Effects of simulant mixed waste on EPDM and butyl rubber

International Nuclear Information System (INIS)

Nigrey, P.J.; Dickens, T.G.

1998-01-01

We have developed a Chemical Compatibility Testing Program for the evaluation of plastic packaging components which may be used in transporting mixed waste forms. In this program, we have screened 10 plastic materials in four liquid mixed waste simulants. These plastics were butadiene-acrylonitrile copolymer (Nitrile) rubber, cross-linked polyethylene, epi-chloro-hydrin rubber, ethylene-propylene (EPDM) rubber, fluorocarbons (Viton and Kel-F), poly-tetrafluoroethylene (Teflon), high-density polyethylene, isobutylene-isoprene copolymer (Butyl) rubber, polypropylene, and styrene-butadiene (SBR) rubber. The selected simulant mixed wastes were (1) an aqueous alkaline mixture of sodium nitrate and sodium nitrite; (2) a chlorinated hydrocarbon mixture; (3) a simulant liquid scintillation fluid; and (4) a mixture of ketones. The screening testing protocol involved exposing the respective materials to ∼3 kGy of gamma radiation followed by 14-day exposures to the waste simulants at 60 deg. C. The rubber materials or elastomers were tested using VTR measurements while the liner materials were tested using specific gravity as a metric. For these tests, screening criteria of ∼1 g/hr/m 2 for VTR and specific gravity change of 10% were used. Those materials that failed to meet these criteria were judged to have failed the screening tests and were excluded from the next phase of this experimental program. We have completed the comprehensive testing phase of liner materials in a simulant Hanford Tank waste consisting of an aqueous alkaline mixture of sodium nitrate and sodium nitrite. From the data analyses performed, we have identified the chloro-fluorocarbon Kel-F as having the greatest chemical durability after having been exposed to gamma radiation followed by exposure to the aqueous alkaline simulant mixed waste. The most striking observation from this study was the extremely poor performance of Teflon under these conditions. We have also completed the comprehensive

Radiation-induced copolymerization of styrene/n-butyl acrylate in the presence of ultra-fine powdered styrene-butadiene rubber

Energy Technology Data Exchange (ETDEWEB)

Yu Haibo [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Peng Jing [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China)], E-mail: jpeng@pku.edu.cn; Zhai Maolin; Li Jiuqiang; Wei Genshuan [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Qiao Jinliang [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); SINOPEC Beijing Research Institute of Chemical Industry, Beijing 100013 (China)

2007-11-15

Styrene (St)/n-butyl acrylate (BA) copolymers were prepared by two-stage polymerization: St/BA was pre-polymerized to a viscous state by bulk polymerization with initiation by benzoyl peroxide (BPO) followed by {sup 60}Co {gamma}-ray radiation curing. The resultant copolymers had higher molecular weight and narrower molecular weight distribution than conventional methods. After incorporation of ultra-fine powdered styrene-butadiene rubber (UFSBR) with a particle size of 100 nm in the monomer, the glass transition temperature (T{sub g}) of St-BA copolymer increased at low rubber content. Both the St-BA copolymer and the St-BA copolymer/UFSBR composites had good transparency at BA content below 40%.

Gamma irradiation induced effects of butyl rubber based damping material

Science.gov (United States)

Chen, Hong-Bing; Wang, Pu-Cheng; Liu, Bo; Zhang, Feng-Shun; Ao, Yin-Yong

2018-04-01

The effects of gamma irradiation on the butyl rubber based damping material (BRP) at various doses in nitrogen were investigated in this study. The results show that irradiation leads to radiolysis of BRP, with extractives increasing from 14.9 ± 0.8% of control to 37.2 ± 1.2% of sample irradiated at 350 kGy, while the swelling ratio increasing from 294 ± 3% to 766 ± 4%. The further investigation of the extractives with FTIR shows that the newly generated extractives are organic compounds containing C-H and C˭C bonds, with molecular weight ranging from 26,500 to 46,300. SEM characterization shows smoother surface with holes disappearing with increasing absorbed doses, consistent with "softer" material because of radiolysis. Dynamic mechanical study of BRP show that tan δ first slightly then obviously increases with increasing absorbed dose, while storage modulus slightly decreases. The tensile testing shows that the tensile strength decreases while the elongation at break increases with increasing dose. The positron annihilation lifetime spectroscopy show no obvious relations between free volume parameters and the damping properties, indicating the complicated influencing factors of damping properties.

New type of liquid rubber and compositions based on it.

Science.gov (United States)

Semikolenov, S V; Nartova, A V; Voronchikhin, V D; Dubkov, K A

2014-11-01

The new method for producing the functionalized polymers and oligomers containing carbonyl C=O groups is developed. The method is based on the noncatalytic oxidation of unsaturated rubbers by nitrous oxide (N2O) at 180-230 °С. The proposed method allows obtaining the new type of functionalized rubbers-liquid unsaturated polyketones with regulated molecular weight and concentration of C=O groups. The influence of the liquid polyketone addition on properties of rubber-based composites is investigated. The study indicates good prospects of using the liquid polyketones for the improvement of properties and operating characteristics of the various types of rubbers and the rubber-cord systems.

Mechanical and thermal properties of sisal fiber-reinforced rubber seed oil-based polyurethane composites

International Nuclear Information System (INIS)

Bakare, I.O.; Okieimen, F.E.; Pavithran, C.; Abdul Khalil, H.P.S.; Brahmakumar, M.

2010-01-01

The development of high-performance composite materials from locally sourced and renewable materials was investigated. Rubber seed oil polyurethane resin synthesized using rubber seed monoglyceride derived from glycerolysis of the oil was used as matrix in the composite samples. Rubber seed oil-based polyurethane composite reinforced with unidirectional sisal fibers were prepared and characterized. Results showed that the properties of unidirectional fiber-reinforced rubber seed oil-based polyurethane composites gave good thermal and mechanical properties. Also, the values of tensile strengths and flexural moduli of the polyurethane composites were more than tenfold and about twofold higher than un-reinforced rubber seed oil-based polyurethane. The improved thermal stability and the scanning electron micrographs of the fracture surface of the composites were attributed to good fiber-matrix interaction. These results indicate that high-performance 'all natural products' composite materials can be developed from resources that are readily available locally.

Natural rubber: leather composites

Directory of Open Access Journals (Sweden)

K. Ravichandran

2005-06-01

Full Text Available Leather is a fibrous protein consisting of collagen in a three dimensionally crosslinked network. Chrome tanning of leather improves the appearance of leather but at the same time emits both solid and liquid chrome leather wastes. Scrap rubber recycling using untreated and neutralized leather fibrous particles in natural rubber has been studied. Vulcanization, mechanical, morphological and swelling properties of the natural rubber - scrap rubber composites containing neutralized leather have been discussed. Use of chrome leather particles has been found to improve the consumption of scrap rubber powder in natural rubber formulations. Polymer composites based on leather wastes as fillers are reported to be useful for many applications such as in construction materials, automobile interior moldings, heat and sound insulating boards, shoe soles, flooring materials and moldings with good anti-static properties, air permeability and good appearances.

High Performance Graphene Oxide Based Rubber Composites

Science.gov (United States)

Mao, Yingyan; Wen, Shipeng; Chen, Yulong; Zhang, Fazhong; Panine, Pierre; Chan, Tung W.; Zhang, Liqun; Liang, Yongri; Liu, Li

2013-01-01

In this paper, graphene oxide/styrene-butadiene rubber (GO/SBR) composites with complete exfoliation of GO sheets were prepared by aqueous-phase mixing of GO colloid with SBR latex and a small loading of butadiene-styrene-vinyl-pyridine rubber (VPR) latex, followed by their co-coagulation. During co-coagulation, VPR not only plays a key role in the prevention of aggregation of GO sheets but also acts as an interface-bridge between GO and SBR. The results demonstrated that the mechanical properties of the GO/SBR composite with 2.0 vol.% GO is comparable with those of the SBR composite reinforced with 13.1 vol.% of carbon black (CB), with a low mass density and a good gas barrier ability to boot. The present work also showed that GO-silica/SBR composite exhibited outstanding wear resistance and low-rolling resistance which make GO-silica/SBR very competitive for the green tire application, opening up enormous opportunities to prepare high performance rubber composites for future engineering applications. PMID:23974435

Rubber Composites Based on Polar Elastomers with Incorporated Modified and Unmodified Magnetic Filler

Directory of Open Access Journals (Sweden)

Ján Kruželák

2016-01-01

Full Text Available Rubber magnetic composites were prepared by incorporation of unmodified and surface modified strontium ferrite into rubber matrices based on NBR and NBR/PVC. Strontium ferrite was dosed to the rubber matrices in concentration scale ranging from 0 to 100 phr. The main goal was to investigate the influence of the type of ferrite on the curing process, physical-mechanical and magnetic properties of composites. The mutual interactions between the filler and rubber matrices were investigated by determination of cross-link density and SEM analysis. The incorporation of magnetic fillers leads to the increase of cross-link density and remanent magnetic induction of composites. Moreover, the improvement of physical-mechanical properties was achieved in dependence on the content of magnetic fillers. Surface modification of ferrite contributed to the enhancement of adhesion on the interphase filler-rubber. It can be stated that ferrite exhibits reinforcing effect in the composite materials and this reinforcing behavior was emphasized with the increase in polarity of the rubber matrix.

Study of rheological, viscoelastic and vulcanization behavior of sponge EPDM/NR blended nano- composites

International Nuclear Information System (INIS)

Bashir, M Arshad; Shahid, M; Ahmed, Riaz; Yahya, A G

2014-01-01

In this research paper the effect of blending ratio of natural rubber (NR) with Ethylene Propylene Diene Monomer (EPDM) were investigated. Different samples of EPDM/NR ratio were prepared to study the variation of NR in EPDM on rheology, curing characteristics, tangent δ, and viscosity variation during vulcanization of sponge nano composites.The main aim of present research is to develop elastomeric based sponge composites with the blending ratio of base elastomers along with the carbon nano particles for high energy absorbing and damping applications. The curing characteristics, rheology and viscoelastic nature of the composite is remarkably influenced with the progressive blending ratio of the base elastomeric matrix

Study of rheological, viscoelastic and vulcanization behavior of sponge EPDM/NR blended nano-composites

International Nuclear Information System (INIS)

Bashir, M. A.; Shahid, M.; Ahmed, R.; Yahya, A. G.

2013-01-01

In this research paper the effect of blending ratio of natural rubber (NR) with Ethylene Propylene Diene Monomer (EPDM) were investigated. Different samples of EPDM/NR ratio were prepared to study the variation of NR in EPDM on rheology, curing characteristics, tangent d, and viscosity variation during vulcanization of sponge nano composites. The main aim of present research is to develop elastomeric based sponge composites with the blending ratio of base elastomers along with the carbon nano particles for high energy absorbing and damping applications. The curing characteristics, rheology and viscoelastic nature of the composite is remarkably influenced with the progressive blending ratio of the base elastomeric matrix. (author)

Effects of simulant mixed waste on EPDM and butyl rubber

International Nuclear Information System (INIS)

Nigrey, P.J.; Dickens, T.G.

1997-11-01

The authors have developed a Chemical Compatibility Testing Program for the evaluation of plastic packaging components which may be used in transporting mixed waste forms. In this program, they have screened 10 plastic materials in four liquid mixed waste simulants. These plastics were butadiene-acrylonitrile copolymer (Nitrile) rubber, cross-linked polyethylene, epichlorohydrin rubber, ethylene-propylene (EPDM) rubber, fluorocarbons (Viton and Kel-F trademark), polytetrafluoro-ethylene (Teflon), high-density polyethylene, isobutylene-isoprene copolymer (Butyl) rubber, polypropylene, and styrene-butadiene (SBR) rubber. The selected simulant mixed wastes were (1) an aqueous alkaline mixture of sodium nitrate and sodium nitrite; (2) a chlorinated hydrocarbon mixture; (3) a simulant liquid scintillation fluid; and (4) a mixture of ketones. The screening testing protocol involved exposing the respective materials to approximately 3 kGy of gamma radiation followed by 14-day exposures to the waste simulants at 60 C. The rubber materials or elastomers were tested using Vapor Transport Rate measurements while the liner materials were tested using specific gravity as a metric. The authors have developed a chemical compatibility program for the evaluation of plastic packaging components which may be incorporated in packaging for transporting mixed waste forms. From the data analyses performed to date, they have identified the thermoplastic, polychlorotrifluoroethylene, as having the greatest chemical compatibility after having been exposed to gamma radiation followed by exposure to the Hanford Tank simulant mixed waste. The most striking observation from this study was the poor performance of polytetrafluoroethylene under these conditions. In the evaluation of the two elastomeric materials they have concluded that while both materials exhibit remarkable resistance to these environmental conditions, EPDM has a greater resistance to this corrosive simulant mixed waste

ROMP-based polymer composites and biorenewable rubbers

Energy Technology Data Exchange (ETDEWEB)

Jeong, Wonje [Iowa State Univ., Ames, IA (United States)

2009-01-01

This research is divided into two related topics. In the first topic, the synthesis and characterization of novel composite materials reinforced with MWCNTs by ring-opening metathesis polymerization (ROMP) is reported for two ROMP based monomers: dicyclopentadiene (DCPD) and 5-ethylidene-2-norbornene (ENB). Homogeneous dispersion of MWCNTs in the polymer matrices is achieved by grafting norbornene moieties onto the nanotube surface. For the DCPD-based system, the investigation of mechanical properties of the composites shows a remarkable increase of tensile toughness with just 0.4 wt % of functionalized MWCNTs (f-MWCNTs). To our knowledge, this represents the highest toughness enhancement efficiency in thermosetting composites ever reported. DMA results show that there is a general increase of thermal stability (rg) with the addition of f-MWCNTs, which means that covalently bonded f-MWCNTs can reduce the local chain mobility of the matrix by interfacial interactions. The ENB system also shows significant enhancement of the toughness using just 0.8 wt % f-MWCNTs. These results indicate that the ROMP approach for polyENB is also very effective. The second topic is an investigation of the biorenewable rubbers synthesized by the tandem ROMP and cationic polymerization. The resin consists of a norbornenyl-modified linseed oil and a norbornene diester. Characterization of the bio-based rubbers includes dynamic mechanical analysis, tensile testing, and thermogravimetric analysis. The experimental results show that there is a decrease in glass transition temperature and slight increase of elongation with increased diester loading.

Development of natural rubber membranes for separation of methyl tert-butyl ether and methanol

International Nuclear Information System (INIS)

Nur Azrini Ramlee; Ghazali Mohd Nawawi; Khairul Zaman Dahlan

2010-01-01

As a new commercial process, membrane separation raises significant expectations in the process plant of the future and therefore this research was being initiated to develop and characterize pervaporation membrane based on natural rubber (NR). Natural Rubber SMR-L grade which was supplied by Malaysia Rubber Research Institute (MRRI) was used for the development of the membranes via interpenetrating polymer network (IPN) techniques. Polystyrene (PS) was used to modify the natural rubber to further improve their mechanical and chemical properties. The membranes were prepared with various blend ratios of natural rubber, polystyrene and divinyl benzene as cross linker with constant 1 % of dicumyl peroxide as the initiator. The developed membranes were then characterized to study the functional group presence, membranes morphology, crosslink density, tear strength, adsorption of the membranes and pervaporation separation of Methyl-Tert-Butyl-Ether (MTBE) and Methanol. Pervaporation process was conducted by using varies of MTBE concentration 10, 30, 50 and 70 wt % and at differ operation temperature, 25 degree Celsius and 55 degree Celsius. Separation performance of IPN NR/ PS membranes were based on the presented permeation flux and separation factor. Examination through Fourier Transform Infrared Spectroscopy (FTIR), determined crosslink density and tear strength, 6 series of IPN NR/ PS membranes were successfully developed using natural rubber. Observation from Scanning Electron Microscopy (SEM) showed that the membranes were dense and appropriated for the pervaporation process application. From the pervaporation of MTBE and Methanol, IPN NR/ PS membranes of series D4N30 shown low permeation flux of MTBE but high separation factor while D2N70 membranes was vice versa for both temperature of 25 degree Celsius and 55 degree Celsius. (author)

Neutron absorbing room temperature vulcanizable silicone rubber compositions

International Nuclear Information System (INIS)

Zoch, H.L.

1979-01-01

A neutron absorbing composition is described and consists of a one-component room temperature vulcanizable silicone rubber composition or a two-component room temperature vulcanizable silicone rubber composition in which the composition contains from 25 to 300 parts by weight based on the base silanol or vinyl containing diorganopolysiloxane polymer of a boron compound or boron powder as the neutron absorbing ingredient. An especially useful boron compound in this application is boron carbide. 20 claims

Ceramic compositions based on nano forsterite/nano magnesium aluminate spinel powders

International Nuclear Information System (INIS)

Khattab, R.M.; Wahsh, M.M.S.; Khalil, N.M.

2015-01-01

According to the wide applications in the field of chemical and engineering industries, forsterite (Mg_2SiO_4)/spinel (MgAl_2O_4) ceramic compositions were the matter of interest of several research works during the last three decades. This work aims at preparation and characterization of improved ceramic bodies based on forsterite and spinel nano powders through controlling the forsterite and spinel contents in the prepared mixes. These prepared ceramic compositions have been investigated through measuring the densification parameters, cold crushing strength as well as volume resistively. Nano spinel was added from 0 to 30 mass% on expense of nano forsterite matrix and fired at 1550 °C for 2 h. The phase composition of the fired samples was examined using x-ray diffraction (XRD) technique. The microstructure of some selected samples was shown using scanning electron microscope (SEM). A pronounced improvement in the sintering, mechanical properties and volume resistively were achieved with increasing of nano spinel addition up to 15 mass%. This is due to the improvement in the matrix of the prepared forsterite/spinel bodies as a result of well distribution of spinel in the forsterite matrix as depicted by SEM analysis. - Highlights: • Ceramic compositions based on nano forsterite/nano-MgAl_2O_4 spinel were synthesized. • CCS was improved (333.78 MPa) through 15 mass% of nano-MgAl_2O_4 spinel addition. • Volume resistivity was enhanced to 203*10"1"3 Ohm cm with 15 mass% of spinel addition. • Beyond 15 mass% spinel, CCS and volume resistivity were decreased.

Mechanism of n-butyl acrylate sensitization action in radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Sabharwal, S.; Chaudhari, C.V.; Bhardwaj, Y.K.; Majali, A.B.; Das, T.N.

1996-01-01

In order to understand the role of n-butyl acrylate (nBA) in radiation vulcanization of natural rubber latex, pulse radiolysis technique has been utilized to study the reactions of the transient species produced by reaction of OH . , e- aq and H . atoms with nBA in aqueous solutions. The results show that transients produced by reaction of e- aq with nBA alone are capable of propagating the polymerization reaction and enhance the vulcanization process. These results have been further confirmed by studying the effect of electron scavengers on the vulcanization behaviour of natural rubber latex in presence of nBA. (author). 3 refs., 3 figs

Dependence of mechanical characteristics from composition and structure and optimization of mechanical fracture energy of polymer composite material based on high-molecular rubbers

Directory of Open Access Journals (Sweden)

E. Nurullaev

2017-07-01

Full Text Available By means of numerical experiment the authors investigate dependence of conventional rupturing stress and mechanical fracture energy at uniaxial tension from fractional composition of dispersed filler, plasticizer volume fraction in polymer binder, effective density of transverse bonds, applied to development of covering for different purposes and with advanced service life in temperature range from 223 to 323 K. They compare mechanical characteristics of polymer composite materials (PCMs based on high- and low-molecular rubbers. It was shown that rupturing stress of high-molecular rubber-based PCM is of a higher magnitude than the stress of low-molecular rubber-based one at almost invariable rupturing deformation. Numerical simulation by variation of composition parameters and molecular structure enables evaluation of its maximum fracture energy which is 1000 times higher than mechanical fracture energy of similar composites based on low-molecular rubbers.

Natural rubber: leather composites

OpenAIRE

Ravichandran,K.; Natchimuthu,N.

2005-01-01

Leather is a fibrous protein consisting of collagen in a three dimensionally crosslinked network. Chrome tanning of leather improves the appearance of leather but at the same time emits both solid and liquid chrome leather wastes. Scrap rubber recycling using untreated and neutralized leather fibrous particles in natural rubber has been studied. Vulcanization, mechanical, morphological and swelling properties of the natural rubber - scrap rubber composites containing neutralized leather have ...

The influence of nano silica particles on gamma-irradiation ageing of elastomers based on chlorosulphonated polyethylene and acrylonitrile butadiene rubber

Science.gov (United States)

Marković, G.; Marinović-Cincović, M.; Tanasić, Lj.; Jovanović, V.; Samaržija-Jovanović, S.; Vukić, N.; Budinski-Simendić, J.

2011-12-01

The goal of this work was to study gamma irradiation ageing of rubber blends based on acrylonitrile butadiene rubber (NBR) and chlorosulphonated polyethylene rubber (CSM) reinforced by silica nano particles. The NBR/CSM compounds (50: 50, w/w) filled with different content of filler (0-100 phr) were crosslinked by sulfur. The vulcanization characteristics were assessed using the rheometer with an oscillating disk. The vulcanizates were prepared in a hydraulic press. The obtained materials were exposed to the different irradiation doses (100, 200, 300 and 400 kGy). The mechanical properties (hardness, modulus at 100% elongation, tensile strength and elongation at break) and swelling numbers were assessed before and after gamma irradiation ageing.

Performance of carbon fiber reinforced rubber composite armour against shaped charge jet penetration

Directory of Open Access Journals (Sweden)

Yue Lian-yong

2016-01-01

Full Text Available Natural rubber is reinforced with carbon fiber; the protective performances of the carbonfiber reinforced rubber composite armour to shaped charge jet have been studied based on the depth of penetration experiments. The craters on the witness blocks, the nature rubber based composite plates’ deformation and the Scanning Electron Microscopy for the hybrid fiber reinforced rubber plate also is analyzed. The results showed that the composite armour can affect the stability of the jet and made part of the jet fracture. The carbon fiber reinforced rubber composite armour has good defence ablity especially when the nature rubber plate hybrid 15% volume percentage carbonfiber and the obliquity angle is 68°. The hybrid fiber reinforced rubber composite armour can be used as a new kind of light protective armour.

Effect of expanded graphite and PEI-co-Silicon Rubber on the thermo mechanical, morphological as well as rheological properties of in situ composites based on poly (ether imide) and liquid crystalline polymer

Energy Technology Data Exchange (ETDEWEB)

Hatui, Goutam, E-mail: hatui.goutam@gmail.com; Malas, Asish, E-mail: malasasish@gmail.com; Bhattacharya, Pallab; Dhibar, Saptarshi, E-mail: saptaaus2007@gmail.com; Kundu, Mrinal Kanti, E-mail: kanti.mrinal19@gmail.com; Kumar Das, Chapal, E-mail: chapal12@yahoo.co.in

2015-01-15

Highlights: • PEI/LCP/ PEI-co-Silicon Rubber/EG and PEI/LCP/MWCNT nano composites are prepared by melt blending method. • The dispersions of acid modified expanded graphite were improved in presence of PEI-co-Silicon Rubber. • Thermal stability was found to be highest for PLGC composite. • Storage modulus and Young’s modulus showed an upward trend with incorporation of only EG and EG in presence of PEI-co-Silicon Rubber. • Among the nano composites PLGC has highest viscosity. - Abstract: Nanocomposites of polyether imide (PEI) and liquid crystalline polymer (LCP) with either MWCNT, Expanded Graphite (EG) or in combination of both EG and PEI-co-Silicon Rubber were prepared by melt blending process. The compatibility between the polymeric phases (PEI and LCP) was observed to be increased by the addition of PEI-co-Silicon Rubber while the only MWCNT added system (PLC) resulted in smaller LCP droplets. A continuous morphology was produced in presence of both PEI-co-Silicon Rubber and EG both added system (PLGR). This was due to the compatibilizing effect of PEI-co-Silicon Rubber. FTIR analysis revealed interaction between PEI and LCP in presence of PEI-co-Silicon Rubber. Remarkable increment of storage modulus was observed with the addition of EG and PEI-co-Silicon Rubber. Transmission Electron Microscope (TEM) analysis showed better dispersion of multiple graphene layers of EG in presence of PEI-co-Silicon Rubber compatibilized system. Tensile and Young’s modulus both were highest for EG/ PEI-co-Silicon Rubber added system. This is due to flexible compatibilizing effect of PEI-co-Silicon Rubber which delayed the detachment of LCP domain from the PEI matrix and thus detains the fracture.

Effect of expanded graphite and PEI-co-Silicon Rubber on the thermo mechanical, morphological as well as rheological properties of in situ composites based on poly (ether imide) and liquid crystalline polymer

International Nuclear Information System (INIS)

Hatui, Goutam; Malas, Asish; Bhattacharya, Pallab; Dhibar, Saptarshi; Kundu, Mrinal Kanti; Kumar Das, Chapal

2015-01-01

Highlights: • PEI/LCP/ PEI-co-Silicon Rubber/EG and PEI/LCP/MWCNT nano composites are prepared by melt blending method. • The dispersions of acid modified expanded graphite were improved in presence of PEI-co-Silicon Rubber. • Thermal stability was found to be highest for PLGC composite. • Storage modulus and Young’s modulus showed an upward trend with incorporation of only EG and EG in presence of PEI-co-Silicon Rubber. • Among the nano composites PLGC has highest viscosity. - Abstract: Nanocomposites of polyether imide (PEI) and liquid crystalline polymer (LCP) with either MWCNT, Expanded Graphite (EG) or in combination of both EG and PEI-co-Silicon Rubber were prepared by melt blending process. The compatibility between the polymeric phases (PEI and LCP) was observed to be increased by the addition of PEI-co-Silicon Rubber while the only MWCNT added system (PLC) resulted in smaller LCP droplets. A continuous morphology was produced in presence of both PEI-co-Silicon Rubber and EG both added system (PLGR). This was due to the compatibilizing effect of PEI-co-Silicon Rubber. FTIR analysis revealed interaction between PEI and LCP in presence of PEI-co-Silicon Rubber. Remarkable increment of storage modulus was observed with the addition of EG and PEI-co-Silicon Rubber. Transmission Electron Microscope (TEM) analysis showed better dispersion of multiple graphene layers of EG in presence of PEI-co-Silicon Rubber compatibilized system. Tensile and Young’s modulus both were highest for EG/ PEI-co-Silicon Rubber added system. This is due to flexible compatibilizing effect of PEI-co-Silicon Rubber which delayed the detachment of LCP domain from the PEI matrix and thus detains the fracture

Master curves for the sulphur assisted crosslinking reaction of natural rubber in the presence of nano- and nano-structured sp2 carbon allotropes

Directory of Open Access Journals (Sweden)

S. Musto

2017-06-01

Full Text Available In this paper, master curves are reported for the crosslinking of a diene rubber with a sulphur based system in the presence of either nano- or nano-structured carbon allotropes, such as carbon nanotubes (CNT, a nanosized graphite with high surface area (HSAG and carbon black (CB. Poly(1,4-cis-isoprene from Hevea Brasiliensis was the diene rubber and crosslinking was performed in temperatures ranging from 151 to 180 °C, with carbon allotropes below and above their percolation threshold. Such carbon allotropes were characterized by different aspect ratio, surface area and pH. However, in the crosslinking reaction, they revealed common behaviour. In fact, the specific interfacial area could be used to correlate crosslinking parameters, such as induction time (ts1 and activation energy (Ea calculated by applying the autocatalytic model. Monotonous decrease of ts1 and increase of Ea were observed, with points lying on master curves, regardless of the nature of the carbon allotropes. Remarkable differences were however observed in the structure of the crosslinking network: when the carbon allotrope was above the percolation threshold much larger crosslinking density was obtained in the presence of CNT whereas composites based on HSAG became soluble in hydrocarbon solvent, after the reaction with a thiol. Proposed explanation of these results is based on the reactivity of carbon allotropes with sulphur and sulphur based compounds, demonstrated through the reaction of 1-dodecanethiol and sulphur with CNT and HSAG and with a model substrate such as anthracene.

Performance of carbon fiber reinforced rubber composite armour against shaped charge jet penetration

OpenAIRE

Yue Lian-yong; Li Wei; Zu Xu-dong; Huang Zheng-xiang; Gao Zhen-yu

2016-01-01

Natural rubber is reinforced with carbon fiber; the protective performances of the carbonfiber reinforced rubber composite armour to shaped charge jet have been studied based on the depth of penetration experiments. The craters on the witness blocks, the nature rubber based composite plates’ deformation and the Scanning Electron Microscopy for the hybrid fiber reinforced rubber plate also is analyzed. The results showed that the composite armour can affect the stability of the jet and made pa...

Sugarcane bagasse ash: new filler to natural rubber composite

Directory of Open Access Journals (Sweden)

Renivaldo José dos Santos

2014-12-01

Full Text Available Waste recycling has been the subject of numerous scientific researches regarding the environmental care. This paper reports the redirecting of sugarcane bagasse ash (SBA as new filler to natural rubber (NR/SBA. The NR/SBA composites were prepared using an opened cylinder mixer to incorporate the vulcanization agents and different proportions of residue (SBA. The ash contains about 70-90% of inorganic compounds, with silica (SiO2 being the main compound. The SBA incorporation improved the mechanical properties of the vulcanized rubber. Based on these results, a new use is proposed for the agro-industry organic waste to be implemented in the rubber vulcanization process, aimed at improving the rubber physical properties as well as decreasing the prices of natural rubber composites.

Performance enhancement of quantum dot-sensitized solar cells based on polymer nano-composite catalyst

International Nuclear Information System (INIS)

Seo, Hyunwoong; Gopi, Chandu V.V.M.; Kim, Hee-Je; Itagaki, Naho; Koga, Kazunori; Shiratani, Masaharu

2017-01-01

Highlights: •We studied polymer nano-composite containing TiO 2 nano-particles as a catalyst. •Polymer nano-composite was applied for quantum dot-sensitized solar cells. •Polymer nano-composite catalyst was considerably improved with TiO 2 nano-particles. •Polymer nano-composite showed higher photovoltaic performance than conventional Au. -- Abstract: Polymer nano-composite composed of poly(3,4-ethylenedioxythiophene):poly (styrenesulfonate) and TiO 2 nano-particles was deposited on fluorine-doped tin oxide substrate and applied as an alternative to Au counter electrode of quantum dot-sensitized solar cell (QDSC). It became surface-richer with the increase in nano-particle amount so that catalytic reaction was increased by widened catalytic interface. Electrochemical impedance spectroscopy and cyclic voltammetry clearly demonstrated the enhancement of polymer nano-composite counter electrode. A QDSC based on polymer nano-composite counter electrode showed 0.56 V of V OC , 12.24 mA cm −2 of J SC , 0.57 of FF, and 3.87% of efficiency and this photovoltaic performance was higher than that of QDSC based on Au counter electrode (3.75%).

Electron spectroscopy of rubber and resin-based composites containing 2D carbon

International Nuclear Information System (INIS)

Kaciulis, S.; Mezzi, A.; Balijepalli, S.K.; Lavorgna, M.; Xia, H.S.

2015-01-01

Composite materials with 2D carbon (graphene and/or single wall carbon nanotubes) are very promising due to their extraordinary electrical and mechanical properties. Graphene and natural rubber composites, which may be used for the gaskets or sealants, were prepared by ultrasonically assisted latex-mixing exfoliation and in-situ reduction process, with two vulcanization approaches: roll-mixing and hot-pressing. Also the resin-based composites, filled with micro-particles of Ag and graphene or carbon nanotubes, have been studied. The standards for the compositional characterization of these materials still are not established. In addition to the mostly used techniques, such as Raman spectroscopy and electron microscopy, also Auger electron spectroscopy can be employed for the identification of graphene. In this study, the shape of C KVV peak, excited by electron beam and X-ray photons, has been investigated in different composite materials containing graphene and carbon nanotubes. A spectroscopic method for 2D carbon recognition, based on the D x parameter which is determined from C KVV signal excited by X-ray photons, was proposed and verified. Even a small content of graphene in different types of composites was sufficient for this recognition due to the dominating presence of graphene on the surface of composites. - Highlights: • Chemical composition of the rubber composites was determined by XPS. • Auger spectrum of carbon was used for graphene identification in composites. • Small content of graphene was sufficient for its recognition from the D parameter

Electron spectroscopy of rubber and resin-based composites containing 2D carbon

Energy Technology Data Exchange (ETDEWEB)

Kaciulis, S., E-mail: saulius.kaciulis@ismn.cnr.it [Institute for the Study of Nanostructured Materials, ISMN-CNR, P.O. Box 10, Monterotondo Stazione, 00015 Roma (Italy); Mezzi, A.; Balijepalli, S.K. [Institute for the Study of Nanostructured Materials, ISMN-CNR, P.O. Box 10, Monterotondo Stazione, 00015 Roma (Italy); Lavorgna, M. [Institute of Polymers, Composites and Biomaterials, IPCB-CNR, P.le Fermi, 80055 Napoli (Italy); Xia, H.S. [State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, 610065 Sichuan (China)

2015-04-30

Composite materials with 2D carbon (graphene and/or single wall carbon nanotubes) are very promising due to their extraordinary electrical and mechanical properties. Graphene and natural rubber composites, which may be used for the gaskets or sealants, were prepared by ultrasonically assisted latex-mixing exfoliation and in-situ reduction process, with two vulcanization approaches: roll-mixing and hot-pressing. Also the resin-based composites, filled with micro-particles of Ag and graphene or carbon nanotubes, have been studied. The standards for the compositional characterization of these materials still are not established. In addition to the mostly used techniques, such as Raman spectroscopy and electron microscopy, also Auger electron spectroscopy can be employed for the identification of graphene. In this study, the shape of C KVV peak, excited by electron beam and X-ray photons, has been investigated in different composite materials containing graphene and carbon nanotubes. A spectroscopic method for 2D carbon recognition, based on the D{sub x} parameter which is determined from C KVV signal excited by X-ray photons, was proposed and verified. Even a small content of graphene in different types of composites was sufficient for this recognition due to the dominating presence of graphene on the surface of composites. - Highlights: • Chemical composition of the rubber composites was determined by XPS. • Auger spectrum of carbon was used for graphene identification in composites. • Small content of graphene was sufficient for its recognition from the D parameter.

Radiation vulcanization of rubbers

Energy Technology Data Exchange (ETDEWEB)

Makuuchi, Keizo [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

2002-02-01

An abstract of the radiation process of polymer materials and the polymer reaction by radiation is explained. Main radiation is 250 keV to 10 MeV of electron rays in the industry. Radiation cross-linked rubber has less the tensile strength than that by sulfur and organic peroxide crosslinking. The main origins of low tensile strength are caused by cut of backbone chain and ozone depend on radiation. Acceleration of crosslinking and short time of radiation are necessary to improve these defects. To accelerate crosslinking, we used crosslinking accelerators, for example, three poly-functional monomers (PFM). The maximum tensile strength of styrene-butadiene rubber (SBR) not added crosslinking accelerators showed 3 MPa at 110 kGy, but SBR added A-TMMT (tetramethylolmethane tetraacrylate) showed 5.5 MPa at 110 kGy. Radiation crosslinking of many kinds of rubber: isoprene (IR), SBR, CR, nitrile rubber (NBR), hydrogenated nitrile rubber (HNBR), butyl rubber (IIR), chlorinated butyl rubber (CIIR), EPM and TPE are explained. (S.Y.)

Radiation vulcanization of rubbers

International Nuclear Information System (INIS)

Makuuchi, Keizo

2002-01-01

An abstract of the radiation process of polymer materials and the polymer reaction by radiation is explained. Main radiation is 250 keV to 10 MeV of electron rays in the industry. Radiation cross-linked rubber has less the tensile strength than that by sulfur and organic peroxide crosslinking. The main origins of low tensile strength are caused by cut of backbone chain and ozone depend on radiation. Acceleration of crosslinking and short time of radiation are necessary to improve these defects. To accelerate crosslinking, we used crosslinking accelerators, for example, three poly-functional monomers (PFM). The maximum tensile strength of styrene-butadiene rubber (SBR) not added crosslinking accelerators showed 3 MPa at 110 kGy, but SBR added A-TMMT (tetramethylolmethane tetraacrylate) showed 5.5 MPa at 110 kGy. Radiation crosslinking of many kinds of rubber: isoprene (IR), SBR, CR, nitrile rubber (NBR), hydrogenated nitrile rubber (HNBR), butyl rubber (IIR), chlorinated butyl rubber (CIIR), EPM and TPE are explained. (S.Y.)

Positron annihilation analysis of epoxy/hydroxyl terminated butyl nitrile rubber (EP/HTBN) system

International Nuclear Information System (INIS)

Zeng Minfeng; Chen Ning; Ji Genzhong; Sun Xudong; Zhao Rener; Xiao Huiquan; Qi Chenze; Wang Baoyi

2007-01-01

The free volume properties of epoxy/hydroxyl terminated butyl nitrile rubber (EP/HTBN) have been studied by means of positron annihilation technique. The toughness effect is found to be correlated with the content of HTBN and the free volume properties of the EP/HTBN interfaces. When the content of HTBN component is 5%, the free volume size in the interface is close to that of EP, and the toughness effect is strong. But with further addition of HTBN, holes with big size free volume are formed in the interface, and the toughness effect is limited. (authors)

Natural rubber/nitrile butadiene rubber/hindered phenol composites with high-damping properties

Directory of Open Access Journals (Sweden)

Xiuying Zhao

2015-10-01

Full Text Available New natural rubber (NR/nitrile butadiene rubber (NBR/hindered phenol (AO-80 composites with high-damping properties were prepared in this study. The morphological, structural, and mechanical properties were characterized by atomic force microscopy (AFM, polarized Fourier transform infrared spectrometer (FTIR, dynamic mechanical thermal analyzer (DMTA, and a tensile tester. Each composite consisted of two phases: the NR phase and the NBR/AO-80 phase. There was partial compatibility between the NR phase and the NBR/AO-80 phase, and the NR/NBR/AO-80 (50/50/20 composite exhibited a co-continuous morphology. Strain-induced crystallization occurred in the NR phase at strains higher than 200%, and strain-induced orientation appeared in the NBR/AO-80 phase with the increase of strain from 100% to 500%. The composites had a special stress–strain behavior and mechanical properties because of the simultaneous strain-induced orientation and strain-induced crystallization. In the working temperature range of a seismic isolation bearing, the composites (especially the NR/NBR/AO-80 (50/50/20 composite presented a high loss factor, high area of loss peak (TA, and high hysteresis energy. Therefore, the NR/NBR/AO-80 rubber composites are expected to have important application as a high-performance damping material for rubber bearing.

Fabrication of Wood-Rubber Composites Using Rubber Compound as a Bonding Agent Instead of Adhesives

Directory of Open Access Journals (Sweden)

Dongwei Shao

2016-06-01

Full Text Available Differing from the hot-pressing method in the manufacturing of traditional wood-rubber composites (WRCs, this study was aimed at fabricating WRCs using rubber processing to improve water resistance and mechanical properties. Three steps were used to make WRCs, namely, fiber-rubber mixing, tabletting, and the vulcanization molding process. Ninety-six WRC panels were made with wood fiber contents of 0%–50% at rotor rotational speeds of 15–45 rpm and filled coefficients of 0.55–0.75. Four regression equations, i.e., the tensile strength (Ts, elongation at break (Eb, hardness (Ha and rebound resilience (Rr as functions of fiber contents, rotational speed and filled coefficient, were derived and a nonlinear programming model were developed to obtain the optimum composite properties. Although the Ts, Eb and Rr of the panels were reduced, Ha was considerably increased by 17%–58% because of the wood fiber addition. Scanning electron microscope images indicated that fibers were well embedded in rubber matrix. The 24 h water absorption was only 1%–3%, which was much lower than commercial wood-based composites.

Fabrication of Wood-Rubber Composites Using Rubber Compound as a Bonding Agent Instead of Adhesives.

Science.gov (United States)

Shao, Dongwei; Xu, Min; Cai, Liping; Shi, Sheldon Q

2016-06-14

Differing from the hot-pressing method in the manufacturing of traditional wood-rubber composites (WRCs), this study was aimed at fabricating WRCs using rubber processing to improve water resistance and mechanical properties. Three steps were used to make WRCs, namely, fiber-rubber mixing, tabletting, and the vulcanization molding process. Ninety-six WRC panels were made with wood fiber contents of 0%-50% at rotor rotational speeds of 15-45 rpm and filled coefficients of 0.55-0.75. Four regression equations, i.e. , the tensile strength ( T s), elongation at break ( E b), hardness ( H a) and rebound resilience ( R r) as functions of fiber contents, rotational speed and filled coefficient, were derived and a nonlinear programming model were developed to obtain the optimum composite properties. Although the T s, E b and R r of the panels were reduced, H a was considerably increased by 17%-58% because of the wood fiber addition. Scanning electron microscope images indicated that fibers were well embedded in rubber matrix. The 24 h water absorption was only 1%-3%, which was much lower than commercial wood-based composites.

The Optimum Processing Parameter of Carbon Nano tubes and Thermoplastic Natural Rubber (NR/LNR/LLDPE) Composites Based on Tensile Properties

International Nuclear Information System (INIS)

Hazwani Halim; Syed Yusainee Syed Yahya; Sahrim Ahmad; Tarawneh, M.A.; Shamsul Bahri, A.R.

2011-01-01

In this study, the exact processing parameter including mixing time, rotor speed and temperature of CNTs and TPNR (NR/LNR/LLDPE) composite has been examined using tensile properties. To prepare the composite, the matrix NR/LLDPE will compatabilized using liquid natural rubber (LNR) with 40 % NR, 10 % LNR and 50 % LLDPE. Then, 2 % CNTs will be incorporated into the matrix using different processing temperature, rotor speed and mixing time. For the temperature, different temperature that used are 135, 140, 145, 150 and 155 degree and for the rotor speed 45, 50, 55, 60 and 65 rpm have been used. As for the mixing time, five different time have been investigated which is 9 min,11 min, 13 min, 15 min and 17 min. The results for Young's modulus and elongation at break show that there is the maximum increment for the composite that have been prepared using 140 degree Celsius, 55 rpm and 13 min. However when the temperature has been increased, both of these properties has been decreased. Based on these results we can conclude that the optimum processing parameter for these CNTs composite is quite similar with the composite of the matrix (TPNR) itself. (author)

Synthesis and thermal characterization of CdS nano crystals in previously formed template of maleic anhydride-octene 1-vinyl butyl terpolymer

International Nuclear Information System (INIS)

Akbarov, O.H; Mammadova, R.E; Malikov, E.Y.

2008-01-01

Full text: Nano crystals have dimensions in the range 10100 nm. Crystals in this size range possess unique properties, which enable scientists to manufacture materials and devices capable of performing unimaginable tasks. For that reason synthesis of this semiconductor nano crystals is expedient. Many useful methods have been used for preparing sulphide semiconductor nano crystals, such as colloidal chemistry method, sol-gel method, inverse micelle method, in situ synthesis and assemble on polymer template. The most significant method is in situ synthesis and assemble of sulphide semiconductor nano crystals on polymer. Compared with other methods, the stability of nanoparticles is improved by the protection and confinement of the copolymer. Because of confinement and protection effects of template environmental risk is prevented in this method. On the base of this principles in situ synthesis of CdS nano crystals in maleic anhydride-octene 1-vinyl butyl terpolymer was realized in this scientific work. First of all in specific condition maleic anhydride, octene 1, and vinyl butyl ether were polymerized to form a terpolymer as the result of radical ter polymerization. In second step CdS nano crystals were synthesized in N,N-dimethylformamide solution of maleic anhydride-octene 1-vinyl butyl terpolymer through the reaction of thiourea with cadmium chloride. In this process CdCI 2 x 2.5H 2 O was dissolved in N,N-dimethylformamide solution of previously formed terpolymer and was heated in 90 0 C temperature for 4 hours with vigorous stirring. Then desired amount of thiourea in N,N-dimethylformamide was quickly injected into the reaction flask using a syringe. The reaction continued for another 1 hour, and a yellow clear solution was obtained, which indicated the formation of CdS nano crystals

Radiation vulcanization of natural rubber latex using irradiation n-butyl acrylate aqueous emulsion as sensitizer

International Nuclear Information System (INIS)

Vo Van Thien; Nguyen Quoc Hien; Keizo Makuuchi; Fumio Yoshii

2000-01-01

Natural rubber latex was vulcanized by gamma radiation with n-butyl acrylate aqueous emulsion irradiated at dose of 1.5 kGy as sensitizer. The total solid content of latex increases on the irradiation dose. The viscosity of latex on the standing time was investigated and became stable after one month of storage. The gel content of latex films increasing with irradiation dose and attained more than 94% at dose of 10 kGy. Tensile strength of films reached the values of 31MPa; 30 Mpa and 25 Mpa at vulcanization doses of 20 kGy, 15 kGy and 8 kGy for the concentrations of sensitizer 7 phr, 9 phr and 13 phr respectively. Elongation at break decreases as increasing dose. Tear strength of rubber films was from 30-40 N/mm. The tackiness of latex films decreases and smell of vulcanized latex is almost negligible. (author)

A silicone rubber based composites using n-octadecane/poly (styrene-methyl methacrylate microcapsules as energy storage particle

Directory of Open Access Journals (Sweden)

W.L. Wu

Full Text Available A phase-change energy-storage material, silicone rubber (SR coated n-octadecane/poly (styrene-methyl methacrylate (SR/OD/P(St-MMA microcapsule composites, was prepared by mixing SR and OD/P(St-MMA microcapsules. The microcapsule content and silicone rubber coated method were investigated. The morphology and thermal properties of the composites were characterized by scanning electron microscopy (SEM, thermogravimetric analysis (TG, differential scanning calorimetry (DSC and heat storage properties. The results showed that the thermal and mechanical properties of SR/OD/P(St-MMA composites were excellent when the microcapsules were coated with room temperature vulcanized silicone rubber (RTVSR, of which content was 2 phr (per hundred rubber. The enthalpy value of the composites was 67.6 J g−1 and the composites were found to have good energy storage function. Keywords: n-Octadecane, Silicone rubber, Microcapsule, Energy-storage, Composites

New Green Polymeric Composites Based on Hemp and Natural Rubber Processed by Electron Beam Irradiation

Directory of Open Access Journals (Sweden)

Maria-Daniela Stelescu

2014-01-01

Full Text Available A new polymeric composite based on natural rubber reinforced with hemp has been processed by electron beam irradiation and characterized by several methods. The mechanical characteristics: gel fraction, crosslink density, water uptake, swelling parameters, and FTIR of natural rubber/hemp fiber composites have been investigated as a function of the hemp content and absorbed dose. Physical and mechanical properties present a significant improvement as a result of adding hemp fibres in blends. Our experiments showed that the hemp fibers have a reinforcing effect on natural rubber similar to mineral fillers (chalk, carbon black, silica. The crosslinking rates of samples, measured using the Flory-Rehner equation, increase as a result of the amount of hemp in blends and the electron beam irradiation dose increasing. The swelling parameters of samples significantly depend on the amount of hemp in blends, because the latter have hydrophilic characteristics.

Performance Study of the Natural Rubber Composite with Clay Minerals

International Nuclear Information System (INIS)

Nyo Nyo Myint; Tin Tin Aye; Kyaw Myo Naing; Nyunt Wynn

2008-03-01

The preparation, characterization and some applications of natural rubber clay composite have been studied. This study investigated the possibility of natural rubber latex to replace some part of natural clays. In formulation of rubber clay composite from natural rubber latex and various clay minerals, three main steps were involved (i) preparation of latex cream (ii) prevulcanization of latex cream (iii) mixing vulcanized latex compound, with other ingredients. In each step, several parameters have been carefully investigated to optimize the performance of natural rubber clay composite production. The composite products were of better quality and can be considered to be more cost effective.

Optimization of mechanical performance of oxidative nano-particle electrode nitrile butadiene rubber conducting polymer actuator.

Science.gov (United States)

Kim, Baek-Chul; Park, S J; Cho, M S; Lee, Y; Nam, J D; Choi, H R; Koo, J C

2009-12-01

Present work delivers a systematical evaluation of actuation efficiency of a nano-particle electrode conducting polymer actuator fabricated based on Nitrile Butadiene Rubber (NBR). Attempts are made for maximizing mechanical functionality of the nano-particle electrode conducting polymer actuator that can be driven in the air. As the conducting polymer polypyrrole of the actuator is to be fabricated through a chemical oxidation polymerization process that may impose certain limitations on both electrical and mechanical functionality of the actuator, a coordinated study for optimization process of the actuator is necessary for maximizing its performance. In this article actuation behaviors of the nano-particle electrode polypyrrole conducting polymer is studied and an optimization process for the mechanical performance maximization is performed.

Novel in situ coordinated cerium salt/acrylonitrile-butadiene rubber composite

International Nuclear Information System (INIS)

Han, Jianjun; Lu, Haifeng; Zhang, Jie; Feng, Shengyu

2012-01-01

A novel rubber composite of acrylonitrile-butadiene rubber (NBR) filled with cerium salt particles was vulcanized via in situ coordination for the first time. The resulting materials exhibit good mechanical properties. Curing characteristics analysis, differential scanning calorimetry, X-ray photoelectron spectroscopy, tensile testing, and an equilibrium swelling method were used for the characterization of the composite. The results in this paper indicate that the composite is a kind of elastomer based on the in situ coordination crosslinking interactions between the nitrile groups (–CN) of NBR and cerium ions. The mechanical properties of vulcanized cerium salt/ NBR rubber are altered when changing the sorts of cerium salt. Moreover, these materials show good irradiation resistance because of the introduction of the cerium salt. -- Highlights: ► Cerium salts were firstly used to vulcanize the acrylonitrile-butadiene rubber. ► Cerium salts act as not only crosslink agents but also reinforcing fillers in the matrix. ► These materials show good irradiation resistance and mechanical properties at same time.

Morphological and mechanical properties of styrene butadiene rubber/nano copper nanocomposites

Directory of Open Access Journals (Sweden)

Maryam Hadizadeh Harandi

Full Text Available In this research, rubber based nanocomposites with presence of nanoparticle has been studied. Styrene butadiene rubber (SBR/nanocopper (NC composites were prepared using two-roll mill method. Transmission electron microscope (TEM and scanning electron microscope (SEM images showed proper dispersion of NC in the SBR matrix without substantial agglomeration of nanoparticles. To evaluate the curing properties of nanocomposite samples, swelling and cure rheometric tests were conducted. Moreover, the rheological studies were carried out over a range of shear rates. The effect of NC particles was examined on the thermal behavior of the SBR using thermal gravimetric analysis (TGA. Furthermore, tensile tests were employed to investigate the capability of nanoparticles to enhance mechanical behavior of the compounds. The results showed enhancement in tensile properties with incorporation of NC to SBR matrix. Moreover, addition of NC increased shear viscosity and curing time of SBR composites. Keywords: Nanocopper, Rubber, Curing behavior, Rheological properties, Thermal stability, Tensile characteristics

Effect of sulfur and Nano- carbon black on the mechanical properties of hard rubber

Directory of Open Access Journals (Sweden)

Mohamed Hamza Al-Maamori

2018-01-01

Full Text Available To improve the properties of hard rubber(Ebonite from natural rubber, added Nano-Carbon black, where measured the properties of tensile, density, hardness and the properties of the vulcanization of a group of samples with different amount of sulfur from 18-36 pphr and different of carbon black (18-26-30 pphr. The results showed that the best carbon black ratio is 30 pphr, where it gives a balance between tensile properties of hand and toughness and flexibility of on the other hand and reduce brittleness in hard rubber.

Thermostability and surface morphology of nano- and micro-filled NBR/CSM and CR/CSM rubber blends

Directory of Open Access Journals (Sweden)

M. MARINOVIC-CINCOVIC

2004-02-01

Full Text Available Acrylonitrile-butadiene rubber (NBR, polychloroprene rubber (CR, chlorosulphonated polyethylene rubber (CSM and their blends were cross-linked with sulphur, ethylene-thiourea, magnesium oxide or their combination. The effect of nano- and micro- particle sized of 35 pphr SiO2 on the thermostability and surface morphology of all the crosslinked systems was investigated. Identification of the structure of nano- and micro- particle sized SiO2 filled NBR/CSM and CR/CSM crosslinked systems was carried out by Fourier transform infrared spectroscopy (FTIR with an attenuated total reflectance (ATR extension. The thermal stability of the nano- and micro- particle sized SiO2 filled NBR/CSM and CR/CSM crosslinked systems were carried out by thermogravimetric analysis (TGA. The glass transition temperature (Tg of the samples was determined by differential scanning calorimetry (DSC. The morphology of the fracture surface of the crosslinked systems was carried out by scanning electron microscope (SEM. The results show when filled with nano-particle sized of SiO2 NBR/CSM and CR/CSM polymer matrix have a strong peak from SiO–C at 1079 cm-1. This suggests the an interaction between the SiO2, which should lead to an increased thermal stability, higher values of Tg, better dispersion the nano-SiO2 and more polish, without cracks than micro-filled NBR/CSM and CR/CSM crosslinked systems.

Recycling of pneumatic scrap tyre into nano-crumb rubber by pulsed laser ablation in different pH media

Science.gov (United States)

Ezaan Khamsan, Nur; Bidin, Noriah; Islam, Shumaila; Daud, Suzairi; Krishnan, Ganesan; Bakar, Mohamad Aizat A.; Naqiuddin Razali, Muhamad; Khamis, Jamil

2018-05-01

Nano crumb rubber from scrap tyre is synthesized via 1064 nm pulsed Nd:YAG laser ablation in three different pH media i.e. DI-water (pH∼6.45), D-limonene (pH∼3.47) and NaOH solution (pH∼13.41). Field Emission Scanning Electron Microscope (FESEM) results show spherical morphology of crumb rubber with high degree of aggregation in DI-water and in D-limonene. However, dispersion of crumb rubbers is observed in NaOH solution. The smallest particles size is obtained in NaOH solution within the range of 10.9 nm – 74.3 nm. Energy-dispersive X-ray spectroscopy (EDX) and FTIR analysis confirmed the elements distribution and chemical bonding of rubber with DI-water, D-limonene and NaOH solution. The experimental findings shows that pulsed Nd:YAG laser ablation has potential for fabricating nano-crumb rubber in liquid media.

Functionalized Multi walled Carbon Nano tubes-Reinforced Viny lester/Epoxy Blend Based Nano composites: Enhanced Mechanical, Thermal, and Electrical Properties

International Nuclear Information System (INIS)

Praharaj, A. P.; Behera, D.; Bastia, T. K.; Rout, A. K.

2015-01-01

This paper presents a study on the mechanical, thermal, and electrical characterization of a new class of low cost multiphase nano composites consisting of Vinyl ester resin/epoxy (VER/EP) blend (40:60 w/w) reinforced with amine functionalized multi walled carbon nano tubes (f-MWCNTs). Five different sets of VER/EP nano composites are fabricated with addition of 0, 1, 3, 5, and 7 wt.% of f-MWCNTs. A detailed investigation of mechanical properties like tensile strength, impact strength, Young’s modulus, and hardness, thermal properties like thermogravimetric analysis (TGA) and thermal conductivity, electrical properties like dielectric strength, dielectric constant, and electrical conductivity, and corrosive and swelling properties of the nano composites has been carried out. Here, we report significant improvement in all the above properties of the fabricated nano composites with nano filler (f-MWCNTs) addition compared to the virgin blend (0 wt. nano filler loading). The properties are best observed in case of 5 wt.% nano filler loading with gradual deterioration thereafter which may be due to the nucleating tendency of the nano filler particles. Thus the above nano composites could be a preferable candidate for a wide range of structural, thermal, electrical, and solvent based applications.

Fatigue of cord-rubber composites for tires

Science.gov (United States)

Song, Jaehoon

stresses, the fatigue life of belt composites is predominantly influenced by the magnitude of maximum stress. Maximum cyclic strain of composite laminates at failure, which measures the total strain accumulation for gross failure, was independent of stress amplitude and close to the level of static failure strain. For all composite laminates under study, a linear correlation could be established between the temperature rise rate and dynamic creep rate which was, in turn, inversely proportional to the fatigue lifetime. Using the acoustic emission (AE) initiation stress value, better prediction of fatigue life was available for the fiber-reinforced composites having fatigue limit. The accumulation rate of AE activities during cyclic loading was linearly proportional to the maximum applied load and to the inverse of the fatigue life of cord-rubber composite laminates. Finally, a modified fatigue modulus model based on combination of power-law and logarithmic relation was proposed to predict the fatigue lifetime profile of cord-rubber composite laminates.

Properties of Vulcanized Polyisoprene Rubber Composites Filled with Opalized White Tuff and Precipitated Silica

Directory of Open Access Journals (Sweden)

Suzana Samaržija-Jovanović

2014-01-01

Full Text Available Opalized white tuff (OWT with 40 μm average particle size and 39.3 m2/g specific surface area has been introduced into polyisoprene rubber (NR. Their reinforcing effects were evaluated by comparisons with those from precipitated silica (PSi. The cure characteristic, apparent activation energy of cross-link (Eac and reversion (Ear, and mechanical properties of a variety of composites based on these rubbers were studied. This was done using vulcanization techniques, mechanical testing, and scanning electron microscopy (SEM. The results showed that OWT can greatly improve the vulcanizing process by shortening the time of optimum cure (tc90 and the scorch time (ts2 of cross-linked rubber composites, which improves production efficiency and operational security. The rubber composites filled with 50 phr of OWT were found to have good mechanical and elastomeric properties. The tensile strengths of the NR/OWT composites are close to those of NR/PSi composites, but the tear strength and modulus are not as good as the corresponding properties of those containing precipitated silica. Morphology results revealed that the OWT is poorly dispersed in the rubber matrix. According to that, the lower interactions between OWT and polyisoprene rubber macromolecules are obtained, but similar mechanical properties of NR/OWT (100/50 rubber composites compared with NR/PSi (100/50 rubber composites are resulted.

Radiation graft copolymerization of n-butyl acrylate on natural rubber latex

International Nuclear Information System (INIS)

Sundardi, F.; Kadariah, S.

1986-01-01

A method of radiation graft copolymerization of n-butyl acrylate (NBA) on natural rubber (NR) latex has been studied. The rate of conversion increases with the increase of NBA in latex. An irradiation dose of about 12 kGy is needed to obtain 90% conversion with 40 phr of NBA in latex. Tensile strength, tear strength, and elongation at break of grafted NR are found to decrease with increasing degree of grafting. The physical strength of a vulcanizate prepared from a mixture of NR and ply-NBA was found to be better than that of NBA-NR graft copolymer vulcanizate. The graft copolymerization reaction takes place in the outer layer of NR particles, and because the secondary bonds between poly-NBA molecules may be weaker than those between NR molecules, the existence of a poly-NBA layer in NR particles will decrease its physical strength

A silicone rubber based composites using n-octadecane/poly (styrene-methyl methacrylate) microcapsules as energy storage particle

Science.gov (United States)

Wu, W. L.; Chen, Z.

A phase-change energy-storage material, silicone rubber (SR) coated n-octadecane/poly (styrene-methyl methacrylate) (SR/OD/P(St-MMA)) microcapsule composites, was prepared by mixing SR and OD/P(St-MMA) microcapsules. The microcapsule content and silicone rubber coated method were investigated. The morphology and thermal properties of the composites were characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TG), differential scanning calorimetry (DSC) and heat storage properties. The results showed that the thermal and mechanical properties of SR/OD/P(St-MMA) composites were excellent when the microcapsules were coated with room temperature vulcanized silicone rubber (RTVSR), of which content was 2 phr (per hundred rubber). The enthalpy value of the composites was 67.6 J g-1 and the composites were found to have good energy storage function.

Novel in situ coordinated cerium salt/acrylonitrile-butadiene rubber composite

Energy Technology Data Exchange (ETDEWEB)

Han, Jianjun [Key Laboratory of Special Functional Aggregated Materials, Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Lu, Haifeng, E-mail: lhf@sdu.edu.cn [Key Laboratory of Special Functional Aggregated Materials, Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Zhang, Jie [Key Laboratory of Special Functional Aggregated Materials, Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Feng, Shengyu, E-mail: fsy@sdu.edu.cn [Key Laboratory of Special Functional Aggregated Materials, Ministry of Education, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)

2012-09-14

A novel rubber composite of acrylonitrile-butadiene rubber (NBR) filled with cerium salt particles was vulcanized via in situ coordination for the first time. The resulting materials exhibit good mechanical properties. Curing characteristics analysis, differential scanning calorimetry, X-ray photoelectron spectroscopy, tensile testing, and an equilibrium swelling method were used for the characterization of the composite. The results in this paper indicate that the composite is a kind of elastomer based on the in situ coordination crosslinking interactions between the nitrile groups (-CN) of NBR and cerium ions. The mechanical properties of vulcanized cerium salt/ NBR rubber are altered when changing the sorts of cerium salt. Moreover, these materials show good irradiation resistance because of the introduction of the cerium salt. -- Highlights: Black-Right-Pointing-Pointer Cerium salts were firstly used to vulcanize the acrylonitrile-butadiene rubber. Black-Right-Pointing-Pointer Cerium salts act as not only crosslink agents but also reinforcing fillers in the matrix. Black-Right-Pointing-Pointer These materials show good irradiation resistance and mechanical properties at same time.

A comparative study of gelatin and starch-based nano-composite films modified by nano-cellulose and chitosan for food packaging applications.

Science.gov (United States)

Noorbakhsh-Soltani, S M; Zerafat, M M; Sabbaghi, S

2018-06-01

Environmental concerns have led to extensive research for replacing polymer-based food packaging with bio-nano-composites. In this study, incorporation of nano-cellulose into gelatin and starch matrices is investigated for this purpose. Chitosan is used to improve mechanical, anti-fungal and waterproof properties. Experiments are designed and analyzed using response surface methodology. Nano-Cellulose is synthesized via acid hydrolysis and incorporated in base matrices through wet processing. Also, tensile strength test, food preservation, transparency in visible and UV and water contact angle are performed on the nano-composite films. DSC/TGA and air permeability tests are also performed on the optimal films. The results show that increasing nano-cellulose composition to 10% leads to increase the tensile strength at break to 8121 MN/m 2 and decrease the elongation at break. Also, increasing chitosan composition from 5% to 30% can enhance food preservation up to 15 days. Copyright © 2018 Elsevier Ltd. All rights reserved.

Electrical property and characterization of nano-SnO2/wollastonite composite materials

International Nuclear Information System (INIS)

Sun, Zhiming; Bai, Zhiqiang; Shen, Hongling; Zheng, Shuilin; Frost, Ray L.

2013-01-01

Graphical abstract: Resistivity as a function of different factors: hydrolysis temperature and time. Highlights: ► We have synthesized nano-tin oxide deposited on the surface of wollastonite. ► The antistatic properties were measured by rubber sheeter and four-point probe (FPP) sheet resistance measurement. ► The results showed that the nano-SnO 2 /wollastonite composite materials showed better antistatic properties. ► The surface of wollastonite fiber was coated with a layer of 10–15 nm thickness of tin oxide grains. - Abstract: Nano-tin oxide was deposited on the surface of wollastonite using the mixed solution including stannic chloride pentahydrate precursor and wollastonite by a hydrolysis precipitation process. The antistatic properties of the wollastonite materials under different calcined conditions and composite materials (nano-SnO 2 /wollastonite, SW) were measured by rubber sheeter and four-point probe (FPP) sheet resistance measurement. Effects of hydrolysis temperature and time, calcination temperature and time, pH value and nano-SnO 2 coating amount on the resistivity of SW powders were studied, and the optimum experimental conditions were obtained. The microstructure and surface properties of wollastonite, precipitate and SW were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS), specific surface area analyzer (BET), thermogravimetry (TG), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and Fourier translation infrared spectroscopy (FTIR) respectively. The results showed that the nano-SnO 2 /wollastonite composite materials under optimum preparation conditions showed better antistatic properties, the resistivity of which was reduced from 1.068 × 10 4 Ω cm to 2.533 × 10 3 Ω cm. From TG and XRD analysis, the possible mechanism for coating of SnO 2 nanoparticles on the surface of wollastonite was proposed. The infrared spectrum indicated

Organic/inorganic composite membranes based on polybenzimidazole and nano-SiO2

International Nuclear Information System (INIS)

Pu Hongting; Liu Lu; Chang Zhihong; Yuan Junjie

2009-01-01

Organic/inorganic composite membranes based on polybenzimidazole (PBI) and nano-SiO 2 were prepared in this work. However, the preparation of PBI/SiO 2 composite membrane is not easy since PBI is insoluble in water, while nano-SiO 2 is hydrophilic due to the hydrophilicity of nano-SiO 2 and water-insolubility of PBI. Thus, a solvent-exchange method was employed to prepare the composite membrane. The morphology of the composite membranes was studied by scanning electron microscopy (SEM). It was revealed that inorganic particles were dispersed homogenously in the PBI matrix. The thermal stability of the composite membrane is higher than that of pure PBI, both for doped and undoped membranes. PBI/SiO 2 composite membranes with up to 15 wt% SiO 2 exhibited improved mechanical properties compared with PBI membranes. The proton conductivity of the composite membranes containing phosphoric acid was studied. The nano-SiO 2 in the composite membranes enhanced the ability to trap phosphoric acid, which improved the proton conductivity of the composite membranes. The membrane with 15 wt% of inorganic material is oxidatively stable and has a proton conductivity of 3.9 x 10 -3 S/cm at 180 deg. C.

Characterization of fabricated cobalt-based alloy/nano bioactive glass composites

Energy Technology Data Exchange (ETDEWEB)

Bafandeh, Mohammad Reza, E-mail: mr.bafandeh@gmail.com [Department of Materials Science and Engineering, Faculty of Engineering, University of Kashan, Kashan (Iran, Islamic Republic of); Gharahkhani, Raziyeh; Fathi, Mohammad Hossein [Department of Materials Engineering, Isfahan University of Technology (IUT), Isfahan 84156-83111 (Iran, Islamic Republic of)

2016-12-01

In this work, cobalt-based alloy/nano bioactive glass (NBG) composites with 10, 15 and 20 wt% NBG were prepared and their bioactivity after immersion in simulated body fluid (SBF) for 1 to 4 weeks was studied. Scanning electron microscopy images of two- step sintered composites revealed relatively dense microstructure. The results showed that density of composite samples decreased with increase in NBG amount. The microstructure analysis as well as energy dispersive X-ray analysis (EDX) revealed that small amount of calcium phosphate phases precipitates on the surface of composite samples after 1 week immersion in SBF. After 2 weeks immersion, considerable amounts of cauliflower-like shaped precipitations were seen on the surface of the composites. Based on EDX analysis, these precipitations were composed mainly from Ca, P and Si. The observed bands in the Fourier transform infrared spectroscopy of immersed composites samples for 4 weeks in SBF, were characteristic bands of hydroxyapatite. Therefore it is possible to form hydroxyapatite layer on the surface of composite samples during immersion in SBF. The results indicated that prepared composites unlike cobalt-based alloy are bioactive, promising their possibility for implant applications. - Highlights: • Co-based alloy/nano bioactive glass (NBG) composites with 10, 15 and 20 wt% NBG were prepared. • In order to study their bioactivity, composite samples were immersed in SBF solution for 1 to 4 weeks. • Immersion in SBF accompanied with precipitation of hydroxyapatite on surface of samples. • Prepared composite samples unlike cobalt-based alloy were bioactive.

Characterization of fabricated cobalt-based alloy/nano bioactive glass composites

International Nuclear Information System (INIS)

Bafandeh, Mohammad Reza; Gharahkhani, Raziyeh; Fathi, Mohammad Hossein

2016-01-01

In this work, cobalt-based alloy/nano bioactive glass (NBG) composites with 10, 15 and 20 wt% NBG were prepared and their bioactivity after immersion in simulated body fluid (SBF) for 1 to 4 weeks was studied. Scanning electron microscopy images of two- step sintered composites revealed relatively dense microstructure. The results showed that density of composite samples decreased with increase in NBG amount. The microstructure analysis as well as energy dispersive X-ray analysis (EDX) revealed that small amount of calcium phosphate phases precipitates on the surface of composite samples after 1 week immersion in SBF. After 2 weeks immersion, considerable amounts of cauliflower-like shaped precipitations were seen on the surface of the composites. Based on EDX analysis, these precipitations were composed mainly from Ca, P and Si. The observed bands in the Fourier transform infrared spectroscopy of immersed composites samples for 4 weeks in SBF, were characteristic bands of hydroxyapatite. Therefore it is possible to form hydroxyapatite layer on the surface of composite samples during immersion in SBF. The results indicated that prepared composites unlike cobalt-based alloy are bioactive, promising their possibility for implant applications. - Highlights: • Co-based alloy/nano bioactive glass (NBG) composites with 10, 15 and 20 wt% NBG were prepared. • In order to study their bioactivity, composite samples were immersed in SBF solution for 1 to 4 weeks. • Immersion in SBF accompanied with precipitation of hydroxyapatite on surface of samples. • Prepared composite samples unlike cobalt-based alloy were bioactive.

Enhanced Removal of Trichloroethylene in Water Using Nano-ZnO/Polybutadiene Rubber Composites

Directory of Open Access Journals (Sweden)

Dae Gyu Jang

2016-09-01

Full Text Available An innovative nanoscale ZnO/polybutadiene rubber composite (ZBRC was developed as a valid alternative to TiO2 particles or immobilized TiO2 for the mineralization of chlorinated hydrocarbons without difficulties in the recovery of nanoscale photocatalyst particles. A synergistic increase in the removal of 1,1,2-trichloroethylene (TCE through the coupled reaction processes (i.e., sorption, photolysis, and photocatalysis was observed because sorption of TCE to the ultraviolet(UV-transparent polybutadiene rubber occurred, and was coupled with the heterogeneous photocatalytic reactions with nanoscale ZnO particles on the surface of ZBRC. The removal rate of TCE decreased with an increase in the initial concentration of TCE because of both inhibited generation of electron–hole pairs and deficiency of photons to activate ZnO particles. Also, the TCE removal rate increased as the loading amount of ZBRC increased. Based on satisfactory linear regressions (R2 ≥ 0.94 between the apparent degradation rate constant (Kapp and the initial concentration vs. the ZBRC loading amount, the Kapp values can be estimated, a priori, without performing photocatalytic experiments. The removal efficiencies were more significantly affected by the changes in the initial concentration of TCE and the ZBRC loading amounts than by the changes in light intensity and pH in aqueous solutions. From the results of response surface analysis, the greater removal efficiencies of TCE were achieved with higher pH values, greater amounts of ZBRC, and greater intensity of light. Based on these results, newly-developed ZBRC with both high removal efficiency and low cost performs as a valid alternative to TiO2 particles or immobilized TiO2 for the mineralization of chlorinated hydrocarbons in various environmental and industrial matrices.

Morphological and mechanical properties of styrene butadiene rubber/nano copper nanocomposites

Science.gov (United States)

Harandi, Maryam Hadizadeh; Alimoradi, Fakhrodin; Rowshan, Gholamhussein; Faghihi, Morteza; Keivani, Maryam; Abadyan, Mohamadreza

In this research, rubber based nanocomposites with presence of nanoparticle has been studied. Styrene butadiene rubber (SBR)/nanocopper (NC) composites were prepared using two-roll mill method. Transmission electron microscope (TEM) and scanning electron microscope (SEM) images showed proper dispersion of NC in the SBR matrix without substantial agglomeration of nanoparticles. To evaluate the curing properties of nanocomposite samples, swelling and cure rheometric tests were conducted. Moreover, the rheological studies were carried out over a range of shear rates. The effect of NC particles was examined on the thermal behavior of the SBR using thermal gravimetric analysis (TGA). Furthermore, tensile tests were employed to investigate the capability of nanoparticles to enhance mechanical behavior of the compounds. The results showed enhancement in tensile properties with incorporation of NC to SBR matrix. Moreover, addition of NC increased shear viscosity and curing time of SBR composites.

Electrical property and characterization of nano-SnO{sub 2}/wollastonite composite materials

Energy Technology Data Exchange (ETDEWEB)

Sun, Zhiming [School of Chemical and Environmental Engineering, China University of Mining and Technology, Beijing 100083 (China); Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, 2 George Street, GPO Box 2434, Brisbane, Queensland 4001 (Australia); Bai, Zhiqiang; Shen, Hongling [Qinhuangdao Glass Research Design Institute, Qinhuangdao 066000 (China); Zheng, Shuilin, E-mail: shuilinzh@yahoo.com.cn [School of Chemical and Environmental Engineering, China University of Mining and Technology, Beijing 100083 (China); Frost, Ray L., E-mail: r.frost@qut.edu.au [Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, 2 George Street, GPO Box 2434, Brisbane, Queensland 4001 (Australia)

2013-03-15

Graphical abstract: Resistivity as a function of different factors: hydrolysis temperature and time. Highlights: ► We have synthesized nano-tin oxide deposited on the surface of wollastonite. ► The antistatic properties were measured by rubber sheeter and four-point probe (FPP) sheet resistance measurement. ► The results showed that the nano-SnO{sub 2}/wollastonite composite materials showed better antistatic properties. ► The surface of wollastonite fiber was coated with a layer of 10–15 nm thickness of tin oxide grains. - Abstract: Nano-tin oxide was deposited on the surface of wollastonite using the mixed solution including stannic chloride pentahydrate precursor and wollastonite by a hydrolysis precipitation process. The antistatic properties of the wollastonite materials under different calcined conditions and composite materials (nano-SnO{sub 2}/wollastonite, SW) were measured by rubber sheeter and four-point probe (FPP) sheet resistance measurement. Effects of hydrolysis temperature and time, calcination temperature and time, pH value and nano-SnO{sub 2} coating amount on the resistivity of SW powders were studied, and the optimum experimental conditions were obtained. The microstructure and surface properties of wollastonite, precipitate and SW were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS), specific surface area analyzer (BET), thermogravimetry (TG), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and Fourier translation infrared spectroscopy (FTIR) respectively. The results showed that the nano-SnO{sub 2}/wollastonite composite materials under optimum preparation conditions showed better antistatic properties, the resistivity of which was reduced from 1.068 × 10{sup 4} Ω cm to 2.533 × 10{sup 3} Ω cm. From TG and XRD analysis, the possible mechanism for coating of SnO{sub 2} nanoparticles on the surface of wollastonite was proposed

Degrading radiation effects on properties of bromobutyl rubber compounds

Energy Technology Data Exchange (ETDEWEB)

Scagliusi, Sandra R.; Cardoso, Elisabeth C.L.; Pozenato, Cristina A.; Lugao, Ademar B., E-mail: srscagliusi@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

The understanding of chemistry involved in degradation induced radiation is becoming more and more relevant in the re-use of polymeric materials, as well in beneficial radiation uses. Degrading radiation effects have been considered from viewpoint of controlled degradation for isoprene/isobutene in rubbers for recycling purposes. Bromobutyl rubber (BIIR) is an isobutylene/isoprene copolymer comprising 1.9 to 2.1% bromine and has a lot of applications including in tires air-chambers. In this work there were evaluated gamma-irradiation effects for re-use or recycling objectives in elastomeric bromobutyl compositions irradiated at 5, 15, 25, 50, 100,150 and 200 kGy. Mechanical properties, hardness and swelling were assessed in non-vulcanized and vulcanized rubber, non-irradiated and irradiated at different doses. The major gamma radiation effect in butyl rubber is the generation of free radicals along changes in mechanical properties. Irradiation effects in bromobutyl rubber compounds were comprehensively investigated, demonstrated and discussed. (author)

Degrading radiation effects on properties of bromobutyl rubber compounds

International Nuclear Information System (INIS)

Scagliusi, Sandra R.; Cardoso, Elisabeth C.L.; Pozenato, Cristina A.; Lugao, Ademar B.

2013-01-01

The understanding of chemistry involved in degradation induced radiation is becoming more and more relevant in the re-use of polymeric materials, as well in beneficial radiation uses. Degrading radiation effects have been considered from viewpoint of controlled degradation for isoprene/isobutene in rubbers for recycling purposes. Bromobutyl rubber (BIIR) is an isobutylene/isoprene copolymer comprising 1.9 to 2.1% bromine and has a lot of applications including in tires air-chambers. In this work there were evaluated gamma-irradiation effects for re-use or recycling objectives in elastomeric bromobutyl compositions irradiated at 5, 15, 25, 50, 100,150 and 200 kGy. Mechanical properties, hardness and swelling were assessed in non-vulcanized and vulcanized rubber, non-irradiated and irradiated at different doses. The major gamma radiation effect in butyl rubber is the generation of free radicals along changes in mechanical properties. Irradiation effects in bromobutyl rubber compounds were comprehensively investigated, demonstrated and discussed. (author)

Identification of volatile butyl rubber thermal-oxidative degradation products by cryofocusing gas chromatography/mass spectrometry (cryo-GC/MS).

Energy Technology Data Exchange (ETDEWEB)

Smith, Jonell Nicole; White, Michael Irvin; Bernstein, Robert; Hochrein, James Michael

2013-02-01

Chemical structure and physical properties of materials, such as polymers, can be altered as aging progresses, which may result in a material that is ineffective for its envisioned intent. Butyl rubber formulations, starting material, and additives were aged under thermal-oxidative conditions for up to 413 total days at up to 124 ÀC. Samples included: two formulations developed at Kansas City Plant (KCP) (#6 and #10), one commercially available formulation (#21), Laxness bromobutyl 2030 starting material, and two additives (polyethylene AC-617 and Vanax MBM). The low-molecular weight volatile thermal-oxidative degradation products that collected in the headspace over the samples were preconcentrated, separated, and detected using cryofocusing gas chromatography mass spectrometry (cryo-GC/MS). The majority of identified degradation species were alkanes, alkenes, alcohols, ketones, and aldehydes. Observations for Butyl #10 aged in an oxygen-18 enriched atmosphere (18O2) were used to verify when the source of oxygen in the applicable degradation products was from the gaseous environment rather than the polymeric mixture. For comparison purposes, Butyl #10 was also aged under non-oxidative thermal conditions using an argon atmosphere.

Properties of Natural Rubber-Based Composites Containing Fullerene

Directory of Open Access Journals (Sweden)

Omar A. Al-Hartomy

2012-01-01

Full Text Available In this study the influence of fullerenes in concentrations from 0.5 to 1.5 phr on both the vulcanization characteristics of the compounds and physicomechanical, dynamic, and dielectric properties and thermal aging resistance of nanocomposites on the basis of natural rubber has been investigated. The effect of the filler dispersion in the elastomeric matrix has been also investigated. Neat fullerene and the composites comprising it have been studied and characterized by scanning electron microscopy (SEM and transmission electron microscopy (TEM.

Comparison of the mechanical properties between carbon nanotube and nanocrystalline cellulose polypropylene based nano-composites

International Nuclear Information System (INIS)

Huang, Jun; Rodrigue, Denis

2015-01-01

Highlights: • SWCNT and NCC can effectively improve the mechanical properties of nano-composites. • SWCNT is more effective than NCC to increase modulus and strength. • Longer NCC is more effective to improve the mechanical properties of nano-composites. • It is more economic to use NCC than SWCNT to improve mechanical properties. - Abstract: Using beam and tetrahedron elements to simulate nanocrystalline cellulose (NCC), single wall carbon nanotube (SWCNT) and polypropylene (PP), finite element method (FEM) is used to predict the mechanical properties of nano-composites. The bending, shear and torsion behaviors of nano-composites are especially investigated due to the limited amount of information in the present literature. First, mixed method (MM) and FEM are used to compare the bending stiffness of NCC/PP and SWCNT/PP composites. Second, based on mechanics of materials, the shear moduli of both types of nano-composites are obtained. Finally, fixing the number of fibers and for different volume contents, four NCC lengths are used to determine the mechanical properties of the composites. The bending and shearing performances are also compared between NCC and SWCNT based composites. In all cases, the elastic–plastic analyses are carried out and the stress or strain distributions for specific regions are also investigated. From all the results obtained, an economic analysis shows that NCC is more interesting than SWCNT to reinforce PP

A review on mechanical properties of magnesium based nano composites

Science.gov (United States)

Tarafder, Nilanjan; Prasad, M. Lakshmi Vara

2018-04-01

A review was done on Magnesium (Mg) based composite materials reinforced with different nano particles such as TiO2, Cu, Y2O3, SiC, ZrO2 and Al2O3. TiO2 and Al2O3 nanoparticles were synthesised by melt deposition process. Cu, Y2O3, SiC and ZrO2 nanoparticles were synthesised by powder metallurgy process. Composite microstructural characteristics shows that the nano-size reinforcements are uniformly distributed in the composite matrix and also minimum porosity with solid interfacial integrity. The mechanical properties showed yield strength improvement by 0.2 percentage and Ultimate tensile strength (UTS) was also improved for all the nano-particles. But UTS was adversely affected with TiO2 reinforcement while ductility was increased. With Cu reinforcement elastic modulus, hardness and fracture resistance increased and improved the co-efficient of thermal expansion (CTE) of Mg based matrix. By Y2O3 reinforcement hardness, fracture resistance was improved and ductility reached maximum by 0.22 volume percentage of Y2O3 and decreased with succeeding increase in Y2O3 reinforcement. The readings exposed that mechanical properties were gathered from the composite comprising 2.0 weight percentage of Y2O3. Ductility and fracture resistance increased with ZrO2 reinforcement in Mg matrix. Using Al2O3 as reinforcement in Mg composite matrix hardness, elastic modulus and ductility was increased but porosity reduced with well interfacial integrity. Dissipation of energy in the form of damping capacity was resolved by classical vibration theory. The result showed that an increasing up to 0.4 volume percentage alumina content increases the damping capacity up to 34 percent. In another sample, addition of 2 weight percentage nano-Al2O3 particles showed big possibility in reducing CTE from 27.9-25.9×10-6 K-1 in Magnesium, tensile and yield strength amplified by 40MPa. In another test, Mg/1.1Al2O3 nanocomposite was manufactured by solidification process followed by hot extrusion

Natural rubber/high density polyethylene/ground rubber composites vulcanized by gamma irradiation

International Nuclear Information System (INIS)

Shaltout, N.A.; Abou zeid, M.M.; Khalil, A.M.; El Miligy, A.A.

2010-01-01

Natural rubber (NR) was blended mechanically with 50 phr high density polyethylene (HDPE). the mechanical, physical and thermal properties of NR/HDPE blend and its composites with different contents of ground tire rubber (GTR) before and after exposure to gamma irradiation to various doses up to 250 kGy were studied. Also, the change in structure morphology of irradiated NR/HDPE blend as well as NR/HDPE/GTR composites was examined by scanning electron microscope (SEM). The results showed that the substitution of a part of virgin NR with GTR decreases the mechanical and physical properties but not to the extent of deterioration . However, it was found that the mechanical and physical properties were improved after gamma irradiation . Composite of NR/GTR/HDPE (75/25/50) showed good properties. Scanning electron microscope showed homogeneity between the irradiated composites ingredients.

The role of linked phospholipids in the rubber-filler interaction in carbon nanotube (CNT) filler natural rubber (NR) composites

NARCIS (Netherlands)

Le, H.H.; Abhijeet, S.; Ilish, S.; Klehm, J.; Henning, S.; Beiner, M.; Sarkawi, S.S.; Dierkes, Wilma K.; Das, A.; Fischer, D.; Stöckelhuber, K.-W.; Wiessner, S.; Khatiwada, S.P.; Adhikari, R.; Pham, T.; Heinrich, G.; Radusch, H.-J.

2014-01-01

The aim of the present work is to evidence the role of the linked phospholipids of natural rubber (NR) in the rubber-carbon nanotube (CNT) interactions in rubber composites. Three rubbers namely NR, deproteinized NR (DPNR) and a synthetic rubber isoprene (IR) were used as matrix for CNTs. The

Fate and effect of tire rubber ash nano-particles (RANPs) in cucumber.

Science.gov (United States)

Moghaddasi, Sahar; Hossein Khoshgoftarmanesh, Amir; Karimzadeh, Fatholah; Chaney, Rufus

2015-05-01

There are growing interests on effects of nano-materials on living organisms including higher plants. No report is available on positive and negative effects of rubber ash nano-particles (RANPs) on edible plants. Recently, we reported the possibility of using waste tire rubber and rubber ash as zinc (Zn) fertilizer for plants. In this nutrient solution culture study, for the first time, root uptake and the effects of RANPs on growth and Zn, cadmium (Cd), and lead (Pb) concentration in cucumber was investigated. Various Zn levels (0, 1, 5, 25, 125mgL(-1)) were applied in the form of RANPs or ZnSO4. The root RANPs uptake was visualized by light (LA), scanning electron (SEM), and transmission electron microcopies (TEM). At all Zn levels, cucumber plants supplied with RANPs produced higher shoot and root biomass compared with those supplied with ZnSO4. In addition, the RANPs resulted in higher accumulation of Zn in cucumber tissues in comparison with ZnSO4; although phytotoxicity of Zn from ZnSO4 was greater than that from RANPs. Clear evidence of the RANPs penetration into the root cells was obtained by using SEM and TEM. Filaments of RANPs were also observed at the end of roots by LM and TEM. Further research is needed to clarify the fate of the RANPs in plant cells and their possible risks for food chain. Copyright © 2015 Elsevier Inc. All rights reserved.

[Total analysis of organic rubber additives].

Science.gov (United States)

He, Wen-Xuan; Robert, Shanks; You, Ye-Ming

2010-03-01

In the present paper, after middle pressure chromatograph separation using both positive phase and reversed-phase conditions, the organic additives in ethylene-propylene rubber were identified by infrared spectrometer. At the same time, by using solid phase extraction column to maintain the main component-fuel oil in organic additves to avoid its interfering with minor compounds, other organic additves were separated and analysed by GC/Ms. In addition, the remaining active compound such as benzoyl peroxide was identified by CC/Ms, through analyzing acetone extract directly. Using the above mentioned techniques, soften agents (fuel oil, plant oil and phthalte), curing agent (benzoylperoxide), vulcanizing accelerators (2-mercaptobenzothiazole, ethyl thiuram and butyl thiuram), and antiagers (2, 6-Di-tert-butyl-4-methyl phenol and styrenated phenol) in ethylene-propylene rubber were identified. Although the technique was established in ethylene-propylene rubber system, it can be used in other rubber system.

Nano-composite materials

Science.gov (United States)

Lee, Se-Hee; Tracy, C. Edwin; Pitts, J. Roland

2010-05-25

Nano-composite materials are disclosed. An exemplary method of producing a nano-composite material may comprise co-sputtering a transition metal and a refractory metal in a reactive atmosphere. The method may also comprise co-depositing a transition metal and a refractory metal composite structure on a substrate. The method may further comprise thermally annealing the deposited transition metal and refractory metal composite structure in a reactive atmosphere.

Particle reinforced composites from acrylamide modified blend of styrene-butadiene and natural rubber

Science.gov (United States)

Blends of styrene-butadiene rubber and natural rubber that provide balanced properties were modified with acrylamide and reinforced with soy protein particles. The rubber composites show improved mechanical properties. Both modified rubber and composites showed a faster curing rate. The crosslinking...

In situ self-polymerization of unsaturated metal methacrylate and its dispersion mechanism in rubber-based composites

Energy Technology Data Exchange (ETDEWEB)

Wen, Shipeng; Zhou, Yao; Yao, Lu [State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Zhang, Liqun [State Key Laboratory of Organic-Inorganic Composites, Beijing University of Chemical Technology, Beijing 100029 (China); Chan, Tung W. [Department of Materials Science and Engineering, Virginia Polytechnic Institute and State University, VA 24061 (United States); Liang, Yongri [Beijing National Laboratory for Molecular Sciences, Joint Laboratory of Polymer Science and Materials, Institute of Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); Liu, Li, E-mail: LiuL@mail.buct.edu.cn [State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology, Beijing 100029 (China)

2013-11-10

Highlights: • In situ self-polymerization of unsaturated metal methacrylate was investigated mainly by the thermal effect. • UMM with low melting point can self-polymerize to a large extent. • The fine dispersion phase is composed of poly(UMM) nanoparticles formed by in situ self-polymerization in the rubber matrix. • The UMM crystals in the presence of peroxide and rubber undergo the processes of melting, diffusion, polymerization, and phase separation in this order. - Abstract: Unsaturated metal methacrylate (UMM) as one kind of functional filler has played an important role in reinforcing rubber materials. The in situ self-polymerization of UMM in UMM/rubber composite leads to the uniform dispersion of poly(UMM) in the rubber matrix, while the crosslinking of rubber and grafting between UMM and rubber chains occur simultaneously, making it difficult to clarify the effect of the in situ polymerization on the dispersion of poly(UMM) in the rubber matrix. In this work, we investigated the dispersion mechanism of UMM without rubber matrix for the first time using differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy. Three types of UMMs including zinc methacrylate (Zn(MA){sub 2}), sodium methacrylate (Na(MA)) and samarium methacrylate (Sm(MA){sub 3}) were chosen to investigate the in situ self-polymerization of UMM. Based on DSC results, we conclude that the crystals with low melting point tend to self-polymerize first and generate a large amount of heat in the presence of peroxide. The high heat of reaction can melt the crystals with high melting point, and more UMM molecules are dissolved in the rubber matrix, thus increasing the extent of the in situ polymerization. Hence, the UMM with low melting point can self-polymerize to a large extent. Our findings provide in-depth understanding of the dispersion mechanism of UMM in rubber.

In situ self-polymerization of unsaturated metal methacrylate and its dispersion mechanism in rubber-based composites

International Nuclear Information System (INIS)

Wen, Shipeng; Zhou, Yao; Yao, Lu; Zhang, Liqun; Chan, Tung W.; Liang, Yongri; Liu, Li

2013-01-01

Highlights: • In situ self-polymerization of unsaturated metal methacrylate was investigated mainly by the thermal effect. • UMM with low melting point can self-polymerize to a large extent. • The fine dispersion phase is composed of poly(UMM) nanoparticles formed by in situ self-polymerization in the rubber matrix. • The UMM crystals in the presence of peroxide and rubber undergo the processes of melting, diffusion, polymerization, and phase separation in this order. - Abstract: Unsaturated metal methacrylate (UMM) as one kind of functional filler has played an important role in reinforcing rubber materials. The in situ self-polymerization of UMM in UMM/rubber composite leads to the uniform dispersion of poly(UMM) in the rubber matrix, while the crosslinking of rubber and grafting between UMM and rubber chains occur simultaneously, making it difficult to clarify the effect of the in situ polymerization on the dispersion of poly(UMM) in the rubber matrix. In this work, we investigated the dispersion mechanism of UMM without rubber matrix for the first time using differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy. Three types of UMMs including zinc methacrylate (Zn(MA) 2 ), sodium methacrylate (Na(MA)) and samarium methacrylate (Sm(MA) 3 ) were chosen to investigate the in situ self-polymerization of UMM. Based on DSC results, we conclude that the crystals with low melting point tend to self-polymerize first and generate a large amount of heat in the presence of peroxide. The high heat of reaction can melt the crystals with high melting point, and more UMM molecules are dissolved in the rubber matrix, thus increasing the extent of the in situ polymerization. Hence, the UMM with low melting point can self-polymerize to a large extent. Our findings provide in-depth understanding of the dispersion mechanism of UMM in rubber

Molecular Diffusion of Toluene through CaCO3-Filled Natural Rubber Composites

Directory of Open Access Journals (Sweden)

Hedayatollah Sadeghi Ghari

2012-12-01

Full Text Available The transport properties of liquids and gases through polymeric materialsplay a very important role in some areas of industrial applications. In thisstudy, natural rubber (NR/CaCO3 composites were prepared by melt mixingmethod. By equilibrium swelling test, the transport process of toluene in the prepared natural rubber composites was investigated. The diffusion and transport of toluene through calcium carbonate-filled natural rubber composites have been studied in the temperature range 25–45°C. The diffusion of toluene through these composites was studied with special reference to the effect of filler concentration and temperature.The transport coefficients such as diffusion, permeation and sorption coefficients were estimated from the swelling data. To find out the mechanism of diffusion in prepared composites, the results of swelling studies were applied to an empirical equation. In these composites, diffusion is approximately based on Fickian diffusion mechanism and by increases in temperature; diffusion mechanism is more close to Fickian mechanism. Increase of filler content in composite would result in decreased ultimateswelling and slower diffusion rate of solvent. The diffusion rate, diffusion coefficient and the permeability increased by temperature. The study of the diffusion of toluene through filled natural rubber indicated that the concentration of filler plays an important role in the diffusion, sorption and permeation coefficients. Also interfacial interactions in NR composites were checked by dynamic-mechanical analysis. The microstructure and dispersion of calcium carbonate particles in natural rubber matrix were studiedby field emission scanning electron microscopy (FE-SEM. In general, the results of swelling tests, dynamic-mechanical analysis and FE-SEM images show that the optimized value of filler in NR composites is equal to 10 phr calcium carbonate.

Preparation and Characterization of Graphene-Based Magnetic Hybrid Nano composite

International Nuclear Information System (INIS)

Jashiela Wani Jusin; Madzlan Aziz

2016-01-01

Graphene-based magnetic hybrid nano composite has the advantage of exhibiting better performance as platform or supporting materials to develop novel properties of composite by increasing selectivity of the targeted adsorbate. The hybrid nano material was prepared by mixing and hydrolysing iron (II) and iron (III) salt precursors in the presence of GO dispersion through coprecipitation method followed by in situ chemical reduction of GO. The effect of weight loading ratio of Fe to GO (4:1, 2.5:1, 1:1 and 1:4) on structural properties of the hybrid nano materials was investigated. The presence of characteristic peaks in FTIR spectra indicated that GO has been successfully oxidized from graphite while the decrease in oxygenated functional groups and peaks intensity evidenced the formation of hybrid nano materials through the subsequent reduction process. The presence of characteristic peaks in XRD pattern denoted that magnetite nanoparticles disappeared at higher loading of GO. TEM micrograph showed that the best distribution of iron oxide particles on the surface of hybrid nano material occurred when the loading ratio of Fe to GO was fixed at 2:5 to 1. The reduced graphene oxide (RGO) sheets in the hybrid materials showed less wrinkled sheet like structure compared to GO due to exfoliation and reduction process during the synthesis. The layered morphology of GO degrades at higher concentrations of iron oxide. (author)

Swelling behaviour of isora/natural rubber composites in oils used

Indian Academy of Sciences (India)

Natural rubber/isora fibre composites were cured at various temperatures. The solvent swelling characteristics of natural rubber composites containing both untreated and alkali treated fibres were investigated in aromatic and aliphatic solvents like toluene, and -hexane. The diffusion experiments were conducted by the ...

Mechanical characterization of scalable cellulose nano-fiber based composites made using liquid composite molding process

Science.gov (United States)

Bamdad Barari; Thomas K. Ellingham; Issam I. Ghamhia; Krishna M. Pillai; Rani El-Hajjar; Lih-Sheng Turng; Ronald Sabo

2016-01-01

Plant derived cellulose nano-fibers (CNF) are a material with remarkable mechanical properties compared to other natural fibers. However, efforts to produce nano-composites on a large scale using CNF have yet to be investigated. In this study, scalable CNF nano-composites were made from isotropically porous CNF preforms using a freeze drying process. An improvised...

Evaluation of rubber composites as shielding materials against ionizing radiation

International Nuclear Information System (INIS)

Atia, M.K.

2010-01-01

Styrene-butadiene rubber/lead oxide composites were prepared as γ-radiation shields.The composites were prepared with different concentration of red lead oxide (Pb 3 O 4 ) .The assessment of the linear attenuation coefficient of the SBR/lead oxide composites for γ -rays from 137 Cs 137 γ-radiation point source was studied . The factors affecting the mechanical properties and shielding capacity of the composites were also studied. These factors include the lead oxide concentration, the type of monomers added and the irradiation dose. The styrene-butadiene rubber/lead oxide composites can attain up to about 43% of the shielding capacity of pure lead. The incorporation of high concentrations of lead oxide and the effect of accumulative irradiation doses up to 3000 kGy on the physico-mechanical properties of the composites were studied . These led to hardening of the SBR rubber/lead oxide composites.

Effect of gamma irradiation conditions on the radiation-induced degradation of isobutylene-isoprene rubber

Energy Technology Data Exchange (ETDEWEB)

Sen, M. E-mail: msen@hacettepe.edu.tr; Uzun, C.; Kantoglu, Oe.; Erdogan, S.M.; Deniz, V.; Gueven, O

2003-08-01

The effect of gamma irradiation conditions on the radiation-induced degradation of uncrosslinked, commercial isobutylene-isoprene rubbers has been investigated in this study. Influence of dose rate and irradiation atmosphere on the degradation of butyl rubber has been followed by viscosimetric and chromatographic analyses. Limiting viscosity number of all butyl rubbers decreased sharply up to 100 kGy and leveled off at around the same molecular weight, independent of dose rate. Slightly higher decrease in viscosity was observed for samples irradiated in air than in nitrogen especially at low dose rate irradiation. Cross-linking G(X), and chain scission G(S) yields of butyl rubbers were calculated by using weight- and number-average molecular weights of irradiated rubber determined by Size Exclusion Chromatography analyses. G-value results showed that chain scission reactions in isobutylene-isoprene rubber in air atmosphere are more favorable than in nitrogen atmosphere, and that lower dose rate enhances chain scission over cross-linking.

Tribological Properties of Silicone Rubber-Based Ceramizable Composites Destined for Wire Covers. Part I. Studies of Block-On-Ring Friction Contact

Directory of Open Access Journals (Sweden)

R. Anyszka

2015-06-01

Full Text Available Ceramizable composites of silicone rubber matrix become more and more popular materials destined for wire covers, what can enhance fire safety of building increasing operation time of important equipment or devices (eg fire sprinklers, elevators, alarms etc. Aim of the research was to examine tribological properties and wear of commercially available silicone rubber-based ceramizable composites against steel, in configuration – steel block on composite ring, under various load (5, 10, 15, 20, 25 and 30 N. Changes to friction force in time were monitored by a tribotester, whereas wear of the composite surfaces were determined using an optical microscope. Performed studies demonstrate, that tribological characteristics and wear of the composites depend significantly on the origin of material.

Flexural Properties of Activated Carbon Filled Epoxy Nano composites

International Nuclear Information System (INIS)

Khalil, H.P.S.A.; Khalil, H.P.S.A.; Alothman, O.Y.; Paridah, M.T.; Zainudin, E.S.

2014-01-01

Activated carbon (AC) filled epoxy nano composites obtained by mixing the desired amount of nano AC viz., bamboo stem, oil palm empty fruit bunch, and coconut shell from agricultural biomass with the epoxy resin. Flexural properties of activated carbons filled epoxy nano composites with 1 %, and 5 % filler loading were measured. In terms of flexural strength and modulus, a significant increment was observed with addition of 1 % vol and 5 % vol nano-activated carbon as compared to neat epoxy. The effect of activated carbon treated by two chemical agents (potassium hydroxide and phosphoric acid) on the flexural properties of epoxy nano composites were also investigated. Flexural strength of activated carbon-bamboo stem, activated carbon-oil palm, and activated carbon-coconut shell reinforced epoxy nano composites showed almost same value in case of 5 % potassium hydroxide activated carbon. Flexural strength of potassium hydroxide activated carbon-based epoxy nano composites was higher than phosphoric acid activated carbon. The flexural toughness of both the potassium hydroxide and phosphoric acid activated carbon reinforced composites range between 0.79 - 0.92 J. It attributed that developed activated carbon filled epoxy nano composites can be used in different applications. (author)

Functional properties of extruded nano composites based on cassava starch, polyvinyl alcohol and montmorillonite

International Nuclear Information System (INIS)

Debiagi, Flavia; Mali, Suzana

2011-01-01

The objectives of this work were to produce expanded nano composites (foams) based on starch, PVA and sodium montmorillonite and characterize them according to their expansion index (EI), density, water absorption capacity (WSC), mechanical properties and X-ray diffraction. The nano composites were prepared in a single-screw extruder using different starch contents (97.6 - 55.2 g/100 g formulation), PVA (0 - 40 g/100 g formulation), unmodified nano clay - Closite - Na (0 - 4. 8 g/100 g formulation) and glycerol (20 g/100 g formulation) as plasticizer. The addition of montmorillonite and PVA resulted in an increase of EI and a decrease of density of the samples, and reduced WSC and increased the mechanical strength of the foams. Through the analysis of X-ray diffraction can be observed that the addition of montmorillonite led to production of intercalated nano composites in all samples. (author)

Structural and physico-mechanical properties of natural rubber/GTR composites devulcanized by microwaves: influence of GTR source and irradiation time

OpenAIRE

Colom Fajula, Xavier; Marin-Genesca, Marc; Mujal Rosas, Ramón María; Formela, Krzysztof; Cañavate Ávila, Francisco Javier

2018-01-01

Ground tire rubber from car and truck was modified using microwave irradiation at variable time. The irradiated ground tire rubber was used as filler in composites based on natural rubber. The composites, with high content of ground tire rubber, were prepared using an internal batch mixer and subsequently cross-linked at 160¿. The influence of the ground tire rubber source (car/truck) and irradiation time on structure, physico-mechanical behaviour, thermal properties and morphology of natural...

Effects of Thermal and Humidity Aging on the Interfacial Adhesion of Polyketone Fiber Reinforced Natural Rubber Composites

Directory of Open Access Journals (Sweden)

Han Ki Lee

2016-01-01

Full Text Available Polyketone fiber is considered as a reinforcement of the mechanical rubber goods (MRG such as tires, automobile hoses, and belts because of its high strength and modulus. In order to apply it to those purposes, the high adhesion of fiber/rubber interface and good sustainability to aging conditions are very important. In this study, polyketone fiber reinforced natural rubber composites were prepared and they were subjected to thermal and humidity aging, to assess the changes of the interfacial adhesion and material properties. Also, the effect of adhesive primer treatment, based on the resorcinol formaldehyde resin and latex (RFL, of polyketone fiber for high interfacial adhesion was evaluated. Morphological and property changes of the rubber composites were analyzed by using various instrumental analyses. As a result, the rubber composite was aged largely by thermal aging at high temperature rather than humidity aging condition. Interfacial adhesion of the polyketone/NR composites was improved by the primer treatment and its effect was maintained in aging conditions.

Experimental and numerical studies on the sensitivity of carbon fibre/silicone rubber composite sensors

International Nuclear Information System (INIS)

Yang, Lili; Ge, Yong; Zhu, Qinghua; Zhang, Ce; Wang, Zongpeng; Liu, Penghuan

2012-01-01

Flexible conductive composite sensors are of great importance for applications in structural monitoring due to their low cost, high durability and excellent compatibility. In this work, carbon fibre/silicone rubber composites were prepared and their sensitivity near the percolation threshold was investigated experimentally and theoretically. Results show that carbon fibre/silicone rubber composites have great mechanical and sensitivity even under high strain conditions. Two models based on the tunnelling effect and general effective medium theory were found to understand the sensitivity of composites with lower and higher fractions of carbon fibre. Moreover, the reversibility of the sensing performance is improved with the increase of carbon fibre addition. (paper)

Effect of organo-clay on the dielectric relaxation response of silicone rubber

International Nuclear Information System (INIS)

Gharavi, N; Razzaghi-Kashani, M; Golshan-Ebrahimi, N

2010-01-01

Dielectric elastomers are light weight, low-cost, highly deformable and fast response smart materials capable of converting electrical energy into mechanical work or vice versa. Silicone rubber is a well-known dielectric elastomer which is used as actuator, and in order to enhance the efficiency of this smart material, compounding of silicone rubber with various fillers can be carried out. The effect of organically modified montmorillonite (OMMT) nano-clay on improvement of dielectric properties, actuation stress and its relaxation response was considered in this study. OMMT was dispersed in room temperature vulcanized (RTV) silicone rubber, and a composite film was cast. Using an in-house actuation set-up, it was shown that the actuation stress for a given electric field intensity is higher for composites than that for pristine silicone rubber. Also, the time-dependent actuation response of the samples was evaluated, and it was shown that the characteristic relaxation time of the actuation stress for composites is less than for the pristine rubber as a result of OMMT addition

Preparation, Characterization, and Modeling of Carbon Nano fiber/Epoxy Nano composites

International Nuclear Information System (INIS)

Sun, L.H.; Yang, Z.G.; Ounaies, Z.; Whalen, C.A.; Gao, X.L.

2011-01-01

There is a lack of systematic investigations on both mechanical and electrical properties of carbon nano fiber (CNF)-reinforced epoxy matrix nano composites. In this paper, an in-depth study of both static and dynamic mechanical behaviors and electrical properties of CNF/epoxy nano composites with various contents of CNFs is provided. A modified Halpin-Tsai equation is used to evaluate the Young's modulus and storage modulus of the nano composites. The values of Young's modulus predicted using this method account for the effect of the CNF agglomeration and fit well with those obtained experimentally. The results show that the highest tensile strength is found in the epoxy nano composite with a 1.0 wt % CNFs. The alternate-current (AC) electrical properties of the CNF/epoxy nano composites exhibit a typical insulator-conductor transition. The conductivity increases by four orders of magnitude with the addition of 0.1 wt % (0.058 vol %) CNFs and by ten orders of magnitude for nano composites with CNF volume fractions higher than 1.0 wt % (0.578 vol %). The percolation threshold (i.e., the critical CNF volume fraction) is found to be at 0.057 vol %.

Evaluating the effect of crumb rubber and nano silica on the properties of high volume fly ash roller compacted concrete pavement using non-destructive techniques

Directory of Open Access Journals (Sweden)

Bashar S. Mohammed

2018-06-01

Full Text Available The major problems related to roller compacted concrete (RCC pavement are high rigidity, lower tensile strength which causes a tendency of cracking due to thermal or plastic shrinkage, flexural and fatigue loads. Furthermore, RCC pavement does not support the use of dowel bars or reinforcement due to the way it is placed and compacted, these also aided in cracking and consequently increased maintenance cost. To address these issues, high volume fly ash (HVFA RCC pavement was developed by partially replacing 50% cement by volume with fly ash. Crumb rubber was used as a partial replacement to fine aggregate in HVFA RCC pavement at 0%, 10%, 20%, and 30% replacement by volume. Nano silica was added at 0%, 1%, 2% and 3% by weight of cementitious materials to improve early strength development in HVFA RCC pavement and mitigate the loss of strength due to the incorporation of crumb rubber. The nondestructive technique using the rebound hammer test (RHT and ultrasonic pulse velocity (UPV were used to evaluate the effect of crumb rubber and nano silica on the performance of HVFA RCC pavement. The results showed that the use of HVFA as cement replacement decreases both the unit weight, compressive strength, rebound number (RN. Furthermore, the unit weight, compressive strength, RN, UPV and dynamic modulus of elasticity of HVFA RCC pavement all decreases with increase in crumb rubber content and increases with the addition of nano-silica. Combined UPV-RN (SonReb models for predicting the 28 days strength of HVFA RCC pavement based on combining UPV and RN were developed using multivariable regression (double power, bilinear, and double exponential models. The exponential combined SonReb model is the most suitable for predicting the compressive strength of HVFA RCC pavement using UPV and RN as the independent variable with better predicting ability, higher correlation compared to the single variable models. Keywords: Crumb rubber, High volume fly ash, Nano

Effect of Recycled Rubber Particles and Silica on Tensile and Tear Properties of Natural Rubber Composites

Directory of Open Access Journals (Sweden)

Velu CHANDRAN

2016-05-01

Full Text Available Application of scrap rubber and worn out tires in natural rubber compounds has been studied. The scrap rubber can, however, be recycled and compounded with natural rubber and thus can be generated as a rubber composite. In this work, recycled rubber particles (RRP were prepared using pulverization process. Then, RRP was blended with natural rubber and silica compounds, and it was synthesized by two- roll mill and hydraulic press at specified operating conditions. The samples ranging from 0 to 40 phr of RRP loaded with silica were used as constant filler. The mechanical properties and morphological analysis were carried out. The results showed that tensile strength and elongation at break gradually decreased with increasing RRP loading in natural rubber and silica compounds. Tensile modulus went down at 10 phr of RRP and then showed an increasing trend. Hardness increased up to 30 phr of RRP and tear strength increased up to 20 phr of RRP. A comparative study was also carried out with virgin natural rubber vulcanizates. The incorporation of RRP and silica up to 20 phr in natural rubber did not lower the performance of rubber articles. Morphological studies revealed that better filler dispersion, interfacial adhesion, and cross link density could increase the tensile and tear strengths.DOI: http://dx.doi.org/10.5755/j01.ms.22.2.7330

High breakdown-strength composites from liquid silicone rubbers

DEFF Research Database (Denmark)

Vudayagiri, Sindhu; Zakaria, Shamsul Bin; Yu, Liyun

2014-01-01

In this paper we investigate the performance of liquid silicone rubbers (LSRs) as dielectric elastomer transducers. Commonly used silicones in this application include room-temperature vulcanisable (RTV) silicone elastomers and composites thereof. Pure LSRs and their composites with commercially...

Development of novel nano-composite membranes as introduction systems for mass spectrometers: Contrasting nano-composite membranes and conventional inlet systems

Science.gov (United States)

Miranda, Luis Diego

This dissertation presents the development of novel nano-composite membranes as introduction systems for mass spectrometers. These nano-composite membranes incorporate anodic aluminum oxide (AAO) membranes as templates that can be used by themselves or modified by a variety of chemical deposition processes. Two types of nano-composite membranes are presented. The first nano-composite membrane has carbon deposited within the pores of an AAO membrane. The second nano-composite membrane is made by coating an AAO membrane with a thin polymer film. The following chapters describe the transmission properties these nano-composite membranes and compare them to conventional mass spectrometry introduction systems. The nano- composite membranes were finally coupled to the inlet system of an underwater mass spectrometer revealing their utility in field deployments.

High damping properties of magnetic particles doped rubber composites at wide frequency

Energy Technology Data Exchange (ETDEWEB)

Tian, Ye, E-mail: schtiany@163.com [Research Center for Engineering Technology of Polymeric Composites of Shanxi Province, North University of China, Taiyuan 030051 (China); College of Material Science and Engineering, North University of China, Taiyuan 030051 (China); Liu, Yaqing, E-mail: lyq@nuc.edu.cn [Research Center for Engineering Technology of Polymeric Composites of Shanxi Province, North University of China, Taiyuan 030051 (China); College of Material Science and Engineering, North University of China, Taiyuan 030051 (China); He, Minhong; Zhao, Guizhe; Sun, Youyi [Research Center for Engineering Technology of Polymeric Composites of Shanxi Province, North University of China, Taiyuan 030051 (China); College of Material Science and Engineering, North University of China, Taiyuan 030051 (China)

2013-05-15

Highlights: ► A new kind of permanent magnetic rubber was prepared. ► The microstructure and magnetic properties were investigated. ► The mechanical and damping properties were discussed. ► The new material is expected to be an isolator material to a changed frequency. - Abstract: A new kind of rubber composite was prepared by doping SrFe{sub 12}O{sub 19} nanoparticles coated with silane coupling agents (Si-69) into nitrile butadiene rubber (NBR) matrix, which was characterized by the scanning electron microscopy and X-ray spectroscopy. The results showed that the SrFe{sub 12}O{sub 19} nanoparticles were well dispersed in rubber matrix. Furthermore, the mechanical and magnetic properties of the rubber composites were investigated, in which the high tensile strength (15.8 MPa) and high saturation magnetization (22.9 emu/g) were observed. What is more, the high loss factor of the rubber composites was also obtained in a wide frequency range (0–100 Hz) at high loading (80 phr). The result is attributed to that the permanent magnetic field in rubber nanocomposites can absorb shock energy. These results indicate that the new kind of permanent magnetic rubber is expected to be a smart isolator material, in which the isolator will be able to adapt to a changed frequency.

Conductive nano composites based on cellulose nano fiber coated poly aniline via in situ polymerization

International Nuclear Information System (INIS)

Silva, Michael J. da; Sanches, Alex O.; Malmonge, Luiz F.; Malmonge, Jose A.; Medeiros, Eliton S. de; Rosa, Morsyleide F.

2011-01-01

Cellulose nano fiber (CNF) was extracted by acid hydrolysis from cotton microfibril and nano composites of CNF/PANI-DBSA were obtained by in situ polymerization of aniline onto CNF. The ratios between DBSA/aniline and aniline/oxidant were varied and the nano composites were characterized by four probes direct current (dc) electrical conductivity, ultraviolet-visible (UV-Vis-NIR) and FTIR spectroscopy and X-ray diffraction (XRD). Electrical conductive about ∼10 -1 S/cm was research and was independent of DBSA/aniline molar ratio between 2-4 and the aniline/oxidant molar ratio between 1-5. X-ray patterns of the samples show crystalline peaks characteristic of cellulose I. The FTIR spectra confirmed the presence of PANI and CNF in all samples. (author)

Effect of gamma irradiation on sulfur-cured chlorobutyl rubber

International Nuclear Information System (INIS)

Scagliusi, Sandra R.; Cardoso, Elisabeth E.L.; Ono, Lilian S.; Lugao, Ademar B.

2011-01-01

Chlorobutyl rubber (CIIR) is similarly manufactured to butyl rubber (IIR). The insertion of chlorine atom in isoprene group represents an improvement in its properties, such as: high vulcanizing speed, low permanent stress and compatibility with other types of rubber. The presence of reactive chlorine in butyl chlorate allows a variety of vulcanizing techniques, being the cure via sulfur, the most conventional. In these compounds carbon-halogen bonds are weaker than carbon-carbon and carbon-hydrogen bonds, and the main effect of radiation is to break the carbon-halogen bond to give an organic free radical. Irradiations of certain alkyl chlorides can bring about isomerism in which the location of the halogen atom is changed, the carbon skeleton of molecule remaining unaltered. Irradiation of n-butyl chlorides gives high yields of tertiary carbon. The major effect of high energy photon, such as gamma rays, in organic polymers is the generation of free radicals, along changes in mechanical properties. This work aims to the study of irradiation effect on mechanical properties of a sulfur cured chlorobutyl rubber compound, gamma irradiated within 25, 50, 100, 150 e 200 kGy doses range. The techniques used in their characterization were: strength - stress analysis and elasticity modulus. Results obtained were investigated, demonstrated and discussed. (author)

Effect of gamma irradiation on sulfur-cured chlorobutyl rubber

Energy Technology Data Exchange (ETDEWEB)

Scagliusi, Sandra R.; Cardoso, Elisabeth E.L.; Ono, Lilian S.; Lugao, Ademar B., E-mail: srscagliusi@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-07-01

Chlorobutyl rubber (CIIR) is similarly manufactured to butyl rubber (IIR). The insertion of chlorine atom in isoprene group represents an improvement in its properties, such as: high vulcanizing speed, low permanent stress and compatibility with other types of rubber. The presence of reactive chlorine in butyl chlorate allows a variety of vulcanizing techniques, being the cure via sulfur, the most conventional. In these compounds carbon-halogen bonds are weaker than carbon-carbon and carbon-hydrogen bonds, and the main effect of radiation is to break the carbon-halogen bond to give an organic free radical. Irradiations of certain alkyl chlorides can bring about isomerism in which the location of the halogen atom is changed, the carbon skeleton of molecule remaining unaltered. Irradiation of n-butyl chlorides gives high yields of tertiary carbon. The major effect of high energy photon, such as gamma rays, in organic polymers is the generation of free radicals, along changes in mechanical properties. This work aims to the study of irradiation effect on mechanical properties of a sulfur cured chlorobutyl rubber compound, gamma irradiated within 25, 50, 100, 150 e 200 kGy doses range. The techniques used in their characterization were: strength - stress analysis and elasticity modulus. Results obtained were investigated, demonstrated and discussed. (author)

Comparison between properties of polyurethane nano composites prepared by two different methods

International Nuclear Information System (INIS)

Barmar, M.; Barikani, M.; Fereidoonnia, M.

2009-01-01

In this work, a thermoplastic polyurethane elastomer model based on polytetramethylene glycol. toluene diisocyanate and 1,4-butanediol was selected and synthesized. According to this model two types of polyurethane nano composites were prepared by in situ polymerization and melt intercalation procedures. The organo-modified nano clay was used in nano composites samples in 0.4 weight percent level. The prepared nano composites were studied by WAXD, tensile and thermal analysis. Thermal properties of the nano composites were higher than those of pure polyurethane elastomers. Nano composites prepared via melt intercalation method showed a lower tensile strength and hardness than those prepared through in situ polymerization method

Are nano-composites and nano-ionomers suitable for orthodontic bracket bonding?

Science.gov (United States)

Uysal, Tancan; Yagci, Ahmet; Uysal, Banu; Akdogan, Gülsen

2010-02-01

The aim of this study was to test nano-composite (Filtek Supreme Plus Universal) and a newly introduced nano-ionomer (Ketac N100 Light Curing Nano-Ionomer) restorative to determine their shear bond strength (SBS) and failure site locations in comparison with a conventional light-cure orthodontic bonding adhesive (Transbond XT). Sixty freshly extracted human maxillary premolar teeth were arbitrarily divided into three equal groups. The brackets were bonded to the teeth in each group with different composites, according to the manufacturers' instructions. The SBS values of the brackets were recorded in Megapascals (MPa) using a universal testing machine. Adhesive remnant index scores were determined after failure of the brackets. The data were analysed using analysis of variance, Tukey honestly significant difference, and chi-square tests. The results demonstrated that group 1 (Transbond XT, mean: 12.60 +/- 4.48 MPa) had a higher SBS than that of group 2 (nano-composite, mean: 8.33 +/- 5.16 MPa; P nano-ionomer, mean: 6.14 +/- 2.12 MPa; P Nano-composites and nano-ionomers may be suitable for bonding since they fulfil the previously suggested SBS ranges for clinical acceptability, but they are inferior to a conventional orthodontic composite.

Carbon Nano tube Composites for Electronic Packaging Applications: A Review

International Nuclear Information System (INIS)

Aryasomayajula, L.; Wolter, K.J.

2013-01-01

Composite engineering comprises of metal matrix composites. They have high strength-weight ratio, better stiffness, economical production, and ease of availability of raw materials. The discovery of carbon nano tubes has opened new possibilities to face challenges better. Carbon Nano tubes are known for their high mechanical strength, excellent thermal and electrical properties. Recent research has made progress in fabricating carbon nano tube metal matrix and polymer-based composites. The methods of fabrication of these composites, their properties and possible applications restricted to the field of electronic packaging have been discussed in this paper. Experimental and theoretical calculations have shown improved mechanical and physical properties like tensile stress, toughness, and improved electrical and thermal properties. They have also demonstrated the ease of production of the composites and their adaptability as one can tailor their properties as per the requirement. This paper reviews work reported on fabricating and characterizing carbon- nano tube-based metal matrix and polymer composites. The focus of this paper is mainly to review the importance of these composites in the field of electronics packaging.

Metal Matrix Composites Reinforced by Nano-Particles—A Review

Directory of Open Access Journals (Sweden)

Riccardo Casati

2014-03-01

Full Text Available Metal matrix composites reinforced by nano-particles are very promising materials, suitable for a large number of applications. These composites consist of a metal matrix filled with nano-particles featuring physical and mechanical properties very different from those of the matrix. The nano-particles can improve the base material in terms of wear resistance, damping properties and mechanical strength. Different kinds of metals, predominantly Al, Mg and Cu, have been employed for the production of composites reinforced by nano-ceramic particles such as carbides, nitrides, oxides as well as carbon nanotubes. The main issue of concern for the synthesis of these materials consists in the low wettability of the reinforcement phase by the molten metal, which does not allow the synthesis by conventional casting methods. Several alternative routes have been presented in literature for the production of nano-composites. This work is aimed at reviewing the most important manufacturing techniques used for the synthesis of bulk metal matrix nanocomposites. Moreover, the strengthening mechanisms responsible for the improvement of mechanical properties of nano-reinforced metal matrix composites have been reviewed and the main potential applications of this new class of materials are envisaged.

Mathematical Modelling of Optimization of Structures of Monolithic Coverings Based on Liquid Rubbers

Science.gov (United States)

Turgumbayeva, R. Kh; Abdikarimov, M. N.; Mussabekov, R.; Sartayev, D. T.

2018-05-01

The paper considers optimization of monolithic coatings compositions using a computer and MPE methods. The goal of the paper was to construct a mathematical model of the complete factorial experiment taking into account its plan and conditions. Several regression equations were received. Dependence between content components and parameters of rubber, as well as the quantity of a rubber crumb, was considered. An optimal composition for manufacturing the material of monolithic coatings compositions was recommended based on experimental data.

Unraveling the mystery of natural rubber biosynthesis. Part II. Composition and growth of in vitro natural rubber using high-resolution size exclusion chromatography

Energy Technology Data Exchange (ETDEWEB)

Chiang, Cheng Ching K. [Univ. of Akron, OH (United States); Barkakaty, Balaka [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Puskas, Judit E. [Univ. of Akron, OH (United States); Xie, Wenshuang [The Ohio State Univ., Wooster, OH (United States); Cornish, Katrina [The Ohio State Univ., Wooster, OH (United States); Peruch, Federic [Univ. of Bordeaux, Pessac Cedex (France); Deffieux, Alain [Univ. of Bordeaux, Pessac Cedex (France)

2014-09-01

The superior properties of natural rubber (cis-1,4-polyisoprene [NR]) are a function of its structure and composition, properties that still remain a mystery and that are irreplaceable by any synthetic rubber. NR from guayule (Parthenium argentatum) has been gaining special interest for its hypoallergenic properties while maintaining superior mechanical properties that are commonly associated with the Brazilian rubber tree (Hevea brasiliensis), the most common source of NR. Techniques exist to isolate washed rubber particles (WRPs) that contain enzymatically active rubber transferase, to study NR biosynthesis, and previous work on the in vitroNRgrowth in Hevea has demonstrated the presence of around 50wt%of a low molecular weight ([MW], Mn <10 000 g/mol) fraction. Structural and compositional analyses of this low MW fraction in Hevea are challenging due to the high protein content. Here, we discuss the analysis and composition of guayule latex and WRPs using high-resolution Size Exclusion Chromatography. We also discuss the composition of the soluble fraction of inactive guayule latex using matrix-assisted laser desorption ionization/time of flight mass spectrometry.

Polybenzoxazole-filled nitrile butadiene rubber compositions

Science.gov (United States)

Gajiwala, Himansu M. (Inventor); Guillot, David G. (Inventor)

2008-01-01

An insulation composition that comprises at least one nitrile butadiene rubber (NBR) having an acrylonitrile content that ranges from approximately 26% by weight to approximately 35% by weight and polybenzoxazole (PBO) fibers. The NBR may be a copolymer of acrylonitrile and butadiene and may be present in the insulation composition in a range of from approximately 45% by weight to approximately 56% by weight of a total weight of the insulation composition. The PBO fibers may be present in a range of from approximately 3% by weight to approximately 10% by weight of a total weight of the insulation composition. A rocket motor including the insulation composition and a method of insulating a rocket motor are also disclosed.

Preparation and mechanical properties of rubber composites reinforced with carbon nanohorns.

Science.gov (United States)

Isshiki, Tetsuya; Hashimoto, Mikiko; Morii, Masato; Ota, Yuki; Kaneda, Kazuo; Takahashi, Hidetaka; Yudasaka, Masako; Iijima, Sumio; Okino, Fujio

2010-06-01

Nitrile butadiene rubber (NBR) composites with single-wall carbon nanohorns (SWNHs, or simply NHs), hole-opened NHs (h-NHs), and carbon black (CB), the most commonly used nanocarbon rubber filler, were prepared, and their mechanical properties were compared. The NBR composites with h-NHs (NBR/h-NH) showed higher tensile strength than those with NHs (NBR/NH), and the tensile strength of NBR/h-NH or NBR/NH was much greater than those of the NBR composites with CB (NBR/CB). At 5 parts per hundred of rubber (phr), the tensile stresses at break of NBR/h-NH was about 1.8 times larger than those of NBR/CB, and the strain at the break, 1.2 times larger. Similarly, at 20 phr, both the tensile strength and strain at the break of NBR/h-NH were 1.4 times larger than those of NBR/CB. NBR/NH showed the highest hardness while having the smallest specific gravity. The present results indicate that NHs and h-NHs have much superior reinforcement effects to CB for NBR rubber matrix.

Chemical Functionalization, Self-Assembly, and Applications of Nano materials and Nano composites 2014

International Nuclear Information System (INIS)

Yan, X.; Jiao, T.; Balan, L.; Chen, X.; Hu, M.Z.; Liu, W.

2014-01-01

The growing interests in nano materials and nano composites call for the development of processing techniques to obtain multiple functionalization nano structures and achieve the tailoring of specific features of the nanometer size. Functional nano materials and nano composites will expand the applied range of the original material and at the same time promote the development of inter discipline. Thus, the chemical functionalization and bottom-up assemblies of nano materials and subsequent applications will accelerate the development of nano science and nano technology.

Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

International Nuclear Information System (INIS)

Dessouki, A.M.; Taher, N.H.; El-Nahas, H.H.

1996-01-01

The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the ζ potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs

Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

Dessouki, A M; Taher, N H; El-Nahas, H H [National Center for Radiation Research and Technology, Atomic Energy Athority, Cairo (Egypt)

1996-03-01

The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the {zeta} potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs.

PROPERTIES TYRE TREAD RUBBERS DEPENDING ON PARTICULARITY OF RUBBER COMPOUND

Directory of Open Access Journals (Sweden)

Z. S. Shashok

2014-01-01

Full Text Available Summary. The results of studies of the elastomeric compositions based on natural rubber containing curatives different ratio "curing agent : vulcanization accelerator" listed in this article. Influence of the composition of the vulcanizing group on stress-strain and elastic- deformation properties of tire tread rubber was installed. It has been shown that a significant effect on thermo-oxidative aging of vulcanizates was the composition of the vulcanizing group. Results of studies resistance tread rubber to exposure to elevated temperatures were presented . Vulcanizates differing type and density by varying the cross-linking ratio of "curing agent : vulcanization accelerator" were obtained . Research results in the formation of rubber resistance and crack growth at different temperatures were presented. Revealed that the best education and resistance to tear propagation under normal conditions characterized by rubber ratio "curing agent : vulcanization accelerator" equal to 1.5:1. It has been established that a dynamic endurance study rubbers depends largely on the nature and concentration of the cross-linking cross-links and movable promote increase efficiency due to the grid and reduce the sulfidity rearrangement. During loading mode alternating deformations at elevated temperatures lability of polysulfide bonds negatively affects the performance of rubber, and the decisive role of providing strength and thermal cross-linking. It is shown that the performance of the spatial grid rubbers allow indirectly judge the dynamic vulcanizates endurance and predict performance rubbers at elevated temperatures under conditions of repeated cyclic deformation. Revealed that the vulcanizing system containing sulfur and vulcanization accelerator TBBS 1:2, promotes the formation of the optimal structure of vulcanized rubber , which provides the best resistance to repeated cyclic deformations in the operating temperatures of the tire.

Investigation on polyethylene-supported and nano-SiO2 doped poly(methyl methacrylate-co-butyl acrylate) based gel polymer electrolyte for high voltage lithium ion battery

International Nuclear Information System (INIS)

Xie, Huili; Liao, Youhao; Sun, Ping; Chen, Tingting; Rao, Mumin; Li, Weishan

2014-01-01

Highlights: • P(MMA-co-BA)/nano-SiO 2 /PE based GPE was developed for high voltage lithium ion battery. • P(MMA-co-BA)/nano-SiO 2 /PE has uniform and interconnected pore structure. • The GPE exhibits improved ionic conductivity and compatibility with electrodes. • 5 V battery using the GPE presents excellent cyclic stability. - Abstract: Nano-SiO 2 as dopant was used for preparing polyethylene-supported poly(methyl methacrylate-co-butyl acrylate) (P(MMA-co-BA)/PE) based membrane and corresponding gel polymer electrolyte (GPE), which is applied to improve the cyclic stability of high voltage lithium ion battery. P(MMA-co-BA)/nano-SiO 2 /PE based membranes and corresponding GPEs were characterized with scanning electron spectroscopy, X-ray diffraction, electrochemical impedance spectroscopy, mechanical test, thermogravimetric analysis, linear sweep voltammetry, and charge/discharge test. It is found that the GPE with 5 wt.% nano-SiO 2 shows the best performance. Compared to the undoped membrane, the 5 wt.% nano-SiO 2 doped membrane has a better pore structure and higher electrolyte uptake, leading to the enhancement in ionic conductivity of the resulting GPE from 1.23 × 10 −3 to 2.26 × 10 −3 S.cm −1 at room temperature. Furthermore, the thermal stability of the doped membrane is increased from 300 to 320 °C while its decomposition potential of GPE is from 5.0 to 5.6 V (vs. Li/Li + ). The cyclic stability of Li/GPE/Li(Li 0.13 Ni 0.30 Mn 0.57 )O 2 cell at the high voltage range of 3.5 V ∼ 5.0 V is consequently improved, the capacity retention of the cell using the doped membrane is 92.8% after 50 cycles while only 88.9% for the cell using undoped membrane and 66.9% for the cell using liquid electrolyte

Improving Mechanical Properties of Molded Silicone Rubber for Soft Robotics Through Fabric Compositing.

Science.gov (United States)

Wang, Yue; Gregory, Cherry; Minor, Mark A

2018-06-01

Molded silicone rubbers are common in manufacturing of soft robotic parts, but they are often prone to tears, punctures, and tensile failures when strained. In this article, we present a fabric compositing method for improving the mechanical properties of soft robotic parts by creating a fabric/rubber composite that increases the strength and durability of the molded rubber. Comprehensive ASTM material tests evaluating the strength, tear resistance, and puncture resistance are conducted on multiple composites embedded with different fabrics, including polyester, nylon, silk, cotton, rayon, and several blended fabrics. Results show that strong fabrics increase the strength and durability of the composite, valuable in pneumatic soft robotic applications, while elastic fabrics maintain elasticity and enhance tear strength, suitable for robotic skins or soft strain sensors. Two case studies then validate the proposed benefits of the fabric compositing for soft robotic pressure vessel applications and soft strain sensor applications. Evaluations of the fabric/rubber composite samples and devices indicate that such methods are effective for improving mechanical properties of soft robotic parts, resulting in parts that can have customized stiffness, strength, and vastly improved durability.

A new mechanism for selective adsorption of rubber on carbon black surface caused by nano-confinement in SBR/NBR solution

Science.gov (United States)

Kawazoe, Masayuki

A novel mechanism of selective adsorption of rubber molecules onto carbon black surface in a binary immiscible rubber blend solution has been proposed in this dissertation. The phenomenon leads to uneven distribution of carbon black to the specific polymer in the blend and the obtained electrically conductive composite showed drastic reduction of percolation threshold concentration (PTC). The mechanism and the feature of conductive network formation have much potential concerning both fundamental understanding and industrial application to improve conductive polymer composites. In chapter I, carbon black filled conductive polymer composites are briefly reviewed. Then, in chapter II, a mechanism of rubber molecular confinement into carbon black aggregate structure is introduced to explain the selective adsorption of a specific rubber onto carbon black surface in an immiscible rubber solution blend (styrene butadiene rubber (SBR) and acrylonitrile butadiene rubber (NBR) with toluene or chloroform). Next, in chapters III and IV, polymers with various radius of gyration (Rg) and carbon blacks with various aggregate structure are examined to verify the selective adsorption mechanism. Finally, in chapter V, the novel mechanism was applied to create unique meso-/micro-unit conductive network in carbon black dispersed SBR/NBR composites.

Studies on the effect of nano-TiO{sub 2} on vinyl acetate-butyl acrylate latex-based surface coating

Energy Technology Data Exchange (ETDEWEB)

Suma, K.K. [Dept. of Polymer Science and Rubber Technology, Cochin University of Science and Technology, Kochi 22, Kerala (India); Dept. of Chemistry, Maharaja' s College, Ernakulam, Kerala (India); Jacob, Sinto [Dept. of Polymer Science and Rubber Technology, Cochin University of Science and Technology, Kochi 22, Kerala (India); Joseph, Rani, E-mail: rani@cusat.ac.i [Dept. of Polymer Science and Rubber Technology, Cochin University of Science and Technology, Kochi 22, Kerala (India)

2010-04-15

Vinyl acetate-butyl acrylate (VAc-BuA) copolymer latex was prepared by emulsion polymerization. The polymerization conditions and the composition were optimized. The 85/15 wt.% (vinyl acetate/butyl acrylate) gave good tensile strength of the order of 15.6 MPa and a glass transition temperature (T{sub g}) value of -6.49 deg. C. This copolymer was used as a binder in the paint formulation. In this formulation nanosized TiO{sub 2} sol was used as a pigment instead of conventional rutile TiO{sub 2}. Nanosized TiO{sub 2} is prepared by wet process. These nanosized TiO{sub 2} rutile colloidal sol has improved properties such as photostability, UV shielding, dispersion stability, etc. The surface properties of paint were found to be superior compared to commercially used paint.

High performance nano-composite technology development

International Nuclear Information System (INIS)

Kim, Whung Whoe; Rhee, C. K.; Kim, S. J.; Park, S. D.; Kim, E. K.; Jung, S. Y.; Ryu, H. J.; Hwang, S. S.; Kim, J. K.; Hong, S. M.; Chea, Y. B.; Choi, C. H.; Kim, S. D.; Cho, B. G.; Lee, S. H.

1999-06-01

The trend of new material development are being to carried out not only high performance but also environmental attraction. Especially nano composite material which enhances the functional properties of components, extending the component life resulting to reduced the wastes and environmental contamination, has a great effect on various industrial area. The application of nano composite, depends on the polymer matrix and filler materials, has various application from semiconductor to medical field. In spite of nano composite merits, nano composite study are confined to a few special materials as a lab, scale because a few technical difficulties are still on hold. Therefore, the purpose of this study establishes the systematical planning to carried out the next generation projects on order to compete with other countries and overcome the protective policy of advanced countries with grasping over sea's development trends and our present status. (author).

High performance nano-composite technology development

Energy Technology Data Exchange (ETDEWEB)

Kim, Whung Whoe; Rhee, C. K.; Kim, S. J.; Park, S. D. [KAERI, Taejon (Korea, Republic of); Kim, E. K.; Jung, S. Y.; Ryu, H. J. [KRICT, Taejon (Korea, Republic of); Hwang, S. S.; Kim, J. K.; Hong, S. M. [KIST, Taejon (Korea, Republic of); Chea, Y. B. [KIGAM, Taejon (Korea, Republic of); Choi, C. H.; Kim, S. D. [ATS, Taejon (Korea, Republic of); Cho, B. G.; Lee, S. H. [HGREC, Taejon (Korea, Republic of)

1999-06-15

The trend of new material development are being to carried out not only high performance but also environmental attraction. Especially nano composite material which enhances the functional properties of components, extending the component life resulting to reduced the wastes and environmental contamination, has a great effect on various industrial area. The application of nano composite, depends on the polymer matrix and filler materials, has various application from semiconductor to medical field. In spite of nano composite merits, nano composite study are confined to a few special materials as a lab, scale because a few technical difficulties are still on hold. Therefore, the purpose of this study establishes the systematical planning to carried out the next generation projects on order to compete with other countries and overcome the protective policy of advanced countries with grasping over sea's development trends and our present status. (author).

Influence of Rubber Powders on Foaming Behavior and Mechanical Properties of Foamed Polypropylene Composites

Directory of Open Access Journals (Sweden)

HE Yue

2017-02-01

Full Text Available Polypropylene/rubber powders composites with different kinds of rubber powders were foamed by injection molding machine equipped with volume-adjustable cavity. The effect of dispersity of rubber powders and crystallization behavior of composites on the foaming behavior and mechanical properties was investigated. The results show that the addition of rubber powders can improve the cell structure of foamed PP with fine and uniform cell distribution. And cell density and size of PP/PP-MAH/NBR foams are 7.64×106cell/cm3 and 29.78μm respectively, which are the best among these foams. Combining cell structures with mechanical properties, notch impact strength of PP/PP-MAH/CNBR composites increases approximately by 2.2 times while tensile strength is reduced just by 26% compared with those of the pure PP. This indicates that PP/PP-MAH/CNBR composites are ideal foamed materials.

TLC/IR (UATR off-line coupling for the characterization of additives in EPDM rubber compositions

Directory of Open Access Journals (Sweden)

Denis Damazio

2016-02-01

Full Text Available Abstract The knowledge of the components that constitutes a rubber composition is important to justify the properties of the final device, particularly when it comes to elastomeric compositions used in the aerospace industry. The development of methodologies that can detect components, specially the smallest proportion of the rubbers composition is a constant challenge and an important gap in the studies of this nature. Therefore, methodologies by using standard techniques and/or of last generation are important in rubber industry and research laboratories, aiming application in related research. In this context, this study shows the coupling/association techniques (off-line of thin layer chromatography and infrared spectroscopy (TLC/IR, being the IR spectra obtained by universal attenuated total reflection (UATR, applied to the analysis of additives in rubber compositions of ethylene-propylene-diene rubber (EPDM. Two EPDM compositions, a kind of eluent system and Gibbs' reagent, as developer, were used. Basically, all organic components were detected by this methodology, being possible to suggest that it can be applied for detecting additives of similar chemical structures, even though it's presents in small amounts in the composition.

Nano-reinforcement of tire rubbers: silica-technology for natural rubber : exploring the infuence of non-rubber constituents on the natural rubber-silica system

NARCIS (Netherlands)

Sarkawi, S.S.

2013-01-01

Natural rubber is a renewable resource material with outstanding properties which offers significant advantages over its counterparts, the fossil-resource synthetic rubbers. In fact, a natural rubber tree is an efficient carbon dioxide sequester. Since natural rubber is a natural product, it is

The use of plasticizing additives based on recycled raw materials in the petrochemical rubber mixtures

Directory of Open Access Journals (Sweden)

Z. S. Shashok

2016-01-01

Full Text Available At present, the development of alternative products for elastomers based on recycling petrochemical raw materials is a new trend of the rubber industry progress. Petrochemical raw materials include spent lubricants and motor oils are among such recycling products. In this context, the influence of the products of recycling waste engine oil (DVCH and RA in comparison with industrial oil (I-20 on the technological properties of filled elastomeric compositions was investigated. The elastomeric compositions were based on poly isoprene and divinyl rubbers. The plasticizing components were manufactured by IOOO “DVCH-Menedzhment”. They are mixture of hydro-carbons, C16–C20 and differ from each other in the content of linear and branched paraffin. Plastic-elastic properties of rubber compounds on the shear disk viscometer MV2000 in accordance with GOST 10722–76 was carried out. Kinetics of vulcanization on the rheometer ODR2000 according to GOST 12535–84 was defined. It is shown that the introduction of RA test plasticizing component provides a significant effect on Mooney viscosity, as compared to elastomeric compositions containing a plasticizer and I-20 and plasticizing additive DVCH. It revealed that the administration of all components in the studied plasticizing elastomer compositions based on a combination poly isoprene and divinyl rubbers has no significant effect on the rate of relaxation of stress of rubber compounds. It is found that elastomeric compositions containing as additives investigated processing waste oil products (DVCH and RA are characterized by a slightly smaller value of time to reach an optimal degree of vulcanization.

Effect of antimicrobial agents on cellulose acetate nano composites properties

Energy Technology Data Exchange (ETDEWEB)

Rodriguez, Francisco J.; Bruna, Julio E.; Galotto, Maria J.; Guarda, Abel; Sepulveda, Hugo, E-mail: francisco.rodriguez.m@usach.cl [Center for the Development of Nanoscience and Nanotechnology (CEDENNA). Universidad de Santiago de Chile. Faculty of Technology. Department of Food Science and Technology. Food Packaging Laboratory. Santiago (Chile)

2011-07-01

Nano composites based on cellulose acetate, Cloisite 30B, triethyl citrate and thymol or cinnamaldehyde were prepared using a dissolution casting technique. The effect of thymol and cinnamaldehyde on the cellulose acetate nano composite properties was evaluated by XRD and DSC. Important changes on the thermal properties and morphological structure were observed according to thymol and cinnamaldehyde content. (author)

Effect of antimicrobial agents on cellulose acetate nano composites properties

International Nuclear Information System (INIS)

Rodriguez, Francisco J.; Bruna, Julio E.; Galotto, Maria J.; Guarda, Abel; Sepulveda, Hugo

2011-01-01

Nano composites based on cellulose acetate, Cloisite 30B, triethyl citrate and thymol or cinnamaldehyde were prepared using a dissolution casting technique. The effect of thymol and cinnamaldehyde on the cellulose acetate nano composite properties was evaluated by XRD and DSC. Important changes on the thermal properties and morphological structure were observed according to thymol and cinnamaldehyde content. (author)

High performance nano-composite technology development

Energy Technology Data Exchange (ETDEWEB)

Kim, Whung Whoe; Rhee, C. K.; Kim, S. J.; Park, S. D. [KAERI, Taejon (Korea, Republic of); Kim, E. K.; Jung, S. Y.; Ryu, H. J. [KRICT, Taejon (Korea, Republic of); Hwang, S. S.; Kim, J. K.; Hong, S. M. [KIST, Taejon (Korea, Republic of); Chea, Y. B. [KIGAM, Taejon (Korea, Republic of); Choi, C. H.; Kim, S. D. [ATS, Taejon (Korea, Republic of); Cho, B. G.; Lee, S. H. [HGREC, Taejon (Korea, Republic of)

1999-06-15

The trend of new material development are being to carried out not only high performance but also environmental attraction. Especially nano composite material which enhances the functional properties of components, extending the component life resulting to reduced the wastes and environmental contamination, has a great effect on various industrial area. The application of nano composite, depends on the polymer matrix and filler materials, has various application from semiconductor to medical field. In spite of nano composite merits, nano composite study are confined to a few special materials as a lab, scale because a few technical difficulties are still on hold. Therefore, the purpose of this study establishes the systematical planning to carried out the next generation projects on order to compete with other countries and overcome the protective policy of advanced countries with grasping over sea's development trends and our present status. (author).

Nano-Fiber Reinforced Enhancements in Composite Polymer Matrices

Science.gov (United States)

Chamis, Christos C.

2009-01-01

Nano-fibers are used to reinforce polymer matrices to enhance the matrix dependent properties that are subsequently used in conventional structural composites. A quasi isotropic configuration is used in arranging like nano-fibers through the thickness to ascertain equiaxial enhanced matrix behavior. The nano-fiber volume ratios are used to obtain the enhanced matrix strength properties for 0.01,0.03, and 0.05 nano-fiber volume rates. These enhanced nano-fiber matrices are used with conventional fiber volume ratios of 0.3 and 0.5 to obtain the composite properties. Results show that nano-fiber enhanced matrices of higher than 0.3 nano-fiber volume ratio are degrading the composite properties.

Effects of radio sensitizers in the vulcanization of natural rubber latex induced by gamma radiation

International Nuclear Information System (INIS)

Souza, A. de; Canavel, V.; Araujo, S.C. de; Guedes, S.M.L.

1992-01-01

The effect of C Cl 4 and n-butyl acrylate as a sensitizer for radiation vulcanization of 60% DRC natural rubber latex with gamma rays, was studied relating tensile strength of vulcanized latex. The vulcanization dose is 200 kGy for natural rubber latex and it decreases to 40 kGy and to 9 kGy in the presence of C Cl 4 / potassium laureate and n-butyl acrylate / t-butyl hydroperoxide, respectively. The H 2 O 2 as a co-sensitizer does not change the efficiency of the combination of these sensitizers. The IV spectra show the formation of C=O after the irradiation as consequence of oxidation reactions. (author)

A novel use of bio-based natural fibers, polymers, and rubbers for composite materials

Science.gov (United States)

Modi, Sunny Jitendra

The composites, materials, and packaging industries are searching for alternative materials to attain environmental sustainability. Bio-plastics are highly desired and current microbially-derived bio-plastics, such as PHA (poly-(hydroxy alkanoate)), PHB (poly-(hydroxybutyrate)), and PHBV (poly-(beta-hydroxy butyrate-co-valerate)) could be engineered to have similar properties to conventional thermoplastics. Poly-(hydroxybutyrate) (PHB) is a bio-degradable aliphatic polyester that is produced by a wide range of microorganisms. Basic PHB has relatively high glass transition and melting temperatures. To improve flexibility for potential packaging applications, PHB is synthesized with various co-polymers such as Poly-(3-hydroxyvalerate) (HV) to decrease the glass and melting temperatures and, since there is improved melt stability at lower processing temperatures, broaden the processing window. However, previous work has shown that this polymer is too brittle, temperature-sensitive, and hydrophilic to meet packaging material physical requirements. Therefore, the proposed work focuses on addressing the needs for bio-derived and bio-degradable materials by creating a range of composite materials using natural fibers as reinforcement agents in bio-polymers and bio- plastic-rubber matrices. The new materials should possess properties lacking in PHBV and broaden the processing capabilities, elasticity, and improve the mechanical properties. The first approach was to create novel composites using poly-(beta-hydroxy butyrate-co-valerate) (PHBV) combined with fibers from invasive plants such as common reed (Phragmites australis), reed canary grass (Phalaris arundinacea), and water celery ( Vallisneria americana). The composites were manufactured using traditional processing techniques of extrusion compounding followed by injection molding of ASTM type I parts. The effects of each bio-fiber at 2, 5, and 10% loading on the mechanical, morphological, rheological, and thermal

Interfacial interaction between the epoxidized natural rubber and silica in natural rubber/silica composites

Science.gov (United States)

Xu, Tiwen; Jia, Zhixin; Luo, Yuanfang; Jia, Demin; Peng, Zheng

2015-02-01

The epoxidized natural rubber (ENR) as an interfacial modifier was used to improve the mechanical and dynamical mechanical properties of NR/silica composites. In order to reveal the interaction mechanism between ENR and silica, the ENR/Silica model compound was prepared by using an open mill and the interfacial interaction of ENR with silica was investigated by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), X-ray diffraction (XRD) and stress-strain testing. The results indicated that the ring-opening reaction occurs between the epoxy groups of ENR chains and Si-OH groups on the silica surfaces and the covalent bonds are formed between two phases, which can improve the dispersion of silica in the rubber matrix and enhance the interfacial combination between rubber and silica. The ring-opening reaction occurs not only in vulcanization process but also in mixing process, meanwhile, the latter seems to be more important due to the simultaneous effects of mechanical force and temperature.

Nuclear magnetic resonance applied to the study of polymeric nano composites

International Nuclear Information System (INIS)

Tavares, Maria Ines Bruno

2011-01-01

Polymers and nanoparticles based nano composites were prepared by intercalation by solution. The obtained nano composites were characterized mainly by the nuclear magnetic spectroscopy (NMR), applying the analysis of carbon-13 (polymeric matrix), silicon-29 (nanoparticle), and by determination of spin-lattice relaxation of the hydrogen nucleus (T 1 H) (polymeric matrix). The NMR have presented a promising technique in the characterization of the nano charge dispersion in the studied polymeric matrixes.

Improved natural rubber composites reinforced with a complex filler network of biobased nanoparticles and ionomer

Science.gov (United States)

Biobased rubber composites are renewable and sustainable. Significant improvement in modulus of rubber composite reinforced with hydrophilic filler was achieved with the inclusion of ionomers. Soy particles aided with ionomer, carboxylated styrene-butadiene (CSB), formed a strong complex filler netw...

Functional properties of extruded nano composites based on cassava starch, polyvinyl alcohol and montmorillonite

International Nuclear Information System (INIS)

Debiagi, Flavia; Matsuda, Daniel K.M.; Marengo, Vitor A.; Vercelheze, Ana Elisa S.; Mali, Suzana

2011-01-01

The objectives of this work were to produce biodegradable trays based on cassava starch (native or modified by acid), sugarcane fibers and nano clay (sodium montmorillonite) and also to characterize the produced trays according to their density, tensile strength, X-ray diffraction and biodegradability. The trays were obtained by thermoforming into a hydraulic press coupled to a Teflon mold (18 x 23 cm) at 130 degree C/ 20 min and 100 bars of pressure. The peak related to the nano clay (2 = 7.1 o ) were not observed in XRD patterns of the trays, suggesting the formation of an exfoliated structure in the nano composite. The addition of modified starch increased tensile strength and density of the samples, and the addition of fibers and nano clays decreased the tensile strength of native and modified starch trays. The weight loss of trays was not affected by the starch type, however the addition of fibers increased the biodegradation and the addition of nano clays decreased. (author)

Thermal and mechanical properties of palm oil-based polyurethane acrylate/ clay nano composites prepared by in-situ intercalative method and electron beam radiation

International Nuclear Information System (INIS)

Salih, A.M.; Mansor Ahmad; Nor Azowa Ibrahim; Rida Tajau; Wan Mohd Zin Wan Yunus

2013-01-01

Full-text: Palm oil based-polyurethane acrylate (POBUA)/ clay nano composites were prepared via in-situ intercalative polymerization using epoxidized palm oil acrylate (EPOLA) and 4,4 ' methylene diphenyl diisocyante (MDI). Organically modified Montmorillonite (ODA-MMT) was incorporated in EPOLA (1, 3 and 5 % wt), and then subjected to polycondensation reaction with MDI. Nano composites solid films were obtained successfully by electron beam radiation induced free radical polymerization (curing). FTIR results reveal that the prepolymer was obtained successfully, with nano clay dispersed in the matrix. The intercalation of the clay in the polymer matrix was investigated by XRD and the interlayer spacing of clay was found to be increased up to 37 Angstrom, while the structure morphology of the nano composites was investigated by TEM and SEM. The nano composites were found to be a mixture of exfoliated and intercalated morphologies. The thermal stability of the nano composites was significantly increased by incorporation of nano clay into the polymer matrix. DSC results reveal that the T g was shifted to higher values, gradually with increasing the amount of filler in the nano composites. Tensile strength and Young's modulus of the nano composites showed remarkable improvement compared to the neat POBUA. (author)

The effect of organo-clay on the dielectric properties of silicone rubber

International Nuclear Information System (INIS)

Razzaghi-Kashani, M; Gharavi, N; Javadi, S

2008-01-01

Dielectric elastomers are highly deformable and fast response smart materials capable of actuation under electric fields. Among commercially available dielectric elastomers, silicone rubber can be compounded with different fillers in order to modify its electrical and mechanical properties. To study the effect of organically modified montmorillonite (OMMT) on the dielectric properties of silicone rubber, OMMT was added to this rubber at two levels, 2% and 5%, using two methods, low-shear and high-shear mixing. Composites were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The XRD patterns showed different crystallite structures for silicate platelets in the rubber matrix as a result of the two different mixing methods. In low-shear mixing, the ordered crystallite structure of the clay remains almost unchanged, whereas in high-shear mixing it loses its ordered structure, leading to the disappearance of the diffraction peaks. SEM and AFM micrographs depicted better dispersion and more uniform distribution of the organo-clay under high-shear mixing compared to those obtained by low-shear mixing. The tensile properties also confirmed the different degree of dispersion of the nano-clay resulting from the two different methods of mixing. The dielectric properties of the composites were measured under AC electric fields, and the results were compared with reference silicone rubbers with no OMMT. It was shown that the order of organo-clay layers in the less dispersed structure of the clay imparts an additional ionic polarization and higher dielectric permittivity compared to the case where the clay layers are more dispersed and lost their order. The storage and loss dielectric constants of base silicone rubber increase when it is compounded with OMMT

Preparation of polymer-organo clay nano composites through the spray drying process

International Nuclear Information System (INIS)

Bernardo, Paulo R.A.; Pessan, Luiz A.; Carvalho, Antonio J.F. de; Vidotti, Suel E.

2011-01-01

The objective of the work was the study and preparation of polymer nano composites with montmorillonite organo clays (MMT) through the spray drying process. A new technique was proposed and tested to obtaining polymer nano composites, based on the use of the spray drying process to produce a nano composite with high clay content. The process consisted of the following stages: clay intercalation in water solution, with after addition of polyvinyl alcohol (PVOH) and a hydro soluble polyester ionomer (GEROLPS20) as exfoliation agents; spray drying the mixture obtained; incorporation powder in EVOH, PET e PP matrix. The effects of exfoliation agent on morphological and thermal properties of the nano composites were studied by XRD, transmission electron microscopy (TEM) and TGA. The results demonstrate that the process of spray drying is an innovative way to obtain a nano composite with high clay content. (author)

The Degradation of Mechanical Properties in Halloysite Nano clay-Polyester Nano composites Exposed in Seawater Environment

International Nuclear Information System (INIS)

Saharudin, M.S.; Saharudin, M. Sh.; Wei, J.; Shyha, I.; Inam, F.

2016-01-01

Polyester based polymers are extensively used in aggressive marine environments; however, inadequate data is available on the effects of the seawater on the polyester based nano composites mechanical properties. This paper reports the effect of seawater absorption on the mechanical properties degradation of halloysite nano clay-polyester nano composites. Results confirmed that the addition of halloysite nano clay into polyester matrix was found to increase seawater uptake and reduce mechanical properties compared to monolithic polyester. The maximum decreases in microhardness, tensile and flexural properties, and impact toughness were observed in case of 1 wt% nano clay. The microhardness decreased from 107 HV to 41.7 HV (61% decrease). Young s modulus decreased from 0.6 GPa to 0.4 GPa (33% decrease). The flexural modulus decreased from 0.6 GPa to 0.34 GPa (43% decrease). The impact toughness dropped from 0.71 kJ/m"2 to 0.48 kJ/m"2 (32% decrease). Interestingly, the fracture toughnessκ_1C increased with the addition of halloysite nano clay due to the plasticization effect of the resin matrix. SEM images revealed the significant reduction in mechanical properties in case of 1 wt% reinforcement which is attributed to the degradation of the nano clay-matrix interface influenced by seawater absorption and agglomeration of halloysite nano clay.

A comparative investigation on strain induced crystallization for graphene and carbon nanotubes filled natural rubber composites

Directory of Open Access Journals (Sweden)

D. H. Fu

2015-07-01

Full Text Available Natural rubber containing graphene and carbon nanotubes (CNTs composites were prepared by ultrasonicallyassisted latex mixing. Natural rubber filled by both graphene and CNTs show significant enhanced tensile strength, while graphene exhibits a better reinforcing effect than CNTs. Strain-induced crystallization in natural rubber composites during stretching was determined by synchrotron wide-angle X-ray diffraction. With the addition of CNTs or graphene, the crystallization for natural rubber occurs at a lower strain compared to unfilled natural rubber, and the strain amplification effects were observed. The incorporation of graphene results in a faster strain-induced crystallization rate and a higher crystallinity compared to CNTs. The entanglement-bound rubber tube model was used to analyze the chain network structure and determine the network parameters of composites. The results show that the addition of graphene or CNTs has an influence on the molecular network structure and improves the contribution of entanglement to the conformational constraint, while graphene has a more marked effect than CNTs.

Fabrication and mechanical evaluation of hydroxyapatite/oxide nano-composite materials

Energy Technology Data Exchange (ETDEWEB)

Mohamed, Khaled R., E-mail: Kh_rezk1966@yahoo.com [Biomaterials Dept., National Research Centre, El-Behoos St., Cairo (Egypt); Beherei, Hanan H. [Biomaterials Dept., National Research Centre, El-Behoos St., Cairo (Egypt); Physics Dept., Faculty of Science, El-Taif University (Saudi Arabia); El Bassyouni, Gehan T. [Biomaterials Dept., National Research Centre, El-Behoos St., Cairo (Egypt); Medical Physics Dept., Faculty of Medicine, El-Taif University (Saudi Arabia); El Mahallawy, Nahed [Design and Production Engineering Department, Faculty of Engineering, Ain Shams University on secondment to the German University in Cairo (Egypt)

2013-10-15

In the current study, the semiconducting metal oxides such as nano-ZnO and SiO{sub 2} powders were prepared via sol–gel technique and conducted on nano-hydroxyapatite (nHA) which was synthesized by chemical precipitation. The properties of fabricated nano-structured composites containing different ratios of HA, ZnO and SiO{sub 2} were examined using X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscope (SEM) and transmission electron microscope (TEM) techniques. The effect of the variation of ratios between the three components on mechanical, microstructure and in-vitro properties was assessed to explore the possibility of enhancing these properties. The results proved that the mechanical properties exhibited an increment with increasing the ZnO content at the extent of HA. In-vitro study proved the formation and nucleation of apatite onto the surface of the fabricated composites after one week of immersion. It is concluded that HA composites containing SiO{sub 2} or SiO{sub 2}/ZnO content had a suitable mechanical properties and ability to form apatite particles onto the composite surface. Based on bioactivity behavior, Si-HA is more bioactive than pure hydroxyapatite and nano-arrangements will provide an interface for better bone formation. Therefore, these nano-composites will be promising as bone substitutes especially in load bearing sites. - Graphical abstract: Nano-structures of (a) HA, (b) ZnO and (c) SiO{sub 2} powders. Highlights: • The nano-structured composites containing different ratios of HA, ZnO and SiO{sub 2} were prepared. • ZnO helps improve the mechanical properties of HA composites. • SiO{sub 2} helps improve the bioactivity of HA composites.

UV resistibility of a nano-ZnO/glass fibre reinforced epoxy composite

International Nuclear Information System (INIS)

Wong, Tsz-ting; Lau, Kin-tak; Tam, Wai-yin; Leng, Jinsong; Etches, Julie A.

2014-01-01

Highlights: • A GFRE composite with UV resistibility is introduced. • The bonding behaviour and UV resistibility of the composite were studied upon the addition of nano-ZnO particles. • The solvent effect in the dispersion of nano-ZnO particles was also studied. • The nano-ZnO/GFRE composite shows effective UV absorption with enhanced bonding behaviour. - Abstract: The harmfulness of ultraviolet (UV) radiation (UVR) to human health and polymer degradation has been the focus recently in all engineering industries. A polymer-based composite filled with nano-ZnO particles can enhance its UV resistibility. It has been found that the use of appropriate amount of nano-ZnO/Isopropyl alcohol solvent to prepare a UV resistant nano-ZnO/glass fibre reinforced epoxy (ZGFRE) composite can effectively block the UV transmission with negligible influence on the crystal structure of its resin system. This paper aims at investigating the interfacial bonding behaviour and UV resistibility of a ZGFRE composite. The solvent effect in relation to the dispersion properties of ZnO in the composite is also discussed. XRD results indicated that 20 wt% Isopropyl alcohol was an effective solvent for filling nano-ZnO particles into an epoxy. SEM examination also showed that the bonding behaviour between glass fibre and matrix was enhanced after filling 20 wt% nano-ZnO particles with 20 wt% Isopropyl alcohol into the composite. Samples filled with 20 wt% nano-ZnO/Isopropyl alcohol and 40 wt% nano-ZnO/Isopropyl alcohol has full absorption of UVA (315–400 nm), UVB (280–315 nm) and a part of UVC (190–280 nm)

Characterization and bioactivity of nano-submicro octacalcium phosphate/gelatin composite

International Nuclear Information System (INIS)

Miura, Kei-ichiro; Anada, Takahisa; Honda, Yoshitomo; Shiwaku, Yukari; Kawai, Tadashi; Echigo, Seishi; Takahashi, Tetsu; Suzuki, Osamu

2013-01-01

The present study was designed to investigate the physicochemical and bioactive properties of a nano-submicro sized octacalcium phosphate (OCP)-dispersed gelatin (Gel) composite (nano-submicro OCP/Gel) used as a bone substitute material in various bone defects. Well-grown, synthesized OCP was mechanically ground from 100 to 300 μm-sieved granules to particles that were approximately 500 nm in size. Then, 50 wt% of the nano-submicro OCP was mixed with porcine skin-derived acid extracted gelatin. The mixture was molded and lyophilized and then subjected to dehydrothermal crosslinking. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy showed that the structure of OCP was retained even after mechanical grinding to a nano-submicro scale level as well as inclusion in the Gel matrix. The bioactivity of nano-submicro OCP/Gel was examined by immersing the composite in simulated body fluid (SBF) for 7 days and by implanting it in rat critical-sized calvaria defects for 8 weeks. The nano-submicro OCP tended to convert to low crystalline hydroxyapatite (HA) in SBF as assessed by XRD. The nano-submicro OCP/Gel exhibited osteoconductivity in vivo, yielding new bone formation that was closely associated with the implanted composite. These results suggest that the nano-submicro OCP/Gel composite exhibits similar osteoconductivity as observed in other OCP-based materials previously reported and could be used as a bone substitute material for repairing various defects in bone.

Characterization and bioactivity of nano-submicro octacalcium phosphate/gelatin composite

Energy Technology Data Exchange (ETDEWEB)

Miura, Kei-ichiro [Division of Craniofacial Function Engineering, Tohoku University Graduate School of Dentistry, Sendai (Japan); Division of Oral and Maxillofacial Surgery, Tohoku University Graduate School of Dentistry, Sendai (Japan); Anada, Takahisa; Honda, Yoshitomo [Division of Craniofacial Function Engineering, Tohoku University Graduate School of Dentistry, Sendai (Japan); Shiwaku, Yukari [Division of Craniofacial Function Engineering, Tohoku University Graduate School of Dentistry, Sendai (Japan); Division of Advanced Prosthetic Dentistry, Tohoku University Graduate School of Dentistry, Sendai (Japan); Kawai, Tadashi; Echigo, Seishi; Takahashi, Tetsu [Division of Oral and Maxillofacial Surgery, Tohoku University Graduate School of Dentistry, Sendai (Japan); Suzuki, Osamu, E-mail: suzuki-o@m.tohoku.ac.jp [Division of Craniofacial Function Engineering, Tohoku University Graduate School of Dentistry, Sendai (Japan)

2013-10-01

The present study was designed to investigate the physicochemical and bioactive properties of a nano-submicro sized octacalcium phosphate (OCP)-dispersed gelatin (Gel) composite (nano-submicro OCP/Gel) used as a bone substitute material in various bone defects. Well-grown, synthesized OCP was mechanically ground from 100 to 300 μm-sieved granules to particles that were approximately 500 nm in size. Then, 50 wt% of the nano-submicro OCP was mixed with porcine skin-derived acid extracted gelatin. The mixture was molded and lyophilized and then subjected to dehydrothermal crosslinking. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy showed that the structure of OCP was retained even after mechanical grinding to a nano-submicro scale level as well as inclusion in the Gel matrix. The bioactivity of nano-submicro OCP/Gel was examined by immersing the composite in simulated body fluid (SBF) for 7 days and by implanting it in rat critical-sized calvaria defects for 8 weeks. The nano-submicro OCP tended to convert to low crystalline hydroxyapatite (HA) in SBF as assessed by XRD. The nano-submicro OCP/Gel exhibited osteoconductivity in vivo, yielding new bone formation that was closely associated with the implanted composite. These results suggest that the nano-submicro OCP/Gel composite exhibits similar osteoconductivity as observed in other OCP-based materials previously reported and could be used as a bone substitute material for repairing various defects in bone.

Analysis of Cement-Based Pastes Mixed with Waste Tire Rubber

Science.gov (United States)

Sola, O. C.; Ozyazgan, C.; Sayin, B.

2017-03-01

Using the methods of thermal gravimetry, differential thermal analysis, Furier transform infrared analysis, and capillary absorption, the properties of a cement composite produced by introducing waste tyre rubber into a cement mixture were investigated. It was found that the composite filled with the rubber had a much lower water absorption ability than the unfilled one.

Migration of strontium, cesium, and europium from poly(butyl acrylate)/phosphate/composites prepared using gamma radiation

Energy Technology Data Exchange (ETDEWEB)

Alhassanieh, O., E-mail: cscientific@aec.org.s [Nuclear and Radiochemistry Division, Chemistry Department, Atomic Energy Commission of Syria, Damascus, P.O. Box 6091 (Syrian Arab Republic); Ajji, Z. [Polymer Technology Division, Radiation Technology Department, Atomic Energy Commission of Syria, Damascus, P.O. Box 6091 (Syrian Arab Republic); Alkourdi, H.; Haloum, D. [Nuclear and Radiochemistry Division, Chemistry Department, Atomic Energy Commission of Syria, Damascus, P.O. Box 6091 (Syrian Arab Republic)

2011-02-15

Composites based on natural phosphate powder and the monomer N-butyl acrylate have been prepared by means of gamma irradiation. The conversion of polymerization was followed up with respect to the irradiation dose using thermogravimetric analyzer (TGA). A total polymerization conversion was achieved by exposure of the samples to a dose of 10 kGy. A thermomechanical analyzer (TMA) was used to locate the region of the glass transition temperatures (T{sub g}) using the mode with alternative variable force; the mode with constant force was used to determine the T{sub g} of the pure polymer and the composite prepared at the same irradiation dose. The T{sub g} of the pure poly(butyl acrylate) is -51.41 {sup o}C, and the T{sub g} of poly(butyl acrylate)/phosphate/composites is -46.54 {sup o}C. The distribution of {sup 137}Cs, {sup 152}Eu, and {sup 85}Sr in a solid-aqueous system, a composite of phosphate-polybutyl acrylate in contact with groundwater, was investigated using {gamma}-spectrometry. The effect of contact time, pH, and the concentration of concurrent elements (Na, Ca, and La) were studied. The results were compared with earlier results with phosphate alone in the solid phase. The ability of the produced composites to keep the studied radioisotopes in the solid phase is much higher than mineral phosphate. This improvement is more remarkable by strontium and cesium than europium, due to its high element ratio in the solid phase in phosphate experiments.

A novel approach in preparing polymer/nano-CaCO3 composites

Institute of Scientific and Technical Information of China (English)

Zhengying LIU; Runze YU; Mingbo YANG; Jianmin FENG; Wei YANG; Bo YIN

2008-01-01

An novel compounding process using nano-CaCO3 aqueous suspension for preparing polymer/ nano-CaCO3 composites with nanoparticles dispersed at the nanoscale is reported. The process is called the mild mixing method. In this method, the pre-dispersed nano-particle suspensions are blended with melting polymers in a weak shearing field using an extruder, followed by removing the water from the vent. The four typical poly-meric nanocomposites were prepared by mild mixing method. The dispersion of nano-CaCO3 in the matrix of the polymer at the nanoscale was confirmed by scanning electron microscopy (SEM). The molecular weights of polycarbonate (PC) and its nanocomposite showed that the degradation had not occurred during the mild mixing processing. The mechanical properties of the composite with 1.5 wt-% nano-CaCO3 improve slightly. It proved that this approach is suitable for the preparation of nano-composites based on both polar and non-polar polymers.

Structural, Magnetic, and Transport Properties of Polymer-Nano ferrite Composites

International Nuclear Information System (INIS)

Imam, N.G.G.

2013-01-01

In this work, a series of (x) BaTiO 3 / (1-x) Ni 0.5 Zn 0.5 Fe 2 O 4 nano composite samples were prepared using citrate auto combustion and the samples were classified into three groups.In first group: A series of (x) BaTiO 3 / (1-x) Ni 0.5 Zn 0.5 Fe 2 O 4 ; 0.0≤ x ≤ 1.0 were prepared by double sintering technique and citrate auto combustion method in comparison study due to different characterization analysis. The comparison reveals that from X-ray diffraction; all the samples from the two methods formed in single phase in both; cubic spinel structure NiZnFe 2 O 4 (NZF) ferrite and perovskite tetragonal structure BaTiO 3 (BTO).In group two, in another compassion, multiferroic hybrid nano composites based on different polymers as a matrix for the prepared magnetoelectric biferroic nano composite system 0.5 BaTiO 3 / 0.5Ni 0.5 Zn 0.5 Fe 2 O 4 that has been prepared by citrate auto combustion method. Four different polymers namely poly aniline (PANI), polyvinyl acetate (PVAc), Polyvinyl pyrrolidone (PVP), and polyethylene glycol (PEG), with fixed ration (1:1) with respect to the dispersed magnetoelectric nano composite.In group three, the nano composites materials with formula (1-y) [0.5 BaTiO 3 / 0.5 Ni 0.5 Zn 0.5 Fe 2 O 4 ] / (y) (PEG); 0.0 ≤y ≤+ 1.0, have been prepared at room temperature by weight mixing and cold pressing. Physical properties of nano composite materials consisting different ratios of polyethylene glycol were investigated. With the variation of y content, typical magnetic hysteresis loops of nano composites have been observed in the nano composites at room temperature. When PEG content increase, the saturation magnetization decrease. Meanwhile, the coercive force tends to stable. Additionally, the dielectric constant (ε ' ) and dielectric loss factor (ε '' ) of nano composites materials shift toward higher frequency. The value of (ε ' ) decreased with increasing frequency, which indicates that the major contribution

Influence of gamma and e-beam irradiation on microhardness of recycled polyolefin-rubber composites

International Nuclear Information System (INIS)

Atabaev, B.G.; Gafurov, U.G.; Fainleib, A.M.; Tolstov, A.

2006-01-01

Full text: The dose dependencies of surface Vickers microhardness (H) for gamma and e-beam irradiated (E=5 MeV) recycled polyethylene-rubber and polypropylene-rubber composites has been investigated. The new techniques for measuring of polymer surface microhardness using decoration of indenter imprint under load lower 100g are developed. The measurements under 50g load shown the microhardness sharp decreasing for e-beam irradiation up to dose 50-150 kGy. The optimal dose D opt for improving of viscoelastic properties at minimal microhardness HV for HDPE-rubber blends-100 kGy and PP-rubber blends-75 kGy are defined. The microhardness change depend on irradiation dose can be explained by concurrence of irradiation stimulated chain cross-linking, oxidation and destruction processes. In our work samples of polyolefin powder were irradiated in air to form peroxide and hydroperoxide groups and heated to form polar groups capable of improving the compatibility with the radiation devulcanized rubber particles. The absolute value of microhardness of polyolefin-rubber composites extremely low for polyolefins and close to microhardness of high elastic rubber. The viscoelastic properties can be explained by new model of formation mixing amorphous interface between semicrystalline polyolefin and devulcanized rubber. The work was supported by EC (STCU Project U3009). (author)

Thermal, Morphological and Physic-Mechanical Properties of Natural Rubber - CaCO3 Composites Using Jatropha Oil as Softener.

Directory of Open Access Journals (Sweden)

Nasruddin

2018-01-01

Full Text Available The urgency of green technology in rubber compounding has become a critical issue recently. In this research, the effect of using renewable resources in rubber compounding has been studied. Commercial Calcium Carbonate, Silica and Jatropha Oil were used in natural rubber composite. The research was designed by varying the types of commercial filler namely CaCO3 (47-51 phr, silica (47-51 phr and Jatropha Oil (4-6 phr in natural rubber composites (SIR-20. The formulas were intentionally designed for rubber tips vulcanizates. The samples were characterized by the determination of physic-mechanical, thermal (TGA and morphological (SEM properties. From the measured results, there is no significant effect on the tensile strength, specific gravity, and hardness on the loading of commercial CaCO3 and Silica in natural rubber composites using Jatropha Oil. However, a slight difference in elongation at break and abrasion resistance could be detected. Compared to the commercial rubber tips, the rubber tips produced in this research have higher tensile strength, elongation at break and abrasion resistance. Due to the usage of commercial CaCO3 and Silica, the SEM micrographs show rough surface because of the agglomeration. The thermogram shows clearly the compositional analysis of the rubber tips vulcanizates consist of Jatropha Oil and natural rubber, CaCO3, ash and other filler residues such as Silica.

Impact behavior of f-silica and amine terminated polybutadiene co-acrylonitrile rubber modified novolac epoxy/Kevlar nanocomposites

Science.gov (United States)

Kavita, Pal, Vijayeta; Tiwari, R. K.

2018-05-01

In the present work, nano-fumed silica treated with 3-Glycidoxypropyl trimethoxy silane (f-silica) was used as a nanoreinforcement in the fabrication of amine terminated polybutadiene co-acrylonitrile rubber (ATBN) modified Kevlar/epoxy based nanocomposites. Nanocomposites with different f-silica loading (0, 0.5, 1.0 and 2.0 wt. %) and having same ATBN (10 wt. %) were made and characterized by Izod impact test for evaluating impact strength values. All the nanocomposites showed better impact strength than neat Kevlar/novolac epoxy based composite.

Mechanical properties of hexaferite based magnet composite of SrFe12019 and BaFe12O19 with natural rubber bonding agent

International Nuclear Information System (INIS)

Waluyo, T.; Herman, Y.A.; Sudirman; Ridwan

2000-01-01

Research on mechanical properties at magnet composite of SrFe 12 0 19 (SrM) and BaFe 12 O 19 (BaM)magnet powder with natural rubber bonding agent have been done. The natural rubber used was rubber made of latex without vulcanization, The SrM powder having average particle size of 1.6 μm and flat shaped. and the BaM powder having particle size of 1.2 μm and nodular shaped. The production of composite carried out in Labo Plastomill at 100 o C and mixer speed of 30 rpm for 7 minutes. The result obtained from Labo Plastomill then made into sheets. Mechanical properties of the composite tested were strain, elongation break and hardness, The results showed that the highest strain of the SrM composite obtained at composition of 70% vol of powder that is 2,22 MPa, and 3,84 MPa for BaM composite at 50% vol. of powder The elongation break of SrM composite decreased by increasing of powder volume fraction, that is 90% at the composition or 70% vol. of powder, and 370% for BaM composite at 50% vol. fraction of powder. The highest hardness for SrM composite obtained at composition of of 70% vol. of powder, that is 95 SHA. and for the BaM composite at 50% vol. of powder. that is 52 SHA

Hevea brasiliensis natural rubber latex film vulcanization by gamma radiation containing n-butyl acrylate: properties and morphology; Filme de latex de borracha natural de Hevea brasiliensis vulcanizado por radiacao gama contendo acrilato de n-butila: propriedades e morfologia

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Ana Paula Pinho; Barros, Glaucione Gomes de [Brasilia Univ., DF (Brazil). Dept. de Quimica; Guedes, Selma M.L. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

1997-07-01

Radiation vulcanization of natural rubber latex (RVNRL) in the presence of n-butyl acrylate (n-Ba) as sensitizer was carried out. The RVNRL films were investigated with respect to their thermal properties and morphology. The films presented two T{sub g} values obtained by DSC which were identified as due to linear and crosslinked domains. The thermal stability of the material was similar to that of linear material rubber. The morphology showed smooth regular surface characteristic of homogeneous phase domains. (author)

Investigating the tension load of rubber composites by impact ...

Indian Academy of Sciences (India)

This work deals with establishing the tension load by impact dynamic testing of rubber composite con- veyor belts. ... top layer ('top cover'), a fabric carcass which provide tensile strength, skim ... components of machines like CBs [20]. CBs of ...

Studies on Effective Elastic Properties of CNT/Nano-Clay Reinforced Polymer Hybrid Composite

Science.gov (United States)

Thakur, Arvind Kumar; Kumar, Puneet; Srinivas, J.

2016-02-01

This paper presents a computational approach to predict elastic propertiesof hybrid nanocomposite material prepared by adding nano-clayplatelets to conventional CNT-reinforced epoxy system. In comparison to polymers alone/single-fiber reinforced polymers, if an additional fiber is added to the composite structure, it was found a drastic improvement in resultant properties. In this regard, effective elastic moduli of a hybrid nano composite are determined by using finite element (FE) model with square representative volume element (RVE). Continuum mechanics based homogenization of the nano-filler reinforced composite is considered for evaluating the volumetric average of the stresses and the strains under different periodic boundary conditions.A three phase Halpin-Tsai approach is selected to obtain the analytical result based on micromechanical modeling. The effect of the volume fractions of CNTs and nano-clay platelets on the mechanical behavior is studied. Two different RVEs of nano-clay platelets were used to investigate the influence of nano-filler geometry on composite properties. The combination of high aspect ratio of CNTs and larger surface area of clay platelets contribute to the stiffening effect of the hybrid samples. Results of analysis are validated with Halpin-Tsai empirical formulae.

Compression properties and dissolution of bioactive glass S53P4 and n-butyl-2 cyanoacrylate tissue adhesive-composite.

Science.gov (United States)

Sarin, Jussi; Hiltunen, Markus; Hupa, Leena; Pulkkinen, Jaakko; Vallittu, Pekka K

2016-09-28

Bioactive glass (BG)-containing fiber-reinforced composite implants, typically screw-retained, have started to be used clinically. In this study, we tested the mechanical strength of composites formed by a potential implant adhesive of n-butyl-2-cyanoacrylate glue and BG S53P4 particles. Water immersion for 3, 10 or 30 days had no adverse effect on the compression strength. When cyanoacrylate glue-BG-composites were subjected to simulated body fluid immersion, the average pH rose to 7.52 (SD 0.066) from the original value of 7.35 after 7 days, and this pH increment was smaller compared to BG particle-group or fibrin glue-BG-composite group. Based on these results n-butyl-2 cyanoacrylate glue, by potentially producing a strong adhesion, might be considered a possible alternative for fixation of BG S53P4 containing composite implants. However, the mechanical and solubility properties of the cyanoacrylate glue may not encourage the use of this tissue adhesive with BG particles.

Study on the structure-properties relationship of natural rubber/SiO2 composites modified by a novel multi-functional rubber agent

Directory of Open Access Journals (Sweden)

S. Y. Yang

2014-06-01

Full Text Available Vulcanization property and structure-properties relationship of natural rubber (NR/silica (SiO2 composites modified by a novel multi-functional rubber agent, N-phenyl- N'-(γ-triethoxysilane-propyl thiourea (STU, are investigated in detail. Results from the infrared spectroscopy (IR and X-ray photoelectron spectroscopy (XPS show that STU can graft to the surface of SiO2 under heating, resulting in a fine-dispersed structure in the rubber matrix without the connectivity of SiO2 particles as revealed by transmission electron microscopy (TEM. This modification effect reduces the block vulcanization effect of SiO2 for NR/SiO2/STU compounds under vulcanization process evidently. The 400% modulus and tensile strength of NR/SiO2/STU composites are much higher than that of NR/SiO2/TU composites, although the crystal index at the stretching ratio of 4 and crosslinking densities of NR/SiO2 composites are almost the same at the same dosage of SiO2. Consequently, a structure-property relationship of NR/SiO2/STU composites is proposed that the silane chain of STU can entangle with NR molecular chains to form an interfacial region, which is in accordance with the experimental observations quite well.

Density functional theory studies on the nano-scaled composites consisted of graphene and acyl hydrazone molecules

Science.gov (United States)

Ren, J. L.; Zhou, L.; Lv, Z. C.; Ding, C. H.; Wu, Y. H.; Bai, H. C.

2016-07-01

Graphene, which is the first obtained single atomic layer 2D materials, has drawn a great of concern in nano biotechnology due to the unique property. On one hand, acyl hydrazone compounds belonging to the Schif bases have aroused considerable attention in medicine, pharmacy, and analytical reagent. However, few understanding about the interaction between graphene and acyl hydrazone molecules is now available. And such investigations are much crucial for the applications of these new nano-scaled composites. The current work revealed theoretical investigations on the nano-scaled composites built by acyl hydrazone molecules loaded on the surface of graphene. The relative energy, electronic property and the interaction between the counterparts of graphene/acyl hydrazone composites are investigated based on the density functional theory calculations. According to the obtained adsorption energy, the formation of the nano-scaled composite from the isolated graphene and acyl hydrazone molecule is exothermic, and thus it is energetically favorable to form these nano composites in viewpoint of total energy change. The frontier molecular orbital for the nano composite is mainly distributed at the graphene part, leading to that the energy levels of the frontier molecular orbital of the nano composites are very close to that of isolated graphene. Moreover, the counterpart interaction for the graphene/acyl hydrazone composites is also explored based on the discussions of orbital hybridization, charge redistribution and Van der Waals interaction.

Improving Thermo-Oxidative Stability of Nitrile Rubber Composites by Functional Graphene Oxide.

Science.gov (United States)

Zhong, Rui; Zhang, Zhao; Zhao, Hongguo; He, Xianru; Wang, Xin; Zhang, Rui

2018-05-30

Graphene oxide (GO), modified with anti-aging agent p -phenylenediamine (PPD), was added into nitrile rubber (NBR) in order to improve the thermo-oxidative stability of NBR. The modification of GO and the transformation of functional groups were characterized by Fourier transform infrared spectroscopy (FTIR), Raman, and X-ray diffraction (XRD). Mechanical performances of NBR composites before and after the thermo-oxidative aging were recorded. The results of dynamic mechanical analysis (DMA) show an increased storage modulus (G') and a decreased value of area of tan δ peak after introducing modified GO into NBR. It indicates that filler particles show positive interaction with molecular chains. The thermo-oxidative stability of composites was investigated by thermogravimetric analysis (TG) and differential scanning calorimetry (DSC). Then, the thermo-oxidative aging kinetic parameters were obtained by the Flynn⁻Wall⁻Ozawa (FWO) equation. The results of aging tests show that the thermo-oxidative stability of rubber matrix increases obviously after introducing GO⁻PPD. In addition, mechanical properties (tensile strength and elongation at break) of both before and after aged NBR/GO⁻PPD composites were superior to that of NBR. This work provides meaningful guidance for achieving multifunction thermo-oxidative aging resistance rubber composites.

Fabrication and mechanical evaluation of hydroxyapatite/oxide nano-composite materials.

Science.gov (United States)

Mohamed, Khaled R; Beherei, Hanan H; El Bassyouni, Gehan T; El Mahallawy, Nahed

2013-10-01

In the current study, the semiconducting metal oxides such as nano-ZnO and SiO2 powders were prepared via sol-gel technique and conducted on nano-hydroxyapatite (nHA) which was synthesized by chemical precipitation. The properties of fabricated nano-structured composites containing different ratios of HA, ZnO and SiO2 were examined using X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscope (SEM) and transmission electron microscope (TEM) techniques. The effect of the variation of ratios between the three components on mechanical, microstructure and in-vitro properties was assessed to explore the possibility of enhancing these properties. The results proved that the mechanical properties exhibited an increment with increasing the ZnO content at the extent of HA. In-vitro study proved the formation and nucleation of apatite onto the surface of the fabricated composites after one week of immersion. It is concluded that HA composites containing SiO2 or SiO2/ZnO content had a suitable mechanical properties and ability to form apatite particles onto the composite surface. Based on bioactivity behavior, Si-HA is more bioactive than pure hydroxyapatite and nano-arrangements will provide an interface for better bone formation. Therefore, these nano-composites will be promising as bone substitutes especially in load bearing sites. Copyright © 2013 Elsevier B.V. All rights reserved.

Development and Characterization of Polymer Eco-Composites Based on Natural Rubber Reinforced with Natural Fibers.

Science.gov (United States)

Stelescu, Maria-Daniela; Manaila, Elena; Craciun, Gabriela; Chirila, Corina

2017-07-11

Natural rubber composites filled with short natural fibers (flax and sawdust) were prepared by blending procedure and the elastomer cross-linking was carried out using benzoyl peroxide. The microbial degradation of composites was carried out by incubating with Aspergillus niger recognized for the ability to grow and degrade a broad range of substrates. The extent of biodegradation was evaluated by weight loss and cross-linking degree study of composites after 2 months incubation in pure shake culture conditions. Scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FT-IR) have proved to be precious and valuable instruments for morphological as well as structural characterization of the composites before and after incubation with Aspergillus niger .

Development and Characterization of Polymer Eco-Composites Based on Natural Rubber Reinforced with Natural Fibers

Directory of Open Access Journals (Sweden)

Maria-Daniela Stelescu

2017-07-01

Full Text Available Natural rubber composites filled with short natural fibers (flax and sawdust were prepared by blending procedure and the elastomer cross-linking was carried out using benzoyl peroxide. The microbial degradation of composites was carried out by incubating with Aspergillus niger recognized for the ability to grow and degrade a broad range of substrates. The extent of biodegradation was evaluated by weight loss and cross-linking degree study of composites after 2 months incubation in pure shake culture conditions. Scanning electron microscopy (SEM and Fourier transform infrared spectroscopy (FT-IR have proved to be precious and valuable instruments for morphological as well as structural characterization of the composites before and after incubation with Aspergillus niger.

Fabrication of Nano-CeO2 and Application of Nano-CeO2 in Fe Matrix Composites

International Nuclear Information System (INIS)

Tiebao, W.; Chunxiang, C.; Xiaodong, W.; Guobin, L.

2010-01-01

It is expatiated that nano-CeO2 is fabricated by the direct sedimentation method. The components and particles diameter of nano-CeO2 powders are analyzed by XRD and SEM . The thermodynamic analysis and acting mechanism of nano-CeO2 with Al in Fe matrix composites are researched, which shows that the reaction is generated between CeO2 and Al in the composite, that is, 3CeO2+4Al - 2Al2O3+3[Ce], which obtains Al2O3 and active [Ce] during the sintering process. The active [Ce] can improve the performance of CeO2/Fe matrix composites. The suitable amount of CeO2 is about 0.05% in CeO2/Fe matrix composites. SEM fracture analysis shows that the toughness sockets in nano-CeO2/Fe matrix composites are more than those in no-added nano-CeO2 composites, which can explain that adding nano-CeO2 into Fe matrix composite, the toughness of the composite is improved significantly. Applied nano-CeO2 to Fe matrix diamond saw blades shows that Fe matrix diamond saw blade is sharper and of longer cutting life than that with no-added nano-CeO2.

Preparation and properties of natural nanocomposites based on natural rubber and naturally occurring halloysite nanotubes

International Nuclear Information System (INIS)

Rooj, Sandip; Das, Amit; Thakur, Varun; Mahaling, R.N.; Bhowmick, Anil K.; Heinrich, Gert

2010-01-01

A 'green' composite based on natural halloysite nanotubes (HNTs) and natural rubber (NR) was prepared by mechanical mixing. A silane coupling agent, bis (triethoxysilylpropyl)-tetrasulphide, was utilized to enhance the properties of these composites. It was observed that the reinforcing activity of HNTs was superior to commercial silica coupled with the same amount of silane coupling agent. Moreover the on-set thermal degradation decomposition temperature was improved by ∼64 o C with the addition of 10 parts HNTs per hundred of rubber. Transmission electron microscopic images confirmed the good dispersion of the HNTs in the rubber matrix, whereas X-ray diffraction studies showed a little change in interlayer spacing between the two silicate layers of HNTs.

TLC/IR (UATR) off-line coupling for the characterization of additives in EPDM rubber compositions

OpenAIRE

Denis Damazio; Eunice Aparecida Campos; Milton Faria Diniz; Elizabeth da Costa Mattos; Rita de Cássia Lazzarini Dutra

2016-01-01

Abstract The knowledge of the components that constitutes a rubber composition is important to justify the properties of the final device, particularly when it comes to elastomeric compositions used in the aerospace industry. The development of methodologies that can detect components, specially the smallest proportion of the rubbers composition is a constant challenge and an important gap in the studies of this nature. Therefore, methodologies by using standard techniques and/or of last gene...

Mechanical Properties of Medium Density Fibreboard Composites Material Using Recycled Rubber and Coconut Coir

OpenAIRE

S. Mahzan; A.M. Ahmad Zaidi; M.I. Ghazali; N. Arsat; M.N. M. Hatta

2010-01-01

Natural fibre reinforced composite has emerged as highly potential replacement for synthetic fibres. Various natural waste fibres have been adopted for various engineering applications. This paper investigates the mechanical properties of medium density fibreboard composites material fabricated using recycled rubber and coconut coir. The suitability of using recycled rubber and coconut coir as a raw material and polyurethane as a resin in the manufacturer of medium density fibreboard was also...

Study of Ion Transport Behaviour in (PVA-NH4I):SIO2 Nano Composite Polymer Electrolyte

Science.gov (United States)

Tripathi, Mridula; Trivedi, Shivangi; Upadhyay, Ruby; Singh, Markandey; Pandey, N. D.; Pandey, Kamlesh

2013-07-01

Development and characterization of Poly vinyl alcohol (PVA) based nano composite polymer electrolytes comprising of (PVA-NH4I):SiO2 is reported. Sol-gel derived silica powder of nano dimension has been used as ceramic filler for development of nano composite electrolyte. Formation of nano composites, change in the structural and microscopic properties of the system have been investigated by X-ray differaction, SEM and conductivity.

Lifetime Prediction of Nano-Silica based Glass Fibre/Epoxy composite by Time Temperature Superposition Principle

Science.gov (United States)

Anand, Abhijeet; Banerjee, Poulami; Prusty, Rajesh Kumar; Ray, Bankin Chandra

2018-03-01

The incorporation of nano fillers in Fibre reinforced polymer (FRP) composites has been a source of experimentation for researchers. Addition of nano fillers has been found to improve mechanical, thermal as well as electrical properties of Glass fibre reinforced polymer (GFRP) composites. The in-plane mechanical properties of GFRP composite are mainly controlled by fibers and therefore exhibit good values. However, composite exhibits poor through-thickness properties, in which the matrix and interface are the dominant factors. Therefore, it is conducive to modify the matrix through dispersion of nano fillers. Creep is defined as the plastic deformation experienced by a material for a temperature at constant stress over a prolonged period of time. Determination of Master Curve using time-temperature superposition principle is conducive for predicting the lifetime of materials involved in naval and structural applications. This is because such materials remain in service for a prolonged time period before failure which is difficult to be kept marked. However, the failure analysis can be extrapolated from its behaviour in a shorter time at an elevated temperature as is done in master creep analysis. The present research work dealt with time-temperature analysis of 0.1% SiO2-based GFRP composites fabricated through hand-layup method. Composition of 0.1% for SiO2nano fillers with respect to the weight of the fibers was observed to provide optimized flexural properties. Time and temperature dependence of flexural properties of GFRP composites with and without nano SiO2 was determined by conducting 3-point bend flexural creep tests over a range of temperature. Stepwise isothermal creep tests from room temperature (30°C) to the glass transition temperature Tg (120°C) were performed with an alternative creep/relaxation period of 1 hour at each temperature. A constant stress of 40MPa was applied during the creep tests. The time-temperature superposition principle was

Flame Retardant Effect of Nano Fillers on Polydimethylsiloxane Composites.

Science.gov (United States)

Jagdale, Pravin; Salimpour, Samera; Islam, Md Hujjatul; Cuttica, Fabio; Hernandez, Francisco C Robles; Tagliaferro, Alberto; Frache, Alberto

2018-02-01

Polydimethylsiloxane has exceptional fire retardancy characteristics, which make it a popular polymer in flame retardancy applications. Flame retardancy of polydimethylsiloxane with different nano fillers was studied. Polydimethylsiloxane composite fire property varies because of the shape, size, density, and chemical nature of nano fillers. In house made carbon and bismuth oxide nano fillers were used in polydimethylsiloxane composite. Carbon from biochar (carbonised bamboo) and a carbon by-product (carbon soot) were selected. For comparative study of nano fillers, standard commercial multiwall carbon nano tubes (functionalised, graphitised and pristine) as nano fillers were selected. Nano fillers in polydimethylsiloxane positively affects their fire retardant properties such as total smoke release, peak heat release rate, and time to ignition. Charring and surface ceramization are the main reasons for such improvement. Nano fillers in polydimethylsiloxane may affect the thermal mobility of polymer chains, which can directly affect the time to ignition. The study concludes that the addition of pristine multiwall carbon nano tubes and bismuth oxide nano particles as filler in polydimethylsiloxane composite improves the fire retardant property.

Correlation of Electrical and Swelling Properties with Nano Free Volume Structure of Conductive Silicone Rubber Composites

International Nuclear Information System (INIS)

Abd-El Salam, M.H.; El-Gamal, S.; Abd El-Maqsoud, D.M.; Mohsen, M.

2013-01-01

The present study focuses on finding a correlation between the positron annihilation parameters in silicone rubber based on Poly dimethyl siloxane (PDMS) composites loaded with different conductive fillers and their swelling and electrical properties. Four types of conductive fillers have been used in this study: carbon black, graphite, copper, and nickel powders. The maximum degree of swelling Q m %, the penetration rate, P, as well as the diffusion coefficient, D, decrease with increasing the filler content due to the reduction of the size of free volume, as observed through a decrease of the probability of ortho-positronium (o-Ps) formation I 3 and the o-Ps lifetime Τ 3 , representing the size of free volume measured by the positron annihilation lifetime technique (PAL). The electrical conductivity ln (Σ) is positively correlated with the probability of free annihilation of positrons at interfaces I 2 , thus suggesting an increase in the electron density with the filler content. The activation energy of conduction, E a , is found to decrease with the increase in the loading of conductive filler and the particle size of the filler. A correlation between the free-volume V f , and the d.c. electrical conductivity ln (Σ) is found to be in accordance with Miyamoto and Shibayma model of ion conduction.

Graphene/Gold Nano composites-Based Thin Films as an Enhanced Sensing Platform for Voltammetric Detection of Cr(VI) Ions

International Nuclear Information System (INIS)

Santhosh, Ch.; Saranya, M.; Ramachandran, R.; Felix, S.; Velmurugan, V.; Grace, A.N.

2014-01-01

A highly sensitive and selective Cr(VI) sensor with graphene-based nano composites film as an enhanced sensing platform is reported. The detection of chromium species is a challenging task because of the different possible oxidation states in which the element can occur. The sensing film was developed by homogeneously distributing Au nanoparticles (AuNPs) onto the two-dimensional (2D) graphene nano sheet matrix by electrochemical method. Such nano structured composite film platforms combine the advantages of AuNPs and graph ene nano sheets because of the synergistic effect between them. This effect greatly facilitates the electron-transfer processes and the sensing behavior for Cr(VI) detection, leading to a remarkably improved sensitivity and selectivity. The interference from other heavy metal ions is studied in detail. Such sensing elements are very promising for practical environmental monitoring applications.

Novel mesoporous composites based on natural rubber and hexagonal mesoporous silica: Synthesis and characterization

Energy Technology Data Exchange (ETDEWEB)

Nuntang, Sakdinun; Poompradub, Sirilux [Fuels Research Center, Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand); Butnark, Suchada [PTT Research and Technology Institute, PTT Public Company Limited, Wangnoi, Ayutthaya 13170 (Thailand); Yokoi, Toshiyuki; Tatsumi, Takashi [Division of Catalytic Chemistry, Chemical Resources Laboratory, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8503 (Japan); Ngamcharussrivichai, Chawalit, E-mail: Chawalit.Ng@Chula.ac.th [Fuels Research Center, Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand); Center of Excellence on Petrochemical and Materials Technology (PETROMAT), Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand)

2014-02-14

The present study is the first report on the synthesis and characterization of mesoporous composites based on natural rubber (NR) and hexagonal mesoporous silica (HMS). A series of NR/HMS composites were prepared in tetrahydrofuran via an in situ sol–gel process using tetraethylorthosilicate as the silica precursor. The physicochemical properties of the composites were characterized by various techniques. The effects of the gel composition on the structural and textural properties of the NR/HMS composites were investigated. The Fourier-transform infrared spectroscopy (FTIR) and {sup 29}Si magic angle spinning nuclear magnetic resonance ({sup 29}Si MAS NMR) results revealed that the surface silanol groups of NR/HMS composites were covered with NR molecules. The powder X-ray diffraction (XRD) and transmission electron microscopy (TEM) data indicated an expansion of the hexagonal unit cell and channel wall thickness due to the incorporation of NR molecules into the mesoporous structure. NR/HMS composites also possessed nanosized particles (∼79.4 nm) as confirmed by scanning electron microscopy (SEM) and particle size distribution analysis. From N{sub 2} adsorption–desorption measurement, the NR/HMS composites possessed a high BET surface area, large pore volume and narrow pore size distribution. Further, they were enhanced hydrophobicity confirmed by H{sub 2}O adsorption–desorption measurement. In addition, the mechanistic pathway of the NR/HMS composite formation was proposed. - Highlights: • NR molecules were incorporated into hexagonal meso-structure of HMS. • NR/HMS composites exhibited an expanded unit cell and channel wall thickness. • Nanosized NR/HMS composites with a lower particle size range were obtained. • NR/HMS had high surface area, large pore volume and narrow pore size distribution. • NR/HMS composites displayed an enhanced hydrophobicity.

Improving Thermo-Oxidative Stability of Nitrile Rubber Composites by Functional Graphene Oxide

Directory of Open Access Journals (Sweden)

Rui Zhong

2018-05-01

Full Text Available Graphene oxide (GO, modified with anti-aging agent p-phenylenediamine (PPD, was added into nitrile rubber (NBR in order to improve the thermo-oxidative stability of NBR. The modification of GO and the transformation of functional groups were characterized by Fourier transform infrared spectroscopy (FTIR, Raman, and X-ray diffraction (XRD. Mechanical performances of NBR composites before and after the thermo-oxidative aging were recorded. The results of dynamic mechanical analysis (DMA show an increased storage modulus (G’ and a decreased value of area of tan δ peak after introducing modified GO into NBR. It indicates that filler particles show positive interaction with molecular chains. The thermo-oxidative stability of composites was investigated by thermogravimetric analysis (TG and differential scanning calorimetry (DSC. Then, the thermo-oxidative aging kinetic parameters were obtained by the Flynn–Wall–Ozawa (FWO equation. The results of aging tests show that the thermo-oxidative stability of rubber matrix increases obviously after introducing GO–PPD. In addition, mechanical properties (tensile strength and elongation at break of both before and after aged NBR/GO–PPD composites were superior to that of NBR. This work provides meaningful guidance for achieving multifunction thermo-oxidative aging resistance rubber composites.

Proceedings of the international symposium on radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Machi, Sueo

1990-01-01

The First International Symposium on Radiation Vulcanization of Natural Rubber Latex (RVNRL) was held from 26 to 28 July 1989 at Tokyo and Takasaki. In these proceedings, thirty six papers presented at the Symposium are compiled. Main topics are commercial application of RVNRL, characterization of NR latex and vulcanization, properties of radiation vulcanized NR latex, development of sensitizers, mechanism of RVNRL, RVNRL with electron beams, and new Co-60 irradiator for RVNRL. Absence of nitrosamines and low cytotoxicity of radiation vulcanized NR latex are recognized as the remarkable advantages of RVNRL. The radiation vulcanization process for the production of protective rubber gloves for radioactive contamination was presented as the first commercial success in RVNRL. It was reported that various kinds of rubber articles for medical uses have being developed in West Germany. A sensitizer system consisting of n-butyl acrylate and t-butyl hydroperoxide was found to reduce the vulcanization dose to 8 kGy. (author)

Mechanical Behavior of Polymer Nano Bio Composite for Orthopedic Implants

Science.gov (United States)

Marimuthu, K., Dr.; Rajan, Sankar

2018-04-01

The bio-based polymer composites have been the focus of many scientific and research projects, as well as many commercial programs. In recent years, scientists and engineers have been working together to use the inherent strength and performance of the new class of bio-based composites which is compactable with human body and can act as a substitute for living cells. In this stage the polymer composites also stepped into human bone implants as a replacement for metallic implants which was problems like corrosion resistance and high cost. The polymer composite have the advantage that it can be molded to the required shape, the polymers have high corrosion resistance, less weight and low cost. The aim of this research is to develop and analyze the suitable bio compactable polymer composite for human implants. The nano particles reinforced polymer composites provides good mechanical properties and shows good tribological properties especially in the total hip and knee replacements. The graphene oxide powders are bio compactable and acts as anti biotic. GO nano powder where reinforced into High-density polyethylene in various weight percentage of 0.5% to 2%. The performance of GO nano powder shows better tribological properties. The material produced does not cause any pollution to the environment and at the same time it can be bio compactable and sustainable. The product will act environmentally friendly.

Nano-Reinforcement of Interfaces in Prepreg-Based Composites Using a Carbon Nanotubes Spraying Method

KAUST Repository

Almuhammadi, Khaled

2012-01-01

of epoxy resins used as matrix materials for CFRP composites can be increased by the addition of nano-sized fillers such as Carbon nanotubes (CNTs). CNTs are particularly well suited for this purpose because of their nano-scale diameter and high aspect

Novel Techniques for Characterizing and Understanding the Response of Rubbers and Rubber-Based Composites to Impact Loading

Science.gov (United States)

2016-09-30

obtained from the drop -weight simulations at the temperature ranges from 60 to -12 °C and the given nitrile and silicone rubber relaxation curves...characterising the high rate properties of low impedance polymers. In particular, the difficulties of testing materials with low wavespeeds are...addressed using two different methods based on wave propagation: 1) Optical measurements of the evolution of displacement fields induced by stress wave

The partial replacement of palm kernel shell by carbon black and halloysite nanotubes as fillers in natural rubber composites

Science.gov (United States)

Daud, Shuhairiah; Ismail, Hanafi; Bakar, Azhar Abu

2017-07-01

The effect of partial replacement of palm kernel shell powder by carbon black (CB) and halloysite nanotube (HNT) on the tensile properties, rubber-filler interaction, thermal properties and morphological studies of natural rubber (NR) composites were investigated. Four different compositions of NR/PKS/CB and NR/PKS/HNT composites i.e 20/0, 15/5, 10/10,5/15 and 0/20 parts per hundred rubber (phr) were prepared on a two roll mill. The results showed that the tensile strength and modulus at 100% elongation (M100) and 300% elongation (M300) were higher for NR/PKS/CB compared to NR/PKS/HNT composites. NR/PKS/CB composites had the lowest elongation at break (Eb). The effect of commercial fillers in NR/PKS composites on tensile properties was confirmed by the rubber-filler interaction and scanning electron microscopy (SEM) study. The thermal stability of PKS filled NR composites with partially replaced by commercial fillers also determined by Thermo gravimetric Analysis (TGA).

Comparative studies on the mechanical properties of natural rubber and natural rubber filled with multi-walled carbon nanotubes

Science.gov (United States)

Ismail, R.; Ibrahim, A.; Rusop, M.; Adnan, A.

2018-05-01

The present article compares the mechanical properties of natural rubber (NR) and carbon nanotubes (CNTs) filled natural rubber composites. Four types of nanocomposite specimens are fabricated with different MWCNT loadings: 0 wt% (pure natural rubber), 1 wt%, 3 wt%, and 5 wt%. The specimens are tested for their mechanical properties. It is observed that the tensile strength, hardness and elongation break of CNTs filled rubber composites are remarkably higher than that of raw rubber indicating the inherent reinforcing potential of CNTs. Percentage of the elongation at break of rubber CNTs composites is lower than that of raw rubber.

Synthesis of Metal Polymer Nano composites Using Ionizing Radiation

International Nuclear Information System (INIS)

Mostafa, R.S.S.

2012-01-01

we prepared a series of CdS/PVA and Ag/PVA nano composites via facile and novel synthetic steps. Our synthetic route is simpler; it does not need expensive oxidizing agents, surfactants, templates and complicated apparatus. The present work contains five chapters in addition to the list of figures, tables, abbreviations and references. The first two chapters are concerned with the introduction and reviews of previous studies. Chapter 3 describes the preparation methodology, experimental setup and techniques used in the CdS/PVA and Ag/PVA nano composites processing and analysis. CdS and Ag nanoparticles with different particle sizes were prepared via chemical method and gamma irradiation method. Several techniques were used to detect the structural changes of the nano composites due to interaction between CdS or Ag ions and PVA. These are: UV-Visible spectrophotometer, Transmission Electron microscope (TEM), X-ray diffraction (XRD), Fourier Transform Infrared (FTIR) Spectrophotometer, and thermogravimetric analysis. Chapter 4 includes the obtained results and their discussions: Ultraviolet/Visible spectroscopy (UV/VIS) investigated that the as-prepared nano composites have improved optical properties. Such incremented optical properties were attributed to the nano scale dispersion (nm). The improvement in the optical properties is considered to be dependent on, Cd 2+ :S 2- molar ratio, Ag concentration, Pva content and irradiation dose. The calculated band gap energies for CdS/PVA nano composites are higher than that of bulk of CdS indicating the strong quantum confinement. The increases in band gap energy have been attributed to the crystalline size dependent properties. Transmission electron microscope images illustrated that the nano structured CdS/PVA films were found to be dispersed spherical nanoparticles with good structural homogeneity and polydispersity at either lower concentration of CdCl 2 and/or irradiation dose. Nano rod structure of CdS accompanied

Gold surface supported spherical liposome-gold nano-particle nano-composite for label free DNA sensing.

Science.gov (United States)

Bhuvana, M; Narayanan, J Shankara; Dharuman, V; Teng, W; Hahn, J H; Jayakumar, K

2013-03-15

Immobilization of 1,2-dioleoyl-sn-glycero-3-phosphoethanolamine (DOPE) liposome-gold nano-particle (DOPE-AuNP) nano-composite covalently on 3-mercaptopropionic acid (MPA) on gold surface is demonstrated for the first time for electrochemical label free DNA sensing. Spherical nature of the DOPE on the MPA monolayer is confirmed by the appearance of sigmoidal voltammetric profile, characteristic behavior of linear diffusion, for the MPA-DOPE in presence of [Fe(CN)(6)](3-/4-) and [Ru(NH(3))(6)](3+) redox probes. The DOPE liposome vesicle fusion is prevented by electroless deposition of AuNP on the hydrophilic amine head groups of the DOPE. Immobilization of single stranded DNA (ssDNA) is made via simple gold-thiol linkage for DNA hybridization sensing in the presence of [Fe(CN)(6)](3-/4-). The sensor discriminates the hybridized (complementary target hybridized), un-hybridized (non-complementary target hybridized) and single base mismatch target hybridized surfaces sensitively and selectively without signal amplification. The lowest target DNA concentration detected is 0.1×10(-12)M. Cyclic voltammetry (CV), electrochemical impedance (EIS), differential pulse voltammetry (DPV) and quartz crystal microbalance (QCM) techniques are used for DNA sensing on DOPE-AuNP nano-composite. Transmission Electron Microscopy (TEM), Fourier Transform Infrared Spectroscopy (FTIR), Atomic Force Microscopy (AFM), Dynamic Light Scattering (DLS) and Ultraviolet-Visible (UV) spectroscopic techniques are used to understand the interactions between the DOPE, AuNP and ssDNA. The results indicate the presence of an intact and well defined spherical DOPE-AuNP nano-composite on the gold surface. The method could be applied for fabrication of the surface based liposome-AuNP-DNA composite for cell transfection studies at reduced reagents and costs. Copyright © 2012 Elsevier B.V. All rights reserved.

Swelling behaviour of isora/natural rubber composites in oils used in ...

Indian Academy of Sciences (India)

Unknown

Department of Polymer Science and Rubber Technology, Cochin University of Science and Technology,. Kochi 682 022 ... natural resources have prompted the composite industry to .... provided information on the interface strength, degree of.

Maleic anhydride grafting on EPDM rubber in the melt

NARCIS (Netherlands)

Oostenbrink, A.J.; Oostenbrink, A.J.; Gaymans, R.J.

1992-01-01

The grafting of maleic anhydride on a EPDM rubber was studied with a twin screw extruder. The effect of barrel temperatures, throughput, maleic anhydride concentration and peroxide concentration [bis(t-butyl peroxy isopropyl)benzene] on the degree of grafting and melt viscosity was studied. The

Advances in rubber/halloysite nanotubes nanocomposites.

Science.gov (United States)

Jia, Zhixin; Guo, Baochun; Jia, Demin

2014-02-01

The research advances in rubber/halloysite nanotubes (rubber/HNTs) nanocomposites are reviewed. HNTs are environmentally-friendly natural nanomaterials, which could be used to prepare the rubber-based nanocomposites with high performance and low cost. Unmodified HNTs could be adopted to prepare the rubber/HNTs composites with improved mechanical properties, however, the rubber/HNTs nanocomposites with fine morphology and excellent properties were chiefly prepared with various modifiers by in situ mixing method. A series of rubber/HNTs nanocomposites containing several rubbers (SBR, NR, xSBR, NBR, PU) and different modifiers (ENR, RH, Si69, SA, MAA, ILs) have been investigated. The results showed that all the rubber/HNTs nanocomposites achieved strong interfacial interaction via interfacial covalent bonds, hydrogen bonds or multiple interactions, realized significantly improved dispersion of HNTs at nanoscale and exhibited excellent mechanical performances and other properties.

Effect of high-energy radiation on the rheological characteristics and structure of liquid rubbers

International Nuclear Information System (INIS)

Govorkov, A.T.; Zaitseva, V.I.; Muryshkin, D.L.; Safonov, Yu.N.

1987-01-01

The effect of high-energy radiation (γ-radiation and accelerated electrons) on liquid polybutadiene and polyisoprene rubbers (SKD, SKD-KTR, SKN) and butyl rubber (BR) was studied by IR and EPR spectroscopy, rheoviscosimetry, and chemical analysis. Newtonian flow was conserved in the rubbers under irradiation. The activation energy of viscous flow was unchanged, evidence of an increase in the contour length of the macromolecules without significant branching and cross-linking at the initial stages of the irradiation. A quantitative relationship was established between the rubber's dynamic viscosity and the absorbed dose, and features of the structure-formation mechanism in the liquid rubbers were determined

Correlation between nanostructural and electrical properties of barium titanate-based glass-ceramic nano-composites

Energy Technology Data Exchange (ETDEWEB)

Al-Assiri, M.S., E-mail: msassiri@kku.edu.sa [Department of Physics, King Khaled University, P.O. Box 9003, Abha (Saudi Arabia); El-Desoky, M.M., E-mail: mmdesoky@gmail.com [Department of Physics, King Khaled University, P.O. Box 9003, Abha (Saudi Arabia); Department of Physics, Faculty of Science, Suez Canal University, Suez (Egypt)

2011-09-08

Highlights: > Glasses have been transformed into nanomaterials by annealing at crystallization temperature. > Glass-ceramic nano-composites are important because of their new physical. > Grain sizes are the most significant structural parameter in electronic nanocrystalline phases. > These phases are very high electrical conductivity. > Hence, glass-ceramic nanocrystals are expected to be used, as gas sensors. - Abstract: Glasses in the system BaTiO{sub 3}-V{sub 2}O{sub 5}-Bi{sub 2}O{sub 3} have been transformed into glass-ceramic nano-composites by annealing at crystallization temperature T{sub cr} determined from DSC thermograms. After annealing they consist of small crystallites embedded in glassy matrix. The crystallization temperature T{sub cr} increases with increasing BaTiO{sub 3} content. XRD and TEM of the glass-ceramic nano-composites show that nanocrystals were embedded in the glassy matrix with an average grain size of 25 nm. The resulting materials exhibit much higher electrical conductivity than the initial glasses. It was postulated that the major role in the conductivity enhancement of these nanomaterials is played by the developed interfacial regions between crystalline and amorphous phases, in which the concentration of V{sup 4+}-V{sup 5+} pairs responsible for electron hopping, has higher than values that inside the glassy matrix. The experimental results were discussed in terms of a model proposed in this work and based on a 'core-shell' concept. From the best fits, reasonable values of various small polaron hopping (SPH) parameters were obtained. The conduction was attributed to non-adiabatic hopping of small polaron.

Nano ZnO/amine composites antimicrobial additives to acrylic paints

Directory of Open Access Journals (Sweden)

H.B. Kamal

2015-12-01

Full Text Available Nano ZnO has been widely used as an antimicrobial agent not only for food packaging purposes but also in many coating processes. The present work is meant to enhance such functions through the preparation of sustainable and safe conduct of nano ZnO composites with amine derivatives that are characterized by their antimicrobial and anti-fouling functional activities. The results obtained revealed a more comprehensive approach to the antimicrobial function based on the reported active oxide species role. The oxide/amine composites and the acrylic emulsion paint were characterized chemically and structurally through FT-IR, TGA and TEM supported by biological assessment of each ZnO/amine composite action. Results of the study concluded that equilibrium between the nano ZnO particles size, their dispersion form, and amine ability to stabilize the actively produced oxygen species responsible for the antimicrobial function, should all be accounted for when persistence of antimicrobial agent efficiency is regarded.

Cu–Co–O nano-catalysts as a burn rate modifier for composite solid propellants

Directory of Open Access Journals (Sweden)

D. Chaitanya Kumar Rao

2016-08-01

Full Text Available Nano-catalysts containing copper–cobalt oxides (Cu–Co–O have been synthesized by the citric acid (CA complexing method. Copper (II nitrate and Cobalt (II nitrate were employed in different molar ratios as the starting reactants to prepare three types of nano-catalysts. Well crystalline nano-catalysts were produced after a period of 3 hours by the calcination of CA–Cu–Co–O precursors at 550 °C. The phase morphologies and crystal composition of synthesized nano-catalysts were examined using Scanning Electron Microscope (SEM, Energy Dispersive Spectroscopy (EDS and Fourier Transform Infrared Spectroscopy (FTIR methods. The particle size of nano-catalysts was observed in the range of 90 nm–200 nm. The prepared nano-catalysts were used to formulate propellant samples of various compositions which showed high reactivity toward the combustion of HTPB/AP-based composite solid propellants. The catalytic effects on the decomposition of propellant samples were found to be significant at higher temperatures. The combustion characteristics of composite solid propellants were significantly improved by the incorporation of nano-catalysts. Out of the three catalysts studied in the present work, CuCo-I was found to be the better catalyst in regard to thermal decomposition and burning nature of composite solid propellants. The improved performance of composite solid propellant can be attributed to the high crystallinity, low agglomeration and lowering the decomposition temperature of oxidizer by the addition of CuCo-I nano-catalyst.

Effect of TiO, nanoparticles on the interface in the PET-rubber composites.

Science.gov (United States)

Vladuta, Cristina; Andronic, Luminita; Duta, Anca

2010-04-01

Usually, ceramic powders (SiO2, ZnO) are used as fillers for enhancing rubber mechanical strength. Poly-ethylene terephthalate (PET)-rubber nanocomposites were prepared by compression molding using titanium oxide (TiO2) nanoparticles as low content fillers (rubber nanocomposites were studied before and after keeping the samples under UV-radiation for a week. UV-radiation has interesting potential for the photochemical modification of polymers and TiO2. The influence of UV radiation on the properties of the interface polymer-TiO2 nanoparticles was evaluated. The impact of nanoparticle aggregates on the nanometer to micrometer organization of PET-rubber composites was studied with Atomic Force Microscopy (AFM). The interface properties were explained by measuring the contact angles and surface tensions. The interactions between components of nanocomposites were investigated with Fourier Transform-Infrared (FTIR) and the effects of TiO2 nanoparticle on the interfaces and composites crystalline structure were evaluated by X-ray diffraction (XRD). The results proved that the TiO2 nanoparticles, in different weight percentages, did not alter the nanocomposites crystallinity or the average crystallites size, but improve the interface properties.

Lignocellulosic fiber reinforced rubber composites

CSIR Research Space (South Africa)

Jacob John, Maya

2009-04-01

Full Text Available Natural Rubber (NR) is a naturally occurring elastomeric polymer of isoprene (2-methyl-1,3-butadiene). It can be extracted from latex of only one kind of tree, the Hevea braziliensis. Hevea rubber is produced in many tropical regions of Southeast...

Infrared Spectroscopic Study on Structural Change and Interfacial Interaction in Rubber Composites Filled with Silica-Kaolin Hybrid Fillers

Science.gov (United States)

Chen, Y.; Guan, J.; Hu, H.; Gao, H.; Zhang, L.

2016-07-01

A series of natural rubber/styrene butadiene rubber/polybutadiene rubber composites was prepared with nanometer silica and micron kaolin by a dry modification process, mechanical compounding, and mold vulcanization. Fourier transform infrared spectroscopy and a scanning electron microscope were used to investigate the structural changes and interfacial interactions in composites. The results showed that the "seesaw" structure was formed particularly with the incorporation of silica particles in the preparation process, which would be beneficial to the dispersibility of fillers in the rubber matrix. The kaolinite platelets were generally arranged in directional alignment. Kaolinite with smaller particle size and low-defect structure was more stable in preparation, but kaolinite with larger particle size and high defect structure tended to change the crystal structure. The composite prepared in this research exhibited excellent mechanical and thermal properties.

Effects of strain rate and temperature on the mechanical behavior of carbon black reinforced elastomers based on butyl rubber and high molecular weight polyethylene

Science.gov (United States)

Hussein, M.

2018-06-01

The influence of the mechanical property and morphology of different blend ratio of Butyl rubber (IIR)/high molecular weight polyethylene (PE) by temperature and strain rate are performed. Special attention has been considered to a ductile-brittle transition that is known to occur at around 60 °C. The idea is to explain the unexpected phenomenon of brittleness which directly related to all tensile mechanical properties such as the strength of blends, modulus of elasticity of filled and unfilled IIR-polyethylene blends. In particular, the initial Young's modulus, tensile strength and strain at failure exhibit similar dependency on strain rate and temperature. These quantities lowered and increased with an increment of temperature, whereas the increased with increasing of strain rate. Furthermore, the tensile strength and strain at failure decreases for all temperatures range with the increase of PE content in the blend, except Young's modulus in reverse. The strain rate sensitivity index parameter of the examined polymeric materials is consistent with the micro-mechanisms of deformation and the behavior was well described by an Eyring relationship leading to an activation volume of ∼1 nm3, except for the highest value of unfilled IIR ∼8.45 nm3.

Neutron shielding behavior of thermoplastic natural rubber/boron carbide composites

Science.gov (United States)

Mat Zali, Nurazila; Yazid, Hafizal; Megat Ahmad, Megat Harun Al Rashid

2018-01-01

Many shielding materials have been designed against the harm of different types of radiation to the human body. Today, polymer-based lightweight composites have been chosen by the radiation protection industry. In the present study, thermoplastic natural rubber (TPNR) composites with different weight percent of boron carbide (B4C) fillers (0% to 30%) were fabricated as neutron shielding through melt blending method. Neutron attenuation properties of TPNR/B4C composites have been investigated. The macroscopic cross section (Σ), half value layer (HVL) and mean free path length (λ) of the composites have been calculated and the transmission curves have been plotted. The obtained results show that Σ, HVL and λ greatly depend on the B4C content. Addition of B4C fillers into TPNR matrix were found to enhance the macroscopic cross section values thus decrease the mean free path length (λ) and half value layer (HVL) of the composites. The transmission curves exhibited that the neutron transmission of the composites decreased with increasing shielding thickness. These results showed that TPNR/B4C composites have high potential for neutron shielding applications.

Natural Rosin-based Phosphate Diester Surfactant Assisted One-step Synthesis of 3D Flowerlikeβ-Ni(OH)2/γ-Ni(OH)2 Composite Nano-microspheres

Institute of Scientific and Technical Information of China (English)

BoShi Wu; Juan Li; ChunRui Han; Feng Xu

2018-01-01

Self-assembled uniform 3Dflowerlikeβ-Ni(OH)2/g-Ni(OH)2composite nano-microspheres with hollow interiors were successfully synthesized via a facile aqueous-ethanol mixed solvothermal method, using nickel sulfate as a precursor, urea as a precipitant, and dehydroabietic based phosphate diester sodium (DDPDS) as a surfactant. The prepared 3D flowerlikeβ-Ni(OH)2/g-Ni(OH)2composite nano-microspheres were tested as supercapacitors in a two-electrode cell with 6 mol/L KOH electrolyte. In addition, the influence of DDPDS concentration on the morphology and size of 3Dflowerlikeβ-Ni(OH)2/g-Ni(OH)2composite nano-microspheres was studied at 180℃. X-ray diffraction (XRD), scanning electron microscopy (SEM), BET(Brunauer, Emmett and Teller)techniques, and equity default swap (EDS) were used to characterize the structure, morphology, and size of the as-prepared samples. Moreover, a possible formation mechanism of the 3Dflowerlikeβ-Ni(OH)2/g-Ni(OH)2composite nano-microspheres was proposed based on the effects of DDPDS concentrationand reaction time. The surfactant micelles were used as soft templates to induce the self-assembly of nanosheets. The crystallinity of the 3D flowerlikeβ-Ni(OH)2/g-Ni(OH)2composite nano-microspheres improved with the increase of DDPDS concentration, and the morphology and size of synthetic nano-microspheres could be controlled.

Interfacial interaction between the epoxidized natural rubber and silica in natural rubber/silica composites

Energy Technology Data Exchange (ETDEWEB)

Xu, Tiwen [College of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Jia, Zhixin, E-mail: zxjia@scut.edu.cn [College of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Luo, Yuanfang; Jia, Demin [College of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Peng, Zheng [Agricultural Product Processing Research Institute, Chinese Academy of Tropical Agriculture Sciences, Zhanjiang 524001 (China)

2015-02-15

Highlights: • Substantiate the ring open reaction between Si-OH of silica and epoxy groups of ENR. • ENR can act as a bridge between NR and silica to enhance the interfacial interaction. • As a modifier, ENR gets the potential to be used in the tread of green tire for improving the wet skid resistance apparently. - Abstract: The epoxidized natural rubber (ENR) as an interfacial modifier was used to improve the mechanical and dynamical mechanical properties of NR/silica composites. In order to reveal the interaction mechanism between ENR and silica, the ENR/Silica model compound was prepared by using an open mill and the interfacial interaction of ENR with silica was investigated by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), X-ray diffraction (XRD) and stress–strain testing. The results indicated that the ring-opening reaction occurs between the epoxy groups of ENR chains and Si-OH groups on the silica surfaces and the covalent bonds are formed between two phases, which can improve the dispersion of silica in the rubber matrix and enhance the interfacial combination between rubber and silica. The ring-opening reaction occurs not only in vulcanization process but also in mixing process, meanwhile, the latter seems to be more important due to the simultaneous effects of mechanical force and temperature.

Self-Healing Natural Rubber with Tailorable Mechanical Properties Based on Ionic Supramolecular Hybrid Network.

Science.gov (United States)

Xu, Chuanhui; Cao, Liming; Huang, Xunhui; Chen, Yukun; Lin, Baofeng; Fu, Lihua

2017-08-30

In most cases, the strength of self-healing supramolecular rubber based on noncovalent bonds is in the order of KPa, which is a challenge for their further applications. Incorporation of conventional fillers can effectively enhance the strength of rubbers, but usually accompanied by a sacrifice of self-healing capability due to that the filler system is independent of the reversible supramolecular network. In the present work, in situ reaction of methacrylic acid (MAA) and excess zinc oxide (ZnO) was realized in natural rubber (NR). Ionic cross-links in NR matrix were obtained by limiting the covalent cross-linking of NR molecules and allowing the in situ polymerization of MAA/ZnO. Because of the natural affinity between Zn 2+ ion-rich domains and ZnO, the residual nano ZnO participated in formation of a reversible ionic supramolecular hybrid network, thus having little obstructions on the reconstruction of ionic cross-links. Meanwhile, the well dispersed residual ZnO could tailor the mechanical properties of NR by changing the MAA/ZnO molar ratios. The present study thus provides a simple method to fabricate a new self-healing NR with tailorable mechanical properties that may have more potential applications.

Mechanical, thermal and friction properties of rice bran carbon/nitrile rubber composites: Influence of particle size and loading

International Nuclear Information System (INIS)

Li, Mei-Chun; Zhang, Yinhang; Cho, Ur Ryong

2014-01-01

Highlights: • A novel rice bran carbon (RBC) is used to reinforce nitrile rubber. • We study the effect of RBC particle size on the performances of nitrile rubber. • We study the effect of RBC loading on the performances of nitrile rubber. • The addition of RBC improves the mechanical properties of nitrile rubber. • The addition of RBC improves the anti-skid properties of nitrile rubber. - Abstract: Four types of rice bran carbon (RBC) with different particle sizes were compounded with nitrile rubber (NBR) in a laboratory size two-roll miller. The obtained RBC/NBR composites were characterized using Field Emission Scanning Electron Microscopy (FE-SEM) and tensile tests. Experimental results showed the RBC with lowest particle size exhibited best dispersion state and superior reinforcement ability. Then, we investigated the influence of RBC loading on the morphology, vulcanization characteristics, mechanical, thermal and friction properties of NBR composites. Experimental results indicated that the incorporation of RBC resulted in higher torque values, longer curing time, but shorter scorch time. The addition of RBC remarkably improved the mechanical properties of NBR composites. However, when the RBC loading exceeded 60 phr, the improvement in the tensile strength was not significant due to the poor dispersion state and weak interfacial bonding between RBC and NBR matrix, which were confirmed by Mooney–Rivlin stress–strain curves and FE-SEM observations. The thermal stabilities of RBC/NBR composites were largely improved as the loading of RBC increased. Friction tests revealed that under a certain concentration, the presence of RBC increased the static friction coefficient of NBR composites, suggesting the anti-skid role of RBC in the NBR composites. The overall results demonstrated that RBC could act as ideal filler for NBR composites providing both economic and environmental advantages

Eco-nano composite films containing copper as potential antimicrobial active packaging

Energy Technology Data Exchange (ETDEWEB)

Bruna, Julio E.; Gonzalez, Valeska; Rodriguez, Francisco; Guarda, Abel; Galotto, Maria Jose, E-mail: julio.bruna@usach.cl [Center for the Development of Nanoscience and Nanotechnology, Packaging Laboratory, University of Santiago de Chile. Santiago (Chile)

2011-07-01

The antimicrobial efficiency of Cellulose Acetate/MMTCu and Chitosan/MMTCu nano composites against Escherichia Coli 0157:H7 n/t has been studied in the present work. The MMT modified with copper were obtained using cation interchange in solution and the nano composites films were prepared using casting solution technique, being the biodegradable polymer (Cellulose Acetate or Chitosan) the main component and the montmorillonite modified with copper, the minority component. Characterization of MMTCu and the nano composites (CA/MMTCu and Ch/MMTCu), were carried out using XRD, AA, TGA, DSC and microbiological analysis. The nano composites showed to be more stable at higher temperature, resulting from the incorporation of MMTCu into the polymer. On the other hand, the results indicated that the antibacterial effect of nano composite increased with the proportion of MMTCu added. (author)

Eco-nano composite films containing copper as potential antimicrobial active packaging

International Nuclear Information System (INIS)

Bruna, Julio E.; Gonzalez, Valeska; Rodriguez, Francisco; Guarda, Abel; Galotto, Maria Jose

2011-01-01

The antimicrobial efficiency of Cellulose Acetate/MMTCu and Chitosan/MMTCu nano composites against Escherichia Coli 0157:H7 n/t has been studied in the present work. The MMT modified with copper were obtained using cation interchange in solution and the nano composites films were prepared using casting solution technique, being the biodegradable polymer (Cellulose Acetate or Chitosan) the main component and the montmorillonite modified with copper, the minority component. Characterization of MMTCu and the nano composites (CA/MMTCu and Ch/MMTCu), were carried out using XRD, AA, TGA, DSC and microbiological analysis. The nano composites showed to be more stable at higher temperature, resulting from the incorporation of MMTCu into the polymer. On the other hand, the results indicated that the antibacterial effect of nano composite increased with the proportion of MMTCu added. (author)

Differential scanning calorimetric study of HTPB based composite propellants in presence of nano ferric oxide

Energy Technology Data Exchange (ETDEWEB)

Patil, Prajakta R.; Krishnamurthy, V.N.; Joshi, Satyawati S. [Department of Chemistry, University of Pune, Pune 411007 (India)

2006-12-15

A comparative study of the thermal decomposition of ammonium perchlorate (AP)/hydroxy terminated polybutadiene (HTPB) based composite propellants has been carried out in presence and absence of nano iron oxide at different heating rates in a dynamic nitrogen atmosphere using differential scanning calorimetry. The pronounced effect was a lowering of the high temperature decomposition by 49 C. A higher heat release up to 40% was observed in presence of nano ferric oxide (3.5 nm). The kinetic parameters were evaluated using the Kissinger method. The increase of the rate constant in the catalyzed propellant confirmed the enhancement of the catalytic activity of ammonium perchlorate. The scanning electron micrographs of nano Fe{sub 2}O{sub 3} incorporated in HTPB revealed a well-separated characteristic necklace-like structure of {alpha}-Fe{sub 2}O{sub 3} particles at high magnification. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Study on Carbon Nano composite Counter electrode for Dye-Sensitized Solar Cells

International Nuclear Information System (INIS)

Chen, Y.; Zhang, H.; Lin, J.

2012-01-01

Carbon nano composite electrodes were prepared by adding carbon nano tubes (CNTs) into carbon black as counter electrodes of dye-sensitized solar cells (DSSCs). The morphology and structure of carbon nano composite electrodes were studied by scanning electron microscopy. The influence of CNTs on the electrochemical performance of carbon nano composite electrodes is investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Carbon nano composite electrodes with CNTs exhibit a highly interconnected network structure with high electrical conductivity and good catalytic activity. The influence of different CNTs content in carbon nano composite electrodes on the open-circuit voltage, short-circuit current, and filling factor of DSSCs is also investigated. DSSCs with 10% CNTs content exhibit the best photovoltaic performance in our experiments.

Carboxymethyl Cellulose From Kenaf Reinforced Composite Polymer Electrolytes Based 49 % Poly (Methyl Methacrylate)-Grafted Natural Rubber

International Nuclear Information System (INIS)

Serawati Jafirin; Ishak Ahmad; Azizan Ahmad; Ishak Ahmad; Azizan Ahmad

2014-01-01

Composite polymer electrolytes based 49 % poly(methyl methacrylate)-grafted natural rubber (MG49) incorporating lithium triflate (LiCF 3 SO 3 ) were prepared. The study mainly focuses on the ionic conductivity performances and mechanical properties. Prior to that, carboxymethyl cellulose was synthesized from kenaf fiber. The films were characterized by electrochemical impedance (EIS) spectroscopy, linear sweep voltammetry (LSV), universal testing machine and scanning electron microscopy (SEM). The conductivity was found to increase with carboxymethyl cellulose loading. The highest conductivity value achieved was 6.5 x 10 -6 Scm -1 upon addition of 6 wt % carboxymethyl cellulose. LSV graph shows the stability of this film was extended to 2.7 V at room temperature. The composition with 6 wt % carboxymethyl cellulose composition showed the highest tensile strength value of 7.9 MPa and 273 MPa of Young's modulus. The morphology of the electrolytes showed a smooth surface of films after addition of salt and filler indicating amorphous phase in electrolytes system. Excellent mechanical properties and good ionic conductivity are obtained, enlightening that the film is suitable for future applications as thin solid polymer electrolytes in lithium batteries. (author)

Carboxylated nitrile butadiene rubber/hybrid filler composites

Directory of Open Access Journals (Sweden)

Ahmad Mousa

2012-08-01

Full Text Available The surface properties of the OSW and NLS are measured with the dynamic contact-angle technique. The x-ray photoelectron spectroscopy (XPS of the OSW reveals that the OSW possesses various reactive functional groups namely hydroxyl groups (OH. Hybrid filler from NLS and OSW were incorporated into carboxylated nitrile rubber (XNBR to produce XNBR hybrid composites. The reaction of OH groups from the OSW with COOH of the XNBR is checked by attenuated total reflectance spectra (ATR-IR of the composites. The degree of curing ΔM (maximum torque-minimum torque as a function of hybrid filler as derived from moving die rheometer (MDR is reported. The stress-strain behavior of the hybrid composites as well as the dynamic mechanical thermal analysis (DMTA is studied. Bonding quality and dispersion of the hybrid filler with and in XNBR are examined using scanning-transmission electron microscopy (STEM in SEM.

Clinical and radiographic evaluation of citric acid-based nano hydroxyapatite composite graft in the regeneration of intrabony defects - A randomized controlled trial

Directory of Open Access Journals (Sweden)

Chaurasia Priya Dayashankar

2017-01-01

Full Text Available Background: Conventional periodontal therapy with various bone grafts has limited scope and the results are not predictable. To improve their utility, the hybridization of bioceramics and biodegradable polymers has been widely adopted to reform the mechanical properties of bone grafts. One such biodegradable polymer is POC (Poly 1,8 octanediol. Secondly, citric acid is considered as the key material in bone mineralization, which is related to the overall stability, strength and fracture resistance of bone. Hence citric acid is incorporated in a polymer and Nano hydroxyapatite to form a composite graft, for periodontal bone regeneration. This study attempts to evaluate the efficacy of citric acid based Nano-hydroxyapatite composite graft for the treatment of intrabony defects in chronic periodontitis patients over 12 months. Methods: A split mouth study, which consists of 10 systemically healthy patients, were randomly treated with Citric acid based Nano hydroxyapatite composite graft (test sites, n=18 or with Nano hydroxyapatite alone (control sites, n=15. Plaque index, gingival index, gingival bleeding index, probing pocket depth (PPD, clinical attachment level (CAL, bone probing depth (BPD and hard tissue parameters such as amount of defect fill, percentage of defect fill, and changes in alveolar crest were assessed over a period of 12 months. Statistical analysis used was student's t-test and One-Way ANOVA. Results: Both test and control sites demonstrated statistically significant reduction of PD, BPD, gain in CAL and radiographic bone fill. Nevertheless the test sites showed Statistically significant improvements in all the parameters as compared to control sites at 12 months. Conclusion: Citric acid based Nano hydroxyapatite composite graft can be considered as a newer material for periodontal regeneration.

[Study on spectroscopic characterization and property of PES/ micro-nano cellulose composite membrane material].

Science.gov (United States)

Tang, Huan-Wei; Zhang, Li-Ping; Li, Shuai; Zhao, Guang-Jie; Qin, Zhu; Sun, Su-Qin

2010-03-01

In the present paper, the functional groups of PES/micro-nano cellulose composite membrane materials were characterized by Fourier transform infrared spectroscopy (FTIR). Also, changes in crystallinity in composite membrane materials were analyzed using X-ray diffraction (XRD). The effects of micro-nano cellulose content on hydrophilic property of composite membrane material were studied by measuring hydrophilic angle. The images of support layer structure of pure PES membrane material and composite membrane material were showed with scanning electron microscope (SEM). These results indicated that in the infrared spectrogram, the composite membrane material had characteristic peaks of both PES and micro-nano cellulose without appearance of other new characteristics peaks. It revealed that there were no new functional groups in the composite membrane material, and the level of molecular compatibility was achieved, which was based on the existence of inter-molecular hydrogen bond association between PES and micro-nano cellulose. Due to the existence of micro-nano cellulose, the crystallinity of composite membrane material was increased from 37.7% to 47.9%. The more the increase in micro-nano cellulose mass fraction, the better the van de Waal force and hydrogen bond force between composite membrane material and water were enhanced. The hydrophilic angle of composite membrane material was decreased from 55.8 degrees to 45.8 degrees and the surface energy was raised from 113.7 to 123.5 mN x m(-2). Consequently, the hydrophilic property of composite membrane material was improved. The number of pores in the support layer of composite membrane material was lager than that of pure PES membrane. Apparently, pores were more uniformly distributed.

Properties of tire rubber with zinc-containing technological additives

Directory of Open Access Journals (Sweden)

S. N. Kayushnikov

2017-01-01

Full Text Available In this paper, we studied the influence of zinc-containing technological additives on partial replacement of zinc oxide and stearic acid on deformation-strength and performance properties of tire elastomeric compositions based on polyisoprene rubber and combination of oil-filled butadiene-styrene and polybutadiene rubbers. It was revealed that partial replacement of zinc oxide and stearic acid with zinc-containing technological additives does not significantly affect the basic physico-mechanical properties of rubbers based on synthetic rubbers of general use. It was determined that the introduction of zinc-containing technological additives SCC2 in combination with zinc oxide in all the studied ratios and SCC3 in combination with zinc oxide in 4: 1 and 3: 1 ratios leads to increase (up to 10.4% of the resistance of these rubbers under the action of temperature-force fields, which is probably due to a more even distribution of polar components of curing system in non-polar elastomeric matrix, as well as the type of cross-links formed during vulcanization under the action of surface-active additives. It has been found that the introduction of zinc-containing additives into the elastomeric compositions based on SRMS-30 ARKM-15 + SRD in combination with zinc oxide leads to increase to 6.3% of wear resistance of rubbers, which may be due to a lower defectiveness of vulcanization structure of these rubbers, concentration of stress centers in the material. For rubbers based on SRI-3, preservation of bond strength of rubber with a textile cord at a sufficiently high level is shown.

Poly (lactic acid organoclay nano composites for paper coating applications

Directory of Open Access Journals (Sweden)

Tatcha Sonjui

2014-10-01

Full Text Available Poly(lactic acid or PLA is a well-known biodegradable polymer derived from renewable resources such as corn strach, tapioca strach, and sugar cane. PLA is the most extensively utilized biodegradable polyester with potential to replace conventional petrochemical-based polymers. However, PLA has some drawbacks, such as brittleness and poor gas barrier properties. Nano composite polymers have experience and increasing interest due to their characteristics, especially in mechanical and thermal properties. The objectives of this research were to prepare PLA formulations using three different PLAs. The formulas giving high gloss coating film were selected to prepare nano composite film by incorporated with different amount of various types of organoclays. The physical properties of the PLA coating films were studied and it was found that the PLA 7000D with 0.1%w/w of Cloisite 30B provided decent viscosity for coating process. In addition, the nano composite coating films showed good physical properties such as high gloss, good adhesion, and good hardness. There is a possibility of using the obtained formulation as a paper coating film.

Mechanical and Morphological Properties of Short Nylon Fiber Reinforced Acrylonitrile-Butadiene Rubber Composites

Directory of Open Access Journals (Sweden)

S.H. Mohseniyan

2010-12-01

Full Text Available Acrylonitrile butadiene rubber (NBR composites are prepared from waste nylon 66 short fiber using a two-roll mill mixer. The effects of fiber content and bonding agent on the mechanical and morphological properties of the composites are studied. The curing characteristics of the composites have been studied by using cure rheometer. The cure and scorch time of the composites decrease while cure rate is increased when short fiber content is increased. The mechanical properties of the composites show improvement in both longitudinal and transverse directions with increase in short fiber content. The adhesion between the fiber and rubber is enhanced by using a dry bonding system consisting of resorcinol, xamethylenetetramine and hydrated silica (HRH. The swelling behavior of the composites in N,N-dimethylformamide is tested to find the effect of bonding agent on adhesion strength of the matrix and fibers. Fracture surface morphology of composites is studied by scanning electron microscopy. The restriction to swelling is higher for composites containing bonding agent, especially, in the longitudinal direction. The morphology of the fracture surface shows less fiber pull out when the bonding agent is introduced.

Antimicrobial Properties of Chitosan-Alumina/f-MWCNT Nano composites

International Nuclear Information System (INIS)

Masheane, M.; Nthunya, L.; Malinga, S.; Masheane, M.; Nthunya, L.; Nxumalo, E.; Mhlanga, S.; Barnard, T.

2016-01-01

Antimicrobial chitosan-alumina/functionalized-multi walled carbon nano tube (f-MWCNT) nano composites were prepared by a simple phase inversion method. Scanning electron microscopy (SEM) analyses showed the change in the internal morphology of the composites and energy dispersive spectroscopy (EDS) confirmed the presence of alumina and f-MWCNTs in the chitosan polymer matrix. Fourier transform infrared (FTIR) spectroscopy showed the appearance of new functional groups from both alumina and f-MWCNTs, and thermogravimetric analysis (TGA) revealed that the addition of alumina and f-MWCNTs improved the thermal stability of the chitosan polymer. The presence of alumina and f-MWCNTs in the polymer matrix was found to improve the thermal stability and reduced the solubility of chitosan polymer. The prepared chitosan-alumina/f-MWCNT nano composites showed inhibition of twelve strains of bacterial strains that were tested. Thus, the nano composites show a potential for use as a biocides in water treatment for the removal of bacteria at different environmental conditions.

Mechanical and tribological properties of acrylonitrile–butadiene rubber filled with graphite and carbon black

International Nuclear Information System (INIS)

Wang, Lei Lei; Zhang, Li Qun; Tian, Ming

2012-01-01

Highlights: ► Graphite/carbon black/rubber micro- and nano-composites were prepared. ► Nanocomposites showed better mechanical properties and wear resistance. ► The effect of load and sliding speed on friction and wear is significant. ► Graphite lubricant film can reduce friction coefficient and wear rate. -- Abstract: In this work, acrylonitrile–butadiene rubber (NBR)/expanded graphite (EG)/carbon black (CB) micro- and nanocomposites were prepared by two different methods, and the resulting mechanical and tribological properties were compared with those of NBR/CB composites. Meanwhile, the effects of graphite dispersion and loading content, as well as the applied load and sliding velocity on the tribological behavior of the above composites under dry friction condition were also evaluated. The worn surfaces were analyzed by scanning electron microscopy (SEM) to disclose wear mechanism. As expected, the better the dispersion of graphite, the more remarkable enhancement on tensile and dynamic mechanical properties, and the greater reduction in the coefficient of friction (COF) and specific wear rate (W s ). It was found that a small amount of EG could effectively decrease COF and W s of NBR/CB composites because of the formation of graphite lubricant films. The COF and W s of NBR/CB/EG composites show a decreasing trend with a rise in applied load and sliding velocity. NBR/CB/EG nanocomposite always shows a stable wearing process with relatively low COF and W s . It is thought that well-dispersed graphite nano-sheets were beneficial to the formation of a fine and durable lubricant film.

Bonding performance of self-adhesive flowable composites to enamel, dentin and a nano-hybrid composite.

Science.gov (United States)

Peterson, Jana; Rizk, Marta; Hoch, Monika; Wiegand, Annette

2018-04-01

This study aimed to analyze bond strengths of self-adhesive flowable composites on enamel, dentin and nano-hybrid composite. Enamel, dentin and nano-hybrid composite (Venus Diamond, Heraeus Kulzer, Germany) specimens were prepared. Three self-adhesive composites (Constic, DMG, Germany; Fusio Liquid Dentin, Pentron Clinical, USA; Vertise Flow, Kerr Dental, Italy) or a conventional flowable composite (Venus Diamond Flow, Heraeus Kulzer, Germany, etch&rinse technique) were applied to enamel and dentin. Nano-hybrid composite specimens were initially aged by thermal cycling (5000 cycles, 5-55 °C). Surfaces were left untreated or pretreated by mechanical roughening, Al 2 O 3 air abrasion or silica coating/silanization. In half of the composite specimens, an adhesive (Optibond FL, Kerr Dental, Italy) was used prior to the application of the flowable composites. Following thermal cycling (5000 cycles, 5-55 °C) of all specimens, shear bond strengths (SBS) and failure modes were analyzed (each subgroup n = 16). Statistical analysis was performed by ANOVAs/Bonferroni post hoc tests, Weibull statistics and χ 2 -tests (p composites on enamel and dentin were significantly lower (enamel: composite (enamel: 13.0 ± 5.1, dentin: 11.2 ± 6.3), and merely adhesive failures could be observed. On the nano-hybrid composite, SBS were significantly related to the pretreatment. Adhesive application improved SBS of the conventional, but not of the self-adhesive composites. The self-adhesive composite groups showed less cohesive failures than the reference group; the occurence of cohesive failures increased after surface pretreatment. Bonding of self-adhesive flowable composites to enamel and dentin is lower than bonding to a nano-hybrid composite.

Neutron scattering analysis of rubber carbon black composite structure

International Nuclear Information System (INIS)

Hjelm, R.P. Jr.; Wampler, W.A.; Gerspacher, M.

1994-01-01

We explore the uses of small-angle neutron scattering to dissect component form, structure and distribution in carbon black-reinforced rubber by varying the contrast of the system relative to some fluid by changing the fluid scattering-length density. This is the method of contrast variation. Contrast variation allows us to separate scattering contributions from the different components. Here, we extend our studies on high surface area (HSA) carbon black suspended in cyclohexane/deuterocyclohexane to HSA mixed with polyisoprene as a gel of ''bound'' rubber swollen with the same solvent mixtures. Contrast variation of swollen composite gels shows that there are two length scales in the gel structure. Above 1 nm fluctuations in the carbon black predominate. Interactions with elastomer hold the HSA aggregates appart. Below 1 nm the scattering is largely from the elastomer. The smooth surface structure of the carbon black is unaltered by the interactions with elastomer and appears smooth over length scales above about 1 nm. These results show that contrast variation can provide information on composite structure that is not available by other means. This information relates to the reinforcement mechanism of elastomers by carbon blacks

Properties of natural rubber composites with structurally different clay intercalable surfactants

Czech Academy of Sciences Publication Activity Database

Sedničková, M.; Jochec-Mošková, D.; Janigová, I.; Kronek, J.; Jankovič, L.; Šlouf, Miroslav; Chodák, I.

2017-01-01

Roč. 24, č. 7 (2017), s. 1-13, č. článku 105. ISSN 1022-9760 Institutional support: RVO:61389013 Keywords : composite * natural rubber * clay Subject RIV: CD - Macromolecular Chemistry OBOR OECD: Polymer science Impact factor: 1.615, year: 2016

Magnetoimpedance of cobalt-based amorphous ribbons/polymer composites

Energy Technology Data Exchange (ETDEWEB)

Semirov, A.V., E-mail: semirov@mail.ru [Irkutsk State University, Irkutsk (Russian Federation); Derevyanko, M.S.; Bukreev, D.A.; Moiseev, A.A.; Kudryavtsev, V.O. [Irkutsk State University, Irkutsk (Russian Federation); Safronov, A.P. [Ural Federal University, Yekaterinburg (Russian Federation)

2016-10-01

The combined influence of the temperature, the elastic tensile stress and the external magnetic field on the total impedance and impedance components were studied for rapidly quenched amorphous Co{sub 75}Fe{sub 5}Si{sub 4}B{sub 16} ribbons. Both as-cast amorphous ribbons and Co{sub 75}Fe{sub 5}Si{sub 4}B{sub 16}/polymer amorphous ribbon based composites were considered. Following polymer coverings were studied: modified rubber solution in o-xylene, solution of butyl methacrylate and methacrylic acid copolymer in isopropanol and solution of polymethylphenylsiloxane resin in toluene. All selected composites showed very good adhesion of the coverings and allowed to provide temperature measurements from 163 K up to 383 K under the applied deforming tensile force up to 30 N. The dependence of the modulus of the impedance and its components on the external magnetic field was influenced by the elastic tensile stresses and was affected by the temperature of the samples. It was shown that maximal sensitivity of the impedance and its components to the external magnetic field was observed at minimal temperature and maximal deforming force depended on the frequency of an alternating current. - Highlights: • Impedance and its components of amorphous Co{sub 75}Fe{sub 5}Si{sub 4}B{sub 16} ribbons were studied. • MI sensitivity to the magnetic field depends on a temperature and a deforming force. • Polymer covering can affect the functional properties of the composite.

Strain distributions in nano-onions with uniform and non-uniform compositions

International Nuclear Information System (INIS)

Duan, H L; Karihaloo, B L; Wang, J; Yi, X

2006-01-01

Nano-onions are ellipsoidal or spherical particles consisting of a core surrounded by concentric shells of nanometre size. Nano-onions produced by self-assembly and colloidal techniques have different structures and compositions, and thus differ in the state of strains. The mismatch of the thermal expansion coefficients and lattice constants between neighbouring shells induces stress/strain fields in the core and shells, which in turn affect their physical/mechanical properties and/or the properties of the composites containing them. In this paper, the strains in embedded and free-standing nano-onions with uniform and non-uniform compositions are studied in detail. It is found that the strains in the nano-onions can be modified by adjusting their compositions and structures. The results are useful for the band structure engineering of semiconductor nano-onions

Fabrication of Surface Level Cu/Si Cp Nano composites by Friction Stir Processing Route

International Nuclear Information System (INIS)

Srinivasan, R. C.; Karunanithi, M.

2015-01-01

Friction stir processing (FSP) technique has been successfully employed as low energy consumption route to prepare copper based surface level nano composites reinforced with nano sized silicon carbide particles (Si Cp). The effect of FSP parameters such as tool rotational speed, processing speed, and tool tilt angle on microstructure and microhardness was investigated. Single pass FSP was performed based on Box-Behnken design at three factors in three levels. A cluster of blind holes 2 mm in diameter and 3 mm in depth was used as particulate deposition technique in order to reduce the agglomeration problem during composite fabrication. K-type thermocouples were used to measure temperature histories during FSP. The results suggest that the heat generation during FSP plays a significant role in deciding the microstructure and microhardness of the surface composites. Microstructural observations revealed a uniform dispersion of nano sized Si Cp without any agglomeration problem and well bonded with copper matrix at different process parameter combinations. X-ray diffraction study shows that no intermetallic compound was produced after processing. The microhardness of nano composites was remarkably enhanced and about 95% more than that of copper matrix

Progress in Tribological Properties of Nano-Composite Hard Coatings under Water Lubrication

Directory of Open Access Journals (Sweden)

Qianzhi Wang

2017-02-01

Full Text Available The tribological properties, under water-lubricated conditions, of three major nano-composite coatings, i.e., diamond-like carbon (DLC or a-C, amorphous carbon nitride (a-CNx and transition metallic nitride-based (TiN-based, CrN-based, coatings are reviewed. The influences of microstructure (composition and architecture and test conditions (counterparts and friction parameters on their friction and wear behavior under water lubrication are systematically elucidated. In general, DLC and a-CNx coatings exhibit superior tribological performance under water lubrication due to the formation of the hydrophilic group and the lubricating layer with low shear strength, respectively. In contrast, TiN-based and CrN-based coatings present relatively poor tribological performance in pure water, but are expected to present promising applications in sea water because of their good corrosion resistance. No matter what kind of coatings, an appropriate selection of counterpart materials would make their water-lubricated tribological properties more prominent. Currently, Si-based materials are deemed as beneficial counterparts under water lubrication due to the formation of silica gel originating from the hydration of Si. In the meantime, the tribological properties of nano-composite coatings in water could be enhanced at appropriate normal load and sliding velocity due to mixed or hydrodynamic lubrication. At the end of this article, the main research that is now being developed concerning the development of nano-composite coatings under water lubrication is described synthetically.

Inducing PLA/starch compatibility through butyl-etherification of waxy and high amylose starch.

Science.gov (United States)

Wokadala, Obiro Cuthbert; Emmambux, Naushad Mohammad; Ray, Suprakas Sinha

2014-11-04

In this study, waxy and high amylose starches were modified through butyl-etherification to facilitate compatibility with polylactide (PLA). Fourier transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy and wettability tests showed that hydrophobic butyl-etherified waxy and high amylose starches were obtained with degree of substitution values of 2.0 and 2.1, respectively. Differential scanning calorimetry, tensile testing, and scanning electron microscopy (SEM) demonstrated improved PLA/starch compatibility for both waxy and high amylose starch after butyl-etherification. The PLA/butyl-etherified waxy and high amylose starch composite films had higher tensile strength and elongation at break compared to PLA/non-butyl-etherified composite films. The morphological study using SEM showed that PLA/butyl-etherified waxy starch composites had a more homogenous microstructure compared to PLA/butyl-etherified high amylose starch composites. Thermogravimetric analysis showed that PLA/starch composite thermal stability decreased with starch butyl-etherification for both waxy and high amylose starches. This study mainly demonstrates that PLA/starch compatibility can be improved through starch butyl-etherification. Copyright © 2014 Elsevier Ltd. All rights reserved.

Shock compression parameters for a boron-loaded, silicone-rubber composite

International Nuclear Information System (INIS)

Gust, W.H.; Van Thiel, M.; Gathers, G.R.

1975-01-01

Hugoniot parameters under uniaxial-shock-wave-loading from 0.03 to 0.6 Mbar are presented for a composite with 70 wt percent boron loaded in a silicone-rubber matrix. The plot of shock velocity vs particle velocity was found to be nonlinear. Equations that describe fits of the data are presented. (U.S.)

Influence of fillers on hydrogen penetration properties and blister fracture of rubber composites for O-ring exposed to high-pressure hydrogen gas

Energy Technology Data Exchange (ETDEWEB)

Yamabe, Junichiro; Nishimura, Shin [Department of Mechanical Science Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395 (Japan); Research Center for Hydrogen Industrial Use and Storage (HYDROGENIUS), National Institute of Advanced Industrial Science and Technology (AIST), 744 Motooka, Nishi-ku, Fukuoka 819-0395 (Japan)

2009-02-15

Ethylene-propylene rubber (EPDM) and nitrile-butadiene rubber (NBR) composites having carbon black, silica, and no fillers were exposed to hydrogen gas at a maximum pressure of 10 MPa; then, blister tests and the measurement of hydrogen content were conducted. The hydrogen contents of the composites were proportional to the hydrogen pressure, i.e., the behavior of their hydrogen contents follows Henry's law. This implies that hydrogen penetrates into the composite as a hydrogen molecule. The addition of carbon black raised the hydrogen content of the composite, while the addition of silica did not. Based on observations, the blister damages of composites with silica were less pronounced, irrespective of the hydrogen pressures. This may be attributed to their lower hydrogen content and relatively better tensile properties than the others. (author)

The improvement in functional characteristics of eco-friendly composites made of natural rubber and cellulose

Energy Technology Data Exchange (ETDEWEB)

Araki, Kunihiro; Kaneko, Shonosuke; Matsumoto, Koki; Tanaka, Tatsuya; Arao, Yoshihiko [Applied Materials Engineering Laboratory, Faculty of Engineering, Doshisha University, 1-3, Tatara Miyakodani, Kyotanabe, Kyoto, 610-0321 (Japan); Nagatani, Asahiro [Applied Materials Engineering Laboratory, Faculty of Engineering, Doshisha University, 1-3, Tatara Miyakodani, Kyotanabe, Kyoto, 610-0321 (Japan); Hyogo Prefectural Institute of Technology, 3-1-12, Yukihira-cho, Suma-ku, Kobe, Hyogo, 654-0037 (Japan)

2015-05-22

We investigated the efficient use of cellulose to resolve the problem of the depletion of fossil resources. In this study, as the biomass material, the green composite based on natural rubber (NR) and the flake-shaped cellulose particles (FSCP) was produced. In order to further improvement of functional characteristics, epoxidized natural rubber (ENR) was also used instead of NR. The FSCP were produced by mechanical milling in a planetary ball mill with a grinding aid as a cellulose aggregation inhibitor. Moreover, talc and mica particles were used to compare with FSCP. NR and ENR was mixed with vulcanizing agents and then each filler was added to NR compound in an internal mixer. The vulcanizing agents are as follows: stearic acid, zinc oxide, sulfur, and vulcanization accelerator. The functionalities of the composites were evaluated by a vibration-damping experiment and a gas permeability experiment. As a result, we found that FSCP filler has effects similar to (or more than) inorganic filler in vibration-damping and O{sub 2} barrier properties. And then, vibration- damping and O{sub 2} barrier properties of the composite including FSCP was increased with use of ENR. In particular, we found that ENR-50 composite containing 50 phr FSCP has three times as high vibration-damping property as ENR-50 without FSCP.

Radiation Curing of Rubber/Thermoplastic Composites Containing Different Inorganic Fillers

International Nuclear Information System (INIS)

EL-Zayat, M.M.M.

2012-01-01

Blending of polymeric materials has proved to be a successful method for preparing new polymeric materials having not only the main properties of the blends components but also new modification as well as specific ones. High density polyethylene (HDPE) and acrylonitrile butadiene rubber (NBR) are both soild and constitute the blend components to be investigated in present study and hence the method of mechanical blending is the most suitable one for its preparation . HDPE thermoplastic is a semi – crystalline polymer ; on the other hand , NBR elastomer is totally amorphous polymer. Both polymers are categorized as crosslinking polymers with respect to ionizing gamma rays with different extents. In order to increase the efficiency of irradiation curing of such NBR/HDPE blend , it may be required to add suitable additives such as reinforcing fillers that may increase the extent of crosslinking at the same irradiation dose . Thus synthetic fillers are used commercially in industrial processing of rubber formulation due to its specific characteristics and hence its high reinforcing capacity and suitable price . To follow property changes occurred to the blend as well as its composites , measurements have been done to monitor the changes that happened to mechanical, physical and thermal properties as a function of irradiation dose and composition of blends and composites.

Development of rubberized geopolymer interlocking bricks

Directory of Open Access Journals (Sweden)

Bashar S Mohammed

2018-06-01

Full Text Available Waste tires contribute badly to the environment on a huge scale as they are bulky, non-biodegradable, and prone to fire and being a shelter for mosquitos and other insects. This paper reports on a novel approach towards the development of rubberized brick by utilizing crumb rubber as the sole fine aggregate in the production of geopolymer interlocking bricks. The response surface methodology (RSM from Design Experts software has been used to determine the numbers of trial mixes and their corresponding ingredients. A total of thirteen trial mixes were carried out and tested for compressive strength and the RSM model was developed to predict the design mix based on the targeted compressive strength. The mix design was obtained to be an 18 M for NaOH and 0.8 solution to fly ash ratio. The geopolymer interlocking rubberized bricks were then produced and tested for compressive strength, dimension, modulus of rupture, water absorption, initial rate of absorption, and efflorescence. The geopolymer interlocking rubberised bricks presented a low compressive and flexural strength and a high-water absorption capacity. The bricks were rated as non-effloresced and classified as 3rd class bricks which can be used as non-load bearing material. It is recommended to utilize nano silica in order to increase the strength of the brick. Keywords: Rubberized bricks, Crumb rubber, Interlocking bricks, Geopolymer, Response surface methodology

Improvement of performance of ultra-high performance concrete based composite material added with nano materials

Directory of Open Access Journals (Sweden)

Pang Jinchang

2016-03-01

Full Text Available Ultra-high performance concrete (UHPC, a kind of composite material characterized by ultra high strength, high toughness and high durability. It has a wide application prospect in engineering practice. But there are some defects in concrete. How to improve strength and toughness of UHPC remains to be the target of researchers. To obtain UHPC with better performance, this study introduced nano-SiO2 and nano-CaCO3 into UHPC. Moreover, hydration heat analysis, X-Ray Diffraction (XRD, mercury intrusion porosimetry (MIP and nanoindentation tests were used to explore hydration process and microstructure. Double-doped nanomaterials can further enhance various mechanical performances of materials. Nano-SiO2 can promote early progress of cement hydration due to its high reaction activity and C-S-H gel generates when it reacts with cement hydration product Ca(OH2. Nano-CaCO3 mainly plays the role of crystal nucleus effect and filling effect. Under the combined action of the two, the composite structure is denser, which provides a way to improve the performance of UHPC in practical engineering.

Study on grafting of different types of acrylic monomers onto natural rubber by γ-rays

International Nuclear Information System (INIS)

Dafader, N.C.; Haque, M.E.; Akhtar, F.; Ahmad, M.U.

2006-01-01

A comparative study of various acrylic monomers for grafting onto natural rubber was done. The stability of natural rubber latex (NRL) against coagulum with monomer, mechanical properties of grafted rubbers and percent of grafting were investigated. The NRL with monomers, methylacrylate (MA), ethylacrylate (EA) and n-butylacrylate (n-BA), is unstable but it is stable with methyl methacrylate (MMA), n-butyl methacrylate (BMA) and cyclohexyl methacrylate (CHMA). The mechanical properties and degree of grafting attained a maximum at a total radiation dose of 4 kGy. The values of tensile properties of MMA and CHMA grafted rubbers are almost similar, and higher than those of BMA grafted rubbers. On the other hand, the degree of grafting for CHMA is higher than those of MMA and BMA grafted rubbers. The infrared (IR) spectra of monomer grafted natural rubber were also studied

Organosulfonic acid-functionalized mesoporous composites based on natural rubber and hexagonal mesoporous silica

Energy Technology Data Exchange (ETDEWEB)

Nuntang, Sakdinun; Poompradub, Sirilux [Fuels Research Center, Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand); Butnark, Suchada [PTT Research and Technology Institute, PTT Public Company Limited, Wangnoi, Ayutthaya 13170 (Thailand); Yokoi, Toshiyuki; Tatsumi, Takashi [Chemical Resources Laboratory, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8503 (Japan); Ngamcharussrivichai, Chawalit, E-mail: Chawalit.Ng@Chula.ac.th [Fuels Research Center, Department of Chemical Technology, Faculty of Science, Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand); Center of Excellence on Petrochemical and Materials Technology (PETROMAT), Chulalongkorn University, Patumwan, Bangkok 10330 (Thailand)

2014-10-15

This study is the first report on synthesis, characterization and catalytic application of propylsulfonic acid-functionalized mesoporous composites based on natural rubber (NR) and hexagonal mesoporous silica (HMS). In comparison with propylsulfonic acid-functionalized HMS (HMS-SO{sub 3}H), a series of NR/HMS-SO{sub 3}H composites were prepared via an in situ sol–gel process using tetrahydrofuran as the synthesis media. Tetraethylorthosilicate as the silica source, was simultaneously condensed with 3-mercaptopropyltrimethoxysilane in a solution of NR followed by oxidation with hydrogen peroxide to achieve the mesoporous composites containing propylsulfonic acid groups. Fourier-transform infrared spectroscopy and {sup 29}Si MAS nuclear magnetic resonance spectroscopy results verified that the silica surfaces of the NR/HMS-SO{sub 3}H composites were functionalized with propylsulfonic acid groups and covered with NR molecules. After the incorporation of NR and organo-functional group into HMS, the hexagonal mesostructure remained intact concomitantly with an increased framework wall thickness and unit cell size, as evidenced by the X-ray powder diffraction analysis. Scanning electron microscopy analysis indicated a high interparticle porosity of NR/HMS-SO{sub 3}H composites. The textural properties of NR/HMS-SO{sub 3}H were affected by the amount of MPTMS loading to a smaller extent than that of HMS-SO{sub 3}H. NR/HMS-SO{sub 3}H exhibited higher hydrophobicity than HMS-SO{sub 3}H, as revealed by H{sub 2}O adsorption–desorption measurements. Moreover, the NR/HMS-SO{sub 3}H catalysts possessed a superior specific activity to HMS-SO{sub 3}H in the esterification of lauric acid with ethanol, resulting in a higher conversion level. - Highlights: • Acidic NR/HMS-SO{sub 3}H composites were prepared by in situ sol–gel process. • Propylsulfonic acid was functionalized onto HMS surface by direct co-condensation. • NR/HMS-SO{sub 3}H exhibited a hexagonal

Application of mathematical planning in production of filled emulsion rubbers

Science.gov (United States)

Pugacheva, I. N.; Molokanova, L. V.; Popova, L. V.; Repin, P. S.

2018-05-01

The applicability of mathematical planning of experiment in the field of chemistry and chemical engineering, in particular in the industrial production of synthetic rubbers, is considered in the article. Possibility of using secondary material resources, which are waste products of light industry, in the production of elastomeric compositions is studied. The method of obtaining a powdered cellulose additive from wastes containing cellulose fiber is described. The best way of introducing the obtained additive into elastomeric compositions based on the emulsion rubber is established. Optimal conditions for obtaining filled emulsion rubber with the help of a powdered cellulose additive were established basing on the mathematical planning of experiment.

Performance of kevlar fibre-reinforced rubber composite armour against shaped-charge jet penetration

Directory of Open Access Journals (Sweden)

Xu-dong Zu

Full Text Available AbstractThe protective capability of the Kevlar fibre-reinforced rubber composite armour (KFRRCA at different obliquities is studied using depth-of-penetration experiments method against a 56 mm-diameter standard-shaped charge. Efficiency factors are calculated to evaluate the protection capability of the KFRRCA at different obliquities. Meanwhile, an X-ray experiment is used to observe the deformation, fracture, and scatter of the shaped-charge jet as it penetrates the composite armour. Finally, scanning electron microscopy (SEM is used to analyse the effect of the Kevlar fibre-reinforced rubber for the composite armour to resist jet penetration. The results showed that the KFEECA can be used as additional armour, because it has excellent protection capability, and it can disturb the stability of the middle part of the shaped charge jet (SCJ obviously especially when the armour at 30°and 68° obliquities.

Microstructure and mechanical properties of aluminum–fly ash nano composites made by ultrasonic method

International Nuclear Information System (INIS)

Narasimha Murthy, I.; Venkata Rao, D.; Babu Rao, J.

2012-01-01

Highlights: ► Nano structured fly ash has been produced by 30 h milling time. ► Al–fly ash nano composites were produced by ultrasonic cavitation route. ► A homogeneous distribution of nano fly ash particles was observed in the matrix. ► No additional contamination in the nano composites from the atmosphere. ► Presence of nano fly ash leads to improvement in the strength of the composites. -- Abstract: In this paper an attempt has been made to modify the micro sized fly ash into nano structured fly ash using high energy ball mill. Ball milling was carried out for the total duration of 30 h. The sample was taken out after every 5 h of milling for characterizing. The nano structured fly ash was characterized for its crystallite size and lattice strain by using X-ray diffractometer. It was found that a steady decrease in the crystallite size and increased lattice strain was observed with milling time; the crystallite size at 30 h milling time was found to be 23 nm. The fresh fly ash particles are mostly spherical in shape; whereas the shape of the 30 h milled fly ash particles is irregular and the surface morphology is rough. Al–fly ash nano composites were produced by ultrasonic cavitation route successfully. Scanning electron microscopy images of nano composites reveal a homogeneous distribution of the nano fly ash particles in the AA 2024 matrix. Energy dispersive spectroscopy analysis of nano composites reveals that the fabricated nano composite did not contain any additional contamination from the atmosphere. As the amount of nano fly ash is increasing the hardness of the composite also increasing. The nano fly ash addition leads to improvement in the compression strength of the composites.

Effects of variation of oil and zinc oxide type on the gas barrier and mechanical properties of chlorobutyl rubber/epoxidised natural rubber blends

International Nuclear Information System (INIS)

Li, Lin; Zhang, Jin; Jo, Jae Ok; Datta, Sanjoy; Kim, Jin Kuk

2013-01-01

Highlights: ► A (90:10) blend of CIIR and ENR by weight was used as the base. ► Different process oil and ZnO were used to optimize the gas barrier property. ► The minimum oxygen permeability is obtained using sheet ZnO. - Abstract: In many polymer applications such as inner tire liners and fuel hoses, imparting excellent gas barrier property is of prime importance. Researches in this direction had been done based on a judicious choice of polymer type or a blend thereof and the compounding ingredients. Though butyl rubber has been the polymer of choice because of its excellent gas barrier property, yet researches were targeted to improve the same with further modification in the polymer type and variation in compounding ingredients. In this study, a (90:10) blend of chlorobutyl rubber (CIIR) and Epoxdised Natural Rubber (ENR) by weight was used as the base. Four different types of process oil and three different types of zinc oxide (ZnO) at fixed predetermined concentrations were used to optimize the gas barrier and mechanical properties. In this blend, recycled aromatic oil (RAE) and sheet zinc oxide were effective in imparting the best overall combination of properties. Scanning Electron Microscopic (SEM) studies of ZnO were done to understand the structure property relationship

Fracture surface analysis on nano-SiO{sub 2}/epoxy composite

Energy Technology Data Exchange (ETDEWEB)

Zhao Rongguo [Institute of Fundamental Mechanics and Material Engineering, Xiangtan University, Hunan 411105 (China); Key Laboratory of Low Dimensional Materials and Application Technology, Xiangtan University, Ministry of Education, Hunan 411105 (China)], E-mail: zhaorongguo@xtu.edu.cn; Luo Wenbo [Institute of Fundamental Mechanics and Material Engineering, Xiangtan University, Hunan 411105 (China); Key Laboratory of Low Dimensional Materials and Application Technology, Xiangtan University, Ministry of Education, Hunan 411105 (China)

2008-06-15

Fracture surface morphologies of nano-SiO{sub 2}/epoxy composite with different weight percentage of SiO{sub 2} are investigated using scanning electron microscopy. Two types of curing agent, dimethylbenzanthracene (DMBA) and methyltetrahydrophthalic anhydride (MeTHPA), are individually used for preparing the composites. It is found that the fracture surface morphology of the composite cured by DMBA shows as radial striations, which suggests a rapid brittle fracture mode, while the fracture surface morphology of the composite cured by MeTHPA shows as regularly spaced 'rib' markings, which indicates a stick-slip motion during the fracture process. Furthermore, the uniaxial tensile behavior under constant loading rate and ambient temperature are investigated. It is shown that the elastic modulus of the composite cured by DMBA firstly increases, and then decreases with the mass fraction of nano-SiO{sub 2} particles, but the elongation of the composite cured by MeTHPA is reversed with increasing fraction of nano-SiO{sub 2} particles. For nano-SiO{sub 2}/epoxy composite cured with MeTHPA that possesses a suitable fraction of nano-SiO{sub 2}, an excellent synthetic mechanical property on elastic modulus and elongation is obtained.

Reinforcing effect of plasma modified halloysite nanotubes in a carbon black filled natural rubber-butadien rubber matrix

NARCIS (Netherlands)

Poikelispaa, Minna; Das, Amit; Dierkes, Wilma K.; Vuorinen, Jyrki

2011-01-01

Rubber composites are generally produced by the direct incorporation of fillers like carbon black and/or silica into the rubber matrix. The incorporation of different types of nanofillers is the subject of recent research with the aim of preparing composites with special compositions and properties.

A comparative study of natural rubber modified with ground tire rubber of truck

OpenAIRE

Binti Haridan, Ili Liyana

2016-01-01

The recycling of waste rubber has considerable significance in term of environmental protection and energy conservation. Considering that most of the relevant literature is concerned with tire recycling, the aim of this work was to develop and characterize the elastomeric samples of natural rubber (NR) composites filled with ground tire rubber of truck (GTR) devulcanized by microwave (DGTR). The tire rubber was ground under ambient conditions and subjected to microwave exposure for 3, 5 and ...

Effects of Thermal and Humidity Aging on the Interfacial Adhesion of Polyketone Fiber Reinforced Natural Rubber Composites

OpenAIRE

Lee, Han Ki; Kim, Dae Sik; Won, Jong Sung; Jin, Da Young; Lee, Hyun Jae; Lee, Seung Goo

2016-01-01

Polyketone fiber is considered as a reinforcement of the mechanical rubber goods (MRG) such as tires, automobile hoses, and belts because of its high strength and modulus. In order to apply it to those purposes, the high adhesion of fiber/rubber interface and good sustainability to aging conditions are very important. In this study, polyketone fiber reinforced natural rubber composites were prepared and they were subjected to thermal and humidity aging, to assess the changes of the interfacia...

Electroless Ni-P/Nano-SiO2 Composite Plating on Dual Phase Magnesium-Lithium Alloy

Science.gov (United States)

Zou, Y.; Zhang, Z. W.; Zhang, M. L.

The application of Mg-Li alloys is restricted in practice due to mainly poor corrosion resistance and wear resistance. Electroless nickel plating is one of the common and effective ways to protect alloys from corrosion. In this study, nano-SiO2 particles with Ni-P matrix have been successfully co-deposited onto dual phase Mg-8Li base alloy through electroless plating, generating homogeneously Ni-P/nano-SiO2 composite coating. The morphology, elemental composition and structures of coatings were investigated. Coating performances were evaluated using hardness tests and electrochemical analysis. The results indicate that the Ni-P/nano-SiO2 composite coating can significantly improve the wear and corrosion resistance.

Optical Properties and Surface Morphology of Nano-composite PMMA: TiO2 Thin Films

International Nuclear Information System (INIS)

Lyly Nyl Ismail; Ahmad Fairoz Aziz; Habibah Zulkefle

2011-01-01

There are two nano-composite PMMA: TiO 2 solutions were prepared in this research. First solution is nano-composite PMMA commercially available TiO 2 nanopowder and the second solution is nano-composite PMMA with self-prepared TiO 2 powder. The self-prepared TiO 2 powder is obtained by preparing the TiO 2 sol-gel. Solvo thermal method were used to dry the TiO 2 sol-gel and obtained TiO 2 crystal. Ball millers were used to grind the TiO 2 crystal in order to obtained nano sized powder. Triton-X was used as surfactant to stabilizer the composite between PMMA: TiO 2 . Besides comparing the nano-composite solution, we also studied the effect of the thin films thickness on the optical properties and surface morphology of the thin films. The thin films were deposited by sol-gel spin coating method on glass substrates. The optical properties and surface characterization were measured with UV-VIS spectrometer equipment and atomic force microscopy (AFM). The result showed that nano-composite PMMA with self prepared TiO 2 give high optical transparency than nano-composite PMMA with commercially available TiO 2 nano powder. The results also indicate as the thickness is increased the optical transparency are decreased. Both AFM images showed that the agglomerations of TiO 2 particles are occurred on the thin films and the surface roughness is increased when the thickness is increased. High agglomeration particles exist in the AFM images for nano-composite PMMA: TiO 2 with TiO 2 nano powder compare to the other nano-composite solution. (author)

Oxidation Behavior of AlN/h-BN Nano Composites at High Temperature

International Nuclear Information System (INIS)

Jin Haiyun; Huang Yinmao; Feng Dawei; He Bo; Yang Jianfeng

2011-01-01

Both AlN/ nano h-BN composites and AlN/ micro h-BN composites were fabricated. The high temperature oxidation behaviors were investigated at 1000deg. C and 1300deg. C using a cycle-oxidation method. The results showed that there were little changes of both nano composites and monolithic AlN ceramic at temperature of 1000deg. C. And at 1300deg. C, the oxidation dynamics curve of composites could be divided into two courses: a slowly weight increase and a rapid weight decrease, but the oxidation behavior of nano composites was better than micro composites. It was due to that the uniform distribution of oxidation production (Al 18 B 4 O 33 ) surround the AlN grains in nano composites and the oxidation proceeding was retarded. The XRD analysis and SEM observations showed that there was no BN remained in the composites surface after 1300deg. C oxidation and the micropores remain due to the vaporizing of B 2 O 3 oxidized by BN.

Investigation on Nano composite Membrane of Multi walled Carbon Nano tube Reinforced Polycarbonate Blend for Gas Separation

International Nuclear Information System (INIS)

Kausar, A.

2016-01-01

Carbon nano tube has been explored as a nano filler in high performance polymeric membrane for gas separation. In this regard, nano composite membrane of polycarbonate (PC), poly(vinylidene fluoride-co-hexafluoropropylene) (PVFHFP), and multi walled carbon nano tube (MWCNT) was fabricated via phase inversion technique. Poly (ethylene glycol) (PEG) was employed for the compatibilization of the blend system. Two series of PC/PVFHFP/PEG were developed using purified P-MWCNT and acid functional A-MWCNT nano filler. Scanning and transmission electron micrographs have shown fine nano tube dispersion and wetting by matrix, compared with the purified system. Tensile strength and Young s modulus of PC/PVFHFP/PEG/MWCNT-A 1-5 were found to be in the range of 63.6-72.5 MPa and 110.6-122.1 MPa, respectively. The nano composite revealed 51% increase in Young s modulus and 28% increase in tensile stress relative to the pristine blend. The A-MWCNT was also effective in enhancing the perm selectivity αCO 2 /N 2 (31.2-39.9) of nano composite membrane relative to the blend membrane (21.6). The permeability ρCO 2 of blend was 125.6 barrer; however, the functional series had enhancedρCO 2 values ranging from 142.8 to 186.6 barrer. Moreover, A-MWCNT loading improved the gas diffusivity of PC/PVFHFP/PEG/MWCNT-A 1-5; however, filler content did not significantly influence the CO 2 and N 2 solubility.

Single-layer nano-carbon film, diamond film, and diamond/nano-carbon composite film field emission performance comparison

International Nuclear Information System (INIS)

Wang, Xiaoping; Wang, Jinye; Wang, Lijun

2016-01-01

A series of single-layer nano-carbon (SNC) films, diamond films, and diamond/nano-carbon (D/NC) composite films have been prepared on the highly doped silicon substrate by using microwave plasma chemical vapor deposition techniques. The films were characterised by scanning electron microscopy, Raman spectroscopy, and field emission I-V measurements. The experimental results indicated that the field emission maximum current density of D/NC composite films is 11.8–17.8 times that of diamond films. And the field emission current density of D/NC composite films is 2.9–5 times that of SNC films at an electric field of 3.0 V/μm. At the same time, the D/NC composite film exhibits the advantage of improved reproducibility and long term stability (both of the nano-carbon film within the D/NC composite cathode and the SNC cathode were prepared under the same experimental conditions). And for the D/NC composite sample, a high current density of 10 mA/cm"2 at an electric field of 3.0 V/μm was obtained. Diamond layer can effectively improve the field emission characteristics of nano-carbon film. The reason may be due to the diamond film acts as the electron acceleration layer.

Gamma radiation effects on nano composites of Ag nanoparticles in Zn O matrices

International Nuclear Information System (INIS)

Villasenor C, L. S.

2015-01-01

The study of gamma radiation effects in nano composites of silver nanoparticles in a Zn O matrix has been performed in this work. First, silver nanoparticles (AgNPs) were synthesized by colloidal methods, with two different mean average sizes, 48 nm and 24 nm respectively. These nanoparticles were characterized by transmission electron microscopy (Tem) and UV-Vis spectroscopy (UV-Vis). Then, with the synthesized AgNPs, nano composites in a matrix of Zn O were prepared. The first nano composite was prepared with the 48 nm AgNPs at 9.5 weight % of silver (Ag) and the second nano composite with the 24 nm nanoparticles at 1.0 weight % of Ag. Both nano composites were analyzed by scanning electron microscopy (Sem). The formation of the Zn O phase in the nano composite was corroborated through X-ray diffraction analysis. It was observed that the presence of AgNPs during the formation of the AgNPs/Zn O nano composite modified the size and morphology of the structures obtained compared to those of the pure Zn O without nanoparticles, however both exhibit a radial structure. Then, the nano composite at 9.5 weight % of Ag was irradiated with gamma rays at doses of 1, 20 and 50 kGy. Samples were analyzed by Sem and the Bet technique, before and after being irradiated, in order to determine the effect of gamma radiation in the morphology, porosity and surface area of the studied material. Even when there are changes in porosity and Surface area, this difference is not very significant for some applications, however it will have to be considered during the design of a specific application of the nano composites. On the other hand, no morphology modifications were identified on the samples irradiated at the studied doses, with the electron microscopy techniques used. (Author)

Preparation and characterization of novel nanocomposite films formed from silk fibroin and nano-TiO2.

Science.gov (United States)

Feng, Xin-Xing; Zhang, Li-Li; Chen, Jian-Yong; Guo, Yu-Hai; Zhang, Hua-Peng; Jia, Chang-Ian

2007-01-30

This paper describes the synthesis and characterization of new regenerated silk fibroin (SF)/nano-TiO(2) composite films. The preparation method, based on the sol-gel technique using butyl titanate as oxide precursor, could avoid reagglomeration of the prepared nanoparticles. Samples were characterized mainly by X-ray diffraction (XRD), ultra-violet (UV) spectroscopy, atomic force microscopy (AFM), Fourier transform infrared (FT-IR) spectroscopy, and thermogravimetric analysis (TGA). The UV and AFM results indicated that TiO(2) nanoparticles could be well dispersed inside the SF film, and the size of TiO(2) was about 80nm. The XRD and FT-IR analysis implied that the formation of nano-TiO(2) particles may induce the conformational transition of silk fibroin to a typical Silk II structure partly with the increasing of crystallinity in the composite films. Compared to the pure SF films, the mechanical and thermal properties of composite films were improved, and the solubility in water was decreased due to the conformational transition of silk fibroin to Silk II structure.

Graphene–Noble Metal Nano-Composites and Applications for Hydrogen Sensors

Directory of Open Access Journals (Sweden)

Sukumar Basu

2017-10-01

Full Text Available Graphene based nano-composites are relatively new materials with excellent mechanical, electrical, electronic and chemical properties for applications in the fields of electrical and electronic devices, mechanical appliances and chemical gadgets. For all these applications, the structural features associated with chemical bonding that involve other components at the interface need in-depth investigation. Metals, polymers, inorganic fibers and other components improve the properties of graphene when they form a kind of composite structure in the nano-dimensions. Intensive investigations have been carried out globally in this area of research and development. In this article, some salient features of graphene–noble metal interactions and composite formation which improve hydrogen gas sensing properties—like higher and fast response, quick recovery, cross sensitivity, repeatability and long term stability of the sensor devices—are presented. Mostly noble metals are effective for enhancing the sensing performance of the graphene–metal hybrid sensors, due to their superior catalytic activities. The experimental evidence for atomic bonding between metal nano-structures and graphene has been reported in the literature and it is theoretically verified by density functional theory (DFT. Multilayer graphene influences gas sensing performance via intercalation of metal and non-metal atoms through atomic bonding.

Electrical and Thermo-Mechanical properties of Irradiated Clay Nanoparticle/SBR Composites

International Nuclear Information System (INIS)

Ata, M.M.E.M.

2011-01-01

Polymer-Composites incorporating metal, semiconductors, Carbon black, nano materials and Clay materials have been widely used and studied as multifunctional materials with inherent polymer properties. Polymer-clay nano composites show remarkable property improvement when compared to conventionally scaled composites. For designing new materials with desirable, predicted properties, a better understanding of structure-property relationships is necessary. In this work, we employ dielectric relaxation spectroscopy (DRS) to investigate molecular mobility in relation to morphology in styrene butadiene rubber-SBR (treated and untreated) nano composites. In addition to the investigation of dipolar processes, special attention is paid here to the investigation of conductivity effects and mechanical as well as thermo-mechanical properties. From the stress-strain characteristics, one found that, all the compositions showed a tensile strength higher than the virgin rubber. By increasing the filler loading, the tensile strength of the prepared composites increases. The elongation at break for treated and untreated clay filed composites increases with an increase in filer loading up to 10 p hr and then followed by a decrease up to 15 p hr. The cross linking density, υ increases with both treated and untreated clay contents and treated samples have higher increasing rate of υ values than untreated one. To elucidate the tensile behavior of the test samples. The Ht model is tested by using non-Gaussian chain statistics, which give a good fitting with the experimental data.

Nitrile rubber and carboxylated nitrile rubber resistance to soybean biodiesel

Directory of Open Access Journals (Sweden)

Felipe Nunes Linhares

2018-03-01

Full Text Available Abstract Biodiesel has been considered a suitable substitute for petroleum diesel, but their chemical composition differs greatly. For this reason, biodiesel interacts differently than petroleum diesel with various materials, including rubbers. Therefore, the resistance of some elastomers should be thoroughly evaluated, specifically those which are commonly used in automotive industry. Nitrile rubber (NBR is widely used to produce vehicular parts that are constantly in contact with fuels. This paper aimed to assess the resistance of carboxylated nitrile rubber (XNBR with 28% of acrylonitrile content to soybean biodiesel in comparison with non-carboxylated nitrile rubber samples, with high and medium acrylonitrile content (33 and 45%. NBR with medium acrylonitrile content showed little resistance to biodiesel. However, carboxylated nitrile rubber even with low acrylonitrile content had similar performance to NBR with high acrylonitrile content.

Hybrid Nano composite Membranes for PEMFC Applications

International Nuclear Information System (INIS)

Niepceron, F.

2008-03-01

This work aims at validating a new concept of hybrid materials for the realization of proton exchange membranes, an essential constituent of PEM fuel cells. The originality of this nano-composite hybrid concept corresponds to a separation of the membrane's properties. We investigated the preparation of composite materials based on an inert, relatively low cost, polymer matrix (PVDF-HFP) providing the mechanical stability embedding inorganic fillers providing the necessary properties o f proton-conduction and water retention. The first step of this work consisted in the modification of fumed silica to obtain a proton-conducting filler. An ionic exchange capacity (CEI) equal to 3 meq/g was obtained by the original grafting of sodium poly(styrene-sulfonate) chains from the surface of particles. Nano-composite hybrid membranes PVDF-HFP/functionalized silica were accomplished by a film casting process. The coupling of the morphological and physicochemical analyses validated the percolation of the inorganic phase for 30 wt.% of particles. Beyond 40 % of loading, measured protonic conductivity is higher than the reference membrane Nafion 112. Finally, these membranes presented high performances, above 0.8 W/cm 2 , in single-cell fuel cell tests. A compromise is necessary according to the rate of loading between performances in fuel cell and mechanical properties of the membrane. 50 % appeared as best choice with, until 90 C, a remarkable thermal stability of the performances. (author)

Magnetic nanoparticles based nano-composites: synthesis, contribution of the fillers dispersion and the chains conformation on the reinforcement properties

International Nuclear Information System (INIS)

Robbes, Anne-Sophie

2011-01-01

The mechanical properties of polymeric nano-composite films can be considerably enhanced by the inclusion of inorganic nanoparticles due to two main effects: (i) the local structure of fillers dispersion and (ii) the potential modification of the chains conformation and dynamics in the vicinity of the filler/polymer interface. However, the precise mechanisms which permit to correlate these contributions at nano-metric scale to the macroscopic mechanical properties of the materials are actually poorly described. In such a context, we have synthesized model nano-composites based on magnetic nanoparticles of maghemite γ-Fe 2 O 3 (naked or grafted with a polystyrene (PS) corona by radical controlled polymerization) dispersed in a PS matrix, that we have characterized by combining small angle scattering (X-Ray and neutron) and transmission electronic microscopy. By playing on different parameters such as the particle size, the concentration, or the size ratio between the grafted chains and the ones of the matrix in the case of the grafted fillers, we have obtained nano-composite films a large panel of controlled and reproducible controlled filler structures, going from individual nanoparticles or fractal aggregates up to the formation of a connected network of fillers. By applying an external magnetic field during the film processing, we succeeded in aligning the different structures along the direction of the field and we obtained materials with remarkable anisotropic reinforcement properties. The conformation of the chains of the matrix, experimentally determined thanks to the specific properties of neutron contrast of the system, is not affected by the presence of the fillers, whatever their confinement, the dispersion the fillers or their chemical state surface. The alignment of the fillers along the magnetic field has allowed us to describe precisely the evolution of the reinforcement modulus of the materials with the structural reorganization of the fillers and

BACTERICIDE IMPACT OF POLYMER-STABILIZED MULTI-FUNCTIONAL NANO-COMPOSITES

Directory of Open Access Journals (Sweden)

Graskova I.A.

2012-08-01

Full Text Available Synthesis on the basis of natural matrices in order to acquire products with the desired properties is one of the promising trends of modern science. Using polysaccharides as a matrix allowed to generate derivatives with diverse structures and new properties. Growing interest towards anti-microbe effect of selenium-containing nano-composites is induced by the phenomenon of antibiotic-resistance of contemporary pathogenic microorganisms.Clavibacter genus bacteria are the most significant and widely spread among gram-positive bacteria. Bacteria cells are static pleimorphous rods, normally singular, sometimes coupled or joined in short chains, strict anaerobes in need of certain growth factors, non-sporogenous. Clavibacter michiganensis subsp. sepedonicus cause potato ring rot. At the tuber slice the damage is shaped as a ring; growing bacteria are accumulated in the conducting vessels causing their occlusion and therefore gradual withering of leaves and stem. This disease is distributed at all the continents including Australia. Harvest loss through ring rot damage may reach 10-45%.Our work was aimed at the study of complex interaction between microbe cultivar and selenium-based nanocomposites. Bacterial strain Аs1405 was acquired from the All-Russia collection of microorganisms, IMBP RAS. This genus is not included in the classification of pathogenic microorganisms by pathogenic groups of Sanitary-Epidemiological Rules SP 1.3.2322-08. The present study was focused on characteristics of the acquired strain.Fluorescent and electronic-scanning microscope was used to acquire photographs of bacterial cells. Pathogen was identified by PCR-analysis, which confirmed the presence of DNA of desired size. The extracted DNA was sequenced with the sequenced sequence added to Gen Bank under the number HQ394204. Cellulolytic and phytotoxic activity of this strain was determined.Chemistry Institute named A.E. Favorsky provided water-soluble nano-composites

A nano lamella NbTi–NiTi composite with high strength

Energy Technology Data Exchange (ETDEWEB)

Jiang, Jiang [Jiangxi Key Laboratory of Advanced Copper and Tungsten Materials, Jiangxi Academy of Sciences, Nanchang 330029 (China); Institute of Applied Physics of Jiangxi Academy of Sciences, Nanchang 330029 (China); State Key Laboratory of Heavy Oil Processing and Department of Materials Science and engineering, China University of Petroleum, Beijing 102249 (China); Jiang, Daqiang [State Key Laboratory of Heavy Oil Processing and Department of Materials Science and engineering, China University of Petroleum, Beijing 102249 (China); School of Mechanical and Chemical Engineering, The University of Western Australia, WA 6009 (Australia); Hao, Shijie; Yu, Cun; Zhang, Junsong [State Key Laboratory of Heavy Oil Processing and Department of Materials Science and engineering, China University of Petroleum, Beijing 102249 (China); Ren, Yang [X-ray Science Division, Argonne National Laboratory, Argonne, IL 60439 (United States); Lu, Deping; Xie, Shifang [Jiangxi Key Laboratory of Advanced Copper and Tungsten Materials, Jiangxi Academy of Sciences, Nanchang 330029 (China); Institute of Applied Physics of Jiangxi Academy of Sciences, Nanchang 330029 (China); Cui, Lishan, E-mail: lishancui63@126.com [State Key Laboratory of Heavy Oil Processing and Department of Materials Science and engineering, China University of Petroleum, Beijing 102249 (China)

2015-05-01

A hypereutectic Nb{sub 60}Ti{sub 24}Ni{sub 16} (at%) alloy was prepared by vacuum induction melting, and a nano lamellae NbTi–NiTi composite was obtained by hot-forging and wire-drawing of the ingot. Microscopic analysis showed that NbTi and NiTi nano lamellae distributed alternatively in the composite, and aligned along the wire axial direction, with a high volume fraction (~70%) of NbTi nano lamellae. In situ synchrotron X-ray diffraction analysis revealed that stress induced martensitic transformation occurred upon loading, which would effectively weaken the stress concentration at the interface and avoid the introduction of defects into the nano reinforced phase. Then the embedded NbTi nano lamellae exhibited a high elastic strain up to 2.72%, 1.5 times as high as that of the Nb nanowires embedded in a conventional plastic matrix, and the corresponding stress carried by NbTi was evaluated as 2.53 GPa. The high volume fraction of NbTi nano lamellae improved the translation of high strength from the nano reinforced phase into bulk properties of the composite, with a platform stress of ~1.7 GPa and a fracture strength of ~1.9 GPa.

Antioxidant and sensitizer effect on the stability of natural rubber latex vulcanized by gamma rays

International Nuclear Information System (INIS)

Canavel, V.

1993-01-01

The natural rubber latex was vulcanized by gamma rays and electrons beam, in the presence and absence of sensitizer at room temperature. The sensitizers were the following; n-butyl acrylate (n-BA) / t-butyl hydroperoxide (t-B H) / KOH, C Cl 4 / potassium laurate and n-BA / KOH. The studied antioxidants, Irganox 1520, Vulcanox SP and Vulcanox BKF, were added to the latex after irradiation. Among the studied antioxidants in function of tensile strength (TS) after the aging of rubber plates, the Irganox was the best efficient on the gamma vulcanization in the presence of n-BA/t-B H/KOH, because only 0,20 p hr is enough to obtain the greatest increase of TS, that was 34%, 12 MPa to 16 MPa. The formulating method of latex with the sensitizer constituted the 3,0 p hr of n-BA/ 0,1 p hr of t-B H and 0,2 p hr of KOH, was evaluated respecting the TS of rubber plates. The electrons beam vulcanization produces the greatest reversible perturbance in the colloidal stability of latex after irradiation caused by radiolytic species absorption that promotes the increase of particle size. The antioxidant also contributes to reversible destabilization of gamma irradiated latex, because it is also adsorbed by particles surface. The relation between the latex viscosity and the TS of respective rubber plates is reverse, showing the latex stability affects the quality of rubber goods. (author)

Study of new rubber to steel adhesive systems based on Co(II and Cu(II sulphides coats

Directory of Open Access Journals (Sweden)

Labaj Ivan

2018-01-01

Full Text Available The presented paper deals with the preparation of new rubber to steel adhesive systems using the steel surface treatment with deposition of adhesive coats based on Co(II and Cu(II sulphides. Efficiency of new prepared adhesive systems containing Co(II and Cu(II sulphides has been compared with the efficiency of double layer adhesive system commonly used in industry. The chemical composition of prepared adhesive systems was determined using the EDX analysis. Scanning Electron Microscopy (SEM was used for study of topography and microstructure of prepared rubber to steel adhesive systems (Co(II, Cu(II sulphide, double layer adhesive system. For determination of adhesion strength between rubber blends and metal pieces with various adhesive systems deposited on these pieces, the test according to ASTM D429 standard relating to Rubber to metal adhesion, method A was used. For all test samples, the same type of rubber blend and the same curing conditions have been used.

About the cure kinetics in natural rubber/styrene Butadiene rubber blends at 433 K

International Nuclear Information System (INIS)

Mansilla, M.A.; Marzocca, A.J.

2012-01-01

Vulcanized blends of elastomers are employed in several goods mainly to improve physical properties and reduce costs. One of the most used blends of this kind is that composed by natural rubber (NR) and styrene butadiene rubber (SBR). The cure kinetic of these blends depends mainly on the compound formulation and the cure temperature and time. The preparation method of the blends can influence the mechanical properties of the vulcanized compounds. In this work the cure kinetic at 433 K of NR/SBR blends vulcanized with the system sulfur/TBBS (N-t-butyl-2-benzothiazole sulfenamide) is analyzed in samples prepared by mechanical mixing and solution blending. The two methods produce elastomer domains of NR and SBR, which present different microstructure due to the cure level attained during vulcanization. The cure kinetics is studied by means of rheometer tests and the model proposed by Kamal and Sourour. The analysis of the cure rate is presented and is related to the structure obtained during the vulcanization process.

About the cure kinetics in natural rubber/styrene Butadiene rubber blends at 433 K

Energy Technology Data Exchange (ETDEWEB)

Mansilla, M.A., E-mail: mmansilla@df.uba.ar [Laboratorio de Polimeros y Materiales Compuestos, Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pabellon 1, C1428EGA Buenos Aires (Argentina); Marzocca, A.J. [Laboratorio de Polimeros y Materiales Compuestos, Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pabellon 1, C1428EGA Buenos Aires (Argentina)

2012-08-15

Vulcanized blends of elastomers are employed in several goods mainly to improve physical properties and reduce costs. One of the most used blends of this kind is that composed by natural rubber (NR) and styrene butadiene rubber (SBR). The cure kinetic of these blends depends mainly on the compound formulation and the cure temperature and time. The preparation method of the blends can influence the mechanical properties of the vulcanized compounds. In this work the cure kinetic at 433 K of NR/SBR blends vulcanized with the system sulfur/TBBS (N-t-butyl-2-benzothiazole sulfenamide) is analyzed in samples prepared by mechanical mixing and solution blending. The two methods produce elastomer domains of NR and SBR, which present different microstructure due to the cure level attained during vulcanization. The cure kinetics is studied by means of rheometer tests and the model proposed by Kamal and Sourour. The analysis of the cure rate is presented and is related to the structure obtained during the vulcanization process.

Preparation and characterization of nano hydroxyapatite/polymeric composites materials. Part I

Energy Technology Data Exchange (ETDEWEB)

Mohamed, Khaled R., E-mail: kh_rezk1966@yahoo.com [Biomaterials Dept., National Research Centre, Dokki, Cairo (Egypt); El-Rashidy, Zenab M. [Biomaterials Dept., National Research Centre, Dokki, Cairo (Egypt); Salama, Aida A. [Biophysics Dept., Faulty of Science, El-Azhar Univ., Cairo (Egypt)

2011-10-17

Highlights: {yields} The formation and coating of CHA increased by increasing polymer content. {yields} The size of the prepared CHA was within nano-range scale. {yields} The composites had homogeneity and CHA formed within the polymeric matrix. - Abstract: The present study is focused on preparation of nano composite materials and the effect of citric acid on their different properties. The formation of nano HA and its interaction with chitosan (C), gelatin (G) polymers and citric acid (CA) materials were studied. The Fourier Transformed Infrared Spectroscopy (FT-IR), X-ray diffraction (XRD), thermo-gravimetric analysis (TGA), transmission electron microscope (TEM), and scanning electron microscope (SEM) were used to characterize these composite materials. The compressive strength (CS) was also measured to know the reinforcement of the prepared composites. The results show that carboxylic and amino groups play crucial role for HA formation on chitosan-gelatin polymeric matrix in the presence of citric acid (CA). The formation of nano HA particles and its average size of crystallite is increased with increase of CG content and decreased with addition of CA. Also, the HA formation and binding strength between its particles are improved into the composites especially with CA. The nano-composites containing the best ratio of nHA (70%) with CA (0.2 M) are promising for medical applications in the future.

Preparation and Photocatalytic Performance of Bamboo-Charcoal-Supported Nano-ZnO Composites

Directory of Open Access Journals (Sweden)

Yunlong ZHOU

2018-02-01

Full Text Available Nano-ZnO/bamboo charcoal composites were prepared by precipitation with bamboo charcoal as support. Nano-ZnO/bamboo charcoal composites were characterized by XRD, SEM and EDS. Photocatalytic degradation processes of methyl orange were studied. The results indicate that the structure of nano-ZnO is of the wurtzite type and the grain size is about 19-54 nm. The best preparation temperature for these composites is 500℃. The composites have better photocatalytic degradation ability than pure ZnO under UV irradiation. Photocatalytic degradation of methyl orange with the composites obeys first-order kinetics, and the composites can be recycled.DOI: http://dx.doi.org/10.5755/j01.ms.24.1.17397

Carboxy terminated rubber based on natural rubber grafted with acid anhydrides and its adhesion properties

International Nuclear Information System (INIS)

Klinpituksa, P; Kongkalai, P; Kaesaman, A

2014-01-01

The chemical modification of natural rubber by grafting of various polar functional molecules is an essential method, improving the versatility of rubber in applications. This research investigated the preparation of natural rubber-graft-citraconic anhydride (NR-g-CCA), natural rubber-graft-itaconic anhydride (NR-g-ICA), and natural rubber-graft-maleic anhydride (NR-g-MA), with the anhydrides grafted to natural rubber in toluene using benzoyl peroxide as an initiator. Variations of monomer content, initiator content, temperature and reaction time of the grafting copolymerization were investigated. The maximum degrees of grafting were 1.06% for NR-g-CCA, 4.66% for NR-g-ICA, and 5.03% for NR-g-MA, reached using 10 phr citraconic anhydride, 10 phr of itaconic anhydride, or 8 phr of maleic anhydride, 3 phr benzoyl peroxide, at 85, 80 and 80°C for 2, 2 and 3 hrs, respectively. Solvent-based wood adhesives were formulated from these copolymers with various contents of wood resin in the range 10-40 phr. The maximal 289 N/in cleavage peel and 245.7 KPa shear strength for NR-g-MA (5.03% grafting) were obtained at 40 phr wood resin

Preparation and characterization of composites based on the blends of collagen, chitosan and hyaluronic acid with nano-hydroxyapatite.

Science.gov (United States)

Sionkowska, Alina; Kaczmarek, Beata

2017-09-01

3D porous composites based on the blend of chitosan, collagen and hyaluronic acid with the addition of nano-hydroxyapatite were prepared. SEM images for the composites were made and the structure was assessed. Mechanical properties were studied using a Zwick&Roell Testing Mashine. In addition, the porosity and density of composites were measured. The concentration of calcium ions released from the material was detected by the complexometric titration method. The results showed that in 3D porous sponge based on the blend of chitosan, collagen and hyaluronic acid, inorganic particles of nanohydroxyapatite can be incorporated, as well as that the properties of 3D composites depend on the material composition. Mechanical parameters and thermal stability of ternary biopolymeric blends were improved by the addition of hydroxyapatite. Moreover, the porosity of ternary materials was higher than in materials based on pure chitosan or collagen. All composites were characterized by a porous structure with interconnected pores. Calcium ions can be released from the composite during its degradation in water. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of Anion on Behaviour of Li-S Battery Electrolyte Solutions Based on N-Methyl-N-Butyl-Pyrrolidinium Ionic Liquids

International Nuclear Information System (INIS)

Barghamadi, Marzieh; Best, Adam S.; Bhatt, Anand I.; Hollenkamp, Anthony F.; Mahon, Peter J.; Musameh, Mustafa; Rüther, Thomas

2015-01-01

The electrochemical behaviour and electrical performance are investigated for a series of lithium-sulfur (Li-S) cells in which the electrolyte solutions are organic solvent-ionic liquid mixtures that are based on the 1-butyl-1-methylpyrrolidinium (C 4 mpyr) cation with a range of anions. In each case, performance is compared with cells that are based on a standard mixed-ether organic electrolyte. The capacity of cells assembled with electrolytes containing 1-butyl-1-methylpyrrolidinium tris(pentafluoroethyl) trifluorophosphate (C 4 mpyr-FAP), 1-butyl-1-methylpyrrolidinium trifluoromethanesulfonate (C 4 mpyr-OTf), or 1-butyl-1-methylpyrrolidinium tricyanomethanide (C 4 mpyr-TCM) decline rapidly due to low conductivity, high polysulfide solubility and side reaction of electrolyte with electrodes, respectively. Our results confirm that polysulfide solubility is strongly controlled by the anion of the ionic liquid and verify that not all ionic liquids decrease polysulfide solubility. In agreement with previous reports, 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl) imide (C 4 mpyr-TFSI) shows the best compatibility in Li-S batteries and has a higher coulombic efficiency of greater than 99% over 100 cycles. Furthermore, impedance spectroscopy confirms that electrolyte composition influences the SEI layer formed on the lithium anode and its subsequent impedance.

Biomimetic properties of an injectable chitosan/nano-hydroxyapatite/collagen composite

Energy Technology Data Exchange (ETDEWEB)

Huang Zhi [Laboratory of Advanced Materials, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Feng Qingling, E-mail: biomater@mail.tsinghua.edu.cn [Laboratory of Advanced Materials, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Yu Bo; Li Songjian [Department of Orthopedics, Zhujiang Hospital of Southern Medical University, Guangzhou 510282 (China)

2011-04-08

To meet the challenges of designing an injectable scaffold and regenerating bone with complex three-dimensional (3D) structures, a biomimetic and injectable hydrogel scaffold based on nano-hydroxyapatite (HA), collagen (Col) and chitosan (Chi) is synthesized. The chitosan/nano-hydroxyapatite/collagen (Chi/HA/Col) solution rapidly forms a stable gel at body temperature. It shows some features of natural bone both in main composition and microstructure. The Chi/HA/Col system can be expected as a candidate for workable systemic minimally invasive scaffolds with surface properties similar to physiological bone based on scanning electron microscopic (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) results.

Biomimetic properties of an injectable chitosan/nano-hydroxyapatite/collagen composite

International Nuclear Information System (INIS)

Huang Zhi; Feng Qingling; Yu Bo; Li Songjian

2011-01-01

To meet the challenges of designing an injectable scaffold and regenerating bone with complex three-dimensional (3D) structures, a biomimetic and injectable hydrogel scaffold based on nano-hydroxyapatite (HA), collagen (Col) and chitosan (Chi) is synthesized. The chitosan/nano-hydroxyapatite/collagen (Chi/HA/Col) solution rapidly forms a stable gel at body temperature. It shows some features of natural bone both in main composition and microstructure. The Chi/HA/Col system can be expected as a candidate for workable systemic minimally invasive scaffolds with surface properties similar to physiological bone based on scanning electron microscopic (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) results.

Development of Nano TiO2–Geopolymer Functional Composite as Antifouling Bricks

Directory of Open Access Journals (Sweden)

Kusuma Wardani Nurul

2017-01-01

Full Text Available The purpose of study is to examine the ability of nano TiO2 – geopolymer functional composite as antifouling bricks. The samples were synthesized through alkali-activation method at 70°C for 1 hour by mixing metaclay with TiO2 nanoparticles and activated with sodium silicate solution. There were two series of samples produced, namely, GT_A with addition of 2% nanoTiO2 and GT_B with addition of 4% nano TiO2 relative to the mass of metaclay. The samples were immersed in water and in 1M H2SO4 solution for 4 days to examine the resistance of composites in hars environment. The x-ray diffraction (XRD was performed to examine the chemical compositions of the samples before and after environmental test. The morphology of the samples surfaces was examined by using Scanning Electron Microscopy (SEM coupled with energy dispersive spectroscopy (EDS. Based on this study, sample GT_A shows its excellent properties as antifouling bricks. The addition of nano TiO2 was found to improve the quality of geopolymers as a high performance bricks.

Radiochemical study of isomerization of free butyl cations

International Nuclear Information System (INIS)

Sinotova, E.N.; Nefedov, V.D.; Skorokhodov, S.S.; Arkhipov, Yu.M.

1987-01-01

Ion-molecular reactions of free butyl cations, generated by nuclear chemical method, with carbon monoxide containing small quantities of ethanol vapors are studied. Carbon monoxide was used to fix instable butyl cations in the form of corresponding acyl ions. Ester of α-methyl-butyric acid appears to be the only product of free butyl cation interaction with carbon monoxide in the presence of ethanol vapors. That means, that up to the moment of butyl cation reaction with carbon monoxide, the primary butyl cations are almost completely isomerized into secondary in agreement with results of previous investigations. This allows one to study free butyl cation isomerization process according to ion-molecular reaction product isomeric composition

AC/TiO2/Rubber Composite Sheet Catalysts; Fabrication, Characterization and Photocatalytic Activities

Directory of Open Access Journals (Sweden)

Sriwong Chaval

2015-01-01

Full Text Available The AC/TiO2/Rubber (ACTR composite sheets weresuccessfully fabricated by a simply mixing of fixed TiO2 suspension and natural rubber latex (60% HA contents withthe varyingamounts of activated carbon (AC suspension, followed by stirring, pouring into apetri dish mold, drying at room temperature (RT, after that taking out from a mold, reversing and drying again at RT. Then, the as-fabricated ACTR composite sheets were characterized by X-ray diffractometer (XRD, attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR, energy dispersive X-ray spectroscopy (EDS and scanning electron microscopy (SEMtechniques. The photocatalytic efficiencies of all ACTR composite sheet samples were evaluated by photo degrading of methylene blue (MB dye solution under UV light irradiation. The results showed that the photocatalytic activity of ACTR sheet with10.0wt%AC loading has the highest efficiency for the photo degradation of MB dye than the other sheets. This is due to the fact that it is relatively with the synergistic effect of well-combined titanium dioxide catalyst and activated carbon adsorbent.

CO oxidation on Alsbnd Au nano-composite systems

Science.gov (United States)

Rajesh, C.; Majumder, C.

2018-03-01

Using first principles method we report the CO oxidation behaviour of Alsbnd Au nano-composites in three different size ranges: Al6Au8, Al13Au42 and a periodic slab of Alsbnd Au(1 1 1) surface. The clusters prefer enclosed structures with alternating arrangement of Al and Au atoms, maximising Auδ-sbnd Alδ+ bonds. Charge distribution analysis suggests the charge transfer from Al to Au atoms, corroborated by the red shift in the density of states spectrum. Further, CO oxidation on these nano-composite systems was investigated through both Eley - Rideal and Langmuir Hinshelwood mechanism. While, these clusters interact with O2 non-dissociatively with an elongation of the Osbnd O bond, further interaction with CO led to formation of CO2 spontaneously. On contrary, the CO2 evolution by co-adsorption of O2 and CO molecules has a transition state barrier. On the basis of the results it is inferred that nano-composite material of Alsbnd Au shows significant promise toward effective oxidative catalysis.

Study of thermal properties and the dispersion state of nano composites epoxy/clay

International Nuclear Information System (INIS)

Paz, Juliana D.; Bertholdi, Jonas; Toledo, Tais C.; Folgueras, Marilena V.; Pezzin, Sergio H.; Coelho, Luiz A.F.

2011-01-01

This work investigates an exfoliation/intercalation of nano clays in an epoxy resin by means of x-rays diffraction, scanning electronic microscopy, thermal gravimetric analysis and dilatometric analysis. A comparison of two techniques for preparing nano composites is addressed: mechanical stirring and sonication. X-rays analysis showed that an exfoliation/intercalation is occurring in some samples. TG analysis indicated and increase in thermal stability of the nano composites compared to the neat resin. Finally, dilatometric analysis indicates and increase in Tg for nano composites compared to the neat resin. (author)

Structure and properties of oil palm-based nanocellulose reinforced chitosan nanocomposite for efficient synthesis of butyl butyrate.

Science.gov (United States)

Elias, Nursyafiqah; Chandren, Sheela; Attan, Nursyafreena; Mahat, Naji Arafat; Razak, Fazira Ilyana Abdul; Jamalis, Joazaizulfazli; Wahab, Roswanira Abdul

2017-11-15

In this study, nanocellulose (NC) was successfully extracted from oil palm frond leaves (OPFL) using a combination of bleaching, alkaline treatment and acid hydrolysis. X-ray diffractogram revealed the extracted NC was crystalline with a crystallinity index of 70.2%. This indicates its suitability as nano-fillers for preparing the chitosan/nanocellulose (CS-NC) supports to immobilize Candida rugosa lipase (CRL) to produce the CRL/CS-NC biocatalysts. FTIR, FESEM and TGA characterizations of the CRL/CS-NC confirm the CRLs were successfully conjugated to the CS-NC supports. The air-dried CS-NC supports gave satisfactory immobilization of the CRLs (5.2mg/g) with the resultant CRL/CS-NCs catalysed conversions of ≥80% of butyl butyrate within 6h. Time course reaction profile revealed that 76.3% butyl butyrate conversion was achieved at 4h immobilization time using 3mg/mL of CRL/CS-NCs. NMR analyses on the purified butyl butyrate confirmed that the ester was successfully synthesized. Copyright © 2017 Elsevier Ltd. All rights reserved.

Finite Element Model Characterization Of Nano-Composite Thermal And Environmental Barrier Coatings

Science.gov (United States)

Yamada, Yoshiki; Zhu, Dongming

2011-01-01

Thermal and environmental barrier coatings have been applied for protecting Si based ceramic matrix composite components from high temperature environment in advanced gas turbine engines. It has been found that the delamination and lifetime of T/EBC systems generally depend on the initiation and propagation of surface cracks induced by the axial mechanical load in addition to severe thermal loads. In order to prevent T/EBC systems from surface cracking and subsequent delamination due to mechanical and thermal stresses, T/EBC systems reinforced with nano-composite architectures have showed promise to improve mechanical properties and provide a potential crack shielding mechanism such as crack bridging. In this study, a finite element model (FEM) was established to understand the potential beneficial effects of nano-composites systems such as SiC nanotube-reinforced oxide T/EBC systems.

A comparative study on low cycle fatigue behaviour of nano and micro Al2O3 reinforced AA2014 particulate hybrid composites

Directory of Open Access Journals (Sweden)

R. Senthilkumar

2015-01-01

Full Text Available Aluminium based metal matrix composites have drawn more attraction due to their improved properties in structural applications for the past two decades. The fatigue behaviour of composite materials needs to be studied for their structural applications. In this work, powder metallurgy based aluminium (AA2014 alloy reinforced with micro and nano-sized alumina particles were fabricated and consolidated with the hot extrusion process. The evaluation of mechanical properties in the extruded composite was carried out. This composite was subjected to low cycle fatigue test with a constant strain rate. Scanning Electron Microscope (SEM and Transmission Electron Microscope (TEM images were used to evaluate the fatigue behaviour of aluminium-nano composite samples. Enhanced mechanical properties were exhibited by the nano alumina reinforced aluminium composites, when compared to the micron sized alumina reinforced composites. The failure cycle is observed to be higher for the nano alumina reinforced composites when compared with micron sized alumina composites due to a lower order of induced plastic strain.

PREFACE: International Conference on Structural Nano Composites (NANOSTRUC 2012)

Science.gov (United States)

Njuguna, James

2012-09-01

Dear Colleagues It is a great pleasure to welcome you to NanoStruc2012 at Cranfield University. The purpose of the 2012 International Conference on Structural Nano Composites (NanoStruc2012) is to promote activities in various areas of materials and structures by providing a forum for exchange of ideas, presentation of technical achievements and discussion of future directions. NanoStruc brings together an international community of experts to discuss the state-of-the-art, new research results, perspectives of future developments, and innovative applications relevant to structural materials, engineering structures, nanocomposites, modelling and simulations, and their related application areas. The conference is split in 7 panel sessions, Metallic Nanocomposites and Coatings, Silica based Nanocomposites, safty of Nanomaterials, Carboin based Nanocomposites, Multscale Modelling, Bio materials and Application of Nanomaterials. All accepted Papers will be published in the IOP Conference Series: Materials Science and Engineering (MSE), and included in the NanoStruc online digital library. The abstracts will be indexed in Scopus, Compedex, Inspec, INIS (International Nuclear Information System), Chemical Abstracts, NASA Astrophysics Data System and Polymer Library. Before ending this message, I would like to acknowledge the hard work, professional skills and efficiency of the team which ensured the general organisation. As a conclusion, I would like to Welcome you to the Nanostruc2012 and wish you a stimulating Conference and a wonderful time. On behalf of the scientific committee, Signature James Njuguna Conference Chair The PDF of this preface also contains committee listings and associates logos.

Development of radiation-curable resin based on natural rubber

Energy Technology Data Exchange (ETDEWEB)

Mohd, Dahlan; Harun, Abdul Ghani [Nuclear Energy Unit, Bangi, Selangor (Malaysia)

1994-12-31

A new radiation curable resin based on natural rubber has been developed. The resin was based on the reaction between low molecular weight epoxidised natural rubber and acrylic acid. When formulated with reactive monomers and photoinitiator, it solidified upon irradiation with UV light. The resin may find applications in coating for cellulosic-based substrates and pressure-sensitive adhesive.

Development of radiation-curable resin based on natural rubber

International Nuclear Information System (INIS)

Dahlan Mohd; Abdul Ghani Harun

1993-01-01

A new radiation curable resin based on natural rubber has been developed. The resin was based on the reaction between low molecular weight epoxidised natural rubber and acrylic acid. When formulated with reactive monomers and photoinitiator, it solidified upon irradiation with UV light. The resin may find applications in coating for cellulosic-based substrates and pressure-sensitive adhesive

Radiation Induced Grafting of Acrylate onto Waste Rubber: The Effect of Monomer Type

Directory of Open Access Journals (Sweden)

Shirajuddin Siti Salwa M.

2017-01-01

Full Text Available The effect of three different acrylate group monomers, namely n-butyl acrylate, methacrylic acid and tripropylene glycol diacrylate of radiation induced grafting onto waste rubber was studied. The electron beam accelerator operated at voltage of 2MeV was used to irradiate the waste rubber at 10 kGy and 100 kGy absorbed radiation dose, respectively. The formation of grafting was observed from the increase in the grafting yield and confirmed by Transformed Infra-Red Spectroscopy results. According to the result obtained, only tripropylene glycol diacrylate was selected to graft onto waste rubber. The carbonyl bond from acrylate groups was seen at 1726 cm-1 band which confirmed the presence of TPGDA in the polymer matrix. This indicates the successful preparation of the TPGDA-grafted waste rubber via radiation induced grafting techniques.

3D silicone rubber interfaces for individually tailored implants.

Science.gov (United States)

Stieghorst, Jan; Bondarenkova, Alexandra; Burblies, Niklas; Behrens, Peter; Doll, Theodor

2015-01-01

For the fabrication of customized silicone rubber based implants, e.g. cochlear implants or electrocortical grid arrays, it is required to develop high speed curing systems, which vulcanize the silicone rubber before it runs due to a heating related viscosity drop. Therefore, we present an infrared radiation based cross-linking approach for the 3D-printing of silicone rubber bulk and carbon nanotube based silicone rubber electrode materials. Composite materials were cured in less than 120 s and material interfaces were evaluated with scanning electron microscopy. Furthermore, curing related changes in the mechanical and cell-biological behaviour were investigated with tensile and WST-1 cell biocompatibility tests. The infrared absorption properties of the silicone rubber materials were analysed with fourier transform infrared spectroscopy in transmission and attenuated total reflection mode. The heat flux was calculated by using the FTIR data, emissivity data from the infrared source manufacturer and the geometrical view factor of the system.

Electrochemically deposited BiTe-based nano wires for thermoelectric applications

International Nuclear Information System (INIS)

Inn-Khuan, N.; Kuan-Ying, K.; Che Zuraini Che Abdul Rahman; Nur Ubaidah Saidin; Suhaila Hani Ilias; Thye-Foo, C.

2013-01-01

Full-text: Nano structured materials systems such as thin-films and nano wires (NWs) are promising for thermoelectric power generation and refrigeration compared to traditional counterparts in bulk, due to their enhanced thermoelectric figures-of-merit. BiTe and its derivative compounds, in particular, are well-known for their near-room temperature thermoelectric performance. In this work, both the binary and ternary BiTe-based nano wires namely, BiTe and BiSbTe, were synthesized using template-assisted electrodeposition. Diameters of the nano wires were controlled by the pore sizes of the anodised alumina (AAO) templates used. Systematic study on the compositional change as a function of applied potential was carried out via Linear Sweep Voltametry (LSV). Chemical compositions of the nano wires were studied using Energy Dispersive X-ray Spectrometry (EDXS) and their microstructures evaluated using diffraction and imaging techniques. Results from chemical analysis on the nano wires indicated that while the Sb content in BiSbTe nano wires increased with more negative deposition potentials, the formation of Te 0 and Bi 2 Te 3 were favorable at more positive potentials. (author)

SiO2@FeSO4 nano composite: A recoverable nano-catalyst for eco-friendly synthesis oximes of carbonyl compounds

Directory of Open Access Journals (Sweden)

Mostafa Karimkoshteh

2016-01-01

Full Text Available Various aldoximes and ketoximes synthesis of corresponding aldehydes and ketones in the presence of SiO2@FeSO4 nano composite as recoverable nano catalyst and NH2OH·HCl. The SiO2@FeSO4 nano composite system was carried out between 10 to 15 min in oil bath (70-80 °C under solvent-free condition in excellent yields in addition this protocol can be used for industrial scales. This method offers some advantages in term of clean reaction conditions, easy work-up procedure, short reaction time, applied to convert α-diketones to α-diketoximes (as longer than other carbonyl compounds, α,β-unsaturated aldehydes and ketones to corresponding oximes and suppression of any side product. So we think that NH2OH•HCl/SiO2@FeSO4 nano composite system could be considered a new and useful addition to the present methodologies in this area. Structure of products and nano composite elucidation was carried out by 1H NMR, 13C NMR, FT-IR, scanning electron microscopy (SEM.

Effect of gamma radiation dose and sensitizer on the physical properties of irradiated natural rubber latex

International Nuclear Information System (INIS)

Komgrit, R.; Thawat, C.; B, Tripob; Wirach, T.

2009-07-01

Full text: The vulcanization of natural rubber latex can be induced by gamma radiation, which enhances cross-linking within the rubber matrix. The purpose of this research is to investigate the effect of gamma radiation dose and sensitizers on the physical properties of irradiated natural rubber. Three sensitizers n-butyl acrylate (n-B A), tetrachloroethylene (C 2 Cl 4 ) and trichloromethane (CHCl 3 ) were mixed with natural rubber latex before irradiation with gamma ray dose varied from 14 to 22 kGy. Results showed that the mixture of three sensitizers with specific ratios effectively induced the cross-linking of natural rubber latex. The cross-linking ratio and improved physical properties increased with increasing gamma dose. Therefore, the mixture ratios of n-B A, C 2 Cl 4 and CHCl 3 have shown to be a critical parameter in the vulcanization of natural rubber latex by gamma radiation

Use of rubber crumb for preparation of asphalt-concrete mixtures

Directory of Open Access Journals (Sweden)

Yerbol Tileuberdi

2012-03-01

Full Text Available In this article use of rubber crumb from spent tire for preparation of rubber-bitumen compounds is investigated. Then the rubber-bitumen compositions are used in composition of asphalt concrete mixes .

In situ reactive compatibilization of natural rubber/acrylic-bentonite composites via peroxide-induced vulcanization

International Nuclear Information System (INIS)

Fu, Lihua; Lei, Zhiwen; Xu, Chuanhui; Chen, Yukun

2016-01-01

To achieve good interfacial interaction between fillers and rubber matrix is always a hot topic in rubber reinforcing industry. In this paper, acid activated bentonite (Bt) was alkalified to be alkaline calcium-bentonite (ACBt), then acrylic acid (AA) was employed to modify ACBt to obtain acrylic-bentonite (ABt). The results of Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) illustrated that acrylate groups were chemically boned onto the surface of Bt and the layer spacing of Bt was increased. During peroxide-induced vulcanization, in situ compatibilization of ABt was realized via the reaction between the unsaturated bonds of acrylate groups on the surface of Bt and the natural rubber (NR) chains. This resulted in an enhanced cross-linked network which contributed to the improved mechanical properties of NR/ABt composites. - Highlights: • Acrylate groups were chemically boned onto the surface of bentonite. • In situ compatibilization was realized via the reaction of acrylate group and NR. • ABt particles participated in forming the NR crosslink network. • A potential reinforcing material options for “white” rubber products.

In situ reactive compatibilization of natural rubber/acrylic-bentonite composites via peroxide-induced vulcanization

Energy Technology Data Exchange (ETDEWEB)

Fu, Lihua; Lei, Zhiwen [Guangxi Key Laboratory of Petrochemical Resource Processing and Process Intensification Technology, School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Xu, Chuanhui, E-mail: xuhuiyee@gxu.edu.cn [Guangxi Key Laboratory of Petrochemical Resource Processing and Process Intensification Technology, School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Chen, Yukun, E-mail: cyk@scut.edu.cn [The Key Laboratory of Polymer Processing Engineering, Ministry of Education, China(South China University of Technology), Guangzhou, 510640 (China)

2016-02-15

To achieve good interfacial interaction between fillers and rubber matrix is always a hot topic in rubber reinforcing industry. In this paper, acid activated bentonite (Bt) was alkalified to be alkaline calcium-bentonite (ACBt), then acrylic acid (AA) was employed to modify ACBt to obtain acrylic-bentonite (ABt). The results of Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) illustrated that acrylate groups were chemically boned onto the surface of Bt and the layer spacing of Bt was increased. During peroxide-induced vulcanization, in situ compatibilization of ABt was realized via the reaction between the unsaturated bonds of acrylate groups on the surface of Bt and the natural rubber (NR) chains. This resulted in an enhanced cross-linked network which contributed to the improved mechanical properties of NR/ABt composites. - Highlights: • Acrylate groups were chemically boned onto the surface of bentonite. • In situ compatibilization was realized via the reaction of acrylate group and NR. • ABt particles participated in forming the NR crosslink network. • A potential reinforcing material options for “white” rubber products.

Properties of rubber blends based on natural rubber loaded with different fillers and cured by gamma radiation

International Nuclear Information System (INIS)

Mohamed, R.M.

2011-01-01

In this investigation system styrene butadiene rubber (1502 type) and natural rubber were blended in different ratios namely, NR/SBR (0/100), NR/SBR (25/75), NR/SBR (50/50), NR/SBR (75/25) and NR/SBR (100/0). All the samples were subjected to gamma irradiation dose up to 250 kGy. The improvement in the mechanical properties, physico-mechanical properties and thermal properties was followed as a function of irradiation dose and blend ratio. The SBR /NR (50/50) blend with reasonable properties were filled with 40 p hr of Hisil (highly fined silicon), HAF carbon black (high abrasion furnace), TiO 2 titanium dioxide and clay; the reinforcing ability of these fillers was found to follow the order: Hisil > HAF carbon black > Clay > TiO 2 The effect of different kinds of enhancing agents (coagent) namely: N, N- methylene di acrylamide (MDA), trimethylol propane tri methacrylate (TMPTMA) and tetramethylol - methane tetraacrylate (TMMT) on the properties of the obtained composites as a function of irradiation dose was studied. The data obtained showed that the enhancement character of the co agents follow the order: TMMT >TMPTMA > MDA >unenhanced composites. This investigation showed also the effect of gamma irradiation on improving the above mentioned properties in the presence of filler and co agents. Moreover, radiation dose at 100 kGy is sufficient enough for obtained the desired properties. The obtaining composites can be used in many industrial applications such as radio controlled model race car tires to footwear applications; the SBR component adds the toughness while the natural rubber provides superior resilience and energy return when used in footwear.

Tribological behavior of Al-WC nano-composites fabricated by ultrasonic cavitation assisted stir-cast method

Science.gov (United States)

Pal, Arpan; Poria, Suswagata; Sutradhar, Goutam; Sahoo, Prasanta

2018-03-01

In the present study, the effects of WC nano-particles content on the microstructure, hardness, wear, and friction behavior of aluminum matrix composites are investigated. Al-WC nano composites with varying wt% of WC (0, 1, 1.5, and 2) are fabricated using ultrasonic cavitation assisted stir-cast method. The microstructure of the nano-composite samples is analyzed using optical microscopy and scanning electron microscopy. Elemental composition is determined by energy dispersive x-ray analysis. Vicker’s microhardness test is performed in different locations on the composite sample surface with a load of 50 gf and 10s dwell time. Wear and friction of the composites under dry sliding is studied using a pin-on-disk tribotester for varying normal load (10–40 N) and sliding speed (0.1–0.4 m/s). Uniform distribution of nano-WC is observed over composite surface without noticeable clustering. Reinforcement of nano-WC particles improves wear resistance and frictional behavior of the composite. Hardness is seen to increase with increase in wt% of nano-particles. Wear behavior of composites depends on formation of layers over the surface mixed with oxidized debris and counter-face particles. Wear mechanism changes from adhesion to abrasion with increase in wt% of hard nano particles.

A Review on Potentiality of Nano Filler/Natural Fiber Filled Polymer Hybrid Composites

Directory of Open Access Journals (Sweden)

Naheed Saba

2014-08-01

Full Text Available The increasing demand for greener and biodegradable materials leading to the satisfaction of society requires a compelling towards the advancement of nano-materials science. The polymeric matrix materials with suitable and proper filler, better filler/matrix interaction together with advanced and new methods or approaches are able to develop polymeric composites which shows great prospective applications in constructions and buildings, automotive, aerospace and packaging industries. The biodegradability of the natural fibers is considered as the most important and interesting aspects of their utilization in polymeric materials. Nanocomposite shows considerable applications in different fields because of larger surface area, and greater aspect ratio, with fascinating properties. Being environmentally friendly, applications of nanocomposites offer new technology and business opportunities for several sectors, such as aerospace, automotive, electronics, and biotechnology industries. Hybrid bio-based composites that exploit the synergy between natural fibers in a nano-reinforced bio-based polymer can lead to improved properties along with maintaining environmental appeal. This review article intended to present information about diverse classes of natural fibers, nanofiller, cellulosic fiber based composite, nanocomposite, and natural fiber/nanofiller-based hybrid composite with specific concern to their applications. It will also provide summary of the emerging new aspects of nanotechnology for development of hybrid composites for the sustainable and greener environment.

Functional properties of extruded nano composites based on cassava starch, polyvinyl alcohol and montmorillonite; Propriedades funcionais de nanocompositos extrusados de amido de mandioca, alcool polivinilico e montmorilonita

Energy Technology Data Exchange (ETDEWEB)

Debiagi, Flavia; Mali, Suzana [Departamento de Bioquimica e Biotecnologia, Universidade Estadual de Londrina, PR (Brazil)

2011-07-01

The objectives of this work were to produce expanded nano composites (foams) based on starch, PVA and sodium montmorillonite and characterize them according to their expansion index (EI), density, water absorption capacity (WSC), mechanical properties and X-ray diffraction. The nano composites were prepared in a single-screw extruder using different starch contents (97.6 - 55.2 g/100 g formulation), PVA (0 - 40 g/100 g formulation), unmodified nano clay - Closite - Na (0 - 4. 8 g/100 g formulation) and glycerol (20 g/100 g formulation) as plasticizer. The addition of montmorillonite and PVA resulted in an increase of EI and a decrease of density of the samples, and reduced WSC and increased the mechanical strength of the foams. Through the analysis of X-ray diffraction can be observed that the addition of montmorillonite led to production of intercalated nano composites in all samples. (author)

Effect of graphene oxide nano filler on dynamic behaviour of GFRP composites

Science.gov (United States)

Pujar, Nagabhushan V.; Nanjundaradhya, N. V.; Sharma, Ramesh S.

2018-04-01

Nano fillers like Alumina oxide, Titanium oxide, Carbon nano tube, Nano clay have been used to improve the mechanical and damping properties of fiber reinforced polymer composites. In the recent years Graphene oxide nano filler is receiving considerable attention for its outstanding properties. Literature available shows that Graphene oxide nano filler can be used to improve the mechanical properties. The use of Graphene oxide in vibration attenuation by enhancing the passive damping in fiber reinforced polymer composite has not been fully explored. The objective of this work is to investigate the dynamic behaviour of Glass fiber-reinforced composite embedded with Graphene oxide nano filler. Graphene oxide is dispersed in epoxy resin with various concentration (0.1%, 0.5% and 1%wt) using ultra-sonification process. Composite laminates were made using the traditional hand-lay-up followed by vacuum bag process. Experimental modal analysis using traditional `strike method' is used to evaluate modal parameters using FFT analyzer and Data Acquisition System. Experiments were carried out for two different fiber orientations viz 0 ➙ & 45 ➙ and two boundary conditions (Free-Free and Cantilever). The modal parameters such as natural frequency, mode shape, damping ratio were studied. This research work demonstrates the vibration damping behaviour with incorporation of Graphene oxide and provides a basic understanding of the damping characteristics in design and manufacture of high performance composites.

Nano lead oxide and epdm composite for development of polymer based radiation shielding material: Gamma irradiation and attenuation tests

Science.gov (United States)

Özdemir, T.; Güngör, A.; Akbay, I. K.; Uzun, H.; Babucçuoglu, Y.

2018-03-01

It is important to have a shielding material that is not easily breaking in order to have a robust product that guarantee the radiation protection of the patients and radiation workers especially during the medical exposure. In this study, nano sized lead oxide (PbO) particles were used, for the first time, to obtain an elastomeric composite material in which lead oxide nanoparticles, after the surface modification with silane binding agent, was used as functional material for radiation shielding. In addition, the composite material including 1%, 5%, 10%, 15% and 20% weight percent nano sized lead oxide was irradiated with doses of 81, 100 and 120 kGy up to an irradiation period of 248 days in a gamma ray source with an initial dose rate of 21.1 Gy/h. Mechanical, thermal properties of the irradiated materials were investigated using DSC, DMA, TGA and tensile testing and modifications in thermal and mechanical properties of the nano lead oxide containing composite material via gamma irradiation were reported. Moreover, effect of bismuth-III oxide addition on radiation attenuation of the composite material was investigated. Nano lead oxide and bismuth-III oxide particles were mixed with different weight ratios. Attenuation tests have been conducted to determine lead equivalent values for the developed composite material. Lead equivalent thickness values from 0.07 to 0.65 (2-6 mm sample thickness) were obtained.

Reactivity of sulfide-containing silane toward boehmite and in situ modified rubber/boehmite composites by the silane

Science.gov (United States)

Lin, Tengfei; Zhu, Lixin; Chen, Weiwei; Wu, Siwu; Guo, Baochun; Jia, Demin

2013-09-01

The silanization reaction between boehmite (BM) nanoplatelets and bis-[3-(triethoxysilyl)-propyl]-tetrasulfide (TESPT) was characterized in detail. Via such modification process, the grafted sulfide moieties on the BM endow reactivity toward rubber and substantially improved hydrophobicity for BM. Accordingly, TESPT was employed as in situ modifier for the nitrile rubber (NBR)/BM compounds to improve the mechanical properties of the reinforced vulcanizates. The effects of BM content and in situ modification on the mechanical properties, curing characteristics and morphology were investigated. BM was found to be effective in improving the mechanical performance of NBR vulcanizates. The NBR/BM composites could be further strengthened by the incorporation of TESPT. The interfacial adhesion of NBR/BM composites was obviously improved by the addition of TESPT. The substantially improved mechanical performance was correlated to the interfacial reaction and the improved dispersion of BM in rubber matrix.

LDPE/HDPE/Clay Nano composites: Effects of Compatibilizer on the Structure and Dielectric Response

International Nuclear Information System (INIS)

David, Z.E.; Ngo, A.D.

2013-01-01

PE/clay nano composites were prepared by mixing a commercially available premixed polyethylene/O-MMT master batch into a polyethylene blend matrix containing 80 wt% low-density polyethylene and 20 wt% high-density polyethylene with and without anhydride modified polyethylene (PE-MA) as the compatibilizer using a corotating twin-screw extruder. In this study, the effect of nano clay and compatibilizer on the structure and dielectric response of PE/clay nano composites has been investigated. The microstructure of PE/clay nano composites was characterized using wide-angle X-ray diffraction (WAXD) and a scanning electron microscope (SEM). Thermal properties were examined using differential scanning calorimetry (DSC). The dielectric response of neat PE was compared with that of PE/clay nano composite with and without the compatibilizer. The XRD and SEM results showed that the PE/O-MMT nano composite with the PE-MA compatibilizer was better dispersed. In the nano composite materials, two relaxation modes are detected in the dielectric losses. The first relaxation is due to a Maxwell-Wagner-Sillars interfacial polarization, and the second relaxation can be related to dipolar polarization. A relationship between the degree of dispersion and the relaxation rate f m ax of Maxwell-Wagner-Sillars was found and discussed.

Nano-Reinforcement of Interfaces in Prepreg-Based Composites Using a Carbon Nanotubes Spraying Method

KAUST Repository

Almuhammadi, Khaled

2012-11-01

Multi-scale reinforcement of composite materials is a topic a great interest owing to the several advantages provided, e.g. increased stiffness, improved aging resistance, and fracture toughness. It is well known, that the fracture toughness of epoxy resins used as matrix materials for CFRP composites can be increased by the addition of nano-sized fillers such as Carbon nanotubes (CNTs). CNTs are particularly well suited for this purpose because of their nano-scale diameter and high aspect ratio which allow enhancing the contact area and adhesion to the epoxy matrix. On the other hand, CNTs can also be used to improve the interlaminar strength of composite, which is the resistance offered to delamination. Several fabrication techniques have been devised to this purpose, such as powder dispersion [51-53], spraying [54], roll coating [2] and electrospinning [55, 56]. The aim of this work is to extend the knowledge in this field. In particular, MWCNTs were dispersed throughout the interface of a carbon fiber composite laminate ([0o]16) through spraying and the resulting fracture toughness was investigated in detail. To this purpose, Double Cantilever Beam (DCB) specimens were fabricated by placing 0.5 wt.% CNTs at the interface of mid-plane plies and the fracture toughness was determined using the ASTM standard procedures. For comparison, baseline samples were prepared using neat prepregs. In order to corroborate the variation of fracture toughness to the modifications of interfacial damage mechanisms, Scanning Electron Microscopy (SEM) of the failed surfaces was also undertaken. The results of this work have shown that functionalized MWCNTs can enhance the interlaminar fracture toughness; indeed, compared to the neat case, an average increase around 17% was observed. The SEM analysis revealed that the improved fracture toughness was related to the ability of the Nano-reinforcement to spread the damage through crack bridging, i.e. CNTs pull-out and peeling.

The influence of radiolytic sensitizers in natural rubber latex vulcanization induced by ionizing radiation

International Nuclear Information System (INIS)

Guedes, S.M.L.; Souza, A. de

1991-01-01

This work made on radiation vulcanization of natural rubber latex process by gamma rays from 60 Co source and electron beam of 1.5 MeV, 25 m A by Dynamitron, instead of classic process using sulfur. The experiment was carried out to study the influence of sensitizers (C Cl 4 and n-butyl acrylate) and was reported the vulcanization dose for each sensitizers, related to maximum tensile strength. The results show the possibility to introduce the volatile sensitizer (n-butyl acrylate) instead of C Cl 4 (toxic) in industry applications. (author)

Improvement of mechanical and thermal properties of high energy electron beam irradiated HDPE/hydroxyapatite nano-composite

Science.gov (United States)

Mohammadi, M.; Ziaie, F.; Majdabadi, A.; Akhavan, A.; Shafaei, M.

2017-01-01

In this research work, the nano-composites of high density polyethylene/hydroxyapatite samples were manufactured via two methods: In the first method, the granules of high density polyethylene and nano-structure hydroxyapatite were processed in an internal mixer to prepare the nano-composite samples with a different weight percentage of the reinforcement phase. As for the second one, high density polyethylene was prepared in nano-powder form in boiling xylene. During this procedure, the hydroxyapatite nano-powder was added with different weight percentages to the solvent to obtain the nano-composite. In both of the procedures, the used hydroxyapatite nano-powder was synthesized via hydrolysis methods. The samples were irradiated under 10 MeV electron beam in 70-200 kGy of doses. Mechanical, thermal and morphological properties of the samples were investigated and compared. The results demonstrate that the nano-composites which we have prepared using nano-polyethylene, show better mechanical and thermal properties than the composites prepared from normal polyethylene granules, due to the better dispersion of nano-particles in the polymer matrix.

Composite Piezoelectric Rubber Band for Energy Harvesting from Breathing and Limb Motion

International Nuclear Information System (INIS)

Wang, Jhih-Jhe; Su, Huan-Jan; Hsu, Chang-I; Su, Yu-Chuan

2014-01-01

We have successfully demonstrated the design and microfabrication of piezoelectric rubber bands and their application in energy harvesting from human motions. Composite polymeric and metallic microstructures with embedded bipolar charges are employed to realize the desired stretchability and electromechanical sensitivity. In the prototype demonstration, multilayer PDMS cellular structures coated with PTFE films and stretchable gold electrodes are fabricated and implanted with bipolar charges. The composite structures show elasticity of 300∼600 kPa and extreme piezoelectricity of d 33 >2000 pC/N and d 31 >200 pC/N. For a working volume of 2.5cm×2.5cm×0.3mm, 10% (or 2.5mm) stretch results in effective d 31 of >17000 pC/N. It is estimated that electric charge of >0.2 μC can be collected and stored per breath (or 2.5cm deformation). As such, the composite piezoelectric rubber bands (with spring constants of ∼200 N/m) can be mounted on elastic waistbands to harvest the circumferential stretch during breathing, or on pads around joints to harvest the elongation during limb motion. Furthermore, the wearable piezoelectric structures can be spread, stacked and connected to charge energy storages and power micro devices

Composite Piezoelectric Rubber Band for Energy Harvesting from Breathing and Limb Motion

Science.gov (United States)

Wang, Jhih-Jhe; Su, Huan-Jan; Hsu, Chang-I.; Su, Yu-Chuan

2014-11-01

We have successfully demonstrated the design and microfabrication of piezoelectric rubber bands and their application in energy harvesting from human motions. Composite polymeric and metallic microstructures with embedded bipolar charges are employed to realize the desired stretchability and electromechanical sensitivity. In the prototype demonstration, multilayer PDMS cellular structures coated with PTFE films and stretchable gold electrodes are fabricated and implanted with bipolar charges. The composite structures show elasticity of 300~600 kPa and extreme piezoelectricity of d33 >2000 pC/N and d31 >200 pC/N. For a working volume of 2.5cm×2.5cm×0.3mm, 10% (or 2.5mm) stretch results in effective d31 of >17000 pC/N. It is estimated that electric charge of >0.2 μC can be collected and stored per breath (or 2.5cm deformation). As such, the composite piezoelectric rubber bands (with spring constants of ~200 N/m) can be mounted on elastic waistbands to harvest the circumferential stretch during breathing, or on pads around joints to harvest the elongation during limb motion. Furthermore, the wearable piezoelectric structures can be spread, stacked and connected to charge energy storages and power micro devices.

Preparation and performance of ZnO/Polyaniline nano-composite for supercapacitor

Energy Technology Data Exchange (ETDEWEB)

Yu, S.P.; Chang, X.C.; Wang, Z.M.; Han, K.F.; Zhu, H. [Beijing Univ. of Chemical Technology, Beijing (China). School of Science

2010-07-01

Supercapacitors combine the advantages of traditional capacitors and batteries. In this study, a zinc oxide (ZnO-PANI) nano-composite material was fabricated in order to investigate its behaviour in a supercapacitor application. The ZnO nano-powder was synthesized using the sol-gel method. An inverted emulsion polymerization method was then used to prepare the ZnO/PANI nanocomposite. X-ray diffraction (XRD) analyses demonstrated that the prepared ZnO had a hexagonal structure. The ZnO/PANI composite electrode was prepared. Electrochemical impedance spectroscopy (EIS) analyses indicated that the nano-composite material functioned well as an electrode. The highest capacitance rating achieved by the electrode was 31.82 F per g. 6 refs., 4 figs.

Performance of kevlar fibre-reinforced rubber composite armour against shaped-charge jet penetration

OpenAIRE

Zu,Xu-dong; Huang,Zheng-xiang; Zhai,Wen

2015-01-01

AbstractThe protective capability of the Kevlar fibre-reinforced rubber composite armour (KFRRCA) at different obliquities is studied using depth-of-penetration experiments method against a 56 mm-diameter standard-shaped charge. Efficiency factors are calculated to evaluate the protection capability of the KFRRCA at different obliquities. Meanwhile, an X-ray experiment is used to observe the deformation, fracture, and scatter of the shaped-charge jet as it penetrates the composite armour. Fin...

Microstructure characterization of multi-phase composites and utilization of phase change materials and recycled rubbers in cementitious materials

Science.gov (United States)

Meshgin, Pania

2011-12-01

This research focuses on two important subjects: (1) Characterization of heterogeneous microstructure of multi-phase composites and the effect of microstructural features on effective properties of the material. (2) Utilizations of phase change materials and recycled rubber particles from waste tires to improve thermal properties of insulation materials used in building envelopes. Spatial pattern of multi-phase and multidimensional internal structures of most composite materials are highly random. Quantitative description of the spatial distribution should be developed based on proper statistical models, which characterize the morphological features. For a composite material with multi-phases, the volume fraction of the phases as well as the morphological parameters of the phases have very strong influences on the effective property of the composite. These morphological parameters depend on the microstructure of each phase. This study intends to include the effect of higher order morphological details of the microstructure in the composite models. The higher order statistics, called two-point correlation functions characterize various behaviors of the composite at any two points in a stochastic field. Specifically, correlation functions of mosaic patterns are used in the study for characterizing transport properties of composite materials. One of the most effective methods to improve energy efficiency of buildings is to enhance thermal properties of insulation materials. The idea of using phase change materials and recycled rubber particles such as scrap tires in insulation materials for building envelopes has been studied.

Development and evaluation of fast forming nano-composite hydrogel for ocular delivery of diclofenac.

Science.gov (United States)

Li, Xingyi; Zhang, Zhaoliang; Chen, Hao

2013-05-01

In this paper, a fast forming nano-composite hydrogel was developed for potential application in ocular drug delivery. The optical transmission (OT) as well as rheological properties of nano-composite hydrogel was characterized. The developed nano-composite hydrogel given a high diclofenac micelles loading and provided a sustained release manner of diclofenac within 6h. The developed nano-composite hydrogel formulation was administrated into the eye as flowable solution, quickly forming a hydrogel that is able to resist of the blinking and flushing of tear, yet resulting in the prolonged residence time of pre-corneal. In vivo eye irritation test suggested that the developed nano-composite hydrogel was none-eye irritation might be suitable for various ocular applications. In vivo pharmacokinetic study indicated that the developed nano-composite hydrogel could significantly increase the bioavailability of diclofenac and maintain the concentration of diclofenac in aqueous humor above MEC at least 24h after administration as compared with that of the commercial diclofenac sodium eye drops, which might be able to reduce the frequency of administration for patients. Copyright © 2013 Elsevier B.V. All rights reserved.

Seawater Durability of Nano-Montmorillonite Modified Single-Lap Joining Epoxy Composite Laminates

OpenAIRE

ULUS, Hasan; KAYBAL, Halil Burak; DEMİR, Okan; TATAR, Ahmet Caner; SENYURT, Muhammed Ali; AVCI, Ahmet

2018-01-01

The objective of this study was to investigate of nano-montmorillonite modified epoxy composite single-lap bonded joints, after being exposed to seawater immersion in order to understand the effect of seawater environment on their performance. To prepare the nano adhesives, nano montmorillonite (2 wt %) was incorporated into epoxy resin. Composite bonded specimens which manufactured with VARIM (Vacuum Assisted Resin Infusion Method) were prepared accordance with ASTM D5868-01 and immersed in ...

Facile synthesis of nano cauliflower and nano broccoli like hierarchical superhydrophobic composite coating using PVDF/carbon soot particles via gelation technique.

Science.gov (United States)

Sahoo, Bichitra Nanda; Balasubramanian, Kandasubramanian

2014-12-15

We have elucidated a cost effective fabrication technique to produce superhydrophobic polyvinylidene fluoride (PVDF/DMF/candle soot particle and PVDF/DMF/camphor soot particle composite) porous materials. The water repellent dry composite was formed by the interaction of non-solvent (methanol) into PVDF/carbon soot particles suspension in N,N-dimethylformamide (DMF). It is seen that longer quenching time effectively changes the surface morphology of dry composites. The nano broccoli like hierarchical microstructure with micro or nano scaled roughen surface was obtained for PVDF/DMF/camphor soot particle, which reveals water contact angle of 172° with roll off angle of 2°. However, composite coating of PVDF/DMF/candle soot particle shows nano cauliflower like hierarchical, which illustrates water contact angle of 169° with roll off angle of 3°. To elucidate the enhancement of water repellent property of PVDF composites, we further divulge the evolution mechanism of nano cauliflower and nano broccoli structure. In order to evaluate the water contact angle of PVDF composites, surface diffusion of water inside the pores is investigated. Furthermore, the addition of small amount of carbon soot particles in composite not only provides the crystallization of PVDF, but also leads to dramatical amendment of surface morphology which increases the surface texture and roughness for superhydrophobicity. Copyright © 2014 Elsevier Inc. All rights reserved.

Development of an efficient process for radiation vulcanization of natural rubber latex using hydroperoxide with sensitizer

International Nuclear Information System (INIS)

Siri-upathum, C.; Sonsuk, M.

1996-01-01

An attempt was made to reduce irradiation dose for radiation vulcanization of natural rubber latex. A promising method was to partially crosslink the latex by radiation vulcanization using n-butyl acrylate (n-BA) as sensitizer and t-butyl hydroperoxide (BHPO) as a co-sensitizer followed by redox vulcanization using residual BHPO as an oxidant and either fructose or tetra ethylene penta mine as reducing agents. It was found that the irradiation dose was reduced to 4 kGy with 5 phr n-BA as sensitizer and 0.1 phr BHPO as co-sensitizer. Successive crosslinking to full vulcanization was done by redox vulcanization using either 4 phr fructose at 60 degree C for 3 hours of 0.4 phr tetra-ethylene penta mine at room temperature for 1 hour. The rubber films obtained had tensile strength of about 25 MPa, modulus 300% of 0.9 MPa and crosslink density of about 1.5 x 10 19 crosslink/cm 3 . It was noted that the rubber film from the co-vulcanization was the average value of the values obtained by radiation vulcanization and redox vulcanization

Rheological Properties of Rubber Compounds with Finely Divided Carbon Additives

Science.gov (United States)

Shashok, Zh. S.; Prokopchuk, N. R.; Vishnevskii, K. V.; Krauklis, A. V.; Borisevich, K. O.; Borisevich, I. O.

2018-01-01

A study has been made of the influence of three different nanomaterials: of the starting material, and also of those functionalized by amine and oxygen-containing groups, on the properties of elastomer compositions based on rubbers for special purposes. As the elastomer matrix, use was made in one case of a rubber compound based on BNKS-18 butadiene-nitrile rubber and in the other, of a combination of two grades of butadiene-nitrile rubber (BNKS-18 + BNKS-28 in a 50:50 ratio), which differed by the amount of the bound nitrile of acrylic acid. To determine the degree of interaction between the additives and the elastomer matrix, the authors carried out multiple tests of the rubber compounds. The indices of plastoelastic properties of the rubber compounds and the qualitative characteristics of distribution of the filler (elastic modulus at small deformation amplitudes and the shear modulus under large deformation) and the difference in these indices (complex dynamic modulus) alike have been determined.

Stimuli-responsive cement-reinforced rubber.

Science.gov (United States)

Musso, Simone; Robisson, Agathe; Maheshwar, Sudeep; Ulm, Franz-Josef

2014-05-14

In this work, we report the successful development of a cement-rubber reactive composite with reversible mechanical properties. Initially, the composite behaves like rubber containing inert filler, but when exposed to water, it increases in volume and reaches a stiffness that is intermediate between that of hydrogenated nitrile butadiene rubber (HNBR) and hydrated cement, while maintaining a relatively large ductility characteristic of rubber. After drying, the modulus increases even further up to 400 MPa. Wet/drying cycles prove that the elastic modulus can reversibly change between 150 and 400 MPa. Utilizing attenuated total reflection Fourier transform infrared spectroscopy), we demonstrate that the high pH produced by the hydration of cement triggers the hydrolysis of the rubber nitrile groups into carboxylate anions. Thus, the salt bridges, generated between the carboxylate anions of the elastomer and the cations of the filler, are responsible for the reversible variations in volume and elastic modulus of the composite as a consequence of environmental moisture exposure. These results reveal that cement nanoparticles can successfully be used to accomplish a twofold task: (a) achieve an original postpolymerization modification that allows one to work with carboxylate HNBR (HXNBR) not obtained by direct copolymerization of carboxylate monomers with butadiene, and (b) synthesize a stimuli-responsive polymeric composite. This new type of material, having an ideal behavior for sealing application, could be used as an alternative to cement for oil field zonal isolation applications.

Mechanical properties of the weld line defect in micro injection molding for various nano filled polypropylene composites

International Nuclear Information System (INIS)

Xie Lei; Ziegmann, Gerhard

2011-01-01

Research highlights: → PP/CNFs and PP/TiO 2 composites with relative high loading fractions (10, 20, 30 and 35 wt%) were fabricated by inner melt mixing process. Micro tensile test samples were formed by injection molding combined with variotherm process for all composites. → The morphological properties of all nano composites were characterized by WXRD, whose results imply the adding nano fillers did not change the crystal form of PP, but the crystallites size and distance between lattices of crystals were changed with various nano fillers and loading fractions. → DSC analysis show that due to the nucleating function of nano fillers, the peak temperature of crystallization was increased and the peak temperature of crystallization melting was decreased by adding the nanofillers. → The flow ability of nano composites was tested by high pressure single capillary rheometer and the results demonstrate that nano fillers increased the viscosity of PP matrix. → Based on these significant information and analysis foundation of the nano filled composites, the micro weld line samples were formed by injection molding process and characterized by tensile test method. From the achieved results, it can be found that in general, for functional nano filled polymer composites, the mechanical property of micro weld lines were obviously influenced by nano fillers' shape and loading fractions. → The E modulus of micro weld line was increased due to loading CNFs in PP matrix, while the elongation of the micro tensile samples with weld line is considerably decreased comparing with those of unfilled PP samples. The detrimental tensile strength of micro weld lines were observed when CNFs contents increasing, except for at a 10 wt%. → For TiO 2 nano particles filled PP, due to the poor dispersion of nano particles, at low loading fraction of 10 wt%, the E modulus and tensile strength of micro weld lines were decreased by filling nano particles, but when the loading fraction

Plasma-modified graphene nanoplatelets and multiwalled carbon nanotubes as fillers for advanced rubber composites

International Nuclear Information System (INIS)

Sicinski, M; Gozdek, T; Bielinski, D M; Kleczewska, J; Szymanowski, H; Piatkowska, A

2015-01-01

In modern rubber industry, there still is a room for new fillers, which can improve the mechanical properties of the composites, or introduce a new function to the material. Modern fillers like carbon nanotubes or graphene nanoplatelets (GnP), are increasingly applied in advanced polymer composites technology. However, it might be hard to obtain a well dispersed system for such systems. The polymer matrix often exhibits higher surface free energy (SFE) level with the filler, which can cause problems with polymer-filler interphase adhesion. Filler particles are not wet properly by the polymer, and thus are easier to agglomerate. As a consequence, improvement in the mechanical properties is lower than expected. In this work, multi-walled carbon nanotubes (MWCNT) and GnP surface were modified with low-temperature plasma. Attempts were made to graft some functionalizing species on plasma-activated filler surface. The analysis of virgin and modified fillers’ SFE was carried out. MWCNT and GnP rubber composites were produced, and ultimately, their morphology and mechanical properties were studied. (paper)

Preparation and characterization of reduced graphene oxide/copper composites incorporated with nano-SiO2 particles

International Nuclear Information System (INIS)

Zhang, Xinjiang; Dong, Pengyu; Zhang, Benguo; Tang, Shengyang; Yang, Zirun; Chen, Yong; Yang, Wenchao

2016-01-01

Reduced graphene oxide/copper (rGO/Cu) composites incorporated with nano-SiO 2 particles were successfully fabricated using the raw materials of GO dispersion, hydrophilic nano-SiO 2 and electrolytic Cu powder. The as-prepared composites were characterized by X-ray diffraction, field-emission scanning electron microscope and energy dispersive spectroscopy. Microstructural observation of the composite powders indicated that the graphene oxide (GO) was effectively reduced by N 2 H 4 ·H 2 O addition in the composite slurry, and the nano-SiO 2 particles and rGO sheets were randomly and completely mixed with Cu particles. The as-sintered composites exhibited the small rGO agglomerations in the Cu matrix, and the more nano-SiO 2 additions led to the agglomerations increase. The mechanical property testing revealed that rGO/Cu composites with nano-SiO 2 incorporation exhibited the higher hardness and strength, compared with the rGO/Cu composite and as-cast pure Cu. However, the strengthening in the composites with higher SiO 2 content accompanied with the expense of compressive ductility. Microstructural formation and strengthening mechanism of the composites are also discussed in details. - Highlights: • Nano-SiO 2 incorporated rGO/Cu composites were successfully fabricated. • The more nano-SiO 2 additions led to the agglomerations increase in the composites. • The nano-SiO 2 incorporated composites exhibited the better hardness and strength. • The formation and strengthening mechanism of the composite was discussed in detail.

Nitrile rubber and carboxylated nitrile rubber resistance to soybean biodiesel

OpenAIRE

Felipe Nunes Linhares; Cléverson Fernandes Senra Gabriel; Ana Maria Furtado de Sousa; Marcia Christina Amorim Moreira Leite; Cristina Russi Guimarães Furtado

2018-01-01

Abstract Biodiesel has been considered a suitable substitute for petroleum diesel, but their chemical composition differs greatly. For this reason, biodiesel interacts differently than petroleum diesel with various materials, including rubbers. Therefore, the resistance of some elastomers should be thoroughly evaluated, specifically those which are commonly used in automotive industry. Nitrile rubber (NBR) is widely used to produce vehicular parts that are constantly in contact with fuels. T...

Ultra-low temperature curable nano-silver conductive adhesive for piezoelectric composite material

Science.gov (United States)

Yan, Chao; Liao, Qingwei; Zhou, Xingli; Wang, Likun; Zhong, Chao; Zhang, Di

2018-01-01

Limited by the low thermal resistance of composite material, ultra-low temperature curable conductive silver adhesive with curing temperature less than 100 °C needed urgently for the surface conduction treatment of piezoelectric composite material. An ultra-low temperature curable nano-silver conductive adhesive with high adhesion strength for the applications of piezoelectric composite material was investigated. The crystal structure of cured adhesive, SEM/EDS analysis, thermal analysis, adhesive properties and conductive properties of different content of nano-silver filler or micron-silver doping samples were studied. The results show that with 60 wt.% nano-silver filler the ultra-low temperature curable conductive silver adhesive had the relatively good conductivity as volume resistivity of 2.37 × 10-4 Ω cm, and good adhesion strength of 5.13 MPa. Minor micron-doping (below 15 wt.%) could improve conductivity, but would decrease other properties. The ultra-low temperature curable nano-silver conductive adhesive could successfully applied to piezoelectric composite material.

Synthesis of Boron Nano wires, Nano tubes, and Nano sheets

International Nuclear Information System (INIS)

Patel, R.B.; Chou, T.; Iqbal, Z.

2014-01-01

The synthesis of boron nano wires, nano tubes, and nano sheets using a thermal vapor deposition process is reported. This work confirms previous research and provides a new method capable of synthesizing boron nano materials. The materials were made by using various combinations of MgB 2 , Mg(BH 4 ) 2 , MCM-41, NiB, and Fe wire. Unlike previously reported methods, a nanoparticle catalyst and a silicate substrate are not required for synthesis. Two types of boron nano wires, boron nano tubes, and boron nano sheets were made. Their morphology and chemical composition were determined through the use of scanning electron microscopy, transmission electron microscopy, and electron energy loss spectroscopy. These boron-based materials have potential for electronic and hydrogen storage applications.

Performance of sand and shredded rubber tire mixture as a natural base isolator for earthquake protection

Science.gov (United States)

Bandyopadhyay, Srijit; Sengupta, Aniruddha; Reddy, G. R.

2015-12-01

The performance of a well-designed layer of sand, and composites like layer of sand mixed with shredded rubber tire (RSM) as low cost base isolators, is studied in shake table tests in the laboratory. The building foundation is modeled by a 200 mm by 200 mm and 40 mm thick rigid plexi-glass block. The block is placed in the middle of a 1m by 1m tank filled with sand. The selected base isolator is placed between the block and the sand foundation. Accelerometers are placed on top of the footing and foundation sand layer. The displacement of the footing is also measured by LVDT. The whole setup is mounted on a shake table and subjected to sinusoidal motions with varying amplitude and frequency. Sand is found to be effective only at very high amplitude (> 0.65 g) of motions. The performance of a composite consisting of sand and 50% shredded rubber tire placed under the footing is found to be most promising as a low-cost effective base isolator.

Adhesion properties of styrene-butadiene rubber (SBR/Standard Malaysian Rubber (SMR L-based adhesives in the presence of phenol formaldehyde resin

Directory of Open Access Journals (Sweden)

2007-10-01

Full Text Available The adhesion properties, i. e. viscosity, tack and peel strength of styrene-butadiene rubber (SBR/Standard Malaysian Rubber (SMR L-based pressure-sensitive adhesive was studied using phenol formaldehyde resin as the tackifying resin. Toluene was used as the solvent throughout the experiment. SBR composition in SBR/SMR L blend used was 0, 20, 40, 60, 80, 100%. Three different resin loadings, i. e. 40, 80 and 120 parts per hundred parts of rubber (phr were used in the adhesive formulation. The viscosity of adhesive was determined by a HAAKE Rotary Viscometer whereas loop tack and peel strength of paper/polyethylene terephthalate (PET film were measured using a Lloyd Adhesion Tester operating at 30 cm/min. Results indicate that the viscosity of adhesive decreases with increasing % SBR whereas loop tack passes through a maximum value at 20% SBR for all resin loadings. Except for the control sample (without resin, the peel strength shows a maximum value at 60% SBR for the three modes of peel tests. For a fixed % SBR, adhesive sample containing 40 phr phenol formaldehyde resin always exhibits the highest loop tack and peel strength, an observation which is associated to the optimum wettability of adhesive on the substrate.

Chemically designed Pt/PPy nano-composite for effective LPG gas sensor.

Science.gov (United States)

Gaikwad, Namrata; Bhanoth, Sreenu; More, Priyesh V; Jain, G H; Khanna, P K

2014-03-07

Simultaneous in situ reduction of hexachloroplatinic acid by the amine group in the pyrrole monomer and oxidation of pyrrole to form polypyrrole (PPy) was examined. The reactions were performed at various temperatures to understand the degree of reduction of platinum precursor as well as doping of polypyrrole with Pt(II) chloro-complex. Spectroscopic images revealed different morphologies for the Pt/PPy nano-composite prepared at various temperatures. The as-prepared Pt/PPy nano-composite samples were tested for their ability to sense liquefied petroleum gas (LPG) which resulted in excellent sensing at relatively low temperature. The porous nature and ohmic contact between the PPy and platinum nanoparticles makes the as-prepared Pt/PPy nano-composite highly useful for sensors as well as electronic applications.

Fretting and wear behaviors of Ni/nano-WC composite coatings in dry and wet conditions

International Nuclear Information System (INIS)

Benea, Lidia; Başa, Sorin-Bogdan; Dănăilă, Eliza; Caron, Nadège; Raquet, Olivier; Ponthiaux, Pierre; Celis, Jean-Pierre

2015-01-01

Highlights: • The friction and wear properties of Ni/nano-WC composite were studied. • Nano-WC reinforcement decreased friction coefficient in dry and wet conditions. • Nano-WC reinforcement fraction was seen to be 12 wt.%. • Nanohardness increased by 27% compared to nickel without WC reinforcements. • Ennoblement of OCP corresponding to the Ni/nano-WC composite coating. - Abstract: The fretting and wear behaviors of Ni/nano-WC composite coatings were studied by considering the effect of fretting frequency of 1 Hz during 10,000 cycles, at different applied loads in dry or wet conditions. The studies were performed on a ball-on-disk tribometer and the results were compared with pure Ni coating. The nanohardness of pure Ni and Ni/nano-WC composite coatings was tested by nanoindentation technique. To evaluate the wet wear (tribocorrosion) behavior the open circuit potential (OCP) was measured before, during and after the fretting tests at room temperature in the solution that simulates the primary water circuit of Pressurized Water Reactors (PWRs). The results show that Ni/nano-WC composite coatings exhibited a low friction coefficient, high nanohardness and wear resistance compared with pure Ni coatings under similar experimental conditions. Ni/nano-WC composite coatings were obtained on stainless steel support by electrochemical codeposition of nano-sized WC particles (diameter size of ∼60 nm) with nickel, from a standard nickel Watts plating bath. The surface morphology and the composition of the coatings were characterized by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDX) respectively

Improving the performance of cement-based composites containing superabsorbent polymers by utilization of nano-SiO2 particles

International Nuclear Information System (INIS)

Pourjavadi, Ali; Fakoorpoor, Seyed Mahmoud; Khaloo, Alireza; Hosseini, Payam

2012-01-01

Highlights: ► Nano-SiO 2 fully compensates compressive but not flexural strength. ► Nano-SiO 2 has the major contribution both to yield stress and viscosity. ► Lower dosages of SAP could reduce viscosity and yield stress of pastes. -- Abstract: The application of superabsorbent polymer (SAP) as an internal curing agent for cement based composites results in benefits such as reduced autogenous shrinkage and cracking. However, a reduction in compressive and flexural strength usually occurs due to the empty voids remained in the matrix after deswelling of SAP particles. Nanoparticles are good candidates for improving the mechanical performance of cementitious materials, due to their multiple mechanisms of action, not the least their high pozzolanic activity. In the present work, the capability of amorphous nano-SiO 2 (NS) as the most widely used nanoparticle in cementitious materials, for retrieving mechanical properties of SAP-containing pastes was evaluated, and its impact on setting time and rheological properties was measured. It was found that small dosages of NS could offset the negative effect of SAP on compressive strength but flexural strength was not fully compensated. Optimization of the dosages of NS and SAP could reduce the negative influences on the yield stress and viscosity whilst improving mechanical performance. Scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy were used to monitor the changes in microstructure and composition.

Selection tests of rubber coatings for the purpose of washing towers and other components in flue gas desulfurization installations. Selectietesten van rubberdeklagen ten behoeve van wastorens en andere componenten in rookgasontzwavelingsinstallaties; Deel 1

Energy Technology Data Exchange (ETDEWEB)

Schipper, B.A.; Van Manen, J. (KEMA Inspecties en Materialen, Arnhem (Netherlands))

1993-01-01

It has appeared that the service life of chloroprene-based rubber coatings in flue gas desulfurization (FGD) installations in coal-fired power plants in the Netherlands is short. A number of rubber coating types, applied in washing towers, pipelines, pumps and boilers of FGD installations, is tested on a laboratory scale. Use has been made of the KEMA-developed accelerated test method, the Delta-T-Tube Test. In this test a rubber foil is attached to the outside of a tube. The tube is internally cooled and the outside is exposed to a test medium. Also use has been made of the KEMA-FGD test facility to expose the pipes in the washing tank and in the flue gas canal. Plates, coated with a rubber foil, are tested in so-called Atlas cells. The tubes and the plates were controlled for blister and crack formation and for erosion. Thermal analyses methods and mechanical tests were carried out to characterize the plates and the tubes before and after the exposures. It is concluded that butyl-based rubbers show better results than chloroprene-based rubbers

Super Lightweight, Metal Rubber Fabric for Extreme Space Environments, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — NanoSonic has fabricated revolutionary nanostructured, yet macroscale, multifunctional Metal RubberTM films via layer-by-layer, molecular self-assembly, which...

Characterization of nano-composite PVD coatings for wear-resistant applications

NARCIS (Netherlands)

Galvan, D.; Pei, Y.T.; de Hosson, J.T.M.; DeHosson, JTM; Brebbia, CA; Nishida, SI

2005-01-01

Various methodologies for the characterization of nano-composite coatings are discussed, which consist TiC nano-particles distributed in an amorphous hydrocarbon (a-C:H) matrix. Complications that arise from the influence of coating roughness and underlying substrate on the properties are evaluated

Evaluating Weathering of Food Packaging Polyethylene-Nano-clay Composites: Release of Nanoparticles and their Impacts.

Science.gov (United States)

Han, Changseok; Zhao, Amy; Varughese, Eunice; Sahle-Demessie, E

2018-01-01

Nano-fillers are increasingly incorporated into polymeric materials to improve the mechanical, barrier or other matrix properties of nanocomposites used for consumer and industrial applications. However, over the life cycle, these nanocomposites could degrade due to exposure to environmental conditions, resulting in the release of embedded nanomaterials from the polymer matrix into the environment. This paper presents a rigorous study on the degradation and the release of nanomaterials from food packaging composites. Films of nano-clay-loaded low-density polyethylene (LDPE) composite for food packaging applications were prepared with the spherilene technology and exposed to accelerated weathering of ultraviolet (UV) irradiation or low concentration of ozone at 40 °C. The changes in the structural, surface morphology, chemical and physical properties of the films during accelerated weathering were investigated. Qualitative and quantitative changes in properties of pristine and aged materials and the release of nano-clay proceeded slowly until 130 hr irradiation and then accelerated afterward resulting complete degradation. Although nano-clay increased the stability of LDPE and improved thermal and barrier properties, they accelerated the UV oxidation of LDPE. With increasing exposure to UV, the surface roughness, chemiluminescence index, and carbonyl index of the samples increased while decreasing the intensity of the wide-angle X-ray diffraction pattern. Nano-clay particles with sizes ranging from 2-8 nm were released from UV and ozone weathered composite. The concentrations of released nanoparticles increased with an increase in aging time. Various toxicity tests, including reactive oxygen species generation and cell activity/viability were also performed on the released nano-clay and clay polymer. The released nano-clays basically did not show toxicity. Our combined results demonstrated the degradation properties of nano-clay particle-embedded LDPE composites

Studies on structural properties of clay magnesium ferrite nano composite

Energy Technology Data Exchange (ETDEWEB)

Kaur, Manpreet, E-mail: manpreetchem@pau.edu; Singh, Mandeep [Department of Chemistry, Punjab Agricultural University, Ludhiana-141004 (India); Jeet, Kiran, E-mail: kiranjeet@pau.edu; Kaur, Rajdeep [Electron Microscopy and Nanoscience Laboratory, Punjab Agricultural University, Ludhiana-141004 (India)

2015-08-28

Magnesium ferrite-bentonite clay composite was prepared by sol-gel combustion method employing citric acid as complexing agent and fuel. The effect of clay on the structural properties was studied with X-ray diffraction (XRD), Fourier transform infrared (FT-IR) Spectroscopy, Scanning electron microscopy (SEM), SEM- Energy dispersive Spectroscope (EDS) and BET surface area analyzer. Decrease in particle size and density was observed on addition of bentonite clay. The BET surface area of nano composite containing just 5 percent clay was 74.86 m{sup 2}/g. Whereas porosity increased from 40.5 per cent for the pure magnesium ferrite to 81.0 percent in the composite showing that nano-composite has potential application as an adsorbent.

The Effect of Size and Crumb Rubber Composition as a Filler with Compatibilizer Pp-G-Ma in Polypropylene Blends and Sir-20 Compound on Mechanical and Thermal Properties

Directory of Open Access Journals (Sweden)

Erna Frida

2013-04-01

Full Text Available Having been researched the development of thermoplastic elastomer material of polypropylene and natural rubber SIR-20 compound with Crumb Rubber as the filler. Reinforced polypropylene with size 60 mesh with 1 mm, and the composition of the Crumb rubber (30, 40, and 50 wt%. Observed mechanical properties are tensile strength, fracture elongation, Young's modulus, tear strength and impact strength. Thermal properties are analyzed by DSC and DTA/TGA. It is acquired that for the size of 60 mesh crumb rubber tensile strength, fracture elongation, Young’s modulus, tear strength and impact strength are bigger than 1mm size. The addition of 60 mesh crumb rubber increases but it decreases by adding of 50 weight%. While for crumb rubber 1 mm tensile strength, fracture elongation, tear strength and impact strength decreas. Based on analysis of DSC that the addition of crumb rubber does not make a difference boiling point significantly between samples containing crumb rubber and polypropylene Analysis TGA/DTA to an increase in enthalpy and decomposition temperature with the addition of crumb rubber used and thermal stability.

Wear Resistance Properties Reinforcement Using Nano-Al/Cu Composite Coating in Sliding Bearing Maintenance.

Science.gov (United States)

Liu, Hongtao; Li, Zhixiong; Wang, Jianmei; Sheng, Chenxing; Liu, Wanli

2018-03-01

Sliding bearing maintenance is crucial for reducing the cost and extending the service life. An efficient and practical solution is to coat a restorative agent onto the worn/damaged bearings. Traditional pure-copper (Cu) coating results in a soft surface and poor abrasion resistance. To address this issue, this paper presents a nano-composite repairing coating method. A series of nano-Al/Cu coatings were prepared on the surface of 45 steel by composite electro-brush plating (EBP). Their micro-hardness was examined by a MHV-2000 Vickers hardness tester, and tribological properties by a UMT-2M Micro-friction tester, 3D profiler and SEM. Then, the influence of processing parameters such as nano-particle concentration and coating thickness on the micro-hardness of nano-Al/Cu coating was analyzed. The experimental analysis results demonstrate that, when the nano-Al particle concentration in electrolyte was 10 g/L, the micro-hardness of the composite coating was 1.1 times as much as that of pure-Cu coating. When the Al nano-particle concentration in electrolyte was 20 g/L, the micro-hardness of the composite coating reached its maximum value (i.e., 231.6 HV). Compared with the pure-Cu coating, the hardness and wear resistance of the nano-composite coating were increased, and the friction coefficient and wear volume were decreased, because of the grain strengthening and dispersion strengthening. The development in this work may provide a feasible and effective nano-composite EBP method for sliding bearing repair.

Radiation curable adhesive compositions and composite structures

International Nuclear Information System (INIS)

Brenner, W.

1984-01-01

This disclosure relates to novel adhesive compositions and composite structures utilizing the same, wherein said adhesive compositions contain an elastomer, a chemically compatible ethylenically unsaturated monomer, a tackifier, an adhesion promoter, and optionally, pigments, fillers, thickeners and flow control agents which are converted from the liquid to the solid state by exposure to high energy ionizing radiation such as electron beam. A particularly useful application for such adhesive compositions comprises the assembly of certain composite structures or laminates consisting of, for example, a fiber flocked rubber sheet and a metal base with the adhesive fulfilling the multiple functions of adhering the flocked fiber to the rubber sheet as well as adhering the rubber sheet to the metal base. Optionally, the rubber sheet itself may also be cured at the same time as the adhesive composition with all operations being carried out at ambient temperatures and in the presence of air, with exposure of said assembly to selected dosages of high energy ionizing radiation. These adhesive compositions contain no solvents thereby almost eliminating air pollution or solvent toxicity problems, and offer substantial savings in energy and labor as they are capable of curing in very short time periods without the use of external heat which might damage the substrate

Preparations and thermal properties of micro- and nano-BN dispersed HDPE composites

International Nuclear Information System (INIS)

Jung, Jinwoo; Kim, Jaewoo; Uhm, Young Rang; Jeon, Jae-Kyun; Lee, Sol; Lee, Hi Min; Rhee, Chang Kyu

2010-01-01

The thermal properties of micro-sized boron nitride (BN) and nano-sized BN dispersed high density polyethylene (HDPE) composites were investigated by means of differential scanning calorimetry (DSC) and thermo-gravimetric analysis (TGA). Nano-BN powder was prepared by using a ball mill process before it was mixed in HDPE. To enhance the dispersivity of nano-BN in the polymer matrix, the surfaces of the nano-particles were treated with low density polyethylene (LDPE) which was dissolved in the cyclohexane solvent. The average particle sizes of micro-BN powder and LDPE coated nano-BN powder were ∼10 μm and ∼100 nm respectively. Dispersion and distribution of 5 wt% and 20 wt% of micro-BN and nano-BN respectively mixed in HDPE were observed by using the scanning electron microscope (SEM). According to the thermal analyses of pure HDPE, micro-BN/HDPE, and nano-BN/HDPE, 20 wt% nano-BN/HDPE composite shows the lowest enthalpy of fusion (ΔH m ) and better thermal conductive characteristics compared to the others.

Nano-hydroxyapatite/poly ε-caprolactone composite 3D scaffolds for mastoid obliteration

International Nuclear Information System (INIS)

Kim, S E; Yun, H S; Hyun, Y T; Shin, J W; Song, J J

2009-01-01

The aim of this study is to evaluate the use of our nano-HA/PCL composite 3D scaffolds as graft materials for mastoid cavity obliteration in an animal model. Nano-HA particles were synthesized by chemical precipitation technique and mixed them with PCL solution to make composite paste. 3D scaffolds were fabricated by a paste extruding deposition process. The nano-HA/PCL 3D scaffolds showed good in vivo bone regeneration behaviour in a rabbit model after 4 and 8 week implantation. To characterize the 3D scaffolds as a grafting material for mastoid obliteration, mastoid cavities were introduced in rats and implanted the scaffolds. After two week implantation, histological examination showed good tissue ingrowth and new bone formation behaviour. It can be argued that our nano-HA/PCL composite 3D scaffold is a promising alternative material for mastoid obliteration.

Multifunctional, Nanostructured Metal Rubber Protective Films for Space Exploration, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — NanoSonic has developed revolutionary nanostructured, yet macroscale, multifunctional Metal RubberTM films. In support of NASA's Vision for Space Exploration, low...

Multifunctional, Nanostructured Metal Rubber Protective Films for Space Exploration, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — NanoSonic has developed revolutionary nanostructured, yet macroscale, multifunctional Metal RubberTM films. In support of NASA's Vision for Space Exploration, low...

Radiation Processing of Active Biodegradable Green Nano Composite Materials for Packaging Purposes

Energy Technology Data Exchange (ETDEWEB)

AbdEl-Rehim, Hassan A.; Hegazy, El-Sayed A.; Raafat, Ahmed [National Center for Radiation Research and Technology NCRRT, Atomic Energy Authority, Cairo, Egypt P. O. Box 29, Nasr City, Cairo (Egypt)

2011-07-01

Clean and green reduction process of silver ions and graphene (GO) into nanosilver metal and graphene (GR) nanosheets respectively was achieved via gamma irradiation. The efficiency of gamma radiation to reduce silver ions and graphene oxide (GO) was investigated using UV-vis spectroscopy. Effects of gaseous atmosphere type, dispersion pH value, capping agent type and irradiation dose on GR nano-sheets formation were investigated. The presence of capping agent such as sodium carboxymethyl cellulose (CMC) or cellulose acetate is proven to be crucial. The obtained GR nanosheets and nanosilver metals are characterized using atomic force microscopy (AFM), transmission electron microscopy (TEM), Fourier transform infrared spectrometry (FT-IR), X-ray diffraction (XRD) as well as thermo-gravimetric analyzer (TGA) and differential scanning calorimeter (DSC). Effectiveness, simplicity, reproducibility, and low energy consumption are the merits of using the Gamma radiation technique. Furthermore, the capping agent is eco-friendly and the dispersion is stable for months at room temperature. This approach can open up large-scale production of GR nanosheets and nanosilver metals. The prepared Nano-silver can be mixed with different natural polymer like CA to form Nano-composite films. The excellent physical properties of CA did not affect by addling Ag. The ionizing radiation has un-significant effect on the properties of CA-Ag nano composites films The CA-Ag nano composites posses biological activity towards different microorganisms. On other hand graphene or graphene oxide dispersions might be of interesting for producing biological active packaging films. Go as nanofillers has used for fabrication of a biocomposite with chitosan. The significantly improved in Chitosan /Go nano composites physical properties, including mechanical property, electrical conductivity, and structural stability, was demonstrated. Properties of the CA-Ag and Chitosan /Go nano composites suggest

Radiation Processing of Active Biodegradable Green Nano Composite Materials for Packaging Purposes

International Nuclear Information System (INIS)

AbdEl-Rehim, Hassan A.; Hegazy, El-Sayed A.; Raafat, Ahmed

2011-01-01

Clean and green reduction process of silver ions and graphene (GO) into nanosilver metal and graphene (GR) nanosheets respectively was achieved via gamma irradiation. The efficiency of gamma radiation to reduce silver ions and graphene oxide (GO) was investigated using UV-vis spectroscopy. Effects of gaseous atmosphere type, dispersion pH value, capping agent type and irradiation dose on GR nano-sheets formation were investigated. The presence of capping agent such as sodium carboxymethyl cellulose (CMC) or cellulose acetate is proven to be crucial. The obtained GR nanosheets and nanosilver metals are characterized using atomic force microscopy (AFM), transmission electron microscopy (TEM), Fourier transform infrared spectrometry (FT-IR), X-ray diffraction (XRD) as well as thermo-gravimetric analyzer (TGA) and differential scanning calorimeter (DSC). Effectiveness, simplicity, reproducibility, and low energy consumption are the merits of using the Gamma radiation technique. Furthermore, the capping agent is eco-friendly and the dispersion is stable for months at room temperature. This approach can open up large-scale production of GR nanosheets and nanosilver metals. The prepared Nano-silver can be mixed with different natural polymer like CA to form Nano-composite films. The excellent physical properties of CA did not affect by addling Ag. The ionizing radiation has un-significant effect on the properties of CA-Ag nano composites films The CA-Ag nano composites posses biological activity towards different microorganisms. On other hand graphene or graphene oxide dispersions might be of interesting for producing biological active packaging films. Go as nanofillers has used for fabrication of a biocomposite with chitosan. The significantly improved in Chitosan /Go nano composites physical properties, including mechanical property, electrical conductivity, and structural stability, was demonstrated. Properties of the CA-Ag and Chitosan /Go nano composites suggest

Electron beam processing of rubber wood fibers - polypropylene composites. Effects of reactive additives on the physical and mechanical properties

International Nuclear Information System (INIS)

Nor Yuziah Mohd Yunus; Jalaluddin Harun; Khairul Zaman

2000-01-01

The purpose of this study is to determine the suitability of producing agro-fiber reinforced plastic composite (agro-FRPC) from rubber wood fiber blended in polypropylene matrix. The effects of varying fiber dimension and fiber content on the physical and mechanical properties of the composite were evaluated to provide an insight into the fiber matrix adhesion. The effects of reactive additives on the physical and mechanical properties of the composite were evaluated which provides the insight on the reinforcement of the composite. Rubber wood fiber used in this study is currently being used in the manufacturing of medium density fiber (MDF) board. Two sizes of rubber wood fiber were used i.e. 0.5-1.0 mm and 1.0-2.0 mm. Homopolymer polypropylene of MFI 14.0 was used as a matrix. The irradiation work was carried out using electron beam accelerator, 3.0 MeV, 3.0 mA. Various types of reactive additives (RA) with mono-functional, di-functional, tri-functional and oligomer were applied in the blend. For comparison, a conventional chemical cross-linking using two types of maleated polypropylene, MPA (Mw=9,000) and PMAP (Mw=220,000) were also performed. (author)

Electron beam processing of rubber wood fibers - polypropylene composites. Effects of reactive additives on the physical and mechanical properties

Energy Technology Data Exchange (ETDEWEB)

Nor Yuziah Mohd Yunus; Jalaluddin Harun [Universiti Putra Malaysia, Selangor Darul Ehsan (Malaysia); Khairul Zaman [Malaysian Institute for Nuclear Technology Research (MINT), Selangor Darul Ehsan (Malaysia)

2000-07-01

The purpose of this study is to determine the suitability of producing agro-fiber reinforced plastic composite (agro-FRPC) from rubber wood fiber blended in polypropylene matrix. The effects of varying fiber dimension and fiber content on the physical and mechanical properties of the composite were evaluated to provide an insight into the fiber matrix adhesion. The effects of reactive additives on the physical and mechanical properties of the composite were evaluated which provides the insight on the reinforcement of the composite. Rubber wood fiber used in this study is currently being used in the manufacturing of medium density fiber (MDF) board. Two sizes of rubber wood fiber were used i.e. 0.5-1.0 mm and 1.0-2.0 mm. Homopolymer polypropylene of MFI 14.0 was used as a matrix. The irradiation work was carried out using electron beam accelerator, 3.0 MeV, 3.0 mA. Various types of reactive additives (RA) with mono-functional, di-functional, tri-functional and oligomer were applied in the blend. For comparison, a conventional chemical cross-linking using two types of maleated polypropylene, MPA (Mw=9,000) and PMAP (Mw=220,000) were also performed. (author)

Nanosílice como carga en la RTV SR usada para cubrir aisladores; Nanosilica as filler in the Room temperature vulcanized silicone rubber used to coat insulators

Directory of Open Access Journals (Sweden)

Ignat Pérez Almirall

2014-04-01

Full Text Available En el presente trabajo se realiza un estudio sobre la influencia que tiene agregar como carga nanosílice a la goma de silicona vulcanizada a temperatura ambiente (RTV SR, por sus siglas en inglés que es empleada para cubrir aisladores de vidrio o de porcelana. Con este objetivo se observó la dispersión de la nanosílice en la RTV SR por medio de microscopía electrónica de barrido (MEV, por sus siglas en inglés, se midió la permitividad de la RTV SR con y sin nanosílice para varias frecuencias y se evaluó la influencia que tiene la nanosílice en la resistencia a la erosión. Además fueron medidas las corrientes de fuga durante ensayos de niebla salina a aisladores de vidrio pintados con estos recubrimientos, analizando también la pérdida de hidrofobicidad que ocurre durante el ensayo y su recuperación una vez finalizado el mismo.  The present research work carries out a study on the influence of nanosilica on room temperature vulcanized silicone rubber (RTV SR used to coat insulators. Considering this objective, the dispersion of nanosilica was observed by means of scanning electron microscopy (MEV, the permittivity of the room temperature vulcanized silicone rubber was measured with and without nanosilica for different frequencies and the influence of nanosilica in erosion resistance. Leakage currents were also measured during salt spray tests to glass insulators covered with these coatings; the loss of hidrophobicity during the test was also measured and its recovery was analyzed the test was finished.

Nanosílice como carga en la RTV SR usada para cubrir aisladores/ Nanosilica as filler in the Room temperature vulcanized silicone rubber used to coat insulators

Directory of Open Access Journals (Sweden)

Ignat Pérez Almirall

2012-02-01

Full Text Available En el presente trabajo se realiza un estudio sobre la influencia que tiene agregar como carga nanosílice a la goma de silicona vulcanizada a temperatura ambiente (RTV SR, por sus siglas en inglés que es empleada para cubrir aisladores de vidrio o de porcelana. Con este objetivo se observó la dispersión de la nanosílice en la RTV SR por medio de microscopía electrónica de barrido (MEV, por sus siglas en inglés, se midió la permitividad de la RTV SR con y sin nanosílice para varias frecuencias y se evaluó la influencia que tiene la nanosílice en la resistencia a la erosión. Además fueron medidas las corrientes de fuga durante ensayos de niebla salina a aisladores de vidrio pintados con estos recubrimientos, analizando también la pérdida de hidrofobicidad que ocurre durante el ensayo y su recuperación una vez finalizado el mismo.The present research work carries out a study on the influence of nanosilica on room temperature vulcanized silicone rubber (RTV SR used to coat insulators. Considering this objective, the dispersion of nanosilica was observed by means of scanning electron microscopy (MEV, the permittivity of the room temperature vulcanized silicone rubber was measured with and without nanosilica for different frequencies and the influence of nanosilica in erosion resistance. Leakage currents were also measured during salt spray tests to glass insulators covered with these coatings; the loss of hidrophobicity during the test was also measured and its recovery was analyzed the test was finished.

Morphology of Poly lactide/Polycaprolactone (PLA/PCL) Nano composite by Scanning Electron Microscopy (SEM)

International Nuclear Information System (INIS)

Siti Zulaiha Hairaldin; Wan Md Zin Wan Yunus; Norazowa Ibrahim

2011-01-01

In this study, Octadecylamine Modified Montmorillonites (ODAMMT) were used to prepare Poly lactide/ Polycaprolactone (PLA/ PCL) nano composites. PLA and PCL mix in 90:10 ratios, using an internal mixer by melt blending technique. The other sample was blend with Natrium Montmorillonite (NaMMT) and Octadecylamine Modified Montmorillonite (ODA-MMT) to produce PLA/ PCL-NaMMT and PLA/ PCL ODAMMT. To characterize the polymer nano composites, X-ray diffraction (XRD), FTIR and SEM analysis were conducted. Comparison of morphology were made up between PLA/ PCL, PLA/ PCL with presence of 7 % of Na-MMT and 7 % ODA-MMT respectively based on SEM micrograph by calculate the number-average diameter. (author)

Properties of the chalcogenide–carbon nano tubes and graphene composite materials

International Nuclear Information System (INIS)

Singh, Abhay Kumar; Kim, JunHo; Park, Jong Tae; Sangunni, K.S.

2015-01-01

Highlights: • Chalcogenides. • Melt quenched. • Composite materials. • Multi walled carbon nano tubes. • Bilayer graphene. - Abstract: Composite can deliver more than the individual elemental property of the material. Specifically chalcogenide- multi walled carbon nano tubes and chalcogenide- bilayer graphene composite materials could be interesting for the investigation, which have been less covered by the investigators. We describe micro structural properties of Se 55 Te 25 Ge 20, Se 55 Te 25 Ge 20 + 0.025% multi walled carbon nano tubes and Se 55 Te 25 Ge 20 + 0.025% bilayer graphene materials. This gives realization of the alloying constituents inclusion/or diffusion inside the multi walled carbon nano tubes and bilayer graphene under the homogeneous parent alloy configuration. Raman spectroscopy, X-ray photoelectron spectroscopy, UV/Visible spectroscopy and Fourier transmission infrared spectroscopy have also been carried out under the discussion. A considerable core energy levels peak shifts have been noticed for the composite materials by the X-ray photoelectron spectroscopy. The optical energy band gaps are measured to be varied in between 1.2 and 1.3 eV. In comparison to parent (Se 55 Te 25 Ge 20 ) alloy a higher infrared transmission has been observed for the composite materials. Subsequently, variation in physical properties has been explained on the basis of bond formation in solids

An active nano-supported interface designed from gold nanoparticles embedded on ionic liquid for depositing DNA

International Nuclear Information System (INIS)

Lu Liping; Kang Tianfang; Cheng Shuiyuan; Guo Xiurui

2009-01-01

The use of an active nano-interface designed from gold nanoparticles embedded on ionic liquid for DNA damage resulted from formalehyde (HCHO) is reported in this article. The active nano-interface was fabricated by depositing gold nanoparticles on the ionic liquid 1-butyl-3-methylimidazolium tetrafluroborate ([bmim][BF 4 ]). A glassy carbon electrode modified by this composite film was fabricated to immobilize DNA for probing into the damage resulted from HCHO. The modifying process was characterized by X-ray photoelectron spectroscopy, atomic force microscopy and electrochemistry involving electrochemical impedance spectroscopy. It was found that the modified film performs effectively in studying the DNA damage by electrocatalytic activity toward HCHO oxidation.

Development of nano-composite membranes to improve alkaline fuel cell performance

CSIR Research Space (South Africa)

Nonjola, P

2011-09-01

Full Text Available The work presented here describes modification of commercially available polysulfone (PSU) as well as the formation of nano-composite membrane i.e. TiO2 nano particles incorporated into anion exchange polymer matrix....

Action of colloidal silica films on different nano-composites

Directory of Open Access Journals (Sweden)

S. Abdalla

Full Text Available Nano-composite films have been the subject of extensive work to develop the energy-storage efficiency of electrostatic capacitors. Factors such as polymer purity, nano-particles size, and film morphology drastically affect the electrostatic efficiency of the dielectric material that form an insulating film between conductive electrodes of a capacitor. This in turn affects the energy storage performance of the capacitor. In the present work, we have studied the dielectric properties of 4 high pure amorphous polymer films: polymethylmethacrylate (PMMA, polystyrene, polyimide and poly-4-vinylpyridine. Comparison between the dielectric properties of these polymers has revealed that the higher break down performance is a character of polyimide PI and PMMA. Also, our experimental data shows that adding colloidal silica to PMMA and PI leads to a net decrease in the dielectric properties compared to the pure polymer. Keywords: Dielectric break down, Polymers, Nano-composite, Colloidal silica

Feasibility study of a soil-based rubberized CLSM.

Science.gov (United States)

Wu, Jason Y; Tsai, Mufan

2009-02-01

The development of beneficial uses of recycled scrap tires is always in great demand around the world. The disposal of on-site surplus excavated soil and the production of standard engineering aggregates have also been facing increasing environmental and ecological challenges in congested islands, such as Taiwan. This paper presents an experimental study using recycled crumb rubber and native silty sand to produce a lightweight, soil-based, rubberized controlled low strength material (CLSM) for a bridge approach repair. To assess the technical feasibility of this material, the effects of weight ratios of cement-to-water (C/W) and water-to-solid (W/S), and of rubber content on the engineering properties for different mixtures were investigated. The presented test results include flowability, unit weight, strength, settlement potential, and bearing capacity. Based on the findings, we conclude that a soil-based rubberized CLSM with 40% sand by weight and an optimal design ratio of 0.7 for C/W and 0.35 for W/S can be used for the proposed bridge approach repair. Such a mixture has demonstrated acceptable flowability, strength, and bearing capacity. Its lower unit weight, negligible compressibility, and hydrocollapse potential also help ensure that detrimental settlement is unlikely to occur. The results illustrate a novel scheme of CLSM production, and suggest a beneficial alternative for the reduction of scrap tires as well as conservation of resources and environment.

Advanced Metal Rubber Sensors for Hypersonic Decelerator Entry Systems, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — NanoSonic proposes to design and develop light-weight, low-modulus, and durable Metal Rubber™ sensors for aeroelastic analysis of Hypersonic Decelerator Entry...

Experimental and numerical characterization of scalable cellulose nano-fiber composite

Science.gov (United States)

Barari, Bamdad

Fiber-reinforced polymer composites have been used in recent years as an alternative to the conventional materials because of their low weight, high mechanical properties and low processing temperatures. Most polymer composites are traditionally made using reinforcing fibers such as carbon or glass fibers. However, there has been recent interest in making these reinforcing fibers from natural resources. The plant-derived cellulose nano-fibers (CNF) are a material with remarkable mechanical properties at the nano-scale that are much superior to the mechanical properties of the traditional natural fibers (such as jute, hemp, kenaf, etc) used in the natural-fiber based polymer composites. Because CNF is bio-based and biodegradable, it is an attractive 'green' alternative for use in automotive, aerospace, and other engineering applications. However, efforts to produce CNF based nano-composites, with successful scaling-up of the remarkable nanoscale properties of CNF, have not met with much success and form an active area of research. The main goals of this research are to characterize the scalable CNF based nano composites using experimental methods and to develop effective models for flow of polymeric resin in the CNF-based porous media used during the proposed manufacture of CNF nano-composites. In the CNF composite characterization section, scalable isotropic and anisotropic CNF composites were made from a porous CNF preforms created using a freeze drying process. Formation of the fibers during freeze-drying process can change the micro skeleton of the final preform structure as non-aligned or isotropic and aligned or anisotropic CNF. Liquid Composite Molding (LCM) processes form a set of liquid molding technologies that are used quite commonly for making the conventional polymer composites. An improvised vacuum-driven LCM process was used to make the CNF-based nanocomposites from CNF preforms using a 'green' epoxy resin with high bio-content. Under the topic of

Mechanical and microstructure of reinforced hydroxyapatite/calcium silicate nano-composites materials

International Nuclear Information System (INIS)

Beheri, Hanan H.; Mohamed, Khaled R.; El-Bassyouni, Gehan T.

2013-01-01

Highlights: ► Nano sized of HA and CS powders were prepared. ► Mechanical of HACS composites enhanced with content of CS. ► The apatite formation onto the composites is proved. -- Abstract: In this study, the nano sized hydroxyapatite (HA) and calcium silicate (CS) powders prepared by both chemical precipitation and sol–gel methods respectively. Biphasic nano-composites materials containing different ratios of HA and CS were fabricated and assessed using X-ray diffraction (XRD), Fourier transmission infrared reflectance (FT-IR), transmission electron microscopy (TEM) and scanning electron microscopy (SEM) techniques. The effect of variation of ratios between HA and CS on mechanical properties, microstructure and in vitro study was studied. The results proved that the mechanical properties were enhanced with increasing the CS ratio in the composite. In vitro study proved the formation and nucleation of apatite onto composites surfaces which contain low content of CS after one week of immersion. Finally, it is concluded that the HACS composites containing high HA content at the expense of CS content will be promising for bone substitute’s applications, especially in load bearing sites.

SeZnSb alloy and its nano tubes, graphene composites properties

Directory of Open Access Journals (Sweden)

Abhay Kumar Singh

2013-04-01

Full Text Available Composite can alter the individual element physical property, could be useful to define the specific use of the material. Therefore, work demonstrates the synthesis of a new composition Se96-Zn2-Sb2 and its composites with 0.05% multi-walled carbon nano tubes and 0.05% bilayer graphene, in the glassy form. The diffused amorphous structure of the multi walled carbon nano tubes and bilayer gaphene in the Se96-Zn2-Sb2 alloy have been analyzed by using the Raman, X-ray photoluminescence spectroscopy, Furrier transmission infrared spectra, photoluminescence, UV/visible absorption spectroscopic measurements. The diffused prime Raman bands (G and D have been appeared for the multi walled carbon nano tubes and graphene composites, while the X-ray photoluminescence core energy levels peak shifts have been observed for the composite materials. Subsequently the photoluminescence property at room temperature and a drastic enhancement (upto 80% in infrared transmission percentage has been obtained for the bilayer graphene composite, along with optical energy band gaps for these materials have been evaluated 1.37, 1.39 and 1.41 eV.

Impact of Surface Modification and Nanoparticle on Sisal Fiber Reinforced Polypropylene Nano composites

International Nuclear Information System (INIS)

Ibrahim, I. D.; Jamiru, T.; Sadiku, E. R.; Agwuncha, S. Ch.; Kupolati, W. K.

2016-01-01

The use of plant fibers, polymer, and nanoparticles for composite has gained global attention, especially in the packaging, automobile, aviation, building, and construction industries. Nano composites materials are currently in use as a replacement for traditional materials due to their superior properties, such as high strength-to-weight ratio, cost effectiveness, and environmental friendliness. Sisal fiber (SF) was treated with 5% NaOH for 2 hours at 70"°C. A mixed blend of sisal fiber and recycled polypropylene (rPP) was produced at four different fiber loadings: 10, 20, 30, and 40 wt.%, while nano clay was added at 1, 3, and 5 wt.%. Maleic anhydride grafted polypropylene (MAPP) was used as the compatibilizer for all composites prepared except the untreated sisal fibers. The characterization results showed that the fiber treatment, addition of MAPP, and nano clay improved the mechanical properties and thermal stability and reduced water absorption of the SF/rPP nano composites. The tensile strength, tensile modulus, and impact strength increased by 32.80, 37.62, and 5.48%, respectively, when compared to the untreated SF/rPP composites. Water absorption was reduced due to the treatment of fiber and the incorporation of MAPP and nano clay.

Preparation and Characterization of Water-Based Nano-fluids for Nuclear Applications

International Nuclear Information System (INIS)

Williams, W.C.; Forrest, E.; Hu, L.W.; Buongiorno, J.

2006-01-01

As part of an effort to evaluate water-based nano-fluids for nuclear applications, preparation and characterization has been performed for nano-fluids being considered for MIT's nano-fluid heat transfer experiments. Three methods of generating these nano-fluids are available: creating them from chemical precipitation, purchasing the nano-particles in powder form and mixing them with the base fluid, and direct purchase of prepared nano-fluids. Characterization of nano-fluids includes colloidal stability, size distribution, concentration, and elemental composition. Quality control of the nano-fluids to be used for heat transfer testing is crucial; an exact knowledge of the fluid constituents is essential to uncovering mechanisms responsible for heat transport enhancement. Testing indicates that nano-fluids created by mixing a liquid with nano-particles in powder form are often not stable, although some degree of stabilization is obtainable with pH control and/or surfactant addition. Some commercially available prepared nano-fluids have been found to contain unacceptable levels of impurities and/or include a different weight percent of nano-particles compared to vendor specifications. Tools utilized to characterize and qualify nano-fluids for this study include neutron activation analysis (NAA), inductively-coupled plasma spectroscopy (ICP), transmission electron microscopy (TEM) imaging, thermogravimetric analysis (TGA) and dynamic light scattering (DLS). Preparation procedures and characterization results for selected nano-fluids will be discussed in detail. (authors)

Fracture behavior of rubber powder modified rubber blends applied for conveying belt top covers

OpenAIRE

Euchler, Eric; Stocek, Radek; Gehde, Michael; Bunzel, Jörg-Michael; Saal, Wolfgang; Kipscholl, Reinhold

2016-01-01

The aim of this study is concentrated on the experimental investigation of wear resistance of rubber powder modified rubber blends. Styrene-Butadiene-Rubber (SBR) blends applied for conveying belt top covers have been modified by ground rubber (rubber powder) based on SBR. We theoretically described the rubber wear mechanism due to loading conditions occurring at conveyor belts in the field, to simulate wear behavior of top cover rubber materials. An own developed testing equipment based on g...

Radiation Resistant, Reconfigurable, Shape Memory Metal Rubber Space Arrays, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — NanoSonic has demonstrated that Shape Memory Metal RubberTM (SM-MR) adaptive skins exhibit reconfigurable and durable RF properties. It is hypothesized that such...

Stress development in particulate, nano-composite and polymeric coatings

Science.gov (United States)

Jindal, Karan

2009-12-01

The main goal of this research is to study the stress, structural and mechanical property development during the drying of particulate coatings, nano-composite coatings and VOC compliant refinish clearcoats. The results obtained during this research establish the mechanism for the stress development during drying in various coating systems. Coating stress was measured using a controlled environment stress apparatus based on cantilever deflection principle. The stress evolution in alumina coatings made of 0.4 mum size alumina particles was studied and the effect of a lateral drying was investigated. The stress does not develop until the later stages of drying. A peak stress was observed during drying and the peak stress originates due to the formation of pendular rings between the particles. Silica nanocomposite coatings were fabricated from suspension of nano sized silicon dioxide particles (20 nm) and polyvinyl alcohol (PVA) polymer. The stress in silica nano-composite goes through maximum as the amount of polymer in the coating increases. The highest final stress was found to be ˜ 110MPa at a PVA content of 60 wt%. Observations from SEM, nitrogen gas adsorption, camera imaging, and nano-indentation were also studied to correlate the coatings properties during drying to measured stress. A model VOC compliant two component (2K) acrylic-polyol refinish clearcoat was prepared to study the effects of a new additive on drying, curing, rheology and stress development at room temperature. Most of the drying of the low VOC coatings occurred before appreciable (20%) crosslinking. Tensile stress developed in the same timeframe as drying and then relaxed over a longer time scale. Model low VOC coatings prepared with the additive had higher peak stresses than those without the additive. In addition, rheological data showed that the additive resulted in greater viscosity buildup during drying.

Preparation of irradiated natural rubber latex-styrene copolymer for electrical gloves

International Nuclear Information System (INIS)

Made Sumarti Kardha

2010-01-01

Research on irradiated natural rubber latex-styrene copolymer to prepare electrical glove have been done. Vulcanization of natural rubber latex (NRL) was done by mixing 2 phr (per hundred of rubber) of normal butyl acrylate (n-BA) emulsion then irradiated with ã-ray "6"0Co at the dose of 30 kGy producing irradiated natural rubber latex (INRL). Natural rubber latex-styrene copolymers (SC) were prepared by mixing NRL and styrene monomer at styrene concentrations of 50 phr, 75 phr, 100 phr, 500 phr and irradiated at the doses of 15 kGy, 30 kGy and 45 kGy, then characterized their latex and film properties to obtain optimum SC of SC50. This optimum SC, SC50 then mixed with IRNL at the weight ratio of 0/100, 30/70, 50/50, 70/30 and 100/0, to produce irradiated natural rubber latex-styrene copolymer. The properties of copolymer rubber films made by dipping process i.e., % conversion, total solid content, latex viscosity, tensile strength, modulus 300 %, elongation at break, electrical resistance and dielectric constant were then characterized. Characterization result showed that (INRL-SC50) with 50/50 ratio irradiated at the dose of 30 kGy, have % conversion of 80.93 %, electrical resistivity of 1.73 x 10"1"4 Ohm cm and dielectric constant of 2.76 which fulfill the requirement as material for electrical gloves. (author)

Effect of nano-scaled styrene butadiene rubber based nucleating agent on the thermal, crystallization and physical properties of isotactic polypropylene

Energy Technology Data Exchange (ETDEWEB)

Petchwattana, Nawadon [Division of Polymer Materials Technology, Faculty of Agricultural Product Innovation and Technology, Srinakharinwirot University, Sukhumvit 23, Wattana, Bangkok 10110 (Thailand); Covavisaruch, Sirijutaratana, E-mail: sirijutaratana.c@chula.ac.th [Department of Chemical Engineering, Faculty of Engineering, Chulalongkorn University, Pathumwan, Bangkok 10330 (Thailand); Sripanya, Panjapong [Thai Oleochemicals Company Limited (A Subsidiary of PTT Global Chemical Public Company Limited), Mueang Rayong, Rayong 21150 (Thailand)

2014-01-05

Highlights: • The effect of a SBR based β-NA on the properties iPP was investigated. • The addition of β-NA led to higher population of nuclei and smaller spherulites. • β to α phase transformation was observed when re-extrusion process was applied. • Impact strength was increased when the β-NA was added from 0.10 to 0.20 wt%. -- Abstract: The influence of a specific nano-scaled styrene butadiene rubber based β-nucleating agent (β-NA) on the properties of isotactic polypropylene (iPP) was investigated in the current research. β-NA was applied at the concentration ranged from 0.05 to 0.50 wt%. Microscopic observation revealed that the neat iPP crystals grew very slowly; they ranged in size from 100 to 200 μm. The addition of β-NA led to higher population of nuclei and smaller spherulites than those found in neat iPP. The addition of only 0.05 wt% β-NA significantly decreased the sizes of the spherulites down to 5 μm; the crystal grew very rapidly, leading to extremely fine morphology. Analysis by X-ray diffraction (XRD) confirmed that iPP/β-NA constituted mainly of β-crystal structure. The transformation of β to α phase was observed upon re-extrusion, it was verified by the lowered fraction of the β-crystalline phase (K{sub β}) although the total degree of crystallinity remained unchanged. A significant improvement in the impact strength of the iPP/β-NA was observed when the β-NA was employed from 0.10 to 0.20 wt%, leading to the formation of tough β-crystals in the β-NA nucleated iPP. The color measurement implied that the iPP nucleated with β-NA was superior in terms of whiteness but it was less transparent, as was evident by the increased haze.

Fabrication of nano piezoelectric based vibration accelerometer for mechanical sensing

Science.gov (United States)

Murugan, S.; Prasad, M. V. N.; Jayakumar, K.

2016-05-01

An electromechanical sensor unit has been fabricated using nano PZT embedded in PVDF polymer. Such a polymer nano composite has been used as vibration sensor element and sensitivity, detection of mechanical vibration, and linearity measurements have been investigated. It is found from its performance, that this nano composite sensor is suitable for mechanical sensing applications.

Effect of lateral size of graphene nano-sheets on the mechanical properties and machinability of alumina nano-composites

Czech Academy of Sciences Publication Activity Database

Porwal, H.; Saggar, Richa; Tatarko, P.; Grasso, S.; Saunders, T.; Dlouhý, Ivo; Reece, M. J.

2016-01-01

Roč. 42, č. 6 (2016), s. 7533-7542 ISSN 0272-8842 EU Projects: European Commission(XE) 264526 Institutional support: RVO:68081723 Keywords : Alumina * Graphene nano-sheets * Nano-composites * Mechanical properties * Machinability Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 2.986, year: 2016

Mechanistic study of the rubber-brass adhesion interphase

Science.gov (United States)

Ashirgade, Akshay

Brass-plated steel tire cords form an essential strengthening component of a radial automobile tire. Adhesion between rubber compound and brass-plated steel tire cord is crucial in governing the overall performance of tires. The rubber-brass interfacial adhesion is influenced by the chemical composition and thickness of the interfacial layer. It has been shown that the interfacial layer consists mainly of sulfides and oxides of copper and zinc. This thesis discusses the effect of changes in the chemical composition and the structure of the interfacial layers due to addition of adhesion promoter resins. Grazing incidence X-Ray Diffraction (GIXRD) experiments were run on sulfidized polished brass coupons previously bonded to six experimental rubber compounds. It was confirmed that heat and humidity conditions lead to physical and chemical changes of the rubber-steel tire cord interfacial layer, closely related to the degree of rubber-brass adhesion. Morphological transformation of the interfacial layer led to loss of adhesion after aging. The adhesion promoter resins inhibit unfavorable morphological changes in the interfacial layer thus stabilizing it during aging and prolonging failure. Tire cord adhesion tests illustrated that the one-component resins improved adhesion after aging using a rubber compound with lower cobalt loading. Based on the acquired diffraction profiles, these resins were also found to impede crystallization of the sulfide layer after aging leading to improved adhesion. Secondary Ion Mass Spectrometry (SIMS) depth profiles, SEM micrographs and AFM images strongly corroborated the findings from GIXRD. FTIR was utilized in a novel way to understand the degradation mechanism due to aging. A model for rubber and interfacial layer degradation is proposed to illustrate the effect of aging and the one-component resins. This interfacial analysis adds valuable new information to our understanding of the complex nature of the rubber-brass bonding

Bio-Based Nano Composites from Plant Oil and Nano Clay

Science.gov (United States)

Lu, Jue; Hong, Chang K.; Wool, Richard P.

2003-03-01

We explored the combination of nanoclay with new chemically functionalized, amphiphilic, plant oil resins to form bio-based nanocomposites with improved physical and mechanical properties. These can be used in many new applications, including the development of self-healing nanocomposites through controlled reversible exfoliation/intercalation, and self-assembled nano-structures. Several chemically modified triglyceride monomers of varying polarity, combined with styrene (ca 30include acrylated epoxidized soybean oil (AESO), maleated acrylated epoxidized soybean oil (MAESO) and soybean oil pentaerythritol glyceride maleates (SOPERMA), containing either hydroxyl group or acid functionality or both. The clay used is a natural montmorillonite modified with methyl tallow bis-2-hydroxyethyl quaternary ammonium chloride, which has hydroxyl groups. Both XRD and TEM showed a completely exfoliated structure at 3 wtwhen the clay content is above 5 wtconsidered a mix of intercalated and partially exfoliated structure. The controlled polarity of the monomer has a major effect on the reversible dispersion of clay in the polymer matrix. The bio-based nanocomposites showed a significant increase in flexural modulus and strength. Supported by EPA and DoE

A comparison study of polymer/cobalt ferrite nano-composites synthesized by mechanical alloying route

Directory of Open Access Journals (Sweden)

Sedigheh Rashidi

2015-12-01

Full Text Available In this research, the effect of different biopolymers such as polyethylene glycol (PEG and polyvinylalcohol (PVA on synthesis and characterization of polymer/cobalt ferrite (CF nano-composites bymechanical alloying method has been systematically investigated. The structural, morphological andmagnetic properties changes during mechanical milling were investigated by X-ray diffraction (XRD,Fourier transform infrared spectroscopy (FTIR, transmission electron microscopy (TEM, fieldemission scanning electron microscopy (FESEM, and vibrating sample magnetometer techniques(VSM, respectively. The polymeric cobalt ferrite nano-composites were obtained by employing atwo-step procedure: the cobalt ferrite of 20 nm mean particle size was first synthesized by mechanicalalloying route and then was embedded in PEG or PVA biopolymer matrix by milling process. Theresults revealed that PEG melted due to the local temperature raise during milling. Despite thisphenomenon, cobalt ferrite nano-particles were entirely embedded in PEG matrix. It seems, PAV is anappropriate candidate for producing nano-composite samples due to its high melting point. InPVA/CF nano-composites, the mean crystallite size and milling induced strain decreased to 13 nm and0.48, respectively. Moreover, milling process resulted in well distribution of CF in PVA matrix eventhough the mean particle size of cobalt ferrite has not been significantly affecetd. FTIR resultconfirmed the attachment of PVA to the surface of nano-particles. Magnetic properties evaluationshowed that saturation magnetization and coercivity values decreased in nano-composite samplecomparing the pure cobalt ferrite.

High Hydrogen Thoraeus Rubber Gossamer Radiation Shielding for Human Protection, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — NanoSonic has recently developed ultra-lightweight, durable, high hydrogen containing Thoraeus Rubber™ nanocomposites that may serve as radiation protection for...

The role of carbon nanotubes in promoting the properties of carbon black-filled natural rubber/butadiene rubber composites

Directory of Open Access Journals (Sweden)

Jiangshan Gao

Full Text Available 80/20 natural rubber (NR/butadiene rubber (BR blends in which the carbon black (CB was replaced partially by multi-walled carbon nanotubes (MWCNTs according to the ratios m (CNTs: m (decreasing amount of CB = 1: X (X was varied from 1 to 6, was prepared by blending of internal mixer and the two-roll mill at the mill opening of 0.5 mm for 10 times. SEM and TEM were used to investigate the filler networks and the good dispersion of fillers. The compounds containing 5 phr CNTs/27.5 phr CB exhibited the best abrasion resistance which was increased by 12.69% compared that without CNTs. 3D morphology images of wear surfaces and tensile fracture surfaces being similar to the layered map of the geography, which match the abrasion resistance and tensile properties, were observed by 3D measuring laser microscope. The uncured blend with 5 phr CNTs/35 phr CB showed the shortest cure time, the highest modulus and level of crosslink density. Significant improvement in mechanical properties were achieved by incorporating 5 phr CNTs and 35 phr CB, and the tear strength, 100% and 300% modulus of the vulcanizate were enhanced by 36.36%, 61.29% and 31.63% compared with the composite with 0 phr CNTs/40 phr CB, respectively. Additionally, compared with the composite without CNTs, the thermal conductivity of the composites with 5 phr CNTs/35 phr CB is increased by an average of 6.15% at three different temperatures. These considerable reinforcements resulted from the synergistic effect of CNTs and CB. Keywords: Synergistic effect, Carbon nanotubes, DIN abrasion, Mechanical properties, Thermal conductivity, 3D measuring laser microscope

Evaluation of Shear Bond Strength of Orthodontic Brackets Bonded with Nano-Filled Composites

OpenAIRE

Chalipa, Javad; Akhondi, Mohammad Sadegh Ahmad; Arab, Sepideh; Kharrazifard, Mohammad Javad; Ahmadyar, Maryam

2013-01-01

Objectives: The purpose of this study was to evaluate the shear bond strength (SBS) of orthodontic brackets bonded with two types of nano-composites in comparison to a conventional orthodontic composite. Materials and Methods: Sixty extracted human first premolars were randomly divided into 3 groups each containing 20 teeth. In group I, a conventional orthodontic composite (Transbond XT) was used to bond the brackets, while two nano-composites (Filtek TM Supreme XT and AELITE Aesthetic Enamel...

Editorial Emerging Multifunctional Nano structures

International Nuclear Information System (INIS)

Fan, H.; Lu, Y.; Ramanath, G.; Pomposo, J.A.

2009-01-01

The interest in emerging nano structures is growing exponentially since they are promising building blocks for advanced multifunctional nano composites. In recent years, an evolution from the controlled synthesis of individual monodisperse nanoparticles to the tailored preparation of hybrid spherical and also unsymmetrical multiparticle nano structures is clearly observed. As a matter of fact, the field of nano structures built around a nano species such as inside, outside, and next to a nanoparticle is becoming a new evolving area of research and development with potential applications in improved drug delivery systems, innovative magnetic devices, biosensors, and highly efficient catalysts, among several others Emerging nano structures with improved magnetic, conducting and smart characteristics are currently based on the design, synthesis, characterization and modeling of multifunctional nano object-based materials. In fact, core-shell nanoparticles and other related complex nano architectures covering a broad spectrum of materials (from metal and metal oxide to fused carbon, synthetic polymer, and bio polymer structures) to nano structure morphologies (spherical, cylindrical, star-like, etc.) are becoming the main building blocks for next generation of drug delivery systems, advanced sensors and biosensors, or improved nano composites. The five papers presented in this special issue examine the preparation and characterization of emerging multifunctional materials, covering from hybrid asymmetric structures to engineering nano composites.

Hybrid joining of polyamide and hydrogenated acrylonitrile butadiene rubber through heat-resistant functional layer of silane coupling agent

Science.gov (United States)

Sang, Jing; Sato, Riku; Aisawa, Sumio; Hirahara, Hidetoshi; Mori, Kunio

2017-08-01

A simple, direct adhesion method was developed to join polyamide (PA6) to hydrogenated acrylonitrile butadiene rubber (HNBR) by grafting a functional layer of a silane coupling agent on plasma functionalized PA6 surfaces. The functional layer of the silane coupling agent was prepared using a self-assembly method, which greatly improved the heat resistance of PA6 from 153 °C up to 325 °C and the resulting PA6/HNBR joints showed excellent adhesion properties with cohesive failure between PA6 and HNBR. X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and nanoscale infrared microscopy and chemical imaging (Nano-IR, AFM-IR) were employed to characterize the surfaces and interfaces. The Nano-IR analysis method was employed for the first time to analyze the chemical structures of the adhesion interfaces between different materials and to establish the interface formation mechanism. This study is of significant value for interface research and the study of adhesion between resins and rubbers. There is a promising future for heat-resistant functional layers on resin surfaces, with potential application in fuel hose composite materials for the automotive and aeronautical industries.

Functionalization of Liquid Natural Rubber via Oxidative Degradation of Natural Rubber

Directory of Open Access Journals (Sweden)

Suhawati Ibrahim

2014-12-01

Full Text Available Natural rubber (NR is a high molecular weight natural polymer and can be degraded to liquid natural rubber (LNR leaving certain functional groups at the end of chains. In this study, LNR samples prepared via oxidative degradation using H2O2 and NaNO2 as reagents were found to have different end groups depending on the pH of the reaction medium. In an acidic medium, LNR with hydroxyl terminal groups was formed as the degradation reaction was initiated by hydroxyl radicals produced from decomposition of peroxynitrite acid. In contrast, a redox reaction took place in an alkaline medium to yield LNR with carbonyl terminal groups. The mechanisms of reaction are discussed and proposed to explain the formation of different end groups when reaction carried out in acidic and alkaline media. Chain degradation in an acidic medium seems to be more effective than in an alkaline medium, and thus yields LNR with lower Mn.

Advanced Booster Composite Case/Polybenzimidazole Nitrile Butadiene Rubber Insulation Development

Science.gov (United States)

Gentz, Steve; Taylor, Robert; Nettles, Mindy

2015-01-01

The NASA Engineering and Safety Center (NESC) was requested to examine processing sensitivities (e.g., cure temperature control/variance, debonds, density variations) of polybenzimidazole nitrile butadiene rubber (PBI-NBR) insulation, case fiber, and resin systems and to evaluate nondestructive evaluation (NDE) and damage tolerance methods/models required to support human-rated composite motor cases. The proposed use of composite motor cases in Blocks IA and II was expected to increase performance capability through optimizing operating pressure and increasing propellant mass fraction. This assessment was to support the evaluation of risk reduction for large booster component development/fabrication, NDE of low mass-to-strength ratio material structures, and solid booster propellant formulation as requested in the Space Launch System NASA Research Announcement for Advanced Booster Engineering Demonstration and/or Risk Reduction. Composite case materials and high-energy propellants represent an enabling capability in the Agency's ability to provide affordable, high-performing advanced booster concepts. The NESC team was requested to provide an assessment of co- and multiple-cure processing of composite case and PBI-NBR insulation materials and evaluation of high-energy propellant formulations.

Nitrate removal by Fe0/Pd/Cu nano-composite in groundwater.

Science.gov (United States)

Liu, Hongyuan; Guo, Min; Zhang, Yan

2014-01-01

Nitrate pollution in groundwater shows a great threat to the safety of drinking water. Chemical reduction by zero-valent iron is being considered as a promising technique for nitrate removal from contaminated groundwater. In this paper, Fe0/Pd/Cu nano-composites were prepared by the liquid-phase reduction method, and batch experiments of nitrate reduction by the prepared Fe0/Pd/Cu nano-composites under various operating conditions were carried out. It has been found that nano-Fe0/Pd/Cu composites processed dual functions: catalytic reduction and chemical reduction. The introduction of Pd and Cu not only improved nitrate removal rate, but also reduced the generation of ammonia. Nitrate removal rate was affected by the amount of Fe0/Pd/Cu, initial nitrate concentration, solution pH, dissolved oxygen (DO), reaction temperature, the presence of anions, and organic pollutant. Moreover, nitrate reduction by Fe0/Pd/Cu composites followed the pseudo-first-order reaction kinetics. The removal rate of nitrate and total nitrogen were about 85% and 40.8%, respectively, under the reaction condition of Fe-6.0%Pd-3.0%Cu amount of 0.25 g/L, pH value of 7.1, DO of 0.42 mg/L, and initial nitrate concentration of 100 mg/L. Compared with the previous studies with Fe0 alone or Fe-Cu, nano-Fe-6%Pd-3%Cu composites showed a better selectivity to N2.

Synthesis and characterization of nano silver ferrite composite

International Nuclear Information System (INIS)

Murthy, Y.L.N.; Kondala Rao, T.; Kasi viswanath, I.V.; Singh, Rajendra

2010-01-01

We report the synthesis of nano sized silver ferrite composite having the empirical formula AgFeO 2 by a co-precipitation method. The resulting powders are thin platelets, transparent and a rich ruby red in color in transmission. The X-ray diffraction (XRD) powder data consisted of only nine reflections, and the analysis showed the unit cell to be rhombohedral. The powders showed extensive XRD line broadening and the sizes of the crystals are calculated to be in the range 4-36.5 nm. The morphology of the silver ferrite composite studied using scanning electron microscope showed nano sized particles. The particle size is found to increase with increase in annealing temperature. The magnetic behavior, measured using a vibrating sample magnetometer, indicated a change from paramagnetic to ferromagnetic with increase in particle size.

Preparation and characterization of functionalized cellulose nano crystals with methyl adipoyl chloride used to prepare chitosan grafting nano composite

International Nuclear Information System (INIS)

Mesquita, Joao Paulo de; Teixeira, Ivo F.; Donnici, Claudio L.; Pereira, Fabiano V.

2011-01-01

Cellulose nano crystals (CNCs) were prepared from eucalyptus pulp and functionalized with methyl adipoyl chloride. The nano materials were characterized by different techniques including FTIR, 1H NMR and XRD which showed that the functionalization occurs only on the surface of the nano structures without change in crystalline structure of the nanoparticles. The new-functionalized CNCs were used as reinforcement in the preparation of a nano composite with chitosan, through the formation of a covalent bond between the nano filler and matrix. Preliminary results of mechanical tests indicate an improvement in tensile strength and increase in deformation of chitosan. (author)

Study of the Properties of Polyurethane-waste Rubber Granulate Composites

Institute of Scientific and Technical Information of China (English)

W.W.Sulkowski; M.Moczy′ski; A.Sulkowska; A.Danch; J.Borek; S.Mistarz

2007-01-01

1 Results The production of rubber is very high and rises every year. Among other things it is directly connected with the growth of car production. Therefore, the processing of waste rubber and its management must be treated as a global problem. Used rubber may replace conventional fuel and, owing to its low price, can improve the economic effectiveness of combustion. Energy recovery by combustion of car tyres allows for rapid management of rubber waste. However, it is well-known that all kinds of wast...

Effect of Amount of 3-Methacryloxy Propyl Thrimethoxysilane Coupling Agent and Nano Filling Structure on Physic-Mechanical Properties of Dental Resin Composite