from one another by the relative positions and shapes of these bands in the Raman spectra. FT-Raman spectra of nascent, nonmineralized matrix vesicles (MV) show a distinct absence of the phosphate v1 band even though these structures are rich in calcium and phosphate. Similar results were seen with milk casein and synthetic Ca-phosphatidyl-serine-PO4 complexes. Hence, the phosphate and/or acidic phosphate ions in these noncrystalline biological calcium phosphates is in a molecular environment that differs from that in synthetic amorphous calcium phosphate. In MV, the first distinct mineral phase to form contained acidic phosphate bands similar to those seen in octacalcium phosphate. The mineral phase present in fully mineralized MV was much more apatitic, resembling that found in bones and teeth.(ABSTRACT TRUNCATED AT 250 WORDS)

Development of alternate extractant systems for fast reactor fuel cycle

International Nuclear Information System (INIS)

Vasudeva Rao, P.R.; Suresh, A.; Venkatesan, K.A.; Srinivasan, T.G.; Raj, Baldev

2007-01-01

Due to the limitations of TBP in processing of high burn-up, Pu-rich fast reactor fuels, there is a need to develop alternate extractants for fast reactor fuel processing. In this context, our Centre has been examining the suitability of alternate tri-alkyl phosphates. Third phase formation in the extraction of Th(IV) by TBP, tri-n-amyl phosphate (TAP) and tri-2-methyl-butyl phosphate (T2MBP) from nitric acid media has been investigated under various conditions to derive conclusions on their application for extraction of Pu at macro levels. The chemical and radiolytic degradation of tri-n-amyl-phosphate (TAP) diluted in normal paraffin hydrocarbon (NPH) in the presence of nitric acid has been investigated by the measurement of plutonium retention in organic phase. The potential application of room temperature ionic liquids (RTILs) for reprocessing of spent nuclear fuel has been explored. Extraction of uranium (VI) and palladium (II) from nitric acid medium by commercially available RTIL and tri-n-butyl phosphate solution in RTIL have been studied and the feasibility of electrodeposition of uranium as uranium oxide (UO 2 ) and palladium (II) as metallic palladium from the loaded organic phase have been demonstrated. This paper describes results of the above studies and discusses the suitability of the systems for fast reactor fuel reprocessing. (authors)

Phosphate recycling in the phosphorus industry

NARCIS (Netherlands)

Schipper, W.J.; Klapwijk, A.; Potjer, B.; Rulkens, W.H.; Temmink, B.G.; Kiestra, F.D.G.; Lijmbach, A.C.M.

2004-01-01

The article describes the potential and limitations for recovery of phosphate from secondary materials in the production process for white phosphorus. This thermal process involves the feeding of phosphate rock, cokes and pebbles to a furnace. The reducing conditions in the furnace promote the

Portal Hypertension Secondary to Spontaneous Arterio-Portal Venous Fistulas: Transcatheter Arterial Embolization with n-Butyl Cyanoacrylate and Microcoils

International Nuclear Information System (INIS)

Yamagami, Takuji; Nakamura, Toshiyuki; Nishimura, Tsunehiko

2000-01-01

We report a 73-year-old man with recurrent variceal bleeding due to portal hypertension caused by multiple intrahepatic arterio-portal venous fistulas, which were successfully occluded by embolization with n-butyl cyanoacrylate and micro-coils

Standard characterization of phosphate rock samples from the FAO/IAEA phosphate project

International Nuclear Information System (INIS)

Binh, Truong; Zapata, F.

2002-01-01

Phosphate rocks (PR) are phosphate-bearing minerals that vary widely in their inherent characteristics and consequently their agronomic potential. In the framework of a FAO/IAEA networked research project, the evaluation of the agronomic effectiveness of natural and modified PR products under a variety of soil climate and crop management conditions was carried out. The characterization of phosphate rocks is the first and essential step in evaluating their suitability for direct application. If several PR sources are utilized, standardized methods should be used for comparison purposes to determine their agronomic potential. This paper describes the standard characterization of phosphate rock products utilized in the project, in particular the mineralogical and crystallographic analyses, physical analyses, chemical composition and solubility in conventional reagents. A total of 28 phosphate rock samples from 15 countries were collected and analyzed in specialized laboratories. The data on mineralogy, chemical composition and solubility in conventional reagents are closely interrelated. An arbitrary classification of the reactivity of the PR samples was made based on the solubility indices in conventional reagents. On another hand, the results of the crystallographic parameters, calculated indices of absolute solubility, specific surface and porosity reflect the variability of the physical state and the sample pre-conditioning treatment of the analyzed products. A proper characterization of phosphate rock samples should provide the maximum of basic information that can be obtained in a cost-effective manner in normal chemical laboratories. Based on the results of this characterization, the following determinations are recommended: a description of the sample, major elemental (total P, Ca, Mg) composition, solubility in conventional reagents (neutral ammonium citrate, citric and formic acid) and particle size analysis. The classification of PR samples for direct

Ultrasonic promoted catalyst-free N-formylation of amines in neutral ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate

Directory of Open Access Journals (Sweden)

Vinod T. Kamble

2017-05-01

Full Text Available A catalyst-free, simple and efficient protocol for N-formylation of alkyl, aryl, and heteroaryl amines with formic acid under ultrasonic irradiation at room temperature using 1-butyl-3-methylimidazolium tetrafluoroborate [Bmim]BF4 as a neutral medium is described.

Degradation of organophosphoric acid triesters by the aquatic bacteria and toxicity to fish; Yuki rinsan toriester no suichu saikin ni yoru bunkai to dokusei

Energy Technology Data Exchange (ETDEWEB)

Kawai, S. [Kobe College, Hyogo (Japan)

1996-09-10

This paper describes biodegradation of organophosphoric acid triesters (OPEs) in water environment, in particular, by aquatic bacteria. In culture experiment using river water in Osaka, aryl system OPEs such as triphenyl phosphate (TPP) and tricresyl phosphate (TCP) are more easily degraded than alkyl system OPEs, and OPEs including Cl are hardly degraded. Properties of isolated TBP degradation bacteria and enzymes, and TCP degradation bacteria isolated from Mukogawa river water are examined. OPEs are toxic to fishes equivalently to or more than organophosphoric system pesticides. However, the cause of their toxicity can`t be interpreted only by cholinesterase activity hindrance of nervous system. Absorption, accumulation, metabolism and degradation of OPEs are dependent on fishes and kinds of OPEs. Although the toxicity evaluation using experimental animals is important, the evaluation using cultured bacteria is recognizing once again from various viewpoints. Direct toxicity of OPEs to fishes or aquatic organisms is yet unidentified, however, the influence of OPEs on human beings is rather important. 39 refs., 10 figs., 2 tabs.

Dermal uptake and percutaneous penetration of organophosphate esters in a human skin ex vivo model

DEFF Research Database (Denmark)

Frederiksen, Marie; Stapleton, Heather M; Vorkamp, Katrin

2018-01-01

Organophosphate esters (OPEs) are used as flame retardants, plasticizers, and as hydraulic fluids. They are present in indoor environments in high concentrations compared with other flame retardants, and human exposure is ubiquitous. In this study we provide data for estimating dermal uptake...... through the skin. For tris(isobutyl) phosphate (TIBP), tris(n-butyl) phosphate (TNBP), and tris(methylphenyl) phosphate (TMPP) the mass balance was not stable over time indicating possible degradation during the experimental period of 72 h. The rates at which OPEs permeated through the skin decreased...

Hepatic Encephalopathy Secondary to Intrahepatic Portosystemic Venous Shunt: Balloon-Occluded Retrograde Transvenous Embolization with n-Butyl Cyanoacrylate and Microcoils

International Nuclear Information System (INIS)

Yamagami, Takuji; Nakamura, Toshiyuki; Iida, Shigeharu; Kato, Takeharu; Tanaka, Osamu; Matsushima, Shigenori; Ito, Hirotoshi; Okuyama, Chio; Ushijima, Yo; Shiga, Kensuke; Nishimura, Tsunehiko

2002-01-01

We report a 70-year-old woman with hepatic encephalopathy due to an intrahepatic portosystemic venous shunt that was successfully occluded by percutaneous transcatheter embolization with n-butyl cyanoacrylate and microcoils

Sulfuric acid functional zirconium (or aluminum) incorporated mesoporous MCM-48 solid acid catalysts for alkylation of phenol with tert-butyl alcohol

Energy Technology Data Exchange (ETDEWEB)

Jiang, Tingshun, E-mail: tshjiang@mail.ujs.edu.cn; Cheng, Jinlian; Liu, Wangping; Fu, Lie; Zhou, Xuping; Zhao, Qian; Yin, Hengbo

2014-10-15

Several zirconium (or aluminum) incorporated mesoporous MCM-48 solid acid catalysts (SO{sub 4}{sup 2−}/Zr-MCM-48 and SO{sub 4}{sup 2−}/Al-MCM-48) were prepared by the impregnation method and their physicochemical properties were characterized by means of XRD, FT-IR, TEM, NH{sub 3}-TPD and N{sub 2} physical adsorption. Also, the catalytic activities of these solid acid catalysts were evaluated by the alkylation of phenol with tert-butyl alcohol. The effect of weight hour space velocity (WHSV), reaction time and reaction temperature on catalytic properties was also studied. The results show that the SO{sub 4}{sup 2−}/Zr-MCM-48 and SO{sub 4}{sup 2−}/Al-MCM-48 still have good mesoporous structure and long range ordering. Compared with the Zr (or Al)–MCM-48 samples, SO{sub 4}{sup 2−}/Zr-MCM-48 and SO{sub 4}{sup 2−}/Al-MCM-48 solid acid catalysts have strong acidity and exhibit high activities in alkylation reaction of phenol with tert-butyl alcohol. The SO{sub 4}{sup 2−}/Zr-MCM-48-25 (molar ratio of Si/Zr=0.04) catalyst was found to be the most promising and gave the highest phenol conversion among all catalysts. A maximum phenol conversion of 91.6% with 4-tert-butyl phenol (4-TBP) selectivity of 81.8% was achieved when the molar ratio of tert-butyl alcohol:phenol is 2:1, reaction time is 2 h, the WHSV is 2 h{sup −1} and the reaction temperature is 140 °C. - Highlights: • Sulfuric acid functional mesoporous solid acid catalysts were prepared via impregnation method. • The alkylation of phenol with tert-butyl alcohol was carried out over these solid acid catalysts. • The catalytic activity of SO{sub 4}{sup 2−}/Zr-MCM-48-25 catalyst is much higher than that of the others. • A maximum phenol conversion of 91.6% was achieved under optimum reaction conditions for SO{sub 4}{sup 2−}/Zr-MCM-48-25.

Radio phosphorus kinetics in the blood of sheep supplemented with dicalcium phosphate, mono ammonium phosphate, triple superphosphate and Tapira rock phosphate

International Nuclear Information System (INIS)

Abdalla, A.L.

1992-01-01

With the aim to study the kinetics of radio phosphorus ( 32 P) in the blood of animals supplemented with dicalcium phosphate (BIC), mono ammonium phosphate (MAP), triple superphosphate (SPT) and Tapira rock phosphate (TAP), 32 male sheep were kept in metabolic cages at the Animal Science Section / CENA - USP. Plasma was obtained by centrifugation and the specific activity, rate of disappearance and half life of 32 P in plasma were determined. In the red blood cells were determined the uptake rate of the radioisotope, the rate of disappearance and half life of 32 P up taken. It was observed a statistical significant difference (p 32 P in the plasma and erythrocytes. The specific activity and half life of 32 P in the plasma were statistically different (p<0,10) among sheep receiving the different phosphorus sources; the same was observed in respect to the red blood cells. It was concluded that the supplemented phosphorus source given in the diet of sheep may affect the kinetics of the radio phosphorus in the blood after been intravenously injected. (author)

Overexpression, crystallization and preliminary X-ray analysis of xylulose-5-phosphate/fructose-6-phosphate phosphoketolase from Bifidobacterium breve

International Nuclear Information System (INIS)

Suzuki, Ryuichiro; Kim, Byung-Jun; Shibata, Tsuyoshi; Iwamoto, Yuki; Katayama, Takane; Ashida, Hisashi; Wakagi, Takayoshi; Shoun, Hirofumi; Fushinobu, Shinya; Yamamoto, Kenji

2010-01-01

Xylulose-5-phosphate/fructose-6-phosphate phosphoketolase from B. breve was overexpressed and crystallized. The crystals belonged to the tetragonal space group I422 and diffracted to beyond 1.7 Å resolution. The xylulose-5-phosphate/fructose-6-phosphate phosphoketolase gene from Bifidobacterium breve was cloned and overexpressed in Escherichia coli. The enzyme was purified to homogeneity and crystallized by the sitting-drop vapour-diffusion method. Crystals were obtained at 293 K using 0.05 mM thiamine diphosphate, 0.25 mM MgCl 2 , 24%(w/v) PEG 6000 and 0.1 M Bicine pH 9.0. The crystals belonged to the tetragonal space group I422, with unit-cell parameters a = b = 174.8, c = 163.8 Å, and diffracted to beyond 1.7 Å resolution

Vanadate influence on metabolism of sugar phosphates in fungus Phycomyces blakesleeanus.

Directory of Open Access Journals (Sweden)

Milan Žižić

Full Text Available The biological and chemical basis of vanadium action in fungi is relatively poorly understood. In the present study, we investigate the influence of vanadate (V5+ on phosphate metabolism of Phycomyces blakesleeanus. Addition of V5+ caused increase of sugar phosphates signal intensities in 31P NMR spectra in vivo. HPLC analysis of mycelial phosphate extracts demonstrated increased concentrations of glucose 6 phosphate, fructose 6 phosphate, fructose 1, 6 phosphate and glucose 1 phosphate after V5+ treatment. Influence of V5+ on the levels of fructose 2, 6 phosphate, glucosamine 6 phosphate and glucose 1, 6 phosphate (HPLC, and polyphosphates, UDPG and ATP (31P NMR was also established. Increase of sugar phosphates content was not observed after addition of vanadyl (V4+, indicating that only vanadate influences its metabolism. Obtained results from in vivo experiments indicate catalytic/inhibitory vanadate action on enzymes involved in reactions of glycolysis and glycogenesis i.e., phosphoglucomutase, phosphofructokinase and glycogen phosphorylase in filamentous fungi.

Thermochemical studies on two alkyl-bulky substituted xanthene derivatives: 9,9-dimethylxanthene and 2,7-di-tert-butyl-9,9-dimethylxanthene

International Nuclear Information System (INIS)

Freitas, Vera L.S.; Gomes, José R.B.; Ribeiro da Silva, Maria D.M.C.

2017-01-01

Highlights: • Energetic characterization of two alkyl-bulky substituted xanthene derivatives. • Massic energies of combustion of xanthene derivatives. • Enthalpies of sublimation determined by vacuum drop microcalorimetry technique. • Temperature-vapour pressure dependence by mass-loss Knudsen effusion method. • Gas-phase enthalpies of formation of alkyl xanthene derivatives. - Abstract: Thermodynamic properties of 9,9-dimethylxanthene and 2,7-di-tert-butyl-9,9-dimethylxanthene for the condensed and gas states were derived from experimental and computational studies. Static-bomb combustion calorimetry, vacuum drop microcalorimetry and the Knudsen effusion techniques were used. Computational calculations of the enthalpies of hypothetical reactions in the gaseous phase, using the G3(MP2)//B3LYP composite method, were performed for the two xanthene derivatives. Natural bond orbital (NBO) calculations were also performed to ascertain the structure and reactivity of these compounds. The energetic effects caused by replacing hydrogen atoms in the xanthene moiety by methyl and tert-butyl groups yielding 9,9-dimethylxanthene and 2,7-di-tert-butyl-9,9-dimethylxanthene species were determined from direct comparison of their standard (p o = 0.1 MPa) molar enthalpies of formation in the gaseous phase, at T = 298.15 K.

Issues of natural radioactivity in phosphates

International Nuclear Information System (INIS)

Schnug, E.; Haneklaus, S.; Schnier, C.; Scholten, L.C.

1996-01-01

The fertilization of phosphorus (P) fertilizers is essential in agricultural production, but phosphates contain in dependence on their origin different amounts of trace elements. The problem of cadmium (Cd) loads and other heavy metals is well known. However, only a limited number of investigations examined the contamination of phosphates with the two heaviest metals, uranium (U) and thorium (Th), which are radioactive. Also potassium (K) is lightly radioactive. Measurements are done n the radioactivity content of phosphates, P fertilizers and soils. The radiation doses to workers and public as well as possible contamination of soils from phosphate rock or fertilizer caused by these elements or their daughter products is of interest with regard to radiation protection. The use of P fertilizers is necessary for a sustainable agriculture, but it involves radioactive contamination of soils. The consequences of the use of P fertilizers is discussed, also with regard to existing and proposed legislation. 11 refs., 2 figs., 7 tabs

A phosphate-starvation-inducible outermembrane protein of Pseudomonas fluorescens Ag1 as an immunological phosphate-starvation marker

DEFF Research Database (Denmark)

Leopold, Kristine; Jacobsen, Susanne; Nybroe, Ole

1997-01-01

A phosphate-starvation-inducible outer-membrane protein of Pseudomonas fluorescens Ag1, expressed at phosphate concentrations below0.08-0.13 mM, was purified and characterized. The purification method involved separation of outer-membrane proteins by SDS-PAGE andextraction of the protein from...... nitrocellulose or PVDF membranes after electrotransfer of proteins to the membranes. The N-terminal amino acidsequence of the purified protein, called Psi1, did not show homology to any known proteins, and in contrast to the phosphate-specific porin OprP ofP. aeruginosa its mobility in SDS-PAGE was not affected...

Voltammetric Determination of Nitro Derivative of Synthetic Antioxidant 2,6-di-tert-butyl-4-methyl-phenol

Czech Academy of Sciences Publication Activity Database

Chýlková, J.; Machalický, O.; Tomášková, M.; Šelešovská, R.; Navrátil, Tomáš

2016-01-01

Roč. 49, č. 1 (2016), s. 92-106 ISSN 0003-2719 R&D Projects: GA ČR(CZ) GAP208/12/1645 Institutional support: RVO:61388955 Keywords : 2,6-di-tert-butyl-4-methyl-phenol * handing drop mercury electrode * nitration Subject RIV: CG - Electrochemistry Impact factor: 1.150, year: 2016

In situ NMR and modeling studies of nitroxide mediated copolymerization of styrene and n-butyl acrylate

NARCIS (Netherlands)

Hlalele, L.; Klumperman, L.

2011-01-01

The combination of in situ1H NMR and in situ31P NMR was used to study the nitroxide mediated copolymerization of styrene and n-butyl acrylate. The alkoxyamine MAMA-DEPN was employed to initiate and mediate the copolymerization. The nature of the ultimate/terminal monomer units of dormant polymer

Isolation of phosphate solubiliser fungi from Araza rhizosphere

International Nuclear Information System (INIS)

Vera, Diana Fernanda; Perez, Hernando; Valencia Hernando

2002-01-01

Araza is an eatable plant, original from the Amazon region, which has been described as a promising species for commercialization (Quevedo 1995). This plant has high productivity even in low content phosphate soil but the presence of phosphate solubilizing microorganisms may contribute to increase this element availability. In this study we report the isolation and characterization of solubilizing fungi processed using the soil washing method, from soil samples were araza is cultivated at two regions in Guaviare, Colombia. Eighteen isolates of fungi capable of solubilizing phosphate were obtained from 2 different sources. The most important species that solubilized phosphate from calcium were Trichoderma aureoviride, Aspergillus aculeatus, Trichoderma strain 1 y Trichoderma strain 2 and for phosphate from iron: Aspergillus oryzae, Paecilomyces strain 3, Gongronella butleri and Fusarium oxysporum

Dielectric aluminium phosphate thin films. Couches minces dielectriques de phosphate d'aluminium

Energy Technology Data Exchange (ETDEWEB)

Daviero, S. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Avinens, C. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Ibanez, A. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France)); Giuntini, J.C. (Lab. Physicochimie des Materiaux Solides, 34 -Montpellier (France)); Philippot, E. (Lab. Physicochimie des Materiaux Solides, 34 - Montpellier (France))

1993-04-01

Aluminium phosphate thin films on silicium substrate have been carried out from tributylphosphate and aluminium acetylacetonate precursors in solution through the ''pyrosol'' process. It can be observed a large range of chemical analysis in terms of experimental conditions. These thin films have been characterized by X-ray diffraction and infrared spectrometry. Their electrical characteristics, defined from direct current and alternative current measurements, are quite different to those of the crystallized phosphate and can be explained by P-O and Al-O ''dangling bond'' existence. (orig.).

Phosphate recycling in the phosphorus industry

NARCIS (Netherlands)

Schipper, W.J.; Klapwijk, A.; Potjer, A.; Rulkens, W.H.; Temmink, B.G.; Kiestra, F.D.G.; Lijmbach, A.C.M.

2001-01-01

The feasibility of phosphate recycling in the white phosphorus production process is discussed. Several types of materials may be recycled, provided they are dry inorganic materials, low in iron, copper and zinc. Sewage sludge ash may be used if no iron is used for phosphate precipitation in the

Application of Potential Phosphate-Solubilizing Bacteria and Organic Acids on Phosphate Solubilization from Phosphate Rock in Aerobic Rice

Directory of Open Access Journals (Sweden)

Qurban Ali Panhwar

2013-01-01

Full Text Available A study was conducted at Universiti Putra Malaysia to determine the effect of phosphate-solubilizing bacteria (PSB and organic acids (oxalic & malic on phosphate (P solubilization from phosphate rock (PR and growth of aerobic rice. Four rates of each organic acid (0, 10, 20, and 30 mM, and PSB strain (Bacillus sp. were applied to aerobic rice. Total bacterial populations, amount of P solubilization, P uptake, soil pH, and root morphology were determined. The results of the study showed significantly high P solubilization in PSB with organic acid treatments. Among the two organic acids, oxalic acid was found more effective compared to malic acid. Application of oxalic acid at 20 mM along with PSB16 significantly increased soluble soil P (28.39 mg kg−1, plant P uptake (0.78 P pot−1, and plant biomass (33.26 mg. Addition of organic acids with PSB and PR had no influence on soil pH during the planting period. A higher bacterial population was found in rhizosphere (8.78 log10 cfu g−1 compared to the nonrhizosphere and endosphere regions. The application of organic acids along with PSB enhanced soluble P in the soil solution, improved root growth, and increased plant biomass of aerobic rice seedlings without affecting soil pH.

Effectiveness and cost-efficiency of phosphate binders in hemodialysis

Directory of Open Access Journals (Sweden)

Zsifkovits, Johannes

2009-06-01

Full Text Available Health political background: In 2006, the prevalence of chronic renal insufficiency in Germany was 91,718, of which 66,508 patients were on dialysis. The tendency is clearly growing. Scientific background: Chronic renal insufficiency results in a disturbance of the mineral balance. It leads to hyperphosphataemia, which is the strongest independent risk factor for mortality in renal patients. Usually, a reduction in the phosphate intake through nutrition and the amount of phosphate filtered out during dialysis are not sufficient to reduce the serum phosphate values to the recommended value. Therefore, phosphate binders are used to bind ingested phosphate in the digestive tract in order to lower the phosphate concentration in the serum. Four different groups of phosphate binders are available: calcium- and aluminium salts are the traditional therapies. Sevelamer and Lanthanum are recent developments on the market. In varying doses, all phosphate binders are able to effectively lower phosphate concentrations. However, drug therapies have achieved recommended phosphate levels in only 50 percent of patients during the last years. Research questions: How effective and efficient are the different phosphate binders in chronic renal insufficient patients? Methods: The systematic literature search yielded 1,251 abstracts. Following a two-part selection process with predefined criteria 18 publications were included in the assessment. Results: All studies evaluated conclude that serum phosphate, serum calcium and intact parathyroid hormone can be controlled effectively with all phosphate binders. Only the number of episodes of hypercalcaemia is higher when using calcium-containing phosphatebinders compared to Sevelamer and Lanthanum. Regarding the mortality rate, the cardiovascular artery calcification and bone metabolism no definite conclusions can be drawn. In any case, the amount of calcification at study start seems to be crucial for the further

Interaction of butylated hydroxyanisole with mitochondrial oxidative phosphorylation.

Science.gov (United States)

Fusi, F; Sgaragli, G; Murphy, M P

1992-03-17

The antioxidant, butylated hydroxyanisole (BHA), has a number of effects on mitochondrial oxidative phosphorylation. In this study we apply the novel approach developed by Brand (Brand MD, Biochim Biophys Acta 1018: 128-133, 1990) to investigate the site of action of BHA on oxidative phosphorylation in rat liver mitochondria. Using this approach we show that BHA increases the proton leak through the mitochondrial inner membrane and that it also inhibits the delta p (proton motive force across the mitochondrial inner membrane) generating system, but has no effect on the phosphorylation system. This demonstrates that compounds having pleiotypic effects on mitochondrial oxidative phosphorylation in vitro can be analysed and their many effects distinguished. This approach is of general use in analysing many other compounds of pharmacological interest which interact with mitochondria. The implications of these results for the mechanism of interaction of BHA with mitochondrial oxidative phosphorylation are discussed.

Phosphate Framework Electrode Materials for Sodium Ion Batteries.

Science.gov (United States)

Fang, Yongjin; Zhang, Jiexin; Xiao, Lifen; Ai, Xinping; Cao, Yuliang; Yang, Hanxi

2017-05-01

Sodium ion batteries (SIBs) have been considered as a promising alternative for the next generation of electric storage systems due to their similar electrochemistry to Li-ion batteries and the low cost of sodium resources. Exploring appropriate electrode materials with decent electrochemical performance is the key issue for development of sodium ion batteries. Due to the high structural stability, facile reaction mechanism and rich structural diversity, phosphate framework materials have attracted increasing attention as promising electrode materials for sodium ion batteries. Herein, we review the latest advances and progresses in the exploration of phosphate framework materials especially related to single-phosphates, pyrophosphates and mixed-phosphates. We provide the detailed and comprehensive understanding of structure-composition-performance relationship of materials and try to show the advantages and disadvantages of the materials for use in SIBs. In addition, some new perspectives about phosphate framework materials for SIBs are also discussed. Phosphate framework materials will be a competitive and attractive choice for use as electrodes in the next-generation of energy storage devices.

Synthesis of 1-/sup 11/C-labelled ethyl, propyl, butyl and isobutyl iodides and examples of alkylation reactions

Energy Technology Data Exchange (ETDEWEB)

Laangstroem, B.; Antoni, G.; Gullberg, P.; Halldin, C.; Naagren, K.; Rimland, A.; Svaerd, H.

1986-01-01

New /sup 11/C-labelled precursors (1-/sup 11/C)ethyl,(1-/sup 11/C)propyl, (1-/sup 11/C)butyl, and (1-/sup 11/C)isobutyl iodides have been prepared by a 3-step reaction route using a one-pot system. The labelled iodides were obtained in 20-55% radiochemical yields and 65-95% radiochemical purities, with a total time for synthesis of the order of 10-14 min. The labelled iodides have been used in alkylation reactions with nitrogen, oxygen and carbon nucleophiles. The nitrogen alkylation reactions are exemplified by the synthesis of the analgetics N-(1-/sup 11/C-ethyl)iodocaine and N-(1-/sup 11/C-butyl) bupivacaine. The synthesis of 3-nitrophenyl(1-/sup 11/C)propyl ether is also presented in this paper as an example of an oxygen alkylation.

Photoelectron spectroscopy of phosphites and phosphates

Energy Technology Data Exchange (ETDEWEB)

Chattopadhyay, S.; Findley, G.L.; McGlynn, S.P.

1981-01-01

The ultraviolet photoelectron spectra (UPS) of trimethyl and triethyl phosphite, trimethyl and triethyl phosphate and four substituted phosphates are presented. Assignments are based on analogies to the UPS of phosphorus trichloride and phosphoryl trichloride and are substantiated by CNDO/2 computations. The mechanisms of P-O (axial) bond formation is discussed.

An indirect method for determining phosphorus in aluminium alloys by atomic-absorption spectrometry.

Science.gov (United States)

Bernal, J L; Del Nozal, M A; Deban, L; Aller, A J

1981-07-01

An indirect method is described for the determination of phosphorus in aluminium alloys. Ammonium molybdate is added to a solution of the aluminium alloy and the molybdophosphoric acid formed is selectively extracted into n-butyl acetate. The twelve molybdenum atoms associated with each phosphate ion are determined by direct atomic-absorption spectrometry with the n-butyl acetate phase in a nitrous oxide-acetylene flame, with measurement at 313.2 nm. The most suitable conditions have been established and the effect of other ions has been studied.

Phosphate uptake kinetics for four species of submerged freshwater macrophytes measured by a 33P phosphate radioisotope technique

DEFF Research Database (Denmark)

Christiansen, Nina Høj; Andersen, Frede Østergaard; Jensen, Henning S.

2016-01-01

Phosphate (Pi) uptake kinetics were determined in shoot and root tissues for four freshwater macrophyte species, Littorella uniflora, Potamogeton perfoliatus, Myriophyllum alterniflorum and Elodea canadensis, using a radioactive 33P phosphate technique. Collection of plant material in the oligotr...

The variable charge of andisols as affected by nanoparticles of rock phosphate and phosphate solubilizing bacteria

Science.gov (United States)

Arifin, M.; Nurlaeny, N.; Devnita, R.; Fitriatin, B. N.; Sandrawati, A.; Supriatna, Y.

2018-02-01

Andisols has a great potential as agriculture land, however, it has a high phosphorus retention, variable charge characteristics and high value of zero net charge or pH0. The research is aimed to study the effects of nanoparticles of rock phosphate (NPRP) and biofertilizer (phosphate solubilizing bacteria/PSB) on soil pH, pHo (zero point of charge, ZPC) and organic-C in one subgroup of Andisols, namely Acrudoxic Durudands, Ciater Region West Java. The research was conducted from October 2016 to February 2017 in Soil Physics Laboratory and Laboratory of Soil Chemistry and Fertility, Soil Science Department, Faculty of Agriculture, Universitas Padjadjaran. This experiment used a completely randomized factorial design, consisting of two factors and three replications. The first factor was nanoparticles of rock phosphate consist of 4 doses 0; 25; 50 and 75 g/1 kg soil and the second factor was biofertilizer dose consist of g/1 kg soil and without biofertilizer. Total treatment combinations were 8 with 3 replications, so there were 24 experimental plots. The results showed that in general NPRR and biofertilizer will decrease the value of soil pH throughout the incubation periods. There is an interaction between nanoparticles of rock phosphate and biofertilizer in decreasing pHo in the first month of incubation, but after 4-month incubation period, NPRP increased. Interaction between 75 g nanoparticles of rock phosphate with 1 g biofertilizer/1 kg soil in fourth months of incubation decreased soil organic-C to 3.35%.

Uranium and heavy metals in phosphate fertilizers

International Nuclear Information System (INIS)

Khater, A.E.M.

2008-01-01

Agricultural applications of chemical fertilizers are a worldwide practice. The specific activity of uranium-238 and heavy metals in phosphate fertilizers depends on the phosphate ore from which the fertilizer produced and on the chemical processing of the ore. Composite phosphate fertilizers samples where collected and the uranium-238 specific activity, in Bq/kg, and As, Cd, Cu, Pb, Se concentration, in ppm, were measured. The annual addition of these elements in soil due to fertilization were calculated and discussed. (author)(tk)

Uranium and heavy metals in phosphate fertilizers

International Nuclear Information System (INIS)

Khater, Ashraf E.M.; King Saud University, Riyadh

2008-01-01

Full text: Agricultural applications of chemical fertilizers are a worldwide practice. The specific activity of uranium-238 and heavy metals in phosphate fertilizers depends on the phosphate ore from which the fertilizer produced and on the chemical processing of the ore. Composite phosphate fertilizers samples were collected and the uranium-238 specific activity, in Bq/kg, and As, Cd, Cu, Pb, Se concentration were measured. The annual addition of these elements in soil due to soil fertilization were calculated and discussed. (author)

Availability of native and added phosphates for the soil

International Nuclear Information System (INIS)

Scivittaro, W.B.; Boaretto, A.E.; Muraoka, T.

1995-01-01

In superficial composite samples of two Red-Yellow Latosols with different physical and chemical properties, analyses were carried out on inorganic form of phosphorus as well as the availability of native and added phosphates. The method applied was soil phosphorus fractionation associated with isotopic dilution technique ( 32 P). The samples were taken from pots containing soils incubated for a month with fluid phosphatic fertilizers (phosphoric acid and 10-30-00 suspension) and solid phosphatic fertilizers (mono ammonium phosphate and triple superphosphate), at the rate of 210 mg P 2 O 5 /kg of soil. A control treatment was included. In both soils the availability of inorganic phosphorus fractions decreased at the following order: H 2 O-P > Al-P > Fe-P > CA-P > occluded-P. The water soluble and aluminium phosphates represented the main source of available P for the newly fertilizer, the iron phosphates were also an important source of available phosphorus. The soil phosphorus fixing capacity influenced the availability of native and added phosphates. (author). 17 refs, 3 tabs

Developmental and testicular toxicity of butyl benzyl phthalate in the rat and the impact of study design

NARCIS (Netherlands)

Piersma AH; Verhoef A; Dormans JAMA; Elvers LH; Valk V de; Biesebeek JD te; Pieters MN; Slob W; LEO

1999-01-01

The developmental toxicity of butyl benzyl phthalate was investigated in the rat in an alternative study design using ten treatment groups. The effect of exposure period was studied, and a comparison of reaction to treatment in pregnant versus non-pregnant females was made. The classical data

Regularities in Low-Temperature Phosphatization of Silicates

Science.gov (United States)

Savenko, A. V.

2018-01-01

The regularities in low-temperature phosphatization of silicates are defined from long-term experiments on the interaction between different silicate minerals and phosphate-bearing solutions in a wide range of medium acidity. It is shown that the parameters of the reaction of phosphatization of hornblende, orthoclase, and labradorite have the same values as for clayey minerals (kaolinite and montmorillonite). This effect may appear, if phosphotization proceeds, not after silicate minerals with a different structure and composition, but after a secondary silicate phase formed upon interaction between silicates and water and stable in a certain pH range. Variation in the parameters of the reaction of phosphatization at pH ≈ 1.8 is due to the stability of the silicate phase different from that at higher pH values.

Studies on the effect of nano-TiO{sub 2} on vinyl acetate-butyl acrylate latex-based surface coating

Energy Technology Data Exchange (ETDEWEB)

Suma, K.K. [Dept. of Polymer Science and Rubber Technology, Cochin University of Science and Technology, Kochi 22, Kerala (India); Dept. of Chemistry, Maharaja' s College, Ernakulam, Kerala (India); Jacob, Sinto [Dept. of Polymer Science and Rubber Technology, Cochin University of Science and Technology, Kochi 22, Kerala (India); Joseph, Rani, E-mail: rani@cusat.ac.i [Dept. of Polymer Science and Rubber Technology, Cochin University of Science and Technology, Kochi 22, Kerala (India)

2010-04-15

Vinyl acetate-butyl acrylate (VAc-BuA) copolymer latex was prepared by emulsion polymerization. The polymerization conditions and the composition were optimized. The 85/15 wt.% (vinyl acetate/butyl acrylate) gave good tensile strength of the order of 15.6 MPa and a glass transition temperature (T{sub g}) value of -6.49 deg. C. This copolymer was used as a binder in the paint formulation. In this formulation nanosized TiO{sub 2} sol was used as a pigment instead of conventional rutile TiO{sub 2}. Nanosized TiO{sub 2} is prepared by wet process. These nanosized TiO{sub 2} rutile colloidal sol has improved properties such as photostability, UV shielding, dispersion stability, etc. The surface properties of paint were found to be superior compared to commercially used paint.

Polymeric reagents

International Nuclear Information System (INIS)

Bozkurt, C.

1979-01-01

The system polymer-bound triphenyl phosphine/carbon tetrachloride was used for preparation of 14 C-labelled organic compounds. 7- 14 C-benzyl chloride, 7- 14 C-benzoyl chloride and 7- 14 C-N-butyl benzamide have been prepared in this way. The reaction conditions were optimized using inactive compounds. Using the results of this optimization, radiochemical yields of 90% could be obtained for the first time for the preparation of 14 C-labelled alkyl chlorides and carboxylic acid chlorides from the corresponding alcohols and acids on the carrier. Polymer-bound triphenylphosphine was further studied as a catalyst for Beckmann rearrangement on the example of the rearrangement of cyclohexanoneoxime into epsilon-caprolactam. Yields exceeding 90% could be obtained with polymer-bound triphenylphosphine. However, regeneration of the catalyst could only be achieved by the already known method using trichlorosilane, in part also with methyldichlorosilane. Other reducing agents were unsuccessful in regenerating the catalyst. (G.G.)

Alpha-tocopheryl phosphate: a novel, natural form of vitamin E.

Science.gov (United States)

Gianello, Robert; Libinaki, Roksan; Azzi, Angelo; Gavin, Paul D; Negis, Yesim; Zingg, Jean-Marc; Holt, Phillip; Keah, Hooi-Hong; Griffey, Annike; Smallridge, Andrew; West, Simon M; Ogru, Esra

2005-10-01

We have detected alpha-tocopheryl phosphate in biological tissues including liver and adipose tissue, as well as in a variety of foods, suggesting a ubiquitous presence in animal and plant tissue. Alpha-tocopheryl phosphate is a water-soluble molecule that is resistant to both acid and alkaline hydrolysis, making it undetectable using standard assays for vitamin E. A new method was therefore developed to allow the extraction of both alpha-tocopheryl phosphate and alpha-tocopherol from a single specimen. We used ESMS to detect endogenous alpha-tocopheryl phosphate in biological samples that also contained alpha-tocopherol. Due to the significance of these findings, further proof was required to unequivocally demonstrate the presence of endogenous alpha-tocopheryl phosphate in biological samples. Four independent methods of analysis were examined: HPLC, LCMS, LCMS/MS, and GCMS. Alpha-tocopherol phosphate was identified in all instances by comparison between standard alpha-tocopheryl phosphate and extracts of biological tissues. The results show that alpha-tocopheryl phosphate is a natural form of vitamin E. The discovery of endogenous alpha-tocopheryl phosphate has implications for the expanding knowledge of the roles of alpha-tocopherol in biological systems.

P contribution derived from phosphate solubilizing microorganism activity, rock phosphate and SP-36 determination by isotope "3"2P technique

International Nuclear Information System (INIS)

Anggi Nico Flatian; Iswandi Anas; Atang Sutandi; Ishak

2016-01-01

The "3"2P isotope technique has been used to trace P nutrients in the soil and soil-plant systems. The use of the isotope "3"2P has made it possible to differentiate the P contribution derived from phosphate solubilizing microorganism activity and the fertilizer P in the soil. The aims of the study were to obtain the quantitative data of P contribution derived from phosphate-solubilizing microorganism activity (Aspergillus niger and Burkholderia cepacia), rock phosphate and SP-36 through P uptake by the plants using isotope "3"2P technique and also to study the effects on growth and production of corn plants. The results were showed that phosphate-solubilizing microorganism, rock phosphate and SP-36 was produced specific activity ("3"2P) lower than control. The results were indicated that all treatments could contribute P for the plants. The lower specific activity was caused by supply P from rock phosphate and SP-36, and also was caused by solubilized of unavailable "3"1P from PSM activity, which decreased specific activity on labeled soil. The combination of phosphate-solubilizing microorganism and SP-36 treatments produced the highest P contribution, significantly higher than control and SP-36 only. Phosphate derived from combination of microorganism and SP-36 treatments ranging from 56.06% - 68.54% after 50 days planting, after 35 days planting, 51.96% - 59.65% on stover, 46.33% - 47.70% on grain and 53.02% - 59.87% on corn cob. In addition, the treatments could significantly support the plant growth and yield. It is expressed by increased number of leave at 35 days after planting, dry weight of leave at 35 days after planting and dry weight of grain. (author)

The Emulsion Polymerization of Each of Vinyl Acetate and Butyl Acrylate Monomers Using bis (2-ethylhexyl Maleate for Improving the Physicomechanical Properties of Paints and Adhesive Films

Directory of Open Access Journals (Sweden)

K. A. Shaffei

2009-01-01

Full Text Available Improving the water sensitivity of polyvinyl acetate PVAc films as well as pressure sensitivity, adhesion and washability of polybutyl acrylate were achieved by using bis (2-ethylhexyl maleate (BEHM. The emulsion polymerization kinetics of vinyl acetate and butyl acrylate in presence of BEHM was studied. The order of the polymerization reaction with respect to the BEHM in presence of each of vinyl acetate and butyl acrylate was studied. The physicomechanical properties of the polyvinyl acetate films and vinyl acetate-butyl acrylate copolymer films were studied in presence of BEHM and the obtained results were matched with those prepared in the presence of pluronic F 108 and showed superior values. The obtained mean average molecular weights were found to be smaller in presence of BEHM assuring the presence of chain transfer reaction.

Structure of methylene chloride addition product to zirconium tetrachloride complex with 1-tert.-butyl-2,4,4-trimethyl-2-thio-trimethylsilyl-1,3,2,4-diazaphosphasilatedine

International Nuclear Information System (INIS)

Brusilovets, A.I.; Rusanov, Eh.B.; Chernega, A.N.

1995-01-01

Complex of zirconium tetrachloride with 1-tert.-butyl-2,4,4-trimethyl--2-thio-3-trimethyl-silyl-1,3,2,4-diazaphosphasilatedine interacts with methylene chloride with formation of bis[3-tert.-butyl-2,4,4-trimethyl-1--trimethylsilyl-2-chloremethylthio-1,3,2,4-diazaphosphasilatedinium] decachlorodizirconate. Specific features of crystal and molecular structure of the compound prepared have been studied by X-ray diffraction method. 21 refs.; 2 figs.; 2 tabs

Butylated caffeic acid: An efficient novel antioxidant; Ácido cafeico butilado: un nuevo y eficaz antioxidante.

Energy Technology Data Exchange (ETDEWEB)

Shi, G.; Liao, X.; Olajide, T.M.; Liu, J.; Jiang, X.; Weng, X.

2017-07-01

A novel antioxidant, butylated caffeic acid (BCA) was rationally designed by adding a tert-butyl group to caffeic acid, which was synthesized at a high yield (36.2%) from 2-methoxy-4-methylphenol (1) by a four-step reaction including Friedel-Crafts alkylation, bromine oxidation, ether bond hydrolysis and Knoevenagel condensation. Its antioxidant capacity was much stronger than common commercial antioxidant tert-butyl hydroquinone (TBHQ) and its mother compound, caffeic acid, in both rancimat and deep frying tests. When investigated via the DPPH method, the antioxidant capacity of BCA was almost equal to TBHQ, but lower than caffeic acid. BCA could be a potentially strong antioxidant, especially for food processing at high temperatures such as deep frying and baking. [Spanish] Se diseñó razonadamente un nuevo antioxidante, el ácido cafeico butilado (BCA) mediante la adición de un grupo terc-butilo al ácido cafeico, que se sintetizó con un alto rendimiento (36,2%) a partir de 2-metoxi-4-metilfenol, reacción de Friedel-Crafts, oxidación de bromo, hidrólisis del enlace éter y condensación de Knoevenagel. Su capacidad antioxidante fué mucho más fuerte que la del antioxidante comercial mas común el terc-butil hidroquinona (TBHQ) y la de su compuesto madre el ácido cafeico, tanto en rancimat como en pruebas de fritura. Cuando se investigó mediante el método DPPH, la capacidad antioxidante de BCA fue casi igual a TBHQ, pero menor que la del ácido cafeico. BCA podría ser un fuerte antioxidante potencial, especialmente para el procesamiento de alimentos a alta temperatura, tales como freír y hornear.

Nano zinc phosphate coatings for enhanced corrosion resistance of mild steel

International Nuclear Information System (INIS)

Tamilselvi, M.; Kamaraj, P.; Arthanareeswari, M.; Devikala, S.

2015-01-01

Highlights: • Nano zinc phosphate coating on mild steel was developed. • Nano zinc phosphate coatings on mild steel showed enhanced corrosion resistance. • The nano ZnO increases the number of nucleating sites for phosphating. • Faster attainment of steady state during nano zinc phosphating. - Abstract: Nano crystalline zinc phosphate coatings were developed on mild steel surface using nano zinc oxide particles. The chemical composition and morphology of the coatings were analyzed by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The particles size of the nano zinc phosphate coating developed was also characterized by TEM analysis. Potentiodynamic polarization and electrochemical impedance studies were carried out in 3.5% NaCl solution. Significant variations in the coating weight, morphology and corrosion resistance were observed as nano ZnO concentrations were varied from 0.25 to 2 g/L in the phosphating baths. The results showed that nano ZnO particles in the phosphating solution yielded phosphate coatings of higher coating weight, greater surface coverage and enhanced corrosion resistance than the normal zinc phosphate coatings (developed using normal ZnO particles in the phosphating baths). Better corrosion resistance was observed for coatings derived from phosphating bath containing 1.5 g/L nano ZnO. The activation effect brought about by the nano ZnO reduces the amount of accelerator (NaNO 2 ) required for phosphating

Biosynthesis of t-Butyl in Apratoxin A: Functional Analysis and Architecture of a PKS Loading Module.

Science.gov (United States)

Skiba, Meredith A; Sikkema, Andrew P; Moss, Nathan A; Lowell, Andrew N; Su, Min; Sturgis, Rebecca M; Gerwick, Lena; Gerwick, William H; Sherman, David H; Smith, Janet L

2018-04-27

The unusual feature of a t-butyl group is found in several marine-derived natural products including apratoxin A, a Sec61 inhibitor produced by the cyanobacterium Moorea bouillonii PNG 5-198. Here we determine that the apratoxin A t-butyl group is formed as pivaloyl acyl carrier protein (ACP) by AprA, the polyketide synthase (PKS) loading module of the apratoxin A biosynthetic pathway. AprA contains an inactive "pseudo" GCN5-related N-acetyltransferase domain (ΨGNAT) flanked by two methyltransferase domains (MT1 and MT2) that differ distinctly in sequence. Structural, biochemical, and precursor incorporation studies reveal that MT2 catalyzes unusually coupled decarboxylation and methylation reactions to transform dimethylmalonyl-ACP, the product of MT1, to pivaloyl-ACP. Further, pivaloyl-ACP synthesis is primed by the fatty acid synthase malonyl acyltransferase (FabD), which compensates for the ΨGNAT and provides the initial acyl-transfer step to form AprA malonyl-ACP. Additionally, images of AprA from negative stain electron microscopy reveal multiple conformations that may facilitate the individual catalytic steps of the multienzyme module.

Sensitivity of photoelectron diffraction to conformational changes of adsorbed molecules: Tetra-tert-butyl-azobenzene/Au(111

Directory of Open Access Journals (Sweden)

A. Schuler

2017-01-01

Full Text Available Electron diffraction is a standard tool to investigate the atomic structure of surfaces, interfaces, and adsorbate systems. In particular, photoelectron diffraction is a promising candidate for real-time studies of structural dynamics combining the ultimate time resolution of optical pulses and the high scattering cross-sections for electrons. In view of future time-resolved experiments from molecular layers, we studied the sensitivity of photoelectron diffraction to conformational changes of only a small fraction of molecules in a monolayer adsorbed on a metallic substrate. 3,3′,5,5′-tetra-tert-butyl-azobenzene served as test case. This molecule can be switched between two isomers, trans and cis, by absorption of ultraviolet light. X-ray photoelectron diffraction patterns were recorded from tetra-tert-butyl-azobenzene/Au(111 in thermal equilibrium at room temperature and compared to patterns taken in the photostationary state obtained by exposing the surface to radiation from a high-intensity helium discharge lamp. Difference patterns were simulated by means of multiple-scattering calculations, which allowed us to determine the fraction of molecules that underwent isomerization.

Reduction of nucleotides by ionizing radiation: uridine 5' phosphate, and cytidine 3' phosphate

International Nuclear Information System (INIS)

Box, H.C.; Potter, W.R.; Budzinski, E.E.

1974-01-01

Anions formed by the addition of an electron to the uracil base were observed in single crystals of the barium salt of uridine 5' phosphate x irradiated at 4.2 0 K. The hyperfine coupling tensor for the C 6 -H proton was deduced from ENDOR measurements; the principal values are -59.12, -32.92 and -16.24 MHz. Similar measurements were made on single crystals of cytidine 3' phosphate. The principal values for the C 6 -H proton hyperfine coupling in the anion formed on the cytosine base are -59.26, -33.98 and -14.68 MHz. (U.S.)

Combined Effects of Ultrasound and Immobilization Protocol on Butyl Acetate Synthesis Catalyzed by CALB

Directory of Open Access Journals (Sweden)

Joana S. Alves

2014-07-01

Full Text Available It is well established that the performance of lipase B from Candida antarctica (CALB as catalyst for esterification reactions may be improved by the use of ultrasound technology or by its immobilization on styrene-divinylbenzene beads (MCI-CALB. The present research evaluated the synthesis of butyl acetate using MCI-CALB under ultrasonic energy, comparing the results against those obtained using the commercial preparation, Novozym 435. The optimal conditions were determined using response surface methodology (RSM evaluating the following parameters: reaction temperature, substrate molar ratio, amount of biocatalyst, and added water. The optimal conditions for butyl acetate synthesis catalyzed by MCI-CALB were: temperature, 48.8 °C; substrate molar ratio, 3.46:1 alcohol:acid; amount of biocatalyst, 7.5%; and added water 0.28%, both as substrate mass. Under these conditions, 90% of conversion was reached in 1.5 h. In terms of operational stability, MCI-CALB was reused in seven cycles while keeping 70% of its initial activity under ultrasonic energy. The support pore size and resistance are key points for the enzyme activity and stability under mechanical stirring. The use of ultrasound improved both activity and stability because of better homogeneity and reduced mechanical stress to the immobilized system.

Magnesium-phosphate-glass cements with ceramic-type properties

Science.gov (United States)

Sugama, T.; Kukacka, L.E.

1982-09-23

Rapid setting magnesium phosphate (Mg glass) cementitious materials consisting of magnesium phosphate cement paste, polyborax and water-saturated aggregate, exhibits rapid setting and high early strength characteristics. The magnesium glass cement is prepared from a cation-leachable powder and a bivalent metallic ion-accepting liquid such as an aqueous solution of diammonium phosphate and ammonium polyphosphate. The cation-leachable powder includes a mixture of two different magnesium oxide powders processed and sized differently which when mixed with the bivalent metallic ion-accepting liquid provides the magnesium glass cement consisting primarily of magnesium ortho phosphate tetrahydrate, with magnesium hydroxide and magnesium ammonium phosphate hexahydrate also present. The polyborax serves as a set-retarder. The resulting magnesium mono- and polyphosphate cements are particularly suitable for use as a cementing matrix in rapid repair systems for deteriorated concrete structures as well as construction materials and surface coatings for fireproof structures.

Magnesium phosphate glass cements with ceramic-type properties

Science.gov (United States)

Sugama, Toshifumi; Kukacka, Lawrence E.

1984-03-13

Rapid setting magnesium phosphate (Mg glass) cementitious materials consisting of magnesium phosphate cement paste, polyborax and water-saturated aggregate exhibiting rapid setting and high early strength characteristics. The magnesium glass cement is prepared from a cation-leachable powder and a bivalent metallic ion-accepting liquid such as an aqueous solution of diammonium phosphate and ammonium polyphosphate. The cation-leachable powder includes a mixture of two different magnesium oxide powders processed and sized differently which when mixed with the bivalent metallic ion-accepting liquid provides the magnesium glass cement consisting primarily of magnesium ortho phosphate tetrahydrate, with magnesium hydroxide and magnesium ammonium phosphate hexahydrate also present. The polyborax serves as a set-retarder. The resulting magnesium mono- and polyphosphate cements are particularly suitable for use as a cementing matrix in rapid repair systems for deteriorated concrete structures as well as construction materials and surface coatings for fireproof structures.

A Phosphate Starvation-Inducible Ribonuclease of Bacillus licheniformis.

Science.gov (United States)

Nguyen, Thanh Trung; Nguyen, Minh Hung; Nguyen, Huy Thuan; Nguyen, Hoang Anh; Le, Thi Hoi; Schweder, Thomas; Jürgen, Britta

2016-08-28

The BLi03719 protein of Bacillus licheniformis DSM13 belongs to the most abundant extracellular proteins under phosphate starvation conditions. In this study, the function of this phosphate starvation inducible protein was determined. An amino-acid sequence analysis of the BLi03719-encoding gene showed a high similarity with genes encoding the barnase of Bacillus amyloliquefaciens FZB42 and binase-like RNase of Bacillus pumilus SARF-032. The comparison of the control strain and a BLi03719-deficient strain revealed a strongly reduced extracellular ribonuclease activity of the mutant. Furthermore, this knockout mutant exhibited delayed growth with yeast RNA as an alternative phosphate and carbon source. These results suggest that BLi03719 is an extracellular ribonuclease expressed in B. licheniformis under phosphate starvation conditions. Finally, a BLi03719 mutant showed an advantageous effect on the overexpression of the heterologous amyE gene under phosphate-limited growth conditions.

Facing the challenge of predicting the standard formation enthalpies of n-butyl-phosphate species with ab initio methods

Science.gov (United States)

Saab, Mohamad; Réal, Florent; Šulka, Martin; Cantrel, Laurent; Virot, François; Vallet, Valérie

2017-06-01

Tributyl-phosphate (TBP), a ligand used in the PUREX liquid-liquid separation process of spent nuclear fuel, can form an explosive mixture in contact with nitric acid that might lead to a violent explosive thermal runaway. In the context of safety of a nuclear reprocessing plant facility, it is crucial to predict the stability of TBP at elevated temperatures. So far, only the enthalpies of formation of TBP are available in the literature with rather large uncertainties, while those of its degradation products, di-(HDBP) and mono-(H2MBP), are unknown. In this goal, we have used state-of-the art quantum chemical methods to compute the formation enthalpies and entropies of TBP and its degradation products di-(HDBP) and mono-(H2MBP) in gas and liquid phases. Comparisons of levels of quantum chemical theory revealed that there are significant effects of correlation on their electronic structures, pushing for the need of not only high level of electronic correlation treatment, namely, local coupled cluster with single and double excitation operators and perturbative treatment of triple excitations, but also extrapolations to the complete basis to produce reliable and accurate thermodynamics data. Solvation enthalpies were computed with the conductor-like screening model for real solvents [COSMO-RS], for which we observe errors not exceeding 22 kJ mol-1. We thus propose with final uncertainty of about 20 kJ mol-1 standard enthalpies of formation of TBP, HDBP, and H2MBP which amounts to -1281.7 ± 24.4, -1229.4 ± 19.6, and -1176.7 ± 14.8 kJ mol-1, respectively, in the gas phase. In the liquid phase, the predicted values are -1367.3 ± 24.4, -1348.7 ± 19.6, and -1323.8± 14.8 kJ mol-1, to which we may add about -22 kJ mol-1 error from the COSMO-RS solvent model. From these data, the complete hydrolysis of TBP is predicted as an exothermic phenomena but showing a slightly endergonic process.

SYNTHESIS OF METHYL TERT-BUTYL ETHER CATALYZED BY ACIDIC ION-EXCHANGE RESINS - INFLUENCE OF THE PROTON ACTIVITY

NARCIS (Netherlands)

PANNEMAN, HJ; BEENACKERS, AACM

1995-01-01

The catalytic activity of various strong acid ion-exchange resins on the synthesis of methyl tert-butyl ether (MtBE) from methanol and isobutene has been investigated. Relative to Amberlyst 15, Kastel CS 381 and Amberlyst CSP have similar rate constants, whereas Duolite ES 276 and Amberlyst XE 307

Phosphate rock costs, prices and resources interaction.

Science.gov (United States)

Mew, M C

2016-01-15

This article gives the author's views and opinions as someone who has spent his working life analyzing the international phosphate sector as an independent consultant. His career spanned two price hike events in the mid-1970's and in 2008, both of which sparked considerable popular and academic interest concerning adequacy of phosphate rock resources, the impact of rising mining costs and the ability of mankind to feed future populations. An analysis of phosphate rock production costs derived from two major industry studies performed in 1983 and 2013 shows that in nominal terms, global average cash production costs increased by 27% to $38 per tonne fob mine in the 30 year period. In real terms, the global average cost of production has fallen. Despite the lack of upward pressure from increasing costs, phosphate rock market prices have shown two major spikes in the 30 years to 2013, with periods of less volatility in between. These price spike events can be seen to be related to the escalating investment cost required by new mine capacity, and as such can be expected to be repeated in future. As such, phosphate rock price volatility is likely to have more impact on food prices than rising phosphate rock production costs. However, as mining costs rise, recycling of P will also become increasingly driven by economics rather than legislation. Copyright © 2015 Elsevier B.V. All rights reserved.

Metal cation controls phosphate release in the myosin ATPase.

Science.gov (United States)

Ge, Jinghua; Huang, Furong; Nesmelov, Yuri E

2017-11-01

Myosin is an enzyme that utilizes ATP to produce a conformational change generating a force. The kinetics of the myosin reverse recovery stroke depends on the metal cation complexed with ATP. The reverse recovery stroke is slow for MgATP and fast for MnATP. The metal ion coordinates the γ phosphate of ATP in the myosin active site. It is accepted that the reverse recovery stroke is correlated with the phosphate release; therefore, magnesium "holds" phosphate tighter than manganese. Magnesium and manganese are similar ions in terms of their chemical properties and the shell complexation; hence, we propose to use these ions to study the mechanism of the phosphate release. Analysis of octahedral complexes of magnesium and manganese show that the partial charge of magnesium is higher than that of manganese and the slightly larger size of manganese ion makes its ionic potential smaller. We hypothesize that electrostatics play a role in keeping and releasing the abstracted γ phosphate in the active site, and the stronger electric charge of magnesium ion holds γ phosphate tighter. We used stable myosin-nucleotide analog complex and Raman spectroscopy to examine the effect of the metal cation on the relative position of γ phosphate analog in the active site. We found that in the manganese complex, the γ phosphate analog is 0.01 nm further away from ADP than in the magnesium complex. We conclude that the ionic potential of the metal cation plays a role in the retention of the abstracted phosphate. © 2017 The Protein Society.

DEVELOPMENT OF PHYSIOLOGICAL-BASED PHARMACOKINETIC MODEL FOR DERMAL ABSORPTION NAD PENETRATION OF METHYL TERTIARY BUTYL ETHER IN HUMANS

Science.gov (United States)

Background: Methyl tertiary butyl ether (MTBE) is a volatile organic chemical that is added to gasoline as an octane booster and to reduce vehicular emissions of carbon monoxide. MTBE is introduced into the environment through fuel spills, leakage of storage tanks, and evaporat...

Cyanotoxins: a poison that frees phosphate.

Science.gov (United States)

Raven, John A

2010-10-12

Autotrophic organisms obtain phosphorus from the environment by secreting alkaline phosphatases that act on esters, resulting in inorganic phosphate that is then taken up. New work shows that the cyanobacterium Aphanizomenon ovalisporum obtains inorganic phosphate by secreting the cyanotoxin cylindrospermopsin, which induces alkaline phosphatase in other phytoplankton species. Copyright © 2010 Elsevier Ltd. All rights reserved.

Phosphate coating on stainless steel 304 sensitized

International Nuclear Information System (INIS)

Cruz V, J. P.; Vite T, J.; Castillo S, M.; Vite T, M.

2009-01-01

The stainless steel 304 can be sensitized when welding processes are applied, that causes the precipitation of chromium carbide in the grain limits, being promoted in this way the formation of galvanic cells and consequently the corrosion process. Using a phosphate coating is possible to retard the physiochemical damages that can to happen in the corrosion process. The stainless steel 304 substrate sensitized it is phosphate to base of Zn-Mn, in a immersion cell very hot. During the process was considered optimization values, for the characterization equipment of X-rays diffraction and scanning electron microscopy was used. The XRD technique confirmed the presence of the phases of manganese phosphate, zinc phosphate, as well as the phase of the stainless steel 304. When increasing the temperature from 60 to 90 C in the immersion process a homogeneous coating is obtained. (Author)

Corrosion inhibition by lithium zinc phosphate pigment

International Nuclear Information System (INIS)

Alibakhshi, E.; Ghasemi, E.; Mahdavian, M.

2013-01-01

Highlights: •Synthesis of lithium zinc phosphate (LZP) by chemical co-precipitation method. •Corrosion inhibition activity of pigments compare with zinc phosphate (ZP). •LZP showed superior corrosion inhibition effect in EIS measurements. •Evaluation of adhesion strength and dispersion stability. -- Abstract: Lithium zinc phosphate (LZP) has been synthesized through a co-precipitation process and characterized by XRD and IR spectroscopy. The inhibitive performances of this pigment for corrosion of mild steel have been discussed in comparison with the zinc phosphate (ZP) in the pigment extract solution by means of EIS and in the epoxy coating by means of salt spray. The EIS and salt spray results revealed the superior corrosion inhibitive effect of LZP compared to ZP. Moreover, adhesion strength and dispersion stability of the pigmented epoxy coating showed the advantage of LZP compared to ZP

Global radiological impact of the phosphate fertilizers

International Nuclear Information System (INIS)

Morales, Rudnei Karam; Alves, Rex Nazare

1996-01-01

About ninety percent of the products obtained in the phosphate industry are directly used in agriculture as fertilizers. The uranium, thorium and radium content in phosphate fertilizers pollute the soil, water and air, creating risks due to associated natural radiation. This work shows the concentration of radionuclides present in various products of the national and American phosphate fertilizers industry, and compared them with worldwide mean values. The radiological impact of the products on the environment is evaluated and suggestions are presented in order to minimize the risks due to radioactivity. (author)

Determination of radioactivity in Chinese phosphate rock and fertilizer

International Nuclear Information System (INIS)

Chen Jingjian; Zhu Yongyi; Yang Juncheng

1993-01-01

The presented paper reported the radioactivity of U-238, Ra-226, Th-232 and K-40 in Chinese phosphate rocks by gamma spectrographic analysis during 1985-1990. The results showed that the decay chain of U-238-Ra-226 was the main source of radionuclides in phosphate rocks. The radionuclides in phosphate fertilizer differed from the forms of phosphate fertilizer. U-238 was the most important radionuclide in phosphoric compound fertilizer. The transfer rate of radionuclides was also estimated. (2 figs., 1 tab.)

Engineering Potato Starch with a Higher Phosphate Content.

Directory of Open Access Journals (Sweden)

Xuan Xu

Full Text Available Phosphate esters are responsible for valuable and unique functionalities of starch for industrial applications. Also in the cell phosphate esters play a role in starch metabolism, which so far has not been well characterized in storage starch. Laforin, a human enzyme composed of a carbohydrate-binding module and a dual-specificity phosphatase domain, is involved in the dephosphorylation of glycogen. To modify phosphate content and better understand starch (dephosphorylation in storage starch, laforin was engineered and introduced into potato (cultivar Kardal. Interestingly, expression of an (engineered laforin in potato resulted in significantly higher phosphate content of starch, and this result was confirmed in amylose-free potato genetic background (amf. Modified starches exhibited altered granule morphology and size compared to the control. About 20-30% of the transgenic lines of each series showed red-staining granules upon incubation with iodine, and contained higher phosphate content than the blue-stained starch granules. Moreover, low amylose content and altered gelatinization properties were observed in these red-stained starches. Principle component and correlation analysis disclosed a complex correlation between starch composition and starch physico-chemical properties. Ultimately, the expression level of endogenous genes involved in starch metabolism was analysed, revealing a compensatory response to the decrease of phosphate content in potato starch. This study provides a new perspective for engineering starch phosphate content in planta by making use of the compensatory mechanism in the plant itself.

Ecotoxicological evaluation of the additive butylated hydroxyanisole using a battery with six model systems and eighteen endpoints.

Science.gov (United States)

Jos, Angeles; Repetto, Guillermo; Ríos, Juan Carlos; del Peso, Ana; Salguero, Manuel; Hazen, María José; Molero, María Luisa; Fernández-Freire, Paloma; Pérez-Martín, Jose Manuel; Labrador, Verónica; Cameán, Ana

2005-01-26

The occurrence and fate of additives in the aquatic environment is an emerging issue in environmental chemistry. This paper describes the ecotoxicological effects of the commonly used additive butylated hydroxyanisole (BHA) using a test battery, comprising of several different organisms and in vitro test systems, representing a proportion of the different trophic levels. The most sensitive system to BHA was the inhibition of bioluminescence in Vibrio fischeri bacteria, which resulted in an acute low observed adverse effect concentration (LOAEC) of 0.28 microM. The next most sensitive system was the immobilization of the cladoceran Daphnia magna followed by: the inhibition of the growth of the unicellular alga Chlorella vulgaris; the endpoints evaluated in Vero (mammalian) cells (total protein content, LDH activity, neutral red uptake and MTT metabolization), mitotic index and root growth inhibition in the terrestrial plant Allium cepa, and finally, the endpoints used on the RTG-2 salmonid fish cell line (neutral red uptake, total protein content, MTS metabolization, lactate dehydrogenase leakage and activity, and glucose-6-phosphate dehydrogenase activity). Morphological alterations in RTG-2 cells were also assessed and these included loss of cells, induction of cellular pleomorphism, hydropic degeneration and induction of apoptosis at high concentrations. The results from this study also indicated that micronuclei were not induced in A.cepa exposed to BHA. The differences in sensitivity for the diverse systems that were used (EC50 ranged from 1.2 to >500 microM) suggest the importance for a test battery approach in the evaluation of the ecological consequences of chemicals. According to the results, the levels of BHA reported in industrial wastewater would elicit adverse effects in the environment. This, coupled with its potential to bioaccumulate, makes BHA a pollutant of concern not only for acute exposures, but also for the long-term.

Ethyl tertiary-butyl ether: a toxicological review.

Science.gov (United States)

McGregor, Douglas

2007-05-01

A number of oxygenated compounds (oxygenates) are available for use in gasoline to reduce vehicle exhaust emissions, reduce the aromatic compound content, and avoid the use of organo-lead compounds, while maintaining high octane numbers. Ethyl tertiary-butyl ether (ETBE) is one such compound. The current use of ETBE in gasoline or petrol is modest but increasing, with consequently similar trends in the potential for human exposure. Inhalation is the most likely mode of exposure, with about 30% of inhaled ETBE being retained by the lungs and distributed around the body. Following cessation of exposure, the blood concentration of ETBE falls rapidly, largely as a result of its metabolism to tertiary-butyl alcohol (TBA) and acetaldehyde. TBA may be further metabolized, first to 2-methyl-1,2-propanediol and then to 2-hydroxyisobutyrate, the two dominant metabolites found in urine of volunteers and rats. The rapid oxidation of acetaldehyde suggests that its blood concentration is unlikely to rise above normal as a result of human exposure to sources of ETBE. Single-dose toxicity tests show that ETBE has low toxicity and is essentially nonirritant to eyes and skin; it did not cause sensitization in a maximization test in guinea pigs. Neurological effects have been observed only at very high exposure concentrations. There is evidence for an effect of ETBE on the kidney of rats. Increases in kidney weight were seen in both sexes, but protein droplet accumulation (with alpha(2u)-globulin involvement) and sustained increases in cell proliferation occurred only in males. In liver, centrilobular necrosis was induced in mice, but not rats, after exposure by inhalation, although this lesion was reported in some rats exposed to very high oral doses of ETBE. The proportion of liver cells engaged in S-phase DNA synthesis was increased in mice of both sexes exposed by inhalation. ETBE has no specific effects on reproduction, development, or genetic material. Carcinogenicity studies

Phosphate and Cardiovascular Disease beyond Chronic Kidney Disease and Vascular Calcification

Directory of Open Access Journals (Sweden)

Sinee Disthabanchong

2018-01-01

Full Text Available Phosphate is essential for life but its accumulation can be detrimental. In end-stage renal disease, widespread vascular calcification occurs as a result of chronic phosphate load. The accumulation of phosphate is likely to occur long before the rise in serum phosphate above the normal range since several observational studies in both general population and early-stage CKD patients have identified the relationship between high-normal serum phosphate and adverse cardiovascular outcomes. Consumption of food high in phosphate increases both fasting and postprandial serum phosphate and habitual intake of high phosphate diet is associated with aging, cardiac hypertrophy, endothelial dysfunction, and subclinical atherosclerosis. The decline in renal function and dietary phosphate load can increase circulating fibroblast growth factor-23 (FGF-23 which may have a direct impact on cardiomyocytes. Increased FGF-23 levels in both CKD and general populations are associated with left ventricular hypertrophy, congestive heart failure, atrial fibrillation, and mortality. Increased extracellular phosphate directly affects endothelial cells causing cell apoptosis and vascular smooth muscle cells (VSMCs causing transformation to osteogenic phenotype. Excess of calcium and phosphate in the circulation can promote the formation of protein-mineral complex called calciprotein particles (CPPs. In CKD, these CPPs contain less calcification inhibitors, induce inflammation, and promote VSMC calcification.

An efficient method for qualitative screening of phosphate-solubilizing bacteria.

Science.gov (United States)

Mehta, S; Nautiyal, C S

2001-07-01

An efficient protocol was developed for qualitative screening of phosphate-solubilizing bacteria, based upon visual observation. Our results indicate that, by using our formulation containing bromophenol blue, it is possible to quickly screen on a qualitative basis the phosphate-solubilizing bacteria. Qualitative analysis of the phosphate solubilized by various groups correlated well with grouping based upon quantitative analysis of bacteria isolated from soil, effect of carbon, nitrogen, salts, and phosphate solubilization-defective transposon mutants. However, unlike quantitative analysis methods that involve time-consuming biochemical procedures, the time for screening phosphate-solubilizing bacteria is significantly reduced by using our simple protocol. Therefore, it is envisaged that usage of this formulation based upon qualitative analysis will be salutary for the quick screening of phosphate-solubilizing bacteria. Our results indicate that the formulation can also be used as a quality control test for expeditiously screening the commercial bioinoculant preparations, based on phosphate solubilizers.

Adsorption of butyl acetate in air over silver-loaded Y and ZSM-5 zeolites: experimental and modelling studies.

Science.gov (United States)

Bhatia, Subhash; Abdullah, Ahmad Zuhairi; Wong, Cheng Teng

2009-04-15

Adsorption behaviours of butyl acetate in air have been studied over silver-loaded Y (Si/Al=40) and ZSM-5 (Si/Al=140) zeolites. The silver metal was loaded into the zeolites by ion exchange (IE) and impregnation (IM) methods. The adsorption study was mainly conducted at a gas hourly space velocity (GHSV) of 13,000 h(-1) with the organic concentration of 1000 ppm while the desorption step was carried out at a GHSV of 5000 h(-1). The impregnated silver-loaded adsorbents showed lower uptake capacity and shorter breakthrough time by about 10 min, attributed to changes in the pore characteristics and available surface for adsorption. Silver exchanged Y (AgY(IE)) with lower hydrophobicity showed higher uptake capacity of up to 35%, longer adsorbent service time and easier desorption compared to AgZSM-5(IE). The presence of water vapour in the feed suppressed the butyl acetate adsorption of AgY(IE) by 42% due to the competitive adsorption of water on the surface and the effect was more pronounced at lower GHSV. Conversely, the adsorption capacity of AgZSM-5(IE) was minimally affected, attributed to the higher hydrophobicity of the material. A mathematical model is proposed to simulate the adsorption behaviour of butyl acetate over AgY(IE) and AgZSM-5(IE). The model parameters were successfully evaluated and used to accurately predict the breakthrough curves under various process conditions with root square mean errors of between 0.05 and 0.07.

Influence of protonation or alkylation of the phosphate group on the e. s. r. spectra and on the rate of phosphate elimination from 2-methoxyethyl phosphate 2-yl radicals. [. gamma. rays

Energy Technology Data Exchange (ETDEWEB)

Behrens, G; Koltzenburg, G; Ritter, A; Schulte-Frohlinde, D [Max-Planck-Institut fuer Kohlenforschung, Muelheim an der Ruhr (Germany, F.R.). Inst. fuer Strahlenchemie

1978-02-01

The e.s.r. spectra of l-yl, 2-yl and 3'-yl methoxethyl phosphate radicals derived from CH/sub 3/OCH/sub 2/CH/sub 2/-OPO/sub 3/H/sub 2/ by hydrogen abstraction have been measured in aqueous solutions and the hyperfine constants determined. The coupling constants vary strongly with protonation or alkylation of the phosphate group. The 2-yl radicals eliminate phosphate. The rate-constants for the elimination (ksub(e)) have been estimated by e.s.r. measurements and by product studies as a function of pH using /sup 60/Co ..gamma..-radiolysis. The ksub(e) values vary from approximately 0.3 s/sup -1/ for the CH/sub 3/OCHCH/sub 2/OPO/sub 3//sup - -/ radical and approximately 10/sup 3/s/sup -1/ for CH/sub 3/OCHCH/sub 2/OPO/sub 3/H/sup -/, to approximately 3 x 10/sup 6/s/sup -1/ for CH/sub 3/OCHCH/sub 2/OPO/sub 3/H/sub 2/. Alkylation of the phosphate group increased the elimination rate-constant to a similar extent as protonation. The results support a recent mechanism which described the OH-radical-induced single-strand breaks of DNA in aqueous solution starting from the C-4' radical of the sugar moiety. It is further concluded the C-4' radical of DNA eliminates the 3'-phosphate group faster than the 5'-phosphate group.

Final Report - Assessment of Potential Phosphate Ion-Cementitious Materials Interactions

International Nuclear Information System (INIS)

Naus, Dan J.; Mattus, Catherine H.; Dole, Leslie Robert

2007-01-01

The objectives of this limited study were to: (1) review the potential for degradation of cementitious materials due to exposure to high concentrations of phosphate ions; (2) provide an improved understanding of any significant factors that may lead to a requirement to establish exposure limits for concrete structures exposed to soils or ground waters containing high levels of phosphate ions; (3) recommend, as appropriate, whether a limitation on phosphate ion concentration in soils or ground water is required to avoid degradation of concrete structures; and (4) provide a 'primer' on factors that can affect the durability of concrete materials and structures in nuclear power plants. An assessment of the potential effects of phosphate ions on cementitious materials was made through a review of the literature, contacts with concrete research personnel, and conduct of a 'bench-scale' laboratory investigation. Results of these activities indicate that: no harmful interactions occur between phosphates and cementitious materials unless phosphates are present in the form of phosphoric acid; phosphates have been incorporated into concrete as set retarders, and phosphate cements have been used for infrastructure repair; no standards or guidelines exist pertaining to applications of reinforced concrete structures in high-phosphate environments; interactions of phosphate ions and cementitious materials has not been a concern of the research community; and laboratory results indicate similar performance of specimens cured in phosphate solutions and those cured in a calcium hydroxide solution after exposure periods of up to eighteen months. Relative to the 'primer,' a separate NUREG report has been prepared that provides a review of pertinent factors that can affect the durability of nuclear power plant reinforced concrete structures

Final Report - Assessment of Potential Phosphate Ion-Cementitious Materials Interactions

Energy Technology Data Exchange (ETDEWEB)

Naus, Dan J [ORNL; Mattus, Catherine H [ORNL; Dole, Leslie Robert [ORNL

2007-06-01

The objectives of this limited study were to: (1) review the potential for degradation of cementitious materials due to exposure to high concentrations of phosphate ions; (2) provide an improved understanding of any significant factors that may lead to a requirement to establish exposure limits for concrete structures exposed to soils or ground waters containing high levels of phosphate ions; (3) recommend, as appropriate, whether a limitation on phosphate ion concentration in soils or ground water is required to avoid degradation of concrete structures; and (4) provide a "primer" on factors that can affect the durability of concrete materials and structures in nuclear power plants. An assessment of the potential effects of phosphate ions on cementitious materials was made through a review of the literature, contacts with concrete research personnel, and conduct of a "bench-scale" laboratory investigation. Results of these activities indicate that: no harmful interactions occur between phosphates and cementitious materials unless phosphates are present in the form of phosphoric acid; phosphates have been incorporated into concrete as set retarders, and phosphate cements have been used for infrastructure repair; no standards or guidelines exist pertaining to applications of reinforced concrete structures in high-phosphate environments; interactions of phosphate ions and cementitious materials has not been a concern of the research community; and laboratory results indicate similar performance of specimens cured in phosphate solutions and those cured in a calcium hydroxide solution after exposure periods of up to eighteen months. Relative to the "primer," a separate NUREG report has been prepared that provides a review of pertinent factors that can affect the durability of nuclear power plant reinforced concrete structures.

Metabolism of the insecticidally active GABAA receptor antagonist 4-sec-[3,4-3H2]butyl-1-(4-cyanophenyl)-2,6,7-trioxabicyclo[2.2.2]octane

International Nuclear Information System (INIS)

Deng, Yanli; Palmer, C.J.; Toia, R.F.; Casida, J.E.

1990-01-01

4-sec-[3,4- 3 H 2 ]Butyl-1-(4-cyanophenyl)-2,6,7-trioxabicyclo[2.2.2]octane (referred to as [ 3 H]COB) was examined as an example of a new class of insecticidally active compounds that block the γ-aminobutyric acid gated chloride channel. Metabolites were identified by thin-layer cochromatography with standards from synthesis and by consideration of their hydrolytic and oxidative degradation products formed in situ on two-dimensional silica gel chromatoplates. Metabolism of [ 3 H]COB by mouse liver and housefly abdomen microsomes is dependent on fortification with NADPH. The O-methylene and sec-butyl sites are sensitive to oxidation. Each carbon of the sec-butyl group is individually functionalized with strong preference for the methylene site in the mouse but not the housefly microsomal system. O-Methylene hydroxylation initiates spontaneous cage opening to form an aldehyde that undergoes metabolic reduction, ultimately yielding the same cyanobenzoate ester of 2,2-bis-(hydroxymethyl)-3-methylpentan-1-ol formed by direct hydrolysis. Houseflies injected with [ 3 H]COB form many if not all of the same metabolites, with major products being the aforementioned cyanobenzoate, the orthoester oxidized at the sec-butyl methylene site, and polar conjugates