WorldWideScience

Sample records for building isoc status

  1. Determination of 137Cs contamination depth distribution in building structures using geostatistical modeling of ISOCS measurements

    International Nuclear Information System (INIS)

    Decommissioning of nuclear building structures usually leads to large amounts of low level radioactive waste. Using a reliable method to determine the contamination depth is indispensable prior to the start of decontamination works and also for minimizing the radioactive waste volume and the total workload. The method described in this paper is based on geostatistical modeling of in situ gamma-ray spectroscopy measurements using the multiple photo peak method. The method has been tested on the floor of the waste gas surge tank room within the BR3 (Belgian Reactor 3) decommissioning project and has delivered adequate results. - Highlights: • 137Cs depth contamination was determined using the multiple photo peak method. • Geostatistical modeling was used to determine treatment depth areas and perform risk analysis. • Results were evaluated using laser scanning and long term gamma-ray spectroscopy. • Waste volume reduction of about 1/3 compared to a more traditional approach

  2. ISOCS for Free Release. Innovative Technology Summary Report

    International Nuclear Information System (INIS)

    ISOCS is a Germanium-detector gamma-ray characterization system that can identify specific nuclei, and quantitatively determine the corresponding radioactive inventory in situ. ISOCS response to a series of point sources surrounding it have been characterized using a Monte Carlo code. The steel-jacketed lead shielding can be mounted around the Germanium detector to provide 1 or 2 inches of shielding from background radiation, and to change the field of view between 30, 90, or 180 degrees. The detector rotates on the cart for alignment with the target. The computer controls the InSpector multichannel analyzer and the Genie-PC software provides peak identification, data and error analysis, and system quality assurance. The ISOXSW software is the key feature of the system in that it automatically determines the relationship between the radioactive source geometry, the measured count rate, and the amount of radioactive material present using the ISOCS characterized detector data

  3. Medication bezoar: Intestinal obstruction by an Isocal bezoar

    International Nuclear Information System (INIS)

    Medications may occasionally obstruct the gastrointestinal tract by virtue of their physical mass. Obturative obstruction of the alimentary tract is reportedly caused by an increasing number of medications, including hydroscopic bulk laxatives, cholestyramine, nonabsorbable antacids, and vitamin C tablets. Inspissated Isocal tube feedings caused jejunal obstruction in a postoperative patient. Medication bezoars are a rare cause of intestinal obstruction that may result in significant patient morbidity, including bowel necrosis, perforation, and peritonitis. The radiographic appearance may mimic an abdominal abscess. (orig.)

  4. Worldwide status of energy standards for buildings: Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Janda, K.B.; Busch, J.F.

    1993-02-01

    This informal survey was designed to gain information about the worldwide status of energy efficiency standards for buildings, particularly non-residential buildings such as offices, schools, and hotels. The project has three goals: 1. To understand and learn from the experience of countries with existing building energy standards; 2. To locate areas where these lessons might be applied and energy standards might be effectively proposed and developed; and 3. To share the information gathered with all participating countries. These appendices include the survey cover letter, the survey, and the details of selected energy standards in 35 countries, thus providing supporting material for the authors` article of the same title.

  5. Status and prospects of building energy efficiency in China

    Institute of Scientific and Technical Information of China (English)

    LONGWeiding; ZHOUHui

    2003-01-01

    The paper briefly describes situation of building energy consumption in China. The authors indicate some relations in building energy efficiency should be dealt with properly: energy saving and energy efficiency, envelopes and building services systems, energy use and indoor environment, electric power saving and energy saving, devices and system, energy efficiency at stable state and at dynamic state. The authors suggest to use Coefficient of Energy Consumption as a Indicator of building energy efficiency.

  6. Status and Perceptions of the Application of Building Information Modeling for Improved Building Projects Delivery in Nigeria

    Directory of Open Access Journals (Sweden)

    S.C Ugochukwu

    2015-11-01

    Full Text Available Building Information Modeling (BIM is a new and innovative approach to building design, construction, and management. It is a cutting-edge, state of the art technology that is not only transforming, but improving the building delivery/production process in developed countries of the world. Sadly, Nigeria is yet to adopt this revolutionary technology in her construction industry. This study thus, sought to evaluate the present status of application of BIM in building projects in Nigeria, with a view to betoning its importance in improving the present state of building delivery in the country. This was effected by means of a field survey of building professionals in which their perceptions were analyzed, based on a structured questionnaire administration; in order to elicit their level of awareness of BIM application, determine their extent of participation in BIM projects, identify and rank the most suitable procurement method that encourages BIM application, the barriers to the application of BIM and the benefits of BIM application to building delivery in Nigeria. Results/Findings revealed that knowledge of BIM application among professionals is very poor (33%, participation/use of BIM in projects is non-existent, the collaborative method of procurement best supports BIM application, lack of awareness remains the major barrier to BIM application, while simultaneous access to project database by stakeholders is the highest ranked benefit of BIM application. The study concludes that Nigeria still has a long way to go in understanding, embracing and applying BIM to improve the traditional and stagnant state of her building delivery process. Hence, all hands should be on deck; the government, professional bodies, construction organizations and the academia to ensure that BIM becomes a priority with respect to legislations, training, research and use in the Nigerian building industry

  7. The status of adolescent medicine: building a global adolescent workforce.

    Science.gov (United States)

    Lee, Lana; Upadhya, Krishna K; Matson, Pamela A; Adger, Hoover; Trent, Maria E

    2016-08-01

    Remarkable public health achievements to reduce infant and child mortality as well as improve the health and well-being of children worldwide have successfully resulted in increased survival and a growing population of young people aged 10-24 years. Population trends indicate that the current generation of 1.8 billion young people is the largest in history. However, there is a scarcity of dedicated resources available to effectively meet the health needs of adolescents and young adults worldwide. Growing recognition of the pivotal roles young people play in the cultures, societies, and countries in which they live has spurred an expanding global movement to address the needs of this special population. Building an effective global workforce of highly-skilled adolescent health professionals who understand the unique biological, psychological, behavioral, social, and environmental factors that affect the health of adolescents is a critical step in addressing the health needs of the growing cohort of young people. In this review, we aim to: 1) define a global assessment of the health needs for adolescents around the world; 2) describe examples of current training programs and requirements in adolescent medicine; 3) identify existing gaps and barriers to develop an effective adolescent health workforce; and 4) develop a call for targeted actions to build capacity of the adolescent health workforce, broaden culturally relevant research and evidence-based intervention strategies, and reinforce existing interdisciplinary global networks of youth advocates and adolescent health professionals to maximize the opportunities for training, research, and care delivery. PMID:26167974

  8. ACCELERATED SITE TECHNOLOGY DEPLOYMENT COST AND PERFORMANCE REPORT COMPARABILITY OF ISOCS INSTRUMENT IN RADIONUCLIDE CHARACTERICATION AT BROOKHAVEN NATIONAL LABORATORY

    Energy Technology Data Exchange (ETDEWEB)

    KALB,P.; LUCKETT,L.; MILLER,K.; GOGOLAK,C.; MILIAN,L.

    2001-03-01

    This report describes a DOE Accelerated Site Technology Deployment project being conducted at Brookhaven National Laboratory to deploy innovative, radiological, in situ analytical techniques. The technologies are being deployed in support of efforts to characterize the Brookhaven Graphite Research Reactor (BGRR) facility, which is currently undergoing decontamination and decommissioning. This report focuses on the deployment of the Canberra Industries In Situ Object Counting System (ISOCS) and assesses its data comparability to baseline methods of sampling and laboratory analysis. The battery-operated, field deployable gamma spectrometer provides traditional spectra of counts as a function of gamma energy. The spectra are then converted to radionuclide concentration by applying innovative efficiency calculations using monte carlo statistical methods and pre-defined geometry templates in the analysis software. Measurement of gamma emitting radionuclides has been accomplished during characterization of several BGRR components including the Pile Fan Sump, Above Ground Ducts, contaminated cooling fans, and graphite pile internals. Cs-137 is the predominant gamma-emitting radionuclide identified, with smaller quantities of Co-60 and Am-241 detected. The Project used the Multi-Agency Radiation Survey and Site Investigation Manual guidance and the Data Quality Objectives process to provide direction for survey planning and data quality assessment. Analytical results have been used to calculate data quality indicators (DQI) for the ISOCS measurements. Among the DQIs assessed in the report are sensitivity, accuracy, precision, bias, and minimum detectable concentration. The assessment of the in situ data quality using the DQIs demonstrates that the ISOCS data quality can be comparable to definitive level laboratory analysis when the field instrument is supported by an appropriate Quality Assurance Project Plan. A discussion of the results obtained by ISOCS analysis of

  9. Optimization of ISOCS Parameters for Quantitative Non-Destructive Analysis of Uranium in Bulk Form

    Science.gov (United States)

    Kutniy, D.; Vanzha, S.; Mikhaylov, V.; Belkin, F.

    2011-12-01

    Quantitative calculation of the isotopic masses of fissionable U and Pu is important for forensic analysis of nuclear materials. γ-spectrometry is the most commonly applied tool for qualitative detection and analysis of key radionuclides in nuclear materials. Relative isotopic measurement of U and Pu may be obtained from γ-spectra through application of special software such as MGAU (Multi-Group Analysis for Uranium, LLNL) or FRAM (Fixed-Energy Response Function Analysis with Multiple Efficiency, LANL). If the concentration of U/Pu in the matrix is unknown, however, isotopic masses cannot be calculated. At present, active neutron interrogation is the only practical alternative for non-destructive quantification of fissionable isotopes of U and Pu. An active well coincidence counter (AWCC), an alternative for analyses of uranium materials, has the following disadvantages: 1) The detection of small quantities (≤100 g) of 235U is not possible in many models; 2) Representative standards that capture the geometry, density and chemical composition of the analyzed unknown are required for precise analysis; and 3) Specimen size is severely restricted by the size of the measuring chamber. These problems may be addressed using modified γ-spectrometry techniques based on a coaxial HPGe-detector and ISOCS software (In Situ Object Counting System software, Canberra). We present data testing a new gamma-spectrometry method uniting actinide detection with commonly utilized software, modified for application in determining the masses of the fissionable isotopes in unknown samples of nuclear materials. The ISOCS software, widely used in radiation monitoring, calculates the detector efficiency curve in a specified geometry and range of photon energies. In describing the geometry of the source-detector, it is necessary to clearly describe the distance between the source and the detector, the material and the thickness of the walls of the container, as well as material, density

  10. Application of ISOCS sourceless calibration software on designment for the shield thickness of collimator

    International Nuclear Information System (INIS)

    The designment for collimator need consider not only the factors about spatial resolution, sensitivity etc, but also the effect on shadow areas because of the shield thickness. One optimized method for the designment of the shield thickness of collimator, and the curve of the angle response and the percent of count contribution at different angle range for the infinite plane source were calculated with ISOCS when the types of collimator using in this process were 5 cm-30, 10 cm-30 and 15 cm-30. The results indicate that when the shield thickness of collimator is 5 cm, and the azimuthal angle is 90 degrees, the count countribution still exist, and the shadow area is large. And when the thickness is 15 cm,the visual field of the detector is controlled well. The method not only supply basis to the designment for the shield thickness of collimator, but also can be seen as the references of efficiency calibration and uncertainty evaluation for the detector with collimator. (authors)

  11. Zero Emission Buildings in Korea—History, Status Quo, and Future Prospects

    OpenAIRE

    Thorsten Schuetze

    2015-01-01

    This paper discusses the history, status quo, and future prospects of Zero Emission Buildings (ZEBs) in the Republic of Korea. The advantages of, and requirements for ZEBs are described, concerning the factors of energy, water, nutrients, and biomass. ZEBs are characterized by net zero energy consumption through the minimization of the energy demand, as well as the onsite production and use of renewable energy. The direct water footprint is reduced by up to 100% through on-site water supply a...

  12. Site status monitoring report for underground storage tank 2331-U at Building 9201-1

    International Nuclear Information System (INIS)

    The purpose of this document is to present potentiometric, groundwater quality and vapor monitoring data required for site status monitoring of underground storage tank (UST) 2331-U at the Building 9201-1 Site. Site status monitoring has been conducted at the site as part of a Monitoring Only program approved by the Tennessee Department of Environment and Conservation (TDEC) based on review and approval of Site Ranking (Site Ranking Form approved May 23, 1994). This document presents the results of the first semiannual site status monitoring that was performed in December 1994. Site status monitoring and preparation of this report have been conducted in accordance with the requirements of TDEC Rule 1200-1-15 and the TDEC UST Reference Handbook, Second Edition (TDEC 1994) Technical Guidance Document (TGD) 007. This document is organized into three sections. Section 1 presents introductory information relative to the site including the regulatory initiative and a site description. Section 2 includes the results of measurement and sampling of monitoring wells GW-193, GW-657, GW-707, GW-708, GW-808, GW-809, and GW-810. Section 3 presents data from vapor monitoring conducted in subsurface utilities present at the site

  13. Noninvasive CT to Iso-C3D registration for improved intraoperative visualization in computer assisted orthopedic surgery

    Science.gov (United States)

    Rudolph, Tobias; Ebert, Lars; Kowal, Jens

    2006-03-01

    Supporting surgeons in performing minimally invasive surgeries can be considered as one of the major goals of computer assisted surgery. Excellent intraoperative visualization is a prerequisite to achieve this aim. The Siremobil Iso-C 3D has become a widely used imaging device, which, in combination with a navigation system, enables the surgeon to directly navigate within the acquired 3D image volume without any extra registration steps. However, the image quality is rather low compared to a CT scan and the volume size (approx. 12 cm 3) limits its application. A regularly used alternative in computer assisted orthopedic surgery is to use of a preoperatively acquired CT scan to visualize the operating field. But, the additional registration step, necessary in order to use CT stacks for navigation is quite invasive. Therefore the objective of this work is to develop a noninvasive registration technique. In this article a solution is being proposed that registers a preoperatively acquired CT scan to the intraoperatively acquired Iso-C 3D image volume, thereby registering the CT to the tracked anatomy. The procedure aligns both image volumes by maximizing the mutual information, an algorithm that has already been applied to similar registration problems and demonstrated good results. Furthermore the accuracy of such a registration method was investigated in a clinical setup, integrating a navigated Iso-C 3D in combination with an tracking system. Initial tests based on cadaveric animal bone resulted in an accuracy ranging from 0.63mm to 1.55mm mean error.

  14. Radiological status report for the EBWR containment building. Volume 1: Summary and analysis

    International Nuclear Information System (INIS)

    At the conclusion of the EBWR D and D process, ANL Health Physics conducted a release survey to determine the radiological status of the facility. The primary goal of the survey was to verify that residual activities on building surfaces met DOE and ANL guidelines for downposting of a Radiologically Contaminated Area to a Radiologically Controlled Area. The resultant area was to bear no contamination designation, with no requirements for radiological personnel monitoring or protective clothing. ANL Health Physics designed a survey procedure, using a graded approach considering the building history, the D and D process, and the intended future use. The survey followed the general guidance of NRC NUREG/CR-5849, but simplified and reduced in scope to match the release goal. The building interior surfaces were divided into 15 principal survey units and one special survey unit. Each of the principal survey units had to meet the controlled release guidelines. The procedure consisted of dual full floor scans for beta/gamma activity, sampling measurements of total and removable alpha and beta/gamma activities, and background gamma exposure surveys. In the 15 principal survey units, surface activities were measured at a total of 444 locations. With the exception of certain excluded contaminated areas and mechanical equipment, the building interior meets the limited release guidelines

  15. Estudio bibliométrico de la literatura sobre el libro antiguo en la base de datos ISOC A biblometric study of the literature on old books in the ISOC database

    Directory of Open Access Journals (Sweden)

    Antonio Pulgarín Guerrero

    2013-04-01

    Full Text Available Se recopilan 907 trabajos relacionados con libros antiguos incluidos en la base de datos ISOC, para realizar un estudio bibliométrico (860 artículos de revistas y 47 colaboraciones presentadas a congresos. Se establece el siguiente esquema de estudio para analizar los trabajos localizados: distribución por tipo de publicación, por materias, por años de publicación, por nombre de las revistas, por autores; también se establece la dispersión de la literatura, la productividad científica de los autores y las características de las revistas según se indica en RESH (Revistas Españolas de Ciencias Sociales y Humanidades.A bibliometric study describes 907 works on old books included in the ISOC database (860 journal articles and 47 papers presented at conferences. The study analyzed distribution by type and year of publication, subject, journal name, and authors. The diffusion of the literature, the authors' scientific productivity and the characteristics of the journals as indicated in RESH are also described.

  16. Simulating electron momentum spectra of iso-C2H2Cl2: A study of the core electronic structure

    International Nuclear Information System (INIS)

    Electron momentum spectroscopy (EMS) has been used for the first time to study core electronic structure of iso-C2H2Cl2. In the present work, the pronounced difference between ionization energies of two C1s core orbitals (2A1 and 3A1) is seen as a chemical shift of 3 eV, which is due to different chemical environments of the related carbon atoms. Both the calculated spherically averaged core electron momentum distributions (MDs) and three-dimensional electron momentum density maps show that these core molecular orbitals (MOs) 2A1 and 3A1 exhibit strong atomic orbital characteristics in real and momentum space. However, the core states 2B2 and 4A1, which are almost degenerate and related to two equivalent atoms, exhibit notable differences between the momentum and position depictions. In contrast to the position space, the momentum density maps of these two core MOs highlight the interference effects which are due to the nuclear positions. The 2B2 orbital of iso-C2H2Cl2 is the antisymmetric counterpart of the 4A1 core orbital in real space. However, it relates to the 4A1 orbital by an exchange of maxima and minima in momentum space. Due to interference effects between electrons scattered from different atomic centers, modulations with a periodicity of 1.12 a.u. can be seen in the computed momentum densities, which tend to decay with increasing electron momenta. Accordingly, the EMS can not only effectively image the electronic structure of compounds by studying valence orbitals, but also provides direct information on the nature of the nuclear geometry by investigating the core states. (atomic and molecular physics)

  17. Building

    OpenAIRE

    Seavy, Ryan

    2014-01-01

    Building for concrete is temporary. The building of wood and steel stands against the concrete to give form and then gives way, leaving a trace of its existence behind. Concrete is not a building material. One does not build with concrete. One builds for concrete.

  18. A practical synthesis of long-chain iso-fatty acids (iso-C12–C19 and related natural products

    Directory of Open Access Journals (Sweden)

    Mark B. Richardson

    2013-09-01

    Full Text Available A gram-scale synthesis of terminally-branched iso-fatty acids (iso-C12–C19 was developed commencing with methyl undec-10-enoate (methyl undecylenate (for iso-C12–C14 or the C15 and C16 lactones pentadecanolide (for iso-C15–C17 and hexadecanolide (for iso-C18–C19. Central to the approaches outlined is the two-step construction of the terminal isopropyl group through addition of methylmagnesium bromide to the ester/lactones and selective reduction of the resulting tertiary alcohols. Thus, the C12, C17 and C18 iso-fatty acids were obtained in three steps from commercially-available starting materials, and the remaining C13–C16 and C19 iso-fatty acids were prepared by homologation or recursive dehomologations of these fatty acids or through intercepting appropriate intermediates. Highlighting the synthetic potential of the iso-fatty acids and various intermediates prepared herein, we describe the synthesis of the natural products (S-2,15-dimethylpalmitic acid, (S-2-hydroxy-15-methylpalmitic acid, and 2-oxo-14-methylpentadecane.

  19. Final Status Survey Report for Corrective Action Unit 117 - Pluto Disassembly Facility, Building 2201, Nevada National Security Site, Nevada

    International Nuclear Information System (INIS)

    This document contains the process knowledge, radiological data and subsequent statistical methodology and analysis to support approval for the radiological release of Corrective Action Unit (CAU) 117 - Pluto Disassembly Facility, Building 2201 located in Area 26 of the Nevada National Security Site (NNSS). Preparations for release of the building began in 2009 and followed the methodology described in the Multi-Agency Radiation Survey and Site Investigation Manual (MARSSIM). MARSSIM is the DOE approved process for release of Real Property (buildings and landmasses) to a set of established criteria or authorized limits. The pre-approved authorized limits for surface contamination values and corresponding assumptions were established by DOE O 5400.5. The release criteria coincide with the acceptance criteria of the U10C landfill permit. The U10C landfill is the proposed location to dispose of the radiologically non-impacted, or ''clean,'' building rubble following demolition. However, other disposition options that include the building and/or waste remaining at the NNSS may be considered providing that the same release limits apply. The Final Status Survey was designed following MARSSIM guidance by reviewing historical documentation and radiological survey data. Following this review a formal radiological characterization survey was performed in two phases. The characterization revealed multiple areas of residual radioactivity above the release criteria. These locations were remediated (decontaminated) and then the surface activity was verified to be less than the release criteria. Once remediation efforts had been successfully completed, a Final Status Survey Plan (10-015, ''Final Status Survey Plan for Corrective Action Unit 117 - Pluto Disassembly Facility, Building 2201'') was developed and implemented to complete the final step in the MARSSIM process, the Final Status Survey. The Final Status Survey Plan consisted of categorizing each individual room into one

  20. Final Status Survey Report for Corrective Action Unit 117 - Pluto Disassembly Facility, Building 2201, Nevada National Security Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Jeremy Gwin and Douglas Frenette

    2010-09-30

    This document contains the process knowledge, radiological data and subsequent statistical methodology and analysis to support approval for the radiological release of Corrective Action Unit (CAU) 117 – Pluto Disassembly Facility, Building 2201 located in Area 26 of the Nevada National Security Site (NNSS). Preparations for release of the building began in 2009 and followed the methodology described in the Multi-Agency Radiation Survey and Site Investigation Manual (MARSSIM). MARSSIM is the DOE approved process for release of Real Property (buildings and landmasses) to a set of established criteria or authorized limits. The pre-approved authorized limits for surface contamination values and corresponding assumptions were established by DOE O 5400.5. The release criteria coincide with the acceptance criteria of the U10C landfill permit. The U10C landfill is the proposed location to dispose of the radiologically non-impacted, or “clean,” building rubble following demolition. However, other disposition options that include the building and/or waste remaining at the NNSS may be considered providing that the same release limits apply. The Final Status Survey was designed following MARSSIM guidance by reviewing historical documentation and radiological survey data. Following this review a formal radiological characterization survey was performed in two phases. The characterization revealed multiple areas of residual radioactivity above the release criteria. These locations were remediated (decontaminated) and then the surface activity was verified to be less than the release criteria. Once remediation efforts had been successfully completed, a Final Status Survey Plan (10-015, “Final Status Survey Plan for Corrective Action Unit 117 – Pluto Disassembly Facility, Building 2201”) was developed and implemented to complete the final step in the MARSSIM process, the Final Status Survey. The Final Status Survey Plan consisted of categorizing each individual room

  1. Clinical Accuracy of Three-Dimensional Fluoroscopy (IsoC-3D-Assisted Upper Thoracic Pedicle Screw Insertion

    Directory of Open Access Journals (Sweden)

    Sugimoto,Yoshihisa

    2010-06-01

    Full Text Available Correct screw placement is especially difficult in the upper thoracic vertebrae. At the cervicothoracic junction (C7-T2, problems can arise because of the narrowness of the pedicle and the difficulty of using a lateral image intensifier there. Other upper thoracic vertebrae (T3-6 pose a problem for screw insertion also because of the narrower pedicle. We inserted 154 pedicle screws into 78 vertebrae (C7 to T6 in 38 patients. Screws were placed using intraoperative data acquisition by an isocentric C-arm fluoroscope (Siremobile Iso-C3D and computer navigation. Out of 90 pedicle screws inserted into 45 vertebrae between C7 and T2, 87 of the 90 (96.7% screws were classified as grade 1 (no perforation. Of 64 pedicle screws inserted into 33 vertebrae between T3 and T6, 61 of 64 (95.3% screws were classified as grade 1. In this study, we reduced pedicle screw misplacement at the level of the C7 and upper thoracic (T1-6 vertebrae using the three-dimensional fluoroscopy navigation system.

  2. Clinical accuracy of three-dimensional fluoroscopy (IsoC-3D)-assisted upper thoracic pedicle screw insertion

    International Nuclear Information System (INIS)

    Correct screw placement is especially difficult in the upper thoracic vertebrae. At the cervicothoracic junction (C7-T2), problems can arise because of the narrowness of the pedicle and the difficulty of using a lateral image intensifier there. Other upper thoracic vertebrae (T3-6) pose a problem for screw insertion also because of the narrower pedicle. We inserted 154 pedicle screws into 78 vertebrae (C7 to T6) in 38 patients. Screws were placed using intraoperative data acquisition by an isocentric C-arm fluoroscope (Siremobile Iso-C3D) and computer navigation. Out of 90 pedicle screws inserted into 45 vertebrae between C7 and T2, 87 of the 90 (96.7%) screws were classified as grade 1 (no perforation). Of 64 pedicle screws inserted into 33 vertebrae between T3 and T6, 61 of 64 (95.3%) screws were classified as grade 1. In this study, we reduced pedicle screw misplacement at the level of the C7 and upper thoracic (T1-6) vertebrae using the three-dimensional fluoroscopy navigation system. (author)

  3. Status of the spent fuel in the reactor buildings of Fukushima Daiichi 1–4

    Energy Technology Data Exchange (ETDEWEB)

    Jäckel, Bernd S., E-mail: bernd.jaeckel@psi.ch

    2015-03-15

    The ratios of the radionuclides Cs-134g and Cs-137 deduced from measurements of liquid samples from the spent fuel pools in Fukushima Daiichi 1–4 are used to interpret the status of the spent fuel assemblies in the pools of the damaged reactor buildings. The different natures of the production of Cs-134g (neutron capture product of Cs-133) and Cs-137 (cumulative fission product from mass chain 137) and the different half-lives (2.06 years and 30.17 years respectively) require a complicated calculation of the mass and activity of the two nuclides. These masses are depending on the local burn up of the fuel, the burn up history and the radioactive decay. Calculation of the neutron capture product Cs-134g is particularly complicated, because the production of Cs-133 (stable cumulative fission product from mass chain 133) has to be taken into account. The neutron capture cross section for Cs-133 for thermal neutrons is well known, but the energy spectrum of the neutrons in a reactor includes higher energies according to the degree of moderation. Therefore the cross section was fitted from a gamma scan of spent fuel rods in a hot cell. The method of the calculation of the nuclide activities and the interpretation of the gamma measurements of the spent fuel pool samples from Fukushima Daiichi 1–4 are described in detail. It could be shown that at most only very minor mechanical damage of some spent fuel elements occurred during the accident and the later phase of the clearing work.

  4. Studies on image quality, high contrast resolution and dose for the axial skeleton and limbs with a new, dedicated CT system (ISO-C-3D)

    International Nuclear Information System (INIS)

    Purpose: Evaluation of 3D-CT imaging of the axial skeleton and different joints of the lower and upper extremities with a new dedicated CT system (ISO-C-3D) based on a mobile isocentric C-arm image amplifier. Material and Methods: 27 cadaveric specimes of different joints of the lower and upper extremities and of the spinal column were examined with 3D-CT imaging (ISO-C-3d). All images were evaluated by 3 radiologists for image quality using a semiquantitative score (score value 1: poor quality; score value 4: excellent quality). In addition, dose measurements and measurements of high contrast resolution were performed in comparison to conventional and low-dose spiral CT using a high contrast phantom (Catphan, Phantom Laboratories). Results: Adequate image quality (mean score values 3-4) could be achieved with an applied dose comparable to low-dose CT in smaller joints such as wrist, elbow, ankle and knee. A remarkably inferior image quality resulted in imaging of the hip, lumbar and thoracic spine (mean score values 2-3) in spite of almost doubling the dose (dose increased by 85 percent). The image quality of shoulder examinations was insufficient (mean score value 1). Phantom studies showed a high-contrast resolution comparable to helical CT in the xy-axis (9 lp/cm). Conclusion: Preliminary results show, that image quality of C-arm-based CT-imaging (ISO-C-3D) seems to be adequate in smaller joints. ISO-C-3D images of the hip and axial skeleton show a decreased image quality, which does not seem to be sufficient for diagnosing subtle fractures. (orig.)

  5. Detection of tibial condylar fractures using 3D imaging with a mobile image amplifier (Siemens ISO-C-3D): Comparison with plain films and spiral CT

    International Nuclear Information System (INIS)

    Purpose: To analyze a prototype mobile C-arm 3D image amplifier in the detection and classification of experimental tibial condylar fractures with multiplanar reconstructions (MPR). Method: Human knee specimens (n=22) with tibial condylar fractures were examined with a prototype C-arm (ISO-C-3D, Siemens AG), plain films (CR) and spiral CT (CT). The motorized C-arm provides fluoroscopic images during a 190 orbital rotation computing a 119 mm data cube. From these 3D data sets MP reconstructions were obtained. All images were evaluated by four independent readers for the detection and assessment of fracture lines. All fractures were classified according to the Mueller AO classification. To confirm the results, the specimens were finally surgically dissected. Results: 97% of the tibial condylar fractures were easily seen and correctly classified according to the Mueller AO classification on MP reconstruction of the ISO-C-3D. There is no significant difference between ISO-C and CT in detection and correct classification of fractures, but ISO-CD-3D is significant by better than CR. (orig.)

  6. Status of Electron-Cloud Build-Up Simulations for the Main Injector

    Energy Technology Data Exchange (ETDEWEB)

    Furman, M. A.; Kourbanis, I.; Zwaska, R. M.

    2009-05-04

    We provide a brief status report on measurements and simulations of the electron cloud in the Fermilab Main Injector. Areas of agreement and disagreement are spelled out, along with their possible significance.

  7. Status of Electron-Cloud Build-Up Simulations for the Main Injector

    OpenAIRE

    Furman, M.A.

    2011-01-01

    We provide a brief status report on measurements and simulations of the electron cloud in the Fermilab Main Injector. Areas of agreement and disagreement are spelled out, along with their possible significance.

  8. International Monitoring system (IMS) build-up in Africa: Current status and the way forward

    International Nuclear Information System (INIS)

    The complete IMS verification system for primary and auxiliary seismic together with that of radionuclide, hydroacoustic and infrasound is plotted on a global map and Africa in particular showing its status. IMS situation in East and Southern Africa is included

  9. SU-E-J-46: Evaluation of the Accuracy of a Six Degree of Freedom Robotic Couch Using ConeBeam CT Images of the Isocal Phantom

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Q; Driewer, J; Wang, S; Li, S; Zheng, D; Zhu, X; Zhen, W; Wahl, A; Lin, C; Thompson, R; Zhou, S; Enke, C [University of Nebraska Medical Center, Omaha, NE (United States)

    2015-06-15

    Purpose The accuracy of Varian PerfectPitch six degree of freedom (DOF) robotic couch was examined using Varian Isocal phantom and cone-beam CT (CBCT) system. Methods CBCT images of the Isocal phantom were taken at different pitch and roll angles. The pitch and roll angles were varied from 357 to 3 degrees in one degree increments by input from service console, generating a total of 49 combinations with couch angle (yaw) zero. The center positions of the 16 tungsten carbide BBs contained in the Isocal were determined with in-house image processing software. Expected BBs positions at different rotation angles were determined mathematically by applying a combined translation/rotation operator to BB positions at zero pitch and roll values. A least square method was used to minimize the difference between the expected BB positions and their measured positions. In this way rotation angles were obtained and compared with input values from the console. Results A total of 49 CBCT images with voxel sizes 0.51 mm × 0.51 mm × 1 mm were used in analysis. Among the 49 calculations, the maximum rotation angle differences were 0.1 degree, 0.15 degree, and 0.09 degree, for pitch, roll, and couch rotation, respectively. The mean ± standard-deviation angle differences were 0.028±0.001 degree, −0.043±0.003 degree, and −0.009±0.001 degree, for pitch, roll, and couch rotation, respectively. The maximum isocenter shifts were 0.3 mm, 0.5 mm, 0.4 mm in x, y, z direction respectively following IEC6127 convention. The mean isocenter shifts were 0.07±0.02 mm, −0.05±0.06 mm, and −0.12±0.02 mm in x, y and z directions. Conclusion The accuracy of the Varian PerfectPitch six DOF couch was studied with CBCTs of the Isocal phantom. The rotational errors were less than 0.15 degree and isocenter shifts were less than 0.5 mm in any direction. This accuracy is sufficient for stereotactic radiotherapy clinical applications.

  10. Utilización de la proteína dietaría por alevinos de la gamitana, Colossoma macropomum, alimentados con dietas isocalóricas

    OpenAIRE

    Félix Walter Gutiérrez; Máximo Quispe; Luz Valenzuela; Guadalupe Contreras; Javier Zaldívar

    2011-01-01

    Un experimento fue conducido para evaluar los efectos de cinco niveles de proteína (25,27, 29, 31 y 33%) sobre el comportamiento productivo de alevinos de la gamitana, Colossoma macropomum Cuvier 1818, alimentados con dietas isocalóricas (2,7 kcal de ED/g). Los parámetros medidos fueron ganancia de peso (GP), conversión alimenticia (CA), proteína retenida (PR), razón de eficiencia proteica (REP) y energía retenida (ER). En la preparación de las dietas experimentales se utilizaron como fuentes...

  11. SU-E-J-46: Evaluation of the Accuracy of a Six Degree of Freedom Robotic Couch Using ConeBeam CT Images of the Isocal Phantom

    International Nuclear Information System (INIS)

    Purpose The accuracy of Varian PerfectPitch six degree of freedom (DOF) robotic couch was examined using Varian Isocal phantom and cone-beam CT (CBCT) system. Methods CBCT images of the Isocal phantom were taken at different pitch and roll angles. The pitch and roll angles were varied from 357 to 3 degrees in one degree increments by input from service console, generating a total of 49 combinations with couch angle (yaw) zero. The center positions of the 16 tungsten carbide BBs contained in the Isocal were determined with in-house image processing software. Expected BBs positions at different rotation angles were determined mathematically by applying a combined translation/rotation operator to BB positions at zero pitch and roll values. A least square method was used to minimize the difference between the expected BB positions and their measured positions. In this way rotation angles were obtained and compared with input values from the console. Results A total of 49 CBCT images with voxel sizes 0.51 mm × 0.51 mm × 1 mm were used in analysis. Among the 49 calculations, the maximum rotation angle differences were 0.1 degree, 0.15 degree, and 0.09 degree, for pitch, roll, and couch rotation, respectively. The mean ± standard-deviation angle differences were 0.028±0.001 degree, −0.043±0.003 degree, and −0.009±0.001 degree, for pitch, roll, and couch rotation, respectively. The maximum isocenter shifts were 0.3 mm, 0.5 mm, 0.4 mm in x, y, z direction respectively following IEC6127 convention. The mean isocenter shifts were 0.07±0.02 mm, −0.05±0.06 mm, and −0.12±0.02 mm in x, y and z directions. Conclusion The accuracy of the Varian PerfectPitch six DOF couch was studied with CBCTs of the Isocal phantom. The rotational errors were less than 0.15 degree and isocenter shifts were less than 0.5 mm in any direction. This accuracy is sufficient for stereotactic radiotherapy clinical applications

  12. Regulatory competence building framework for nuclear facilities in Mongolia, Status review and suggestion

    International Nuclear Information System (INIS)

    A regulatory body shall be effectively independent from organizations or bodies charged with the promotion of nuclear technologies or responsible for facilities or activities. An enhanced framework of regulatory staff is needed to ensure nuclear and radiation safety. Currently Mongolia does not have a nuclear power plant or any nuclear facilities. But there is a plan to use nuclear energy for peaceful purposes. The Mongolian parliament enacted a State policy for utilization of radioactive minerals and nuclear energy and Nuclear Energy Law. The aim of this paper is to investigate the regulatory competence building framework for nuclear facilities in Mongolia. This investigation concludes with suggestions to achieve the effective regulatory control of nuclear facilities and activities in Mongolia

  13. Status of Electron-Cloud Build-Up Simulations for the Main Injector

    International Nuclear Information System (INIS)

    We provide a brief status report on measurements and simulations of the electron cloud in the Fermilab Main Injector (MI). Areas of agreement and disagreement are spelled out, along with their possible significance. An upgrade to the MI is being considered that would increase the bunch intensity Nb, from the present ∼ 1 x 1011 to 3 x 1011, corresponding to a total pulse intensity Ntot = 16.4 x 1013, in order to generate intense beams for the neutrino program. Such an increase in beam intensity would place the MI in a parameter regime where other storage rings have seen a significant EC effect. Motivated by this concern, efforts have been undertaken over the recent past to measure and simulate the magnitude of the effect and to assess its operational implications on the proposed upgrade. We report here a summary of simulation results obtained with the code POSINST, and certain benchmarks against measurements. Unless stated otherwise, the simulation parameters used are shown in Tab. 1. Some of these represent a slightly simplified version of the MI operation.

  14. Nuclear new-build - Status and Outlook from a German utility perspective

    International Nuclear Information System (INIS)

    Full text: As one of the Top 5 utilities in Europe, Rheinisch-Westfaelisches Elektrizitaetswerk AG, FWB: RW, RWE, operates a diversified generating capacity of about 45 GW; RWE Power alone generates over 30 GW. Besides a share of approximately 20% nuclear power, a large proportion of the generating base is in lignite and hard coal. RWE has an ambitious, Euro10 bn newbuild program of about 10 GW modern fossil fired plants and further expansion plans across Europe. By 2012, RWE intends to invest between Euro 15 and 20 bn outside Germany.The European Union has a challenging policy to increase the share of renewables, improve energy efficiency, and reduce greenhouse gases by 2020. At the same time, ageing power plants need to be replaced. This requires an enormous investment program across Europe. Nuclear power therefore, as a proven technology with low lifecycle carbon emissions and reasonable lifecycle cost, is a crucial contributor to achieve Europe's 2020 goals. Accordingly, most European countries have started or are planning to expand their nuclear generating base by lifetime extension, capacity upgrades, and newbuild projects. Germany is one of the few countries where the Government has not yet adopted a pro-nuclear policy. Instead, the law of the land still forces early plant closures. Against this background, RWE is determined to reduce its CO2 exposure and grow internationally; work towards preserving nuclear energy in Germany; expand its nuclear energy-based generation portfolio in other markets, especially UK and CSEE. As a pioneer in the civilian nuclear industry, RWE can build on a wealth of experience for engaging in new nuclear projects. We have established a set of strict guidelines with which we evaluate project opportunities, starting with the fundamental requirement that, beyond any regulatory requirements, safety must be guaranteed according to RWE's high standards. On this basis, RWE has been successfully able to engage in two of the first nuclear

  15. 浅谈建筑工程招投标市场现状%Discussion on the status of market of inviting and submitting of building engineering

    Institute of Scientific and Technical Information of China (English)

    王燕军

    2009-01-01

    Through investigating and analyzing the market of inviting and subraitting of building engineering, the problems existing in present market of inviting and submitting of building engineering were generalized, the principle reasons of the phenomena were studied, the counter-measures to improve and complete market status of inviting and submitting of building engineering were proposed, so as to better standard building market order.%通过对建筑工程招投标市场的调查分析,归纳了当前建筑工程招投标市场存在的问题,研究了存在这些现象的主要原因,并提出了改进和完善建筑工程招投标市场现状的对策,从而更好地规范建筑市场秩序.

  16. The Influence of Status on the Relationship between Intergroup Contact, Threat, and Prejudice in the Context of a Nation-building Intervention in Malaysia

    OpenAIRE

    Ananthi Al Ramiah; Miles Hewstone; Little, Todd D.; Kyle Lang

    2014-01-01

    We assessed whether intergroup contact at a nation-building intervention in Malaysia improved participants’ perceptions of threat and outgroup evaluations and whether this process was conceptually moderated by group status in a three-group setting. We found evidence of a strong relationship between post-intervention contact and post-intervention outgroup evaluations in all groups and evidence of indirect effects of post-intervention contact on outgroup evaluations by symbolic threat for the...

  17. Evaluación de las bases de datos ISOC a través de un estudio de usuarios. Homenaje a José María Sánchez Nistal

    Directory of Open Access Journals (Sweden)

    Alcain, Mª Dolores

    2001-09-01

    Full Text Available The objective of this work is to approach the state of the art of the user’s studies about Quality Management and Evaluation of data bases, and to apply the existing models to a real case: the ISOC data base. To this end, two questionnaires have been designed: one addressed to end users and the other to reference librarians. The results show the differences between the two groups in the use, reasons for consultation, objectives and satisfaction. A difference in objectives and level of satisfaction has also been found between the two main users: researchers and professors on the one hand, and students, on the other. The results allow to establish a map of the use of ISOC data base and to obtain some value indicators. It is concluded that ISOC is very used and generally well valued. This kind of studies have proved to be necessary in order to follow up users’ requirements.

    El objetivo del presente estudio es realizar un acercamiento al estado de la cuestión de los estudios de usuarios en la gestión y evaluación de calidad de bases de datos y aplicar los modelos existentes a un caso real, la base de datos ISOC (CSIC. Para ello se diseñan dos cuestionarios, uno para usuarios finales y otro para bibliotecarios referencistas. Los resultados muestran diferencias entre ambos colectivos tanto en el uso, como en motivos de consulta, objetivos y nivel de satisfacción. También se observan objetivos y grado de satisfacción diferentes entre los dos grupos de usuarios más destacados, el mayoritario de ‘investigadores y docentes universitarios’ y el menos numeroso de ‘estudiantes’. Los datos obtenidos permiten establecer una radiografía sobre el uso de la base ISOC y obtener algunos indicadores de valoración de la misma. Se concluye que ISOC es muy utilizada y bien valorada en términos generales y se considera importante seguir realizando este tipo de estudios para poder hacer un seguimiento de las demandas de los usuarios.

  18. Study of the influence of the composition and density of the cement for the determination of the efficiency to the extent of using homogeneous packages ISOCS; Estudio de la influencia de la composicion y densidad del cemento para la determinacion de la eficiencia en la medida de bultors homogeneos mediante ISOCS

    Energy Technology Data Exchange (ETDEWEB)

    Marijuan, M. J.; Suarez-Navarro, J. A.; Esteban-Limenez, M. A.; Quinones, J.

    2013-07-01

    This work has studied the influence of the composition and density of the matrix, so as distance drum-detector in the determination of counting efficiencies, using Canberra [11-13], software ISOCS on drums with homogeneous residues. Also, efficiencies determined experimentally curves have been compared and using such software. The studies were carried out with the drum in a static position and with twist. A container prepared with soil samples was employed for the validation of the technical upgraded in the sample preparation laboratory and measured by the technique of segmented gamma spectrometry and the proposal in this paper. With the studies has established a methodology to determine the efficiency of measurement drums with waste homogeneous with twist.

  19. A search for natural bioactive compounds in Bolivia through a multidisciplinary approach. Part VI. Evaluation of the antimalarial activity of plants used by Isoceño-Guaraní Indians.

    Science.gov (United States)

    Bourdy, G; Oporto, P; Gimenez, A; Deharo, E

    2004-08-01

    Seventy-seven plant extracts (corresponding to 62 different species) traditionally used by the Isoceño-Guaraní, a native community living in the Bolivian Chaco, were screened for antimalarial activity in vitro on Plasmodium falciparum chloroquine sensitive strain (F32), and on ferriprotoporphyrin (FP) IX biocrystallisation inhibition test (FBIT). Among these extracts, seven displayed strong in vitro antimalarial activity, and 25 were active in the FBIT test. Positive results on both tests were recorded for six extracts: Argemone subfusiformis aerial part, Aspidosperma quebracho-blanco bark, Castela coccinea leaves and bark, Solanum argentinum leaves and Vallesia glabra bark. Results are discussed in relation with Isoceño-Guaraní traditional medicine. Further studies to be undertaken in relation with these results are also highlighted. PMID:15234764

  20. Utilización de la proteína dietaría por alevinos de la gamitana, Colossoma macropomum, alimentados con dietas isocalóricas

    Directory of Open Access Journals (Sweden)

    Félix Walter Gutiérrez

    2011-05-01

    Full Text Available Un experimento fue conducido para evaluar los efectos de cinco niveles de proteína (25,27, 29, 31 y 33% sobre el comportamiento productivo de alevinos de la gamitana, Colossoma macropomum Cuvier 1818, alimentados con dietas isocalóricas (2,7 kcal de ED/g. Los parámetros medidos fueron ganancia de peso (GP, conversión alimenticia (CA, proteína retenida (PR, razón de eficiencia proteica (REP y energía retenida (ER. En la preparación de las dietas experimentales se utilizaron como fuentes de proteína harina de anchoveta y harina de torta de soya y como fuentes de energía maíz amarillo duro, subproducto de trigo y aceite de pescado. Se encontraron diferencias significativas (P<0,05 entre tratamientos para los parámetros GP, PR, REP y ER. No se encontraron diferencias significativas para la CA. Los mejores rendimientos fueron obtenidos cuando las gamitanas fueron alimentadas con niveles dietarios de 25, 27 y 33% de proteína cruda. También se encontró que a medida que se elevó el nivel de proteína de la dieta, la REP decreció significativamente. Tomando en cuenta el costo de la proteína en la dieta, se concluye que la alimentación de la gamitana con niveles dietarios de 25 ó 27% de proteína cruda y 2,7 kcal de ED/g, garantizarán su exitoso crecimiento.

  1. Evaluation of nuclear facility decommissioning projects. Three Mile Island Unit 2 reactor building decontamination. Summary status report. Volume 2

    International Nuclear Information System (INIS)

    This document summarizes information relating to decontamination of the Three Mile Island Unit 2 (TMI-2) reactor building. The report covers activities for the period of June 1, 1979 through March 29, 1985. The data collected from activity reports, reactor containment entry records, and other sources were entered into a computerized data system which permits extraction/manipulation of specific information which can be used in planning for recovery from an accident similar to that experienced at TMI-2 on March 28, 1979. This report contains summaries of man-hours, manpower, and radiation exposures incurred during decontamination of the reactor building. Support activities conducted outside of radiation areas are excluded from the scope of this report. Computerized reports included in this document are: a chronological summary listing work performed relating to reactor building decontamination for the period specified; and summary reports for each major task during the period. Each task summary is listed in chronological order for zone entry and subtotaled for the number of personnel entries, exposures, and man-hours. Manually-assembled table summaries are included for: labor and exposures by department and labor and exposures by major activity

  2. Evaluation of nuclear facility decommissioning projects. Three Mile Island Unit 2 reactor building decontamination. Summary status report. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    Doerge, D.H.; Miller, R.L.; Scotti, K.S.

    1986-05-01

    This document summarizes information relating to decontamination of the Three Mile Island Unit 2 (TMI-2) reactor building. The report covers activities for the period of June 1, 1979 through March 29, 1985. The data collected from activity reports, reactor containment entry records, and other sources were entered into a computerized data system which permits extraction/manipulation of specific information which can be used in planning for recovery from an accident similar to that experienced at TMI-2 on March 28, 1979. This report contains summaries of man-hours, manpower, and radiation exposures incurred during decontamination of the reactor building. Support activities conducted outside of radiation areas are excluded from the scope of this report. Computerized reports included in this document are: a chronological summary listing work performed relating to reactor building decontamination for the period specified; and summary reports for each major task during the period. Each task summary is listed in chronological order for zone entry and subtotaled for the number of personnel entries, exposures, and man-hours. Manually-assembled table summaries are included for: labor and exposures by department and labor and exposures by major activity.

  3. Respuesta glucémica e insulinémica a dos fórmulas enterales isocalóricas en pacientes con diabetes mellitus tipo 2

    Directory of Open Access Journals (Sweden)

    D. A. de Luis

    2013-06-01

    Full Text Available Objetivos: El objetivo del presente estudio es comparar la respuesta glucémica e insulinémica de pacientes diabéticos tipo 2 tras la administración oral de 250 ml de dos formulas enterales: una formula especifica (Novasource® Diabet Smartflex® frente a una fórmula isocalórica estándar. Material y métodos: El diseño fue cruzado, recibiendo los pacientes diabéticos (n = 15 de manera aleatoria las dos fórmulas. Se realizó una curva de glucemia e insulinemia en los tiempos 0, 10,20, 30,60, 90, 120,150 y 180 minutos. Las variables analizadas fueron, el área bajo la curva (AUC0-t, la concentración máxima (Cmax, el tiempo en que se alcanza la concentración máxima (Tmax y las concentraciones de los parámetros bioquímicos en cada período del estudio. Resultados: Se estudiaron 11 varones (73.3% y 4 mujeres (26.7%, la edad media fue de 56,9 ± 10,9 años. Los pacientes que recibieron Novasource® Diabet presentan una media menor de AUC0-t, diferencia entre medias de glucemia -4.753,26 mg/min/dl (IC 95%: -7.256,7 a -2.249,82, también presentaron una media de insulinemia significativamente menor de AUC0-t, diferencia de medias: -930,27 uU/min/ml (IC 95%: -1.696,34 a -164,2. La Cmax mostró unas medias de glucemia significativamente menores con la fórmula específica, diferencia de medias -26,89 mg/dl (IC 95% 42,11 a -11,67 e insulinemia, diferencia de medias: -5,39 uU/ml (IC 95%: -10,37 a -1,43. El análisis de Tmax muestra que las medias de glucemia con la fórmula específica son significativamente menores, diferencia de medias -19,82 min (IC 95%: -32,11 a -7,33, sin diferencia significativa en la Tmax de insulinemia. Finalmente el análisis de las concentraciones de glucosa en el total del estudio muestra que el grupo con la formula específica tiene una media menor de glucosa 25,77 mg/dl (IC 95%: 18,29 a 33,25, sucediendo lo mismo con la insulinemia 4,39 U/ml (IC 95%: 0,927 a 7,87. Conclusiones: Los pacientes diabéticos tipo 2

  4. Solubility and properties of saturated solutions in the system Li2MoO4-iso-C5H11OH-H2O at 25 deg C

    International Nuclear Information System (INIS)

    Solubility in the system Li2MoO4-iso-C5H11OH-H2O at 25 deg C was studied by the method of isothermal saturation. It is shown that, when increasing amount of lithium molybdate is added to a mixture of alcohol and water, a noticeable decrease in mutual solubility of initial solvents and stratification of liquid phase into water and alcohol ones take place. Compositions of equilibrium water and alcohol phases, refractive index, dynamic viscosity and specific electric conductivity of saturated solutions in the system studied were determined. Isotherms of specific and mole volumes, kinematic viscosity, equivalent and reduced electric conductivity of the solutions were calculated

  5. Team-building through sailing: effects on health status, job satisfaction and work performance of health care professionals involved in organ and tissue donation.

    Science.gov (United States)

    Ponzin, Diego; Fasolo, Adriano; Vidale, Enrico; Pozzi, Annalaura; Bottignolo, Elisa; Calabrò, Francesco; Rupolo, Giampietro

    2015-01-01

    The aim of this study was to evaluate the effects of a team-building learning project on job satisfaction, psychological wellbeing, and performance of health care workers involved in the process of organ and tissue donation. The project was conducted between June and September 2011 and consisted of two one-day meetings and a one week sailing, involving 20 staff members. GHQ-12, MBI-HSS, and 25 items taken from the Multidimensional Organizational Health Questionnaire (MOHQ) were used to assess health status, burnout, and job satisfaction. Results of the descriptive analyses were expressed as mean ± SD and as counts and percentages; Chi-square test was used to evaluate statistical significance of differences before and after the initiative. 6 (30,0%) participants showed the likelihood to suffering from anxiety and depression (i.e. recognized as 'cases' by the GHQ-12), 3 (15.0%) of them at baseline and 3 (15.0%), different from the previous ones, in the post-intervention. The presence of stress was revealed in 9 (45.0%) and 12 subjects (60.0%) before and after the experience, respectively (6 subjects showed the presence of stress in both circumstances). We documented 4 burnout cases, 3 (15.0%) at baseline and 1 (5.0%) after the experience. Nevertheless, about 80% of the participants showed a high degree ofjob satisfaction, in terms of positive influence of job in the professional satisfaction and of clear satisfaction for the organization, during both evaluation. In respect to 2010, the number of organ donors and that of ocular tissue donors improved of about 16% and 10%, respectively, during the year of the project and in the following year (mean value). We recognize that our team-building project for personnel involved in the stressful and demanding setting of organ and tissue donation, worthwhile and recompensing at the same time, possibly influenced the personal commitment and the quality of job provided. The high level of stress showed by participants should be

  6. 建筑施工企业供应链管理现状及存在的问题%Supply-chain management status and existing problems of building construction enterprise

    Institute of Scientific and Technical Information of China (English)

    史国红

    2011-01-01

    概括了我国建筑施工企业供应链管理现状,根据项目流程总结了目前建筑供应链管理亟待解决的问题,并剖析了其原因,最后提出先进管理手段,以实现企业与供应商之间的互通。%This thesis outlines supply-chain management status of building construction enterprise,summarizes urgent problems needing solving in temporary building supply-chain management according to project procedure,and analyzes its causes.In the end,it proposes advanced management means,with a view to realize mutual connection between enterprise and supplier.

  7. Energy consumptions in existing buildings; Les consommations d'energie des batiments existants

    Energy Technology Data Exchange (ETDEWEB)

    Nuss, St. [Ecole Nationale Superieure des Arts et Industries de Strasbourg, 78 - Saint-Remy-Les-Chevreuse (France)]|[Costic, 78 - Sainte Remy les Chevreuses (France)

    2002-05-01

    This document presents a sectoral analysis of the energy consumptions in existing French buildings: 1) - residential sector: social buildings, private dwellings; 2) - tertiary sector: office buildings, hotels, commercial buildings, school buildings, hospitals; 3) - industry; 4) - general status. (J.S.)

  8. THE CURRENT STATUS OF CITIZENS' ADVISORY COMMITTEES WITH EMPHASIS ON THOSE FOR SCHOOL BUILDING NEEDS IN THE CENTRAL SCHOOLS OF NEW YORK STATE.

    Science.gov (United States)

    MARLOW, FRANK M.

    STATISTICAL INFORMATION ABOUT CITIZENS' ADVISORY COMMITTEES, WITH EMPHASIS ON SCHOOL BUILDING NEEDS, IS PRESENTED. THE STATISTICS WERE OBTAINED FROM QUESTIONNAIRES SENT TO SCHOOL ADMINISTRATORS IN CENTRAL NEW YORK STATE, DISCUSSING SCHOOL ENROLLMENT, DISTANCE FROM CLASS I CITIES, AND THE MAKE-UP OF ADVISORY COMMITTEES AND THEIR FUNCTIONS. (JH)

  9. ViennaNGS: A toolbox for building efficient next- generation sequencing analysis pipelines [v2; ref status: indexed, http://f1000r.es/5mq

    OpenAIRE

    Wolfinger, Michael T.; Jörg Fallmann; Florian Eggenhofer; Fabian Amman

    2015-01-01

    Recent achievements in next-generation sequencing (NGS) technologies lead to a high demand for reuseable software components to easily compile customized analysis workflows for big genomics data. We present ViennaNGS, an integrated collection of Perl modules focused on building efficient pipelines for NGS data processing. It comes with functionality for extracting and converting features from common NGS file formats, computation and evaluation of read mapping statistics, as well as normalizat...

  10. Status Quo of Twice Supplying Water for High Building and Antisepsis Effect of MF-2 Disinfector%高层建筑二次供水的现状及MF-2消毒剂的消毒效果

    Institute of Scientific and Technical Information of China (English)

    刘庆增; 王金兰

    2002-01-01

    Objective To discuss status quo of twice supplying water for high building and validateantisepsis effect of MF - 2 disinfector. Methods By field test and searching reference, discussing thequestions of above - describe. According to state prescriptive method for disinfecting drinking water, vali-dating the antisepsis effect of disinfecting twice supplying water. Results Currently, establishment fortwice supplying water and the quality of the supplying water has some questions. According to the qualityof twice supplying water, acceding to some MF - 2 disinfector to disinfect, it will achieve the standard ofdrinking water. Conclusion Circumstance management department and sanitation supervise departmentshould smeliorate and manage the quality of twice supplying water, and insure the safety of using drinkingwater. So MF - 2 disinfector may replace contain chlorin disinfector to disinfect twice supplying water.

  11. The Status Quo of Flue Gas Treatment and Ultralow Emission Schemes for Building Ceramic Industry%建筑陶瓷烟气治理现状及超低排放方案探讨

    Institute of Scientific and Technical Information of China (English)

    罗小根; 崔宜祥; 尹海滨; 许珊珊; 周伟安; 田思源

    2015-01-01

    The emission status quo, treatment technologies, and existing problems of lfue gas from building ceramic industry are introduced. The particle characteristics of dust from spray dryer as well as in lfue gas from kiln are analyzed. Then, the ultralow lfue gas emission goals for the industry along with two technical schemes to achieve them are proposed..%介绍了当前建筑陶瓷工业烟气排放现状、治理技术及存在的问题,并分析了陶瓷工业喷雾干燥塔及窑炉烟气粉尘的特性。同时,根据当前的排放现状及治理技术,提出了陶瓷工业烟气超低排放目标,并提出了两种适用于建筑陶瓷工业烟气超低排放治理工艺方案。

  12. Reactor building

    International Nuclear Information System (INIS)

    The whole reactor building is accommodated in a shaft and is sealed level with the earth's surface by a building ceiling, which provides protection against penetration due to external effects. The building ceiling is supported on walls of the reactor building, which line the shaft and transfer the vertical components of forces to the foundations. The thickness of the walls is designed to withstand horizontal pressure waves in the floor. The building ceiling has an opening above the reactor, which must be closed by cover plates. Operating equipment for the reactor can be situated above the building ceiling. (orig./HP)

  13. Building America

    Energy Technology Data Exchange (ETDEWEB)

    Brad Oberg

    2010-12-31

    IBACOS researched the constructability and viability issues of using high performance windows as one component of a larger approach to building houses that achieve the Building America 70% energy savings target.

  14. Solar building

    OpenAIRE

    Zhang, Luxin

    2014-01-01

    In my thesis I describe the utilization of solar energy and solar energy with building integration. In introduction it is also mentioned how the solar building works, trying to make more people understand and accept the solar building. The thesis introduces different types of solar heat collectors. I compared the difference two operation modes of solar water heating system and created examples of solar water system selection. I also introduced other solar building applications. It is conv...

  15. Building 2000

    International Nuclear Information System (INIS)

    This is the first volume of Building 2000, a pilot project of the Commission's R and D-programme 'Solar Energy Applications to Buildings' with the purpose of encouraging the adoption of solar architecture in large buildings. In this first rich illustrated volume the results of the design studies illustrating passive solar architecture in buildings in the European Community are presented in particular for the building categories as mentioned in the subtitle. In a second volume, a similar series of studies is presented for the building categories: office buildings, public buildings and hotels and holiday complexes. Several Design Support Workshops were organized during the Building 2000 programme during which Building 2000 design teams could directly exchange ideas with the various design advice experts represented at these workshops. In the second part of the Building 2000 final report a summary of a selection of many reports is presented (15 papers), as produced by Design Support experts. Most of the design support activities resulted in changes of the various designs, as have been reported by the design teams in the brochures presented in the first part of this book. It is to be expected that design aids and simulation tools for passive solar options, daylighting concepts, comfort criteria etc., will be utilized more frequently in the future. This will result in a better exchange of information between the actual design practitioners and the European R and D community. This technology transfer will result in buildings with a higher quality with respect to energy and environmental issues

  16. Building Energy Monitoring and Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Tianzhen; Feng, Wei; Lu, Alison; Xia, Jianjun; Yang, Le; Shen, Qi; Im, Piljae; Bhandari, Mahabir

    2013-06-01

    This project aimed to develop a standard methodology for building energy data definition, collection, presentation, and analysis; apply the developed methods to a standardized energy monitoring platform, including hardware and software, to collect and analyze building energy use data; and compile offline statistical data and online real-time data in both countries for fully understanding the current status of building energy use. This helps decode the driving forces behind the discrepancy of building energy use between the two countries; identify gaps and deficiencies of current building energy monitoring, data collection, and analysis; and create knowledge and tools to collect and analyze good building energy data to provide valuable and actionable information for key stakeholders.

  17. DUMAND status report

    International Nuclear Information System (INIS)

    DUMAND is a project to build a large deep underwater laboratory for the study of high energy neutrinos from extrasolar sources. The stage 11 array -consisting of 216 optical modules covering an effective area of about 20 000 m2 for neutrinos with energies above 500 GeV/c - is under construction. The fibre optic cable for data transmission has been deployed successfully. A report on the present status of the experiment is given. (orig.)

  18. Building envelope for New Buildings and Energy Renovation of Existing Buildings. Project results

    DEFF Research Database (Denmark)

    Rudbeck, Claus Christian; Rose, Jørgen; Esbensen, Peter Kjær; Svendsen, Sv Aa Højgaard

    1999-01-01

    facts, a group of scientists at the Department of Buildings and Energy, Technical University of Denmark, have started a research project to develop better solutions for new building and energy renovation.The publication report the status after the first 3 year of the Building Envelope Project with......At the energy conference in 1995, Denmark agreed on reducing the total CO2-emission by 20%. To achieve this goal, it is necessary to increase thermal insulation thickness both in new and retrofitted buildings.This will, for both cases, impose a series of building physics problems, as the knowledge...... emphasis on the following subjects:Scientific basis for calculation programs, Development of calculationsmethods for heat transfer, Development of new building envelope components, Roofing system based on wooden roof elements, Roofing system with drying properties, Moisture uptake and drying from brick...

  19. Building 2000

    International Nuclear Information System (INIS)

    This is the second volume of Building 2000, a pilot project of the Commission's R and D-programme 'Solar Energy Applications to Buildings' with the purpose of encouraging the adoption of solar architecture in large buildings. In this second rich illustrated volume the results of the design studies illustrating passive solar architecture in buildings in the European Community are presented in particular for the building categories as mentioned in the subtitle. In the first volume, a similar series of studies is presented for the building categories: schools, laboratories and universities, and sports and educational centres. Several Design Support Workshops were organized during the Building 2000 programme during which Building 2000 design teams could directly exchange ideas with the various design advice experts represented at these workshops. In the second part of the Building 2000 final report a summary of a selection of many reports is presented (11 papers), as produced by Design Support experts. Most of the design support activities resulted in changes of the various designs, as have been reported by the design teams in the brochures presented in the first part of this book. It is to be expected that design aids and simulation tools for passive solar options, daylighting concepts, comfort criteria etc., will be utilized more frequently in the future. This will result in a better exchange of information between the actual design practitioners and the European R and D community. This technology transfer will result in buildings with a higher quality with respect to energy and environmental issues

  20. Laboratory Building.

    Energy Technology Data Exchange (ETDEWEB)

    Herrera, Joshua M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-03-01

    This report is an analysis of the means of egress and life safety requirements for the laboratory building. The building is located at Sandia National Laboratories (SNL) in Albuquerque, NM. The report includes a prescriptive-based analysis as well as a performance-based analysis. Following the analysis are appendices which contain maps of the laboratory building used throughout the analysis. The top of all the maps is assumed to be north.

  1. Status quo of AIDS control institutions and their capacity building in Health Ⅸ Project provinces/regions%卫九项目省(自治区)艾滋病防治机构和能力建设现状

    Institute of Scientific and Technical Information of China (English)

    项炯; 王德斌; 杨续兵; 洪倩

    2011-01-01

    Objective To analyze status quo of AIDS control institutions and their capacity building in Health Ⅸ Project provinces/regions. Methods A descriptive analysis was made of the data obtained from the final evaluation of the AIDS/STD control subcomponent of Health Ⅸ Project. Results First, in the past years, AIDS control leading groups were set up in project provinces/regions, cities and counties and the number of departments participating in the leading groups was increasing year after year. Second, various types of equipment and devices which were worth ten millions of yuan were secured for management and disease control purpose, and as a result, the network of AIDS diagnosis and screening at all levels was greatly improved and more HIV surveillance points were placed.Third, information technology was applied in an increasingly extensive way as a tool to verify HIV related testing and management in CDCs, hospitals and laboratories of blood centers. Fourth, managerial and technical staffs working for AIDS/STDs control in project provinces/regions improved their knowledge and skills by participating in conferences, training courses and study tours ( exceeding totally 280 000 persons/days). Conclusion Remarkable improvement has been achieved in AIDS control institutions in relation to their capacity building in Health Ⅸ Project provinces/ regions, which will greatly push forward AIDS control work in other related provinces/regions.%目的 了解卫九项目省(自治区,下同)艾滋病防治机构与能力建设现状.方法 利用卫九项目艾滋病(AIDS)/性病(STD)预防控制子项目终末评估调查数据进行描述性分析.结果 近年来,项目省、市、县各级全面成立了艾滋病防治领导小组,参与领导小组的成员部门数逐年上升;项目省得到了价值数千万元的各类防治与管理设备,各级艾滋病确证与初筛实验室网络建设得到了很好的发展,艾滋病病毒(HIV)监测哨点设置明显增多;

  2. Building Energy Monitoring and Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Tianzhen; Feng, Wei; Lu, Alison; Xia, Jianjun; Yang, Le; Shen, Qi; Im, Piljae; Bhandari, Mahabir

    2013-06-01

    U.S. and China are the world’s top two economics. Together they consumed one-third of the world’s primary energy. It is an unprecedented opportunity and challenge for governments, researchers and industries in both countries to join together to address energy issues and global climate change. Such joint collaboration has huge potential in creating new jobs in energy technologies and services. Buildings in the US and China consumed about 40% and 25% of the primary energy in both countries in 2010 respectively. Worldwide, the building sector is the largest contributor to the greenhouse gas emission. Better understanding and improving the energy performance of buildings is a critical step towards sustainable development and mitigation of global climate change. This project aimed to develop a standard methodology for building energy data definition, collection, presentation, and analysis; apply the developed methods to a standardized energy monitoring platform, including hardware and software, to collect and analyze building energy use data; and compile offline statistical data and online real-time data in both countries for fully understanding the current status of building energy use. This helps decode the driving forces behind the discrepancy of building energy use between the two countries; identify gaps and deficiencies of current building energy monitoring, data collection, and analysis; and create knowledge and tools to collect and analyze good building energy data to provide valuable and actionable information for key stakeholders.

  3. Building Procurement

    DEFF Research Database (Denmark)

    Andersson, Niclas

    2007-01-01

    ‘The procurement of construction work is complex, and a successful outcome frequently elusive’. With this opening phrase of the book, the authors take on the challenging job of explaining the complexity of building procurement. Even though building procurement systems are, and will remain, complex...... despite this excellent book, the knowledge, expertise, well-articulated argument and collection of recent research efforts that are provided by the three authors will help to make project success less elusive. The book constitutes a thorough and comprehensive investigation of building procurement, which......, which gives the book a challenging contribution to the existing body of knowledge....

  4. Net Zero Energy Buildings

    DEFF Research Database (Denmark)

    Marszal, Anna Joanna; Bourrelle, Julien S.; Musall, Eike;

    2010-01-01

    The international cooperation project IEA SHC Task 40 / ECBCS Annex 52 “Towards Net Zero Energy Solar Buildings”, attempts to develop a common understanding and to set up the basis for an international definition framework of Net Zero Energy Buildings (Net ZEBs). The understanding of such buildings...... and how the Net ZEB status should be calculated differs in most countries. This paper presents an overview of Net ZEBs energy calculation methodologies proposed by organisations representing eight different countries: Austria, Canada, Denmark, Germany, Italy, Norway, Switzerland and the USA. The...... different parameters used in the calculations are discussed and the various renewable supply options considered in the methodologies are summarised graphically. Thus, the paper helps to understand different existing approaches to calculate energy balance in Net ZEBs, highlights the importance of variables...

  5. Reactor building

    International Nuclear Information System (INIS)

    The present invention concerns a structure of ABWR-type reactor buildings, which can increase the capacity of a spent fuel storage area at a low cost and improved earthquake proofness. In the reactor building, the floor of a spent fuel pool is made flat, and a depth of the pool water satisfying requirement for shielding is ensured. In addition, a depth of pool water is also maintained for a equipment provisionally storing pool for storing spent fuels, and a capacity for a spent fuel storage area is increased by utilizing surplus space of the equipment provisionally storing pool. Since the flattened floor of the spent fuel pool is flushed with the floor of the equipment provisionally storing pool, transfer of horizontal loads applied to the building upon occurrence of earthquakes is made smooth, to improve earthquake proofness of the building. (T.M.)

  6. Building Languages

    Science.gov (United States)

    ... family's native language) is taught as the child's second language through reading, writing, speech, and use of residual ... that parents can use to help their child learn language. There are many types of building blocks, and ...

  7. Developing green building policy in Hong Kong

    OpenAIRE

    Fung, Lok-yan, Esther; 馮樂恩

    2014-01-01

    Desk-top research found that the performance of green building development in Hong Kong has lagged behind other countries or cities of similar international status. The main reason for that is the lack of green building policy to coordinate the existing measures. Hence, this dissertation aims to fill the gap by finding out whether green building policy should be implemented in Hong Kong and what instruments or tools should be included in the policy if it is formulated. Further to the focu...

  8. Iso-C臂三维导航系统指导下的脊柱侧弯椎弓根钉内固定:问题与优势%Pedicle screw fixation for scoliosis using Iso-C arm three-dimensional navigation:problems and advantages

    Institute of Scientific and Technical Information of China (English)

    陈强; 张怡元; 林妙阔; 冯尔宥

    2015-01-01

    背景:由于脊柱侧弯患者脊柱解剖结构的变异、椎体旋转、椎体缺如、椎管变形等异常情况,椎弓根螺钉一旦置入发生偏差,即可导致灾难性结果。近年来随着椎弓根螺钉的广泛应用和计算机导航的不断发展,使脊柱侧弯修复手术更加精确、安全。  目的:综述Iso-C臂三维导航系统指导脊柱侧弯椎弓根钉置入内固定存在的问题及优势。  方法:由第一作者检索至2012年12月为止 PubMed数据(http://www.ncbi.nlm.nih.gov/PubMed)及CNKI中国期刊全文数据库(http://www.cnki.net/),以“计算机导航,脊柱侧弯,椎弓根钉”为检索词,检索摘要内同时包含上述检索词的文献。共检索到50多篇相关文献,13篇文献符合纳入标准。  结果与结论:应用 Iso-C 臂三维导航系统进行脊柱侧弯椎弓根螺钉置入内固定具有显著优势。它充分结合了CT三维导航和术中透视导航的优点,可快速、准确的采集术中影像数据,通过影像实时显示,从而确保修复手术的安全。Iso-C臂三维导航其自动注册的功能无疑提高了修复效率和精确性,帮助术者以更加精确、安全的方式进行各种复杂的脊柱侧弯修复手术。%BACKGROUND:Due to variation of spinal anatomic structure, vertebral body rotation, absence of vertebral body, and spinal canal deformation in patients with scoliosis, the deviation of pedicle screw placement can induce catastrophic results. Recently, with the wide application of pedicle screw and the continuous development of computer navigation, scoliosis surgery becomes more accurate and safe. OBJECTIVE:To review the existing problems and advantages of Iso-C arm three-dimensional (3D) navigation system for guiding internal fixation of pedicle screw implantation in the treatment of scoliosis. METHODS: The first author searched PubMed (http://www.ncbi.nlm.nih.gov/PubMed) and CNKI (http

  9. Investigation and Analysis on Energy-saving Status of Existing Buildings in Hainan%海南地区既有建筑节能现状调研分析

    Institute of Scientific and Technical Information of China (English)

    费良旭; 张磊; 孟庆林

    2013-01-01

    本文调研了海南地区住宅、办公、酒店、商业、综合、教育、医院等各类既有建筑的基本信息、围护结构构成形式及空调设备的性能系数等,并运用数理统计方法对所得数据进行了统计分析,得出了海南地区既有建筑节能现状的特征.结果显示,海南地区既有建筑中公共建筑和居住建筑各占一半左右,其中公共建筑类型以办公和酒店建筑居多;既有建筑外墙的主体材料多采用加气混凝土,粘土实心砖的使用比例约占20%;近1/3的屋顶没有任何隔热措施;普通铝合金窗框搭配单层普通玻璃外窗形式占60%以上,外窗的遮阳形式以内遮阳为主,外窗方面具有较大的节能潜力.此外,海南地区空调机组制冷性能系数达不到《海南省公共建筑节能设计标准》(DBJ 03-2006)的占48.4%,空调设备节能的空间较大.本文通过分析找出了海南地区既有建筑节能改造工作的重点所在,为研究相应的改造措施打下了基础.%In this paper,the basic information of various existing buildings such as residential buildings,office buildings,hotels,business buildings,comprehensive buildings,education buildings,hospitals,etc.in Hainan was investigated and analyzed,including structural forms of building envelope and performance coefficients of air-conditioning equipment,statistic analysis on the acquired data was performed through mathematical statistics method,and the characteristics of energy-saving conditions of existing buildings in Hainan were presented.The results shown that existing buildings in Hainan were composed of public buildings and residential buildings,which were half and half,office buildings and hotels were the majority among public buildings,major materials of external walls of existing buildings were generally aerated concrete and proportion of clay solid brick was about 20%,about 1/3 of roofs were not provided with thermal insulation measures at all,60

  10. 河南省高校健美课程建设现状分析%Analysis on Status of Body-building Course in Colleges in Henan Province ZHANG Lei

    Institute of Scientific and Technical Information of China (English)

    张磊

    2014-01-01

    This thesis gives analysis to the coverage rate,content and forms of body building courses,finds problems and gives suggestion on how to make better construction on body building courses,in order to provide reference on speeding up the development of body-building courses and improue the body-building teaching in Henan province.%对我省高校健美课开课率、教学内容、教学形式等方面进行分析研究,找出存在的问题并提出有效提高健美课程建设的方案,旨在为调整课程结构和深化学校体育改革提供参考依据,以促进我省高校健美教学的快速发展。

  11. Stock Status

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — These data inform the public of the most recent stock status for all stocks (FSSI and non-FSSI) in the fishery management unit contained in a fishery managment...

  12. DUMAND status report

    International Nuclear Information System (INIS)

    DUMAND is a project to build a large deep underwater laboratory for the study of high energy neutrinos from extra solar sources. The stage II array -consisting of 216 optical modules covering an effective area of about 20000 m2 for neutrinos with energies above 500 GeV/c - is under construction. The complete detector will have an angular resolution of around 1 degree. The fibre optic cable for data transmission has been deployed successfully. A report on the present status of the experiment as well as a short outlook to the next generation detectors is given. (author). 5 figs., 6 refs

  13. Building Procurement

    DEFF Research Database (Denmark)

    Andersson, Niclas

    2007-01-01

    ‘The procurement of construction work is complex, and a successful outcome frequently elusive’. With this opening phrase of the book, the authors take on the challenging job of explaining the complexity of building procurement. Even though building procurement systems are, and will remain, complex...... despite this excellent book, the knowledge, expertise, well-articulated argument and collection of recent research efforts that are provided by the three authors will help to make project success less elusive. The book constitutes a thorough and comprehensive investigation of building procurement, which...... evolves from a simple establishment of a contractual relationship to a central and strategic part of construction. The authors relate to cultural, ethical and social and behavioural sciences as the fundamental basis for analysis and understanding of the complexity and dynamics of the procurement system...

  14. Competence Building

    DEFF Research Database (Denmark)

    Borrás, Susana; Edquist, Charles

    The main question that guides this paper is how governments are focusing (and must focus) on competence building (education and training) when designing and implementing innovation policies. With this approach, the paper aims at filling the gap between the existing literature on competences on the...... one hand, and the real world of innovation policy-making on the other, typically not speaking to each other. With this purpose in mind, this paper discusses the role of competences and competence-building in the innovation process from a perspective of innovation systems; it examines how governments...... and public agencies in different countries and different times have actually approached the issue of building, maintaining and using competences in their innovation systems; it examines what are the critical and most important issues at stake from the point of view of innovation policy, looking...

  15. Building Bridges

    DEFF Research Database (Denmark)

    The report Building Bridges adresses the questions why, how and for whom academic audience research has public value, from the different points of view of the four working groups in the COST Action IS0906 Transforming Audiences, Transforming Societies – “New Media Genres, Media Literacy and Trust...... in the Media”, “Audience Interactivity and Participation”, “The Role of Media and ICT Use for Evolving Social Relationships” and “Audience Transformations and Social Integration”. Building Bridges is the result of an ongoing dialogue between the Action and non-academic stakeholders in the field of audience...

  16. Building energy efficiency in rural China

    International Nuclear Information System (INIS)

    Rural buildings in China now account for more than half of China's total building energy use. Forty percent of the floorspace in China is in rural villages and towns. Most of these buildings are very energy inefficient, and may struggle to provide for basic needs. They are cold in the winter, and often experience indoor air pollution from fuel use. The Chinese government plans to adopt a voluntary building energy code, or design standard, for rural homes. The goal is to build on China's success with codes in urban areas to improve efficiency and comfort in rural homes. The Chinese government recognizes rural buildings represent a major opportunity for improving national building energy efficiency. The challenges of rural China are also greater than those of urban areas in many ways because of the limited local capacity and low income levels. The Chinese government wants to expand on new programs to subsidize energy efficiency improvements in rural homes to build capacity for larger-scale improvement. This article summarizes the trends and status of rural building energy use in China. It then provides an overview of the new rural building design standard, and describes options and issues to move forward with implementation. - Highlights: • Building energy use is larger in rural China than in cities. • Rural buildings are very energy intensive, and energy use is growing with incomes. • A new design standard aims to help rural communities build more efficiently. Important challenges remain with implementation

  17. Sustainable Buildings

    DEFF Research Database (Denmark)

    Tommerup, Henrik M.; Elle, Morten

    The scientific community agrees that: all countries must drastically and rapidly reduce their CO2 emissions and that energy efficient houses play a decisive role in this. The general attitude at the workshop on Sustainable Buildings was that we face large and serious climate change problems that...

  18. Compliance status

    Energy Technology Data Exchange (ETDEWEB)

    Black, D.G.

    1995-06-01

    This section of the 1994 Hanford Site Environmental Report summarizes the activities conducted to ensure that the Hanford Site is in compliance with federal environmental protection statutes and related Washington State and local environmental protection regulations and the status of Hanford`s compliance with these requirements. Environmental permits required under the environmental protection regulations are discussed under the applicable statute.

  19. Administrative building

    OpenAIRE

    Vokatá, Kateřina

    2015-01-01

    The task of my master´s thesis was to work up a project and a check of a bearing steel construction the multi-storey office building with a garage in Brno. The building is composed of five storey office section and two storey of garage. Ground dimension of administrative part is 38,8m x 35m with distance of pillars 7m,6m and 6,4m. The structural height of floor is 3,5m.Garage is designed with dimensions 36m x 24,8m with structural height of floor 3,5m. Distance of pillars is 5,6m, 6,4m and 7,...

  20. Building economics

    DEFF Research Database (Denmark)

    Pedersen, D.O.(red.)

    Publikationen er på engelsk. Den omfatter alle indlæg på det fjerde internationale symposium om byggeøkonomi, der blev arrangeret af SBI for det internationale byggeforskningsråd CIB. De fem bind omhandler: Methods of Economic Evaluation, Design Optimization, Ressource Utilization, The Building...... Market og Economics and Technological Forecasting in Construction. Et indledende bind bringer statusrapporter for de fem forskningsområder, og det sidste bind sammenfatter debatten på symposiet....

  1. Model Building

    OpenAIRE

    Frampton, Paul H.

    1997-01-01

    In this talk I begin with some general discussion of model building in particle theory, emphasizing the need for motivation and testability. Three illustrative examples are then described. The first is the Left-Right model which provides an explanation for the chirality of quarks and leptons. The second is the 331-model which offers a first step to understanding the three generations of quarks and leptons. Third and last is the SU(15) model which can accommodate the light leptoquarks possibly...

  2. Building Inclusion

    OpenAIRE

    Jeanet Kullberg; Isik Kulu-Glasgow

    2009-01-01

    The social inclusion of immigrants and ethnic minorities is a central issue in many European countries. Governments face challenges in ensuring housing for immigrants, delivering public services, promoting neighbourhood coexistence and addressing residential segregation. The Building Inclusion project, sponsored by the European Commission, enables EU member states to exchange experiences relating to the social inclusion of vulnerable groups. Its special focus is on housing access and housing ...

  3. Status seminar 1997: Energetic improvement of buildings, with particular regard to large-panel structures in East Germany. Proceedings; Statusseminar 1997: Energetische Verbesserung der Bausubstanz mit Schwerpunkt energiegerechte Sanierung von in industrieller Bauweise errichteten Wohnbauten der neuen Bundeslaender. Tagungsband

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This R and D report deals with the redevelopment of large-panel buildings, especially apartment houses and school buildings, with a view to energy conservation. Measures carried out range from thermal insulation over the fitting of new heating systems and improved ventilation systems to the automatic control of space air temperature. Further topics concern costs and the economy of redevelopment measures. Moreover, information on thermal energy consumption and energy conservation potentials is given. Modernization of school buildings includes lighting systems. 23 individual contributions are listed in the energy database. (MSK) [Deutsch] Es werden Forschungs-und Entwicklungsergebnisse von Sanierungsprojekten an Plattenbauten, v.a. Wohnhaeuser und Schulgebaeude, zur Energieeinsparung vorgestellt. Die durchgefuehrten Massnahmen reichen von Waermedaemmung ueber Einbau neuer Heizungssysteme, verbesserte Lueftungsanlagen bis zur Automatisierung der Raumtemperaturregelung. Weitere Themen befassen sich mit den Kosten und der Wirtschaftlichkeit der Sanierungsmassnahmen. Ausserdem werden Angaben zum Heizenergieverbrauch und den Energieeinsparungspotentialen gemacht. Bei der Sanierung von Schulgebaeude werden lichttechnische Anlagen miteinbezogen. Fuer die Datenbank Energy wurden 23 Artikel einzeln aufgenommen.

  4. Status Epilepticus.

    Science.gov (United States)

    Seinfeld, Syndi; Goodkin, Howard P; Shinnar, Shlomo

    2016-01-01

    Although the majority of seizures are brief and cause no long-term consequences, a subset is sufficiently prolonged that long-term consequences can result. These very prolonged seizures are termed "status epilepticus" (SE) and are considered a neurological emergency. The clinical presentation of SE can be diverse. SE can occur at any age but most commonly occurs in the very young and the very old. There are numerous studies on SE in animals in which the pathophysiology, medication responses, and pathology can be rigorously studied in a controlled fashion. Human data are consistent with the animal data. In particular, febrile status epilepticus (FSE), a form of SE common in young children, is associated with injury to the hippocampus and subsequent temporal lobe epilepsy (TLE) in both animals and humans. PMID:26931807

  5. 105-C Building characterization survey data report

    International Nuclear Information System (INIS)

    This report is a compilation of the 105-C Facility Characterization Survey data collected during the period of July 1, 1994, through September 30, 1994. The scope of the report is limited to the characterization of the 105-C Facility and surrounding site. Conclusions and recommendations regarding courses of future action are beyond the scope of this report. The survey data in this report reflects the current conditions and status of the 105-C Building, and is intended to be used in support of future decontamination and decommissioning activities. The survey was organized and implemented to evaluate the four parameters relating to the current condition of the facility. These parameters concern the physical conditions of the 105-C Building from a personnel safety standpoint; the radiological status throughout the building; identification of the hazardous materials located in the building; and identification of subsurface obstacles left in the path of proposed excavations

  6. Being in "Bad" Company: Power Dependence and Status in Adolescent Susceptibility to Peer Influence

    Science.gov (United States)

    Vargas, Robert

    2011-01-01

    Theories of susceptibility to peer influence have centered on the idea that lower status adolescents are likely to adopt the behaviors of high status adolescents. While status is important, social exchange theorists have shown the value of analyzing exchange relations between actors to understand differences in power. To build on status-based…

  7. Of Status and Suits: Personal Space Invasions in an Administrative Setting.

    Science.gov (United States)

    Rosenfeld, Paul; And Others

    1987-01-01

    Examined whether status would affect avoidance of personal space invasions. Drinking behavior of male passersby at water fountain in administration building was recorded while either low status, high status, or no confederate stood near fountain. Results showed a significantly lower rate of drinking when high status confederate stood nearby than…

  8. Tevatron status

    International Nuclear Information System (INIS)

    The Fermilab Tevatron is both the world's highest energy accelerator system and first large-scale superconducting synchrotron. Since Tevatron commissioning in July 1983, the accelerator has operated in 1984, 1985 and 1987 with extracted beams of 800 GeV for three runs of fixed target physics, and in 1987, and 1988, with proton-antiproton colliding beams at 900 /times/ 900 GeV. This paper will focus on the collider operation of the Tevatron: its present status and the outlook for its longer-term future evolution. 18 refs., 3 figs., 2 tabs

  9. Current Status of the Build Systems of Packages in Different Distributions of GNU/Linux Estado actual de los sistemas de construcción de paquetes en diferentes distribuciones de GNU/Linux

    Directory of Open Access Journals (Sweden)

    Dariem Pérez Herrera

    2012-09-01

    Full Text Available

    In this paper, the various systems and tools for building package repositories used by the different distributions of GNU/Linux are analyzed, with the aim of studying features that may be useful given the need for an own system. This will divide these into two groups: the tools for the construction of individual packages and the build systems of package repositories. The first group was studied because they are part of the components of the second group. The tools and systems that are discussed are those used by the distributions Fedora, openSUSE, Debian and Ubuntu have these stable development cycles and be among the most widespread in the field of free operating systems. The tools studied in the first group are: Mock, sbuild and pbuilder. The build systems of packages studied and grouped in the second group are: Koji, Open Build Service, buildd and Soyuz. From each system are studied the architecture, components, programming languages used, security and distinctive features. Closure is met by selecting the best characteristics these systems present that can be imitated, proposing components to be re-used and some other aspects not implemented in studied systems but which are of great interest for the new own system to be developed.

    En este trabajo se analizan los varios sistemas y herramientas de construcción de repositorios de paquetes usados por las distintas distribuciones de GNU/Linux con el objetivo de estudiar características que puedan ser útiles dada la necesidad de contar con un sistema propio. Para ello se dividen estos en dos grupos: las herramientas para la construcción de paquetes individuales y los sistemas de

  10. Estado actual de los sistemas de construcción de paquetes en diferentes distribuciones de GNU/Linux Current Status of the Build Systems of Packages in Different Distributions of GNU/Linux

    Directory of Open Access Journals (Sweden)

    Héctor Pérez Baranda

    2012-09-01

    Full Text Available En este trabajo se analizan los varios sistemas y herramientas de construcción de repositorios de paquetes usados por las distintas distribuciones de GNU/Linux con el objetivo de estudiar características que puedan ser útiles dada la necesidad de contar con un sistema propio. Para ello se dividen estos en dos grupos: las herramientas para la construcción de paquetes individuales y los sistemas de construcción de repositorios de paquetes. Las herramientas y sistemas que se analizan son los utilizados por las distribuciones Fedora, openSUSE, Debian y Ubuntu por contar estas con ciclos de desarrollo estables y estar entre las más difundidas en el ámbito de los sistemas operativos libres. Las herramientas estudiadas en el primer grupo son: Mock, sbuild y pbuilder. Los sistemas de construcción de paquetes estudiados y agrupados en el segundo grupo son: Koji, Open Build Service, buildd y Soyuz. De cada sistema se estudia su arquitectura, componentes, lenguajes de programación empleados, seguridad y características distintivas. Se concluye haciendo una selección de las mejores características presentes en estos sistemas que pudieran imitarse, proponiendo componentes para su reutilización, así como algunos aspectos que no son implementados en los sistemas estudiados pero que son de gran interés para el sistema propio que se desea desarrollar.In this paper, the various systems and tools for building package repositories used by the different distributions of GNU/Linux are analyzed, with the aim of studying features that may be useful given the need for an own system. This will divide these into two groups: the tools for the construction of individual packages and the build systems of package repositories. The first group was studied because they are part of the components of the second group. The tools and systems that are discussed are those used by the distributions Fedora, openSUSE, Debian and Ubuntu have these stable development cycles

  11. Existing buildings

    DEFF Research Database (Denmark)

    Gram-Hanssen, Kirsten

    2014-01-01

    their homes. These policy measures include building regulations, energy tax and different types of incentives and information dissemination. The conclusion calls for new and innovative policy measures to cope with the realities of renovations of owner-occupied houses and how energy efficiency......This paper deals with the energy consumption of existing owner-occupied detached houses and the question of how they can be energy renovated. Data on the age of the Danish housing stock, and its energy consumption is presented. Research on the potential for energy reductions in the Danish housing...... sector is discussed, and it is shown that there is a huge potential for reductions. It is a well-known problem that even if there are relevant technical means and even if it is economically feasible, the majority of house owners do not energy renovate their homes. This paper intends to address what can...

  12. Integrating Responsive Building Elements in Buildings

    DEFF Research Database (Denmark)

    Haase, Matthias; Amato, Alex; Heiselberg, Per

    2006-01-01

    There is a global need for a more sustainable building development. About 50% of energy is used in buildings indicating that buildings provide a considerable potential for operational energy savings. Studies were conducted with the following objectives: to perform a state-of-the-art review of...... responsive building elements, of integrated building concepts and of environmental performance assessment methods to improve and optimize responsive building elements to develop and optimize new building concepts with integration of responsive building elements, HVAC-systems as well as natural and renewable...... energy strategies to develop guidelines and procedures for estimation of environmental performance of responsive building elements and integrated building concepts This paper introduces the ideas of this collaborative work and discusses its usefulness for Hong Kong and China. Special focus was put on the...

  13. Photovoltaics in buildings - international market and state of the art

    International Nuclear Information System (INIS)

    The author examines the use of PV technology in buildings and stresses the importance of PV integration into the architectural design. The status of European collaboration is briefly reviewed with emphasis on IEA Task VII: PV in the built environment

  14. Building Bridges across Sectors and Scales: Exploring Systemic Solutions towards A Sustainable Management of Land —Experiences from 4th Year Status Conference on Research for Sustainable Land Management

    Directory of Open Access Journals (Sweden)

    Annegret Repp

    2015-04-01

    Full Text Available Interacting land use demands and competing interests originating from fields such as agriculture, housing, mobility and nature conservation call for integrated governance approaches that incorporate disciplinary perspectives and arbitrate between them. The German research program “Sustainable Land Management” targets this challenge and provides an umbrella for a number of regional projects involving transdisciplinary system-oriented approaches to sustainable land use, connecting researchers and practitioners. This research note gives an insight into the experiences presented at the program’s fourth year status conference, held in October 2014 in Berlin. It focuses on cross-scalar and cross-sectoral approaches to governing urban-rural interdependencies of land use and scrutinizes debates on how to implement and disseminate project results.

  15. Building energy analysis tool

    Science.gov (United States)

    Brackney, Larry; Parker, Andrew; Long, Nicholas; Metzger, Ian; Dean, Jesse; Lisell, Lars

    2016-04-12

    A building energy analysis system includes a building component library configured to store a plurality of building components, a modeling tool configured to access the building component library and create a building model of a building under analysis using building spatial data and using selected building components of the plurality of building components stored in the building component library, a building analysis engine configured to operate the building model and generate a baseline energy model of the building under analysis and further configured to apply one or more energy conservation measures to the baseline energy model in order to generate one or more corresponding optimized energy models, and a recommendation tool configured to assess the one or more optimized energy models against the baseline energy model and generate recommendations for substitute building components or modifications.

  16. RHIC status

    International Nuclear Information System (INIS)

    The design and construction status of the Relativistic Heavy Ion Collider, RHIC, which is in the seventh year of a nine year construction cycle, is discussed. Those novel performance features of a heavy ion collider that are distinct from hadron colliders in general are noted. These features are derived from the experimental requirements of operation with a variety of ion species over a wide energy range, including collisions between protons and ions, and between ions of unequal energies. Section 1 gives a brief introduction to the major parameters and overall layout of RHIC. A review of the superconducting magnet program is given in Section 2. Activities during the recent Sextant Test are briefly reviewed in Section 3. Finally, Section 4 presents the plans for RHIC commissioning in 1999

  17. Building America

    Energy Technology Data Exchange (ETDEWEB)

    Brad Oberg

    2010-12-31

    Builders generally use a 'spec and purchase' business management system (BMS) when implementing energy efficiency. A BMS is the overall operational and organizational systems and strategies that a builder uses to set up and run its company. This type of BMS treats building performance as a simple technology swap (e.g. a tank water heater to a tankless water heater) and typically compartmentalizes energy efficiency within one or two groups in the organization (e.g. purchasing and construction). While certain tools, such as details, checklists, and scopes of work, can assist builders in managing the quality of the construction of higher performance homes, they do nothing to address the underlying operational strategies and issues related to change management that builders face when they make high performance homes a core part of their mission. To achieve the systems integration necessary for attaining 40% + levels of energy efficiency, while capturing the cost tradeoffs, builders must use a 'systems approach' BMS, rather than a 'spec and purchase' BMS. The following attributes are inherent in a systems approach BMS; they are also generally seen in quality management systems (QMS), such as the National Housing Quality Certification program: Cultural and corporate alignment, Clear intent for quality and performance, Increased collaboration across internal and external teams, Better communication practices and systems, Disciplined approach to quality control, Measurement and verification of performance, Continuous feedback and improvement, and Whole house integrated design and specification.

  18. Building trust

    International Nuclear Information System (INIS)

    'Activate' is the energy magazine for secondary schools and is part of the Education Programme which is managed on behalf of the British Nuclear Industry Forum by AEA Technology. activate is the flagship communication device between the British Nuclear Industry Forum's Education Programme and secondary schools in the UK. It was developed from a previous publication, Nuclear Bulletin. There is a need for the nuclear industry to build trust with teachers and students in the UK, where for a long time, everything that the industry has said, written or printed has been disregarded by school teachers as propaganda. Over the last few years the industry has put in a great deal of effort to position itself as a provider of educationally sound and socially acceptable information. 'Activate' was an evolution of this idea and there was a hole in the market for a lively, activity and article based magazine that could be used in the classroom. The target audience is principally teachers of science, mathematics and geography, but also includes teachers of art,, English and history with students of between 11 and 18. The results were very positive in that teachers appreciated the colourful and lively nature of activate and they felt that it provided information and opinions in an un biased and non-propagandist way. Their comments about layout, number of activities style of presentation were taken into account and during the summer of 1994 activate was remodelled ready for re launch in September. The feedback so far is good with more teachers signing up every week to receive their own free copy

  19. BUILDING 341 Seismic Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Halle, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-06-15

    The Seismic Evaluation of Building 341 located at Lawrence Livermore National Laboratory in Livermore, California has been completed. The subject building consists of a main building, Increment 1, and two smaller additions; Increments 2 and 3.

  20. Redesign: Upgrading the building stock to meet (new) user demands

    OpenAIRE

    Remoy, H.T.; Van der Voordt, D.J.M.

    2011-01-01

    Financial and real estate crises and “new ways of working” reduce the need for office space. As a consequence, office markets become replacement markets without a quantitative need for new office buildings: new buildings drive out bad buildings. In the Netherlands, currently 14% of the office space is vacant, of which 60% is redundant or obsolete. Office users, guided by the government, consider sustainable office space important for their image and status. Besides they want to be accommodate...

  1. Idle School Buildings in Rural Areas: Will they Be Useful ?

    OpenAIRE

    Cheng, Qiang-ying; Shu, Wen

    2012-01-01

    Taking the case of Enshi City, we survey the supply of public services in rural areas from education, health, culture and social security, reveal the relationship between the use of idle school buildings in rural areas and the improvement of public services in rural areas. On the basis of expounding the status quo of idle school buildings and public services in rural areas of Enshi City, the following recommendations are put forward: using the idle school buildings to develop rural public edu...

  2. 医院临床科室科研秘书队伍现状及改进建议%Status and suggestions on hospital clinical departments research secretary team building

    Institute of Scientific and Technical Information of China (English)

    陈卓; 代荫梅; 周保利

    2011-01-01

    目的:分析临床科室科研秘书队伍情况,提出改进建议,以改善科研秘书队伍现状.方法:从科研秘书的年龄、学历、职称、专业、专兼职、科研情况、存在问题等方面进行分析.结果:队伍年龄不够年轻化,学历、职称较高,兼职情况突出,队伍的稳定性有待提高,业务能力参差不齐.结论:提出科研秘书的选拔条件和基本素质,建立健全科研秘书培训交流制度,建立激励制度以保持科研秘书队伍的稳定性和工作的积极性,制定科研秘书岗位职责,落实科研秘书例会制度,促进医院的科研发展和学科建设,为打造学院型医院奠定基础.%Objectives : To analyze the status of research secretary team in clinical department and to put forward suggestions to improve the current situation of the team. Methods : factors such as age, education, positional titles, specialties, job nature of full time and part-time,researches, existing problems and etc were analyzed. Results : The average age of the team should make more youthful, having high education and positional titles , the situation of part-time prohlem comes into focus . the stahility of the team should he more improved , the professional capabilities are different. Conclusion : The author put forward the conditions of selection and basic qualities of scientific research secretary , establish the system of training exchange system, found the encouraging methods to keep the team ' s stability and initiative of working, formulate the responsibilities of the posts, fulfill the scientific research secretary regular meeting system, so the team of clinical department could he optimized and improved, arcelerate the hospital ' s research developments and discipline construction in order to lay the foundation of academy hospital.

  3. Danish building typologies

    DEFF Research Database (Denmark)

    Wittchen, Kim Bjarne; Kragh, Jesper

    The objective of TABULA is to develop a harmonised building typology for European countries. Each national building typology will consist of a set of residential model buildings with characteristic energy-related properties (element areas of the thermal building envelope, U-values, supply system...... efficiencies). The model buildings will each represent a specific construction period of the country in question and a specific building size. Furthermore the number of buildings, flats and the overall floor areas will be given, which are represented by the different building types of the national typologies....

  4. Development of energy-efficient comfortable ventilation systems with air quality guided volume flow control and continuous monitoring of the window opening status. Part 1. Use of the LuQaS triple sensor for air quality guided volume flow control of mechanical ventilation systems in domestic buildings. Research project; Entwicklung energieeffizienter Komfortlueftungsanlagen mit luftqualitaetsgefuehrter Volumenstromregelung und kontinuierlicher Erfassung des Fensteroeffnungszustandes. Teilbericht 1. Einsatz des LuQaS-Triple-Sensors zur luftqualitaetsgefuehrten Volumenstromregelung von mechanischen Lueftungsanlagen in Wohngebaeuden. Forschungsprojekt

    Energy Technology Data Exchange (ETDEWEB)

    Grossklos, Marc; Ebel, Witta; Knissel, Jens

    2011-05-15

    The report presents the preparatory work on the research project of the above title. The first chapter presents a status report on air quality monitoring inside rooms and evaluates the projects so far in which the LuQaS air quality sensor was used. The second chapter is a documentation of preliminary measurements using the LuQaS sensor in two passive residential buildings and several individual measurements for sensor calibration. It was found that in apartments with mechanical ventilation, the sensor reflects the user activities; further, the measured values indicate signal changes also in the off-air of the building, so that control via central sensors in the ventilation and off-air systems appears feasible. The third chapter discusses control strategies for air quality control. Apart from a discussion of control unit types, operating regimes, methods to determine rated values, and additional control functions, the effects of threshold value control with different threshold limit values and volume flow changes on the air quality of a model building was simulated. The results prove the expectation that the air quality inside a building will be influenced positively by air quality control. Theoretical investigations of the DrD method will be presented in another part-report of the project.

  5. 初中生目睹特大火灾后的心理健康状况%Mental health status of junior middle school students after witnessing big building fire

    Institute of Scientific and Technical Information of China (English)

    尤美娜; 程文红

    2012-01-01

    Objective: To explore the post-traumatic stress disorder (PTSD), anxiety and depression symptoms of junior high school students after witnessing big building fire. Methods: In the middle school which was 200 meters away from a big building fire, all 387 students from grade 6, 7 and 8 were sampled as the study group. Another middle school which was matched with the study school in the school nature and level was selected and the total 480 students from grade 6,7 and 8 were sampled as the control group. All of the participants were assessed with the Essen Trauma Inventory for Kids and Juvenile (ETI-KJ), Screen for Child Anxiety Related Emotional Disorders (SCARED), and Depression Self-rating Scale for Children (DSRSC). Results: The rates of PTSD (total scores of intrusion, avoidance and hyperarousal of ETI-KJ≥27) and suspected PTSD (total score of intrusion, avoidance and hyperarousal of ETI-KJ was 16 - 26) in the study group were higher than that in the control group (5.9% vs. 1.4%, 17. 7% vs. 8.3%, ft 0.05]. Logistic regression analysis indicated that the students who were female(OR = 1. 90), having previous trauma experience (OR = 5.67) and being students of the study school (OR = 1.61) were more likely to get PTSD. Conclusion: It suggests that post-traumatic stress disorder, generalized anxiety and somatic/panic symptoms may occur in junior high school students after witnessing the big fire disaster, which should be noticed when providing psychological support and crisis intervention after disaster.%目的:探讨目睹火灾对初中学生创伤后应激障碍( PTSD)、焦虑及抑郁症状的影响.方法:采用方便抽样方法抽取距某特大火灾现场200米某中学六年级及初一、初二3个年级全体387名学生为研究组,抽取另一区与研究学校性质、等级相匹配的某中学六年级及初一、初二3个年级全体480名学生为对照组,对全体被试施测埃森儿童青少年创伤问卷(ETI-KJ)中文版、儿童焦虑性

  6. Sustainable Buildings in Interaction

    DEFF Research Database (Denmark)

    Elle, Morten

    developments are going to consist of passive houses. The first sustainable buildings were built by their users, and the user – building interaction still play a decisive role for the performance of the present sustainable buildings. The users have to understand how the building functions. Urban design is...... essential for the possibilities of a sustainable building design: orientation and access to infrastructure are important factor. And the building design is decisive in making the city truly compact: dense in activities. In future, the interaction between the technical infrastructure, the buildings and their......The first attempts to build sustainable buildings in Denmark were typically located on the countryside. The basic idea was to create buildings that were independent of the technical infrastructure. District heating has, however, been the dominating solution to heating in buildings in Denmark, and...

  7. RPC PET: Status and perspectives

    Science.gov (United States)

    Couceiro, M.; Blanco, A.; Ferreira, Nuno C.; Ferreira Marques, R.; Fonte, P.; Lopes, L.

    2007-10-01

    The status of the resistive plate chamber (RPC)-PET technology for small animals is briefly reviewed and its sensitivity performance for human PET studied through Monte-Carlo simulations. The cost-effectiveness of these detectors and their very good timing characteristics open the possibility to build affordable Time of Flight (TOF)-PET systems with very large fields of view. Simulations suggest that the sensitivity of such systems for human whole-body screening, under reasonable assumptions, may exceed the present crystal-based PET technology by a factor up to 20.

  8. Building brighter PV business

    International Nuclear Information System (INIS)

    The current status and future prospects of the UK market for solar photovoltaic (PV) electricity are briefly discussed. Through the Department of Trade and Industry (DTI), the UK Government has supported research and development (R and D) into PV for a number of years. This programme has now been extended to demonstrating PV systems on houses. Phase 2 - the domestic field trial programme - aims to monitor the performance of individual systems and the impact on a cluster of systems on the electricity network. New funding had allowed a trebling of the size of this programme, which involves both private developers and housing associations. The DTI is also working to promote PV on commercial buildings, eg the installation of BP Solar PV systems at BP petrol stations. The PV industry in the UK is technically strong and is working to overcome the barriers in the UK to greater uptake of the technology (including cost, conservatism, legal requirements and metering practices). Improvements are expected in a number of recent initiatives in the electricity industry to boost PV use and the PV industry is lobbying for PV to be included in the Enhanced Capital Allowances (ECA) scheme

  9. Global Building Physics

    DEFF Research Database (Denmark)

    Rode, Carsten

    2012-01-01

    aspects of the building as defined in building engineering. We live in an international society and building solutions are developed across country borders. Building physics is a global theme. The International Association of Building Physics has global appeal. The keynote lecture and this brief paper......High ambitions are set for the building physics performance of buildings today. No single technology can achieve fulfilment of these ambitions alone. Integrated, multi-facetted solutions and optimization are necessary. A holistic, or “global”, technological perspective is needed, which includes all...

  10. Global building physics

    DEFF Research Database (Denmark)

    Rode, Carsten

    2013-01-01

    aspects of the building as defined in building engineering. We live in an international society and building solutions are developed across country borders. Building physics is a global theme. The International Association of Building Physics has global appeal. This brief article reports the keynote......High ambitions are set for the building physics performance of buildings today. No single technology can achieve fulfilment of these ambitions alone. Integrated, multi-facetted solutions and optimization are necessary. A holistic, or ‘global’, technological perspective is needed, which includes all...

  11. Retrofitting Listed Buildings

    DEFF Research Database (Denmark)

    Rasmussen, Torben Valdbjørn

    2011-01-01

    The paper presents a case study where the energy demand for a listed building constructed in 1900 is reduced. Many older buildings are listed and have restrictions that include the entire building or that include only its exterior. For the building presented, only its exterior facade is listed. The...... the local urban environment and therefore listed. The reduced energy demand, related to individual measures, is estimated and building physics requirements are addressed together with the economic options for evaluating the profitability....

  12. Research on buildings impacting on aerosol diffusing in urban area using remote sensing

    Institute of Scientific and Technical Information of China (English)

    YANG Sheng-tian; YANG Zhi-feng; MAO Xian-qiang; ZHU Qi-jiang

    2004-01-01

    Employing remote sensing method to interpret the building volumetric ratio and aerosol status in Guangzhou, China. The relation between them and identified characteristics of their spatial distribution was analyzed. Results showed that building density and aerosol status are strongly correlated. It is indicated that the resistance of building to aerosol diffusing is one of factors influencing air pollution in urban area. On the basis of calculated results, building voluminous ratio of 5.6 is taken as the threshold impacting on aerosol diffusing, so the building voluminous ratio of Guangzhou should be limited to less than 5.6 in order to alleviate air pollution.

  13. Importance of Building Code

    Directory of Open Access Journals (Sweden)

    Reshmi Banerjee

    2015-06-01

    Full Text Available A building code, or building control, is a set of rules that specify the minimum standards for constructed objects such as buildings and non building structures. The main purpose of building codes are to protect public health, safety and general welfare as they relate to the construction and occupancy of buildings and structures. The building code becomes law of a particular jurisdiction when formally enacted by the appropriate governmental or private authority. Building codes are generally intended to be applied by architects, engineers, constructors and regulators but are also used for various purposes by safety inspectors, environmental scientists, real estate developers, subcontractors, manufacturers of building products and materials, insurance companies, facility managers, tenants and others.

  14. Sustainable Buildings in Interaction

    DEFF Research Database (Denmark)

    Elle, Morten

    The first attempts to build sustainable buildings in Denmark were typically located on the countryside. The basic idea was to create buildings that were independent of the technical infrastructure. District heating has, however, been the dominating solution to heating in buildings in Denmark, and...... the focus on sustainable building have gradually turned from special houses on the countryside to normally looking houses in the urban fabric, integrated in the technical infrastructure. Some new built urban areas in Denmark will, however, not have to be supplied with district heating – these...... developments are going to consist of passive houses. The first sustainable buildings were built by their users, and the user – building interaction still play a decisive role for the performance of the present sustainable buildings. The users have to understand how the building functions. Urban design is...

  15. Analysis of Some Building Damage Phenomena in the Wenchuan Earthquake

    Institute of Scientific and Technical Information of China (English)

    Li Min; Li Xiaojun

    2012-01-01

    The Ms 8. 0 Wenchuan earthquake caused a great deal of damage and collapse to engineering structures. Survey of disaster and engineering damage was made in detail by the authors and other researchers in the extreme earthquake disaster area. The paper makes an overview of the earthquake disaster status and damage phenomena which include brick-concrete buildings, frame structures, brick-wood structures, and timber frame residential buildings. Furthermore, the causes of the disaster and building damage phenomena are briefly discussed. In addition, some typical damage phenomena are specialized. According to the phenomena mentioned above, some feasible seismic measures are suggested for the development of buildings in future.

  16. The impact of clerestory lights on energy efficiency of buildings

    Directory of Open Access Journals (Sweden)

    Đenadić Dalibor M.

    2015-01-01

    Full Text Available The buildings are among major energy consumers, whose energy efficiency is rather low. Clerestory windows are responsible for a large portion of energy losses from the buildings. The energy efficiency of buildings can greatly be improved by upgrading clerestory and other windows. This paper focuses on the theoretical and experimental investigations on how this can be performed in an old school building in the town of Bor in eastern part of Serbia. For that purpose a modern measuring technique has been applied to identify the existing status, and to compare theoretical and actual conditions.

  17. Applied building physics

    CERN Document Server

    Hens, Hugo S L C

    2012-01-01

    The energy crises of the 1970s, persisting moisture problems, complaints about sick buildings, thermal, visual and olfactory discomfort, and the move towards more sustainability in building construction have pushed Building Physics to the forefront of building innovation. The societal pressure to diminish energy consumption in buildings without impairing usability acted as a trigger to activate the whole notion of performance based design and construction. As with all engineering sciences, Building Physics is oriented towards application, which is why, after a first book on fundamentals this s

  18. Sustainable Building Operation

    DEFF Research Database (Denmark)

    Jensen, Jesper Ole

    2009-01-01

    practical experiences from Danish housing estates indicates that there are large potentials for energy savings by focusing on the operation of the buildings. We suggest that in order to achieve sustainability in the existing housing, renovation and operations should be seen as integrated parts and that...... sustainable building operation can pave the way for sustainable building renovation. This paper discusses the use of sustainability building operation in Danish housing estates: Which tools, methods and technologies is being used, where are the barriers and where are the potentials? We define sustainable...... sustainable building operation and a survey amongst building administrators from the private and the social housing sector. Our results show that there are many good examples on sustainable building operation in Danish housing estates, where local building managers, residents etc. have gained impressive...

  19. Building the Korogwe Laboratory

    DEFF Research Database (Denmark)

    Knudsen, Jakob; von Seidlein, Lorenz; Richard, Jean Pierre

    2011-01-01

    An illustrated description of the building of a biomedical research laboratory in Korogwe, Tanzania.......An illustrated description of the building of a biomedical research laboratory in Korogwe, Tanzania....

  20. Requirements for existing buildings

    DEFF Research Database (Denmark)

    Thomsen, Kirsten Engelund; Wittchen, Kim Bjarne

    2012-01-01

    This report collects energy performance requirements for existing buildings in European member states by June 2012.......This report collects energy performance requirements for existing buildings in European member states by June 2012....

  1. Better Buildings Challenge Overview

    Energy Technology Data Exchange (ETDEWEB)

    None

    2011-06-01

    The Better Buildings Challenge is a national leadership initiative calling on corporate chief executive officers, university presidents, and state and local leaders to make a significant commitment to building energy efficiency.

  2. Environmental indicators for buildings

    DEFF Research Database (Denmark)

    Dammann, Sven

    Environmental Indicators for Buildings are studied using two different perspectives: with a technological, environmental scientific departing point and with a social scientific departing point. Different relevant groups in the building sector are identified and analysed, using the Social...

  3. Robotic buildings(s)

    NARCIS (Netherlands)

    Bier, H.H.

    2014-01-01

    Technological and conceptual advances in fields such as artificial intelligence, robotics, and material science have enabled robotic building to be in the last decade prototypically implemented. In this context, robotic building implies both physically built robotic environments and robotically supp

  4. Integrated Building Health Management

    Data.gov (United States)

    National Aeronautics and Space Administration — Abstract: Building health management is an important part in running an efficient and cost-effective building. Many problems in a building’s system can go...

  5. Building Design & Construction - Sustainability

    Energy Technology Data Exchange (ETDEWEB)

    None

    2003-11-01

    Offers a brief history of green building; presents the results of a specially commissioned survey; and analyzes the chief trends, issues, and published research, based on interviews with dozens of experts and participants in green building.

  6. Comfort control in buildings

    CERN Document Server

    Castilla, Maria del Mar; Rodriguez, Francisco de Asis

    2014-01-01

    This book describes both concepts and development of advanced comfort control systems in buildings, with significant energy saving, and attention to thermal, visual and indoor air quality. The concepts are proven through real tests in a bioclimatic building.

  7. Energy performance in buildings

    International Nuclear Information System (INIS)

    The adoption of the building sector regulations strongly oriented to the energy sustainability becomes more effective, also on the economic plan, if placed by one spread of the energetic certification of the buildings

  8. Allegheny County Building Footprints

    Data.gov (United States)

    Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset contains photogrammetrically compiled roof outlines of buildings. All near orthogonal corners are square. Buildings that are less than 400 square feet...

  9. Buildings interoperability landscape - Draft

    Energy Technology Data Exchange (ETDEWEB)

    Hardin, Dave B. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Stephan, Eric G. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Wang, Weimin [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Corbin, Charles D. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Widergren, Steven E. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States)

    2015-02-01

    Buildings are an integral part of our nation’s energy economy. The advancement in information and communications technology (ICT) has revolutionized energy management in industrial facilities and large commercial buildings. As ICT costs decrease and capabilities increase, buildings automation and energy management features are transforming the small-medium commercial and residential buildings sectors. A vision of a connected world in which equipment and systems within buildings coordinate with each other to efficiently meet their owners’ and occupants’ needs, and where buildings regularly transact business with other buildings and service providers (such as gas and electric service providers) is emerging. However, while the technology to support this collaboration has been demonstrated at various degrees of maturity, the integration frameworks and ecosystems of products that support the ability to easily install, maintain, and evolve building systems and their equipment components are struggling to nurture the fledging business propositions of their proponents.

  10. Biological Sciences Building

    OpenAIRE

    Kumaraswamy, Mohan

    2002-01-01

    One element of the CIVCAL project Web-based resources containing images, tables, texts and associated data on the construction of the Biological Sciences Building. The HKU Kadoorie Biological Sciences Building is an 11-storey reinforced concrete framed building with a structural steel arch roof. The building dimensions are approximately 60 metres x 30 metres. The estimated project cost for the superstructure construction (excluding the bored pile foundations) was about HK$ 400 million....

  11. Marine Building Technology

    OpenAIRE

    Westby, Ola

    2006-01-01

    This textbook is all about building of ships, platforms and other offshore installations. The geometry and functions of systems and structures are explained as an introduction to management and technology at shipyards and building sites. Both loadbearing structures, outfitting and installation of accommodation are included. Project management, production planning, cost calculations, building methods, discipline knowledge (welding, painting, insulation, mechanical, piping etc.), fabrication te...

  12. ICT Enhanced Buildings Potentials

    DEFF Research Database (Denmark)

    Christiansson, Per

    2007-01-01

    with focus on virtual building models support, new services and user environment definitions and development, virtual spaces and augmented reality, intelligent building components, application ontologies, and ICT systems integration to illustrate ICT enhanced buildings potentials and R&D needs.  ...

  13. Facilitating Collaborative Knowledge Building

    Science.gov (United States)

    Hmelo-Silver, Cindy E.; Barrows, Howard S.

    2008-01-01

    This article describes a detailed analysis of knowledge building in a problem-based learning group. Knowledge building involves increasing the collective knowledge of a group through social discourse. For knowledge building to occur in the classroom, the teacher needs to create opportunities for constructive discourse in order to support student…

  14. BNL status and plans

    International Nuclear Information System (INIS)

    The present status and future plans for the Alternating Gradient Synchrotron are presented. The operating modes, accelerator improvement program, Booster synchrotron status, Stretcher ring proposal, and higher intensity options are described

  15. Status of EPR™ projects

    International Nuclear Information System (INIS)

    EPR licensing status, construction status and AREVA reactor portfolio are presented. Details are given for the construction of the Olkiluoto 3, Flamanville 3 Project (France) and Taishan 1 and 2 (China)

  16. USCIS My Case Status

    Data.gov (United States)

    Department of Homeland Security — USCIS provide a way for the public who applied for U.S. citizenship to check the status of their application online. To view the status of a case, the application...

  17. Status of KM3NeT

    Directory of Open Access Journals (Sweden)

    Riccobene G.

    2016-01-01

    Full Text Available The recent observation of cosmic neutrinos by IceCube has pushed the quest towards the identification of cosmic sources of high-energy particles. The KM3NeT Collaboration is now ready to launch the massive construction of detection units to be installed in deep sea to build a km-cubic size neutrino telescope. The main elements of the detector, the status of the project and the expected perfomances are briefly reported.

  18. Status of KM3NeT

    Science.gov (United States)

    Riccobene, G.

    2016-07-01

    The recent observation of cosmic neutrinos by IceCube has pushed the quest towards the identification of cosmic sources of high-energy particles. The KM3NeT Collaboration is now ready to launch the massive construction of detection units to be installed in deep sea to build a km-cubic size neutrino telescope. The main elements of the detector, the status of the project and the expected perfomances are briefly reported.

  19. Building Order in the Building Company Organization

    OpenAIRE

    Krivdová, Magdaléna

    2013-01-01

    The aim of the thesis is to describe an organization of a building order, and to show its key phases. The individual phases of how a order is completed in a company are shown on practical examples. The first two chapters deal with the current situation of today's construction industry; consequently, the reasons for introducing the principles of project management into the construction business practice are mentioned. The third chapter is devoted to the description of a building order. It...

  20. Idle School Buildings in Rural Areas: Will they Be Useful?

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Taking the case of Enshi City,we survey the supply of public services in rural areas from education,health,culture and social security; reveal the relationship between the use of idle school buildings in rural areas and the improvement of public services in rural areas. On the basis of expounding the status quo of idle school buildings and public services in rural areas of Enshi City,the following recommendations are put forward: using the idle school buildings to develop rural public education; using the idle school buildings to develop rural public health and medical services; using the idle school buildings to develop public cultural undertakings in rural areas; using the idle school buildings to develop social security undertakings in rural areas.

  1. Integrated building design

    Science.gov (United States)

    Sanguinetti, Jennifer

    2005-04-01

    For many years, building design has been a very linear process with owners speaking to architects who then design building shells that they pass along to sub-consultants who must fit their systems into the allotted spaces. While this process has some advantages, it provides little opportunity to optimize systems based on such factors as energy use or occupant comfort. This presentation will focus on the evolution and implications of integrated building design, a method that has provided greater opportunities for interaction between design disciplines and with building users early on in the design process. Integration has resulted in buildings that are more sustainable than typical buildings and that can respond better to the needs of the owner and users. Examples of the application of the process and the resulting buildings will be presented from the view of a design engineer with experience of both processes. Specifically, the potential contribution of an acoustical consultant in the integrated process will be explored.

  2. Commercial Buildings Characteristics, 1992

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-29

    Commercial Buildings Characteristics 1992 presents statistics about the number, type, and size of commercial buildings in the United States as well as their energy-related characteristics. These data are collected in the Commercial Buildings Energy Consumption Survey (CBECS), a national survey of buildings in the commercial sector. The 1992 CBECS is the fifth in a series conducted since 1979 by the Energy Information Administration. Approximately 6,600 commercial buildings were surveyed, representing the characteristics and energy consumption of 4.8 million commercial buildings and 67.9 billion square feet of commercial floorspace nationwide. Overall, the amount of commercial floorspace in the United States increased an average of 2.4 percent annually between 1989 and 1992, while the number of commercial buildings increased an average of 2.0 percent annually.

  3. Heuristic status polling

    Science.gov (United States)

    Archer, Charles J.; Blocksome, Michael A.; Heidelberger, Philip; Kumar, Sameer; Parker, Jeffrey J.; Ratterman, Joseph D.

    2011-06-07

    Methods, compute nodes, and computer program products are provided for heuristic status polling of a component in a computing system. Embodiments include receiving, by a polling module from a requesting application, a status request requesting status of a component; determining, by the polling module, whether an activity history for the component satisfies heuristic polling criteria; polling, by the polling module, the component for status if the activity history for the component satisfies the heuristic polling criteria; and not polling, by the polling module, the component for status if the activity history for the component does not satisfy the heuristic criteria.

  4. Capacity Building: Building Human Capital Through Enhanced Science Education

    International Nuclear Information System (INIS)

    The problem Africa is facing is under-development that manifests itself in terms of poverty, diseases, ignorance and many other forms.s It is regrettable to recognize and note that due to severe but an apparent lack of funds and other resources, many african countries have remained impoverished over the years.The weak fiscal status and the dim prospects for drastic economic improvement coupled with mismanagement, corrupt and , at times, despotic regimes in the continent also militate against any significant local support to alleviate the problems of under-development in the near future. From the experience of the industrialized countries, its abundantly clear that for Africa to Develop and survive this century, science and technology must take root in the continent to serve the people and and improve their standards of living by increasing productivity. Its also well understood and recognized that for science and technology to benefit the continent, human resources development , i.e., capacity building in general is paramount and basic. There are a number of Prerequisites for capacity building and these involves issues and questions which must be addressed

  5. Building for animal production

    International Nuclear Information System (INIS)

    In order to limit the radiation dose to persons working with animal husbandry in severe fallout situations, it was considered necessary to make an inventory of the Swedish livestock buildings as to number, location, use and size. These data as well as data on geometry of buildings, building material and thickness of the material in walls and roofs are given in the present work. On the basis of the mentioned data, calculations were made of the shielding factors of different types of livestock buildings. The collected data can also be used in preparedness planning in relation to housing facilities for livestock and location and size of animal production in situations of crises or war. The calculations show shielding factors for different types of livestock buildings of normal ground area within the range of 0.18-0.71. The higher value indicates a fairly poor shielding effect. The inventory and the calculations show that in those regions in Sweden where the main part of the livestock is managed, the types of buildings are, however, characterized by radiation shielding factors of 0.3-0.4. Calculation were also made of the radiation level inside the buildings following decontamination of roofs or of surrounding ground. Ground decontamination only, i.e., removal of the upper contaminated surface layer, will reduce the radiation level inside the building. For most buildings the radius of the surrounding area to be decontaminated has to be 15-30 times larger than the width of the building in order to achieve a 50 percentage reduction of the radiation level inside the building. For buildings of medium or large size and with thick walls the radiation contribution from the roof is greater than the radiation from the ground, and regardless of the size of the ground areas decontaminated the radiation level inside these buildings will only be reduced by 20-30%. 15 refs, 11 figs, 14 tabs

  6. Status of irradiation technology development in JMTR

    International Nuclear Information System (INIS)

    Irradiation Engineering Section of the Neutron Irradiation and Testing Reactor Center was organized to development the new irradiation technology for the application at JMTR re-operation. The new irradiation engineering building was remodeled from the old RI development building, and was started to use from the end of September, 2008. Advanced in-situ instrumentation technology (high temperature multi-paired thermocouple, ceramic sensor, application of optical measurement), 99Mo production technology by new Mo solution irradiation method, recycling technology on used beryllium reflector, and so on are planned as the development of new irradiation technologies. The development will be also important for the education and training programs through the development of young generation in not only Japan but also Asian counties. In this report, as the status of the development the new irradiation technology, new irradiation engineering building, high temperature multi-paired thermocouple, experiences of optical measurement, recycling technology on used beryllium reflector are introduced. (author)

  7. [Epidemiology of "sick buildings"].

    Science.gov (United States)

    Sterling, T D; Collett, C; Rumel, D

    1991-02-01

    The indoor environment of modern buildings, especially those designed for commercial and administrative purposes, constitutes a unique ecological niche with its own biochemical environment, fauna and flora. Sophisticated construction methods and the new materials and machinery required to maintain the indoor environment of these enclosed structures produce a large number of chemical by-products and permit the growth of many different microorganisms. Because modern office buildings are sealed, the regulation of humidification and temperature of ducted air presents a dilemma, since difference species of microorganisms flourish at different combinations of humidity and temperature. If the indoor environment of modern office buildings is not properly maintained, the environment may become harmful to its occupants' health. Such buildings are classified as "Sick Buildings". A review of the epidemiology of building illness is presented. The etiology of occupant illnesses, sources of toxic substances, and possible methods of maintaining a safe indoor environment are described. PMID:1784964

  8. Radon in buildings

    International Nuclear Information System (INIS)

    This guide is intended to inform designers, contractors, householders and other building owners about radon in buildings and to provide guidance where it has been decided to take action to reduce radon levels. It gives some pointers to good practice insofar as it relates to non complex buildings of normal design and construction. Reference is made to the usual ways of reducing l;levels of radon and guidance is given on sources of further information. I

  9. Development of Ecological Buildings

    Directory of Open Access Journals (Sweden)

    Andrius Keizikas

    2011-04-01

    Full Text Available The article presents research on ecological buildings and their influence on the constructional sphere. The aim of the paper is to reveal the essence of ecological architecture showing substantial progress and its potential to stimulate architectural and technological growth. The article also describes relations between the ideas of ecological buildings and the ‘passive house’ concepts and aspects of development as well as describes the possibilities of improving building sustainability and energy efficiency. Article in Lithuanian

  10. Radon in buildings

    International Nuclear Information System (INIS)

    This guide is intended to inform designers, householders and other building owners about the radon problem and to help in deciding if there is need to take any action to reduce radon levels in their homes or other buildings.It explains what radon is, how it enters buildings and what effect it may have on health. Reference is made to some of the usual ways of reducing the level of radon and guidance is given on some sources of assistance

  11. Building valve amplifiers

    CERN Document Server

    Jones, Morgan

    2013-01-01

    Building Valve Amplifiers is a unique hands-on guide for anyone working with tube audio equipment--as an electronics hobbyist, audiophile or audio engineer. This 2nd Edition builds on the success of the first with technology and technique revisions throughout and, significantly, a major new self-build project, worked through step-by-step, which puts into practice the principles and techniques introduced throughout the book. Particular attention has been paid to answering questions commonly asked by newcomers to the world of the valve, whether audio enthusiasts tackling their first build or

  12. Sick building syndrome

    Directory of Open Access Journals (Sweden)

    Tjandra Y. Aditama

    2002-06-01

    Full Text Available Sick building syndrome describes a number of mostly unspesific complaints of some occupants of the building. The exact pathophysiological mechanism remains elusive. It is a multi factorial event which may include physical, chemical, biological as well as psycological factors. In many cases it is due to insufficient maintenance of the HVAC (heating, ventilation, air conditioning system in the building. Sign and symptoms can be uncomfortable and even disabling, which may include mucus membrane irritation, neurotoxic symptoms, asthma like symptoms, skin complaints, gastrointestinal symptoms and other related symptoms. There are various investigation methods to diagnose sick building syndrome, and on site assessment of the building is extremely useful. Prevention through a proactive air quality monitoring program is far more desirable than dealing with an actual sick building. Indoor air and the sick building symdrome serves as a paradigm of modern occupational and environmental medicine. (Med J Indones 2002; 11:124-31Keywords: indoor air pollution, sick building syndrome, building related illness

  13. Nuclear reactor building

    International Nuclear Information System (INIS)

    Purpose: To prevent seismic vibrations of external buildings from transmitting to the side walls of a reactor container in a tank type FBR reactor building. Constitution: The reactor building is structured such that the base mat for a reactor container chamber and a reactor container is separated from the base mat for the walls of building, and gas-tight material such as silicon rubber is filled in the gap therebetween. With such a constitution, even if the crane-supporting wall vibrates violently upon occurrence of earthqualkes, the seismic vibrations do not transmit toward the reactor container chamber. (Horiuchi, T.)

  14. Grassmannians of classical buildings

    CERN Document Server

    Pankov, Mark

    2010-01-01

    Buildings are combinatorial constructions successfully exploited to study groups of various types. The vertex set of a building can be naturally decomposed into subsets called Grassmannians. The book contains both classical and more recent results on Grassmannians of buildings of classical types. It gives a modern interpretation of some classical results from the geometry of linear groups. The presented methods are applied to some geometric constructions non-related to buildings - Grassmannians of infinite-dimensional vector spaces and the sets of conjugate linear involutions. The book is self

  15. Healthy Buildings '88

    International Nuclear Information System (INIS)

    The Healthy Buildings '88 Conference focuses on the technical solutions and functional requirements contributing to Healthy Buildings for people to live and work in. The main object of the Conference is to give architects, consultants, real-estate owners and manufacturers of building materials recommendations on choice of materials and choice of systems and on how to combine materials and systems. The program includes overview lectures, plenary symposia with invited speakers, workshops, poster presentations and an exhibition of scientific, educational and technical material. One part of the conference is devoted to the problem of radon in residential buildings

  16. Research update, existing buildings research, 1989--1991

    Energy Technology Data Exchange (ETDEWEB)

    MacDonald, J.M.; Ternes, M.P.; Mixon, W.R.; Sharp, T.R.; Kolb, J.O.; Wilkes, K.E. [Oak Ridge National Lab., TN (United States); Diamond, R.C. [Lawrence Berkeley Lab., CA (United States); Judkoff, R. [National Renewable Energy Lab., Golden, CO (United States); Mazzucchi, R.P. [Pacific Northwest Lab., Richland, WA (United States)

    1993-02-01

    This Research Update presents the status of the Existing Buildings Research program of the Office of Building Technologies of the US Department of Energy for the period 1989-199 1. This program covers research on energy efficiency improvements for the residential and commercial buildings in this country. ne Existing Buildings Research program has contributed to significant improvements in energy efficiency of existing buildings by development of improvements to retrofit technologies, by coordinating and conducting research studies on the use of energy efficiency technologies (to reduce barriers and increase use), and by continually evaluating changes in technologies that could improve and maintain buildings energy efficiency. If the energy efficiency of the buildings sector in this country is to be dramatically improved over the next 30 years, we must improve the use of energy efficiency technologies. Improved delivery of measures, improved understanding of how buildings actually perform in the field, and methods for improving operations and maintenance of buildings and energy equipment are all examples of ways to improve the deployment (transfer) of technologies. Much has been learned about technology deployment in buildings in the first five years of the program, and our future plans will be directed at continuing the improvements and making a real contribution to the energy efficiency future of the United States.

  17. A View on Future Building System Modeling and Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Wetter, Michael

    2011-04-01

    This chapter presents what a future environment for building system modeling and simulation may look like. As buildings continue to require increased performance and better comfort, their energy and control systems are becoming more integrated and complex. We therefore focus in this chapter on the modeling, simulation and analysis of building energy and control systems. Such systems can be classified as heterogeneous systems because they involve multiple domains, such as thermodynamics, fluid dynamics, heat and mass transfer, electrical systems, control systems and communication systems. Also, they typically involve multiple temporal and spatial scales, and their evolution can be described by coupled differential equations, discrete equations and events. Modeling and simulating such systems requires a higher level of abstraction and modularisation to manage the increased complexity compared to what is used in today's building simulation programs. Therefore, the trend towards more integrated building systems is likely to be a driving force for changing the status quo of today's building simulation programs. Thischapter discusses evolving modeling requirements and outlines a path toward a future environment for modeling and simulation of heterogeneous building systems.A range of topics that would require many additional pages of discussion has been omitted. Examples include computational fluid dynamics for air and particle flow in and around buildings, people movement, daylight simulation, uncertainty propagation and optimisation methods for building design and controls. For different discussions and perspectives on the future of building modeling and simulation, we refer to Sahlin (2000), Augenbroe (2001) and Malkawi and Augenbroe (2004).

  18. Building America Expert Meeting Report. Transitioning Traditional HVAC Contractors to Whole House Performance Contractors

    Energy Technology Data Exchange (ETDEWEB)

    Burdick, Arlan [IBACOS Inc., Pittsburgh, PA (United States)

    2011-10-01

    This expert meeting was hosted by the IBACOS Building America research team to determine how HVAC companies can transition from a traditional contractor status to a service provider for whole house energy upgrade contracting.

  19. WASTE HANDLING BUILDING VENTILATION SYSTEM DESCRIPTION DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    P.A. Kumar

    2000-06-21

    The Waste Handling Building Ventilation System provides heating, ventilation, and air conditioning (HVAC) for the contaminated, potentially contaminated, and uncontaminated areas of the Monitored Geologic Repository's (MGR) Waste Handling Building (WHB). In the uncontaminated areas, the non-confinement area ventilation system maintains the proper environmental conditions for equipment operation and personnel comfort. In the contaminated and potentially contaminated areas, in addition to maintaining the proper environmental conditions for equipment operation and personnel comfort, the contamination confinement area ventilation system directs potentially contaminated air away from personnel in the WHB and confines the contamination within high-efficiency particulate air (HEPA) filtration units. The contamination confinement areas ventilation system creates airflow paths and pressure zones to minimize the potential for spreading contamination within the building. The contamination confinement ventilation system also protects the environment and the public by limiting airborne releases of radioactive or other hazardous contaminants from the WHB. The Waste Handling Building Ventilation System is designed to perform its safety functions under accident conditions and other Design Basis Events (DBEs) (such as earthquakes, tornadoes, fires, and loss of the primary electric power). Additional system design features (such as compartmentalization with independent subsystems) limit the potential for cross-contamination within the WHB. The system provides status of important system parameters and equipment operation, and provides audible and/or visual indication of off-normal conditions and equipment failures. The Waste Handling Building Ventilation System confines the radioactive and hazardous material within the building such that the release rates comply with regulatory limits. The system design, operations, and maintenance activities incorporate ALARA (as low as is

  20. Service Level Status

    CERN Multimedia

    Lopienski, S

    2007-01-01

    Nowadays, IT departments provide, and people use, computing services of an increasingly heterogeneous nature. There is thus a growing need for a status display that groups these different services and reports status and availability in a uniform way. The Service Level Status (SLS) system addresses these needs by providing a web-based display that dynamically shows availability, basic information and statistics about various IT services, as well as the dependencies between them.

  1. Nonkonvulsif Status Epileptikus

    OpenAIRE

    Ayhan AKÖZ; ÖZEL, Lütfi; Bayramoğlu, Atıf; Saritemur, Murat; Recep DEMİR; Zeynep GÖKCAN ÇAKIR

    2013-01-01

    Status epilepticus (SE) can be divided into two subgroups, convulsive status epilepticus (CSE) and nonconvulsive status epilepticus (NCSE). NCSE is clinically characterized by recurrence or persistence of absence or complex partial seizures which unconsciousness persists. Seizures are lasted more than 30 minutes, and accompanied by mental and behavioral changes. Although the main feature is the change of level of consciousness, affective, memory, cognitive, speech, motor systems, behavioral a...

  2. SIS - Status Determination

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Status Determination dataset within the Species Information System (SIS) contains information related to overfishing, overfished, and approaching overfished...

  3. The Building of Environmental Geographic Information System for Supporting Environmental Policymaking in Korea

    OpenAIRE

    Bae, Minki; Cho, Deokho; Um, HongSuk; Shin, Dongho

    2004-01-01

    The goal of this study is to build a geographic information system for environmental policymaking. To achieve this goal, this study first surveys the local environment status. Based upon the collected environmental data, it forecasts the future environmental status of each city in Gyeongbuk province and generates a geo-referencing code. Finally, by using these data, it builds up a future environmental geographic information system for supporting environmental policymaking. This study consists...

  4. School Building Defect Pattern

    Directory of Open Access Journals (Sweden)

    Mahli M.

    2014-01-01

    Full Text Available In providing a conducive learning environment for the student, the school building must be in good condition. This paper is evaluating the existing condition of primary school building in Sarawak, Malaysia. It focuses on building defects pattern for school building. The primary data collection is from the school building condition survey with involvement of 24 primary schools. The schools have been selected using simple random sampling and stratified sampling (of school age as the variable of selection. The reporting method is based on Condition Survey Protocol (CSP 1 Matrix. Data analysis covers descriptive and inferential statistics. The analysis carried out found that the overall 4,725 defects have been identified. The building defect pattern is mainly on Ground Level of 3,176 defects, the highest number of defects components found on walls (798. 16.2% defects are cracks from 11 common defects and most of all the highest score of defects based on age of the building were the building in the range of 11 to 20 years.

  5. Integrated Building Design

    DEFF Research Database (Denmark)

    Heiselberg, Per

    In the first half of the 20th century, HVAC systems and artificial lighting were developed to meet indoor comfort needs. Before the introduction of mechanical systems, climate - not building style or appearance - was the major determinant of building form. Comfort was achieved through passive mea...

  6. Building with shapes

    CERN Document Server

    Mooney, Carla

    2014-01-01

    There are shapes everywhere you look. You can put shapes together or build with them. What can you build with three circles? In this title, students will explore and understand that certain attributes define what a shape is called. This title will allow students to identify the main purpose of a text, including what the author wants to answer, explain, or describe.

  7. Dancing building prevents collapse

    NARCIS (Netherlands)

    Visscher, R.

    2007-01-01

    In future, anybody caught inside a building during an earthquake need no longer fear the roof collapsing on them. Thanks to the use of composite materials, all the building will do is dance along, riding the waves of the earthquake. At least, according to Professor Ir. Adriaan Beukers of the Aerospa

  8. Heat loss from Buildings

    DEFF Research Database (Denmark)

    Karlsson, Kenneth; Næraa, Rikke

    1997-01-01

    Determination of heat loss coefficients for buildings in Denmark. The coefficient are determined for 15 building groups and 3 year intervals. They are based on the BBR-registre and assumptions of U-values(W/K*m2)and computed in a simple spreed sheet model.The results are used in the REVEILLE...

  9. Building a Better Robot

    Science.gov (United States)

    Navah, Jan

    2012-01-01

    Kids love to build robots, letting their imaginations run wild with thoughts of what they might look like and what they could be programmed to do. Yet when students use cereal boxes and found objects to make robots, often the projects look too similar and tend to fall apart. This alternative allows students to "build" robots in a different way,…

  10. Building a Data Warehouse.

    Science.gov (United States)

    Levine, Elliott

    2002-01-01

    Describes how to build a data warehouse, using the Schools Interoperability Framework (www.sifinfo.org), that supports data-driven decision making and complies with the Freedom of Information Act. Provides several suggestions for building and maintaining a data warehouse. (PKP)

  11. Building Numbers from Primes

    Science.gov (United States)

    Burkhart, Jerry

    2009-01-01

    Prime numbers are often described as the "building blocks" of natural numbers. This article shows how the author and his students took this idea literally by using prime factorizations to build numbers with blocks. In this activity, students explore many concepts of number theory, including the relationship between greatest common factors and…

  12. Body-building

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    正In recent years, more and more people spare no pains to join in the body-building group. People begin to take part in various fitness clubs or fitness centers in their spare time. This shows body-building has become an indispensable part of many people’s life.

  13. Electromagnetically shielded building

    International Nuclear Information System (INIS)

    This invention relates to a building having an electromagnetic shield structure well-suited for application to an information network system utilizing electromagnetic waves, and more particularly to an electromagnetically shielded building for enhancing the electromagnetic shielding performance of an external wall. 6 figs

  14. Filtrations and Buildings

    OpenAIRE

    Cornut, Christophe

    2014-01-01

    We construct and study a scheme theoretical version of the Tits vectorial building, relate it to filtrations on fiber functors, and use them to clarify various constructions pertaining to Bruhat-Tits buildings, for which we also provide a Tannakian description.

  15. Technical Management for Buildings

    CERN Document Server

    Vairo, Antonio

    1999-01-01

    This paper is a presentation of an 'instrument' for the optimization of the functionality and conservation of tertiary buildings. This technique has several different names: Building Automation Systems (BAS), Central Control and Monitoring System (CCMS) in English, and Gestion Technique du Bâtiment' (GTB) or Gestion Technique Centralisée (GTC) in French. With this technique it is possible to manage all the functions of a building, it is a modern instrument that introduces the concept of 'automation' in the operation of buildings using computerized procedures, earlier reserved for industrial processes. The system is structured with different automation levels with a distributed intelligence, each level characterized by a communication system (Fieldbus for the lowest and Ethernet for the highest level). In order to apply the BAS to CERN buildings it is necessary to evaluate the advantages, the CERN requirements and the integration with the several existing control and automation systems.

  16. CERN's newest building

    CERN Multimedia

    Anaïs Vernède

    2011-01-01

    With a growing number of users looking for offices, the shortage of space has become acute, particularly for physicists. Building 42, inaugurated on Friday 11 February, offers almost 300 new work-spaces and a particularly pleasant working environment.   Mauro Dell’Ambrogio, the Swiss State Secretary for Education and Research (left), Rolf Heuer , CERN Director-General (centre), and Mark Muller, President of the Government of the Republic and Canton of Geneva and Head of the Department of Construction and Information Technology (right) at the opening of Building 42 on 11 February, 2011.   Construction work for the new Building 42 began in January 2009, thanks to support from the Swiss foundation FIPOI (Fondation des immeubles pour les organisations internationales). After two years of work, the building, an extension of Building 40, is ready to accommodate physicists from around the world who have come to work on the LHC. "We had more than 25 external contractors working...

  17. Facade treatments of historical buildings: Limiting the risks

    NARCIS (Netherlands)

    Van Hees, R.P.J.

    2013-01-01

    The usefulness of treatment of facades of historic buildings and especially those with the status of listed monument is often discussed. Surface treatments of facades comprise a range of treatments, from water repellents to consolidants and anti-­graffiti coatings. Even facade cleaning can be consid

  18. WASTE TREATMENT BUILDING VENTILATION SYSTEM DESCRIPTION DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    P.A. Kumar

    2000-06-22

    The Waste Treatment Building Ventilation System provides heating, ventilation, and air conditioning (HVAC) for the contaminated, potentially contaminated, and uncontaminated areas of the Monitored Geologic Repository's (MGR) Waste Treatment Building (WTB). In the uncontaminated areas, the non-confinement area ventilation system maintains the proper environmental conditions for equipment operation and personnel comfort. In the contaminated and potentially contaminated areas, in addition to maintaining the proper environmental conditions for personnel comfort and equipment operation, the contamination confinement area ventilation system directs potentially contaminated air away from personnel in the WTB and confines the contamination within high-efficiency particulate air (HEPA) filtration units. The contamination confinement area ventilation system creates airflow paths and pressure zones to minimize the potential for spreading contamination with the building. The contamination confinement ventilation system also protects the environment and the public by limiting airborne releases of radioactive or other hazardous contaminants from the WTB. The Waste Treatment Building Ventilation System confines the radioactive and hazardous material within the building such that the release rates comply with regulatory limits, The system design, operations, and maintenance activities incorporate ALARA (as low as is reasonably achievable) principles to maintain personnel radiation doses to all occupational workers below regulatory limits and as low as is reasonably achievable. The system provides status of important system parameters and equipment operation, and provides audible and/or visual indication of off-normal conditions and equipment failures. The Waste Treatment Building Ventilation System interfaces with the Waste Treatment Building System by being located in the WTB, and by maintaining specific pressure, temperature, and humidity environments within the building

  19. Energy management systems in buildings

    Energy Technology Data Exchange (ETDEWEB)

    Lush, D.M.

    1979-07-01

    An investigation is made of the range of possibilities available from three types of systems (automatic control devices, building envelope, and the occupants) in buildings. The following subjects are discussed: general (buildings, design and personnel); new buildings (envelope, designers, energy and load calculations, plant design, general design parameters); existing buildings (conservation measures, general energy management, air conditioned buildings, industrial buildings); man and motivation (general, energy management and documentation, maintenance, motivation); automatic energy management systems (thermostatic controls, optimized plant start up, air conditioned and industrial buildings, building automatic systems). (MCW)

  20. Knowledge formalization of intelligent building

    Science.gov (United States)

    Žáček, Martin

    2016-06-01

    This article aim is understanding the basic knowledge about an intelligent building. The notion of the intelligent building can be called any building equipped with computer and communication technology, which can automatically respond to internal or external stimuli. The result of the intelligent building is an automated and foreseeing of activities that enable to reduce operating costs and increase comfort. The best way to use the intelligent building is for a low-energy building, a passive building, or for building with high savings. The output of this article is the formalization of basic knowledge of the intelligent building by RDF graph.

  1. Building Sustainability Assessment

    Directory of Open Access Journals (Sweden)

    Heli Koukkari

    2010-07-01

    Full Text Available Although social, economic, and cultural indicators are of substantial importance to the concept of sustainable building, this concept is usually related to environmental characteristics. Any building level assessment method is complex and involves contradictory aspects. Moreover, emphasizing qualitative criteria only increases confusion. R&D and standardization are thus concentrated to transparency and usability of the environmental methods. Other directions of research aim at performance-based design and methods to take regional and cultural aspects into account. In this paper, the perspectives of the sustainability assessment of a whole building are presented, based on a state of the art, feasibility study on performance analysis and the development of an extended life-cycle assessment for buildings. Using various tools, and based on the case studies of building sustainability assessment, environmental indicators were often shown to be of lesser importance than the other, soft ones. The first steps in the development of a building sustainability assessment method for Portuguese residential buildings will be presented and discussed in the end.

  2. Building Software with Gradle

    CERN Document Server

    CERN. Geneva; Studer, Etienne

    2014-01-01

    In this presentation, we will give an overview of the key concepts and main features of Gradle, the innovative build system that has become the de-facto standard in the enterprise. We will cover task declaration and task graph execution, incremental builds, multi-project builds, dependency management, applying plugins, extracting reusable build logic, bootstrapping a build, and using the Gradle daemon. By the end of this talk, you will have a good understanding of what makes Gradle so powerful yet easy to use. You will also understand why companies like Pivotal, LinkedIn, Google, and other giants with complex builds count on Gradle. About the speakers Etienne is leading the Tooling Team at Gradleware. He has been working as a developer, architect, project manager, and CTO over the past 15 years. He has spent most of his time building software products from the ground up and successfully shipping them to happy customers. He had ...

  3. Building-integrated photovoltaics

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-01-01

    This is a study of the issues and opportunities for building-integrated PV products, seen primarily from the perspective of the design community. Although some quantitative analysis is included, and limited interviews are used, the essence of the study is qualitative and subjective. It is intended as an aid to policy makers and members of the technical community in planning and setting priorities for further study and product development. It is important to remember that the success of a product in the building market is not only dependent upon its economic value; the diverse group of building owners, managers, regulators, designers, tenants and users must also find it practical, aesthetically appealing and safe. The report is divided into 11 sections. A discussion of technical and planning considerations is followed by illustrative diagrams of different wall and roof assemblies representing a range of possible PV-integration schemes. Following the diagrams, several of these assemblies are then applied to a conceptual test building which is analyzed for PV performance. Finally, a discussion of mechanical/electrical building products incorporating PVs is followed by a brief surveys of cost issues, market potential and code implications. The scope of this report is such that most of the discussion does not go beyond stating the questions. A more detailed analysis will be necessary to establish the true costs and benefits PVs may provide to buildings, taking into account PV power revenue, construction costs, and hidden costs and benefits to building utility and marketability.

  4. Buildings Interoperability Landscape

    Energy Technology Data Exchange (ETDEWEB)

    Hardin, Dave [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stephan, Eric G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wang, Weimin [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Corbin, Charles D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Widergren, Steven E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-12-31

    Through its Building Technologies Office (BTO), the United States Department of Energy’s Office of Energy Efficiency and Renewable Energy (DOE-EERE) is sponsoring an effort to advance interoperability for the integration of intelligent buildings equipment and automation systems, understanding the importance of integration frameworks and product ecosystems to this cause. This is important to BTO’s mission to enhance energy efficiency and save energy for economic and environmental purposes. For connected buildings ecosystems of products and services from various manufacturers to flourish, the ICT aspects of the equipment need to integrate and operate simply and reliably. Within the concepts of interoperability lie the specification, development, and certification of equipment with standards-based interfaces that connect and work. Beyond this, a healthy community of stakeholders that contribute to and use interoperability work products must be developed. On May 1, 2014, the DOE convened a technical meeting to take stock of the current state of interoperability of connected equipment and systems in buildings. Several insights from that meeting helped facilitate a draft description of the landscape of interoperability for connected buildings, which focuses mainly on small and medium commercial buildings. This document revises the February 2015 landscape document to address reviewer comments, incorporate important insights from the Buildings Interoperability Vision technical meeting, and capture thoughts from that meeting about the topics to be addressed in a buildings interoperability vision. In particular, greater attention is paid to the state of information modeling in buildings and the great potential for near-term benefits in this area from progress and community alignment.

  5. Main Street Zero Energy Buildings: The Zero Energy Method in Concept and Practice: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Torcellini, P.; Pless, S.; Lobato, C.; Hootman, T.

    2010-07-01

    Ongoing work at the National Renewable Energy Laboratory indicates that net-zero energy building (NZEB) status is both achievable and repeatable today. This paper presents a definition framework for classifying NZEBs and a real-life example that demonstrates how a large-scale office building can cost-effectively achieve net-zero energy.

  6. Building-Integrated Photovoltaics (BIPV) in the Residential Sector: An Analysis of Installed Rooftop System Prices

    Energy Technology Data Exchange (ETDEWEB)

    James, T.; Goodrich, A.; Woodhouse, M.; Margolis, R.; Ong, S.

    2011-11-01

    For more than 30 years, there have been strong efforts to accelerate the deployment of solar-electric systems by developing photovoltaic (PV) products that are fully integrated with building materials. This report examines the status of building-integrated PV (BIPV), with a focus on the cost drivers of residential rooftop systems, and explores key opportunities and challenges in the marketplace.

  7. Measuring the Scale of a Minoan Building Project. Methodological and Interpretive Issues

    OpenAIRE

    Devolder, Maud; ‘Organisation großer Bauvorhaben in altorientalischen Gesellschaften’, 24.-25.04.2014, Berlin, organised by TOPOI - (B-2) XXL – Monumentalized Knowledge: Extra-Large Projects in Ancient Civilizations

    2014-01-01

    The presentation evaluates the manpower involved in the construction of a sample of 23 Neopalatial buildings (Crete) through an energetic approach by estimating the time (expressed in person-hours) invested in building projects. It addresses the impact of construction on the communities, the status and availability of the builders, and the perception and use of material, structural and symbolic features in Minoan architecture.

  8. A Learning Package in Energy Conservation for Participants in the Home Building Industry. Final Report.

    Science.gov (United States)

    Houston Univ., TX. College of Architecture.

    Presented is the final report for a project designed to develop an experimental learning package for educating participants in the home building industry in energy conservation. The project addresses deficiencies in the present knowledge status of members of the home building industry, effective marketing techniques for energy conserving homes,…

  9. The corporate brand building

    OpenAIRE

    Wisterová, Veronika

    2011-01-01

    The target of this master's thesis is to follow the process of corporate brand building of the company Starkl zahradník, to analyse it and to suggest possible improvements. The thesis is divided into four main sections. The first section deals with the theoretical aspects of the corporate brand building. The second section observes the process of brand building of the brand Starkl zahradník. The third section deals with the survey that was carried out and analyse its results. This survey was ...

  10. Building Social Web Applications

    CERN Document Server

    Bell, Gavin

    2009-01-01

    Building a web application that attracts and retains regular visitors is tricky enough, but creating a social application that encourages visitors to interact with one another requires careful planning. This book provides practical solutions to the tough questions you'll face when building an effective community site -- one that makes visitors feel like they've found a new home on the Web. If your company is ready to take part in the social web, this book will help you get started. Whether you're creating a new site from scratch or reworking an existing site, Building Social Web Applications

  11. INL Green Building Strategy

    Energy Technology Data Exchange (ETDEWEB)

    Jennifer Dalton

    2005-05-01

    Green buildings, also known as sustainable buildings, resource efficient buildings, and high performance buildings, are structures that minimize the impact on the environment by using less energy and water, reducing solid waste and pollutants, and limiting the depletion of natural resources. As Idaho National Laboratory (INL) becomes the nation’s premier nuclear energy research laboratory, the physical infrastructure will be established to help accomplish the mission. This infrastructure, particularly the buildings, should incorporate green design features in order to be environmentally responsible and reflect an image of progressiveness and innovation to the public and prospective employees. With this in mind, the recommendations described in this strategy are intended to form the INL foundation for green building standards. The recommendations in this strategy are broken down into three levels: Baseline Minimum, Leadership in Energy and Environmental Design (LEED)Certification, and Innovative. Baseline Minimum features should be included in all new occupied buildings no matter what the purpose or size. These features do not require significant research, design, or capital costs and yet they can reduce Operation and Maintenance (O&M) costs and produce more environmentally friendly buildings. LEED Certification features are more aggressive than the Baseline Minimums in that they require documentation, studies, and/or additional funding. Combined with the Baseline Minimums, many of the features in this level will need to be implemented to achieve the goal of LEED certification. LEED Silver certification should be the minimum goal for all new buildings (including office buildings, laboratories, cafeterias, and visitor centers) greater than 25,000 square feet or a total cost of $10 million. Innovative features can also contribute to LEED certification, but are less mainstream than those listed in the previous two levels. These features are identified as areas where

  12. Building for energy conservation

    Energy Technology Data Exchange (ETDEWEB)

    O' Callaghan, P.W.

    1978-01-01

    The need to conserve energy, how energy may be saved, and thermal energy conservation in buildings are discussed in the introductory chapter. Heat gains and losses, fluid flow, convective heat transfer, and radiative heat transfer are covered in chapter 2, fundamentals. Thermal comfort, climate, heat losses from buildings, heat gains to buildings, thermal network analysis, energy thrift, secondary effects, waste heat recovery, and altenative energy sources are subjects covered in chapters 3 to 11. The final chapter, prospectus for the future, covers discussions on areas where energy should be saved, total energy, energy management, energy accounting, and practicing energy conservation. (MCW)

  13. Buildings exposed to fire

    International Nuclear Information System (INIS)

    The 24 lectures presented to the colloquium cover the following subject fields: (1) Behaviour of structural components exposed to fire; (2) Behaviour of building materials exposed to fire; (3) Thermal processes; (4) Safety related, theoretical studies. (PW)

  14. Municipal Building Energy Usage

    Data.gov (United States)

    Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This data set contains energy use data from 2009-2014 for 139 municipally operated buildings. Metrics include: Site & Source EUI, annual electricity, natural...

  15. Buildings Sector Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Hostick, Donna J.; Nicholls, Andrew K.; McDonald, Sean C.; Hollomon, Jonathan B.

    2005-08-01

    A joint NREL, ORNL, and PNNL team conducted market analysis to help inform DOE/EERE's Weatherization and Intergovernmental Program planning and management decisions. This chapter presents the results of the market analysis for the Buildings sector.

  16. Helping clients build credit

    OpenAIRE

    Vikki Frank

    2007-01-01

    Until now people who repaid loans from community groups had not been on credit bureaus’ radar. Now Credit Builders Alliance is partnering with Experian to help clients of community lenders build strong credit histories.

  17. Mobile augmented reality in support of building damage and safety assessment

    OpenAIRE

    Kim, W.; Kerle, N.; M. Gerke

    2016-01-01

    Rapid and accurate assessment of the state of buildings in the aftermath of a disaster event is critical for an effective and timely response. For rapid damage assessment of buildings, the utility of remote sensing (RS) technology has been widely researched, with focus on a range of platforms and sensors. However, RS-based approaches still have limitations to assess structural integrity and the specific damage status of individual buildings. Structural integrity refers to th...

  18. Treatment Conditions of Building Wastes in China and Its Integrated Management Measures

    Institute of Scientific and Technical Information of China (English)

    Liu Dan; Zha Kun; Li Qibin

    2006-01-01

    The status of utilization and disposal of the building wastes are introduced on the basis of analysis of its compositions, generation and effects on urban environment. The basic framework of the integrated building waste management, including control of the sources, reduction of the integrated process and final disposal, are proposed in view of the problems existing in recovery of the building wastes and the experiences from the developed countries.

  19. Building Materials in Arctic Climate

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede

    2005-01-01

    Building in the artic requires special attention on the appropriateness of building materials. The harsh climate makes execution difficult and sets unusual requirements for the pure material properties. In addition, there is a lack of choice of good, natural building materials in the arctic. This...... results in high transport costs. The building materials situation in Greenland may potentially be improved by intensifying the reuse of building materials or by promoting the local production of building materials....

  20. Building Services Systems

    DEFF Research Database (Denmark)

    Zinzi, Michele; Romeo, Carlo; Thomsen, Kirsten Engelund;

    2015-01-01

    This guideline on Building Services Systems is one of four guidelines produced by the School of the Future project. The other three guidelines cover: Building Construction Elements, Improved Indoor Environmental Quality and Concepts for Zero Emission Schools. This guideline consists of the...... description of 5 main technologies: condensing boilers, heat pumps, ventilation systems, lighting and photovoltaic systems. For each technology chapter there is the same content list: an introduction, a brief technology description, some advantages and disadvantages, market penetration and utilisation, energy...

  1. Plataforma smart building

    OpenAIRE

    Cidrera Lopez, Alain

    2013-01-01

    The overall project is a system (hardware + software) that allows monitoring and control in a building / office different security systems, energy, communications, home automation, PKI's overall business that will increase all the efficiency of the building and the business and ensure the continuity of it. My participation in this Project will mainly focus on the development of hardware components, monitoring and control system (home automation, energy, safety control elements ...) and softwa...

  2. Green buildings pay

    DEFF Research Database (Denmark)

    Naboni, Emanuele; Edwards, Brian

    2012-01-01

    The new edition of ‘Green Buildings Pay’ authored by Brian Edwards and Emanuele Naboni explores the business and professional benefits which derive from architectural design driven by sustainability. With a new sub-title ‘Green Buildings Pay: design, productivity and ecology’ the book argues....... Branding via LEED and BREEAM has taken green ideas to China and other emerging economies. The globalization of sustainability and of architectural practice is an important strand of the new edition....

  3. Building Peaceful Borders

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    China's efforts to build a harmonious world begin with establishing peaceful borders with its neighbors China's recent contribution to the world of international relations is the promotion of "building a harmonious world together," put forward by President Hu Jintao at the 60th anniversary of the UN in September 2005. As the core of the country's peaceful foreign policy in the new era, this approach has been well received and widely discussed in the international community. Meanwhile, Chinese foreign pol...

  4. 324 Building fire hazards analysis implementation plan

    International Nuclear Information System (INIS)

    In March 1998, the 324 Building Fire Hazards Analysis (FHA) (Reference 1) was approved by the U S. Department of Energy, Richland Operations Office (DOE-RL) for implementation by B and W Hanford Company (BWHC). The purpose of the FHA was to identify gaps in compliance with DOE Order 5480.7A (Reference 2) and Richland Operations Office Implementation Directive (RLID) 5480.7 (Reference 3), especially in regard to loss limitation. The FHA identified compliance gaps in six areas and provided 20 recommendations to bring the 324 Building into compliance with DOE Order 5480 7A. Additionally, one observation was provided. A status is provided for each recommendation in this document. The actions for recommendations associated with the safety related part of the 324 Building and operation of the cells and support areas were evaluated using the Unreviewed Safety Question (USQ) process BWHC will use this Implementation Plan to bring the 324 Building and its operation into compliance with DOE Order 5480 7A and RLID 5480.7

  5. 324 Building fire hazards analysis implementation plan

    International Nuclear Information System (INIS)

    In March 1998, the 324 Building Fire Hazards Analysis (FHA) (Reference 1) was approved by the US Department of Energy, Richland Operations Office (DOE-RL) for implementation by B and W Hanford Company (BWHC). The purpose of the FHA was to identify gaps in compliance with DOE Order 5480.7A (Reference 2) and Richland Operations Office Implementation Directive (RLID) 5480.7 (Reference 3), especially in regard to loss limitation. The FHA identified compliance gaps in six areas and provided 20 recommendations to bring the 324 Building into compliance with DOE Order 5480.7A. Additionally, one observation was provided. To date, four of the recommendations and the one observation have been completed. Actions identified for seven of the recommendations are currently in progress. Exemption requests will be transmitted to DOE-RL for three of the recommendations. Six of the recommendations are related to future shut down activities of the facility and the corrective actions are not being addressed as part of this plan. The actions for recommendations associated with the safety related part of the 324 Building and operation of the cells and support areas were evaluated using the Unreviewed Safety Question (USQ) process. Major Life Safety Code concerns have been corrected. The status of the recommendations and actions was confirmed during the July 1998 Fire Protection Assessment. BVMC will use this Implementation Plan to bring the 324 Building and its operation into compliance with DOE Order 5480.7A and RLID 5480.7

  6. Building Services Requests Subsystem (BSRS)

    Data.gov (United States)

    Department of Transportation — Lotus Notes workflow application used for the submission, processing, tracking and reporting of building service related requiests. Enables regional office building...

  7. Deadline Compliance Status Reports

    Data.gov (United States)

    Department of Housing and Urban Development — These monthly Deadline Compliance Status Reports assist Participating Jurisdictions and HUD Field Offices in monitoring compliance with the 2-year commitment and...

  8. Partial motor status epilepticus

    OpenAIRE

    Gilberto Rebello de Mattos; José C. Rollemberg Filho

    1992-01-01

    We report the case of a young female patient with photosensitive primary epilepsy who presented partial motor status epilepticus provoked by the act of shutting the eyes. Clinical, EEG and neuroimage data are presented and discussed.

  9. Topical report review status

    International Nuclear Information System (INIS)

    A Topical Report Review Status is scheduled to be published semi-annually. The primary purpose of this document is to provide periodic progress reports of on-going topical report reviews, to identify those topical reports for which the Nuclear Regulatory Commission (NRC) staff review has been completed and, to the extent practicable, to provide NRC management with sufficient information regarding the conduct of the topical report program to permit taking whatever actions deemed necessary or appropriate. This document is also intended to be a source of information to NRC Licensing Project Managers and other NRC personnel regarding the status of topical reports which may be referenced in applications for which they have responsibility. This status report is published primarily for internal NRC use in managing the topical report program, but is also used by NRC to advise the industry of report review status

  10. NAIP Status Maps Gallery

    Data.gov (United States)

    Farm Service Agency, Department of Agriculture — NAIP Status Maps Gallery. These maps illustrate what aerial imagery collection is planned, whats been collected, when it is available and how it is available. These...

  11. STATUS GIZI DAN STATUS KESEHATAN SUKU BADUY

    Directory of Open Access Journals (Sweden)

    Faisal Anwar

    2012-03-01

    Full Text Available 800x600 Normal 0 false false false IN X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} The objectives of the study were: (1 To analyze the socio-economic and demographic characteristics of Baduy people; (2 To analyze the health status and nutritional status of Baduy people and its influential factors. This research is an explorative and descriptive study on the socio-cultural aspects of food system. The data were collected through a direct interview and discussion with respondents as well as a direct observation at the location of respondents. A sample size of 338 households was drawn from the population. To obtain the data on the cultural aspects, history and  socio aspect of food, in-depth interviews was conducted with 19 key persons. The study was last for 12 months. In Outer Baduy, the factors significantly related to nutritional status are age, number of household size, income, nutritional knowledge, and wife’s ability to read. In Moslem Baduy, only age and income are related to the nutritional status of children. In Moslem Baduy and the Outer Baduy, the correlation between age and W/A or W/H is similar: namely, the higher the age, the lower would the Z-score for the W/A or W/H. The income is significantly correlated to the child nutritional status according to Z-score for W/A with a high correlation coefficient, that is, 0.61. This means that the higher the income, the higher would be the Z-score value for the W/A.  The distribution of adults according to BMI classification in Outer Baduy it shows that 12.7% husbands and 17.6% wives are thin (wasted, while the

  12. COMMUNICATION ABOUT SOCIAL STATUS

    OpenAIRE

    Fernald, Russell D.

    2014-01-01

    Dominance hierarchies are ubiquitous in social species and serve to organize social systems. Social and sexual status is communicated directly among animals via sensory systems evolved in the particular species. Such signals may be chemical, visual, auditory, postural or a combination of signals. In most species, status is initially established through physical conflict between individuals that leads to ritualized conflict or threats, reducing possibly dangerous results of fighting. Many of t...

  13. Status of numerical relativity

    Indian Academy of Sciences (India)

    Masaru Shibata

    2004-10-01

    I describe the current status of numerical relativity from my personal point of view. Here, I focus mainly on explaining the numerical implementations necessary for simulating general relativistic phenomena such as the merger of compact binaries and stellar collapse, emphasizing the well-developed current status of such implementations that enable simulations for several astrophysical phenomena. Some of our latest results for simulation of binary neutron star mergers are briefly presented.

  14. STATUS EPILEPTICUS: A REVIEW

    Directory of Open Access Journals (Sweden)

    B. Adibeik

    2009-01-01

    Full Text Available ObjectiveStatus Epilepticus (SE has been described as a series of major motor seizure without recovery of consciousness between seizures.SE is a medical emergency that requires prompt diagnosis and appropriate treatment.In this article we shall conclude history, epidemiology, etiology, risk factors, thebest management as well as the prognosis of the condition.Keywords:Status Epilepticus (SE, adults, children, neonates.

  15. Status of ADSW 2005

    DEFF Research Database (Denmark)

    Hartmann, H.; Ahring, Birgitte Kiær

    2006-01-01

    The status of the recent developments in anaerobic digestion of solid waste (ADSW) is outlined on the basis of a selection of papers presented at the 4(th) International Symposium on ADSW 2005.......The status of the recent developments in anaerobic digestion of solid waste (ADSW) is outlined on the basis of a selection of papers presented at the 4(th) International Symposium on ADSW 2005....

  16. RPC-PET: Status and perspectives

    International Nuclear Information System (INIS)

    The status of the resistive plate chamber (RPC)-PET technology for small animals is briefly reviewed and its sensitivity performance for human PET studied through Monte-Carlo simulations. The cost-effectiveness of these detectors and their very good timing characteristics open the possibility to build affordable Time of Flight (TOF)-PET systems with very large fields of view. Simulations suggest that the sensitivity of such systems for human whole-body screening, under reasonable assumptions, may exceed the present crystal-based PET technology by a factor up to 20

  17. RPC-PET: Status and perspectives

    Energy Technology Data Exchange (ETDEWEB)

    Couceiro, M. [LIP, Laboratorio de Instrumentacao e Fisica Experimental de Particulas, 3004-516 Coimbra (Portugal); ISEC, Instituto Superior de Engenharia de Coimbra, 3031-199 Coimbra (Portugal); Blanco, A. [LIP, Laboratorio de Instrumentacao e Fisica Experimental de Particulas, 3004-516 Coimbra (Portugal); Ferreira, Nuno C. [IBILI, Instituto Biomedico de Investigacao de Luz e Imagem, Faculty of Medicine, 3004-516 Coimbra (Portugal); Ferreira Marques, R. [LIP, Laboratorio de Instrumentacao e Fisica Experimental de Particulas, 3004-516 Coimbra (Portugal); Departamento de Fisica, Universidade de Coimbra, 3004-516 Coimbra (Portugal); Fonte, P. [LIP, Laboratorio de Instrumentacao e Fisica Experimental de Particulas, 3004-516 Coimbra (Portugal); ISEC, Instituto Superior de Engenharia de Coimbra, 3031-199 Coimbra (Portugal)], E-mail: fonte@coimbra.lip.pt; Lopes, L. [LIP, Laboratorio de Instrumentacao e Fisica Experimental de Particulas, 3004-516 Coimbra (Portugal)

    2007-10-01

    The status of the resistive plate chamber (RPC)-PET technology for small animals is briefly reviewed and its sensitivity performance for human PET studied through Monte-Carlo simulations. The cost-effectiveness of these detectors and their very good timing characteristics open the possibility to build affordable Time of Flight (TOF)-PET systems with very large fields of view. Simulations suggest that the sensitivity of such systems for human whole-body screening, under reasonable assumptions, may exceed the present crystal-based PET technology by a factor up to 20.

  18. Should Public Buildings Be Exclusive? A Study of Selected Institutional Buildings in Minna, Niger State.

    Directory of Open Access Journals (Sweden)

    Oyetola, S.A

    2015-03-01

    Full Text Available Some individuals are born with a deformity also known as disability whereas others may become permanently or temporarily disabled over the course of their lives. Buildings should not be made to judge who comes in and goes out of its spaces. A good design must be accessible to all individuals, especially when discussing public buildings. An educational building is a public building and “education for all” is a common dictum that refers to all individuals irrespective of current status. Disabled individuals especially those in wheelchairs have special needs and requirements however, most Institutional buildings do not portray this equality with regards to their design; instead these designs ostracize individuals with disabilities. A survey was carried out on the existing special educational facility and forty four (44 randomly selected institutions of learning located in Minna, the capital of Niger State. They were further categorised based on funding; Federal, state or privately funded institutions. The survey showed that individuals with physical disabilities in Minna were not attending the special educational school and even if they were, facilities were not put in place to accommodate them also, despite the support by the Nigerian government on the equalisation of opportunities for people with disabilities, the public educational system have yet to factor in or retrofit designs to suit disabled individuals in their designs. This paper further highlighted these abnormalities in design and probable causes and concluded by recommending possible solutions.

  19. Development of two Danish building typologies for residential buildings

    DEFF Research Database (Denmark)

    Kragh, Jesper; Wittchen, Kim Bjarne

    2014-01-01

    building types: single-family houses, terraced houses and blocks of flats. Each main building type is presented for nine periods representing age, typical building tradition and insulation levels. Finally, an energy balance model of the residential building stock was devised to validate the average...

  20. Status of the DIRAC Project

    International Nuclear Information System (INIS)

    The DIRAC Project was initiated to provide a data processing system for the LHCb Experiment at CERN. It provides all the necessary functionality and performance to satisfy the current and projected future requirements of the LHCb Computing Model. A considerable restructuring of the DIRAC software was undertaken in order to turn it into a general purpose framework for building distributed computing systems that can be used by various user communities in High Energy Physics and other scientific application domains. The CLIC and ILC-SID detector projects started to use DIRAC for their data production system. The Belle Collaboration at KEK, Japan, has adopted the Computing Model based on the DIRAC system for its second phase starting in 2015. The CTA Collaboration uses DIRAC for the data analysis tasks. A large number of other experiments are starting to use DIRAC or are evaluating this solution for their data processing tasks. DIRAC services are included as part of the production infrastructure of the GISELA Latin America grid. Similar services are provided for the users of the France-Grilles and IBERGrid National Grid Initiatives in France and Spain respectively. The new communities using DIRAC started to provide important contributions to its functionality. Among recent additions can be mentioned the support of the Amazon EC2 computing resources as well as other Cloud management systems; a versatile File Replica Catalog with File Metadata capabilities; support for running MPI jobs in the pilot based Workload Management System. Integration with existing application Web Portals, like WS-PGRADE, is demonstrated. In this paper we will describe the current status of the DIRAC Project, recent developments of its framework and functionality as well as the status of the rapidly evolving community of the DIRAC users.

  1. Safety system status monitoring

    International Nuclear Information System (INIS)

    The Pacific Northwest Laboratory has studied the safety aspects of monitoring the preoperational status of safety systems in nuclear power plants. The goals of the study were to assess for the NRC the effectiveness of current monitoring systems and procedures, to develop near-term guidelines for reducing human errors associated with monitoring safety system status, and to recommend a regulatory position on this issue. A review of safety system status monitoring practices indicated that current systems and procedures do not adequately aid control room operators in monitoring safety system status. This is true even of some systems and procedures installed to meet existing regulatory guidelines (Regulatory Guide 1.47). In consequence, this report suggests acceptance criteria for meeting the functional requirements of an adequate system for monitoring safety system status. Also suggested are near-term guidelines that could reduce the likelihood of human errors in specific, high-priority status monitoring tasks. It is recommended that (1) Regulatory Guide 1.47 be revised to address these acceptance criteria, and (2) the revised Regulatory Guide 1.47 be applied to all plants, including those built since the issuance of the original Regulatory Guide

  2. Building air exhaustion device

    International Nuclear Information System (INIS)

    An opening is formed on the side wall of a building such as of a nuclear power plant, and a blow out panel is held (supported) by a clip for closing the opening. A large-diameter pipeline is connected at one end to the opening so as to cover the blow out panel, and immersed at the other end in a pool water. When a pipeline such as of main steam pipelines is ruptured in the building, high temperature and high pressure coolants are flown out from the ruptured port, and the pressure in the building is elevated. The blow out panel falls off from the side of the building by the elevation of the pressure in the building. Steams or compressed air discharged from the opening is introduced to the pool through the large diameter pipeline, then the steams are condensed by the pool water and radioactive materials contained in the condensed steams are kept in the pool water. Radioactive materials contained in the released compression air are also removed into the pool water. (I.N.)

  3. SOLAR EFFECTS ON BUILDING DESIGN.

    Science.gov (United States)

    Building Research Inst., Inc., Washington, DC.

    A REPORT OF A PROGRAM HELD AS PART OF THE BUILDING RESEARCH INSTITUTE 1962 SPRING CONFERENCE ON THE SOLAR EFFECTS ON BUILDING DESIGN. TOPICS DISCUSSED ARE--(1) SOLAR ENERGY DATA APPLICABLE TO BUILDING DESIGN, (2) THERMAL EFFECTS OF SOLAR RADIATION ON MAN, (3) SOLAR EFFECTS ON ARCHITECTURE, (4) SOLAR EFFECTS ON BUILDING COSTS, (5) SELECTION OF…

  4. Automated model building

    CERN Document Server

    Caferra, Ricardo; Peltier, Nicholas

    2004-01-01

    This is the first book on automated model building, a discipline of automated deduction that is of growing importance Although models and their construction are important per se, automated model building has appeared as a natural enrichment of automated deduction, especially in the attempt to capture the human way of reasoning The book provides an historical overview of the field of automated deduction, and presents the foundations of different existing approaches to model construction, in particular those developed by the authors Finite and infinite model building techniques are presented The main emphasis is on calculi-based methods, and relevant practical results are provided The book is of interest to researchers and graduate students in computer science, computational logic and artificial intelligence It can also be used as a textbook in advanced undergraduate courses

  5. Buildings for advanced technology

    CERN Document Server

    Teague, E; Murday, James

    2015-01-01

    This book deals with the design and construction of buildings for nanoscale science and engineering research. The information provided in this book is useful for designing and constructing buildings for such advanced technologies as nanotechnology, nanoelectronics and biotechnology. The book outlines the technology challenges unique to each of the building environmental challenges outlined below and provides best practices and examples of engineering approaches to address them: • Establishing and maintaining critical environments: temperature, humidity, and pressure • Structural vibration isolation • Airborne vibration isolation (acoustic noise) • Isolation of mechanical equipment-generated vibration/acoustic noise • Cost-effective power conditioning • Grounding facilities for low electrical interference • Electromagnetic interference (EMI)/Radio frequency interference (RFI) isolation • Airborne particulate contamination • Airborne organic and chemical contamination • Environment, safety a...

  6. On building Information Warehouses

    CERN Document Server

    Laha, Arijit

    2009-01-01

    One of the most important goals of information management (IM) is supporting the knowledge workers in performing their works. In this paper we examine issues of relevance, linkage and provenance of information, as accessed and used by the knowledge workers. These are usually not adequately addressed in most of the IT based solutions for IM. Here we propose a non-conventional approach for building information systems for supporting the knowledge workers which addresses these issues. The approach leads to the ideas of building Information Warehouses (IW) and Knowledge work Support Systems (KwSS). Such systems can open up potential for building innovative applications of significant impact, including those capable of helping organizations in implementing processes for double-loop learning.

  7. Zero Energy Building

    DEFF Research Database (Denmark)

    Marszal, Anna Joanna; Heiselberg, Per; Bourrelle, J.S.;

    2011-01-01

    , (4) the type of energy balance, (5) the accepted renewable energy supply options, (6) the connection to the energy infrastructure and (7) the requirements for the energy efficiency, the indoor climate and in case of gird connected ZEB for the building–grid interaction. This paper focuses on the......The concept of Zero Energy Building (ZEB) has gained wide international attention during last few years and is now seen as the future target for the design of buildings. However, before being fully implemented in the national building codes and international standards, the ZEB concept requires...... clear and consistent definition and a commonly agreed energy calculation methodology. The most important issues that should be given special attention before developing a new ZEB definition are: (1) the metric of the balance, (2) the balancing period, (3) the type of energy use included in the balance...

  8. Building brains for bodies

    Science.gov (United States)

    Brooks, Rodney Allen; Stein, Lynn Andrea

    1994-01-01

    We describe a project to capitalize on newly available levels of computational resources in order to understand human cognition. We will build an integrated physical system including vision, sound input and output, and dextrous manipulation, all controlled by a continuously operating large scale parallel MIMD computer. The resulting system will learn to 'think' by building on its bodily experiences to accomplish progressively more abstract tasks. Past experience suggests that in attempting to build such an integrated system we will have to fundamentally change the way artificial intelligence, cognitive science, linguistics, and philosophy think about the organization of intelligence. We expect to be able to better reconcile the theories that will be developed with current work in neuroscience.

  9. 308 Building zone I stabilization and confinement

    International Nuclear Information System (INIS)

    The 308 Building located on the Hanford Site near Richland, Washington, is currently in transition to shutdown status. After this transition is complete, the facility will be maintained/surveilled and given to the U.S. Department of Energy Office of Facility Transition and Management (EM-60) for utilization, remedial action, or decontamination and decommissioning (D ampersand D). This may require that the facility be maintained in the shutdown status for as long as 30 yrs. To date, all of the special nuclear material (SNM) has been removed, potential fuel supply equipment preserved, surplus materials and equipment excessed, and enclosure cleanup and stabilization completed. A major activity in support of the 308 Building shutdown was the cleanup and stabilization of the enclosures and surface contamination areas. This document discusses the specific designs, processes, and methods used to stabilize and confine the radiological material within the enclosure and exhaust ducts to allow the shutdown of the active support systems. The process and designs employed were effective, yet simple, and maximized the use of current technologies and commercial products

  10. Carbon Efficient Building Solutions

    Directory of Open Access Journals (Sweden)

    Pellervo Matilainen

    2010-03-01

    Full Text Available Traditionally, the Finnish legislation have focused on energy use and especially on energy used for heating space in buildings. However, in many cases this does not lead to the optimal concept in respect to minimizing green house gases. This paper studies how CO2 emission levels are affected by different measures to reduce energy use in buildings. This paper presents two real apartment buildings with different options of energy efficiency and power sources. The calculations clearly show that in the future electricity and domestic hot water use will have high importance in respect to energy efficiency, and therefore also CO2 equivalent (eq emissions. The importance increases when the energy efficiency of the building increases. There are big differences between average Finnish production and individual power plants; CO2 eq emissions might nearly double depending on the energy source and the power plant type. Both a building with an efficient district heating as a power source, and a building with ground heat in addition to nuclear power electricity as a complimentary electricity source performed very similarly to each other in respect to CO2 eq emissions. However, it is dangerous to conclude that it is not important which energy source is chosen. If hypothetically, the use of district heating would dramatically drop, the primary energy factor and CO2 eq emissions from electricity would rise, which in turn would lead to the increase of the ground heat systems emissions. A problem in the yearly calculations is that the fact that it is very important, sometimes even crucial, when energy is needed, is always excluded.

  11. building integrated wind energy

    OpenAIRE

    Wang, Jialin

    2013-01-01

    In considering methods of reducing the emission of carbon dioxide; there is a growing interest for use of wind power at domestic building in U.K. But the technology of wind turbines development in building environment is more complicated than in open areas. Small wind turbines in suburban areas have been reported as having unsatisfactory energy output, but it is not clear whether this is due to insufficient wind resource or low turbine efficiency. The aim of this research is to discover wheth...

  12. Architecture Building Sustainability

    Institute of Scientific and Technical Information of China (English)

    DAVID HENDRICKSON

    2006-01-01

    @@ Leading architectural design and engineering firm, Skidmore,Owings, & Merrill (SOM), is renowned for pushing the envelope, masterminding some of the world's most cutting edge and enduring structural masterpieces - America's tallest building, the Sears Tower,in the firm's home city of Chicago, the 88-story Jinmao Tower in Shanghai, and the Freedom Tower in New York City, successor to the fallen World Trade Center complex,are among the well known projects in its building portfolio. SOM's next high profile assignment, the Pearl River Tower, in Guangzhou is one no less worthy of this tradition.

  13. PV cool-build

    Energy Technology Data Exchange (ETDEWEB)

    Cross, B.; Nuh, D.

    2004-07-01

    This report summarises the findings of a project to develop a method for calculating the operating temperature of building integrated photovoltaic (BIPV) modules/laminates which are estimated to operate above ambient temperature. The aim of the study was to minimise the temperature of the BIPV in order to increase the production of clean electricity. Details are given of a series of indoor experiments, computer modelling, and outdoor measurements. The production of a readily available, user-friendly design guide for architects and building designers is discussed.

  14. Building the perfect PC

    CERN Document Server

    Thompson, Robert Bruce

    2006-01-01

    This popular Build-It-Yourself (BIY) PC book covers everything you want to know about building your own system: Planning and picking out the right components, step-by-step instructions for assembling your perfect PC, and an insightful discussion of why you'd want to do it in the first place. Most big brand computers from HP, Dell and others use lower-quality components so they can meet their aggressive pricing targets. But component manufacturers also make high-quality parts that you can either purchase directly, or obtain through distributors and resellers. Consumers and corporations

  15. Building UIs with Wijmo

    CERN Document Server

    Zhang, Yuguang

    2013-01-01

    Written with an example-based approach, Building UIs with Wijmo leads you step by step through the implementation and customization of each library component and its associated resources. Reference tables of each configuration option, method, and event for each component are provided, alongside detailed explanations of how each widget is used.Building UIs with Wijmo is targeted at readers who are familiar with HTML, CSS, JavaScript, and jQuery, and have a basic understanding of web development. Although knowledge of jQuery UI is not mandatory, it would be a bonus as it is quite similar to Wijm

  16. Building global learning communities

    Directory of Open Access Journals (Sweden)

    Averill Gordon

    2013-09-01

    Full Text Available Within the background where education is increasingly driven by the economies of scale and research funding, we propose an alternative online open and connected framework (OOC for building global learning communities using mobile social media. We critique a three year action research case study involving building collaborative global learning communities around a community of practice of learning researchers and practitioners. The results include the development of a framework for utilising mobile social media to support collaborative curriculum development across international boundaries. We conclude that this framework is potentially transferrable to a range of educational contexts where the focus is upon student-generated mobile social media projects.

  17. Ecology Beyond Building

    DEFF Research Database (Denmark)

    Peters, Terri

    2011-01-01

    As the designers of the WWf building in Zeist, The Netherslands a CO2-neutral, self-sufficient office complex, RAU has set the bar for sustainable research and design. Guesteditor Terri Peters visited the firm's studio in Amsterdam to talk to principal Thomas Rau. As Peters relates, Rau prefers to...... put on the dwindling supply of raw materials rather than the immidiate problems of energy consumption for which there are solutions within reach. With the emphasis on a more far-reaching approach, he places buildings in a wider context of ecological thinking and systems....

  18. Towards green buildings: Glass as a building element-the use and misuse in the gulf region

    Energy Technology Data Exchange (ETDEWEB)

    Aboulnaga, Mohsen M. [College of Design and Applied Arts, Dubai University College, Dubai P.O. Box 14143 (United Arab Emirates)

    2006-04-15

    The recent economic growth in the Gulf region notably in Dubai, United Arab Emirates (UAE) has led to a colossal number of buildings that has been constructed in the past 5 years. In the last decade, a total glazed building's facades became the icon of Dubai. This large area of glazing in each facade needs protection against overheating and sun glare in summer. According to leader in energy and environmental design (LEED) glass selection becomes a main element in this equation to contribute towards achieving a green building. The aim of this paper is to investigate the problems associated with misuse of glass, as a building element in UAE particularly in Dubai. Inadequate design with ill-selected glass/glazing type may lead not only to poor daylighting in building interiors but also contribute significantly to fatigue, insomnia, seasonal affective disorder (SAD) and above all increase CO{sub 2} emission. The purpose of the study is to specify the required improvements to permit natural, 'free' daylight to filter through the building facade into interior space, especially with the right type of glass. This paper examines the status of buildings in Dubai in terms of glass type, visible light transmittance, reflection (out/in) and relative heat gain. A quantitative analysis is conducted to assess the impact of glass on the building users' performance in terms of daylight environment. A recent built high-rise office building was selected in the investigation to asses whether selected glass provide the recommended daylight factor (DF) and daylight level (DL) according to IES standards. The results revealed that most the glass/glazing was misused in 70% of buildings in intermediate and low performance groups. The DF and DD in the selected office building were unexpectedly tremendous and found far beyond the recommended level due to the use of spectrally selective glazing (clear on both sides). [Author].

  19. Sustainable Development and Green Buildings

    OpenAIRE

    Arijit Sinha; Rakesh Gupta; Andreja Kutnar

    2013-01-01

    Global sustainability goals have led to the development of the green building movement. The Green Building Program, stemming from the movement, has had unprecedented success as it provides a quantifiable metric to people’s efforts towards sustainable development. Sustainable development and green buildings are often used interchangeably. Although, sustainable development and green buildings are related, they are not the same. This paper provides an overview of how green building relates to su...

  20. Refractory status epilepticus

    Directory of Open Access Journals (Sweden)

    Sanjay P Singh

    2014-01-01

    Full Text Available Refractory status epilepticus is a potentially life-threatening medical emergency. It requires early diagnosis and treatment. There is a lack of consensus upon its semantic definition of whether it is status epilepticus that continues despite treatment with benzodiazepine and one antiepileptic medication (AED, i.e., Lorazepam + phenytoin. Others regard refractory status epilepticus as failure of benzodiazepine and 2 antiepileptic medications, i.e., Lorazepam + phenytoin + phenobarb. Up to 30% patients in SE fail to respond to two antiepileptic drugs (AEDs and 15% continue to have seizure activity despite use of three drugs. Mechanisms that have made the treatment even more challenging are GABA-R that is internalized during status epilepticus and upregulation of multidrug transporter proteins. All patients of refractory status epilepticus require continuous EEG monitoring. There are three main agents used in the treatment of RSE. These include pentobarbital or thiopental, midazolam and propofol. RSE was shown to result in mortality in 35% cases, 39.13% of patients were left with severe neurological deficits, while another 13% had mild neurological deficits.

  1. Sinoprobe Datacenter Development: Current Status

    Science.gov (United States)

    Guan, Y.; Dong, S.; Chen, Z.; Chen, G.; Cheng, M.

    2011-12-01

    The project of the Sinoprobe datacenter development is to build new IT infrastructures needed to store, visualize and manage all the data acquired by SinoProbe program.The SinoProbe data center is designed using service-oriented architecture (SOA) principles. More specifically, service component architecture (SCA) is used to implement sinoprobe data services. It also uses various advanced technologies such as Java/JEE for the platform, PostgresSQL/PostGIS for the data storage, ApacheDS for LDAP, CoachDB for the medadata storage, GeoServer for the GIS services, ExtJs and OpenLayer for the Ajax framework, and Apache Shiro for the security framework. Through the integration and development of various technologies used, the major services of the datacenter system are implemented including the security infrastructure services (user authentication and authorization), metadata services, data warehouse stores, data services, GIS services, and web portal. There are also visualization components including the development of a virtual globe to replace the currently used Google Earth. This poster presents the current status of the SinoProbe data center development, and the detailed discussion of the system.

  2. Social Status and Personality Traits

    OpenAIRE

    Alessandro Bucciol; Barbara Cavasso; Luca Zarri

    2014-01-01

    In this study we provide direct evidence on the relationship between social status and personality traits. Using survey data from the 2006-2012 waves of the HRS, we show that individuals’ self-perceived social status is associated with all the “Big Five” personality traits, after controlling for observable characteristics that arguably reflect one’s actual status. We also construct an objective status measure that in turn is influenced by personality traits. Objectively measured status is pos...

  3. Building Envelope for New Buildings and Energy Renovation of Old Buildings

    DEFF Research Database (Denmark)

    Rudbeck, Claus Christian

    The Building Envelope Project at Technical University of Denmark should, in coorporation with associated trade organizations, strengthen the development on the building envelope area with focus on heat, moisture and economy......The Building Envelope Project at Technical University of Denmark should, in coorporation with associated trade organizations, strengthen the development on the building envelope area with focus on heat, moisture and economy...

  4. Implementation of the MARSSIM to Evaluate the Final Status After Decommissioning Uranium Conversion Plant

    International Nuclear Information System (INIS)

    The decommissioning project of Uranium Conversion Plant was launched in 2001 and completed at the first half of 2011. The final stage of decommissioning process was the release of a site and building from regulatory control. KAERI carried out a final status survey based on the guidance provided in the MARSSIM (Multi-Agency Radiation Survey and Site Investigation Manual). The Uranium Conversion Plant was used to manufacture UO2 powder for CANDU fuel, the plant was contaminated only natural uranium. In this study, plans for the final status survey and release criteria for a site were established by applying the MARSSIM procedures. The survey design for the final status survey of the UCP site and buildings was carried out based on the statistical test of the results form scoping and characterization survey. The site and buildings were classified based on the potential contamination by using measured and calculated results. The results of the final status survey were satisfied the release criteria based on the measured data from a site and building. The summarized final status survey results are given in Figure 1 shows detail residual contamination level in Class 1. The results of the final status survey are sufficiently lower than the release criteria. The MARSSIM procedures were proved to be flexible, scientifically rigorous and cost effective for final status survey of decommissioning site and building. For the effective plan for the final status survey of the UCP site and its implementation, KAERI and its the regulation body are continuously discussing way to ensure the validation of the final status survey.

  5. Moisture conditions in buildings

    DEFF Research Database (Denmark)

    Rode, Carsten

    2012-01-01

    Growth of mould requires the presence of moisture at a certain high level. In a heated indoor environment such moisture levels occur only if there is a reason for the moisture supply. Such moisture can come from the use of the building, because of malfunctioning constructions, or it can be the...

  6. Building Migratory Bridges

    Science.gov (United States)

    Roy, Michael; Doss, Laurie K.

    2007-01-01

    The Building Migratory Bridges (BOMB) program--a collaboration between the Marvel wood School and Audubon Sharon in Connecticut and Conservation Research Education Action (CR EA), a U.S. not-for-profit in Panama--uses nontropical migratory bird research in the United States and Panama to demonstrate how negative environmental impacts in one…

  7. Building Background Knowledge

    Science.gov (United States)

    Neuman, Susan B.; Kaefer, Tanya; Pinkham, Ashley

    2014-01-01

    This article make a case for the importance of background knowledge in children's comprehension. It suggests that differences in background knowledge may account for differences in understanding text for low- and middle-income children. It then describes strategies for building background knowledge in the age of common core standards.

  8. Building with History

    DEFF Research Database (Denmark)

    Douglas-Jones, Rachel; Adams, Charlotte; Green, Adrian;

    2014-01-01

    Drawing on interdisciplinary research focusing on Durham University estate, we describe how buildings constructed as part of an eighteenth century transition to a high carbon coal-based economy, are used and understood by their current inhabitants. Applied heritage research has tended to focus on...

  9. Vedr.: Military capacity building

    DEFF Research Database (Denmark)

    Larsen, Josefine Kühnel; Struwe, Lars Bangert

    2013-01-01

    Kühnel Larsen and researcher Lars Bangert Struwe of CMS had organized a seminar in collaboration with Royal Danish Defense Colleg and the East African Security Governance Network. The seminar focused on some of the risks involved in Military capacity building and how these risks are dealt with from...

  10. Checklist for Physics Buildings.

    Science.gov (United States)

    American Inst. of Physics, New York, NY.

    This booklet was written to encourage close communication between architect and client and to assist planners of physics facilities in providing important features of building design. Some 300 items considered important are listed Also included is a list of 17 references related to facility construction (many available free of charge. A companion…

  11. Building a Twig Phylogeny

    Science.gov (United States)

    Flinn, Kathryn M.

    2015-01-01

    In this classroom activity, students build a phylogeny for woody plant species based on the morphology of their twigs. Using any available twigs, students can practice the process of cladistics to test evolutionary hypotheses for real organisms. They identify homologous characters, determine polarity through outgroup comparison, and construct a…

  12. Gaze Interactive Building Instructions

    DEFF Research Database (Denmark)

    Hansen, John Paulin; Ahmed, Zaheer; Mardanbeigi, Diako

    We combine eye tracking technology and mobile tablets to support hands-free interaction with digital building instructions. As a proof-of-concept we have developed a small interactive 3D environment where one can interact with digital blocks by gaze, keystroke and head gestures. Blocks may be moved...

  13. Future Green Buildings

    DEFF Research Database (Denmark)

    Mathiesen, Brian Vad; Drysdale, David; Lund, Henrik;

    an energy system integration perspective, heat savings, electricity savings, and user behavioural aspects as well as energy storage and household level flexibility. Many reports on green or sustainable buildings focus only on savings levels and disregard the cost of renewable energy production. Some reports...

  14. Radioactivity in building materials

    International Nuclear Information System (INIS)

    The present report, drawn up at the request of the former Minister of Public Health and Environmental Affairs of the Netherlands, discusses the potential radiological consequences for the population of the Netherlands of using waste materials as building materials in housing construction. (Auth.)

  15. Building Project Competence

    DEFF Research Database (Denmark)

    Pemsel, Sofia; Wiewiora, Anna

    This research investigates the development of project competence, and particularly, three related dynamic capabilities (shifting, adapting, leveraging) that contribute to project competence development. In doing so, we make use of the emerging literature on knowledge governance and theorize how...... of dynamic capability building promoting project competence development....

  16. Customer loyalty building

    OpenAIRE

    Nováková, Veronika

    2012-01-01

    This bachelor thesis focuses on the customer loyalty. It gives an example of CRM project which aims to build the loyalty of customers to some brand or product so the customer would return to the company and would be satisfied with all products and services he get.

  17. Building with Sand

    Science.gov (United States)

    Ashbrook, Peggy

    2010-01-01

    Children playing in damp sand invariably try to make a tower or a tunnel. By providing experiences with a variety of materials, alone and together, teachers set up the conditions for children to learn through their senses and ensure that a class approaches a topic with a common set of experiences to build on. Learning about the properties of…

  18. Building the quantum network

    International Nuclear Information System (INIS)

    We show how quantum key distribution (QKD) techniques can be employed within realistic, highly secure communications systems, using the internet architecture for a specific example. We also discuss how certain drawbacks in existing QKD point-to-point links can be mitigated by building QKD networks, where such networks can be composed of trusted relays or untrusted photonic switches. (author)

  19. References on Sustainable Buildings

    OpenAIRE

    Hui, Sam CM

    2005-01-01

    This web site is developed with the aim to promote sustainable design and planning of buildings. Selected references including books, reports, audio/visual materials and journals are listed. Most of the materials can be found in the HKU Libraries. To facilitate retrieval, links are provided to the library catalogue system for further information and study.

  20. Status of ATF, 2004

    International Nuclear Information System (INIS)

    Accelerator Test Facility (ATF) has already achieved the vertical emittance of GLC specification. In order to make the multi-bunch emittance achievement, high quality multi-bunch beam from photo-cathode rf gun was employed. The maximum allowable current was raised to 3 times more. From the study, it was found that the vacuum level of damping ring is related to the achieved vertical emittance. The ring scrubbing with high current accumulation made tail bunch emittance growth lower. We describe the status of multi-bunch emittance study together with the development status of the various emittance monitors and beam position monitors. (author)

  1. New Service Status Board

    CERN Multimedia

    2013-01-01

    On Monday 14 October, the Service Status Board for GS and IT will change. The new Status Board will be integrated with the CERN Service Portal and with the CERN Service Catalogue.   As of today, the SSB will display “Service Incidents”, “Planned Interventions” and “Service Changes”. References valid from 14 October: CERN SSB at https://cern.ch/ssb Computing SSB (previously IT SSB) at https://cern.ch/itssb   Nicole Cremel, IT and GS Service Management Support

  2. Pharmacotherapy for Status Epilepticus

    OpenAIRE

    Trinka, Eugen; Höfler, Julia; Leitinger, Markus; Brigo, Francesco

    2015-01-01

    Status epilepticus (SE) represents the most severe form of epilepsy. It is one of the most common neurologic emergencies, with an incidence of up to 61 per 100,000 per year and an estimated mortality of 20 %. Clinically, tonic-clonic convulsive SE is divided into four subsequent stages: early, established, refractory, and super-refractory. Pharmacotherapy of status epilepticus, especially of its later stages, represents an “evidence-free zone,” due to a lack of high-quality, controlled trials...

  3. FRIB Cryogenic Plant Status

    Energy Technology Data Exchange (ETDEWEB)

    Dixon, Kelly D. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Ganni, Venkatarao [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Knudsen, Peter N. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Casagranda, Fabio [Michigan State Univ., East Lansing, MI (United States)

    2015-12-01

    After practical changes were approved to the initial conceptual design of the cryogenic system for MSU FRIB and an agreement was made with JLab in 2012 to lead the design effort of the cryogenic plant, many activities are in place leading toward a cool-down of the linacs prior to 2018. This is mostly due to using similar equipment used at CHLII for the 12 GeV upgrade at JLab and an aggressive schedule maintained by the MSU Conventional Facilities department. Reported here is an updated status of the cryogenic plant, including the equipment procurement status, plant layout, facility equipment and project schedule.

  4. Deactivation of Building 7602

    International Nuclear Information System (INIS)

    The Department of Energy (DOE) has sponsored research and development programs in Building 7602 at Oak Ridge National Laboratory (ORNL) since 1984. This work focused on development of advanced technology for processing nuclear fuels. Building 7602 was used for engineering-scale tests using depleted and natural uranium to simulate the nuclear fuel. In April 1994 the DOE Office of Nuclear Energy (NE) sent supplemental FY 1994 guidance to ORNL stating that in FY 1995 and beyond, Building 7602 is considered surplus to NE programs and missions and shall be shut down (deactivated) and maintained in a radiologically and industrially safe condition with minimal surveillance and maintenance (S ampersand M). DOE-NE subsequently provided FY 1995 funding to support the deactivation activities. Deactivation of Building 7602 was initiated on October 1, 1994. The principal activity during the first quarter of FY 1995 was removal of process materials (chemicals and uranium) from the systems. The process systems were operated to achieve chemical solution concentrations needed for reuse or disposal of the solutions prior to removal of the materials from the systems. During this phase of deactivation the process materials processed and removed were: (1) Uranyl nitrate solution 30,178 L containing 4490 kg of uranium; (2) Nitric acid (neutralized) 9850 L containing less than 0.013 kg of uranium; (3) Organic solution 3346 L containing 265 kg of uranium; (4) Uranium oxide powder 95 kg; and (5) Miscellaneous chemicals. At the end of December 1994, the process systems and control systems were shut down and deactivated. Disposition of the process materials removed from the process systems in Building 7602 proved to be the most difficult part of the deactivation. An operational stand down and funding reductions at Y-12 prevented planned conversion of the uranyl nitrate solution to depleted uranium oxide powder. This led to disposal of the uranyl nitrate solution as waste

  5. Building characteristics that determine moisture in 105 Danish homes

    DEFF Research Database (Denmark)

    Knudsen, Sofie; Møller, Eva B.; Bräuner, Elvira

    2014-01-01

    . Geographical location, clothes drying indoors, lack of mechanical ventilation, high social status and spending more time indoors significantly increased the risk of indoor dampness. The variables associated with increased risk of dampness varied according to the method used to determine dampness. Measurements......Dampness in buildings is a risk factor for health issues and dampness increases the risk of indoor fungi contamination, which has likewise been identified as a risk factor for discomforts and illnesses. The aim of the present study is to elucidate building characteristics and occupancy behaviour...

  6. PROGRESS IN ENERGY EFFICIENT BUILDINGS

    Energy Technology Data Exchange (ETDEWEB)

    Wall, L.W.; Rosenfeld, A.H.

    1982-12-01

    Recent accomplishments in buildings energy research by the diverse groups in the Energy Efficient Buildings Program at Lawrence Berkeley Laboratory (LBL) are summarized. We review technological progress in the areas of ventilation and indoor air quality, buildings energy performance, computer modeling, windows, and artificial lighting. The need for actual consumption data to track accurately the improving energy efficiency of buildings is being addressed by the Buildings Energy Data (BED) Group at LBL. We summarize results to date from our Building Energy Use Compilation and Analysis (BECA) studies, which include time trends in the energy consumption of new commercial and new residential buildings, the measured savings being attained by both commercial and residential retrofits, and the cost-effectiveness of buildings energy conservation measures. We also examine recent comparisons of predicted vs. actual energy usage/savings, and present the case for building energy use labels.

  7. ITER buildings, site layout and safety

    International Nuclear Information System (INIS)

    Previous generic designs for the ITER buildings, plant layout and safety features are being adapted to French regulatory requirements as the next steps in preparation for constructing this experimental fusion facility. The characteristics of weather, environment, geology and seismic history, applicable to Cadarache, are being incorporated in the site layout and buildings' designs, as well as taking into account the special interests of local communities expressed through public hearings and debates. Currently, initial steps of site clearing are nearing completion, whilst temporary facilities are in preparation for subsequent construction activities such as earthworks, platform levelling, perimeter fences, and access control, as well as the introduction of essential services such as electric power, potable water, fire protection, temporary roads, sewage, and storm drains. As far as possible, areas are being set aside for the environmental protection of local trees, plants and insects. ITER, with its seven international partners, is coordinating the supply of the equipment and facilities through negotiated procurement sharing agreements. Nevertheless, the design, fabrication, construction and installation will be required to meet European codes and standards as well as to follow French safety and licensing procedures. This paper presents the current status of the building, site and licensing activites, in preparation for requesting the construction permit. (orig.)

  8. 327 Building fire hazards analysis implementation plan

    International Nuclear Information System (INIS)

    In March 1998, the 327 Building Fire Hazards Analysis (FRA) (Reference 1) was approved by the US Department of Energy, Richland Operations Office (DOE-RL) for implementation by B and W Hanford Company (B and WHC). The purpose of the FHA was to identify gaps in compliance with DOE Order 5480.7A (Reference 2) and Richland Operations Office Implementation Directive (RLID) 5480.7 (Reference 3), especially in regard to loss limitation. The FHA identified compliance gaps in five areas and provided nine recommendations (11 items) to bring the 327 Building into compliance. To date, actions for five of the 11 items have been completed. Exemption requests will be transmitted to DOE-RL for two of the items. Corrective actions have been identified for the remaining four items. The completed actions address combustible loading requirements associated with the operation of the cells and support areas. The status of the recommendations and actions was confirmed during the July 1998 Fire Protection Assessment. B and WHC will use this Implementation Plan to bring the 327 Building and its operation into compliance with DOE Order 5480.7A and RLID 5480.7

  9. Large-scale building integrated photovoltaics field trial. First technical report - installation phase

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-07-01

    This report summarises the results of the first eighteen months of the Large-Scale Building Integrated Photovoltaic Field Trial focussing on technical aspects. The project aims included increasing awareness and application of the technology, raising the UK capabilities in application of the technology, and assessing the potential for building integrated photovoltaics (BIPV). Details are given of technology choices; project organisation, cost, and status; and the evaluation criteria. Installations of BIPV described include University buildings, commercial centres, and a sports stadium, wildlife park, church hall, and district council building. Lessons learnt are discussed, and a further report covering monitoring aspects is planned.

  10. KAON: a status report

    International Nuclear Information System (INIS)

    TRIUMF is ready to build the KAON Factory. KAON is an accelerator system that consists of two fast cycling synchrotrons and three storage rings, with the existing 500 MeV H- cyclotron as injector. KAON will be a 30 GeV, 100μA system that will produce higher intensity beams than presently available of kaons, antiprotons, hadrons and neutrinos. It is planned to build the accelerator system over a period of 6 years after the beginning of construction at a cost of ∼Can$700M. (author). 3 refs., 5 figs., 2 tabs

  11. Status of the Medaustron Ion Beam Therapy centre

    CERN Document Server

    Dorda, U; Osmic, F; Benedikt, M

    2012-01-01

    MedAustron is a synchrotron based light-ion beam therapy centre for cancer treatment as well as for clinical and non-clinical research currently in its construction phase. The accelerator design is based on the CERN-PIMMS study and its technical implementation by CNAO. This paper presents a status overview over the whole project detailing the achieved progress of the building construction & technical infrastructure installation in Wiener Neustadt, Austria, as well as of the accelerator development, performed at CERN and partially at PSI. The design and procurement status and future planning of the various accelerator components is elaborated.

  12. Iraq: Country Status Report.

    Science.gov (United States)

    McFerren, Margaret

    A survey of the status of language usage in Iraq begins with an overview of the usage patterns of Arabic and Kurdish, especially in the context of recent political events and the agreement to make Kurdish a second official language in the Kurdish autonomous region, and to allow limited use of Kurdish in instruction and public communication. A…

  13. Iran: Country Status Report.

    Science.gov (United States)

    McFerren, Margaret

    A survey of the status of language usage in Iran begins with an overview of the usage pattern of Persian, the official language spoken by just over half the population, and the competing languages of six ethnic and linguistic minorities: Azerbaijani, Kurdish, Arabic, Gilaki, Luri-Bakhtiari, and Mazandarani. The development of language policy…

  14. Kurdish. Materials Status Report.

    Science.gov (United States)

    Center for Applied Linguistics, Washington, DC. Language/Area Reference Center.

    The materials status report for Kurdish is one of a series intended to provide the nonspecialist with a picture of the availability and quality of texts for teaching a given language to English speakers. Each report consists of: (1) a brief narrative description of the language, the areas where it is spoken, its major dialects, its writing system,…

  15. Status of PHOKHARA

    International Nuclear Information System (INIS)

    A review of the status of the Monte Carlo event generator PHOKHARA, developed for experiments using the radiative return method. The four-pion production in electron-positron annihilation and in τ-lepton decays and the narrow resonances studies are described.

  16. Mental status testing

    Science.gov (United States)

    ... Search Search MedlinePlus GO GO About MedlinePlus Site Map FAQs Contact Us Health Topics Drugs & Supplements Videos & Tools Español You Are Here: Home → Medical Encyclopedia → Mental status testing URL of this page: //medlineplus.gov/ ...

  17. Angola: Country Status Report.

    Science.gov (United States)

    Bruhn, Thea C.

    A survey of the status of language usage in Angola begins with an overview of the usage and distribution of Portuguese as the official language, and the four most significant native languages and dialects spoken there: Umbundu, Kimbundu, Kikongo, and Lunda-Chokwe. The introduction of Spanish through Cuban trainers, teachers, and military advisors…

  18. WOMEN STATUS IN INDIA

    OpenAIRE

    A. Prema

    2012-01-01

    This paper tries to explain the development of women movement in India and the status of women during the Vedic period and British period. It also tries to explain the position of women on the basis of socioeconomic – political empowerment.

  19. STATUS EPILEPTICUS: A REVIEW

    Directory of Open Access Journals (Sweden)

    B. Adibeik

    2008-10-01

    Full Text Available ObjectiveStatus Epilepticus (SE has been described as a series of major motor seizure without recovery of consciousness between seizures.SE is a medical emergency that requires prompt diagnosis and appropriate treatment.In this article we shall conclude history, epidemiology, etiology, risk factors, thebest management as well as the prognosis of the condition.

  20. Stellarator status, 1989

    International Nuclear Information System (INIS)

    The present status of stellarator experiments and recent progress in stellarator research (both experimental and theoretical) are reported by groups in the United States, the USSR, Japan, Australia, and the European Community (the Federal Republic of Germany and Spain). Experiments under construction and studies of large, next-generation stellarators are also described. 73 refs., 11 figs., 4 tabs

  1. The Status of CMS

    OpenAIRE

    Incandela, Joseph R.

    2007-01-01

    After a brief overview of the Compact Muon Solenoid (CMS) experiment, the status of construction, installation and commissioning is described. Very good progress has been achieved in the past year. Though many significant challenges still lie ahead, CMS should be ready for recording data from first collisions in the Large Hadron Collider (LHC) accelerator complex at CERN

  2. Nonconvulsive Status Epilepticus

    Directory of Open Access Journals (Sweden)

    Ayhan Aköz

    2014-08-01

    Full Text Available Status epilepticus (SE can be divided into two subgroups, convulsive status epilepticus (CSE and nonconvulsive status epilepticus (NCSE. NCSE is clinically characterized by recurrence or persistence of absence or complex partial seizures which unconsciousness persists. Seizures are lasted more than 30 minutes, and accompanied by mental and behavioral changes. Although the main feature is the change of level of consciousness, affective, memory, cognitive, speech, motor systems, behavioral and psychiatric disorders can be also seen. Electroencephalography (EEG is the single diagnostic method in this situation. NCSE constitutes approximately 25% of all SE, however it is thought that sometimes it is misdiagnosed and the incidence of NCSE may be higher. The causes are disorders of central nervous system (stroke, infection, trauma, tumor, and metabolic factors (hypoxia, renal diseases, drugs, failure to use antiepileptic drug. The treatment contains the standard therapy of SE. Short-acting benzodiazepines are preferred in initial treatment. For more resistant cases, loading of phenytoin is applied. If there is no response to treatment, midazolam and propofol additionally to barbiturates can be used. We aimed to present a case admitted to our ED with altered mental status and diagnosed as NCSE that is under-diagnosed.

  3. Fusion safety status report

    International Nuclear Information System (INIS)

    This report includes information on a) tritium handling and safety; b) activation product generation and release; c) lithium safety; d) superconducting magnet safety; e) operational safety and shielding; f) environmental impact; g) recycling, decommissioning and waste management; and h) accident analysis. Recommendations for high priority research and development are presented, as well as the current status in each area

  4. The energy performance of office buildings throughout their building process

    OpenAIRE

    Entrop, A.G.; Dewulf, G.P.M.R.; Wamelink, J.W.F.; Geraedts, R.P.; L. Volker

    2011-01-01

    Many innovative techniques and policy measures have been introduced to reduce energy consumption. Despite the high ambitions and societal pressures, the adoption rate of energy measures in office buildings is still low. Using adoption theories this paper provides a framework to analyse the adoption process of energy saving techniques in building processes. This framework is used to analyse the design and building processes of four Dutch office buildings. In these processes the roles of the st...

  5. Status of Jordan Research and Training Reactor Project

    International Nuclear Information System (INIS)

    The Jordan Atomic Energy Commission launched a construction project of Jordan's first nuclear reactor in 2010, following a contract with the consortium of Korea Atomic Energy Research Institute and Daewoo E and C. The Jordan Research and Training Reactor (JRTR), a 5 MW multipurpose research reactor, will serve as the focal point for a national nuclear technology center. This article presents the status of the JRTR Project and future plan as well. With the Construction Permit issued by the Jordan Nuclear Regulatory Commission, the construction work of reactor building and service building is underway, while over 95% of design work has been finished

  6. Building a Model Astrolabe

    CERN Document Server

    Ford, Dominic

    2012-01-01

    This paper presents a hands-on introduction to the medieval astrolabe, based around a working model which can be constructed from photocopies of the supplied figures. As well as describing how to assemble the model, I also provide a brief explanation of how each of its various parts might be used. The printed version of this paper includes only the parts needed to build a single model prepared for use at latitudes around 52{\\deg}N, but an accompanying electronic file archive includes equivalent images which can be used to build models prepared for use at any other latitude. The vector graphics scripts used to generate the models are also available for download, allowing customised astrolabes to be made.

  7. Radon in residential buildings

    International Nuclear Information System (INIS)

    For the investigation, a passive integrating radon dose meter developed at the KfK Karlsruhe was used. This institute also carried out the evaluation of all dose meters. The inquiry data were collected and statistically evaluated centrally by the Radiation Hygiene Institute of the German Health Authorities. Results obtained from almost 6.000 appartments show a distinct regional distribution of the measured values closely related to the geological conditions of the respected area. Surprisingly, there was little dependency on the building materials, with the exception of natural stone houses. The analysis showed that the structural characteristics of a building likely to influence the penetration of radon from the soil have a great effect on the Rn level. Generally, the frequency distribution of the measured values follows a logarithmic Gaussian distribution. Based on a median of 40 Bg/m3, the annual effective dose equivalent is about 1 mSv. (orig./HP)

  8. Building and using binoscopes

    CERN Document Server

    Butler, Norman

    2015-01-01

    Focusing on both homemade and commercial products, this book provides the reader with simple and straightforward information about the modelling and building of binoscopes. Binoscopes can be thought of as binoculars enlarged to the size of telescopes: essentially, a combination of the two. Constructing a binoscope is easier than most people think, but it still demands attention to detail and proper background knowledge. The author goes on to provide additional information about how to understand the products currently on the market, should the reader choose to purchase a binoscope instead of building one. Lastly, the book also compares binoscopes with telescopes in great detail, outlining the differences the reader can expect to see in the night sky from using both. The celestial views obtained with a binoscope, compared to a single telescope of the same aperture, are a very different experience and well worth the effort.

  9. Building synthetic memory

    OpenAIRE

    Inniss, Mara C.; Silver, Pamela A.

    2013-01-01

    Cellular memory – conversion of a transient signal into a sustained response – is a common feature of biological systems. Synthetic biologists aim to understand and reengineer such systems in a reliable and predictable manner. Synthetic memory circuits have been designed and built in vitro and in vivo based on diverse mechanisms such as oligonucleotide hybridization, recombination, transcription, phosphorylation, and RNA editing. Thus far, building these circuits has helped us explore the bas...

  10. Exploratory Model Building

    OpenAIRE

    Bhatnagar, Raj

    2013-01-01

    Some instances of creative thinking require an agent to build and test hypothetical theories. Such a reasoner needs to explore the space of not only those situations that have occurred in the past, but also those that are rationally conceivable. In this paper we present a formalism for exploring the space of conceivable situation-models for those domains in which the knowledge is primarily probabilistic in nature. The formalism seeks to construct consistent, minimal, and desirable situation-d...

  11. BUILD UP Skills Danmark

    DEFF Research Database (Denmark)

    Forsingdal, Charlotte Vartou; Lauridsen, Vagn Holk; Hougaard, Karsten Frøhlich;

    opfyldelsen af 2020-målene, skal de rette kompetencer inden for energief-fektivitet og brug af vedvarende energi være til stede blandt de udførende i bygge- og an-lægsbranchen. Det er på denne baggrund, at Europa-Kommissionen har igangsat Build Up Skills projektet på tværs af Europa. Formålet med denne...

  12. Towards universal university buildings

    OpenAIRE

    Heylighen, Ann; Michiels, Sam; Van Huffel, Sabine

    2006-01-01

    The paper presents a recent initiative at the Katholieke Universiteit Leuven (K.U.Leuven) that explores ways to stimulate knowledge exchange between building users and professionals. Within the context of the university’s diversity policy, students of the Architecture department and professionals of the Technical Services (TS) and Environment Health & Safety Service (EHS) team up with personnel and students with disabilities to assess the ‘universality’ of the campus. The aim i...

  13. Build America Bonds

    OpenAIRE

    Andrew Ang; Vineer Bhansali; Yuhang Xing

    2010-01-01

    Build America Bonds (BABs) are a new form of municipal financing introduced in 2009. Investors in BAB municipal bonds receive interest payments that are taxable, but issuers receive a subsidy from the U.S. Treasury. The BAB program has succeeded in lowering the cost of funding for state and local governments with BAB issuers obtaining finance 54 basis points lower, on average, compared to issuing regular municipal bonds. For institutional investors, BAB issue yields are 116 basis points highe...

  14. Thermal evaluation of buildings

    OpenAIRE

    Barajas, Luís M; Roset Calzada, Jaime; La Ferla, Giuseppe

    2015-01-01

    To COST ACTION TU 1104 "Smart Energy Regions" Prof. Aleksandra Djukic and Prof. Aleksandra Krstic-Furundzic of the Faculty of Architecture of the University of Belgrade, Serbia, that gave us the opportunity of be part of the training school imparted from Monday 20th to Thursday 23rd April 2015, where we can teach the topic. The convenience of the use of environmental building evaluation tools, to know design conditions and thermal behavior, by using bioclimatic strategies fo...

  15. NRC new sustainable building

    International Nuclear Information System (INIS)

    'Full text:' The National Research Council Institute For Fuel Cell Innovation is relocating to a purpose-built 71,343 sq. Ft. (6598 sq. M) Research, Testing, Evaluation, and Industry Incubation Facility in the spring of 2006. The new facility will contain Hydrogen-ready laboratories, the existing relocated Hydrogen Safe Environmental Test Chamber, a hydrogen vehicle maintenance bay, a hydrogen vehicle refuelling station, and the following demonstration projects and features: 1. A Ground Source Heat Pump: This long-proven natural-source heating and cooling technology to provide climate control for the new IFCI's atrium and galleria. It is being designed by Keen Engineering of North Vancouver, BC. 2. 5 KW Solid Oxide Fuel Cell System: Fuelled by natural gas and in the future, from biomass, the fuel cell will also produce approximately 15 kW of waste heat, which will be captured and used to supply heat for the building. The Solid Oxide Fuel Cell will be supplied by Fuel Cell Technologies in Kingston, ON. 3. LEED Building certification: Attaining LEED 'green building' certification is considered an important complement to the plans for the new NRC-IFCI, because it will provide respected third-party verification of government's commitment to efficient building design and construction. Project architects Bunting Coady of Vancouver, BC believe the IFCI has strong potential to earn gold LEED certification. 4. Photovoltaic hydrogen source for back-up power fuel cell system: A photovoltaic array will capture energy from sunlight to power an electrolyzer that will produce and store hydrogen for a PEM fuel cell emergency backup power system. The electrolyzer will be provided by Hydrogenics of Mississauga, ON. Photovoltaics are being designed and installed by the British Columbia Institute of Technology. (author)

  16. Work at Building 513

    CERN Multimedia

    IT Department

    2006-01-01

    As part of IT's preparations to meet the challenge of LHC computing, a new chilled water production unit is being constructed for the Computer Centre. The air conditioning work will start in mid-January and last until June 2006. During this period access to the car park of Building 513 will be restricted. Please consult the plan for details of the area affected by the work. With apologies for the inconvenience, IT Department

  17. Work at Building 513

    CERN Multimedia

    IT Department

    2006-01-01

    As part of IT's preparations to meet the challenge of LHC computing, a new chilled water production unit is being constructed for the Computer Centre. The air conditioning work will start in mid-January and last until June 2006. During this period, access to the car park of Building 513 will be restricted. Please consult the plan for details of the area affected by the work. With apologies for the inconvenience. IT Department

  18. Building a professional portfolio.

    OpenAIRE

    Arhippainen, Mikko

    2016-01-01

    Building a professional portfolio is a thesis report with buiding a professional portfolio for the author with a background in graphic design and event management with main interest on aesthetics side. This report describes the main process of selecting materials, planning and actually producing the portfolio. In addition to the portfolio there is a chapter with inspection on LinkedIn and other social medias when planning for jobsearch. Altogether it is many channels and a combination of ...

  19. Building Regional Competencies

    OpenAIRE

    Norus, Jesper

    2005-01-01

    This paper analyzes the foundations of regional knowledge and its long-term impact on the region’s companies’ and how a particular knowledge has developed an ability to stay competitive within a specific technological field. The case illustrates how the Copenhagen region has been able to develop a dominating position in the global market for industrial enzymes from 1870-2004. The case of industrial enzymes shows how a region has been able to build sustainable competitive advant...

  20. Building the Knowledge Economy

    OpenAIRE

    Čerić, Vlatko

    2001-01-01

    Generation and exploitation of knowledge became one of the most significant components in the new economy. This paper first investigates influence of information and communications technology on economy, with specific emphasis on Internet economy and electronic commerce. The paper then describes characteristics of the knowledge economy, discusses knowledge, presents main issues relevant for building of knowledge economy and gives an overview of the situation and perspectives of knowledge econ...

  1. Building for energy conservation

    Energy Technology Data Exchange (ETDEWEB)

    Burberry, P.

    1978-01-01

    Ways in which buildings may be designed to increase thermal efficiency are discussed, giving first of all examples of thermal design in relation to climate. How the building itself may be designed to take advantage of solar energy and the ways in which heat loss takes place are described; the effect of design variables such as siting, volume, and insulation is shown. The book also reviews the development of thermal regulations for health and comfort and, more recently, energy conservation. It discusses the possitilities and difficulties of legislation for energy saving. The UK regulations are given in detail together with descriptions of the FHA and ASHRAE recommendations for the USA and the lastest Scandinavian norms. The author argues that no significant cost need be involved in many of the aspects of thermal design, e.g., shape and fenestration; and that these factors should automatically be taken into account by designers. Even existing buildings can be adapted in various respects to save energy consumption. The book concludes with an explanation of calculation methods for U-values, heat loss, plant sizing, seasonal heat requirements, and other procedures, amply illustrated with tables and graphs.

  2. Capacity Building in Land Management

    DEFF Research Database (Denmark)

    Enemark, Stig; Ahene, Rexford

    2003-01-01

    There is a significant need for capacity building in the interdisciplinary area of land management especially in developing countries and countries in transition, to deal with the complex issues of building efficient land information systems and sustainable institutional infrastructures. Capacity...

  3. Allegheny County Building Footprint Locations

    Data.gov (United States)

    Allegheny County / City of Pittsburgh / Western PA Regional Data Center — This dataset contains photogrammetrically compiled roof outlines of buildings. All near orthogonal corners are square. Buildings that are less than 400 square feet...

  4. User Driven Innovative Building Design

    DEFF Research Database (Denmark)

    Christiansson, Per; Sørensen, Kristian Birch; Steffensen, K. G.;

    2009-01-01

    During recent years there has been an ever-increasing focus on the possibilities to change the building process to raise quality on the final building products as well as on the activities of actors involved in the building process. One reason for this interest is the new opportunities evolving due...... buildings in a collaborative/participative creative and innovative building design process. The AEC professionals also appreciate development, enhancement and to some extent formalization of existing methods for user involvement in the building process....... emphasis that the users are the key to next level of successful building projects. VICMET defines four spaces to support the activities in a innovative/creative design process; The Contextual Inquiry Space, the Conceptual Modeling and Game Space, the Functional Building Systems (FBS) Consolidation Space...

  5. The current state of computing in building design and construction

    DEFF Research Database (Denmark)

    Sørensen, Lars Schiøtt; Andersen, Tom

    An exhaustive IT-survey is made in the Danish construction industry in 1995. The outcome of this survey is outlined for a selected number of issues, such as number and types of CAD-systems, data base systems, networking etc. The survey shows, that the use of IT is massive. A detailed investigatio...... actual status. Finally, we conclude that there is a severe lack of awareness about AI-systems in the building sector....

  6. Building information models for astronomy projects

    Science.gov (United States)

    Ariño, Javier; Murga, Gaizka; Campo, Ramón; Eletxigerra, Iñigo; Ampuero, Pedro

    2012-09-01

    A Building Information Model is a digital representation of physical and functional characteristics of a building. BIMs represent the geometrical characteristics of the Building, but also properties like bills of quantities, definition of COTS components, status of material in the different stages of the project, project economic data, etc. The BIM methodology, which is well established in the Architecture Engineering and Construction (AEC) domain for conventional buildings, has been brought one step forward in its application for Astronomical/Scientific facilities. In these facilities steel/concrete structures have high dynamic and seismic requirements, M&E installations are complex and there is a large amount of special equipment and mechanisms involved as a fundamental part of the facility. The detail design definition is typically implemented by different design teams in specialized design software packages. In order to allow the coordinated work of different engineering teams, the overall model, and its associated engineering database, is progressively integrated using a coordination and roaming software which can be used before starting construction phase for checking interferences, planning the construction sequence, studying maintenance operation, reporting to the project office, etc. This integrated design & construction approach will allow to efficiently plan construction sequence (4D). This is a powerful tool to study and analyze in detail alternative construction sequences and ideally coordinate the work of different construction teams. In addition engineering, construction and operational database can be linked to the virtual model (6D), what gives to the end users a invaluable tool for the lifecycle management, as all the facility information can be easily accessed, added or replaced. This paper presents the BIM methodology as implemented by IDOM with the E-ELT and ATST Enclosures as application examples.

  7. ENERGY EFFICIENCY OF THE BUILDING

    OpenAIRE

    Bocharnikov, Dmitry

    2011-01-01

    The subject of bachelor’s thesis is about energy efficiency of the building. Much attention is being paid to energy saving problems all over the world. In the first part it theoretic base for thermal performance requirements of buildings. It includes main positions of Russian requirements for thermal performance. Also it is about general types of building envelope. The second part is about energy audit of buildings. In this part there is an energy efficiency assessment methodology. Energy eff...

  8. Capacity Building in Land Administration

    DEFF Research Database (Denmark)

    Enemark, Stig; Williamson, I

    2004-01-01

    Capacity building increasingly seen as a key component of land administration projects in developing and countries in transition undertaken by the international development banks and individual country development assistance agencies. However, the capacity building concept is often used within a...... should be dealt with as capacity building projects in themselves.    The article introduces a conceptual analytical framework that provides some guidance when dealing with capacity building for land administration in support of a broader land policy agenda....

  9. Upcoming renovations in Building 63

    CERN Multimedia

    2014-01-01

    La Poste will close its doors in Building 63 on Friday, 28 November. It moves to Building 510 and where it will open on 1 December (see picture).   UNIQA will close its HelpDesk in Building 63 on Wednesday, 26 November and will re-open the next day in Building 510. La Poste and UNIQA are expected to return to their renovated office space between April and May 2015.

  10. Hawaii-Okinawa Building Evaluations

    Energy Technology Data Exchange (ETDEWEB)

    Metzger, I.; Salasovich, J.

    2013-05-01

    NREL conducted energy evaluations at the Itoman City Hall building in Itoman, Okinawa Prefecture, Japan, and the Hawaii State Capitol building in Honolulu, Hawaii. This report summarizes the findings from the evaluations, including the best practices identified at each site and opportunities for improving energy efficiency and renewable energy. The findings from this evaluation are intended to inform energy efficient building design, energy efficiency technology, and management protocols for buildings in subtropical climates.

  11. Climate Responsive Buildings in China

    DEFF Research Database (Denmark)

    Haase, M.; Amato, A.; Heiselberg, Per

    2006-01-01

    There is a global need for a more sustainable building development. About 50% of energy is used in buildings indicating that buildings provide a considerable potential for operational energy savings. Studies were conducted with the following objectives: to perform a state-of-the-art review of res...

  12. Women Status and their Discrimination

    OpenAIRE

    PEŠKOVÁ, Pavlína

    2008-01-01

    My work deal with women status and their discrimination. Chapter one contains women status in different historical periods and development of their status to bigger equal with men. There is also written about present feminist trends. Chapter two is about women discrimination. There is about women´ job discrimination, job segregation according to gender and inequality in payment. There is also written about women status at home and unequal duties at home among family mates. Chapter three is ab...

  13. Associations of indoor carbon dioxide concentrations and environmental susceptibilities with mucous membrane and lower respiratory building related symptoms in the BASE study: Analyses of the 100 building dataset

    Energy Technology Data Exchange (ETDEWEB)

    Erdmann, Christine A.; Apte, Michael G.

    2003-09-01

    Using the US EPA 100 office-building BASE Study dataset, they conducted multivariate logistic regression analyses to quantify the relationship between indoor CO{sub 2} concentrations (dCO{sub 2}) and mucous membrane (MM) and lower respiratory system (LResp) building related symptoms, adjusting for age, sex, smoking status, presence of carpet in workspace, thermal exposure, relative humidity, and a marker for entrained automobile exhaust. In addition, they tested the hypothesis that certain environmentally-mediated health conditions (e.g., allergies and asthma) confer increased susceptibility to building related symptoms within office buildings. Adjusted odds ratios (ORs) for statistically significant, dose-dependent associations (p < 0.05) for dry eyes, sore throat, nose/sinus congestion, and wheeze symptoms with 100 ppm increases in dCO{sub 2} ranged from 1.1 to 1.2. These results suggest that increases in the ventilation rates per person among typical office buildings will, on average, reduce the prevalence of several building related symptoms by up to 70%, even when these buildings meet the existing ASHRAE ventilation standards for office buildings. Building occupants with certain environmentally-mediated health conditions are more likely to experience building related symptoms than those without these conditions (statistically significant ORs ranged from 2 to 11).

  14. Evolutionary status of Entamoeba

    Institute of Scientific and Technical Information of China (English)

    DONG Jiuhong; WEN Jianfan; XIN Dedong; LU Siqi

    2004-01-01

    In addition to its medical importance as parasitic pathogen, Entamoeba has aroused people's interest in its evolutionary status for a long time. Lacking mitochondrion and other intracellular organelles common to typical eukaryotes, Entamoeba and several other amitochondrial protozoans have been recognized as ancient pre-mitochondriate eukaryotes and named "archezoa", the most primitive extant eukaryotes. It was suggested that they might be living fossils that remained in a primitive stage of evolution before acquisition of organelles, lying close to the transition between prokaryotes and eukaryotes. However, recent studies revealed that Entamoeba contained an organelle, "crypton" or "mitosome", which was regarded as specialized or reductive mitochondrion. Relative molecular phylogenetic analyses also indicated the existence or the probable existence of mitochondrion in Entamoeba. Our phylogenetic analysis based on DNA topoisomerase II strongly suggested its divergence after some mitchondriate eukaryotes. Here, all these recent researches are reviewed and the evolutionary status of Entamoeba is discussed.

  15. Status of memory loss.

    LENUS (Irish Health Repository)

    Iyer, Parameswaran Mahadeva

    2012-01-01

    A 72-year-old woman presented with first onset of seizure with no prior history of cognitive dysfunction. EEG revealed focal non-convulsive status epilepticus. MRI brain showed a left temporal non-enhancing lesion. Temporal pole biopsy showed acute neuronal necrosis and astrocyte hyperplasia together with extensive amyloid plaques and neurofibrillary tangles. Perivascular oligodendroglial hyperplasia was present. Postmortem examination revealed extensive plaque and tangle disease. Perivascular oligodendroglial hyperplasia was limited to the left temporal area. The presence of focal perivascular oligodendroglial hyperplasia in the left temporal cortex, combined with extensive plaque and tangle disease may have contributed to the focal status epilepticus in this patient. Although the presence of focal perivascular oligodendroglial hyperplasia has been reported in cases of temporal lobe epilepsy, it has not been reported as a cause of seizure in patients with Alzheimer\\'s disease previously. Further studies for clinical-pathologic correlation would be required to confirm this hypothesis.

  16. Sibling Status Effects: Adult Expectations.

    Science.gov (United States)

    Baskett, Linda Musun

    1985-01-01

    This study attempted to determine what expectations or beliefs adults might hold about a child based on his or her sibling status alone. Ratings on 50 adjective pairs for each of three sibling status types, only, oldest, and youngest child, were assessed in relation to adult expectations, birth order, and parental status of rater. (Author/DST)

  17. Compliance with building energy regulations for new-build dwellings

    International Nuclear Information System (INIS)

    Despite increasingly stringent building energy regulations worldwide, non-compliance exists in practice. This paper examines the profile of compliance with building energy regulations for new-build dwellings. In total 404 new-build dwellings completed in the UK from 2006 to 2009 were investigated. Only a third of these dwellings were evidenced as being compliant with Building Regulations Part L (England and Wales). Such low compliance casts a serious concern over the achievability of the UK Government's target for all new-build homes to be ‘zero carbon’ from 2016. Clearly evidenced was a lack of knowledge of Part L and its compliance requirements among the supply and building control sides of new-build dwellings. The results also indicate that the compliance profile was influenced by factors including Standard Assessment Procedure (UK Government's methodology for energy efficiency) calculation submissions, learning and experience of builders and building controls with Part L, use of Part L1A checklist, the introduction of energy performance certificate (EPC), build method, dwelling type, and project size. Better compliance was associated with flats over houses and timber frame over masonry. The use of EPC and Part L1A checklist should be encouraged. Key to addressing the lack of compliance with building energy regulations is training. -- Highlights: ► There exists a lack of compliance, worldwide, with building energy regulations. ► The implementation of England and Wales building energy regulations is problematic. ► Training, learning and experience of builders and building control are critical. ► Energy performance certificate and Part L 2006 checklist helped achieve compliance. ► Flats achieved better compliance over houses; and timber frame over masonry.

  18. Status of the SLC

    International Nuclear Information System (INIS)

    The goals of the SLAC Linear Collider, SLC, are to develop the techniques of linear colliders and to do physics at and slightly above the energy necessary to produce the Z0. A short review is given of the physics goals of the SLC, followed by the status of the SLC and its detectors. Plans for accelerating polarized electrons at SLC are also discussed. 6 figs

  19. Status of fusion maintenance

    International Nuclear Information System (INIS)

    Effective maintenance will be an essential ingredient in determining fusion system productivity. This level of productivity will result only after close attention is paid to the entire system as an entity and appropriate integration of the elements is made. The status of fusion maintenance is reviewed in the context of the entire system. While there are many challenging developmental tasks ahead in fusion maintenance, the required technologies are available in several high-technology industries, including nuclear fission

  20. Tritium monitoring : present status

    International Nuclear Information System (INIS)

    The report summarizes the present status of techniques employed for the monitoring of tritium in water, air and other samples. A brief mention of the work done by numerous workers in the field, critical comments about the work and a fairly exhaustive list of references about the work done during the last 4 decades has been presented. On-line monitoring on real time basis in nuclear reactors is also discussed. (author). 83 refs., 10 refs., 2 tabs

  1. DUMAND II status report

    International Nuclear Information System (INIS)

    The scientific goals, design, capabilities, and status of the DUMAND II detector system are described. In June, 1989, the High Energy Physics Advisory Panel recommended support for construction of DUMAND II to the U.S. Department of Energy. Funding began in 1990, and prototype development for various detector subsystems is under way. Current plans include deployment of the shore cable, junction box and three strings of optical detector modules in 1992, and expansion to the full 9-string configuration in 1993

  2. MARS Flight Engineering Status

    Energy Technology Data Exchange (ETDEWEB)

    Fast, James E.; Dorow, Kevin E.; Morris, Scott J.; Thompson, Robert C.; Willett, Jesse A.

    2010-04-06

    The Multi-sensor Airborne Radiation Survey Flight Engineering project (MARS FE) has designed a high purity germanium (HPGe) crystal array for conducting a wide range of field measurements. In addition to the HPGe detector system, a platform-specific shock and vibration isolation system and environmental housing have been designed to support demonstration activities in a maritime environment on an Unmanned Surface Vehicle (USV). This report describes the status of the equipment as of the end of FY09.

  3. Experimental status of physics

    Indian Academy of Sciences (India)

    H Yamamoto

    2000-07-01

    In a short period of time, we will have a large amount of results from -factories including ones on CP violation. In this talk, we briefly review the current experimental status of -physics. After a quick description of -facilities, we divide this vast field into two categories: (1) weak interaction and QCD, (2) unitarity triangle and CP violation. Only a few critical items are selected in each category for the sake of time and space.

  4. QCDSP A status report

    CERN Document Server

    Chen, D; Christ, N H; Edwards, R G; Fleming, G R; Gara, A; Hansen, S; Jung, C; Kähler, A L; Kennedy, A D; Kilcup, G W; Luo, Y; Malureanu, C I; Mawhinney, Robert D; Parsons, H; Sexton, J C; Sui, C Z; Vranas, P M; Chen, Dong; Chen, Ping; Christ, Norman H.; Edwards, Robert G.; Fleming, George R.; Gara, Alan; Hansen, Sten; Jung, Chulwoo; Kaehler, Adrian L.; Kennedy, Anthony D.; Kilcup, Gregory W.; Luo, Yubing; Malureanu, Catalin I.; Mawhinney, Robert D.; Parsons, John; Sexton, James C.; Sui, ChengZhong; Vranas, Pavlos M.

    1997-01-01

    The QCDSP machine at Columbia University has grown to 2,048 nodes achieving a peak speed of 100 Gigaflops. Software for quenched and Hybrid Monte Carlo (HMC) evolution schemes has been developed for staggered fermions, with support for Wilson and clover fermions under development. We provide an overview of the runtime environment, the current status of the QCDSP construction program and preliminary results not presented elsewhere in these proceedings.

  5. CRESST - status and future

    International Nuclear Information System (INIS)

    We present results on WIMP dark matter interaction, obtained using cryogenic phonon-scintillation detectors. The targets are CaWO4 scintillating crystals with phonon sensors, while scintillation is detected with an associated cryogenic light detector. The combination of phonon and light signals leads to a strong suppression of nonnuclear recoil backgrounds. Results obtained before the upgrade of CRESST are presented and a status report on the upgrade itself is given

  6. QCDSP - a status report

    International Nuclear Information System (INIS)

    The QCDSP machine at Columbia University has grown to 2048 nodes achieving a peak speed of 100 Gigaflops. Software for quenched and hybrid Monte Carlo (HMC) evolution schemes has been developed for staggered fermions, with support for Wilson and clover fermions under development. We provide an overview of the runtime environment, the current status of the QCDSP construction program and preliminary results not presented elsewhere in these proceedings. (orig.)

  7. OPERA: Status and prospects

    Science.gov (United States)

    di Crescenzo, Antonia

    2014-03-01

    The Oscillation Project with Emulsion-tRacking Apparatus (OPERA) neutrino experiment was designed to perform a unique appearance measurement in the CNGS beam to confirm the oscillation mechanism in the atmospheric sector. Runs were successfully carried out from 2008 to 2012. The status of the analysis is reported and the topology and the kinematics of the first three ντ candidate events are described. A first result of the νμ→νe oscillation search is also presented.

  8. Uranium mining: Saskatchewan status

    International Nuclear Information System (INIS)

    This paper gives the status of uranium mining by Areva in Saskatchewan. Uranium production now meets 85% of world demand for power generation. 80% of world production of uranium comes from top 5 countries: Kazakhstan, Canada, Australia, Niger and Namibia. Saskatchewan is currently the only Canadian province with active uranium mines and mills and the largest exploration programs. Several mine projects are going through the environmental assessment process. Public opinion is in favour of mining activities in Saskatchewan.

  9. Status of VIRGO

    Science.gov (United States)

    Virgo Collaboration; Acernese, F.; Amico, P.; Arnaud, N.; Babusci, D.; Ballardin, G.; Barillé, R.; Barone, F.; Barsuglia, M.; Beauville, F.; Bellachia, F.; Bizouard, M. A.; Boccara, C.; Boget, D.; Bondu, F.; Bourgoin, C.; Bozzi, A.; Braccini, S.; Bradaschia, C.; Brillet, A.; Brisson, V.; Brocco, L.; Buskulic, D.; Cachenaut, J.; Calamai, G.; Calloni, E.; Campagna, E.; Casciano, C.; Cattuto, C.; Cavalier, F.; Cavaliere, S.; Cavalieri, R.; Cella, G.; Chassande-Mottin, E.; Chollet, F.; Cleva, F.; Cokelaer, T.; Conforto, G.; Cortese, S.; Coulon, J. P.; Cuoco, E.; Dattilo, V.; Y Davíd, P.; Davier, M.; De Rosa, M.; De Rosa, R.; Di Fiore, L.; Di Virgilio, A.; Dujardin, B.; Dominici, P.; Eleuteri, A.; Enard, D.; Evangelista, G.; Ferrante, I.; Fidecaro, F.; Fiori, I.; Flaminio, R.; Forest, D.; Fournier, J. D.; Fournier, L.; Frasca, S.; Frasconi, F.; Gammaitoni, L.; Ganau, P.; Gennai, A.; Gennaro, G.; Giacobone, L.; Giazotto, A.; Giordano, G.; Girard, C.; Gougoulat, G.; Guidi, G. M.; Heitmann, H.; Hello, P.; Hermel, R.; Heusse, P.; Holloway, L.; Honglie, F.; Iannarelli, M.; Journet, L.; Krecklbergh, S.; Lagrange, B.; La Penna, P.; Leliboux, M.; Lieunard, B.; Lomtadze, T.; Loriette, V.; Losurdo, G.; Loupias, M.; Mackowski, J. M.; Majorana, E.; Man, C. N.; Marchesoni, F.; Marion, F.; Martelli, F.; Masserot, A.; Massonnet, L.; Mataguez, S.; Menzinger, F.; Mazzoni, M.; Michel, C.; Milano, L.; Montorio, J. L.; Moreau, F.; Moreau, J.; Morgado, N.; Mornet, F.; Mours, B.; Mugnier, P.; Nenci, F.; Pacheco, J.; Pai, A.; Palomba, C.; Paoletti, F.; Paoli, A.; Paoli, L.; Pasqualetti, A.; Passaquieti, R.; Passuello, D.; Perciballi, M.; Peruzzi, S.; Perniola, B.; Pinard, L.; Poggiani, R.; Popolizio, P.; Porter, E.; Puccinelli, S.; Punturo, M.; Puppo, P.; Qipiani, K.; Ramonet, J.; Rapagnani, P.; Reita, V.; Remillieux, A.; Ricci, F.; Richard, F.; Roger, J. P.; Ruggi, P.; Russo, G.; Solimeno, S.; Stanga, R.; Taddei, R.; Teuler, J. M.; Tournefier, E.; Travasso, F.; Trinquet, H.; Turri, E.; Varvella, M.; Verkindt, D.; Vetrano, F.; Veziant, O.; Viceré, A.; Vilalte, S.; Y Vinet, J.; Vocca, H.; Yvert, M.; Zhang, Z.

    2003-09-01

    We report on the status of the VIRGO detector as of the beginning of 2003. In particular, we summarize the results obtained during the commissioning of the central portion of the detector, consisting of a power-recycled Michelson interferometer, and we outline the steps which will lead during 2003 and 2004 to the commissioning and operation of the full scale, 3 km long VIRGO detector.

  10. SalSA status

    International Nuclear Information System (INIS)

    I review the status of SalSA, a proposed antenna array in a large volume salt formation for detecting ultra-high energy neutrinos. We report on measurements taken in 2007 of attenuation lengths in the 125-900 MHz frequency range at the Cote Blanche salt mine near New Iberia, Louisiana, which is the most precise in situ measurement of attenuation lengths in salt to date. We comment on the impact of these measurements on the feasibility of SalSA.

  11. SalSA status

    Energy Technology Data Exchange (ETDEWEB)

    Connolly, Amy [Department of Physics and Astronomy, University College London, Gower Street, London WC1E 6BT (United Kingdom)], E-mail: amyc@hep.ucl.ac.uk

    2009-06-01

    I review the status of SalSA, a proposed antenna array in a large volume salt formation for detecting ultra-high energy neutrinos. We report on measurements taken in 2007 of attenuation lengths in the 125-900 MHz frequency range at the Cote Blanche salt mine near New Iberia, Louisiana, which is the most precise in situ measurement of attenuation lengths in salt to date. We comment on the impact of these measurements on the feasibility of SalSA.

  12. Present status and future development of the SAGA Light Source

    International Nuclear Information System (INIS)

    Present status and future development of the SAGA Light Source were described. The dedication of the SAGA Light Source was performed in February 2006, and has been open to industry, government, and academia users in the field of synchrotron radiation application. Also, new three beamlines will be installed in parallel with an expansion of the facility building. It is expected that the SAGA Light Source will serve an excellent function for advanced research and development in Kyushu. (author)

  13. Geomatics applied to building management

    International Nuclear Information System (INIS)

    An integrated information system at an educational facility which has the capacity to monitor relative data pertaining to the spatial characteristics of a building was demonstrated. The system was instrumental in optimizing building management by making use of geomatics technology. Geomatics establishes relations between geo-reference data (plans) and an actual data base. Such a system has the capability to integrate and assess all data relative to building management. The information allows building managers to rationalize exploitation costs and to coordinate energy use with the activities in the building

  14. Building a leadership brand.

    Science.gov (United States)

    Ulrich, Dave; Smallwood, Norm

    2007-01-01

    How do some firms produce a pipeline of consistently excellent managers? Instead of concentrating merely on strengthening the skills of individuals, these companies focus on building a broad organizational leadership capability. It's what Ulrich and Smallwood--cofounders of the RBL Group, a leadership development consultancy--call a leadership brand. Organizations with leadership brands take an "outside-in" approach to executive development. They begin with a clear statement of what they want to be known for by customers and then link it with a required set of management skills. The Lexus division of Toyota, for instance, translates its tagline--"The pursuit of perfection"--into an expectation that its leaders excel at managing quality processes. The slogan of Bon Secours Health System is "Good help to those in need." It demands that its managers balance business skills with compassion and caring. The outside-in approach helps firms build a reputation for high-quality leaders whom customers trust to deliver on the company's promises. In examining 150 companies with strong leadership capabilities, the authors found that the organizations follow five strategies. First, make sure managers master the basics of leadership--for example, setting strategy and grooming talent. Second, ensure that leaders internalize customers' high expectations. Third, incorporate customer feedback into evaluations of executives. Fourth, invest in programs that help managers hone the right skills, by tapping customers to participate in such programs. Finally, track the success of efforts to build leadership bench strength over the long-term. The result is outstanding management that persists even when individual executives leave. In fact, companies with the strongest leadership brands often become "leader feeders"--firms that regularly graduate leaders who go on to head other companies. PMID:17642128

  15. Sustainable Development and Green Buildings

    Directory of Open Access Journals (Sweden)

    Arijit Sinha

    2013-03-01

    Full Text Available Global sustainability goals have led to the development of the green building movement. The Green Building Program, stemming from the movement, has had unprecedented success as it provides a quantifiable metric to people’s efforts towards sustainable development. Sustainable development and green buildings are often used interchangeably. Although, sustainable development and green buildings are related, they are not the same. This paper provides an overview of how green building relates to sustainable development practices. Sustainability also governs decisions concerning building materials. A comprehensive explanation of what constitutes a green building material is discussed and how renewable material like wood fare in the deciding criteria. There are many green building rating systems in place. United States Green Building Council administered Leadership in Energy and Environment Design (LEED is the global market leader in the rating systems. LEED is a commendable and grand effort in moving towards sustainable development by converting the built environment green. However, it does have certain pitfalls and challenges. Some of these challenges are with respect to policies on material selection and performance monitoring. The materials used in a project are considered at a common starting point and no consideration is given to the life cycle performance of the material. Statements concerning sustainability require validation, and Life Cycle Analysis (LCA is a tool that can provide such validity. This paper presents how beneficial it can be, when included, in the bigger scheme of green building rating systems and introduces an integrated design concept for green buildings.

  16. Tropical Zero Energy Office Building

    DEFF Research Database (Denmark)

    Reimann, Gregers Peter; Kristensen, Poul Erik

    2006-01-01

    by daylight, supplemented by electric lighting during very dark and overcast periods. Extensive active energy efficiency measures are implemented in the building in order to reduce the need for electricity to an absolute minimum, without compromising the request for comfortable temperatures and adequate......The new headquarter for Pusat Tenaga Malaysia is designed to be a Zero Emission Office Building (ZEO). A full range of passive and active energy efficiency measures are implemented such that the building will need no more electricity than what can be produced via its own Building Integrated PV...... system. The overall objective of the project is to achieve zero energy consumption at lowest possible initial investments. The ZEO Building shows implementation of integrated design concepts, where active and passive energy systems are interwoven into the building itself, and where several building...

  17. Nuclear building blocks

    International Nuclear Information System (INIS)

    The Candu 300 is the latest and smallest version of the CANDU pressurized heavy water reactor. It is designed for modular construction which, it is hoped, will shorten the construction schedule, take advantage of factory construction, improve quality (because central work locations and better conditions can be used) and provide flexibility of supply. The basic CANDU nuclear steam supply system is described generally and then the station and building layout, modular construction sequence (using a very heavy lift mobile crane), the process system modules and major nuclear equipment modules, are described in more detail. The advantages of modularisation are explained and plans for future modular reactors are mentioned. (U.K.)

  18. Mould growth in buildings

    OpenAIRE

    Holme, Jonas

    2010-01-01

    Many studies around the world have reported that moisture-related problems in buildings (i.e., dampness) increase the risk of health effects such as respiratory symptoms, asthma and allergy in both adults and children. However, there is only limited knowledge about which agents in indoor air or dust cause the reported health effects. Biological pollutants such as moulds is one of the explanations that has been suggested. The principal objective of this PhD study has been to increase the knowl...

  19. Building Web Reputation Systems

    CERN Document Server

    Farmer, Randy

    2010-01-01

    What do Amazon's product reviews, eBay's feedback score system, Slashdot's Karma System, and Xbox Live's Achievements have in common? They're all examples of successful reputation systems that enable consumer websites to manage and present user contributions most effectively. This book shows you how to design and develop reputation systems for your own sites or web applications, written by experts who have designed web communities for Yahoo! and other prominent sites. Building Web Reputation Systems helps you ask the hard questions about these underlying mechanisms, and why they're critical

  20. Tall Buildings and Urban Habitat of the 21st Century: A Global Perspective

    Directory of Open Access Journals (Sweden)

    Mir M. Ali

    2012-09-01

    Full Text Available The tall building is the most dominating symbol of the cities and a human-made marvel that defies gravity by reaching to the clouds. It embodies unrelenting human aspirations to build even higher. It conjures a number of valid questions in our minds. The foremost and fundamental question that is often asked: Why tall buildings? This review paper seeks to answer the question by laying out arguments against and for tall buildings. Then, it provides a brief account of the historic and recent developments of tall buildings including their status during the current economic recession. The paper argues that as cities continue to expand horizontally, to safeguard against their reaching an eventual breaking point, the tall building as a building type is a possible solution by way of conquering vertical space through agglomeration and densification. Case studies of some recently built tall buildings are discussed to illustrate the nature of tall building development in their respective cities. The paper attempts to dispel any discernment about tall buildings as mere pieces of art and architecture by emphasizing their truly speculative, technological, sustainable, and evolving nature. It concludes by projecting a vision of tall buildings and their integration into the cities of the 21st century.

  1. Building energy governance in Shanghai

    Science.gov (United States)

    Kung, YiHsiu Michelle

    With Asia's surging economies and urbanization, the region is adding to its built environment at an unprecedented rate, especially those population centers in China and India. With numerous existing buildings, plus a new building boom, construction in these major Asian cities has caused momentous sustainability challenges. This dissertation focuses on China's leading city, Shanghai, to explore and assess its existing commercial building energy policies and practices. Research estimates that Shanghai's commercial buildings might become a key challenge with regard to energy use and CO2 emissions as compared to other major Asian cities. Relevant building energy policy instruments at national and local levels for commercial buildings are reviewed. In addition, two benchmarks are established to further assess building energy policies in Shanghai. The first benchmark is based on the synthesis of relevant criteria and policy instruments as recommended by professional organizations, while the second practical benchmark is drawn from an analysis of three global cities: New York, London and Tokyo. Moreover, two large-scale commercial building sites - Shanghai IKEA and Plaza 66 - are selected for investigation and assessment of their efforts on building energy saving measures. Detailed building energy savings, CO2 reductions, and management cost reductions based on data availability and calculations are presented with the co-benefits approach. The research additionally analyzes different interventions and factors that facilitate or constrain the implementation process of building energy saving measures in each case. Furthermore, a multi-scale analytical framework is employed to investigate relevant stakeholders that shape Shanghai's commercial building energy governance. Research findings and policy recommendations are offered at the close of this dissertation. Findings and policy recommendations are intended to facilitate commercial building energy governance in Shanghai and

  2. Tesauro ISOC de Topónimos 2004 (Edición abreviada)

    OpenAIRE

    Maldonado Martínez, Ángeles; Rodríguez Yunta, Luis

    2004-01-01

    [EN] This abridged edition of the thesaurus has 14,382 place names, of which 12,288 are primary and 2,094 equivalent. 196 countries are represented at the next level of development: • Spain with autonomous communities, provinces and municipalities. • European Union countries (before enlargement of 2004) to two administrative levels of territorial organization except Denmark, Finland, Netherlands and Sweden which has been considered only one level. In all countries have been included the...

  3. An Analysis of Statewide Adoption Rates of Building Energy Code by Local Jurisdictions

    Energy Technology Data Exchange (ETDEWEB)

    Cort, Katherine A.; Butner, Ryan S.

    2012-12-31

    The purpose of this study is to generally inform the U.S. Department of Energy’s Building Energy Codes Program of the local, effective energy code adoption rate for a sample set of 21 states, some which have adopted statewide codes and some that have not. Information related to the residential energy code adoption process and status at the local jurisdiction was examined for each of the states. Energy code status information was gathered for approximately 2,800 jurisdictions, which effectively covered approximately 80 percent of the new residential building construction in the 21 states included in the study.

  4. Models test on dynamic structure-structure interaction of nuclear power plant buildings

    International Nuclear Information System (INIS)

    A reactor building of an NPP (nuclear power plant) is generally constructed closely adjacent to a turbine building and other buildings such as the auxiliary building, and in increasing numbers of NPPs, multiple plants are being planned and constructed closely on a single site. In these situations, adjacent buildings are considered to influence each other through the soil during earthquakes and to exhibit dynamic behaviour different from that of separate buildings, because those buildings in NPP are generally heavy and massive. The dynamic interaction between buildings during earthquake through the soil is termed here as 'dynamic cross interaction (DCI)'. In order to comprehend DCI appropriately, forced vibration tests and earthquake observation are needed using closely constructed building models. Standing on this background, Nuclear Power Engineering Corporation (NUPEC) had planned the project to investigate the DCI effect in 1993 after the preceding SSI (soil-structure interaction) investigation project, 'model tests on embedment effect of reactor building'. The project consists of field and laboratory tests. The field test is being carried out using three different building construction conditions, e.g. a single reactor building to be used for the comparison purposes as for a reference, two same reactor buildings used to evaluate pure DCI effects, and two different buildings, reactor and turbine building models to evaluate DCI effects under the actual plant conditions. Forced vibration tests and earthquake observations are planned in the field test. The laboratory test is planned to evaluate basic characteristics of the DCI effects using simple soil model made of silicon rubber and structure models made of aluminum. In this test, forced vibration tests and shaking table tests are planned. The project was started in April 1994 and will be completed in March 2002. This paper describes an outline and the summary of the current status of this project. (orig.)

  5. Irregular Shaped Building Design Optimization with Building Information Modelling

    Directory of Open Access Journals (Sweden)

    Lee Xia Sheng

    2016-01-01

    Full Text Available This research is to recognise the function of Building Information Modelling (BIM in design optimization for irregular shaped buildings. The study focuses on a conceptual irregular shaped “twisted” building design similar to some existing sculpture-like architectures. Form and function are the two most important aspects of new buildings, which are becoming more sophisticated as parts of equally sophisticated “systems” that we are living in. Nowadays, it is common to have irregular shaped or sculpture-like buildings which are very different when compared to regular buildings. Construction industry stakeholders are facing stiff challenges in many aspects such as buildability, cost effectiveness, delivery time and facility management when dealing with irregular shaped building projects. Building Information Modelling (BIM is being utilized to enable architects, engineers and constructors to gain improved visualization for irregular shaped buildings; this has a purpose of identifying critical issues before initiating physical construction work. In this study, three variations of design options differing in rotating angle: 30 degrees, 60 degrees and 90 degrees are created to conduct quantifiable comparisons. Discussions are focused on three major aspects including structural planning, usable building space, and structural constructability. This research concludes that Building Information Modelling is instrumental in facilitating design optimization for irregular shaped building. In the process of comparing different design variations, instead of just giving “yes or no” type of response, stakeholders can now easily visualize, evaluate and decide to achieve the right balance based on their own criteria. Therefore, construction project stakeholders are empowered with superior evaluation and decision making capability.

  6. Towards more Manageable Coastal Building; Initial Coastal Building Construction Guidelines

    OpenAIRE

    Roslan Talib; Mohd Z. Sulieman

    2011-01-01

    Problem statement: As we may not be aware that the coastal construction is different from inland construction. Building in a coastal environment is different from building in an inland area. In general, buildings in coastal areas must be designed and built to withstand higher loads due to its more extreme conditions. Nowadays, the issue of global warming, uncertainty of global weather and the climate change effect indirectly creating the coastal area with much more expose to extreme condition...

  7. Parameters of Upgrading Existing Building into a Green Building

    OpenAIRE

    Mrs. Rupali Kapure; Dr.R.K.Jain

    2014-01-01

    Before turning to specific programs for upgrading buildings, it’s important to understand the market dynamics of greening existing buildings. From a macroeconomic perspective, energy efficiency upgrades represent the most cost-effective way to meet growing energy demands. From a microeconomic perspective, recent studies have shown that energy-efficient and certified green buildings merit higher market values, greater rents, and higher occupancies. From a corporate sustainabili...

  8. Pharmacotherapy for Status Epilepticus.

    Science.gov (United States)

    Trinka, Eugen; Höfler, Julia; Leitinger, Markus; Brigo, Francesco

    2015-09-01

    Status epilepticus (SE) represents the most severe form of epilepsy. It is one of the most common neurologic emergencies, with an incidence of up to 61 per 100,000 per year and an estimated mortality of 20 %. Clinically, tonic-clonic convulsive SE is divided into four subsequent stages: early, established, refractory, and super-refractory. Pharmacotherapy of status epilepticus, especially of its later stages, represents an "evidence-free zone," due to a lack of high-quality, controlled trials to inform clinical decisions. This comprehensive narrative review focuses on the pharmacotherapy of SE, presented according to the four-staged approach outlined above, and providing pharmacological properties and efficacy/safety data for each antiepileptic drug according to the strength of scientific evidence from the available literature. Data sources included MEDLINE and back-tracking of references in pertinent studies. Intravenous lorazepam or intramuscular midazolam effectively control early SE in approximately 63-73 % of patients. Despite a suboptimal safety profile, intravenous phenytoin or phenobarbital are widely used treatments for established SE; alternatives include valproate, levetiracetam, and lacosamide. Anesthetics are widely used in refractory and super-refractory SE, despite the current lack of trials in this field. Data on alternative treatments in the later stages are limited. Valproate and levetiracetam represent safe and effective alternatives to phenobarbital and phenytoin for treatment of established SE persisting despite first-line treatment with benzodiazepines. To date there are no class I data to support recommendations for most antiepileptic drugs for established, refractory, and super-refractory SE. Limiting the methodologic heterogeneity across studies is required and high-class randomized, controlled trials to inform clinicians about the best treatment in established and refractory status are needed. PMID:26310189

  9. Model Validation Status Review

    Energy Technology Data Exchange (ETDEWEB)

    E.L. Hardin

    2001-11-28

    The primary objective for the Model Validation Status Review was to perform a one-time evaluation of model validation associated with the analysis/model reports (AMRs) containing model input to total-system performance assessment (TSPA) for the Yucca Mountain site recommendation (SR). This review was performed in response to Corrective Action Request BSC-01-C-01 (Clark 2001, Krisha 2001) pursuant to Quality Assurance review findings of an adverse trend in model validation deficiency. The review findings in this report provide the following information which defines the extent of model validation deficiency and the corrective action needed: (1) AMRs that contain or support models are identified, and conversely, for each model the supporting documentation is identified. (2) The use for each model is determined based on whether the output is used directly for TSPA-SR, or for screening (exclusion) of features, events, and processes (FEPs), and the nature of the model output. (3) Two approaches are used to evaluate the extent to which the validation for each model is compliant with AP-3.10Q (Analyses and Models). The approaches differ in regard to whether model validation is achieved within individual AMRs as originally intended, or whether model validation could be readily achieved by incorporating information from other sources. (4) Recommendations are presented for changes to the AMRs, and additional model development activities or data collection, that will remedy model validation review findings, in support of licensing activities. The Model Validation Status Review emphasized those AMRs that support TSPA-SR (CRWMS M&O 2000bl and 2000bm). A series of workshops and teleconferences was held to discuss and integrate the review findings. The review encompassed 125 AMRs (Table 1) plus certain other supporting documents and data needed to assess model validity. The AMRs were grouped in 21 model areas representing the modeling of processes affecting the natural and

  10. 1998 status report

    International Nuclear Information System (INIS)

    Since its creation in 1945, the activities of Cea have been centered on the study and development of the pacific use of nuclear energy and on assuring the credibility of nuclear deterrent. This status report presents the research programs led by Cea in 1998. The main topics are: the designing of reactor cores, fuel cycle, nuclear safety, radiation protection, the activities for defense, high technologies for industry, biology and fundamental sciences. The quality of research work is assured by an independent and regular assessment of the scientific activities. (A.C.)

  11. Folate status and health

    DEFF Research Database (Denmark)

    Obeid, Rima; Oexle, Konrad; Rißmann, Anke; Pietrzik, Klaus; Koletzko, Berthold

    2015-01-01

    worldwide by applying fortification with folic acid. Periconceptional supplementation of folic acid also reduces the risk of congenital heart diseases, preterm birth, low birth weight, and health problems associated with child mortality and morbidity. All European governments failed to issue folic acid...... health centers for prenatal care and fortification with folic acid in Europe are urgently needed. Only such an action will sufficiently improve folate status, prevent at least 50% of the NTD cases, reduce child mortality and morbidity, and alleviate other health problems associated with low folate such...

  12. Status epilepticus in scleromyxedema

    Institute of Scientific and Technical Information of China (English)

    Soifa Markoula; Soifa Zouroudi; Soitrios Giannopoulos; Kimon Tsoukanelis; Ananstasia Zikou; Athanassios P Kyritsis

    2016-01-01

    Scleromyxedema is a rare dermatologic disorder, characterized by erythematous or yelowish lichenoid waxy papules. Neurological manifestations are rare but wel-recognized. A 51-year-old woman, diagnosed with scleromyxedema, was admitted to the hospital with status epilepticus, caused by brain lesions, as disclosed in a brain magnetic resonance imaging (MRI). The patient was treated with anticonvulsants and corticosteroids and gradualy recovered fuly. A complete remission of the lesions was shown in a folow-up brain MRI. In cases with scleromyxedema and the presence of neurological manifestations, we need to pay attention to central nervous system involvement, especialy when combined with brain MRI lesions, and treat the patient appropriately.

  13. Model Validation Status Review

    International Nuclear Information System (INIS)

    The primary objective for the Model Validation Status Review was to perform a one-time evaluation of model validation associated with the analysis/model reports (AMRs) containing model input to total-system performance assessment (TSPA) for the Yucca Mountain site recommendation (SR). This review was performed in response to Corrective Action Request BSC-01-C-01 (Clark 2001, Krisha 2001) pursuant to Quality Assurance review findings of an adverse trend in model validation deficiency. The review findings in this report provide the following information which defines the extent of model validation deficiency and the corrective action needed: (1) AMRs that contain or support models are identified, and conversely, for each model the supporting documentation is identified. (2) The use for each model is determined based on whether the output is used directly for TSPA-SR, or for screening (exclusion) of features, events, and processes (FEPs), and the nature of the model output. (3) Two approaches are used to evaluate the extent to which the validation for each model is compliant with AP-3.10Q (Analyses and Models). The approaches differ in regard to whether model validation is achieved within individual AMRs as originally intended, or whether model validation could be readily achieved by incorporating information from other sources. (4) Recommendations are presented for changes to the AMRs, and additional model development activities or data collection, that will remedy model validation review findings, in support of licensing activities. The Model Validation Status Review emphasized those AMRs that support TSPA-SR (CRWMS M and O 2000bl and 2000bm). A series of workshops and teleconferences was held to discuss and integrate the review findings. The review encompassed 125 AMRs (Table 1) plus certain other supporting documents and data needed to assess model validity. The AMRs were grouped in 21 model areas representing the modeling of processes affecting the natural and

  14. Status of APE projects

    International Nuclear Information System (INIS)

    This talk is divided in two parts. In the first part, we will summarize the status of the APEmille project that will be completed by the end of the year. We will then devote the rest of the talk to the description of a new project for a multi-TeraFlop machine, apeNEXT. The interested reader will find a much more detailed discussion of all the items touched upon here in the full proposal of the project that will shortly appear on hep-lat

  15. NESTOR: a status report

    International Nuclear Information System (INIS)

    NESTOR is the detector for the underwater neutrino astrophysics laboratory to be located in the international waters off the southwest of Greece. The first phase of this experiment is the construction and deployment of one hexagonal tower, with effective area for TeV neutrinos of 20 000 m2, consisting of 168 optical modules. The tower will be deployed in a single operation in '97. Over the past few years detailed studies of the site have been carried out while many of the major constituents of the detector have been under test. The current status of the preparation of the experiment will be presented. (orig.)

  16. Status of safeguards instrumentation

    International Nuclear Information System (INIS)

    The International Atomic Energy Agency is performing safeguards at some nuclear power reactors, 50 bulk processing facilities, and 170 research facilities. Its verification activities require the use of instruments to measure nuclear materials and of surveillance instruments to maintain continuity of knowledge of the locations of nuclear materials. Instruments that are in use and under development to measure weight, volume, concentration, and isotopic composition of nuclear materials, and the major surveillance instruments, are described in connection with their uses at representative nuclear facilities. The current status of safeguards instrumentation and the needs for future development are discussed

  17. Reactor gamma spectrometry: status

    International Nuclear Information System (INIS)

    Current work is described for Compton Recoil Gamma-Ray Spectrometry including developments in experimental technique as well as recent reactor spectrometry measurements. The current status of the method is described concerning gamma spectromoetry probe design and response characteristics. Emphasis is given to gamma spectrometry work in US LWR and BR programs. Gamma spectrometry in BR environments are outlined by focussing on start-up plans for the Fast Test Reactor (FTR). Gamma spectrometry results are presented for a LWR pressure vessel mockup in the Poolside Critical Assembly (PCA) at Oak Ridge National Laboratory

  18. Teleradiology - current status

    International Nuclear Information System (INIS)

    Tele-radiology is a term becoming increasingly popular in the medical literature. Nevertheless, terminological definitions in this particular field are still rather vague. The scope of applications extend from simple image presenting via analogue telephone lines to transmission of 3-D medical images through a satellite. It is a matter of standards highly differing in terms of data transmission rates, safety, technical demands on the systems and the like. In this article new information technologies, technical aspects, as well as some major applications of tele-radiology are discussed. The current status of tele-medicine/tele-radiology in this country is likewise briefly outlined

  19. NESTOR: A status report

    CERN Document Server

    Anassontzis, E G; Barone, M; Foudas, C; Grammatikakis, G; Katsanevas, S; Kourkoumelis, C; Manousakis-Katsikakis, A; Resvanis, L K; Siotis, I; Sotiriou, S A; Voulgaris, G; Minkowski, P; Grieder, P K F; Ball, A E; Bottai, S; Cartacci, A M; Monteleoni, B; Naumov, Vadim A; Trasatti, L; Fahrun, E; Keusen, U; Koske, P; Rathlev, J; Schmidt, N P; Voight, G; Bezrukov, Leonid B; Butkevich, A V; Dedenko, L G; Karaevsky, S K; Mironovich, A A; Zakharov, L M; Zheleznykh, I M; Zhukov, V A; Demidova, T A; Deineko, A O; Eremeev, A P; Paka, V T; Permyakov, A A; Platonov, M N; Rukol, V Kh; Sheremet, N A; Surin, N M; Albul, V I; Ledenev, V V

    2000-01-01

    NESTOR is an underwater neutrino astrophysics laboratory to be located in the international waters of the southwest of Greece. The first phase of this experiment is the construction and deployment of one hexagonal tower consisting of 168 optical modules, with effective are of 20000m2 for E ⩾ TeV neutrinos. Over the past few years detailed studies of the site have been carried out while many tests have been performed. The current status of the preparation of the experiment and the future plans will be presented.

  20. Energy Efficiency, Building Productivity and the Commercial Buildings Market

    Energy Technology Data Exchange (ETDEWEB)

    Jones, D.W.

    2002-05-16

    The energy-efficiency gap literature suggests that building buyers are often short-sighted in their failure to apply life-cycle costing principles to energy efficient building technologies, with the result that under investment in these advanced technology occurs. This study examines the reasons this behavior may occur, by analyzing the pressures that market forces place on purchasers of buildings. Our basic conclusion is that the fundamental manner in which the buildings sector does business creates pressures to reduce initial capital outlays and to hedge against a variety of risks, including the ability of building owners to capture benefits from energy efficiency. Starting from the position that building buyers' willingness to pay drives choices over building attributes, we examine basic market principles, the structure of the buildings market, including the role of lenders, and policies that promote penetration of energy efficient technologies. We conclude that greater attention to buyers, and to the incentives and constraints they face, would promote a better understanding of building investment choices and contribute to better policies to promote the penetration of these technologies into markets.

  1. Parameters of Upgrading Existing Building into a Green Building

    Directory of Open Access Journals (Sweden)

    Mrs. Rupali Kapure

    2014-02-01

    Full Text Available Before turning to specific programs for upgrading buildings, it’s important to understand the market dynamics of greening existing buildings. From a macroeconomic perspective, energy efficiency upgrades represent the most cost-effective way to meet growing energy demands. From a microeconomic perspective, recent studies have shown that energy-efficient and certified green buildings merit higher market values, greater rents, and higher occupancies. From a corporate sustainability viewpoint, greening existing buildings is a direct way to reduce a company’s carbon footprint. As a result, corporate real estate managers in the United States have begun to decide in favour of greening both owned and leased buildings, seeing many economic benefits from this switch. Green buildings offer many marketing benefits for building owners and tenants, including opportunities for creating new green “brands” and also “future-proofing” their real estate against both future energy price increases and also value erosion as the trend toward green buildings continues to grow. Marketing benefits will vary by geographic location, building and tenant type, and other factors, but they are present in all privately owned real estate.

  2. Building America Case Study: Solar Water Heating in Multifamily Buildings

    Energy Technology Data Exchange (ETDEWEB)

    R. Aldrich and J. Williamson

    2016-05-01

    Solar domestic hot water (SDHW) systems have been installed on buildings for decades, but because of relatively high costs they have not achieved significant market penetration in most of the country. As more buildings move towards zero net energy consumption, however, many designers and developers are looking more closely at SDHW. In multifamily buildings especially, SDHW may be more practical for several reasons: (1) When designing for zero net energy consumption, solar water heating may be part of the lowest cost approach to meet water heating loads. (2.) Because of better scale, SDHW systems in multifamily buildings cost significantly less per dwelling than in single-family homes. (3) Many low-load buildings are moving away from fossil fuels entirely. SDHW savings are substantially greater when displacing electric resistance water heating. (4) In addition to federal tax incentives, some states have substantial financial incentives that dramatically reduce the costs (or increase the benefits) of SDHW systems in multifamily buildings. With support form the U.S. DOE Building America program, the Consortium for Advanced Residential Buildings (CARB) worked with a developer in western Massachusetts to evaluate a SDHW system on a 12-unit apartment building. Olive Street Development completed construction in spring of 2014, and CARB has been monitoring performance of the water heating systems since May 2014.

  3. Inertial fusion program-present status

    International Nuclear Information System (INIS)

    The present status of the inertial fusion program is reviewed. The program has two major applications, one to military areas, the other to longterm energy needs. The near-term program is described by a 5-year program plan that coordinates research and culminates in a 1987 decision. The near-term program strategy is to build and operate the three new large facilities, ANTARES, NOVA, and PBFA II in order to maximize the physics data base needed to evaluate the drivertarget requirements for ignition and higher gain. Low-cost driver technology will also play an important role in the 1987 program decision. Depending on the outcome of this decision, there is a succession of archetypical facilities and associated systems studies necessary to achieve goals for long-term energy needs through inertial fusion. These are briefly discussed

  4. Mothers’ Employment, Marital Status and Educational Level on Students’ Academic Achievement in Business Studies

    OpenAIRE

    Subuola Catherine Abosede; Olugbenga Adeyanju Akintola

    2016-01-01

    The mother’s personality is a build-up of demographic factors among which employment, marital status and educational level are prominent in shaping child’s abilities and aspirations. This study therefore, determines the influence of mothers’ employment, marital status and educational level on students’ academic achievement in Business studies. Ex-post facto survey design and stratified random sampling technique were adopted for the study.Structured Questionnaire (MEMSEL Scale, r= ...

  5. TOO COOL FOR SCHOOL? VIOLENCE, PEER STATUS, AND HIGH SCHOOL DROPOUT*

    OpenAIRE

    Staff, Jeremy; Kreager, Derek A.

    2008-01-01

    Research shows that peer status in adolescence is positively associated with school achievement and adjustment. However, subculture theories of juvenile delinquency and school-based ethnographies suggest that (1) disadvantaged boys are often able to gain some forms of peer status through violence and (2) membership in violent groups undermines educational attainment. Building on these ideas, we use peer network data from the National Longitudinal Study of Adolescent Health (Add Health) to exa...

  6. Guidelines for Building Science Education

    Energy Technology Data Exchange (ETDEWEB)

    Metzger, Cheryn E.; Rashkin, Samuel; Huelman, Pat

    2015-03-11

    The U.S. Department of Energy’s (DOE) residential research and demonstration program, Building America, has triumphed through 20 years of innovation. Partnering with researchers, builders, remodelers, and manufacturers to develop innovative processes like advanced framing and ventilation standards, Building America has proven an energy efficient design can be more cost effective, healthy, and durable than a standard house. As Building America partners continue to achieve their stretch goals, they have found that the barrier to true market transformation for high performance homes is the limited knowledge-base of the professionals working in the building industry. With dozens of professionals taking part in the design and execution of building and selling homes, each person should have basic building science knowledge relevant to their role, and an understanding of how various home components interface with each other. Instead, our industry typically experiences a fragmented approach to home building and design. After obtaining important input from stakeholders at the Building Science Education Kick-Off Meeting, DOE created a building science education strategy addressing education issues preventing the widespread adoption of high performance homes. This strategy targets the next generation and provides valuable guidance for the current workforce. The initiative includes: • Race to Zero Student Design Competition: Engages universities and provides students who will be the next generation of architects, engineers, construction managers and entrepreneurs with the necessary skills and experience they need to begin careers in clean energy and generate creative solutions to real world problems. • Building Science to Sales Translator: Simplifies building science into compelling sales language and tools to sell high performance homes to their customers. • Building Science Education Guidance: Brings together industry and academia to solve problems related to

  7. Muon Collider design status

    OpenAIRE

    Alexahin, Y.

    2012-01-01

    Muon Collider (MC) - proposed by G. I. Budker and A. N. Skrinsky a few decades ago - is now considered as the most exciting option for the energy frontier machine in the post-LHC era. A national Muon Accelerator Program (MAP) is being formed in the USA with the ultimate goal of building a MC at the Fermilab site with c.o.m. energy in the range 1.5-3 TeV and luminosity of ~1-5 \\times 10^{34} cm^{-2}s^{-1}1. As the first step on the way to MC it envisages construction of a Neutrino Factory (NF)...

  8. ANTARES Status Report

    CERN Document Server

    Montaruli, T

    2003-01-01

    The ANTARES Collaboration is building a neutrino telescope 2400 m below the Mediterranean sea close to the Southern French coast. The site is already linked to the shore station by a 40 km-long electro-optical cable (EOC) which transmits power and data. A prototype line and an instrumentation line for monitoring environmental parameters have been successfully deployed and connected to the EOC via the junction box, using the IFREMER manned submarine. The Collaboration, after years of dedicated R&D and deployments of prototype lines, is now ready to deploy the detector starting in spring 2004.

  9. Radiation exposure from building materials

    International Nuclear Information System (INIS)

    A survey procedure was developed to find buildings in which the radiation exposure from gamma rays is relatively high. For modern structures NaI(Tl) survey meters are used to identify building materials with higher radionuclide content. Samples of these materials are analyzed by gamma-ray spectroscopy for 226Ra daughters, 232Th daughters, and 40K. The exposure rate in a building is computed from these concentrations on the basis of the geometrical configuration of building materials, acting both as radiation sources and as a shield against terrestrial radiation, and also on the basis of the outside radiation exposure rate at the building site. The procedure may also be applied to surveys of building material constituents and to materials in place in older structures. A calculational model was developed to predict radiation exposure rates within the houses

  10. Status of thermal imaging technology as applied to conservation-update 1

    Energy Technology Data Exchange (ETDEWEB)

    Snow, F.J.; Wood, J.T.; Barthle, R.C.

    1980-07-01

    This document updates the 1978 report on the status of thermal imaging technology as applied to energy conservation in buildings. Thermal imaging technology is discussed in terms of airborne surveys, ground survey programs, and application needs such as standards development and lower cost equipment. Information on the various thermal imaging devices was obtained from manufacturer's standard product literature. Listings are provided of infrared projects of the DOE building diagnostics program, of aerial thermographic firms, and of aerial survey programs. (LCL)

  11. Renovating the Main Building

    CERN Multimedia

    CERN Bulletin

    2010-01-01

    CERN's "Main Building" is exactly that. The Organization's central hub, with hundreds of staff and visitors passing through its doors every day, will soon be getting a well-earned facelift. Refurbishment work will proceed in phases, starting with the Salle des Pas Perdus, the concourse between the Council Chamber and the Main Auditorium. By the end of August, informal seating areas will be installed, electronic display panels will provide practical information and improved sound insulation will enhance conditions in the auditoria and surrounding meeting rooms.   In light green the area that will undergo the facelift. Work will start in July. The ground floor is home to the entrance to Restaurant No. 1, the bank, the post office, the travel agent, the Users Office, the Staff Association, the notice boards etc. Step up to the first floor to access CERN's largest lecture theatre, the Council Chamber and its "Pas Perdus" lobby. Everyone who works at or visits CERN i...

  12. Photovoltaic building blocks

    DEFF Research Database (Denmark)

    Hanberg, Peter Jesper; Jørgensen, Anders Michael

    2014-01-01

    efficiency of about 15% for commercial Silicon solar cells there is still much to gain. DTU Danchip provides research facilities, equipment and expertise for the building blocks that comprises fabricating the efficient solar cell. In order to get more of the sun light into the device we provide thin film...... coating tools to depositand develop anti-reflection filters by means of sputtering or e-beam evaporation. To reduce the area taken up by metallic contacts transparent conducting oxides like Aluminium doped ZincOxide (AZO) and Indium Tin Oxide (ITO) can be deposited. We also support research...... and development of new 2D materials like graphene that is a promising candidate for cheap highly transparent contacts. Another way to increase efficiency is to structure the active layers indevice so that more light is absorbed. This can be done in one of our advanced dry etching machines either mask-less to form...

  13. Building Land Information Policies

    DEFF Research Database (Denmark)

    Enemark, Stig

    2004-01-01

    The paper presents a conceptual understanding in the areas of Cadastre, Land Administration, and Land Management as a basis for building adequate land information policies. To develop this understanding the paper looks at each area as a system or an infrastructure designed for handling specific...... measurement science, spatial information, management, and land management. (2) To establish national professional associations which accommodate a modern interdisciplinary profile. (3) To assess the capacity needs in land administration and to develop the capacity needed at societal, institutional and...... personal level.    (4) To establish appropriate institutional and organisational infrastructures to manage the integration of topographic mapping and cadastral information into a coherent land administration system for sustainable development. The paper aims to establish the basic understanding for dealing...

  14. Zinc status of vegetarians.

    Science.gov (United States)

    Freeland-Graves, J H; Bodzy, P W; Eppright, M A

    1980-12-01

    The zinc status of seventy-nine vegetarians and forty-one non-vegetarians was investigated. The subjects provided 24-hr. dietary recalls and donated samples of blood, hair, and saliva that were subsequently analyzed for zinc content. Avoidance of animal products in the diet was associated with decreased intakes of energy, protein, fat, calcium, and zinc and increased consumption of crude fiber, potassium, vitamin A, and ascorbic acid. The low dietary intake of zinc by vegetarian women was believed to result from liberal use of foods low in zinc such as fruits and vegetables, whereas vegetarian men primarily consumed zinc-rich food such as legumes and cheeses Lacto-ovo-vegetarians consumed twice the amount of crude fiber consumed by non-vegetarians and vegans four times as much. The zinc content of salivary sediment was significantly lower in vegetarians than in non-vegetarians; vegans had the lowest mean level. The observed decrease in salivary zinc was inversely proportional to the amount of crude fiber in the diet. Zinc levels in the hair of vegetarians were significantly lower than those in the hair of non-vegetarians, while serum levels were also lower, but not significantly so. The increased crude fiber intake of vegetarians coupled with the decreased levels of zinc found in saliva and hair seem to indicate that some vegetarians, particularly women, have less than satisfactory zinc status. PMID:7440860

  15. Building better boards.

    Science.gov (United States)

    Nadler, David A

    2004-05-01

    Companies facing new requirements for governance are scrambling to buttress financial-reporting systems, overhaul board structures--whatever it takes to comply. But there are limits to how much good governance can be imposed from the outside. Boards know what they ought to be: seats of challenge and inquiry that add value without meddling and make CEOs more effective but not all-powerful. A board can reach that goal only if it functions as a high-performance team, one that is competent, coordinated, collegial, and focused on an unambiguous goal. Such entities don't just evolve; they must be constructed to an exacting blueprint--what the author calls board building. In this article, Nadler offers an agenda and a set of tools that boards can use to define and achieve their objectives. It's important for a board to conduct regular self-assessments and to pay attention to the results of those analyses. As a first step, the directors and the CEO should agree on which of the following common board models best fits the company: passive, certifying, engaged, intervening, or operating. The directors and the CEO should then analyze which business tasks are most important and allot sufficient time and resources to them. Next, the board should take inventory of each director's strengths to ensure that the group as a whole possesses the skills necessary to do its work. Directors must exert more influence over meeting agendas and make sure they have the right information at the right time and in the right format to perform their duties. Finally, the board needs to foster an engaged culture characterized by candor and a willingness to challenge. An ambitious board-building process, devised and endorsed both by directors and by management, can potentially turn a good board into a great one. PMID:15146740

  16. Building Evacuation with Mobile Devices

    OpenAIRE

    Merkel, Sabrina

    2014-01-01

    The rapidly growing world population and increasingly dense settlements demand ever-larger and more complex buildings from today's engineers. In comparison to this technological progress, a building's equipment for emergency evacuation has been hardly developed further. This work presents a concept for a building evacuation system based on mobile devices. Furthermore, various algorithms for route planning with mobile devices and for indoor localization of mobile devices are addressed.

  17. The Netherlands' School Building Prize

    OpenAIRE

    OECD

    1999-01-01

    The School Building Prize has been awarded every two years since 1992 to Dutch school boards that have proved able to embrace new directions in school building design while keeping within their available budget. The Prize, which has drawn acclaim for the development of high quality educational architecture in the Netherlands, provides publicity for successful projects so that other schools can benefit from the designs and information. The 1998 School Building Prize was awarded to the British ...

  18. Mould growth on building materials

    DEFF Research Database (Denmark)

    Fog Nielsen, K.

    Mould growth in buildings is associated with adverse health effects among the occupants of the building. However actual growth only occurs in damp and water-damaged materials, and is an increasing problem in Denmark, due to less robust constructions, inadequate maintenance, and too little...... ventilation. This project was started to determine if mycotoxins are produced in damp and water-damaged buildings as well investigating the influence of environmental conditions (humidity and temperature) on the production of fungal growth and secondary metabolism....

  19. Sustainability in Energy and Buildings

    OpenAIRE

    Kinnane, Oliver; Basu, Biswajit

    2014-01-01

    PUBLISHED Cardiff This paper presents a new methodology for characterising the energy performance of buildings suitable for city-scale, top-down energy modelling. Building properties that have the greatest impact on simulated energy performance were identified via a review of sensitivity analysis studies. The methodology greatly simplifies the description of a building to decrease labour and simulation processing overheads. The methodology will be used in the EU FP7 INDICATE project whi...

  20. Energy-efficient timber buildings

    OpenAIRE

    Zbašnik-Senegačnik, Martina; Kitek Kuzman, Manja

    2015-01-01

    The choice of materials for a building with high energy efficiency becomes much more important and strategies for reducing the use of primary energy for the production of materials and components becomes key. The positive trend towards wooden construction is dictated by international guidelines, where a wooden building is an important starting point, not only for low-energy, but also low-emission building with exceptional health and safety aspects. In Europe, the most comprehensiv...

  1. Electric Propulsion Research Building (EPRB)

    Data.gov (United States)

    Federal Laboratory Consortium — The Electric Propulsion Research Building (EPRB) capability centers on its suite of vacuum chambers, which are configured to meet the unique requirements related to...

  2. Diverse interpretations of confidence building

    International Nuclear Information System (INIS)

    This paper explores the variety of operational understandings associated with the term 'confidence building'. Collectively, these understandings constitute what should be thought of as a 'family' of confidence building approaches. This unacknowledged and generally unappreciated proliferation of operational understandings that function under the rubric of confidence building appears to be an impediment to effective policy. The paper's objective is to analyze these different understandings, stressing the important differences in their underlying assumptions. In the process, the paper underlines the need for the international community to clarify its collective thinking about what it means when it speaks of 'confidence building'. Without enhanced clarity, it will be unnecessarily difficult to employ the confidence building approach effectively due to the lack of consistent objectives and common operating assumptions. Although it is not the intention of this paper to promote a particular account of confidence building, dissecting existing operational understandings should help to identify whether there are fundamental elements that define what might be termed 'authentic' confidence building. Implicit here is the view that some operational understandings of confidence building may diverge too far from consensus models to count as meaningful members of the confidence building family. (author)

  3. Lifetime environmental impact of buildings

    CERN Document Server

    Mequignon, Marc

    2014-01-01

    This work discusses the impact of the life of buildings on? sustainable development methods.?The study of the lifespan of the building is used to assess and?manage the environmental impacts associated?with all the stages of a product's life, from raw material extraction?through to repair, maintenance and?? 'end of life' scenarios. While several papers have discussed thegreenhouse gas emissions of buildings,?less research has been done on how these are affected by the lifespan?of the building. This book serves to?highlight the pertinence of this factor and contributes to providing?new ideas on

  4. Descent in buildings (AM-190)

    CERN Document Server

    Mühlherr, Bernhard; Weiss, Richard M

    2015-01-01

    Descent in Buildings begins with the resolution of a major open question about the local structure of Bruhat-Tits buildings. The authors then put their algebraic solution into a geometric context by developing a general fixed point theory for groups acting on buildings of arbitrary type, giving necessary and sufficient conditions for the residues fixed by a group to form a kind of subbuilding or "form" of the original building. At the center of this theory is the notion of a Tits index, a combinatorial version of the notion of an index in the relative theory of algebraic groups. These results

  5. Building guide : how to build Xyce from source code.

    Energy Technology Data Exchange (ETDEWEB)

    Keiter, Eric Richard; Russo, Thomas V.; Schiek, Richard Louis; Sholander, Peter E.; Thornquist, Heidi K.; Mei, Ting; Verley, Jason C.

    2013-08-01

    While Xyce uses the Autoconf and Automake system to configure builds, it is often necessary to perform more than the customary %E2%80%9C./configure%E2%80%9D builds many open source users have come to expect. This document describes the steps needed to get Xyce built on a number of common platforms.

  6. Operating Room Status Monitoring System

    OpenAIRE

    Kane, Francis R.

    1982-01-01

    A system has been devised at The Medical College of Virginia to schedule, monitor, and display the status of twenty-four operating rooms. A switch in each room indicates room status. Room status is matched with scheduling information to provide an airport-like display on 16 video monitors placed about the operating room area. Management and medical information is captured by the system.

  7. Energy Signal Tool for Decision Support in Building Energy Systems

    Energy Technology Data Exchange (ETDEWEB)

    Henze, G. P.; Pavlak, G. S.; Florita, A. R.; Dodier, R. H.; Hirsch, A. I.

    2014-12-01

    A prototype energy signal tool is demonstrated for operational whole-building and system-level energy use evaluation. The purpose of the tool is to give a summary of building energy use which allows a building operator to quickly distinguish normal and abnormal energy use. Toward that end, energy use status is displayed as a traffic light, which is a visual metaphor for energy use that is either substantially different from expected (red and yellow lights) or approximately the same as expected (green light). Which light to display for a given energy end use is determined by comparing expected to actual energy use. As expected, energy use is necessarily uncertain; we cannot choose the appropriate light with certainty. Instead, the energy signal tool chooses the light by minimizing the expected cost of displaying the wrong light. The expected energy use is represented by a probability distribution. Energy use is modeled by a low-order lumped parameter model. Uncertainty in energy use is quantified by a Monte Carlo exploration of the influence of model parameters on energy use. Distributions over model parameters are updated over time via Bayes' theorem. The simulation study was devised to assess whole-building energy signal accuracy in the presence of uncertainty and faults at the submetered level, which may lead to tradeoffs at the whole-building level that are not detectable without submetering.

  8. Construction achievements at building in reprocessing plant

    International Nuclear Information System (INIS)

    We have constructed simultaneously four buildings, AB building, DB building, DC building, and KA building in the spent nuclear fuel reprocessing plant at Rokkasho village in Aomori. We were able to complete the massive and complicated building in the highest quality by the method of prefabrication of site work in a short construction term. Moreover, also in the severe winter season, we practiced construction work intentionally. Consequently, we completed three buildings, AB building, DB building, and DC building without the trouble last year. (author)

  9. Plant status control - with an operational focus

    International Nuclear Information System (INIS)

    In the Nuclear industry, we have done a very good job of designing, developing, constructing, and improving our nuclear facilities. We have, however, often been inconsistent in documenting the details of our facilities, clearly addressing the rules around facility operation, and controlling and tracking the temporary, or permanent changes to our facilities. The reality is, that once we build a facility, we then must operate the facility, for it to be viable. Further we must operate it safely and efficiently for the facility to produce its product, and be acceptable to the public. Unfortunately, when we design and build these large, complicated facilities, we cannot project all the nuances of facility operation, although we can recognize this potential gap, and prepare for it. In order to allow for the complexities of the real world, we must provide the individuals who are tasked with operating our nuclear facilities, with the tools and processes to deal with 'all the nuances' of facility operation. This discussion will focus on the concepts behind a key process for ensuring that we meet our design and operating needs for our facilities, as well as recognizing and dealing with the potential gaps. The key process is 'Plant Status Control', and the discussion will have a primary focus on the needs of the end users, that being the individuals that have the immediate and current accountability for control and safety of the facility, the equipment, the staff, and ultimately the public, that being our Operations staff, and the Shift Manager. (author)

  10. Virtual building environments (VBE) - Applying information modeling to buildings

    Energy Technology Data Exchange (ETDEWEB)

    Bazjanac, Vladimir

    2004-06-21

    A Virtual Building Environment (VBE) is a ''place'' where building industry project staffs can get help in creating Building Information Models (BIM) and in the use of virtual buildings. It consists of a group of industry software that is operated by industry experts who are also experts in the use of that software. The purpose of a VBE is to facilitate expert use of appropriate software applications in conjunction with each other to efficiently support multidisciplinary work. This paper defines BIM and virtual buildings, and describes VBE objectives, set-up and characteristics of operation. It informs about the VBE Initiative and the benefits from a couple of early VBE projects.

  11. INL High Performance Building Strategy

    Energy Technology Data Exchange (ETDEWEB)

    Jennifer D. Morton

    2010-02-01

    High performance buildings, also known as sustainable buildings and green buildings, are resource efficient structures that minimize the impact on the environment by using less energy and water, reduce solid waste and pollutants, and limit the depletion of natural resources while also providing a thermally and visually comfortable working environment that increases productivity for building occupants. As Idaho National Laboratory (INL) becomes the nation’s premier nuclear energy research laboratory, the physical infrastructure will be established to help accomplish this mission. This infrastructure, particularly the buildings, should incorporate high performance sustainable design features in order to be environmentally responsible and reflect an image of progressiveness and innovation to the public and prospective employees. Additionally, INL is a large consumer of energy that contributes to both carbon emissions and resource inefficiency. In the current climate of rising energy prices and political pressure for carbon reduction, this guide will help new construction project teams to design facilities that are sustainable and reduce energy costs, thereby reducing carbon emissions. With these concerns in mind, the recommendations described in the INL High Performance Building Strategy (previously called the INL Green Building Strategy) are intended to form the INL foundation for high performance building standards. This revised strategy incorporates the latest federal and DOE orders (Executive Order [EO] 13514, “Federal Leadership in Environmental, Energy, and Economic Performance” [2009], EO 13423, “Strengthening Federal Environmental, Energy, and Transportation Management” [2007], and DOE Order 430.2B, “Departmental Energy, Renewable Energy, and Transportation Management” [2008]), the latest guidelines, trends, and observations in high performance building construction, and the latest changes to the Leadership in Energy and Environmental Design

  12. Towards more Manageable Coastal Building; Initial Coastal Building Construction Guidelines

    Directory of Open Access Journals (Sweden)

    Roslan Talib

    2011-01-01

    Full Text Available Problem statement: As we may not be aware that the coastal construction is different from inland construction. Building in a coastal environment is different from building in an inland area. In general, buildings in coastal areas must be designed and built to withstand higher loads due to its more extreme conditions. Nowadays, the issue of global warming, uncertainty of global weather and the climate change effect indirectly creating the coastal area with much more expose to extreme condition. Formulate initial guidelines with certain degree of details how coastal construction requirements are different from those for inland construction. Approach: Due to the exposure to higher loads and extreme conditions, these structures in coastal areas will cost more to design, construct, maintain, repair and insure. Proper and right usage of building materials including electrical and mechanical equipments, are crucial in order to minimize damage. Nowadays, the issue of global warming, uncertainty of global weather and the climate change effect indirectly creating the coastal area with much more expose to extreme condition. Feedback has been gathered from the government local engineers who are doing the management of the Government’s local buildings located along the coastal area of Peninsular Malaysia. Data findings through research method, discussion with the suppliers and discussion with coastal buildings maintenance crews also has been done. Results: The research finding discus the specific characteristics that makes for successful coastal buildings focusing in tropical region. Conclusion: We must accept on the idea of building in coastal areas will require more maintenance and upkeep. By having proper coastal building guideline may create more positive awareness in constructing better management coastal buildings and can save time and money to maintain the said structures.

  13. Web based machine status display for INDUS-1 And INDUS-2

    International Nuclear Information System (INIS)

    Web based machine status display for Indus-1 and Indus-2 is designated to provide on-line status of Indus-1 and Indus-2 to the clients located at various places of CAT premises. Presently, this system provides Indus-1 machine status (e.g. beam current, integrated current, beam life-time etc) to the users working in Indus-1 building, but using the web browsers the same information can be accessed throughout the CAT network. This system is basically a part of Indus-1 Control System Web Site which is under construction (partially constructed). (author)

  14. The CMS HF status

    CERN Document Server

    Rahmat, Rahmat

    2012-01-01

    The experiments at the Large Hadron Collider will have to deal with unprecedented radiation levels. The design of the CMS forward calorimetry detector (HF) is now finalized. The present design of CMS calls for the HF calorimeter to be based on quartz fiber technology. It consists of two modules, located symmetrically at about 11 meters from either side of interaction point. They cover the pseudorapidity range 3-5. The length along the beam is 1.65m or 10 nuclear interaction lenghts. Each calorimeter consists of a large steel block that serves as the absorber. Embedded quartz fibers in the steel absorber run parallel to the beam and constitute the active component of the detector. In order to optimize energy resolution for E and ET flows and forward jets, the calorimeter is effectively segmented longitudinally by using two different fiber lengths. The present status will be discussed.

  15. Status of French reactors

    Energy Technology Data Exchange (ETDEWEB)

    Ballagny, A. [Commissariat a l`Energie Atomique, Saclay (France)

    1997-08-01

    The status of French reactors is reviewed. The ORPHEE and RHF reactors can not be operated with a LEU fuel which would be limited to 4.8 g U/cm{sup 3}. The OSIRIS reactor has already been converted to LEU. It will use U{sub 3}Si{sub 2} as soon as its present stock of UO{sub 2} fuel is used up, at the end of 1994. The decision to close down the SILOE reactor in the near future is not propitious for the start of a conversion process. The REX 2000 reactor, which is expected to be commissioned in 2005, will use LEU (except if the fast neutrons core option is selected). Concerning the end of the HEU fuel cycle, the best option is reprocessing followed by conversion of the reprocessed uranium to LEU.

  16. Status of legislation

    International Nuclear Information System (INIS)

    The status of the House legislation, the major differences between the House and Senate legislation and a preview of what is likely to take place during the lame duck session in December are presented. The House legislation provides: long-term program leading toward permanent disposal of nuclear waste; an interim program for storage and for expansion of storage space for spent fuel; provides an R and D component through what is called a test and evaluation facility; an alternative long-term storage program based on a proposal to be completed by the Department of Energy on what's called Monitored Retrievable Storage; full upfront financing of the program through user fees based on contracts between the government and the users of the nuclear waste disposal services

  17. Status of RENO Experiment

    International Nuclear Information System (INIS)

    An experiment, RENO (Reactor Experiment for Neutrino Oscillation), is under construction to measure the smallest and unknown neutrino mixing angle (θ13) using anti-neutrinos emitted from the Yonggwang nuclear power plant in Korea. The experimental setup consists of two identical 16-ton Gadolinium loaded liquid scintillator detectors located near and far from the reactor array to measure the deviations from the inverse square distance law. The experiment is planned to start data-taking in early 2011. An estimated systematic uncertainty associated with the measurement is less than 0.6%. Based on three years of data, it would be sensitive to measure the neutrino mixing angle in the range of sin2(2θ13)>0.02. In this talk, the status of RENO experiment is described.

  18. Status of RENO Experiment

    International Nuclear Information System (INIS)

    The RENO (Reactor Experiment for Neutrino Oscillation) experiment is under construction to measure the smallest neutrino mixing angle θ13 using anti-neutrinos emitted from the Yonggwang nuclear power plant in Korea. The experiment is planning to start data-taking in early 2011 with two identical 16-ton Gadolinium loaded liquid scintillator detectors located near and far from the center of the reactor array. The estimated systematic uncertainty associated with the measurement is less than 0.6%. Based on three years of data, the expected statistical error is about 0.3% and it would be sensitive to measure the neutrino mixing angle in the range, sin2(2θ13)> 0.02. In this talk, the overview and status of RENO experiment are described.

  19. CLIC Status and Outlook

    CERN Document Server

    Stapnes, Stapnes

    2012-01-01

    The Compact Linear Collider study (CLIC) is in the process of completing a Conceptual Design Report (CDR) for a multi-TeV linear electron-positron collider. The CLICconcept is based on high gradient normal-conducting accelerating structures. The RF power for the acceleration of the colliding beams is produced by a novel two beam acceleration scheme, where power is extracted from a high current drive beam that runs parallel with the main linac. In order to establish the feasibility of this concept a number of key issues have been addressed. A short summary of the progress and status of the corresponding studies will be given, as well as an outline of the preparation and work towards an implementation plan by 2016.

  20. ITER EDA project status

    International Nuclear Information System (INIS)

    The status of the ITER design is as presented in the interim design report accepted by the ITER council for considerations by ITER parties. Physical and technical parameters of the machine, conditions of operation of main nuclear systems, corresponding design and material choices are described, with conventional materials selected. To fully utilize the safety and economical potential of fusion advanced materials are necessary. ITER shall and can be built with materials already available. The ITER project and advanced fusion material developments can proceed in parallel. The role of ITER is to establish (experimentally) requirements to these materials and to provide a test bed for their final qualification in fusion reactor environment. To achieve this goal, the first wall/blanket modules test program is foreseen. (orig.)

  1. ITER EDA project status

    Energy Technology Data Exchange (ETDEWEB)

    Chuyanov, V.A. [ITER San Diego JWS, La Jolla, CA (United States)

    1996-10-01

    The status of the ITER design is as presented in the interim design report accepted by the ITER council for considerations by ITER parties. Physical and technical parameters of the machine, conditions of operation of main nuclear systems, corresponding design and material choices are described, with conventional materials selected. To fully utilize the safety and economical potential of fusion advanced materials are necessary. ITER shall and can be built with materials already available. The ITER project and advanced fusion material developments can proceed in parallel. The role of ITER is to establish (experimentally) requirements to these materials and to provide a test bed for their final qualification in fusion reactor environment. To achieve this goal, the first wall/blanket modules test program is foreseen. (orig.).

  2. ITER EDA project status

    Science.gov (United States)

    Chuyanov, V. A.

    1996-10-01

    The status of the ITER design is as presented in the Interim Design Report accepted by the ITER council for considerations by ITER parties. Physical and technical parameters of the machine, conditions of operation of main nuclear systems, corresponding design and material choices are described, with conventional materials selected. To fully utilize the safety and economical potential of fusion advanced materials are necessary. ITER shall and can be built with materials already available. The ITER project and advanced fusion material developments can proceed in parallel. The role of ITER is to establish (experimentally) requirements to these materials and to provide a test bed for their final qualification in fusion reactor environment. To achieve this goal, the first wall/blanket modules test program is foreseen.

  3. 232Z Building seismic assessments

    International Nuclear Information System (INIS)

    The 232Z Building in the 200 West Area has no documented evidence of meeting the structural design requirements for withstanding seismic loadings. The 232Z Building was originally built in 1959. This concrete block structure is south of the 234-5Z Building. The 232Z Building (Incinerator and Leach Facility) start-up occurred in 1961, and the facility has been used for the extraction and recovery of plutonium from contaminated materials. A glovebox incinerator is located in the first floor process area, and was used to incinerate dry wastes from which radioactive materials were then recovered. The design calculations for the original building are not retrievable. The objective of this evaluation is to qualify the 232Z Building in it's current configuration for the appropriate seismic loads in accordance with the requirements of SDC 4.1. The structural capacities of the masonry walls and the reinforced concrete slabs and beams of the 232Z Building exceed the dead, live and seismic demand loadings. The building complies with the UBC seismic loading requirements for the 0.20 g maximum ground acceleration earthquake

  4. Case Studies on Sustainable Buildings

    OpenAIRE

    Hui, Sam CM

    2005-01-01

    This web site is developed with the aim to promote sustainable design and planning of buildings. A knowledge base of case studies and resources has been established to illustrate the sustainable design strategies and features in realistic building projects all over the world. The database of case studies can be searched by project names, locations, design strategies and design features.

  5. Federal Buildings Supplemental Survey 1993

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    The Energy Information Administration (EIA) of the US Department of Energy (DOE) is mandated by Congress to be the agency that collects, analyzes, and disseminates impartial, comprehensive data about energy including the volume consumed, its customers, and the purposes for which it is used. The Federal Buildings Supplemental Survey (FBSS) was conducted by EIA in conjunction with DOE`s Office of Federal Energy Management Programs (OFEMP) to gain a better understanding of how Federal buildings use energy. This report presents the data from 881 completed telephone interviews with Federal buildings in three Federal regions. These buildings were systematically selected using OFEMP`s specifications; therefore, these data do not statistically represent all Federal buildings in the country. The purpose of the FBSS was threefold: (1) to understand the characteristics of Federal buildings and their energy use; (2) to provide a baseline in these three Federal regions to measure future energy use in Federal buildings as required in EPACT; and (3) to compare building characteristics and energy use with the data collected in the CBECS.

  6. Energy efficiency of building envelope

    OpenAIRE

    V.M. Yakubson

    2014-01-01

    November, 12-13th, in Saint-Petersburg the 7th International congress "Energy efficiency. XXI century" took place. The reports were done in breakuo groups according to the various aspects of energy efficiency challenge: HVAC systems, water supply and sewerage systems, gas supply, energy metering. One of the grourps was devoted to thermophysics of buildings and energy effective design of building envelope.

  7. Building Blocks for Personal Brands

    Science.gov (United States)

    Thomas, Lisa Carlucci

    2011-01-01

    In this article, the author discusses the four essential building blocks for personal brands: (1) name; (2) message; (3) channels; and (4) bridges. However, outstanding building materials can only take a person so far. The author emphasizes that vision, determination, faith, a sense of humor, and humility are also required.

  8. Spent nuclear fuel storage building

    International Nuclear Information System (INIS)

    Outer earthquake proof walls of a building are formed in the running direction of a bridge travelling type crane. Inner earthquake proof walls are disposed in the direction perpendicular to the running direction of the crane. An area for constructing an air ventilation tower is formed in the running direction of the crane at the central portion of the building. The area surrounded by the area for constructing air ventilation tower and the earthquake proof inner walls is defined as a cask storage area. Such cask storage areas are disposed symmetrically on both sides of the air ventilation tower. The crane is disposed on the roof of the building, stands on rails which are laid on the outer walls of the building and runs over the air ventilation tower. Since the crane is disposed on the roof of the building, the inner earthquake proof walls of the building can be constructed in the inside of the building, and a high earthquake proofness can be provided to the building itself. (I.N.)

  9. Building Bridges to Spatial Reasoning

    Science.gov (United States)

    Shumway, Jessica F.

    2013-01-01

    Spatial reasoning, which involves "building and manipulating mental representations of two-and three-dimensional objects and perceiving an object from different perspectives" is a critical aspect of geometric thinking and reasoning. Through building, drawing, and analyzing two-and three-dimensional shapes, students develop a foundation…

  10. Building Bounce-Back Kids

    Science.gov (United States)

    Lloyd-Zannini, Lou

    2011-01-01

    In this article, the author talks about building resilience--that ability to push through hardship to success, to rebound from failure, and to "keep on keepin' on" when things seem impossible. The author assert that lots of gifted and talented kids need help building their resilience. In today's world, when striving for mediocrity can seem like…

  11. Simulating Building Fires for Movies

    Science.gov (United States)

    Rodriguez, Ricardo C.; Johnson, Randall P.

    1987-01-01

    Fire scenes for cinematography staged at relatively low cost in method that combines several existing techniques. Nearly realistic scenes, suitable for firefighter training, produced with little specialized equipment. Sequences of scenes set up quickly and easily, without compromising safety because model not burned. Images of fire, steam, and smoke superimposed on image of building to simulate burning of building.

  12. Integrating Environmentally Responsive Elements in Buildings

    OpenAIRE

    Heiselberg, Per; Andresen, Inger; Perino, Marco; van der Aa, Ad

    2006-01-01

    Significant improvement have been achieved on efficiency improvements of specific building elements like the building envelope and building equipment and services and whilst most building elements still offer opportunities for efficiency improvements, the greatest future potential lie with technologies that promote the integration of responsive building elements and building services in integrated building concepts. In order to address some of these issues an international research effort, IE...

  13. Present status of ESRF

    International Nuclear Information System (INIS)

    The European Synchrotron Radiation Source ESRF is now in its 3rd year of construction: Half of the machine elements have been ordered; construction of the buildings to accomodate the machine and the experiments has been started; the layout of the first set of beam lines has been defined. The first stored beam is foreseen for mid 1992. After two years of commissioning the first external users are expected for mid 1994. At this time 7-10 beam lines will be available while the total of 30 beam lines, mostly on insertion devices, will be finished by 1998. Additional beam lines on bending magnets will be constructed and used by external groups. (author)

  14. California commercial building energy benchmarking

    Energy Technology Data Exchange (ETDEWEB)

    Kinney, Satkartar; Piette, Mary Ann

    2003-07-01

    Building energy benchmarking is the comparison of whole-building energy use relative to a set of similar buildings. It provides a useful starting point for individual energy audits and for targeting buildings for energy-saving measures in multiple-site audits. Benchmarking is of interest and practical use to a number of groups. Energy service companies and performance contractors communicate energy savings potential with ''typical'' and ''best-practice'' benchmarks while control companies and utilities can provide direct tracking of energy use and combine data from multiple buildings. Benchmarking is also useful in the design stage of a new building or retrofit to determine if a design is relatively efficient. Energy managers and building owners have an ongoing interest in comparing energy performance to others. Large corporations, schools, and government agencies with numerous facilities also use benchmarking methods to compare their buildings to each other. The primary goal of Task 2.1.1 Web-based Benchmarking was the development of a web-based benchmarking tool, dubbed Cal-Arch, for benchmarking energy use in California commercial buildings. While there were several other benchmarking tools available to California consumers prior to the development of Cal-Arch, there were none that were based solely on California data. Most available benchmarking information, including the Energy Star performance rating, were developed using DOE's Commercial Building Energy Consumption Survey (CBECS), which does not provide state-level data. Each database and tool has advantages as well as limitations, such as the number of buildings and the coverage by type, climate regions and end uses. There is considerable commercial interest in benchmarking because it provides an inexpensive method of screening buildings for tune-ups and retrofits. However, private companies who collect and manage consumption data are concerned that the

  15. Biogas building directions

    Energy Technology Data Exchange (ETDEWEB)

    Eggeling, G.; Guldager, R.; Hilliges, G.; Tietjen, C.; Werner, U.; Guldager, H.; Sasse, L.

    The purpose of this book is to approach the people living and working in the rural regions of developing countries with a technology enabling them to use their resources by their proper means in a way that they dispose of a cheap and inexhaustible source of energy and fertilizer. These building directives for biogas plants shall concretely give the fundamental information for the use of this technology and be a practical support in do-it-yourself construction of biogas plants by its intelligible way of description owing to designs and popular language. These directives are part of a work performed by German and Indian experts during two years working up the biogas technology in countries of the Third World and in industrial countries. The regulations have been discussed at an international workshop in Bremen with more than 60 experts from countries of all continents meeting to discuss the application of biogas plants. The result has been documented in the ''Report on the International Biogas-Workshop Bremen''.

  16. Building a crystal palace

    CERN Multimedia

    2007-01-01

    The end-caps of the CMS electromagnetic calorimeter (ECAL) take shape as the first quadrant was completed on Wednesday 3 October. 1831 crystals, organised into five by five blocks named ‘supercrystals’, make up the first quadrant of Dee 1.With the 61,200-crystal barrel of its electromagnetic calorimeter (ECAL) complete, CMS is now building the endcaps, on the tenth anniversary of their initial design. Crystals for the endcaps were the last to be made, so the race is now on to have them all in place and ready for the turn-on of the LHC next year. Assembly of the first of eight quadrants began in June and crystal mounting was completed on Wednesday 3 October. Each crystal is transparent, has a volume just larger than a CERN coffee cup yet weighs a huge 1.5kg. 1831 of these lead tungstate crystals went into the first quadrant from a total 14,648 in the endcaps. The lead and tungsten account for 86% of each crystal’s weight, but as project leader Dave Cockerill expl...

  17. Energy Performance of Buildings

    DEFF Research Database (Denmark)

    Heiselberg, Per

    2007-01-01

    "Sustainable development" has been defined best by the Brundtland Commission as "development that meets the needs of the present without compromising the ability of future generations to meet their own needs". Adequate and affordable energy supplies have been key to economic development and are c......"Sustainable development" has been defined best by the Brundtland Commission as "development that meets the needs of the present without compromising the ability of future generations to meet their own needs". Adequate and affordable energy supplies have been key to economic development...... and are central to improving social and economic well- being, and human welfare and raising living standards. Even if energy is essential for development, it is only a means to an end. The end is good health, high living standards, a sustainable economy and a clean environment. The European Climate change...... programme (ECCP) was established in June 2000 to help identify the most environmentally cost-effective measures enabling the EU to meet its target under the Kyoto Protocol, namely an 8% reduction in greenhouse gas emissions from 1990 levels by 2012. Energy use in buildings accounts for almost half of all CO...

  18. AP600 Shield building

    International Nuclear Information System (INIS)

    In order to minimize capital costs and save time in the global construction time schedule for the AP600 Nuclear Power Plant, planned in 36 months from excavation up to the fuel charging, ANSALDO has developed an innovative Shield Building Conical Roof design having the following basic characteristics: i) can be erected approximately in less than two months; ii) allows the functionality of the Passive Containment Cooling System (PCSS) located in the PCCS tank and in the Valve Room anchored directly to the conical roof itself; iii) satisfies the structural loads design as Safe Shutdown Earthquake, or the Aircraft Crash and both integrated with the sloshing analysis for the tank located at the top of the conical roof. The most important aspects of this new roof are: a) use of prefabricated precast panels; b) address the erection of the formworks using temporary structures having the capability of becoming final elements; c) develop a modular rebars sizing and design in order to perform the most important portion of the job in the workshop; d) second pouring construction sequence assuring full integration with the formwork function; e) modular construction of the PCSS tank at the top of the conical roof. An interesting evaluation has been also performed in calculating sloshing phenomenon in the PCSS tank by comparing detailed 3D Finite Element Model approach and simplified qualified formulas dedicated to this phenomenon. (author). 2 figs

  19. Nuclear reactor building

    Science.gov (United States)

    Gou, Perng-Fei; Townsend, Harold E.; Barbanti, Giancarlo

    1994-01-01

    A reactor building for enclosing a nuclear reactor includes a containment vessel having a wetwell disposed therein. The wetwell includes inner and outer walls, a floor, and a roof defining a wetwell pool and a suppression chamber disposed thereabove. The wetwell and containment vessel define a drywell surrounding the reactor. A plurality of vents are disposed in the wetwell pool in flow communication with the drywell for channeling into the wetwell pool steam released in the drywell from the reactor during a LOCA for example, for condensing the steam. A shell is disposed inside the wetwell and extends into the wetwell pool to define a dry gap devoid of wetwell water and disposed in flow communication with the suppression chamber. In a preferred embodiment, the wetwell roof is in the form of a slab disposed on spaced apart support beams which define therebetween an auxiliary chamber. The dry gap, and additionally the auxiliary chamber, provide increased volume to the suppression chamber for improving pressure margin.

  20. Building an innovation factory.

    Science.gov (United States)

    Hargadon, A; Sutton, R I

    2000-01-01

    New ideas are the precious currency of the new economy, but generating them doesn't have to be a mysterious process. The image of the lone genius inventing from scratch is a romantic fiction. Businesses that constantly innovate have systematized the production and testing of new ideas, and the system can be replicated by practically any organization. The best innovators use old ideas as the raw materials for new ideas, a strategy the authors call knowledge brokering. The system for sustaining innovation is the knowledge brokering cycle, and the authors discuss its four parts. The first is capturing good ideas from a wide variety of sources. The second is keeping those ideas alive by playing with them, discussing them, and using them. Imagining new uses for old ideas is the third part--some knowledge brokers encourage cross-pollination by creating physical layouts that allow, or even force, people to interact with one another. The fourth is turning promising concepts into real services, products, processes, or business models. Companies can use all or part of the cycle. Large companies in particular desperately need to move ideas from one place to another. Some will want to build full-fledged consulting groups dedicated to internal knowledge brokering. Others can hire people who have faced problems similar to the companies' current problems. The most important lesson is that business leaders must change how they think about innovation, and they must change how their company cultures reflect that thinking. PMID:11183977

  1. Strengthening Building Retrofit Markets

    Energy Technology Data Exchange (ETDEWEB)

    Templeton, Mary [Michigan Saves; Jackson, Robert [Michigan Energy Office

    2014-04-15

    The Business Energy Financing (BEF) program offered commercial businesses in Michigan affordable financing options and other incentives designed to support energy efficiency improvements. We worked through partnerships with Michigan utilities, lenders, building contractors, trade associations, and other community organizations to offer competitive interest rates and flexible financing terms to support energy efficiency projects that otherwise would not have happened. The BEF program targeted the retail food market, including restaurants, grocery stores, convenience stores, and wholesale food vendors, with the goal of achieving energy efficiency retrofits for 2 percent of the target market. We offered low interest rates, flexible payments, easy applications and approval processes, and access to other incentives and rebates. Through these efforts, we sought to help customers strive for energy savings retrofits that would save 20 percent or more on their energy use. This program helped Michigan businesses reduce costs by financing energy efficient lighting, heating and cooling systems, insulation, refrigeration, equipment upgrades, and more. Businesses completed the upgrades with the help of our authorized contractors, and, through our lending partners, we provided affordable financing options.

  2. Adaptive building skin structures

    International Nuclear Information System (INIS)

    The concept of adaptive and morphing structures has gained considerable attention in the recent years in many fields of engineering. In civil engineering very few practical applications are reported to date however. Non-conventional structural concepts like deployable, inflatable and morphing structures may indeed provide innovative solutions to some of the problems that the construction industry is being called to face. To give some examples, searches for low-energy consumption or even energy-harvesting green buildings are amongst such problems. This paper first presents a review of the above problems and technologies, which shows how the solution to these problems requires a multidisciplinary approach, involving the integration of architectural and engineering disciplines. The discussion continues with the presentation of a possible application of two adaptive and dynamically morphing structures which are proposed for the realization of an acoustic envelope. The core of the two applications is the use of a novel optimization process which leads the search for optimal solutions by means of an evolutionary technique while the compatibility of the resulting configurations of the adaptive envelope is ensured by the virtual force density method

  3. Integrated Building Management System (IBMS)

    Energy Technology Data Exchange (ETDEWEB)

    Anita Lewis

    2012-07-01

    This project provides a combination of software and services that more easily and cost-effectively help to achieve optimized building performance and energy efficiency. Featuring an open-platform, cloud- hosted application suite and an intuitive user experience, this solution simplifies a traditionally very complex process by collecting data from disparate building systems and creating a single, integrated view of building and system performance. The Fault Detection and Diagnostics algorithms developed within the IBMS have been designed and tested as an integrated component of the control algorithms running the equipment being monitored. The algorithms identify the normal control behaviors of the equipment without interfering with the equipment control sequences. The algorithms also work without interfering with any cooperative control sequences operating between different pieces of equipment or building systems. In this manner the FDD algorithms create an integrated building management system.

  4. Data management for biofied building

    Science.gov (United States)

    Matsuura, Kohta; Mita, Akira

    2015-03-01

    Recently, Smart houses have been studied by many researchers to satisfy individual demands of residents. However, they are not feasible yet as they are very costly and require many sensors to be embedded into houses. Therefore, we suggest "Biofied Building". In Biofied Building, sensor agent robots conduct sensing, actuation, and control in their house. The robots monitor many parameters of human lives such as walking postures and emotion continuously. In this paper, a prototype network system and a data model for practical application for Biofied Building is pro-posed. In the system, functions of robots and servers are divided according to service flows in Biofield Buildings. The data model is designed to accumulate both the building data and the residents' data. Data sent from the robots and data analyzed in the servers are automatically registered into the database. Lastly, feasibility of this system is verified through lighting control simulation performed in an office space.

  5. 327 Building hazard baseline document

    International Nuclear Information System (INIS)

    This document identifies the hazards in the 327 Building at the time that a facility walk through was performed during FY99, presents a PHA of stabilization and deactivation activities, and provides a basis for the hazard evaluation and accident analysis that will be developed in the 327 Building Basis for Interim Operation (BIO). Activities addressed in this hazard baseline document include: (1) Stabilization and deactivation activities in preparation for eventual decommissioning of the 327 Building and the routine handling, processing, and shipment of waste to support these activities. (2) 324/327 Building Minimum Safe Project engineering and maintenance activities to maintain the building and systems viable--especially the Safety SSCs--to allow stabilization, deactivation, and waste handling activities with a minimum of risk to workers, the public, and the environment

  6. Building America Expert Meeting Report: Hydronic Heating in Multifamily Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Dentz, J.

    2011-10-01

    The topic of this expert meeting was cost-effective controls and distribution retrofit options for hot water and steam space heating systems in multi-family buildings with the goals of reducing energy waste and improving occupant comfort. The U.S. Department of Energy's Building America program develops technologies with the goal of reducing energy use by 30% to 50% in residential buildings. Toward this goal, the program sponsors 'Expert Meetings' focused on specific building technology topics. The meetings are intended to sharpen Building America research priorities, create a forum for sharing information among industry leaders and build partnerships with professionals and others that can help support the program's research needs and objectives. The topic of this expert meeting was cost-effective controls and distribution retrofit options for hot water and steam space heating systems in multifamily buildings with the goals of reducing energy waste and improving occupant comfort. The objectives of the meeting were to: (1) Share knowledge and experience on new and existing solutions: what works, what doesn't and why, and what's new; (2) Understand the market barriers to currently offered solutions: what disconnects exist in the market and what is needed to overcome or bridge these gaps; and (3) Identify research needs.

  7. Building Quality, Building Green: Conventions Theory and Industry Transformation

    Directory of Open Access Journals (Sweden)

    Julie Cidell

    2012-01-01

    Full Text Available Conventions theory was developed in part to explain how heterogeneous actors with asymmetrical information manage to carry out economic transactions. In particular, how do these actors work together to reduce uncertainty about the quality of the commodities involved? While most applications of conventions theory have been in the agro-food industry, this paper looks at the newly developing green building industry as an example of economic production that relies on multiple constructions of quality in its production and consumption processes. Previous work has shown that conflicts over quality often arise when the parties involved are operating under different conventions, a danger with the multiple actors that must cooperate to produce (and consume a green building. Furthermore, in the case of green buildings, uncertainty about a product's performance does not end at the point of transaction; the quality of many of the materials or processes involved can only be proven over time. I argue that the producers of green buildings and green building materials have overcome the problems of a uncertainty over time and b conflicts over the meaning of quality by drawing on all four conventions simultaneously. Furthermore, this simultaneous incorporation of trust, third-party standards, price, and the common good, as enacted through the Leadership in Energy and Environmental Design (LEED standards of the U.S. Green Building Council (USGBC, is one of the main reasons for the phenomenal growth of the green building industry among public, private, and non-profit clients.

  8. Energy use in office buildings

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-10-01

    This is the report on Task IB, Familiarization with Additional Data Collection Plans of Annual Survey of BOMA Member and Non-Member Buildings in 20 Cities, of the Energy Use in Office Buildings project. The purpose of the work was to monitor and understand the efforts of the Building Owners and Managers Association International (BOMA) in gathering an energy-use-oriented data base. In order to obtain an improved data base encompassing a broad spectrum of office space and with information suitable for energy analysis in greater detail than is currently available, BOMA undertook a major data-collection effort. Based on a consideration of geographic area, climate, population, and availability of data, BOMA selected twenty cities for data collection. BOMA listed all of the major office space - buildings in excess of 40,000 square feet - in each of the cities. Tax-assessment records, local maps, Chamber of Commerce data, recent industrial-development programs, results of related studies, and local-realtor input were used in an effort to assemble a comprehensive office-building inventory. In order to verify the accuracy and completeness of the building lists, BOMA assembled an Ad-Hoc Review Committee in each city to review the assembled inventory of space. A questionnaire on office-building energy use and building characteristics was developed. In each city BOMA assembled a data collection team operating under the supervision of its regional affiliate to gather the data. For each city a random sample of buildings was selected, and data were gathered. Responses for over 1000 buildings were obtained.

  9. Status as a Valued Resource

    Science.gov (United States)

    Huberman, Bernardo A.; Loch, Christoph H.; Onculer, Ayse

    2004-01-01

    The striving for status has long been recognized in sociology and economics. Extensive theoretical arguments and empirical evidence propose that people view status as a sign of competence and pursue it as a means to achieve power and resources. A small literature, however, based on arguments from biology and evolutionary psychology, proposes that…

  10. Energy Efficiency Building Code for Commercial Buildings in Sri Lanka

    International Nuclear Information System (INIS)

    1.1.1 To encourage energy efficient design or retrofit of commercial buildings so that they may be constructed, operated, and maintained in a manner that reduces the use of energy without constraining the building function, the comfort, health, or the productivity of the occupants and with appropriate regard for economic considerations. 1.1.2 To provide criterion and minimum standards for energy efficiency in the design or retrofit of commercial buildings and provide methods for determining compliance with them. 1.1.3 To encourage energy efficient designs that exceed these criterion and minimum standards

  11. Energy Efficiency Building Code for Commercial Buildings in Sri Lanka

    Energy Technology Data Exchange (ETDEWEB)

    Busch, John; Greenberg, Steve; Rubinstein, Francis; Denver, Andrea; Rawner, Esther; Franconi, Ellen; Huang, Joe; Neils, Danielle

    2000-09-30

    1.1.1 To encourage energy efficient design or retrofit of commercial buildings so that they may be constructed, operated, and maintained in a manner that reduces the use of energy without constraining the building function, the comfort, health, or the productivity of the occupants and with appropriate regard for economic considerations. 1.1.2 To provide criterion and minimum standards for energy efficiency in the design or retrofit of commercial buildings and provide methods for determining compliance with them. 1.1.3 To encourage energy efficient designs that exceed these criterion and minimum standards.

  12. Better Buildings Neighborhood Program: BetterBuildings Lowell Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Heslin, Thomas

    2014-01-31

    The City of Lowell set four goals at the beginning of the Better Buildings Neighborhood Program: 1. Improve the Downtown Historic Park District’s Carbon Footprint 2. Develop a sustainable and replicable model for energy efficiency in historic buildings 3. Create and retain jobs 4. Promote multi-stakeholder partnerships The City of Lowell, MA was awarded $5 million in May 2010 to conduct energy efficiency retrofits within the downtown National Historical Park (NHP). The City’s target was to complete retrofits in 200,000 square feet of commercial space and create 280 jobs, while adhering to the strict historical preservation regulations that govern the NHP. The development of a model for energy efficiency in historic buildings was successfully accomplished. BetterBuildings Lowell’s success in energy efficiency in historic buildings was due to the simplicity of the program. We relied strongly on the replacement of antiquated HVAC systems and air sealing and a handful of talented energy auditors and contractors. BetterBuildings Lowell was unique for the Better Buildings Neighborhood Program because it was the only program that focused solely on commercial properties. BetterBuildings Lowell did target multi-family properties, which were reported as commercial, but the majority of the building types and uses were commercial. Property types targeted were restaurants, office buildings, museums, sections of larger buildings, mixed use buildings, and multifamily buildings. This unique fabric of building type and use allows for a deeper understanding to how different properties use energy. Because of the National Historical Park designation of downtown Lowell, being able to implement energy efficiency projects within a highly regulated historical district also provided valuable research and precedent proving energy efficiency projects can be successfully completed in historical districts and historical buildings. Our program was very successful in working with the local

  13. Building damage in Dujiangyan during Wenchuan Earthquake

    Institute of Scientific and Technical Information of China (English)

    Zhang Minzheng; Jin Yingjie

    2008-01-01

    A field damage survey of 1,005 buildings damaged by the Wenchuan Earthquake in Dujiangyan City was carried out and the resulting data was analyzed using the statistical method. It is shown that buildings that were seismically designed achieved the desired seismic fortification target; they sustained less damage than the non-seismically designed buildings. Among the seismically designed buildings investigated, RC frame buildings performed the best in terms of seismic resistance. Masonry buildings with a ground story of RC frame structure were the second best, and masonry buildings performed the worst. Considering building height, multistory buildings sustained more severe damage than high-rise buildings and 2-and 3-story buildings. Compared to residential buildings, public buildings, such as schools and hospitals, suffered more severe damage.

  14. NASA, Building Tomorrow's Future

    Science.gov (United States)

    Mango, Edward

    2011-01-01

    We, as NASA, continue to Dare Mighty Things. Here we are in October. In my country, the United States of America, we celebrate the anniversary of Christopher Columbus's arrival in the Americas, which occurred on October 12, 1492. His story, although happening over 500 years ago, is still very valid today. It is a part of the American spirit; part of the international human spirit. Columbus is famous for discovering the new world we now call America, but he probably never envisioned what great discoveries would be revealed many generations later. But in order for Columbus to begin his great adventure, he needed a business plan. Ho would he go about obtaining the funds and support necessary to build, supply, and man the ships required for his travels? He had a lot of obstacles and distractions. He needed a strong, internal drive to achieve his plans and recruit a willing crew of explorers also ready to risk their all for the unknown journey ahead. As Columbus set sail, he said "By prevailing over all obstacles and distractions, one may unfailingly arrive at his chosen goal or destination." Columbus may not have known he was on a journey for all human exploration. Recently, Charlie Bolden, the NASA Administrator, said, "Human exploration is and has always been about making life better for humans on Earth." Today, NASA and the U.S. human spaceflight program hold many of the same attributes as did Columbus and his contemporaries - a willing, can-do spirit. We are on the threshold of exciting new times in space exploration. Like Columbus, we need a business plan to take us into the future. We need to design the best ships and utilize the best designers, with their past knowledge and experience, to build those ships. We need funding and support from governments to achieve these goals of space exploration into the unknown. NASA does have that business plan, and it is an ambitious plan for human spaceflight and exploration. Today, we have a magnificent spaceflight

  15. BUILDING MATERIALS RECLAMATION PROGRAM

    Energy Technology Data Exchange (ETDEWEB)

    David C. Weggel; Shen-En Chen; Helene Hilger; Fabien Besnard; Tara Cavalline; Brett Tempest; Adam Alvey; Madeleine Grimmer; Rebecca Turner

    2010-08-31

    This report describes work conducted on the Building Materials Reclamation Program for the period of September 2008 to August 2010. The goals of the project included selecting materials from the local construction and demolition (C&D) waste stream and developing economically viable reprocessing, reuse or recycling schemes to divert them from landfill storage. Educational resources as well as conceptual designs and engineering feasibility demonstrations were provided for various aspects of the work. The project was divided into two distinct phases: Research and Engineering Feasibility and Dissemination. In the Research Phase, a literature review was initiated and data collection commenced, an advisory panel was organized, and research was conducted to evaluate high volume C&D materials for nontraditional use; five materials were selected for more detailed investigations. In the Engineering Feasibility and Dissemination Phase, a conceptual study for a regional (Mecklenburg and surrounding counties) collection and sorting facility was performed, an engineering feasibility project to demonstrate the viability of recycling or reuse schemes was created, the literature review was extended and completed, and pedagogical materials were developed. Over the two-year duration of the project, all of the tasks and subtasks outlined in the original project proposal have been completed. The Final Progress Report, which briefly describes actual project accomplishments versus the tasks/subtasks of the original project proposal, is included in Appendix A of this report. This report describes the scientific/technical aspects (hypotheses, research/testing, and findings) of six subprojects that investigated five common C&D materials. Table 1 summarizes the six subprojects, including the C&D material studied and the graduate student and the faculty advisor on each subproject.

  16. Building Materials Reclamation Program

    International Nuclear Information System (INIS)

    This report describes work conducted on the Building Materials Reclamation Program for the period of September 2008 to August 2010. The goals of the project included selecting materials from the local construction and demolition (C and D) waste stream and developing economically viable reprocessing, reuse or recycling schemes to divert them from landfill storage. Educational resources as well as conceptual designs and engineering feasibility demonstrations were provided for various aspects of the work. The project was divided into two distinct phases: Research and Engineering Feasibility and Dissemination. In the Research Phase, a literature review was initiated and data collection commenced, an advisory panel was organized, and research was conducted to evaluate high volume C and D materials for nontraditional use; five materials were selected for more detailed investigations. In the Engineering Feasibility and Dissemination Phase, a conceptual study for a regional (Mecklenburg and surrounding counties) collection and sorting facility was performed, an engineering feasibility project to demonstrate the viability of recycling or reuse schemes was created, the literature review was extended and completed, and pedagogical materials were developed. Over the two-year duration of the project, all of the tasks and subtasks outlined in the original project proposal have been completed. The Final Progress Report, which briefly describes actual project accomplishments versus the tasks/subtasks of the original project proposal, is included in Appendix A of this report. This report describes the scientific/technical aspects (hypotheses, research/testing, and findings) of six subprojects that investigated five common C and D materials. Table 1 summarizes the six subprojects, including the C and D material studied and the graduate student and the faculty advisor on each subproject.

  17. SCIENTIFIC STATUS OF DIDACTICS

    Directory of Open Access Journals (Sweden)

    I. M. Osmolovskaya

    2015-03-01

    Full Text Available The research is aimed at scientific justification of didactics referred to the social and humanitarian field of knowledge. The author deals with the scientific character criteria (verity, inter-subjectivity, systemacity and validity taking into account different scientific rationality types (classical and nonclassical and identifying post-modernism influence on didactics. Objectives and results of research. Attempts are made to systematize the didactic knowledge and identify its components and structure. Didactic concepts are classified in accordance with its objects: teaching process by the whole, its individual components or educative process aspects that enable to form definite teaching views, studying it from the specific positions. The author singles out holistic-didactic, component and aspect concepts; and specifies the concept of didactic systems and models with its hierarchy. The author highlights the didactic knowledge increment. Apart from traditional empirical theoretical researches, the author’s attention is drawn to the academic pursuit such as a scientific project based on the didactic object specificity of the teaching process which is fully human controlled and realized and doesn’texist without human being. It is shown that basic theoretical ideas of scientific projects are itemized, concretized and enlarged during co-current educative practice, i.e. an adhesion of theory and practice occurs.It is stressed that there are two special directions of didactic development multidimensionality: 1. extension of its semantic field in the context of modern socio-cultural conditions; 2. increase of scientific status related to a conceptual framework improvement, empirically accumulated information arrangement, new hypotheses, theories and concepts’ development. Scientific novelty. The research findings demonstrate well-reasoned statement of the didactics’ scientific status, its particular components and structure

  18. Energy efficiency buildings program, FY 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-05-01

    A separate abstract was prepared on research progress in each group at LBL in the energy efficient buildings program. Two separate abstracts were prepared for the Windows and Lighting Program. Abstracts prepared on other programs are: Energy Performance of Buildings; Building Ventilation and Indoor Air Quality Program; DOE-21 Building Energy Analysis; and Building Energy Data Compilation, Analysis, and Demonstration. (MCW)

  19. Building 774: open for business

    CERN Multimedia

    CERN Bulletin

    2015-01-01

    In July 2012, the demolition of Building 936 on the Prévessin site marked the start of the Building 774 project. On 23 February, less than three years later, the new 3900 m2 building was handed over to the BE department.   The brand new Building 774. (Credits: Francesco Soppelsa) Located near to the CERN Control Centre, Building 774 contains offices, laboratories and meeting rooms, as well as a huge public area consisting of a 104-seat auditorium, a changing room/shower area in the basement and a pleasant cafeteria open from 8 a.m. to 5 p.m., offering a wide range of refreshments including hot meals at lunchtime. “There were a few twists and turns during the construction of this building, but it all turned out well in the end!" says Michael Poehler, a member of the GS-SE group and the technical coordinator of the project. (Credits: Francesco Soppelsa) The 120 occupants of the building have just moved into their brand new home, bringing all the members of the...

  20. Cognitive Study of Building Metaphor

    Institute of Scientific and Technical Information of China (English)

    牛惠君

    2015-01-01

    Metaphor is a universal phenomenon,the traditional metaphor studies it as a means of rhetoric,but metaphor of modern sees it as a cognitive phenomenon.In our life most of the everyday language is metaphor,our mind is also the metaphor.Meta-phor has become an indispensable tool for understanding the world.There are a lot of “building”metaphorical expressions in the life, construction is an important component of people’s lives. K?vecses (2002)discussed briefly some conceptual metaphors of the construction in English,Deignan (2001)make a compre-hensive study on building metaphors which underlie some metaphor expression of “building and construction”.Lan Chun (2003)only referred to “theory is building”,but the concept of “life,relationships”can be understood through building concept,these relative ab-stract concepts can be understood by clear concrete building concept.Hence the studies of building metaphors have not been systematic and comprehensive,people seldom study it.We plan to give a contrastive study of building metaphors.This will further deepen peo-ple’s understanding of building metaphors and enrich the cognitive studies of metaphor.

  1. Material Efficiency of Building Construction

    Directory of Open Access Journals (Sweden)

    Antti Ruuska

    2014-07-01

    Full Text Available Better construction and use of buildings in the European Union would influence 42% of final energy consumption, about 35% of our greenhouse gas emissions and more than 50% of all extracted materials. It could also help to save up to 30% of water consumption. This paper outlines and draws conclusions about different aspects of the material efficiency of buildings and assesses the significance of different building materials on the material efficiency. The research uses an extensive literature study and a case-study in order to assess: should the depletion of materials be ignored in the environmental or sustainability assessment of buildings, are the related effects on land use, energy use and/or harmful emissions significant, should related indicators (such as GHGs be used to indicate the material efficiency of buildings, and what is the significance of scarce materials, compared to the use of other building materials. This research suggests that the material efficiency should focus on the significant global impacts of material efficiency; not on the individual factors of it. At present global warming and greenhouse gas emissions are among the biggest global problems on which material efficiency has a direct impact on. Therefore, this paper suggests that greenhouse gas emissions could be used as an indicator for material efficiency in building.

  2. Building Footprints, Building footprints of all building locations in Johnson County, updated off Orthoimarty, Published in unknown, Johnson County AIMS.

    Data.gov (United States)

    NSGIC GIS Inventory (aka Ramona) — This Building Footprints dataset, was produced all or in part from Orthoimagery information as of unknown. It is described as 'Building footprints of all building...

  3. Maternal Teaching Talk within Families of Mexican Descent: Influences of Task and Socioeconomic Status.

    Science.gov (United States)

    Eisenberg, Ann R.

    2002-01-01

    The interactions of 20 middle-class and 20 working-class Mexican American mothers and their 4-year-old children were observed during a school-type construction task (block building) and a home-type construction task (baking biscuits). Both task and socioeconomic status had significant effects on mothers' and children's conversations and behaviors.…

  4. Environmental Evaluation of Building Materials of 5 Slovak Buildings

    Science.gov (United States)

    Porhincak, Milan; Estokova, Adriana

    2013-11-01

    Building activity has recently led to the deterioration of environment and has become unsustainable. Several strategies have been introduced in order to minimize consumption of energy and resulting CO2 emissions having their origin in the operational phase. But also other stages of Life Cycle should are important to identify the overall environmental impact of construction sector. In this paper 5 similar Slovak buildings (family houses) were analyzed in terms of environmental performance of building materials used for their structures. Evaluation included the weight of used materials, embodied energy and embodied CO2 and SO2 emissions. Analysis has proven that the selection of building materials is an important factor which influences the environmental profile. Findings of the case study indicated that materials like concrete, ceramic or thermal insulation materials based on polystyrene and mineral wool are ones with the most negative environmental impact.

  5. Digital Handover of Data from Building Projects to Building Operation

    DEFF Research Database (Denmark)

    Jensen, Per Anker

    2006-01-01

    and construction and on the other side in building opera-tion and facilities management. In Denmark the government has launched a development program called Digital Construction and one of the projects concerns specifying require-ments for building clients in relation to digital handover of data from construction...... pro-jects to building operation. This project started in 2004 with research and analyses fol-lowed by development of a proposal for client requirements and in 2005 a first test on a real construction project has been carried out. After revision of the requirements a second test will be started early...... by a consortium called DACaPo consisting of a building client/facilities manager, a consulting company, a contractor and a university institute. This paper presents some of the results from the project with the main focus on the initial research....

  6. Buildings-to-Grid Technical Opportunities: From the Buildings Perspective

    Energy Technology Data Exchange (ETDEWEB)

    Kiliccote, Sila [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Piette, Mary Ann [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2014-03-28

    This paper describes technologies and systems needed to transform buildings from the current state of siloed resources into transparent, reliable resources that participate in and benefit from an integrated "transactive energy" system.

  7. Toward a virtual building laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Klems, J.H.; Finlayson, E.U.; Olsen, T.H.; Banks, D.W.; Pallis, J.M.

    1999-03-01

    In order to achieve in a timely manner the large energy and dollar savings technically possible through improvements in building energy efficiency, it will be necessary to solve the problem of design failure risk. The most economical method of doing this would be to learn to calculate building performance with sufficient detail, accuracy and reliability to avoid design failure. Existing building simulation models (BSM) are a large step in this direction, but are still not capable of this level of modeling. Developments in computational fluid dynamics (CFD) techniques now allow one to construct a road map from present BSM's to a complete building physical model. The most useful first step is a building interior model (BIM) that would allow prediction of local conditions affecting occupant health and comfort. To provide reliable prediction a BIM must incorporate the correct physical boundary conditions on a building interior. Doing so raises a number of specific technical problems and research questions. The solution of these within a context useful for building research and design is not likely to result from other research on CFD, which is directed toward the solution of different types of problems. A six-step plan for incorporating the correct boundary conditions within the context of the model problem of a large atrium has been outlined. A promising strategy for constructing a BIM is the overset grid technique for representing a building space in a CFD calculation. This technique promises to adapt well to building design and allows a step-by-step approach. A state-of-the-art CFD computer code using this technique has been adapted to the problem and can form the departure point for this research.

  8. Status for CASA NOVA konsortiet

    DEFF Research Database (Denmark)

    Bonke, Sten

    1997-01-01

    The report reviews the development projects and the results hitherto achieved by the design and build organisation CASA NOVA which is one of four consortia within the R&D programme "Process and Product Development in Building", financed by the Ministry of Industry and the Ministry of Housing....

  9. The Status of Glueballs

    Energy Technology Data Exchange (ETDEWEB)

    Lindenbaum, S.J. [Brookhaven National Lab., Upton, NY (United States)]|[City Coll., New York, NY (United States)

    1993-04-14

    The Status of Glueballs is presented considering that most popular candidates from among the isoscalars in the J{sup PC} = 0{sup ++}, 0{sup {minus}+} and 2{sup ++} channels. It is shown that in the 0{sup ++} channel the f{sub 0}(1720) which was discovered earlier (the S*{prime}(1720)) at BNL is highly likely the same state as the SLAC {theta}(1720) now that its spin has been found to be 0 instead of the 2 claimed for a long period. In the {sup ++} channel there is likely a complex of 2-3 states {zeta}/{eta}(1280), {lambda}/{eta}(1420) and {iota}/{eta}(1520) involving at least one extra isosclar. In the 2{sup ++}, the g{sub T}(2010), g{sub T}{prime}(2300) and g{sub T}{double_prime}(2340) {phi}{phi} states found in {pi}{sup {minus}} p {yields} {phi}{phi}n (OZI forbidden glueball filter channel) strikingly, approximately, completely break the OZI suppression and comprise within the errors all the {phi}{phi} cross-section. The only viable explanation of these states in the context of QCD is that they are produced by 1-3 primary 2{sup ++} glueballs. All alternate explanations in the past 15 years have failed.

  10. LIL laser performance status

    International Nuclear Information System (INIS)

    The Laser Integration Line (LIL) was first designed as a prototype to validate the concepts and the laser architecture of the Laser MegaJoule (LMJ). The LIL facility is a 4-beam laser representing a quad structure of the LMJ. A set of test campaigns were conducted to safely ramp up laser performance. The main goal was to measure quad-specific features such as beam synchronization and focal spot (size, smoothing contrast ratio or irradiation nonuniformity) versus the LMJ requirements. Following the laser commissioning, the LIL has become a major instrument dedicated to the achievement of plasma physics experiments for the French Simulation Program and was also opened to the academic scientific community. One of the attributes of the LIL facility is to be very flexible to accommodate the requests of plasma physicists during campaigns. The LIL is constantly evolving to best meet the needs of target physicists. Changes made or planned are either to improve the quality of laser beams, or to increase the LIL Energy-Power operating space. To optimize preparation and design of shot campaigns, the LIL performance status has been elaborated. It gives information about the characteristics of the laser in terms of near field and far field, defines the steps to maintain performance, explains how the facility responds to the request, details settings (smoothing, shaping of the focal spot, energy, temporal pulse shaping, beam pointing) and gives the limits in energy and power. In this paper, an overview of the LIL performance is presented. (authors)

  11. Status of NESTOR

    International Nuclear Information System (INIS)

    NSC KIPT proposed to construct a new X-ray and soft ultraviolet source NESTOR with a 40 - 225 MeV electron storage ring in Kharkov. NESTOR is a new type radiation source on the base of Compton scattering and a storage ring. Electrons are injected in the storage ring at 100 MeV and ramped up to final energy of 225 MeV. So, using interaction angle 10 deg. and 150 deg., the facility covers operation energy range of radiation from soft ultraviolet trough synchrotron radiation from bending magnets up to hard X-ray radiation through Compton scattering (∼1 eV ∼1 MeV). It is supposed that stored electron beam current will be of about 200 mA. Along with use of Nd:Yag laser of 10 W average power which was developed by High-Q laser firm and optical resonator with accumulation gain of about 1000 it allows to provide X-ray radiation flux up to 1011 phot/s. NESTOR is the cooperative facility and its development is supported by Ukrainian government and NATO SfP project number 977982. It is supposed that NESTOR will be in operation by mid-2007 year. The status of the project and main facility systems are described in the report

  12. Biosimilar drugs: Current status.

    Science.gov (United States)

    Kumar, Rajiv; Singh, Jagjit

    2014-07-01

    Biologic products are being developed over the past three decades. The expiry of patent protection for many biological medicines has led to the development of biosimilars in UK or follow on biologics in USA. This article reviews the literature on biosimilar drugs that covers the therapeutic status and regulatory guidelines. Appraisal of published articles from peer reviewed journals for English language publications, search from PubMed, and guidelines from European Medicines Agency, US Food Drug Administration (FDA) and India were used to identify data for review. Literature suggest that biosimilars are similar biological products, i.e., comparable but not identical to the reference product, are not generic version of innovator product and do not ensure therapeutic equivalence. Biosimilars present more challenges than conventional generics and marketing approval is also more complicated. To improve access, US Congress passed the Biologics Price Competition and Innovation act 2009 and US FDA allowed "abbreviated pathway" for their approval. U.S law has defined new standards and terms and EMA scientific guidelines have also set detailed approval standards. India being one of the most preferred manufacturing destinations of biosimilars, there is a need for stringent safety and regulatory guidelines. The New India Guidelines "Draft Guidelines on Similar Biologics were announced in June 2012, by Department of Biotechnology at Boston bio and available online. PMID:25143877

  13. Nanometals - Status and perspective

    International Nuclear Information System (INIS)

    Nanometals and nanotechnology have over the years been covered in papers, books and conferences - also in many Risoe International Symposia, where the 30th in 2009 dealt solely with nanostructured metals. Since then, rapid progress has been made in synthesis, characterization and modeling, and it is timely to discuss status and perspective also with a view on applications in an international forum such as the Risoe Symposium. Both keynote and contributed papers address important current problems illustrating global research and development in this field. Examples are the development of new synthesis techniques followed by characterization and modeling of microstructures both in 2D and 3D now starting to bridge the micrometer scales. The vital area of mechanical behavior is addressed by the development of new testing techniques and a broad effort to characterize and model mechanical properties of metals strengthened by dislocations and twins. This research has now led to new understanding of both strengthening mechanisms and strengh structure relationships based on experiments in combination with analytical and numerical modeling. The holistic approach to research on nanometals demonstrated by these proceedings can guide both scientists and technologists in their future work also with the aim of introducing into society this new group of advanced materials. Such an effort is important, as science and technology today is significantly affected by politics of governments and international institutions, and therefore a new initiative in the pressent is to include a discussion of research and development in the area of nanometals i USA, China and Japan. (Author)

  14. Nanometals - Status and perspective

    Energy Technology Data Exchange (ETDEWEB)

    Faester, S.; Hansen, N.; Huang, X.; Juul Jensen, D.; Ralph, B. (eds.)

    2012-11-01

    Nanometals and nanotechnology have over the years been covered in papers, books and conferences - also in many Risoe International Symposia, where the 30th in 2009 dealt solely with nanostructured metals. Since then, rapid progress has been made in synthesis, characterization and modeling, and it is timely to discuss status and perspective also with a view on applications in an international forum such as the Risoe Symposium. Both keynote and contributed papers address important current problems illustrating global research and development in this field. Examples are the development of new synthesis techniques followed by characterization and modeling of microstructures both in 2D and 3D now starting to bridge the micrometer scales. The vital area of mechanical behavior is addressed by the development of new testing techniques and a broad effort to characterize and model mechanical properties of metals strengthened by dislocations and twins. This research has now led to new understanding of both strengthening mechanisms and strengh structure relationships based on experiments in combination with analytical and numerical modeling. The holistic approach to research on nanometals demonstrated by these proceedings can guide both scientists and technologists in their future work also with the aim of introducing into society this new group of advanced materials. Such an effort is important, as science and technology today is significantly affected by politics of governments and international institutions, and therefore a new initiative in the pressent is to include a discussion of research and development in the area of nanometals i USA, China and Japan. (Author)

  15. Present Status of Kamland

    Science.gov (United States)

    Inoue, Kunio

    2001-01-01

    The KamLAND experiment can explore world lowest mass difference region of neutrino oscillation parameter with an artificial neutrino source. It observes anti-neutrinos from various power plants spread in Japan with about 175 km baseline. This baseline is two order of magnitude longer than those of previously performed reactor experiments 1,2. This challenging measurement requires very low background environment as low as 10-13 g/g Uranium and Thorium impurities. In order to achieve this very low impurity level, various techniques (detector design, material selection, construction scheme etc) have been invested. These efforts have been rewarded rather quickly and current achievement doesn't hinder even the 7Be solar neutrino observation requiring 10-16 g/g U and Th impurities. Various background sources relevant to the reactor and solar neutrino observation are considered and description of efforts to eliminate those backgrounds are the main issue of this manuscript. Physics goal and current successful construction status are also highlighted.

  16. ImBuild: Impact of building energy efficiency programs

    Energy Technology Data Exchange (ETDEWEB)

    Scott, M.J.; Hostick, D.J.; Belzer, D.B.

    1998-04-01

    As part of measuring the impact of government programs on improving the energy efficiency of the Nation`s building stock, the Department of Energy Office of Building Technology, State and Community Programs (BTS) is interested in assessing the economic impacts of its portfolio of programs, specifically the potential impact on national employment and income. The special-purpose version of the IMPLAN model used in this study is called ImBuild. In comparison with simple economic multiplier approaches, such as Department of Commerce RIMS 2 system, ImBuild allows for more complete and automated analysis of the economic impacts of energy efficiency investments in buildings. ImBuild is also easier to use than existing macroeconomic simulation models. The authors conducted an analysis of three sample BTS energy programs: the residential generator-absorber heat exchange gas heat pump (GAX heat pump), the low power sulfur lamp (LPSL) in residential and commercial applications, and the Building America program. The GAX heat pump would address the market for the high-efficiency residential combined heating and cooling systems. The LPSL would replace some highly efficient fluorescent commercial lighting. Building America seeks to improve the energy efficiency of new factory-built, modular, manufactured, and small-volume, site-built homes through use of systems engineering concepts and early incorporation of new products and processes, and by increasing the demand for more energy-efficient homes. The authors analyze a scenario for market penetration of each of these technologies devised for BTS programs reported in the BTS GPRA Metrics Estimates, FY99 Budget Request, December 19, 1997. 46 figs., 4 tabs.

  17. Straw insulated buildings. Nature building materials; Strohgedaemmte Gebaeude. Naturbaustoffe

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-06-01

    Straw is one of the major agricultural by-products and is mainly used as litter in animal husbandry and to compensate the balance of humus. A relatively recent development is the use of straw bales for the construction of buildings. The brochure under consideration documents the technical development of straw construction in Germany. Possibilities of the use of straw in single family homes up to commercial buildings are described.

  18. Building and Testing with Gradle

    CERN Document Server

    Berglund, Tim

    2011-01-01

    Build and test software written in Java and many other languages with Gradle, the open source project automation tool that's getting a lot of attention. This concise introduction provides numerous code examples to help you explore Gradle, both as a build tool and as a complete solution for automating the compilation, test, and release process of simple and enterprise-level applications. Discover how Gradle improves on the best ideas of Ant, Maven, and other build tools, with standards for developers who want them and lots of flexibility for those who prefer less structure. Use Gradle with Gr

  19. Energy - efficient buildings in pakistan

    International Nuclear Information System (INIS)

    Pakistan is one of the countries with the highest energy consumption for domestic use. Annual energy consumption by the domestic sector is 45.9 % of the total, while the industrial sector, consumes about 27.5%. About half of the total energy consumed is used in buildings and/or heating, ventilation and air-conditioning (HVAC) and lighting appliances. The energy consumed for the same purposes in China and UK is 25 to 30 % and 40 %, respectively, even in extreme weather conditions. Energy deficiency in Pakistan is approximately 5,000 MWe, which results in worst load-shedding in summers and, lately, even in winters. Building new energy sources like dams, coal power plants and renewable energy power projects are some possible solutions, but these are time taking and need at least 2 to 6 years to complete, depending upon the nature of the project. Fast development of energy-efficient buildings is, therefore, necessary to deal with exacerbating energy-crisis and related environmental impact in Pakistan. Innovations in the prevailing building-design will help the country in reducing the energy burden. These innovations may include improved architectural designs, energy-efficient building materials, electrical appliances and implementation of building energy-efficiency codes. In 1987, the National Energy Conservation Centre (ENERCON), was established under Ministry of Environment, Government of Pakistan, with the aim to build awareness among the masses for energy conservation, and to make policies regarding energy-conservation structures in the country. But no policy regarding building energy codes has been introduced by ENERCON till now. In collaboration with Pakistan Engineering Council (PEC), ENERCON has recently finalized the Building Energy Code of Pakistan Energy Provisions 2011 for which statutory notification is under process for necessary amendment in the building by-laws. The implementation of this Energy Code will result in 25 to 30 % of energy savings in the

  20. Building Huys Hengelo in VRML

    OpenAIRE

    Reidsma, D.; Kragtwijk, M.; Nijholt, A.; Bearman, D.; Garzotto, F

    2001-01-01

    In this paper we report about our attempts to rebuild a historical building, ‘Huys Hengelo’, its interior, a farm built next to it and other parts of its environment (including a draw-bridge and a gate) using the Virtual Reality Modeling Language (VRML). This castle building played an important role in the history of its region. The main issues we deal with in this paper are: the unreliability of available sources − forcing us to show alternatives rather than ‘the building as it was’, the pos...

  1. The RHIC status update

    Energy Technology Data Exchange (ETDEWEB)

    Ozaki, S. [Brookhaven National Lab., Upton, NY (United States)

    1995-07-15

    The construction of the Relativistic Heavy Ion Collider (RHIC) began in 1991, with the completion date originally scheduled for 1997. Significant reduction of the funding levels in FY 1993 and 1994, and the funding level cap for FY 1995 and later years caused a 19-month stretchout of the construction period to the second quarter of FY 1999, and an increase of the total estimated cost (TEC) to $475 M. The Project, therefore, is now at the halfway mark of the construction period with actual cost and schedule performance tracking close to the DOE-approved baseline. Construction funding through FY 1994 reached close to 60% of the TEC. Incidentally, if one adds the current value of preexisting facilities which will be incorporated into RHIC, such as the injection system (Tandem Van de Graaff - the Booster - the AGS), the esixting 3.8 km tunnel, the 24 kW helium refrigerator, etc., the total value of the RHIC facility, when completed, will reach one billion dollars, if not more. The accelerator lattice design was finalized in 1992 after an intensive study was made to optimize the collider design for performance, operational flexibility, and value engineering. The civil construciton, including the collider enclosure, magnet access ports to the ring tunnel, and six service buildings for accelerator power supplies and cryogenic control boxes was completed.

  2. AP1000 status overview

    International Nuclear Information System (INIS)

    The AP1000 is a two-loop, 1000 MWe pressurized water reactor (PWR) with passive safety features and extensive plant simplifications to enhance the construction, operation, and maintenance. The AP1000 design is derived directly from the AP600, a two-loop, 600 MWe PWR. The AP600 uses proven technology, which builds on the over 30 years of operating PWR experience. The AP600 design received Final Design Approval from the U.S. NRC in September 1998 and Design Certification in December 1999. The AP600 meets all of the U.S. electric utility requirements including their cost goals. Although the AP600 is the most cost-effective plant ready for deployment, it is still more expensive than the $1000/kw needed to compete in the United States today In order to develop a cost competitive nuclear power plant Westinghouse has completed design studies which demonstrate that it is feasible to increase the power output of the AP600 to at least 1000 MWe, maintaining its current design configuration, use of proven components and licensing basis. In order to achieve these objectives the AP1000 has been designed within the space constraints of the AP600, while retaining the credibility of proven components and substantial safety margins. This paper describes the changes made to up-rate the AP600 and gives an overview of the plant design. It also summarizes the basis for the AP600 testing program and computer codes being sufficient for the AP1000. (authors)

  3. Status of fission power

    International Nuclear Information System (INIS)

    Fission energy is reviewed from the viewpoints of technology, economics, politics, manufacturers, consumers, and foreign countries. Technically, the reactor program is operating and the light water reactor industry shows signs of maturing, although recent business has been disappointing. Marketing of gas-cooled reactors depends, not on technical, but economic and political issues. Liquid metal fast breeder reactors have been demonstrated worldwide, while the gas-cooled fast breeder remains an undemonstrated option. Nuclear plants, currently costing the same as coal plants with scrubbers, are the cheapest option for utilities because most of the cost is imbedded. The defeat of nuclear initiatives in seven states indicates that public feeling is not as anti-nuclear as opponents to nuclear power claim. The harshness of last winter demonstrated the advantages of a power source that is not so sensitive to the weather for reliable operation and transport, as well as low cost energy. Other nations are proceeding to build a nuclear capability, which the U.S. may jeopardize because of concerns about the fuel cycle, nuclear waste disposal, uranium reserves, and nuclear proliferation

  4. Competence building capacity shortage

    International Nuclear Information System (INIS)

    The objective of the project 'Competence Building Capacity Shortage' has been 'to increase knowledge about central approaches aimed at solving the peaking capacity problem in restructured power systems'. With respect to reserve markets, a model was developed in the project to analyze the relations between reserve requirements and prices in the spot and reserve markets respectively. A mathematical model was also developed and implemented, which also includes the balance market, and has a good ability to predict the relations between these markets under various assumptions. With some further development, this model can be used fore realistic analyses of these markets in a Nordic context. It was also concluded that certain system requirements with respect to frequency and time deviation can be relaxed without adverse effects. However, the requirements to system bias, Frequency Activated Operating Reserves and Frequency Activated Contingency Reserves cannot be relaxed, the latter because they must cover the dimensioning fault in the system. On the other hand, Fast Contingency Reserves can be reduced by removing requirements to national balances. Costs can furthermore be reduced by increasingly adapting a Nordic as opposed to national approach. A model for stepwise power flow was developed in the project, which is especially useful to analyze slow power system dynamics. This is relevant when analysing the effects of reserve requirements. A model for the analysis of the capacity balance in Norway and Sweden was also developed. This model is useful for looking at the future balance under various assumptions regarding e.g. weather conditions, demand growth and the development of the generation system. With respect to the present situation, if there is some price flexibility on the demand side and system operators are able to use reserves from the demand side, the probability for load shedding during the peak load hour is close to zero under the weather conditions after

  5. BREEAM [Building Research Establishment Environmental Assessment Method] BRE [Building Research Establishment] assessment method for buildings

    International Nuclear Information System (INIS)

    Buildings account for a large share of environmental impacts in their construction, use, and demolition. In western Europe, buildings account for ca 50% of primary energy use (hence CO2 output), far outweighing the contribution of the transport and industrial sectors. Other impacts from building energy use include the use of chemicals such as chlorofluorocarbons for cooling. In the United Kingdom, the Building Research Establishment (BRE) has developed a certificate system for environmental labelling of buildings so that the performance of the building against a set of defined environmental criteria can be made visible to clients. This system thus rewards positive actions to improve the environmental performance of buildings and assists in marketing to an environmentally aware clientele. Issues included in assessments for awarding the certificate are addressed under three main headings: global issues and use of resources, local issues, and indoor issues. Global issues include ozone depletion and CO2 emissions; local issues include public health and water conservation; and indoor issues include air quality and lighting. 8 refs., 1 tab

  6. Status of solar neutrino experiments

    International Nuclear Information System (INIS)

    A summary of the status of four solar neutrino experiments is presented. The Homestake 37Cl data are presented and the possible time dependence of the data is addressed. Data from 1040 days of operation of the Kamiokande II detector are presented next. The status of the 71Ga experiment in the Baksan Neutrino Observatory, which has operated for a short time, is discussed. The summary concludes with a discussion of the status of the Sudbury Neutrino Observatory, which has been under construction since the beginning of 1990. 7 refs., 6 figs

  7. Web Links on Sustainable Buildings

    OpenAIRE

    Hui, Sam CM

    2005-01-01

    This web site is developed with the aim to promote sustainable design and planning of buildings. Key information is collected from various sources and organised in a systematic way for efficient study and exploration of the subjects.

  8. 224-T TRUSAF Building upgrade

    International Nuclear Information System (INIS)

    This study considers the upgrades that would be necessary to extend the life of the Transuranic Waste Storage and Assay Facility (TRUSAF) for an additional 30 years. The study also considers cleanup and conversion of the canyon area of the building for storage of solid waste. The 224-T Building was constructed in the 1940s to support process operations of the T-Plant. The function of the facility has changed over the years, and at present the northern half of the building is used to store solid waste. This portion of the building is referred to as the TRUSAF. TRUSAF is one of only two onsite facilities licensed to receive and store solid TRU wastes. Original intentions were for TRUSAF to be used for TRU solid waste storage until the WRAP 1 Facility became operational

  9. 324 Building Baseline Radiological Characterization

    Energy Technology Data Exchange (ETDEWEB)

    R.J. Reeder, J.C. Cooper

    2010-06-24

    This report documents the analysis of radiological data collected as part of the characterization study performed in 1998. The study was performed to create a baseline of the radiological conditions in the 324 Building.

  10. Rise of the build infrastructure

    International Nuclear Information System (INIS)

    CMS Offline Software, CMSSW, is an extremely large software project, with roughly 3 millions lines of code, two hundreds of active developers and two to three active development branches. Given the scale of the problem, both from a technical and a human point of view, being able to keep on track such a large project, bug free, and to deliver builds for different architectures is a challenge in itself. Moreover the challenges posed by the future migration of CMSSW to multithreading also require adapting and improving our QA tools. We present the work done in the last two years in our build and integration infrastructure, particularly in the form of improvements to our build tools, in the simplification and extensibility of our build infrastructure and the new features added to our QA and profiling tools. Finally we present our plans for the future directions for code management and how this reflects on our workflows and the underlying software infrastructure.

  11. Understanding Net Zero Energy Buildings

    DEFF Research Database (Denmark)

    Salom, Jaume; Widén, Joakim; Candanedo, José;

    2011-01-01

    Although several alternative definitions exist, a Net-Zero Energy Building (Net ZEB) can be succinctly described as a grid-connected building that generates as much energy as it uses over a year. The “net-zero” balance is attained by applying energy conservation and efficiency measures and by...... incorporating renewable energy systems. While based on annual balances, a complete description of a Net ZEB requires examining the system at smaller time-scales. This assessment should address: (a) the relationship between power generation and building loads and (b) the resulting interaction with the power grid....... This paper presents and categorizes quantitative indicators suitable to describe both aspects of the building’s performance. These indicators, named LMGI - Load Matching and Grid Interaction indicators, are easily quantifiable and could complement the output variables of existing building simulation...

  12. LCG/AA build infrastructure

    International Nuclear Information System (INIS)

    The Software Process and Infrastructure (SPI) project provides a build infrastructure for regular integration testing and release of the LCG Applications Area software stack. In the past, regular builds have been provided using a system which has been constantly growing to include more features like server-client communication, long-term build history and a summary web interface using present-day web technologies. However, the ad-hoc style of software development resulted in a setup that is hard to monitor, inflexible and difficult to expand. The new version of the infrastructure is based on the Django Python framework, which allows for a structured and modular design, facilitating later additions. Transparency in the workflows and ease of monitoring has been one of the priorities in the design. Formerly missing functionality like on-demand builds or release triggering will support the transition to a more agile development process.

  13. CONVERGING REDUNDANT SENSOR NETWORK INFORMATION FOR IMPROVED BUILDING CONTROL

    Energy Technology Data Exchange (ETDEWEB)

    Dale K. Tiller; Gregor P. Henze

    2004-11-01

    Knowing how many people occupy a building, and where they are located, is a key component of building energy management and security. Commercial, industrial and residential buildings often incorporate systems used to determine occupancy, however, current sensor technology and control algorithms limit the effectiveness of both energy management and security systems. This topical report describes results from the first phase of a project to design, implement, validate, and prototype new technologies to monitor occupancy, control indoor environment services, and promote security in buildings. Phase I of the project focused on instrumentation and data collection. In this project phase a new occupancy detection system was developed, commissioned and installed in a sample of private offices and open-plan office workstations. Data acquisition systems were developed and deployed to collect data on space occupancy profiles. Analysis tools based on Bayesian probability theory were applied to the occupancy data generated by the sensor network. The inference of primary importance is a probability distribution over the number of occupants and their locations in a building, given past and present sensor measurements. Inferences were computed for occupancy and its temporal persistence in individual offices as well as the persistence of sensor status. The raw sensor data were also used to calibrate the sensor belief network, including the occupancy transition matrix used in the Markov model, sensor sensitivity, and sensor failure models. This study shows that the belief network framework can be applied to the analysis of data streams from sensor networks, offering significant benefits to building operation compared to current practice.

  14. Status of funded actions

    International Nuclear Information System (INIS)

    The GEDEPEON status workshop is organised to review the GEDEPEON research actions, which have been funded in 2003. Presentations are made by research teams actively involved in GEDEPEON research areas. Speakers were invited to show how the presented research data are related to the general goals of transmutation, for which 2006 is an important milestone, and innovative systems. This document gathers 18 presentations (slides) among the 32 given at this workshop and dealing with: 1 - nuclear data: measurement of cross-sections of neutron induced reactions at the nTof time of flight facilities of CERN and of Gelina at Geel (F. Gunsing), study of (n,xn) reactions thanks to prompt gamma spectroscopy (M. Kerveno), iodine 129 cross-sections (G. Noguere); 2 - reactor physics/cycles: CEA-CNRS scenarios (F. Varaine, D. Heuer), analysis of uncertainties and sensitivity factors of nuclear data on innovative systems (molten-salt reactors) (A. Bidaud); 3 - materials: contribution to the study of T91 steel fatigue by lead-bismuth (D. Gorse), kinetics and mechanisms of fatigue by liquid metals (V. Laporte), studies of molten salts corrosion in future reactors (S. Sanchez), stress-induced fatigue by liquid metal (A. Verleene), thermodynamic study of the Bi-Fe-Hg-O-Pb quinary system (A. Maitre), synchrotron imaging study of fatigue by liquid metals (D. Bellet); 4 - future systems: molten salts reprocessing strategy - impact on the molten salt reactors neutronics (L. Mathieu), microscopy technique for the characterization of the thermal properties of inert materials for gas-cooled reactors (L. David), modeling and application of sub-atomic phenomena (J. Maillard), forecasting of the chemical compatibility between fissile compounds and inert materials in future high temperature reactors using a thermodynamical approach (A. Maitre), hydrogen production by thermochemical cycles (S. Colette), development of Ni-W refractory alloys for high temperature and molten salts reactors (J

  15. Status Report on PERC

    International Nuclear Information System (INIS)

    Full text: Important open questions of particle physics and cosmology can be addressed with precision measurements in neutron beta decay. Main emphasis lies on the search for evidence of possible extensions to the Standard Model and searches for new symmetry concepts. In general, these measurements are complementary to direct searches in high-energy physics. Observables in neutron decay are abundant: Besides the neutron lifetime, angular correlations involving the neutron spin as well as momenta and spins of the emitted particles are characterized by individual coefficients. These coefficients can be related to the underlying coupling strengths of the weak interaction, including yet unobserved ones. Each coefficient in turn relates to an underlying broken symmetry. With the new facility PERC (http://www.physi.uni-heidelberg.de/Forschung/ANP/PERC/collaboration.php) several symmetry tests based on neutron decay data become accessible. PERC (Proton Electron Radiation Channel) is a novel source of neutron decay products: these are collected by a strong longitudinal magnetic eld of 1.5 T directly from inside a neutron guide. This combination provides highest phase space density of decay products. A magnetic mirror of up to 6 T serves to perform precise cuts in phase space, reducing related systematic errors. Altogether, the sensitivity of neutron decay studies will be improved by one order of magnitude. The new beam station PERC is currently under development by an international collaboration and will be installed at the FRM II in Garching, Germany. Besides the physics motivation, the concept, sensitivity, applications, and status of PERC are presented in this talk. (author)

  16. Building digital collections: An evaluation

    Digital Repository Service at National Institute of Oceanography (India)

    Tapaswi, M.P.

    resources of long-term value and therefore have to be maintained forever. The commitment of an organisation to maintain the collection is of paramount importance. This is backed up by financial and technical support. Organisations give way to dynamic... wonderful collection of Indian biodiversity information building about 80,000 records disappeared the moment the individual left the organisation. BUILDING DIGITAL COLLECTIONS 11 Normally, projects start with financial support from external agencies. However...

  17. Building America House Simulation Protocols

    Energy Technology Data Exchange (ETDEWEB)

    Hendron, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States); Engebrecht, Cheryn [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2010-09-01

    The House Simulation Protocol document was developed to track and manage progress toward Building America's multi-year, average whole-building energy reduction research goals for new construction and existing homes, using a consistent analytical reference point. This report summarizes the guidelines for developing and reporting these analytical results in a consistent and meaningful manner for all home energy uses using standard operating conditions.

  18. Modeling as Theory-Building

    OpenAIRE

    Schwaninger, Markus; Grösser, Stefan N.

    2008-01-01

    The purpose of this contribution is to make the idea of modeling as theory-building operational. We conceive the modeling process as a theory-building process, thereby opening up a new perspective on the methodology of modeling in the social sciences. By reconceptualizing the notion of modeling, we hope to convey the advantages of more conceptual thinking in management. Practitioners could gain effectiveness in dealing with external complexity if they would espouse the modeling task as a disc...

  19. A Novel Tetrathiafulvalene Building Block

    DEFF Research Database (Denmark)

    Jeppesen, Jan Oskar; Takimiya, Kazuo; Thorup, Niels;

    1999-01-01

    Efficient synthesis of a novel tetrathiafulvalene building block. 2,3-bis(2-cyanoethylthio)-6,7-bis(thiocyanato-methyl)tetrathiafulv alene (7) useful for stepwise and asymmetrical bis-function-alization is reported.......Efficient synthesis of a novel tetrathiafulvalene building block. 2,3-bis(2-cyanoethylthio)-6,7-bis(thiocyanato-methyl)tetrathiafulv alene (7) useful for stepwise and asymmetrical bis-function-alization is reported....

  20. Renovation work at Building 280

    CERN Multimedia

    EN Department

    2010-01-01

    Processing units and containers will be temporarily installed in front of Building 280 between 17 and 21 February 2010 while renovation work is carried out on electrical equipment. During this period, the Route FERMI, i.e. the area between Buildings 280 and 530, will be closed to traffic. You are requested to comply with the road signs in place. Thank you for your understanding. For further information, please call 160481. EN-EL Group

  1. Build Autonomic Agents with ABLE

    Institute of Scientific and Technical Information of China (English)

    吴吉义

    2007-01-01

    The IBM Agent Building and Learning Environment(ABLE) provides a lightweight Java~(TM) agent frame- work,a comprehensive JavaBeansTM library of intelligent software components,a set of development and test tools, and an agent platform.After the introduction to ABLE,classes and interfaces in the ABLE agent framework were put forward.At last an autonomic agent that is an ABLE-based architecture for incrementally building autonomic systems was discussed.

  2. Building a Chinatown From Scratch

    Institute of Scientific and Technical Information of China (English)

    Li Zhijian

    2011-01-01

    ON Ahmadou Ahidjo Street in Douala, the economic capital of Cameroon,there are several buildings bearing Chinese names like Da Shanghai (Great Shanghai) and Zhong Ka Youyilou (Sino-Cameroon Friendship Building).This is Cameroon's Chinatown.Here,passersby flock to the Great China Hotel and the Great China Market.Located at the edge of the neighborhood,both are owned by one man:Hu Xiaomeng.

  3. A Guide to Building Commissioning

    Energy Technology Data Exchange (ETDEWEB)

    Baechler, Michael C.

    2011-09-01

    Commissioning is the process of verifying that a building's heating, ventilation, and air conditioning (HVAC) and lighting systems perform correctly and efficiently. Without commissioning, system and equipment problems can result in higher than necessary utility bills and unexpected and costly equipment repairs. This report reviews the benefits of commissioning, why it is a requirement for Leadership in Energy and Environmental Design (LEED) certification, and why building codes are gradually adopting commissioning activities into code.

  4. Dust and the Sick Building Syndrome

    DEFF Research Database (Denmark)

    Gyntelberg, Finn; Suadicani, Poul; Wohlfahrt Nielsen, Jan; Skov, Peder; Valbjørn, Ole; Nielsen, Peter A.; Schneider, Thomas; Jørgensen, Ole; Wolkoff, Peder; Wilkins, C. K.; Gravesen, Suzanne; Norn, Svend

    Farmakologi, bacteria, dust, histamine, disease, gram-negative, indoor climate, sick building syndrome......Farmakologi, bacteria, dust, histamine, disease, gram-negative, indoor climate, sick building syndrome...

  5. The Status of Implementation on Additional Protocol at KAERI

    International Nuclear Information System (INIS)

    Under the Additional Protocol, a State is required to provide the IAEA with further information on nuclear related activities, all buildings on a site, etc. through an expanded declaration and further access rights at a nuclear site and any location included in the expanded declaration. This paper describes the implementation status on the expanded declaration and the complementary access at KAERI under the AP. This paper reviewed the implementation status of the AP at KAERI, and there are some practical issues to prepare the expanded declarations as mentioned above. From the view point of the effective and efficient processing of the expanded declaration, it will be necessary to discuss the criterion for the definition of the nuclear fuel cycle-related R and D to be declared under the AP with IAEA

  6. Wynkoop Building Performance Measurement: Water

    Energy Technology Data Exchange (ETDEWEB)

    Fowler, Kimberly M.; Kora, Angela R.

    2012-08-26

    This report is a summary of the water analysis performance for the Denver, Colorado Wynkoop Building. The Wynkoop Building (Figure 1) was built in 2006 as the Environmental Protection Agency (EPA) Region 8 Headquarters intended to house over 900 occupants in the 301,292 gross square feet (248,849 rentable square feet). The building was built on a brownfield in the Lower Downtown Historic District as part of an urban redevelopment effort. The building was designed and constructed through a public-private partnership with the sustainable design elements developed jointly by General Services Administration (GSA) and EPA. That partnership is still active with all parties still engaged to optimize building operations and use the building as a Learning Laboratory. The building design achieved U.S. Green Building Council Leadership in Energy and Environmental Design for New Construction (LEED-NC) Gold Certification in 2008 (Figure 2) and a 2008 EPA Energy Star Rating of 96 with design highlights that include: (1) Water use was designed to use 40% less than a typical design baseline. The design included low flow fixtures, waterless urinals and dual flush toilets; (2) Native and adaptive vegetation were selected to minimize the need for irrigation water for landscaping; and (3) Energy use intensity was modeled at 66.1 kBtus/gross square foot, which is 39% better than ASHRAE 90.1 1999. The Wynkoop Building water use (10 gallons/square foot) was measured at lower than industry average (15 gallons/square foot) and GSA goals (13 gallons/square foot), however, it was higher than building management expected it would be. The type of occupants and number of occupants can have a significant impact on fixture water use. The occupancy per floor varied significantly over the study time period, which added uncertainty to the data analysis. Investigation of the fixture use on the 2nd, 5th, and 7th floors identified potential for water use reduction if the flush direction of the dual

  7. Refugee status determination: three challenges

    Directory of Open Access Journals (Sweden)

    Martin Jones

    2009-04-01

    Full Text Available Refugee status determination (RSD, which is vital to the protection of so many asylum seekers worldwide, is at best an imperfect, haphazard and challenging process. It merits greater attention and appropriate reform.

  8. Status of Fermilab E-710

    International Nuclear Information System (INIS)

    This report give the current status of E-710, an experiment at the Fermilab bar pp Tevatron Collider to measure elastic scattering, total cross sections and diffraction dissociation up to √s = 1.8 TeV

  9. Experimental status of quantum electrodynamics

    International Nuclear Information System (INIS)

    This review of the experimental status of quantum electrodynamics covers the fine structure constant, the muon g-2 value, the Lamb shift in hydrogen, the finite proton radius, progress in muonium, and positronium. 37 references

  10. Outcome of Refractory Status Epilepticus

    Directory of Open Access Journals (Sweden)

    J Gordon Millichap

    2002-01-01

    Full Text Available The records of twenty-two children, ages 4.5 months to 18 years, treated for refractory status epilepticus (RSE between 1992 and 2000, were reviewed retrospectively at Children’s Hospital, Boston.

  11. Radiological Characterization and Final Facility Status Report Tritium Research Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, T.B.; Gorman, T.P.

    1996-08-01

    This document contains the specific radiological characterization information on Building 968, the Tritium Research Laboratory (TRL) Complex and Facility. We performed the characterization as outlined in its Radiological Characterization Plan. The Radiological Characterization and Final Facility Status Report (RC&FFSR) provides historic background information on each laboratory within the TRL complex as related to its original and present radiological condition. Along with the work outlined in the Radiological Characterization Plan (RCP), we performed a Radiological Soils Characterization, Radiological and Chemical Characterization of the Waste Water Hold-up System including all drains, and a Radiological Characterization of the Building 968 roof ventilation system. These characterizations will provide the basis for the Sandia National Laboratory, California (SNL/CA) Site Termination Survey .Plan, when appropriate.

  12. Status of ASTRID architecture and pre-conceptual design

    International Nuclear Information System (INIS)

    In the frame of the June 2006 French act on sustainable management of radioactive materials and wastes, the ASTRID (Advanced Sodium Technological Reactor for Industrial Demonstration) reactor aims to demonstrate, from the 2020’s, at the industrial scale, improvements in the identified fields of progress of Sodium-cooled Fast Reactor (safety, operability, economy) and to perform transmutation demonstration. CEA (French Commission for Atomic Energy and Alternative Energy) is the leader of the ASTRID project, including ten industrial partnerships and EDF SEPTEN for architectural engineering design support. This document presents the status of the ASTRID pre-conceptual and global industrial design. All of the options of processing systems studied by the industrial engineering partners are managed in configuration models, and monitored by a CEA ASTRID project management team. Items addressed in this document include views of nuclear island buildings, other operational and process buildings, projected site layout with requirements and specific constraints (external hazards like earthquake, floods, airplanes crashes…). (author)

  13. Recovery Act. Advanced Load Identification and Management for Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Yi [Eaton Corporation, Menomonee Falls, WI (United States); Casey, Patrick [Eaton Corporation, Menomonee Falls, WI (United States); Du, Liang [Eaton Corporation, Menomonee Falls, WI (United States); He, Dawei [Eaton Corporation, Menomonee Falls, WI (United States)

    2014-02-12

    In response to the U.S. Department of Energy (DoE)’s goal of achieving market ready, net-zero energy residential and commercial buildings by 2020 and 2025, Eaton partnered with the Department of Energy’s National Renewable Energy Laboratory (NREL) and Georgia Institute of Technology to develop an intelligent load identification and management technology enabled by a novel “smart power strip” to provide critical intelligence and information to improve the capability and functionality of building load analysis and building power management systems. Buildings account for 41% of the energy consumption in the United States, significantly more than either transportation or industrial. Within the building sector, plug loads account for a significant portion of energy consumption. Plug load consumes 15-20% of building energy on average. As building managers implement aggressive energy conservation measures, the proportion of plug load energy can increase to as much as 50% of building energy leaving plug loads as the largest remaining single source of energy consumption. This project focused on addressing plug-in load control and management to further improve building energy efficiency accomplished through effective load identification. The execution of the project falls into the following three major aspects; An intelligent load modeling, identification and prediction technology was developed to automatically determine the type, energy consumption, power quality, operation status and performance status of plug-in loads, using electric waveforms at a power outlet level. This project demonstrated the effectiveness of the developed technology through a large set of plug-in loads measurements and testing; A novel “Smart Power Strip (SPS) / Receptacle” prototype was developed to act as a vehicle to demonstrate the feasibility of load identification technology as a low-cost, embedded solution; and Market environment for plug-in load control and management solutions

  14. The bivariate current status model

    OpenAIRE

    Groeneboom, P.

    2013-01-01

    For the univariate current status and, more generally, the interval censoring model, distribution theory has been developed for the maximum likelihood estimator (MLE) and smoothed maximum likelihood estimator (SMLE) of the unknown distribution function, see, e.g., [12], [7], [4], [5], [6], [10], [11] and [8]. For the bivariate current status and interval censoring models distribution theory of this type is still absent and even the rate at which we can expect reasonable estimators to converge...

  15. Maximum demand power control system design status of PEFP

    Energy Technology Data Exchange (ETDEWEB)

    Mun, Kyeong Jun; Jung, Hoi Won; Park, Sung Sik; Song, In Teak; Kim, Jun Yeon [KAERI, Daejeon (Korea, Republic of)

    2012-10-15

    The purpose of maximum demand power control system is to not exceed the limit of the maximum demand pre defined. To limit the maximum demand, non critical loads are controlled or disconnected when the limit is about to be exceeded. Maximum demand power generally occurs during summer; especially cooling period in each building (from 10 am to 4 pm). At this period, possible electric load should be controlled or disconnected to save electric energy while not affect the main processes. In this paper, we described maximum demand power control system designed status of PEFP.

  16. Maximum demand power control system design status of PEFP

    International Nuclear Information System (INIS)

    The purpose of maximum demand power control system is to not exceed the limit of the maximum demand pre defined. To limit the maximum demand, non critical loads are controlled or disconnected when the limit is about to be exceeded. Maximum demand power generally occurs during summer; especially cooling period in each building (from 10 am to 4 pm). At this period, possible electric load should be controlled or disconnected to save electric energy while not affect the main processes. In this paper, we described maximum demand power control system designed status of PEFP

  17. Status report on the FEL program at RRCAT

    International Nuclear Information System (INIS)

    We are building a Compact Ultrafast TErahertz Free Electron Laser (CUTE-FEL) that can provide radiation from 50 to 100 μm, with a peak power of the order of 0.5 MW and average power of 0.5 W. Some sub-systems of the CUTE-FEL have already been developed and tested while some others are in an advanced stage of commissioning/fabrication/procurement. In this paper, we will review the status of activity on various fronts and discuss our preparations for commissioning of the FEL in near future. (author)

  18. Sentinel-2 Mission status

    Science.gov (United States)

    Hoersch, Bianca; Colin, Olivier; Gascon, Ferran; Arino, Olivier; Spoto, Francois; Marchese, Franco; Krassenburg, Mike; Koetz, Benjamin

    2016-04-01

    Copernicus is a joint initiative of the European Commission (EC) and the European Space Agency (ESA), designed to establish a European capacity for the provision and use of operational monitoring information for environment and security applications. Within the Copernicus programme, ESA is responsible for the development of the Space Component, a fully operational space-based capability to supply earth-observation data to sustain environmental information Services in Europe. The Sentinel missions are Copernicus dedicated Earth Observation missions composing the essential elements of the Space Component. In the global Copernicus framework, they are complemented by other satellites made available by third-parties or by ESA and coordinated in the synergistic system through the Copernicus Data-Access system versus the Copernicus Services. The Copernicus Sentinel-2 mission provides continuity to services relying on multi-spectral high-resolution optical observations over global terrestrial surfaces. Sentinel-2 capitalizes on the technology and the vast experience acquired in Europe and the US to sustain the operational supply of data for services such as forest monitoring, land cover changes detection or natural disasters management. The Sentinel-2 mission offers an unprecedented combination of the following capabilities: ○ Systematic global coverage of land surfaces: from 56°South to 84°North, coastal waters and Mediterranean sea; ○ High revisit: every 5 days at equator under the same viewing conditions with 2 satellites; ○ High spatial resolution: 10m, 20m and 60m; ○ Multi-spectral information with 13 bands in the visible, near infra-red and short wave infra-red part of the spectrum; ○ Wide field of view: 290 km. The data from the Sentinel-2 mission are available openly and freely for all users with online easy access since December 2015. The presentation will give a status report on the Sentinel-2 mission, and outlook for the remaining ramp-up Phase, the

  19. CHARIS Construction Status, Design, and Future Science

    Science.gov (United States)

    Groff, Tyler Dean; Kasdin, N. Jeremy; Peters, Mary Anne; Galvin, Michael; Knapp, Gillian R.; Brandt, Timothy; Loomis, Craig; Carr, Michael; Mede, Kyle; Jarosik, Norman; McElwain, Michael W.; Guyon, Olivier; Jovanovic, Nemanja; Takato, Naruhisa; Hayashi, Masahiko

    2015-01-01

    Princeton University is funded by the National Astronomical Observatory of Japan to build an integral field spectrograph (IFS) dubbed the Coronagraphic High Angular Resolution Imaging Spectrograph (CHARIS). CHARIS is part of the ongoing exoplanet science effort at the Subaru Telescope, and will serve as the science imager for the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) and AO188 systems. The principal science goals are disk imaging and high contrast spectra of brown dwarfs and hot Jovian planets across J, H, and K bands. SCExAO is a coronagraphic and wavefront control system that will be capable of extreme adaptive optics and quasi-static speckle suppression. Speckle suppression is meant to reduce the residual speckle to a level that makes it possible to detect planets at very low inner working angles (~80 mas). Even so, CHARIS must mitigate spectral contamination from the residual speckle halo due to crosstalk between the closely packed spectra of the image. CHARIS mitigates crosstalk via an array of field stops behind the lenslet array and carefully toleranced relay optics. This reduces uncertainty in the measured spectrum of the exoplanets by increasing robustness of the spectrograph to nearby bright speckles. Mitigating crosstalk in hardware both improves science and reduces computational overhead. Combined with a detailed wavefront budget this improves the utility of CHARIS in the speckle control loop. Another defining feature of CHARIS is its disperser design. In addition to imaging in individual J, H, and K bands, CHARIS has a fourth mode that images across all three simultaneously. This required an improvement in the linearity of dispersion from 1.15 to 2.38 microns. To do so the CHARIS project has chosen a new high-index dispersing material and characterized its properties at cryogenic temperatures. We present the build status of the spectrograph, including status and viability of operating an H2RG detector directly using a SAM card via

  20. Mobile augmented reality in support of building damage and safety assessment

    Science.gov (United States)

    Kim, W.; Kerle, N.; Gerke, M.

    2016-02-01

    Rapid and accurate assessment of the state of buildings in the aftermath of a disaster event is critical for an effective and timely response. For rapid damage assessment of buildings, the utility of remote sensing (RS) technology has been widely researched, with focus on a range of platforms and sensors. However, RS-based approaches still have limitations to assess structural integrity and the specific damage status of individual buildings. Structural integrity refers to the ability of a building to hold the entire structure. Consequently, ground-based assessment conducted by structural engineers and first responders is still required. This paper demonstrates the concept of mobile augmented reality (mAR) to improve performance of building damage and safety assessment in situ. Mobile AR provides a means to superimpose various types of reference or pre-disaster information (virtual data) on actual post-disaster building data (real buildings). To adopt mobile AR, this study defines a conceptual framework based on the level of complexity (LOC). The framework consists of four LOCs, and for each of these, the data types, required processing steps, AR implementation and use for damage assessment are described. Based on this conceptualization we demonstrate prototypes of mAR for both indoor and outdoor purposes. Finally, we conduct a user evaluation of the prototypes to validate the mAR approach for building damage and safety assessment.