WorldWideScience

Sample records for broadband slab selection

  1. Broadband high reflectivity in subwavelength-grating slab waveguides.

    Science.gov (United States)

    Tian, Hao; Cui, Xuan; Du, Yan; Tan, Peng; Shi, Guang; Zhou, Zhongxiang

    2015-10-19

    We computationally study a subwavelength dielectric grating structure, show that slab waveguide modes can be used to obtain broadband high reflectivity, and analyze how slab waveguide modes influence reflection. A structure showing interference between Fabry-Perot modes, slab waveguide modes, and waveguide array modes is designed with ultra-broadband high reflectivity. Owing to the coupling of guided modes, the region with reflectivity R > 0.99 has an ultra-high bandwidth (Δf / ̅f > 30%). The incident-angle region with R > 0.99 extends over a range greater than 40°. Moreover, an asymmetric waveguide structure with a semiconductor substrate is studied.

  2. Silicon nanocrystal-based photonic crystal slabs with broadband and efficient directional light emission

    Czech Academy of Sciences Publication Activity Database

    Ondič, Lukáš; Varga, Marián; Pelant, Ivan; Valenta, J.; Kromka, Alexander; Elliman, R. G.

    2017-01-01

    Roč. 7, č. 1 (2017), s. 1-8, č. článku 5763. ISSN 2045-2322 R&D Projects: GA ČR GJ16-09692Y; GA MŠk(CZ) LD15003 Institutional support: RVO:68378271 Keywords : photonic crystal slab * silicon nanocrystals * light emission Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 4.259, year: 2016

  3. Silicon nanocrystal-based photonic crystal slabs with broadband and efficient directional light emission.

    Science.gov (United States)

    Ondič, L; Varga, M; Pelant, I; Valenta, J; Kromka, A; Elliman, R G

    2017-07-18

    Light extraction from a thin planar layer can be increased by introducing a two-dimensional periodic pattern on its surface. This structure, the so-called photonic crystal (PhC) slab, then not only enhances the extraction efficiency of light but can direct the extracted emission into desired angles. Careful design of the structures is important in order to have a spectral overlap of the emission with extraction (leaky) modes. We show that by fabricating PhC slabs with optimized dimensions from silicon nanocrystals (SiNCs) active layers, the extraction efficiency of vertical light emission from SiNCs at a particular wavelength can be enhanced ∼ 11 times compared to that of uncorrugated SiNCs-rich layer. More importantly, increased light emission can be obtained in a broad spectral range and, simultaneously, the extracted light can stay confined within relatively narrow angle around the normal to the sample plane. We demonstrate experimentally and theoretically that the physical origin of the enhancement is such that light originating from SiNCs first couples to leaky modes of the PhCs and is then efficiently extracted into the surrounding.

  4. Non-contrast-enhanced pulmonary vein MRI with a spatially selective slab inversion preparation sequence.

    Science.gov (United States)

    Hu, Peng; Chuang, Michael L; Kissinger, Kraig V; Goddu, Beth; Goepfert, Lois A; Rofsky, Neil M; Manning, Warren J; Nezafat, Reza

    2010-02-01

    We propose a non-contrast-enhanced, three-dimensional, free-breathing, electrocardiogram-gated, gradient recalled echo sequence with a slab-selective inversion for pulmonary vein (PV) MRI. A sagittal inversion slab was applied prior to data acquisition to suppress structures adjacent to the left atrium (LA) and PVs, thereby improving the conspicuity of the PV and LA. Compared with other MR angiography methods using an inversion pulse, the proposed method does not require signal subtraction and the inversion slab is not parallel to the imaging slab. The feasibility of the proposed method was demonstrated in healthy subjects. The inversion slab thickness and inversion time were optimized to be 60 mm and 500 ms, respectively. Compared to conventional gradient recalled echo imaging without inversion, the proposed technique significantly increased the contrast-to-noise ratios between the LA and the right atrium by 20-fold (P slab (P > 0.3). The proposed technique greatly enhances the conspicuity of the PVs and LA without significant loss of signal-to-noise ratio.

  5. A novel broadband bi-mode active frequency selective surface

    Science.gov (United States)

    Xu, Yang; Gao, Jinsong; Xu, Nianxi; Shan, Dongzhi; Song, Naitao

    2017-05-01

    A novel broadband bi-mode active frequency selective surface (AFSS) is presented in this paper. The proposed structure is composed of a periodic array of convoluted square patches and Jerusalem Crosses. According to simulation results, the frequency response of AFSS definitely exhibits a mode switch feature between band-pass and band-stop modes when the diodes stay in ON and OFF states. In order to apply a uniform bias to each PIN diode, an ingenious biasing network based on the extension of Wheatstone bridge is adopted in prototype AFSS. The test results are in good agreement with the simulation results. A further physical mechanism of the bi-mode AFSS is shown by contrasting the distribution of electric field on the AFSS patterns for the two working states.

  6. A novel broadband bi-mode active frequency selective surface

    Directory of Open Access Journals (Sweden)

    Yang Xu

    2017-05-01

    Full Text Available A novel broadband bi-mode active frequency selective surface (AFSS is presented in this paper. The proposed structure is composed of a periodic array of convoluted square patches and Jerusalem Crosses. According to simulation results, the frequency response of AFSS definitely exhibits a mode switch feature between band-pass and band-stop modes when the diodes stay in ON and OFF states. In order to apply a uniform bias to each PIN diode, an ingenious biasing network based on the extension of Wheatstone bridge is adopted in prototype AFSS. The test results are in good agreement with the simulation results. A further physical mechanism of the bi-mode AFSS is shown by contrasting the distribution of electric field on the AFSS patterns for the two working states.

  7. Broadband Reflectionless Metasheets: Frequency-Selective Transmission and Perfect Absorption

    Directory of Open Access Journals (Sweden)

    V. S. Asadchy

    2015-07-01

    Full Text Available Energy of propagating electromagnetic waves can be fully absorbed in a thin lossy layer, but only in a narrow frequency band, as follows from the causality principle. On the other hand, it appears that there are no fundamental limitations on broadband matching of thin resonant absorbing layers. However, known thin absorbers produce significant reflections outside of the resonant absorption band. In this paper, we explore possibilities to realize a thin absorbing layer that produces no reflected waves in a very wide frequency range, while the transmission coefficient has a narrow peak of full absorption. Here we show, both theoretically and experimentally, that a thin resonant absorber, invisible in reflection in a very wide frequency range, can be realized if one and the same resonant mode of the absorbing array unit cells is utilized to create both electric and magnetic responses. We test this concept using chiral particles in each unit cell, arranged in a periodic planar racemic array, utilizing chirality coupling in each unit cell but compensating the field coupling at the macroscopic level. We prove that the concept and the proposed realization approach also can be used to create nonreflecting layers for full control of transmitted fields. Our results can have a broad range of potential applications over the entire electromagnetic spectrum including, for example, perfect ultracompact wave filters and selective multifrequency sensors.

  8. Broadband photonic crystal fiber coupler with polarization selection of coupling ratio

    Science.gov (United States)

    Jaroszewicz, Leszek R.; Stasiewicz, Karol A.; Marć, Paweł; Szymański, Michał

    2010-09-01

    In the paper a new broadband photonic crystal fiber coupler is presented. The proper application of the biconical taper technology has been used for manufacturing the coupler without air holes collapse in LMA10 fiber (NKT Photonics Crystal). This coupler, operates in the weakly coupling condition, protects coupling operation in range from 900 nm to 1700 nm. The coupling ratio between output arms is depending on wavelength and can be tuning by selection the proper input state of polarization. It gives opportunity to use the broadband crystal fiber coupler in many applications in which it is necessary to tune a coupling between output arms during the measurement.

  9. Preliminary performance analysis of a transverse flow spectrally selective two-slab packed bed volumetric receiver

    CSIR Research Space (South Africa)

    Roos, TH

    2016-05-01

    Full Text Available to the incident radiation (transverse flow). The gap between the window and slab 1 has been removed, so the bed is held in place by the sidewalls, the floor and the window, allowing arbitrary orientation and dispensing with the need for beam-down operation...

  10. Reduction of B1 sensitivity in selective single-slab 3D turbo spin echo imaging with very long echo trains.

    Science.gov (United States)

    Park, Jaeseok; Mugler, John P; Hughes, Timothy

    2009-10-01

    Single-slab 3D turbo/fast spin echo (SE) imaging with very long echo trains was recently introduced with slab selection using a highly selective excitation pulse and short, nonselective refocusing pulses with variable flip angles for high imaging efficiency. This technique, however, is vulnerable to image degradation in the presence of spatially varying B(1) amplitudes. In this work we develop a B(1) inhomogeneity-reduced version of single-slab 3D turbo/fast SE imaging based on the hypothesis that it is critical to achieve spatially uniform excitation. Slab selection was performed using composite adiabatic selective excitation wherein magnetization is tipped into the transverse plane by a nonselective adiabatic-half-passage pulse and then slab is selected by a pair of selective adiabatic-full-passage pulses. Simulations and experiments were performed to evaluate the proposed technique and demonstrated that this approach is a simple and efficient way to reduce B(1) sensitivity in single-slab 3D turbo/fast SE imaging with very long echo trains. (c) 2009 Wiley-Liss, Inc.

  11. Slab track

    OpenAIRE

    Golob, Tina

    2014-01-01

    The last 160 years has been mostly used conventional track with ballasted bed, sleepers and steel rail. Ensuring the high speed rail traffic, increasing railway track capacities, providing comfortable and safe ride as well as high reliability and availability railway track, has led to development of innovative systems for railway track. The so-called slab track was first built in 1972 and since then, they have developed many different slab track systems around the world. Slab track was also b...

  12. A novel tunable frequency selective surface absorber with dual-DOF for broadband applications.

    Science.gov (United States)

    Kong, Peng; Yu, XiaoWei; Liu, ZhengYang; Zhou, Kai; He, Yun; Miao, Ling; Jiang, JianJun

    2014-12-01

    A novel tunable frequency selective surface (FSS) with dual-degrees of freedom (DOF) is presented, and firstly applied to broadband absorber. Based on a simple prototype unit cell resonator, an approach for achieving multi-resonances is studied. A unit cell pattern with gradient edges is discussed, and variable resistor and variable capacitor are introduced to fully utilize its characteristic of multi-resonances. Bias line is designed to provide bias voltage respectively for two variable devices and provide two operational DOF for FSS. Simulation and measurement results both show that the tunable FSS absorber with dual-DOF has wideband absorption with the reflectivity below -10 dB in 1-5 GHz and with a total thickness of about 10 mm.

  13. Broadband Access

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Broadband Access. Worldwide market for broadband access $30 Billion! Over 200 million broadband subscribers worldwide! Various Competing Broadband access. Digital Subscriber line; Wireless; Optical Fiber.

  14. A SUCCESSFUL BROADBAND SURVEY FOR GIANT Ly{alpha} NEBULAE. I. SURVEY DESIGN AND CANDIDATE SELECTION

    Energy Technology Data Exchange (ETDEWEB)

    Prescott, Moire K. M. [Department of Physics, Broida Hall, Mail Code 9530, University of California, Santa Barbara, CA 93106 (United States); Dey, Arjun; Jannuzi, Buell T., E-mail: mkpresco@physics.ucsb.edu [National Optical Astronomy Observatory, 950 North Cherry Avenue, Tucson, AZ 85719 (United States)

    2012-04-01

    Giant Ly{alpha} nebulae (or Ly{alpha} 'blobs') are likely sites of ongoing massive galaxy formation, but the rarity of these powerful sources has made it difficult to form a coherent picture of their properties, ionization mechanisms, and space density. Systematic narrowband Ly{alpha} nebula surveys are ongoing, but the small redshift range covered and the observational expense limit the comoving volume that can be probed by even the largest of these surveys and pose a significant problem when searching for such rare sources. We have developed a systematic search technique designed to find large Ly{alpha} nebulae at 2 {approx}< z {approx}< 3 within deep broadband imaging and have carried out a survey of the 9.4 deg{sup 2} NOAO Deep Wide-Field Survey Booetes field. With a total survey comoving volume of Almost-Equal-To 10{sup 8} h{sup -3}{sub 70} Mpc{sup 3}, this is the largest volume survey for Ly{alpha} nebulae ever undertaken. In this first paper in the series, we present the details of the survey design and a systematically selected sample of 79 candidates, which includes one previously discovered Ly{alpha} nebula.

  15. Development of Flat Slab – Column Interaction with Different Thickness

    Directory of Open Access Journals (Sweden)

    Binti Joohari Ilya

    2017-01-01

    Full Text Available Flat slab – column connection has received much attention in recent years due to its simplicity of construction where beam is not required to support the slab. Flat slab has many usages in the construction field and has been investigated as a potential building material. Despite its many benefits, flat slab is easily subjected to punching shear failure. A simple approach to minimize punching shear failure is by increasing the slab thickness. It is generally accepted that the performance of flat slab is improved by using shear reinforcement; however, little attention has been paid to the selection of thickness. This research focuses on the crack behaviour of flat slab due to different slab thickness. Two specimens with different slab thickness have been constructed and tested to obtain the flat slab strength and crack pattern behaviour. Increasing the slab thickness was found to improve the strength of the flat slab and minimize the deflection and crack appearance on the slab.

  16. Piezo-Phototronic Effect on Selective Electron or Hole Transport through Depletion Region of Vis-NIR Broadband Photodiode.

    Science.gov (United States)

    Zou, Haiyang; Li, Xiaogan; Peng, Wenbo; Wu, Wenzhuo; Yu, Ruomeng; Wu, Changsheng; Ding, Wenbo; Hu, Fei; Liu, Ruiyuan; Zi, Yunlong; Wang, Zhong Lin

    2017-08-01

    Silicon underpins nearly all microelectronics today and will continue to do so for some decades to come. However, for silicon photonics, the indirect band gap of silicon and lack of adjustability severely limit its use in applications such as broadband photodiodes. Here, a high-performance p-Si/n-ZnO broadband photodiode working in a wide wavelength range from visible to near-infrared light with high sensitivity, fast response, and good stability is reported. The absorption of near-infrared wavelength light is significantly enhanced due to the nanostructured/textured top surface. The general performance of the broadband photodiodes can be further improved by the piezo-phototronic effect. The enhancement of responsivity can reach a maximum of 78% to 442 nm illumination, the linearity and saturation limit to 1060 nm light are also significantly increased by applying external strains. The photodiode is illuminated with different wavelength lights to selectively choose the photogenerated charge carriers (either electrons or holes) passing through the depletion region, to investigate the piezo-phototronic effect on electron or hole transport separately for the first time. This is essential for studying the basic principles in order to develop a full understanding about piezotronics and it also enables the development of the better performance of optoelectronics. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Slab reformer

    Science.gov (United States)

    Spurrier, Francis R. (Inventor); DeZubay, Egon A. (Inventor); Murray, Alexander P. (Inventor); Vidt, Edward J. (Inventor)

    1985-01-01

    Slab-shaped high efficiency catalytic reformer configurations particularly useful for generation of fuels to be used in fuel cell based generation systems. A plurality of structures forming a generally rectangular peripheral envelope are spaced about one another to form annular regions, an interior annular region containing a catalytic bed and being regeneratively heated on one side by a hot combustion gas and on the other side by the gaseous products of the reformation. An integrally mounted combustor is cooled by impingement of incoming oxidant.

  18. Slab reformer

    Science.gov (United States)

    Spurrier, Francis R.; DeZubay, Egon A.; Murray, Alexander P.; Vidt, Edward J.

    1984-02-07

    Slab-shaped high efficiency catalytic reformer configurations particularly useful for generation of fuels to be used in fuel cell based generation systems. A plurality of structures forming a generally rectangular peripheral envelope are spaced about one another to form annular regions, an interior annular region containing a catalytic bed and being regeneratively heated on one side by a hot comubstion gas and on the other side by the gaseous products of the reformation. An integrally mounted combustor is cooled by impingement of incoming oxidant.

  19. Photon transport in thin disordered slabs

    Indian Academy of Sciences (India)

    We examine using Monte Carlo simulations, photon transport in optically `thin' slabs whose thickness is only a few times the transport mean free path *, with particles of different scattering anisotropies. The confined geometry causes an auto-selection of only photons with looping paths to remain within the slab.

  20. Highly doped semiconductor plasmonic nanoantenna arrays for polarization selective broadband surface-enhanced infrared absorption spectroscopy of vanillin

    Science.gov (United States)

    Barho, Franziska B.; Gonzalez-Posada, Fernando; Milla, Maria-Jose; Bomers, Mario; Cerutti, Laurent; Tournié, Eric; Taliercio, Thierry

    2017-11-01

    Tailored plasmonic nanoantennas are needed for diverse applications, among those sensing. Surface-enhanced infrared absorption (SEIRA) spectroscopy using adapted nanoantenna substrates is an efficient technique for the selective detection of molecules by their vibrational spectra, even in small quantity. Highly doped semiconductors have been proposed as innovative materials for plasmonics, especially for more flexibility concerning the targeted spectral range. Here, we report on rectangular-shaped, highly Si-doped InAsSb nanoantennas sustaining polarization switchable longitudinal and transverse plasmonic resonances in the mid-infrared. For small array periodicities, the highest reflectance intensity is obtained. Large periodicities can be used to combine localized surface plasmon resonances (SPR) with array resonances, as shown in electromagnetic calculations. The nanoantenna arrays can be efficiently used for broadband SEIRA spectroscopy, exploiting the spectral overlap between the large longitudinal or transverse plasmonic resonances and narrow infrared active absorption features of an analyte molecule. We demonstrate an increase of the vibrational line intensity up to a factor of 5.7 of infrared-active absorption features of vanillin in the fingerprint spectral region, yielding enhancement factors of three to four orders of magnitude. Moreover, an optimized readout for SPR sensing is proposed based on slightly overlapping longitudinal and transverse localized SPR.

  1. Highly doped semiconductor plasmonic nanoantenna arrays for polarization selective broadband surface-enhanced infrared absorption spectroscopy of vanillin

    Directory of Open Access Journals (Sweden)

    Barho Franziska B.

    2017-11-01

    Full Text Available Tailored plasmonic nanoantennas are needed for diverse applications, among those sensing. Surface-enhanced infrared absorption (SEIRA spectroscopy using adapted nanoantenna substrates is an efficient technique for the selective detection of molecules by their vibrational spectra, even in small quantity. Highly doped semiconductors have been proposed as innovative materials for plasmonics, especially for more flexibility concerning the targeted spectral range. Here, we report on rectangular-shaped, highly Si-doped InAsSb nanoantennas sustaining polarization switchable longitudinal and transverse plasmonic resonances in the mid-infrared. For small array periodicities, the highest reflectance intensity is obtained. Large periodicities can be used to combine localized surface plasmon resonances (SPR with array resonances, as shown in electromagnetic calculations. The nanoantenna arrays can be efficiently used for broadband SEIRA spectroscopy, exploiting the spectral overlap between the large longitudinal or transverse plasmonic resonances and narrow infrared active absorption features of an analyte molecule. We demonstrate an increase of the vibrational line intensity up to a factor of 5.7 of infrared-active absorption features of vanillin in the fingerprint spectral region, yielding enhancement factors of three to four orders of magnitude. Moreover, an optimized readout for SPR sensing is proposed based on slightly overlapping longitudinal and transverse localized SPR.

  2. Extreme Emission Line Galaxies in CANDELS: Broad-Band Selected, Star-Bursting Dwarf Galaxies at Z greater than 1

    Science.gov (United States)

    vanderWel, A.; Straughn, A. N.; Rix, H.-W.; Finkelstein, S. L.; Koekemoer, A. M.; Weiner, B. J.; Wuyts, S.; Bell, E. F.; Faber, S. M.; Trump, J. R.; hide

    2012-01-01

    We identify an abundant population of extreme emission line galaxies (EELGs) at redshift z approx. 1.7 in the Cosmic Assembly Near-IR Deep Extragalactic Legacy Survey (CANDELS) imaging from Hubble Space Telescope/Wide Field Camera 3 (HST/WFC3). 69 EELG candidates are selected by the large contribution of exceptionally bright emission lines to their near-infrared broad-band magnitudes. Supported by spectroscopic confirmation of strong [OIII] emission lines . with rest-frame equivalent widths approx. 1000A in the four candidates that have HST/WFC3 grism observations, we conclude that these objects are galaxies with approx.10(exp 8) Solar Mass in stellar mass, undergoing an enormous starburst phase with M*/M* of only approx. 15 Myr. These bursts may cause outflows that are strong enough to produce cored dark matter profiles in low-mass galaxies. The individual star formation rates and the co-moving number density (3.7x10(exp -4) Mpc(sup -3) can produce in approx.4 Gyr much of the stellar mass density that is presently contained in 10(exp 8) - 10(exp 9) Solar Mass dwarf galaxies. Therefore, our observations provide a strong indication that many or even most of the stars in present-day dwarf galaxies formed in strong, short-lived bursts, mostly at z > 1.

  3. Broad-band characteristics of seven new hard X-ray selected cataclysmic variables

    Science.gov (United States)

    Bernardini, F.; de Martino, D.; Mukai, K.; Russell, D. M.; Falanga, M.; Masetti, N.; Ferrigno, C.; Israel, G.

    2017-10-01

    We present timing and spectral analysis of a sample of seven hard X-ray selected cataclysmic variable candidates based on simultaneous X-ray and optical observations collected with XMM-Newton, complemented with Swift/BAT and INTEGRAL /IBIS hard X-ray data and ground-based optical photometry. For six sources, X-ray pulsations are detected for the first time in the range of ˜296-6098 s, identifying them as members of the magnetic class. Swift J0927.7-6945, Swift J0958.0-4208, Swift J1701.3-4304, Swift J2113.5+5422 and possibly PBC J0801.2-4625 are intermediate polars (IPs), while Swift J0706.8+0325 is a short (1.7 h) orbital period polar, the 11th hard X-ray-selected identified so far. X-ray orbital modulation is also observed in Swift J0927.7-6945 (5.2 h) and Swift J2113.5+5422 (4.1 h). Swift J1701.3-4304 is discovered as the longest orbital period (12.8 h) deep eclipsing IP. The spectra of the magnetic systems reveal optically thin multitemperature emission between 0.2 and 60 keV. Energy-dependent spin pulses and the orbital modulation in Swift J0927.7-6945 and Swift J2113.5+5422 are due to intervening local high-density absorbing material (NH ˜ 1022 - 23 cm-2). In Swift J0958.0-4208 and Swift J1701.3-4304, a soft X-ray blackbody (kT ˜ 50 and ˜80 eV) is detected, adding them to the growing group of `soft' IPs. White dwarf masses are determined in the range of ˜ 0.58-1.18 M⊙, indicating massive accreting primaries in five of them. Most sources accrete at rates lower than the expected secular value for their orbital period. Formerly proposed as a long-period (9.4 h) nova-like CV, Swift J0746.3-1608 shows peculiar spectrum and light curves suggesting either an atypical low-luminosity CV or a low-mass X-ray binary.

  4. A SUCCESSFUL BROADBAND SURVEY FOR GIANT Lyα NEBULAE. I. SURVEY DESIGN AND CANDIDATE SELECTION

    International Nuclear Information System (INIS)

    Prescott, Moire K. M.; Dey, Arjun; Jannuzi, Buell T.

    2012-01-01

    Giant Lyα nebulae (or Lyα 'blobs') are likely sites of ongoing massive galaxy formation, but the rarity of these powerful sources has made it difficult to form a coherent picture of their properties, ionization mechanisms, and space density. Systematic narrowband Lyα nebula surveys are ongoing, but the small redshift range covered and the observational expense limit the comoving volume that can be probed by even the largest of these surveys and pose a significant problem when searching for such rare sources. We have developed a systematic search technique designed to find large Lyα nebulae at 2 ∼ 2 NOAO Deep Wide-Field Survey Boötes field. With a total survey comoving volume of ≈10 8 h –3 70 Mpc 3 , this is the largest volume survey for Lyα nebulae ever undertaken. In this first paper in the series, we present the details of the survey design and a systematically selected sample of 79 candidates, which includes one previously discovered Lyα nebula.

  5. Broadband non-selective excitation of plutonium isotopes for isotope ratio measurements in resonance ionization mass spectrometry: a theoretical study.

    Science.gov (United States)

    Sankari, M

    2012-10-15

    Making isotope ratio measurements with minimum isotope bias has always been a challenging task to mass spectrometrists, especially for the specific case of plutonium, owing to the strategic importance of the element. In order to use resonance ionization mass spectrometry (RIMS) as a tool for isotope ratio measurements, optimization of the various laser parameters and other atomic and system parameters is critical to minimize isotopic biases. Broadband simultaneous non-selective excitation of the isotopes of plutonium in the triple resonance excitation scheme with λ(1) = 420.77 nm, λ(2) = 847.28 nm, and λ(3) = 767.53 nm based on density matrix formalism has been theoretically computed for the determination of isotope ratios. The effects of the various laser parameters and other factors such as the atomization temperature and the dimensions of the atomic beam on the estimation of isotope ratios were studied. The effects of Doppler broadening, and time-dependent excitation parameters such as Rabi frequencies, ionization rate and the effect of non-Lorenztian lineshape have all been incorporated. The average laser powers and bandwidths for the three-excitation steps were evaluated for non-selective excitation. The laser intensity required to saturate the three-excitation steps were studied. The two-dimensional lineshape contour and its features were investigated, while the reversal of peak asymmetry of two-step and two-photon excitation peaks under these conditions is discussed. Optimized powers for the non-selective ionization of the three transitions were calculated as 545 mW, 150 mW and 545 mW and the laser bandwidth for all the three steps was ~20 GHz. The isotopic bias between the resonant and off-resonant isotope under the optimized conditions was no more than 9%, which is better than an earlier reported value. These optimized laser power and bandwidth conditions are better than in the earlier experimental work since these comprehensive calculations yield

  6. Broadband Mm-Wave OFDM Communications in Doubly Selective Channel: Performance Evaluation Using Measured Mm-Wave Channel

    DEFF Research Database (Denmark)

    Chen, Xiaoming; Fan, Wei; Pedersen, Gert F.

    2018-01-01

    coefficients of the broadband mm-wave channel do not follow Gaussian distribution due to the broad bandwidth. It is also shown that, given a cyclic prefix (CP) length for a certain delay spread, an effective PN mitigation scheme enables a PN corrupted OFDM system to function with small subcarrier spacing and...

  7. Broadband Mm-Wave OFDM Communications in Doubly Selective Channel: Performance Evaluation Using Measured Mm-Wave Channel

    DEFF Research Database (Denmark)

    Chen, Xiaoming; Fan, Wei; Pedersen, Gert F.

    2018-01-01

    coefficients of the broadband mm-wave channel do not follow Gaussian distribution due to the broad bandwidth. It is also shown that, given a cyclic prefix (CP) length for a certain delay spread, an effective PN mitigation scheme enables a PN corrupted OFDM system to function with small subcarrier spacing and......In this work, we evaluate the performance of the broadband millimeter-wave (mm-wave) OFDM system in the presence of phase noise (PN) of phase-locked loop based oscillator and delay spread of measured mm-wave channel. It is shown, using Akaike's information criterion, that the channel tap......, therefore, small CP overhead, with only slight degradation of the error rate performance....

  8. Alternate approach slab reinforcement.

    Science.gov (United States)

    2010-06-01

    The upper mat of reinforcing steel, in exposed concrete bridge approach slabs, is prone to corrosion damage. Chlorides applied to the highways : for winter maintenance can penetrate this concrete layer. Eventually chlorides reach the steel and begin ...

  9. Slab replacement maturity guidelines.

    Science.gov (United States)

    2014-04-01

    This study investigated the use of maturity method to determine early age strength of concrete in slab : replacement application. Specific objectives were (1) to evaluate effects of various factors on the compressive : maturity-strength relationship ...

  10. Slab Leaf Bowls

    Science.gov (United States)

    Suitor, Cheryl

    2012-01-01

    In science class, fourth graders investigate the structure of plants and leaves from trees and how the process of photosynthesis turns sunlight into sugar proteins. In this article, the author fuses art and science for a creative and successful clay slab project in her elementary art classroom. (Contains 1 online resource.)

  11. Reliability of Plastic Slabs

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle

    1989-01-01

    In the paper it is shown how upper and lower bounds for the reliability of plastic slabs can be determined. For the fundamental case it is shown that optimal bounds of a deterministic and a stochastic analysis are obtained on the basis of the same failure mechanisms and the same stress fields....

  12. Photon transport in thin disordered slabs

    Indian Academy of Sciences (India)

    ... auto-selection of only photons with looping paths to remain within the slab. The results of the Monte Carlo simulations are borne out by our analytical treatment that incorporates directional persistence by the use of the Ornstein–Uhlenbeck process, which interpolates between the short time ballistic and long time diffusive ...

  13. Adoption of Broadband Services

    DEFF Research Database (Denmark)

    Falch, Morten

    2008-01-01

    Broadband is seen as a key infrastructure for developing the information society. For this reason many Governments are actively engaged in stimulating investments in broadband infrastructures and use of broadband services. This chapter compares a wide range of broadband strategies in the most...... successful markets for broadband. This is done through analysis of national policies in three European countries-Denmark, Sweden, and Germany-and the U.S., Japan, and South Korea. We concluded that successful implementation of broadband depends on the kind of policy measures to be taken at the national level...

  14. Punching strength of reinforced concrete flat slabs without shear reinforcement

    Directory of Open Access Journals (Sweden)

    P. V. P. Sacramento

    Full Text Available Punching strength is a critical point in the design of flat slabs and due to the lack of a theoretical method capable of explaining this phenomenon, empirical formulations presented by codes of practice are still the most used method to check the bearing capacity of slab-column connections. This paper discusses relevant aspects of the development of flat slabs, the factors that influence the punching resistance of slabs without shear reinforcement and makes comparisons between the experimental results organized in a database with 74 slabs carefully selected with theoretical results using the recommendations of ACI 318, EUROCODE 2 and NBR 6118 and also through the Critical Shear Crack Theory, presented by Muttoni (2008 and incorporated the new fib Model Code (2010.

  15. Three-dimensional MRI with independent slab excitation and encoding.

    Science.gov (United States)

    Eissa, Amir; Wilman, Alan H

    2012-02-01

    Three-dimensional MRI is typically performed with the same orientation for radiofrequency slab excitation and slab select phase encoding. We introduce independent slab excitation and encoding to create a new degree of freedom in three-dimensional MRI, which is the angular relationship between the prescribed excitation volume and the voxel encoding grid. By separating the directions of slab excitation and slab phase encoding, the independent slab excitation and encoding method allows choice of optimal voxel orientation, while maintaining volume excitation based on anatomic landmarks. The method requires simple pulse sequence modifications and uses standard image reconstruction followed by removal of aliasing and image reformatting. The independent slab excitation and encoding method enables arbitrary oblique angle imaging using fixed voxel encoding gradients to maintain similar eddy current, concomitant field, or magnetic dipole effects independent of the oblique angle of excitation. We apply independent slab excitation and encoding to phase and susceptibility-weighted imaging using fixed voxel encoding aligned with the main magnetic field to demonstrate its value in both standardizing and improving image contrast, when using arbitrary oblique imaging volumes. Copyright © 2011 Wiley Periodicals, Inc.

  16. Investigation of Effect of Slab Opening Location to the Shear Stress

    Directory of Open Access Journals (Sweden)

    Burak Yön

    2010-01-01

    Full Text Available In this study, it is investigated the effect of slab opening location in reinforced concrete building to the structural behavior. For investigation of slab irregularity, three multi storey irregular structures that have different slab opening locations in structure plans and one regular structure are designed. Linear dynamic analyses are performed for the structure models using Time History Analysis method. 13 March 1992 Erzincan Earthquake acceleration records are used for these analyses. It is assumed that slabs of selected structures are modeled as elastic diaphragm. SAP2000 Structural Analysis Program is used in the analyses. Values of slab that near space shear stress obtained from dynamic analyses of selected structures are comparatively evaluated. According to analyses results, it is determined that location of slab opening of structures reasonably both affects the behavior of structures and occurs great slab shear stress.

  17. A cryogenic slab CO laser

    International Nuclear Information System (INIS)

    Ionin, Andrei A; Kozlov, A Yu; Seleznev, L V; Sinitsyn, D V

    2009-01-01

    A compact capacitive transverse RF-discharge-pumped slab CO laser with cryogenically cooled electrodes, which operates both in the cw and repetitively pulsed regimes, is fabricated. The laser operation is studied in the free running multifrequency regime at the vibrational - rotational transitions of the fundamental (V + 1 → V) vibrational bands of the CO molecule in the spectral region from 5.1 to 5.4 μm. Optimal operation conditions (gas mixture composition and pressure, RF pump parameters) are determined. It is shown that only gas mixtures with a high content of oxygen (up to 20% with respect to the concentration of CO molecules) can be used as an active medium of this laser. It is demonstrated that repetitively pulsed pumping is more efficient compared to cw pumping. In this case, quasi-cw lasing regime can be obtained. The maximum average output power of ∼12 W was obtained for this laser operating on fundamental bands and its efficiency achieved ∼14 %. The frequency-selective operation regime of the slab RF-discharge-pumped CO laser was realised at ∼ 100 laser lines in the spectral region from 5.0 to 6.5 μm with the average output power of up to several tens of milliwatts in each line. Lasing at the transitions of the first vibrational overtone (V + 2 → V) of the CO molecule is obtained in the spectral region from 2.5 to 3.9 μm. The average output power of the overtone laser achieved 0.3 W. All the results were obtained without the forced gas mixture exchange in the discharge chamber. Under fixed experimental conditions, repetitively pulsed lasing (with fluctuations of the output characteristics no more than ±10 %) was stable for more than an hour. (lasers)

  18. THE CHANDRA MULTI-WAVELENGTH PROJECT: OPTICAL SPECTROSCOPY AND THE BROADBAND SPECTRAL ENERGY DISTRIBUTIONS OF X-RAY-SELECTED AGNs

    Energy Technology Data Exchange (ETDEWEB)

    Trichas, Markos; Green, Paul J.; Aldcroft, Tom; Kim, Dong-Woo; Mossman, Amy [Harvard-Smithsonian Center for Astrophysics, Cambridge, MA 02138 (United States); Silverman, John D. [Institute for the Physics and Mathematics of the Universe (IPMU), University of Tokyo, Kashiwanoha 5-1-5, Kashiwa-shi, Chiba 277-8568 (Japan); Barkhouse, Wayne [Department of Physics and Astrophysics, University of North Dakota, Grand Forks, ND 58202 (United States); Cameron, Robert A. [W. W. Hansen Experimental Physics Laboratory, Kavli Institute for Particle Astrophysics and Cosmology, Department of Physics and SLAC National Accelerator Laboratory, Stanford University, Stanford, CA 94305 (United States); Constantin, Anca [Department of Physics and Astronomy, James Madison University, PHCH, Harrisonburg, VA 22807 (United States); Ellison, Sara L. [Department of Physics and Astronomy, University of Victoria, Victoria, BC V8P 1A1 (Canada); Foltz, Craig [Division of Astronomical Sciences, National Science Foundation, 4201 Wilson Blvd., Arlington, VA 22230 (United States); Haggard, Daryl [Center for Interdisciplinary Exploration and Research in Astrophysics, Northwestern University, 2145 Sheridan Road, Evanston, IL 60208 (United States); Jannuzi, Buell T. [NOAO, Kitt Peak National Observatory, Tucson, AZ 85726 (United States); Marshall, Herman L. [Kavli Institute for Astrophysics and Space Research, Massachusetts Institute of Technology, 77 Massachusetts Ave., Cambridge, MA 02139 (United States); Perez, Laura M. [Department of Astronomy, California Institute of Technology, 1200 East California Blvd, Pasadena, CA 91125 (United States); Romero-Colmenero, Encarni [South African Astronomical Observatory, P.O. Box 9, Observatory, 7935 (South Africa); Ruiz, Angel [Osservatorio Astronomico di Brera-INAF, Milan (Italy); Smith, Malcolm G., E-mail: mtrichas@cfa.harvard.edu [Cerro Tololo Interamerican Observatory, La Serena (Chile); and others

    2012-06-01

    activity. We have tested the hypothesis that there should be a strong connection between X-ray obscuration and star formation but we do not find any association between X-ray column density and star formation rate both in the general population or the star-forming X-ray Seyferts. Our large compilation also allows us to report here the identification of 81 X-ray Bright Optically inactive Galaxies, 78 z > 3 X-ray sources, and eight Type-2 QSO candidates. Also, we have identified the highest redshift (z = 5.4135) X-ray-selected QSO with optical spectroscopy.

  19. Long-life slab replacement concrete.

    Science.gov (United States)

    2015-03-01

    This research was initiated following reports of high incidence of cracking on FDOT concrete pavement replacement : slab projects. Field slabs were instrumented for data acquisition from high-early-strength concrete pavement : replacement slabs place...

  20. Broadband EM Performance Characteristics of Single Square Loop FSS Embedded Monolithic Radome

    Directory of Open Access Journals (Sweden)

    Raveendranath U. Nair

    2013-01-01

    Full Text Available A monolithic half-wave radome panel, centrally loaded with aperture-type single square loop frequency selective surface (SSL-FSS, is proposed here for broadband airborne radome applications. Equivalent transmission line method in conjunction with equivalent circuit model (ECM is used for modeling the SSL-FSS embedded monolithic half-wave radome panel and evaluating radome performance parameters. The design parameters of the SSL-FSS are optimized at different angles of incidence such that the new radome wall configuration offers superior EM performance from L-band to X-band as compared to the conventional monolithic half-wave slab of identical material and thickness. The superior EM performance of SSL-FSS embedded monolithic radome wall makes it suitable for the design of normal incidence and streamlined airborne radomes.

  1. SUB-SLAB PROBE INSTALLATION

    Science.gov (United States)

    Sub-slab sampling has become an integral part of vapor intrusion investigations. It is now recommended in guidance documents developed by EPA and most states. A method for sub-slab probe installation was devised in 2002, presented at conferences through 2005, and finally docume...

  2. Topological susceptibility from slabs

    Energy Technology Data Exchange (ETDEWEB)

    Bietenholz, Wolfgang [Instituto de Ciencias Nucleares, Universidad Nacional Autónoma de México, A.P. 70-543, Distrito Federal, C.P. 04510 (Mexico); Forcrand, Philippe de [Institute for Theoretical Physics, ETH Zürich,CH-8093 Zürich (Switzerland); CERN, Physics Department, TH Unit, CH-1211 Geneva 23 (Switzerland); Gerber, Urs [Instituto de Ciencias Nucleares, Universidad Nacional Autónoma de México, A.P. 70-543, Distrito Federal, C.P. 04510 (Mexico); Instituto de Física y Matemáticas, Universidad Michoacana de San Nicolás de Hidalgo,Edificio C-3, Apdo. Postal 2-82, Morelia, Michoacán, C.P. 58040 (Mexico)

    2015-12-14

    In quantum field theories with topological sectors, a non-perturbative quantity of interest is the topological susceptibility χ{sub t}. In principle it seems straightforward to measure χ{sub t} by means of Monte Carlo simulations. However, for local update algorithms and fine lattice spacings, this tends to be difficult, since the Monte Carlo history rarely changes the topological sector. Here we test a method to measure χ{sub t} even if data from only one sector are available. It is based on the topological charges in sub-volumes, which we denote as slabs. Assuming a Gaussian distribution of these charges, this method enables the evaluation of χ{sub t}, as we demonstrate with numerical results for non-linear σ-models.

  3. Topological Susceptibility from Slabs

    CERN Document Server

    Bietenholz, Wolfgang; Gerber, Urs

    2015-01-01

    In quantum field theories with topological sectors, a non-perturbative quantity of interest is the topological susceptibility chi_t. In principle it seems straightforward to measure chi_t by means of Monte Carlo simulations. However, for local update algorithms and fine lattice spacings, this tends to be difficult, since the Monte Carlo history rarely changes the topological sector. Here we test a method to measure chi_t even if data from only one sector are available. It is based on the topological charges in sub-volumes, which we denote as slabs. Assuming a Gaussian distribution of these charges, this method enables the evaluation of chi_t, as we demonstrate with numerical results for non-linear sigma-models.

  4. Broadband Faraday Isolator

    OpenAIRE

    Berent, Michal; Rangelov, Andon A.; Vitanov, Nikolay V.

    2012-01-01

    Driving on an analogy with the technique of composite pulses in quantum physics, we propose a broadband Faraday rotator and thus a broadband optical isolator, which is composed of sequences of ordinary Faraday rotators and achromatic quarter-wave plates rotated at the predetermined angles.

  5. Broadband Faraday isolator.

    Science.gov (United States)

    Berent, Michał; Rangelov, Andon A; Vitanov, Nikolay V

    2013-01-01

    Driving on an analogy with the technique of composite pulses in quantum physics, we theoretically propose a broadband Faraday rotator and thus a broadband optical isolator, which is composed of sequences of ordinary Faraday rotators and achromatic quarter-wave plates rotated at the predetermined angles.

  6. Deceased Slabs Drive Oil

    Science.gov (United States)

    Stein, H. J.; Hannah, J. L.

    2017-12-01

    The application of Re-Os isotope geochemistry to dating single oils is a nascent field [1,2]. Challenges include dissection of oils into asphaltene-maltene (ASPH-MALT) components in a way that preserves meaningful chronologic and source information. Significantly, oil-water mixing rapidly transfers Os to the oil, while Re exchange is sluggish [3]. The Os initial ratio of the oil is shifted in the direction of Os carried in the aqueous fluid, whereas the Re-Os isotopic age is preserved. We show that this phenomenon is operative in natural systems. Further, we show that deserpentinization of old oceanic slabs [4], may be linked to expulsion of Os-enriched waters into overlying sedimentary sections - a process that may be of fundamental importance for oil generation. This conclusion does not diminish the role of traditional organic-rich shales as source rocks for the hydrocarbon, but shows that external fluids are essential to petroleum generation. Moreover, the external fluids may be an important driver for expulsion and migration of oils. We have taken apart several petroleum systems from source rock, to residual oil, to tar mat development, to in situ live oil, through to produced oil. In many cases, a fluid with low 187Os/188Os - unlike that of normal basinal brines - provides a critical component to the oil-water mixture. Funding - CHRONOS project supported by Norwegian petroleum industry (Eni-Norge, Lundin, Aker BP) Acknowledgement - Christine Fichler [4], who first queried us on old slabs and oil, and stimulated ideas. [1] Georgiev, S.V., Stein, H.J., Hannah, J.L., Galimberti, R., Nali, M., Yang, G., and Zimmerman, A. (2016) Re-Os dating of maltenes and asphaltenes within single samples of crude oil: Geochim. Cosmochim. Acta 179: 53-75. [doi.org/10.1016/j.gca.2016.01.016] [2] DiMarzio, J., Georgiev, S.V., Stein, H.J., and Hannah, J.L. (in press) Residency of rhenium and osmium in a heavy crude oil: Geochim. Cosmochim. Acta. [3] Hurtig, N.C., Georgiev, S

  7. Slab replacement maturity guidelines : [summary].

    Science.gov (United States)

    2014-04-01

    Concrete sets in hours at moderate temperatures, : but the bonds that make concrete strong continue : to mature over days to years. However, for : replacement concrete slabs on highways, it is : crucial that concrete develop enough strength : within ...

  8. New Packaging for Amplifier Slabs

    Energy Technology Data Exchange (ETDEWEB)

    Riley, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Thorsness, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Suratwala, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Steele, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Rogowski, G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-03-18

    The following memo provides a discussion and detailed procedure for a new finished amplifier slab shipping and storage container. The new package is designed to maintain an environment of <5% RH to minimize weathering.

  9. Strong Plate, Weak Slab Dichotomy

    Science.gov (United States)

    Petersen, R. I.; Stegman, D. R.; Tackley, P.

    2015-12-01

    Models of mantle convection on Earth produce styles of convection that are not observed on Earth.Moreover non-Earth-like modes, such as two-sided downwellings, are the de facto mode of convection in such models.To recreate Earth style subduction, i.e. one-sided asymmetric recycling of the lithosphere, proper treatment of the plates and plate interface are required. Previous work has identified several model features that promote subduction. A free surface or pseudo-free surface and a layer of material with a relatively low strength material (weak crust) allow downgoing plates to bend and slide past overriding without creating undue stress at the plate interface. (Crameri, et al. 2012, GRL)A low viscosity mantle wedge, possibly a result of slab dehydration, decouples the plates in the system. (Gerya et al. 2007, Geo)Plates must be composed of material which, in the case of the overriding plate, are is strong enough to resist bending stresses imposed by the subducting plate and yet, as in the case of the subducting plate, be weak enough to bend and subduct when pulled by the already subducted slab. (Petersen et al. 2015, PEPI) Though strong surface plates are required for subduction such plates may present a problem when they encounter the lower mantle.As the subducting slab approaches the higher viscosity, lower mantle stresses are imposed on the tip.Strong slabs transmit this stress to the surface.There the stress field at the plate interface is modified and potentially modifies the style of convection. In addition to modifying the stress at the plate interface, the strength of the slab affects the morphology of the slab at the base of the upper mantle. (Stegman, et al 2010, Tectonophysics)Slabs that maintain a sufficient portion of their strength after being bent require high stresses to unbend or otherwise change their shape.On the other hand slabs that are weakened though the bending process are more amenable to changes in morphology. We present the results of

  10. Broadband Electromagnetic Technology

    Science.gov (United States)

    2011-06-23

    The objectives of this project are to continue the enhancements to the combined Broadband Electromagnetic and Full Encirclement Unit (BEM-FEU) technologies and to evaluate the systems capability in the laboratory and the field. The BEM instrument ...

  11. Broadband Radiometric LED Measurements.

    Science.gov (United States)

    Eppeldauer, G P; Cooksey, C C; Yoon, H W; Hanssen, L M; Podobedov, V B; Vest, R E; Arp, U; Miller, C C

    2016-01-01

    At present, broadband radiometric measurements of LEDs with uniform and low-uncertainty results are not available. Currently, either complicated and expensive spectral radiometric measurements or broadband photometric LED measurements are used. The broadband photometric measurements are based on the CIE standardized V(λ) function, which cannot be used in the UV range and leads to large errors when blue or red LEDs are measured in its wings, where the realization is always poor. Reference irradiance meters with spectrally constant response and high-intensity LED irradiance sources were developed here to implement the previously suggested broadband radiometric LED measurement procedure [1, 2]. Using a detector with spectrally constant response, the broadband radiometric quantities of any LEDs or LED groups can be simply measured with low uncertainty without using any source standard. The spectral flatness of filtered-Si detectors and low-noise pyroelectric radiometers are compared. Examples are given for integrated irradiance measurement of UV and blue LED sources using the here introduced reference (standard) pyroelectric irradiance meters. For validation, the broadband measured integrated irradiance of several LED-365 sources were compared with the spectrally determined integrated irradiance derived from an FEL spectral irradiance lamp-standard. Integrated responsivity transfer from the reference irradiance meter to transfer standard and field UV irradiance meters is discussed.

  12. MODOS GUIADOS EM SLABS METAMATERIAIS GUIDED MODES IN METAMATERIAL SLABS

    Directory of Open Access Journals (Sweden)

    Leonardo André Ambrosio

    2006-12-01

    Full Text Available Este trabalho apresenta um estudo de revisão de modos propagantes em um guia-de-onda slab constituído de materiais com índices de refração negativo, os chamados metamateriais, Mostra-se que os modos guiados em um slab metamaterial possuem algumas propriedades particulares, tais como a propagação de ondas lentas simétricas ou anti-simétricas, a ausência de modos fundamentais para ondas rápidas e a possibilidade de propagação de ondas guiadas em um meio menos denso. A análise é baseada em expansões de campo no guia e nos espaços superior e inferior ao mesmo.This paper presents a review of the propagation modes in a slab waveguide consisting of negative refraction index materials, known as metamaterials. Some particular properties of guided modes in a metamaterial slab, such as slow symmetric or antisymmetric slow wave propagation, the absence of fundamental modes for fast waves and the possibility of guided waves in a less dense medium. The analysis is based on field expansions in the guide and the upper and lower spaces of it.

  13. A Broadband Ultrathin Nonlinear Switching Metamaterial

    Directory of Open Access Journals (Sweden)

    E. Zarnousheh Farahani

    2017-05-01

    Full Text Available In this paper, an ultrathin planar nonlinear metamaterial slab is designed and simulated. Nonlinearity is provided through placing diodes in each metamaterial unit cell. The diodes are auto-biased and activated by an incident wave. The proposed structure represents a broadband switching property between two transmission and reflection states depending on the intensity of the incident wave. High permittivity values are presented creating a near zero effective impedance at low power states, around the second resonant mode of the structure unit cell; as the result, the incident wave is reflected. Increasing the incident power to the level which can activate the loaded diodes in the structure results in elimination of the resonance and consequently a drop in the permittivity values near the permeability one as well as a switch to the transmission state. A full wave as well as a nonlinear simulations are performed. An optimization method based on weed colonization is applied to the unit cell of the metamaterial slab to achieve the maximum switching bandwidth. The structure represents a 24% switching bandwidth of a 10 dB reduction in the reflection coefficient.

  14. Fracture Mechanisms and Strengthening of Slab Lasers

    Science.gov (United States)

    Marion, John E.

    1987-04-01

    The fracture mechanisms of slab lasers are examined and the critical defects, induced during optical fabrication, are identified. A rationale for determining an appropriate operating stress for the slab laser is outlined, based on Weibull statistics, and this method is experimentally assessed in full-sized slab fracture tests. Techniques for achieving strong slabs are then examined. We determine that strengthening by subsurface damage minimization has the highest potential for strengthening, but that slab durability must also be enhanced in order for the slab to remain strong in practice. Good chemical durability is achieved by the use of water-proof overcoats. Good mechanical durability is achieved by the use of compressive surface layers. The compressive surface layers prevent the deterioration in slab strength from physical damage to the slab surface.

  15. Long-life slab replacement concrete : [summary].

    Science.gov (United States)

    2015-04-01

    Concrete slab replacement projects in Florida have demonstrated a high incidence of : replacement slab cracking. Causes of cracking have not been reliably determined. University of South Florida researchers : sought to identify the factors or : param...

  16. ARC Code TI: SLAB Spatial Audio Renderer

    Data.gov (United States)

    National Aeronautics and Space Administration — SLAB is a software-based, real-time virtual acoustic environment rendering system being developed as a tool for the study of spatial hearing. SLAB is designed to...

  17. Transient slab flattening beneath Colombia

    Science.gov (United States)

    Wagner, L. S.; Jaramillo, J. S.; Ramírez-Hoyos, L. F.; Monsalve, G.; Cardona, A.; Becker, T. W.

    2017-07-01

    Subduction of the Nazca and Caribbean Plates beneath northwestern Colombia is seen in two distinct Wadati Benioff Zones, one associated with a flat slab to the north and one associated with normal subduction south of 5.5°N. The normal subduction region is characterized by an active arc, whereas the flat slab region has no known Holocene volcanism. We analyze volcanic patterns over the past 14 Ma to show that in the mid-Miocene a continuous arc extended up to 7°N, indicating normal subduction of the Nazca Plate all along Colombia's Pacific margin. However, by 6 Ma, we find a complete cessation of this arc north of 3°N, indicating the presence of a far more laterally extensive flat slab than at present. Volcanism did not resume between 3°N and 6°N until after 4 Ma, consistent with lateral tearing and resteepening of the southern portion of the Colombian flat slab at that time.

  18. Spread prestressed concrete slab beam bridges.

    Science.gov (United States)

    2015-04-01

    TxDOT uses prestressed slab beam bridges for short-span bridges ranging from approximately 3050 ft in : length. These bridges have precast, pretensioned slab beams placed immediately adjacent to one another : with a cast-in-place slab made composi...

  19. Processing and properties of large-sized ceramic slabs

    International Nuclear Information System (INIS)

    Raimondo, M.; Dondi, M.; Zanelli, C.; Guarini, G.; Gozzi, A.; Marani, F.; Fossa, L.

    2010-01-01

    Large-sized ceramic slabs with dimensions up to 360x120 cm 2 and thickness down to 2 mm are manufactured through an innovative ceramic process, starting from porcelain stoneware formulations and involving wet ball milling, spray drying, die-less slow-rate pressing, a single stage of fast drying-firing, and finishing (trimming, assembling of ceramic-fiberglass composites). Fired and unfired industrial slabs were selected and characterized from the technological, compositional (XRF, XRD) and microstructural (SEM) viewpoints. Semi-finished products exhibit a remarkable microstructural uniformity and stability in a rather wide window of firing schedules. The phase composition and compact microstructure of fired slabs are very similar to those of porcelain stoneware tiles. The values of water absorption, bulk density, closed porosity, functional performances as well as mechanical and tribological properties conform to the top quality range of porcelain stoneware tiles. However, the large size coupled with low thickness bestow on the slab a certain degree of flexibility, which is emphasized in ceramic-fiberglass composites. These outstanding performances make the large-sized slabs suitable to be used in novel applications: building and construction (new floorings without dismantling the previous paving, ventilated facades, tunnel coverings, insulating panelling), indoor furnitures (table tops, doors), support for photovoltaic ceramic panels. (Author) 24 refs.

  20. Hybrid Broadcast Broadband TV

    OpenAIRE

    Vaala, Jere

    2014-01-01

    Tämän insinöörityön tarkoituksena oli tutustua Hybrid Broadcast Broadband TV:een sekä TV:n nykytilaan ja tulevaisuuteen. Työ on tehty Metropolia Ammattikorkeakoululle. Media-alalla on menossa murros, joka pakottaa printtimedian ja TV-yhtiöt jatkuviin uudistuksiin. Mainosrahoitteinen TV on myös ongelmissa. Digitalisoituminen on tuonut laajakaistan perinteisten jakelutapojen rinnalle, mikä syö mainostuloja. Käyttöön tulossa oleva Hybrid Broadcast Broadband TV perustuu jo olemassa olevii...

  1. MO-FG-CAMPUS-JeP2-01: 4D-MRI with 3D Radial Sampling and Self-Gating-Based K-Space Sorting: Image Quality Improvement by Slab-Selective Excitation

    International Nuclear Information System (INIS)

    Deng, Z; Pang, J; Tuli, R; Fraass, B; Fan, Z; Yang, W; Bi, X; Hakimian, B; Li, D

    2016-01-01

    Purpose: A recent 4D MRI technique based on 3D radial sampling and self-gating-based K-space sorting has shown promising results in characterizing respiratory motion. However due to continuous acquisition and potentially drastic k-space undersampling resultant images could suffer from low blood-to-tissue contrast and streaking artifacts. In this study 3D radial sampling with slab-selective excitation (SS) was proposed in attempt to enhance blood-to-tissue contrast by exploiting the in-flow effect and to suppress the excess signal from the peripheral structures particularly in the superior-inferior direction. The feasibility of improving image quality by using this approach was investigated through a comparison with the previously developed non-selective excitation (NS) approach. Methods: Two excitation approaches SS and NS were compared in 5 cancer patients (1 lung 1 liver 2 pancreas and 1 esophagus) at 3Tesla. Image artifact was assessed in all patients on a 4-point scale (0: poor; 3: excellent). Signal-tonoise ratio (SNR) of the blood vessel (aorta) at the center of field-of-view and its nearby tissue were measured in 3 of the 5 patients (1 liver 2 pancreas) and blood-to-tissue contrast-to-noise ratio (CNR) were then determined. Results: Compared with NS the image quality of SS was visually improved with overall higher signal in all patients (2.6±0.55 vs. 3.4±0.55). SS showed an approximately 2-fold increase of SNR in the blood (aorta: 16.39±1.95 vs. 32.19±7.93) and slight increase in the surrounding tissue (liver/pancreas: 16.91±1.82 vs. 22.31±3.03). As a result the blood-totissue CNR was dramatically higher in the SS method (1.20±1.20 vs. 9.87±6.67). Conclusion: The proposed 3D radial sampling with slabselective excitation allows for reduced image artifact and improved blood SNR and blood-to-tissue CNR. The success of this technique could potentially benefit patients with cancerous tumors that have invaded the surrounding blood vessels where radiation

  2. Broadband Internet and Income Inequality

    OpenAIRE

    HOUNGBONON , Georges Vivien; Liang , Julienne

    2017-01-01

    Policy makers are aiming for a large coverage of high-speed broadband Internet. However , there is still a lack of evidence about its effects on income distribution. In this paper, we investigate the effects of fixed broadband Internet on mean income and income inequality using a unique town-level data on broadband adoption and quality in France. We find that broadband adoption and quality raise mean income and lower income inequality. These results are robust to initial conditions, and yield...

  3. STRUCTURE FORMATION IN FOUNDATION SLAB CONCRETE

    Directory of Open Access Journals (Sweden)

    V. V. Kovalenko

    2016-04-01

    Full Text Available Purpose. The work involves identifying the dependence of structural and mechanical properties of the concrete on the composition of used modifier additives, the nature of changes of structural and mechanical properties depending on the period of concrete hardening of test and modified samples. Methodology. The applied microstructural, fractographic, microprobe analyses and physico-mechanical tests revealed the required dependencies. Findings. The microstructure of the cement stone under equal conditions of concrete mix selection depends on the composition of used raw materials and production technology. This paper investigates the structural changes in the setting time of hard mixture concrete and effect of component parts of the complex modifier additive PLKP (produced by «Logia», Dnepropetrovsk on morphology, dispersion and chemical composition of the cement stone, as well as the mechanical characteristics of concrete for the foundation slab. The study of the structural and physical-mechanical characteristics of the test samples and modified concrete at various hardening stages showed that the use Ukrainian hyper-plasticizer PLKP contributes to the formation of nano-structured concrete. The addition of hardening accelerators to the super-plasticizer additive reduces the diameter of crystal whiskers, increases the structural homogeneity and stability and improves the complex of the concrete mechanical characteristics. Application of new PLKP polycarboxylate additives in the production of concrete mixtures for the foundation slab allows eliminating the steaming from the foundation slab production technology. The absence of salt component in the additive improves the concrete durability. Originality. The paper showed that modification of the concrete with complex additive PLKP facilitates the formation of the most homogeneous structure of cement stone, which consists of compact crystals surrounded by fibrous crystals that are tightly

  4. Method for Bubbledeck Concrete Slab with Gaps

    Directory of Open Access Journals (Sweden)

    Sergiu Călin

    2009-01-01

    Full Text Available The composite slabs are made of BubbleDeck type slab elements with spherical gaps, poured in place on transversal and longitudinal directions. By introducing the gaps leads to a 30...50\\% lighter slab which reduces the loads on the columns, walls and foundations, and of course of the entire building. BubbleDeck slab elements are plates with ribs on two directions made of reinforced concrete or precast concrete with spherical shaped bubbles. These slab elements have a bottom and an upper concrete part connected with vertical ribs that go around the gaps.

  5. Broadband and the Internet.

    Science.gov (United States)

    Gutierrez, Vicente

    2002-01-01

    The Internet is a tool one can use every day to get information. In every location, the way you can access the Internet is different. The purpose of this article is to review the different types of Internet access available with emphasis on broadband. The advantages and disadvantages of every type of access are discussed.

  6. Czech way to broadband

    Czech Academy of Sciences Publication Activity Database

    Kuchar, Anton; Peterka, J.; Hrstka, J.; Hankiewiczová, H.

    -, August (2006), s. 274-278 ISSN 1106-2975. [FITCE Congress /45./. Athens, 30.08.2006-02.09.2006] Grant - others:BReATH Consortium EU(XE) EC FP6 1ST Programme Institutional research plan: CEZ:AV0Z20670512 Keywords : telecommunication networks * Internet * broadband networks Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering

  7. Multicarrier Block-Spread CDMA for Broadband Cellular Downlink

    NARCIS (Netherlands)

    Petré, F.; Leus, G.; Moonen, M.; De Man, H.

    2004-01-01

    Effective suppression of multiuser interference (MUI) and mitigation of frequency-selective fading effects within the complexity constraints of the mobile constitute major challenges for broadband cellular downlink transceiver design. Existing wideband direct-sequence (DS) code division multiple

  8. Broadband Liner Optimization for the Source Diagnostic Test Fan

    Science.gov (United States)

    Nark, Douglas M.; Jones, Michael G.

    2012-01-01

    The broadband component of fan noise has grown in relevance with the utilization of increased bypass ratio and advanced fan designs. Thus, while the attenuation of fan tones remains paramount, the ability to simultaneously reduce broadband fan noise levels has become more appealing. This paper describes a broadband acoustic liner optimization study for the scale model Source Diagnostic Test fan. Specifically, in-duct attenuation predictions with a statistical fan source model are used to obtain optimum impedance spectra over a number of flow conditions for three liner locations in the bypass duct. The predicted optimum impedance information is then used with acoustic liner modeling tools to design liners aimed at producing impedance spectra that most closely match the predicted optimum values. Design selection is based on an acceptance criterion that provides the ability to apply increased weighting to specific frequencies and/or operating conditions. Typical tonal liner designs targeting single frequencies at one operating condition are first produced to provide baseline performance information. These are followed by multiple broadband design approaches culminating in a broadband liner targeting the full range of frequencies and operating conditions. The broadband liner is found to satisfy the optimum impedance objectives much better than the tonal liner designs. In addition, the broadband liner is found to provide better attenuation than the tonal designs over the full range of frequencies and operating conditions considered. Thus, the current study successfully establishes a process for the initial design and evaluation of novel broadband liner concepts for complex engine configurations.

  9. Enhanced Accelerated Drying of Concrete Floor Slabs

    OpenAIRE

    Holmes, Niall; West, Roger P.

    2013-01-01

    Concrete floor slabs dry out through a process of evaporation and diffusion provided the ambient environment promotes such drying. Impermeable floor coverings laid on concrete slabs can be subject to damage caused by high levels of residual moisture trapped by premature sealing of the surface. This damage can include timber floor boards buckling, vinyls blistering or tiles lifting. Whether or not it is safe to apply such a covering depends on whether the slab is sufficiently dry. Furthermore,...

  10. Generating Atomistic Slab Surfaces with Adsorbates

    Science.gov (United States)

    2017-12-01

    of spatial orientation on the possible adsorption sites. This framework was developed to coordinate the passing of structure information throughout...when making slabs. The list should be composed of strings that represent the name of the compound to skip. If no list is given for settings, then...8217_’+str(min_vac)) # Makes a slab directory except: pass iface_slab = Interface(structure, hkl

  11. Distribution of slab-derived fluids around the edge of the Philippine Sea Plate from Central to Northeast Japan

    Science.gov (United States)

    Nakamura, Hitomi; Iwamori, Hikaru; Ishizuka, Osamu; Nishizawa, Tatsuji

    2018-01-01

    Marginal parts of a plate and subducting slab can play important roles in geodynamics. This is because in areas where a plate interacts with other plates or with the mantle thermal, geochemical, and mechanical interactions are expected. The Philippine Sea (PHS) slab that subducts beneath the Japan arcs has such an edge. To examine the relationship between arc magmatism and the slab edge in the transition zone from Northeast Japan to Central Japan, we investigated isotopic systematics of the regional volcanic rocks, incorporating data from literature and new data for five isotopic ratios of Sr, Nd, and Pb. The new data included major element compositions of 22 samples from the back-arc area, and 5 isotopic ratios for 6 samples selected from Pleistocene to early Quaternary epochs. Consequently, several findings were determined based on the spatial variation of the isotopic ratios and the estimated amount of slab-derived fluid: (1) the amount of fluid derived from the two subducting slabs (i.e., the Pacific slab and the PHS slab) decreases northward from a significantly high value ( 5 wt% fluid added to the source mantle), away from the seismically determined edge of the PHS slab; (2) the proportion of the PHS component in the total slab-derived fluid also decays northward; and (3) the PHS component spreads to the north beyond the seismically determined edge of the PHS slab. These observations strongly suggest that the existence of an aseismic PHS slab beneath southernmost parts of Northeast Japan delivers the PHS component to the arc magmatism. As was indicated by previous geodynamical studies, subduction of the PHS and PAC slabs may generate suction force towards the corner of mantle wedge, which might account for the large amount of fluid near the seismically determined slab edge as described in (1) above.

  12. Broadband Radio Service (BRS) and Educational Broadband Service (EBS) Transmitters

    Data.gov (United States)

    Department of Homeland Security — The Broadband Radio Service (BRS), formerly known as the Multipoint Distribution Service (MDS)/Multichannel Multipoint Distribution Service (MMDS), is a commercial...

  13. Analysis and design of reinforced concrete slab

    OpenAIRE

    Kališnik, Žiga

    2014-01-01

    The graduation thesis examines the analysis and design of a reinforced concrete slab. Slab loads are based on guidelines from standards SIST EN 1990 and SIST EN 1991-1-1, and the design is made according to standard SIST EN 1992-1-1, which covers concrete structures' design. The slab is analysed with finite element method using Safe computer code. The process of modeling slab structure in Safe computer code is described. Based on loads from ultimate limit state reinforcement is calculated and...

  14. Numerical Modelling of Reinforced Concrete Slabs under Blast Loads of Close-in Detonations Using the Lagrangian Approach

    Science.gov (United States)

    Shuaib, M.; Daoud, O.

    2015-07-01

    This paper includes an investigation for the deformations, including deflections and damage modes, which occur in reinforced concrete (RC) slabs when subjected to blast loads of explosions. The slab considered for the investigation is a one-way square RC slab with the dimensions of 1000 x 1000 x 40 mm, fixed supported at two opposite sides. It was subjected to close-in detonations of three different charge weights for a constant standoff distance. For the study, the slab was analysed using the numerical method by means of nonlinear finite element analysis. The slab was modelled as 3-D structural continuum using LS-DYNA software. For concrete modelling, two constitutive models were selected, namely the KCC and Winfrith concrete models. Blast loads were applied to the slab through the Lagrangian approach, and the blast command available in the software, namely LOAD_BLAST_ENHANCED, was selected for the application. The deflections and damage modes results obtained were compared to those from a previously published experiment. From the study, both the KCC and Winfrith concrete models effectively and satisfactorily estimated the actual slab maximum deflection. For damage modes, the KCC model appeared to be capable to capture satisfactorily the general damage mode including flexural cracks. However, the model could not capture the local shear mode at the middle of slab (spallation) because the Lagrangian approach does not simulate the interaction between the ambient air and the solid slab.

  15. Bridge approach slabs for Missouri DOT field evaluation of alternative and cost efficient bridge approach slabs.

    Science.gov (United States)

    2013-05-01

    Based on a recent study on cost efficient alternative bridge approach slab (BAS) designs (Thiagarajan et : al. 2010) has recommended three new BAS designs for possible implementation by MoDOT namely a) 20 feet cast-inplace : slab with sleeper slab (C...

  16. Global Adjoint Tomography - Hotspots and Slabs

    Science.gov (United States)

    Ruan, Y.; Lei, W.; Lefebvre, M. P.; Modrak, R. T.; Smith, J. A.; Orsvuran, R.; Bozdag, E.; Tromp, J.

    2017-12-01

    Plumes rise from the deep mantle due to thermal or/and chemical buoyancy, forming hotspots at the surface, and oceanic plates subduct underneath continents, piling up at discontinuities or sinking down to the core-mantle boundary. Despite these basic convection mechanisms, many questions remain about the origin of mantle plumes, slab subduction, their interaction with mantle convection, and their relationship with the large low shear velocity provinces (LLSVPs) at the base of the mantle. Plume and slab morphology at depth provide further insight into these questions but imaging them in the mid and lower mantle is known to be very challenging due to a lack of data coverage and resolvability limits of conventional body-wave traveltime tomography. The deployment of regional dense arrays (e.g., USArray) and development of full waveform inversion techniques provide opportunities to resolve finer 3D details of mantle plumes and slabs. Harnessing the power of supercomputer ''Titan'' at Oak Ridge National Laboratory, we employed a spectral-element method to accurately simulate seismograms in complex 3D Earth models and an adjoint method to obtain model updates. Bozdag et al. (2016) iteratively determined a transversely isotropic earth model (GLAD_M15) using 253 events. To achieve higher resolution and better coverage in the deep mantle, we expanded our database to 1,040 events; a 1/3 of them are deep earthquakes (>500 km). We reinverted source parameters using model GLAD_M15, recalculated synthetic seismograms, selected time windows that show good agreement between data and the synthetics, and made measurements within these windows. From the measurements, we further assess the overall quality of each event and station and exclude bad measurements using very conservative criteria. Thus far, we assimilated more than 10 million windows in three period bands from 17-250 s. As the model improves, we correct the centroid time and scalar moment of each event using its mean

  17. Broadband terahertz fiber directional coupler

    DEFF Research Database (Denmark)

    Nielsen, Kristian; Rasmussen, Henrik K.; Jepsen, Peter Uhd

    2010-01-01

    We present the design of a short broadband fiber directional coupler for terahertz (THz) radiation and demonstrate a 3 dB coupler with a bandwidth of 0:6 THz centered at 1:4 THz. The broadband coupling is achieved by mechanically downdoping the cores of a dual-core photonic crystal fiber by micro......We present the design of a short broadband fiber directional coupler for terahertz (THz) radiation and demonstrate a 3 dB coupler with a bandwidth of 0:6 THz centered at 1:4 THz. The broadband coupling is achieved by mechanically downdoping the cores of a dual-core photonic crystal fiber...

  18. A slab expression in the Gibraltar arc?

    Science.gov (United States)

    Nijholt, Nicolai; Govers, Rob; Wortel, Rinus

    2017-04-01

    The present-day geodynamic setting of the Gibraltar arc region results from several Myrs of subduction rollback in the overall (oblique) convergence of Africa and Iberia. As for most rollback settings in a convergence zone, the interaction of these two components is complex and distinctly non-stationary. Gibraltar slab rollback is considered to have stalled, or at least diminished largely in magnitude, since the late Miocene/early Pliocene, suggesting that the effect of the slab on present-day surface motions is negligible. However, GPS measurements indicate that the Gibraltar arc region has an anomalous motion with respect to both Iberia and Africa, i.e., the Gibraltar arc region does not move as part of the rigid Iberian, or the rigid African plate. A key question is whether this surface motion is an expression of the Gibraltar slab. Seismic activity in the Gibraltar region is diffuse and considerable in magnitude, making it a region of high seismic risk. Unlike the North African margin to the east, where thrust earthquakes dominate the focal mechanism tables, a complex pattern is observed with thrust, normal and strike-slip earthquakes in a region stretching between the northern Moroccan Atlas across the Gibraltar arc and Alboran Sea (with the Trans-Alboran Shear Zone) to the Betics of southern Spain. Even though no large mega-thrust earthquakes have been observed in recent history, slab rollback may not have completely ceased. However, since no activity has been observed in the accretionary wedge, probably since the Pliocene, it is likely that the subduction interface is locked. In this study, we perform a series of numerical models in which we combine the relative plate convergence, variable magnitude of friction on fault segments, regional variations in gravitational potential energy and slab pull of the Gibraltar slab. We seek to reproduce the GPS velocities and slip sense on regional faults and thereby determine whether the Gibraltar slab has an effect on

  19. Constraining subducted slab properties with deep earthquakes

    Science.gov (United States)

    Zhan, Z.; Yang, T.; Gurnis, M.; Shen, Z.; Wu, F.

    2017-12-01

    The discovery of deep earthquakes and Wadati-Benioff zone was a critical piece in the early history of plate tectonics. Today, deep earthquakes continue to serve as important markers/probes of subducted slab geometry, structure, and stress state. Here we discuss three examples in which we have recently used deep earthquakes to provide new insights to subducted slab properties. In the first application, we investigate the slab morphology and stress regimes under different trench motion histories with geodynamic models. We find that the isolation of the 2015 Mw 7.9 Bonin Islands deep earthquake from the background Wadati-Benioff zone may be explained as a result of Pacific slab buckling in response to the slow trench retreat. Additionally, subducted slab is inherently heterogeneous due to non-linear viscosity, contributing to the occurrences of isolated deep earthquakes. In the second application, we quantify the coda waveform differences from nearby deep earthquakes to image fine-scale slab structures. We find that large metastable olivine wedge suggested by several previous studies can not fit our observations. Therefore, the effects of metastable olivine on slab dynamics should be re-assessed. In the third application, we take advantage of P and S differential travel times from deep earthquake clusters to isolate signatures of Vp/Vs ratios within slabs from ambient mantle. We observe substantial deviations of slab Vp/Vs from that in 1D reference Earth models, and even possible lateral variations. This sheds light on potential difference in slab temperature or water content. All three applications underscore that deep earthquakes are still incredibly useful in informing us more about subducted slabs.

  20. LASERS: A cryogenic slab CO laser

    Science.gov (United States)

    Ionin, Andrei A.; Kozlov, A. Yu; Seleznev, L. V.; Sinitsyn, D. V.

    2009-03-01

    A compact capacitive transverse RF-discharge-pumped slab CO laser with cryogenically cooled electrodes, which operates both in the cw and repetitively pulsed regimes, is fabricated. The laser operation is studied in the free running multifrequency regime at the vibrational - rotational transitions of the fundamental (V + 1 → V) vibrational bands of the CO molecule in the spectral region from 5.1 to 5.4 μm. Optimal operation conditions (gas mixture composition and pressure, RF pump parameters) are determined. It is shown that only gas mixtures with a high content of oxygen (up to 20% with respect to the concentration of CO molecules) can be used as an active medium of this laser. It is demonstrated that repetitively pulsed pumping is more efficient compared to cw pumping. In this case, quasi-cw lasing regime can be obtained. The maximum average output power of ~12 W was obtained for this laser operating on fundamental bands and its efficiency achieved ~14 %. The frequency-selective operation regime of the slab RF-discharge-pumped CO laser was realised at ~ 100 laser lines in the spectral region from 5.0 to 6.5 μm with the average output power of up to several tens of milliwatts in each line. Lasing at the transitions of the first vibrational overtone (V + 2 → V) of the CO molecule is obtained in the spectral region from 2.5 to 3.9 μm. The average output power of the overtone laser achieved 0.3 W. All the results were obtained without the forced gas mixture exchange in the discharge chamber. Under fixed experimental conditions, repetitively pulsed lasing (with fluctuations of the output characteristics no more than ±10 %) was stable for more than an hour.

  1. Evaluating the potential shielding properties of periodic metamaterial slabs

    OpenAIRE

    SEETHARAMDOO, D; BERBINEAU, M; TAROT, A; MAHDJOUBI, K

    2009-01-01

    Metamaterials can prove to be good candidates for shields in EMC applications where weight reduction is a challenge. Indeed metamaterial slabs can provide the same reflective properties as conventional metallic screens but with a lower density and reduced weight. Another advantage is that they can be tailored to exhibit required frequency-selective properties. However, their performance in terms of shielding performance has yet to be evaluated. In this paper, a method to evaluate the shieldin...

  2. 0-6722 : spread prestressed concrete slab beam bridges.

    Science.gov (United States)

    2014-08-01

    The Texas Department of Transportation uses : precast prestressed concrete slab beam bridges for : shorter-span bridges of approximately 3050 ft in : length. Conventional slab beam bridges have slab : beams placed immediately adjacent to one anoth...

  3. Shear assessment of reinforced concrete slab bridges

    NARCIS (Netherlands)

    Lantsoght, E.O.L.; Van der Veen, C.; Walraven, J.C.; De Boer, A.

    2013-01-01

    The capacity of reinforced concrete solid slab bridges in shear is assessed by comparing the design beam shear resistance to the design value of the applied shear force due to the permanent actions and live loads. Results from experiments on half-scale continuous slab bridges are used to develop a

  4. Thin-slab casting–New possibilities

    Indian Academy of Sciences (India)

    Additionally, what started as a step for reducing investment in hot rolling has, in fact, given new opportunity for direct hot rolling of thickness that were, for long, ... A techno-economic analysis of thin-slab casting has been presented along with the benefits that arise when a thin-slab caster is linked to the blast furnace and ...

  5. Photon transport in thin disordered slabs

    Indian Academy of Sciences (India)

    This approximation of an incoherent energy transport is valid in the weak scattering limit ( Р*. ^ 1, where = 2. ). In this paper, we describe the results of our Monte Carlo simulations to study photon transport in thin slabs. We show that in small slabs, photons that traverse large paths are forced by the constrained geometry to ...

  6. The 2017 Mw 8.2 Chiapas, Mexico, Earthquake: Energetic Slab Detachment

    Science.gov (United States)

    Ye, Lingling; Lay, Thorne; Bai, Yefei; Cheung, Kwok Fai; Kanamori, Hiroo

    2017-12-01

    On 8 September 2017, a great (Mw 8.2) normal faulting earthquake ruptured within the subducting Cocos Plate 70 km landward from the Middle American Trench beneath the Tehuantepec gap. Iterative inversion and modeling of teleseismic and tsunami data and prediction of GPS displacements indicate that the steeply dipping rupture extended 180 km to the northwest along strike toward the Oaxaca coast and from 30 to 70 km in depth, with peak slip of 13 m. The rupture likely broke through the entire lithosphere of the young subducted slab in response to downdip slab pull. The plate boundary region between the trench and the fault intersection with the megathrust appears to be frictionally coupled, influencing location of the detachment. Comparisons of the broadband body wave magnitude (mB) and moment-scaled radiated energy (ER/M0) establish that intraslab earthquakes tend to be more energetic than interplate events, accounting for strong ground shaking observed for the 2017 event.

  7. Diode-side-pumped Alexandrite slab lasers.

    Science.gov (United States)

    Damzen, M J; Thomas, G M; Minassian, A

    2017-05-15

    We present the investigation of diode-side-pumping of Alexandrite slab lasers in a range of designs using linear cavity and grazing-incidence bounce cavity configurations. An Alexandrite slab laser cavity with double-pass side pumping produces 23.4 mJ free-running energy at 100 Hz rate with slope efficiency ~40% with respect to absorbed pump energy. In a slab laser with single-bounce geometry output power of 12.2 W is produced, and in a double-bounce configuration 6.5 W multimode and 4.5 W output in TEM 00 mode is produced. These first results of slab laser and amplifier designs in this paper highlight some of the potential strategies for power and energy scaling of Alexandrite using diode-side-pumped Alexandrite slab architectures with future availability of higher power red diode pumping.

  8. Broadband pendulum energy harvester

    Science.gov (United States)

    Liang, Changwei; Wu, You; Zuo, Lei

    2016-09-01

    A novel electromagnetic pendulum energy harvester with mechanical motion rectifier (MMR) is proposed and investigated in this paper. MMR is a mechanism which rectifies the bidirectional swing motion of the pendulum into unidirectional rotation of the generator by using two one-way clutches in the gear system. In this paper, two prototypes of pendulum energy harvester with MMR and without MMR are designed and fabricated. The dynamic model of the proposed MMR pendulum energy harvester is established by considering the engagement and disengagement of the one way clutches. The simulation results show that the proposed MMR pendulum energy harvester has a larger output power at high frequencies comparing with non-MMR pendulum energy harvester which benefits from the disengagement of one-way clutch during pendulum vibration. Moreover, the proposed MMR pendulum energy harvester is broadband compare with non-MMR pendulum energy harvester, especially when the equivalent inertia is large. An experiment is also conducted to compare the energy harvesting performance of these two prototypes. A flywheel is attached at the end of the generator to make the disengagement more significant. The experiment results also verify that MMR pendulum energy harvester is broadband and has a larger output power at high frequency over the non-MMR pendulum energy harvester.

  9. An Assessment of Emerging Wireless Broadband Technologies

    National Research Council Canada - National Science Library

    Fountanas, Leonidas

    2001-01-01

    ... technologies in providing broadband services today, emerging wireless broadband technologies are expected to significantly increase their market share over the next years, Deploying a wireless network...

  10. A broadband low-reflection bending waveguide for airborne sound

    Science.gov (United States)

    Kan, Weiwei; Liang, Bin; Tian, Cong; Shen, Zhonghua; Cheng, Jianchun

    2017-06-01

    We design a bending waveguide capable to transmit broadband airborne sound with high efficiency while maintaining the wavefront undisturbed. Based on coordinate transformation, analytical formulae are derived to predict the parameter distribution of the required constituent materials composing the waveguide. A practical implementation is presented by employing acoustic metafluids that are formed with periodically arranged slabs of subwavelength dimensions in air-filled acoustic chambers. By studying the acoustic properties of the unit structures in the quasi-static limit, it is demonstrated that the effective mass density and bulk modulus of the proposed metamaterial can be modulated independently by tuning the geometry parameters and the temperature in the chamber. By virtue of the free-modulated features, the range of realizable effective parameters with metafluid are substantially broadened, and the corresponding acoustic impedance can be perfectly matched to the background medium. The performance of the bending waveguide is verified by demonstrating the low-reflection transmission of broadband sound and the ability of keeping the wavefront undisturbed. According to the effective medium theory, our scheme offers the flexibility to further raise the upper limit of the operating frequency with smaller size individual elements. The proposed design with the advantage of feasibility and effectiveness in broadband shows potential for a wide range of wave-steering applications.

  11. Cretaceous Arctic magmatism: Slab vs. plume? Or slab and plume?

    Science.gov (United States)

    Gottlieb, E. S.; Miller, E. L.; Andronikov, A. V.; Brumley, K.; Mayer, L. A.; Mukasa, S. B.

    2010-12-01

    Tectonic models for the Cretaceous paleogeographic evolution of the Arctic Ocean and its adjacent landmasses propose that rifting in the Amerasia Basin (AB) began in Jura-Cretaceous time, accompanied by the development of the High Arctic Large Igneous Province (HALIP). During the same timespan, deformation and slab-related magmatism, followed by intra-arc rifting, took place along the Pacific side of what was to become the Arctic Ocean. A compilation and comparison of the ages, characteristics and space-time variation of circum-Arctic magmatism allows for a better understanding of the role of Pacific margin versus Arctic-Atlantic plate tectonics and the role of plume-related magmatism in the origin of the Arctic Ocean. In Jura-Cretaceous time, an arc built upon older terranes overthrust the Arctic continental margins of North America and Eurasia, shedding debris into foreland basins in the Brooks Range, Alaska, across Chukotka, Russia, to the Lena Delta and New Siberian Islands region of the Russian Arctic. These syn-tectonic sediments have some common sources (e.g., ~250-300 Ma magmatic rocks) as determined by U-Pb detrital zircon geochronology. They are as young as Valanginian-Berriasian (~136 Ma, Gradstein et al., 2004) and place a lower limit on the age of formation of the AB. Subsequent intrusions of granitoid plutons, inferred to be ultimately slab-retreat related, form a belt along the far eastern Russian Arctic continental margin onto Seward Peninsula and have yielded a continuous succession of zircon U-Pb ages from ~137-95 Ma (n=28) and a younger suite ~91-82 Ma (n=16). All plutons dated were intruded in an extensional tectonic setting based on their relations to wall-rock deformation. Regional distribution of ages shows a southward migration of the locus of magmatism during Cretaceous time. Basaltic lavas as old as 130 Ma and as young as 80 Ma (40Ar/39Ar)) erupted across the Canadian Arctic Islands, Svalbard and Franz Josef Land and are associated with

  12. Broadband CyberShake Platform: Seismogram Synthesis for Broadband Physics-Based Probabilistic Seismic Hazard Analysis

    Science.gov (United States)

    Callaghan, S.; Maechling, P. J.; Small, P.; Milner, K.; Graves, R. W.; Jordan, T. H.; CyberShake Collaboration

    2011-12-01

    Researchers at the Southern California Earthquake Center (SCEC) have developed the CyberShake computational platform to perform probabilistic seismic hazard analysis (PSHA) in the Los Angeles region (Graves et al., 2010) using deterministic wave propagation simulations at frequencies up to 0.5 Hz. CyberShake uses seismic reciprocity to calculate synthetic seismograms for a suite of more than 600,000 rupture realizations. From this set of seismograms we compute intensity measures, which are then combined into a PSHA hazard curve for the site of interest. SCEC has also developed the SCEC Broadband Ground Motion Simulation Platform, a software system that can calculate broadband seismograms at frequencies up to 10 Hz for historical and scenario earthquakes using multiple earthquake rupture generators, multiple low- and high-frequency wave propagation simulation codes, and multiple site effects modules. Here we report how we have integrated the high-frequency computational capabilities of the SCEC Broadband Platform into CyberShake, producing the Broadband CyberShake Platform. The Broadband CyberShake Platform extends the frequency range up to 10 Hz by combining low frequency deterministic synthetic seismograms with higher frequency stochastic seismograms. We can now calculate physics-based seismograms and PSHA hazard curves for intensity measures such as PGA that are strongly dependent on higher frequency ground motions. A potential benefit of this approach, particularly at higher frequencies, is that given adequate sampling of the parameter space, the physics-based model naturally limits the upper bound of the estimated ground motion response. This often leads to a reduction in hazard at longer return periods. We are applying the computational capabilities of the SCEC Broadband CyberShake Platform at southern California sites selected to support validation of this newly developed PSHA computational technique. This includes calculation of Broadband Cyber

  13. Broadband unidirectional ultrasound propagation

    Science.gov (United States)

    Sinha, Dipen N.; Pantea, Cristian

    2017-12-12

    A passive, linear arrangement of a sonic crystal-based apparatus and method including a 1D sonic crystal, a nonlinear medium, and an acoustic low-pass filter, for permitting unidirectional broadband ultrasound propagation as a collimated beam for underwater, air or other fluid communication, are described. The signal to be transmitted is first used to modulate a high-frequency ultrasonic carrier wave which is directed into the sonic crystal side of the apparatus. The apparatus processes the modulated signal, whereby the original low-frequency signal exits the apparatus as a collimated beam on the side of the apparatus opposite the sonic crystal. The sonic crystal provides a bandpass acoustic filter through which the modulated high-frequency ultrasonic signal passes, and the nonlinear medium demodulates the modulated signal and recovers the low-frequency sound beam. The low-pass filter removes remaining high-frequency components, and contributes to the unidirectional property of the apparatus.

  14. Estimation of the Reliability of Plastic Slabs

    DEFF Research Database (Denmark)

    Pirzada, G. B. : Ph.D.

    In this thesis, work related to fundamental conditions has been extended to non-fundamental or the general case of probabilistic analysis. Finally, using the ss-unzipping technique a door has been opened to system reliability analysis of plastic slabs. An attempt has been made in this thesis...... to give a probabilistic treatment of plastic slabs which is parallel to the deterministic and systematic treatment of plastic slabs by Nielsen (3). The fundamental reason is that in Nielsen (3) the treatment is based on a deterministic modelling of the basic material properties for the reinforced...

  15. Differential uncertainty analysis for evaluating the accuracy of S-parameter retrieval methods for electromagnetic properties of metamaterial slabs.

    Science.gov (United States)

    Hasar, Ugur Cem; Barroso, Joaquim J; Sabah, Cumali; Kaya, Yunus; Ertugrul, Mehmet

    2012-12-17

    We apply a complete uncertainty analysis, not studied in the literature, to investigate the dependences of retrieved electromagnetic properties of two MM slabs (the first one with only split-ring resonators (SRRs) and the second with SRRs and a continuous wire) with single-band and dual-band resonating properties on the measured/simulated scattering parameters, the slab length, and the operating frequency. Such an analysis is necessary for the selection of a suitable retrieval method together with the correct examination of exotic properties of MM slabs especially in their resonance regions. For this analysis, a differential uncertainty model is developed to monitor minute changes in the dependent variables (electromagnetic properties of MM slabs) in functions of independent variables (scattering (S-) parameters, the slab length, and the operating frequency). Two complementary approaches (the analytical approach and the dispersion model approach) each with different strengths are utilized to retrieve the electromagnetic properties of various MM slabs, which are needed for the application of the uncertainty analysis. We note the following important results from our investigation. First, uncertainties in the retrieved electromagnetic properties of the analyzed MM slabs drastically increase when values of electromagnetic properties shrink to zero or near resonance regions where S-parameters exhibit rapid changes. Second, any low-loss or medium-loss inside the MM slabs due to an imperfect dielectric substrate or a finite conductivity of metals can decrease these uncertainties near resonance regions because these losses hinder abrupt changes in S-parameters. Finally, we note that precise information of especially the slab length and the operating frequency is a prerequisite for accurate analysis of exotic electromagnetic properties of MM slabs (especially multiband MM slabs) near resonance regions.

  16. Developing a Broadband Adoption Model in the UK Context

    Science.gov (United States)

    Dwivedi, Yogesh K.; Mustafee, Navonil; Williams, Michael D.; Lal, Banita

    This research examines the factors affecting the consumer adoption of broadband in the United Kingdom. A conceptual model of broadband adoption was developed by selecting and justifying a number of relevant constructs from the technology adoption literature. The model was then empirically tested by employing survey data that was randomly collected from 358 UK broadband consumers. The findings suggest that, with the exception of one construct that was included in the conceptual model (namely, knowledge), all of the con structs significantly influence consumers when adopting broadband in a UK household. The significant constructs include relative advantage, utilitarian outcomes, hedonic outcomes, primary influence, facilitating conditions resources, and self-efficacy. Furthermore, when considering the behavioral intention and facilitating conditions resources constructs together, they significantly explain UK broad band adoption behavior. The theoretical contri bution of this research is that it determines and integrates the appropriate constructs from the technology adoption literature in order to enhance the knowledge of technology adoption from the consumer's perspective. This research has implications for policy makers and broadband providers since the results of this study can be exploited by the aforementioned stakeholders in order to encourage and promote the adoption and usage of broadband among the general population.

  17. Broadband direct RF digitization receivers

    CERN Document Server

    Jamin, Olivier

    2014-01-01

    This book discusses the trade-offs involved in designing direct RF digitization receivers for the radio frequency and digital signal processing domains.  A system-level framework is developed, quantifying the relevant impairments of the signal processing chain, through a comprehensive system-level analysis.  Special focus is given to noise analysis (thermal noise, quantization noise, saturation noise, signal-dependent noise), broadband non-linear distortion analysis, including the impact of the sampling strategy (low-pass, band-pass), analysis of time-interleaved ADC channel mismatches, sampling clock purity and digital channel selection. The system-level framework described is applied to the design of a cable multi-channel RF direct digitization receiver. An optimum RF signal conditioning, and some algorithms (automatic gain control loop, RF front-end amplitude equalization control loop) are used to relax the requirements of a 2.7GHz 11-bit ADC. A two-chip implementation is presented, using BiCMOS and 65nm...

  18. Mantle wedge serpentinization effects on slab dips

    Directory of Open Access Journals (Sweden)

    Eh Tan

    2017-01-01

    Full Text Available The mechanical coupling between a subducting slab and the overlying mantle wedge is an important factor in controlling the subduction dip angle and the flow in mantel wedge. This paper investigates the role of the amount of mantle serpentinization on the subduction zone evolution. With numerical thermos-mechanical models with elasto-visco-plastic rheology, we vary the thickness and depth extent of mantle serpentinization in the mantle wedge to control the degree of coupling between the slab and mantle wedge. A thin serpentinized mantle layer is required for stable subduction. For models with stable subduction, we find that the slab dip is affected by the down-dip extent and the mantle serpentinization thickness. A critical down-dip extent exists in mantle serpentinization, determined by the thickness of the overriding lithosphere. If the down-dip extent does not exceed the critical depth, the slab is partially coupled to the overriding lithosphere and has a constant dip angle regardless of the mantle serpentinization thickness. However, if the down-dip extent exceeds the critical depth, the slab and the base of the overriding lithosphere would be separated and decoupled by a thick layer of serpentinized peridotite. This allows further slab bending and results in steeper slab dip. Increasing mantle serpentinization thickness will also result in larger slab dip. We also find that with weak mantle wedge, there is no material flowing from the asthenosphere into the serpentinized mantle wedge. All of these results indicate that serpentinization is an important ingredient when studying the subduction dynamics in the mantle wedge.

  19. FLEXURAL BEHAVIOUR OF FERROCEMENT COMPOSITE SLAB.

    OpenAIRE

    S.Dharanidharan *

    2016-01-01

    This project deals with an investigational program to understood the flexural behavior of a Ferro cement composite slabs under mid third loading. The concept of composite slabs bring in shut decking or shear connectors are well established. But still, in countries like India, the application of same is limited due to difficulties in manufacture and also due to concerns like fire resistance, durability, aesthetics etc., this study is an attempt to exploit the concept of steel – concrete compos...

  20. Photocatalytic, highly hydrophilic porcelain stoneware slabs

    Science.gov (United States)

    Raimondo, M.; Guarini, G.; Zanelli, C.; Marani, F.; Fossa, L.; Dondi, M.

    2011-10-01

    Photocatalytic, highly hydrophilic industrial porcelain stoneware large slabs were realized by deposition of nanostructured TiO2 coatings. Different surface finishing and experimental conditions were considered in order to assess the industrial feasibility. Photocatalytic and wetting behaviour of functionalized slabs mainly depends on surface phase composition in terms of anatase/rutile ratio, this involving - as a key issue - the deposition of TiO2 on industrially sintered products with an additional annealing step to strengthen coatings' performances and durability.

  1. Slab Waveguide and Optical Fibers for Novel Plasmonic Sensor Configurations.

    Science.gov (United States)

    Cennamo, Nunzio; Mattiello, Francesco; Zeni, Luigi

    2017-06-24

    The use of plasmonic sensor devices often requires replaceable parts and disposable chips for easy, fast and on-site detection analysis. In light of these requests, we propose a novel low-cost surface plasmon resonance sensor platform for possible selective detection of analytes in aqueous solutions. It is based on a Polymethyl methacrylate (PMMA) slab waveguide with a thin gold film on the top surface inserted in a special holder, designed to produce the plasmonic resonance at the gold-dielectric interface. A wide-band light is launched in the PMMA slab waveguide through a trench realized in the holder directly, and illuminated with a PMMA plastic optical fiber (POF) to excite surface Plasmon waves. The output light is then collected by another PMMA POF kept at the end of the slab at an angle of 90° to the trench, and carried to a spectrometer. In this configuration, the trench has been used because a large incident angle is required for surface plasmon resonance excitation. The preliminary results showed that the sensor's performances make it suitable for bio-chemical applications. The easy replacement of the chip allows for the production of an engineered platform by simplifying the measurement procedures.

  2. Characteristics of Recycled Concrete Aggregates from Precast Slab Block Buildings

    Science.gov (United States)

    Venkrbec, Václav; Nováková, Iveta; Henková, Svatava

    2017-10-01

    Precast slab block buildings (PSBB) typically and frequently occur in Central and Eastern Europe, as well as elsewhere in the world. Some of these buildings are currently used beyond their service life capacity. The utilization of recycled materials from these buildings with regard to applying the principles of sustainable construction and using recycled materials will probably be significant in the following years. Documentation from the manufacturing processes of prefabricated blocks for precast slab block buildings is not available, and also it is difficult to declare technological discipline during the construction of these buildings. Therefore, properties of recycled concrete aggregates (RCA) produced from construction and demolition waste (C&DW) of precast slab block buildings build between 1950s to 1990s are not sufficiently known. The demolition of these buildings is very rare today, but it can be assumed an increase in demolitions of these buildings in the future. The use of RCA in new concrete requires verification/testing of the geometrical and physical properties of RCA according to the EN 12 620+A1 standard. The aim of the contribution is to present a case study of the demolition of slab block building with emphasis on RCA usage. The paper presents the results of the tests according to European standards for determining selected geometrical and physical properties of the RCA. The paper describes and evaluates tests such as determination of particle size distribution - Sieve Analysis, content of fine particles, determination of density and water absorption. The results of the properties testing of RCA are compared with the properties of natural aggregate. The general boundary conditions of RCA particular tests are presented.

  3. Development of Flat Slab – Column Interaction with Different Thickness

    OpenAIRE

    Binti Joohari Ilya; Binti Mohd Amin Norliyati

    2017-01-01

    Flat slab – column connection has received much attention in recent years due to its simplicity of construction where beam is not required to support the slab. Flat slab has many usages in the construction field and has been investigated as a potential building material. Despite its many benefits, flat slab is easily subjected to punching shear failure. A simple approach to minimize punching shear failure is by increasing the slab thickness. It is generally accepted that the performance of fl...

  4. Broadband accelerator control network

    International Nuclear Information System (INIS)

    Skelly, J.; Clifford, T.; Frankel, R.

    1983-01-01

    A broadband data communications network has been implemented at BNL for control of the Alternating Gradient Synchrotron (AG) proton accelerator, using commercial CATV hardware, dual coaxial cables as the communications medium, and spanning 2.0 km. A 4 MHz bandwidth Digital Control channel using CSMA-CA protocol is provided for digital data transmission, with 8 access nodes available over the length of the RELWAY. Each node consists of an rf modem and a microprocessor-based store-and-forward message handler which interfaces the RELWAY to a branch line implemented in GPIB. A gateway to the RELWAY control channel for the (preexisting) AGS Computerized Accelerator Operating system has been constructed using an LSI-11/23 microprocessor as a device in a GPIB branch line. A multilayer communications protocol has been defined for the Digital Control Channel, based on the ISO Open Systems Interconnect layered model, and a RELWAY Device Language defined as the required universal language for device control on this channel

  5. Heterogeneous broadband network

    Science.gov (United States)

    Dittmann, Lars

    1995-11-01

    Although the vision for the future Integrated Broadband Communication Network (IBCN) is an all optical network, it is certain that for a long period to come, the network will remain very heterogeneous, with a mixture of different physical media (fiber, coax and twisted pair), transmission systems (PDH, SDH, ADSL) and transport protocols (TCP/IP, AAL/ATM, frame relay). In the current work towards the IBCN, the ATM concept is considered the generic network protocol for both public and private network, with the ability to use different underlying transmission protocols and, through adaptation protocols, provide the appropriate services (old as well as new) to the customer. One of the major difficulties of heterogeneous network is the restriction that is usually given by the lowest common denominator, e.g. in terms of single channel capacity. A possible way to overcome these limitations is by extending the ATM concept with a multilink capability, that allows us to use separate resources as one common. The improved flexibility obtained by this protocol extension further allows a real time optimization of network and call configuration, without any impact on the quality of service seen from the user. This paper describes an example of an ATM based multilink protocol that has been experimentally implemented within the RACE project 'STRATOSPHERIC'. The paper outlines the complexity of introducing an extra network functionality compared with the added value, such as an improved ability to recover an error due to a malfunctioning network component.

  6. Broadband transmission EPR spectroscopy.

    Directory of Open Access Journals (Sweden)

    Wilfred R Hagen

    Full Text Available EPR spectroscopy employs a resonator operating at a single microwave frequency and phase-sensitive detection using modulation of the magnetic field. The X-band spectrometer is the general standard with a frequency in the 9-10 GHz range. Most (biomolecular EPR spectra are determined by a combination of the frequency-dependent electronic Zeeman interaction and a number of frequency-independent interactions, notably, electron spin - nuclear spin interactions and electron spin - electron spin interactions, and unambiguous analysis requires data collection at different frequencies. Extant and long-standing practice is to use a different spectrometer for each frequency. We explore the alternative of replacing the narrow-band source plus single-mode resonator with a continuously tunable microwave source plus a non-resonant coaxial transmission cell in an unmodulated external field. Our source is an arbitrary wave digital signal generator producing an amplitude-modulated sinusoidal microwave in combination with a broadband amplifier for 0.8-2.7 GHz. Theory is developed for coaxial transmission with EPR detection as a function of cell dimensions and materials. We explore examples of a doublet system, a high-spin system, and an integer-spin system. Long, straigth, helical, and helico-toroidal cells are developed and tested with dilute aqueous solutions of spin label hydroxy-tempo. A detection limit of circa 5 µM HO-tempo in water at 800 MHz is obtained for the present setup, and possibilities for future improvement are discussed.

  7. High-resolution investigation of reflections from a deep mantle slab

    Science.gov (United States)

    Schumacher, Lina; Thomas, Christine

    2010-05-01

    Subduction zones form dominant tectonic features on the Earth and it is clear that there is significant three-dimensional structure and complexity within them. Tomographic inversions for P- and S-wave seismic velocities in the Earth's mantle suggest that in several places, subducted oceanic lithosphere descends through the mantle transition zone and penetrates into the lower mantle. But tomography is not able to make a statement concerning structural differences within the slab and its behavior with depth. The main objective of this study is to investigate the geometry, physical parameters and structural differences of subducted slabs by closely investigating seismic P-wave arrivals that reflect off the base of the slab (e.g. the polarity, amplitude, frequency and waveforms of the reflected waves). We are focusing primarily on the Cocos plate that is subducted beneath the Caribbean, since previous migration results show reflections in the slab region from a reflector at the base of the subducted lithosphere. Yet, at that time, a high-resolution investigation of physical parameters was not possible. This is done now by using South American earthquakes recorded by North American networks (e.g. USArray and California broadband seismometers). The data cover a period from 1991-2009 with a minimum magnitude of 5.9 Mw and depths below 100 km. The great circle paths of the source-receiver combinations used here do not intersect the slab and serve as reference. We are looking for reflections from the slab region that would arrive at the stations with different backazimuth. These arrivals can be observed in slowness-backazimuth diagrams as stacked energy of waves traveling out of plane. Information on slowness, backazimuth and travel time is used to backtrack the wave to its reflection point and can be compared to the results of previous migration results and tomography studies. In addition, beamforming for the observed slowness and backazimuth of the out of plane

  8. Cracking behavior of structural slab bridge decks

    Science.gov (United States)

    Baah, Prince

    Bridge deck cracking is a common problem throughout the United States, and it affects the durability and service life of concrete bridges. Several departments of transportation (DOTs) in the United States prefer using continuous three-span solid structural slab bridges without stringers over typical four-lane highways. Recent inspections of such bridges in Ohio revealed cracks as wide as 0.125 in. These measured crack widths are more than ten times the maximum limit recommended in ACI 224R-01 for bridge decks exposed to de-icing salts. Measurements using digital image correlation revealed that the cracks widened under truck loading, and in some cases, the cracks did not fully close after unloading. This dissertation includes details of an experimental investigation of the cracking behavior of structural concrete. Prism tests revealed that the concrete with epoxy-coated bars (ECB) develops the first crack at smaller loads, and develops larger crack widths compared to the corresponding specimens with uncoated (black) bars. Slab tests revealed that the slabs with longitudinal ECB developed first crack at smaller loads, exhibited wider cracks and a larger number of cracks, and failed at smaller ultimate loads compared to the corresponding test slabs with black bars. To develop a preventive measure, slabs with basalt and polypropylene fiber reinforced concrete were also included in the test program. These test slabs exhibited higher cracking loads, smaller crack widths, and higher ultimate loads at failure compared to the corresponding slab specimens without fibers. Merely satisfying the reinforcement spacing requirements given in AASHTO or ACI 318-11 is not adequate to limit cracking below the ACI 224R-01 recommended maximum limit, even though all the relevant design requirements are otherwise met. Addition of fiber to concrete without changing any steel reinforcing details is expected to reduce the severity and extent of cracking in reinforced concrete bridge decks.

  9. Driving demand for broadband networks and services

    CERN Document Server

    Katz, Raul L

    2014-01-01

    This book examines the reasons why various groups around the world choose not to adopt broadband services and evaluates strategies to stimulate the demand that will lead to increased broadband use. It introduces readers to the benefits of higher adoption rates while examining the progress that developed and emerging countries have made in stimulating broadband demand. By relying on concepts such as a supply and demand gap, broadband price elasticity, and demand promotion, this book explains differences between the fixed and mobile broadband demand gap, introducing the notions of substitution and complementarity between both platforms. Building on these concepts, ‘Driving Demand for Broadband Networks and Services’ offers a set of best practices and recommendations aimed at promoting broadband demand.  The broadband demand gap is defined as individuals and households that could buy a broadband subscription because they live in areas served by telecommunications carriers but do not do so because of either ...

  10. Accidents due to falls from roof slabs.

    Science.gov (United States)

    Rudelli, Bruno Alves; Silva, Marcelo Valerio Alabarce da; Akkari, Miguel; Santili, Claudio

    2013-01-01

    CONTEXT AND OBJECTIVE Falls from the roof slabs of houses are accidents of high potential severity that occur in large Brazilian cities and often affect children and adolescents. The aims of this study were to characterize the factors that predispose towards this type of fall involving children and adolescents, quantify the severity of associated lesions and suggest preventive measures. DESIGN AND SETTING Descriptive observational prospective longitudinal study in two hospitals in the metropolitan region of São Paulo. METHODS Data were collected from 29 cases of falls from roof slabs involving children and adolescents between October 2008 and October 2009. RESULTS Cases involving males were more prevalent, accounting for 84%. The predominant age group was schoolchildren (7 to 12 years old; 44%). Leisure activities were most frequently being practiced on the roof slab at the time of the fall (86%), and flying a kite was the most prevalent game (37.9%). In 72% of the cases, the children were unaccompanied by an adult responsible for them. Severe conditions such as multiple trauma and traumatic brain injuries resulted from 79% of the accidents. CONCLUSION Falls from roof slabs are accidents of high potential severity, and preventive measures aimed towards informing parents and guardians about the dangers and risk factors associated with this type of accident are needed, along with physical protective measures, such as low walls around the slab and gates with locks to restrict free access to these places.

  11. Accidents due to falls from roof slabs

    Directory of Open Access Journals (Sweden)

    Bruno Alves Rudelli

    Full Text Available CONTEXT AND OBJECTIVE Falls from the roof slabs of houses are accidents of high potential severity that occur in large Brazilian cities and often affect children and adolescents. The aims of this study were to characterize the factors that predispose towards this type of fall involving children and adolescents, quantify the severity of associated lesions and suggest preventive measures. DESIGN AND SETTING Descriptive observational prospective longitudinal study in two hospitals in the metropolitan region of São Paulo. METHODS Data were collected from 29 cases of falls from roof slabs involving children and adolescents between October 2008 and October 2009. RESULTS Cases involving males were more prevalent, accounting for 84%. The predominant age group was schoolchildren (7 to 12 years old; 44%. Leisure activities were most frequently being practiced on the roof slab at the time of the fall (86%, and flying a kite was the most prevalent game (37.9%. In 72% of the cases, the children were unaccompanied by an adult responsible for them. Severe conditions such as multiple trauma and traumatic brain injuries resulted from 79% of the accidents. CONCLUSION Falls from roof slabs are accidents of high potential severity, and preventive measures aimed towards informing parents and guardians about the dangers and risk factors associated with this type of accident are needed, along with physical protective measures, such as low walls around the slab and gates with locks to restrict free access to these places.

  12. Influence of slab length on dynamic characteristics of subway train-steel spring floating slab track-tunnel coupled system

    Directory of Open Access Journals (Sweden)

    Qing-yuan Xu

    Full Text Available A subway train-steel spring floating slab track-tunnel coupling dynamic model, considering short and middle-long wavelength random track irregularities, and longitudinal connection between adjacent slabs of steel spring floating slab track, was developed. And the influence of slab length on dynamic characteristics of the system under different track conditions and train speeds are theoretically studied. The calculated results show: (1 In general, the acceleration of each component of the coupled system decreases with the increase of slab length under the perfectly smooth track condition; (2 Slab length has different influence laws on acceleration of each component of subway train-steel spring floating slab track-tunnel coupled system under random irregularity of track condition. The lower the dominant frequency distribution of vibration acceleration is, the higher influence slab length has; (3 With the increase of slab length, the force of rail, fastener and steel spring also decreases significantly, which helps to lengthen the service life of these components; (4 With the increase of slab length, the longitudinal bending moment of slab increases sharply at first, then it begins to drop slightly. When slab length exceeds the distance between two bogies of a vehicle, the longitudinal bending moment of slab changes little; (5 Slab length has significant influence on the dynamic force and displacement of the coupled system when train speed is higher.

  13. Slab tears and intermediate-depth seismicity

    Science.gov (United States)

    Meighan, Hallie E.; ten Brink, Uri S.; Pulliam, Jay

    2013-01-01

    Active tectonic regions where plate boundaries transition from subduction to strike slip can take several forms, such as triple junctions, acute, and obtuse corners. Well-documented slab tears that are associated with high rates of intermediate-depth seismicity are considered here: Gibraltar arc, the southern and northern ends of the Lesser Antilles arc, and the northern end of Tonga trench. Seismicity at each of these locations occurs, at times, in the form of swarms or clusters, and various authors have proposed that each marks an active locus of tear propagation. The swarms and clusters start at the top of the slab below the asthenospheric wedge and extend 30–60 km vertically downward within the slab. We propose that these swarms and clusters are generated by fluid-related embrittlement of mantle rocks. Focal mechanisms of these swarms generally fit the shear motion that is thought to be associated with the tearing process.

  14. Analysis of broadband aerodynamic noise from VS45

    Energy Technology Data Exchange (ETDEWEB)

    Dundabin, P. [Renewable Energy Systems Ltd., Glasgow, Scotland (United Kingdom)

    1997-12-31

    This paper describes the analysis of acoustic data taken from the VS45 at Kaiser-Wilhelm-Koog. The aim was to investigate the dependence of aerodynamic noise on tip speed and angle of attack. In particular, the dependence of noise in individual third octave bands on these variable is examined. The analysis is divided into 3 sections: data selection, data checks and analysis of broadband nacelle noise; analysis of broadband aerodynamic noise and its sensitivity to tip speed and angle of attack. (LN)

  15. Imaging subducted slabs using seismic arrays in the Western Pacific

    Science.gov (United States)

    Bentham, H. L.; Rost, S.

    2010-12-01

    In recent years array seismology has been used extensively to image the small scale structure of the Earth. Such structure likely represents chemical heterogeneity and is therefore essential in our understanding of mantle convection and the composition of the Earth’s deep interior. As subduction is the main source of (re)introducing slab material into the Earth, it is of particular interest to track these heterogeneities. Resolving details of the composition and deformation of subducted lithosphere can help provide constraints on the subduction process, the composition of the mantle and mantle convection. This study uses seismic array techniques to map seismic heterogeneities associated with western Pacfic subduction zones, where a variety of slab geometries have been previously observed. Seismic energy arriving prior to the PP arrival was analysed at Eielson Array (ILAR), Alaska. More than 200 earthquakes were selected with Mw ≥ 6 and with epicentral distances of 90-110deg, giving a good coverage of the PP precursor (P*P) wavefield. Initial findings indicate that the observed P*P arrive out of plane and are likely a result of scattering. These scatterers are linked to the subduction of the Pacific Plate under the Philippine Sea in the Izu-Bonin and Mariana subduction zones. To enable efficient processing of large datasets, a robust automatic coherent (but unpredicted) arrival detector algorithm has been developed to select suitable precursors. Slowness and backazimuth were calculated for each precursor and were used in conjunction with P*P arrival times to back-raytrace the energy from the array to the scatterer location. Processing of the full dataset will help refine models regarding slab deformation as they descend into the mantle as well as unveiling the depth of their descent.

  16. Entropy distribution in accelerated gaseous slabs

    International Nuclear Information System (INIS)

    Thomas, L.P.; Diez, J.A.

    1990-01-01

    Shocks developed in an accelerated plane layer of ideal gas are studied. The layer is driven towards vacuum by an ideal rigid piston. There can be an intermediate solid slab between the gas and the piston. It gives to the slabs a stepwise pressure pulse with or without prepulse. The shock compressions build up non-uniform profiles in the gas. Explicit analytical expressions for the Lagrangian distribution of entropy are found. Then, the width of innermost part of the gas with higher specific entropy was obtained. These results are of interest to regulate the spark formation parameters in ICF experiments. (Author)

  17. Behaviour of reinforced concrete slabs with steel fibers

    Science.gov (United States)

    Baarimah, A. O.; Syed Mohsin, S. M.

    2017-11-01

    This paper investigates the potential effect of steel fiber added into reinforced concrete slabs. Four-point bending test is conducted on six slabs to investigate the structural behaviour of the slabs by considering two different parameters; (i) thickness of slab (ii) volume fraction of steel fiber. The experimental work consists of six slabs, in which three slabs are designed in accordance to Eurocode 2 to fulfil shear capacity characteristic, whereas, the other three slabs are designed with 17% less thickness, intended to fail in shear. Both series of slabs are added with steel fiber with a volume fraction of Vf = 0%, Vf = 1% and Vf = 2% in order to study the effect and potential of fiber to compensate the loss in shear capacity. The slab with Vf = 0% steel fiber and no reduction in thickness is taken as the control slab. The experimental result suggests promising improvement of the load carrying capacity (up to 32%) and ductility (up to 87%) as well as delayed in crack propagation for the slabs with Vf = 2%. In addition, it is observed that addition of fibers compensates the reduction in the slab thickness as well as changes the failure mode of the slab from brittle to a more ductile manner.

  18. Observations involving broadband impedance modelling

    International Nuclear Information System (INIS)

    Berg, J.S.

    1995-08-01

    Results for single- and multi-bunch instabilities can be significantly affected by the precise model that is used for the broadband impendance. This paper discusses three aspects of broadband impendance modeling. The first is an observation of the effect that a seemingly minor change in an impedance model has on the single-bunch mode coupling threshold. The second is a successful attempt to construct a model for the high-frequency tails of an r.f cavity. The last is a discussion of requirements for the mathematical form of an impendance which follow from the general properties of impendances

  19. Observations involving broadband impedance modelling

    Energy Technology Data Exchange (ETDEWEB)

    Berg, J.S. [Stanford Linear Accelerator Center, Menlo Park, CA (United States)

    1996-08-01

    Results for single- and multi-bunch instabilities can be significantly affected by the precise model that is used for the broadband impedance. This paper discusses three aspects of broadband impedance modelling. The first is an observation of the effect that a seemingly minor change in an impedance model has on the single-bunch mode coupling threshold. The second is a successful attempt to construct a model for the high-frequency tails of an r.f. cavity. The last is a discussion of requirements for the mathematical form of an impedance which follow from the general properties of impedances. (author)

  20. Organic-inorganic broadband photodetector

    Science.gov (United States)

    Yang, Xianguang; Li, Baojun

    2018-01-01

    The capability to detect optical signals over a broad wavelength band is highly important for practical device applications. However, high speed responsive across entire wavelength band within a single photodetector remains challenge. Here we demonstrated a broadband photodetector using a single quantum-dot-doped polyaniline nanowire with a broadband responsive at 350-700 nm (see schematic). The high responsivity is attributed to the high density of trapping states at the enormous interfaces formed in polyaniline and quantum dots. The interface trapping can effectively reduce the recombination rate, promote the separation of photogenerated carriers, and then enhance the efficiency for optical detection.

  1. The slab geometry laser. II - Thermal effects in a finite slab

    Science.gov (United States)

    Kane, T. J.; Byer, R. L.; Eggleston, J. M.

    1985-01-01

    This paper presents two methods for calculating the thermally induced stress, focusing, and depolarization in a pumped zigzag-slab solid-state laser. A computer program capable of detailed calculations of thermal effects in the general case is described. An approximate analysis of slab thermal effects in many cases allows calculation of these effects without use of the computer model directly. The analysis predicts that slabs of square cross section can be designed to have low depolarization and thermal focusing compared to Nd:YAG laser rods.

  2. 75 FR 3791 - Broadband Technology Opportunities Program

    Science.gov (United States)

    2010-01-22

    ... broadband capacity at public computer centers, and promoting sustainable broadband adoption projects. In... from BTOP for public computer center projects. In addition, parties filed more than 320 applications... projects; $15.9 million for Public Computer Center projects; and $2.4 million for Sustainable Broadband...

  3. Reinforcement of the concrete base slab of the ATLAS cavern

    CERN Multimedia

    Maximilien Brice

    2002-01-01

    Photo 02: UX15 cavern, preparation for concreting of base slab first lift. Photo 05: UX15 cavern, placing of reinforcement for base slab first lift. Photo 07: UX15 cavern, preparation for concreting of base slab first lift. Photo 09: UX15 cavern, placing of reinforcement for base slab first lift. Photo 10: UX15 cavern, view into PX14 shaft above. Photo 12: UX15 cavern, temporary access platform of RB16 tunnel. Photo 15: UJ17 chamber, invert excavation.

  4. The need and benefit of slab track: case of Lithuania

    OpenAIRE

    Gailienė, Inesa; Laurinavičius, Alfredas

    2017-01-01

    Slab track structures have been used in the world for several decades now. However, the ballasted track is still much more popular compared to slab track structures, which is primarily due to its lower price. This article reviews and analyses development of slab tracks, with their advantages and disadvantages. Based on conditions prevailing on Lithuanian railways, the paper also distinguishes cases in which slab track structures could be of benefit, both economically and technologically. The ...

  5. Cost analysis of reinforced concrete slabs and columns

    OpenAIRE

    Spuś, Piotr

    2013-01-01

    The construction industry is increasingly looking for solutions that are both simple and effective and that provide cost savings, speed and flexibility of execution. Two-way slabs are a form of construction unique to reinforced concrete comparing with the other major structural materials. It is an efficient, economical, and widely used structural system. The present dissertation aims to analyze and compare costs between four types of slabs: waffle slab with recuperate molds, flat slabs wit...

  6. Achieving universal access to broadband

    DEFF Research Database (Denmark)

    Falch, Morten; Henten, Anders

    2009-01-01

    The paper discusses appropriate policy measures for achieving universal access to broadband services in Europe. Access can be delivered by means of many different technology solutions described in the paper. This means a greater degree of competition and affects the kind of policy measures...

  7. Lifetime Reliability Assessment of Concrete Slab Bridges

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle

    A procedure for lifetime assesment of the reliability of short concrete slab bridges is presented in the paper. Corrosion of the reinforcement is the deterioration mechanism used for estimating the reliability profiles for such bridges. The importance of using sensitivity measures is stressed...

  8. Scattering by a slab: an exact calculation

    Czech Academy of Sciences Publication Activity Database

    Bentosela, F.; Tater, Miloš

    2005-01-01

    Roč. 38, č. 22 (2005), s. 4835-4841 ISSN 0305-4470 R&D Projects: GA AV ČR IAA100480501 Institutional research plan: CEZ:AV0Z10480505 Keywords : scattering by a slab Subject RIV: BE - Theoretical Physics Impact factor: 1.566, year: 2005

  9. All-polymer photonic crystal slab sensor

    DEFF Research Database (Denmark)

    Hermannsson, Pétur Gordon; Sørensen, Kristian Tølbøl; Vannahme, Christoph

    2015-01-01

    An all-polymer photonic crystal slab sensor is presented, and shown to exhibit narrow resonant reflection with a FWHM of less than 1 nm and a sensitivity of 31 nm/RIU when sensing media with refractive indices around that of water. This results in a detection limit of 4.5x10-6 RIU when measured i...

  10. Numerical Evaluations of Functionally Graded RC Slabs

    Directory of Open Access Journals (Sweden)

    M. Mastali

    2014-01-01

    Full Text Available Nowadays, using fibrous materials is used widely in strengthening applications such as cross-section enlargement and using functionally graded reinforced concrete. Functionally graded reinforced concrete is used as multireinforced concrete layers that can be reinforced by different fiber types. The objective of this research was to address the structural benefits of functionally graded concrete materials by performing analytical simulations. In order to achieve this purpose, in the first stage of this study, three functionally graded reinforced concretes by steel and polypropylene (PP were experimentally tested under flexural loading. Inverse analysis was applied to obtain the used material properties of reinforced concrete by FEMIX software. After obtaining the material properties, to assess the performance of proposed slabs, some other cases were proposed and numerically evaluated under flexural and shear loading. The results showed that increasing steel fiber in reinforced entire cross section led to achieve better shear and flexural performance while the best performance of reinforced functionally graded slabs was achieved for slab at 1% fiber content. In the second stage, nineteen reinforced functionally graded RC slabs with steel bars were simulated and assessed and some other cases were considered which were not experimentally tested.

  11. Development Length for Headed Bars in Slab-Column Joints of RC Slab Bridges

    Science.gov (United States)

    2015-12-04

    In accordance with the Caltrans Seismic Design Criteria, the superstructure in a slab bridge should remain essentially elastic and only the pile extensions/columns are permitted to develop inelastic deformations during a seismic event. Hence, the lon...

  12. Slab albedo for linearly and quadratically anisotropic scattering kernel with modified F{sub N} method

    Energy Technology Data Exchange (ETDEWEB)

    Tuereci, R. Goekhan [Kirikkale Univ. (Turkey). Kirikkale Vocational School; Tuereci, D. [Ministry of Education, Ankara (Turkey). 75th year Anatolia High School

    2017-11-15

    One speed, time independent and homogeneous medium neutron transport equation is solved with the anisotropic scattering which includes both the linearly and the quadratically anisotropic scattering kernel. Having written Case's eigenfunctions and the orthogonality relations among of these eigenfunctions, slab albedo problem is investigated as numerically by using Modified F{sub N} method. Selected numerical results are presented in tables.

  13. Modified bond model for shear in slabs under concentrated loads

    NARCIS (Netherlands)

    Lantsoght, E.O.L.; Van der Veen, C.; De Boer, A.

    2015-01-01

    Slabs subjected to concentrated loads close to supports, as occurring for truck loads on slab bridges, are less studied than beams in shear or slab-column connections in punching. To predict the shear capacity for this case, the Bond Model for concentric punching shear was studied initially.

  14. Control of exceptional points in photonic crystal slabs

    DEFF Research Database (Denmark)

    Kaminski, Piotr Marek; Taghizadeh, Alireza; Breinbjerg, Olav

    2017-01-01

    Various ways of controlling the extent of the ring of exceptional points in photonic crystal slabs are investigated. The extent of the ring in photonic crystal slabs is found to vary with the thickness of the slab. This enables recovery of Dirac cones in open, non-Hermitian systems, such as a pho...

  15. Slab detachment of subducted Indo-Australian plate beneath Sunda ...

    Indian Academy of Sciences (India)

    ... complicate the subduction zone processes and slab architecture. Based on evidences which include patterns of seismicity, seismic tomography and geochemistry of arc volcanoes, we have identified a horizontal slab tear in the subducted Indo-Australian slab beneath the Sunda arc. It strongly reflects on trench migration, ...

  16. Air slab-correction for Γ-ray attenuation measurements

    Science.gov (United States)

    Mann, Kulwinder Singh

    2017-12-01

    Gamma (γ)-ray shielding behaviour (GSB) of a material can be ascertained from its linear attenuation coefficient (μ, cm-1). Narrow-beam transmission geometry is required for μ-measurement. In such measurements, a thin slab of the material has to insert between point-isotropic γ-ray source and detector assembly. The accuracy in measurements requires that sample's optical thickness (OT) remain below 0.5 mean free path (mfp). Sometimes it is very difficult to produce thin slab of sample (absorber), on the other hand for thick absorber, i.e. OT >0.5 mfp, the influence of the air displaced by it cannot be ignored during μ-measurements. Thus, for a thick sample, correction factor has been suggested which compensates the air present in the transmission geometry. The correction factor has been named as an air slab-correction (ASC). Six samples of low-Z engineering materials (cement-black, clay, red-mud, lime-stone, cement-white and plaster-of-paris) have been selected for investigating the effect of ASC on μ-measurements at three γ-ray energies (661.66, 1173.24, 1332.50 keV). The measurements have been made using point-isotropic γ-ray sources (Cs-137 and Co-60), NaI(Tl) detector and multi-channel-analyser coupled with a personal computer. Theoretical values of μ have been computed using a GRIC2-toolkit (standardized computer programme). Elemental compositions of the samples were measured with Wavelength Dispersive X-ray Fluorescence (WDXRF) analyser. Inter-comparison of measured and computed μ-values, suggested that the application of ASC helps in precise μ-measurement for thick samples of low-Z materials. Thus, this hitherto widely ignored ASC factor is recommended to use in similar γ-ray measurements.

  17. Investigation of complete bandgaps in a piezoelectric slab covered with periodically structured coatings.

    Science.gov (United States)

    Zou, Kui; Ma, Tian-Xue; Wang, Yue-Sheng

    2016-02-01

    The propagation of elastic waves in a piezoelectric slab covered with periodically structured coatings or the so-called stubbed phononic crystal slab is investigated. Four different models are selected and the effects of distribution forms and geometrical parameters of the structured coatings on complete bandgaps are discussed. The phononic crystal slab with symmetric coatings can generate wider complete bandgaps while that with asymmetric coatings is favorable for the generation of multi-bandgaps. The complete bandgaps, which are induced by locally resonant effects, change significantly as the geometry of the coatings changes. Moreover, the piezoelectric effects benefit the opening of the complete bandgaps. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. Two-group Analysis of Xenon Stability in Slab Geometry by Modal Expansion

    International Nuclear Information System (INIS)

    Norinder, O.

    1963-05-01

    Xenon spatial stability is analyzed with the flux represented by two neutron energy groups. General formulas are given for expansions in a system of modes. Detailed formulas are recorded for a slab described by sinusoidal modes. A short description is given of a Mercury Autocode program for numerical calculations in slab geometry. The essential input parameters and results are noted for 80 computed cases. The main body of the calculations were intended to clarify the xenon stability properties of the Marviken reactor, which was found to have a sufficient margin against unstable xenon oscillations. The neutron flux detection and the control rod insertion in the slab were found to have a large influence on the stability in spite of the nonexistence of space-selective control in the systems investigated. Very good agreement was found between stability limits calculated according to Randall and St. John and stability limits calculated by the program

  19. Influence of slab length on dynamic characteristics of subway train-steel spring floating slab track-tunnel coupled system

    OpenAIRE

    Xu, Qing-yuan; Yan, Bin; Lou, Ping; Zhou, Xiao-lin

    2015-01-01

    A subway train-steel spring floating slab track-tunnel coupling dynamic model, considering short and middle-long wavelength random track irregularities, and longitudinal connection between adjacent slabs of steel spring floating slab track, was developed. And the influence of slab length on dynamic characteristics of the system under different track conditions and train speeds are theoretically studied. The calculated results show: (1) In general, the acceleration of each component of the cou...

  20. Visible light broadband perfect absorbers

    Energy Technology Data Exchange (ETDEWEB)

    Jia, X. L.; Meng, Q. X.; Yuan, C. X.; Zhou, Z. X.; Wang, X. O., E-mail: wxo@hit.edu.cn [School of Science, Harbin Institute of Technology, Harbin 150001 (China)

    2016-03-15

    The visible light broadband perfect absorbers based on the silver (Ag) nano elliptical disks and holes array are studied using finite difference time domain simulations. The semiconducting indium silicon dioxide thin film is introduced as the space layer in this sandwiched structure. Utilizing the asymmetrical geometry of the structures, polarization sensitivity for transverse electric wave (TE)/transverse magnetic wave (TM) and left circular polarization wave (LCP)/right circular polarization wave (RCP) of the broadband absorption are gained. The absorbers with Ag nano disks and holes array show several peaks absorbance of 100% by numerical simulation. These simple and flexible perfect absorbers are particularly desirable for various potential applications including the solar energy absorber.

  1. Color discrimination with broadband photoreceptors.

    Science.gov (United States)

    Schnaitmann, Christopher; Garbers, Christian; Wachtler, Thomas; Tanimoto, Hiromu

    2013-12-02

    Color vision is commonly assumed to rely on photoreceptors tuned to narrow spectral ranges. In the ommatidium of Drosophila, the four types of so-called inner photoreceptors express different narrow-band opsins. In contrast, the outer photoreceptors have a broadband spectral sensitivity and were thought to exclusively mediate achromatic vision. Using computational models and behavioral experiments, we demonstrate that the broadband outer photoreceptors contribute to color vision in Drosophila. The model of opponent processing that includes the opsin of the outer photoreceptors scored the best fit to wavelength discrimination data. To experimentally uncover the contribution of individual photoreceptor types, we restored phototransduction of targeted photoreceptor combinations in a blind mutant. Dichromatic flies with only broadband photoreceptors and one additional receptor type can discriminate different colors, indicating the existence of a specific output comparison of the outer and inner photoreceptors. Furthermore, blocking interneurons postsynaptic to the outer photoreceptors specifically impaired color but not intensity discrimination. Our findings show that receptors with a complex and broad spectral sensitivity can contribute to color vision and reveal that chromatic and achromatic circuits in the fly share common photoreceptors. Copyright © 2013 Elsevier Ltd. All rights reserved.

  2. Novel Radon Sub-Slab Suctioning System

    DEFF Research Database (Denmark)

    Rasmussen, Torben Valdbjørn

    2013-01-01

    A new principle for radon protection is currently presented which makes use of a system of horizontal pressurised air ducts located within the lower part of the rigid insulation layer of the ground-floor slab. The function of this system is based on the principles of pressure reduction within...... a grid of horizontal air ducts with low pressure which are able to remove air and radon from the ground. Results showed the system to be effective in preventing radon infiltrating from the ground through the ground-floor slab, avoiding high concentrations of radon being accumulated inside houses....... For the system to be effective, the pressure within the ducts must be lower than the pressure inside the house. The new principle was shown to be effective in preventing radon from polluting the indoor air by introducing low pressure in the horizontal grid of air ducts. A lower pressure than the pressure inside...

  3. Fast Waves in Smooth Coronal Slab

    Science.gov (United States)

    Lopin, I.; Nagorny, I.

    2015-03-01

    This work investigates the effect of transverse density structuring in coronal slab-like waveguides on the properties of fast waves. We generalized previous results obtained for the exponential and Epstein profiles to the case of an arbitrary transverse density distribution. The criteria are given to determine the possible (trapped or leaky) wave regime, depending on the type of density profile function. In particular, there are plasma slabs with transverse density structuring that support pure trapped fast waves for all wavelengths. Their phase speed is nearly equal to the external Alfvén speed for the typical parameters of coronal loops. Our findings are obtained on the basis of Kneser’s oscillation theorem. To confirm the results, we analytically solved the wave equation evaluated at the cutoff point and the original wave equation for particular cases of transverse density distribution. We also used the WKB method and obtained approximate solutions of the wave equation at the cutoff point for an arbitrary transverse density profile. The analytic results were supplemented by numerical solutions of the obtained dispersion relations. The observed high-quality quasi-periodic pulsations of flaring loops are interpreted in terms of the trapped fundamental fast-sausage mode in a slab-like coronal waveguide.

  4. Security for Telecommuting and Broadband Communications: Recommendations of the National Institute of Standards and Technology

    Science.gov (United States)

    Kuhn, D. R.; Tracy, Miles C.; Frankel, Sheila E.

    2002-08-01

    This document is intended to assist those responsible - users, system administrators, and management - for telecommuting security, by providing introductory information about broadband communication security and policy, security of home office systems, and considerations for system administrators in the central office. It addresses concepts relating to the selection, deployment, and management of broadband communications for a telecommuting user. This document is not intended to provide a mandatory framework for telecommuting or home office broadband communication environments, but rather to present suggested approaches to the topic.

  5. Analysis of the Proposed Ghana Broadband Strategy

    DEFF Research Database (Denmark)

    Williams, Idongesit; Botwe, Yvonne

    This project studied the Ghana Broadband Strategy with the aim of evaluating the recommendations in the strategy side by side the broadband development in Ghana. The researchers conducted interviews both officially and unofficially with ICT stakeholders, made observations, studied Government...... intervention policies recommended in the Ghana broadband policy is used to evaluate the broadband market to find out whether the strategy consolidates with the Strengths and opportunities of the market and whether it corrects the anomalies that necessitate the weaknesses and threats to the market....... The strategy did address some threats and weaknesses of the broadband market. It also consolidated on some strengths and opportunities of the broadband market. The researchers also discovered that a market can actually grow without a policy. But a market will grow faster if a well implemented policy is guiding...

  6. Viscous Dissipation and Criticality of Subducting Slabs

    Science.gov (United States)

    Riedel, Mike; Karato, Shun; Yuen, Dave

    2016-04-01

    Rheology of subducting lithosphere appears to be complicated. In the shallow part, deformation is largely accomodated by brittle failure, whereas at greater depth, at higher confining pressures, ductile creep is expected to control slab strength. The amount of viscous dissipation ΔQ during subduction at greater depth, as constrained by experimental rock mechanics, can be estimated on the basis of a simple bending moment equation [1,2] 2ɛ˙0(z) ∫ +h/2 2 M (z) = h ṡ -h/2 4μ(y,z)y dy , (1) for a complex multi-phase rheology in the mantle transition zone, including the effects of a metastable phase transition as well as the pressure, temperature, grain-size and stress dependency of the relevant creep mechanisms; μ is here the effective viscosity and ɛ˙0(z) is a (reference) strain rate. Numerical analysis shows that the maximum bending moment, Mcrit, that can be sustained by a slab is of the order of 1019 Nm per m according to Mcrit˜=σp ∗h2/4, where σp is the Peierl's stress limit of slab materials and h is the slab thickness. Near Mcrit, the amount of viscous dissipation grows strongly as a consequence of a lattice instability of mantle minerals (dislocation glide in olivine), suggesting that thermo-mechanical instabilities become prone to occur at places where a critical shear-heating rate is exceeded, see figure. This implies that the lithosphere behaves in such cases like a perfectly plastic solid [3]. Recently available detailed data related to deep seismicity [4,5] seems to provide support to our conclusion. It shows, e.g., that thermal shear instabilities, and not transformational faulting, is likely the dominating mechanism for deep-focus earthquakes at the bottom of the transition zone, in accordance with this suggested "deep criticality" model. These new findings are therefore briefly outlined and possible implications are discussed. References [1] Riedel, M. R., Karato, S., Yuen, D. A. Criticality of Subducting Slabs. University of Minnesota

  7. Detecting slab structure beneath the Banda Arc from waveform analysis of deep focus earthquakes

    Science.gov (United States)

    Miller, M. S.; Sun, D.; Holt, A. F.

    2017-12-01

    We investigate the structure of the subducting Australian slab by utilizing 30 recently installed, temporary broadband seismometers (YS network) in the Banda Arc region of the Indonesia archipelago. This region is of particular tectonic interest as it is the archetypal example of a young arc-continent collision along with known varied lithospheric structure of the incoming Australian plate. Previous (e.g. Widiyantoro et al. 2011) and preliminary body wave tomography (Harris et al., this session) indicate complex subducted slab structures, where gaps in fast velocity anomalies in the upper mantle are interpreted as slab tears and are linked to the variation in the incoming plate structures. The detailed shape and location of these tears are important for kinematic reconstructions and for understanding the evolution of the entire subduction system. However, tomographic images are inherently smooth due to being produced with damped inversions and therefore underestimate the sharpness of these structures. We investigate possible sharp-sided structures within and at the edges of the subducted plate from deep focus earthquakes beneath the Banda Arc that occur beneath the seismic stations. Preliminary results show that the energy associated with the P-wave first arrival exhibits large variability between waveforms recorded at different stations along the arc, both in terms of frequency content and maximum amplitudes. Three main observations are shown with these initial results: (i) Variation in frequency content along strike from the deep events; (ii) There are two "regions" that have low frequency signals which possibly correspond to subducted continental lithosphere; (iii) There are two "regions" that have high frequency signals which possibly correspond to subducted oceanic lithosphere.

  8. Principles of broadband switching and networking

    CERN Document Server

    Liew, Soung C

    2010-01-01

    An authoritative introduction to the roles of switching and transmission in broadband integrated services networks Principles of Broadband Switching and Networking explains the design and analysis of switch architectures suitable for broadband integrated services networks, emphasizing packet-switched interconnection networks with distributed routing algorithms. The text examines the mathematical properties of these networks, rather than specific implementation technologies. Although the pedagogical explanations in this book are in the context of switches, many of the fundamenta

  9. Processing and properties of large-sized ceramic slabs

    Directory of Open Access Journals (Sweden)

    Fossa, L.

    2010-10-01

    Full Text Available Large-sized ceramic slabs – with dimensions up to 360x120 cm2 and thickness down to 2 mm – are manufactured through an innovative ceramic process, starting from porcelain stoneware formulations and involving wet ball milling, spray drying, die-less slow-rate pressing, a single stage of fast drying-firing, and finishing (trimming, assembling of ceramic-fiberglass composites. Fired and unfired industrial slabs were selected and characterized from the technological, compositional (XRF, XRD and microstructural (SEM viewpoints. Semi-finished products exhibit a remarkable microstructural uniformity and stability in a rather wide window of firing schedules. The phase composition and compact microstructure of fired slabs are very similar to those of porcelain stoneware tiles. The values of water absorption, bulk density, closed porosity, functional performances as well as mechanical and tribological properties conform to the top quality range of porcelain stoneware tiles. However, the large size coupled with low thickness bestow on the slab a certain degree of flexibility, which is emphasized in ceramic-fiberglass composites. These outstanding performances make the large-sized slabs suitable to be used in novel applications: building and construction (new floorings without dismantling the previous paving, ventilated façades, tunnel coverings, insulating panelling, indoor furnitures (table tops, doors, support for photovoltaic ceramic panels.

    Se han fabricado piezas de gran formato, con dimensiones de hasta 360x120 cm, y menos de 2 mm, de espesor, empleando métodos innovadores de fabricación, partiendo de composiciones de gres porcelánico y utilizando, molienda con bolas por vía húmeda, atomización, prensado a baja velocidad sin boquilla de extrusión, secado y cocción rápido en una sola etapa, y un acabado que incluye la adhesión de fibra de vidrio al soporte cerámico y el rectificado de la pieza final. Se han

  10. Evidence of fire resistance of hollow-core slabs

    DEFF Research Database (Denmark)

    Hertz, Kristian Dahl; Sørensen, Lars Schiøtt; Giuliani, Luisa

    Hollow-core slabs have during the past 50 years comprised a variety of different structures with different cross-sections and reinforcement. At present the extruded hollow-core slabs without cross-reinforcement in the bottom flange and usually round or oval longitudinal channels (holes) are predo......Hollow-core slabs have during the past 50 years comprised a variety of different structures with different cross-sections and reinforcement. At present the extruded hollow-core slabs without cross-reinforcement in the bottom flange and usually round or oval longitudinal channels (holes....... The present paper analyses the evidence now available for assessment of the fire resistance of extruded hollow-core slabs. The 162 fire tests from the Holcofire report are compared against the requirements for testing from the product standard for hollow-core slabs EN1168 and knowledge about the possible...

  11. A STUDY ON THE WHEELSET/SLAB TRACK VERTICAL INTERACTION

    Directory of Open Access Journals (Sweden)

    Traian MAZILU

    2012-05-01

    Full Text Available This paper deals with the interaction between a moving wheelset and a slab track due to the short-pitch corrugated rail. The wheelset is modeled using a free-free Timoshenko beam with attached rigid bodies as the axle boxes, wheels and brake discs. The slab track model consists of elastically supported double Euler-Bernoulli beams. In fact, both wheelset and slab track are symmetric structures and the issue of the wheelset/slab track interaction is reduced to the wheel/rail interaction. The nonlinear equations of motion describing the wheelset/slab track interaction due to the short-pitch corrugated rail are solved using the time-domain Green’s functions method and the convolution theorem. The wheelset/slab track interaction due to the short-pitch corrugated rail exhibits a critical velocity when the vibration reaches the maximum level

  12. Understanding broadband over power line

    CERN Document Server

    Held, Gilbert

    2006-01-01

    Understanding Broadband over Power Line explores all aspects of the emerging technology that enables electric utilities to provide support for high-speed data communications via their power infrastructure. This book examines the two methods used to connect consumers and businesses to the Internet through the utility infrastructure: the existing electrical wiring of a home or office; and a wireless local area network (WLAN) access point.Written in a practical style that can be understood by network engineers and non-technologists alike, this volume offers tutorials on electric utility infrastru

  13. Achieving Universal Access to Broadband

    Directory of Open Access Journals (Sweden)

    Morten FALCH

    2009-01-01

    Full Text Available The paper discusses appropriate policy measures for achieving universal access to broadband services in Europe. Access can be delivered by means of many different technology solutions described in the paper. This means a greater degree of competition and affects the kind of policy measures to be applied. The paper concludes that other policy measure than the classical universal service obligation are in play, and discusses various policy measures taking the Lisbon process as a point of departure. Available policy measures listed in the paper include, universal service obligation, harmonization, demand stimulation, public support for extending the infrastructure, public private partnerships (PPP, and others.

  14. POTS to broadband ... cable modems.

    Science.gov (United States)

    Kabachinski, Jeff

    2003-01-01

    There have been 3 columns talking about broadband communications and now at the very end when it's time to compare using a telco or cableco, I'm asking does it really matter? So what if I can actually get the whole 30 Mbps with a cable network when the website I'm connecting to is running on an ISDN line at 128 Kbps? Broadband offers a lot more bandwidth than the connections many Internet servers have today. Except for the biggest websites, many servers connect to the Internet with a switched 56-Kbps, ISDN, or fractional T1 line. Even with the big websites, my home network only runs a 10 Mbps Ethernet connection to my cable modem. Maybe it doesn't matter that the cable lines are shared or that I can only get 8 Mbps from an ADSL line. Maybe the ISP that I use has a T1 line connection to the Internet so my new ADSL modem has a fatter pipe than my provider! (See table 1). It all makes me wonder what's in store for us in the future. PC technology has increased exponentially in the last 10 years with super fast processor speeds, hard disks of hundreds of gigabytes, and amazing video and audio. Internet connection speeds have failed to keep the same pace. Instead of hundreds of times better or faster--modem speeds are barely 10 times faster. Broadband connections offer some additional speed but still not comparable growth as broadband connections are still in their infancy. Rather than trying to make use of existing communication paths, maybe we need a massive infrastructure makeover of something new. How about national wireless access points so we can connect anywhere, anytime? To use the latest and fastest wireless technology you will simply need to buy another $9.95 WLAN card or download the latest super slick WLAN compression/encryption software. Perhaps it is time for a massive infra-restructuring. Consider the past massive infrastructure efforts. The telcos needed to put in their wiring infrastructure starting in the 1870s before telephones were useful to the

  15. CFRP strengthened openings in two-way concrete slabs

    DEFF Research Database (Denmark)

    Enochsson, O.; Lundqvist, J.; Täljsten, Björn

    2006-01-01

    Rehabilitation and strengthening of concrete structures with externally bonded fibre reinforced polymers (FRPs) has been a viable technique for at least a decade. An interesting and useful application is strengthening of slabs or walls where openings are introduced. In these situations, FRP sheets....... In this paper, laboratory tests on I I slabs with openings, loaded with a distributed load are presented together with analytical and numerical evaluations. Six slabs with openings have been strengthened with carbon fibre reinforced polymers (CFRPs) sheets. These slabs are compared with traditionally steel...

  16. STRUCTURAL TEST AND ANALYSIS OF RC SLAB AFTER FIRE LOADING

    Directory of Open Access Journals (Sweden)

    CHUL-HUN CHUNG

    2013-04-01

    Full Text Available In the present study the behavior of fire and the residual strength of fire-ignited RC slabs are investigated by experimental tests and numerical simulations. The fire tests of RC slabs were carried out in a furnace using the ISO 834 standard fire. The load capacity of the cooled RC slabs that were not loaded during the fire tests was evaluated by additional 3 point bending tests. The influence of the proportion of PP (polypropylene fibers in the RC slabs on the structural behavior of the RC slabs after the fire loading was investigated. The results of the fire tests showed that the maximum temperature of concrete with PP fiber was lower than that of concrete without PP fiber. As the concrete was heated, the ultimate compressive strength decreased and the ultimate strain increased. The load-deflection relations of RC slabs after fire loading were compared by using existing stress-strain-temperature models. The comparison between the numerical analysis and the experimental tests showed that some numerical analyses were reliable and therefore, can be applied to evaluate the ultimate load of RC slabs after fire loading. The ultimate load capacity after cooling down the RC slabs without PP fiber showed a considerable reduction from that of the RC slabs with PP fiber.

  17. Structural Test and Analysis of RC Slab After Fire Loading

    International Nuclear Information System (INIS)

    Chung, Chulhun; Im, Cho Rong; Park, Jaegyun

    2013-01-01

    In the present study the behavior of fire and the residual strength of fire-ignited RC slabs are investigated by experimental tests and numerical simulations. The fire tests of RC slabs were carried out in a furnace using the ISO 834 standard fire. The load capacity of the cooled RC slabs that were not loaded during the fire tests was evaluated by additional 3 point bending tests. The influence of the proportion of PP (polypropylene) fibers in the RC slabs on the structural behavior of the RC slabs after the fire loading was investigated. The results of the fire tests showed that the maximum temperature of concrete with PP fiber was lower than that of concrete without PP fiber. As the concrete was heated, the ultimate compressive strength decreased and the ultimate strain increased. The load-deflection relations of RC slabs after fire loading were compared by using existing stress-strain-temperature models. The comparison between the numerical analysis and the experimental tests showed that some numerical analyses were reliable and therefore, can be applied to evaluate the ultimate load of RC slabs after fire loading. The ultimate load capacity after cooling down the RC slabs without PP fiber showed a considerable reduction from that of the RC slabs with PP fiber

  18. A STUDY ON THE WHEELSET/SLAB TRACK VERTICAL INTERACTION

    OpenAIRE

    Traian MAZILU

    2012-01-01

    This paper deals with the interaction between a moving wheelset and a slab track due to the short-pitch corrugated rail. The wheelset is modeled using a free-free Timoshenko beam with attached rigid bodies as the axle boxes, wheels and brake discs. The slab track model consists of elastically supported double Euler-Bernoulli beams. In fact, both wheelset and slab track are symmetric structures and the issue of the wheelset/slab track interaction is reduced to the wheel/rail interaction. The n...

  19. Broadband Wireline Provider Service Summary; BBRI_wirelineSum12

    Data.gov (United States)

    University of Rhode Island Geospatial Extension Program — This dataset represents the availability of broadband Internet access in Rhode Island via all wireline technologies assessed by Broadband Rhode Island. Broadband...

  20. Reconstructing subducted oceanic lithosphere by “reverse-engineering” slab geometries : The northern Philippine Sea Plate

    NARCIS (Netherlands)

    Pownall, Jonathan M.; Lister, Gordon S.; Spakman, Wim|info:eu-repo/dai/nl/074103164

    Subducting slabs commonly acquire complex geometries from the migration of subduction trenches, slab-mantle interaction, slab tearing, and collision of slabs at depth. Although it is possible to construct three-dimensional models of subducted slabs using earthquake hypocenter locations and

  1. Slab thickness tuning approach for solid-state strong coupling between photonic crystal slab nanocavity and a quantum dot.

    Science.gov (United States)

    Chen, Gengyan; Liu, Jing-Feng; Jiang, Haoxiang; Zhuo, Xiao-Lu; Yu, Yi-Cong; Jin, Chongjun; Wang, Xue-Hua

    2013-04-23

    The quality factor and mode volume of a nanocavity play pivotal roles in realizing the strong coupling interaction between the nanocavity mode and a quantum dot. We present an extremely simple method to obtain the mode volume and investigate the effect of the slab thickness on the quality factor and mode volume of photonic crystal slab nanocavities. We reveal that the mode volume is approximatively proportional to the slab thickness. As compared with the previous structure finely optimized by introducing displacement of the air holes, via tuning the slab thickness, the quality factor can be enhanced by about 22%, and the ratio between the coupling coefficient and the nanocavity decay rate can be enhanced by about 13%. This can remarkably enhance the capability of the photonic crystal slab nanocavity for realizing the strong coupling interaction. The slab thickness tuning approach is feasible and significant for the experimental fabrication of the solid-state nanocavities.

  2. Behavior of Partially Restrained Reinforced Concrete Slabs.

    Science.gov (United States)

    1986-09-01

    1assiied 22a NAME OF RESPONSIBLE INDIVIDUAL 22b TELEPHONE (Include Area Code) 22c OFFICE SYMBOL DO FORM 1473, 84 MAR 83 APR edition may be used untI...Takehira, Derecho , and Iqbal [34] followed a similar approach to arrive at recommended design criteria for 1 the Naval Facilities Engineering Command...Compression in./in. Slab STI ST2 ST3 SSB - ___2 SB3_ CT _CB3 1 BC+ - C- CD+ - AB+ 0.0005 0.009 2 BC+ D+ - DE + AB+ AB+ 3 BC+ DE + CD+ D+ AB+ AB+ 0.011

  3. Sub-slab vs. Near-slab Soil Vapor Profiles at a Chlorinated Solvent Site (1)

    Science.gov (United States)

    A critical issue in assessing the vapor intrusion pathway is the distribution and migration of VOCs from the subsurface source to the near surface environment. Of particular importance is the influence of a slab. Therefore, EPA/ORD is funding a research program with the primary...

  4. Slab temperature controls on the Tonga double seismic zone and slab mantle dehydration.

    Science.gov (United States)

    Wei, S Shawn; Wiens, Douglas A; van Keken, Peter E; Cai, Chen

    2017-01-01

    Double seismic zones are two-layered distributions of intermediate-depth earthquakes that provide insight into the thermomechanical state of subducting slabs. We present new precise hypocenters of intermediate-depth earthquakes in the Tonga subduction zone obtained using data from local island-based, ocean-bottom, and global seismographs. The results show a downdip compressional upper plane and a downdip tensional lower plane with a separation of about 30 km. The double seismic zone in Tonga extends to a depth of about 300 km, deeper than in any other subduction system. This is due to the lower slab temperatures resulting from faster subduction, as indicated by a global trend toward deeper double seismic zones in colder slabs. In addition, a line of high seismicity in the upper plane is observed at a depth of 160 to 280 km, which shallows southward as the convergence rate decreases. Thermal modeling shows that the earthquakes in this "seismic belt" occur at various pressures but at a nearly constant temperature, highlighting the important role of temperature in triggering intermediate-depth earthquakes. This seismic belt may correspond to regions where the subducting mantle first reaches a temperature of ~500°C, implying that metamorphic dehydration of mantle minerals in the slab provides water to enhance faulting.

  5. Influence of weak layer heterogeneity and slab properties on slab tensile failure propensity and avalanche release area

    Science.gov (United States)

    Gaume, J.; Chambon, G.; Eckert, N.; Naaim, M.; Schweizer, J.

    2015-04-01

    Dry-snow slab avalanches are generally caused by a sequence of fracture processes, including failure initiation in a weak snow layer underlying a cohesive slab followed by crack propagation within the weak layer (WL) and tensile fracture through the slab. During past decades, theoretical and experimental work has gradually increased our knowledge of the fracture process in snow. However, our limited understanding of crack propagation and fracture arrest propensity prevents the evaluation of avalanche release sizes and thus impedes hazard assessment. To address this issue, slab tensile failure propensity is examined using a mechanically based statistical model of the slab-WL system based on the finite element method. This model accounts for WL heterogeneity, stress redistribution by slab elasticity and possible tensile failure of the slab. Two types of avalanche release are distinguished in the simulations: (1) full-slope release if the heterogeneity is not sufficient to stop crack propagation and trigger a tensile failure within the slab; (2) partial-slope release if fracture arrest and slab tensile failure occur due to the WL heterogeneity. The probability of these two release types is presented as a function of the characteristics of WL heterogeneity and the slab. One of the main outcomes is that, for realistic values of the parameters, the tensile failure propensity is mainly influenced by slab properties. Hard and thick snow slabs are more prone to wide-scale crack propagation and thus lead to larger avalanches (full-slope release). In this case, the avalanche size is mainly influenced by topographical and morphological features such as rocks, trees, slope curvature and the spatial variability of the snow depth as often claimed in the literature.

  6. 78 FR 32165 - Broadband Over Power Lines

    Science.gov (United States)

    2013-05-29

    ... applications for broadband and Smart Grid uses--while protecting incumbent radio services against harmful... Access BPL technology--which has potential applications for broadband and Smart Grid uses--while... that BPL systems increase the noise floor only within a relatively short distance (15-400 meters) from...

  7. 76 FR 71892 - Broadband Over Power Lines

    Science.gov (United States)

    2011-11-21

    ... that has potential applications for broadband and Smart Grid while protecting incumbent radio services... providing for Access BPL technology that has potential applications for broadband and Smart Grid while... line 230 meters from the coupler. ii. The proper distance extrapolation factor for assumed signal decay...

  8. 75 FR 10464 - Broadband Technology Opportunities Program

    Science.gov (United States)

    2010-03-08

    ... window for Public Computer Center (PCC) and Sustainable Broadband Adoption (SBA) projects. DATES: All...; Extension of Application Closing Deadline for Comprehensive Community Infrastructure (CCI) Projects. SUMMARY... Infrastructure (CCI) projects under the Broadband Technology Opportunities Program (BTOP) is extended until 5:00...

  9. Catalyzing Broadband Internet in Africa | IDRC - International ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Those without access, often women and the poor, risk being further excluded. Public policies can contribute to an affordable and inclusive broadband Internet infrastructure. To ensure the benefits of access to broadband are widely distributed, it is critical that policies take the needs of marginalized populations into ...

  10. Analyzing Broadband Divide in the Farming Sector

    DEFF Research Database (Denmark)

    Jensen, Michael; Gutierrez Lopez, Jose Manuel; Pedersen, Jens Myrup

    2013-01-01

    , upstream and downstream connection. The main constraint is that farms are naturally located in rural areas where the required access broadband data rates are not available. This paper studies the broadband divide in relation to the Danish agricultural sector. Results show how there is an important...

  11. 75 FR 25185 - Broadband Initiatives Program

    Science.gov (United States)

    2010-05-07

    ... applicable federal rules and regulations protecting against fraud, waste and abuse, contact [email protected] region create wealth so that they are self-sustaining, repopulating, and thriving economically... and focus on wealth and job creation through the use of broadband. Regional broadband development...

  12. Slab Profile Encoding (PEN) for Minimizing Slab Boundary Artifact in 3D Diffusion-Weighted Multislab Acquisition*

    Science.gov (United States)

    Van, Anh T; Aksoy, Murat; Holdsworth, Samantha J; Kopeinigg, Daniel; Vos, Sjoerd B; Bammer, Roland

    2014-01-01

    Purpose To propose a method for mitigating slab boundary artifacts in 3D multislab diffusion imaging with no or minimal increases in scan time. Methods The multislab acquisition was treated as parallel imaging acquisition where the slab profiles acted as the traditional receiver sensitivity profiles. All the slabs were then reconstructed simultaneously along the slab direction using Cartesian-based sensitivity encoding (SENSE) reconstruction. The slab profile estimation was performed using either a Bloch simulation or a calibration scan. Results Both phantom and in vivo results showed negligible slab boundary artifacts after reconstruction using the proposed method. The performance of the proposed method is comparable to the state-of-the-art slab combination method without the scan time penalty that depends on the number of acquired volumes. The obtained g-factor map of the SENSE reconstruction problem showed a maximum g-factor of 1.7 in the region of interest. Conclusion We proposed a novel method for mitigating slab boundary artifacts in 3D diffusion imaging by treating the multislab acquisition as a parallel imaging acquisition and reconstructing all slabs simultaneously using Cartesian SENSE. Unlike existing methods, the scan time increase, if any, does not scale with the number of image volumes acquired. PMID:24691843

  13. Slab profile encoding (PEN) for minimizing slab boundary artifact in three-dimensional diffusion-weighted multislab acquisition.

    Science.gov (United States)

    Van, Anh T; Aksoy, Murat; Holdsworth, Samantha J; Kopeinigg, Daniel; Vos, Sjoerd B; Bammer, Roland

    2015-02-01

    To propose a method for mitigating slab boundary artifacts in three-dimensional (3D) multislab diffusion imaging with no or minimal increases in scan time. The multislab acquisition was treated as parallel imaging acquisition where the slab profiles acted as the traditional receiver sensitivity profiles. All the slabs were then reconstructed simultaneously along the slab direction using Cartesian-based sensitivity encoding (SENSE) reconstruction. The slab profile estimation was performed using either a Bloch simulation or a calibration scan. Both phantom and in vivo results showed negligible slab boundary artifacts after reconstruction using the proposed method. The performance of the proposed method is comparable to the state-of-the-art slab combination method without the scan time penalty that depends on the number of acquired volumes. The obtained g-factor map of the SENSE reconstruction problem showed a maximum g-factor of 1.7 in the region of interest. We proposed a novel method for mitigating slab boundary artifacts in 3D diffusion imaging by treating the multislab acquisition as a parallel imaging acquisition and reconstructing all slabs simultaneously using Cartesian SENSE. Unlike existing methods, the scan time increase, if any, does not scale with the number of image volumes acquired. © 2014 Wiley Periodicals, Inc.

  14. Customer Churn Prediction for Broadband Internet Services

    Science.gov (United States)

    Huang, B. Q.; Kechadi, M.-T.; Buckley, B.

    Although churn prediction has been an area of research in the voice branch of telecommunications services, more focused studies on the huge growth area of Broadband Internet services are limited. Therefore, this paper presents a new set of features for broadband Internet customer churn prediction, based on Henley segments, the broadband usage, dial types, the spend of dial-up, line-information, bill and payment information, account information. Then the four prediction techniques (Logistic Regressions, Decision Trees, Multilayer Perceptron Neural Networks and Support Vector Machines) are applied in customer churn, based on the new features. Finally, the evaluation of new features and a comparative analysis of the predictors are made for broadband customer churn prediction. The experimental results show that the new features with these four modelling techniques are efficient for customer churn prediction in the broadband service field.

  15. Total internal reflection quasiphase matching-based broadband second harmonic generation in a plane-parallel uniaxial crystal of lithium niobate

    Science.gov (United States)

    Barma, Minakshi Deb; Deb, Sumita; Saha, Ardhendu

    2018-01-01

    The present work analytically investigates the generation of broadband second harmonic (SH) using total internal reflection (TIR) quasiphase matching technique in a plane-parallel uniaxial crystal having optic axis nonparallel with respect to the horizontal base. A computer-aided simulation has been performed using lithium niobate as the nonlinear material to determine the possibility of generating broadband SH intensity when broadband fundamental laser radiation is allowed to undergo TIR inside the crystal. The simulated results indicate a peak conversion efficiency of 5.22% with a spectral bandwidth (BW) of 116 nm, centered at 2.258 μm in a 10-mm-long slab. The effect of variation in operating temperature, crystal length, crystal thickness, angle of deviation of optic axis, and angle of incidence of fundamental beam at the air-prism interface on efficiency and BW of resulting SH output has been studied.

  16. Characteristics of a Broadband Dye Laser Using Pyrromethene and Rhodamine Dyes

    Science.gov (United States)

    Tedder, Sarah A.; Danehy, Paul M.; Wheeler, Jeffrey L.

    2011-01-01

    A broadband dye laser pumped by a frequency-doubled Nd:YAG laser with a full-width half-maximum (FWHM) from 592 to 610 nm was created for the use in a dual-pump broadband CARS system called WIDECARS. The desired broadband dye laser was generated with a mixture of Pyrromethene dyes as an oscillator gain medium and a spectral selective optic in the oscillator cavity. A mixture of Rhodamine dyes were used in the amplifier dye cell. To create this laser a study was performed to characterize the spectral behavior of broadband dye lasers created with Rhodamine dyes 590, 610, and 640, Pyrromethene dyes 597 and 650 as well as mixture of these dyes.

  17. Using the MDCT thick slab MinIP method for the follow-up of pulmonary emphysema.

    Science.gov (United States)

    Lan, Hai; Nishitani, Hiromu; Nishihara, Sadamitsu; Ueno, Junji; Takao, Shoichiro; Iwamoto, Seiji; Kawanaka, Takashi; Mahmut, Mawlan; Qingge, Si

    2011-08-01

    The purpose of this study was to evaluate the usefulness of thick slab minimum intensity projection (MinIP) as a follow-up method in patients with pulmonary emphysema. This method was used to determine the presence or absence of changes over time in the lung field based on multi-detector-row CT (MDCT) data. Among patients diagnosed with pulmonary emphysema who underwent 16-MDCT (slice thickness, 1 mm) twice at an interval of 6 months or more, 12 patients without changes in the lung field and 14 with clear changes in the lung field were selected as subjects. An image interpretation experiment was performed by five image interpreters. Pulmonary emphysema was followed up using two types of thick slab MinIP (thick slab MinIP 1 and 2) and multi-planar reformation (MPR), and the results of image interpretation were evaluated by receiver operating characteristic (ROC) analysis. In addition, the time required for image interpretation was compared among the three follow-up methods. The area under the ROC curve (Az) was 0.794 for thick slab MinIP 1, 0.778 for the thick slab MinIP 2, and 0.759 for MPR, showing no significant differences among the three methods. Individual differences in each item were significantly more marked for MPR than for thick slab MinIP. The time required for image interpretation was around 18 seconds for thick slab MinIP 1, 11 seconds for thick slab MinIP 2, and approximately 127 seconds for MPR, showing significant differences among the three methods. There were no significant differences in the results of image interpretation regarding the presence or absence of changes in the lung fields between thick slab MinIP and MPR. However, thick slab MinIP showed a shorter image interpretation time and smaller individual differences in the results among image interpreters than MPR, suggesting the usefulness of this method for determining the presence or absence of changes with time in the lung fields of patients with pulmonary emphysema.

  18. Slab dehydration in Cascadia and its relationship to volcanism, seismicity, and non-volcanic tremor

    Science.gov (United States)

    Delph, J. R.; Levander, A.; Niu, F.

    2017-12-01

    The characteristics of subduction beneath the Pacific Northwest (Cascadia) are variable along strike, leading to the segmentation of Cascadia into 3 general zones: Klamath, Siletzia, and Wrangelia. These zones show marked differences in tremor density, earthquake density, seismicity rates, and the locus and amount of volcanism in the subduction-related volcanic arc. To better understand what controls these variations, we have constructed a 3D shear-wave velocity model of the upper 80 km along the Cascadia margin from the joint inversion of CCP-derived receiver functions and ambient noise surface wave data using 900 temporary and permanent broadband seismic stations. With this model, we can investigate variations in the seismic structure of the downgoing oceanic lithosphere and overlying mantle wedge, the character of the crust-mantle transition beneath the volcanic arc, and local to regional variations in crustal structure. From these results, we infer the presence and distribution of fluids released from the subducting slab and how they affect the seismic structure of the overriding lithosphere. In the Klamath and Wrangelia zones, high seismicity rates in the subducting plate and high tremor density correlate with low shear velocities in the overriding plate's forearc and relatively little arc volcanism. While the cause of tremor is debated, intermediate depth earthquakes are generally thought to be due to metamorphic dehydration reactions resulting from the dewatering of the downgoing slab. Thus, the seismic characteristics of these zones combined with rather sparse arc volcanism may indicate that the slab has largely dewatered by the time it reaches sub-arc depths. Some of the water released during earthquakes (and possibly tremor) may percolate into the overriding plate, leading to slow seismic velocities in the forearc. In contrast, Siletzia shows relatively low seismicity rates and tremor density, with relatively higher shear velocities in the forearc

  19. TECHNOLOGY FOR INSTALLATION OF REINFORCED CONCRETE FLOOR SLABS LIGHTENED BY CORE DRIVERS WITH PRELIMINARY REINFORCEMENT STRESS

    OpenAIRE

    S. N. Leonovich; I. I. Peredkov

    2015-01-01

    The paper presents technology for installation of floor slabs lightened by plastic core drivers which are preliminary stressed under construction conditions.  Efficiency of such constructive solution is justified by the action of preliminary concrete compression in the tensile zone while reducing structure dead weight due to void arrangement.  The paper provides classification of systems for preliminary stress and contains recommendations on selection of the system depending on peculiariar fe...

  20. Accelerated slab replacement using temporary precast panels and self-consolidating concrete : [summary].

    Science.gov (United States)

    2016-06-01

    Researchers at Florida State University demonstrated the feasibility of using precast reinforced concrete panels to temporarily fill slab removal pits. The precast slabs can be driven on so traffic lanes can be open during the day, and new slab casti...

  1. Strategy for the deployment of a dense broadband temporary array in the Alps: lessons learnt from the CIFALPS experiment

    Science.gov (United States)

    Coralie, Aubert; Anne, Paul; Stefano, Solarino; Sandrine, Roussel; Simone, Salimbeni; Pierre, Zangelmi; Glenn, Cougoulat; Yinshuang, Ai; Weiwei, Xu; Yumei, He; Liang, Zhao

    2013-04-01

    The CIFALPS (China-Italy-France Alps seismic survey) experiment is a common project of IGGCAS (China), ISTerre (France) and INGV (Italy). It aims at getting new high-resolution passive seismic data on the crustal and upper mantle structure of the southwestern Alps. In this framework, we have installed a temporary broadband seismic array across the southwestern Alps from the Rhône valley (France) to the Po plain (Italy). The main sub-array of CIFALPS is a 350-km long roughly linear profile of 46 stations trending WSW-ENE from Bollène (France) to north of Alessandria (Italy). The average station spacing is 10 km in the outer parts of the belt, and it reduces to 5 km in the internal Alps. Nine additional temporary stations located ~40 km to the north and south of the main profile complement the permanent broadband networks to improve the 3-D constraints on the deep structures. Stations are equipped with Nanometrics Taurus data acquisition systems, and Trillium 120P/A, CMG3-ESP or CMG40T broadband sensors. The array was installed in the summer of 2012 and will be operated at least to April 2013. Because our schedule was tight, we had to achieve site selections in only 3-4 months in spite of strong constraints on site location related to short interstation spacing. Most sites are located in basements of buildings for security reasons and mains power supply. As most sensors are true broadband (90s or 120s), we put much effort on vault design to insure good thermal insulation and low noise at long periods. The vaults also had to be easily and rapidly built and they should be easily and totally removed at the end of the experiment. We used the PQLX software for quality control of our sites and vault design. The performances of our vaults are good for the vertical component with noise levels at 100s period in the range -185 dB (low noise model) to -165 dB. They are less good for horizontal components (noise level close to high noise model at periods > 20s) due to

  2. Precast alternative for flat slab bridges : final report.

    Science.gov (United States)

    2013-10-26

    The cast-in-place (CIP) concrete slab bridge and the hollow core flat slab bridge are two very common bridge types utilized by the : South Carolina Department of Transportation (SCDOT). The CIP bridge is durable but has a long construction time while...

  3. On Early Age Crack Formation in FRC Slabs

    DEFF Research Database (Denmark)

    Olesen, John Forbes; Stang, Henrik

    1997-01-01

    The problem of early age crack formation in FRC slabs due to restrained temperature and shrinkage deformations, is given an analytical treatment. A model taking into account the ageing properties of the tensile softening curve and the continued development in the temperature and shrinkage...... deformations after crack initiation, is presented. Based on this model a design strategy for FRC slabs is outlined....

  4. Fire resistance of extruded hollow-core slabs

    DEFF Research Database (Denmark)

    Hertz, Kristian Dahl; Giuliani, Luisa; Sørensen, Lars Schiøtt

    2016-01-01

    Prefabricated extruded hollow-core slabs are preferred building components for floor structures in several countries. It is therefore important to be able to document the fire resistance of these slabs proving fulfilment of standard fire resistance requirements of 60- and 120 minutes found in most...

  5. Fire resistance of extruded hollow-core slabs

    DEFF Research Database (Denmark)

    Hertz, Kristian Dahl; Sørensen, Lars Schiøtt; Giuliani, Luisa

    2017-01-01

    Purpose – Prefabricated extruded hollow-core slabs are preferred building components for floor structures in several countries. It is therefore important to be able to document the fire resistance of these slabs proving fulfilment of standard fire resistance requirements of 60 and 120 min found...

  6. Shear capacity of slabs under a combination of loads

    NARCIS (Netherlands)

    Lantsoght, E.O.L.; Van der Veen, C.; Walraven, J.C.

    2013-01-01

    Existing solid slab bridges under a combination of wheel loads and distributed traffic loads sometimes do not fulfil the code requirements for shear. However, reinforced concrete slabs loaded close to the support are subjected to shear stresses which might result in a failure mode of combined

  7. Safety of Premature Loading on Reinforced Concrete Slabs | Shema ...

    African Journals Online (AJOL)

    ... two-thirds of its characteristic strength. The reliability indices of a prematurely loaded reinforced concrete slab in flexure are directly proportional to the characteristic strength of concrete. Therefore in practice, due consideration must be given to early-age strength development in reinforced concrete slabs before loading.

  8. Manipulation of enhanced absorption with tilted hexagonal boron nitride slabs

    Science.gov (United States)

    Wu, Xiaohu; Fu, Ceji

    2018-04-01

    The wavevector of electromagnetic wave propagation in a hexagonal boron nitride (hBN) slab can be controlled by tilting its optical axis. This property can be used to manipulate the absorption in a hBN slab. By carefully analyzing the dependence of the absorptivity of a thin hBN slab on the tilted angle of its optical axis, we propose a structure that can realize great absorptivity enhancement in a band by stacking hBN slabs of different tilted angles. Our numerical results show that the absorptivity of a structure made of 91 stacked hBN slabs can be achieved higher than 0.94 in the wavenumber range from 1367 to 1580 cm-1 when the tilted angles of the slabs are properly arranged. The strong absorption is attributed to the combination of impedance matching at the slab interfaces and enlarged wavevectors in the slabs. This work reveals a novel way to realize strong absorption with anisotropic materials for applications in areas such as thermal radiative energy harvesting and conversion.

  9. Shear and Anchorage Behaviour of Fire Exposed Hollow Core Slabs

    NARCIS (Netherlands)

    Fellinger, J.H.H.

    2004-01-01

    Hollow core (HC) slabs are made of precast concrete with pretensioned strands. These slabs are popular as floor structures in offices and housing. At ambient conditions, the load bearing capacity can be dominated by four different failure modes, i.e. flexure, anchorage, shear compression and shear

  10. Shear and anchorage behaviour of fire exposed hollow core slabs

    NARCIS (Netherlands)

    Fellinger, J.H.H.; Stark, J.; Walraven, J.C.

    2005-01-01

    The fire resistance of hollow core slabs is currently assessed considering flexural failure only. However, fire tests showed that shear or anchorage failure can also govern the load bearing behaviour. As the shear and anchorage capacity of these slabs rely on the tensile strength of the concrete,

  11. Empirical Strengths of Concrete Roof Slabs After 34 Years Service ...

    African Journals Online (AJOL)

    This paper examines the strengths of four reinforced concrete roof slabs which have been in service for over 34years. The non-destructive test hammer was used to obtain data for the empirical determination of the practical strengths of the existing structures. A total of 110 tests were performed on each slab at 11 points ...

  12. Surface Waves Propagating on Grounded Anisotropic Dielectric Slab

    Directory of Open Access Journals (Sweden)

    Zhuozhu Chen

    2018-01-01

    Full Text Available This paper investigates the characteristics of surface waves propagating on a grounded anisotropic dielectric slab. Distinct from the existing analyses that generally assume that the fields of surface wave uniformly distribute along the transverse direction of the infinitely large grounded slab, our method takes into account the field variations along the transverse direction of a finite-width slab. By solving Maxwell’s equations in closed-form, it is revealed that no pure transverse magnetic (TM or transverse electric (TE mode exists if the fields are non-uniformly distributed along the transverse direction of the grounded slab. Instead, two hybrid modes, namely quasi-TM and quasi-TE modes, are supported. In addition, the propagation characteristics of two hybrid modes supported by the grounded anisotropic slab are analyzed in terms of the slab thickness, slab width, as well as the relative permittivity tensor of the anisotropic slab. Furthermore, different methods are employed to compare the analyses, as well as to validate our derivations. The proposed method is very suitable for practical engineering applications.

  13. Tuchola County Broadband Network (TCBN)

    DEFF Research Database (Denmark)

    Zabludowski, Antoni; Dubalski, B.; Zabludowski, Lukasz

    2012-01-01

    In the paper the designing project (plan) of Tuchola City broadband IP optical network has been presented. The extended version of network plan constitute technical part of network Feasibility Study, that it is expected to be implemented in Tuchola and be financed from European Regional Development...... Funds. The network plan presented in the paper contains both topological structure of fiber optic network as well as the active equipment for the network. In the project described in the paper it has been suggested to use Modular Cable System - MCS for passive infrastructure and Metro Ethernet...... technology for active equipment. The presented solution provides low cost of construction (CAPEX), ease of implementation of the network and low operating cost (OPEX). Moreover the parameters of installed Metro Ethernet switches in the network guarantee the scalability of the network for at least 10 years....

  14. Numerical Study of FRP Reinforced Concrete Slabs at Elevated Temperature

    Directory of Open Access Journals (Sweden)

    Masoud Adelzadeh

    2014-02-01

    Full Text Available One-way glass fibre reinforced polymer (GFRP reinforced concrete slabs at elevated temperatures are investigated through numerical modeling. Serviceability and strength requirements of ACI-440.1R are considered for the design of the slabs. Diagrams to determine fire endurance of slabs by employing “strength domain” failure criterion are presented. Comparisons between the existing “temperature domain” method with the more representative “strength domain” method show that the “temperature domain” method is conservative. Additionally, a method to increase the fire endurance of slabs by placing FRP reinforcement in two layers is investigated numerically. The amount of fire endurance gained by placing FRP in two layers increases as the thickness of slab increases.

  15. Shear strength of end slabs of prestressed concrete reactor vessels

    International Nuclear Information System (INIS)

    Cheung, K.C.; Gotschall, H.L.; Liu, T.C.

    1975-01-01

    Prestressed concrete reactor vessels (PCRV's) have been adopted for primary containments in most large high-temperature gas-cooled reactor installations. The most common configuration for PCRVs is a right-vertical cylinder with thick end slabs. In order to assess the integrity of a PCRV it is necessary to predict the ultimate strength of the end slabs. The complexity of the basic mechanism of shear failure in the PCRV end slabs has thus far prohibited the development of a completely analytical solution. However, many experimental investigations of PCRV end slabs have been conducted over the past decade. This information makes it possible to establish empirical formulae for the ultimate strength of PCRV end slabs. The basis and development of an empirical shear-flexure interaction expression is presented. (Auth.)

  16. The gravitational field of an infinite flat slab

    International Nuclear Information System (INIS)

    Fulling, S A; Bouas, J D; Carter, H B

    2015-01-01

    We study Einstein's equations with a localized plane-symmetric source, with close attention to gauge freedom/fixing and to listing all physically distinct solutions. In the vacuum regions there are only two qualitatively different solutions, one curved and one flat; in addition, on each of the two sides there is a free parameter describing how the slab is embedded into the vacuum region. Surprisingly, for a generic slab source the solution must be curved on one side and flat on the other. We treat infinitely thin slabs in full detail and indicate how thick slabs can increase the variety of external geometry pairs. Positive energy density seems to force external geometries with curvature singularities at some distance from the slab; we speculate that such singularities occur in regions where the solution cannot be physically relevant anyway. (invited comment)

  17. Evaluation of dynamic behavior of waffle slab to gym center

    Directory of Open Access Journals (Sweden)

    Yuri Cláudio Vieira da Costa

    Full Text Available In Brazil, the use of reinforced concrete waffle slab in multi-story buildings is widespread nowadays. These buildings are projected for different purposes such as fitness centers, supermarkets, parking garages, offices and residential units. Simple activities as walking, skipping and jumping can generate vibrations in these slabs. Vibrations can cause inconvenience in persons, questions about structure´s safety, and collapse risk that it is determined by its intensity of vibrations. The objective of this paper is evaluating the behavior of reinforced concrete waffle slabs due to the human rhythmic activities. Slabs are modeled by finite elements method using the SAP2000 program. The results are verified according to Brazilian and international codes. The waffle slabs are submitted to high-levels of acceleration and velocity generating discomfort in users.

  18. Characterizing wet slab and glide slab avalanche occurrence along the Going-to-the-Sun Road, Glacier National Park, Montana, USA

    Science.gov (United States)

    Peitzsch, Erich H.; Hendrikx, Jordy; Fagre, Daniel B.; Reardon, Blase

    2010-01-01

    Wet slab and glide slab snow avalanches are dangerous and yet can be particularly difficult to predict. Both wet slab and glide slab avalanches are thought to depend upon free water moving through the snowpack but are driven by different processes. In Glacier National Park, Montana, both types of avalanches can occur in the same year and affect the Going-to-the-Sun Road (GTSR). Both wet slab and glide slab avalanches along the GTSR from 2003-2010 are investigated. Meteorological data from two high-elevation weather stations and one SNOTEL site are used in conjunction with an avalanche database and snowpit profiles. These data were used to characterize years when only glide slab avalanches occurred and those years when both glide slab and wet slab avalanches occurred. Results of 168 glide slab and 57 wet slab avalanches along the GTSR suggest both types of avalanche occurrence depend on sustained warming periods with intense solar radiation (or rain on snow) to produce free water in the snowpack. Differences in temperature and net radiation metrics between wet slab and glide slab avalanches emerge as one moves from one day to seven days prior to avalanche occurrence. On average, a more rapid warming precedes wet slab avalanche occurrence. Glide slab and wet slab avalanches require a similar amount of net radiation. Wet slab avalanches do not occur every year, while glide slab avalanches occur annually. These results aim to enhance understanding of the required meteorological conditions for wet slab and glide slab avalanches and aid in improved wet snow avalanche forecasting.

  19. Possible deviations from Griffith’s criterion in shallow slabs, and consequences on slab avalanche release

    Directory of Open Access Journals (Sweden)

    F. Louchet

    2002-01-01

    Full Text Available Possible reasons for deviations from Griffith’s criterion in slab avalanche triggerings are examined. In the case of a major basal crack, we show (i that the usual form of Griffith’s criterion is valid if elastic energy is stored in a shallow and hard slab only, and (ii that rapid healing of broken ice bonds may lead to shear toughnesses larger than expected from tensile toughness experiments. In the case of avalanches resulting from failure of multi-cracked weak layers, where a simple Griffith’s criterion cannot be applied, frequency/size plots obtained from discrete elements and cellular automata simulations are shown to obey scale invariant power law distributions. These findings are confirmed by both frequency/acoustic emission duration and frequency/size plots obtained from field data, suggesting that avalanche triggerings may be described using the formalism of critical phenomena.

  20. Sum frequency generation under conversion of Q-switched cryogenic slab RF discharge CO laser radiation in ZnGeP2

    Science.gov (United States)

    Ionin, A. A.; Kinyaevskiy, I. O.; Klimachev, Yu M.; Kochetkov, Yu V.; Kozlov, A. Yu; Seleznev, L. V.; Sinitsyn, D. V.; Zemtsov, D. S.; Andreev, Yu M.

    2018-02-01

    For the first time broadband sum frequency generation in ZnGeP2 crystal has been accomplished with a compact cryogenic slab RF discharge CO laser. The spectrum of the CO laser operating in a repetitively pulsed multiline Q-switching mode consisted of ~90 emission lines in the wavelength range of 4.95–6.60 µm. Internal sum frequency generation efficiency was reached up to 8.2%. The resulted spectrum contained ~200 spectral lines in the wavelength range of 2.5–3.2 µm.

  1. Policy factors affecting broadband development in Poland

    DEFF Research Database (Denmark)

    Henten, Anders; Windekilde, Iwona Maria

    2014-01-01

    ’s telecommunications market with the European market. The market reflects all the global trends, a gradually growing significance of mobile telecommunications services, broadband Internet access, construction of offers directed towards clients’ needs, and a strong trend towards market consolidation, which...... and discuss broadband access development in Poland and the policy factors influencing this development as well as to examine national strategies used to stimulate service and infrastructure competition in Poland. There are, indeed, many other factors affecting broadband development such as the income level...

  2. Broadband properties of active galactic nuclei

    Science.gov (United States)

    Edelson, Richard Allen

    The broadband radio-infrared-optical-ultraviolet properties of active galactic nuclei are used to investigate the nature of the central engine and the surrounding environment. Optically selected quasars and Seyfert 1 galaxies tend to have relatively flat infrared spectra and low reddenings, while most Seyfert 2 galaxies and other dusty objects have steep infrared spectra and larger reddenings. The infrared spectra of most luminous radio-quiet active galaxies turn over near approx. 80 micron. It appears that the infrared spectra of most quasars and luminous Seyfert 1 galaxies are dominated by unreprocessed radiation from a synchrotron self-absorbed source of order a light day across, about the size of the hypothesized accretion disk. Seyfert 2 galaxies and other reddened objects have infrared spectra which appear to be dominated by thermal emission from warm dust, probably in the disk of the underlying galaxy. A broad emission feature, centered near 5 micron, is present in many luminous quasars and Seyfert 1 galaxies. Highly polarized objects (blazars) can be strongly variable at far infrared wavelengths over time scales of months. Seyfert galaxies tend to have steep radio spectra.

  3. Broadband Cooperative Spectrum Sensing Based on Distributed Modulated Wideband Converter

    Directory of Open Access Journals (Sweden)

    Ziyong Xu

    2016-09-01

    Full Text Available The modulated wideband converter (MWC is a kind of sub-Nyquist sampling system which is developed from compressed sensing theory. It accomplishes highly accurate broadband sparse signal recovery by multichannel sub-Nyquist sampling sequences. However, when the number of sparse sub-bands becomes large, the amount of sampling channels increases proportionally. Besides, it is very hard to adjust the number of sampling channels when the sparsity changes, because its undersampling board is designed by a given sparsity. Such hardware cost and inconvenience are unacceptable in practical applications. This paper proposes a distributed modulated wideband converter (DMWC scheme innovatively, which regards one sensor node as one sampling channel and combines MWC technology with a broadband cooperative spectrum sensing network perfectly. Being different from the MWC scheme, DMWC takes phase shift and transmission loss into account in the input terminal, which are unavoidable in practical application. Our scheme is not only able to recover the support of broadband sparse signals quickly and accurately, but also reduces the hardware cost of the single node drastically. Theoretical analysis and numerical simulations show that phase shift has no influence on the recovery of frequency support, but transmission loss degrades the recovery performance to a different extent. Nevertheless, we can increase the amount of cooperative nodes and select satisfactory nodes by a different transmission distance to improve the recovery performance. Furthermore, we can adjust the amount of cooperative nodes flexibly when the sparsity changes. It indicates DMWC is extremely effective in the broadband cooperative spectrum sensing network.

  4. Impact Resistance Behaviour of Banana Fiber Reinforced Slabs

    Science.gov (United States)

    Che Muda, Zakaria; Syamsir, Agusril; Nasharuddin Mustapha, Kamal; Rifdy Samsudin, Muhamad; Thiruchelvam, Sivadass; Usman, Fathoni; Beddu, Salmia; Liyana Mohd Kamal, Nur; Ashraful Alam, Md; Birima, Ahmed H.; Zaroog, O. S.

    2016-03-01

    This paper investigate the performance of banana fibre reinforced slabs 300mm × 300mm size with varied thickness subjected to low impact projectile test. A self-fabricated drop-weight impact test rig with a steel ball weight of 1.25 kg drop at 1 m height has been used in this research work. The main variables for the study is to find the relationship of the impact resistance against the BF contents and slab thickness. A linear relationship has been established between first and ultimate crack resistance against BF contents and slab thickness by the experiment. The linear relationship has also been established between the service (first) crack and ultimate crack resistance against the BF contents for a constant spacing for various banana fibre reinforced slab thickness. The increment in BF content has more effect on the first crack resistance than the ultimate crack resistance. The linear relationship has also been established between the service (first) crack and ultimate crack resistance against the various slab thickness. Overall 1.5% BF content with slab thickness of 40 mm exhibit better first and ultimate crack resistance up to 16 times and up to 17 times respectively against control slab (without BF)

  5. 75 FR 14131 - Broadband Technology Opportunities Program

    Science.gov (United States)

    2010-03-24

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF COMMERCE... Program AGENCY: National Telecommunications and Information Administration, U.S. Department of Commerce... for the electronic submission of CCI projects under the Broadband Technology Opportunities Program...

  6. Analysis of United States' Broadband Policy

    National Research Council Canada - National Science Library

    Uzarski, Joel S

    2007-01-01

    .... With every month that passes, the United States fails to close the gap in the digital divide both inside its borders as well as among the other countries that lead the world in broadband penetration...

  7. Broadband Advanced Spectral System, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — NovaSol proposes to develop an advanced hyperspectral imaging system for earth science missions named BRASS (Broadband Advanced Spectral System). BRASS combines...

  8. Broadband luminescent materials in waveguide geometry

    NARCIS (Netherlands)

    Pollnau, Markus

    2003-01-01

    Our recent research toward the development of novel spectrally broadband, spatially coherent light sources based on transition-metal-ion-doped crystalline channel waveguides for applications in interferometry, specifically optical low coherence reflectometry and optical coherence tomography, is

  9. Nanophotonic Design for Broadband Light Management

    Energy Technology Data Exchange (ETDEWEB)

    Kosten, Emily; Callahan, Dennis; Horowitz, Kelsey; Pala, Ragip; Atwater, Harry

    2014-10-13

    We describe nanophotonic design approaches for broadband light management including i) crossed-trapezoidal Si structures ii) Si photonic crystal superlattices, and iii) tapered and inhomogeneous diameter III-V/Si nanowire arrays.

  10. Is European Broadband Ready for Smart Grid?

    DEFF Research Database (Denmark)

    Balachandran, Kartheepan; Pedersen, Jens Myrup

    2014-01-01

    In this short paper we compare the communication requirements for three Smart Grid scenarios with the availability of broadband and mobile communication networks in Europe. We show that only in the most demanding case - where data is collected and transmitted every second - a standard GSM....../GPRS connection is not enough. Whereas in the less demanding scenarios it is almost all of the European households that can be covered by a standard broadband technology for use with Smart Grid....

  11. Interaction of an ion bunch with a plasma slab

    Energy Technology Data Exchange (ETDEWEB)

    Krasovitskiy, V. B., E-mail: krasovit@mail.ru [Russian Academy of Sciences, Keldysh Institute of Applied Mathematics (Russian Federation); Turikov, V. A. [Peoples’ Friendship University of Russia (Russian Federation)

    2016-11-15

    Charge neutralization of a short ion bunch passing through a plasma slab is studied by means of numerical simulation. It is shown that a fraction of plasma electrons are trapped by the bunch under the action of the collective charge separation field. The accelerated electrons generated in this process excite beam−plasma instability, thereby violating the trapping conditions. The process of electron trapping is also strongly affected by the high-frequency electric field caused by plasma oscillations at the slab boundaries. It is examined how the degree of charge neutralization depends on the parameters of the bunch and plasma slab.

  12. Rayleigh-Taylor instability in accelerated elastic-solid slabs

    Science.gov (United States)

    Piriz, S. A.; Piriz, A. R.; Tahir, N. A.

    2017-12-01

    We develop the linear theory for the asymptotic growth of the incompressible Rayleigh-Taylor instability of an accelerated solid slab of density ρ2, shear modulus G , and thickness h , placed over a semi-infinite ideal fluid of density ρ110.1007/s000330050121] to arbitrary values of AT and unveil the singular feature of an instability threshold below which the slab is stable for any perturbation wavelength. As a consequence, an accelerated elastic-solid slab is stable if ρ2g h /G ≤2 (1 -AT) /AT .

  13. A broadband accelerator control network

    International Nuclear Information System (INIS)

    Skelly, J.; Clifford, T.; Frankel, R.

    1983-01-01

    A broadband data communications network has been implemented at BNL for control of the Alternating Gradient Synchrotron (AGS) proton accelerator, using commercial CATV hardware, dual coaxial cables as the communications medium, and spanning 2.0 km. A 4 MHz bandwidth Digital Control Channel using CSMA-CA protocol is provided for digital data transmission, with 8 access nodes available over the length of the RELWAY. Each node consists of an rf modem and a microprocessor-based store-and-forward message handler which interfaces the RELWAY to a branch line implemented in GPIB. A gateway to the RELWAY control channel for the (preexisting) AGS Computerized Accelerator Operating System has been constructed using an LSI-11/23 microprocessor as a device in a GPIB branch line. A multilayer communications protocol has been defined for the Digital Control Channel, based on the ISO Open Systems Interconnect layered model, and a RELWAY Device Language defined as the required universal language for device control on this channel

  14. Interpreting Flux from Broadband Photometry

    Science.gov (United States)

    Brown, Peter J.; Breeveld, Alice; Roming, Peter W. A.; Siegel, Michael

    2016-10-01

    We discuss the transformation of observed photometry into flux for the creation of spectral energy distributions (SED) and the computation of bolometric luminosities. We do this in the context of supernova studies, particularly as observed with the Swift spacecraft, but the concepts and techniques should be applicable to many other types of sources and wavelength regimes. Traditional methods of converting observed magnitudes to flux densities are not very accurate when applied to UV photometry. Common methods for extinction and the integration of pseudo-bolometric fluxes can also lead to inaccurate results. The sources of inaccuracy, though, also apply to other wavelengths. Because of the complicated nature of translating broadband photometry into monochromatic flux densities, comparison between observed photometry and a spectroscopic model is best done by forward modeling the spectrum into the count rates or magnitudes of the observations. We recommend that integrated flux measurements be made using a spectrum or SED which is consistent with the multi-band photometry rather than converting individual photometric measurements to flux densities, linearly interpolating between the points, and integrating. We also highlight some specific areas where the UV flux can be mischaracterized.

  15. Broadband electromagnetic environments simulator (EMES)

    International Nuclear Information System (INIS)

    Pollard, N.

    1977-01-01

    A new test facility has been developed by Sandia Laboratories for determining the effects of electromagnetic environments on systems and components. The facility is capable of producing uniform, vertically polarized, continuous wave (CW) and pulsed fields over the frequency range of dc to 10 GHz. This broadband capability addresses the electromagnetic radiation (EMR) threat and is ideally suited to computer controlled sweeping and data acquisition. EMES is also capable of producing uniform transient fields having the wave shape and magnitude characteristic of a nuclear electromagnetic pulse (EMP) and near lightning. The design consists of a truncated, triplate, rectangular coaxial transmission line. The spacing between the flat center conductor and the ground planes is 4 meters. The line is terminated in its characteristic impedance of 50 ohms. At frequencies below the first resonance of the facility it behaves as a typical coaxial system. Above resonance, a wall of electromagnetic absorbing material provides a nonreflecting termination. Thus, EMES essentially combines the elements of a transmission line and an anechoic chamber. It will not radiate electromagnetic energy into the surrounding area because it is a shielded transmission line

  16. May eclogite dehydration cause slab fracturation ?

    Science.gov (United States)

    Loury, Chloé; Lanari, Pierre; Rolland, Yann; Guillot, Stéphane; Ganino, Clément

    2015-04-01

    Petrological and geophysical evidences strongly indicate that fluids releases play a fundamental role in subduction zones as in subduction-related seismicity and arc magmatism. It is thus important to assess quantitatively their origin and to try to quantify the amount of such fluids. In HP metamorphism, it is well known that pressure-dependent dehydration reactions occur during the prograde path. Many geophysical models show that the variations in slab physical properties along depth could be linked to these fluid occurrences. However it remains tricky to test such models on natural sample, as it is difficult to assess or model the water content evolution in HP metamorphic rocks. This difficulty is bound to the fact that these rocks are generally heterogeneous, with zoned minerals and preservation of different paragenesis reflecting changing P-T conditions. To decipher the P-T-X(H2O) path of such heterogeneous rocks the concept of local effective bulk (LEB) composition is essential. Here we show how standardized X-ray maps can be used to constrain the scale of the equilibration volume of a garnet porphyroblast and to measure its composition. The composition of this equilibrium volume may be seen as the proportion of the rock likely to react at a given time to reach a thermodynamic equilibrium with the growing garnet. The studied sample is an eclogite coming from the carboniferous South-Tianshan suture (Central Asia) (Loury et al. in press). Compositional maps of a garnet and its surrounding matrix were obtained from standardized X-ray maps processed with the program XMapTools (Lanari et al, 2014). The initial equilibration volume was modeled using LEB compositions combined together with Gibbs free energy minimization. P-T sections were calculated for the next stages of garnet growth taking into account the fractionation of the composition at each stage of garnet growth. The modeled P-T-X(H2O) path indicates that the rock progressively dehydrates during the

  17. Optimising the Slab Yard Planning and Crane Scheduling Problem using a two-stage heuristic

    DEFF Research Database (Denmark)

    Hansen, Anders Dohn; Clausen, Jens

    2010-01-01

    In this paper, we present the Slab Yard Planning and Crane Scheduling Problem. The problem has its origin in steel production facilities with a large throughput. A slab yard is used as a buffer for slabs that are needed in the upcoming production. Slabs are transported by cranes and the problem...

  18. 29 CFR 1926.705 - Requirements for lift-slab construction operations.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Requirements for lift-slab construction operations. 1926... Masonry Construction § 1926.705 Requirements for lift-slab construction operations. (a) Lift-slab...-slab construction. Such plans and designs shall be implemented by the employer and shall include...

  19. Calculation of shear strength of prestressed hollow core slabs by use of plastic theory

    DEFF Research Database (Denmark)

    Hoang, Linh Cao; Jørgensen, H.G.; Nielsen, Mogens Peter

    2014-01-01

    Th is paper deals with calculations of the shear capacity of precast, prestressed hollow core slabs. Such slabs are often used as floor systems in building structures. A common way to produce hollow core slabs is to use the extrusion technique where long strips of slabs are extruded and thereafter...

  20. Integral bridge abutment-to-approach slab connection.

    Science.gov (United States)

    2008-06-01

    The Iowa Department of Transportation has long recognized that approach slab pavements of integral abutment bridges are prone to settlement and cracking, which manifests as the "bump at the end of the bridge". A commonly recommended solution is to in...

  1. The rideability of a deflected bridge approach slab.

    Science.gov (United States)

    2009-11-01

    This report presents the findings associated with the development of a new pavement roughness index called the Posted Speed Localized Roughness Index (LRIPS) that can be used to rate the ride quality on bridge approach slabs. Currently established pa...

  2. Field demonstration of new bridge approach slab designs and performance.

    Science.gov (United States)

    2014-06-01

    The Louisiana Department of Transportation and Development (DOTD) has initiated a major effort to minimize the bridge end bump problem associated : with differential settlement. As a result, a new design for the approach slab was proposed, which requ...

  3. Evaluation of precast concrete slabs using a heavy vehicle simulator

    CSIR Research Space (South Africa)

    Kohler, E

    2008-10-01

    Full Text Available -controlled conditions and that fully cured precast slabs can potentially be open to traffic almost immediately upon installation, making them attractive for use on heavily travelled highways. This paper describes an accelerated pavement testing experiment conducted...

  4. Effects of Posttensioning Slippage on 2-Way Spanning Concrete Slabs

    Directory of Open Access Journals (Sweden)

    Niall Holmes

    2015-01-01

    Full Text Available This paper investigates the effect of improper posttensioning of a 2-way spanning concrete slab subject to a central point load. Due to plate slippage alone, the support conditions only offered a 1-way spanning action which could have led to premature failure with dangerous consequences. Posttensioning can strengthen a flat slab against punching shear by controlling deflections and cracking under service loads compared with traditional punching shear reinforcing methods leading to more slender structures and economic solutions for longer spans. However, if the method is not properly applied, these thinner floor plates can fail in a brittle and sudden manner by punching at ultimate limit state and excessive deflection in serviceability. Concrete slabs containing traditional shear reinforcement performed adequately and demonstrated that the critical punching shear perimeter, defined as twice the depth of the slab, was confirmed from measured deflections and crack pattern analysis.

  5. Diffusion of radon through cracks in a concrete slab.

    Science.gov (United States)

    Landman, K A

    1982-07-01

    A mathematical model is developed to describe diffusion of radon through cracks or gaps in concrete slabs which are used in building foundations. As radon approaches the soil surface from underlying soil, it encounters a concrete slab. The radon will diffuse toward any air-filled cracks. The rate of exhalation through a portion of a cracked slab is determined and compared to the rate of exhalation from the same surface area of bare soil. In a typical case, this ratio is approx. 0.25. This is about a 20-fold increase to the ratio found when the concrete slab has no cracks. Therefore crack pathways are potentially a major source of indoor radon.

  6. The heterogeneous response method in slab geometry

    International Nuclear Information System (INIS)

    Villarino, E.A.; Stamm'ler, R.J.J.

    1984-01-01

    The heterogeneous response method (HRM) has been developed to calculate the multigroup flux in a heterogeneous system, e.g. a fuel assembly, without having to resort to dubious homogenization recipes. Here, the method is described in slab geometry in a manner that facilitates its computerization. By dividing the system into subsystems or nodes, say pin cells, two levels of calculation are created, which define a set of local problems and a global problem, respectively. In the local problem, collision probabilities are used to obtain for a node in vacuum, its response fluxes caused by sources and in-currents. They preserve the heterogeneous character of the node. In the global problem, the nodes are coupled by cosine currents. A suitable transformation reduces the number of two unknown currents per interface to one unknown per node, its total transmitted in-current. The global equation system thus becomes a set of three-point relations, which can be solved efficiently. In cases typical of fuel-assembly situations, the HRM produces fluxes that compare very well with the direct solution of the entire system by collision probabilities, though at a fraction of the computer cost. Extension of the method to 2- and 3-D systems is discussed. (author)

  7. Magnetoelectric sensor excitations in hexaferrite slabs

    Science.gov (United States)

    Zare, Saba; Izadkhah, Hessam; Somu, Sivasubramanian; Vittoria, Carmine

    2015-06-01

    We developed techniques for H- and E-field sensors utilizing single phase magnetoelectric (ME) hexaferrite slabs in the frequency range of 100 Hz to 10 MHz. Novel circuit designs incorporating both spiral and solenoid coils and single and multi-capacitor banks were developed to probe the physics and properties of ME hexaferrites and explore ME effects for sensor detections. Fundamental measurements of the anisotropic tensor elements of the magneto-electric coupling parameter were performed using these novel techniques. In addition, for H-field sensing experiments we measured sensitivity of about 3000 Vm-1/G using solenoid coils and 8000 Vm-1/G using spiral coils. For E-field, sensing the sensitivity was 10-4 G/Vm-1 and using single capacitor detector. Sensitivity for multi-capacitor detectors was measured to be in the order of 10-3 G/Vm-1 and frequency dependent exhibiting a maximum value at ˜1 MHz. Tunability of 0.1%-90% was achieved for tunable inductor applications using both single and multi-capacitors excitation. We believe that significant (˜106) improvements in sensitivity and tunability are feasible with simple modifications of the fabrication process.

  8. Calculation of shear strength of prestressed hollow core slabs by use of plastic theory

    DEFF Research Database (Denmark)

    Hoang, Linh Cao; Jørgensen, Henrik Brøner; Nielsen, Mogens Peter

    2014-01-01

    This paper deals with calculations of the shear capacity of precast, prestressed hollow core slabs. Such slabs are often used as floor systems in Building structures. A common way to produce hollow core slabs is to use the extrusion technique where long strips of slabs are extruded and thereafter...... saw-cut into units with the desirable length. For this reason, hollow core slabs are usually not shear reinforced and anchorage of the prestressing strands has to be established by bond. Hollow core slabs may therefore be more critical to shear and Anchorage failure than ordinary two-way spanning...... reinforced concrete slabs....

  9. Calculation of shear strength of prestressed hollow core slabs by use of plastic theory

    DEFF Research Database (Denmark)

    Hoang, Linh Cao; Jørgensen, H.G.; Nielsen, Mogens Peter

    2014-01-01

    Th is paper deals with calculations of the shear capacity of precast, prestressed hollow core slabs. Such slabs are often used as floor systems in building structures. A common way to produce hollow core slabs is to use the extrusion technique where long strips of slabs are extruded and thereafter...... saw-cut into units with the desirable length. For this reason, hollow core slabs are usually not shear reinforced and anchorage of the prestressing strands has to be established by bond. Hollow core slabs may therefore be more critical to shear and anchorage failure than ordinary two-way spanning...... reinforced concrete slabs....

  10. Broad-band beam buncher

    International Nuclear Information System (INIS)

    Goldberg, D.A.; Flood, W.S.; Arthur, A.A.; Voelker, F.

    1986-01-01

    This patent describes a broad-band beam buncher. This beam buncher consists of: a housing adapted to be eacuated, an electron gun in the housing for producing a beam of electrons, buncher means in the housing forming a buncher cavity which has an entrance opening for receiving the electron beam and an exit opening through which the electron beam passes out of the buncher cavity, a drift tube electrode in the buncher cavity and disposed between the entrance opening and the exit opening with first and second gaps between the drift tube electrode and the entrance and exit openings, the drift tube electrode which has a first drift space through which the electron beam passes in traveling between the entrance and exit openings, modulating means for supplying an ultrahigh frequeny modulating signal to the drift tube electrode for producing velocity modulation of the electrons in the electron beam as the electrons pass through the buncher cavity and the drift tube electrode between the entrance opening and the exit opening, drift space means in the housing forming a second drift space for receiving the velocity modulated electron beam from the exit opening, the velocity modulated electron beam being bunched as it passes along the second drift space, the drift space means has a discharge opening through which the electron beam is discharged from the second drift space after being bunched therein, the modulating means containing a signal source for producing an ultrahigh frequency signal, a transmission line connected between the signal source and the drift tube electrode, and terminating means connected to the drift tube electrode for terminating the transmission line in approximately its characteristic impedance to afford a broad response band with minimum 6 variations therein

  11. Variation of Seismic Velocity Structure around the Mantle Transition Zone and Conjecture of Deep Water Transport by Subducted Slabs

    Science.gov (United States)

    Tajima, F. C.; Stahler, S. C.; Ohtani, E.; Yoshida, M.; Sigloch, K.

    2011-12-01

    Seismic tomography models published in the past two decades determined common long-wavelength features of subducting plates as high velocity anomalies and upwelling plumes as low velocity anomalies, and have led to a new class of high-resolution three-dimensional (3D) modeling of global mantle convection with a link to tomography models [e.g., Becker and Boschi, 2002; Ritsema et al., 2007; Schuberth et al., 2009a,b]. However, even such high resolution numerical models do not account for the variation associated with different behaviors of subducting plates as they enter the mantle transition zone (MTZ), i.e., some flatten to form stagnant slabs with a large lateral extent and others descend further into the lower mantle. There are conventional interpretations applied for the cause of variation of the subducted slab behaviors, i.e., temperature difference due to different plate age, different geochemical compositions, different water content and subsequent possible reduction of viscosity etc., which could be taken as non-unique and somewhat equivocal. These parameters and conditions have been tested in two-dimensional numerical simulations, while the water content in the MTZ or the mechanisms of hydration and dehydration through subduction process are still in the realm of conjecture. Recent models of seismic P- and SH-wave velocities derived for the mantle structure beneath northeast China [Wang and Niu, 2010; Ye et al., 2011] using reflectivity synthetics with data from the dense Chinese networks of broadband seismic instruments, show a broader 660 km discontinuity (by about 30 to 70 km) and slower shear velocities above the MTZ than a global standard model iasp91 (Kennett and Engdahl, 1991). These features were interpreted with a mixture of different chemical properties which show delayed phase transformation, and effects of water above the flattened slab. Nonetheless, the SH-wave model has a structure similar to model TNA above the MTZ, which was derived for the

  12. Radon exhalation study from cement, cement slabs and concrete slabs with variation in fly ash

    International Nuclear Information System (INIS)

    Sharma, Nisha; Singh, Jaspal

    2012-01-01

    Fly ash is a waste product from coal-fired power plants. Fly ash has become a subject of world-wide interest in recent years because of its diverse uses, e.g. in the manufacture of concrete for building purposes, for the filling of underground cavities, or as a component of building material. The fly ash may contain enhanced levels of the natural radionuclides in the uranium and thorium series and by using the fly ash in building materials, the radiation levels in houses may thus be technologically enhanced. Because of its relatively high radionuclide contents (including 226 Ra), fly ash may, however, present a potential hazard to the population through its radon emanation, which would be highly undesirable. Since fly ash is frequently used as a building material, the idea of the experiment was to mix fly ash in different proportions in the cement in the powder form, cemented slabs and concrete slabs to study the combined behaviors. Alpha sensitive LR-115 type II plastic track detector, commonly known as Solid State Nuclear Track Detectors (SSNTDs), were used to measure the radon concentration. The alpha particles emitted from the radon causes the radiation damaged tracks. The chemical etching in NaOH at 60°C for about 90 minutes was done to reveal these latent tracks, which were then scanned and counted by an optical microscope of suitable magnification. By calculating the track density of registered tracks, the radon concentrations were determined. In case of cement in the powder form and in cemented slab, starting from the pure cement, fly ash was added up to 70% by weight. In this case the radon exhalation rate has increased by addition of fly ash in the cement and in case of concrete slabs by the addition of fly ash in the cement the radon exhalation increases up to 60% and then decreases. Therefore, on the basis of our investigations we concluded that in general radon exhalation rate increases with the addition of fly ash. (author)

  13. Punching of flat slabs supported on rectangular columns

    OpenAIRE

    Sagaseta, Juan; Tassinari, Luca; Fernández Ruiz, Miguel; Muttoni, Aurelio

    2014-01-01

    This paper investigates the structural behaviour of RC flat slabs supported on rectangular interior columns and the influence of the loading conditions (one or two-way bending) on their punching shear strength. The punching shear strength of slabs at rectangular columns can be lower than at equivalent square col- umns with a similar length of the control perimeter. This is due to a potential concentration of shear forces alongthecontrol perimeter. Some, but notall designformulas for punchingd...

  14. Slab2 - Updated Subduction Zone Geometries and Modeling Tools

    Science.gov (United States)

    Moore, G.; Hayes, G. P.; Portner, D. E.; Furtney, M.; Flamme, H. E.; Hearne, M. G.

    2017-12-01

    The U.S. Geological Survey database of global subduction zone geometries (Slab1.0), is a highly utilized dataset that has been applied to a wide range of geophysical problems. In 2017, these models have been improved and expanded upon as part of the Slab2 modeling effort. With a new data driven approach that can be applied to a broader range of tectonic settings and geophysical data sets, we have generated a model set that will serve as a more comprehensive, reliable, and reproducible resource for three-dimensional slab geometries at all of the world's convergent margins. The newly developed framework of Slab2 is guided by: (1) a large integrated dataset, consisting of a variety of geophysical sources (e.g., earthquake hypocenters, moment tensors, active-source seismic survey images of the shallow slab, tomography models, receiver functions, bathymetry, trench ages, and sediment thickness information); (2) a dynamic filtering scheme aimed at constraining incorporated seismicity to only slab related events; (3) a 3-D data interpolation approach which captures both high resolution shallow geometries and instances of slab rollback and overlap at depth; and (4) an algorithm which incorporates uncertainties of contributing datasets to identify the most probable surface depth over the extent of each subduction zone. Further layers will also be added to the base geometry dataset, such as historic moment release, earthquake tectonic providence, and interface coupling. Along with access to several queryable data formats, all components have been wrapped into an open source library in Python, such that suites of updated models can be released as further data becomes available. This presentation will discuss the extent of Slab2 development, as well as the current availability of the model and modeling tools.

  15. Shear and anchorage behaviour of fire exposed hollow core slabs

    OpenAIRE

    Fellinger, J.H.H.; Stark, J.; Walraven, J.C.

    2005-01-01

    The fire resistance of hollow core slabs is currently assessed considering flexural failure only. However, fire tests showed that shear or anchorage failure can also govern the load bearing behaviour. As the shear and anchorage capacity of these slabs rely on the tensile strength of the concrete, the load bearing capacity with respect to these failure modes decreases dramatically during fire due to the impact of thermal stresses. This paper presents a FE model for the shear and anchorage beha...

  16. Effect of Temperature Variation on Modal Frequency of Reinforced Concrete Slab and Beam in Cold Regions

    Directory of Open Access Journals (Sweden)

    Hanbing Liu

    2016-01-01

    Full Text Available Changes of modal frequencies induced by temperature variation can be more obvious than those caused by structural damage, which will lead to the false damage identification results. Therefore, quantifying the temperature effect on modal frequencies is a critical step to eliminate its interference in damage detection. Due to the nonuniform and time-dependent characteristics of temperature distribution, it is insufficient to obtain the reliable relationships between temperatures and modal frequencies using temperatures in air or at surface. In this paper, correlations between measured temperatures (air temperature, surface temperature, mean temperature, etc. and modal frequencies for the slab and beam are comparatively analyzed. And the quantitative models are constructed considering nonuniform temperature distribution. Firstly, the reinforced concrete slab and beam were constructed and placed outside the laboratory to be monitored. Secondly, the correlation coefficients between modal frequencies and three kinds of temperatures are calculated, respectively. Thirdly, simple linear regression models between mean temperature and modal frequencies are established for the slab and beam. Finally, five temperature variables are selected to construct the multiple linear regression models. Prediction results reveal that the proposed multiple linear regression models possess favorable accuracy to quantify the temperature effect on modal frequencies considering nonuniform temperature distribution.

  17. Recent progress in high-power slab lasers in Japan

    International Nuclear Information System (INIS)

    Fujii, Y.

    1988-01-01

    Recently, many solid-state lasers have been widely employed in Japanese industries, especially in the electronics industries for precise and reliable processing. To expand the use of solid-state lasers and to achieve higher processing speed, the authors are developing slab lasers of high power, high repetition rate, and high beam quality. Metal processing systems with optical fibers for large and complex 3-D work, multiwork station systems linked to only one laser with optical fibers, and compact x-ray sources for lithography are promising areas for such lasers. Surnitomo Metal Mining is growing Nd:GGG and Nd:YAG crystals 60 mm in diameter and 200 mm long. From 2 at.% Nd-doped GGG crystals without central core regions. The authors obtained two slab materials with dimensions of 35 X 9 X 192 and 55 X 15 X 213 mm/sup 3/. By using the smaller slab, they constructed a slab laser and obtained 370-W laser output power at 24-kW lamp input power and 10-pps repetition rate. Now they are constructing a 1-kW slab laser using the other larger size slab

  18. Strengthening of RC bridge slabs using CFRP sheets

    Directory of Open Access Journals (Sweden)

    Fahmy A. Fathelbab

    2014-12-01

    Full Text Available Many old structures became structurally insufficient to carry the new loading conditions requirements. Moreover, they suffer from structural degradation, reinforcement steel bars corrosion, bad weather conditions…etc. Many official authorities in several countries had recognized many old bridges and buildings as structurally deficient by today’s standards. Due to these reasons, structural strengthening became an essential requirement and different strengthening techniques appeared in market. Fiber Reinforced Polymer (FRP strengthening techniques established a good position among all other techniques, giving excellent structural results, low time required and moderate cost compared with the other techniques. The main purpose of this research is to study analytically the strengthening of a reinforced concrete bridge slabs due to excessive loads, using externally bonded FRP sheets technique. A commercial finite element program ANSYS was used to perform a structural linear and non-linear analysis for strengthened slab models using several schemes of FRP sheets. A parametric study was performed to evaluate analytically the effect of changing both FRP stiffness and FRP schemes in strengthening RC slabs. Comparing the results with control slab (reinforced concrete slab without strengthening it is obvious that attaching FRP sheets to the RC slab increases its capacity and enhances the ductility/toughness.

  19. Seismic anisotropy and mantle flow below subducting slabs

    Science.gov (United States)

    Walpole, Jack; Wookey, James; Kendall, J.-Michael; Masters, T.-Guy

    2017-05-01

    Subduction is integral to mantle convection and plate tectonics, yet the role of the subslab mantle in this process is poorly understood. Some propose that decoupling from the slab permits widespread trench parallel flow in the subslab mantle, although the geodynamical feasibility of this has been questioned. Here, we use the source-side shear wave splitting technique to probe anisotropy beneath subducting slabs, enabling us to test petrofabric models and constrain the geometry of mantle fow. Our global dataset contains 6369 high quality measurements - spanning ∼ 40 , 000 km of subduction zone trenches - over the complete range of available source depths (4 to 687 km) - and a large range of angles in the slab reference frame. We find that anisotropy in the subslab mantle is well characterised by tilted transverse isotropy with a slow-symmetry-axis pointing normal to the plane of the slab. This appears incompatible with purely trench-parallel flow models. On the other hand it is compatible with the idea that the asthenosphere is tilted and entrained during subduction. Trench parallel measurements are most commonly associated with shallow events (source depth slab. This may correspond to the shape preferred orientation of cracks, fractures, and faults opened by slab bending. Meanwhile the deepest events probe the upper lower mantle where splitting is found to be consistent with deformed bridgmanite.

  20. TECHNOLOGY FOR INSTALLATION OF REINFORCED CONCRETE FLOOR SLABS LIGHTENED BY CORE DRIVERS WITH PRELIMINARY REINFORCEMENT STRESS

    Directory of Open Access Journals (Sweden)

    S. N. Leonovich

    2015-01-01

    Full Text Available The paper presents technology for installation of floor slabs lightened by plastic core drivers which are preliminary stressed under construction conditions.  Efficiency of such constructive solution is justified by the action of preliminary concrete compression in the tensile zone while reducing structure dead weight due to void arrangement.  The paper provides classification of systems for preliminary stress and contains recommendations on selection of the system depending on peculiariar features of the designed construction.  Main products and materials required for execution of works , requirements to stressed wire rope reinforcement, its main characteristics have been considered in the paper.Principal diagram of the lightened preliminary stressed slab stipulates arrangement of so called  dummy caisson. Strands of reinforcement ropes are located within the framework of bars passing over supporting structures (over vertical bearing structures of  the framework and voids are formed in the cells between bars by laying hollow plastic items joined together by a cage. The paper presents technological sequence of operations required for arrangement of the lightened preliminary stressed slab, schemes for equipment arrangement and characteristics of the applied devices and units (pushing device for reinforcement ropes, hydraulic jack with delivery hydraulic pump, mixing station, injection pump and others.  Recommendations have been given for execution of works in cold weather. The paper considers problems pertaining to control quality of the materials and items which are supplied to a construction site and directly execution of works on preliminary stress of a cellular slab.The executed analysis of technology permits to conclude that it is characterized by high level of applicability for import substitution. It is necessary to consider the possibility to apply the technology at objects of various application while comparing it with other

  1. Energy Method Solution for the Vertical Deformation of Longitudinally Coupled Prefabricated Slab Track

    OpenAIRE

    Juanjuan Ren; Shijie Deng; Zhibin Jin; Junbin Yang; Xueyi Liu

    2017-01-01

    Upwarping on the longitudinally coupled prefabricated slab track system caused by the rising temperature is a common distress, which deteriorates the mechanical properties of the coupled slabs and the vertical stability of slabs. The objective of this paper is to quantify the upwarping deformation on the slab subjected to temperature force and to find out the influence of different factors on the upwarping phenomenon of the slabs. An analytical expression is deduced using energy method, and a...

  2. Identifying Broadband Rotational Spectra with Neural Networks

    Science.gov (United States)

    Zaleski, Daniel P.; Prozument, Kirill

    2017-06-01

    A typical broadband rotational spectrum may contain several thousand observable transitions, spanning many species. Identifying the individual spectra, particularly when the dynamic range reaches 1,000:1 or even 10,000:1, can be challenging. One approach is to apply automated fitting routines. In this approach, combinations of 3 transitions can be created to form a "triple", which allows fitting of the A, B, and C rotational constants in a Watson-type Hamiltonian. On a standard desktop computer, with a target molecule of interest, a typical AUTOFIT routine takes 2-12 hours depending on the spectral density. A new approach is to utilize machine learning to train a computer to recognize the patterns (frequency spacing and relative intensities) inherit in rotational spectra and to identify the individual spectra in a raw broadband rotational spectrum. Here, recurrent neural networks have been trained to identify different types of rotational spectra and classify them accordingly. Furthermore, early results in applying convolutional neural networks for spectral object recognition in broadband rotational spectra appear promising. Perez et al. "Broadband Fourier transform rotational spectroscopy for structure determination: The water heptamer." Chem. Phys. Lett., 2013, 571, 1-15. Seifert et al. "AUTOFIT, an Automated Fitting Tool for Broadband Rotational Spectra, and Applications to 1-Hexanal." J. Mol. Spectrosc., 2015, 312, 13-21. Bishop. "Neural networks for pattern recognition." Oxford university press, 1995.

  3. Reducing slab boundary artifacts in three‐dimensional multislab diffusion MRI using nonlinear inversion for slab profile encoding (NPEN)

    Science.gov (United States)

    Koopmans, Peter J.; Frost, Robert; Miller, Karla L.

    2015-01-01

    Purpose To propose a method to reduce the slab boundary artifacts in three‐dimensional multislab diffusion MRI. Methods Bloch simulation is used to investigate the effects of multiple factors on slab boundary artifacts, including characterization of residual errors on diffusion quantification. A nonlinear inversion method is proposed to simultaneously estimate the slab profile and the underlying (corrected) image. Results Correction results of numerical phantom and in vivo data demonstrate that the method can effectively remove slab boundary artifacts for diffusion data. Notably, the nonlinear inversion is also successful at short TR, a regimen where previously proposed methods (slab profile encoding and weighted average) retain residual artifacts in both diffusion‐weighted images and diffusion metrics (mean diffusion coefficient and fractional anisotropy). Conclusion The nonlinear inversion for removing slab boundary artifacts provides improvements over existing methods, particularly at the short TRs required to maximize SNR efficiency. Magn Reson Med 76:1183–1195, 2016. © 2015 The Authors. Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine. This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited. PMID:26510172

  4. Reducing slab boundary artifacts in three-dimensional multislab diffusion MRI using nonlinear inversion for slab profile encoding (NPEN).

    Science.gov (United States)

    Wu, Wenchuan; Koopmans, Peter J; Frost, Robert; Miller, Karla L

    2016-10-01

    To propose a method to reduce the slab boundary artifacts in three-dimensional multislab diffusion MRI. Bloch simulation is used to investigate the effects of multiple factors on slab boundary artifacts, including characterization of residual errors on diffusion quantification. A nonlinear inversion method is proposed to simultaneously estimate the slab profile and the underlying (corrected) image. Correction results of numerical phantom and in vivo data demonstrate that the method can effectively remove slab boundary artifacts for diffusion data. Notably, the nonlinear inversion is also successful at short TR, a regimen where previously proposed methods (slab profile encoding and weighted average) retain residual artifacts in both diffusion-weighted images and diffusion metrics (mean diffusion coefficient and fractional anisotropy). The nonlinear inversion for removing slab boundary artifacts provides improvements over existing methods, particularly at the short TRs required to maximize SNR efficiency. Magn Reson Med 76:1183-1195, 2016. © 2015 The Authors. Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine. This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited. © 2015 The Authors. Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine.

  5. Modeling radon entry into Florida slab-on-grade houses.

    Science.gov (United States)

    Revzan, K L; Fisk, W J; Sextro, R G

    1993-10-01

    Radon entry into a Florida house whose concrete slab is supported by a permeable concrete-block stem wall and a concrete footer is modeled. The slab rests on backfill material; the same material is used to fill the footer trench. A region of undisturbed soil is assumed to extend 10 m beyond and below the footer. The soil is assumed homogeneous and isotropic except for certain simulations in which soil layers of high permeability or radium content are introduced. Depressurization of the house induces a pressure field in the soil and backfill. The Laplace equation, resulting from Darcy's law and the continuity equation, is solved using a steady-state finite-difference model to determine this field. The mass-transport equation is then solved to obtain the diffusive and advective radon entry rates through the slab; the permeable stem wall; gaps at the intersections of the slab, stem wall, and footer; and gaps in the slab. These rates are determined for variable soil, backfill, and stem-wall permeability and radium content, slab-opening width and position, slab and stem-wall diffusivity, and water table depth. The variations in soil permeability and radium content include cases of horizontally stratified soil. We also consider the effect of a gap between the edge of the slab and the stem wall that restricts the passage of soil gas from the stem wall into the house. Calculations indicate that the total radon entry rate is relatively low unless the soil or backfill permeability or radium content is high. Variations in most of the factors, other than the soil permeability and radium content, have only a small effect on the total radon entry rate. However, for a fixed soil permeability, the total radon entry rate may be reduced by a factor of 2 or more by decreasing the backfill permeability, by making the stem wall impermeable and gap-free, (possibly by constructing a one-piece slab/stem-wall/footer), or by increasing the pressure in the interior of the stem wall (by

  6. Standing sausage modes in curved coronal slabs

    Science.gov (United States)

    Pascoe, D. J.; Nakariakov, V. M.

    2016-09-01

    Context. Magnetohydrodynamic waveguides such as dense coronal loops can support standing modes. The ratios of the periods of oscillations for different longitudinal harmonics depend on the dispersive nature of the waveguide and so may be used as a seismological tool to determine coronal parameters. Aims: We extend models of standing sausage modes in low β coronal loops to include the effects of loop curvature. The behaviour of standing sausage modes in this geometry is used to explain the properties of observed oscillations that cannot be accounted for using straight loop models. Methods: We perform 2D numerical simulations of an oscillating coronal loop, modelled as a dense slab embedded in a potential magnetic field. The loop is field-aligned and so experiences expansion with height in addition to being curved. Standing sausage modes are excited by compressive perturbations of the loop and their properties are studied. Results: The spatial profiles of standing sausage modes are found to be modified by the expanding loop geometry typical for flaring loops and modelled by a potential magnetic field in our simulations. Longitudinal harmonics of order n > 1 have anti-nodes that are shifted towards the loop apex and the amplitude of anti-nodes near the loop apex is smaller than those near the loop footpoints. Conclusions: We find that the observation of standing sausage modes by the Nobeyama Radioheliograph in a flaring coronal loop on 12 January 2000 is consistent with interpretation in terms of the global mode (n = 1) and third harmonic (n = 3). This interpretation accounts for the period ratio and spatial structure of the observed oscillations.

  7. Suppression of isotope scrambling in cell-free protein synthesis by broadband inhibition of PLP enymes for selective 15N-labelling and production of perdeuterated proteins in H2O

    International Nuclear Information System (INIS)

    Su Xuncheng; Loh, Choy-Theng; Qi Ruhu; Otting, Gottfried

    2011-01-01

    Selectively isotope labelled protein samples can be prepared in vivo or in vitro from selectively labelled amino acids but, in many cases, metabolic conversions between different amino acids result in isotope scrambling. The best results are obtained by cell-free protein synthesis, where metabolic enzymes are generally less active, but isotope scrambling can never be suppressed completely. We show that reduction of E. coli S30 extracts with NaBH 4 presents a simple and inexpensive way to achieve cleaner selective isotope labelling in cell-free protein synthesis reactions. The purpose of the NaBH 4 is to inactivate all pyridoxal-phosphate (PLP) dependent enzymes by irreversible reduction of the Schiff bases formed between PLP and lysine side chains of the enzymes or amino groups of free amino acids. The reduced S30 extracts retain their activity of protein synthesis, can be stored as well as conventional S30 extracts and effectively suppress conversions between different amino acids. In addition, inactivation of PLP-dependent enzymes greatly stabilizes hydrogens bound to α-carbons against exchange with water, minimizing the loss of α-deuterons during cell-free production of proteins from perdeuterated amino acids in H 2 O solution. This allows the production of highly perdeuterated proteins that contain protons at all exchangeable positions, without having to back-exchange labile deuterons for protons as required for proteins that have been synthesized in D 2 O.

  8. Participation in the broadband society in Denmark

    DEFF Research Database (Denmark)

    Falch, Morten; Henten, Anders; Skouby, Knud Erik

    2009-01-01

    passed the threshold set by the EU with respect to the relevance of initiating a discussion on the implementation of a universal service obligation on broadband. As documented in the paper, there are groups among primarily the elderly and the unemployed who do not have Internet access. Their own......The purpose of the paper is to provide an empirical overview of broadband developments in Denmark. The overview includes sections on coverage and penetration, connection speeds, retail prices, competition, interconnection prices, and residential access to Internet. The documentation shows...... explanation is not that they cannot afford it but that they don't need it. Still, there is an issue with respect to the participation in the broadband society, when an increasing part of communications in society is based on the Internet....

  9. Cost Analysis Of Broadband Service Delivery Systems

    Science.gov (United States)

    Dunn, Donald A.; Johnson, M. Gens

    1990-01-01

    Costs for active double-star fiber networks for local exchange service are compared with the costs of copper twisted-pair single-star networks and copper coaxial-line tree networks with switching at the customer's premises. For both existing and new neighborhoods, it appears that delivery of broadband services through tree networks (possibly using fiber) and delivery of narrow band services through copper twisted-pair star networks will be the minimum cost approach for low market penetrations of the broadband service market. For near 100 percent market penetrations there is relatively little difference in the costs of the two approaches.

  10. VT Total Broadband Availability by Census Block - 06-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201006 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2010. This...

  11. VT Cable Broadband Availability by Census Block - 06-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201006 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2010. This...

  12. VT Detailed Broadband Availability by Census Block -12-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201112 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2011. This...

  13. VT DSL Broadband Availability by Census Block - 06-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201106 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2011. This...

  14. VT Wireless Broadband Availability by Census Block - 06-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201106 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2011. This...

  15. VT Total Broadband Availability by Census Block - 12-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201012 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2010. This...

  16. VT Public Locations of Broadband Data - 06-2013

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201306 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2013. This...

  17. VT Total Broadband Availability by Census Block - 06-2013

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201306 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2013. This...

  18. VT DSL Broadband Availability by Census Block - 12-2012

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201212 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2012. This...

  19. VT Detailed Broadband Availability by Census Block - 06-2013

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201306 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2013. This...

  20. VT Wireline Broadband Availability by Census Block - 06-2013

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201306 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2013. This...

  1. VT Total Broadband Availability by Census Block - 06-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201106 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2011. This...

  2. VT Wireless Broadband Availability by Census Block - 06-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201006 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2010. This...

  3. VT DSL Broadband Availability by Census Block - 12-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201012 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2010. This...

  4. VT Total Broadband Availability by Census Block - 12-2012

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201212 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2012. This...

  5. VT Cable Broadband Availability by Census Block - 06-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201106 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2011. This...

  6. VT DSL Broadband Availability by Census Block - 06-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201006 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2010. This...

  7. VT Public Locations of Broadband Data - 12-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201112 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2011. This...

  8. VT Public Locations of Broadband Data - 12-2012

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201212 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2012. This...

  9. VT Total Broadband Availability by Census Block - 12-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201112 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2011. This...

  10. VT Public Locations of Broadband Data - 06-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201006 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2010. This...

  11. VT Detailed Broadband Availability by Census Block -12-2012

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201212 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2012. This...

  12. VT Wireline Broadband Availability by Census Block - 12-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201112 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2011. This...

  13. VT DSL Broadband Availability by Census Block - 12-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201112 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2011. This...

  14. VT Public Locations of Broadband Data - 06-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201106 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2011. This...

  15. VT DSL Broadband Availability by Census Block - 06-2013

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201306 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2013. This...

  16. VT Cable Broadband Availability by Census Block - 12-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201112 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2011. This...

  17. VT Cable Broadband Availability by Census Block - 06-2013

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201306 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2013. This...

  18. VT Wireline Broadband Availability by Census Block - 06-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201106 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2011. This...

  19. VT Wireline Broadband Availability by Census Block - 12-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201012 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2010. This...

  20. VT Detailed Broadband Availability by Census Block - 06-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201106 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2011. This...

  1. VT Wireline Broadband Availability by Census Block - 06-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201006 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2010. This...

  2. VT Public Locations of Broadband Data - 12-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201012 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2010. This...

  3. VT Detailed Broadband Availability by Census Block - 12-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201012 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2010. This...

  4. VT Wireless Broadband Availability by Census Block - 12-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201012 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2010. This...

  5. VT Detailed Broadband Availability by Census Block - 06-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201006 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2010. This...

  6. VT Cable Broadband Availability by Census Block - 12-2010

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201012 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2010. This...

  7. VT Wireless Broadband Availability by Census Block - 06-2013

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201306 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 6/30/2013. This...

  8. VT Wireline Broadband Availability by Census Block - 12-2012

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201212 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2012. This...

  9. VT Wireless Broadband Availability by Census Block - 12-2012

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201212 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2012. This...

  10. VT Wireless Broadband Availability by Census Block - 12-2011

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201112 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2011. This...

  11. VT Cable Broadband Availability by Census Block - 12-2012

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) The VTBB201212 VT Broadband Availability Dataset represents wireline and wireless 'broadband service' availability in VT as of 12/31/2012. This...

  12. Modeling radon entry into Florida slab-on-grade houses

    International Nuclear Information System (INIS)

    Revzan, K.L.; Fisk, W.J.; Sextro, R.G.

    1993-01-01

    Radon entry into a Florida house whose concrete slab is supported by a permeable concrete-block stem wall and a concrete footer is modeled. The slab rests on backfill material; the same material is used to fill the footer trench. A region of undisturbed soil is assumed to extend 10 m beyond and below the footer. The soil is assumed homogeneous and isotropic except for certain simulations in which soil layers of high permeability or radium content are introduced. Depressurization of the house induces a pressure field in the soil and backfill. The Laplace equation, resulting from Darcy's law and the continuity equation, is solved using a steady-state finite-difference model to determine this field. The mass-transport equation is then solved to obtain the diffusive and advective radon entry rates through the slab; the permeable stem wall; gaps at the intersections of the slab, stem wall, and footer; and gaps in the slab. These rates are determined for variable soil, backfill, and stem-wall permeability and radium content, slab-opening width and position, slab and stem-wall diffusivity, and water table depth. The variations in soil permeability and radium content include cases of horizontally stratified soil. We also consider the effect of a gap between the edge of the slab and the stem wall that restricts the passage of soil gas from the stem wall into the house. Calculations indicate that the total radon entry rate is relatively low unless the soil or backfill permeability or radium content is high. Variations in most of the factors, other than the soil permeability and radium content, have only a small effect on the total radon entry rate. However, for a fixed soil permeability, the total radon entry rate may be reduced by a factor of 2 or more by decreasing the backfill permeability, by making the stem wall impermeable and gap-free, (possibly by constructing a one-piece slab/stem-wall/footer), or by increasing the pressure in the interior of the stem wall

  13. Optical distortions in end-pumped zigzag slab lasers.

    Science.gov (United States)

    Tang, Bing; Zhou, Tangjian; Wang, Dan; Li, Mi

    2015-04-01

    Ray tracing is performed to investigate the optical distortions in the end-pumped, zigzag slab. Optical path differences caused by temperature, slab deformation, and stress birefringence are calculated under uniform pumping; the results show a steep edge in the width dimension and a thermal lens with an effective focal length as short as several meters in the thickness dimension. Dependence of depolarization on total internal reflection phase retardance as well as the slab's cut angle is studied by the Jones matrix technique; results show that although at the pumping power of 10 kW, the mean depolarization of the 2.5  mm×30  mm×150.2  mm Nd:YAG slab is generally below 3%, and it increases rapidly with pumping power. Besides, for the 0°- or 60°-cut slab, an optimal phase retardance range of 5° to 13° exists, in which the depolarization loss can be lower than 0.5%. Finally, experiments on temperature and depolarization measurements verify the numerical results.

  14. Sub-wavelength grating mode transformers in silicon slab waveguides.

    Science.gov (United States)

    Bock, Przemek J; Cheben, Pavel; Schmid, Jens H; Delâge, André; Xu, Dan-Xia; Janz, Siegfried; Hall, Trevor J

    2009-10-12

    We report on several new types of sub-wavelength grating (SWG) gradient index structures for efficient mode coupling in high index contrast slab waveguides. Using a SWG, an adiabatic transition is achieved at the interface between silicon-on-insulator waveguides of different geometries. The SWG transition region minimizes both fundamental mode mismatch loss and coupling to higher order modes. By creating the gradient effective index region in the direction of propagation, we demonstrate that efficient vertical mode transformation can be achieved between slab waveguides of different core thickness. The structures which we propose can be fabricated by a single etch step. Using 3D finite-difference time-domain simulations we study the loss, polarization dependence and the higher order mode excitation for two types (triangular and triangular-transverse) of SWG transition regions between silicon-on-insulator slab waveguides of different core thicknesses. We demonstrate two solutions to reduce the polarization dependent loss of these structures. Finally, we propose an implementation of SWG structures to reduce loss and higher order mode excitation between a slab waveguide and a phase array of an array waveguide grating (AWG). Compared to a conventional AWG, the loss is reduced from -1.4 dB to < -0.2 dB at the slab-array interface.

  15. Analysis and design of composite slab by varying different parameters

    Science.gov (United States)

    Lambe, Kedar; Siddh, Sharda

    2018-03-01

    Composite deck slabs are in demand because of its faster, lighter and economical construction work. Composite slab consists of cold formed deck profiled sheet and concrete either lightweight or normal. Investigation of shear behaviour of the composite slab is very complex. Shear bond strength depends on the various parameter such as a shape of sheeting, a thickness of the sheet, type of embossment and its frequency of use, shear stiffener or intermediate stiffener, type of load, an arrangement of load, length of shear span, the thickness of concrete and support friction etc. In present study finite element analysis is carried out with ABAQUS 6.13, a simply supported composite slab is considered for the investigation of the shear bond behaviour of the composite slab by considering variation in three different parameters, the shape of a sheet, thickness of sheet and shear span. Different shear spans of two different shape of cold formed deck profiled sheet i.e. with intermediate stiffeners and without intermediate stiffeners are considered with two different thicknesses (0.8 mm and 1.2 mm) for simulation. In present work, simulation of models has done for static loading with 20 mm mesh size is considered.

  16. Broadband: An Insight and Its Benefits | Devardhi | Science ...

    African Journals Online (AJOL)

    It is viewed by some as a double-edged sword: networking could promote economic development, yet electronic commerce also has the potential to displace local businesses. The paper focuses on defining broadband, identifying and assessing the benefits of broadband technologies. Although broadband technologies are ...

  17. Wireless Fidelity (Wi-Fi) Broadband Network Technology: An ...

    African Journals Online (AJOL)

    Wireless Fidelity (Wi-Fi) broadband network technology has made tremendous impact in the growth of broadband wireless networks. There exists today several Wi-Fi access points that allow employees, partners and customers to access corporate data from almost anywhere and anytime. Wireless broadband networks are ...

  18. Designing Broadband Access Networks with Triple Redundancy

    DEFF Research Database (Denmark)

    Pedersen, Jens Myrup; Riaz, Muhammad Tahir; Knudsen, Thomas Phillip

    2005-01-01

    An architecture is proposed for designing broadband access networks, which offer triple redundancy to the end users, resulting in networks providing connectivity even in case of any two independent node or line failures. Two physically independent connections are offered by fiber, and the last...

  19. 77 FR 36903 - Accelerating Broadband Infrastructure Deployment

    Science.gov (United States)

    2012-06-20

    ... the Nation's global competitiveness in the 21st century, driving job creation, promoting innovation, and expanding markets for American businesses. Broadband access also affords public safety agencies... infrastructure has been deployed in a vast majority of communities across the country, today too many areas still...

  20. WIRELESS FIDELITY (Wi-Fi) BROADBAND NETWORK ...

    African Journals Online (AJOL)

    ES Obe

    categorized into two types: fixed and mobile wireless. The broadband fixed wireless network technologies .... 3.0 WIRELESS FIDELITYF (Wi-Fi). NETWORK IMPLEMENTATION. A Wi-Fi enabled device such as a PC, game .... Amateur radio, video senders, and cordless phones, can cause significant additional interference.

  1. Broadband Heterodyne SIS Spectrometer Prototype: First Results

    Science.gov (United States)

    Rice, F.; LeDuc, H.; Harris, A.; Hu, S.; Sumner, M.; Zmuidzinas, J.

    2004-01-01

    The broadband heterodyne SIS receiver system described elsewhere (reference 1) has been assembled and tested both in the laboratory and during two observing runs on the Cassegrain focus of the 10 meter telescope at the Caltech Submillimeter Observatory on Mauna Kea, Hawaii. Here we present a brief summary of the initial results.

  2. BROADBAND TRAVELLING WAVE SEMICONDUCTOR OPTICAL AMPLIFIER

    DEFF Research Database (Denmark)

    2010-01-01

    Broadband travelling wave semiconductor optical amplifier (100, 200, 300, 400, 800) for amplification of light, wherein the amplifier (100, 200, 300, 400, 800) comprises a waveguide region (101, 201, 301, 401, 801) for providing confinement of the light in transverse directions and adapted...

  3. Broadband multiresonator quantum memory-interface.

    Science.gov (United States)

    Moiseev, S A; Gerasimov, K I; Latypov, R R; Perminov, N S; Petrovnin, K V; Sherstyukov, O N

    2018-03-05

    In this paper we experimentally demonstrated a broadband scheme of the multiresonator quantum memory-interface. The microwave photonic scheme consists of the system of mini-resonators strongly interacting with a common broadband resonator coupled with the external waveguide. We have implemented the impedance matched quantum storage in this scheme via controllable tuning of the mini-resonator frequencies and coupling of the common resonator with the external waveguide. Proof-of-principal experiment has been demonstrated for broadband microwave pulses when the quantum efficiency of 16.3% was achieved at room temperature. By using the obtained experimental spectroscopic data, the dynamics of the signal retrieval has been simulated and promising results were found for high-Q mini-resonators in microwave and optical frequency ranges. The results pave the way for the experimental implementation of broadband quantum memory-interface with quite high efficiency η > 0.99 on the basis of modern technologies, including optical quantum memory at room temperature.

  4. Development of Flexible Link Slabs using Ductile Fiber Reinforced Concrete

    DEFF Research Database (Denmark)

    Lárusson, Lárus Helgi

    Civil engineering structures with large dimensions, such as multi-span bridges, overpasses and viaducts, are typically equipped with mechanical expansion joints. These joints allow the individual spans of the structure to undergo unrestrained deformations due to thermal expansions and load......, it is suggested to replace the mechanical expansion joint and implement a flexible, precast ductile concrete link slab element between simply supported bridge spans. To design and analyze the suggested link slab element, each constituent of the element, i.e. the structural reinforcement and the cementitious...... and under cyclic loading. The findings from the investigations on bond-slip, tension stiffening and tension strengthening are used in Chapter 5 as inputfor the design and analysis of the loaddeformation response and the crack development of a prefabricated flexible link slab elements potentially connecting...

  5. Abrupt tectonics and rapid slab detachment with grain damage.

    Science.gov (United States)

    Bercovici, David; Schubert, Gerald; Ricard, Yanick

    2015-02-03

    A simple model for necking and detachment of subducting slabs is developed to include the coupling between grain-sensitive rheology and grain-size evolution with damage. Necking is triggered by thickened buoyant crust entrained into a subduction zone, in which case grain damage accelerates necking and allows for relatively rapid slab detachment, i.e., within 1 My, depending on the size of the crustal plug. Thick continental crustal plugs can cause rapid necking while smaller plugs characteristic of ocean plateaux cause slower necking; oceanic lithosphere with normal or slightly thickened crust subducts without necking. The model potentially explains how large plateaux or continental crust drawn into subduction zones can cause slab loss and rapid changes in plate motion and/or induce abrupt continental rebound.

  6. Band-notched ultrawide band antenna loaded with ferrite slab

    Science.gov (United States)

    Wang, Hao; Zong, Weihua; Sun, Nian X.; Lin, Hwaider; Li, Shandong

    2017-05-01

    In this paper, a novel technique to design a band-notched UWB antenna by using Yttrium Iron Garnet (YIG) ferrite is proposed. A printed slot UWB antenna with size of 21mm×26 mm×0.8 mm is adopted as a basic antenna. A piece of ferrite slab with size of 5 mm×10 mm×2 mm is attached on the feeding layer of the antenna to achieve band-notched characteristics. The measured -10 dB bandwidth of the antenna without ferrite slab is 2.91-10.98 GHz. With loading of ferrite slab, the bandwidth turns to 2.73-5.12 and 5.87-10.78 GHz. A band notch of 5.12- 5.87 GHz is achieved to filter WLAN 5 GHz (5.15-5.825 GHz) band. The proposed technique has virtue of easy fabrication and keeping antenna miniaturization.

  7. Optimal Material Layout - Applied on Reinforced Concrete Slabs

    DEFF Research Database (Denmark)

    Dollerup, Niels; Jepsen, Michael S.; Damkilde, Lars

    2015-01-01

    This paper introduces a general, finite-element-based optimisation tool for improving the material layout of concrete structures. The application presented is general and exemplified by material optimisation of reinforced concrete slabs. By utilising the optimisation tool, it is possible to deter......This paper introduces a general, finite-element-based optimisation tool for improving the material layout of concrete structures. The application presented is general and exemplified by material optimisation of reinforced concrete slabs. By utilising the optimisation tool, it is possible...... to determine the optimal material layout of a slab in the ultimate load state, based on simple inputs such as outer geometry, boundary conditions, multiple load cases and design domains. The material layout of the optimal design can either be fully orthotropic or isotropic, or a combination with a predefined...

  8. Criticality of neutron transport in a slab with finite reflectors

    International Nuclear Information System (INIS)

    Pao, C.V.

    1978-01-01

    The purpose of this paper is to investigate the subcriticality and the supercriticality for the neutron transport in a slab which is surrounded by two finite reflectors. The mathematical problem is to determine when the coupled boundary-value problem has or has no positive solution. It is shown under some explicit conditions on the material properties of the transport mediums and the size of the slab length that the coupled problem has a unique solution which insures the subcriticality of the system. It is also shown under some different conditions on the same physical quantities that the system cannot have a nonnegative solution when there is an external source, and it only has the trivial solution when there is no source in the system. This conclusion leads to the supercriticality of the system. Both upper and lower bounds for the critical length of the slab are explicitly given

  9. Microinstabilities in a radially contracting inhomogeneous cylindrical plasma slab

    International Nuclear Information System (INIS)

    Deutsch, R.; Kaeppeler, H.J.

    1980-07-01

    In order to study the development of microinstabilities in a collapsing cylindrical plasma sheath, corresponding to the situations in a z-pinch or a plasma focus, the dispersion relation for electromagnetic perturbations is derived with the aid of a newly established slab-model for an inhomogeneous, radially contracting plasma. In contrast to previously used slab-models, the orientation of the electric field is in direction of the cylinder axis and the azimuthal magnetic field is induced by the current flowing through the cylindrical plasma slab. The Vlasov equation is used together with the Krook collision term in order to include the influence of collisions. The results of this theory presented in this report will be used to calculate the growth of drift instabilities in the compression phase of a plasma focus, and shall serve as a basis for further development of a more general dispersion relation including runaway-effects. (orig.)

  10. IMPROVEMENT OF SLAB REHEATING PROCESS AT USIMINAS THROUGH MATHEMATICAL SIMULATION

    Directory of Open Access Journals (Sweden)

    Antônio Adel dos Santos

    2012-09-01

    Full Text Available Basic characteristics and application examples of the mathematical simulator for reheating process in walking-beam type furnaces, that has been developed and applied to Usiminas plate mill line at Ipatinga, are shown in this paper. This is a bi-dimensional mathematical model solved by the finite volume method, validated by temperature measurements inside the slab during heating and coded as a visual tool. Among these applications, the following can be highlighted: (i determination of suitable furnace zone temperatures and residence times for processing steels by accelerated cooling technology; (ii determination of slab average temperature at discharging as well as at each zone exit, supplying data to be fed to the automation system at the comissioning stage; (iii analyses of slab thermal distribution through the reheating process, enabling operational optimization

  11. Cost Effectiveness of Precast Reinforced Concrete Roof Slabs

    Science.gov (United States)

    Parskiy, N. D.; Molodtsov, M. V.; Molodtsova, V. E.

    2017-11-01

    Engineers always seek to free interior space from intermediate supporting elements. Nowadays plants, being at the forefront of technology, produce a new generation of exclusive patented prefabricated reinforced concrete elements with a high load-bearing capacity, excellent heat resistance characteristics combined with the aesthetics and beauty. It is a system of Seagull Gabbiano prestressed roof slabs for the spans of 12m - 40m. The article shows the advantages of the Seagull slabs over conventional precast reinforced concrete and metal roof trusses. It also gives the analysis of the technical and economic indices of design and construction of a building with the Seagull slabs depending on the size of spans to cover. The use of structural systems with increased spans allows for the modern buildings and structures of prefabricated reinforced concrete with enhanced functionality and aesthetics alongside with a wide range of planning solutions.

  12. Investigation on Blast Resistance of Precast Reinforced Concrete Floor Slab

    Science.gov (United States)

    Bonora, Nicola; Gentile, Domenico; Iannitti, Gianluca; Ruggiero, Andrew; Testa, Gabriel; Bernabei, Manuele; Cassioli, Luigi; Grossi, Silvana

    2017-06-01

    The knowledge of the effective blast resistance of civil infrastructures is a fundamental information for risk assessment and modelling consequences of terrorist attack in high population density urban environment. In this work, blast resistance of precast reinforced concrete floor slab, commonly used for commercial parking, was investigated performing blast tests, detonating bare explosive charge of RDX 80-20 in contact with the slab. The charge mass, and the stand-off distance, was varied in order to generate different damage extents, from visible to fully breached condition. Numerical simulations were performed considering all slab structural elements. Failure model for concrete was calibrated on breach size and shape observed in the experiments. The explosive and blast wave-structure interaction were simulated using arbitrary Lagrangian-Eulerian method (ALE) and particle blast method (PBM) for comparison.

  13. Radon Sub-slab Suctioning System Integrated in Insulating Layer

    DEFF Research Database (Denmark)

    Rasmussen, Torben Valdbjørn

    2013-01-01

    This poster presents a new radon sub-slab suctioning system. This system makes use of a grid of horizontal pressurised air ducts located within the lower part of the rigid insulation layer of the ground floor slab. For this purpose a new system of prefabricated lightweight elements is introduced....... The system is shown to be effective in preventing radon from polluting the indoor air by introducing low pressure in the horizontal grid of air ducts. How to implement and use the system in an effective way is described....

  14. Seismic Behaviour of Masonry Vault-Slab Structures

    International Nuclear Information System (INIS)

    Chesi, Claudio; Butti, Ferdinando; Ferrari, Marco

    2008-01-01

    Spandrel walls typically play a structural role in masonry buildings, transferring load from a slab to the supporting vault. Some indications are given in the literature on the behaviour of spandrels under the effect of vertical loads, but little attention is given to the effect coming from lateral forces acting on the building. An opportunity to investigate this problem has come from the need of analyzing a monumental building which was damaged by the Nov. 24, 2004 Val Sabbia earthquake in the north of Italy. The finite element model set up for the analysis of the vault-spandrel-slab system is presented and the structural role resulting for the spandrels is discussed

  15. Dynamic evolution of aluminum nanoparticle impacted by RDX slab

    Science.gov (United States)

    Wang, Ning; Cheng, Jie; Li, Haibo; Du, Fang; Li, Chenghu; Hu, Jianjiang; Peng, Jinhua

    2018-03-01

    A modified ReaxFF force field was used to study dynamic deformation of Al nanoparticles (ANPs) and chemical evolution of RDX/Al mixtures. When small ANPs impact RDX crystal planes, the interaction between RDX and Al at the initial stage does not affect the order of shock-induced anisotropic response of RDX crystal and different thickness of alumina shell on ANPs exhibits different capacity to resist structural deformation. When Al slab with 30 wt% is coated with a 3 nm thickness of alumina, Al slab exhibits inert characteristics and provides high compression condition to enhance decomposition of RDX molecules during the initial impact stage.

  16. Concrete mixtures with high-workability for ballastless slab tracks

    Directory of Open Access Journals (Sweden)

    Olga Smirnova

    2017-10-01

    Full Text Available The concrete track-supporting layer and the monolithic concrete slab of ballastless track systems are made in-situ. For this reason the concrete mixtures of high workability should be used. Influence of the sand kind, the quartz microfiller fineness and quantity as well as quantity of superplasticizer on workability of fresh concrete and durability of hardened concrete is shown. The compositions of the high-workability concrete mixtures with lower consumption of superplasticizer are developed. The results of the research can be recommended for high performance concrete of ballastless slab track.

  17. Spalling tests on embedded cores and slabs: A comparative study

    Directory of Open Access Journals (Sweden)

    Pimienta P.

    2013-09-01

    Full Text Available A comparative analysis of the spalling of (a cores made of 3 concrete mixes embedded into 3 slabs made of the 3 same concrete mixes; and (b 3 reference slabs made again of the same 3 concrete mixes has been made. Samples have been exposed to the French Increased HydroCarbon temperature curve. Results confirm that concrete spalling phenomena is not only related to the material properties. Concrete spalling is also very much influenced by the geometry of the samples.

  18. Spalling of concrete: A synthesis of experimental tests on slabs

    Directory of Open Access Journals (Sweden)

    Taillefer Nicolas

    2013-09-01

    Full Text Available The article reviews the results of many commercial or research tests carried out in CSTB on middle size concrete slabs. They concern 22 concrete slabs, made of normal and high strength concrete, for a rather wide range of thickness and compressive strength classes. Test procedures and a synthesis of main results are presented in order to provide deeper understanding of near-reality conditions of concrete structures. The tests concerned both new and existing tunnels. Results are detailed in relation with main parameters that are identified as impacting spalling in previous studies, such as concrete composition, concrete properties and specimen size.

  19. Analog optical computing by half-wavelength slabs

    Science.gov (United States)

    Zangeneh-Nejad, Farzad; Khavasi, Amin; Rejaei, Behzad

    2018-01-01

    A new approach to perform analog optical differentiation is presented using half-wavelength slabs. First, a half-wavelength dielectric slab is used to design a first order differentiator. The latter works properly for both major polarizations, in contrast to our previously design based on Brewster effect (Youssefi et al., 2016). Inspired by the proposed dielectric differentiator, and by exploiting the unique features of graphene, we further design and demonstrate a reconfigurable and highly miniaturized differentiator using a half-wavelength plasmonic graphene film. To the best of our knowledge, our proposed graphene-based differentiator is even smaller than the most compact differentiator presented so far.

  20. Bayesian Inference for Structured Spike and Slab Priors

    DEFF Research Database (Denmark)

    Andersen, Michael Riis; Winther, Ole; Hansen, Lars Kai

    2014-01-01

    Sparse signal recovery addresses the problem of solving underdetermined linear inverse problems subject to a sparsity constraint. We propose a novel prior formulation, the structured spike and slab prior, which allows to incorporate a priori knowledge of the sparsity pattern by imposing a spatial...... Gaussian process on the spike and slab probabilities. Thus, prior information on the structure of the sparsity pattern can be encoded using generic covariance functions. Furthermore, we provide a Bayesian inference scheme for the proposed model based on the expectation propagation framework. Using...

  1. Permanent storage of light in a double-slab structure

    Science.gov (United States)

    Chen, Jiangwei; Yuan, Guoxuan; Tao, Zhikuo

    2017-11-01

    In this paper, we shall demonstrate firstly that a normal incidence can be totally reflected from a slab made of active metamaterial with purely-imaginary-impedance. Then we shall predict that a localized steady state of electromagnetic wave dependent on initial input can exist in a double-slab structure, which relates to the non null solution of equations formed by electromagnetic field boundary conditions. These results may provide a feasible way to effectively treat loss and/or gain problems and thus store electromagnetic wave (light) permanently at room temperature. In addition, our work indicates that metamaterials with purely-imaginary-impedance may enable remarkable electromagnetic phenomena and merit further study.

  2. Punching Shear Behavior of Continuous Bubbled Reinforced Reactive Powder Concrete Slab

    Directory of Open Access Journals (Sweden)

    Mohammad Redha K. Mahmood

    2017-03-01

    Full Text Available This paper presents an experimental investigation on punching shear behavior of continuous bubbled reinforced Reactive Powder Concrete (RPC slabs. Bubbled slab is one of the various types of voided slabs. It consists of bubbles placed inside a concrete slab which will reduce the self-weight of the structure by about 35% (Tina Lai 2009. On the other hand, using RPC make it possible for structural member to have smaller dimensions due to the great strength of this type of concrete. In this study, these two method to increase the building spaces dimensions by reducing self-weigh of the structure by using bubbled slabs and to decrease the structural members' dimensions by using RPC have been investigated together. To study the punching shear behavior of continuous bubbled flat slabs such as the ultimate load carrying capacity, central deflection and slabs crack pattern at the ultimate load, nine different types of slabs were tested. The parameters of the study were type of concrete (RPC and Normal Concrete (NC, bubbles diameter to slab thickness ratio (D/t of (0.6 and 0.7, bubbles location (at all slab area, started from distance D and 1.5D from the center slab and solid slab. The test results show that the crack pattern and ultimate load capacity as well as maximum deflection depends on all of the mentioned parameters, were by increasing (D/t ratio the ultimate load capacity increases about (6.49 and 9.58% for slabs with bubbles started at distance 2D and 3D, respectively. But in the slabs with bubbles at all slab area the ultimate load and the maximum deflection decreases about (6.63 and 9.47% and (7.96 and 6.84% for RPC and NC slabs, respectively. Also, the solid slab increases the ultimate load about (5.28% compare to bubbled slab at all area. It was found that by removing bubbles from center of the slab at distance 2D and 3D the ultimate load will increase about (14.72 and 8.76%, respectively for slabs with (D/t = 0.6 compare to slabs with

  3. Efficient Implementation of a Symbol Timing Estimator for Broadband PLC.

    Science.gov (United States)

    Nombela, Francisco; García, Enrique; Mateos, Raúl; Hernández, Álvaro

    2015-08-21

    Broadband Power Line Communications (PLC) have taken advantage of the research advances in multi-carrier modulations to mitigate frequency selective fading, and their adoption opens up a myriad of applications in the field of sensory and automation systems, multimedia connectivity or smart spaces. Nonetheless, the use of these multi-carrier modulations, such as Wavelet-OFDM, requires a highly accurate symbol timing estimation for reliably recovering of transmitted data. Furthermore, the PLC channel presents some particularities that prevent the direct use of previous synchronization algorithms proposed in wireless communication systems. Therefore more research effort should be involved in the design and implementation of novel and robust synchronization algorithms for PLC, thus enabling real-time synchronization. This paper proposes a symbol timing estimator for broadband PLC based on cross-correlation with multilevel complementary sequences or Zadoff-Chu sequences and its efficient implementation in a FPGA; the obtained results show a 90% of success rate in symbol timing estimation for a certain PLC channel model and a reduced resource consumption for its implementation in a Xilinx Kyntex FPGA.

  4. Efficient Implementation of a Symbol Timing Estimator for Broadband PLC

    Directory of Open Access Journals (Sweden)

    Francisco Nombela

    2015-08-01

    Full Text Available Broadband Power Line Communications (PLC have taken advantage of the research advances in multi-carrier modulations to mitigate frequency selective fading, and their adoption opens up a myriad of applications in the field of sensory and automation systems, multimedia connectivity or smart spaces. Nonetheless, the use of these multi-carrier modulations, such as Wavelet-OFDM, requires a highly accurate symbol timing estimation for reliably recovering of transmitted data. Furthermore, the PLC channel presents some particularities that prevent the direct use of previous synchronization algorithms proposed in wireless communication systems. Therefore more research effort should be involved in the design and implementation of novel and robust synchronization algorithms for PLC, thus enabling real-time synchronization. This paper proposes a symbol timing estimator for broadband PLC based on cross-correlation with multilevel complementary sequences or Zadoff-Chu sequences and its efficient implementation in a FPGA; the obtained results show a 90% of success rate in symbol timing estimation for a certain PLC channel model and a reduced resource consumption for its implementation in a Xilinx Kyntex FPGA.

  5. Telemicroscopy stations for telepathology based on broadband and ISDN connections.

    Science.gov (United States)

    Schwarzmann, P; Schmid, J; Schnörr, C; Strässle, G; Witte, S

    1995-01-01

    Telemicroscopy equipment is a key tool to perform Telepathology successfully. It allows the local separation of the microscope with the tissue samples from the investigating pathologist. The Telemicroscopy stations presented provide the user with a full access to the functions such as scanning stage, focus, illumination and magnification selection of a remote microscope. One system applies as communication link a broadband video conference net of the German Telekom with full realtime capabilities and color TV-image quality. As this network provides adequate interfaces for video and computer net signals, it is well suited to establish within a short time interval a very comfortable Telemicroscopy connection without the development of additional equipment. As the broadband network is expensive the application is economically restricted to special applications. The other system relies on the narrow band connections of the ISDN telephone network. This design is inexpensive with respect to data transmission and is available nearly worldwide everywhere. But on the other hand this strategy is limited concerning realtime capabilities. To reduce these limitations to an acceptable level intelligent coding and operation concepts of the stations have to be developed.

  6. Management of broadband technology and innovation policy, deployment, and use

    CERN Document Server

    Choudrie, Jyoti

    2013-01-01

    When one considers broadband, the Internet immediately springs to mind. However, broadband is impacting society in many ways. For instance, broadband networks can be used to deliver healthcare or community related services to individuals who don't have computers, have distance as an issue to contend with, or don't use the internet. Broadband can support better management of scarce energy resources with the advent of smart grids, enables improved teleworking capacity and opens up a world of new entertainment possibilities. Yet scholarly examinations of broadband technology have so far examin

  7. Slab fluid release: localized in space and time

    Science.gov (United States)

    John, T.; Gussone, N. C.; Podladchikov, Y. Y.

    2012-12-01

    As subducting oceanic plates descend into the Earth's mantle, increasing pressures and temperatures lead to the progressive destabilization of hydrous mineral phases and the release of H2O-rich fluids. Some fraction of these fluids ascend into the overlying mantle wedge, inducing partial melting, and their "chemical freight" is thought to contribute to the distinctive chemical signature of the resulting arc magmas. Field evidences suggest that channelized fluid flow may be the dominant mechanism for intra-slab fluid flow. Along their pathways within slabs, these fluids can trigger mineral reactions and produce chemical changes in rocks with which they interact. However, the spatial and temporal scales of this fluid flow remain largely unknown. We employed the Ca and Li isotope systems on a fossil high-pressure fluid pathway and its associated reaction halo (Chinese Tianshan), formed at ~70 km depth during subduction of a coherent oceanic slab, allowing us to constrain the fluid flux, fluid source and the duration of the fluid-rock interaction. In the reaction halo, the degree of eclogitization along with Ca concentration increases towards the vein. A high fluid flux is required to obtain the observed Ca increase and changes in δ44/40Ca. The Ca isotope composition indicate mixing of two distinct Ca sources, the wall-rock blueschist and an external fluid source, the latter of which is enriched in heavy Ca isotopes. The relatively high δ44/40Ca (>1.3‰) of the infiltrating fluid is suggestive of partially hydrated slab mantle as the fluid source. Alternatively, Ca derived from MORB, (0.7 to 0.9‰) and AOC (0.6 to 1.0‰) might evolve towards heavier Ca isotope values while it is ascending through the slab and reacting with wall-rocks and forming carbonates, which are usually associated with the flow structures. This is because calcium carbonate precipitation preferentially removes light Ca from the fluid while the residual fluid will get heavier proportional to

  8. Local government broadband policies for areas with limited Internet access

    Directory of Open Access Journals (Sweden)

    Yoshio Arai

    2014-03-01

    Full Text Available Despite their wide diffusion in developed countries, broadband services are still limited in areas where providing them is not profitable for private telecom carriers. To address this, many local governments in Japan have implemented broadband deployment projects subsidized by the national government. In this paper, we discuss local government broadband policies based on survey data collected from municipalities throughout the country. With the support of national promotion policies, broadband services were rapidly introduced to most local municipalities in Japan during the 2000s. Local government deployment policies helped to reduce the number of areas with no broadband access. A business model based on the Indefeasible Right of Use (IRU contract between a private telecom carrier and a local government has been developed in recent years. Even local governments without the technical capacity to operate a broadband business can introduce broadband services into their territory using the IRU business model.

  9. Investigation of approach slab and its settlement for roads and bridges.

    Science.gov (United States)

    2014-01-01

    Approach slabs serve as a transitional system between an approach road and a bridge. Settlement of bridge approach slabs and their : supporting backfill has been experienced by more than ten Departments of Transportation throughout the United States....

  10. Punching Shear in Steel Fibre Reinforced Concrete Slabs Without Traditional Reinforcement

    Science.gov (United States)

    Tan, K. H.; Venkateshwaran, A.

    2017-09-01

    The punching shear capacity of steel fibre reinforced concrete (SFRC) slabs without traditional steel bar reinforcement was investigated by conducting central point-load tests on twelve square slabs. The test parameters covered fibres with different multi-hook ends, concrete compressive strength, reinforcing index and slab thickness. The statistical performance of two existing models for the prediction of punching shear capacity of SFRC slabs without traditional reinforcement was examined. The load carrying capacity of these slabs were also assessed using the yield line theory. It is noted that the slabs failed primarily in flexure and the yield line theory predicted the load carrying capacities of the slabs most accurately. The reason for a flexural failure in SFRC slabs without steel bars is attributed to the lesser energy required in the propagation of an existing flexural cracks than in the creation of a new circumferential cracks around the column face.

  11. Parametric excitation of drift waves in a sheared slab geometry

    International Nuclear Information System (INIS)

    Vranjes, J.; Weiland, J.

    1992-01-01

    The threshold for parametric excitation of drift waves in a sheared slab geometry is calculated for a pump wave that is a standing wave along the magnetic field, using the Hasegawa-Mima nonlinearity. The shear damping is counteracted by the parametric coupling and the eigenvalue problem is solved analytically using Taylor's strong coupling approximation. (au)

  12. Characterization of pore structure of PHEMA-based slabs

    Czech Academy of Sciences Publication Activity Database

    Hradil, Jiří; Horák, Daniel

    2005-01-01

    Roč. 62, - (2005), s. 1-9 ISSN 1381-5148 R&D Projects: GA MŠk LN00A065 Institutional research plan: CEZ:AV0Z4050913 Keywords : poly(2-hydroxyethyl methacrylate) * ethylene dimethacrylate * slabs Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.565, year: 2005

  13. Lower Bound Limit Analysis Of Slabs With Nonlinear Yield Criteria

    DEFF Research Database (Denmark)

    Krabbenhøft, Kristian; Damkilde, Lars

    2002-01-01

    A finite element formulation of the limit analysis of perfectly plastic slabs is given. An element with linear moment fields for which equilibrium is satisfied exactly is used in connection with an optimization algorithm taking into account the full nonlinearity of the yield criteria. Both load...

  14. Analysis of Concrete Slabs Subject to Concentrated Loads | Albrecht ...

    African Journals Online (AJOL)

    A simplified procedure for the calculation of the additional reinforcement which is required under concentrated loads acting on concrete slabs is provided. The introduced method can also be used for the treatment of line loads. Conditions for the application of this procedure are stated and tables for necessary design values ...

  15. Enhancement of polarizabilities of cylinders with cylinder-slab resonances.

    Science.gov (United States)

    Xiao, Meng; Huang, Xueqin; Liu, H; Chan, C T

    2015-02-02

    If an object is very small in size compared with the wavelength of light, it does not scatter light efficiently. It is hence difficult to detect a very small object with light. We show using analytic theory as well as full wave numerical calculation that the effective polarizability of a small cylinder can be greatly enhanced by coupling it with a superlens type metamaterial slab. This kind of enhancement is not due to the individual resonance effect of the metamaterial slab, nor due to that of the object, but is caused by a collective resonant mode between the cylinder and the slab. We show that this type of particle-slab resonance which makes a small two-dimensional object much "brighter" is actually closely related to the reverse effect known in the literature as "cloaking by anomalous resonance" which can make a small cylinder undetectable. We also show that the enhancement of polarizability can lead to strongly enhanced electromagnetic forces that can be attractive or repulsive, depending on the material properties of the cylinder.

  16. Optimization of design formulations for reinforced concrete slabs ...

    African Journals Online (AJOL)

    The predictions for flexural requirement in singly reinforced concrete slabs and sections have been assessed using the minimum weight approach and mathematical programming. Results indicate that although the predictions in the codes are safe; they are quite conservative, expensive and encourage although the ...

  17. Bayesian Inference for Structured Spike and Slab Priors

    DEFF Research Database (Denmark)

    Andersen, Michael Riis; Winther, Ole; Hansen, Lars Kai

    2014-01-01

    Sparse signal recovery addresses the problem of solving underdetermined linear inverse problems subject to a sparsity constraint. We propose a novel prior formulation, the structured spike and slab prior, which allows to incorporate a priori knowledge of the sparsity pattern by imposing a spatial...

  18. Designing Meta Material Slabs Exhibiting Negative Refraction Using Topology Optimization

    DEFF Research Database (Denmark)

    Christiansen, Rasmus Ellebæk; Sigmund, O.

    2016-01-01

    This paper proposes a topology optimization based approach for designing meta materials exhibiting a desired negative refraction with high transmission at a given angle of incidence and frequency. The approach considers a finite slab of meta material consisting of axis-symmetric designable unit...

  19. Structural response of reinforced concrete slabs to impulsive loads

    International Nuclear Information System (INIS)

    Florence, A.L.

    1977-01-01

    The structure treated here is a clamped circular slab of reinforced concrete. The loading is a rectangular pulse uniformly distributed over a central area. The practical value of this problem is that it probably represents a most severe loading case for bending response among more realistic cases, because it replaces the local loaded area with a circular area at the slab center, and because it replaces the pulse with a rectangular pulse of the same peak pressure and impulse. In the theoretical treatment the pulse is assumed to produce plastic deformations large enough to neglect elastic deformation but small enough to neglect membrane action. Yielding of the reinforced concrete slab is assumed to be governed by the Johansen criterion and the associated flow rule. For simplicity, the analysis is restricted to isotropic slabs with top and bottom steel reinforcement arranged to provide the same yield moment magnitude for positive and negative curvature changes. A consequence of the assumed rigid-perfectly plastic behavior is that the deformation modes may be considered as simple mechanism governed by a yield circle. Moreover, the yield circle is stationary while the constant pressure is being applied and expands to the support once the pressure is removed. After the yield circle has arrived at the support, the remaining deformation occurs in the static collapse mode. The principal results are explicit simple formulas for permanent central deflection in terms of pressure, duration, loaded area radius, and plate properties (radius, density, yield moment)

  20. Tensor-guided fitting of subduction slab depths

    Science.gov (United States)

    Bazargani, Farhad; Hayes, Gavin P.

    2013-01-01

    Geophysical measurements are often acquired at scattered locations in space. Therefore, interpolating or fitting the sparsely sampled data as a uniform function of space (a procedure commonly known as gridding) is a ubiquitous problem in geophysics. Most gridding methods require a model of spatial correlation for data. This spatial correlation model can often be inferred from some sort of secondary information, which may also be sparsely sampled in space. In this paper, we present a new method to model the geometry of a subducting slab in which we use a data‐fitting approach to address the problem. Earthquakes and active‐source seismic surveys provide estimates of depths of subducting slabs but only at scattered locations. In addition to estimates of depths from earthquake locations, focal mechanisms of subduction zone earthquakes also provide estimates of the strikes of the subducting slab on which they occur. We use these spatially sparse strike samples and the Earth’s curved surface geometry to infer a model for spatial correlation that guides a blended neighbor interpolation of slab depths. We then modify the interpolation method to account for the uncertainties associated with the depth estimates.

  1. Use of fiber reinforced concrete for concrete pavement slab replacement.

    Science.gov (United States)

    2014-03-01

    Unlike ordinary concrete pavement, replacement concrete slabs need to be open to traffic within 24 hours (sooner in : some cases). Thus, high early-strength concrete is used; however, it frequently cracks prematurely as a result of high : heat of hyd...

  2. Concrete slabs under a combination of loads in shear

    NARCIS (Netherlands)

    Lantsoght, E.O.L.; Van der Veen, C.; Walraven, J.C.

    2013-01-01

    Previous experimental research at Delft University of Technology indicated an increased shear capacity of slabs under concentrated loads as a function of decreasing distance to the adjacent line support. Expressions have been derived for this increase, including the definition of an appropriate

  3. Collisional Effect On Magnetosonic Solitons In A Dusty Plasma Slab ...

    African Journals Online (AJOL)

    An analytical investigation of collisional effect on magnetosonic solitons in a dusty plasma slab is presented. We have derived and presented solutions of nonlinear magetohydrodynamic equations for a warm dusty magnetoplasma. It is observed that, our work could be considered a general case for magnetosonic solutions ...

  4. Behavior of the equivalent slab thickness over three European stations

    Czech Academy of Sciences Publication Activity Database

    Mosert, M.; Magdaleno, S.; Burešová, Dalia; Altadill, D.; Gende, M.; Gularte, E.; Scida, L.

    2013-01-01

    Roč. 51, č. 4 (2013), s. 677-682 ISSN 0273-1177 Institutional support: RVO:68378289 Keywords : Ionospheric slab thickness * F2- layer peak * TEC * European stations Subject RIV: DG - Athmosphere Sciences, Meteorology Impact factor: 1.238, year: 2013 http://www.sciencedirect.com/science/article/pii/S0273117712003754

  5. A differentiated plane wave: its passage through a slab

    International Nuclear Information System (INIS)

    Hannay, J H; Nye, J F

    2013-01-01

    Differentiating a monochromatic uniform plane electromagnetic wavefield with respect to its direction produces, from a field that is completely lacking in localized specific features, one that contains a straight vortex-like line, a ‘C-line’ of defined circular polarization. There is also a second separate C-line of opposite handedness; indeed, in a sense, a straight line of every polarization is realized. Because of its primitive construction it is analytically simple to study the passage of a differentiated wave obliquely through a plane interface into a medium of different refractive index, to trace its C-line. This was done in an earlier paper. Here we extend the method to passage through a parallel-sided transparent slab. There are multiple reflections within the slab, as in a Fabry–Pérot interferometer. The exiting wave, as a single differentiated plane wave, has a straight oblique C-line. Inside the slab, and in front of it, there is wave interference. The result is a coiled, helix-like, C-line in front of the slab and another inside it. The two coils wrap around separate hyperboloids of one sheet, like cooling towers. The emerging straight C-line is shifted (with respect to a C-line in a notional undisturbed incident plane wave) both in the plane of incidence and transversely to it, and the second C-line behaves similarly. The analysis is exact and could be extended in a straightforward way to a general stratified medium. (paper)

  6. Fringe integral equation method for a truncated grounded dielectric slab

    DEFF Research Database (Denmark)

    Jørgensen, Erik; Maci, S.; Toccafondi, A.

    2001-01-01

    The problem of scattering by a semi-infinite grounded dielectric slab illuminated by an arbitrary incident TMz polarized electric field is studied by solving a new set of “fringe” integral equations (F-IEs), whose functional unknowns are physically associated to the wave diffraction processes...

  7. Emplacement of the Kodiak batholith and slab-window migration

    Science.gov (United States)

    Farris, David W.; Haeussler, P.; Friedman, R.; Paterson, Scott R.; Saltus, R.W.; Ayuso, R.

    2006-01-01

    The Kodiak batholith is one of the largest, most elongate intrusive bodies in the forearc Sanak-Baranof plutonic belt located in southern Alaska. This belt is interpreted to have formed during the subduction of an oceanic spreading center and the associated migration of a slab window. Individual plutons of the Kodiak batholith track the location and evolution of the underlying slab window. Six U/Pb zircon ages from the axis of the batholith exhibit a northeastward-decreasing age progression of 59.2 ± 0.2 Ma at the southwest end to 58.4 ± 0.2 Ma at the northeast tip. The trench-parallel rate of age progression is within error of the average slab-window migration rate for the entire Sanak-Baranof belt (~19 cm/yr). Structural relationships, U/Pb ages, and a model of new gravity data indicate that magma from the Kodiak batholith ascended 5-10 km as a northeastward-younging series of 1-8-km-diameter viscoelastic diapirs. Individual plutons ascended by multiple emplacement mechanisms including downward flow, collapse of wall rock, stoping, and diking. Stokes flow xenolith calculations suggest ascent rates of 5-100 m/yr and an effective magmatic viscosity of 107-108 Pa s. Pre-existing structural or lithologic heterogeneities did not dominantly control the location of the main batholith. Instead, its location was determined by migration of the slab window at depth. 

  8. Shear and anchorage behaviour of fire exposed hollow core slabs

    NARCIS (Netherlands)

    Fellinger, J.

    2005-01-01

    The fire resistance of hollow core slabs is currently assessed considering flexural failure only. However, fire tests show that shear or anchorage failure can also govern the load bearing behaviour. This paper is based on the dissertation by the author1 and discusses existing and new fire tests. It

  9. Study of global stability of tall buildings with prestressed slabs

    Directory of Open Access Journals (Sweden)

    L. A. Feitosa

    Full Text Available The use of prestressed concrete flat slabs in buildings has been increasing in recent years in the Brazilian market. Since the implementation of tall and slender buildings a trend in civil engineering and architecture fields, arises from the use of prestressed slabs a difficulty in ensuring the overall stability of a building without beams. In order to evaluate the efficiency of the main bracing systems used in this type of building, namely pillars in formed "U" in elevator shafts and stairs, and pillars in which the lengths are significantly larger than their widths, was elaborated a computational models of fictional buildings, which were processed and analyzed using the software CAD/TQS. From the variation of parameters such as: geometry of the pillars, thick slabs, characteristic strength of the concrete, reduceofthe coefficient of inertia for consideration of non-linearities of the physical elements, stiffness of the connections between slabs and pillars, among others, to analyze the influence of these variables on the overall stability of the building from the facing of instability parameter Gama Z, under Brazilian standard NBR 6118, in addition to performing the processing of building using the P-Delta iterative calculation method for the same purpose.

  10. Some consequences of the subduction of young slabs

    NARCIS (Netherlands)

    England, P.; Wortel, R.

    The negative buoyancy force exerted by a subducting oceanic slab depends on its descent velocity, and strongly on its age. For lithosphere close to thermal equilibrium, this force dominates by a large margin the resisting forces arising from friction on the plate boundary and compositional buoyancy.

  11. Puzzling features of western Mediterranean tectonics explained by slab dragging

    Science.gov (United States)

    Spakman, Wim; Chertova, Maria V.; van den Berg, Arie.; van Hinsbergen, Douwe J. J.

    2018-02-01

    The recent tectonic evolution of the western Mediterranean region is enigmatic. The causes for the closure of the Moroccan marine gateway prior to the Messinian salinity crisis, for the ongoing shortening of the Moroccan Rif and for the origin of the seismogenic Trans-Alboran shear zone and eastern Betics extension are unclear. These puzzling tectonic features cannot be fully explained by subduction of the east-dipping Gibraltar slab in the context of the regional relative plate motion frame. Here we use a combination of geological and geodetic data, as well as three-dimensional numerical modelling of subduction, to show that these unusual tectonic features could be the consequence of slab dragging—the north to north-eastward dragging of the Gibraltar slab by the absolute motion of the African Plate. Comparison of our model results to patterns of deformation in the western Mediterranean constrained by geological and geodetic data confirm that slab dragging provides a plausible mechanism for the observed deformation. Our results imply that the impact of absolute plate motion on subduction is identifiable from crustal observations. Identifying such signatures elsewhere may improve the mantle reference frame and provide insights on subduction evolution and associated crustal deformation.

  12. Slab flattening and exhumation of the Eastern Cordillera of Colombia

    Science.gov (United States)

    Siravo, G.; Faccenna, C.; Fellin, M. G.; Herman, F.; Becker, T. W.; Molin, P.

    2017-12-01

    Mountain belt topography is shaped by processes acting at different time scales and depths, from the surface down to the crust and mantle. In particular, subduction dynamics is expected to strongly affect upper plate topography. Here, we present the case of the Eastern Cordillera (EC) in Colombia as a case history for dynamic mantle forcing from a subduction zone on the upper plate topography. The EC is an active double-vergent fold and thrust belt formed during the Cenozoic by the inversion of a Mesozoic rift, and topography there has grown up to 5000 m (Cocuy Sierra). The EC is located far ( 500 km) from the trench where the Nazca slab subducts below the South American plate. Tomography and seismicity show the presence of a flat slab subduction north of 5° N (Chiarabba et al., 2016). Slab flattening may have occurred transitionally from 10 to 5 Ma shutting down the arc volcanism (Wagner et al., 2017). We reconstruct the exhumation of the EC based on previously published and new thermochronologic data collected in the area of the Cocuy Sierra. Results of this analysis show notably fast exhumation rates since Late Miocene. We also analyze the likely contributions to topography and show that neither the present-day crustal thickness nor the cumulative shortening in the Cenozoic as extracted form balanced cross section can isostatically explain the present day topography. We conclude that fast EC exhumation and uplift are driven by mantle dynamics and likely occurred during the recent episode of slab flattening.

  13. Slab melting and magma formation beneath the southern Cascade arc

    Science.gov (United States)

    Walowski, Kristina J.; Wallace, Paul J.; Clynne, Michael A.; Rasmussen, D.J.; Weis, D.

    2016-01-01

    The processes that drive magma formation beneath the Cascade arc and other warm-slab subduction zones have been debated because young oceanic crust is predicted to largely dehydrate beneath the forearc during subduction. In addition, geochemical variability along strike in the Cascades has led to contrasting interpretations about the role of volatiles in magma generation. Here, we focus on the Lassen segment of the Cascade arc, where previous work has demonstrated across-arc geochemical variations related to subduction enrichment, and H-isotope data suggest that H2O in basaltic magmas is derived from the final breakdown of chlorite in the mantle portion of the slab. We use naturally glassy, olivine-hosted melt inclusions (MI) from the tephra deposits of eight primitive (MgO>7 wt%) basaltic cinder cones to quantify the pre-eruptive volatile contents of mantle-derived melts in this region. The melt inclusions have B concentrations and isotope ratios that are similar to mid-ocean ridge basalt (MORB), suggesting extensive dehydration of the downgoing plate prior to reaching sub-arc depths and little input of slab-derived B into the mantle wedge. However, correlations of volatile and trace element ratios (H2O/Ce, Cl/Nb, Sr/Nd) in the melt inclusions demonstrate that geochemical variability is the result of variable addition of a hydrous subduction component to the mantle wedge. Furthermore, correlations between subduction component tracers and radiogenic isotope ratios show that the subduction component has less radiogenic Sr and Pb than the Lassen sub-arc mantle, which can be explained by melting of subducted Gorda MORB beneath the arc. Agreement between pMELTS melting models and melt inclusion volatile, major, and trace element data suggests that hydrous slab melt addition to the mantle wedge can produce the range in primitive compositions erupted in the Lassen region. Our results provide further evidence that chlorite-derived fluids from the mantle portion of the

  14. Inverse Doppler Effects in Broadband Acoustic Metamaterials.

    Science.gov (United States)

    Zhai, S L; Zhao, X P; Liu, S; Shen, F L; Li, L L; Luo, C R

    2016-08-31

    The Doppler effect refers to the change in frequency of a wave source as a consequence of the relative motion between the source and an observer. Veselago theoretically predicted that materials with negative refractions can induce inverse Doppler effects. With the development of metamaterials, inverse Doppler effects have been extensively investigated. However, the ideal material parameters prescribed by these metamaterial design approaches are complex and also challenging to obtain experimentally. Here, we demonstrated a method of designing and experimentally characterising arbitrary broadband acoustic metamaterials. These omni-directional, double-negative, acoustic metamaterials are constructed with 'flute-like' acoustic meta-cluster sets with seven double meta-molecules; these metamaterials also overcome the limitations of broadband negative bulk modulus and mass density to provide a region of negative refraction and inverse Doppler effects. It was also shown that inverse Doppler effects can be detected in a flute, which has been popular for thousands of years in Asia and Europe.

  15. Techno-Economics of Residential Broadband Deployment

    DEFF Research Database (Denmark)

    Sigurdsson, Halldor Matthias

    2007-01-01

    as much profit as possible from their previous investments. However, the operators are not restricted by these considerations, and they will often choose a fiber-to-the home solution (FTTH, Fiber-to-the-Home), which will offer a far more substantial data capacity in the long run. The choice of the proper...... broadband deployment strategy is depending on a complexed set of parameters, and there is a demand for precise techno-economic cost models estimating financial feasibility. The existing cost models do not consider the dynamic developments in the market caused by competition. The PhD thesis has a profound...... analysis of the transmission requirements of future broadband services and the technical parameters with importance for the deployment strategy. The framework of the project is interdisciplinary and combines a solid technological knowledge about telecom networks and services with economic and telecom...

  16. An ultra-broadband multilayered graphene absorber

    KAUST Repository

    Amin, Muhammad

    2013-01-01

    An ultra-broadband multilayered graphene absorber operating at terahertz (THz) frequencies is proposed. The absorber design makes use of three mechanisms: (i) The graphene layers are asymmetrically patterned to support higher order surface plasmon modes that destructively interfere with the dipolar mode and generate electromagnetically induced absorption. (ii) The patterned graphene layers biased at different gate voltages backedup with dielectric substrates are stacked on top of each other. The resulting absorber is polarization dependent but has an ultra-broadband of operation. (iii) Graphene\\'s damping factor is increased by lowering its electron mobility to 1000cm 2=Vs. Indeed, numerical experiments demonstrate that with only three layers, bandwidth of 90% absorption can be extended upto 7THz, which is drastically larger than only few THz of bandwidth that can be achieved with existing metallic/graphene absorbers. © 2013 Optical Society of America.

  17. Broadband active electrically small superconductor antennas

    Science.gov (United States)

    Kornev, V. K.; Kolotinskiy, N. V.; Sharafiev, A. V.; Soloviev, I. I.; Mukhanov, O. A.

    2017-10-01

    A new type of broadband active electrically small antenna (ESA) based on superconducting quantum arrays (SQAs) has been proposed and developed. These antennas are capable of providing both sensing and amplification of broadband electromagnetic signals with a very high spurious-free dynamic range (SFDR)—up to 100 dB (and even more)—with high sensitivity. The frequency band can range up to tens of gigahertz, depending on Josephson junction characteristic frequency, set by fabrication. In this paper we review theoretical and experimental studies of SQAs and SQA-based antenna prototypes of both transformer and transformer-less types. The ESA prototypes evaluated were fabricated using a standard Nb process with critical current density 4.5 kA cm-2. Measured device characteristics, design issues and comparative analysis of various ESA types, as well as requirements for interfaces, are reviewed and discussed.

  18. Field demonstration of new bridge approach slab designs and performance : [research project capsule].

    Science.gov (United States)

    2008-10-01

    A normal bridge approach slab in Louisiana is a reinforced concrete slab. It connects : the bridge deck to the adjacent paved roadway. Its intended functions are: : 1. To span the void that may develop below the slab due to soil erosion or : embankme...

  19. High-power diode-pumped Tm:YLF slab laser

    CSIR Research Space (South Africa)

    Schellhorn, M

    2009-06-01

    Full Text Available The aim is to develop a high-power Tm:YLF slab laser which can be utilized to pump a Ho slab laser. A 68 W Tm:YLF slab laser was recently presented in [1] pumped from one end by a single 6-bar stack delivering ~300 W of pump power. In this work, we...

  20. Application of yield line theory in pre-cast waffle slab | Akinyele ...

    African Journals Online (AJOL)

    Analysis of precast waffle slabs have concentrated on the rib portions, while the slab portion were left unanalyzed. This has led to cracks or outright failure of the slab portions due to under reinforcement. This paper proposed the use of yield line theory in solving this problem. Yield line theory was adopted to develop a ...

  1. Broadband Spectroscopy of Nanoporous-Gold Promoter

    Directory of Open Access Journals (Sweden)

    S. K. Nakatani

    2014-02-01

    Full Text Available The efficiency of UV photocatalysis on TiO2 particles was increased by mixing TiO2 particles with nanoporous gold (NPG with pore diameters of 10–40 nm. This means that NPG acts as a promoter in the photocatalytic reaction of TiO2. Broadband spectroscopic results from millimeter wave to ultra violet of NPG membrane are discussed to estimate plasmonic effect on the catalysis.

  2. Energy efficiency in future wireless broadband networks

    CSIR Research Space (South Africa)

    Masonta, MT

    2012-10-01

    Full Text Available , and will require unique energy efficient solutions. For instance, an MS may be battery-powered, and the relevant energy efficient solution would include switching-off the display and minimizing signalling overhead (e.g. sleep mode). Meanwhile energy efficient... solution for the BS may include the intelligent sleep mode policies when the number of users and the traffic load decreases [3]. Due to the growing demand for advanced broadband wireless technologies and services, research in green radio solutions...

  3. Enhanced broadband optical transmission in metallized woodpiles

    DEFF Research Database (Denmark)

    Malureanu, Radu; Alabastri, A.; Cheng, W.

    2011-01-01

    We present an optimized isotropic metal deposition technique used for covering three-dimensional polymer structures with a 50 nm smooth silver layer. The technology allows fast and isotropic coating of complex 3D dielectric structures with thin silver layers. Transmission measurements of 3D...... metallized woodpiles reveal a new phenomenon of enhanced optical transmission in broadband range (up to 300 nm) in the near IR....

  4. Broadband luminescence in liquid-solid transition

    CERN Document Server

    Achilov, M F; Trunilina, O V

    2002-01-01

    Broadband luminescence (BBL) intensity behavior in liquid-solid transition in polyethyleneglycol-600 has been established. Oscillation of BBL intensity observed in liquid-polycrystal transition are not found to observed in liquid-amorphous solid transition. It is shown that application of the theory of electron state tails to interpretation of BBL spectral properties in liquids demands restriction. BBL spectroscopy may be applied for optimization of preparation of polymers with determined properties. (author)

  5. Diagonalizing sensing matrix of broadband RSE

    International Nuclear Information System (INIS)

    Sato, Shuichi; Kokeyama, Keiko; Kawazoe, Fumiko; Somiya, Kentaro; Kawamura, Seiji

    2006-01-01

    For a broadband-operated RSE interferometer, a simple and smart length sensing and control scheme was newly proposed. The sensing matrix could be diagonal, owing to a simple allocation of two RF modulations and to a macroscopic displacement of cavity mirrors, which cause a detuning of the RF modulation sidebands. In this article, the idea of the sensing scheme and an optimization of the relevant parameters will be described

  6. The Spike-and-Slab Lasso Generalized Linear Models for Prediction and Associated Genes Detection.

    Science.gov (United States)

    Tang, Zaixiang; Shen, Yueping; Zhang, Xinyan; Yi, Nengjun

    2017-01-01

    Large-scale "omics" data have been increasingly used as an important resource for prognostic prediction of diseases and detection of associated genes. However, there are considerable challenges in analyzing high-dimensional molecular data, including the large number of potential molecular predictors, limited number of samples, and small effect of each predictor. We propose new Bayesian hierarchical generalized linear models, called spike-and-slab lasso GLMs, for prognostic prediction and detection of associated genes using large-scale molecular data. The proposed model employs a spike-and-slab mixture double-exponential prior for coefficients that can induce weak shrinkage on large coefficients, and strong shrinkage on irrelevant coefficients. We have developed a fast and stable algorithm to fit large-scale hierarchal GLMs by incorporating expectation-maximization (EM) steps into the fast cyclic coordinate descent algorithm. The proposed approach integrates nice features of two popular methods, i.e., penalized lasso and Bayesian spike-and-slab variable selection. The performance of the proposed method is assessed via extensive simulation studies. The results show that the proposed approach can provide not only more accurate estimates of the parameters, but also better prediction. We demonstrate the proposed procedure on two cancer data sets: a well-known breast cancer data set consisting of 295 tumors, and expression data of 4919 genes; and the ovarian cancer data set from TCGA with 362 tumors, and expression data of 5336 genes. Our analyses show that the proposed procedure can generate powerful models for predicting outcomes and detecting associated genes. The methods have been implemented in a freely available R package BhGLM (http://www.ssg.uab.edu/bhglm/). Copyright © 2017 by the Genetics Society of America.

  7. Assimilating lithosphere and slab history in 4-D Earth models

    Science.gov (United States)

    Bower, Dan J.; Gurnis, Michael; Flament, Nicolas

    2015-01-01

    We develop methods to incorporate paleogeographical constraints into numerical models of mantle convection. Through the solution of the convection equations, the models honor geophysical and geological data near the surface while predicting mantle flow and structure at depth and associated surface deformation. The methods consist of four constraints determined a priori from a plate history model: (1) plate velocities, (2) thermal structure of the lithosphere, (3) thermal structure of slabs in the upper mantle, and (4) velocity of slabs in the upper mantle. These constraints are implemented as temporally- and spatially-dependent conditions that are blended with the solution of the convection equations at each time step. We construct Earth-like regional models with oceanic and continental lithosphere, trench migration, oblique subduction, and asymmetric subduction to test the robustness of the methods by computing the temperature, velocity, and buoyancy flux of the lithosphere and slab. Full sphere convection models demonstrate how the methods can determine the flow associated with specific tectonic environments (e.g., back-arc basins, intraoceanic subduction zones) to address geological questions and compare with independent data, both at present-day and in the geological past (e.g., seismology, residual topography, stratigraphy). Using global models with paleogeographical constraints we demonstrate (1) subduction initiation at the Izu-Bonin-Mariana convergent margin and flat slab subduction beneath North America, (2) enhanced correlation of model slabs and fast anomalies in seismic tomography beneath North and South America, and (3) comparable amplitude of dynamic and residual topography in addition to improved spatial correlation of dynamic and residual topography lows.

  8. Seismicity Structure of the Downgoing Nazca Slab in Northern Chile

    Science.gov (United States)

    Sippl, C.; Schurr, B.

    2017-12-01

    We applied an automatized earthquake detection and location algorithm to 8 years of continuous seismic data from the IPOC network in Northern Chile, located in the forearc between about 18.5°S and 24°S. The resulting seismicity catalog contains more than 113k double-difference relocated earthquake hypocenters and features a completeness magnitude around 2.8. Despite the occurrence of two megathrust earthquakes with vigorous aftershock seismicity in the studied time period (the 2007 Tocopilla and the 2014 Iquique earthquakes), >60% of the retrieved seismicity is located in a highly active band of intermediate-depth earthquakes (80-120 km deep) within the downgoing Nazca slab.We obtain a triple seismic zone in the updip part of the slab, with the three parallel dipping planes corresponding to the plate interface, the oceanic Moho (ca. 8 km below the interface) and a third band in the mantle lithosphere 26-28 km beneath the slab top. The plate interface seismicity terminates abruptly at a depth of 55 km. At about 80-90 km depth, the remaining two planes of seismicity then merge into the single, 20 km thick cluster of vigorous seismicity mentioned above, which terminates at 120 km depth. This cluster is located directly beneath the volcanic arc and shows a pronounced kink in the slab dipping angle. Intra-slab seismicity is most likely related to metamorphic dehydration reactions, hence our high-resolution earthquake distribution can be considered a map of metamorphic reactions (although a possibly incomplete one, since not all reactions necessarily invoke seismicity). By correlating this distribution with isotherms from thermal models as well as geophysical imaging results from previous studies, we attempt to get a glimpse at the processes that produce the different patches of intraslab seismicity at intermediate depths.

  9. Broadband MAS NMR spectroscopy in the low-power limit

    Science.gov (United States)

    Sanders, Kevin J.; Pell, Andrew J.; Wegner, Sebastian; Grey, Clare P.; Pintacuda, Guido

    2018-04-01

    We investigate the performance of broadband adiabatic inversion pulses in the high-power (short high-powered adiabatic pulse, SHAP) and low-power (single-sideband-selective adiabatic pulse, S3AP) RF regimes on a spin system subjected to large anisotropic interactions. We show by combined experimental results and spin dynamics simulations that when the magic-angle spinning rate exceeds 100 kHz S3APs begin outperforming SHAPs. This is especially true for low-gamma nuclei, such as 6 Li in paramagnetic Li-ion battery materials. Finally, we show how S3APs can be improved by combining multiple waveforms sweeping over multiple sidebands simultaneously, in order to produce inverted sideband profiles free from intensity biasing.

  10. Shear wave velocities in the Pampean flat-slab region from Rayleigh wave tomography: Implications for slab and upper mantle hydration

    Science.gov (United States)

    Porter, Ryan; Gilbert, Hersh; Zandt, George; Beck, Susan; Warren, Linda; Calkins, Josh; Alvarado, Patricia; Anderson, Megan

    2012-11-01

    The Pampean flat-slab region, located in central Argentina and Chile between 29° and 34°S, is considered a modern analog for Laramide flat-slab subduction within western North America. Regionally, flat-slab subduction is characterized by the Nazca slab descending to ˜100 km depth, flattening out for ˜300 km laterally before resuming a more "normal" angle of subduction. Flat-slab subduction correlates spatially with the track of the Juan Fernandez Ridge, and is associated with the inboard migration of deformation and the cessation of volcanism within the region. To better understand flat-slab subduction we combine ambient-noise tomography and earthquake-generated surface wave measurements to calculate a regional 3D shear velocity model for the region. Shear wave velocity variations largely relate to changes in lithology within the crust, with basins and bedrock exposures clearly defined as low- and high-velocity regions, respectively. We argue that subduction-related hydration plays a significant role in controlling shear wave velocities within the upper mantle. In the southern part of the study area, where normal-angle subduction is occurring, the slab is visible as a high-velocity body with a low-velocity mantle wedge above it, extending eastward from the active arc. Where flat-slab subduction is occurring, slab velocities increase to the east while velocities in the overlying lithosphere decrease, consistent with the slab dewatering and gradually hydrating the overlying mantle. The hydration of the slab may be contributing to the excess buoyancy of the subducting oceanic lithosphere, helping to drive flat-slab subduction.

  11. Independent tuning of double plasmonic waves in a free-standing graphene-spacer-grating-spacer-graphene hybrid slab.

    Science.gov (United States)

    Chen, Ying; Yao, Jin; Song, Zhengyong; Ye, Longfang; Cai, Guoxiong; Liu, Qing Huo

    2016-07-25

    The independent excitation and tuning of double plasmonic waves are realized in a free-standing graphene-spacer-grating-spacer-graphene (GSGSG) hybrid slab, which consists of two graphene field effect transistors placed back-to-back to each other. Resulted from the high transparency and the tight confinement of surface plasmonic mode for the graphene, double plasmonic waves can be independently excited by guided-mode resonances (GMRs). Theoretical and numerical investigations are performed in the mid-infrared band. Furthermore, the tuning of individual GMR resonant wavelengths with respect to the system parameters is studied. The results provide opportunities to engineer the proposed hybrid slab for wavelength selective and multiplexing applications.

  12. Nondestructive analysis of alkali-silica reaction damage in concrete slabs using shear waves

    Science.gov (United States)

    Khazanovich, Lev; Freeseman, Katelyn; Salles, Lucio; Clayton, Dwight

    2018-04-01

    Alkali-silica reaction (ASR) is the chemical reaction that occurs in concrete. It is caused by the interaction of alkalis in Portland cement and silica in aggregates and results in microcracks within the material. This type of damage has been the focus of nondestructive evaluation efforts in recent history, but no work was done on in-situ structures or large-scale samples. To address these limitations, an ultrasonic linear array device, MIRA, was utilized for this research. An experimental investigation was performed on four slabs with various levels of alkali-silica reaction at the Electric Power Research Institute (EPRI) [1]. One-period impulses with a target of 50kHz center frequency were selected in this study. We propose the use of the Hilbert Transform Indicator (HTI) for quantification of ASR damage [2]. A higher HTI value would be indicative of damaged concrete, while a low value represents sound concrete. In general, values below 90 are regarded as an indicator of sound concrete while values above 100 indicate the presence of damage [3]. The ability of the HTI values to distinguish between areas of damaged concrete was evident via the production of color intensity maps. The maps show that the control specimen, was in good condition, while other slabs exhibited higher levels of damage as indicated by the HTI values. It should be noted that extreme damage conditions were not present in any of the slabs. Evaluation of migration-based reconstructions can give a qualitative characterization of large scale or excessive subsurface damage. However, for detection of stochastic damage mechanisms such as freeze-thaw damage, evaluation of the individual time-history data can provide additional information. A comparison of the spatially diverse measurements on several concrete slabs with varying freeze-thaw damage levels is given in this study. Signal characterization scans of different levels of freeze-thaw damage at various transducer spacing is investigated. The

  13. Global P-wave tomography of mantle plumes and subducting slabs

    Science.gov (United States)

    Yamamoto, Y.; Zhao, D.

    2008-12-01

    There are many volcanoes on the Earth which can be generally classified into 3 categories: island arc volcanoes, mid-ocean ridge volcanoes, and hotspot volcanoes. Hotspot volcanoes denote intraplate volcanoes like Hawaii, or anomalously large mid-ocean ridge volcanoes like Iceland. So far many researchers have studied the origin of hotspot volcanoes and have used mantle plume hypothesis to explain them. However, we still have little knowledge about mantle plumes yet. In this study, we determined a new model of whole mantle P-wave tomography to understand the origin of hotspot volcanoes. We used the global tomography method of Zhao (2001, 2004). A 3-D grid net was set up in the mantle, and velocity perturbations at every grid nodes were taken as unknown parameters. The iasp91 velocity model (Kennett and Engdahl, 1991) was taken as the 1-D initial model. We selected 9106 earthquakes from the events occurred in the last forty years from the ISC catalog. About 1.6 million arrival-time data of five-type P phases (P, pP, PP, PcP, and Pdiff) were used to conduct the tomographic inversion. In our previous model (Zhao, 2004), the grid interval in the E-W direction is too small in the polar regions. In this study, in order to remedy this problem, we use a flexible-grid approach to make the lateral grid intervals in the polar regions nearly the same as the other portions of the mantle. As a result, the tomographic images in the polar regions are remarkably improved. Our new tomographic model shows huge low-velocity (low-V) zones in the entire mantle under Tahiti and Lake Victoria, which reflect the Pacific and African superplumes, being consistent with the previous studies. A clear low-V zone is revealed under Mt. Erebus volcano in Antarctica. Other major hotspots also exhibit significant low-V zones in the mantle under their surface locations. Beneath Bering Sea, we found that the Pacific slab is subducting from the Aleutian trench and it is stagnant in the mantle transition

  14. Single tunable laser interrogation of slab-coupled optical sensors through resonance tuning.

    Science.gov (United States)

    Chadderdon, Spencer; Woodard, Leeland; Perry, Daniel; Selfridge, Richard H; Schultz, Stephen M

    2013-04-20

    This paper describes a method for tuning the resonant wavelengths of slab-coupled optical fiber sensors (SCOSs). This method allows multiple sensors to be interrogated simultaneously with a single tunable laser. The resonances are tuned by rotating a biaxial slab waveguide relative to an optical D-fiber. As the slab waveguide rotates, its effective index of refraction changes causing the coupling wavelengths of the slab waveguide and D-fiber to shift. A SCOS fabricated with potassium titanyl phosphate crystal as the slab waveguide is shown to have resonance tuning ranges of 6.67 and 22.24 nm, respectively, for TM and TE polarized modes.

  15. Effect of rheological approximations on slab detachment in 3D numerical simulations of continental collision

    Science.gov (United States)

    Pusok, Adina E.; Kaus, Boris; Popov, Anton

    2017-04-01

    It is commonly accepted that slab detachment results from the development of extensional stresses within the subducting slab. Subduction slowdown due to arrival of buoyant continental material at the trench is considered to cause such stress build up in the slab. Following slab detachment, slab pull partially or completely loses its strength and hot asthenosphere may flow through the slab window, which can have major consequences for continental collision. The dynamics of slab detachment has been extensively studied in 2D (i.e. analytical and numerical), but 3D models of slab detachment during continental collision remain largely unexplored. Some of the previous 3D models have investigated the role of an asymmetric margin on the propagation of slab detachment (van Hunen and Allen, 2011), the impact of slab detachment on the curvature of orogenic belts (Capitanio and Replumaz, 2013), the role of the collision rate on slab detachment depth (Li et al., 2013) or the effect of along-trench variations on slab detachment (Duretz et al., 2014). However, rheology of mantle and lithosphere is known to have a major influence on the dynamics of subduction. Here, we explore a range of different rheological approximations to understand their sensitivity on the possible scenarios. We employ the code LaMEM (Kaus et al., 2016) to perform 3D simulations of subduction/continental collision in an integrated lithospheric and upper-mantle scale model. The models exhibit a wide range of behaviours depending on the rheological law employed: from linear, to temperature-dependent visco-elasto-plastic rheology that takes into account both diffusion and dislocation creep. For example, we find that slab dynamics varies drastically between end member models: in viscous approximations, slab detachment is slow, dominated by viscous thinning, while for a non-linear visco-elasto-plastic rheology, slab detachment is relatively fast, dominated by plastic breaking and inducing strong mantle flow in

  16. Improved Broadband Liner Optimization Applied to the Advanced Noise Control Fan

    Science.gov (United States)

    Nark, Douglas M.; Jones, Michael G.; Sutliff, Daniel L.; Ayle, Earl; Ichihashi, Fumitaka

    2014-01-01

    The broadband component of fan noise has grown in relevance with the utilization of increased bypass ratio and advanced fan designs. Thus, while the attenuation of fan tones remains paramount, the ability to simultaneously reduce broadband fan noise levels has become more desirable. This paper describes improvements to a previously established broadband acoustic liner optimization process using the Advanced Noise Control Fan rig as a demonstrator. Specifically, in-duct attenuation predictions with a statistical source model are used to obtain optimum impedance spectra over the conditions of interest. The predicted optimum impedance information is then used with acoustic liner modeling tools to design liners aimed at producing impedance spectra that most closely match the predicted optimum values. Design selection is based on an acceptance criterion that provides the ability to apply increased weighting to specific frequencies and/or operating conditions. Constant-depth, double-degree of freedom and variable-depth, multi-degree of freedom designs are carried through design, fabrication, and testing to validate the efficacy of the design process. Results illustrate the value of the design process in concurrently evaluating the relative costs/benefits of these liner designs. This study also provides an application for demonstrating the integrated use of duct acoustic propagation/radiation and liner modeling tools in the design and evaluation of novel broadband liner concepts for complex engine configurations.

  17. Detailed Structure and Thickness of Upper Mantle Discontinuities in the Tonga Subduction Zone From Regional Broadband Arrays

    Science.gov (United States)

    Tibi, R.; Wiens, D. A.

    2004-12-01

    Recordings of deep Tonga earthquakes from two arrays of 12 broadband seismographs each in the Fiji and Tonga islands are stacked and searched for reflections and conversions from upper mantle discontinuities in the Tonga subduction zone. The arrays operated as part of the Seismic Arrays in Fiji and Tonga (SAFT) experiment from July 2001 to August 2002. In comparison with the commonly used teleseismic approaches, the short path lengths for the regional data provide smaller Fresnel zones and high frequency content for precise mapping of discontinuity topography and sharpness. This is particularly important for a subduction zone, where variations in temperature and water content may be expected which should cause changes in the elevation and sharpness of the discontinuities. We studied the phases s410p, P660p and S660p. To enhance these low-amplitude phases, deconvolved seismograms from each event/array pair are aligned on the maximum amplitude of the direct P wave and subsequently slant-stacked. For the 410-km discontinuity, the results show no systematic variations in depth with distance to the cold slab. The 660-km discontinuity varies between 656 and 714 km in depth. For the southern and central parts of the subduction zone, the largest depths occur in the core of the Tonga slab. For the northern part, two separate depressions of the 660 are observed. These anomalies are interpreted as being induced by the active, steeply subducting Tonga deep zone and a subhorizontally lying remnant of subducted lithosphere from the fossil Vityaz trench, respectively. Interpreting the deflections of the 660 in terms of local temperatures implies a thermal anomaly at 660 km depth of -800 to -1200oK for the Tonga slab, and -600 to -950oK for the piece of the Vityaz lithosphere. Except for the southern region where it thickens, the Tonga slab seems to penetrate the 660 with little deformation. Waveform modeling susggests that both the 410 and 660 discontinuities are sharp. The 410

  18. Detailed structure and sharpness of upper mantle discontinuities in the Tonga subduction zone from regional broadband arrays

    Science.gov (United States)

    Tibi, Rigobert; Wiens, Douglas A.

    2005-06-01

    Recordings of deep Tonga earthquakes from two arrays of 12 broadband seismographs each in the Fiji and Tonga islands are stacked and searched for reflections and conversions from upper mantle discontinuities in the Tonga subduction zone. The arrays operated as part of the Seismic Arrays in Fiji and Tonga (SAFT) experiment from July 2001 to August 2002. In comparison with the commonly used teleseismic approaches, the short path lengths for the local data provide smaller Fresnel zones and high-frequency content for precise mapping of discontinuity topography and sharpness. To enhance the low-amplitude discontinuity phases s410p, P660p and S660p, deconvolved seismograms from each event/array pair are aligned on the maximum amplitude of the direct P wave and subsequently slant stacked. For the 410-km discontinuity, the results show no systematic variations in depth with distance to the cold slab. The 660-km discontinuity varies between 656 and 714 km in depth. For the southern and central parts of the subduction zone, the largest depths occur in the core of the Tonga slab. For the northern part, two separate depressions of the 660-km discontinuity are observed. These anomalies are interpreted as being induced by the active, steeply subducting Tonga deep zone and a subhorizontally lying remnant of subducted lithosphere from the fossil Vityaz trench, respectively. Interpreting the deflections of the 660-km discontinuity in terms of local temperatures implies a thermal anomaly of -800°K to -1200°K at 660 km depth. Except for the southern region where it may thicken, the width of the depressed 660-km discontinuity region implies that the Tonga slab seems to penetrate the 660-km discontinuity with little deformation. Waveform modeling suggests that both the 410- and 660-km discontinuities are sharp. The 660-km discontinuity is at most 2 km thick in many parts of the region, and a first-order discontinuity cannot be precluded. The 410-km discontinuity thickness shows

  19. Imaging the western Mediterranean using high-density broadband arrays (Invited)

    Science.gov (United States)

    Villasenor, A.

    2013-12-01

    The process or processes responsible for the formation and present-day structure of the western Mediterranean continue to be the subject of intense debate, with two major families of models being proposed: subduction-related processes (e.g. active subduction, slab rollback, slab tear, asymmetric delamination) and convective removal of the lithosphere. In order to better understand the geodynamic evolution of the region a number of temporary deployments of broadband seismometers have been carried out, starting in 2007 with project TOPO-IBERIA in Spain and continued with similar deployments in Morocco, Portugal and France. In total, more than 325 temporary and permanent stations have since been deployed, resulting in an average station spacing of approximately 50 km for most of the region. Traditional imaging methods greatly benefit from these dense seismic arrays. For example local earthquake tomography of the Gibraltar arc region using arrival time data from the temporary arrays dramatically improves the images with respect to using permanent networks alone. However, in order to fully exploit the unprecedented amount of information provided by these arrays, new seismic imaging methods are being developed. In addition to these new imaging methods, new quality control procedures that make use of the dense station spacing can be applied to the data in order to identify data errors (bad timing, component orientation and/or polarity, instrument response, seismometer malfunction, etc). Due to the amount of data, quality control is a time consuming task that should be as automated as possible, but results in a high quality dataset with fewer outliers, and therefore in better images. I will present new imaging results for the western Mediterranean that illustrate the improvement in traditional (local earthquake tomography, teleseismic tomography, receiver functions) and new modeling techniques (ambient noise tomography, full waveform inversion, joint gravity and dispersion

  20. Analysis of the Behaviour of Composite Steel and Steel Fiber Reinforced Concrete Slabs

    Directory of Open Access Journals (Sweden)

    Mindaugas Petkevičius

    2011-04-01

    Full Text Available There was a pending influence of steel fiber on the strength and stiffness of composite steel–concrete slabs under statical short–time load. Steel profiled sheeting and steel fiber reinforced concrete were used for specimens. Four composite slabs were made. Experimental investigations into the behaviour and influence of steel fiber reinforced concrete in composite slabs were conducted. Transverse, longitudinal, shear deformation and deflection of the slab were measured. The results indicated that the use of steel fiber in composite slabs was effective: strength was 20–24 % higher and the meanings of deflections under the action of the bending moment were 0,6MR (where MR is the bending moment at failure of the slabs and were 16–18 % lower for slabs with usual concrete. Article in Lithuanian

  1. Using Wireless Sensor Networks and Trains as Data Mules to Monitor Slab Track Infrastructures.

    Science.gov (United States)

    Cañete, Eduardo; Chen, Jaime; Díaz, Manuel; Llopis, Luis; Reyna, Ana; Rubio, Bartolomé

    2015-06-26

    Recently, slab track systems have arisen as a safer and more sustainable option for high speed railway infrastructures, compared to traditional ballasted tracks. Integrating Wireless Sensor Networks within these infrastructures can provide structural health related data that can be used to evaluate their degradation and to not only detect failures but also to predict them. The design of such systems has to deal with a scenario of large areas with inaccessible zones, where neither Internet coverage nor electricity supply is guaranteed. In this paper we propose a monitoring system for slab track systems that measures vibrations and displacements in the track. Collected data is transmitted to passing trains, which are used as data mules to upload the information to a remote control center. On arrival at the station, the data is stored in a database, which is queried by an application in order to detect and predict failures. In this paper, different communication architectures are designed and tested to select the most suitable system meeting such requirements as efficiency, low cost and data accuracy. In addition, to ensure communication between the sensing devices and the train, the communication system must take into account parameters such as train speed, antenna coverage, band and frequency.

  2. Using Wireless Sensor Networks and Trains as Data Mules to Monitor Slab Track Infrastructures

    Directory of Open Access Journals (Sweden)

    Eduardo Cañete

    2015-06-01

    Full Text Available Recently, slab track systems have arisen as a safer and more sustainable option for high speed railway infrastructures, compared to traditional ballasted tracks. Integrating Wireless Sensor Networks within these infrastructures can provide structural health related data that can be used to evaluate their degradation and to not only detect failures but also to predict them. The design of such systems has to deal with a scenario of large areas with inaccessible zones, where neither Internet coverage nor electricity supply is guaranteed. In this paper we propose a monitoring system for slab track systems that measures vibrations and displacements in the track. Collected data is transmitted to passing trains, which are used as data mules to upload the information to a remote control center. On arrival at the station, the data is stored in a database, which is queried by an application in order to detect and predict failures. In this paper, different communication architectures are designed and tested to select the most suitable system meeting such requirements as efficiency, low cost and data accuracy. In addition, to ensure communication between the sensing devices and the train, the communication system must take into account parameters such as train speed, antenna coverage, band and frequency.

  3. Multiplexed two-photon microscopy of dynamic biological samples with shaped broadband pulses.

    Science.gov (United States)

    Pillai, Rajesh S; Boudoux, Caroline; Labroille, Guillaume; Olivier, Nicolas; Veilleux, Israel; Farge, Emmanuel; Joffre, Manuel; Beaurepaire, Emmanuel

    2009-07-20

    Coherent control can be used to selectively enhance or cancel concurrent multiphoton processes, and has been suggested as a means to achieve nonlinear microscopy of multiple signals. Here we report multiplexed two-photon imaging in vivo with fast pixel rates and micrometer resolution. We control broadband laser pulses with a shaping scheme combining diffraction on an optically-addressed spatial light modulator and a scanning mirror allowing to switch between programmable shapes at kiloHertz rates. Using coherent control of the two-photon excited fluorescence, it was possible to perform selective microscopy of GFP and endogenous fluorescence in developing Drosophila embryos. This study establishes that broadband pulse shaping is a viable means for achieving multiplexed nonlinear imaging of biological tissues.

  4. Rail-based Broadband Synthetic Aperture Ocean Measurement System

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Enables collection of broadband acoustic scattering databases where acoustic sources and receivers can be translated on a precise linear path under program...

  5. Reconstructing subducted oceanic lithosphere by "reverse-engineering" slab geometries: The northern Philippine Sea Plate

    Science.gov (United States)

    Pownall, Jonathan M.; Lister, Gordon S.; Spakman, Wim

    2017-09-01

    Subducting slabs commonly acquire complex geometries from the migration of subduction trenches, slab-mantle interaction, slab tearing, and collision of slabs at depth. Although it is possible to construct three-dimensional models of subducted slabs using earthquake hypocenter locations and tomographic models, it is often not possible to rigorously test their accuracy. Here we present a methodology for performing such a test, by "reverse-engineering" the presubduction configuration of a slab of oceanic lithosphere from interpretations of its present-day morphology. We illustrate our approach for the Ryukyu and Shikoku slabs, northwest Philippine Sea, having simulated them as viscoelastic sheets that we unfolded and "floated" to the surface. The net strain distribution of the floated mesh indicated which parts of the original slab model were geometrically viable (minimal net strain) and which parts of the mesh required additional tears and/or zones of localized ductile extension to have enabled the slab to deform during subduction. In the instance of the Ryukyu and Shikoku slabs, the Palau-Kyushu and Gagua ridges are shown to have both acted as planes of weakness that broke into major vertical slab tears. These subducted ridges are connected by a trench-parallel tear that represented the former contact between the Huatung and West Philippine Basins. The fossil spreading center of the Shikoku Basin formed a separate slab window upon subduction along the Nankai Trough. The methodology presented herein is a powerful tool to evaluate complex slab morphologies, infer the locations of slab tears, and therefore reconstruct intricate configurations of subducted oceanic lithosphere.

  6. Flexural Behavior of Continuous Bubbled Reinforced Reactive Powder Concrete Flat Slab

    Directory of Open Access Journals (Sweden)

    Mohammad Redha K. Mahmood

    2017-05-01

    Full Text Available This paper presents an experimental investigation on flexural behavior of continuous bubbled reinforced Reactive Powder Concrete (RPC flat slabs. Bubbled slab is one of the various types of voided slabs. It consist of bubbles placed inside a concrete slab which will reduce the self-weight of the structure by about 35% (Tina Lai 2009. On the other hand, using RPC make it possible for structural member to have smaller dimensions due to the great strength of this type of concrete. In this study these two method are used to increase the building spaces dimensions by reducing self-weigh of the structure by using bubbled slabs and to decrease the structural members' dimensions by using RPC have been investigated together. To study the flexural behavior of continuous bubbled flat slabs such as the ultimate load carrying capacity, central deflection and slabs crack pattern at the ultimate load, seven types of slabs were tested. The parameters of the study were type of concrete (RPC and Normal Concrete (NC, bubbles diameter to slab thickness ratio (D/t of (0.6 and 0.7, type of loading (distributed and line load and solid slab. The test results show that the crack pattern and ultimate load capacity as well as maximum deflection depends on all of the mentioned parameters, were by increasing (D/t ratio the ultimate load capacity increases about (7.36%, 5.46% and 16.52% for RPC slabs under distributed load, line load and NC slabs, respectively. The solid slab increases the ultimate load about (4.05% compare to bubbled slab. Also, the line load decreases the ultimate load compare to distributed load by (3.45-5.16% for different (D/t ratio, and using the NC also decreases the ultimate load compare to RPC by (48-52.13% for different (D/t ratio

  7. Interface and material engineering for zigzag slab lasers.

    Science.gov (United States)

    Liu, Fei; Dong, Siyu; Zhang, Jinlong; Jiao, Hongfei; Ma, Bin; Wang, Zhanshan; Cheng, Xinbin

    2017-12-01

    Laser damage of zigzag slab lasers occurs at interface between laser crystal and SiO 2 film. Although an additional HfO 2 layer could be used to manipulate electric-field on the crystal-film interface, their high absorption and polycrystalline structure were unacceptable. SiO 2 was then doped in HfO 2 to suppress its crystallization and to achieve low absorption by annealing. Hf x Si 1-x O 2 nanocomposite layers were then inserted between laser crystal and SiO 2 film to minimize electric-field at crystal-film interface. Laser damage resistance of this new architecture is two times higher than that of traditional zigzag slab lasers.

  8. Oscillating Casimir force between two slabs in a Fermi sea

    DEFF Research Database (Denmark)

    Li-Wei, Chen; Guo-Zhen, Su; Jin-Can, Chen

    2012-01-01

    The Casimir effect for two parallel slabs immersed in an ideal Fermi sea is investigated at both zero and nonzero temperatures. It is found that the Casimir effect in a Fermi gas is distinctly different from that in an electromagnetic field or a massive Bose gas. In contrast to the familiar result...... that the Casimir force decreases monotonically with the increase of the separation L between two slabs in an electromagnetic field and a massive Bose gas, the Casimir force in a Fermi gas oscillates as a function of L. The Casimir force can be either attractive or repulsive, depending sensitively on the magnitude...... of L. In addition, it is found that the amplitude of the Casimir force in a Fermi gas decreases with the increase of the temperature, which also is contrary to the case in a Bose gas, since the bosonic Casimir force increases linearly with the increase of the temperature in the region T

  9. Minimization of heat slab nodes with higher order boundary conditions

    International Nuclear Information System (INIS)

    Solbrig, C.W.

    1992-01-01

    The accuracy of a numerical solution can be limited by the numerical approximation to the boundary conditions rather than the accuracy of the equations which describe the interior. The study presented in this paper compares the results from two different numerical formulations of the convective boundary condition on the face of a heat transfer slab. The standard representation of the boundary condition in a test problem yielded an unacceptable error even when the heat transfer slab was partitioned into over 300 nodes. A higher order boundary condition representation was obtained by using a second order approximation for the first derivative at the boundary and combining it with the general equation used for inner nodes. This latter formulation produced reasonable results when as few as ten nodes were used

  10. Radon Sub-slab Suctioning System Integrated in Insulating Layer

    DEFF Research Database (Denmark)

    Rasmussen, Torben Valdbjørn

    2013-01-01

    of prefabricated lightweight elements were introduced and demonstrated. The principle was demonstrated on a concrete ground slab floor with a concrete slab on top of a thermal insulation layer above a capillary-breaking layer mounted on stable ground. The thermal insulation and the capillary-breaking layer......A new principle for radon protection, using a system containing a horizontal grid of air ducts pressurised within the rigid insulation material, was presented. The principle was based on the principles for pressure reduction of the zone underneath the ground floor construction. A new element...... consisted of a rigid insulation material. The new solution integrates the capillary-breaking layer and a pressure reduction zone,denoted the radon–suctioning layer, in one element. The new solution introduces the radonsuctioning layer as a horizontal grid of air ducts with low pressure to catch air...

  11. Watertightness in anti-flotation slabs: MIS-RJ case

    Directory of Open Access Journals (Sweden)

    C. Britez

    Full Text Available It is common in coastal cities as Rio de Janeiro, that buildings located close to the shoreline have their basements below water table level. In most cases, the engineering solution for these buildings is to design a massive anti-flotation slab to satisfy, principally, the issues related to structural dimensioning and calculation hypothesis. On the other hand, the execution of this solution imply in significant construction problems related to reinforced concrete watertightness and durability. This paper presents a case study about challenges and solutions devised to execute an anti-flotation, 1m thick, 1200m³ reinforced concrete slab for the new Museu de Imagem e Som (MIS - Sound and Image Museum, located at 50m from the seashore, at Copacabana in Rio de Janeiro, RJ. The results show that concrete proportions, concreting plan and pouring method adopted were decisive in obtaining a watertight structure, avoiding thus the employment of traditional waterproofing alternatives.

  12. Anticrack nucleation as triggering mechanism for snow slab avalanches.

    Science.gov (United States)

    Heierli, J; Gumbsch, P; Zaiser, M

    2008-07-11

    Snow slab avalanches are believed to begin by the gravity-driven shear failure of weak layers in stratified snow. The critical crack length for shear crack propagation along such layers should increase without bound as the slope decreases. However, recent experiments show that the critical length of artificially introduced cracks remains constant or, if anything, slightly decreases with decreasing slope. This surprising observation can be understood in terms of volumetric collapse of the weak layer during failure, resulting in the formation and propagation of mixed-mode anticracks, which are driven simultaneously by slope-parallel and slope-normal components of gravity. Such fractures may propagate even if crack-face friction impedes downhill sliding of the snowpack, indicating a scenario in which two separate conditions have to be met for slab avalanche release.

  13. Bolometric detection of ferromagnetic resonance in YIG slab

    Science.gov (United States)

    Tu, Sa; Białek, Marcin; Zhang, Youguang; Zhao, Weisheng; Yu, Haiming; Ansermet, Jean-Philippe

    2017-10-01

    The resistance of the Pt bar deposited on the YIG slab was monitored while the magnetic field was ramped through the ferromagnetic resonance with the YIG slab facing a coplanar waveguide resonator excited at 4.3 GHz excitation. The resistance change provides detection of the ferromagnetic resonance with a high signal-to-noise ratio. It is ascribed to a change in the temperature of the Pt bars. The thermal origin of the signal is confirmed by the observation that the signal vanishes when field modulation is applied at frequencies above 6 Hz. The spin pumping effect was vanishingly small, and the anisotropic magnetoresistance of the Pt bar, though quite easily observed, would imply a rectification voltage that is much smaller than the bolometric effect.

  14. Slab detachment under the Eastern Alps seen by seismic anisotropy.

    Science.gov (United States)

    Qorbani, Ehsan; Bianchi, Irene; Bokelmann, Götz

    2015-01-01

    We analyze seismic anisotropy for the Eastern Alpine region by inspecting shear-wave splitting from SKS and SKKS phases. The Eastern Alpine region is characterized by a breakdown of the clear mountain-chain-parallel fast orientation pattern that has been previously documented for the Western Alps and for the western part of the Eastern Alps. The main interest of this paper is a more detailed analysis of the anisotropic character of the Eastern Alps, and the transition to the Carpathian-Pannonian region. SK(K)S splitting measurements reveal a rather remarkable lateral change in the anisotropy pattern from the west to the east of the Eastern Alps with a transition area at about 12°E. We also model the backazimuthal variation of the measurements by a vertical change of anisotropy. We find that the eastern part of the study area is characterized by the presence of two layers of anisotropy, where the deeper layer has characteristics similar to those of the Central Alps, in particular SW-NE fast orientations of anisotropic axes. We attribute the deeper layer to a detached slab from the European plate. Comparison with tomographic studies of the area indicates that the detached slab might possibly connect with the lithosphere that is still in place to the west of our study area, and may also connect with the slab graveyard to the East, at the depth of the upper mantle transition zone. On the other hand, the upper layer has NW-SE fast orientations coinciding with a low-velocity layer which is found above a more-or-less eastward dipping high-velocity body. The anisotropy of the upper layer shows large-scale NW-SE fast orientation, which is consistent with the presence of asthenospheric flow above the detached slab foundering into the deeper mantle.

  15. Concrete mixtures with high-workability for ballastless slab tracks

    OpenAIRE

    Olga Smirnova

    2017-01-01

    The concrete track-supporting layer and the monolithic concrete slab of ballastless track systems are made in-situ. For this reason the concrete mixtures of high workability should be used. Influence of the sand kind, the quartz microfiller fineness and quantity as well as quantity of superplasticizer on workability of fresh concrete and durability of hardened concrete is shown. The compositions of the high-workability concrete mixtures with lower consumption of superplasticizer are developed...

  16. Slab track systems for high-speed railways.

    OpenAIRE

    Michas, Georgios

    2012-01-01

    In the last 40 years an increase in train speed and axle load around the world and other challenges in the conventional ballasted track system gave birth to ballastless railway track system. This study examines in depth the various slab track systems that are being used today. Their design characteristics as well as the various requirements for efficient use are thoroughly explained. At least 34 different ballastless systems have been recorded in many railway networks throughout the world. Th...

  17. Brueckner G matrix for a planar slab of nuclear matter

    International Nuclear Information System (INIS)

    Baldo, M.; Lombardo, U.; Saperstein, E.E.; Zverev, M.V.

    2001-01-01

    The equation for the Brueckner G matrix is investigated for planar-slab geometry. A method for calculating the G matrix for a planar slab of nuclear matter is developed for a separable form of NN interaction. Actually, the separable version of the Paris NN potential is used. The singlet 1 S 0 and the triplet 3 S 1 - 3 D 1 channel are considered. The present analysis relies on the mixed momentum-coordinate representation, where use is made of the momentum representation in the slab plane and of the coordinate representation in the orthogonal direction. The full two-particle Hilbert space is broken down into the model subspace, where the two-particle propagator is considered exactly, and the complementary subspace, where the local-potential approximation is used, which was proposed previously for calculating the effective pairing potential. Specific calculations are performed for the case where the model subspace is constructed on the basis of negative-energy single-particle states. The G matrix is parametrically dependent on the total two-particle energy E and the total momentum P perpendicular in the slab plane. Since the G matrix is assumed to be further used to calculate the Landau-Migdal amplitude, the total two-particle energy is fixed at the value E = 2μ, where μ is the chemical potential of the system under investigation. The calculations are performed predominantly for P perpendicular = 0. The role of nonzero values of P perpendicular is assessed. The resulting G matrix is found to depend greatly on μ in the surface region

  18. Analytical approximation formulae for hydrogen diffusion in a metal slab

    International Nuclear Information System (INIS)

    Pohl, F.; Bohdansky, J.

    1984-12-01

    This report treats hydrogen diffusion in the first wall of a fusion machine (INTOR, reactor, etc.), taking the thermal load into account. Analytical approximation formulae are given for the concentration and flux density of hydrogen diffusing through a plane metal slab. The re-emission flux, particularly during the dwell time(s) of machine operation, is also described with analytical formulae. The analytical formulae are compared with numerical calculations for steel as first wall material. (orig.)

  19. Oscillation modes and transmission into a Fibonacci slab

    Science.gov (United States)

    Castro-Arce, Lamberto; Molinar-Tabares, Martin; Campos-Garcia, Julio; Figueroa-Navarro, Carlos; Isasi-Siqueiros, Leonardo; Manzanares-Martinez, Betsabe

    In our contribution we developed a study on the behavior of the transmission modes and a Pt / Zn slab of a Fibonacci array of longitudinal and transverse acoustic waves. We have worked with arrangements from n = 1 to10 and has managed to find the energy bands and transmission, filling factor 0.4 observing the appearance of Pseudo-Gaps in the evolution of the study when the arrangement Fibonacci increases. We acknowledge the support of SNI CONACYT.

  20. Broadband Planar 5:1 Impedence Transformer

    Science.gov (United States)

    Ehsan, Negar; Hsieh, Wen-Ting; Moseley, Samuel H.; Wollack, Edward J.

    2015-01-01

    This paper presents a broadband Guanella-type planar impedance transformer that transforms so 50 omega to 10 omega with a 10 dB bandwidth of 1-14GHz. The transformer is designed on a flexible 50 micrometer thick polyimide substrate in microstrip and parallel-plate transmission line topologies, and is Inspired by the traditional 4:1 Guanella transformer. Back-to-back transformers were designed and fabricated for characterization in a 50 omega system. Simulated and measured results are in excellent agreement.

  1. Optimizing UV Index determination from broadband irradiances

    Science.gov (United States)

    Tereszchuk, Keith A.; Rochon, Yves J.; McLinden, Chris A.; Vaillancourt, Paul A.

    2018-03-01

    A study was undertaken to improve upon the prognosticative capability of Environment and Climate Change Canada's (ECCC) UV Index forecast model. An aspect of that work, and the topic of this communication, was to investigate the use of the four UV broadband surface irradiance fields generated by ECCC's Global Environmental Multiscale (GEM) numerical prediction model to determine the UV Index. The basis of the investigation involves the creation of a suite of routines which employ high-spectral-resolution radiative transfer code developed to calculate UV Index fields from GEM forecasts. These routines employ a modified version of the Cloud-J v7.4 radiative transfer model, which integrates GEM output to produce high-spectral-resolution surface irradiance fields. The output generated using the high-resolution radiative transfer code served to verify and calibrate GEM broadband surface irradiances under clear-sky conditions and their use in providing the UV Index. A subsequent comparison of irradiances and UV Index under cloudy conditions was also performed. Linear correlation agreement of surface irradiances from the two models for each of the two higher UV bands covering 310.70-330.0 and 330.03-400.00 nm is typically greater than 95 % for clear-sky conditions with associated root-mean-square relative errors of 6.4 and 4.0 %. However, underestimations of clear-sky GEM irradiances were found on the order of ˜ 30-50 % for the 294.12-310.70 nm band and by a factor of ˜ 30 for the 280.11-294.12 nm band. This underestimation can be significant for UV Index determination but would not impact weather forecasting. Corresponding empirical adjustments were applied to the broadband irradiances now giving a correlation coefficient of unity. From these, a least-squares fitting was derived for the calculation of the UV Index. The resultant differences in UV indices from the high-spectral-resolution irradiances and the resultant GEM broadband irradiances are typically within 0

  2. Chemical recognition with broadband THz spectroscopy

    DEFF Research Database (Denmark)

    Fischer, Bernd M.; Helm, Hanspeter; Jepsen, Peter Uhd

    2004-01-01

    contains unique fingerprints of a very large number of crystalline materials, including explosives, illicit drugs as well as most other chemicals in powder form. Since many packaging materials are transparent to THz radiation this fundamental property of crystalline compounds allows remote (contact...... with broadband THz spectroscopy. Amorphous systems of great biotechnical importance include DNA and proteins, both in aqueous solution and as dried matter. We will discuss methods for THz science and technology to attack the very complex problems involved in the extraction of useful new information which may...

  3. Constraints on the Geometry of the Farallon Slab from the Joint Interpretation of All Available Imaging Results from the Earthscope USArray Deployment in the Lower 48 States

    Science.gov (United States)

    Esker, A.; Pavlis, G. L.

    2017-12-01

    We assembled all available seismic tomography models distributed through the IRIS DMC and other sources. We combined these images with our own results using 3D plane wave migration of P to S conversion data derived from the USArray data set and other broadband seismic stations in the lower 48 states. All the tomography models were converted into SEGY format and interpolated onto a regular grid in a UTM reference frame. That innovation makes joint interpretation feasible using a seismic interpretation software (Petrel) because we treat both the tomography models and scattered wave image results as if they were 3D seismic reflection data. The careful designed interface of a modern exploration package makes exploring a range of interpretation packages much faster and allowed us to produce a more comprehensive interpretation of all available data. The tomography models are nearly an order of magnitude smoother than the scattered wave images, so we use the tomography models as a cross-validation in interpretation unless the scattered wave images are ambiguous. The focus of this study is testing a conjecture in an earlier paper (Pavlis, 2011) for the presence of a single continuous horizon interpreted as the top of the Farallon Slab. As in the previous paper we constrained the western edge of this surface with the location of Cascadia trench as well as a virtual edge from a back projection of the Mendocino triple junction using Pacific-North America motion over the past 30 Ma. We also simulated crustal multiple effects on the plane wave migration results using crustal geometry estimates produced by the Earthscope Automated Receiver Survey (EARS). This confirmed the scattered wave images were not reliable in the upper mantle at depths shallower than 200 km due to contamination by crustal multiples. Most tomography models show a steep dip in the slab immediately east of the volcanic arc and our surface follows the average geometry defined by a visual comparison of all the

  4. High Performance Slab-on-Grade Foundation Insulation Retrofits

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, Louise F. [NorthernSTAR, St. Paul, MN (United States); Mosiman, Garrett E. [NorthernSTAR, St. Paul, MN (United States)

    2015-09-01

    ?A more accurate assessment of SOG foundation insulation energy savings than traditionally possible is now feasible. This has been enabled by advances in whole building energy simulation with 3-dimensional foundation modelling integration at each time step together with an experimental measurement of the site energy savings of SOG foundation insulation. Ten SOG insulation strategies were evaluated on a test building to identify an optimum retrofit insulation strategy in a zone 6 climate (Minneapolis, MN). The optimum insulation strategy in terms of energy savings and cost effectiveness consisted of two components: (a) R-20 XPS insulation above grade, and, (b) R-20 insulation at grade (comprising an outer layer of R-10 insulation and an interior layer of R-12 poured polyurethane insulation) tapering to R-10 XPS insulation at half the below-grade wall height (the lower half of the stem wall was uninsulated). The optimum insulation strategy was applied to single and multi-family residential buildings in climate zone 4 - 7. The highest site energy savings of 5% was realized for a single family home in Duluth, MN, and the lowest savings of 1.4 % for a 4-unit townhouse in Richmond, VA. SOG foundation insulation retrofit simple paybacks ranged from 18 to 47 years. There are other benefits of SOG foundation insulation resulting from the increase in the slab surface temperatures. These include increased occupant thermal comfort, and a decrease in slab surface condensation particularly around the slab perimeter.

  5. Surface waves in the partially ionized solar plasma slab

    Science.gov (United States)

    Pandey, B. P.

    2013-12-01

    The properties of surface waves in the partially ionized, incompressible magnetized plasma slab are investigated in the present work. The waves are affected by the non-ideal magnetohydrodynamic (MHD) effects which cause the finite drift of the magnetic field in the medium. When the finite drift of the magnetic field is ignored, the characteristics of the wave propagation in the partially ionized plasma fluid are similar to the ideal MHD, except now the propagation properties depend on the fractional ionization of the medium. In the presence of the Hall diffusion, the propagation of the sausage and kink surface waves depends on the level of fractional ionization of the medium. For example, short wavelength surface modes cannot propagate in the medium if the scale over which Hall operates is comparable to the size of the plasma slab. With the increasing ionization, the surface modes of shorter wavelength are permitted in the system. When both the Hall and Pedersen diffusion are present in the medium, the waves undergo damping. In the case of Pedersen dominating Hall, the damping of the long wavelength fluctuations is dependent on the ratio of the plasma densities inside and outside the slab and on the square of the Pedersen diffusivity. For typical solar parameters, waves may damp over few minutes.

  6. From stripe to slab confinement for DNA linearization in nanochannels

    Science.gov (United States)

    Cifra, Peter; Benkova, Zuzana; Namer, Pavol

    We investigate suggested advantageous analysis in the linearization experiments with macromolecules confined in a stripe-like channel using Monte Carlo simulations. The enhanced chain extension in a stripe that is due to significant excluded volume interactions between monomers in two dimensions weakens on transition to experimentally feasible slit-like channel. Based on the chain extension-confinement strength dependence and the structure factor behavior for the chain in stripe we infer the excluded volume regime typical for two-dimensional systems. On transition to the slab geometry, the advantageous chain extension decreases and the Gaussian regime is observed for not very long semiflexible chains. The evidence for pseudo-ideality in confined chains is based on indicators such as the extension curves, variation of the extension with the persistence length or the structure factor. The slab behavior is observed when the stripe (originally of monomer thickness) reaches the thickness larger than cca 10nm in the third dimension. This maximum height of the slab to retain the advantage of the stripe is very low and this have implication for DNA linearization experiments. The presented analysis, however, has a broader relevance for confined polymers. Support from Slovak R&D Agency (SRDA-0451-11) is acknowledged.

  7. Reducing Railway Noise with Porous Sound-Absorbing Concrete Slabs

    Directory of Open Access Journals (Sweden)

    Caiyou Zhao

    2014-01-01

    Full Text Available The effect of porous sound-absorbing concrete slabs on railway noise reduction is examined in this paper. First, the acoustical absorption coefficients of porous concrete materials with various aggregate types, gradations, fibre contents, and compaction indexes are measured in the laboratory. The laboratory results show that porous concrete that uses a composite of expanded perlite and slag as aggregate can not only obtain good acoustical absorption properties but also satisfy mechanical requirements. Also, the gradation of the combined aggregate has a significant effect on the acoustic absorption performance of the porous concrete, with an optimal aggregate gradation of 1~3 mm. Furthermore, the fibre content and compaction index affect both the strength and the acoustic absorption property of the porous concrete, with the optimum value of 0.3% and 1.6, respectively. Then, the findings from the laboratory studies are used to make porous sound-absorbing concrete slabs, which are applied in a test section. The measurements indicate that porous sound-absorbing concrete slabs can significantly reduce railway noise at different train speeds and that the amount of the noise reduction changes roughly linearly with speed when the train is traveling at less than 200 km/h. The maximum noise reduction is 4.05 dB at a speed of 200 km/h.

  8. The Green's function method for critical heterogeneous slabs

    International Nuclear Information System (INIS)

    Kornreich, D.E.

    1996-01-01

    Recently, the Green's Function Method (GFM) has been employed to obtain benchmark-quality results for nuclear engineering and radiative transfer calculations. This was possible because of fast and accurate calculations of the Green's function and the associated Fourier and Laplace transform inversions. Calculations have been provided in one-dimensional slab geometries for both homogeneous and heterogeneous media. A heterogeneous medium is analyzed as a series of homogeneous slabs, and Placzek's lemma is used to extend each slab to infinity. This allows use of the infinite medium Green's function (the anisotropic plane source in an infinite homogeneous medium) in the solution. To this point, a drawback of the GFM has been the limitation to media with c 1; however, mathematical solutions exist which result in oscillating Green's functions. Such calculations are briefly discussing. The limitation to media with c < 1 has been relaxed so that the Green's function may also be calculated for media with c ≥ 1. Thus, materials that contain fissionable isotopes may be modeled

  9. Calibrating a large slab vessel: A battle of the bulge

    International Nuclear Information System (INIS)

    Thomas, I.R.

    1993-01-01

    Slab tanks (critically-safe-by-geometry vessels) were proposed for the storage of concentrated, highly-enriched uranium solution in the design of the Fuel Processing Restoration (FPR) Facility at the Idaho Chemical Processing Plant (ICPP). Currently, measurements of bulk mass in ICPP annular vessels have standard deviations on the order of 0.2%, or less. ICPP personnel felt that their inexperience with the aforementioned expansions would prevent them from attaining comparable precision with slab tanks. To help assess the measurement accuracy of slab vessels, a full-scale mockup of those proposed for the FPR Facility was installed for test calibrations. These calibrations were designed to detect vessel expansion under differing conditions. This paper will compare the base-line, water calibrations with those of the higher-density aluminum nitrate, and any observed deflection will be described using vessel calibration techniques. The calibration using water at an elevated temperature was not performed due to the difficulty of maintaining the elevated temperature. This calibration probably will not be conducted because the construction of the FPR Facility has been halted

  10. Peramalan Pengguna Broadband di Indonesia [Forecasting of Broadband Users in Indonesia

    Directory of Open Access Journals (Sweden)

    Azwar Aziz

    2016-07-01

    Full Text Available Negara Indonesia memiliki peluang yang sangat besar untuk merealisasikan potensi pitalebar, mengingat Indonesia memiliki jumlah penduduk 253 juta orang dan pengguna internet 88,1 juta orang pada tahun 2014. Di sisi lain sektor komunikasi (salah satunya termasuk telekomunikasi merupakan satu-satunya sektor yang secara konsisten memberikan kontribusi pertumbuhan terhadap Pendapatan Domestik Bruto (PDB sebesar dua angka (double digit. Kemudian peran penting pemerintah adalah selalu mengantisipasi dalam membuat regulasi telekomunikasi, salah satu nya untuk mempercepat penggelaran prasarana pitalebar, seperti menerbitkan Peraturan Presiden RI. Nomor 96 Tahun 2014 tentang Rencana Pitalebar Indonesia 2014 – 2019.  Secara riil pembangunan jaringan pitalebar di Indonesia masih dilakukan di kota-kota besar, mengingat pengguna telekomunikasi sebagian besar berada di kota-kota besar. Selain itu perangkat hanset atau handphone, ketersediaan di pasaran masih terbatas dan harganya masih mahal. Kajian ini menggunakan metodologi penelitian kuantitatif dengan menghitung peramalan dan kualitatif, dengan melakukan observasi atau pengamatan langsung ke lapangan kepada perusahaan Telkom, Telkomsel, XL Axiata dan Indosat. Selanjutnya hasil penelitian ini diperoleh lima faktor yang mempengaruhi penggunaan pitalebar yaitu jumlah penduduk, produk domestik bruto, pendapatan per kapita, laju pertumbuhan ekonomi dan inflasi, dan laju penetrasi. Selain itu, hasil pitalebar menunjukkan pengguna pitalebar lima tahun kedepan selalu meningkat.*****Indonesia has a tremendous opportunity to implement the potential of broadband, as Indonesia has a population of 253 million people and 88.1 million Internet users in 2014. On the other hand, the communication sector (one of them including telecommunications is the only sector that is consistently contributed to the growth of Gross Domestic Product (GDP as many as two numbers (double-digit. Then the important role of government is

  11. Gd(5)Si(4-x)Bi(x) structures: novel slab sequences achieved by turning off the directionality of nearest-slab interactions.

    Science.gov (United States)

    Svitlyk, Volodymyr; Campbell, Branton J; Mozharivskyj, Yurij

    2009-11-02

    Substitution of Bi for Si leads to the complete cleavage of the interslab dimers T-T in the Gd(5)Si(4-x)Bi(x) system with x = 1.58 - 2.42 (T is a mixture of Si and Bi). Equivalence of the interslab T...T contacts, achieved through combination of the electronic and geometrical parameters, removes directionality of nearest-slab interactions and allows for a novel slab stacking. Two new slab sequences, ABCDABCD (x = 2.07, I4(1)/acd space group) and ABADABAD (x = 2.42, P4(2)bc), have been discovered in Gd(5)Si(4-x)Bi(x) in addition to the known one, ABAB, that is dominant among the RE(5)X(4) phases (RE is a rare-earth element, X is a p-element). The slab stacking for x = 2.07 and x = 2.42 is dictated by the second-nearest slab interactions which promote an origin shift either for the entire slab sequence as in ABCDABCD or for every other second-nearest slab pair as in ABADABAD. The loss of the directionality of the nearest-slab bonding allows for extensive stacking faults and leads to diffuse scattering.

  12. Evolution of the slab bending radius and the bending dissipation in three-dimensional subduction models with a variable slab to upper mantle viscosity ratio

    NARCIS (Netherlands)

    Schellart, W. P.

    2009-01-01

    Three-dimensional laboratory subduction models are presented investigating the influence of the slab/upper mantle viscosity ratio (ηSP/ηUM) on the slab bending radius (RB), with ηSP/ηUM = 66-1375. Here, RB is non-dimensionalized by dividing it by the upper mantle thickness (TUM). The results show

  13. Tomography of the subducting Pacific slab and the 2015 Bonin deepest earthquake (Mw 7.9).

    Science.gov (United States)

    Zhao, Dapeng; Fujisawa, Moeto; Toyokuni, Genti

    2017-03-15

    On 30 May 2015 an isolated deep earthquake (~670 km, Mw 7.9) occurred to the west of the Bonin Islands. To clarify its causal mechanism and its relationship to the subducting Pacific slab, we determined a detailed P-wave tomography of the deep earthquake source zone using a large number of arrival-time data. Our results show that this large deep event occurred within the subducting Pacific slab which is penetrating into the lower mantle. In the Izu-Bonin region, the Pacific slab is split at ~28° north latitude, i.e., slightly north of the 2015 deep event hypocenter. In the north the slab becomes stagnant in the mantle transition zone, whereas in the south the slab is directly penetrating into the lower mantle. This deep earthquake was caused by joint effects of several factors, including the Pacific slab's fast deep subduction, slab tearing, slab thermal variation, stress changes and phase transformations in the slab, and complex interactions between the slab and the ambient mantle.

  14. Post-Tensioned Concrete Long-Span Slabs in Projects of Modern Building Construction

    Science.gov (United States)

    Szydlowski, Rafal; Labuzek, Barbara

    2017-10-01

    Nowadays, design of modern an architectural building structures requires the use of slender and free from numerous supports slabs. The most suitable solution for above requirements are the post-tensioned slabs with unbounded tendons. Slabs prestressed by unbounded tendons are successfully used worldwide for several decades. During that time many recommendations dealing with the forming of geometry and prestressing, dimensioning and erection technology were issued. During the recent years prestressed slabs characterized by span and slenderness substantially exceeding recommended limitations were designed and erected with success in Poland. During the slabs erection and in two years of their using, the deflection of three oversized slabs were monitoring. In spite of designed the slabs significantly larger and slenderer than the recommended maximum value of span and span to depth ratio, the deflection of the slabs is definitely far from the limit value. The paper shows the geometry, characteristic and deflection of erected slabs and conclusion. Description of a very large span slab (21.3m), that was designed regarded to the information obtained from the previous realisation, is presented in this paper.

  15. Design of energy efficient building with radiant slab cooling

    Science.gov (United States)

    Tian, Zhen

    2007-12-01

    Air-conditioning comprises a substantial fraction of commercial building energy use because of compressor-driven refrigeration and fan-driven air circulation. Core regions of large buildings require year-round cooling due to heat gains from people, lights and equipment. Negative environmental impacts include CO2 emissions from electric generation and leakage of ozone-depleting refrigerants. Some argue that radiant cooling simultaneously improves building efficiency and occupant thermal comfort, and that current thermal comfort models fail to reflect occupant experience with radiant thermal control systems. There is little field evidence to test these claims. The University of Calgary's Information and Communications Technology (ICT) Building, is a pioneering radiant slab cooling installation in North America. Thermal comfort and energy performance were evaluated. Measurements included: (1) heating and cooling energy use, (2) electrical energy use for lighting and equipment, and (3) indoor temperatures. Accuracy of a whole building energy simulation model was evaluated with these data. Simulation was then used to compare the radiant slab design with a conventional (variable air volume) system. The radiant system energy performance was found to be poorer mainly due to: (1) simultaneous cooling by the slab and heating by other systems, (2) omission of low-exergy (e.g., groundwater) cooling possible with the high cooling water temperatures possible with radiant slabs and (3) excessive solar gain and conductive heat loss due to the wall and fenestration design. Occupant thermal comfort was evaluated through questionnaires and concurrent measurement of workstation comfort parameters. Analysis of 116 sets of data from 82 occupants showed that occupant assessment was consistent with estimates based on current thermal comfort models. The main thermal comfort improvements were reductions in (1) local discomfort from draft and (2) vertical air temperature stratification. The

  16. Improving Broadband Displacement Detection with Quantum Correlations

    Science.gov (United States)

    Kampel, N. S.; Peterson, R. W.; Fischer, R.; Yu, P.-L.; Cicak, K.; Simmonds, R. W.; Lehnert, K. W.; Regal, C. A.

    2017-04-01

    Interferometers enable ultrasensitive measurement in a wide array of applications from gravitational wave searches to force microscopes. The role of quantum mechanics in the metrological limits of interferometers has a rich history, and a large number of techniques to surpass conventional limits have been proposed. In a typical measurement configuration, the trade-off between the probe's shot noise (imprecision) and its quantum backaction results in what is known as the standard quantum limit (SQL). In this work, we investigate how quantum correlations accessed by modifying the readout of the interferometer can access physics beyond the SQL and improve displacement sensitivity. Specifically, we use an optical cavity to probe the motion of a silicon nitride membrane off mechanical resonance, as one would do in a broadband displacement or force measurement, and observe sensitivity better than the SQL dictates for our quantum efficiency. Our measurement illustrates the core idea behind a technique known as variational readout, in which the optical readout quadrature is changed as a function of frequency to improve broadband displacement detection. And, more generally, our result is a salient example of how correlations can aid sensing in the presence of backaction.

  17. Broadband impedance of the NESTOR storage ring

    International Nuclear Information System (INIS)

    Androsov, V.P.; Gladkikh, P.I.; Gvozd, A.M.; Karnaukhov, I.M.; Telegin, Yu.N.

    2011-01-01

    The contributions from lossy and inductive vacuum chamber components to the broadband impedance of the NESTOR storage ring are obtained by using both low-frequency analytical approaches and computer simulations. As was expected considering the small ring circumference (15.44m), the main contributions both to the longitudinal impedance Z || /n and the loss factor k loss come from the RF-cavity. Cavity impedance was also estimated with CST Microwave Studio (CST Studio Suite TM 2006) by simulating coaxial wire method commonly used for impedance measurements. Both estimates agree well. Finally, we performed the simulations of a number of inductive elements with CST Particle Studio 2010 by using wake field solver. We have also evaluated the bunch length in NESTOR taking the conservative estimate of 3 Ohm for the ring broadband impedance and have found that the bunch length s z = 0.5 cm could be obtained in steady state operation mode for the designed bunch current of 10 mA and RF-voltage of 250 kV.

  18. Reflective afocal broadband adaptive optics scanning ophthalmoscope

    Science.gov (United States)

    Dubra, Alfredo; Sulai, Yusufu

    2011-01-01

    A broadband adaptive optics scanning ophthalmoscope (BAOSO) consisting of four afocal telescopes, formed by pairs of off-axis spherical mirrors in a non-planar arrangement, is presented. The non-planar folding of the telescopes is used to simultaneously reduce pupil and image plane astigmatism. The former improves the adaptive optics performance by reducing the root-mean-square (RMS) of the wavefront and the beam wandering due to optical scanning. The latter provides diffraction limited performance over a 3 diopter (D) vergence range. This vergence range allows for the use of any broadband light source(s) in the 450-850 nm wavelength range to simultaneously image any combination of retinal layers. Imaging modalities that could benefit from such a large vergence range are optical coherence tomography (OCT), multi- and hyper-spectral imaging, single- and multi-photon fluorescence. The benefits of the non-planar telescopes in the BAOSO are illustrated by resolving the human foveal photoreceptor mosaic in reflectance using two different superluminescent diodes with 680 and 796 nm peak wavelengths, reaching the eye with a vergence of 0.76 D relative to each other. PMID:21698035

  19. A Design of Double Broadband MIMO Antenna

    Directory of Open Access Journals (Sweden)

    Yanfeng Geng

    2015-01-01

    Full Text Available The MIMO antenna applied to LTE mobile system should be miniaturization and can work in the current communication frequency band; isolation between each antenna unit also should be good so as to reduce loss of radio wave energy and improve the antenna performance of the MIMO system. This paper puts forward the design scheme of a broadband MIMO double antenna. And the design of antenna unit and debugging and related technical measures, such as bending antenna bracket, are both presented; the integration design of high isolation of ultra broadband MIMO antenna is realized on the plate with the volume of 100 × 52 × 0.8 mm3; antenna working bands are 698 MHz~960 MHz and 1710 MHz~2700 MHz; in the whole spectrum, the 10 dB of port isolation can be basically achieved; in low frequency band, the isolation degree of antenna port can reach 12 dB.

  20. Reliability monitoring of broadband access networks

    Directory of Open Access Journals (Sweden)

    Perlicki Krzysztof

    2017-06-01

    Full Text Available One of the critical issues for broadband accesss is how to test the access network infrastructure and quality of optical signal. The installation and powering up of an optical fiber access networks requires measurement techniques for verifying the link has been configured properly and that its constituent components are functioning correctly. Maintenance functions for a broadband optical access network are classified in two main categories: preventive maintenance and post-fault maintenance. The first one consists of: surveillance (to detect degradation in optical fiber components, or any other anomalous condition not preventing the signal transmission,, testing (to measure and locate any detected degradation or anomalous condition and control (fiber identification and fiber transfer to allow the testing of the link.. In turn second one consisits of: surveillance (to detect alarms or trouble reports and activate a procedure for restoration, testing (to locate the fault and/or verify the carrier performances after the restoration and remedy (fiber identification, fiber repair or fiber transfer to restore the link.

  1. OFDM Towards Fixed and Mobile Broadband Wireless Access

    DEFF Research Database (Denmark)

    Shanker Jha, Uma; Prasad, Ramjee

    of mobile broadband wireless access and the standards developed by the IEEE 802.16 standards organization. The book gives practitioners a solid understaning of: Basic requirements of fixed and mobile broadband access technologies. Fundamentals of orthogonal frequency division multiplexing (OFDM...

  2. Broadband Adoption and Poverty: Evidence and New Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Broadband Adoption and Poverty: Evidence and New Research Directions from Latin America. Development luminaries like Jeffrey Sachs and Muhammad Yunus espouse the importance of broadband networks for promoting development. But where's the evidence to support the theory? Despite a strong national and ...

  3. The role of public initiatives facilitating investments in broadband infrastructures

    DEFF Research Database (Denmark)

    Falch, Morten; Tadayoni, Reza; Henten, Anders

    2015-01-01

    This paper discusses the role of a developmental approach to broadband policy. The policy approaches made in Denmark and Sweden are compared, and the scope for public intervention at the broadband market is discussed. The paper includes a case study on public intervention in the rural areas...

  4. 75 FR 36071 - Framework for Broadband Internet Service

    Science.gov (United States)

    2010-06-24

    ... interpret section 706(b) also to support broadband Internet services to low-income populations, such as is... Internet Service AGENCY: Federal Communications Commission. ACTION: Notice. SUMMARY: This document begins... Commission promotes investment and innovation in, and protects consumers of, broadband Internet service...

  5. Techno-economic evaluation of broadband access technologies

    DEFF Research Database (Denmark)

    Sigurdsson, Halldór Matthias; Skouby, Knud Erik

    2005-01-01

    Broadband for all is an essential element in the EU policy concerning the future of ICT-based society. The overall purpose of this paper is to present a model for evaluation of different broadband access technologies and to present some preliminary results based on the model that has been carried...

  6. Broadband tonpilz underwater acoustic transducers based on multimode optimization

    DEFF Research Database (Denmark)

    Yao, Qingshan; Jensen, Leif Bjørnø

    1997-01-01

    Head flapping has often been considered to be deleterious for obtaining a tonpilz transducer with broadband, high power performance. In the present work, broadband, high power tonpilz transducers have been designed using the finite element (FE) method. Optimized vibrational modes including the fl...

  7. Energy efficient evolution of mobile broadband networks

    Energy Technology Data Exchange (ETDEWEB)

    Micallef, G.

    2013-04-15

    existing macro base station sites together with the deployment of outdoor or indoor small cells (heterogeneous network) provide the best compromise between performance and power consumption. Focusing on one of the case studies, it is noted that the upgrade of both HSPA and LTE network layers results in the power consumption of the network increasing by a factor of 4. When coupled with the growth in capacity introduced by the various upgrades (x50), the efficiency of the network is still greatly improved. Over the evolution period, the stated increase in power consumption does not consider improvement in base station equipment. By considering a number of different equipment versions, the evolution study is further extended to also include the impact of replacing old equipment. Results show that an aggressive replacement strategy and the upgrade of sites to remote radio head can restrain the increase in power consumption of the network to just 17%. In addition to upgrading equipment, mobile network operators can further reduce power consumption by enabling a number of power saving features. These features often exploit redundancies within the network and/or the variation in traffic over a daily period. An example of such feature is sleep mode, which allows for base station sites to be systematically powered down during hours with low network traffic. While dependent on the traffic profile, within an urban area sleep mode can reduce the daily energy consumption of the network by around 20%. In addition to the different variances of sleep mode, the potential savings of other features are also described. Selecting a power efficient network capacity evolution path, replacing old and less efficient equipment, and enabling power saving features, can all considerably reduce the power consumption of future mobile broadband networks. Studies and recommendations presented within this thesis demonstrate that it is realistic for mobile network operators to boost network capacity by a

  8. Analisis Perkembangan Internet Broadband di Daerah Perbatasan Sulawesi Utara

    Directory of Open Access Journals (Sweden)

    Riva'atul Adaniah Wahab

    2016-12-01

    Full Text Available Adopsi teknologi internet broadband dapat memberikan dampak ekonomi bagi masyarakat perbatasan. Karenanya pemerataan pembangunan internet broadband di wilayah  ini harus segera diwujudkan. Penelitian deskriptif kuantitatif ini dilaksanakan di wilayah perbatasan Provinsi Sulawesi Utara untuk mengetahui kondisi aspek supply dan demand perkembangan internet broadband di wilayah tersebut. Berdasarkan hasil penelitian, dapat disimpulkan bahwa dari aspek supply, kondisi infrastruktur masih sangat kurang, ketersediaan layanan internet broadband berkualitas tinggi dengan tarif rendah juga masih sulit diwujudkan. Dari aspek demand, stigma atau persepsi masyarakat bahwa internet tidak penting menjadi salah satu faktor penyebab tidak memiliki akses internet. Adapun hambatan yang paling dominan adalah ketidakpahaman dalam penggunaan internet. Faktor ini juga menjadi mendasari literasi internet broadband masyarakat pada level 0 yaitu  tidak peduli akan pentinya internet. Menanggapai kondisi ini, penyusunan dan penetapan kebijakan serta regulasi seperti QoS layanan, tarif interkoneksi, infrastructure sharing dibuat untuk menyediakan internet broadband berkualitas tinggi dengan harga murah. Selain itu distribusi perangkat mobile berharga murah (smartphone juga perlu didorong dengan penerapan TKDN untuk produksi perangkat. Tidak kalah pentingnya adalah peningkatan literasi internet broadband masyarakat melalui sosialisasi atau pelatihan baik formal maupun nonformal. Abstract   Adoption of internet broadband internet can provide the economic impact for border communities. Hence equitable development of internet broadband in the region should be immediately implemented. This quantitative descriptive study was conducted in the border region of North Sulawesi to determine the condition of supply and demand aspects of the development of internet broadband. Based on the results, it can be concluded that from the aspect of supply, the condition of the

  9. A Dosimetric Study on Slab-pinewood-slab Phantom for Developing the Heterogeneous Chest Phantom Mimicking Actual Human Chest.

    Science.gov (United States)

    Gurjar, Om Prakash; Paliwal, Radha Kishan; Mishra, Surendra Prasad

    2017-01-01

    The aim is to study the density, isodose depths, and doses at different points in slab-pinewood-slab (SPS) phantom, solid phantom SP34 (made up of polystyrene), and chest level of actual patient for developing heterogeneous chest phantom mimicking thoracic region of human body. A 6 MV photon beam of field size of 10 cm × 10 cm was directed perpendicular to the surface of computed tomography (CT) images of chest level of patient, SPS phantom, and SP34 phantom. Dose was calculated using anisotropic analytical algorithm. Hounsfield units were used to calculate the density of each medium. Isodose depths in all the three sets of CT images were measured. Variations between planned doses on treatment planning system (TPS) and measured on linear accelerator (LA) were calculated for three points, namely, near slab-pinewood interfaces (6 and 18 cm depths) and 10 cm depth in SPS phantom and at the same depths in SP34 phantom. Density of pinewood, SP34 slabs, chest wall, lung, and soft tissue behind lung was measured as 0.329 ± 0.08, 0.999 ± 0.02, 0.898 ± 0.02, 0.291 ± 0.12, and 1.002 ± 0.03 g/cc, respectively. Depths of 100% and 90% isodose curves in all the three sets of CT images were found to be similar. Depths of 80%, 70%, 60%, 50%, and 40% isodose lines in SPS phantom images were found to be equivalent to that in chest images, while it was least in SP34 phantom images. Variations in doses calculated at 6, 10, and 18 cm depths on TPS and measured on LA were found to be 0.36%, 1.65%, and 2.23%, respectively, in case of SPS phantom, while 0.24%, 0.90%, and 0.93%, respectively, in case of SP34 slab phantom. SPS phantom seemed equivalent to the chest level of human body. Dosimetric results of this study indicate that patient-specific quality assurance can be done using chest phantom mimicking thoracic region of human body, which has been fabricated using polystyrene and pinewood.

  10. Global Subducting Slab Entrainment of Oceanic Asthenosphere: Re-examination of Sub-Slab Shear-Wave Splitting Patterns

    Science.gov (United States)

    Song, T.; Liu, L.; Kawakatsu, H.

    2011-12-01

    Oceanic asthenosphere is characterized as a low seismic velocity, low viscosity, and strongly anisotropic channel separating from the oceanic lithosphere through a sharp shear wave velocity contrast. It has been a great challenge to reconcile all these observations and ultimately illuminate the fate of oceanic asthenosphere near convergent plate margins. Sub-slab shear wave splitting patterns are particularly useful to address the fate of oceanic asthenosphere since they are directly linked to deformation induced by the mantle flow beneath the subducting slab. To address slab entrainment of oceanic asthenosphere through shear wave splitting, it is important to recognize that oceanic asthenosphere is characterized by azimuthal anisotropy (1-3%) as well as strong P wave and S wave radial anisotropy (3-7%) for horizontally travelling P wave (VPH > VPV) and S wave (VSH > VSV), making it effectively an orthorhombic medium. Here we show that entrained asthenosphere predicts sub-slab SKS splitting pattern, where the fast splitting direction changes from predominantly trench-normal under shallow subduction zones to predominantly trench-parallel under relatively steep subduction zones. This result can be recognized by the 90 degrees shift in the polarization of the fast wave at about 20 degrees incident angle, where VSH equals to VSV forming a classical point singularity (Crampin, 1991). The thickness of the entrained asthenosphere is estimated to be on the order of 100 km, which predicts SKS splitting time varying from 0.5 seconds to 2 seconds. After briefly discussing improvement of the millefeuille model (Kawakatsu et al. 2009) of the asthenosphere upon this new constraint and long wave Backus averaging of orthorhombic solid and melt, we will illustrate that, in the range of observed trench migration speed, dynamic models of 2-D mantle convection with temperature-dependent viscosity do support thick subducting slab entrainment of asthenosphere under ranges of

  11. High-transmission acoustic self-focusing and directional cloaking in a graded perforated metal slab.

    Science.gov (United States)

    Zhao, Sheng-Dong; Wang, Yue-Sheng; Zhang, Chuanzeng

    2017-06-29

    A design strategy and its modeling for high-transmission acoustic self-focusing and directional cloaking in a two-dimensional (2D) and an axisymmetric three-dimensional (3D) gradient-index phononic crystal (GRIN-PC) are reported in this paper. A gradient perforated aluminum slab sandwiched by water is considered. A low-loss directional cloaking device is achieved by controlling the matching coefficient between the slab and the water. The anisotropy coefficient that affects the scattering properties is also introduced. Furthermore, the phase discontinuity for directional cloaking inside and outside the slab is overcome by introducing a non-gradient slab having a lower group velocity behind the GRIN slab as an acoustic delay device. In addition, an axisymmetric 3D directional cloaking structure is obtained by rotating the corresponding 2D structure around the slab axis.

  12. Cenozoic tectonics of western North America controlled by evolving width of Farallon slab.

    Science.gov (United States)

    Schellart, W P; Stegman, D R; Farrington, R J; Freeman, J; Moresi, L

    2010-07-16

    Subduction of oceanic lithosphere occurs through two modes: subducting plate motion and trench migration. Using a global subduction zone data set and three-dimensional numerical subduction models, we show that slab width (W) controls these modes and the partitioning of subduction between them. Subducting plate velocity scales with W(2/3), whereas trench velocity scales with 1/W. These findings explain the Cenozoic slowdown of the Farallon plate and the decrease in subduction partitioning by its decreasing slab width. The change from Sevier-Laramide orogenesis to Basin and Range extension in North America is also explained by slab width; shortening occurred during wide-slab subduction and overriding-plate-driven trench retreat, whereas extension occurred during intermediate to narrow-slab subduction and slab-driven trench retreat.

  13. Flexural strength and behaviour of SFRSCC ribbed slab under four point bending

    Science.gov (United States)

    Ahmad, Hazrina; Hashim, Mohd Hisbany Mohd; Bakar, Afidah Abu; Hamzah, Siti Hawa; Rahman, Fadhillah Abdul

    2017-11-01

    An experimental investigation was carried out to study the ultimate strength and behaviour of SFRSCC ribbed slab under four point bending. Comparison was been made between ribbed slab that was fully reinforced with steel fibres (SFWS) with conventionally reinforced concrete ribbed slab (CS and CRC). The volume fraction of the 35 mm hooked end steel fibres used in the mix was 1% (80 kg/m3) with the aspect ratio of 65. Three full scale slab samples with the dimension of 2.8 x 1.2 m with 0.2 m thickness was constructed for the purpose of this study. The slab samples was loaded until failure in a four point bending test. As a whole, based on the results, it can be concluded that the performance of the steel fiber reinforced samples (SFWS) was found to be almost equivalent to the conventionally reinforced concrete ribbed slab sample (CRC).

  14. Long-term deformational behaviour of thick reinforced concrete slab loaded by out of plane force

    International Nuclear Information System (INIS)

    Endoh, T.; Kanazu, T.; Ishida, H.; Hirai, T.; Itoh, M.; Takei, K.

    1993-01-01

    The Advanced Thermal Reactor plant is under the design in Japan, in which the reinforced concrete slab supporting a reactor is assumed to be exposed to high temperature and low humidity conditions. The slab deforms plastically over the design period due to creep and drying shrinkage of concrete. To ensure the long term serviceability of the slab, the vertical deformation of the slab in the design period has to be estimated. In the study, the experimental work using 1/5 scale partial models of the slab and the analytical simulations were carried out. Comparing the results of the analysis and the tests, it is confirmed that the analysis suggested here is a suitable procedure to estimate the long term deformation of the slab. (author)

  15. Broadband WET: a novel technique for quantitative characterization of minor components in foods.

    Science.gov (United States)

    Furihata, Kazuo; Zhang, Jing; Koda, Masanori; Miyakawa, Takuya; Tanokura, Masaru

    2014-07-01

    NMR analysis of foods frequently suffers from a problem of dynamic range, which limits the detection of minor components due to the huge signals of water and major components such as sugars. In the present study, we propose a new method named as 'broadband WET'. This pulse scheme was applied to persimmon fruit juice for saturating the resonances of water and sugars, which covered a broad bandwidth. In comparison with the conventional solvent suppression methods such as WET and DPFGSE-WATERGATE, it was shown that broadband WET provided highly selective suppression of resonances covering an extensive bandwidth and quantitative signals of minor components without distortion. The proposed method is suitable to detect quantitative signals of the minor components with a high sensitivity. Copyright © 2014 John Wiley & Sons, Ltd.

  16. A Highly Efficient Broadband Class-E Power Amplifier with Nonlinear Shunt Capacitance

    Directory of Open Access Journals (Sweden)

    Ninh Dang-Duy

    2017-10-01

    Full Text Available A new approach to designing a broadband and highly efficient class-E power amplifier based on nonlinear shunt capacitance analysis is proposed. The nonlinear shunt capacitance method accurately extracts optimum class-E power amplifier parameters, including an external shunt capacitance and an output impedance, at different frequencies. The dependence of the former parameter on the frequency is considered to select an optimal value of external shunt capacitor. Then, upon determining the latter parameter, an output matching network is optimized to obtain the highest efficiency across the bandwidth of interest. An analytical approach is presented to design the broadband class-E power amplifier of a MOSFET transistor. The proposed method is experimentally verified by a 140–170 MHz class-E power amplifier design with maximum added power efficiency of 82% and output power of 34 dBm.

  17. Broadband PLC for Clustered Advanced Metering Infrastructure (AMI Architecture

    Directory of Open Access Journals (Sweden)

    Augustine Ikpehai

    2016-07-01

    Full Text Available Advanced metering infrastructure (AMI subsystems monitor and control energy distribution through exchange of information between smart meters and utility networks. A key challenge is how to select a cost-effective communication system without compromising the performance of the applications. Current communication technologies were developed for conventional data networks with different requirements. It is therefore necessary to investigate how much of existing communication technologies can be retrofitted into the new energy infrastructure to cost-effectively deliver acceptable level of service. This paper investigates broadband power line communications (BPLC as a backhaul solution in AMI. By applying the disparate traffic characteristics of selected AMI applications, the network performance is evaluated. This study also examines the communication network response to changes in application configurations in terms of packet sizes. In each case, the network is stress-tested and performance is assessed against acceptable thresholds documented in the literature. Results show that, like every other communication technology, BPLC has certain limitations; however, with some modifications in the network topology, it indeed can fulfill most AMI traffic requirements for flexible and time-bounded applications. These opportunities, if tapped, can significantly improve fiscal and operational efficiencies in AMI services. Simulation results also reveal that BPLC as a backhaul can support flat and clustered AMI structures with cluster size ranging from 1 to 150 smart meters.

  18. Broadband and short (10-ps) pulse generation on Nova

    International Nuclear Information System (INIS)

    Perry, M.D.; Browning, D.; Bibeau, C.; Patterson, F.G.; Wilcox, R.; Henesian, M.

    1990-01-01

    The ability to produce high power broadband pulses for purposes of focal spot beam smoothing has recently become an important issue in inertial confinement fusion (ICF). As the first step toward the generation and propagation of such pulses on Nova, the authors have performed a series of experiments with 10-ps pulses. Aside from the inherently broad bandwidth, these short pulses have important applications in ICF experiments and x-ray laser research. The author's experimental results are discussed. The short pulses were produced by diffraction grating pulse compression of chirped pulses formed from self-phase modulation in a single-mode 10-m fused silica fiber. Use of such a short fiber produces a nonlinearly chirped spectrum of 0.74 nm. The central nearly linearly chirped 0.26 nm is selected by polarization discrimination and compressed using 1800-line/mm diffraction gratings to a nearly Gaussian pulse of 10 ps FWHM with an energy contrast ratio of 20:1. This 1-nJ pulse is injected into a Nova amplifier chain with selected amplifiers unfired

  19. Multicarrier Block-Spread CDMA for Broadband Cellular Downlink

    Directory of Open Access Journals (Sweden)

    Leus Geert

    2004-01-01

    Full Text Available Effective suppression of multiuser interference (MUI and mitigation of frequency-selective fading effects within the complexity constraints of the mobile constitute major challenges for broadband cellular downlink transceiver design. Existing wideband direct-sequence (DS code division multiple access (CDMA transceivers suppress MUI statistically by restoring the orthogonality among users at the receiver. However, they call for receive diversity and multichannel equalization to improve the fading effects caused by deep channel fades. Relying on redundant block spreading and linear precoding, we design a so-called multicarrier block-spread- (MCBS-CDMA transceiver that preserves the orthogonality among users and guarantees symbol detection, regardless of the underlying frequency-selective fading channels. These properties allow for deterministic MUI elimination through low-complexity block despreading and enable full diversity gains, irrespective of the system load. Different options to perform equalization and decoding, either jointly or separately, strike the trade-off between performance and complexity. To improve the performance over multi-input multi-output (MIMO multipath fading channels, our MCBS-CDMA transceiver combines well with space-time block-coding (STBC techniques, to exploit both multiantenna and multipath diversity gains, irrespective of the system load. Simulation results demonstrate the superior performance of MCBS-CDMA compared to competing alternatives.

  20. Analytical model for shear strength of end slabs of prestressed concrete nuclear reactor vessels

    International Nuclear Information System (INIS)

    Abdulrahman, H.O.; Sozen, M.A.; Schnobrich, W.C.

    1979-04-01

    The results are presented of an investigation of the behavior and strength of flat end slabs of cylindrical prestressed concrete nuclear reactor vessels. The investigation included tests of ten small-scale pressure vessels and development of a nonlinear finite-element model to simulate the deformation response and strength of the end slabs. Because earlier experimental studies had shown that the flexural strength of the end slab could be calculated using intelligible procedures, the emphasis of this investigation was on shear strength

  1. Bearing capacity analysis of RC “pi” slab under normal and fire conditions

    OpenAIRE

    Goljevšček, Blaž

    2010-01-01

    In the graduation thesis, we analyze the bearing capacity of the reinforced concrete “phi” slab under normal and fire conditions. In the beginning, we present the dimensioning process of the slab according to the Eurocode principles and rules, in terms of meeting the requirements for mechanical resistance, functionality and durability. Next, we use the finite element method to analyze a nonlinear mechanical response of the “phi” slab under the influence of short-term static load and compare t...

  2. Disorders influences on the focusing effect of all-dielectric photonic crystal slab superlens

    Energy Technology Data Exchange (ETDEWEB)

    Hu Xiaoyong; Xin Cheng [State Key Laboratory for Mesoscopic Physics and Department of Physics, Peking University, Beijing 100871 (China); Gong Qihuang [State Key Laboratory for Mesoscopic Physics and Department of Physics, Peking University, Beijing 100871 (China)], E-mail: qhgong@pku.edu.cn

    2009-04-13

    The influences of structure disorders on the subwavelength focusing properties of an all-dielectric photonic crystal slab superlens are theoretically studied. The structure disorders are considered as randomly perturbing the position or diameter of air holes of the photonic crystal slab. The results show that the photonic crystal slab superlens can tolerate within 10% degree of positional disorder or 15% degree of diameter disorder without destroying the focusing function.

  3. Disorders influences on the focusing effect of all-dielectric photonic crystal slab superlens

    International Nuclear Information System (INIS)

    Hu Xiaoyong; Xin Cheng; Gong Qihuang

    2009-01-01

    The influences of structure disorders on the subwavelength focusing properties of an all-dielectric photonic crystal slab superlens are theoretically studied. The structure disorders are considered as randomly perturbing the position or diameter of air holes of the photonic crystal slab. The results show that the photonic crystal slab superlens can tolerate within 10% degree of positional disorder or 15% degree of diameter disorder without destroying the focusing function.

  4. A numerical study on the fatigue life design of concrete slabs for railway

    OpenAIRE

    Poveda Bautista, Elisa; Rena C., Yu; Lancha Fernández, Juan Carlos; Ruiz López, Gonzalo Francisco

    2015-01-01

    With the growing use of high-speed trains, non-ballasted tracks have become more popular compared to ballasted ones. However, the study on fatigue evaluation in concrete slabs under train load has been rather limited. This work presents a numerical study on the fatigue life design of concrete slabs for railway tracks. A finite element model for a three-slab track system is established for extracting the principal vibration modes and transient analysis under time-dependent loads. T...

  5. Mechanical Model for flexural behaviour of slab-column connections under seismically induced deformations

    OpenAIRE

    Drakatos Ioannis-Sokratis; Muttoni Aurelio; Beyer Katrin

    2014-01-01

    Reinforced concrete (RC) flat slabs supported on columns are one of the most widely used structural systems for office and industrial buildings. In regions of medium to high seismic risk RC walls are typically added as lateral force resisting system and to increase the lateral stiffness and strength. Although slab-column systems are not expected to contribute to the lateral resistance of the structure due to their low stiffness, the slab-column connection have to have the capacity to follow t...

  6. Simulating the effect of slab features on vapor intrusion of crack entry

    OpenAIRE

    Yao, Yijun; Pennell, Kelly G.; Suuberg, Eric M.

    2013-01-01

    In vapor intrusion screening models, a most widely employed assumption in simulating the entry of contaminant into a building is that of a crack in the building foundation slab. Some modelers employed a perimeter crack hypothesis while others chose not to identify the crack type. However, few studies have systematically investigated the influence on vapor intrusion predictions of slab crack features, such as the shape and distribution of slab cracks and related to this overall building founda...

  7. Broadband Optical Access Technologies to Converge towards a Broadband Society in Europe

    Science.gov (United States)

    Coudreuse, Jean-Pierre; Pautonnier, Sophie; Lavillonnière, Eric; Didierjean, Sylvain; Hilt, Benoît; Kida, Toshimichi; Oshima, Kazuyoshi

    This paper provides insights on the status of broadband optical access market and technologies in Europe and on the expected trends for the next generation optical access networks. The final target for most operators, cities or any other player is of course FTTH (Fibre To The Home) deployment although we can expect intermediate steps with copper or wireless technologies. Among the two candidate architectures for FTTH, PON (Passive Optical Network) is by far the most attractive and cost effective solution. We also demonstrate that Ethernet based optical access network is very adequate to all-IP networks without any incidence on the level of quality of service. Finally, we provide feedback from a FTTH pilot network in Colmar (France) based on Gigabit Ethernet PON technology. The interest of this pilot lies on the level of functionality required for broadband optical access networks but also on the development of new home network configurations.

  8. Contact Loss beneath Track Slab Caused by Deteriorated Cement Emulsified Asphalt Mortar: Dynamic Characteristics of Vehicle-Slab Track System and Prototype Experiment

    Directory of Open Access Journals (Sweden)

    Dan Liu

    2016-01-01

    Full Text Available The contact loss beneath track slab caused by deteriorated cement emulsified asphalt mortar (CA mortar has been one of the main diseases occurring in the CRTS- (China Railway Track System- I Slab Track of high-speed railway in China. Based on the slab track design theory and the vehicle-track coupling vibration theory, a vehicle-track vertical coupling dynamic FEM model was established to analyze the influence of the contact loss length on the dynamic characteristics of vehicle and track subsystems at different train speeds. A prototype dynamic characteristic experimental test of CRTS-I Slab Track with CA mortar contact loss was conducted to verify the FEM model results. The train load was generated by the customized ZSS50 excitation car. The results showed that when the operation speed is less than 300 km/h, the contact loss with length smaller than 2.0 m barely affects the running smoothness ride safety of vehicle. The contact loss length effect on the dynamic characteristics of track subsystem is pronounced, especially on the track slab. Once the contact loss beneath the track slab occurs, the vibration displacement and the acceleration of the track slab increase rapidly, while it has little influence on the displacement and acceleration of the concrete roadbed.

  9. High efficiency and broadband acoustic diodes

    Science.gov (United States)

    Fu, Congyi; Wang, Bohan; Zhao, Tianfei; Chen, C. Q.

    2018-01-01

    Energy transmission efficiency and working bandwidth are the two major factors limiting the application of current acoustic diodes (ADs). This letter presents a design of high efficiency and broadband acoustic diodes composed of a nonlinear frequency converter and a linear wave filter. The converter consists of two masses connected by a bilinear spring with asymmetric tension and compression stiffness. The wave filter is a linear mass-spring lattice (sonic crystal). Both numerical simulation and experiment show that the energy transmission efficiency of the acoustic diode can be improved by as much as two orders of magnitude, reaching about 61%. Moreover, the primary working band width of the AD is about two times of the cut-off frequency of the sonic crystal filter. The cut-off frequency dependent working band of the AD implies that the developed AD can be scaled up or down from macro-scale to micro- and nano-scale.

  10. Broadband terahertz modulator based on graphene metamaterials

    Science.gov (United States)

    Huang, Zehua; Han, Qi; Ji, Chunhui; Wang, Jun; Jiang, Yadong

    2018-03-01

    Tunable complementary split ring resonators (CSRRs) based on monolayer graphene are presented in terahertz regime. By applying different gate voltage, the Fermi level and optical conductivity of monolayer graphene pattern can be changed. Here, we employ a numerical simulation to study the interaction of light with graphene CSRRs. The results indicate that the extinction in transmission becomes stronger, and the resonance frequency presents blue shift with higher Fermi level of the graphene pattern. Three pronounced resonant peaks appear which can be modulated dynamically in the range of 1-2THz and 3-7THz, and realizing dynamic broadband terahertz modulation, the modulation depth exceeds 85% at all three resonant peaks, the highest modulation depth reaches 98.8% at 7.47THz.

  11. Validating data analysis of broadband laser ranging

    Science.gov (United States)

    Rhodes, M.; Catenacci, J.; Howard, M.; La Lone, B.; Kostinski, N.; Perry, D.; Bennett, C.; Patterson, J.

    2018-03-01

    Broadband laser ranging combines spectral interferometry and a dispersive Fourier transform to achieve high-repetition-rate measurements of the position of a moving surface. Telecommunications fiber is a convenient tool for generating the large linear dispersions required for a dispersive Fourier transform, but standard fiber also has higher-order dispersion that distorts the Fourier transform. Imperfections in the dispersive Fourier transform significantly complicate the ranging signal and must be dealt with to make high-precision measurements. We describe in detail an analysis process for interpreting ranging data when standard telecommunications fiber is used to perform an imperfect dispersive Fourier transform. This analysis process is experimentally validated over a 27-cm scan of static positions, showing an accuracy of 50 μm and a root-mean-square precision of 4.7 μm.

  12. Digital broadband linearization of optical links.

    Science.gov (United States)

    Lam, Daniel; Fard, Ali M; Buckley, Brandon; Jalali, Bahram

    2013-02-15

    We present a digital postprocessing linearization technique to efficiently suppress dynamic distortions added to a wideband signal in an analog optical link. Our technique achieves up to 35 dB suppression of intermodulation distortions over multiple octaves of signal bandwidth. In contrast to conventional linearization methods, it does not require excessive analog bandwidth for performing digital correction. This is made possible by regenerating undesired distortions from the captured output, and subtracting it from the distorted digitized signal. Moreover, we experimentally demonstrate a record spurious-free dynamic range of 120 dB·Hz(2/3) over a 6 GHz electrical signal bandwidth. While our digital broadband linearization technique advances state-of-the-art optical links, it can also be applied to other nonlinear dynamic systems.

  13. Broadband optical modulators based on graphene supercapacitors.

    Science.gov (United States)

    Polat, Emre O; Kocabas, Coskun

    2013-01-01

    Optical modulators are commonly used in communication and information technology to control intensity, phase, or polarization of light. Electro-optic, electroabsorption, and acousto-optic modulators based on semiconductors and compound semiconductors have been used to control the intensity of light. Because of gate tunable optical properties, graphene introduces new potentials for optical modulators. The operation wavelength of graphene-based modulators, however, is limited to infrared wavelengths due to inefficient gating schemes. Here, we report a broadband optical modulator based on graphene supercapacitors formed by graphene electrodes and electrolyte medium. The transparent supercapacitor structure allows us to modulate optical transmission over a broad range of wavelengths from 450 nm to 2 μm under ambient conditions. We also provide various device geometries including multilayer graphene electrodes and reflection type device geometries that provide modulation of 35%. The graphene supercapacitor structure together with the high-modulation efficiency can enable various active devices ranging from plasmonics to optoelectronics.

  14. Frequency Doubling Broadband Light in Multiple Crystals

    International Nuclear Information System (INIS)

    Alford, William J.; Smith, Arlee V.

    2000-01-01

    The authors compare frequency doubling of broadband light in a single nonlinear crystal with doubling in five crystals with intercrystal temporal walk off compensation, and with doubling in five crystals adjusted for offset phase matching frequencies. Using a plane-wave, dispersive numerical model of frequency doubling they study the bandwidth of the second harmonic and the conversion efficiency as functions of crystal length and fundamental irradiance. For low irradiance the offset phase matching arrangement has lower efficiency than a single crystal of the same total length but gives a broader second harmonic bandwidth. The walk off compensated arrangement gives both higher conversion efficiency and broader bandwidth than a single crystal. At high irradiance, both multicrystal arrangements improve on the single crystal efficiency while maintaining broad bandwidth

  15. Broadband plasmon induced transparency in terahertz metamaterials

    KAUST Repository

    Zhu, Zhihua

    2013-04-25

    Plasmon induced transparency (PIT) could be realized in metamaterials via interference between different resonance modes. Within the sharp transparency window, the high dispersion of the medium may lead to remarkable slow light phenomena and an enhanced nonlinear effect. However, the transparency mode is normally localized in a narrow frequency band, which thus restricts many of its applications. Here we present the simulation, implementation, and measurement of a broadband PIT metamaterial functioning in the terahertz regime. By integrating four U-shape resonators around a central bar resonator, a broad transparency window across a frequency range greater than 0.40 THz is obtained, with a central resonance frequency located at 1.01 THz. Such PIT metamaterials are promising candidates for designing slow light devices, highly sensitive sensors, and nonlinear elements operating over a broad frequency range. © 2013 IOP Publishing Ltd.

  16. Diode-side-pumped monolithic Nd:YAG slab laser

    Science.gov (United States)

    Šulc, Jan; Jelínek, Michal; Kubeček, Václav; Jelínková, Helena; Nejezchleb, Karel; Škoda, Václav

    2017-05-01

    Compact, high-efficient, side-pumped monolithic Nd:YAG slab laser is presented. Designed active crystal shape ensures four internal reflections of generated laser radiation forming a ring resonator with high gain. A horizontal projection of the active medium form was a isosceles trapezoid with 18.6 mm long base, and 5 mm height. The angels between long base and legs are 87 deg. The thickness of the slab was 4 mm. Both base-sides and one leg-side was high reflective for lasing radiation. Second leg-side was partially reflective for lasing radiation and serves as an output coupler. The longer base-side was highly transparent for pumping radiation. The opposite base-side was highly reflecting for pump. To increase the pump absorption efficiency Nd-doping concentration was 1.4 % Nd/Y. As a pump source, single-bar quasi-cw fast-axis collimated laser diode JOLD-180-QPFN (Jenoptik) with peak power 180 W at 808 nm and output beam 10 0.9 mm without any further optics was used for slab side-pumping. The pumping pulses with repetition rate 5 Hz were 250 μs long (maximum pump energy 39 mJ). The Nd:YAG laser was operated at 1.06 µm. Two external mirrors (one totally reflecting, second with reflectivity 80 % at 1.06 μm) were used to form the oscillator. The laser was tested in the free-running regime. The maximum laser output energy reached was 5.9 mJ which corresponds to optical-to-optical efficiency of 15 %. The laser slope efficiency in respect to laser diode output was 20 %. The divergence of multimode output beam was 7 × 2.5mrad.

  17. A generalized slab-wise framework for parallel transmit multiband RF pulse design.

    Science.gov (United States)

    Wu, Xiaoping; Schmitter, Sebastian; Auerbach, Edward J; Uğurbil, Kâmil; Van de Moortele, Pierre-François

    2016-04-01

    We propose a new slab-wise framework to design parallel transmit multiband pulses for volumetric simultaneous multislice imaging with a large field of view along the slice direction (FOVs). The slab-wise framework divides FOVs into a few contiguous slabs and optimizes pulses for each slab. Effects of relevant design parameters including slab number and transmit B1 (B1+) mapping slice placement were investigated for human brain imaging by designing pulses with global or local SAR control based on electromagnetic simulations of a 7T head RF array. Pulse design using in vivo B1+ maps was demonstrated and evaluated with Bloch simulations. RF performance with respect to SAR reduction or B1+ homogenization across the entire human brain improved with increasing slabs; however, this improvement was nonlinear and leveled off at ∼12 slabs when the slab thickness reduced to ∼12 mm. The impact of using different slice placements for B1+ mapping was small. Compared with slice-wise approaches where each of the many imaging slices requires both B1+ mapping and pulse optimization, the proposed slab-wise design framework attained comparable RF performance while drastically reducing the number of required pulses; therefore, it can be used to increase time efficiency for B1+ mapping, pulse calculation, and sequence preparation. © 2015 Wiley Periodicals, Inc.

  18. Meteorological variables to aid forecasting deep slab avalanches on persistent weak layers

    Science.gov (United States)

    Marienthal, Alex; Hendrikx, Jordy; Birkeland, Karl; Irvine, Kathryn M.

    2015-01-01

    Deep slab avalanches are particularly challenging to forecast. These avalanches are difficult to trigger, yet when they release they tend to propagate far and can result in large and destructive avalanches. We utilized a 44-year record of avalanche control and meteorological data from Bridger Bowl ski area in southwest Montana to test the usefulness of meteorological variables for predicting seasons and days with deep slab avalanches. We defined deep slab avalanches as those that failed on persistent weak layers deeper than 0.9 m, and that occurred after February 1st. Previous studies often used meteorological variables from days prior to avalanches, but we also considered meteorological variables over the early months of the season. We used classification trees and random forests for our analyses. Our results showed seasons with either dry or wet deep slabs on persistent weak layers typically had less precipitation from November through January than seasons without deep slabs on persistent weak layers. Days with deep slab avalanches on persistent weak layers often had warmer minimum 24-hour air temperatures, and more precipitation over the prior seven days, than days without deep slabs on persistent weak layers. Days with deep wet slab avalanches on persistent weak layers were typically preceded by three days of above freezing air temperatures. Seasonal and daily meteorological variables were found useful to aid forecasting dry and wet deep slab avalanches on persistent weak layers, and should be used in combination with continuous observation of the snowpack and avalanche activity.

  19. Structured mass density slab as a waveguide of fast magnetoacoustic waves

    Science.gov (United States)

    Jelínek, P.; Karlický, M.

    Coronal loops are waveguides for magnetohydrodynamic (MHD) waves. These loops are expected to be structured. Therefore, in the present paper, we numerically studied the propagation of the fast MHD waves in the structured density slab (composed from a broad density slab with one axisymmetric narrow sub-slab superposed), and analysed the wave signals. Then, this structured slab was divided into its components, i.e., to simple broad and narrow slabs and the same analysis was made. We compared results of both these cases. For the calculations we adopted a two-dimensional (2D) magnetohydrodynamic (MHD) model, in which we solved a full set of ideal time-dependent MHD equations using the FLASH code, applying the adaptive mesh refinement (AMR) method. To initiate the fast sausage magnetoacoustic waves, we used axisymmetric Gaussian velocity perturbation. Wave signals were detected in different locations along the slab and as a diagnostic tool of these waves, the wavelet analysis method has been used. We found that for the structured density slab with sufficiently sharp boundaries, i.e., for good quality waveguides (without an energy leakage), the guided waves in the structured slab behave similarly as in its separated (simple slab) components.

  20. Flexural Strengthening of RC Slabs Using a Hybrid FRP-UHPC System Including Shear Connector

    Directory of Open Access Journals (Sweden)

    Jiho Moon

    2017-01-01

    Full Text Available A polymeric hybrid composite system made of UHPC and CFRP was proposed as a retrofit system to enhance flexural strength and ductility of RC slabs. While the effectiveness of the proposed system was confirmed previously through testing three full-scale one-way slabs having two continuous spans, the slabs retrofitted with the hybrid system failed in shear. This sudden shear failure would stem from the excessive enhancement of the flexural strength over the shear strength. In this study, shear connectors were installed between the hybrid system and a RC slab. Using simple beam, only positive moment section was examined. Two full-scale RC slabs were cast and tested to failure: the first as a control and the second using this new strengthening technique. The proposed strengthening system increased the ultimate load carrying capacity of the slab by 70%, the stiffness by 60%, and toughness by 128%. The efficiency of shear connectors on ductile behavior of the retrofitted slab was also confirmed. After the UHPC top is separated from the slab, the shear connector transfer shear load and the slab system were in force equilibrium by compression in UHPC and tension in CFRP.

  1. Free subduction dynamics of a thermo-mechanical slab with non-linear rheology

    Science.gov (United States)

    Holt, A. F.; Becker, T. W.; Buffett, B. A.

    2012-12-01

    We investigate the dynamic controls on single plate subduction in a visco-plastic rheology using a 2D set up of the finite element code, CitcomCU. In contrast to previous studies, which focus largely on compositional slabs (e.g. Enns et al., 2005), we focus on thermal slabs (i.e. include effects of thermal diffusion). We analyse slabs that develop from plates both with uniform initial thicknesses and half-space cooling plates with thicknesses that vary with sqrt(x). A pseudo-plastic rheology facilitates the decoupling of the slab from the free slip upper surface. It is found that thermal slabs have lower strain rates in the bending region, due to the cooling upper boundary temperature condition, and so lower yield stresses are required to decouple thermal slabs than compositional slabs. As in previous work, it is found that stronger, thicker slabs promote trench advance (after the initial advancing phase). Both boundary conditions (basal and side) and incorporating a plate with half-space cooling thickness variations are shown to have a significant effect on slab dynamics, particularly on the maximum amount of trench retreat. Subsequently, models with non-Newtonian, stress-dependent rheologies are compared to Newtonian models with equivalent slab-mantle viscosity contrasts. Models with power law exponents of both 3, corresponding to dislocation creep, and a large exponent of 14, corresponding to near-pure plasticity (see Buffett and Becker, 2012), are analysed. It is found that, particularly for the n=14 case, the inclusion of a stress dependent rheology dramatically reduces the timescales of both trench migration and slab descent, while modifying slab morphology to a much lesser degree. Using a temperature threshold to confine the non-Newtonian rheology to within the slab prevents weakening in the surrounding mantle and so increases the subduction timescales to values that lie between the equivalent Newtonian and non-Newtonian (non-confined) timescales. While all

  2. Tectonic evolution of the Mexico flat slab and patterns of intraslab seismicity.

    Science.gov (United States)

    Moresi, L. N.; Sandiford, D.

    2017-12-01

    The Cocos plate slab is horizontal for about 250 km beneath the Guerrero region of southern Mexico. Analogous morphologies can spontaneously develop in subduction models, through the presence of a low-viscosity mantle wedge. The Mw 7.1 Puebla earthquake appears to have ruptured the inboard corner of the Mexican flat slab; likely in close proximity to the mantle wedge corner. In addition to the historical seismic record, the Puebla earthquake provides a valuable constraint through which to assess geodynamic models for flat slab evolution. Slab deformation predicted by the "weak wedge" model is consistent with past seismicity in the both the upper plate and slab. Below the flat section, the slab is anomalously warm relative to its depth; the lack of seismicity in the deeper part of the slab fits the global pattern of temperature-controlled slab seismicity. This has implications for understanding the deeper structure of the slab, including the seismic hazard from source regions downdip of the Puebla rupture (epicenters closer to Mexico City). While historical seismicity provides a deformation pattern consistent with the weak wedge model , the Puebla earthquake is somewhat anomalous. The earthquake source mechanism is consistent with stress orientations in our models, however it maps to a region of relatively low deviatoric stress.

  3. Analysis of segregation solute redistribution and centerline in continuously cast thin slab

    Directory of Open Access Journals (Sweden)

    Changwen MA

    2004-11-01

    Full Text Available A model has been built to calculate the solute redistribution in continuously cast thin slab and the effect of the fluid flow in mush on the centerline segregation was analyzed. The corresponding simulation program was developed by applying the SIMPLER algorithm. The momentum, energy and species conservation equations were solved simultaneously. The macro-segregation of a 3-D thin slab with 900 mm x 50 mm cross section was simulated. The obtained results show that negative segregation forms near the slab surface and severe centerline segregation forms in the mid-thickness plane. The species concentration in the centerline of the slab increases obviously at the final solidification stage.

  4. Usage of prestressed vertical bolts for retrofitting flat slabs damaged due to punching shear

    Directory of Open Access Journals (Sweden)

    Hamed S. Askar

    2015-09-01

    An experimental investigation with the objective of retrofitting flat slabs damaged due to punching shear using prestressed vertical bolts is presented in this paper. The parameters examined in this study are vertical prestressed bolts with different ratios within the slab thickness, slab thickness and central column size. Through the experimental tests the load carrying capacity, deformation characteristics and the cracking behavior have been investigated. A comparison between the behavior of retrofitted slabs and their references showed that the proposed system of repair is effective and could be used in practice. A comparison between the experimental results and calculated punching failure load based on the formulas adopted by different codes, showed a reasonable agreement.

  5. A new crack propagation criterion for skier-triggered snow slab avalanches

    OpenAIRE

    Gaume Johan; Reuter Benjamin; van Herwijnen Alec; Schweizer Jürg

    2016-01-01

    Dry snow slab avalanches begin with a local failure in a weak snowpack layer buried below cohesive slab layers. If the size of the failed zone exceeds a critical length rapid crack propagation occurs possibly followed by slab release if the slope is steep enough. The probability to trigger a slab avalanche by a skier or a snowmobile is generally described by classical stability indices which do not account for crack propagation. In this study we propose a new model to evaluate the conditions ...

  6. CAISSON TYPE HOLLOW FLOOR SLABS OF MONOLITHIC MULTI-STOREYED BUILDINGS

    Directory of Open Access Journals (Sweden)

    Malakhova Anna Nikolaevna

    2016-06-01

    Full Text Available One of the disadvantages of building structures made of reinforced concrete is their considerable weight. One of the trends to decrease the weight of concrete structures, including floor slabs, is the arrangement of voids in the cross-sectional building structures. In Russian and foreign practice paper, cardboard and plastic tubes has been used for creation of voids in the construction of monolithic floor slabs. Lightweight concretes were also used for production of precast hollow core floor slabs. The article provides constructive solutions of precast hollow core floor slabs and solid monolithic slabs that were used in the construction of buildings before wide use of large precast hollow core floor slabs. The article considers the application of caisson hollow core floor slabs for modern monolithic multi-storeyed buildings. The design solutions of such floor slabs, experimental investigations and computer modeling of their operation under load were described in this article. The comparative analysis of the calculation results of computer models of a hollow slabs formed of rod or plastic elements showed the similarity of calculation results.

  7. Research on mechanical behavior of casting slab during dynamic soft reduction

    Science.gov (United States)

    Qin, Qin; Huang, Jianlin; Zhou, Daomou; Yang, Xiaoying

    2017-10-01

    A three-dimensional dynamic solidification model incorporating the thermo-elastic-plastic coupling model has been proposed in this paper by ABAQUS considering the dynamic contact between the slab and rolls. The thermo-mechanical coupling model produces outputs such as temperature and mechanical behavior of the slab. And the stress-strain distribution of the high-temperature slab at the solidification end has been investigated in this paper. The influences of various reduction interval, reduction amount and reduction distribution on mechanical behavior of casting slab have been systematically discussed.

  8. Patient portals and broadband internet inequality.

    Science.gov (United States)

    Perzynski, Adam T; Roach, Mary Joan; Shick, Sarah; Callahan, Bill; Gunzler, Douglas; Cebul, Randall; Kaelber, David C; Huml, Anne; Thornton, John Daryl; Einstadter, Douglas

    2017-09-01

    Patient portals have shown potential for increasing health care quality and efficiency. Internet access and other factors influencing patient portal use could worsen health disparities. Observational study of adults with 1 or more visits to the outpatient clinics of an urban public health care system from 2012 to 2015. We used mixed effects logistic regression to evaluate the association between broadband internet access and (1) patient portal initiation (whether a patient logged in at least 1 time) and (2) messaging, controlling for demographic and neighborhood characteristics. There were 243 248 adults with 1 or more visits during 2012-2015 and 70 835 (29.1%) initiated portal use. Portal initiation was 34.1% for whites, 23.4% for blacks, and 23.8% for Hispanics, and was lower for Medicaid (26.5%), Medicare (23.4%), and uninsured patients (17.4%) than commercially insured patients (39.3%). In multivariate analysis, both initiation of portal use (odds ratio [OR] = 1.24 per quintile, 95% confidence interval [CI], 1.23-1.24, P  internet access. The majority of adults with outpatient visits to a large urban health care system did not use the patient portal, and initiation of use was lower for racial and ethnic minorities, persons of lower socioeconomic status, and those without neighborhood broadband internet access. These results suggest the emergence of a digital divide in patient portal use. Given the scale of investment in patient portals and other internet-dependent health information technologies, efforts are urgently needed to address this growing inequality. © The Author 2017. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com

  9. The Slab Method to Measure the Topological Susceptibility

    CERN Document Server

    Bietenholz, Wolfgang; de Forcrand, Philippe; Dromard, Arthur; Gerber, Urs

    2016-10-11

    In simulations of a model with topological sectors, algorithms which proceed in small update steps tend to get stuck in one sector, especially on fine lattices. This distorts the numerical results, in particular it is not straightforward to measure the topological susceptibility chi_t. We test a method to measure chi_t even if configurations from only one sector are available. It is based on the topological charges in sub-volumes, which we denote as "slabs". This enables the evaluation of chi_t, as we demonstrate with numerical results for non-linear sigma-models and for 2-flavour QCD.

  10. Slab-diffusion approximation from time-constant-like calculations

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, R. W.

    1976-12-01

    Two equations were derived which describe the quantity and any fluid diffused from a slab as a function of time. One equation is applicable to the initial stage of the process; the other to the final stage. Accuracy is 0.2 percent at the one point where both approximations apply and where accuracy of either approximation is the poorest. Characterizing other rate processes might be facilitated by the use of the concept of NOLOR (normal of the logarithm of the rate) and its time dependence. (auth)

  11. Slab-diffusion approximation from time-constant-like calculations

    International Nuclear Information System (INIS)

    Johnson, R.W.

    1976-12-01

    Two equations were derived which describe the quantity and any fluid diffused from a slab as a function of time. One equation is applicable to the initial stage of the process; the other to the final stage. Accuracy is 0.2 percent at the one point where both approximations apply and where accuracy of either approximation is the poorest. Characterizing other rate processes might be facilitated by the use of the concept of NOLOR (normal of the logarithm of the rate) and its time dependence

  12. Industrial online surface defects detection in continuous casting hot slabs

    Science.gov (United States)

    Alvarez, Ignacio; Marina, Jorge; Enguita, Jose Maria; Fraga, Cesar; Garcia, Ricardo

    2009-06-01

    Early surface defects inspection in hot steel products is a difficult task, but can help to reduce significantly production costs. This is the case of steel slabs when they are produced in the continuous casting line. Conoscopic holography phase-based long stand-off profilometers have shown to be a great tool for this kind of inspection, and a breakthrough system based on them is being used for more than 2 years in production conditions with high reliability and economical impact. This paper presents the results of this system and the challenges it has overcome: hot material up to 900°C, dust, scale over the inspected surface.

  13. Lower bound limit analysis of slabs with nonlinear yield criteria

    DEFF Research Database (Denmark)

    Krabbenhøft, Kristian; Damkilde, Lars

    2002-01-01

    A finite element formulation of the limit analysis of perfectly plastic slabs is given. An element with linear moment fields for which equilibrium is satisfied exactly is used in connection with an optimization algorithm taking into account the full nonlinearity of the yield criteria. Both load...... and material optimization problems are formulated and by means of the duality theory of linear programming the displacements are extracted from the dual variables. Numerical examples demonstrating the capabilities of the method and the effects of using a more refined representation of the yield criteria...

  14. CONCRETE PROPERTIES IMPROVEMENT OF SLAB TRACKS USING CHEMICAL ADDITIVES

    Directory of Open Access Journals (Sweden)

    V. V. Pristinskaya

    2015-11-01

    Full Text Available Purpose. On the Railways of Ukraine a very large number of slab tracks are operated with cracks. Many scientific works of previous years are dedicated to improving the design of slab tracks. The main causes of defects are: poor exploitation of the track; insufficient physic-mechanical characteristics of concrete; poor quality of initial materials. It is therefore necessary to develop an optimum concrete mix for the manufacture of these concrete products. Methodology. To assess the impact of individual factors and effects of their interactions on properties of concrete mix and concrete method of experimental and statistical modeling was used. At this, methodological fundamentals of mathematical experiment planning in concrete technology and modern methods of optimization of composite materials were taking into account. Based on the obtained data during the planned experiment conducting, including15 studies and using the computer program MathCad, were obtained the regression equations, which describe the relevant physical and mechanical properties of concrete. On the basis of the equations with the help of computer program MATLAB R2012b the graphs were drawn, illustrating the dependences of system response from the changes of two factors at a fixed value of the third factor. Findings. Firstly was the analysis of cracks that occur in the process of operation in the constructions of slab tracks. Further reasons of possible occurrence of these cracks were presented. In the process of the conducted research the author has concluded that for rational concrete mix development it is necessary to conduct the planned experiment with the use of quality materials. It was established that to increase the strength, chemical additives should be added in to concrete mix, it will let reduce cement amount. Originality. Experiments proved the usage of modern chemical additives in order to improve the properties of concrete. Models were developed, reflecting

  15. THE PECULIARITIES OF DESIGNING OF MONOLITHIC FOUNDATION SLABS IN BANGLADESH

    Directory of Open Access Journals (Sweden)

    Анна Николаевна Малахова

    2017-05-01

    Full Text Available The climatic and engineering-geological conditions of the construction sites for civil buildings in the People's Republic of Bangladesh are considered. There are described the features of the constructive solution of load-bearing structures of buildings of mass urban development. Monolithic reinforced concrete buildings of medium height of column and wall construction systems are considered, and the average ground pressure is determined. There are shown the slabs foundations of such buildings, the features of their design and reinforcement, including under the conditions of seismic influences.

  16. Surfaces and slabs of fractional topological insulator heterostructures

    Science.gov (United States)

    Sahoo, Sharmistha; Sirota, Alexander; Cho, Gil Young; Teo, Jeffrey C. Y.

    2017-10-01

    Fractional topological insulators (FTIs) are electronic topological phases in (3 +1 ) dimensions enriched by time reversal (TR) and charge U (1 ) conservation symmetries. We focus on the simplest series of fermionic FTIs, whose bulk quasiparticles consist of deconfined partons that carry fractional electric charges in integral units of e*=e /(2 n +1 ) and couple to a discrete Z2 n +1 gauge theory. We propose massive symmetry preserving or breaking FTI surface states. Combining the long-ranged entangled bulk with these topological surface states, we deduce the novel topological order of quasi-(2 +1 ) -dimensional FTI slabs as well as their corresponding edge conformal field theories.

  17. Effect of Rotation in an Orthotropic Elastic Slab

    Directory of Open Access Journals (Sweden)

    Santra S.

    2017-02-01

    Full Text Available The fundamental equations of the two dimensional generalized thermoelasticity (L-S model with one relaxation time parameter in orthotropic elastic slab has been considered under effect of rotation. The normal mode analysis is used to the basic equations of motion and heat conduction equation. Finally, the resulting equations are written in the form of a vector-matrix differential equation which is then solved by the eigenvalue approach. The field variables in the space time domain are obtained numerically. The results corresponding to the cases of conventional thermoelasticity CTE, extended thermoelasticity (ETE and temperature rate dependent thermoelasticity (TRDTE are compared by means of graphs.

  18. Contact Loss beneath Track Slab Caused by Deteriorated Cement Emulsified Asphalt Mortar: Dynamic Characteristics of Vehicle-Slab Track System and Prototype Experiment

    OpenAIRE

    Liu, Dan; Liu, Yu-feng; Ren, Juan-juan; Yang, Rong-shan; Liu, Xue-yi

    2016-01-01

    The contact loss beneath track slab caused by deteriorated cement emulsified asphalt mortar (CA mortar) has been one of the main diseases occurring in the CRTS- (China Railway Track System-) I Slab Track of high-speed railway in China. Based on the slab track design theory and the vehicle-track coupling vibration theory, a vehicle-track vertical coupling dynamic FEM model was established to analyze the influence of the contact loss length on the dynamic characteristics of vehicle and track su...

  19. Broadband availability in metropolitan and non-metropolitan Pennsylvania

    Directory of Open Access Journals (Sweden)

    Lawrence E. Wood

    2016-09-01

    Full Text Available Over the past few years having a broadband connection has become essential for many Internet activities. As broadband increases in importance, it becomes imperative to assess how its use and availability may vary, especially in relation to issues such as geographic location. For rural areas in particular, the availability of broadband service is especially important. This research assesses broadband service availability in rural areas of Pennsylvania, USA. In particular, it examines the extent to which Digital Subscriber Line (DSL and broadband cable modem services are being deployed throughout rural Pennsylvania. It compares this deployment with the availability of such services in the state’s urban and metropolitan areas. The results of this research suggest that there is a “digital divide” in terms of broadband availability between rural and urban areas of Pennsylvania. However, this “divide” is perhaps not as wide as might be expected. Thus, as broadband is becoming increasingly available in rural areas of the U.S. and throughout much of the rest of the world, this research concludes that while research must remain vigilant in terms of assessing advanced telecommunications availability in rural areas, future research should also be sure to focus on how such technologies can be used to promote economic and social concerns, including in relation to building online networks and diminishing social and professional isolation in rural areas.

  20. Metropolitan area networks: a corner stone in the broadband era

    Science.gov (United States)

    Ghanem, Adel

    1991-02-01

    Deployment of Broadband ISDN is being influenced by both a market pull and a technology push. New broadband service opportunities exist in the business and residential sectors of the market place. It is envisioned that some customers will need connections directly to broadband switches because of the high bandwidth needed for their applications. At the same time Metropolitan Area Network (MAN) systems will serve those customers with bandwidth requirements less than or equal to 150 Mbps. A given MAN will have a geographical domain to serve where it will carry out the switching tasks within this domain. While MANs couldbe designed using differentarchitecturalconcepts the setofservices expected tobeprovidedby MANs could be equivalent to thelist ofservices thatwillbe supported by the targetbroadband network. This paperpositions MANs as a major building block for Broadband networks. It also examines the evolution process ofMANs as a needed step to assure the successful deployment of these new broadband services. 2. BISDN - OVERVIEW Broadband ISDN (BISDN) is being driven into existence by both a market pull as well as a technology push. Opportunities for new valueadded services are the prime market pull for future broadband networks. These services opportunities extend beyond simple voice and low speed data applications and cover both the residential and the business sectors of the market. It is noted for instance that business customers have growing needs for sophisticated telecommunication vehicles to support their

  1. Convective instability of stagnant slabs at the base of the Mantle Transition Zone

    Science.gov (United States)

    Motoki, M.; Ballmer, M. D.

    2013-12-01

    Seismic tomography reveals that subducting slabs descend to a depth of about 660 km to stagnate at the base of the mantle transition zone for long timescales. Most of the slab is composed of harzburgite covered by veneers of eclogite and hydrated mantle, a make-up that is positively buoyant overall. Initially, this positive compositional buoyancy is overwhelmed by the negative thermal buoyancy of the cool slab. However, the plate continues to be heated from above and below while it stagnates. Consequently, its thermal buoyancy is expected to slowly increase, turning an initially stable into an unstable thermochemical density stratification, and triggering convective instability. Plumes rising out of stagnating slabs may enhance the transition zone and asthenosphere with compositional heterogeneity, including water, as well as support decompression melting. To study these important processes, we systematically explore the parameters controlling convective instability of stagnating slabs in two-dimensional thermochemical geodynamic models. Preliminary results show that instability occurs at about 50-75 Myr after subduction, a timescale that increases with the age and speed of the subducting plate, as well as Rayleigh number. This timescale is further found to be sensitive to preexisting heterogeneity within the slab, as well as the occurrence of small-scale convection at the base of the overriding plate. The plumes rising out of the slab can deliver only a small fraction of the slab's eclogite to the transition zone, but a larger fraction of the slab's harzburgite and hydrated mantle to the base of the lithosphere, where hydrated lithologies undergo decompression melting in a subset of our models. Most of the slab's eclogite instead settles at the very base of the transition zone. These findings have important implications for the fate of subducted slabs, material transport across the transition zone, the compositional stratification of the mantle as a whole, as well

  2. Experimental and finite element study of ultimate strength of continuous composite concrete slabs with steel decking

    Science.gov (United States)

    Gholamhoseini, Alireza

    2018-02-01

    Composite one-way concrete slabs with profiled steel decking as permanent formwork are commonly used in the construction industry. The steel decking supports the wet concrete of a cast in situ reinforced or post-tensioned concrete slab and, after the concrete sets, acts as external reinforcement. In this type of slab, longitudinal shear failure between the concrete and the steel decking is the most common type of failure at the ultimate load stage. Design codes require the experimental evaluation of the ultimate load capacity and longitudinal shear strength of each type of steel decking using full-scale tests on simple-span slabs. There is also no procedure in current design codes to evaluate the ultimate load capacity and longitudinal shear strength of continuous composite slabs and this is often assessed experimentally by full-scale tests. This paper presents the results of three full-scale tests up to failure on continuous composite concrete slabs cast with trapezoidal steel decking profile (KF70) that is widely used in Australia. Slab specimens were tested in four-point bending at each span with shear spans of span/4. The longitudinal shear failure of each slab is evaluated and the measured mid-span deflection, the end slip and the mid-span steel and concrete strains are also presented and discussed. Redistribution of bending moment in each slab is presented and discussed. A finite element model is proposed and verified by experimental data using interface element to model the bond properties between steel decking and concrete slab and investigate the ultimate strength of continuous composite concrete slabs.

  3. Experimental and finite element study of ultimate strength of continuous composite concrete slabs with steel decking

    Science.gov (United States)

    Gholamhoseini, Alireza

    2018-03-01

    Composite one-way concrete slabs with profiled steel decking as permanent formwork are commonly used in the construction industry. The steel decking supports the wet concrete of a cast in situ reinforced or post-tensioned concrete slab and, after the concrete sets, acts as external reinforcement. In this type of slab, longitudinal shear failure between the concrete and the steel decking is the most common type of failure at the ultimate load stage. Design codes require the experimental evaluation of the ultimate load capacity and longitudinal shear strength of each type of steel decking using full-scale tests on simple-span slabs. There is also no procedure in current design codes to evaluate the ultimate load capacity and longitudinal shear strength of continuous composite slabs and this is often assessed experimentally by full-scale tests. This paper presents the results of three full-scale tests up to failure on continuous composite concrete slabs cast with trapezoidal steel decking profile (KF70) that is widely used in Australia. Slab specimens were tested in four-point bending at each span with shear spans of span/4. The longitudinal shear failure of each slab is evaluated and the measured mid-span deflection, the end slip and the mid-span steel and concrete strains are also presented and discussed. Redistribution of bending moment in each slab is presented and discussed. A finite element model is proposed and verified by experimental data using interface element to model the bond properties between steel decking and concrete slab and investigate the ultimate strength of continuous composite concrete slabs.

  4. IMPROVING THE EFFICIENCY OF MINERAL WOOL SLABS TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Perfilov Vladimir Aleksandrovich

    2016-03-01

    Full Text Available The use of thermal insulation materials is an effective method to create an insulating envelope of a building, as well as to reduce energy costs and increase the durability of building structures. The properties of stone wool products and their operational durability is largely determined by the conditions of formation of the mineral wool carpet, uniform distribution of binder and its curing and the heat treatment conditions. Most domestic technologies are aimed at the production of mineral wool products with volume-oriented structure, which is formed using special units: spreader and corrugator placed in a production line. The next step to obtain the optimum structures is the production of dual density slabs. The denser upper layer receives mechanical loads caused by the operating conditions; the lower, less dense, but more thick layer performs the main function - insulation. The dual density slabs are produced on standard lines supplemented with a special unit, which is located in front of the heat treatment camera. Optimization of heat treatment parameters and prediction of the properties of materials is performed using software package.

  5. Slab waveguide photobioreactors for microalgae based biofuel production.

    Science.gov (United States)

    Jung, Erica Eunjung; Kalontarov, Michael; Doud, Devin F R; Ooms, Matthew D; Angenent, Largus T; Sinton, David; Erickson, David

    2012-10-07

    Microalgae are a promising feedstock for sustainable biofuel production. At present, however, there are a number of challenges that limit the economic viability of the process. Two of the major challenges are the non-uniform distribution of light in photobioreactors and the inefficiencies associated with traditional biomass processing. To address the latter limitation, a number of studies have demonstrated organisms that directly secrete fuels without requiring organism harvesting. In this paper, we demonstrate a novel optofluidic photobioreactor that can help address the light distribution challenge while being compatible with these chemical secreting organisms. Our approach is based on light delivery to surface bound photosynthetic organisms through the evanescent field of an optically excited slab waveguide. In addition to characterizing organism growth-rates in the system, we also show here, for the first time, that the photon usage efficiency of evanescent field illumination is comparable to the direct illumination used in traditional photobioreactors. We also show that the stackable nature of the slab waveguide approach could yield a 12-fold improvement in the volumetric productivity.

  6. Self-avoiding walks in a slab: rigorous results

    International Nuclear Information System (INIS)

    Rensburg, E J Janse van; Orlandini, E; Whittingon, S G

    2006-01-01

    A polymer in the confined spaces between colloid particles loses entropy and exerts a repulsive entropic force on the confining particles. This situation can be modelled by a self-avoiding walk confined in a slab between two parallel planes in the lattice. In this paper, we prove the existence of a limiting free energy for the general case that the walk is interacting with the parallel bounding planes. We also prove that the limiting free energy is strictly increasing with the distance between the bounding planes in some regions of the phase diagram. These results demonstrate the presence of a non-zero repulsive entropic force in the model. Finally, we also examine the relation between the limiting free energy in this model and the limiting free energy in a model of walks adsorbing onto a single plane. We prove that these limiting free energies are equal in some regions of the phase diagram in the limit that the width of the slab between the parallel bounding planes is taken to infinity

  7. Optimal spacing and penetration of cracks in a shrinking slab.

    Science.gov (United States)

    Jenkins, D R

    2005-05-01

    A method based on energy minimization is used to determine the spacing and penetration of a regular array of cracks in a slab that is shrinking due to a changing temperature field. The results show a range of different crack propagation behavior dependent on a single dimensionless parameter, being the ratio of the slab thickness and a characteristic length for the material. At low parameter values the minimum energy state can be achieved by continually adding more cracks until a steady state is achieved. At higher values, a minimum crack spacing is reached at finite time, beyond which the cracks are constrained to propagate with the minimum spacing. In the latter case, the uniform propagation is potentially unstable to a spatial period doubling, leading to increasingly complex crack penetration patterns. The energy minimization combined with the period doubling instability provides a means of determining the minimum energy state of cracks for all time. The problem considered here can be seen as a paradigm for cracking phenomena that occur on a large range of scales, from planetary to microscopic.

  8. MODELING OF TRANSIENT HEAT TRANSFER IN FOAMED CONCRETE SLAB

    Directory of Open Access Journals (Sweden)

    MD AZREE OTHUMAN MYDIN

    2013-06-01

    Full Text Available This paper reports the basis of one-dimensional Finite Difference method to obtain thermal properties of foamed concrete in order to solve transient heat conduction problems in multi-layer panels. In addition, this paper also incorporates the implementation of the method and the validation of thermal properties model of foamed concrete. A one-dimensional finite difference heat conduction programme has been developed to envisage the temperature development through the thickness of the foamed concrete slab, based on an initial estimate of the thermal conductivity-temperature relationship as a function of porosity and radiation within the voids. The accuracy of the model was evaluated by comparing predicted and experimental temperature profiles obtained from small scale heat transfer test on foamed concrete slabs, so that the temperature history of the specimen calculated by the programme closely matches those recorded during the experiment. Using the thermal properties of foamed concrete, the validated heat transfer program predicts foamed concrete temperatures in close agreement with experimental results obtained from a number of high temperature tests. The proposed numerical and thermal properties are simple yet efficient and can be utilised to aid manufacturers to develop their products without having to conduct numerous large-scale fire tests.

  9. Broadband mid-infrared and THz chemical detection with quantum cascade laser multi-heterodyne spectrometers (Conference Presentation)

    Science.gov (United States)

    Westberg, Jonas; Sterczewski, Lukasz A.; Patrick, Link; Wysocki, Gerard

    2017-05-01

    Majority of chemical species of interest in security and safety applications (e.g. explosives) have complex molecular structures that produce unresolved rotational-vibrational spectroscopic signatures in the mid-infrared. This requires spectroscopic techniques that can provide broadband coverage in the mid-IR region to target broadband absorbers and high resolution to address small molecules that exhibit well-resolved spectral lines. On the other hand, many broadband mid-IR absorbers exhibit well-resolved rotational components in the THz spectral region. Thus, development of spectroscopic sensing technologies that can address both spectral regions is of great importance. Here we demonstrate recent progress towards broadband high-resolution spectroscopic sensing applications with Fabry-Perot quantum cascade lasers (QCLs) and frequency combs using multi-heterodyne spectroscopy (MHS) techniques. In this paper, we will present spectroscopic sensing of large and small molecules in the mid-IR region using QCLs operating at 8.5µm. An example high-resolution, broadband MHS of ammonia (small molecule) and isobutane (broadband absorber) at atmospheric pressure in the 1165-1190 cm^-1 range will be discussed. We have developed a balanced MHS system for mitigation of the laser intensity fluctuations. Absorption spectroscopy as well as dispersion spectroscopy with minimum fractional absorption down to 10^-4/Hz1/2 and fast spectral acquisition capabilities down to 10 µs/spectrum range will be demonstrated. In order to mitigate the shortcomings of the limited chemical selectivity in the mid-IR, THz QCL based spectrometer is currently under development to provide spectral de-congestion and thus significantly improve chemical identification. Preliminary characterization of the performance of THZ QCL combs for the THz QCL-MHS will be presented.

  10. 78 FR 54241 - Proposed Information Collection; Comment Request; BroadbandMatch Web Site Tool

    Science.gov (United States)

    2013-09-03

    ... Information Collection; Comment Request; BroadbandMatch Web Site Tool AGENCY: National Telecommunications and... goal of increased broadband deployment and use in the United States. The BroadbandMatch Web site began.... Department of Agriculture's Broadband Initiatives Program (BIP) as a tool for potential applicants to...

  11. 76 FR 23812 - Reliability and Continuity of Communications Networks, Including Broadband Technologies; Effects...

    Science.gov (United States)

    2011-04-28

    ...] Reliability and Continuity of Communications Networks, Including Broadband Technologies; Effects on Broadband...: Effects on Broadband Communications Networks of Damage or Failure of Network Equipment or Severe Overload... Docket 10-92 (Effects on Broadband Communications Networks of Damage or Failure of Network Equipment or...

  12. Performance analysis of OFDM modulation on indoor broadband PLC channels

    Science.gov (United States)

    Antonio Cortés, José; Díez, Luis; Cañete, Francisco Javier; Sánchez-Martínez, Juan José; Entrambasaguas, José Tomás

    2011-12-01

    Indoor broadband power-line communications is a suitable technology for home networking applications. In this context, orthogonal frequency-division multiplexing (OFDM) is the most widespread modulation technique. It has recently been adopted by the ITU-T Recommendation G.9960 and is also used by most of the commercial systems, whose number of carriers has gone from about 100 to a few thousands in less than a decade. However, indoor power-line channels are frequency-selective and exhibit periodic time variations. Hence, increasing the number of carriers does not always improves the performance, since it reduces the distortion because of the frequency selectivity, but increases the one caused by the channel time variation. In addition, the long impulse response of power-line channels obliges to use an insufficient cyclic prefix. Increasing its value reduces the distortion, but also the symbol rate. Therefore, there are optimum values for both modulation parameters. This article evaluates the performance of an OFDM system as a function of the number of carriers and the cyclic prefix length, determining their most appropriate values for the indoor power-line scenario. This task must be accomplished by means of time-consuming simulations employing a linear time-varying filtering, since no consensus on a tractable statistical channel model has been reached yet. However, this study presents a simpler procedure in which the distortion because of the frequency selectivity is computed using a time-invariant channel response, and an analytical expression is derived for the one caused by the channel time variation.

  13. Considerations of broadband seismic observation on Mars

    Science.gov (United States)

    Nishikawa, Y.; Kurita, K.; Araya, A.; Hori, T.; Kobayashi, N.; Shiraishi, H.; Kakuma, H.; Ishihara, Y.

    2010-12-01

    The surface of Mars has been extensively investigated and huge amount of data have been acquired such as high Res images. On the other hand interior of the Mars has been only weakly constrained by the mean density, the moment of inertia and gravity data. The size of core is poorly constrained and negatively correlated with the core density. High dissipation state is reported for the mantle by tidal interaction (Bills et al 2006), which is against a conventional view of small,cool planet. To clarify these points seismic observation on Mars is deadly needed. Japan Mars exploration project(MELOS) is now under discussion and it includes seismic measurements for determination the interior structure of Mars such as the core size, its state and attenuation in the mantle. Our plan is to install broadband high sensitivity seismometers,which are intended to detect continuous excitation of free oscillation by atmospheric turbulence. In this presentation we would like to show a basic design of broadband high sensitivity seismometer as well as environment protection designs. The basic parts are composed of a long period pendulum, laser interferometry and its control feedback electricity. As for the environment protection design,the following factors are important. 1. Surface condition. Martian surface is composed of stones gravels and sand. Drift is expected to occur due to the sudden change in ground slope. We need a device for self adjustment to keep the horizontal. 2. Temperature. Surface temperature at Martian equator is expected to vary between 190 to 300K. We have to consider changes in spring tension, thermal expansion of components and changes in circuit constants. 3. Surface wind. Inhomogeneously heated surface and topographic effect generate wind over 20m per second. We have to consider to lessen the effect of seismometer,even if we install the seismometer on the ground. 4. Radiation. Radiation that rains down on Mars is stronger because of thin atmosphere. Radiation

  14. Slab track field test and demonstration program for shared freight and high-speed passenger service

    Science.gov (United States)

    2010-08-01

    Two types of slab tracks were installed on the High Tonnage Loop at the Facility for Accelerated Service Testing. Direct fixation slab track (DFST) and independent dual block track (IDBT) were installed into a 5-degree curve with 4-inch superelevatio...

  15. Finite element analysis, mechanical assessment and material comparison of two volar slab constructs.

    Science.gov (United States)

    Hamilton, Steven W; Aboud, Hussain

    2009-04-01

    In order to help prevent joint stiffness, the injured or postoperative hand is splinted in the intrinsic-plus position. We aimed to determine the strongest type of volar slab construct that would be appropriate in this treatment. Two constructs were compared, a double-ridged and a non-ridged slab. Two materials were used, plaster of Paris (POP) and resin. We performed finite element analysis (FEA) and mechanical assessment to establish which combination of construct and material resulted in the strongest volar slab. We were unable to form ridges on the resin slab, and therefore this construct was not tested. Finite element analysis showed that most stress occurred at the wrist region, where all the slabs failed. The double-ridged POP slab was found to be 5.3 times stronger than the non-ridged POP slab and 1.4 times stronger than the non-ridged resin slab (pslab, we suggest forming two anterior ridges in the plaster.

  16. Accelerated slab replacement using temporary precast panels and self-consolidating concrete.

    Science.gov (United States)

    2016-06-06

    Slab replacement is the main activity in any concrete pavement rehabilitation project. According to a survey of industry and FDOT, contractor productivity in slab replacements has been very low, ranging between 25 to 50 cu. yds. The low number of sla...

  17. Juan de Fuca slab geometry and its relation to Wadati-Benioff zone seismicity

    Science.gov (United States)

    McCrory, Patricia A.; Blair, J. Luke; Waldhause, Felix; Oppenheimer, David H.

    2012-01-01

    A new model of the subducted Juan de Fuca plate beneath western North America allows first-order correlations between the occurrence of Wadati-Benioff zone earthquakes and slab geometry, temperature, and hydration state. The geo-referenced 3D model, constructed from weighted control points, integrates depth information from earthquake locations and regional seismic velocity studies. We use the model to separate earthquakes that occur in the Cascadia forearc from those that occur within the underlying Juan de Fuca plate and thereby reveal previously obscured details regarding the spatial distribution of earthquakes. Seismicity within the slab is most prevalent where the slab is warped beneath northwestern California and western Washington suggesting that slab flexure, in addition to expected metamorphic dehydration processes, promotes earthquake occurrence within the subducted oceanic plate. Earthquake patterns beneath western Vancouver Island are consistent with slab dehydration processes. Conversely, the lack of slab earthquakes beneath western Oregon is consistent with an anhydrous slab. Double-differenced relocated seismicity resolves a double seismic zone within the slab beneath northwestern California that strongly constrains the location of the plate interface and delineates a cluster of seismicity 10 km above the surface that includes the 1992 M7.1 Mendocino earthquake. We infer that this earthquake ruptured a surface within the Cascadia accretionary margin above the Juan de Fuca plate. We further speculate that this earthquake is associated with a detached fragment of former Farallon plate. Other subsurface tectonic elements within the forearc may have the potential to generate similar damaging earthquakes.

  18. Study of stratified dielectric slab medium structures using pseudo-spectral time domain (PSTD) algorithm

    DEFF Research Database (Denmark)

    Tong, M.S.; Lu, Y.; Chen, Y.

    2005-01-01

    A planar stratified dielectric slab medium, which is an interesting problem in optics and geophysics, is studied using a pseudo-spectral time-domain (PSTD) algorithm. Time domain electric fields and frequency domain propagation characteristics of both single and periodic dielectric slab...

  19. ENGINEERING DESIGN CRITERIA FOR SUB-SLAB DEPRESSURIZATION SYSTEMS IN LOW-PERMEABILTY SOLIDS

    Science.gov (United States)

    The report describes the development of engineering design criteria for the successful design, installation, and operation of sub-slab depressurization systems, based on radon (Rn) mitigation experience on 14 slab-on-grade houses in South Central Florida. The Florida houses are c...

  20. An approximate solution of the two-group critical problem for reflected slabs

    International Nuclear Information System (INIS)

    Ishiguro, Y.; Garcia, R.D.M.

    1977-01-01

    A new approximation is developed to solve two group slab problems involving two media where one of the media is infinite. The method consists in combining the P sub(L) approximation with invariance principles. Several numerical results are reported for the critical slab problem [pt