WorldWideScience

Sample records for brick wall method

  1. [Study on Hollow Brick Wall's Surface Temperature with Infrared Thermal Imaging Method].

    Science.gov (United States)

    Tang, Ming-fang; Yin, Yi-hua

    2015-05-01

    To address the characteristic of uneven surface temperature of hollow brick wall, the present research adopts soft wares of both ThermaCAM P20 and ThermaCAM Reporter to test the application of infrared thermal image technique in measuring surface temperature of hollow brick wall, and further analyzes the thermal characteristics of hollow brick wall, and building material's impact on surface temperature distribution including hollow brick, masonry mortar, and so on. The research selects the construction site of a three-story-high residential, carries out the heat transfer experiment, and further examines the exterior wall constructed by 3 different hollow bricks including sintering shale hollow brick, masonry mortar and brick masonry. Infrared thermal image maps are collected, including 3 kinds of sintering shale hollow brick walls under indoor heating in winter; and temperature data of wall surface, and uniformity and frequency distribution are also collected for comparative analysis between 2 hollow bricks and 2 kinds of mortar masonry. The results show that improving heat preservation of hollow brick aid masonry mortar can effectively improve inner wall surface temperature and indoor thermal environment; non-uniformity of surface temperature decreases from 0. 6 to 0. 4 °C , and surface temperature frequency distribution changes from the asymmetric distribution into a normal distribution under the condition that energy-saving sintering shale hollow brick wall is constructed by thermal mortar replacing cement mortar masonry; frequency of average temperature increases as uniformity of surface temperature increases. This research provides a certain basis for promotion and optimization of hollow brick wall's thermal function.

  2. The "Brick Wall" Graphic Organizer

    Science.gov (United States)

    Matteson, Shirley M.

    2016-01-01

    A brick wall provides a fitting description of what happens when teachers try to teach a concept for which students are unprepared. When students are unsuccessful academically, their foundational knowledge may be missing, incomplete, or incorrect. As a result, students "hit a brick wall," and their academic progress stops because they do…

  3. Entropy of Warped Taub-NUT AdS Black String via the Brick Wall Method

    CERN Document Server

    Lee, Chong Oh

    2014-01-01

    When we consider five-dimensional warped Taub-NUT AdS black string with minimally coupled massive scalar field, we calculate an entropy by using the brick wall method. In extremely light effective mass, we find the entropy is proportional to an extra dimension wave number as well as quadratically divergent in a cutoff parameter. After taking zero NUT charge, we find the entropy of warped (AdS) Schwartzshield black hole string has a similar properties in as warped Taub-NUT AdS black string.

  4. A Study of the Effect of Infilled Brick Walls on Behavior of Eccentrically Braced Frames Using Explicit Finite Elements Method

    Directory of Open Access Journals (Sweden)

    Amir S. Daryan

    2009-01-01

    Full Text Available Problem statement: Eccentrically Braced Frames (EBFs are usually infilled by masonry walls, but in common design, the stiffness and lateral resistance of these walls is ignored. Considering the results of carried out tests and studies, it seems that infilled masonry walls have a significant influence on the stiffness and the strength of EBFs. Since experimental test of total frame with infilled brick wall is a very expensive and time consuming process, proper numerical models which can precisely simulate the behavior of EBFs considering the effects of infilled brick wall are necessary. Approach: In this study, a proper model is made using explicit finite elements method to study the behavior of EBFs with infilled masonry wall. Because of complicated mechanical and geometrical properties of masonry walls and also because of the interaction between steel frame and masonry wall, this model is not easy to obtain. To ensure the ability of the model to precisely simulate the behavior of an EBF with infilled brick wall, initial models were made and the problems were solved comparing the results of experimental test and the results of these initial models. Firstly, material models and some basic principles of explicit finite element algorithm are used and three initial models were made: a model of a brick wall without eccentrically braced steel frame, a model of an EBF without infilled brick wall and finally a model of an EBF with infilled brick wall. Results: Using these three initial models, constitutive model for masonry and steel material and also the proper elements for modeling the behavior of mortar is obtained. Studies showed that good prediction of the behavior of a system consisting of EBF and masonry wall is possible, by minimizing the kinematical energy and using a special time scaling of explicit finite element model. Conclusion: After verifying the finite element models, the influence of masonry infilled wall on the behavior of

  5. Brick Walls on the Brane

    CERN Document Server

    Medved, A J M

    2002-01-01

    The so-called ``brick-wall model'' is a semi-classical approach that has been used to explain black hole entropy in terms of thermal matter fields. Here, we apply the brick-wall formalism to thermal bulk fields in a Randall-Sundrum brane world scenario. In this case, the black hole entity is really a string-like object in the anti-de Sitter bulk, while appearing as a Schwarzchild black hole to observers living on the brane. In spite of these exotic circumstances, we establish that the Bekenstein-Hawking entropy law is preserved. Although a similar calculation was recently considered in the literature, this prior work invoked a simplifying assumption (which we avoid) that can not be adequately justified.

  6. Brick walls on the brane

    Energy Technology Data Exchange (ETDEWEB)

    Medved, A J M [Department of Physics and Theoretical Physics Institute, University of Alberta, Edmonton (Canada)

    2002-01-21

    The so-called 'brick-wall model' is a semiclassical approach that has been used to explain black hole entropy in terms of thermal matter fields. Here, we apply the brick-wall formalism to thermal bulk fields in a Randall-Sundrum brane world scenario. In this case, the black hole entity is really a string-like object in the anti-de Sitter bulk, while appearing as a Schwarzchild black hole to observers living on the brane. In spite of these exotic circumstances, we establish that the Bekenstein-Hawking entropy law is preserved. Although a similar calculation was recently considered in the literature, this prior study invoked a simplifying assumption (which we avoid) that cannot be adequately justified.

  7. Moisture movements in render on brick wall

    DEFF Research Database (Denmark)

    Hansen, Kurt Kielsgaard; Munch, Thomas Astrup; Thorsen, Peter Schjørmann

    2003-01-01

    A three-layer render on brick wall used for building facades is studied in the laboratory. The vertical render surface is held in contact with water for 24 hours simulating driving rain while it is measured with non-destructive X-ray equipment every hour in order to follow the moisture front...... through the render and into the brick. The test specimen is placed between the source and the detector. The test specimens are all scanned before they are exposed to water. In that way the loss of counts from the dry scan to the wet scan qualitatively shows the presence of water. The results show nearly...... no penetration of water through the render and into the brick, and the results are independent of the start condition of the test specimens. Also drying experiments are performed. The results show a small difference in the rate of drying, in favour of the bricks without render....

  8. Brick Walls and AdS/CFT

    CERN Document Server

    Kay, Bernard S

    2011-01-01

    We discuss the relationship between the bulk-boundary correspondence in Rehren's algebraic holography (and in other 'fixed-background' approaches to holography) and in mainstream 'Maldacena AdS/CFT'. Especially, we contrast the understanding of black-hole entropy from the viewpoint of QFT in curved spacetime -- in the framework of 't Hooft's 'brick wall' model -- with the understanding based on Maldacena AdS/CFT. We show that the brick-wall modification of a Klein Gordon field in the Hartle-Hawking-Israel state on 1+2-Schwarzschild AdS (BTZ) has a well-defined boundary limit with the same temperature and entropy as the brick-wall-modified bulk theory. One of our main purposes is to point out a close connection, for general AdS/CFT situations, between the puzzle raised by Arnsdorf and Smolin regarding the relationship between Rehren's algebraic holography and mainstream AdS/CFT and the puzzle embodied in the 'correspondence principle' proposed by Mukohyama and Israel in their work on the brick-wall approach to...

  9. Black hole entropy without brick walls

    OpenAIRE

    Xiang, Li

    2002-01-01

    The properties of the thermal radiation are discussed by using the new equation of state density motivated by the generalized uncertainty relation in the quantum gravity. There is no burst at the last stage of the emission of a Schwarzshild black hole. When the new equation of state density is utilized to investigate the entropy of a scalar field outside the horizon of a static black hole, the divergence appearing in the brick wall model is removed, without any cutoff. The entropy proportiona...

  10. New Bricks in the Wall

    Institute of Scientific and Technical Information of China (English)

    RONG JIAOJIAO

    2007-01-01

    @@ Whenever a newcomer enters the classroom, he points at the wall. "Look at that!" says Li Shunye, indicating a picture of something that looks a bit like a pink furry fox, only with an oversized tail. "It's a squirrel," says the 9-year-old. "I made it."

  11. Modern Solutions to Eliminate Capillarity Moisture from Brick Walls – Comer Method

    Directory of Open Access Journals (Sweden)

    Florin L. Tamaş

    2008-01-01

    Full Text Available The existing stock at this time in our country is, in general, described by the old buildings built before 1990. Their degradation, from waterproofing protection point of view, noticeable by infiltrations of water, both at the level of the superstructure (roof, and the default thermal-hydro isolation and infrastructure (walls, is a result of multiple causes. Some of these causes were: deficient work of hydro isolation, thereby understanding the failure in implementing details, the use of materials with poor technical characteristics or savings regarding use of materials, improperly qualified or unqualified personnel for such activities. Intervention on buildings that have such problems, in order to ensure the requirements and criteria for specific performance of the waterproofing work, should pursue aspects of analysing the current situation, diagnose the causes of infiltrations, determining solutions and how to remedy those works, in order to comply with the specifications of the quality Law 10/1995 and the general requirement of waterproofing isolation.

  12. Black hole entropy without brick walls

    CERN Document Server

    Xiang, L

    2002-01-01

    The properties of the thermal radiation are discussed by using the new equation of state density motivated by the generalized uncertainty relation in the quantum gravity. There is no burst at the last stage of the emission of a Schwarzshild black hole. When the new equation of state density is utilized to investigate the entropy of a scalar field outside the horizon of a static black hole, the divergence appearing in the brick wall model is removed, without any cutoff. The entropy proportional to the horizon area is derived from the contribution of the vicinity of the horizon.

  13. Black hole entropy without brick walls

    Science.gov (United States)

    Xiang, Li

    2002-07-01

    The properties of the thermal radiation are discussed by using the new equation of state density motivated by the generalized uncertainty relation in the quantum gravity. There is no burst at the last stage of the emission of a Schwarzschild black hole. When the new equation of state density is utilized to investigate the entropy of a scalar field outside the horizon of a static black hole, the divergence appearing in the brick wall model is removed, without any cutoff. The entropy proportional to the horizon area is derived from the contribution of the vicinity of the horizon.

  14. Brick walls and AdS/CFT

    Science.gov (United States)

    Kay, Bernard S.; Ortíz, L.

    2014-05-01

    We discuss the relationship between the bulk-boundary correspondence in Rehren's algebraic holography (and in other `fixed-background', QFT-based, approaches to holography) and in mainstream string-theoretic `Maldacena AdS/CFT'. Especially, we contrast the understanding of black-hole entropy from the point of view of QFT in curved spacetime—in the framework of 't Hooft's `brick wall' model—with the understanding based on Maldacena AdS/CFT. We show that the brick-wall modification of a Klein-Gordon field in the Hartle-Hawking-Israel state on dimensional Schwarzschild AdS has a well-defined boundary limit with the same temperature and entropy as the brick-wall-modified bulk theory. One of our main purposes is to point out a close connection, for general AdS/CFT situations, between the puzzle raised by Arnsdorf and Smolin regarding the relationship between Rehren's algebraic holography and mainstream AdS/CFT and the puzzle embodied in the `complementarity principle' proposed by Mukohyama and Israel in their work on the brick-wall approach to black hole entropy. Working on the assumption that similar results will hold for bulk QFT other than the Klein-Gordon field and for Schwarzschild AdS in other dimensions, and recalling the first author's proposed resolution to the Mukohyama-Israel puzzle based on his `matter-gravity entanglement hypothesis', we argue that, in Maldacena AdS/CFT, the algebra of the boundary CFT is isomorphic only to a proper subalgebra of the bulk algebra, albeit (at non-zero temperature) the (GNS) Hilbert spaces of bulk and boundary theories are still the `same'—the total bulk state being pure, while the boundary state is mixed (thermal). We also argue from the finiteness of its boundary (and hence, on our assumptions, also bulk) entropy at finite temperature, that the Rehren dual of the Maldacena boundary CFT cannot itself be a QFT and must, instead, presumably be something like a string theory.

  15. The Heat Transfer Coefficient of Recycled Concrete Bricks Combination with EPS Insulation Board Wall

    Directory of Open Access Journals (Sweden)

    Jianhua Li

    2015-01-01

    Full Text Available Four tectonic forms samples were conducted to test their heat transfer coefficients. By analyzing and comparing the test values and theoretical values of the heat transfer coefficient, a corrected-value calculation method for determining the heat transfer coefficient was proposed; the proposed method was proved to be reasonably correct. The results indicated that the recycled concrete brick wall heat transfer coefficient is higher than that of the clay brick wall, the heat transfer coefficient of recycled concrete brick wall could be effectively reduced when combined with the EPS insulation board, and the sandwich insulation type was better than that of external thermal insulation type.

  16. Hidden Degeneracy in the Brick Wall Model of Black Holes

    CERN Document Server

    Sen-Gupta, K; Gupta, Kumar S.; Sen, Siddhartha

    2003-01-01

    Quantum field theory in the near-horizon region of a black hole predicts the existence of an infinite number of degenerate modes. Such a degeneracy is regulated in the brick wall model by the introduction of a short distance cutoff. In this Letter we show that states of the brick wall model with non zero energy admit a further degeneracy for any given finite value of the cutoff. The black hole entropy is calculated within the brick wall model taking this degeneracy into account. Modes with complex frequencies however do not exhibit such a degeneracy.

  17. Not "Just Another Brick in the Wall"

    Science.gov (United States)

    Zolkower, Betina A.; Rubel, Laurie H.

    2015-01-01

    "Low threshold, high ceiling" tasks are accessible to diverse learners; invite a wide range of approaches; and hold the potential to further challenge, strengthen, and extend everyone's mathematical reasoning. In this article, the authors present a family of Brick Pyramid problems as examples of "low threshold, high ceiling"…

  18. "Method, system and storage medium for generating virtual brick models"

    DEFF Research Database (Denmark)

    2009-01-01

    An exemplary embodiment is a method for generating a virtual brick model. The virtual brick models are generated by users and uploaded to a centralized host system. Users can build virtual models themselves or download and edit another user's virtual brick models while retaining the identity...... of the original virtual brick model. Routines are provided for both storing user created building steps in and generating automated building instructions for virtual brick models, generating a bill of materials for a virtual brick model and ordering physical bricks corresponding to a virtual brick model....

  19. An Improved Thin Film Brick-Wall Model of Black Hole Entropy

    Institute of Scientific and Technical Information of China (English)

    LIU Wen-Biao; ZHAO Zheng

    2001-01-01

    We improve the brick-wall model to take only the contribution of a thin film near the event horizon into account. This improvement not only gives us a satisfactory result, but also avoids some drawbacks in the original brick wall method such as the little mass approximation, neglecting logarithm term, and taking the term L3 as the contribution of the vacuum surrounding a black hole. It is found that there is an intrinsic relation between the event horizon and the entropy. The event horizon is the characteristic of a black hole, so the entropy calculating of a black hole is also naturally related to its horizon.

  20. Measure Guideline. Installing Rigid Foam Insulation on the Interior of Existing Brick Walls

    Energy Technology Data Exchange (ETDEWEB)

    Natarajan, Hariharan [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Klocke, Steve [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Puttagunta, Srikanth [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2012-06-01

    This measure guideline provides information on an effective method to insulate the interior of existing brick masonry walls with extruded polystyrene (XPS) insulation board. The guide outlines step-by-step design and installation procedures while explaining the benefits and tradeoffs where applicable. The authors intend that this document be useful to a varied audience that includes builders,remodelers, contractors and homeowners.

  1. Measure Guideline: Installing Rigid Foam Insulation on the Interior of Existing Brick Walls

    Energy Technology Data Exchange (ETDEWEB)

    Natarajan, H.; Klocke, S.; Puttagunta, S.

    2012-06-01

    This measure guideline provides information on an effective method to insulate the interior of existing brick masonry walls with extruded polystyrene (XPS) insulation board. The guide outlines step-by-step design and installation procedures while explaining the benefits and tradeoffs where applicable. The authors intend that this document be useful to a varied audience that includes builders, remodelers, contractors and homeowners.

  2. Horowitz-Strominger Black Hole Entropy Without Brick Wall

    Institute of Scientific and Technical Information of China (English)

    ZHANG Li-Chun; ZHAO Ren; LIN Hai

    2004-01-01

    @@ A Horowitz-Strominger black hole is discussed through a new equation of state density motivated by the generalized uncertainty relation in quantum gravity. There is no burst in the last stage of emission from a HorowitzStrominger black hole. When the new equation of state density is used to investigate the entropy of bosonic field and fermionic field outside the horizon of a static Horowitz-Strominger black hole, the divergence that appears in the brick-wall model is removed without any cutoff. The entropy proportional to the horizon area is derived from the contribution in the vicinity of the horizon.

  3. Spherically symmetric black-hole entropy without brick walls

    Science.gov (United States)

    Ren, Zhao; Yue-Qin, Wu; Li-Chun, Zhang

    2003-11-01

    Properties of the thermal radiation of black holes are discussed using a new equation of state density motivated by the generalized uncertainty relation in quantum gravity. There is no burst at the last stage of emission from a spherically symmetric black hole. When the new equation of state density is used to investigate the entropy of a bosonic field and fermionic field outside the horizon of a static spherically symmetric black hole, the divergence that appears in the brick-wall model is removed without any cutoff. The entropy proportional to the horizon area is derived from the contribution from the vicinity of the horizon.

  4. Letter: Dilatonic Black Hole Entropy Without Brick Walls

    Science.gov (United States)

    Ren, Zhao; Sheng-Li, Zhang

    2004-09-01

    The properties of the thermal radiation are discussed by using the new equation of state density motivated by the generalized uncertainty relation in the quantum gravity. There is no burst at the last stage of the emission of dilatonic black hole. When the new equation of state density is utilized to investigate the entropy of a bosonic field and fermionic field outside the horizon of a static dilatonic black hole, the divergence appearing in the brick wall model is removed, without any cutoff. It is derived from the contribution of the vicinity of the horizon that the entropy is proportional to the horizon area.

  5. Brick walls for black holes in AdS/CFT

    Science.gov (United States)

    Iizuka, Norihiro; Terashima, Seiji

    2015-06-01

    We study the 't Hooft's brick wall model for black holes in a holographic context. The brick wall model suggests that without an appropriate near horizon IR cut-off, the free energy of the probe fields shows the divergence due to the large degenerate states near the horizons. After studying the universal nature of the divergence in various holographic settings in various dimensions, we interpret the nature of the divergence in a holographic context. The free energy divergence is due to the large degeneracy and continuity of the low energy spectrum in the boundary theory at the deconfinement phase. These divergence and continuity should be removed by finite N effects, which make the spectrum discrete even at the deconfinement phase. On the other hand, in the bulk, these degenerate states are localized near the horizon, and the universal divergence of these degenerate states implies that the naive counting of the degrees of freedom in bulk should be modified once we take into account the non-perturbative quantum gravity effects near the horizon. Depending on the microscopic degrees of freedom, the position, where the effective field theory description to count the states breaks down, has different Planck scale dependence. It also implies the difficulty to have an electron like gauge-singlet elementary field in the boundary theory Lagrangian. These singlet fields are at most composite fields, because they show divergent free energy, suggesting a positive power of N at the deconfinement phase.

  6. Brick walls for black holes in AdS/CFT

    Directory of Open Access Journals (Sweden)

    Norihiro Iizuka

    2015-06-01

    Full Text Available We study the 't Hooft's brick wall model for black holes in a holographic context. The brick wall model suggests that without an appropriate near horizon IR cut-off, the free energy of the probe fields shows the divergence due to the large degenerate states near the horizons. After studying the universal nature of the divergence in various holographic settings in various dimensions, we interpret the nature of the divergence in a holographic context. The free energy divergence is due to the large degeneracy and continuity of the low energy spectrum in the boundary theory at the deconfinement phase. These divergence and continuity should be removed by finite N effects, which make the spectrum discrete even at the deconfinement phase. On the other hand, in the bulk, these degenerate states are localized near the horizon, and the universal divergence of these degenerate states implies that the naive counting of the degrees of freedom in bulk should be modified once we take into account the non-perturbative quantum gravity effects near the horizon. Depending on the microscopic degrees of freedom, the position, where the effective field theory description to count the states breaks down, has different Planck scale dependence. It also implies the difficulty to have an electron like gauge-singlet elementary field in the boundary theory Lagrangian. These singlet fields are at most composite fields, because they show divergent free energy, suggesting a positive power of N at the deconfinement phase.

  7. Reissner-Nordstrom Black Hole Entropy Inside and Outside the Brick Wall

    Institute of Scientific and Technical Information of China (English)

    刘文彪

    2003-01-01

    Applying the generalized uncertainty relation to the calculation of the free energy and entropy of a Reissner Nordstrom black hole inside the brick wall, the entropy proportional to the horizon area is derived from the contribution of the vicinity of the horizon. This is compared with the entropy calculated via the original brick wall model. The entropy given by the original brick wall model comes from the outside of the brick wall seemingly.The inside result using generalized uncertainty relation is similar to the outside result using original uncertainty relation, and the divergence inside the brick wall disappears. It is apparent that the cutoff is something related to the quantum theory of gravity.

  8. Decay patterns of brick wall in atmospheric environment: a possible analogue to rock weathering?

    Science.gov (United States)

    Prikryl, Richard; Weishauptová, Zuzana; Přikrylová, Jiřina; Jablonský, Jakub

    2015-04-01

    This study is focused on the decay of bricks exposed in enclosing wall of the Regional maternal hospital in Prague city centre (Czech Republic). The hospital, listed as a Czech architectural monument, has been constructed from locally produced bricks in neo-Gothic style in the period of 1867-1875. The bricks of the enclosing wall show sequence of decay patterns that resemble weathering forms observable on monuments built of natural stone. This study aims to study the observed decay patterns by means of in situ mapping and by analyses of decayed material (optical microscopy, SEM/EDS, X-ray diffraction, Hg-porosimetry, water soluble salts analysis) and to interpret them based on the phase composition and other properties of bricks. Finally, the decay patterns of studied brick wall are compared to known weathering sequences on porous rocks (both on natural outcrops and on artistic monuments).

  9. Steady state theoretical model of fired clay hollow bricks for enhanced external wall thermal insulation

    Energy Technology Data Exchange (ETDEWEB)

    Bouchair, Ammar [Laboratoire de Recherche Cadre Bati et Environnement, Departement d' Architecture, Faculte des Sciences de l' Ingenieur, Universite de Jijel, BP 98 Ouled Aissa, Jijel 18000 (Algeria)

    2008-10-15

    This paper proposes a theoretical model to study the steady state thermal behavior of fired clay hollow bricks for enhanced external wall thermal insulation. The study aims at the development of new materials and structural components with good thermal material properties, with respect to energy saving and ecological design. Thermal insulation capacity of two external walls of different thicknesses, constructed of locally produced bricks, is studied. The basic brick units used for the investigation are small-size bricks with eight equal cavities or recesses and big-size bricks with twelve equal recesses. Their recesses configuration has been varied to perform the assessment. The insulation materials injected within brick recesses during the assessment are granulated cork and expanded polystyrene. The improvement in the thermal performance of the walls will be the result of optimization among the various factors such as brick cavity configurations, integration of insulation within brick recesses and the cavity surface emissivities. So emphasis is given to the study of the impact of these factors singly or in combination on the overall thermal resistance of walls in order to find out the best design solutions to maximize their thermal insulation capacity. Computer modeling and calculations performed, for steady state conditions, show that the increase in hollow brick cavity height contributes to the improvement of the overall thermal resistance of the order of 18-20%. The improvement could significantly increase to the range of 88.64% and 93.33%, if the bricks used are injected with the insulating material. If the cavity surface emissivities are lowered to 0.3, the improvement will be 72.73-78.33%. The results have also shown that replacing the cork by expanded polystyrene (EPS), having lower thermal conductivity, would not improve significantly the overall thermal resistance. This improvement is 9.08% for a wall of small-size bricks having configuration BS2CV and 8

  10. Minimal Length Effects on Entanglement Entropy of Spherically Symmetric Black Holes in Brick Wall Model

    CERN Document Server

    Wang, Peng; Ying, Shuxuan

    2015-01-01

    We compute the black hole horizon entanglement entropy for a massless scalar field in the brick wall model by incorporating the minimal length. Taking the minimal length effects on the occupation number $n(\\omega,l)$ and the Hawking temperature into consideration, we obtain the leading UV divergent term and the subleading logarithmic term in the entropy. The leading divergent term scales with the horizon area. The subleading logarithmic term is the same as that in the usual brick wall model without the minimal length.

  11. Assessment of the mechanical properties of brick masonry by a flat-jack method

    Directory of Open Access Journals (Sweden)

    S.V. Zubkov

    2015-12-01

    Full Text Available The modern Russian methods for defining the mechanical characteristics of brick masonry are based on finding the strength of masonry components (brick and mortar. After getting the results of laboratory tests of components, mechanical characteristics of masonry are calculated using empirical formulae. Those formulae, however, cannot take into consideration the presence of damages and other factors. Obtaining the characteristics (strength and deformation by a direct flat-jack test of masonry fragments on-site looks promising. A widespread use of FEM requires setting accurate deformation features for modeling domes, arches and thin brick outside layer in multilayer walls. Also accurate deformation characteristics are used for calculating temperature loads. The paper gives the results of practical use for the masonry deformation research by the flat-jack test method. The correlation factors are defined and rigidness coefficients of flat-jacks are obtained in the study.

  12. Tunable Gas Permeability of Polymer-Clay Nano Brick Wall Thin Film Assemblies

    Science.gov (United States)

    Gamboa, Daniel; Priolo, Morgan; Grunlan, Jaime

    2010-03-01

    Thin films of anionic natural montmorrilonite (MMT) clay and cationic polyethylenimine (PEI) have been produced by alternately dipping a plastic substrate into dilute aqueous mixtures containing each ingredient. After 40 polymer-clay layers have been deposited, the resulting transparent film exhibits an oxygen transmission rate (OTR) below 0.35 cm^3/m^2 . day when the pH of PEI solution is 10. This low permeability is due to a brick wall nanostructure comprised of completely exfoliated clay bricks in polymeric mortar. This brick wall creates an extremely tortuous path at thicknesses below 250 nm and clay concentration above 80 wt%. A 70-bilayer PEI-MMT assembly has an undetectable OTR (packaging and foil replacement for food.

  13. Brick Wall Model and the Spectrum of a Schwarzschild Black Hole

    Institute of Scientific and Technical Information of China (English)

    LI Xiang; ZHAO Zheng

    2006-01-01

    @@ The quantum entropy of a scalar field near a Schwarzschild black hole is investigated by employing the brick-wall model in the grand canonical ensemble. A positive chemical potential is introduced if the cutoff is set to be of order of the Planck length. We also discuss the relation between the chemical potential and the mass quantum of the black hole.

  14. The quantitative estimation of the vulnerability of brick and concrete wall impacted by an experimental boulder

    Science.gov (United States)

    Zhang, J.; Guo, Z. X.; Wang, D.; Qian, H.

    2016-02-01

    There is little historic data about the vulnerability of damaged elements due to debris flow events in China. Therefore, it is difficult to quantitatively estimate the vulnerable elements suffered by debris flows. This paper is devoted to the research of the vulnerability of brick and concrete walls impacted by debris flows. An experimental boulder (an iron sphere) was applied to be the substitute of debris flow since it can produce similar shape impulse load on elements as debris flow. Several walls made of brick and concrete were constructed in prototype dimensions to physically simulate the damaged structures in debris flows. The maximum impact force was measured, and the damage conditions of the elements (including cracks and displacements) were collected, described and compared. The failure criterion of brick and concrete wall was proposed with reference to the structure characteristics as well as the damage pattern caused by debris flows. The quantitative estimation of the vulnerability of brick and concrete wall was finally established based on fuzzy mathematics and the proposed failure criterion. Momentum, maximum impact force and maximum impact bending moment were compared to be the best candidate for disaster intensity index. The results show that the maximum impact bending moment seems to be most suitable for the disaster intensity index in establishing vulnerability curve and formula.

  15. The prediction of brick wall strengths with artificial neural networks model

    Science.gov (United States)

    Demir, Ali; Kumanlioglu, Ahmet Ali

    2017-01-01

    The aim of this study is to predict with Artificial Neural Networks (ANN) shear strength of brick masonry walls. Shear strength of the walls is determined with diagonal shear tests. It is very difficult to determine strengths of brick masonry walls with experimental procedures. Therefore, an Artificial Neural Networks model is developed with data obtained by investigating many papers from literature and experiments carried out by the authors. Finally, a good degree of coherency is obtained between the experimental and predicted data. The model that is developed makes it possible to easily predict shear strength of the masonry walls. Additionally, this model can be continuously trained with new data and its applicability range can easily be expanded.

  16. Modelling Australian Red Brick and Bluestone Walls in VAPO

    Science.gov (United States)

    2013-01-01

    span. Note that internal masonry walls are also often load bearing for this UNCLASSIFIED 9 UNCLASSIFIED DSTO-TN-1155 type of floor/ ceiling slab ...compressive strength of a short column of masonry material that is mortared together in a manner representative of the wall construction. The bulk...beneath the load bearing wall on the level below. For a slab consisting of a wood deck on wood joists or concrete deck on open web steel joists, the

  17. Another brick in the cell wall: biosynthesis dependent growth model.

    Science.gov (United States)

    Barbacci, Adelin; Lahaye, Marc; Magnenet, Vincent

    2013-01-01

    Expansive growth of plant cell is conditioned by the cell wall ability to extend irreversibly. This process is possible if (i) a tensile stress is developed in the cell wall due to the coupling effect between turgor pressure and the modulation of its mechanical properties through enzymatic and physicochemical reactions and if (ii) new cell wall elements can be synthesized and assembled to the existing wall. In other words, expansive growth is the result of coupling effects between mechanical, thermal and chemical energy. To have a better understanding of this process, models must describe the interplay between physical or mechanical variable with biological events. In this paper we propose a general unified and theoretical framework to model growth in function of energy forms and their coupling. This framework is based on irreversible thermodynamics. It is then applied to model growth of the internodal cell of Chara corallina modulated by changes in pressure and temperature. The results describe accurately cell growth in term of length increment but also in term of cell pectate biosynthesis and incorporation to the expanding wall. Moreover, the classical growth model based on Lockhart's equation such as the one proposed by Ortega, appears as a particular and restrictive case of the more general growth equation developed in this paper.

  18. Another brick in the cell wall: biosynthesis dependent growth model.

    Directory of Open Access Journals (Sweden)

    Adelin Barbacci

    Full Text Available Expansive growth of plant cell is conditioned by the cell wall ability to extend irreversibly. This process is possible if (i a tensile stress is developed in the cell wall due to the coupling effect between turgor pressure and the modulation of its mechanical properties through enzymatic and physicochemical reactions and if (ii new cell wall elements can be synthesized and assembled to the existing wall. In other words, expansive growth is the result of coupling effects between mechanical, thermal and chemical energy. To have a better understanding of this process, models must describe the interplay between physical or mechanical variable with biological events. In this paper we propose a general unified and theoretical framework to model growth in function of energy forms and their coupling. This framework is based on irreversible thermodynamics. It is then applied to model growth of the internodal cell of Chara corallina modulated by changes in pressure and temperature. The results describe accurately cell growth in term of length increment but also in term of cell pectate biosynthesis and incorporation to the expanding wall. Moreover, the classical growth model based on Lockhart's equation such as the one proposed by Ortega, appears as a particular and restrictive case of the more general growth equation developed in this paper.

  19. Characterization of Bricks Used in the External Casing of Roman Bath Walls "Gadara Jordan".

    Science.gov (United States)

    El Gohary, A. M.; Al Naddaf, M. M.

    The use of sub-soil materials have been used in buildings long time ago, for more than 10,000 years. This study investigates the different characteristics of brick units used in one of the Roman baths in Gadara archaeological site. This is achieved by studying the raw materials and the different technological measurements of brick units: shapes,dimensions and visual description. Moreover, it studies the construction techniques and deterioration problems, by using some scientific techniques and analytical procedures such as EDX for defining the elemental and chemical characteristics of brick samples,Polarizing microscope and XRD for studying the mineralogical components, in addition to the use of SEM that was used for studying the morphological characteristics of the samples. Furthermore, this study determines the different physical, mechanical and thermal properties of the collected samples according to different scientific techniques and standard tools such as digital camera, magnifying glass and mechanical sieves. The results of the study prove that the brick units are divided into two types cubit square and rectangular shapes which are used as external casing layers. They are characterized by homogeneous chemical characteristics and different visual appearances according to the firing degrees and firing conditions (oxidizing or reduction). On the other hand the differences of these physical properties play specific roles in the deterioration cycles,and their mechanisms affect the brick units. Finally, the study provides a definition of the effective methods, materials and preservation measurements for restoring and maintaining the investigated monument.

  20. Detailed Dynamic Heat Transfer in Thick Brick Walls Typical of Lille Metropolis

    Directory of Open Access Journals (Sweden)

    Antczak E.

    2012-10-01

    Full Text Available The study of thermal transfer in old houses massive walls offers a big interest permitting the understanding of their specificities and the choice of a suitable material for their eventual insulation. We propose to study the thermal transfer in massive brick walls that characterize the Northern Europe old houses. To do so, we will begin by defining the thermal transfer mode: we proved that the transfer mode can be reduced to a unidirectional transfer. Then, an experimental wall is built and submitted to two different solicitation types (constant temperature in steady state mode and sinusoidal temperature through a wooden insulated box containing a radiator. The interest of these solicitations is to determine the thermal properties of the wall: the steady-state regime permits to determine the thermal resistances of the system when the harmonic regime permits to determine the thermal capacities of the system.

  1. Comparative thermal performance of static sunshade and brick cavity wall for energy efficient building envelope in composite climate

    Directory of Open Access Journals (Sweden)

    Charde Meghana

    2014-01-01

    Full Text Available Energy efficient building technologies can reduce energy consumption in buildings. In present paper effect of designed static sunshade, brick cavity wall with brick projections and their combined effect on indoor air temperature has been analyzed by constructing three test rooms each of habitable dimensions (3.0 m × 4.0 m × 3.0 m and studying hourly temperatures on typical days for one month in summer and winter each. The three rooms have also been simulated using a software and the results have been compared with the experimental results. Designed static sunshade increased indoor air temperature in winter while proposed brick cavity wall with brick projections lowered it in summer. Combined effect of building elements lowered indoor air temperature in summer and increased it in winter as compared to outdoor air temperature. It is thus useful for energy conservation in buildings in composite climate.

  2. Determination of shear parameters of concrete filled head-straight masonry brick walls

    Directory of Open Access Journals (Sweden)

    Reza Amiraslanzadeh

    2015-03-01

    Full Text Available The aim of present study was determination of shear parameters of reinforced and unreinforced masonry brick walls assembled with Head-straight texture order. Experimental tests carried out on triplets in order to define shear parameters of brick mortar interface, and diagonal compression test in order to define shear strength of masonry panels. According to various interpretations on evaluation of shear strength using diagonal compression test, comparison between mentioned values and those obtained by laboratory tests on shear triplets are presented. The results showed that, although the generated internal columns have not been tied together on top and bottom sides, they contributed to a significant improvement on shear resistance of the masonry panels. Referring to the interpretations on test outcomes, it was perceived that the formula which was obtained by adopting the Turnašek- Cacovic criterion is the most suitable and reliable one. It was concluded that filling the voids of Head-straight texture masonry walls using steel fiber concrete, significantly increase these walls shear parameters.

  3. Reissner-Nordström black-hole entropy without brick walls

    Science.gov (United States)

    Ren, Zhao; Shuangqi, Hu

    2004-02-01

    The properties of the thermal radiation are discussed by using the new equation of state density motivated by the generalized uncertainty relation in the quantum gravity. There is no burst at the last stage of the emission of the Reissner-Nordström black hole. When the new equation of state density is utilized to investigate the entropy of a bosonic field and a fermionic field outside the horizon of a static Reissner-Nordström black hole, the divergence appearing in the brick wall model is removed, without any cut-off. The entropy proportional to the horizon area is derived from the contribution of the vicinity of the horizon.

  4. Experimental Study on the Seismic Performance of Recycled Concrete Brick Walls Embedded with Vertical Reinforcement

    Directory of Open Access Journals (Sweden)

    Wanlin Cao

    2014-08-01

    Full Text Available Recycled concrete brick (RCB is manufactured by recycled aggregate processed from discarded concrete blocks arising from the demolishing of existing buildings. This paper presents research on the seismic performance of RCB masonry walls to assess the applicability of RCB for use in rural low-rise constructions. The seismic performance of a masonry wall is closely related to the vertical load applied to the wall. Thus, the compressive performance of RCB masonry was investigated firstly by constructing and testing eighteen RCB masonry compressive specimens with different mortar strengths. The load-bearing capacity, deformation and failure characteristic were analyzed, as well. Then, a quasi-static test was carried out to study the seismic behavior of RCB walls by eight RCB masonry walls subjected to an axial compressive load and a reversed cyclic lateral load. Based on the test results, equations for predicting the compressive strength of RCB masonry and the lateral ultimate strength of an RCB masonry wall were proposed. Experimental values were found to be in good agreement with the predicted values. Meanwhile, finite element analysis (FEA and parametric analysis of the RCB walls were carried out using ABAQUS software. The elastic-plastic deformation characteristics and the lateral load-displacement relations were studied.

  5. Experimental Study on the Seismic Performance of Recycled Concrete Brick Walls Embedded with Vertical Reinforcement

    Science.gov (United States)

    Cao, Wanlin; Zhang, Yongbo; Dong, Hongying; Zhou, Zhongyi; Qiao, Qiyun

    2014-01-01

    Recycled concrete brick (RCB) is manufactured by recycled aggregate processed from discarded concrete blocks arising from the demolishing of existing buildings. This paper presents research on the seismic performance of RCB masonry walls to assess the applicability of RCB for use in rural low-rise constructions. The seismic performance of a masonry wall is closely related to the vertical load applied to the wall. Thus, the compressive performance of RCB masonry was investigated firstly by constructing and testing eighteen RCB masonry compressive specimens with different mortar strengths. The load-bearing capacity, deformation and failure characteristic were analyzed, as well. Then, a quasi-static test was carried out to study the seismic behavior of RCB walls by eight RCB masonry walls subjected to an axial compressive load and a reversed cyclic lateral load. Based on the test results, equations for predicting the compressive strength of RCB masonry and the lateral ultimate strength of an RCB masonry wall were proposed. Experimental values were found to be in good agreement with the predicted values. Meanwhile, finite element analysis (FEA) and parametric analysis of the RCB walls were carried out using ABAQUS software. The elastic-plastic deformation characteristics and the lateral load-displacement relations were studied. PMID:28788170

  6. Comparison between TRM and FRP strengthening systems at preventing buckling failure of brick masonry walls

    Directory of Open Access Journals (Sweden)

    Bernat-Maso, E.

    2016-09-01

    Full Text Available Fibre Reinforced Polymer (FRP and Textile Reinforced Mortar (TRM have been studied, compared and applied to strengthen brick masonry walls. The comparison of their performance against second order bending effects is addressed in this paper for the first time. Experimental and analytical data from previous researches and new analytical data for TRM cases are summarised, ordered and systematically compared to analyse the structural response of strengthened brick masonry walls. The results show a similar performance for both systems in terms of load bearing capacity and in-plane response. However, TRM strengthened cases showed greater lateral deformation than FRP ones.Materiales tipo Fibre Reinforced Polymer (FRP y Textile Reinforced Mortar (TRM han sido estudiados, comparados y aplicados para reforzar muros de fábrica de ladrillo. La comparación de su comportamiento frente a efectos de flexión de segundo orden se abordada en este artículo por primera vez. Datos experimentales y analíticos de investigaciones previas y nuevos datos analíticos para los casos de TRM son resumidos, ordenados y sistemáticamente comparados para analizar la respuesta estructural de los muros de fábrica de ladrillo reforzados. Los resultados muestran un comportamiento similar de los dos sistemas respecto su capacidad de carga y su respuesta en el plano. Los casos reforzados con TRM mostraron desplazamientos laterales superiores a los reforzados con FRP.

  7. Modeling thermal performance of exterior walls retrofitted from insulation and modified laterite based bricks materials

    Science.gov (United States)

    Wati, Elvis; Meukam, Pierre; Damfeu, Jean Claude

    2017-06-01

    Uninsulated concrete block walls commonly found in tropical region have to be retrofitted to save energy. The thickness of insulation layer used can be reduced with the help of modified laterite based bricks layer (with the considerably lower thermal conductivity than that of concrete block layer) during the retrofit building fabrics. The aim of this study is to determine the optimum location and distribution of different materials. The investigation is carried out under steady periodic conditions under the climatic conditions of Garoua in Cameroon using a Simulink model constructed from H-Tools (the library of Simulink models). Results showed that for the continuous air-conditioned space, the best wall configuration from the maximum time lag, minimum decrement factor and peak cooling transmission load perspective, is dividing the insulation layer into two layers and placing one at the exterior surface and the other layer between the two different massive layers with the modified laterite based bricks layer at the interior surface. For intermittent cooling space, the best wall configuration from the minimum energy consumption depends on total insulation thickness. For the total insulation thickness less than 8 cm approximately, the best wall configuration is placing the half layer of insulation material at the interior surface and the other half between the two different massive layers with the modified earthen material at the exterior surface. Results also showed that, the optimum insulation thickness calculated from the yearly cooling transmission (estimated only during the occupied period) and some economic considerations slightly depends on the location of that insulation.

  8. Methods for elimination of dampness in Building walls

    Science.gov (United States)

    Campian, Cristina; Pop, Maria

    2016-06-01

    Dampness elimination in building walls is a very sensitive problem, with high costs. Many methods are used, as: chemical method, electro osmotic method or physical method. The RECON method is a representative and a sustainable method in Romania. Italy has the most radical method from all methods. The technology consists in cutting the brick walls, insertion of a special plastic sheeting and injection of a pre-mixed anti-shrinking mortar.

  9. Process parameter optimization for fly ash brick by Taguchi method

    Energy Technology Data Exchange (ETDEWEB)

    Prabir Kumar Chaulia; Reeta Das [Central Mechanical Engineering Research Institute, Durgapur (India)

    2008-04-15

    This paper presents the results of an experimental investigation carried out to optimize the mix proportions of the fly ash brick by Taguchi method of parameter design. The experiments have been designed using an L9 orthogonal array with four factors and three levels each. Small quantity of cement has been mixed as binding materials. Both cement and the fly ash used are indicated as binding material and water binder ratio has been considered as one of the control factors. So the effects of water/binder ratio, fly ash, coarse sand, and stone dust on the performance characteristic are analyzed using signal-to-noise ratios and mean response data. According to the results, water/binder ratio and stone dust play the significant role on the compressive strength of the brick. Furthermore, the estimated optimum values of the process parameters are corresponding to water/binder ratio of 0.4, fly ash of 39%, coarse sand of 24% and stone dust of 30%. The mean value of optimal strength is predicted as 166.22 kg.cm{sup -2} with a tolerance of 10.97 kg.cm{sup -2}. The confirmatory experimental result obtained for the optimum conditions is 160.17 kg.cm{sup -2}. 13 refs., 3 figs., 7 tabs.

  10. Prefabricated EPS Elements used as Strip Foundation of a Single-family House with a Double Brick Wall

    DEFF Research Database (Denmark)

    Rasmussen, Torben Valdbjørn

    2008-01-01

    A new prefabricated lightweight element was designed for a strip foundation that was demonstrated on site as the base of a single-family house with a double brick wall. The element was placed on a stable surface underneath the top soil layer, just 0.25 m underneath the finished ground surface...

  11. A continuous OSL scanning method for analysis of radiation depth-dose profiles in bricks

    DEFF Research Database (Denmark)

    Bøtter-Jensen, L.; Jungner, H.; Poolton, N.R.J.

    1995-01-01

    This article describes the development of a method for directly measuring radiation depth-dose profiles from brick, tile and porcelain cores, without the need for sample separation techniques. For the brick cores, examples are shown of the profiles generated by artificial irradiation using...

  12. A new method to determine thermophysical properties of PCM-concrete brick

    DEFF Research Database (Denmark)

    Cheng, Rui; Pomianowski, Michal Zbigniew; Wang, Xin

    2013-01-01

    . The equivalent specific heat distributions of 4 wt% and 6 wt% PCM-concrete brick were determined using this method. We found that the accuracy (the relative error of the calculated cp based on the inverse problem and their real values ranges from 10.43% to 19.4%) was acceptable for engineering use......Accurate measurement of thermophysical properties of PCM-concrete brick is very important for simulation and evaluation of its energy saving performance. However, there is currently no effective way to accurately measure thermophysical properties of PCM-concrete brick. First we analyzed...... the shortcomings of using traditional testing methods to measure thermophysical properties of PCM-concrete brick. We then proposed a new method based on the inverse problem, which deals with the measurements of thermal conductivity and specific heat of PCM-concrete brick during the phase change process...

  13. Nozzle Bricks and Well Bricks

    Institute of Scientific and Technical Information of China (English)

    Zhang Xiaohui; Peng Xigao

    2011-01-01

    1 Scope This standard specifies the classification,brand,technical requirements,test methods,inspection rules,marking,packing,transportation,storage,and quality certificate of nozzle bricks and well bricks.This standard is applicable to unfired and fired products.

  14. Influence of Method of Bricklaying with Trowel on Thermal Insulation Property of Hollow Brick Wall%传热方向对空心砌块墙体热工性能的影响

    Institute of Scientific and Technical Information of China (English)

    肖婷; 魏玲

    2014-01-01

    通过对砌块单元的模拟值与实验值的比较,确定了模拟结果的可信度,运用数值计算的方法模拟了24种不同孔洞结构的240 mm×115 mm×90 mm粉煤灰小型空心砌块的耦合传热过程,得出单个空心砌块的当量导热系数值。模拟中考虑沿着砌块长度及宽度方向传热对当量导热系数的影响。结果表明:沿着传热垂直方向增加孔数减弱了砌块的保温隔热效果,沿着传热平行方向增加孔数增强了砌块的保温隔热性能。模拟的结果对粉煤灰小型空心砌块的结构选型、优化设计和建筑的节能与节材具有重要意义。%The reliability of simulation is confirmed by the comparison of the experimental value and simulation value of block unit. The coupled heat transportation process of 240 mm×115 mm×90 mm fly-ash small-sized hollow brick with 24 kinds of configurations with different holes number and arrays was simu-lated, and equivalent thermal conductivity (ETC) of single hollow brick was obtained. Heat transfer along length and width direction to the hollow block is considered in the simulation. The results showed that:with the increase of the holes number in vertical direction of heat transfer, the effect of thermal insulation on hollow bricks is weakened; but with the increase of the holes number in parallel direction of heat trans-fer, the effect of thermal insulation on hollow bricks is enhanced. The results of simulation have signifi-cance for structural form selection, optimal design and energy conservation and materials saving for build-ings.

  15. Galectin-3 in heart failure pathology--"another brick in the wall"?

    Science.gov (United States)

    Lala, Radu I; Puschita, Maria; Darabantiu, Dan; Pilat, Luminita

    2015-06-01

    Heart failure is a disease affecting millions of patients each year, and is responsible for burdening the world with high mortality rates. More concerns come from its numerous hospital readmissions (with an estimated number of 2.6 million per year which makes it one of the leading diseases responsible for national healthcare expenditures). Despite drastic improvement of therapies in recent years, heart failure remains a progressive disease. Thus, more attention has been given to finding potential biomarkers involved in the pathological mechanisms of this disease that would potentially lead to faster diagnosis and improved prognosis. One of the emerging biomarkers that has just recently come into the spotlight is galectin-3. It was associated in recent clinical trials with both the progression and severity of heart failure. Ventricular remodelling and myocardial fibrosis are essential for heart failure development and are linked to poor outcomes. An ever-growing body of evidence places galectin-3 as an important link between inflammation and fibrosis, which play a prominent role in cardiac remodelling.This review sums up the most relevant experimental and clinical studies about galectin-3 and its potential prognostic value in heart failure. The article also provides a better understanding of this molecule's involvement in heart failure pathology by modulating cardiac fibrosis. It also weighs whether the available data on galectin-3 are consistent enough to reduce readmissions and mortality while improving diagnosis and future therapies for heart failure, versus the possibility that it is simply"another brick in the wall?"

  16. Leaching of Heavy Metals Using SPLP Method from Fired Clay Brick Incorporating with Sewage Sludge

    Science.gov (United States)

    Kadir, Aeslina Abdul; Salim, Nurul Salhana Abdul; Amira Sarani, Noor; Aqma Izurin Rahmat, Nur

    2017-05-01

    Sewage sludge is a by-product generate from wastewater treatment process. The sewage sludge contains significant trace metal such as Cr, Mn, Ni, Cu, Zn, As, Cd and Pb which are toxic to the environment. Sewage sludge is disposed of by landfilling method. However, this option not suitable because of land restriction and environmental control regulations imposed. Therefore, sewage sludge from wastewater treatment plant was incorporated into fired clay brick to produce good quality of brick as well as reducing heavy metals from sludge itself. Sewage sludge with 0%, 1%, 5%, 10% and 20% of were incorporated into fired clay bricks and fired at 1050°C temperature with heating rates of 1°C/min. The brick sample then crushed and sieved through 9.5 mm sieve for Synthetic Precipitation Leaching Procedure (SPLP). From the results, incorporation up to 20% of sewage sludge has leached less heavy metals and compliance with USEPA standard.

  17. Control methods for strength of ceramic bricks in the inspection of buildings

    Directory of Open Access Journals (Sweden)

    Ulybin A.V.

    2012-05-01

    Full Text Available The paper brings up the problem of finding the most accurate, reliable and, at the same time, less time-consuming and relatively inexpensive method of determining strength of ceramic bricks. This task is particularly important in the context of the lack of standards governing the use of nondestructive testing methods for ceramic bricks, and the difficulties associated with sampling of ceramic brick masonry for standard tests.In the paper the possibility of determining the compressive strength of corpulent ceramic bricks by testing cylindrical samples taken from the body of masonry, is explored. The relation between standard samples tests results according to GOST standards № 8265-84 and testing of cylindrical samples is given.The experimental results for influence of the direction of kern selection (horizontally and vertically in reference to flat of brick on the strength is presented. The possibility of application of nondestructive testing methods for measuring strength of ceramic bricks is considered. Also the paper includes the examples of field and laboratory experiments.

  18. Basic Deformation Parameters of Solid Clay Bricks and Small Masonry Walls

    Directory of Open Access Journals (Sweden)

    P. Bouška

    2000-01-01

    Full Text Available The basic mechanical properties of clay brick masonry and its components were experimentally investigated in the laboratories of the Klokner Institute. The test specimens of masonry materials and the relevant mechanical properties have been identified in solid clay bricks and cement-lime mortar. The aim of the research activity was to study both the deformability of the prevailing type of clay masonry in the existing buildings, i.e. the masonry made from the solid clay units and the lime-cement mortar, and the most important mechanical properties of masonry components.

  19. Rational preparation of waste coal mixture for production of bricks by the method of compression molding

    Science.gov (United States)

    Stolboushkin, A. Yu; Ivanov, A. I.; Temlyantsev, M. V.; Fomina, O. A.

    2016-10-01

    Rational preparation of the mixture containing technogenic raw material - waste coal for the production of wall ceramics is developed. It was established that the technology of high-quality ceramic bricks requires: grinding of raw materials to class 0.3 + 0 mm, its aggregation in the intensive mixers into granules 1-3 mm, compression molding of adobe to plastic deformation of granules, drying and firing.

  20. Analysis Of Construction Salt Decomposition Within Walls Of Ceramic Brick In The Midtown Tenement Houses

    Directory of Open Access Journals (Sweden)

    Szostak Bartosz

    2015-12-01

    Full Text Available The purpose of this paper is to introduce issues related to the corrosive effects of construction salts. Sequentially, one will discuss issues related to the distribution of salt in the wall, salinity sources and types of masonry material damage. There will also be presented the results of research conducted by the authors, which allowed determining the distribution of salinity in the walls depending on the depth and height of sampling. The paper will present test results of samples taken from several heights and depths within the same piece of wall and summaries from all facilities. Research conducted by the authors were based on chemical analyzes performed using the prepared chemical tests. Assays are made using titration and colorimetric methods.

  1. Archaeometric study of bricks from the ancient defence walls around the town of Pavia in northern Italy

    Directory of Open Access Journals (Sweden)

    Veniale, F.

    2006-09-01

    Full Text Available A study was conducted on bricks sampled from the defense walls around the historic town of Pavia (northern Italy erected during Roman (uncertain and “Spanish”(sixteenth-seventeenth centuries times. An analysis of colour, macro- and micro-chemical composition,mineralogical clusters and structural-textural features showed that similar raw materials were used in the manufacture of these bricks, although certain variations were identified: particle size is finer in Roman bricks, while the “Spanish” version contains ground carbonate and “chamotte” additives. The “Spanish” bricks,fired at lower temperatures, are more porous. The wide range of firing temperatures used to make “Spanish” bricks was very likely related to the intended use. The sporadic presence of maghemite is discussed in the context of the atmosphere prevailing in the kilns. The “Spanish” bricks are lighter in colour as a result of their carbonate content and lower firing temperature. These characteristics, which affect the weather resistance of the different types of brick, should be taken into account in restoration work.Se investigan ladrillos recogidos en las murallas defensivas de la histórica ciudad de Pavía (norte de Italia, que fueron construidas en tiempos romanos (no establecidosy “españoles” (siglos XVI y XVII.En base al color, composición química tanto total como puntual, asociaciones mineralógicas y características texturales,se concluye que se utilizó una materia prima similar en ambas épocas, con algunas particularidades: granulometría más fina en los romanos, adición de carbonato molido y chamota en los “españoles”. Por su parte, la porosidad es mayor en los ladrillos “españoles”. El amplio rango de temperaturas de cocción observado para estos últimos debe estar relacionado con los distintos usos para los cuales fueron destinados. La presencia esporádica de

  2. Rapid radiochemical method for determination of actinides in emergency concrete and brick samples.

    Science.gov (United States)

    Maxwell, Sherrod L; Culligan, Brian K; Kelsey-Wall, Angel; Shaw, Patrick J

    2011-09-02

    A new rapid method for the determination of actinides in emergency concrete and brick samples has been developed at the Savannah River Site Environmental Lab (Aiken, SC, USA) that can be used in emergency response situations or for routine analysis. If a radiological dispersive device (RDD), Improvised Nuclear Device (IND) or nuclear accident occurs, there will be a urgent need for rapid analyses of many different environmental matrices, including building materials such as concrete and brick, to support dose mitigation and environmental clean-up. The new method for actinides in concrete and brick method utilizes a rapid sodium hydroxide fusion method, a lanthanum fluoride matrix removal step, and a column separation process with stacked TEVA, TRU and DGA Resin cartridges. Alpha emitters are prepared using rare earth microprecipitation for counting by alpha spectrometry. The method showed high chemical recoveries and effective removal of interferences. The determination of actinides in concrete and brick sample analysis can be performed in less than 8h with excellent quality for emergency samples. The rapid fusion technique is a rugged sample digestion method that ensures that any refractory actinide particles are effectively digested.

  3. Higher-order brick-tetrahedron hybrid method for Maxwell's equations in time domain

    Science.gov (United States)

    Winges, Johan; Rylander, Thomas

    2016-09-01

    We present a higher-order brick-tetrahedron hybrid method for Maxwell's equations in time domain. Brick-shaped elements are used for large homogeneous parts of the computational domain, where we exploit mass-lumping and explicit time-stepping. In regions with complex geometry, we use an unstructured mesh of tetrahedrons that share an interface with the brick-shaped elements and, at the interface, tangential continuity of the electric field is imposed in the weak sense by means of Nitsche's method. Implicit time-stepping is used for the tetrahedrons together with the interface. For cavity resonators, the hybrid method reproduces the lowest non-zero eigenvalues with correct multiplicity and, for geometries without field singularities from sharp corners or edges, the numerical eigenvalues converge towards the analytical result with an error that is approximately proportional to h2p, where h is the cell size and p is the polynomial order of the elements. For a rectangular waveguide, a layer of tetrahedrons embedded in a grid of brick-shaped elements yields a low reflection coefficient that scales approximately as h2p. Finally, we demonstrate hybrid time-stepping for a lossless closed cavity resonator, where the time-domain response is computed for 300,000 time steps without any signs of instabilities.

  4. Development of a Low-Cost Airborne Ultrasound Sensor for the Detection of Brick Joints behind a Wall Painting

    Science.gov (United States)

    García-Diego, Fernando-Juan; Bravo, José María; Pérez-Miralles, Juan; Estrada, Héctor; Fernández-Navajas, Angel

    2012-01-01

    Non-destructive methods are of great interest for the analysis of cultural heritage. Among the different possible techniques, this paper presents a low cost prototype based on the emission and reception of airborne ultrasound without direct contact with the test specimen. We successfully performed a method test for the detection of brick joints under a XVth century Renaissance fresco of the Metropolitan Cathedral of the city of Valencia (Spain). Both laboratory and in situ results are in agreement. Using this prototype system, an early moisture detection system has been installed in the dome that supports the fresco. The result is encouraging and opens interesting prospects for future research. PMID:22438711

  5. Development of a Low-Cost Airborne Ultrasound Sensor for the Detection of Brick Joints behind a Wall Painting

    Directory of Open Access Journals (Sweden)

    Angel Fernández-Navajas

    2012-01-01

    Full Text Available Non-destructive methods are of great interest for the analysis of cultural heritage. Among the different possible techniques, this paper presents a low cost prototype based on the emission and reception of airborne ultrasound without direct contact with the test specimen. We successfully performed a method test for the detection of brick joints under a XVth century Renaissance fresco of the Metropolitan Cathedral of the city of Valencia (Spain. Both laboratory and in situ results are in agreement. Using this prototype system, an early moisture detection system has been installed in the dome that supports the fresco. The result is encouraging and opens interesting prospects for future research.

  6. Effect of olive mill waste addition on the properties of porous fired clay bricks using Taguchi method.

    Science.gov (United States)

    Sutcu, Mucahit; Ozturk, Savas; Yalamac, Emre; Gencel, Osman

    2016-10-01

    Production of porous clay bricks lightened by adding olive mill waste as a pore making additive was investigated. Factors influencing the brick manufacturing process were analyzed by an experimental design, Taguchi method, to find out the most favorable conditions for the production of bricks. The optimum process conditions for brick preparation were investigated by studying the effects of mixture ratios (0, 5 and 10 wt%) and firing temperatures (850, 950 and 1050 °C) on the physical, thermal and mechanical properties of the bricks. Apparent density, bulk density, apparent porosity, water absorption, compressive strength, thermal conductivity, microstructure and crystalline phase formations of the fired brick samples were measured. It was found that the use of 10% waste addition reduced the bulk density of the samples up to 1.45 g/cm(3). As the porosities increased from 30.8 to 47.0%, the compressive strengths decreased from 36.9 to 10.26 MPa at firing temperature of 950 °C. The thermal conductivities of samples fired at the same temperature showed a decrease of 31% from 0.638 to 0.436 W/mK, which is hopeful for heat insulation in the buildings. Increasing of the firing temperature also affected their mechanical and physical properties. This study showed that the olive mill waste could be used as a pore maker in brick production.

  7. Studying boundary elements’ behaviour using masonry walls built with high-resistance bricks

    Directory of Open Access Journals (Sweden)

    Juan Carlos Restrepo Mejía

    2010-04-01

    Full Text Available This research was aimed at studying the behaviour of masonry walls built with and without boundary elements at both ends when sublected to monotonic and cyclic lateral loads. The walls were designed to have the greatest resistance, following NSR-98 recommendations (normas Colombianas de diseno y construcción sismo resistente, except for shear reinforcement. XTRACT software was used for finding axial load cf bending moment and curvature cf bending moment curves. One monotonic test and two cyclic tests were performed for each type of wall. Experimental results from the walls’ lateral load cf displacement curves were used for determining their ability to dissipate energy on an inelastic range (“R” force-reduction factor for seismic loads and displacement and curvature malleability. It was found that walls built without boundary elements suffered shear failure with cracks in a stepped configuration along the bricks’ edge. The type of failure for walls built with boundary elements was shear failure in the central panel with cracks in a stepped configuration, in addition to compression failure at the edge of the boundary elements with vertical cracks on the lower part of the wall and at the contact between the wall and the boundary element. Comparison with two other studies carried out at the Universidad Nacional showed similar cyclic behaviour, regardless of the clay brick’s strength. The “R” values obtained for both types of walls were lower than the recommended values given by NSR-98. It was determined that walls having boundary element have greater displacement malleability than walls without boundary elements.

  8. Large-scale, thick, self-assembled, nacre-mimetic brick-walls as fire barrier coatings on textiles

    Science.gov (United States)

    Das, Paramita; Thomas, Helga; Moeller, Martin; Walther, Andreas

    2017-01-01

    Highly loaded polymer/clay nanocomposites with layered structures are emerging as robust fire retardant surface coatings. However, time-intensive sequential deposition processes, e.g. layer-by-layer strategies, hinders obtaining large coating thicknesses and complicates an implementation into existing technologies. Here, we demonstrate a single-step, water-borne approach to prepare thick, self-assembling, hybrid fire barrier coatings of sodium carboxymethyl cellulose (CMC)/montmorillonite (MTM) with well-defined, bioinspired brick-wall nanostructure, and showcase their application on textile. The coating thickness on the textile is tailored using different concentrations of CMC/MTM (1–5 wt%) in the coating bath. While lower concentrations impart conformal coatings of fibers, thicker continuous coatings are obtained on the textile surface from highest concentration. Comprehensive fire barrier and fire retardancy tests elucidate the increasing fire barrier and retardancy properties with increasing coating thickness. The materials are free of halogen and heavy metal atoms, and are sourced from sustainable and partly even renewable building blocks. We further introduce an amphiphobic surface modification on the coating to impart oil and water repellency, as well as self-cleaning features. Hence, our study presents a generic, environmentally friendly, scalable, and one-pot coating approach that can be introduced into existing technologies to prepare bioinspired, thick, fire barrier nanocomposite coatings on diverse surfaces.

  9. Silica Refractory Bricks

    Institute of Scientific and Technical Information of China (English)

    Yu Lingyan; Peng Xigao

    2011-01-01

    @@ 1.Scope This standard specifies the classification,technical requirements,test methods,quality appraisal procedures,packing,marking,transportation,storage,and quality certificate of silica refractory bricks.This standard is applicable to silica refractory bricks with single weight≤40 kg.

  10. Influence of Brick Walls on the Temperature Distribution in Steel Columns in Fire

    Directory of Open Access Journals (Sweden)

    António J. P. Moura Correia

    2009-01-01

    Full Text Available This paper reports on a study of steel columns embedded in walls in fire. Several fire resistance tests were carried out at the Laboratory of Testing Materials and Structures of the University of Coimbra, in Portugal. The temperatures registered in several points of the experimental models are compared with those obtained in numerical simulations carried out with the SUPERTEMPCALC finite element program. 

  11. Evaluation of Coating Removal and Aggressive Surface Removal Surface Technologies Applied to Concrete Walls, Brick Walls, and Concrete Ceilings

    Energy Technology Data Exchange (ETDEWEB)

    Lagos, L.E.; Ebadian, M.A.

    1997-11-01

    The purpose of this investigation was to test and evaluate innovative and commercially available technologies for the surface decontamination of walls and ceilings. This investigation supports the DOE's objectives of reducing risks to human health and the environment through its restoration projects at FEMP and MEMP. This project was performed at the Hemispheric Center for Environmental Technology (HCET) at Florida International University (FIU), where one innovative and four commercially available decontamination technologies were evaluated under standard, non-nuclear testing conditions. The performance data generated by this project will assist DOE site managers in the selection of the safest, most efficient, and most cost-effective decontamination technologies to accomplish their remediation objectives.

  12. SHAPE AND CONSTRUCTION OF BRICK VAULTS. CRITERIA, METHODS AND TOOLS FOR A POSSIBLE CATALOGUE

    Directory of Open Access Journals (Sweden)

    R. Brumana

    2017-05-01

    Full Text Available The use of cloister vaults in the construction of noble buildings, as covering elements for square or rectangular rooms, is widespread and well-known. The geometric continuity at the intrados makes generally possible the execution all over the span of frescoes, stucco and decorations. The construction of brick vaults, from the late Middle Age, was sped up by limiting the centering to the wooden planks arches that were instrumental in the profile determination. Nowadays, the availability of several procedures, phases and tools for carrying out a survey allows to draw reliable assumptions about the construction methods and the execution time. It is mandatory to determine the properties of the binders, the shape and dimensions of the bricks, and to carry out a comparison between the geometry of the intrados surface and the evidences emerging at the extrados. The support of the laser scanner technique allows to accurately identify the surface profile and thickness. All these indications, in turn, are useful, in view of an interpretation of the structural behavior, to identify weaknesses, and to highlight contributing factors of instability (if any. The paper focuses on a well-documented case, the Magio Grasselli palace in Cremona in which the cloister vaults of two main rooms show different construction systems, although they were built almost at the same time. The thermographic recordings and laser-scanner surveys highlight the various arrangements used for the cloister vaults.

  13. Shape and Construction of Brick Vaults. Criteria, Methods and Tools for a Possible Catalogue

    Science.gov (United States)

    Brumana, R.; Condoleo, P.; Grimoldi, A.; Landi, A. G.

    2017-05-01

    The use of cloister vaults in the construction of noble buildings, as covering elements for square or rectangular rooms, is widespread and well-known. The geometric continuity at the intrados makes generally possible the execution all over the span of frescoes, stucco and decorations. The construction of brick vaults, from the late Middle Age, was sped up by limiting the centering to the wooden planks arches that were instrumental in the profile determination. Nowadays, the availability of several procedures, phases and tools for carrying out a survey allows to draw reliable assumptions about the construction methods and the execution time. It is mandatory to determine the properties of the binders, the shape and dimensions of the bricks, and to carry out a comparison between the geometry of the intrados surface and the evidences emerging at the extrados. The support of the laser scanner technique allows to accurately identify the surface profile and thickness. All these indications, in turn, are useful, in view of an interpretation of the structural behavior, to identify weaknesses, and to highlight contributing factors of instability (if any). The paper focuses on a well-documented case, the Magio Grasselli palace in Cremona in which the cloister vaults of two main rooms show different construction systems, although they were built almost at the same time. The thermographic recordings and laser-scanner surveys highlight the various arrangements used for the cloister vaults.

  14. Fireclay Refractory Bricks

    Institute of Scientific and Technical Information of China (English)

    Zhang Xiaohui

    2010-01-01

    @@ 1 Scope This standard specifies the classification,brand,shape,dimension,technical requirements,test methods,quality appraisal procedures,packing,marking,transportation,storage,and quality certificate of fireclay refractory bricks.

  15. Slide Gate Bricks

    Institute of Scientific and Technical Information of China (English)

    Wang Jing; Peng Xigao

    2010-01-01

    @@ 1 Scope This standard specifies the classification,shape,dimension,technical requirements,test methods,quality appraisal procedures,packing,marking,transportation,storage,and quality certificate of slide gate bricks.

  16. Thermal analysis of a building brick containing phase change material

    Energy Technology Data Exchange (ETDEWEB)

    Alawadhi, E.M. [Kuwait Univ., Safat (Kuwait). Dept. of Mechanical Engineering

    2008-07-01

    This paper presents the thermal analysis of a building brick containing phase change material (PCM) to be used in hot climates. The objective of using the PCM is to utilize its high latent heat of fusion to reduce the heat gain by absorbing the heat in the bricks through the melting process before it reaches the indoor space. The considered model consists of bricks with cylindrical holes filled with PCM. The problem is solved in a two-dimensional space using the finite element method. The thermal effectiveness of the proposed brick-PCM system is evaluated by comparing the heat flux at the indoor surface to a wall without the PCM during typical working hours. A paramedic study is conducted to assess the effect of different design parameters, such as the PCM's quantity, type, and location in the brick. The results indicate that the heat gain is significantly reduced when the PCM is incorporated into the brick, and increasing the quantity of the PCM has a positive effect. PCM cylinders located at the centerline of the bricks shows the best performance. (author)

  17. Industrial wastes for firing Bricks

    Institute of Scientific and Technical Information of China (English)

    ZhanXuanye; LuGuansheng; Gaojun

    2005-01-01

    The paper discusses the feasibility on utilizing high-calcium industrial wastes in firing brick. In China, industrial wastes with over 10% calcium oxide is not regarded as raw materials for producing brick, so it is limited to use industrial wastes. The paper gives out the ideas that high-calcium industrial wastes can be used to produce fired brick by good raw material preparation process and proper methods.

  18. Chinese Standards on Refractories Fireclay Brick and Semi-silica Brick for Coke Oven

    Institute of Scientific and Technical Information of China (English)

    Wang Jing

    2009-01-01

    @@ 1 Scope This standard specifies the technical requirements,test methods,quality appraisal procedure,packing,transportation,storage,and quality certificate of fireclay brick and semi-silica brick for coke oven. This standard is applicable to the fireclay brick and semi-silica brick for coke oven,and the bricks for inner linings of carbon furnace,gas generator and shaft furnace.

  19. Study on compressive strength of ancient brick wall of the mosque in Qiqihar city%基于齐齐哈尔市清真寺古砖墙抗压强度研究

    Institute of Scientific and Technical Information of China (English)

    王蕊

    2015-01-01

    以齐齐哈尔市清真寺为对象,进行了古代砖墙的抗压强度检测.根据检测结果,得出抗压强度沿墙体高度的变化趋势;给出古代砖的抗压强度与现在普通烧结砖的抗压强度的对比.%As object, the compressive strength test of the ancient brick wall of Mosque in qiqihaer city has been done .According to the test results , it is concluded that the variation trends of compressive strength along the wall height and has given the compressive strength of ancient brick compared with the strength of the now common sintered brick.

  20. Stabilization of endangered part of structures by building dry brunt brick buttressing, critical case study of plane wall in DKG-North Area, Mohenjo daro

    Science.gov (United States)

    Shaikh, J. M.; Park, J.

    2013-07-01

    'World Heritage Sites' are places or buildings of outstanding universal value recognized as constituting a world heritage 'for whose protection it is the duty of the international community as a whole to co-operate'. The concept of World Heritage is at the core of the World Heritage Convention, adopted by Heritage List as a means of identifying, protecting, conserving and presenting those parts of the world's natural and cultural heritage that are of sufficient 'outstanding universal value' to be the responsibility of the international community as a whole. By joining the Convention, nation states are pledged to safeguard the WH S by protecting their national heritage. UNESCO in 1972, to which 160 nations have now been adhered. The Convention came into force in 1975 and established a Site in their territory as part of a universally agreed policy for World. Moenjodaro site covering an area of 555 Acres out of which only 10 % of it has been excavated by exposing 50 Kilometer standing walls. The wall of the main street of DK G Area, Mohen jo Daro partially deformed, due to the torque effects this is studied here on a lateral cross wall in the chief house. Furthermore, the resulting behaviour of the bucking wall demonstrates the significant loadbearing capacity of the structure under service conditions and its high sensitivity to imposed changes of the geometry. Although the tensile stresses exceeded the flexural strength at the vertices and the length of the wall, hence both the geometry and condition of this area are critical for the safety of the wall. The results of this study can improve the assessment and thus help in the preservation of many important structures of the metropolitan city. Here the hydrous characteristic of the brick is studied as a general phenomenon, it is observed that the remains of the sites located in Sindh suffered a lot mostly due to age, human neglect variations of atmospheric condition, severe temperature and natural disasters. The main

  1. 局部配筋对页岩空心砖墙体抗震性能影响试验研究%Experimental Study on Seismic Behavior of Shale Hollow Brick Masonry Walls Influenced by Partial Reinforcement

    Institute of Scientific and Technical Information of China (English)

    陈万山; 杨德健

    2011-01-01

    作为非承重结构材料,页岩空心砖能够较好地替代黏土砖.但空心砖墙体抗震性能较差,严重影响其在工程中的应用.局部配筋是提高砌体结构抗震性能的主要方法之一.为研究局部配筋对页岩空心砖墙体抗震性能的影响,对3种砌筑形式6组墙体进行了低周反复荷载试验.研究了局部配筋对该结构承载力、滞回性能、延性和耗能能力等方面的影响.研究结果表明:局部配筋不仅可以提高墙体承载力,而且可以显著提高墙体抗震性能和变形性能.%Shale hollow bricks can take the place of common bricks to some extent. But the weak seismic behavior of hollow brick masonry walls affects the application of the hollow bricks in the engineering. Partical reinforcement in the wall can improve the seismic performance of walls. In order to investigate the effect of seismic behavior of this structure, the low cyclic reversed lateral loading tests on six pieces of shale hollow brick masonry walla which used three bricklaying patterns have been carried out. The bearing capacity, hyateretic characteristics, ductility and energy dissipation were researched. The result of investigation shows that setting steel reinforcement in the wall not only can improve the bearing capacity of the masonry walls,but also can greatly improve the seismic behavior and the deformation behavior of the wall.

  2. 松江砖刻照壁文物保护工程勘察%On observation of protection for carved brick screen walls at Songjiang

    Institute of Scientific and Technical Information of China (English)

    许利军; 陈洋; 李占鸿

    2012-01-01

    针对松江砖刻照壁风化日益严重并存在倾斜的现状进行分析,采用三维激光扫描仪对照壁进行精细化测绘并根据扫描数据进行分析、绘制立面图,由测绘及勘察结果对照壁损坏原因进行分析并提出相应的加固修缮建议。%The paper analyzes the current status for the carved brick screen walls at Songjiang, which suffer from the serious weathering and inclination, adopts the three-dimension laser scanner to undertake the refined mapping of the screen walls, analyzes these scanned data, and draws the stereogram, analyzes the damages of the screen walls according to the surveyed and observed results, and points out respective repair suggestions.

  3. Magnesia Bricks and Magnesia Alumina Bricks GB/T 2275-2007

    Institute of Scientific and Technical Information of China (English)

    Wang Jing; Peng Xigao

    2010-01-01

    @@ 1 Scope This standard specifies the classification,techni-cal requirements,test methods,quality appraisal pro-cedures,marking,packing,transportation,storage and quality certificate of magnesia bricks and magnesia alumina bricks.

  4. Experimental study on pressure bearing capacity of recycled aggregate concrete perforated brick walls%再生混凝土多孔砖墙体受压承载力试验研究

    Institute of Scientific and Technical Information of China (English)

    郭樟根; 徐一凡; 孙伟民; 沈丹; 陈建龙

    2011-01-01

    再生骨料替代率为75%,再生混凝土多孔砖强度等级接近MU10.考察再生混凝土多孔砖墙体的受压性能,通过对2片再生混凝土多孔砖墙体进行轴心竖向荷载作用下的试验研究.结果表明,再生混凝土多孔砖墙体在竖向荷载作用下的破环全过程和普通混凝七多孔砖墙体基本相似,受力全过程分为3个阶段:弹性阶段、裂缝发展阶段以及破坏阶段.偏于安全考虑,再生混凝土多孔砖砌体的轴心受压承载力可参照GB 50003-2010(征求意见稿)中有关砌体受压承载力计算公式进行计算.%The strength grade of recycled concrete perforated brick wall is close to MU1O when the replacement ratio of recycled aggregate is 75%. The compressive performance of the recycled concrete perforated brick wall was investigated by the experimental study on two recycled concrete perforated brick walls under the function of axial vertical loading. The results show that the compression failure process of recycled concrete perforated brick wall is similar to tbat of ordinary concrete brick walls,which was divided into three stages:elastic stage,crack development stage and the destruction phase. For the sake of safety,the calculation of axial pressure bearing capacity of recycled concrete perforated brick wall can be made with reference to the formula for pressure bearing capacity of masonry as specified in standard CB 50003-2010 "Masonry Structure Design Code"(Draft).

  5. The first fly ash fired hollow brick production line with an annual capacity of 120 million bricks in China

    Institute of Scientific and Technical Information of China (English)

    ZhuYali

    2005-01-01

    The article describes the first fly ash fired hollow brick production line with an annual output of 120 million bricks in China, which is designed and contracted by Xi'an Research and Design Institute of Wall and Roof Material, commissioned by Xi Baipo Generate Electricity Ltd. Company. It is a good sample for utilizing industrial wastes to produce hollow brick.

  6. Evaluation of bricks durability using destructive and nondestructive methods (DT and NDT

    Directory of Open Access Journals (Sweden)

    Cultrone, G.

    2003-03-01

    Full Text Available We have studied the physical-mechanical behaviour of solid bricks treated with consolidants and/or water-repellents in accelerated aging tests to determine their durability. The bricks were manufactured with a quartz-rich clay lacking in carbonates to which was added small amounts of different additives (calcite, dolomite or sodium chloride. During the manufacturing process, we attempted to replicate solid bricks similar to those used in many Cultural Heritage buildings. We have concluded that silicon resin gives the best results, whatever the additive used, whereas acrylic resin gives the least satisfactory results.

    Se ha estudiado el comportamiento físico-mecánico de ladrillos macizos tratados con productos consolidantes y/o hidrofugantes frente a ensayos acelerados de alteración para evaluar su durabilidad. En la fabricación de las piezas cerámicas se ha utilizado un material arcilloso rico en cuarzo y sin carbonatos al que se han añadido pequeñas cantidades de distintos aditivos (calcita, dolomita o sal. En el proceso de elaboración se han intentado reproducir ladrillos macizos similares a los empleados en muchos edificios del Patrimonio Arquitectónico. Se concluye que el uso de resina de silicona proporciona los mejores resultados, cualquiera que sea el aditivo añadido, mientras que los resultados menos satisfactorios se han calculado cuando se ha empleado una resina acrílica.

  7. Indicating Vertical Deviation of Historical Buildings Using Geodetic Methods - Case Study of Brick and Wood Tower in Nowe Miasteczko

    Science.gov (United States)

    Mrówczyńska, Maria; Gibowski, Sławomir

    2016-09-01

    The article presents the possibilities of applying geodetic methods to determine the vertical deviation of historical buildings. In particular, the results of measurements obtained for a brick and wood Town Hall Tower located in the town of Nowe Miasteczko have been presented. Geodetic measurements of vertical deviation taken before and after carrying out repairs which were aimed at stopping or eliminating the destructive processes of degradation taking place, especially in the wooden part of the tower. During the renovation works, attention was also given to improving the technical condition of the building, which was reflected by the results of the measurements and calculations.

  8. Cracks in Fired Perforated Brick Walls Caused by Temperature Change and Some Counter-measures%烧结多孔砖墙体温度裂缝分析和预防措施

    Institute of Scientific and Technical Information of China (English)

    陆杰

    2013-01-01

    烧结多孔砖作为烧结普通砖的替代材料,因其具有性能稳定、耐久性好、容重轻、施工方便、施工效率高及保温节能等特点,并可节约土地资源,得到广泛推选使用。采用烧结多孔砖砌筑的墙体裂缝的产生与烧结普通砖有许多相似。因砌体结构房屋钢筋混凝土屋盖和烧结多孔砖墙体的线膨胀系数和刚度不同,当温度变化时,二者就会产生相对位移和内力,从而引起墙体裂缝。裂缝的产生与温度、水平阻力系数及墙体截面尺寸有关。通过对温度裂缝产生原因进行定性、定量分析,提出从设计构造、规范施工及砌体强度等方面来控制温度裂缝。%Fired perforated brick is used as a substitute for bearing wall instead of fired common bricks.It has good performance in stability,durability,low volume-weight,and thermal insu-lation,and it is convenient,highly efficient and energy-saving for construction.It also saves land resources,which is widely chosen and used.The cracks on fired perforated brick walls have a lot in common with those on fired common brick walls.Because of the differences of lin-ear expansion coefficient and stiffness between reinforced concrete roof and fired perforated brick walls,when the temperature changes,both of them bring the relative displacement and internal force, thus the crack appears on the wall.Temperature, horizontal resistance coefficient and the section size of the wall body are relevant to the crack.Based on quantitative and qualitative analysis of crack caused by temperature change,the paper provides several counter-measures against crack with regard to design conformation, standardizing construction,and the strength of masonry.

  9. Wastewater treatment efficiency of a multi-media biological aerated filter (MBAF) containing clinoptilolite and bioceramsite in a brick-wall embedded design.

    Science.gov (United States)

    Ji, Guodong; Tong, Jingjing; Tan, Yufei

    2011-01-01

    A multi-media biological aerated filter (MBAF) with clinoptilolite media was used to treat synthetic wastewater. Coal ash bioceramsite with supplemental metallic iron was added to the clinoptilolite media of MBAFs in a brick-wall embedded design. Performance parameters, such as hydraulic, organic, N and P loading capacity and microbial community composition were studied for different quantity of supplemental metallic iron contained in three MBAFs. The MBAFs with more metallic iron were found to have superior hydraulic and organic loading, and higher N and P capacities. COD, NH3-N and TP removal dropped by 7-10%, 6-7% and 4-5%, respectively, with when hydraulic loading was raised from 2.8 to 7.5 m3 m(-2) d(-1). NH3-N removal also decreased 8-9% when ammonia loading was elevated from 0.078 to 0.156 kg NH3-N m(-3) d(-1). Real-time PCR revealed a relatively stable bacterial community composed primarily of eubacteria that formed after an initial 120 d operational period. Doubling the amount of metallic iron in the bioceramsite media resulted in a twofold increase of eubacteria in the MBAF, but a decrease in the ratio of anaerobic ammonia-oxidizing bacteria to total bacteria.

  10. The 'Brick Wall' radio loss approximation and the performance of strong channel codes for deep space applications at high data rates

    Science.gov (United States)

    Shambayati, Shervin

    2001-01-01

    In order to evaluate performance of strong channel codes in presence of imperfect carrier phase tracking for residual carrier BPSK modulation in this paper an approximate 'brick wall' model is developed which is independent of the channel code type for high data rates. It is shown that this approximation is reasonably accurate (less than 0.7dB for low FERs for (1784,1/6) code and less than 0.35dB for low FERs for (5920,1/6) code). Based on the approximation's accuracy, it is concluded that the effects of imperfect carrier tracking are more or less independent of the channel code type for strong channel codes. Therefore, the advantage that one strong channel code has over another with perfect carrier tracking translates to nearly the same advantage under imperfect carrier tracking conditions. This will allow the link designers to incorporate projected channel code performance of strong channel codes into their design tables without worrying about their behavior in the face of imperfect carrier phase tracking.

  11. The Contrivance of New Mud Bricks for Restoring and Preserving the Edfa Ancient Granary - Sohag, Egypt

    Directory of Open Access Journals (Sweden)

    Mohammed EL-GOHARY

    2012-06-01

    Full Text Available A mud brick functions as an element of masonry structures. Being an integral part of a wall mass, it must be understood structurally and chemically. The susceptibility of a mud brick to be affected by decay agents depends on the type of raw materials used, the methods of construction, location, the microclimatic conditions, the mechanical and microstructural characteristics of the mud brick itself. In this research, mineralogical composition and granulometric distribution of ancient mud bricks were studied by using some scientific techniques such as XRD, SEM and electrical mechanical sieves, to determine the main components and characteristics, which will serve as reference for the contrivance of new mud bricks. In addition, special knowledge of the physical properties of historic mud bricks were defined by some scientific techniques to get some information about their properties, such as density, porosity, water absorption and shrinkage. Furthermore, all of those characteristics were studied in two groups of new mud bricks, to determine their properties. Finally, ourresults proved that the 6th category in the 1st group and the 10th category in the 2nd group are the most appropriate types for restoring and preserving the studied monument, due to their good physical properties, morphological appearances and their suitable characteristics.

  12. A novel method for a multi-level hierarchical composite with brick-and-mortar structure.

    Science.gov (United States)

    Brandt, Kristina; Wolff, Michael F H; Salikov, Vitalij; Heinrich, Stefan; Schneider, Gerold A

    2013-01-01

    The fascination for hierarchically structured hard tissues such as enamel or nacre arises from their unique structure-properties-relationship. During the last decades this numerously motivated the synthesis of composites, mimicking the brick-and-mortar structure of nacre. However, there is still a lack in synthetic engineering materials displaying a true hierarchical structure. Here, we present a novel multi-step processing route for anisotropic 2-level hierarchical composites by combining different coating techniques on different length scales. It comprises polymer-encapsulated ceramic particles as building blocks for the first level, followed by spouted bed spray granulation for a second level, and finally directional hot pressing to anisotropically consolidate the composite. The microstructure achieved reveals a brick-and-mortar hierarchical structure with distinct, however not yet optimized mechanical properties on each level. It opens up a completely new processing route for the synthesis of multi-level hierarchically structured composites, giving prospects to multi-functional structure-properties relationships.

  13. 变电站蒸压粉煤灰砖砌体围墙裂缝分析与防治%Analysis and Prevention of Substation of Autoclaved Fly Ash Brick Masonry Wall Cracks

    Institute of Scientific and Technical Information of China (English)

    邵国华

    2014-01-01

    本文结合变电站工程实际,分析了变电站工程蒸压粉煤灰砖砌体清水围墙裂缝产生的原因,从蒸压粉煤灰砖的生产、构造设计及砌筑施工等几个方面提出了防治措施。%Combining with the actual substation engineering, Analyzed the causes of transformer substation project of autoclaved fly ash brick masonry wall cracks in water, Puts forward the prevention measures from the aspects of production, structure design and masonry construction of autoclaved fly ash brick.

  14. The production process for water penetrated brick

    Institute of Scientific and Technical Information of China (English)

    SunGuofeng

    2005-01-01

    Waste penetrated brick, which is a green building material with good water penetration, high strength, lower firing temperature, lower production cost, good appearance and good structure, can holding ground water lever. This article analysis the production process and related factor for water penetrated brick:proper particle size distribution, proper shaping method, proper press and proper firing can ensure to produce good quality water penetrated brick.

  15. Toward Applications for DNA Nanotechnology-More Bricks To Build With.

    Science.gov (United States)

    Dietz, Hendrik

    2016-06-16

    Another brick in the wall: DNA nanotechnology has come a long way since its initial beginnings. This would not be possible without the continued development of methods for DNA assembly and new uses for DNA as a material. This Special Issue highlights some of the newest building blocks for nanodevices based on DNA.

  16. Impact of wind-driven rain on historic brick wall buildings in a moderately cold and humid climate: Numerical analyses of mould growth risk, indoor climate and energy consumption

    DEFF Research Database (Denmark)

    Masaru, Abuku; Janssen, Hans; Roels, Staf

    2009-01-01

    response, mould growth at interior wall surfaces, indoor climate and energy consumption. First the WDR load oil the facades of a 4 m x 4 m x 10 m tower is determined. Then the hygrothermal behaviour of the brick walls is analysed oil a horizontal slice through the tower. The simulations demonstrate...... that WDR loads can have a significant impact on mould growth especially at the edges of the walls. Finally, for the case analysed, the WDR load Causes a significant increase of indoor relative humidity and energy consumption for heating. (C) 2008 Elsevier B.V. All rights reserved.......This paper gives an onset to whole building hygrothermal modelling in which the interaction between interior and exterior climates via building enclosures is simulated under a moderately cold and humid climate. The focus is particularly on the impact of wind-driven rain (WDR) oil the hygrothermal...

  17. Analysis and research on heat preservation system preventing fromcondensation inside the wall of sintered gangue cork brick%烧结煤矸石多孔砖墙内保温系统防结露分析与研究

    Institute of Scientific and Technical Information of China (English)

    宋岩丽

    2012-01-01

    This thesis researches the heat preservation system inside the outer-wall built of sintered gangue cork brick and glassy tiny bead wanning mortar. It tests its outer wall heat transfer coefficient and mainly analyzes the thermal bridge area from condensation. At last, the writer thinks that the heat preservation system inside the outer-wall built of sintered gangue cork brick can be used in the multiple-storey buildings below six and can fully meet the needs of 65% energy-saving in cold areas.%以烧结煤矸石多孔砖与玻化微珠保温砂浆构成的外墙内保温系统为研究对象,对其外墙传热系数进行测试,并重点对热桥部位防结露进行计算分析.分析认为,烧结煤矸石多孔砖外墙内保温体系用于6层以下的多层建筑,在寒冷地区完全可以满足节能65%目标要求.

  18. Comparative analysis of dose rates in bricks determined by neutron activation analysis, alpha counting and X-ray fluorescence analysis for the thermoluminescence fine grain dating method

    Science.gov (United States)

    Bártová, H.; Kučera, J.; Musílek, L.; Trojek, T.

    2014-11-01

    In order to evaluate the age from the equivalent dose and to obtain an optimized and efficient procedure for thermoluminescence (TL) dating, it is necessary to obtain the values of both the internal and the external dose rates from dated samples and from their environment. The measurements described and compared in this paper refer to bricks from historic buildings and a fine-grain dating method. The external doses are therefore negligible, if the samples are taken from a sufficient depth in the wall. However, both the alpha dose rate and the beta and gamma dose rates must be taken into account in the internal dose. The internal dose rate to fine-grain samples is caused by the concentrations of natural radionuclides 238U, 235U, 232Th and members of their decay chains, and by 40K concentrations. Various methods can be used for determining trace concentrations of these natural radionuclides and their contributions to the dose rate. The dose rate fraction from 238U and 232Th can be calculated, e.g., from the alpha count rate, or from the concentrations of 238U and 232Th, measured by neutron activation analysis (NAA). The dose rate fraction from 40K can be calculated from the concentration of potassium measured, e.g., by X-ray fluorescence analysis (XRF) or by NAA. Alpha counting and XRF are relatively simple and are accessible for an ordinary laboratory. NAA can be considered as a more accurate method, but it is more demanding regarding time and costs, since it needs a nuclear reactor as a neutron source. A comparison of these methods allows us to decide whether the time- and cost-saving simpler techniques introduce uncertainty that is still acceptable.

  19. Bauxite Based Bricks for Steel Ladle

    Institute of Scientific and Technical Information of China (English)

    Yu Lingyan; Peng Xigao

    2011-01-01

    @@ 1.Scope This standard specifies the classification,technical requirements,test methods,inspection rules,packing,marking,transportation,storage,and quality certificate of bauxite based bricks for steel ladle linings.This standard is applicable to bauxite based bricks for working layer of steel ladle.

  20. Electrokinetic removal of salt from brick masonry

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Pedersen, Anne Juul; Rörig-Dalgaard, Inge

    2006-01-01

    A method to effectively remove salts from masonry is lacking. The present study aims at determining the removal efficiency of salts from bricks in an applied low current electric DC field. At first an investigation on removal of NaCl and Na(NO3)2 from spiked bricks in laboratory scale was conducted...

  1. Electrokinetic removal of salt from brick masonry

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Pedersen, Anne Juul; Rörig-Dalgaard, Inge

    2006-01-01

    A method to effectively remove salts from masonry is lacking. The present study aims at determining the removal efficiency of salts from bricks in an applied low current electric DC field. At first an investigation on removal of NaCl and Na(NO3)2 from spiked bricks in laboratory scale was conducted...

  2. Development of Reproducing Alumina-Magnesia-Carbon Bricks

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The reproducing alumina-magnesia-carbon bricks were prepared with the dumped bricks as starting materials. The bulk density, apparent porosity, crushing strength, modolus of rupture and slag resistance of the specimen were analyzed. The results show that the used refractories can be reused and recycled by the right method. The reproducing alumina-magnesia-carbon bricks with better abilities were prepared.

  3. A fly ash and shale fired brick production line

    Institute of Scientific and Technical Information of China (English)

    ZhuYali

    2005-01-01

    The article describes the fly ash and shale fired brick production line with annual output of 1250 million bricks, designed by Xi'an Research and Design Institute of Wall and Roof Material, commissioned by QinDian Building Material Subcompany, and set an example for using fly ash and shale in China.

  4. Randomized BioBrick assembly: a novel DNA assembly method for randomizing and optimizing genetic circuits and metabolic pathways.

    Science.gov (United States)

    Sleight, Sean C; Sauro, Herbert M

    2013-09-20

    The optimization of genetic circuits and metabolic pathways often involves constructing various iterations of the same construct or using directed evolution to achieve the desired function. Alternatively, a method that randomizes individual parts in the same assembly reaction could be used for optimization by allowing for the ability to screen large numbers of individual clones expressing randomized circuits or pathways for optimal function. Here we describe a new assembly method to randomize genetic circuits and metabolic pathways from modular DNA fragments derived from PCR-amplified BioBricks. As a proof-of-principle for this method, we successfully assembled CMY (Cyan-Magenta-Yellow) three-gene circuits using Gibson Assembly that express CFP, RFP, and YFP with independently randomized promoters, ribosome binding sites, transcriptional terminators, and all parts randomized simultaneously. Sequencing results from 24 CMY circuits with various parts randomized show that 20/24 circuits are distinct and expression varies over a 200-fold range above background levels. We then adapted this method to randomize the same parts with enzyme coding sequences from the lycopene biosynthesis pathway instead of fluorescent proteins, designed to independently express each enzyme in the pathway from a different promoter. Lycopene production is improved using this randomization method by about 30% relative to the highest polycistronic-expressing pathway. These results demonstrate the potential of generating nearly 20,000 unique circuit or pathway combinations when three parts are permutated at each position in a three-gene circuit or pathway, and the methodology can likely be adapted to other circuits and pathways to maximize products of interest.

  5. Residential mercury contamination in adobe brick homes in Huancavelica, Peru.

    Science.gov (United States)

    Hagan, Nicole; Robins, Nicholas; Hsu-Kim, Heileen; Halabi, Susan; Espinoza Gonzales, Ruben Dario; Richter, Daniel deB; Vandenberg, John

    2013-01-01

    This is the first study of adobe brick contamination anywhere in the world. Huancavelica, Peru is the site of historic cinnabar refining and one of the most mercury (Hg) contaminated urban areas in the world. Over 80% of homes in Huancavelica are constructed with adobe bricks made from Hg contaminated soil. In this study we measured total Hg concentrations in adobe brick, dirt floor, surface dust, and air samples from the interior of 60 adobe brick houses located in four neighborhoods. Concentrations of total Hg in adobe bricks, dirt floors, and surface dust ranged from 8.00 to 1070 µg/g, 3.06 to 926 µg/g, and 0.02 to 9.69 µg/wipe, respectively, with statistically significant differences between the four neighborhoods. Concentrations of Hg in adobe brick and dirt floor samples in Huancavelica were orders of magnitude higher than in Ayacucho, a non-mining town in Peru. A strong correlation exists between total Hg concentrations in adobe bricks and dirt floors which confirms that adobe bricks were being made on-site and not purchased from an off-site source. A strong correlation between surface dust and adobe bricks and dirt floors indicates that walls and floors serve as indoor sources of Hg contamination. Elemental Hg vapor concentrations were below detection (bricks, may be a substantial source of residential Hg exposure in silver or gold refining communities where Hg is produced or used for amalgamation in artisanal gold production.

  6. DYNAMIC HEAT TRANSFER OF BRICK WALL FILLED WITH PHASE CHANGE MATERIALS (PCM) UNDER FLUCTUATING TEMPERATURES%交变温度作用下填充PCM砖墙的动态传热特性

    Institute of Scientific and Technical Information of China (English)

    吴梁玉; 陈永平; 张程宾; 施明恒

    2012-01-01

    采用enthalpy-porosity法建立交变温度作用下填充相变材料(PCM)的砖墙内伴有熔化和凝固相变过程的动态传热模型并进行数值计算,比较实心砖墙与PCM砖墙的室内侧壁温响应变化,分析讨论墙体中PCM填充份额和PCM填充空间分布对墙体动态传热过程的影响,并对填充PCM墙体结构进行性能评价.研究结果表明,填充PCM的砖墙结构由于其孔隙中填充的PCM通过熔化/凝固相变作用蓄存了潜热,有效削弱了外界温度变化对室内壁温的影响,对室内温度起到削峰填谷的作用.随着砖墙中填充PCM份额的增加,室内侧温度的波动幅度明显减小,且对室外交变温度作用的滞后效果也相应得到增强.对于相同的PCM填充份额,PCM的填充分布方式对砖墙的保温性能和温度滞后效果也存在一定影响,但影响并不明显.%A model for thermal conduction accompanied with solidification and melting processes was developed by enthalpy-porosity technique and numerically analyzed to investigate the dynamic heat transfer characteristics of the brick wall filled with Phase Change Materials (PCM). The dynamic heat transfer characteristic, which is represented by inside wall surface temperature response, of brick wall filled with PCM was evaluated and compared with that of solid brick wall. The effects of PCM amount as well as spatial distribution of PCM on the dynamic heat transfer characteristic of the brick wall were investigated and discussed. It is indicated that the influence of outdoor temperature fluctuation on indoor temperature is weaken due to the filling of PCM, which can store latent heat via solidification or melting processes. In addition, with the increasing filling amount of PCM, the fluctuation of inside wall surface temperature is obviously smoothed. Correspondingly, the hysteresis in response to the outdoor temperature fluctuation is enhanced. However, unlike the PCM amount, the spatial distribution of PCM

  7. 发泡水泥对日光温室黏土砖墙保温蓄热性能的改善效果%Improving effect of heat insulation performance of brick wall thickened with foam cement in solar greenhouse

    Institute of Scientific and Technical Information of China (English)

    李明; 魏晓明; 周长吉; 郑禾; 李小明

    2014-01-01

    The wall of a Chinese solar greenhouse can absorb heat during daytime and supply heat into the greenhouse during nighttime. It can help the solar greenhouse to maintain high indoor air temperature during winter nighttime with little or no supplemental heating. The brick wall is one of the popular walls. However, after a long period of use, walls have the bad performance on heat insulation and sealing. To solve the problems, we proposed to thicken the brick wall with foam cement to decrease its heat loss and keep the heat in the wall as much as possible. Then, the stored heat that the wall can supply during the nighttime can be increased. In this study, a solar greenhouse with the brick wall, which was composed of 120 mm thick brick, 100 mm thick polystyrene board, and 240 mm thick brick (from indoor to outdoor), was used as the control greenhouse. The test greenhouse had same structure and management with the control greenhouse, but its brick wall was thickened with 200 mm thick foam cement on the outdoor side. This wall was defined as the transformed wall. The heat insulation and supply performances of the two solar greenhouses’ walls were compared based on the data collected in a typical sunny day and a cloudy day. As for the heat insulation performance, the outdoor surface temperatures of the brick wall and the transformed wall were (2.8±0.9) and (0.8±0.2)℃ higher than the outdoor air temperature, respectively, in the nighttime of the sunny day. The maximum heat flux in the foam cement was about 9%of that on the outdoor surface of the brick wall. A similar phenomenon was also observed in the nighttime of the cloudy day. The results indicated that thickening the brick wall with foam cement could decrease the heat loss of the wall and keep more heat in the wall. As for the heat supply performance, the indoor surface temperatures of the brick wall and the transformed wall were (1.5±0.5) and (2.4±0.2)℃higher than the outdoor air temperature, respectively

  8. Production parameters of sand-lime bricks with a view to reduction of heat gaps in walls. Final report; Herstellparameter von Kalksand-Spezialbaustoffen fuer die Abschwaechung von Waermebruecken im Mauerwerksbau. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Eden, W. [Forschungsvereinigung ' Kalk-Sand' e.V., Hannover (Germany); Buhl, J.C. [Hannover Univ. (Germany). Inst. fuer Mineralogie

    2002-02-01

    Sand-lime bricks with special characteristics can reduce heat gaps in walls, thus reducing the heating energy consumption of a building. Special physical characteristics are required for this, i.e. high compressive strength and low thermal conductivity. The report describes the interdependences between raw material characteristics, production processes and the properties of the resulting sand-lime bricks. [German] Im Rahmen des energiesparenden Waermeschutzes gewinnen konstruktive Massnahmen zur Reduzierung von Waermeverlusten zunehmend an Bedeutung. Beispielsweise kann bei der Anwendung von Kalksandstein-Mauerwerk durch den gezielten Einsatz von speziell entwickelten Kalksand-Leichtsteinen ein erhoehter Waermestrom ueber Waermebruecken verringert werden. Auf diese Weise kann ein weiterer Beitrag zur Reduzierung des Heizenergiebedarfs geleistet werden. Mauersteine, die zur Abschwaechung von Waermebruecken verwendet werden, muessen besondere Anforderungen hinsichtlich ihrer physikalischen Eigenschaften erfuellen. So ist die Kombination aus einer ausreichend hohen Steindruckfestigkeit und einer gleichzeitig niedrigen Waermeleitfaehigkeit entscheidend. Die vorliegende Arbeit befasst sich mit den Zusammenhaengen zwischen den Rohstoffeigenschaften, den verfahrenstechnischen Herstellbedingungen und den Eigenschaftswerten von Kalksand-Leichtsteinen fuer die Abschwaechung von Waermebruecken. (orig.)

  9. Silica Brick for Hot Blast Stove

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ 1 Scope This standard specifies the glossary and definition, marking, shape and dimension, technical requirements, test method, quality appraisal procedure, packing, label, transportation, storage and quality certification of silica brick for hot blast stove.

  10. Fireclay Refractory Bricks for Hot Blast Stove

    Institute of Scientific and Technical Information of China (English)

    Wang Jing; Zhang Yongfang; Chai Junlan

    2008-01-01

    @@ 1 Scope This standard specifies the classification, shape, dimension, technical requirements, test method,inspection rules, packing, marking,transportation,storage and quality certification of fireclay refractory bricks for hot blast stove.

  11. Burned Microporous Alumina-Graphite Brick

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ 1 Scope This standard specifies the definition,classifica-tion,technical requirements,test methods,inspection rules,marking,packing,transportation and quality certificate of burned microporous alumina-graphite brick.

  12. Methods & Strategies: Put Your Walls to Work

    Science.gov (United States)

    Jackson, Julie; Durham, Annie

    2016-01-01

    This column provides ideas and techniques to enhance your science teaching. This month's issue discusses planning and using interactive word walls to support science and reading instruction. Many classrooms have word walls displaying vocabulary that students have learned in class. Word walls serve as visual scaffolds to support instruction. To…

  13. A Spray Pyrolysis Method to Grow Carbon Nanotubes on Carbon Fibres, Steel and Ceramic Bricks.

    Science.gov (United States)

    Vilatela, Juan J; Rabanal, M E; Cervantes-Sodi, Felipe; García-Ruiz, Máximo; Jiménez-Rodríguez, José A; Reiband, Gerd; Terrones, Mauricio

    2015-04-01

    We demonstrate a spray pyrolysis method to grow carbon nanotubes (CNTs) with high degree of crystallinity, aspect ratio and degree of alignment on a variety of different substrates, such as conventional steel, carbon fibres (CF) and ceramics. The process consists in the chemical vapour deposition of both a thin SiO2 layer and CNTs that subsequently grow on this thin layer. After CNT growth, increases in specific surface by factors of 1000 and 30 for the steel and CF samples, respectively, are observed. CNTs growth on ceramic surfaces results in a surface resistance of 37.5 Ohm/sq. When using conventional steel as a rector tube, we observed CNTs growth rates of 0.6 g/min. Details of nanotube morphology and the growth mechanism are discussed. Since the method discussed here is highly versatile, it opens up a wide variety of applications in which specific substrates could be used in combination with CNTs.

  14. Magnesia Calcia Brick YB/T 4116-2003

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ 1 Scope This standard specifies the classification, techni-cal requirements, test methods, inspection rules, packing, marking, transportation, storage and quality certificate of magnesia ealcia brick.

  15. Magnesia Brick GB/T 2275-2001

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ 1 Scope This standard specifies the classification, technical requirements, test method, quality examination regulation, packing, label, transportation, storage and quality certification of magnesia brick.

  16. China's brick history and conservation

    DEFF Research Database (Denmark)

    Shu, C. X.; Cantisani, E.; Fratini, F.

    2017-01-01

    Fired bricks have been used for construction purposes in China for at least two thousand years. Since the mid-19th century the manufacture of bricks has shifted from an old to a new system. The unique Chinese blue brick has been gradually replaced by the European red brick and other modern produc...

  17. Enhancement in thermal and mechanical properties of bricks

    Directory of Open Access Journals (Sweden)

    Shibib Khalid S.

    2013-01-01

    Full Text Available A new type of porous brick is proposed. Sawdust is initially well mixed with wet clay in order to create voids inside the brick during the firing process. The voids will enhance the total performance of the brick due to the reduction of its density and thermal conductivity and a minor reduction of its compressive stress. All these properties have been measured experimentally and good performance has been obtained. Although a minor reduction in compressive stress has been observed with increased porosity, this property has still been larger than that of the common used hollow brick. Data obtained by this work lead to a new type of effective brick having a good performance with no possibility that mortar enters inside the holes which is the case with the common used hollow bricks. The mortar has a determent effect on thermal properties of the wall since it has some higher thermal conductivity and density than that of brick which increases the wall overall density and thermal conductivity of the wall.

  18. Drying brick masonry by electro-osmosis

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Rörig-Dalgaard, Inge

    2006-01-01

    When a fine grained, porous medium is applied an electric DC field, transport of matter occurs, and the transport mechanism in focus of the present study is electro-osmosis, which is transport of water. In laboratory it was shown possible to transport water inside a brick and brick/mortar system...... in an applied electric field. Electrodes have been constructed and placed inside an old house with moisture problems from capillary rise of water. The water content of the experimental wall was about 14%(weight). The electro-osmotic effect was even more pronounced here than in the in the laboratory, and a clear...... movement of water towards the cathode was seen. Thus the basis for utilizing the electro-osmotic effect for drying brick masonry is present, but proper electrodes still needs to be developed....

  19. New electrical tomographic method to determine dampness in historical buildings

    Directory of Open Access Journals (Sweden)

    Rymarczyk Tomasz

    2016-06-01

    Full Text Available This paper presents a new, nondestructive method of testing brick wall dampness in wall structures. The setup was used to determine the moisture in a specially built laboratory model. Topological methods and the gradient technique are used to optimize the approach. A forward model of a wall was constructed to solve the inverse problem resulting in moisture buildup inside the wall.

  20. Engineering BioBrick vectors from BioBrick parts

    Directory of Open Access Journals (Sweden)

    Knight Thomas F

    2008-04-01

    Full Text Available Abstract Background The underlying goal of synthetic biology is to make the process of engineering biological systems easier. Recent work has focused on defining and developing standard biological parts. The technical standard that has gained the most traction in the synthetic biology community is the BioBrick standard for physical composition of genetic parts. Parts that conform to the BioBrick assembly standard are BioBrick standard biological parts. To date, over 2,000 BioBrick parts have been contributed to, and are available from, the Registry of Standard Biological Parts. Results Here we extended the same advantages of BioBrick standard biological parts to the plasmid-based vectors that are used to provide and propagate BioBrick parts. We developed a process for engineering BioBrick vectors from BioBrick parts. We designed a new set of BioBrick parts that encode many useful vector functions. We combined the new parts to make a BioBrick base vector that facilitates BioBrick vector construction. We demonstrated the utility of the process by constructing seven new BioBrick vectors. We also successfully used the resulting vectors to assemble and propagate other BioBrick standard biological parts. Conclusion We extended the principles of part reuse and standardization to BioBrick vectors. As a result, myriad new BioBrick vectors can be readily produced from all existing and newly designed BioBrick parts. We invite the synthetic biology community to (1 use the process to make and share new BioBrick vectors; (2 expand the current collection of BioBrick vector parts; and (3 characterize and improve the available collection of BioBrick vector parts.

  1. Clay and concrete brick

    CSIR Research Space (South Africa)

    Dlamini, MN

    2014-03-01

    Full Text Available are manufactured from raw clay as their primary ingredient. However concrete brick has also become a favoured material in recent times. This review will adumbrate the impact of these building materials on energy use and the environment....

  2. A new method of preparing single-walled carbon nanotubes

    OpenAIRE

    Vivekchang, SRC; Govindaraj, A.

    2003-01-01

    A novel method of purification for single-walled carbon nanotubes, prepared by an arc-discharge method, is described. The method involves a combination of acid washing followed by high temperature hydrogen treatment to remove the metal nanoparticles and amorphous carbon present in the as-synthesized single-walled carbon nanotubes. The purified single-walled carbon nanotubes have been characterised by low-angle X-ray diffraction, electron microscopy, thermo-gravimetric analysis and Raman spect...

  3. COMPREHENSIVE DESIGN METHOD OF FREEZE WALL AND ITS APPLICATION

    Institute of Scientific and Technical Information of China (English)

    CHENXiangsheng

    1995-01-01

    Artificially ground freezing (AGF) is one of the main methods to establish temporary support for shaft sinking in unstable water bearing strata. Domke(1915) formula based on frozen soil strength has widely been used for designing freeze wall thickness. However, it can not ensure the stability of freeze wall, nor guarantee the safety of shaft construction as frozen depth increase in unstable water bearing strata. F.A.Auld (1985, 1988) presented a design method of freeze wall, which is on the basis of strength and stability, together with deformation of freeze wall.He combined deformation of freeze wall, lining and deformation of freeze tube to set up a comprehensive design method for freeze wall. This paper, according to the practice in China, describes a comprehensive design method for deep freeze wall, considering influence of excavation rate of advance, unsupported length of freeze wall and the sump state on inward deformation of freeze wall, and the allowable pipe deformation caused by inward deformation of freeze wall. Finally, successful application of this method to the large scale coal mine-Jining No.2 Mine in Shandong Province of China, is presented.It saved much investment compared with F.A.Auld's design for the same mine on behalf of Shell Coal International.

  4. Solar conduction heat transfer in fired clay bricks

    Energy Technology Data Exchange (ETDEWEB)

    Custodio-Garcia, E.; Andres Zarate, Esteban; Cordova, Quintiliano A. [Universidad Juarez Autonoma de Tabasco, DACB, Cunduacan, Tabasco 86680 (Mexico); Sebastian, P.J.; Campos-Alvarez, J. [CIE-UNAM, 62580 Temixco, Mor 62580 (Mexico); Trevino-Palacios, Carlos G. [Instituto Nacional de Astrofisica, Optica y Electronica. A.P. 51 Y 216. Puebla 72000 (Mexico); De la O-Leon, Hugo [Universidad Juarez Autonoma de Tabasco, DAIS, Cunduacan Tab (Mexico)

    2005-07-15

    When somebody is interested in building a house in the year-round-hot and humid regions, faces with the decision of using modern construction block material or the traditional red fired clay brick material. We performed mechanical and thermal controlled measurements on walls made using both materials. We found that the ancient tradition of using fired clay bricks, for the weather conditions in central Tabasco, represents an excellent alternative in cost and energy savings for construction.

  5. 贯入法与回弹法检测空斗墙砌体的适用性检验%Applicability verification of penetration method and rebound method testing row-lock cavity wall masonry

    Institute of Scientific and Technical Information of China (English)

    王卓琳

    2012-01-01

    In light of many row-lock cavity wall structures in villages and small towns of domestic Jiangnan region, the paper testifies the applica- bility of penetration method and rebound method for testifying the mortar of row-lock cavity wall and the masonry strength. Results show that pene- tration method is suitable to testify the mortar strength of row-lock cavity wall, and the testing position is good for avoiding cavity brick and lime joints. Rebound method is suitable to testify the clay strength of row-lock cavity wall masonry, and the testing position is good for avoiding cavity brick.%针对我国江南地区村镇较多的空斗墙结构,对贯入法和回弹法对空斗墙中砂浆和砌块强度检测的适用性进行了检验,结果表明,贯入法适用于空斗墙砌体砂浆强度的检测,检测位置宜避开斗砖和丁砖位置的灰缝,回弹法适用于空斗墙砌体粘土砖强度的检测,检测位置宜避开斗砖。

  6. Engineering BioBrick vectors from BioBrick parts

    OpenAIRE

    Knight Thomas F; Endy Drew; Shetty Reshma P

    2008-01-01

    Abstract Background The underlying goal of synthetic biology is to make the process of engineering biological systems easier. Recent work has focused on defining and developing standard biological parts. The technical standard that has gained the most traction in the synthetic biology community is the BioBrick standard for physical composition of genetic parts. Parts that conform to the BioBrick assembly standard are BioBrick standard biological parts. To date, over 2,000 BioBrick parts have ...

  7. Residential mercury contamination in adobe brick homes in Huancavelica, Peru.

    Directory of Open Access Journals (Sweden)

    Nicole Hagan

    Full Text Available This is the first study of adobe brick contamination anywhere in the world. Huancavelica, Peru is the site of historic cinnabar refining and one of the most mercury (Hg contaminated urban areas in the world. Over 80% of homes in Huancavelica are constructed with adobe bricks made from Hg contaminated soil. In this study we measured total Hg concentrations in adobe brick, dirt floor, surface dust, and air samples from the interior of 60 adobe brick houses located in four neighborhoods. Concentrations of total Hg in adobe bricks, dirt floors, and surface dust ranged from 8.00 to 1070 µg/g, 3.06 to 926 µg/g, and 0.02 to 9.69 µg/wipe, respectively, with statistically significant differences between the four neighborhoods. Concentrations of Hg in adobe brick and dirt floor samples in Huancavelica were orders of magnitude higher than in Ayacucho, a non-mining town in Peru. A strong correlation exists between total Hg concentrations in adobe bricks and dirt floors which confirms that adobe bricks were being made on-site and not purchased from an off-site source. A strong correlation between surface dust and adobe bricks and dirt floors indicates that walls and floors serve as indoor sources of Hg contamination. Elemental Hg vapor concentrations were below detection (<0.5 µg/m(3 in most homes; however in homes with detectable levels, concentrations up to 5.1 µg/m(3 were observed. No statistically significant differences in Hg vapor measurements were observed between neighborhoods. This study demonstrates that building materials used widely in developing communities, such as adobe bricks, may be a substantial source of residential Hg exposure in silver or gold refining communities where Hg is produced or used for amalgamation in artisanal gold production.

  8. Residential Mercury Contamination in Adobe Brick Homes in Huancavelica, Peru

    Science.gov (United States)

    Hagan, Nicole; Robins, Nicholas; Hsu-Kim, Heileen; Halabi, Susan; Espinoza Gonzales, Ruben Dario; Richter, Daniel deB.; Vandenberg, John

    2013-01-01

    This is the first study of adobe brick contamination anywhere in the world. Huancavelica, Peru is the site of historic cinnabar refining and one of the most mercury (Hg) contaminated urban areas in the world. Over 80% of homes in Huancavelica are constructed with adobe bricks made from Hg contaminated soil. In this study we measured total Hg concentrations in adobe brick, dirt floor, surface dust, and air samples from the interior of 60 adobe brick houses located in four neighborhoods. Concentrations of total Hg in adobe bricks, dirt floors, and surface dust ranged from 8.00 to 1070 µg/g, 3.06 to 926 µg/g, and 0.02 to 9.69 µg/wipe, respectively, with statistically significant differences between the four neighborhoods. Concentrations of Hg in adobe brick and dirt floor samples in Huancavelica were orders of magnitude higher than in Ayacucho, a non-mining town in Peru. A strong correlation exists between total Hg concentrations in adobe bricks and dirt floors which confirms that adobe bricks were being made on-site and not purchased from an off-site source. A strong correlation between surface dust and adobe bricks and dirt floors indicates that walls and floors serve as indoor sources of Hg contamination. Elemental Hg vapor concentrations were below detection (<0.5 µg/m3) in most homes; however in homes with detectable levels, concentrations up to 5.1 µg/m3 were observed. No statistically significant differences in Hg vapor measurements were observed between neighborhoods. This study demonstrates that building materials used widely in developing communities, such as adobe bricks, may be a substantial source of residential Hg exposure in silver or gold refining communities where Hg is produced or used for amalgamation in artisanal gold production. PMID:24040399

  9. Critical wall shear stress for the EHEDG test method

    DEFF Research Database (Denmark)

    Jensen, Bo Boye Busk; Friis, Alan

    2004-01-01

    In order to simulate the results of practical cleaning tests on closed processing equipment, based on wall shear stress predicted by computational fluid dynamics, a critical wall shear stress is required for that particular cleaning method. This work presents investigations that provide a critical...... wall shear stress of 3 Pa for the standardised EHEDG cleaning test method. The cleaning tests were performed on a test disc placed in a radial flowcell assay. Turbulent flow conditions were generated and the corresponding wall shear stresses were predicted from CFD simulations. Combining wall shear...... stress predictions from a simulation using the low Re k-epsilon and one using the two-layer model of Norris and Reynolds were found to produce reliable predictions compared to empirical solutions for the ideal flow case. The comparison of wall shear stress curves predicted for the real RFC...

  10. Thermal environmental status testing and analysis of a typical brick-wall solar greenhouse in Tianjin%天津一种典型砖墙日光温室热环境现状的测试与分析

    Institute of Scientific and Technical Information of China (English)

    徐凡; 马承伟; 刘洋; 宋道林

    2013-01-01

    In this paper,we tested the thermal and humidity environmental status in a typical brick-wall solar greenhouse in Tianjin for two winters.The results showed that,daily mean temperature is around 10 ℃,the lowest value is 5.0 ℃ ; daily minimum temperature is 3.4-5.5 ℃ in January and the lowest value is 0.8 ℃,which may cause the crop chilling injury;night temperature indoor is lower and the lowest average night temperature is 2.5 ℃ from December to next February;the night temperature difference between indoor and outdoor is 10-15 ℃.The indoor daily average relative humidity is 66% in the daytime in January,however,the relative humidity is only 50% when soilless culture is used.The average relative humidity at night is high to 99% in all the testing time.Results from this study showed that solar greenhouse can supply proper environment to crops most of the time,but there is still exiting some abnormal conditions (always low temperature and high humidity).We advise to improve the environment performance of solar greenhouse by the following measures:enhance the sunlight transmission from the roof; ensure the solar radiation received by the north wall; advance the thermal insulation and heat storage performance of enclosure structures; improve ventilation and modify cultivation methods.%对天津一种典型的砖墙日光温室进行连续2个冬季的热湿环境现状测试.结果表明:日光温室内日平均气温大部分时间可维持在10℃左右,最冷时仅为5.0℃;日最低气温1月份平均为3.4~5.5℃,极端日最低气温为0.8℃,此温度持续过长则会造成植物的冷害;温室内夜间温度较低,12-02月份室内夜间平均气温最低仅2.5℃;夜间室内外温差为10~15℃.1月份室内白昼平均相对湿度为66%,当采用无土栽培时,湿度仅50%左右;夜间室内相对湿度在整个测试期间都高达99%.可见,日光温室温湿环境大多适宜植物的生长,但仍存在

  11. Methods for Gas Sensing with Single-Walled Carbon Nanotubes

    Science.gov (United States)

    Kaul, Anupama B. (Inventor)

    2013-01-01

    Methods for gas sensing with single-walled carbon nanotubes are described. The methods comprise biasing at least one carbon nanotube and exposing to a gas environment to detect variation in temperature as an electrical response.

  12. Spalling Resistant Bauxite Based Bricks for Cement Kiln

    Institute of Scientific and Technical Information of China (English)

    Zhang Xiaohui; Peng Xigao

    2011-01-01

    @@ 1.Scope This standard specifies the term,definition,classification,labeling,technical requirements,test methods,inspection rules,packing,marking,transportation,storage,and quality certificate of spalling resistant bauxite based bricks for cement kiln.This standard is applicable to the spalling resistant bauxite based bricks for cement kiln.

  13. Hamilton-Jacobi method for curved domain walls and cosmologies

    Science.gov (United States)

    Skenderis, Kostas; Townsend, Paul K.

    2006-12-01

    We use Hamiltonian methods to study curved domain walls and cosmologies. This leads naturally to first-order equations for all domain walls and cosmologies foliated by slices of maximal symmetry. For Minkowski and AdS-sliced domain walls (flat and closed FLRW cosmologies) we recover a recent result concerning their (pseudo)supersymmetry. We show how domain-wall stability is consistent with the instability of AdS vacua that violate the Breitenlohner-Freedman bound. We also explore the relationship to Hamilton-Jacobi theory and compute the wave-function of a 3-dimensional closed universe evolving towards de Sitter spacetime.

  14. Shear Tests and Calculation of Shear Resistance with the PC Program RFEM from Thin Partition Walls of Brick in Old Buildings

    Directory of Open Access Journals (Sweden)

    Korjenic Sinan

    2015-11-01

    Full Text Available This paper is about the shear capacity of partition walls in old buildings based on shear tests which were carried out under real conditions in an existing building. There were experiments conducted on different floors and in each case, the maximum recordable horizontal force and the horizontal displacement of the respective mortar were measured. At the same time material studies and material investigations were carried out in the laboratory. The material parameters were used for the calculation of the precise shear capacity of each joint. In the shear tests, the maximum displacement of a mortar joint was determined at a maximum of two to four millimetres. Furthermore, no direct linear relationship between the theoretical load (wall above it and the shear stress occurred could be detected in the analysis of the experiment, as it was previously assumed.

  15. A new method of preparing single-walled carbon nanotubes

    Indian Academy of Sciences (India)

    S R C Vivekchand; A Govindaraj

    2003-10-01

    A novel method of purification for single-walled carbon nanotubes, prepared by an arc-discharge method, is described. The method involves a combination of acid washing followed by high temperature hydrogen treatment to remove the metal nanoparticles and amorphous carbon present in the as-synthesized singlewalled carbon nanotubes. The purified single-walled carbon nanotubes have been characterised by low-angle X-ray diffraction, electron microscopy, thermo-gravimetric analysis and Raman spectroscopy.

  16. Clicks, Bricks and Spondulicks

    Science.gov (United States)

    Fisher, Kenn

    2003-01-01

    "Clicks, Bricks and Spondulicks" is the title of a seminar organised by PEB to examine the relationship between the built learning environment and information and communications technology (ICT), as well as cost implications. The meeting sought to determine whether educational buildings and ICT should continue to be seen as separate…

  17. Mud Brick Resilience

    DEFF Research Database (Denmark)

    Johannessen, Runa

    2012-01-01

    In the seemingly endless circle of demolition and illegal rebuilding hand-made mud bricks produced from the soil of contested territory become an act of resistance. In June 2011, the Palestinian village Fasayel encountered the Israeli military’s demolition of 21 of the village’s built structures....

  18. Mud Brick Resilience

    DEFF Research Database (Denmark)

    Johannessen, Runa

    2012-01-01

    In the seemingly endless circle of demolition and illegal rebuilding hand-made mud bricks produced from the soil of contested territory become an act of resistance. In June 2011, the Palestinian village Fasayel encountered the Israeli military’s demolition of 21 of the village’s built structures....

  19. The evaluation of the thermal behaviour of a mortar based brick masonry wall coated with TiO2 nanoparticles : an experimental assessment towards energy efficient buildings

    OpenAIRE

    Carneiro, Joaquim A. O.; Vasconcelos, Graça; Azevedo, Sofia; Jesus, Carlos; Palha, Carlos; Gomes, Nuno; Teixeira, Vasco

    2014-01-01

    The transfer of energy (in the form of heat) between the building and its surroundings affects its thermal performance. When a given building system is thermally inefficient it will require that the HVAC equipment will be in permanent activity, increasing the underlying energy costs. This work evaluates the influence of using a TiO2-coated plastering mortar in the thermal performance of a building wall model. The TiO2 aqueous solution was sprayed onto the mortar surface, in its fresh state, b...

  20. Prevalence of Brick Tea-Type Fluorosis in the Tibet Autonomous Region.

    Science.gov (United States)

    Fan, Zhipeng; Gao, Yanhui; Wang, Wei; Gong, Hongqiang; Guo, Min; Zhao, Shengcheng; Liu, Xuehui; Yu, Bing; Sun, Dianjun

    2016-01-01

    The prevalence of brick tea-type fluorosis is high in Tibet because of the habit of drinking brick tea in this region. Brick tea-type fluorosis has become an urgent public health problem in China. A cross-sectional survey was conducted to investigate prevalence of brick tea-type fluorosis in all districts of Tibet using a stratified cluster sampling method. Dental fluorosis in children aged 8-12 years and clinical skeletal fluorosis in adults were diagnosed according to the national criteria. A total of 423 children and 1320 adults participated in the study. Samples of drinking water, brick tea, brick tea infusion (or buttered tea), and urine were collected and measured for fluoride concentrations by the fluoride ion selective electrode method. The fluoride level in all but one of the brick tea samples was above the national standard. The average daily fluoride intake from drinking brick tea in all seven districts in Tibet was much higher than the national standard. The prevalence of dental fluorosis was 33.57%, and the prevalence of clinical skeletal fluorosis was 46.06%. The average daily fluoride intake from drinking brick tea (r = 0.292, P children (r = 0.134, P prevalence of brick tea-type fluorosis. Herdsmen had the highest fluoride exposure and the most severe skeletal fluorosis. Brick tea-type fluorosis in Tibet is more serious than in other parts of China. The altitude and occupational factors are important risk factors for brick tea-type fluorosis.

  1. Water vapor sorption hysteresis of ceramic bricks

    Science.gov (United States)

    Koronthalyova, Olga

    2016-07-01

    A quantification of the hysteretic effects and their thorough analysis was carried out for three types of ceramic bricks. Water vapor adsorption/desorption isotherms were measured by the standard desiccator method. The desorption measurements were carried out from capillary moisture content as well as from equilibrium moisture content corresponding to the relative humidity of 98 %. For all three tested types of bricks the hysteretic effects were present but their significance differed depending on the particular type of brick. Significant differences were noticed also in desorption curves determined from capillary moisture content and from equilibrium moisture content corresponding to the relative humidity of 98 %. Based on the measured data a possible correlation between pore structure parameters and noticed hysteretic effects as well as relevance of the open pore model are discussed. The obtained adsorption/desorption curves were approximated by an analytical relation.

  2. Design Method of Reinforced Concrete Shear Wall Using EBCS

    Directory of Open Access Journals (Sweden)

    Dr. Suresh Borra

    2015-03-01

    Full Text Available Concrete shear walls or structural walls are often used in multistory buildings to resist lateral loads such as wind, seismic and blast loads. Such walls are used when the frame system alone is insufficient or uneconomical to withstand all the lateral loads or when partition walls can be made load bearing, replacing columns and beams. The analysis and design of buildings with shear walls became simple using commercially available computer programs based on the finite element method (FEM and subsequent implementation of stress integration techniques to arrive at generalized forces (axial, shear, and moments. On the other hand, design engineers without such facilities or those with computer facilities lacking such features use simple method of analysis and design by taking the entire dimensions of the walls. This is done by considering the shear walls as wide columns of high moment of inertia and following the same procedure as for columns. The primary purpose of this paper is believed that structural engineers working in the analysis and design of highrise buildings will be benefited from the design shear wall by using EBCS: 2-1995 and EBCS:8-1995codes and its results.

  3. 利用电厂粉煤灰制备蒸养标准砖%Preparation of Standard Brick with Coal Ash of Power Plant by Steam Curing Method

    Institute of Scientific and Technical Information of China (English)

    荣令坤; 张金山; 赵俊梅

    2011-01-01

    利用包头地区电厂粉煤灰、少量水泥、河砂,在碱性复合激发剂存在的情况下通过湿热养护工艺制成承重标准砖.试验采用单因索试验设计,得到粉煤灰掺量58.3%的粉煤灰砖,湿热养护28 d抗压强度18.7 MPa,抗折强度3.4 MPa.对影响砖体强度的几个主要因素进行了分析.%The load-bearing standard brick was prepared by coal ash from a power plant of Baotou by wet thermo-curing method under alkaline compound activator, with addition of small quantity of cement and river sand. Through the singlefactor experiments,the bricks with fly ash contents of up to 58.3% were obtained and its compressive strength of the brick reached 18.7 MPa,and bending strength 3.4 MPa at thermo-curing of 28 d. Then,some factors influencing the hardness of the brick were analyzed.

  4. Preservation of murals with electrokinetic - with focus on desalination of single bricks

    DEFF Research Database (Denmark)

    Rörig-Dalgaard, Inge

    2009-01-01

    Salt induced deterioration of murals is in several cases ongoing in Danish churches. The murals are one of the main objects of our Danish Cultural Heritage. Existing applied methods for desalination of salt contaminated church vaults are based on indirect affection of the dissolved salts (ions...... was developed to optimize the desalination effect. After improvement of the poultice, desalination from high and problematic ion content could be reduced to low and unproblematic ion content in single bricks. A patent application was handed in April 2008 and an international PCT patent application has recently...... followed. Besides the experiments on optimized laboratory setups the very first desalination of a wall section with murals was documented. In addition it was shown that the specific brick type and its pore system influences the electrochemical iontransport and coherence between the ion content in the pore...

  5. Four 3D "brick-wall"-like metal-organic frameworks with a flexible ligand of (S,S,R,R)-1,2,3,4-cyclopentanetetracarboxylic acid: crystal structures, luminescent and magnetic properties.

    Science.gov (United States)

    Cui, Lin; Luan, Xin-Jun; Zhang, Cui-Ping; Kang, Yi-Fan; Zhang, Wen-Tao; Wang, Yao-Yu; Shi, Qi-Zhen

    2013-02-01

    To investigate the conformation of cyclopentanetetracarboxylic acid, four new "brick-wall"-like metal-organic frameworks have been synthesized from hydrothermal reactions with different metal salts, (S,S,R,R)-1,2,3,4-cyclopentanetetracarboxylic acid (H(4)cptc) and auxiliary N-donor ligands, namely, Cu(2)(S,S,R,R-cptc)(bpe)(H(2)O)(2)·2H(2)O (1), Co(2)(S,S,R,R-cptc)(bpe)(0.5)(H(2)O)(2)·2H(2)O (2), Cd(4)(S,S,R,R-cptc)(2)(bpa)(2)(H(2)O)(5)·2H(2)O (3) and Co(2)(S,S,R,R-cptc)(bpy)(0.5)(H(2)O)(2)·2(H(2)O) (4) (bpe = 4-(2-(pyridine-4-yl)vinyl)pyridine, bpa = 4-(2-(pyridine-4-yl)ethyl)pyridine, bpy = 4-(pyridine-4-yl)pyridine). The complexes were further characterized by single-crystal X-ray diffraction, power X-ray diffraction, FT-IR spectra, fluorescent measurements and variable-temperature magnetic susceptibility measurements. The results of the structural investigations show that 1 is a charming (3,3,4)-trinodal architecture, 3 is an interesting trinodal (3,4,5)-connected architecture, and 2 and 4 are isostructural, which are both (4,5)-connected networks. In addition, the magnetic measurements indicate that 2 and 4 show weak antiferromagnetic interactions, and the fluorescent measurement shows the strong solid-state fluorescent emission at room temperature for 3.

  6. Architectural Thermal Forms II: Brick Envelope

    DEFF Research Database (Denmark)

    Foged, Isak Worre

    2013-01-01

    The paper presents an architectural concept and design method that investigates the use of dynamic factors in evolutionary form finding processes. The architectural construct, phenotype, is based on a brick assembly and how this can be organized based upon material properties and environmental...

  7. Architectural Thermal Forms II: Brick Envelope

    DEFF Research Database (Denmark)

    Foged, Isak Worre

    2013-01-01

    The paper presents an architectural concept and design method that investigates the use of dynamic factors in evolutionary form finding processes. The architectural construct, phenotype, is based on a brick assembly and how this can be organized based upon material properties and environmental...

  8. The Brick Moon

    Science.gov (United States)

    2004-01-01

    Science fiction writers, like Jules Verne in France and Edward Everett Hale in America, had discovered one of the most vital elements in the formula for space travel-a fertile imagination. The first known proposal for a marned-satellite appears in a story by Hale entitled 'The Brick Moon' published in 1899. The story involved a group of young Bostonians who planned to put an artificial satellite into polar orbit for sailors to use to determine longitude accurately and easily. They planned to send a brick satellite into orbit because the satellite would have to withstand fire very well. The Satellite's 37 inhabitants signaled the Earth in morse code by jumping up and down on the outside of the satellite.

  9. The Brick Moon

    Science.gov (United States)

    2004-01-01

    Science fiction writers, like Jules Verne in France and Edward Everett Hale in America, had discovered one of the most vital elements in the formula for space travel-a fertile imagination. The first known proposal for a marned-satellite appears in a story by Hale entitled 'The Brick Moon' published in 1899. The story involved a group of young Bostonians who planned to put an artificial satellite into polar orbit for sailors to use to determine longitude accurately and easily. They planned to send a brick satellite into orbit because the satellite would have to withstand fire very well. The Satellite's 37 inhabitants signaled the Earth in morse code by jumping up and down on the outside of the satellite.

  10. Wall Art

    Science.gov (United States)

    McGinley, Connie Q.

    2004-01-01

    The author of this article, an art teacher at Monarch High School in Louisville, Colorado, describes how her experience teaching in a new school presented an exciting visual challenge for an art teacher--monotonous brick walls just waiting for decoration. This school experienced only minimal instances of graffiti, but as an art teacher, she did…

  11. Method and apparatus for constructing an underground barrier wall structure

    Science.gov (United States)

    Dwyer, Brian P.; Stewart, Willis E.; Dwyer, Stephen F.

    2002-01-01

    A method and apparatus for constructing a underground barrier wall structure using a jet grout injector subassembly comprising a pair of primary nozzles and a plurality of secondary nozzles, the secondary nozzles having a smaller diameter than the primary nozzles, for injecting grout in directions other than the primary direction, which creates a barrier wall panel having a substantially uniform wall thickess. This invention addresses the problem of the weak "bow-tie" shape that is formed during conventional jet injection when using only a pair of primary nozzles. The improvement is accomplished by using at least four secondary nozzles, of smaller diameter, located on both sides of the primary nozzles. These additional secondary nozzles spray grout or permeable reactive materials in other directions optimized to fill in the thin regions of the bow-tie shape. The result is a panel with increased strength and substantially uniform wall thickness.

  12. BioBrick assembly standards and techniques and associated software tools.

    Science.gov (United States)

    Røkke, Gunvor; Korvald, Eirin; Pahr, Jarle; Oyås, Ove; Lale, Rahmi

    2014-01-01

    The BioBrick idea was developed to introduce the engineering principles of abstraction and standardization into synthetic biology. BioBricks are DNA sequences that serve a defined biological function and can be readily assembled with any other BioBrick parts to create new BioBricks with novel properties. In order to achieve this, several assembly standards can be used. Which assembly standards a BioBrick is compatible with, depends on the prefix and suffix sequences surrounding the part. In this chapter, five of the most common assembly standards will be described, as well as some of the most used assembly techniques, cloning procedures, and a presentation of the available software tools that can be used for deciding on the best method for assembling of different BioBricks, and searching for BioBrick parts in the Registry of Standard Biological Parts database.

  13. Wall shear stress measurement method based on parallel flow model near vascular wall in echography

    Science.gov (United States)

    Shimizu, Motochika; Tanaka, Tomohiko; Okada, Takashi; Seki, Yoshinori; Nishiyama, Tomohide

    2017-07-01

    A high-risk vessel of arteriosclerosis is detected by assessing wall shear stress (WSS), which is calculated from the distribution of velocity in a blood flow. A novel echographic method for measuring WSS, which aims to distinguish a normal vessel from a high-risk vessel, is proposed. To achieve this aim, the measurement error should be less than 28.8%. The proposed method is based on a flow model for the area near a vascular wall under a parallel-flow assumption to avoid the influences of error factors. This was verified by an in vitro experiment in which the WSS of a carotid artery phantom was measured. According to the experimental results, the WSS measured by the proposed method correlated with the ground truth measured by particle image velocimetry; in particular, the correlation coefficient and measurement error between them were respectively 0.70 and 27.4%. The proposed method achieved the target measurement performance.

  14. Monitoring Thermal Performance of Hollow Bricks with Different Cavity Fillers in Difference Climate Conditions

    Science.gov (United States)

    Pavlík, Zbyšek; Jerman, Miloš; Fořt, Jan; Černý, Robert

    2015-03-01

    Hollow brick blocks have found widespread use in the building industry during the last decades. The increasing requirements to the thermal insulation properties of building envelopes given by the national standards in Europe led the brick producers to reduce the production of common solid bricks. Brick blocks with more or less complex systems of internal cavities replaced the traditional bricks and became dominant on the building ceramics market. However, contrary to the solid bricks where the thermal conductivity can easily be measured by standard methods, the complex geometry of hollow brick blocks makes the application of common techniques impossible. In this paper, a steady-state technique utilizing a system of two climatic chambers separated by a connecting tunnel for sample positioning is used for the determination of the thermal conductivity, thermal resistance, and thermal transmittance ( U value) of hollow bricks with the cavities filled by air, two different types of mineral wool, polystyrene balls, and foam polyurethane. The particular brick block is provided with the necessary temperature- and heat-flux sensors and thermally insulated in the tunnel. In the climatic chambers, different temperatures are set. After steady-state conditions are established in the measuring system, the effective thermal properties of the brick block are calculated using the measured data. Experimental results show that the best results are achieved with hydrophilic mineral wool as a cavity filler; the worst performance exhibits the brick block with air-filled cavities.

  15. High Quality Silica Bricks for Glass Melting Furnace

    Institute of Scientific and Technical Information of China (English)

    Zhang Xiaohui; Chai Junlan

    2008-01-01

    @@ 1 Scope This standard specifies the classification, technical requirements, test method, inspection rules,marking,packing,transportation,storage and quality certification of high quality silica bricks for glass melting furnace.

  16. High Alumina Refractory Bricks for Electric Arc Furnace Roofs

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ 1 Scope This standard specifies the sort, technical requirement, test method, inspection rules, marking, packing, transportation, storage and quality certification of high alumina refractory bricks for electric arc furnace roofs.

  17. The Application of the Neutron Probe to the Study of Brick Deterioration.

    Science.gov (United States)

    Livingston, Richard Allan

    1990-01-01

    The neutron probe is a non-destructive method for measuring elemental distributions in materials. It measures the characteristic gamma rays emitted by the thermal capture of neutrons in the target material. In this case, it is applied to investigating the deterioration of brick and mortar masonry caused by water or chlorides. The research concerned the standardization of the technique to make it a quantitative analytical method. This consisted of finding the calibration function, and specifying a number of data quality parameters including precision accuracy and minimum level of detection for measurement of H and Cl. The work involved statistical analysis of the range of brick and mortar nuclear properties; mathematical modeling of neutron and gamma ray transport; experimental measurement of data quality parameters on a test wall in the laboratory; and ultimately a field test of the technique on a colonial smokehouse in Colonial Williamsburg. The results of the statistical analysis indicated that the neutron probe is insensitive to local variations of brick physical and chemical properties. The mathematical models showed that the presence of H increased the signal while Cl depressed it. The calibration function is linear when corrected for these effects. The most effective method of correction is normalization to the Si intensity. The precision of the technique is set primarily by the gamma ray counting statistics, and in this case, is better than 10%. The minimum level of detection for water is roughly 2% by weight, and for NaCL, lower than.1%. The conclusion is that this is a practical method for the non-destructive evaluation of brick deterioration.

  18. Water absorption in brick masonry

    NARCIS (Netherlands)

    Brocken, H.J.P.; Smolders, H.R.

    1996-01-01

    The water absorption in brick, mortar that was cured separately, and masonry samples was studied using NMR. Models of the moisture transport are usually formulated on the basis of a diffusion equation. In the case of water absorption in separate brick and mortar samples, the moisture diffusivity in

  19. More than Bricks and Mortar

    Science.gov (United States)

    Stanistreet, Paul

    2009-01-01

    Gaythorne Row, a terrace of Victorian back-to-back houses in Great Horton, was earmarked for demolition when, in 1986, Bradford Industrial Museum took possession of the three cottages and transported them, brick by brick, to the museum site four miles away. The houses were built in 1876, a year later than the old worsted spinning mill in which the…

  20. Use of Cement-Sand Admixture in Laterite Brick Production for Low Cost Housing

    Directory of Open Access Journals (Sweden)

    Isaac Olufemi AGBEDE

    2008-06-01

    Full Text Available Laterite was modified with 45% sand content by dry weight and stabilized with up to 9% cement content respectively and used in the production of 330 mm × 150 mm × 150 mm bricks through the application of a pressure of 3 N/mm2 with a brick moulding machine. Results showed that laterite used in this study cannot be stabilized for brick production within the economic cement content of 5% specified for use in Nigeria. However, bricks made with laterite admixed with 45% sand and 5% cement attained a compressive strength of 1.80 N/mm2 which is greater than the specified minimum strength value of 1.65 N/mm2. Cost comparison of available walling materials in Makurdi metropolis showed that the use of bricks made from 45% sand and 5% cement resulted in a saving of 30 - 47% when compared with the use of sandcrete blocks while the use of fired clay bricks resulted in a savings of 19% per square meter of wall. The study therefore recommends the use of laterite bricks in Makurdi and other locations because it is more economical and environmental friendly than fired clay bricks.

  1. A New Method of Hardening Inner Wall of Long Pipe

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A new laser inner wall hardening method for long pipe mas introduced. The system combines laser surface hardening with robot moving in pipeline. Some craft experiments have been done with this system and optimum parameters of laser hardening have been found.

  2. 《苏州城墙》:复活每一块城砖的历史记忆--以城墙为中心的吴文化巡礼%The City Walls of Suzhou:To Resurrect the Historical Memory of Each Block Bricks:A Survey of Wu Culrure Centering on City Walls

    Institute of Scientific and Technical Information of China (English)

    孙宗广

    2013-01-01

    The City Walls of Suzhou is not a ifrst book on city walls, but compared with similar studies home and abroad, this book, in addition to full and accurate data, pictures, has several prominent features:general size and tolerance, the pursuit of archaeology and measurement precision, highlight of the Wu culture. As for the protection of Suzhou city wall and rehabilitation, this book follows the principles of authenticity and integrity, rather than large-scale restoration and construction. The full collection and collation of literature on ancient city wall, the completion of archaeological and measuring work of the Suzhou ancient city wall ruins and the recovery of historical memory of every piece of brick, are supposed to go before the rehabilitation work. The publication of The City Walls of Suzhou is a remarkable step in all the above-mentioned solid work.%《苏州城墙》一书无意开城墙研究的风气之先,但与国内外的同类研究专著相比,该著除了资料翔实、图文并茂之外,具有几个突出特点:通史的规模与气度、追求考古与测量的精确、凸显吴文化的深厚底蕴。关于苏州城墙的保护与复建,该著认为应认真调研、循序渐进,遵循真实性和整体性原则,不必急于大规模复原与兴建。充分搜集整理古城墙的文献资料、完成苏州古城墙遗址的考古与测量、恢复每一块城砖的历史记忆,理应是走在复建前面的更为扎实有益的工作。《苏州城墙》的编著出版,便是这扎实工作中具有标志性的一步。

  3. Problem-Solving: Scaling the "Brick Wall"

    Science.gov (United States)

    Benson, Dave

    2011-01-01

    Across the primary and secondary phases, pupils are encouraged to use and apply their knowledge, skills, and understanding of mathematics to solve problems in a variety of forms, ranging from single-stage word problems to the challenge of extended rich tasks. Amongst many others, Cockcroft (1982) emphasised the importance and relevance of…

  4. Another four bricks in the wall

    Science.gov (United States)

    Burdette, Shawn C.; Ball, Philip; Day, Kat; Scerri, Eric R.; Thornton, Brett F.

    2016-04-01

    Of all the things humans can bestow names upon, new chemical elements are about the rarest. Our group of periodic table experts attempts to read the tea leaves and predict the names for elements 113, 115, 117 and 118.

  5. Silica Refractory Bricks for Glass Melting Furnace YB/T 147-1998

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ 1 Scope This standard specifies the classification, technical requirements, test method, inspection rules, marking, packing, transportation, storage and quality certification of silica refractory bricks for glass melting furnaces.

  6. Bauxite Based Refractory Bricks for Hot Blast Stove YB/T 5016-2000

    Institute of Scientific and Technical Information of China (English)

    Wang Jing; Chai Junlan

    2008-01-01

    @@ 1Scope This standard specifies the technical requirements, test method, inspection rules, packing, marking, transportation, storage and quality certificate of bauxite based refractory bricks for hot blast stove.

  7. NON-AUTOCLAVE SILICATE BRICK

    Directory of Open Access Journals (Sweden)

    V. N. Yaglov

    2015-01-01

    Full Text Available The paper proposes a technology for obtaining bricks on the basis of lime-silica mixtures where chemical interactions are practically completely realized in dispersive state at the stage of preparation of binding contact maturing and raw mixture as a whole. The role of forming operation (moulding is changed in principle because in this case conversion of dispersive system into a rock-like solid occurs and due to this the solid obtains complete water-resistance in contact with water immediately after forming operation. Theoretical basis for the developed technology is capability of silicate dispersive substances (hydrated calcium silicate to transit in non-stable state, to form a rock-like water-resistant solid in the moment of mechanical load application during forming process. Specific feature of the proposed method is an exclusion of additional operations for autoclaving of products from the process of obtaining a silicate brick.Synthetic hydrated calcium silicate in contrast to natural ones are more uniform in composition and structure, they contain less impurities and they are characterized by dispersive composition and due to the mentioned advantages they find wider practical application. Contact-condensation binders permit to manipulate product properties on their basis and ensure maximum correspondence to the requirements of the concrete application. Raw material sources for obtaining synthetic hydrated calcium silicates are practically un-limited because calcium-silicon containing substances are found as in various technogenic wastes so in natural compounds as well. So the problem for obtaining hydrated calcium silicates having contact-condensation ability for structure formation becomes more and more actual one. This transition is considered as dependent principally on arrangement rate of substance particles which determined the level of its instability.

  8. Cellular Concrete Bricks with Recycled Expanded Polystyrene Aggregate

    Directory of Open Access Journals (Sweden)

    Juan Bosco Hernández-Zaragoza

    2013-01-01

    Full Text Available Cellular concrete bricks were obtained by using a lightweight mortar with recycled expanded polystyrene aggregate instead of sandy materials. After determining the block properties (absorption, compressive strength, and tensile stresses, it was found that this brick meets the requirements of the masonry standards used in Mexico. The obtained material is lighter than the commercial ones, which facilitates their rapid elaboration, quality control, and transportation. It is less permeable, which helps prevent moisture formation retaining its strength due to the greater adherence shown with dry polystyrene. It was more flexible, which makes it less vulnerable to cracking walls due to soil displacements. Furthermore, it is economical, because it uses recyclable material and has properties that prevent deterioration increasing its useful life. We recommend the use of the fully dry EP under a dry environment to obtain the best properties of brick.

  9. Properties of Magnesia-Hercynite Brick

    Institute of Scientific and Technical Information of China (English)

    LIU Huilin

    2008-01-01

    Properties of magnesia-hercynite brick were studied. The coatability, thermal shock resistance, corrosion resistance to cement clinker and thermal conductivity were compared with those of magnesia-chrome brick and magnesia-spinel brick used widely in sintering zone of cement rotary kiln. The result shows that magnesia-hercynite brick is better than magnesia-chrome brick in thermal chock resistance and Corrosi on resistance to cement clinker, is similar to magnesia-chrome brick and is better than magnesia-spinel brick in coatability and thermal conductivity.

  10. Tangential stress analysis of myocardial wall by finite element method

    Institute of Scientific and Technical Information of China (English)

    Guan Qiu; Jiang Cao; Wang Xiaoyan; Chen Shengyong; Guan Fang

    2011-01-01

    A novel method is presented to build the triangular surface model and calculate the tangential stress and strain of myocardial wall ,which can be further used to reflect the left ventricle twisting-a sensitive index to assess the systolic and diastolic function of heart. Firstly, a point distribution model is used to obtain the feature points of the ventricular surface in medical images. Secondly, the surface model is constructed by triangular mesh, and then the subdivision strategy is introduced to refine the model. Thirdly, plane projection and finite element method ( FEM ) are applied to calculate the tangential stress and strain. Finally, the distribution of tangential modulus of elasticity is discussed. The stimulation results show that the proposed method can be used to compute the tangential stress and strain of myocardial wall effectively and the computing result is consistent with the results mentioned in the literatures.

  11. Effect of Peat on Physicomechanical Properties of Cemented Brick

    Directory of Open Access Journals (Sweden)

    Syed Mofachirul Islam

    2014-01-01

    Full Text Available The popularity of low cost, lightweight, and environmentally affable masonry unit in building industry carries the need to investigate more flexible and adaptable brick component as well as to retain the requirements confirmed in building standards. In this study, potential use of local materials used as lightweight building materials in solving the economic problems of housing has been investigated. Experimental studies on peat added bricks have been carried out. It demonstrates the physicomechanical properties of bricks and investigates the influence of peat, sand, and cement solid bricks to the role of various types of constructional applications. The achieved compressive strength, spitting strength, flexural strength, unit weight, and ultrasonic pulse velocity are significantly reduced and the water absorption is increased with percentage wise replacement of peat as aggregate in the samples. The maximum 20% of (% mass peat content meets the requirements of relevant well-known international standards. The experimental values illustrate that, the 44% volumetric replacement with peat did not exhibit any sudden brittle fracture even beyond the ultimate loads and a comparatively smooth surface is found. The application of peat as efficient brick substance shows a potential to be used for wall and a viable solution in the economic buildings design.

  12. Volume rendering acceleration method based on optimal bricking for large volume data%基于最优化分块的大规模数据体绘制加速方法

    Institute of Scientific and Technical Information of China (English)

    彭伟; 李建新; 闫镔; 童莉; 陈健; 管士勇

    2011-01-01

    GPU-based volume rendering has become an active research area in the domain of volume visualization.Large volume data cannot be uploaded directly due to the limitation of GPU memory, which has been a bottleneck of the application of GPU.Bricking method could not only solve this problem, but also maintain the quality of original volume-rendered image.However, the data exchange via the graphics bus is really time consuming and will definitely degrade the render performance.As for these difficulties, the optimal bricking for large volume data was calculated by establishing the model for optimal bricking, and also a 3D texture named node code texture was constructed and distance template was improved to accelerate the octree-based bricking volume rendering.The experimental results illustrate that the proposed method can significantly accelerate the bricking-based volume rendering for large volume data.%GPU加速体绘制已成为体可视化领域的研究热点,然而超出显存的大规模数据无法直接载入,成为GPU应用的瓶颈.分块技术能够在保证图像质量的条件下解决该问题,但分块数据的频繁加载和访问明显降低了绘制速度.针对上述问题,通过建立最优化分块模型得到了大规模数据的最优分块,并通过构造节点编号纹理和改进距离模板设计的方法进一步提高了基于八叉树的分块体绘制算法的绘制速度.实验结果表明,该方法加速效果明显.

  13. Controllable method for fabricating single-wall carbon nanotube tips

    Science.gov (United States)

    Zhang, Y.; Iijima, S.

    2000-08-01

    Single-wall carbon nanotubes (SWCNTs) were abruptly cut with a niobium substrate after a heating process in an ultrahigh vacuum transmission electron microscope. The cutting was attributed to a break of weakly bonded interface between carbon nanotubes and niobium carbide that formed as a product of a solid-phase reaction. This effect provided a controllable method for preparing well-defined SWCNT tips in future field-emission applications.

  14. Prevalence of Brick Tea-Type Fluorosis in the Tibet Autonomous Region

    OpenAIRE

    Zhipeng Fan

    2016-01-01

    Background: The prevalence of brick tea-type fluorosis is high in Tibet because of the habit of drinking brick tea in this region. Brick tea-type fluorosis has become an urgent public health problem in China. Methods: A cross-sectional survey was conducted to investigate prevalence of brick tea-type fluorosis in all districts of Tibet using a stratified cluster sampling method. Dental fluorosis in children aged 8–12 years and clinical skeletal fluorosis in adults were diagnosed according t...

  15. Theoretical analysis and experimental research of pull-out behavior of bonded steel bar embedded in brick wall of existing masonry structure%既有砌体结构墙体植筋拉拔性能的理论分析与试验研究

    Institute of Scientific and Technical Information of China (English)

    周彬; 吕西林; 任晓崧

    2012-01-01

    The brick wall is comprised of bricks and mortar. The strength of brick wall is low, so it is necessary to do some research on the mechanical property and the failure mode of steel bar embedded in the brick wall. In this paper, according to cone failure mode, shear failure mode and bond failure mode, the calculation formulas of the ultimate pull-out load are deduced. The semi-empirical simplification formula dependent on the strength of brick wall and the embedment depth, is also presented. Pull-out tests on steel bars with different dimension and depth were carried out in 8 masonry structures, which were different in the material strength and construction time. The finite element analysis (FEA) was also carried out. The results of pull-out test and FEA were compared to the results of theoretical analysis, which verified the rationality of the simplified formula. Some suggestions are presented as follows: the strength of mortar must be higher than M2.0, the suggested embedment depth is between 100 mm to 150 mm and the suggested diameters of steel bar are 6 ram, 8 mm and 10 ram.%砌体结构的材料强度较低且砖墙是由砖块与砂浆两种材料复合而成,将植筋技术应用于砌体结构尚未有深入研究。基于锥体破坏、剪切破坏与黏结破坏这三种破坏模式,推导了与植筋深度、墙体强度相关的植筋拉拔承载力的半经验简化计算式;利用8处不同类型的既有砌体结构,针对不同植筋直径、植筋深度进行现场拉拔试验;采用有限元数值分析,对砖墙的植筋拉拔性能进行分析,结合现场拉拔试验的结果,验证了半经验简化计算式的合理性。通过以上理论分析、现场试验,对植筋技术在砌体结构中的应用提出以下建议:在砌体结构中采用植筋,砖墙砂浆的抗压强度应大于M2.0;植筋的直径建议采用6 mm、8 mm或10 mm即可;植筋深度介于100 mm与150 mm之间。

  16. Perceptions on Barriers to the Use of Burnt Clay Bricks for Housing Construction

    Directory of Open Access Journals (Sweden)

    Bernard K. Baiden

    2014-01-01

    Full Text Available Burnt clay bricks can be readily manufactured in Ghana as all ten regions have significant clay deposits with the Ashanti region having the highest estimated deposit of 37.1 million metric tonnes. In recent times, burnt clay bricks have been regarded as old fashioned and replaced by other perceived modern walling units within Kumasi, the metropolitan capital of Ashanti Region, despite its availability, unique advantages (aesthetics, low maintenance cost, etc., and structural and nonstructural properties. This study involved a questionnaire survey of 85 respondents made up of architects, brick manufacturing firms, and brick house owners or occupants in the Kumasi Metropolis of Ghana and sought to examine their perceptions on barriers to the use of burnt clay bricks for housing construction. The findings revealed that the key factors inhibiting the use of burnt clay bricks for housing construction are low material demand, excessive cost implications, inappropriate use in construction, noncompatibility of burnt clay bricks with other materials, unreliable production, and transportation problems. The findings however provide a platform for stakeholders to address the barriers to enable the extensive use of clay bricks in housing constructions.

  17. 明清北京城墙砖珍稀图形款识初析%The Analysis Of Precious Moulage Of Brick Beijing City Wall In Ming Qing Dynasty

    Institute of Scientific and Technical Information of China (English)

    蔡青

    2016-01-01

    明清铭文城墙砖是建筑物料与文字结合的产物,是承载历史信息的珍贵实物史料。其中一些稀有的图形款识体现出特殊的历史文化意义,这些质朴、粗放的古代建筑物料借助其特有的艺术情趣传达着人们对吉祥、兴旺的美好向往。通过对铭文砖图形款识艺术文化内涵的分析和研究,能更清晰地展现出这些几乎被世间遗忘的文化元素特有的艺术魅力。%Ancient inscriptions of brick city wal is the combination of words and building of special building materials,politics,economy, culture, art is a record during the Ming and qing dynasties and the precious heritage of life information.In the brick city wal of the artistic appeal of rare graphical inscriptionshas the more rich significance These plain extensive ancient building materials. Convey the beautiful yearning for the auspicious and prosperous people.On the analysis of the inscription inscription art brick graphics cultural value and renew, Make these almost forgotten by the world of art element Show unique artistic charm.

  18. Monitoring Method for Blast Furnace Wall With Copper Staves

    Institute of Scientific and Technical Information of China (English)

    CHENG Su-sen; QIAN Liang; ZHAO Hong-bo

    2007-01-01

    A monitoring method that has been designed for the first time for blast furnace wall with copper staves manufactured in China was introduced. Combining the method of "inverse problem" and the concept "non-inverse problem", the monitoring program for blast furnace wall with copper staves has been realized, which can be used to calculate online the accretion thickness and temperature of hot surface of copper staves after obtaining the values of thermocouples of copper staves. The accretion state obtained in the actual investigation has proved that the result of the program is correct. The monitoring program shows that the accretion would easily fluctuate when the accretion layer is extremely thick or thin, thereby the stable and smooth operation of the blast furnace is hindered. By maintaining appropriate accretion thickness, both long campaigns and high productivity of the blast furnace can be achieved; furthermore, it can also optimize the operation of blast furnace and maximize its production. Approximately 30-50 mm in thickness of accretion layer is maintained on the wall of Shougang blast furnace 2, which can meet the requirement for obtaining both long campaign and high productivity.

  19. Prevalence of Brick Tea-Type Fluorosis in the Tibet Autonomous Region

    Science.gov (United States)

    Fan, Zhipeng; Gao, Yanhui; Wang, Wei; Gong, Hongqiang; Guo, Min; Zhao, Shengcheng; Liu, Xuehui; Yu, Bing; Sun, Dianjun

    2016-01-01

    Background The prevalence of brick tea-type fluorosis is high in Tibet because of the habit of drinking brick tea in this region. Brick tea-type fluorosis has become an urgent public health problem in China. Methods A cross-sectional survey was conducted to investigate prevalence of brick tea-type fluorosis in all districts of Tibet using a stratified cluster sampling method. Dental fluorosis in children aged 8–12 years and clinical skeletal fluorosis in adults were diagnosed according to the national criteria. A total of 423 children and 1320 adults participated in the study. Samples of drinking water, brick tea, brick tea infusion (or buttered tea), and urine were collected and measured for fluoride concentrations by the fluoride ion selective electrode method. Results The fluoride level in all but one of the brick tea samples was above the national standard. The average daily fluoride intake from drinking brick tea in all seven districts in Tibet was much higher than the national standard. The prevalence of dental fluorosis was 33.57%, and the prevalence of clinical skeletal fluorosis was 46.06%. The average daily fluoride intake from drinking brick tea (r = 0.292, P < 0.05), urine fluoride concentrations in children (r = 0.134, P < 0.05), urine fluoride concentrations in adults (r = 0.162, P < 0.05), and altitude (r = 0.276, P < 0.05) were positively correlated with the prevalence of brick tea-type fluorosis. Herdsmen had the highest fluoride exposure and the most severe skeletal fluorosis. Conclusions Brick tea-type fluorosis in Tibet is more serious than in other parts of China. The altitude and occupational factors are important risk factors for brick tea-type fluorosis. PMID:26499132

  20. Prevalence of Brick Tea-Type Fluorosis in the Tibet Autonomous Region

    Directory of Open Access Journals (Sweden)

    Zhipeng Fan

    2016-02-01

    Full Text Available Background: The prevalence of brick tea-type fluorosis is high in Tibet because of the habit of drinking brick tea in this region. Brick tea-type fluorosis has become an urgent public health problem in China. Methods: A cross-sectional survey was conducted to investigate prevalence of brick tea-type fluorosis in all districts of Tibet using a stratified cluster sampling method. Dental fluorosis in children aged 8–12 years and clinical skeletal fluorosis in adults were diagnosed according to the national criteria. A total of 423 children and 1320 adults participated in the study. Samples of drinking water, brick tea, brick tea infusion (or buttered tea, and urine were collected and measured for fluoride concentrations by the fluoride ion selective electrode method. Results: The fluoride level in all but one of the brick tea samples was above the national standard. The average daily fluoride intake from drinking brick tea in all seven districts in Tibet was much higher than the national standard. The prevalence of dental fluorosis was 33.57%, and the prevalence of clinical skeletal fluorosis was 46.06%. The average daily fluoride intake from drinking brick tea (r = 0.292, P < 0.05, urine fluoride concentrations in children (r = 0.134, P < 0.05, urine fluoride concentrations in adults (r = 0.162, P < 0.05, and altitude (r = 0.276, P < 0.05 were positively correlated with the prevalence of brick tea-type fluorosis. Herdsmen had the highest fluoride exposure and the most severe skeletal fluorosis. Conclusions: Brick tea-type fluorosis in Tibet is more serious than in other parts of China. The altitude and occupational factors are important risk factors for brick tea-type fluorosis.

  1. BURST EVENT DETECTION IN WALL TURBULENCE BY WVITA METHOD

    Institute of Scientific and Technical Information of China (English)

    Jiang Nan; Shu Wei; Wang Zhendong

    2000-01-01

    Wavelet Variable Interval Time Average(WVITA)is introduced as a method incorporating burst event detection in wall turbulence.Wavelet transform is performed to unfold the longitudinal fluctuating velocity time series measured in the near wall region of a turbulent boundary layer using hot-film anemometer.This unfolding is both in time and in space simultaneously.The splitted kinetic of the longitudinal fluctuating velocity time series among different scales is obtained by integrating the square of wavelet coefficient modulus over temporal space.The time scale that related to burst events in wall turbulence passing through the fixed probe is ascertained by maximum criterion of the kinetic energy evolution across scales.Wavelet transformed localized variance of the fluctuating velocity time series at the maximum kinetic scale is put forward instead of localized short time average variance in Variable Interval Time Average(VITA)scheme.The burst event detection result shows that WVITA scheme can avoid erroneous judgement and solve the grouping problem more effectively which is caused by VITA scheme itself and can not be avoided by adjusting the threshold level or changing the short time average interval.

  2. Thermal Performance of Hollow Clay Brick with Low Emissivity Treatment in Surface Enclosures

    OpenAIRE

    Roberto Fioretti; Paolo Principi

    2014-01-01

    External walls made with hollow clay brick or block are widely used for their thermal, acoustic and structural properties. However, the performance of the bricks frequently does not conform with the minimum legal requirements or the values required for high efficiency buildings, and for this reason, they need to be integrated with layers of thermal insulation. In this paper, the thermal behavior of hollow clay block with low emissivity treatment on the internal cavity surfaces has been invest...

  3. Magnetic inclination from Brazilian bricks and application to Archeomagnetic dating

    Science.gov (United States)

    Begnini, G. S.; Hartmann, G. A.; Trindade, R. I.

    2013-05-01

    The Earth's magnetic field (EMF) is recorded in archeological baked materials carrying a stable remanent magnetization. This magnetic record can be used for indirectly date the archeological material by comparison with "reference curves" of the EMF. In this work we present magnetic inclination data from two different sites in southeastern Brazil, an ancient and a modern one: (a) a sampling at the ancient sugarcane mill Engenho Central de Piracicaba (ECP, 1881-1974 AD), and (b) a controlled survey at the modern brickyard Olaria Schiavolin (OS). Both of them are located in the city of Piracicaba, São Paulo State, Brazil. Magnetic measurements included stepwise thermal and alternating field demagnetization, anisotropy of magnetic susceptibility (AMS) and low-field magnetic susceptibility vs. temperature. In OS, we collected 40 oriented bricks from 5 sampling points inside the brickyard oven in order to test the stability and reliability of their remanent magnetizations by comparing them with the local field (measured directly with a fluxgate magnetometer). We observed differences of +/- 3° between the local field and the IGRF. When magnetic inclinations are reported relative to the flat planes of the brick (the situation we face for real ancient bricks), the differences due to inclination of the burning plane and magnetic anomalies inside the oven never exceed 6°. These differences are averaged out by using a minimum of 6 bricks (~24 specimens) per sampling point to compute the inclination. In the ancient site ECP we collected 140 non-oriented bricks from 14 different walls; three of them were previously dated using historical records. Inclinations were defined using at least 6 bricks per wall, showing consistent average values within the same walls. When compared to the IGRF and GUFM1 models, the inclinations obtained for the dated walls agreed within the experimental error. We have then applied the same procedure to estimate the age of the remaining walls. Using

  4. Kaolinite Refractory Bricks for Blast Furnaces

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ This standard is suitable to the fireclay bricks for blast furnace. 1 Classification, Shape and Dimension 1 According to physical and chemical indexes, the brick can be divided into two trademarks: ZGN-42 and GN-42.

  5. Durability of compressed soil-cement bricks

    Directory of Open Access Journals (Sweden)

    Acosta Valle, A.

    2001-06-01

    Full Text Available This papers shows the evaluation process of the durability of compressed soil-cement bricks. A great number of tests were made to determine the behavior of bricks when they are compression loaded and under the influence of moisture. Two different types of soils were used to produce the bricks, a lime-clay soil and a sand one. The sand soil is very resistant. The other one has a limited use. An experimental design was used to test the bricks. It is a rotational and quadratic method with a hexagonal figure which contains replicas at the central point. This method ensures the reliability of test results. Otherwise, it would reduce the amount of specimens necessary for the tests. The optimun moisture content is obtained by using a press machine. It is more rational than the standard Proctor compactation test, because it applies the same type and amount of energy used to produce the bricks. The obtained results show the behavior differences between the two compressed soil-cement bricks subjected to the compression test, water absorption and wetting and drying tests. The durability tests results are very important in the possible use of the bricks produced.

    En el trabajo se evalúa la durabilidad de elementos aglomerados de suelo estabilizado. Se realiza un amplio número de ensayos encaminados a determinar el comportamiento frente a la acción de las cargas y la humedad de dos suelos con características diferentes: uno limo-arcilloso y el otro arenoso. Este último presenta resultados muy favorables en ambas direcciones. El otro, con un posible uso más limitado. Se emplea un método de diseño experimental del tipo rotacional cuadrático en hexágono, con réplicas en el punto central, el que garantiza la confiabilidad de los resultados de los ensayos, a la vez que disminuye la cantidad de especímenes a ensayar. Se determina la humedad óptima a utilizar en las diferentes dosificaciones empleando la máquina compactadora, que resulta m

  6. A Comprehensive Study on Gamma-Ray Exposure Build-Up Factors and Fast Neutron Removal Cross Sections of Fly-Ash Bricks

    Directory of Open Access Journals (Sweden)

    Vishwanath P. Singh

    2013-01-01

    Full Text Available Geometric progression (GP method was utilized to investigate gamma-ray exposure build-up factors of fly-ash bricks for energies from 0.015 to 15 MeV up to 40 mfp penetration depth. The EBFs of the fly-ash bricks are dependent upon the photon energy, penetration depths, and the chemical compositions of the elements. Appreciable variations in exposure build-up factor (EBF are noted for the fly-ash bricks. The EBFs were found to be small in low and high photon energy regions whereas very large in medium energy region. EBF of the bricks is inversely proportional to equivalent atomic number below 10 mfp for entire energy region of interest 0.015 to 15 MeV. The EBFs of fly-ash, brick of mud, and common brick were similar at 1.5 MeV photon energy. The EBF of the fly-ash bricks was found to be higher than that of the brick of mud, and common brick. The fast neutron removal cross sections of the fly-ash bricks, brick of mud, and common bricks were also calculated which were found to be in the same order. It is expected that this study should be very directly useful for shielding effectiveness of fly-ash brick materials and dose estimation.

  7. Can an Electron Rotate a Brick?

    Science.gov (United States)

    Bohren, Craig F.

    2009-01-01

    In "The Theory of Almost Everything", Robert Oerter asserts the following: "Take a beam of electrons that are all spinning in the same direction and fire it at, say, a brick. If you could keep this up for long enough, and if there were no other forces acting on the brick, the electrons would transfer their rotation to the brick, and it would begin…

  8. Sintered AZS Bricks for Glass Melting Furnace JC/T 925-2003

    Institute of Scientific and Technical Information of China (English)

    Yu Lingyan; Chai Junlan

    2009-01-01

    @@ 1 Scope This standard specifies the brand,technical requirements,test methods,inspection rules,marking,packing,transportation,storage,and quality certificate of sintered AZS bricks for glass melting furnace.This standard is applicable to sintered AZS bricks for glass melting furnace.

  9. Accelerated ageing in testing bricks used in the conservation of historic buildings

    Science.gov (United States)

    Pavlendová, Gabriela; Podoba, Rudolf; Baník, Ivan

    2014-11-01

    The effect of accelerated climate ageing on historical bricks in the laboratory is investigated in the paper. Differences in thermal properties are experimentally determined and studied before and after bricks exposure to climate ageing, which consists of 60 freeze-thaw cycles. For measuring thermal conductivity, diffusivity and specific heat, pulse method is used.

  10. Biosusceptibility of historical bricks from the Bač fortress: part I

    Directory of Open Access Journals (Sweden)

    Vidaković Ana M.

    2013-01-01

    Full Text Available The significance of the conservation of cultural heritage objects has led to a greater interest in the appearance of biocorrosion. The aim of this paper is to point out the correlation between the growth of fungi isolated from the fortress of Bač and the contact angle value of the bricks from the fortress in order to determine the brick susceptibility to biodegradation. Three types of bricks (red, yellow and roan and three isolates of Penicillium spp., as well as one isolate of Cladosporium sp., were used during the experiments. A suspension of fungi in soil extract solution was inflicted on the surface of the bricks and then the samples were incubated. The study showed that the red bricks with cut surface and the roan bricks with broken surface are the most susceptible to the biocorrosion process. Based on the obtained results, Cladosporium sp. can be considered as the most important biodeteriogenic factor on the bricks built in the walls of the Bač fortress. [Projekat Ministarstva nauke Republike Srbije, br. III45008

  11. A Method of Assembling Wall or Floor Elements

    DEFF Research Database (Denmark)

    2002-01-01

    The invention relates to a method of constructing, at the site of use, a building wall (1) or a building floor (1) using a plurality of prefabricated concrete or lightweight concrete plate-shaped wall of floor elements (10), in particular cast elements, which have a front side and a rear side...... as well as longitudinal side edges faces (12), wherein the elements (10), in a first step, are arranged at the site of use in mutual extension and then, in a second step, are connected with each other by means of at least one force-transferring device to form a tight connection. The invention...... is characterized in that a circular ring-shaped depression (20) is provided on the front side and/or the rear side of two adjoining elements (10) after the first step, said circular ring-shaped depression extending in the one as well as the other element (10), that the force-transferring device is a pipe (25...

  12. 砖混教室窗间墙不同构造条件下的破坏特点和抗震性能分析%Failure characteristics and seismic performance analysis of longitudinal wall between windows of brick-concrete masonry classroom buildings with different structural measures

    Institute of Scientific and Technical Information of China (English)

    吴昊; 赵世春; 张蓬勃; 许浒

    2012-01-01

    为了研究砖混教学楼窗间墙中构造柱的截面尺寸和配筋对纵向窗间墙破坏特点和抗震性能的影响,设计了5片缩尺纵墙试件,并通过低周反复加载试验对配置不同尺寸和配筋构造柱的墙体试件的破坏破坏形态、滞回特性、变形能力、刚度退化等进行了分析.结果表明,中柱的截面大小和配筋不改变墙体的破坏形态,各墙体试件均发生剪切破坏,按照规范要求设置构造柱的墙体试件表现出较好的抗震性能,构造柱与砖砌体具有较好的协同工作性能,适当增大构造柱截面尺寸能够显著改善墙体的延性耗能性能、变形能力,主裂缝宽度明显减小;增大中柱的配筋率使其成为RC柱时,尽管墙体试件抗侧刚度和承载力得到提高,但墙体的耗能能力和变形能力均出现降低,中柱与砖墙体的协同工作性能明显变差.因此,适当增大构造柱尺寸对于进一步提高砖混教学楼窗间墙的抗震和抗倒塌能力是有利的.%Five reduced-scale wall specimens were designed in order to investigate the influence of section size and reinforcement ratio of middle column on the failure characteristic and seismic performance of longitudinal wall between windows of brick-concrete school buildings. The failure characteristics, hysteretic behavior, deformability and stiffness degradation of each wall specimen were analyzed respectively. The results indicate that all specimens with different middle columns are characterized by shear failure. The specimen designed in accordance with the current code for seismic design generally exhibits good seismic performance where the structural column works well with brick masonry. Increasing section size of structural column can improve the energy dissipation, deformability and the crack distribution of specimen significantly. RC column decreases the energy dissipation and deformability of wall specimens in the highly nonlinear stage, although it can

  13. Experimental and analytical investigation of the lateral load response of confined masonry walls

    Directory of Open Access Journals (Sweden)

    Hussein Okail

    2016-04-01

    Full Text Available This paper investigates the behavior of confined masonry walls subjected to lateral loads. Six full-scale wall assembles, consisting of a clay masonry panel, two confining columns and a tie beam, were tested under a combination of vertical load and monotonic pushover up to failure. Wall panels had various configurations, namely, solid and perforated walls with window and door openings, variable longitudinal and transverse reinforcement ratios for the confining elements and different brick types, namely, cored clay and solid concrete masonry units. Key experimental results showed that the walls in general experienced a shear failure at the end of the lightly reinforced confining elements after the failure of the diagonal struts formed in the brick wall due to transversal diagonal tension. Stepped bed joint cracks formed in the masonry panel either diagonally or around the perforations. A numerical model was built using the finite element method and was validated in light of the experimental results. The model showed acceptable correlation and was used to conduct a thorough parametric study on various design configurations. The conducted parametric study involved the assessment of the load/displacement response for walls with different aspect ratios, axial load ratios, number of confining elements as well as the size and orientation of perforations. It was found that the strength of the bricks and the number of confining elements play a significant role in increasing the walls’ ultimate resistance and displacement ductility.

  14. 窗间墙锚固配筋砖混结构教学楼抗震性能试验研究%Experimental study on seismic performance of brick-concrete masonry school buildings with wall piers reinforced with anchored reinforcements

    Institute of Scientific and Technical Information of China (English)

    吴昊; 赵世春; 许浒; 张蓬勃; 吴刚

    2013-01-01

    Quasi-static tests on two half-scale two-story brick-concrete sub-structure models were carried out in order to improve the seismic performance of brick-concrete masonry school buildings. The wall piers between openings were partially reinforced with horizontal reinforcements that were reliably anchored using vertical reinforcements. The failure modes, load bearing capacity, deformability, rigidity degradation, ductility and hysteretic behavior of the two models, as well as failure modes of piers and failure mechanism of longitudinal walls were investigated. The results indicate that a story mechanism occurs in ordinary masonry model with the piers failing in shear failure. And the longitudinal walls exhibit strong spandrel-weak pier failure mechanism. However, partially reinforced wall piers are characterized by flexural failure with horizontal cracking in the mortar bed joints. Spandrels are severely damaged due to the formation of global failure mechanism. Strong pier-weak spandrel failure mechanism is guaranteed with uniform drift distribution. The level of damage, energy dissipation capacity and ductility of model are significantly improved.%为改善砖混结构教学楼的抗震性能,通过对其纵向窗间墙局部配筋并在墙体两端采用竖向钢筋进行锚固配筋,按照1/2的缩尺比例设计了2个砖混子结构模型.采用拟静力试验分别对普通窗间墙和配筋窗间墙的子结构模型的破坏模式、承载能力、变形能力、刚度退化、延性、耗能性能以及窗间墙的破坏模式和纵墙的破坏机制等进行了分析.结果表明:普通窗间墙模型表现为层间破坏机制,窗间墙发生剪切破坏,纵墙发生“强梁弱柱”式破坏;窗间墙局部配筋并进行锚固的模型发生整体型破坏,窗间墙弯曲破坏,纵墙的破坏机制具有“强柱弱梁”特征,层间变形均匀,模型的破坏形态、耗能能力和延性等均得到改善.

  15. Molecular mechanics of DNA bricks: in situ structure, mechanical properties and ionic conductivity

    Science.gov (United States)

    Slone, Scott Michael; Li, Chen-Yu; Yoo, Jejoong; Aksimentiev, Aleksei

    2016-05-01

    The DNA bricks method exploits self-assembly of short DNA fragments to produce custom three-dimensional objects with subnanometer precision. In contrast to DNA origami, the DNA brick method permits a variety of different structures to be realized using the same library of DNA strands. As a consequence of their design, however, assembled DNA brick structures have fewer interhelical connections in comparison to equivalent DNA origami structures. Although the overall shape of the DNA brick objects has been characterized and found to conform to the features of the target designs, the microscopic properties of DNA brick objects remain yet to be determined. Here, we use the all-atom molecular dynamics method to directly compare the structure, mechanical properties and ionic conductivity of DNA brick and DNA origami structures different only by internal connectivity of their consistituent DNA strands. In comparison to equivalent DNA origami structures, the DNA brick structures are found to be less rigid and less dense and have a larger cross-section area normal to the DNA helix direction. At the microscopic level, the junction in the DNA brick structures are found to be right-handed, similar to the structure of individual Holliday junctions (HJ) in solution, which contrasts with the left-handed structure of HJ in DNA origami. Subject to external electric field, a DNA brick plate is more leaky to ions than an equivalent DNA origami plate because of its lower density and larger cross-section area. Overall, our results indicate that the structures produced by the DNA brick method are fairly similar in their overall appearance to those created by the DNA origami method but are more compliant when subject to external forces, which likely is a consequence of their single crossover design.

  16. 3D Printing for Bricks

    OpenAIRE

    ECT Team, Purdue

    2015-01-01

    Building Bytes, by Brian Peters, is a project that uses desktop 3D printers to print bricks for architecture. Instead of using an expensive custom-made printer, it uses a normal standard 3D printer which is available for everyone and makes it more accessible and also easier for fabrication.

  17. Properties of bricks produced from Greenlandic marine sediments

    DEFF Research Database (Denmark)

    Bertelsen, Ida Maria Gieysztor; Belmonte, Louise Josefine; Chen, Wan

    2015-01-01

    This study investigated the possibility of a local brick production from fine grained marine sediments (MS) near Sisimiut, Greenland. The assessment is based on the physical and mechanical properties of clay bricks concerning the resistance to the harsh, Arctic weather conditions, together...... with an identification of a suitable production method. Samples of MS were collected near Sisimiut, Greenland, and tested with respect to the geological properties, which revealed a fine grained, low plasticity silty clay with evenly distributed grain sizes. By a screening of the mineralogy of MS by X-ray diffraction......, the major mineral phases were seen to be dominated by quarts and feldspar. Chemical investigations of MS showed low contents of both sulphur and carbon, whereas an unexpectedly high content of chlorine was found. A laboratory-scale study was made on fired brick pellets (d ∼20 mm, h ∼ 3 mm), and of fired...

  18. Desalination of painted brick vaults

    DEFF Research Database (Denmark)

    Larsen, Poul Klenz

    The subject of the thesis is salt and moisture movement that causes damage to wall paintings on church vaults. The deterioration was studied in the churches of Fanefjord, Kirkerup and Brarup. A desalination method was tested om location. The salt and moisture transfer was examined in detail...

  19. Desalination of painted brick vaults

    DEFF Research Database (Denmark)

    Larsen, Poul Klenz

    The subject of the thesis is salt and moisture movement that causes damage to wall paintings on church vaults. The deterioration was studied in the churches of Fanefjord, Kirkerup and Brarup. A desalination method was tested om location. The salt and moisture transfer was examined in detail...

  20. Excitonic AND Logic Gates on DNA Brick Nanobreadboards

    Science.gov (United States)

    2015-01-01

    A promising application of DNA self-assembly is the fabrication of chromophore-based excitonic devices. DNA brick assembly is a compelling method for creating programmable nanobreadboards on which chromophores may be rapidly and easily repositioned to prototype new excitonic devices, optimize device operation, and induce reversible switching. Using DNA nanobreadboards, we have demonstrated each of these functions through the construction and operation of two different excitonic AND logic gates. The modularity and high chromophore density achievable via this brick-based approach provide a viable path toward developing information processing and storage systems. PMID:25839049

  1. Excitonic AND Logic Gates on DNA Brick Nanobreadboards.

    Science.gov (United States)

    Cannon, Brittany L; Kellis, Donald L; Davis, Paul H; Lee, Jeunghoon; Kuang, Wan; Hughes, William L; Graugnard, Elton; Yurke, Bernard; Knowlton, William B

    2015-03-18

    A promising application of DNA self-assembly is the fabrication of chromophore-based excitonic devices. DNA brick assembly is a compelling method for creating programmable nanobreadboards on which chromophores may be rapidly and easily repositioned to prototype new excitonic devices, optimize device operation, and induce reversible switching. Using DNA nanobreadboards, we have demonstrated each of these functions through the construction and operation of two different excitonic AND logic gates. The modularity and high chromophore density achievable via this brick-based approach provide a viable path toward developing information processing and storage systems.

  2. Preparation and mechanism of the sintered bricks produced from Yellow River silt and red mud.

    Science.gov (United States)

    He, Hongtao; Yue, Qinyan; Su, Yuan; Gao, Baoyu; Gao, Yue; Wang, Jingzhou; Yu, Hui

    2012-02-15

    The preparation, characteristics and mechanisms of sintered bricks manufactured by Yellow River silt and red mud were studied. The sintering shrinkage, weight loss on ignition, water absorption and compressive strength were tested to determine the optimum preparation condition. Sintering mechanisms were discussed through linear regression analysis. Crystalline components of raw materials and bricks were analyzed by X-ray diffraction. Leaching toxicity of raw materials and bricks were measured according to sulphuric acid and nitric acid method. Radiation safety of the sintered bricks was characterized by calculating internal exposure index and external exposure index. The results showed that at the chosen best parameters (red mud content of 40%, sintering temperature of 1050°C and sintering time of 2h), the best characteristics of sintered bricks could be obtained. The weight loss on ignition of sintered bricks was principally caused by the removal of absorbed water and crystal water. The sintering shrinkage of sintered bricks mainly depended on sodium compounds and iron compounds of red mud. The sintering process made some components of raw materials transform into other crystals having better thermostability. Besides, the leaching toxicity and radioactivity index of sintered bricks produced under the optimum condition were all below standards.

  3. wall

    Directory of Open Access Journals (Sweden)

    Irshad Kashif

    2016-01-01

    Full Text Available Maintaining indoor climatic conditions of buildings compatible with the occupant comfort by consuming minimum energy, especially in a tropical climate becomes a challenging problem for researchers. This paper aims to investigate this problem by evaluating the effect of different kind of Photovoltaic Trombe wall system (PV-TW on thermal comfort, energy consumption and CO2 emission. A detailed simulation model of a single room building integrated with PV-TW was modelled using TRNSYS software. Results show that 14-35% PMV index and 26-38% PPD index reduces as system shifted from SPV-TW to DGPV-TW as compared to normal buildings. Thermal comfort indexes (PMV and PPD lie in the recommended range of ASHARE for both DPV-TW and DGPV-TW except for the few months when RH%, solar radiation intensity and ambient temperature were high. Moreover PVTW system significantly reduces energy consumption and CO2 emission of the building and also 2-4.8 °C of temperature differences between indoor and outdoor climate of building was examined.

  4. Investigation of kinetics of Cr(VI)-fired brick clay interaction.

    Science.gov (United States)

    Priyantha, Namal; Bandaranayaka, Anushka

    2011-04-15

    Fired brick clay is an excellent sorbent for the removal of heavy metal ions from waste water, owing to the availability of pores and interlayer spacing. Consequently, heat treatment of brick clay significantly affects the extent of interaction between the brick clay sorbent and adsorbates. The interaction between Cr(VI), available as Cr(2)O(7)(2-), and brick clay particles fired at temperatures between 200 °C and 600 °C follows pseudo second order kinetics, and the method of initial rates leads to the estimation of the average rate of the interaction process. Kinetics modeling suggests that the mass transfer of the interaction be mainly controlled by time-dependent intraparticle diffusion, as well as immobilization of Cr(VI) species within interlayer structure of the brick clay matrix and interparticle diffusion, both of which are time-independent.

  5. Reliability of using nondestructive tests to estimate compressive strength of building stones and bricks

    Directory of Open Access Journals (Sweden)

    Ali Abd Elhakam Aliabdo

    2012-09-01

    Full Text Available This study aims to investigate the relationships between Schmidt hardness rebound number (RN and ultrasonic pulse velocity (UPV versus compressive strength (fc of stones and bricks. Four types of rocks (marble, pink lime stone, white lime stone and basalt and two types of burned bricks and lime-sand bricks were studied. Linear and non-linear models were proposed. High correlations were found between RN and UPV versus compressive strength. Validation of proposed models was assessed using other specimens for each material. Linear models for each material showed good correlations than non-linear models. General model between RN and compressive strength of tested stones and bricks showed a high correlation with regression coefficient R2 value of 0.94. Estimation of compressive strength for the studied stones and bricks using their rebound number and ultrasonic pulse velocity in a combined method was generally more reliable than using rebound number or ultrasonic pulse velocity only.

  6. Corrosion Mechanism of Ladle Furnace Refining Slag to Fired MgO-CaO Bricks

    Institute of Scientific and Technical Information of China (English)

    ZHU Boquan; FANG Binxiang; ZHANG Wenjie; LI Xiangcheng; WAN Hongbo

    2010-01-01

    Corrosion effect of ladle furnace(LF)refining slag on fired MgO-CaO bricks with about 34% CaO was studied by static crucible method,and corrosion mechanism was analyzed by techniques of scan electron micrograph,energy dispersive spectrometer,and X-ray dif-fraction.The results show that: MgO-CaO bricks exhibit excellent corrosion resistance but poor penetration in reaction zone results in volume expansion forming MgO-CaO bricks increases liquid phases which accelerates corrosion of the bricks; a protective layer of 2CaO·SiO2 formed on reaction interface prevents penetration of C2F to the bricks.

  7. The Dynamic Similitude Design Method of Thin Walled Structures and Experimental Validation

    Directory of Open Access Journals (Sweden)

    Zhong Luo

    2016-01-01

    Full Text Available For the applicability of dynamic similitude models of thin walled structures, such as engine blades, turbine discs, and cylindrical shells, the dynamic similitude design of typical thin walled structures is investigated. The governing equation of typical thin walled structures is firstly unified, which guides to establishing dynamic scaling laws of typical thin walled structures. Based on the governing equation, geometrically complete scaling law of the typical thin walled structure is derived. In order to determine accurate distorted scaling laws of typical thin walled structures, three principles are proposed and theoretically proved by combining the sensitivity analysis and governing equation. Taking the thin walled annular plate as an example, geometrically complete and distorted scaling laws can be obtained based on the principles of determining dynamic scaling laws. Furthermore, the previous five orders’ accurate distorted scaling laws of thin walled annular plates are presented and numerically validated. Finally, the effectiveness of the similitude design method is validated by experimental annular plates.

  8. 氟离子选择电极法测定砖茶中氟含量的稳定性研究%Stability of fluoride ion selective electrode method to detect fluorine content in brick tea

    Institute of Scientific and Technical Information of China (English)

    李戎娟; 刘东娜; 李俊; 魏晓惠; 杜晓

    2013-01-01

    Objective To explore the stability of fluoride ion selective electrode method to detect fluorine content in brick tea, and provide theoretical data for its calibration. Methods Samples were extracted by boiling water, using TISAB buffer solution to eliminate the effect of interfering ions and acidity, and then measured by fluoride ion selective electrode. Results The factors had an obvious influence on the content of fluorine in brick tea, such as the buffer ionic strength, sample consumption, electrode, stirring speed, and filtra-tion condition. The detection of fluorine content in brick tea by using 120 g/L (TISAB-2) sodium citrate buffer solution were more accurate, and there was no significant difference in fluorine content between 120 g/L (TISAB-2) and 110 g/L (TISAB-GB) sodium citrate buffer solution. The fluorine content in 0.25 g samples reached the high value of 490.73±6.36 mg/kg, and this fluorine content was more accurate. The determination results showed that the new electrode was more stable than that by older electrode, the medium and high stir-ring speed were more stable and reliable than low stirring speed, and the qualitative filtration was much better than no filtration and quantitative filtration. Conclusion Under the optimum conditions, this method is accu-rate and stable, and it is suitable for the determination of fluorine content in brick tea.%  目的探讨氟离子选择电极法测定砖茶氟含量的稳定性,为该方法的校准提供理论数据。方法样品经沸水提取、缓冲溶液消除离子及酸度的干扰后,采用氟离子选择电极法测定砖茶试样中氟含量。结果缓冲溶液(TISAB)离子强度、试样用量、电极、搅拌速度、过滤条件等实验因素对样品氟含量测定结果影响极显著,其中以含柠檬酸钠120 g/L(TISAB-2)的缓冲液测定结果较准确,且与国标法(TISAB-GB)测定结果差异不显著;试样用量为0.25 g时,样品中氟含量值较高,为490.73±6.36 mg

  9. Refractory Behaviors of Magnetite-Kaolin Bricks

    Science.gov (United States)

    Adeosun, S. O.; Akpan, E. I.; Gbenebor, O. P.; Taiwo, O. O.; Eke, I. J.

    2016-11-01

    In this work, the suitability of using kaolin-magnetite-plastic clay to produce refractory bricks has been experimentally explored. Thirty bricks of different compositions were produced and fired at 1200°C. The density, shrinkage moisture content, loss on ignition, porosity and permeability of the bricks were examined. Results show that the bricks remained stable during firing and thus possess good insulating characteristics. The highest (2.23 g/cm3) and lowest (2.00 g/cm3) bulk densities obtained in this study are higher than the highest bulk density reported for Al dross-filled refractories (1.23 g/cm3). The bricks also possessed very low effective moisture content (10-23%) and very high compression modulus (16-100 MPa) desirable in insulating refractory bricks with high resistance to abrasion.

  10. Chromia refractory brick with carbon treatment

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, James P.; Kwong, Kyei-Sing

    2017-03-21

    The disclosure provides a refractory brick system comprising a chromia refractory brick for operation in the slagging environment of an air-cooled gasifier. The chromia refractory brick comprises a ceramically-bonded porous chromia refractory having a porosity greater than 9% and having carbon deposits residing within the pores. The brick may be further comprised of Al.sub.2O.sub.3. The air-cooled gasifier generates a liquefied slag in contact with the refractory brick and generally operates at temperatures between 1250.degree. C. and 1575.degree. C. and pressures between 300 psi to 1000 psi, with oxygen partial pressures generally between 10.sup.-4 and 10.sup.-10 atm. The refractory brick performs without substantial chromium carbide or chromium metal formation in the low oxygen partial pressure environment. The inclusion of carbon without chromium carbide formation provides for significant mitigation of slag penetration and significantly reduced refractory wear.

  11. Thermal control system and method for a passive solar storage wall

    Energy Technology Data Exchange (ETDEWEB)

    Ortega, J.K.E.

    1981-07-10

    A system and method are provided for controlling the storing and release of thermal energy from a thermal storage wall wherein said wall is capable of storing thermal energy from insolation. The system and method includes a device such as a plurality of louvers spaced a predetermined distance from the thermal wall for regulating the release of thermal energy from the thermal wall. This regulating device is made from a material which is substantially transparent to the incoming solar radiation so that when it is in any operative position, the thermal storage wall substantially receives all of the impacting solar radiation. The material in the regulating device is further capable of being substantially opaque to thermal energy so that when the device is substantially closed, thermal release of energy from the storage wall is substantially minimized. An adjustment device is interconnected with the regulating mechanism for selectively opening and closing it in order to regulate the release of thermal energy from the wall.

  12. Study of the geometry of a voided clay brick using rectangular perforations to optimize its thermal properties

    OpenAIRE

    Ortiz, M.P.; Juárez, M. C.; López-Ochoa, L.M.; Doménech, J.

    2011-01-01

    Abstract This study was undertaken to optimize the equivalent transmittance of a wall consisting of voided clay bricks using ceramic material Termoarcilla? 29 ECO, complying with the Spanish UNE [1], European EN [2] and international ISO [3], [4], [5], [6], [7] standards. Various geometries were investigated for the bricks' cross sections, starting from a commercialized block and improvements in its thermal conductivity were studied by varying parameters such as a number...

  13. Method of Calculation of Crown Wall Stability in Oblique Waves

    DEFF Research Database (Denmark)

    Burcharth, Hans F.

    2007-01-01

    The wave loading along a structure exposed to oblique waves varies in time and space. Despite of this, the wave generated pressures are usually recorded by gauges only in one position of the wall (more gauges densily spaced is regarded as one position).......The wave loading along a structure exposed to oblique waves varies in time and space. Despite of this, the wave generated pressures are usually recorded by gauges only in one position of the wall (more gauges densily spaced is regarded as one position)....

  14. High Alumina Brick

    Institute of Scientific and Technical Information of China (English)

    Zhang xiaohui

    2007-01-01

    @@ 1 Theme and Scope This standard specifies the classification,dimensions,technical requirement,testing method,inspection principle,package,marking,packing,transportation,storage and quality certificate.

  15. Effect of municipal solid waste ash on the strength of earthen bricks ...

    African Journals Online (AJOL)

    Journal of Agriculture, Science and Technology ... The soil used for making the bricks was stabilized using MSWA applied at the rate of 0%, 2%, 5% and ... The ultimate stress of the stabilized wall was 2.47N/mm2 occurring at a strain of 11.

  16. Low Porosity Fireclay Bricks for Glass Melting Furnace JC/T 638-1996

    Institute of Scientific and Technical Information of China (English)

    Zhang Xiaohui; Chai Junlan

    2008-01-01

    @@ 1Scope This standard specifies the classification, technical requirements, test methods, inspection rules, marking, packing, transportation, storage and quality certificate of low porosity fireclay bricks for glass melting furnace.

  17. The Effects of Non—Metal Additives on Hydration Reisitance of MgO—C Bricks

    Institute of Scientific and Technical Information of China (English)

    OUYAGNG; WANGRuikun; 等

    2000-01-01

    The general method of solving the problem of hydration of MgO-C brick is by adding with metal Si,Mg or compround metal additives,but metal additives have bad effect on the MgO-C brick,The test tried adding non-metal additives to matrix material.The results showed that a suitable amount of this kind of additives not only inhibits hydration of MgO-C brick and does not affect corrosion resistance and avoids thermal expansion,but also can improve oxidation resistance.

  18. Active thermal testing of moisture in bricks

    Science.gov (United States)

    Bison, Paolo G.; Bressan, Chiara; Grinzato, Ermanno G.; Marinetti, Sergio; Vavilov, Vladimir P.

    1993-04-01

    Measurement by active thermal testing of effusivity on porous moistened material is analyzed. Moistened bricks show that thermal properties of this porous solid depend on water content. Various solutions of the heat transfer problem are taken into account and approximations introduced to simplify the data reduction are discussed. Error analysis is also considered to justify the adoption of relative technique. Errors analysis speaks strongly in favor of reference method which allows to avoid the measurement of incident energy and optical properties of a specimen. This procedure allows to introduce a rather simple expression to extract moisture values from one-side thermal test. Diffusivity measurement trough flash method is proposed to determine the influence of moisture on the variation of thermal conductivity.

  19. Project Inner Brick - Colorful Plastic Bricks in Psychotherapy - An Introduction to Methodology

    Directory of Open Access Journals (Sweden)

    Neidert László

    2015-06-01

    Full Text Available PIB is a research project pertaining to the psychotherapeutic potential of Lego bricks. This is based on Lego Group’s own method called Lego Seriousplay and Eric Berne's transactional analysis as a theoretical background. If we see it from the Lego’s aspect, our plan is a training like LSP. It is only alike because of the special application. We made a lot of modifications according to the original methodology. In this document we would like to present details of our research we have been working on for almost two years. The characteristics of our methodology will be illustrated, too.

  20. Tests and Analysis of the Compressive Performance of an Integrated Masonry Structure of a Brick-Stem-Insulating Layer

    Directory of Open Access Journals (Sweden)

    Suizi Jia

    2016-05-01

    Full Text Available This paper proposes, for low buildings, an integrated wall structure of a brick-stem-insulating layer, which plays a major part in both heat preservation and force bearing. The research team has tested the thermal performance of the structure, the results of which are satisfying. To further study the force-bearing performance, the paper carries out compressive tests of specimens of different structural design, with two types of bricks, i.e., clay and recycled concrete bricks; three types of stems, i.e., square-shaped wood, square-shaped steel pipe and circular steel pipe; and one type of insulating layer, i.e., fly ash masonry blocks. Afterward, the force bearing performance, damage that occurred, compressive deformation and ductility of all of the specimens are compared. On the sideline, the structure is applied in the construction of a pilot residence project, yielding favorable outcomes. The results indicate that in comparison with a brick wall with an insulating layer sandwiched in between, the integrated wall structure of bricks and fly ash blocks is a more preferable choice in terms of compressive performance and ductility. The integrated wall structure of brick-stem-fly ash blocks delivers much better performance to this end. Note that regarding the stem’s contribution to compressive strength, circular steel pipe is highest, followed by square-shaped steel pipe and then square-shaped wood. The compressive performance of the sandwiched blocks surpasses that of the two brick wall pieces combined by a large margin.

  1. Modeling rammed earth wall using discrete element method

    Science.gov (United States)

    Bui, T.-T.; Bui, Q.-B.; Limam, A.; Morel, J.-C.

    2016-03-01

    Rammed earth is attracting renewed interest throughout the world thanks to its "green" characteristics in the context of sustainable development. Several research studies have thus recently been carried out to investigate this material. Some of them attempted to simulate the rammed earth's mechanical behavior by using analytical or numerical models. Most of these studies assumed that there was a perfect cohesion at the interface between earthen layers. This hypothesis proved to be acceptable for the case of vertical loading, but it could be questionable for horizontal loading. To address this problem, discrete element modeling seems to be relevant to simulate a rammed earth wall. To our knowledge, no research has been conducted thus far using discrete element modeling to study a rammed earth wall. This paper presents an assessment of the discrete element modeling's robustness for rammed earth walls. Firstly, a brief description of the discrete element modeling is presented. Then the parameters necessary for discrete element modeling of the material law of the earthen layers and their interfaces law following the Mohr-Coulomb model with a tension cut-off and post-peak softening were given. The relevance of the model and the material parameters were assessed by comparing them with experimental results from the literature. The results showed that, in the case of vertical loading, interfaces did not have an important effect. In the case of diagonal loading, model with interfaces produced better results. Interface characteristics can vary from 85 to 100% of the corresponding earthen layer's characteristics.

  2. Photovoltaic device using single wall carbon nanotubes and method of fabricating the same

    Science.gov (United States)

    Biris, Alexandru S.; Li, Zhongrui

    2012-11-06

    A photovoltaic device and methods for forming the same. In one embodiment, the photovoltaic device has a silicon substrate, and a film comprising a plurality of single wall carbon nanotubes disposed on the silicon substrate, wherein the plurality of single wall carbon nanotubes forms a plurality of heterojunctions with the silicon in the substrate.

  3. Chinese Standards on Refractories Shaped Insulating Refractory Product-High Alumina Bricks

    Institute of Scientific and Technical Information of China (English)

    Yu Lingyan

    2009-01-01

    @@ 1 Scope This standard specifies the classification,shape and dimension,technical requirements,test methods,quality appraisal procedure,packing,marking,transportation,storage,and quality certificate of high alumina insulating bricks. High alumina insulating bricks are used as working layer which contacts with fire directly,insulating layer,or inner lining of the kilns which does not react with the high temperature molten materials and corrosion gases.

  4. 21 CFR 133.109 - Brick cheese for manufacturing.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Brick cheese for manufacturing. 133.109 Section... Standardized Cheese and Related Products § 133.109 Brick cheese for manufacturing. Brick cheese for manufacturing conforms to the definition and standard of identity for brick cheese prescribed by § 133.108...

  5. An approximate method for lateral stability analysis of wall-frame buildings including shear deformations of walls

    Indian Academy of Sciences (India)

    Kanat Burak Bozdogan; Duygu Ozturk

    2010-06-01

    This study presents an approximate method based on the continuum approach and transfer matrix method for lateral stability analysis of buildings. In this method, the whole structure is idealized as an equivalent sandwich beam which includes all deformations. The effect of shear deformations of walls has been taken into consideration and incorporated in the formulation of the governing equations. Initially the stability differential equation of this equivalent sandwich beam is presented, and then shape functions for each storey is obtained by the solution of the differential equations. By using boundary conditions and stability storey transfer matrices obtained by shape functions, system buckling load can be calculated. To verify the presented method, four numerical examples have been solved. The results of the samples demonstrate the agreement between the presented method and the other methods given in the literature.

  6. Drying of brick as a function of heat flows and analysis of moisture and temperature distributions

    DEFF Research Database (Denmark)

    Svendsen, Sv Aa Højgaard; Rudbeck, Claus Christian; Bunch-Nielsen, Tommy

    1997-01-01

    In order to investigate the driving mechanisms for frost damages in brickwork, laboratory tests has been performed on a test brick wall. These test include monitoring of temperature and moisture distribution in the wall as function of the influence of driving rain, wind speed and solar radiation....... After the initial tests the surface of the wall was treated with mortar and a new series of test was performed. The wall with and without treatment performed almost equal during the influence of driving rain, and during the later drying phase, the difference was equally small....

  7. A view of microstructure with technological behavior of waste incorporated ceramic bricks

    Science.gov (United States)

    Nirmala, G.; Viruthagiri, G.

    2015-01-01

    Production of ceramic bricks from mixtures of ceramic industry wastes (up to 50 wt%) from the area of Vriddhachalam, Cuddalore district, Tamilnadu, India and kaolinitic clay from Thiruvananthapuram district, Kerala were investigated. The firing behavior of the ceramic mixtures was studied by determining their changes in mineralogy and basic ceramic properties such as water absorption, porosity, compressive strength and firing shrinkage at temperatures ranging from 900 to 1200 °C in short firing cycles. The effect of the rejects addition gradually up to 50 wt% was analyzed with the variation of temperature on the mechanical properties and microstructure of the bricks. The highest compressive strength and lowest water absorption is observed for the sample with 40% rejects at 1100 °C which is supported by the results of SEM analysis. The resulting ceramic bricks exhibit features that suggest possibilities of using the ceramic rejects in the conventional brick making methods.

  8. Moisture Research - Optimizing Wall Assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Arena, Lois [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Mantha, Pallavi [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2013-05-01

    In this project, the Consortium for Advanced Residential Buildings (CARB) team evaluated several different configurations of wall assemblies to determine the accuracy of moisture modeling and make recommendations to ensure durable, efficient assemblies. WUFI and THERM were used to model the hygrothermal and heat transfer characteristics of these walls. Wall assemblies evaluated included code minimum walls using spray foam insulation and fiberglass batts, high R-value walls at least 12 in. thick (R-40 and R-60 assemblies), and brick walls with interior insulation.

  9. Gamma-ray shielding effectiveness of novel light-weight clay-flyash bricks

    Science.gov (United States)

    Mann, Harjinder Singh; Brar, G. S.; Mudahar, G. S.

    2016-10-01

    The radiation shielding parameters of lightweight clay-flyash bricks produced with different flyash aggregate compositions have been investigated by using 241Am (59.4 keV), 137Cs (661.6 keV), and 60Co (1173.2 keV and 1332.5 keV) radioactive sources. It was observed that the different percentages of flyash in clay lead to significant variations in these parameters. The elemental compositions of the clay-flyash bricks were analyzed using energy dispersive X-ray fluorescence spectrometry (EDXRF). The obtained results were compared to those pertaining to concrete in order to see the effect of flyash content on the radiation shielding properties. The radiation protection efficiency of the tested clay-flyash bricks demonstrated that multilayer exterior walls built from these bricks could effectively attenuate moderate-energy gamma rays. Bricks using residual flyash could be preferentially used for buildings to address the issues of radiation shielding, cost-effective radioactive waste management and disposal of flyash in a useful manner.

  10. STRUCTURE AND PROPERTIES OF A CERAMIC BRICK MODIFIED WITH TECHNOGENIC MINERAL SYSTEMS

    Directory of Open Access Journals (Sweden)

    DEREVIANKO V. N.

    2016-07-01

    Full Text Available Summary. Problem statement. One way to conserve the scarce high-quality raw materials resources and to reduce transport and energy costs is to use the accumulated technogenic mineral systems, as well as to study technogenic raw materials which were not previously used [1-3]. A shortage of high plasticity clays determines the need for using local low-grade loamy raw materials for the manufacture of wall ceramics. Strength properties of the ceramic brick can be improved by using expensive corrective additives or local technogenic raw materials [4-7]. Purpose. Development of compositions for the ceramic brick, modified with technogenic mineral systems. Conclusion. The author has studied the influence of the mixture ratio on the structure and fundamental physical and mechanical properties of the ceramic brick modified with technogenic mineral systems. The author has also developed the best ceramic batch compositions based on technogenic mineral systems conferring the required physical and mechanical parameters of the ceramic brick; they consist of: overburden (67%, refuse heap (28% and red mud from NGZ (Mykolaiv Alumina Refinery (5% for making 150 Grade ceramic brick with an average density of 1,650-1,730 kg/m3 at a temperature of 850°C, which allows to reduce firing energy costs. It has been established that the sintering initiation temperature of the modified mixture decreases by 150-200°C compared to the unmodified one.

  11. Drying brick masonry by electro-osmosis

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Rörig-Dalgaard, Inge

    2006-01-01

    When a fine grained, porous medium is applied an electric DC field, transport of matter occurs, and the transport mechanism in focus of the present study is electro-osmosis, which is transport of water. In laboratory it was shown possible to transport water inside a brick and brick/mortar system...... movement of water towards the cathode was seen. Thus the basis for utilizing the electro-osmotic effect for drying brick masonry is present, but proper electrodes still needs to be developed....

  12. A method to quantitate regional wall motion in left ventriculography using Hildreth algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Terashima, Mikio [Hyogo Red Cross Blood Center (Japan); Naito, Hiroaki; Sato, Yoshinobu; Tamura, Shinichi; Kurosawa, Tsutomu

    1998-06-01

    Quantitative measurement of ventricular wall motion is indispensable for objective evaluation of cardiac function associated with coronary artery disease. We have modified the Hildreth`s algorithm to estimate excursions of the ventricular wall on left ventricular images yielded by various imaging techniques. Tagging cine-MRI was carried out on 7 healthy volunteers. The original Hildreth method, the modified Hildreth method and the centerline method were applied to the outlines of the images obtained, to estimate excursion of the left ventricular wall and regional shortening and to evaluate the accuracy of these methods when measuring these parameters, compared to the values of these parameters measured actually using the attached tags. The accuracy of the original Hildreth method was comparable to that of the centerline method, while the modified Hildreth method was significantly more accurate than the centerline method (P<0.05). Regional shortening as estimated using the modified Hildreth method differed less from the actually measured regional shortening than did the shortening estimated using the centerline method (P<0.05). The modified Hildreth method allowed reasonable estimation of left ventricular wall excursion in all cases where it was applied. These results indicate that when applied to left ventriculograms for ventricular wall motion analysis, the modified Hildreth method is more useful than the original Hildreth method. (author)

  13. Mechanical Properties of Unreinforced Brick Masonry, Section1

    Energy Technology Data Exchange (ETDEWEB)

    Mosalam, K; Glascoe, L; Bernier, J

    2009-10-02

    Before the advent of concrete and steel, masonry helped build civilizations. From Egypt in Africa, Rome in Europe, Maya in the America to China in Asia, masonry was exploited to construct the most significant, magnificent and long lasting structures on the Earth. Looking at the Egyptian pyramids, Mayan temples, Roman coliseum and Chinese Great Wall, one cannot stop wondering about the significance and popularity that masonry has had through out history. Lourenco et al (1989) summed up the reasons for the popularity of masonry in the following, 'The most important characteristic of masonry construction is its simplicity. Laying pieces of stone or bricks on top of each other, either with or without cohesion via mortar, is a simple, though adequate, technique that has been successful ever since remote ages. Other important characteristics are the aesthetics, solidity, durability, low maintenance, versatility, sound absorption and fire protection' Despite these advantages, masonry is no longer preferred structural material in many parts of the developed world, especially in seismically active parts of the world. Partly, masonry and especially unreinforced masonry (URM) has mechanical properties such as strength and ductility inferior to those of reinforced concrete and steel. Moreover, masonry structures were traditionally built based on rules of thumb acquired over many years of practice and/or empirical data from testing. Accordingly, we do not have a rigorous and uniform method of analysis and design for masonry. Nevertheless, the world still possesses numerous historic and ordinary masonry structures, which require maintenance and strengthening to combat the assault of time and nature. Hence, it is important to study fundamental properties of masonry so that new masonry structures can be effectively designed and built, and the cost for servicing old structures and for building new ones will be less expensive.

  14. Composition Analysis of Ancient Bricks, Candi Bukit Kechil, Bujang Valley, Kedah

    Directory of Open Access Journals (Sweden)

    Zuliskandar Ramli

    2013-06-01

    Full Text Available Candi Bukit Kechil or Bukit Kechil Temple is one of the temples in Bujang Valley that was built on a hill apart from Candi Bukit Pendiat (Site 17, Candi Bukit Meriam (Site 26, Candi Bukit Penjara (Site 25 and Candi Bukit Gajah Mati (Site 7. On the whole, this temple was made from bricks and based on the north-south orientation and the construction of the lotus-like structure, it is believed that this temple is of Buddhist religion and was built between 9th to 10th century AD. Based on GPS reading, the temple’s location is N5 37.129 E100 27.324. Analysis on the bricks of the temple was performed to determine whether the bricks used local raw material or otherwise, as well as to find out the physical condition of the bricks, particularly their burning method. As such, two analysis techniques were conducted, namely the X-Ray Diffraction and the X-Ray Fluorescence method that respectively determined the mineral content of the bricks as well as the major and trace element content of the bricks. Analysis shows that the minerals contained in the brick samples of Candi Bukit Kechil comprise of quartz, muscovite, albite and kaolinite. The presence of the kaolinite mineral shows that there are bricks that were baked at temperatures less than 550°C and this shows that open burning was used. The analyses of major and trace element content show that the raw material used are local raw material and the sources of the raw material were obtained from the area of the Bujang River basin and the areas around Mukim Merbok and Mukim Bujang.

  15. Internal insulation applied in heritage multi-storey buildings with wooden beams embedded in solid masonry brick facades

    DEFF Research Database (Denmark)

    Harrestrup, Maria; Svendsen, Svend

    2016-01-01

    The use of internal insulation is investigated in a heritage building block with wooden beam construction and masonry brick walls as part of an energy renovation. Measurements were carried out and compared to results from a hygrothermal simulation model. The risk of mould growth in the wooden beams...... and in the interface between the insulation and the brick wall was evaluated. Three different insulation strategies for applying internal insulation were investigated: 1) insulation applied on the entire interior facade; 2) 200 mm gap in the insulation above the floor; and 3) 200 mm gap in the insulation both above...

  16. Brick Paving Systems in Expeditionary Environments: Field Testing

    Science.gov (United States)

    2012-07-01

    Dynamic Cone Penetrometer (DCP) tests were conducted on each test item as an alternative strength measurement to the in situ CBR tests conducted on the...many passes of the C-17 load before failure. Between 20 and 40 passes, the majority of the bricks in the wheel path began to break or shatter . Figures...American Society for Testing and Materials. 2003. Standard test method for use of the dynamic cone penetrometer in shallow pavement applications

  17. Using rice straw to manufacture ceramic bricks

    National Research Council Canada - National Science Library

    Gorbunov, G. I; Rasulov, O. R

    2014-01-01

    In the article, the co-authors offer their advanced and efficient methodologies for the recycling of the rice straw, as well as the novel approaches to the ceramic brick quality improvement through...

  18. Fingermark recovery from riot debris: Bricks and stones.

    Science.gov (United States)

    Davis, Lisa; Fisher, Ruth

    2015-03-01

    During the UK riots in August 2011, large volumes of bricks and stones were used as weapons or projectiles in acts of violence or to gain illegal entry to properties. As a result, it has been emphasised that it is necessary to determine suitable chemical treatment(s) that will enable the development of fingermarks on such items in order to identify those involved. This study has undertaken the task of attempting to develop latent fingermarks on common house bricks, limestone and sandstone using current techniques including ninhydrin and fluorescence. Results produced have shown that, with fluorescent fingerprint powder, silver nitrate and superglue providing the best results, it is now possible to enhance fingermarks that were previously left undeveloped. In addition, Isomark T-1 Rapid Grey High Resolution Forensic Impression Material has proved extremely effective as an alternative method of recovering fingermarks developed with fluorescent fingerprint powder.

  19. Respiratory Abnormalities among Occupationally Exposed, Non-Smoking Brick Kiln Workers from Punjab, India

    Directory of Open Access Journals (Sweden)

    Supriya Tandon

    2017-07-01

    Full Text Available Background: Brick manufacturing industry is one of the oldest and fast-growing industries in India that employs a large section of people. Brick kiln workers are occupationally exposed to air pollutants. Nonetheless, only a few studies have so far been conducted on their respiratory health. Objective: To investigate the extent of respiratory impairment in brick kiln workers and to correlate it with the duration of exposure. Methods: A cross-sectional study was conducted. Spirometric parameters of 110 non-smoking male brick kiln workers aged 18–35 years in Patiala district, Punjab, India, were compared with an age-matched comparison group of 90 unexposed individuals. Results: Brick kiln workers showed a significant (p8 years of exposure, the mean values of FEV1 (1.92 L, FVC (2.01 L, FEF25-75% (2.19 L/s and PEFR (4.81 L/s were significantly (p<0.05 lower than those recorded in workers with <8 years of exposure in whom the values were 2.01 L, 2.68 L, 2.71 L/s, and 5.76 L/s, respectively. Conclusion: There is a significant association between exposure to workplace pollutants and lung function deterioration among brick kiln workers.

  20. A linear sampling method for through-the-wall radar detection

    Science.gov (United States)

    Charnley, Matthew; Wood, Aihua

    2017-10-01

    The through-the-wall inverse scattering problem is analyzed via the linear sampling method. The reciprocity gap formulation of the linear sampling method is used to reconstruct an object within a closed-off room. In order to apply this method, a numerical method to model a point source is needed, along with knowledge of how the numerical fundamental solution differs from the analytic one. Application of the linear sampling method to the Finite Difference Time Domain solution is described and illustrated, and results to reconstruct objects in the through-the-wall setting are shown.

  1. Thermal Performance of Hollow Clay Brick with Low Emissivity Treatment in Surface Enclosures

    Directory of Open Access Journals (Sweden)

    Roberto Fioretti

    2014-10-01

    Full Text Available External walls made with hollow clay brick or block are widely used for their thermal, acoustic and structural properties. However, the performance of the bricks frequently does not conform with the minimum legal requirements or the values required for high efficiency buildings, and for this reason, they need to be integrated with layers of thermal insulation. In this paper, the thermal behavior of hollow clay block with low emissivity treatment on the internal cavity surfaces has been investigated. The purpose of this application is to obtain a reduction in the thermal conductivity of the block by lowering the radiative heat exchange in the enclosures. The aims of this paper are to indicate a methodology for evaluating the thermal performance of the brick and to provide information about the benefits that should be obtained. Theoretical evaluations are carried out on several bricks (12 geometries simulated with two different thermal conductivities of the clay, using a finite elements model. The heat exchange procedure is implemented in accordance with the standard, so as to obtain standardized values of the thermal characteristics of the block. Several values of emissivity are hypothesized, related to different kinds of coating. Finally, the values of the thermal transmittance of walls built with the evaluated blocks have been calculated and compared. The results show how coating the internal surface of the cavity provides a reduction in the thermal conductivity of the block, of between 26% and 45%, for a surface emissivity of 0.1.

  2. Improved methods for binding acma-type protein anchor fusions yo cell-wall material of micro-organisms

    NARCIS (Netherlands)

    Leenhouts, Cornelis; Ramasamy, R.; Steen, Anton; Kok, Jan; Buist, Girbe; Kuipers, Oscar

    2002-01-01

    The invention provides a method for improving binding of a proteinaceous substance to cell-wall material of a Gram-positive bacterium, said substance comprising an AcmA cell wall binding domain or homolog or functional derivative thereof, said method comprising treating said cell-wall material with

  3. A hybrid method for airway segmentation and automated measurement of bronchial wall thickness on CT.

    Science.gov (United States)

    Xu, Ziyue; Bagci, Ulas; Foster, Brent; Mansoor, Awais; Udupa, Jayaram K; Mollura, Daniel J

    2015-08-01

    Inflammatory and infectious lung diseases commonly involve bronchial airway structures and morphology, and these abnormalities are often analyzed non-invasively through high resolution computed tomography (CT) scans. Assessing airway wall surfaces and the lumen are of great importance for diagnosing pulmonary diseases. However, obtaining high accuracy from a complete 3-D airway tree structure can be quite challenging. The airway tree structure has spiculated shapes with multiple branches and bifurcation points as opposed to solid single organ or tumor segmentation tasks in other applications, hence, it is complex for manual segmentation as compared with other tasks. For computerized methods, a fundamental challenge in airway tree segmentation is the highly variable intensity levels in the lumen area, which often causes a segmentation method to leak into adjacent lung parenchyma through blurred airway walls or soft boundaries. Moreover, outer wall definition can be difficult due to similar intensities of the airway walls and nearby structures such as vessels. In this paper, we propose a computational framework to accurately quantify airways through (i) a novel hybrid approach for precise segmentation of the lumen, and (ii) two novel methods (a spatially constrained Markov random walk method (pseudo 3-D) and a relative fuzzy connectedness method (3-D)) to estimate the airway wall thickness. We evaluate the performance of our proposed methods in comparison with mostly used algorithms using human chest CT images. Our results demonstrate that, on publicly available data sets and using standard evaluation criteria, the proposed airway segmentation method is accurate and efficient as compared with the state-of-the-art methods, and the airway wall estimation algorithms identified the inner and outer airway surfaces more accurately than the most widely applied methods, namely full width at half maximum and phase congruency.

  4. [Research on the inner wall condition monitoring method of ring forgings based on infrared spectra].

    Science.gov (United States)

    Fu, Xian-bin; Liu, Bin; Wei, Bin; Zhang, Yu-cun; Liu, Zhao-lun

    2015-01-01

    In order to grasp the inner wall condition of ring forgings, an inner wall condition monitoring method based on infrared spectra for ring forgings is proposed in the present paper. Firstly, using infrared spectroscopy the forgings temperature measurement system was built based on the three-level FP-cavity LCTF. The two single radiation spectra from the forgings' surface were got using the three-level FP-cavity LCTF. And the temperature measuring of the surface forgings was achieved according to the infrared double-color temperature measuring principle. The measuring accuracy can be greatly improved by this temperature measurement method. Secondly, on the basis of the Laplace heat conduction differential equation the inner wall condition monitoring model was established by the method of separating variables. The inner wall condition monitoring of ring forgings was realized via combining the temperature data and the forgings own parameter information. Finally, this method is feasible according to the simulation experiment. The inner wall condition monitoring method can provide the theoretical basis for the normal operating of the ring forgings.

  5. Inverse method for the instantaneous measure of wall shear rate magnitude and direction using electrodiffusion probes

    Science.gov (United States)

    Lamarche-Gagnon, Marc-Etienne; Vetel, Jerome

    2016-11-01

    Several methods can be used when one needs to measure wall shear stress in a fluid flow. Yet, it is known that a precise shear measurement is seldom met, mostly when both time and space resolutions are required. The electrodiffusion method lies on the mass transfer between a redox couple contained in an electrolyte and an electrode flush mounted to a wall. Similarly to the heat transfer measured by a hot wire anemometer, the mass transfer can be related to the fluid's wall shear rate. When coupled with a numerical post-treatment by the so-called inverse method, precise instantaneous wall shear rate measurements can be obtained. With further improvements, it has the potential to be effective in highly fluctuating three-dimensional flows. We present developments of the inverse method to two-component shear rate measurements, that is shear magnitude and direction. This is achieved with the use of a three-segment electrodiffusion probe. Validation tests of the inverse method are performed in an oscillating plane Poiseuille flow at moderate pulse frequencies, which also includes reverse flow phases, and in the vicinity of a separation point where the wall shear stress experiences local inversion in a controlled separated flow.

  6. Results obtained during wall breaching research

    CSIR Research Space (South Africa)

    Hattingh, S

    2008-11-01

    Full Text Available the operator on the charge side of the building. Test walls (double and single brick walls) 3m wide by 2m height were used for testing different charges and their effects due to the different charges. The loop charge was found to be the most promising solution...

  7. Application of the electrodiffusion method for near-wall flow diagnostics

    Directory of Open Access Journals (Sweden)

    Tihon J.

    2014-03-01

    Full Text Available The electrodiffusion method is presented as a measuring technique suitable for the flow measurement done in close proximity of the wall, thus in the region difficultly accessible by standard anemometric techniques (e.g. PIV, LDA. The experimental results obtained in different flow configurations (backward-facing step flow, wavy film flow, turbulent channel flow, rising Taylor bubbles document application capabilities of this technique, e.g. for mapping of wall shear stresses, delimitation of stable flow-recirculation zones, detection of short-time reversal of the near-wall flow, investigation of the near-wall turbulence, or detection of moving fluid particles. A new technology of sensor fabrication based on photolithography is introduced and possible applications of microsensors in microfluidic devices discussed.

  8. Appeal to the politicians: 'Don't line brick buildings with cotton wool'. Appell an Politiker: 'Ziegelhaeuser nicht in Watte packen'

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1992-03-01

    The German Association of the Brick Industry is putting up a fight against 'exaggerated demands for a reduction of the K-value of thermal insulation for buildings'. In doing so it is cutting in on the debate about the amendment to the Ordinance on Thermal Insulation. The association will not accept 'plans to out construction methods such as single-shell walling from the market, methods that have proved their worth over the centuries and are ecologically safe'. (orig.).

  9. Ultrasonic Digital Communication System for a Steel Wall Multipath Channel: Methods and Results

    Energy Technology Data Exchange (ETDEWEB)

    Murphy, Timothy L. [Rensselaer Polytechnic Inst., Troy, NY (United States)

    2005-12-01

    As of the development of this thesis, no commercially available products have been identified for the digital communication of instrumented data across a thick ({approx} 6 n.) steel wall using ultrasound. The specific goal of the current research is to investigate the application of methods for digital communication of instrumented data (i.e., temperature, voltage, etc.) across the wall of a steel pressure vessel. The acoustic transmission of data using ultrasonic transducers prevents the need to breach the wall of such a pressure vessel which could ultimately affect its safety or lifespan, or void the homogeneity of an experiment under test. Actual digital communication paradigms are introduced and implemented for the successful dissemination of data across such a wall utilizing solely an acoustic ultrasonic link. The first, dubbed the ''single-hop'' configuration, can communicate bursts of digital data one-way across the wall using the Differential Binary Phase-Shift Keying (DBPSK) modulation technique as fast as 500 bps. The second, dubbed the ''double-hop'' configuration, transmits a carrier into the vessel, modulates it, and retransmits it externally. Using a pulsed carrier with Pulse Amplitude Modulation (PAM), this technique can communicate digital data as fast as 500 bps. Using a CW carrier, Least Mean-Squared (LMS) adaptive interference suppression, and DBPSK, this method can communicate data as fast as 5 kbps. A third technique, dubbed the ''reflected-power'' configuration, communicates digital data by modulating a pulsed carrier by varying the acoustic impedance at the internal transducer-wall interface. The paradigms of the latter two configurations are believed to be unique. All modulation methods are based on the premise that the wall cannot be breached in any way and can therefore be viably implemented with power delivered wirelessly through the acoustic channel using ultrasound. Methods

  10. Direct-bonded Magnesite-Chrome Bricks for Kilns and Furnaces of Building Materials Industry JC 497-92 ( 96 )

    Institute of Scientific and Technical Information of China (English)

    Yu Lingyan; Chai Junlan

    2008-01-01

    @@ 1 Contents and Applied Scope This standard specifies the classification, shapes and dimensions, technical requirements, test methods, inspection rules, marking, packing, transportation, storage and quality certificate of direct-bonded magne-site -chrome bricks for building materials industry.

  11. Building the Wall Brick by Brick: One Prospective Teacher's Experiences with Mathematics Anxiety

    Science.gov (United States)

    Stoehr, Kathleen Jablon

    2017-01-01

    Mathematics education researchers have investigated mathematics anxiety in prospective elementary teachers. While many of these studies have focused on the bodily sensations and emotions of mathematics anxiety, particularly those felt in assessment situations, opportunities remain to investigate how prospective elementary teachers interpret their…

  12. A method of computing the transient temperature of thick walls from arbitrary variation of adiabatic-wall temperature and heat-transfer coefficient

    Science.gov (United States)

    Hill, P R

    1958-01-01

    A method of calculating the temperature of thick walls has been developed in which the time series and the response to a unit triangle variation of surface temperature concepts are used, together with essentially standard formulas for transient temperature and heat flow into thick walls. The method can be used without knowledge of the mathematical tools of its development. The method is particularly suitable for determining the wall temperature in one-dimensional thermal problems in aeronautics where there is a continuous variation of the heat-transfer coefficient and adiabatic-wall temperature. The method also offers a convenient means for solving the inverse problem of determining the heat-flow history when temperature history is known.

  13. Properties of Nanocrystals-formulated Aluminosilicate Bricks

    Directory of Open Access Journals (Sweden)

    Francesca Conciauro

    2015-10-01

    insulating and/or mechanical properties. The nanocrystals- modified refractories showed variations in properties, with respect to the untreated aluminosilicate reference in heat- insulating performances (thermal diffusivities were measured by the “hot disk” technique. In general, they also showed improvements in mechanical compression resist‐ ance for all of the samples at 2 wt. %. The best heat insula‐ tion was obtained with the addition of nano-aluminium hydroxide at 2 wt. %, while the highest mechanical compres‐ sion breaking resistance was found with nano-CaCO3 at 2 wt. %. These outcomes were investigated with complemen‐ tary techniques, like mercury porosimetry for porosity, and Archimedes methods to measure physical properties like the bulk and apparent densities, apparent porosities and water absorption. The results show that the nano-alumini‐ um hydroxide modified bricks were the most porous, which could explain the best heat-insulating performances. There is a less straightforward explanation for the mechanical resistance results, as they may have relations with the characteristics of the pores. Furthermore, the nanoparti‐ cles may have possible reactions with the matrix during the heat treatments.

  14. Computation of turbulent boundary layers employing the defect wall-function method. M.S. Thesis

    Science.gov (United States)

    Brown, Douglas L.

    1994-01-01

    In order to decrease overall computational time requirements of spatially-marching parabolized Navier-Stokes finite-difference computer code when applied to turbulent fluid flow, a wall-function methodology, originally proposed by R. Barnwell, was implemented. This numerical effort increases computational speed and calculates reasonably accurate wall shear stress spatial distributions and boundary-layer profiles. Since the wall shear stress is analytically determined from the wall-function model, the computational grid near the wall is not required to spatially resolve the laminar-viscous sublayer. Consequently, a substantially increased computational integration step size is achieved resulting in a considerable decrease in net computational time. This wall-function technique is demonstrated for adiabatic flat plate test cases from Mach 2 to Mach 8. These test cases are analytically verified employing: (1) Eckert reference method solutions, (2) experimental turbulent boundary-layer data of Mabey, and (3) finite-difference computational code solutions with fully resolved laminar-viscous sublayers. Additionally, results have been obtained for two pressure-gradient cases: (1) an adiabatic expansion corner and (2) an adiabatic compression corner.

  15. A new method for measuring the oxygen diffusion constant and oxygen consumption rate of arteriolar walls.

    Science.gov (United States)

    Sasaki, Nobuhiko; Horinouchi, Hirohisa; Ushiyama, Akira; Minamitani, Haruyuki

    2012-01-01

    Oxygen transport is believed to primarily occur via capillaries and depends on the oxygen tension gradient between the vessels and tissues. As blood flows along branching arterioles, the O(2) saturation drops, indicating either consumption or diffusion. The blood flow rate, the O(2) concentration gradient, and Krogh's O(2) diffusion constant (K) of the vessel wall are parameters affecting O(2)delivery. We devised a method for evaluating K of arteriolar wall in vivo using phosphorescence quenching microscopy to measure the partial pressure of oxygen in two areas almost simultaneously. The K value of arteriolar wall (inner diameter, 63.5 ± 11.9 μm; wall thickness, 18.0 ± 1.2 μm) was found to be 6.0 ± 1.2 × 10(-11) (cm(2)/s)(ml O(2)·cm(-3) tissue·mmHg(-1)). The arteriolar wall O(2) consumption rate (M) was 1.5 ± 0.1 (ml O(2)·100 cm(-3) tissue·min(-1)), as calculated using Krogh's diffusion equation. These results suggest that the arteriolar wall consumes a considerable proportion of the O(2) that diffuses through it.

  16. Using Bonding Enamel-Coated Steel Fixtures to Produce More Durable Brick/Masonry Structures

    Science.gov (United States)

    2010-02-01

    very moist for long periods of times Corroded strap-type wall tie BUILDING STRONG® Ties Join Courses and Lateral Units  Ties hold brick veneer to a...onto the steel fittings  A layer of portland cement is added to the heat softened glass enamel  Finished reinforcement is corrosion resistant and...very corrosion resistant Cement fused to the glass enamel makes strong bond to surrounding mortar Steel is protected from corrosion as long as glass

  17. A simple, effective and clinically applicable method to compute abdominal aortic aneurysm wall stress.

    Science.gov (United States)

    Joldes, Grand Roman; Miller, Karol; Wittek, Adam; Doyle, Barry

    2016-05-01

    Abdominal aortic aneurysm (AAA) is a permanent and irreversible dilation of the lower region of the aorta. It is a symptomless condition that if left untreated can expand to the point of rupture. Mechanically-speaking, rupture of an artery occurs when the local wall stress exceeds the local wall strength. It is therefore desirable to be able to non-invasively estimate the AAA wall stress for a given patient, quickly and reliably. In this paper we present an entirely new approach to computing the wall tension (i.e. the stress resultant equal to the integral of the stresses tangent to the wall over the wall thickness) within an AAA that relies on trivial linear elastic finite element computations, which can be performed instantaneously in the clinical environment on the simplest computing hardware. As an input to our calculations we only use information readily available in the clinic: the shape of the aneurysm in-vivo, as seen on a computed tomography (CT) scan, and blood pressure. We demonstrate that tension fields computed with the proposed approach agree well with those obtained using very sophisticated, state-of-the-art non-linear inverse procedures. Using magnetic resonance (MR) images of the same patient, we can approximately measure the local wall thickness and calculate the local wall stress. What is truly exciting about this simple approach is that one does not need any information on material parameters; this supports the development and use of patient-specific modelling (PSM), where uncertainty in material data is recognised as a key limitation. The methods demonstrated in this paper are applicable to other areas of biomechanics where the loads and loaded geometry of the system are known. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Viscous Inner and Outer Pressure Forming Method of Thin-walled Tube and Its Application

    Institute of Scientific and Technical Information of China (English)

    GAO Tiejun; LIU Yang; WANG Zhongjin

    2015-01-01

    Aiming at overcoming the difficulties in integral forming of thin-walled tubes with complex shapes, a novel forming method by inner and outer pressure through viscous was proposed. In this method, by dividing large deformation of the part into inner and outer pressure forming deformations, the limit deformation of tube part can be increased by several times. Meanwhile, the principle of viscous inner and outer pressure forming was provided, and key problems during the forming process such as reduction of the wall-thickness and instability wrinkling were analyzed. Thereby, the complex curved surface super-alloy GH3044 thin-walled tube with varying diameter ratio of 1.35 (the ratio between the maximum and minimum diameters of the part) can be integrally formed by this method. The experimental surface of the formed part is superior in quality and the wall-thickness distribution is uniform. The results show that the viscous inner and outer pressure forming can provide a new approach for integral forming of thin-walled tubes with complex shapes.

  19. Investigation on vibration of single-walled carbon nanotubes by variational iteration method

    Science.gov (United States)

    Ahmadi Asoor, A. A.; Valipour, P.; Ghasemi, S. E.

    2016-02-01

    In this paper, the variational iteration method (VIM) has been used to investigate the non-linear vibration of single-walled carbon nanotubes (SWCNTs) based on the nonlocal Timoshenko beam theory. The accuracy of results is examined by the fourth-order Runge-Kutta numerical method. Comparison between VIM solutions with numerical results leads to highly accurate solutions. Also, the behavior of deflection and frequency in vibrations of SWCNTs are studied. The results show that frequency of single walled carbon nanotube versus amplitude increases by increasing the values of B.

  20. “Technical Properties of Pond Ash - Clay Fired Bricks – An Experimental Study”

    Directory of Open Access Journals (Sweden)

    Prashant G. Sonawane

    2013-09-01

    Full Text Available In the thermal power plants the coal is burnt to heat the water for making the steam, which in turn is used to run the turbines. The pond ash is a waste product from the boilers. It is mainly obtained from the wet disposal of the fly ash, which when get mixed with bottom ash is disposed off in large pond or dykes as slurry. The pond ash is being generated in an alarming rate. The generation of the pond ash is posing a lot of threat to environment and thus its sustainable management has become the thrust area in engineering research. As the pond ash is relatively coarse and the dissolvable alkalies present in it are washed with water, its pozzolanic reactivity becomes low and hence it is not preferred as part replacement of cement in concrete as in the case of fly ash. In this research work an attempt is made to find out the possibility of using pond ash in burnt clay bricks. The part of the clay is replaced by pond ash in different composition and the bricks are made in conventional method at a brick manufacturing plant. The bricks are fired in a traditional way as per usual practice in the area and the final products with different composition of pond ash are tested in laboratory; for tolerance in dimension, water absorption, compressive strength, initial rate of absorption and weathering. The results of all the tests on brick samples with different % of pond ash are compared with clay bricks and the effect on different characteristics of bricks due to addition of pond ash are studied.

  1. ZettaBricks: A Language Compiler and Runtime System for Anyscale Computing

    Energy Technology Data Exchange (ETDEWEB)

    Amarasinghe, Saman [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2015-03-27

    This grant supported the ZettaBricks and OpenTuner projects. ZettaBricks is a new implicitly parallel language and compiler where defining multiple implementations of multiple algorithms to solve a problem is the natural way of programming. ZettaBricks makes algorithmic choice a first class construct of the language. Choices are provided in a way that also allows our compiler to tune at a finer granularity. The ZettaBricks compiler autotunes programs by making both fine-grained as well as algorithmic choices. Choices also include different automatic parallelization techniques, data distributions, algorithmic parameters, transformations, and blocking. Additionally, ZettaBricks introduces novel techniques to autotune algorithms for different convergence criteria. When choosing between various direct and iterative methods, the ZettaBricks compiler is able to tune a program in such a way that delivers near-optimal efficiency for any desired level of accuracy. The compiler has the flexibility of utilizing different convergence criteria for the various components within a single algorithm, providing the user with accuracy choice alongside algorithmic choice. OpenTuner is a generalization of the experience gained in building an autotuner for ZettaBricks. OpenTuner is a new open source framework for building domain-specific multi-objective program autotuners. OpenTuner supports fully-customizable configuration representations, an extensible technique representation to allow for domain-specific techniques, and an easy to use interface for communicating with the program to be autotuned. A key capability inside OpenTuner is the use of ensembles of disparate search techniques simultaneously; techniques that perform well will dynamically be allocated a larger proportion of tests.

  2. Breath Figures of Nanoscale Bricks: A Universal Method for Creating Hierarchic Porous Materials from Inorganic Nanoparticles Stabilized with Mussel-Inspired Copolymers.

    Science.gov (United States)

    Saito, Yuta; Shimomura, Masatsugu; Yabu, Hiroshi

    2014-09-01

    High-performance catalysts and photovoltaics are required for building an environmentally sustainable society. Because catalytic and photovoltaic reactions occur at the interfaces between reactants and surfaces, the chemical, physical, and structural properties of interfaces have been the focus of much research. To improve the performance of these materials further, inorganic porous materials with hierarchic porous architectures have been fabricated. The breath figure technique allows preparing porous films by using water droplets as templates. In this study, a valuable preparation method for hierarchic porous inorganic materials is shown. Hierarchic porous materials are prepared from surface-coated inorganic nanoparticles with amphiphilic copolymers having catechol moieties followed by sintering. Micron-scale pores are prepared by using water droplets as templates, and nanoscale pores are formed between the nanoparticles. The fabrication method allows the preparation of hierarchic porous films from inorganic nanoparticles of various shapes and materials.

  3. 78 FR 44433 - Safety Zone; Metedeconk River; Brick Township, NJ

    Science.gov (United States)

    2013-07-24

    ... SECURITY Coast Guard 33 CFR Part 165 RIN 1625-AA00 Safety Zone; Metedeconk River; Brick Township, NJ AGENCY... regulation applies to only one recurring fireworks event held in the Metedeconk River in Brick Township, NJ... CFR 165.506, an entry 19 for the Metedeconk River, Brick Township, NJ Safety Zone will be added from...

  4. Effects of light curing method and resin composite composition on composite adaptation to the cavity wall.

    Science.gov (United States)

    Yoshikawa, Takako; Morigami, Makoto; Sadr, Alireza; Tagami, Junji

    2014-01-01

    This study aimed to evaluate the effects of the light curing method and resin composite composition on marginal sealing and resin composite adaptation to the cavity wall. Cylindrical cavities were prepared on the buccal or lingual cervical regions. The teeth were restored using Clearfil Liner Bond 2V adhesive system and filled with Clearfil Photo Bright or Palfique Estelite resin composite. The resins were cured using the conventional or slow-start light curing method. After thermal cycling, the specimens were subjected to a dye penetration test. The slow-start curing method showed better resin composite adaptation to the cavity wall for both composites. Furthermore, the slow-start curing method resulted in significantly improved dentin marginal sealing compared with the conventional method for Clearfil Photo Bright. The light-cured resin composite, which exhibited increased contrast ratios duringpolymerization, seems to suggest high compensation for polymerization contraction stress when using the slow-start curing method.

  5. Residual Mechanical Properties of Concrete Made with Crushed Clay Bricks and Roof Tiles Aggregate after Exposure to High Temperatures

    Directory of Open Access Journals (Sweden)

    Ivana Miličević

    2016-04-01

    Full Text Available This paper presents the residual mechanical properties of concrete made with crushed bricks and clay roof tile aggregates after exposure to high temperatures. One referent mixture and eight mixtures with different percentages of replacement of natural aggregate by crushed bricks and roof tiles are experimentally tested. The properties of the concrete were measured before and after exposure to 200, 400, 600 and 800 °C. In order to evaluate the basic residual mechanical properties of concrete with crushed bricks and roof tiles after exposure to high temperatures, ultrasonic pulse velocity is used as a non-destructive test method and the results are compared with those of a destructive method for validation. The mixture with the highest percentage of replacement of natural aggregate by crushed brick and roof tile aggregate has the best physical, mechanical, and thermal properties for application of such concrete in precast concrete elements exposed to high temperatures.

  6. Polydopamine microcapsules with different wall structures prepared by a template-mediated method for enzyme immobilization.

    Science.gov (United States)

    Shi, Jiafu; Yang, Chen; Zhang, Shaohua; Wang, Xiaoli; Jiang, Zhongyi; Zhang, Wenyan; Song, Xiaokai; Ai, Qinghong; Tian, Chunyong

    2013-10-23

    Microcapsules with diverse wall structures may exhibit different performance in specific applications. In the present study, three kinds of mussel-inspired polydopamine (PDA) microcapsules with different wall structures have been prepared by a template-mediated method. More specifically, three types of CaCO3 microspheres (poly(allylamine hydrochloride), (PAH)-doped CaCO3; pure-CaCO3; and poly(styrene sulfonate sodium), (PSS)-doped CaCO3) were synthesized as sacrificial templates, which were then treated by dopamine to obtain the corresponding PDA-CaCO3 microspheres. Through treating these microspheres with disodium ethylene diamine tetraacetic acid (EDTA-2Na) to remove CaCO3, three types of PDA microcapsules were acquired: that was (1) PAH-PDA microcapsule with a thick (∼600 nm) and highly porous capsule wall composed of interconnected networks, (2) pure-PDA microcapsule with a thick (∼600 nm) and less porous capsule wall, (3) PSS-PDA microcapsule with a thin (∼70 nm) and dense capsule wall. Several characterizations confirmed that a higher degree in porosity and interconnectivity of the capsule wall would lead to a higher mass transfer coefficient. When serving as the carrier for catalase (CAT) immobilization, these enzyme-encapsulated PDA microcapsules showed distinct structure-related activity and stability. In particular, PAH-PDA microcapsules with a wall of highly interconnected networks displayed several significant advantages, including increases in enzyme encapsulation efficiency and enzyme activity/stability and a decrease in enzyme leaching in comparison with other two types of PDA microcapsules. Besides, this hierarchically structured PAH-PDA microcapsule may find other promising applications in biocatalysis, biosensors, drug delivery, etc.

  7. Experimental evaluation of the strut-and-tie method applied to low-rise concrete walls

    Directory of Open Access Journals (Sweden)

    Julian Carrillo León

    2010-05-01

    0.25% and the type of web reinforcement against shear (corrugated bars and welded wire mesh. Wall properties were typical of low-rise housing in Mexico. When the calculated shear strength was compared with the measured one it was found that the S-T method proposed by the ACI-318 building code suitably estimated the shear capacity of the models being studied. However, the wall’s shear failure mode, loading rate, the number of cycles and the cumulative energy dissipated would noticeably affect the degradation in strength of low-rise, reinforced concrete walls.

  8. Probability-based method using RFEM for predicting wall deflection caused by excavation

    Institute of Scientific and Technical Information of China (English)

    Yu-geng TANG

    2011-01-01

    This study employs the random finite element method (RFEM) to analyze the wall deflection caused by excavation.The RFEM combined random fields of material properties with the FEM through the Monte Carlo simulation.A well-documented excavation case history is employed to evaluate the influence of uncertainty of analysis parameters.This study shows that RFEM can provide reasonable estimations of the exceedance probability of wall deflection caused by excavation,and has the potential to be a useful tool to account for the uncertainties of material and model parameters in the numerical analysis.

  9. Method of fabricating thin-walled articles of tungsten-nickel-iron alloy

    Science.gov (United States)

    Hovis, V.M. Jr.; Northcutt, W.G. Jr.

    The present invention relates to a method for fabricating thin-walled high-density structures of tungsten-nickel-iron alloys. A powdered blend of the selected alloy constituents is plasma sprayed onto a mandrel having the desired article configuration. The sprayed deposit is removed from the mandrel and subjected to liquid phase sintering to provide the alloyed structure. The formation of the thin-walled structure by plasma spraying significantly reduces shrinkage, and cracking while increasing physical properties of the structure over that obtainable by employing previously known powder metallurgical procedures.

  10. The gamma-ray and neutron shielding factors of fly-ash brick materials.

    Science.gov (United States)

    Singh, Vishwanath P; Badiger, N M

    2014-03-01

    A comprehensive study of gamma-ray exposure build-up factors (EBFs) of fly-ash brick materials has been carried out for photon energies of 0.015-15 MeV up to a penetration depth of 40 mfp (mean free path) by a geometrical progression (GP) fitting method. The EBF values of the fly-ash brick materials were found to be dependent upon the photon energy, penetration depth and chemical composition, and were found to be higher than the values for mud bricks and common bricks. Above a photon energy of 3 MeV for large penetration depths (>10 mfp), the EBF becomes directly proportional to Zeq. EBFs of fly-ashes were found to be less than or equal to those of concrete for low penetration depths (shielding effectiveness. The shielding effectiveness of the fly-ash materials against gamma-ray radiation was lower than that of common and mud bricks.

  11. Physical and Mechanical Properties of Bodymill Sludge (BS) Incorporated Into Fired Clay Brick

    Science.gov (United States)

    Kadir, Aeslina Abdul; Rahim, Ahmad Shayuti Abdul; Ikhmal Haqeem Hassan, Mohd; Bakri Abdullah, Mohd Mustafa Al

    2016-06-01

    The huge volume of mosaic sludge that has been produced and the effect towards the environment had lead to the investigation of incorporating mosaic sludge into fired clay brick. In this study, the research attempt to reuse bodymill sludge (BS) from mosaic manufacturing process. The mosaic sludge is used to replace the raw material of clay up to 30%. In this investigation, the composition and concentration of heavy metal were determined by using X-Ray Fluorescence Spectrometer (XRF). Physical and mechanical properties test were also conducted such as compressive strength, shrinkage, density and initial rate of suction. Scanning Electron microscope was carried out to determine surface changes of the manufactured sludge brick. From the results, it shows that brick with 5% of BS sludge obtained the highest compressive strength and lower total shrinkage compared to other percentages. Nevertheless, all the other properties for all bricks incorporated with different percentages of mosaic sludge were complied with the standard (BS 3291:1985). Thus, mosaic sludge could be an alternative low cost material for brick and at the same time provide an environmental friendly disposal method for the waste.

  12. A method for the estimate of the wall diffusion for non-axisymmetric fields using rotating external fields

    Science.gov (United States)

    Frassinetti, L.; Olofsson, K. E. J.; Fridström, R.; Setiadi, A. C.; Brunsell, P. R.; Volpe, F. A.; Drake, J.

    2013-08-01

    A new method for the estimate of the wall diffusion time of non-axisymmetric fields is developed. The method based on rotating external fields and on the measurement of the wall frequency response is developed and tested in EXTRAP T2R. The method allows the experimental estimate of the wall diffusion time for each Fourier harmonic and the estimate of the wall diffusion toroidal asymmetries. The method intrinsically considers the effects of three-dimensional structures and of the shell gaps. Far from the gaps, experimental results are in good agreement with the diffusion time estimated with a simple cylindrical model that assumes a homogeneous wall. The method is also applied with non-standard configurations of the coil array, in order to mimic tokamak-relevant settings with a partial wall coverage and active coils of large toroidal extent. The comparison with the full coverage results shows good agreement if the effects of the relevant sidebands are considered.

  13. On the accuracy of analytical methods for turbulent flows near smooth walls

    Science.gov (United States)

    Absi, Rafik; Di Nucci, Carmine

    2012-09-01

    This Note presents two methods for mean streamwise velocity profiles of fully-developed turbulent pipe and channel flows near smooth walls. The first is the classical approach where the mean streamwise velocity is obtained by solving the momentum equation with an eddy viscosity formulation [R. Absi, A simple eddy viscosity formulation for turbulent boundary layers near smooth walls, C. R. Mecanique 337 (2009) 158-165]. The second approach presents a formulation of the velocity profile based on an analogy with an electric field distribution [C. Di Nucci, E. Fiorucci, Mean velocity profiles of fully-developed turbulent flows near smooth walls, C. R. Mecanique 339 (2011) 388-395] and a formulation for the turbulent shear stress. However, this formulation for the turbulent shear stress shows a weakness. A corrected formulation is presented. Comparisons with DNS data show that the classical approach with the eddy viscosity formulation provides more accurate profiles for both turbulent shear stress and velocity gradient.

  14. Model-based near-wall reconstructions for immersed-boundary methods

    Science.gov (United States)

    Posa, Antonio; Balaras, Elias

    2014-08-01

    In immersed-boundary methods, the cost of resolving the thin boundary layers on a solid boundary at high Reynolds numbers is prohibitive. In the present work, we propose a new model-based, near-wall reconstruction to account for the lack of resolution and provide the correct wall shear stress and hydrodynamic forces. The models are analytical versions of a generalized version of the two-layer model developed by Balaras et al. (AIAA J 34:1111-1119, 1996) for large-eddy simulations. We will present the results for the flow around a cylinder and a sphere, where we use Cartesian and cylindrical coordinate grids. We will demonstrate that the proposed treatment reproduces very accurately the wall stress on grids, which are one order of magnitude coarser compared to well-resolved simulations.

  15. Beyond the Brick Walls: Homeschooling Students with Special Needs

    Science.gov (United States)

    Cook, Kathleen B.; Bennett, Katie E.; Lane, Justin D.; Mataras, Theologia K.

    2013-01-01

    The percentage of children with special needs receiving academic instruction at home has substantially increased since a resurgence of homeschooling during the 1990s. In light of this information, the purpose of this article was to provide an overview of the history and laws related to homeschooling, the characteristics of homeschool families, and…

  16. Some recommendations for the construction of walls using adobe bricks

    OpenAIRE

    Miguel Ángel Rodríguez-Díaz; Belkis Saroza-Horta; Pedro Nolasco Ruiz-Sánchez; Ileana Julia Barroso-Valdés; Fernando Ariznavarreta-Fernández; Felipe González-Coto

    2014-01-01

    En el presente artículo se estudian las condiciones en las que deben ser levantados los muros de adobe en construcciones de tierra. Para ello, se construye una edificación piloto en Villa Clara, Cuba, que ha servido de base para probar distintas soluciones constructivas. Como resultado de esta investigación se dan recomendaciones para evitar el ascenso de la humedad por capilaridad, sobre la velocidad de levantamiento, la longitud de muro adecuada, el mortero de unión tanto de adobes entre sí...

  17. Some recommendations for the construction of walls using adobe bricks

    Directory of Open Access Journals (Sweden)

    Miguel Ángel Rodríguez-Díaz

    2014-01-01

    Full Text Available En el presente artículo se estudian las condiciones en las que deben ser levantados los muros de adobe en construcciones de tierra. Para ello, se construye una edificación piloto en Villa Clara, Cuba, que ha servido de base para probar distintas soluciones constructivas. Como resultado de esta investigación se dan recomendaciones para evitar el ascenso de la humedad por capilaridad, sobre la velocidad de levantamiento, la longitud de muro adecuada, el mortero de unión tanto de adobes entre sí como de adobe con otro material, el cerramento, los dinteles, la protección de vanos así como para el revestimiento adecuado para la protección del muro de adobe del intemperismo.

  18. The Brick Wall: Why So Few Women Become Senior Academics.

    Science.gov (United States)

    Bacchi, Carol

    1993-01-01

    It is proposed that, to address the lack of women in senior academic ranks, higher education should reexamine appointment procedures, scrutinize the standards by which men have been assessed traditionally, ask men to justify their own merit, and examine the way in which male academics interact with their female counterparts. (MSE)

  19. Investigation on Production and Markets of Silica Bricks in China

    Institute of Scientific and Technical Information of China (English)

    ZHANGZhongqi; CHUGuosheng; WANGTiezheng; PANShangxin

    2003-01-01

    The annual output of China's silica brick amounts up to over 300 thousand tons, which accounts for more than 70% of the total oupout of silica bricks in the world. Besides satisfying domestic markets, China's silica bricks have been exported to many countries and retions such as Japan, USA etc. In this paper, the situation of silica bricks production, technology, sales and exporting have been described. Also suggestions on improvement of silica bricks quality and exporting, corporation with foreign partners have been put forward in order to win larger market share both aat home and abroad.

  20. Investigation on Production and Markets of Silica Bricks in China

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zhongqi; CHU Guosheng; WANG Tiezheng; PAN Shangxin

    2003-01-01

    The annual output of China' s silica brick amounts up to over 300 thousand tons, which accounts for more than 70% of the total output of silica bricks in the world.Besides satisfying domestic markets, China's silica bricks have been exported to many countries and regions such as Japan, USA etc. In this paper, the situation of silica bricks production, technology, sales and exporting have been described. Also suggestions on improvement of silica bricks quality and exporting, corporation with foreign partners have been put forward in order to win larger market share both at home and abroad.

  1. Adherence Characteristics of Cement Clinker on Basic Bricks

    Institute of Scientific and Technical Information of China (English)

    GUO Zongqi; Michel Rigaud

    2002-01-01

    Based on the sandwich test, adherence mechanisms of cement clinker on various basic bricks were tackled by microstructural observations with help of cathodoluminescence technique. Doloma based bricks offer sufficient lime to react with clinker, forming C3 S rich layer and initializing superior adherence. However, clinker with low silica ratio leads to MgO agglomeration at the interface of doloma bricks, which reduces adherence strength. On magnesia spinel bricks, fine, crystalline spinel easily reacts with lime containing phases from clinker to form lowmelting phases and belite zone, which shows high adherence performance. Lack of fine spinel in magnesia spinel bricks results in poor adherence.

  2. Development of Andalusite Bricks for Hot Blast Stove

    Institute of Scientific and Technical Information of China (English)

    KANG Huarong; LI Xianming; DONG Shengying; XUE Wendong; LI Yong; SONG Wen

    2008-01-01

    Low-creep andalusite bricks are characterized by high refractoriness under load, good anti-creep property, high mechanical strength, low porosity, good thermal shock resistance, etc. In this study, low-creep andalusite brick specimens were investigated in the lab using mullite, bauxite and andalusite. Andalusite with the different panicle sizes were used in the experiment and the specimen with the best property was selected as the production standard. In addition, the industrial produced low-creep andalusite bricks were compared with other low-creep bricks. The results show that the developed low-creep andalusite bricks is an excellent material for hot blast stove.

  3. Experimental evaluation of the prevention methods for the interface between masonry infill walls and concrete columns

    Directory of Open Access Journals (Sweden)

    A. P. Tramontin

    Full Text Available Cracks that form at the interfaces between masonry structures are common uncontrolled occurrences in buildings. Numerous methods have been proposed by the construction industry to address this problem. Cracks continuously form in the joints between concrete columns and masonry infill walls. In this study, the most common methods for preventing these types of cracks were evaluated in laboratory experiments. Column masonry models were constructed using different types of joints between concrete columns and masonry infill walls, such as steel bars and steel mesh. The efficiency of each type of joint method was evaluated by performing direct tensile tests (pullout tests on the models and monitoring the evolution of the crack opening in the joint between the column and wall, as a function of load applied to the model. The results from this study indicate that the model composed of "electrowelded wire mesh without steel angles" is the best model for controlling cracking in the joints between concrete columns and masonry infill walls.

  4. Using rice straw to manufacture ceramic bricks

    Directory of Open Access Journals (Sweden)

    Gorbunov German Ivanovich

    2014-12-01

    Full Text Available In the article, the co-authors offer their advanced and efficient methodologies for the recycling of the rice straw, as well as the novel approaches to the ceramic brick quality improvement through the application of the rice straw as the combustible additive and through the formation of amorphous silica in the course of the rice straw combustion. The co-authors provide characteristics of the raw materials, production techniques used to manufacture ceramic bricks, and their basic properties in the article. The co-authors describe the simulated process of formation of amorphous silica. The process in question has two independent steps (or options: 1 rice straw combustion and ash formation outside the oven (in the oxidizing medium, and further application of ash as the additive in the process of burning clay mixtures; 2 adding pre-treated rice straw as the combustible additive into the clay mixture, and its further burning in compliance with the pre-set temperature mode. The findings have proven that the most rational pre-requisite of the rice straw application in the manufacturing of ceramic bricks consists in feeding milled straw into the clay mixture to be followed by molding, drying and burning. Brick samples are highly porous, and they also demonstrate sufficient compressive strength. The co-authors have also identified optimal values of rice straw and ash content in the mixtures under research.

  5. 混凝土砂基透水路面砖制备及物理性能测试%Precasting method and physical property test of sand-based concrete permeable pavement bricks

    Institute of Scientific and Technical Information of China (English)

    徐向舟; 朱晓斌; 刘璐; 王云闯; 王萍萍

    2014-01-01

    Promoting sand-based permeable brick is an effective way to recycle desert sand.A kind of sand-based permeable brick with precast permeable pores is developed.The brick is composed with roast sand as the aggregate and high-strength grading concrete as the binder,and is formed under static pressure.A series of physical performance tests and cost analyses are then conducted.The results are as follows:(1)Compressive strength of the permeable brick reaches up to 100 MPa,which is highly above the requirement of Cc60 permeable brick in the Construction Material Industry Standard in China.(2 )The pre-fabricated penetrating hole makes the permeability of the brick far ahead of the Construction Material Industry Standard in China.Moreover,it is not so easy to clog, and does not influence the comfort of the pavement,for the hole is so small in diameter on the top and large at the bottom.(3)Comprehensively considering the compressive strength,permeability,water retention,cost and so on,the following two schemes are chosen for future study:The 20th group is selected as the high-strength permeable brick,of which the fine sand ratio is 70%,the water cement ratio is 0.34,the porosity is 2% and the additive is the aqueous neoprene,in short AN;and the 22th group is more suitable to be used on the plaza pavement,of which the fine sand ratio is 85%,the water cement ratio is 0.30,the porosity is 1%,and no additive is added.(4)Increasing the coarse aggregate content could significantly augment the compressive strength of permeable brick. A preferable fine sand ratio is 70%-85%.(5)On the other hand,to mix an appropriate kind of additive with proper dosage is another way to enhance the brick.(6)Except higher cost of groups 7,11,12, 19,the cost of other groups is between 60-100 Yuan/m2 ,which is close to that of general no-sand permeable concrete brick,and far lower than that of the same kind of sand-based permeable brick.%推广砂基透水砖是实现沙漠沙资源化的有效途径.

  6. Recycling of sugarcane bagasse ash waste in the production of clay bricks.

    Science.gov (United States)

    Faria, K C P; Gurgel, R F; Holanda, J N F

    2012-06-30

    This work investigates the recycling of sugarcane bagasse ash waste as a method to provide raw material for clay brick bodies, through replacement of natural clay by up 20 wt.%. Initially, the waste sample was characterized by its chemical composition, X-ray diffraction, differential thermal analysis, particle size, morphology and pollution potential. Clay bricks pieces were prepared, and then tested, so as to determine their technological properties (e.g., linear shrinkage, water absorption, apparent density, and tensile strength). The sintered microstructure was evaluated by scanning electron microscopy (SEM). It was found that the sugarcane bagasse ash waste is mainly composed by crystalline silica particles. The test results indicate that the sugarcane bagasse ash waste could be used as a filler in clay bricks, thus enhancing the possibility of its reuse in a safe and sustainable way.

  7. Comparative Numerical Analysis of Different Strengthening Systems of Historical Brick Arches

    Science.gov (United States)

    Zielińska, M.

    2017-05-01

    The article presents a comparative numerical analysis of various ways to strengthen historical brick arches. Five ways of strengthening brick arches with steel tie-rods have been proposed. Two of these involve the use of braces wrapped around pillars supporting the arch connected with a tie-rod; the other two ways involve the use of the tie-rods with welded metal sheets of different sizes; the latter involves the use of a tie-rod glued with the use of an epoxy adhesive. The collected data were compared with the reference model of the arch left without any interference. The results make it possible to evaluate the effectiveness of the methods by comparing displacements in the vertical and horizontal direction and stresses. The article indicates the direction of proper planning and design of the arch strengthening in brick structures in historical buildings.

  8. Life cycle assessment of regional brick manufacture

    Directory of Open Access Journals (Sweden)

    López-Aguilar, H. A.

    2016-06-01

    Full Text Available This document presents a Life Cycle Assessment (LCA study to quantify the environmental cradle-to-gate impact of the manufacture of brick for the construction industry, produced with material of igneous source. Its mineral composition and thermal isolation properties were characterized for use in real estate construction. The LCA results for brick manufacture using this material identified the greatest environmental impact to be associated with material extraction and its proportional cement content. Additionally, this document presents an evaluation of the environmental impact of the manufacturing process by comparing traditional fired clay brick and brick of the material under study. In conclusion, the studied material shows thermal insulation qualities and suitability for the manufacture of bricks with low incorporated energy.Este trabajo presenta un estudio de Análisis de Ciclo de Vida (ACV para cuantificar los impactos ambientales de la cuna a la puerta de la manufactura de ladrillos para la industria de la construcción, fabricados de un material de origen ígneo. Se caracterizó su composición mineralógica y propiedades de aislamiento térmico para ser usado en la construcción de inmuebles. Los resultados ACV de la fabricación de ladrillos de este material, identificaron la mayor contribución a los impactos ambientales asociados a la extracción del material y la cantidad proporcional de cemento. Adicionalmente, se presenta una evaluación comparativa del impacto ambiental entre la manufactura de un ladrillo tradicional de arcilla cocido y de un ladrillo del material en estudio. En conclusión el material estudiado muestra cualidades de aislamiento térmico y es adecuado para la fabricación de ladrillos con baja energía incorporada.

  9. Experimental investigations on dry stone masonry walls

    OpenAIRE

    2006-01-01

    Brick unreinforced masonry walls have been widely studied both from experimental and numerical point of view, but scarce experimental information is available for dry stone masonry walls that constitute the material more frequently used in the construction of ancient historical constructions. Therefore, the present work aims at increasing the insight about the behavior of typical ancient masonry walls under cyclic loading. To attain such goal, different experimental approaches are consi...

  10. Control of Mechanical Stresses of High Pressure Container Walls by Magnetoelastic Method

    Science.gov (United States)

    Kulak, S. M.; Novikov, V. F.; Baranov, A. V.

    2016-10-01

    Deformations of the walls of pressure vessels arising in the process of testing and operation, as well as reduce their thickness due to corrosion, to create the prerequisites for the growth of mechanical stresses which accelerating the processes of strain aging, embrittlement of the material and reducing its fatigue properties. This article is devoted to researches of the magnetoelastic demagnetization in the wall of steel vessel of loading by internal pressure. It is established that the increasing pressure on the vessel wall is accompanied by a monotonic decrease in the intensity of the magnetic stray field of local magnetization of steel. It is shown that a magnetic stray field of local magnetization of the wall of steel vessel is non-uniform due to differences in structure and stresses. It is proposed to use the obtained results to control the stress state of vessels, experiencing multi-axial loads generated by internal pressure (pipelines, oil tanks, etc.) The method of magnetoelastic of the demagnetization of the steel has a high sensitivity to mechanical stress, the simplicity of implementation and expressiveness compared to the strain gauge and method of coercive force.

  11. Papercrete brick as an alternate building material to control Environmental Pollution

    Science.gov (United States)

    Sudarsan, J. S.; Ramesh, S.; Jothilingam, M.; Ramasamy, Vishalatchi; Rajan, Rajitha J.

    2017-07-01

    Utilization of concrete in the construction industry is increasing day by day. The increasing demand for concrete in the future is the major issue, for which an alternate option is to find out at a reduced or no additional cost and to reduce the environmental impact due to increase of cement industries that are important ingredient to economic development. It turns out urgent to find out alternate for the partial replacement of concrete and cement, as natural sources of aggregates are becoming exhausted. As large quantity of paper waste is generated from different countries all over the world which causes serious environmental problems, So in this present study abandoned paper waste was used as a partial replacement material in concrete,. Study indicates that 80% of the construction cost of a building was contributed by building material and still millions of people in developing countries like India are not able to afford the cost of construction of house. This study is based on potential use of light weight composite brick as a building material and potential use of paper waste for producing at low-cost. Experimental investigation was carried out to analyse optimization of mix for papercrete bricks depending upon the water absorption, compressive strength and unit weight. Papercrete bricks were prepared out of waste paper, and quarry dust with partial replacement of cement by another industrial by-product Fly Ash in varying proportions of 25%, 40% and 55%. The properties like mechanical strength, standard quality comparisons with the conventional bricks through standard tests like hardness, soundness, fire resistance and Cost-Benefit Analysis were performed and studied. The specimens of dimension 230mm x 110mm x 80mm were subjected to 7 Days and 28 days air curing and sun drying before tests were performed on them. Based on the study it was found that for non-load bearing walls papercrete bricks are best suited.

  12. Increasing the energy-efficiency in the production of bricks; Steigerung der Energieeffizienz in der Backsteinproduktion

    Energy Technology Data Exchange (ETDEWEB)

    Wurche, J.-P. [Kiefer und Partners AG, Zuerich (Switzerland); Gubler, Ch. [Ziegelei Fisibach AG, Bauma (Switzerland)

    2006-07-01

    This final report for the Swiss Federal Office of Energy (SFOE) presents the results of a research project that defined a universally valid concept for the analysis of potential for the reduction of the energy consumption of the installations in older brick-manufacturing facilities. The brick manufacturing process is described and the energy-households of the ovens and dryers are analysed. Methods used for the measurement of energy flows are described and the development of a simulation tool is discussed. Various possibilities for increasing energy-efficiency are looked at. The paper is rounded off with graphically-illustrated listings of the results obtained.

  13. Evaluation of the behavior of brick tile masonry and mortar due to capillary rise of moisture

    Directory of Open Access Journals (Sweden)

    Camino, M. S.

    2014-06-01

    Full Text Available For a better understanding of the behaviour of old brick masonry in facing the rising damp problem, multiple tests were made in the laboratory: water absorption, moisture content, apparent porosity, temperature and thermal camera imaging on brick masonry and its components: brick and mortar. This has allowed us to determine which of the previous tests is the best in predicting the behaviour of a real wall. In addition, the tests have also helped in defining a process to evaluate the moisture content of walls in a buildings, which is important for heritage restoration projects.Para un mejor conocimiento del comportamiento de las fábricas antiguas de ladrillo frente a la ascensión capilar de agua, se han realizado en laboratorio ensayos de absorción de agua, de contenido de humedad, de porosidad aparente, de temperatura e imágenes con cámara termográfica sobre muros de fábrica y sus materiales componentes: ladrillo y argamasa. Ello ha permitido inferir cuál es el ensayo realizado a los ladrillos que mejor predice el comportamiento del muro real. También ha permitido definir un procedimiento para evaluar el contenido de humedad de fábricas existentes, importante para los proyectos de restauración del patrimonio construido.

  14. Recycling industrial waste in brick manufacture. Part 1

    Directory of Open Access Journals (Sweden)

    Andreola, F.

    2005-12-01

    Full Text Available The ongoing accumulation of industrial waste speaks to the need to seek cost-effective disposal methods. Brick manufacture would appear to be particularly promising in this regard. The present study analyzes the possibility of recycling the sludge generated in porcelain tile polishing, as well as coal, steel and municipal incinerator ash to make a special type of facing brick whose properties readily accommodate a full analysis of all the problems deriving from the incorporation of residue in its manufacture. Physical-chemical, mechanical and structural analyses were performed on bricks made with varying percentages of the different types of waste considered. This first paper reports the results of the physical arid technological characterization of the products; the second part of the research will address their chemical, mechanical and structural properties.

    El continuo aumento de la cantidad de residuos (desechos que se generan en los procesos industriales induce a buscar nuevos métodos alternativos a la disposición final que sean altamente eficientes y a bajo costo. La industria manufac turera de ladrillos resulta muy prometedora desde este punto de vista. En este trabajo ha sido investigada la posibilidad de usar distintos residuos industriales, entre ellos barros de pulido del gres porcelánico. cenizas de carbón, cenizas de acerías y de incinerador municipal para la fabricación de ladrillos de exteriores. Fueron analizados los problemas que podrían derivar al introducir estos residuos en la pasta. En particular, en esta primera parte del trabajo se muestran los resultados derivados de la introducción de los residuos considerados, en distintos porcentajes, sobre las propiedades físicas y tecnológicas del producto final. En la segunda parte se desarrollarán los efectos causados sobre las propiedades químicas, mecánicas y microestructurales.

  15. An analytical method for calculating stresses and strains of ATF cladding based on thick walled theory

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong Hyun; Kim, Hak Sung [Hanyang University, Seoul (Korea, Republic of); Kim, Hyo Chan; Yang, Yong Sik; In, Wang kee [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    In this paper, an analytical method based on thick walled theory has been studied to calculate stress and strain of ATF cladding. In order to prescribe boundary conditions of the analytical method, two algorithms were employed which are called subroutine 'Cladf' and 'Couple' of FRACAS, respectively. To evaluate the developed method, equivalent model using finite element method was established and stress components of the method were compared with those of equivalent FE model. One of promising ATF concepts is the coated cladding, which take advantages such as high melting point, a high neutron economy, and low tritium permeation rate. To evaluate the mechanical behavior and performance of the coated cladding, we need to develop the specified model to simulate the ATF behaviors in the reactor. In particular, the model for simulation of stress and strain for the coated cladding should be developed because the previous model, which is 'FRACAS', is for one body model. The FRACAS module employs the analytical method based on thin walled theory. According to thin-walled theory, radial stress is defined as zero but this assumption is not suitable for ATF cladding because value of the radial stress is not negligible in the case of ATF cladding. Recently, a structural model for multi-layered ceramic cylinders based on thick-walled theory was developed. Also, FE-based numerical simulation such as BISON has been developed to evaluate fuel performance. An analytical method that calculates stress components of ATF cladding was developed in this study. Thick-walled theory was used to derive equations for calculating stress and strain. To solve for these equations, boundary and loading conditions were obtained by subroutine 'Cladf' and 'Couple' and applied to the analytical method. To evaluate the developed method, equivalent FE model was established and its results were compared to those of analytical model. Based on the

  16. The new self-supporting face brick façades

    Directory of Open Access Journals (Sweden)

    C. del Río

    2016-12-01

    Full Text Available The ‘Self-Supporting’ face brick façade is the result of a profound reflection on the different façade solutions that have been used throughout the last century for the pillar-structured buildings, and is based on the utilization of the potential that ceramic materials have when they work in compression. The construction solution consists in placing the entire outer sheet of the enclosure ahead of the building’s structure, so as to use the brick wall itself as its own supporting structure. This construction type eliminates the thermal bridges at façade-slab joints, and is more effective regarding mechanical behaviour than conventional solutions, since the own-weight effect contributes beneficially to stability against horizontal actions.

  17. Experimental and numerical investigation of a hollow brick filled with perlite insulation

    Energy Technology Data Exchange (ETDEWEB)

    Zukowski, M. [Department of Heat Engineering, Bialystok Technical University, Wiejska Street 45A, 15-351 Bialystok (Poland); Haese, G. [Wohnungsgenossenschaft Gartenheim eG, Hildesheimer Strasse 142 D-30173 Hannover (Germany)

    2010-09-15

    The present study is focused on the investigation of the effective thermal properties of a modern vertically perforated masonry unit filled with perlite insulation. Based on measurements and numerical calculations, the thermal performance of the new hollow brick was determined. The authors suggest to use the following parameters for this building material: equivalent heat capacity equal to 855.1 J/kg K, equivalent heat conductivity equal to 0.09 W/mK and equivalent density equal to 653.15 kg/m{sup 3}. The dependence of the equivalent thermal resistance of the whole wall made of this brick and mortar, is shown for different mortar joint thicknesses. All results, presented in this paper, can be used in energy balance calculations for buildings made of masonry unit. (author)

  18. Method for Improving Transverse Wall Thickness Precision of Seamless Steel Tube Based on Tube Rotation

    Institute of Scientific and Technical Information of China (English)

    Yong-zheng JIANG; Hua-ping TANG

    2015-01-01

    The tube rotation method (TRM) refers to the rotational movement of steel tube about its axis as well as translation in rolling direction in stretch reducing rolling process. The inlfuence of the TRM on transverse wall thickness precision of seamless steel tube was studied. Thickness distribution of the TRM was obtained by superimposing the thickened amount of single pass roll-ing. Results show that the TRM can effectively improve the evenness of thickness distribution. In order to analyze the inlfuence mechanism of the TRM, the ifnite element method was adopted to simulate the thickness distribution in stretch reduction process. Results show that the TRM changes the roundtrip lfow between two ifx places of conventional stretch reducing and inhibits the directional accumulation of metal. In addition, the TRM has a correction effect on thickness cusp. All these advantages of the TRM help to improve the transverse wall thickness precision of seamless steel tube.

  19. Assessment of air pollutant emissions from brick kilns

    Science.gov (United States)

    Rajarathnam, Uma; Athalye, Vasudev; Ragavan, Santhosh; Maithel, Sameer; Lalchandani, Dheeraj; Kumar, Sonal; Baum, Ellen; Weyant, Cheryl; Bond, Tami

    2014-12-01

    India has more than 100,000 brick kilns producing around 250 billion bricks annually. Indian brick industry is often a small scale industry and third largest consumer of coal in the country. With the growing demand for building materials and characterised by lack of pollution control measures the brick industry has a potential to cause adverse effects on the environment. This paper presents assessment of five brick making technologies based on the measurements carried out at seventeen individual brick kilns. Emissions of PM, SO2, CO and CO2 were measured and these emissions were used to estimate the emission factors for comparing the emissions across different fuel or operating conditions. Estimated emission from brick kilns in South Asia are about 0.94 million tonnes of PM; 3.9 million tonnes of CO and 127 million tonnes of CO2 per year. Among various technologies that are widely used in India, Zig zag and vertical shaft brick kilns showed better performance in terms of emissions over the traditional fixed chimney Bull's trench kilns. This suggests that the replacement of traditional technologies with Zig zag, vertical shaft brick kilns or other cleaner kiln technologies will contribute towards improvements in the environmental performance of brick kiln industry in the country. Zig zag kilns appear to be the logical replacement because of low capital investment, easy integration with the existing production process, and the possibility of retrofitting fixed chimney Bull's trench kilns into Zig zag firing.

  20. Are ceramics and bricks reliable absolute geomagnetic intensity carriers?

    Science.gov (United States)

    Morales, Juan; Goguitchaichvili, Avto; Aguilar-Reyes, Bertha; Pineda-Duran, Modesto; Camps, Pierre; Carvallo, Claire; Calvo-Rathert, Manuel

    2011-08-01

    A detailed rock-magnetic and archeointensity study was carried out on materials baked by a western Mexican artisan following traditional techniques to produce faithful reproductions of archeological pieces of the Michoacán region (Western Mesoamerica). The field strength at the site (41.0 ± 0.5 μT) was measured with a fluxgate magnetometer and the temperature of the furnace during the baking process was monitored continually by means of a thermocouple placed in the middle of the baking cavity. Rock-magnetic experiments performed on the raw material (clay and paste) and on insitu prepared baked ceramics and bricks included measurement of thermomagnetic curves (susceptibility and strong-field magnetization versus temperature), first-order reversal curves (FORC), anisotropy of magnetic susceptibility (AMS) and anisotropy of thermoremanent magnetization (A-TRM). Magnetite and probably hematite are present in the samples as carriers of the remanence. Hysteresis ratios suggest that the samples fall in the pseudo-single-domain grain size region, which may indicate a mixture of multi-domain and a significant amount of single-domain grains. Ceramic pieces and brick fragments were subjected to the Thellier-Coe archeointensity method and to an alternative paleointensity experiment, with a TRIAXE magnetometer, in order to check whether they are faithful recorders of the local geomagnetic field strength. Mean raw-intensity of sample M1 (pottery) overestimates a 7% the expected site intensity, while those corresponding to the brick samples (LQ1 and LQ2) underestimate it 15%. Brick sample LNQ shows a slightly lower intensity (7%), but agrees with the expected site intensity within the experimental uncertainty. The intensity retrieved from the volcanic fragment also included closely reproduces the expected intensity. After A-TRM and cooling-rate corrections, all mean raw values move closer to the expected intensity. Measurement of temperatures at different parts inside the kiln

  1. Device and method for treatment of openings in vascular and septal walls

    Energy Technology Data Exchange (ETDEWEB)

    Singhal, Pooja; Wilson, Thomas S.; Cosgriff-Hernandez, Elizabeth; Maitland, Duncan J.

    2017-06-06

    A device, system and method for treatment of an opening in vascular and/or septal walls including patent foramen ovale. The device has wings/stops on either end, an axis core covered in a shape memory foam and is deliverable via a catheter to the affected opening, finally expanding into a vascular or septal opening where it is held in place by the expandable shape memory stops or wings.

  2. Finite element modelling of the effect of temperature and neutron dose on the fracture behaviour of nuclear reactor graphite bricks

    Energy Technology Data Exchange (ETDEWEB)

    Wadsworth, M.; Kyaw, S.T., E-mail: si.kyaw@nottingham.ac.uk; Sun, W.

    2014-12-15

    Highlights: • Effects of irradiation on fracture behaviours of graphite bricks are analysed. • Two irradiation conditions chosen are irradiation temperature and neutron dose. • The crack initiates around the keyway fillet of the brick for every study. • Higher temperature and higher neutron dose accelerate crack initiation time. • Turnaround point of hoop strain indicates the crack initiation time. - Abstract: Graphite moderator bricks used within many UK gas-cooled nuclear reactors undergo harsh temperature and radiation gradients. They cause changes in material properties of graphite over extended periods of time. Consequently, models have been developed in order to understand and predict the complex stresses formed within the brick by these processes. In this paper the effect of irradiation temperature and neutron dose on the fracture characteristics, crack initiation and crack growth are investigated. A finite element (FE) mechanical constitutive model is implemented in combination with the damage model to simulate crack growth within the graphite brick. The damage model is based on a linear traction–separation cohesive model in conjunction with the extended finite element method for arbitrary crack initiation and propagation. Results obtained have showed that cracks initiate in the vicinity of the keyway fillet of the graphite brick and initiation time accelerates with higher temperatures and doses.

  3. [Determination of life elements in hair and urine with brick-tea fluorosis in Inner Mongolia by ICP-OES].

    Science.gov (United States)

    Hou, Kun; Ji, Hong-bing; Li, Hai-rong; Wang, Li-zhen; Wang, Wu-yi; Liu, Qing-bin; Wang, Ge; Liu, Xue-hui

    2009-04-01

    In brick-tea fluorosis affected areas XiLinHot city in Inner Mongolia, herdsmen who like drinking a large amount of brick tea in everyday life and Han habitants rarely drinking brick tea as control group were enrolled, and their hair and urine were sampled. The concentrations of Ca, Mg, K, Al, P, Cu, Zn and Fe in hair and urine were detected using ICP-OES. The RSDs of the method were between 2.32% and 8.03%, and the analytical results of the hair reference samples were consistent with the certified values. The results showed that the contents of Al, Mg and K in hair, and contents of Al and Ca in urine of herdsmen who were accustomed to drinking brick tea were obviously higher than those in control group (Pbrick tea was lower than those in control group (P0.05). Chronically drinking brick tea probably brings metabolic disorder of Ca and Al in human body, and the interaction mechanism of life elements in brick-tea fluorosis should be further studied.

  4. Redesigned Surface Based Machining Strategy and Method in Peripheral Milling of Thin-walled Parts

    Institute of Scientific and Technical Information of China (English)

    JIA Zhenyuan; GUO Qiang; SUN Yuwen; GUO Dongming

    2010-01-01

    Currently, simultaneously ensuring the machining accuracy and efficiency of thin-walled structures especially high performance parts still remains a challenge. Existing compensating methods are mainly focusing on 3-aixs machining, which sometimes only take one given point as the compensative point at each given cutter location. This paper presents a redesigned surface based machining strategy for peripheral milling of thin-walled parts. Based on an improved cutting force/heat model and finite element method(FEM) simulation environment, a deflection error prediction model, which takes sequence of cutter contact lines as compensation targets, is established. And an iterative algorithm is presented to determine feasible cutter axis positions. The final redesigned surface is subsequently generated by skinning all discrete cutter axis vectors after compensating by using the proposed algorithm. The proposed machining strategy incorporates the thermo-mechanical coupled effect in deflection prediction, and is also validated with flank milling experiment by using five-axis machine tool. At the same time, the deformation error is detected by using three-coordinate measuring machine. Error prediction values and experimental results indicate that they have a good consistency and the proposed approach is able to significantly reduce the dimension error under the same machining conditions compared with conventional methods. The proposed machining strategy has potential in high-efficiency precision machining of thin-walled parts.

  5. A nondestructive method for diagnosis of insulated building walls using infrared thermography in real situation

    Science.gov (United States)

    Larbi Youcef, Mohamed H. A.; Mazioud, Atef; Bremond, Pierre; Ibos, Laurent; Candau, Yves; Piro, Michel; Filloux, Alain

    2008-03-01

    In order to provide a method to control conformity of insulation of buildings after restoration, Protomeres project was launched under Prebat 2005 program. This work deals with the development of an experimental protocol for the diagnostic of multi-layered insulated building walls. In a previous study, a test bench was set up in order to measure front and back side temperatures of standard panels compounded of 1cm of plaster and various thicknesses of polystyrene. The panels considered have insulation thicknesses of 2, 6 and 10cm. In the present work, the panels are fixed on walls in laboratory to test real situations in constructions. The front side is painted in standardized black color and heated by two halogen lamps of 500W. A CEDIP Jade Long wave infrared camera and thermocouples are used to carry out temperature measurements during an exposure time and subsequent cooling. In a second time, a one dimensional model based on thermal quadruples and Laplace transforms was developed under Matlab environment. This model simulates a three-layered wall with a blade of air between polystyrene and concrete. Finally, a method of identification of physical parameters is implemented by performing least square minimization based on Levenberg-Marquardt method. The experimental measurements are compared to theoretical results and by minimization we obtain thermal conductivity and diffusivity as well as thickness of the two layers.

  6. Reduction of heating energy demand of residential buildings and of gas emission relevant for the greenhouse effect by using sand-lime building material in order to avoid thermal bridges in brick wall construction. Final report; Reduzierung des Heizenergiebedarfs von Wohngebaeuden und der Emissionen treibhausrelevanter Gase durch Einsatz von Kalksand-Spezialbaustoffen zur Vermeidung von Waermebruecken im Mauerwerksbau. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Eden, W. [Forschungsvereinigung ' Kalk-Sand' e.V., Hannover (Germany); Buhl, J.C. [Hannover Univ. (Germany). Inst. fuer Mineralogie

    2001-11-01

    The yearly energy consumption in the Federal Republic of Germany in the field of space heating still amounts to 30% of the yearly overall energy consumption. The sand-lime brick industry has the opportunity to make a contribution to energy conservation by avoiding too high heat flows over thermal bridges. Detailed constructional solutions do not always suffice to minimise the effects of thermal bridges. The use of bricks with low thermal conductivity and simultaneous high stone pressure resistance is useful for all detailed solutions. The influence of environmentally friendly, available and technically perfect lightweight aggregates for the production of sand-lime bricks has been investigated systematically and in detail in the frame of this research project. The main target of the project is to guarantee the manufacturing of bricks with high norm pressure resistance and simultaneous low thermal conductivity. This research target has been reached. (orig.) [German] Der jaehrliche Energieverbrauch in der Bundesrepublik Deutschland fuer den Sektor Raumwaerme betraegt immer noch ca. 30% vom jaehrlichen Gesamtenergieverbrauch. Fuer die Kalksandsteinindustrie besteht die Moeglichkeit, einen Beitrag zur Energieeinsparung durch Vermeidung von erhoehten Waermestroemen ueber Waermebruecken zu leisten. Nicht immer sind rein konstruktive Detailloesungen ausreichend, um die Auswirkung von Waermebruecken zu minimieren. Bei allen Detailpunkten ist der Einsatz von Mauersteinen mit einer niedrigen Waermeleitfaehigkeit und gleichzeitig einer hohen Steindruckfestigkeit sinnvoll. Mit dem Forschungsvorhaben wurde zum einen der Einfluss umweltfreundlicher, verfuegbarer und technisch einwandfreier Leichtzuschlaege fuer die Herstellung von Kalksand-Leichtsteinen systematisch und detailliert untersucht. Hauptziel dieses Projektes ist es, Mauersteine mit einer hohen Normdruckfestigkeit bei gleichzeitig niedriger Waermeleitfaehigkeit sicher herzustellen. Das Forschungsziel wurde erreicht

  7. Al2O3-SiC-C Bricks for Hot Metal Pretreatment

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ 1 Scope This standard specifies the classification,techni-cal requirements,test methods,inspection rules,packing,marking,transportation,storage and quality certificate of Al2O3-SiC-C bricks for hot metal pre-treatment.

  8. Chinese Standards on Refractories Magnesia Carbon Bricks GB/T 22589-2008

    Institute of Scientific and Technical Information of China (English)

    Yu Lingyan; Peng Xigao

    2010-01-01

    @@ 1 Scope This standard specifies the classification,techni-cal requirements,test methods,quality appraisal pro-cedures,packing,marking,transportation,storage,and quality certificate of magnesia carbon bricks. This standard is applicable to the magnesia carbonbricks for steel-making converter,electric furnace,la-dle(refining furnace),etc.

  9. Al2O3 SiC-C Bricks for Hot Metal Pretreatment

    Institute of Scientific and Technical Information of China (English)

    Yu Lingyan; Peng Xigao

    2010-01-01

    @@ 1 Scope This standard specifies the classification,shape and dimensions,technical requirements,test methods,quality appraisal procedures,packing,marking,transportation,storage,and quality certificate of Al2O3SiC-C bricks for hot metal pretreatment.

  10. Cordierite Bricks for Ceramic Burner of Hot Blast Stove YB/T 4128-2005

    Institute of Scientific and Technical Information of China (English)

    Zhang Xiaohui; Chai Junlan

    2009-01-01

    @@ 1 Scope This standard specifies the classification,brand,technical requirements,shape and dimension,test method,quality appraisal procedure,packing,marking,transportation,storage and quality certificate of cordierite bricks for ceramic burner of blast furnace and hot blast stove.

  11. Development of digital image correlation method to analyse crack variations of masonry wall

    Indian Academy of Sciences (India)

    Shih-Heng Tung; Ming-Hsiang Shih; Wen-Pei Sung

    2008-12-01

    The detection of crack development in a masonry wall forms an important study for investigating the earthquake resistance capability of the masonry structures. Traditionally, inspecting the structure and documenting the findings were done manually. The procedures are time-consuming, and the results are sometimes inaccurate. Therefore, the digital image correlation (DIC) technique is developed to identify the strain and crack variations. This technique is non-destructive for inspecting the whole displacement and strain field. Tests on two masonry wall samples were performed to verify the performance of the digital image correlation method. The phenomena of micro cracks, strain concentration situation and nonuniform deformation distribution which could not have been observed preciously by manual inspection are successfully identified using DIC. The crack formation tendencies on masonry wall can be observed at an earlier stage by this proposed method. These results show a great application potential of the DIC technique for various situations such as inspecting shrinkage-induced cracks in fresh concrete, masonry and reinforced concrete structures, and safety of bridges.

  12. Use Of Crushed Bricks As Coarse Aggregate In Concrete

    Directory of Open Access Journals (Sweden)

    Fadia S. Kalak

    2013-05-01

    Full Text Available The investigation reported in this paper is carried out to study the feasibility of using crushed bricks to substitute the coarse aggregate (gravel in concrete. Two types of concrete mixing are prepared. The first one is a mixture of  1:2:4 without crushed bricks and is used as a reference mixture .The second one is made of different weight of crushed bricks (as a percentage from the weight of the coarse aggregate. A total of 30 numbers of concrete specimens are casted with and without crushed bricks and  tested under compression and split tension as per relevant to British standard specifications.Test results indicated that using crushed bricks reduces the strength of concrete. Also, the percentage of water to cement ratio increases for constant slump when the percentage of crushed bricks increased.

  13. Urban-environmental study from the Juarez municipality brick factories

    Directory of Open Access Journals (Sweden)

    María de Lourdes Romo Aguilar

    2004-01-01

    Full Text Available This paper seeks to evaluate the current situation of the traditional and ecological brick kilns in Juarez. The evaluation is addressed in both the environmental and socio-economic context. The brick production belongs to the informal economic sector without any regulatory scheme and without taxation. Its very low technology has serious impacts on the binational environment of the Paso del Norte region, through the highly polluted emissions to the atmosphere. However, the social and economic context of people working in this industry does not allow important changes, thus, making difficult any initiative for the brick kilns improvements and relocation. The main information source was a very concise survey applied to whole universe of brick makers. Data survey was registered in a Geographic Information System (GIS environment allowing us the analysis of the brick kilns in a spatial context. Finally, this document presents a descriptive profile of the brick kilns production and for the brickmakers.

  14. Methods for monitoring heat flow intensity in the blast furnace wall

    Directory of Open Access Journals (Sweden)

    L'. Dorčák

    2010-04-01

    Full Text Available In this paper we present the main features of an online system for real-time monitoring of the bottom part of the blast furnace. Firstly, monitoring concerns the furnace walls and furnace bottom temperatures measurement and their visualization. Secondly, monitored are the heat flows of the furnace walls and furnace bottom. In the case of two measured temperatures, the heat flow is calculated using multi-layer implicit difference scheme and in the case of only one measured temperature, the heat flow is calculated using a method based on application of fractional-order derivatives. Thirdly, monitored is the theoretical temperature of the blast furnace combustion process in the area of tuyeres.

  15. Thickness measuring of electroconductive pipe walls using the dual-frequency eddy-current method

    Science.gov (United States)

    Yakimov, Evgeny; Galtseva, Olga; Ustyugov, Daniil

    2017-01-01

    The paper describes a dual-frequency method for reducing the impact of changes in the gap size between the eddy-current transducer and the pipe, as well as the pipe electrical conductivity on the eddy-current thickness gauge readings. A block-diagram of the dual-frequency eddy-current thickness gauge is proposed for light-alloy drill pipes. The amplitude and signal phase dependencies on the wall thickness in the range from 6 to 17 mm and the gap in the range from 0 to 13.5 mm were studied, the results are presented. The digital signal processing algorithms based on the piecewise-linear approximation of low-frequency and high-frequency signal phase dependencies on the wall thickness are proposed. It is shown that the proposed correction algorithms can reduce the error caused by variations of electrical conductivity and the gap between the transducer and the pipe.

  16. Brane brick models in the mirror

    Science.gov (United States)

    Franco, Sebastián; Lee, Sangmin; Seong, Rak-Kyeong; Vafa, Cumrun

    2017-02-01

    Brane brick models are Type IIA brane configurations that encode the 2 d N=(0,2) gauge theories on the worldvolume of D1-branes probing toric Calabi-Yau 4-folds. We use mirror symmetry to improve our understanding of this correspondence and to provide a systematic approach for constructing brane brick models starting from geometry. The mirror configuration consists of D5-branes wrapping 4-spheres and the gauge theory is determined by how they intersect. We also explain how 2 d (0 , 2) triality is realized in terms of geometric transitions in the mirror geometry. Mirror symmetry leads to a geometric unification of dualities in different dimensions, where the order of duality is n - 1 for a Calabi-Yau n-fold. This makes us conjecture the existence of a quadrality symmetry in 0 d. Finally, we comment on how the M-theory lift of brane brick models connects to the classification of 2 d (0 , 2) theories in terms of 4-manifolds.

  17. Brane Brick Models in the Mirror

    CERN Document Server

    Franco, Sebastian; Seong, Rak-Kyeong; Vafa, Cumrun

    2016-01-01

    Brane brick models are Type IIA brane configurations that encode the $2d$ $\\mathcal{N}=(0,2)$ gauge theories on the worldvolume of D1-branes probing toric Calabi-Yau 4-folds. We use mirror symmetry to improve our understanding of this correspondence and to provide a systematic approach for constructing brane brick models starting from geometry. The mirror configuration consists of D5-branes wrapping 4-spheres and the gauge theory is determined by how they intersect. We also explain how $2d$ $(0,2)$ triality is realized in terms of geometric transitions in the mirror geometry. Mirror symmetry leads to a geometric unification of dualities in different dimensions, where the order of duality is $n-1$ for a Calabi-Yau $n$-fold. This makes us conjecture the existence of a quadrality symmetry in $0d$. Finally, we comment on how the M-theory lift of brane brick models connects to the classification of $2d$ $(0,2)$ theories in terms of 4-manifolds.

  18. DEVELOPMENT OF DUAL ANCHORED SHEET PILE WALL METHOD TO INCREASE FRONT WATER DEPTH AND SEISMIC RESISTANCE OF EXISTING QUAY

    Science.gov (United States)

    Nakamura, Yasushi; Sato, Masakatsu; Kikuchi, Yoshiaki; Sugano, Takahiro; Morikawa, Yoshiyuki; Hoshino, Masami; Miki, Kenichi

    Recently the dual anchored sheet pile wall method has been developed to increase a front water depth and seismic resistance of existing quay walls by providing an additional anchor in the lower level of them to reduce a flexural moment of the sheet piles and a tension of the anchors. The existing technical information is not enough to evaluate the seismic behavior and the retrofit of the quay walls with anchors at two different levels. Therefore the experiments with a scale model set on the vibration table of the centrifugal apparatus as well as two dimensional effective stress analyses have been mobilized to investigate the seismic retrofit of the dual anchored sheet pile wall. The experiments and analyses demonstrate the increase the earthquake resistance of quay walls, because they showed the additional anchor can reduce the stress of the sheet walls to one half.

  19. Building the Platform of Digital Earth with Sphere Split Bricks

    Directory of Open Access Journals (Sweden)

    WANG Jinxin

    2015-06-01

    Full Text Available Discrete global grids, a modeling framework for big geo-spatial data, is always used to build the Digital Earth platform. Based on the sphere split bricks (Earth system spatial grids, it can not only build the true three-dimensional digital Earth model, but also can achieve integration, fusion, expression and application of the spatial data which locates on, under or above the Earth subsurface. The theoretical system of spheroid geodesic QTM octree grid is discussed, including the partition principle, analysis of grid geometry features and coding/ decoding method etc, and a prototype system of true-3D digital Earth platform with the sphere split bricks is developed. The functions of the system mainly include the arbitrary sphere segmentation and the visualization of physical models of underground, surface and aerial entities. Results show that the sphere geodesic QTM octree grid has many application advantages, such as simple subdivision rules, the grid system neat, clear geometric features, strong applicability etc. In particular, it can be extended to the ellipsoid, so it can be used for organization, management, integration and application of the global spatial big data.

  20. Properties of bricks produced from Greenlandic marine sediments

    DEFF Research Database (Denmark)

    Bertelsen, Ida Maria Gieysztor; Belmonte, Louise Josefine; Chen, Wan

    2015-01-01

    This study investigated the possibility of a local brick production from fine grained marine sediments (MS) near Sisimiut, Greenland. The assessment is based on the physical and mechanical properties of clay bricks concerning the resistance to the harsh, Arctic weather conditions, together...... water to fulfil the requirements for severe weathering according to ASTM-C62 (2013). It was concluded that the firing temperature needed to be increased in order to obtain a more durable brick-type, suitable for the Arctic climate....

  1. Enhancement in thermal and mechanical properties of bricks

    OpenAIRE

    Shibib Khalid S.; Qatta Haqi I.; Hamza Mohammed S.

    2013-01-01

    A new type of porous brick is proposed. Sawdust is initially well mixed with wet clay in order to create voids inside the brick during the firing process. The voids will enhance the total performance of the brick due to the reduction of its density and thermal conductivity and a minor reduction of its compressive stress. All these properties have been measured experimentally and good performance has been obtained. Although a minor reduction in compressive s...

  2. Technology Solutions Case Study: Retrofit Measures for Embedded Wood Members in Insulated Mass Masonry Walls

    Energy Technology Data Exchange (ETDEWEB)

    K. Ueno

    2015-10-01

    In this project, the Building Science Corporation team studied a historic brick building in Lawrence, Massachusetts, which is being renovated into 10 condominium units and adding insulation to the interior side of walls of such masonry buildings.

  3. New Method Developed To Purify Single Wall Carbon Nanotubes for Aerospace Applications

    Science.gov (United States)

    Lebron, Marisabel; Meador, Michael A.

    2003-01-01

    Single wall carbon nanotubes have attracted considerable attention because of their remarkable mechanical properties and electrical and thermal conductivities. Use of these materials as primary or secondary reinforcements in polymers or ceramics could lead to new materials with significantly enhanced mechanical strength and electrical and thermal conductivity. Use of carbon-nanotube-reinforced materials in aerospace components will enable substantial reductions in component weight and improvements in durability and safety. Potential applications for single wall carbon nanotubes include lightweight components for vehicle structures and propulsion systems, fuel cell components (bipolar plates and electrodes) and battery electrodes, and ultra-lightweight materials for use in solar sails. A major barrier to the successful use of carbon nanotubes in these components is the need for methods to economically produce pure carbon nanotubes in large enough quantities to not only evaluate their suitability for certain applications but also produce actual components. Most carbon nanotube synthesis methods, including the HiPCO (high pressure carbon monoxide) method developed by Smalley and others, employ metal catalysts that remain trapped in the final product. These catalyst impurities can affect nanotube properties and accelerate their decomposition. The development of techniques to remove most, if not all, of these impurities is essential to their successful use in practical applications. A new method has been developed at the NASA Glenn Research Center to purify gram-scale quantities of single wall carbon nanotubes. This method, a modification of a gas phase purification technique previously reported by Smalley and others, uses a combination of high-temperature oxidations and repeated extractions with nitric and hydrochloric acid. This improved procedure significantly reduces the amount of impurities (catalyst and nonnanotube forms of carbon) within the nanotubes, increasing

  4. Production and Development of LRCO‘s Silica Bricks

    Institute of Scientific and Technical Information of China (English)

    MAXianghong; LIZhenmin; 等

    1998-01-01

    This paper reviews the history of development and production of silica bricks at Luoyang Refrac-tories(Group) Co.,Ltd,(Former Luoyang Refrac-tories Factory). Through the improvement and in-troducing technology from abroad the company's management and quality standard on silica bricks production has reached a higher level.The physical and chemical specifications,as well as the appear-ance of silica bricks for coke ovens,hot blast stoves and glass kilns have reached the advanced interna-tional level.Now the company has become producing base and main exporting base various kinds of silica bricks in China.

  5. Frost resistance of concrete with crushed brick as aggregate

    Directory of Open Access Journals (Sweden)

    Janković Ksenija

    2010-01-01

    Full Text Available The investigation included concrete made by using recycled brick as aggregate. Experimental work included several types of concrete made with the same cement content (385 kg/m3, and same consistency (slump about 1 cm. Recycled brick and combination of natural river aggregate and recycled brick were used as aggregates. The influence of percentage and grain size of crushed brick aggregate on concrete compressive strength, water absorption and frost resistance were observed. On the basis of the results obtained during experimental research, a general conclusion can be drawn that the application of recycled concrete as aggregate can lead to new composites with satisfactory physical-mechanical properties.

  6. An Overview of Rha And Scba Clay Bricks

    Directory of Open Access Journals (Sweden)

    Er. Ravindra Kumar,

    2016-12-01

    Full Text Available Burnt clay brick is one of the major and widely used building units in construction around the world. The manufacturing of burnt clay bricks using waste materials can minimize the environmental overburden caused by waste deposition on open landfills and would also improve the brick performance at low production cost leading to more sustainable construction. These wastes utilization would not only be economical, but may also help to create a sustainable and pollution free environment. This study aims to evaluate the effect of the waste addition produced from two major crops: sugarcane and rice in clay bricks manufacturing.

  7. An analytical method for calculating torsional constants for arbitrary complicated thin-walled cross-sections

    Institute of Scientific and Technical Information of China (English)

    DU Baisong; GE Yaojun; ZHOU Zheng

    2007-01-01

    In this paper,an analytical method is proposed for calculating torsional constants for complicated thin-walled cross-sections with arbitrary closed or open rib stiffeners.This method uses the free torsional theory and the principle of virtual work to build goveming equilibrium equations involving unknown shear flows and twisting rate.After changing the form of the equations and combining these two unknowns into one,torsional function,which is a function of shear flow,shear modulus,and twisting rate,is included in the governing equations as only one of the unknowns.All the torsional functions can be easily obtained from these homogeneous linear equations,and torsional constants can be easily obtained from the torsional functions.The advantage of this method is that we can easily and directly obtain torsional constants from the torsional functions,rather than the more sophisticated shear flow and twisting rate calculations.Finally,a complicated thin-walled cross-section is given as a valid numerical example to verify the analytical method,which is much more accurate and simpler than the traditional finite element method.

  8. Experimental results on a wall interference correction method with interface measurements

    Science.gov (United States)

    Lo, C. F.; Ulbrich, N.

    1992-01-01

    A wall interference assessment and correction method for subsonic two-dimensional wind tunnel testing is presented. This method calculates a pressure coefficient and angle of attack correction based on velocity measurements on interfaces inside of the wind tunnel. A mathematical representation of the test article is not required. An experimental verification of the suggested technique is given. A NACA 0012 airfoil is tested at a Mach number of 0.70 and at two different angles of attack. Calculated blockage corrections show reasonable agreement with results based on Hackett's method. Corrected surface pressures compare favorably to free-air flow field data if the tunnel flow field is subsonic. The present wall interference correction method can be applied to transonic tunnel flow fields with some restrictions. Errors are estimated and it is shown that the expected error in calculating the pressure coefficient correction on the model surface is in the order of the error of pressure coefficient measurement on interfaces. Necessary testing equipment in existing tunnels can easily be modified if the present method is applied.

  9. Analysis of heat transfer properties of three-layer wall with phase-change heat storage in solar greenhouse%日光温室三重结构相变蓄热墙体传热特性分析

    Institute of Scientific and Technical Information of China (English)

    管勇; 陈超; 凌浩恕; 韩云全; 闫全英

    2013-01-01

    At present, the wall structures of a Chinese solar greenhouse puts more emphasis upon wall thermal insulation than on heat storage of the wall, such as, brick wall / air layer / brick wall (indoor), brick wall /polystyrene board/brick wall (indoor), rammed earth wall/brick wall (indoor), and so on. In order to solve the problems which existed in the thermal performance design method of the wall structure in a solar greenhouse, the construction method of a three-layer wall with phase-change thermal storage, that is, the inner wall built with the phase change material (PCM) wallboard, the outer insulating layer built with polystyrene board and the middle layer built with block bricks, was proposed in this paper. To quantitatively evaluate the heat transfer performances and heat storage/release characteristics of the three-layer wall, an experimental device used for the heat performance of the three-layer wall was constructed at a vegetable planting base located in Beijing. Combined with the experimental results, the analysis method of heat transfer performances of solar greenhouse wall and its evaluation indexes were put forward. The analysis results showed that: 1) The three-layer wall had better heat storage/release performance than the traditional brick wall of the reference greenhouse. The PCM wallboard can significantly improve the utilization rate of solar energy and increase the indoor air temperature. The effective heat storage capacity of the three-layer wall was increased by 26.6% more than the north wall of the reference greenhouse in which the daily accumulation of solar radiation was 9.32 MJ/m2. At night, the cumulative heating capacity of the three-layer wall was increased by 16.2% over the capacity of the brick wall of the reference greenhouse during the time when the heat preservation quilt was closed. Moreover, the effective heat storage capacity of the per unit volume PCM wallboard was 80.0 MJ/m3 and it was about 10 times that of the block brick in

  10. Simplified method for the design of cylinder water walls for passive solar heating

    Energy Technology Data Exchange (ETDEWEB)

    van der Mersch, P.L.; Burns, P.J.; Winn, C.B.

    1981-01-01

    A cylinder water wall (CWW) system is considered. The design method allows for direct-gain space above and between the cylinders, which none of the current known design methods include. The design method consists of using design curves, and is oriented to the architectural community. At most, a four-function calculator is necessary. It requires knowing the room dimensions and the room UA and thermal capacitance. Two cylinder sizes and four cylinder spacings may be considered. The method permits determining the size of the glazing, how many cylinders of a given size are required and what spacing is necessary to maintain a desired average minimum, overall average and average maximum temperature in the room. An overview is given of how the design method was developed, as well as a description of how it is applied.

  11. Prediction Method of Seismic Residual Deformation of Caisson Quay Wall in Liquefied Foundation

    Institute of Scientific and Technical Information of China (English)

    WANG Li-yan; LIU Han-long; JIANG Peng-ming; CHEN Xiang-xiang

    2011-01-01

    The multi-spring shear mechanism plastic model in this paper is defined in strain space to simulate pore pressure generation and development in sands under cyclic loading and undrained conditions,and the rotation of principal stresses can also be simulated by the model with cyclic behavior of anisotropic consolidated sands.Seismic residual deformations of typical caisson quay walls under different engineering situations are analyzed in detail by the plastic model,and then an index of liquefaction extent is applied to describe the regularity of seismic residual deformation of caisson quay wall top under different engineering situations.Some correlated prediction formulas are derived from the results of regression analysis between seismic residual deformation of quay wall top and extent of liquefaction in the relative safety backfill sand site.Finally,the rationality and the reliability of the prediction methods are validated by test results of a 120 g-centrifuge shaking table,and the comparisons show that some reliable seismic residual deformation of caisson quay can be predicted by appropriate prediction formulas and appropriate index of liquefaction extent.

  12. [Hematoma of the abdominal wall. A case report: pitfall of Seldinger method via femoral artery].

    Science.gov (United States)

    Hiramatsu, Hisaya; Sugiura, Yasushi; Takeda, Ririko; Nanba, Hiroki

    2009-02-01

    We reported a case of an abdominal wall hematoma which caused by Seldinger method via the femoral artery. A 48-year-old female, suffered from direct carotid cavernous fistula, was treated by transfemoral transvenous embolization (TVE). The whole procedure was completed without difficulty except minor resistance of guide wire manipulation during left femoral artery catheterization. Four hours later, the patient became hypotensive and showed the sign of impending shock without definitive causes. Nine hours after the embolization a huge hematoma of the abdominal wall was found. It required the total 1200 m/ of blood transfusion before her blood pressure returned to normal. She recovered fully from this event and discharged uneventfully. There is a speculation that a deep circumflex iliac artery (DCIA) was injured with an angle-shaped guide wire and bled into the abdominal wall. And subsequent systemic heparinization prevented the coagulation process, resulting a large hematoma. Anatomically, an angle-shaped guide wire is easily able to migrate into DCIA. To prevent a vascular injury, it is very important to manipulate a guide wire under fluoroscopic control and to select a J-shaped guide wire instead of an angle-shaped one.

  13. Calculation of Reaction Forces in the Boiler Supports Using the Method of Equivalent Stiffness of Membrane Wall

    Directory of Open Access Journals (Sweden)

    Josip Sertić

    2014-01-01

    Full Text Available The values of reaction forces in the boiler supports are the basis for the dimensioning of bearing steel structure of steam boiler. In this paper, the application of the method of equivalent stiffness of membrane wall is proposed for the calculation of reaction forces. The method of equalizing displacement, as the method of homogenization of membrane wall stiffness, was applied. On the example of “Milano” boiler, using the finite element method, the calculation of reactions in the supports for the real geometry discretized by the shell finite element was made. The second calculation was performed with the assumption of ideal stiffness of membrane walls and the third using the method of equivalent stiffness of membrane wall. In the third case, the membrane walls are approximated by the equivalent orthotropic plate. The approximation of membrane wall stiffness is achieved using the elasticity matrix of equivalent orthotropic plate at the level of finite element. The obtained results were compared, and the advantages of using the method of equivalent stiffness of membrane wall for the calculation of reactions in the boiler supports were emphasized.

  14. Calculation of reaction forces in the boiler supports using the method of equivalent stiffness of membrane wall.

    Science.gov (United States)

    Sertić, Josip; Kozak, Dražan; Samardžić, Ivan

    2014-01-01

    The values of reaction forces in the boiler supports are the basis for the dimensioning of bearing steel structure of steam boiler. In this paper, the application of the method of equivalent stiffness of membrane wall is proposed for the calculation of reaction forces. The method of equalizing displacement, as the method of homogenization of membrane wall stiffness, was applied. On the example of "Milano" boiler, using the finite element method, the calculation of reactions in the supports for the real geometry discretized by the shell finite element was made. The second calculation was performed with the assumption of ideal stiffness of membrane walls and the third using the method of equivalent stiffness of membrane wall. In the third case, the membrane walls are approximated by the equivalent orthotropic plate. The approximation of membrane wall stiffness is achieved using the elasticity matrix of equivalent orthotropic plate at the level of finite element. The obtained results were compared, and the advantages of using the method of equivalent stiffness of membrane wall for the calculation of reactions in the boiler supports were emphasized.

  15. CONDITION OF VEGETATION ON THE GREEN WALL WITH THE USE OF REMOTE SENSING METHODS

    Directory of Open Access Journals (Sweden)

    Daniel Skarżyński

    2015-07-01

    Full Text Available Research on the possibility of using remote sensing methods to evaluate condition of vegetation on the green walls were performed on experimental models in 2010–2011. Two models that differ from one another with vegetation layer were analyzed: a retention model (MR I with substrate soil and an economic model (ME II with hydroponic felt. In the individual panels plants representing shrubs, perennials and grasses were planted. In total, on experimental models 60 plant species was applied depending on the exhibition of the walls. The evaluation of the plants condition was performed based on field observations and the analysis of Normalized Difference Vegetation Index (NDVI. Evaluation of vegetation condition using remote sensing methods leads to the conclusion that the vegetation on retention model (MR I have a much higher NDVI index value compared with the economic model (ME II. The comparison of the percent coverage of panels on retention model (MR I and economic model (ME II by the plants was done by separating the background plane from the plant surface. As a division criterion NDVI ratio in the range from -1 to 0.2 was taken. The results showed a clear contrast between the level of plant coverage of the examined models for individual facades. On the retention model (MR I panels plant covering was significantly higher than on an economic model (ME II where plant growth was limited. The growth of vegetation on the retention model (MR I using substrate soil in plant panels was normal suggesting the potential use of such solutions in the climatic conditions of Lower Silesia. Vegetation on the economic model (ME II is characterized by a worse growth throughout the growing season, which is why it is not recommended. The study showed that it is possible to evaluate the conditions of vegetation on the green walls with the use of remote sensing methods based on a modified photographic camera.

  16. A simple and effective method for vegetative propagation of an endangered medicinal plant Salacia oblonga Wall.

    Science.gov (United States)

    Deepak, K G K; Suneetha, G; Surekha, Ch

    2016-01-01

    Salacia oblonga Wall. is an endangered medicinal plant whose conservation is urgently needed, as it is extensively used in the Indian Ayurvedic system of medicine to treat diabetes mellitus. This study shows an easy, effective and simple method of conserving genetic identity and producing elite clones of S. oblonga through vegetative propagation. Vegetative propagation was achieved using roots (R), stems with leaves (SL) and stems without leaves (S) with different concentrations (0-500 ppm) of indole butyric acid (IBA). Explants S and SL showed maximum shooting response with 300 ppm IBA and explant R showed maximum response with 200 ppm IBA.

  17. Investigation of mass transfer between two parallel walls at different temperatures by a moment method

    Science.gov (United States)

    Sloat, T. N.; Edwards, R. H.; Collins, R. L.

    1971-01-01

    One-dimensional flow between two fixed parallel walls composed of the same substance but at different temperatures and spaced a distance 1 apart is considered. The hot plate is the evaporating surface (source) and the cold plate is the condensing surface (sink). The vapor between the two plates is assumed to be a monatomic gas consisting of Maxwell molecules. Lee's moment method is used to obtain a set of six nonlinear equations. Both the nonlinear equations and a linearized approximation to them are solved.

  18. Synthesis of single-walled carbon nanotubes by the vertical floating catalyst method

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The vertical floating catalyst method is first used to produce single-walled carbon nanotubes (SWNTs)continuously on a large scale by a newly developed technique and pyrolysis of n-hexane. Diameter distributions, microstructure and purity of the SWNTs film, rope and web are measured by Raman spectroscopy and electron microscope.The results show that SWNTs product has a high degree of orientation, a wide distribution of diameters (0.7-2.0 nm)and high purity of > 80%.``

  19. Switching of transmission resonances in a two-channels coupler: A Boundary Wall Method scattering study

    Science.gov (United States)

    Nunes, A.; Zanetti, F. M.; Lyra, M. L.

    2016-10-01

    In this work, we study the transmission characteristics of a two-channels coupler model system using the Boundary Wall Method (BWM) to determine the solution of the corresponding scattering problem of an incident plane wave. We show that the BWM provides detailed information regarding the transmission resonances. In particular, we focus on the case of single channel input aiming to explore the energy switching performance of the coupler. We show that the coupler geometry can be tailored to allow for the first transmission resonances to be predominantly transmitted on specific output channels, an important characteristic for the realization of logical operations.

  20. A core-monitoring based methodology for predictions of graphite weight loss in AGR moderator bricks

    Energy Technology Data Exchange (ETDEWEB)

    McNally, K., E-mail: kevin.mcnally@hsl.gsi.gov.uk [Health and Safety Laboratory, Harpur Hill, Buxton, Derbyshire SK17 9JN (United Kingdom); Warren, N. [Health and Safety Laboratory, Harpur Hill, Buxton, Derbyshire SK17 9JN (United Kingdom); Fahad, M.; Hall, G.; Marsden, B.J. [Nuclear Graphite Research Group, School of MACE, University of Manchester, Manchester M13 9PL (United Kingdom)

    2017-04-01

    Highlights: • A statistically-based methodology for estimating graphite density is presented. • Graphite shrinkage is accounted for using a finite element model. • Differences in weight loss forecasts were found when compared to the existing model. - Abstract: Physically based models, resolved using the finite element (FE) method are often used to model changes in dimensions and the associated stress fields of graphite moderator bricks within a reactor. These models require inputs that describe the loading conditions (temperature, fluence and weight loss ‘field variables’), and coded relationships describing the behaviour of graphite under these conditions. The weight loss field variables are calculated using a reactor chemistry/physics code FEAT DIFFUSE. In this work the authors consider an alternative data source of weight loss: that from a longitudinal dataset of density measurements made on small samples trepanned from operating reactors during statutory outages. A nonlinear mixed-effect model is presented for modelling the age and depth-related trends in density. A correction that accounts for irradiation-induced dimensional changes (axial and radial shrinkage) is subsequently applied. The authors compare weight loss forecasts made using FEAT DIFFUSE with those based on an alternative statistical model for a layer four moderator brick for the Hinkley Point B, Reactor 3. The authors compare the two approaches for the weight loss distribution through the brick with a particular focus on the interstitial keyway, and for the average (over the volume of the brick) weight loss.

  1. LEGO bricks used as chemotactic chambers: evaluation by a computer-assisted image analysis technique.

    Science.gov (United States)

    Azzarà, A; Chimenti, M

    2004-01-01

    One of the main techniques used to explore neutrophil motility, employs micropore filters in chemotactic chambers. Many new models have been proposed, in order to perform multiple microassays in a rapid, inexpensive and reproducible way. In this work, LEGO bricks have been used as chemotactic chambers in the evaluation of neutrophil random motility and chemotaxis and compared with conventional Boyden chambers in a "time-response" experiment. Neutrophil motility throughout the filters was evaluated by means of an image-processing workstation, in which a dedicated algorithm recognizes and counts the cells in several fields and focal planes throughout the whole filter; correlates counts and depth values; performs a statistical analysis of data; calculates the true value of neutrophil migration; determines the distribution of cells; and displays the migration pattern. By this method, we found that the distances travelled by the cells in conventional chambers and in LEGO bricks were perfectly identical, both in random migration and under chemotactic conditions. Moreover, no interference with the physiological behaviour of neutrophils was detectable. In fact, the kinetics of migration was identical both in random migration (characterized by a gaussian pattern) and in chemotaxis (characterized by a typical stimulation peak, previously identified by our workstation). In conclusion, LEGO bricks are extremely precise devices. They are simple to use and allow the use of small amounts of chemoattractant solution and cell suspension, supplying by itself a triplicate test. LEGO bricks are inexpensive, fast and suitable for current diagnostic activity or for research investigations in every laboratory.

  2. A Comprehensive Study on Gamma-Ray Exposure Build-Up Factors and Fast Neutron Removal Cross Sections of Fly-Ash Bricks

    OpenAIRE

    2013-01-01

    Geometric progression (GP) method was utilized to investigate gamma-ray exposure build-up factors of fly-ash bricks for energies from 0.015 to 15 MeV up to 40 mfp penetration depth. The EBFs of the fly-ash bricks are dependent upon the photon energy, penetration depths, and the chemical compositions of the elements. Appreciable variations in exposure build-up factor (EBF) are noted for the fly-ash bricks. The EBFs were found to be small in low and high photon energy regions whereas very large...

  3. Neutrosophic Decision Making Model for Clay-Brick Selection in Construction Field Based on Grey Relational Analysis

    Directory of Open Access Journals (Sweden)

    Kalyan Mondal

    2015-09-01

    Full Text Available The purpose of this paper is to present quality clay-brick selection approach based on multi-attribute decision making with single valued neutrosophic grey relational analysis. Brick plays a significant role in construction field. So it is important to select quality clay-brick for construction based on suitable mathematical decision making tool. There are several selection methods in the literature. Among them decision making with neutrosophic set is very pragmatic and interesting. Neutrosophic set is one tool that can deal with indeterminacy and inconsistent data. In the proposed method, the rating of all alternatives is expressed with single-valued neutrosophic set which is characterized by truth-membership degree (acceptance, indeterminacy membership degree and falsity membership degree (rejection. Weight of each attribute is determined based on experts’ opinions. Neutrosophic grey relational coefficient is used based on Hamming distance between each alternative to ideal neutrosophic estimates reliability solution and ideal neutrosophic estimates unreliability solution. Then neutrosophic relational degree is used to determine the ranking order of all alternatives (bricks. An illustrative numerical example for quality brick selection is solved to show the effectiveness of the proposed method.

  4. Moisture transport properties of brick – comparison of exposed, impregnated and rendered brick

    DEFF Research Database (Denmark)

    Hansen, Tessa Kvist; Bjarløv, Søren Peter; Peuhkuri, Ruut

    2016-01-01

    In regards to internal insulation of preservation worthy brick façades, external moisture sources, such as wind-driven rain exposure, inevitably has an impact on moisture conditions within the masonry construction. Surface treatments, such as hydrophobation or render, may remedy the impacts...

  5. Asphalt, Fleets, Bricks, and Mortar.

    Science.gov (United States)

    Green, Tim; Williamson, Margie E.; Endris, William L., Jr.

    2000-01-01

    The new reporting model propounded in Governmental Accounting Board Statement No. 34 dictates that consumption of capital assets be reported through a charge in the governmentwide statement of activities for depreciation expense. The present method of "rolling forward" capital asset amounts will not suffice. (MLH)

  6. Development of High Quality Magnesite—Chrome Bricks for Secondary Steelmaking Furnaces

    Institute of Scientific and Technical Information of China (English)

    LIYong; LIUShensheng; 等

    1998-01-01

    This paper describes developments of high quality magnesite-chrome bricks used for secondary steelmaking furnaces,mainly including direct-bond-ed magnesite-chrome brick,fully synthesized(co-clinker) magnesite-chrome brick,semi-rebonded magnesite-chrome brick and fused grain rebonded magnesite-chroe brick,Investigations have also been conducted on the effects of various chromites on the properties of the direct bonded magnesite-chrome brick,effects of different sesquioxides (CrO3,Al3O3,Fe2O3) on the properties of the fully synthe-sized(co-clinker) magnesite-hrome brick and ef-fects of ZrO2,Cr-Fe alloy,ultra-fine powders on the properties of the fused grain rebonded brick and the semi-rebonded magnesite-chrome brick ,Applica-tions of the bricks in various secondary steelmaking furnaces have been briefly introduced as well.

  7. Inside the Sex Ed Studio: An Interview with Peggy Brick

    Science.gov (United States)

    Taverner, William J.

    2008-01-01

    "Inside the Sex Ed Studio" profiles leaders in the field of sexuality education. Peggy Brick, former director of Planned Parenthood of Greater Northern New Jersey's Center for Family Life Education (CFLE) and author of numerous sexuality education resources used worldwide, is the subject of this interview. Ms. Brick was interviewed by…

  8. An Exploration of the Nanoworld with LEGO Bricks

    Science.gov (United States)

    Campbell, Dean J.; Miller, Josiah D.; Bannon, Stephen J.; Obermaier, Lauren M.

    2011-01-01

    LEGO bricks can be used for a number of demonstrations of chemical structures and properties, especially at the nanoscale level. These bricks can also be used to model instrumentation that probes these structures and properties. Detailed resources about many of these demonstrations are located on the extensive Web site "Exploring the Nanoworld…

  9. 78 FR 3449 - Silica Bricks and Shapes From China

    Science.gov (United States)

    2013-01-16

    ... 23, 2012 (77 FR 70185). The conference was held in Washington, DC, on December 6, 2012, and all... COMMISSION Silica Bricks and Shapes From China Determination On the basis of the record \\1\\ developed in the... China of silica bricks and shapes, provided for in subheading 6902.20.10 of the Harmonized...

  10. Utilization of Household Sewage Sludge in Brick making

    Institute of Scientific and Technical Information of China (English)

    SunGuofeng

    2005-01-01

    Household sewage sludge is a kind of solid waste produced in sewage purifying at sewage farm. in procedure of water purifying, which can be used as raw material for producing fired brick. This article compares the chemical composition between household sewage sludge and clay, and explores two kinds of production process for making brick with Household sewage sludge.

  11. Possible weathering of the brick matrix when exposed to water

    DEFF Research Database (Denmark)

    Rörig-Dalgaard, Inge

    2014-01-01

    The main reasons for deterioration of bricks are frost, crystallization pressure and chemical exposure. Despite of this the effect of chemical exposure is limited clarified. Depending on the brick type the original pH of bricks are 9-10. Though bricks can to subjected to water in shape of acid rain...... with a pH as low as 3. The exposure of acid rain and rain water to bricks is expected to have an influence on the brick matrix dependent on the specific exposure but to which extend? The present work is a systematic test of the influence of the pH on the brick matrix where the effect of water...... with different well-defined pH values are examined to investigate the long term effect of acid rain or other reasons causing pH changes to bricks (as e.g. electrokinetic treatment). Through capillary suction, macro pictures from the exposed surfaces, measurement of the pH and electrical conductivity it seemed...

  12. Physico-mechanical characterization of adobe bricks from Cyprus

    Science.gov (United States)

    Ioannou, I.; Illampas, R.; Charmpis, D. C.

    2012-04-01

    set. Furthermore, distinct differences are noted among the properties of: (a) adobes produced by different manufactures; (b) adobes made by the same manufacturer but originating from different production batches and (c) specimens originating from the same brick. The flexural strength of adobes is also quite variable and the mode of failure under bending is influenced by the presence of discontinuities within the mass of the material. As a result, a very weak correlation between the flexural and compressive strength of the test specimens is noted. This abnormal mechanical behaviour is attributed to the inherent inhomogeneity and natural randomness of adobes which is "enhanced" by the adoption of empirical non-industrialized production methods. Discrepancy in the outcomes of laboratory tests is further affected by the lack of standardized testing methods and formal failure criteria.

  13. Electrochemical desalination of bricks - Experimental and modeling

    DEFF Research Database (Denmark)

    Skibsted, Gry; Ottosen, Lisbeth M.; Jensen, Pernille Erland

    2015-01-01

    Chlorides, nitrates and sulfates play an important role in the salt-decay of porous materials in buildings and monuments. Electrochemical desalination is a technology able to remove salts from such porous materials in order to stop or prevent the decay. In this paper, experimental and numerical......-contaminated bricks with respect to the monovalent ions is discussed. Comparison between the experimental and the simulation results showed that the proposed numerical model is able to predict electrochemical desalination treatments with remarkable accuracy, and it can be used as a predictive tool...

  14. Assessment of natural radioactivity and mass attenuation coefficients of brick and roofing tile used in Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Damla, N., E-mail: nevzat.damla@batman.edu.tr [Batman University, Department of Physics, 72060 Batman (Turkey); Cevik, U.; Kobya, A.I. [Karadeniz Technical University, Department of Physics, 61080 Trabzon (Turkey); Celik, A. [Giresun University, Department of Physics, 28049 Giresun (Turkey); Celik, N. [Guemueshane University, Department of Physics Engineering, 29100 Guemueshane Turkey (Turkey); Yildirim, I. [Karadeniz Technical University, Department of Forest Industry, 61080 Tranzon (Turkey)

    2011-08-15

    In this study the distribution of natural radionuclides ({sup 226}Ra, {sup 232}Th, {sup 40}K) in brick and roofing tile samples commonly used as building materials in Turkey was measured by using gamma spectrometry. The activity concentrations, radium equivalent activities (Ra{sub eq}), representative level index, indoor absorbed dose rate in air values and annual effective dose due to the intake of the above-mentioned radionuclides in the brick and roofing tile samples were estimated to assess the radiation hazard for people living in dwellings made of the materials studied. The measured average activity concentrations of {sup 226}Ra, {sup 232}Th and {sup 40}K were 34 {+-} 14, 34 {+-} 13 and 462 {+-} 175 Bq.kg{sup -1}, respectively, for brick samples. For roofing tile, the average activity concentrations of {sup 226}Ra, {sup 232}Th and {sup 40}K were measured to be 34 {+-} 14, 33 {+-} 12 and 429 {+-} 161 Bq.kg{sup -1}, respectively. The concentrations for these natural radionuclides were compared with the reported data of other countries. The Ra{sub eq} values of all samples were lower than the limit of 370 Bq.kg{sup -1}, equivalent to a gamma dose of 1.5 mSv.a{sup -1} recommended by OECD. This study shows that the measured brick and roofing tile samples do not pose any significant source of radiation hazard and are safe to be used as building materials. Moreover, the experimental mass attenuation coefficients ({mu}/{rho}) of brick and roofing tile samples were determined in the energy range 80-1332 keV using the gamma ray transmission method. The experimental mass attenuation coefficients were compared with theoretical values obtained using XCOM. It was found that the computed values and the experimental results of this work are in good agreement with those reported in the literature. The chemical compositions and structural analysis (XRD) of the brick and roofing tile samples are also presented. - Highlights: > In this study, the distribution of natural

  15. Wall modeling via function enrichment within a high-order DG method for RANS simulations of incompressible flow

    CERN Document Server

    Krank, Benjamin; Wall, Wolfgang A

    2016-01-01

    We present a novel approach to wall modeling for RANS within the discontinuous Galerkin method. Wall functions are not used to prescribe boundary conditions as usual but they are built into the function space of the numerical method as a local enrichment, in addition to the standard polynomial component. The Galerkin method then automatically finds the optimal solution among all shape functions available. This idea is fully consistent and gives the wall model vast flexibility in separated boundary layers or high adverse pressure gradients. The wall model is implemented in a high-order discontinuous Galerkin solver for incompressible flow complemented by the Spalart-Allmaras closure model. As benchmark examples we present turbulent channel flow starting from $Re_{\\tau}=180$ and up to $Re_{\\tau}=100{,}000$ as well as flow past periodic hills at Reynolds numbers based on the hill height of $Re_H=10{,}595$ and $Re_{H}=19{,}000$.

  16. Research of the biochemistry compositions of three kinds of brick tea%三种砖茶品质生化成分的研究

    Institute of Scientific and Technical Information of China (English)

    赖幸菲; 柏珍; 李智芳; 黄亚辉

    2012-01-01

    通过比较三种砖茶中各种生化成分含量的差异,分析了不同加工工艺对砖茶生化成分以及成茶品质风味的影响。实验结果表明,黑砖茶的水浸出物、茶多酚、咖啡碱、游离氨基酸及三种色素的含量均为最高,茯砖茶次之,青砖茶最低,而可溶性糖的含量是黑砖茶最低,青砖茶最高。三种砖茶生化成分的差异主要是由不同的加工工艺造成的,茯砖茶有独特的"发花"工序,其品质表现为有菌花香,滋味醇和;黑砖茶的原料较嫩,加工过程比较简单,内含成分高,滋味表现为纯厚微涩;青砖茶的原料最为粗老,自然发酵时间长,可溶性糖含量高,其品质表现为香气纯正,滋味甘甜。%The main biochemistry compositions of Fuzhuan brick tea, Black brick tea and Green brick tea and the influences with different processed methods were studied.The experiment results showed that the contents of water extract, tea polyphenol, caffeine, free amino acid, theaflavins ( TFs ), thearubigins (TRs) and theabrownines (TBs) in Black brick tea were the highest, which in Fuzhuan brick tea were the second, and in Green brick tea was the lowest.The content of soluble sugar in Black brick tea was the lowest,while in Green brick tea was the highest.With different processed methods ,the contents of biochemistry compositions of the three brick teas were changed, and different quality characters were showed.Fuzhuan brick tea had a unique process--fungus growing,this endowed it with arohid flavour and mellow taste. Black brick tea was made by tender fresh leaves and had more compositions.Thus it tasted pure, rich and subastringent.Green brick tea was made by the oldest fresh leaves.It incited sweet and had pure aroma, this was due to its rich soluble sugar and the long natural fermentation processes.

  17. Organic/hybrid nanoparticles and single-walled carbon nanotubes: preparation methods and chiral applications.

    Science.gov (United States)

    Alhassen, Haysem; Antony, Vijy; Ghanem, Ashraf; Yajadda, Mir Massoud Aghili; Han, Zhao Jun; Ostrikov, Kostya Ken

    2014-11-01

    Nanoparticles are molecular-sized solids with at least one dimension measuring between 1-100 nm or 10-1000 nm depending on the individual discipline's perspective. They are aggregates of anywhere from a few hundreds to tens of thousands of atoms which render them larger than molecules but smaller than bulk solids. Consequently, they frequently exhibit physical and chemical properties somewhere between. On the other hand, nanocrystals are a special class of nanoparticles which have started gaining attention recently owing to their unique crystalline structures which provide a larger surface area and promising applications including chiral separations. Hybrid nanoparticles are supported by the growing interest of chemists, physicists, and biologists, who are researching to fully exploit them. These materials can be defined as molecular or nano-composites with mixed (organic or bio) and inorganic components, where at least one of the component domain has a dimension ranging from a few Å to several nanometers. Similarly, and due to their extraordinary physical, chemical, and electrical properties, single-walled carbon nanotubes have been the subject of intense research. In this short review, the focus is mainly on the current well-established simple preparation techniques of chiral organic and hybrid nanoparticles as well as single-walled carbon nanotubes and their applications in separation science. Of particular interest, cinchonidine, chitosan, and β-CD-modified gold nanoparticles (GNPs) are discussed as model examples for organic and hybrid nanoparticles. Likewise, the chemical vapor deposition method, used in the preparation of single-walled carbon nanotubes, is discussed. The enantioseparation applications of these model nanomaterials is also presented.

  18. Occupational Health Hazards of Women Working in Brick Kiln and Construction Industry

    Directory of Open Access Journals (Sweden)

    V. G Vaidya

    2015-01-01

    Full Text Available Background: In brick kiln and construction industry the exposure to carbon monoxide and silica dust is the most common occupational hazard to the workers in these industries. A study on occupational health hazards of working women in these two unorganized sectors was undertaken by Lokmanya Medical Research Centre. Objectives: To study the effect of work site environment on the health of the women working in brick kiln and construction industry. An attempt was also made to study the seasonal changes in the concentration of carbon monoxide and dust at the worksite. Material and Methods: A cross-sectional study was conducted among the working women (age 18-40 years at brick kilns and construction sites during summer and winter season. They were examined primarily to assess the effect of working environment on health. Gasteck Detector Pump of model 800 and air sampling instrument (SKC Air Check–52 were used to measure concentration of carbon monoxide and dust in the air respectively. Results: There were 66% of women who were in the age group of 18-40 years and most of them (94% were married. At brick kiln sites, average CO exposure was 62.8 ppm and 55.5 ppm and average dust exposure was 3 3 146.1 mg/m and 91.4 mg/m in summer and winter season respectively.At construction sites, average dust exposure was 41.5 ppm and 90.8 ppm in summer and winter. Conclusion: Both exposure to CO and dust were more in summer than in winter in brick kiln industry whereas in construction industry the exposure to dust was more in winter season. A high level of morbidity in the form of headache, bodyache, problems with vision, cough and breathlessness were observed in both industries. It is strongly recommended to take pollution control measures.

  19. LEVEL SET METHOD FOR NUMERICAL SIMULATION OF A CAVITATION BUBBLE COLLAPSING NEAR A RIGID WALL

    Institute of Scientific and Technical Information of China (English)

    HUANG Jun-tao; ZHANG Hui-sheng

    2005-01-01

    The level set method, TVD scheme of second order upwind procedure coupled with flux limiter, ENO velocity extension procedure inside the bubble, and MAC projection algorithm were incorporated to simulate the whole collapse evolution of a cavitation bubble near a rigid wall with many complicated phenomena, such as topology distortion and shrinking, jet impact, bubble breaking into a toroidal form, and diminishing volume to zero, etc.The bubble shape, evolution and distribution of velocity and pressure fields of the fluid during the bubble collapsing were investigated.It is found that the method is numerically stable and has good convergence property, and the results are in good agreements with those in previous work.

  20. A Comprehensive Review on Separation Methods and Techniques for Single-Walled Carbon Nanotubes

    Directory of Open Access Journals (Sweden)

    Naoki Komatsu

    2010-06-01

    Full Text Available Structural control of single-walled carbon nanotubes (SWNTs is attracting enormous interest in view of their applications to nanoelectronics and nanooptics. Actually, more than 200 papers regarding separation of SWNTs have been published since 1998. In this review, they are classified into the following five sections according to the separation methods; electrophoresis, centrifugation, chromatography, selective solubilization and selective reaction. In each method, all literature is summarized in tables showing the separated objects (metallic/semiconducting (M/S, length, diameter, (n, m structure and/or handedness, the production process of the used SWNTs (CoMoCAT, HiPco, arc discharge and/or laser vaporization and the employed chemicals, such as detergents and polymers. Changes in annual number of publications related to this subject are also discussed.

  1. A nondestructive method for diagnostic of insulated building walls using infrared thermography

    Science.gov (United States)

    Larbi Youcef, Mohamed H. A.; Mazioud, Atef; Bremond, Pierre; Ibos, Laurent; Candau, Yves; Piro, Michel; Filloux, Alain

    2007-04-01

    This work deals with the development of an experimental protocol for the diagnostic of multi-layered insulated building walls. First, a test bench is set up in order to measure front and back sides temperatures of standard panels. The panels considered have insulation thicknesses of 2, 6 and 10cm. The front side is heated by two halogen lamps of 500W. A CEDIP Jade Long wave infrared camera and thermocouples are used to carry out temperature measurements. In a second time, a one dimensional model based on thermal quadruples and Laplace transforms was developped under Matlab environment. Also, we developped a three dimensional model based on finite volumes using Fluent computational code. Finally, a method of identification of physical parameters is implemented by performing least square minimization based on Levenberg-Marquardt method. The experimental measurements are compared to theoretical results and by minimization we obtain thermal conductivity and diffusivity as well as thickness of the two layers.

  2. Comparative Study of Two Daylighting Analysis Methods with Regard to Window Orientation and Interior Wall Reflectance

    Directory of Open Access Journals (Sweden)

    Yeo Beom Yoon

    2014-09-01

    Full Text Available The accuracy and speed of the daylighting analysis developed for use in EnergyPlus is better than its predecessors. In EnergyPlus, the detailed method uses the Split-flux algorithm whereas the DElight method uses the Radiosity algorithm. Many existing studies have addressed the two methods, either individually or compared with other daylight analysis methods like Ray tracing but still there is lack of detailed comparative study of these two methods. Our previous studies show that the Split-flux method overestimates the illuminance, especially for the areas away from the window. The Radiosity method has the advantage of accurately predicting this illuminance because of how it deals with the diffuse light. For this study, the EnergyPlus model, which has been calibrated using data measured in a real building in previous studies, has also been used. The calibrated model has a south oriented window only. This model is then used to analyze the interior illuminance inside the room for north, west and east orientation of the window by rotating the model and by changing the wall reflectance of the model with south oriented window. Direct and diffuse component of the illuminance as well as the algorithms have been compared for a detailed analysis.

  3. Modelling of single walled carbon nanotube cylindrical structures with finite element method simulations

    Science.gov (United States)

    Günay, E.

    2016-04-01

    In this study, the modulus of elasticity and shear modulus values of single-walled carbon nanotubes SWCNTs were modelled by using both finite element method and the Matlab code. Initially, cylindrical armchair and zigzag single walled 3D space frames were demonstrated as carbon nanostructures. Thereafter, macro programs were written by the Matlab code producing the space truss for zigzag and armchair models. 3D space frames were introduced to the ANSYS software and then tension, compression and additionally torsion tests were performed on zigzag and armchair carbon nanotubes with BEAM4 element in obtaining the exact values of elastic and shear modulus values. In this study, two different boundary conditions were tested and especially used in torsion loading. The equivalent shear modulus data was found by averaging the corresponding values obtained from ten different nodal points on the nanotube path. Finally, in this study it was determined that the elastic constant values showed proportional changes by increasing the carbon nanotube diameters up to a certain level but beyond this level these values remained stable.

  4. Thermal diffusivity of aligned multi-walled carbon nanotubes measured by the flash method

    Energy Technology Data Exchange (ETDEWEB)

    Maeklin, Jani; Halonen, Niina; Toth, Geza; Jantunen, Heli [Microelectronics and Materials Physics Laboratories, University of Oulu (Finland); Sapi, Andras; Kukovecz, Akos; Konya, Zoltan [Department of Applied and Environmental Chemistry, University of Szeged (Hungary); Mikkola, Jyri-Pekka [Department of Chemistry, Technical Chemistry, Umeaa University (Sweden); Kordas, Krisztian [Microelectronics and Materials Physics Laboratories, University of Oulu (Finland); Department of Chemistry, Technical Chemistry, Umeaa University (Sweden)

    2011-11-15

    Thermal diffusivity of freestanding catalytic chemical vapor deposition (CCVD) grown multi-walled carbon nanotube (MWCNT) forests (height of 1.5 and 1.9 mm) was characterized in the temperature range between 25 and 200 C. Copper and Al-alloy metal blocks were used as references for validation of the experimental setup. The measurements were carried out along the MWCNT alignment direction with a thermal property analyzer that uses the flash method. The thermal diffusivities measured at room temperature for as-grown and post-annealed (2 h at 480 C in open air) samples were found to be {proportional_to}0.45 and {proportional_to}0.23 cm{sup 2}/s, respectively. In both cases, the thermal diffusivity values were slightly decreasing with increasing temperature. The observed decrease in diffusivity after annealing is most probably due to the loss of amorphous carbon in the specimens and also because of the increased defect density in the nanotube walls resulting in a more pronounced phonon scattering in the lattice. The measured thermal diffusivities for as-grown samples agree with data reported elsewhere for similar MWCNT materials [W. Yi et al., Rev. B 59, 9015 (1999) and T. Borca-Tasciuc et al., J. Appl. Phys. 98, 054309 (2005)]. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  5. Volatile Retention and Morphological Properties of Microencapsulated Tributyrin Varied by Wall Material and Drying Method.

    Science.gov (United States)

    Donovan, Joseph D; Cadwallader, Keith R; Lee, Youngsoo

    2016-03-01

    Butyric acid is an important short-chain fatty acid for intestinal health and has been shown to improve certain intestinal disease states. A triglyceride containing 3 butyric acid esters, tributyrin (TB) can serve as a source of butyric acid; however, the need to target intestinal delivery and mitigate unpleasant sensory qualities has limited its use in food. Microencapsulation, the entrapment of one or more cores within a matrix, may provide a solution to the aforementioned challenge. This research primarily focused on the influence of (1) wall material: whey and soy protein isolate (WPI and SPI, respectively) and gamma-cyclodextrin (GCD), (2) wall additives: inulin of varying chain length, and (3) processing method: spray or oven drying (SD or OD, respectively) on the morphological properties and volatile retention of TB within microcapsules. SPI-based microcapsules retained significantly less (P spray dried, the GCD-based microcapsules exhibited (P spray drying. These findings demonstrate that microencapsulated TB in GCD can lead to minimal TB losses during processing that could be utilized in functional food applications for intestinal health.

  6. Papercrete Bricks - An Alternative Sustainable Building Material

    Directory of Open Access Journals (Sweden)

    Myriam Marie Delcasse

    2017-03-01

    Full Text Available A large amount of non-renewable resources is consumed by the construction industry throughout the world. Everyday tons of waste papers are discarded as landfill or dump sites than those recycled. It is learnt that it takes about fifteen trees to make a ton of paper which means that 720 million trees are used once and then buried as landfills each year. In order to address these issues it has become imperative to push the boundaries of research in the field of innovative sustainable construction materials. This study is one such kind of efforts. Papercrete is a new composite material comprising of waste papers and cement. In this investigation, an attempt is made to produce an alternative material using waste papers. This could help eradicate a few of the environmental hazards caused by the construction industry. But there is no proper code for the mix proportioning of papercrete bricks. Therefore, a mix proportion of [Cement: Paper: Sand] 1:1.15:1.3 was chosen on trial and error basis. All the necessary engineering properties are studied and compared with the conventional bricks and discussions on its potential uses are made.

  7. A straightforward method for wall impedance eduction in a flow duct.

    Science.gov (United States)

    Jing, Xiaodong; Peng, Sen; Sun, Xiaofeng

    2008-07-01

    The development of the advanced liner technology for aeroengine noise control necessitates the impedance measurement method under realistic flow conditions. Currently, the methods for this need are mainly based on the inverse impedance eduction principle, confronting with the problems of initial guess, high computation cost, and low convergence. In view of this, a new strategy is developed that straightforwardly educes the impedance from the sound pressure information measured on the duct wall opposing to the test acoustic liner embedded in a flow duct. Here, the key insight is that the modal nature of the duct acoustic field renders a summed-exponential representation of the measured sound pressure; thus, the characterizing axial wave number can be readily extracted by means of Prony's method, and further the unknown impedance is calculated from the eigenvalue and dispersion relations based on the classical mode-decomposition analysis. This straightforward method is simple in its basic principle but remarkably has the advantages of ultimately overcoming the drawbacks inherent to the inverse methods, incorporating the realistic multimode nonprogressive wave effects, high computational efficiency, possibly reducing the measurement points, and even avoiding the necessity of the duct exit impedance that bothers perhaps all the existing waveguide methods.

  8. Spatial variability in the coefficient of thermal expansion induces pre-service stresses in computer models of virgin Gilsocarbon bricks

    Science.gov (United States)

    Arregui-Mena, José David; Margetts, Lee; Griffiths, D. V.; Lever, Louise; Hall, Graham; Mummery, Paul M.

    2015-10-01

    In this paper, the authors test the hypothesis that tiny spatial variations in material properties may lead to significant pre-service stresses in virgin graphite bricks. To do this, they have customised ParaFEM, an open source parallel finite element package, adding support for stochastic thermo-mechanical analysis using the Monte Carlo Simulation method. For an Advanced Gas-cooled Reactor brick, three heating cases have been examined: a uniform temperature change; a uniform temperature gradient applied through the thickness of the brick and a simulated temperature profile from an operating reactor. Results are compared for mean and stochastic properties. These show that, for the proof-of-concept analyses carried out, the pre-service von Mises stress is around twenty times higher when spatial variability of material properties is introduced. The paper demonstrates that thermal gradients coupled with material incompatibilities may be important in the generation of stress in nuclear graphite reactor bricks. Tiny spatial variations in coefficient of thermal expansion (CTE) and Young's modulus can lead to the presence of thermal stresses in bricks that are free to expand.

  9. 75 FR 4528 - Certain Magnesia Carbon Bricks From the People's Republic of China: Alignment of Final...

    Science.gov (United States)

    2010-01-28

    ... International Trade Administration Certain Magnesia Carbon Bricks From the People's Republic of China: Alignment... Carbon Bricks (Bricks) from the People's Republic of China (PRC) with the final determinations of the antidumping duty (AD) investigations of Bricks from the PRC and Mexico. DATES: Effective Date: January...

  10. Characterization, reproduction and optimization of traditional adobe bricks

    Science.gov (United States)

    Ioannou, Ioannis; Eftychiou, Marina; Costi de Castrillo, Maria; Illampas, Rogiros

    2013-04-01

    ratio 1:1 produce results ranging from 1-2 MPa, whereas prisms with height-to-width ratios adobes produced by different manufactures; (b) adobes made by the same manufacturer but originating from different production batches and (c) specimens originating from the same brick. When subjected to three-point bending, the behaviour of adobes is influenced by the presence of discontinuities within their mass. Hence, flexural strength is rather variable and weakly correlated to compressive strength. This abnormal mechanical behaviour is attributed to the inherent inhomogeneity and natural randomness of adobes which is "enhanced" by the adoption of empirical non-industrialized production methods. Discrepancy in the outcomes of laboratory tests is further affected by the lack of standardized testing methods and formal failure criteria. Laboratory designed and produced adobes show improved mechanical properties and lower thermal conductivities. The addition of wood dust in the mixture, at quantities up to 60% by volume, seems particularly beneficial, as it raises the compressive strength of the material over 6 MPa, while at the same time it reduces its capillary water absorption coefficient to about 0.35 mm/min1 -2. The latter is further reduced by the use of commercially available water repellents in the mixture. Wood dust also reduces the thermal conductivity of adobes. Among the stabilizing additives used, gypsum proved to be the most beneficial. In general, simple modifications to the procedure followed during the laboratory production of adobes, such as in the filling of moulds, lead to higher density and compressive strength of the end-product.

  11. Measurement of Specific Heat Capacity of Insulating Brick at High Temperatures by a Half-Open Dynamic Method Based on Hybrid Principle%采用基于混合原理的动态半开放方法测量保温砖的高温比热容

    Institute of Scientific and Technical Information of China (English)

    龙海敏; 卢元; 康进武; 聂刚; 马斌; 付龙

    2011-01-01

    保温砖是铸造中的常用材料,比热容是材料重要的热物性参数,也是铸件凝固过程数值模拟所需参数.保温砖为多孔材料,其高温比热容测量困难.针对这种情况,提出了基于混合原理的动态半开放比热容测量方法,并研制了相应的比热容测量仪.采用已知比热容的蓝宝石试样进行标定,试验值和理论值误差在6.3%以内.采用此方法测得了进口和国产两种保温砖在30~760℃的比热容曲线.%Insulating brick is widely used in casting production. Its specific heat capacity is one of the important thermal properties and crucial for numerical simulation of solidification process. Because of its porous characteristic, it is hard to measure the specific heat capacity at high temperatures. In this paper, a half-open dynamic measurement method based on hybrid principle was presented and a measurement device was established. Sapphire with given standard value of specific heat capacity is used to calibrate the system; the error is less than 6.3%. Specific heat capacity of two different kinds of insulating bricks were measured in the temperature range from 30 °C to760°Co

  12. Coupling of a 3-D vortex particle-mesh method with a finite volume near-wall solver

    Science.gov (United States)

    Marichal, Y.; Lonfils, T.; Duponcheel, M.; Chatelain, P.; Winckelmans, G.

    2011-11-01

    This coupling aims at improving the computational efficiency of high Reynolds number bluff body flow simulations by using two complementary methods and exploiting their respective advantages in distinct parts of the domain. Vortex particle methods are particularly well suited for free vortical flows such as wakes or jets (the computational domain -with non zero vorticity- is then compact and dispersion errors are negligible). Finite volume methods, however, can handle boundary layers much more easily due to anisotropic mesh refinement. In the present approach, the vortex method is used in the whole domain (overlapping domain technique) but its solution is highly underresolved in the vicinity of the wall. It thus has to be corrected by the near-wall finite volume solution at each time step. Conversely, the vortex method provides the outer boundary conditions for the near-wall solver. A parallel multi-resolution vortex particle-mesh approach is used here along with an Immersed Boundary method in order to take the walls into account. The near-wall flow is solved by OpenFOAM® using the PISO algorithm. We validate the methodology on the flow past a sphere at a moderate Reynolds number. F.R.S. - FNRS Research Fellow.

  13. Nonlinear free vibrations of curved double walled carbon nanotubes using differential quadrature method

    Science.gov (United States)

    Cigeroglu, Ender; Samandari, Hamed

    2014-11-01

    Nonlinear free vibration analysis of curved double-walled carbon nanotubes (DWNTs) embedded in an elastic medium is studied in this study. Nonlinearities considered are due to large deflection of carbon nanotubes (geometric nonlinearity) and nonlinear interlayer van der Waals forces between inner and outer tubes. The differential quadrature method (DQM) is utilized to discretize the partial differential equations of motion in spatial domain, which resulted in a nonlinear set of algebraic equations of motion. The effect of nonlinearities, different end conditions, initial curvature, and stiffness of the surrounding elastic medium, and vibrational modes on the nonlinear free vibration of DWCNTs is studied. Results show that it is possible to detect different vibration modes occurring at a single vibration frequency when CNTs vibrate in the out-of-phase vibration mode. Moreover, it is observed that boundary conditions have significant effect on the nonlinear natural frequencies of the DWCNT including multiple solutions.

  14. Laboratory evaluation of cement treated aggregate containing crushed clay brick

    Directory of Open Access Journals (Sweden)

    Liqun Hu

    2014-10-01

    Full Text Available The waste clay bricks from debris of buildings were evaluated through lab tests as environmental friendly materials for pavement sub-base in the research. Five sets of coarse aggregates which contained 0, 25%, 50%, 75% and 100% crushed bricks, respectively, were blended with sand and treated by 5% cement. The test results indicated that cement treated aggregate which contains crushed clay brick aggregate had a lower maximum dry density (MDD and a higher optimum moisture content (OMC. Moreover, the unconfined compressive strength (UCS, resilience modulus, splitting strength, and frost resistance performance of the specimens decreased with increase of the amount of crushed clay brick aggregate. On the other hand, it can be observed that the use of crushed clay brick in the mixture decreased the dry shrinkage strain of the specimens. Compared with the asphalt pavement design specifications of China, the results imply that the substitution rate of natural aggregate with crushed clay brick aggregate in the cement treated aggregate sub-base material should be less than 50% (5% cement content in the mixture. Furthermore, it needs to be noted that the cement treated aggregate which contains crushed clay bricks should be cautiously used in the cold region due to its insufficient frost resistance performance.

  15. Thermal Performance of the Storage Brick Containing Microencapsulated PCM

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong Gyu

    1998-02-15

    The utilization of microencapsulated phase change materials(PCMs) provides several advantages over conventional PCM application. The heat storage system, as well as heat recovery system, can be built to a smaller size than the normal systems for a given thermal cycling capacity. This microencapsulated PCM technique has not yet been commercialized, however. In this work sodium acetate trihydrate(CH{sub 3}COONa {center_dot} 3H{sub 2}O) was selected for the PCM and was encapsulated. This microencapsulated PCM was mixed with cement mortar for utilization as a floor heating system. In this experiment performed here the main purpose was to investigate the thermal performance of a storage brick with microencapsulated PCM concentration. The thermal performance of this storage brick is dependent on PCM concentration, flow rate and cooling temperature of the heat transfer fluid, etc. The results showed that cycle time was shortened as the PCM content was increased and as the mass flow rate was increased. The same effect was obtained when the cooling temperature was decreased. For each thermal storage brick the overall heat transfer coefficient(U-value) was constant for a 0% brick, but was increased with time for the bricks containing microencapsulated PCM. For the same mass flow rate, as the cooling temperature decreased, the amount of heat withdrawn increased, and in particular a critical cooling temperature was found for each thermal storage brick. The average effectiveness of each thermal storage brick was found to be approximately 48%, 51% and 58% respectively.

  16. Study on Properties of Magnesia-Hercynite Brick

    Institute of Scientific and Technical Information of China (English)

    LIU Huilin; LI Ning; LI Qiang

    2005-01-01

    Using magnesia and hercynite as materials, we researched the magnesia-hercynite brick in order to solve the problem of chrome-free brick used in the burning zone of cement rotary kiln. Effect of different firing temperature and different content of hercynite on properties of the brick were studied. The results show that the magnesia-hercynite specimen fired at 1600℃ was densified and when the hercynite content is 7%, the cold crushing strength and the adhesive strength of rupture of the specimen have the highest value.

  17. Improved dispersion method of multi-wall carbon nanotube for inhalation toxicity studies of experimental animals.

    Science.gov (United States)

    Taquahashi, Yuhji; Ogawa, Yukio; Takagi, Atsuya; Tsuji, Masaki; Morita, Koichi; Kanno, Jun

    2013-01-01

    A multi-wall carbon nanotube (MWCNT) product Mitsui MWNT-7 is a mixture of dispersed single fibers and their agglomerates/aggregates. In rodents, installation of such mixture induces inflammatory lesions triggered predominantly by the aggregates/agglomerates at the level of terminal bronchiole of the lungs. In human, however, pulmonary toxicity induced by dispersed single fibers that reached the lung alveoli is most important to assess. Therefore, a method to generate aerosol predominantly consisting of dispersed single fibers without changing their length and width is needed for inhalation studies. Here, we report a method (designated as Taquann method) to effectively remove the aggregate/agglomerates and enrich the well-dispersed singler fibers in dry state without dispersant and without changing the length and width distribution of the single fibers. This method is base on two major concept; liquid-phase fine filtration and critical point drying to avoid re-aggregation by surface tension. MWNT-7 was suspended in Tert-butyl alcohol, freeze-and-thawed, filtered by a vibrating 25 µm mesh Metallic Sieve, snap-frozen by liquid nitrogen, and vacuum-sublimated (an alternative method to carbon dioxide critical point drying). A newly designed direct injection system generated well-dispersed aerosol in an inhalation chamber. The lung of mice exposed to the aerosol contained single fibers with a length distribution similar to the original and the Taquann-treated sample. Taquann method utilizes inexpensive materials and equipments mostly found in common biological laboratories, and prepares dry powder ready to make well-dispersed aerosol. This method and the chamber with direct injection system would facilitate the inhalation toxicity studies more relevant to human exposure.

  18. Interaction of amidated single-walled carbon nanotubes with protein by multiple spectroscopic methods

    Energy Technology Data Exchange (ETDEWEB)

    Li, Lili [China Pharmaceutical University, Nanjing 210009 (China); The Nursing College of Pingdingshan University, Pingdingshan 467000 (China); Lin, Rui [Yancheng Health Vocational and Technical College, Yancheng 224005 (China); He, Hua, E-mail: dochehua@163.com [China Pharmaceutical University, Nanjing 210009 (China); Key Laboratory of Drug Quality Control and Pharmacovigilance, Ministry of Education, China Pharmaceutical University, Nanjing 210009 (China); Sun, Meiling, E-mail: sml-nir@sohu.com [China Pharmaceutical University, Nanjing 210009 (China); Jiang, Li; Gao, Mengmeng [China Pharmaceutical University, Nanjing 210009 (China)

    2014-01-15

    The aim of this work was to investigate the detailed interaction between BSA and amidated single walled carbon nanotubes (e-SWNTs) in vitro. Ethylenediamine (EDA) was successfully linked on the surface of single-walled carbon nanotubes (SWNTs) via acylation to improve their dispersion and to introduce active groups. Bovine serum albumin (BSA) was selected as the template protein to inspect the interaction of e-SWNTs with protein. Decreases in fluorescence intensity of BSA induced by e-SWNTs demonstrated the occurrence of interaction between BSA and e-SWNTs. Quenching parameters and different absorption spectra for e-SWNTs–BSA show that the quenching effect of e-SWNTs was static quenching. Hydrophobic force had a leading contribution to the binding roles of BSA on e-SWNTs, which was confirmed by positive enthalpy change and entropy change. The interference of Na{sup +} with the quenching effect of e-SWNTs authenticated that electrostatic force existed in the interactive process simultaneously. The hydrophobicity of amino acid residues markedly increased with the addition of e-SWNTs viewed from UV spectra of BSA. The content of α-helix structure in BSA decreased by 6.8% due to the addition of e-SWNTs, indicating that e-SWNTs have an effect on the secondary conformation of BSA. -- Highlights: • The interaction between e-SWNTs and BSA was investigated by multiple spectroscopic methods. • Quenching mechanism was static quenching. • Changes in structure of BSA were inspected by synchronous fluorescence, UV–vis and CD spectrum.

  19. Deflection-based method for seismic response analysis of concrete walls: Benchmarking of CAMUS experiment

    Energy Technology Data Exchange (ETDEWEB)

    Basu, Prabir C. [Civil and Structural Engineering Division, Atomic Energy Regulatory Board (India)]. E-mail: pcb@aerb.gov.in; Roshan, A.D. [Civil and Structural Engineering Division, Atomic Energy Regulatory Board (India)

    2007-07-15

    A number of shake table tests had been conducted on the scaled down model of a concrete wall as part of CAMUS experiment. The experiments were conducted between 1996 and 1998 in the CEA facilities in Saclay, France. Benchmarking of CAMUS experiments was undertaken as a part of the coordinated research program on 'Safety Significance of Near-Field Earthquakes' organised by International Atomic Energy Agency (IAEA). Technique of deflection-based method was adopted for benchmarking exercise. Non-linear static procedure of deflection-based method has two basic steps: pushover analysis, and determination of target displacement or performance point. Pushover analysis is an analytical procedure to assess the capacity to withstand seismic loading effect that a structural system can offer considering the redundancies and inelastic deformation. Outcome of a pushover analysis is the plot of force-displacement (base shear-top/roof displacement) curve of the structure. This is obtained by step-by-step non-linear static analysis of the structure with increasing value of load. The second step is to determine target displacement, which is also known as performance point. The target displacement is the likely maximum displacement of the structure due to a specified seismic input motion. Established procedures, FEMA-273 and ATC-40, are available to determine this maximum deflection. The responses of CAMUS test specimen are determined by deflection-based method and analytically calculated values compare well with the test results.

  20. A simple and non-invasive method for nuclear transformation of intact-walled Chlamydomonas reinhardtii.

    Directory of Open Access Journals (Sweden)

    Sora Kim

    Full Text Available Genetic engineering in microalgae is gaining attraction but nuclear transformation methods available so far are either inefficient or require special equipment. In this study, we employ positively charged nanoparticles, 3-aminopropyl-functionalized magnesium phyllosilicate (aminoclay, approximate unit cell composition of [H2N(CH23]8Si8Mg6O12(OH4, for nuclear transformation into eukaryotic microalgae. TEM and EDX analysis of the process of transformation reveals that aminoclay coats negatively-charged DNA biomolecules and forms a self-assembled hybrid nanostructure. Subsequently, when this nanostructure is mixed with microalgal cells and plated onto selective agar plates with high friction force, cell wall is disrupted facilitating delivery of plasmid DNA into the cell and ultimately to the nucleus. This method is not only simple, inexpensive, and non-toxic to cells but also provides efficient transformation (5.03×10(2 transformants/µg DNA, second only to electroporation which needs advanced instrumentation. We present optimized parameters for efficient transformation including pre-treatment, friction force, concentration of foreign DNA/aminoclay, and plasticity of agar plates. It is also confirmed the successful integration and stable expression of foreign gene in Chlamydomonas reinhardtii through molecular methods.

  1. Similarity solutions of vertical plane wall plume based on finite analytic method

    Institute of Scientific and Technical Information of China (English)

    HUAI Wen-xin; ZENG Yu-hong

    2007-01-01

    The turbulent flow of vertical plane wall plume with concentration variation was studied with the finite analytical method. The k-epsilon model with the effect of buoyancy on turbulent kinetic energy and its dissipation rate was adopted. There were similarity solutions in the uniform environment for the system of equations including the equation of continuity, the equation of momentum along the flow direction and concentration, and equations of k, epsilon. The finite analytic method was applied to obtain the similarity solution. The calculated data of velocity, relative density difference, the kinetic energy of turbulence and its dissipation rate distribution for vertical plane plumes are in good agreement with the experimental data at the turbulent Schmidt number equal to 1.0. The variations of their maximum value along the direction of main flow were also given. It shows that the present model is good, i.e., the effect of buoyancy on turbulent kinetic energy and its dissipation rate should be taken into account, and the finite analytic method is effective.

  2. Wall Turbulence.

    Science.gov (United States)

    Hanratty, Thomas J.

    1980-01-01

    This paper gives an account of research on the structure of turbulence close to a solid boundary. Included is a method to study the flow close to the wall of a pipe without interferring with it. (Author/JN)

  3. Construction sustainability with adobe bricks type elements

    Directory of Open Access Journals (Sweden)

    Andreea Hegyi

    2016-06-01

    Full Text Available Sustainability is a criterion defined in the 80, which is essential in all fields of current activity. At the moment, it can not talk about development without being taken into account sustainability criteria. It presents the ensuring for an harmonious development, in line with current needs, without to endanger the possibility to develop and satisfy the needs of future generations. The buildings of adobe bricks-type elements ensure successfully the conditions imposed by this criterion. This type of construction ensures the responsible use of renewable natural resources, the possibility of reuse and recycling of materials, contributes to environmental protection and to pollution reduction, to energy saving and it provides a cleaner and healthier living environment. Not least, the buildings of this type are accessible in terms of cost and can contribute to the development of other fields such as eco-tourism.

  4. Moisture properties of the lightweight brick body

    Science.gov (United States)

    Čáchová, Monika; Koňáková, Dana; Vejmelková, Eva; Keppert, Martin; Černý, Robert

    2016-06-01

    Brick have been used for thousands years and during that time they went throw the long development. One of the possibilities how to changed properties of ceramic products is to change material compositions. This article is focused on utilization of lightening additives. Commonly used sawdust is compared with straw. The matter of measurement was to determine its influence on moisture properties. Basic physical properties were measured as well, since mainly open porosity has influence on water transport. Achieved results proved that utilization of straw leads to open porosity decrease. Particularly the amount of small pores (diameter under 1µm) went down. Regarding the moisture properties water vapor transport ability was decreased by adding straw in to the ceramic, while ability of water liquid transport remained unaffected.

  5. Utilization of Savannah Harbor river sediment as the primary raw material in production of fired brick.

    Science.gov (United States)

    Mezencevova, Andrea; Yeboah, Nortey N; Burns, Susan E; Kahn, Lawrence F; Kurtis, Kimberly E

    2012-12-30

    A laboratory-scale study was conducted to assess the feasibility of the production of fired bricks from sediments dredged from the Savannah Harbor (Savannah, GA, USA). The dredged sediment was used as the sole raw material, or as a 50% replacement for natural brick-making clay. Sediment bricks were prepared using the stiff mud extrusion process from raw mixes consisted of 100% dredged sediment, or 50% dredged sediment and 50% brick clay. The bricks were fired at temperatures between 900 and 1000 °C. Physical and mechanical properties of the dredged sediment brick were found to generally comply with ASTM criteria for building brick. Water absorption of the dredged sediment bricks was in compliance with the criteria for brick graded for severe (SW) or moderate (MW) weathering. Compressive strength of 100% dredged sediment bricks ranged from 8.3 to 11.7 MPa; the bricks sintered at 1000 °C met the requirements for negligible weathering (NW) building brick. Mixing the dredged sediment with natural clay resulted in an increase of the compressive strength. The compressive strength of the sediment-clay bricks fired at 1000 °C was 29.4 MPa, thus meeting the ASTM requirements for the SW grade building brick. Results of this study demonstrate that production of fired bricks is a promising and achievable productive reuse alternative for Savannah Harbor dredged sediments.

  6. NUMERICAL SIMULATION OF HYDRODYNAMIC CHARACTERISTICS ON AN ARC CROWN WALL USING VOLUME OF FLUID METHOD BASED ON BFC

    Institute of Scientific and Technical Information of China (English)

    LI Xue-yan; REN Bing; WANG Guo Yu; WANG Yong-xue

    2011-01-01

    In the present study,a new algorithm based on the Volume Of Fluid (vOF) method is developed to simulate the hydrodynamic characteristics on an arc crown wall.Structured grids are generated by the coordinate transform method in an arbitrary complex region.The Navier-Stokes equations for two-dimensional incompressible viscous flows are discretized in the Body Fitted Coordinate (BFC) system.The transformed SIMPLE algorithm is proposed to modify the pressure-velocity field and a transformed VOF method is used to trace the free surface.Hydrodynamic characteristics on an arc crown wall are obtained by the improved numerical model based on the BFC system (BFC model).The velocity field,the pressure field and the time profiles of the water surface near the arc crown wall obtained by using the BFC model and the Cartesian model are compared.The BFC model is verified by experimental results.

  7. Physical and Mechanical Properties of Compressed Earth Brick (CEB Containing Sugarcane Bagasse Ash

    Directory of Open Access Journals (Sweden)

    Ali Noorwirdawati

    2016-01-01

    Full Text Available The use of brick in construction is commonly used, especially in the construction of buildings and infrastructure. Various studies have been conducted to produce methods that can increase the strength of brick at the same time can reduce the cost of manufacturing bricks. In order to reduce cost of manufacturing, one of the solution applied was by using waste as part of bricks production materials. In this study, sugarcane bagasse (SuCaB ash was used as a part of compressed earth brick (CEB by replacing the quantity of cement for SuCaB ash. The study focused on the physical and mechanical properties of CEB containing SuCaB and the optimum percentage of SuCaB ash as partial cement replacement in CEB. There are 4 types of percentages used; 0%, 20%, 25% and 30% from cement content. All mixed use the same water content of 30% of cement content by weight and the ratio for cement: laterite soil used was 1: 6. A total of 72 specimen with size of 100mm × 50mm × 40mm was produced. The test conducted were Initial Rate Absorption Test (IRA, Density Test, Dimensions Test, Compression Test and Water Absorption Test. From the experimental results, the optimum SuCaB ash percentage as cement replacement in CEB was 20%. It recorded the highest compressive strength of 16.23 MPa at 28 days while for the Initial Rate Absorption test, it lies within the range specified. The density of CEB containing 20% of SuCaB shows slightly lower value where it decreased for about 0.4% from the control specimen. From this study, it can be concluded that waste materials such as sugarcane bagasse can be used as part of construction materials. However, further study needs to be conducted such as on the energy consumption, chemical properties and others to enhance the knowledge on this area before it can be applied into the brick production.

  8. Spectral triangulation: a 3D method for locating single-walled carbon nanotubes in vivo.

    Science.gov (United States)

    Lin, Ching-Wei; Bachilo, Sergei M; Vu, Michael; Beckingham, Kathleen M; Bruce Weisman, R

    2016-05-21

    Nanomaterials with luminescence in the short-wave infrared (SWIR) region are of special interest for biological research and medical diagnostics because of favorable tissue transparency and low autofluorescence backgrounds in that region. Single-walled carbon nanotubes (SWCNTs) show well-known sharp SWIR spectral signatures and therefore have potential for noninvasive detection and imaging of cancer tumours, when linked to selective targeting agents such as antibodies. However, such applications face the challenge of sensitively detecting and localizing the source of SWIR emission from inside tissues. A new method, called spectral triangulation, is presented for three dimensional (3D) localization using sparse optical measurements made at the specimen surface. Structurally unsorted SWCNT samples emitting over a range of wavelengths are excited inside tissue phantoms by an LED matrix. The resulting SWIR emission is sampled at points on the surface by a scanning fibre optic probe leading to an InGaAs spectrometer or a spectrally filtered InGaAs avalanche photodiode detector. Because of water absorption, attenuation of the SWCNT fluorescence in tissues is strongly wavelength-dependent. We therefore gauge the SWCNT-probe distance by analysing differential changes in the measured SWCNT emission spectra. SWCNT fluorescence can be clearly detected through at least 20 mm of tissue phantom, and the 3D locations of embedded SWCNT test samples are found with sub-millimeter accuracy at depths up to 10 mm. Our method can also distinguish and locate two embedded SWCNT sources at distinct positions.

  9. Wide dynamic range enrichment method of semiconducting single-walled carbon nanotubes with weak field centrifugation.

    Science.gov (United States)

    Reis, Wieland G; Tomović, Željko; Weitz, R Thomas; Krupke, Ralph; Mikhael, Jules

    2017-03-20

    The potential of single-walled carbon nanotubes (SWCNTs) to outperform silicon in electronic application was finally enabled through selective separation of semiconducting nanotubes from the as-synthesized statistical mix with polymeric dispersants. Such separation methods provide typically high semiconducting purity samples with narrow diameter distribution, i.e. almost single chiralities. But for a wide range of applications high purity mixtures of small and large diameters are sufficient or even required. Here we proof that weak field centrifugation is a diameter independent method for enrichment of semiconducting nanotubes. We show that the non-selective and strong adsorption of polyarylether dispersants on nanostructured carbon surfaces enables simple separation of diverse raw materials with different SWCNT diameter. In addition and for the first time, we demonstrate that increased temperature enables higher purity separation. Furthermore we show that the mode of action behind this electronic enrichment is strongly connected to both colloidal stability and protonation. By giving simple access to electronically sorted SWCNTs of any diameter, the wide dynamic range of weak field centrifugation can provide economical relevance to SWCNTs.

  10. Black Carbon And Co-Pollutants Emissions And Energy Efficiency From Bricks Production In Guanajuato, Mexico

    Science.gov (United States)

    Molina, L. T.; Zavala, M.; Maiz, P.; Monsivais, I.; Chow, J.; Munguia, J.

    2013-12-01

    In many parts of the world, small-scale traditional brick kilns are a notorious informal sector source of urban air pollution. Many are both inefficient and burn highly polluting fuels that emit significant levels of black carbon and other pollutants into local communities and to the atmosphere, resulting in severe health and environmental impacts. It is estimated that there are nearly 20,000 traditional brick kilns in Mexico, in which bricks are still produced as they have been for centuries. They are made by hand, dried in the sun, and generally fired in small, one chamber kilns that use various types of fuels, including plastic refuse, used tires, manure, wood scrap, and used motor oil. Three brick kilns, two traditional kilns and an improved kiln (MK2), were sampled as part of the SLCFs-Mexico campaign in Guanajuato, Mexico during March of 2013. The concept of the MK-2 involves covering the kiln with a dome and channeling the output of an active kiln through a second, identical loaded kiln for its additional filtration of the effluents. The results of energy efficiency and carbon mass balance calculations are presented for comparing the production efficiency and carbon emissions from the sampled kilns. Measurements included PM2.5 mass with quartz filters and temporally-resolved elemental carbon and organic carbon composition obtained using thermo-optical methods. The carbon emissions obtained with the mass balance method are compared with concurrent, high- time resolution, emissions measurements obtained using the Aerodyne mobile laboratory employing the tracer method (see abstract by Fortner et al.)

  11. Brane Brick Models and 2d (0,2) Triality

    CERN Document Server

    Franco, Sebastian; Seong, Rak-Kyeong

    2016-01-01

    We provide a brane realization of 2d (0,2) Gadde-Gukov-Putrov triality in terms of brane brick models. These are Type IIA brane configurations that are T-dual to D1-branes over singular toric Calabi-Yau 4-folds. Triality translates into a local transformation of brane brick models, whose simplest representative is a cube move. We present explicit examples and construct their triality networks. We also argue that the classical mesonic moduli space of brane brick model theories, which corresponds to the probed Calabi-Yau 4-fold, is invariant under triality. Finally, we discuss triality in terms of phase boundaries, which play a central role in connecting Calabi-Yau 4-folds to brane brick models.

  12. Application of Carbon Composite Bricks for Blast Furnace Hearth

    Science.gov (United States)

    Zuo, Haibin; Wang, Cong; Zhang, Jianliang; Zhao, Yongan; Jiao, Kexin

    Traditional refractory materials for blast furnace hearth lining are mainly composed of carbon bricks and the ceramic cup. However, these materials can't meet the demands for long service life design of blast furnaces. In this paper, a new refractory called carbon composite brick (CCB) was introduced, which combined the advantages of carbon bricks and the ceramic cup. In this case, the resistance of the CCB against corrosion was equal to the ceramic cup and the thermal conductivity of the CCB was equal to carbon bricks. From the results of more than 20 blast furnaces, the CCB could be well used in small blast furnaces and large blast furnaces. In the bad condition of low grade burden and high smelting intensity, the CCB gave full play to the role of cooling system, and effectively resisted the erosion of hot metal to improve the service life of blast furnaces.

  13. Utilization of crushed clay brick in cellular concrete production

    Directory of Open Access Journals (Sweden)

    Ali A. Aliabdo

    2014-03-01

    Full Text Available The main objective of this research program is to study the effect of using crushed clay brick as an alternative aggregate in aerated concrete. Two series of mixtures were designed to investigate the physico-mechanical properties and micro-structural analysis of autoclave aerated concrete and foamed concrete, respectively. In each series, natural sand was replaced with crushed clay brick aggregate. In both series results showed a significant reduction in unit weight, thermal conductivity and sound attenuation coefficient while porosity has increased. Improvement on compressive strength of autoclave aerated concrete was observed at a percentage of 25% and 50% replacement, while in foamed concrete compressive strength gradually decreased by increasing crushed clay brick aggregate content. A comparatively uniform distribution of pore in case of foamed concrete with natural sand was observed by scanning electron microscope, while the pores were connected mostly and irregularly for mixes containing a percentage higher than 25% clay brick aggregate.

  14. Computational fluid dynamics evaluation of liquid food thermal process in a brick shaped package

    Directory of Open Access Journals (Sweden)

    Pedro Esteves Duarte Augusto

    2012-03-01

    Full Text Available Food processes must ensure safety and high-quality products for a growing demand consumer creating the need for better knowledge of its unit operations. The Computational Fluid Dynamics (CFD has been widely used for better understanding the food thermal processes, and it is one of the safest and most frequently used methods for food preservation. However, there is no single study in the literature describing thermal process of liquid foods in a brick shaped package. The present study evaluated such process and the influence of its orientation on the process lethality. It demonstrated the potential of using CFD to evaluate thermal processes of liquid foods and the importance of rheological characterization and convection in thermal processing of liquid foods. It also showed that packaging orientation does not result in different sterilization values during thermal process of the evaluated fluids in the brick shaped package.

  15. Cellular Concrete Bricks with Recycled Expanded Polystyrene Aggregate

    OpenAIRE

    Juan Bosco Hernández-Zaragoza; Teresa López-Lara; Jaime Horta-Rangel; Carlos López-Cajún; Eduardo Rojas-González; García-Rodríguez, F. J.; Jorge Adue

    2013-01-01

    Cellular concrete bricks were obtained by using a lightweight mortar with recycled expanded polystyrene aggregate instead of sandy materials. After determining the block properties (absorption, compressive strength, and tensile stresses), it was found that this brick meets the requirements of the masonry standards used in Mexico. The obtained material is lighter than the commercial ones, which facilitates their rapid elaboration, quality control, and transportation. It is less permeable, whic...

  16. Seaweed biopolymers as additives for unfired clay bricks

    OpenAIRE

    Dove, Cassandra A.; Bradley, Fiona F.; Patwardhan, Siddharth V.

    2016-01-01

    Unfired clay bricks are an environmentally friendly alternative to conventional masonry materials such as fired bricks and concrete blocks but their use is currently limited by their relatively poor mechanical and durability properties. While products like cement and lime are commonly added to earthen materials in an effort to improve their physical performance, these additives can also have a negative influence on the overall environmental impact. The purpose of this research is to investiga...

  17. Utilization of crushed clay brick in cellular concrete production

    OpenAIRE

    Ali A. Aliabdo; Abd-Elmoaty M. Abd-Elmoaty; Hani H. Hassan

    2014-01-01

    The main objective of this research program is to study the effect of using crushed clay brick as an alternative aggregate in aerated concrete. Two series of mixtures were designed to investigate the physico-mechanical properties and micro-structural analysis of autoclave aerated concrete and foamed concrete, respectively. In each series, natural sand was replaced with crushed clay brick aggregate. In both series results showed a significant reduction in unit weight, thermal conductivity and ...

  18. Abdominal wall fat pad biopsy

    Science.gov (United States)

    Amyloidosis - abdominal wall fat pad biopsy; Abdominal wall biopsy; Biopsy - abdominal wall fat pad ... method of taking an abdominal wall fat pad biopsy . The health care provider cleans the skin on ...

  19. An Experimental Investigation of Mechanical Properties in Clay Brick Masonry by Partial Replacement of Fine Aggregate with Clay Brick Waste

    Science.gov (United States)

    Kumavat, Hemraj Ramdas

    2016-09-01

    The compressive stress-strain behavior and mechanical properties of clay brick masonry and its constituents clay bricks and mortar, have been studied by several laboratory tests. Using linear regression analysis, a analytical model has been proposed for obtaining the stress-strain curves for masonry that can be used in the analysis and design procedures. The model requires only the compressive strengths of bricks and mortar as input data, which can be easily obtained experimentally. Development of analytical model from the obtained experimental results of Young's modulus and compressive strength. Simple relationships have been identified for obtaining the modulus of elasticity of bricks, mortar, and masonry from their corresponding compressive strengths. It was observed that the proposed analytical model clearly demonstrates a reasonably good prediction of the stress-strain curves when compared with the experimental curves.

  20. Impact of synthesis methods on the transport of single walled carbon nanotubes in the aquatic environment.

    Science.gov (United States)

    Chowdhury, Indranil; Duch, Mathew C; Gits, Colton C; Hersam, Mark C; Walker, Sharon L

    2012-11-06

    In this study, a systematic approach has been followed to investigate the fate and transport of single walled carbon nanotubes (SWCNTs) from synthesis to environmentally relevant conditions. Three widely used SWCNT synthesis methods have been investigated in this study including high pressure carbon monoxide (HiPco), SWeNT CoMoCat, and electric arc discharge technique (EA). This study relates the transport of three SWCNTs (HiPco-D, SG65-D, and P2-D) with different synthesis methods and residual catalyst content revealing their influence on the subsequent fate of the nanotubes. To minimize nanotube bundling and aggregation, the SWCNTs were dispersed using the biocompatible triblock copolymer Pluronic, which allowed the comparison in the transport trends among these SWCNTs. After purification, the residual metal catalyst between the SWCNTs follows the trend: HiPco-D > SG65-D > P2-D. The electrophoretic mobility (EPM) and hydrodynamic diameter of SWCNTs remained insensitive to SWCNT type, pH, and presence of natural organic matter (NOM); but were affected by ionic strength (IS) and ion valence (K(+), Ca(2+)). In monovalent ions, the hydrodynamic diameter of SWCNTs was not influenced by IS, whereas larger aggregation was observed for HiPco-D with IS than P2-D and SG65-D in the presence of Ca(2+). Transport of HiPco-D in the porous media was significantly higher than SG65-D followed by P2-D. Release of HiPco-D from porous media was higher than SG65-D followed by P2-D, though negligible amount of all types of SWCNTs (acidic than SG65-D followed by P2-D, which is similar to the transport trend. Overall, it was observed that the synthesis methods resulted in distinctive breakthrough trends, which were correlated to metal content. These findings will facilitate the safe design of environmental friendly SWCNTs by minimizing mobility in aquatic environments.

  1. The decoration of multi-walled carbon nanotubes with nickel oxide nanoparticles using chemical method

    Science.gov (United States)

    Sahebian, S.; Zebarjad, S. M.; Vahdati Khaki, J.; Lazzeri, A.

    2016-07-01

    In this paper, nickel oxide (NiO) nanoparticles have been fabricated using wet method and deposited on the surface of multi-walled carbon nanotube (MWCNT). To do so, functional groups were introduced on the surface of MWCNTs by treating with concentrated nitric acid. Nickel oxide nanoparticles were formed on the surface of functionalized MWCNTs by incipient wetness impregnation of nickel nitrate, and the resultant product was calcinated in air atmosphere. Characteristics of the NiO/MWCNT were examined by various techniques, for example, Fourier transform spectroscopy (FTIR), X-ray diffraction analysis (XRD), transmission electron microscopy (TEM), thermogravimetric analyzer (TGA), and nitrogen adsorption-desorption isothermal as well as vibrating sample magnetometer (VSM). The FTIR spectra showed that carboxyl and hydroxyl functional groups existed on the surface of MWNTs after modification by concentrated nitric acid. The pattern of XRD indicated that MWNTs and nickel oxide nanoparticles coexisted in the NiO/MWCNT sample. The TEM images revealed that the NiO nanoparticles were distributed on the surface of the MWNTs, with the size ranging from 5 to 60 nm. Thermogravimetric analysis proved that NiO content decorated on MWCNTs was 80 and 15 wt%. The results of the Brunauer-Emmett-Teller (BET) data showed that the slight increment in the specific surface areas and porosities in the presence of the NiO nanoparticles on the surface of CNT.

  2. Production and characterization of nanocapsules encapsulated linalool by ionic gelation method using chitosan as wall material

    Directory of Open Access Journals (Sweden)

    Zuobing XIAO

    Full Text Available Abstract Linalool has been extensively applied in various fields, such as flavoring agent, perfumes, cosmetics and medical science. However, linalool is unstable, volatile and readily oxidizable. A sensitive substance can be encapsulated in a capsule, so encapsulation technology can solve these problems. In this paper, linalool-loaded nanocapsules (Lin-nanocapsules were prepared via the ionic gelation method and Lin-nanocapsules were characterized. The results of Fourier transformation infrared spectroscopy (FTIR showed that linalool was successfully encapsulated in the wall materials. Scanning electron microscopy (SEM results demonstrated that the shapes of Lin-nanocapsules, with smooth surfaces, were nearly spherical. Lin-nanocapsule average particle size was 352 nm and its polydispersity index (PDI was proved to be 0.214 by the results of dynamic light scattering (DLC. Thermogravimetric results indicated that linalool loading capacity (LC was 15.17%, and encapsulation could decrease linalool release and increase linalool retaining time under the high temperature. Oscillatory shear and steady-state shear measurements of Lin-nanocapsule emulsions were systematically investigated. The results of steady-state shear showed that Lin-nanocapsule emulsion, which was Newtonian only for high shear rate, was non-Newtonian. It was proved by oscillatory shear that when oscillation frequency changed from low to high, Lin-nanocapsules emulsion changed from viscous into elastic.

  3. An Effective Method for Establishing the Stage and Reflux Requirement of Three-product Dividing Wall Columns

    OpenAIRE

    I. Dejanović; Matijašević, Lj.; Olujić, Ž.

    2011-01-01

    This paper introduces an effective method for determination and optimisation of stage and reflux requirement of a three-product dividing wall column, arranged within a commercial software package by combining a fundamentally sound shortcut method providing reliable initial guesses and a detailed, four-column model, which appeared to be the most flexible among possible configurations, for both steady state and dynamic simulations. The applicability and usability of the method is demonstrate...

  4. Considering the Effect of Masonry Infill Walls on the Seismic Behavior of R/C Frames with a Simplified Method

    Directory of Open Access Journals (Sweden)

    Hasan Basri Aksoy

    2015-07-01

    Full Text Available Generally, in practice, effect of infill walls is not taken into account in the design or seismic performance assessment of RC buildings. In order to consider this effect, certain calculations and assumptions should be made. In this study, a simplified method, which considers this effect by employing a coefficient, is investigated and the criteria defined to employ this method is examined. A similar recommendation is investigated in detail given in the recent code namely “Determination of Seismically Vulnerable Buildings” in the context of “Urban Transformation Law”, where a single coefficient was defined to consider the effect of masonry infill walls. Column shear forces, inter-story drift ratio, mode shapes and the corresponding periods are the engineering demand parameters used in the assessments. Analytical model of a four-story RC building is generated and the effect of infill walls on its seismic response is investigated. It was found out that the coefficient proposed by the code “Determination of Seismically Vulnerable Buildings” to consider the effect of infill wall leads to column shear demands that are on the safe side in most of the cases. On the other hand, unsymmetrical arrangement of infill walls can cause torsion in the structure, which increases the shear demands in certain columns. Accordingly, it is suggested to add a further limitation in the application of the simplified method in the relevant item of the code “Determination of Seismically Vulnerable Buildings” when the infill walls cause torsion in the structural system.

  5. Spectral triangulation: a 3D method for locating single-walled carbon nanotubes in vivo

    Science.gov (United States)

    Lin, Ching-Wei; Bachilo, Sergei M.; Vu, Michael; Beckingham, Kathleen M.; Bruce Weisman, R.

    2016-05-01

    Nanomaterials with luminescence in the short-wave infrared (SWIR) region are of special interest for biological research and medical diagnostics because of favorable tissue transparency and low autofluorescence backgrounds in that region. Single-walled carbon nanotubes (SWCNTs) show well-known sharp SWIR spectral signatures and therefore have potential for noninvasive detection and imaging of cancer tumours, when linked to selective targeting agents such as antibodies. However, such applications face the challenge of sensitively detecting and localizing the source of SWIR emission from inside tissues. A new method, called spectral triangulation, is presented for three dimensional (3D) localization using sparse optical measurements made at the specimen surface. Structurally unsorted SWCNT samples emitting over a range of wavelengths are excited inside tissue phantoms by an LED matrix. The resulting SWIR emission is sampled at points on the surface by a scanning fibre optic probe leading to an InGaAs spectrometer or a spectrally filtered InGaAs avalanche photodiode detector. Because of water absorption, attenuation of the SWCNT fluorescence in tissues is strongly wavelength-dependent. We therefore gauge the SWCNT-probe distance by analysing differential changes in the measured SWCNT emission spectra. SWCNT fluorescence can be clearly detected through at least 20 mm of tissue phantom, and the 3D locations of embedded SWCNT test samples are found with sub-millimeter accuracy at depths up to 10 mm. Our method can also distinguish and locate two embedded SWCNT sources at distinct positions.Nanomaterials with luminescence in the short-wave infrared (SWIR) region are of special interest for biological research and medical diagnostics because of favorable tissue transparency and low autofluorescence backgrounds in that region. Single-walled carbon nanotubes (SWCNTs) show well-known sharp SWIR spectral signatures and therefore have potential for noninvasive detection and

  6. Organised structures in wall turbulence as deduced from stability theory-based methods

    Indian Academy of Sciences (India)

    P K Sen; S V Veeravalli; P W Carpenter; G Joshi; P S Josan

    2007-02-01

    In earlier work, we have explored the relevance of hydrodynamic stability theory to fully developed turbulent wall flows. Using an extended Orr-Summerfeld Equation, based on an anisotropic eddy-viscosity model, it was shown that there exists a wide range of unstable wave numbers (wall modes), which mimic some of the key features of turbulent wall flows. Here we present experimental confirmation for the same. There is good qualitative and quantitative agreement between theory and experiment. Once the dominant coherent structure is obtained from stability theory, control of turbulence would be the next logical step. As shown, the use of a compliant wall shows considerable promise. We also present some theoretical work for bypass transition (Klebanoff/K-modes), wherein the receptivity of a laminar boundary layer to a vortex sheet in the freestream has been studied. Further, it is shown that triadic interaction between K-modes, 2D TS waves and 3D TS waves can lead to rapid algebraic growth. A similar mechanism seems to carry over to inner wall structures in wall turbulence and perhaps this is the “root cause” for sustenance of turbulence.

  7. Crack propagation analysis of welded thin-walled joints using boundary element method

    Science.gov (United States)

    Mashiri, F. R.; Zhao, Xiao-Ling; Grundy, P.

    Tube-to-plate nodal joints under cyclic bending are widely used in the road transport and agricultural industry. The square hollow sections (SHS) used in these constructions are thin-walled and cold formed, and they have thicknesses of less than 4mm. Some fatigue failures have been observed. The weld undercut may affect the fatigue life of welded tubular joints especially for thin-walled sections. The undercut dimensions were measured using the silicon imprint technique. Modelling of thin-walled cruciform joints, as a simplification of welded tubular joints, is described in this paper to determine the effect of weld undercut on fatigue propagation life. The Boundary Element Analysis System Software (BEASY) is used. The results of the effect of weld toe undercut from this analysis are compared with results from previous research to determine the comparative reduction in fatigue life between thin-walled joints (T=3mm) and those made of thicker sections (T=20mm). The loss in fatigue strength of the thin-walled joints is found to be relatively more than that for thicker walled joints. A 3D model of a tube to plate T-joint is also modelled using the boundary element software, BEASY. The nodal joint consists of a square hollow section, 50×50×3 SHS, fillet welded to a 10-mm thick plate, and subjected to cyclic bending stress. Fatigue analyses are carried out and the results are compared with the only available S-N design curve.

  8. An improved method to evaluate the ideal no-wall beta limit from resonant field amplification measurements in JET

    Energy Technology Data Exchange (ETDEWEB)

    Liu Yueqiang; Chapman, I T; Saarelma, S; Gryaznevich, M P; Hender, T C; Howell, D F, E-mail: yueqiang.liu@ukaea.org.u [Euratom/UKAEA Fusion Association, Culham Science Centre, Abingdon, OX14 3DB (United Kingdom)

    2009-11-15

    Modelling the low-n, low frequency resonant field amplification (RFA) effects for JET plasmas, using the MHD code MARS-F, offers explanations to one of the recent observations made in experiments, namely a mismatch between the measured RFA threshold and the predicted no-wall beta limit according to ideal MHD calculations. The mismatch is minimized by applying a new way of determining the RFA threshold, based on evaluating the logarithmic derivative of the RFA amplitude as a function of the normalized plasma pressure. This improved method is shown, at least in theory, to be robust in predicting the no-wall beta limit for JET plasmas.

  9. Numerical Derivation of Strain Rate Effects on Material Properties of Masonry with Solid Clay Bricks

    Institute of Scientific and Technical Information of China (English)

    WEI Xueying; HAO Hong

    2006-01-01

    In this paper,numerical method is used to study the strain rate effect on masonry materials.A typical unit of masonry is selected to serve as a representative volume element (RVE).Numerical model of RVE is established with detailed distinctive modeling of brick and mortar with their respective dynamic material properties obtained from laboratory tests.The behavior of brick and mortar are characterized by a dynamic damage model that accounts for rate-sensitive and pressuredependent properties of masonry materials.Dynamic loads of different loading rates are applied to RVE.The equivalent homogenized uniaxial compressive strength,threshold strain and elastic modulus in three directions of the masonry are derived from the simulated responses of the RVE.The strain rate effect on the masonry material with clay brick and mortar,such as the dynamic increase factor (DIF) of the ultimate strength and elastic modulus as a function of strain rate are derived from the numerical results.

  10. Life Cycle Assessment and Life Cycle Cost Analysis of Magnesia Spinel Brick Production

    Directory of Open Access Journals (Sweden)

    Aysun Özkan

    2016-07-01

    Full Text Available Sustainable use of natural resources in the production of construction materials has become a necessity both in Europe and Turkey. Construction products in Europe should have European Conformity (CE and Environmental Product Declaration (EPD, an independently verified and registered document in line with the European standard EN 15804. An EPD certificate can be created by performing a Life Cycle Assessment (LCA study. In this particular work, an LCA study was carried out for a refractory brick production for environmental assessment. In addition to the LCA, the Life Cycle Cost (LCC analysis was also applied for economic assessment. Firstly, a cradle-to-gate LCA was performed for one ton of magnesia spinel refractory brick. The CML IA method included in the licensed SimaPro 8.0.1 software was chosen to calculate impact categories (namely, abiotic depletion, global warming potential, acidification potential, eutrophication potential, human toxicity, ecotoxicity, ozone depletion potential, and photochemical oxidation potential. The LCC analysis was performed by developing a cost model for internal and external cost categories within the software. The results were supported by a sensitivity analysis. According to the results, the production of raw materials and the firing process in the magnesia spinel brick production were found to have several negative effects on the environment and were costly.

  11. Tracked ultrasound calibration studies with a phantom made of LEGO bricks

    Science.gov (United States)

    Soehl, Marie; Walsh, Ryan; Rankin, Adam; Lasso, Andras; Fichtinger, Gabor

    2014-03-01

    In this study, spatial calibration of tracked ultrasound was compared by using a calibration phantom made of LEGO® bricks and two 3-D printed N-wire phantoms. METHODS: The accuracy and variance of calibrations were compared under a variety of operating conditions. Twenty trials were performed using an electromagnetic tracking device with a linear probe and three trials were performed using varied probes, varied tracking devices and the three aforementioned phantoms. The accuracy and variance of spatial calibrations found through the standard deviation and error of the 3-D image reprojection were used to compare the calibrations produced from the phantoms. RESULTS: This study found no significant difference between the measured variables of the calibrations. The average standard deviation of multiple 3-D image reprojections with the highest performing printed phantom and those from the phantom made of LEGO® bricks differed by 0.05 mm and the error of the reprojections differed by 0.13 mm. CONCLUSION: Given that the phantom made of LEGO® bricks is significantly less expensive, more readily available, and more easily modified than precision-machined N-wire phantoms, it prompts to be a viable calibration tool especially for quick laboratory research and proof of concept implementations of tracked ultrasound navigation.

  12. Air pollution tolerance index of plants around brick kilns in Rawalpindi, Pakistan.

    Science.gov (United States)

    Achakzai, Khanoranga; Khalid, Sofia; Adrees, Muhammad; Bibi, Aasma; Ali, Shafaqat; Nawaz, Rab; Rizwan, Muhammad

    2017-04-01

    In any contaminated environment, the sensitive plant species can serve as bio-indicator of air pollution while tolerant plant species can act as a sink for air pollutants. Air pollution tolerance index (APTI) is an important tool to screen out plants based on their tolerance or sensitivity level to different air pollutants. The present study was aimed to identify the sensitive and tolerant plant species in the vicinity of brick kilns in the Rawalpindi city. To determine the susceptibility level of the selected plant species, four biochemical parameters, ascorbic acid, total chlorophyll content, relative water content and pH of leaf extract, were assessed and APTI was calculated. Plant sampling was carried out with increasing distance of 100, 300 and 500 m around three brick kiln sites and APTI values were calculated by following the standard methods. The results of the study revealed that among nine studied plant species, Calotropis procera (APTI = 20.05) and Althernanthera pungens (APTI = 17.13) were found to be the most tolerant species, whereas Malva neglecta (APTI = 8.83) was found to be the most sensitive species. Inconsistent trend of variations was seen in the APTI values at each site. The present study suggested that the most tolerant species, C. procera and A. pungens, could be grown in the vicinity of such pollution sources as a remedial measure of brick kiln pollution.

  13. Modeling of drag reduction in turbulent channel flow with hydrophobic walls by FVM method and weakly-compressible flow equations

    Institute of Scientific and Technical Information of China (English)

    Ling Li; Ming-Shun Yuan

    2011-01-01

    In this paper the effects of hydrophobic wall on skin-friction drag in the channel flow are investigated through large eddy simulation on the basis of weaklycompressible flow equations with the MacCormack's scheme on collocated mesh in the FVM framework. The slip length model is adopted to describe the behavior of the slip velocities in the streamwise and spanwise directions at the interface between the hydrophobic wall and turbulent channel flow. Simulation results are presented by analyzing flow behaviors over hydrophobic wall with the Smagorinky subgrid-scale model and a dynamic model on computational meshes of different resolutions. Comparison and analysis are made on the distributions of timeaveraged velocity, velocity fluctuations, Reynolds stress as well as the skin-friction drag. Excellent agreement between the present study and previous results demonstrates the accuracy of the simple classical second-order scheme in representing turbulent vertox near hydrophobic wall. In addition, the relation of drag reduction efficiency versus time-averaged slip velocity is established. It is also found that the decrease of velocity gradient in the close wall region is responsible for the drag reduction. Considering its advantages of high calculation precision and efficiency, the present method has good prospect in its application to practical projects.

  14. Method for aortic wall strain measurement with three-dimensional ultrasound speckle tracking and fitted finite element analysis.

    Science.gov (United States)

    Karatolios, Konstantinos; Wittek, Andreas; Nwe, Thet Htar; Bihari, Peter; Shelke, Amit; Josef, Dennis; Schmitz-Rixen, Thomas; Geks, Josef; Maisch, Bernhard; Blase, Christopher; Moosdorf, Rainer; Vogt, Sebastian

    2013-11-01

    Aortic wall strains are indicators of biomechanical changes of the aorta due to aging or progressing pathologies such as aortic aneurysm. We investigated the potential of time-resolved three-dimensional ultrasonography coupled with speckle-tracking algorithms and finite element analysis as a novel method for noninvasive in vivo assessment of aortic wall strain. Three-dimensional volume datasets of 6 subjects without cardiovascular risk factors and 2 abdominal aortic aneurysms were acquired with a commercial real time three-dimensional echocardiography system. Longitudinal and circumferential strains were computed offline with high spatial resolution using a customized commercial speckle-tracking software and finite element analysis. Indices for spatial heterogeneity and systolic dyssynchrony were determined for healthy abdominal aortas and abdominal aneurysms. All examined aortic wall segments exhibited considerable heterogenous in-plane strain distributions. Higher spatial resolution of strain imaging resulted in the detection of significantly higher local peak strains (p ≤ 0.01). In comparison with healthy abdominal aortas, aneurysms showed reduced mean strains and increased spatial heterogeneity and more pronounced temporal dyssynchrony as well as delayed systole. Three-dimensional ultrasound speckle tracking enables the analysis of spatially highly resolved strain fields of the aortic wall and offers the potential to detect local aortic wall motion deformations and abnormalities. These data allow the definition of new indices by which the different biomechanical properties of healthy aortas and aortic aneurysms can be characterized. Copyright © 2013 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

  15. Environmental Impacts and Embodied Energy of Construction Methods and Materials in Low-Income Tropical Housing

    Directory of Open Access Journals (Sweden)

    Arman Hashemi

    2015-06-01

    Full Text Available This paper evaluates the current conditions of Ugandan low-income tropical housing with a focus on construction methods and materials in order to identify the key areas for improvement. Literature review, site visits and photographic surveys are carried out to collect relevant information on prevailing construction methods/materials and on their environmental impacts in rural areas. Low quality, high waste, and energy intensive production methods, as well as excessive soil extraction and deforestation, are identified as the main environmental damage of the current construction methods and materials. The embodied energy is highlighted as the key area which should be addressed to reduce the CO2 emissions of low-income tropical housing. The results indicate that the embodied energy of fired bricks in Uganda is up to 5.7 times more than general clay bricks. Concrete walling is identified as a much more environmentally friendly construction method compared to brick walling in East African countries. Improving fuel efficiency and moulding systems, increasing access to renewable energy sources, raising public awareness, educating local manufacturers and artisans, and gradual long-term introduction of innovative construction methods and materials which are adapted to local needs and conditions are some of the recommended actions to improve the current conditions.

  16. Equivalent Strut Method for the Modelling of Masonry Infill Walls in the Nonlinear Static Analysis of Buildings

    Science.gov (United States)

    Adukadukam, A.; Sengupta, A. K.

    2013-05-01

    In the seismic analysis of a framed building with masonry infill walls, it is necessary to model the effect of the walls on the lateral stiffness, strength and ductility of the building. The equivalent strut method is convenient for modelling the walls in a large building. However, an appropriate axial load versus deformation relationship for the strut is required in a nonlinear static method of seismic analysis, such as the pushover analysis. The present study proposes a nonlinear axial hinge property for the strut, with suitable performance levels. First, the equivalent strut method and the suitability of two approaches available in the literature for modelling the properties of the struts, are briefly discussed. Next, the nonlinear axial load versus deformation relationship is developed based on experimental data compiled from the literature. The parabolic-plastic relationship is idealized as a tri-linear axial hinge property, so that it can be incorporated in commercial software for undertaking pushover analysis. Next, the use of the hinge property is demonstrated in the pushover analyses of two framed reinforced concrete buildings. The pushover curves based on the proposed hinge property shows improved modelling of the inelastic drifts of the buildings. Although the modelling of a wall using a single strut has limitations, the proposed methodology is practical for a pushover analysis of a building.

  17. Modified method of T-tube placement in cases of ruptured choledochal cyst having complete loss of anterior wall

    Directory of Open Access Journals (Sweden)

    Ahmed Intezar

    2011-01-01

    Full Text Available Survival rates for infants and children who have choledochal cyst with or without spontaneous rupture have improved dramatically in the past decades. Despite excellent long-term survival for patients with choledochal cyst who undergo elective surgery, many significant complications can occur in the patients being operated in emergency for rupture of the cyst. Spontaneous rupture of the cyst is one such problem resulting in considerable morbidity and mortality in these patients. Majority of surgeons manage these cases with T-tube external drainage. The conventional methods of T-tube placement for long period has remained simple as described in choledochotomies where there is no deficit of the walls of common bile duct (CBD. The present technique has been designed specially for the cases of ruptured choledochal cyst, where the wall of the CBD gets necrosed leaving behind a long gap between the two ends. In these cases, placement of T-tube with conventional method is not possible because there is no wall to suture together, and make the CBD water tight again to prevent leakage of bile. We found only two patients of spontaneous rupture of choledochal cyst with a long gap between two ends of CBD because of necrosed anterior wall. In both of these patients, it was not possible to put T-tube with traditional method and one would have to opt for primary definitive repair despite poor general condition of patients.

  18. Comparison between methods using copper, lanthanum, and colorimetry for the determination of the cation exchange capacity of plant cell walls.

    Science.gov (United States)

    Wehr, J Bernhard; Blamey, F Pax C; Menzies, Neal W

    2010-04-28

    The determination of the cation exchange capacity (CEC) of plant cell walls is important for many physiological studies. We describe the determination of cell wall CEC by cation binding, using either copper (Cu) or lanthanum (La) ions, and by colorimetry. Both cations are strongly bound by cell walls, permitting fast and reproducible determinations of the CEC of small samples. However, the dye binding methods using two cationic dyes, Methylene Blue and Toluidine Blue, overestimated the CEC several-fold. Column and centrifugation methods are proposed for CEC determination by Cu or La binding; both provide similar results. The column method involves packing plant material (2-10 mg dry mass) in a chromatography column (10 mL) and percolating with 20 bed volumes of 1 mM La or Cu solution, followed by washing with deionized water. The centrifugation method uses a suspension of plant material (1-2 mL) that is centrifuged, and the pellet is mixed three times with 10 pellet volumes of 1 mM La or Cu solution followed by centrifugation and final washing with deionized water. In both methods the amount of La or Cu bound to the material was determined by spectroscopic methods.

  19. Hole Pattern Design of Fired Shale Hollow Brick%烧结页岩空心砖孔型结构设计研究

    Institute of Scientific and Technical Information of China (English)

    黄孝云; 朱惠英; 陶尚儒; 卢凌寰; 张小静

    2013-01-01

    Fired shale hollow brick is a new type of energy-saving walling material. The factors affected the architectural designing of the shale hollow bricks were studied and discussed on its mechanical and thermal properties, proposing the best selection of different hole shapes, number of holes, holes arranged in size and platoon, hole wall thickness and hole chamfer.%  烧结页岩空心砖是一种新型的节能墙体材料。从力学和热工性能的角度,研究讨论了烧结页岩空心砖孔型结构设计的影响因素。提出不同孔洞形状、孔洞大小、孔洞排列及排数、孔壁厚度、孔洞倒角的最佳选取方案。

  20. The influence of water saturation on mechanical properties of ceramic bricks – tests on 19th- century and contemporary bricks

    Directory of Open Access Journals (Sweden)

    Matysek, P.

    2016-09-01

    Full Text Available The paper presents test results concerning ceramic bricks produced in 1880’s. Bricks were obtained from a building erected as part of Archduke Rudolf barracks in Krakow. The tests helped to specify changes in brick compressive strength and hardness, caused by water saturation in the ceramic material. For comparison purposes, tests were also carried out on contemporary bricks. Tests showed that mechanical properties of the ceramic bricks in the water saturation state were worse than in the dry state. The impact of strong brick moisture on changes of mechanical parameters is essential in terms of safety assessment for brick structures.En el artículo se presentan los resultados del estudio de los ladrillos cerámicos producidos en los años 80 del siglo XIX. Los ladrillos se obtuvieron del edificio que forma parte de un conjunto de cuarteles del archiduque Rudolfo en Cracovia en Polonia. En los estudios se han determinado los cambios de la resistencia a la compresión y la dureza de los ladrillos, por efecto de la saturación de agua del material cerámico. A efectos comparativos, se han realizado también estudios de ladrillos producidos en la actualidad. Se ha comprobado que la saturación de agua de los ladrillos cerámicos lleva consigo una considerable disminución de las propiedades mecánicas. Por lo tanto, el impacto de la alta humedad de los ladrillos sobre el cambio de las propiedades mecánicas constituye un factor significativo en la evaluación de la seguridad en las construcciones de ladrillo.

  1. Cyclic Behavior of Mortarless Brick Joints with Different Interlocking Shapes

    Directory of Open Access Journals (Sweden)

    Hongjun Liu

    2016-03-01

    Full Text Available The framed structure infilled with a mortarless brick (MB panel exhibits considerable in-plane energy dissipation because of the relative sliding between bricks and good out-of-plane stability resulting from the use of interlocking mechanisms. The cyclic behaviors of MB are investigated experimentally in this study. Two different types of bricks, namely non-interlocking mortarless brick (N-IMB and interlocking mortarless brick (IMB, are examined experimentally. The cyclic behavior of all of the joints (N-IMB and IMB are investigated in consideration of the effects of interlocking shapes, loading compression stress levels and loading cycles. The hysteretic loops of N-IMB and IMB joints are obtained, according to which a mechanical model is developed. The Mohr–Coulomb failure criterion is employed to describe the shear failure modes of all of the investigated joints. A typical frictional behavior is observed for the N-IMB joints, and a significant stiffening effect is observed for the IMB joints during their sliding stage. The friction coefficients of all of the researched joints increase with the augmentation of the compression stress level and improvement of the smoothness of the interlocking surfaces. An increase in the loading cycle results in a decrease in the friction coefficients of all of the joints. The degradation rate (DR of the friction coefficients increases with the reduction in the smoothness of the interlocking surface.

  2. esearch and Application of Burned Microporous High Alumian—Graphite(Al/C) Brick in Blast Furnace

    Institute of Scientific and Technical Information of China (English)

    ZHANXiaoming; SONGMusen

    1999-01-01

    This paper inroduces the research background,technology,product property and application of burned microporous high alumina-graphite brick (Al2O3-C brick) used in blast furnace,The difference of property between Al2O3-C brick and other blast furnace refractories is discussed .The results of simulative tests show that ,Al2O3-C brick has good alkali resistance,slag resistance,thermal shock resistance,oxidation resistance,high thermal conductivity,low permeability and low solubility in molten iron,The brick with micropores of average radius less than 1μm has been successively applied to fourteen blast furnaces, the lining life of the brick is almost as long as that of Si3N4 bonded SiC brick Al2O3-C brick will be widely used in lower stack ,belly,bosh and hearth in the future.

  3. Electrodiffusion Method of Near-Wall Flow Diagnostics in Microfluidic Systems

    Directory of Open Access Journals (Sweden)

    Tihona J.

    2015-01-01

    Full Text Available The electrodiffusion technique has been mostly used for the near-wall flow diagnostics on large scales. A novel technique for fabrication of plastic microfluidic systems with integrated metal microelectrodes (called technique of sacrificed substrate enables us to produce microfluidic devices with precisely shaped sensors for wall shear stress measurements. Several micrometer thick gold sensors, which are built-in a plastic substrate, exhibit good mechanical resistance and smoothness. Proper functioning of prepared chips with microsensors has been first tested in various calibration experiments (polarization curve, sensor response to polarization set-up, steady flow calibration, temperature dependence of diffusivity. Our first results obtained for separating/reattaching flow behind a backward-facing step and for gas-liquid Taylor flow in microchannels then demonstrate its applicability for the detection of near-wall flow reversal, the delimitation of flow - recirculation zones, and the determination of wall shear stress response to moving bubbles. Other applications of these sensors in microfluidics (e.g. characterization of liquid films, capillary waves, bubbles or drops can be also envisaged.

  4. Crystallizer with internal scraped cooled wall and method of use thereof

    NARCIS (Netherlands)

    Evers, J.A.

    2008-01-01

    Apparatus for separating solids from a mixture or solution, comprising an outer wall provided with an inlet for the mixture or solution and provided with a first discharge for discharging an ice slurry and a second discharge for discharging a salt slurry, one or more raking or scraping elements for

  5. The use of recycled paper processing residues in making porous brick with reduced thermal conductivity

    OpenAIRE

    SÜTÇÜ, Mücahit; AKKURT, Sedat

    2009-01-01

    Production of porous and light-weight bricks with reduced thermal conductivity and acceptable compressive strength is accomplished. Paper processing residues were used as an additive to an earthenware brick to produce the pores. SEM-EDS, XRD, XRF and TG-DTA analysis of the paper waste and brick raw material were performed. Mixtures containing brick raw materials and the paper waste were prepared at different proportions (up to 30 wt%). The granulated powder mixtures were compressed in a hydra...

  6. Modelling of URM Walls Retrofitted with Cable:A Comparison Between a Basic Mechanical Model and Distinct Element Method

    Institute of Scientific and Technical Information of China (English)

    ZHUGE Yan; CHUANG Shihwei

    2006-01-01

    The Australian love of "heritage" buildings (most of them are unreinforced masonry (URM)) means that greater attention is required to secure their performance under seismic or impact loading in the future.A research project has been carried out to develop a new,economic and high strength retrofitting technique for masonry structures.A series of experimental testing on URM walls retrofitted with an innovative technique by cable system have been conducted.In this paper,an analytical model which is based on distinct element method(DEM) is developed to simulate the behaviour of retrofitted walls.In DEM,a solid is represented as an assembly of discrete blocks.Joints are modelled as interface between distinct bodies.It is a dynamic process and specially designed to model the behaviour of discontinuities.In order to assist the practising engineers to design this new retrofitted wall system,a simple mechanical model was also developed to predict the strength of the retrofitted walls.The results obtained from this simple mechanical model are compared with those from both experiments and distinct element model.

  7. A method for modifying two-dimensional adaptive wind-tunnel walls including analytical and experimental verification

    Science.gov (United States)

    Everhart, J. L.

    1983-01-01

    The theoretical development of a simple and consistent method for removing the interference in adaptive-wall wind tunnels is reported. A Cauchy integral formulation of the velocities in an imaginary infinite extension of the real wind-tunnel flow is obtained and evaluated on a closed contour dividing the real and imaginary flow. The contour consists of the upper and lower effective wind-tunnel walls (wall plus boundary-layer displacement thickness) and upstream and downstream boundaries perpendicular to the axial tunnel flow. The resulting integral expressions for the streamwise and normal perturbation velocities on the contour are integrated by assuming a linear variation of the velocities between data-measurement stations along the contour. In an iterative process, the velocity components calculated on the upper and lower boundaries are then used to correct the shape of the wall to remove the interference. Convergence of the technique is shown numerically for the cases of a circular cylinder and a lifting and nonlifting NACA 0012 airfoil in incompressible flow. Experimental convergence at a transonic Mach number is demonstrated by using an NACA 0012 airfoil at zero lift.

  8. Compressive strength of brick masonry made with weak mortars

    DEFF Research Database (Denmark)

    Pedersen, Erik Steen; Hansen, Klavs Feilberg

    2013-01-01

    The use of weak mortar has a number of advantages (e.g. prevention of expansion joints, environmental issues). However, according to EC6, the strength of masonry vanishes when the compressive strength of the mortar approaches zero. In reality the presence of even unhardened mortar kept in place...... in the joint will ensure a certain level of load-carrying capacity. This is due to the interaction between compression in the weak mortar and tension in the adjacent bricks. This paper proposes an expression for the compressive strength of masonry made with weak lime mortars (fm... of masonry depends only on the strength of the bricks. A compression failure in masonry made with weak mortars occurs as a tension failure in the bricks, as they seek to prevent the mortar from being pressed out of the joints. The expression is derived by assuming hydrostatic pressure in the mortar joints...

  9. Water extraction out of mortar during brick laying: A NMR study

    NARCIS (Netherlands)

    Brocken, H.J.P.; Spiekman, M.E.; Pel, L.; Kopinga, K.; Larbi, J.A.

    1998-01-01

    The water extraction out of mortar during brick laying was studied using nuclear magnetic resonance. The experiments show that using a fired-clay brick, the water is extracted out of the mortar within 3 minutes, whereas in the case of a sand-lime brick this takes about 10 minutes. Prewetting a fired

  10. 78 FR 21106 - Silica Bricks and Shapes From the People's Republic of China: Postponement of Preliminary...

    Science.gov (United States)

    2013-04-09

    ... International Trade Administration Silica Bricks and Shapes From the People's Republic of China: Postponement of... of silica bricks and shapes from the People's Republic of China.\\1\\ The period of investigation is... investigation is currently due no later than April 24, 2013. \\1\\ See Silica Bricks and Shapes From the...

  11. Water extraction out of mortar during brick laying: A NMR study

    NARCIS (Netherlands)

    Brocken, H.J.P.; Spiekman, M.E.; Pel, L.; Kopinga, K.; Larbi, J.A.

    1998-01-01

    The water extraction out of mortar during brick laying was studied using nuclear magnetic resonance. The experiments show that using a fired-clay brick, the water is extracted out of the mortar within 3 minutes, whereas in the case of a sand-lime brick this takes about 10 minutes. Prewetting a fired

  12. 75 FR 57442 - Certain Magnesia Carbon Bricks from the People's Republic of China: Countervailing Duty Order

    Science.gov (United States)

    2010-09-21

    .... industry with respect to imports of MCBs from the PRC and Mexico. See Certain Magnesia Carbon Bricks from... International Trade Administration Certain Magnesia Carbon Bricks from the People's Republic of China... order on certain magnesia carbon bricks (MCBs) from the People's Republic of China (PRC). On September...

  13. 75 FR 56556 - Certain Magnesia Carbon Bricks From China and Mexico

    Science.gov (United States)

    2010-09-16

    ... COMMISSION Certain Magnesia Carbon Bricks From China and Mexico Determinations On the basis of the record \\1... from China and Mexico of certain magnesia carbon bricks, provided for in subheadings 6902.10.10, 6902... retarded, by reason of imports from Mexico of certain magnesia carbon bricks. Background The...

  14. 76 FR 78885 - Certain Magnesia Carbon Bricks From Mexico: Notice of Rescission of Antidumping Duty...

    Science.gov (United States)

    2011-12-20

    ... International Trade Administration Certain Magnesia Carbon Bricks From Mexico: Notice of Rescission of... antidumping duty order on certain magnesia carbon bricks from Mexico for the period of review (POR) of March... review of the antidumping duty order on certain magnesia carbon bricks from Mexico for the POR....

  15. Neonatal chest wall suspension splint: a novel and noninvasive method for support of lung volume.

    Science.gov (United States)

    Miller, Thomas L; Palmer, Charles; Shaffer, Thomas H; Wolfson, Marla R

    2005-06-01

    Surfactant and musculoskeletal immaturity results in lower compliance of the lung relative to the chest wall, with clinical manifestations of low lung volume, marked chest wall retractions (CWR), and thoracoabdominal asynchrony. Inspiratory efforts are dissipated on distorting the chest wall inward rather than recruiting lung volumes. The current study tests the hypothesis that a novel neonatal chest wall suspension splint (SP), designed to provide stability to the compliant chest wall, would reduce inspiratory chest wall retractions and improve lung volumes. Nine preterm infants (29 +/- 1 SE weeks of gestation; 1.59 +/- 0.27 SE kg study weight) were studied at 16 +/- 5 SE days of life at baseline (BL) and following application of the front plate (FP) and the full SP (Hug n Snug Neonatal Chest Splint, Respironics, Inc.). Phase angle of thoracoabdominal motion, CWR, functional residual capacity (FRC), and pulmonary function were evaluated during spontaneous breathing. Compared to BL, there was a significant decrease in anterior CWR (2.21 +/- 0.91 SE vs. 0.25 +/- 0.09 SE mm; P < 0.05), an increase in FRC (16.6 +/- 2.8 SE vs. 27.8 +/- 5.5 SE ml/kg; P < 0.05) and tidal volume (4.8 +/- 1.5 SE vs. 7.3 +/- 1.4 SE ml/kg; P < 0.05), minimal effect on pulmonary compliance (1.98 +/- 0.50 SE vs. 1.72 +/- 0.30 SE ml/cmH2O/kg), and a trend for a decrease in phase angle (128.4 +/- 10.9 SE vs. 111.8 +/- 19.3 SE) with the application of the splint. FRC correlated inversely with severity of CWR across all conditions (P < 0.05, r = -0.68). Phase angle was directly correlated to anterior CWR (r = 0.72; P < 0.05) and correlated inversely with FRC (P < 0.005; r = -0.56). We speculate that by improving CW stability, the use of this splint may reduce the energetic requirements of breathing and, potentially, the need for more invasive ventilatory support in the neonate.

  16. Simplified architectural method for the solar control optimization of awning and external wall in houses in hot and dry climates

    OpenAIRE

    Gómez Muñoz, Víctor Manuel; Porta Gándara, Migual Ángel

    2003-01-01

    In extremely hot and dry climates, like northwestern Mexico, solar gain reduction in houses using solar passive techniques is important for improving comfort inside the construction and to save costs in electrical cooling during the whole year, because the winter season is also hot in those regions. A new one-dimension method is proposed to analyze the interaction between two common shading devices: awnings and external walls to reduce insulation on the facade and inside the house due to fene...

  17. ROLE OF SOME TREATMENTS ON ENHANCING THE ECO-FRIENDLY UTILIZATION OF LIGNOCELLULOSIC WASTES IN PRODUCTION OF CEMENT-FIBER BRICKS

    Directory of Open Access Journals (Sweden)

    Altaf Halim Basta

    2011-04-01

    Full Text Available Rice straw (RS and sawdust (SD were evaluated for the manufacturing of fiber-cement bricks. The utilization of these bio-wastes will contribute to the reduction of the environmental impact of waste disposal. Pre-treating the fiber wastes, mechanically and/or chemically, was carried out before mixing them with cement and the appropriate amount of water. This approach was done for trials to reduce the tendency of fibers to absorb water, and consequently overcome the side effects of exposing the fiber-bricks to humidity. Different chemical treating agents, based on organic and inorganic materials, were used, e.g., gelatin-hexamine mixture, sodium silicate, and linseed oil. The results obtained show that the investigated organic treatments, especially linseed oil, were effective to reduce the water retention value (WRV of RS and SD by 60% and 65%, respectively. The treatment provided bricks with compressive strengths of 4.9 MPa and 5.4 MPa, respectively. According to the Engineering Encyclopedia of Building standards, these values are suitable for construction purposes. The bricks manufactured from linseed oil-treated fibers with cement and Nitobond AR may be suited for load-bearing walls, since the compressive strength reached is 7.8 to 8.6 MPa.

  18. Very Long Single and Few-Walled Boron Nitride Nanotubes via the Pressurized Vapor/Condenser Method

    Science.gov (United States)

    Smith, Michael W.; Jordan, Kevin C.; Park, Cheol; Kim, Jae-Woo; Lillehei, Peter T.; Crooks, Roy; Harrison, Joycelyn S.

    2009-01-01

    A new method for producing long, small diameter, single and few-walled, boron nitride nanotubes (BNNTs) in macroscopic quantities is reported. The pressurized vapor/condenser (PVC) method produces, without catalysts, highly crystalline, very long, small diameter, BNNTs. Palm-sized, cotton-like masses of BNNT raw material were grown by this technique and spun directly into centimeters-long yarn. Nanotube lengths were observed to be 100 times that of those grown by the most closely related method. Self-assembly and growth models for these long BNNTs are discussed.

  19. Very long single- and few-walled boron nitride nanotubes via the pressurized vapor/condenser method

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Michael W. [NASA Langley Research Center, Hampton, VA (United States); Jordan, Kevin C. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Park, Cheol [NASA Langley Research Center, Hampton, VA (United States); Kim, Jae-Woo [NASA Langley Research Center, Hampton, VA (United States); Lillehei, Peter T. [NASA Langley Research Center, Hampton, VA (United States); Crooks, Roy [NASA Langley Research Center, Hampton, VA (United States); Harrison, Joycelyn S. [NASA Langley Research Center, Hampton, VA (United States)

    2009-11-01

    Boron nitride nanotubes (BNNTs) are desired for their exceptional mechanical, electronic, thermal, structural, textural, optical, and quantum properties. A new method for producing long, small-diameter, single- and few-walled, boron nitride nanotubes (BNNTs) in macroscopic quantities is reported. The pressurized vapor/condenser (PVC) method produces, without catalysts, highly crystalline, very long, small-diameter, BNNTs. Palm-sized, cotton-like masses of BNNT raw material were grown by this technique and spun directly into centimeters-long yarn. Nanotube lengths were observed to be 100 times that of those grown by the most closely related method. Self-assembly and growth models for these long BNNTs are discussed.

  20. Preliminary TES design optimization study for a simple periodic brick plant

    Energy Technology Data Exchange (ETDEWEB)

    Drake, J.B.; Olszewski, M.; Solomon, A.D. [Oak Ridge National Lab., TN (United States)] [and others

    1989-03-01

    A general optimization method has been developed for maximizing the return on investment for a brick plant re-using waste heat with the capability of storing energy over periods when a kiln is not operating. The duct connections between devices and storage along with the operating schedule of flow rates in these ducts are the independent variables available for control. A combination of combinatorial search algorithms along with a dynamic programming model and the simplex method are layered to provide the optimization technique.

  1. Fluoride in drinking water, brick tea infusion and human urine in two counties in Inner Mongolia, China.

    Science.gov (United States)

    Li, Hai-rong; Liu, Qing-bin; Wang, Wu-yi; Yang, Lin-sheng; Li, Yong-hua; Feng, Fu-jian; Zhao, Xiao-yu; Hou, Kun; Wang, Ge

    2009-08-15

    The objective of this study was to detect the fluoride level in the drinking water and the urine of habitants aged 16-55 years living in Inner Mongolia China. Furthermore, fluoride concentration of the brick tea infusion samples which were drunk by Mongolia herdsmen in everyday life living in SumuErga village of Ejin Horo Banner, Inner Mongolia China was also determined. A total of 117 participants (61 female and 56 male) were recruited from two counties for a cross-sectional study on health effects of chronic fluoride exposure from drinking water and drinking brick tea infusion. The fluoride concentration in drinking water, urine and brick tea infusion samples were determined using fluoride ion selective electrode method obtained from the Ministry of Health of the People's Republic of China. The average fluoride concentration in drinking water samples was 0.32+/-0.01 mg/L at AretengXire town of Ejin Horo Banner, 0.70+/-0.19 mg/L at SumuErga village of Ejin Horo Banner, and 2.68+/-1.15 mg/L at ZhalaiNuoer district of Manzhouli city. The average fluoride concentration in brick tea infusion samples which collected from Mongolia herdsmen at SumuErga village of Ejin Horo Banner was 1.81+/-1.09 mg/L. The average urinary fluoride concentration at AretengXire town of Ejin Horo Banner was 0.59+/-0.48 mg/L, at SumuErga village of Ejin Horo Banner was 1.45+/-0.93 mg/L and at ZhalaiNuoer district of Manzhouli city was 3.06+/-1.53 mg/L. The higher fluoride levels in the urine of participants may be associated to higher fluoride in drinking water at ZhalaiNuoer of Manzhouli city. However, drinking brick tea infusions with higher fluoride may be the cause of the higher fluoride contents in the Mongolia herdsmen's urine.

  2. Modifying Role of GSTP1 Polymorphism on the Association between Tea Fluoride Exposure and the Brick-Tea Type Fluorosis

    Science.gov (United States)

    Liu, Yang; Sun, Jing; Ye, Yan; Li, Bingyun; Liu, Xiaona; Liu, Hongxu; Sun, Zhenqi; Li, Mang; Cui, Jing; Sun, Dianjun; Yang, Yanmei; Gao, Yanhui

    2015-01-01

    Background Brick tea type fluorosis is a public health concern in the north-west area of China. The association between SNPs of genes influencing bone mass and fluorosis has attracted attention, but the association of SNPs with the risk of brick-tea type of fluorosis has not been reported. Objective To investigate the modifying roles of GSTP1 rs1695 polymorphisms on this association. Methods A cross-sectional study was conducted. Brick-tea water was tested by the standard of GB1996-2005 (China). Urinary fluoride was tested by the standard of WS/T 89-2006 (China). Skeletal fluorosis was diagnosed by X-ray, the part we scheduled was forearm, shank, and pelvic, then diagnosed the skeletal fluorosis by the standard of WS/192-2008 (China). Gene polymorphism was tested by Sequenom MassARRAY system. Result The prevalence rate in different ethnical participants was different: Tibetan individuals had the highest prevalence rate of skeletal fluorosis. There were significant differences in genotype frequencies of GSTP1 Rs1695 among different ethnical participants (pfluorosis (OR = 0.558 [95% CI, 0.326-0.955]). For Kazakh participants, a decreased risk of skeletal fluorosis among carriers of the G allele was limited to non high-loaded fluoride status (OR = 0. 166 [95% CI, 0.035–0.780] vs. OR = 1.478 [95% CI, 0.866–2.552] in participants with high-loaded fluoride status). Neither SNP-IF nor SNP-age for GSTP1 Rs1695 was observed. Conclusion The prevalence rate of the brick tea type fluorosis might have ethnic difference. For Tibetan individuals, who had the highest prevalence rate, G allele of GSTP1 Rs1695 might be a protective factor for brick tea type skeletal fluorosis. PMID:26046522

  3. Compressive strength of brick masonry made with weak mortars

    DEFF Research Database (Denmark)

    Pedersen, Erik Steen; Hansen, Klavs Feilberg

    2013-01-01

    The use of weak mortar has a number of advantages (e.g. prevention of expansion joints, environmental issues). However, according to EC6, the strength of masonry vanishes when the compressive strength of the mortar approaches zero. In reality the presence of even unhardened mortar kept in place...... (fm≈6 N/mm2) compression tests of masonry with perforated bricks show that the EC6 expression is not always safe for Danish masonry. This is probably because the tensile strength of the bricks also has an effect on the compressive strength of masonry when the mortar is stronger than weak lime mortar...

  4. Bayesian inference of the heat transfer properties of a wall using experimental data

    KAUST Repository

    Iglesias, Marco

    2016-01-06

    A hierarchical Bayesian inference method is developed to estimate the thermal resistance and volumetric heat capacity of a wall. We apply our methodology to a real case study where measurements are recorded each minute from two temperature probes and two heat flux sensors placed on both sides of a solid brick wall along a period of almost five days. We model the heat transfer through the wall by means of the one-dimensional heat equation with Dirichlet boundary conditions. The initial/boundary conditions for the temperature are approximated by piecewise linear functions. We assume that temperature and heat flux measurements have independent Gaussian noise and derive the joint likelihood of the wall parameters and the initial/boundary conditions. Under the model assumptions, the boundary conditions are marginalized analytically from the joint likelihood. ApproximatedGaussian posterior distributions for the wall parameters and the initial condition parameter are obtained using the Laplace method, after incorporating the available prior information. The information gain is estimated under different experimental setups, to determine the best allocation of resources.

  5. Purification of Single-walled Carbon Nanotubes Grown by a Chemical Vapour Deposition (CVD) Method

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A procedure for purification of single-walled carbon nanotubes(SWNTs) grown by the chemical vapour deposition (CVD) of carbon monooxide has been developed. Based on the result from TGA/DTA of as-prepared sample, the oxidation temperature was determined. The process included sonication, oxidation and acid washing steps. The purity and yield after purification were determined and estimated by TEM. Moreover, for the first time, a loop structure for CVD SWNTs has been observed.

  6. Method in calculating own vibration frequencies of open sections bars with thin walls

    Science.gov (United States)

    Mihuț, N.

    2016-08-01

    Dynamic stability of thin-walled bars of open sections, as well as the stability of elastic systems dynamics in general, is studying closely with their vibrations. This, because, areas of dynamics instability is around twice the frequency of free vibration of the bar or elastic system in all cases excitation parametric, on the one hand, and on the other hand matrices involved in the matrix equation of free vibration are matrices of matrix equation of dynamic stability. In this paper we settled differential equations of parametric vibrations of thin-walled straight bars open sections constant as a system with a triple infinity of second order differential equations, linear coefficients homogeneous and periodicals. In the end of work, by customizing differential equations of forced vibration parameters have been obtained differential equations of own vibration of bars with thin wall and open sections as a system with a triple infinity of differential equations of second order, linear, homogeneous with constant coefficients and, using it, the algebraic equation of own vibrations pulsations.

  7. A Fast Time-Delay Calculation Method in Through-Wall-Radar Detection Scenario

    Directory of Open Access Journals (Sweden)

    Zhang Qi

    2016-01-01

    Full Text Available In TWR (Through Wall Radar signal processing procedure, time delay estimation is one of the key steps in target localization and high resolution imaging. In time domain imaging procedure such as back projection imaging algorithm, round trip propagation time delay at the path of “transmitter-target-receiver” needs to be calculated for each pixel in imaging region. In typical TWR scenario, transmitter and receiver are at one side and targets at the other side of a wall. Based on two-dimensional searching algorithm or solving two variables equation of four times, traditional time delay calculation algorithms are complex and time consuming, and cannot be used to real-time imaging procedure. In this paper, a new fast time-delay (FTD algorithm is presented. Because of that incident angle at one side equals to refracting angle at the other side, an equation of lateral distance through the wall can be established. By solving this equation, the lateral distance can be obtained and total propagation time delay can be calculated subsequently. Through processing simulation data, the result shows that new algorithm can be applied effectively to real-time time-delay calculation in TWR signal processing.

  8. Utilisation of IGCC slag and clay steriles in soft mud bricks (by pressing) for use in building bricks manufacturing.

    Science.gov (United States)

    Acosta, A; Iglesias, I; Aineto, M; Romero, M; Rincón, J Ma

    2002-01-01

    The subject of this study is the application to the construction of soft mud bricks (also known as pressed bricks), both green and heat-treated bodies, built from raw materials from Santa Cruz de Mudela, Ciudad Real, and IGCC slag from the power central of Puertollano (Ciudad Real, Spain). For this purpose, industrial level tests have been performed: the production of these kind of bricks from mixes of waste from ores of construction clays and to significant fraction of different ratios and clay granulometries mixed with IGCC slag. The results of this experimentation suggests that not only can IGCC slag be applied to a ceramic process, but also its use gives several advantages, as water and energy savings, as well as improvements on the final properties of products.

  9. An Investigation of Shear Wall of Moen-Jo-Daro Using Mechanical Properties

    Directory of Open Access Journals (Sweden)

    Shazada Muhammad Umair Khan

    2014-05-01

    Full Text Available This investigation is based on the event that occur in 2000 and 2012 at Moen-Jo-Daro the extensive decay of Moen-Jo-Daro wall that replacement of bricks with new over damaged bricks. Damaged bricks due to the formation of various generated forces, continutiy of thrust resulted in the progressive instability of the lateral wall and formation of minor and major cracks. There are several walls which are facing similar problem, hence, a cubical clay model in 1/4-scale was built and investegated under service conditions. Finite-element FE, Models were generated to simulate the response of the structure, behaviour and safety of the prototype.

  10. Evaluation of the Efficiency of Different Disruption Methods on Yeast Cell Wall Preparation for β-Glucan Isolation

    Directory of Open Access Journals (Sweden)

    Anna Bzducha-Wróbel

    2014-12-01

    Full Text Available Selected methods for yeast cell disruption were evaluated to establish their suitability for cell wall preparation in the process of β-glucan isolation. The effect of different disruption methods on contents of total saccharides, β-glucans and proteins in the produced cell walls preparations was analyzed. The degree of cell wall purification from intracellular components was established on the basis of the ratio of solubilised material. The investigated methods included: cell exposure to hot water (autoclaving, thermally-induced autolysis, homogenization in a bead mill, sonication and their combinations. Experimental systems were prepared in water (pH 5.0 and pH 7.0 and Tris-HCl buffer (pH 8.0. The Saccharomyces cerevisiae yeast cell wall preparations with the highest degree of cytosol component release and purification of β-glucans were produced by 30 min of cell homogenization with zirconium-glass beads (0.5 mm in diameter. This was confirmed by the highest ratio of solubilised material (approx. 64%–67%. The thus-produced preparations contained ca. 60% of total saccharides, 13%–14% of β(1,3/(1,6-glucans, and approx. 35% of crude proteins. Similar results were obtained after autolysis coupled with bead milling as well as with sonication, but the time required for these processes was more than 24 h. Homogenization in a bead mill could be valuable for general isolation procedures because allows one to eliminate the different autolytic activity of various yeast strains.

  11. Wind Load Test of Earthbag Wall

    Directory of Open Access Journals (Sweden)

    Ryan Scott

    2013-08-01

    Full Text Available Earthbag construction is a sustainable, low-cost, housing option for developing countries. Earthbag structures are built of individual soil-filled fabric bags (i.e., sand bags stacked in a running bond pattern. Once stacked, earthbags are compacted and the soil inside the bags is dried in-place to form earthen bricks. Barbed wires are placed between each course to affect shear transfer within the wall. Results of an out-of-plane load test on a full-scale earthbag wall are presented in this paper. The wall was subjected to out-of-plane pressure up to 3.16 kPa, which resulted in plastic deformations up to 50 mm. The wall did not collapse during loading. Wall behavior and force transfer mechanisms are discussed.

  12. Investigation of thermal effect on exterior wall surface of building material at urban city area

    Directory of Open Access Journals (Sweden)

    Mohd Fadhil Md Din, Hazlini Dzinun, M. Ponraj, Shreeshivadasan Chelliapan, Zainura Zainun Noor, Dilshah Remaz, Kenzo Iwao

    2012-01-01

    Full Text Available This paper describes the investigation of heat impact on the vertical surfaces of buildings based on their thermal behavior. The study was performed based on four building materials that is commonly used in Malaysia; brick, concrete, granite and white concrete tiles. The thermal performances on the building materials were investigated using a surface temperature sensor, data logging system and infrared thermography. Results showed that the brick had the capability to absorb and store heat greater than other materials during the investigation period. The normalized heat (total heat/solar radiation of the brick was 0.093 and produces high heat (51% compared to granite, confirming a substantial amount of heat being released into the atmosphere through radiation and convection. The most sensitive material that absorbs and stores heat was in the following order: brick > concrete > granite > white concrete tiles. It was concluded that the type of exterior wall material used in buildings had significant impact to the environment.

  13. Investigation of thermal effect on exterior wall surface of building material at urban city area

    Energy Technology Data Exchange (ETDEWEB)

    Md Din, Mohd Fadhil; Dzinun, Hazlini; Ponraj, M.; Chelliapan, Shreeshivadasan; Noor, Zainura Zainun [Institute of Environmental Water Resources and Management (IPASA), Faculty of Civil Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor (Malaysia); Remaz, Dilshah [Faculty of Built Environment, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor (Malaysia); Iwao, Kenzo [Nagoya Institute of Technology, Nagoya (Japan)

    2012-07-01

    This paper describes the investigation of heat impact on the vertical surfaces of buildings based on their thermal behavior. The study was performed based on four building materials that is commonly used in Malaysia; brick, concrete, granite and white concrete tiles. The thermal performances on the building materials were investigated using a surface temperature sensor, data logging system and infrared thermography. Results showed that the brick had the capability to absorb and store heat greater than other materials during the investigation period. The normalized heat (total heat/solar radiation) of the brick was 0.093 and produces high heat (51% compared to granite), confirming a substantial amount of heat being released into the atmosphere through radiation and convection. The most sensitive material that absorbs and stores heat was in the following order: brick > concrete > granite > white concrete tiles. It was concluded that the type of exterior wall material used in buildings had significant impact to the environment.

  14. A comparison between thermographic and flow-meter methods for the evaluation of thermal transmittance of different wall constructions

    Science.gov (United States)

    Nardi, I.; Ambrosini, D.; de Rubeis, T.; Sfarra, S.; Perilli, S.; Pasqualoni, G.

    2015-11-01

    One of the key parameters that “meter” the energy performance of the whole structure of buildings is the thermal transmittance. This parameter can be evaluated with a theoretical approach, regulated by standard ISO 6946, once the stratigraphy of the envelope and the properties of the constituent materials are known, or by using a heat flow meter (HFM), following the recommendations provided in standard ISO 9869. Recently, the use of quantitative IR Thermography (IRT) has been proposed by several researchers; this method allows to determine the overall transmittance of an envelope in a short time (especially in comparison with HFM method). However, the theoretical or experimental transmittance, measured on real buildings having walls composed by different materials, can be rather distant from those calculated or measured with different procedures. For this reason, for a correct certification of the thermal performance of a building envelope, it is necessary the availability of experimental procedures for a direct and reliable evaluation of the thermal transmittance, suitable for different walls. Research has found that, especially in historical constructions, faults in the building envelope and the age of the materials can greatly affect the HFM measurements. The aim of this work is to analyze in situ the thermal performance of three different walls which have been selected according to: different materials, different age, and different construction. On each envelope, a comparison between U-values, measured by HFM and IRT, and computed according the standard procedure, has been effected.

  15. THE ANALYSIS OF THIN WALLED COMPOSITE LAMINATED HELICOPTER ROTOR WITH HIERARCHICAL WARPING FUNCTIONS AND FINITE ELEMENT METHOD

    Institute of Scientific and Technical Information of China (English)

    诸德超; 邓忠民; 王荇卫

    2001-01-01

    In the present paper, a series of hierarchical warping functions is developed to analyze the static and dynamic problems of thin walled composite laminated helicopter rotors composed of several layers with single closed cell. This ethod is the development and extension of the traditional constrained warping theory of thin walled metallic beams, which had been proved very successful since 1940s. The warping distribution along the perimeter of each layer is expanded into a series of successively corrective warping functions with the traditional warping function caused by free torsion or free bending as the first term, and is assumed to be piecewise linear along the thickness direction of layers. The governing equations are derived based upon the variational principle of minimum potential energy for static analysis and Rayleigh Quotient for free vibration analysis. Then the hierarchical finite element method is introduced to form a numerical algorithm. Both static and natural vibration problems of sample box beams are analyzed with the present method to show the main mechanical behavior of the thin walled composite laminated helicopter rotor.

  16. Research on basic mechanical properties of autoclaved fly ash brick%蒸压粉煤灰砖基本力学性能研究

    Institute of Scientific and Technical Information of China (English)

    刘双龙; 闫欢欢

    2011-01-01

    按照《砌墙砖试验方法》(GB/T2542-2003)对蒸压粉煤灰砖进行砖的含水率、抗压强度、抗折强度试验。确定蒸压粉煤灰砖的基本力学指标,为编制辽宁省地方标准《蒸压粉煤灰砖建筑技术规范》提供试验依据。结果表明,蒸压粉煤灰砖含水率为2.96%,抗压强度为11.46MPa,抗折强度为1.68MPa,在实际工程上可替代普通烧结砖使用。%According to the GB/T 2542-2003 of masonry brick test method,the moisture content,compressive strength,transverse strength of the autoclaved fly ash brick are test.The results show that the autoclaved fly ash brick moisture content is 2.96 %,the compressive strength is 11.46 MPa,and the transverse strength is 1.68 MPa,so it can used as a substitute for the common fired brick in project.The mechanics index can provide a basis for the Liaoning standards of fly ash brick construction technical specifications.

  17. Restoration of abdominal wall integrity as a salvage procedure in difficult recurrent abdominal wall hernias using a method of wide myofascial release.

    Science.gov (United States)

    Levine, J P; Karp, N S

    2001-03-01

    The management of primary and recurrent giant incisional hernias remains a complex and frustrating challenge even with multiple alloplastic and autogenous closure options. The purpose of this study was to develop a reconstructive technique of restoring abdominal wall integrity to a subcategory of patients, who have failed initial hernia therapy, by performing superior and lateral myofascial release. Over a 1.5-year period, 10 patients with previously unsuccessful treatment of abdominal wall hernias, using either primary repair or placement of synthetic material, were studied. The patients had either recurrence of the hernia or complications such as infections requiring removal of synthetic material. The hernias were not able to be treated with standard primary closure techniques or synthetic material. The average defect size was 19 x 9 cm. Each patient underwent wide lysis of bowel adhesions releasing the posterior abdominal wall fascia to the posterior axillary line, subcutaneous release of the anterior abdominal wall fascia to a similar level, and complete removal of any synthetic material (if present). The abdominal domain was reestablished by releasing the laterally retracted abdominal wall. The amount of available abdominal wall tissue was increased by wide release of the cephalic abdominal wall fascia overlying the costal margin and the external oblique fascia and muscle laterally. If needed, partial thickness of the internal oblique muscle and its anterior fascia were also released laterally to perform a tension-free primary closure of the defect. All repairs were closed with satisfactory functional and aesthetic results. All alloplastic material was removed. Fascial release was limited so as to close only the hernia defect without tension. No significant release of the rectus sheath and muscle was needed. Good, dynamic muscle function was noted postoperatively. All repairs have remained intact, and no further abdominal wall hernias have been noted on follow-up.

  18. Numerical simulation of wave impact on a rigid wall using a two--phase compressible SPH method

    CERN Document Server

    Rafiee, Ashkan; Dias, Frédéric

    2013-01-01

    In this paper, an SPH method based on the SPH--ALE formulation is used for modelling two-phase flows with large density ratios and realistic sound speeds. The SPH scheme is further improved to circumvent the tensile instability that may occur in the SPH simulations. The two-phase SPH solver is then used to model a benchmark problem of liquid impact on a rigid wall. The results are compared with an incompressible Level Set solver. Furthermore, a wave impact on a rigid wall with a large entrained air pocket is modelled. The SPH simulation is initialised by the output of a fully non-linear potential flow solver. The pressure distribution, velocity field and impact pressure are then analysed.

  19. Instrumented thick-walled tube method for measuring thermal pressure in fluids and isotropic stresses in thermosetting resins

    Science.gov (United States)

    Merzlyakov, Mikhail; Simon, Sindee L.; McKenna, Gregory B.

    2005-06-01

    We have developed a method for measuring the thermal pressure coefficient and cure-induced and thermally induced stresses based on an instrumented thick-walled tube vessel. The device has been demonstrated at pressures up to 330 MPa and temperatures to 300 °C. The method uses a sealed stainless steel thick-walled tube to impose three-dimensional isotropic constraints. The tube is instrumented with strain gauges in hoop and in axial directions and can be used in open or closed configurations. By making measurements of the isotropic stresses as a function of temperature, the method allows determination of the thermal pressure coefficient in both the glassy and rubbery (or liquid) states. The method also can be used to measure isotropic stress development in thermosetting resins during cure and subsequent thermal cycling. Experimental results are presented for sucrose benzoate, di-2-ethylhexylsebacate, and an epoxy resin. The current report shows that the method provides reliable estimates for the thermal pressure coefficient. The thermal pressure coefficient is determined with resolution on the order of 10kPa/K. Among advantages of the method is that the tubes are reusable, even when measurements are made for cure response of thermosetting resins.

  20. Improved electroless plating method through ultrasonic spray atomization for depositing silver nanoparticles on multi-walled carbon nanotubes

    Science.gov (United States)

    Zhao, Qi; Xie, Ming; Liu, Yichun; Yi, Jianhong

    2017-07-01

    A novel method was developed to deposit nanosized silver particles on multi-walled carbon nanotubes (MWCNTs). The electroless plating of silver on MWCNTs accomplished in small solution drops generated by ultrasonic spray atomization, which inhibited excessive growth of silver particles and led to much more uniform nanometer grain-sized coatings. The results showed that pretreatment was essential for silver particles to deposit on the MWCNTs, and the electrolyte concentration and reaction temperature were important parameters which had a great influence on the morphology and structure of the silver coatings. Possible mechanisms of this method are also discussed in the paper.

  1. A New Method for the Adaptive Control of Vortex-Wall Interactions

    Science.gov (United States)

    Koumoutsakos, P.

    1996-01-01

    The control of vortical flows is gaining significance in the design of aeronautical and marine structures. While passive devices have been used effectively in the past, active control strategies have the potential of allowing a leap in the performance of future configurations. The efficiency of control schemes is strongly dependent on the development of accurate flow models that can be devised using information that is available not only from numerical solutions of the governing Navier-Stokes equations but also can be measured experimentally. In that context it is desirable to construct adaptive control schemes using information that can be measured at the wall.

  2. Effects of using arsenic-iron sludge wastes in brick making.

    Science.gov (United States)

    Hassan, Khondoker Mahbub; Fukushi, Kensuke; Turikuzzaman, Kazi; Moniruzzaman, S M

    2014-06-01

    The arsenic-iron sludge generated in most of the treatment systems around the world is discharged into the nearest watercourse, which leads to accumulative rise of arsenic and iron concentrations in water. In this study, attempts were made to use the arsenic-iron sludge in making bricks and to analyze the corresponding effects on brick properties. The water treatment plant sludge is extremely close to brick clay in chemical composition. So, the sludge could be a potential substitute for brick clay. This study involved the addition of sludge with ratios 3%, 6%, 9% and 12% of the total weight of sludge-clay mixture. The physical and chemical properties of the produced bricks were then determined and evaluated and compared to control brick made entirely from clay. Results of different tests indicated that the sludge proportion and firing temperature were the two key factors in determining the quality of bricks. The compressive strength of 3%, 6%, 9% and 12% sludge containing brick samples were found to be 14.1 MPa, 15.1 MPa, 9.4 MPa and 7.1 MPa, respectively. These results indicate that the compressive strength of prepared bricks initially increased and then decreased with the increase of sludge proportion. Leaching characteristics of burnt bricks were determined with the variation of pH at a constant temperature. The optimum amount of sludge that could be mixed with clay to produce good bonding of clay-sludge bricks was found to be 6% (safely maximum) by weight.

  3. Do Schools Still Need Brick-and-Mortar Libraries?

    Science.gov (United States)

    Johnson, Doug; Mastrion, Keith

    2009-01-01

    Do all schools need brick-and-mortar libraries? In this article, Johnson and Mastrion share their contradictory thoughts to the question. Johnson says some schools don't need library facilities or programs or librarians. These schools' teachers and administrators: (1) feel no need for a collaborative learning space; (2) feel the ability to process…

  4. Effects of water on mortar-brick bond

    NARCIS (Netherlands)

    Groot, C.J.W.P.

    1995-01-01

    The quality of bond in masonry is, to a large extent, a function of the (i) the hydration conditions and (ii) the mortar composition of the mortar-brick interface. For insight into the effects of these parameters on bond performance it is essential to dispose of quantitative information about water

  5. Effects of waste glass additions on quality of textile sludge-based bricks.

    Science.gov (United States)

    Rahman, Ari; Urabe, Takeo; Kishimoto, Naoyuki; Mizuhara, Shinji

    2015-01-01

    This research investigated the utilization of textile sludge as a substitute for clay in brick production. The addition of textile sludge to a brick specimen enhanced its pores, thus reducing the quality of the product. However, the addition of waste glass to brick production materials improved the quality of the brick in terms of both compressive strength and water absorption. Maximum compressive strength was observed with the following composition of waste materials: 30% textile sludge, 60% clay and 10% waste glass. The melting of waste glass clogged up pores on the brick, which improved water absorption performance and compressive strength. Moreover, a leaching test on a sludge-based brick to which 10% waste glass did not detect significant heavy metal compounds in leachates, with the product being in conformance with standard regulations. The recycling of textile sludge for brick production, when combined with waste glass additions, may thus be promising in terms of both product quality and environmental aspects.

  6. Study on Microstructure and Slag Corrosion Mechanism of High Chrome Bricks for Gasifier

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Research was focused on slag corrosion mechanism of high chrome bricks used for different types of gasifier by comparing the structure of high chrome bricks for petroleum coke gasifier and water-coal slurry gasifier with slag corroded testing brick and water coal slurry gasifier through Scanning Electron Microscope (SEM) examination and X-ray diffraction. Results show that for high chrome brick used for petroleum coke gasifier, corrosion is mainly caused by Cr2O3 in the brick and V2O5 in molten slag and liquid phase generation at low temperature; for high chrome brick used for water-coal slurry gasifier, corrosion is caused by dissolution of Cr2O3 in molten slag and corrosion of ZrO2. For LIRR-HK95 brick, it performs better petroleum coke corrosion resistance than the others due to the optimal composition and structure.

  7. Prevalence of work-related musculoskeletal disorders among the brick field workers of West Bengal, India.

    Science.gov (United States)

    Das, Banibrata

    2014-01-01

    Brick field industry is one of the most important and oldest industries in India, where millions of workers suffered from work-related musculoskeletal disorders (WMSDs). The main aim of the present investigation was to assess the prevalence of WMSDs among brick field workers. A cross-sectional study was conducted on 216 brick field workers. A modified Nordic questionnaire was applied among them. In brick making industry, the workers adopt different unfavorable actions, such as frequent bending; bending and twisting of the body; and working above shoulder height, which may lead to severe pain in different parts of the body, especially lower back (brick carriers: 90%; moulders: 92%; fireman: 75%; stackers: 88%) and neck (brick carriers: 89%; moulders: 88%; fireman: 54%; stackers: 72%), It was concluded from the study that health of the brick field workers was highly affected due to working in different awkward postures for long periods.

  8. Influence of pH during chemical weathering of bricks: Long term exposure

    DEFF Research Database (Denmark)

    Rörig-Dalgaard, Inge; Charola, A. Elena

    2016-01-01

    Within the framework of environmental weathering of bricks in historical structures, this study focuses on new bricks currently employed for restoration projects. The bricks were subjected to an accelerated chemical weathering test by immersion in solutions with pH ranging from 3 to 13 for differ......Within the framework of environmental weathering of bricks in historical structures, this study focuses on new bricks currently employed for restoration projects. The bricks were subjected to an accelerated chemical weathering test by immersion in solutions with pH ranging from 3 to 13...... for different lengths of time up to 432 days, data to 288 days are presented since the project is still ongoing. The study analyzed the changes of pH induced in the solutions by the presence of the bricks (this also served to adjust the pH to the intended value), as well as the concentration of various ions...

  9. Dynamic thermal performance of alveolar brick construction system

    Energy Technology Data Exchange (ETDEWEB)

    Gracia, A. de; Castell, A.; Medrano, M. [GREA Innovacio Concurrent, Edifici CREA, Universitat de Lleida, Pere de Cabrera s/n, 25001 Lleida (Spain); Cabeza, L.F., E-mail: lcabeza@diei.udl.ca [GREA Innovacio Concurrent, Edifici CREA, Universitat de Lleida, Pere de Cabrera s/n, 25001 Lleida (Spain)

    2011-07-15

    Highlights: {yields} Even though U-value does not measure thermal inertia, it is the commonly used parameter. {yields} The thermal performance analysis of buildings must include the evaluation of transient parameters. {yields} Transient parameters of alveolar brick constructive system show good agreement with its low energy consumption. -- Abstract: Alveolar bricks are being introduced in building sector due to the simplicity of their construction system and to the elimination of the insulation material. Nevertheless, it is not clear if this new system is energetically efficient and which is its thermal behaviour. This paper presents an experimental and theoretical study to evaluate the thermal behaviour of the alveolar brick construction system, compared with a traditional Mediterranean brick system with insulation. The experimental study consists of measuring the thermal performance of four real house-like cubicles. The thermal transmittance in steady-state, also known as U-value, is calculated theoretically and experimentally for each cubicle, presenting the insulated cubicles as the best construction system, with differences around 45% in comparison to the alveolar one. On the other hand, experimental results show significantly smaller differences on the energy consumption between the alveolar and insulated construction systems during summer period (around 13% higher for the alveolar cubicle). These values demonstrate the high thermal efficiency of the alveolar system. In addition, the lack of agreement between the measured energy consumption and the calculated U-values, guides the authors to analyze the thermal inertia of the different building components. Therefore, several transient parameters, extracted from the heat transfer matrix and from experimental data, are also evaluated. It can be concluded that the alveolar brick construction system presents higher thermal inertia than the insulated one, justifying the low measured energy consumption.

  10. Change Mechanism in Property and Microstruture of Magnesite—chrome Brick for Use in Super H—T Tunnel Kiln

    Institute of Scientific and Technical Information of China (English)

    SHAOYang; SUNJu; 等

    1998-01-01

    On the basis of determination of property and microstructure of two kinds of primary MgO-Cr2O3 bricks and residual magnesite-chrome bricks for super H-T tunnel kiln,combining with the both residul bricks's application result,the paper expounds the change mechanism of the two kinds of magnesite-chrome bricks during the operation period,especially stresses the advantages of low Cr2O3 MgO-Cr2O3 bricks.

  11. An efficient method for the carboxylation of few-wall carbon nanotubes with little damage to their sidewalls

    Energy Technology Data Exchange (ETDEWEB)

    Martín, Olga [Department of Materials Science and Engineering and Chemical Engineering, Universidad Carlos III de Madrid, Av. Universidad 30, 28911 Leganés-Madrid (Spain); Gutierrez, Humberto R. [Department of Physics and Astronomy, 102 Natural Science Building, University of Louisville, Louisville, KY 40292 (United States); Maroto-Valiente, Angel [Departamento de Química Inorgánica y Química Técnica, Facultad de Ciencias, UNED, C/ Senda del Rey 9, 28040 Madrid (Spain); Terrones, Mauricio [Research Center for Exotic Nanocarbons (JST), Shinshu University, Wakasato 4-17-1, Nagano 380-8553 (Japan); Department of Physics, Department of Materials Science and Engineering and Materials Research Institute, The Pennsylvania State University, 104 Davey Lab., University Park, PA 16802-6300 (United States); Blanco, Tamara [Materials and Processes Department, Airbus Operations S.L., Paseo John Lennon s/n, 28906 Getafe-Madrid (Spain); Baselga, Juan, E-mail: jbaselga@ing.uc3m.es [Department of Materials Science and Engineering and Chemical Engineering, Universidad Carlos III de Madrid, Av. Universidad 30, 28911 Leganés-Madrid (Spain)

    2013-07-15

    We report a novel method that is able to efficiently functionalize carbon nanotubes (few-walled: from 1 to 6 layers and multiwalled) with a high yield of carboxyl groups, based on treatments with H{sub 2}O{sub 2} in the presence of UV light. The amount of carboxylic groups was quantified by X-ray photoelectron spectroscopy and back-titration, showing both measurements reasonable agreement. According to the zeta potential values and to the amount of suspended nanotubes, we demonstrate that the method is able to produce uniform and stable suspensions of carbon nanotubes in water. With the aid of scanning and transmission electron microscopy, thermogravimetric analysis, and Raman spectroscopy, we show that the surfaces of the tubes are not damaged by the treatment and that the functionalized tubes have an enhanced reactivity toward oxygen. This route is efficient and could now be used to fabricate polymer composites using few-walled and multiwalled carbon nanotubes. - Highlights: • We report an efficient method for acid functionalization of carbon nanotubes. • The method produces uniform and stable suspensions of carbon nanotubes in water. • The surfaces of the tubes are not damaged by the treatment.

  12. Modelling 3D crack propagation in ageing graphite bricks of Advanced Gas-cooled Reactor power plant

    Directory of Open Access Journals (Sweden)

    Thi-Tuyet-Giang Vo

    2015-10-01

    Full Text Available In this paper, crack propagation in Advanced Gas-cooled Reactor (AGR graphite bricks with ageing properties is studied using the eXtended Finite Element Method (X-FEM. A parametric study for crack propagation, including the influence of different initial crack shapes and propagation criteria, is conducted. The results obtained in the benchmark study show that the crack paths from X-FEM are similar to the experimental ones. The accuracy of the strain energy release rate computation in a heterogeneous material is also evaluated using a finite difference approach. Planar and non-planar 3D crack growth simulations are presented to demonstrate the robustness and the versatility of the method utilized. Finally, this work contributes to the better understanding of crack propagation behaviour in AGR graphite bricks and so contributes to the extension of the AGR plants’ lifetimes in the UK by reducing uncertainties.

  13. Numerical simulations of tests masonry walls from ceramic block using a detailed finite element model

    Directory of Open Access Journals (Sweden)

    V. Salajka

    2017-01-01

    Full Text Available This article deals with an analysis of the behaviour of brick ceramic walls. The behaviour of the walls was analysed experimentally in order to obtain their bearing capacity under static loading and their seismic resistance. Simultaneously, numerical simulations of the experiments were carried out in order to obtain additional information on the behaviour of masonry walls made of ceramic blocks. The results of the geometrically and materially nonlinear computations were compared to the results of the performed tests.

  14. Nitric acid treated multi-walled carbon nanotubes optimized by Taguchi method

    Science.gov (United States)

    Shamsuddin, Shahidah Arina; Derman, Mohd Nazree; Hashim, Uda; Kashif, Muhammad; Adam, Tijjani; Halim, Nur Hamidah Abdul; Tahir, Muhammad Faheem Mohd

    2016-07-01

    Electron transfer rate (ETR) of CNTs can be enhanced by increasing the amounts of COOH groups to their wall and opened tips. With the aim to achieve the highest production amount of COOH, Taguchi robust design has been used for the first time to optimize the surface modification of MWCNTs by nitric acid oxidation. Three main oxidation parameters which are concentration of acid, treatment temperature and treatment time have been selected as the control factors that will be optimized. The amounts of COOH produced are measured by using FTIR spectroscopy through the absorbance intensity. From the analysis, we found that acid concentration and treatment time had the most important influence on the production of COOH. Meanwhile, the treatment temperature will only give intermediate effect. The optimum amount of COOH can be achieved with the treatment by 8.0 M concentration of nitric acid at 120 °C for 2 hour.

  15. Evaluation of Wall Boundary Conditions for Impedance Eduction Using a Dual-Source Method

    Science.gov (United States)

    Watson, W. R.; Jones, M. G.

    2012-01-01

    The accuracy of the Ingard-Myers boundary condition and a recently proposed modified Ingard-Myers boundary condition is evaluated for use in impedance eduction under the assumption of uniform mean flow. The evaluation is performed at three centerline Mach numbers, using data acquired in a grazing flow impedance tube, using both upstream and downstream propagating sound sources, and on a database of test liners for which the expected behavior of the impedance spectra is known. The test liners are a hard-wall insert consisting of 12.6 mm thick aluminum, a linear liner without a facesheet consisting of a number of small diameter but long cylindrical channels embedded in a ceramic material, and two conventional nonlinear liners consisting of a perforated facesheet bonded to a honeycomb core. The study is restricted to a frequency range for which only plane waves are cut on in the hard-wall sections of the flow impedance tube. The metrics used to evaluate each boundary condition are 1) how well it educes the same impedance for upstream and downstream propagating sources, and 2) how well it predicts the expected behavior of the impedance spectra over the Mach number range. The primary conclusions of the study are that the same impedance is educed for upstream and downstream propagating sources except at the highest Mach number, that an effective impedance based on both the upstream and downstream measurements is more accurate than an impedance based on the upstream or downstream data alone, and that the Ingard-Myers boundary condition with an effective impedance produces results similar to that achieved with the modified Ingard-Myers boundary condition.

  16. Antioxidant enzymes status and reproductive health of adult male workers exposed to brick kiln pollutants in Pakistan.

    Science.gov (United States)

    Jahan, Sarwat; Falah, Samreen; Ullah, Hizb; Ullah, Asad; Rauf, Naveed

    2016-07-01

    The present study was designed to study the effect of brick kilns emissions on the reproductive health and biochemical status of brick kiln workers and people living in the area near brick kilns. Body mass index (BMI) was significantly reduced in brick makers, carriers, and bakers compared to the control. Red blood cells count and hematocrit (%) were significantly high in brick bakers while MCH was significantly reduced in brick makers and brick bakers. Heavy metals (lead, cadmium, and chromium) concentration in whole blood of the brick kiln workers were significantly higher as compared to the control. Antioxidant enzymes (CAT, SOD, POD, GSH, and GR) were significantly reduced in brick kiln workers as compared to the control while TBARS level were significantly high in brick bakers as compared to the control. Plasma leutinizing hormone (LH) was significantly high in brick bakers while testosterone concentrations were significantly reduced in brick makers, carriers, and bakers. The present study shows that brick kiln workers and people living in the brick kiln vicinity are exposed to heavy metals and other pollutants that is a serious threat to their health. Alternate technology is needed to be developed and brick kilns should be replaced.

  17. IMPROVED LOCALLY CONFORMAL FINITE-DIFFERENCE TIME-DOMAIN METHOD FOR EDGE INCLINED SLOTS IN A FINITE WALL THICKNESS WAVEGUIDE

    Institute of Scientific and Technical Information of China (English)

    Li Long; Zhang Yu; Liang Changhong

    2004-01-01

    An Improved Locally Conformal Finite-Difference Time-Domain (ILC-FDTD) method is presented in this paper, which is used to analyze the edge inclined slots penetrating adjacent broadwalls of a finite wall thickness waveguide. ILC-FDTD not only removes the instability of the original locally conformal FDTD algorithm, but also improves the computational accuracy by locally modifying magnetic field update equations and the virtual iterative electric fields according to the complexity of the slot fringe fields. The mutual coupling between two edge inclined slots can also be analyzed by ILC-FDTD effectively.

  18. A Numerical-analytic Method for Quickly Predicting Springback of Numerical Control Bending of Thin-walled Tube

    Institute of Scientific and Technical Information of China (English)

    Mei ZHAN; He YANG; Liang HUANG

    2006-01-01

    Springback is one of important factors influencing the forming quality of. numerical control(NC)bending of thin-walled tube. In this paper, a numerical-analytic method for springback angle prediction of the process was put forward. The method is based on springback angle model derived using analytic method and simulation results from three-dimensional(3D)rigid-plastic finite element method(FEM). The method is validated through comparison with experimental results. The features of the method are as follows:(1)The method is high in efficiency because it combines advantages of rigid-plastic FEM and analytic method.(2)The method is satisfactory in accuracy, since the field variables used in the model is resulting from 3D rigid-plastic FEM solution, and the effects both of axial force and strain neutral axis shift have been included.(3)Research on multi-factor effects can be carried out using the method due to its advantage inheriting from rigid-plastic FEM. The method described here is also of general significance to other bending processes.

  19. Numerical analysis of the jet stage of bubble near a solid wall using a front tracking method

    Science.gov (United States)

    Liu, L. T.; Yao, X. L.; Zhang, A. M.; Chen, Y. Y.

    2017-01-01

    The dynamics of a toroidal bubble near a solid wall for a large part of stand-off parameters γ (γ=d/Rmax, d is the distance between the solid wall and the bubble centre at the moment of formation and Rmax is the maximum bubble radius) have been extensively studied, but some mechanics of a toroidal bubble are not completely clear, especially for the small stand-off parameters γ ≤ 0.8. In the present study, on the basis of the finite volume method, the Navier-Stokes equations with inviscid and incompressible assumption are directly solved using a staggered grid on the fixed grid. The dynamics of the toroidal bubble near the solid for different stand-off parameters (γ = 0.4, 0.6, 0.8, and 0.97, respectively) are simulated by a front tracking method. Initial conditions of numerical simulation are estimated through the Rayleigh-Plesset equation, based on the maximum size and collapse time of a spark-generated bubble. One of the numerical results is compared with a spark-generated bubble experiment, showing that the results between them are favorable with regard to both the bubble shape history and translational motion of the bubble. The numerical results for the different stand-off parameters, including the change process of the water layer, the development process of the splash flow and radial flow, the splitting phenomenon of the toroidal bubble, and the trend of pressure on the center of the solid wall, are discussed, where some new phenomena are discovered.

  20. Simplified architectural method for the solar control optimization of awnings and external walls in houses in hot and dry climates

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Munoz, V.M. [Instituto Politecnico Nacional, Mexico City (Mexico). Centro Interdisciplinario de Ciencias Marinas; Porta-Gandara, M.A. [Centro de Investigaciones Biologicas del Noroeste, Mexico City (Mexico)

    2003-01-01

    In extremely hot and dry climates, like northwestern Mexico, solar gain reduction in houses using solar passive techniques is important for improving comfort inside the construction and to save costs in electrical cooling during the whole year, because the winter season is also hot in those regions. A new one-dimension method is proposed to analyze the interaction between two common shading devices: awnings and external walls to reduce insulation on the facade and inside the house due to fenestration. The method is demonstrated by optimizing a typical dwelling with an azimuth of 90{sup o} (east), which, achieves 45% reduction in direct solar insulation during the summer solstice on the profile of the facade. Results showed that this method is simple and reliable in increasing the shadow on the facade and to block completely the solar beam radiation on the windowpane with optimal relations between these shading devices. (author)

  1. Surface Water Quality Assessment of the Jirania Brick Cluster – A Case Study

    Directory of Open Access Journals (Sweden)

    Amarendra Jamatia

    2014-06-01

    Full Text Available Along with the infrastructural development works, the demand for construction materials is increasing rapidly, which in turns lead to the rapid growth of brick manufacturing industries. Large demand of bricks in development and construction sectors has resulted in mushrooming of brick industries clusters at the outskirt of Agartala City. Jirania brick industries cluster is one of largest cluster of the Tripura State (India. Approximately 45% of total bricks of the State are being produced from the Jirania brick industries clusters. The use of conventional technology for brick making has resulted significant contribution of pollution load to the environment. The main components of environment which are being affected by the brick industries include but not limited to air, water, soil etc. The present study is carried out to identify the potential contribution of pollution load on surface water sources of the region from the mentioned brick industries. The surface water samples collected from nine sampling station located at different places in the area are analyzed and the experimental results of various quality parameters are presented in the paper. Such a study will help to estimate the total pollution load of the brick industry in the mentioned area.

  2. Utilisation of Sepidrud dam basin sediments in fired clay bricks: laboratory scale experiment

    Directory of Open Access Journals (Sweden)

    Jamshidi-Chenari, R.

    2015-12-01

    Full Text Available The prevailing disposal methods for dam basin sediments are not free from the environmental pollution and the ecological imbalance. At present, a new way to treat the dredged sediments to manufacture bricks is being investigated, prioritizing waste recovery over its deposition in landfills. However, construction materials such as clay bricks must comply with the international and local standards. Considering the perpetual availability of the sediments, particle sizing and their chemical composition and the results of physical and qualification tests on Sepidrud Dam basin sediments it can be concluded that the utilization of basin sediments as a full or partial replacement in clay brick production will lead to the production of quality bricks that meet all the regulatory limits in the standards. This research is novel in view of both increasing the reservoir effective volume capacity and preventing the use of alternative land quarries which are mainly covered by green land.Los métodos actuales de eliminación de los sedimentos de las cuencas de las presas no están exentos de problemas de contaminación ambiental y ecológicos. En la actualidad, se está investigando la posibilidad de utilizar los sedimentos dragados para la fabricación de ladrillos, dando prioridad a su valoración como residuos frente a su depósito en vertederos. Sin embargo, los ladrillos, como otros materiales de construcción, deben de cumplir con las correspondientes normas nacionales e internacionales. Teniendo en cuenta la disponibilidad permanente de los sedimentos, el tamaño de sus partículas y su composición química y los resultados físicos de las pruebas de calificación de los sedimentos de la cuenca Sepidrud Dam, en este estudio se ha concluido su viabilidad como materiales de reemplazo total o parcial de las materias primas convencionales, para la producción de ladrillos. Estos ladrillos cumplen además con las normas vigentes. Este es un estudio novedoso

  3. Semimanufacture intended to be mounted on a vibrating wall or a vibrating panel for actively damping vibrations of the wall, wall or panel provided with such semimanufacture, system provided with a semimanufacture and a control unit, wall or panel provided with a control unit and method for damping audible vibrations of a wall or panel

    NARCIS (Netherlands)

    Goeje, de Marius; Overbeek, van Michiel Wilbert R.M.; Waal, van der Adri; Berkhoff, Arthur P.; Nederveen, Peter J.

    2006-01-01

    A semimanufacture intended to be mounted on a vibrating wall or a vibrating panel for actively damping the vibrations in the wall or the panel with frequencies which are at least partly audible, wherein the semimanufacture is provided with a plate wherein the plate is integrated with: at least one v

  4. [Design Method Analysis and Performance Comparison of Wall Filter for Ultrasound Color Flow Imaging].

    Science.gov (United States)

    Wang, Lutao; Xiao, Jun; Chai, Hua

    2015-08-01

    The successful suppression of clutter arising from stationary or slowly moving tissue is one of the key issues in medical ultrasound color blood imaging. Remaining clutter may cause bias in the mean blood frequency estimation and results in a potentially misleading description of blood-flow. In this paper, based on the principle of general wall-filter, the design process of three classes of filters, infinitely impulse response with projection initialization (Prj-IIR), polynomials regression (Pol-Reg), and eigen-based filters are previewed and analyzed. The performance of the filters was assessed by calculating the bias and variance of a mean blood velocity using a standard autocorrelation estimator. Simulation results show that the performance of Pol-Reg filter is similar to Prj-IIR filters. Both of them can offer accurate estimation of mean blood flow speed under steady clutter conditions, and the clutter rejection ability can be enhanced by increasing the ensemble size of Doppler vector. Eigen-based filters can effectively remove the non-stationary clutter component, and further improve the estimation accuracy for low speed blood flow signals. There is also no significant increase in computation complexity for eigen-based filters when the ensemble size is less than 10.

  5. Revisiting the Lie-group symmetry method for turbulent channel flow with wall transpiration

    CERN Document Server

    Khujadze, George

    2016-01-01

    The Lie-group-based symmetry analysis, as first proposed in Avsarkisov et al. (2014) and then later modified in Oberlack et al. (2015), to generate invariant solutions in order to predict the scaling behavior of a channel flow with uniform wall transpiration, is revisited. By focusing first on the results obtained in Avsarkisov et al. (2014), we failed to reproduce two key results: (i) For different transpiration rates at a constant Reynolds number, the mean velocity profiles (in deficit form) do not universally collapse onto a single curve as claimed. (ii) The universally proposed logarithmic scaling law in the center of the channel does not match the direct numerical simulation (DNS) data for the presented parameter values. In fact, no universal scaling behavior in the center of the channel can be detected from their DNS data, as it is misleadingly claimed in Avsarkisov et al. (2014). Moreover, we will demonstrate that the assumption of a Reynolds-number independent symmetry analysis is not justified for th...

  6. Quantification of the relative contribution of the different right ventricular wall motion components to right ventricular ejection fraction: the ReVISION method.

    Science.gov (United States)

    Lakatos, Bálint; Tősér, Zoltán; Tokodi, Márton; Doronina, Alexandra; Kosztin, Annamária; Muraru, Denisa; Badano, Luigi P; Kovács, Attila; Merkely, Béla

    2017-03-27

    Three major mechanisms contribute to right ventricular (RV) pump function: (i) shortening of the longitudinal axis with traction of the tricuspid annulus towards the apex; (ii) inward movement of the RV free wall; (iii) bulging of the interventricular septum into the RV and stretching the free wall over the septum. The relative contribution of the aforementioned mechanisms to RV pump function may change in different pathological conditions.Our aim was to develop a custom method to separately assess the extent of longitudinal, radial and anteroposterior displacement of the RV walls and to quantify their relative contribution to global RV ejection fraction using 3D data sets obtained by echocardiography.Accordingly, we decomposed the movement of the exported RV beutel wall in a vertex based manner. The volumes of the beutels accounting for the RV wall motion in only one direction (either longitudinal, radial, or anteroposterior) were calculated at each time frame using the signed tetrahedron method. Then, the relative contribution of the RV wall motion along the three different directions to global RV ejection fraction was calculated either as the ratio of the given direction's ejection fraction to global ejection fraction and as the frame-by-frame RV volume change (∆V/∆t) along the three motion directions.The ReVISION (Right VentrIcular Separate wall motIon quantificatiON) method may contribute to a better understanding of the pathophysiology of RV mechanical adaptations to different loading conditions and diseases.

  7. Level set method for numerical simulation of a cavitation bubble, its growth, collapse and rebound near a rigid wall

    Institute of Scientific and Technical Information of China (English)

    Juntao Huang; Huisheng Zhang

    2007-01-01

    A level set method of non-uniform grids is used to simulate the whole evolution of a cavitation bubble, inclu-ding its growth, collapse and rebound near a rigid wall. Single-phase Navier-Stokes equation in the liquid region is solved by MAC projection algorithm combined with second-order ENO scheme for the advection terms. The moving inter-face is captured by the level set function, and the interface velocity is resolved by "one-side" velocity extension from the liquid region to the bubble region, complementing the second-order weighted least squares method across the inter-face and projection inside bubble. The use of non-uniform grid overcomes the difficulty caused by the large computatio-nal domain and very small bubble size. The computation is very stable without suffering from large flow-field gradients, and the results are in good agreements with other studies. The bubble interface kinematics, dynamics and its effect on the wall are highlighted, which shows that the code can effecti-vely capture the "shock wave"-like pressure and velocity at jet impact, toroidal bubble, and complicated pressure struc-ture with peak, plateau and valley in the later stage of bubble oscillating.

  8. Determination of optimum insulation thicknesses using economical analyse for exterior walls of buildings with different masses

    Directory of Open Access Journals (Sweden)

    Okan Kon

    2017-07-01

    Full Text Available In this study, five different cities were selected from the five climatic zones according to Turkish standard TS 825, and insulation thicknesses of exterior walls of sample buildings were calculated by using optimization. Vertical perforated bricks with density of 550 kg/m3 and 1000 kg/m3 were chosen within the study content. Glass wool, expanded polystyrene (XPS, extruded polystyrene (EPS were considered as insulation materials. Additionally, natural gas, coal, fuel oil and LPG were utilized as fuel for heating process while electricity was used for cooling.  Life cycle cost (LCC analysis and degree-day method were the approaches for optimum insulation thickness calculations. As a result, in case of usage vertical perforated bricks with density of 550 kg/m3 and 1000 kg/m3 resulted different values in between 0.005-0.007 m (5-7 mm in the optimum insulation thickness calculations under different insulation materials.  Minimum optimum insulation thickness was calculated in case XPS was preferred as insulation material, and the maximum one was calculated in case of using glass wool.

  9. Analysis of All-Carbon Brick Bottom and Ceramic Cup Synthetic Hearth Bottom

    Institute of Scientific and Technical Information of China (English)

    ZHAO Hong-bo; CHENG Shu-sen; ZHAO Min-ge

    2007-01-01

    One of the bottlenecks of the blast furnace (BF) campaign is the life length of hearth bottom. The basic reason for the erosion of hearth bottom is its direct contact with hot metal. According to the theory of heat transfer, models of BF hearth bottom are built based on the actual examples using software and VC language, and the calculated results are in good agreement with the data of BF dissection after blowing out. The temperature distribution and the capability of the resistance to erosion for different structures of hearth bottom are analyzed, especially the two prevalent kinds of hearth bottom arrangements called "the method of heat transfer" for all-carbon brick bottom and "the method of heat isolation" for ceramic synthetic hearth bottom. Features of the two kinds of hearth bottoms are analyzed. Also the different ways of protecting the hearth bottom are clarified, according to some actual examples. After that, the same essence of prolonging life, and the fact that the existence of a "protective skull" with low thermal conductivity between the hot metal and brick layers is of utmost importance are shown.

  10. Differences of serum parathyroid hormone levels and its gene polymorphism in different ethnic groups in drinking brick-tea-borne endemic fluorosis areas

    Institute of Scientific and Technical Information of China (English)

    孙静

    2014-01-01

    Objective In this study,the differences of serum parathyroid hormone(PTH)and its gene polymorphism in different ethnic groups in drinking brick-tea-borne endemic fluorosis areas were investigated.Methods Inhabitants over the age of 16 years old in Inner Mongolia,Qinghai and Xinjiang were investigated.The questionnaire survey included basic information,dietary survey

  11. Experimental study on shear property of autoclaved fly ash brick masonry in Xinjiang region%新疆地区蒸压粉煤灰实心砖砌体抗剪性能试验研究

    Institute of Scientific and Technical Information of China (English)

    袁康; 陈燕华; 常新军; 何志军

    2011-01-01

    Autoclaved fly ash brick is classified as one new wall material to replace fired brick, promoting the shear property of autoclaved fly ash brick masonry is very important for improving the earthquake resistance and crack resistance of masonry structure.Because of fluting the surface of brick,the shear property of ribbed autoclaved fly ash brick masonry would be improved. In the paper,the shear property of ribbed autoclaved fly ash brick masonry, common autoclaved fly ash brick masonry and fired brick have been comparative studied,and the earthquake resistance and crack resistance measures have been discussed under the premise of relative standard citations,in order to provide the theoretical basis for autoclaved fly ash brick's further promotion and application in Xinjiang which is located in seismic high-incidence area, while have climate characteristics of dry climate, high annual temperature difference,high diurnal temperature difference.%蒸压粉煤灰砖属于可以替代烧结普通砖的新型墙体材料,提高蒸压粉煤灰砖砌体的抗剪性能是改善此类砌体结构抗震、抗裂能力的关键.带肋蒸压粉煤灰砖通过改善砖的外形,在砖的表面开槽形成肋状,可提高砖砌体的抗剪能力.本文对带肋蒸压粉煤灰砖砌体、普通蒸压粉煤灰砖砌体和烧结普通砖砌体的抗剪性能进行了比较研究,并结合相关规范条文探讨了带肋蒸压粉煤灰砖的有关抗震、抗裂措施,为蒸压粉煤灰砖在地处地震高发区同时具备气候干燥,年温差、日温差大的新疆地区推广应用提供理论依据.

  12. Optimization of single-walled carbon nanotube solubility by noncovalent PEGylation using experimental design methods

    Directory of Open Access Journals (Sweden)

    Hadidi N

    2011-04-01

    Full Text Available Naghmeh Hadidi1, Farzad Kobarfard2, Nastaran Nafissi-Varcheh3, Reza Aboofazeli11Department of Pharmaceutics, 2Department of Pharmaceutical Chemistry, 3Department of Pharmaceutical Biotechnology, School of Pharmacy, Shaheed Beheshti University of Medical Sciences, Tehran, IranAbstract: In this study, noncovalent functionalization of single-walled carbon nanotubes (SWCNTs with phospholipid-polyethylene glycols (Pl-PEGs was performed to improve the solubility of SWCNTs in aqueous solution. Two kinds of PEG derivatives, ie, Pl-PEG 2000 and Pl-PEG 5000, were used for the PEGylation process. An experimental design technique (D-optimal design and second-order polynomial equations was applied to investigate the effect of variables on PEGylation and the solubility of SWCNTs. The type of PEG derivative was selected as a qualitative parameter, and the PEG/SWCNT weight ratio and sonication time were applied as quantitative variables for the experimental design. Optimization was performed for two responses, aqueous solubility and loading efficiency. The grafting of PEG to the carbon nanostructure was determined by thermogravimetric analysis, Raman spectroscopy, and scanning electron microscopy. Aqueous solubility and loading efficiency were determined by ultraviolet-visible spectrophotometry and measurement of free amine groups, respectively. Results showed that Pl-PEGs were grafted onto SWCNTs. Aqueous solubility of 0.84 mg/mL and loading efficiency of nearly 98% were achieved for the prepared Pl-PEG 5000-SWCNT conjugates. Evaluation of functionalized SWCNTs showed that our noncovalent functionalization protocol could considerably increase aqueous solubility, which is an essential criterion in the design of a carbon nanotube-based drug delivery system and its biodistribution.Keywords: phospholipid-PEG, D-optimal design, loading efficiency, Raman spectroscopy, scanning electron microscopy, theromogravimetric analysis, carbon nanotubes

  13. A practical proposal for solving the world's cigarette butt problem: Recycling in fired clay bricks.

    Science.gov (United States)

    Mohajerani, Abbas; Kadir, Aeslina Abdul; Larobina, Luke

    2016-06-01

    The disposal and littering of cigarette butts (CBs) is a serious environmental problem. Trillions of cigarettes are produced every year worldwide, resulting in millions of tonnes of toxic waste being dumped into the environment in the form of cigarette butts. As CBs have poor biodegradability, it can take many years for them to break down. This paper reviews and presents some of the results of a study on the recycling of CBs into fired clay bricks. Bricks with 2.5%, 5%, 7.5%, and 10% CB content by weight were manufactured and tested, and then compared against control clay bricks with 0% CB content. The results showed that the dry density decreased by up to 30% and the compressive strength decreased by 88% in bricks with 10% CBs. The calculated compressive strength of bricks with 1% CBs was determined to be 19.53Mpa. To investigate the effect of mixing time, bricks with 7.5% CB content were manufactured with different mixing times of 5, 10, and 15min. To test the effect of heating time on the properties of CB bricks, the heating rate used during manufacturing was changed to 0.7, 2, 5, and 10°Cmin(-1). Bricks with 0% and 5% CB content were fired with these heating rates. Leachate tests were carried out for bricks with 0%, 2.5%, 5%, and 10% CB content. The emissions released during firing were tested for bricks with 0% and 5% CB content using heating rates of 0.7, 2, 5, and 10°Cmin(-1). The gases tested were carbon monoxide (CO), carbon dioxide (CO2), chlorine (Cl2), nitrogen oxide (NO), and hydrogen cyanide (HCN). Finally, estimations were made for the energy that could be saved by firing bricks incorporating CBs. Calculations showed that up to 58% of the firing energy could potentially be saved. Bricks were shown to be a viable solution for the disposal of CBs. They can reduce contamination caused by cigarette butts and provide a masonry construction material that can be either loadbearing or non-loadbearing, depending on the quantity of CBs incorporated. This

  14. Field and laboratory determination of a poly(vinyl/vinylidene chloride) additive in brick mortar.

    Science.gov (United States)

    Law, S L; Newman, J H; Ptak, F L

    1990-02-01

    A polymerized vinyl/vinylidene chloride additive, used in brick mortar during the 60s and 70s, is detected at the building site by the field method, which employs a commercially available chloride test strip. The field test results can then be verified by the laboratory methods. In one method, total chlorine in the mortar is determined by an oxygen-bomb method and the additive chloride is determined by difference after water-soluble chlorides have been determined on a separate sample. In the second method, the polymerized additive is extracted directly from the mortar with tetrahydrofuran (THF). The difference in weight before and after extraction of the additive gives the weight of additive in the mortar. Evaporation of the THF from the extract leaves a thin film of the polymer, which gives an infrared "fingerprint" spectrum characteristic of the additive polymer.

  15. Use of Greenlandic resources for the production of bricks

    DEFF Research Database (Denmark)

    Belmonte, Louise Josefine

    knowledge gap was identified and covered: • to identify and conduct initial testing on waste types, which could be of interest in Greenlandic brick production. The waste types investigated in this study were municipal solid waste incineration (MSWI) ashes and tailings from the mining industry. The major...... of e.g. compression strength, open porosity and water absorption can be produced from the sediments. However, the properties largely depend on the processing of the sediment, e.g. firing procedure and initial treatments. • Addition of waste materials, such as the investigated bottom ash and mine...... characteristics. • Bricks are heterogeneous materials, which can accommodate materials of wide ranging compositions without losing their technical properties. For this reason, the ceramic industry has been identified as one of the major recipients for waste in the future. Wastes of different types are becoming...

  16. OSL studies of local bricks for retrospective dosimetric application

    Science.gov (United States)

    Singh, A. K.; Menon, S. N.; Kadam, S. Y.; Koul, D. K.; Datta, D.

    2016-09-01

    Luminescence properties of quartz extracted from bricks has been reported worldwide for its use in dose estimation in case of nuclear or radiological accident. Accordingly, in this study the feasibility of utilizing the optically stimulated luminescence (OSL) emission of quartz extracted from red bricks collected from three different locations in and around Mumbai, India for retrospective dosimetry was explored. Thermoluminescence and OSL characterization of the samples were carried out. The growth curve, thermal stability and equivalent dose plateau of the OSL signal suggested the signals to be well behaving. Subsequently, the dose recovery tests carried for different administered doses, using single aliquot regenerative protocol, demonstrated the feasibility of the OSL emissions of these samples for dose evaluation in retrospective dosimetry.

  17. PARAMETRIC STUDY FOR THE PREPARATION OF ALIGNED SINGLE-WALLED CARBON NANOTUBES BY ANODE-ARC DISCHARGE METHOD

    Institute of Scientific and Technical Information of China (English)

    J.F. Dai; Q. Wang; W.X. Li; Z.Q. Wei; G.J. Xu

    2005-01-01

    Well aligned quasi-straight single-walled carbon nanotubes (SWCNTs) and straight SWCNTs bundle have been prepared in large scale by anode-arc vaporization of graphite with metallic catalysts. Various parameters such as the catalyst preparation, the kinds and pressure of the buffer gases, the quantity of anode-arc current intensity, and the method of purification have been examined. The influence of these parameters on the deposited carbon yield is reported, together with observations of the produced material. Improvement in synthetic techniques has resulted in the optimal conditions for the production of large quantities of high quality SWCNTs in our semi-continuous synthesis method. The formation of carbon nanotubes (CNTs) was studied briefly in this paper. Owing to the magnetic pinching effect of arc current, the CNTs arrange in parallel lines along the arc current direction.

  18. Development of Wall Thinning Distinction Method using the Multi-inspecting UT Data of Carbon Steel Piping

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Kyeong Mo; Yun, Hun; Lee, Chan Kyoo [KEPCO E and C, Yongin (Korea, Republic of)

    2012-05-15

    To manage the wall thinning of carbon steel piping in nuclear power plants, the utility of Korea has performed thickness inspection for some quantity of pipe components during refueling outages and determined whether repair or replacement after evaluating UT (Ultrasonic Test) data. When the existing UT data evaluation methods, such as Band, Blanket, PTP (Point to Point) Methods, are applied to a certain pipe component, unnecessary re-inspecting situations may be generated even though the component does not thinned. In those cases, economical loss caused by repeated inspection and problems of maintaining the pipe integrity followed by decreasing of newly inspected components may be generated. EPRI (Electric Power Research Institute) in USA has suggested several statistical methods, TPM (Total Point Method), LSS (Least Square Slope) Method, etc. to distinguish whether multiple inspecting components have thinned or not. This paper presents the analysis results for multiple inspecting components over three times based on both NAM (Near Area of Minimum) Method developed by KEPCO-E and C and the other methods suggested by EPRI.

  19. Unfired clay bricks – retention curves and liquid diffusivities

    DEFF Research Database (Denmark)

    Hansen, Kurt Kielsgaard; Peuhkuri, Ruut Hannele; Kristensen, A.

    2002-01-01

    This paper presents retention curves and liquid diffusivities of two different types of unfired clay bricks, both produced in Denmark on commercial basis. The retention curves are determined by use of pressure plate and pressure membrane apparatuses. The liquid diffusivity is calculated on the ba...... on the basis of capillary rise of water measured by use of X-ray equipment. The data from the capillary rise of water is transformed by the Boltzmann transformation....

  20. Energy Efficiency Improvement Potential in Historical Brick Building

    OpenAIRE

    Žogla, Gatis; Blumberga, Andra; Zvaigznītis, Kristaps; Dzikēvičs, Miķelis; Blumberga, Dagnija; Burinskiene, Marija

    2013-01-01

    Energy efficiency in historical heritage buildings is viewed as a taboo because these buildings usually are law-protected and no energy efficiency measures that would change the appearance of building are allowed. In this paper we look at a potential of increasing energy efficiency level in historical buildings. Measurements to determine energy efficiency of a historical brick building have been done, which also give the possibility to determine the potential of energy efficiency measures in ...