On the upstream boundary of electron foreshocks in the solar wind

Science.gov (United States)

Zimbardo, G.; Veltri, P.

1995-01-01

The upstream boundary of electron foreshocks is defined as the path of the fastest electrons reflected by collisionless shocks and moving along the magnetic field in the solar wind. Considerable levels of magnetic fluctuations are found in these regions of the solar wind, and their effect is to create both a broadening and a fine structure of the electron foreshock boundary. The magnetic structure is studied by means of a 3-D numerical simulation of a turbulent magnetic field. Enhanced, anomalous diffusion is found, (Delta x(exp 2)) varies as s(sup alpha), where alpha is greater than 1 for typical values of the parameters (here, Delta x(exp 2) is the mean square width of the tangent magnetic surface and s is the field line length). This corresponds to a Levy flight regime for the magnetic field line random walk, and allows very efficient electron propagation perpendicular to the magnetic field. Implications on the observations of planetary foreshocks and of the termination shock foreshock are considered.

Additive recovery of lateral boundaries of grains under electronic exposure

International Nuclear Information System (INIS)

Postnikov, D.V.; Plotnikov, S.V.

2002-01-01

The experimental investigation of additive re-distribution under electronic beam revealed a recovery of the additive at grain boundaries. Additive accumulation mainly takes place at the boundaries that are perpendicular to material surface, whereas there is no an observed recovery of additive at the boundaries that are parallel to the surface. The additive recovery is caused by spot fault gradients near the grain boundary. The grain boundary is an intensive run-off region of vacancies. Therefore, the average vacancy distribution profile near the grain boundary changes its pattern. The above case indicates that there are two additive fluxes. One of them is vectored perpendicular to the surface, and the other one is parallel to it, i. e. it is vectored to the grain boundary. A study of the perpendicular and parallel boundaries shows that there is no additive settling at the boundaries that are parallel to the surface, since the general flux is vectored to the parallel boundaries. There is no such kind of phenomenon at the grain boundaries that are perpendicular to the surface. Besides, the perpendicular boundaries are more effective run-off regions for vacancies, since there is a slower build-up of the region with vacancies due to displacement of the vacancies to the surface. To compute concentration of vacancies we will consider a grain of the surface as a model. The computations indicate the presence of vacancy gradients vectored to the surface and grain boundaries, which are perpendicular to the surface. Comparison of the experimental and theoretical outcomes shows a good agreement between the theoretical model and actual processes occurring under the exposure. This theory disclose wide potentials for application of diffusion processes in alloys

Making the Water–Soil–Waste Nexus Work: Framing the Boundaries of Resource Flows

Czech Academy of Sciences Publication Activity Database

Avellán, T.; Roidt, M.; Emmer, Adam; von Koerber, J.; Schneider, P.; Raber, V.

2017-01-01

Roč. 9, č. 10 (2017), č. článku 1881. ISSN 2071-1050 R&D Projects: GA MŠk(CZ) LO1415 Institutional support: RVO:86652079 Keywords : integrated water resources management * integrated natural resources management * water–energy–food nexus * boundary Subject RIV: EH - Ecology, Behaviour OBOR OECD: Environmental sciences (social aspects to be 5.7) Impact factor: 1.789, year: 2016

Balancing platform control and external contribution in third-party development: the boundary resources model

DEFF Research Database (Denmark)

Ghazawneh, Ahmad; Henfridsson, Ola

2013-01-01

Prior research documents the significance of using platform boundary resources (e.g. application programming interfaces) for cultivating platform ecosystems through third-party development. However, there are few, if any, theoretical accounts of this relationship. To this end, this paper proposes......-party development: self-resourcing, regulation-based securing, diversity resourcing and sovereignty securing. Our research extends and complements existing platform literature and contributes new knowledge about an alternative form of system development...

Gender Analysis Of Electronic Information Resource Use: The Case ...

African Journals Online (AJOL)

Based on the findings the study concluded that access and use of electronic information resources creates a “social digital divide” along gender lines. The study ... Finally, the library needs to change its marketing strategies on the availability of electronic information resources to increase awareness of these resources.

Users satisfaction with electronic information resources and services ...

African Journals Online (AJOL)

This study investigated users satisfaction on the use of electronic information resources and services in MTN Net libraries in ABU & UNIBEN. Two objectives and one null hypotheses were formulated and tested with respect to the users' satisfaction on electronic information resources and services in MTN Net libraries in ...

Atomic structures and electronic properties of phosphorene grain boundaries

International Nuclear Information System (INIS)

Guo, Yu; Zhou, Si; Bai, Yizhen; Zhao, Jijun; Zhang, Junfeng

2016-01-01

Grain boundary (GB) is one main type of defects in two-dimensional (2D) crystals, and has significant impact on the physical properties of 2D materials. Phosphorene, a recently synthesized 2D semiconductor, possesses a puckered honeycomb lattice and outstanding electronic properties. It is very interesting to know the possible GBs present in this novel material, and how their properties differ from those in the other 2D materials. Based on first-principles calculations, we explore the atomic structure, thermodynamic stability, and electronic properties of phosphorene GBs. A total of 19 GBs are predicted and found to be energetically stable with formation energies much lower than those in graphene. These GBs do not severely affect the electronic properties of phosphorene: the band gap of perfect phosphorene is preserved, and the electron mobilities are only moderately reduced in these defective systems. Our theoretical results provide vital guidance for experimental tailoring the electronic properties of phosphorene as well as the device applications using phosphorene materials. (paper)

Organizational matters of competition in electronic educational resources

Directory of Open Access Journals (Sweden)

Ирина Карловна Войтович

2015-12-01

Full Text Available The article examines the experience of the Udmurt State University in conducting competitions of educational publications and electronic resources. The purpose of such competitions is to provide methodological support to educational process. The main focus is on competition of electronic educational resources. The technology of such contests is discussed through detailed analysis of the main stages of the contest. It is noted that the main task of the preparatory stage of the competition is related to the development of regulations on competition and the definition of criteria for selection of the submitted works. The paper also proposes a system of evaluation criteria of electronic educational resources developed by members of the contest organizing committee and jury members. The article emphasizes the importance of not only the preparatory stages of the competition, but also measures for its completion, aimed at training teachers create quality e-learning resources.

CHALLENGES OF ELECTRONIC INFORMATION RESOURCES IN ...

African Journals Online (AJOL)

This paper discusses the role of policy for proper and efficient library services in the electronic era. It points out some of the possible dangers of embarking in electronic resources without a proper focus at hand. Thus, it calls for today's librarians and policy makers to brainstorm and come up with working policies suitable to ...

Use of Electronic Resources in a Private University in Nigeria ...

African Journals Online (AJOL)

The study examined awareness and constraints in the use of electronic resources by lecturers and students of Ajayi Crowther University, Oyo, Nigeria. It aimed at justifying the resources expended in the provision of electronic resources in terms of awareness, patronage and factors that may be affecting awareness and use ...

Electronic Resources Management System: Recommendation Report 2017

KAUST Repository

Ramli, Rindra M.

2017-05-01

This recommendation report provides an overview of the selection process for the new Electronic Resources Management System. The library has decided to move away from Innovative Interfaces Millennium ERM module. The library reviewed 3 system as potential replacements namely: Proquest 360 Resource Manager, Ex Libris Alma and Open Source CORAL ERMS. After comparing and trialling the systems, it was decided to go for Proquest 360 Resource Manager.

Scanning electron microscope cathodoluminescence imaging of subgrain boundaries, twins and planar deformation features in quartz

Science.gov (United States)

Hamers, M. F.; Pennock, G. M.; Drury, M. R.

2017-04-01

The study of deformation features has been of great importance to determine deformation mechanisms in quartz. Relevant microstructures in both growth and deformation processes include dislocations, subgrains, subgrain boundaries, Brazil and Dauphiné twins and planar deformation features (PDFs). Dislocations and twin boundaries are most commonly imaged using a transmission electron microscope (TEM), because these cannot directly be observed using light microscopy, in contrast to PDFs. Here, we show that red-filtered cathodoluminescence imaging in a scanning electron microscope (SEM) is a useful method to visualise subgrain boundaries, Brazil and Dauphiné twin boundaries. Because standard petrographic thin sections can be studied in the SEM, the observed structures can be directly and easily correlated to light microscopy studies. In contrast to TEM preparation methods, SEM techniques are non-destructive to the area of interest on a petrographic thin section.

use of electronic resources by graduate students of the department

African Journals Online (AJOL)

respondent's access electronic resources from the internet via Cybercafé .There is a high ... KEY WORDS: Use, Electronic Resources, Graduate Students, Cybercafé. INTRODUCTION ... Faculty of Education, University of Uyo, Uyo. Olu Olat ...

Variations of electron fluxes in the outer radiation belt near the boundary of a trapping region during substorms

International Nuclear Information System (INIS)

Ginzburg, E.A.; Malyshev, A.B.

1979-01-01

Variations of electron fluxes with the energy Esub(e) > 0.7 MeV have been investigated near the high-latitude boundary of electron trapping region in the night and day sections of the magnetosphere. It is found that during substorms the natural changes of the structure of electron fluxes take place. On the night side of the magnetosphere after the flux boundary drift to the equator at the preliminary phase, its sharp drift to the pole at the explosion phase takes place with further slow ( during 1-2 hours) shift to the initial position. The boundary position reconstruction period coincide by duration with the life time of negative bays at magnetograms of the night section stations. On the day side the boundary of electron fluxes recorded drifts to the pole in 30-60 min after the beginning of the substorm exposion phase. The results obtained are interpreted within the framework of the theory of adiabatic drift of trapped electrons and their pitch-angular diffusion under the effect of very low frequency waves

Simulation of grain boundary effects on electronic transport in metals, and detailed causes of scattering

Energy Technology Data Exchange (ETDEWEB)

Feldman, Baruch [Process Technology Modeling, Design and Technology Solutions, Technology and Manufacturing Group, Intel Corporation, Santa Clara, CA 95052 (United States); Department of Physics, University of Washington, Seattle, WA 98195 (United States); Park, Seongjun; Haverty, Michael; Shankar, Sadasivan [Process Technology Modeling, Design and Technology Solutions, Technology and Manufacturing Group, Intel Corporation, Santa Clara, CA 95052 (United States); Dunham, Scott T. [Department of Physics, University of Washington, Seattle, WA 98195 (United States); Department of Electrical Engineering, University of Washington, Seattle, WA 98195 (United States)

2010-07-15

We present first-principles simulations of single grain boundary reflectivity of electrons in noble metals, Cu and Ag. We examine twin and non-twin grain boundaries using non-equilibrium Green's function and first principles methods. We also investigate the determinants of reflectivity in grain boundaries by modeling atomic vacancies, disorder, and orientation and find that both the change in grain orientation and disorder in the boundary itself contribute significantly to reflectivity. We find that grain boundary reflectivity may vary widely depending on the grain boundary structure, consistent with published experimental results. Finally, we examine the reflectivity from multiple grain boundaries and find that grain boundary reflectivity may depend on neighboring grain boundaries. This study raises some potential limitations in the independent grain boundary assumptions of the Mayadas-Shatzkes (MS) model. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Electronic resource management practical perspectives in a new technical services model

CERN Document Server

Elguindi, Anne

2012-01-01

A significant shift is taking place in libraries, with the purchase of e-resources accounting for the bulk of materials spending. Electronic Resource Management makes the case that technical services workflows need to make a corresponding shift toward e-centric models and highlights the increasing variety of e-formats that are forcing new developments in the field.Six chapters cover key topics, including: technical services models, both past and emerging; staffing and workflow in electronic resource management; implementation and transformation of electronic resource management systems; the ro

The boundary-corrected second Born (B2B) approximation: proton-hydrogen electron capture

International Nuclear Information System (INIS)

Dewangan, D.P.; Bransden, B.H.

1988-01-01

The probability amplitude for proton-hydrogen ground-state electron capture at 125 keV in the boundary-corrected second Born approximation has been evaluated numerically by retaining all significant bound and continuum hydrogenic intermediate states for which the orbital angular momentum l ≤ 3. The differential cross section is found to be in good agreement with the experimental data for scattering angles less than about 1 mrad in the centre of mass system. The value of the boundary-corrected second Born total cross section is similar to that obtained in the boundary-corrected first Born approximation. (author)

Utilization of electronic information resources by academic staff at ...

African Journals Online (AJOL)

The study investigated the utilization of Electronic Information resources by the academic staff of Makerere University in Uganda. It examined the academic staff awareness of the resources available, the types of resources provided by the Makerere University Library, the factors affecting resource utilization. The study was ...

Interaction of magnetized electrons with a boundary sheath: investigation of a specular reflection model

Science.gov (United States)

Krüger, Dennis; Brinkmann, Ralf Peter

2017-11-01

This publication reports analytical and numerical results concerning the interaction of gyrating electrons with a plasma boundary sheath, with focus on partially magnetized technological plasmas. It is assumed that the electron Debye length {λ }{{D}} is much smaller than the electron gyroradius {r}{{L}}, and {r}{{L}} in turn much smaller than the mean free path λ and the gradient length L of the fields. Focusing on the scale of the gyroradius, the sheath is assumed as infinitesimally thin ({λ }{{D}}\\to 0), collisions are neglected (λ \\to ∞ ), the magnetic field is taken as homogeneous, and electric fields (=potential gradients) in the bulk are neglected (L\\to ∞ ). The interaction of an electron with the electric field of the plasma boundary sheath is represented by a specular reflection {v}\\to {v}-2{v}\\cdot {{e}}z {{e}}z of the velocity {v} at the plane z = 0 of a naturally oriented Cartesian coordinate system (x,y,z). The electron trajectory is then given as sequences of helical sections, with the kinetic energy ɛ and the canonical momenta p x and p y conserved, but not the position of the axis (base point {{R}}0), the slope (pitch angle χ), and the phase (gyrophase φ). A ‘virtual interaction’ which directly maps the incoming electrons to the outgoing ones is introduced and studied in dependence of the angle γ between the field and the sheath normal {{e}}z. The corresponding scattering operator is constructed, mathematically characterized, and given as an infinite matrix. An equivalent boundary condition for a transformed kinetic model is derived.

Electronic Resources Management Project Presentation 2012

KAUST Repository

Ramli, Rindra M.

2012-01-01

This presentation describes the electronic resources management project undertaken by the KAUST library. The objectives of this project is to migrate information from MS Sharepoint to Millennium ERM module. One of the advantages of this migration

Structural evolution of a deformed Σ=9 (122) grain boundary in silicon. A high resolution electron microscopy study

International Nuclear Information System (INIS)

Putaux, Jean-Luc

1991-01-01

This research thesis addresses the study by high resolution electron microscopy of the evolution of a silicon bi-crystal under deformation at different temperatures. The author notably studied the structural evolution of the boundary as well as that of grains at the vicinity of the boundary. Two observation scales have been used: the evolution of sub-structures of dislocations induced by deformation in grains and in boundary, and the structure of all defects at an atomic scale. After a presentation of experimental tools (the necessary perfect quality of the electronic optics is outlined), the author recalls some descriptive aspects of grain boundaries (geometric network concepts to describe coinciding networks, concepts of delimiting boundaries and of structural unit to describe grain boundary atomic structure), recalls the characteristics of the studied bi-crystal, and the conditions under which it is deformed. He presents the structures of all perfectly coinciding boundaries, describes defects obtained by deformation at the vicinity of the boundary, describes the entry of dissociated dislocations into the boundaries, and discusses the characterization of boundary dislocations (the notion of Burgers vector is put into question again), and the atomic mechanism of displacement of dislocations in boundaries [fr

The PhotoElectron Boundary as observed by MAVEN instruments

Science.gov (United States)

Garnier, P.; Steckiewicz, M.; Mazelle, C. X.; Xu, S.; Mitchell, D. L.; Holmberg, M.; Halekas, J. S.; Andersson, L.; Brain, D.; Connerney, J. E. P.; Espley, J. R.; Lillis, R. J.; Luhmann, J. G.; Savaud, J. A.; Jakosky, B. M.

2017-12-01

Photoelectron peaks in the 20-30 eV energy range are commonly observed in planetary atmospheres (Earth, Mars, Titan...), produced by the intense photoionization from solar 30.4 nm photons. At Mars, these photoelectrons result from the ionization of CO2 and O atmospheric neutrals, and are known to escape the planet down its tail, making them tracers for the atmospheric escape (Frahm et al., 2006). Furthermore, their presence or absence allows us to define the so-called PhotoElectron Boundary (PEB), that separates the sunlit photoelectron-dominated ionosphere from the solar wind controlled environment, as initially observed by the Mars Global Surveyor (MGS) MAG/ER instrument (Mitchell et al. (2000, 2001). We provide here a detailed statistical analysis of the location and properties of the PEB based on the Mars Atmosphere and Volatile Evolution (MAVEN) mission electron and magnetic field data. Our dataset includes 1696 dayside PEB crossings obtained from September 2014 until May 2016 (the observations of escaping photoelectrons in the wake being not included). The PEB appears as mostly sensitive to the solar wind dynamic and crustal magnetic fields pressures, for which a quantitative dependance is derived and compared with two other important boundaries : the bow shock and magnetic pileup boundary. The PEB altitude is highly variable, leading to a variable wake cross section for escape (up to +- 50%), which is important for deriving global escape rates from in situ photoelectron escape rates. The PEB is not always sharp, and is, despite a strong variability, characterized on average by : a magnetic field topology typical for the edge of the Magnetic Pile Up Region above it, more field aligned fluxes above than below, and a clear change of the altitude dependence of both electron fluxes and total density (that appears different from the ionopause). The PEB thus appears as a transition region between two plasma and field configurations which is determined by the

Practical guide to electronic resources in the humanities

CERN Document Server

Dubnjakovic, Ana

2010-01-01

From full-text article databases to digitized collections of primary source materials, newly emerging electronic resources have radically impacted how research in the humanities is conducted and discovered. This book, covering high-quality, up-to-date electronic resources for the humanities, is an easy-to-use annotated guide for the librarian, student, and scholar alike. It covers online databases, indexes, archives, and many other critical tools in key humanities disciplines including philosophy, religion, languages and literature, and performing and visual arts. Succinct overviews of key eme

Utilisation of Electronic Information Resources By Lecturers in ...

African Journals Online (AJOL)

This study assesses the use of information resources, specifically, electronic databases by lecturers/teachers in Universities and Colleges of Education in South Western Nigeria. Information resources are central to teachers' education. It provides lecturers/teachers access to information that enhances research and ...

Rearranging social space: Boundary-making and boundary-work in a joint forest management project, Andhra Pradesh, India

Directory of Open Access Journals (Sweden)

Saito-Jensen Moeko

2010-01-01

Full Text Available Since the 1990s, there has been an increasing trend in developing countries to shift from state driven approaches to Community-based Natural Resource Management (CBNRM. In order to ensure sustainability of resources, the need for creating and maintaining clear resource use boundaries has been emphasised, both theoretically and in practice. However, there has been less attention to the varied social consequences for involved villages (whose inhabitants can access resources within the new boundaries and for excluded villages (whose inhabitants are prevented from accessing resources due to these boundaries. Drawing on a case study of three villages affected by the Joint Forest Management project in Andhra Pradesh, India, this article shows how resource use boundaries interact with social categories such as caste, gender and livelihood occupation in ways that facilitate asymmetric distribution of costs and benefits among local people. The article calls for more consultative processes in constituting new resources use boundaries and for flexible interventions to reconcile conflicts arising from boundary-making.

Moving the boundary between wavelength resources in optical packet and circuit integrated ring network.

Science.gov (United States)

Furukawa, Hideaki; Miyazawa, Takaya; Wada, Naoya; Harai, Hiroaki

2014-01-13

Optical packet and circuit integrated (OPCI) networks provide both optical packet switching (OPS) and optical circuit switching (OCS) links on the same physical infrastructure using a wavelength multiplexing technique in order to deal with best-effort services and quality-guaranteed services. To immediately respond to changes in user demand for OPS and OCS links, OPCI networks should dynamically adjust the amount of wavelength resources for each link. We propose a resource-adjustable hybrid optical packet/circuit switch and transponder. We also verify that distributed control of resource adjustments can be applied to the OPCI ring network testbed we developed. In cooperation with the resource adjustment mechanism and the hybrid switch and transponder, we demonstrate that automatically allocating a shared resource and moving the wavelength resource boundary between OPS and OCS links can be successfully executed, depending on the number of optical paths in use.

On the upstream boundary of electron foreshocks in the solar wind

International Nuclear Information System (INIS)

Zimbardo, G.; Veltri, P.

1996-01-01

The backstreaming of electrons from planetary and interplanetary shocks creates foreshocks of fast particles propagating along the magnetic field. The effect of low frequency magnetic fluctuations is to create both a broadening and a fine structure of the foreshock upstream boundary. This is studied by means of a newly developed 3-D numerical simulation of turbulent magnetic fields. Applications to the Earth and to the termination shock electron foreshocks are done, and some implications on the observations of the spreading and of the bursty structure of the foreshocks are discussed

Discipline, availability of electronic resources and the use of Finnish National Electronic Library - FinELib

Directory of Open Access Journals (Sweden)

Sanna Torma

2004-01-01

Full Text Available This study elaborated relations between digital library use by university faculty, users' discipline and the availability of key resources in the Finnish National Electronic Library (FinELib, Finnish national digital library, by using nationwide representative survey data. The results show that the perceived availability of key electronic resources by researchers in FinELib was a stronger predictor of the frequency and purpose of use of its services than users' discipline. Regardless of discipline a good perceived provision of central resources led to a more frequent use of FinELib. The satisfaction with the services did not vary with the discipline, but with the perceived availability of resources.

The Role of the Acquisitions Librarian in Electronic Resources Management

Science.gov (United States)

Pomerantz, Sarah B.

2010-01-01

With the ongoing shift to electronic formats for library resources, acquisitions librarians, like the rest of the profession, must adapt to the rapidly changing landscape of electronic resources by keeping up with trends and mastering new skills related to digital publishing, technology, and licensing. The author sought to know what roles…

Analysis of Pedagogic Potential of Electronic Educational Resources with Elements of Autodidactics

Directory of Open Access Journals (Sweden)

Igor A.

2018-03-01

Full Text Available Introduction: in recent years didactic properties of electronic educational resources undergo considerable changes, nevertheless, the question of studying of such complete phenomenon as “an electronic educational resource with autodidactics elements” remains open, despite sufficient scientific base of researches of the terms making this concept. Article purpose – determination of essence of electronic educational resources with autodidactics elements. Materials and Methods: the main method of research was the theoretical analysis of the pedagogical and psychological literature on the problem under study. We used the theoretical (analysis, synthesis, comparison and generalization methods, the method of interpretation, pedagogical modeling, and empirical methods (observation, testing, conversation, interview, analysis of students’ performance, pedagogical experiment, peer review. Results: we detected the advantages of electronic educational resources in comparison with traditional ones. The concept of autodidactics as applied to the subject of research is considered. Properties of electronic educational resources with a linear and nonlinear principle of construction are studied.The influence of the principle of construction on the development of the learners’ qualities is shown. We formulated an integral definition of electronic educational resources with elements of autodidactics, namely, the variability, adaptivity and cyclicity of training. A model of the teaching-learning process with electronic educational resources is developed. Discussion and Conclusions: further development of a problem will allow to define whether electronic educational resources with autodidactics elements pedagogical potential for realization of educational and self-educational activity of teachers have, to modify technological procedures taking into account age features of students, their specialties and features of the organization of process of training of

Preservation and conservation of electronic information resources of ...

African Journals Online (AJOL)

The major holdings of the broadcast libraries of the Nigerian Television Authority (NTA) are electronic information resources; therefore, providing safe places for general management of these resources have aroused interest in the industry in Nigeria for sometimes. The need to study the preservation and conservation of ...

Building an electronic resource collection a practical guide

CERN Document Server

Lee, Stuart D

2004-01-01

This practical book guides information professionals step-by-step through building and managing an electronic resource collection. It outlines the range of electronic products currently available in abstracting and indexing, bibliographic, and other services and then describes how to effectively select, evaluate and purchase them.

Analysis of Human Resources Management Strategy in China Electronic Commerce Enterprises

Science.gov (United States)

Shao, Fang

The paper discussed electronic-commerce's influence on enterprise human resources management, proposed and proved the human resources management strategy which electronic commerce enterprise should adopt from recruitment strategy to training strategy, keeping talent strategy and other ways.

Using XML Technologies to Organize Electronic Reference Resources

OpenAIRE

Huser, Vojtech; Del Fiol, Guilherme; Rocha, Roberto A.

2005-01-01

Provision of access to reference electronic resources to clinicians is becoming increasingly important. We have created a framework for librarians to manage access to these resources at an enterprise level, rather than at the individual hospital libraries. We describe initial project requirements, implementation details, and some preliminary results.

Electronic Resources and Mission Creep: Reorganizing the Library for the Twenty-First Century

Science.gov (United States)

Stachokas, George

2009-01-01

The position of electronic resources librarian was created to serve as a specialist in the negotiation of license agreements for electronic resources, but mission creep has added more functions to the routine work of electronic resources such as cataloging, gathering information for collection development, and technical support. As electronic…

Usage and Efficacy of Electronic Dictionaries for a Language without Word Boundaries

Science.gov (United States)

Toyoda, Etsuko

2016-01-01

There is cumulative evidence suggesting that hyper-glossing facilitates lower-level processing and enhances reading comprehension. There are plentiful studies on electronic dictionaries for English. However, research on e-dictionaries for languages with no boundaries between words is still scarce. The main aim for the current study is to…

Electronic Resources Management System: Recommendation Report 2017

KAUST Repository

Ramli, Rindra M.

2017-01-01

This recommendation report provides an overview of the selection process for the new Electronic Resources Management System. The library has decided to move away from Innovative Interfaces Millennium ERM module. The library reviewed 3 system

The Internet School of Medicine: use of electronic resources by medical trainees and the reliability of those resources.

Science.gov (United States)

Egle, Jonathan P; Smeenge, David M; Kassem, Kamal M; Mittal, Vijay K

2015-01-01

Electronic sources of medical information are plentiful, and numerous studies have demonstrated the use of the Internet by patients and the variable reliability of these sources. Studies have investigated neither the use of web-based resources by residents, nor the reliability of the information available on these websites. A web-based survey was distributed to surgical residents in Michigan and third- and fourth-year medical students at an American allopathic and osteopathic medical school and a Caribbean allopathic school regarding their preferred sources of medical information in various situations. A set of 254 queries simulating those faced by medical trainees on rounds, on a written examination, or during patient care was developed. The top 5 electronic resources cited by the trainees were evaluated for their ability to answer these questions accurately, using standard textbooks as the point of reference. The respondents reported a wide variety of overall preferred resources. Most of the 73 responding medical trainees favored textbooks or board review books for prolonged studying, but electronic resources are frequently used for quick studying, clinical decision-making questions, and medication queries. The most commonly used electronic resources were UpToDate, Google, Medscape, Wikipedia, and Epocrates. UpToDate and Epocrates had the highest percentage of correct answers (47%) and Wikipedia had the lowest (26%). Epocrates also had the highest percentage of wrong answers (30%), whereas Google had the lowest percentage (18%). All resources had a significant number of questions that they were unable to answer. Though hardcopy books have not been completely replaced by electronic resources, more than half of medical students and nearly half of residents prefer web-based sources of information. For quick questions and studying, both groups prefer Internet sources. However, the most commonly used electronic resources fail to answer clinical queries more than half

Plasma and energetic electron flux variations in the Mercury 1 C event: Evidence for a magnetospheric boundary layer

International Nuclear Information System (INIS)

Christon, S.P.

1989-01-01

Near the outbound magnetopause crossing during the first encounter of Mariner 10 with the planet Mercury on March 29, 1974, large intensity, ∼ 6 s quasi-periodic variations in the intensity-time profile of the charged particle experiment's electron counting rate appeared as a series of peaks and valleys. The peaks have previously been interpreted as quasi-periodic burst sequences of mildly relativistic electrons, caused in one case by episodic ∼ 6-s magnetotail substorm reconnection events and in another case by multiple encounters with a substorm energized electron population drifting around Mercury with an ∼ 6 s drift period. In this paper, the authors offer a new and fundamentally different interpretation of the Mariner 10 energetic electron, plasma electron, and magnetic field data near the outbound magnetopause at Mercury 1. They show that magnetosheath-like boundary layer plasma was observed up to ∼ 360 km planetward of the dawn magnetopause crossing as sensed by the magnetometer. They show that observations of substorm enhanced > 35 keV electron flux (that previously interpreted as > 175 keV electrons) associated with the hot tenuous plasma sheet population were interleaved with ∼ 6 s period observations of a cold dense boundary layer plasma associated with a much lower > 35 keV electron flux. They argue that the ∼ 6 s temporal signature is due to variation of the thickness and/or position of the boundary layer plasma population. This explanation of the ∼ 6-s variations, based upon the analysis of the coincident responses of the magnetic field experiment and two independent charged particle instruments (at their highest temporal resolutions), finds a direct analogue in observations of Earth's magnetospheric boundary layer, although the time scales are significantly shorter at Mercury

Localized electronic states at grain boundaries on the surface of graphene and graphite

DEFF Research Database (Denmark)

Luican-Mayer, Adina; Barrios-Vargas, Jose E.; Falkenberg, Jesper Toft

2016-01-01

ecent advances in large-scale synthesis of graphene and other 2D materials have underscored the importance of local defects such as dislocations and grain boundaries (GBs), and especially their tendency to alter the electronic properties of the material. Understanding how the polycrystalline morp...

Thermal boundary conditions for electrons in a weakly ionized gas near a catalytic wall

International Nuclear Information System (INIS)

Chekmarev, I.

1981-01-01

A technique of matched asymptotic expansions is used to examine the derivation of hydrodynamic transport equations for the external region of a weakly ionized multitemperature gas near an absorbing and conducting wall. An approximate moment solution is constructed for the Knudsen boundary layer. The conditions for the matching of the external and internal expansions lead to a new form of the hydrodynamic boundary conditions, from which the singular behavior of the energy equation for electrons near the wall has been eliminated

Magnetism in grain-boundary phase of a NdFeB sintered magnet studied by spin-polarized scanning electron microscopy

Energy Technology Data Exchange (ETDEWEB)

Kohashi, Teruo, E-mail: teruo.kohashi.fc@hitachi.com; Motai, Kumi [Central Research Laboratory, Hitachi, Ltd., Hatoyama, Saitama 350-0395 (Japan); Nishiuchi, Takeshi; Hirosawa, Satoshi [Magnetic Materials Research Laboratory, Hitachi Metals Ltd., Osaka 618-0013 (Japan)

2014-06-09

The magnetism in the grain-boundary phase of a NdFeB sintered magnet was measured by spin-polarized scanning electron microscopy (spin SEM). A sample magnet was fractured in the ultra-high-vacuum chamber to avoid oxidation, and its magnetizations in the exposed grain-boundary phase on the fracture surface were evaluated through the spin polarization of secondary electrons. Spin-SEM images were taken as the fracture surface was milled gradually by argon ions, and the magnetization in the grain-boundary phase was quantitatively obtained separately from that of the Nd{sub 2}Fe{sub 14}B phase. The obtained magnetization shows that the grain-boundary phase of this magnet has substantial magnetization, which was confirmed to be ferromagnetic.

ANALYTICAL REVIEW OF ELECTRONIC RESOURCES FOR THE STUDY OF LATIN

Directory of Open Access Journals (Sweden)

Olena Yu. Balalaieva

2014-04-01

Full Text Available The article investigates the current state of development of e-learning content in the Latin language. It is noted that the introduction of ICT in the educational space has expanded the possibility of studying Latin, opened access to digital libraries resources, made it possible to use scientific and educational potential and teaching Latin best practices of world's leading universities. A review of foreign and Ukrainian information resources and electronic editions for the study of Latin is given. Much attention was paid to the didactic potential of local and online multimedia courses of Latin, electronic textbooks, workbooks of interactive tests and exercises, various dictionaries and software translators, databases and digital libraries. Based on analysis of the world market of educational services and products the main trends in the development of information resources and electronic books are examined. It was found that multimedia courses with interactive exercises or workbooks with interactive tests, online dictionaries and translators are the most widely represented and demanded. The noticeable lagging of Ukrainian education and computer linguistics in quantitative and qualitative measures in this industry is established. The obvious drawback of existing Ukrainian resources and electronic editions for the study of Latin is their noninteractive nature. The prospects of e-learning content in Latin in Ukraine are outlined.

A comparison of the relative locations of the mid-latitude electron density trough and the scintillation boundary

International Nuclear Information System (INIS)

Tulunay, Y.K.; Demir, O.; Tauriainen, A.

1976-01-01

The mid-latitude electron density trough position and the scintillation boundary have been compared for magnetically quiet periods by using the data returned by Ariel 3 and Explorer 22 satellites. The scintillation boundary is found southward of the trough during daytime, but at night the positions are reversed. (author)

Elektronik Bilgi Kaynaklarının Seçimi / Selection of Electronic Information Resources

Directory of Open Access Journals (Sweden)

Pınar Al

2003-04-01

Full Text Available For many years, library users have used only from the printed media in order to get the information that they have needed. Today with the widespread use of the Web and the addition of electronic information resources to library collections, the use of information in the electronic environment as well as in printed media is started to be used. In time, such types of information resources as, electronic journals, electronic books, electronic encyclopedias, electronic dictionaries and electronic theses have been added to library collections. In this study, selection criteria that can be used for electronic information resources are discussed and suggestions are provided for libraries that try to select electronic information resources for their collections.

Structure and electronic properties of boron nitride sheet with grain boundaries

International Nuclear Information System (INIS)

Wang Zhiguo

2012-01-01

Using first-principles calculations, the structure, stability, and electronic properties of BN sheets with grain boundaries (GBs) are investigated. Two types of GBs, i.e., zigzag- and armchair-oriented GBs, are considered. Simulation results reveal that the zigzag-oriented GBs are more stable than the armchair-oriented ones. The GBs induce defect levels located within the band gap, which must be taken into account when building nanoelectronic devices.

Access to electronic resources by visually impaired people

Directory of Open Access Journals (Sweden)

Jenny Craven

2003-01-01

Full Text Available Research into access to electronic resources by visually impaired people undertaken by the Centre for Research in Library and Information Management has not only explored the accessibility of websites and levels of awareness in providing websites that adhere to design for all principles, but has sought to enhance understanding of information seeking behaviour of blind and visually impaired people when using digital resources.

Library training to promote electronic resource usage

DEFF Research Database (Denmark)

Frandsen, Tove Faber; Tibyampansha, Dativa; Ibrahim, Glory

2017-01-01

Purpose: Increasing the usage of electronic resources is an issue of concern for many libraries all over the world. Several studies stress the importance of information literacy and instruction in order to increase the usage. Design/methodology/approach: The present article presents the results...

Why and How to Measure the Use of Electronic Resources

Directory of Open Access Journals (Sweden)

Jean Bernon

2008-11-01

Full Text Available A complete overview of library activity implies a complete and reliable measurement of the use of both electronic resources and printed materials. This measurement is based on three sets of definitions: document types, use types and user types. There is a common model of definitions for printed materials, but a lot of questions and technical issues remain for electronic resources. In 2006 a French national working group studied these questions. It relied on the COUNTER standard, but found it insufficient and pointed out the need for local tools such as web markers and deep analysis of proxy logs. Within the French national consortium COUPERIN, a new working group is testing ERMS, SUSHI standards, Shibboleth authentication, along with COUNTER standards, to improve the counting of the electronic resources use. At this stage this counting is insufficient and its improvement will be a European challenge for the future.

Euler European Libraries and Electronic Resources in Mathematical Sciences

CERN Document Server

The Euler Project. Karlsruhe

The European Libraries and Electronic Resources (EULER) Project in Mathematical Sciences provides the EulerService site for searching out "mathematical resources such as books, pre-prints, web-pages, abstracts, proceedings, serials, technical reports preprints) and NetLab (for Internet resources), this outstanding engine is capable of simple, full, and refined searches. It also offers a browse option, which responds to entries in the author, keyword, and title fields. Further information about the Project is provided at the EULER homepage.

Effects of Electronic Information Resources Skills Training for Lecturers on Pedagogical Practices and Research Productivity

Science.gov (United States)

Bhukuvhani, Crispen; Chiparausha, Blessing; Zuvalinyenga, Dorcas

2012-01-01

Lecturers use various electronic resources at different frequencies. The university library's information literacy skills workshops and seminars are the main sources of knowledge of accessing electronic resources. The use of electronic resources can be said to have positively affected lecturers' pedagogical practices and their work in general. The…

The electron edge of the low latitude boundary layer during accelerated flow events

International Nuclear Information System (INIS)

Gosling, J.T.; Thomsen, M.F.; Bame, S.J.; Onsager, T.G.; Russel, C.T.

1990-01-01

Magnetosheath plasma entering the Earth's magnetosphere to populate the low latitude boundary layer, LLBL, is often accelerated to speeds considerably greater than are observed in the adjacent magnetosheath. Measurements made during such accelerated flow events reveal separate electron and ion edges to the LLBL, with the electron edge being found earthward of the ion edge. Plasma electron velocity distributions observed at the earthward edge of the LLBL are often highly structured, exhibiting large asymmetries parallel and antiparallel, as well as perpendicular, to the local magnetic field. These features can consistently be interpreted as time-of-flight effects on recently reconnected field lines, and thus are strong evidence in support of the reconnection interpretation of accelerated plasma flow events

Consequences of boundary-spanning demands and resources for work-to-family conflict and perceived stress.

Science.gov (United States)

Voydanoff, Patricia

2005-10-01

Using work-family border theory, this article examines relationships between boundary-spanning demands and resources and work-to-family conflict and perceived stress. The analysis uses data from 2,109 respondents from the 2002 National Study of the Changing Workforce. The demands that were positively related to work-to-family conflict and perceived stress were commuting time, bringing work home, job contacts at home, and work-family multitasking. Work-family multitasking partially explained the effects of bringing work home and job contacts at home on conflict and stress. For resources, time off for family responsibilities and a supportive work-family culture showed negative associations with conflict and stress. Work-to-family conflict partially mediated relationships between several demands and resources and perceived stress. Copyright (c) 2005 APA, all rights reserved.

Electronic Commerce Resource Centers. An Industry--University Partnership.

Science.gov (United States)

Gulledge, Thomas R.; Sommer, Rainer; Tarimcilar, M. Murat

1999-01-01

Electronic Commerce Resource Centers focus on transferring emerging technologies to small businesses through university/industry partnerships. Successful implementation hinges on a strategic operating plan, creation of measurable value for customers, investment in customer-targeted training, and measurement of performance outputs. (SK)

Structure and electronic properties of grain boundaries in earth-abundant photovoltaic absorber Cu2ZnSnSe4.

Science.gov (United States)

Li, Junwen; Mitzi, David B; Shenoy, Vivek B

2011-11-22

We have studied the atomic and electronic structure of Cu(2)ZnSnSe(4) and CuInSe(2) grain boundaries using first-principles calculations. We find that the constituent atoms at the grain boundary in Cu(2)ZnSnSe(4) create localized defect states that promote the recombination of photon-excited electron and hole carriers. In distinct contrast, significantly lower density of defect states is found at the grain boundaries in CuInSe(2), which is consistent with the experimental observation that CuInSe(2) solar cells exhibit high conversion efficiency without the need for deliberate passivation. Our investigations suggest that it is essential to effectively remove these defect states in order to improve the conversion efficiency of solar cells with Cu(2)ZnSnSe(4) as photovoltaic absorber materials. © 2011 American Chemical Society

Determination of grain boundary mobility during recrystallization by statistical evaluation of electron backscatter diffraction measurements

International Nuclear Information System (INIS)

Basu, I.; Chen, M.; Loeck, M.; Al-Samman, T.; Molodov, D.A.

2016-01-01

One of the key aspects influencing microstructural design pathways in metallic systems is grain boundary motion. The present work introduces a method by means of which direct measurement of grain boundary mobility vs. misorientation dependence is made possible. The technique utilizes datasets acquired by means of serial electron backscatter diffraction (EBSD) measurements. The experimental EBSD measurements are collectively analyzed, whereby datasets were used to obtain grain boundary mobility and grain aspect ratio with respect to grain boundary misorientation. The proposed method is further validated using cellular automata (CA) simulations. Single crystal aluminium was cold rolled and scratched in order to nucleate random orientations. Subsequent annealing at 300 °C resulted in grains growing, in the direction normal to the scratch, into a single deformed orientation. Growth selection was observed, wherein the boundaries with misorientations close to Σ7 CSL orientation relationship (38° 〈111〉) migrated considerably faster. The obtained boundary mobility distribution exhibited a non-monotonic behavior with a maximum corresponding to misorientation of 38° ± 2° about 〈111〉 axes ± 4°, which was 10–100 times higher than the mobility values of random high angle boundaries. Correlation with the grain aspect ratio values indicated a strong growth anisotropy displayed by the fast growing grains. The observations have been discussed in terms of the influence of grain boundary character on grain boundary motion during recrystallization. - Highlights: • Statistical microstructure method to measure grain boundary mobility during recrystallization • Method implementation independent of material or crystal structure • Mobility of the Σ7 boundaries in 5N Al was calculated as 4.7 × 10"–"8 m"4/J ⋅ s. • Pronounced growth selection in the recrystallizing nuclei in Al • Boundary mobility values during recrystallization 2–3 orders of magnitude

Application of Electron Backscattered Diffraction (EBSD) and Atomic Force Microscopy (AFM) to Determine Texture, Mesotexture, and Grain Boundary Energies in Ceramics

International Nuclear Information System (INIS)

Glass, S.J.; Rohrer, G.S.; Saylor, D.M.; Vedula, V.R.

1999-01-01

Crystallographic orientations in alumina (Al 2 0 3 ) and magnesium aluminate spinel (MgAl 2 0 4 ) were obtained using electron backscattered diffraction (EBSD) patterns. The texture and mesotexture (grain boundary mis-orientations) were random and no special boundaries were observed. The relative grain boundary energies were determined by thermal groove geometries using atomic force microscopy (AFM) to identify relationships between the grain boundary energies and mis-orientations

Polarization reversal of electron cyclotron wave due to radial boundary condition

International Nuclear Information System (INIS)

Takahashi, K.; Kaneko, T.; Hatakeyama, R.

2004-01-01

The electron cyclotron wave is an important plasma wave in the fields of basic plasma physics and nuclear fusion. Propagation and absorption of electromagnetic waves with electron cyclotron resonance (ECR) frequency are experimentally and theoretically investigated for the case of inhomogeneously magnetized plasma column with peripheral vacuum layer, when a left-hand polarized wave (LHPW) is selectively launched. The polarization reversal from the LHPW to the right-hand polarized wave is found to occur near the ECR point. As a result, it is clarified that the LHPW, which has been considered not to be absorbed at the ECR point, is absorbed near the ECR point. The phenomena can be explained by taking into account the effects of the radial boundary conditions. In addition, it is found that the polarization reversal point can be adjusted by the external parameters, for example, plasma radius. (authors)

Electron temperature gradient driven instability in the tokamak boundary plasma

International Nuclear Information System (INIS)

Xu, X.Q.; Rosenbluth, M.N.; Diamond, P.H.

1992-01-01

A general method is developed for calculating boundary plasma fluctuations across a magnetic separatrix in a tokamak with a divertor or a limiter. The slab model, which assumes a periodic plasma in the edge reaching the divertor or limiter plate in the scrape-off layer(SOL), should provide a good estimate, if the radial extent of the fluctuation quantities across the separatrix to the edge is small compared to that given by finite particle banana orbit. The Laplace transform is used for solving the initial value problem. The electron temperature gradient(ETG) driven instability is found to grow like t -1/2 e γmt

USE OF ELECTRONIC EDUCATIONAL RESOURCES WHEN TRAINING IN WORK WITH SPREADSHEETS

Directory of Open Access Journals (Sweden)

Х А Гербеков

2017-12-01

Full Text Available Today the tools for maintaining training courses based on opportunities of information and communication technologies are developed. Practically in all directions of preparation and on all subject matters electronic textbook and self-instruction manuals are created. Nevertheless the industry of computer educational and methodical materials actively develops and gets more and more areas of development and introduction. In this regard more and more urgent is a problem of development of the electronic educational resources adequate to modern educational requirements. Creation and the organization of training courses with use of electronic educational resources in particular on the basis of Internet technologies remains a difficult methodical task.In article the questions connected with development of electronic educational resources for use when studying the substantial line “Information technologies” of a school course of informatics in particular for studying of spreadsheets are considered. Also the analysis of maintenance of a school course and the unified state examination from the point of view of representation of task in him corresponding to the substantial line of studying “Information technologies” on mastering technology of information processing in spreadsheets and the methods of visualization given by means of charts and schedules is carried out.

Analytical Study of Usage of Electronic Information Resources at Pharmacopoeial Libraries in India

Directory of Open Access Journals (Sweden)

Sunil Tyagi

2014-02-01

Full Text Available The objective of this study is to know the rate and purpose of the use of e-resource by the scientists at pharmacopoeial libraries in India. Among other things, this study examined the preferences of the scientists toward printed books and journals, electronic information resources, and pattern of using e-resources. Non-probability sampling specially accidental and purposive technique was applied in the collection of primary data through administration of user questionnaire. The sample respondents chosen for the study consists of principle scientific officer, senior scientific officer, scientific officer, and scientific assistant of different division of the laboratories, namely, research and development, pharmaceutical chemistry, pharmacovigilance, pharmacology, pharmacogonosy, and microbiology. The findings of the study reveal the personal experiences and perceptions they have had on practice and research activity using e-resource. The major findings indicate that of the total anticipated participants, 78% indicated that they perceived the ability to use computer for electronic information resources. The data analysis shows that all the scientists belonging to the pharmacopoeial libraries used electronic information resources to address issues relating to drug indexes and compendia, monographs, drugs obtained through online databases, e-journals, and the Internet sources—especially polices by regulatory agencies, contacts, drug promotional literature, and standards.

Page 170 Use of Electronic Resources by Undergraduates in Two ...

African Journals Online (AJOL)

undergraduate students use electronic resources such as NUC virtual library, HINARI, ... web pages articles from magazines, encyclopedias, pamphlets and other .... of Nigerian university libraries have Internet connectivity, some of the system.

Model of e-learning with electronic educational resources of new generation

Directory of Open Access Journals (Sweden)

A. V. Loban

2017-01-01

Full Text Available Purpose of the article: improving of scientific and methodical base of the theory of the е-learning of variability. Methods used: conceptual and logical modeling of the е-learning of variability process with electronic educational resource of new generation and system analysis of the interconnection of the studied subject area, methods, didactics approaches and information and communication technologies means. Results: the formalization complex model of the е-learning of variability with electronic educational resource of new generation is developed, conditionally decomposed into three basic components: the formalization model of the course in the form of the thesaurusclassifier (“Author of e-resource”, the model of learning as management (“Coordination. Consultation. Control”, the learning model with the thesaurus-classifier (“Student”. Model “Author of e-resource” allows the student to achieve completeness, high degree of didactic elaboration and structuring of the studied material in triples of variants: modules of education information, practical task and control tasks; the result of the student’s (author’s of e-resource activity is the thesaurus-classifier. Model of learning as management is based on the principle of personal orientation of learning in computer environment and determines the logic of interaction between the lecturer and the student when determining the triple of variants individually for each student; organization of a dialogue between the lecturer and the student for consulting purposes; personal control of the student’s success (report generation and iterative search for the concept of the class assignment in the thesaurus-classifier before acquiring the required level of training. Model “Student” makes it possible to concretize the learning tasks in relation to the personality of the student and to the training level achieved; the assumption of the lecturer about the level of training of a

A survey of the use of electronic scientific information resources among medical and dental students

Directory of Open Access Journals (Sweden)

Aarnio Matti

2006-05-01

Full Text Available Abstract Background To evaluate medical and dental students' utilization of electronic information resources. Methods A web survey sent to 837 students (49.9% responded. Results Twenty-four per cent of medical students and ninteen per cent of dental students searched MEDLINE 2+ times/month for study purposes, and thiry-two per cent and twenty-four per cent respectively for research. Full-text articles were used 2+ times/month by thirty-three per cent of medical and ten per cent of dental students. Twelve per cent of respondents never utilized either MEDLINE or full-text articles. In multivariate models, the information-searching skills among students were significantly associated with use of MEDLINE and full-text articles. Conclusion Use of electronic resources differs among students. Forty percent were non-users of full-text articles. Information-searching skills are correlated with the use of electronic resources, but the level of basic PC skills plays not a major role in using these resources. The student data shows that adequate training in information-searching skills will increase the use of electronic information resources.

Access to electronic information resources by students of federal ...

African Journals Online (AJOL)

The paper discusses access to electronic information resources by students of Federal Colleges of Education in Eha-Amufu and Umunze. Descriptive survey design was used to investigate sample of 526 students. Sampling technique used was a Multi sampling technique. Data for the study were generated using ...

Adoption and use of electronic information resources by medical ...

African Journals Online (AJOL)

This study investigated the adoption and use of electronic information resources by medical science students of the University of Benin. The descriptive survey research design was adopted for the study and 390 students provided the data. Data collected were analysed with descriptive Statistics(Simple percentage and ...

Cal State Park Boundaries 2011/2012

Data.gov (United States)

California Natural Resource Agency — This is a GIS version of California State Park (CSP) operational boundaries and does not represent official property boundary determinations. This GIS version is...

Where Do Electronic Books Fit in the College Research Arsenal of Resources?

Science.gov (United States)

Barbier, Patricia

2007-01-01

Student use of electronic books has become an accepted supplement to traditional resources. Student use and satisfaction was monitored through an online course discussion board. Increased use of electronic books indicate this service is an accepted supplement to the print book collection.

Strategy Dynamics through a Demand-Based Lens: The Evolution of Market Boundaries, Resource Rents and Competitive Positions

OpenAIRE

Adner, Ron; Zemsky, Peter

2003-01-01

We develop a novel approach to the dynamics of business strategy that is grounded in an explicit treatment of consumer choice when technologies improve over time. We address the evolution of market boundaries, resource rents and competitive positions by adapting models of competition with differentiated products. Our model is consistent with the central strategy assertion that competitive interactions are governed by superior value creation and competitive advantage. More importantly, it show...

Variations in plasma wave intensity with distance along the electron foreshock boundary at Venus

Science.gov (United States)

Crawford, G. K.; Strangeway, R. J.; Russell, C. T.

1991-01-01

Plasma waves are observed in the solar wind upstream of the Venus bow shock by the Pioneer Venus Orbiter. These wave signatures occur during periods when the interplanetary magnetic field through the spacecraft position intersects the bow shock, thereby placing the spacecraft in the foreshock region. Wave intensity is analyzed as a function of distance along the electron foreshock boundary. It is found that the peak wave intensity may increase along the foreshock boundary from the tangent point to a maximum value at several Venus radii, then decrease in intensity with subsequent increase in distance. These observations could be associated with the instability process: the instability of the distribution function increasing with distance from the tangent point to saturation at the peak. Thermalization of the beam for distances beyond this point could reduce the distribution function instability resulting in weaker wave signatures.

Structure, electronic properties, and oxygen incorporation/diffusion characteristics of the Σ 5 TiN(310)[001] tilt grain boundary

Science.gov (United States)

McKenna, Keith P.

2018-02-01

First principles calculations are employed to investigate the structure, electronic properties, and oxygen incorporation/diffusion characteristics of the Σ 5 TiN(310) tilt grain boundary with relevance to applications of polycrystalline TiN in microelectronics and protective coatings. We show that the grain boundary does not significantly modify electronic states near the Fermi energy but does induce an upward shift of up to 0.6 eV in a number of deeper occupied bands. We also show that oxygen is preferentially incorporated into the TiN grain boundary (GB) but must overcome relatively high activation energies for further diffusion. These predictions are consistent with the "stuffed barrier model" proposed to explain the good barrier characteristics of TiN. We also show that while the oxidizing power of TiN GBs is not sufficient to reduce HfO2 (a prototypical gate dielectric material), they can act as a scavenger for interstitial oxygen. Altogether, these results provide the much needed atomistic insights into the properties of a model GB in TiN and suggest a number of directions for future investigation.

Strategic Planning for Electronic Resources Management: A Case Study at Gustavus Adolphus College

Science.gov (United States)

Hulseberg, Anna; Monson, Sarah

2009-01-01

Electronic resources, the tools we use to manage them, and the needs and expectations of our users are constantly evolving; at the same time, the roles, responsibilities, and workflow of the library staff who manage e-resources are also in flux. Recognizing a need to be more intentional and proactive about how we manage e-resources, the…

REVIEW OF MOODLE PLUGINS FOR DESIGNING MULTIMEDIA ELECTRONIC EDUCATIONAL RESOURCES FROM LANGUAGE DISCIPLINES

Directory of Open Access Journals (Sweden)

Anton M. Avramchuk

2015-09-01

Full Text Available Today the problem of designing multimedia electronic educational resources from language disciplines in Moodle is very important. This system has a lot of different, powerful resources, plugins to facilitate the learning of students with language disciplines. This article presents an overview and comparative analysis of the five Moodle plugins for designing multimedia electronic educational resources from language disciplines. There have been considered their key features and functionality in order to choose the best for studying language disciplines in the Moodle. Plugins are compared by a group of experts according to the criteria: efficiency, functionality and easy use. For a comparative analysis of the plugins it is used the analytic hierarchy process.

DNR Division of Parks and Trails District Boundaries

Data.gov (United States)

Minnesota Department of Natural Resources — This data shows the DNR Division of Parks and Trails District Boundaries as of May 2010. The boundaries were created by the Division Leadership Team. Boundaries are...

Engineering Mixed Ionic Electronic Conduction in La 0.8 Sr 0.2 MnO 3+ δ Nanostructures through Fast Grain Boundary Oxygen Diffusivity

KAUST Repository

Saranya, Aruppukottai M.; Pla, Dolors; Morata, Alex; Cavallaro, Andrea; Canales-Vá zquez, Jesú s; Kilner, John A.; Burriel, Mó nica; Tarancó n, Albert

2015-01-01

to implement in nanostructures. Here, an artificial mixed ionic electronic conducting oxide is fabricated by grain boundary (GB) engineering thin films of La0.8Sr0.2MnO3+δ. This electronic conductor is converted into a good mixed ionic electronic conductor

Modern ICT Tools: Online Electronic Resources Sharing Using Web ...

African Journals Online (AJOL)

Modern ICT Tools: Online Electronic Resources Sharing Using Web 2.0 and Its Implications For Library And Information Practice In Nigeria. ... The PDF file you selected should load here if your Web browser has a PDF reader plug-in installed (for example, a recent version of Adobe Acrobat Reader). If you would like more ...

THE MODEL OF LINGUISTIC TEACHERS’ COMPETENCY DEVELOPMENT ON DESIGNING MULTIMEDIA ELECTRONIC EDUCATIONAL RESOURCES IN THE MOODLE SYSTEM

Directory of Open Access Journals (Sweden)

Anton M. Avramchuk

2017-10-01

Full Text Available The article is devoted to the problem of developing the competency of teachers of language disciplines on designing multimedia electronic educational resources in the Moodle system. The concept of "the competence of teachers of language disciplines on designing multimedia electronic educational resources in the Moodle system" is justified and defined. Identified and characterized the components by which the levels of the competency development of teachers of language disciplines on designing multimedia electronic educational resources in the Moodle system should be assessed. Developed a model for the development of the competency of teachers of language disciplines on designing multimedia electronic educational resources in the Moodle system, which is based on the main scientific approaches, used in adult education, and consists of five blocks: target, informative, technological, diagnostic and effective.

Developing Humanities Collections in the Digital Age: Exploring Humanities Faculty Engagement with Electronic and Print Resources

Science.gov (United States)

Kachaluba, Sarah Buck; Brady, Jessica Evans; Critten, Jessica

2014-01-01

This article is based on quantitative and qualitative research examining humanities scholars' understandings of the advantages and disadvantages of print versus electronic information resources. It explores how humanities' faculty members at Florida State University (FSU) use print and electronic resources, as well as how they perceive these…

National Forest Boundaries

Data.gov (United States)

Minnesota Department of Natural Resources — This theme shows the USFS national forest boundaries in the state. This data was acquired from the GIS coordinators at both the Chippewa National Forest and the...

Electron temperature gradient mode instability and stationary vortices with elliptic and circular boundary conditions in non-Maxwellian plasmas

Energy Technology Data Exchange (ETDEWEB)

Haque, Q. [Theoretical Physics Division, PINSTECH, P.O. Nilore, Islamabad (Pakistan); Zakir, U. [Department of Physics, University of Peshawar, Khyber Pakhtun Khwa 25000 (Pakistan); Department of Physics, University of Malakand, Khyber Pakhtun Khwa 18800 (Pakistan); Qamar, A. [Department of Physics, University of Peshawar, Khyber Pakhtun Khwa 25000 (Pakistan)

2015-12-15

Linear and nonlinear dynamics of electron temperature gradient mode along with parallel electron dynamics is investigated by considering hydrodynamic electrons and non-Maxwellian ions. It is noticed that the growth rate of η{sub e}-mode driven linear instability decreases by increasing the value of spectral index and increases by reducing the ion/electron temperature ratio along the magnetic field lines. The eigen mode dispersion relation is also found in the ballooning mode limit. Stationary solutions in the form of dipolar vortices are obtained for both circular and elliptic boundary conditions. It is shown that the dynamics of both circular and elliptic vortices changes with the inclusion of inhomogeneity and non-Maxwellian effects.

Electron temperature gradient mode instability and stationary vortices with elliptic and circular boundary conditions in non-Maxwellian plasmas

Science.gov (United States)

Haque, Q.; Zakir, U.; Qamar, A.

2015-12-01

Linear and nonlinear dynamics of electron temperature gradient mode along with parallel electron dynamics is investigated by considering hydrodynamic electrons and non-Maxwellian ions. It is noticed that the growth rate of ηe-mode driven linear instability decreases by increasing the value of spectral index and increases by reducing the ion/electron temperature ratio along the magnetic field lines. The eigen mode dispersion relation is also found in the ballooning mode limit. Stationary solutions in the form of dipolar vortices are obtained for both circular and elliptic boundary conditions. It is shown that the dynamics of both circular and elliptic vortices changes with the inclusion of inhomogeneity and non-Maxwellian effects.

Nanocrystalline CsPbBr3 thin films: a grain boundary opto-electronic study

Science.gov (United States)

Conte, G.; Somma, F.; Nikl, M.

2005-01-01

CsPbBr3 thin films with nanocrystalline morphology were studied by using optoelectronic techniques to infer the grain boundary region in respect of the crystallite's interior performance. Co-evaporation of puri-fied powders or crushed Bridgman single crystals were used to deposit materials and compare recombina-tion mechanism and dielectric relaxation processes within them. Nanosecond photoconduction decay was observed on both materials as well as activated hopping transport. An asymmetric Debye-like peak was evaluated from impedance spectroscopy with a FWHM value, which remains constant for 1.25 +/- 0.02 deca-des, addressing the presence of a tight conductivity relaxation times distribution. The evaluated activation energy, equal to 0.72 +/- 0.05 eV, similar to that estimated by DC measurements, is well smaller then that expected for an intrinsic material with exciton absorption at 2.36 eV. A simple model based on Voigt's elements was used to model the electronic characteristics of these nanostructured materials, to discuss observed results and define the role played by grain boundaries.

Electronic resource management systems a workflow approach

CERN Document Server

Anderson, Elsa K

2014-01-01

To get to the bottom of a successful approach to Electronic Resource Management (ERM), Anderson interviewed staff at 11 institutions about their ERM implementations. Among her conclusions, presented in this issue of Library Technology Reports, is that grasping the intricacies of your workflow-analyzing each step to reveal the gaps and problems-at the beginning is crucial to selecting and implementing an ERM. Whether the system will be used to fill a gap, aggregate critical data, or replace a tedious manual process, the best solution for your library depends on factors such as your current soft

Spatially resolved analytical electron microscopy at grain boundaries of {alpha}-Al{sub 2}O{sub 3}; Ortsaufgeloeste analytische Elektronenmikroskopie an Korngrenzen in {alpha}Al{sub 2}O{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Nufer, S.

2001-10-01

Aluminum oxide, {alpha}-Al{sub 2}O{sub 3}, is a common structural ceramic material. The most technologically important properties are either determined or strongly influenced by the polycrystalline microstructure. For instance, the grain boundaries control the mechanical behavior (e.g. plasticity, creep, and fracture) or various transport phenomena (e.g. ion diffusion, segregation, and electrical resistivity). In order to understand the structure-properties relationships, it is therefore important to characterize the structure and chemistry of grain boundaries, both experimentally and theoretically. In this work the electronic structure of the basal and rhombohedral twin grain boundaries and the impurity excess at different tilt grain boundaries in bicrystals were investigated, using electron energy-loss spectroscopy (EELS) and energy dispersive X-ray spectroscopy (EDXS). The electronic structure of the rhombohedral twin grain boundary was determined by comparing spatially resolved EELS measurements of the O-K ionisation edge with the theoretical density of states (DOS), obtained from local density functional theory (LDFT) calculations. The interface excess of impurities was quantitatively analysed at grain boundaries with and without Y-doping. (orig.)

Electronic Resource Management System. Vernetzung von Lizenzinformationen

Directory of Open Access Journals (Sweden)

Michaela Selbach

2014-12-01

Full Text Available In den letzten zehn Jahren spielen elektronische Ressourcen im Bereich der Erwerbung eine zunehmend wichtige Rolle: Eindeutig lässt sich hier ein Wandel in den Bibliotheken (fort vom reinen Printbestand zu immer größeren E-Only-Beständen feststellen. Die stetig wachsende Menge an E-Ressourcen und deren Heterogenität stellt Bibliotheken vor die Herausforderung, die E-Ressourcen effizient zu verwalten. Nicht nur Bibliotheken, sondern auch verhandlungsführende Institutionen von Konsortial- und Allianzlizenzen benötigen ein geeignetes Instrument zur Verwaltung von Lizenzinformationen, welches den komplexen Anforderungen moderner E-Ressourcen gerecht wird. Die Deutsche Forschungsgemeinschaft (DFG unterstützt ein Projekt des Hochschulbibliothekszentrums des Landes Nordrhein-Westfalen (hbz, der Universitätsbibliothek Freiburg, der Verbundzentrale des Gemeinsamen Bibliotheksverbundes (GBV und der Universitätsbibliothek Frankfurt, in dem ein bundesweit verfügbares Electronic Ressource Managementsystem (ERMS aufgebaut werden soll. Ein solches ERMS soll auf Basis einer zentralen Knowledge Base eine einheitliche Nutzung von Daten zur Lizenzverwaltung elektronischer Ressourcen auf lokaler, regionaler und nationaler Ebene ermöglichen. Statistische Auswertungen, Rechteverwaltung für alle angeschlossenen Bibliotheken, kooperative Datenpflege sowie ein über standardisierte Schnittstellen geführter Datenaustausch stehen bei der Erarbeitung der Anforderungen ebenso im Fokus wie die Entwicklung eines Daten- und Funktionsmodells. In the last few years the importance of electronic resources in library acquisitions has increased significantly. There has been a shift from mere print holdings to both e- and print combinations and even e-only subscriptions. This shift poses a double challenge for libraries: On the one hand they have to provide their e-resource collections to library users in an appealing way, on the other hand they have to manage these

Sierra Nevada Subregional Boundary - Sierra Nevada Conservancy [ds542

Data.gov (United States)

California Natural Resource Agency — Sierra Nevada Conservancy (SNC) boundary. The boundary was mapped to correspond with statute AB 2600 (2004) and as re-defined in AB 1201 (2005). Work on the boundary...

The Electron Microscopy Outreach Program: A Web-based resource for research and education.

Science.gov (United States)

Sosinsky, G E; Baker, T S; Hand, G; Ellisman, M H

1999-01-01

We have developed a centralized World Wide Web (WWW)-based environment that serves as a resource of software tools and expertise for biological electron microscopy. A major focus is molecular electron microscopy, but the site also includes information and links on structural biology at all levels of resolution. This site serves to help integrate or link structural biology techniques in accordance with user needs. The WWW site, called the Electron Microscopy (EM) Outreach Program (URL: http://emoutreach.sdsc.edu), provides scientists with computational and educational tools for their research and edification. In particular, we have set up a centralized resource containing course notes, references, and links to image analysis and three-dimensional reconstruction software for investigators wanting to learn about EM techniques either within or outside of their fields of expertise. Copyright 1999 Academic Press.

Minnesota County Boundaries

Data.gov (United States)

Minnesota Department of Natural Resources — Minnesota county boundaries derived from a combination of 1:24,000 scale PLS lines, 1:100,000 scale TIGER, 1:100,000 scale DLG, and 1:24,000 scale hydrography lines....

Technical Communicator: A New Model for the Electronic Resources Librarian?

Science.gov (United States)

Hulseberg, Anna

2016-01-01

This article explores whether technical communicator is a useful model for electronic resources (ER) librarians. The fields of ER librarianship and technical communication (TC) originated and continue to develop in relation to evolving technologies. A review of the literature reveals four common themes for ER librarianship and TC. While the…

Nanocompositional Electron Microscopic Analysis and Role of Grain Boundary Phase of Isotropically Oriented Nd-Fe-B Magnets

Directory of Open Access Journals (Sweden)

Gregor A. Zickler

2017-01-01

Full Text Available Nanoanalytical TEM characterization in combination with finite element micromagnetic modelling clarifies the impact of the grain misalignment and grain boundary nanocomposition on the coercive field and gives guidelines how to improve coercivity in Nd-Fe-B based magnets. The nanoprobe electron energy loss spectroscopy measurements obtained an asymmetric composition profile of the Fe-content across the grain boundary phase in isotropically oriented melt-spun magnets and showed an enrichment of iron up to 60 at% in the Nd-containing grain boundaries close to Nd2Fe14B grain surfaces parallel to the c-axis and a reduced iron content up to 35% close to grain surfaces perpendicular to the c-axis. The numerical micromagnetic simulations on isotropically oriented magnets using realistic model structures from the TEM results reveal a complex magnetization reversal starting at the grain boundary phase and show that the coercive field increases compared to directly coupled grains with no grain boundary phase independently of the grain boundary thickness. This behaviour is contrary to the one in aligned anisotropic magnets, where the coercive field decreases compared to directly coupled grains with an increasing grain boundary thickness, if Js value is > 0.2 T, and the magnetization reversal and expansion of reversed magnetic domains primarily start as Bloch domain wall at grain boundaries at the prismatic planes parallel to the c-axis and secondly as Néel domain wall at the basal planes perpendicular to the c-axis. In summary our study shows an increase of coercive field in isotropically oriented Nd-Fe-B magnets for GB layer thickness > 5 nm and an average Js value of the GB layer < 0.8 T compared to the magnet with perfectly aligned grains.

State Park Statutory Boundaries

Data.gov (United States)

Minnesota Department of Natural Resources — Legislative statutory boundaries for sixty six state parks, six state recreation areas, and eight state waysides. These data are derived principally from DNR's...

MODEL OF AN ELECTRONIC EDUCATIONAL RESOURCE OF NEW GENERATION

Directory of Open Access Journals (Sweden)

Anatoliy V. Loban

2016-01-01

Full Text Available The mathematical structure of the modular architecture of an electronic educational resource (EER of new generation, which allows to decompose the process of studying the subjects of the course at a hierarchically ordered set of data (knowledge and procedures for manipulating them, to determine the roles of participants of process of training of and technology the development and use of EOR in the study procrate.

Electron-beam-induced current study of small-angle grain boundaries in multicrystalline silicon

International Nuclear Information System (INIS)

Chen, J.; Sekiguchi, T.; Xie, R.; Ahmet, P.; Chikyo, T.; Yang, D.; Ito, S.; Yin, F.

2005-01-01

Recombination activity of small-angle grain boundaries (SA GBs) in multicrystalline silicon (mc-Si) was studied by means of electron-beam-induced current (EBIC) technique. In the as-grown mc-Si, the EBIC contrasts of special Σ and random GBs were weak at both 300 and 100 K, whereas those of SA GBs were weak (<3%) at 300 K and strong (30-40%) at 100 K. In the contaminated mc-Si, SA GBs showed stronger EBIC contrast than Σ and R GBs at 300 K. It is indicated that SA GBs possess high density of shallow levels and are easily contaminated with Fe compared to other GBs

Analysis of grain boundaries, twin boundaries, and Te precipitates in CdZnTe grown by high-pressure Bridgeman method

International Nuclear Information System (INIS)

Heffelfinger, J.R.; Medlin, D.L.; James, R.B.

1998-03-01

Grain boundaries and twin boundaries in commercial Cd 1-x Zn x Te, which is prepared by a high pressure Bridgeman technique, have been investigated with transmission electron microscopy, scanning electron microscopy, infrared light microscopy and visible light microscopy. Boundaries inside these materials were found to be decorated with Te precipitates. The shape and local density of the precipitates were found to depend on the particular boundary. For precipitates that decorate grain boundaries, their microstructure was found to consist of a single, saucer shaped grain of hexagonal Te (space group P3 1 21). Analysis of a Te precipitate precipitates by selected area diffraction revealed the Te to be aligned with the surrounding Cd 1-x Zn x Te grains. This alignment was found to match the (111) Cd 1-x Z x Te planes with the (1 bar 101) planes of hexagonal Te. Crystallographic alignments between the Cd 1-x Zn x Te grains were also observed for a high angle grain boundary. The structure of the grain boundaries and the Te/Cd 1-x Zn x Te interface are discussed

Grain boundaries in high temperature superconductors

NARCIS (Netherlands)

Hilgenkamp, Johannes W.M.; Mannhart, J.

2002-01-01

Since the first days of high-Tc superconductivity, the materials science and the physics of grain boundaries in superconducting compounds have developed into fascinating fields of research. Unique electronic properties, different from those of the grain boundaries in conventional metallic

Boundary organizations to boundary chains: Prospects for advancing climate science application

Directory of Open Access Journals (Sweden)

Christine J. Kirchhoff

2015-01-01

Full Text Available Adapting to climate change requires the production and use of climate information to inform adaptation decisions. By facilitating sustained interaction between science producers, boundary organizations narrow the gap between science and decision-making and foster the co-production of actionable knowledge. While traditional boundary organization approaches focused on intense one-on-one interactions between producers and users increases usability, this approach requires significant time and resources. Forming “boundary chains”, linking complimentary boundary organizations together, may reduce those costs. In this paper, we use longitudinal observations of a boundary chain, interviews and surveys to explore: (1 how producer-user interactions increase understanding and information usability and (2 if and how efficiencies in climate information production, dissemination and use arise as a result of the boundary chain. We find that forming and sustaining an effective boundary chain requires not only interest, commitment and investment from every link in the chain but also a level of non-overlapping mutual dependency and complementary skill sets. In this case, GLISA’s strength in producing scientific information and their credibility as climate scientists and HRWC’s strengths in facilitation, connection with potential information users, and their recognition and reputation in the watershed add value to the boundary chain enabling the boundary chain to accomplish more with greater efficiency than if each organization in the chain tried to work independently. Finally, data show how the boundary chain increased efficiencies in educating potential users about the strengths and limitations of climate science and improving the production, dissemination, and use of climate information.

Study on resources and environmental data integration towards data warehouse construction covering trans-boundary area of China, Russia and Mongolia

Science.gov (United States)

Wang, J.; Song, J.; Gao, M.; Zhu, L.

2014-02-01

The trans-boundary area between Northern China, Mongolia and eastern Siberia of Russia is a continuous geographical area located in north eastern Asia. Many common issues in this region need to be addressed based on a uniform resources and environmental data warehouse. Based on the practice of joint scientific expedition, the paper presented a data integration solution including 3 steps, i.e., data collection standards and specifications making, data reorganization and process, data warehouse design and development. A series of data collection standards and specifications were drawn up firstly covering more than 10 domains. According to the uniform standard, 20 resources and environmental survey databases in regional scale, and 11 in-situ observation databases were reorganized and integrated. North East Asia Resources and Environmental Data Warehouse was designed, which included 4 layers, i.e., resources layer, core business logic layer, internet interoperation layer, and web portal layer. The data warehouse prototype was developed and deployed initially. All the integrated data in this area can be accessed online.

Study on resources and environmental data integration towards data warehouse construction covering trans-boundary area of China, Russia and Mongolia

International Nuclear Information System (INIS)

Wang, J; Song, J; Gao, M; Zhu, L

2014-01-01

The trans-boundary area between Northern China, Mongolia and eastern Siberia of Russia is a continuous geographical area located in north eastern Asia. Many common issues in this region need to be addressed based on a uniform resources and environmental data warehouse. Based on the practice of joint scientific expedition, the paper presented a data integration solution including 3 steps, i.e., data collection standards and specifications making, data reorganization and process, data warehouse design and development. A series of data collection standards and specifications were drawn up firstly covering more than 10 domains. According to the uniform standard, 20 resources and environmental survey databases in regional scale, and 11 in-situ observation databases were reorganized and integrated. North East Asia Resources and Environmental Data Warehouse was designed, which included 4 layers, i.e., resources layer, core business logic layer, internet interoperation layer, and web portal layer. The data warehouse prototype was developed and deployed initially. All the integrated data in this area can be accessed online

Diamagnetic boundary layers: a kinetic theory

International Nuclear Information System (INIS)

Lemaire, J.; Burlaga, L.F.

1976-01-01

A kinetic theory for boundary layers associated with MHD tangential 'discontinuities' in a collisionless magnetized plasma such as those observed in the solar wind is presented. The theory consists of finding self-consistent solutions of Vlasov's equation and Maxwell's equation for stationary, one-dimensional boundary layers separating two Maxwellian plasma states. Layers in which the current is carried by electrons are found to have a thickness of the order of a few electron gyroradii, but the drift speed of the current-carrying electrons is found to exceed the Alfven speed, and accordingly such layers are not stable. Several types of layers, in which the current is carried by protons are discussed; in particular, cases in which the magnetic field intensity and/or direction changed across the layer were considered. In every case, the thickness was of the order of a few proton gyroradii and the field changed smoothly , although the characteristics depended somewhat on the boundary conditions. The drift speed was always less than the Alfven speed, consistent with stability of such structures. The results are consistent with the observations of boundary layers in the solar wind near 1 AU. (Auth.)

Usage and efficacy of electronic dictionaries for a language without word boundaries

Directory of Open Access Journals (Sweden)

Etsuko Toyoda

2016-09-01

Full Text Available There is cumulative evidence suggesting that hyper-glossing facilitates lower-level processing and enhances reading comprehension. There are plentiful studies on electronic dictionaries for English. However, research on e-dictionaries for languages with no boundaries between words is still scarce. The main aim for the current study is to investigate the usage and efficacy of e-dictionaries for Japanese language learners. This article reports the results of two studies concerning e-dictionaries: a survey study investigating the use of e-dictionaries (with a particular focus on e-glossaries that change a digital text into a hypertext by L2 learners of Japanese, and a comparative study examining existing e-glossaries to evaluate whether they provide the optimal level of support for reading Japanese e-texts. The results of the survey showed that learners have their preferred e-dictionaries (in most cases, e-word dictionaries in which the user can look up individual words, and that few learners are aware of the existence of e-glossaries. The results of further study revealed that existing e-glossaries have various functions, but lack some requisite information crucial to the target language. This study suggests that technical issues revolving around the lack of spaces between words may be a reason for the lag in usage and efficacy of e-glossaries for languages without word boundaries.

Minnesota County Boundaries - lines

Data.gov (United States)

Minnesota Department of Natural Resources — Minnesota county boundaries derived from a combination of 1:24,000 scale PLS lines, 1:100,000 scale TIGER, 1:100,000 scale DLG, and 1:24,000 scale hydrography lines....

Crossing Boundaries in Global Software Development

DEFF Research Database (Denmark)

Søderberg, Anne-Marie; Romani, Laurence

across cultures, languages, organizational boundaries, time zones and geographical distances. The paper revises a framework of boundary spanning leadership practices developed for MNCs and adapts it to an offshore outsourcing context. It also contributes with reflections on how imbalances of resources......Western companies´ offshore outsourcing is increasingly being replaced by strategic partnerships that require closer collaboration between client and vendor. This paper addresses the question: How does a vendor company from an emergent market deal with inter-organizational boundary spanning...

GUIDELINES FOR EVALUATION OF PSYCHOLOGICAL AND PEDAGOGICAL QUALITY CHARACTERISTICS OF ELECTRONIC EDUCATIONAL RESOURCES

Directory of Open Access Journals (Sweden)

Galina P. Lavrentieva

2014-05-01

Full Text Available The article highlights the causes of insufficient effective use of electronic learning resources and sets out the guidelines on ways to solve the aforementioned problems. The set of didactic, methodical, psychological, pedagogical, design and ergonomic quality requirements is considered for evaluation, selection and application of information and communication technologies in the educational process. The most appropriate mechanisms for the ICT introduction into the learning process are disclosed as it should meet the specific learning needs of the student and the objectives of the educational process. The guidance for psycho-educational assessment of quality of electronic educational resources is provided. It is argued that the effectiveness of the ICT use is to be improved by means of quality evaluation mechanisms involved into the educational process.

Dual boundary spanning

DEFF Research Database (Denmark)

Li-Ying, Jason

2016-01-01

The extant literature runs short in understanding openness of innovation regarding and the different pathways along which internal and external knowledge resources can be combined. This study proposes a unique typology for outside-in innovations based on two distinct ways of boundary spanning......: whether an innovation idea is created internally or externally and whether an innovation process relies on external knowledge resources. This yields four possible types of innovation, which represent the nuanced variation of outside-in innovations. Using historical data from Canada for 1945...

Availability, Use and Constraints to Use of Electronic Information Resources by Postgraduates Students at the University of Ibadan

Directory of Open Access Journals (Sweden)

Dare Samuel Adeleke

2017-12-01

Full Text Available Availability, awareness and use of electronic resources provide access to authoritative, reliable, accurate and timely access to information. The use of electronic information resources (EIRs can enable innovation in teaching and increase timeliness in research of postgraduate students which will eventual result into encouragement of the expected research-led enquiry in this digital age. The study adopted a descriptive survey design. Samples of 300 of postgraduate students within seven out 13 Faculties were randomly selected. Data were collected using questionnaire designed to elicit response from respondents and data were analyzed using descriptive statistics methods percentages, mean, and standard deviation. Results indicated that internet was ranked most available and used in the university. Low level of usage of electronic resources, in particular, full texts data bases is linked to a number of constraints: Interrupted power supply was ranked highest among other factors as speed and capacity of computers, retrieval of records with high recall and low precision, retrieving records relevant to information need, lack of knowledge of search techniques to retrieve information effectively, non possession of requisite IT skills and problems accessing the internet. The study recommended that usage of electronic resources be made compulsory, intensifying awareness campaigns concerning the availability, training on use of electronic resources and the problem of power outage be addressed.

A study on the development of automatic economic profit and loss calculation system for maritime boundary delimitation

International Nuclear Information System (INIS)

Kwak, G; Kim, K; Park, Y

2014-01-01

As the maritime boundary delimitation is important for the purpose of securing marine resources, in addition to the aspect of maritime security, interest in maritime boundary delimitation to help national benefits are increasing over the world. In Korea, the importance of maritime boundary delimitation with the neighbouring countries is also increasing in practice. The quantity of obtainable marine resources depending on maritime boundary acts as an important factor for maritime boundary delimitation. Accordingly, a study is required to calculate quantity of our obtainable marine resources depending on maritime boundary delimitation. This study intends to calculate obtainable marine resources depending on various maritime boundary scenarios insisted by several countries. It mainly aims at developing a GIS-based automation system to be utilized for decision making of the maritime boundary delimitation. For this target, it has designed a module using spatial analysis technique to automatically calculate profit and loss waters area of each country upon maritime boundary and another module to estimate economic profits and losses obtained by each country using the calculated waters area and pricing information of the marine resources. By linking both the designed modules, it has implemented an automatic economic profit and loss calculation system for the GIS-based maritime boundary delimitation. The system developed from this study automatically calculate quantity of the obtainable marine resources of a country for the maritime boundary to be added and created in the future. Thus, it is expected to support decision making for the maritime boundary negotiators

A study on the development of automatic economic profit and loss calculation system for maritime boundary delimitation

Science.gov (United States)

Kwak, G.; Kim, K.; Park, Y.

2014-02-01

As the maritime boundary delimitation is important for the purpose of securing marine resources, in addition to the aspect of maritime security, interest in maritime boundary delimitation to help national benefits are increasing over the world. In Korea, the importance of maritime boundary delimitation with the neighbouring countries is also increasing in practice. The quantity of obtainable marine resources depending on maritime boundary acts as an important factor for maritime boundary delimitation. Accordingly, a study is required to calculate quantity of our obtainable marine resources depending on maritime boundary delimitation. This study intends to calculate obtainable marine resources depending on various maritime boundary scenarios insisted by several countries. It mainly aims at developing a GIS-based automation system to be utilized for decision making of the maritime boundary delimitation. For this target, it has designed a module using spatial analysis technique to automatically calculate profit and loss waters area of each country upon maritime boundary and another module to estimate economic profits and losses obtained by each country using the calculated waters area and pricing information of the marine resources. By linking both the designed modules, it has implemented an automatic economic profit and loss calculation system for the GIS-based maritime boundary delimitation. The system developed from this study automatically calculate quantity of the obtainable marine resources of a country for the maritime boundary to be added and created in the future. Thus, it is expected to support decision making for the maritime boundary negotiators.

Studies about diffusion through grain boundary

International Nuclear Information System (INIS)

Allevato, C.E.

1983-01-01

Samples with layers of gold-silver and silver-chromium were deposited in high vacuum (10 -5 -10 -6 Torr) on glass and sodium chloride substrates. After deposition, these films were annealed at different temperatures and analysed by Rutherford Backscattering, Auger Spesctroscopy and Transmission Electron Microscopy. A simulated convolution was done using a computer in order to evalute the precision of the particle detector employed in the backscattering. The concentration profiles used to determine the diffusion coefficient were obtained by Auger electron spectroscopy. This technique demanded a study of sputtering rate to convert time of sputtering in thickness. This rate was determined by two methods. Analyses of the samples of silver-chromium, heated up to 250 0 C, by transmission electron microscopy and Auger electron spectroscopy, indicated the presence of oxide in small isolated regions, as crystallites. Values of the diffusion coefficient and activation energy related to the diffusion through the volume and by the grain boundary were determined by Suzuoka's method. The system Ag/Cr, due to its high grain boundary density, led to an increase of the diffusion coefficient so that this coefficient and the activation energy were obtained only from the grain boundary. (Author) [pt

A Study on Developing Evaluation Criteria for Electronic Resources in Evaluation Indicators of Libraries

Science.gov (United States)

Noh, Younghee

2010-01-01

This study aimed to improve the current state of electronic resource evaluation in libraries. While the use of Web DB, e-book, e-journal, and other e-resources such as CD-ROM, DVD, and micro materials is increasing in libraries, their use is not comprehensively factored into the general evaluation of libraries and may diminish the reliability of…

Beyond territory and scarcity - exploring conflicts over natural resource management

DEFF Research Database (Denmark)

Ressources management, enviromental degradation, natural resources, conflicts, boundaries, Africa......Ressources management, enviromental degradation, natural resources, conflicts, boundaries, Africa...

First-Principles Calculations of Electronic States and Self-Doping Effects at a 45° Grain Boundary in the High Temperature YBa2Cu3O7 Superconductor

KAUST Repository

Schwingenschlö gl, Udo; Schuster, Cosima

2009-01-01

The charge redistribution at grain boundaries determines the applicability of high-Tc superconductors in electronic devices because the transport across the grains can be hindered considerably. We investigate the local charge transfer and the modification of the electronic states in the vicinity of the grain-grain interface by ab initio calculations for a (normal-state) 45°-tilted [001] grain boundary in YBa2Cu3O7. Our results explain the suppressed interface transport and the influence of grain boundary doping in a quantitative manner, in accordance with the experimental situation. The charge redistribution is found to be strongly inhomogeneous, which has a substantial effect on transport properties since it gives rise to a self-doping of 0.10±0.02 holes per Cu atom.

First-Principles Calculations of Electronic States and Self-Doping Effects at a 45° Grain Boundary in the High Temperature YBa2Cu3O7 Superconductor

KAUST Repository

Schwingenschlögl, Udo

2009-06-03

The charge redistribution at grain boundaries determines the applicability of high-Tc superconductors in electronic devices because the transport across the grains can be hindered considerably. We investigate the local charge transfer and the modification of the electronic states in the vicinity of the grain-grain interface by ab initio calculations for a (normal-state) 45°-tilted [001] grain boundary in YBa2Cu3O7. Our results explain the suppressed interface transport and the influence of grain boundary doping in a quantitative manner, in accordance with the experimental situation. The charge redistribution is found to be strongly inhomogeneous, which has a substantial effect on transport properties since it gives rise to a self-doping of 0.10±0.02 holes per Cu atom.

THE MODEL OF LINGUISTIC TEACHERS’ COMPETENCY DEVELOPMENT ON DESIGNING MULTIMEDIA ELECTRONIC EDUCATIONAL RESOURCES IN THE MOODLE SYSTEM

OpenAIRE

Anton M. Avramchuk

2017-01-01

The article is devoted to the problem of developing the competency of teachers of language disciplines on designing multimedia electronic educational resources in the Moodle system. The concept of "the competence of teachers of language disciplines on designing multimedia electronic educational resources in the Moodle system" is justified and defined. Identified and characterized the components by which the levels of the competency development of teachers of language disciplines on designing ...

Quantitative Characterization of Boundary Roughness in Metals

DEFF Research Database (Denmark)

Sun, Jun

The boundary migration during recrystallization is by nature a heterogeneous process and local structural variations form on recrystallization boundaries, as revealed from modern techniques such as synchrotron X-rays and advanced electron microscopy. The local structural variations, in the form...

Determining the level of awareness of the physicians in using the variety of electronic information resources and the effecting factors.

Science.gov (United States)

Papi, Ahmad; Ghazavi, Roghayeh; Moradi, Salimeh

2015-01-01

Understanding of the medical society's from the types of information resources for quick and easy access to information is an imperative task in medical researches and management of the treatment. The present study was aimed to determine the level of awareness of the physicians in using various electronic information resources and the factors affecting it. This study was a descriptive survey. The data collection tool was a researcher-made questionnaire. The study population included all the physicians and specialty physicians of the teaching hospitals affiliated to Isfahan University of Medical Sciences and numbered 350. The sample size based on Morgan's formula was set at 180. The content validity of the tool was confirmed by the library and information professionals and the reliability was 95%. Descriptive statistics were used including the SPSS software version 19. On reviewing the need of the physicians to obtain the information on several occasions, the need for information in conducting the researches was reported by the maximum number of physicians (91.9%) and the usage of information resources, especially the electronic resources, formed 65.4% as the highest rate with regard to meeting the information needs of the physicians. Among the electronic information databases, the maximum awareness was related to Medline with 86.5%. Among the various electronic information resources, the highest awareness (43.3%) was related to the E-journals. The highest usage (36%) was also from the same source. The studied physicians considered the most effective deterrent in the use of electronic information resources as being too busy and lack of time. Despite the importance of electronic information resources for the physician's community, there was no comprehensive knowledge of these resources. This can lead to less usage of these resources. Therefore, careful planning is necessary in the hospital libraries in order to introduce the facilities and full capabilities of the

Managing Selection for Electronic Resources: Kent State University Develops a New System to Automate Selection

Science.gov (United States)

Downey, Kay

2012-01-01

Kent State University has developed a centralized system that manages the communication and work related to the review and selection of commercially available electronic resources. It is an automated system that tracks the review process, provides selectors with price and trial information, and compiles reviewers' feedback about the resource. It…

End-of-life resource recovery from emerging electronic products

DEFF Research Database (Denmark)

Parajuly, Keshav; Habib, Komal; Cimpan, Ciprian

2016-01-01

Integrating product design with appropriate end-of-life (EoL) processing is widely recognized to have huge potentials in improving resource recovery from electronic products. In this study, we investigate both the product characteristics and EoL processing of robotic vacuum cleaner (RVC), as a case...... of emerging electronic product, in order to understand the recovery fate of different materials and its linkage to product design. Ten different brands of RVC were dismantled and their material composition and design profiles were studied. Another 125 RVCs (349 kg) were used for an experimental trial...... at a conventional ‘shred-and-separate’ type preprocessing plant in Denmark. A detailed material flow analysis was performed throughout the recycling chain. The results show a mismatch between product design and EoL processing, and the lack of practical implementation of ‘Design for EoL’ thinking. In the best...

Mechanism for plasma waves at the harmonics of the plasma frequency in the electron foreshock boundary

International Nuclear Information System (INIS)

Klimas, A.J.

1983-01-01

A bump-on-tail unstable reduced velocity distribution has been constructed from data obtained at the upstream boundary of the electron foreshock by the GSFC electron spectrometer experiment on the ISEE 1 satellite. This distribution is used as the initial plasma state for a numerical integration of the one-dimensional Vlasov-Maxwell system of equations. The integration is carried through the growth of the instability, beyond its saturation, and well into the stabilized plasma regime. A power spectrum for the electric field of the stabilized plasma is computed. The spectrum is dominated by a narrow peak at the Bohm-Gross frequency of the unstable field mode but it also contain significant power at the harmonics of the Bohm-Gross frequency. The harmonic power is in sharp peaks which are split into closely spaced doublets. The fundamental peak at the Bohm-Gross frequency is also split, in this case into a closely space triplet. The fundamental peak at the Bohm-Gross frequency is also split, in this case into a closely space triplet. The splitting is due to slow modulations of the stabilized electric field oscillations which, it is thought, are caused by wave-particle trapping. The wavelength of mth harmonic of the Bohm-Gross frequency is given by lambda/sub u//m, where lambda/sub u/ is the wavelength of the unstable mode. The mechanism for excitation of the second harmonic is shwn to be second-order wave-wave coupling which takes place during that period in the evolution of the instability which would otherwise be called the linear growth phase. It is conjectured that the higher harmonics are excited by the same mechanism. It is further argued that harmonic excitation at the boundary of the electron foreshock should be a common occurrence

Use of electronic sales data to tailor nutrition education resources for an ethnically diverse population.

Science.gov (United States)

Eyles, H; Rodgers, A; Ni Mhurchu, C

2010-02-01

Nutrition education may be most effective when personally tailored. Individualised electronic supermarket sales data offer opportunities to tailor nutrition education using shopper's usual food purchases. The present study aimed to use individualised electronic supermarket sales data to tailor nutrition resources for an ethnically diverse population in a large supermarket intervention trial in New Zealand. Culturally appropriate nutrition education resources (i.e. messages and shopping lists) were developed with the target population (through two sets of focus groups) and ethnic researchers. A nutrient database of supermarket products was developed using retrospective sales data and linked to participant sales to allow tailoring by usual food purchases. Modified Heart Foundation Tick criteria were used to identify 'healthier' products in the database suitable for promotion in the resources. Rules were developed to create a monthly report listing the tailored and culturally targeted messages to be sent to each participant, and to produce automated, tailored shopping lists. Culturally targeted nutrition messages (n = 864) and shopping lists (n = 3 formats) were developed. The food and nutrient database (n = 3000 top-selling products) was created using 12 months of retrospective sales data, and comprised 60%'healthier' products. Three months of baseline sales data were used to determine usual food purchases. Tailored resources were successfully mailed to 123 Māori, 52 Pacific and 346 non-Māori non-Pacific participants over the 6-month trial intervention period. Electronic supermarket sales data can be used to tailor nutrition education resources for a large number of ethnically diverse supermarket shoppers.

Distributed resource management across process boundaries

KAUST Repository

Suresh, Lalith

2017-09-27

Multi-tenant distributed systems composed of small services, such as Service-oriented Architectures (SOAs) and Micro-services, raise new challenges in attaining high performance and efficient resource utilization. In these systems, a request execution spans tens to thousands of processes, and the execution paths and resource demands on different services are generally not known when a request first enters the system. In this paper, we highlight the fundamental challenges of regulating load and scheduling in SOAs while meeting end-to-end performance objectives on metrics of concern to both tenants and operators. We design Wisp, a framework for building SOAs that transparently adapts rate limiters and request schedulers system-wide according to operator policies to satisfy end-to-end goals while responding to changing system conditions. In evaluations against production as well as synthetic workloads, Wisp successfully enforces a range of end-to-end performance objectives, such as reducing average latencies, meeting deadlines, providing fairness and isolation, and avoiding system overload.

Distributed resource management across process boundaries

KAUST Repository

Suresh, Lalith; Bodik, Peter; Menache, Ishai; Canini, Marco; Ciucu, Florin

2017-01-01

Multi-tenant distributed systems composed of small services, such as Service-oriented Architectures (SOAs) and Micro-services, raise new challenges in attaining high performance and efficient resource utilization. In these systems, a request execution spans tens to thousands of processes, and the execution paths and resource demands on different services are generally not known when a request first enters the system. In this paper, we highlight the fundamental challenges of regulating load and scheduling in SOAs while meeting end-to-end performance objectives on metrics of concern to both tenants and operators. We design Wisp, a framework for building SOAs that transparently adapts rate limiters and request schedulers system-wide according to operator policies to satisfy end-to-end goals while responding to changing system conditions. In evaluations against production as well as synthetic workloads, Wisp successfully enforces a range of end-to-end performance objectives, such as reducing average latencies, meeting deadlines, providing fairness and isolation, and avoiding system overload.

Spatially resolved mapping of electrical conductivity across individual domain (grain) boundaries in graphene.

Science.gov (United States)

Clark, Kendal W; Zhang, X-G; Vlassiouk, Ivan V; He, Guowei; Feenstra, Randall M; Li, An-Ping

2013-09-24

All large-scale graphene films contain extended topological defects dividing graphene into domains or grains. Here, we spatially map electronic transport near specific domain and grain boundaries in both epitaxial graphene grown on SiC and CVD graphene on Cu subsequently transferred to a SiO2 substrate, with one-to-one correspondence to boundary structures. Boundaries coinciding with the substrate step on SiC exhibit a significant potential barrier for electron transport of epitaxial graphene due to the reduced charge transfer from the substrate near the step edge. Moreover, monolayer-bilayer boundaries exhibit a high resistance that can change depending on the height of substrate step coinciding at the boundary. In CVD graphene, the resistance of a grain boundary changes with the width of the disordered transition region between adjacent grains. A quantitative modeling of boundary resistance reveals the increased electron Fermi wave vector within the boundary region, possibly due to boundary induced charge density variation. Understanding how resistance change with domain (grain) boundary structure in graphene is a crucial first step for controlled engineering of defects in large-scale graphene films.

Availability, Level of Use and Constraints to Use of Electronic Resources by Law Lecturers in Public Universities in Nigeria

Science.gov (United States)

Amusa, Oyintola Isiaka; Atinmo, Morayo

2016-01-01

(Purpose) This study surveyed the level of availability, use and constraints to use of electronic resources among law lecturers in Nigeria. (Methodology) Five hundred and fifty-two law lecturers were surveyed and four hundred and forty-two responded. (Results) Data analysis revealed that the level of availability of electronic resources for the…

Grain-boundary, glassy-phase identification and possible artifacts

International Nuclear Information System (INIS)

Simpson, Y.K.; Carter, C.B.; Sklad, P.; Bentley, J.

1985-01-01

Specimen artifacts such as grain boundary grooving, surface damage of the specimen, and Si contamination are shown experimentally to arise from the ion milling used in the preparation of transmission electron microscopy specimens. These artifacts in polycrystalline, ceramic specimens can cause clean grain boundaries to appear to contain a glassy phase when the dark-field diffuse scattering technique, the Fresnel fringe technique, and analytical electron microscopy (energy dispersive spectroscopy) are used to identify glassy phases at a grain boundary. The ambiguity in interpreting each of these techniques due to the ion milling artifacts will be discussed from a theoretical view point and compared to experimental results obtained for alumina

A systematic review of portable electronic technology for health education in resource-limited settings.

Science.gov (United States)

McHenry, Megan S; Fischer, Lydia J; Chun, Yeona; Vreeman, Rachel C

2017-08-01

The objective of this study is to conduct a systematic review of the literature of how portable electronic technologies with offline functionality are perceived and used to provide health education in resource-limited settings. Three reviewers evaluated articles and performed a bibliography search to identify studies describing health education delivered by portable electronic device with offline functionality in low- or middle-income countries. Data extracted included: study population; study design and type of analysis; type of technology used; method of use; setting of technology use; impact on caregivers, patients, or overall health outcomes; and reported limitations. Searches yielded 5514 unique titles. Out of 75 critically reviewed full-text articles, 10 met inclusion criteria. Study locations included Botswana, Peru, Kenya, Thailand, Nigeria, India, Ghana, and Tanzania. Topics addressed included: development of healthcare worker training modules, clinical decision support tools, patient education tools, perceptions and usability of portable electronic technology, and comparisons of technologies and/or mobile applications. Studies primarily looked at the assessment of developed educational modules on trainee health knowledge, perceptions and usability of technology, and comparisons of technologies. Overall, studies reported positive results for portable electronic device-based health education, frequently reporting increased provider/patient knowledge, improved patient outcomes in both quality of care and management, increased provider comfort level with technology, and an environment characterized by increased levels of technology-based, informal learning situations. Negative assessments included high investment costs, lack of technical support, and fear of device theft. While the research is limited, portable electronic educational resources present promising avenues to increase access to effective health education in resource-limited settings, contingent

SAGES: a suite of freely-available software tools for electronic disease surveillance in resource-limited settings.

Directory of Open Access Journals (Sweden)

Sheri L Lewis

Full Text Available Public health surveillance is undergoing a revolution driven by advances in the field of information technology. Many countries have experienced vast improvements in the collection, ingestion, analysis, visualization, and dissemination of public health data. Resource-limited countries have lagged behind due to challenges in information technology infrastructure, public health resources, and the costs of proprietary software. The Suite for Automated Global Electronic bioSurveillance (SAGES is a collection of modular, flexible, freely-available software tools for electronic disease surveillance in resource-limited settings. One or more SAGES tools may be used in concert with existing surveillance applications or the SAGES tools may be used en masse for an end-to-end biosurveillance capability. This flexibility allows for the development of an inexpensive, customized, and sustainable disease surveillance system. The ability to rapidly assess anomalous disease activity may lead to more efficient use of limited resources and better compliance with World Health Organization International Health Regulations.

Use and Cost of Electronic Resources in Central Library of Ferdowsi University Based on E-metrics

Directory of Open Access Journals (Sweden)

Mohammad Reza Davarpanah

2012-07-01

Full Text Available The purpose of this study was to investigate the usage of electronic journals in Ferdowsi University, Iran based on e-metrics. The paper also aimed to emphasize the analysis of cost-benefit and the correlation between the journal impact factors and the usage data. In this study experiences of Ferdowsi University library on licensing and usage of electronic resources was evaluated by providing a cost-benefit analysis based on the cost and usage statistics of electronic resources. Vendor-provided data were also compared with local usage data. The usage data were collected by tracking web-based access locally, and by collecting vender-provided usage data. The data sources were one-year of vendor-supplied e-resource usage data such as Ebsco, Elsevier, Proquest, Emerald, Oxford and Springer and local usage data collected from the Ferdowsi university web server. The study found that actual usage values differ for vendor-provided data and local usage data. Elsevier has got the highest usage degree in searches, sessions and downloads. Statistics also showed that a small number of journals satisfy significant amount of use while the majority of journals were used less frequent and some were never used at all. The users preferred the PDF rather than HTML format. The data in subject profile suggested that the provided e-resources were best suited to certain subjects. There was no correlation between IF and electronic journal use. Monitoring the usage of e-resources gained increasing importance for acquisition policy and budget decisions. The article provided information about local metrics for the six surveyed vendors/publishers, e.g. usage trends, requests per package, cost per use as related to the scientific specialty of the university.

Dynamical simulation of structural multiplicity in grain boundaries

International Nuclear Information System (INIS)

Majid, I.; Bristowe, P.D.

1987-06-01

Work on a computer simulation study of a low-energy high-angle boundary structure which is not periodic have been recently reported. This result is of interest since grain boundary structures are usually assumed to have a periodicity corresponding to the appropriate coincidence site lattice (CSL) and many experimental observations of the structure of grain boundaries performed using conventional and high-resolution electron microscopy, electron diffraction and x-ray diffraction appear to support this work. However, this work, using empirical interatomic pair potentials and the relaxation method of molecular statics, have simulated a Σ = 5 36.87 0 (001) twist boundary and found a low energy structure having a larger repeat cell than the CSL and is composed of two different types of structural unit that are randomly distributed in the boundary plane. This result, which has been termed the multiplicity of grain boundary structures, has also been found in the simulation of tilt boundaries. The multiplicity phenomenon is of special interest in twist boundaries since it is used as a structural model to explain the x-ray scattering from a Σ = 5 boundary in gold. These scattering patterns had previously remained unexplained using stable structures that had simple CSL periodicity. Also, the effect of having a multiple number of low energy structural units coexisting in the grain boundary is of more general interest since it implies that the boundary structures may be quasi-periodic and, in some circumstances, may even result in a roughening of the boundary plane. This paper extends this work by showing, using molecular dynamics, that a multiplicity of structural units can actually nucleate spontaneously in a high-angle grain boundary at finite temperatures

A device adaptive inflow boundary condition for Wigner equations of quantum transport

International Nuclear Information System (INIS)

Jiang, Haiyan; Lu, Tiao; Cai, Wei

2014-01-01

In this paper, an improved inflow boundary condition is proposed for Wigner equations in simulating a resonant tunneling diode (RTD), which takes into consideration the band structure of the device. The original Frensley inflow boundary condition prescribes the Wigner distribution function at the device boundary to be the semi-classical Fermi–Dirac distribution for free electrons in the device contacts without considering the effect of the quantum interaction inside the quantum device. The proposed device adaptive inflow boundary condition includes this effect by assigning the Wigner distribution to the value obtained from the Wigner transform of wave functions inside the device at zero external bias voltage, thus including the dominant effect on the electron distribution in the contacts due to the device internal band energy profile. Numerical results on computing the electron density inside the RTD under various incident waves and non-zero bias conditions show much improvement by the new boundary condition over the traditional Frensley inflow boundary condition

Building and Managing Electronic Resources in Digital Era in India with Special Reference to IUCAA and NIV, Pune: A Comparative Case Study

Science.gov (United States)

Sahu, H. K.; Singh, S. N.

2015-04-01

This paper discusses and presents a comparative case study of two libraries in Pune, India, Inter-University Centre for Astronomy and Astrophysics and Information Centre and Library of National Institute of Virology (Indian Council of Medical Research). It compares how both libraries have managed their e-resource collections, including acquisitions, subscriptions, and consortia arrangements, while also developing a collection of their own resources, including pre-prints and publications, video lectures, and other materials in an institutional repository. This study illustrates how difficult it is to manage electronic resources in a developing country like India, even though electronic resources are used more than print resources. Electronic resource management can be daunting, but with a systematic approach, various problems can be solved, and use of the materials will be enhanced.

Grain-boundary unzipping by oxidation in polycrystalline graphene

Science.gov (United States)

Alexandre, Simone; Lucio, Aline; Nunes, Ricardo

2011-03-01

The need for large-scale production of graphene will inevitably lead to synthesis of the polycrystalline material [1,2]. Understanding the chemical, mechanical, and electronic properties of grain boundaries in graphene polycrystals will be crucial for the development of graphene-based electronics. Oxidation of this material has been suggested to lead to graphene ribbons, by the oxygen-driven unzipping mechanism. A cooperative-strain mechanism, based on the formation of epoxy groups along lines of parallel bonds in the hexagons of graphene's honeycomb lattice, was proposed to explain the unzipping effect in bulk graphene In this work we employ ab initio calculations to study the oxidation of polycrystalline graphene by chemisorption of oxygen at the grain boundaries. Our results indicate that oxygen tends to segregate at the boundaries, and that the unzipping mechanism is also operative along the grain boundaries, despite the lack of the parallel bonds due to the presence of fivefold and sevenfold carbon rings along the boundary core. We acknowledge support from the Brazilian agencies: CNPq, Fapemig, and INCT-Materiais de Carbono.

Creating conversation around habitat restoration through boundary work in the St. Louis River, Duluth, MN

Science.gov (United States)

Closing the gaps between scientific research, human well-being and natural resource management requires the use of boundary work to facilitate translation among scientists, resource managers, and the community. Boundary work encompasses the methods, organizations, concepts, and o...

Electron microscopy and auger spectroscopy study of the wetting of the grain boundaries in the systems Mo-Pb, Mo-Sn, Mo-Ni and Ni-Pb

International Nuclear Information System (INIS)

Charai, A.; Kutcherinenko, I.; Priester, L.; Penisson, J.M.; Pontikis, V.; Wolski, K.; Vystavel, T.

2002-01-01

Understanding the mechanism of the intergranular penetration of a liquid phase into a metallic solid is an important problem. The structural and chemical characterization of nano-metric films at grain boundaries is now possible by using high resolution electron microscopy associated with X-ray micro-analysis, electron energy loss spectroscopy and Auger spectroscopy. In order to study this problem, two different classes of model materials were selected according to their crystallographic structure: a bcc metal (molybdenum) and an fcc one (nickel). The wetting element was either lead or tin or nickel. In a first approach, the metallic matrix was polycrystalline. The conditions in which the liquid phase penetrates into the grain boundaries were studied by using special preparation and observation techniques. In particular, the use of a Focused Ion Beam microscope (FIB) allowed the preparation of thin foils located very precisely inside the matrix as well as multi-scale observations. These specimens were further observed in electron microscopy with a very high resolution. (authors)

[Use of internet and electronic resources among Spanish intensivist physicians. First national survey].

Science.gov (United States)

Gómez-Tello, V; Latour-Pérez, J; Añón Elizalde, J M; Palencia-Herrejón, E; Díaz-Alersi, R; De Lucas-García, N

2006-01-01

Estimate knowledge and use habits of different electronic resources in a sample of Spanish intensivists: Internet, E-mail, distribution lists, and use of portable electronic devices. Self-applied questionnaire. A 50-question questionnaire was distributed among Spanish intensivists through the hospital marketing delegates of a pharmaceutical company and of electronic forums. A total of 682 questionnaires were analyzed (participation: 74%). Ninety six percent of those surveyed used Internet individually: 67% admitted training gap. Internet was the second source of clinical consultations most used (61%), slightly behind consultation to colleagues (65%). The pages consulted most were bibliographic databases (65%) and electronic professional journals (63%), with limited use of Evidence Based Medicine pages (19%). Ninety percent of those surveyed used e-mail regularly in the practice of their profession, although 25% admitted that were not aware of its possibilities. The use of E-mail decreased significantly with increase in age. A total of 62% of the intensivists used distribution lists. Of the rest, 42% were not aware of its existence and 32% admitted they had insufficient training to handle them. Twenty percent of those surveyed had portable electronic devices and 64% considered it useful, basically due to its rapid consultation at bedside. Female gender was a negative predictive factor of its use (OR 0.35; 95% CI 0.2-0.63; p=0.0002). A large majority of the Spanish intensivists use Internet and E-mail. E-mail lists and use of portable devices are still underused resources. There are important gaps in training and infrequent use of essential pages. There are specific groups that require directed educational policies.

Model of e-learning with electronic educational resources of new generation

OpenAIRE

A. V. Loban; D. A. Lovtsov

2017-01-01

Purpose of the article: improving of scientific and methodical base of the theory of the е-learning of variability. Methods used: conceptual and logical modeling of the е-learning of variability process with electronic educational resource of new generation and system analysis of the interconnection of the studied subject area, methods, didactics approaches and information and communication technologies means. Results: the formalization complex model of the е-learning of variability with elec...

Diffusion processes in the magnetopause boundary layer

International Nuclear Information System (INIS)

Tsurutani, B.T.; Thorne, R.M.

1982-01-01

Anomalous cross-field diffusion of magnetosheath ions and electrons is a direct consequence of cyclotron-resonant scattering by electrostatic and electromagnetic emissions which are continuously present within the magnetopause boundary layer. Expressions for the rate of cross-field diffusion involving either type of wave are developed and expressed in terms of the absolute upper limit referred to as Bohm diffusion. For the typical average intensity of waves observed in the boundary layer, resonant electron cross-field diffusion is always insignificant. However, magnetosheath ions, resonant with low frequency electrostatic waves, may be transported inward at a rate approaching one tenth the Bohm rate (D/sub perpendiculartsperpendicular/roughly-equal10 3 km 2 /s). While this is not the only mechanism capable of explaining the presence of the low latitude boundary layer it is adequate to account for the typical boundary layer thickness and it should occur at all local times and under all interplanetary conditions. It consequently provides a continuous mechanism for significant mass and momentum transfer across the magnetopause under conditions when field merging is inoperative

Introducing the electronic patient record (EPR) in a hospital setting: boundary work and shifting constructions of professional identities.

Science.gov (United States)

Håland, Erna

2012-06-01

Today's healthcare sector is being transformed by several ongoing processes, among them the introduction of new technologies, new financial models and new ways of organising work. The introduction of the electronic patient record (EPR) is representative and part of these extensive changes. Based on interviews with health personnel and office staff in a regional hospital in Norway, and with health administrators and information technology service-centre staff in the region, the article examines how the introduction of the EPR, as experienced by the participants, affects the work practices and boundaries between various professional groups in the healthcare system and discusses the implications this has for the understanding of medical practice. The article shows how the EPR has become part of the professionals' boundary work; expressing shifting constructions of professional identities. © 2011 The Author. Sociology of Health & Illness © 2011 Foundation for the Sociology of Health & Illness/Blackwell Publishing Ltd.

Study of rapid grain boundary migration in a nanocrystalline Ni thin film

International Nuclear Information System (INIS)

Kacher, Josh; Robertson, I.M.; Nowell, Matt; Knapp, J.; Hattar, Khalid

2011-01-01

Research highlights: → Abnormal growth is distributed randomly in the foil and initiates at different times. → Growth occurs from seemingly uncorrelated regions of the grain boundary. → Growth twins are created during all stages of abnormal grain growth. → Grain growth patterns are qualitatively similar to a vacancy diffusion model. → Grain boundaries and orientations evolve during growth to minimize system energy. - Abstract: Grain boundary migration associated with abnormal grain growth in pulsed-laser deposited Ni was studied in real time by annealing electron transparent films in situ in the transmission electron microscope. The resulting texture evolution and grain boundary types produced were evaluated by ex situ electron backscatter diffraction of interrupted anneals. The combination of these two techniques allowed for the investigation of grain growth rates, grain morphologies, and the evolution of the orientation and grain boundary distributions. Grain boundaries were found to progress in a sporadic, start/stop fashion with no evidence of a characteristic grain growth rate. The orientations of the abnormally growing grains were found to be predominately //ND throughout the annealing process. A high fraction of twin boundaries developed during the annealing process. The intermittent growth from different locations of the grain boundary is discussed in terms of a vacancy diffusion model for grain growth.

Impact of Knowledge Resources Linked to an Electronic Health Record on Frequency of Unnecessary Tests and Treatments

Science.gov (United States)

Goodman, Kenneth; Grad, Roland; Pluye, Pierre; Nowacki, Amy; Hickner, John

2012-01-01

Introduction: Electronic knowledge resources have the potential to rapidly provide answers to clinicians' questions. We sought to determine clinicians' reasons for searching these resources, the rate of finding relevant information, and the perceived clinical impact of the information they retrieved. Methods: We asked general internists, family…

Aleutian Islands Coastal Resources Inventory and Environmental Sensitivity Maps: SOCECON (Socioeconomic Resource Points and Lines)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains human-use resource data for Coastal Resource Service Area (CRSA) boundaries, mineral sites, airports, boat ramps, marinas, and Coast Guard...

Grain boundaries in Ni3Al. 2

International Nuclear Information System (INIS)

Kung, H.; Sass, S.L.

1992-01-01

This paper discusses the dislocation structure of small angle tilt and twist boundaries in ordered Ni 3 Al, with and without boron, investigated using transmission electron microscopy. Dislocation with Burgers vectors that correspond to anti-phase boundary (APB)-coupled superpartials were found in small angle twist boundaries in both boron-free and boron-doped Ni 3 Al, and a small angle tilt boundary in boron-doped Ni 3 Al. The boundary structures are in agreement with theoretical models proposed by Marcinkowski and co-workers. The APB energy determined from the dissociation of the grain boundary dislocations was lower than values reported for isolated APBs in Ni 3 Al. For small angle twist boundaries the presence of boron reduced the APB energy at the interface until it approached zero. This is consistent with the structure of these boundaries containing small regions of increased compositional disorder in the first atomic plane next to the interface

Electronic Document Management: A Human Resource Management Case Study

Directory of Open Access Journals (Sweden)

Thomas Groenewald

2004-11-01

Full Text Available This case study serve as exemplar regarding what can go wrong with the implementation of an electronic document management system. Knowledge agility and knowledge as capital, is outlined against the backdrop of the information society and knowledge economy. The importance of electronic document management and control is sketched thereafter. The literature review is concluded with the impact of human resource management on knowledge agility, which includes references to the learning organisation and complexity theory. The intervention methodology, comprising three phases, follows next. The results of the three phases are presented thereafter. Partial success has been achieved with improving the human efficacy of electronic document management, however the client opted to discontinue the system in use. Opsomming Die gevalle studie dien as voorbeeld van wat kan verkeerd loop met die implementering van ’n elektroniese dokumentbestuur sisteem. Teen die agtergrond van die inligtingsgemeenskap en kennishuishouding word kennissoepelheid en kennis as kapitaal bespreek. Die literatuurstudie word afgesluit met die inpak van menslikehulpbronbestuur op kennissoepelheid, wat ook die verwysings na die leerorganisasie en kompleksietydsteorie insluit. Die metodologie van die intervensie, wat uit drie fases bestaan, volg daarna. Die resultate van die drie fases word vervolgens aangebied. Slegs gedeelte welslae is behaal met die verbetering van die menslike doeltreffendheid ten opsigte van elektroniese dokumentbestuur. Die klient besluit egter om nie voort te gaan om die huidige sisteem te gebruik nie.

International Boundary United States Mexico Minute 315

Data.gov (United States)

International Boundary & Water Commission — This dataset was created to provide resource managers, public officials, researchers, and the general public with ready access to the location of the international...

The boundary-scan handbook

CERN Document Server

Parker, Kenneth P

2016-01-01

Aimed at electronics industry professionals, this 4th edition of the Boundary Scan Handbook describes recent changes to the IEEE1149.1 Standard Test Access Port and Boundary-Scan Architecture. This updated edition features new chapters on the possible effects of the changes on the work of the practicing test engineers and the new 1149.8.1 standard. Anyone needing to understand the basics of boundary scan and its practical industrial implementation will need this book. Provides an overview of the recent changes to the 1149.1 standard and the effect of the changes on the work of test engineers;   Explains the new IEEE 1149.8.1 subsidiary standard and applications;   Describes the latest updates on the supplementary IEEE testing standards. In particular, addresses: IEEE Std 1149.1                      Digital Boundary-Scan IEEE Std 1149.4                      Analog Boundary-Scan IEEE Std 1149.6                      Advanced I/O Testing IEEE Std 1149.8.1           �...

Tokamak plasma boundary layer model

International Nuclear Information System (INIS)

Volkov, T.F.; Kirillov, V.D.

1983-01-01

A model has been developed for the limiter layer and for the boundary region of the plasma column in a tokamak to facilitate analytic calculations of the thickness of the limiter layers, the profiles and boundary values of the temperature and the density under various conditions, and the difference between the electron and ion temperatures. This model can also be used to analyze the recycling of neutrals, the energy and particle losses to the wall and the limiter, and other characteristics

Easy boundary definition for EGUN

International Nuclear Information System (INIS)

Becker, R.

1989-01-01

The relativistic electron optics program EGUN has reached a broad distribution, and many users have asked for an easier way of boundary input. A preprocessor to EGUN has been developed that accepts polygonal input of boundary points, and offers features such as rounding off of corners, shifting and squeezing of electrodes and simple input of slanted Neumann boundaries. This preprocessor can either be used on a PC that is linked to a mainframe using the FORTRAN version of EGUN, or in connection with the version EGNc, which also runs on a PC. In any case, direct graphic response on the PC greatly facilitates the creation of correct input files for EGUN. (orig.)

Easy boundary definition for EGUN

Science.gov (United States)

Becker, R.

1989-06-01

The relativistic electron optics program EGUN [1] has reached a broad distribution, and many users have asked for an easier way of boundary input. A preprocessor to EGUN has been developed that accepts polygonal input of boundary points, and offers features such as rounding off of corners, shifting and squeezing of electrodes and simple input of slanted Neumann boundaries. This preprocessor can either be used on a PC that is linked to a mainframe using the FORTRAN version of EGUN, or in connection with the version EGNc, which also runs on a PC. In any case, direct graphic response on the PC greatly facilitates the creation of correct input files for EGUN.

Easy boundary definition for EGUN

Energy Technology Data Exchange (ETDEWEB)

Becker, R. (Frankfurt Univ. (Germany, F.R.). Inst. fuer Angewandte Physik)

1989-06-01

The relativistic electron optics program EGUN has reached a broad distribution, and many users have asked for an easier way of boundary input. A preprocessor to EGUN has been developed that accepts polygonal input of boundary points, and offers features such as rounding off of corners, shifting and squeezing of electrodes and simple input of slanted Neumann boundaries. This preprocessor can either be used on a PC that is linked to a mainframe using the FORTRAN version of EGUN, or in connection with the version EGNc, which also runs on a PC. In any case, direct graphic response on the PC greatly facilitates the creation of correct input files for EGUN. (orig.).

The influence of grain boundary structure on diffusional creep

DEFF Research Database (Denmark)

Thorsen, Peter Anker; Bilde-Sørensen, Jørgen

1999-01-01

the deformation caused by deposition of material at (or removal of material from) grain boundaries. The misorientation across the grain boundaries, and hence the character of the boundaries, was measured with the use of electron back-scattering patterns. The deformation behavior of the individual boundaries......A Cu-2wt%Ni-alloy was deformed in tension in the diffusional creep regime (Nabarro-Herring creep). A periodic grid consisting of alumina was deposited on the surface of the creep specimen prior to creep. This makes it possible to separate the deformation caused by grain boundary sliding from...

Challenges in the implementation of an electronic surveillance system in a resource-limited setting: Alerta, in Peru

Directory of Open Access Journals (Sweden)

Soto Giselle

2008-11-01

Full Text Available Abstract Background Infectious disease surveillance is a primary public health function in resource-limited settings. In 2003, an electronic disease surveillance system (Alerta was established in the Peruvian Navy with support from the U.S. Naval Medical Research Center Detachment (NMRCD. Many challenges arose during the implementation process, and a variety of solutions were applied. The purpose of this paper is to identify and discuss these issues. Methods This is a retrospective description of the Alerta implementation. After a thoughtful evaluation according to the Centers for Disease Control and Prevention (CDC guidelines, the main challenges to implementation were identified and solutions were devised in the context of a resource-limited setting, Peru. Results After four years of operation, we have identified a number of challenges in implementing and operating this electronic disease surveillance system. These can be divided into the following categories: (1 issues with personnel and stakeholders; (2 issues with resources in a developing setting; (3 issues with processes involved in the collection of data and operation of the system; and (4 issues with organization at the central hub. Some of the challenges are unique to resource-limited settings, but many are applicable for any surveillance system. For each of these challenges, we developed feasible solutions that are discussed. Conclusion There are many challenges to overcome when implementing an electronic disease surveillance system, not only related to technology issues. A comprehensive approach is required for success, including: technical support, personnel management, effective training, and cultural sensitivity in order to assure the effective deployment of an electronic disease surveillance system.

Creating conversation around habitat restoration through boundary work in the St. Louis River, Duluth, MN (presentation)

Science.gov (United States)

Closing the gaps between scientific research, human well-being and natural resource management requires the use of boundary work to facilitate translation among scientists, resource managers, and the community. Boundary work encompasses the methods, organizations, concepts, and o...

The effect of grain boundary chemistry on the slip transmission process through grain boundaries in Ni3Al

International Nuclear Information System (INIS)

Robertson, I.M.; Lee, T.C.; Subramanian, R.; Birnbaum, H.K.

1992-01-01

This paper reports on the conditions established in disordered FCC systems for predicting the slip system that will be activated by a grain boundary to relieve a local stress concentration that have been applied to the ordered FCC alloy Ni 3 Al. The slip transfer behavior in hypo-stoichiometric Ni 3 Al with (0.2 at. %B) and without boron was directly observed by performing the deformation experiments in situ in the transmission electron microscope. In the boron-free and boron-doped alloys, lattice dislocations were incorporated in the grain boundary, but did not show evidence of dissociation to grain boundary dislocations or of movement in the grain boundary plane. The stress concentration associated with the dislocation pileup at the grain boundary are relieved by the emission of dislocations from the grain boundary in the boron-doped alloy. The slip system initiated in the adjoining grain obeyed the conditions established for disordered FCC systems. In the boron-free alloy, the primary stress relief mechanism was grain-boundary cracking, although dislocation emission from the grain boundary also occurred and accompanied intergranular crack advance

Generalized boundary conditions in an existence and uniqueness proof for the solution of the non-stationary electron Boltzmann equation by means of operator-semigroups

International Nuclear Information System (INIS)

Bartolomaeus, G.; Wilhelm, J.

1983-01-01

Recently, based on the semigroup approach a new proof was presented of the existence of a unique solution of the non-stationary Boltzmann equation for the electron component of a collision dominated plasma. The proof underlies some restriction which should be overcome to extend the validity range to other problems of physical interest. One of the restrictions is the boundary condition applied. The choice of the boundary condition is essential for the proof because it determines the range of definition of the infinitesimal generator and thus the operator semigroup itself. The paper proves the existence of a unique solution for generalized boundary conditions, this solution takes non-negative values, which is necessary for a distribution function from the physical point of view. (author)

Discussion and analytical test for inclusion of advanced field and boundary condition in theory of free electron lasers

Science.gov (United States)

Niknejadi, Pardis; Madey, John M. J.

2017-09-01

By the covariant statement of the distance in space-time separating transmitter and receivers, the emission and absorption of the retarded and advanced waves are all simultaneous. In other words, for signals carried on electromagnetic waves (advanced or retarded) the invariant interval (cdt) 2 -dr2 between the emission of a wave and it's absorption at the non-reflecting boundary is always identically zero. Utilizing this principle, we have previously explained the advantages of including the coherent radiation reaction force as a part of the solution to the boundary value problem for FELs that radiate into "free space" (Self Amplified Spontaneous Emission (SASE) FELs) and discussed how the advanced field of the absorber can interact with the radiating particles at the time of emission. Here we present an analytical test which verifies that a multilayer mirror can act as a band pass filter and can contribute to microbunching in the electron beam. Here we will discuss motivation, conditions and requirements, and method for testing this effect.

State Wildlife Management Area Boundaries - Publicly Accessible

Data.gov (United States)

Minnesota Department of Natural Resources — This polygon theme contains boundaries for approximately 1392 Wildlife Management Areas (WMAs) across the state covering nearly 1,288,000 acres. WMAs are part of the...

Observing grain boundaries in CVD-grown monolayer transition metal dichalcogenides

KAUST Repository

Ly, Thuchue

2014-11-25

Two-dimensional monolayer transition metal dichalcogenides (TMdCs), driven by graphene science, revisit optical and electronic properties, which are markedly different from bulk characteristics. These properties are easily modified due to accessibility of all the atoms viable to ambient gases, and therefore, there is no guarantee that impurities and defects such as vacancies, grain boundaries, and wrinkles behave as those of ideal bulk. On the other hand, this could be advantageous in engineering such defects. Here, we report a method of observing grain boundary distribution of monolayer TMdCs by a selective oxidation. This was implemented by exposing directly the TMdC layer grown on sapphire without transfer to ultraviolet light irradiation under moisture-rich conditions. The generated oxygen and hydroxyl radicals selectively functionalized defective grain boundaries in TMdCs to provoke morphological changes at the boundary, where the grain boundary distribution was observed by atomic force microscopy and scanning electron microscopy. This paves the way toward the investigation of transport properties engineered by defects and grain boundaries. (Figure Presented).

Considering Point-of-Care Electronic Medical Resources in Lieu of Traditional Textbooks for Medical Education.

Science.gov (United States)

Hale, LaDonna S; Wallace, Michelle M; Adams, Courtney R; Kaufman, Michelle L; Snyder, Courtney L

2015-09-01

Selecting resources to support didactic courses is a critical decision, and the advantages and disadvantages must be carefully considered. During clinical rotations, students not only need to possess strong background knowledge but also are expected to be proficient with the same evidence-based POC resources used by clinicians. Students place high value on “real world” learning and therefore may place more value on POC resources that they know practicing clinicians use as compared with medical textbooks. The condensed nature of PA education requires students to develop background knowledge and information literacy skills over a short period. One way to build that knowledge and those skills simultaneously is to use POC resources in lieu of traditional medical textbooks during didactic training. Electronic POC resources offer several advantages over traditional textbooks and should be considered as viable options in PA education.

Engineering Mixed Ionic Electronic Conduction in La 0.8 Sr 0.2 MnO 3+ δ Nanostructures through Fast Grain Boundary Oxygen Diffusivity

KAUST Repository

Saranya, Aruppukottai M.

2015-04-09

© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim. Nanoionics has become an increasingly promising field for the future development of advanced energy conversion and storage devices, such as batteries, fuel cells, and supercapacitors. Particularly, nanostructured materials offer unique properties or combinations of properties as electrodes and electrolytes in a range of energy devices. However, the enhancement of the mass transport properties at the nanoscale has often been found to be difficult to implement in nanostructures. Here, an artificial mixed ionic electronic conducting oxide is fabricated by grain boundary (GB) engineering thin films of La0.8Sr0.2MnO3+δ. This electronic conductor is converted into a good mixed ionic electronic conductor by synthesizing a nanostructure with high density of vertically aligned GBs with high concentration of strain-induced defects. Since this type of GBs present a remarkable enhancement of their oxide-ion mass transport properties (of up to six orders of magnitude at 773 K), it is possible to tailor the electrical nature of the whole material by nanoengineering, especially at low temperatures. The presented results lead to fundamental insights into oxygen diffusion along GBs and to the application of these engineered nanomaterials in new advanced solid state ionics devices such are micro-solid oxide fuel cells or resistive switching memories. An electronic conductor such as La0.8Sr0.2MnO3+δ is converted into a good mixed ionic electronic conductor by synthesizing a nanostructure with excellent electronic and oxygen mass transport properties. Oxygen diffusion highways are created by promoting a high concentration of strain-induced defects in the grain boundary region. This novel strategy opens the way for synthesizing new families of artificial mixed ionic-electronic conductors by design.

Electronic and elemental properties of the Cu2ZnSn(S,Se)4 surface and grain boundaries

International Nuclear Information System (INIS)

Haight, Richard; Shao, Xiaoyan; Wang, Wei; Mitzi, David B.

2014-01-01

X-ray and femtosecond UV photoelectron spectroscopy, secondary ion mass spectrometry and photoluminescence imaging were used to investigate the electronic and elemental properties of the CZTS,Se surface and its oxides. Oxide removal reveals a very Cu poor and Zn rich surface relative to bulk composition. O and Na are observed at the surface and throughout the bulk. Upward bending of the valence bands indicates the presence of negative charge in the surface region and the Fermi level is found near the band gap center. The presence of point defects and the impact of these findings on grain boundary properties will be described

Electronic and elemental properties of the Cu2ZnSn(S,Se)4 surface and grain boundaries

Science.gov (United States)

Haight, Richard; Shao, Xiaoyan; Wang, Wei; Mitzi, David B.

2014-01-01

X-ray and femtosecond UV photoelectron spectroscopy, secondary ion mass spectrometry and photoluminescence imaging were used to investigate the electronic and elemental properties of the CZTS,Se surface and its oxides. Oxide removal reveals a very Cu poor and Zn rich surface relative to bulk composition. O and Na are observed at the surface and throughout the bulk. Upward bending of the valence bands indicates the presence of negative charge in the surface region and the Fermi level is found near the band gap center. The presence of point defects and the impact of these findings on grain boundary properties will be described.

Resource conservation approached with an appropriate collection and upgrade-remanufacturing for used electronic products.

Science.gov (United States)

Zlamparet, Gabriel I; Tan, Quanyin; Stevels, A B; Li, Jinhui

2018-03-01

This comparative research represents an example for a better conservation of resources by reducing the amount of waste (kg) and providing it more value under the umbrella of remanufacturing. The three discussed cases will expose three issues already addressed separately in the literature. The generation of waste electrical and electronic equipment (WEEE) interacts with the environmental depletion. In this article, we gave the examples of addressed issues under the concept of remanufacturing. Online collection opportunity eliminating classical collection, a business to business (B2B) implementation for remanufactured servers and medical devices. The material reuse (recycling), component sustainability, reuse (part harvesting), product reuse (after repair/remanufacturing) indicates the recovery potential using remanufacturing tool for a better conservation of resources adding more value to the products. Our findings can provide an overview of new system organization for the general collection, market potential and the technological advantages using remanufacturing instead of recycling of WEEE or used electrical and electronic equipment. Copyright © 2017. Published by Elsevier Ltd.

Coherent Electron Focussing in a Two-Dimensional Electron Gas.

NARCIS (Netherlands)

Houten, H. van; Wees, B.J. van; Mooij, J.E.; Beenakker, C.W.J.; Williamson, J.G.; Foxon, C.T.

1988-01-01

The first experimental realization of ballistic point contacts in a two-dimensional electron gas for the study of transverse electron focussing by a magnetic field is reported. Multiple peaks associated with skipping orbits of electrons reflected specularly by the channel boundary are observed. At

Grain boundary structures in La2/3Ca1/3MnO3 thin films

International Nuclear Information System (INIS)

Miller, D. J.; Lin, Y.-K.; Vlasko-Vlasov, V.; Welp, U.

1999-01-01

As with many other oxide-based compounds that exhibit electronic behavior, structural defects have a strong influence on the electronic properties of the CMR manganites. In this work, the authors have studied the effect of grain boundaries on the transport properties and on the local orientation of magnetization. Thin films of the perovskite-related La 2/3 Ca 1/3 MnO 3 compound were deposited onto bicrystal substrates using pulsed laser deposition. Transport measurements showed some enhancement of magnetoresistance across the grain boundary. The structure of the boundary was evaluated by electron microscopy. In contrast with the highly meandering boundaries typically observed in bicrystals of high temperature superconductors, the boundaries in these films are relatively straight and well defined. However, magneto-optical imaging showed that the local magnetization was oriented out of the plane at the grain boundary while it was oriented within the plane in the grains on either side. This coordinated reorientation of local magnetization near the grain boundary leads to enhanced magnetoresistance across the boundary in low fields

Effects of the Use of Electronic Human Resource Management (EHRM Within Human Resource Management (HRM Functions at Universities

Directory of Open Access Journals (Sweden)

Chux Gervase Iwu

2016-09-01

Full Text Available This study set out to examine the effect of e-hrm systems in assisting human resource practitioners to execute their duties and responsibilities. In comparison to developed economies of the world, information technology adoption in sub-Saharan Africa has not been without certain glitches. Some of the factors that are responsible for these include poor need identification, sustainable funding, and insufficient skills. Besides these factors, there is also the issue of change management and users sticking to what they already know. Although, the above factors seem negative, there is strong evidence that information systems such as electronic human resource management present benefits to an organization. To achieve this, a dual research approach was utilized. Literature assisted immensely in both the development of the conceptual framework upon which the study hinged as well as in the development of the questionnaire items. The study also made use of an interview checklist to guide the participants. The findings reveal a mix of responses that indicate that while there are gains in adopting e-hrm systems, it is wiser to consider supporting resources as well as articulate the needs of the university better before any investment is made.

Electronic human resource management: Enhancing or entrancing?

Directory of Open Access Journals (Sweden)

Paul Poisat

2017-07-01

Full Text Available Orientation: This article provides an investigation into the current level of development of the body of knowledge related to electronic human resource management (e-HRM by means of a qualitative content analysis. Several aspects of e-HRM, namely definitions of e-HRM, the theoretical perspectives around e-HRM, the role of e-HRM, the various types of e-HRM and the requirements for successful e-HRM, are examined. Research purpose: The purpose of the article was to determine the status of e-HRM and examine the studies that report on the link between e-HRM and organisational productivity. Motivation for the study: e-HRM has the capacity to improve organisational efficiency and leverage the role of human resources (HR as a strategic business partner. Main findings: The notion that the implementation of e-HRM will lead to improved organisational productivity is commonly assumed; however, empirical evidence in this regard was found to be limited. Practical/managerial implications: From the results of this investigation it is evident that more research is required to gain a greater understanding of the influence of e-HRM on organisational productivity, as well as to develop measures for assessing this influence. Contribution: This article proposes additional areas to research and measure when investigating the effectiveness of e-HRM. It provides a different lens from which to view e-HRM assessment whilst keeping it within recognised HR measurement parameters (the HR value chain. In addition, it not only provides areas for measuring e-HRM’s influence but also provides important clues as to how the measurements may be approached.

Complementary AES and AEM of grain boundary regions in irradiated γ'-strengthened alloys

International Nuclear Information System (INIS)

Farrell, K.; Kishimoto, N.; Clausing, R.E.; Heatherly, L.; Lehman, G.L.

1986-01-01

Two microchemical analysis techniques are used to measure solute segregation at grain boundaries in two γ'-strengthened, fcc Fe-Ni-Cr alloys that display radiation-induced intergranular fracture. Scanning Auger electron spectroscopy (AES) of grain boundary fracture surfaces and analytical electron microscopy (AEM) of intact grain boundaries using energy-dispersive x-ray spectroscopy show good agreement on the nature and extent of segregation. The elements Ni, Si, Ti, and Mo are found to accumulate in G, Laves and γ' phases on the grain boundaries. Segregation of P is detected by AES. The complementary features of the two analytical techniques are discussed briefly

Identifying and evaluating electronic learning resources for use in adult-gerontology nurse practitioner education.

Science.gov (United States)

Thompson, Hilaire J; Belza, Basia; Baker, Margaret; Christianson, Phyllis; Doorenbos, Ardith; Nguyen, Huong

2014-01-01

Enhancing existing curricula to meet newly published adult-gerontology advanced practice registered nurse (APRN) competencies in an efficient manner presents a challenge to nurse educators. Incorporating shared, published electronic learning resources (ELRs) in existing or new courses may be appropriate in order to assist students in achieving competencies. The purposes of this project were to (a) identify relevant available ELR for use in enhancing geriatric APRN education and (b) to evaluate the educational utility of identified ELRs based on established criteria. A multilevel search strategy was used. Two independent team members reviewed identified ELR against established criteria to ensure utility. Only resources meeting all criteria were retained. Resources were found for each of the competency areas and included formats such as podcasts, Web casts, case studies, and teaching videos. In many cases, resources were identified using supplemental strategies and not through traditional search or search of existing geriatric repositories. Resources identified have been useful to advanced practice educators in improving lecture and seminar content in a particular topic area and providing students and preceptors with additional self-learning resources. Addressing sustainability within geriatric APRN education is critical for sharing of best practices among educators and for sustainability of teaching and related resources. © 2014.

Systematic review of electronic surveillance of infectious diseases with emphasis on antimicrobial resistance surveillance in resource-limited settings.

Science.gov (United States)

Rattanaumpawan, Pinyo; Boonyasiri, Adhiratha; Vong, Sirenda; Thamlikitkul, Visanu

2018-02-01

Electronic surveillance of infectious diseases involves rapidly collecting, collating, and analyzing vast amounts of data from interrelated multiple databases. Although many developed countries have invested in electronic surveillance for infectious diseases, the system still presents a challenge for resource-limited health care settings. We conducted a systematic review by performing a comprehensive literature search on MEDLINE (January 2000-December 2015) to identify studies relevant to electronic surveillance of infectious diseases. Study characteristics and results were extracted and systematically reviewed by 3 infectious disease physicians. A total of 110 studies were included. Most surveillance systems were developed and implemented in high-income countries; less than one-quarter were conducted in low-or middle-income countries. Information technologies can be used to facilitate the process of obtaining laboratory, clinical, and pharmacologic data for the surveillance of infectious diseases, including antimicrobial resistance (AMR) infections. These novel systems require greater resources; however, we found that using electronic surveillance systems could result in shorter times to detect targeted infectious diseases and improvement of data collection. This study highlights a lack of resources in areas where an effective, rapid surveillance system is most needed. The availability of information technology for the electronic surveillance of infectious diseases, including AMR infections, will facilitate the prevention and containment of such emerging infectious diseases. Copyright © 2018 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

The INTERBALL-Tail ELECTRON experiment: initial results on the low-latitude boundary layer of the dawn magnetosphere

Directory of Open Access Journals (Sweden)

J.-A. Sauvaud

Full Text Available The Toulouse electron spectrometer flown on the Russian project INTERBALL-Tail performs electron measurements from 10 to 26 000 eV over a 4 solid angle in a satellite rotation period. The INTERBALL-Tail probe was launched on 3 August 1995 together with a subsatellite into a 65° inclination orbit with an apogee of about 30 R_E. The INTERBALL mission also includes a polar spacecraft launched in August 1996 for correlated studies of the outer magnetosphere and of the auroral regions. We present new observations concerning the low-latitude boundary layers (LLBL of the magnetosphere obtained near the dawn magnetic meridian. LLBL are encountered at the interface between two plasma regimes, the magnetosheath and the dayside extension of the plasma sheet. Unexpectedly, the radial extent of the region where LLBL electrons can be sporadically detected as plasma clouds can reach up to 5 R_E inside the magnetopause. The LLBL core electrons have an average energy of the order of 100 eV and are systematically field-aligned and counterstreaming. As a trend, the temperature of the LLBL electrons increases with decreasing distance to Earth. Along the satellite orbit, the apparent time of occurrence of LLBL electrons can vary from about 5 to 20 min from one pass to another. An initial first comparison between electron- and magnetic-field measurements indicates that the LLBL clouds coincide with a strong increase in the magnetic field (by up to a factor of 2. The resulting strong magnetic field gradient can explain why the plasma-sheet electron flux in the keV range is strongly depressed in LLBL occurrence regions (up to a factor of sim10. We also show that LLBL electron encounters are related to field-aligned current structures and that wide LLBL correspond to northward interplanetary magnetic field. Evidence for LLBL/plasma-sheet electron leakage into the magnetosheath during southward IMF is also presented.

Process-based investigation of cross-boundary environmental pressure from urban household consumption

International Nuclear Information System (INIS)

Yang, Dewei; Lin, Yanjie; Gao, Lijie; Sun, Yanwei; Wang, Run; Zhang, Guoqin

2013-01-01

Sustainability research at the city scale is increasingly focusing on urban household consumption in the context of global climate change. We use a complementary emergy accounting (EMA) and carbon footprint accounting (CFA) method to investigate the environmental pressure generated by household consumption in Xiamen, China. We distinguish between the resource extraction, consumption and disposal stages within an urban spatial conceptual framework, comprising the Urban Footprint Region (UFR) and Urban Sprawl Region (USR), and analyze five environmental footprint categories associated with cross-boundary household emergy and carbon flows. Cross-boundary activities, which link the USR with its UFR, contributed nearly 90% of total emergy and 70% of total GHG emissions in CFA. Transport fuel, building materials and food contribute most to environmental pressure in both EMA and CFA. The results indicate a significant cross-boundary resource burden and environmental footprint associated with household activities. The employed framework, method, and scope challenge the conventional spatial boundary of the urban system, and the results have important policy implications for urban sustainability and cross-boundary environmental management. - Highlights: ► We propose an urban spatial conceptual framework that includes USR and UFRs. ► A complementary EMA and CFA method is employed in urban household consumption system. ► Process-based cross-boundary environmental pressure of household consumption are evaluated. ► USR exerts pressure on its UFRs by extensive resource extraction and environmental emissions. ► We elucidate the USR–UFR environmental relationships and household energy policy

From Millennium ERM to Proquest 360 Resource Manager: Implementing a new Electronic Resources Management System ERMS in an International Graduate Research University in Saudi Arabia

KAUST Repository

Ramli, Rindra M.

2017-01-01

An overview of the Recommendation Study and the subsequent Implementation of a new Electronic Resources Management system ERMS in an international graduate research university in the Kingdom of Saudi Arabia. It covers the timeline, deliverables

Simulation of the electron acoustic instability for a finite-size electron beam system

International Nuclear Information System (INIS)

Lin, C.S.; Winske, D.

1987-01-01

Satellite observations at midlatitudes (≅20,000 km) near the earth's dayside polar cusp boundary layer indicate that the upward electron beams have a narrow latitudinal width up to 0.1 0 . In the cusp boundary layer where the electron population consists of a finite-size electron beam in a background of uniform cold and hot electrons, the electron acoustic mode is unstable inside the electron beam but damped outside the electron beam. Simulations of the electron acoustic instability for a finite-size beam system are carried out with a particle-in-cell code to investigate the heating phenomena associated with the instability and the width of the heating region. The simulations show that the finite-size electron beam radiates electrostatic electron acoustic waves. The decay length of the electron acoustic waves outside the beam in the simulation agrees with the spatial decay length derived from the linear dispersion equation

Numerical study of the atomic and electronic structure of some silicon grain boundaries

International Nuclear Information System (INIS)

Torrent, M.

1996-01-01

This work contributes to the theoretical study of extended defects in covalent materials. The study is especially devoted to the tilt grain boundaries in silicon as a model material. The theoretical model is based on the self-consistent tight-binding approximation and is applied within two numerical techniques: the fast 'order N' density-matrix method and the diagonalization technique which allows the sampling of the reciprocal space. Total energy parameters of the model have been fitted in order to reproduce the silicon band structure (with a correct gap value) and the transferability of crystalline and mechanical properties of this material. A new type of boundary conditions is proposed and tested. These conditions, named 'ante-periodic' or 'Moebius', allow only one grain boundary per box instead of two and decrease the CPU time by a factor of two. The model is then applied to the study of the Σ=25 [001] (710) grain boundary. The results show the possible presence in this boundary of low energy non-reconstructed atomic structures which are electrically active. This confirms what had been suggested by some experimental observations. The same study is also performed for the Σ=13 [001] (510) grain boundary. In order to compare the intrinsic electrical activity in the previous grain boundaries with the one induced by impurities, a total energy parametrization for the silicon-nickel bond is achieved and used in preliminary calculations. Finally the two variants of the Σ=11 [011] (2-33) interface are studied, especially their respective interfacial energies. The result disagrees with previous calculations using phenomenological potentials. (author)

Effect of crystal orientation on grain boundary migration and radiation-induced segregation

International Nuclear Information System (INIS)

Hashimoto, N.; Eda, Y.; Takahashi, H.

1996-01-01

Fe-Cr-Ni, Ni-Al and Ni-Si alloys were electron-irradiated using a high voltage electron microscope (1 MeV), and in situ observations of the structural evolution and micro-chemical analysis were carried out. During the irradiation, the grain boundaries in the irradiated region migrated, while no grain boundary migration occurred in the unirradiated area. The occurrence of boundary migration depended on the orientation relationship of the boundary interfaces. Grain boundary migration took place in Fe-Cr-Ni and Ni-Si alloys with large crystal orientation difference between the two grains across a grain boundary. In Ni-Al, however, the grain boundary migration did not occur. The solute segregation was caused at grain boundary under irradiation and this segregation behavior was closely related to solute size, namely the concentrations of undersized Ni and oversized Cr elements in Fe-Cr-Ni alloy increased and reduced at grain boundary, respectively. The same dependence of segregation on the solute size was derived in Ni-Si and Ni-Al alloys, in which Si and Al solutes are undersized and oversized elements, respectively. Therefore, Si solute enriched and Al solute depleted at grain boundary. From the present segregation behavior, it is suggested that the flow of point defects into the boundary is the cause of grain boundary migration. (orig.)

Changes in grain boundary composition induced by neutron irradiation of austenitic stainless steels

International Nuclear Information System (INIS)

Asano, K.; Nakata, K.; Fukuya, K.; Kodama, M.

1992-01-01

The radiation induced segregation of solutes to the grain boundary in austenitic stainless steels were studied. Type 304 and type 316 steel samples neutron irradiated at 561K up to 9.2x10 25 n/m 2 were obtained and minute compositional profiles across grain boundaries were examined using an analytical scanning transmission electron microscope equipped with a field emission electron gun. Chromium was slightly enriched at grain boundaries at the lowest irradiation dose but decreased with increasing fluence. Higher fluence irradiation resulted in depletion in chromium and molybdenum, and enrichment in nickel, silicon and phosphorus. These changes in grain boundary chemistry were limited within about 5nm of the boundary. Significant depletion of chromium and enrichment of impurities on the grain boundary occurred at fluences roughly coincidental with that of SCC susceptibility change obtained from another project

Characteristics of the magnetospheric boundary layer and magnetopause layer as observed by Imp 6

International Nuclear Information System (INIS)

Eastman, T.E.; Hones, E.W. Jr.

1979-01-01

Imp 6 observations of the low-latitude magnetospheric boundary layer indicate that the plasma within it is supplied primarily by direct entry of magnetosheath plasma across the magnetopause layer. We define the magnetopause layer as the current layer (separating the magnetosheath from the boundary layer) through which the magnetic field shifts in direction. High temporal resolution (3-s average) data reveal that in a majority of Imp 6 magnetopause crossing, no distinct changes in electron density or energry spectra are observed at the magne opause layer. In all Imp 6 crossings, some magnetosheathlike plasma is observed earthward of the magnetopause layer, implying the existence of a boundary layer. Boundary layer electron energy spectra are often virtually indistinguishable from the adjacent magnetosheath spectra. Low-latitude boundary layer bulk plasma flow as observed by Imp 6 almost always has an antisunward component and often has a significant cross-field component. The boundary layer thickness is highly variable and is generally much larger than the magnetopause layer thickness. Energetic electron pitch angle distributions indicate that the low-latitude boundary layers is normally on closed field lines. We conclude that diffusive as well as nondiffusive processes probably contribute to the entry of magnetosheath plasma into the boundary layer

Polarity of translation boundaries in antiferroelectric PbZrO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Wei, Xian-Kui, E-mail: xiankui.wei@epfl.ch [Ceramics Laboratory, EPFL–Swiss Federal Institute of Technology, Lausanne 1015 (Switzerland); Peter Grünberg Institute and Ernst Ruska Center for Microscopy and Spectroscopy with Electrons, Research Center Jülich, 52425 Jülich (Germany); Jia, Chun-Lin [Peter Grünberg Institute and Ernst Ruska Center for Microscopy and Spectroscopy with Electrons, Research Center Jülich, 52425 Jülich (Germany); International Centre of Dielectric Research, The School of Electronic and Information Engineering, Xi’an Jiaotong University, Xi’an 710049 (China); Roleder, Krystian [Institute of Physics, University of Silesia, Katowice 40007 (Poland); Setter, Nava [Ceramics Laboratory, EPFL–Swiss Federal Institute of Technology, Lausanne 1015 (Switzerland)

2015-02-15

Graphical abstract: Strain-free rigid model and aberration-corrected transmission electron microscopes are used to investigate the polarity of translation boundaries in antiferroelectric PbZrO{sub 3}. - Highlights: • Domain boundaries in antiferroelectric PbZrO{sub 3} show polar and antipolar property. • The antiphase boundary can split into “sub-domains”. • Polarization reversal possibly exists inside the translation boundaries. • Thermal treatment can alter morphology and density of the translation boundaries. - Abstract: The polarity of translation boundaries (TBs) in antiferroelectric PbZrO{sub 3} is investigated. We show that previous experimentally reported polar property of R{sub III-1} type TB can be well approximated by a strain-free rigid model. Based on this, the modeling investigation suggests that there are two additional polar TBs, three antipolar-like TBs and one antipolar antiphase boundary. High-resolution scanning-transmission-electron-microscopy study reveals that the straight R{sub III-1} type TB can split into “sub-domains” with possible polarization reversal, suggesting the occurrence of ferroic orders at the TBs. In addition, dependence of morphology and density of the TBs on thermal treatments is discussed according to our results.

Open-Source Electronic Health Record Systems for Low-Resource Settings: Systematic Review.

Science.gov (United States)

Syzdykova, Assel; Malta, André; Zolfo, Maria; Diro, Ermias; Oliveira, José Luis

2017-11-13

Despite the great impact of information and communication technologies on clinical practice and on the quality of health services, this trend has been almost exclusive to developed countries, whereas countries with poor resources suffer from many economic and social issues that have hindered the real benefits of electronic health (eHealth) tools. As a component of eHealth systems, electronic health records (EHRs) play a fundamental role in patient management and effective medical care services. Thus, the adoption of EHRs in regions with a lack of infrastructure, untrained staff, and ill-equipped health care providers is an important task. However, the main barrier to adopting EHR software in low- and middle-income countries is the cost of its purchase and maintenance, which highlights the open-source approach as a good solution for these underserved areas. The aim of this study was to conduct a systematic review of open-source EHR systems based on the requirements and limitations of low-resource settings. First, we reviewed existing literature on the comparison of available open-source solutions. In close collaboration with the University of Gondar Hospital, Ethiopia, we identified common limitations in poor resource environments and also the main requirements that EHRs should support. Then, we extensively evaluated the current open-source EHR solutions, discussing their strengths and weaknesses, and their appropriateness to fulfill a predefined set of features relevant for low-resource settings. The evaluation methodology allowed assessment of several key aspects of available solutions that are as follows: (1) integrated applications, (2) configurable reports, (3) custom reports, (4) custom forms, (5) interoperability, (6) coding systems, (7) authentication methods, (8) patient portal, (9) access control model, (10) cryptographic features, (11) flexible data model, (12) offline support, (13) native client, (14) Web client,(15) other clients, (16) code

AES/STEM grain boundary analysis of stabilized zirconia ceramics

NARCIS (Netherlands)

Winnubst, Aloysius J.A.; Kroot, P.J.M.; Burggraaf, A.J.

1983-01-01

Semiquantitative Auger Electron Spectroscopy (AES) on pure monophasic (ZrO2)0.83(YO1.5)0.17 was used to determine the chemical composition of the grain boundaries. Grain boundary enrichment with Y was observed with an enrichment factor of about 1.5. The difference in activation energy of the ionic

Management accounting as the inter-organisational boundary

DEFF Research Database (Denmark)

Jakobsen, Morten

2010-01-01

Purpose - The literature on managing inter-organisational relationships typically suggests managing these relationships based on the formalised exchange of information across the organisational boundary with due respect to trust build-up through successive interactions. This article argues...... that a focus on trust reduces the flexibility and accessibility of resources and hence ruins the advantages of inter-organisational relationships. The article focuses on power as a means for absorbing uncertainty when managing inter-organisational relationships. Methodology - The article is based on findings...... from a case study of inter-organisational relationships. Governmentality is used as a framework for analysing the practise of managing inter-organisational relationships. Findings - A number of representations are employed along the boundary between the case study parties and thereby the boundary...

Evaluation of three electronic report processing systems for preparing hydrologic reports of the U.S Geological Survey, Water Resources Division

Science.gov (United States)

Stiltner, G.J.

1990-01-01

In 1987, the Water Resources Division of the U.S. Geological Survey undertook three pilot projects to evaluate electronic report processing systems as a means to improve the quality and timeliness of reports pertaining to water resources investigations. The three projects selected for study included the use of the following configuration of software and hardware: Ventura Publisher software on an IBM model AT personal computer, PageMaker software on a Macintosh computer, and FrameMaker software on a Sun Microsystems workstation. The following assessment criteria were to be addressed in the pilot studies: The combined use of text, tables, and graphics; analysis of time; ease of learning; compatibility with the existing minicomputer system; and technical limitations. It was considered essential that the camera-ready copy produced be in a format suitable for publication. Visual improvement alone was not a consideration. This report consolidates and summarizes the findings of the electronic report processing pilot projects. Text and table files originating on the existing minicomputer system were successfully transformed to the electronic report processing systems in American Standard Code for Information Interchange (ASCII) format. Graphics prepared using a proprietary graphics software package were transferred to all the electronic report processing software through the use of Computer Graphic Metafiles. Graphics from other sources were entered into the systems by scanning paper images. Comparative analysis of time needed to process text and tables by the electronic report processing systems and by conventional methods indicated that, although more time is invested in creating the original page composition for an electronically processed report , substantial time is saved in producing subsequent reports because the format can be stored and re-used by electronic means as a template. Because of the more compact page layouts, costs of printing the reports were 15% to 25

Impairment Effects as a Career Boundary: A Case Study of Disabled Academics

Science.gov (United States)

Williams, Jannine; Mavin, Sharon

2015-01-01

Within the academic career literature, disabled academics are under-researched, despite calls for career theory development through the exploration of marginalized groups' career experiences and the boundaries which shape these experiences. Here, boundaries refer to the symbolic resources which become reified to construct social boundaries…

Boundary error analysis and categorization in the TRECVID news story segmentation task

NARCIS (Netherlands)

Arlandis, J.; Over, P.; Kraaij, W.

2005-01-01

In this paper, an error analysis based on boundary error popularity (frequency) including semantic boundary categorization is applied in the context of the news story segmentation task from TRECVTD1. Clusters of systems were defined based on the input resources they used including video, audio and

Use and User Perception of Electronic Information Resources: A Case Study of Siva Institute of Frontier Technology, India

Directory of Open Access Journals (Sweden)

Velmurugan Chandran

2013-12-01

Full Text Available The present study aims to explore the use and user perception of electronic resources in Siva Institute of Frontier Technology, India. A total number of 123 users were taken into account for the study through a questionnaire-based survey method. A well-structured questionnaire was designed and distributed to the selected 200 students and staff members. 123 copies of the questionnaires were returned dully filled in and the overall response rate was 61.50 percent. The questionnaire contained both open- and close-ended questions. The collected data were classified, analyzed, and tabulated by using simple statistical methods. This study covers the impact of electronic resources on students and faculty in their academic pursuit.

A preliminary categorization of end-of-life electrical and electronic equipment as secondary metal resources

International Nuclear Information System (INIS)

Oguchi, Masahiro; Murakami, Shinsuke; Sakanakura, Hirofumi; Kida, Akiko; Kameya, Takashi

2011-01-01

Highlights: → End-of-life electrical and electronic equipment (EEE) as secondary metal resources. → The content and the total amount of metals in specific equipment are both important. → We categorized 21 EEE types from contents and total amounts of various metals. → Important equipment types as secondary resources were listed for each metal kind. → Collectability and possible collection systems of various EEE types were discussed. - Abstract: End-of-life electrical and electronic equipment (EEE) has recently received attention as a secondary source of metals. This study examined characteristics of end-of-life EEE as secondary metal resources to consider efficient collection and metal recovery systems according to the specific metals and types of EEE. We constructed an analogy between natural resource development and metal recovery from end-of-life EEE and found that metal content and total annual amount of metal contained in each type of end-of-life EEE should be considered in secondary resource development, as well as the collectability of the end-of-life products. We then categorized 21 EEE types into five groups and discussed their potential as secondary metal resources. Refrigerators, washing machines, air conditioners, and CRT TVs were evaluated as the most important sources of common metals, and personal computers, mobile phones, and video games were evaluated as the most important sources of precious metals. Several types of small digital equipment were also identified as important sources of precious metals; however, mid-size information and communication technology (ICT) equipment (e.g., printers and fax machines) and audio/video equipment were shown to be more important as a source of a variety of less common metals. The physical collectability of each type of EEE was roughly characterized by unit size and number of end-of-life products generated annually. Current collection systems in Japan were examined and potentially appropriate collection

A comparison of grain boundary evolution during grain growth in fcc metals

International Nuclear Information System (INIS)

Brons, J.G.; Thompson, G.B.

2013-01-01

Grain growth of Cu and Ni thin films, subjected to in situ annealing within a transmission electron microscope, has been quantified using a precession-enhanced electron diffraction technique. The orientation of each grain and its misorientation with respect to its neighboring grains were calculated. The Cu underwent grain growth that maintained a monomodal grain size distribution, with its low-angle grain boundaries being consumed, and the Ni exhibited grain size distributions in stages, from monomodal to bimodal to monomodal. The onset of Ni’s abnormal grain growth was accompanied by a sharp increase in the Σ3 and Σ9 boundary fractions, which is attributed to simulation predictions of their increased mobility. These Σ3 and Σ9 fractions then dropped to their room temperature values during the third stage of grain growth. In addition to the Σ3 and Σ9 boundaries, the Σ5 and Σ7 boundaries also underwent an increase in total boundary fraction with increasing temperature in both metals

In-Situ Investigation of Local Boundary Migration During Recrystallization

DEFF Research Database (Denmark)

Zhang, Yubin; Godfrey, Andy; Juul Jensen, Dorte

2014-01-01

A combination of electron channeling contrast (ECC) and electron backscatter diffraction pattern (EBSP) techniques has been used to follow in situ the migration during annealing at 323 K (50 A degrees C) of a recrystallizing boundary through the deformed matrix of high-purity aluminum rolled to 8...

Principles of formation of the content of an educational electronic resource on the basis of general and didactic patterns of learning

Directory of Open Access Journals (Sweden)

Ольга Юрьевна Заславская

2018-12-01

Full Text Available The article considers the influence of the development of technical means of teaching on the effectiveness of educational and methodical resources. Modern opportunities of information and communication technologies allow creating electronic educational resources that represent educational information that automates the learning process, provide information assistance, if necessary, collect and process statistical information on the degree of development of the content of the school material by schoolchildren, set an individual trajectory of learning, and so on. The main principle of data organization is the division of the training course into separate sections on the thematic elements and components of the learning process. General regularities include laws that encompass the entire didactic system, and in specific (particular cases, those whose actions extend to a separate component (aspect of the system. From the standpoint of the existence of three types of electronic training modules in the aggregate content of the electronic learning resource - information, control and module of practical classes - the principles of the formation of the electronic learning resource, in our opinion, should regulate all these components. Each of the certain principles is considered in the groups: scientific orientation, methodological orientation, systemic nature, accounting of interdisciplinary connections, fundamentalization, systematic and dosage sequence, rational use of study time, accessibility, minimization, operationalization of goals, unified identification diagnosis.

Mapping travelling convection vortex events with respect to energetic particle boundaries

Directory of Open Access Journals (Sweden)

T. Moretto

1998-08-01

Full Text Available Thirteen events of high-latitude ionospheric travelling convection vortices during very quiet conditions were identified in the Greenland magnetometer data during 1990 and 1991. The latitudes of the vortex centres for these events are compared to the energetic electron trapping boundaries as identified by the particle measurements of the NOAA 10 satellite. In addition, for all events at least one close DMSP overpass was available. All but one of the 13 cases agree to an exceptional degree that: the TCV centres are located within the region of trapped, high energy electrons close to the trapping boundary for the population of electrons with energy greater than >100 keV. Correspondingly, from the DMSP data they are located within the region of plasmasheet-type precipitation close to the CPS/BPS precipitation boundary. That is, the TCV centres map to deep inside the magnetosphere and not to the magnetopause.Key Words. Ionosphere (Electric fields and currents; Particle precipitation · Magnetospheric physics (Magnetosphere-ionosphere interaction

How grain boundaries affect the efficiency of poly-CdTe solar-cells: A fundamental atomic-scale study of grain boundary dislocation cores using CdTe bi-crystal thin films.

Energy Technology Data Exchange (ETDEWEB)

Klie, Robert [Univ. of Illinois, Chicago, IL (United States)

2016-10-25

It is now widely accepted that grain boundaries in poly-crystalline CdTe thin film devices have a detrimental effect on the minority carrier lifetimes, the open circuit voltage and therefore the overall solar-cell performance. The goal of this project was to develop a fundamental understanding of the role of grain boundaries in CdTe on the carrier life-time, open-circuit voltage, Voc, and the diffusion of impurities. To achieve this goal, i) CdTe bi-crystals were fabricated with various misorientation angels, ii) the atomic- and electronic structures of the grain boundaries were characterized using scanning transmission electron microscopy (STEM), and iii) first-principles density functional theory modeling was performed on the structures determined by STEM to predict the grain boundary potential. The transport properties and minority carrier lifetimes of the bi-crystal grain boundaries were measured using a variety of approaches, including TRPL, and provided feedback to the characterization and modeling effort about the effectiveness of the proposed models.

Fourier analysis and boundary value problems

CERN Document Server

Gonzalez-Velasco, Enrique A

1996-01-01

Fourier Analysis and Boundary Value Problems provides a thorough examination of both the theory and applications of partial differential equations and the Fourier and Laplace methods for their solutions. Boundary value problems, including the heat and wave equations, are integrated throughout the book. Written from a historical perspective with extensive biographical coverage of pioneers in the field, the book emphasizes the important role played by partial differential equations in engineering and physics. In addition, the author demonstrates how efforts to deal with these problems have lead to wonderfully significant developments in mathematics.A clear and complete text with more than 500 exercises, Fourier Analysis and Boundary Value Problems is a good introduction and a valuable resource for those in the field.Key Features* Topics are covered from a historical perspective with biographical information on key contributors to the field* The text contains more than 500 exercises* Includes practical applicati...

Stability, interaction and influence of domain boundaries in Ge/Si(111)-5 × 5

International Nuclear Information System (INIS)

Ondráček, Martin; Mutombo, Pingo; Chvoj, Zdeněk; Chromcová, Zdeňka; Jelínek, Pavel; Mark, Andrew G; McLean, Alastair B

2012-01-01

We present a theoretical investigation of the influence of domain boundaries on the Ge/Si(111)-5 × 5 phase using both large-scale DFT simulations and an analytical model. It is shown that different boundary types modify the atomic and electronic structure of the adjoining 5 × 5 domains in very different ways. A simple theoretical model, that describes the energy interaction J between the boundaries and the 5 × 5 phase, is presented and the interaction energy decay J(x) ≈ x -n for different domain boundaries is estimated. Additionally, the influence of the boundaries on the atomic and electronic structure of adatoms in the parental 5 × 5 phase is analyzed and it is argued that the presence of domain boundaries may strongly affect not only the physical but also the chemical properties of the Ge/Si(111)-5 × 5 phase.

From Millennium ERM to Proquest 360 Resource Manager: Implementing a new Electronic Resources Management System ERMS in an International Graduate Research University in Saudi Arabia

KAUST Repository

Ramli, Rindra M.

2017-05-17

An overview of the Recommendation Study and the subsequent Implementation of a new Electronic Resources Management system ERMS in an international graduate research university in the Kingdom of Saudi Arabia. It covers the timeline, deliverables and challenges as well as lessons learnt by the Project Team.

Electronic structure of twin boundaries in YBa2Cu3O7

International Nuclear Information System (INIS)

Agassi, D.; Kasowski, R.V.

1991-01-01

The electronic structure of a twin boundary (TB) in YBa 2 Cu 3 O 7 is evaluated from ab initio band-structure calculations. Two models are considered: The first assumes the ideal TB atomic configuration. The oxygen-disordered TB model, on the other hand, assumes that in proximity to the TB the oxygen atoms relocate randomly to vacant lattice sites such that the Cu-O bond length is preserved. The calculations have been carried out using 52-atom and 78-atom supercells. For the ideal TB model, the TB presence gives rise to a quasicontinuum of localized states near E F . These states do not contribute to the conductivity. For the oxygen-disordered TB model, two representative oxygen dislocations are considered: One in which a chain oxygen [O(1)] is displaced in the basal plane, and the other in which a Cu-plane oxygen [O(2), O(3)] is up-displaced into the yttrium plane. For both configurations we find conductive pathways with energy near E F . These pathways are comprised of zigzag Cu-O chains, oriented in all directions parallel to the TB plane. This model implies, in particular, percolative conduction in the c-axis direction parallel to the TB planes

22 CFR 1104.12 - Custody of archaeological resources.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Custody of archaeological resources. 1104.12 Section 1104.12 Foreign Relations INTERNATIONAL BOUNDARY AND WATER COMMISSION, UNITED STATES AND MEXICO... resources. (a) Archaeological resources excavated or removed from the public lands remain the property of...

The Synthesis of the Hierarchical Structure of Information Resources for Management of Electronic Commerce Entities

Directory of Open Access Journals (Sweden)

Krutova Anzhelika S.

2017-06-01

Full Text Available The aim of the article is to develop the theoretical bases for the classification and coding of economic information and the scientific justification of the content of information resources of an electronic commerce enterprise. The essence of information resources for management of electronic business entities is investigated. It is proved that the organization of accounting in e-commerce systems is advisable to be built on the basis of two circuits: accounting for financial flows and accounting associated with transformation of business factors in products and services as a result of production activities. There presented a sequence of accounting organization that allows to combine the both circuits in a single information system, which provides a possibility for the integrated replenishment and distributed simultaneous use of the e-commerce system by all groups of users. It is proved that the guarantee of efficient activity of the information management system of electronic commerce entities is a proper systematization of the aggregate of information resources on economic facts and operations of an enterprise in accordance with the management tasks by building the hierarchy of accounting nomenclatures. It is suggested to understand nomenclature as an objective, primary information aggregate concerning a certain fact of the economic activity of an enterprise, which is characterized by minimum requisites, is entered into the database of the information system and is to be reflected in the accounting system. It is proposed to build a database of e-commerce systems as a part of directories (constants, personnel, goods / products, suppliers, buyers and the hierarchy of accounting nomenclatures. The package of documents regulating the organization of accounting at an enterprise should include: the provision on the accounting services, the order on the accounting policy, the job descriptions, the schedules of information exchange, the report card and

Electronic and elemental properties of the Cu{sub 2}ZnSn(S,Se){sub 4} surface and grain boundaries

Energy Technology Data Exchange (ETDEWEB)

Haight, Richard; Shao, Xiaoyan; Wang, Wei; Mitzi, David B. [IBM T. J. Watson Research Center, P.O. Box 218, Yorktown Hts., New York 10598 (United States)

2014-01-20

X-ray and femtosecond UV photoelectron spectroscopy, secondary ion mass spectrometry and photoluminescence imaging were used to investigate the electronic and elemental properties of the CZTS,Se surface and its oxides. Oxide removal reveals a very Cu poor and Zn rich surface relative to bulk composition. O and Na are observed at the surface and throughout the bulk. Upward bending of the valence bands indicates the presence of negative charge in the surface region and the Fermi level is found near the band gap center. The presence of point defects and the impact of these findings on grain boundary properties will be described.

Controlling user access to electronic resources without password

Science.gov (United States)

Smith, Fred Hewitt

2015-06-16

Described herein are devices and techniques for remotely controlling user access to a restricted computer resource. The process includes pre-determining an association of the restricted computer resource and computer-resource-proximal environmental information. Indicia of user-proximal environmental information are received from a user requesting access to the restricted computer resource. Received indicia of user-proximal environmental information are compared to associated computer-resource-proximal environmental information. User access to the restricted computer resource is selectively granted responsive to a favorable comparison in which the user-proximal environmental information is sufficiently similar to the computer-resource proximal environmental information. In at least some embodiments, the process further includes comparing user-supplied biometric measure and comparing it with a predetermined association of at least one biometric measure of an authorized user. Access to the restricted computer resource is granted in response to a favorable comparison.

3D Characterization of Recrystallization Boundaries

DEFF Research Database (Denmark)

Zhang, Yubin; Godfrey, Andrew William; MacDonald, A. Nicole

2016-01-01

A three-dimensional (3D) volume containing a recrystallizing grain and a deformed matrix in a partially recrystallized pure aluminum was characterized using the 3D electron backscattering diffraction technique. The 3D shape of a recrystallizing boundary, separating the recrystallizing grain...... on the formation of protrusions/retrusions....

Numerical equilibrium analysis for structured consumer resource models

NARCIS (Netherlands)

de Roos, A.M.; Diekmann, O.; Getto, P.; Kirkilionis, M.A.

2010-01-01

In this paper, we present methods for a numerical equilibrium and stability analysis for models of a size structured population competing for an unstructured resource. We concentrate on cases where two model parameters are free, and thus existence boundaries for equilibria and stability boundaries

In-situ transmission electron microscopy study of glissile grain boundary dislocation relaxation in a near Σ = 3 {1 1 1} grain boundary in copper

International Nuclear Information System (INIS)

Couzinie, J.P.; Decamps, B.; Boulanger, L.; Priester, L.

2005-01-01

An in-situ annealing experiment has been performed on an intergranular dislocation configuration composed only of glissile grain boundary dislocations observed in a near Σ = 3 {1 1 1} grain boundary in copper. Relaxation phenomena are not obvious than those predicted by theoretical models. Upon annealing, glissile intergranular dislocations are shown to overcome dislocation obstacles by node movement leading to a decrease of the total grain boundary energy

Electronic theses and dissertations: a review of this valuable resource for nurse scholars worldwide.

Science.gov (United States)

Goodfellow, L M

2009-06-01

A worldwide repository of electronic theses and dissertations (ETDs) could provide worldwide access to the most up-to-date research generated by masters and doctoral students. Until that international repository is established, it is possible to access some of these valuable knowledge resources. ETDs provide a technologically advanced medium with endless multimedia capabilities that far exceed the print and bound copies of theses and dissertations housed traditionally in individual university libraries. CURRENT USE: A growing trend exists for universities worldwide to require graduate students to submit theses or dissertations as electronic documents. However, nurse scholars underutilize ETDs, as evidenced by perusing bibliographic citation lists in many of the research journals. ETDs can be searched for and retrieved through several digital resources such as the Networked Digital Library of Theses and Dissertations (http://www.ndltd.org), ProQuest Dissertations and Theses (http://www.umi.com), the Australasian Digital Theses Program (http://adt.caul.edu.au/) and through individual university web sites and online catalogues. An international repository of ETDs benefits the community of nurse scholars in many ways. The ability to access recent graduate students' research electronically from anywhere in the world is advantageous. For scholars residing in developing countries, access to these ETDs may prove to be even more valuable. In some cases, ETDs are not available for worldwide access and can only be accessed through the university library from which the student graduated. Public access to university library ETD collections is not always permitted. Nurse scholars from both developing and developed countries could benefit from ETDs.

The electron-atom ionization problem

International Nuclear Information System (INIS)

McCarthy, I.E.

1995-02-01

Methods of calculating electron-atom ionization as a three-body problem with Coulomb boundary conditions are considered. In the absence of a fully-valid computational method for a time-independent experiment the approximation is made that the incident electron experiences a screened potential. Approximations involving a final state that obeys the three-body Coulomb boundary condition are compared with the distorted-wave Born approximation and the convergent close-coupling method. 24 refs., 6 figs

Moessbauer study of solute interactions with the lattice defect and grain boundary

International Nuclear Information System (INIS)

Ishida, Y.

1979-10-01

Moessbauer effect was used in the investigations of defect structures of Al- 57 Co alloys introduced by electron irradiation and grain boundary embrittlement in binary iron alloys containing sup(119m)Sn nuclei. The behaviour of tin during aging of Al-Cu-Sn alloys was examined by Moessbauer spectra during isothermal annealing of the samples at various temperatures. Similar investigations were conducted for polycrystalline and bicrystalline silver foils containing sup(119m)Sn sandwiched in the boundary. The binding state of tin atoms segregated at the grain boundary of fine grained iron and iron alloys provided the clues for the embrittlement of iron alloys. The inhibiting effect of Ti, V, and Mo can be explained by the usurpation of the electrons in the tin atoms to the 3d shell of iron. Moessbauer effect was extensively applied in studying the aging behaviour of aluminium alloys in quenching, ion-implantation and electron irradiation processes

School Boundaries: Finding Solutions While Gaining Community Support

Science.gov (United States)

Lazarus, William

2010-01-01

Some of the most complicated issues facing school districts across the country revolve around resource allocation and student assignment planning. Determining school attendance boundaries, selecting sites for new schools, closing existing ones, balancing seat utilization while minimizing travel costs, and achieving socioeconomic diversity are all…

Library resources on the Internet

Science.gov (United States)

Buchanan, Nancy L.

1995-07-01

Library resources are prevalent on the Internet. Library catalogs, electronic books, electronic periodicals, periodical indexes, reference sources, and U.S. Government documents are available by telnet, Gopher, World Wide Web, and FTP. Comparatively few copyrighted library resources are available freely on the Internet. Internet implementations of library resources can add useful features, such as full-text searching. There are discussion lists, Gophers, and World Wide Web pages to help users keep up with new resources and changes to existing ones. The future will bring more library resources, more types of library resources, and more integrated implementations of such resources to the Internet.

Metallographic screening of grain boundary engineered type 304 austenitic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Hanning, F., E-mail: Fabian.Hanning@googlemail.com; Engelberg, D.L., E-mail: Dirk.engelberg@manchester.ac.uk

2014-08-15

An electrochemical etching method for the identification of grain boundary engineered type 304 austenitic stainless steel microstructures is described. The method can be applied for rapid microstructure screening to complement electron backscatter diffraction analysis. A threshold parameter to identify grain boundary engineered microstructure is proposed, and the application of metallographic etching for characterising the degree of grain boundary engineering discussed. - Highlights: • As-received (annealed) and grain boundary engineered microstructures were compared. • Electro-chemical polarisation in nitric acid solutions was carried out. • A metallographic screening method has been developed. • The screening method complements EBSD analysis for microstructure identification.

ELECTRONIC EDUCATIONAL RESOURCES FOR ONLINE SUPPORT OF MODERN CHEMISTRY CLASSES IN SPECIALIZED SCHOOL

Directory of Open Access Journals (Sweden)

Maria D. Tukalo

2013-09-01

Full Text Available This article contains material of some modern electronic educational resources that can be used via the Internet to support the modern chemistry classes in specialized school. It was drawn attention to the educational chemical experiments as means of knowledge; simulated key motivational characteristics to enhance students interest for learning subjects, their cognitive and practical activity in the formation of self-reliance and self-creative; commented forecasts for creating of conditions to enhance the creative potential of students in a modern learning environment.

Selection and Evaluation of Electronic Resources

Directory of Open Access Journals (Sweden)

Doğan Atılgan

2013-11-01

Full Text Available Publication boom and issues related to controlling and accession of printed sources have created some problems after World War II. Consequently, publishing industry has encountered the problem of finding possible solution for emerged situation. Industry of electronic publishing has started to improve with the rapid increase of the price of printed sources as well as the problem of publication boom. The first effects of electronic publishing were appeared on the academic and scholarly publications then electronic publishing became a crucial part of all types of publications. As a result of these developments, collection developments and service policies of information centers were also significantly changed. In this article, after a general introduction about selection and evaluation processes of electronic publications, the subscribed databases by a state and a privately owned university in Turkey and their usage were examined.

An Exploratory study on the use of LibAnswers to Resolve, Track and Monitor Electronic Resources Issues: The KAUST Library experience

KAUST Repository

Ramli, Rindra M.

2017-01-01

An Exploratory study on KAUST library use of LibAnswers in resolving electronic resources questions received in LibAnswers. It describes the findings of the questions received in LibAnswers. The author made suggestions based on the findings to improve the reference services in responding to e-resources questions.

An Exploratory study on the use of LibAnswers to Resolve, Track and Monitor Electronic Resources Issues: The KAUST Library experience

KAUST Repository

Ramli, Rindra M.

2017-05-03

An Exploratory study on KAUST library use of LibAnswers in resolving electronic resources questions received in LibAnswers. It describes the findings of the questions received in LibAnswers. The author made suggestions based on the findings to improve the reference services in responding to e-resources questions.

Open Informational Ecosystems: The Missing Link for Sharing Educational Resources

Directory of Open Access Journals (Sweden)

Michael Kerres

2015-02-01

Full Text Available Open educational resources are not available “as such”. Their provision relies on a technological infrastructure of related services that can be described as an informational ecosystem. A closed informational ecosystem keeps educational resources within its boundary. An open informational ecosystem relies on the concurrence of independent stakeholders that jointly provide (meta- information also beyond its boundaries. Mechanisms of open informational ecosystems are described and how they contribute to the delivery of educational resources and to opening education. The paper describes the case of the German Bildungsserver that aims at establishing a federated network of providers of open and closed educational resources. It points out that the design of (inter-national informational ecosystems has a major influence on the future of open educational resources in education.

Galerkin methods for Boltzmann-Poisson transport with reflection conditions on rough boundaries

Science.gov (United States)

Morales Escalante, José A.; Gamba, Irene M.

2018-06-01

We consider in this paper the mathematical and numerical modeling of reflective boundary conditions (BC) associated to Boltzmann-Poisson systems, including diffusive reflection in addition to specularity, in the context of electron transport in semiconductor device modeling at nano scales, and their implementation in Discontinuous Galerkin (DG) schemes. We study these BC on the physical boundaries of the device and develop a numerical approximation to model an insulating boundary condition, or equivalently, a pointwise zero flux mathematical condition for the electron transport equation. Such condition balances the incident and reflective momentum flux at the microscopic level, pointwise at the boundary, in the case of a more general mixed reflection with momentum dependant specularity probability p (k →). We compare the computational prediction of physical observables given by the numerical implementation of these different reflection conditions in our DG scheme for BP models, and observe that the diffusive condition influences the kinetic moments over the whole domain in position space.

The level of the usage of the human resource information system and electronic recruitment in Croatian companies

Directory of Open Access Journals (Sweden)

Snježana Pivac

2014-12-01

Full Text Available Performing business according to contemporary requirements influences companies for continuous usage of modern managerial tools, such as a human resource information system (HRIS and electronic recruitment (ER. Human resources have been recognised as curtail resources and the main source of a competitive advantage in creation of successful business performance. In order to attract and select the top employees, companies use quality information software for attracting internal ones, and electronic recruitment for attracting the best possible external candidates. The main aim of this paper is to research the level of the usage of HRIS and ER within medium-size and large Croatian companies. Moreover, the additional aim of this paper is to evaluate the relationship among the usage of these modern managerial tools and the overall success of human resource management within these companies. For the purpose of this paper, primary and secondary research has been conducted in order to reveal the level of the usage of HRIS and ER as well as the overall success of human resource management in Croatian companies. The companies’ classification (HRIS and ER is done by using the non-hierarchical k-means cluster method as well as the nonparametric Kruskal Wallis test. Further, the companies are ranked by the multicriteria PROMETHEE method. Relevant nonparametric tests are used for testing the overall companies’ HRM. Finally, binary logistic regression is estimated, relating binary variable HRM and HRIS development. After detailed research, it can be concluded that large Croatian companies apply HRIS in majority (with a positive relation to HRM performance, but still require certain degrees of its development.

Equilibrium structure of the plasma sheet boundary layer-lobe interface

Science.gov (United States)

Romero, H.; Ganguli, G.; Palmadesso, P.; Dusenbery, P. B.

1990-01-01

Observations are presented which show that plasma parameters vary on a scale length smaller than the ion gyroradius at the interface between the plasma sheet boundary layer and the lobe. The Vlasov equation is used to investigate the properties of such a boundary layer. The existence, at the interface, of a density gradient whose scale length is smaller than the ion gyroradius implies that an electrostatic potential is established in order to maintain quasi-neutrality. Strongly sheared (scale lengths smaller than the ion gyroradius) perpendicular and parallel (to the ambient magnetic field) electron flows develop whose peak velocities are on the order of the electron thermal speed and which carry a net current. The free energy of the sheared flows can give rise to a broadband spectrum of electrostatic instabilities starting near the electron plasma frequency and extending below the lower hybrid frequency.

The electronic encapsulation of knowledge in hydraulics, hydrology and water resources

Science.gov (United States)

Abbott, Michael B.

The rapidly developing practice of encapsulating knowledge in electronic media is shown to lead necessarily to the restructuring of the knowledge itself. The consequences of this for hydraulics, hydrology and more general water-resources management are investigated in particular relation to current process-simulation, real-time control and advice-serving systems. The generic properties of the electronic knowledge encapsulator are described, and attention is drawn to the manner in which knowledge 'goes into hiding' through encapsulation. This property is traced in the simple situations of pure mathesis and in the more complex situations of taxinomia using one example each from hydraulics and hydrology. The consequences for systems architectures are explained, pointing to the need for multi-agent architectures for ecological modelling and for more general hydroinformatics systems also. The relevance of these developments is indicated by reference to ongoing projects in which they are currently being realised. In conclusion, some more general epistemological aspects are considered within the same context. As this contribution is so much concerned with the processes of signification and communication, it has been partly shaped by the theory of semiotics, as popularised by Eco ( A Theory of Semiotics, Indiana University, Bloomington, 1977).

RESEARCH OF INFLUENCE OF QUALITY OF ELECTRONIC EDUCATIONAL RESOURCES ON QUALITY OF TRAINING WITH USE OF DISTANCE TECHNOLOGIES

Directory of Open Access Journals (Sweden)

H. M. Kravtsov

2013-03-01

Full Text Available Communication improving of educational processes requires today new approaches to the management arrangements and forming of educational policy in the field of distance learning, which is based on the use of modern information and communication technologies. An important step in this process is the continuous monitoring of the development and implementation of information technology and, in particular, the distance learning systems in higher educational establishments. The main objective of the monitoring is the impact assessment on the development of distance learning following the state educational standards, curricula, methodical and technical equipment and other factors; factors revelation that influence the implementation and outcomes of distance learning; results comparison of educational institution functioning and distance education systems in order to determine the most efficient ways of its development. The paper presents the analysis results of the dependence of the quality of educational services on the electronic educational resources. Trends in educational services development was studied by comparing the quality influence of electronic educational resources on the quality of educational services of higher pedagogical educational institutions of Ukraine as of 2009-2010 and 2012-2013. Generally, the analysis of the survey results allows evaluating quality of the modern education services as satisfactory and it can be said that almost 70% of the success of their future development depends on the quality of the used electronic educational resources and distance learning systems in particular.

Role of boundary plasma in lower-hybrid-frequency heating of a tokamak

International Nuclear Information System (INIS)

Uehara, Kazuya; Yamamoto, Takumi; Fujii, Tsuneyuki

1982-01-01

Boundary plasma of a circular tokamak has been investigated by means of electrostatic probes during lower-hybrid heating. The reflection coefficient is affected by the density gradient in front of the launcher. An effective ion heating is performed in the main plasma region when the boundary electron temperature is relatively high enough to suppress the parametric decay instabilities. The simultaneous injection of neutral beams as well as the lower-hybrid wave brings the suppression of instabilities with increase of the electron temperature coming from the neutral beam heating. (author)

Electronic grain boundary properties in polycrystalline Cu(In,Ga)Se2 semiconductors for thin film solar cells

International Nuclear Information System (INIS)

Baier, Robert

2012-01-01

Solar cells based on polycrystalline Cu(In,Ga)Se 2 (CIGSe) thin film absorbers reach the highest energy conversion efficiency among all thin film solar cells. The record efficiency is at least partly attributed to benign electronic properties of grain boundaries (GBs) in the CIGSe layers. However, despite a high amount of research on this phenomenon the underlying physics is not sufficiently understood. This thesis presents an elaborate study on the electronic properties of GBs in CIGSe thin films. Kelvin probe force microscopy (KPFM) was employed to investigate the electronic properties of GBs in dependence of the Ga-content. Five CIGSe thin lms with various Ga-contents were grown by means of similar three stage co-evaporation processes. Both as grown as well as chemically treated (KCN etched) thin films were analyzed. The chemical treatment was employed to remove surface oxides. No difference in electronic GB properties was found with or without the chemical treatment. Therefore, we conclude that a moderate surface oxidation does not alter the electronic properties of GBs. In general, one can observe significant variations of electronic potential barriers at GBs. Under consideration of the averaging effect of the work function signal of nanoscale potential distributions in KPFM measurements which was quantified in the course of this thesis both positive and negative potential barriers in a range between ∼-350 mV and ∼+450 mV were detected. Additionally, variations in the defect densities at GBs between ∼3.1 x 10 11 cm -2 and ∼2.1 x 10 12 cm -2 were found. However, no correlation between the electronic properties of GBs and the Ga-content of CIGSe thin films was discovered. Consequently, one cannot explain the drop in device efficiency observed for CIGSe thin film solar cells with a high Ga-content by a change of the electronic properties of GBs. Combined KPFM and electron backscatter diffraction measurements were employed for the first time on CIGSe thin

Direct imaging of grain boundaries

International Nuclear Information System (INIS)

Gronsky, R.

1979-09-01

There are currently two types of microscopes which, in principle, are capable of imaging atom positions at grain boundaries. One, the field ion microscope (FIM), yields a projection of the specimen surface (approximately stereographic) by field ionization of an imaging gas at protruding atom sites, and provides topographic information in high-index pole regions which may be interpreted atom-by-atom. The other, a transmission electron microscope (TEM), yields a projection (approximately linear) of the entire specimen thickness by electron optical imaging, and provides atomic resolution detail throughout the illuminated area. In this paper, both methods are described and compared, using examples from practical materials systems

Tracking the Flow of Resources in Electronic Waste - The Case of End-of-Life Computer Hard Disk Drives.

Science.gov (United States)

Habib, Komal; Parajuly, Keshav; Wenzel, Henrik

2015-10-20

Recovery of resources, in particular, metals, from waste flows is widely seen as a prioritized option to reduce their potential supply constraints in the future. The current waste electrical and electronic equipment (WEEE) treatment system is more focused on bulk metals, where the recycling rate of specialty metals, such as rare earths, is negligible compared to their increasing use in modern products, such as electronics. This study investigates the challenges in recovering these resources in the existing WEEE treatment system. It is illustrated by following the material flows of resources in a conventional WEEE treatment plant in Denmark. Computer hard disk drives (HDDs) containing neodymium-iron-boron (NdFeB) magnets were selected as the case product for this experiment. The resulting output fractions were tracked until their final treatment in order to estimate the recovery potential of rare earth elements (REEs) and other resources contained in HDDs. The results further show that out of the 244 kg of HDDs treated, 212 kg comprising mainly of aluminum and steel can be finally recovered from the metallurgic process. The results further demonstrate the complete loss of REEs in the existing shredding-based WEEE treatment processes. Dismantling and separate processing of NdFeB magnets from their end-use products can be a more preferred option over shredding. However, it remains a technological and logistic challenge for the existing system.

Reversible twin boundary migration between α″ martensites in a Ti-Nb-Zr-Sn alloy

Energy Technology Data Exchange (ETDEWEB)

Yao, Tingting; Du, Kui, E-mail: kuidu@imr.ac.cn; Wang, Haoliang; Qi, Lu; He, Suyun; Hao, Yulin; Yang, Rui; Ye, Hengqiang

2017-03-14

Cyclic tensile loading tests and transmission electron microscopy investigation are conducted on a Ti-24Nb-4Zr-8Sn (wt%) alloy. Under tensile strain less than 3.3%, most of the deformation strain recovers after unloading but significant energy dissipation occurs during the loading-unloading cycle. Reversible migration of twin boundaries between α″ martensite variants, in virtue of dislocation movement on the twin boundaries, has been revealed by time resolved high-resolution transmission electron microscopy. This twin boundary migration contributes to the energy dissipation effect and consequently the damping property of the titanium alloy.

Effect of boundary conditions on radial mode structure of whistlers

International Nuclear Information System (INIS)

Boswell, R.W.

1983-01-01

The dispersion of the radical eigen modes of a cylindrical m=1 whistler wave with Ωsub(i) << ω << Ωsub(e) << ωsub(pe) are investigated for both conducting and insulating boundaries, where Ωsub(e) and Ωsub(i) are the electron and ion gyro frequencies, Ωsub(pe) is the electron plasma frequency. The effects of electron inertia and resistivity on the modes are discussed

Electrons in the boundary layers near the dayside magnetopause

International Nuclear Information System (INIS)

Hall, D.S.; Chaloner, C.P.; Bryant, D.A.; Lepine, D.R.; Tritakis, V.P.

1990-10-01

Entry of heated solar-wind plasma into the magnetosphere is examined using electron distributions. In particular, the angular structure of the electron distributions is studied within the transition region separating the magnetosheath from the inner magnetosphere. The measurements suggest that electrons in the outer part of the transition region originate in the magnetosheath, whilst the population closer to the Earth consists of electrons from the magnetosphere combined with an energized magnetosheath component. This energized component contains ''counterstreaming'' electrons, which are confined to directions closely parallel and anti-parallel to the magnetic field direction. The possibilities, that the energization of the counterstreaming electrons is cumulatively gained from either waves, electric fields perpendicular to the magnetic field, or quasi-Fermi acceleration, are discussed. It is not possible to identify the topology of the magnetic fields of the outer part of the region, but there is strong evidence that the inner part is on closed magnetic field lines, which map to the dayside auroral zone. The outer part of the transition region is a plasma depletion/magnetic-field compression layer. The structure of the transition region is similar to that surrounding flux transfer events, which leads to the deduction that the plasma and field signatures of flux transfer events may be the result of displacement of the transition region earthwards. Cases where the displacement is such that the field maximum of the depletion/compression region is encountered, may well explain ''crater'' flux transfer event signatures. (author)

Managing collaboration across boundaries in health information technology projects.

Science.gov (United States)

Garrety, Karin; Dalley, Andrew; McLoughlin, Ian; Wilson, Rob; Yu, Ping

2012-01-01

One reason that it is so difficult to build electronic systems for collecting and sharing health information is that their design and implementation requires clear goals and a great deal of collaboration among people from diverse social and occupational worlds. This paper uses empirical examples from two Australian health informatics projects to illustrate the importance of boundary objects and boundary spanning activities in facilitating the high degree of collaboration required for the design and implementation of workable systems.

Electron accelerator shielding design of KIPT neutron source facility

Energy Technology Data Exchange (ETDEWEB)

Zhong, Zhao Peng; Gohar, Yousry [Argonne National Laboratory, Argonne (United States)

2016-06-15

The Argonne National Laboratory of the United States and the Kharkov Institute of Physics and Technology of the Ukraine have been collaborating on the design, development and construction of a neutron source facility at Kharkov Institute of Physics and Technology utilizing an electron-accelerator-driven subcritical assembly. The electron beam power is 100 kW using 100-MeV electrons. The facility was designed to perform basic and applied nuclear research, produce medical isotopes, and train nuclear specialists. The biological shield of the accelerator building was designed to reduce the biological dose to less than 5.0e-03 mSv/h during operation. The main source of the biological dose for the accelerator building is the photons and neutrons generated from different interactions of leaked electrons from the electron gun and the accelerator sections with the surrounding components and materials. The Monte Carlo N-particle extended code (MCNPX) was used for the shielding calculations because of its capability to perform electron-, photon-, and neutron-coupled transport simulations. The photon dose was tallied using the MCNPX calculation, starting with the leaked electrons. However, it is difficult to accurately tally the neutron dose directly from the leaked electrons. The neutron yield per electron from the interactions with the surrounding components is very small, ∼0.01 neutron for 100-MeV electron and even smaller for lower-energy electrons. This causes difficulties for the Monte Carlo analyses and consumes tremendous computation resources for tallying the neutron dose outside the shield boundary with an acceptable accuracy. To avoid these difficulties, the SOURCE and TALLYX user subroutines of MCNPX were utilized for this study. The generated neutrons were banked, together with all related parameters, for a subsequent MCNPX calculation to obtain the neutron dose. The weight windows variance reduction technique was also utilized for both neutron and photon dose

Crossing boundaries in a collaborative modeling workspace

Science.gov (United States)

Morisette, Jeffrey T.; Cravens, Amanda; Miller, Brian W.; Talbert, Marian; Talbert, Colin; Jarnevich, Catherine S.; Fink, Michelle; Decker, Karin; Odell, Eric

2017-01-01

There is substantial literature on the importance of bridging across disciplinary and science–management boundaries. One of the ways commonly suggested to cross boundaries is for participants from both sides of the boundary to jointly produce information (i.e., knowledge co-production). But simply providing tools or bringing people together in the same room is not sufficient. Here we present a case study documenting the mechanisms by which managers and scientists collaborated to incorporate climate change projections into Colorado’s State Wildlife Action Plan. A critical component of the project was the use of a collaborative modeling and visualization workspace: the U.S. Geological Survey’s Resource for Advanced Modeling (RAM). Using video analysis and pre/post surveys from this case study, we examine how the RAM facilitated cognitive and social processes that co-produced a more salient and credible end product. This case provides practical suggestions to scientists and practitioners who want to implement actionable science.

Structure of grain boundaries in hexagonal materials

International Nuclear Information System (INIS)

Sarrazit, F.

1998-05-01

The work presented in this thesis describes experimental and theoretical aspects associated with the structure of grain boundaries in hexagonal materials. It has been found useful to classify grain boundaries as low-angle, special or general on the basis of their structure. High-angle grain boundaries were investigated in tungsten carbide (WC) using conventional electron microscopy techniques, and three examples characteristic of the interfaces observed in this material were studied extensively. Three-dimensionally periodic patterns are proposed as plausible reference configurations, and the Burgers vectors of observed interfacial dislocations were predicted using a theory developed recently. The comparison of experimental observations with theoretical predictions proved to be difficult as contrast simulation techniques require further development for analysis to be completed confidently. Another part of this work involves the characterisation of high-angle grain boundaries in zinc oxide (ZnO) using circuit mapping. Two boundaries displayed structural features characteristic of the 'special' category, however, one boundary presented features which did not conform to this model. It is proposed that the latter observation shows a structural transition from the special to a more general type. Material fluxes involved in defect interactions were considered using the topological framework described in this work. A genera) expression was derived for the total flux arising which allows the behaviour of line-defects to be studied in complex interfacial processes. (author)

Determination of compositional ordering at grain boundaries in boron-doped Ni3Al

International Nuclear Information System (INIS)

Mills, M.J.

1989-01-01

The effects of crystal thickness and defocus on the superlattice contrast from HRTEM images have been demonstrated. The results indicate that fine, FCC fringe spacings in the vicinity of these grain boundaries can be produced if the boundary is slightly inclined to the electron beam, creating the false impression that the region is compositionally disordered. For properly chosen defocus conditions and boundary orientation, contrast typical of the ordered structure extends up to the estimated position of the boundary plane. The lack of a distinct disordered region suggests that microplasticity near grain boundaries is not significantly affected by the presence of B, and that its influence must be highly localized to the boundaries

Boundary surface and microstructure analysis of ceramic materials

International Nuclear Information System (INIS)

Woltersdorf, J.; Pippel, E.

1992-01-01

The article introduces the many possibilities of high voltage (HVEM) and high resolution electron microscopy (HREM) for boundary surface and microstructure analysis of ceramic materials. The investigations are limited to ceramic long fibre composites and a ceramic fibre/glass matrix system. (DG) [de

Boundary work of dentists in everyday work.

Science.gov (United States)

Franzén, Cecilia

2012-08-01

The Swedish policy objectives in dental care provision - to meet public demands for dental care and to increase the cost-effectiveness of the service - require dentists to work in teams with dental hygienists and dental nurses. This study focused on the role of dentists in the distribution of work tasks within teams in one Swedish Public Dental Service organisation. Dental clinics were viewed as micro-political arenas in which dentists attempt to demarcate professional boundaries in response to teamwork. Semi-structured interviews, observations and documents were used. The interviewed individuals were seven dentists employed at two clinics, the managers of each clinic and the general manager. The dentists were interviewed to investigate how they defend or blur professional boundaries. They were also observed at work. The clinic managers and the general manager were interviewed to identify their expectations of dentists concerning work division. The documents comprised organisational plans and annual reports. Dentists demarcated professional boundaries by utilising various power resources: treatment responsibility, specialist knowledge, discretion, and avoidance of work considered to be low status work. The dentists also contributed to blurred boundaries between themselves and the other dental professionals by discussing patient treatment, giving and receiving advice, and assisting the others in skill development. Although dentists' boundary work could obstruct implementation of policy objectives, dentists' behaviour contributed to effective collaboration within the teams. © 2012 John Wiley & Sons A/S.

Chevron defect at the intersection of grain boundaries with free surfaces in Au

International Nuclear Information System (INIS)

Radetic, T.; Lancon, F.; Dahmen, U.

2002-01-01

We have identified a new defect at the intersection between grain boundaries and surfaces in Au using atomic resolution transmission electron microscopy. At the junction line of 90 deg. tilt grain boundaries of (110)-(001) orientation with the free surface, a small segment of the grain boundary, about 1 nm in length, dissociates into a triangular region with a chevronlike stacking disorder and a distorted hcp structure. The structure and stability of these defects are confirmed by atomistic simulations, and we point out the relationship with the one-dimensional incommensurate structure of the grain boundary

Coherent transition radiation from a laser wakefield accelerator as an electron bunch diagnostic

International Nuclear Information System (INIS)

Tilborg, J. van; Geddes, C.G.R.; Toth, C.; Esarey, E.; Schroeder, C.B.; Martin, M.C.; Hao, Z.; Leemans, W.P.

2004-01-01

The observation and modeling of coherent transition radiation from femtosecond laser accelerated electron bunches is discussed. The coherent transition radiation, scaling quadratically with bunch charge, is generated as the electrons transit the plasma-vacuum boundary. Due to the limited transverse radius of the plasma boundary, diffraction effects will strongly modify the angular distribution and the total energy radiated is reduced compared to an infinite transverse boundary. The multi-nC electron bunches, concentrated in a length of a few plasma periods (several tens of microns), experience partial charge neutralization while propagating inside the plasma towards the boundary. This reduces the space-charge blowout of the beam, allowing for coherent radiation at relatively high frequencies (several THz). The charge distribution of the electron bunch at the plasma-vacuum boundary can be derived from Fourier analysis of the coherent part of the transition radiation spectrum. A Michelson interferometer was used to measure the coherent spectrum, and electron bunches with duration on the order of 50 fs (rms) were observed

The time development of the plasma-glass boundary layer in a T-tube

International Nuclear Information System (INIS)

Pavlov, M.; Djurovic, S.

1982-01-01

The refraction of a laser beam by a flat boundary layer between the plasma and the glass plate is analysed. A boundary layer with a constant gradient electron density is assumed. Results of the analysis for plasmas produced in a small T-tube show that the boundary layer thickness increases with time faster than linearly. This means that a relatively fast collapse due to cooling through the boundary layer happens at the second half of the reflected plasma life time, while the boundary layer is negligible thin during the first 2μs after the reflected shock front has passed the point of observation. (author)

22 CFR 1104.17 - Confidentiality of archaeological resource information.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Confidentiality of archaeological resource information. 1104.17 Section 1104.17 Foreign Relations INTERNATIONAL BOUNDARY AND WATER COMMISSION, UNITED... of archaeological resource information. (a) The Commissioner shall not make available to the public...

Bandgap tunability at single-layer molybdenum disulphide grain boundaries

KAUST Repository

Huang, Yu Li

2015-02-17

Two-dimensional transition metal dichalcogenides have emerged as a new class of semiconductor materials with novel electronic and optical properties of interest to future nanoelectronics technology. Single-layer molybdenum disulphide, which represents a prototype two-dimensional transition metal dichalcogenide, has an electronic bandgap that increases with decreasing layer thickness. Using high-resolution scanning tunnelling microscopy and spectroscopy, we measure the apparent quasiparticle energy gap to be 2.40±0.05 eV for single-layer, 2.10±0.05 eV for bilayer and 1.75±0.05 eV for trilayer molybdenum disulphide, which were directly grown on a graphite substrate by chemical vapour deposition method. More interestingly, we report an unexpected bandgap tunability (as large as 0.85±0.05 eV) with distance from the grain boundary in single-layer molybdenum disulphide, which also depends on the grain misorientation angle. This work opens up new possibilities for flexible electronic and optoelectronic devices with tunable bandgaps that utilize both the control of two-dimensional layer thickness and the grain boundary engineering.

Control of Resources for Economic Development in Food Networks

DEFF Research Database (Denmark)

Brink, Tove

2010-01-01

The challenge of economic development in the 21st century is linked to innovation. Enabling innovation contains a wide span from the new idea to learning how to provide value through the new idea and continuing to how to control resources to perform at prime. The focus in this paper is set on how...... to control resources for innovation to add value and economic development. This paper reveals how crossing dynamic composite underlying boundaries can have an impact on control of resources for economic development in food networking SMEs .The analyses in this paper shows the broad and significant impact....... Connections are revealed to have no significant influence on the internal control of resources but a significant direct influence on economic development through value chain activities. Through the analyses in this paper the notion of ‘boundary utility’ is elaborated as the crossing and transformation...

SILICON CARBIDE GRAIN BOUNDARY DISTRIBUTIONS, IRRADIATION CONDITIONS, AND SILVER RETENTION IN IRRADIATED AGR-1 TRISO FUEL PARTICLES

Energy Technology Data Exchange (ETDEWEB)

Lillo, T. M.; Rooyen, I. J.; Aguiar, J. A.

2016-11-01

Precession electron diffraction in the transmission electron microscope was used to map grain orientation and ultimately determine grain boundary misorientation angle distributions, relative fractions of grain boundary types (random high angle, low angle or coincident site lattice (CSL)-related boundaries) and the distributions of CSL-related grain boundaries in the SiC layer of irradiated TRISO-coated fuel particles. Two particles from the AGR-1 experiment exhibiting high Ag-110m retention (>80%) were compared to a particle exhibiting low Ag-110m retention (<19%). Irradiated particles with high Ag-110m retention exhibited a lower fraction of random, high angle grain boundaries compared to the low Ag-110m retention particle. An inverse relationship between the random, high angle grain boundary fraction and Ag-110m retention is found and is consistent with grain boundary percolation theory. Also, comparison of the grain boundary distributions with previously reported unirradiated grain boundary distributions, based on SEM-based EBSD for similarly fabricated particles, showed only small differences, i.e. a greater low angle grain boundary fraction in unirradiated SiC. It was, thus, concluded that SiC layers with grain boundary distributions susceptible to Ag-110m release were present prior to irradiation. Finally, irradiation parameters were found to have little effect on the association of fission product precipitates with specific grain boundary types.

Bicultural Resourcefulness in Global Management

DEFF Research Database (Denmark)

Clausen, Lisbeth; Keita, Maria H.

2016-01-01

Biculturals are increasingly viewed as a resource in global business. They are effective in multicultural teams, they are great boundary spanners between corporate headquarters and their subsidiaries, and their abilities are acknowl-edged in cross-cultural leadership. This article aims to generate...

The Pinning by Particles of Low and High Angle Grain Boundaries during Grain Growth

DEFF Research Database (Denmark)

Tweed, C.J.; Ralph, B.; Hansen, Niels

1984-01-01

A study has been made using transmission electron microscopy of the pinning of grain boundaries in aluminium during grain growth by fine dispersions of alumina particles. The boundary parameters have been determined with precision and the pinning effects measured using an approach due to Ashby...

Electronic grain boundary properties in polycrystalline Cu(In,Ga)Se{sub 2} semiconductors for thin film solar cells

Energy Technology Data Exchange (ETDEWEB)

Baier, Robert

2012-06-25

Solar cells based on polycrystalline Cu(In,Ga)Se{sub 2} (CIGSe) thin film absorbers reach the highest energy conversion efficiency among all thin film solar cells. The record efficiency is at least partly attributed to benign electronic properties of grain boundaries (GBs) in the CIGSe layers. However, despite a high amount of research on this phenomenon the underlying physics is not sufficiently understood. This thesis presents an elaborate study on the electronic properties of GBs in CIGSe thin films. Kelvin probe force microscopy (KPFM) was employed to investigate the electronic properties of GBs in dependence of the Ga-content. Five CIGSe thin lms with various Ga-contents were grown by means of similar three stage co-evaporation processes. Both as grown as well as chemically treated (KCN etched) thin films were analyzed. The chemical treatment was employed to remove surface oxides. No difference in electronic GB properties was found with or without the chemical treatment. Therefore, we conclude that a moderate surface oxidation does not alter the electronic properties of GBs. In general, one can observe significant variations of electronic potential barriers at GBs. Under consideration of the averaging effect of the work function signal of nanoscale potential distributions in KPFM measurements which was quantified in the course of this thesis both positive and negative potential barriers in a range between ∼-350 mV and ∼+450 mV were detected. Additionally, variations in the defect densities at GBs between ∼3.1 x 10{sup 11} cm{sup -2} and ∼2.1 x 10{sup 12} cm{sup -2} were found. However, no correlation between the electronic properties of GBs and the Ga-content of CIGSe thin films was discovered. Consequently, one cannot explain the drop in device efficiency observed for CIGSe thin film solar cells with a high Ga-content by a change of the electronic properties of GBs. Combined KPFM and electron backscatter diffraction measurements were employed for the

Confinement dynamics and boundary condition studies in the Reversed Field Pinch

International Nuclear Information System (INIS)

Schoenberg, K.F.; Ingraham, J.C.; Moses, R.W. Jr.

1988-01-01

The study of confinement dynamics, including investigation of the boundary conditions required for plasma sustainment, are central to the development of the Reversed Field Pinch (RFP) concept. Recently, several insights into confinement have emerged from a detailed investigation RFP electron and ion dynamics. These insights derive from the recognition that both magnetohydrodynamic (MHD) and electron kinetic effects play an important and coupled role in RFP stability, sustainment, and confinement. In this paper, we summarize the results of confinement studies on the ZT-40M experiment, and boundary condition studies on the Wisconsin non-circular RFP experiment. A brief description of the newly commissioned Madison Symmetric Torus (MST) is also presented. 28 refs., 3 figs

Using mobile electronic devices to deliver educational resources in developing countries.

Science.gov (United States)

Mazal, Jonathan Robert; Ludwig, Rebecca

2015-01-01

Developing countries have far fewer trained radiography professionals than developed countries, which exacerbates the limited access to imaging services. The lack of trained radiographers reflects, in part, limited availability of radiographer-specific educational resources. Historically, organizations that provided such resources in the developing world faced challenges related to the limited stock of current materials as well as expenses associated with shipping and delivery. Four mobile electronic devices (MEDs) were loaded with educational content (e-books, PDFs, and digital applications) spanning major radiography topics. The MEDs were distributed to 4 imaging departments in Ghana, India, Nepal, and Nigeria based on evidence of need for radiography-specific resources, as revealed by survey responses. A cost comparison of postal delivery vs digital delivery of educational content was performed. The effectiveness of delivering additional content via Wi-Fi transmission also was evaluated. Feedback was solicited on users' experience with the MEDs as a delivery tool for educational content. An initial average per e-book expense of $30.05, which included the cost of the device, was calculated for the MED delivery method compared with $15.56 for postal delivery of printed materials. The cost of the MED delivery method was reduced to an average of $10.05 for subsequent e-book deliveries. Additional content was successfully delivered via Wi-Fi transmission to all recipients during the 3-month follow-up period. Overall user feedback on the experience was positive, and ideas for enhancing the MED-based method were identified. Using MEDs to deliver radiography-specific educational content appears to be more cost effective than postal delivery of printed materials on a long-term basis. MEDs are more efficient for providing updates to educational materials. Customization of content to department needs, and using projector devices could enhance the usefulness of MEDs for

Computational Fluid Dynamics model of stratified atmospheric boundary-layer flow

DEFF Research Database (Denmark)

Koblitz, Tilman; Bechmann, Andreas; Sogachev, Andrey

2015-01-01

For wind resource assessment, the wind industry is increasingly relying on computational fluid dynamics models of the neutrally stratified surface-layer. So far, physical processes that are important to the whole atmospheric boundary-layer, such as the Coriolis effect, buoyancy forces and heat...

On the search for experimentally observed grain boundary phase transitions

International Nuclear Information System (INIS)

Balluffi, R.W.; Hsieh, T.E.

1987-07-01

The phase space for a heterogeneous system containing a grain boundary involves a relatively large number of variables (i.e., at least six plus the number of components), and it is therefore conceptually possible to induce a large variety of grain boundary phase transitions by selectively varying these parameters. Despite this, a review of the literature reveals that there have been virtually no clear-cut experimental observations of transitions reported in which the boundary structure has been observed as a function of time under well defined conditions. In current work, we are searching for roughening/faceting transitions and melting transitions for boundaries in Al by hot stage transmission electron microscopy. A clear example of a reversible roughening/faceting transition has been found. No evidence for melting has been found for temperatures as high as 0.96 T/sub m/ (by monitoring GBD core delocalization in several special boundaries with Σ ≤ 13) or 0.999 T/sub m/ (by observing the local diffraction contrast at general boundaries in polycrystalline specimens)

Success criteria for electronic medical record implementations in low-resource settings: a systematic review.

Science.gov (United States)

Fritz, Fleur; Tilahun, Binyam; Dugas, Martin

2015-03-01

Electronic medical record (EMR) systems have the potential of supporting clinical work by providing the right information at the right time to the right people and thus make efficient use of resources. This is especially important in low-resource settings where reliable data are also needed to support public health and local supporting organizations. In this systematic literature review, our objectives are to identify and collect literature about success criteria of EMR implementations in low-resource settings and to summarize them into recommendations. Our search strategy relied on PubMed queries and manual bibliography reviews. Studies were included if EMR implementations in low-resource settings were described. The extracted success criteria and measurements were summarized into 7 categories: ethical, financial, functionality, organizational, political, technical, and training. We collected 381 success criteria with 229 measurements from 47 articles out of 223 articles. Most papers were evaluations or lessons learned from African countries, published from 1999 to 2013. Almost half of the EMR systems served a specific disease area like human immunodeficiency virus (HIV). The majority of criteria that were reported dealt with the functionality, followed by organizational issues, and technical infrastructures. Sufficient training and skilled personnel were mentioned in roughly 10%. Political, ethical, and financial considerations did not play a predominant role. More evaluations based on reliable frameworks are needed. Highly reliable data handling methods, human resources and effective project management, as well as technical architecture and infrastructure are all key factors for successful EMR implementation. © The Author 2015. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Evolution of grain boundary character distributions in alloy 825 tubes during high temperature annealing: Is grain boundary engineering achieved through recrystallization or grain growth?

International Nuclear Information System (INIS)

Bai, Qin; Zhao, Qing; Xia, Shuang; Wang, Baoshun; Zhou, Bangxin; Su, Cheng

2017-01-01

Grain boundary engineering (GBE) of nickel-based alloy 825 tubes was carried out with different cold drawing deformations by using a draw-bench on a factory production line and subsequent annealing at various temperatures. The microstructure evolution of alloy 825 during thermal-mechanical processing (TMP) was characterized by means of the electron backscatter diffraction (EBSD) technique to study the TMP effects on the grain boundary network and the evolution of grain boundary character distributions during high temperature annealing. The results showed that the proportion of ∑ 3 n coincidence site lattice (CSL) boundaries of alloy 825 tubes could be increased to > 75% by the TMP of 5% cold drawing and subsequent annealing at 1050 °C for 10 min. The microstructures of the partially recrystallized samples and the fully recrystallized samples suggested that the proportion of low ∑ CSL grain boundaries depended on the annealing time. The frequency of low ∑ CSL grain boundaries increases rapidly with increasing annealing time associating with the formation of large-size highly-twinned grains-cluster microstructure during recrystallization. However, upon further increasing annealing time, the frequency of low ∑ CSL grain boundaries decreased markedly during grain growth. So it is concluded that grain boundary engineering is achieved through recrystallization rather than grain growth. - Highlights: •The grain boundary engineering (GBE) is applicable to 825 tubes. •GBE is achieved through recrystallization rather than grain growth. •The low ∑ CSL grain boundaries in 825 tubes can be increased to > 75%.

Technology adoption in nonrenewable resource management

International Nuclear Information System (INIS)

Cunha-e-Sa, Maria A.; Balcao Reis, Ana; Roseta-Palma, Catarina

2009-01-01

Technological change has played an important role in models of nonrenewable resource management, since its presence mitigates the depletion effect on extraction costs over time. We formalize the problem of a competitive nonrenewable resource extracting firm faced with the possibility of technology adoption. Based on a quadratic extraction cost function, our results show that the expected net benefits from adoption increase both with the size of the resource stock and with prices. A boundary that separates the region where expected net benefits are positive from the one where they are negative is derived. (author)

Studies of Grain Boundaries in Materials Subjected to Diffusional Creep

DEFF Research Database (Denmark)

Nørbygaard, Thomas

Grain boundaries in crystalline Cu(2%Ni) creep specimens have been studied by use of scanning and transmission electron microscopy in order to establish the mechanism of deformation. Creep rate measurements and dependencies were found to fit reasonably well with the model for diffusional creep......) with the activity displayed during diffusional creep testing. It was found that boundaries with low deviation from perfect Σ did not contribute macroscopically to the creep strain. A resist deposition procedure was examined to improve the reference surface grid so as to allow determination of the grain boundary...... plane by use of simple stereomicroscopy directly on the surface. The etched pattern deteriorated heav-ily during creep testing, supposedly because of dislocation creep, due to exces-sive creep stress. Grain boundaries have been studied and characterised by TEM providing an insight into the diversity...

Transport properties through graphene grain boundaries: strain effects versus lattice symmetry

Science.gov (United States)

Hung Nguyen, V.; Hoang, Trinh X.; Dollfus, P.; Charlier, J.-C.

2016-06-01

As most materials available at the macroscopic scale, graphene samples usually appear in a polycrystalline form and thus contain grain boundaries. In the present work, the effect of uniaxial strain on the electronic transport properties through graphene grain boundaries is investigated using atomistic simulations. A systematic picture of transport properties with respect to the strain and lattice symmetry of graphene domains on both sides of the boundary is provided. In particular, it is shown that strain engineering can be used to open a finite transport gap in all graphene systems where the two domains are arranged in different orientations. This gap value is found to depend on the strain magnitude, on the strain direction and on the lattice symmetry of graphene domains. By choosing appropriately the strain direction, a large transport gap of a few hundred meV can be achieved when applying a small strain of only a few percents. For a specific class of graphene grain boundary systems, strain engineering can also be used to reduce the scattering on defects and thus to significantly enhance the conductance. With a large strain-induced gap, these graphene heterostructures are proposed to be promising candidates for highly sensitive strain sensors, flexible electronic devices and p-n junctions with non-linear I-V characteristics.

Structural defects in multiferroic BiMnO3 studied by transmission electron microscopy and electron energy-loss spectroscopy

International Nuclear Information System (INIS)

Yang, H.; Chi, Z. H.; Yao, L. D.; Zhang, W.; Li, F. Y.; Jin, C. Q.; Yu, R. C.

2006-01-01

The multiferroic material BiMnO 3 synthesized under high pressure has been systematically studied by transmission electron microscopy and electron energy-loss spectroscopy, and some important structural defects are revealed in this multiferroic material. The frequently observed defects are characterized to be Σ3(111) twin boundaries, Ruddlesden-Popper [Acta Crystallogr. 11, 54 (1958)] antiphase boundaries, and a p p superdislocations connected with a small segment of Ruddlesden-Popper defect. These defects are present initially in the as-synthesized sample. In addition, we find that ordered voids (oxygen vacancies) are easily introduced into the multiferroic BiMnO 3 by electron-beam irradiation

Numerical simulation of electron-beam-induced current near a silicon grain boundary and impact of a p-n junction space charge region

Energy Technology Data Exchange (ETDEWEB)

Corkish, R.; Altermatt, P.P.; Heiser, G. [Photovoltaics Special Research Centre, University of New South Wales, 2052 Sydney (Australia)

2001-01-01

Three-dimensional numerical simulations of electron-beam-induced current (EBIC) near a vertical silicon grain boundary are demonstrated. They are compared with an analytical model which excludes the effect of carrier generation other than in the bulk base region of a solar cell structure. We demonstrate that in a wide range of solar cell structures recombination in the space charge region (SCR) significantly affects the EBIC results and hence needs to be included in the data evaluation. Apart from these findings, simulations of a realistic silicon solar cell structure (thick emitter, field-dependent mobility, etc.) are demonstrated.

A New Boundary for the High Plains - Ogallala Aquifer Complex

Science.gov (United States)

Haacker, E. M.; Nozari, S.; Kendall, A. D.

2017-12-01

In the semi-arid Great Plains, water is the key ingredient for crop growth: the difference between meager yields for many crops and an agricultural bonanza. The High Plains-Ogallala Aquifer complex (HPA) underlies 452,000 square kilometers of the region, and over 95% of water withdrawn from the aquifer is used for irrigation. Much of the HPA is being pumped unsustainably, and since the region is heavily reliant on this resource for its social and economic health, the High Plains has been a leader in groundwater management planning. However, the geographic boundary of the High Plains region fails to reflect the hydrogeological realities of the aquifer. The current boundary, recognizable from countless textbooks and news articles, is only slightly modified from a version from the 1980's, and largely follows the physiographic borders of the High Plains - defined by surface features such as escarpments and rivers - rather than the edges of water-bearing sediment sufficient for high-volume pumping. This is supported by three lines of evidence: hydrogeological observations from the original aquifer boundary determination; the extent of irrigated land, as estimated by MODIS-MIrAD data; and statistical estimates of saturated thickness, incorporating improved maps of the aquifer base and an additional 35 years of water table measurements. In this project, new maps of saturated thickness are used to create an updated aquifer boundary, which conforms with the standard definition of an aquifer as a package of sediment that yields enough water to be economically pumped. This has major implications for social and physical models, as well as water planning and estimates of sustainability for the HPA. Much of the area of the HPA that has been labeled `sustainable' based upon estimates of recharge relative to pumping estimates falls outside the updated aquifer boundary. In reality, the sustainably-pumped area of this updated aquifer boundary is far smaller—a fact that if more

Boundary Plasma Turbulence Simulations for Tokamaks

International Nuclear Information System (INIS)

Xu, X.; Umansky, M.; Dudson, B.; Snyder, P.

2008-05-01

The boundary plasma turbulence code BOUT models tokamak boundary-plasma turbulence in a realistic divertor geometry using modified Braginskii equations for plasma vorticity, density (ni), electron and ion temperature (T e ; T i ) and parallel momenta. The BOUT code solves for the plasma fluid equations in a three dimensional (3D) toroidal segment (or a toroidal wedge), including the region somewhat inside the separatrix and extending into the scrape-off layer; the private flux region is also included. In this paper, a description is given of the sophisticated physical models, innovative numerical algorithms, and modern software design used to simulate edge-plasmas in magnetic fusion energy devices. The BOUT code's unique capabilities and functionality are exemplified via simulations of the impact of plasma density on tokamak edge turbulence and blob dynamics

Automated Boundary Conditions for Wind Tunnel Simulations

Science.gov (United States)

Carlson, Jan-Renee

2018-01-01

Computational fluid dynamic (CFD) simulations of models tested in wind tunnels require a high level of fidelity and accuracy particularly for the purposes of CFD validation efforts. Considerable effort is required to ensure the proper characterization of both the physical geometry of the wind tunnel and recreating the correct flow conditions inside the wind tunnel. The typical trial-and-error effort used for determining the boundary condition values for a particular tunnel configuration are time and computer resource intensive. This paper describes a method for calculating and updating the back pressure boundary condition in wind tunnel simulations by using a proportional-integral-derivative controller. The controller methodology and equations are discussed, and simulations using the controller to set a tunnel Mach number in the NASA Langley 14- by 22-Foot Subsonic Tunnel are demonstrated.

Grain boundary precipitation strengthening mechanism in W containing advanced creep resistant ferritic steels

Energy Technology Data Exchange (ETDEWEB)

Shibata, T.; Hasegawa, Y. [Tohoku Univ., Sendai (Japan)

2010-07-01

Grain boundary precipitation strengthening is expected to be a decisive factor in developing ferritic creep resistant steels. This study examined the grain boundary precipitation strengthening mechanism extracting the effect of the tempered martensitic microstructure and precipitates on the high angle grain boundary in M{sub 23}C4{sub 6} type carbide and the Fe{sub 2}W type Laves phase effect of the creep deformation fixing the grain boundary according to transmission electron microscope (TEM) observation. A creep test was carried out at high temperature in order to evaluate the high angle boundary strengthening effect simulating the long-term creep deformation microstructure by the lath structure disappearance. The correlation of the creep rupture time and the grain boundary shielding ratio were found to be independent of precipitate type. The creep deformation model represents block boundary shielding by precipitates as the decisive factor for W containing ferritic creep resistant steels. (orig.)

Metallicity at interphase boundaries due to polar catastrophe induced by charge density discontinuity

KAUST Repository

Albar, Arwa

2018-02-09

The electronic properties of interphase boundaries are of basic importance for most materials, particularly when those properties deviate strongly from the bulk behavior. We introduce a mechanism that can result in metallicity at stoichiometric interphase boundaries between semiconductors based on the idea of polar catastrophe, which is usually considered only in the context of heterostructures. To this end, we perform ab initio calculations within density functional theory to investigate the electronic states at stoichiometric SnO/SnO2 (110) interphase boundaries. In this system, one would not expect polar catastrophe to have a role according to state-of-the-art theory because the interface lacks formal charge discontinuity. However, we observe the formation of a hole gas between the semiconductors SnO and SnO2. To explain these findings, we provide a generalized theory based on the idea that the charge density discontinuity between SnO and SnO2, a consequence of lattice mismatch, drives a polar catastrophe scenario. As a result, SnO/SnO2 (110) interphase boundaries can develop metallicity depending on the grain size. The concept of metallicity due to polar catastrophe induced by charge density discontinuity is of general validity and applies to many interphase boundaries with lattice mismatch.

Surface studies of iridium-alloy grain boundaries associated with weld cracking

International Nuclear Information System (INIS)

Mosley, W.C.

1982-01-01

Plutonium-238 oxide fuel pellets for the General Purpose Heat Source (GPHS) Radioisotopic Thermoelectric Generators to be used on the NASA Galileo Mission to Jupiter and the International Solar Polar Mission are produced and encapsulated in iridium alloy at the Savannah River Plant (SRP). Underbead cracks occasionally occur in the girth weld on the iridium-alloy-clad vent sets in the region where the gas tungsten arc is quenched. Grain-boundary structures and compositions were characterized by scanning electron microscopy/x-ray energy spectroscopy, electron microprobe analysis and scanning Auger microprobe analysis to determine the cause of weld quench area cracking. Results suggest that weld quench area cracking may be caused by gas porosity or liquation in the grain boundaries

Precipitates and boundaries interaction in ferritic ODS steels

Energy Technology Data Exchange (ETDEWEB)

Sallez, Nicolas, E-mail: nicolas.sallez@simap.grenoble-inp.fr [Univ. Grenoble Alpes, SIMAP, F-38000 Grenoble (France); Hatzoglou, Constantinos [Groupe de Physique des Matériaux, Université et INSA de Rouen, UMR CNRS 6634, Normandie Université (France); Delabrouille, Fredéric [EDF–EDF R& D, Les Renardières, 77818 Moret-sur-Loing (France); Sornin, Denis; Chaffron, Laurent [CEA, DEN, Service de Recherches Métallurgiques Appliqué, 91191 Gif-sur-Yvette (France); Blat-Yrieix, Martine [EDF–EDF R& D, Les Renardières, 77818 Moret-sur-Loing (France); Radiguet, Bertrand; Pareige, Philippe [Groupe de Physique des Matériaux, Université et INSA de Rouen, UMR CNRS 6634, Normandie Université (France); Donnadieu, Patricia; Bréchet, Yves [Univ. Grenoble Alpes, SIMAP, F-38000 Grenoble (France)

2016-04-15

In the course of a recrystallization study of Oxide Dispersion Strengthened (ODS) ferritic steels during extrusion, particular interest was paid to the (GB) Grain Boundaries interaction with precipitates. Complementary and corresponding characterization experiments using Transmission Electron Microscopy (TEM), Energy Dispersive X-ray spectroscopy (EDX) and Atom Probe Tomography (APT) have been carried out on a voluntarily interrupted extrusion or extruded samples. Microscopic observations of Precipitate Free Zones (PFZ) and precipitates alignments suggest precipitate interaction with migrating GB involving dissolution and Oswald ripening of the precipitates. This is consistent with the local chemical information gathered by EDX and APT. This original mechanism for ODS steels is similar to what had been proposed in the late 80s for similar observation made on Ti alloys reinforced by nanosized yttrium oxides: An interaction mechanism between grain boundaries and precipitates involving a diffusion controlled process of precipitates dissolution at grain boundaries. It is believed that this mechanism can be of primary importance to explain the mechanical behaviour of such steels. - Highlights: • To study the microstructural evolution of a ferritic ODS steel during its extrusion, observations have been carried on samples resulting from a voluntarily interrupted extrusion and extruded materials. • A highly heterogeneous precipitate population have been observed. Nanosized coherent precipitates (2–5 nm) on both sides of the grain boundaries despite grain boundary migration after precipitation due to further thermo-mechanical processing as well as coarse precipitates (10–40 nm) alignments are observed on the grain boundaries and within the grains, parallel to the grain boundaries. • Asymmetrical PFZs can be observed around precipitates alignments and grain boundaries. Using TEM with EDX and APT we have been able to ensure that the PFZs are chemically depleted. �

JTAG boundary-scan of the Belle II pixel vertex detector

Energy Technology Data Exchange (ETDEWEB)

Leitl, Philipp [Max-Planck-Institut fuer Physik (Germany); Collaboration: Belle II-Collaboration

2016-07-01

For the upgrade of the Vertex Detector at the Belle II experiment, DEPFET sensors will be used. This new technology requires specific electronics for controlling and readout. Therefore three different kinds of Application-Specific Integrated Circuits (ASICs) are mounted very close to the sensors. Because of space limitations ball grid arrays (BGAs) are used for the contacts to the electronic circuitry. After the mounting process this results in a lack of physical access to the electrical connections. With Boundary-Scan tests, following the IEEE Std 1149.1, it is possible to regain access to the pins for interconnection tests. In this way a quality assurance (QA) is possible to verify that the integration was done correctly and that the circuitry and the electronics are working properly. The present user-friendly system is presented, including the description of additionally developed hardware as well as necessary adjustments to the netlist files and Boundary-Scan Description Language (BSDL) Files of the ASICs. Achieved measurement results from the so far produced detector modules are shown.

Slovenian-Croatian boundary: backgrounds of boundary-making and boundary-breaking in Istria regarding the contemporary boundary dispute

Directory of Open Access Journals (Sweden)

Damir Josipovič

2012-06-01

Full Text Available Boundary-making in Istria is an old undertaking. It has actually never ceasesed, not even today. Istrian peninsula has thus undergone substantial boundary shifts during the last couple of centuries (especially after the Venetian demise in 1797. But Istria carries its worldwide fame also due to one of probably the harshest disputes on the post-war European grounds – the Trieste territory dispute. In author's perspective, this dispute is one of the four main corner-stones of the current Slovenian-Croatian boundary dispute. The remaining three include the Kozler's boundary around Dragonja (Rokava River, the ungraspable notions of Austrian censuses in Istria, and the narratives of partisan settlements on military jurisdiction. However, there are other very important aspects which significantly shaped the development of the dispute, but we will focus at assessing the importance of the aforementioned ones. In this sense, the analysis of the effects of the outcome of the Trieste dispute and its implications to the contemporary interstate dispute is set forth. By unveiling its material and consequently its psychological effects upon the contemporary bilateral relations, its analyses simultaneously reveals backgrounds of never answered question, why Kozler's proposed linguistic boundary around Dragonja (Rokava River turned out to become a boundary of national character. Though nowadays disputed, there is absolutely no chance for both involved parties to substantially draw away from once decisively drawn line of a layman. Despite the fierce battle of words in Slovenian public media on whether should the interstate boundary be placed on Mirna (Quieto or Dragonja Rivers, it will be argued here that the actual choice of the Valley of Dragonja as a boundary is by all means Slovenian. The arguments are based on extensive analyses of cartographic materials, relevant literature, documents, and statistical data.

Slovenian-Croatian boundary: backgrounds of boundary-making and boundary-breaking in Istria regarding the contemporary boundary dispute

Directory of Open Access Journals (Sweden)

Damir Josipovič

2012-01-01

Full Text Available Boundary-making in Istria is an old undertaking. It has actually never ceasesed, not even today. Istrian peninsula has thus undergone substantial boundary shifts during the last couple of centuries (especially after the Venetian demise in 1797. But Istria carries its worldwide fame also due to one of probably the harshest disputes on the post-war European grounds – the Trieste territory dispute. In author's perspective, this dispute is one of the four main corner-stones of the current Slovenian-Croatian boundary dispute. The remaining three include the Kozler's boundary around Dragonja (Rokava River, the ungraspable notions of Austrian censuses in Istria, and the narratives of partisan settlements on military jurisdiction. However, there are other very important aspects which significantly shaped the development of the dispute, but we will focus at assessing the importance of the aforementioned ones. In this sense, the analysis of the effects of the outcome of the Trieste dispute and its implications to the contemporary interstate dispute is set forth. By unveiling its material and consequently its psychological effects upon the contemporary bilateral relations, its analyses simultaneously reveals backgrounds of never answered question, why Kozler's proposed linguistic boundary around Dragonja (Rokava River turned out to become a boundary of national character. Though nowadays disputed, there is absolutely no chance for both involved parties to substantially draw away from once decisively drawn line of a layman. Despite the fierce battle of words in Slovenian public media on whether should the interstate boundary be placed on Mirna (Quieto or Dragonja Rivers, it will be argued here that the actual choice of the Valley of Dragonja as a boundary is by all means Slovenian. The arguments are based on extensive analyses of cartographic materials, relevant literature, documents, and statistical data.

HEOS-2 observations of the boundary layer from the magnetopause to the ionosphere

International Nuclear Information System (INIS)

Formisano, V.

1980-01-01

HEOS-2 low energy electron data (10 eV - 3.7 keV) from the LPS Frascati plasma experiment have been used to identify three different magnetospheric electron populations. Magnetosheath-like electron energy spectra (35-50 eV) are characteristic of the plasma mantle, entry layer and cusps from the magnetopause down to 2-3 Rsub(E). Plasma sheet electrons (energy > 1 keV) are found at all local times, with strong intensities in the early morning quadrant and weaker intensities in the afternoon quadrant. The plasma sheet shows a well defined inner edge at all local times and latitudes, the inner edge coinciding probably with the plasmapause. The plasma sheet does not reach the magnetopause, but it is separated from it by a boundary layer electron population that is very distinct from the other two electron populations, most electrons having energies 100-300 eV. These three electron populations are mapped from the magnetopause down to the high latitude near earth regions. The boundary layer extends along the magnetopause up to 5-7 Rsub(E) above the equator; at higher latitudes it follows the magnetic lines of force and it is found closer and closer to the earth. (author)

Open Informational Ecosystems: The Missing Link for Sharing Educational Resources

Science.gov (United States)

Kerres, Michael; Heinen, Richard

2015-01-01

Open educational resources are not available "as such". Their provision relies on a technological infrastructure of related services that can be described as an informational ecosystem. A closed informational ecosystem keeps educational resources within its boundary. An open informational ecosystem relies on the concurrence of…

Superplasticity and grain boundary character distribution in overaged Al-Li-Cu-Mg-Zr alloy

International Nuclear Information System (INIS)

Avramovic-Cingara, G.; Aust, K.T.; Perovic, D.D.; McQueen, H.J.

1995-01-01

Samples of 8091 alloy were subjected to a thermomechanical processing (TMP) treatment that included the following stages: overaging before deformation, multistage deformation at 300 deg C and strain rate change tests for superplasticity. Torsional deformation was utilized both to develop the refined microstructure and to test for superplasticity. The strain rate sensitivity, m, of the material ranged between 0.30 and 0.45 at 450 deg C for strain rates between 8 x 10 -2 and 10 -3 s -1 . The grain boundary character distribution (GBCD) of thermomechanically processed Al-Li-Cu-Mg-Zr (8091) alloy, which develops good superplastic response, has been determined by an electron backscattering diffraction technique (EBSD). All grain boundaries have been classified into one of three categories in terms of Σ values : low angle, coincidence site lattice and random high angle boundaries. Quantitative studies of grain boundary character were done after various processing stages to obtain evidence about structure evolution and indicate an increase in Σ boundary frequency following TMP. Selected area electron diffraction examination (SAD) gave evidence about the refined structure, in which the grain boundary misorientation increased EBSD how the grain boundary character was changed to high Σ values. TEM analyses indicate that the T 2 phase is responsible for substructure stabilization. There is no evidence of cavity formation during superplastic deformation by torsion, which suggests that cavity nucleation is strongly influenced by the nature of stress. (author). 32 refs., 3 tabs., 9 figs

Electronic Human Resources Management (e-HRM Adoption Studies: Past and Future Research

Directory of Open Access Journals (Sweden)

Winarto Winarto

2018-05-01

Full Text Available Electronic human resource management (e-HRM systems become more widely used by profit and non-profit organization. However, the field currently lacks sound theoretical frameworks that can be useful in addressing a key issue concerning the implementation of e-HRM systems, in particular to obtain a better understanding of the factors influencing the adoption of e-HRM systems. The objective of this paper is to provide a foundation towards the development of a theoretical framework for the implementation of e-HRM systems and develop a conceptual model that would reflect the nature of e-HRM systems’ adoption through systematic literature review. Adopting Crossan and Apaydin’s procedure of systematic review, this paper investigated 21 empirical papers of electronics human resources management, then categorized them into 4 characteristics which influence the adoption; System and technology characteristics; Organizational characteristics; User/individual characteristics, and Environmental and contextual characteristics. Finally, the e-HRM adoption research framework is drawn and based on the framework; avenues for future research are discussed.   Bahasa Indonesia Abstrak: Manajemen sumber daya manusia elektronik (selanjutnya disebut dengan e-HRM semakin banyak digunakan oleh organisasi profit dan nonprofit. Namun, bidang dan topik ini belum memiliki kerangka teori yang mapan, yang dapat digunakan untuk menganalisis isu-isu terkait penerapan e-HRM, terutama mengenai faktor-faktor yang mempengaruhi adopsi sistem e-HRM. Tujuan penelitian ini adalah untuk memberikan landasan bagi pengembangan kerangka teoritis untuk implementasi sistem e-HRM dan mengembangkan model konseptual yang akan menggambarkan adopsi sistem e-HRM melalui tinjauan literatur sistematis. Mengadopsi prosedur dan metode Crossan dan Apaydin untuk melakukan telaah literatur secara sistematis, paper ini menyelidiki 21 publikasi empiris manajemen sumber daya manusia elektronik dari 2

Plasma Wind Tunnel Testing of Electron Transpiration Cooling Concept

Science.gov (United States)

2017-02-28

Colorado State University ETC Electron Transpiration Cooling LHTS Local Heat Transfer Simulation LTE Local Thermodynamic Equilibrium RCC Reinforced...ceramic electric material testing in plasma environment (not performed), 4. measurements and analysis of the Electron Transpiration Cooling (Sec. 4.2). 2...VKI 1D boundary layer code for computation of enthalpy and boundary layer parameters: a) iterate on ’virtually measured ’ heat flux, b) once enthalpy

Defining Boundaries between School and Work: Teachers and Students' Attribution of Quality to School-Based Vocational Training

Science.gov (United States)

Jonasson, Charlotte

2014-01-01

School-based vocational training has been organised to support students' boundary crossing between school and work. Such training has the potential to engage students in relevant work-oriented schooling. Drawing on theories of boundary connections and symbolic resources, it is argued that school participants define and attribute quality to…

Grain boundaries and defects in superconducting Bi-Sr-Ca-Cu-O ceramics

International Nuclear Information System (INIS)

Ramesh, R.; Bagley, B.G.; Tarascon, J.M.; Green, S.M.; Rudee, M.L.; Luo, H.L.

1990-01-01

Defects and structural interfaces in superconducting Bi-Sr-Ca-Cu-O have been characterized by transmission electron microscopy. The superconducting phase exhibits frequent variations in the stacking sequence (polytypoids). Dislocations, observed inside the grains, either introduce or accommodate the shear in the a-b plane and the local composition fluctuations. In general, the grains exhibit a platelike morphology with the a-b plane as the grain boundary plane. Grain boundaries along the short edge are generally disordered, whereas those near the long edge generally have a thin layer of the lower T c polytypoid. Coherent intragranular boundaries are also observed

Atmospheric stability in CFD &NDASH; Representation of the diurnal cycle in the atmospheric boundary layer

DEFF Research Database (Denmark)

Koblitz, Tilman; Bechmann, Andreas; Sogachev, Andrey

2012-01-01

For wind resource assessment, the wind industry is increasingly relying on Computational Fluid Dynamics (CFD) models that focus primarily on modeling the airflow in a neutrally stratified surface layer. So far, physical processes that are specific to the atmospheric boundary layer (ABL), for exam......For wind resource assessment, the wind industry is increasingly relying on Computational Fluid Dynamics (CFD) models that focus primarily on modeling the airflow in a neutrally stratified surface layer. So far, physical processes that are specific to the atmospheric boundary layer (ABL......), for example the Coriolis force, buoyancy forces and heat transport, are mostly ignored in state-of-the-art CFD models. In order to decrease the uncertainty of wind resource assessment, especially in complex terrain, the effect of thermal stratification on the ABL should be included in such models. The present...

Profiles of an initially perturbed electron beam

International Nuclear Information System (INIS)

Abdelsalam, F.W.

1991-01-01

This paper discusses the solutions for the profiles of an electron beam which is launched into a constant magnetic field with an initial boundary slope and injected with a radius which is greater or less than the cathode radius. It has been found that the outermost electron traces sine waves and executes limited excursions when the initial boundary slope corresponds to angles up to 1 degree, no matter whether the initial radius is 0.90 or 1.10 times the radius of the cathode. For initial inclination angles close to 2 degrees, the beam boundary does not preserve a sinusoidal shape, this statement holds true for focusing magnetic flux densities varying from 200x10 -4 to 700x10 -4 weber per square meter

Technology for Boundaries

DEFF Research Database (Denmark)

Bødker, Susanne; Kristensen, Jannie Friis; Nielsen, Christina

2003-01-01

.After analysing the history and the current boundary work, the paper will propose new technological support for boundary work. In particular the paper will suggest means of supporting boundaries when these are productive and for changing boundaries when this seems more appropriate. In total, flexible technologies......This paper presents a study of an organisation, which is undergoing a process transforming organisational and technological boundaries. In particular, we shall look at three kinds of boundaries: the work to maintain and change the boundary between the organisation and its customers; boundaries...... seem a core issue when dealing with technology for boundaries....

Improving Electronic Resources through Holistic Budgeting

Science.gov (United States)

Kusik, James P.; Vargas, Mark A.

2009-01-01

To establish a more direct link between its collections and the educational goals of Saint Xavier University, the Byrne Memorial Library has adopted a "holistic" approach to collection development. This article examines how traditional budget practices influenced the library's selection of resources and describes how holistic collection…

Model-based estimation with boundary side information or boundary regularization

International Nuclear Information System (INIS)

Chiao, P.C.; Rogers, W.L.; Fessler, J.A.; Clinthorne, N.H.; Hero, A.O.

1994-01-01

The authors have previously developed a model-based strategy for joint estimation of myocardial perfusion and boundaries using ECT (Emission Computed Tomography). The authors have also reported difficulties with boundary estimation in low contrast and low count rate situations. In this paper, the authors propose using boundary side information (obtainable from high resolution MRI and CT images) or boundary regularization to improve both perfusion and boundary estimation in these situations. To fuse boundary side information into the emission measurements, the authors formulate a joint log-likelihood function to include auxiliary boundary measurements as well as ECT projection measurements. In addition, the authors introduce registration parameters to align auxiliary boundary measurements with ECT measurements and jointly estimate these parameters with other parameters of interest from the composite measurements. In simulated PET O-15 water myocardial perfusion studies using a simplified model, the authors show that the joint estimation improves perfusion estimation performance and gives boundary alignment accuracy of <0.5 mm even at 0.2 million counts. The authors implement boundary regularization through formulating a penalized log-likelihood function. The authors also demonstrate in simulations that simultaneous regularization of the epicardial boundary and myocardial thickness gives comparable perfusion estimation accuracy with the use of boundary side information

MonitoringResources.org—Supporting coordinated and cost-effective natural resource monitoring across organizations

Science.gov (United States)

Bayer, Jennifer M.; Scully, Rebecca A.; Weltzin, Jake F.

2018-05-21

Natural resource managers who oversee the Nation’s resources require data to support informed decision-making at a variety of spatial and temporal scales that often cross typical jurisdictional boundaries such as states, agency regions, and watersheds. These data come from multiple agencies, programs, and sources, often with their own methods and standards for data collection and organization. Coordinating standards and methods is often prohibitively time-intensive and expensive. MonitoringResources.org offers a suite of tools and resources that support coordination of monitoring efforts, cost-effective planning, and sharing of knowledge among organizations. The website was developed by the Pacific Northwest Aquatic Monitoring Partnership—a collaboration of Federal, state, tribal, local, and private monitoring programs—and the U.S. Geological Survey (USGS), with funding from the Bonneville Power Administration and USGS. It is a key component of a coordinated monitoring and information network.

Clinician‐selected Electronic Information Resources do not Guarantee Accuracy in Answering Primary Care Physicians’ Information Needs. A review of: McKibbon, K. Ann, and Douglas B. Fridsma. “Effectiveness of Clinician‐selected Electronic Information Resources for Answering Primary Care Physicians’ Information Needs.” Journal of the American Medical Informatics Association 13.6 (2006: 653‐9.

Directory of Open Access Journals (Sweden)

Martha Ingrid Preddie

2008-03-01

Full Text Available Objective – To determine if electronic information resources selected by primary care physicians improve their ability to answer simulated clinical questions.Design – An observational study utilizing hour‐long interviews and think‐aloud protocols.Setting – The offices and clinics of primary care physicians in Canada and the United States.Subjects – Twenty‐five primary care physicians of whom 4 were women, 17 were from Canada, 22 were family physicians,and 24 were board certified.Methods – Participants provided responses to 23 multiple‐choice questions. Each physician then chose two questions and looked for the answers utilizing information resources of their own choice. The search processes, chosen resources and search times were noted. These were analyzed along with data on the accuracy of the answers and certainties related to the answer to each clinical question prior to the search.Main results – Twenty‐three physicians sought answers to 46 simulated clinical questions. Utilizing only electronic information resources, physicians spent a mean of 13.0 (SD 5.5 minutes searching for answers to the questions, an average of 7.3(SD 4.0 minutes for the first question and 5.8 (SD 2.2 minutes to answer the second question. On average, 1.8 resources were utilized per question. Resources that summarized information, such as the Cochrane Database of Systematic Reviews, UpToDate and Clinical Evidence, were favored 39.2% of the time, MEDLINE (Ovid and PubMed 35.7%, and Internet resources including Google 22.6%. Almost 50% of the search and retrieval strategies were keyword‐based, while MeSH, subheadings and limiting were used less frequently. On average, before searching physicians answered 10 of 23 (43.5% questions accurately. For questions that were searched using clinician‐selected electronic resources, 18 (39.1% of the 46 answers were accurate before searching, while 19 (42.1% were accurate after searching. The difference of

Estimation of grain boundary diffusivity in near-α titanium polycrystals

International Nuclear Information System (INIS)

Brockman, Robert A.; Pilchak, Adam L.; John Porter, W.; John, Reji

2011-01-01

The role of enhanced grain boundary diffusivity in high-temperature diffusion of interstitial elements through metals is widely recognized but poorly characterized in most materials. This paper summarizes an effort to estimate grain boundary diffusivity of oxygen in a near-α titanium alloy, Ti-6Al-2Sn-4Zr-2Mo-0.1Si, by explicitly incorporating microstructure obtained from electron backscatter diffraction into an analytical model. Attention is focused on near-surface diffusion behavior contributing to the rapid ingress of oxygen and possible crack initiation in high-temperature environments.

Low Energy Electrons in the Mars Plasma Environment

Science.gov (United States)

Link, Richard

2001-01-01

The ionosphere of Mars is rather poorly understood. The only direct measurements were performed by the Viking 1 and 2 landers in 1976, both of which carried a Retarding Potential Analyzer. The RPA was designed to measure ion properties during the descent, although electron fluxes were estimated from changes in the ion currents. Using these derived low-energy electron fluxes, Mantas and Hanson studied the photoelectron and the solar wind electron interactions with the atmosphere and ionosphere of Mars. Unanswered questions remain regarding the origin of the low-energy electron fluxes in the vicinity of the Mars plasma boundary. Crider, in an analysis of Mars Global Surveyor Magnetometer/Electron Reflectometer measurements, has attributed the formation of the magnetic pile-up boundary to electron impact ionization of exospheric neutral species by solar wind electrons. However, the role of photoelectrons escaping from the lower ionosphere was not determined. In the proposed work, we will examine the role of solar wind and ionospheric photoelectrons in producing ionization in the upper ionosphere of Mars. Low-energy (internal (photoelectron) sources of ionization, and accounts for Auger electron production. The code will be used to analyze Mars Global Surveyor measurements of solar wind and photoelectrons down to altitudes below 200 km in the Mars ionosphere, in order to determine the relative roles of solar wind and escaping photoelectrons in maintaining plasma densities in the region of the Mars plasma boundary.

Comparison of a simulated velocity profile of a turbulent boundary layer with measurements obtained by Femtosecond Laser Electronic Excitation Tagging (FLEET)

Science.gov (United States)

New-Tolley, Matthew; Zhang, Yibin; Shneider, Mikhail; Miles, Richard

2017-11-01

Accurate velocimetry measurements of turbulent flows are essential for improving our understanding of turbulent phenomena and validating numerical approaches. Femtosecond Laser Electronic Excitation Tagging (FLEET) is an unseeded molecular tagging method for velocimetry measurements in flows which contain nitrogen. A femtosecond laser pulse is used to ionize and dissociate nitrogen molecules within its focal zone. The decaying plasma fluoresces in the visible and infrared spectrum over a period of microseconds which allows the displacement of the tagged region to be photographed to determine velocity. This study compares the experimental and numerical advection of the tagged region in a turbulent boundary layer generated by a supersonic flow over a flat plate. The tagged region in the simulation is approximated as an infinitely thin cylinder while the flow field is generated using the steady state boundary layer equations with an algebraic turbulence model. This approximation is justified by previous computational analyses, using an unsteady three-dimensional Navier-Stokes solver, which indicate that the radial perturbations of the tagged region are negligible compared to its translation. This research was conducted with government support from the Air Force Office of Scientific Research under Dr. Ivett Leyva and the Army Research Office under Dr. Matthew Munson.

The Sound of Stigmatization: Sonic Habitus, Sonic Styles, and Boundary Work in an Urban Slum.

Science.gov (United States)

Schwarz, Ori

2015-07-01

Based on focus groups and interviews with student renters in an Israeli slum, the article explores the contributions of differences in sonic styles and sensibilities to boundary work, social categorization, and evaluation. Alongside visual cues such as broken windows, bad neighborhoods are characterized by sonic cues, such as shouts from windows. Students understand "being ghetto" as being loud in a particular way and use loudness as a central resource in their boundary work. Loudness is read as a performative index of class and ethnicity, and the performance of middle-class studentship entails being appalled by stigmatized sonic practices and participating in their exoticization. However, the sonic is not merely yet another resource of boundary work. Paying sociological attention to senses other than vision reveals complex interactions between structures anchored in the body, structures anchored in language, and actors' identification strategies, which may refine theorizations of the body and the senses in social theory.

Misorientation related microstructure at the grain boundary in a nickel-based single crystal superalloy

International Nuclear Information System (INIS)

Huang, Ming; Zhuo, Longchao; Liu, Zhanli; Lu, Xiaogang; Shi, Zhenxue; Li, Jiarong; Zhu, Jing

2015-01-01

The mechanical properties of nickel-based single crystal superalloys deteriorate with increasing misorientation, thus the finished product rate of the casting of single crystal turbine airfoils may be reduced due to the formation of grain boundaries especially when the misorientation angle exceeds to some extent. To this day, evolution of the microstructures at the grain boundaries with misorientation and the relationship between the microstructures and the mechanical properties are still unclear. In this work a detailed characterization of the misorientation related microstructure at the grain boundary in DD6 single crystal superalloy has been carried out using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques; the elemental distribution at the grain boundaries has been analyzed by energy dispersive (EDS) X-ray mapping; and the effect of precipitation of μ phases at the grain boundary on the mechanical property has been evaluated by finite element calculation. It is shown that the proportion of γ phase at the grain boundaries decreases, while the proportion of γ′ phase at the grain boundaries increases with increasing misorientation; the μ phase is precipitated at the grain boundaries when the misorientation angle exceeds about 10° and thus it could lead to a dramatic deterioration of the mechanical properties, as well as that the enrichment of Re and W gradually disappears as the misorientation angle increases. All these factors may result in the degradation of the mechanical properties at the grain boundaries as the misorientation increases. Furthermore, the finite element calculation confirms that precipitation of μ phases at the grain boundary is responsible for the significant deterioration of the mechanical properties when the misorientation exceeds about 10°. This work provides a physical imaging of the microstructure for understanding the relationship between the mechanical properties and the misorientation

Boundary issues

Science.gov (United States)

Townsend, Alan R.; Porder, Stephen

2011-03-01

the one for oceans. Encouragingly, while they argue that we've already crossed one key boundary in the P cycle, they also suggest it's not a Rubicon moment. The inefficiencies in P use that motivate these boundary debates are also clear targets for improvement, and some world regions may be on a trajectory towards greater P use efficiency (Vitousek et al 2009). This is a critical step for society, because even absent concerns over freshwater eutrophication or marine anoxic events, accelerating rates of P mining and inefficiencies in agricultural P use would still pose very real threats. There is legitimate debate over when readily accessible P reserves may run out (Cordell et al 2009, Van Kauenbergh 2010), but nobody argues with their finite nature. Sooner or later, we will be forced to keep P out of our waterways, if only because we will have to keep it on our farms. Without such a shift, we may face severe P constraints to food security within just a few human generations. As current P reserves decline, rising economic values of low concentration P stores may catalyze their harvest, but without considerable policy interventions, that price hike would exacerbate already strong global inequities in the distribution and use of chemical fertilizers (Sanchez and Swaminathan 2005). The harvest of low concentration P reserves would also create substantial collateral damage to the surrounding environment. Furthermore, even without exhaustion of high-concentration P reserves, their location in only a few countries creates geopolitical risks from the demand for an increasingly valuable resource (Cordell et al 2009). Policies aimed at lowering P inputs to aquatic environments will not only reduce the eutrophication risks explored by Carpenter and Bennett, they will increase P retention in agricultural landscapes and slow the decline of finite P reserves. Shifts in human diets can also make a profound difference in the amount of P (and N) required to meet caloric needs. Society

Review of material recovery from used electric and electronic equipment-alternative options for resource conservation.

Science.gov (United States)

Friege, Henning

2012-09-01

For waste from electric and electronic equipment, the WEEE Directive stipulates the separate collection of electric and electronic waste. As to new electric and electronic devices, the Restriction of Hazardous Substances (RoHS) Directive bans the use of certain chemicals dangerous for man and environment. From the implementation of the WEEE directive, many unsolved problems have been documented: poor collection success, emission of dangerous substances during collection and recycling, irretrievable loss of valuable metals among others. As to RoHS, data from the literature show a satisfying success. The problems identified in the process can be reduced to some basic dilemmas at the borders between waste management, product policy and chemical safety. The objectives of the WEEE Directive and the specific targets for use and recycling of appliances are not consistent. There is no focus on scarce resources. Extended producer responsibility is not sufficient to guarantee sustainable waste management. Waste management reaches its limits due to problems of implementation but also due to physical laws. A holistic approach is necessary looking at all branch points and sinks in the stream of used products and waste from electric and electronic equipment. This may be done with respect to the general rules for sustainable management of material streams covering the three dimensions of sustainable policy. The relationships between the players in the field of electric and electronic devices have to be taken into account. Most of the problems identified in the implementation process will not be solved by the current amendment of the WEEE Directive.

Charting a Course through CORAL: Texas A&M University Libraries' Experience Implementing an Open-Source Electronic Resources Management System

Science.gov (United States)

Hartnett, Eric; Beh, Eugenia; Resnick, Taryn; Ugaz, Ana; Tabacaru, Simona

2013-01-01

In 2010, after two previous unsuccessful attempts at electronic resources management system (ERMS) implementation, Texas A&M University (TAMU) Libraries set out once again to find an ERMS that would fit its needs. After surveying the field, TAMU Libraries selected the University of Notre Dame Hesburgh Libraries-developed, open-source ERMS,…

Models for Predicting Boundary Conditions in L-Mode Tokamak Plasma

International Nuclear Information System (INIS)

Siriwitpreecha, A.; Onjun, T.; Suwanna, S.; Poolyarat, N.; Picha, R.

2009-07-01

Full text: The models for predicting temperature and density of ions and electrons at boundary conditions in L-mode tokamak plasma are developed using an empirical approach and optimized against the experimental data obtained from the latest public version of the International Pedestal Database (version 3.2). It is assumed that the temperature and density at boundary of L-mode plasma are functions of engineering parameters such as plasma current, toroidal magnetic field, total heating power, line averaged density, hydrogenic particle mass (A H ), major radius, minor radius, and elongation at the separatrix. Multiple regression analysis is carried out for these parameters with 86 data points in L-mode from Aug (61) and JT60U (25). The RMSE of temperature and density at boundary of L-mode plasma are found to be 24.41% and 18.81%, respectively. These boundary models are implemented in BALDUR code, which will be used to simulate the L-mode plasma in the tokamak

Tuning the thermal conductivity of silicon carbide by twin boundary: a molecular dynamics study

International Nuclear Information System (INIS)

Liu, Qunfeng; Wang, Liang; Shen, Shengping; Luo, Hao

2017-01-01

Silicon carbide (SiC) is a semiconductor with excellent mechanical and physical properties. We study the thermal transport in SiC by using non-equilibrium molecular dynamics simulations. The work is focused on the effects of twin boundaries and temperature on the thermal conductivity of 3C-SiC. We find that compared to perfect SiC, twinned SiC has a markedly reduced thermal conductivity when the twin boundary spacing is less than 100 nm. The Si–Si twin boundary is more effective to phonon scattering than the C–C twin boundary. We also find that the phonon scattering effect of twin boundary decreases with increasing temperature. Our findings provide insights into the thermal management of SiC-based electronic devices and thermoelectric applications. (paper)

From boundaries to boundary work: middle managers creating inter-organizational change.

Science.gov (United States)

Oldenhof, Lieke; Stoopendaal, Annemiek; Putters, Kim

2016-11-21

Purpose In healthcare, organizational boundaries are often viewed as barriers to change. The purpose of this paper is to show how middle managers create inter-organizational change by doing boundary work: the dual act of redrawing boundaries and coordinating work in new ways. Design/methodology/approach Theoretically, the paper draws on the concept of boundary work from Science and Technology Studies. Empirically, the paper is based on an ethnographic investigation of middle managers that participate in a Dutch reform program across health, social care, and housing. Findings The findings show how middle managers create a sense of urgency for inter-organizational change by emphasizing "fragmented" service provision due to professional, sectoral, financial, and geographical boundaries. Rather than eradicating these boundaries, middle managers change the status quo gradually by redrawing composite boundaries. They use boundary objects and a boundary-transcending vocabulary emphasizing the need for societal gains that go beyond production targets of individual organizations. As a result, work is coordinated in new ways in neighborhood teams and professional expertise is being reconfigured. Research limitations/implications Since boundary workers create incremental change, it is necessary to follow their work for a longer period to assess whether boundary work contributes to paradigm change. Practical implications Organizations should pay attention to conditions for boundary work, such as legitimacy of boundary workers and the availability of boundary spaces that function as communities of practice. Originality/value By shifting the focus from boundaries to boundary work, this paper gives valuable insights into "how" boundaries are redrawn and embodied in objects and language.

Boundaries and e-health implementation in health and social care

Directory of Open Access Journals (Sweden)

King Gerry

2012-09-01

Full Text Available Abstract Background The major problem facing health and social care systems globally today is the growing challenge of an elderly population with complex health and social care needs. A longstanding challenge to the provision of high quality, effectively coordinated care for those with complex needs has been the historical separation of health and social care. Access to timely and accurate data about patients and their treatments has the potential to deliver better care at less cost. Methods To explore the way in which structural, professional and geographical boundaries have affected e-health implementation in health and social care, through an empirical study of the implementation of an electronic version of Single Shared Assessment (SSA in Scotland, using three retrospective, qualitative case studies in three different health board locations. Results Progress in effectively sharing electronic data had been slow and uneven. One cause was the presence of established structural boundaries, which lead to competing priorities, incompatible IT systems and infrastructure, and poor cooperation. A second cause was the presence of established professional boundaries, which affect staffs’ understanding and acceptance of data sharing and their information requirements. Geographical boundaries featured but less prominently and contrasting perspectives were found with regard to issues such as co-location of health and social care professionals. Conclusions To provide holistic care to those with complex health and social care needs, it is essential that we develop integrated approaches to care delivery. Successful integration needs practices such as good project management and governance, ensuring system interoperability, leadership, good training and support, together with clear efforts to improve working relations across professional boundaries and communication of a clear project vision. This study shows that while technological developments make

Study of the Sensitization on the Grain Boundary in Austenitic Stainless Steel Aisi 316

Directory of Open Access Journals (Sweden)

Kocsisová Edina

2014-12-01

Full Text Available Intergranular corrosion (IGC is one of the major problems in austenitic stainless steels. This type of corrosion is caused by precipitation of secondary phases on grain boundaries (GB. Precipitation of the secondary phases can lead to formation of chromium depleted zones in the vicinity of grain boundaries. Mount of the sensitization of material is characterized by the degree of sensitization (DOS. Austenitic stainless steel AISI 316 as experimental material had been chosen. The samples for the study of sensitization were solution annealed on 1100 °C for 60 min followed by water quenching and then sensitization by isothermal annealing on 700 °C and 650 °C with holding time from 15 to 600 min. Transmission electron microscopy (TEM was used for identification of secondary phases. Electron backscattered diffraction (EBSD was applied for characterization of grain boundary structure as one of the factors which influences on DOS.

Accelerated carrier recombination by grain boundary/edge defects in MBE grown transition metal dichalcogenides

Science.gov (United States)

Chen, Ke; Roy, Anupam; Rai, Amritesh; Movva, Hema C. P.; Meng, Xianghai; He, Feng; Banerjee, Sanjay K.; Wang, Yaguo

2018-05-01

Defect-carrier interaction in transition metal dichalcogenides (TMDs) plays important roles in carrier relaxation dynamics and carrier transport, which determines the performance of electronic devices. With femtosecond laser time-resolved spectroscopy, we investigated the effect of grain boundary/edge defects on the ultrafast dynamics of photoexcited carrier in molecular beam epitaxy (MBE)-grown MoTe2 and MoSe2. We found that, comparing with exfoliated samples, the carrier recombination rate in MBE-grown samples accelerates by about 50 times. We attribute this striking difference to the existence of abundant grain boundary/edge defects in MBE-grown samples, which can serve as effective recombination centers for the photoexcited carriers. We also observed coherent acoustic phonons in both exfoliated and MBE-grown MoTe2, indicating strong electron-phonon coupling in this materials. Our measured sound velocity agrees well with the previously reported result of theoretical calculation. Our findings provide a useful reference for the fundamental parameters: carrier lifetime and sound velocity and reveal the undiscovered carrier recombination effect of grain boundary/edge defects, both of which will facilitate the defect engineering in TMD materials for high speed opto-electronics.

Accelerated carrier recombination by grain boundary/edge defects in MBE grown transition metal dichalcogenides

Directory of Open Access Journals (Sweden)

Ke Chen

2018-05-01

Full Text Available Defect-carrier interaction in transition metal dichalcogenides (TMDs plays important roles in carrier relaxation dynamics and carrier transport, which determines the performance of electronic devices. With femtosecond laser time-resolved spectroscopy, we investigated the effect of grain boundary/edge defects on the ultrafast dynamics of photoexcited carrier in molecular beam epitaxy (MBE-grown MoTe2 and MoSe2. We found that, comparing with exfoliated samples, the carrier recombination rate in MBE-grown samples accelerates by about 50 times. We attribute this striking difference to the existence of abundant grain boundary/edge defects in MBE-grown samples, which can serve as effective recombination centers for the photoexcited carriers. We also observed coherent acoustic phonons in both exfoliated and MBE-grown MoTe2, indicating strong electron-phonon coupling in this materials. Our measured sound velocity agrees well with the previously reported result of theoretical calculation. Our findings provide a useful reference for the fundamental parameters: carrier lifetime and sound velocity and reveal the undiscovered carrier recombination effect of grain boundary/edge defects, both of which will facilitate the defect engineering in TMD materials for high speed opto-electronics.

Characterization of geostationary particle signatures based on the 'injection boundary' model

International Nuclear Information System (INIS)

Mauk, B.H.; Meng, C.

1983-01-01

To lend further support to the 'injection boundary' concept, this paper characterizes the details of geostationary particle signatures using a very simple-minded analysis procedure. The signatures are generated using the time of flight effects which evolve from an initial sharply defined, double-spiraled boundary configuration. By using only the most fundamental characteristics of standard convection configurations, the very complex and highly variable dispersion patterns frequently observed by geostationary satellites are successfully reproduced. In particular, seven distinctly different ion-electron paired dispersion patterns on energy versus time spectrograms (1 eV to 100 KeV) are predicted, and all seven of these are observed on a regular basis by both the SCATHA satellite (in the near geostationary orbit) and the ATS-6 satellite. Many of the details of the patterns have not been previously presented. It is concluded that most dynamical dispersion features (including energetic ion and electron echoes) can be mapped to the double-spiral boundary without further ad hoc assumptions. It is shown further that the predicted and observed dispersion patterns have symmetries which are distinct from the symmetries generally associated with the quasistationary particle convection patterns

Designing a model of electronic human resource management’s implementation at the Ministry of Communications and Information Technology

Directory of Open Access Journals (Sweden)

Mirali Seyednaghavi

2017-06-01

Full Text Available : In the first phase of this study a model for electronic human resource management in government agencies based on new public services was explored by using software MAXQDA, then in the second phase, relationship between the elements of the theory were tested using software Smart PLS2. So the aim of this study is to design a model of electronic human resource management’s implementation at the Ministry of Communications and Information Technology. In this regard, according to Strauss and Corbin’s structured plan, five hypotheses were tested. Quantitative data analysis indicates that the pressures of the policies and global perspectives cause to move toward e-HRM. Among the contextual conditions macro structural mechanisms, considerations of actors, governance considerations have a significant impact on the strategy of new public services and therefore lead to the consequences of its implementation in public organizations. The findings suggest that e-HRM does not have a positive and meaningful impact on new public services, and in our country, although the recent political developments have somehow removed the gap between public policy makers, administrators, and the public, but there is still a long way to go.

A statistical comparison of SuperDARN spectral width boundaries and DMSP particle precipitation boundaries in the morning sector ionosphere

Directory of Open Access Journals (Sweden)

G. Chisham

2005-03-01

Full Text Available Determining reliable proxies for the ionospheric signature of the open-closed field line boundary (OCB is crucial for making accurate ionospheric measurements of many magnetospheric processes (e.g. magnetic reconnection. This study compares the latitudes of Spectral Width Boundaries (SWBs, identified in the morning sector ionosphere using the Super Dual Auroral Radar Network (SuperDARN, with Particle Precipitation Boundaries (PPBs determined using the low-altitude Defense Meteorological Satellite Program (DMSP spacecraft, in order to determine whether the SWB represents a good proxy for the ionospheric projection of the OCB. The latitudes of SWBs and PPBs were identified using automated algorithms applied to 5 years (1997-2001 of data measured in the 00:00-12:00 Magnetic Local Time (MLT range. A latitudinal difference was measured between each PPB and the nearest SWB within a ±10min Universal Time (UT window and within a ±1h MLT window. The results show that the SWB represents a good proxy for the OCB close to midnight (~00:00-02:00 MLT and noon (~08:00-12:00 MLT, but is located some distance (~2°-4° equatorward of the OCB across much of the morning sector ionosphere (~02:00-08:00 MLT. On the basis of this and other studies we deduce that the SWB is correlated with the poleward boundary of auroral emissions in the Lyman-Birge-Hopfield ``Long" (LBHL UV emission range and hence, that spectral width is inversely correlated with the energy flux of precipitating electrons. We further conclude that the combination of two factors may explain the spatial distribution of spectral width values in the polar ionospheres. The small-scale structure of the convection electric field leads to an enhancement in spectral width in regions close to the OCB, whereas increases in ionospheric conductivity (relating to the level of incident electron energy flux lead to a reduction in spectral width in regions just equatorward of the OCB.

Grain boundary cavity growth under applied stress and internal pressure

International Nuclear Information System (INIS)

Mancuso, J.F.

1977-08-01

The growth of grain boundary cavities under applied stress and internal gas pressure was investigated. Methane gas filled cavities were produced by the C + 4H reversible CH4 reaction in the grain boundaries of type 270 nickel by hydrogen charging in an autoclave at 500 0 C with a hydrogen pressure of either 3.4 or 14.5 MPa. Intergranular fracture of nickel was achieved at a charging temperature of 300 0 C and 10.3 MPa hydrogen pressure. Cavities on the grain boundaries were observed in the scanning electron microscope after fracture. Photomicrographs of the cavities were produced in stereo pairs which were analyzed so as to correct for perspective distortion and also to determine the orientational dependence of cavity growth under an applied tensile stress

Cross-sectional measurement of grain boundary segregation using WDS

Energy Technology Data Exchange (ETDEWEB)

Christien, F., E-mail: frederic.christien@emse.fr [Laboratoire Georges Friedel, CNRS, Ecole des Mines de Saint-Etienne, 158 Cours Fauriel, 42023 Saint-Etienne (France); Risch, P. [Institut des Matériaux Jean Rouxel (IMN), CNRS, Université de Nantes, Rue Christian Pauc, 44306 Nantes (France)

2016-11-15

A new method is proposed for the quantification of grain boundary segregation using Wavelength Dispersive Spectroscopy (WDS) in a Scanning Electron Microscope (SEM). Analyses are undertaken on a simple metallographically polished section of material. The method is demonstrated for the model system of sulphur segregation to nickel grain boundaries. Quantification was carried out from sulphur concentration profiles acquired across 11 grain boundaries of a nickel specimen containing 5.4 wt ppm of sulphur in the bulk and equilibrated at 550 °C. The average sulphur grain boundary concentration determined is µ=35.2 ng cm{sup −2}=6.6×10{sup 14} atoms cm{sup −2}≈0.5 monolayer, which is in good agreement with a previous quantification obtained from SIMS (Secondary Ion Mass Spectrometry) on the same material. However this is lower by a factor of two than the quantification obtained using “surface” techniques on fractured specimens of the same material. With the conditions of analysis used in this study, the limit of detection of the method developed is found to be better than 10% of a sulphur monolayer. - Highlights: • Impurity grain boundary segregation can be measured using WDS in a SEM. • The method proposed is quantitative. • The specimen preparation is simple: metallographical section.

Boundaries of dreams, boundaries of dreamers: thin and thick boundaries as a new personality measure.

Science.gov (United States)

Hartmann, E

1989-11-01

Previous work by the author and his collaborators on frequent nightmare sufferers demonstrated that these people had striking personality characteristics which could be called "thin boundaries" in a number of different senses. In order to measure thin and thick boundaries, a 145-item questionnaire, the Boundary Questionnaire, has been developed which has now been taken by over 1,000 persons. Preliminary results are presented indicating that, as predicted a priori, several new groups of nightmare sufferers and groups of art students scored usually "thin," whereas a group of naval officers had usually "thick" boundaries. Overall, thinness on the Boundary Questionnaire correlated highly positively (r = .40) with frequency of dream recall and also significantly (r = .16) with length of sleep.

Cyclically induced softening due to low-angle boundary annihilation in a martensitic steel

International Nuclear Information System (INIS)

Sauzay, Maxime; Brillet, Helene; Monnet, Isabelle; Mottot, Michel; Barcelo, Francoise; Fournier, Benjamin; Pineau, Andre

2005-01-01

Martensitic steels are known for their softening during cyclic tests carried out at high temperature. The softening has been at least partially explained by lath and sub-grain boundary elimination. This article is dedicated to an attempt at modelling both phenomena. Thanks to mechanical tests it is shown that the softening is mainly due to a decrease of the backstress. Transmission electron microscopy allows us to propose a mechanism of low-angle boundary elimination. Annihilation between dislocations of low-angle boundaries and incident mobile dislocations is modelled. The macroscopic backstress is finally computed using a Hall-Petch law and the Taylor model

Climate change impacts on boundary and transboundary water management

Energy Technology Data Exchange (ETDEWEB)

Bruce, J.P.; Martin, H.; Colucci, P. [Global Change Strategies International, Ottawa, ON (Canada); McBean, G. [Institute for Catastrophic Loss Reduction, Toronto, ON (Canada); McDougall, J.; Shrubsole, D.; Whalley, J. [Western Ontario Univ., London, ON (Canada); Halliday, R. [R. Halliday and Associates, Saskatoon, SK (Canada); Alden, M.; Mortsch, L.; Mills, B. [Environment Canada, Downsview, ON (Canada). Meteorological Service of Canada; Coleman, C.; Zhang, Y.; Jia, J.; Porco, M.; Henstra, S.

2003-06-30

Climate change will have an impact on water cycles, with increased river flows in some areas, and decreased river flows in others. This report focuses on climate change related issues of water management in boundary and transboundary areas between Canada and the United States. Water resources in these areas are governed by agreements between provinces, territories and the federal governments of Canada and the United States. The Climate Change Action Fund and Natural Resources Canada launched a project through a partnership between the Global Change Strategies International (GCSI), the Institute for Catastrophic Loss Reduction (ICLR) and the Meteorological Services of Canada (MSC). The objective was to address potential difficulties in water management resources within North America. This report presents the results of the collaboration. It includes climate scenarios and climate model outputs on future temperature and precipitation by 2050, under a range of emission scenarios. It also includes an analysis of Canada-United States transboundary water instruments for vulnerability to climate change, as well as perceptions of fairness in allocating water in the Saskatchewan River Basin. This report also includes a review of the terms of existing Treaties and Agreements of 11 river basins between Canada and the United States on boundary and transboundary waters. The report concludes that it is very likely that much of Canada will see increased intense precipitation events while the interior regions will have increased risk of drought. These two projections will have major implications for river flows and the management of water resource. Seven recommendations were presented to ensure that water is allocated fairly and responsibly. refs., tabs., figs.

Modification of boundary fluctuations by LHCD in the HT-7 tokamak

International Nuclear Information System (INIS)

Song Mei; Wan Baonian; Xu Guosheng; Ling Bili

2003-01-01

Measurements of boundary fluctuations and fluctuation driven electron fluxes have been performed in ohmic and lower hybrid current drive enhanced confinement plasma using a graphite Langmuir probe array on HT-7 tokamak. The fluctuations are significantly suppressed and the turbulent fluxes are remarkably depressed in the enhanced plasma. We characterized the statistical properties of fluctuations and the particle flux and found a non-Gaussian character in the whole scrape-off layer with minimum deviations from Gaussian in the proximity of the velocity shear layer in ohmic plasma. In the enhanced plasma the deviations in the boundary region are all reduces obviously. The fluctuations and induced electron fluxes show sporadic bursts asymmetric in time and the asymmetry is remarkably weakened in the lower hybrid current driving (LHCD) phase. The results suggest a coupling between the statistical behaviour of fluctuations and the turbulent flow

The module of methodical support in system of electronic educational resources as the innovative element of the modern maintenance of formation

Directory of Open Access Journals (Sweden)

Ольга Николаевна Крылова

2009-06-01

Full Text Available The article introduces some results of research, which were devoted to evaluation of tearches' mobility to introduce innovations in the contents of education. The author considers innovative potential of modules of the methodical support for system of electronic educational resources.

Electron collision frequency variations and electric fields in the lower ionosphere

International Nuclear Information System (INIS)

Gokov, A.M.; Martynenko, S.I.

1997-01-01

Distribution of relative variations of the electron effective collision frequency at the ionosphere lower boundary is determined on the basis of analysis of radio-signals partially reflected from the lower ionosphere. Technique to evaluate the strength of electrical fields at the ionosphere lower boundary using experimentally measured variations of the effective frequency of electron collisions is elaborated. 12 refs., 2 figs

Atomic structure of surface defects in alumina studied by dynamic force microscopy: strain-relief-, translation- and reflection-related boundaries, including their junctions

International Nuclear Information System (INIS)

Simon, G H; König, T; Heinke, L; Lichtenstein, L; Heyde, M; Freund, H-J

2011-01-01

We present an extensive atomic resolution frequency modulation dynamic force microscopy study of ultrathin aluminium oxide on a single crystalline NiAl(110) surface. One-dimensional surface defects produced by domain boundaries have been resolved. Images are presented for reflection domain boundaries (RDBs), four different types of antiphase domain boundaries, a nucleation-related translation domain boundary and also domain boundary junctions. New structures and aspects of the boundaries and their network are revealed and merged into a comprehensive picture of the defect arrangements. The alumina film also covers the substrate completely at the boundaries and their junctions and follows the structural building principles found in its unit cell. This encompasses square and rectangular groups of surface oxygen sites. The observed structural elements can be related to the electronic signature of the boundaries and therefore to the electronic defects associated with the boundaries. A coincidence site lattice predicted for the RDBs is in good agreement with experimental data. With Σ = 19 it can be considered to be of low-sigma type, which frequently coincides with special boundary properties. Images of asymmetric RDBs show points of good contact alternating with regions of nearly amorphous disorder in the oxygen sublattice. (paper)

Introduction to electronic engineering I

International Nuclear Information System (INIS)

Kim, Bong Ryeol; Park, Han Gue; Lee, Tae Won; Choi, Gap Seok

1979-09-01

It deals with basic element of electronic engineering, which are an electric network such as alternating current voltage, distributed self, energy and power of an AC circuit, matrix, Tie-set and Cut-set, Fourier Transform and Laplace Transform, electromagnetics with vector theory, dot product and cross product, gradient, divergence static electricity, dielectric substance and capacity, boundary condition, resistance, magnetic field, magnetic circuit and electromagnetic field, electronic circuit including power circuit, amplification circuit, modulation and digital circuit, physical electronic engineering about movement of electron, semiconductor and integrated circuit.

Grain boundary migration induced segregation in V-Cr-Ti alloys

Energy Technology Data Exchange (ETDEWEB)

Gelles, D.S. [Pacific Northwest National Lab., Richland, WA (United States); Ohnuki, S.; Takahashi, H. [Univ. of Hokkaido (Japan)

1996-10-01

Analytical electron microscopy results are reported for a series of vanadium alloys irradiated in the HFIR JP23 experiment at 500{degrees}C. Alloys were V-5Cr-5Ti and pure vanadium which are expected to have transmuted to V-15Cr-5Ti and V-10Cr following irradiation. Analytical microscopy confirmed the expected transmutation occurred and showed redistribution of Cr and Ti resulting from grain boundary migration in V-5Cr-5Ti, but in pure V, segregation was reduced and no clear trends as a function of position near a boundary were identified.

Mapping travelling convection vortex events with respect to energetic particle boundaries

DEFF Research Database (Denmark)

Moretto, T.; Yahnin, A.

1998-01-01

Thirteen events of high-latitude ionospheric travelling convection vortices during very quiet conditions were identified in the Greenland magnetometer data during 1990 and 1991. The latitudes of the vortex centres for these events are compared to the energetic electron trapping boundaries...

Impact of Electronic Resources and Usage in Academic Libraries in Ghana: Evidence from Koforidua Polytechnic & All Nations University College, Ghana

Science.gov (United States)

Akussah, Maxwell; Asante, Edward; Adu-Sarkodee, Rosemary

2015-01-01

The study investigates the relationship between impact of electronic resources and its usage in academic libraries in Ghana: evidence from Koforidua Polytechnic & All Nations University College, Ghana. The study was a quantitative approach using questionnaire to gather data and information. A valid response rate of 58.5% was assumed. SPSS…

Microstructural analysis of the type-II boundary region in Alloy 152 weld

Energy Technology Data Exchange (ETDEWEB)

Yoo, Seung Chang; Choi, Kyoung Joon; Kim, Ji Hyun [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of)

2014-10-15

The weld metals are more susceptible to SCC growth and that most cracks are blunted by the fusion boundary. However, they also found that some cracking occurs along the fusion boundary, often in an area with high hardness. Nelson et al. investigated a DMW of Monel 409 stainless steel and American Iron and Steel Institute (AISI) 1080 alloy and found a type-II boundary, which exists parallel to the fusion boundary in the dilution zone. They conclude that the type-II boundary is a potential path for crack growth. While there are several theories for the mechanisms of the type-II boundary formation, they conclude that the type-II boundary forms from the allotropic δ-γ transformation at the base metal in the elevated austenitic temperature range. As the operation time of nuclear power plants using DMWs of Alloy 152 and A533 Gr. B increases, these DMWs must be evaluated for their resistance to SCC for long-term operations. However, only few studies have investigated the thermal aging effects induced by long-term operations at high temperature. Type-II boundary is known as a potential crack path from the results of crack growth test at DMW without any heat treatment. So the analysis about type-II boundary with applying heat treatment could be helpful to evaluate the susceptibility to SCC of structural materials. The objective of this study is to analyze the detailed microstructure of the type-II boundary region in the DMW of Alloy 152 and A533 Gr. B, after applying heat treatment simulating thermal aging effect of a nuclear power plant operation condition to evaluate the susceptibility of this region to SCC. The microstructure of the type-II boundary region in the DMW of Alloy 152 and A533 Gr. B were analyzed with an energy dispersive x-ray spectroscope attached to a scanning electron microscope (SEM-EDS), electron backscatter diffraction (EBSD), and a nanoindentation test. Microstructural, grain boundary orientation, nanohardness analysis were conducted in the type

Microstructural analysis of the type-II boundary region in Alloy 152 weld

International Nuclear Information System (INIS)

Yoo, Seung Chang; Choi, Kyoung Joon; Kim, Ji Hyun

2014-01-01

The weld metals are more susceptible to SCC growth and that most cracks are blunted by the fusion boundary. However, they also found that some cracking occurs along the fusion boundary, often in an area with high hardness. Nelson et al. investigated a DMW of Monel 409 stainless steel and American Iron and Steel Institute (AISI) 1080 alloy and found a type-II boundary, which exists parallel to the fusion boundary in the dilution zone. They conclude that the type-II boundary is a potential path for crack growth. While there are several theories for the mechanisms of the type-II boundary formation, they conclude that the type-II boundary forms from the allotropic δ-γ transformation at the base metal in the elevated austenitic temperature range. As the operation time of nuclear power plants using DMWs of Alloy 152 and A533 Gr. B increases, these DMWs must be evaluated for their resistance to SCC for long-term operations. However, only few studies have investigated the thermal aging effects induced by long-term operations at high temperature. Type-II boundary is known as a potential crack path from the results of crack growth test at DMW without any heat treatment. So the analysis about type-II boundary with applying heat treatment could be helpful to evaluate the susceptibility to SCC of structural materials. The objective of this study is to analyze the detailed microstructure of the type-II boundary region in the DMW of Alloy 152 and A533 Gr. B, after applying heat treatment simulating thermal aging effect of a nuclear power plant operation condition to evaluate the susceptibility of this region to SCC. The microstructure of the type-II boundary region in the DMW of Alloy 152 and A533 Gr. B were analyzed with an energy dispersive x-ray spectroscope attached to a scanning electron microscope (SEM-EDS), electron backscatter diffraction (EBSD), and a nanoindentation test. Microstructural, grain boundary orientation, nanohardness analysis were conducted in the type

SWAXS investigations on diffuse boundary nanostructures of metallic nanoparticles synthesized by electrical discharges

Energy Technology Data Exchange (ETDEWEB)

Guo, Xiaoai, E-mail: xiaoai.guo@kit.edu; Gutsche, Alexander; Nirschl, Hermann [Karlsruhe Institute of Technology, Institute for Mechanical Process Engineering and Mechanics (Germany)

2013-11-15

Metallic nanoparticles have attracted a particular interest in scientific research and industrial applications due to their unique size-dependent physical and chemical properties. An eco-friendly and cost-effective synthesis method called electrical discharge enables large scale production of metallic nanoparticles. Systematic investigations of such synthesized metallic nanoparticles help to optimize the synthesis process and improve the product quality. In this work, for the first time we have investigated the diffuse interfacial boundary nanostructures of the metallic nanoparticles, which were synthesized under different conditions by electrical glow and arc discharges in the carrier gas, by means of a small- and wide-angle X-ray scattering (SWAXS) technique using a laboratory X-ray source. Meanwhile, this unique SWAXS technique allows simultaneous study of the primary particle size, morphology, and crystallinity. The metallic nanoparticles (copper and nickel) under investigation cover a size range of 10–80 nm, and the determined thickness of the diffuse boundary nanostructured layer of metallic nanoparticles is in the range of 1–3 nm. The experimental results obtained by SWAXS were compared to the TEM/EDX observation and the XRD reference patterns from RRUFF database, and a good agreement was found. Our SWAXS investigations indicated that the existence of a diffuse nanostructured solid layer on the synthesized metallic nanoparticle surface causes a negative deviation of the scattering intensity (Ι∝q{sup -α}, α>4) from Porod’s law which corresponds to the case of ideal two-phase particle systems with sharp boundaries (Ι∝q{sup -α}, α=4) . This implies that the electron density profile is not sharp but changes gradually between two phases, and hence the exponent α is greater than four. Two electron density profile models, sigmoidal electron-density gradient model and linear electron-density gradient model, have been taken into account in

Slip transfer across grain boundaries in Fe-Si bicrystals

Czech Academy of Sciences Publication Activity Database

Gemperlová, Juliana; Polcarová, Milena; Gemperle, Antonín; Zárubová, Niva

2004-01-01

Roč. 378, - (2004), s. 97-101 ISSN 0925-8388 R&D Projects: GA ČR GA202/01/0670 Institutional research plan: CEZ:AV0Z1010914 Keywords : metals * dislocations and disclinations * bicrystals * grain boundaries * transmission electron microscopy * X-ray diffraction Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.562, year: 2004

Microstructure and composition of electromagnetically-characterized YBa2Cu3O7-δ grain boundaries

International Nuclear Information System (INIS)

Babcock, S.E.; Zhang, Na; Cai, Xue Yu; Larbalestier, D.C.; Gao, Yufei; Merkle, K.L.; Kaiser, D.L.

1991-01-01

The electrical character (flux-pinning, Josephson junction, or resistive) of the grain boundaries in approximately twenty flux-grown YBa 2 Cu 3 O 7-δ bicrystals was determined in previous studies. A selection of these same bicrystals now have been thinned for study by transmission and scanning transmission electron microscopy. High-spatial resolution imaging and analytical techniques reveal microstructural differences among these boundaries that are consistent with their diverse electrical characteristics. The observations offer preliminary insight into some of the feature that control the grain boundary superconducting properties and re-emphasize the very fine scale on which the grain boundary electrical character is determined. 11 refs., 6 figs

Exact and Optimal Quantum Mechanics/Molecular Mechanics Boundaries.

Science.gov (United States)

Sun, Qiming; Chan, Garnet Kin-Lic

2014-09-09

Motivated by recent work in density matrix embedding theory, we define exact link orbitals that capture all quantum mechanical (QM) effects across arbitrary quantum mechanics/molecular mechanics (QM/MM) boundaries. Exact link orbitals are rigorously defined from the full QM solution, and their number is equal to the number of orbitals in the primary QM region. Truncating the exact set yields a smaller set of link orbitals optimal with respect to reproducing the primary region density matrix. We use the optimal link orbitals to obtain insight into the limits of QM/MM boundary treatments. We further analyze the popular general hybrid orbital (GHO) QM/MM boundary across a test suite of molecules. We find that GHOs are often good proxies for the most important optimal link orbital, although there is little detailed correlation between the detailed GHO composition and optimal link orbital valence weights. The optimal theory shows that anions and cations cannot be described by a single link orbital. However, expanding to include the second most important optimal link orbital in the boundary recovers an accurate description. The second optimal link orbital takes the chemically intuitive form of a donor or acceptor orbital for charge redistribution, suggesting that optimal link orbitals can be used as interpretative tools for electron transfer. We further find that two optimal link orbitals are also sufficient for boundaries that cut across double bonds. Finally, we suggest how to construct "approximately" optimal link orbitals for practical QM/MM calculations.

Choice of futility boundaries for group sequential designs with two endpoints

Directory of Open Access Journals (Sweden)

Svenja Schüler

2017-08-01

Full Text Available Abstract Background In clinical trials, the opportunity for an early stop during an interim analysis (either for efficacy or for futility may relevantly save time and financial resources. This is especially important, if the planning assumptions required for power calculation are based on a low level of evidence. For example, when including two primary endpoints in the confirmatory analysis, the power of the trial depends on the effects of both endpoints and on their correlation. Assessing the feasibility of such a trial is therefore difficult, as the number of parameter assumptions to be correctly specified is large. For this reason, so-called ‘group sequential designs’ are of particular importance in this setting. Whereas the choice of adequate boundaries to stop a trial early for efficacy has been broadly discussed in the literature, the choice of optimal futility boundaries has not been investigated so far, although this may have serious consequences with respect to performance characteristics. Methods In this work, we propose a general method to construct ‘optimal’ futility boundaries according to predefined criteria. Further, we present three different group sequential designs for two endpoints applying these futility boundaries. Our methods are illustrated by a real clinical trial example and by Monte-Carlo simulations. Results By construction, the provided method of choosing futility boundaries maximizes the probability to correctly stop in case of small or opposite effects while limiting the power loss and the probability of stopping the study ‘wrongly’. Our results clearly demonstrate the benefit of using such ‘optimal’ futility boundaries, especially compared to futility boundaries commonly applied in practice. Conclusions As the properties of futility boundaries are often not considered in practice and unfavorably chosen futility boundaries may imply bad properties of the study design, we recommend assessing the

Electron plasma oscillations in the Venus foreshock

Science.gov (United States)

Crawford, G. K.; Strangeway, R. J.; Russell, C. T.

1990-01-01

Plasma waves are observed in the solar wind upstream of the Venus bow shock by the Pioneer Venus Orbiter. These wave signatures occur during periods when the interplanetary magnetic field through the spacecraft position intersects the bow shock, thereby placing the spacecraft in the foreshock region. The electron foreshock boundary is clearly evident in the data as a sharp onset in wave activity and a peak in intensity. Wave intensity is seen to drop rapidly with increasing penetration into the foreshock. The peak wave electric field strength at the electron foreshock boundary is found to be similar to terrestrial observations. A normalized wave spectrum was constructed using measurements of the electron plasma frequency and the spectrum was found to be centered about this value. These results, along with polarization studies showing the wave electric field to be field aligned, are consistent with the interpretation of the waves as electron plasma oscillations.

Electron plasma oscillations in the Venus foreshock

International Nuclear Information System (INIS)

Crawford, G.K.; Strangeway, R.J.; Russell, C.T.

1990-01-01

Plasma waves are observed in the solar wind upstream of the Venus bow shock by the Pioneer Venus Orbiter. These wave signatures occur during periods when the interplanetary magnetic field through the spacecraft position intersects the bow shock, thereby placing the spacecraft in the foreshock region. The electron foreshock boundary is clearly evident in the data as a sharp onset in wave activity and a peak in intensity. Wave intensity is seen to drop rapidly with increasing penetration into the foreshock. The peak wave electric field strength at the electron foreshock boundary is found to be similar to terrestrial observations. A normalized wave spectrum was constructed using measurements of the electron plasma frequency and the spectrum was found to be centered about this value. These results, along with polarization studies showing the wave electric field to be field aligned, are consistent with the interpretation of the waves as electron plasma oscillations

Utilization of Electronic Information Resources by Undergraduate Students of University of Ibadan: A Case Study of Social Sciences and Education

Science.gov (United States)

Owolabi, Sola; Idowu, Oluwafemi A.; Okocha, Foluke; Ogundare, Atinuke Omotayo

2016-01-01

The study evaluated utilization of electronic information resources by undergraduates in the Faculties of Education and the Social Sciences in University of Ibadan. The study adopted a descriptive survey design with a study population of 1872 undergraduates in the Faculties of Education and the Social Sciences in University of Ibadan, from which a…

Shaping the Electronic Library--The UW-Madison Approach.

Science.gov (United States)

Dean, Charles W., Ed.; Frazier, Ken; Pope, Nolan F.; Gorman, Peter C.; Dentinger, Sue; Boston, Jeanne; Phillips, Hugh; Daggett, Steven C.; Lundquist, Mitch; McClung, Mark; Riley, Curran; Allan, Craig; Waugh, David

1998-01-01

This special theme section describes the University of Wisconsin-Madison's experience building its Electronic Library. Highlights include integrating resources and services; the administrative framework; the public electronic library, including electronic publishing capability and access to World Wide Web-based and other electronic resources;…

Plasma performance, boundary studies and first experiments with ICRH in TEXTOR

International Nuclear Information System (INIS)

Waidmann, G.; Bay, H.L.; Bertschinger, G.

1985-01-01

The TEXTOR plasma serves as a test bed for plasma/wall interaction studies and ICRH experiments. Reproducible and long-lasting discharges with soft termination were generated in the internal disruptive mode. The operational regime for Ohmic heating is shown in a 1/q versus n-barsub(e)R/Bsub(T) diagram. A comparison of electrical conductivity derived from current density measurements with calculated values favours neoclassical theory. A pump limiter installed on TEXTOR demonstrated a particle removal rate of 6x10 20 particles per second out of the boundary layer. It could decrease the central electron density by 50%. The pump limiter was used to control fuelling and recycling characteristics of stable discharges. First experiments with additional ICRH showed a strong influence on the plasma boundary and scrape-off layer. The interaction of the radiofrequency with the boundary layer at present limits the power input to the plasma. Plasma boundary parameters have been measured by optical methods combined with neutral particle beams. (author)

The complex variable boundary element method: Applications in determining approximative boundaries

Science.gov (United States)

Hromadka, T.V.

1984-01-01

The complex variable boundary element method (CVBEM) is used to determine approximation functions for boundary value problems of the Laplace equation such as occurs in potential theory. By determining an approximative boundary upon which the CVBEM approximator matches the desired constant (level curves) boundary conditions, the CVBEM is found to provide the exact solution throughout the interior of the transformed problem domain. Thus, the acceptability of the CVBEM approximation is determined by the closeness-of-fit of the approximative boundary to the study problem boundary. ?? 1984.

Effects of thermal aging on the microstructure of Type-II boundaries in dissimilar metal weld joints

Science.gov (United States)

Yoo, Seung Chang; Choi, Kyoung Joon; Bahn, Chi Bum; Kim, Si Hoon; Kim, Ju Young; Kim, Ji Hyun

2015-04-01

In order to investigate the effects of long-term thermal aging on the microstructural evolution of Type-II boundary regions in the weld metal of Alloy 152, a representative dissimilar metal weld was fabricated from Alloy 690, Alloy 152, and A533 Gr.B. This mock-up was thermally aged at 450 °C to accelerate the effects of thermal aging in a nuclear power plant operation condition (320 °C). The microstructure of the Type-II boundary region of the weld root, which is parallel to and within 100 μm of the fusion boundary and known to be more susceptible to material degradation, was then characterized after different aging times using a scanning electron microscope equipped with an energy dispersive X-ray spectroscope for micro-compositional analysis, electron backscattered diffraction detector for grain and grain boundary orientation analysis, and a nanoindenter for measurement of mechanical properties. Through this, it was found that a steep compositional gradient and high grain average misorientation is created in the narrow zone between the Type-II and fusion boundaries, while the concentration of chromium and number of low-angle grain boundaries increases with aging time. A high average hardness was also observed in the same region of the dissimilar metal welds, with hardness peaking with thermal aging simulating an operational time of 15 years.

Grain-boundary microchemistry and intergranular cracking of irradiated austenitic stainless steels

International Nuclear Information System (INIS)

Chung, H.M.; Ruther, W.E.; Sanecki, J.E.; Kassner, T.F.

1993-01-01

Constant-extension-rate tensile tests and grain-boundary analysis by Auger electron spectroscopy were conducted on high and commercial-purity (HP and CP) Type 304 stainless steel (SS) specimens from irradiated boiling-water reactor (BWR) components to identify the mechanisms of irradiation-assisted stress corrosion cracking (IASCC). Contrary to previous beliefs, susceptibility to intergranular fracture could not be correlated with radiation-induced segregation of impurities such as Si, P, C, or S, but a correlation was obtained with grain-boundary Cr concentration, indicating a role for Cr depletion. Detailed analysis of grain-boundary chemistry was conducted on BWR neutron absorber tubes that were fabricated from two similar heats of HP Type 304 SS of virtually identical bulk chemical composition but exhibiting a significant difference in susceptibility to IASCC after irradiation to ∼2 x 10 21 n/cm 2 (E > 1 MeV). Grain-boundary concentrations of Cr Ni, Si, P, S, and C of the cracking-resistant and -susceptible HP heats were virtually identical. However, grain boundaries of the cracking-resistant material contained less N and more B and Li than those of the cracking-susceptible material. This observation indicates that, besides the deleterious effect of grain-boundary Cr depletion, a synergism between grain-boundary segregation of N and B and transmutation to H and Li plays an important role in IASCC

Mapping grain boundary heterogeneity at the nanoscale in a positive temperature coefficient of resistivity ceramic

Science.gov (United States)

Holsgrove, Kristina M.; Kepaptsoglou, Demie M.; Douglas, Alan M.; Ramasse, Quentin M.; Prestat, Eric; Haigh, Sarah J.; Ward, Michael B.; Kumar, Amit; Gregg, J. Marty; Arredondo, Miryam

2017-06-01

Despite being of wide commercial use in devices, the orders of magnitude increase in resistance that can be seen in some semiconducting BaTiO3-based ceramics, on heating through the Curie temperature (TC), is far from well understood. Current understanding of the behavior hinges on the role of grain boundary resistance that can be modified by polarization discontinuities which develop in the ferroelectric state. However, direct nanoscale resistance mapping to verify this model has rarely been attempted, and the potential approach to engineer polarization states at the grain boundaries, that could lead to optimized positive temperature coefficient (PTC) behavior, is strongly underdeveloped. Here we present direct visualization and nanoscale mapping in a commercially optimized BaTiO3-PbTiO3-CaTiO3 PTC ceramic using Kelvin probe force microscopy, which shows that, even in the low resistance ferroelectric state, the potential drop at grain boundaries is significantly greater than in grain interiors. Aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy reveal new evidence of Pb-rich grain boundaries symptomatic of a higher net polarization normal to the grain boundaries compared to the purer grain interiors. These results validate the critical link between optimized PTC performance and higher local polarization at grain boundaries in this specific ceramic system and suggest a novel route towards engineering devices where an interface layer of higher spontaneous polarization could lead to enhanced PTC functionality.

Mapping grain boundary heterogeneity at the nanoscale in a positive temperature coefficient of resistivity ceramic

Directory of Open Access Journals (Sweden)

Kristina M. Holsgrove

2017-06-01

Full Text Available Despite being of wide commercial use in devices, the orders of magnitude increase in resistance that can be seen in some semiconducting BaTiO3-based ceramics, on heating through the Curie temperature (TC, is far from well understood. Current understanding of the behavior hinges on the role of grain boundary resistance that can be modified by polarization discontinuities which develop in the ferroelectric state. However, direct nanoscale resistance mapping to verify this model has rarely been attempted, and the potential approach to engineer polarization states at the grain boundaries, that could lead to optimized positive temperature coefficient (PTC behavior, is strongly underdeveloped. Here we present direct visualization and nanoscale mapping in a commercially optimized BaTiO3–PbTiO3–CaTiO3 PTC ceramic using Kelvin probe force microscopy, which shows that, even in the low resistance ferroelectric state, the potential drop at grain boundaries is significantly greater than in grain interiors. Aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy reveal new evidence of Pb-rich grain boundaries symptomatic of a higher net polarization normal to the grain boundaries compared to the purer grain interiors. These results validate the critical link between optimized PTC performance and higher local polarization at grain boundaries in this specific ceramic system and suggest a novel route towards engineering devices where an interface layer of higher spontaneous polarization could lead to enhanced PTC functionality.

Transmission Electron Microscopy of a CMSX-4 Ni-Base Superalloy Produced by Selective Electron Beam Melting

Directory of Open Access Journals (Sweden)

Alireza B. Parsa

2016-10-01

Full Text Available In this work, the microstructures of superalloy specimens produced using selective electron beam melting additive manufacturing were characterized. The materials were produced using a CMSX-4 powder. Two selective electron beam melting processing strategies, which result in higher and lower effective cooling rates, are described. Orientation imaging microscopy, scanning transmission electron microscopy and conventional high resolution transmission electron microscopy are used to investigate the microstructures. Our results suggest that selective electron beam melting processing results in near equilibrium microstructures, as far as γ′ volume fractions, the formation of small amounts of TCP phases and the partitioning behavior of the alloy elements are concerned. As expected, higher cooling rates result in smaller dendrite spacings, which are two orders of magnitude smaller than observed during conventional single crystal casting. During processing, columnar grains grow in <100> directions, which are rotated with respect to each other. There are coarse γ/γ′ microstructures in high angle boundary regions. Dislocation networks form low angle boundaries. A striking feature of the as processed selective electron beam melting specimens is their high dislocation density. From a fundamental point of view, this opens new possibilities for the investigation of elementary dislocation processes which accompany solidification.

Controlling user access to electronic resources without password

Science.gov (United States)

Smith, Fred Hewitt

2017-08-22

Described herein are devices and techniques for remotely controlling user access to a restricted computer resource. The process includes obtaining an image from a communication device of a user. An individual and a landmark are identified within the image. Determinations are made that the individual is the user and that the landmark is a predetermined landmark. Access to a restricted computing resource is granted based on the determining that the individual is the user and that the landmark is the predetermined landmark. Other embodiments are disclosed.

The use of quality benchmarking in assessing web resources for the dermatology virtual branch library of the National electronic Library for Health (NeLH).

Science.gov (United States)

Kamel Boulos, M N; Roudsari, A V; Gordon, C; Muir Gray, J A

2001-01-01

In 1998, the U.K. National Health Service Information for Health Strategy proposed the implementation of a National electronic Library for Health to provide clinicians, healthcare managers and planners, patients and the public with easy, round the clock access to high quality, up-to-date electronic information on health and healthcare. The Virtual Branch Libraries are among the most important components of the National electronic Library for Health. They aim at creating online knowledge based communities, each concerned with some specific clinical and other health-related topics. This study is about the envisaged Dermatology Virtual Branch Libraries of the National electronic Library for Health. It aims at selecting suitable dermatology Web resources for inclusion in the forthcoming Virtual Branch Libraries after establishing preliminary quality benchmarking rules for this task. Psoriasis, being a common dermatological condition, has been chosen as a starting point. Because quality is a principal concern of the National electronic Library for Health, the study includes a review of the major quality benchmarking systems available today for assessing health-related Web sites. The methodology of developing a quality benchmarking system has been also reviewed. Aided by metasearch Web tools, candidate resources were hand-selected in light of the reviewed benchmarking systems and specific criteria set by the authors. Over 90 professional and patient-oriented Web resources on psoriasis and dermatology in general are suggested for inclusion in the forthcoming Dermatology Virtual Branch Libraries. The idea of an all-in knowledge-hallmarking instrument for the National electronic Library for Health is also proposed based on the reviewed quality benchmarking systems. Skilled, methodical, organized human reviewing, selection and filtering based on well-defined quality appraisal criteria seems likely to be the key ingredient in the envisaged National electronic Library for

Negotiating boundaries

DEFF Research Database (Denmark)

Aarhus, Rikke; Ballegaard, Stinne Aaløkke

2010-01-01

to maintain the order of the home when managing disease and adopting new healthcare technology. In our analysis we relate this boundary work to two continuums of visibility-invisibility and integration-segmentation in disease management. We explore five factors that affect the boundary work: objects......, activities, places, character of disease, and collaboration. Furthermore, the processes are explored of how boundary objects move between social worlds pushing and shaping boundaries. From this we discuss design implications for future healthcare technologies for the home.......To move treatment successfully from the hospital to that of technology assisted self-care at home, it is vital in the design of such technologies to understand the setting in which the health IT should be used. Based on qualitative studies we find that people engage in elaborate boundary work...

There is a Relationship between Resource Expenditures and Reference Transactions in Academic Libraries. A Review of: Dubnjakovic, A. (2012. Electronic resource expenditure and the decline in reference transaction statistics in academic libraries. Journal of Academic Librarianship, 38(2, 94-100. doi:10.1016/j.acalib.2012.01.001

Directory of Open Access Journals (Sweden)

Annie M. Hughes

2013-03-01

Full Text Available Objective – To provide an analysis of the impact of expenditures on electronic resourcesand gate counts on the increase or decrease in reference transactions.Design – Analysis of results of existing survey data from the National Center for Educational Statistics (NCES 2006 Academic Library Survey(ALS.Setting – Academic libraries in the United States.Subjects – 3925 academic library respondents.Methods – The author chose to use survey data collected from the 2006 ALS conducted bythe NCES. The survey included data on various topics related to academic libraries, but in the case of this study, the author chose to analyze three of the 193 variables included. The three variables: electronic books expenditure, computer hardware and software, and expenditures on bibliographic utilities, were combined into one variable called electronic resource expenditure. Gate counts were also considered as a variable. Electronic resource expenditure was also split as a variable into three groups: low, medium, and high. Multiple regression analysis and general linear modeling, along with tests of reliability, were employed. Main Results – The author determined that low, medium, and high spenders with regard to electronic resources exhibited differences in gate counts, and gate counts have an effect on reference transactions in any given week. Gate counts tend to not have much of an effect on reference transactions for the higher spenders, and higher spenders tend to have a higher number of reference transactions overall. Low spenders have lower gate counts and also a lower amount of reference transactions.Conclusion – The findings from this study show that academic libraries spending more on electronic resources also tend to have an increase with regard to reference transactions. The author also concludes that library spaces are no longer the determining factor with regard to number of reference transactions. Spending more on electronic resources is

Administrative Area Boundaries 2 (State Boundaries), Region 9, 2010, NAVTEQ

Data.gov (United States)

U.S. Environmental Protection Agency — NAVTEQ Administrative Area Boundaries 2 (State Boundaries) for Region 9. There are five Administrative Area Boundaries layers (1, 2, 3, 4, 5). These layers contain...

Administrative Area Boundaries 4 (City Boundaries), Region 9, 2010, NAVTEQ

Data.gov (United States)

U.S. Environmental Protection Agency — NAVTEQ Administrative Area Boundaries 4 (City Boundaries) for Region 9. There are five Administrative Area Boundaries layers (1, 2, 3, 4, 5). These layers contain...

Plasma boundaries at Mars: a 3-D simulation study

Directory of Open Access Journals (Sweden)

A. Bößwetter

2004-12-01

Full Text Available The interaction of the solar wind with the ionosphere of planet Mars is studied using a three-dimensional hybrid model. Mars has only a weak intrinsic magnetic field, and consequently its ionosphere is directly affected by the solar wind. The gyroradii of the solar wind protons are in the range of several hundred kilometers and therefore comparable with the characteristic scales of the interaction region. Different boundaries emerge from the interaction of the solar wind with the continuously produced ionospheric heavy-ion plasma, which could be identified as a bow shock (BS, ion composition boundary (ICB and magnetic pile up boundary (MPB, where the latter both turn out to coincide. The simulation results regarding the shape and position of these boundaries are in good agreement with the measurements made by Phobos-2 and MGS spacecraft. It is shown that the positions of these boundaries depend essentially on the ionospheric production rate, the solar wind ram pressure, and the often unconsidered electron temperature of the ionospheric heavy ion plasma. Other consequences are rays of planetary plasma in the tail and heavy ion plasma clouds, which are stripped off from the dayside ICB region by some instability.

Key words. Magnetospheric physics (solar wind interactions with unmagnetized bodies – Space plasma physics (discontinuities; numerical simulation studies

Reduced Need of Lubricity Additives in Soybean Oil Blends Under Boundary Lubrication Conditions

Science.gov (United States)

Converging prices of vegetable oils and petroleum, along with increased focus on renewable resources, gave more momentum to vegetable oil lubricants. Boundary lubrication properties of four Extreme Pressure (EP) additive blends in conventional Soy Bean Oil (SBO) and Paraffinic Mineral Oil (PMO) of ...

Electronic resources access and usage among the postgraduates of ...

African Journals Online (AJOL)

... and usage among the postgraduates of a Nigerian University of Technology. ... faced by postgraduates in using e-resources include takes too much time to find, ... Resources, Access, Use, Postgraduat, Students, University, Technology, Nigeria ... By Country · List All Titles · Free To Read Titles This Journal is Open Access.

Electron foreshock

International Nuclear Information System (INIS)

Klimas, A.J.

1985-01-01

ISEE particle and wave data are noted to furnish substantial support for the basic features of the velocity dispersed model at the foreshock boundary that was proposed by Filbert and Kellogg (1979). Among many remaining discrepancies between this model and observation, it is noted that unstable reduced velocity distributions have been discovered behind the thin boundary proposed by the model, and that these are at suprathermal energies lying far below those explainable in terms of an oscillating, two-stream instability. Although the long-theorized unstable beam of electrons has been found in the foreshock, there is still no ready explanation of the means by which it could have gotten there. 16 references

Determining market boundaries in the electricity sector

International Nuclear Information System (INIS)

Godde, Anne

2013-01-01

The purpose of the present study was to develop a method of determining market boundaries in preparation of identifying all the competitive forces which a company in the electricity sector must address and deciding on this basis whether it has a dominant position in the market. The study focused in particular on current developments in the German electricity sector, this being the only way to permit a demarcation that accurately reflects the true economic situation. First the question was addressed whether a determination of market boundaries is at all necessary for performing a competitive analysis and in what specific constellations they could play a role. Giving due consideration to the special features of the electricity sector the most preferable market demarcation methods were applied to individual areas of the electricity sector that are of competitive relevance. Efforts were directed at arriving at market boundaries most conducive to the goal of identifying those competitive forces which a company in the electricity sector must address. For this purpose a critical assessment was undertaken of established market demarcation practices in Europe and Germany in order to determine whether ''classical'' market demarcation methods could be applied or whether modifications were needed on account of special features of market structure. The author also describes and discusses alternatives to the established market demarcation methods. She also elucidates methods of determining the boundaries of markets that have emerged as a result of recent developments in the electricity sector, for example through the growth of electricity production from renewable resources, or which are still in the process of formation.

ERP as an organization innovation : Key users and cross-boundary knowledge management

NARCIS (Netherlands)

Maas, J.-B.; van Fenema, P.C.; Soeters, J.M.M.L.

2016-01-01

Purpose The purpose of this study is to provide more insight in the ways key users act as knowledge managers and boundary spanners during the enterprise resource planning (ERP) system usage phase. Despite the recognized importance of key users during the implementation phase of an ERP system, little

Region 7 Significant Ecological Resource Areas (ECO_RES.SIG_REGIONS)

Data.gov (United States)

U.S. Environmental Protection Agency — SIG_REGIONS is a boundary layer that displays Region 7's Significant Ecological Resource Areas. This layer represents large areas within which different ecosystem...

Conflict in the Currents: The Cross-boundary Consequences of Larval Dispersal

Science.gov (United States)

Rising, J. A.; Ramesh, N.; Dookie, D.

2016-02-01

As commercial fish populations decline in many regions, the increasing demand for ocean resources can create conflicts along international boundaries. Because fish stock ranges do not respect political boundaries, neighboring countries can impact each other through the management of the stocks within their exclusive economic zones. By combining spawning and larvae information from the FishBase database with current velocities from ocean reanalyses using a particle tracking scheme, we construct a measure of the cross-boundary diffusion of fish larvae for 40 major exploited species. These flows represent important connections both for fish populations and for fisheries and the people who depend on them, but these connections rely on fisheries management in the 'source' countries. We then use socioeconomic data on the national importance of these fish to identify hotspots for potential conflict. Finally, we consider how ranges will shift under climate change, and the social impacts of these shifts.

Boundary scan test of Belle II pixel detector electronics

Energy Technology Data Exchange (ETDEWEB)

Leitl, Philipp [Max-Planck-Institut fuer Physik (Werner-Heisenberg-Institut), Foehringer Ring 6, 80805 Muenchen (Germany)

2015-07-01

For the upgrade of the Vertex Detector at the Belle II experiment, DEPFET sensors will be used. These sensors need Application-Specific Integrated Circuits (ASICs) for control, readout and data processing. Because of high demands for a low material budget in the sensitive area, there is only little space left for these ASICs. Using state-of-the-art technologies like Ball Grid Array (BGA) chips, which are flip-chip mounted, the requirement of 14 ASICs on each of the 40 half ladders can be fulfilled. However, this highly integrated on-sensor ASIC solution results in a lack of physical access to the electrical connections, which is a problem for traditional testing methods. To overcome these limitations, the JTAG standard IEEE 1149.1 is used to check if the circuit is in working condition. This method provides electrical access to the boundary scan cells implemented in the ASICs. Therefore it is possible to perform connectivity tests and verify if the production of the circuit was successful.

Electronic Safety Resource Tools -- Supporting Hydrogen and Fuel Cell Commercialization

Energy Technology Data Exchange (ETDEWEB)

Barilo, Nick F.

2014-09-29

The Pacific Northwest National Laboratory (PNNL) Hydrogen Safety Program conducted a planning session in Los Angeles, CA on April 1, 2014 to consider what electronic safety tools would benefit the next phase of hydrogen and fuel cell commercialization. A diverse, 20-person team led by an experienced facilitator considered the question as it applied to the eight most relevant user groups. The results and subsequent evaluation activities revealed several possible resource tools that could greatly benefit users. The tool identified as having the greatest potential for impact is a hydrogen safety portal, which can be the central location for integrating and disseminating safety information (including most of the tools identified in this report). Such a tool can provide credible and reliable information from a trustworthy source. Other impactful tools identified include a codes and standards wizard to guide users through a series of questions relating to application and specific features of the requirements; a scenario-based virtual reality training for first responders; peer networking tools to bring users from focused groups together to discuss and collaborate on hydrogen safety issues; and a focused tool for training inspectors. Table ES.1 provides results of the planning session, including proposed new tools and changes to existing tools.

Electron backscatter diffraction: Strategies for reliable data acquisition and processing

International Nuclear Information System (INIS)

Randle, Valerie

2009-01-01

In electron backscatter diffraction (EBSD) software packages there are many user choices both in data acquisition and in data processing and display. In order to extract maximum scientific value from an inquiry, it is helpful to have some guidelines for best practice in conducting an EBSD investigation. The purpose of this article therefore is to address selected topics of EBSD practice, in a tutorial manner. The topics covered are a brief summary on the principles of EBSD, specimen preparation, calibration of an EBSD system, experiment design, speed of data acquisition, data clean-up, microstructure characterisation (including grain size) and grain boundary characterisation. This list is not meant to cover exhaustively all areas where EBSD is used, but rather to provide a resource consisting of some useful strategies for novice EBSD users.

Electron correlation in single-electron capture from helium by fast protons

International Nuclear Information System (INIS)

Purkait, M

2012-01-01

The differential and total cross sections for single charge exchange in p-He collisions have been calculated within the framework of four-body boundary corrected continuum intermediate state (BCCIS-4B) approximation. The effect of dynamic electron correlations is explicitly taken into account through the complete perturbation potentials.

Western Alaska ESI: SOCECON (Socioeconomic Resource Points and Lines)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains human-use resource data for airports, mining sites, area boundaries, and scenic rivers in Western Alaska. Vector points and lines in this data...

EFFECTIVE ELECTRONIC TUTORIAL

Directory of Open Access Journals (Sweden)

Andrei A. Fedoseev

2014-01-01

Full Text Available The article analyzes effective electronic tutorials creation and application based on the theory of pedagogy. Herewith the issues of necessary electronic tutorial functional, ways of the educational process organization with the use of information and communication technologies and the logistics of electronic educational resources are touched upon. 

Electron-inertia effects on driven magnetic field reconnection

International Nuclear Information System (INIS)

Al-Salti, N.; Shivamoggi, B.K.

2003-01-01

Electron-inertia effects on the magnetic field reconnection induced by perturbing the boundaries of a slab of plasma with a magnetic neutral surface inside are considered. Energetics of the tearing mode dynamics with electron inertia which controls the linearized collisionless magnetohydrodynamics (MHD) are considered with a view to clarify the role of the plasma pressure in this process. Cases with the boundaries perturbed at rates slow or fast compared with the hydromagnetic evolution rate are considered separately. When the boundaries are perturbed at a rate slow compared with the hydromagnetic evolution rate and fast compared with the resistive diffusion rate, the plasma response for early times is according to ideal MHD. A current sheet formation takes place at the magnetic neutral surface for large times in the ideal MHD stage and plasma becomes motionless. The subsequent evolution of the current sheet is found to be divided into two distinct stages: (i) the electron-inertia stage for small times (when the current sheet is very narrow); (ii) the resistive-diffusion stage for large times. The current sheet mainly undergoes exponential damping in the electron-inertia regime while the bulk of the diffusion happens in the resistivity regime. For large times of the resistive-diffusion stage when plasma flow is present, the current sheet completely disappears and the magnetic field reconnection takes place. When the boundaries are perturbed at a rate fast compared even with the hydromagnetic evolution rate, there is no time for the development of a current sheet and the magnetic field reconnection has been found not to take place

Effective Stress Law in Unconventional Reservoirs under Different Boundary Conditions

Science.gov (United States)

Saurabh, S.; Harpalani, S.

2017-12-01

Unconventional reservoirs have attracted a great deal of research interest worldwide during the past two decades. Low permeability and specialized techniques required to exploit these resources present opportunities for improvement in both production rates and ultimate recovery. Understanding subsurface stress modifications and permeability evolution are valuable when evaluating the prospects of unconventional reservoirs. These reservoir properties are functions of effective stress. As a part of this study, effective stress law, specifically the variation of anisotropic Biot's coefficient under various boundary conditions believed to exist in gas reservoirs by different researchers, has been established. Pressure-dependent-permeability (PdK) experiments were carried out on San Juan coal under different boundary conditions, that is, uniaxial strain condition and constant volume condition. Stress and strain in the vertical and horizontal directions were monitored throughout the experiment. Data collected during the experiments was used to determine the Biot's coefficient in vertical and horizontal directions under these two boundary conditions, treating coal as transversely isotropic. The variation of Biot's coefficient was found to be well correlated with the variation in coal permeability. Based on the estimated values of Biot's coefficients, a theory of variation in its value is presented for other boundary conditions. The findings of the study shed light on the inherent behavior of Biot's coefficient under different reservoir boundary conditions. This knowledge can improve the modeling work requiring estimation of effective stress in reservoirs, such as, pressure-/stress- dependent permeability. At the same time, if the effective stresses are known with more certainty by other methods, it enables assessment of the unknown reservoir boundary conditions.

Grain boundary segregation of antimony in .alfal-iron: prediction and experimental data

Czech Academy of Sciences Publication Activity Database

Lejček, Pavel

2004-01-01

Roč. 378, - (2004), s. 85-88 ISSN 0925-8388 Institutional research plan: CEZ:AV0Z1010914 Keywords : metals * grain boundaries * thermal analysis * electron emission spectroscopies Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.562, year: 2004

The nature of twin boundaries in the high-temperature superconductor YBa2Cu3O7-δ

International Nuclear Information System (INIS)

Zhu, Y.; Welch, D.O.

1999-01-01

Twin boundaries are the most commonly observed lattice defect in the high-temperature superconductor YBa 2 Cu 3 O 7-δ . Furthermore, the region around a twin boundary for which the structure and composition are seriously affected is of a scale comparable to the coherence length for the superconducting order parameter. Thus, twin boundaries can be important in the behavior of magnetic vortices and the critical current density in this material. In this paper the authors review the results of a wide range of investigations of twin boundary structure and composition by advanced transmission electron microscopy methods, both imaging and analytical in nature. A simple Landau model of twin boundary energy and width is proposed

Rivers as Political Boundaries: Peru and its Dynamic Borders

Science.gov (United States)

Abad, J. D.; Escobar, C.; Garcia, A. M. P.; Ortals, C.; Frias, C. E.; Vizcarra, J.

2014-12-01

Rivers, although inherently dynamic, have been chosen as political boundaries since the beginning of colonization for several reasons. Such divisions were chosen namely for their defensive capabilities and military benefits, and because they were often the first features mapped out by explorers. Furthermore, rivers were indisputable boundaries that did not require boundary pillars or people to guard them. However, it is important to understand the complexities of a river as a boundary. All rivers inevitably change over time through processes such as accretion, deposition, cut-off, or avulsion, rendering a political boundary subject to dispute. Depending upon the flow, size, and surrounding land, a river will migrate differently than others. As these natural features migrate one country loses land while another gains land leading to tension between legal rigidity and fluid dynamism. This in turn can manifest in social disruption due to cultural differences, political upheaval, or conflict risk as a result of scarce water resources. The purpose of this research is to assess the temporal and spatial variability of the political boundaries of Peru that follow rivers. Peru shares borders with Colombia, Brazil, Bolivia, Chile, and Ecuador. A large part of its northern border with Colombia follows the Putumayo River and later the Amazon River. Part of its eastern border with Brazil follows the Yavari River and later the Yaquirana River. These rivers are natural features used as political boundaries yet they differ in how each migrates. By means of a spatial and temporal analysis of satellite images it was possible to obtain erosion and deposition areas for the Putumayo River, the portion of the Amazon River that is part of the Peruvian boundary, the Yavari River, and the Yaquirana River. The erosion and deposition areas were related to land distribution among Peru, Colombia, and Brazil. By examining the Digital Elevation Model one can see how the altitude of the

Profiles of Wind and Turbulence in the Coastal Atmospheric Boundary Layer of Lake Erie

KAUST Repository

Wang, H; Barthelmie, R J; Crippa, P; Doubrawa, P; Pryor, S C

2014-01-01

Prediction of wind resource in coastal zones is difficult due to the complexity of flow in the coastal atmospheric boundary layer (CABL). A three week campaign was conducted over Lake Erie in May 2013 to investigate wind characteristics and improve

The role of remote engagement in supporting boundary chain networks across Alaska

Directory of Open Access Journals (Sweden)

Nathan P. Kettle

2015-01-01

Full Text Available Boundary organizations serve multiple roles in linking science and decision making, including brokering knowledge, supporting local- and cross-level networks, facilitating the co-production of knowledge, and negotiating conflict. Yet they face several challenges in providing services for an ever-increasing number of actors and institutions interested in climate information and adaptation. This study evaluates how the Alaska Center for Climate Assessment and Policy (ACCAP innovated its boundary spanning role to improve outcomes by partnering with other boundary organizations through its ongoing climate webinar series. We utilize the concept of boundary chains to investigate outcomes associated with different extended network connections. Our evaluation is based on the analysis three datasets, including interviews (2013 and two web-based questionnaires (2010 and 2013–2015. Findings from the evaluation reveal several ways that remote engagement via the ACCAP webinar series facilitates learning, decision application, and cross-level network building, and overcomes barriers associated with large geographic distances between communities. In an organic evolution and innovation of the climate webinar series, ACCAP partnered with other boundary organizations to establish satellite hub sites to facilitate in-person gatherings at remote locations, thereby increasing the number and diversity of participants served and supporting local networking within organizations, agencies, and communities. Leveraging complementary resources through the satellite hub sites provided mutual benefits for ACCAP and partnering boundary organizations. These findings advance our understanding of the value of remote engagement in supporting boundary spanning processes and how boundary organizations innovate their roles to build capacity and increase the usability of climate information.

Downshift of electron plasma oscillations in the electron foreshock region

International Nuclear Information System (INIS)

Fuselier, S.A.

1984-01-01

Electron plasma oscillations in the Earth's electron foreshock region are observed to shift above and below the local electron plasma frequency. As plasma oscillations shift from the plasma frequency, their bandwidth increases and their wavelength decreases. Observations of plasma oscillations well below the plasma frequency are correlated with times when ISEE-I is far downstream of the electron foreshock boundary. Although wavelengths of plasma oscillations below the plasma frequency satisfy klambda/sub De/ approx. = 1, the Doppler shift due to the motion of the solar wind is not sufficient to produce the observed frequency shifts. A beam-plasma interaction with beam velocities on the order of the electron thermal velocity is suggested as an explanation for plasma oscillations above and below the plasma frequency. Frequency, bandwidth, and wavelength changes predicted from the beam-plasma interaction are in good agreement with the observed characteristics of plasma oscillations in the foreshock region

Renewable energy resources

DEFF Research Database (Denmark)

Ellabban, Omar S.; Abu-Rub, Haitham A.; Blaabjerg, Frede

2014-01-01

Electric energy security is essential, yet the high cost and limited sources of fossil fuels, in addition to the need to reduce greenhouse gasses emission, have made renewable resources attractive in world energy-based economies. The potential for renewable energy resources is enormous because...... they can, in principle, exponentially exceed the world's energy demand; therefore, these types of resources will have a significant share in the future global energy portfolio, much of which is now concentrating on advancing their pool of renewable energy resources. Accordingly, this paper presents how...... renewable energy resources are currently being used, scientific developments to improve their use, their future prospects, and their deployment. Additionally, the paper represents the impact of power electronics and smart grid technologies that can enable the proportionate share of renewable energy...

Preference and Use of Electronic Information and Resources by Blind/Visually Impaired in NCR Libraries in India

Directory of Open Access Journals (Sweden)

Shailendra Kumar

2013-06-01

Full Text Available This paper aims to determine the preference and use of electronic information and resources by blind/visually impaired users in the leading National Capital Region (NCR libraries of India. Survey methodology has been used as the basic research tool for data collection with the help of questionnaires. The 125 in total users surveyed in all the five libraries were selected randomly on the basis of willingness of the users with experience of working in digital environments to participate in the survey. The survey results were tabulated and analyzed with descriptive statistics methods using Excel software and 'Stata version 11'. The findings reveal that ICT have a positive impact in the lives of people with disabilities as it helps them to work independently and increases the level of confidence among them. The Internet is the most preferred medium of access to information among the majority of blind/visually impaired users. The 'Complexity of content available on the net' is found as the major challenge faced during Internet use by blind users of NCR libraries. 'Audio books on CDs/DVDs and DAISY books' are the most preferred electronic resources among the majority of blind/visually impaired users. This study will help the library professionals and organizations/institutions serving people with disabilities to develop effective library services for blind/visually impaired users in the digital environment on the basis of findings on information usage behavior in the study.

Grain boundaries of nanocrystalline materials - their widths, compositions, and internal structures

International Nuclear Information System (INIS)

Fultz, B.; Frase, H.N.

2000-01-01

Nanocrystalline materials contain many atoms at and near grain boundaries. Sufficient numbers of Moessbauer probe atoms can be situated in grain boundary environments to make a clear contribution to the measured Moessbauer spectrum. Three types of measurements on nanocrystalline materials are reported here, all using Moessbauer spectrometry in conjunction with X-ray diffractometry, transmission electron microscopy, or small angle neutron scattering. By measuring the fraction of atoms contributing to the grain boundary component in a Moessbauer spectrum, and by knowing the grain size of the material, it is possible to deduce the average width of grain boundaries in metallic alloys. It is found that these widths are approximately 0.5 nm for fcc alloys and slightly larger than 1.0 nm for bcc alloys.Chemical segregation to grain boundaries can be measured by Moessbauer spectrometry, especially in conjunction with small angle neutron scattering. Such measurements on Fe-Cu and Fe 3 Si-Nb were used to study how nanocrystalline materials could be stabilized against grain growth by the segregation of Cu and Nb to grain boundaries. The segregation of Cu to grain boundaries did not stabilize the Fe-Cu alloys against grain growth, since the grain boundaries were found to widen and accept more Cu atoms during annealing. The Nb additions to Fe 3 Si did suppress grain growth, perhaps because of the low mobility of Nb atoms, but also perhaps because Nb atoms altered the chemical ordering in the alloy.The internal structure of grain boundaries in nanocrystalline materials prepared by high-energy ball milling is found to be unstable against internal relaxations at low temperatures. The Moessbauer spectra of the nanocrystalline samples showed changes in the hyperfine fields attributable to movements of grain boundary atoms. In conjunction with SANS measurements, the changes in grain boundary structure induced by cryogenic exposure and annealing at low temperature were found to be

Boundary-value problems with free boundaries for elliptic systems of equations

CERN Document Server

Monakhov, V N

1983-01-01

This book is concerned with certain classes of nonlinear problems for elliptic systems of partial differential equations: boundary-value problems with free boundaries. The first part has to do with the general theory of boundary-value problems for analytic functions and its applications to hydrodynamics. The second presents the theory of quasiconformal mappings, along with the theory of boundary-value problems for elliptic systems of equations and applications of it to problems in the mechanics of continuous media with free boundaries: problems in subsonic gas dynamics, filtration theory, and problems in elastico-plasticity.

Effects of dislocations on electron channeling

International Nuclear Information System (INIS)

George, Juby; Pathak, A P

2009-01-01

The phenomenon of electron channeling in a crystal affected by dislocations is considered. Earlier we had considered the quantum aspects of the positron channeling in a crystal bent by dislocations where the effects of longitudinal motion of the particle were also considered along with the transverse motion. In this paper, the effective potential for the electron case is found for the two regions of dislocation-affected channel. There is considerable shift in the potential minima due to dislocations. The frequency and the corresponding spectrum of the channeling radiation due to electrons channeling through the perfect channel and the two regions of dislocation-affected channels are calculated. The spectral distribution of radiation intensity changes with the parameters of dislocation. The continuity of wavefunctions and their derivatives is used at the three boundaries and the reflection and transmission coefficients are found using these boundary conditions in the same way as in the positron case.

Electron transport effects in ion induced electron emission

Energy Technology Data Exchange (ETDEWEB)

Dubus, A. [Universite Libre de Bruxelles, Service de Metrologie Nucleaire (CP 165/84), 50 av. FD Roosevelt, B-1050 Brussels (Belgium)]. E-mail: adubus@ulb.ac.be; Pauly, N. [Universite Libre de Bruxelles, Service de Metrologie Nucleaire (CP 165/84), 50 av. FD Roosevelt, B-1050 Brussels (Belgium); Roesler, M. [Karl-Pokern-Str. 12, D-12587 Berlin (Germany)

2007-03-15

Ion induced electron emission (IIEE) is usually described as a three-step process, i.e. electron excitation by the incident projectile, electron transport (and multiplication) and electron escape through the potential barrier at the surface. In many cases, the first step of the process has been carefully described. The second step of the process, i.e. electron transport and multiplication, has often been treated in a very rough way, a simple decreasing exponential law being sometimes used. It is precisely the aim of the present work to show the importance of a correct description of electron transport and multiplication in a theoretical calculation of IIEE. A short overview of the electron transport models developed for IIEE is given in this work. The so-called 'Infinite medium slowing-down model' often used in recent works is evaluated by means of Monte Carlo simulations. In particular, the importance of considering correctly the semi-infinite character of the medium and the boundary condition at the vacuum-medium interface is discussed. Quantities like the electron escape depth are also briefly discussed. This evaluation has been performed in the particular case of protons (25keV

Antiphase Boundaries in the Turbostratically Disordered Misfit Compound (BiSe)(1+δ)NbSe2.

Science.gov (United States)

Mitchson, Gavin; Falmbigl, Matthias; Ditto, Jeffrey; Johnson, David C

2015-11-02

(BiSe)(1+δ)NbSe2 ferecrystals were synthesized in order to determine whether structural modulation in BiSe layers, characterized by periodic antiphase boundaries and Bi-Bi bonding, occurs. Specular X-ray diffraction revealed the formation of the desired compound with a c-axis lattice parameter of 1.21 nm from precursors with a range of initial compositions and initial periodicities. In-plane X-ray diffraction scans could be indexed as hk0 reflections of the constituents, with a rectangular basal BiSe lattice and a trigonal basal NbSe2 lattice. Electron micrographs showed extensive turbostratic disorder in the samples and the presence of periodic antiphase boundaries (approximately 1.5 nm periodicity) in BiSe layers oriented with the [110] direction parallel to the zone axis of the microscope. This indicates that the structural modulation in the BiSe layers is not due to coherency strain resulting from commensurate in-plane lattices. Electrical transport measurements indicate that holes are the dominant charge carrying species, that there is a weak decrease in resistivity as temperature decreases, and that minimal charge transfer occurs from the BiSe to NbSe2 layers. This is consistent with the lack of charge transfer from the BiX to the TX2 layers reported in misfit layer compounds where antiphase boundaries were observed. This suggests that electronic considerations, i.e., localization of electrons in the Bi-Bi pairs at the antiphase boundaries, play a dominant role in stabilizing the structural modulation.

Model-based estimation with boundary side information or boundary regularization [cardiac emission CT].

Science.gov (United States)

Chiao, P C; Rogers, W L; Fessler, J A; Clinthorne, N H; Hero, A O

1994-01-01

The authors have previously developed a model-based strategy for joint estimation of myocardial perfusion and boundaries using ECT (emission computed tomography). They have also reported difficulties with boundary estimation in low contrast and low count rate situations. Here they propose using boundary side information (obtainable from high resolution MRI and CT images) or boundary regularization to improve both perfusion and boundary estimation in these situations. To fuse boundary side information into the emission measurements, the authors formulate a joint log-likelihood function to include auxiliary boundary measurements as well as ECT projection measurements. In addition, they introduce registration parameters to align auxiliary boundary measurements with ECT measurements and jointly estimate these parameters with other parameters of interest from the composite measurements. In simulated PET O-15 water myocardial perfusion studies using a simplified model, the authors show that the joint estimation improves perfusion estimation performance and gives boundary alignment accuracy of <0.5 mm even at 0.2 million counts. They implement boundary regularization through formulating a penalized log-likelihood function. They also demonstrate in simulations that simultaneous regularization of the epicardial boundary and myocardial thickness gives comparable perfusion estimation accuracy with the use of boundary side information.

Oscillations of the Outer Boundary of the Outer Radiation Belt During Sawtooth Oscillations

Directory of Open Access Journals (Sweden)

Jae-Hun Kim

2006-09-01

Full Text Available We report three sawtooth oscillation events observed at geosynchronous orbit where we find quasi-periodic (every 2-3 hours sudden flux increases followed by slow flux decreases at the energy levels of ˜50-400 keV. For these three sawtooth events, we have examined variations of the outer boundary of the outer radiation belt. In order to determine L values of the outer boundary, we have used data of relativistic electron flux observed by the SAMPEX satellite. We find that the outer boundary of the outer radiation belt oscillates periodically being consistent with sawtooth oscillation phases. Specifically, the outer boundary of the outer radiation belt expands (namely, the boundary L value increases following the sawtooth particle flux enhancement of each tooth, and then contracts (namely, the boundary L value decreases while the sawtooth flux decreases gradually until the next flux enhancement. On the other hand, it is repeatedly seen that the asymmetry of the magnetic field intensity between dayside and nightside decreases (increases due to the dipolarization (the stretching on the nightside as the sawtooth flux increases (decreases. This implies that the periodic magnetic field variations during the sawtooth oscillations are likely responsible for the expansion-contraction oscillations of the outer boundary of the outer radiation belt.

Pumping Electron-Positron Pairs from a Well Potential.

Science.gov (United States)

Wang, Qiang; Liu, Jie; Fu, Li-Bin

2016-04-29

In the presence of very deep well potential, electrons will spontaneously occupy the empty embedded bound states and electron-positron pairs are created by means of a non-perturbative tunneling process. In this work, by slowly oscillating the width or depth, the population transfer channels are opened and closed periodically. We find and clearly show that by the non-synchronous ejections of particles, the saturation of pair number in a static super-critical well can be broken, and electrons and positrons can be pumped inexhaustibly from vacuum with a constant production rate. In the adiabatic limit, final pair number after a single cycle has quantized values as a function of the upper boundary of the oscillating, and the critical upper boundaries indicate the diving points of the bound states.

Boundary Conditions of the High-Investment Human Resource Systems-Small-Firm Labor Productivity Relationship

Science.gov (United States)

Chadwick, Clint; Way, Sean A.; Kerr, Gerry; Thacker, James W.

2013-01-01

Although a few published, multiindustry, firm-level, empirical studies have linked systems of high-investment or high-performance human resource management practices to enhanced small-firm performance, this stream of strategic human resource management research is underdeveloped and equivocal. Accordingly, in this study, we use a sample of…

Toward a Conceptualization of Perceived Work-Family Fit and Balance: A Demands and Resources Approach

Science.gov (United States)

Voydanoff, Patricia

2005-01-01

Using person-environment fit theory, this article formulates a conceptual model that links work, family, and boundary-spanning demands and resources to work and family role performance and quality. Linking mechanisms include 2 dimensions of perceived work-family fit (work demands--family resources fit and family demands--work resources fit) and a…

Research and design of electron gun of electrocurtain

International Nuclear Information System (INIS)

Chen Pengfei; Zhang Mingchao; Li Xinmin; Wang Yuhong

1998-01-01

The characteristics of the electron beam current transport in the electron gun of the electrocurtain accelerator were studied and the origin of the influence on longitudinal uniformity of beam current was analysed. The deflection of the cathode is considered under the boundary condition of perfect constraint. Then a newly designed electron gun is introduced with longitudinal uniformity of current within +-10%

A statistical study of ionopause perturbation and associated boundary wave formation at Venus.

Science.gov (United States)

Chong, G. S.; Pope, S. A.; Walker, S. N.; Zhang, T.; Balikhin, M. A.

2017-12-01

In contrast to Earth, Venus does not possess an intrinsic magnetic field. Hence the interaction between solar wind and Venus is significantly different when compared to Earth, even though these two planets were once considered similar. Within the induced magnetosphere and ionosphere of Venus, previous studies have shown the existence of ionospheric boundary waves. These structures may play an important role in the atmospheric evolution of Venus. By using Venus Express data, the crossings of the ionopause boundary are determined based on the observations of photoelectrons during 2011. Pulses of dropouts in the electron energy spectrometer were observed in 92 events, which suggests potential perturbations of the boundary. Minimum variance analysis of the 1Hz magnetic field data for the perturbations is conducted and used to confirm the occurrence of the boundary waves. Statistical analysis shows that they were propagating mainly in the ±VSO-Y direction in the polar north terminator region. The generation mechanisms of boundary waves and their evolution into the potential nonlinear regime are discussed and analysed.

Low-latitude boundary layer near noon: An open field line model

Science.gov (United States)

Lyons, L. R.; Schulz, M.; Pridmore-Brown, D. C.; Roeder, J. L.

1994-01-01

We propose that many features of the cusp and low-latitude boundary layer (LLBL) observed near noon MLT can be explained by interpreting the LLBL as being on open lines with an inner boundary at the separatrix between open and closed magnetic field lines. This interpretation places the poleward boundary of the LLBL and equatorward boundary of the cusp along the field line that bifurcates at the cusp neutral point. The interpretation accounts for the abrupt boundary of magnetosheath particles at the inner edge of the LLBL, a feature that is inconsistent with LLBL formation by diffusion onto closed field lines, and for the distribution of magnetosheath particles appearing more as one continuous region than as two distinct regions across the noon cusp/LLBL boundary. Furthermore, we can explain the existence of energetic radiation belt electrons and protons with differing pitch angle distributions within the LLBL and their abrupt cutoff at the poleward boundary of the LLBL. By modeling the LLBL and cusp region quantitatively, we can account for a hemispherical difference in the location of the equatorial boundary of the cusp that is observed to be dependent on the dipole tilt angle but not on the interplanetary magnetic field (IMF) x component. We also find important variations and hemispherical differences in that the size of the LLBL that should depend strongly upon the x component of the IMF. This prediction is observationally testable. Finally, we find that when the IMF is strongly northward, the LLBL may include a narrow region adjacent to the magnetopause where field lines are detached (i.e., have both ends connected to the IMF).

Downshift of electron plasma oscillations in the electron foreshock region

International Nuclear Information System (INIS)

Fuselier, S.A.; Gurnett, D.A.; Fitzenreiter, R.J.; NASA, Goddard Space Flight Center, Greenbelt, MD)

1985-01-01

Electron plasma oscillations in the earth's electron foreshock region are observed to shift above and below the local electron plasma frequency. As plasma oscillations shift downward from the plasma frequency, their bandwidth increases and their wavelength decreases. Observations of plasma oscillations well below the plasma frequency are correlated with times when ISEE 1 is far downstream of the electron foreshock boundary. Although wavelengths of plasma oscillations below the plasma frequency satisfy k x lambda-De approximately 1 the Doppler shift due to the motion of the solar wind is not sufficient to produce the observed frequency shifts. A beam-plasma interaction with beam velocities on the order of the electron thermal velocity is suggested as an explanation for plasma oscillations above and below the plasma frequency. Frequency, bandwidth, and wavelength changes predicted from the beam-plasma interaction are in good agreement with the observed characteristics of plasma oscillations in the foreshock region. 28 references

Arbitrating a fiction: Canadian federalism and the Nova Scotia/Newfoundland and Labrador boundary dispute

Energy Technology Data Exchange (ETDEWEB)

Baier, G. [University of British Columbia, Dept. of Political Science, Vancouver, BC(Canada); Groarke, P.

2003-09-30

The dispute between the provinces of Nova Scotia and Newfoundland and Labrador, regarding ownership of natural resources to be found in the offshore area lying between the two provinces is discussed. Constitutionally, ownership of offshore natural resources belongs to the federal government. In this instance, the intention was to share control over development and revenues with the provinces through joint management accords, however, a dispute over offshore boundary arose, which eventually resulted in an arbitration tribunal. This paper analyzes the terms of reference for the tribunal and its findings, and concludes that the tribunal process was flawed. The authors cast doubts on the appropriateness of the tribunal's role, the method by which it reached its decision, and the legality of its findings. They conclude that the tribunal merely cloaks a political decision in legal garb since there are no genuine boundaries between the provinces, and the tribunal process simply apportioned federal resources between two provinces. The authors ultimately conclude that by resorting to the tribunal process the federal minister of natural resources was able to avoid political responsibility for making an unpopular decision by relying on a pseudo-judicial body for technical recommendations, and in so doing undermined the legitimacy of the Canadian federal system by obscuring the already murky lines of accountability of the federal and provincial governments. 57 end notes.

Modeling of the atomic and electronic structures of interfaces

International Nuclear Information System (INIS)

Sutton, A.P.

1988-01-01

Recent tight binding and Car-Parrinello simulations of grain boundaries in semiconductors are reviewed. A critique is given of some models of embrittlement that are based on electronic structure considerations. The structural unit model of grain boundary structure is critically assessed using some results for mixed tilt and twist grain boundaries. A new method of characterizing interfacial structure in terms of bond angle distribution functions is described. A new formulation of thermodynamic properties of interfaces is presented which focusses on the local atomic environment. Effective, temperature dependent N-body atomic interactions are derived for studying grain boundary structure at elevated temperature

Proof of existence of global solutions for m-component reaction-diffusion systems with mixed boundary conditions via the Lyapunov functional method

International Nuclear Information System (INIS)

Abdelmalek, Salem; Kouachi, Said

2007-01-01

To prove global existence for solutions of m-component reaction-diffusion systems presents fundamental difficulties in the case in which some components of the system satisfy Neumann boundary conditions while others satisfy nonhomogeneous Dirichlet boundary conditions and nonhomogeneous Robin boundary conditions. The purpose of this paper is to prove the existence of a global solution using a single inequality for the polynomial growth condition of the reaction terms. Our technique is based on the construction of polynomial functionals. This result generalizes those obtained recently by Kouachi et al (at press), Kouachi (2002 Electron. J. Diff. Eqns 2002 1), Kouachi (2001 Electron. J. Diff. Eqns 2001 1) and independently by Malham and Xin (1998 Commun. Math. Phys. 193 287)

Library usage patterns in the electronic information environment. Electronic journals, Use studies, Libraries, Medical libraries

Directory of Open Access Journals (Sweden)

B. Franklin

2004-01-01

Full Text Available This paper examines the methodology and results from Web-based surveys of more than 15,000 networked electronic services users in the United States between July 1998 and June 2003 at four academic health sciences libraries and two large main campus libraries serving a variety of disciplines. A statistically valid methodology for administering simultaneous Web-based and print-based surveys using the random moments sampling technique is discussed and implemented. Results from the Web-based surveys showed that at the four academic health sciences libraries, there were approximately four remote networked electronic services users for each in-house user. This ratio was even higher for faculty, staff, and research fellows at the academic health sciences libraries, where more than five remote users for each in-house user were recorded. At the two main libraries, there were approximately 1.3 remote users for each in-house user of electronic information. Sponsored research (grant funded research accounted for approximately 32% of the networked electronic services activity at the health sciences libraries and 16% at the main campus libraries. Sponsored researchers at the health sciences libraries appeared to use networked electronic services most intensively from on-campus, but not from in the library. The purpose of use for networked electronic resources by patrons within the library is different from the purpose of use of those resources by patrons using the resources remotely. The implications of these results on how librarians reach decisions about networked electronic resources and services are discussed.

Lung boundary detection in pediatric chest x-rays

Science.gov (United States)

Candemir, Sema; Antani, Sameer; Jaeger, Stefan; Browning, Renee; Thoma, George R.

2015-03-01

Tuberculosis (TB) is a major public health problem worldwide, and highly prevalent in developing countries. According to the World Health Organization (WHO), over 95% of TB deaths occur in low- and middle- income countries that often have under-resourced health care systems. In an effort to aid population screening in such resource challenged settings, the U.S. National Library of Medicine has developed a chest X-ray (CXR) screening system that provides a pre-decision on pulmonary abnormalities. When the system is presented with a digital CXR image from the Picture Archive and Communication Systems (PACS) or an imaging source, it automatically identifies the lung regions in the image, extracts image features, and classifies the image as normal or abnormal using trained machine-learning algorithms. The system has been trained on adult CXR images, and this article presents enhancements toward including pediatric CXR images. Our adult lung boundary detection algorithm is model-based. We note the lung shape differences during pediatric developmental stages, and adulthood, and propose building new lung models suitable for pediatric developmental stages. In this study, we quantify changes in lung shape from infancy to adulthood toward enhancing our lung segmentation algorithm. Our initial findings suggest pediatric age groupings of 0 - 23 months, 2 - 10 years, and 11 - 18 years. We present justification for our groupings. We report on the quality of boundary detection algorithm with the pediatric lung models.

Influence of incoherent twin boundaries on the electrical properties of β-Ga2O3 layers homoepitaxially grown by metal-organic vapor phase epitaxy

Science.gov (United States)

Fiedler, A.; Schewski, R.; Baldini, M.; Galazka, Z.; Wagner, G.; Albrecht, M.; Irmscher, K.

2017-10-01

We present a quantitative model that addresses the influence of incoherent twin boundaries on the electrical properties in β-Ga2O3. This model can explain the mobility collapse below a threshold electron concentration of 1 × 1018 cm-3 as well as partly the low doping efficiency in β-Ga2O3 layers grown homoepitaxially by metal-organic vapor phase epitaxy on (100) substrates of only slight off-orientation. A structural analysis by transmission electron microscopy (TEM) reveals a high density of twin lamellae in these layers. In contrast to the coherent twin boundaries parallel to the (100) plane, the lateral incoherent twin boundaries exhibit one dangling bond per unit cell that acts as an acceptor-like electron trap. Since the twin lamellae are thin, we consider the incoherent twin boundaries to be line defects with a density of 1011-1012 cm-2 as determined by TEM. We estimate the influence of the incoherent twin boundaries on the electrical transport properties by adapting Read's model of charged dislocations. Our calculations quantitatively confirm that the mobility reduction and collapse as well as partly the compensation are due to the presence of twin lamellae.

LGBQ-Specific Elderly Housing as a "Sparkling Sanctuary": Boundary Work on LGBQ Identity and Community in Relationship to Potential LGBQ-Specific Elderly Housing in Sweden.

Science.gov (United States)

Rosenberg, Lena; Kottorp, Anders; Johansson, Karin

2017-09-08

This study explored how boundaries in relationship to community and identity were created and negotiated among lesbian, gay, bisexual, and queer (LGBQ) people within the framework of picturing LGBQ-specific elderly housing as a housing alternative in older age, by applying focus group methodology. "An island as a sparkling sanctuary" was identified as a metaphor for how symbolic resources defining the LGBQ community can be manifested in LGBQ-specific qualities of elderly housing. The boundary work underlying this manifestation included elaborations on the dilemma between exclusiveness and normality. The findings illustrate further how symbolic resources and collective identities were developed through dialectic interplay between internal and external definitions. Further, the findings show how boundary work generated shared feelings of similarity and group membership. The associated symbolic and social resources not only served to deal with difficult situations but also to manifest LGBQ identity and sense of community as a "gold medal."

Brain response to prosodic boundary cues depends on boundary position

Directory of Open Access Journals (Sweden)

Julia eHolzgrefe

2013-07-01

Full Text Available Prosodic information is crucial for spoken language comprehension and especially for syntactic parsing, because prosodic cues guide the hearer’s syntactic analysis. The time course and mechanisms of this interplay of prosody and syntax are not yet well understood. In particular, there is an ongoing debate whether local prosodic cues are taken into account automatically or whether they are processed in relation to the global prosodic context in which they appear. The present study explores whether the perception of a prosodic boundary is affected by its position within an utterance. In an event-related potential (ERP study we tested if the brain response evoked by the prosodic boundary differs when the boundary occurs early in a list of three names connected by conjunctions (i.e., after the first name as compared to later in the utterance (i.e., after the second name. A closure positive shift (CPS — marking the processing of a prosodic phrase boundary — was elicited only for stimuli with a late boundary, but not for stimuli with an early boundary. This result is further evidence for an immediate integration of prosodic information into the parsing of an utterance. In addition, it shows that the processing of prosodic boundary cues depends on the previously processed information from the preceding prosodic context.

Electronic resources of the rare books and valuable editions department of the Central Scientific Library of the V.N. Karazin Kharkiv National University: open access for research

Directory of Open Access Journals (Sweden)

І. К. Журавльова

2014-12-01

Full Text Available The article describes tasks that electronic collections of rare books fulfill: broad access for readers to rare and valuable editions providing, preservation of ensuring of the original. On the example of the electronic collection of the Central Scientific Library of the V.N. Karazin Kharkiv National University – «eScriptorium: electronic archive of rare books and manuscripts for research and education» the possibility of the full-text resources of the valuable editions using is shown. The principles of creation, structure, chronological frameworks, directions of adding the documents to the archive are represented. The perspectives of the project development are outlined as well as examples of the digital libraries of the European countries and Ukraine are provided, the actual task of preserving the originals of the rare books of the country is raised, the innovative approaches to serving users with electronic resources are considered. The evidences of cooperation of the Central Scientific Library of the V.N. Karazin Kharkiv National University with the largest world digital libraries: World Digital Library and Europeana are provided.

Magnetic Field Generation, Particle Energization and Radiation at Relativistic Shear Boundary Layers

Science.gov (United States)

Liang, Edison; Fu, Wen; Spisak, Jake; Boettcher, Markus

2015-11-01

Recent large scale Particle-in-Cell (PIC) simulations have demonstrated that in unmagnetized relativistic shear flows, strong transverse d.c. magnetic fields are generated and sustained by ion-dominated currents on the opposite sides of the shear interface. Instead of dissipating the shear flow free energy via turbulence formation and mixing as it is usually found in MHD simulations, the kinetic results show that the relativistic boundary layer stabilizes itself via the formation of a robust vacuum gap supported by a strong magnetic field, which effectively separates the opposing shear flows, as in a maglev train. Our new PIC simulations have extended the runs to many tens of light crossing times of the simulation box. Both the vacuum gap and supporting magnetic field remain intact. The electrons are energized to reach energy equipartition with the ions, with 10% of the total energy in electromagnetic fields. The dominant radiation mechanism is similar to that of a wiggler, due to oscillating electron orbits around the boundary layer.

Multiscale Modeling of Grain Boundaries in ZrB2: Structure, Energetics, and Thermal Resistance

Science.gov (United States)

Lawson, John W.; Daw, Murray S.; Squire, Thomas H.; Bauschlicher, Charles W., Jr.

2012-01-01

A combination of ab initio, atomistic and finite element methods (FEM) were used to investigate the structures, energetics and lattice thermal conductance of grain boundaries for the ultra high temperature ceramic ZrB2. Atomic models of idealized boundaries were relaxed using density functional theory. Information about bonding across the interfaces was determined from the electron localization function. The Kapitza conductance of larger scale versions of the boundary models were computed using non-equilibrium molecular dynamics. The interfacial thermal parameters together with single crystal thermal conductivities were used as parameters in microstructural computations. FEM meshes were constructed on top of microstructural images. From these computations, the effective thermal conductivity of the polycrystalline structure was determined.

Microcrystalline silicon, grain boundaries and role of oxygen

Czech Academy of Sciences Publication Activity Database

Kočka, Jan; Stuchlíková, The-Ha; Ledinský, Martin; Stuchlík, Jiří; Mates, Tomáš; Fejfar, Antonín

2009-01-01

Roč. 93, č. 8 (2009), s. 1444-1447 ISSN 0927-0248 R&D Projects: GA MŠk(CZ) LC06040; GA AV ČR KAN400100701; GA ČR(CZ) GD202/05/H003; GA MŠk LC510; GA AV ČR IAA1010413 Institutional research plan: CEZ:AV0Z10100521 Keywords : microcrystalline silicon * grain boundaries * electronic transport * hydrogen * oxygen Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.858, year: 2009

Dynamical Processes in Open Quantum Systems from a TDDFT Perspective: Resonances and Electron Photoemission.

Science.gov (United States)

Larsen, Ask Hjorth; De Giovannini, Umberto; Rubio, Angel

2016-01-01

We present a review of different computational methods to describe time-dependent phenomena in open quantum systems and their extension to a density-functional framework. We focus the discussion on electron emission processes in atoms and molecules addressing excited-state lifetimes and dissipative processes. Initially we analyze the concept of an electronic resonance, a central concept in spectroscopy associated with a metastable state from which an electron eventually escapes (electronic lifetime). Resonances play a fundamental role in many time-dependent molecular phenomena but can be rationalized from a time-independent context in terms of scattering states. We introduce the method of complex scaling, which is used to capture resonant states as localized states in the spirit of usual bound-state methods, and work on its extension to static and time-dependent density-functional theory. In a time-dependent setting, complex scaling can be used to describe excitations in the continuum as well as wave packet dynamics leading to electron emission. This process can also be treated by using open boundary conditions which allow time-dependent simulations of emission processes without artificial reflections at the boundaries (i.e., borders of the simulation box). We compare in detail different schemes to implement open boundaries, namely transparent boundaries using Green functions, and absorbing boundaries in the form of complex absorbing potentials and mask functions. The last two are regularly used together with time-dependent density-functional theory to describe the electron emission dynamics of atoms and molecules. Finally, we discuss approaches to the calculation of energy and angle-resolved time-dependent pump-probe photoelectron spectroscopy of molecular systems.

Rigid supersymmetry with boundaries

Energy Technology Data Exchange (ETDEWEB)

Belyaev, D.V. [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Van Nieuwenhuizen, P. [State Univ. of New York, Stony Brook, NY (United States). C.N. Yang Inst. for Theoretical Physics

2008-01-15

We construct rigidly supersymmetric bulk-plus-boundary actions, both in x-space and in superspace. For each standard supersymmetric bulk action a minimal supersymmetric bulk-plus-boundary action follows from an extended F- or D-term formula. Additional separately supersymmetric boundary actions can be systematically constructed using co-dimension one multiplets (boundary superfields). We also discuss the orbit of boundary conditions which follow from the Euler-Lagrange variational principle. (orig.)

Effect of grain boundary segregation on mechanical properties of p-doped Fe-Si base alloys

Czech Academy of Sciences Publication Activity Database

Janovec, J.; Jenko, M.; Pokluda, J.; Vlach, B.; Lejček, Pavel; Svoboda, Milan; Šandera, P.

2005-01-01

Roč. 482, - (2005), s. 191-194 ISSN 0255-5476 R&D Projects: GA ČR(CZ) GA106/02/0253 Institutional research plan: CEZ:AV0Z1010914 Keywords : Fe-Si alloys * phosphorus grain boundary segregation * mechanical properties * Auger electron spectroscopy * transmission electron microscopy * mechanical testing Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.399, year: 2005

NATURAL RESOURCES ASSESSMENT

International Nuclear Information System (INIS)

D.F. Fenster

2000-01-01

The purpose of this report is to summarize the scientific work that was performed to evaluate and assess the occurrence and economic potential of natural resources within the geologic setting of the Yucca Mountain area. The extent of the regional areas of investigation for each commodity differs and those areas are described in more detail in the major subsections of this report. Natural resource assessments have focused on an area defined as the ''conceptual controlled area'' because of the requirements contained in the U.S. Nuclear Regulatory Commission Regulation, 10 CFR Part 60, to define long-term boundaries for potential radionuclide releases. New requirements (proposed 10 CFR Part 63 [Dyer 1999]) have obviated the need for defining such an area. However, for the purposes of this report, the area being discussed, in most cases, is the previously defined ''conceptual controlled area'', now renamed the ''natural resources site study area'' for this report (shown on Figure 1). Resource potential can be difficult to assess because it is dependent upon many factors, including economics (demand, supply, cost), the potential discovery of new uses for resources, or the potential discovery of synthetics to replace natural resource use. The evaluations summarized are based on present-day use and economic potential of the resources. The objective of this report is to summarize the existing reports and information for the Yucca Mountain area on: (1) Metallic mineral and mined energy resources (such as gold, silver, etc., including uranium); (2) Industrial rocks and minerals (such as sand, gravel, building stone, etc.); (3) Hydrocarbons (including oil, natural gas, tar sands, oil shales, and coal); and (4) Geothermal resources. Groundwater is present at the Yucca Mountain site at depths ranging from 500 to 750 m (about 1,600 to 2,500 ft) below the ground surface. Groundwater resources are not discussed in this report, but are planned to be included in the hydrology

Sulfur poisoning of a Ni(111) crystal with small angle boundaries (SAB) and its effect on CO adsorption

Energy Technology Data Exchange (ETDEWEB)

Sargent, G A; Lih-Ren Chao, J; Freeman, G B

1981-01-01

The sulfur poisoning of a Ni(111) crystal with small angle boundaries (SAB) and its effect on CO adsorption were studied using the techniques of low energy electron diffraction (LEED) and Auger electron spectroscopy (AES). The sulfur poisoned Ni(111)-SAB surface was prepared by heating the crystal to 850/sup 0/C for 20 min. The bulk sulfur impurity was diffused to the surface. The sulfur Auger peak intensities taken at and between boundary lines, show that sulfur distribution is uniform on the Ni(111)-SAB surface. No LEED pattern due to sulfur presence was observed. Sulfur atoms do not form an ordered structure in the Ni(111)-SAB surface. The Auger spectra showed that the boundary lines at the sulfur-free crystal surface provide favorable sites for the adsorbed CO to dissociate at temperatures as low as 25/sup 0/C. After sulfur is diffused to the surface, it blocks the active sites as well as the boundary sites. The boundary line enhanced dissociation of CO is no longer seen. Sulfur and nickel Auger intensities were taken during the CO adsorption. From the change of the intensities, sulfur only interacts with nickel and physically inhibits the CO adsorption and, thereby, further CO dissociation.

Metallicity at interphase boundaries due to polar catastrophe induced by charge density discontinuity

KAUST Repository

Albar, Arwa; Tahini, Hassan Ali; Schwingenschlö gl, Udo

2018-01-01

the electronic states at stoichiometric SnO/SnO2 (110) interphase boundaries. In this system, one would not expect polar catastrophe to have a role according to state-of-the-art theory because the interface lacks formal charge discontinuity. However, we observe

HREM investigation of the structure of the Σ5(310)/[001] symmetric tilt grain boundaries in Nb

International Nuclear Information System (INIS)

King, W.E.; Compbell, G.H.; Coombs, A.; Ruehle, M.

1991-01-01

This paper reports on atomistic simulations using interatomic potentials for Nb developed employing the embedded atom method (EAM) and the model generalized pseudopotential theory (MGPT) that have indicated a possible cusp at the Σ5 (310) orientation in the energy vs tilt angle curves for left-angle 001 right-angle symmetric tilt grain boundaries. In addition, the most stable structure predicted using EAM exhibits shifts of one crystal relative to the other along the tilt axis and along the direction perpendicular to the tilt axis lying in the boundary plane. The structure predicted using the MGPT was mirror symmetric across the plane of the grain boundary. This boundary has been prepared for experimental study using the ultra high vacuum diffusion bonding method. A segment of this boundary has been studied using high resolution electron microscopy

Defect and grain boundary scattering in tungsten: A combined theoretical and experimental study

Science.gov (United States)

Lanzillo, Nicholas A.; Dixit, Hemant; Milosevic, Erik; Niu, Chengyu; Carr, Adra V.; Oldiges, Phil; Raymond, Mark V.; Cho, Jin; Standaert, Theodorus E.; Kamineni, Vimal K.

2018-04-01

Several major electron scattering mechanisms in tungsten (W) are evaluated using a combination of first-principles density functional theory, a Non-Equilibrium Green's Function formalism, and thin film Kelvin 4-point sheet resistance measurements. The impact of grain boundary scattering is found to be roughly an order of magnitude larger than the impact of defect scattering. Ab initio simulations predict average grain boundary reflection coefficients for a number of twin grain boundaries to lie in the range r = 0.47 to r = 0.62, while experimental data can be fit to the empirical Mayadas-Schatzkes model with a comparable but slightly larger value of r = 0.69. The experimental and simulation data for grain boundary resistivity as a function of grain size show excellent agreement. These results provide crucial insights for understanding the impact of scaling of W-based contacts between active devices and back-end-of-line interconnects in next-generation semiconductor technology.

Electronic tracking of human resource skills and knowledge, just in time training, manageable due diligence

Energy Technology Data Exchange (ETDEWEB)

Kolodziej, M.A. [Quick Test International Inc., (Canada). Canadian Technology Human Resource Board; Baker, O. [KeySpan Energy Canada, Calgary, AB (Canada)

2001-06-01

KeySpan Energy Canada is in the process of obtaining recognition of various occupational profiles including pipeline operators, inspectors, and field and plant operators from various certifying organizations. The process of allowing individuals to obtain certification is recognized by Canadian Technology Human Resources Board as a step towards national standards for technologists and technicians. Proven competency is a must for workers in todays oil industry in response to increasingly stringent government safety regulations, environmental concerns and high public scrutiny. Quick Test international Inc. has developed a management tool in collaboration with end users at KeySpan Energy Canada. It is an electronic, Internet based competency tool for tracking personal competencies and maintaining continued competency. Response to the tool has been favourable. 2 refs., 4 figs.

Linking planetary boundaries and ecosystem accounting, with an illustration for the Colombian Orinoco river basin

NARCIS (Netherlands)

Vargas, Leonardo; Willemen, L.; Hein, Lars

2018-01-01

Economic development has increased pressures on natural resources during the last decades. The concept of planetary boundaries has been developed to propose limits on human activities based on earth processes and ecological thresholds. However, this concept was not developed to downscale planetary

Exploring the magnetospheric boundary layer

International Nuclear Information System (INIS)

Hapgood, M.A.; Bryant, D.A.

1992-01-01

We show how, for most crossings of the boundary layer, one can construct a 'transition parameter', based on electron density and temperature, which orders independent plasma measurements into well-defined patterns which are consistent from case to case. We conclude that there is a gradual change in the balance of processes which determine the structure of the layer and suggest that there is no advantage in dividing the layer into different regions. We further conclude that the mixing processes in layer act in an organised way to give the consistent patterns revealed by the transition parameter. More active processes must sometimes take to give the extreme values (e.g. in velocity) which are seen in some crossings

Influence of Al grain boundaries segregations and La-doping on embrittlement of intermetallic NiAl

Energy Technology Data Exchange (ETDEWEB)

Kovalev, Anatoly I., E-mail: a_kovalev@sprg.ru; Wainstein, Dmitry L.; Rashkovskiy, Alexander Yu.

2015-11-01

Highlights: • We investigated Al grain boundaries segregations in ordered pure and La-doped NiAl. • Structural segregation of Al decreases critical strain for brittle cracks nucleation. • La alloying sharply improves plasticity of NiAl intermetallic. • Metallicity of interatomic bonds on grain boundaries increases at La alloying. • We have experimentally measured by EELFS that La atoms are located in Al sublattice. - Abstract: The microscopic nature of intergranular fracture of NiAl was experimentally investigated by the set of electron spectroscopy techniques. The paper demonstrates that embrittlement of NiAl intermetallic compound is caused by ordering of atomic structure that leads to formation of structural aluminum segregations at grain boundaries (GB). Such segregations contain high number of brittle covalent interatomic bonds. The alloying by La increases the ductility of material avoiding Al GB enrichment and disordering GB atomic structure. The influence of La alloying on NiAl mechanical properties was investigated. GB chemical composition, atomic and electronic structure transformations after La doping were investigated by AES, XPS and EELFS techniques. To qualify the interatomic bonds metallicity the Fermi level (E{sub F}) position and electrons density (n{sub eff}) in conduction band were determined in both undoped and doped NiAl. Basing on experimental results the physical model of GB brittleness formation was proposed.

Grain boundary embrittlement and cohesion enhancement in copper

Energy Technology Data Exchange (ETDEWEB)

Paxton, Anthony; Lozovoi, Alexander [Atomistic Simulation Centre, Queen' s University Belfast, BT7 1NN (United Kingdom); Schweinfest, Rainer [Science+Computing ag, Hagellocher Weg 71-5, 720270 T ubingen (Germany); Finnis, Michael [Imperial College London, Exhibition Road, London SW7 2AZ (United Kingdom)

2008-07-01

There has been a long standing debate surrounding the mechanism of grain boundary embrittlement and cohesion enhancement in metals. Embrittlement can lead to catastrophic failure such as happened in the Hinkley Point disaster, or indeed in the case of the Titanic. This kind of embrittlement is caused by segregation of low solubility impurities to grain boundaries. While the accepted wisdom is that this is a phenomenon driven by electronic or chemical factors, using language such as charge transfer and electronegativity difference; we believe that in copper, at least, both cohesion enhancement and reduction are caused by a simple size effect. We have developed a theory that allows us to separate unambiguously, if not uniquely, chemical and structural factors. We have studied a large number of solutes in copper using first principles atomistic simulation to support this argument, and the results of these calculations are presented here.

Millisecond resolution electron fluxes from the Cluster satellites: Calibrated EDI ambient electron data

Science.gov (United States)

Förster, Matthias; Rashev, Mikhail; Haaland, Stein

2017-04-01

The Electron Drift Instrument (EDI) onboard Cluster can measure 500 eV and 1 keV electron fluxes with high time resolution during passive operation phases in its Ambient Electron (AE) mode. Data from this mode is available in the Cluster Science Archive since October 2004 with a cadence of 16 Hz in the normal mode or 128 Hz for burst mode telemetry intervals. The fluxes are recorded at pitch angles of 0, 90, and 180 degrees. This paper describes the calibration and validation of these measurements. The high resolution AE data allow precise temporal and spatial diagnostics of magnetospheric boundaries and will be used for case studies and statistical studies of low energy electron fluxes in the near-Earth space. We show examples of applications.

Electromagnetic microwaves in metal films with electron-phonon interaction and a dc magnetic field

DEFF Research Database (Denmark)

Hasselberg, L.E.

1976-01-01

A quantum-mechanical treatment of electromagnetic microwaves is performed for a metal film. The directions of the exterior ac and dc fields are taken to be arbitrary and boundary conditions for the electrons are assumed to be specular. The relation between the current and the electromagnetic field...... in the transmission spectrum can perhaps be obtained by assuming a finite Debye temperature and specular reflections of the electrons at the boundary surfaces. A sharp peak entirely caused by the finite electron-phonon interaction is also discussed....

On boundary superalgebras

International Nuclear Information System (INIS)

Doikou, Anastasia

2010-01-01

We examine the symmetry breaking of superalgebras due to the presence of appropriate integrable boundary conditions. We investigate the boundary breaking symmetry associated with both reflection algebras and twisted super-Yangians. We extract the generators of the resulting boundary symmetry as well as we provide explicit expressions of the associated Casimir operators.

Grain boundary structure and properties

International Nuclear Information System (INIS)

Balluffi, R.W.

1979-01-01

An attempt is made to distinguish those fundamental aspects of grain boundaries which should be relevant to the problem of the time dependent fracture of high temperature structural materials. These include the basic phenomena which are thought to be associated with cavitation and cracking at grain boundaries during service and with the more general microstructural changes which occur during both processing and service. A very brief discussion of the current state of our knowledge of these fundamentals is given. Included are the following: (1) structure of ideal perfect boundaries; (2) defect structure of grain boundaries; (3) diffusion at grain boundaries; (4) grain boundaries as sources/sinks for point defects; (5) grain boundary migration; (6) dislocation phenomena at grain boundaries; (7) atomic bonding and cohesion at grain boundaries; (8) non-equilibrium properties of grain boundaries; and (9) techniques for studying grain boundaries

The Biomedical Resource Ontology (BRO) to enable resource discovery in clinical and translational research.

Science.gov (United States)

Tenenbaum, Jessica D; Whetzel, Patricia L; Anderson, Kent; Borromeo, Charles D; Dinov, Ivo D; Gabriel, Davera; Kirschner, Beth; Mirel, Barbara; Morris, Tim; Noy, Natasha; Nyulas, Csongor; Rubenson, David; Saxman, Paul R; Singh, Harpreet; Whelan, Nancy; Wright, Zach; Athey, Brian D; Becich, Michael J; Ginsburg, Geoffrey S; Musen, Mark A; Smith, Kevin A; Tarantal, Alice F; Rubin, Daniel L; Lyster, Peter

2011-02-01

The biomedical research community relies on a diverse set of resources, both within their own institutions and at other research centers. In addition, an increasing number of shared electronic resources have been developed. Without effective means to locate and query these resources, it is challenging, if not impossible, for investigators to be aware of the myriad resources available, or to effectively perform resource discovery when the need arises. In this paper, we describe the development and use of the Biomedical Resource Ontology (BRO) to enable semantic annotation and discovery of biomedical resources. We also describe the Resource Discovery System (RDS) which is a federated, inter-institutional pilot project that uses the BRO to facilitate resource discovery on the Internet. Through the RDS framework and its associated Biositemaps infrastructure, the BRO facilitates semantic search and discovery of biomedical resources, breaking down barriers and streamlining scientific research that will improve human health. Copyright © 2010 Elsevier Inc. All rights reserved.

Emerging boundaries

DEFF Research Database (Denmark)

Løvschal, Mette

2014-01-01

of temporal and material variables have been applied as a means of exploring the processes leading to their socioconceptual anchorage. The outcome of this analysis is a series of interrelated, generative boundary principles, including boundaries as markers, articulations, process-related devices, and fixation...

Changing Boundaries

DEFF Research Database (Denmark)

Brodkin, Evelyn; Larsen, Flemming

2013-01-01

project that is altering the boundary between the democratic welfare state and the market economy. We see workfare policies as boundary-changing with potentially profound implications both for individuals disadvantaged by market arrangements and for societies seeking to grapple with the increasing...

Electronic Recruitment at CERN

CERN Multimedia

2004-01-01

The Human Resources Department switches to electronic recruitment. From now on whenever you are involved in a recruitment action you will receive an e-mail giving you access to a Web folder. Inside you will find a shortlist of applications drawn up by the Human Resources Department. This will allow you to consult the folder, at the same time as everyone else involved in the recruitment process, for the vacancy you are interested in. This new electronic recruitment system, known as e-RT, will be introduced in a presentation given at 10 a.m. on 11 February in the Main Auditorium. Implemented by AIS (Administrative Information Services) and the Human Resources Department, e-RT will cover vacancies open in all of CERN's recruitment programmes. The electronic application system was initially made available to technical students in July 2003. By December it was extended to summer students, fellows, associates and Local Staff. Geraldine Ballet from the Recruitment Service prefers e-RT to mountains of paper! The Hu...

Plastics disassembly versus bulk recycling: engineering design for end-of-life electronics resource recovery.

Science.gov (United States)

Rios, Pedro; Stuart, Julie Ann; Grant, Ed

2003-12-01

Annual plastic flows through the business and consumer electronics manufacturing supply chain include nearly 3 billion lb of high-value engineering plastics derived from petroleum. The recovery of resource value from this stream presents critical challenges in areas of materials identification and recycling process design that demand new green engineering technologies applied together with life cycle assessment and ecological supply chain analysis to create viable plastics-to-plastics supply cycles. The sustainable recovery of potentially high-value engineering plastics streams requires that recyclers either avoid mixing plastic parts or purify later by separating smaller plastic pieces created in volume reduction (shredding) steps. Identification and separation constitute significant barriers in the plastics-to-plastics recycling value proposition. In the present work, we develop a model that accepts randomly arriving electronic products to study scenarios by which a recycler might identify and separate high-value engineering plastics as well as metals. Using discrete eventsimulation,we compare current mixed plastics recovery with spectrochemical plastic resin identification and subsequent sorting. Our results show that limited disassembly with whole-part identification can produce substantial yields in separated streams of recovered engineering thermoplastics. We find that disassembly with identification does not constitute a bottleneck, but rather, with relatively few workers, can be configured to pull the process and thus decrease maximum staging space requirements.

Grain boundary microchemistry and metallurgical characterization of Eurofer'97 after simulated service conditions

International Nuclear Information System (INIS)

Fernandez, P.; Garcia-Mazario, M.; Lancha, A.M.; Lapena, J.

2004-01-01

The aim of this paper is to describe the microstructural investigations, the mechanical properties (hardness, tensile and charpy) and the grain boundary microchemistry studied by Auger electron spectroscopy (AES), of the Eurofer'97 steel aged in the range of temperatures from 400 to 600 deg. C up to 10,000 h. After these thermal aging treatments the steel showed a high microstructural stability, and similar values of hardness, ultimate tensile strength and 0.2% proof stress regardless of the material condition. A slight DBTT increase was observed in the material aged at 600 deg. C for 5000 and 10,000 h. The Auger results showed chromium enrichment at grain boundaries in all material conditions. In addition, phosphorus was detected at the grain boundaries after the aging treatments at 500 deg. C

Simulation of hypersonic rarefied flows with the immersed-boundary method

Science.gov (United States)

Bruno, D.; De Palma, P.; de Tullio, M. D.

2011-05-01

This paper provides a validation of an immersed boundary method for computing hypersonic rarefied gas flows. The method is based on the solution of the Navier-Stokes equation and is validated versus numerical results obtained by the DSMC approach. The Navier-Stokes solver employs a flexible local grid refinement technique and is implemented on parallel machines using a domain-decomposition approach. Thanks to the efficient grid generation process, based on the ray-tracing technique, and the use of the METIS software, it is possible to obtain the partitioned grids to be assigned to each processor with a minimal effort by the user. This allows one to by-pass the expensive (in terms of time and human resources) classical generation process of a body fitted grid. First-order slip-velocity boundary conditions are employed and tested for taking into account rarefied gas effects.

Power electronics substrate for direct substrate cooling

Science.gov (United States)

Le, Khiet [Mission Viejo, CA; Ward, Terence G [Redondo Beach, CA; Mann, Brooks S [Redondo Beach, CA; Yankoski, Edward P [Corona, CA; Smith, Gregory S [Woodland Hills, CA

2012-05-01

Systems and apparatus are provided for power electronics substrates adapted for direct substrate cooling. A power electronics substrate comprises a first surface configured to have electrical circuitry disposed thereon, a second surface, and a plurality of physical features on the second surface. The physical features are configured to promote a turbulent boundary layer in a coolant impinged upon the second surface.

Low-dose electron energy-loss spectroscopy using electron counting direct detectors.

Science.gov (United States)

Maigné, Alan; Wolf, Matthias

2018-03-01

Since the development of parallel electron energy loss spectroscopy (EELS), charge-coupled devices (CCDs) have been the default detectors for EELS. With the recent development of electron-counting direct-detection cameras, micrographs can be acquired under very low electron doses at significantly improved signal-to-noise ratio. In spectroscopy, in particular in combination with a monochromator, the signal can be extremely weak and the detection limit is principally defined by noise introduced by the detector. Here we report the use of an electron-counting direct-detection camera for EEL spectroscopy. We studied the oxygen K edge of amorphous ice and obtained a signal noise ratio up to 10 times higher than with a conventional CCD.We report the application of electron counting to record time-resolved EEL spectra of a biological protein embedded in amorphous ice, revealing chemical changes observed in situ while exposed by the electron beam. A change in the fine structure of nitrogen K and the carbon K edges were recorded during irradiation. A concentration of 3 at% nitrogen was detected with a total electron dose of only 1.7 e-/Å2, extending the boundaries of EELS signal detection at low electron doses.

Grain boundary effect of ZnO voltage sensitive ceramic

International Nuclear Information System (INIS)

Zhu Ziying; Lei Deming; Li Jingde

1991-01-01

Positron annihilation techenique has been to study the non-linear Ohmic effect of ZnO. The resemblence of curve representing the short life-time τ 1 and its component I 1 vs. current i with the voltage drop curve proves that this component I 1 belongs to the annihilation of transporting electron and positron. The experimental results give support to the explaination of Schottky barrier model for the effect of intergranular boundary

Collaboration in Healthcare Through Boundary Work and Boundary Objects

DEFF Research Database (Denmark)

Meier, Ninna

2015-01-01

This article contributes to our understanding of how boundary work is practiced in healthcare settings. Previous studies have shown how boundaries are constantly changing, multiple, and co-existing, and can also be relatively stable cognitive and social distinctions between individuals and groups...

The behavior of plasma with an arbitrary degree of degeneracy of electron gas in the conductive layer

Science.gov (United States)

Latyshev, A. V.; Gordeeva, N. M.

2017-09-01

We obtain an analytic solution of the boundary problem for the behavior (fluctuations) of an electron plasma with an arbitrary degree of degeneracy of the electron gas in the conductive layer in an external electric field. We use the kinetic Vlasov-Boltzmann equation with the Bhatnagar-Gross-Krook collision integral and the Maxwell equation for the electric field. We use the mirror boundary conditions for the reflections of electrons from the layer boundary. The boundary problem reduces to a one-dimensional problem with a single velocity. For this, we use the method of consecutive approximations, linearization of the equations with respect to the absolute distribution of the Fermi-Dirac electrons, and the conservation law for the number of particles. Separation of variables then helps reduce the problem equations to a characteristic system of equations. In the space of generalized functions, we find the eigensolutions of the initial system, which correspond to the continuous spectrum (Van Kampen mode). Solving the dispersion equation, we then find the eigensolutions corresponding to the adjoint and discrete spectra (Drude and Debye modes). We then construct the general solution of the boundary problem by decomposing it into the eigensolutions. The coefficients of the decomposition are given by the boundary conditions. This allows obtaining the decompositions of the distribution function and the electric field in explicit form.

A first-principles analysis of ballistic conductance, grain boundary scattering and vertical resistance in aluminum interconnects

Science.gov (United States)

Zhou, Tianji; Lanzillo, Nicholas A.; Bhosale, Prasad; Gall, Daniel; Quon, Roger

2018-05-01

We present an ab initio evaluation of electron scattering mechanisms in Al interconnects from a back-end-of-line (BEOL) perspective. We consider the ballistic conductance as a function of nanowire size, as well as the impact of surface oxidation on electron transport. We also consider several representative twin grain boundaries and calculate the specific resistivity and reflection coefficients for each case. Lastly, we calculate the vertical resistance across the Al/Ta(N)/Al and Cu/Ta(N)/Cu interfaces, which are representative of typical vertical interconnect structures with diffusion barriers. Despite a high ballistic conductance, the calculated specific resistivities at grain boundaries are 70-100% higher in Al than in Cu, and the vertical resistance across Ta(N) diffusion barriers are 60-100% larger for Al than for Cu. These results suggest that in addition to the well-known electromigration limitations in Al interconnects, electron scattering represents a major problem in achieving low interconnect line resistance at fine dimensions.

Optimal boundary control and boundary stabilization of hyperbolic systems

CERN Document Server

Gugat, Martin

2015-01-01

This brief considers recent results on optimal control and stabilization of systems governed by hyperbolic partial differential equations, specifically those in which the control action takes place at the boundary.  The wave equation is used as a typical example of a linear system, through which the author explores initial boundary value problems, concepts of exact controllability, optimal exact control, and boundary stabilization.  Nonlinear systems are also covered, with the Korteweg-de Vries and Burgers Equations serving as standard examples.  To keep the presentation as accessible as possible, the author uses the case of a system with a state that is defined on a finite space interval, so that there are only two boundary points where the system can be controlled.  Graduate and post-graduate students as well as researchers in the field will find this to be an accessible introduction to problems of optimal control and stabilization.

Merge of terminological resources

DEFF Research Database (Denmark)

Henriksen, Lina; Braasch, Anna

2012-01-01

In our globalized world, the amount of cross-national communication increases rapidly, which also calls for easy access to multi-lingual high quality terminological resources. Sharing of terminology resources is currently becoming common practice, and efficient strategies for integration...... – or merging – of terminology resources are strongly needed. This paper discusses prerequisites for successful merging with the focus on identification of candidate duplicates of a subject domain found in the resources to be merged, and it describes automatic merging strategies to be applied to such duplicates...... in electronic terminology resources. Further, some perspectives of manual, supplementary assessment methods supporting the automatic procedures are sketched. Our considerations are primarily based on experience gained in the IATE and EuroTermBank projects, as merging was a much discussed issue in both projects....

Electronic states of graphene nanoribbons and analytical solutions

Directory of Open Access Journals (Sweden)

Katsunori Wakabayashi, Ken-ichi Sasaki, Takeshi Nakanishi and Toshiaki Enoki

2010-01-01

Full Text Available Graphene is a one-atom-thick layer of graphite, where low-energy electronic states are described by the massless Dirac fermion. The orientation of the graphene edge determines the energy spectrum of π-electrons. For example, zigzag edges possess localized edge states with energies close to the Fermi level. In this review, we investigate nanoscale effects on the physical properties of graphene nanoribbons and clarify the role of edge boundaries. We also provide analytical solutions for electronic dispersion and the corresponding wavefunction in graphene nanoribbons with their detailed derivation using wave mechanics based on the tight-binding model. The energy band structures of armchair nanoribbons can be obtained by making the transverse wavenumber discrete, in accordance with the edge boundary condition, as in the case of carbon nanotubes. However, zigzag nanoribbons are not analogous to carbon nanotubes, because in zigzag nanoribbons the transverse wavenumber depends not only on the ribbon width but also on the longitudinal wavenumber. The quantization rule of electronic conductance as well as the magnetic instability of edge states due to the electron–electron interaction are briefly discussed.

Achieving conservation science that bridges the knowledge-action boundary.

Science.gov (United States)

Cook, Carly N; Mascia, Michael B; Schwartz, Mark W; Possingham, Hugh P; Fuller, Richard A

2013-08-01

There are many barriers to using science to inform conservation policy and practice. Conservation scientists wishing to produce management-relevant science must balance this goal with the imperative of demonstrating novelty and rigor in their science. Decision makers seeking to make evidence-based decisions must balance a desire for knowledge with the need to act despite uncertainty. Generating science that will effectively inform management decisions requires that the production of information (the components of knowledge) be salient (relevant and timely), credible (authoritative, believable, and trusted), and legitimate (developed via a process that considers the values and perspectives of all relevant actors) in the eyes of both researchers and decision makers. We perceive 3 key challenges for those hoping to generate conservation science that achieves all 3 of these information characteristics. First, scientific and management audiences can have contrasting perceptions about the salience of research. Second, the pursuit of scientific credibility can come at the cost of salience and legitimacy in the eyes of decision makers, and, third, different actors can have conflicting views about what constitutes legitimate information. We highlight 4 institutional frameworks that can facilitate science that will inform management: boundary organizations (environmental organizations that span the boundary between science and management), research scientists embedded in resource management agencies, formal links between decision makers and scientists at research-focused institutions, and training programs for conservation professionals. Although these are not the only approaches to generating boundary-spanning science, nor are they mutually exclusive, they provide mechanisms for promoting communication, translation, and mediation across the knowledge-action boundary. We believe that despite the challenges, conservation science should strive to be a boundary science, which

Complete electronics self-teaching guide with projects

CERN Document Server

Boysen, Earl

2012-01-01

An all-in-one resource on everything electronics-related! For almost 30 years, this book has been a classic text for electronics enthusiasts. Now completely updated for today's technology, this latest version combines concepts, self-tests, and hands-on projects to offer you a completely repackaged and revised resource. This unique self-teaching guide features easy-to-understand explanations that are presented in a user-friendly format to help you learn the essentials you need to work with electronic circuits. All you need is a general understanding of electronics concepts such as Oh

Electron energization in the geomagnetic tail current sheet

International Nuclear Information System (INIS)

Lyons, L.R.

1984-01-01

Electron motion in the distant tail current sheet is evaluated and found to violate the guiding center approximation at energies > or approx. =100 eV. Most electrons within the energy range approx.10 -1 -10 2 keV that enter the current sheet become trapped within the magnetic field reversal region. These electrons then convect earthward and gain energy from the cross-tail electric field. If the energy spectrum of electrons entering the current sheet is similar to that of electrons from the boundary layer surrounding the magnetotail, the energy gain from the electric field produces electron energy spectra comparable to those observed in the earth's plasma sheet. Thus current sheet interactions can be a significant source of particles and energy for plasma sheet electrons as well as for plasma sheet ions. A small fraction of electrons within the current sheet has its pitch angles scattered so as to be ejected from the current sheet within the atmospheric loss cone. These electrons can account for the electron precipitation near the high-latitude boundary of energetic electrons, which is approximately isotropic in pitch angle up to at least several hundred keV. Current sheet interaction should cause approximately isotropic auroral precipitation up to several hundred keV energies, which extends to significantly lower latitudes for ions than for electrons in agreement with low-altitude satellite observations. Electron precipitation associated with diffuse aurora generally has a transition at 1-10 keV to anisotropic pitch angle distributions. Such electron precipitation cannot be explained by current sheet interactions, but it can be explained by pitch angle diffusion driven by plasma turbulence

The analysis of bainitic ferrite microstructure in microalloyed plate steels through quantitative characterization of intervariant boundaries

Energy Technology Data Exchange (ETDEWEB)

Kang, Singon, E-mail: sikang@mines.edu [Advanced Steel Processing and Products Research Center, Colorado School of Mines, Golden, CO 80401 (United States); Speer, John G.; Regier, Ryan W. [Advanced Steel Processing and Products Research Center, Colorado School of Mines, Golden, CO 80401 (United States); Nako, Hidenori [Advanced Steel Processing and Products Research Center, Colorado School of Mines, Golden, CO 80401 (United States); Materials Research Laboratory, Kobe Steel Ltd., Kobe, Hyogo 651-2271 (Japan); Kennett, Shane C. [Advanced Steel Processing and Products Research Center, Colorado School of Mines, Golden, CO 80401 (United States); Exponent Failure Analysis Associates, Menlo Park, CA 94025 (United States); Findley, Kip O. [Advanced Steel Processing and Products Research Center, Colorado School of Mines, Golden, CO 80401 (United States)

2016-07-04

Electron backscatter diffraction (EBSD) measurements were performed to investigate the bainitic ferrite microstructure in low-carbon, microalloyed steels with varying C and Mn contents. Fully austenitized samples were isothermally heat treated at temperatures ranging from 450 to 550 °C to form bainitic ferrite. The bainitic ferrite microstructures and boundary characteristics obtained from the EBSD measurements were analyzed based on an inferred Kurdjumov-Sachs (K-S) orientation relationship. The heat treated samples exhibit a microstructure composed of laths and the lath aspect ratio tends to increase at lower isothermal heat treatment temperatures. High fractions of boundary misorientation angles below 5° are observed, which are due to lath boundaries in the microstructure. Additionally, misorientations of approximately 7°, 53° and 60° are observed, which are related to the sub-block, packet, and block boundaries, respectively. With decreasing isothermal heat treatment temperature, there is an increase of block boundaries; these boundaries are intervariant boundaries between different blocks within a packet, most of which have the misorientation angle of 60°. The specimens with a higher carbon level contained increased length of block boundaries, whereas the addition of Mn moderated the dependence of block boundary length on the heat treatment temperature within the experimental temperature range. Meanwhile, the length of intervariant boundaries of both packet and sub-block character did not vary much with heat treatment temperature and alloy composition.

Experimental approaches for probing interfaces and grain boundaries

International Nuclear Information System (INIS)

Barrera, E.V.; Marcus, H.L.

1990-01-01

This paper focuses its attention on several research efforts performed by the authors and colleagues whose primary aim is probing interfacial and grain boundary properties. The first investigations described pertain to impurity segregation induced embrittlement which were modeled using thermodynamic considerations and were characterized by fracture testing using Auger electron spectroscopy (AES). Localized interface chemical characterization is essential in this research. The second investigation focuses on interface/impurity interaction determination. Extended X-Ray Absorption Fine Structure (EXAFS), a structure characterization tool, was used to determine the local environment of impurities in metal-impurity-metal laminate composites, where the impurities were in monolayer to submonolayer interface concentrations. The third study pertains to the interface fracture in metal-matrix (metal/metal oxide/graphite) composites where a correlation was made between electronic states and fracture path

Empirical model of the high-latitude boundary of the Earth's outer radiation belt at altitudes of up to 1000 km