WorldWideScience

Sample records for breeder reactor program

  1. The United States of America fast breeder reactor program

    International Nuclear Information System (INIS)

    The reasons for the development of the fast breeder reactor in the United States are outlined, and the LMFBR program is discussed in detail, under the following headings: program objectives, reactor physics, fuel and materials development, fuel recycle, safety, components, plant experience program (Near Commercial Breeder Reactor). The special facilities to be used at each stage of the program are described. It is planned that the Near Commercial Breeder Reactor will be complete in 1986, and commercial plants should follow in rapid succession. An alternate fast reactor concept (Gas Cooled Fast Reactor) is outlined. The Environmental Impact Statement for the proposed program is summarized, and the cost benefit analysis supplied as part of the Environment Statement is also summarized. (U.K.)

  2. Water cooled breeder program summary report (LWBR (Light Water Breeder Reactor) development program)

    Energy Technology Data Exchange (ETDEWEB)

    1987-10-01

    The purpose of the Department of Energy Water Cooled Breeder Program was to demonstrate pratical breeding in a uranium-233/thorium fueled core while producing electrical energy in a commercial water reactor generating station. A demonstration Light Water Breeder Reactor (LWBR) was successfully operated for more than 29,000 effective full power hours in the Shippingport Atomic Power Station. The reactor operated with an availability factor of 76% and had a gross electrical output of 2,128,943,470 kilowatt hours. Following operation, the expended core was examined and no evidence of any fuel element defects was found. Nondestructive assay of 524 fuel rods determined that 1.39 percent more fissile fuel was present at the end of core life than at the beginning, proving that breeding had occurred. This demonstrates the existence of a vast source of electrical energy using plentiful domestic thorium potentially capable of supplying the entire national need for many centuries. To build on the successful design and operation of the Shippingport Breeder Core and to provide the technology to implement this concept, several reactor designs of large breeders and prebreeders were developed for commercial-sized plants of 900--1000 Mw(e) net. This report summarizes the Water Cooled Breeder Program from its inception in 1965 to its completion in 1987. Four hundred thirty-six technical reports are referenced which document the work conducted as part of this program. This work demonstrated that the Light Water Breeder Reactor is a viable alternative as a PWR replacement in the next generation of nuclear reactors. This transition would only require a minimum of change in design and fabrication of the reactor and operation of the plant.

  3. BREEDER: a microcomputer program for financial analysis of a large-scale prototype breeder reactor

    International Nuclear Information System (INIS)

    This report describes a microcomputer-based, single-project financial analysis program: BREEDER. BREEDER is a user-friendly model designed to facilitate frequent and rapid analyses of the financial implications associated with alternative design and financing strategies for electric generating plants and large-scale prototype breeder (LSPB) reactors in particular. The model has proved to be a useful tool in establishing cost goals for LSPB reactors. The program is available on floppy disks for use on an IBM personal computer (or IBM look-a-like) running under PC-DOS or a Kaypro II transportable computer running under CP/M (and many other CP/M machines). The report documents version 1.5 of BREEDER and contains a user's guide. The report also includes a general overview of BREEDER, a summary of hardware requirements, a definition of all required program inputs, a description of all algorithms used in performing the construction-period and operation-period analyses, and a summary of all available reports. The appendixes contain a complete source-code listing, a cross-reference table, a sample interactive session, several sample runs, and additional documentation of the net-equity program option

  4. BREEDER: a microcomputer program for financial analysis of a large-scale prototype breeder reactor

    Energy Technology Data Exchange (ETDEWEB)

    Giese, R.F.

    1984-04-01

    This report describes a microcomputer-based, single-project financial analysis program: BREEDER. BREEDER is a user-friendly model designed to facilitate frequent and rapid analyses of the financial implications associated with alternative design and financing strategies for electric generating plants and large-scale prototype breeder (LSPB) reactors in particular. The model has proved to be a useful tool in establishing cost goals for LSPB reactors. The program is available on floppy disks for use on an IBM personal computer (or IBM look-a-like) running under PC-DOS or a Kaypro II transportable computer running under CP/M (and many other CP/M machines). The report documents version 1.5 of BREEDER and contains a user's guide. The report also includes a general overview of BREEDER, a summary of hardware requirements, a definition of all required program inputs, a description of all algorithms used in performing the construction-period and operation-period analyses, and a summary of all available reports. The appendixes contain a complete source-code listing, a cross-reference table, a sample interactive session, several sample runs, and additional documentation of the net-equity program option.

  5. Fast Breeder Reactor studies

    International Nuclear Information System (INIS)

    This report is a compilation of Fast Breeder Reactor (FBR) resource documents prepared to provide the technical basis for the US contribution to the International Nuclear Fuel Cycle Evaluation. The eight separate parts deal with the alternative fast breeder reactor fuel cycles in terms of energy demand, resource base, technical potential and current status, safety, proliferation resistance, deployment, and nuclear safeguards. An Annex compares the cost of decommissioning light-water and fast breeder reactors. Separate abstracts are included for each of the parts

  6. Fast Breeder Reactor studies

    Energy Technology Data Exchange (ETDEWEB)

    Till, C.E.; Chang, Y.I.; Kittel, J.H.; Fauske, H.K.; Lineberry, M.J.; Stevenson, M.G.; Amundson, P.I.; Dance, K.D.

    1980-07-01

    This report is a compilation of Fast Breeder Reactor (FBR) resource documents prepared to provide the technical basis for the US contribution to the International Nuclear Fuel Cycle Evaluation. The eight separate parts deal with the alternative fast breeder reactor fuel cycles in terms of energy demand, resource base, technical potential and current status, safety, proliferation resistance, deployment, and nuclear safeguards. An Annex compares the cost of decommissioning light-water and fast breeder reactors. Separate abstracts are included for each of the parts.

  7. Liquid Metal Fast Breeder Reactor Program: Argonne facilities

    Energy Technology Data Exchange (ETDEWEB)

    Stephens, S. V. [comp.

    1976-09-01

    The objective of the document is to present in one volume an overview of the Argonne National Laboratory test facilities involved in the conduct of the national LMFBR research and development program. Existing facilities and those under construction or authorized as of September 1976 are described. Each profile presents brief descriptions of the overall facility and its test area and data relating to its experimental and testing capability. The volume is divided into two sections: Argonne-East and Argonne-West. Introductory material for each section includes site and facility maps. The profiles are arranged alphabetically by title according to their respective locations at Argonne-East or Argonne-West. A glossary of acronyms and letter designations in common usage to describe organizations, reactor and test facilities, components, etc., involved in the LMFBR program is appended.

  8. Report to the Congress: liquid metal fast breeder reactor program--past, present, and future, Energy Research and Development Administration

    Energy Technology Data Exchange (ETDEWEB)

    1975-04-28

    The past, present, and future of the liquid metal fast breeder reactor (LMFBR) program, the Nation's highest priority energy program, are studied. ERDA anticipates that the operation of the first large commercial breeder will start in 1987, and that 186 commercial-size breeders will be in operation by the year 2000. The breeder program is made up of six major areas, each dealing with an important element of technology: reactor physics; fuels and materials; fuel recycle; safety; component development; plant experience; and facilities used in the LMFBR program. ERDA is implementing a new system for administering, managing, and controlling the breeder program that will provide increased program visibility and control. Federal funding for breeder development was $168 million in FY 1971, accounting for 40% of the total Federal R and D energy budget; in FY 1976 Federal funding for this program will be $474 million, only 26% of total Federal funding for energy research. Besides Federal funds, over half a billion dollars have been or will be invested by industry over the next 5 to 10 years to develop the breeder and to build a demonstration plant. Five other nations--the United Kingdom, France, Japan, West Germany, and the Soviet Union--have a high priority national energy program for developing the LMFBR. These foreign breeder programs could contribute important data and information to the U.S. program. (BYB)

  9. Breeder reactor fuel fabrication system development

    International Nuclear Information System (INIS)

    Significant progress has been made in the design and development of remotely operated breeder reactor fuel fabrication and support systems (e.g., analytical chemistry). These activities are focused by the Secure Automated Fabrication (SAF) Program sponsored by the Department of Energy to provide: a reliable supply of fuel pins to support US liquid metal cooled breeder reactors and at the same time demonstrate the fabrication of mixed uranium/plutonium fuel by remotely operated and automated methods

  10. Fast breeder reactor research

    International Nuclear Information System (INIS)

    , Italy, in April or May 1977. Recognizing the importance of international co-ope ration within the framework of IWGFR for preparing surveys, proposals and recommendations concerning sodium cooled fast breeder reactors, the Working Group prepared a number of joint documents with the help of experts from the participating countries, discussed them at the Eighth Annual Meeting and made recommendations on the preparation of subsequent joint documents. (author)

  11. Installation of the Light-Water Breeder Reactor at the Shippingport Atomic Power Station (LWBR Development Program)

    International Nuclear Information System (INIS)

    This report summarizes the refueling operations performed to install a Light Water Breeder Reactor (LWBR) core into the existing pressurized water reactor vessel at the Shippingport Atomic Power Station. Detailed descriptions of the major installation operations (e.g., primary system preconditioning, fuel installation, pressure boundary seal welding) are included as appendices to this report; these operations are of technical interest to any reactor servicing operation, whether the reactor is a breeder or a conventional light water non-breeder core

  12. Summary of several hydraulic tests in support of the light water breeder reactor design (LWBR development program)

    International Nuclear Information System (INIS)

    As part of the Light Water Breeder Reactor development program, hydraulic tests of reactor components were performed. This report presents the results of several of those tests performed for components which are somewhat unique in their application to a pressurized water reactor design. The components tested include: triplate orifices used for flow distribution purposes, multiventuri type flowmeters, tight lattice triangular pitch rod support grids, fuel rod end support plates, and the balance piston which is a major component of the movable fuel balancing system. Test results include component pressure loss coefficients, flowmeter coefficients and fuel rod region pressure drop characteristics

  13. Fusion Breeder Program interim report

    International Nuclear Information System (INIS)

    This interim report for the FY82 Fusion Breeder Program covers work performed during the scoping phase of the study, December, 1981-February 1982. The goals for the FY82 study are the identification and development of a reference blanket concept using the fission suppression concept and the definition of a development plan to further the fusion breeder application. The context of the study is the tandem mirror reactor, but emphasis is placed upon blanket engineering. A tokamak driver and blanket concept will be selected and studied in more detail during FY83

  14. End-of-life destructive examination of light water breeder reactor fuel rods (LWBR Development Program)

    International Nuclear Information System (INIS)

    Destructive examination of 12 representative Light Water Breeder Reactor fuel rods was performed following successful operation in the Shippingport Atomic Power Station for 29,047 effective full power hours, about five years. Light Water Breeder Reactor fuel rods were unique in that the thorium oxide and uranium-233 oxide fuel was contained within Zircaloy-4 cladding. Destructive examinations included analysis of released fission gas; chemical analysis of the fuel to determine depletion, iodine, and cesium levels; chemical analysis of the cladding to determine hydrogen, iodine, and cesium levels; metallographic examination of the cladding, fuel, and other rod components to determine microstructural features and cladding corrosion features; and tensile testing of the irradiated cladding to determine mechanical strength. The examinations confirmed that Light Water Breeder Reactor fuel rod performance was excellent. No evidence of fuel rod failure was observed, and the fuel operating temperature was low (below 25800F at which an increased percentage of fission gas is released). 21 refs., 80 figs., 20 tabs

  15. End-of-life destructive examination of light water breeder reactor fuel rods (LWBR Development Program)

    Energy Technology Data Exchange (ETDEWEB)

    Richardson, K.D.

    1987-10-01

    Destructive examination of 12 representative Light Water Breeder Reactor fuel rods was performed following successful operation in the Shippingport Atomic Power Station for 29,047 effective full power hours, about five years. Light Water Breeder Reactor fuel rods were unique in that the thorium oxide and uranium-233 oxide fuel was contained within Zircaloy-4 cladding. Destructive examinations included analysis of released fission gas; chemical analysis of the fuel to determine depletion, iodine, and cesium levels; chemical analysis of the cladding to determine hydrogen, iodine, and cesium levels; metallographic examination of the cladding, fuel, and other rod components to determine microstructural features and cladding corrosion features; and tensile testing of the irradiated cladding to determine mechanical strength. The examinations confirmed that Light Water Breeder Reactor fuel rod performance was excellent. No evidence of fuel rod failure was observed, and the fuel operating temperature was low (below 2580/sup 0/F at which an increased percentage of fission gas is released). 21 refs., 80 figs., 20 tabs.

  16. Review of ORNL-TSF shielding experiments for the gas-cooled Fast Breeder Reactor Program

    Energy Technology Data Exchange (ETDEWEB)

    Abbott, L.S.; Ingersoll, D.T.; Muckenthaler, F.J.; Slater, C.O.

    1982-01-01

    During the period between 1975 and 1980 a series of experiments was performed at the ORNL Tower Shielding Facility in support of the shield design for a 300-MW(e) Gas Cooled Fast Breeder Demonstration Plant. This report reviews the experiments and calculations, which included studies of: (1) neutron streaming in the helium coolant passageways in the GCFR core; (2) the effectiveness of the shield designed to protect the reactor grid plate from radiation damage; (3) the adequacy of the radial shield in protecting the PCRV (prestressed concrete reactor vessel) from radiation damage; (4) neutron streaming between abutting sections of the radial shield; and (5) the effectiveness of the exit shield in reducing the neutron fluxes in the upper plenum region of the reactor.

  17. Description of a materials/coolant laboratory for support of the Breeder Reactor Technology Shipping Program

    International Nuclear Information System (INIS)

    A description of a facility devoted to evaluating the environmental compatibility and mechanical response of materials suitable for a breeder reactor spent-fuel shipping cask is given. The facility presently consists of a closed-loop servo-controlled hydraulic, horizontal test system coupled to an environmental chamber, generalized mechanical test equipment and high-rate mechanical behavior apparatus. Future plans include the procurement of real-time computer control equipment which will be used to assess the effects of complex load-time histories on spent-fuel shipping cask materials

  18. Breeder Reactors, Understanding the Atom Series.

    Science.gov (United States)

    Mitchell, Walter, III; Turner, Stanley E.

    The theory of breeder reactors in relationship to a discussion of fission is presented. Different kinds of reactors are characterized by the cooling fluids used, such as liquid metal, gas, and molten salt. The historical development of breeder reactors over the past twenty-five years includes specific examples of reactors. The location and a brief…

  19. Shippingport operations with the Light Water Breeder Reactor core. (LWBR Development Program)

    International Nuclear Information System (INIS)

    This report describes the operation of the Shippingport Atomic Power Station during the LWBR (Light Water Breeder Reactor) Core lifetime. It also summarizes the plant-oriented operations during the period preceding LWBR startup, which include the defueling of The Pressurized Water Reactor Core 2 (PWR-2) and the installation of the LWBR Core, and the operations associated with the defueling of LWBR. The intent of this report is to examine LWBR experience in retrospect and present pertinent and significant aspects of LWBR operations that relate primarily to the nuclear portion of the Station. The nonnuclear portion of the Station is discussed only as it relates to overall plant operation or to unusual problems which result from the use of conventional equipment in radioactive environments. 30 refs., 69 figs., 27 tabs

  20. Shippingport operations with the Light Water Breeder Reactor core. (LWBR Development Program)

    Energy Technology Data Exchange (ETDEWEB)

    Budd, W.A. (ed.)

    1986-03-01

    This report describes the operation of the Shippingport Atomic Power Station during the LWBR (Light Water Breeder Reactor) Core lifetime. It also summarizes the plant-oriented operations during the period preceding LWBR startup, which include the defueling of The Pressurized Water Reactor Core 2 (PWR-2) and the installation of the LWBR Core, and the operations associated with the defueling of LWBR. The intent of this report is to examine LWBR experience in retrospect and present pertinent and significant aspects of LWBR operations that relate primarily to the nuclear portion of the Station. The nonnuclear portion of the Station is discussed only as it relates to overall plant operation or to unusual problems which result from the use of conventional equipment in radioactive environments. 30 refs., 69 figs., 27 tabs.

  1. Fast breeder reactor protection system

    Science.gov (United States)

    van Erp, J.B.

    1973-10-01

    Reactor protection is provided for a liquid-metal-fast breeder reactor core by measuring the coolant outflow temperature from each of the subassemblies of the core. The outputs of the temperature sensors from a subassembly region of the core containing a plurality of subassemblies are combined in a logic circuit which develops a scram alarm if a predetermined number of the sensors indicate an over temperature condition. The coolant outflow from a single subassembly can be mixed with the coolant outflow from adjacent subassemblies prior to the temperature sensing to increase the sensitivity of the protection system to a single subassembly failure. Coherence between the sensors can be required to discriminate against noise signals. (Official Gazette)

  2. Fabrication and loading of fuel rods for the Light Water Breeder Reactor (LWBR Development Program)

    International Nuclear Information System (INIS)

    The fabrication and inspection operations used for the manufacture of approximately 24,000 fuel rods for the Light Water Breeder Reactor are described in detail. This report also describes the development work to establish the fabrication procedures and investigations undertaken to solve problems encountered during manufacturing. The approximately 10 foot long LWBR fuel rods were made in four outside diameters ranging from 0.306 inch (seed) to 0.832 inch (reflector). Each rod was fabricated by sealing cylindrical oxide fuel pellets (ThO2-U233O2), into Zircaloy seamless tubes by welding Zircaloy enclosures at the ends. The special inspections performed to assure a high quality product meeting all design requirements are described. These inspections included weld radiography and ultrasonic inspection, in-motion radiography to evaluate internal dimensions and pellet integrity, helium leak testing, corrosion testing, and detection of surface contamination. The facilities designed and built for this fabrication effort are described and the resultant manufacturing yields are presented. 13 refs., 42 figs., 20 tabs

  3. Fast breeder reactors an engineering introduction

    CERN Document Server

    Judd, A M

    1981-01-01

    Fast Breeder Reactors: An Engineering Introduction is an introductory text to fast breeder reactors and covers topics ranging from reactor physics and design to engineering and safety considerations. Reactor fuels, coolant circuits, steam plants, and control systems are also discussed. This book is comprised of five chapters and opens with a brief summary of the history of fast reactors, with emphasis on international and the prospect of making accessible enormous reserves of energy. The next chapter deals with the physics of fast reactors and considers calculation methods, flux distribution,

  4. Liquid metal tribology in fast breeder reactors

    International Nuclear Information System (INIS)

    Liquid Metal Cooled Fast Breeder Reactors (LMFBR) require mechanisms operating in various sodium liquid and sodium vapor environments for extended periods of time up to temperatures of 900 K under different chemical properties of the fluid. The design of tribological systems in those reactors cannot be based on data and past experience of so-called conventional tribology. Although basic tribological phenomena and their scientific interpretation apply in this field, operating conditions specific to nuclear reactors and prevailing especially in the nuclear part of such facilities pose special problems. Therefore, in the framework of the R and D-program accompanying the construction phase of SNR 300 experiments were carried out to provide data and knowledge necessary for the lay-out of friction systems between mating surfaces of contacting components. Initially, screening tests isolated material pairs with good slipping properties and maximum wear resistance. Those materials were subjected to comprehensive parameter investigations. A multitude of laboratory scale tests have been performed under largely reactor specific conditions. Unusual superimpositions of parameters were analyzed and separated to find their individual influence on the friction process. The results of these experiments were made available to the reactor industry as well as to factories producing special tribo-materials. (orig.)

  5. Design, implementation and cost-benefit analysis of a dynamic testing program in the Experimental Breeder Reactor-II

    International Nuclear Information System (INIS)

    Dynamic tests have been performed for many years in commercial pressurized and boiling water reactors. The purpose of this study was to evaluate the technological and economical feasibility of extending the current light water reactor testing procedures to both present and future liquid metal fast breeder reactors. A 38 node linearized, lumped parameter, EBR-II system model was developed. This model was analyzed to obtain the predicted system time and frequency response for reactivity perturbations, intermediate heat exchanger secondary inlet sodium temperature perturbation frequency response, and various system nodal frequency response sensitivities

  6. Gas-cooled fast breeder reactor

    International Nuclear Information System (INIS)

    Almost all the R D works of gas-cooled fast breeder reactor in the world were terminated at the end of the year 1980. In order to show that the R D termination was not due to technical difficulties of the reactor itself, the present paper describes the reactor plant concept, reactor performances, safety, economics and fuel cycle characteristics of the reactor, and also describes the reactor technologies developed so far, technological problems remained to be solved and planned development schedules of the reactor. (author)

  7. Improved fuel element for fast breeder reactor

    International Nuclear Information System (INIS)

    The invention, in which the United States Department of Energy has participated as co-inventor, relates to breeder reactor fuel elements, and specifically to such elements incorporating 'getters', hereafter designated as fission product traps. The main object of the invention is the construction of a fast breeder reactor fuel pin, free from local stresses induced in the cladding by reactions with cesium. According to the invention, the fast breeder fuel element includes a cladding tube, sealed at both ends by a plug, and containing a fissile stack and a fertile stack, characterized by the interposition of a cesium trap between the fissile and fertile stacks. The trap is effective at reactor operating temperatures in retaining and separating the cesium generated in the fissile material and preventing cesium reaction with the fertile stack. Depending on the construction method adopted, the trap may consists of a low density titanium oxide or niobium oxide pellet

  8. Experimental Breeder Reactor I Preservation Plan

    Energy Technology Data Exchange (ETDEWEB)

    Julie Braun

    2006-10-01

    Experimental Breeder Reactor I (EBR I) is a National Historic Landmark located at the Idaho National Laboratory, a Department of Energy laboratory in southeastern Idaho. The facility is significant for its association and contributions to the development of nuclear reactor testing and development. This Plan includes a structural assessment of the interior and exterior of the EBR I Reactor Building from a preservation, rather than an engineering stand point and recommendations for maintenance to ensure its continued protection.

  9. Operating experience of Fast Breeder Test Reactor

    International Nuclear Information System (INIS)

    Fast Breeder Test Reactor (FBTR) is a 40 MWt / 13.2 MWe sodium cooled, loop type mixed carbide fuelled reactor. Its main aim is to gain experience in the design, construction and operation of fast reactors and to serve as an irradiation facility for development of fuel and structural material for future fast reactors. The reactor achieved first criticality in October 1985 with small indigenously designed and fabricated Mark I core (70% PuC-30% UC). The reactor power was subsequently raised in steps to 17.4 MWt by addition of Mark II fuel subassemblies (55% PuC-45% UC) and with the Mark I fuel operating at the designed linear heat rating of 400 W/cm. The turbo-generator was synchronized with the grid in July 1997. The achieved peak burn-up is 137 000 MWd/t so far without any fuel-clad failure. Presently the reactor is being operated at a nominal power of 15.7 MWt for irradiation of a test fuel subassembly of the Prototype Fast Breeder Reactor, which is coming up at Kalpakkam. It is also planned to irradiate test subassemblies made of metallic fuel for future fast reactor program. Being a small reactor, all feed back coefficients of reactivity including void coefficient are negative and hence the reactor is inherently safe. This was confirmed by carrying out physics tests. The capability to remove decay heat under various incidental conditions including natural convection was demonstrated by carrying out engineering tests. Thermo couples are provided for on-line monitoring of fuel SA outlet temperature by dedicated real time computer and processed to generate trip signals for the reactor in case of power excursion, increase in clad hot spot temperature and subassembly flow blockage. All pipelines and capacities in primary main circuit are provided with segmented outer envelope to minimize and contain radioactive sodium leak while ensuring forced cooling through reactor to remove decay heat in case of failure of primary boundary. In secondary circuit, provision is

  10. Potential of duplex fuel in prebreeder, breeder, and power reactor designs: tests and analyses (AWBA Development Program)

    International Nuclear Information System (INIS)

    Dual region fuel pellets, called duplex pellets, are comprised of an outer annular region of relatively high uranium fuel enrichment and a center pellet of fertile material with no enrichment. UO2 and ThO2 are the fissile and fertile materials of interest. Both prebreeders and breeders are discussed as are the performance advantages of duplex pellets over solid pellets in these two pressurized water reactor types. Advantages of duplex pellets for commercial reactor fuel rods are also discussed. Both irradiation test data and analytical results are used in comparisons. Manufacturing of duplex fuel is discussed

  11. Coatings for fast breeder reactor components

    International Nuclear Information System (INIS)

    Several types of metallurgical coatings are used in the unique environments of the fast breeder reactor. Most of the coatings have been developed for tribological applications, but some also serve as corrosion barriers, diffusion barriers, or radionuclide traps. The materials that have consistently given the best performance as tribological coatings in the breeder reactor environments have been coatings based on chromium carbide, nickel aluminide, or Tribaloy 700 (a nickel-base hard-facing alloy). Other coatings that have been qualified for limited applications include chromium plating for low temperature galling protection and nickel plating for radionuclide trapping

  12. Final environmental statement, Liquid Metal Fast Breeder Reactor Program. Volume 1

    International Nuclear Information System (INIS)

    Information is presented under the following section headings: LMFBR program options and their compatibility with the major issues affecting commercial development, Proposed Final Environmental Statement for the LMFBR program, December 1974, WASH-1535, supplemental material, and material relating to Proposed Final Environmental Statement review

  13. Experiences with fast breeder reactor education in laboratory and short course settings

    International Nuclear Information System (INIS)

    The breeder reactor industry throughout the world has grown impressively over the last two decades. Despite the uncertainties in some national programs, breeder reactor technology is well established on a global scale. Given the magnitude of this technological undertaking, there has been surprisingly little emphasis on general breeder reactor education - either at the university or laboratory level. Many universities assume the topic too specialized for including appropriate courses in their curriculum - thus leaving students entering the breeder reactor industry to learn almost exclusively from on-the-job experience. The evaluation of four course presentations utilizing visual aids is presented

  14. Status of fast breeder reactor development in the United States

    International Nuclear Information System (INIS)

    The energy policy of the United States is aimed at shifting as rapidly as practicable from an oil dependent economy to one that relies heavily on other fuels and energy sources. Nuclear power Is now and is expected to continue to be an important factor in achieving this goal. If nuclear power is to contribute to a solution of future energy needs, demonstration of the breeder reactor as a viable source of essentially inexhaustible energy supply is essential. The US DOE program for development of the fast breeder reactor has witnessed some notable events in the past year. Foremost among these Is the successful operational testing of the Fast Flux Test Facility (FFTF), located at.the Hanford Engineering Development Laboratory. The reactor reached full design power of 400 MW(t) on December 21, 1980, and has performed remarkably close to design specifications. Design of the Clinch River Breeder Reactor Plant (CRBRP), a 375 MW(e) LMFBR, is now over 80 percent complete. About $530 million in components have been ordered; component deliveries total approximately $124 million; work-in-process totals another $204 million. Construction of the plant, however, has been suspended since 1977. With the concurrence of the U.S. Congress and approvals from the appropriate authorities work on the safety review and site clearing for construction can resume. The Conceptual Design Study for a large, 1000 MW(e) LMFBR Large Developmental Plant was recently completed on a schedule commensurate with submission of a full report to the Congress at the end of March, 1981. This report is the culmination of a study which began in October, 1978 and involved contributions from U.S. reactor manufacturers and US DOE laboratories. The US DOE is carrying forward a comprehensive technology development program. This effort provides direct support to the FFTF and CRBRP projects and to the LDP. It also supports technology development which is generic to the overall LMFBR program. Funding for breeder

  15. Prototype fast breeder reactor main options

    International Nuclear Information System (INIS)

    Fast reactor programme gets importance in the Indian energy market because of continuous growing demand of electricity and resources limited to only coal and FBR. India started its fast reactor programme with the construction of 40 MWt Fast Breeder Test Reactor (FBTR). The reactor attained its first criticality in October 1985. The reactor power will be raised to 40 MWt in near future. As a logical follow-up of FBTR, it was decided to build a prototype fast breeder reactor, PFBR. Considering significant effects of capital cost and construction period on economy, systematic efforts are made to reduce the same. The number of primary and secondary sodium loops and components have been reduced. Sodium coolant, pool type concept, oxide fuel, 20% CW D9, SS 316 LN and modified 9Cr-1Mo steel (T91) materials have been selected for PFBR. Based on the operating experience, the integrity of the high temperature components including fuel and cost optimization aspects, the plant temperatures are recommended. Steam temperature of 763 K at 16.6 MPa and a single TG of 500 MWe gross output have been decided. PFBR will be located at Kalpakkam site on the coast of Bay of Bengal. The plant life is designed for 30 y and 75% load factor. In this paper the justifications for the main options chosen are given in brief. (author). 2 figs, 2 tabs

  16. Large scale breeder reactor pump dynamic analyses

    International Nuclear Information System (INIS)

    The lateral natural frequency and vibration response analyses of the Large Scale Breeder Reactor (LSBR) primary pump were performed as part of the total dynamic analysis effort to obtain the fabrication release. The special features of pump modeling are outlined in this paper. The analysis clearly demonstrates the method of increasing the system natural frequency by reducing the generalized mass without significantly changing the generalized stiffness of the structure. Also, a method of computing the maximum relative and absolute steady state responses and associated phase angles at given locations is provided. This type of information is very helpful in generating response versus frequency and phase angle versus frequency plots

  17. Reliability modeling of Clinch River breeder reactor electrical shutdown systems

    International Nuclear Information System (INIS)

    The initial simulation of the probabilistic properties of the Clinch River Breeder Reactor Plant (CRBRP) electrical shutdown systems is described. A model of the reliability (and availability) of the systems is presented utilizing Success State and continuous-time, discrete state Markov modeling techniques as significant elements of an overall reliability assessment process capable of demonstrating the achievement of program goals. This model is examined for its sensitivity to safe/unsafe failure rates, sybsystem redundant configurations, test and repair intervals, monitoring by reactor operators; and the control exercised over system reliability by design modifications and the selection of system operating characteristics. (U.S.)

  18. Thermal and neutronic calculation for fast breeder reactor FBR

    International Nuclear Information System (INIS)

    This research included studying of thermal and neutronic calculation for fast breeder nuclear reactor, to putting the optimum design for this reactor. So a Soviet type (BN-350) was chosen, which has its core composed of two enrichment zones, and with blanket that contains depleted uranium. A group of thermal calculation programs was made by using personal computer, to obtain core and blanket reactor dimensions and volume fractions of reaction input material and number and dimensions of fuel rods which were used for neutron calculations. Several core and blanket enrichments were used to study neutron flux behaviour for two reactors different conditions. First when control rods exist in the core reactor and second when the rods are out of the core. Breeding ratio was also studied for different core and blanket enrichment. 30 tabs.; 24 figs.; 34 refs.; 3 apps

  19. Safeguards in Prototype Fast Breeder Reactor Monju

    International Nuclear Information System (INIS)

    The assemblies loaded in the core and stored in the ex-vessel storage tank (EVST) are in liquid sodium in the Japanese prototype fast breeder reactor (FBR) Monju. Since it is difficult to apply a direct verification procedure for the fuel assemblies in these areas, a dual containment and surveillance system consisting of two monitoring devices such as surveillance camera and radiation monitor that are functionally independent has been applied. In addition, the Monju Remote Monitoring System was developed to strengthen the continuous surveillance and to reduce the load of the inspection activities. Furthermore, the ex-vessel transfer machine radiation monitor (EVRM) and the exit gate monitor (EXGM) were upgraded to strengthen the monitoring of spent blanket fuel assemblies and to improve the reliability of distinguishing between fuel assemblies and non-fuel items. As the result, the integrated safeguards was introduced in November 2009, and the effective safeguards activities have been implemented in Monju. (author)

  20. Water chemistry of breeder reactor steam generators

    International Nuclear Information System (INIS)

    The water quality requirements will be described for breeder reactor steam generators, as well as specifications for balance of plant protection. Water chemistry details will be discussed for the following power plant conditions: feedwater and recirculation water at above and below 5% plant power, refueling or standby, makeup water, and wet layup. Experimental data will be presented from tests which included a departure from nucleate boiling experiment, the Few Tube Test, with a seven tube evaporator and three tube superheater, and a verification of control and on-line measurement of sodium ion in the ppB range. Sampling and instrumentation requirements to insure adherence to the specified water quality will be described. Evaporator cleaning criteria and data from laboratory testing of chemical cleaning solutions with emphasis on flow, chemical composition, and temperature will be discussed

  1. Exploding the myths about the fast breeder reactor

    Energy Technology Data Exchange (ETDEWEB)

    Burns, S.

    1979-01-01

    This paper discusses the facts and figures about the effects of conservation policies, the benefits of the Clinch River Breeder Reactor demonstration plant, the feasibility of nuclear weapons manufacture from reactor-grade plutonium, diversion of plutonium from nuclear plants, radioactive waste disposal, and the toxicity of plutonium. The paper concludes that the U.S. is not proceeding with a high confidence strategy for breeder development because of a variety of false assumptions.

  2. The breeder reactor in electricity supply

    International Nuclear Information System (INIS)

    Forecasts are made of Britain's energy prospects in the year 2000. It is concluded that fossil fuels and renewable energy sources will leave an energy gap and that dependence on nuclear power will be substantial. There will, however have been a rapid depletion of readily available uranium ore reserves and a growing availability of plutonium from thermal reactors. Britain's resources of plutonium and depleted uranium which the fast breeder reactor can use - will equal many thousand million tonnes of coal. Our nuclear programme should therefore include one or two FBRs. Resources should be pooled internationally and plants built to prove alternative options and consolidate an already highly developed technology. In Britain our earliest nuclear (Magnox) stations have served as well. In Scotland, where next year an estimated 30% of electricity output will be nuclear, Hunterston 'B' AGR has had a splendid first year of operation, and pumped storage capacity in Scotland has extended the benefits of low-cost generation. The FBR has many very satisfactory engineering features and is eminently controllable and well behaved. It is compact, with relatively low cooling-water requirements and it could be built, one hopes, close to our load centres. There can be confidence that it will be proved safe. An order for an FBR, on the earliest timescale that fits in with evidence of successful operation of the Dounreay PFR and an agreed international programme, would serve the national interest and ensure the survival of our plant manufacturers, so badly hit by the effects of stagnation of the U.K. economy. (author)

  3. Anticipated transients without scram for light water reactors: implications for liquid metal fast breeder reactors

    International Nuclear Information System (INIS)

    In the design of light water reactors (LWRs), protection against anticipated transients (e.g., loss of normal electric power and control rod withdrawal) is provided by a highly reliable scram, or shutdown system. If this system should become inoperable, however, the transient could lead to a core meltdown. The Nuclar Regulatory Commission (NRC) has proposed, in NUREG-0460 [1], new requirements (or acceptance criteria) for anticipated transients without scram (ATWS) events and the manner in which they could be considered in the design and safety evaluation of LWRs. This note assesses the potential impact of the proposed LWR-ATWS criteria on the liquid metal fast breeder reactor (LMFBR) safety program as represented by the Clinch River Breeder Reactor Plant

  4. Quality assurance in technology development for The Clinch River Breeder Reactor Plant Project

    International Nuclear Information System (INIS)

    The Clinch River Breeder Reactor Plant Project is the nation's first large-scale demonstration of the Liquid Metal Fast Breeder Reactor (LMFBR) concept. The Project has established an overall program of plans and actions to assure that the plant will perform as required. The program has been established and is being implemented in accordance with Department of Energy Standard RDT F 2-2. It is being applied to all parts of the plant, including the development of technology supporting its design and licensing activity. A discussion of the program as it is applied to development is presented

  5. Status of fast breeder reactor development in the United States of America - April 1984

    International Nuclear Information System (INIS)

    The Breeder Technology program continues to produce viable information on fuel performance, nuclear systems technology, and power conversion technology. The unique testing capabilities design into the FFTF have resulted in well-validated materials and fuels irradiation information that has confirmed and extended previous data bases. Current directions for the research and development program are to improve the technology for power conversion systems, components, instrumentation, and materials technology to the point where cost reduction and reliability potentials are realized. Operation of the breeder test facility complex at the Hanford Engineering Development Laboratory (HEDL), the Energy Technology Engineering Center (ETEC), and the Argonne National Laboratory (ANL) continues to provide the experience base and test capability for the breeder R and D effort. International cooperation will be even more important in the future than in the past for several reasons. Significant new investments still have to be made in breeder R and D to improve designs, achieve economic competitiveness and to develop practical breeder fuel cycle capabilities. Progress can be accelerated, redundancies avoided, and economics achieved if nations coordinate their programs, and where possible, divide up the work. In addition, there is clear mutual benefit in encouraging the countries involved in breeder development to harmonize standards and regulations related to safety. It is also important that the advanced nations work together closely in assuring that adequate international safeguards, export controls, and national physical security measures keep pace with breeder reactor and fuel cycle developments

  6. Shutdown and Closure of the Experimental Breeder Reactor - II

    International Nuclear Information System (INIS)

    The Department of Energy mandated the termination of the Integral Fast Reactor (IFR) Program, effective October 1, 1994. To comply with this decision, Argonne National Laboratory-West (ANL-W) prepared a plan providing detailed requirements to maintain the Experimental Breeder Reactor - II (EBR-II) in a radiologically and industrially safe condition, including removal of all irradiated fuel assemblies from the reactor plant, and removal and stabilization of the primary and secondary sodium, a liquid metal used to transfer heat within the reactor plant. The EBR-II is a pool-type reactor. The primary system contained approximately 325 m3 (86,000 gallons) of sodium and the secondary system contained 50 m3 (13,000 gallons). In order to properly dispose of the sodium in compliance with the Resource Conservation and Recovery Act (RCRA), a facility was built to react the sodium to a solid sodium hydroxide monolith for burial as a low level waste in a land disposal facility. Deactivation of a liquid metal fast breeder reactor (LMFBR) presents unique concerns. Residual amounts of sodium remaining in circuits and components must be passivated, inerted, or removed to preclude future concerns with sodium-air reactions that could generate potentially explosive mixtures of hydrogen and leave corrosive compounds. The passivation process being implemented utilizes a moist carbon dioxide gas that generates a passive layer of sodium carbonate/sodium bicarbonate over any quantities of residual sodium. Tests being conducted will determine the maximum depths of sodium that can be reacted using this method, defining the amount that must be dealt with later to achieve RCRA clean closure. Deactivation of the EBR-II complex is on schedule for a March, 2002, completion. Each system associated with EBR-II has an associated lay-up plan defining the system end state, as well as instructions for achieving the lay-up condition. A goal of system-by-system lay-up is to minimize surveillance and

  7. Shutdown and closure of the experimental breeder reactor - II

    International Nuclear Information System (INIS)

    The Department of Energy mandated the termination of the Integral Fast Reactor (IFR) Program, effective October 1, 1994. To comply with this decision, Argonne National Laboratory-West (ANL-W) prepared a plan providing detailed requirements to maintain the Experimental Breeder Reactor-II (EBR-II) in a radiologically and industrially safe condition, including removal of all irradiated fuel assemblies from the reactor plant, and removal and stabilization of the primary and secondary sodium, a liquid metal used to transfer heat within the reactor plant. The EBR-II is a pool-type reactor. The primary system contained approximately 325 m3 (86,000 gallons) of sodium and the secondary system contained 50 m3 (13,000 gallons). In order to properly dispose of the sodium in compliance with the Resource Conservation and Recovery Act (RCRA), a facility was built to react the sodium to a solid sodium hydroxide monolith for burial as a low level waste in a land disposal facility. Deactivation of a liquid metal fast breeder reactor (LMFBR) presents unique concerns. Residual amounts of sodium remaining in circuits and components must be passivated, inerted, or removed to preclude future concerns with sodium-air reactions that could generate potentially explosive mixtures of hydrogen and leave corrosive compounds. The passivation process being implemented utilizes a moist carbon dioxide gas that generates a passive layer of sodium carbonate/sodium bicarbonate over any quantities of residual sodium. Tests being conducted will determine the maximum depths of sodium that can be reacted using this method, defining the amount that must be dealt with later to achieve RCRA clean closure. Deactivation of the EBR-II complex is on schedule for a March, 2002, completion. Each system associated with EBR-II has an associated layup plan defining the system end state, as well as instructions for achieving the layup condition. A goal of system-by-system layup is to minimize surveillance and

  8. The breeder spent fuel packaging and transportation program

    International Nuclear Information System (INIS)

    The Breeder Spent Fuel Handling and Transportation Program of the United States Department of Energy (DOE) was established in 1983 in order to develop a reliable planning base for interface development at the back end of the liquid metal fast breeder reactor (LMFBR) fuel cycle. It began by addressing the immediate interface needs between the planned Clinch River Breeder Reactor, near Oak Ridge, Tennessee, and the proposed Breeder Reprocessing Engineering Test Facility at Richland, Washington, and concluded by providing a developmental plan leading to a sodium-cooled spent breeder fuel transportation cask for a mature 20-reactor LMFBR industry in the year 2025. During the formulation of this plan, as well as during the technology development that constituted the programme, liaison between the DOE and the concerned private industry operations was maintained by frequent meetings. As a result of functional considerations, it was decided that a legal truck-weight stainless steel multi-assembly package would both be economical and would have unlimited routine possibilities and facility access. As the detailed conceptual design emerged, it included remotely workable, spring-loaded, captive bolts to reduce occupational exposure, internal integral impact limiters and a structurally promising depleted uranium gamma shield. Modular baskets of a boron-aluminium alloy, produced by Fonderies Montupet of France, would enhance criticality control and heat transfer, as well as allowing for either a spent fuel or high level waste payload. While preliminary calculations have qualified the structure and shielding, heat transfer from a six-assembly payload still poses problems. Details are discussed in the paper. (author)

  9. 快堆钠回路水锤程序开发与应用%Waterhammer Program Development and Application for Fast Breeder Reactor's Sodium Circus

    Institute of Scientific and Technical Information of China (English)

    文静; 栾霖; 金德圭; 陆道纲; 汤荣铭

    2001-01-01

    研究开发了快堆钠回路水锤分析专用程序WHA。该程序在一维特征线法(MOC)传统的压力波传播数学模型中补充了钠腔-气腔外边界模型,并采用气泡离散模型模拟低压液柱分离中的蒸汽穴的生成与溃灭。程序用FORTRAN90语言对快堆实验钠回路ESPRESSO中由于阀门的快速开启与关闭引起的压力波传播进行了分析计算。计算结果表明:将钠腔-气腔引入水锤压力波传播的数学模型进行程序计算的结果是合理的。%Based on one-dimensional method of characteristics(MOC), anumerical model of pressure-wave progation is presented in the paper. A special code is programmed to analyze and calculate waterhammer resulted from rapid opening or closing of valve in the experimental sodium circus of fast breeder reactor(FBR). In the model, a new outer boundary condition, sodium-cavity is included. Model of bubble's discrete distribution is adopted to simulate generation and collapse of the bubble with the pressure's decreasing and increasing. The results demonstrate that the model of pressure-wave progation is valid.

  10. Fission-suppressed hybrid reactor: the fusion breeder

    International Nuclear Information System (INIS)

    Results of a conceptual design study of a 233U-producing fusion breeder are presented. The majority of the study was devoted to conceptual design and evaluation of a fission-suppressed blanket and to fuel cycle issues such as fuel reprocessing, fuel handling, and fuel management. Studies in the areas of fusion engineering, reactor safety, and economics were also performed

  11. Fission-suppressed hybrid reactor: the fusion breeder

    Energy Technology Data Exchange (ETDEWEB)

    Moir, R.W.; Lee, J.D.; Coops, M.S.

    1982-12-01

    Results of a conceptual design study of a /sup 233/U-producing fusion breeder are presented. The majority of the study was devoted to conceptual design and evaluation of a fission-suppressed blanket and to fuel cycle issues such as fuel reprocessing, fuel handling, and fuel management. Studies in the areas of fusion engineering, reactor safety, and economics were also performed.

  12. Symposium on key questions about the fast breeder reactor

    International Nuclear Information System (INIS)

    Except for several introductions on various aspects of the fast breeder reactor development this paper contains the full texts of the discussions held in the sub-groups panels on resp. technical matters, environment and health, society, politics and economics. The main issues of each discussion are summarized

  13. Clinch River Breeder Reactor Plant Project: construction schedule

    International Nuclear Information System (INIS)

    The construction schedule for the Clinch River Breeder Reactor Plant and its evolution are described. The initial schedule basis, changes necessitated by the evaluation of the overall plant design, and constructability improvements that have been effected to assure adherence to the schedule are presented. The schedule structure and hierarchy are discussed, as are tools used to define, develop, and evaluate the schedule

  14. Calculational model used in the analysis of nuclear performance of the Light Water Breeder Reactor (LWBR) (LWBR Development Program)

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, L.B. (ed.)

    1978-08-01

    The calculational model used in the analysis of LWBR nuclear performance is described. The model was used to analyze the as-built core and predict core nuclear performance prior to core operation. The qualification of the nuclear model using experiments and calculational standards is described. Features of the model include: an automated system of processing manufacturing data; an extensively analyzed nuclear data library; an accurate resonance integral calculation; space-energy corrections to infinite medium cross sections; an explicit three-dimensional diffusion-depletion calculation; a transport calculation for high energy neutrons; explicit accounting for fuel and moderator temperature feedback, clad diameter shrinkage, and fuel pellet growth; and an extensive testing program against experiments and a highly developed analytical standard.

  15. Status of national programmes on fast breeder reactors

    International Nuclear Information System (INIS)

    The twenty-second Annual Meeting of the International Working Group on Fast Reactors took place in Vienna, 18-21 April 1989. Nineteen representatives from twelve Member States and International Organizations attended the Meeting. This publication is a collection of presentations in which the participants reported the status of their national programmes on fast breeder reactors. A separate abstract was prepared for each of the twelve papers from this collections. Refs, figs, tabs and 1 graph

  16. The nuclear question at the start of the '80s: the breeder reactor

    International Nuclear Information System (INIS)

    The four newspaper articles and the letter cover the following matters: general introduction about breeder reactors and the situation in Swedish politics; visit to Dounreay to discuss breeder reactors (breeding, safety, plutonium production, radiation protection); PuO2-UO2 mixed fuel; description of breeder reactors; efficiency in use of U-235; DFR and PFR; breeder reactors in Swedish politics (arguments for and against nuclear power in general, breeder reactors in particular); discussion of the future of nuclear power in Sweden. (U.K.)

  17. Feasibility study on the thorium fueled boiling water breeder reactor

    International Nuclear Information System (INIS)

    The feasibility of (Th,U)O 2 fueled, boiling water breeder reactor based on conventional BWR technology has been studied. In order to determine the potential use of water cooled thorium reactor as a competitive breeder, this study evaluated criticality, breeding and void reactivity coefficient in response to changes made in MFR and fissile enrichments. The result of the study shows that while using light water as moderator, low moderator to fuel volume ratio (MFR=0.5), it was possible to breed fissile fuel in negative void reactivity condition. However the burnup value was lower than the value of the current LWR. On the other hand, heavy water cooled reactor shows relatively wider feasible breeding region, which lead into possibility of designing a core having better neutronic and economic performance than light water with negative void reactivity coefficient. (authors)

  18. Instrumentation and control improvements at Experimental Breeder Reactor II

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, L.J.; Planchon, H.P.

    1993-01-01

    The purpose of this paper is to describe instrumentation and control (I C) system improvements at Experimental Breeder Reactor 11 (EBR-11). The improvements are focused on three objectives; to keep the reactor and balance of plant (BOP) I C systems at a high level of reliability, to provide diagnostic systems that can provide accurate information needed for analysis of fuel performance, and to provide systems that will be prototypic of I C systems of the next generation of liquid metal reactor (LMR) plants.

  19. Elements for evaluation of fast breeder reactor's potential in Argentina

    International Nuclear Information System (INIS)

    Fast Breeder Reactors (FBR) main features are presented in a general form, including their physical principles, the history of their evolution, their relevant technological aspects and the basis for their comparison to other energy sources. This is completed with descriptions of typical reactors and a model of FBR penetration in the Argentine electrical network. It is recommended to form a multidisciplinary board to study which position should be taken with respect to this type of reactors. In the author's opinion a Research activity should be started and gradually increased for passing to Development activities after a short while. (Author)

  20. Instrumentation and control improvements at Experimental Breeder Reactor II

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, L.J.; Planchon, H.P.

    1993-03-01

    The purpose of this paper is to describe instrumentation and control (I&C) system improvements at Experimental Breeder Reactor 11 (EBR-11). The improvements are focused on three objectives; to keep the reactor and balance of plant (BOP) I&C systems at a high level of reliability, to provide diagnostic systems that can provide accurate information needed for analysis of fuel performance, and to provide systems that will be prototypic of I&C systems of the next generation of liquid metal reactor (LMR) plants.

  1. Binary breeder reactor: an option for Brazilian energy future

    International Nuclear Information System (INIS)

    To assure a continued supply of electric energy beyond a few decades from now, developmemnt of fast breeder reactors is a necessity. Binary fueled LMFBRs combine an improvement in the inherent safety of fast reactors and an efficient use of the abundant thorium. A nuclear system that starts with PWRs and gradually shifts to a FBR system or to a FBR-PWR symbiotic system appears to be the most reasonable one for Brazil. Natural uranium requirements and possible sequences of reactor introductions are discussed for some postulated Brazilian situations. A permanent system of approx. 100 GWe capacity can be established based on the estimated resource of natural uranium. (Author)

  2. Binary breeder reactor an option for Brazilian energy future

    International Nuclear Information System (INIS)

    To assure a continued supply of electric energy beyond a few decades from now, development of fast breeder reactors is a necessity. Binary fueled LMFBRs combine an improvement in the inherent safety of fast reactors and an efficient use of the abundant thorium. A nuclear system that starts with PWRs and gradually shifts to a FBR system or to a FBR-PWR symbiotic system appears to be the most resonable one for Brazil. Natural uranium requirements and possible sequences of reactor introductions are discussed for some postulated Brazilian situations. A permanent system of approximatelly 100 GWe capacity can be established based on the estimated resource of natural uranium. (Author)

  3. Preparation of LWBR [Light Water Breeder Reactor] spent fuel for shipment to ICPP [Idaho Chemical Processing Plant] for long term storage (LWBR Development Program)

    International Nuclear Information System (INIS)

    After successfully operating for 29,047 effective full power hours, the Light Water Breeder Reactor (LWBR) core was defueled prior to total decommissioning of the Shippingport facility. All nuclear fuel and much of the reactor internal hardware was removed from the reactor vessel. Non-fuel components were prepared for shipment to disposal sites, and the fuel assemblies were partially disassembled and shipped to the Expended Core Facility (ECF) in Idaho. At ECF, the fuel modules underwent further disassembly to provide fuel rods for nondestructive testing to establish the core's breeding efficiency and to provide core components for examinations to assess their performance characteristics. This report presents a basic description of the processes and equipment used to prepare and to ship all LWBR nuclear fuel to the Idaho Chemical Processing Plant (ICPP) for long-term storage. Preparation processes included the underwater loading of LWBR fuel into storage liners, the sealing, dewatering and drying of the storage liners, and the final pressurization of the storage liners with inert neon gas. Shipping operations included the underwater installation of the fuel loaded storage liner into the Peach Bottom shipping cask, cask removal from the waterpit, cask preparations for shipping, and cask shipment by tractor trailer to the ICPP facility for long-term storage. The ICPP facility preparations for LWBR fuel storage and the ICPP process for discharge of the fuel into underground silos are presented. 10 refs., 42 figs

  4. Plutonium bearing oxide fuels for recycling in thermal reactors and fast breeder reactors

    International Nuclear Information System (INIS)

    Programs carried out in the past two decades have established the technical feasibility of using plutonium as a fuel material in both water-cooled power reactors and sodium-cooled fast breeder reactors. The problem facing the technical community is basically one of demonstrating plutonium fuel recycle under strict conditions of public safety, accountability, personnel exposure, waste management, transportation and diversion or theft which are still evolving. In this paper only technical and economic aspects of high volume production and the demonstration program required are discussed. This paper discusses the role of mixed oxide fuels in light water reactors and the objectives of the LMFBR required for continual growth of nuclear power during the next century. The results of studies showing the impact of using plutonium on uranium requirements, power costs, and the market share of nuclear power are presented. The influence of doubling time and the introduction date of LMFBRs on the benefits to be derived by its commercial use are discussed. Advanced fuel development programs scoped to meet future commerical LMFBR fuel requirements are described. Programs designed to provide the basic technology required for using plutonium fuels in a manner which will satisfy all requirements for public acceptance are described. Included are the high exposure plutonium fabrication development program centered around the High Performance Fuels Laboratory being built at the Hanford Engineering Development Laboratory and the program to confirm the technology required for the production of mixed oxide fuels for light water reactors which is being coordinated by Savannah River Laboratories

  5. Fast breeder reactors: Experience and trends. V. 2

    International Nuclear Information System (INIS)

    The IAEA Symposium on ''Fast Breeder Reactors: Experience and Future Trends'' was held, at the invitation of the Government of France, in Lyons, France, on 22-26 July 1985. It was hosted by the French Commissariat a l'energie atomique and Electricite de France. The purpose of the Symposium was to review the experience gained so far in the field of LMFBRs, taking into account the constructional, operational, technological, economic and fuel cycle aspects, and to consider the developmental trends as well as the international co-operation in fast breeder reactor design and utilization. The Symposium was attended by almost 400 participants (340 participants, 35 observers and 20 journalists) from 25 countries and five international organizations. More than 80 papers were presented and discussed during six regular sessions and four poster sessions. A separate abstract was prepared for each of these papers

  6. Status of national programmes on fast breeder reactors

    International Nuclear Information System (INIS)

    The present document contains information on the status of fast breeder reactor development and on worldwide activities in this advanced nuclear power technology during 1989 as reported at the 23rd meeting of the IWGFR in Vienna, April 1990. The publication is intended to provide information regarding the current status of LMFBR development in IAEA Member States. A separate abstract was prepared for each of the 11 papers presented by the participants of this meeting. Refs, figs and tabs

  7. Status of national programmes on fast breeder reactors

    International Nuclear Information System (INIS)

    The present document contains information on the status of fast breeder reactor development and on worldwide activities in this advanced nuclear power technology during 1990 as reported at the 24th meeting of the IWGFR in Tsuruga, Japan, 15-18 April 1991. The publication is intended to provide information regarding the current status of LMFBR development in IAEA Member States and CEC. Figs and tabs

  8. Multiple recycling of fuel in prototype fast breeder reactor

    Indian Academy of Sciences (India)

    G Pandikumar; V Gopalakrishnan; P Mohanakrishnan

    2009-05-01

    In a thermal neutron reactor, multiple recycle of U–Pu fuel is not possible due to degradation of fissile content of Pu in just one recycle. In the FBR closed fuel cycle, possibility of multi-recycle has been recognized. In the present study, Pu-239 equivalence approach is used to demonstrate the feasibility of achieving near constant input inventory of Pu and near stable Pu isotopic composition after a few recycles of the same fuel of the prototype fast breeder reactor under construction at Kalpakkam. After about five recycles, the cycle-to-cycle variation in the above parameters is below 1%.

  9. Molten Salt Breeder Reactor Analysis Methods

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jinsu; Jeong, Yongjin; Lee, Deokjung [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of)

    2015-05-15

    Utilizing the uranium-thorium fuel cycle shows considerable potential for the possibility of MSR. The concept of MSBR should be revised because of molten salt reactor's advantage such as outstanding neutron economy, possibility of continuous online reprocessing and refueling, a high level of inherent safety, and economic benefit by keeping off the fuel fabrication process. For the development of MSR research, this paper provides the MSBR single-cell, two-cell and whole core model for computer code input, and several calculation results including depletion calculation of each models. The calculations are carried out by using MCNP6, a Monte Carlo computer code, which has CINDER90 for depletion calculation using ENDF-VII nuclear data. From the calculation results of various reactor design parameters, the temperature coefficients are all negative at the initial state and MTC becomes positive at the equilibrium state. From the results of core rod worth, the graphite control rod alone cannot makes the core subcritical at initial state. But the equilibrium state, the core can be made subcritical state only by graphite control rods. Through the comparison of the results of each models, the two-cell method can represent the MSBR core model more accurately with a little more computational resources than the single-cell method. Many of the thermal spectrum MSR have adopted a multi-region single-fluid strategy.

  10. Sodium technology for fast breeder reactors

    International Nuclear Information System (INIS)

    Sodium, because of its good heat transfer and nuclear properties, is used as a coolant in fast reactors. It is also used largely as a reducing agent in pharmaceutical, perfumery and general chemical industries. Its affinity to react with air and water is a strong disadvantage. However, this is fully understood and the design of engineering systems take care of this aspect. With several experimental and test facilities established over the years in this country as well as abroad, the 'sodium technology' has reached a level of maturity. The design of sodium systems considering all the physical and chemical properties and the developmental work carried out at Indira Gandhi Centre for Atomic Research are broadly covered in this report. (author)

  11. Training experience at Experimental Breeder Reactor II

    Energy Technology Data Exchange (ETDEWEB)

    Driscoll, J.W.; McCormick, R.P.; McCreery, H.I.

    1978-01-01

    The EBR-II Training Group develops, maintains,and oversees training programs and activities associated with the EBR-II Project. The group originally spent all its time on EBR-II plant-operations training, but has gradually spread its work into other areas. These other areas of training now include mechanical maintenance, fuel manufacturing facility, instrumentation and control, fissile fuel handling, and emergency activities. This report describes each of the programs and gives a statistical breakdown of the time spent by the Training Group for each program. The major training programs for the EBR-II Project are presented by multimedia methods at a pace controlled by the student. The Training Group has much experience in the use of audio-visual techniques and equipment, including video-tapes, 35 mm slides, Super 8 and 16 mm film, models, and filmstrips. The effectiveness of these techniques is evaluated in this report.

  12. Feasibility and deployment strategy of water cooled thorium breeder reactor

    International Nuclear Information System (INIS)

    The author have studied water cooled thorium breeder reactor based on matured pressurized water reactor (PWR) plant technology for several years. Through these studies it is concluded that reduced moderated core by arranging fuel pins in a triangular tight lattice array with heavy water coolant in the primary loop by replacing original light water is appropriate for achieving sufficient breeding performance as sustainable fission system and high enough burn-up as an economical power plant. The heavy water cooled thorium reactor is feasible to be introduced by using Pu recovered from spent fuel of LWR, keeping continuity with current LWR infrastructure. This thorium reactor can be operated as sustainable energy supplier and also MA transmuter to realize future society with less long-lived nuclear waste

  13. Contained fission explosion breeder reactor system

    International Nuclear Information System (INIS)

    A reactor system for producing useful thermal energy and valuable isotopes, such as plutonium-239, uranium-233, and/or tritium, in which a pair of sub-critical masses of fissile and fertile actinide slugs are propelled into an ellipsoidal pressure vessel. The propelled slugs intercept near the center of the chamber where the concurring slugs become a more than prompt configuration thereby producing a fission explosion. Re-useable accelerating mechanisms are provided external of the vessel for propelling the slugs at predetermined time intervals into the vessel. A working fluid of lean molten metal slurry is injected into the chamber prior to each explosion for the attenuation of the explosion's effects, for the protection of the chamber's walls, and for the absorbtion of thermal energy and debris from the explosion. The working fluid is injected into the chamber in a pattern so as not to interfere with the flight paths of the slugs and to maximize the concentration of working fluid near the chamber's center. The heated working fluid is drained from the vessel and is used to perform useful work. Most of the debris from the explosion is collected as precipitate and is used for the manufacture of new slugs

  14. Development of fuels and structural materials for fast breeder reactors

    Indian Academy of Sciences (India)

    Baldev Raj; S L Mannan; P R Vasudeva Rao; M D Mathew

    2002-10-01

    Fast breeder reactors (FBRs) are destined to play a crucial role inthe Indian nuclear power programme in the foreseeable future. FBR technology involves a multi-disciplinary approach to solve the various challenges in the areas of fuel and materials development. Fuels for FBRs have significantly higher concentration of fissile material than in thermal reactors, with a matching increase in burn-up. The design of the fuel is an important aspect which has to be optimised for efficient, economic and safe production of power. FBR components operate under hostile and demanding environment of high neutron flux, liquid sodium coolant and elevated temperatures. Resistance to void swelling, irradiation creep, and irradiation embrittlement are therefore major considerations in the choice of materials for the core components. Structural and steam generator materials should have good resistance to creep, low cycle fatigue, creep-fatigue interaction and sodium corrosion. The development of carbide fuel and structural materials for the Fast Breeder Test Reactor at Kalpakkam was a great technological challenge. At the Indira Gandhi Centre for Atomic Research (IGCAR), advanced research facilities have been established, and extensive studies have been carried out in the areas of fuel and materials development. This has laid the foundation for the design and development of a 500 MWe Prototype Fast Breeder Reactor. Highlights of some of these studies are discussed in this paper in the context of our mission to develop and deploy FBR technology for the energy security of India in the 21st century.

  15. Computational intelligent systems for Prototype Fast Breeder Reactor

    International Nuclear Information System (INIS)

    Nearly 15000 process signals are digitized by physically and functionally distributed embedded systems in Prototype Fast Breeder Reactor (PFBR). Digitized signals are processed and relevant information is displayed through Large video display systems at Control Room. It is necessary that correct and reliable information need to be provided to the plant operator. Computational intelligent systems play a major role in enhancing the safe operation of the Nuclear reactor. The paper explains the features of three such systems, one for on-line validation of neutronic power channel through on-line thermal balance calculation and another for detection of anomalous reactivity addition through on-line reactivity balance computation and third for on-line computation of Reactor power from fluctuations of core thermocouple signals. (author)

  16. Fuel Summary Report: Shippingport Light Water Breeder Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Illum, D.B.; Olson, G.L.; McCardell, R.K.

    1999-01-01

    The Shippingport Light Water Breeder Reactor (LWBR) was a small water cooled, U-233/Th-232 cycle breeder reactor developed by the Pittsburgh Naval Reactors to improve utilization of the nation's nuclear fuel resources in light water reactors. The LWBR was operated at Shippingport Atomic Power Station (APS), which was a Department of Energy (DOE) (formerly Atomic Energy Commission)-owned reactor plant. Shippingport APS was the first large-scale, central-station nuclear power plant in the United States and the first plant of such size in the world operated solely to produce electric power. The Shippingport LWBR was operated successfully from 1977 to 1982 at the APS. During the five years of operation, the LWBR generated more than 29,000 effective full power hours (EFPH) of energy. After final shutdown, the 39 core modules of the LWBR were shipped to the Expended Core Facility (ECF) at Naval Reactors Facility at the Idaho National Engineering and Environmental Laboratory (INEEL). At ECF, 12 of the 39 modules were dismantled and about 1000 of more than 17,000 rods were removed from the modules of proof-of-breeding and fuel performance testing. Some of the removed rods were kept at ECF, some were sent to Argonne National Laboratory-West (ANL-W) in Idaho and some to ANL-East in Chicago for a variety of physical, chemical and radiological examinations. All rods and rod sections remaining after the experiments were shipped back to ECF, where modules and loose rods were repackaged in liners for dry storage. In a series of shipments, the liners were transported from ECF to Idaho Nuclear Technology Engineering Center (INTEC), formerly the Idaho Chemical Processing Plant (ICPP). The 47 liners containing the fully-rodded and partially-derodded core modules, the loose rods, and the rod scraps, are now stored in underground dry wells at CPP-749.

  17. Innovations in Equipment Erection of Prototype Fast Breeder Reactor (PFBR)

    International Nuclear Information System (INIS)

    Prototype Fast Breeder Reactor (PFBR) is sodium cooled, pool type reactor with generating capacity of 1250 MWt/500 MWe. Reactor assembly consists of large dimensional vessels like Safety vessel (13.54 m diameter, 12.8 m height and weight approximately 155 MT) and Main vessel (12.9 m diameter, 12.94 m height and weight approximately 202 MT including core catcher, core support structure and cooling pipes) and Steam generator (26 m length, 1.5 m diameter, and weight approximately 35 MT). PFBR reactor equipment erection was a challenging task where thin walled vessels had transported and handled with utmost precaution to avoid radial forces on the vessels which could buckle the vessels. There was a real challenge in lifting the vessels without swing, placement of large size and heavy vessel at a distance of 57 m where the crane operator had no line of site to the equipment being erected. To handle such over dimensional reactor components many mock-up tests had been carried out before erection and gained lot of confidence. Lot of care had been taken during lifting, handling and erection of thin walled over dimensional reactor components with innovative methods used for lifting fixtures, guiding arrangements, alignment fixtures and achieved the stringent erection tolerances. This paper discusses the first ever experiences gained during the handling and erection of such thin walled, over dimensional reactor components at PFBR site. (author)

  18. Conceptual design of Indian molten salt breeder reactor

    Indian Academy of Sciences (India)

    P K Vijayan; A Basak; I V Dulera; K K Vaze; S Basu; R K Sinha

    2015-09-01

    The third stage of Indian nuclear power programme envisages the use of thorium as the fertile material with 233U, which would be obtained from the operation of Pu/Th-based fast reactors in the later part of the second stage. Thorium-based reactors have been designed in many configurations, from light water-cooled designs to high-temperature liquid metal-cooled options. Another option, which holds promise, is the molten salt-fuelled reactor, which can be configured to give significant breeding ratios. A crucial part for achieving reasonable breeding in such reactors is the need to reprocess the salt continuously, either online or in batch mode. India has recently started carrying out fundamental studies so as to arrive at a conceptual design of Indian molten salt breeder reactor (IMSBR). Presently, various design options and possibilities are being studied from the point of view of reactor physics and thermal hydraulic design. In parallel, fundamental studies on natural circulation and corrosion behaviour of various molten salts have also been initiated.

  19. Fast breeder reactors: experience and trends. V. 1

    International Nuclear Information System (INIS)

    The IAEA Symposium on ''Fast Breeder Reactors: Experience and Future Trends'' was held, at the invitation of the Government of France, in Lyons, France, on 22-26 July 1985. It was hosted by the French Commissariat a l'energie atomique and Electricite de France. The purpose of the Symposium was to review the experience gained so far in the field of LMFBRs, taking into account the constructional, operational, technological, economic and fuel cycle aspects, and to consider the developmental trends as well as the international co-operation in fast breeder reactor design and utilization. The Symposium presentations were divided into sessions devoted to the following topics: Experience of LMFBR construction and operation and resultant development strategies (6 papers); LMFBR plant startup and commissioning tests and general behaviour (8 papers); Core performance experience for high burnup and core design trends (8 papers); Experience and trends in the LMFBR fuel cycle (4 papers); Core design and behaviour (3 papers); Fuels and materials (7 papers). A separate abstract was prepared for each of these papers

  20. Breeder reactors: a technique at the service of humanity

    International Nuclear Information System (INIS)

    A genuine energy policy is not conceived purely for a short term. It must on the contrary take into consideration many national and international facts in order to arrive at a balance which takes into account both the interests of the country where it is to be applied and the future interests of humanity. Growth and energy consumption make a pair. Considering the forecasts of future consumption, a rational utilization of the energy sources is a priority. The rational utilization of the energy potentialities of uranium takes a prominent place in this priority. In the fission energy of the atoms, the breeder reactors are the only types which can give their full meanings to the words economy, ecology, rationality etc. In calling for innovation, the breeder reactors are the prime movers for an advanced industry and a guarantee for the future penetration of electricity in many fields. They are thus important elements for the creation of employment. This paper also deals with questions of international cooperation, non-proliferation and the necessity for disarmament

  1. Optimisation of safety parameters in fast breeder test reactor

    International Nuclear Information System (INIS)

    Full text: Optimisation of safety parameters is an important aspect to be considered in the design of nuclear power plant and also becomes extremely important activity to be followed up during the commissioning and operating phases of the plant taking into account the operational feed back and review of incidental situations and available diversity and reliability. Otherwise, the spurious/ superfluous trips on the reactor besides affecting the availability of the plant, initiate plant transients causing stress for the plant equipment resulting in reduction of plant life. This activity has a significant role to play in attaining the maximum availability of the plant, without compromising safety. The study and evolution of optimisation process in fast breeder test reactor (FBTR); at Kalpakkam has been an interesting and rewarding experience

  2. Safeguards in the prototype fast breeder reactor MONJU

    Energy Technology Data Exchange (ETDEWEB)

    Usami, S.; Deshimaru, T.; Tomura, K. [Power Reactor and Nuclear Fuels Development Corporation, Ibaraki-ken (Japan)

    1995-12-31

    MONJU is a prototype fast breeder reactor in Japan designed to have a 280-MW(electric) output. The Power Reactor and Nuclear Fuel Development Corporation (PNC) started its construction in the autumn of 1985 in Tsuruga. The loading of the core fuel assemblies was started in October 1993, and the preoperational test is ongoing. MONJU uses 198 mixed-oxide (MOX) fuel assemblies as core fuel and 172 depleted uranium assemblies as blanket fuel. Assemblies loaded in-core and stored in the ex-vessel storage tank (EVST) reside in liquid sodium. These plutonium-containing fuel assemblies, MOX, and irradiated depleted uranium are regarded as in the difficult-to-access area, and the flows of fuel assemblies into and out of the area must be verified. Flow is verified by fuel flow monitors measuring radiation, which can limit inspector attendance during fuel handling.

  3. Degrading the Plutonium Produced in Fast Breeder Reactor Blankets

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Jor-Shan; Kuno, Yusuke [Tokyo University, 7-3-1, Hongo, Bunkyo-ku, Tokyo, 113-8656 (Japan)

    2009-06-15

    Plutonium quality, defined as the plutonium isotopic composition, is an important measure for proliferation-resistance (PR) of a nuclear energy system. The quality of the plutonium produced in the blanket assemblies of a fast breeder reactor could be as good as or better than the weapons-grade (WG). The presence of such good quality plutonium is a proliferation concern. There are various options to degrade the plutonium produced in the breeder blanket. The obvious one is to blend the blanket plutonium with those produced from the reactor core during reprocessing. Other options try to prevent the generation of good quality plutonium (Pu). The Protected Plutonium Production (P{sup 3}) Project proposed by Tokyo Institute of Technology (TIT)1,2,3 advocates the doping of certain amount of neptunium (Np), or americium (Am) in fresh blanket fuel for irradiation. The increased production of {sup 238}Pu, {sup 240}Pu and {sup 242}Pu by neutron capture in {sup 237}Np and Am would degrade the blanket plutonium. However, as {sup 237}Np is a controlled material according to IAEA, its use as doping material in fresh blanket fuel presents a concern for nuclear proliferation. In addition, the fabrication of fresh blanket fuel with inclusion of americium would be complicated due to the emission of intense low-energy gamma radiation from {sup 241}Am. Am is normally accompanied by Cm since the separation of those 2 elements is very difficult. Fuel containing both Am and Cm may make Safeguards measurement difficult. A variation would be doping the fresh blanket fuel with minor actinide (e.g., a group of neptunium, americium, and curium), or with separated reactor-grade (RG) plutonium. The drawback of such schemes would be the need for glove boxes in fresh blanket fuel fabrication. It is possible to fuel the breeder blankets with recycled (reprocessed) uranium oxide. The recycled uranium, recovered from reprocessing, contains {sup 236}U, which when irradiated in the blanket would

  4. Fast breeder reactor-block antiseismic design and verification

    International Nuclear Information System (INIS)

    The Specialists' Meeting on ''Fast Breeder Reactor-Block Antiseismic Design and Verification'' was organized by the ENEA Fast Reactor Department in co-operation with the International Working Group (IWGFR) of the International Atomic Energy Agency (IAEA), according to the recommendations of the 19th IAEA/IWGFR Meeting. It was held in Bologna, at the Headquarters of the ENEA Fast Reactor Department, on October 12-15, 1987, in the framework of the Celebrations for the Ninth Centenary of the Bologna University. The proceedings of the meeting consists of three parts. Part 1 contains the introduction and general comments, the agenda of the meeting, session summaries, conclusions and recommendations and the list of participants. Part 2 contains 8 status reports of Member States participating in the Working Group. Contributed papers were published in Part 3 and were further subdivided into 5 sessions as follows: whole reactor-block analysis (4 papers); whole reactor-block analysis (sloshing and buckling, seismic isolation effects) (8 papers); detailed core analysis (6 papers); shutdown systems and core structural and functional verifications (6 papers); component and piping analysis (7 papers). A separate abstract was prepared for each of the 8 status reports and 31 contributed papers. Refs, figs and tabs

  5. Fusion breeder

    International Nuclear Information System (INIS)

    The fusion breeder is a fusion reactor designed with special blankets to maximize the transmutation by 14 MeV neutrons of uranium-238 to plutonium or thorium to uranium-233 for use as a fuel for fission reactors. Breeding fissile fuels has not been a goal of the US fusion energy program. This paper suggests it is time for a policy change to make the fusion breeder a goal of the US fusion program and the US nuclear energy program. The purpose of this paper is to suggest this policy change be made and tell why it should be made, and to outline specific research and development goals so that the fusion breeder will be developed in time to meet fissile fuel needs

  6. Accident analysis of heavy water cooled thorium breeder reactor

    Science.gov (United States)

    Yulianti, Yanti; Su'ud, Zaki; Takaki, Naoyuki

    2015-04-01

    Thorium has lately attracted considerable attention because it is accumulating as a by-product of large scale rare earth mining. The objective of research is to analyze transient behavior of a heavy water cooled thorium breeder that is designed by Tokai University and Tokyo Institute of Technology. That is oxide fueled, PWR type reactor with heavy water as primary coolant. An example of the optimized core has relatively small moderator to fuel volume ratio (MFR) of 0.6 and the characteristics of the core are burn-up of 67 GWd/t, breeding ratio of 1.08, burn-up reactivity loss during cycles of nuclear reactor accidents types examined here is Unprotected Transient over Power (UTOP) due to withdrawing of the control rod that result in the positive reactivity insertion so that the reactor power will increase rapidly. Another accident type is Unprotected Loss of Flow (ULOF) that caused by failure of coolant pumps. To analyze the reactor accidents, neutron distribution calculation in the nuclear reactor is the most important factor. The best expression for the neutron distribution is the Boltzmann transport equation. However, solving this equation is very difficult so that the space-time diffusion equation is commonly used. Usually, space-time diffusion equation is solved by employing a point kinetics approach. However, this approach is less accurate for a spatially heterogeneous nuclear reactor and the nuclear reactor with quite large reactivity input. Direct method is therefore used to solve space-time diffusion equation which consider spatial factor in detail during nuclear reactor accident simulation. Set of equations that obtained from full implicit finite-difference method is solved by using iterative methods. The indication of UTOP accident is decreasing macroscopic absorption cross-section that results large external reactivity, and ULOF accident is indicated by decreasing coolant flow. The power reactor has a peak value before reactor has new balance condition

  7. Designing a SCADA system simulator for fast breeder reactor

    Science.gov (United States)

    Nugraha, E.; Abdullah, A. G.; Hakim, D. L.

    2016-04-01

    SCADA (Supervisory Control and Data Acquisition) system simulator is a Human Machine Interface-based software that is able to visualize the process of a plant. This study describes the results of the process of designing a SCADA system simulator that aims to facilitate the operator in monitoring, controlling, handling the alarm, accessing historical data and historical trend in Nuclear Power Plant (NPP) type Fast Breeder Reactor (FBR). This research used simulation to simulate NPP type FBR Kalpakkam in India. This simulator was developed using Wonderware Intouch software 10 and is equipped with main menu, plant overview, area graphics, control display, set point display, alarm system, real-time trending, historical trending and security system. This simulator can properly simulate the principle of energy flow and energy conversion process on NPP type FBR. This SCADA system simulator can be used as training media for NPP type FBR prospective operators.

  8. Safety and core design of large liquid-metal cooled fast breeder reactors

    OpenAIRE

    Qvist, Staffan Alexander

    2013-01-01

    In light of the scientific evidence for changes in the climate caused by greenhouse-gas emissions from human activities, the world is in ever more desperate need of new, inexhaustible, safe and clean primary energy sources. A viable solution to this problem is the widespread adoption of nuclear breeder reactor technology. Innovative breeder reactor concepts using liquid-metal coolants such as sodium or lead will be able to utilize the waste produced by the current light water reactor fuel cyc...

  9. High-temperature and breeder reactors - economic nuclear reactors of the future

    International Nuclear Information System (INIS)

    The thesis begins with a review of the theory of nuclear fission and sections on the basic technology of nuclear reactors and the development of the first generation of gas-cooled reactors applied to electricity generation. It then deals in some detail with currently available and suggested types of high temperature reactor and with some related subsidiary issues such as the coupling of different reactor systems and various schemes for combining nuclear reactors with chemical processes (hydrogenation, hydrogen production, etc.), going on to discuss breeder reactors and their application. Further sections deal with questions of cost, comparison of nuclear with coal- and oil-fired stations, system analysis of reactor systems and the effect of nuclear generation on electricity supply. (C.J.O.G.)

  10. Flow induced vibrations in liquid metal fast breeder reactors

    International Nuclear Information System (INIS)

    Flow induced vibrations are well known phenomena in industry. Engineers have to estimate their destructive effects on structures. In the nuclear industry, flow induced vibrations are assessed early in the design process, and the results are incorporated in the design procedures. In many cases, model testing is used to supplement the design process to ensure that detrimental behaviour due to flow induced vibrations will not occur in the component in question. While these procedures attempt to minimize the probability of adverse performance of the various components, there is a problem in the extrapolation of analytical design techniques and/or model testing to actual plant operation. Therefore, sodium tests or vibrational measurements of components in the reactor system are used to provide additional assurance. This report is a general survey of experimental and calculational methods in this area of structural mechanics. The report is addressed to specialists and institutions in industrialized and developing countries who are responsible for the design and operation of liquid metal fast breeder reactors. 92 refs, 90 figs, 8 tabs

  11. Molten Salt Breeder Reactor Analysis Based on Unit Cell Model

    International Nuclear Information System (INIS)

    Contemporary computer codes like the MCNP6 or SCALE are only good for solving a fixed solid fuel reactor. However, due to the molten-salt fuel, MSR analysis needs some functions such as online reprocessing and refueling, and circulating fuel. J. J. Power of Oak Ridge National Laboratory (ORNL) suggested in 2013 a method for simulating the Molten Salt Breeder Reactor (MSBR) with SCALE, which does not support continuous material processing. In order to simulate MSR characteristics, the method proposes dividing a depletion time into short time intervals and batchwise reprocessing and refueling at each step. We are applying this method by using the MCNP6 and PYTHON and NEWT-TRITON-PYTHON and PYTHON code systems to MSBR. This paper contains various parameters to analyze the MSBR unit cell model such as the multiplication factor, breeding ratio, change of amount of fuel, amount of fuel feeding, and neutron flux distribution. The result of MCNP6 and NEWT module in SCALE show some difference in depletion analysis, but it still seems that they can be used to analyze MSBR. Using these two computer code system, it is possible to analyze various parameters for the MSBR unit cells such as the multiplication factor, breeding ratio, amount of material, total feeding, and neutron flux distribution. Furthermore, the two code systems will be able to be used for analyzing other MSR model or whole core models of MSR

  12. Molten Salt Breeder Reactor Analysis Based on Unit Cell Model

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Yongjin; Choi, Sooyoung; Lee, Deokjung [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of)

    2014-05-15

    Contemporary computer codes like the MCNP6 or SCALE are only good for solving a fixed solid fuel reactor. However, due to the molten-salt fuel, MSR analysis needs some functions such as online reprocessing and refueling, and circulating fuel. J. J. Power of Oak Ridge National Laboratory (ORNL) suggested in 2013 a method for simulating the Molten Salt Breeder Reactor (MSBR) with SCALE, which does not support continuous material processing. In order to simulate MSR characteristics, the method proposes dividing a depletion time into short time intervals and batchwise reprocessing and refueling at each step. We are applying this method by using the MCNP6 and PYTHON and NEWT-TRITON-PYTHON and PYTHON code systems to MSBR. This paper contains various parameters to analyze the MSBR unit cell model such as the multiplication factor, breeding ratio, change of amount of fuel, amount of fuel feeding, and neutron flux distribution. The result of MCNP6 and NEWT module in SCALE show some difference in depletion analysis, but it still seems that they can be used to analyze MSBR. Using these two computer code system, it is possible to analyze various parameters for the MSBR unit cells such as the multiplication factor, breeding ratio, amount of material, total feeding, and neutron flux distribution. Furthermore, the two code systems will be able to be used for analyzing other MSR model or whole core models of MSR.

  13. Clinch River Breeder Reactor Plant steam generator: FEW tube test model post test examination

    International Nuclear Information System (INIS)

    The Steam Generator Few Tube Test (FTT) is part of an extensive testing program being carried out in support of the Clinch River Breeder Reactor Plant (CRBRP) steam generator design. The testing of full-length seven-tube evaporator and three-tube superheater models of the CRBRP design was conducted to provide steady-state thermal/hydraulic performance data to full power per tube and to verify the absence of multi-year endurance problems. The problems encountered with the mechanical features of the FTT model design which led to premature test termination and the results of the post-test examination are described

  14. Reactor shutdown system of prototype fast breeder reactor

    International Nuclear Information System (INIS)

    Full text: The shutdown system of PFBR is designed to assure a very high reliability by employing well known principles of redundancy, diversity and independence. The failure probability of the shutdown system limited to -6/ ry. Salient features of the shutdown system are: Two independent shutdown systems, each of them able to accommodate an additional single failure and made up of a trip system and an associated absorber rod group. Diversity between trip systems, rods and mechanisms. Initiation of SCRAM by two diverse physical parameters of the two shutdown systems for design events leading potentially to unacceptable conditions is the core. The first group of nine rods called control and safety rods (CSR) is used for both shutdown as well as power regulation. The second group consisting of three rods known as diverse safety rods (DSR) is used only for shutdown. Diversity between the two groups is ensured by varying the operating conditions of the electromagnets and the configurations of the mobile parts. The reactivity worth of the absorber rods have been chosen such that each group of rods would ensure cold shutdown on SCRAM even when the most reactive rod of the group fails to drop. Together the two groups ensure a shutdown margin of 5000 pcm. The speed and individual rod worth of the CSR is chosen from operational and safety considerations during reactor start up and raising of power. Required drop time of rods during SCRAM depends on the incident considered. For a severe reactivity incident of 3 $/s this has to be limited to 1s and is ensured by limiting electromagnet response time and facilitating drop by gravity. Design safety limits for core components have been determined and SCRAM parameters have been identified by plant dynamic analysis to restrict the temperatures of core components within the limits. The SCRAM parameters are distributed between the two systems appropriately. Fault tree analysis of the system has been carried out to determine the

  15. Manufacturing of prototype fast breeder reactor components: challenges and achievements

    International Nuclear Information System (INIS)

    In the presentation, three components of 500 MWe Prototype Fast Breeder Reactor (PFBR), viz. grid plate, roof slab and fuel handling systems, are focused, which have been responsible for the considerable delay of the project schedule. The manufacturing challenges of grid plate mainly originated from large number of sleeves resulting in higher self weight and hard facing of large diameter sleeves. Machining of large diameter plates and shell assembly to the required tight tolerances on dimensions, hard facing with nickel based cobalt free hard facing material on continuous, large diameter (6.7 m) annular tracks, heat treatment of large austenitic stainless steel parts at 1050℃ with controlled rates of cooling and heating together with control on temperature gradient across the parts, complex assembly of a large number of parts (∼14900) meeting the important requirements on verticality of sleeve assemblies (Ø0.1 mm) and delicate handling and transportation are truly challenging activities in the manufacturing technology. In case of roof slab, complex manufacturing process, especially welding between the shell and stiffeners caused lamellar tearing problems and extensive testing time. Inclined fuel transfer machine, multiple repairs, heavy weight and testing strategy resulted in long manufacturing and testing time. Some general lessons learnt are also brought out in this presentation. Technology development prior to start of construction is essential for long delivery components. Judicious choice of tolerances, number and location of welds and inspections has to be made. Robust criteria need to be applied for the acceptance of manufacturing deviations and material compositions. Indigenous materials should be used after qualifications of manufacturing process of direct relevance apart from routine standards. From the rich experience gained through the manufacture and erection of reactor assembly components of PFBR, important guidelines and approaches were derived

  16. Status of liquid metal cooled fast breeder reactors

    International Nuclear Information System (INIS)

    This document represents a compilation of the information on the status of fast breeder reactor development. It is intended to provide complete and authoritative information for academic, energy, industrial and planning organizations in the IAEA Member States. The Report also provides extended reference and bibliography lists. A summarized overview of the national programmes of LMFBR development is given in Chapter II. Chapter III on LMFBR experience provides a brief description and purpose of all fast reactors - experimental, demonstration and commercial size - that have been or are planned for construction and operation. Fast reactor physics is dealt with in Chapter IV. Besides the basic facts and definitions of neutronics and the compilation and measurement of nuclear data, a broad range of the calculation methods, codes, and the state of the art is described. In Chapter V, fuels and materials are described. The emphasis is on the design and development experience gained with mixed oxide fuel pins and subassemblies. Structural materials, blanket elements and absorber materials are also discussed. Chaper VI presents a broad overview of the technical and engineering aspects of LMFBR power plants. LMFBR core design is described in detail, followed by the components of the main heat transport system, the refuelling equipment, and auxiliary systems. Chapter VII on safety is a compilation of the current safety design concepts of LMFBRs and new trends in safety criteria and safety goals. The chapter concludes with risk analyses of LMFBR technology. In Chapter VIII, the systems approach has been emphasized in the consideration of the whole LMFBR fuel cycle. Special emphasis is placed on safeguards aspects and the environmental impact of the LMFBR fuel cycle. Chapter IX describes deployment considerations of LMFBRs. Special emphasis is placed on economic aspects of the LMFBR power plant and its related fuel cycle. Finally, Chapter X provides an overall summary and a

  17. Progress report on fast breeder reactor development in Japan

    International Nuclear Information System (INIS)

    In the power increase performance test of the experimental fast reactor ''Joyo'', which was in progress since April, the first stage of the rated thermal output of 50 MW has been accomplished on July 5. Thereafter, the continuous opeation test at 50 MW for 100 hours was performed for the verification of its overall operational performance from August 13 to 16. The safety evaluation for power increase up to 75 MW and 100 MW, which was under way since September, last year, was completed, and the power increase was licensed on September 20. Concerning the design of the prototype fast breeder reactor ''Monju'', the studies on the specifications of the Construction Preliminary Design (2) have been finished. In respect of the analysis and preparation of materials for the Safety Licensing by the Committee, the developments of the analytical codes for rupture propagation in the heat transfer tubes of steam generators and for decay heat have been conducted. In the construction site surveys, the third geological structure survey and beach deformation survey have all ended, while the meteorological and seismic observations, the prediction of the diffusion of drained warm water, the survey of river flow, etc. are now under way. A report on the survey conducted on the construction site in Shiraki was received by the Fukui prefectural government in July, and the copies of a report on the assessment of environmental effect were submitted in August to both the national government and the Fukui prefectural government. The situations of progress of the research and development works on reactor physics, structural components, instrumentation and control, sodium technology, fuel materials, structural materials, safety and steam generators are reported. (Nakai, Y.)

  18. An Evaluation of liquid metal leak detection methods for the Clinch River Breeder Reactor Plant

    Energy Technology Data Exchange (ETDEWEB)

    Morris, C.J.; Doctor, S.R.

    1977-12-01

    This report documents an independent review and evaluation of sodium leak detection methods described in the Clinch River Breeder Reactor Preliminary Safety Analysis Report. Only information in publicly available documents was used in making the assessments.

  19. Fusion breeder studies program: Final report

    International Nuclear Information System (INIS)

    This report is an assessment of technology related to hybrid reactors, especially the Fission-suppressed hybrid. A description of a typical fission-suppressed reactor is given. The economic advantages of the use of a hybrid reactor as part of a fuel cycle center are discussed at length. The inherent safety advantages of the hybrid reactor are analyzed. The report concludes with a proposed timetable for research and development

  20. Fusion breeder studies program: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Berwald, D.H.

    1986-10-17

    This report is an assessment of technology related to hybrid reactors, especially the Fission-suppressed hybrid. A description of a typical fission-suppressed reactor is given. The economic advantages of the use of a hybrid reactor as part of a fuel cycle center are discussed at length. The inherent safety advantages of the hybrid reactor are analyzed. The report concludes with a proposed timetable for research and development. (JDH)

  1. Method of advancing research and development of fast breeder reactors

    International Nuclear Information System (INIS)

    In the long term plan of atomic energy development and utilization, fast breeder reactors are to be developed as the main of the future nuclear power generation in Japan, and when their development is advanced, it has been decided to positively aim at building up the plutonium utilization system using FBRs superior to the uranium utilization system using LWRs. Also it has been decided that the development of FBRs requires to exert incessant efforts for a considerable long period under the proper cooperation system of government and people, and as for its concrete development, hereafter the deliberation is to be carried out in succession by the expert subcommittee on FBR development projects of the Atomic Energy Commission. The subcommittee was founded in May, 1986, to deliberate on the long term promotion measures for FBR development, the measures for promoting the research and development, the examination of the basic specification of a demonstration FBR, the measures for promoting international cooperation, and other important matters. As the results of investigation, the situation around the development of FBRs, the fundamentals at the time of promoting the research and development, the subjects of the research and development and so on are reported. (Kako, I.)

  2. Chemical and spectrochemical production analysis of ThO2 and 233UO2-ThO2 pellets for the light water breeder reactor core for Shippingport (LWBR development program)

    International Nuclear Information System (INIS)

    The Bettis Atomic Power Laboratory has utilized wet chemical, emission spectrochemical, and mass spectrometric analytical techniques for the production analysis of the ThO2 and 233UO2-ThO2 (1 to 6 wt percent 233UO2) pellets for the Light Water Breeder Reactor (LWBR) core for Shippingport. Proof of the fuel breeding concept necessitates measurement of precise and accurate chemical characterization of all fuel pellets before core life. Chemistry's efforts toward this goal are presented in three main sections: (1) general discussions relating the chemical requirements for ThO2 and 233UO2-ThO2 core materials to the analytical capabilities, (2) technical discussions of the chemical and instrumental technology applied for the analysis of aluminum, boron, calcium, carbon, chloride plus bromide, chromium, cobalt, copper, dysprosium, europium, fluoride, gadolinium, iron, magnesium, manganese, mercury, molybdenum, nickel, nitrogen, samarium, silicon, titanium, vanadium, thorium, and uranium (total, trace, and uranium VI), and (3) a formal presentation of the analytical procedures as applied to the LWBR Development Program. (U.S.)

  3. Defect assessment procedure: A french approach for fast breeder reactors

    International Nuclear Information System (INIS)

    As a result of a collaborative effort between Commissariat a l'Energie Atomique, Electricite de France, and NOVATOME to produce and improve rules for fast breeder reactors, RCC-MR, an interim defect assessment procedure is now available in the first draft version (appendix A16). This procedure addresses defects detected during in-service inspection for reactor components operating at moderate or high temperature conditions. Three stages have been considered: initiation, propagation under cyclic loading with or without holdtime and crack instability by ductile and creep rupture. For each of these topics, procedures and rules based on fracture mechanics are proposed. Prediction of initiation is obtained by a simplified method named σd method which relies on the evaluation of the real stress-strain history on a small distance d (d = 0.05 mm for 316L(N) austenitic steel) close to the crack front and material characteristics (limiting stresses) that are available in nuclear codes. This method has been developed for fatigue, creep and creep-fatigue conditions. Defect growth assessment is performed for fatigue and creep-fatigue conditions. For creep-fatigue conditions, fatigue and creep crack growth per cycle are calculated separately and the total crack extension is taken as the sum of the two contributions. Extensive use of simplified method for estimating J (Js method) is made and developed when mechanical and thermal loadings are specified. On the final defect size, assessment may be made in order to avoid crack instability by ductile and creep rupture and collapse load on the remaining. The organization and contents of the present version of this appendix A16 is described. An overview of each specific rule is given

  4. Theory, design, and operation of liquid metal fast breeder reactors, including operational health physics

    Energy Technology Data Exchange (ETDEWEB)

    Adams, S.R.

    1985-10-01

    A comprehensive evaluation was conducted of the radiation protection practices and programs at prototype LMFBRs with long operational experience. Installations evaluated were the Fast Flux Test Facility (FFTF), Richland, Washington; Experimental Breeder Reactor II (EBR-II), Idaho Falls, Idaho; Prototype Fast Reactor (PFR) Dounreay, Scotland; Phenix, Marcoule, France; and Kompakte Natriumgekuhlte Kernreak Toranlange (KNK II), Karlsruhe, Federal Republic of Germany. The evaluation included external and internal exposure control, respiratory protection procedures, radiation surveillance practices, radioactive waste management, and engineering controls for confining radiation contamination. The theory, design, and operating experience at LMFBRs is described. Aspects of LMFBR health physics different from the LWR experience in the United States are identified. Suggestions are made for modifications to the NRC Standard Review Plan based on the differences.

  5. Theory, design, and operation of liquid metal fast breeder reactors, including operational health physics

    International Nuclear Information System (INIS)

    A comprehensive evaluation was conducted of the radiation protection practices and programs at prototype LMFBRs with long operational experience. Installations evaluated were the Fast Flux Test Facility (FFTF), Richland, Washington; Experimental Breeder Reactor II (EBR-II), Idaho Falls, Idaho; Prototype Fast Reactor (PFR) Dounreay, Scotland; Phenix, Marcoule, France; and Kompakte Natriumgekuhlte Kernreak Toranlange (KNK II), Karlsruhe, Federal Republic of Germany. The evaluation included external and internal exposure control, respiratory protection procedures, radiation surveillance practices, radioactive waste management, and engineering controls for confining radiation contamination. The theory, design, and operating experience at LMFBRs is described. Aspects of LMFBR health physics different from the LWR experience in the United States are identified. Suggestions are made for modifications to the NRC Standard Review Plan based on the differences

  6. The present status of the fast breeder reactor industrialization in western Europe

    International Nuclear Information System (INIS)

    The development of the liquid metal fast breeder reactor in Europe started in the mid-fifties, after the successful operation of EBR-1 at ARCO, Idaho, in 1951. A more and more integrated development among the countries of the European Community culminated in 1986 with the beginning to power of the 1200 MWe SUPERPHENIX plant at Creys-Malville, France. The road is now open towards the full industrialization of the liquid metal fast breeder reactor at the moment, in 2005, when the first European thermal neutron power reactor station will have to be decommissioned and replaced. The European programme aims at providing the utilities at that time with a clear choice between thermal neutron reactors and fast breeder reactors, both economical but very different in their use of the limited natural resource that uranium is. (author)

  7. Present status of the fast breeder reactor industrialization in western Europe

    International Nuclear Information System (INIS)

    The development of the liquid metal fast breeder reactor in Europe started in the mid-fifties, after the successful operation of EBR-1 at ARCO, Idaho, in 1951. A more and more integrated development among the countries of the European Community culminated in 1986 with the startup of the 1200 MWe SUPERPHENIX plant at Creys-Malville, France. The road is now open towards the full industrialization of the liquid metal fast breeder reactor at the moment, in 2005, when the first European thermal neutron power reactor station will have to be decommissioned and replaced. The European programme aims at providing the utilities at that time with a clear choice between thermal neutron reactors and fast breeder reactors, both economical but very different in their use of the limited natural resources that uranium

  8. Numerical simulation of sodium pool fires in liquid metal-cooled fast breeder reactor

    International Nuclear Information System (INIS)

    In Liquid Metal-Cooled Fast Breeder Reactor (LMFBR), the leakage of sodium can result in sodium fires. Due to sodium's high chemical reactivity in contact with air and water, sodium fires will lead to an immediate increase of the air temperature and pressure in the containment. This will harm the integrity of the containment. In order to estimate and foresee the sequence of this accident, or to prevent the accident and alleviate the influence of the accident, it is necessary to develop programs to analyze such sodium fire accidents. Based on the work of predecessors, flame sheet model is produced and used to analyze sodium pool fire accidents. Combustion model and heat transfer model are included and expatiated. And the comparison between the analytical and experimental results shows the program is creditable and reasonable. This program is more realistic to simulate the sodium pool fire accidents and can be used for nuclear safety judgement. (authors)

  9. Network Representation of Design Knowledge of Prototype Fast Breeder Reactor

    International Nuclear Information System (INIS)

    A method of design knowledge representation was studied for the Japanese fast breeder reactor Monju, aiming at enhanced understanding of engineering considerations with mutual relations. Taking over design knowledge of Monju to next generation designers/engineers to be in charge of design of future FRs is by no means easy, in contrast with operation and maintenance knowledge which can be acquired in the real plant operation and maintenance. Specifications of the as-is Monju contains only a small part of the entire design knowledge, mainly by two reasons. Firstly, reasons for selecting the as-is specifications can not be understood until reaching proper knowledge source. Secondly, there are many rejected options on the design specifications. Design specifications are selected along with technical dependencies among a huge number and diversified specification items. Decisions design are made basically along with these dependencies which can hardly be traced in the currently available database or document libraries. Reasons for the rejections of options need to be profoundly understood, because those are not certainly due to technical inferiority. Some of rejected options can be worth reconsidering in the future, possibly by technical advances in materials, high-precision prediction software tools, rationalized standards/code, etc. The authors propose a new design knowledge representation approach based on networking of knowledge nodes along with the mutual dependencies. A prototype software has been developed and a basic performance test was made to visualize the dependency network. An additional function to enable design case studies on hypothetical adoptions of rejected options is now under consideration. (author)

  10. Development of high nitrogen electrodes for fast breeder reactor applications

    International Nuclear Information System (INIS)

    Austenitic stainless steels of AISI type 316 (316 SS) and its variants are used extensively as structural material for the components of fast reactors operating at temperature up to 823 K. SS 316LN has been chosen as the major structural material for the construction of Prototype Fast Breeder Reactor (PFBR) with a targeted service life of 40 years. To reduce the risk of sensitization in SS 316LN, the carbon content has been reduced to less than 0.03 wt%, and the nitrogen content has been specified as 0.08 wt% to compensate the loss in strength due to the reduced carbon content. An improved version of this alloy with nitrogen content of 0.14 wt% in a frilly austenite matrix has been developed for the future FBRs, to enhance the service life of the structural components up to 60 years. Indigenously developed modified E3 16-1 5 electrodes were used for the fabrication of PFBR components to enhance the structural reliability of the components. The modifications from AWS/ASME SFA 5.4 include stringent composition limits, narrow range of ferrite content, and impact toughness after aging at 1023K for 100h, tensile properties at elevated (service) temperatures and intergranular corrosion (IGC) test as per ASTM A262 Practice E. Since the improved version alloy is rich in nitrogen content than the existing alloy, it has become necessary to develop a welding consumable with reasonably good weldability that is suitable for the fabrication of future FBR components. At present there are no commercially available welding consumables to weld these steels and the development is under way. In this work, a matching consumable methodology was adopted to develop the welding consumable. However, as per specification targeting the chemistry, solidification mode and delta ferrite was challenging, since the solidification mode of the weld metal shifts to fully austenitic region due to dilution of nitrogen from the base metal, which may increase the risk of hot cracking susceptibility

  11. Data management for the Clinch River Breeder Reactor Plant Project by use of document status and hold systems

    International Nuclear Information System (INIS)

    This paper describes the development, framework, and scope of the Document Status System and the Document Hold System for the Clinch River Breeder Reactor Plant Project. It shows how data are generated at five locations and transmitted to a central computer for processing and storage. The resulting computerized data bank provides reports needed to perform day-to-day management and engineering planning. Those reports also partially satisfy the requirements of the Project's Quality Assurance Program

  12. Fast breeder reactors insertion in a D2O - natural U nuclear power plants park

    International Nuclear Information System (INIS)

    A model for the evolution of Argentine's installed nuclear power for the next 40 years is presented. The consequences of fast breeder reactors' introduction are studied in both autarchic Pu cycle and a limited reprocessing system. The passage of a reactor park like the national, of natural U - heavy water to one of fast breeder reactors, can only be obtained in a very long term due, fundamentally, to the need of Pu produced for those to feed the last ones. (M.E.L.)

  13. On the development of fast breeder reactors and the use of thorium in Brazil

    International Nuclear Information System (INIS)

    This work presents a discussion on the possibility of construction of fast breeder reactors in Brazil. It is specially concerned with the use of thorium which is abundant in our country. The main advantages of this projects are: develop fuel and reactor technology in Brazil, increase thorium research, demonstrate the safety of LMFBR and promote its public acceptance. (A.C.A.S.)

  14. An option for the Brazilian nuclear project: necessity of fast breeder reactors and core design for an experimental fast reactor

    International Nuclear Information System (INIS)

    Aiming to assure the continued utilization of fission energy, the development of fast breeder reactors (FBRs) is a necessity. Binary fueled LMFBRs are proposed, as the best type for the Brazilian nuclear system in the future. The inherent safety characteristics are superior to current fast breeder reactors and an efficient utilization of thorium can be realized. The construction and operation of an experimental fast reactor is the first step and a basic tool for the development of FBRs technologies. A serie of core design for an 90 MW FBR is studied and the possible options and sizes of the main parameters are identified. (E.G.)

  15. IAEA note on multi-national fuel cycle centres as related to fast breeder reactors

    International Nuclear Information System (INIS)

    The significant aspects of associating fast breeder reactor fuel cycles with the concept of regional fuel cycle centres, as studied earlier by the IAEA, are identified. The results of the RFCC Study Project are presented, and how in particular non-proliferation and safeguards, radioactive waste management and economic considerations would be effected by inclusion of fast breeder reactor fuel cycle facilities and possibly fast breeder reactors as well in such centres, are discussed. The current effort of the IAEA to develop a computer programme which models the material flows in the nuclear fuel cycle which could be applied to the analysis of alternative siting strategies for FBR and its fuel cycle facilities is discussed

  16. Clinch River Breeder Reactor Plant Steam Generator Few Tube Test model post-test examination

    International Nuclear Information System (INIS)

    The Steam Generator Few Tube Test (FTT) was part of an extensive testing program carried out in support of the Clinch River Breeder Reactor Plant (CRBRP) steam generator design. The testing of full-length seven-tube evaporator and three-tube superheater models of the CRBRP design was conducted to provide steady-state thermal/hydraulic performance data to full power per tube and to verify the absence of multi-year endurance problems. This paper describes the problems encountered with the mechanical features of the FTT model design which led to premature test termination, and the results of the post-test examination. Conditions of tube bowing and significant tube and tube support gouging was observed. An interpretation of the visual and metallurgical observations is also presented. The CRBRP steam generator has undergone design evaluations to resolve observed deficiences found in the FFTM

  17. Operation and maintenance experience with control rod and their drive mechanisms of fast breeder test reactor

    International Nuclear Information System (INIS)

    This paper explains the functional and construction features of Control Rod Drive Mechanism (CRDM) and control rod used in Fast Breeder Test Reactor (FBTR) which is a 40 MWt loop type sodium cooled fast reactor. It discusses all safety related incidents and failures encountered during its service in reactor, the solutions evolved and modifications carried out to prevent recurrence. It also details the maintenance activities and periodical surveillance carried out. The results of a reliability analysis done are also discussed. (author)

  18. Plutonium breeding in liquid-metal fast breeder reactors and light water reactors

    International Nuclear Information System (INIS)

    The possibilities of breeding in liquid-metal fast breeder reactors (LMFBRs) and light water reactors (LWRs) are compared in two ways. The feasibility of breeding has been demonstrated in the Phenix reactor with a measured gain of 0.14. The gain in Superphenix will amount to about0.20. The studies show that while maintaining the performance of commercial reactors their breeding gain can be further increased either by the concept of heterogeneous cores or by using carbide or nitride fuel (breeding gain about0.35). Recently, the old idea of breeding in advanced pressurized water reactors (PWRs) has been taken up again with the objective of attaining a gain of 0.05. Unfortunately, these objectives had to be limited to a conversion ratio of 0.9 for safety reasons, and it is not certain whether operation will be rewarding economically. The strategy of substituting PWRs is examined using the French example. By gradually introducing LMFBRs, the cumulated uranium supplies in France can be kept within reasonable limits, which means that they attain three to four times the home resources. This is not possible with advanced LWRs, which can be considered only as a possible backup solution for plutonium recycling into PWRs

  19. Status of national programmes on fast breeder reactors. Eighteenth annual meeting, Vienna, Austria, 16-19 April 1985

    International Nuclear Information System (INIS)

    The Eighteenth Annual Meeting on the Status of National Programmes in Member States of the IAEA on Fast Breeder Reactors had been held in April 1985. The representatives of the Member States and international organizations reported status and activities in the field of fast breeder reactors development and operation. A separate abstract was prepared for each of the 12 presentations of the meeting

  20. Network representation of design knowledge of prototype Fast Breeder Reactor

    International Nuclear Information System (INIS)

    A method of design knowledge representation was studied for the Japanese fast breeder reactor Monju, aiming at enhanced understanding of engineering considerations with mutual relations. Taking over design knowledge of Monju to next generation designers/engineers to be in charge of design of future FRs is by no means easy, in contrast with operation and maintenance knowledge which can be acquired in the real plant operation and maintenance. Specifications of the as-is Monju contains only a small part of the entire design knowledge, mainly by two reasons. Firstly, reasons for selecting the as-is specifications can not be understood until reaching proper knowledge source. Secondly, there are many passed-over options on the design specifications. Reasons for passing-over these options are not always technical inferiority. A large part of the current specifications are selected because the worst possible technical value can be foreseeable or guaranteed to be acceptable within limited R and D period and resource, not because the expected value is estimated to be the lower. In other words, in the future where new materials with improved properties, faster and more accurate analysis/prediction methods, rationalized technical standards or regulatory requirements, and/or some other environment for thorough comparison among specification options are available, these passed-over options are likely to be worth reconsidering. There are a huge number of technical documents on diversified engineering studies, such as calculation of maximum possible temperature gradient of important structures, necessary sodium flow rate in particular sub-assemblies, etc. for validation of each decision making in design. A large part of these documents are scanned and stored in a data base with each catalogue data for electronic browse. The authors propose a network representation of these items of design decision making, where the items are mutually connected by directed arcs, where nodes stand

  1. Method of locating a leaking fuel element in a fast breeder power reactor

    Energy Technology Data Exchange (ETDEWEB)

    Honekamp, John R. (Downers Grove, IL); Fryer, Richard M. (Idaho Falls, ID)

    1978-01-01

    Leaking fuel elements in a fast reactor are identified by measuring the ratio of .sup.134 Xe to .sup.133 Xe in the reactor cover gas following detection of a fuel element leak, this ratio being indicative of the power and burnup of the failed fuel element. This procedure can be used to identify leaking fuel elements in a power breeder reactor while continuing operation of the reactor since the ratio measured is that of the gases stored in the plenum of the failed fuel element. Thus, use of a cleanup system for the cover gas makes it possible to identify sequentially a multiplicity of leaking fuel elements without shutting the reactor down.

  2. Method of locating a leaking fuel element in a fast breeder power reactor

    Energy Technology Data Exchange (ETDEWEB)

    Honekamp, J.R.; Fryer, R.M.

    1978-03-21

    Leaking fuel elements in a fast reactor are identified by measuring the ratio of /sup 134/Xe to /sup 133/Xe in the reactor cover gas following detection of a fuel element leak, this ratio being indicative of the power and burnup of the failed fuel element. This procedure can be used to identify leaking fuel elements in a power breeder reactor while continuing operation of the reactor since the ratio measured is that of the gases stored in the plenum of the failed fuel element. Thus, use of a cleanup system for the cover gas makes it possible to identify sequentially a multiplicity of leaking fuel elements without shutting the reactor down.

  3. Evaluation of symbiotic energy system between gas-cooled fast breeder reactor (GCFR) and multi-purpose very high temperature reactor (VHTR), (4)

    International Nuclear Information System (INIS)

    The conceptual design study of 1000 MWe gas-cooled fast breeder reactor (GCFR), which is used in the GCFR-VHTR symbiotic energy system, has been performed. In this report, the transient response of the GCFR core to accident events has been analyzed and safety performance of the 1000 MWe GCFR has been evaluated considering the analyses. A depressurization accident caused by failure of a primary coolant system and a reactivity insertion accident due to withdrawal of a control rod have been analyzed using nuclear and thermo-hydraulic coupled program MR-X developed for kinetics analysis of gas-cooled fast breeder reactors. The maximum fuel and cladding temperatures are most important problem to be analysed during a trangient of a gas-cooled fast breeder reactors. The analyses show that reliable reactor shutdown and emergency cooling systems are most important to achieve successful cold shutdown well before leading to core damage and also that no severe failures of fuel pin and cladding occures by working above mentioned safety systems well during the accidents. (author)

  4. Status of the fast breeder reactor development in the Federal Republic of Germany, Belgium and the Netherlands

    International Nuclear Information System (INIS)

    In 1967 and 1968 the Federal Republic of Germany, the Kingdom of Belgium and the Kingdom of the Netherlands (''DeBeNe'') agreed to develop, in a joint program, breeder reactors to the point of commercial maturity. The following research organizations take part in this effort: Kernforschungszentrum Karlsruhe (KfK); INTERATOM, Bergisch Gladbach; ALKEM, Wolfgang near Hanau; SCK/CEN, Mol; Belgonucleaire, Brussels; ECN, Petten; TNO, Apeldoorn; NERATOOM, The Hague. The three German institutions mentioned above have been interrelated since 1977 by the Entwicklungsgemeinschaft (EG) Schneller Brueter. Between KfK, INTERATOM, and the French Commissariat a l'Energie Atomique contracts were concluded in 1977 about close cooperation in the Fast Breeder field, with association of the Belgian and Dutch partners. The results of research and development activities carried out by the DeBeNe partners in 1981 have been compiled in this report. The report begins with a short survey of the fast reactor plants, followed by an R and D summary. The bulk of the report gives more detailed information about those plants and about results reported by the Working Groups of the R and D Program Working Committee of the Fast Breeder Project. In an additional chapter a survey is given of international cooperation. (author)

  5. Recommendations concerning models and parameters best suited to breeder reactor environmental radiological assessments

    International Nuclear Information System (INIS)

    Recommendations are presented concerning the models and parameters best suited for assessing the impact of radionuclide releases to the environment by breeder reactor facilities. These recommendations are based on the model and parameter evaluations performed during this project to date. Seven different areas are covered in separate sections

  6. Engineering review of the core support structure of the Gas Cooled Fast Breeder Reactor

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-09-01

    The review of the core support structure of the gas cooled fast breeder reactor (GCFR) covered such areas as the design criteria, the design and analysis of the concepts, the development plan, and the projected manufacturing costs. Recommendations are provided to establish a basis for future work on the GCFR core support structure.

  7. Recommendations concerning models and parameters best suited to breeder reactor environmental radiological assessments

    Energy Technology Data Exchange (ETDEWEB)

    Miller, C.W.; Baes, C.F. III; Dunning, D.E. Jr.

    1980-05-01

    Recommendations are presented concerning the models and parameters best suited for assessing the impact of radionuclide releases to the environment by breeder reactor facilities. These recommendations are based on the model and parameter evaluations performed during this project to date. Seven different areas are covered in separate sections.

  8. ORIGEN2 model and results for the Clinch River Breeder Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Croff, A G; Bjerke, M A

    1982-06-01

    Reactor physics calculations and literature information acquisition have led to the development of a Clinch River Breeder Reactor (CRBR) model for the ORIGEN2 computer code. The model is based on cross sections taken directly from physics codes. Details are presented concerning the physical description of the fuel assemblies, the fuel management scheme, irradiation parameters, and initial material compositions. The ORIGEN2 model for the CRBR has been implemented, resulting in the production of graphical and tabular characteristics (radioactivity, thermal power, and toxicity) of CRBR spent fuel, high-level waste, and fuel-assembly structural material waste as a function of decay time. Characteristics for pressurized water reactors (PWRs), commercial liquid-metal fast breeder reactors (LMFBRs), and the Fast Flux Test Facility (FFTF) have also been included in this report for comparison with the CRBR data.

  9. Status of National Programmes on Fast Breeder Reactors. International Working Group on Fast Reactors Twenty-First Annual Meeting, Seattle, USA, 9-12 May 1988

    International Nuclear Information System (INIS)

    The following papers on the status of national programmes on fast breeder reactors are presented in this report: Fast breeder reactor development in France during 1987; Status of fast breeder reactor development in the Federal Republic of Germany, Belgium and the Netherlands; A review of the Indian fast reactor programme; A review of the Italian fast reactor programme; A review of the fast reactor programme in Japan; Status of fast reactor activities in the USSR; A review of the United Kingdom fast reactor programme; Status of liquid metal reactor development in the United States of America; Review of activities of the Commission of European Communities relating to fast reactors in 1987; European co-operation in the field of fast reactor research and development — 1987 progress report; A review of fast reactor activities in Switzerland

  10. Overview of pool hydraulic design of Indian prototype fast breeder reactor

    Indian Academy of Sciences (India)

    K Velusamy; P Chellapandi; S C Chetal; Baldev Raj

    2010-04-01

    Thermal hydraulics plays an important role in the design of liquid metal cooled fast breeder reactor components, where thermal loads are dominant. Detailed thermal hydraulic investigations of reactor components considering multi-physics heat transfer are essential for choosing optimum designs among the various possibilities. Pool hydraulics is multi-dimensional in nature and simple one-dimensional treatment for the same is often inadequate. Computational Fluid Dynamics (CFD) plays a critical role in the design of pool type reactors and becomes an increasingly popular tool, thanks to the advancements in computing technology. In this paper, thermal hydraulic characteristics of a fast breeder reactor, design limits and challenging thermal hydraulic investigations carried out towards successful design of Indian Prototype Fast Breeder Reactor (PFBR) that is under construction, are highlighted. Special attention is paid to phenomena like thermal stratification, thermal stripping, gas entrainment, inter-wrapper flow in decay heat removal and multiphysics cellular convection. The issues in these phenomena and the design solutions to address them satisfactorily are elaborated. Experiments performed for special phenomena, which are not amenable for CFD treatment and experiments carried out for validation of the computer codes have also been described.

  11. Application of hafnium hydride control rod to large sodium cooled fast breeder reactor

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, Kazumi, E-mail: kazumi_ikeda@mfbr.mhi.co.jp [Mitsubishi FBR Systems, Inc., 34-17, Jingumae 2-Chome, Shibuya-ku, Tokyo 150-0001 (Japan); Moriwaki, Hiroyuki, E-mail: hiroyuki_moriwaki@mfbr.mhi.co.jp [Mitsubishi FBR Systems, Inc., 34-17, Jingumae 2-Chome, Shibuya-ku, Tokyo 150-0001 (Japan); Ohkubo, Yoshiyuki, E-mail: yoshiyuki_okubo@mfbr.mhi.co.jp [Mitsubishi FBR Systems, Inc., 34-17, Jingumae 2-Chome, Shibuya-ku, Tokyo 150-0001 (Japan); Iwasaki, Tomohiko, E-mail: tomohiko.iwasaki@qse.tohoku.ac.jp [Department of Quantum Science and Energy Engineering, Tohoku University, Aoba, Aramaki, Aoba-ku, Sendai-shi, Miyagi-ken 980-8579 (Japan); Konashi, Kenji, E-mail: konashi@imr.tohoku.ac.jp [Institute for Materials Research, Tohoku University, Narita-cho, Oarai-machi, Higashi-Ibaraki-gun, Ibaraki-ken 311-1313 (Japan)

    2014-10-15

    Highlights: • Application of hafnium hydride control rod to large sodium cooled fast breeder reactor. • This paper treats application of an innovative hafnium hydride control rod to a large sodium cooled fast breeder reactor. • Hydrogen absorption triples the reactivity worth by neutron spectrum shift at H/Hf ratio of 1.3. • Lifetime of the control rod quadruples because produced daughters of hafnium isotopes are absorbers. • Nuclear and thermal hydraulic characteristics of the reactor are as good as or better than B-10 enriched boron carbide. - Abstract: This study treats the feasibility of long-lived hafnium hydride control rod in a large sodium-cooled fast breeder reactor by nuclear and thermal analyses. According to the nuclear calculations, it is found that hydrogen absorption of hafnium triples the reactivity by the neutron spectrum shift at the H/Hf ratio of 1.3, and a hafnium transmutation mechanism that produced daughters are absorbers quadruples the lifetime due to a low incineration rate of absorbing nuclides under irradiation. That is to say, the control rod can function well for a long time because an irradiation of 2400 EFPD reduces the reactivity by only 4%. The calculation also reveals that the hafnium hydride control rod can apply to the reactor in that nuclear and thermal characteristics become as good as or better than 80% B-10 enriched boron carbide. For example, the maximum linear heat rate becomes 3% lower. Owing to the better power distribution, the required flow rate decreases approximately by 1%. Consequently, it is concluded on desk analyses that the long lived hafnium hydride control rod is feasible in the large sodium-cooled fast breeder reactor.

  12. World energy resources, demand and supply of energy, and the prospects for the fast breeder reactor

    International Nuclear Information System (INIS)

    In the past it was taken for granted that the prime role of fast breeder reactors was to complement light water reactors, mainly because of their similar and compatible fuel cycles. In particular, the plutonium converted in LWRs is most intelligently disposed of and used in FBRs. Evaluation of the time horizon of such reactor strategies generally extended only to the year 2000. It is important to realize, however, that the salient task in the breeder field after 2000 - besides electricity generation - will be to substitute for conventional ''cheap'' oil. Electricity today makes up only 10% to 12% of the total secondary energy, while liquids essentially command up to about 50%. Thus the future application of the FBR technology will have to be geared more to the production of a liquid secondary energy carrier than to electricity. A new yardstick for all these considerations is the strongly rising energy prices. They may double, for example, leading to an oil price of US 24/bbl. Under these circumstances it is prudent to generalize the scope for future fast breeders. The key element of such a new fast breeder strategy would be the production of hydrogen by electrolysis or thermolysis or a combination of both. For example, methanol synthesized from hydrogen and residual fossil fuels would thus become economically attractive. The FBR breeding gain, on the other hand, would be used for the continued supply of LWRs generating electricity. The paper identifies order-of-magnitude considerations most important for such a fast breeder application against a global energy demand scenario for the year 2030. (author)

  13. Methodical study of cost-benefit analyses of the liquid metal fast breeder reactor

    International Nuclear Information System (INIS)

    Six American cost-benefit analyses (CBA) of nuclear energy and, in particular, of the Liquid Metal Fast Breeder Reactor (LMFBR) were analysed under the aspect of their methodical difficulties. Two different methodical approaches can be discerned which are related to two completely different applications, according to which the advantages and disadvantages of the breeder reactor are estimated in line with the basic concept of cost-benefit analysis. The analytical methods used to justify the continuation of the breeder-related research programme reveal that the specific energy-related technological and economic conditions of the geographic region considered have to be taken into account. The results of a CBA performed for the USA can therefore not be transferred to the Federal Republic of Germany. Due to the in part strongly differing quantitative results the analyses reviewed do not suggest a clear and final decision in favour of the continuation of the American LMFBR research programme to the extent envisaged. In addition, neither by a positive nor by a negative overall result of the analysis can it be concluded that no other advanced electricity generating technology would have a more favourable cost-benefit ratio, or that the breeder-related research activities, which have been pursued for several years already, should be discontinued. (orig.)

  14. The Last Twenty Years of Experience with Fast Breeder Reactors: Lessons Learnt and Perspectives

    International Nuclear Information System (INIS)

    India has made significant achievements in the design and development of sodium cooled fast breeder reactors over the last twenty years. Attaining a maximum burnup of 165 GW.d/t for the plutonium-rich carbide fuel without any cladding failure, coupled with excellent performance of sodium components, including primary pumps, heat exchangers and steam generators over the last 24 years, reprocessing of carbide fuel with a burnup of 150 GW.d/t and engineering tests performed for validating the plant dynamics computer codes, are the achievements from the successful operation of the 40 MW(th) capacity loop type fast breeder test reactor. Indigenous design of the 500 MW(e) Prototype Fast Breeder Reactor (PFBR), executing high quality multidisciplinary R and D and successful manufacturing and erection of large dimensioned thin walled shell structures are the achievements in PFBR development. These achievements, apart from providing confidence in the PFBR project, are instrumental for the design of innovative future reactors. National and international collaboration established with R and D establishments and academic institutions would go a long way towards helping India to attain world leadership by 2020. (author)

  15. Gas core reactors for actinide transmutation and breeder applications. Annual report

    International Nuclear Information System (INIS)

    This work consists of design power plant studies for four types of reactor systems: uranium plasma core breeder, uranium plasma core actinide transmuter, UF6 breeder and UF6 actinide transmuter. The plasma core systems can be coupled to MHD generators to obtain high efficiency electrical power generation. A 1074 MWt UF6 breeder reactor was designed with a breeding ratio of 1.002 to guard against diversion of fuel. Using molten salt technology and a superheated steam cycle, an efficiency of 39.2% was obtained for the plant and the U233 inventory in the core and heat exchangers was limited to 105 Kg. It was found that the UF6 reactor can produce high fluxes (10 to the 14th power n/sq cm-sec) necessary for efficient burnup of actinide. However, the buildup of fissile isotopes posed severe heat transfer problems. Therefore, the flux in the actinide region must be decreased with time. Consequently, only beginning-of-life conditions were considered for the power plant design. A 577 MWt UF6 actinide transmutation reactor power plant was designed to operate with 39.3% efficiency and 102 Kg of U233 in the core and heat exchanger for beginning-of-life conditions

  16. Fast breeder reactor reference system classification for the ENEA data bank

    International Nuclear Information System (INIS)

    This report contains the Reference System Classification (RSC) of fast breeder reactors: it provides a functional system breakdown of the reactor. For each system the following important characteristics are reported: the main function, the mode of operation, its location in the reactor, the main interface system, its main components and the component working environment (fluid and/or atmosphere type). The RSC represent a basic step in organizing the ENEA data bank for the registration and processing of reliability data on typical fast reactor components; it provides a functional component breakdown and represent a plant-unique identification in the process of omogenization of event-data coming from different reactors. In this report it was tried to take into account different generations of nuclear power plants, different plant layouts and solutions: in particular loop and pool reactors are separately treated

  17. In-reactor experiments in fast breeder test reactor for assessment of core structural materials

    International Nuclear Information System (INIS)

    Fast Breeder Test Reactor (FBTR) at Indira Gandhi Centre for Atomic Research (IGCAR), Kalpakkam, India is a sodium cooled reactor with neutron flux level of the order of 1015 n/cm2/s and temperature of coolant in the range of 650-790K (380-520oC). This reactor is being used as a test bed for the development of fuel and structural materials required for Indian Fast Reactor Programme. FBTR is also used as a test facility to carry out accelerated irradiation tests on thermal reactor structural materials. In-reactor experiments on core structural materials are being carried out by subjecting prefabricated specimens to desired conditions of temperature and neutron fluence levels in FBTR. Non-instrumented irradiation capsules that can be loaded at any location of FBTR core are used for the experiments. Pressurised capsules of zirconium alloys have been developed and subjected to irradiation in FBTR to determine the irradiation creep rate of indigenously developed zirconium alloys (Zircaloy-2 and Zr-2.5%Nb alloy) for life assessment of pressure tubes of Indian Pressurised Heavy Water Reactors (PHWRs). Technology development of pressurised capsules was carried out at IGCAR. These pressurised capsules were filled with argon and a small fraction of helium at a high pressure (5.0-6.5 MPa at room temperature) in such a way that the target stresses were attained in the walls of the pressurised capsules at the desired temperature of irradiation in the reactor. FBTR was operated at a low power of 8 MWt during this irradiation campaign to have an inlet temperature of about 579 K (306oC) which was close to the temperature of pressure tubes at full power in PHWR. Irradiation of thirty pressurised capsules was carried out in FBTR using six irradiation capsules for different durations (upto 79 days). The fluence levels attained by the pressurised capsules were up to 1.1 x 1021 n/cm2 (E> 1 MeV) at temperatures of 579 to 592 K. Post-irradiation increase in diameter of the pressurised

  18. Status of the fast breeder reactor technology in China

    International Nuclear Information System (INIS)

    According to the Chinese long-term energy strategy the FBR development is strongly supported. In the near term nuclear programme it is intended to build the experimental First Fast Reactor (FFR) in the year 2000. Design work is in progress. (author). 1 ref., 6 figs, 8 tabs

  19. Applicability of three dimensional diffusion theory programmes based on coarse mesh methods to calculating nuclear characteristics of fast breeder reactors

    International Nuclear Information System (INIS)

    Hexagonal coarse mesh methods in three dimensional diffusion theory programme have been examined for calculating in detail nuclear characteristics of fast breeder reactors composed of hexagonal fuel assemblies, comparing with more accurate triangular fine mesh method. The fast breeder reactors considered here are LMFBRs with different core configurations including heterogeneous core and GCFRs in different burnup states. The nuclear characteristics investigated in the comparative study are effective multiplication factor, power and neutron flux distributions, breeding ratio, reactivity effects and control rod reactivity worth. The comparative study indicates that the conventional coarse mesh method is not adeguate to detailed evaluation on nuclear characteristics of fast breeder reactors, and that the improved coarse mesh method developed by T. Takeda et al. is very useful for this purpose, though some problems exists in evaluation of power distribution and breeding ratio of the extremely composite fast breeder reactors, such as the radially heterogeneous core LMFBR. (author)

  20. Liquid-metal pumps for large-scale breeder-reactor plant (prototype pump)

    Energy Technology Data Exchange (ETDEWEB)

    Lindsay, M. (comp.)

    1976-07-01

    This report presents the recommended pump design for use in Large Scale Liquid Metal Fast Breeder Reactor plants. The base design for the pump will circulate 127,000 GPM of liquid sodium at temperatures up to 850/sup 0/F and with a total discharge head at the design point of 500 feet Na with an impeller that is 40 feet below the sodium seal. The pump design is predicated on developing an impeller design which will have a suction specific speed (S/sub n/) of about 20,000 with 20 feet NPSH available, which will result in a pump speed of 530 RPM at design conditions. The design is based on the technology developed in the design and fabrication of FFTF pumps, the design efforts for the Clinch River Breeder Reactor Pump design study and other technology.

  1. Internal fluid flow management analysis for Clinch River Breeder Reactor Plant sodium pumps

    International Nuclear Information System (INIS)

    The Clinch River Breeder Reactor Plant (CRBRP) sodium pumps are currently being designed and the prototype unit is being fabricated. In the design of these large-scale pumps for elevated temperature Liquid Metal Fast Breeder Reactor (LMFBR) service, one major design consideration is the response of the critical parts to severe thermal transients. A detailed internal fluid flow distribution analysis has been performed using a computer code HAFMAT, which solves a network of fluid flow paths. The results of the analytical approach are then compared to the test data obtained on a half-scale pump model which was tested in water. The details are presented of pump internal hydraulic analysis, and test and evaluation of the half-scale model test results

  2. Tube sheet structural analysis of intermediate heat exchanger for fast breeder reactor 'Monju'

    International Nuclear Information System (INIS)

    The Prototype Fast Breeder Reactor 'Monju' is the first power generating fast breeder reactor in Japan. We have been designing the components of the plant for manufacturing. Among these is the intermediate heat exchanger (IHX) which exchanges heat between primary and secondary sodium loop. The tube sheet of IHX (shell to ligament junction) is a difficult area from the view point of structural strength design under elevated temperature. To validate the structural integrity of tube sheet we performed the series of inelastic analysis and tube sheet thermal shock test using test pieces and half scale model of actual design. The results of inelastic analyses showed there is little progressive deformation around shell to ligament structural discontinuous junction. Furthermore, thermal shock tests showed no increase of an accumulative deformation. By these analyses and experiments, structural reliability of tube sheet could be shown. (author)

  3. Seismic parametric studies in a large scale prototype breeder reactor plant

    International Nuclear Information System (INIS)

    Seismic parametric studies were conducted for a large scale prototype breeder reactor plant (135C MW). The effects of plant configuration, soil stiffness and deep embedment were evaluated. Nuclear island interconnected structures on a common foundation mat with a symmetrical arrangement resulted in lower seismic responses. All other conditions being equal, soft sites are preferable to stiff sites. Deep embedment of the nuclear island could, in certain sites, result in a reduction of seismic responses. (orig.)

  4. Conceptual design of the Clinch River Breeder Reactor spent-fuel shipping cask

    International Nuclear Information System (INIS)

    Details of a baseline conceptual design of a spent fuel shipping cask for the Clinch River Breeder Reactor (CRBR) are presented including an assessment of shielding, structural, thermal, fabrication and cask/plant interfacing problems. A basis for continued cask development and for new technological development is established. Alternates to the baseline design are briefly presented. Estimates of development schedules, cask utilization and cost schedules, and of personnel dose commitments during CRBR in-plant handling of the cask are also presented

  5. Application of mass-predictions to isotope-abundances in breeder-reactor cores

    CERN Document Server

    Kirchner, G

    1981-01-01

    The decay-heat and isotope composition of breeder reactor-cores is calculated at normal shut-down, and a core disintegration event. Using the ORIGEN-code, the influence of the most neutron-rich fission-yield nuclei is studied. Their abundances depend on the assumption about the nuclear data (mass and half-lives). The total decay-heat is not changed from any technical viewpoint. (15 refs).

  6. Research and developments on nondestructive testing in fabrications of fast breeder reactor structural components in Japan

    International Nuclear Information System (INIS)

    Research and developments (R and D) have been conducted on the nondestructive testing techniques necessary for the construction of fast breeder reactor (FBR). Radiographic tests have been made on tube-tube plate welds and small-diameter tube welds, etc. Ultrasonic tests have been conducted on austenitic stainless steel welds. In the penetrant tests and magnetic particle tests, the investigations have been performed on the effects of various test factors on the test results

  7. Application of mass-predictions to isotope-abundances in breeder-reactor cores

    International Nuclear Information System (INIS)

    The decay-heat and isotope composition of breeder reactor-cores is calculated at normal shut-down, and a core disintegration event. Using the ORIGRN-code, the influence of the most neutron-rich fission-yield nuclei is studied. Their abundances depend on the assumption about the nuclear data (mass and half-lives). The total decay-heat is not changed from any technically view-point. (orig.)

  8. Thermal insulation system design and fabrication specification (nuclear) for the Clinch River Breeder Reactor plant

    Energy Technology Data Exchange (ETDEWEB)

    1978-07-21

    This specification defines the design, analysis, fabrication, testing, shipping, and quality requirements of the Insulation System for the Clinch River Breeder Reactor Plant (CRBRP), near Oak Ridge, Tennessee. The Insulation System includes all supports, convection barriers, jacketing, insulation, penetrations, fasteners, or other insulation support material or devices required to insulate the piping and equipment cryogenic and other special applications excluded. Site storage, handling and installation of the Insulation System are under the cognizance of the Purchaser.

  9. Present day design challenges exemplified by the Clinch River Breeder Reactor Plant

    International Nuclear Information System (INIS)

    The present day design challenges faced by the Clinch River Breeder Reactor Plant engineer result from two causes. The first cause is aspiration to achieve a design that will operate at conditions which are desirable for future LMFBRs in order for them to achieve low power costs and good breeding. The second cause is the licensing impact. Although licensing the CRBRP won't eliminate future licensing effort, many licensing questions will have been resolved and precedents set for the future LMFBR industry

  10. Status of national programmes on fast breeder reactors. Nineteenth annual meeting, Kalpakkam, India, 11-14 March 1986

    International Nuclear Information System (INIS)

    The Nineteenth Annual Meeting on the Status of National Programmes in Member States of the IAEA on Fast Breeder Reactors had been held in March 1986. The representatives of the Member States and international organizations reported status and activities in the field of fast breeder reactors development and operation. A report on uranium supply and demand was also presented by the NEA/OECD. A separate abstract was prepared for each of the 11 presentations of the meeting

  11. Physics calculations for the Clinch River Breeder Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kalimullah; Kier, P.H.; Hummel, H.H.

    1977-06-01

    Calculations of distributions of power and sodium void reactivity, unvoided and voided Doppler coefficients and steel and fuel worths have been performed using diffusion theory and first-order perturbation theory for the LWR discharge Pu-fueled CRBR at BOL, the FFTF-grade Pu-fueled CRBR at BOL and for the beginning and end of equilibrium cycle of the LWR-Pu-fueled CRBR. The results of the burnup and breeding ratio calculations performed for obtaining the reactor compositions during the equilibrium cycle are also reported. Effects of sodium and steel contents on the distributions of sodium void reactivity and steel worth have also been studied. Errors and uncertainties in the reactivity coefficients due to cross-sections and the two-dimensional geometric representations of the reactor used in the calculations have also been estimated. Comparisons of the results with those in the CRBR PSAR are also discussed.

  12. Conceptual design of a pool type molten salt breeder reactor

    International Nuclear Information System (INIS)

    The renewed interest in molten salt coolant technology is backed by the 50 years history of molten salt nuclear technology development, mainly in Oak Ridge National Laboratory (ORNL). In Indian context MSBR is found to be one of the options for sustainable nuclear energy generation, especially in the third stage of the nuclear programme. The system can be operated at high temperature which makes high efficiency power conversion and efficient hydrogen generation through thermo-chemical reactions possible. At present development is in progress in BARC on two molten salt reactor concepts, one is pool type and the other is loop type. Here the design of pool type concept with 850MWe power is described. The core is designed to operate in the fast spectrum region so the conversion of 233U breeding is possible from thorium. Preliminary thermal hydraulic analysis is carried out with LiF-ThF4-UF4 as the primary fuel and coolant. The blanket material is also a molten salt, LiF-ThF4. Reactor physics calculations are also carried out for the feasibility studies of the core design of the reactor. FLiNaK is used as the secondary coolant for the calculations. Both forced circulation and natural circulation options are evaluated. (author)

  13. Conceptual design of loop-in-tank type Indian molten salt breeder reactor concept

    International Nuclear Information System (INIS)

    The third stage of Indian nuclear power programme envisages use of thorium as fertile material with 233U, which is proposed to be obtained from reprocessing of spent fuel of Pu/Th based fast reactors in the later part of the second stage of the programme. In India, thorium based reactors have been designed in many configurations, from light water cooled designs to high temperature liquid metal and molten salt cooled options. Another option, which holds promise, is the molten salt-fuelled reactor, which can be configured to give significant breeding ratios. A crucial part for achieving reasonable breeding in such reactors is the need to reprocess the salt continuously, either online or in batch mode. India has recently started carrying out fundamental studies so as to arrive at a conceptual design of Indian Molten Salt Breeder Reactor (IMSBR). (author)

  14. Status of fast breeder reactor development in India

    International Nuclear Information System (INIS)

    The energy scenario and economic conditions in India are presented. India needs considerable energy for its rapid industrialisation with the liberal economic policy. Nuclear energy with FBR is the only large scale energy resource other than coal, available in the country. The present economic constraints have delayed the construction of new NPPs. The performance of operating reactors has improved considerably during the year. Operating experience of FBTR has been detailed particularly the reactivity incident and its investigations. Updated design of 500 MWe PFBR is presented. Various R and D works in support of FBR in the engineering, metallurgy, chemistry, reprocessing, safety etc. are detailed. (author)

  15. Seismic analysis of liquid metal fast breeder reactors

    International Nuclear Information System (INIS)

    This report is a general survey of the recent methods to predict the seismic structural behaviour of LMFBRs. It shall put into evidence the impact of seismic analysis on the design of the different structures of the reactor. This report is addressed to specialists and institutions of governmental organizations in industrialized and developing countries responsible for the design and operation of LMFBRs. The information presented should enable specialists in the R and D institutions and industries likely to be involved, to establish the correct course of the design and operation of LMFBRs. Also, the safety aspect of seismic risk are emphasized in the report. Refs and figs

  16. Studies of the restructuring of fast breeder test reactor fuel by out-of-pile simulation

    International Nuclear Information System (INIS)

    The fast breeder test reactor (FBTR) at Kalpakkam, India, currently employs a mixed carbide of uranium and plutonium with a Pu/(Pu + U) ratio of 0.70 as fuel. The behavior of this fuel in a thermal gradient is investigated. An out-of-pile simulation facility is designed, set up, and commissioned. Experiments are conducted on FBTR fuel pellets to study the restructuring of the fuel at various levels of linear power and its cracking behavior in a thermal gradient. The results are discussed in terms of their significance for reactor operation

  17. Software development methodology for computer based I&C systems of prototype fast breeder reactor

    International Nuclear Information System (INIS)

    Highlights: • Software development methodology adopted for computer based I&C systems of PFBR is detailed. • Constraints imposed as part of software requirements and coding phase are elaborated. • Compliance to safety and security requirements are described. • Usage of CASE (Computer Aided Software Engineering) tools during software design, analysis and testing phase are explained. - Abstract: Prototype Fast Breeder Reactor (PFBR) is sodium cooled reactor which is in the advanced stage of construction in Kalpakkam, India. Versa Module Europa bus based Real Time Computer (RTC) systems are deployed for Instrumentation & Control of PFBR. RTC systems have to perform safety functions within the stipulated time which calls for highly dependable software. Hence, well defined software development methodology is adopted for RTC systems starting from the requirement capture phase till the final validation of the software product. V-model is used for software development. IEC 60880 standard and AERB SG D-25 guideline are followed at each phase of software development. Requirements documents and design documents are prepared as per IEEE standards. Defensive programming strategies are followed for software development using C language. Verification and validation (V&V) of documents and software are carried out at each phase by independent V&V committee. Computer aided software engineering tools are used for software modelling, checking for MISRA C compliance and to carry out static and dynamic analysis. Various software metrics such as cyclomatic complexity, nesting depth and comment to code are checked. Test cases are generated using equivalence class partitioning, boundary value analysis and cause and effect graphing techniques. System integration testing is carried out wherein functional and performance requirements of the system are monitored

  18. Final report for the Light Water Breeder Reactor proof-of-breeding analytical support project

    International Nuclear Information System (INIS)

    The technology of breeding 233U from 232Th in a light water reactor is being developed and evaluated by the Westinghouse Bettis Atomic Power Laboratory (BAPL) through operation and examination of the Shippingport Light Water Breeder Reactor (LWBR). Bettis is determining the end-of-life (EOL) inventory of fissile uranium in the LWBR core by nondestructive assay of a statistical sample comprising approximately 500 EOL fuel rods. This determination is being made with an irradiated-fuel assay gauge based on neutron interrogation and detection of delayed neutrons from each rod. The EOL fissile inventory will be compared with the beginning-of-life fissile loading of the LWBR to determine the extent of breeding. In support of the BAPL proof-of-breeding (POB) effort, Argonne National Laboratory (ANL) carried out destructive physical, chemical, and radiometric analyses on 17 EOL LWBR fuel rods that were previously assayed with the nondestructive gauge. The ANL work included measurements on the intact rods; shearing of the rods into pre-designated contiguous segments; separate dissolution of each of the more than 150 segments; and analysis of the dissolver solutions to determine each segment's uranium content, uranium isotopic composition, and loading of selected fission products. This report describes the facilities in which this work was carried out, details operations involved in processing each rod, and presents a comprehensive discussion of uncertainties associated with each result of the ANL measurements. Most operations were carried out remotely in shielded cells. Automated equipment and procedures, controlled by a computer system, provided error-free data acquisition and processing, as well as full replication of operations with each rod. Despite difficulties that arose during processing of a few rod segments, the ANL destructive-assay results satisfied the demanding needs of the parent LWBR-POB program

  19. Final report for the Light Water Breeder Reactor proof-of-breeding analytical support project

    Energy Technology Data Exchange (ETDEWEB)

    Graczyk, D.G.; Hoh, J.C.; Martino, F.J.; Nelson, R.E.; Osudar, J.; Levitz, N.M.

    1987-05-01

    The technology of breeding /sup 233/U from /sup 232/Th in a light water reactor is being developed and evaluated by the Westinghouse Bettis Atomic Power Laboratory (BAPL) through operation and examination of the Shippingport Light Water Breeder Reactor (LWBR). Bettis is determining the end-of-life (EOL) inventory of fissile uranium in the LWBR core by nondestructive assay of a statistical sample comprising approximately 500 EOL fuel rods. This determination is being made with an irradiated-fuel assay gauge based on neutron interrogation and detection of delayed neutrons from each rod. The EOL fissile inventory will be compared with the beginning-of-life fissile loading of the LWBR to determine the extent of breeding. In support of the BAPL proof-of-breeding (POB) effort, Argonne National Laboratory (ANL) carried out destructive physical, chemical, and radiometric analyses on 17 EOL LWBR fuel rods that were previously assayed with the nondestructive gauge. The ANL work included measurements on the intact rods; shearing of the rods into pre-designated contiguous segments; separate dissolution of each of the more than 150 segments; and analysis of the dissolver solutions to determine each segment's uranium content, uranium isotopic composition, and loading of selected fission products. This report describes the facilities in which this work was carried out, details operations involved in processing each rod, and presents a comprehensive discussion of uncertainties associated with each result of the ANL measurements. Most operations were carried out remotely in shielded cells. Automated equipment and procedures, controlled by a computer system, provided error-free data acquisition and processing, as well as full replication of operations with each rod. Despite difficulties that arose during processing of a few rod segments, the ANL destructive-assay results satisfied the demanding needs of the parent LWBR-POB program.

  20. Program of Experiments in the KNK II Breeder Power Plant

    International Nuclear Information System (INIS)

    The sodium cooled fast reactor KNK II in the Research Center of Karlsruhe with a thermal power of 58 MW and an electric power of 20 MW has the mission, like other experimental plants such as EBRII in the US, RAPSODIE in France or JOYO in Japan, to collect experience for the construction and the operation of prototype plants. For KNK II, this program comprised the following areas: irradiation experiments and the corresponding post-irradiation examination, fuel cycle, instrumentation and detection techniques, operation related experiments and reactor chemistry. These areas are described in this report, after an illustration of the properties of KNK II as an irradiation reactor

  1. Supplement to Final Environmental Statement related to construction and operation of Clinch River Breeder Reactor Plant, Docket No. 50-537

    International Nuclear Information System (INIS)

    In February 1977, the Office of Nuclear Reactor Regulation issued a Final Environmental Statement (FES) (NUREG-0139) related to the construction and operation of the proposed Clinch River Breeder Reactor Plant (CRBRP). Since the FES was issued, additional data relative to the site and its environs have been collected, several modifications have been made to the CRBRP design, and its fuel cycle, and the timing of the plant construction and operation has been affected in accordance with deferments under the DOE Liquid Metal Fast Breeder Reactor (LMFBR) program. These changes are summarized and their environmental significance is assessed in this document. The reader should note that this document generally does not repeat the substantial amount of information in the FES which is still current; hence, the FES should be consulted for a comprehensive understanding of the staff's environmental review of the CRBRP project

  2. Development of variable-width ribbon heating elements for liquid-metal and gas-cooled fast breeder reactor fuel-pin simulators

    International Nuclear Information System (INIS)

    Variable-width ribbon heating elements that provide a chopped-cosine variable heat flux profile have been fabricated for fuel pin simulators used in test loops by the Breeder Reactor Program Thermal-Hydraulic Out-of-Reactor Safety test facility and the Gas-Cooled Fast Breeder Reactor-Core Flow Test Loop. Thermal, mechanical, and electrical design considerations are used to derive an analytical expression that precisely describes ribbon contour in terms of the major fabrication parameters. These parameters are used to generate numerical control tapes that control ribbon cutting and winding machines. Infrared scanning techniques are developed to determine the optimum transient thermal profile of the coils and relate this profile to that generated by the coils in completed fuel pin simulators

  3. Lessons learned from the licensing process for the Clinch River Breeder Reactor Plant

    International Nuclear Information System (INIS)

    This paper presents the experience of licensing a specific liquid-metal fast breeder reactor (LMFBR), the Clinch River Breader Reactor Plant (CRBRP). It was a success story in that the licensing process was accomplished in a very short time span. The actions of the applicant and the actions of the US Nuclear Regulatory Commission (NRC) in response are presented and discussed to provide guidance to future efforts to license unconventional reactors. The history is told from the perspective of the authors. As such, some of the reasons given for success or lack of success are subjective interpretations. Nevertheless, the authors' positions provided them an excellent viewpoint to make these judgements. During the second phase of the licensing process, they were the CRBRP Technical Director and the Licensing Manager, respectively, for the Westinghouse Electric Corporation, the prime contractor for the reactor plant

  4. Development of metallic fuels for Indian Fast Breeder Reactors

    International Nuclear Information System (INIS)

    The neutronic performance of metal fuel based on binary U-Pu alloy or ternary U-Pu-Zr alloys are better than conventional uranium plutonium mixed oxide or high density carbide ceramic fuel. The growing energy demand in India needs faster growth of nuclear power and warrants introduction of fast reactors based on metallic fuels in future. Physics calculation showed that fast reactor based on metallic fuels results in higher breeding ratio and lower doubling time compare to mixed oxide or carbide fuels. Moreover inclusion of pyro-processing of the fuel in the fuel cycle is expected to make metal fuel option more economical. As part of metal fuel development programme for future FBR's in India, capsule irradiation of metal fuel based on sodium bonded U-Pu-Zr alloy and metal (Zircaloy) bonded binary U-Pu (Pu ∼ 15 %) alloy are being actively pursued. For this purpose two design concepts have been proposed : one based on sodium bonded ternary alloy fuel of U-Pu-Zr (2-10 wt%) in modified T91 cladding material and the other is U-Pu binary alloy mechanically bonded to modified T91 cladding material with 'Zircaloy' as a liner between the fuel alloy and the clad. The Zircaloy liner act as a barrier in reducing the fuel clad chemical interaction. It also helps in transfer of heat from the fuel to the clad. The smear density of metal bonded pin will be between 70% - 85% and that for sodium bonded pin will be ∼ 70%. In metal bonded fuel pin design two/four semi-circular grooves of diameter ∼1.0 mm, will be provided in diametrically opposite directions in the fuel cross section to accommodate fuel swelling. A comparison has been made on the relative merits and demerits of these two fuel pin designs. The material for the axial blanket will be 'U' or U-Zr (Zr upto 10wt %) alloy based on the results of the out-of-pile thermal cycling behavior and irradiation performance. In the present investigation out-of-pile experiments have been carried out to address some of the issues of

  5. Status of fast breeder reactor development in the Federal Republic of Germany, Belgium and the Netherlands - February 1985

    International Nuclear Information System (INIS)

    In 1967 and 1968, the Federal Republic of Germany, the Kingdom of Belgium and the Kingdom of the Netherlands (''DeBeNe'') agreed to develop breeder reactors in a joint program. The following research organizations have taken part in this effort: Kernforschungszentrum Karlsruhe (KfK); INTERATOM, Bergisch Gladbach; ALKEM, Wolfgang near Hanau; SCK/CEN, Mol; Belgonucleaire, Brussels; ECN, Petten; TNO, Apeldoorn; NERATOOM, The Hague. The three Germany institutions mentioned above have been associated since 1977 in the Entwicklungsgemeinschaft (EG) Schneller Brueter. KfK, INTERATOM, and the French Commissariat a l'Energie Atomique entered into contracts in 1977 about close cooperation in the fast breeder field, to which the Belgian and Dutch partners acceded. The results of activities carried out by the DeBeNe partners in 1984 have been compiled in this report. The report begins with a survey of the fast reactor plants followed by a R and D summary. In an additional chapter, a survey is given of international cooperation in 1984

  6. Status of fast breeder reactor development in the Federal Republic of Germany, Belgium and The Netherlands - February 1984

    International Nuclear Information System (INIS)

    In 1967 and 1968 the Federal Republic of Germany, the Kingdom of Belgium and the Kingdom of the Netherlands (''DeBeNe'') agreed to develop breeder reactors in a joint program. The following research organizations have taken part in this effort: Kernforschungszentrum Karlsruhe (KfK); INTERATOM, Bergisch Gladbach; ALKEM, Wolgang near Hanau; SCK/CEN, Mol; Belgonucleaire, Brussels; ECN, Petten; TNO, Apeldoorn; NERATOOM, The Hague. The three German institutions mentioned above have been connected since 1977 in the Entwicklungsgemeinschaft (EG) Schneller Brueter. KfK, INTERATOM, and the French Commissariat a l'Energie Atomique entered into contracts in 1977 about close cooperation in the fast breeder field, to which the Belgian and Dutch partners acceded. The results of activities carried out by the DeBeBe partners in 1983 have been compiled in this report. The report begins with a survey of the fast reactor plants followed by an R and D summary. In an additional chapter, a survey is given of international cooperation in 1983

  7. Light water reactor program

    Energy Technology Data Exchange (ETDEWEB)

    Franks, S.M.

    1994-12-31

    The US Department of Energy`s Light Water Reactor Program is outlined. The scope of the program consists of: design certification of evolutionary plants; design, development, and design certification of simplified passive plants; first-of-a-kind engineering to achieve commercial standardization; plant lifetime improvement; and advanced reactor severe accident program. These program activities of the Office of Nuclear Energy are discussed.

  8. Can the breeder go commercial

    International Nuclear Information System (INIS)

    Contrary to some beliefs in the electric utility industry that ERDA is committed to developing a commercial breeder economy, it is pointed out that ERDA isn't even willing to pay the total cost of the R and D program--and unless there is a major commitment from the private sector (the electric utility industry, in particular) the breeder program will die. The schedule as of Fall 1976 called for: (1) Fast Flux Test Facility (scheduled to go critical in 1979, operate in 1980); (2) Clinch River Breeder Reactor Project (CRBRP) (1/3 commercial size plant hopefully operating by 1983); (3) Prototype Large Breeder Reactor (planned construction starting in 1981, operating in 1988); and (4) Commercial Breeder Reactor (CBR-1 design work to start in 1983, construction in 1986, and operation in 1993). The $257 million the utility industry has pledged to the CRBRP was just for openers. The $2 billion follow-on breeder project being designed calls for massive capital input from a utility (or utility consortium)--and if that is not forthcoming, then in the words of an ERDA official, ''we'll have to reassess the whole breeder program.''

  9. Analysis for mechanical consequences of a core disruptive accident in Prototype Fast Breeder Reactor

    International Nuclear Information System (INIS)

    The mechanical consequences of a core disruptive accident (CDA) in a fast breeder reactor are described. The consequences are development of deformations and strains in the vessels, intermediate heat exchangers (IHX) and decay heat exchangers (DHX), impact of sodium slug on the bottom surface of the top shield, sodium release to reactor containment building through top shield penetrations, sodium fire and consequent temperature and pressure rise in reactor containment building (RCB). These are quantified for 500 MWe Prototype Fast Breeder Reactor (PFBR) for a CDA with 100 MJ work potential. The results are validated by conducting a series of experiments on 1/30 and 1/13 scaled down models with increasing complexities. Mechanical energy release due to nuclear excursion is simulated by chemical explosion of specially developed low density explosive charge. Based on these studies, structural integrity of primary containment, IHX and DHX is demonstrated. The sodium release to RCB is 350 kg which causes pressure rise of 12 kPa in RCB. (author)

  10. Sodium and steam generator leak detection for prototype fast breeder reactor (PFBR)

    International Nuclear Information System (INIS)

    The construction of the Prototype Fast Breeder Reactor (PFBR) a 500 MWe pool type sodium cooled breeder reactor with MOX fuel has started at Kalpakkam. The Instrumentation and Control of PFBR is designed for safe, reliable and economic operation of the plant. Special feature of breeder reactors is sodium instrumentation. Leaks in sodium systems have the possibility of being exceptionally hazardous due to the reaction of liquid sodium with oxygen and water vapour in the air. In addition, leakage from primary systems can cause radioactive contamination. Potential regions of leakage are near welds and high stress areas. Sodium also reacts with concrete releasing hydrogen and leading to damage and loss of strength of concrete structures. Leaking sodium catches fire depending on its temperature. Sodium temperature in the plant ranges from 423 K at filling condition to 820 K at reactor nominal power operating condition. Leak detectors are provided on pipelines, tanks and other capacities. Sodium leak detection systems are designed to meet requirements of ASME section XI- division 3 which specifies that sodium leak at the rate of 100 g/h are to be detected in 20 h for air filled vaults and 250 h for inert vaults. Diverse leak detection methods are employed for active and non-active sodium equipment and pipes. For detection of water leaks into Sodium in steam generators, Hydrogen in Sodium Detectors (HSD) are used. Hydrogen in Argon Detectors (HAD) are used for sodium temperatures below 623 K as HSD is not effective below this temperature due to non-dissolution of hydrogen formed. Choice and challenges posed in implementation of above leak detection requirements are discussed in this paper. (authors)

  11. Review of the SIMMER-II analyses of liquid-metal-cooled fast breeder reactor core-disruptive accident fuel escape

    International Nuclear Information System (INIS)

    Early fuel removal from the active core of a liquid-metal-cooled fast breeder reactor undergoing a core-disruptive accident may reduce the potential for large energetics resulting from recriticalities. This paper presents a review of analyses with the SIMMER-II computer program of the effectiveness of possible fuel escape paths. Where possible, how SIMMER-II compares with or is validated against experiments that simulated the escape paths also is discussed

  12. The fusion breeder

    International Nuclear Information System (INIS)

    The fusion breeder is a fusion reactor designed with special blankets to maximize the transmutation by 14 MeV neutrons of uranium-238 to plutonium or thorium to uranium-233 for use as a fuel for fission reactors. Breeding fissile fuels has not been a goal of the U.S. fusion energy program. This paper suggests it is time for a policy change to make the fusion breeder a goal of the U.S. fusion program and the U.S. nuclear energy program. There is wide agreement that many approaches will work and will produce fuel for five equal-sized LWRs, and some approach as many as 20 LWRs at electricity costs within 20% of those at today's price of uranium ($30/lb of U3O8). The blankets designed to suppress fissioning, called symbiotes, fusion fuel factories, or just fusion breeders, will have safety characteristics more like pure fusion reactors and will support as many as 15 equal power LWRs. The blankets designed to maximize fast fission of fertile material will have safety characteristics more like fission reactors and will support 5 LWRs. This author strongly recommends development of the fission suppressed blanket type, a point of view not agreed upon by everyone. There is, however, wide agreement that, to meet the market price for uranium which would result in LWR electricity within 20% of today's cost with either blanket type, fusion components can cost severalfold more than would be allowed for pure fusion to meet the goal of making electricity alone at 20% over today's fission costs. Also widely agreed is that the critical-pathitem for the fusion breeder is fusion development itself; however, development of fusion breeder specific items (blankets, fuel cycle) should be started now in order to have the fusion breeder by the time the rise in uranium prices forces other more costly choices

  13. Conjugate heat transfer analysis of multiple enclosures in prototype fast breeder reactor

    Energy Technology Data Exchange (ETDEWEB)

    Velusamy, K.; Balaubramanian, V.; Vaidyanathan, G.; Chetal, S.C. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

    1995-09-01

    Prototype Fast Breeder Reactor (PFBR) is a 500 MWe sodium cooled reactor under design. The main vessel of the reactor serves as the primary boundary. It is surrounded by a safety vessel which in turn is surrounded by biological shield. The gaps between them are filled with nitrogen. Knowledge of temperature distribution prevailing under various operating conditions is essential for the assessment of structural integrity. Due to the presence of cover gas over sodium free level within the main vessel, there are sharp gradients in temperatures. Also cover gas height reduces during station blackout conditions due to sodium level rise in main vessel caused by temperature rise. This paper describes the model used to analyse the natural convection in nitrogen, conduction in structures and radiation interaction among them. Results obtained from parametric studies for PFBR are also presented.

  14. Implementation of multivariable control techniques with application to Experimental Breeder Reactor II

    International Nuclear Information System (INIS)

    After several successful applications to aerospace industry, the modern control theory methods have recently attracted many control engineers from other engineering disciplines. For advanced nuclear reactors, the modern control theory may provide major advantages in safety, availability, and economic aspects. This report is intended to illustrate the feasibility of applying the linear quadratic Gaussian (LQG) compensator in nuclear reactor applications. The LQG design is compared with the existing classical control schemes. Both approaches are tested using the Experimental Breeder Reactor 2 (EBR-2) as the system. The experiments are performed using a mathematical model of the EBR-2 plant. Despite the fact that the controller and plant models do not include all known physical constraints, the results are encouraging. This preliminary study provides an informative, introductory picture for future considerations of using modern control theory methods in nuclear industry. 10 refs., 25 figs

  15. The fast breeder reactor Rapsodie (1962); Le reacteur rapide surregenerateur rapsodie (1962)

    Energy Technology Data Exchange (ETDEWEB)

    Vautrey, L.; Zaleski, C.P. [Commissariat a l' Energie Atomique, Cadarache (France). Centre d' Etudes Nucleaires

    1962-07-01

    In this report, the authors describe the Rapsodie project, the French fast breeder reactor, as it stands at construction actual start-up. The paper provides informations about: the principal neutronic and thermal characteristics, the reactor and its cooling circuits, the main handling devices of radioactive or contaminated assemblies, the principles and means governing reactor operation, the purposes and locations of miscellaneous buildings. Rapsodie is expected to be critical by 1964. (authors) [French] Dans ce rapport, les auteurs font le point du projet RAPSODIE (reacteur francais surregenerateur a neutrons rapides), au moment du debut effectif de sa construction. On y trouvera decrits: les principales caracteristiques neutroniques et thermiques, le bloc pile et les circuits de refroidissement, les principaux moyens de manutention des ensembles actifs ou contamines, les principes et les moyens qui regissent la conduite du reacteur, les fonctions et l'implantation des divers batiments. La divergence de RAPSODIE est prevue pour 1964. (auteurs)

  16. Large scale breeder reactor plant prototype mechanical pump conceptual design study

    Energy Technology Data Exchange (ETDEWEB)

    1976-07-01

    This final report is a complete conceptual design study of a mechanical pump for a large scale breeder reactor plant. The pumps are located in the cold leg side of the loops. This makes the net positive suction head available - NPSHA - low, and is, in fact, a major influencing factor in the design. Where possible, experience gained from the Clinch River Project and the FFTF is used in this study. Experience gained in the design, manufacturer, and testing of pumps in general and sodium pumps in particular is reflected in this report. The report includes estimated cost and time schedule for design, manufacture, and testing. It also includes a recommendation for development needs.

  17. It is now time to proceed with a gas-cooled breeder reactor (GBR) demonstration plant

    International Nuclear Information System (INIS)

    Since 1969, the GBRA has been making studies to provide evidence on questions which were not clear regarding the Gas-cooled Breeder Reactor: design feasibility and performance, safety, strategy and economics, and R and D necessary for a demonstration plant. Studies were carried out on a 1200-MW(e) commercial reference design with pin fuel, which was also used as a basis for a definition of the GBR demonstration plant. During the six years, a great deal of information has been generated at GBRA and it confirms the forecasts of the promoters of the Gas-cooled Breeder Reactor that the GBR is an excellent reactor from all points of view: design - the reactor can be engineered without major difficulty, using present techniques. As far as fuel is concerned, LMFBR fuel technology is applicable plus limited specific development effort. Performance - the GBR is the best breeder with oxide fuel and using conventional techniques. The strategy studies carried out at GBRA have clearly shown that a high performance breeder such as the GBR is absolutely required in large quantities by the turn of the century in order to avoid dependence on natural uranium resources. Regarding safety, a major step forward has been made when an ad hoc group on GBR safety, sponsored by the EEC, concluded that no major difficulties were anticipated which would prevent the GBR reaching adequate safety standards. Detailed economic assessments performed on an item-to-item basis have shown that the cost of a GBR with its high safety standard is about the same as that of an HTR. One can therefore conclude that, with the present cost of natural uranium, the GBR is competitive with the LWRs. Owing to the very limited R and D effort necessary and the obvious safety, economic and strategic advantages of the concept, it is concluded that the development and construction of a GBR demonstration plant must be started now if one wants to secure an adequate energy supply past the turn of the century. (author)

  18. Compendium of computer codes for the safety analysis of fast breeder reactors

    International Nuclear Information System (INIS)

    The objective of the compendium is to provide the reader with a guide which briefly describes many of the computer codes used for liquid metal fast breeder reactor safety analyses, since it is for this system that most of the codes have been developed. The compendium is designed to address the following frequently asked questions from individuals in licensing and research and development activities: (1) What does the code do. (2) To what safety problems has it been applied. (3) What are the code's limitations. (4) What is being done to remove these limitations. (5) How does the code compare with experimental observations and other code predictions. (6) What reference documents are available

  19. Preliminary design of a Binary Breeder Reactor; Diseno preliminar de un reactor esferico de quema/cria

    Energy Technology Data Exchange (ETDEWEB)

    Garcia C, E. Y.; Francois, J. L.; Lopez S, R. C., E-mail: eliasgarcerv@hotmail.com [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Paseo Cuauhnahuac No. 8532, 62550 Jiutepec, Morelos (Mexico)

    2014-10-15

    A binary breeder reactor (BBR) is a reactor that by means of the transmutation and fission process can operates through the depleted uranium burning with a small quantity of fissile material. The advantages of a BBR with relation to other nuclear reactor types are numerous, taking into account their capacity to operate for a long time without requiring fuel reload or re-arrangement. In this work four different simulations are shown carried out with the MCNPX code with libraries Jeff-3.1 to 1200 K. The objective of this study is to compare two different models of BBR: a spherical reactor and a cylindrical one, using two fuel cycles for each one of them (U-Pu and Th-U) and different reflectors for the two different geometries. For all the models a super-criticality state was obtained at least 10.9 years without carrying out some fuel re-arrangement or reload. The plutonium-239 production was achieved in the models where natural uranium was used in the breeding area, while the production of uranium-233 was observed in the cases where thorium was used in the fertile area. Finally, a behavior of stationary wave reactor was observed inside the models of spherical reactor when contemplating the power uniform increment in the breeding area, while inside the cylindrical models was observed the behavior of a traveling wave reactor when registering the displacement of the burnt wave along the cylindrical model. (Author)

  20. Review of uncertainty estimates associated with models for assessing the impact of breeder reactor radioactivity releases

    International Nuclear Information System (INIS)

    The purpose is to summarize estimates based on currently available data of the uncertainty associated with radiological assessment models. The models being examined herein are those recommended previously for use in breeder reactor assessments. Uncertainty estimates are presented for models of atmospheric and hydrologic transport, terrestrial and aquatic food-chain bioaccumulation, and internal and external dosimetry. Both long-term and short-term release conditions are discussed. The uncertainty estimates presented in this report indicate that, for many sites, generic models and representative parameter values may be used to calculate doses from annual average radionuclide releases when these calculated doses are on the order of one-tenth or less of a relevant dose limit. For short-term, accidental releases, especially those from breeder reactors located in sites dominated by complex terrain and/or coastal meteorology, the uncertainty in the dose calculations may be much larger than an order of magnitude. As a result, it may be necessary to incorporate site-specific information into the dose calculation under these circumstances to reduce this uncertainty. However, even using site-specific information, natural variability and the uncertainties in the dose conversion factor will likely result in an overall uncertainty of greater than an order of magnitude for predictions of dose or concentration in environmental media following shortterm releases

  1. Experience of secondary cooling system modification at prototype fast breeder reactor MONJU (Translated document)

    International Nuclear Information System (INIS)

    The prototype fast breeder reactor MONJU has been shut down since the secondary sodium leak accident that occurred in December 1995. After the accident, an investigation into the cause and a comprehensive safety review of the plant were conducted, and various countermeasures for sodium leak were examined. Modification work commenced in September 2005. Since sodium, a chemically active material, is used as coolant in MONJU, the modification work required work methods suitable for the handling of sodium. From this perspective, the use of a plastic bag when opening the sodium boundary, oxygen concentration control in a plastic bag, slightly-positive pressure control of cover gas in the systems, pressing and cutting with a roller cutter to prevent the incorporation of metal fillings, etc. were adopted, with careful consideration given to experience and findings from previous modification work at the experimental fast reactor JOYO and plants abroad. Owing to these work methods, the modification work proceeded close to schedule without incident. (author)

  2. Liquid metal seal (LMS) - challenges for fast breeder test reactor (FBTR)

    International Nuclear Information System (INIS)

    In Fast Breeder Test reactor (FBTR), Liquid Metal Seal (LMS) is being used to maintain leak tightness between reactor vessel and rotating plugs. It is a eutectic mixture of 42% tin and 58% bismuth. This paper describes measurements of melting point of LMS using Differential Scanning Calorimeter (DSC), Make: Setaram; Model- 131 evo. The instrument was calibrated using Indium as standard with different heating rates, 5 °C/min, 10 °C/min, 15°C/min and 20 °C/min. The observed value of melting point was found to be in agreement with the literature value. The melting point of as received and used LMS (LMSH8, LMSH10 and LMSH12) from three locations of FBTR were studied using DSC with different heating rates as above. The results are presented and it can be clearly seen that LMS has undergone some modifications during the continuous usage in FBTR

  3. Design optimization of backup seal for sodium cooled fast breeder reactor

    International Nuclear Information System (INIS)

    Highlights: ► Design arrived from fourteen geometric options by finite element analysis. ► Seal geometry, size, compression, contact pressure, stress and compression load optimized. ► Effects of reduced fluoroelastomer strength at 110 °C, strain rate and stress-softening incorporated. ► Ageing, friction, tolerances, batch-to-batch/production variations in fluoroelastomer considered. ► Procedure applicable to other elastomeric seals of Fast Breeder Reactors. -- Abstract: Design optimization of static, fluoroelastomer backup seals for the 500 MWe, Prototype Fast Breeder Reactor (PFBR) is depicted. 14 geometric variations of a solid trapezoidal cross-section were studied by finite element analysis (FEA) to arrive at a design with hollowness and double o-ring contours on the sealing face. The seal design with squeeze of 5 mm assures failsafe operation for at least 10 years under a differential pressure of 25 kPa and ageing influences of fluid (air), temperature (110 °C) and γ radiation (23 mGy/h) in reactor. Hybrid elements of 1 mm length, regular integration, Mooney–Rivlin material model and Poisson’s ratio of 0.493 were used in axisymmetric analysis scheme. Possible effects of reduced fluoroelastomer strength at 110 °C, ageing, friction, tolerances in reactor scale, testing conditions during FEA data generation and batch-to-batch/production variations in seal material were considered to ensure adequate safety margin at the end of design life. The safety margin and numerical prediction accuracy could be improved further by using properties of specimens extracted from seal. The approach is applicable to other low pressure, moderate temperature elastomeric sealing applications of PFBR, mostly operating under maximum strain of 50%.

  4. Design of fuel fabrication plant of Fast Reactor Fuel Cycle Facility for reload requirement of Prototype Fast Breeder Reactor

    International Nuclear Information System (INIS)

    India's economic growth is on a fast growth track. The energy demand is expected to grow rapidly in the coming decades. The growth in population and economy is creating huge demand for energy which has to be met with environmentally benign technologies. Nuclear energy is best suited to meet this demand in a sustainable manner without causing undue environmental impact. Fast reactors are expected to be major contributors in sufficing this demand to a great extent. As an effort to achieve the objective, a Prototype Fast Breeder Reactor is being constructed at Kalpakkam. This paper also highlights the design features of FFP, unit operations, scheme of automation, branched layout of glove box train, shielding arrangement on glove boxes, accident consequence analysis etc.

  5. C-scope under-sodium viewer for sodium-cooled fast breeder reactor

    International Nuclear Information System (INIS)

    A C-scope under-sodium viewer has been developed for monitoring the interior of sodium-cooled fast breeder reactors. Consisting of a transducer that emits and receives ultrasonic waves under liquid sodium, a mechanism that drives the transducer under liquid sodium and an image displaying section, it inspects the fuel assembly through its image in optically opaque high-temperature (3000C) liquid sodium. The results of its evaluation test are: (1) The transducer could continue satisfactory operation under 3500C (at the highest) sodium for more than a month. (2) The driving mechanism, though it was the first of the kind appearing in Japan, has been proved that it could continue operation for a week under 3000C sodium. (3) The image displaying section, in spite of the low speed of the transducer (below 20 rpm), could display stable and clear images. (4) The image in 3000C was as clear as that in room-temperature water. (auth.)

  6. Development of an ISI Robot for the Fast Breeder Reactor MONJU Primary Heat Transfer System Piping

    International Nuclear Information System (INIS)

    This paper describes the development of a new inspection robot for the In-Service Inspection of the heat transfer system of the Fast Breeder Reactor MONJU. The inspection was carried out using a tire type ultrasonic sensor for volumetric tests at high temperature (atmosphere 55 degree C, Piping Surface 80 degree C) and radiation exposure condition (dose rate 10 mGy/h, piping surface dose rate 15 mGy/h). It was developed an inspection robot using a new tire type for the ultrasonic testing sensor and a new control method. A signal to noise ratio S/N over 2 was obtained during the functional test for a calibration defect with depth 50%t (from the tube wall thickness). (author)

  7. Ultrasonic inspection of liquid-metal fast breeder reactor steam generator duplex tubing

    International Nuclear Information System (INIS)

    Two ultrasonic inspections of the Experimental Breeder Reactor II steam generator duplex tubing have been completed. Inspections performed on one evaporator in 1976 provided baseline data, and a subsequent inspection in 1978 revealed no change in tube condition. With the completion of the 1978 inspection, all available tubes in one evaporator have been inspected. The steam generator contains duplex tubes fabricated from 2 1/4 Cr-1 Mo ferritic steel. Access to the bore (water) side of the tubes was gained through the steam outlet piping. The inspection included a complete volumertic (100% of the tube material) examination, measurement of wall thickness, and evaluation of the condition of the braze bonding the two walls of the tube together. The test equipment was routinely calibrated against a standard containing artificial flaws. Artificial flaws as small as 1.6 mm long x 0.25 mm deep were readily detected

  8. Global depletion analysis of Korean helium cooled solid breeder TBM model for demo fusion reactor

    International Nuclear Information System (INIS)

    The Korean HCSB (helium cooled solid breeder) TBM (test blanket module) is proposed with its specific compositions of lithium ceramic, beryllium and graphite in pebble form. In the Korean HCSB TBM, the amount of beryllium is reduced and the reduction is replaced by graphite for a neutron reflector, while tritium breeding ratio (TBR) remains almost unchanged with relatively low Li6 enrichment of ∼40%. However, the previous Korean HCSB was designed based on the LOCAL assumption, in which the surroundings are assumed by the reflective boundary condition. In this research, we establish a simple GLOBAL neutronics model based on demo fusion reactor and perform neutronics analyses including depletion (transmutation) calculation during 100 EFPDs (effective full power days) using the modified MONTEBURNS code.

  9. Clinch River Breeder Reactor: an assessment of need for power and regulatory issues

    Energy Technology Data Exchange (ETDEWEB)

    Hamblin, D M; Tepel, R C; Bjornstad, D J; Hill, L J; Cantor, R A; Carroll, P J; Cohn, S M; Hadder, G R; Holcomb, B D; Johnson, K E

    1983-09-01

    The purpose of this report is to present the results of a research effort designed to assist the US Department of Energy in: (1) reviewing the need for power from the Clinch River Breeder Reactor (CRBR) in the Southeastern Electric Reliability Council (SERC) region, not including Florida, and (2) isolating specific regulatory and institutional issues and physical transmission capacities that may constrain the market for CRBR power. A review of existing electric power wheeling arrangements in the Southeast and specific federal and state regulatory obstacles that may affect power sales from the CRBR was undertaken. This review was a contributing factor to a decision to target the service territory to SERC-less Florida.

  10. Compendium of computer codes for the safety analysis of fast breeder reactors

    Energy Technology Data Exchange (ETDEWEB)

    1977-10-01

    The objective of the compendium is to provide the reader with a guide which briefly describes many of the computer codes used for liquid metal fast breeder reactor safety analyses, since it is for this system that most of the codes have been developed. The compendium is designed to address the following frequently asked questions from individuals in licensing and research and development activities: (1) What does the code do. (2) To what safety problems has it been applied. (3) What are the code's limitations. (4) What is being done to remove these limitations. (5) How does the code compare with experimental observations and other code predictions. (6) What reference documents are available.

  11. Determination and correlation of mass transfer coefficients in a stirred cell. [Molten Salt Breeder Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Herranz, J.; Bloxom, S.R.; Keeler, J.B.; Roth, S.R.

    1975-12-17

    In the proposed Molten Salt Breeder Reactor flowsheet, a fraction of the rare earth fission products is removed from the fuel salt in mass transfer cells. To obtain design parameters for this extraction, the effect of cell size, blade diameter, phase volume, and agitation rate on the mass transfer for a high density ratio system (mercury/water) in nondispersing square cross section contactors was determined. Aqueous side mass transfer coefficients were measured by polarography over a wide range of operating conditions. Correlations for the experimental mass transfer coefficients as functions of the operating parameters are presented. Several techniques for measuring mercury-side mass transfer coefficients were evaluated and a new one is recommended. (auth)

  12. Economic performance of liquid-metal fast breeder reactor and gas-cooled fast reactor radial blankets

    International Nuclear Information System (INIS)

    The economic performance of the radial blanket of a liquid-metal fast breeder reactor (LMFBR) and a gas-cooled fast reactor (GCFR) has been studied based on the calculation of the net financial gain as well as the value of the levelized fuel cost. The necessary reactor physics calculations have been performed using the code CITATION, and the economic analysis has been carried out with the code ECOBLAN, which has been written for that purpose. The residence time of fuel in the blanket is the main variable of the economic analysis. Other parameters that affect the results and that have been considered are the value of plutonium, the price of heat, the effective cost of money, and the holdup time of the spent fuel before reprocessing. The results show that the radial blanket of both reactors is a producer of net positive income for a broad range of values of the parameters mentioned above. The position of the fuel in the blanket and the fuel management scheme applied affect the monetary gain. There is no significant difference between the economic performance of the blanket of an LMFBR and a GCFR

  13. Acoustic monitoring of sodium boiling in a liquid metal fast breeder reactor from autoregressive models

    Energy Technology Data Exchange (ETDEWEB)

    Geraldo, Issa Cherif [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Bose, Tanmoy [Indian Institute of Technology Kharagpur, Kharagpur 721302, West Bengal (India); Pekpe, Komi Midzodzi, E-mail: midzodzi.pekpe@univ-lille1.fr [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Cassar, Jean-Philippe [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Mohanty, A.R. [Indian Institute of Technology Kharagpur, Kharagpur 721302, West Bengal (India); Paumel, Kévin [CEA, DEN, Nuclear Technology Department, F-13108 Saint-Paul-lez-Durance (France)

    2014-10-15

    Highlights: • The work deals with sodium boiling detection in a liquid metal fast breeder reactor. • The authors choose to use acoustic data instead of thermal data. • The method is designed to not to be disturbed by the environment noises. • A real time boiling detection methods are proposed in the paper. - Abstract: This paper deals with acoustic monitoring of sodium boiling in a liquid metal fast breeder reactor (LMFBR) based on auto regressive (AR) models which have low computational complexities. Some authors have used AR models for sodium boiling or sodium–water reaction detection. These works are based on the characterization of the difference between fault free condition and current functioning of the system. However, even in absence of faults, it is possible to observe a change in the AR models due to the change of operating mode of the LMFBR. This sets up the delicate problem of how to distinguish a change in operating mode in absence of faults and a change due to presence of faults. In this paper we propose a new approach for boiling detection based on the estimation of AR models on sliding windows. Afterwards, classification of the models into boiling or non-boiling models is made by comparing their coefficients by two statistical methods, multiple linear regression (LR) and support vectors machines (SVM). The proposed approach takes into account operating mode information in order to avoid false alarms. Experimental data include non-boiling background noise data collected from Phenix power plant (France) and provided by the CEA (Commissariat à l’Energie Atomique et aux énergies alternatives, France) and boiling condition data generated in laboratory. High boiling detection rates as well as low false alarms rates obtained on these experimental data show that the proposed method is efficient for boiling detection. Most importantly, it shows that the boiling phenomenon introduces a disturbance into the AR models that can be clearly detected.

  14. Acoustic monitoring of sodium boiling in a liquid metal fast breeder reactor from autoregressive models

    International Nuclear Information System (INIS)

    Highlights: • The work deals with sodium boiling detection in a liquid metal fast breeder reactor. • The authors choose to use acoustic data instead of thermal data. • The method is designed to not to be disturbed by the environment noises. • A real time boiling detection methods are proposed in the paper. - Abstract: This paper deals with acoustic monitoring of sodium boiling in a liquid metal fast breeder reactor (LMFBR) based on auto regressive (AR) models which have low computational complexities. Some authors have used AR models for sodium boiling or sodium–water reaction detection. These works are based on the characterization of the difference between fault free condition and current functioning of the system. However, even in absence of faults, it is possible to observe a change in the AR models due to the change of operating mode of the LMFBR. This sets up the delicate problem of how to distinguish a change in operating mode in absence of faults and a change due to presence of faults. In this paper we propose a new approach for boiling detection based on the estimation of AR models on sliding windows. Afterwards, classification of the models into boiling or non-boiling models is made by comparing their coefficients by two statistical methods, multiple linear regression (LR) and support vectors machines (SVM). The proposed approach takes into account operating mode information in order to avoid false alarms. Experimental data include non-boiling background noise data collected from Phenix power plant (France) and provided by the CEA (Commissariat à l’Energie Atomique et aux énergies alternatives, France) and boiling condition data generated in laboratory. High boiling detection rates as well as low false alarms rates obtained on these experimental data show that the proposed method is efficient for boiling detection. Most importantly, it shows that the boiling phenomenon introduces a disturbance into the AR models that can be clearly detected

  15. Design and fabrication of steam generators (superheaters) for the prototype fast breeder reactor 'MONJU'

    International Nuclear Information System (INIS)

    In liquid metal-cooled fast breeder reactors, steam generators are one of the important equipments, and emphasis has been placed on their development in various countries in the world. Also in Japan, centering around the Power Reactor and Nuclear Fuel Development Corp., the research and development in the wide range from the fundamentals on heat transfer and flow, materials and strength for steam generators to the manufacture, operation and various tests of large mock-ups including a 50 MW steam generator have been carried out. Further, as for the manufacture and inspection, the improvement of the method of welding tubes and tube plates, the adoption of a fine focus X-ray inspection apparatus and others were carried out. Moreover, as the maintenance technique, the ultrasonic flaw detection probes for the heating tubes were developed. The steam generators (superheaters) for the FBR 'Monju' power station are the heat exchangers of helical coil tube-shell type using SUS 321 steel as the heating tube material. Based on the results of these research and development, the design and manufacture of these superheaters and their installation in the reactor auxiliary building of the FBR 'Monju' power station were completed. The outline of the design, the research and development and the manufacture of the steam generators (superheaters) are reported. (K.I.)

  16. Fabrication and quality control of MOX fuel for Prototype Fast Breeder Reactor (PFBR)

    International Nuclear Information System (INIS)

    Full text: Uranium-Plutonium mixed oxide (MOX) fuel for both thermal and fast reactors have been fabricated by Advanced Fuel Fabrication Facility (AFFF), Bhabha Atomic Research Centre, Tarapur, India. MOX fuel bundles fabricated by AFFF have been loaded in Boiling Water Reactors (BWRs) and Pressurised Heavy Water Reactors (PHWRs) and have been discharged after successful irradiation. An experimental fuel subassembly containing 37 MOX pins is being irradiated in Fast Breeder Test Reactor (FBTR) at Kalpakkam near Chennai and has seen a burn up of more than 80000 MWD/T. MOX fuel pins containing 44% Pu02 have been recently loaded as a part of the hybrid core of FBTR. AFFF has now taken up the manufacture of MOX fuel pins for the Prototype Fast Breeder Reactor (BHAVINI) coming up at Kalpakkam. The core consists of 181 sub assemblies containing 217 MOX fuel pins each. It is required to fabricate nearly 40,000 MOX fuel pins (3 meter long) for the first core. The Prototype Fast Breeder Reactor is designed with two different fissile enrichment zones to be loaded with MOX subassemblies with a nominal composition of 21% and 28% of PuO2. The fuel pellets of required composition are made using conventional powder metallurgy processes. The pellets are annular with an inner hole of 1.8mm diameter and outside diameter of 5.5mm. AFFF has developed the technology of making annular MOX fuel pellets for PFBR and optimized conditions of fabrication. Multistation rotary presses have been used for compaction of the pellets. The fuel pin consists of a MOX stack of 1000mm and axial blanket of deeply depleted uranium dioxide of length 300mm on either side. New techniques have been used at different stages of fabrication of the fuel pins namely pelletisation, welding and wire wrapping. Studies have been made to use laser welding technique for welding of endplugs. Automation has been introduced in a number of process steps in the fabrication line. A detailed quality control plan is prepared

  17. Fabrication and quality control of MOX fuel for Prototype Fast Breeder Reactor (PFBR)

    International Nuclear Information System (INIS)

    Uranium-Plutonium mixed oxide (MOX) fuel for both thermal and fast reactors have been fabricated by Advanced Fuel Fabrication Facility (AFFF), Bhabha Atomic Research Centre, Tarapur, India. MOX fuel bundles fabricated by AFFF have been loaded in Boiling Water Reactors (BWRs) and Pressurised Heavy Water Reactors (PHWRs) and have been discharged after successful irradiation. An experimental fuel subassemby containing 37 MOX pins is being irradiated in Fast Breeder Test Reactor (FBTR) at Kalpakkam near Chennai and has seen a burn up of more than 92000 MWd/t. MOX fuel pins containing 44% PuO2 have been recently loaded as a part of the hybrid core of FBTR. AFFF has now taken up the manufacture of MOX fuel pins for the Prototype Fast Breeder Reactor (PFBR) coming up at Kalpakkam . The core consists of 181 sub assemblies containing 217 MOX fuel pins each. Prototype Fast Breeder Reactor is designed with two different fissile enrichment zones to be loaded with MOX subassemblies with a nominal composition of 21% and 28% of PuO2.The fuel pellets of required composition are made using conventional powder metallurgy processes. The pellets are annular with an inner hole of 1.8 mm diameter and outside diameter of 5.5 mm. AFFF has developed the technology of making annular MOX fuel pellets for PFBR and optimized conditions of fabrication. Multistaion rotary presses have been used for compaction of the pellets. The fuel pin consists of a MOX stack of 1000 mm and axial blanket of deeply depleted uranium dioxide of length 300 mm on either side. New techniques have been used at different stages of fabrication of the fuel pins namely pelletisation, welding and wire wrapping. Studies have been made to use laser welding technique for welding of endplugs. Automation has been introduced in a number of process steps in the fabrication line. A detailed quality control plan is prepared based on the specifications and advanced process and quality control procedures have been incorporated to

  18. Development of fluorocarbon rubber for backup seals of sodium cooled fast breeder reactor

    International Nuclear Information System (INIS)

    Highlights: → Negligible chemical degradation of seal compound during ageing (in unstrained state) in air at 140/170/200 oC for 32 weeks. → Cross-link exchange, Joule-Gough effect and ionic interaction during ageing in unstrained state. → Enhanced physical/chemical degradation of compound during ageing under strain. → Capability of compound to withstand heat, radiation, air and mechanical load in reactor for 10 years. → Negligible chemical dose rate effect and gas evolution from compound during seal operation. -- Abstract: The development of a fluorohydrocarbon rubber compound for static backup seals of 500 MWe, Prototype Fast Breeder Reactor (PFBR) is depicted. Variations of a previously developed Viton A-401C based formulation were subjected to processability tests, accelerated heat ageing in air, mechanical characterization and production trials. Finite element analysis and literature data extrapolation were combined with long term ageing to ascertain the life (minimum 10 years) of chosen formulation in reactor under synergistic influences of 110 oC, 23 mGy/h (γ dose rate) and air considering postulated accidental conditions. Validation of test seals and quality assessment indicate that composition and properties of the validated laboratory compound has been translated effectively to the reactor seals, installed recently in PFBR. The tensile and hardness specimens indicated negligible degradation and exceptional thermo-oxidative stability of the seal compound during ageing (32 weeks at 140/170/200 oC) even though interesting manifestations of cross-link exchange and ionic interactions were observed. Compression set results, showing definite trends of change under ageing and stain, were used in Arrhenius and Williams Landel Ferry equations for realistic life prediction. The development provides a foundation to simplify and standardize the design, development and operation of major elastomeric sealing applications of Indian nuclear reactors based on a

  19. Evaluation of the Initial Isothermal Physics Measurements at the Fast Flux Test Facility, a Prototypic Liquid Metal Fast Breeder Reactor

    Energy Technology Data Exchange (ETDEWEB)

    John D. Bess

    2010-03-01

    The Fast Flux Test Facility (FFTF) was a 400-MWt, sodium-cooled, low-pressure, high-temperature, fast-neutron flux, nuclear fission reactor plant designed for the irradiation testing of nuclear reactor fuels and materials for the development of liquid metal fast breeder reactors (LMFBRs). The FFTF was fueled with plutonium-uranium mixed oxide (MOX) and reflected by Inconel-600. Westinghouse Hanford Company operated the FFTF as part of the Hanford Engineering Development Laboratory (HEDL) for the U.S. Department of Energy on the Hanford Site near Richland, Washington. Although the FFTF was a testing facility not specifically designed to breed fuel or produce electricity, it did provide valuable information for LMFBR projects and base technology programs in the areas of plant system and component design, component fabrication, prototype testing, and site construction. The major objectives of the FFTF were to provide a strong, disciplined engineering base for the LMFBR program, provide fast flux testing for other U.S. programs, and contribute to the development of a viable self-sustaining competitive U.S. LMFBR industry. During its ten years of operation, the FFTF acted as a national research facility to test advanced nuclear fuels, materials, components, systems, nuclear power plant operating and maintenance procedures, and active and passive reactor safety technologies; it also produced a large number of isotopes for medical and industrial users, generated tritium for the U.S. fusion research program, and participated in cooperative, international research work. Prior to the implementation of the reactor characterization program, a series of isothermal physics measurements were performed; this acceptance testing program consisted of a series of control rod worths, critical rod positions, subcriticality measurements, maximum reactivity addition rates, shutdown margins, excess reactivity, and isothermal temperature coefficient reactivity. The results of these

  20. A report on (interim) evaluation of research and development subjects in fiscal year 2000. Evaluation subject on the 'Safety research in fast breeder reactor'

    International Nuclear Information System (INIS)

    Safety research as a basis R and D supporting development of the fast breeder reactor (FBR) has been practiced at aims of development, admittance and operation/maintenance of a fast experimental reactor, 'Joyo' and a fast breeder prototype reactor, 'Monju' and of reflection to a proof reactor plan promoted by the electric utility. However, at present, in order to reflect FBR cycle actual use strategy survey research, decision of importance in research is promoted to effectively reflect their research results to judgment and investigation on consistency of various candidate concepts. Here was carried out on some evaluations on research program and practicing method of coming five years on conventional research results, reflection to the second period of the actual use strategy survey research, and practice of national safety research yearly plan at a center of past five years on contribution to FBR development and safety regulation in Japan. Here were described on aim and meaning of the R and D, establishment of target, planning, practicing system, and results. (G.K.)

  1. Fabrication of MOX Fuel elements for irradiation in Fast Breeder Test Reactor (FBTR)

    International Nuclear Information System (INIS)

    Advanced Fuel Fabrication Facility (AFFF), Bhabha Atomic Research Centre, Tarapur is fabricating Uranium - Plutonium Mixed Oxide Fuel (MOX) for different types of reactors. Recently MOX fuel pins for an experimental fuel subassembly of 37 pins has been fabricated for irradiation in Fast Breeder Test Reactor (FBTR) at Kalpakkam near Chennai. MOX fuel pins containing 44% PuO2 have also been also made for the hybrid core of FBTR. The experimental sub-assembly for irradiation testing in FBTR consisted of 37 short length Prototype Fast Breeder Reactor (PFBR) MOX fuel elements. The composition of the fuel was (0.71 U - 0.29 Pu) O2 with U233 O2 content of 53.5% of total UO2. Uranium enriched with U233 was used to simulate the heat flux of PFBR in FBTR neutron spectrum. MOX fuel pellets were made by powder metallurgy process consisting of pre-compaction, granulation, final compaction and sintering at high temperature. Initially U3233 O8 / U233 O3 powder was subjected to heat treatment. The pellets were sintered at reducing atmosphere at 1650oC for 4 hours to obtain acceptable quality pellets. Over sized pellets were centrelessly ground.without using a liquid coolant. During the fabrication of pins for experimental subassembly, technology was developed and conditions were optimized for making annular pellets, TIG welding of D9 tubes with SS 316 end plugs and wire wrapping. Quality control procedures and process control procedures at different stages of fabrication were developed. The hybrid core of FBTR consists of Mixed Carbide (MC) sub-assemblies containing (0.70 Pu - 0.30 U) C pellets and MOX fuel sub-assemblies containing (0.44 Pu - 0.56 U) O2. Studies were made to fabricate fuel containing higher percentage of Plutonium and the conditions were established. This paper describes the development of flowsheet for making annular MOX fuel pellets containing plutonium and U233, the technology for welding of D-9 clad tubes, wire wrapping and inspection. The paper also

  2. Advanced automation concepts applied to Experimental Breeder Reactor-II startup

    International Nuclear Information System (INIS)

    The major objective of this work is to demonstrate through simulations that advanced liquid-metal reactor plants can be operated from low power by computer control. Development of an automatic control system with this objective will help resolve specific issues and provide proof through demonstration that automatic control for plant startup is feasible. This paper presents an advanced control system design for startup of the Experimental Breeder Reactor-2 (EBR-2) located at Idaho Falls, Idaho. The design incorporates recent methods in nonlinear control with advanced diagnostics techniques such as neural networks to form an integrated architecture. The preliminary evaluations are obtained in a simulated environment by a low-order, valid nonlinear model. Within the framework of phase 1 research, the design includes an inverse dynamics controller, a fuzzy controller, and an artificial neural network controller. These three nonlinear control modules are designed to follow the EBR-2 startup trajectories in a multi-input/output regime. They are coordinated by a supervisory routine to yield a fault-tolerant, parallel operation. The control system operates in three modes: manual, semiautomatic, and fully automatic control. The simulation results of the EBR-2 startup transients proved the effectiveness of the advanced concepts. The work presented in this paper is a preliminary feasibility analysis and does not constitute a final design of an automated startup control system for EBR-2. 14 refs., 43 figs

  3. 03 - Sodium cooled fast breeder fourth-generation reactors - The technological demonstrator ASTRID

    International Nuclear Information System (INIS)

    After a discussion of the past experience gained on fast breeder reactors in the world (benefits, difficulties and problematics), the authors discuss the main improvement domains and the associated R and D advances (reactor safety, prevention and mitigation of severe accidents, the sodium-water risk, detection of sodium leaks, increased availability, instrumentation and inspection, control and repairability, assembly handling and washing). Then, they describe the technical requirements and safety objectives of the ASTRID experimental project, notably with its reactivity management, cooling management, and radiological containment management functions. They describe and discuss requirements to be met and choices made for Astrid, and the design options for its various components (core and fuels, nuclear heater, energy conversion system, fuel assembly handling, instrumentation and in-service inspection, control and command). They present the installations which are associated with the ASTRID cycle, evoke the development and use of simulations and codes, describe the industrial organization and the international collaboration about the ASTRID project, present the planning and cost definition

  4. Real Time Computer for Plugging Indicator Control of Prototype Fast Breeder Reactor

    International Nuclear Information System (INIS)

    Prototype Fast Breeder Reactor (PFBR) is in the advanced stage of construction at Kalpakkam, India. Liquid sodium is used as coolant to transfer the heat produced in the reactor core to steam water circuit. Impurities present in the sodium are removed using purification circuit. Plugging indicator is a device used to measure the purity of the sodium. Versa Module Europa bus based Real Time Computer (RTC) system is used for plugging indicator control. Hot standby architecture consisting of dual redundant RTC system with switch over logic system is the configuration adopted to achieve fault tolerance. Plugging indicator can be controlled in two modes namely continuous and discontinuous mode. Software based Proportional-Integral-Derivative (PID) algorithms are developed for plugging indicator control wherein the set point changes dynamically for every scan interval of the RTC system. Set points and PID constants are kept as configurable in runtime in order to control the process in very efficient manner, which calls for reliable communication between RTC system and control station, hence TCP/IP protocol is adopted. Performance of the RTC system for plugging indicator control was thoroughly studied in the laboratory by simulating the inputs and monitored the control outputs. The control outputs were also monitored for different PID constants. Continuous and discontinuous mode plots were generated. (authors)

  5. Design and fabrication of sodium test facility for fast breeder reactor

    International Nuclear Information System (INIS)

    The purpose of the promotion policy for energy research and development base construction plan (priority facility) of the Japanese government in FY2009 is 'to construct in Tsuruga City the research and development base for plant operation technology for the practical use of fast breeder reactor where researchers in and out of Japan gather, and to contribute to the development and revitalization of the region as the base with international characteristics.' In conformity to this purpose, the Japan Atomic Energy Agency built 'sodium engineering research facilities' in Tsuruga. This paper describes the design, fabrication, and installation of interior equipment that were carried out by Kawasaki Heavy Industries. 'Sodium engineering research facilities' are the test and research facilities to conduct research and development related to sodium, while reflecting the experiences of operation and maintenance of 'Monju,' which aims at the commercialization of fast reactor. The facilities specialize in the handling technology of sodium to meet the needs in and out of Japan, and were completed in June 2015. The facilities consist of six units including tank-loop test equipment, mini-loop test equipment, sodium purification and supply equipment, etc. For the tank-loop test equipment, a sodium transfer test of about 5.5 tons, and a subsequent comprehensive function test using sodium are scheduled. (A.O.)

  6. A ceramic breeder in a poloidal tube blanket for a tokamak reactor

    Energy Technology Data Exchange (ETDEWEB)

    Amici, A.; Anzidei, L.; Gallina, M.; Rado, V.; Simbolotti, G.; Violante, V.; Zampaglione, V.; Petrizzi, L. (Associazione Euratom-CNEN sulla Fusione, Centro di Frascati (Italy))

    1989-04-01

    A conceptual study of a helium-cooled solid breeder blanket for a tokamak reactor is presented. Tritium breeding capability together with system reliability are taken as the main design criteria. The blanket consists of tubular poloidal modules made of a central bundle of ceramic rods ({gamma}LiAlO/sub 2/) with a coaxial distribution of the inlet/outlet coolant flow (He) surrounded by a multiplier material (Be) in the form of bored bricks. The Be to {gamma}LiAlO/sub 2/ volume ratio is 4/1. The He inlet and outlet branches are cooling Be and {gamma}LiAlO/sub 2/, respectively. A purge He flow running through small central holes of the ceramic rods is derived from the main flow. Under the typical conditions of a tokamak reactor (neutron wall load=2 MW/m/sup 2/), a full coverage tritium breeding ratio of 1.47 is achieved for the following design and operating parameters: outlet He temperature=570/sup 0/C; inlet He temperature=250/sup 0/; total extracted power=2700 MW; He pumping power percentage=2%; minimum/maximum {gamma}LiAlO/sub 2/ temperature=400/900/sup 0/C; maximum structural temperature=475/sup 0/C; and maximum Be temperature=525/sup 0/C. (orig.).

  7. Reliability analysis of safety grade decay heat removal system of Indian prototype fast breeder reactor

    International Nuclear Information System (INIS)

    The 500 MW Indian pool type Prototype Fast Breeder Reactor (PFBR), is provided with two independent and diverse Decay Heat Removal (DHR) systems viz., Operating Grade Decay Heat Removal System (OGDHRS) and Safety Grade Decay Heat Removal System (SGDHRS). OGDHRS utilizes the secondary sodium loops and Steam-Water System with special decay heat removal condensers for DHR function. The unreliability of this system is of the order of 0.1-0.01. The safety requirements of the present generation of fast reactors are very high, and specifically for DHR function the failure frequency should be less than ∼1E-7/ry. Therefore, a passive SGDHR system using four completely independent thermo-siphon loops in natural convection mode is provided to ensure adequate core cooling for all Design Basis Events. The very high reliability requirement for DHR function is achieved mainly with the help of SGDHRS. This paper presents the reliability analysis of SGDHR system. Analysis is performed by Fault Tree method using 'CRAFT' software developed at Indira Gandhi Centre for Atomic Research. This software has special features for compact representation and CCF analysis of high redundancy safety systems encountered in nuclear reactors. Common Cause Failures (CCF) are evaluated by β factor method. The reliability target for SGDHRS arrived from DHR reliability requirement and the ultimate number of demands per year (7/y) on SGDHRS is that the failure frequency should be ≤1.4E-8/de. Since it is found from the analysis that the unreliability of SGDHRS with identical loops is 5.2E-6/de and dominated by leak rates of components like AHX, DHX and sodium dump and isolation valves, options with diversity measures in important components were studied. The failure probability of SGDHRS for a design consisting of 2 types of diverse loops (Diverse AHX, DHX and sodium dump and isolation valves) is 2.1E-8/de, which practically meets the reliability requirement

  8. Fast breeder reactor blanket management: comparison of LMFBR and GCFR blankets

    International Nuclear Information System (INIS)

    The economic performance of the fast breeder reactor blanket, considering different fuel management schemes was studied. To perform this, the investigation started with a standard reactor physics calculation. Then, two economic models for evaluation of the economic performance of the radial blanket were developed. These models formed the basis of a computer code, ECOBLAN, which computes the net economic gain and the levelized fuel cost due to the radial blanket. The net gain in terms of dollars and $/kgHM-y and the levelized fuel cost in mills/kWhe were obtained as a function of blanket thickness and a residence time of the fuel in the blanket. A LMFBR and a GCFR were the reactor models considered in this study. The optimum radial blanket of a GCFR consists of two rows, that of a LMFBR consists of three rows. Regarding the different fuel management schemes, the fixed blanket was found to be more favorable than reshuffled blanket. Out-in and in-out reshuffled blanket offer almost the same net gain. In all the cases, the burnup calculated for the fuel was found to be less than the acceptable limit. There is an optimum residence time for the fuel in the blanket which depends on the position of the fuel in the blanket and the fuel management scheme studied. As expected, except for very short residence times (less than 2.5 years), the radial blanket is a net income producer. There is no significant difference between the economic performance of the blanket of a LMFBR and a GCFR

  9. Integral Fast Reactor Program

    International Nuclear Information System (INIS)

    This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1992. Technical accomplishments are presented in the following areas of the IFR technology development activities: (1) metal fuel performance, (2) pyroprocess development, (3) safety experiments and analyses, (4) core design development, (5) fuel cycle demonstration, and (6) LMR technology R ampersand D

  10. Performance characterization of geopolymer composites for hot sodium exposed sacrificial layer in fast breeder reactors

    Energy Technology Data Exchange (ETDEWEB)

    Haneefa, K. Mohammed, E-mail: mhkolakkadan@gmail.com [Department of Civil Engineering, IIT Madras, Chennai (India); Santhanam, Manu [Department of Civil Engineering, IIT Madras, Chennai (India); Parida, F.C. [Radiological Safety Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

    2013-12-15

    Highlights: • Performance evaluation of geopolymers subjected to hot liquid sodium is performed. • Apart from mechanical properties, micro-analytical techniques are used for material characterization. • The geopolymer composite showed comparatively lesser damage than conventional cement composites. • Geopolymer technology can emerge as a new choice for sacrificial layer in SCFBRs. - Abstract: A sacrificial layer of concrete is used in sodium cooled fast breeder reactors (SCFBRs) to mitigate thermo-chemical effect of accidentally spilled sodium at and above 550 °C on structural concrete. Performance of this layer is governed by thermo-chemical stability of the ingredients of sacrificial layer concrete. Concrete with limestone aggregate is generally used as a sacrificial layer. Conventional cement based systems exhibit instability in hot liquid sodium environment. Geo-polymer composites are well known to perform excellently at elevated temperatures compared to conventional cement systems. This paper discusses performance of such composites subjected to exposure of hot liquid sodium in air. The investigation includes comprehensive evaluation of various geo-polymer composites before any exposure, after heating to 550 °C in air, and after immersing in hot liquid sodium initially heated to 550 °C in air. Results from the current study indicate that hot liquid sodium produces less damage to geopolymer composites than to the existing conventional cement based system. Hence, the geopolymer technology has potential application in mitigating the degrading effects of sodium fires and can emerge as a new choice for sodium exposed sacrificial layer in SCFBRs.

  11. Stress Analysis of Steam Generator Shell Nozzle Junction for Sodium cooled Fast Breeder Reactor

    Directory of Open Access Journals (Sweden)

    Mani N,

    2010-07-01

    Full Text Available The Steam Generators (SG decides the capacity factor in Sodium cooled Fast breeder Reactor (SFR plants and hence they are designed with high reliability. One of the critical locations in SG is the shell nozzle junction. This junction is subjected to an end bending moment and internal pressure. Since the shell nozzle junction is the critical location of SG a double-ended guillotine rupture will result in leakage of large quantity of sodium, which is not desirable. The material of construction is modified 9Cr-1Mo. Hence safety equirements demand that Leak Before Break criteria with assumed initial flaw have to be demonstrated. To demonstrate LBB, the basic requirement is to predict the state of stress precisely in the shell nozzle junction under various loading conditions. An efficient finiteelement modeling for shell nozzle junction has been presented in which shell elements are employed to idealize the whole region. These results are used for the analysis of leak before break concept.

  12. A study of parameters on marking of Prototype Fast Breeder Reactor fuel elements

    International Nuclear Information System (INIS)

    Prototype Fast Breeder Reactor Fuel (PFBR) elements are identified with a permanent unique marking. Identification of the fuel elements is very much necessary for traceability during initial fabrication as well as for post irradiation examination. Marking on fuel element has to be permanent and capable of being identified after irradiation. Laser marking is a relatively new method as compared to other marking technologies such as ink marking, mechanical engraving and electro chemical methods. It is used for the product identification and traceability during its service life. Laser marking has many advantages compared to other conventional marking. In laser marking process, mark quality is a very important factor, which depends on so many variables like input current, pulse frequency, marking speed and number of passes. The influence of the pulse frequency and the speed of travel of the laser beam on the mark depth and width have been studied in this paper. An optical microscope, scanning electron microscope were used to measure the effects of pulse frequency on the mark depth and width. It has been found that the mark depth and width depend on the interaction process of the laser beam and the material, which was influenced by the pulse frequency. Micro hardness testing is carried out to report Heat Affected Zone (HAZ) variation with parameters. Marking speed and input current selected for suitable depth and width were mentioned in the present study. (author)

  13. Blowdown transient for sodium-steam water SG for prototype fast breeder reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lele, H.G.; Srivastava, A.; Majumdar, P.; Mukhopadhyay, D.; Gupta, S.K. [Reactor Safety Div., Bhabha Atomic Research Centre, Tromblay (India); Chetal, S.C. [Indira Gandhi Centre for Atomic Research, Associate Director, Reactor Group, Chennai (India)

    2001-07-01

    Prototype Fast Breeder Test Reactor (PFBR) Steam Generator is once through steam generator in which water flows from bottom to top in 547 tubes, changing its state from highly subcooled to superheated state as it receives heat from sodium flowing from top to bottom in the shell side. Depressurization of steam generator from the dump valve provided at bottom is protective action. It prevents further possibility of water steam leak into sodium and subsequent sodium - water reaction. To perform depressurization transient analysis of PFBR appropriate thermal hydraulic modeling of SG is essential. Correct thermal hydraulic modelling needs simulation of sodium system, steam water system with different states from highly subcooled to superheated, coupling between sodium and steam-water system, SG tube and shell and different valve action. The computer code DPPFBR is developed with capability to simulate all these systems and phenomena encountered during transient. Different models of the code have been validated and code has been used for analysing depressurization transient. This paper describes various models used in the code and results of analysis for typical scenario. (author)

  14. Engineering development studies for molten-salt breeder reactor processing No. 18

    International Nuclear Information System (INIS)

    A water--mercury system was used to study the effect of geometric variations on mass transfer rates in rectangular contractors similar to those proposed for the molten-salt breeder reactor (MSBR) fuel reprocessing scheme. Since mass transfer rates were not accurately predicted by the Lewis correlation, other correlations were investigated. A correlation which was found to fit the experimental results is given. Mass transfer rates are being measured in a fluoride salt--bismuth contactor. Experimental results indicate that the mass transfer rates in the salt--bismuth system fall between the Lewis correlation and the modified correlation given above. Autoresistance heating tests were continued in the fluorinator mock-up using LiF--BeF2--ThF4 (72-16-12 mole percent) salt. The equipment was returned to operating condition, and five experiments were run. Although correct steady-state operation was not achieved, the results were encouraging. A two-dimensional electrical analog was constructed to study current flow through the electrode sidearm and other critical areas of the test vessel. These studies indicate that no regions of abnormally high current density existed in the first nine runs with the present autoresistance heating equipment. Localized heating had previously been the suspected cause for the failure to achieve proper operation of this equipment. (U.S.)

  15. Development of an ISI robot for the fast breeder reactor MONJU primary heat transfer system piping

    International Nuclear Information System (INIS)

    This paper describes the development of a new inspection robot for the In-Service Inspection of the heat transfer system of the Fast Breeder Reactor MONJU. The inspection was carried out using a tire-type ultrasonic sensor for volumetric tests at high temperature (atmosphere, 55degC; piping surface, 80degC) and radiation exposure condition (dose rate, 10 mGy/h; piping surface dose rate, 15 mGy/h). An inspection robot using a new tire type for the ultrasonic testing sensor and a new control method was developed. A signal-to-noise ratio S/N over 2 was obtained during the functional test for a calibration defect with a depth of 50%t (from the tube wall thickness). In the automatic inspection test, an EDM slit with a depth of 9% from the pipe thickness was detectable and with an S/N ratio = 4.0 (12.0 dB). (author)

  16. Tridimensional ultrasonic images analysis for the in service inspection of fast breeder reactors

    International Nuclear Information System (INIS)

    Tridimensional image analysis provides a set of methods for the intelligent extraction of information in order to visualize, recognize or inspect objects in volumetric images. In this field of research, we are interested in algorithmic and methodological aspects to extract surface visual information embedded in volume ultrasonic images. The aim is to help a non-acoustician operator, possibly the system itself, to inspect surfaces of vessel and internals in Fast Breeder Reactors (FBR). Those surfaces are immersed in liquid metal, what justifies the ultrasonic technology choice. We expose firstly a state of the art on the visualization of volume ultrasonic images, the methods of noise analysis, the geometrical modelling for surface analysis and finally curves and surfaces matching. These four points are then inserted in a global analysis strategy that relies on an acoustical analysis (echoes recognition), an object analysis (object recognition and reconstruction) and a surface analysis (surface defects detection). Few literature can be found on ultrasonic echoes recognition through image analysis. We suggest an original method that can be generalized to all images with structured and non-structured noise. From a technical point of view, this methodology applied to echoes recognition turns out to be a cooperative approach between morphological mathematics and snakes (active contours). An entropy maximization technique is required for volumetric data binarization. (author)

  17. Calculations of sodium aerosol concentrations at breeder reactor air intake ports

    International Nuclear Information System (INIS)

    This report describes the methodology used and results obtained in efforts to estimate the sodium aerosol concentrations at air intake ports of a liquid-metal cooled, fast-breeder nuclear reactor. A range of wind speeds from 2 to 10 m/s is assumed, and an effort is made to include building wake effects which in many cases dominate the dispersal of aerosols near buildings. For relatively small release rates on the order of 1 to 10 kg/s, it is suggested that the plume rise will be small and that estimates of aerosol concentrations may be derived using the methodology of Wilson and Britter (1982), which describes releases from surface vents. For more acute releases with release rates on the order of 100 kg/s, much higher release velocities are expected, and plume rise must be considered. Both momentum-driven and density-driven plume rise are considered. An effective increase in release height is computed using the Split-H methodology with a parameterization suggested by Ramsdell (1983), and the release source strength was transformed to rooftop level. Evaluation of the acute release aerosol concentration was then based on the methodology for releases from a surface release of this transformed source strength

  18. Clinch River Breeder Reactor environmental effects: general water-side corrosion

    International Nuclear Information System (INIS)

    Studies are described of the general corrosion of 21/4 Cr--1 Mo steel in pure superheated steam, in impure superheated and saturated steam, and under nucleate boiling conditions. The test parameters were selected to provide information relevant to the use of this steel for the Clinch River Breeder Reactor superheaters and evaporators. The oxidation rate of 21/4 Cr--1 Mo steel in superheated steam was measured under heat transfer conditions at 510 to 5400C (950 to 10050F), and was approximately 11/2 times that measured under isothermal conditions. Extensive general attack of stressed 21/4 Cr--1 Mo steel specimens occurred in cyclic tests in superheated and saturated steam with chloride and oxygen additions, although no cracking or localized attack was observed. Considerably less attack occurred under superheat conditions or in the absence of oxygen. Tests under nucleate boiling conditions were operated to evaluate crevice effects associated with porous films on heat transfer surfaces. Significant crevice corrosion was produced in water containing 10 ppm chloride; a heavier but more general attack occurred in treated cooling tower water

  19. Thermal hydraulics in the hot pool of Fast Breeder Test Reactor

    International Nuclear Information System (INIS)

    Sodium cooled Fast Breeder Test Reactor (FBTR) of 40 MWt/13 MWe capacity is in operation at Kalpakkam, near Chennai. Presently it is operating with a core of 10.5 MWt. Knowledge of temperatures and flow pattern in the hot pool of FBTR is essential to assess the thermal stresses in the hot pool. While theoretical analysis of the hot pool has been conducted by a three-dimensional code to access the temperature profile, it involves tuning due to complex geometry, thermal stresses and vibration. With this in view, an experimental model was fabricated in 1/4 scale using acrylic material and tests were conducted in water. Initially hydraulic studies were conducted with ambient water maintaining Froude number similarity. After that thermal studies were conducted using hot and cold water maintaining Richardson similitude. In both cases Euler similarity was also maintained. Studies were conducted simulating both low and full power operating conditions. This paper discusses the model simulation, similarity criteria, the various thermal hydraulic studies that were carried out, the results obtained and the comparison with the prototype measurements.

  20. Blowdown transient for sodium-steam water SG for prototype fast breeder reactor

    International Nuclear Information System (INIS)

    Prototype Fast Breeder Test Reactor (PFBR) Steam Generator is once through steam generator in which water flows from bottom to top in 547 tubes, changing its state from highly subcooled to superheated state as it receives heat from sodium flowing from top to bottom in the shell side. Depressurization of steam generator from the dump valve provided at bottom is protective action. It prevents further possibility of water steam leak into sodium and subsequent sodium - water reaction. To perform depressurization transient analysis of PFBR appropriate thermal hydraulic modeling of SG is essential. Correct thermal hydraulic modelling needs simulation of sodium system, steam water system with different states from highly subcooled to superheated, coupling between sodium and steam-water system, SG tube and shell and different valve action. The computer code DPPFBR is developed with capability to simulate all these systems and phenomena encountered during transient. Different models of the code have been validated and code has been used for analysing depressurization transient. This paper describes various models used in the code and results of analysis for typical scenario. (author)

  1. Crystal chemistry of immobilization of fast breeder reactor (FBR) simulated waste in sodium zirconium phosphate (NZP) ceramic matrix

    Energy Technology Data Exchange (ETDEWEB)

    Chourasia, Rashmi [Department of Chemistry, Dr. H.S. Gour University, Sagar 470 003 (India); Shrivastava, O.P., E-mail: dr_ops11@rediffmail.co [Department of Chemistry, Dr. H.S. Gour University, Sagar 470 003 (India); Ambashta, R.D.; Wattal, P.K. [Bhabha Atomic Research Centre, Trombay, Mumbai 400 085 (India)

    2010-02-15

    Fuel from the fast breeder reactor waste is reprocessed and subjected to cooling for a period of about one year. Fission and activation products of the fuel are the major constituents of this waste. Sodium zirconium phosphate (hereafter NZP) has been identified as a potential material for immobilization of long lived heat generating radio nuclides. It was found that most of the elements present in the radioactive waste could be immobilized in this ceramic matrix without significant changes of the three-dimensional framework of the host material. Simulated NZP waste forms synthesized by ceramic route at 1200 deg. C crystallize in the rhombohedral system (space group R-3c). The crystal chemistry of 0-35 wt.% waste loaded NZP waste forms have been investigated using General Structure Analysis System (GSAS) programming of the step analysis powder diffraction data. Rietveld refinement of crystal data on the waste oxide (WO{sub x}) loaded waste forms gives a satisfactory convergence of R-factors. The particle size along prominent reflecting planes ranges between 68 and 141 nm. The polyhedral distortions and effective valence calculations from bond strength data are also reported. Morphological examination by scanning electron microscopy (SEM) reveals that the size of almost rectangular parallelepiped shaped grains varies between 0.2 and 5 mum. The EDX analysis provides analytical evidence of immobilization of effluent cations in the matrix.

  2. Theoretical and experimental studies of non-linear structural dynamics of fast breeder reactor fuel elements

    International Nuclear Information System (INIS)

    Descriptions are presented of theoretical and experimental studies of the deformation behaviour of fast-breeder fuel elements as a consequence of extreme impulsive stresses produced by an incident. The starting point for the studies is the assumption that local disturbances in a fuel element have resulted in a thermal interaction between fuel and sodium and in a corresponding increase in pressure. On the basis of the current state of knowledge, the possibility cannot be ruled out that this pressure build-up may lead to the bursting of the fuel-element wrapper, to the propagation of pressure in the core, and to coherent structural movements and deformations. A physical model is established for the calculation of the dynamic response of elastic-plastic beam systems, and the differential equations of p motion for the discrete equivalent system are derived with the aid of D'Alembert's principle. On this basis and with the aid of a semi-empirical pin-bundle model, an appropriate computer program allows a static and dynamic analysis to be obtained for a complete fuel element. In the experimental part of the study, a description is given of static and impulsive loading tests on 1:1 SNR-like fuel-element models. Making use of measured impact forces and of known material characteristics, it was possible to a large extent for the experiments to be reproduced by calculations. In agreement with existing experience from explosion experiments on 1:1 core models, the results (of relevance for fast-breeder safety and in particular the SNR-300) show that only local limited deformations occur and that the compact fuel-element and core structure constitutes an effective inherent barrier in the presence of extreme incident stresses. (author)

  3. Progress in studies of Li/sub 17/Pb/sub 83/ as liquid breeder for fusion reactor blankets

    Energy Technology Data Exchange (ETDEWEB)

    Casini, G.

    1983-09-01

    A review of the experimental and conceptual design work in progress at JRC-Ispra to investigate the feasibility of the eutectic Li/sub 17/Pb/sub 83/ as a liquid breeder for experimental power reactors is presented. Results of recent measurements to implement the data base of this material are given in the following areas: physical parameters, hydrogen solubility and recovery, chemical reactivity with air and water, compatibility with steel. The studies carried out on blanket concepts for the INTOR (International Tokamak Reactor)/NET (Next European Torus) projects are outlined and discussed.

  4. Safety-Evaluation Report related to the construction of the Clinch River Breeder Reactor Plant. Docket No. 50-537

    International Nuclear Information System (INIS)

    The Safety-Evaluation Report for the application by the United States Department of Energy, Tennessee Valley Authority, and the Project Management Corporation, as applicants and owners, for a license to construct the Clinch River Breeder Reactor Plant (docket No. 50-537) has been prepared by the Office of Nuclear Reactor Regulation of the United States Nuclear Regulatory Commission. The facility will be located on the Clinch River approximately 12 miles southwest of downtown Oak Ridge and 25 miles west of Knoxville, Tennessee. Subject to resolution of the items discussed in this report, the staff concludes that the construction permit requested by the applicants should be issued

  5. Breeder Reprocessing Engineering Test

    Energy Technology Data Exchange (ETDEWEB)

    Burgess, C.A.; Meacham, S.A.

    1984-01-01

    The Breeder Reprocessing Engineering Test (BRET) is a developmental activity of the US Department of Energy to demonstrate breeder fuel reprocessing technology while closing the fuel cycle for the Fast Flux Test Facility (FFTF). It will be installed in the existing Fuels and Materials Examination Facility (FMEF) at the Hanford Site near Richland, Washington, The major objectives of BRET are: (1) close the US breeder fuel cycle; (2) develop and demonstrate reprocessing technology and systems for breeder fuel; (3) provide an integrated test of breeder reactor fuel cycle technology - rprocessing, safeguards, and waste management. BRET is a joint effort between the Westinghouse Hanford Company and Oak Ridge National Laboratory. 3 references, 2 figures.

  6. Choice of rotatable plug seals for prototype fast breeder reactor: Review of historical perspectives

    International Nuclear Information System (INIS)

    Highlights: • Choice and arrangement of elastomeric inflatable and backup seals as primary and secondary barriers. • With survey (mid-1930s onwards) of reactor, sealing, R&D and rubber technology. • Load, reliability, safety, life and economy of seals and reactors are key factors. • PFBR blends concepts and experience of MOX fuelled FBRs with original solutions. • R&D indicates inflatable seal advanced fluoroelastomer pivotal in unifying nuclear sealing. - Abstract: Choice and arrangement of elastomeric primary inflatable and secondary backup seals for the rotatable plugs (RPs) of 500 MW (e), sodium cooled, pool type, 2-loop, mixed oxide (MOX) fuelled Prototype Fast Breeder Reactor (PFBR) is depicted with review of various historical perspectives. Static and dynamic operation, largest diameters (PFBR: ∼6.4 m, ∼4.2 m), widest gaps and variations (5 ± 2 mm) and demanding operating requirements make RP openings on top shield (TS) the most difficult to seal which necessitated extensive development from 1950s to early 1990s. Liquid metal freeze seals with life equivalent to reactor prevailed as primary barrier (France, Japan, U.S.S.R.) during pre-1980s in spite of bulk, cost and complexity due to the abilities to meet zero leakage and resist core disruptive accident (CDA). Redefinition of CDA as beyond design basis accident, tolerable leakage and enhanced economisation drive during post-1980s established elastomeric inflatable seal as primary barrier excepting in U.S.S.R. (MOX fuel, freeze seal) and U.S.A. (metallic fuel). Choice of inflatable seal for PFBR RPs considers these perspectives, inherent advantages of elastomers and those of inflatable seals which maximise seal life. Choice of elastomeric backup seal as secondary barrier was governed by reliability and minimisation as well as distribution of load (temperature, radiation, mist) to maximise seal life. The compact sealing combination brings the hanging RPs at about the same elevation to reduce

  7. Choice of rotatable plug seals for prototype fast breeder reactor: Review of historical perspectives

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, N.K., E-mail: nksinha@igcar.gov.in; Raj, Baldev, E-mail: baldev.dr@gmail.com

    2015-09-15

    Highlights: • Choice and arrangement of elastomeric inflatable and backup seals as primary and secondary barriers. • With survey (mid-1930s onwards) of reactor, sealing, R&D and rubber technology. • Load, reliability, safety, life and economy of seals and reactors are key factors. • PFBR blends concepts and experience of MOX fuelled FBRs with original solutions. • R&D indicates inflatable seal advanced fluoroelastomer pivotal in unifying nuclear sealing. - Abstract: Choice and arrangement of elastomeric primary inflatable and secondary backup seals for the rotatable plugs (RPs) of 500 MW (e), sodium cooled, pool type, 2-loop, mixed oxide (MOX) fuelled Prototype Fast Breeder Reactor (PFBR) is depicted with review of various historical perspectives. Static and dynamic operation, largest diameters (PFBR: ∼6.4 m, ∼4.2 m), widest gaps and variations (5 ± 2 mm) and demanding operating requirements make RP openings on top shield (TS) the most difficult to seal which necessitated extensive development from 1950s to early 1990s. Liquid metal freeze seals with life equivalent to reactor prevailed as primary barrier (France, Japan, U.S.S.R.) during pre-1980s in spite of bulk, cost and complexity due to the abilities to meet zero leakage and resist core disruptive accident (CDA). Redefinition of CDA as beyond design basis accident, tolerable leakage and enhanced economisation drive during post-1980s established elastomeric inflatable seal as primary barrier excepting in U.S.S.R. (MOX fuel, freeze seal) and U.S.A. (metallic fuel). Choice of inflatable seal for PFBR RPs considers these perspectives, inherent advantages of elastomers and those of inflatable seals which maximise seal life. Choice of elastomeric backup seal as secondary barrier was governed by reliability and minimisation as well as distribution of load (temperature, radiation, mist) to maximise seal life. The compact sealing combination brings the hanging RPs at about the same elevation to reduce

  8. Startup of the FFTF sodium cooled reactor. [Acceptance Test Program

    Energy Technology Data Exchange (ETDEWEB)

    Redekopp, R.D.; Umek, A.M.

    1981-03-01

    The Fast Flux Test Facility (FFTF), located on the Department of Energy (DOE) Hanford Reservation near Richland, Washington, is a 3 Loop 400 MW(t) sodium cooled fast reactor with a primary mission to test fuels and materials for development of the Liquid Metal Fast Breeder Reactor (LMFBR). Bringing FFTF to a condition to accomplish this mission is the goal of the Acceptance Test Program (ATP). This program was the mechanism for achieving startup of the FFTF. Highlights of the ATP involving the system inerting, liquid metal and inerted cell testing and initial ascent to full power are discussed.

  9. Deterioration of limestone aggregate mortars by liquid sodium in fast breeder reactor environment

    Energy Technology Data Exchange (ETDEWEB)

    Mohammed Haneefa, K., E-mail: mhkolakkadan@gmail.com [Department of Civil Engineering, IIT Madras, Chennai (India); Santhanam, Manu [Department of Civil Engineering, IIT Madras, Chennai (India); Parida, F.C. [Radiological Safety Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

    2014-08-15

    Highlights: • Limestone mortars were exposed to liquid sodium exposure at 550 °C. • Micro-analytical techniques were used to characterize the exposed specimens. • The performance of limestone mortar was greatly influenced by w/c. • The fundamental degradation mechanisms of limestone mortars were identified. - Abstract: Hot liquid sodium at 550 °C can interact with concrete in the scenario of an accidental spillage of sodium in liquid metal cooled fast breeder reactors. To protect the structural concrete from thermo-chemical degradation, a sacrificial layer of limestone aggregate concrete is provided over it. This study investigates the fundamental mechanisms of thermo-chemical interaction between the hot liquid sodium and limestone mortars at 550 °C for a duration of 30 min in open air. The investigation involves four different types of cement with variation of water-to-cement ratios (w/c) from 0.4 to 0.6. Comprehensive analysis of experimental results reveals that the degree of damage experienced by limestone mortars displayed an upward trend with increase in w/c ratios for a given type of cement. Performance of fly ash based Portland pozzolana cement was superior to other types of cements for a w/c of 0.55. The fundamental degradation mechanisms of limestone mortars during hot liquid sodium interactions include alterations in cement paste phase, formation of sodium compounds from the interaction between solid phases of cement paste and aggregate, modifications of interfacial transition zone (ITZ), decomposition of CaCO{sub 3}, widening and etching of rhombohedral cleavages, and subsequent breaking through the weakest rhombohedral cleavage planes of calcite, staining, ferric oxidation in grain boundaries and disintegration of impurity minerals in limestone.

  10. Development of electromagnetic pumps for natrium coolant of liquid metal fast breeder reactor (2)

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Sang Hee; Su, Soo Won; Kin, Hee Lyeong; Lee, Sang Doo; Seo, Joom Ho [Electrical Engineering and Science Research Institute, Seoul (Korea, Republic of)

    1994-07-15

    Present work on the development of annular linear induction pumps of externally-supported-duct type are to create domestic electromagnetic pumps by our own design and manufacturing technique and to secure the technological experience and data for the production of large scale electromagnetic pumps for natrium coolant loop system of liquid metal fast breeder reactor in the future. Two annular induction pumps, a small-sized one of 400 deg C and 60 l/min and a medium-sized one of 600 deg C and 800 l/min for their maximum operating temperatures and flowrates, respectively, are designed and fabricated. Conceptual and detailed designs for annular linear induction pumps with 60 l/min and 800 l/min flowrates, respectively, have been done by finding the optimum geometrical and operational parameters based on an equivalent-circuit analysis method. The measurements of the flowrates and pressures of the assembled pumps are done for confirming their characteristics and performance and comparing electrical input powers with those obtained from calculations. The cooling method developed in this study can be used in parallel with natural convection cooling without compressed air injection, and improves cooling efficiency and simplification of the pump structure. Experimental results measured by a free-fall indirect method and a EM flowmeter are and the design value of flowrate of each pump is confirmed by comparing measured one from indirect measurements. A center-return type pump for visualizing natrium pumping are also built with one pole pitch, eight outer core versions and six slots. Its natrium loop for pumping exhibition is assembled with instruments, heating equipment, leak sensing and pneumatic valve, and operated by a remote control. Magnetic flux distribution analysis is performed analytically and numerically for axial and radial directions in each case with or without end effects and consequently finds electromagnetic body force and pump efficiency.

  11. Level monitoring system with pulsating sensor--application to online level monitoring of dashpots in a fast breeder reactor.

    Science.gov (United States)

    Malathi, N; Sahoo, P; Ananthanarayanan, R; Murali, N

    2015-02-01

    An innovative continuous type liquid level monitoring system constructed by using a new class of sensor, viz., pulsating sensor, is presented. This device is of industrial grade and it is exclusively used for level monitoring of any non conducting liquid. This instrument of unique design is suitable for high resolution online monitoring of oil level in dashpots of a sodium-cooled fast breeder reactor. The sensing probe is of capacitance type robust probe consisting of a number of rectangular mirror polished stainless steel (SS-304) plates separated with uniform gaps. The performance of this novel instrument has been thoroughly investigated. The precision, sensitivity, response time, and the lowest detection limit in measurement using this device are level is studied and the temperature compensation is provided in the instrument. The instrument qualified all recommended tests, such as environmental, electromagnetic interference and electromagnetic compatibility, and seismic tests prior to its deployment in nuclear reactor. With the evolution of this level measurement approach, it is possible to provide dashpot oil level sensors in fast breeder reactor for the first time for continuous measurement of oil level in dashpots of Control & Safety Rod Drive Mechanism during reactor operation. PMID:25725884

  12. Level monitoring system with pulsating sensor—Application to online level monitoring of dashpots in a fast breeder reactor

    Science.gov (United States)

    Malathi, N.; Sahoo, P.; Ananthanarayanan, R.; Murali, N.

    2015-02-01

    An innovative continuous type liquid level monitoring system constructed by using a new class of sensor, viz., pulsating sensor, is presented. This device is of industrial grade and it is exclusively used for level monitoring of any non conducting liquid. This instrument of unique design is suitable for high resolution online monitoring of oil level in dashpots of a sodium-cooled fast breeder reactor. The sensing probe is of capacitance type robust probe consisting of a number of rectangular mirror polished stainless steel (SS-304) plates separated with uniform gaps. The performance of this novel instrument has been thoroughly investigated. The precision, sensitivity, response time, and the lowest detection limit in measurement using this device are level is studied and the temperature compensation is provided in the instrument. The instrument qualified all recommended tests, such as environmental, electromagnetic interference and electromagnetic compatibility, and seismic tests prior to its deployment in nuclear reactor. With the evolution of this level measurement approach, it is possible to provide dashpot oil level sensors in fast breeder reactor for the first time for continuous measurement of oil level in dashpots of Control & Safety Rod Drive Mechanism during reactor operation.

  13. Level monitoring system with pulsating sensor—Application to online level monitoring of dashpots in a fast breeder reactor

    Energy Technology Data Exchange (ETDEWEB)

    Malathi, N.; Sahoo, P., E-mail: sahoop@igcar.gov.in; Ananthanarayanan, R.; Murali, N. [Real Time Systems Division, Electronics, Instrumentation and Radiological Safety Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)

    2015-02-15

    An innovative continuous type liquid level monitoring system constructed by using a new class of sensor, viz., pulsating sensor, is presented. This device is of industrial grade and it is exclusively used for level monitoring of any non conducting liquid. This instrument of unique design is suitable for high resolution online monitoring of oil level in dashpots of a sodium-cooled fast breeder reactor. The sensing probe is of capacitance type robust probe consisting of a number of rectangular mirror polished stainless steel (SS-304) plates separated with uniform gaps. The performance of this novel instrument has been thoroughly investigated. The precision, sensitivity, response time, and the lowest detection limit in measurement using this device are <0.01 mm, ∼100 Hz/mm, ∼1 s, and ∼0.03 mm, respectively. The influence of temperature on liquid level is studied and the temperature compensation is provided in the instrument. The instrument qualified all recommended tests, such as environmental, electromagnetic interference and electromagnetic compatibility, and seismic tests prior to its deployment in nuclear reactor. With the evolution of this level measurement approach, it is possible to provide dashpot oil level sensors in fast breeder reactor for the first time for continuous measurement of oil level in dashpots of Control and Safety Rod Drive Mechanism during reactor operation.

  14. Level monitoring system with pulsating sensor--application to online level monitoring of dashpots in a fast breeder reactor.

    Science.gov (United States)

    Malathi, N; Sahoo, P; Ananthanarayanan, R; Murali, N

    2015-02-01

    An innovative continuous type liquid level monitoring system constructed by using a new class of sensor, viz., pulsating sensor, is presented. This device is of industrial grade and it is exclusively used for level monitoring of any non conducting liquid. This instrument of unique design is suitable for high resolution online monitoring of oil level in dashpots of a sodium-cooled fast breeder reactor. The sensing probe is of capacitance type robust probe consisting of a number of rectangular mirror polished stainless steel (SS-304) plates separated with uniform gaps. The performance of this novel instrument has been thoroughly investigated. The precision, sensitivity, response time, and the lowest detection limit in measurement using this device are temperature on liquid level is studied and the temperature compensation is provided in the instrument. The instrument qualified all recommended tests, such as environmental, electromagnetic interference and electromagnetic compatibility, and seismic tests prior to its deployment in nuclear reactor. With the evolution of this level measurement approach, it is possible to provide dashpot oil level sensors in fast breeder reactor for the first time for continuous measurement of oil level in dashpots of Control & Safety Rod Drive Mechanism during reactor operation.

  15. Social and ethical aspects of the liquid-metal fast breeder reactor

    International Nuclear Information System (INIS)

    Development of liquid fast breeder reactors not only indirectly entails (through commitments of time and resources that foreclose other options), but also directly entails large-scale centralized electrification. The massive economic commitments of such a policy, wether or not it is a nuclear policy, demand and cause major social changes, bypass traditional market mechanisms, concentrate political and economic power, persistently distort political structures and social priorities, compromise professional ethics, are probably inimical to greater distributional equity within and among nations, enhance vulnerability and the paramilitarization of civilian life, introduce major economic and social risks, and reinforce current trends toward centrifugal politics. Deployment of fission technology produces further social and ethical problems, since attempts to reduce potential hazards from operating accidents, from escape of nuclear wastes, or from nuclear violence and coercion will have socio-political side-effects even if they succeed, not to mention the side-effects if they fail. These side-effects, many of which would be worse with fast than with thermal reactors, include repressiveness, abrogation of civil liberties, social rigidity and homogeneity, elitist technocracy, dirigiste autarchy, and suppression of ethical objections. The inability of modern political institutions to cope with the persistent hazards of toxic and explosive nuclear materials strains the competence and perceived legitimacy of those institutions as they try to compromise between individual liberties and public safety and to subject to democratic decision technically tinged policy questions that turn largely on unknown or unknowable information. There is no scientific basis for calculating the likelihood on the maximum long-term of nuclear mishaps, nor for guaranteeing that the effects will not exceed a particular level; it is only known that all precautions are, for fundamental reasons

  16. Three core concepts for producing uranium-233 in commercial pressurized light water reactors for possible use in water-cooled breeder reactors

    International Nuclear Information System (INIS)

    Selected prebreeder core concepts are described which could be backfit into a reference light water reactor similar to current commercial reactors, and produce uranium-233 for use in water-cooled breeder reactors. The prebreeder concepts were selected on the basis of minimizing fuel system development and reactor changes required to permit a backfit. The fuel assemblies for the prebreeder core concepts discussed would occupy the same space envelope as those in the reference core but contain a 19 by 19 array of fuel rods instead of the reference 17 by 17 array. An instrument well and 28 guide tubes for control rods have been allocated to each prebreeder fuel assembly in a pattern similar to that for the reference fuel assemblies. Backfit of these prebreeder concepts into the reference reactor would require changes only to the upper core support structure while providing flexibility for alternatives in the type of fuel used

  17. Level-2 PSA for the prototype fast breeder reactor MONJU applied to the accident management review

    International Nuclear Information System (INIS)

    An accident management guideline (AMG) of the prototype fast breeder reactor MONJU has been presented to Nuclear and Industry Safety Agency (NISA) of METI by Japan Atomic Energy Agency (JAEA) with an evaluation result of an effectiveness of the AMG by employing Level-1 and Level-2 PSAs. Japan Nuclear Energy Safety Organization (JNES) evaluated the three events - PLOHS, LORL and ATWS events - and scrutinized the results of the Level-2 PSA carried out by JAEA from the view point of an accident management (AM) review. Regarding ATWS events, we have carried out a qualitative evaluation of the results of JAEA's evaluation and carried out a quantitative evaluation of the containment failure frequency (CFF) in relation to Protected-Loss-of-Heat-Sink (PLOHS) and Loss-of-Reactor-Level (LORL) events. Evaluation of the containment failure probability CFF has been conducted based on the results of the Level-1 PSA by employing the code system developed by JNES. We conducted a close examination of the procedure that JAEA followed to evaluate CFFs in PLOHS and LORL events. It was confirmed that JAEA's Level-2 PSA quantified the phenomenal event trees was expanded in the three processes - the plant response process, the core damage process and the containment vessel response process - based on various analytical and experimental evidence and otherwise followed much the same basic evaluation procedures employed by JNES. As for PLOHS and LORL, quantitative evaluation of CFF was conducted according to the following procedures: Development of an event flow diagram, Development of a phenomenal event tree, Quantification of the phenomenal event tree, Evaluation of containment failure frequencies, and Evaluation of the effectiveness of the AM measures. In the evaluation of the PLOHS and LORL events, the following analytical codes were used; Plant dynamic characteristic analytical code (NALAP-II), Nuclear characteristics analytical system (ARCADIAN-FBR/MVP), Nuclear dynamics analysis code

  18. Reactor Vessel Surveillance Program for Advanced Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Kyeong-Hoon; Kim, Tae-Wan; Lee, Gyu-Mahn; Kim, Jong-Wook; Park, Keun-Bae; Kim, Keung-Koo

    2008-10-15

    This report provides the design requirements of an integral type reactor vessel surveillance program for an integral type reactor in accordance with the requirements of Korean MEST (Ministry of Education, Science and Technology Development) Notice 2008-18. This report covers the requirements for the design of surveillance capsule assemblies including their test specimens, test block materials, handling tools, and monitors of the surveillance capsule neutron fluence and temperature. In addition, this report provides design requirements for the program for irradiation surveillance of reactor vessel materials, a layout of specimens and monitors in the surveillance capsule, procedures of installation and retrieval of the surveillance capsule assemblies, and the layout of the surveillance capsule assemblies in the reactor.

  19. Development of standards and investigation of safety examination items for advancement of safety regulation of fast breeder reactor

    International Nuclear Information System (INIS)

    The purposes of this study are to prepare the fuel technical standard and the structure and materials standard of fast breeder reactors (FBRs), and to develop the requirements in a reactor establishment permission. The objects of this study are mainly the Monju high performance core and a demonstration FBR. In JFY 2012, the following results were obtained. As for the fuel technical standard, the fuel technical standard adapting the examination of integrity of the FBR fuels was prepared based on the information and data obtained in this study. As for the structure and material standard, the investigation of the revised parts of the standard was carried out. And as for the examination of the safety requirements, safety evaluation items for the future FBR plant and the fission products to be considered in a reactor establishment permission were investigated and examined. (author)

  20. Gas-cooled fast breeder reactor. Quarterly progress report, February 1-April 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1980-05-01

    Information is presented concerning the reactor vessel; reactivity control mechanisms and instrumentation; reactor internals; primary coolant circuits;core auxiliary cooling system; reactor core; systems engineering; and reactor safety and reliability;

  1. Internal welding of tube-to-tubesheet joints of steam generator for sodium-cooled fast breeder reactor

    International Nuclear Information System (INIS)

    In the steam generator for a sodium-cooled fast breeder reactor, there are many joints of tubes and tube sheets. For the internal welding of small diameter, thick walled tubes and tubesheets, welding method has been developed, which gives high quality welding with good reproducibility. In this method, the pressure of shield gas is controlled suitably, and consideration is given to the composition of the shield gas. As a means to ensure the quality of welds, the technique of internal radiographic test has also been established. Both the welding method and the test were able to be applied successfully to the steam generator of practical size. (Mori, K.)

  2. High-definition radiography of tube-to-tubesheet welds of steam generator of prototype fast breeder reactor

    International Nuclear Information System (INIS)

    In the steam generator of the Prototype Fast Breeder Reactor (PFBR), steam is generated by the transfer of heat from secondary sodium to water. Due to the inherent dangers of sodium-water reaction, the integrity of weld joints separating sodium and water/steam is of paramount importance. This is particularly true and very important for the tube-to-tubesheet joints. This paper discusses the use of projective magnification technique by microfocal radiography for the quality evaluation and optimisation of the welding parameters of such small tube-to-tubesheet welds of the steam generator of PFBR. (author)

  3. Dynamic simulation of the air-cooled decay heat removal system of the German KNK-II experimental breeder reactor

    International Nuclear Information System (INIS)

    A Dump Heat Exchanger and associated feedback control system models for decay heat removal in the German KNK-II experimental fast breeder reactor are presented. The purpose of the controller is to minimize temperature variations in the circuits and, hence, to prevent thermal shocks in the structures. The basic models for the DHX include the sodium-air thermodynamics and hydraulics, as well as a control system. Valve control models for the primary and intermediate sodium flow regulation during post shutdown conditions are also presented. These models have been interfaced with the SSC-L code. Typical results of sample transients are discussed

  4. MINT research reactor safety program

    Energy Technology Data Exchange (ETDEWEB)

    Mohamad Idris bin Taib [Division of Special Project, Malaysian Institute for Nuclear Technology Research (MINT), Bangi (Malaysia)

    2000-11-01

    Malaysian Institute for Nuclear Technology Research (MINT) Research Reactor Safety Program has been done along with Reactor Power Upgrading Project, Reactor Safety Upgrading Project and Development of Expert System for On-Line Nuclear Process Control Project. From 1993 up to date, Neutronic and Thermal-hydraulics analysis, Probabilistic Safety Assessment as well as installation of New 2 MW Secondary Cooling System were done. Installations of New Reactor Building Ventilation System, Reactor Monitoring System, Updating of Safety Analysis Report and Upgrading Primary Cooling System are in progress. For future activities, Reactor Modeling will be included to add present activities. (author)

  5. EPRI Asilomar papers: on the possibility of advanced fuel fusion reactors, fusion-fission hybrid breeders, small fusion power reactors, Asilomar, California, December 15--17, 1976

    International Nuclear Information System (INIS)

    An EPRI Ad Hoc Panel met in Asilomar, California for a three day general discussion of topics of particular interest to utility representatives. The three main topics considered were: (1) the possibility of advanced fuel fusion reactors, (2) fusion-fission hybrid breeders, and (3) small fusion power reactors. The report describes the ideas that evolved on these three topics. An example of a ''neutron less'' fusion reactor using the p-11B fuel cycle is described along with the critical questions that need to be addressed. The importance to the utility industry of using fusion neutrons to breed fission fuel for LWRs is outlined and directions for future EPRI research on fusion-fission systems are recommended. The desirability of small fusion power reactors to enable the early commercialization of fusion and for satisfying users' needs is discussed. Areas for possible EPRI research to help achieve this goal are presented

  6. The use of a genetic-counselling program by Dutch breeders for four hereditary health problems in boxer dogs.

    Science.gov (United States)

    van Hagen, Marjan A E; Janss, Luc L G; van den Broek, Jan; Knol, Bart W

    2004-04-30

    Our group developed a genetic-counselling program for boxer-dog breeders in The Netherlands, using data for cryptorchidism (uni- and/or bilateral), epilepsy, knee-problems (including ligament rupture, fractured or ruptured meniscus, severe osteo-arthrosis of the knee, or a combination of these disorders), and schisis (including cheiloschisis, palatoschisis, or cheilopalatoschisis). We transformed the estimated breeding values (EBVs) into odds ratios (ORs), to enable the breeder to compare the risk for each of the traits for a certain dam-sire combination with the average population risk (set at 1). The goal of the study was to evaluate the use of our genetic-counselling program by Dutch breeders of boxer dogs. We asked breeders of the Dutch Boxer Club to send in an application form for genetic-counselling from June 1 to December 1, 2000. Breeders indicated on this application form three desirable sires for their dam (sire 1, sire 2, sire 3) in random order. On the basis of this information, a counselling report was produced which included ORs for the four diseases in litters of the dam-sire combinations indicated on the application form. Together with the counselling report, the breeders received an evaluation form. We received 129 application forms from 70 breeders, and collected 125 evaluations. Of these evaluations, 96 were informative about the influence of the counselling report on sire choice. The most-important criteria used by breeders to select sires were: the exterior characteristics (60%) and known progeny (52%). Although it was the first time breeders could make use of genetic-counselling, 32% of the breeders indicated that the genetic-counselling played a major role in their sire selection. Breeders expressed little difference in importance for the four genetic traits, but there was a tendency to consider epilepsy more than the others. Breeders hesitated to put long-term population interest above short-term personal interest. Nevertheless, the general

  7. Advanced Fission Reactor Program objectives

    International Nuclear Information System (INIS)

    The objective of an advanced fission reactor program should be to develop an economically attractive, safe, proliferation-resistant fission reactor. To achieve this objective, an aggressive and broad-based research and development program is needed. Preliminary work at Brookhaven National Laboratory shows that a reasonable goal for a research program would be a reactor combining as many as possible of the following features: (1) initial loading of uranium enriched to less than 15% uranium 235, (2) no handling of fuel for the full 30-year nominal core life, (3) inherent safety ensured by core physics, and (4) utilization of natural uranium at least 5 times as efficiently as light water reactors

  8. Status of National Programmes on Fast Breeder Reactors. International Working Group on Fast Reactors, Twentieth Annual Meeting, Vienna, 24-27 March 1987

    International Nuclear Information System (INIS)

    The Agenda of the meeting was as follows: 1. Approval of the Agenda. 2. Approval of the minutes of the 19th meeting of the IWGFR. 3. Report of the Scientific Secretary regarding the WD activities of the Working Group. 4. Presentations and discussions on national programmes on fast breeder reactors. 5. Consideration of conferences on fast breeder reactors. a. ANS-ENS International Conference on Fast Breeder Systems Experience Gained and Path to Economical Power Generation, Richland, Washington, USA, 13-17 September 1987. b. International Conference on Liquid Metal Engineering and Technology, Avignon, France, 17-20 October 1988. c. Other meetings of interest to IWGFR members. 6. Consideration of major recommendations of some of the WD IWGFR Specialists' Meetings. 7. Consideration of arrangements for Specialists' Meetings in 1987. a. Specialists' Meeting on Fission and Corrosion Products Behaviour in Primary Circuits of LMFBRs, Karlsruhe, Fed. Rep. of Germany, May 1987. b. Specialists' Meeting on LMFBR Reactor Block Antiseismic Design and Verification, Bologna, Italy, October 1987. 8. Selection of topics for Specialists' Meetings to be held in 1988 and suggestions of the IWGFR on other Specialists' Meetings and their justifications. 9. Consideration of joint research activities: a. Coordinated Research Programme on a Comparative Assessment of Processing Techniques for Analysis of Sodium Boiling Noise Detection Data. b. Coordinated Research Programme on Intercomparison of LMFBR Core Mechanics Codes. c. New Topics of CRP. d. Other Activities. 10. Updating of ''LMFBR Plant Parameters''. 11. Informal discussion on ''Safety Criteria for Fast Reactors in IWGFR Countries''. 12. The date and place of the 21th Annual Meeting of the IWGFR

  9. U.S. reference paper on national decisions on breeder development and deployment

    International Nuclear Information System (INIS)

    Factors involved in making national decisions on the deployment of breeder reactor systems are identified in terms of a nation's potential for electrification, capital resources, the available industrial and manpower infrastructure and importance attached to energy independence and the degree to which a breeder program can help realize this objective in the time scale of interest. The specific factors analysed are: the high capital cost of the breeder and the one-time transition costs to bring the breeder to maturity the high breeder research, development and demonstration costs, the impact of discount rate, and the fuel cycle costs, e.g. indigeneous facilities or purchase of services. A principal conclusion of this paper is that nations may find it more economical to continue to deploy LWRs for a number of years rather than to consider the breeder option because of the initial high breeder capital cost and high breeder R and D costs

  10. Investigation of stability of multi free surfaces at transient operation for fast breeder demonstration reactors in Japan

    International Nuclear Information System (INIS)

    The Japanese demonstration fast breeder reactor (JDFBR) is composed of a reactor vessel, intermediate heat exchangers and pump vessels. Every component has a free surface of sodium. Transient operation of the pumps may cause variations of the sodium levels. For the stability of the multiple surfaces, a 1/15 scale model of the JDFBR with 4 loops with a 1000 MWe output power was made to experimentally investigate the stability of 9 free surfaces. In addition, we have developed a computer code to calculate it. The results of the experiments and the calculations agree well with each other. The computer code was successfully verified. The cover gas has an important role to suppress the vibrations of the free surfaces in transient conditions. The sodium level of the JDFBR is stable in all operating conditions, even beyond the design base conditions. (author)

  11. Markovian reliability analysis under uncertainty with an application on the shutdown system of the Clinch River Breeder Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Papazoglou, I A; Gyftopoulos, E P

    1978-09-01

    A methodology for the assessment of the uncertainties about the reliability of nuclear reactor systems described by Markov models is developed, and the uncertainties about the probability of loss of coolable core geometry (LCG) of the Clinch River Breeder Reactor (CRBR) due to shutdown system failures, are assessed. Uncertainties are expressed by assuming the failure rates, the repair rates and all other input variables of reliability analysis as random variables, distributed according to known probability density functions (pdf). The pdf of the reliability is then calculated by the moment matching technique. Two methods have been employed for the determination of the moments of the reliability: the Monte Carlo simulation; and the Taylor-series expansion. These methods are adopted to Markovian problems and compared for accuracy and efficiency.

  12. Level monitoring system with pulsating sensor—Application to online level monitoring of dashpots in a fast breeder reactor

    Science.gov (United States)

    Malathi, N.; Sahoo, P.; Ananthanarayanan, R.; Murali, N.

    2015-02-01

    An innovative continuous type liquid level monitoring system constructed by using a new class of sensor, viz., pulsating sensor, is presented. This device is of industrial grade and it is exclusively used for level monitoring of any non conducting liquid. This instrument of unique design is suitable for high resolution online monitoring of oil level in dashpots of a sodium-cooled fast breeder reactor. The sensing probe is of capacitance type robust probe consisting of a number of rectangular mirror polished stainless steel (SS-304) plates separated with uniform gaps. The performance of this novel instrument has been thoroughly investigated. The precision, sensitivity, response time, and the lowest detection limit in measurement using this device are Rod Drive Mechanism during reactor operation.

  13. The long-term future for civilian nuclear power generation in France: The case for breeder reactors. Breeder reactors: The physical and physical chemistry parameters, associate material thermodynamics and mechanical engineering: Novelties and issues

    Science.gov (United States)

    Dautray, Robert

    2011-06-01

    The author firstly gives a summary overview of the knowledge base acquired since the first breeder reactors became operational in the 1950s. "Neutronics", thermal phenomena, reactor core cooling, various coolants used and envisioned for this function, fuel fabrication from separated materials, main equipment (pumps, valves, taps, waste cock, safety circuits, heat exchange units, etc.) have now attained maturity, sufficient to implement sodium cooling circuits. Notwithstanding, the use of metallic sodium still raises certain severe questions in terms of safe handling (i.e. inflammability) and other important security considerations. The structural components, both inside the reactor core and outside (i.e. heat exchange devices) are undergoing in-depth research so as to last longer. The fuel cycle, notably the refabrication of fuel elements and fertile elements, the case of transuranic elements, etc., call for studies into radiation induced phenomena, chemistry separation, separate or otherwise treatments for materials that have different radioactive, physical, thermodynamical, chemical and biological properties. The concerns that surround the definitive disposal of certain radioactive wastes could be qualitatively improved with respect to the pressurized water reactors (PWRs) in service today. Lastly, the author notes that breeder reactors eliminate the need for an isotope separation facility, and this constitutes a significant contribution to contain nuclear proliferation. Among the priorities for a fully operational system (power station - the fuel cycle - operation-maintenance - the spent fuel pool and its cooling system-emergency cooling system-emergency electric power-transportation movements-equipment handling - final disposal of radioactive matter, independent safety barriers), the author includes materials (fabrication of targets, an irradiation and inspection instrument), the chemistry of all sorting processes, equipment "refabrication" or rehabilitation

  14. Status of national programmes on fast breeder reactors. Twenty-fifth annual meeting of the International Working Group on Fast Reactors. Summary report. Working material

    International Nuclear Information System (INIS)

    At present nuclear power accounts for approximately 17% of total electricity generation worldwide. Given continuing population growth and the needs of the third world and developing countries to improve their economic performance and standard of living, energy demand is expected to continue to grow through the 21st century. The proportion of energy supplied as electricity is also expected to continue to increase. Although fossil fuelled electricity generation is the option preferred by several countries for the short term, there are rising concerns over climatic consequences caused by extended burning of fossil fuels as a result of the demands of a fast expanding world population. In this situation nuclear electricity will become more and more important and the known reserves of uranium would be consumed quite quickly by thermal reactors. It would be possible to sustain a large nuclear programme only by introducing fast reactors. One can conclude that there are strategic reasons for pursuing the development of fast breeder reactors. It will become desirable essential, to have this technology available for introduction. The experience of the various prototypes presently in operation has confirmed the operability and benign characteristics of the LMFR and has given ground for confidence in the future. Current fast reactor designs offer very large margins of safety and by virtue of redundant and diverse safety systems the potential for an energetic core disruptive accident or for fast reactor core meltdown has been essentially eliminated. Several international forums reviewed the current trends in the fast reactor development. The view was reaffirmed that fast breeder reactors still remain the most practical tool for effective utilization of uranium resources for the future energy needs. Achievement of competitiveness with LMRs is still the first priority condition for the future deployment of this type of reactor. The recycling of plutonium into LMFBRs would allow

  15. Gas-cooled fast reactor program. Progress report, January 1, 1980-June 30, 1981

    International Nuclear Information System (INIS)

    Since the national Gas-Cooled Fast Breeder Reactor Program has been terminated, this document is the last progress report until reinstatement. It is divided into three sections: Core Flow Test Loop, GCFR shielding and physics, and GCFR pressure vessel and closure studies

  16. Gas-cooled fast reactor program. Progress report, January 1, 1980-June 30, 1981

    Energy Technology Data Exchange (ETDEWEB)

    Kasten, P.R.

    1981-09-01

    Since the national Gas-Cooled Fast Breeder Reactor Program has been terminated, this document is the last progress report until reinstatement. It is divided into three sections: Core Flow Test Loop, GCFR shielding and physics, and GCFR pressure vessel and closure studies. (DLC)

  17. Modeling and analysis of the unprotected loss-of-flow accident in the Clinch River Breeder Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Morris, E.E.; Dunn, F.E.; Simms, R.; Gruber, E.E.

    1985-01-01

    The influence of fission-gas-driven fuel compaction on the energetics resulting from a loss-of-flow accident was estimated with the aid of the SAS3D accident analysis code. The analysis was carried out as part of the Clinch River Breeder Reactor licensing process. The TREAT tests L6, L7, and R8 were analyzed to assist in the modeling of fuel motion and the effects of plenum fission-gas release on coolant and clad dynamics. Special, conservative modeling was introduced to evaluate the effect of fission-gas pressure on the motion of the upper fuel pin segment following disruption. For the nominal sodium-void worth, fission-gas-driven fuel compaction did not adversely affect the outcome of the transient. When uncertainties in the sodium-void worth were considered, however, it was found that if fuel compaction occurs, loss-of-flow driven transient overpower phenomenology could not be precluded.

  18. Carbon transport in a bimetallic sodium loop simulating the intermediate heat transport system of a liquid metal fast breeder reactor

    International Nuclear Information System (INIS)

    Carbon transport data from a bimetallic sodium loop simulating the intermediate heat transport system of a Liquid Metal Fast Breeder Reactor are discussed. The results of bulk carbon analyses after 15,000 hours' exposure indicate a pattern of carburization of Type 304 stainless steel foils which is independent of loop sodium temperature. A model based on carbon activity gradients accounting for this behavior is proposed. Data also indicate that carburization of Type 304 stainless steel is a diffusion-controlled process; however, decarburization of the ferritic 2 1/4 Cr-1Mo steel is not. It is proposed that the decarburization of the ferritic steel is controlled by the dissolution of carbides in the steel matrix. The differences in the sodium decarburization behavior of electroslag remelted and vacuum-arc remelted 2 1/4 Cr-1Mo steel are also highlighted

  19. Fission energy program of the US Department of Energy, FY 1981

    Energy Technology Data Exchange (ETDEWEB)

    Ferguson, Robert L.

    1980-03-01

    Information is presented concerning the National Energy Plan and fission energy policy; fission energy program management; converter reactor systems; breeder reactor systems; and special nuclear evaluations and systems.

  20. Fission energy program of the US Department of Energy, FY 1981

    International Nuclear Information System (INIS)

    Information is presented concerning the National Energy Plan and fission energy policy; fission energy program management; converter reactor systems; breeder reactor systems; and special nuclear evaluations and systems

  1. Multiple recycling of fuel in prototype fast breeder reactor in a closed fuel cycle with pressurized heavy-water reactor external feed

    Indian Academy of Sciences (India)

    G Pandikumar; A John Arul; P Puthiyavinayagam; P Chellapandi

    2015-10-01

    A fast breeder reactor (FBR) closed fuel cycle involves recycling of the discharged fuel, after reprocessing and refabrication, in order to utilize the unburnt fuel and the bred fissile material. Our previous study in this regard for the prototype fast breeder reactor (PFBR) indicated the possibility of multiple recycling with self-sufficiency. It was found that the change in Pu composition becomes negligible (less than 1%) after a few cycles. The core-1 Pu increases by 3% from the beginning of cycle-0 to that of recycle-1, the Pu increase from the beginning of the 9th cycle to that of the 10th by only 0.3%. In this work, the possibility of multiple recycling of PFBR fuel with external plutonium feed from pressurized heavy-water reactor (PHWR) is examined. Modified in-core cooling and reprocessing periods are considered. The impact of multiple recycling on PFBR core physics parameters due to the changes in the fuel composition has been brought out. Instead of separate recovery considered for the core and axial blankets in the earlier studies, combined fuel recovery is considered in this study. With these modifications and also with PHWR Pu as external feed, the study on PFBR fuel recycling is repeated. It is observed that the core-1 initial Pu inventory increases by 3.5% from cycle-0 to that of recycle-1, the Pu increase from the beginning of the 9th cycle to that of the 10th is only 0.35%. A comparison of the studies done with different external plutonium options viz., PHWR and PFBR radial blanket has also been made.

  2. The passive nondestructive assay of the plutonium content of spent-fuel assemblies from the BN-350 fast-breeder reactor in the city of Aqtau, Kazakhstan

    CERN Document Server

    Lestone, J P; Rennie, J A; Sprinkle, J K; Staples, P; Grimm, K N; Hill, R N; Cherradi, I; Islam, N; Koulikov, J; Starovich, Z

    2002-01-01

    The International Atomic Energy Agency is presently interested in developing equipment and techniques to measure the plutonium content of breeder reactor spent-fuel assemblies located in storage ponds before they are relocated to more secure facilities. We present the first quantitative nondestructive assay of the plutonium content of fast-breeder reactor spent-fuel assemblies while still underwater in their facility storage pond. We have calibrated and installed an underwater neutron coincidence counter (Spent Fuel Coincidence Counter (SFCC)) in the BN-350 reactor spent-fuel pond in Aqtau, Kazakhstan. A procedure has been developed to convert singles and doubles (coincidence) neutron rates observed by the SFCC into the total plutonium content of a given BN-350 spent-fuel assembly. The plutonium content has been successfully determined for spent-fuel assemblies with a contact radiation level as high as approx 10 sup 5 Rads/h. Using limited facility information and multiple measurements along the length of spe...

  3. Effects of breeder feeding restriction programs and incubation temperatures on progeny footpad development.

    Science.gov (United States)

    Da Costa, M J; Oviedo-Rondón, E O; Wineland, M J; Wilson, J; Montiel, E

    2014-08-01

    Footpad dermatitis begins early in life, and there is evidence of individual susceptibility. An experiment was conducted to evaluate the carryover effects of breeder feed restriction programs and incubation temperatures (TEM) on progeny footpad development at hatch, and 7 and 22 d. Cobb 500 fast feathering breeders were subjected to 2 dietary feed restriction programs during rearing: skip-a-day (SAD) and every-day feeding (EDF). At 60 wk of age, eggs from each group were collected and incubated according to 2 TEM, standard (S) eggshell temperature (38.1°C) and early-low late-high (LH). This second profile had low (36.9°C) eggshell temperature for the first 3 d, and standard temperature until the last 3 d when eggs were subjected to elevated (38.9°C) eggshell temperature. At hatch, 15 chicks from each treatment combination were sampled to obtain footpads for histological analysis. Seventy-two chicks per treatment were placed in 48 cages (6/cage), and raised to 22 d. At 7 and 22 d, 1 and 2 chickens, respectively, were sampled for footpads. The BW and group feed intake were recorded to obtain BW gain and feed conversion ratio at 7 and 21 d. Histological analysis assessed thickness and total area of stratus corneum (SC), epidermis, and dermis, and total papillae height. Data were analyzed as randomized complete block design in a 2 × 2 factorial arrangement of treatments. There was a negative effect of LH TEM on performance at both ages. An interaction effect on SC area and papillae height was observed at hatch. Additionally, SAD treatment increased thickness and area of footpad dermis. At 7 d, the SC parameters of the SAD progeny were increased. Epidermis thickness was affected by treatment interaction. Furthermore, LH TEM decreased epidermis thickness and dermis area. At 22 d, interaction effects were observed in thickness and area of SC and epidermis. Incubation S TEM increased thickness and area of dermis. It was concluded that breeder feed restriction programs

  4. Numerical analysis of grid plate melting after a severe accident in a Fast-Breeder Reactor (FBR)

    Indian Academy of Sciences (India)

    A Jasmin Sudha; K Velusamy

    2013-12-01

    Fast breeder reactors (FBRs) are provided with redundant and diverse plant protection systems with a very low failure probability (<10-6/reactor year), making core disruptive accident (CDA), a beyond design basis event (BDBE). Nevertheless, safety analysis is carried out even for such events with a view to mitigate their consequences by providing engineered safeguards like the in-vessel core catcher. During a CDA, a significant fraction of the hot molten fuel moves downwards and gets relocated to the lower plate of grid plate. The ability of this plate to resist or delay relocation of core melt further has been investigated by developing appropriate mathematical models and translating them into a computer code HEATRAN-1. The core melt is a time dependent volumetric heat source because of the radioactive decay of the fission products which it contains. The code solves the nonlinear heat conduction equation including phase change. The analysis reveals that if the bottom of grid plate is considered to be adiabatic, melt-through of grid plate (i.e., melting of the entire thickness of the plate) occurs between 800 s and 1000 s depending upon the initial conditions. Knowledge of this time estimate is essential for defining the initial thermal load on the core catcher plate. If heat transfer from the bottom of grid plate to the underlying sodium is taken into account, then melt-through does not take place, but the temperature of grid plate is high enough to cause creep failure.

  5. Conceptual Design Studies of a Passively Safe Thorium Breeder Pebble Bed Reactor

    OpenAIRE

    Wols, F.J.

    2015-01-01

    Nuclear power plants are expected to play an important role in the worldwide electricity production in the coming decades, since they provide an economically attractive, reliable and low-carbon source of electricity with plenty of resources available for at least the coming hundreds of years. However, the design of nuclear reactors can be improved significantly in terms of safety, by designing reactors with fully passive safety systems, and sustainability, by making more efficient use of natu...

  6. European DEMO BOT solid breeder blanket

    International Nuclear Information System (INIS)

    The BOT (Breeder Outside Tube) Solid Breeder Blanket for a fusion DEMO reactor is presented. This is one of the four blanket concepts under development in the frame of the European fusion technology program with the aim to select in 1995 the two most promising ones for further development. In the paper the reference blanket design and external loops are described as well as the results of the theoretical and experimental work in the fields of neutronics, thermohydraulics, mechanical stresses, tritium control and extraction, development and irradiation of the ceramic breeder material, beryllium development, ferromagnetic forces caused by disruptions, safety and reliability. An outlook is given on the remaining open questions and on the required R and D program. (orig.)

  7. New Production Reactors Program Plan

    International Nuclear Information System (INIS)

    Part I of this New Production Reactors (NPR) Program Plan: describes the policy basis of the NPR Program; describes the mission and objectives of the NPR Program; identifies the requirements that must be met in order to achieve the mission and objectives; and describes and assesses the technology and siting options that were considered, the Program's preferred strategy, and its rationale. The implementation strategy for the New Production Reactors Program has three functions: Linking the design, construction, operation, and maintenance of facilities to policies requirements, and the process for selecting options. The development of an implementation strategy ensures that activities and procedures are consistent with the rationale and analysis underlying the Program. Organization of the Program. The strategy establishes plans, organizational structure, procedures, a budget, and a schedule for carrying out the Program. By doing so, the strategy ensures the clear assignment of responsibility and accountability. Management and monitoring of the Program. Finally, the strategy provides a basis for monitoring the Program so that technological, cost, and scheduling issues can be addressed when they arise as the Program proceeds. Like the rest of the Program Plan, the Implementation Strategy is a living document and will be periodically revised to reflect both progress made in the Program and adjustments in plans and policies as they are made. 21 figs., 5 tabs

  8. The use of a genetic-counselling program by Dutch breeders for four hereditary health problems in boxer dogs

    NARCIS (Netherlands)

    Hagen, van M.A.E.; Janss, L.L.G.; Broeck, van den J.; Knol, B.W.

    2004-01-01

    Our group developed a genetic-counselling program for boxer-dog breeders in The Netherlands, using data for cryptorchidism (uni- and/or bilateral), epilepsy, knee-problems (including ligament rupture, fractured or ruptured meniscus, severe osteo-arthrosis of the knee, or a combination of these disor

  9. The Role of Energetic Mixed-Oxide-Fuel-Sodium Thermal Interactions in Liquid Metal Fast Breeder Reactor Safety

    International Nuclear Information System (INIS)

    Recent efforts dealing with the consequence assessment of low-probability core-disruptive accidents (CDAs) in liquid-metal fast breeder reactors (LMFBRs) suggest that unrealistic physical processes must be postulated in order to achieve energetic prompt burst conditions leading to a true hydrodynamic disassembly of the reactor core. Such calculations are, however, being used in the licensing process in order to provide an estimate of safety margins provided by a given design. Figure 1 illustrates calculations for the Fast Flux Test Facility (FFTF) and the Clinch River Breeder Reactor (CRBR), where the prompt critical excursion and associated ramp rates are induced by postulating various amounts and rates of collapsing fuel in a largely molten core (recriticality accident), and the mode of energy release considered is the expansion of fuel vapor resulting in sodium-slug impact on the reactor vessel head. The VENUS-II code is used to calculate the disassembly motion and power histories during disassembly Elementary thermodynamic calculations provide the source term based upon expansion of the fuel from an initial temperature distribution specified by VENUS calculations, and the REXCO series of codes provide a hydrodynamic calculation of the pressure propagation coupled with an analysis of the structural response of the important system components. The work potential resulting from fuel collapse and hydrodynamic disassembly is very sensitive to small variations in the ramp rate. Since material motions associated with postulated conditions leading to energetic prompt critical excursions cannot be described with sufficient accuracy to provide reasonable bounds on ramp rates, an adequate margin of safety with current design is difficult to claim if these conditions cannot be ruled out. This implies that in addition to coherent gravity collapse, the possibility of pressure-driven (fuel-coolant interaction) collapse must be considered. Furthermore, the work potential

  10. A knowledge based on-line diagnostic system for the fast breeder reactor KNKII

    International Nuclear Information System (INIS)

    In the nuclear research center at Karlsruhe, a diagnostic expert system is developed to supervise a fast breeder process (KNKII). The problem is to detect critical phases in the beginning state before fault propagation. The expert system itself is integrated in a computer network (realized by a local area network), where different computers are involved as special detection systems (for example acoustic noise, temperature noise, covergas monitoring and so on), which produce partial diagnoses, based on intelligent signal processing techniques like pattern recognition. Additional to the detection systems a process computer is integrated as well as a test computer, which simulates hypothetical and real fault data. On the logical top level the expert system manages the partial diagnoses of the detection systems with the operating data of the process computer and to produce a final diagnosis including the explanation part for operator support. The knowledge base is developed by typical Artificial Intelligence tools. Both fact based and rule based knowledge representations are stored in form of flavors and predications. The inference engine operates on a rule based approach. Specific detail knowledge, based on experience about any years, is available to influence the decision process by increasing or decreasing of the generated hypotheses. In a meta knowledge base, a rule master triggers the special domain experts and contributes the tasks to the specific rule complexes. Such a system management guarantees a problem solving strategy, which operates event triggered and situation specific in a local inference domain. (author). 3 refs, 6 figs, 2 tabs

  11. Investigations on the mechanical interaction between fuel and cladding (FCMI) in fast breeder reactor fuel pins

    International Nuclear Information System (INIS)

    The relation between FCMI and plastic cladding distensions of Fast-Breeder pins with oxide as well as carbide fuel was analyzed theoretically and experimentally. This resulted in the possibility of plastic cladding straining caused by differential swelling of fuel and cladding material under stationary power conditions or differential thermal expansion at power changes. At stationary operating conditions the FCMI in oxide pins is limited by an irradiation-induced creep deformation into inner void volume and thus the fuel swelling pressure will never cause clad distensions worth mentioning. However, the cladding of carbide pins can be strained under stationary conditions because of the comparatively low fuel plastification under irradiation. Plastic straining of oxide pins may follow from differential thermal expansion at power changes. The amount of strain is primarily dependent upon magnitude and rate of the power increase, the starting conditions, and the clad material strength. The parameter dependence of the strains and the limiting conditions for their avoidance are reported. The model calculations are carried out by means of a special computer code which was developed following closely the results of irradiation experiments. It was proved experimentally that a considerably high geometrical swelling occurs after a power reduction until the fuel has come into contact with the cladding again. (orig.)

  12. Compatibility of structural materials with fusion reactor coolant and breeder fluids

    International Nuclear Information System (INIS)

    Fusion reactors are characterized by a lithium-containing blanket, a heat transfer medium that is integral with the blanket and first wall, and a heat engine that couples to the heat transfer medium. A variety of lithium-containing substances have been identified as potential blanket materials, including molten lithium metal, molten LiF--BeF2, Pb--Li alloys, and solid ceramic compounds such as Li2O. Potential heat transfer media include liquid lithium, liquid sodium, molten nitrates, water, and helium. Each of these coolants and blankets requires a particular set of chemical and mechanical properties with respect to the associated reactor and heat engine structural materials. This paper discusses the materials factors that underlie the selection of workable combinations of blankets and coolants. It also addresses the materials compatibility problems generic to those blanket-coolant combinations currently being considered in reactor design studies

  13. Level-2 PSA for the Prototype Fast Breeder Reactor MONJU Applied to the Accident Management Review

    International Nuclear Information System (INIS)

    JNES independently evaluated the three events it selected - PLOHS, LORL and ATWS events - and reviewed the results of the Level 2 PSA carried out by JAEA. Regarding ATWS events, the organization carried out a qualitative evaluation of the results of JAEA's evaluation and carried out a quantitative evaluation of the containment failure frequency (CFF) in relation to PLOHS and LORL events. In JNES's independent evaluation of PLOHS and LORL events, accident scenarios in the three phases - the plant response phase, the core damage phase and the containment vessel response phase - were analyzed. The phenomenal event trees were quantified by applying the information about phenomena specific to fast reactors, including plant thermal-hydraulic analysis at the time of core damage, boundary structure analysis, analysis of the characteristics of the disrupted core, the results of sodium-concrete reaction tests, and the results of hydrogen diffusion induced combustion tests, to the PRDs. As the result, the total CFF before the preparation of the AM measures was rated at 9.2E-9/reactor year (CDF at 2.7E-7/reactor year), and it has been confirmed that these numerical values are well below the power reactor performance goal indicator values (CDF: 10-4/year or so; CFF: 10-5/year or so) even before the preparation of the AM measures. (author)

  14. Uncertainty evaluation of reliability of safety grade decay heat removal system of Indian prototype fast breeder reactor

    International Nuclear Information System (INIS)

    Highlights: • Uncertainty analysis of failure frequency of SGDHRS of a medium sized fast reactor is studied. • Lognormal distribution of failure rate of components is taken with error factor of 3. • The error factor in the distribution of failure frequency in most cases is 3. • The relative importance of the safety components is brought out. - Abstract: Deterministic and probabilistic safety assessment of nuclear power reactor technology is very important in assuring that the design is robust and safety systems perform as per requirement. The parameters required as input data for such analysis have uncertainties associated with them. Their impact is to be assessed on the results obtained for such analyses and it affects the overall decision making process. Safety Grade Decay Heat Removal System (SGDHRS) is one of the safety systems in fast breeder reactors and itremoves decay heat after reactor shutdown. It is a critical safety system; hence failure frequency for SGDHR is targeted to be less than 1.0 × 10−7 per reactor year. By bringing diversity in some of the components of SGDHRS, such as sodium-to-sodium decay heat exchanger (DHX), sodium to air heat exchanger (AHX) and valves, one can achieve the targeted low failure frequency of SGDHRS. We perform uncertainty analysis of the reliability of such SGDHRS here. Uncertainty in failure rate (of components of SGDHRS) is assumed to follow the log-normal distribution with error factor of three. Monte Carlo method of sampling is used in MATLAB environment. Results are obtained in terms of mean, median and standard deviation values of failure frequency. Percentile and confidence interval analysis of mean values are also obtained. These provide 95 and 98 percentile and confidence interval values of 98%, 99% and 99.8%. It is found that error factor of failure frequency of SGDHRS is found to be less than 3 in all the cases except the one in which DHX, AHX and Valves are designed with diversity in design. It is to

  15. Linearized model for the hydrodynamic stability investigation of molten fuel jets into the coolant of a Liquid Metal Fast Breeder Reactor (LMFBR)

    Science.gov (United States)

    Hartel, K.

    1986-02-01

    The hydrodynamic stability of liquid jets in a liquid continuum, both characterized by low viscosity was analyzed. A linearized mathematical model was developed. This model enables the length necessary for fragmentation of a vertical, symmetric jet of molten fuel by hydraulic forces in the coolant of a liquid metal fast breeder reactor to be evaluated. On the basis of this model the FRAG code for numerical calculation of the hydrodynamic fragmentation mechanism was developed.

  16. Gas-Cooled Fast Breeder Reactor Preliminary Safety Information Document, Amendment 10. GCFR residual heat removal system criteria, design, and performance

    International Nuclear Information System (INIS)

    This report presents a comprehensive set of safety design bases to support the conceptual design of the gas-cooled fast breeder reactor (GCFR) residual heat removal (RHR) systems. The report is structured to enable the Nuclear Regulatory Commission (NRC) to review and comment in the licensability of these design bases. This report also presents information concerning a specific plant design and its performance as an auxiliary part to assist the NRC in evaluating the safety design bases

  17. Seventeen years of LMFBR experience: Experimental Breeder Reactor II (EBR-II)

    International Nuclear Information System (INIS)

    Operating experience at EBR-II over the past 17 years has shown that a sodium-cooled pool-type reactor can be safely and efficiently operated and maintained. The reactor has performed predictably and benignly during normal operation and during both unplanned and planned plant upsets. The duplex-tube evaporators and superheaters have never experienced a sodium/water leak, and the rest of the steam-generating system has operated without incident. There has been no noticeable degradation of the heat transfer efficiency of the evaporators and superheaters, except for the one superheater replaced in 1981. There has been no need to perform any chemical cleaning of steam-system components

  18. Effect of geometric factors on performance of a sodium to air heat exchanger in a fast breeder reactor

    International Nuclear Information System (INIS)

    Highlights: • A heat exchanger analysis (HE) before scale up reduces excess heat transfer area. • Representative Elementary Volume analysis of a HE speeds up the solution. • The error in air temperature rise prediction by numerical across HE is within 5%. • When both pitches are reduced, the maximum increase in heat flux is experienced. • The experience has resulted in better design of next level heat exchangers. - Abstract: Prototype fast breeder reactor (PFBR) has a safety grade decay heat removal system whose performance depends on the effective functioning of natural convection heat exchangers called sodium to air heat exchangers. The development of Representative Elementary Volume (REV) model for the sodium to air heat exchanger is necessary to envisage its design and to study the effect of various factors for continuous improvement in design. With a Representative Elementary Volume, the hydrodynamic and heat transfer characteristics of the heat exchanger was studied and the results agree well with experimental data. The effect of longitudinal pitch and transverse pitch on the heat exchanger performance has been studied and an improvement of 22% in heat transfer is predicted

  19. TOKOPS: Tokamak Reactor Operations Study: The influence of reactor operations on the design and performance of tokamaks with solid-breeder blankets: Final report

    International Nuclear Information System (INIS)

    Reactor system operation and procedures have a profound impact on the conception and design of power plants. These issues are studied here using a model tokamak system employing a solid-breeder blanket. The model blanket is one which has evolved from the STARFIRE and BCSS studies. The reactor parameters are similar to those characterizing near-term fusion engineering reactors such as INTOR or NET (Next European Tokamak). Plasma startup, burn analysis, and methods for operation at various levels of output power are studied. A critical, and complicating, element is found to be the self-consistent electromagnetic response of the system, including the presence of the blanket and the resulting forces and loadings. Fractional power operation, and the strategy for burn control, is found to vary depending on the scaling law for energy confinement, and an extensive study is reported. Full-power reactor operation is at a neutron wall loading pf 5 MW/m2 and a surface heat flux of 1 MW/m2. The blanket is a pressurized steel module with bare beryllium rods and low-activation HT-9-(9-C-) clad LiAlO2 rods. The helium coolant pressure is 5 MPa, entering the module at 2970C and exiting at 5500C. The system power output is rated at 1000 MW(e). In this report, we present our findings on various operational scenarios and their impact on system design. We first start with the salient aspects of operational physics. Time-dependent analyses of the blanket and balance of plant are then presented. Separate abstracts are included for each chapter

  20. TOKOPS: Tokamak Reactor Operations Study: The influence of reactor operations on the design and performance of tokamaks with solid-breeder blankets: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Conn, R.W.; Ghoniem, N.M.; Firestone, M.A. (eds.)

    1986-09-01

    Reactor system operation and procedures have a profound impact on the conception and design of power plants. These issues are studied here using a model tokamak system employing a solid-breeder blanket. The model blanket is one which has evolved from the STARFIRE and BCSS studies. The reactor parameters are similar to those characterizing near-term fusion engineering reactors such as INTOR or NET (Next European Tokamak). Plasma startup, burn analysis, and methods for operation at various levels of output power are studied. A critical, and complicating, element is found to be the self-consistent electromagnetic response of the system, including the presence of the blanket and the resulting forces and loadings. Fractional power operation, and the strategy for burn control, is found to vary depending on the scaling law for energy confinement, and an extensive study is reported. Full-power reactor operation is at a neutron wall loading pf 5 MW/m/sup 2/ and a surface heat flux of 1 MW/m/sup 2/. The blanket is a pressurized steel module with bare beryllium rods and low-activation HT-9-(9-C-) clad LiAlO/sub 2/ rods. The helium coolant pressure is 5 MPa, entering the module at 297/sup 0/C and exiting at 550/sup 0/C. The system power output is rated at 1000 MW(e). In this report, we present our findings on various operational scenarios and their impact on system design. We first start with the salient aspects of operational physics. Time-dependent analyses of the blanket and balance of plant are then presented. Separate abstracts are included for each chapter.

  1. Model to simulate the fission-product transport process in the Experimental Breeder Reactor II

    Energy Technology Data Exchange (ETDEWEB)

    So, B.Y.C.

    1979-01-01

    When fission products are released from a cladding breach in EBR-II, they mix turbulently with the sodium in the core, in the upper plenum and in the intermediate heat exchanger. Eventually the fission products are discharged 12 to 13 s later into the primary tank. Fission gases migrate upward through a 9-ft layer of sodium and enter the cover gas. Loss of fission gas is due to decay, leakage of cover gas, cold trapping of iodine and bromine parents. Depending on the reactor operation requirement, it may purge with fresh argon. The assumptions made and differential equations used to develop a model for such transport are presented.

  2. Enhanced passive safety features against ATWS of fast breeder reactors with capabilities of MA incineration

    Energy Technology Data Exchange (ETDEWEB)

    Ninokata, Hisashi; Sawada, Tetsuo; Sato, Manabu [Tokyo Institute of Technology (Japan)] [and others

    1997-12-01

    The paper gives an outline of the general and simple reactivity correlation method to identify the region of the major design parameters that assures power stabilization and passive shutdown of sodium-cooled large fast reactors under ATWS conditions. Based on the model developed, general design guidelines are shown that enhance passive capabilities being aimed at preventing sodium boiling and fuel failures in the events of ULOF and UTOP. Discussions extend to the influences of minor actinides loading in the core onto the passive safety features. 6 refs., 1 fig., 1 tab.

  3. Development of safety evaluation methods and analysis codes applied to the safety regulations for the design and construction stage of fast breeder reactor

    International Nuclear Information System (INIS)

    The purposes of this study are to develop the safety evaluation methods and analysis codes needed in the design and construction stage of fast breeder reactor (FBR). In JFY 2012, the following results are obtained. As for the development of safety evaluation methods needed in the safety examination conducted for the reactor establishment permission, development of the analysis codes, such as core damage analysis code, were carried out following the planned schedule. As for the development of the safety evaluation method needed for the risk informed safety regulation, the quantification technique of the event tree using the Continuous Markov chain Monte Carlo method (CMMC method) were studied. (author)

  4. Development of a transfer model for design of sodium purification systems for Fast Breeder Reactors

    International Nuclear Information System (INIS)

    Operating a Sodium Fast Reactor (SFR) in reliable and safe conditions requires to master the quality of the sodium fluid coolant, regarding oxygen and hydrogen impurities contents. A cold trap is a purification unit in SFR, designed for maintaining oxygen and hydrogen contents within acceptable limits. The purification of these impurities is based on crystallization of sodium hydride on cold walls and sodium oxide or hydride on wire mesh packing. Indeed, as oxygen and hydrogen solubilities are nearly nil at temperatures close to the sodium fusion point, i.e. 97.8 C, on line sodium purification can be performed by crystallization of sodium oxide and hydride from liquid sodium flows. However, the management of cold trap performances is necessary to prevent from unforeseen maintenance operations, which could induce shut-down of the reactor. It is thus essential to understand how a cold trap fills up with impurities crystallization in order to optimize the design of this system and to overcome any problems during nominal operation. The objective is to develop a design and simulation tool for cold traps able to predict the location and the amount of the impurities deposited. Crystallization model involve phenomena coupling in a porous medium with hydrodynamics, heat and mass transfer, distinguishing nucleation and growth phases for each impurity. It enables to understand how thermo hydraulic conditions and growing impurities interact on each other. This analysis will adapt operating and management conditions in order to optimize purification requirements. (author)

  5. Significance of coast down time on safety and availability of a pool type fast breeder reactor

    International Nuclear Information System (INIS)

    Highlights: • Plant dynamics studies for quantifying the benefits of flow coast down time. • Establishment of minimum flow coast down time required for safety. • Assessment of influence of flow coast down on enhancing plant availability. • Synthesis of thermo mechanical benefits of flow coast down time on component design. - Abstract: Plant dynamic investigation towards establishing the influence of flow coast down time of primary and secondary sodium systems on safety and availability of plant has been carried out based on one dimensional analysis. From safety considerations, a minimum flow coast down time for primary sodium circuit is essential to be provided to limit the consequences of loss of flow event within allowable limits. Apart from safety benefits, large primary coast down time also improves plant availability by the elimination of reactor SCRAM during short term power failure events. Threshold values of SCRAM parameters also need optimization. By suitably selecting the threshold values for SCRAM parameters, significant reduction in the inertia of pumping systems can be derived to obtain desirable results on plant availability. With the optimization of threshold values and primary flow coast down behaviour equivalent to a halving time of 8 s, there is a possibility to eliminate reactor SCRAM during short term power failure events extending up to 0.75 s duration. Benefits of secondary flow halving on reducing transient thermal loading on components have also been investigated and mixed effects have been observed

  6. Conceptual design of a uranyl nitrate fueled reactor for the destructive testing of liquid metal fast breeder reactor fuel subassemblies

    International Nuclear Information System (INIS)

    A preliminary design of a uranyl nitrate test reactor is developed, with emphasis placed on the core neutronics and cross section development. ENDF/B-IV cross section data and the AMPX system were used to develop a 25 group neutron cross section library. A series of one-dimensional transport calculations were made in order to arrive at a reference design. Power densities of 16.5 Kw/1 appear to be attainable in the 217 pin FFTF test subassembly, with a peak neutron flux in the test zone of 2.4 x 1014 n/cm2-sec. Other engineering features pertinent to the overall system design are discussed, including: (1) corrosion, (2) treatment of radiolytic gas, (3) heat removal, and (4) reactor control

  7. Power excursion models applied to the study of secundary excursion in sodium cooled fast breeder reactors

    International Nuclear Information System (INIS)

    An evaluation of the energy that a secondary power excursion could release has been sought throughout the present work. A parametric study was therefore made by means of a power excursion code in fast reactors. The work submitted is therefore made up of the three following parts: Part 1. - (a), the secondary excursion is situated in the generally envisaged programmes and (b) the role of the principal parameters is studied in the calculation effected by the nuclear excursion code that was available at the start of the study. Part 2. - the results obtained for the power excursion calculations made are presented, Part 3. - the insufficient modelling of the reactivity present during the secondary power excursion is deduced from the parametric study just made. A definition is made of the characteristics of a model adapted to the calculation of this hypothetical accident and a new model as worked out within the scope of this work is submitted

  8. Utilization of OR method toward realization of better fast breeder reactor cycle

    International Nuclear Information System (INIS)

    Fast Reactor Cycle Technology Development (FaCT) Project was now started aiming at commercialization of new nuclear power plants system. In parallel with development of component technology and technology demonstration by test, development of comprehensive evaluation method of the FBR cycle system is under way and scenario study, discounted cash flow (DCF) method, analytic hierarchy process (AHP), real option, supply chain management (SCM) and others are used. Since commercialized FBR cycle would request long-term and large-scale development contributed by so many participants, modeling of nuclear system and knowledge management are beneficial even for development of evaluation method and further utilization of OR technology is highly expected. Comprehensive evaluation methods now utilized or developing were overlooked from the standpoint of OR, 'Science of Better'. (T. Tanaka)

  9. Studies on gas entrainment due to vortex activation at free surface of fast breeder reactor

    International Nuclear Information System (INIS)

    Fast Reactor systems consist of many cylindrical components which are partially submerged in liquid sodium and partially exposed to argon gas, maintained above the sodium pool. Horizontal sodium flows past these components leads to the formation of von Kármán vortices. These vortices form dimples of argon gas that leads to entrainment. The present work is focused on to identify the criteria for onset of gas entrainment. In order to understand this, interactions between free surface waves and underlying viscous wakes are investigated for flow past a surface piercing cylinder incorporating volume of fluid (VOF) method. The results show that the free surface inhibits the vortex generation near the interface for all range of Froude numbers (FrD). For various inflow velocities, the re-submergence angles are measured. It is found that, for FrD ≤ 0.5, and re-submergence angle < 12°, there is no risk of entrainment due to vortex activation. (author)

  10. Gas cooled fast reactor research and development program

    International Nuclear Information System (INIS)

    The research and development work in the field of core thermal-hydraulics, experimental and analytical physics and carbide fuel development carried out 1978 for the Gas Cooled Fast Breeder Reactor at the Swiss Federal Institute for Reactor Research is described. (Auth.)

  11. Gas cooled fast reactor research and development program

    International Nuclear Information System (INIS)

    The research and development work in the field of core thermal-hydraulics, steam generator research and development, experimental and analytical physics and carbide fuel development carried out 1978 for the Gas Cooled Fast Breeder Reactor at the Swiss Federal Institute for Reactor Research is described. (Auth.)

  12. Thorium utilization in fast breeder reactors and in cross-progeny fuel cycles

    International Nuclear Information System (INIS)

    Thorium fuel cycles have to be closed since the benefit is obtained only when the 233U is used. India is the only country in the world, which has extensive facilities for reprocessing of irradiated Uranium and Thorium-based fuels, thermal reactors moderated by light and heavy water and 500 MWe LMFBRs. The cross-progeny fuel cycles would be a natural vision to pursue for India. This paper was written in 1982 and presented at the U.S. Japan Seminar on Thorium fuel cycle held in October 1982. The calculations performed and the results quoted in this paper are of that vintage. However, the cross section data for Th and other materials has not changed significantly since that time. The same holds for the methodologies in computer codes, diffusion theory and the other methodologies employed in this paper, versus those in computer codes currently in use. This paper is being submitted to remind the community that with the introduction of GEN IV LMFBRs, other possibilities for thorium utilization could spring forth and should be studied further and in more depth

  13. Engineering development studies for molten-salt breeder reactor processing No. 21

    International Nuclear Information System (INIS)

    The status of the following programs is reported: (1) continuous fluorinator development: autoresistance heating test AHT-4; (2) development of the metal transfer process; (3) salt-metal contactor development: experiments with a mechanically agitated, nondispersing contactor using water and mercury and in the salt-bismuth flowthrough facility; and (4) fuel reconstitution development: installation of equipment for a fuel reconstitution engineering experiment

  14. Materials accounting in a fast-breeder-reactor fuels-reprocessing facility: optimal allocation of measurement uncertainties

    Energy Technology Data Exchange (ETDEWEB)

    Dayem, H.A.; Ostenak, C.A.; Gutmacher, R.G.; Kern, E.A.; Markin, J.T.; Martinez, D.P.; Thomas, C.C. Jr.

    1982-07-01

    This report describes the conceptual design of a materials accounting system for the feed preparation and chemical separations processes of a fast breeder reactor spent-fuel reprocessing facility. For the proposed accounting system, optimization techniques are used to calculate instrument measurement uncertainties that meet four different accounting performance goals while minimizing the total development cost of instrument systems. We identify instruments that require development to meet performance goals and measurement uncertainty components that dominate the materials balance variance. Materials accounting in the feed preparation process is complicated by large in-process inventories and spent-fuel assembly inputs that are difficult to measure. To meet 8 kg of plutonium abrupt and 40 kg of plutonium protracted loss-detection goals, materials accounting in the chemical separations process requires: process tank volume and concentration measurements having a precision less than or equal to 1%; accountability and plutonium sample tank volume measurements having a precision less than or equal to 0.3%, a shortterm correlated error less than or equal to 0.04%, and a long-term correlated error less than or equal to 0.04%; and accountability and plutonium sample tank concentration measurements having a precision less than or equal to 0.4%, a short-term correlated error less than or equal to 0.1%, and a long-term correlated error less than or equal to 0.05%. The effects of process design on materials accounting are identified. Major areas of concern include the voloxidizer, the continuous dissolver, and the accountability tank.

  15. Materials accounting in a fast-breeder-reactor fuels-reprocessing facility: optimal allocation of measurement uncertainties

    International Nuclear Information System (INIS)

    This report describes the conceptual design of a materials accounting system for the feed preparation and chemical separations processes of a fast breeder reactor spent-fuel reprocessing facility. For the proposed accounting system, optimization techniques are used to calculate instrument measurement uncertainties that meet four different accounting performance goals while minimizing the total development cost of instrument systems. We identify instruments that require development to meet performance goals and measurement uncertainty components that dominate the materials balance variance. Materials accounting in the feed preparation process is complicated by large in-process inventories and spent-fuel assembly inputs that are difficult to measure. To meet 8 kg of plutonium abrupt and 40 kg of plutonium protracted loss-detection goals, materials accounting in the chemical separations process requires: process tank volume and concentration measurements having a precision less than or equal to 1%; accountability and plutonium sample tank volume measurements having a precision less than or equal to 0.3%, a shortterm correlated error less than or equal to 0.04%, and a long-term correlated error less than or equal to 0.04%; and accountability and plutonium sample tank concentration measurements having a precision less than or equal to 0.4%, a short-term correlated error less than or equal to 0.1%, and a long-term correlated error less than or equal to 0.05%. The effects of process design on materials accounting are identified. Major areas of concern include the voloxidizer, the continuous dissolver, and the accountability tank

  16. Development of magnetic flux leakage technique for examination of steam generator tubes of prototype fast breeder reactor

    International Nuclear Information System (INIS)

    Highlights: • For non-destructive detection of small localized defects in SG tubes of PFBR, tandem GMR array sensors based MFL technique developed. • 3D-finite element modeling performed for optimization of magnetizing current and spacing between the magnetizing coils. • The optimized magnetizing structure with ferrite core and guides detected 0.54 mm deep OD circumferential notch, 0.56 mm deep flat bottom hole, and 1.08 mm diameter hole in the tube with a SNR better than 6 dB. • Images of notches have been obtained using the tandem GMR array sensor. • The use of MFL and remote field eddy current techniques is expected to ensure comprehensive inspection of SG tubes of PFBR. - Abstract: For non-destructive examination of small diameter (outer diameter, OD 17.2 mm) and thick walled (wall thickness, 2.3 mm) ferromagnetic Modified 9Cr–1Mo steel steam generator (SG) tubes of Prototype Fast Breeder Reactor (PFBR), this paper proposes magnetic flux leakage (MFL) technique. Three dimensional finite element (3D-FE) modeling has been performed to optimize the magnetizing unit and inter-coil spacing of bobbin coils used for axial magnetization of the tube. The performance of the technique has been evaluated experimentally by measuring the axial (Ba) component of the leakage fields from localized machined defects in SG tubes. The MFL technique has shown capability to detect and image tube outside defects with a signal-to-noise ratio (SNR) better than 6 dB. Study reveals that Inconel support plates surrounding the SG tubes do not influence the MFL signals. As the MFL technique can detect localized defects in the presence of support plates as well as sodium and the remote field eddy current technique is sensitive to distributed wall thinning, their combined use will ensure comprehensive inspection of the SG tubes

  17. Radiation, welding, temperature and strain rate influence of material properties in fast breeder reactors

    Energy Technology Data Exchange (ETDEWEB)

    Albertini, C.; Montagnani, M. (J.R.C., ISPRA Establishment, ISPRA); Cenerini, R.; Curioni, S. (Bologna Univ. (Italy))

    1980-01-01

    Dynamic monoaxial tensile tests were performed to determine stress-strain diagrams for strain rates between 10/sup -2/ and 10/sup 3/ s/sup -1/. Temperatures were ambinet, 400deg and 550degC. The techniques used at high strains rate were that of the Hopkinson bar with pre-stressed bar loading device, and a hydropneumatic machine. Low strain rates were obtained with conventional testing machines. Test pieces for the investigation of the effects of welding were manufactured in order to observe the mechanical properties of weld material and of the heat-affected zone. The irradiation was performed in the Rapsodie reactor, up to a damage of 2.2 dpa, in a sodium environment at a temperature of 400degC. The irradiation was continued in the HFR, up to a damage of 10 and 30 dpa. The results of these later irradiations are not yet available. As far as welding is concerned, it should be noted that: at both room and high temperatures, the high deformation rate induces remarkable instabilities in the flow curves of weld and H.A.Z. materials as compared with the virgin material and with the ''static'' flow curve of the same material; at high temperature both the weld and H.A.Z. materials show strain rate sensitivities of opposite signs with respect to the virgin material. It is possible to observe that the strength of the two welded materials decreases and that of the virgin material increases or remains constant as the strain rate increases. Furthermore, the fracture strain of the weld and H.A.Z. materials decreases while that of the virgin material remains constant as strain rate increases. The main effects of irradiation are the substantial increase in the flow stress in tests performed at ambinet temperature and the drastic reduction in ductility with respect to the virgin and thermally aged material. At high temperature the flow stress of the irradiated material tends to decrease slightly with increasing strain rate.

  18. Water simulation experiments on the instantaneous source term of a severe breeder reactor accident

    International Nuclear Information System (INIS)

    FAUST is an experimental program to give contributions to the assessment of the instantaneous source term in case of an LMFBR loss-of-flow accident with expanding fuel or sodium vapor. In the FAUST 1a-series, experiments with discharge of a gas-particle mixture (nitrogen from 0.3 to 2.0 MPa with iron or nickel powder of different particle size) from a 1.45 liter source into a water pool cylinder of 28.8 cm diameter and 1 m height by rupture disks were performed at different pool height (0.90 cm). The system was closed, i.e. no openings were provided in the cover plate. Important measuring instruments were high-speed cameras, pressure transducers and magnets for article trapping in the cover gas. The most important quantity to be determined was the retention factor RF, defined as the ratio of the amount of particles discharged to the amount trapped in the cover gas. Furthermore, the expansion characteristics of the bubble, the correlated cover gas phenomena, the oscillation period and the entrainment were considered. In most cases, particle release stayed below detection limit, which corresponds to RF > 104. For the 1B series, using the same source, a larger pool vessel (63 cm diameter, 60 cm height) was installed and a cover plate with two openings of 4 cm diameter to simulate leaks. The discharge pressure was varied from 0.002 to 4 MPa. Other experimental parameters were pool height (0.50 cm), particles size (1 to 100 μm), and leak size. A release of airborne particles was found only at very low discharge pressure. At high pressure, major amounts of water were released, whereas the release of particles remained below detection limit (retention factor > 104). The oscillation period was of the order of 80 msec for 1A and 50 msec for 1B. Approximative calculations have shown that the large particle absorption may be explained by impaction during the bubble oscillations. (orig.)

  19. Nuclear proliferation and civilian nuclear power: report of the Nonproliferation Alternative Systems Assessment Program. Volume IX. Reactor and fuel cycle descriptions

    International Nuclear Information System (INIS)

    The Nonproliferation Alternative Systems Assessment Program (NASAP) has characterized and assessed various reactor/fuel-cycle systems. Volume IX provides, in summary form, the technical descriptions of the reactor/fuel-cycle systems studied. This includes the status of the system technology, as well as a discussion of the safety, environmental, and licensing needs from a technical perspective. This information was then used in developing the research, development, and demonstration (RD and D) program, including its cost and time frame, to advance the existing technology to the level needed for commercial use. Wherever possible, the cost data are given as ranges to reflect the uncertainties in the estimates. Volume IX is divided into three sections: Chapter 1, Reactor Systems; Chapter 2, Fuel-Cycle Systems; and the Appendixes. Chapter 1 contains the characterizations of the following 12 reactor types: light-water reactor; heavy-water reactor; water-cooled breeder reactor; high-temperature gas-cooled reactor; gas-cooled fast reactor; liquid-metal fast breeder reactor; spectral-shift-controlled reactor; accelerator-driven reactor; molten-salt reactor; gaseous-core reactor; tokamak fusion-fisson hybrid reactor; and fast mixed-spectrum reactor. Chapter 2 contains similar information developed for fuel-cycle facilities in the following categories: mining and milling; conversion and enrichment; fuel fabrication; spent fuel reprocessing; waste handling and disposal; and transportation of nuclear materials

  20. Nuclear proliferation and civilian nuclear power: report of the Nonproliferation Alternative Systems Assessment Program. Volume IX. Reactor and fuel cycle descriptions

    Energy Technology Data Exchange (ETDEWEB)

    1979-12-01

    The Nonproliferation Alternative Systems Assessment Program (NASAP) has characterized and assessed various reactor/fuel-cycle systems. Volume IX provides, in summary form, the technical descriptions of the reactor/fuel-cycle systems studied. This includes the status of the system technology, as well as a discussion of the safety, environmental, and licensing needs from a technical perspective. This information was then used in developing the research, development, and demonstration (RD and D) program, including its cost and time frame, to advance the existing technology to the level needed for commercial use. Wherever possible, the cost data are given as ranges to reflect the uncertainties in the estimates. Volume IX is divided into three sections: Chapter 1, Reactor Systems; Chapter 2, Fuel-Cycle Systems; and the Appendixes. Chapter 1 contains the characterizations of the following 12 reactor types: light-water reactor; heavy-water reactor; water-cooled breeder reactor; high-temperature gas-cooled reactor; gas-cooled fast reactor; liquid-metal fast breeder reactor; spectral-shift-controlled reactor; accelerator-driven reactor; molten-salt reactor; gaseous-core reactor; tokamak fusion-fisson hybrid reactor; and fast mixed-spectrum reactor. Chapter 2 contains similar information developed for fuel-cycle facilities in the following categories: mining and milling; conversion and enrichment; fuel fabrication; spent fuel reprocessing; waste handling and disposal; and transportation of nuclear materials.

  1. Design and manufacture of tube to tubesheet joints of steam generator for 500 MWe Prototype Fast Breeder Reactor

    International Nuclear Information System (INIS)

    Prototype Fast Breeder Reactor (PFBR) is 500 MWe pool type sodium cooled fast reactor. Presently this reactor is at advanced stage of construction at Kalpakkam. The main function of the steam generator is to extract the reactor heat through secondary sodium system and convert the feed water into superheated steam in the tubes of steam generators. The steam generator is a vertical shell and tube type heat exchanger with liquid sodium in the shell side and water/steam in the tube side. Operating experience of FBRs have shown that steam generator (SG) holds the key to commercial success of such reactors. Tube leakage is a serious problem and the prevention of sodium water reaction incident in the SG is essential to maintain the plant availability. In case of crack/failure in tube, high pressure water/steam reacts with shell side sodium and results in exothermic reaction with evolution of hydrogen, corrosive reaction products and intense local heat depending on leak size. This high reactive nature of sodium with water/steam requires that sodium to water/steam boundaries of steam generators must possess a high degree of reliability against failure. This is achieved in design and manufacturing by maximising the tube integrity and more importantly by proper selection of tube to tubesheet joint configuration. The principal material of construction of SG is Modified 9Cr-1Mo steel. The tubes are seamless and produced by electric arc melting followed by Electro Slag Refining (ESR) with tight control on inclusion content. Ultrasonic and eddy current testing is done on entire tube length in accordance with ASME SEC III Class I. Long seamless tubes (each 23m) are used in order to reduce the number of tube to tubesheet welds.Each SG has 547 tubes and there are 9 SG in the reactor including one spare module. There is no tube to tube joint as the aim is to minimise the number of welds to increase reliability.Tube to tubesheet joint selected for PFBR steam generator is of internal

  2. Tritium-assisted fusion breeders

    International Nuclear Information System (INIS)

    This report undertakes a preliminary assessment of the prospects of tritium-assisted D-D fuel cycle fusion breeders. Two well documented fusion power reactor designs - the STARFIRE (D-T fuel cycle) and the WILDCAT (Cat-D fuel cycle) tokamaks - are converted into fusion breeders by replacing the fusion electric blankets with 233U producing fission suppressed blankets; changing the Cat-D fuel cycle mode of operation by one of the several tritium-assisted D-D-based modes of operation considered; adjusting the reactor power level; and modifying the resulting plant cost to account for the design changes. Three sources of tritium are considered for assisting the D-D fuel cycle: tritium produced in the blankets from lithium or from 3He and tritium produced in the client fission reactors. The D-D-based fusion breeders using tritium assistance are found to be the most promising economically, especially the Tritium Catalyzed Deuterium mode of operation in which the 3He exhausted from the plasma is converted, by neutron capture in the blanket, into tritium which is in turn fed back to the plasma. The number of fission reactors of equal thermal power supported by Tritium Catalyzed Deuterium fusion breeders is about 50% higher than that of D-T fusion breeders, and the profitability is found to be slightly lower than that of the D-T fusion breeders

  3. Critical review of the literature on high energy release during hypothetical core disruptive accidents in sodium-cooled fast breeder reactors

    International Nuclear Information System (INIS)

    Upon the request of the ''Enquete-Kommission'' on Future Nuclear Energy Policy set up by the German Federal Parliament, a literature survey has been compiled on all scientific studies of Bethe-Tait accidents with high potentials of mechanical energy releases (''Literaturuebersicht zu allen wissenschaftlichen Arbeiten ueber Bethe-Tait-Stoerfaelle mit hohem mechanischem Energiefreisetzungspotential''). The study is a critical review of all relevant scientific publications and studies by the international scientific community in this field, which are devoted to high mechanical energy releases from major accidents in sodium cooled fast breeder reactors, or at least indicate the potential for high energy releases. These publications are evaluated with respect to their relevance to the design base levels of the SNR 300. In accordance with the wishes expressed by the ''Enquete-Kommission'', the study not only deals with the arguments and findings by scientists from national research centers and from the fast breeder development association, but also takes into account the arguments and findings by working groups in Germany and abroad, which represent different attitudes vis-a-vis the utilization of nuclear power and the fast breeder reactor. The study was handed over to the ''Enquete-Kommission'' in 1982. The present version differs in some minor points from the original version. The conclusion to be drawn from the examination of the bulk of the above mentioned information is this: - For the SNR 300 the occurence of major accidents with mechanical energy releases exceeding the design limit of 370 MWs can be excluded with a probability verging on certainty, i.e., to all practical intents and purposes. (orig.)

  4. NCSU reactor sharing program. Final technical report

    International Nuclear Information System (INIS)

    The Nuclear Reactor Program at North Carolina State University provides the PULSTAR Research Reactor and associated facilities to eligible institutions with support, in part, from the Department of Energy Reactor Sharing Program. Participation in the NCSU Reactor Sharing Program continues to increase steadily with visitors ranging from advance high school physics and chemistry students to Ph.D. level research from neighboring universities. This report is the Final Technical Report for the DOE award reference number DE-FG05-95NE38136 which covers the period September 30, 1995 through September 30, 1996

  5. Analysis of thorium/U-233 lattices and cores in a breeder/burner heavy water reactor

    International Nuclear Information System (INIS)

    Due to the inevitable dwindling of uranium resources, advanced fuel cycles in the current generation of reactors stand to be of great benefit in the future. Heavy water moderated reactors have much potential to make use of thorium, a currently unexploited resource. Core fuelling configurations of a Heavy Water Reactor based on the self-sufficient thorium fuel cycle were simulated using the DRAGON and DONJON reactor physics codes. Three heterogeneously fuelled reactors and one homogeneously fuelled reactor were studied. (author)

  6. U.S. Domestic Reactor Conversion Programs

    International Nuclear Information System (INIS)

    The Conversion Projects Include: the revision of the facilities safety basis documents and supporting analysis, the fabrication of new LEU fuel, the change-out of the reactor core, and the removal of the used HEU fuel (by INL University Fuels Program or DOE-NE). The major entities involved are: the U.S. Nuclear Regulatory Commission, the University reactor department, the fuel and hardware fabricators, the Spent fuel receipt facilities, the Spent fuel shipping services, and the U.S. Department of Energy and their subcontractors. Three major Reactor Conversion Program milestones have been accomplished since 2006: the conversion of the TRIGA reactor at Texas A and M University Nuclear Science Center, the conversion of the University of Florida Training Reactor, and the conversion of the Purdue University Reactor. Four Reactor Conversion Program milestones yet to be accomplished in 2008 and 2009: the Washington State University Nuclear Radiation Center reactor, the Oregon State University TRIGA Reactor, the University of Wisconsin Nuclear Reactor, and the Neutron Radiography Reactor Facility. NNSA is committed to doing things cheaper, better, smarter, safer through a 'Lessons Learned' process. The conversion team assessed each major activity grouping: Project Initiation, Conversion Proposal Development, Fuel Fabrication and Hardware, Core Conversion, and Spent Nuclear Fuel Removal. Issues were identified and recommendations were given

  7. Analysis of unprotected transients with control and safety rod drive mechanism expansion feedback in a medium sized oxide fuelled fast breeder reactor

    Energy Technology Data Exchange (ETDEWEB)

    Sathiyasheela, T., E-mail: sheela@igcar.gov.in; Natesan, K.; Srinivasan, G.S.; Devan, K.; Puthiyavinayagam, P.

    2015-09-15

    Highlights: • Possibilities of enhancing safety under ULOF and UTOP accidents. • CSRDM expansion feedbacks under unprotected transients. • CSRDM expansion feedback enhances the safety of fast reactors. • CSRDM expansion feedbacks ensuring enough time for initiating safety actions. - Abstract: Possibilities of enhancing core safety under unprotected loss of flow (ULOF) and unprotected transient over power (UTOP) accidents with control and safety rod drive mechanism (CSRDM) expansion feedbacks are explored in a medium sized oxide fuelled fast breeder reactor. This feedback is expected to take the reactor to a safe shutdown under ULOF and to an another steady state under UTOP where there is no significant fuel melting. Under ULOF, with CSRDM feedback net reactivity was maintained negative throughout the transient (up to 2000 s) and the power dropped to a level of heat removal capacity of decay heat removal system based on natural circulation. Similarly, under UTOP with the above feedback reactor power goes to a lower peak value. The fuel temperature is just touching the melting temperature and the melt fraction does not cross 5%. With CSRDM expansion feedbacks both ULOF and UTOP transients prolong beyond 2000 s. It ensures, availability of time for initiating any safety actions against the transients, and thus it helps to preclude core disruptive accidents (CDA) in a medium sized oxide fuelled reactors.Classification: L. safety and risk analysis.

  8. Programming for a nuclear reactor instrument simulator

    International Nuclear Information System (INIS)

    A new computerized control system for a transient test reactor incorporates a simulator for pre-operational testing of control programs. The part of the simulator pertinent to the discussion here consists of two microprocessors. An 8086/8087 reactor simulator calculates simulated reactor power by solving the reactor kinetics equations. An 8086 instrument simulator takes the most recent power value developed by the reactor simulator and simulates the appropriate reading on each of the eleven reactor instruments. Since the system is required to run on a one millisecond cycle, careful programming was required to take care of all eleven instruments in that short time. This note describes the special programming techniques used to attain the needed performance

  9. U.S. fast reactor materials and structures program

    International Nuclear Information System (INIS)

    The U.S. DOE has sponsored a vigorous breeder reactor materials and structures program for 15 years. Important contributions have resulted from this effort in the areas of design (inelastic rules, verified methods, seismic criteria, mechanical properties data); resolution of licensing issues (technical witnessing, confirmatory testing); construction (fabrication/welding procedures, nondestructive testing techniques); and operation (sodium purification, instrumentation and chemical analysis, radioactivity control, and in-service inspection. The national LMFBR program currently is being restructured. The Materials and Structures Program will focus its efforts in the following areas: (1) removal of anticipated licensing impediments through confirmation of the adequacy of structural design methods and criteria for components containing welds and geometric discontinuities, the generation of mechanical properties for stainless steel castings and weldments, and the evaluation of irradiation effects; (2) qualification of modified 9 Cr-1 Mo steel and tribological coatings for design flexibility; (3) development of improved inelastic design guidelines and procedures; (4) reform of design codes and standards and engineering practices, leading to simpler, less conservative rules and to simplified design analysis methods; and (5) incorporation of information from foreign program

  10. The US Liquid Metal Reactor Development Program

    International Nuclear Information System (INIS)

    The US Liquid Metal Reactor Development Program has been restructured to take advantage of the opportunity today to carry out R and D on truly advanced reactor technology. The program gives particular emphasis to improvements to reactor safety. The new directions are based on the technology of the Integral Fast Reactor (IFR). Much of the basis for superior safety performance using IFR technology has been experimentally verified and aggressive programs continue in EBR-II and TREAT. Progress has been made in demonstrating both the metallic fuel and the new electrochemical processes of the IFR. The FFTF facility is converting to metallic fuel; however, FFTF also maintains a considerable US program in oxide fuels. In addition, generic programs are continuing in steam generator testing, materials development, and, with international cooperation, aqueous reprocessing. Design studies are carried out in conjunction with the IFR technology development program. In summary, the US maintains an active development program in Liquid Metal Reactor technology, and new directions in reactor safety are central to the program

  11. Nuclear reactors. To breed or not to breed. A Pugwash debate on fast breeder reactors held at the Royal Society, London, on 28 September 1976 under the chairmanship of Sir Alec Merrison

    International Nuclear Information System (INIS)

    The debate which is reported was timed to coincide with the publication of the Report of the (UK) Royal Commission on Environmental Pollution: 'Nuclear Power and Environment'. The volume comprises an introductory section, a report of an address by the Chairman of the Royal Commission and invited papers on fast breeder reactors in relation to energy requirements, on the safety of a commercial fast reactor, on processing and reprocessing of fuel, on radioactive waste management, and on diversion of plutonium and proliferation of nuclear weapons. An edited version of the discussion is presented under the following heads: comments on the report of the Royal Commission; projections of future energy requirement; thermal pollution; safety and insurance of reactors; reprocessing of fuel; storage and disposal of wastes; energy from fusion; utilization of coal; and proliferation of weapons and diversion of plutonium. The six invited papers are considered to be within INIS scope and separate abstracts have been prepared. (U.K.)

  12. Status and prospects of thermal breeders

    International Nuclear Information System (INIS)

    The main objective of this cooperative study and of this report is to evaluate the extent to which thermal breeders might complement or serve as an alternative to fast breeders in solving the long-term nuclear fuel supply problem. A secondary objective is to consider in a general way issues such as proliferation, safety, environmental impacts, economics, power plant availability, and fuel cycle versatility to determine whether thermal breeder reactors offer advantages or disadvantages with respect to such issues

  13. Study on laser welding of fuel clad tubes and end plugs made of modified 9Cr-1Mo steel for metallic fuel of Fast Breeder Reactors

    Science.gov (United States)

    Harinath, Y. V.; Gopal, K. A.; Murugan, S.; Albert, S. K.

    2013-04-01

    A procedure for Pulsed Laser Beam Welding (PLBW) has been developed for fabrication of fuel pins made of modified 9Cr-1Mo steel for metallic fuel proposed to be used in future in India's Fast Breeder Reactor (FBR) programme. Initial welding trials of the samples were carried out with different average power using Nd-YAG based PLBW process. After analyzing the welds, average power for the weld was optimized for the required depth of penetration and weld quality. Subsequently, keeping the average power constant, the effect of various other welding parameters like laser peak power, pulse frequency, pulse duration and energy per pulse on weld joint integrity were studied and a procedure that would ensure welds of acceptable quality with required depth of penetration, minimum size of fusion zone and Heat Affected Zone (HAZ) were finalized. This procedure is also found to reduce the volume fraction delta-ferrite in the fusion zone.

  14. Report on the shearing, dissolution and analysis of GRIP-II rod 79-453 (validation rod); Light Water Breeder Reactor proof-of-breeding analytical support project

    International Nuclear Information System (INIS)

    This report covers the processing and analysis of the fuel-bearing section (M-5138) of an irradiated experimental Light Water Breeder Reactor fuel rod, GRIP-II rod No. 79-453; this section has been designated the Validation Rod. Process steps included precision shearing of the rod into eight comminuted segments, dissolution of the segments, and chemical and radiometric analyses of the resulting solutions. The shearing and dissolution were carried out fully remotely in an existing pilot-scale facility installed in a shielded cell. Data are provided on physical parameters of the rod section and segments, uranium assays and isotopic abundances, and selected fission products. An error analysis of the individual measurements and analyses is included

  15. Optimization of U–Th fuel in heavy water moderated thermal breeder reactors using multivariate regression analysis and genetic algorithms

    International Nuclear Information System (INIS)

    Highlights: • A new method useful for the parametric analysis and optimization of reactor core designs. • This uses the strengths of genetic algorithms (GA), and regression splines. • The method is applied to the core fuel pin cell of a PHWR design. • Tools like java, R, and codes like Serpent, Matlab are used in this research. - Abstract: An analysis and optimization of a set of neutronics parameters of a thorium-fueled pressurized heavy water reactor core fuel has been performed. The analysis covers a detailed pin-cell analysis of a seed-blanket configuration, where the seed is composed of natural uranium, and the blanket is composed of thorium. Genetic algorithms (GA) is used to optimize the input parameters to meet a specific set of objectives related to: infinite multiplication factor, initial breeding ratio, and specific nuclide’s effective microscopic cross-section. The core input parameters are the pitch-to-diameter ratio, and blanket material composition. Recursive partitioning of decision trees (rpart) multivariate regression model is used to perform a predictive analysis of the samples generated from the GA module. Reactor designs are usually complex and a simulation needs a significantly large amount time to execute, hence implementation of GA or any other global optimization techniques is not feasible, therefore we present a new method of using rpart in conjunction with GA. Due to using rpart, we do not necessarily need to run the neutronics simulation for all the inputs generated from the GA module rather, run the simulations for a predefined set of inputs, build a regression fit to the input and the output parameters, and then use this fit to predict the output parameters for the inputs generated by GA. The rpart model is implemented as a library using R programming language. The results suggest that the initial breeding ratio tends to increase due to a harder neutron spectrum, however a softer neutron spectrum is desired to limit the

  16. Artificial intelligence program in a computer application supporting reactor operations

    International Nuclear Information System (INIS)

    Improving nuclear reactor power plant operability is an ever-present concern for the nuclear industry. The definition of plant operability involves a complex interaction of the ideas of reliability, safety, and efficiency. This paper presents observations concerning the issues involved and the benefits derived from the implementation of a computer application which combines traditional computer applications with artificial intelligence (AI) methodologies. A system, the Component Configuration Control System (CCCS), is being installed to support nuclear reactor operations at the Experimental Breeder Reactor II

  17. Efficacy of several Salmonella vaccination programs against experimental challenge with Salmonella gallinarum in commercial brown layer and broiler breeder hens

    Directory of Open Access Journals (Sweden)

    JB de Paiva

    2009-03-01

    Full Text Available The protective effect of various Salmonella vaccines regimens against an experimental Salmonella Gallinarum challenge (SGNalr strain at 12 wk of age was evaluated in two experiments. In Experiment 1 commercial brown layers were vaccinated according to one of the following programs: (i two doses of a SE bacterin (Layermune SE; group 1; (ii a first dose of a live SG9R vaccine (Cevac SG9R followed by a SE bacterin (Layermune SE; group 2; (iii one dose of each of two different multivalent inactivated vaccines containing SE cells (Corymune 4 & Corymune 7; group 3 or (iv not vaccinated (group 4. In Experiment 2, broiler breeders were given the same vaccination treatments except for the group vaccinated with the multivalent vaccines. Overall, in both experiments, all vaccination schemes were effective in reducing mortality after challenge with a SG field strain. Primary vaccination with an initial dose of a live SG9R vaccine followed some weeks later by a dose of an inactivated SE bacterin was the most effective (p<0.05 vaccination program against mortality induced by field SG experimental challenge in both experiments. In conclusion, Salmonella vaccination programs containing SE bacterins alone or in combination with a live SG9R vaccine are effective in preventing mortality induced by infection of field SG. Nevertheless, it is important to emphasize that any vaccination program against any Salmonella serotype will only be effective if it is part of a sound and comprehensive biosecurity program designed for Salmonella control in poultry farms.

  18. Developmental Light-Water Reactor Program

    International Nuclear Information System (INIS)

    This report summarizes the progress of the Developmental Light-Water Reactor (DLWR) Program at Oak Ridge National Laboratory in FY 1989. It also includes (1) a brief description of the program, (2) definition of goals, (3) earlier achievements, and (4) proposed future activities

  19. AFRRI TRIGA Reactor water quality monitoring program

    International Nuclear Information System (INIS)

    AFRRI has started a water quality monitoring program to provide base line data for early detection of tank leaks. This program revealed problems with growth of algae and bacteria in the pool as a result of contamination with nitrogenous matter. Steps have been taken to reduce the nitrogen levels and to kill and remove algae and bacteria from the reactor pool. (author)

  20. Program summary for the Civilian Reactor Development Program

    Energy Technology Data Exchange (ETDEWEB)

    None

    1982-07-01

    This Civilian Reactor Development Program document has the prime purpose of summarizing the technical programs supported by the FY 1983 budget request. This section provides a statement of the overall program objectives and a general program overview. Section II presents the technical programs in a format intended to show logical technical interrelationships, and does not necessarily follow the structure of the formal budget presentation. Section III presents the technical organization and management structure of the program.

  1. Advanced Reactors Transition Program Resource Loaded Schedule

    Energy Technology Data Exchange (ETDEWEB)

    GANTT, D.A.

    2000-01-12

    The Advanced Reactors Transition (ART) Resource Loaded Schedule (RLS) provides a cost and schedule baseline for managing the project elements within the ART Program. The Fast Flux Test Facility (FETF) activities are delineated through the end of FY 2000, assuming continued standby. The Nuclear Energy (NE) Legacies and Plutonium Recycle Test Reactor (PRTR) activities are delineated through the end of the deactivation process. This revision reflects the 19 Oct 1999 baseline.

  2. Advanced Reactors Transition Program Resource Loaded Schedule

    Energy Technology Data Exchange (ETDEWEB)

    BOWEN, W.W.

    1999-11-08

    The Advanced Reactors Transition (ART) Resource Loaded Schedule (RLS) provides a cost and schedule baseline for managing the project elements within the ART Program. The Fast Flux Test Facility (FFTF) activities are delineated through the end of FY 2000, assuming continued standby. The Nuclear Energy (NE) Legacies and Plutonium Recycle Test Reactor (PRTR) activities are delineated through the end of the deactivation process. This document reflects the 1 Oct 1999 baseline.

  3. Possible types of breeders with thorium cycle

    International Nuclear Information System (INIS)

    Neutronics calculations of simplified homogeneous reactor models show the possibility that metal-fueled LMFBRs and coated particle fueled gas cooled reactors achieve reactor doubling times of around 10 years with the thorium cycle. Three concepts of gas-cooled thorium cycle breeders are discused. (Author)

  4. TITAN program and direct cycle fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kato, Yasuyoshi; Yoshizawa, Yoshio; Nitawaki, Takeshi [Research Laboratory for Nuclear Reactors, Tokyo Institute of Technology, Tokyo (Japan)

    2000-07-01

    In December 1999, the Research Laboratory for Nuclear Reactors of the Tokyo Institute of Technology (TIT) started a new program for the development of advanced nuclear reactors with small and medium size. TITAN is the acronym for the program. A novel concept of a carbon dioxide cooled direct cycle fast reactor with a Rankin cycle has been proposed as the advanced nuclear reactors and evaluated for an alternative option to liquid metal cooled fast reactors (LMFRs). The use of carbon dioxide as coolant eliminates major safety related problems of sodium cooled fast reactors: positive sodium void reactivity, hazardous reaction between sodium and water or air. The decay heat is passively removed by allocating a storage tank of liquidized carbon dioxide between the regenerator and the condenser, and by introducing naturally the carbon dioxide vaporized from the tank into the core in the event of the depressurization accident. The direct cycle results in considerable simplification of the heat transport system owing to the absence of intermediate cooling and water-steam loops comparing with the LMFRs. The thermal efficiency of the direct cycle is evaluated as 34.3 %, which is slightly higher than those in the current BWRs and PWRs. (author)

  5. The program of reactors and nuclear power plants

    International Nuclear Information System (INIS)

    Into de framework of the program of research reactors and nuclear power plants, the operating Argentine reactors are described. The uses of the research reactors in Argentina are summarized. The reactors installed by Argentina in other countries (Peru, Algeria, Egypt) are briefly described. The CAREM project for the design and construction of an innovator small power reactor (27 MWe) is also described in some detail. The next biennial research and development program for reactor is briefly outlined

  6. An evaluation of light water breeder reactor system (LWBR) as an alternative for nuclear power generation in Brazil

    International Nuclear Information System (INIS)

    The LWBR system as an alternative for nuclear power generation in Brazil, was technically and economically evaluated. The LWBR system has been characterized comparatively with the Pressurized Water Reactors through technological and investment cost analysis and through the analysis of the processes and unit costs of the fuel cycle stages. The characteristics of the LWBR system in comparison to the PWR system, with respect to utilization and cumulative consumption of uranium and thorium resources, fuel cycle processes and associated costs have been determined for possible alternatives of nuclear power participation in the Brazilian hidro-thermal electricity generating system. The analysis concluded that the LWBR system does not represent an attractive alternative for nuclear power generation in Brazil and even has no potential to compete with conventional Pressurized Water Reactors. (Author)

  7. Post-scram Liquid Metal cooled Fast Breeder Reactor (LMFBR) neat transport system dynamics and steam generator control

    Science.gov (United States)

    Brukx, J. F. L. M.

    1982-06-01

    Loop type LMFBR heat transport system dynamics after reactor shutdown and during subsequent decay heat removal are considered with emphasis on steam generator dynamics including the development and evaluation of various post-scram steam generator control systems, and natural circulation of the sodium coolant, including the influence of superimposed free convection on forced convection heat transfer and pressure drop. The normal operating and decay heat removal functions of the overall heat transport system are described.

  8. The radiological consequences of notional accidental releases of radioactivity from fast breeder reactors: sensitivity to the dose-effect relationships adopted for early biological effects

    International Nuclear Information System (INIS)

    This study considered the sensitivity to the dose-response relationships adopted for the estimation of early biological effects from notional accidental releases of radioactivity from fast breeder reactors. Two distinct aspects were considered: the sensitivity of the predicted consequences to variation in the dose-mortality relationships for irradiation of the bone marrow and the lung; and the influence of simple supportive medical treatment in reducing the incidence of early deaths in the exposed population. The numbers of early effects estimated in the initial study were relatively insensitive to variation in the dose-mortality relationships within the bounds proposed. The few exceptions concerned releases of particular nuclide composition, and the variation in the predicted consequences could be around an order of magnitude; the absolute numbers of effects however were in general small when the sensitivity was most pronounced. The reduction in the incidence of early deaths when using simple supportive treatment varied markedly with the nuclide composition of the release. Areas of uncertainty were identified where further research and investigation might most profitably be directed with a view to improving the reliability of the dose-effect relationships adopted and hence of the predicted consequences of the release considered. (author)

  9. Diagnostic agent using parasitic discrete wavelet transform for the hybrid diagnostic agent system for the fast-breeder reactor 'Monju'

    International Nuclear Information System (INIS)

    In order to detect anomalies in rotating machines such as pumps at an early stage, we developed a system using wavelet transform. The pump diagnostic experiment equipment was designed taking into consideration the structure of the pump used for the water-steam system of the fast breeder reactor 'Monju'. For improving detection capability, it is desirable to use a mother wavelet (MW) whose shape is similar to the anomaly signal that is required to be detected. We call the constructed MW on the basis of the real signal the real mother wavelet (RMW). The parasitic discrete wavelet transform (P-DWT) that has a large flexibility in design of the MW and a high processing speed was applied for detecting process signals. The vibration and sound signals were measured using the pump diagnostic experiment equipment when three types of anomalies (injection of an object, change of a balance of the impeller, and damage to the axis of the impeller) occur. Complex RMWs were constructed on the basis of the measured signals, and subsequently, parasitic filters were constructed. Signal detection was performed by calculating the fast wavelet instantaneous correlation using the parasitic filter. We evaluated three types of anomalies, and found that P-DWT is useful for detecting these anomalies. Furthermore, we developed a diagnostic agent using P-DWT as one of the diagnostic agents of our hybrid diagnostic agent system, which is intended to work together with the 'Monju' distributed diagnostic agent system. (author)

  10. Site suitability report in the matter of Clinch River Breeder Reactor Plant. Docket No. 50-537. Revision to March 4, 1977 report

    International Nuclear Information System (INIS)

    In March 1977, the Office of Nuclear Reactor Regulation issued its Site Suitability Report (SSR) for the proposed Clinch River Breeder Plant (CRBRP). That SSR documents the result of the staff's evaluation of the suitability of the proposed CRBRP site for a facility of the general size and type as the CRBRP from the standpoint of radiological health and safety considerations. The staff concluded in that SSR that the proposed CRBRP site is suitable for such a facility. Since the SSR was issued, several modifications have been made to the CRBRP design, additional data related to the site and its environs have been collected, and the Fast Flux Test Facility, a technological precursor to the CRBRP, has been completed and has commenced operation. In addition, new emergency planning requirements have been promulgated by the staff. This report is an update of the March 1977 SSR that reflects these matters and discusses them in terms of the previous staff conclusion regarding the suitability of the proposed CRBRP site

  11. Comparative analysis of quality assurance systems which effectively control, review and verify the quality of components manufactured for liquid metal cooled fast breeder reactors within the EEC

    International Nuclear Information System (INIS)

    Comparative analyses are made of Quality Assurance Systems, by techniques and the methodology used, for the manufacture of component parts for the Liquid Metal Cooled Fast Breeder Reactor (LMFBR) within the EEC. Two differing alternative systems are presented in the analysis. First, a tabulated analytical treatment which analyses 14 codes and standards relating to Quality Assurance which can be applied to LMFBR's. The comparison equates equivalent clauses between codes and standards followed by an analysis of individual clauses in tabular form, the International Standard ISO 6215. A statistical summary and recommendations conclude this analysis. The second alternative system used in the comparison is a descriptive analytical method applied to 9 selected codes and standards relating to Quality Assurance based on the 13 criteria of the International IAEA Code of Practice no. 50 C.QA entitled ''Quality Assurance for Safety in Nuclear Power Plants''. An investigation is then made of the state of the art on the subject of classification of component parts bearing generally on Quality Assurance. The method of classification is segregated into General, Safety and Inspection categories. A summary of destructive and non destructive controls that may be applied during the manufacture of LMFBR components is given, together with tests that may be applied to selected components, namely Primary Tank, Secondary Sodium Pump and the Primary Cold Trap allocated to Safety Classes, 1, 2 and 3 respectively. The report concludes with a summary of typical records produced at the delivery of a component

  12. Application of an LP model to breeder strategy studies

    International Nuclear Information System (INIS)

    The paper discusses the relationships between the capital cost differential (FBR--LWR) allowable for economic breeder introduction and energy demand, resource availability (through price--quantity schedule), and economic environment for a range of future projections. The ALPS linear programming reactor systems analysis code, developed by Hanford Engineering Development Laboratory, was used for economic optimizations where they were done, and where they were not it provided a useful tool to compute the discounted total system power cost over the planning horizon for a given set of reactor mix and cost parameters

  13. World Energy Data System (WENDS). Volume XI. Nuclear fission program summaries

    International Nuclear Information System (INIS)

    Brief management and technical summaries of nuclear fission power programs are presented for nineteen countries. The programs include the following: fuel supply, resource recovery, enrichment, fuel fabrication, light water reactors, heavy water reactors, gas cooled reactors, breeder reactors, research and test reactors, spent fuel processing, waste management, and safety and environment

  14. World Energy Data System (WENDS). Volume XI. Nuclear fission program summaries

    Energy Technology Data Exchange (ETDEWEB)

    1979-06-01

    Brief management and technical summaries of nuclear fission power programs are presented for nineteen countries. The programs include the following: fuel supply, resource recovery, enrichment, fuel fabrication, light water reactors, heavy water reactors, gas cooled reactors, breeder reactors, research and test reactors, spent fuel processing, waste management, and safety and environment. (JWR)

  15. Safety-Evaluation Report related to the construction of the Clinch River Breeder Reactor Plant. Docket No. 50-537

    International Nuclear Information System (INIS)

    The purpose of this appendix is to describe the staff's evaluation of hypothetical core disruptive accidents which, for analytical purposes, have been postulated to occur in the CRBR. This introduction is divided into three major parts. The first background information. The second provides an overview of potential CDA initiating events and consequences considered for the CRBR. The third describes the guidelines used in evaluating CDAs for the CRBR. A schematic view of major components of the reactor systems is provided. The staff's evaluation of the major areas associated with the assessment of CDAs is presented

  16. A review of fusion breeder blanket technology, part 1

    International Nuclear Information System (INIS)

    This report presents the results of a study of fusion breeder blanket technology. It reviews the role of the breeder blanket, the current understanding of the scientific and engineering bases of liquid metal and solid breeder blankets and the programs now underway internationally to resolve the uncertainities in current knowledge. In view of existing national expertise and experience, a solid breeder R and D program for Canada is recommended

  17. A generalized perturbation program for CANDU reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Do Heon; Kim, Jong Kyung [Hanyang University, Seoul (Korea, Republic of); Choi, Hang Bok; Roh, Gyu Hong [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of); Yang, Won Sik [Chosun University, Kwangju (Korea, Republic of)

    1998-12-31

    A generalized perturbation program has been developed for the purpose of estimating zonal power variation of a CANDU reactor upon refueling operation. The forward and adjoint calculation modules of RFSP code were used to construct the generalized perturbation program. The numerical algorithm for the generalized adjoint flux calculation was verified by comparing the zone power estimates upon refueling with those of forward calculation. It was, however, noticed that the truncation error from the iteration process of the generalized adjoint flux is not negligible. 2 refs., 1 figs., 1 tab. (Author)

  18. Possible types of breeders with thorium cycle

    International Nuclear Information System (INIS)

    Neutronics calculations of simplified homogeneous reactor models show the possibility that metal-fueled LMFBRs and coated particle fueled gas cooled reactors achieve doubling times of around 10 years with the thorium cycle. Three concepts of gas-cooled thorium cycle breeders are discussed. (Author)

  19. Final environmental statement, Liquid Metal Fast Breeder Reactor Program. Volume 2

    International Nuclear Information System (INIS)

    Included are copies of fifty-six comment letters on the Proposed Final Environmental Statement together with the ERDA replies to these letters. The letters were received from Federal, State, and local agencies, environmental and public interest groups, members of the academic and industrial communities, and individual citizens

  20. Final environmental statement, Liquid Metal Fast Breeder Reactor Program. Volume 3

    International Nuclear Information System (INIS)

    Included are copies of thirty-four comment letters on the Proposed Final Environmental Statement together with the ERDA replies to these letters. The letters were received from Federal, State, and local agencies, environmental and public interest groups, members of the academic and industrial communities, and individual citizens

  1. Fusion breeder neutronics. Final report

    International Nuclear Information System (INIS)

    Research efforts in fusion breeder neutronics have been focused on two tasks that are strongly related. Efforts in Task 1 concentrate on examining the required conditions to sustain fuel self-sufficiency in fusion reactors operated on a D-T fuel cycle. In this respect, in-depth and detailed engineering analyses have been performed on various blanket and reactor concepts to verify the potential of each blanket concept to exhibit a tritium breeding ratio (TBR) in excess of unity by a margin that compensates for losses, radioactive decay and other inventory requirements. Efforts in Task 2 concentrate on evaluating the overall uncertainties (both experimental and analytical) associated with the TBR

  2. Development of Education and Training Programs Using ISIS Research Reactor

    International Nuclear Information System (INIS)

    As a part of the French Alternative Energies and Atomic Energy Commission (CEA), the National Institute for Nuclear Science and Technology (INSTN) carries out various education and training programs on nuclear reactor theory and operation. These programs take advantage of the use of an extensive range of training tools that includes software applications, simulators, as well as the use of research reactors. After a presentation of ISIS reactor, we present the training courses that have been developed on ISIS reactor and their use in education and training programs developed by INSTN. We report on how the training courses carried out on ISIS research reactor ensure a practical and comprehensive understanding of the reactor principle and operation, bringing tremendous benefit to the trainees. We also discuss the future development of education and training programs using the ISIS research reactor as a very powerful tool for the development of the human resources needed by the nuclear industry and the nuclear programs. (author)

  3. Program status of the high temperature reactor development in the Federal Republic of Germany

    International Nuclear Information System (INIS)

    The status of the HTR development program in the Federal Republic of Germany in 1984 is characterized by the beginning of a transition phase from a national program to a commercial program. In the last 20 years the HTR technology program was strongly, nearly completely supported by the Federal Government and the State Government of North-Rhine-Westfalia. Funding of the program up to now exceeded 5 billion DM. Within this framework it was possible to establish competent-reactor-system companies, to enable industries to supply HTR- specific components including fuel elements and nuclear graphites, to maintain the strong engagement of the national centre KFA Juelich in general R and D activities, to build and operate the AVR-plant for more than 16 years, to erect the demonstration plant THTR-300 now approaching completion and to build and operate many efficient test facilities. Thereby the HTR technology development achieved a stage of maturity which is not only considered to be most advanced, but is also ready now for commerical deployment. The assessment report which comprised both the fast breeder and the HTR development included all major impacts, such as history, status, prospects, benefits, industrial aspects and international developments of the technology. The program description is facilitated by distinguishing the five major program elements: AVR, THTR-300, THTR follow-up plant, nuclear process heat program, fuel cycle activities

  4. Development of safety evaluation methods and analysis codes applied to the safety regulations for the design and construction stage of fast breeder reactor (Annual safety research report, JFY 2011)

    International Nuclear Information System (INIS)

    The purposes of this study are to develop the safety evaluation methods and analysis codes needed in the design and construction stage of fast breeder reactor (FBR). In JFY 2011, the following results are obtained. As for the development of safety evaluation methods needed in the safety examination achieved for the reactor establishment permission, development of the analysis codes such as core seismic analysis code, core safety analysis code and core damage analysis code were earned out according to the plan. As for the development of the safety evaluation method needed for the risk informed safety regulation, the quantification technique of the event tree using the Continuous Markov chain Monte Carlo method (CMMC method) were studied, and the seismic PSA to evaluate residual risk was studied. (author)

  5. Programming Guidelines for FBD Programs in Reactor Protection System Software

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Se Jin; Lee, Dong Ah; Kim, Eui Sub; Yoo, Jun Beom [Division of Computer Science and Engineering College of Information and Communication, Konkuk University, Seoul (Korea, Republic of); Lee, Jang Su [Man-Machine Interface System team Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    Properties of programming languages, such as reliability, traceability, etc., play important roles in software development to improve safety. Several researches are proposed guidelines about programming to increase the dependability of software which is developed for safety critical systems. Misra-c is a widely accepted programming guidelines for the C language especially in the sector of vehicle industry. NUREG/CR-6463 helps engineers in nuclear industry develop software in nuclear power plant systems more dependably. FBD (Function Block Diagram), which is one of programming languages defined in IEC 61131-3 standard, is often used for software development of PLC (programmable logic controllers) in nuclear power plants. Software development for critical systems using FBD needs strict guidelines, because FBD is a general language and has easily mistakable elements. There are researches about guidelines for IEC 61131-3 programming languages. They, however, do not specify details about how to use languages. This paper proposes new guidelines for the FBD based on NUREG/CR-6463. The paper introduces a CASE (Computer-Aided Software Engineering) tool to check FBD programs with the new guidelines and shows availability with a case study using a FBD program in a reactor protection system. The paper is organized as follows.

  6. Programming Guidelines for FBD Programs in Reactor Protection System Software

    International Nuclear Information System (INIS)

    Properties of programming languages, such as reliability, traceability, etc., play important roles in software development to improve safety. Several researches are proposed guidelines about programming to increase the dependability of software which is developed for safety critical systems. Misra-c is a widely accepted programming guidelines for the C language especially in the sector of vehicle industry. NUREG/CR-6463 helps engineers in nuclear industry develop software in nuclear power plant systems more dependably. FBD (Function Block Diagram), which is one of programming languages defined in IEC 61131-3 standard, is often used for software development of PLC (programmable logic controllers) in nuclear power plants. Software development for critical systems using FBD needs strict guidelines, because FBD is a general language and has easily mistakable elements. There are researches about guidelines for IEC 61131-3 programming languages. They, however, do not specify details about how to use languages. This paper proposes new guidelines for the FBD based on NUREG/CR-6463. The paper introduces a CASE (Computer-Aided Software Engineering) tool to check FBD programs with the new guidelines and shows availability with a case study using a FBD program in a reactor protection system. The paper is organized as follows

  7. A method for improvement of safety features of large fast breeder reactors. Numerical simulation of unprotected loss-of-flow accident in an LMFBR equipped with gas-expansion modules

    Energy Technology Data Exchange (ETDEWEB)

    Ishida, Masayoshi [Hitachi Engineering Co. Ltd., Ibaraki (Japan); Murakami, Tomoko; Kawashima, Katsuyuki; Watari, Yoshio; Nakao, Noboru; Miura, Masanori

    1995-04-01

    Numerical simulation of an unprotected loss-of-flow (ULOF) accident has been performed for a large liquid-metal-cooled fast breeder reactor (LMFBR) equipped with gas expansion modules (GEMs) in the radial periphery of the reactor core. The effectiveness of the GEMs in small fast reactors was demonstrated already in the passive safety testing in the Fast Flux Test Facility. According to neutronic calculations based on the transport theory, even in large reactors of electrical power 600 to 1,300 MW, the reactivity worth of GEMs, which replace one layer of radial blanket fuel subassemblies, ranges from -1.9$ to -1.4$, depending on the size of the core. A simulation of ULOF transient was performed with a 5.5s flow-halving time in a 600 MWe LMFBR equipped with GEMs of -1.9$ reactivity worth. The result showed that, if 10% of the rated core coolant flow by pony motors was available following the main pump coastdown, the GEM reactivity alone could bring the reactor subcritical and the predicted maximum coolant temperature was substantially lower than the sodium boiling point. The reactivity worth calculations, a modeling of gas expansion behavior, and ULOF simulation together with needs of further development for the GEM application are described. (author).

  8. Plutonium Worlds. Fast Breeders, Systems Analysis and Computer Simulation in the Age of Hypotheticality

    OpenAIRE

    Sebastian Vehlken

    2014-01-01

    This article examines the media history of one of the hallmark civil nuclear energy programs in Western Germany – the development of Liquid Metal Fast Breeder Reactor (LMFBR) technology. Promoted as a kind of perpetuum mobile of the Atomic Age, the "German Manhattan Project" not only imported big science thinking. In its context, nuclear technology was also put forth as an avantgarde of scientific inquiry, dealing with the most complex and critical technological endeavors. In the face of the ...

  9. Development Program of the Advanced HANARO Reactor in Korea

    International Nuclear Information System (INIS)

    The development program of an advanced HANARO (AHR) reactor started in Korea to keep abreast of the increasing future demand, from both home and abroad, for research activities. This paper provides a review of the status of research reactors in Korea, the operating experience of the HANARO, the design principles and preliminary features of an advanced HANARO reactor, and the specific strategy of an advanced HANARO reactor development program. The design principles were established in order to design a new multi-purpose research reactor that is safe, economically competitive and technically feasible. These include the adaptation of the HANARO design concept, its operating experience, a high ratio of flux to power, a high degree of safety, improved economic efficiency, improved operability and maintainability, increased space and expandability, and ALARA design optimization. The strategy of an advanced HANARO reactor development program considers items such as providing a digital advanced HANARO reactor in cyber space, a method for the improving the design quality and economy of research reactors by using Computer Integrated Engineering, and more effective advertising using diverse virtual reality. This development program will be useful for promoting the understanding of and interest in the operating HANARO as well as an advanced HANARO reactor under development in Korea. It will provide very useful information to a country that may need a research reactor in the near future for the promotion of public health, bio-technology, drug design, pharmacology, material processing, and the development of new materials. (author)

  10. Light Water Reactor Sustainability Program Integrated Program Plan

    Energy Technology Data Exchange (ETDEWEB)

    George Griffith; Robert Youngblood; Jeremy Busby; Bruce Hallbert; Cathy Barnard; Kathryn McCarthy

    2012-01-01

    Nuclear power has safely, reliably, and economically contributed almost 20% of electrical generation in the United States over the past two decades. It remains the single largest contributor (more than 70%) of non-greenhouse-gas-emitting electric power generation in the United States. Domestic demand for electrical energy is expected to experience a 31% growth from 2009 to 2035. At the same time, most of the currently operating nuclear power plants will begin reaching the end of their initial 20-year extension to their original 40-year operating license for a total of 60 years of operation. Figure E-1 shows projected nuclear energy contribution to the domestic generating capacity. If current operating nuclear power plants do not operate beyond 60 years, the total fraction of generated electrical energy from nuclear power will begin to decline - even with the expected addition of new nuclear generating capacity. The oldest commercial plants in the United States reached their 40th anniversary in 2009. The U.S. Department of Energy Office of Nuclear Energy's Research and Development Roadmap (Nuclear Energy Roadmap) organizes its activities around four objectives that ensure nuclear energy remains a compelling and viable energy option for the United States. The four objectives are as follows: (1) develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current reactors; (2) develop improvements in the affordability of new reactors to enable nuclear energy to help meet the Administration's energy security and climate change goals; (3) develop sustainable nuclear fuel cycles; and (4) understand and minimize the risks of nuclear proliferation and terrorism. The Light Water Reactor Sustainability (LWRS) Program is the primary programmatic activity that addresses Objective 1. This document summarizes the LWRS Program's plans.

  11. R and D activities of the liquid breeder blanket in Korea

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong Won, E-mail: dwlee@kaeri.re.kr [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Eo Hwak; Kim, Suk Kwon; Yoon, Jae Sung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Cho, Seungyon [National Fusion Research Institute, Daejeon (Korea, Republic of)

    2012-08-15

    Highlights: Black-Right-Pointing-Pointer MARS and GAMMA were developed for He coolant and liquid breeder analysis. Black-Right-Pointing-Pointer FMS/FMS and Be/FMS joining methods were developed and verified with high heat flux test. Black-Right-Pointing-Pointer High temperature and pressure nitrogen and He loops were constructed for heat transfer experiment for developed codes validation. Black-Right-Pointing-Pointer A PbLi breeder loop was constructed for components, MHD, and corrosion tests. Black-Right-Pointing-Pointer A chamber for tritium extraction with a gas-liquid contact method was constructed. - Abstract: A liquid breeder blanket has been developed in parallel with the International Thermonuclear Experimental Reactor (ITER) Test Blanket Module (TBM) program in Korea. The Korea Atomic Energy Research Institute (KAERI) has developed the common fields of a solid TBM such as design tools, structural material, fabrication methods, and He cooling technology to support this concept for the ITER. Also, other fields such as a liquid breeder technology and tritium extraction have been developed from the designed liquid TBM. For design tools, system codes for safety analysis such as Multi-dimensional Analysis of Reactor Safety (MARS) and GAs Multi-component Mixture Analysis (GAMMA) were developed for He coolant and liquid breeder. For the fabrication methods, Ferritic Martensitic Steel (FMS) to FMS and Be to FMS joinings with a Hot Isostatic Pressing (HIP) were developed and verified with a high heat flux test of up to 0.5-1.0 MW/m{sup 2}. Moreover, three mockups were successfully fabricated and a 10-channel prototype is being fabricated to make a rectangular channel FW. For the integrity of the joining, two high heat flux test facilities were constructed, and one using an electron beam has been constructed. With the 6 MPa nitrogen loop, a basic heat transfer experiment for code validation was performed. From the verification of the components such as preheater and

  12. Status and prospects of thermal breeders and their effect on fuel utilization

    International Nuclear Information System (INIS)

    The report evaluates the extent to which thermal breeders and near-breeders might complement fast breeders or serve as an alternative in solving the long-term nuclear fuel supply problem. It considers in a general way issues such as proliferation, safety, environmental impacts, economics, power plant availability and fuel cycle versatility in order to determine whether thermal breeder reactors offer advantages or disadvantages with respect to such issues

  13. Participation in the US Department of Energy Reactor Sharing Program

    International Nuclear Information System (INIS)

    The objective of the DOE supported Reactor Sharing Program is to increase the availability of university nuclear reactor facilities to non-reactor-owning educational institutions. The educational and research programs of these user institutions is enhanced by the use of the nuclear facilities. Several methods have been used by the UVA Reactor Facility to achieve this objective. First, many college and secondary school groups toured the Reactor Facility and viewed the UVAR reactor and associated experimental facilities. Second, advanced undergraduate and graduate classes from area colleges and universities visited the facility to perform experiments in nuclear engineering and physics which would not be possible at the user institution. Third, irradiation and analysis services at the Facility have been made available for research by faculty and students from user institutions. Fourth, some institutions have received activated material from UVA for use at their institutions. These areas are discussed further in the report

  14. Light Water Reactor Sustainability Program Integrated Program Plan

    Energy Technology Data Exchange (ETDEWEB)

    Kathryn McCarthy; Jeremy Busby; Bruce Hallbert; Shannon Bragg-Sitton; Curtis Smith; Cathy Barnard

    2013-04-01

    Nuclear power has safely, reliably, and economically contributed almost 20% of electrical generation in the United States over the past two decades. It remains the single largest contributor (more than 70%) of non-greenhouse-gas-emitting electric power generation in the United States. Domestic demand for electrical energy is expected to experience a 31% growth from 2009 to 2035. At the same time, most of the currently operating nuclear power plants will begin reaching the end of their initial 20-year extension to their original 40-year operating license for a total of 60 years of operation. Figure E-1 shows projected nuclear energy contribution to the domestic generating capacity. If current operating nuclear power plants do not operate beyond 60 years, the total fraction of generated electrical energy from nuclear power will begin to decline—even with the expected addition of new nuclear generating capacity. The oldest commercial plants in the United States reached their 40th anniversary in 2009. The U.S. Department of Energy Office of Nuclear Energy’s Research and Development Roadmap (Nuclear Energy Roadmap) organizes its activities around four objectives that ensure nuclear energy remains a compelling and viable energy option for the United States. The four objectives are as follows: (1) develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current reactors; (2) develop improvements in the affordability of new reactors to enable nuclear energy to help meet the Administration’s energy security and climate change goals; (3) develop sustainable nuclear fuel cycles; and (4) understand and minimize the risks of nuclear proliferation and terrorism. The Light Water Reactor Sustainability (LWRS) Program is the primary programmatic activity that addresses Objective 1. This document summarizes the LWRS Program’s plans.

  15. Light Water Reactor Sustainability Program Integrated Program Plan

    Energy Technology Data Exchange (ETDEWEB)

    McCarthy, Kathryn A. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Busby, Jeremy [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hallbert, Bruce [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bragg-Sitton, Shannon [Idaho National Lab. (INL), Idaho Falls, ID (United States); Smith, Curtis [Idaho National Lab. (INL), Idaho Falls, ID (United States); Barnard, Cathy [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-04-01

    Nuclear power has safely, reliably, and economically contributed almost 20% of electrical generation in the United States over the past two decades. It remains the single largest contributor (more than 70%) of non-greenhouse-gas-emitting electric power generation in the United States. Domestic demand for electrical energy is expected to experience a 31% growth from 2009 to 2035. At the same time, most of the currently operating nuclear power plants will begin reaching the end of their initial 20-year extension to their original 40-year operating license for a total of 60 years of operation. Figure E-1 shows projected nuclear energy contribution to the domestic generating capacity. If current operating nuclear power plants do not operate beyond 60 years, the total fraction of generated electrical energy from nuclear power will begin to decline—even with the expected addition of new nuclear generating capacity. The oldest commercial plants in the United States reached their 40th anniversary in 2009. The U.S. Department of Energy Office of Nuclear Energy’s Research and Development Roadmap (Nuclear Energy Roadmap) organizes its activities around four objectives that ensure nuclear energy remains a compelling and viable energy option for the United States. The four objectives are as follows: (1) develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current reactors; (2) develop improvements in the affordability of new reactors to enable nuclear energy to help meet the Administration’s energy security and climate change goals; (3) develop sustainable nuclear fuel cycles; and (4) understand and minimize the risks of nuclear proliferation and terrorism. The Light Water Reactor Sustainability (LWRS) Program is the primary programmatic activity that addresses Objective 1. This document summarizes the LWRS Program’s plans.

  16. The search for advanced remote technology in fast reactor reprocessing

    International Nuclear Information System (INIS)

    Research and development in fast reactor reprocessing has been under way ∼ 20 yr in several countries. During the past decade, France and the United Kingdom have developed active programs in breeder reprocessing. Actual fuels from their demonstration reactors have been reprocessed in small-scale facilities. Early US work in breeder reprocessing was carried out at the Experimental Breeder Reactor II (EBR-II) facilities with the early metal fuels, and interest has renewed recently in metal fuels. A major, comprehensive program, focused on oxide fuels, has been carried out in the Consolidated Fuel Reprocessing Program (CFRP) at the Oak Ridge National Laboratory (ORNL) since 1974. The Federal Republic of Germany (FRG) and Japan have also carried out development programs in breeder reprocessing, and Japan appears committed to major demonstration of breeder reactors and their fuel cycles. While much of the effort in these programs addressed process chemistry and process hardware, a significant element of many of these programs, particularly the CFRP, has been on advancements in facility concepts and remote maintenance features. This paper focuses on the search for improved facility concepts and better maintenance systems in the CFRP, and, in turn, on how developments at ORNL have influenced the technology elsewhere

  17. Research and development status of ceramic breeder materials

    International Nuclear Information System (INIS)

    The breeding blanket is a key component of the fusion reactor because it directly involves tritium breeding and energy extraction, both of which are critical to development of fusion power. The lithium ceramics continue to show promise as candidate breeder materials. This promise was also recognized by the International Thermonuclear Experimental Reactor (ITER) design team in its selection of ceramics as the first option breeder material. Blanket design studies have indicated areas in the properties data base that need further investigation. Current studies are focusing on issues such as tritium release behavior at high burnup, changes in thermophysical properties with burnup, compatibility between ceramic breeder and beryllium multiplier, and phase changes with burnup. Laboratory and in-reactor tests are underway, some as part of an international collaboration for development of ceramic breeder materials. 36 refs

  18. Fabrication, properties, and tritium recovery from solid breeder materials

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, C.E. (Argonne National Lab., IL (USA)); Kondo, T. (Japan Atomic Energy Research Inst., Tokyo (Japan)); Roux, N. (CEA Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France)); Tanaka, S. (Tokyo Univ. (Japan)); Vollath, D. (Kernforschungszentrum Karlsruhe GmbH (Germany, F.R.))

    1991-01-01

    The breeding blanket is a key component of the fusion reactor because it directly involves tritium breeding and energy extraction, both of which are critical to development of fusion power. The lithium ceramics continue to show promise as candidate breeder materials. This promise was recognized by the International Thermonuclear Experimental Reactor (ITER) design team in its selection of ceramics as the first option for the ITER breeder material. Blanket design studies have indicated properties in the candidate materials data base that need further investigation. Current studies are focusing on tritium release behavior at high burnup, changes in thermophysical properties with burnup, compatibility between the ceramic breeder and beryllium multiplier, and phase changes with burnup. Laboratory and in-reactor tests, some as part of an international collaboration for development of ceramic breeder materials, are underway. 133 refs., 1 fig.

  19. Special Analysis for the Disposal of the Idaho National Laboratory Unirradiated Light Water Breeder Reactor Rods and Pellets Waste Stream at the Area 5 Radioactive Waste Management Site, Nevada National Security Site, Nye County, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Shott, Gregory [NSTec

    2014-08-31

    The purpose of this special analysis (SA) is to determine if the Idaho National Laboratory (INL) Unirradiated Light Water Breeder Reactor (LWBR) Rods and Pellets waste stream (INEL103597TR2, Revision 2) is suitable for disposal by shallow land burial (SLB) at the Area 5 Radioactive Waste Management Site (RWMS). The INL Unirradiated LWBR Rods and Pellets waste stream consists of 24 containers with unirradiated fabricated rods and pellets composed of uranium oxide (UO2) and thorium oxide (ThO2) fuel in zirconium cladding. The INL Unirradiated LWBR Rods and Pellets waste stream requires an SA because the 229Th, 230Th, 232U, 233U, and 234U activity concentrations exceed the Nevada National Security Site (NNSS) Waste Acceptance Criteria (WAC) Action Levels.

  20. Results and recommendations from the reactor chemistry and corrosion tasks of the reactor materials program

    International Nuclear Information System (INIS)

    Within the general context of extended service life, the Reactor Materials Program was initiated in 1984. This comprehensive program addressed material performance in SRS reactor tanks and the primary coolant or Process Water System (PWS) piping. Three of the eleven tasks concerned moderator quality and corrosion mitigation. Definition and control of the stainless steel aqueous environment is a key factor in corrosion mitigation. The Reactor Materials Program systematically investigated the SRS environment and its effect on crack initiation and propagation in stainless steel, with the objective of improving this environment. The purpose of this report is to summarize the contributions of Tasks 6, 7 and 10 of the Reactor Materials Program to the understanding and control of moderator quality and its relationship to mitigation of stress corrosion cracking

  1. Accelerator breeder with uranium, thorium target

    International Nuclear Information System (INIS)

    An accelerator breeder, that uses a low-enriched fuel as the target material, can produce substantial amounts of fissile material and electric power. A study of H2O- and D2O-cooled, UO2, U, (depleted U), or thorium indicates that U-metal fuel produces a good fissile production rate and electrical power of about 60% higher than UO2 fuel. Thorium fuel has the same order of magnitude as UO2 fuel for fissile-fuel production, but the generating electric power is substantially lower than in a UO2 reactor. Enriched UO2 fuel increases the generating electric power but not the fissile-material production rate. The Na-cooled breeder target has many advantages over the H2O-cooled breeder target

  2. Decentralization of operating reactor licensing reviews: NRR Pilot Program

    International Nuclear Information System (INIS)

    This report, which has incorporated comments received from the Commission and ACRS, describes the program for decentralization of selected operating reactor licensing technical review activities. The 2-year pilot program will be reviewed to verify that safety is enhanced as anticipated by the incorporation of prescribed management techniques and application of resources. If the program fails to operate as designed, it will be terminated

  3. Reactor Safety Research Programs Quarterly Report January - March 1980

    Energy Technology Data Exchange (ETDEWEB)

    Hagen, C. M

    1980-10-01

    This document summarizes the work performed by Pacific Northwest Laboratory from January 1 through March 31, 1980, for the Division of Reactor Safety Research within the Nuclear Regulatory Commission. Evaluation of nondestructive examination (NDE) techniques and instrumentation are reported; areas of investigation include demonstrating the feasibilty of determining structural graphite strength, evaluating the feasibilty of detecting and analyzing flaw growth in reactor pressure boundary systems, examining NDE reliability and probabilistic fracture mechanics, and assessing the remaining integrity of pressurized water reactor steam generator tubes where serviceinduced degradation has been indicated. Test assemblies and analytical support are being provided for experimental programs at other facilities. These programs include the loss-of-coolant accident simulation tests at the NRU reactor, Chalk River, Canada; the fuel rod deformation and post-accident coolability tests for the ESSOR Test Reactor Program, Ispra, Italy; the blowdown and reflood tests in the test facility at Cadarache, France; the instrumented fuel assembly irradiation program at Halden, Norway; and the experimental programs at the Power Burst Facility, Idaho National Engineering Laboratory. These programs will provide data for computer modeling of reactor system and fuel performance during various abnormal operating conditions.

  4. Reactor Safety Research Programs Quarterly Report July - September 1981

    Energy Technology Data Exchange (ETDEWEB)

    Edler, S. K.

    1982-01-01

    This document summarizes the work performed by Pacific Northwest laboratory (PNL) from July 1 through September 30, 1981, for the Division of Accident Evaluation, U.S. Nuclear Regulatory Commission (NRC). Evaluations of nondestructive examination (NDE) techniques and instrumentation are reported; areas of investigation include demonstrating the feasibility of determining the strength of structural graphite, evaluating the feasibility of detecting and analyzing flaw growth in reactor pressure boundary systems, examining NDE reliability and probabilistic fracture mechanics, and assessing the integrity of pressurized water reactor (PWR} steam generator tubes where service-induced degradation has been indicated. Experimental data and analytical models are being provided to aid in decision-making regarding pipe-to-pipe impacts following postulated breaks in high-energy fluid system piping. Core thermal models are being developed to provide better digital codes to compute the behavior of full-scale reactor systems under postulated accident conditions. Fuel assemblies and analytical support are being provided for experimental programs at other facilities. These programs include loss-of-coolant accident (LOCA) simulation tests at the NRU reactor, Chalk River, Canada; fuel rod deformation, severe fuel damage, and postaccident coolability tests for the ESSOR reactor Super Sara Test Program, lspra, Italy; the instrumented fuel assembly irradiation program at Halden, Norway; and experimental programs at the Power Burst Facility, Idaho National Engineering Laboratory (INEL), Idaho Falls, Idaho. These programs will provide data for computer modeling of reactor system and fuel performance during various abnormal operating conditions.

  5. Reactor Safety Research Programs Quarterly Report October - December 1981

    Energy Technology Data Exchange (ETDEWEB)

    Edler, S. K.

    1982-03-01

    This document summarizes the work performed by Pacific Northwest laboratory (PNL) from October 1 through December 31, 1981, for the Division of Accident Evaluation, U.S. Nuclear Regulatory Commission (NRC). Evaluations of nondestructive examination (NDE) techniques and instrumentation are reported; areas of investigation include demonstrating the feasibility of determining the strength of structural graphite, evaluating the feasibility of detecting and analyzing flaw growth in reactor pressure boundary systems, examining NDE reliability and probabilistic fracture mechanics, and assessing the integrity of pressurized water reactor (PWR) steam generator tubes where serviceinduced degradation has been indicated. Experimental data and analytical models are being provided to aid in decision-making regarding pipe-to-pipe impacts following postulated breaks in high-energy fluid system piping. Core thermal models are being developed to provide better digital codes to compute the behavior of full-scale reactor systems under postulated accident conditions. Fuel assemblies and analytical support are being provided for experimental programs at other facilities. These programs include loss-of-coolant accident (LOCA) simulation tests at the NRU reactor, Chalk River, Canada; fuel rod deformation, severe fuel damage, and post accident coolability tests for the ESSOR reactor Super Sara Test Program, lspra, Italy; the instrumented fuel assembly irradiation program at Halden, Norway; and experimental programs at the Power Burst Facility, Idaho National Engineering Laboratory (INEL), Idaho Falls, Idaho. These programs will provide data for computer modeling of reactor system and fuel performance during various abnormal operating conditions.

  6. OSU Reactor Sharing Program FY 1995 annual report

    International Nuclear Information System (INIS)

    This is the annual report of the activities supported under the Oregon State University Reactor Sharing Program, award number DE-FG06-NE38137. The beginning date for the award was September, 30, 1995 and the end date was September 29, 1996. Work conducted under this award is internally administered at the Radiation Center through a project tasking system. This allows for excellent quality control for the work which is performed from the point of initial contact, through the reactor application, project report generation and financial accounting. For the current fiscal year, FY95, the total cost of the reactor sharing program, including Radiation Center contributions, was $66,323.20 of which $40,000.00 was supplied by the DOE Reactor Sharing Program. The details of individual project costs is given in Table 1. The work performed for the individual projects are described in the brief work descriptions given in Table 2

  7. Gas Reactor International Cooperative Program: German Pebble Bed Reactor Technology review update

    International Nuclear Information System (INIS)

    This report provides a review of the German pebble bed reactor technology, and updates the information provided in the Gas Reactor International Cooperative Program Interim Report COO-4057-6, German Pebble Bed Reactor Design and Technology Review, dated September 1978. Most of the updated information is for the PNP-500 and the HHT-Prototype plants. The PNP-500 is a 500 MW(t) multi-purpose demonstration plant for coal conversion applications. The HHT-Prototype is a 1640 MWt reactor designed to produce 675 MWe of electricity using a direct cycle gas turbine. The report provides a description and evaluation of the overall plant and the nuclear reactor for both the PNP-500 and HHT-Prototype. A description and evaluation of the primary system components is presented for the process heat and gas turbine applications

  8. Safety program considerations for space nuclear reactor systems

    Energy Technology Data Exchange (ETDEWEB)

    Cropp, L.O.

    1984-08-01

    This report discusses the necessity for in-depth safety program planning for space nuclear reactor systems. The objectives of the safety program and a proposed task structure is presented for meeting those objectives. A proposed working relationship between the design and independent safety groups is suggested. Examples of safety-related design philosophies are given.

  9. Safety program considerations for space nuclear reactor systems

    International Nuclear Information System (INIS)

    This report discusses the necessity for in-depth safety program planning for space nuclear reactor systems. The objectives of the safety program and a proposed task structure is presented for meeting those objectives. A proposed working relationship between the design and independent safety groups is suggested. Examples of safety-related design philosophies are given

  10. Cooperative and concentrated breeder development in Europe

    Energy Technology Data Exchange (ETDEWEB)

    Hueper, R.

    The agreement of 1984 on cooperation for the fast breeder development, concluded by West Germany and France, Great Britain, Belgium and Italy, created the basis for abandoning the 'autarky' of national development efforts, which since then have been combined into a joint demonstration project. This European Fast Reactor, EFR, is in the phase of preparatory planning and is intended to replace the originally planned three installations SNR-2, SPX-2, and CDFR. There still are financing problems to be solved, and the conditions of further participation of Italy (and the Netherlands) are awaiting final decisions. The joint European experience in breeder development relies on operating results of more than 12 power reactors in the world, and the SNR-300 is expected to contribute a wealth of new experience after its commissioning.

  11. Fuel and target programs for the transmutation at Phenix and other reactors; Programmes combustibles et cibles pour la transmutation dans Phenix et autres reacteurs

    Energy Technology Data Exchange (ETDEWEB)

    Gaillard-Groleas, G

    2002-07-01

    The fuels and targets program for transmutation, performed in the framework of the axis 1 of the December 1991 law about the researches on the management of long-lived radioactive wastes, is in perfect consistency with the transmutation scenario studies carried out in the same framework. These studies put forward the advantage of fast breeder reactors (FBR) in the incineration of minor actinides and long-lived fission products. The program includes exploratory and technological demonstration studies covering the different design options. It aims at enhancing our knowledge of the behaviour of materials under irradiation and at ensuring the mastery of processes. The goals of the different experiments foreseen at Phenix reactor are presented. The main goal is to supply a set of results allowing to precise the conditions of the technical feasibility of minor actinides and long-lived fission products incineration in FBRs. (J.S.)

  12. Molten salt converter reactors: from DMSR to SmAHTR

    International Nuclear Information System (INIS)

    Molten salt reactors were developed extensively from the 1950s to 1970s as a thermal breeder alternative on the Thorium-233U cycle. Simplified designs running as fluid fuel converters without salt processing as well as TRISO fueled, salt cooled reactors both hold much promise as potential small modular reactors and as larger base load producers. A background will be presented along with the most likely routes forward for a Canadian development program. (author)

  13. Assessment of light water reactor accident management programs and experience

    International Nuclear Information System (INIS)

    The objective of this report is to provide an assessment of the current light water reactor experience regarding accident management programs and associated technology developments. This assessment for light water reactor (LWR) designs is provided as a resource and reference for the development of accident management capabilities for the production reactors at the Savannah River Site. The specific objectives of this assessment are as follows: 1. Perform a review of the NRC, utility, and industry (NUMARC, EPRI) accident management programs and implementation experience. 2. Provide an assessment of the problems and opportunities in developing an accident management program in conjunction or following the Individual Plant Examination process. 3. Review current NRC, utility, and industry technological developments in the areas of computational tools, severe accident predictive tools, diagnostic aids, and severe accident training and simulation

  14. Assessment of light water reactor accident management programs and experience

    Energy Technology Data Exchange (ETDEWEB)

    Hammersley, R.J. [Fauske and Associates, Inc., Burr Ridge, IL (United States)

    1992-03-01

    The objective of this report is to provide an assessment of the current light water reactor experience regarding accident management programs and associated technology developments. This assessment for light water reactor (LWR) designs is provided as a resource and reference for the development of accident management capabilities for the production reactors at the Savannah River Site. The specific objectives of this assessment are as follows: 1. Perform a review of the NRC, utility, and industry (NUMARC, EPRI) accident management programs and implementation experience. 2. Provide an assessment of the problems and opportunities in developing an accident management program in conjunction or following the Individual Plant Examination process. 3. Review current NRC, utility, and industry technological developments in the areas of computational tools, severe accident predictive tools, diagnostic aids, and severe accident training and simulation.

  15. Plutonium Worlds. Fast Breeders, Systems Analysis and Computer Simulation in the Age of Hypotheticality

    Directory of Open Access Journals (Sweden)

    Sebastian Vehlken

    2014-09-01

    Full Text Available This article examines the media history of one of the hallmark civil nuclear energy programs in Western Germany – the development of Liquid Metal Fast Breeder Reactor (LMFBR technology. Promoted as a kind of perpetuum mobile of the Atomic Age, the "German Manhattan Project" not only imported big science thinking. In its context, nuclear technology was also put forth as an avantgarde of scientific inquiry, dealing with the most complex and critical technological endeavors. In the face of the risks of nuclear technology, German physicist Wolf Häfele thus announced a novel epistemology of "hypotheticality". In a context where traditional experimental engineering strategies became inappropiate, he called for the application of advanced media technologies: Computer Simulations (CS and Systems Analysis (SA generated computerized spaces for the production of knowledge. In the course of the German Fast Breeder program, such methods had a twofold impact. One the one hand, Häfele emphazised – as the "father of the German Fast Breeder" – the utilization of CS for the actual planning and construction of the novel reactor type. On the other, namely as the director of the department of Energy Systems at the International Institute for Applied Systems Analysis (IIASA, Häfele advised SA-based projections of energy consumption. These computerized scenarios provided the rationale for the conception of Fast Breeder programs as viable and necessary alternative energy sources in the first place. By focusing on the role of the involved CS techniques, the paper thus investigates the intertwined systems thinking of nuclear facilities’s planning and construction and the design of large-scale energy consumption and production scenarios in the 1970s and 1980s, as well as their conceptual afterlives in our contemporary era of computer simulation.

  16. TRIGA Mark-III reactor dismantling program

    International Nuclear Information System (INIS)

    The activation assessment of the main parts of the TRIGA Mark-III (KRR-2) was estimated to effectively dismantle the activated and contaminated areas. All of the method and the order for decommissioning the KRR-2 have been chosen as a result of the examination of the physical structure and radiological conditions of the reactor component. These decommissioning methods and orders were reviewed as part of the Hazard and Operability (HAZOP) studies for the project. Radiological assessment is also done to protect the workers and the environment from the dismantling work. License documents were submitted to the Ministry of Science and Technology (MOST) at the end of 1998. Practical work of the D and D will start at the end of 1999 once the government issues the license. Radiation protection plan was also set up to control the workers and environment. This paper summarized the main lines of those studies. (author)

  17. Proceedings of the fifteenth international workshop on ceramic breeder blanket interactions

    International Nuclear Information System (INIS)

    This report is the Proceedings of 'the Fifteenth International Workshop on Ceramic Breeder Blanket Interactions' which was held as a workshop on ceramic breeders Under the IEA Implementing Agreement on the Nuclear Technology of Fusion Reactors. This workshop was held in Sapporo, Japan on 3-4, Sept. 2009. Twenty six participants from EU, Japan, India, Russia and USA attended the workshop. The scope of the workshop included 1) evolutions in ceramic breeder blanket design, 2) progress in ceramic breeder material development, 3) irradiation testing, 4) breeder material properties, 5) out-of-pile pebble bed experiment, 6) modeling of the thermal, mechanical and tritium transfer behavior of pebble beds and 7) interfacing issues of solid breeder blanket development. By this workshop, advance of key technologies for solid breeder blanket development was shared among the participants. Also, desired direction of further investigation and development was recognized. The 20 of the presented papers are indexed individually. (J.P.N.)

  18. In-core fuel management programs for nuclear power reactors

    International Nuclear Information System (INIS)

    In response to the interest shown by Member States, the IAEA organized a co-ordinated research programme to develop and make available in the open domain a set of programs to perform in-core fuel management calculations. This report summarizes the work performed in the context of the CRP. As a result of this programme, complete in-core fuel management packages for three types of reactors, namely PWR's, BWR's and PHWR are now available from the NEA Data Bank. For some reactor types, these program packages are available with three levels of sophistication ranging from simple methods for educational purposes to more comprehensive methods that can be used for reactor design and operation. In addition some operating data have been compiled to allow code validation. (author)

  19. Fast breeders role in the energy supply of the EC

    International Nuclear Information System (INIS)

    The investigation summarized in this article was initiated by a work team of the International Society of Power Generators (UNIPEDE) and the EC-commission. The first part presents the results of the possible introduction of fast breeder reactors in the EC for power generation and describes its effects on the demand for natural uranium. The second part describes the present development level of reprocessing of breeder reactor fuel, a part of the fuel cycle which is of very special importance. With the assumption of a rather undisturbed utilization of nuclear energy the investigation comes to the result that the development of the fast breeders and their fuel cycle in the EC must be promoted in any case. And, in the future, the available means should be used for a balanced development of both the reactor system and the fuel cycle. (orig.)

  20. Laser fusion driven breeder design study. Final report

    International Nuclear Information System (INIS)

    The results of the Laser Fusion Breeder Design Study are given. This information primarily relates to the conceptual design of an inertial confinement fusion (ICF) breeder reactor (or fusion-fission hybrid) based upon the HYLIFE liquid metal wall protection concept developed at Lawrence Livermore National Laboratory. The blanket design for this breeder is optimized to both reduce fissions and maximize the production of fissile fuel for subsequent use in conventional light water reactors (LWRs). When the suppressed fission blanket is compared with its fast fission counterparts, a minimal fission rate in the blanket results in a unique reactor safety advantage for this concept with respect to reduced radioactive inventory and reduced fission product decay afterheat in the event of a loss-of-coolant-accident

  1. A contribution to the analysis of the thermal behaviour of Fast Breeder fuel rods with UO{sub 2}-PuO{sub 2} fuel; Contribucion al analisis del comportamiento termico de las barras combustibles de UO{sub 2}-PuO{sub 2} de los reactores rapidos

    Energy Technology Data Exchange (ETDEWEB)

    Lopez Jimenez, J.; Elbel, H.

    1977-07-01

    The fuel of Fast Breeder Reactors which consists of Uranium and Plutonium dioxide is mainly characterized by the amount and distribution of void volume and Plutonium and the amount of oxygen. Irradiation experiments carried out with this fuel have shown that initial structure of the fuel pellet is subjected to large changes during operation. These are consequences of the radial and axial temperature gradients within the fuel rods. (Author) 54 refs.

  2. Recent progress of Gas Fast Reactor program

    International Nuclear Information System (INIS)

    The GFR is considered by the French Atomic Energy Commission as a promising concept which combines the benefits of fast spectrum and high temperature, using helium as coolant. He properties are interesting with respect to safety: it is single phase (no threshold effect due to phase changing), chemically inert, and non toxic. It affords an optical transparency allowing potential improvements in temperature measurement, management for dismantling, and in-service-inspection. The voiding effect is limited, less than 1$, providing quasi- decoupling of the reactor physics from the state of the coolant. Nevertheless, Helium is a poor coolant, so that the GFR viability includes development of a refractory and dense fuel, and robust management of accidental transients, especially cooling accidents. GFR feasibility is essentially linked to three demonstrations: the feasibility (fabrication, thermo-mechanical behaviour) of a refractory fuel; the safety architecture with appropriate systems for the prevention and a robust mitigation of accidental scenarios (especially depressurization); economic competitiveness. The first one includes an experimental activity at the laboratory scale: completion of the results is expected by 2012-2015. The next step afterward will be the design, construction and the operation of a 50-100 MWth experimental reactor, the Allegro project (former ETDR), possibly as a European Joint Undertaking. The full paper will recall the 2007 design choices and it will give an overview of the progress performed so far regarding the safety architecture and the safety evaluation. The 2007 reference fuel technology is a ceramic plate type fuel element. It combines a high enough core power density (minimization of the Pu inventory), plutonium and minor actinides recycling capabilities. Innovative to many aspects, the fuel element is a key issue in the GFR feasibility. It is supported already by a significant R and D effort also applicable to a pin concept that is

  3. Integral Fast Reactor Program. Annual progress report, FY 1992

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Y.I.; Walters, L.C.; Laidler, J.J.; Pedersen, D.R.; Wade, D.C.; Lineberry, M.J.

    1993-06-01

    This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1992. Technical accomplishments are presented in the following areas of the IFR technology development activities: (1) metal fuel performance, (2) pyroprocess development, (3) safety experiments and analyses, (4) core design development, (5) fuel cycle demonstration, and (6) LMR technology R&D.

  4. Integral Fast Reactor Program annual progress report, FY 1994

    International Nuclear Information System (INIS)

    This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1994. Technical accomplishments are presented in the following areas of the IFR technology development activities: metal fuel performance; pyroprocess development; safety experiments and analyses; core design development; fuel cycle demonstration; and LMR technology R ampersand D

  5. Integral Fast Reactor Program annual progress report, FY 1991

    International Nuclear Information System (INIS)

    This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1991. Technical accomplishments are presented in the following areas of the IFR technology development activities: (1) metal fuel performance, (2) pyroprocess development, (3) safety experiments and analyses, (4) core design development, (5) fuel cycle demonstration, and (6) LMR technology R ampersand D

  6. Integral Fast Reactor Program. Annual progress report, FY 1993

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Y.I.; Walters, L.C.; Laidler, J.J.; Pedersen, D.R.; Wade, D.C.; Lineberry, M.J.

    1994-10-01

    This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1993. Technical accomplishments are presented in the following areas of the IFR technology development activities: (1) metal fuel performance, (2) pyroprocess development, (3) safety experiments and analyses, (4) core design development, (5) fuel cycle demonstration, and (6) LMR technology R and D.

  7. Integral Fast Reactor Program annual progress report, FY 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-06-01

    This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1991. Technical accomplishments are presented in the following areas of the IFR technology development activities: (1) metal fuel performance, (2) pyroprocess development, (3) safety experiments and analyses, (4) core design development, (5) fuel cycle demonstration, and (6) LMR technology R D.

  8. Integral Fast Reactor Program annual progress report, FY 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-06-01

    This report summarizes highlights of the technical progress made in the Integral Fast Reactor (IFR) Program in FY 1991. Technical accomplishments are presented in the following areas of the IFR technology development activities: (1) metal fuel performance, (2) pyroprocess development, (3) safety experiments and analyses, (4) core design development, (5) fuel cycle demonstration, and (6) LMR technology R&D.

  9. Safety evaluation report related to the construction of the Clinch River Breeder Reactor Plant. Docket No. 50-537. Suppl. 1

    International Nuclear Information System (INIS)

    Since the preparation of the Safety Evaluation Report the Advisory Committee on Reactor Safeguards considered the Clinch River construction permit license application at its 276th meeting and subsequently issued a favorable report, dated April 19, 1983 to the Commission (See Appendix I of this report). Additional documents associated with the application have been reviewed and a number of meetings have been held with the applicants. These events and documents are identified in Appendix E to this supplement. This supplement, SSER-1, to the Safety Evaluation Report, provides an evaluation of additional information received from the applicants since preparation of the SER regarding previously identified outstanding review items, and our response to the comments made by the Advisory Committee on Reactor Safeguards in its report

  10. Study of some electrochemical properties of uranium in a molten fluoride medium. Application to the determination of the U(IV)/U(III) ratio in the fuel of a fused salt breeder reactor

    International Nuclear Information System (INIS)

    The aim of this work is to check the possibility of determining the U(IV)/U(III) ratio by electrochemical techniques in the fused LiF-BeF2-ThF4 mixture, solvent of a fused salt breeder reactor. The electrochemical properties of uranium systems were studied. The electrochemical reduction of U(IV) in LiF-BeF2-ThF4 at 615 0C was studied by linear and cyclic potential variation voltamperometry, constant current voltamperometry and pulse voltamperometry (normal and derived mode). The results obtained at a molybdenum electrode show two successive electron transfers. The formation of U-Mo alloy is observed. The oxidation of U(IV) was observed at a vitreous carbon electrode. The results show that the uranium V formed is unstable, their interpretation suggesting that U(IV) dismutes into U(IV) and probably into gaseous UF6. In view of these results it was possible to determine the U(IV)/U(III) ratio by the use of the above electrochemical techniques

  11. Tridimensional ultrasonic images analysis for the in service inspection of fast breeder reactors; Analyse d'images tridimensionnelles ultrasonores pour l'inspection en service des reacteurs a neutrons rapides

    Energy Technology Data Exchange (ETDEWEB)

    Dancre, M

    1999-11-01

    Tridimensional image analysis provides a set of methods for the intelligent extraction of information in order to visualize, recognize or inspect objects in volumetric images. In this field of research, we are interested in algorithmic and methodological aspects to extract surface visual information embedded in volume ultrasonic images. The aim is to help a non-acoustician operator, possibly the system itself, to inspect surfaces of vessel and internals in Fast Breeder Reactors (FBR). Those surfaces are immersed in liquid metal, what justifies the ultrasonic technology choice. We expose firstly a state of the art on the visualization of volume ultrasonic images, the methods of noise analysis, the geometrical modelling for surface analysis and finally curves and surfaces matching. These four points are then inserted in a global analysis strategy that relies on an acoustical analysis (echoes recognition), an object analysis (object recognition and reconstruction) and a surface analysis (surface defects detection). Few literature can be found on ultrasonic echoes recognition through image analysis. We suggest an original method that can be generalized to all images with structured and non-structured noise. From a technical point of view, this methodology applied to echoes recognition turns out to be a cooperative approach between morphological mathematics and snakes (active contours). An entropy maximization technique is required for volumetric data binarization. (author)

  12. Analysis of thorium and uranium fuel cycles in an iso-breeder lead fast reactor using extended-EQL3D procedure

    International Nuclear Information System (INIS)

    Highlights: ► Extension of EQL3D procedure to calculate radio-toxicity and decay heat. ► Characterization of uranium- and thorium-fueled LFR from BOL to equilibrium. ► Safety improvements for a LFR in a closed thorium cycle. ► Advantages of thorium-fueled LFR in terms of decay heat and radio-toxicity generation. ► Safety, decay heat and radio-toxicity concerns for a Th–Pu beginning-of-life core. - Abstract: Use of thorium in fast reactors has typically been considered as a secondary option, mainly thanks to a possible self-sustaining thorium cycle already in thermal reactors and due to the limited breeding capabilities compared to U–Pu in the fast neutron energy range. In recent years nuclear waste management has become more important, and the thorium option has been reconsidered for the claimed potential to burn transuranic waste and the lower build-up of hazardous isotopes in a closed cycle. To ascertain these claims and their limitations, the fuel cycle isotopic inventory, and associated waste radio-toxicity and decay heat, should be quantified and compared to the case of the uranium cycle using realistic core configurations, with complete recycle of all the actinides. Since the transition from uranium to thorium fuel cycles will likely involve a transuranic burning phase, this transition and the challenges that the evolving fuel actinide composition presents, for instance on reactor feedback parameters, should also be analyzed. In the present paper, these issues are investigated based on core physics analysis of the Lead-cooled Fast Reactor ELSY, performed with the fast reactor ERANOS code and the EQL3D procedure allowing full-core characterization of the equilibrium cycle and the transition cycles. In order to compute radio-toxicity and decay heat, EQL3D has been extended by developing a new module, which has been assessed against ORIGEN-S and is presented here. The capability of the EQL3D procedure to treat full-core 3D geometries allowed to

  13. Technology of steam generators for gas-cooled reactors. Proceedings of a specialists' meeting

    International Nuclear Information System (INIS)

    The activity of the IAEA in the field of the technology of gas-cooled reactors was formalized by formation of an International Working Group on Gas-Cooled Reactors (IWGCR). The gas cooled reactor program considered by the IWGCR includes carbon-dioxide-cooled thermal reactors, helium cooled thermal high temperature reactors for power generation and for process heat applications and gas-cooled fast breeder reactors. This report covers the papers dealing with operating experience, steam generators for next generation of gas-cooled reactors, material development and corrosion problems, and thermohydraulics

  14. Fast reactor programme in India

    Indian Academy of Sciences (India)

    P Chellapandi; P R Vasudeva Rao; Prabhat Kumar

    2015-09-01

    Role of fast breeder reactor (FBR) in the Indian context has been discussed with appropriate justification. The FBR programme since 1985 till 2030 is highlighted focussing on the current status and future direction of fast breeder test reactor (FBTR), prototype fast breeder reactor (PFBR) and FBR-1 and 2. Design and technological challenges of PFBR and design and safety targets with means to achieve the same are the major highlights of this paper.

  15. Overview of the Lockheed Martin Compact Fusion Reactor (CFR) Program

    Science.gov (United States)

    McGuire, Thomas

    2015-11-01

    The Lockheed Martin Compact Fusion Reactor (CFR) Program endeavors to quickly develop a compact fusion power plant with favorable commercial economics and military utility. An overview of the concept and its diamagnetic, high beta magnetically encapsulated linear ring cusp confinement scheme will be given. The analytical model of the major loss mechanisms and predicted performance will be discussed, along with the major physics challenges. Key features of an operational CFR reactor will be highlighted. The proposed developmental path following the current experimental efforts will be presented. ©2015 Lockheed Martin Corporation. All Rights Reserved.

  16. PRODUC program package for calculating correlation relations in reactor core

    International Nuclear Information System (INIS)

    To perform calculations of fission product accumulation and radionuclide activity ratio distribution in the reactor fuel assembly (FA), the PRODUC software is developed. This package allows one to obtain distributions of radionuclide activity ratios for any fuel loading of the RBMK-1000 reactor. Plutonium and cerium-144 activity ratio distribution in the FA of the fuel loading of the 4th unit of the Chernobyl NPP as of April 25, 1986 is obtained according to the PRODUC program. 6 refs.; 7 figs.; 1 tab

  17. Ageing management program for reactor components in HANARO

    International Nuclear Information System (INIS)

    The HANARO, an open-tank-in-pool type research reactor of 30MWth power in Korea, has operated for 8 years since its initial criticality in February of 1995. The reactor power has been gradually increased to 24 MWth through the service period. Therefore the reactor age is very young from the viewpoint of the ageing effect on the reactor structure and components by neutron irradiation considering the expected reactor lifetime. But, we have a few programs to manage the ageing from the aspect of design lifetime of reactor components. This paper summarizes the overall progress and plan for the ageing management for the reactor components including lifetime extension and design improvement, remote measurements and in-service inspections. The shutoff units and control absorber units have aged more rapidly than other structures or components because the number of rod drop cycles was higher than expected at the design stage. The system commissioning tests, periodic performance tests, and weekly operation for the stable supply of medical radioisotopes overriding the normal cycle operation have contributed to the high frequency of rod drop. Therefore, we have instituted a program to extend the lifetime of the shutoff units and the control absorber units. This program includes an endurance test to verify the performance for the extended number of drops and the management of shutdown methods to minimize the drop cycles for both the shutoff units and the control absorber units. The program also includes the design improvement of the damper mechanism of the control absorber units to reduce the impact force caused by rod drop. The inner shell of the reflector vessel surrounding the core is the most critical part from the viewpoint of neutron irradiation. The periodic measurement of the dimensional change in the vertical straightness of the inner shell is considered as one of the in-service inspections. We developed a few tools and verified the performance to measure the

  18. The DOE Advanced Gas Reactor Fuel Development and Qualification Program

    International Nuclear Information System (INIS)

    The high outlet temperatures and high thermal-energy conversion efficiency of modular High Temperature Gas-cooled Reactors (HTGRs) enable an efficient and cost effective integration of the reactor system with non-electricity generation applications, such as process heat and/or hydrogen production, for the many petrochemical and other industrial processes that require temperatures between 300 C and 900 C. The Department of Energy (DOE) has selected the HTGR concept for the Next Generation Nuclear Plant (NGNP) Project as a transformative application of nuclear energy that will demonstrate emissions-free nuclear-assisted electricity, process heat, and hydrogen production, thereby reducing greenhouse-gas emissions and enhancing energy security. The objective of the DOE Advanced Gas Reactor (AGR) Fuel Development and Qualification program is to qualify tristructural isotropic (TRISO)-coated particle fuel for use in HTGRs. The Advanced Gas Reactor Fuel Development and Qualification Program consists of five elements: fuel manufacture, fuel and materials irradiations, post-irradiation examination (PIE) and safety testing, fuel performance modeling, and fission-product transport and source term evaluation. An underlying theme for the fuel development work is the need to develop a more complete, fundamental understanding of the relationship between the fuel fabrication process and key fuel properties, the irradiation and accident safety performance of the fuel, and the release and transport of fission products in the NGNP primary coolant system. An overview of the program and recent progress is presented.

  19. Evaluation for the effects of a ring plate device to eliminate free surface gradients in liquid metal fast breeder reactor vessel using multi-dimensional thermohydraulics computer code

    Energy Technology Data Exchange (ETDEWEB)

    Gao Ming Qing

    1997-02-01

    There is a free surface at the upper plenum in a reactor vessel of LMFBR. The free surface has spatial gradient caused by the internal coolant flow. This is a disadvantageous factor to engineering from the view point of gas entrainment into coolant. To eliminate the free surface gradients, ring plates about 20 cm wide are fitted at about 1 meter under the free surface. They interfere fluid flow, and decrease the component velocity in vertical direction. To investigate the efficiency of the ring plates, analyses with the AQUA-VOF code were carried out. For contrast, three conditions were given: Case-1: Without ring plates. Case-2: Ring plates, fitted at 1.125 m under the free surface. Case-3: Ring plates, fitted at 1.5 m under the free surface. The results shown that the ring plates have a sufficiently high potential to eliminate the free surface gradients due to disperse the momentum along reactor vessel axis to radial direction. In the calculations with ring plate (Cases-2 and -3), the maximum free surface height differences and the maximum gradients of free surface were decreased to less than 15% and 64% compared with the case without ring plates, respectively. (author)

  20. The reactor engineer program: creating a new workforce

    International Nuclear Information System (INIS)

    As the number of nuclear engineering schools continues to shrink across the U.S., talented professional engineers for the nuclear energy community must increasingly be found elsewhere. To meet its needs, therefore, the Office of Nuclear Reactor Regulation (NRR) established an Intern Program to bring new talent into the NRC. The two-year program includes 17 weeks of technical training, and 4 or 5 rotational assignments, including at least 4 months at a commercial nuclear power plant site. The key to the success of the program is the full support of NRR high-level management

  1. Generation IV Reactors Integrated Materials Technology Program Plan: Focus on Very High Temperature Reactor Materials

    Energy Technology Data Exchange (ETDEWEB)

    Corwin, William R [ORNL; Burchell, Timothy D [ORNL; Katoh, Yutai [ORNL; McGreevy, Timothy E [ORNL; Nanstad, Randy K [ORNL; Ren, Weiju [ORNL; Snead, Lance Lewis [ORNL; Wilson, Dane F [ORNL

    2008-08-01

    Since 2002, the Department of Energy's (DOE's) Generation IV Nuclear Energy Systems (Gen IV) Program has addressed the research and development (R&D) necessary to support next-generation nuclear energy systems. The six most promising systems identified for next-generation nuclear energy are described within this roadmap. Two employ a thermal neutron spectrum with coolants and temperatures that enable hydrogen or electricity production with high efficiency (the Supercritical Water Reactor-SCWR and the Very High Temperature Reactor-VHTR). Three employ a fast neutron spectrum to enable more effective management of actinides through recycling of most components in the discharged fuel (the Gas-cooled Fast Reactor-GFR, the Lead-cooled Fast Reactor-LFR, and the Sodium-cooled Fast Reactor-SFR). The Molten Salt Reactor (MSR) employs a circulating liquid fuel mixture that offers considerable flexibility for recycling actinides and may provide an alternative to accelerator-driven systems. At the inception of DOE's Gen IV program, it was decided to significantly pursue five of the six concepts identified in the Gen IV roadmap to determine which of them was most appropriate to meet the needs of future U.S. nuclear power generation. In particular, evaluation of the highly efficient thermal SCWR and VHTR reactors was initiated primarily for energy production, and evaluation of the three fast reactor concepts, SFR, LFR, and GFR, was begun to assess viability for both energy production and their potential contribution to closing the fuel cycle. Within the Gen IV Program itself, only the VHTR class of reactors was selected for continued development. Hence, this document will address the multiple activities under the Gen IV program that contribute to the development of the VHTR. A few major technologies have been recognized by DOE as necessary to enable the deployment of the next generation of advanced nuclear reactors, including the development and qualification of

  2. Studies on sodium boiling phenomena in out of pile rod bundles for various accidental situations in Liquid Metal Fast Breeder Reactors (LMFBR) experiments and interpretations

    Science.gov (United States)

    Seiler, J. M.; Rameau, B.

    Bundle sodium boiling in nominal geometry for different accident conditions is reviewed. Voiding of a subassembly is controlled by not only hydrodynamic effects but mainly by thermal effects. There is a strong influence of the thermal inertia of the bundle material compared to the sodium thermal inertia. Flow instability, during a slow transient, can be analyzed with numerical tools and estimated using simplified approximations. Stable boiling operational conditions under bundle mixed convection (natural convection in the reactor) can be predicted. Voiding during a fast transient can be approximated from single channel calculations. The phenomenology of boiling behavior for a subassembly with inlet completely blocked, submitted to decay heat and lateral cooling; two-phase sodium flow pressure drop in a tube of large hydraulic diameter under adiabatic conditions; critical flow phenomena and voiding rate under high power, slow transient conditions; and onset of dry out under local boiling remains problematical.

  3. Final Safety Analysis Addenda to Hazards Summary Report, Experimental Breeder Reactor II (EBR-II): upgrading of plant protection system. Volume II

    Energy Technology Data Exchange (ETDEWEB)

    Allen, N. L.; Keeton, J. M.; Sackett, J. I. [comps.

    1980-06-01

    This report is the second in a series of compilations of the formal Final Safety Analysis Addenda (FSAA`s) to the EBR-II Hazard Summary Report and Addendum. Sections 2 and 3 are edited versions of the original FSAA`s prepared in support of certain modifications to the reactor-shutdown-system portion of the EBR-II plant-protection system. Section 4 is an edited version of the original FSAA prepared in support of certain modifications to a system classified as an engineered safety feature. These sections describe the pre- and postmodification system, the rationale for the modification, and required supporting safety analysis. Section 5 provides an updated description and analysis of the EBR-II emergency power system. Section 6 summarizes all significant modifications to the EBR-II plant-protection system to date.

  4. Preliminary Study on Melting and Reaction with Liquid Metal Breeders for Developing the Korean Test Blanket Module in ITER

    Energy Technology Data Exchange (ETDEWEB)

    Lee, D. W.; Yoon, J. S.; Kim, S. K.; Lee, E. H. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, H. G. [National Fusion Research Institute, Daejeon (Korea, Republic of)

    2012-05-15

    A liquid breeder blanket has been developed in parallel with the International Thermonuclear Experimental Reactor (ITER) Test Blanket Module (TBM) program in Korea. The Korea Atomic Energy Research Institute (KAERI) has developed the liquid TBM. In the Korean liquid TBM and breeder blanket, liquid lithium (Li) and lead-lithium (PbLi) are considered as breeders. Related research has been performed: an Experimental Loop for a Liquid breeder (ELLI) constructed to develop an electromagnetic (EM) pump for circulating the liquid breeder, a magnetohydrodynamic (MHD) experiment, and a flow corrosion test. In the ELLI, Pb-15.7Li, where Li is 15.7 at % (called PbLi hereafter), is used as the breeding material. It was purchased from Stachow Metall Company, Germany, and its impurities are shown in Table 1. An EM pump circulates the material in the loop with a maximum flow rate of 60 lpm. The operating pressure and temperature in the loop are 0.4 MPa and 300 .deg. C, respectively, and the maximum operating pressure and temperature are 0.5 MPa and 550 .deg. C Before the loop operation, the melting and solidifying temperatures of the PbLi were measured for ascertaining whether it will show a consistent value for the many cycles of heating and cooling at various conditions of the loop operation. We can also investigate the contamination of PbLi according to the cyclic use. Of the liquid type breeder materials, PbLi is much safer than Li itself, as liquid metal can be ignited when it meets with water or air. There is still a concern regarding the use of PbLi, and it has not been fully proven whether it will react with water or air when it is in a molten state, as it contains lithium. Therefore, reaction tests of Li and PbLi with air and water were performed for safety reasons using the prepared test chamber

  5. Comparative study of unprotected loss of flow accident analysis of 1000 MWe and 500 MWe Fast Breeder Reactor Metal (FBR-M) cores and their inherent safety

    International Nuclear Information System (INIS)

    Research highlights: → ULOF analysis of metal (U-Pu-6% Zr) fuelled 500 MWe and 1000 MWe pool type FBR. → Uncertainties (typically 20%) on the sensitive feedback parameters. → Sensitive parameters - core radial feedback and sodium void reactivity effect. → Transient behavior of both 500 MWe and 1000 MWe core are benign under ULOFA. → For 1000 MWe inherent safety is assured with limited sodium void reactivity. - Abstract: Unprotected loss of flow (ULOF) analysis of metal (U-Pu-6% Zr) fuelled 500 MWe and 1000 MWe pool type FBR are studied to verify the passive shutdown capability and its inherent safety parameters. Study is also made with uncertainties (typically 20%) on the sensitive feedback parameters such as core radial expansion feedback and sodium void reactivity effect. Inference of the study is, nominal transient behavior of both 500 MWe and 1000 MWe core are benign under unprotected loss of flow accident (ULOFA) and the transient power reduces to natural circulation based Safety Grade Decay Heat Removal (SGDHR) system capacity before the initiation of boiling. Sensitivity analysis of 500 MWe shows that the reactor goes to sub-critical and the transient power reduces to SGDHR system capacity before the boiling initiation. In the sensitivity analysis of 1000 MWe core, initiation of voiding and fuel melting occurs. But, with 80% core radial expansion reactivity feedback and nominal sodium expansion reactivity feedback, the reactor was maintained substantially sub-critical even beyond when net power crosses the SGDHR system capacity. From the study, it is concluded that if the sodium void reactivity is limited (4.6 $) then the inherent safety of 1000 MWe design is assured, even with 20% uncertainty on the sensitive parameters.

  6. The BLOW-3A: A theoretical model to describe transient two phase flow conditions in Liquid Metal Fast Breeder Reactor (LMFBR) coolant channels

    Science.gov (United States)

    Bottoni, M.; Struwe, D.

    The theoretical background of the BLOW-3A program is reported, including the basic equations used to determine temperature fields in the fuel, clad, coolant and structure material as well as the coolant dynamics in single and two-phase flow conditions. The two-phase flow model assumes an annular flow regime. Special aspects to calculate two-phase pressure drops for these conditions are discussed. Examples of the experimental validation of the program are given.

  7. A reliability-centered maintenance program for primary reactor pumps

    International Nuclear Information System (INIS)

    Reactor coolant and recirculation pumps require significant outage times to repair and, as a consequence, are a major contributor to plant downtime and lost capacity. To improve reliability of these primary reactor pumps, a comprehensive preventative maintenance program has been developed using the principles of reliability-centered maintenance. This method establishes the frequency of past failures, estimates the probability of future occurrences, and assesses the effect of all potential functional failures of the pump. Maintenance tasks are then defined to address those specific failure modes that have the largest probability of occurrence and the greatest impact on plant availability. Benefits include: improved reliability, a maintenance program that satisfies the industry initiative on maintenance, prudence documentation in support of unforeseen outages, and documented justification for rate-base increases for maintenance costs

  8. Modification of reference temperature program in reactor regulating system

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Sung Sik; Lee, Byung Jin; Kim, Se Chang; Cheong, Jong Sik [Korea Power Engineering Company, Inc., Seoul (Korea, Republic of); Kim, Ji In; Doo, Jin Yong [Korea Electric Power Cooperation, Yonggwang (Korea, Republic of)

    1998-12-31

    In Yonggwang nuclear units 3 and 4 currently under commercial operation, the cold temperature was very close to the technical specification limit of 298 deg C during initial startup testing, which was caused by the higher-than-expected reactor coolant system flow. Accordingly, the reference temperature (Tref) program needed to be revised to allow more flexibility for plant operations. In this study, the method of a specific test performed at Yonggwang nuclear unit 4 to revise the Tref program was described and the test results were discussed. In addition, the modified Tref program was evaluated on its potential impacts on system performance and safety. The methods of changing the Tref program and the associated pressurizer level setpoint program were also explained. Finally, for Ulchin nuclear unit 3 and 4 currently under initial startup testing, the effects of reactor coolant system flow rate on the coolant temperature were evaluated from the thermal hydraulic standpoint and an optimum Tref program was recommended. 6 refs., 4 figs., 2 tabs. (Author)

  9. Draft supplement to final environmental statement related to construction and operation of Clinch River Breeder Reactor Plant. Docket No. 50-537

    International Nuclear Information System (INIS)

    Information is presented concerning the site and environs; facility description; environmental impacts due to construction; environmental impacts of plant operation; environmental measurement and monitoring programs; environmental impacts of postulated accidents; need for the proposed facility; alternatives; evaluation of the proposed action; and discussion of comments received on the draft environmental statement

  10. 用于池式快堆系统分析的钠池三维模型开发%Development of Three-Dimensional Sodium Pool Model for System Analysis of Pool-Type Liquid Metal Fast Breeder Reactor

    Institute of Scientific and Technical Information of China (English)

    隋丹婷; 陆道纲; 张盼

    2012-01-01

    由于池式快堆钠池内的热工水力学特性对反应堆的安全运行有重要影响,本文采用基于交错网格的SIMPLE算法开发直角坐标系和柱坐标系下钠池三维计算软件.应用CFX软件进行验证之后,完成了三维流场分析程序与系统分析软件SAC-CFR的耦合,并用耦合后的程序分析日本文殊快堆45%功率稳态运行工况上腔室内的流场分布,初步验证了堆芯上腔三维化的SAC-CFR用于系统分析的有效性,为进一步开发事故模型、非能动余热排出系统模型做准备.%As the thermal-hydraulic characteristic in sodium pool is crucial for safety operation of liquid metal fast breeder reactor (LMFBR), a three-dimensional sodium pool thermal-hydraulic analysis code was developed based on SIMPLE algorithm on stagger grid under Cartesian coordinates and cylindrical coordinates. After the validation with CFX, coupling between the analysis code and SAC-CFR was completed) and then the coupled code was applied to the flow field analysis in upper plenum of Monju Plant at 45% thermal power steady-state operation condition, which preliminary shows the effectiveness of the system analysis with coupled code and makes preparations for further development of accident analysis model and passive residual heat removal system.

  11. Preventive maintenance program for a research and production reactor

    International Nuclear Information System (INIS)

    This program proposes a simple, rapid and efficient methodology for the task of developing a really preventive maintenance discipline. Moreover, the lower cost of its application -since it must satisfy the plant's budget-. To this purpose, an extremely economical and easily obtainable infrastructure is proposed. The following stage is referred to the commissioning system, subsequent supervision and follow-up. The experience gained from the two reactors as RA-6 (Bariloche Atomic Center) and NUR (RAE) of Argelia. Finally, the interacting characteristic of this program, since it may be rapidly adapted to different dimensions of plants, laboratories, etc., must be pointed out. (Author)

  12. ITER solid breeder blanket materials database

    Energy Technology Data Exchange (ETDEWEB)

    Billone, M.C. [Argonne National Lab., IL (United States); Dienst, W. [Kernforschungszentrum Karlsruhe GmbH (Germany). Inst. fuer Material- und Festkoerperforschung; Flament, T. [CEA Centre d`Etudes de Fontenay-aux-Roses (France). Commissariat A L`Energie Atomique; Lorenzetto, P. [NET Team, Garching (Germany); Noda, K. [Japan Atomic Energy Research Inst., Takai, Ibaraki, (Japan); Roux, N. [CEA Centre d`Etudes et de Recherches Les Materiaux (France). Commissariat a L`Energie Atomique

    1993-11-01

    The databases for solid breeder ceramics (Li{sub 2},O, Li{sub 4}SiO{sub 4}, Li{sub 2}ZrO{sub 3} and LiAlO{sub 2}) and beryllium multiplier material are critically reviewed and evaluated. Emphasis is placed on physical, thermal, mechanical, chemical stability/compatibility, tritium, and radiation stability properties which are needed to assess the performance of these materials in a fusion reactor environment. Correlations are selected for design analysis and compared to the database. Areas for future research and development in blanket materials technology are highlighted and prioritized.

  13. Review of selected aspects of the Army Gas-Cooled Reactor Systems Program

    Energy Technology Data Exchange (ETDEWEB)

    None

    1965-08-27

    Information is presented concerning the AGCRS program; ML-1 reactor skid refurbishing program; ML-1-IM fabrication status; power conversion system component testing program; ML-1 demonstration test program; and applications of ML-1 technology.

  14. Decommissioning the Los Alamos Molten Plutonium Reactor Experiment (LAMPRE I)

    International Nuclear Information System (INIS)

    The Los Alamos Molten Plutonium Reactor Experiment (LAMPRE I) was decommissioned at the Los Alamos National Laboratory, Los Alamos, New Mexico, in 1980. The LAMPRE I was a sodium-cooled reactor built to develop plutonium fuels for fast breeder applications. It was retired in the mid-1960s. This report describes the decommissioning procedures, the health physics programs, the waste management, and the costs for the operation

  15. Program plan for decontamination and decommissioning the Materials Testing Reactor at the INEL

    International Nuclear Information System (INIS)

    A discussion is presented of a program plan developed for the dismantling of the Materials Testing Reactor located in the Testing Reactor Area (TRA) of the Idaho National Engineering Laboratory. Included are the scope of work, dismantling problems resulting from the nature of construction of the MTR, and a program plan for physically dismantling the reactor

  16. Participation in the U.S. Department of Energy Reactor Sharing Program

    Energy Technology Data Exchange (ETDEWEB)

    Mulder, R. U.; Benneche, P. E.; Hosticka, B.

    1998-09-30

    The objective of the DOE supported Reactor Sharing Program is to increase the availability of university nuclear reactor facilities to non-reactor-owning educational institutions. The educational and research programs of these users institutions is enhanced by the use of the nuclear facilities.

  17. 77 FR 36014 - Initial Test Program of Emergency Core Cooling Systems for Boiling-Water Reactors

    Science.gov (United States)

    2012-06-15

    ... COMMISSION Initial Test Program of Emergency Core Cooling Systems for Boiling-Water Reactors AGENCY: Nuclear...-1277, ``Initial Test Program of Emergency Core Cooling Systems for Boiling- Water Reactors.'' This... testing features of emergency core cooling systems (ECCSs) for boiling-water reactors (BWRs)....

  18. Participation in the U.S. Department of Energy Reactor Sharing Program

    International Nuclear Information System (INIS)

    The objective of the DOE supported Reactor Sharing Program is to increase the availability of university nuclear reactor facilities to non-reactor-owning educational institutions. The educational and research programs of these users institutions is enhanced by the use of the nuclear facilities

  19. Gas reactor international cooperative program interim report: German Pebble Bed Reactor design and technology review

    International Nuclear Information System (INIS)

    This report describes and evaluates several gas-cooled reactor plant concepts under development within the Federal Republic of Germany (FRG). The concepts, based upon the use of a proven Pebble Bed Reactor (PBR) fuel element design, include nuclear heat generation for chemical processes and electrical power generation. Processes under consideration for the nuclear process heat plant (PNP) include hydrogasification of coal, steam gasification of coal, combined process, and long-distance chemical heat transportation. The electric plant emphasized in the report is the steam turbine cycle (HTR-K), although the gas turbine cycle (HHT) is also discussed. The study is a detailed description and evaluation of the nuclear portion of the various plants. The general conclusions are that the PBR technology is sound and that the HTR-K and PNP plant concepts appear to be achievable through appropriate continuing development programs, most of which are either under way or planned

  20. Advanced CANDU reactor development: a customer-driven program

    International Nuclear Information System (INIS)

    The Advanced CANDU Reactor (ACR) product development program is well under way. The development approach for the ACR is to ensure that all activities supporting readiness for the first ACR project are carded out in parallel, as parts of an integrated whole. In this way design engineering, licensing, development and testing, supply chain planning, construct ability and module strategy, and planning for commissioning and operations, all work in synergy with one another. Careful schedule management :ensures that program focus stays on critical path priorities.'This paper provides an overview of the program, with an emphasis on integration to ensure maximum project readiness, This program management approach is important now that AECL is participating as the reactor vendor in Dominion Energy's DOE-sponsored Combined Construction/Operating License (COL) program. Dominion Energy selected the ACR-700 as their reference reactor technology for purposes of demonstrating the COL process. AECL's development of the ACR is unique in that pre-licensing activities are being carded out parallel in the USA and Canada, via independent, but well-communicated programs. In the short term, these programs are major drivers of ACR development. The ACR design approach has been to optimize to achieve major design objectives: capital cost reduction, robust design with ample margins, proveness by using evolutionary change from existing :reference plants, design for ease :of operability. The ACR development program maintains these design objectives for each of the program elements: Design: .Carefully selected design innovations based on the SEU fuel/light water coolant:/heavy water moderator approach. Emphasis on lessons-learned review from operating experience and customer feedback Licensing: .Safety case based on strengths of existing CANDU plus benefits of optimised design Development and Test: Choice of materials, conditions to enable incremental testing building on existing CANDU and LWR

  1. Status report. KfK contribution to the development of DEMO-relevant test blankets for NET/ITER. Pt. 2: BOT helium cooled solid breeder blanket. Vol. 2

    International Nuclear Information System (INIS)

    The BOT (Breeder Outside Tube) Helium Cooled Solid Breeder Blanket for a fusion Demo reactor and the status of the R and D program is presented. This is the KfK contribution to the European Program for the Demo relevant test blankets to be irradiated in NET/ITER. Volume 1 (KfK 4928) contains the summary, volume 2 (KfK 4929) a more detailed version of the report. In both volumes are described the reasons for the selected design, the reference blanket design for the Demo reactor, the design of the test blanket including the ancillary systems together with the present status of the relative R and D program in the fields of neutronic and thermohydraulic calculations, of the electromagnetic forces caused by disruptions, of the development and irradiation of the ceramic breeder material, of the tritium release and recovery, and of the technological investigations. An outlook is given on the required R and D program for the BOT Helium Cooled Solid Breeder Blanket prior to tests in NET/ITER and the proposed test program in NET/ITER. (orig.)

  2. The RERTR [Reduced Enrichment Research and Test Reactor] program:

    International Nuclear Information System (INIS)

    The progress of the Reduced Enrichment Research and Test Reactor (RERTR) program is described. After a brief summary of the results which the RERTR program, in collaboration with its many international partners, had achieved by the end of 1986, the activities, results and new developments which ocurred in 1987 are reviewed. Irradiation of the second miniplate series, concentrating on U3Si2-Al and U3Si-Al fuels was completed and postirradiation examinations were performed on many of its miniplates. The whole-core ORR demonstration with U3Si2-Al fuel at 4.8 g U/cm3 was completed at the end of March with excellent results and with 29 elements estimated to have reached at least 40 % average burnup. Good progress was made in the area of LEU usage for the production of fission 99Mo, and in the coordination of safety evaluations related to LEU conversions of U.S. university reactors. Planned activities include testing and demonstrating advanced fuels intended to allow use of reduced enrichment uranium in very-high-performance reactors. Two candidate fuels are U3Si-Al with 19.75 % enrichment and U3Si2-Al with 45 % enrichment. Demonstration of these fuels will include irradiation of full-size elements and, possibly, a full-core demonstration. Achievement of the final program goals is still projected for 1990. This progress could not have been possible without the close international cooperation which has existed from the beginning, and which is essential to the ultimate success of the RERTR program. (Author)

  3. Materials Inventory Database for the Light Water Reactor Sustainability Program

    Energy Technology Data Exchange (ETDEWEB)

    Kazi Ahmed; Shannon M. Bragg-Sitton

    2013-08-01

    Scientific research involves the purchasing, processing, characterization, and fabrication of many sample materials. The history of such materials can become complicated over their lifetime – materials might be cut into pieces or moved to various storage locations, for example. A database with built-in functions to track these kinds of processes facilitates well-organized research. The Material Inventory Database Accounting System (MIDAS) is an easy-to-use tracking and reference system for such items. The Light Water Reactor Sustainability Program (LWRS), which seeks to advance the long-term reliability and productivity of existing nuclear reactors in the United States through multiple research pathways, proposed MIDAS as an efficient way to organize and track all items used in its research. The database software ensures traceability of all items used in research using built-in functions which can emulate actions on tracked items – fabrication, processing, splitting, and more – by performing operations on the data. MIDAS can recover and display the complete history of any item as a simple report. To ensure the database functions suitably for the organization of research, it was developed alongside a specific experiment to test accident tolerant nuclear fuel cladding under the LWRS Advanced Light Water Reactor Nuclear Fuels Pathway. MIDAS kept track of materials used in this experiment from receipt at the laboratory through all processes, test conduct and, ultimately, post-test analysis. By the end of this process, the database proved to be right tool for this program. The database software will help LWRS more efficiently conduct research experiments, from simple characterization tests to in-reactor experiments. Furthermore, MIDAS is a universal tool that any other research team could use to organize their material inventory.

  4. Light Water Reactor Sustainability Program: Reactor Safety Technologies Pathway Technical Program Plan

    International Nuclear Information System (INIS)

    In the aftermath of the March 2011 multi-unit accident at the Fukushima Daiichi nuclear power plant (Fukushima), the nuclear community has been reassessing certain safety assumptions about nuclear reactor plant design, operations and emergency actions, particularly with respect to extreme events that might occur and that are beyond each plant's current design basis. Because of our significant domestic investment in nuclear reactor technology (99 operating reactors in the fleet of commercial LWRs with five under construction), the United States has been a major leader internationally in these activities. The U.S. nuclear industry is voluntarily pursuing a number of additional safety initiatives. The NRC continues to evaluate and, where deemed appropriate, establish new requirements for ensuring adequate protection of public health and safety in the occurrence of low probability events at nuclear plants; (e.g., mitigation strategies for beyond design basis events initiated by external events like seismic or flooding initiators). The DOE has also played a major role in the U.S. response to the Fukushima accident. Initially, DOE worked with the Japanese and the international community to help develop a more complete understanding of the Fukushima accident progression and its consequences, and to respond to various safety concerns emerging from uncertainties about the nature of and the effects from the accident. DOE R&D activities are focused on providing scientific and technical insights, data, analyses methods that ultimately support industry efforts to enhance safety. These activities are expected to further enhance the safety performance of currently operating U.S. nuclear power plants as well as better characterize the safety performance of future U.S. plants. In pursuing this area of R&D, DOE recognizes that the commercial nuclear industry is ultimately responsible for the safe operation of licensed nuclear facilities. As such, industry is considered the

  5. Light Water Reactor Sustainability Program: Reactor Safety Technologies Pathway Technical Program Plan

    Energy Technology Data Exchange (ETDEWEB)

    Corradini, M. L. [Univ. of Wisconsin, Madison, WI (United States)

    2015-06-01

    In the aftermath of the March 2011 multi-unit accident at the Fukushima Daiichi nuclear power plant (Fukushima), the nuclear community has been reassessing certain safety assumptions about nuclear reactor plant design, operations and emergency actions, particularly with respect to extreme events that might occur and that are beyond each plant’s current design basis. Because of our significant domestic investment in nuclear reactor technology (99 operating reactors in the fleet of commercial LWRs with five under construction), the United States has been a major leader internationally in these activities. The U.S. nuclear industry is voluntarily pursuing a number of additional safety initiatives. The NRC continues to evaluate and, where deemed appropriate, establish new requirements for ensuring adequate protection of public health and safety in the occurrence of low probability events at nuclear plants; (e.g., mitigation strategies for beyond design basis events initiated by external events like seismic or flooding initiators). The DOE has also played a major role in the U.S. response to the Fukushima accident. Initially, DOE worked with the Japanese and the international community to help develop a more complete understanding of the Fukushima accident progression and its consequences, and to respond to various safety concerns emerging from uncertainties about the nature of and the effects from the accident. DOE R&D activities are focused on providing scientific and technical insights, data, analyses methods that ultimately support industry efforts to enhance safety. These activities are expected to further enhance the safety performance of currently operating U.S. nuclear power plants as well as better characterize the safety performance of future U.S. plants. In pursuing this area of R&D, DOE recognizes that the commercial nuclear industry is ultimately responsible for the safe operation of licensed nuclear facilities. As such, industry is considered the primary

  6. TREAT light water reactor source term experiments program

    International Nuclear Information System (INIS)

    Four experiments are being conducted in the TREAT facility to investigate the behavior of fission products released from typical LWR fuel overheated to the point of catastrophic cladding degradation. Heatup and steam flow transients are used that simulate the conditions expected in operating power reactors undergoing various types of hypothetical severe accidents. The experiments are integral in nature and are aimed at the physicochemical characterization, near the point of origin, of the biologically important volatile fission products released early in such accidents. Detailed program objectives are discussed, a test matrix is presented, and the test apparatus is described. Pretest analysis and preliminary results are reported for the first test

  7. Reactor Engineering Department annual report (April 1, 1987 - March 31, 1988)

    International Nuclear Information System (INIS)

    This report summarizes the research and development activities in the Department of Reactor Engineering during the fiscal year of 1987 (April 1, 1987 - March 31, 1988). The major activities in the Department concerns the programs of the high temperature gas-cooled reactor, the high conversion light water reactor, the advanced fission reactor system and the fusion reactor at JAERI and the fast breeder reactor at PNC. The report contains the latest progress in nuclear data and group constants, theoretical methods and code development, reactor physics experiments and analyses, fusion neutronics, shielding, reactor and nuclear instrumentation, reactor control/diagnosis and robotics, as well as the new topics from this fiscal year on advanced reactors system design studies and technique developments related the facilities in the Department. Also described are the activities of the Research Committee on Reactor Physics. (author)

  8. CASSANDRE, 2-D Reactor Dynamic FEM Program with Thermohydraulic Feedback

    International Nuclear Information System (INIS)

    1 - Description of program or function: CASSANDRE is a two-dimensional (x-y or r-z) finite-elements neutronics code with thermohydraulic feedback for reactor dynamics prior to the disassembly phase. The code was conceived in order to be coupled with any thermohydraulics module, although thermohydraulics feedback is only considered in r-z geometry. In the steady state, criticality search is possible either by control-rod insertion or by homogeneous poisoning of the coolant. 2 - Method of solution: The program uses multigroup diffusion theory. Its main characteristics are the use of a generalized quasi-static model, the use of a flexible multigroup point-kinetics algorithm allowing for spectral matching, and the use of a finite elements description. 3 - Restrictions on the complexity of the problem: The user must prepare a cross section library

  9. Prioritization of R and D programs on probabilistic reactor safety

    International Nuclear Information System (INIS)

    An interactive computer code based on the multiattribute utility theory has been developed with graphic capabilities to use in selection of probabilistic reactor safety RandD programs. Utility values and proper graphic representation are made through lottery games on the computer terminal. The code is applied to prioritize a set of RandD programs on LWR safety based on attributes including regulatory issues, institutional issues and operation problems. The methodology is described here in detail with its applications. Some of the input includes statistical distributions and subjective judgments on institutional issues. The flexibility of the approach provides a tool for decision makers whether on individual or group level to assess LWR safety priorities and continuously update their strategies

  10. Environmental assessment for Breeder Reprocessing Engineering Test (BRET): Revision 1

    International Nuclear Information System (INIS)

    This Environmental Assessment (EA) is for the proposed installation and operation of an integrated breeder fuel reprocessing test system in the shielded cells of the Fuels and Materials Examination Facility (FMEF) at Hanford and the associated modifications to the FMEF to accommodate BRET. These modifications would begin in FY-1986 subject to Congressional authorization. Hot operations would be scheduled to start in the early 1990's. The system, called the Breeder Reprocessing Engineering Test (BRET), is being designed to provide a test capability for developing the demonstrating fuel reprocessing, remote maintenance, and safeguards technologies for breeder reactor fuels. This EA describes (1) the action being proposed, (2) the existing environment which would be affected, (3) the potential environmental impacts from normal operations and severe accidents from the proposed action, (4) potential conflicts with federal, state, regional, and/or local plans for the area, and (5) environmental implications of alternatives considered to the proposed action. 41 refs., 10 figs., 31 tabs

  11. On the history of the Fast Breeder Project

    International Nuclear Information System (INIS)

    The evolution of the Fast Breeder Project from its beginning at the Karlsruhe Nuclear Research Center to the present cooperation of various organisations especially in the Federal Republic of Germany, the Netherlands, Belgium and France is described in its historical context. Where as the emphasis was on physical studies of fast neutron cores in the early phase, technological and safety problems gained importance in the subsequent development. The increasing collaboration with industry and the support by government funds resulted in the design and start of construction of the prototype SNR 300. The objectives and the reasoning underlying important intermediate decisions are described. In the meantime, licensing and funding problems have become decisive for the project schedule. The present report also gives an account of the international and national political aspects which influence the breeder reactor development. In the annex all fast breeder publications of the Karlsruhe Nuclear Research Center are listed. (orig.)

  12. Fast-Breeder-Blanket Project: FBBF. Final report

    International Nuclear Information System (INIS)

    This report is the final report for DOE contract DE-AC02-76ET37237 with the Purdue Fast Breeder Blanket Project. The Project was initiated to investigate the uncertainties in Fast Breeder Reactor blanket calculations. Absolute measurements of key neutron reaction rates, neutron spectra, and gamma-ray energy depositions were made in simulated FBF blankets in the Fast Breeder Blanket Facility (FBBF), a Cf-252 driven subcritical facility. Calculation of the spectra and integral reaction rates were made using methods, computer codes, and cross section data typical of those currently used in the design of FBR's. Comparisons of calculated to experimental integral neutron reaction rates give good agreement at the inner portions of the blanket by diverge to C/E ratios of about 0.65 at the outer edge of the blanket for reactions sensitive to the neutron density

  13. Thermohydraulic modeling and simulation of breeder reactors

    International Nuclear Information System (INIS)

    This paper deals with the modeling and simulation of system-wide transients in LMFBRs. Unprotected events (i.e., the presumption of failure of the plant protection system) leading to core-melt are not considered in this paper. The existing computational capabilities in the area of protected transients in the US are noted. Various physical and numerical approximations that are made in these codes are discussed. Finally, the future direction in the area of model verification and improvements is discussed

  14. Liquid Metal Fast Breeder Reactors: a bibliography

    International Nuclear Information System (INIS)

    This bibliogralphy includes 5465 selected citations on LMFBR development. The citations were compiled from the DOE Energy Data Base covering the period January 1978 (EDB File No. 78R1087) through August 1980 (EDB File No. 80C79142). The references are to reports from the Department of Energy and its contractors, reports from other government or private organizations, and journal articles, books, conference papers, and monographs from US originators. Report citations are arranged alphanumerically by report number; nonreport literature citations are arranged chronologically. Corporate, Personal Author, Subject, and Report Number Indexes are provided in Volume 2

  15. Liquid Metal Fast Breeder Reactors: a bibliography

    International Nuclear Information System (INIS)

    This bibliography includes 5465 selected citations on LMFBR development. The citations were compiled from the DOE Energy Data Base covering the period January 1978 (EDB File No. 78R1087) through August 1980 (EDB File No. 80C79142). The references are to reports from the Department of Energy and its contractors, reports from other government or private organizations, and journal articles, books, conference papers, and monographs from US originators. Report citations are arranged alphanumerically by report number; nonreport literature citations are arranged chronologically. Corporate, Personal Author, Subject, and Report Number Indexes are provided in Volume 2

  16. Liquid Metal Fast Breeder Reactors: a bibliography

    Energy Technology Data Exchange (ETDEWEB)

    Raleigh, H.D. (ed.)

    1980-11-01

    This bibliography includes 5465 selected citations on LMFBR development. The citations were compiled from the DOE Energy Data Base covering the period January 1978 (EDB File No. 78R1087) through August 1980 (EDB File No. 80C79142). The references are to reports from the Department of Energy and its contractors, reports from other government or private organizations, and journal articles, books, conference papers, and monographs from US originators. Report citations are arranged alphanumerically by report number; nonreport literature citations are arranged chronologically. Corporate, Personal Author, Subject, and Report Number Indexes are provided in Volume 2.

  17. Liquid Metal Fast Breeder Reactors: a bibliography

    Energy Technology Data Exchange (ETDEWEB)

    Raleigh, H.D. (ed.)

    1980-11-01

    This bibliogralphy includes 5465 selected citations on LMFBR development. The citations were compiled from the DOE Energy Data Base covering the period January 1978 (EDB File No. 78R1087) through August 1980 (EDB File No. 80C79142). The references are to reports from the Department of Energy and its contractors, reports from other government or private organizations, and journal articles, books, conference papers, and monographs from US originators. Report citations are arranged alphanumerically by report number; nonreport literature citations are arranged chronologically. Corporate, Personal Author, Subject, and Report Number Indexes are provided in Volume 2.

  18. Startup of the FFTF sodium cooled reactor

    International Nuclear Information System (INIS)

    The Fast Flux Test Facility (FFTF), located on the Department of Energy (DOE) Hanford Reservation near Richland, Washington, is a 3 Loop 400 MW(t) sodium cooled fast reactor with a primary mission to test fuels and materials for development of the Liquid Metal Fast Breeder Reactor (LMFBR). Bringing FFTF to a condition to accomplish this mission is the goal of the Acceptance Test Program (ATP). This program was the mechanism for achieving startup of the FFTF. Highlights of the ATP involving the system inerting, liquid metal and inerted cell testing and initial ascent to full power are discussed

  19. Fabrication Technological Development of the Oxide Dispersion Strengthened Alloy MA957 for Fast Reactor Applications

    Energy Technology Data Exchange (ETDEWEB)

    Hamilton, Margaret L.; Gelles, David S.; Lobsinger, Ralph J.; Johnson, Gerald D.; Brown, W. F.; Paxton, Michael M.; Puigh, Raymond J.; Eiholzer, Cheryl R.; Martinez, C.; Blotter, M. A.

    2000-02-28

    A significant amount of effort has been devoted to determining the properties and understanding the behavior of the alloy MA957 to define its potential usefulness as a cladding material in the fast breeder reactor program. The numerous characterization and fabrication studies that were conducted are documented in this report.

  20. CRBRP flow induced vibration program

    International Nuclear Information System (INIS)

    The program to assure the structural adequacy of Clinch River Breeder Reactor (CRBRP) components during its planned 30 years of operation is described. The program includes (1) an assessment of reactor components relative to their susceptibility to FIV, (2) designing to minimize component excitation due to Fluid induced vibrations (FIV), (3) scale model tests to measure structural response during simulated operating conditions and (4) preoperational tests. An overview of the CRBRP test program is described. Additionally, details of scale model testing of reactor internals and the steam generator is described in more detail. (author)

  1. Nuclear reactor safety program in U.S. Department of Energy and future perspectives

    International Nuclear Information System (INIS)

    The U.S. Department of Energy (DOE) establishes policy, issues orders, and assures compliance with requirements. The contractors who design, construct, modify, operate, maintain and decommission DOE reactors, set forth the assessment of the safety of cognizant reactors and impliment DOE orders. Teams of experts in the Depatment, through scheduled and unscheduled review programs, reassess the safety of reactors in every phases of their lives. As new technology develops, the safety programs are reevaluated and policies are modified to accommodate these new technologies. The diagnostic capabilities of the computer using multiple alarms to enhance detection of defects and control of a reactor have been greatly utilized in reactor operating systems. The application of artificial intelligence (AI) technologies for diagnostic and even for the decision making process in the event of reactor accidents would be one of the future trends in reactor safety programs. (author)

  2. MIT nuclear reactor laboratory high school teaching program

    International Nuclear Information System (INIS)

    For the last 6 years, the Massachusetts Institute of Technology (MIT) Nuclear Reactor Laboratory's academic and scientific staffa have been conducting evening seminars for precollege science teachers, parents, and high school students from the New England area. These seminars, as outlined in this paper, are intended to give general information on nuclear technologies with specific emphasis on radiation physics, nuclear medicine, nuclear chemistry, and ongoing research activities at the MIT research reactor. The ultimate goal is to create interest or build on the already existing interest in science and technology by, for example, special student projects. Several small projects have already been completed ranging from environmental research to biological reactions with direct student involvement. Another outcome of these seminars was the change in attitudes of science teachers toward nuclear technology. Numerous letters have been received from the teachers and parents stating their previous lack of knowledge on the beneficial aspects of nuclear technologies and the subsequent inclusion of programs in their curriculum for educating students so that they may also develop a more positive attitude toward nuclear power

  3. Civilian Power Program. Part 1, Summary, Current status of reactor concepts

    Energy Technology Data Exchange (ETDEWEB)

    Author, Not Given

    1959-09-01

    This study group covered the following: delineation of the specific objectives of the overall US AEC civilian power reactor program, technical objectives of each reactor concept, preparation of a chronological development program for each reactor concept, evaluation of the economic potential of each reactor type, a program to encourage the the development, and yardsticks for measuring the development. Results were used for policy review by AEC, program direction, authorization and appropriation requests, etc. This evaluation encompassed civilian power reactors rated at 25 MW(e) or larger and related experimental facilities and R&D. This Part I summarizes the significant results of the comprehensive effort to determine the current technical and economic status for each reactor concept; it is based on the 8 individual technical status reports (Part III).

  4. Reactor instrumentation and safety circuit status review and program document

    Energy Technology Data Exchange (ETDEWEB)

    Deichman, J.L.

    1963-02-15

    This document has been prepared for internal use by the General Electric Company to serve as a program for evaluating reactor instrumentation and safety circuit equipment needs. It is intended that this document be used as a guide for defining, planning and scheduling engineering effort; budgeting of capital money; and project planning for new instrumentation systems. Effort will be made to periodically evaluate the status of the programs presented and provide updating information accordingly.After a plant has been built and operated for a number of years, it becomes apparent to operating and engineering personnel that certain modifications in controls and monitoring systems would provide both tangible and intangible benefits. Systems which were once thought to be the primary points of control shift in importance as others become recognized. As time passes this shifting spreads the main control focus from the central control desk to various other areas in the control room. Production rate increases cause instrument ranges and scales to be changed so that information on the process can still be obtained from existing equipment. Response times, sensitivity, limits, and time constants which were figured for one level must be used or revised for new levels. Further, it is discovered that the process monitoring points could be relocated or increased in number to provide more and better data on plant operation. New monitoring equipment is developed and installed to fill voids in information so production can continue meeting high standards for safety and process control. Equipment is fitted here and there in an already crowded control room, and some is even relocated to less advantageous positions to make available the necessary panel space. This in brief, is the rather complex status of Hanford Production Reactor instrumentation today.

  5. Coincidence measurements of FFTF breeder fuel subassemblies

    International Nuclear Information System (INIS)

    A prototype coincidence counter developed to assay fast breeder reactor fuel was used to measure four fast-flux test facility subassemblies at the Hanford Engineering Development Laboratory in Richland, Washington. Plutonium contents in the four subassemblies ranged between 7.4 and 9.7 kg with corresponding 240Pu-effective contents between 0.9 and 1.2 kg. Large count rates were observed from the measurements, and plots of the data showed significant multiplication in the fuel. The measured data were corrected for deadtime and multiplication effects using established formulas. These corrections require accurate knowledge of the plutonium isotopics and 241Am content in the fuel. Multiplication-corrected coincidence count rates agreed with the expected count rates based on spontaneous fission-neutron emission rates. These measurements indicate that breeder fuel subassemblies with 240Pu-effective contents up to 1.2 kg can be nondestructively assayed using the shift-register electronics with the prototype counters. Measurements using the standard Los Alamos National Laboratory shift-register coincidence electronics unit can produce an assay value accurate to +-1% in 1000 s. The uncertainty results from counting statistics and deadtime-correction errors. 3 references, 8 figures, 8 tables

  6. Nuclear proliferation and civilian nuclear power: report of the Nonproliferation Alternative Systems Assessment Program. Volume VIII. Advanced concepts

    International Nuclear Information System (INIS)

    The six advanced concepts for nuclear power systems that were selected for evaluation are: the fast mixed-spectrum reactor; the denatured molten-salt reactor; the mixed-flow gaseous-core reactor; the linear-accelerator fuel-regenerator reactor; the ternary metal-fueled electronuclear fuel-producer reactor; and the tokamak fusion-fission hybrid reactor. The design assessment was performed by identifying needs in six specific areas: conceptual plant design; reactor-physics considerations; fuel cycle alternatives; mechanical and thermal-hydraulic considerations; selection, development, and availability of materials; and engineering and operability. While none of the six concepts appears to be a credible commercial alternative to the liquid-metal fast-breeder within the Nonproliferation Alternative Systems Assessment Program horizon of 2025, there are a number of reasons for continued interest in the fast mixed-spectrum reactor: it is a once-through cycle fast reactor with proliferation risk characteristics similar to those of the light-water reactor; only about one-third as much uranium is required as for the once-through light-water reactor; the system will benefit directly from fast-breeder development programs; and, finally, the research and development required to develop the high-burnup metal fuel could benefit the on-going liquid-metal fast-breeder reactor program. Accordingly, a limited research and development effort on the high-burnup fuel seems justified, at present

  7. Fast breeder fuel cycle

    International Nuclear Information System (INIS)

    Basic elements of the ex-reactor part of the fuel cycle (reprocessing, fabrication, waste handling and transportation) are described. Possible technical and proliferation measures are evaluated, including current methods of accountability, surveillance and protection. The reference oxide based cycle and advanced cycles based on carbide and metallic fuels are considered utilizing conventional processes; advanced nonaqueous reprocessing is also considered. This contribution provides a comprehensive data base for evaluation of proliferation risks

  8. Reactor Materials Program: Mechanical properties of irradiated Types 304 and 304L stainless steel weldment components

    International Nuclear Information System (INIS)

    The vessels (reactor tanks) of the Savannah River Site nuclear production reactors constructed in the 1950's are comprised of Type 304 stainless steel with Type 308 stainless steel weld filler. Irradiation exposure to the reactor tank sidewalls through reactor operation has caused a change in the mechanical properties of these materials. A database of as-irradiated mechanical properties for site-specific materials and irradiation conditions has been produced for reactor tank structural analyses and to quantify the effects of radiation-induced materials degradation for evaluating reactor service life. The data has been collected from the SRL Reactor Materials Program (RMP) irradiations and testing of archival stainless steel weldment components and from previous SRL programs to measure properties of irradiated reactor Thermal Shield weldments and reactor tank (R-tank) sidewall material. Irradiation programs of the RMP are designed to quantify mechanical properties at tank operating temperatures following irradiation to present and future tank wall maximum exposure conditions. The exposure conditions are characterized in terms of fast neutron fluence (En > 0.1 MeV) and displacements per atom (dpa)3. Tensile properties, Charpy-V notch toughness, and elastic-plastic fracture toughness were measured for base, weld, and weld heat-affected zone (HAZ) weldment components from archival piping specimens following a Screening Irradiation in the University of Buffalo Reactor (UBR) and following a Full-Term Irradiation in the High Flux Isotope Reactor (HFIR)

  9. Reactor Materials Program: Mechanical properties of irradiated Types 304 and 304L stainless steel weldment components

    Energy Technology Data Exchange (ETDEWEB)

    Sindelar, R.L.; Caskey, G.R. Jr.

    1991-12-01

    The vessels (reactor tanks) of the Savannah River Site nuclear production reactors constructed in the 1950's are comprised of Type 304 stainless steel with Type 308 stainless steel weld filler. Irradiation exposure to the reactor tank sidewalls through reactor operation has caused a change in the mechanical properties of these materials. A database of as-irradiated mechanical properties for site-specific materials and irradiation conditions has been produced for reactor tank structural analyses and to quantify the effects of radiation-induced materials degradation for evaluating reactor service life. The data has been collected from the SRL Reactor Materials Program (RMP) irradiations and testing of archival stainless steel weldment components and from previous SRL programs to measure properties of irradiated reactor Thermal Shield weldments and reactor tank (R-tank) sidewall material. Irradiation programs of the RMP are designed to quantify mechanical properties at tank operating temperatures following irradiation to present and future tank wall maximum exposure conditions. The exposure conditions are characterized in terms of fast neutron fluence (E{sub n} > 0.1 MeV) and displacements per atom (dpa){sup 3}. Tensile properties, Charpy-V notch toughness, and elastic-plastic fracture toughness were measured for base, weld, and weld heat-affected zone (HAZ) weldment components from archival piping specimens following a Screening Irradiation in the University of Buffalo Reactor (UBR) and following a Full-Term Irradiation in the High Flux Isotope Reactor (HFIR).

  10. Reactor Materials Program: Mechanical properties of irradiated Types 304 and 304L stainless steel weldment components

    Energy Technology Data Exchange (ETDEWEB)

    Sindelar, R.L.; Caskey, G.R. Jr.

    1991-12-01

    The vessels (reactor tanks) of the Savannah River Site nuclear production reactors constructed in the 1950`s are comprised of Type 304 stainless steel with Type 308 stainless steel weld filler. Irradiation exposure to the reactor tank sidewalls through reactor operation has caused a change in the mechanical properties of these materials. A database of as-irradiated mechanical properties for site-specific materials and irradiation conditions has been produced for reactor tank structural analyses and to quantify the effects of radiation-induced materials degradation for evaluating reactor service life. The data has been collected from the SRL Reactor Materials Program (RMP) irradiations and testing of archival stainless steel weldment components and from previous SRL programs to measure properties of irradiated reactor Thermal Shield weldments and reactor tank (R-tank) sidewall material. Irradiation programs of the RMP are designed to quantify mechanical properties at tank operating temperatures following irradiation to present and future tank wall maximum exposure conditions. The exposure conditions are characterized in terms of fast neutron fluence (E{sub n} > 0.1 MeV) and displacements per atom (dpa){sup 3}. Tensile properties, Charpy-V notch toughness, and elastic-plastic fracture toughness were measured for base, weld, and weld heat-affected zone (HAZ) weldment components from archival piping specimens following a Screening Irradiation in the University of Buffalo Reactor (UBR) and following a Full-Term Irradiation in the High Flux Isotope Reactor (HFIR).

  11. A review of fast reactor program in Japan (April 2001 - March 2002)

    International Nuclear Information System (INIS)

    This report describes the research and development activities on fast reactors in Japan thru April 2001 to March 2002. In December 2001, the Cabinet decided the Plan for Reorganization of Government-funded Corporations including the merger of JNC and the Japan Atomic Energy Research Institute (JAERI). A law to set up a new entity is supposed to be submitted to the National Diet by the Japanese Fiscal Year (JFY) 2004. In the Experimental Fast Reactor Joyo, thirty-five duty cycle operations and thirteen special tests with the MK-II core were completed by June 2000 without any fuel pin failures or serious plant trouble. The reactor is currently being upgraded to the MK-III core. Though a fire broke out in the maintenance building of Joyo in October 2001, the Mk-III construction work was restarted in February 2002. In the Prototype Fast Breeder Reactor Monju, countermeasures against sodium leakage have already been drawn up based on Monju comprehensive safety review. The safety licensing examination for the plant modification of Monju is undergoing. As for the Feasibility Study on Commercialized Fast Reactor Cycle Systems, JFY2001 was the first year of its second phase. A three-year period from JFY2001 to 2003 is the initial term of this phase. During this term, research activities are being focused on the design of the candidate concepts and fundamental tests of key technologies. An interim summary of these activities will be checked and reviewed, and based on the results; the research for JFY 2004 to 2005 will be conducted in order to narrow down the number of alternatives for the fast reactor cycle. (author)

  12. Status of reduced enrichment programs for research reactors in Japan

    Energy Technology Data Exchange (ETDEWEB)

    Kanda, Keiji; Nishihara, Hedeaki [Kyoto Univ., Osaka (Japan); Shirai, Eiji; Oyamada, Rokuro; Sanokawa, Konomo [Japan Atomic Energy Research Institute, Tokyo (Japan)

    1997-08-01

    The reduced enrichment programs for the JRR-2, JRR-3, JRR-4 and JMTR of Japan Atomic Energy Research Institute (JAERI), and the KUR of Kyoto University Research Reactor Institute (KURRI) have been partially completed and are mostly still in progress under the Joint Study Programs with Argonne National Laboratory (ANL). The JMTR and JRR-2 have been already converted to use MEU aluminide fuels in 1986 and 1987, respectively. The operation of the upgraded JRR-3(JRR-3M) has started in March 1990 with the LEU aluminide fuels. Since May 1992, the two elements have been inserted in the KUR. The safety review application for the full core conversion to use LEU silicide in the JMTR was approved in February 1992 and the conversion has been done in January 1994. The Japanese Government approved a cancellation of the KUHFR Project in February 1991, and in April 1994 the U.S. Government gave an approval to utilize HEU in the KUR instead of the KUHFR. Therefore, the KUR will be operated with HEU fuel until 2001. Since March 1994, Kyoto University is continuing negotiation with UKAEA Dounreay on spent fuel reprocessing and blending down of recovered uranium, in addition to that with USDOE.

  13. Status of reduced enrichment programs for research reactors in Japan

    International Nuclear Information System (INIS)

    The reduced enrichment programs for the JRR-2, JRR-3, JRR-4 and JMTR of Japan Atomic Energy Research Institute (JAERI), and the KUR of Kyoto University Research Reactor Institute (KURRI) have been partially completed and are mostly still in progress under the Joint Study Programs with Argonne National Laboratory (ANL). The JMTR and JRR-2 have been already converted to use MEU aluminide fuels in 1986 and 1987, respectively. The operation of the upgraded JRR-3(JRR-3M) has started in March 1990 with the LEU aluminide fuels. Since May 1992, the two elements have been inserted in the KUR. The safety review application for the full core conversion to use LEU silicide in the JMTR was approved in February 1992 and the conversion has been done in January 1994. The Japanese Government approved a cancellation of the KUHFR Project in February 1991, and in April 1994 the U.S. Government gave an approval to utilize HEU in the KUR instead of the KUHFR. Therefore, the KUR will be operated with HEU fuel until 2001. Since March 1994, Kyoto University is continuing negotiation with UKAEA Dounreay on spent fuel reprocessing and blending down of recovered uranium, in addition to that with USDOE

  14. New progress on design and R and D for solid breeder test blanket module in China

    Energy Technology Data Exchange (ETDEWEB)

    Feng, K.M., E-mail: fengkm@swip.ac.cn; Zhang, G.S.; Hu, G.; Chen, Y.J.; Feng, Y.J.; Li, Z.X.; Wang, P.H.; Zhao, Z.; Ye, X.F.; Xiang, B.; Zhang, L.; Wang, Q.J.; Cao, Q.X.; Zhao, F.C.; Wang, F.; Liu, Y.; Zhang, M.C.

    2014-10-15

    Highlights: • The new progress on design and R and D of Chinese solid breeder TBM are introduced. • The mock-up fabrication and component tests for Chinese HCCB TBM have being developed. • The neutron multiplier Be pebbles, tritium breeder Li{sub 4}SiO{sub 4} pebbles, and structure material CFL-1 are being prepared. • The fabrication of 1/3 sized mock-up is being carried-out. • The key technology development is proceeding to the large-scale mock-up fabrication. - Abstract: ITER will be used to test tritium breeding module concepts, which will lead to the design of DEMO fusion reactor demonstrating tritium self-sufficiency and the extraction of high grade heat for electricity production. China plans to test the HCCB TBM modules during different operation phases. Related design and R and D activities for each TBM module with the auxiliary system are introduced. The helium-cooled ceramic breeder (HCCB) test blanket module (TBM) is the primary option of the Chinese TBM program. The preliminary conceptual design of CN HCCB TBM has been completed. A modified design to reduce the RAFM material mass to 1.3 ton has been carried out based on the ITER technical requirement. Basic characteristics and main design parameters of CN HCCB TBM are introduced briefly. The mock-up fabrication and component tests for Chinese test blanket module are being developed. Recent status of the components of CN HCCB TBM and fabrication technology development are also reported. The neutron multiplier Be pebbles, tritium breeder Li{sub 4}SiO{sub 4} pebbles, and structure material CLF-1 of ton-class are being prepared in laboratory scale. The fabrication of pebble bed container and experiment of tritium breeder pebble bed will be started soon. The fabrication technology development is proceeding as the large-scale mock-up fabrication enters into the R and D stage and demonstration tests toward TBM testing on ITER test port are being done as scheduled.

  15. Fast reactor development program in France in 1997

    International Nuclear Information System (INIS)

    , in spite of the availability of one and half core. This decision leads to drop the >. The Capra program was reoriented. Now, emphasis is put on burning the minor actinides (MA) and long-lived fusion products (LLFP), which answers the French 1991 law on radioactive wastes; as a consequence, the experimental programme proposed for Phenix is mainly devoted to this objective. This report presents also the status of Rapsodie, and the main achievements on the R and D programme on fast reactors. (author)

  16. Light Water Reactor Sustainability Program. Digital Architecture Requirements

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Kenneth [Idaho National Lab. (INL), Idaho Falls, ID (United States); Oxstrand, Johanna [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-03-01

    The Digital Architecture effort is a part of the Department of Energy (DOE) sponsored Light-Water Reactor Sustainability (LWRS) Program conducted at Idaho National Laboratory (INL). The LWRS program is performed in close collaboration with industry research and development (R&D) programs that provides the technical foundations for licensing and managing the long-term, safe, and economical operation of current nuclear power plants (NPPs). One of the primary missions of the LWRS program is to help the U.S. nuclear industry adopt new technologies and engineering solutions that facilitate the continued safe operation of the plants and extension of the current operating licenses. Therefore, a major objective of the LWRS program is the development of a seamless digital environment for plant operations and support by integrating information from plant systems with plant processes for nuclear workers through an array of interconnected technologies. In order to get the most benefits of the advanced technology suggested by the different research activities in the LWRS program, the nuclear utilities need a digital architecture in place to support the technology. A digital architecture can be defined as a collection of information technology (IT) capabilities needed to support and integrate a wide-spectrum of real-time digital capabilities for nuclear power plant performance improvements. It is not hard to imagine that many processes within the plant can be largely improved from both a system and human performance perspective by utilizing a plant wide (or near plant wide) wireless network. For example, a plant wide wireless network allows for real time plant status information to easily be accessed in the control room, field workers’ computer-based procedures can be updated based on the real time plant status, and status on ongoing procedures can be incorporated into smart schedules in the outage command center to allow for more accurate planning of critical tasks. The goal

  17. Fast-Mixed Spectrum Reactor. Progress report for 1979

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, G.J.; Cerbone, R.J.

    1980-05-01

    This report summarizes the progress of the Fast Mixed Spectrum Reactor (FMSR) since the publication of the Interim Report in January 1979. The FMSR program was initiated to determine the feasibility of a breeder reactor concept which operated on a once-through-and-store fuel cycle and for which the only feed would be natural uranium. A first or startup core enriched to a maximum of about eleven percent in uranium-235 would be required. The concept has excellent antiproliferation advantages. In the once-through and store mode, the FMSR has a resource utilization which is a factor of four higher than a light water reactor.

  18. Fast-Mixed Spectrum Reactor. Progress report for 1979

    International Nuclear Information System (INIS)

    This report summarizes the progress of the Fast Mixed Spectrum Reactor (FMSR) since the publication of the Interim Report in January 1979. The FMSR program was initiated to determine the feasibility of a breeder reactor concept which operated on a once-through-and-store fuel cycle and for which the only feed would be natural uranium. A first or startup core enriched to a maximum of about eleven percent in uranium-235 would be required. The concept has excellent antiproliferation advantages. In the once-through and store mode, the FMSR has a resource utilization which is a factor of four higher than a light water reactor

  19. Chemical operational experience with the water/steam-circuit at KNK II; Presentation at the meeting on Experience exchange on operational experience of fast breeder reactors, Karlsruhe/Bensberg/Kalkar, June 18. - 22. 1990

    International Nuclear Information System (INIS)

    The availability of sodium cooled reactors depends essentially from the safety and reliability of the sodium heated steam generator. The transition from experimental plants with 12-20 MW electrical power to larger plants with 600 MW (BN-600) or 1200 MW (Superphenix) required the change from modular components to larger and compact steam generators with up to 800 MW. Defects of these large components cause extreme losses in availability of the plant and have to be avoided. In view of this request, a comprehensive test program has been performed at KNK II in addition to the normal control of the water/steam-circuit to compile all operational data on the water and steam side of the sodium heated steam generator. This paper describes the plant and the water/steam-circuit with its mode of operation. The experience with the surveillance and different methods of the conditioning are discussed in detail in this presentation

  20. Participation in the U.S. Department of Energy Reactor Sharing Program. Progress report

    International Nuclear Information System (INIS)

    The objective of the DOE supported Reactor Sharing Program is to increase the availability of university nuclear reactor facilities to non-reactor-owning educational institutions. The educational and research programs of these user institutions is enhanced by the use of the nuclear facilities. Several methods have been used by the UVA Reactor Facility to achieve this objective. First, many college and secondary school groups toured the Reactor Facility and viewed the UVAR reactor and associated experimental facilities. Second, advanced undergraduate and graduate classes from area colleges and universities visited the facility to perform experiments in nuclear engineering and physics which would not be possible at the user institution. Third, irradiation and analysis services at the Facility have been made available for research by faculty and students from user institutions. Fourth, some institutions have received activated material from UVA for use at their institutions. These areas are discussed here

  1. Participation in the U.S. Department of Energy Reactor Sharing Program. Progress report

    Energy Technology Data Exchange (ETDEWEB)

    Mulder, R.U.; Benneche, P.E.; Hosticka, B.

    1997-03-01

    The objective of the DOE supported Reactor Sharing Program is to increase the availability of university nuclear reactor facilities to non-reactor-owning educational institutions. The educational and research programs of these user institutions is enhanced by the use of the nuclear facilities. Several methods have been used by the UVA Reactor Facility to achieve this objective. First, many college and secondary school groups toured the Reactor Facility and viewed the UVAR reactor and associated experimental facilities. Second, advanced undergraduate and graduate classes from area colleges and universities visited the facility to perform experiments in nuclear engineering and physics which would not be possible at the user institution. Third, irradiation and analysis services at the Facility have been made available for research by faculty and students from user institutions. Fourth, some institutions have received activated material from UVA for use at their institutions. These areas are discussed here.

  2. PODESY program for flux mapping of CNA II reactor:

    International Nuclear Information System (INIS)

    The PODESY program, developed by KWU, calculates the spatial flux distribution of CNA II reactor through a three-dimensional expansion of 90 incore detector measurements. The calculation is made in three steps: a) short-term calculation which considers the control rod positions and it has to be done each time the flux mapping is calculated; b) medium-term calculation which includes local burn-up dependent calculation made by diffusion methods in macro-cell configurations (seven channels in hexagonal distribution), and c) long-term calculation, or macroscopic flux determination, that is a fitting and expansion of measured fluxes, previously corrected by local effects, using the eigen functions of the modified diffusion equation. The paper outlines development of step (c) of the calculation. The incore detectors have been located in the central zone of the core. In order to obtain low errors in the expansion procedure it is necessary to include additional points, whose flux values are assumed to be equivalent to detector measurements. These flux values are calculated with detector measurements and a spatial flux distribution calculated by a PUMA code. This PUMA calculation employs a smooth burn-up distribution (local burn-up variations are considered in step (b) of the whole calculation) representing the state of core evolution at the calculation time. The core evolution referred to ends when the equilibrium core condition is reached. Additionally, a calculation method to be employed in the plant in case of incore detector failures, is proposed. (Author)

  3. Final report. U.S. Department of Energy University Reactor Sharing Program

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, John A

    2003-01-21

    Activities supported at the MIT Nuclear Reactor Laboratory under the U.S. DOE University Reactor Sharing Program are reported for Grant DE FG02-95NE38121 (September 16, 1995 through May 31, 2002). These activities fell under four subcategories: support for research at thesis and post-doctoral levels, support for college-level laboratory exercises, support for reactor tours/lectures on nuclear energy, and support for science fair participants.

  4. Final report. U.S. Department of Energy University Reactor Sharing Program

    International Nuclear Information System (INIS)

    Activities supported at the MIT Nuclear Reactor Laboratory under the U.S. DOE University Reactor Sharing Program are reported for Grant DE FG02-95NE38121 (September 16, 1995 through May 31, 2002). These activities fell under four subcategories: support for research at thesis and post-doctoral levels, support for college-level laboratory exercises, support for reactor tours/lectures on nuclear energy, and support for science fair participants

  5. Advanced reactor safety research quarterly report, October-December 1982. Volume 24

    Energy Technology Data Exchange (ETDEWEB)

    None

    1984-04-01

    This report describes progress in a number of activities dealing with current safety issues relevant to both light water reactors (LWRs) and breeder reactors. The work includes a broad range of experiments to simulate accidental conditions to provide the required data base to understand important accident sequences and to serve as a basis for development and verification of the complex computer simulation models and codes used in accident analysis and licensing reviews. Such a program must include the development of analytical models, verified by experiment, which can be used to predict reactor and safety system performance under a broad variety of abnormal conditions. Current major emphasis is focused on providing information to NRC relevant to (1) its deliberations and decisions dealing with severe LWR accidents and (2) its safety evaluation of the proposed Clinch River Breeder Reactor.

  6. Magnetic Fustion Reactor Design Studies Program final report, 1 July 1986--30 September 1986

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-09-30

    This report presents progress reported during the period, 7/1/86 - 9/30/86 for the Technical Support Services (TSS) for the Magnetic Fusion Reactor Design Studies Program. Tasks reported include: systems studies work plan, normalization of reactor design studies, interpretation of design study activities, research and development plan, conference support, and reports generated.

  7. Analysis of Time-Dependent Tritium Breeding Capability of Water Cooled Ceramic Breeder Blanket for CFETR

    Science.gov (United States)

    Gao, Fangfang; Zhang, Xiaokang; Pu, Yong; Zhu, Qingjun; Liu, Songlin

    2016-08-01

    Attaining tritium self-sufficiency is an important mission for the Chinese Fusion Engineering Testing Reactor (CFETR) operating on a Deuterium-Tritium (D-T) fuel cycle. It is necessary to study the tritium breeding ratio (TBR) and breeding tritium inventory variation with operation time so as to provide an accurate data for dynamic modeling and analysis of the tritium fuel cycle. A water cooled ceramic breeder (WCCB) blanket is one candidate of blanket concepts for the CFETR. Based on the detailed 3D neutronics model of CFETR with the WCCB blanket, the time-dependent TBR and tritium surplus were evaluated by a coupling calculation of the Monte Carlo N-Particle Transport Code (MCNP) and the fusion activation code FISPACT-2007. The results indicated that the TBR and tritium surplus of the WCCB blanket were a function of operation time and fusion power due to the Li consumption in breeder and material activation. In addition, by comparison with the results calculated by using the 3D neutronics model and employing the transfer factor constant from 1D to 3D, it is noted that 1D analysis leads to an over-estimation for the time-dependent tritium breeding capability when fusion power is larger than 1000 MW. supported by the National Magnetic Confinement Fusion Science Program of China (Nos. 2013GB108004, 2015GB108002, and 2014GB119000), and by National Natural Science Foundation of China (No. 11175207)

  8. IAMBUS, a computer code for the design and performance prediction of fast breeder fuel rods

    International Nuclear Information System (INIS)

    IAMBUS is a computer code for the thermal and mechanical design, in-pile performance prediction and post-irradiation analysis of fast breeder fuel rods. The code deals with steady, non-steady and transient operating conditions and enables to predict in-pile behavior of fuel rods in power reactors as well as in experimental rigs. Great effort went into the development of a realistic account of non-steady fuel rod operating conditions. The main emphasis is placed on characterizing the mechanical interaction taking place between the cladding tube and the fuel as a result of contact pressure and friction forces, with due consideration of axial and radial crack configuration within the fuel as well as the gradual transition at the elastic/plastic interface in respect to fuel behavior. IAMBUS can be readily adapted to various fuel and cladding materials. The specific models and material correlations of the reference version deal with the actual in-pile behavior and physical properties of the KNK II and SNR 300 related fuel rod design, confirmed by comparison of the fuel performance model with post-irradiation data. The comparison comprises steady, non-steady and transient irradiation experiments within the German/Belgian fuel rod irradiation program. The code is further validated by comparison of model predictions with post-irradiation data of standard fuel and breeder rods of Phenix and PFR as well as selected LWR fuel rods in non-steady operating conditions

  9. Study of mechanisms and kinetics of Sodium-CO2 interactions. Contribution to the evaluation of an energy conversion system with supercritical CO2 for sodium fast breeder reactors

    International Nuclear Information System (INIS)

    This PhD study consisted in studying reactive mechanisms and kinetics of sodium-CO2 interactions, in the frame of the assessment of an energy conversion system with supercritical CO2 for fast breeder reactors cooled by sodium. The approach was the following. First of all, the interactions between sodium and CO2 have been brought to light by laboratory experiments associated with products analysis. They have enabled the establishment of a coherent mechanism, in agreement with literature data, and gave preliminary indications on the reaction kinetics. In order to estimate a more detailed reaction kinetics, we tried to approach the phenomenon that appears in the case of a leak in a sodium-CO2 heat exchanger. Geometry of such heat exchangers is not fixed for the moment, even if the development of compact exchangers is foreseen. Then, free jets of CO2 in liquid sodium have been modeled in order to obtain, by identification, kinetics parameters of the reaction. Those parameters, estimated with such a geometry, will remain valid with a much complex geometry, that will better represent the real exchanger. An experimental bench has been defined and built to realize those jets. The first laboratory experiments have concluded in the existence of different reactive mechanisms according to the temperature level. A threshold has been brought to light around 500 C. Below this one, reaction appears moderated, or even, slow, with a medium exothermicity, and appears after an induction period that depends on the temperature,and which duration could reach several hours. At contrary, above this threshold, it seems rapid and more exothermic. Below 500 C, sodium oxalate is produced, and then reacts with sodium in an exothermic way, following the reactions: CO2 + Na →1/4 Na2C2O4 + 1/4 CO + 1/4 Na2CO3 (5) 4 Na + Na2C2O4 → 3 Na2O + CO + C (6) Above 500 C, sodium carbonate is produced, and can then possibly react with sodium in an endothermic way, following the reactions: 4 Na + 3 CO2

  10. 3. Interindustry conference on reactor materials science

    International Nuclear Information System (INIS)

    This document contains abstracts on papers presented at the Third Interindustry Conference on Reactor Materials Science (Dimitrovgrad, 27-30 October 1992). The subject scope of the papers is a follows: fuel and fuel elements of power reactors; structural materials of fast breeder reactors and thermonuclear reactors; structural materials of WWER and RBMK type reactors; absorbers and moderators

  11. Development of Solid Breeder Blanket at JAERI

    International Nuclear Information System (INIS)

    Japan Atomic Energy Research Institute (JAERI) has been performing blanket development based on the long-term research program of fusion blankets in Japan, which was approved by the Fusion Council of Japan in 1999. The blanket development consists of out-pile R and D, In-pile R and D, TBM Neutronics and TPR Tests and Tritium Recovery System R and D. Based on the achievements of element technology development, the R and D program is now stepping to the engineering testing phase, in which scalable mockup tests will be performed for obtaining engineering data unique to the specific structure of the components, with the objective to define the fabrication specification of test blanket modules for ITER. This paper presents the major achievements of the element technology development of solid breeder blanket in JAERI

  12. Irradiation testing of miniature fuel plates for the RERTR program. [Reduced Enrichment Research and Test Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Senn, R.L.; Martin, M.M.

    1981-07-01

    An irradiation test facility, which provides a test bed for irradiating a variety of miniature fuel plates (miniplates) for the Reduced Enrichment Research and Test Reactors (RERTR) program, has been placed into operation. These tests screen various candidate fuel materials on their suitability for replacing the highly enriched uranium fuel materials currently used by the world's test and research reactors with a lower enrichment fuel material, without significantly degrading reactor operating characteristics and power levels. The use of low uranium enrichment of about 20% /sup 235/U in place of highly enriched fuel for these reactors would reduce the potential for /sup 235/U diversion. The irradiation test facility, designated as HFED, is operating in core position E-7 in the Oak Ridge Research Reactor (ORR), a 30-MW water-moderated reactor. The miniplates will achieve burnups of up to approx. 2.2 x 10/sup 27/ fissions/m/sup 3/ of fuel.

  13. Sodium components cleaning status in the Italian fast reactor program

    International Nuclear Information System (INIS)

    As a consequence of the Italian Fast Reactor Development, mainly aimed to the PEC project and to the participation in the French Superphenix project, it is of increasing importance to set up a reliable method for specific reactor components and related test loops. The first problem was the cleaning of the PEC fuelling machine. In order to perform the routine maintenance of the machine an alcohol cleaning method based on the use of 2-butoxyethanol-NN dimethylformamide mixture has been proposed

  14. Application of the REMIX thermal mixing calculation program for the Loviisa reactor

    International Nuclear Information System (INIS)

    The REMIX computer program has been validated to be used in the pressurized thermal shock study of the Loviisa reactor pressure vessel. The program has been verified against the data from the thermal and fluid mixing experiments. These experiments have been carried out in Imatran voima Oy to study thermal mixing of the high-pressure safety injection water in the Loviisa VVER-440 type pressurized water reactor. The verified REMIX-versions were applied to reactor calculations in the probabilistic pressurized thermal shock study of the Loviisa Plant

  15. Roadmap for Nondestructive Evaluation of Reactor Pressure Vessel Research and Development by the Light Water Reactor Sustainability Program

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Cyrus M [ORNL; Nanstad, Randy K [ORNL; Clayton, Dwight A [ORNL; Matlack, Katie [Georgia Institute of Technology; Ramuhalli, Pradeep [Pacific Northwest National Laboratory (PNNL); Light, Glenn [Southwest Research Institute, San Antonio

    2012-09-01

    The Department of Energy s (DOE) Light Water Reactor Sustainability (LWRS) Program is a five year effort which works to develop the fundamental scientific basis to understand, predict, and measure changes in materials and systems, structure, and components as they age in environments associated with continued long-term operations of existing commercial nuclear power reactors. This year, the Materials Aging and Degradation (MAaD) Pathway of this program has placed emphasis on emerging Non-Destructive Evaluation (NDE) methods which support these objectives. DOE funded Research and Development (R&D) on emerging NDE techniques to support commercial nuclear reactor sustainability is expected to begin next year. This summer, the MAaD Pathway invited subject matter experts to participate in a series of workshops which developed the basis for the research plan of these DOE R&D NDE activities. This document presents the results of one of these workshops which are the DOE LWRS NDE R&D Roadmap for Reactor Pressure Vessels (RPV). These workshops made a substantial effort to coordinate the DOE NDE R&D with that already underway or planned by the Electric Power Research Institute (EPRI) and the Nuclear Regulatory Commission (NRC) through their representation at these workshops.

  16. 78 FR 63516 - Initial Test Program of Emergency Core Cooling Systems for New Boiling-Water Reactors

    Science.gov (United States)

    2013-10-24

    ... COMMISSION Initial Test Program of Emergency Core Cooling Systems for New Boiling-Water Reactors AGENCY... Cooling Systems for New Boiling-Water Reactors.'' This RG describes testing methods the NRC staff...)-1277, ``Initial Test Program of Emergency Core Cooling Systems for Boiling-Water Reactors.''...

  17. Conceptual design of a water cooled breeder blanket for CFETR

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Songlin, E-mail: slliu@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Pu, Yong; Cheng, Xiaoman [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Li, Jia; Peng, ChangHong [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230027 (China); Ma, Xuebing [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Chen, Lei [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230027 (China)

    2014-10-15

    Highlights: • We proposed a water cooled ceramic breeder blanket with superheated steam. • Superheated steam is generated at the first wall and the front part of breeder zone. • Superheated steam has negligible impact on neutron absorption by coolant in FW and improves TBR. • The superheated steam at higher temperature can improve thermal efficiency. - Abstract: China Fusion Engineering Test Reactor (CFETR) is an ITER-like superconducting tokamak reactor. Its major radius is 5.7 m, minor radius is 1.6 m and elongation ratio is 1.8. Its mission is to achieve 50–200 MW of fusion power, 30–50% of duty time factor, and tritium breeding ratio not less than 1.2 to ensure the self-sufficiency. As one of the breeding blanket candidates for CFETR, a water cooled breeder blanket with superheated steam is proposed and its conceptual design is being carried out. In this design, sub-cooling water at 265 °C under the pressure of 7 MPa is fed into cooling plates in breeding zone and is heated up to 285 °C with saturated steam generated, and then this steam is pre-superheated up to 310 °C in first wall (FW), final, the pre-superheated steam coming from several blankets is fed into the other one blanket to superheat again up to 517 °C. Due to low density of superheated steam, it has negligible impact on neutron absorption by coolant in FW so that the high energy neutrons entering into breeder zone moderated by water in cooling plate help enhance tritium breeding by {sup 6}Li(n,α)T reaction. Li{sub 2}TiO{sub 3} pebbles and Be{sub 12}Ti pebbles are chosen as tritium breeder and neutron multiplier respectively, because Li{sub 2}TiO{sub 3} and Be{sub 12}Ti are expected to have better chemical stability and compatibility with water in high temperature. However, Be{sub 12}Ti may lead to a reduction in tritium breeding ratio (TBR). Furthermore, a spot of sintered Be plate is used to improve neutron multiplying capacity in a multi-layer structure. As one alternative option

  18. Conceptual design of a water cooled breeder blanket for CFETR

    International Nuclear Information System (INIS)

    Highlights: • We proposed a water cooled ceramic breeder blanket with superheated steam. • Superheated steam is generated at the first wall and the front part of breeder zone. • Superheated steam has negligible impact on neutron absorption by coolant in FW and improves TBR. • The superheated steam at higher temperature can improve thermal efficiency. - Abstract: China Fusion Engineering Test Reactor (CFETR) is an ITER-like superconducting tokamak reactor. Its major radius is 5.7 m, minor radius is 1.6 m and elongation ratio is 1.8. Its mission is to achieve 50–200 MW of fusion power, 30–50% of duty time factor, and tritium breeding ratio not less than 1.2 to ensure the self-sufficiency. As one of the breeding blanket candidates for CFETR, a water cooled breeder blanket with superheated steam is proposed and its conceptual design is being carried out. In this design, sub-cooling water at 265 °C under the pressure of 7 MPa is fed into cooling plates in breeding zone and is heated up to 285 °C with saturated steam generated, and then this steam is pre-superheated up to 310 °C in first wall (FW), final, the pre-superheated steam coming from several blankets is fed into the other one blanket to superheat again up to 517 °C. Due to low density of superheated steam, it has negligible impact on neutron absorption by coolant in FW so that the high energy neutrons entering into breeder zone moderated by water in cooling plate help enhance tritium breeding by 6Li(n,α)T reaction. Li2TiO3 pebbles and Be12Ti pebbles are chosen as tritium breeder and neutron multiplier respectively, because Li2TiO3 and Be12Ti are expected to have better chemical stability and compatibility with water in high temperature. However, Be12Ti may lead to a reduction in tritium breeding ratio (TBR). Furthermore, a spot of sintered Be plate is used to improve neutron multiplying capacity in a multi-layer structure. As one alternative option, in spite of lower TBR, Pb is taken into

  19. Flow Induced Vibration Program at Argonne National Laboratory

    International Nuclear Information System (INIS)

    Argonne National Laboratory has had a Flow Induced Vibration Program since 1967; the Program currently resides in the Laboratory's Components Technology Division. Throughout its existence, the overall objective of the program has been to develop and apply new and/or improved methods of analysis and testing for the design evaluation of nuclear reactor plant components and heat exchange equipment from the standpoint of flow induced vibration. Historically, the majority of the program activities have been funded by the US Atomic Energy Commission (AEC), Energy Research and Development Administration (ERDA), and Department of Energy (DOE). Current DOE funding is from the Breeder Mechanical Component Development Division, Office of Breeder Technology Projects; Energy Conversion and Utilization Technology (ECUT) Program, Office of Energy Systems Research; and Division of Engineering, Mathematical and Geosciences, Office of Basic Energy Sciences. Testing of Clinch River Breeder Reactor upper plenum components has been funded by the Clinch River Breeder Reactor Plant (CRBRP) Project Office. Work has also been performed under contract with Foster Wheeler, General Electric, Duke Power Company, US Nuclear Regulatory Commission, and Westinghouse

  20. Flow Induced Vibration Program at Argonne National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    1984-01-01

    Argonne National Laboratory has had a Flow Induced Vibration Program since 1967; the Program currently resides in the Laboratory's Components Technology Division. Throughout its existence, the overall objective of the program has been to develop and apply new and/or improved methods of analysis and testing for the design evaluation of nuclear reactor plant components and heat exchange equipment from the standpoint of flow induced vibration. Historically, the majority of the program activities have been funded by the US Atomic Energy Commission (AEC), Energy Research and Development Administration (ERDA), and Department of Energy (DOE). Current DOE funding is from the Breeder Mechanical Component Development Division, Office of Breeder Technology Projects; Energy Conversion and Utilization Technology (ECUT) Program, Office of Energy Systems Research; and Division of Engineering, Mathematical and Geosciences, Office of Basic Energy Sciences. Testing of Clinch River Breeder Reactor upper plenum components has been funded by the Clinch River Breeder Reactor Plant (CRBRP) Project Office. Work has also been performed under contract with Foster Wheeler, General Electric, Duke Power Company, US Nuclear Regulatory Commission, and Westinghouse.

  1. Pilot program: NRC severe reactor accident incident response training manual: Severe reactor accident overview

    International Nuclear Information System (INIS)

    This pilot training manual has been written to fill the need for a general text on NRC response to reactor accidents. The manual is intended to be the foundation for a course for all NRC response personnel. Severe Reactor Accident Overview is the second in a series of volumes that collectively summarize the US Nuclear Regulatory Commission (NRC) emergency response during severe power reactor accidents and provide necessary background information. This volume describes elementary perspectives on severe accidents and accident assesment. Each volume serves, respectively, as the text for a course of instruction in a series of courses. Each volume is accompanied by an appendix of slides that can be used to present this material. The slides are called out in the text

  2. Reactor Safety Research: Semiannual report, January-June 1986: Reactor Safety Research Program

    Energy Technology Data Exchange (ETDEWEB)

    1987-05-01

    Sandia National Laboratories is conducting, under USNRC sponsorship, phenomenological research related to the safety of commercial nuclear power reactors. The research includes experiments to simulate the phenomenology of accident conditions and the development of analytical models, verified by experiment, which can be used to predict reactor and safety systems performance behavior under abnormal conditions. The objective of this work is to provide NRC requisite data bases and analytical methods to (1) identify and define safety issues, (2) understand the progression of risk-significant accident sequences, and (3) conduct safety assessments. The collective NRC-sponsored effort at Sandia National Laboratories is directed at enhancing the technology base supporting licensing decisions.

  3. Current status on fast reactor program in Kazakhstan

    International Nuclear Information System (INIS)

    Kazakhstan Atomic Scientific and Industrial Complex consists of uranium mining, fuel production, and power industry. On the territory of the former Semipalatinsk Nuclear Test Site, there are three research reactors (EWG-1M, thermal light water heterogeneous vessel reactor with light water moderator and coolant, beryllium reflector, maximum thermal power, 35 MW, 4 hours period of continuous operation at maximum power; IGR, impulse homogeneous uranium-graphite thermal reactor with graphite reflector, maximum heat release is 5.2 GJ (1 GJ in a pulse), maximum thermal neutron flux is 0.7*1017 cm-2s-1; RA, about 0.5 MW thermal high temperature heterogeneous reactor with air coolant, zirconium hydride moderator, and beryllium reflector), and one non-reactor test facility (EAGLE, reactor fuel element melting testing). One research reactor and sub-critical assembly near Almaty (VVR-K, 10 MW light water reactor) is used primarily for nuclear safety investigations. Following a Presidential decree, Kazakhstan will establish the following technology centres: Centre of Information Technologies, based at the Nuclear Physics Institute in Altau; Centre of Biotechnologies, based at the former military centre in Stepnogorsk; and the Centre of Nuclear Technologies, based at the National Nuclear Centre in Kurchatov City. The experimental reactor TOKOMAK will be constructed at Kurchatov City in support of the International Thermonuclear Experimental Reactor (ITER) project. Works have already started. The General Plan for the BN-350 decommissioning was developed within the framework of a Kazakh - US project. At the end of March 2003, the Plan was presented for final review to a IAEA group of experts. Due to a new US DOE initiative, of the Feasibility Study Report on the possibility to use 120 t metal-concrete casks for BN-350 spent fuel transportation and long-term storage was performed at the end of 2002. These casks shall be designed and manufactured in Russia. The content (NaK) of the

  4. Advanced reactors transition fiscal year 1995 multi-year program plan WBS 7.3

    International Nuclear Information System (INIS)

    This document describes in detail the work to be accomplished in FY-1995 and the out years for the Advanced Reactors Transition (WBS 7.3). This document describes specific milestones and funding profiles. Based upon the Fiscal Year 1995 Multi-Year Program Plan, DOE will provide authorization to perform the work outlined in the FY 1995 MYPP. Following direction given by the US Department of Energy (DOE) on December 15, 1993, Advanced Reactors Transition (ART), previously known as Advanced Reactors, will provide the planning and perform the necessary activities for placing the Fast Flux Test Facility (FFTF) in a radiologically and industrially safe shutdown condition. The DOE goal is to accomplish the shutdown in approximately five years. The Advanced Reactors Transition Multi-Year Program Plan, and the supporting documents; i.e., the FFTF Shutdown Program Plan and the FFTF Shutdown Project Resource Loaded Schedule (RLS), are defined for the life of the Program. During the transition period to achieve the Shutdown end-state, the facilities and systems will continue to be maintained in a safe and environmentally sound condition. Additionally, facilities that were associated with the Office of Nuclear Energy (NE) Programs, and are no longer required to support the Liquid Metal Reactor Program will be deactivated and transferred to an alternate sponsor or the Decontamination and Decommissioning (D and D) Program for final disposition, as appropriate

  5. The story of the European fast reactor cooperation

    International Nuclear Information System (INIS)

    This report is a condensed history of European cooperation in the large breeder power plants with powers in excess of 1000 MWe. The beginning, in 1973, was marked by the so-called Utilities' Convention signed by EdF, RWE, and ENEL on the construction of Superphenix and SNR 2. In 1977, cooperation began among the reactor vendors and R and D organizations in France, Germany and Italy as well as Belgium and the Netherlands. After the British had joined in 1984, planning for the European Fast Reactor, EFR, was started in 1988. The conceptual design phase of the 1500 MWe breeder power plant covered a period of five years and was concluded with an economic assessment and a technical safety analysis of EFR in 1983. A number of ongoing studies are being conducted within a specific EFR program. (orig.)

  6. The Improvement of Plant Efficiency by Testing and Revising of the Reactor Thermal Power Calculation Program

    International Nuclear Information System (INIS)

    Since the uncertainty of flow measurement mostly affects the result of reactor thermal power calculation, reactor power in most of Nuclear Power Plants(NPPs) is controlled by excore Nuclear Instrumentation System(NIS) based on SPPC which has less uncertainty of flow measurement by using venture-meter. Real time monitoring system for reactor thermal power of Kori unit 3 and 4 has been established since 1992, and plant efficiency was improved by detecting errors and revising the program in 2012 following the engineering judgement that reactor thermal power varies according to steam generator blowdown flow change, unit conversion constant, and thermal expansion coefficient, etc. The reactor thermal power calculation program for Kori unit 3 and 4 was developed in 1992 and operated for 20 years without any correction or revision. Based on the engineering judgement that reactor thermal power varies according to change of steam generator blowdown flow, we conducted a research and found a couple of errors in steam generator blowdown specific volume, unit conversion constants for differential pressure of main feed water inlet flow, and thermal expansion coefficient of venture-meter which measures main feed water flow for steam generator. By correcting the errors in reactor thermal power program, generator power increased by 3.2 MWe for two units, Kori 3 and 4. Considering recent capacity factor of the plant, additional net electricity of 26,434 MWh was produced annually

  7. NEPTUNIX, a general program of simulation applied to nuclear reactors

    International Nuclear Information System (INIS)

    Most simulation languages admit an incremental description and involve explicit integration algorithms. NEPTUNIX is a simulation language directly admitting algebraic differential equations under an implicit form, and it involves a very efficient implicit integration method with variable step and order. NEPTUNIX is a tool used for building large systems models in the field of nuclear reactors

  8. Plutonium Consumption Program, CANDU Reactor Project final report

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-31

    DOE is investigating methods for long term dispositioning of weapons grade plutonium. One such method would be to utilize the plutonium in Mixed OXide (MOX) fuel assemblies in existing CANDU reactors. CANDU (Canadian Deuterium Uranium) reactors are designed, licensed, built, and supported by Atomic Energy of Canada Limited (AECL), and currently use natural uranium oxide as fuel. The MOX spent fuel assemblies removed from the reactor would be similar to the spent fuel currently produced using natural uranium fuel, thus rendering the plutonium as unattractive as that in the stockpiles of commercial spent fuel. This report presents the results of a study sponsored by the DOE for dispositioning the plutonium using CANDU technology. Ontario Hydro`s Bruce A was used as reference. The fuel design study defined the optimum parameters to disposition 50 tons of Pu in 25 years (or 100 tons). Two alternate fuel designs were studied. Safeguards, security, environment, safety, health, economics, etc. were considered. Options for complete destruction of the Pu were also studied briefly; CANDU has a superior ability for this. Alternative deployment options were explored and the potential impact on Pu dispositioning in the former Soviet Union was studied. An integrated system can be ready to begin Pu consumption in 4 years, with no changes required to the reactors other than for safe, secure storage of new fuel.

  9. Plutonium Consumption Program, CANDU Reactor Project final report

    International Nuclear Information System (INIS)

    DOE is investigating methods for long term dispositioning of weapons grade plutonium. One such method would be to utilize the plutonium in Mixed OXide (MOX) fuel assemblies in existing CANDU reactors. CANDU (Canadian Deuterium Uranium) reactors are designed, licensed, built, and supported by Atomic Energy of Canada Limited (AECL), and currently use natural uranium oxide as fuel. The MOX spent fuel assemblies removed from the reactor would be similar to the spent fuel currently produced using natural uranium fuel, thus rendering the plutonium as unattractive as that in the stockpiles of commercial spent fuel. This report presents the results of a study sponsored by the DOE for dispositioning the plutonium using CANDU technology. Ontario Hydro's Bruce A was used as reference. The fuel design study defined the optimum parameters to disposition 50 tons of Pu in 25 years (or 100 tons). Two alternate fuel designs were studied. Safeguards, security, environment, safety, health, economics, etc. were considered. Options for complete destruction of the Pu were also studied briefly; CANDU has a superior ability for this. Alternative deployment options were explored and the potential impact on Pu dispositioning in the former Soviet Union was studied. An integrated system can be ready to begin Pu consumption in 4 years, with no changes required to the reactors other than for safe, secure storage of new fuel

  10. Fiscal year 1998 multi-year work plan. Advanced reactors transition program

    International Nuclear Information System (INIS)

    The mission of the Advanced Reactors Transition program is two-fold. First, the program is to maintain the Fast Flux Test Facility (FFTF) and the Fuels and Materials Examination Facility (FMEF) in Standby to support a possible future role in the tritium production strategy. Secondly, the program is to continue deactivation activities which do not conflict with the Standby directive. On-going deactivation activities include the processing of non-usable, irradiated, FFTF components for storage or disposal; deactivation of Nuclear Energy legacy test facilities; and deactivation of the Plutonium Recycle Test Reactor (PRTR) facility, 309 Building

  11. A computer program to determine the specific power of prismatic-core reactors

    International Nuclear Information System (INIS)

    A computer program has been developed to determine the maximum specific power for prismatic-core reactors as a function of maximum allowable fuel temperature, core pressure drop, and coolant velocity. The prismatic-core reactors consist of hexagonally shaped fuel elements grouped together to form a cylindrically shaped core. A gas coolant flows axially through circular channels within the elements, and the fuel is dispersed within the solid element material either as a composite or in the form of coated pellets. Different coolant, fuel, coating, and element materials can be selected to represent different prismatic-core concepts. The computer program allows the user to divide the core into any arbitrary number of axial levels to account for different axial power shapes. An option in the program allows the automatic determination of the core height that results in the maximum specific power. The results of parametric specific power calculations using this program are presented for various reactor concepts

  12. Reactor Engineering Division annual report

    International Nuclear Information System (INIS)

    Research and development activities in the Division of Reactor Engineering in fiscal 1981 are described. The work of the Division is closely related to development of multipurpose Very High Temperature Gas Cooled Reactor and fusion reactor, and development of Liquid Metal Fast Breeder Reactor carried out by Power Reactor and Nuclear Fuel Development Corporation. Contents of the report are achievements in fields such as nuclear data and group constants, theoretical method and code development, integral experiment and analysis, shielding, reactor and nuclear instrumentation, reactor control and diagnosis, and fusion reactor technology, and activities of the Committee on Reactor Physics. (author)

  13. Helium-cooled molten-salt fusion breeder

    International Nuclear Information System (INIS)

    We present a new conceptual design for a fusion reactor blanket that is intended to produce fissile material for fission power plants. Fast fission is suppressed by using beryllium instead of uranium to multiply neutrons. Thermal fission is suppressed by minimizing the fissile inventory. The molten-salt breeding medium (LiF + BeF2 + ThF4) is circulated through the blanket and to the on-line processing system where 233U and tritium are continuously removed. Helium cools the blanket and the austenitic steel tubes that contain the molten salt. Austenitic steel was chosen because of its ease of fabrication, adequate radiation-damage lifetime, and low corrosion by molten salt. We estimate that a breeder having 3000 MW of fusion power will produce 6500 kg of 233U per year. This amount is enough to provide makeup for 20 GWe of light-water reactors per year or twice that many high-temperature gas-cooled reactors or Canadian heavy-water reactors. Safety is enhanced because the afterheat is low and blanket materials do not react with air or water. The fusion breeder based on a pre-MARS tandem mirror is estimated to cost $4.9B or 2.35 times a light-water reactor of the same power. The estimated cost of the 233U produced is $40/g for fusion plants costing 2.35 times that of a light-water reactor if utility owned or $16/g if government owned

  14. Nuclear science. U.S. electricity needs and DOE's civilian reactor development program

    International Nuclear Information System (INIS)

    Electricity projections developed by the North American Electric Reliability Council (NERC) appear to be the best available estimates of future U.S. electricity needs. NERC, which represents all segments of the utility industry, forecasts that before 1998 certain regions of the country, particularly in the more heavily populated eastern half of the United States, may experience shortfalls during summer peak demand periods. These forecasts considered the utility companies' plans, as of 1989, to meet electricity needs during the period; these plans include such measures as constructing additional generators and conducting demand management programs. Working closely with the nuclear industry, DOE is supporting the development of several reactor technologies to ensure that nuclear power remains a viable electricity supply option. In fiscal year 1990, DOE's Civilian Reactor Development Program was funded at $253 million. DOE is using these funds to support industry-led efforts to develop light water reactors (LWR), advanced liquid-metal reactors (LMR), and modular high-temperature gas-cooled reactors (MHTGR) that are safe, environmentally acceptable, and economically competitive. The utility company officials we spoke with, all of whom were in the Southeast, generally supported DOE's efforts in developing these technologies. However, most of the officials do not plan to purchase nuclear reactors until after 2000 because of the high costs of constructing nuclear reactors and current public opposition to nuclear power

  15. Information and education programs at the Washington State University research reactor

    International Nuclear Information System (INIS)

    Tours of the Nuclear Radiation Center are a common activity throughout the year, conducted for University classes, organized tour groups from other universities, private tour groups, and individuals. Increased awareness of nuclear activity and the existence of a research reactor on-campus has led to a heightened interest in reactor operations. The information and education programs at Washington State University have been directed at the individual needs and requirements of diverse interests. (author)

  16. U.S. Department of Energy Program of International Technical Cooperation for Research Reactor Utilization

    Energy Technology Data Exchange (ETDEWEB)

    Chong, D.; Manning, M.; Ellis, R.; Apt, K.; Flaim, S.; Sylvester, K.

    2004-10-03

    The U.S. Department of Energy, National Nuclear Security Administration (DOE/NNSA) has initiated collaborations with the national nuclear authorities of Egypt, Peru, and Romania for the purpose of advancing the commercial potential and utilization of their respective research reactors. Under its Office of International Safeguards ''Sister Laboratory'' program, DOE/NNSA has undertaken numerous technical collaborations over the past decade intended to promote peaceful applications of nuclear technology. Among these has been technical assistance in research reactor applications, such as neutron activation analysis, nuclear analysis, reactor physics, and medical radioisotope production. The current collaborations are intended to provide the subject countries with a methodology for greater commercialization of research reactor products and services. Our primary goal is the transfer of knowledge, both in administrative and technical issues, needed for the establishment of an effective business plan and utilization strategy for the continued operation of the countries' research reactors. Technical consultation, cooperation, and the information transfer provided are related to: identification, evaluation, and assessment of current research reactor capabilities for products and services; identification of opportunities for technical upgrades for new or expanded products and services; advice and consultation on research reactor upgrades and technical modifications; characterization of markets for reactor products and services; identification of competition and estimation of potential for market penetration; integration of technical constraints; estimation of cash flow streams; and case studies.

  17. U.S. Department of Energy Program of International Technical Cooperation for Research Reactor Utilization

    International Nuclear Information System (INIS)

    The U.S. Department of Energy, National Nuclear Security Administration (DOE/NNSA) has initiated collaborations with the national nuclear authorities of Egypt, Peru, and Romania for the purpose of advancing the commercial potential and utilization of their respective research reactors. Under its Office of International Safeguards ''Sister Laboratory'' program, DOE/NNSA has undertaken numerous technical collaborations over the past decade intended to promote peaceful applications of nuclear technology. Among these has been technical assistance in research reactor applications, such as neutron activation analysis, nuclear analysis, reactor physics, and medical radioisotope production. The current collaborations are intended to provide the subject countries with a methodology for greater commercialization of research reactor products and services. Our primary goal is the transfer of knowledge, both in administrative and technical issues, needed for the establishment of an effective business plan and utilization strategy for the continued operation of the countries' research reactors. Technical consultation, cooperation, and the information transfer provided are related to: identification, evaluation, and assessment of current research reactor capabilities for products and services; identification of opportunities for technical upgrades for new or expanded products and services; advice and consultation on research reactor upgrades and technical modifications; characterization of markets for reactor products and services; identification of competition and estimation of potential for market penetration; integration of technical constraints; estimation of cash flow streams; and case studies

  18. SR's reactor tank inspection program: UT development, application, and results

    International Nuclear Information System (INIS)

    Savannah River Site (SRS) has the nation's only plutonium and tritium production reactors. All three reactors have been idle for more than a year so that a variety of modifications can be made. Modifications are being carried out to enhance safety and technical systems. A 1987 decision was made to develop an inspection capability which would allow volumetric inspection of the SRS reactor tanks for the purpose of life extension. The scope of this inspection was defined to address the heat affected zones (HAZ's) of the tanks' weldments for the presence of service induced flaws, i.e., intergranular stress corrosion cracking (IGSCC). In order to be consistent with the existing practices and technology of the nuclear industry a state-of-the-art ultrasonic (UT) examination was chosen as the primary examination medium. Both ultrasonic and eddy current testing were selected as complementary methods for this application, since both can be configured to acquire test data remotely, and the test data can be digitized and stored for post-test analysis. Since intergranular stress corrosion cracking was believed to be the service-induced flaw most likely to occur adjacent to SRS's type 304 stainless steel reactor tank welds, the Savannah River Site's nondestructive testing specialists were faced with a unique challenge. Up to this point the major concentration of effort in the commercial nuclear world has been to apply ultrasonic testing techniques which were developed to detect and size IGSCC on the inside surface of piping with the search unit scanning on the outside surface of the pipe. Proven methods for detection and depth sizing IGSCC which initiated on the near surface (the surface in which the ultrasonic wave enters the metal) had not been established

  19. Production behavior of irradiation defects in solid breeder materials

    Energy Technology Data Exchange (ETDEWEB)

    Moriyama, Hirotake; Moritani, Kimikazu [Kyoto Univ. (Japan)

    1998-03-01

    The irradiation effects in solid breeder materials are important for the performance assessment of fusion reactor blanket systems. For a clearer understanding of such effects, we have studied the production behavior of irradiation defects in some lithium ceramics by an in-situ luminescence measurement technique under ion beam irradiation. The luminescence spectra were measured at different temperatures, and the temperature-transient behaviors of luminescence intensity were also measured. The production mechanisms of irradiation defects were discussed on the basis of the observations. (author)

  20. Status of University of Cincinnati reactor-site nuclear engineering graduate programs

    International Nuclear Information System (INIS)

    The University of Cincinnati (UC) nuclear engineering program faculty has now had 12 yr of experience in delivering reactor-site educational programs to nuclear power plant technical personnel. Currently, with the sponsorship of the Toledo-Edison Company (TED), we are conducting a multiyear on-site graduate program with more than 30 participants at the Davis-Besse nuclear power plant. The program enables TED employees with the proper academic background to earn a master of science (MS) degree in nuclear engineering (mechanical engineering option). This paper presents a brief history of tile evolution of UC reactor-site educational programs together with a description of the progress of the current program