WorldWideScience

Sample records for boulder removal project

  1. Arroyo Mocho Boulder Removal Project: Lawrence Livermore National Laboratory Hetch Hetchy Pump Station

    Energy Technology Data Exchange (ETDEWEB)

    Burkholder, L; Kato, T; Van Hattem, M

    2007-06-28

    The purpose of this biological assessment is to review the proposed Arroyo Mocho Boulder Removal Project in sufficient detail to determine to what extent the proposed action may affect any of the threatened, endangered, proposed, or sensitive species and designated or proposed critical habitats listed below. In addition, the following information is provided to comply with statutory requirements to use the best scientific and commercial information available when assessing the risks posed to listed and/or proposed species and designated and/or proposed critical habitat by proposed federal actions. This biological assessment is prepared in accordance with legal requirements set forth under regulations implementing Section 7 of the Endangered Species Act (50 CFR 402; 16 U.S.C 1536 (c)). It is our desire for the Arroyo Mocho Boulder Removal Project to receive incidental take coverage for listed species and critical habitat within the greater project area by means of amending the previous formal Section 7 consultation (1-1-04-F-0086) conducted a few hundred meters downstream by Lawrence Livermore National Laboratory (LLNL) in 2002. All conservation measures, terms and conditions, and reporting requirements from the previous Biological Opinion (1-1-04-F-0086) have been adopted for this Biological Assessment and/or amendment.

  2. 78 FR 7775 - Boulder Canyon Project

    Science.gov (United States)

    2013-02-04

    .... \\1\\ 75 FR 57912 (September 23, 2010). \\2\\ 133 FERC ] 62,229. The proposed BCP electric service base... in power rate adjustments (10 CFR part 903) were published on September 18, 1985 (50 FR 87835... Area Power Administration Boulder Canyon Project AGENCY: Western Area Power Administration, DOE....

  3. Final Technical Report - Modernization of the Boulder Canyon Hydroelectric Project

    Energy Technology Data Exchange (ETDEWEB)

    Taddeucci, Joe [Dept. of Public Works, Boulder, CO (United States). Utilities Division

    2013-03-29

    The Boulder Canyon Hydroelectric Project (BCH) was purchased by the City of Boulder, CO (the city) in 2001. Project facilities were originally constructed in 1910 and upgraded in the 1930s and 1940s. By 2009, the two 10 MW turbine/generators had reached or were nearing the end of their useful lives. One generator had grounded out and was beyond repair, reducing plant capacity to 10 MW. The remaining 10 MW unit was expected to fail at any time. When the BCH power plant was originally constructed, a sizeable water supply was available for the sole purpose of hydroelectric power generation. Between 1950 and 2001, that water supply had gradually been converted to municipal water supply by the city. By 2001, the water available for hydroelectric power generation at BCH could not support even one 10 MW unit. Boulder lacked the financial resources to modernize the facilities, and Boulder anticipated that when the single, operational historical unit failed, the project would cease operation. In 2009, the City of Boulder applied for and received a U.S. Department of Energy (DOE) grant for $1.18 million toward a total estimated project cost of $5.155 million to modernize BCH. The federal funding allowed Boulder to move forward with plant modifications that would ensure BCH would continue operation. Federal funding was made available through the American Recovery and Reinvestment Act (ARRA) of 2009. Boulder determined that a single 5 MW turbine/generator would be the most appropriate capacity, given the reduced water supply to the plant. Average annual BCH generation with the old 10 MW unit had been about 8,500 MW-hr, whereas annual generation with a new, efficient turbine could average 11,000 to 12,000 MW-hr. The incremental change in annual generation represents a 30% increase in generation over pre-project conditions. The old turbine/generator was a single nozzle Pelton turbine with a 5-to-1 flow turndown and a maximum turbine/generator efficiency of 82%. The new unit is a

  4. Final Technical Report - Modernization of the Boulder Canyon Hydroelectric Project

    Energy Technology Data Exchange (ETDEWEB)

    Taddeucci, Joe [Dept. of Public Works, Boulder, CO (United States). Utilities Division

    2013-03-29

    The Boulder Canyon Hydroelectric Project (BCH) was purchased by the City of Boulder, CO (the city) in 2001. Project facilities were originally constructed in 1910 and upgraded in the 1930s and 1940s. By 2009, the two 10 MW turbine/generators had reached or were nearing the end of their useful lives. One generator had grounded out and was beyond repair, reducing plant capacity to 10 MW. The remaining 10 MW unit was expected to fail at any time. When the BCH power plant was originally constructed, a sizeable water supply was available for the sole purpose of hydroelectric power generation. Between 1950 and 2001, that water supply had gradually been converted to municipal water supply by the city. By 2001, the water available for hydroelectric power generation at BCH could not support even one 10 MW unit. Boulder lacked the financial resources to modernize the facilities, and Boulder anticipated that when the single, operational historical unit failed, the project would cease operation. In 2009, the City of Boulder applied for and received a U.S. Department of Energy (DOE) grant for $1.18 million toward a total estimated project cost of $5.155 million to modernize BCH. The federal funding allowed Boulder to move forward with plant modifications that would ensure BCH would continue operation. Federal funding was made available through the American Recovery and Reinvestment Act (ARRA) of 2009. Boulder determined that a single 5 MW turbine/generator would be the most appropriate capacity, given the reduced water supply to the plant. Average annual BCH generation with the old 10 MW unit had been about 8,500 MW-hr, whereas annual generation with a new, efficient turbine could average 11,000 to 12,000 MW-hr. The incremental change in annual generation represents a 30% increase in generation over pre-project conditions. The old turbine/generator was a single nozzle Pelton turbine with a 5-to-1 flow turndown and a maximum turbine/generator efficiency of 82%. The new unit is a

  5. Manual Hydraulic Boulder Removal Machine%手动液压巨石移除机

    Institute of Scientific and Technical Information of China (English)

    袁圆; 韩娜; 陈超

    2013-01-01

    在断电和没有大型工程机械的情况下,为了清除阻挡道路的巨石,利用液压缸推力大的原理,提出一种手动多自由度液压巨石移除机。该机器有多个自由度,利用其前后加长杆,方便推移距山体1~5m的巨石,该机器可广泛应用于地震等自然灾害的破障救援中。%In the cases of power failure and no large-scale construction machinery,a manual multi-DOF hydraulic boulder remov-al machine was envisioned to clear the boulders blocking road,applying the theory that hydraulic cylinder had a large thrust. Since the machine has more than one DOF,its front and rear extension rods can be used to remove boulders away from mountain 1~5 m. The machine can be widely used in barrier-breaking rescue in earthquakes and other natural disasters.

  6. 77 FR 64333 - Relocation of Transmission Lines for the U.S. 93 Boulder City Bypass Project, Boulder County, NV...

    Science.gov (United States)

    2012-10-19

    ... for the Project EIS (FHWA-NV-EIS-00-02-F; April 2005; 76 FR 34073). Western was a cooperating agency... needs are satisfied and, with this notice, is adopting the Project EIS for its participation in the... the western end of the Hoover Dam Bypass project near the Hacienda Hotel and Casino. Western...

  7. 75 FR 19966 - Boulder Canyon Project-Post-2017 Application of the Energy Planning and Management Program Power...

    Science.gov (United States)

    2010-04-16

    ... comment period regarding the application of the Energy Planning and Management Program (Program) Power... Western Area Power Administration Boulder Canyon Project--Post-2017 Application of the Energy Planning and Management Program Power Marketing Initiative AGENCY: Western Area Power Administration, DOE. ACTION:...

  8. Flatiron-Erie 115kV transmission line project, Larimer, Weld and Boulder Counties, Colorado

    International Nuclear Information System (INIS)

    Western Area Power Administration (Western) proposes to uprate its existing 115-kV Flatiron-Erie transmission line. The line is located in Larimer, Weld and Boulder Counties, Colorado, and passes through the City of Longmont. The line connects Flatiron Substation and several of the substations supplying Longmont. It is a single circuit 115-kV line, 31.5 miles long, and was built in 1950-51 on a 75-foot wide right-of-way (ROW) using wood H-frame structures. Western proposes to build 27 new structures along the line, to replace or modify 45 of the existing structures and to remote 11 of them. Many of these additions and changes would involve structures that are approximately 5 to 15 feet taller than the existing ones. The existing conductors and ground wires would remain in place. The purpose of these actions would be to allow the power carrying capability of the line to be increased and to replace deteriorating/structural members. Western would be the sole participant in the proposed project. This report gives an analysis of the study area environment and the development of alternative routes. An assessment is presented of the impacts of the primary alternative routes. The environmental consequences of this project are addressed

  9. 77 FR 35671 - Conformed Power Marketing Criteria or Regulations for the Boulder Canyon Project

    Science.gov (United States)

    2012-06-14

    ..., 1987. On December 28, 1984, Western published the 1984 Conformed Criteria (49 FR 50582) to implement... Federal Register (49 FR 50582) on December 28, 1984. These 2012 Conformed Criteria establish general... Area Power Administration Conformed Power Marketing Criteria or Regulations for the Boulder...

  10. Integrated mined-area reclamation and land use planning. Volume 3A. A case study of surface mining and reclamation planning: South Boulder Creek Park Project, Sand and Gravel Operations, Boulder, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, L R; Perry, A O; LaFevers, J R

    1977-02-01

    This case study details reclamation planning for the Flatiron Companies' South Boulder Creek Park Project in Boulder, Colorado. The site contains a deposit of high-quality sand and gravel considered to be one of the best and largest known deposits of aggregate materials in the Front Range area. The aggregate deposit is located in a highly visible site just off the Denver-Boulder Turnpike at the entrance to the city from Denver, and adjacent to a residential portion of the city. In order to make maximum use of pre-mining planning, as a tool for resolving a conflict over the company's proposed operation, an extensive cooperative planning effort was initiated. This included the preparation of an environmental impact assessment, numerous public hearings, operating and reclamation plan review by city authorities, annexation of the site to the city, and the granting of a scenic easement on the property to the city for the development of a regional recreation park. A suite of contractual agreements was worked out among Flatiron Companies, the City of Boulder, the Colorado Open Lands Foundation, and the Federal Bureau of Outdoor Recreation. The purpose of this case study is to allow the planner to gain insight into the procedures, possibilities, and constraints involved in premining planning in a cooperative situation.

  11. 75 FR 57912 - Boulder Canyon Project-Rate Order No. WAPA-150

    Science.gov (United States)

    2010-09-23

    ... Reclamation's post September 11, 2001, security costs be adjusted upward or downward with regard to the CPI. Since the CPI applicable to this budget declined, a corresponding decline in the security costs should... projected security non- reimbursable costs has been incorporated into the final total for the ``Post...

  12. Integrating Infrastructure-Relevant Climate Projections into City Planning: Learning from Boulder CO, Austin TX and Washington DC

    Science.gov (United States)

    Stoner, A. M. K.; Hayhoe, K.

    2015-12-01

    Over the coming century, climate change has the potential to impact infrastructure in many different ways, particularly in population-dense areas that depend on transportation and built environments. Many of these impacts may occur via changes in the frequency and magnitude of extremes: high and low temperature, heat waves, precipitation, coastal flooding, and storm events. Having a better idea of how the climate might change locally, both within the near future as well as toward the end of the century, can give city planners and engineers guidance when designing new structures and when repairing and fortifying existing components of buildings, bridges, highways, sewers, ports, etc. However, the type of event and the amount of damages that may be incurred are often highly specific to a given location. Over the last 10 years, we have worked with a broad range of cities, states, non-profit organizations, and federal agencies to integrate climate projections into ongoing resiliency, sustainability, and management processes. Drawing on that experience, we describe the broad steps in assimilating climate information into existing decision-making frameworks relevant to most applications, as well as highlighting many of the unique aspects of these analyses using examples from our most recent work with three very different cities - Austin TX, Boulder CO and Washington DC. From initial conversations with local experts to identify relevant thresholds to final integration of projected changes into the planning processes of these cities, these case studies highlight the utility of including future climate projections into infrastructure planning, the challenges to doing so, and the over-arching importance of communication and interaction between infrastructure experts, engineers, and scientists.

  13. EXPLOITATION OF GRANITE BOULDER

    Directory of Open Access Journals (Sweden)

    Ivan Cotman

    1994-12-01

    Full Text Available The processes of forming, petrography, features, properties and exploitation of granite boulders are described. The directional drilling and black powder blasting is the succesful method in exploitation of granite boulders (boulder technology (the paper is published in Croatian.

  14. Regenerable Contaminant Removal System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Regenerable Contaminant Removal System (RCRS) is an innovative method to remove sulfur and halide compounds from contaminated gas streams to part-per-billion...

  15. Probability of Boulders

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    1997-01-01

    To collect background information for formulating a description of the expected soil properties along the tunnel line, in 1987 Storebælt initiated a statistical investigation of the occurrence and size of boulders in the Great Belt area. The data for the boulder size distribution were obtained by...

  16. Active Debris Removal Mapping Project

    OpenAIRE

    Nasseri, S Ali; Borriello, Ciro; Hussein, Alaa; Kebe, Fatoumata

    2014-01-01

    Space debris discussions initiated with the start of the space age 55 years ago and have seen special interest in current years. This is due to the large increase in the number of space debris which has led to an increased threat of collision with operational space systems and of unsafe reentry. Due to this increased interest in this area, many different methods have been proposed in recent years for mitigation and space debris removal, some of which have even secured funding from space a...

  17. Boulder Magnetic Observatory

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — These data are vector and scalar component values of the Earth's magnetic field for 2004 recorded at the Boulder Magnetic Observatory in Colorado. Vector values are...

  18. Boulder Creek Critical Zone Observatory Data Management Plan

    OpenAIRE

    Fey, Jeri; Anderson, Suzanne

    2016-01-01

    This Data Management Plan (DMP) was created using the DMPTool. It describes all data collected as part of the the Boulder Creek Critical Zone Observatory (CZO) project, which focuses on research in the Boulder Creek watershed. The project is hosted at the Institute or Arctic and Alpine Research (INSTAAR), University of Colorado at Boulder, USA.The goal for the Boulder Creek CZO is to create and collect meaningful and interesting research of the Earth’s critical zone by making this diverse dat...

  19. 76 FR 43719 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2011-07-21

    ... Colorado Museum, Boulder, CO. The human remains were removed from near Laguna, Cibola County, NM. This... removed from Maxson site number 121, a rock fall near Laguna, Cibola County, NM, by Asa Maxson,...

  20. Analysis and treatment of quality problem of boulder in foundation pile project%基桩遇孤石质量问题的分析与处理

    Institute of Scientific and Technical Information of China (English)

    杨文武

    2015-01-01

    基于地基与基础等强置换、地基压力扩散原理及复合地基理论,以孤石加固法、结构加固法、复合地基与基础加固法及等强补桩法比较,分析了某建筑主体结构已施工基桩遇孤石的承载力、沉降量不能全部满足要求的处理方案,探讨复合地基加固法和等强补桩法的应用。提高土层压缩模量是复合地基加固的重要途径,合理、有效地确定地基处理范围是复合地基加固的重要环节。%Based on the equal strength displacement theory of foundation and foundation, ground pressure diffusion principle and the theory of composite foundation, comparisons of boulder reinforcement method, the structure reinforcement method, composite foundation and pile foundation reinforcement method and equal strength reinforcement method were made.The treatment plan for bearing capacity and settle-ment under requirements due to boulder encountered in a foundation pile which main structure has been built was analyzed.Application of composite foundation reinforcement method and equal strength pile reinforcement method were discussed.Improvement of the soil compres-sion modulus is the important way of compound foundation reinforcement, reasonable and effective determination of the scope of the founda-tion treatment is an important part of the composite foundation reinforcement.

  1. Floor tile and mastic removal project report

    Energy Technology Data Exchange (ETDEWEB)

    1992-11-01

    A test program was developed and coordinated with State and Federal Regulators and carried out at Fort Sill, Oklahoma. This program was carefully designed to create the worst conditions in order to evaluate whether asbestos fibers are released when asbestos containing floor tile and mastic are removed. There were over 1,000 samples taken and analyzed during the execution of the program. The conclusions reached were based upon analysis of the critical samples using the Transmission Electron Microscope (TEM) technology. Additionally, the TEM procedures were used to evaluate personnel samples to determine whether those fibers found were asbestos or other materials. Most of the (TEM) samples were analyzed by the US Environmental Protection Agency (EPA) Risk Reduction Engineering Laboratory in Cincinnati, Ohio.

  2. Debris Removal Project K West Canister Cleaning System Performance Specification

    Energy Technology Data Exchange (ETDEWEB)

    FARWICK, C.C.

    1999-12-09

    Approximately 2,300 metric tons Spent Nuclear Fuel (SNF) are currently stored within two water filled pools, the 105 K East (KE) fuel storage basin and the 105 K West (KW) fuel storage basin, at the U.S. Department of Energy, Richland Operations Office (RL). The SNF Project is responsible for operation of the K Basins and for the materials within them. A subproject to the SNF Project is the Debris Removal Subproject, which is responsible for removal of empty canisters and lids from the basins. Design criteria for a Canister Cleaning System to be installed in the KW Basin. This documents the requirements for design and installation of the system.

  3. Boulder Dislodgement by Tsunamis and Storms: Version 2.0

    Science.gov (United States)

    Weiss, Robert

    2016-04-01

    In the past, boulder dislodgement by tsunami and storm waves has been approached with a simple threshold approach in which a boulder was moved if the sum of the acting forces on the boulder is larger than zero. The impulse theory taught us, however, that this criterion is not enough to explain particle dislodgement. We employ an adapted version of the Newton's Second Law of Motion (NSLM) in order to consider the essence of the impulse theory which is that the sum of the forces has to exceed a certain threshold for a certain period of time. Furthermore, a classical assumption is to consider linear waves. However, when waves travel toward the shore, they alter due to non-linear processes. We employ the TRIADS model to quantify that change and how it impacts boulder dislodgement. We present our results of the coupled model (adapted NSLM and TRIADS model). The results project a more complex picture of boulder transport by storms and tsunami. The following question arises: What information do we actually invert, and what does it tell us about the causative event?

  4. Columbia River Channel Improvement Project Rock Removal Blasting: Monitoring Plan

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, Thomas J.; Johnson, Gary E.

    2010-01-29

    This document provides a monitoring plan to evaluate take as outlined in the National Marine Fisheries Service 2002 Biological Opinion for underwater blasting to remove rock from the navigation channel for the Columbia River Channel Improvement Project. The plan was prepared by the Pacific Northwest National Laboratory (PNNL) for the U.S. Army Corps of Engineers (USACE), Portland District.

  5. Asbestos removal at the Shippingport Station Decommissioning Project

    International Nuclear Information System (INIS)

    Asbestos was used as an insulation material at the Shippingport Atomic Power Station on tanks, vessels, piping, duct work, building and equipment. It must be removed before any equipment disassembling and removal can be started. Asbestos is located in both Radiologically Controlled Areas (RCA) and Non-Radiologically Controlled Areas (Non-RCA) in the plant. Precautions and special handling procedures must be followed in order to minimize potential hazard to personnel and the environment. In the handling of asbestos material, guidelines can be found in the Code of Federal Regulations. A thorough survey was conducted to identify the location and quantity of asbestos in the plant. The amount of asbestos in the plant involves about 9000 linear feet of piping (100 cu. yard in volume) in the Non-RCA and 21,000 linear feet of piping (330 cu. yard in volume) in the RCA. This asbestos removal effort is expected to be completed at Shippingport within 12 months duration beginning August, 1985. In this paper, activities associated with asbestos removal, prerequisites to be performed before the project is started, sequence of operations, procedures and instructions, potential hazards and precautions and methods of disposal will be discussed. Recommendations for similar efforts in the future will be provided

  6. 100-KE REACTOR CORE REMOVAL PROJECT ALTERNATIVE ANALYSIS WORKSHOP REPORT

    Energy Technology Data Exchange (ETDEWEB)

    HARRINGTON RA

    2010-01-15

    On December 15-16, 2009, a 100-KE Reactor Core Removal Project Alternative Analysis Workshop was conducted at the Washington State University Consolidated Information Center, Room 214. Colburn Kennedy, Project Director, CH2M HILL Plateau Remediation Company (CHPRC) requested the workshop and Richard Harrington provided facilitation. The purpose of the session was to select the preferred Bio Shield Alternative, for integration with the Thermal Shield and Core Removal and develop the path forward to proceed with project delivery. Prior to this workshop, the S.A. Robotics (SAR) Obstruction Removal Alternatives Analysis (565-DLV-062) report was issued, for use prior to and throughout the session, to all the team members. The multidisciplinary team consisted ofrepresentatives from 100-KE Project Management, Engineering, Radcon, Nuclear Safety, Fire Protection, Crane/Rigging, SAR Project Engineering, the Department of Energy Richland Field Office, Environmental Protection Agency, Washington State Department of Ecology, Defense Nuclear Facility Safety Board, and Deactivation and Decommission subject matter experts from corporate CH2M HILL and Lucas. Appendix D contains the workshop agenda, guidelines and expectations, opening remarks, and attendance roster going into followed throughout the workshop. The team was successful in selecting the preferred alternative and developing an eight-point path forward action plan to proceed with conceptual design. Conventional Demolition was selected as the preferred alternative over two other alternatives: Diamond Wire with Options, and Harmonic Delamination with Conventional Demolition. The teams preferred alternative aligned with the SAR Obstruction Removal Alternative Analysis report conclusion. However, the team identified several Path Forward actions, in Appendix A, which upon completion will solidify and potentially enhance the Conventional Demolition alternative with multiple options and approaches to achieve project delivery

  7. 78 FR 48670 - Boulder Canyon Project

    Science.gov (United States)

    2013-08-09

    ... installed capacity of 2,078,800 kilowatts (kW) (4,800 kW for plant use). High-voltage transmission lines and... several categories. Expenses for operation and maintenance expenses, the uprating program, the visitor... determining the Base Charge and Rates: 1. A Federal Register notice was published on February 4, 2013 (78...

  8. 76 FR 56430 - Boulder Canyon Project

    Science.gov (United States)

    2011-09-13

    .... Security Costs Comment: A commenter expressed concern that the security costs are increasing even while the... continually reviews its security costs and seeks ways to reduce its overall costs. Hoover Dam security costs... security costs are spent in accordance with current Reclamation Legislative Guidelines, and......

  9. 77 FR 48151 - Boulder Canyon Project

    Science.gov (United States)

    2012-08-13

    ... and Rates: 1. A Federal Register notice was published on January 18, 2012 (77 FR 2533), announcing the... adjustments are located at 10 CFR part 903, effective September 18, 1985 (50 FR 37835), and 18 CFR part 300..., 2012 (77 FR 2533). Under Delegation Order Nos. 00-037.00 and 00-001.00C, and in compliance with 10...

  10. 77 FR 2533 - Boulder Canyon Project

    Science.gov (United States)

    2012-01-18

    ... public comment forum will be held at the Desert Southwest Customer Service Regional Office, located at... Darrick Moe, Regional Manager, Desert Southwest Customer Service Region, Western Area Power Administration... (602) 605-2490, attention: Jack Murray. Western will post information about the rate processes on...

  11. 76 FR 8359 - Boulder Canyon Project

    Science.gov (United States)

    2011-02-14

    ... forum and public comment forum will be held at the Desert Southwest Customer Service Regional Office... sent to Darrick Moe, Regional Manager, Desert Southwest Customer Service Region, Western Area Power... to (602) 605-2490, Attention: Jack Murray. Western will post information about the rate processes...

  12. Do Cement Boulders Mimic Natural Boulders for Macro-Invertebrates in the Southern Caspian Sea?

    OpenAIRE

    Pourjomeh, Fatemeh; Shokri, Mohammad Reza; Kiabi, Bahram

    2014-01-01

    The macro-invertebrates on natural (rock) and artificial (cement) boulders were compared along the southern Caspian Sea and the effect of structural features of boulders (i.e. orientation, facing, surface complexity, the degree of exposure to the wave action) on macro-invertebrate communities were investigated. Ten locations with rock walls in the southern Caspian Sea were investigated in which the isolated boulders of natural and artificial types with similar dimensions were haphazardly ...

  13. Novel Long-Term CO2 Removal System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Current Technology for CO2 removal from enclosed air of spacecraft utilizes LiOH canisters for CO2 absorption. This absorption is irreversible so longer flights...

  14. Removing Mid-Spatial Frequency Errors with VIBE Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Optimax VIBE process is a full-aperture, conformal polishing process incorporating high frequency motion that rapidly removes sub-surface damage in a VIBE...

  15. Collaboration Between Environmental Water Chemistry Students and Hazardous Waste Treatment Specialists on the University of Colorado-Boulder Campus

    Science.gov (United States)

    Dittrich, T. M.

    2012-12-01

    The University of Colorado-Boulder is one of a few universities in the country that has a licensed Treatment, Storage, and Disposal Facility (TSDF) for hazardous waste on campus. This facility, located on the bottom floor of the Environmental Health and Safety (EH&S) building, allows CU to more economically treat hazardous waste by enabling treatment specialists on staff to safely collect and organize the hazardous waste generated on campus. Hazardous waste is anything that contains a regulated chemical or compound and most chemicals used in engineering labs (e.g., acids, solvents, metal solutions) fall into this category. The EH&S staff is able to treat close almost 33% of the waste from campus and the rest is packed for off-site treatment at various places all over the country for disposal (e.g., Sauget, IL, Port Aurthor, TX). The CU-Boulder campus produced over 50 tons of hazardous waste in 2010 costing over $300,000 in off-campus expenses. The EH&S staff assigns one of over 50 codes to the waste which will determine if the waste can be treated on campus of must be shipped off campus to be disposed of. If the waste can be treated on campus, it will undergo one of three processes: 1) neutralization, 2) UV-ozone oxidation, or 3) ion exchange. If the waste is acidic but contains no heavy metals, the acid is neutralized with sodium hydroxide (a base) and can be disposed "down the drain" to the Boulder Wastewater Treatment Plant. If the waste contains organic compounds and no metals, a UV-ozone oxidation system is used to break down the organic compounds. Silver from photography wastewater can be removed using ion exchange columns. Undergraduate and graduate students worked with the hazardous waste treatment facility at the Environmental Health and Safety (EH&S) building on the CU-Boulder campus during the fall of 2011 and fall of 2012. Early in the semester, students receive a tour of the three batch treatment processes the facility is equipped with. Later in the

  16. Relocalising disaster risk reduction in Boulder, Colorado

    OpenAIRE

    Kelman, I.; Karnes, E.

    2007-01-01

    Relocalisation aims to return communities to a more local basis from their current, relatively centralised and transport-dependent systems, in sectors such as food, energy, and manufacturing. Disaster risk reduction can also be relocalised, in line with practices which involve local residents in disaster-related activities, pre-disaster such as mitigation and prevention and post-disaster such as response and recovery, rather than relying on post-event external assistance. Boulder Valley, Colo...

  17. Tsunami-induced boulder transport - combining physical experiments and numerical modelling

    Science.gov (United States)

    Oetjen, Jan; Engel, Max; May, Simon Matthias; Schüttrumpf, Holger; Brueckner, Helmut; Prasad Pudasaini, Shiva

    2016-04-01

    Coasts are crucial areas for living, economy, recreation, transportation, and various sectors of industry. Many of them are exposed to high-energy wave events. With regard to the ongoing population growth in low-elevation coastal areas, the urgent need for developing suitable management measures, especially for hazards like tsunamis, becomes obvious. These measures require supporting tools which allow an exact estimation of impact parameters like inundation height, inundation area, and wave energy. Focussing on tsunamis, geological archives can provide essential information on frequency and magnitude on a longer time scale in order to support coastal hazard management. While fine-grained deposits may quickly be altered after deposition, multi-ton coarse clasts (boulders) may represent an information source on past tsunami events with a much higher preservation potential. Applying numerical hydrodynamic coupled boulder transport models (BTM) is a commonly used approach to analyse characteristics (e.g. wave height, flow velocity) of the corresponding tsunami. Correct computations of tsunamis and the induced boulder transport can provide essential event-specific information, including wave heights, runup and direction. Although several valuable numerical models for tsunami-induced boulder transport exist (e. g. Goto et al., 2007; Imamura et al., 2008), some important basic aspects of both tsunami hydrodynamics and corresponding boulder transport have not yet been entirely understood. Therefore, our project aims at these questions in four crucial aspects of boulder transport by a tsunami: (i) influence of sediment load, (ii) influence of complex boulder shapes other than idealized rectangular shapes, (iii) momentum transfers between multiple boulders, and (iv) influence of non-uniform bathymetries and topographies both on tsunami and boulder. The investigation of these aspects in physical experiments and the correct implementation of an advanced model is an urgent need

  18. Evaluation of an Unsuccessful Brook Trout Electrofishing Removal Project in a Small Rocky Mountain Stream.

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Kevin A.; Lamansky, Jr., James A.; Schill, Daniel J.

    2006-01-26

    In the western United States, exotic brook trout Salvelinus fontinalis frequently have a deleterious effect on native salmonids, and biologists often attempt to remove brook trout from streams by means of electrofishing. Although the success of such projects typically is low, few studies have assessed the underlying mechanisms of failure, especially in terms of compensatory responses. A multiagency watershed advisory group (WAG) conducted a 3-year removal project to reduce brook trout and enhance native salmonids in 7.8 km of a southwestern Idaho stream. We evaluated the costs and success of their project in suppressing brook trout and looked for brook trout compensatory responses, such as decreased natural mortality, increased growth, increased fecundity at length, and earlier maturation. The total number of brook trout removed was 1,401 in 1998, 1,241 in 1999, and 890 in 2000; removal constituted an estimated 88% of the total number of brook trout in the stream in 1999 and 79% in 2000. Although abundance of age-1 and older brook trout declined slightly during and after the removals, abundance of age-0 brook trout increased 789% in the entire stream 2 years after the removals ceased. Total annual survival rate for age-2 and older brook trout did not decrease during the removals, and the removals failed to produce an increase in the abundance of native redband trout Oncorhynchus mykiss gairdneri. Lack of a meaningful decline and unchanged total mortality for older brook trout during the removals suggest that a compensatory response occurred in the brook trout population via reduced natural mortality, which offset the removal of large numbers of brook trout. Although we applaud WAG personnel for their goal of enhancing native salmonids by suppressing brook trout via electrofishing removal, we conclude that their efforts were unsuccessful and suggest that similar future projects elsewhere over such large stream lengths would be costly, quixotic enterprises.

  19. Analysis of registered CDM projects: potential removal of evidenced bottlenecks

    Energy Technology Data Exchange (ETDEWEB)

    Agosto, D.; Bombard, P.; Gostinelli, F.

    2007-07-01

    The Clean Development Mechanism (CDM) has developed during its first period of implementation, a distinctive set of patterns. The authors thought of concentrating on the CDM analysis in order to highlight potential remedies or reasons for given bottlenecks. In order to establish a sort of extensive SWOT analysis for CDMs, all the 356 projects actually (November 2006) registered at UNFCCC were examined, together with all the about 1000 PDDs presented to the UNFCCC but not registered yet. The CDM projects have been studied trying to cluster projects according to relevant characteristics, both from a technical and an economic point of view. Chosen indicators are meant to identify: more convenient/more diffused energy system for a CDM; reasons for a geographical distribution of different types of projects; potentials for a future exploitation of lower used technologies in CDM. Conclusions are drawn and appropriate tables and graphs presented. (1) the Baseline Emission Factor, combined to economic patterns, is the pivotal factor that characterizes both choices of host country and technology; (2) some technologies can exploit appropriately CDM scheme, whilst other technologies, are constrained by it. (3) there are still some important weak points: grouping of non Annex I countries; crediting period; criteria for the evaluation of sustainable development. (auth)

  20. The distribution and source of boulders on asteroid 4179 Toutatis

    Science.gov (United States)

    Jiang, Yun; Ji, Jianghui; Huang, Jiangchuan; Marchi, Simone; Li, Yuan; Ip, Wing-Huen

    2016-01-01

    Boulders are ubiquitous on the surfaces of asteroids and their spatial and size distributions provide information for the geological evolution and collisional history of parent bodies. We identify more than 200 boulders on near-Earth asteroid 4179 Toutatis based on images obtained by Chang'e-2 flyby. The cumulative boulder size frequency distribution (SFD) gives a power-index of -4.4 +/- 0.1, which is clearly steeper than those of boulders on Itokawa and Eros, indicating much high degree of fragmentation. Correlation analyses with craters suggest that most boulders cannot solely be produced as products of cratering, but are probably survived fragments from the parent body of Toutatis, accreted after its breakup. Similar to Itokawa, Toutatis probably has a rubble-pile structure, but owns a different preservation state of boulders.

  1. DOE Zero Energy Ready Home Case Study: Boulder ZED Design Build - Boulder, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2014-11-01

    This case study describes a DOE Zero Energy Ready Home in Boulder, Colorado, that scored HERS 38 without PV and 0 with PV. This 2,504 ft2 custom home has advanced framed walls, superior insulation a ground-source heat pump, ERV, and triple-pane windows.

  2. Removal Action Plan for the Accelerated Retrieval Project for a Described Area within Pit 4

    Energy Technology Data Exchange (ETDEWEB)

    A. M. Tyson

    2006-08-01

    This Removal Action Plan documents the plan for implementation of the Comprehensive Environmental Response, Compenstion, and Liability Act non-time-critical removal action to be performed by the Accelerated Retrieval Project. The focus of the action is the limited excavation and retrieval of selected waste streams from a designated portion of the Radioactive Waste Management Complex Subsurface Disposal Area that are contaminated with volatile organic compounds, isotopes of uranium, or transuranic radionuclides. The selected retrieval area is approximately 0.2 ha (1/2 acre) and is located in the eastern portion of Pit 4. The proposed project is referred to as the Accelerated Retrieval Project. This Removal Action Plan details the major work elements, operations approach, and schedule, and summarizes the environmental, safety and health, and waste management considerations associated with the project.

  3. Removal Action Plan for the Accelerated Retrieval Project for a Described Area within Pit 4

    International Nuclear Information System (INIS)

    This Removal Action Plan documents the plan for implementation of the Comprehensive Environmental Response, Compensation, and Liability Act non-time-critical removal action to be performed by the Accelerated Retrieval Project. The focus of the action is the limited excavation and retrieval of selected waste streams from a designated portion of the Radioactive Waste Management Complex Subsurface Disposal Area that are contaminated with volatile organic compounds, isotopes of uranium, or transuranic radionuclides. The selected retrieval area is approximately 0.2 ha (1/2 acre) and is located in the eastern portion of Pit 4. The proposed project is referred to as the Accelerated Retrieval Project. This Removal Action Plan details the major work elements, operations approach, and schedule, and summarizes the environmental, safety and health, and waste management considerations associated with the project

  4. Onshore Transport of Large Nearshore Boulders during Super Typhoon Haiyan

    Science.gov (United States)

    Kennedy, A. B.; Mori, N.; Zhang, Y.; Tajima, Y.; Pecor, W.; Yasuda, T.; Chen, S. E.; Nakamura, S.; Cruz, E.

    2014-12-01

    Super Typhoon Haiyan made a Philippines landfall in November, 2013 as one of the strongest storms in history. The coast of Eastern Samar Province has deep water very close to shore and experienced extreme wave conditions, with hindcast Hs>18m near landfall. These waves generated large shoreline runup, and caused severe damage to coastal communities even though hindcast storm surge was consequence of the storm was the transport of very large (up to 5m length) boulders shoreward to elevations near 10m, where they were stranded as waves and surge diminished. This presentation describes a field survey of a boulder field on Calicoan Island, combined with Boussinesq simulation of the nearshore storm hydrodynamics and boulder transport modeling using a modified version of the Imamura et al. methodology. Results show highly intermittent shoreward boulder transport driven by infragravity runup, with both inertial and drag forces significant. Boulder transport distance was found to be sensitive to wave properties, enough so that it may in some instances be possible to estimate hydrodynamic properties of historical storms. The coastal boulder transport literature often features uncertainty about whether boulder fields with unknown origin were generated by storms or by tsunamis, and has suggested that coastal storms can not transport boulders very far inland. However, the present work demonstrates that the potential to transport large boulders far onshore to high inland elevations does not lie exclusively with tsunamis, but can also be achieved by strong tropical cyclones.

  5. University of Colorado at Boulder: Energy and Climate Revolving Fund. Green Revolving Funds in Action: Case Study Series

    Science.gov (United States)

    Caine, Rebecca

    2012-01-01

    The University of Colorado at Boulder's student run Environmental Center leads the campus' sustainability efforts. The Center created the Energy and Climate Revolving Fund (ECRF) in 2007 to finance energy-efficiency upgrades. The ECRF functions as a source of funding for project loans and provides a method of financing projects that seeks to save…

  6. Spent nuclear fuel removal program at the West Valley Demonstration Project: Topical report

    Energy Technology Data Exchange (ETDEWEB)

    Connors, B. J.; Golden, M. P.; Valenti, P. J.; Winkel, J. J.

    1987-03-01

    The spent nuclear fuel removal program at the West Valley Demonstration Project (WVDP) consisted of removing the spent nuclear fuel (SNF) assemblies from the storage pool in the plant, loading them in shielded casks, and preparing the casks for transportation. So far, four fuel removal campaigns have been completed with the return of 625 spent nuclear fuel assemblies to their four utility owners. A fifth campaign, which is not yet completed, will transfer the remaining 125 fuel assemblies to a government site in Idaho. A spent fuel rod consolidation demonstration has been completed, and the storage canisters and their racks are being removed from the fuel receiving and storage pool to make way for installation of the size reduction equipment. A brief history of the West Valley reprocessing plant and the events leading to the storage and ownership of the spent nuclear fuel assemblies and their subsequent removal from West Valley are also recorded as background information. 3 refs., 16 figs., 9 tabs.

  7. Spent nuclear fuel removal program at the West Valley Demonstration Project: Topical report

    International Nuclear Information System (INIS)

    The spent nuclear fuel removal program at the West Valley Demonstration Project (WVDP) consisted of removing the spent nuclear fuel (SNF) assemblies from the storage pool in the plant, loading them in shielded casks, and preparing the casks for transportation. So far, four fuel removal campaigns have been completed with the return of 625 spent nuclear fuel assemblies to their four utility owners. A fifth campaign, which is not yet completed, will transfer the remaining 125 fuel assemblies to a government site in Idaho. A spent fuel rod consolidation demonstration has been completed, and the storage canisters and their racks are being removed from the fuel receiving and storage pool to make way for installation of the size reduction equipment. A brief history of the West Valley reprocessing plant and the events leading to the storage and ownership of the spent nuclear fuel assemblies and their subsequent removal from West Valley are also recorded as background information. 3 refs., 16 figs., 9 tabs

  8. Local late Amazonian boulder breakdown and denudation rate on Mars

    NARCIS (Netherlands)

    de Haas, T.; Hauber, E.; Kleinhans, M.G.

    2013-01-01

    Inactive fan surfaces become smoother and develop desert pavement over time by weathering and erosion. We use this mechanism to estimate late Amazonian boulder breakdown and surface denudation rates on a young (∼1.25 Ma) (Schon et al., 2009) fan on Mars. This is done by comparing boulder size and su

  9. Treatment techniques for removing natural radionuclides from drinking water. Final report of the TENAWA project

    International Nuclear Information System (INIS)

    TENAWA project (Treatment Techniques for Removing Natural Radionuclides from Drinking Water) was carried out on a cost-shared basic with the European Commission (CEC) under the supervision of Directorate-General XII, Radiation Protection Unit. TENAWA project was started because in several European countries ground water supplies may contain high amounts of natural radionuclides. During the project both laboratory and field research was performed in order to test the applicability of different equipment and techniques for removing natural radionuclides from drinking water. The measurable objectives of the project were: to give recommendations on the most suitable methods for removing radon (222Rn), uranium (238,234U), radium (226, 228Ra), lead (210Pb) and polonium (210Po) from drinking water of different qualities (i.e. soft, hard, iron-, manganese- and humus-rich, acidic) to test commercially available equipment for its ability to remove radionuclides; to find new materials, absorbents and membranes effective in the removal of radionuclides and to issue guidelines for the treatment and disposal of radioactive wastes produced in water treatment. Radon could be removed efficiently (>95%) from domestic water supplies by both aeration and granular activated carbon (GAC) filtration. Defects in technical reliability or radon removal efficiency were observed in some aerators. The significant drawback of GAC filtration was the elevated gamma dose rates (up to 120 μSv/h) near the filter and the radioactivity of spent GAC. Aeration was found to be a suitable method for removing radon at waterworks, too. The removal efficiencies at waterworks where the aeration process was designed to remove radon or carbon dioxide were 67-99%. If the aeration process was properly designed, removal efficiencies higher than 95% could be attained. Uranium could best be removed (>95%) with strong basic anion exchange resins and radium by applying strong acidic cation exchange resins. Also, weak

  10. Treatment techniques for removing natural radionuclides from drinking water. Final report of the TENAWA project

    Energy Technology Data Exchange (ETDEWEB)

    Annanmaeki, M.; Turtiainen, T. [eds.

    2000-01-01

    TENAWA project (Treatment Techniques for Removing Natural Radionuclides from Drinking Water) was carried out on a cost-shared basic with the European Commission (CEC) under the supervision of Directorate-General XII, Radiation Protection Unit. TENAWA project was started because in several European countries ground water supplies may contain high amounts of natural radionuclides. During the project both laboratory and field research was performed in order to test the applicability of different equipment and techniques for removing natural radionuclides from drinking water. The measurable objectives of the project were: to give recommendations on the most suitable methods for removing radon ({sup 222}Rn), uranium ({sup 238,234}U), radium ({sup 226}, {sup 228}Ra), lead ({sup 210}Pb) and polonium ({sup 210}Po) from drinking water of different qualities (i.e. soft, hard, iron-, manganese- and humus-rich, acidic) to test commercially available equipment for its ability to remove radionuclides; to find new materials, absorbents and membranes effective in the removal of radionuclides and to issue guidelines for the treatment and disposal of radioactive wastes produced in water treatment. Radon could be removed efficiently (>95%) from domestic water supplies by both aeration and granular activated carbon (GAC) filtration. Defects in technical reliability or radon removal efficiency were observed in some aerators. The significant drawback of GAC filtration was the elevated gamma dose rates (up to 120 {mu}Sv/h) near the filter and the radioactivity of spent GAC. Aeration was found to be a suitable method for removing radon at waterworks, too. The removal efficiencies at waterworks where the aeration process was designed to remove radon or carbon dioxide were 67-99%. If the aeration process was properly designed, removal efficiencies higher than 95% could be attained. Uranium could best be removed (>95%) with strong basic anion exchange resins and radium by applying strong

  11. 77 FR 50916 - Safety Zone; Boston Harbor's Rock Removal Project, Boston Inner Harbor, Boston, MA

    Science.gov (United States)

    2012-08-23

    ... INFORMATION: Table of Acronyms DHS Department of Homeland Security FR Federal Register NPRM Notice of Proposed..., Boston Inner Harbor, Boston, MA AGENCY: Coast Guard, DHS. ACTION: Temporary final rule. SUMMARY: The... Zone; Boston Harbor's Rock Removal Project, Boston Inner Harbor, Boston, MA. (a) General. A...

  12. Arsenic Removal from Drinking Water by Iron Removal U.S. EPA Demonstration Project at Vintage on the Ponds in Delavan, WI Final Performance Evaluation Report

    Science.gov (United States)

    This report documents the activities performed and the results obtained for the arsenic removal treatment technology demonstration project at Vintage on the Ponds in Delavan, WI. The objectives of the project were to evaluate: (1) the effectiveness of a Kinetico Macrolite® press...

  13. Arsenic Removal from Drinking Water by Iron Removal - U.S. EPA Demonstration Project at Northeastern Elementary School in Fountain City, IN - Final Performance Evaluation Report

    Science.gov (United States)

    This report documents the activities performed and the results obtained from the arsenic removal treatment technology demonstration project at Northeastern Elementary School in Fountain City, IN. The main objective of the project was to evaluate the effectiveness of US Water Sys...

  14. ARSENIC REMOVAL FROM DRINKING WATER BY IRON REMOVAL AND ADSORPTIVE MEDIA USEPA DEMONSTRATION PROJECT AT STEWART, MN. SIX-MONTH EVALUATION REPORT

    Science.gov (United States)

    This report documents the activities performed and the results obtained from the first six months of the EPA arsenic removal technology demonstration project at the Stewart, MN facility. The main objective of the project is to evaluate the effectiveness of Siemens¿ Type II AERALA...

  15. Arsenic Removal from Drinking Water by Iron Removal and Adsorptive Media U.S. EPA Demonstration Project at Stewart, MN, Final Performance Evaluation Report

    Science.gov (United States)

    This report documents the activities performed and the results obtained from the one-year U.S. Environmental Protection Agency (EPA) arsenic removal technology demonstration project at the Stewart, MN facility. The main objective of the project was to evaluate the effectiveness ...

  16. Small-Scale Spatial Variability of Ozone in Boulder, Colorado

    Science.gov (United States)

    Deanes, L. N.; Sadighi, K.; Casey, J. G.; Collier, A. M.; Hannigan, M.

    2015-12-01

    Surface ozone (O3) can pose several health risks to humans, such as an increased number of and intensity of asthma attacks. Considering this, it is important that ozone levels are monitored. While municipal air quality monitors are present in cities like Boulder, Colorado, these monitors often only consider regional analysis, neglecting the variability of compounds, such as ozone or carbon monoxide, over smaller distances. Small-scale (approximately 1 kilometer) spatial variability in ozone is important because humans experience these small scales on a daily basis. Using low-cost, next-generation air quality monitors ("pods") developed at the University of Colorado-Boulder, we assessed small-scale spatial variability of surface ozone in Boulder, Colorado. This was done by placing clusters of 4-5 pods within approximately 1 kilometer of each other at specific sites in the city of Boulder. We collected data at two sites: one on the University of Colorado-Boulder campus (i.e., an urban site) and one outside of the city (i.e., a rural site). Pods were left in their positions for one to two weeks allowing for observation of ozone trends. As expected the typical diurnal trend was observed; however, further analysis revealed differences between these daily trends. Data collected by the pods allows for better understanding of small-scale spatial variability of surface ozone and how this may be driven by nearby sources.

  17. Dual signal subspace projection (DSSP): a novel algorithm for removing large interference in biomagnetic measurements

    Science.gov (United States)

    Sekihara, Kensuke; Kawabata, Yuya; Ushio, Shuta; Sumiya, Satoshi; Kawabata, Shigenori; Adachi, Yoshiaki; Nagarajan, Srikantan S.

    2016-06-01

    Objective. In functional electrophysiological imaging, signals are often contaminated by interference that can be of considerable magnitude compared to the signals of interest. This paper proposes a novel algorithm for removing such interferences that does not require separate noise measurements. Approach. The algorithm is based on a dual definition of the signal subspace in the spatial- and time-domains. Since the algorithm makes use of this duality, it is named the dual signal subspace projection (DSSP). The DSSP algorithm first projects the columns of the measured data matrix onto the inside and outside of the spatial-domain signal subspace, creating a set of two preprocessed data matrices. The intersection of the row spans of these two matrices is estimated as the time-domain interference subspace. The original data matrix is projected onto the subspace that is orthogonal to this interference subspace. Main results. The DSSP algorithm is validated by using the computer simulation, and using two sets of real biomagnetic data: spinal cord evoked field data measured from a healthy volunteer and magnetoencephalography data from a patient with a vagus nerve stimulator. Significance. The proposed DSSP algorithm is effective for removing overlapped interference in a wide variety of biomagnetic measurements.

  18. Resistance forces during boulder extraction from an asteroid

    Science.gov (United States)

    Kulchitsky, Anton V.; Johnson, Jerome B.; Reeves, David M.

    2016-10-01

    Planning for NASA's Asteroid Redirect Mission (ARM) requires estimating the forces that appear during extraction of a boulder from the surface of an asteroid with unknown surface regolith properties. These forces are estimated for a vertical constant force or acceleration pull and a rolling, constant force, torque (peel) on a 4-m diameter spherical boulder using both analytic and discrete element method (DEM) models considering the effects of microgravity and regolith cohesion using Johnson-Kendall-Roberts (JKR) model. Estimates of the bulk asteroid regolith cohesion strength derived from lunar and asteroid regolith studies ranged from 25 Pa to 250 Pa. JKR cohesive forces at particle contacts depend on particle surface energy and effective curvature radius (particle size). DEM particle size dependent cohesion parameters are linked to estimated regolith cohesion strength by simulating shear and tension tests over a range of DEM particle surface energies resulting in the formulation of the dependence of particle surface energy as a function of cohesion strength and particle size. Maximum extraction forces occur for a vertical pull through the boulder center of mass with constant acceleration. Extraction force decreases for a constant force pull to 0.62pc S where S is the boulder surface area embedded in the regolith and pc is the cohesion strength of the regolith. Boulder extraction by peeling produces the smallest forces by up to more than a factor of 2, as the failure across the boulder surface increases progressively rather than being fully engaged as occurs during a vertical pull extraction. Variations between DEM and analytic results differed from 9% to 17% over the range of regolith cohesion values and peel extraction leverage.

  19. Space debris removal by ground-based lasers: main conclusions of the European project CLEANSPACE.

    Science.gov (United States)

    Esmiller, Bruno; Jacquelard, Christophe; Eckel, Hans-Albert; Wnuk, Edwin

    2014-11-01

    Studies show that the number of debris in low Earth orbit is exponentially growing despite future debris release mitigation measures considered. Specifically, the already existing population of small and medium debris (between 1 cm and several dozens of cm) is today a concrete threat to operational satellites. A ground-based laser solution which can remove, at low expense and in a nondestructive way, hazardous debris around selected space assets appears as a highly promising answer. This solution is studied within the framework of the CLEANSPACE project which is part of the FP7 space program. The overall CLEANSPACE objective is: to propose an efficient and affordable global system architecture, to tackle safety regulation aspects, political implications and future collaborations, to develop affordable technological bricks, and to establish a roadmap for the development and the future implantation of a fully functional laser protection system. This paper will present the main conclusions of the CLEANSPACE project. PMID:25402937

  20. A story about distributions of dimensions and locations of boulders

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    2006-01-01

    for making a bored tunnel through the till deposit. Geographical universality was discovered through the statistical analysis of observations of boulder coordinates and dimension measures from wide spread cliff beach locations. One conclusion is that the joint size distribution up to some degree of modeling...... distribution. Moreover, these ratios are independent of the maximal dimension. The random point field structure of the boulder coordinates as isolated points or as clusters of points makes Poisson fields reasonable modeling candidates for the fields of both single points and cluster points. The cluster size...

  1. Surface Macrofabric of Boulder Dominated Desert Mountain Slopes, California, USA

    Institute of Scientific and Technical Information of China (English)

    Donald A. FRIEND

    2005-01-01

    Rhyolite domes formed over a million year continuum in eastern California are used to study boulder dominated slopes. Slopes in this study are steep (~25° to ~35°) and are made of coarse boulder sized blocks. These slopes include well varnished vertically oriented eolluvial deposits that have been likened to relict periglacial stone stripes, or as indicated in this study, are the result of ongoing desert slope processes. The deposits are common throughout the arid southwestern US, but their morphometric character, fabric, and rates of formation have not been assessed systematically.Results indicate that boulder deposits examined here are remnant from the original surface formed during volcanic eruption and that these boulder slope deposits evolve slowly. Grain size, grain shape and grain angularity do not change significantly from genesis to ~0.6 Ma; trends in the data change markedly after that time. Mean eigenvectors indicate a fabric oriented downhill, parallel to the slope,consistent with the visual impression that long thin to plate-like rocks orient themselves similarly; however,fabric is actually randomly dispersed, similar to that at slope genesis, as indicated by the eigenvalue analysis resultants of C and K. Interestingly, grains remain or become more angular over the million-year time scale of the study as they decrease in size,indicating active in situ weathering processes on individual grains; this result is counter to the common assumption that as grains weather they become more rounded over time.

  2. Erratic boulders in Switzerland, a geological and cultural heritage

    Science.gov (United States)

    Reynard, Emmanuel

    2015-04-01

    Erratic boulders are stones transported over quite long distances by glaciers and that differ from the type of rock upon which they rely. They range from the size of pebbles to large boulders weighing several thousand tons. Erratic boulders are significant geosites (Reynard, 2004) for several reasons. (1) First, they are indicators of former glacier extensions by marking glaciers' path, size and volume. In Switzerland, they allowed mapping the extension of large Alpine glaciers (the Rhine and Rhone glaciers, in particular) and their retreat stages (e.g. the Monthey erratic boulders that mark an important lateglacial stage of the Rhone glacier). Crystalline erratic boulders along the Jura range (limestone mountains) were used to map the altitude reached by the Rhone glacier during the two last glaciations. Precise mapping of crystalline and limestone boulders distribution also enabled mapping local Jura glaciers' recurrences after the Rhone glacier retreat. (2) During the last decades, several erratic boulders were used for cosmogenic nuclide exposure dating, which allowed impressive advances in palaeoclimatic research. (3) Erratic blocks have also an ecological interest by the fact that they "have transported" specific habitats in areas far away from their origin (e.g. acid crystalline rocks and soils in limestone areas such as in the Jura). For all these reasons, several erratic boulders were classified in the inventory of Swiss geosites. Erratic boulders also have a significant cultural value (Lugon et al., 2006). (1) The Glacier Garden in Lucerne was discovered in 1872. It comprises various surfaces of "roches moutonnées", potholes and large erratic blocks that document the presence of the Reuss glacier. Considered as a natural monument it is now one of the most famous touristic attraction of Lucerne and Central Switzerland. (2) The Pierre Bergère stone, situated in Salvan (Mont-Blanc massif, South-western Switzerland), is the place where future Nobel Prize

  3. NASA's Asteroid Redirect Mission: A Robotic Boulder Capture Option for Science, Human Exploration, Resource Utilization, and Planetary Defense

    Science.gov (United States)

    Abell, P.; Nuth, J.; Mazanek, D.; Merrill, R.; Reeves, D.; Naasz, B.

    2014-01-01

    boulder be returned for subsequent sampling. In addition, the material surrounding the boulder can be collected from the surface, thus providing geological contextual information and additional samples of NEA regolith. The robotic manipulators used for capturing the boulder will ensure some of the surface remains undisturbed and that the boulder will retain its structural integrity, which will preserve the context of any samples collected by the astronauts and ensure a high level of science return. Human Exploration: Due to the coherent nature of the boulder that will be collected, entire encapsulation of the asteroid material is not required. This facilitates exploration and sample collection of the boulder by astronauts in a variety of ways. The total time for EVA during the crew portion of the mission is very limited. Current estimates are that each of the two EVAs will only last four hours. The RBC option will allow crew members to have good situational awareness of the work site and quickly identify sample sites of interest. In addition, the samples to be collected can be readily accessed without having to deal with removal of an encapsulation system, which adds extra complexity and risk for the astronauts during EVA. Resource Utilization: One of the most crucial aspects for resource utilization is the identification and collection of appropriate materials (e.g., volatiles, organics, metals, etc.) that contain components of interest. Prior characterization of NEAs is required in order to increase the likelihood that appropriate materials will be returned. Ground-based observations of small (<10 m) NEAs are challenging, but characterization efforts of larger targets have demonstrated that NEAs with volatiles and organics have been identified. Two potential targets for the RBC option (Bennu and 1999 JU3) have been previously identified as potentially rich in resources, and both are already targets of currently planned robotic missions that will characterize their

  4. Predicted Versus Actual Savings for a Low-Rise Multifamily Retrofit in Boulder, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Arena, L. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Williamson, J. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2013-11-01

    To determine the most cost-effective methods of improving buildings, accurate analysis and prediction of the energy use of existing buildings is essential. However, multiple studies confirm that analysis methods tend to over-predict energy use in poorly insulated, leaky homes and thus, the savings associated with improving those homes. In this project, the Building America CARB team evaluated the retrofit of a multifamily building in Boulder, CO. The updated property is a 37 unit, 2 story apartment complex built in 1950, which underwent renovations in early 2009 to bring it into compliance with Boulder, CO's SmartRegs ordinance. Goals of the study were to: 1) evaluate predicted versus actual savings due to the improvements, 2) identify areas where the modeling assumptions may need to be changed, and 3) determine common changes made by renters that would negatively impact energy savings. Other issues that were investigated include the effects of improving building efficiency on tenant comfort, the impact on tenant turnover rates, and the potential market barriers for this type of community scale project.

  5. Early Implementation of Large Scale Carbon Dioxide Removal Projects through the Cement Industry

    Science.gov (United States)

    Zeman, F. S.

    2014-12-01

    The development of large-scale carbon dioxide reduction projects requires high purity CO2and a reactive cation source. A project seeking to provide both of these requirements will likely face cost barriers with current carbon prices. The cement industry is a suitable early implementation site for such projects by virtue of the properties of its exhaust gases and those of waste concrete. Cement plants are the second largest source of industrial CO2 emissions, globally. It is also the second largest commodity after water, has no ready substitute and is literally the foundation of society. Finally, half of the CO2 emissions originate from process reactions rather than fossil fuel combustion resulting in higher flue gas CO2concentrations. These properties, with the co-benefits of oxygen combustion, create a favorable environment for spatially suitable projects. Oxygen combustion involves substituting produced oxygen for air in a combustion reaction. The absence of gaseous N2 necessitates the recirculation of exhaust gases to maintain kiln temperatures, which increase the CO2 concentrations from 28% to 80% or more. Gas exit temperatures are also elevated (>300oC) and can reach higher temperatures if the multi stage pre-heater towers, that recover heat, are re-designed in light of FGR. A ready source of cations can be found in waste concrete, a by-product of construction and demolition activities. These wastes can be processed to remove cations and then reacted with atmospheric CO2 to produce carbonate minerals. While not carbon negative, they represent a demonstration opportunity for binding atmospheric CO2while producing a saleable product (precipitated calcium carbonate). This paper will present experimental results on PCC production from waste concrete along with modeling results for oxygen combustion at cement facilities. The results will be presented with a view to mineral sequestration process design and implementation.

  6. Accretion of Cometary Nuclei in the Solar Nebula: Boulders, Not Pebbles

    Science.gov (United States)

    Weissman, Paul R.; A'Hearn, Michael

    2015-11-01

    Comets are the most primitive bodies in the solar system. They retain a largely unprocessed record of conditions in the primordial solar nebula 4.56 Gyr ago, including the initial accretion of dust and ice particles into macroscopic bodies. Current accretion theory suggests that ice and dust aggregates grew to pebble (cm) sizes before streaming instabilities and gravitational collapse brought these pebble swarms together as km-sized (or larger) bodies. Recent imaging of the nucleus of comet 67P/Churyumov-Gerasimenko by the Rosetta OSIRIS camera team has revealed the existence of “goose bump” terrain on the nucleus surface and lining the interior walls of large, ~200 m diameter and 180 m deep cylindrical pits. These pits are believed to be sinkholes, formed when near-surface materials collapse into voids within the nucleus, revealing the fresh comet interior on the walls of the pits. The goose bump terrain consists of 3-4 m diameter “boulders” randomly stacked one on top of another. We propose that these boulders, likely with an icy-conglomerate composition, are the basic building blocks of cometary nuclei. This is the first observational confirmation of current accretion theories, with the caveat that rather than pebbles, the preferred size range is 3-4 m boulders for objects formed in the giant planets region of the solar system. The presence of icy grains beyond the solar nebula snow-line and the large heliocentric range of the giant planets region likely contribute to the formation of these larger boulders, before they are incorporated into cometary nuclei. This work was supported by NASA through the U.S. Rosetta Project.

  7. NASA’s Asteroid Redirect Mission: The Boulder Capture Option

    Science.gov (United States)

    Abell, Paul; Nuth, Joseph A.; Mazanek, Dan D.; Merrill, Raymond G.; Reeves, David M.; Naasz, Bo J.

    2014-11-01

    NASA is examining two options for the Asteroid Redirect Mission (ARM), which will return asteroid material to a Lunar Distant Retrograde Orbit (LDRO) using a robotic solar-electric-propulsion spacecraft, called the Asteroid Redirect Vehicle (ARV). Once the ARV places the asteroid material into the LDRO, a piloted mission will rendezvous and dock with the ARV. After docking, astronauts will conduct two extravehicular activities (EVAs) to inspect and sample the asteroid material before returning to Earth. One option involves capturing an entire small (˜4-10 m diameter) near-Earth asteroid (NEA) inside a large inflatable bag. However, NASA is examining another option that entails retrieving a boulder (˜1-5 m) via robotic manipulators from the surface of a larger (˜100+ m) pre-characterized NEA. This option can leverage robotic mission data to help ensure success by targeting previously (or soon to be) well-characterized NEAs. For example, the data from the Hayabusa mission has been utilized to develop detailed mission designs that assess options and risks associated with proximity and surface operations. Hayabusa’s target NEA, Itokawa, has been identified as a valid target and is known to possess hundreds of appropriately sized boulders on its surface. Further robotic characterization of additional NEAs (e.g., Bennu and 1999 JU3) by NASA’s OSIRIS REx and JAXA’s Hayabusa 2 missions is planned to begin in 2018. The boulder option is an extremely large sample-return mission with the prospect of bringing back many tons of well-characterized asteroid material to the Earth-Moon system. The candidate boulder from the target NEA can be selected based on inputs from the world-wide science community, ensuring that the most scientifically interesting boulder be returned for subsequent sampling. This boulder option for NASA’s ARM can leverage knowledge of previously characterized NEAs from prior robotic missions, which provides more certainty of the target NEA

  8. Metal contamination and post-remediation recovery in the Boulder River watershed, Jefferson County, Montana

    Science.gov (United States)

    Unruh, D.M.; Church, S.E.; Nimick, D.A.; Fey, D.L.

    2009-01-01

    The legacy of acid mine drainage and toxic trace metals left in streams by historical mining is being addressed by many important yet costly remediation efforts. Monitoring of environmental conditions frequently is not performed but is essential to evaluate remediation effectiveness, determine whether clean-up goals have been met, and assess which remediation strategies are most effective. Extensive pre- and post-remediation data for water and sediment quality for the Boulder River watershed in southwestern Montana provide an unusual opportunity to demonstrate the importance of monitoring. The most extensive restoration in the watershed occurred at the Comet mine on High Ore Creek and resulted in the most dramatic improvement in aquatic habitat. Removal of contaminated sediment and tailings, and stream-channel reconstruction reduced Cd and Zn concentrations in water such that fish are now present, and reduced metal concentrations in streambed sediment by a factor of c. 10, the largest improvement in the district. Waste removals at the Buckeye/Enterprise and Bullion mine sites produced limited or no improvement in water and sediment quality, and acidic drainage from mine adits continues to degrade stream aquatic habitat. Recontouring of hillslopes that had funnelled runoff into the workings of the Crystal mine substantially reduced metal concentrations in Uncle Sam Gulch, but did not eliminate all of the acidic adit drainage. Lead isotopic evidence suggests that the Crystal mine rather than the Comet mine is now the largest source of metals in streambed sediment of the Boulder River. The completed removal actions prevent additional contaminants from entering the stream, but it may take many years for erosional processes to diminish the effects of contaminated sediment already in streams. Although significant strides have been made, additional efforts to seal draining adits or treat the adit effluent at the Bullion and Crystal mines would need to be completed to

  9. Efficient gradient projection methods for edge-preserving removal of Poisson noise

    Science.gov (United States)

    Zanella, R.; Boccacci, P.; Zanni, L.; Bertero, M.

    2009-04-01

    Several methods based on different image models have been proposed and developed for image denoising. Some of them, such as total variation (TV) and wavelet thresholding, are based on the assumption of additive Gaussian noise. Recently the TV approach has been extended to the case of Poisson noise, a model describing the effect of photon counting in applications such as emission tomography, microscopy and astronomy. For the removal of this kind of noise we consider an approach based on a constrained optimization problem, with an objective function describing TV and other edge-preserving regularizations of the Kullback-Leibler divergence. We introduce a new discrepancy principle for the choice of the regularization parameter, which is justified by the statistical properties of the Poisson noise. For solving the optimization problem we propose a particular form of a general scaled gradient projection (SGP) method, recently introduced for image deblurring. We derive the form of the scaling from a decomposition of the gradient of the regularization functional into a positive and a negative part. The beneficial effect of the scaling is proved by means of numerical simulations, showing that the performance of the proposed form of SGP is superior to that of the most efficient gradient projection methods. An extended numerical analysis of the dependence of the solution on the regularization parameter is also performed to test the effectiveness of the proposed discrepancy principle.

  10. Asteroid Redirect Robotic Mission: Robotic Boulder Capture Option Overview

    Science.gov (United States)

    Mazanek, Daniel D.; Merrill, Raymond G.; Belbin, Scott P.; Reeves, David M.; Earle, Kevin D.; Naasz, Bo J.; Abell, Paul A.

    2014-01-01

    The National Aeronautics and Space Administration (NASA) is currently studying an option for the Asteroid Redirect Robotic Mission (ARRM) that would capture a multi-ton boulder (typically 2-4 meters in size) from the surface of a large (is approximately 100+ meter) Near-Earth Asteroid (NEA) and return it to cislunar space for subsequent human and robotic exploration. This alternative mission approach, designated the Robotic Boulder Capture Option (Option B), has been investigated to determine the mission feasibility and identify potential differences from the initial ARRM concept of capturing an entire small NEA (4-10 meters in size), which has been designated the Small Asteroid Capture Option (Option A). Compared to the initial ARRM concept, Option B allows for centimeter-level characterization over an entire large NEA, the certainty of target NEA composition type, the ability to select the boulder that is captured, numerous opportunities for mission enhancements to support science objectives, additional experience operating at a low-gravity planetary body including extended surface contact, and the ability to demonstrate future planetary defense strategies on a hazardous-size NEA. Option B can leverage precursor missions and existing Agency capabilities to help ensure mission success by targeting wellcharacterized asteroids and can accommodate uncertain programmatic schedules by tailoring the return mass.

  11. Project WAGR: The UK demonstration project for power reactor decommissioning - removing the core and looking to completion

    Energy Technology Data Exchange (ETDEWEB)

    Benest, T. G. [United Kingdom Atomic Energy Authority, Headquarters, London (United Kingdom)

    2003-07-01

    The United Kingdom Atomic Energy Authority (UKAEA) has built and operated a wide range of nuclear facilities since the late 1940's. UKAEA's present mission is to restore the environment of these facilities in a safe and environmentally responsible manner. This restoration includes the decommissioning of a number of redundant research and power reactors, one of which is the Windscale Advanced Gas-cooled Reactor (WAGR). Following shut down, UKAEA decided to continue the prototype function of the reactor into the decommissioning phase to develop dismantling techniques and establish waste routes. The reactor core and pressure vessel are now being dismantled in a programme of 10 campaigns, seven of which have been completed since 1998. It is anticipated that the current programme will be completed by summer 2005. This paper outlines the history of the reactor, the operation of the waste-processing route, the installed dismantling equipment and the successful completion of the first seven campaigns. This earlier work has been described in a number of publications and conferences, so this paper concentrates on recent work to select and develop cutting equipment to dismantle the core support structures and the pressure vessel. The decommissioning of the Windscale Advance Gas-cooled reactor is being undertaken to demonstrate that a power reactor can be decommissioned shortly after shutdown. The removal of the core and pressure vessel has been broken down into a series of 10 campaigns associated with particular core components. The first 7 campaigns have been successfully completed and the 8., is expected to commence in September 2003 17 months earlier than planned. Dismantling methodologies and tools have been developed specifically for each of these campaigns. Full-scale mock-ups have been used to test the tools, train the operators and assess the duration of operations. However, despite successful trials, operational experience has shown that some of these tools

  12. Arsenic Removal from Drinking Water by Adsorptive Media U.S. EPA Demonstration Project at Richmond Elementary School in Susanville, CA Final Performance Evaluation Report

    Science.gov (United States)

    This report documents the activities performed and the results obtained for the arsenic removal treatment technology demonstration project at Richmond Elementary School in Susanville, CA. The objectives of the project were to evaluate: (1) the effectiveness of an Aquatic Treatme...

  13. NASA's asteroid redirect mission: Robotic boulder capture option

    Science.gov (United States)

    Abell, P.; Nuth, J.; Mazanek, D.; Merrill, R.; Reeves, D.; Naasz, B.

    2014-07-01

    NASA is examining two options for the Asteroid Redirect Mission (ARM), which will return asteroid material to a Lunar Distant Retrograde Orbit (LDRO) using a robotic solar-electric-propulsion spacecraft, called the Asteroid Redirect Vehicle (ARV). Once the ARV places the asteroid material into the LDRO, a piloted mission will rendezvous and dock with the ARV. After docking, astronauts will conduct two extravehicular activities (EVAs) to inspect and sample the asteroid material before returning to Earth. One option involves capturing an entire small (˜4--10 m diameter) near-Earth asteroid (NEA) inside a large inflatable bag. However, NASA is also examining another option that entails retrieving a boulder (˜1--5 m) via robotic manipulators from the surface of a larger (˜100+ m) pre-characterized NEA. The Robotic Boulder Capture (RBC) option can leverage robotic mission data to help ensure success by targeting previously (or soon to be) well-characterized NEAs. For example, the data from the Japan Aerospace Exploration Agency's (JAXA) Hayabusa mission has been utilized to develop detailed mission designs that assess options and risks associated with proximity and surface operations. Hayabusa's target NEA, Itokawa, has been identified as a valid target and is known to possess hundreds of appropriately sized boulders on its surface. Further robotic characterization of additional NEAs (e.g., Bennu and 1999 JU_3) by NASA's OSIRIS REx and JAXA's Hayabusa 2 missions is planned to begin in 2018. This ARM option reduces mission risk and provides increased benefits for science, human exploration, resource utilization, and planetary defense.

  14. ATS6 radio beacon electron content measurements at Boulder, July 1974--May 1975

    International Nuclear Information System (INIS)

    Routine monitoring of the plasmaspheric content was a primary objective of the ATS6 Radio Beacon Experiment (RBE) and this set critical requirements on transmitter and receiver stabilities. The satellite transmitted linearly polarized signals on carrier frequencies of 40.016, 140.056, and 360.144 MHz, with modulations of 100.04 kHz and 1.004 MHz. This provided coarse and fine scales of measurements so that the cycle ambiguity in the phase measurements of both Faraday rotation and group delay could be resolved. This report summarizes 140 MHz data recorded at the Boulder, Colorado, ground station (40.13 degrees N, 105.24 degrees W) while ATS6 was positioned above 94 degrees west longitude, between July 1974 and May 1975. The satellite appeared at an azimuth of 163 degrees, elevation 42 degrees, with the projection of the ray path near the ground. All data were digitally recorded once per second

  15. Clast mobility within boulder beaches over two winters in Galicia, northwestern Spain

    Science.gov (United States)

    Pérez-Alberti, Augusto; Trenhaile, Alan S.

    2015-11-01

    A micro-drone was used to make low altitude flights over boulder beaches at Laxe Brava and Oia in Galicia, northwestern Spain. Flights were made in July 2012, May 2013, and spring 2014. High resolution digital terrain models and orthophotographs, combined with GIS mapping, were used to monitor changes in the position of thousands of boulders. Maximum storm wave height was higher in the winter of 2013-2014 than in winter 2012-2013, and this was reflected in an increase in the proportion of the boulders that moved in the two winters, from 17% to almost 48% at Laxe Brava, and from 53% to almost 88% at Oia. The greater mobility of the boulders at Oia can be attributed in part to their generally smaller size, although there was considerable overlap between the size of boulders that moved and those that did not move within and between the two beaches. There were mobile boulders in areas up to several metres above the high tidal level on both beaches, and boulder transport in the shore-normal and alongshore directions triggered some changes in the beach profiles, particularly in the middle to upper parts of the beaches. Estimates of threshold transport conditions, scaled to boulder mass, breaker height, and other variables, suggested that all but the very largest boulders on the two beaches should have been mobile, even during the summer months when the waves were much lower than in winter. Model over-prediction can be attributed to a number of factors, including: constraints on movement imposed by surrounding boulders; differences in boulder size and their effect on pivoting angles and on the degree to which boulders are exposed or sheltered from wave impact; and difficulties in assigning appropriate values to model coefficients.

  16. The Impact of the Actinide Removal Process (ARP) on the SB4 Projected Operating Windows

    Energy Technology Data Exchange (ETDEWEB)

    Peeler, D

    2005-03-05

    The model-based assessments of nominal Sludge Batch 4 (SB4) compositions suggest that a viable frit candidate does not appear to be a limiting factor as the Closure Business Unit (CBU) considers various tank blending options for SB4 with or without the Actinide Removal Process (ARP) streams. This statement is based solely on the projected operating windows derived from model predictions and does not include experimental assessments of SO{sub 4} solubility or melt rate issues. To assess the impact of the various ARP options on the projected operating windows, the 1100 canister SB4 baseline options served as the technical baseline or reference point for the comparisons. With respect to the various ARP options being considered, the impacts to the projected operating windows were relatively consistent with the impacts being dependent upon the property limiting access to higher WLs. More specifically, for those 1100 canister SB4 systems (without ARP) which were T{sub L}-limited, the general impact was an increase in the upper WL which was classified as acceptable resulting in an overall increase in the operating window size. The anticipated negative impact of TiO{sub 2} (due to an assumed increase in T{sub L} which would further reduce the size of the operating window of such systems) was not observed. The hypothesis is that the negative impact was countered or compensated by a positive impact due to the additional Na{sub 2}O from the ARP process. The overall result was a net increase in the size of the operating window for the SB4 1100 canister options which were T{sub L}-limited. This trend was observed for all five ARP options with the only difference being the magnitude of the increase (ranging from a 1%-4% increase) which was strictly based on the specific ARP composition and blending strategy. Another general observation for all five ARP options was a negative impact with their addition to a 1100 canister system that was initially low viscosity limited or

  17. Development of margin assessment methodology of decay heat removal function against external hazards. (1) Project overview and snow PRA methodology

    International Nuclear Information System (INIS)

    This paper describes mainly snow probabilistic risk assessment (PRA) methodology development in addition to the project overview. This project addresses extreme weathers (snow, tornado, wind and rainfall), volcanic phenomena and forest fire as representative external hazards. In this project, the methodologies of both PRA and margin assessment are developed for each external hazard through external hazard and accident sequence evaluations mainly in terms of decay heat removal function of a sodium-cooled fast reactor (SFR). Using recent 50 year weather data at a typical Japanese SFR site, snow hazard categories were set the combination of daily snowfall depth (snowfall speed) and snowfall duration which can be calculated by dividing the snow depth by the snowfall speed. For each snow hazard category, the accident sequence was evaluated by producing event trees which consist of several headings representing the loss of decay heat removal. Snow removal action and manual operation of the air cooler dampers were introduced into the event tree as accident managements. In this paper, the snow PRA showed less than 10-6/reactor-year of core damage frequency. The dominant snow hazard category was the combination of 1−2 m/day of snowfall speed and 0.5−0.75 day of snowfall duration. Importance and sensitivity analyses indicated a high risk contribution to secure the access routes. (author)

  18. Advanced Product Water Removal and Management (APWR) Fuel Cell System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation is a passive, self-regulating, gravity-independent Advanced Product Water Removal (APWR) system for Polymer Electrolyte Membrane (PEM)...

  19. Advanced Product Water Removal and Management (APWR) Fuel Cell System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation is a passive, self-regulating, gravity-independent Advanced Product Water Removal and management (APWR) system for incorporation into...

  20. Removing Mid-Spatial Frequency (MSF) Errors Using Stress-Polishing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This IRAD proposes to evaluate how stress polishing can be used to extend the application of super-polishing to fast aspheres and freeforms, removing sub-aperture...

  1. Bio-Electrochemical Carbon Dioxide Removal for Air Revitalization in Exploration Life Support Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — An important aspect of the ISS air revitalization system for life support is the removal of carbon dioxide from cabin air and retrieves oxygen from CO2. The current...

  2. Removing Mid-Spatial Frequency Errors on Curved Surfaces with VIBE Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Optimax VIBE process is a full-aperture, conformal polishing process incorporating high frequency motion that rapidly removes sub-surface damage in a VIBE...

  3. Novel Conductive Water Removal Membrane (CWRM) for PEM Passive Fuel Cell Operation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ElectroChem proposes a Phase II program to advance its Phase I effort, to develop a conductive water removal membrane to enable passive, high current density PEMFC...

  4. Predicted Versus Actual Savings for a Low-Rise Multifamily Retrofit in Boulder, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Arena, L.; Williamson, J.

    2013-11-01

    To determine the most cost-effective methods of improving buildings, accurate analysis and prediction of the energy use of existing buildings is essential. However, multiple studies confirm that analysis methods tend to over-predict energy use in poorly insulated, leaky homes and thus, the savings associated with improving those homes. In NREL's report titled 'Assessing and Improving the Accuracy of Energy Analysis of Residential Buildings,' researchers propose a method for improving the accuracy of residential energy analysis methods. A key step in this process involves the comparisons of predicted versus metered energy use and savings. In support of this research need, CARB evaluated the retrofit of a multifamily building in Boulder, CO. The updated property is a 37 unit, 2 story apartment complex built in 1950, which underwent renovations in early 2009 to bring it into compliance with Boulder, CO's SmartRegs ordinance. Goals of the study were to: 1) evaluate predicted versus actual savings due to the improvements, 2) identify areas where the modeling assumptions may need to be changed, and 3) determine common changes made by renters that would negatively impact energy savings. In this study, CARB seeks to improve the accuracy of modeling software while assessing retrofit measures to specifically determine which are most effective for large multifamily complexes in the cold climate region. Other issues that were investigated include the effects of improving building efficiency on tenant comfort, the impact on tenant turnover rates, and the potential market barriers for this type of community scale project.

  5. ALARA plan for the Old Hydrofracture Facility tanks contents removal project at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    The purpose of the Old Hydrofracture Facility (OHF) Tanks Contents Removal Project is to remove the liquid low-level waste from the five underground storage tanks located at OHF and transfer the resulting slurry to the Melton Valley Storage Tanks facility for treatment and disposal. Among the technical objectives for the OHF Project, there is a specific provision to maintain personnel exposures as low as reasonably achievable (ALARA) during each activity of the project and to protect human health and the environment. The estimated doses and anticipated conditions for accomplishing this project are such that an ALARA Plan is necessary to facilitate formal radiological review of the campaign. This ALARA Plan describes the operational steps necessary for accomplishing the job together with the associated radiological impacts and planned controls. Individual and collective dose estimates are also provided for the various tasks. Any significant changes to this plan (i.e., planned exposures that are greater than 10% of original dose estimates) will require formal revision and concurrence from all parties listed on the approval page. Deviations from this plan (i.e., work outside the scope covered by this plan) also require the preparation of a task-specific ALARA Review that will be amended to this plan with concurrence from all parties listed on the approval page

  6. Inventory and projections of UK emissions by sources and removals by sinks due to land use, land use change and forestry. Annual report July 2009

    OpenAIRE

    Dyson, K.E.; Thomson, A. M.; Mobbs, D.C.; Milne, R; U. Skiba; Clark, A; P. E. Levy; Jones, S. K.; M. F. Billett; Dinsmore, K. J.; Oijen, M. van; N. Ostle; Foeried, B.; Smith, P.; Matthews, R. W.

    2009-01-01

    The overall aim of the project id to produce inventories and projections of UK greenhouse gas emissions by sources and removals by sinks due to land use, land use change and forestry (LULUCF). The project report contains the methods and numbers for these inventories and progress reports on the science undertaken to support and develop the inventory.

  7. Inventory and projections of UK emissions by sources and removals by sinks due to land use, land use change and forestry. Annual Report June 2007

    OpenAIRE

    Thomson, A. M.; Mobbs, D.C.; Milne, R; U. Skiba; P. E. Levy; Jones, S. K.; M. F. Billett; Oijen, M. van; N. Ostle; Foereid, B.; Smith, P.; Randle, T.; Matthews, R. W.; Gilbert, J; Halsall, L.

    2007-01-01

    The overall aim of the project is to produce inventories and projections of UK greenhouse gas emissions by sources and removals by sinks due to Land Use, Land USe Change and Forestry (LULUCF). The project report contains the methods and numbers for these inventories and progress reports on the science undertaken to support and develop the inventory.

  8. Geomorphic Analysis of Boulder Volumes and Surface Roughness Along Talus Slopes in Yosemite Valley, California

    Science.gov (United States)

    Takahashi, K.; Stock, G. M.; Finnegan, N. J.

    2015-12-01

    Talus slopes in Yosemite Valley, California, are a rich archive of rock fall processes occurring since deglaciation (~ 15 ka). The valley is an ideal natural laboratory for investigating rock fall processes because the cliffs display a wide range of heights, steepnesses, orientations, and granitic lithologies. We measured the spatial distribution of boulder volumes on rock fall-dominated talus slopes along 10 transects at 8 locations in Yosemite Valley. Boulder volumes span 6 orders of magnitude, from 0.003 to 3000 m3. As expected, boulder volumes increase non-linearly downslope, with the largest boulders located at or beyond the base of talus slopes. Boulder volumes are smaller below cliffs composed of more mafic lithologies, likely reflecting the greater fracture density in those cliffs. Moderately tall cliffs (400-550 m) tend to produce larger boulders than the tallest and shortest cliffs. Using airborne lidar data, we calculated talus surface roughness and found modest increases in roughness as a function of downslope distance, likely related to the downslope increase in boulder volume. By quantifying the spatial distribution of boulder volumes, our results can be used to improve future assessments of rockfall hazard adjacent to talus slopes.

  9. 75 FR 77898 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2010-12-14

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY... of human remains in the possession of the ] University of Colorado Museum, Boulder, CO. The human... CFR 10.11(d). The determinations in this notice are the sole responsibility of the museum,...

  10. 75 FR 28647 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2010-05-21

    ... Tribe, Crow Tribe, Fort Belknap Indian Community, and Three Affiliated Tribes (73 FR 8359-8360, February... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY... of human remains in the possession of the University of Colorado Museum, Boulder, CO. The...

  11. 75 FR 45657 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2010-08-03

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY... of human remains in the control of the University of Colorado Museum, Boulder, CO. The human remains... notice are the sole responsibility of the museum, institution, or Federal agency that has control of...

  12. 75 FR 45655 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2010-08-03

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY... of human remains in the control of the University of Colorado Museum, Boulder, CO. The human remains... sole responsibility of the museum, institution, or Federal agency that has control of the...

  13. Size-frequency distribution of boulders ≥10 m on comet 103P/Hartley 2

    Science.gov (United States)

    Pajola, Maurizio; Lucchetti, Alice; Bertini, Ivano; Marzari, Francesco; A'Hearn, Michael F.; La Forgia, Fiorangela; Lazzarin, Monica; Naletto, Giampiero; Barbieri, Cesare

    2016-01-01

    Aims: We derive the size-frequency distribution of boulders on comet 103P/Hartley 2, which are computed from the images taken by the Deep Impact/HRI-V imaging system. We indicate the possible physical processes that lead to these boulder size distributions. Methods: We used images acquired by the High Resolution Imager-Visible CCD camera on 4 November 2010. Boulders ≥10 m were identified and manually extracted from the datasets with the software ArcGIS. We derived the global size-frequency distribution of the illuminated side of the comet (~50%) and identified the power-law indexes characterizing the two lobes of 103P. The three-pixel sampling detection, together with the shadowing of the surface, enables unequivocally detection of boulders scattered all over the illuminated surface. Results: We identify 332 boulders ≥10 m on the imaged surface of the comet, with a global number density of nearly 140/km2 and a cumulative size-frequency distribution represented by a power law with index of -2.7 ± 0.2. The two lobes of 103P show similar indexes, i.e., -2.7 ± 0.2 for the bigger lobe (called L1) and -2.6+ 0.2/-0.5 for the smaller lobe (called L2). The similar power-law indexes and similar maximum boulder sizes derived for the two lobes both point toward a similar fracturing/disintegration phenomena of the boulders as well as similar lifting processes that may occur in L1 and L2. The difference in the number of boulders per km2 between L1 and L2 suggests that the more diffuse H2O sublimation on L1 produce twice the boulders per km2 with respect to those produced on L2 (primary activity CO2 driven). The 103P comet has a lower global power-law index (-2.7 vs. -3.6) with respect to 67P. The global differences between the two comets' activities, coupled with a completely different surface geomorphology, make 103P hardly comparable to 67P. A shape distribution analysis of boulders ≥30 m performed on 103P suggests that the cometary boulders show more elongated shapes

  14. Large-scale dam removal in the northeast United States: documenting ecological responses to the Penobscot River Restoration Project

    Science.gov (United States)

    Collins, M. J.; Aponte Clarke, G.; Baeder, C.; McCaw, D.; Royte, J.; Saunders, R.; Sheehan, T.

    2012-12-01

    The Penobscot River Restoration Project aims to improve aquatic connectivity in New England's second largest watershed ( 22,000 km2) by removing the two lowermost, mainstem dams and bypassing a third dam on a principal tributary upstream. Project objectives include: restoring unobstructed access to the entire historic riverine range for five lower river diadromous species including Atlantic and shortnose sturgeon; significantly improving access to upstream habitat for six upper river diadromous species including Atlantic salmon; reconnecting trophic linkages between headwater areas and the Gulf of Maine; restoring fluvial processes to the former impoundments; improving recreational and Penobscot Nation cultural opportunities; and maintaining basin-wide hydropower output. The project is expected to have landscape-scale benefits and the need for a significant investment in long-term monitoring and evaluation to formally quantify ecosystem response has been recognized. A diverse group of federal, state, tribal, NGO, and academic partners has developed a long-term monitoring and evaluation program composed of nine studies that began in 2009. Including American Recovery and Reinvestment Act (ARRA) funding that leveraged partner contributions, we have invested nearly $2M to date in pre- and post-removal investigations that evaluate geomorphology/bed sediment, water quality, wetlands, and fisheries. Given the number of affected diadromous species and the diversity of their life histories, we have initiated six distinct, but related, fisheries investigations to document these expected changes: Atlantic salmon upstream and downstream passage efficiency using passive integrated transponder (PIT) and acoustic telemetry; fish community structure via an index of biotic integrity (IBI); total diadromous fish biomass through hydroacoustics; shortnose sturgeon spawning and habitat use via active and passive acoustic telemetry; and freshwater-marine food web interactions by

  15. Boulders on asteroid Toutatis as observed by Chang'e-2

    CERN Document Server

    Jiang, Yun; Huang, Jiangchuan; Marchi, Simone; Li, Yuan; Ip, Wing-Huen

    2015-01-01

    Boulders are ubiquitously found on the surfaces of small rocky bodies in the inner solar system and their spatial and size distributions give insight into the geological evolution and collisional history of the parent bodies. Using images acquired by the Chang'e-2 spacecraft, more than 200 boulders have been identified over the imaged area of the near-Earth asteroid Toutatis. The cumulative boulder size frequency distribution (SFD) shows a steep slope of -4.4 $\\pm$ 0.1, which is indicative of a high degree of fragmentation. Similar to Itokawa, Toutatis probably has a rubble-pile structure, as most boulders on its surface cannot solely be explained by impact cratering. The significantly steeper slope for Toutatis' boulder SFD compared to Itokawa may imply a different preservation state or diverse formation scenarios. In addition, the cumulative crater SFD has been used to estimate a surface crater retention age of approximately 1.6 $\\pm$ 0.3 Gyr.

  16. Cold test plan for the Old Hydrofracture Facility tank contents removal project, Oak Ridge National Laboratory, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    This Old Hydrofracture Facility (OHF) Tanks Contents Removal Project Cold Test Plan describes the activities to be conducted during the cold test of the OHF sluicing and pumping system at the Tank Technology Cold Test Facility (TTCTF). The TTCTF is located at the Robotics and Process Systems Complex at the Oak Ridge National Laboratory (ORNL). The cold test will demonstrate performance of the pumping and sluicing system, fine-tune operating instructions, and train the personnel in the actual work to be performed. After completion of the cold test a Technical Memorandum will be prepared documenting completion of the cold test, and the equipment will be relocated to the OHF site.

  17. Compliance Monitoring of Underwater Blasting for Rock Removal at Warrior Point, Columbia River Channel Improvement Project, 2009/2010

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, Thomas J.; Johnson, Gary E.; Woodley, Christa M.; Skalski, J. R.; Seaburg, Adam

    2011-05-10

    The U.S. Army Corps of Engineers, Portland District (USACE) conducted the 20-year Columbia River Channel Improvement Project (CRCIP) to deepen the navigation channel between Portland, Oregon, and the Pacific Ocean to allow transit of fully loaded Panamax ships (100 ft wide, 600 to 700 ft long, and draft 45 to 50 ft). In the vicinity of Warrior Point, between river miles (RM) 87 and 88 near St. Helens, Oregon, the USACE conducted underwater blasting and dredging to remove 300,000 yd3 of a basalt rock formation to reach a depth of 44 ft in the Columbia River navigation channel. The purpose of this report is to document methods and results of the compliance monitoring study for the blasting project at Warrior Point in the Columbia River.

  18. Removal of radon by aeration testing of various aeration techniques for small water works. For European Commission under Contract No FI4PCT960054 TENAWA project

    CERN Document Server

    Salonen, L; Mehtonen, J; Mjoenes, L; Raff, O; Turunen, H

    2002-01-01

    Capability of various aeration techniques to remove radon from water in small waterworks was studied as a part of project (Treatment Techniques for Removing Natural Radionuclides from Drinking Water), which was carried out during 1997-1999 on a cost-shared basis (contract No. F14PCT960054) with The European Commission (CEC) under the supervision of the Directorate-General XII Radiation Protection Research Unit. In TENAWA project both laboratory and field experiments were performed in order to find reliable methods and equipment for removing natural radionuclides from ground water originating either from private wells or small waterworks. Because such techniques are more often needed in private households than at waterworks, the main emphasis of the research was aimed to solve the water treatment problems related to the private water supplies, especially bedrock wells. Radon was the most important radionuclide to be removed from water at waterworks whereas the removal of other radionuclides ( sup 2 sup 3 sup 4...

  19. ARSENIC REMOVAL FROM DRINKING WATER BY POINT OF USE REVERSE OSMOSIS. EPA DEMONSTRATION PROJECT AT SUNSET RANCH DEVELOPMENT IN HOMEDALE, ID. SIX-MONTH EVALUATION REPORT

    Science.gov (United States)

    This report documents the activities performed during and the results obtained from the first six months of the point of use arsenic removal treatment technology demonstration project at the Sunset Ranch Development in Homedale, ID. The objectives of the project are to evaluate t...

  20. Arsenic Removal from Drinking Water by Adsorptive Media - U.S. EPA Demonstration Project at Woodstock Middle School in Woodstock, CT - Final Performance Evaluation Report

    Science.gov (United States)

    This report documents the activities performed for and the results obtained from the arsenic removal treatment technology demonstration project at the Woodstock Middle School in Woodstock, CT. The objectives of the project were to evaluate the effectiveness of Adsorbsia™ GTO™ me...

  1. Arsenic Removal from Drinking Water by Adsorptive Media U.S. EPA Demonstration Project at Webb Consolidated Independent School District in Bruni, TX - Final Performance Evaluation Report

    Science.gov (United States)

    This report documents the activities performed and the results obtained from the arsenic removal treatment technology demonstration project at the Webb Consolidated Independent School District (Webb CISD) in Bruni, TX. The main objective of the project was to evaluate the effect...

  2. Sedimentary processes associated with sand and boulder deposits formed by the 2011 Tohoku-oki tsunami at Sabusawa Island, Japan

    Science.gov (United States)

    Goto, Kazuhisa; Sugawara, Daisuke; Ikema, Satoko; Miyagi, Toyohiko

    2012-12-01

    This paper reports on the sedimentary processes of sand and boulder deposition at Sabusawa Island, Japan as a result of the 2011 Tohoku-oki tsunami. Boulders were composed of tuffaceous rocks and sourced from an earthquake-triggered slope failure as well as concrete fragments of seawall. They were scattered over the ground surface and did not form boulder ridges, although there was some local imbrication. The boulders were deposited on top of a sand layer indicating that the latter, possibly deposited from bed load, covered the ground surface first. This sand layer probably reduced friction allowing boulders to be transported more easily than might be expected across a hard ground with a high bottom friction. Sand deposits showed landward thinning and fining features, while the boulders showed a landward coarsening (tuffaceous boulders) or a landward fining (concrete boulders), indicating that large clasts were not necessarily scattered randomly but rather might have a clast size gradient with distance inland. These features are explained by the local topographic setting that constrained the directions of incoming and returning tsunami flows. Some clasts at the inland extent of the boulder field were covered by an upward fining sand layer. This feature suggests that the boulders were deposited prior to the suspended sands, with the latter subsequently laid down before the water level dropped below the top of the boulders. Such modern investigations of the sedimentary features of various sizes of grains and clasts immediately after a tsunami provide invaluable data for the reconstruction of inundation processes.

  3. Measured and Inferred Bedrock Faults in the Boulder-Weld Coal Field (frifaultu)

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This file is a digital line representation of measured and inferred bedrock faults in the Boulder-Weld coal field, Denver Basin, Colorado. This file was created as...

  4. Twin image removal in digital in-line holography based on iterative inter-projections

    Science.gov (United States)

    Chen, Bing Kuan; Chen, Tai-Yu; Hung, Shau Gang; Huang, Sheng-Lung; Lin, Jiunn-Yuan

    2016-06-01

    A simple and efficient phase retrieval method based on the iterative inter-projections of the recorded Fourier modulus between two effective holographic planes is developed to eliminate the twin image in digital in-line holography. The proposed algorithm converges stably in phase extraction procedures without requiring any prior knowledge or sophisticated support of the object and is applicable to lensless Gabor and Fourier holography as well as holographic microscopy with imaging lenses. Numerical and experimental results suggest that the spatial resolution enhancement on the reconstructed image can be achieved with this technique due to the capability of recovering the diffraction phases of low-intensity signals.

  5. A method to remove the projection error in triple-energy radiography with contrast medium

    Science.gov (United States)

    Baldazzi, G.; Lanconelli, N.; Masetti, S.; Fiaschetti, M.; Maccagnani, M.; Roma, L.; Rossi, P. L.; Levi, G.; Sbarra, C.

    2009-10-01

    The density-map reconstruction of a radiological contrast medium is affected by noise arising from the background lack of homogeneity (the so-called "projection error") if images of the medium are collected starting from quasi-monochromatic X-ray beams. This noise, especially for a dual-energy reconstruction algorithm, becomes more significant than the statistical fluctuations of the photon-transmitted flux, dramatically reducing the accuracy and the sensitivity of the reconstruction. In this work, we investigate the efficacy of the triple-energy technique, which is based on the simultaneous acquisition of three monochromatic images of the same target injected with contrast medium. A theoretical analysis allows to estimate the sensitivity and the accuracy of the reconstructed density map compared with the dual-energy one (i.e., the density map reconstructed acquiring only two monochromatic images). To validate the theory, a set of experimental measurements was performed: results show that triple energy drastically reduces the projection errors (from 10 to 60 times smaller than the dual-energy one), making it negligible with respect to the statistical noise.

  6. Shallow Geophysical Exploration of the Boulder Creek Critical Zone Observatory

    Science.gov (United States)

    Befus, K. M.; Kelsay, T.; Sheehan, A. F.; Leopold, M.

    2009-12-01

    We use minimally invasive shallow geophysical techniques to image the structure of the critical zone from surface to bedrock (0-20 m) throughout three catchments within the Boulder Creek Critical Zone Observatory (BcCZO). Shallow seismic refraction (SSR), electrical resistivity tomography (ERT) and ground penetrating radar (GPR) provide three complementary methods for determining the physical characteristics of the shallow subsurface. A total of 10 km of SSR surveys were collected in Summer 2009 using a hammer source and 24-channel seismograph. The SSR data were modeled using both the time-term method and travel-time tomography. Results of the SSR surveys provide a pseudo-3D network of critical zone compressional wave velocity (Vp) structure within each catchment. Select SSR lines follow each of the ERT and GPR lines investigated providing an essential supplement for interpretation and view of layering within the critical zone. The evolution of each catchment within the BcCZO contain signals of both erosion and weathering dependent upon the large-scale geomorphic processes down to the microbial weathering of mineral grains. The geophysical approach describes the arena for the small-scale processes while also providing a quantitative description of the critical zone structure at an instant in time. We use these tools to establish a three-dimensional model of critical zone architecture within three catchments with significantly different recent and continuing geomorphic forcings: fluvial rejuvenation, long-term quiescent erosion and glaciation. We find bedrock Vp greater than 2500 m/s, regolith Vp generally less than 450 m/s and various gradients of weathered bedrock ranging from Vp of 700-2000 m/s if present. Significant topography and irregular bedrock surfaces contribute additional complexity to the critical zone architecture in each location. Once developed this model will guide investigations of critical zone processes from landscape to hydrologic modeling and

  7. Fifty Years of Space Weather Forecasting from Boulder

    Science.gov (United States)

    Berger, T. E.

    2015-12-01

    The first official space weather forecast was issued by the Space Disturbances Laboratory in Boulder, Colorado, in 1965, ushering in an era of operational prediction that continues to this day. Today, the National Oceanic and Atmospheric Administration (NOAA) charters the Space Weather Prediction Center (SWPC) as one of the nine National Centers for Environmental Prediction (NCEP) to provide the nation's official watches, warnings, and alerts of space weather phenomena. SWPC is now integral to national and international efforts to predict space weather events, from the common and mild, to the rare and extreme, that can impact critical technological infrastructure. In 2012, the Strategic National Risk Assessment included extreme space weather events as low-to-medium probability phenomena that could, unlike any other meteorogical phenomena, have an impact on the government's ability to function. Recognizing this, the White House chartered the Office of Science and Technology Policy (OSTP) to produce the first comprehensive national strategy for the prediction, mitigation, and response to an extreme space weather event. The implementation of the National Strategy is ongoing with NOAA, its partners, and stakeholders concentrating on the goal of improving our ability to observe, model, and predict the onset and severity of space weather events. In addition, work continues with the research community to improve our understanding of the physical mechanisms - on the Sun, in the heliosphere, and in the Earth's magnetic field and upper atmosphere - of space weather as well as the effects on critical infrastructure such as electrical power transmission systems. In fifty years, people will hopefully look back at the history of operational space weather prediction and credit our efforts today with solidifying the necessary developments in observational systems, full-physics models of the entire Sun-Earth system, and tools for predicting the impacts to infrastructure to protect

  8. Boulders shifted during Supertyphoon Haiyan (7-9 Nov 2013) - Observations from Eastern Samar (Philippines)

    Science.gov (United States)

    Engel, Max; May, S. Matthias; Brill, Dominik; Cuadra, Camille; Lagmay, A. Mahar F.; Santiago, Joy; Suarez, J. Kenneth; Hoffmeister, Dirk; Brückner, Helmut

    2016-04-01

    Boulder fields record maximum magnitudes of coastal flooding during strong storms or tsunamis. Such a maximum magnitude tropical cyclone - Supertyphoon Haiyan - made landfall in the Philippines on 8 November 2013. During this typhoon, longshore transport of blocks of up to 180 t and upslope transport of boulders weighing up to 23.5 t to elevations of 10 m above mean lower low water level was documented in a combined analysis of bi-temporal satellite images and field survey at Hernani, Eastern Samar. Boulders were mapped and their volumes were derived from 3D models based on DGPS and structure-from-motion. Initiation-of-motion approaches show that boulders were shifted by flow velocities of 8.9-9.6 m/s, which significantly exceeds depth-averaged flow velocities given by a local coupled hydrodynamic and wave model (Delft3D) of the typhoon with a maximum <1.5 m/s. These results, in combination with recently published phase-resolving wave models and survivor videos from Hernani, support the hypothesis that infragravity waves induced by the typhoon, which are not resolved in phase-averaged storm surge models, were responsible for the exceptional high-velocity flooding in Eastern Samar. Our findings show that tsunamis and hydrodynamic conditions induced by storms may shift boulders of similar size and, therefore, demand a careful re-evaluation of storm-related transport where it, based on the boulder's sheer size, has previously been excluded.

  9. Project ORION: Orbital Debris Removal Using Ground-Based Sensors and Lasers

    Science.gov (United States)

    Campbell, J. W.

    1996-01-01

    About 100,000 pieces of 1 to 10-cm debris in low-Earth orbit are too small to track reliably but large enough to cripple or destroy spacecraft. The ORION team studied the feasibility of removing the debris with ground-based laser impulses. Photoablation experiments were surveyed and applied to likely debris materials. Laser intensities needed for debris orbit modification call for pulses on the order of lOkJ or continuous wave lasers on the order of 1 MW. Adaptive optics are necessary to correct for atmospheric turbulence. Wavelength and pulse duration windows were found that limit beam degradation due to nonlinear atmospheric processes. Debris can be detected and located to within about 10 microrads with existing radar and passive optical technology. Fine targeting would be accomplished with laser illumination, which might also be used for detection. Bistatic detection with communications satellites may also be possible. We recommend that existing technology be used to demonstrate the concept at a loss of about $20 million. We calculate that an installation to clear altitudes up to 800 km of 1 to 10-cm debris over 2 years of operation would cost about $80 million. Clearing altitudes up to 1,500 km would take about 3 years and cost about $160 million.

  10. Removing Manually-Generated Boilerplate from Electronic Texts: Experiments with Project Gutenberg e-Books

    CERN Document Server

    Kaser, Owen

    2007-01-01

    Collaborative work on unstructured or semi-structured documents, such as in literature corpora or source code, often involves agreed upon templates containing metadata. These templates are not consistent across users and over time. Rule-based parsing of these templates is expensive to maintain and tends to fail as new documents are added. Statistical techniques based on frequent occurrences have the potential to identify automatically a large fraction of the templates, thus reducing the burden on the programmers. We investigate the case of the Project Gutenberg corpus, where most documents are in ASCII format with preambles and epilogues that are often copied and pasted or manually typed. We show that a statistical approach can solve most cases though some documents require knowledge of English. We also survey various technical solutions that make our approach applicable to large data sets.

  11. KE Basin monorail modification for the sludge removal and packaging project

    Energy Technology Data Exchange (ETDEWEB)

    Orbeta, C.B.

    1995-02-06

    The 105KE Basin currently stores over 1,100 metric tons of various N Reactor spent fuel in several canister forms, as well as several metric tons of sludge which must be removed. Modifications will consist of anchoring a permanent steel frame directly into the pit walls between existing columns and adding two travelling hoist rails, each capable of two directional motions. Each pit will have its own capability for targeting loads to any point inside the working areas of these pits. The structural frame designed for the monorail system at the Weasel and Tech-View pits was qualified as adequate for normal/operating loads, and dead plus live loads combined with seismic loads. The hoist operating live load is limited to 2,000 lb. The physical strength of the existing pit walls where the base plates are to be structurally anchored is unknown. The original structural drawings specified a minimum concrete strength of 3,000 lb/in{sup 2}. A pullout test should be performed to verify the strength of this concrete base. To reduce radiation exposure to levels as low as reasonably achievable (ALARA), installation and erection work inside the basin controlled area must be minimized; therefore, the pieces required for the modifications should be numbered in the fabrication shop, and erection should follow a procedure that corresponds to the assembly sequence indicated by the numbers. In conjunction with final erection, a mock-up activity should be conducted and base-plate locations verified to be within dimensional tolerances.

  12. Boulder accumulations related to extreme wave events on the eastern coast of Malta

    Science.gov (United States)

    Biolchi, S.; Furlani, S.; Antonioli, F.; Baldassini, N.; Causon Deguara, J.; Devoto, S.; Di Stefano, A.; Evans, J.; Gambin, T.; Gauci, R.; Mastronuzzi, G.; Monaco, C.; Scicchitano, G.

    2015-10-01

    The accumulation of large boulders related to waves generated either by tsunamis or extreme storm events has been observed in different areas of the Mediterranean Sea. Along the NE and E low-lying rocky coasts of Malta tens of large boulder deposits have been surveyed, measured and mapped. These boulders have been detached and moved from the seafloor and lowest parts of the coast by the action of sea waves. In the Sicily-Malta channel, heavy storms are common and originate from the NE and NW winds. Conversely, few severe earthquakes and tsunamis are recorded in historical documents to have hit the Maltese archipelago, originated by seismicity activity related mainly to the Malta Escarpment, the Sicily Channel Rift Zone and the Hellenic Arc. We present a multi-disciplinary study, which aims to define the characteristics of the boulder accumulations along the eastern coast of Malta, in order to assess the coastal geo-hazard implications triggered by the sheer ability of extreme waves to detach and move large rocky blocks inland. The wave heights required to transport coastal boulders were calculated using various hydrodynamic equations. Particular attention was devoted to the quantification of the input parameters required in the workings of these equations. The axis sizes of blocks were measured with 3-D digital photogrammetric techniques and their densities were obtained throughout the use of a N-type Schmidt Hammer. Moreover, AMS ages were obtained from selected marine organisms encrusted on some of the boulders in various coastal sites. The combination of the results obtained by hydrodynamic equations and the radiocarbon dating suggests that the majority of the boulders has been detached and moved by intense storm waves. Nonetheless, it is possible that some of them may have been transported by tsunami.

  13. The thermal emission from boulders on (25143) Itokawa and general implications for the YORP effect

    CERN Document Server

    Ševeček, P; Čapek, D; Ďurech, J

    2015-01-01

    Infrared radiation emitted from an asteroid surface causes a torque that can significantly affect rotational state of the asteroid. The influence of small topographic features on this phenomenon, called the YORP effect, seems to be of utmost importance. In this work, we show that a lateral heat diffusion in boulders of suitable sizes leads to an emergence of a local YORP effect which magnitude is comparable to the YORP effect due to the global shape. We solve a three-dimensional heat diffusion equation in a boulder and its surroundings by the finite element method, using the FreeFem++ code. The contribution to the total torque is inferred from the computed temperature distribution. Our general approach allows us to compute the torque induced by a realistic irregular boulder. For an idealized boulder, our result is consistent with an existing one-dimensional model. We also estimated (and extrapolated) a size distribution of boulders on (25143) Itokawa from close-up images of its surface. We realized that topog...

  14. Removal of radon by aeration: testing of various aeration techniques for small water works. For European Commission under Contract No FI4PCT960054 TENAWA project

    International Nuclear Information System (INIS)

    Capability of various aeration techniques to remove radon from water in small waterworks was studied as a part of project (Treatment Techniques for Removing Natural Radionuclides from Drinking Water), which was carried out during 1997-1999 on a cost-shared basis (contract No. F14PCT960054) with The European Commission (CEC) under the supervision of the Directorate-General XII Radiation Protection Research Unit. In TENAWA project both laboratory and field experiments were performed in order to find reliable methods and equipment for removing natural radionuclides from ground water originating either from private wells or small waterworks. Because such techniques are more often needed in private households than at waterworks, the main emphasis of the research was aimed to solve the water treatment problems related to the private water supplies, especially bedrock wells. Radon was the most important radionuclide to be removed from water at waterworks whereas the removal of other radionuclides (234,238U, 226,228Ra, 210Pb and 210Po) was oft required from radonrich bedrock waters. The currently available methods and equipment were mainly tested during the field and laboratory experiments but the project was also aimed to find new materials, absorbents and membranes applicable for radionuclide removal from various types of ground waters (e.g. soft, hard, acidic). Because iron, manganese or organic occur in waters with radionuclides, their simultaneous removal was also studied. The project was divided into 13 work packages. In this report the results of the work package 2.2 are described. Elevated levels of radon and other natural radionuclides in European ground waters have been observed mainly in wide areas of the crystalline Scandinavian bedrock, especially in the granite rock areas of Finland and Sweden but also in more limited crystalline rock areas of Central and Southern Europe, Ukraine and Scotland. The radon removal efficiencies of different aeration methods

  15. Arsenic and Uranium Removal from Drinking Water by Adsorptive Media U.S. EPA Demonstration Project at Upper Bodfish in Lake Isabella, CA -Final Performance Evaluation Report

    Science.gov (United States)

    This report documents the activities performed during and the results obtained from the performance evaluation of an arsenic (As) and uranium (U) removal technology demonstrated at Upper Bodfish in Lake Isabella, CA. The objectives of the project are to evaluate: (1) the effecti...

  16. Prediction of blast boulders in open pit mines via multiple regression and artificial neural networks

    Institute of Scientific and Technical Information of China (English)

    Ghiasi Majid; Askarnejad Nematollah; Dindarloo Saeid R.; Shamsoddini Hamed

    2016-01-01

    The most important objective of blasting in open pit mines is rock fragmentation. Prediction of produced boulders (oversized crushed rocks) is a key parameter in designing blast patterns. In this study, the amount of boulder produced in blasting operations of Golegohar iron ore open pit mine, Iran was pre-dicted via multiple regression method and artificial neural networks. Results of 33 blasts in the mine were collected for modeling. Input variables were: joints spacing, density and uniaxial compressive strength of the intact rock, burden, spacing, stemming, bench height to burden ratio, and specific charge. The dependent variable was ratio of boulder volume to pattern volume. Both techniques were successful in predicting the ratio. In this study, the multiple regression method was superior with coefficient of determination and root mean squared error values of 0.89 and 0.19, respectively.

  17. Boulder accumulations related to extreme wave events on the eastern coast of Malta

    Science.gov (United States)

    Biolchi, Sara; Furlani, Stefano; Antonioli, Fabrizio; Baldassini, Niccoló; Causon Deguara, Joanna; Devoto, Stefano; Di Stefano, Agata; Evans, Julian; Gambin, Timothy; Gauci, Ritienne; Mastronuzzi, Giuseppe; Monaco, Carmelo; Scicchitano, Giovanni

    2016-03-01

    The accumulation of large boulders related to waves generated by either tsunamis or extreme storm events have been observed in different areas of the Mediterranean Sea. Along the eastern low-lying rocky coasts of Malta, five sites with large boulder deposits have been investigated, measured and mapped. These boulders have been detached and moved from the nearshore and the lowest parts of the coast by sea wave action. In the Sicily-Malta channel, heavy storms are common and originate from the NE and NW winds. Conversely, few tsunamis have been recorded in historical documents to have reached the Maltese archipelago. We present a multi-disciplinary study, which aims to define the characteristics of these boulder accumulations, in order to assess the coastal geo-hazard implications triggered by the sheer ability of extreme waves to detach and move large rocky blocks inland. The wave heights required to transport 77 coastal boulders were calculated using various hydrodynamic equations. Particular attention was given to the quantification of the input parameters required in the workings of these equations, such as size, density and distance from the coast. In addition, accelerator mass spectrometry (AMS) 14C ages were determined from selected samples of marine organisms encrusted on some of the coastal boulders. The combination of the results obtained both by the hydrodynamic equations, which provided values comparable with those observed and measured during the storms, and radiocarbon dating suggests that the majority of the boulders have been detached and moved by intense storm waves. These boulders testify to the existence of a real hazard for the coasts of Malta, i.e. that of very high storm waves, which, during exceptional storms, are able to detach large blocks of volumes exceeding 10 m3 from the coastal edge and the nearshore bottom, and also to transport them inland. Nevertheless, the occurrence of one or more tsunami events cannot be ruled out, since

  18. Evaluation of Boulder, CO,SmartRegs Ordinance and Better Buildings Program

    Energy Technology Data Exchange (ETDEWEB)

    Arena, L. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Vijayakumar, G. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2012-04-01

    Under the SmartRegs ordinance in the city of Boulder, Colorado, all rental properties in the city must achieve an energy efficiency level comparable to a HERS Index of approximately 120 points or lower by the year 2019. The City of Boulder received a $12 million grant from the DOE’s Better Buildings initiative to create and incentivize their EnergySmart Program. In this report, the Consortium for Advanced Residential Buildings (CARB) describes its work with the program, including energy audits of rental properties, developing training programs for insulators and inspectors, and conducting interviews with property owners.

  19. Evaluation of Boulder, CO, SmartRegs Ordinance and Better Buildings Program

    Energy Technology Data Exchange (ETDEWEB)

    Arena, L.; Vijayakumar, G.

    2012-04-01

    Under the SmartRegs ordinance in the city of Boulder, Colorado, all rental properties in the city must achieve an energy efficiency level comparable to a HERS Index of approximately 120 points or lower by the year 2019. The City of Boulder received a $12 million grant from the DOE's Better Buildings initiative to create and incentivize their EnergySmart Program. In this report, the Consortium for Advanced Residential Buildings (CARB) describes its work with the program, including energy audits of rental properties, developing training programs for insulators and inspectors, and conducting interviews with property owners.

  20. Discrete Element Method Simulation of a Boulder Extraction From an Asteroid

    Science.gov (United States)

    Kulchitsky, Anton K.; Johnson, Jerome B.; Reeves, David M.; Wilkinson, Allen

    2014-01-01

    The force required to pull 7t and 40t polyhedral boulders from the surface of an asteroid is simulated using the discrete element method considering the effects of microgravity, regolith cohesion and boulder acceleration. The connection between particle surface energy and regolith cohesion is estimated by simulating a cohesion sample tearing test. An optimal constant acceleration is found where the peak net force from inertia and cohesion is a minimum. Peak pulling forces can be further reduced by using linear and quadratic acceleration functions with up to a 40% reduction in force for quadratic acceleration.

  1. Paleo-tsunami and storm records inferred from coastal boulders along the Ryukyu Islands, Japan

    Science.gov (United States)

    Goto, K.; Miyagi, K.; Imamura, F.

    2012-12-01

    After the 11 March 2011 Tohoku-oki earthquake and tsunami (Mw=9.0) at off the coast of Tohoku district of Japan, re-evaluation of the occurrence of large earthquake and tsunami along the subduction zone is one of the major issues in Japan. Along the Ryukyu trench, there are no known thrust type earthquakes of magnitude greater than 8.0 in the last 300 years [Ando et al., 2009, 2012], although there is one possible exception: the AD1771 event at the southern Ryukyu Islands which is characterized by the ~30 m run-up heights. Hence, the occurrence of tsunamigenic large earthquake along the Ryukyu trench in the past and future is controversial. The lack of thousands of years geological record of past earthquake and tsunami such as the sandy tsunami deposits along the Ryukyu trench has made the discussion more difficult, because there are very few suitable places to study such deposits. On the other hand, numerous coastal boulders are reported on the fringing reefs of each island [e.g. Goto et al., 2010]. They are mostly composed of the coralline and reef rocks and are regarded as useful markers of the past large tsunamis and storm events. In fact, some of them are fossil Porites sp. and hence 14C dating is possible for determining the depositional age [e.g. Araoka et al., 2010]. Moreover, boulders of tsunami and storm wave origins at Ryukyu Islands can be differentiated because difference of the wave lengths of tsunami and storm wave are affected the clast size and spatial distributions of boulders on the wide fringing reef (~1500 m) [e.g. Goto et al., 2010]. Therefore, presence or absence of tsunami boulders at each island may provide useful information of occurrence of past large tsunamis and the causative earthquakes along the Ryukyu Trench. In this study, we show the clast size and spatial distributions of more than 2,500 boulders at 11 islands along the Ryukyu trench. Based on the geological study and hydrodynamic analyses, boulders on the reefs at the Sakishima

  2. 78 FR 20168 - Notice of Intent To Rule on Request To Release Airport Property at the Boulder Municipal Airport...

    Science.gov (United States)

    2013-04-03

    ... Federal Aviation Administration Notice of Intent To Rule on Request To Release Airport Property at the Boulder Municipal Airport, Boulder, CO AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of request to release airport property. SUMMARY: The FAA proposes to rule and invite public...

  3. 75 FR 42771 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2010-07-22

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY... of human remains and associated funerary objects in the control of the University of Colorado Museum.... 3003(d)(3). The determinations in this notice are the sole responsibility of the museum,...

  4. 75 FR 52015 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2010-08-24

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY... of human remains and associated funerary objects in the control of the University of Colorado Museum... determinations in this notice are the sole responsibility of the museum, institution, or Federal agency that...

  5. 76 FR 62833 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2011-10-11

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The University of Colorado Museum has completed... contact the University of Colorado Museum. Disposition of the human remains and associated funerary...

  6. 75 FR 57290 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2010-09-20

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY... of human remains and associated funerary objects in the control of the University of Colorado Museum..., 25 U.S.C. 3003(d)(3). The determinations in this notice are the sole responsibility of the...

  7. 75 FR 26988 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2010-05-13

    ..., as described in the Federal Register (71 FR 53470-53473, September 11, 2006). Also during that time... excavated from private land at the edge of Yellow Jacket Canyon, as described in the Federal Register (72 FR... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO...

  8. 75 FR 52019 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2010-08-24

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY... of human remains and associated funerary objects in the control of the University of Colorado Museum... determinations in this notice are the sole responsibility of the museum, institution, or Federal agency that...

  9. 76 FR 14063 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2011-03-15

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The University of Colorado Museum has completed... Museum. Disposition of the human remains and associated funerary objects to the Indian tribe stated...

  10. 76 FR 43715 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2011-07-21

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The University of Colorado Museum has completed... University of Colorado Museum. ] Repatriation of the human remains and associated funerary objects to...

  11. 76 FR 43713 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2011-07-21

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The University of Colorado Museum has completed... contact the University of Colorado Museum. Disposition of the human remains and associated funerary...

  12. 76 FR 62839 - Notice of Inventory Completion: University of Colorado Museum, Boulder, CO

    Science.gov (United States)

    2011-10-11

    ... National Park Service Notice of Inventory Completion: University of Colorado Museum, Boulder, CO AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The University of Colorado Museum has completed... contact the University of Colorado Museum. Disposition of the human remains to the Indian tribes...

  13. A story about estimation of a random field of boulders from incomplete seismic measurements

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    2005-01-01

    deposits along the tunnel line. By use of this important distribution information and of the observed homogeneity of the seismic point source field together with the physical properties of diffraction it became possible to make the wanted prediction. During the excavation the found boulders were counted...

  14. 75 FR 47488 - FM Table of Allotments, Boulder Town, Levan, Mount Pleasant, and Richfield, UT

    Science.gov (United States)

    2010-08-06

    ... proposed transmitter site was unavailable due to its location in a national forest. See 71 FR 29886 (May 24..., Report and Order, 71 FR 76208 (December 20, 2006). The CDBS will reflect Channel 229C at Mount Pleasant... COMMISSION 47 CFR Part 73 FM Table of Allotments, Boulder Town, Levan, Mount Pleasant, and Richfield,...

  15. Size-frequency distribution of boulders ≥7 m on comet 67P/Churyumov-Gerasimenko

    Science.gov (United States)

    Pajola, Maurizio; Vincent, Jean-Baptiste; Güttler, Carsten; Lee, Jui-Chi; Bertini, Ivano; Massironi, Matteo; Simioni, Emanuele; Marzari, Francesco; Giacomini, Lorenza; Lucchetti, Alice; Barbieri, Cesare; Cremonese, Gabriele; Naletto, Giampiero; Pommerol, Antoine; El-Maarry, Mohamed R.; Besse, Sébastien; Küppers, Michael; La Forgia, Fiorangela; Lazzarin, Monica; Thomas, Nicholas; Auger, Anne-Thérèse; Sierks, Holger; Lamy, Philippe; Rodrigo, Rafael; Koschny, Detlef; Rickman, Hans; Keller, Horst U.; Agarwal, Jessica; A'Hearn, Michael F.; Barucci, Maria A.; Bertaux, Jean-Loup; Da Deppo, Vania; Davidsson, Björn; De Cecco, Mariolino; Debei, Stefano; Ferri, Francesca; Fornasier, Sonia; Fulle, Marco; Groussin, Olivier; Gutierrez, Pedro J.; Hviid, Stubbe F.; Ip, Wing-Huen; Jorda, Laurent; Knollenberg, Jörg; Kramm, J.-Rainer; Kürt, Ekkehard; Lara, Luisa M.; Lin, Zhong-Yi; Lopez Moreno, Jose J.; Magrin, Sara; Marchi, Simone; Michalik, Harald; Moissl, Richard; Mottola, Stefano; Oklay, Nilda; Preusker, Frank; Scholten, Frank; Tubiana, Cecilia

    2015-11-01

    Aims: We derive for the first time the size-frequency distribution of boulders on a comet, 67P/Churyumov-Gerasimenko (67P), computed from the images taken by the Rosetta/OSIRIS imaging system. We highlight the possible physical processes that lead to these boulder size distributions. Methods: We used images acquired by the OSIRIS Narrow Angle Camera, NAC, on 5 and 6 August 2014. The scale of these images (2.44-2.03 m/px) is such that boulders ≥7 m can be identified and manually extracted from the datasets with the software ArcGIS. We derived both global and localized size-frequency distributions. The three-pixel sampling detection, coupled with the favorable shadowing of the surface (observation phase angle ranging from 48° to 53°), enables unequivocally detecting boulders scattered all over the illuminated side of 67P. Results: We identify 3546 boulders larger than 7 m on the imaged surface (36.4 km2), with a global number density of nearly 100/km2 and a cumulative size-frequency distribution represented by a power-law with index of -3.6 +0.2/-0.3. The two lobes of 67P appear to have slightly different distributions, with an index of -3.5 +0.2/-0.3 for the main lobe (body) and -4.0 +0.3/-0.2 for the small lobe (head). The steeper distribution of the small lobe might be due to a more pervasive fracturing. The difference of the distribution for the connecting region (neck) is much more significant, with an index value of -2.2 +0.2/-0.2. We propose that the boulder field located in the neck area is the result of blocks falling from the contiguous Hathor cliff. The lower slope of the size-frequency distribution we see today in the neck area might be due to the concurrent processes acting on the smallest boulders, such as i) disintegration or fragmentation and vanishing through sublimation; ii) uplifting by gas drag and consequent redistribution; and iii) burial beneath a debris blanket. We also derived the cumulative size-frequency distribution per km2 of

  16. Aswan site on comet 67P/Churyumov-Gerasimenko: Morphology, boulder evolution, and spectrophotometry

    Science.gov (United States)

    Pajola, Maurizio; Oklay, Nilda; La Forgia, Fiorangela; Giacomini, Lorenza; Massironi, Matteo; Bertini, Ivano; El-Maarry, M. R.; Marzari, Francesco; Preusker, Frank; Scholten, Frank; Höfner, Sebastian; Lee, Jui-Chi; Vincent, Jean-Baptiste; Groussin, Olivier; Naletto, Giampiero; Lazzarin, Monica; Barbieri, Cesare; Sierks, Holger; Lamy, Philippe; Rodrigo, Rafael; Koschny, Detlef; Rickman, Hans; Keller, Horst U.; Agarwal, Jessica; A'Hearn, Michael F.; Barucci, Maria A.; Bertaux, Jean-Loup; Cremonese, Gabriele; Da Deppo, Vania; Davidsson, Björn; De Cecco, Mariolino; Debei, Stefano; Ferri, Francesca; Fornasier, Sonia; Fulle, Marco; Güttler, Carsten; Gutierrez, Pedro J.; Hviid, Stubbe F.; Ip, Wing-Huen; Jorda, Laurent; Knollenberg, Jörg; Kramm, J.-Rainer; Küppers, Michael; Kürt, Ekkehard; Lara, Luisa M.; Lin, Zhong-Yi; Lopez Moreno, Jose J.; Magrin, Sara; Michalik, Harald; Mottola, Stefano; Thomas, Nicholas; Tubiana, Cecilia

    2016-07-01

    Aims: We provide a detailed morphological analysis of the Aswan site on comet 67P/Churyumov-Gerasimenko (67P). We derive the size-frequency distribution of boulders ≥2 m and correlate this distribution with the gravitational slopes for the first time on a comet. We perform the spectral analysis of this region to understand if possible surface variegation is related to thedifferent surface textures observable on the different units. Methods: We used two OSIRIS Narrow Angle Camera (NAC) image data sets acquired on September 19 and 22, 2014, with a scale of 0.5 m/px. Gravitational slopes derived from the 3D shape model of 67P were used to identify and interpret the different units of the site. By means of the high-resolution NAC data sets, boulders ≥2.0 m can be unambiguously identified and extracted using the software ArcGIS. Coregistered and photometrically corrected color cubes were used to perform the spectral analyses, and we retrieved the spectral properties of the Aswan units. Results: The high-resolution morphological map of the Aswan site (0.68 km2) shows that this site is characterized by four different units: fine-particle deposits located on layered terrains, gravitational accumulation deposits, taluses, and the outcropping layered terrain. Multiple lineaments are identified on the Aswan cliff, such as fractures, exposed layered outcrops, niches, and terraces. Close to the terrace margin, several arched features observed in plan view suggest that the margin progressively retreats as a result of erosion. The size-frequency of boulders ≥2 m in the entire study area has a power-law index of -3.9 +0.2/-0.3 (1499 boulders ≥2 m/km2), suggesting that the Aswan site is mainly dominated by gravitational events triggered by sublimation and/or thermal insolation weathering causing regressive erosion. The boulder size-frequency distribution versus gravitational slopes indicates that when higher gravitational slope terrains are considered, only boulders ≤10 m

  17. PROJECT-SPECIFIC TYPE A VERIFICATION FOR THE HIGH FLUX BEAM REACTOR UNDERGROUND UTILITIES REMOVAL PHASE 2 D/F WASTE LINE REMOVAL, BROOKHAVEN NATIONAL LABORATORY UPTON, NEW YORK

    International Nuclear Information System (INIS)

    Oak Ridge Institute for Science and Education (ORISE) has reviewed the project documentation and data for the High Flux Beam Reactor (HFBR) Underground Utilities removal Phase 2; the D/F Waste Line removal at Brookhaven National Laboratory (BNL) in Upton, New York. The Brookhaven Survey Group (BSG) has completed removal and performed the final status survey (FSS) of the D/F Waste Line that provided the conduit for pumping waste from Building 750 to Building 801. Sample results have been submitted as required to demonstrate that the cleanup goals of 15 mrem/yr above background to a resident in 50 years have been met. Four rounds of sampling, from pre-excavation to final status survey (FSS), were performed as specified in the Field Sampling Plan (FSP) (BNL 2010a). It is the policy of the US Departmental of Energy (DOE) to perform independent verifications of decontamination and decomissioning activities conducted at DOE facilities. ORISE has been designated as the organization responsible for this task at the HFBR. ORISE together with DOE determined that a Type A verification of the D/F Waste Line was appropriate based on its method of construction and upon the minimal potential for residual radioactivity in the area. The removal of underground utilities is being performed in three stages in the process to decommission the HFBR facility and support structures. Phase 2 of this project included the grouting and removal of 1100 feet of 2-inch pipe and 640 feet of 4-inch pipe that served as the D/F Waste Line. Based on the pre-excavation sample results of the soil overburden, the potential for contamination of the soil surrounding the pipe is minimal (BNL 2010a). ORISE reviewed the BNL FSP and identified comments for consideration (ORISE 2010). BNL prepared a revised FSP that addressed each ORISE comment adequately (BNL 2010a). ORISE referred to the revised Phase 2 D/F Waste Line removal FSP FSS data to conduct the Type A verification and determine whether the intent odf

  18. What do Meteorite Falls Tell Us about the Strength of Asteroid Boulders

    Science.gov (United States)

    Britt, Daniel; Demasi, Michael; Kring, David

    2016-10-01

    One possible source of data on the strength of a boulder on an asteroid's surface is the meteorite collection and the observations of meteorite falls. Since highly fractured boulders should breakup in the atmosphere and arrive as meteorite showers, the relative ratio of boulders to showers can provide insight into boulder strength. Since about 85-95% of the mass of a meteoroid is lost during atmospheric entry, we have chosen to investigate only those falls with a final recovered mass of at least 10 kg. This corresponds to a minimum pre-atmospheric mass of 100-200 kg and roughly 25 centimeter minimum diameter. Using the Catalogue of Meteorites and the Meteoritical Bulletins we compiled a list of observed meteorite falls with a total recovered mass greater than or equal to 10 kg. We found a total of 269 meteorites that met these criteria, of which 263 entries reported or estimated the number of fragments associated with their falls. The overall percentage of observed showers was found to be around 34%. The ratio of "boulders" to showers was determined to be around 1.94:1. Comparing the percentage of showers within the meteorite types shows a trend in strength with irons (showers only 4.3%) very rarely exhibit reported showers, stony-irons (25%), ordinary chondrites (28.5%), achondrites (35.7%), and carbonaceous chondrites (70%) are dominantly showers.The meteorite fall data primarily sample the "boulder" population of meteoroids roughly 0.25 meters to a few meters in their pre-atmospheric diameter because of the 85-95% atmospheric loss. The relative rarity of showers seems to indicate that most meteoroids that survive to produce meteorites in this size range are fairly strong and coherent. Not surprisingly, irons and stony-irons are the strongest class which is consistent with the overwhelmingly high production of Earth's smallest impact craters by iron meteorites. Carbonaceous chondrites are by far the weakest and most fracture-prone meteorite class with 70% of the

  19. Spatial heterogeneity of temperature across alpine boulder fields in New South Wales, Australia: multilevel modelling of drivers of microhabitat climate.

    Science.gov (United States)

    Shi, Haijing; Paull, David; Rayburg, Scott

    2016-07-01

    Understanding the spatial heterogeneity of temperatures across a region is significant for identification and protection of potential microhabitats for species conservation. However, this task is proving difficult because multiple factors drive the temperatures of microhabitats and their effect differs at different scales. In the Australian alpine region, boulder field habitats have been identified as important refugia for a range of small mammals. Vegetation cover and elevation have been found to drive thermal buffering at the level of single sampling sites within boulder fields, whereas the aspect and inclination of slopes have been found to affect thermal buffering at the level of clusters of boulder fields. But how the rock structure (number of rock layers, rock size and cavity of boulders) influences microclimate of boulder fields remains an open question. We used a multilevel modelling approach to detect the factors driving microhabitat temperatures in different seasons at different spatial scales in an Australian alpine region. We found that significant temperature differences existed within and between clusters of boulder fields in different seasons. Besides elevation and vegetation cover, the number of rock layers and rock cavity size also exerts important influences on extreme temperatures at the site (i.e. single boulder field) scale. Topographical variables such as slope gradient and elevation influenced minimum temperatures at the boulder field cluster scale. Variations in boulder field temperatures were significant at fine scales, with variations in minimum temperatures exceeding those of maximum temperatures. We suggest that variations in slope gradient and elevation, interacting with vegetation cover, the number of rock layers and rock cavity size can lead to fine-grained thermal variability, which potentially provides refugia for species at microsites, even when regional climatic conditions become less suitable for their survival. PMID:26511483

  20. Spatial heterogeneity of temperature across alpine boulder fields in New South Wales, Australia: multilevel modelling of drivers of microhabitat climate

    Science.gov (United States)

    Shi, Haijing; Paull, David; Rayburg, Scott

    2016-07-01

    Understanding the spatial heterogeneity of temperatures across a region is significant for identification and protection of potential microhabitats for species conservation. However, this task is proving difficult because multiple factors drive the temperatures of microhabitats and their effect differs at different scales. In the Australian alpine region, boulder field habitats have been identified as important refugia for a range of small mammals. Vegetation cover and elevation have been found to drive thermal buffering at the level of single sampling sites within boulder fields, whereas the aspect and inclination of slopes have been found to affect thermal buffering at the level of clusters of boulder fields. But how the rock structure (number of rock layers, rock size and cavity of boulders) influences microclimate of boulder fields remains an open question. We used a multilevel modelling approach to detect the factors driving microhabitat temperatures in different seasons at different spatial scales in an Australian alpine region. We found that significant temperature differences existed within and between clusters of boulder fields in different seasons. Besides elevation and vegetation cover, the number of rock layers and rock cavity size also exerts important influences on extreme temperatures at the site (i.e. single boulder field) scale. Topographical variables such as slope gradient and elevation influenced minimum temperatures at the boulder field cluster scale. Variations in boulder field temperatures were significant at fine scales, with variations in minimum temperatures exceeding those of maximum temperatures. We suggest that variations in slope gradient and elevation, interacting with vegetation cover, the number of rock layers and rock cavity size can lead to fine-grained thermal variability, which potentially provides refugia for species at microsites, even when regional climatic conditions become less suitable for their survival.

  1. Podnikatelská plán pro založení boulder centra

    OpenAIRE

    Herman, Jan

    2010-01-01

    Diplomová práce se zabývá sestavením podnikatelského záměru pro založení Boulder Centra v Brně. Jde o horolezeckou stěnu spojenou s možností posezení. Na základě ekonomických analýz je sestaven podnikatelský plán, který určuje šanci a podmínky realizace daného projektu. The Master Thesis deals with a business plan for setting up a Boulder Centre in Brno. The centre will comprise of a gym for rock climbing and a bar. The bussines plan is based on economic analyses and determines the conditi...

  2. The quantitative estimation of the vulnerability of brick and concrete wall impacted by an experimental boulder

    OpenAIRE

    Zhang, J.; Guo, Z. X.; Wang, D; Qian, H.

    2016-01-01

    There is little historic data about the vulnerability of damaged elements due to debris flow events in China. Therefore, it is difficult to quantitatively estimate the vulnerable elements suffered by debris flows. This paper is devoted to the research of the vulnerability of brick and concrete walls impacted by debris flows. An experimental boulder (an iron sphere) was applied to be the substitute of debris flow since it can produce similar shape impulse load on elements as ...

  3. Preliminary engineering report waste area grouping 5, Old Hydrofracture Facility Tanks content removal project, Oak Ridge National Laboratory, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    The Superfund Amendments and Reauthorization Act of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) requires a Federal Facilities Agreement (FFA) for federal facilities placed on the National Priorities List. The Oak Ridge Reservation was placed on that list on December 21, 1989, and the agreement was signed in November 1991 by the U.S. Department of Energy (DOE) Oak Ridge Operations Office, the U.S. Environmental Protection Agency (EPA) Region IV, and the Tennessee Department of Environment and Conservation (TDEC). The effective date of the FFA is January 1, 1992. One objective of the FFA is to ensure that liquid low-level waste (LLLW) tanks that are removed from service are evaluated and remediated through the CERCLA process. Five inactive LLLW tanks, designated T-1, T-2, T-3, T-4, and T-9, located at the Old Hydrofracture (OHF) Facility in the Melton Valley area of Oak Ridge National Laboratory (ORNL) have been evaluated and are now entering the remediation phase. As a precursor to final remediation, this project will remove the current liquid and sludge contents of each of the five tanks (System Requirements Document, Appendix A). It was concluded in the Engineering Evaluation/Cost Analysis [EE/CA] for the Old Hydrofracture Facility Tanks (DOE 1996) that sluicing and pumping the contaminated liquid and sludge from the five OHF tanks was the preferred removal action. Evaluation indicated that this alternative meets the removal action objective and can be effective, implementable, and cost-effective. Sluicing and removing the tank contents was selected because this action uses (1) applicable experience, (2) the latest information about technologies and techniques for removing the wastes from the tanks, and (3) activities that are currently acceptable for storage of transuranic (TRU) mixed waste.

  4. Radioactive Air Emissions Notice of Construction (NOC) for the Solid Waste Treatment Facility (T Plant) Fuel Removal Project

    Energy Technology Data Exchange (ETDEWEB)

    JOHNSON, R.E.

    2000-11-16

    This NOC describes the activities to remove all spent nuclear fuel (SNF) assemblies from the spent fuel pool in the T Plant Complex 221-T canyon for interim storage in the Canister Storage Building (CSB). The unabated total effective dose equivalent (TEDE) estimated for the public hypothetical maximally exposed individual (MEI) is 5.7 E-6 millirem (mrem) per year for this fuel removal NOC. The abated TEDE conservatively is estimated to account for 2.9 E-9 mrem per year to the MEI.

  5. First evidence of accumulation of mega boulders on the Mediterranean rocky coast of Provence (southern France

    Directory of Open Access Journals (Sweden)

    C. Vella

    2011-03-01

    Full Text Available An accumulation of boulders was recently discovered along the rocky coast of the Gulf of Fos located in Provence, in an area exposed to a south-westerly wave regime. The coast around this locality forms the western extremity of the calcareous Nerthe range between Marseille and the Rhône Delta. Several mega blocks are scattered to a distance of 30 m behind the coast line. The largest block (33.5 tonnes has been transported about 39 m inland, up to about 2 m a.s.l. On the Mediterranean coast, the origin of such blocks is often attributed to tsunami-generated waves, but in the case examined here, although the origin is unclear, the differences in surface state between boulders indicates several events generated by south-westerly storms. Radiocarbon dating on several different shells collected from seven different boulders yields a wide dispersion of ages ranging from 4000 BP to the Modern Period. The differences in surface appearance, as well as the differences of fauna conservation and surface coloration, in some cases in a very fresh state, along with the dispersion of radiocarbon ages, suggest that historic storm events have affected these megablocks.

  6. First evidence of accumulation of mega boulders on the Mediterranean rocky coast of Provence (southern France)

    Science.gov (United States)

    Vella, C.; Demory, F.; Canut, V.; Dussouillez, P.; Fleury, T. J.

    2011-03-01

    An accumulation of boulders was recently discovered along the rocky coast of the Gulf of Fos located in Provence, in an area exposed to a south-westerly wave regime. The coast around this locality forms the western extremity of the calcareous Nerthe range between Marseille and the Rhône Delta. Several mega blocks are scattered to a distance of 30 m behind the coast line. The largest block (33.5 tonnes) has been transported about 39 m inland, up to about 2 m a.s.l. On the Mediterranean coast, the origin of such blocks is often attributed to tsunami-generated waves, but in the case examined here, although the origin is unclear, the differences in surface state between boulders indicates several events generated by south-westerly storms. Radiocarbon dating on several different shells collected from seven different boulders yields a wide dispersion of ages ranging from 4000 BP to the Modern Period. The differences in surface appearance, as well as the differences of fauna conservation and surface coloration, in some cases in a very fresh state, along with the dispersion of radiocarbon ages, suggest that historic storm events have affected these megablocks.

  7. Set Point Calculations for RAPID Project [Removal of Hold for HNF-5087 and HNF-5088 and HNF-5089

    International Nuclear Information System (INIS)

    The Respond and Pump in Days (RAPID) project was initiated to pump part of the contents of tank 241-SY-101 into tanks 241-SY-102. This document establishes the basis for all set points and ranges used in the RAPID project

  8. Set Point Calculations for RAPID Project [Removal of Hold for HNF-5087 and HNF-5088 and HNF-5089

    Energy Technology Data Exchange (ETDEWEB)

    HICKMAN, G.L.

    1999-09-02

    The Respond and Pump in Days (RAPID) project was initiated to pump part of the contents of tank 241-SY-101 into tanks 241-SY-102. This document establishes the basis for all set points and ranges used in the RAPID project.

  9. Extent of Abandoned Underground Coal Mines and Surface Mines in the Boulder-Weld Coal Field (friminedu)

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This file is a digital polygon representation of the areal extent of abandoned underground coal mines and surface mines in the Boulder-Weld coal field, Denver...

  10. Arsenic/Radium Removal from Drinking Water by the HMO Process, U.S. EPA Demonstration Project at Greenville, WI

    Science.gov (United States)

    In 2003, the Town of Greenville, Wisconsin was selected for the Round 2 U.S. Environmental Protection Agency (EPA) Arsenic Demonstration Program and a Kinetico Macrolite® pressure filtration system was selected for its ability to remove arsenic. Well reconstruction prior to the ...

  11. Cephalopholis argus fish census and assemblage data from the West Hawaii Roi Removal Project 2010-2012 (NODC Accession 0099263)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This project examined the results of the field manipulative experiment that has been set up to test the ecological effects of introduced roi on reef fish...

  12. Removal Action Workplan for the 105-DR and 105-F Building Interim Safe Storage Projects and Ancillary Buildings

    International Nuclear Information System (INIS)

    This document is the removal action workplan (RAW) for the 105-DR and 105-F Reactor Buildings and ancillary facilities. These buildings and facilities are located in the 100-D/DR and 100-F Areas of the Hanford Site in Benton County, Washington, which is owned and operated by the U.S. Department of Energy (DOE). The 100 Areas (including 100-D/DR and 100-F Areas) of the Hanford Site were placed on the U.S. Environmental Protection Agency's (EPA) National Priorities List under the Comprehensive Environmental Response, Compensation,and Liability Act of 1980 (CERCLA). DOE has determined that hazardous substances in the 105-DR and 105-F Reactor Buildings and four ancillary facilities present a potential threat to human health or the environment DOE has also determined that a non-time critical removal action is warranted at these facilities

  13. Cleanup and treatment (CAT) test: a land-area decontamination project utilizing a vacuum method of soil removal

    International Nuclear Information System (INIS)

    Areas 11 and 13 of the Nevada Test Site (NTS) are contaminated with varying concentrations of Pu-239, 240 and Am-241. An investigation of a vacuum method of soil removal, the Cleanup and Treatment (CAT) test, was conducted over a 3-month period in the plutonium safety shot or Plutonium Valley portion of Area 11. Soil in Plutonium Valley is of the Aridisol Order. The surface 0 to 10 cm is a gravelly loam, and is strongly alkaline (pH 8.8). A large truck-mounted vacuum unit, rather than conventional earth-moving equipment, was used as the primary soil collection unit. Effectiveness of the vacuum method of soil removal was evaluated in relation to conventional earthmoving procedures, particularly in terms of volume reduction of removed soil achieved over conventional techniques. Radiological safety considerations associated with use of the vacuum unit were evaluated in relation to their impact on a full-scale land decontamination program. Environmental and operational impacts of devegetation with retention of root crowns or root systems were investigated. It is concluded that the CAT test was successful under difficult environmental conditions

  14. Cleanup and treatment (CAT) test: a land-area decontamination project utilizing a vacuum method of soil removal

    Energy Technology Data Exchange (ETDEWEB)

    Orcutt, J.A.

    1982-08-01

    Areas 11 and 13 of the Nevada Test Site (NTS) are contaminated with varying concentrations of Pu-239, 240 and Am-241. An investigation of a vacuum method of soil removal, the Cleanup and Treatment (CAT) test, was conducted over a 3-month period in the plutonium safety shot or Plutonium Valley portion of Area 11. Soil in Plutonium Valley is of the Aridisol Order. The surface 0 to 10 cm is a gravelly loam, and is strongly alkaline (pH 8.8). A large truck-mounted vacuum unit, rather than conventional earth-moving equipment, was used as the primary soil collection unit. Effectiveness of the vacuum method of soil removal was evaluated in relation to conventional earthmoving procedures, particularly in terms of volume reduction of removed soil achieved over conventional techniques. Radiological safety considerations associated with use of the vacuum unit were evaluated in relation to their impact on a full-scale land decontamination program. Environmental and operational impacts of devegetation with retention of root crowns or root systems were investigated. It is concluded that the CAT test was successful under difficult environmental conditions.

  15. Astronaut John Young looks over a boulder at Station no. 13 during EVA

    Science.gov (United States)

    1972-01-01

    Astronaut John W. Young, commander of the Apollo 16 lunar landing mission, looks over a large boulder at Station No. 13 during the third Apollo 16 extravehicular activity (EVA-3) at the Descartes landing site. This was the site of the permanently shadowed soil sample which was taken from a hole extending under overhanging rock. Astronaut Charles M. Duke Jr., lunar module pilot, took this photograph. Concerning Young's reaching under the big rock, Duke remarked: 'You do that in west Texas and you get a rattlesnake!'

  16. ARSENIC REMOVAL FROM DRINKING WATER BY POINT-OF-USE (POU) REVERSE OSMOSIS. U.S. EPA DEMONSTRATION PROJECT AT SUNSET RANCH DEVELOPMENT IN HOMEDALE, ID. FINAL PERFORMANCE EVALUATION REPORT

    Science.gov (United States)

    This report documents the activities performed during and the results obtained from the arsenic removal technology demonstration project at the Sunset Ranch Development in Homedale, ID. The objectives of the project are to evaluate: 1) the effectiveness of a point of use (POU) re...

  17. Arsenic Removal from Drinking Water by Oxidation/Filtration and Adsorptive Media, U.S. EPA Demonstration Project at Clinton Christian School in Goshen, IN - Final Performance Evaluation Report

    Science.gov (United States)

    This report documents the activities performed for and the results obtained from the arsenic removal treatment technology demonstration project at the Clinton Christian School in Goshen, IN. The objectives of the project were to evaluate the effectiveness of AdEdge Technologies’...

  18. Persistence of 10-year old Exxon Valdez oil on Gulf of Alaska beaches: The importance of boulder-armoring

    Energy Technology Data Exchange (ETDEWEB)

    Irvine, G.V. [United States Geological Survey , Anchorage, AK (United States); Mann, D.H. [University of Alaska, Fairbanks, AK (United States). Institute of Arctic Biology; Short, J.W. [National Oceanic and Atmospheric Administration, Juneau, AK (United States). Auke Bay Fisheries Laboratory

    2006-09-15

    Oil stranded as a result of the 1989 Exxon Valdez spill has persisted for >10 years at study sites on Gulf of Alaska shores distant from the spill's origin. These sites were contaminated by 'oil mousse', which persists in these settings due to armoring of underlying sediments and their included oil beneath boulder. The boulder-armored beaches that we resampled in 1999 showed continued contamination by subsurface oil, despite their exposure to moderate to high wave energies. Significant declines in surface oil cover occurred at all study sites. In contrast, mousse has persisted under boulders in amounts similar to what was present in 1994 and probably in 1989. Especially striking is the general lack of weathering of this subsurface oil over the last decade. Oil at five of the six armored-beach sites 10 years after the spill is compositionally similar to 11-day old Exxon Valdez oil. Analysis of movements in the boulder-armor that covers the study beaches reveals that only minor shifts have occurred since 1994, suggesting that over the last five, and probably over the last 10 years, boulder-armors have remained largely unmoved at the study sites. These findings emphasize the importance of particular geomorphic parameters in determining stranded oil persistence. Surface armoring, combined with stranding of oil mousse, results in the unexpectedly lengthy persistence of only lightly to moderately weathered oil within otherwise high-energy wave environments. (author)

  19. Radiological and chemical completion report for overhead piping removal for the Weldon Spring Site Remedial Action Project, Weldon Spring, Missouri

    International Nuclear Information System (INIS)

    Demolition of overhead piping and supports at the Weldon Spring Chemical Plant was undertaken as an interim response action (IRA) within the Weldon Spring Site Remedial Action Project. IRAs are designed to ensure the health and safety of on-site personnel and minimize or preclude off-site releases of contamination. Prior to dismantlement a radiological survey and release plan was developed. Any radiologically contaminated material which exceeded release criteria was retained on site, along with all asbestos-containing insulation. Uncontaminated piping and supports were released from the site for salvage. This report summarizes the methods used to survey and release piping and supports and the amount of material released. 5 refs., 2 figs., 4 tabs

  20. Paleoenvironmental reconstruction of microbial mud mound derived boulders from gravity-flow polymictic megabreccias (Visean, SW Spain)

    Science.gov (United States)

    Rodríguez-Martínez, M.; Moreno-González, I.; Mas, R.; Reitner, J.

    2012-07-01

    The Upper Visean outcrops from the Guadiato Valley (Córdoba, SW Spain) provide a well-preserved record of the mud mound factory, which was developed in a mainly siliciclastic synorogenic foreland basin during the oblique sinistral collision of two terranes (Ossa Morena and Central Iberian blocks). The first onset of mud mound development has been recorded as microbial mud mound-derived boulders in polymictic megabreccias as result of strong tectonic activity. The Upper Visean record from the Mississippian central band at Guadiato Valley starts with lower heterolithic units (up to 180 m thick) and shows two major tectonically-controlled cycles: a fining upwards interval (FU) followed by a coarsening upwards interval (CU). These cycles are linked to two active margins with gravelly fan delta development and different source areas. Mud mound-derived boulders occur in the CU interval and are formed by peloidal primary and secondary (reworked) automicrites and allomicrites, showing a diverse faunal and floral assemblage, although never as the main skeletal framebuilders. However, the observed coeval richness in sponges (lyssacinose hexactinellids and non-lithistid demosponges) and the diverse calcareous algae assemblage in mud mound derived boulders are not common in other Visean buildups. The growth cavities display changes in the geopetal relationships between fillings and the secondary cavities containing sand to gravel fillings reflecting a complex pre-boulder and mud mound derived boulder history. Detailed mapping, sampling, stratigraphic and microfacial analyses have allowed the reconstruction of the mud mounds sedimentary environment prior to the collapse, transport and emplacement as boulders with polymictic gravels.

  1. Assessment of the Effect of Blast Hole Diameter on the Number of Oversize Boulders Using ANN Model

    Science.gov (United States)

    Dhekne, Prakash; Pradhan, Manoj; Jade, Ravi Krishnarao

    2016-04-01

    Now-a-days, blasts are planned using large diameter blast holes. The loading density (kg/m) and subsequently the energy available for the breakage of the rockmass increase with the diameter. The in-hole velocity of detonation (VoD) of non-ideal explosive also boosts up with the increase in diameter till the optimum diameter is reached. The increase in the energy content and in-hole VoD cause a sizable effect on the rock fragmentation. The effect can be assessed by counting the number of oversize boulders. This paper explains as to how the technique of artificial neural network modeling was used to predict the number of oversize boulders resulting from ANFO and SME blasts with blast holes of different diameters. The results from ANFO blasts indicated that there was no significant variation in the number of oversize boulders with the diameter whereas a perceptible variation was noticed in case of SME blasts with the change in the diameter. The change in the number of oversize boulders in ANFO blasts was negligible because mean energy factor remained almost same even when the diameter of the blast holes was altered. The decrease in the number of oversize boulders in SME blasts was on account of increase in mean energy factor when the blast hole diameter was increased. The increase in the in-hole VoD due to increase in the diameter of the hole was not found to have an effect on the generation of oversize boulders as this increase was not substantial both in SME and ANFO blasts.

  2. Field grouting summary report on the WAG seeps 4 and 6 removal action project, Oak Ridge National Laboratory, Oak Ridge, Tennessee. Volume 1: Text

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-01

    During the summer of 1996, a unique multi-phase, multi-stage, low-pressure permeation grouting pilot program was performed inside portions of four unlined waste disposal trenches at Waste Area Grouping (WAG) 4 at Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee. The project was deemed a non-time-critical removal action under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA); however, due to a history of heavy precipitation in the fall, the schedule was fast-tracked to meet an October 31, 1996 grouting completion date. The technical objective of the removal action was to reduce the off-site transport of Strontium 90 ({sup 90}Sr) by grouting portions of four waste disposal trenches believed to be responsible for over 70% of the {sup 90}Sr leaving the site. A goal of the grouting operation was to reduce the average in situ hydraulic conductivity of the grouted waste materials to a value equal to or less than 1 x 10{sup {minus}6} cm/sec. This target hydraulic conductivity value was established to be at least two orders of magnitude lower than that of the surrounding natural ground.

  3. Field grouting summary report on the WAG 4 seeps 4 and 6 removal action project, Oak Ridge National Laboratory, Oak Ridge, Tennessee. Volume 3. Appendixes E and F

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-01

    During the summer of 1996, a unique multi-phase, multi-stage, low-pressure permeation grouting pilot program was performed inside portions of four unlined waste disposal trenches at Waste Area Grouping (WAG) 4 at Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee. The project was deemed a non-time-critical removal action under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA); however, due to a history of heavy precipitation in the fall, the schedule was fast-tracked to meet an October 31, 1996 grouting completion date. The technical objective of the removal action was to reduce the off-site transport of j Strontium 90 ({sup 90}Sr) by grouting portions of four waste disposal trenches believed to be responsible for over 70 percent of the {sup 90}Sr leaving the site. A goal of the grouting operation was to reduce the average in situ hydraulic conductivity of the grouted waste materials to a value equal to or less than 1 x 10{sup -6} cm/sec. This target hydraulic conductivity value was established to be at least two orders of magnitude lower than that of the surrounding natural ground.

  4. Field grouting summary report on the WAG seeps 4 and 6 removal action project, Oak Ridge National Laboratory, Oak Ridge, Tennessee. Volume 1: Text

    International Nuclear Information System (INIS)

    During the summer of 1996, a unique multi-phase, multi-stage, low-pressure permeation grouting pilot program was performed inside portions of four unlined waste disposal trenches at Waste Area Grouping (WAG) 4 at Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee. The project was deemed a non-time-critical removal action under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA); however, due to a history of heavy precipitation in the fall, the schedule was fast-tracked to meet an October 31, 1996 grouting completion date. The technical objective of the removal action was to reduce the off-site transport of Strontium 90 (90Sr) by grouting portions of four waste disposal trenches believed to be responsible for over 70% of the 90Sr leaving the site. A goal of the grouting operation was to reduce the average in situ hydraulic conductivity of the grouted waste materials to a value equal to or less than 1 x 10-6 cm/sec. This target hydraulic conductivity value was established to be at least two orders of magnitude lower than that of the surrounding natural ground

  5. Field grouting summary report on the WAG 4 seeps 4 and 6 removal action project, Oak Ridge National Laboratory, Oak Ridge, Tennessee. Volume 3. Appendixes E and F

    International Nuclear Information System (INIS)

    During the summer of 1996, a unique multi-phase, multi-stage, low-pressure permeation grouting pilot program was performed inside portions of four unlined waste disposal trenches at Waste Area Grouping (WAG) 4 at Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee. The project was deemed a non-time-critical removal action under the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA); however, due to a history of heavy precipitation in the fall, the schedule was fast-tracked to meet an October 31, 1996 grouting completion date. The technical objective of the removal action was to reduce the off-site transport of j Strontium 90 (90Sr) by grouting portions of four waste disposal trenches believed to be responsible for over 70 percent of the 90Sr leaving the site. A goal of the grouting operation was to reduce the average in situ hydraulic conductivity of the grouted waste materials to a value equal to or less than 1 x 10-6 cm/sec. This target hydraulic conductivity value was established to be at least two orders of magnitude lower than that of the surrounding natural ground

  6. Survival times of meter-sized rock boulders on the surface of airless bodies

    Science.gov (United States)

    Basilevsky, A. T.; Head, J. W.; Horz, F.; Ramsley, K.

    2015-11-01

    Rock boulders are typical features of the surfaces of many airless bodies, so the possibility of estimating their potential survival times may provide insights into the rates of surface-modification processes. As an opening point of this study we employ estimates of the survival times of meter-sized boulders on the surface of the Moon based on analysis of the spatial density of boulders on the rims of small lunar craters of known absolute age (Basilevsky et al., 2013), and apply them, with necessary corrections, to boulders on other bodies. In this approach the major factor of rock destruction is considered to be impacts of meteorites. However another factor of the rock destruction, thermal fatigue due to day-night cycling, does exist and it was claimed by Delbo et al. (2014) as being more important than meteorite impacts. They concluded this on the basis of known presence of fine material on the surface of small asteroids, claiming that due to extremely low gravity on those bodies, the products of meteorite bombardment should leave these bodies, and thus their presence indicates that the process of thermal fatigue should be much more effective there. Delbo et al. (2014) made laboratory experiments on heating-cooling centimeter-sized samples of chondrites and, applying some assumptions and theoretical modeling concluded that, for example, at 1 AU distance from the Sun, the lifetime of 10 cm rock fragments on asteroids with period of rotation from 2.2 to 6 h should be only ~103 to 104 years (that is ~3.5×106 to 1.5×107 thermal cycles) and the larger the rock, the faster it should be destroyed. In response to those conclusions we assessed the results of earlier laboratory experiments, which show that only a part of comminuted material produced by high-velocity impacts into solid rocks is ejected from the crater while another part is not ejected but stays exposed on the target surface and is present in its subsurface. This means that the presence of

  7. PROJECT-SPECIFIC TYPE A VERIFICATION FOR THE HIGH FLUX BEAM REACTOR UNDERGROUND UTILITIES REMOVAL PHASE 3 TRENCH 5, BROOKHAVEN NATIONAL LABORATORY UPTON, NEW YORK

    International Nuclear Information System (INIS)

    The Oak Ridge Institute for Science and Education (ORISE) has reviewed the project documentation and data for the High Flux Beam Reactor (HFBR) Underground Utilities removal Phase 3; Trench 5 at Brookhaven National Laboratory (BNL) in Upton, New York. The Brookhaven Survey Group (BSG) has completed removal and performed Final Status Survey (FSS) of the concrete duct from Trench 5 from Building 801 to the Stack. Sample results have been submitted as required to demonstrate that the cleanup goal of (le)15 mrem/yr above background to a resident in 50 years has been met. Four rounds of sampling, from pre-excavation to FSS, were performed as specified in the Field Sampling Plan (FSP) (BNL 2010a). It is the policy of the U.S. Department of Energy (DOE) to perform independent verifications of decontamination and decommissioning activities conducted at DOE facilities. ORISE has been designated as the organization responsible for this task for the HFBR Underground Utilities. ORISE, together with DOE, determined that a Type A verification of Trench 5 was appropriate based on recent verification results from Trenches 2, 3, and 4, and the minimal potential for residual radioactivity in the area. The removal of underground utilities is being performed in three stages to decommission the HFBR facility and support structures. Phase 3 of this project included the removal of at least 200 feet of 36-inch to 42-inch pipe from the west side to the south side of Building 801, and the 14-inch diameter Acid Waste Line that spanned from 801 to the Stack within Trench 5. Based on the pre-excavation sample results of the soil overburden the potential for contamination of the soil surrounding the pipe is minimal (BNL 2010a). ORISE reviewed the BNL FSP and identified comments for consideration (ORISE 2010). BNL prepared a revised FSP that resolved each ORISE comment adequately (BNL 2010a). ORISE referred to the revised HFBR Underground Utilities FSP FSS data to conduct the Type A verification

  8. Boulder Moves Ahead: An Evaluation of the English as a Second Language Tutorial Program of the Boulder Valley Public Schools, During Its First Year of Operation: 1975-76.

    Science.gov (United States)

    Stansfield, Charles

    The evaluation of the first year of the English as a Second Language Tutorial Program of Boulder Valley Public Schools included on-site observations, interviews with coordinators and teachers, a linguistic evaluation of each student (elementary and secondary levels), a classroom teacher's questionnaire, a parents' questionnaire, and a tutor's…

  9. A successful borehole drilled by cryogenic drilling in an arid, unconsolidated soil with boulders

    Energy Technology Data Exchange (ETDEWEB)

    Cavagnaro, P.; Simon, R.D.; Cooper, G.A. [Univ. of California, Berkeley, CA (United States). Dept. of Materials Science and Mineral Engineering

    1997-07-01

    An 80 foot deep borehole was drilled using a novel cryogenic drilling method. The freeze while drilling technique stabilizes the borehole wall while drilling by using conventional air rotary methods but with low temperature nitrogen gas (as cold as {minus}196 C) as the drilling fluid. The location of the field test was a semi-arid alluvial unconsolidated sedimentary formation at the Aerojet, Inc. site in Rancho Cordova, California. The geology was a sandy soil matrix containing cobbles and boulders. The test goal was to drill to 100 feet (30 m), but the test was terminated at 80 feet due to a failure of the swivel shaft and drill bit resulting from the very rough drilling conditions. No safety, technical, or operational problems were encountered that could prevent cryogenic drilling from becoming a standard technique for drilling in unstable near-surface formations.

  10. Boulder Deposits on the Southern Spanish Atlantic Coast: Possible Evidence for the 1755 AD Lisbon Tsunami?

    Directory of Open Access Journals (Sweden)

    Dieter Kelletat

    2005-01-01

    Full Text Available Field evidence of visible tsunami impacts in Europe is scarce. This research focused on an analysis of large littoral debris and accompanying geomorphic features and their rela- tionship to a tsunami event at Cabo de Trafalgar, located on the southern Spanish Atlantic coast. Relative dating of weathering features as well as minor bioconstructive forms in the littoral zone suggest the Lisbon tsunami of 1755 AD as the event responsible for the large deposits described. This tsunami had run up heights of more than 19 m and was generated at the Gorringe Bank, located 500 km west off the Cape. Tsunami deposits at Cabo de Tra- falgar are the first boulder deposits identified on the southern Spanish Atlantic coast and are located approximately 250 km southeast of the Algarve coast (Portugal, where other geo- morphic evidence for the Lisbon tsunami has been reported.

  11. Bouldering: an alternative strategy to long-vertical climbing in root-climbing hortensias.

    Science.gov (United States)

    Granados Mendoza, Carolina; Isnard, Sandrine; Charles-Dominique, Tristan; Van den Bulcke, Jan; Rowe, Nick P; Van Acker, Joris; Goetghebeur, Paul; Samain, Marie-Stéphanie

    2014-10-01

    In the Neotropics, the genus Hydrangea of the popular ornamental hortensia family is represented by climbing species that strongly cling to their support surface by means of adhesive roots closely positioned along specialized anchoring stems. These root-climbing hortensia species belong to the nearly exclusive American Hydrangea section Cornidia and generally are long lianescent climbers that mostly flower and fructify high in the host tree canopy. The Mexican species Hydrangea seemannii, however, encompasses not only long lianescent climbers of large vertical rock walls and coniferous trees, but also short 'shrub-like' climbers on small rounded boulders. To investigate growth form plasticity in root-climbing hortensia species, we tested the hypothesis that support variability (e.g. differences in size and shape) promotes plastic responses observable at the mechanical, structural and anatomical level. Stem bending properties, architectural axis categorization, tissue organization and wood density were compared between boulder and long-vertical tree-climbers of H. seemannii. For comparison, the mechanical patterns of a closely related, strictly long-vertical tree-climbing species were investigated. Hydrangea seemannii has fine-tuned morphological, mechanical and anatomical responses to support variability suggesting the presence of two alternative root-climbing strategies that are optimized for their particular environmental conditions. Our results suggest that variation of some stem anatomical traits provides a buffering effect that regulates the mechanical and hydraulic demands of two distinct plant architectures. The adaptive value of observed plastic responses and the importance of considering growth form plasticity in evolutionary and conservation studies are discussed. PMID:25079869

  12. Multi-method attribution analysis of extreme precipitation in Boulder, Colorado

    Science.gov (United States)

    Eden, Jonathan; van Oldenborgh, Geert Jan; Otto, Friederike

    2016-04-01

    Understanding and attributing the characteristics of extreme events that lead to societal impacts is a key challenge in climate science. Detailed analysis of individual case studies is particularly important in assessing how anthropogenic climate change is changing the likelihood of extreme events and their associated risk at relevant spatial scales. While climate model simulations provide an important basis for such analysis, reliable assessment of long term changes in extreme events is limited by models' inherent errors and biases. Here, we conduct a comprehensive multi-method attribution analysis of the heavy precipitation that led to widespread flooding in Boulder, Colorado in September 2013. Using extreme value analysis of, first of all, historical observations, we assess the influence of anthropogenic climate change on the likelihood of one- and five-day precipitation events across the Boulder area. The same analysis is extended to the output of a 16-member coupled model ensemble, following rigorous evaluation of the model skill in representing the processes responsible for extreme precipitation events in this region. Preliminary analysis using both observation- and model-based methods suggests that an event of this magnitude is around 20% more likely as a result of anthropogenic climate change. Recently, emphasis has been placed on the importance of model evaluation and bias correction in attribution studies. Further analysis will thus focus on sophisticated bias correction and downscaling techniques and their potential added value for application in attribution analysis. We also highlight the benefit of a multi-method approach in addressing event-specific attribution questions, particularly with regard to the quantification of uncertainty.

  13. Collection Assessment in Response to Changing Curricula: An Analysis of the Biotechnology Resources at the University of Colorado at Boulder

    Science.gov (United States)

    Wiersma, Gabrielle

    2010-01-01

    Increasing demand for biotechnology and biomedical resources prompted the Engineering Library at the University of Colorado at Boulder (UCB) to complete a collection assessment of the journals, books, and other resources provided by the University Libraries. This paper presents a variety of methods for evaluating library collections and describes…

  14. 33 CFR 165.T11-281 - Safety Zone; Lake Mead Intake Construction; Lake Mead, Boulder City, NV.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety Zone; Lake Mead Intake Construction; Lake Mead, Boulder City, NV. 165.T11-281 Section 165.T11-281 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PORTS AND WATERWAYS SAFETY REGULATED NAVIGATION AREAS AND LIMITED ACCESS AREAS...

  15. Deep crescentic features caused by subglacial boulder point pressure on jointed rock; an example from Virkisjökull, SE Iceland

    Science.gov (United States)

    Krabbendam, M.; Bradwell, T.; Everest, J.

    2012-04-01

    appear to be robust ice-flow indicators and indicate that former basal ice was rich in coarse, cobble/boulder-sized debris; • they are deeper and represent more significant erosion than previously reported crescentic features; during continuous subglacial erosion they thus (re)introduce a significant roughness on smoothed abraded surfaces, resulting in faster subglacial erosion; • assuming our proposed formation mechanism is correct, they could develop at lower stress (?thinner ice, [3]) than other crescentic features, as they utilise pre-existing weaknesses in the rock. The observations were made as part of the British Geological Survey's Virkisjökull Observatory Project. [1] Gilbert, GK, 1906. Bull. Geo. Soc. Am, v. 17, 303-313. [2] Harris, SE, 1943. J. Geology, v. 51, 244-258. [3] Wintges, T. 1985. J. Glaciology, v. 31, 340-349.

  16. The global size-frequency distribution of boulders > 7 m on Comet 67P Churyumov-Gerasimenko

    Science.gov (United States)

    Pajola, Maurizio; Baptiste Vincent, Jean; Lee, Jui-Chi; Ip, Wing-Huen; Lin, Zhong-Yi; Bertini, Ivano; Massironi, Matteo; Simioni, Emanuele; Barbieri, Cesare; Cremonese, Gabriele; Marzari, Francesco; Naletto, Giampiero; Giacomini, Lorenza; Jorda, Laurent; Thomas, Nicholas; Pommerol, Antoine; Kueppers, Michael; Moissl, Richard; Besse, Sebastien; Sierks, Holger

    2015-04-01

    After a ten years journey through the Solar System, the ESA Rosetta spacecraft reached on 6 August 2014 its primary target, the Jupiter family comet 67P/Churyumov-Gerasimenko, hereafter 67P. During the approaching phase, several images of the nucleus of comet 67P, captured by the OSIRIS scientific imaging camera, have been taken to study its structure, activity and the surface morphology. The close distance between spacecraft and comet, and the high resolution of our images, provided a unique opportunity to study features which could not have been detected before on other comets, but yet hold key parameters to derive the physical properties of the surface. We made use of the images acquired by the OSIRIS Narrow Angle Camera, NAC, on 5 and 6 August 2014 in order to study the statistical size-frequency distribution and the morphological properties of both clustered and isolated roundish structures ("boulders") scattered all over the currently illuminated side of the comet (70% of the total surface). Such dataset has been taken at a distance ranging between 131.45 and 109.76 km far from the comet center and the scale of these images (2.44 - 2.03 m/px) is such that boulders ≥ 7 m can be unequivocally identified and extracted. These images are the last ones where the entire comet is 2048 x 2048 pixels full frame and they cover a complete comet rotation (12.4 h), hence providing the possibility to derive a global size-frequency distribution statistics of the presently illuminated surface of 67P. A total amount of 3526 boulders has been identified on the surface of the comet: i) 2218 belonging to the big lobe, body, ii) 1115 boulders are located on the small lobe, head, while iii) 213 boulders belong to the transition region between the two lobes, called the neck. Here, global cumulative size-frequency distributions of boulders per square km are presented, together with specific and localized areas distributions. Moreover we indicate the different formation processes

  17. Nanoscale Compositional Relations in Lunar Rock Patina: Deciphering Sources for Patina Components on an Apollo 17 Station 6 Boulder

    Science.gov (United States)

    Christoffersen, R.; Noble, S. K.; Keller, L. P.

    2014-01-01

    Space weathering on the Moon and other airless bodies modifies the surfaces of regolith grains as well as the space-exposed surfaces of larger rocks and boulders. As space weathering witness plates, rocks and boulders are distinguished from regolith grains based on their ability to persist as physically intact substrates over longer time scales before being disaggregated by impact processes. Because lunar surfaces, including exposed rocks, quickly develop an optically thick layer of patina, it is important to understand the compositional relationship between patinas and their underlying rock substrates, particularly to support remote-sensing of rocky lunar terrains. Based on analytical TEM techniques, supported by focused ion beam (FIB) cross-sectioning, we have begun to systematize the multi-layer microstructural complexity of patinas on rock samples with a range of space exposure histories. Our on-going work has particularly focused on lunar rock 76015, both because it has a long (approx. 22 my) exposure history, and because its surface was exposed to patina development approximately 1 m off the regolith surface on a boulder in the Apollo 17 Station 6 boulder field. Potential sources for the 76015 patina therefore include impact-melted and vaporized material derived from the local rock substrate, as well as from the mix of large boulders and regolith in the Station 6 area. While similar, there are differences in the mineralogy and chemistry of the rocks and regolith at Station 6. We were interested to see if these, or other sources, could be distinguished in the average composition, as well as the compositional nanostratigraphy of the 76015 patina. To date we have acquired a total of 9 TEM FIB cross-sections from the 76015 patina, giving us reasonable confidence of being able to arrive at an integrated average for the patina major element composition based on analytical TEM methods.

  18. Arsenic and Antimony Removal from Drinking Water by Point-of-Entry Reverse Osmosis Coupled with Dual Plumbing Distribution - U.S. EPA Demonstration Project at Carmel Elementary School in Carmel, ME -Final Performance Evaluation Report

    Science.gov (United States)

    This report documents the activities performed for and the results obtained from the arsenic and antimony removal treatment technology demonstration project at the Carmel Elementary School (CES) in Carmel, ME. An innovative approach of employing point of entry (POE) reverse osmo...

  19. Arecibo and Goldstone radar evidence for boulders on near-Earth asteroids

    Science.gov (United States)

    Benner, L.; Nolan, M.; Brozovic, M.; Taylor, P.; Busch, M.; Howell, E.; Margot, J.; Giorgini, J.; Springmann, A.; Naidu, S.; Magri, C.; Shepard, M.

    2014-07-01

    plausible interpretation for these particular observations is that the bright pixels are echoes from surface and near-surface boulders, which have been seen on each of the three near-Earth asteroids imaged by spacecraft: (433) Eros (NEAR-Shoemaker), (25143) Itokawa (Hayabusa), and (4179) Toutatis (Chang'e 2). These asteroids have also been imaged by radar, but the resolutions and/or signal-to-noise ratios were insufficient to reveal possible boulders. Bright spots were not evident in radar images of Toutatis obtained between 1992-2008, but following an upgrade in Goldstone's finest resolution from 19 to 4 m/pixel in 2010, a modest number of spots became visible in Goldstone images of Toutatis obtained in 2012. The prevalence of small radar bright spots on numerous NEAs establishes that features consistent with boulders can be detected in delay-Doppler radar images of particularly high-SNR targets and that these features are relatively common on near-Earth asteroid surfaces.

  20. Erratic boulder trains and cosmogenic exposure dating of former glacial limits: A case-study from Tierra del Fuego, southernmost South America

    Science.gov (United States)

    Darvill, Christopher; Stokes, Chris; Bentley, Mike

    2014-05-01

    Erratic Boulder Trains (EBTs) are a spectacular yet poorly-understood glacial geomorphological feature. These linear clusters of glacial erratic boulders help to illustrate the flow-lines of former glaciers by pin-pointing the parent rock from which they have originated and are often used as targets for cosmogenic nuclide exposure dating. Consequently, there is a need to understand their geomorphological significance to improve ice-sheet reconstructions and provide important contextual information for dating studies. The EBTs in Tierra del Fuego are some of the finest examples of this feature in the world, and this paper presents the first comprehensive mapping and physical assessment of four boulder trains. Unlike most other examples, they were deposited laterally rather than medially and are tightly clustered, presenting linear features only a few kilometres long that contain hundreds to thousands of huge boulders (often >8 m in diameter). The size and angularity of the boulders strongly supports the hypothesis that they were deposited as a supraglacial rock avalanche. The boulders have been the subject of previous cosmogenic dating, which have yielded anomalously young ages from deposits thought to be hundreds of thousands of years old. Analysis of weathering proxies shows little difference between boulder trains thought to be of radically different ages, with important implications for the timing of glaciations and potentially contradicting previous age constraints on glacial limits in the region.

  1. Tick Removal

    Science.gov (United States)

    ... ticks Tickborne diseases abroad Borrelia miyamotoi Borrelia mayonii Tick Removal Recommend on Facebook Tweet Share Compartir If ... a tick quite effectively. How to remove a tick Use fine-tipped tweezers to grasp the tick ...

  2. Metal Removal in Wastewater

    OpenAIRE

    Sanchez Roldan, Laura

    2014-01-01

    The aim of this work was to study Copper removal capacity of different algae species and their mixtures from the municipal wastewater. This project was implemented in the greenhouse in the laboratories of Tampere University of Applied Sciences and the wastewater used was the one from the Tampere municipal wastewater treatment plant. Five algae species and three mixtures of them were tested for their Copper removal potential in wastewater in one batch test run. The most efficient algae mixture...

  3. The quantitative estimation of the vulnerability of brick and concrete wall impacted by an experimental boulder

    Science.gov (United States)

    Zhang, J.; Guo, Z. X.; Wang, D.; Qian, H.

    2016-02-01

    There is little historic data about the vulnerability of damaged elements due to debris flow events in China. Therefore, it is difficult to quantitatively estimate the vulnerable elements suffered by debris flows. This paper is devoted to the research of the vulnerability of brick and concrete walls impacted by debris flows. An experimental boulder (an iron sphere) was applied to be the substitute of debris flow since it can produce similar shape impulse load on elements as debris flow. Several walls made of brick and concrete were constructed in prototype dimensions to physically simulate the damaged structures in debris flows. The maximum impact force was measured, and the damage conditions of the elements (including cracks and displacements) were collected, described and compared. The failure criterion of brick and concrete wall was proposed with reference to the structure characteristics as well as the damage pattern caused by debris flows. The quantitative estimation of the vulnerability of brick and concrete wall was finally established based on fuzzy mathematics and the proposed failure criterion. Momentum, maximum impact force and maximum impact bending moment were compared to be the best candidate for disaster intensity index. The results show that the maximum impact bending moment seems to be most suitable for the disaster intensity index in establishing vulnerability curve and formula.

  4. Field evaluation of a two-dimensional hydrodynamic model near boulders for habitat calculation

    Science.gov (United States)

    Waddle, Terry

    2009-01-01

    Two-dimensional hydrodynamic models are now widely used in aquatic habitat studies. To test the sensitivity of calculated habitat outcomes to limitations of such a model and of typical field data, bathmetry, depth and velocity data were collected for three discharges in the vicinity of two large boulders in the South Platte River (Colorado) and used in the River2D model. Simulated depth and velocity were compared with observed values at 204 locations and the differences in habitat numbers produced by observed and simulated conditions were calculated. The bulk of the differences between simulated and observed depth and velocity values were found to lie within the likely error of measurement. However, the effect of flow simulation outliers on potential habitat outcomes must be considered when using 2D models for habitat simulation. Furthermore, the shape of the habitat suitability relation can influence the effects of simulation errors. Habitat relations with steep slopes in the velocity ranges found in similar study areas are expected to be sensitive to the magnitude of error found here. Comparison of habitat values derived from simulated and observed depth and velocity revealed a small tendency to under-predict habitat values.

  5. Field evaluation of a two-dimensinal hydrodynamic model near boulders for habitat calculation

    Science.gov (United States)

    Waddle, Terry

    2010-01-01

    Two-dimensional hydrodynamic models are now widely used in aquatic habitat studies. To test the sensitivity of calculated habitat outcomes to limitations of such a model and of typical field data, bathymetry, depth and velocity data were collected for three discharges in the vicinity of two large boulders in the South Platte River (Colorado) and used in the River2D model. Simulated depth and velocity were compared with observed values at 204 locations and the differences in habitat numbers produced by observed and simulated conditions were calculated. The bulk of the differences between simulated and observed depth and velocity values were found to lie within the likely error of measurement. However, the effect of flow simulation outliers on potential habitat outcomes must be considered when using 2D models for habitat simulation. Furthermore, the shape of the habitat suitability relation can influence the effects of simulation errors. Habitat relations with steep slopes in the velocity ranges found in similar study areas are expected to be sensitive to the magnitude of error found here. Comparison of habitat values derived from simulated and observed depth and velocity revealed a small tendency to under-predict habitat values.

  6. Fast Lemons and Sour Boulders: Testing Crossmodal Correspondences Using an Internet-Based Testing Methodology

    Directory of Open Access Journals (Sweden)

    Andy T. Woods

    2013-09-01

    Full Text Available According to a popular family of hypotheses, crossmodal matches between distinct features hold because they correspond to the same polarity on several conceptual dimensions (such as active–passive, good–bad, etc. that can be identified using the semantic differential technique. The main problem here resides in turning this hypothesis into testable empirical predictions. In the present study, we outline a series of plausible consequences of the hypothesis and test a variety of well-established and previously untested crossmodal correspondences by means of a novel internet-based testing methodology. The results highlight that the semantic hypothesis cannot easily explain differences in the prevalence of crossmodal associations built on the same semantic pattern (fast lemons, slow prunes, sour boulders, heavy red; furthermore, the semantic hypothesis only minimally predicts what happens when the semantic dimensions and polarities that are supposed to drive such crossmodal associations are made more salient (e.g., by adding emotional cues that ought to make the good/bad dimension more salient; finally, the semantic hypothesis does not explain why reliable matches are no longer observed once intramodal dimensions with congruent connotations are presented (e.g., visually presented shapes and colour do not appear to correspond.

  7. Stable isotopic records of bleaching and endolithic algae blooms in the skeleton of the boulder forming coral Montastraea faveolata

    OpenAIRE

    Hartmann, A.C.; Carilli, J. E.; Norris, R. D.; Charles, C. D.; Deheyn, D. D.

    2010-01-01

    Within boulder forming corals, fixation of dissolved inorganic carbon is performed by symbiotic dinoflagellates within the coral tissue and, to a lesser extent, endolithic algae within the coral skeleton. Endolithic algae produce distinctive green bands in the coral skeleton, and their origin may be related to periods of coral bleaching due to complete loss of dinoflagellate symbionts or “paling” in which symbiont populations are patchily reduced in coral tissue. Stable carbon isotopes were a...

  8. Modelling boulder impacts on deformable layers: role of rolling and toppling

    Science.gov (United States)

    Dattola, Giuseppe; Crosta, Giovanni; di Prisco, Claudio

    2016-04-01

    Rockfalls are apparently simple processes where few or no blocks interactions occur. Nevertheless, the extreme variability in the type of interactions between falling block and ground surface or material make the modelling of this phenomenon extremely complicated. To model the trajectories followed by a block falling along a slope it is crucial the adoption of laws capable of simulating the changes in block energy content due to impacts. The numerical simulation of impacts is thus fundamental for modelling block trajectories, assessing the risk associated with rockfall events and for designing sheltering structures. In this work, an extension of the hybrid model BIMPAM (di Prisco and Vecchiotti, 2006) in which block rotation is taken into account by adding another degree of freedom, is illustrated. The rheological model is developed assuming a lumped mass method. The additional kinematics variable enables the model not only to follow a more realistic trajectory but also to take into account additional dissipative mechanisms, which, in absence of the rotation, are absolutely neglected. These mechanisms are the block toppling and rolling. In this contribution, these mechanisms are modelled by the macro-element concept, and the delayed plasticity theory introducing two plastic sliders whose behaviors are described via two elasto-plastic constitutive laws. In order to illustrate the potentiality of this new version of the model a numerical parametric analysis, concerning in-clined trajectories on horizontal strata, is illustrated. The numerical results demonstrate that, in this new model version, the dissipated energy is increased and that during the impact a boulder spin originates, even in case the initial motion of the block is purely translational. This is opening a new set of possibilities and applications for rock fall modelling.

  9. A Re-Evaluation of the Relativistic Redshift on Frequency Standards at NIST, Boulder, Colorado, USA

    Science.gov (United States)

    Pavlis, N. K.; Weiss, M. A.

    2014-12-01

    Primary frequency standards that realize the definition of the second based on the Caesium (Cs) atom are used to steer International Atomic Time. According to the theory of relativity, their frequency should be adjusted to that at which these would operate, if located on the geoid. Current best standards for the current definition of the second are approaching uncertainties of one part in 1016. Optical frequency standards however are now reaching uncertainties of few parts in 1018 and are expected to lead to a new definition of the second. Their performance requires centimetre-level geoid accuracy, in order to calculate accurately the redshift frequency offset necessary for their inter-comparison. We re-evaluated the relativistic redshift of the frequency standards at NIST in Boulder, Colorado, USA, based on a recent precise GPS survey of several benchmarks on the roof of the building where these are housed, and on global and local geoid models supported by data from the GRACE and GOCE missions, including EGM2008, USGG2009, and USGG2012. We also evaluated the redshift offset based on the published NAVD88 geopotential number of the levelling benchmark Q407, after estimating the bias of the NAVD88 datum at our specific location. We present and discuss the results that we obtained using different methods, and provide our current estimate of the redshift offset and of its accuracy, considering the main error sources contributing to the total error budget. We compare our current estimates to those published by Pavlis and Weiss in 2003, using the data and models that were available at that time. We also discuss the prospects of using inter-connected ultra-precise frequency standards for the direct determination of geoid height differences, which may provide in the not-too-distant future an alternative approach for the establishment of vertical datums and the independent verification of the accuracy of global and local geoid models.

  10. Cobble cam: Grain-size measurements of sand to boulder from digital photographs and autocorrelation analyses

    Science.gov (United States)

    Warrick, J.A.; Rubin, D.M.; Ruggiero, P.; Harney, J.N.; Draut, A.E.; Buscombe, D.

    2009-01-01

    A new application of the autocorrelation grain size analysis technique for mixed to coarse sediment settings has been investigated. Photographs of sand- to boulder-sized sediment along the Elwha River delta beach were taken from approximately 1??2 m above the ground surface, and detailed grain size measurements were made from 32 of these sites for calibration and validation. Digital photographs were found to provide accurate estimates of the long and intermediate axes of the surface sediment (r2 > 0??98), but poor estimates of the short axes (r2 = 0??68), suggesting that these short axes were naturally oriented in the vertical dimension. The autocorrelation method was successfully applied resulting in total irreducible error of 14% over a range of mean grain sizes of 1 to 200 mm. Compared with reported edge and object-detection results, it is noted that the autocorrelation method presented here has lower error and can be applied to a much broader range of mean grain sizes without altering the physical set-up of the camera (~200-fold versus ~6-fold). The approach is considerably less sensitive to lighting conditions than object-detection methods, although autocorrelation estimates do improve when measures are taken to shade sediments from direct sunlight. The effects of wet and dry conditions are also evaluated and discussed. The technique provides an estimate of grain size sorting from the easily calculated autocorrelation standard error, which is correlated with the graphical standard deviation at an r2 of 0??69. The technique is transferable to other sites when calibrated with linear corrections based on photo-based measurements, as shown by excellent grain-size analysis results (r2 = 0??97, irreducible error = 16%) from samples from the mixed grain size beaches of Kachemak Bay, Alaska. Thus, a method has been developed to measure mean grain size and sorting properties of coarse sediments. ?? 2009 John Wiley & Sons, Ltd.

  11. Effects of slash removal in an experimental nitrogen gradient. Final report for the project; Effekter av biobraensleuttag i en experimentell kvaevegradient. Slutrapport foer projektet

    Energy Technology Data Exchange (ETDEWEB)

    Nohrstedt, H.Oe.; Ring, Eva; Sikstroem, Ulf; Hoegbom, Lars; Nordlund, Sten [Forestry Research Inst. of Sweden, Uppsala (Sweden)

    2000-04-01

    During four years after clear-felling, the effects of slash removal, including needles, were studied on a productive spruce site (site index G30) in the province of Vaermland, western Sweden. The study was made in an old fertilization experiment, in which at the most 2400 kg N/ha had been added during a twenty-year period. Despite the fact that the site is rich in nitrogen and that much slash was removed (100 ton d. m./ha), there were only very minor effects of the slash removal on the variables under study. These were the composition of soil water, the content of inorganic nitrogen in soil, the biomass of the field layer and the development of the planted spruce seedlings. The only statistically significant effect was that the content of nitrate was reduced in the humus layer. No data supported the idea that the previous fertilization influenced the effect of the slash removal, even though the fertilization had increased the content of total nitrogen in soil and the nitrogen leaching. Thus, we have not been able to repeat the observation from another Swedish study that slash removal reduces leaching of nitrogen and accompanying base cations, e. g. potassium. The effect of slash removal seems to depend on site conditions. Research is needed to reveal the variation in response and decisive factors. Our results, that the survival of spruce seedlings tends to be favoured by slash removal and that the early height growth is unaffected, are in accordance with results from previous studies. Our result, that the biomass of the total field layer is unaffected by slash removal, is not possible to compare with results from other studies, since these were mainly of a qualitative nature.

  12. Tattoo removal.

    Science.gov (United States)

    Adatto, Maurice A; Halachmi, Shlomit; Lapidoth, Moshe

    2011-01-01

    Over 50,000 new tattoos are placed each year in the United States. Studies estimate that 24% of American college students have tattoos and 10% of male American adults have a tattoo. The rising popularity of tattoos has spurred a corresponding increase in tattoo removal. Not all tattoos are placed intentionally or for aesthetic reasons though. Traumatic tattoos due to unintentional penetration of exogenous pigments can also occur, as well as the placement of medical tattoos to mark treatment boundaries, for example in radiation therapy. Protocols for tattoo removal have evolved over history. The first evidence of tattoo removal attempts was found in Egyptian mummies, dated to have lived 4,000 years BC. Ancient Greek writings describe tattoo removal with salt abrasion or with a paste containing cloves of white garlic mixed with Alexandrian cantharidin. With the advent of Q-switched lasers in the late 1960s, the outcomes of tattoo removal changed radically. In addition to their selective absorption by the pigment, the extremely short pulse duration of Q-switched lasers has made them the gold standard for tattoo removal.

  13. Tattoo removal.

    Science.gov (United States)

    Adatto, Maurice A; Halachmi, Shlomit; Lapidoth, Moshe

    2011-01-01

    Over 50,000 new tattoos are placed each year in the United States. Studies estimate that 24% of American college students have tattoos and 10% of male American adults have a tattoo. The rising popularity of tattoos has spurred a corresponding increase in tattoo removal. Not all tattoos are placed intentionally or for aesthetic reasons though. Traumatic tattoos due to unintentional penetration of exogenous pigments can also occur, as well as the placement of medical tattoos to mark treatment boundaries, for example in radiation therapy. Protocols for tattoo removal have evolved over history. The first evidence of tattoo removal attempts was found in Egyptian mummies, dated to have lived 4,000 years BC. Ancient Greek writings describe tattoo removal with salt abrasion or with a paste containing cloves of white garlic mixed with Alexandrian cantharidin. With the advent of Q-switched lasers in the late 1960s, the outcomes of tattoo removal changed radically. In addition to their selective absorption by the pigment, the extremely short pulse duration of Q-switched lasers has made them the gold standard for tattoo removal. PMID:21865802

  14. Economic Impacts from the Boulder County, Colorado, ClimateSmart Loan Program: Using Property-Assessed Clean Energy Financing

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, M.; Cliburn, J. K.; Coughlin, J.

    2011-04-01

    This report examines the economic impacts (including job creation) from the Boulder County, Colorado, ClimateSmart Loan Program (CSLP), an example of Property-Assessed Clean Energy (PACE) financing. The CSLP was the first test of PACE financing on a multi-jurisdictional level (involving individual cities as well as the county government). It was also the first PACE program to comprehensively address energy efficiency measures and renewable energy, and it was the first funded by a public offering of both taxable and tax-exempt bonds.

  15. Hair removal

    DEFF Research Database (Denmark)

    Haedersdal, Merete; Haak, Christina S

    2011-01-01

    Hair removal with optical devices has become a popular mainstream treatment that today is considered the most efficient method for the reduction of unwanted hair. Photothermal destruction of hair follicles constitutes the fundamental concept of hair removal with red and near-infrared wavelengths...... suitable for targeting follicular and hair shaft melanin: normal mode ruby laser (694 nm), normal mode alexandrite laser (755 nm), pulsed diode lasers (800, 810 nm), long-pulse Nd:YAG laser (1,064 nm), and intense pulsed light (IPL) sources (590-1,200 nm). The ideal patient has thick dark terminal hair......, white skin, and a normal hormonal status. Currently, no method of lifelong permanent hair eradication is available, and it is important that patients have realistic expectations. Substantial evidence has been found for short-term hair removal efficacy of up to 6 months after treatment with the available...

  16. Nevus Removal

    Science.gov (United States)

    ... can be fundamental to improving a patient’s overall psychosocial state. Other reasons to remove a nevus may ... This is not commonly done and presents many risks and challenges. Can’t they ... on all these same factors again. Different patients are more prone or less ...

  17. BWR Vessel and Internals Project Removal and Analysis of Material Samples from Core Shroud and Top Guide at Susquehanna Unit 2

    Energy Technology Data Exchange (ETDEWEB)

    Howell, D; Haertel, T; Lindberg, J; Oliver, B; Greenwood, L

    2005-04-15

    Fast and thermal fluence were determined by a laboratory analysis of the samples. Fluence in the upper regions of the shroud (between the H1 and H2 welds) was substantially lower than that in the belt line region (near the H4 weld). Fluence in the top guide was significantly higher than fluence on the core shroud. As expected, helium concentrations were highest in regions where fluence was highest. Estimates of the initial boron concentration were similar to measurements made on materials removed from other reactors. A technical justification evaluated the acceptability of the sampling process with respect to structural consequences of material removal and to increased cracking susceptibility due to the as-left condition. It was determined that the sampling process was acceptable on both counts.

  18. The southern hemisphere of 67P/Churyumov-Gerasimenko: Analysis of the preperihelion size-frequency distribution of boulders ≥7 m

    Science.gov (United States)

    Pajola, Maurizio; Lucchetti, Alice; Vincent, Jean-Baptiste; Oklay, Nilda; El-Maarry, Mohamed R.; Bertini, Ivano; Naletto, Giampiero; Lazzarin, Monica; Massironi, Matteo; Sierks, Holger; Barbieri, Cesare; Lamy, Philippe; Rodrigo, Rafael; Koschny, Detlef; Rickman, Hans; Keller, Horst U.; Agarwal, Jessica; A'Hearn, Michael F.; Barucci, Maria A.; Bertaux, Jean-Loup; Boudreault, Steve; Cremonese, Gabriele; Da Deppo, Vania; Davidsson, Björn; Debei, Stefano; De Cecco, Mariolino; Deller, Jakob; Fornasier, Sonia; Fulle, Marco; Gicquel, Adeline; Groussin, Olivier; Gutierrez, Pedro J.; Güttler, Carsten; Hofmann, Marc; Höfner, Sebastian; Hviid, Stubbe F.; Ip, Wing-Huen; Jorda, Laurent; Knollenberg, Jörg; Kramm, J.-Rainer; Kührt, Ekkehard; Küppers, Michael; La Forgia, Fiorangela; Lara, Luisa M.; Lee, Jui-Chi; Lin, Zhong-Yi; Lopez Moreno, Jose J.; Marzari, Francesco; Michalik, Harald; Mottola, Stefano; Preusker, Frank; Scholten, Frank; Thomas, Nicholas; Toth, Imre; Tubiana, Cecilia

    2016-07-01

    Aims: We calculate the size-frequency distribution of the boulders on the southern hemisphere of comet 67P Churyumov-Gerasimenko (67P), which was in shadow before the end of April 2015. We compare the new results with those derived from the northern hemisphere and equatorial regions of 67P, highlighting the possible physical processes that lead to these boulder size distributions. Methods: We used images acquired by the OSIRIS Narrow Angle Camera (NAC) on 2 May 2015 at a distance of 125 km from the nucleus. The scale of this dataset is 2.3 m/px; the high resolution of the images, coupled with the favorable observation phase angle of 62°, provided the possibility to unambiguously identify boulders ≥7 m on the surface of 67P and to manually extract them with the software ArcGIS. We derived the size-frequency distribution of the illuminated southern hemisphere. Results: We found a power-law index of -3.6 ± 0.2 for the boulders on the southern hemisphere with a diameter range of 7-35 m. The power-law index is equal to the one previously found on northern and equatorial regions of 67P, suggesting that similar boulder formation processes occur in both hemispheres. The power-law index is related to gravitational events triggered by sublimation and/or thermal fracturing causing regressive erosion. In addition, the presence of a larger number of boulders per km2 in the southern hemisphere, which is a factor of 3 higher with respect to the northern hemisphere, suggests that the southernmost terrains of 67P are affected by a stronger thermal fracturing and sublimating activity, hence possibly causing larger regressive erosion and gravitational events.

  19. Work plan, health and safety plan, and quality assurance project plan for hazardous waste removal at the CTF K-1654B underground collection tank

    Energy Technology Data Exchange (ETDEWEB)

    Panter, M.S.; Burman, S.N.; Landguth, D.C.; Uziel, M.S.

    1991-10-01

    The Central Training Facility (CTF), located on Bear Creek Road approximately two miles south of the K-25 Site, is utilized for training security personnel at Martin Marietta Energy Systems, Inc., Oak Ridge, Tennessee. At the request of the CTF staff, this plan has been developed for the removal of the waste contents in the facility's 500-gal septic tank and associated distribution box. The septic tank and distribution box were historically located beneath the K-1654B trailer and adjacent to the K-1654A Indoor Firing Range. Recently, however, the K-1654B trailer was removed to accommodate the objectives of this work plan as well as future construction activities planned at CTF. The purpose of this plan is to develop and assign responsibilities, establish personnel protection requirements and mandatory safety procedures, and provide for contingencies that may arise while operations are being conducted by ORNL/MAD at the CTF K-1654B underground collection tank site. This document addresses requirements of 29 CFR 1910.120, Final Rule, with respect to aspects of health and safety applicable to an underground collection tank waste removal.

  20. Removal of

    OpenAIRE

    Roohan Rakhshaee; Zahra Zamiraee; Somaieh Baghipour; Mohammad Panahandeh

    2013-01-01

    Background and Objectives: Azolla Filiculoides as a non-living fern was used in a batch system to remove "Basic Blue 3", which is a cationic dye and a carcinogenic agent.Materials and Methods: We used a batch system by applying certain concentrations of dye contaminant and in the presence of a certain amount of adsorbent under optimum conditions. The main groups presenting in the Azolla cell wall were evaluated by acidification and alkalization of Azolla's media and then potentiometric titrat...

  1. Hair Removal

    DEFF Research Database (Denmark)

    Hædersdal, Merete

    2011-01-01

    Hair removal with optical devices has become a popular mainstream treatment that today is considered the most efficient method for the reduction of unwanted hair. Photothermal destruction of hair follicles constitutes the fundamental concept of hair removal with red and near-infrared wavelengths ...... treatment procedures are evolving. Consumer-based treatments with portable home devices are rapidly evolving, and presently include low-level diode lasers and IPL devices....... suitable for targeting follicular and hair shaft melanin: normal mode ruby laser (694 nm), normal mode alexandrite laser (755 nm), pulsed diode lasers (800, 810 nm), long-pulse Nd:YAG laser (1,064 nm), and intense pulsed light (IPL) sources (590-1,200 nm). The ideal patient has thick dark terminal hair...... systems. Evidence has been found for long-term hair removal efficacy beyond 6 months after repetitive treatments with alexandrite, diode, and long-pulse Nd:YAG lasers, whereas the current long-term evidence is sparse for IPL devices. Treatment parameters must be adjusted to patient skin type...

  2. Removal of

    Directory of Open Access Journals (Sweden)

    Roohan Rakhshaee

    2013-02-01

    Full Text Available Background and Objectives: Azolla Filiculoides as a non-living fern was used in a batch system to remove "Basic Blue 3", which is a cationic dye and a carcinogenic agent.Materials and Methods: We used a batch system by applying certain concentrations of dye contaminant and in the presence of a certain amount of adsorbent under optimum conditions. The main groups presenting in the Azolla cell wall were evaluated by acidification and alkalization of Azolla's media and then potentiometric titration with standard basic and acidic solutions. Results: It was observed that the removal efficiency of dye using non-living Azolla in accordance with the Langmuir isotherms was 82% for the initial dye concentration of 200 mg/lit under reaction conditions consisting of contact time 6 h, pH= 6, temperature 25 ˚C, and dose 5 g/lit. Qmax (maximum uptake capacity by the activated Azolla at three temperatures 5, 25 and 50 ˚C was 0.732, 0.934, and 1.176 mmol/g respectively. ΔG (Gibbs free energy changes was obtained for these temperatures as -0.457, -0.762, and -1.185 kJ/mol respectively.Conclusion: Removal of basic blue 3 using Azolla is an economically and effective method.

  3. 75 FR 13232 - Safety Zone; Lake Mead Intake Construction, Lake Mead, Boulder City, NV

    Science.gov (United States)

    2010-03-19

    ... SECURITY Coast Guard 33 CFR Part 165 RIN 1625-AA00 Safety Zone; Lake Mead Intake Construction, Lake Mead... establishing a safety zone on the navigable waters of Lake Mead in support of the construction project for Lake... ensure the public's safety. Background and Purpose Vegas Tunnel Construction will be...

  4. Coastal vulnerability to typhoon inundation in the Bay of Bangkok, Thailand? Evidence from carbonate boulder deposits on Ko Larn island

    Science.gov (United States)

    Terry, James P.; Jankaew, Kruawun; Dunne, Kieran

    2015-11-01

    At the head of the Gulf of Thailand, the subsiding Chao Phraya delta and adjacent low-lying coastlines surrounding the Bay of Bangkok are at risk of coastal flooding. Although a significant marine inundation event has not been experienced in historical times, this work identifies coastal depositional evidence for high-energy waves in the past. On Ko Larn island in eastern Bay of Bangkok, numerous coastal carbonate boulders (CCBs) were discovered at elevations up to 4+ m above sea level, the largest weighing over 1.3 tonnes. For the majority of CCBs, their karstified appearance bears testimony to long periods of immobility since original deposition, whilst their geomorphic settings on coastal slopes of coarse blocky talus is helpful in recognising lifting (saltation) as the probable mode of wave transport. In the absence of local tsunamigenic potential, these CCBs are considered to be prehistoric typhoon deposits, presumably sourced from fringing coral reefs by high-energy wave action. Application of existing hydrodynamic flow transport equations reveals that 4.7 m/s and 7.1 m/s are the minimum flow velocities required to transport 50% and 100% of the measured CCBs, respectively. Such values are consistent with cyclone-impacted coastlines studied elsewhere in the tropical Asia-Pacific region. Overall, the evidence of elevated carbonate boulder deposits on Ko Larn implies that typhoons before the modern record may have entered the Bay of Bangkok. The recurrence of a similar event in future would have the potential to cause damaging marine inundation on surrounding low-lying coastlines.

  5. Results of the Boulder Consultation: The Beginnings of a Technical Assistance Program for the Office of Environmental Education/USOE/HEW.

    Science.gov (United States)

    Office of Education (DHEW), Washington, DC. Office of Environmental Education.

    In December 1977, the Office of Environmental Education (OEE) brought its fiscal year '77 grant recipients together in Boulder, Colorado, for a technical assistance consultation. The technical assistance responsibilities of OEE are mandated by the Environmental Education Act. Until this consultation, OEE had been giving its technical assistance on…

  6. Captive propagation, reproductive biology, and early life history of Etheostoma wapiti (Boulder Darter), E. vulneratum (Wounded Darter), and E. maculatum (Spotted Darter)

    Science.gov (United States)

    Ruble, Crystal L.; Rakes, Patrick L.; Shute, John R.; Welsh, Stuart

    2016-01-01

    Reproductive biology and early life-history data are important for understanding the ecology of fishes. In 2008, we conducted captive propagation studies on 3 species of darters of the subgenus Nothonotus: Etheostoma wapiti (Boulder Darter), E. vulneratum (Wounded Darter), and E. maculatum (Spotted Darter). The length of spawning period and associated range of water temperatures for the Wounded Darter exceeded that of the Spotted Darter and Boulder Darter. The mean number of eggs produced per female was lowest for Boulder Darter and highest in the Wounded Darter. The Boulder Darter had the highest percent of eggs hatched, the lowest percent larval to juvenile stage survivorship, and the lowest mean number of juveniles produced per female. Egg diameters at deposition and prior to hatch were smallest for the Spotted Darter. If reproductive biology and early lifehistory information from captive fishes represent that of wild populations, then the data obtained during this study are relevant to development and implementation of conservation and management plans for these closely related darter species.

  7. Analysis of Cost Control of Wuding Jiyi Reservoir Danger-removing and Strengthening Project%武定己衣水库除险加固工程施工成本控制浅析

    Institute of Scientific and Technical Information of China (English)

    奉丽玲; 姜泽侯; 韩春秀; 赵发宾

    2013-01-01

    Through the description to Wuding Jiyi reservoir danger-removing and strengthening project cost control of success experience, on a conservancy project construction cost of main composition factors for has discussion, Find the key to cost control such as to strengthen the site construction management, and effective of scheduling machinery equipment, and strictly control raw materials, and reasonable adjustment of personnel. On the premise of safety and quality, created out better of economic benefits. For similar construction projects to improve cost control has a positive experience.%  本文结合武定己衣水库除险加固工程的实例,总结了施工成本控制的成功经验,对水利工程施工成本的主要组成因素进行了探讨,找出成本控制的关键点,提出加强现场施工管理、有效的调度机械设备、严格控制原材料、合理调配人员等具体措施,在安全生产和质量优良的前提下,创造出更好的经济效益。对类似水利工程施工项目提高成本控制能力具有积极的借鉴作用。

  8. Study of Catalysts and Electrocatalysts for NO{sub x} Removal in Combustion Gases ELECTRONOX Project Final Report; Estudio de Catalizadores y Electrocatalizadores para la Eliminacion de NO{sub x} en Gases de Combustion. Informe Final Proyecto ELECTRONOX

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz Martinez, E.; Marono Bujan, M.; Sanchez-Hervas, J. M.

    2009-12-11

    The final aim of the ELECTRONOX project was to develop new methodologies and technologies for NO{sub x} removal. To fulfil this objective, studies of selective catalytic reduction of NO{sub x} with hydrocarbons, both conventional and with electrochemical promotion, have been undertaken at pilot plant level, using appropriate catalyst/electrocatalysts configurations and in conditions similar to those required in their possible practical application. None of the catalysts/electrocatalysts studied is active and stable enough, under realistic conditions, to consider its possible industrial application, because the value of NO{sub x} conversion achieved by selective catalytic reduction with hydrocarbons, both conventional and with electrochemical promotion, decreases in presence of the different inhibitors and poisons present in the combustion gas, while the promotional effect on the catalytic activity and selectivity is more pronounced. In addition, the catalysts/electrocatalysts suffer from different deactivation processes, such as: sulphur poisoning, carbon deposition and sintering. However, the developed electrochemical catalyst looks promising for NO{sub x} removal in combustion gases, because it can be promoted under realistic operating conditions. (Author) 23 refs.

  9. The effect of variable discharge on the inorganic chemistry downstream of a waste water treatment plant, Boulder Creek, Colorado

    Science.gov (United States)

    Antweiler, R. C.; Writer, J. H.; Murphy, S. F.

    2012-12-01

    Researchers investigating the effect of wastewater treatment plant (WWTP) effluent on streams often assume that the magnitude of this effect is constant over time. However, discharge of WWTP effluent frequently follows a distinctive diel pattern. WWTP effluent discharge into Boulder Creek, Colorado, for example, varies by almost 200% over the course of a day. Due to this variation, downstream concentrations of chloride, boron and gadolinium (commonly used "conservative tracers") exhibit major changes over a 24-hour period. In order to determine how effluent discharge variability affects stream chemistry, we performed an evaluation of discharge and inorganic chemistry of the City of Boulder's WWTP and Boulder Creek upstream and downstream of the WWTP (representing a 5.4-km reach). Sodium bromide and Rhodamine WT were used to confirm that the same parcel of water was sampled as it moved downstream. The behavior of inorganic constituents fell into three distinct categories, showing conservative behavior, in-stream loss, or in-stream gain. Accounting for variable effluent discharge, the following inorganic constituents behaved conservatively: Cl, SO4, HCO3, F, B, Ba, Ca, Gd, K, Mg, Rb, Co, Cu, Mo, NO3, P and PO4, Sb, SiO2, Sr and Zn. Inorganic compounds which showed evidence of in-stream loss were Bi, Cr, Cs, Ga, Ge, Hg, Se, and Sn. For these elements, the typical pattern was an almost immediate loss: by the time the water had traveled to the first downstream sampling site, 2.3-km below the WWTP, in-stream reactions appeared to have ceased, and a constant flux was observed at all subsequent sites. We speculate that the near-immediate rates represent precipitation and/or adsorption caused by the change in pH and temperature of the mixing zone. Inorganic constituents that showed evidence of in-stream gain were: Al, As, Cd, Fe, I, Li, Mn, Nb, Pb, Re, Th, U, V, W, and all the rare-earth elements (except Gd). As with the in-stream loss group, most of the reactions occurred

  10. High Spatial Resolution 40Ar/39Ar Geochronology of Impact Melt Breccias from Apollo 17 Boulders at Stations 2, 6, and 7

    Science.gov (United States)

    Mercer, C. M.; Hodges, K. V.; Jolliff, B. L.; Van Soest, M. C.; Wartho, J. A.; Weirich, J. R.

    2015-12-01

    Several boulders located at the bases of the North and South Massifs were among the primary field targets of the Apollo 17 mission to the Taurus-Littrow Valley on the Moon [1]. Some boulders are polylithologic, including Boulder 1 at Station 2 and the boulders at Stations 6 and 7. These boulders were the subjects of consortium studies [2, 3] that included 40Ar/39Ar geochronology to determine the ages of distinct lithologies within each boulder [e.g., 4-6]. We report new 40Ar/39Ar data for the impact melt breccias 72255, 76315, 77075, and 77135 obtained using the UV laser ablation microprobe (UVLAMP) methods of [7]. For 72255, we obtained a preliminary isochron date ca. 3814 Ma from 22 melt analyses, which is younger than published plateau dates (e.g., 3951-3835 Ma [4, 8]). Fifteen melt analyses of 76315 yield a preliminary isochron date ca. 3850 Ma, younger than the 3900 ± 16 Ma date reported by [8]. Melt analyses of 77075 yield preliminary dates between ca. 3797-3584 Ma, possibly reflecting partial loss of 40Ar. In this case, the oldest date may provide a minimum age for the formation of melt in 77075. Finally, the UVLAMP dates for the 77135 melt range from 3810-3361 Ma and corresponding Ca/K ratios range from ca. 100-6. Electron microprobe analyses of small (ca. 10s of microns wide) pockets of K-rich materials show that both K-rich glass and K-feldspar are present. The UVLAMP dates for 77135 likely reflect spatially variable 40Ar loss, consistent with published step heating results [e.g., 6]. References: [1] Schmitt (1973) Science, 182, 681-690. [2] Ryder (1993). Catalog of Apollo 17 Rocks: Volume 1 - Stations 2 and 3 (South Massif). LPI. [3] Ryder (1993). Catalog of Apollo 17 Rocks: Volume 4 - North Massif. LPI. [4] Leich et al. (1975) The Moon, 14, 407-444. [5] Cadogan & Turner (1976). LPSC, 7, 2267-2285. [6] Stettler et al. (1978). LPSC, 9, 1113-1115. [7] Mercer et al. (2015) Sci. Adv., 1, e1400050. [8] Dalrymple & Ryder (1996). JGR, 101, 26069-26084.

  11. Superfund TIO videos. Set A. Removal process: Planning and initiating removals, managing removals, non-CERCLA funded removals. Part 3 Audio-Visual

    International Nuclear Information System (INIS)

    The videotape is divided into three sections. Section 1 outlines the major components of planning and initiating a removal, such as identifying appropriate response actions, preparing an Action Memorandum (AM), projecting the cost of the removal, obtaining site access, setting up a command post, and overseeing the development of the required plans. The resources available to the OSC to conduct a removal also are discussed. Section 2 discusses the OSC's role in managing the removal and describes how to obtain resources and how to manage site activities and monitor costs. The statutory limits of a removal and the importance of documenting site activities accurately and completely also are outlined. Section 3 outlines the OSC's role in removal actions conducted by parties other than EPA OSCs. Discussed are CERCLA removals conducted by PRPs, States, Federal facilities and Indian tribes. Underground Storage Tank (UST) assessment and removal under Resource Conservation and Recovery Act (RCRA) authority is also discussed

  12. Stable isotopic records of bleaching and endolithic algae blooms in the skeleton of the boulder forming coral Montastraea faveolata

    Science.gov (United States)

    Hartmann, A. C.; Carilli, J. E.; Norris, R. D.; Charles, C. D.; Deheyn, D. D.

    2010-12-01

    Within boulder forming corals, fixation of dissolved inorganic carbon is performed by symbiotic dinoflagellates within the coral tissue and, to a lesser extent, endolithic algae within the coral skeleton. Endolithic algae produce distinctive green bands in the coral skeleton, and their origin may be related to periods of coral bleaching due to complete loss of dinoflagellate symbionts or “paling” in which symbiont populations are patchily reduced in coral tissue. Stable carbon isotopes were analyzed in coral skeletons across a known bleaching event and 12 blooms of endolithic algae to determine whether either of these types of changes in photosynthesis had a clear isotopic signature. Stable carbon isotopes tended to be enriched in the coral skeleton during the initiation of endolith blooms, consistent with enhanced photosynthesis by endoliths. In contrast, there were no consistent δ13C patterns directly associated with bleaching, suggesting that there is no unique isotopic signature of bleaching. On the other hand, isotopic values after bleaching were lighter 92% of the time when compared to the bleaching interval. This marked drop in skeletal δ13C may reflect increased kinetic fractionation and slow symbiont recolonization for several years after bleaching.

  13. Flash Flood Risks and Warning Decisions: A Mental Models Study of Forecasters, Public Officials, and Media Broadcasters in Boulder, Colorado.

    Science.gov (United States)

    Morss, Rebecca E; Demuth, Julie L; Bostrom, Ann; Lazo, Jeffrey K; Lazrus, Heather

    2015-11-01

    Timely warning communication and decision making are critical for reducing harm from flash flooding. To help understand and improve extreme weather risk communication and management, this study uses a mental models research approach to investigate the flash flood warning system and its risk decision context. Data were collected in the Boulder, Colorado area from mental models interviews with forecasters, public officials, and media broadcasters, who each make important interacting decisions in the warning system, and from a group modeling session with forecasters. Analysis of the data informed development of a decision-focused model of the flash flood warning system that integrates the professionals' perspectives. Comparative analysis of individual and group data with this model characterizes how these professionals conceptualize flash flood risks and associated uncertainty; create and disseminate flash flood warning information; and perceive how warning information is (and should be) used in their own and others' decisions. The analysis indicates that warning system functioning would benefit from professionals developing a clearer, shared understanding of flash flood risks and the warning system, across their areas of expertise and job roles. Given the challenges in risk communication and decision making for complex, rapidly evolving hazards such as flash floods, another priority is development of improved warning content to help members of the public protect themselves when needed. Also important is professional communication with members of the public about allocation of responsibilities for managing flash flood risks, as well as improved system-wide management of uncertainty in decisions. PMID:25988286

  14. Health hazard evaluation report HETA 86-157-1678, Stag Dental Clinic, Boulder, Colorado. [Nitrous oxide exposure

    Energy Technology Data Exchange (ETDEWEB)

    Gunter, B.J.

    1986-03-01

    Employees of the Stag Dental Clinic, Boulder, Colorado requested an evaluation of nitrous oxide exposure during dental procedures. Direct reading measurements taken in the dental operatory immediately after nitrous oxide was administered showed levels exceeding 1000 parts per million (ppm) in the breathing zone of the dentist and his assistant. The levels remained high throughout the 1-hour procedure. The level of nitrous oxide in the hallway outside the operatory was 300 ppm and that in the adjacent operatory, 150 ppm (background). General-room air in the operatory in use was 800 ppm nitrous oxide. Levels of nitrous oxide decreased to 50 ppm 1.5 hours after the gas was turned off. The current NIOSH recommended time weighted average is 25 ppm. The author concludes that a health hazard existed at the dental office due to high exposures of nitrous oxide. It was recommended that a scavenging system should be installed. Recommendations also include routine maintenance on anesthetic and suction equipment, a follow-up evaluation after the exhaust systems have been in place, advising all dentists and other personnel in the clinic of the adverse health effects due to nitrous oxide, and use of more dilution ventilation.

  15. Stable isotopic records of bleaching and endolithic algae blooms in the skeleton of the boulder forming coral Montastraea faveolata

    OpenAIRE

    Hartmann, A.C.; Carilli, J. E.; Norris, R. D.; Charles, C. D.; Deheyn, D. D.

    2010-01-01

    Within boulder forming corals, fixation of dissolved inorganic carbon is performed by symbiotic dinoflagellates within the coral tissue and, to a lesser extent, endolithic algae within the coral skeleton. Endolithic algae produce distinctive green bands in the coral skeleton, and their origin may be related to periods of coral bleaching due to complete loss of dinoflagellate symbionts or ‘‘paling’’ in which symbiont populations are patchily reduced in coral tissue. Stable carbon isotopes were...

  16. Effects of Controllable Blasting Variables on Number of Boulders Generated after Blasting in Ratcon and NSCE Quarries, Ibadan, Oyo State, Nigeria

    OpenAIRE

    Abiodun Ismail LAWAL; Akande Jide Muili

    2013-01-01

    The research work examines the effects of controllable blasting variables on number of boulders generated after blasting. The objective of the research was achieved through collection of data related to blasting which are drill hole depth, drill hole diameter, burden, spacing, average charge per hole, and specific charge. The collected data were analysed statistically using both Microsoft Excel Software and SPSS Software. The result of the analysis reveals that all the input controllable blas...

  17. Geomorphology and weathering characteristics of erratic boulder trains on Tierra del Fuego, southernmost South America: Implications for dating of glacial deposits

    Science.gov (United States)

    Darvill, Christopher M.; Bentley, Michael J.; Stokes, Chris R.

    2015-01-01

    Erratic boulder trains (EBTs) are a useful glacial geomorphological feature because they reveal former ice flow trajectories and can be targeted for cosmogenic nuclide exposure dating. However, understanding how they are transported and deposited is important because this has implications for palaeoglaciological reconstructions and the pre-exposure and/or erosion of the boulders. In this study, we review previous work on EBTs, which indicates that they may form subglacially or supraglacially but that large angular boulders transported long distances generally reflect supraglacial transport. We then report detailed observations of EBTs from Tierra del Fuego, southernmost South America, where their characteristics provide a useful framework for the interpretation of previously published cosmogenic nuclide exposure dates. We present the first comprehensive map of the EBTs and analyse their spatial distribution, size, and physical appearance. Results suggest that they were produced by one or more supraglacial rock avalanches in the Cordillera Darwin and were then transported supraglacially for 100 s of kilometres before being deposited. Rock surface weathering analysis shows no significant difference in the weathering characteristics of a sequence of EBTs, previously hypothesized to be of significantly different age (i.e., different glacial cycles). We interpret this to indicate that the EBTs are much closer in age than previous work has implied. This emphasises the importance of understanding EBT formation when using them for cosmogenic nuclide exposure dating.

  18. Effects of Controllable Blasting Variables on Number of Boulders Generated after Blasting in Ratcon and NSCE Quarries, Ibadan, Oyo State, Nigeria

    Directory of Open Access Journals (Sweden)

    Abiodun Ismail LAWAL

    2013-03-01

    Full Text Available The research work examines the effects of controllable blasting variables on number of boulders generated after blasting. The objective of the research was achieved through collection of data related to blasting which are drill hole depth, drill hole diameter, burden, spacing, average charge per hole, and specific charge. The collected data were analysed statistically using both Microsoft Excel Software and SPSS Software. The result of the analysis reveals that all the input controllable blasting variables which are drill hole diameter (X1, drill hole depth (X2, hole spacing (X3, burden (X4, average charge per hole (X5, specific charge(X6 that participated as independent variables in the models are found to be significant and the R2 values obtained from the graph show a very strong correlation between the number of boulders generated after blasting and the input variables except that of drill hole diameter which shows a very weak correlation. The equation generated using the SPSS could be used to determine number of boulders generated after blasting.

  19. Periglacial Slope Deposits and Saprolites Controlling Water Discharge. Examples From the Bavarian Forest, Germany and Boulder Creek (CZO), Colorado, USA

    Science.gov (United States)

    Huber, J.; Huerkamp, K.; Voelkel, J.; Leopold, M.

    2008-12-01

    investigations in the Colorado Front Range at Boulder.

  20. Comparison of modeled NmE with NmE measured by the Boulder ionosonde near the spring equinox.

    Science.gov (United States)

    Pavlov, Anatoli; Pavlova, Nadezhda

    We present a comparison of the E-layer peak electron number densities, NmE, measured by the Boulder ionosonde during geomagnetically quiet conditions on 10 April 1996 at low solar activity, 2 April 1993 and 9 April 1978 during moderate solar activity conditions, and 10 April 1991 at high solar activity with numerical theoretical model calculations of NmE. Based on this comparison, the modified EUVAC model solar flux is necessary to increase by a factor of 2 at moderate and high solar activity in the wavelength range of 3.2-7.0 nm. If O (+) ( (4) S), O (+) ( (2) D), O (+) ( (2) P), and N (+) ions are not calculated, the value of NmE is decreased up to a factor of 1.12 at solar minimum and up to a factor of 1.23 for the moderate and high solar activity conditions. The production of N _{2} (+) ions by photoelectron-impact ionization of N _{2} increases the value of NmE up to a factor of 1.18 at low solar activity and up to a factor of 1.33 for the moderate and high solar activity levels. The increase in NmE due to the production of O _{2} (+) ions by photoelectron-impact ionization of O _{2} does not exceed 4 percent. A difference between the calculated electron, T _{e}, and neutral, T _{n}, temperatures is less than 1, 4, 20, 70, and 145 K at 105, 110, 120, 130, and 140 km altitude, respectively. Changes in NmE caused by this difference between T _{e} and T _{n} are negligible.

  1. Comparison of NmE measured by the boulder ionosonde with model predictions near the spring equinox

    Science.gov (United States)

    Pavlov, A. V.; Pavlova, N. M.

    2013-09-01

    We present a comparison of the E-layer peak electron number densities, NmE, measured by the Boulder ionosonde during geomagnetically quiet conditions on 10 April 1996 at low solar activity, 2 April 1993 and 9 April 1978 during moderate solar activity conditions, and 10 April 1991 at high solar activity with numerical theoretical model calculations of NmE. Based on this comparison, the EUVAC model solar flux is necessary to increase by a factor of 2 at moderate and high solar activity in the wavelength range of 3.2-7.0 nm. If O+(4S), O+(2D), O+(2P), and N+ ions are not calculated, the value of NmE is decreased up to a factor of 1.12 at solar minimum and up to a factor of 1.23 for the moderate and high solar activity conditions. The production of N2+ ions by photoelectron-impact ionization of N2 increases the value of NmE up to a factor of 1.18 at low solar activity and up to a factor of 1.33 for the moderate and high solar activity levels. The increase in NmE due to the production of O2+ ions by photoelectron-impact ionization of O2 does not exceed 4%. A difference between the calculated electron, Te, and neutral, Tn, temperatures is less than 1, 4, 20, 70, and 145 K at 105, 110, 120, 130, and 140 km altitude, respectively. Changes in NmE caused by this difference between Te and Tn are negligible.

  2. Trends and variability of midlatitude stratospheric water vapour deduced from the re-evaluated Boulder balloon series and HALOE

    Directory of Open Access Journals (Sweden)

    M. Scherer

    2007-10-01

    Full Text Available This paper presents an updated trend analysis of water vapour in the lower midlatitude stratosphere from the Boulder balloon-borne NOAA frostpoint hygrometer measurements and from the Halogen Occulation Experiment (HALOE. Two corrections for instrumental bias are applied to homogenise the frostpoint data series, and a quality assessment of all soundings after 1991 is presented. Linear trend estimates based on the corrected data for the period 1980–2000 are up to 40% lower than previously reported. Vertically resolved trends and variability are calculated with a multi regression analysis including the quasi-biennal oscillation and equivalent latitude as explanatory variables. In the range of 380 to 640 K potential temperature (≈14 to 25 km, the frostpoint data from 1981 to 2006 show positive linear trends between 0.3± 0.3 and 0.7±0.1%/yr. The same dataset shows trends between −0.2±0.3 and 1.0±0.3%/yr for the period 1992 to 2005. HALOE data over the same time period suggest negative trends ranging from −1.1±0.2 to −0.1±0.1%/yr. In the lower stratosphere, a rapid drop of water vapour is observed in 2000/2001 with little change since. At higher altitudes, the transition is more gradual, with slowly decreasing concentrations between 2001 and 2007. This pattern is consistent with a change induced by a drop of water concentrations at entry into the stratosphere. Previously noted differences in trends and variability between frostpoint and HALOE remain for the homogenised data. Due to uncertainties in reanalysis temperatures and stratospheric transport combined with uncertainties in observations, no quantitative inference about changes of water entering the stratosphere in the tropics could be made with the mid latitude measurements analysed here.

  3. Trends and variability of midlatitude stratospheric water vapour deduced from the re-evaluated Boulder balloon series and HALOE

    Directory of Open Access Journals (Sweden)

    M. Scherer

    2008-03-01

    Full Text Available This paper presents an updated trend analysis of water vapour in the lower midlatitude stratosphere from the Boulder balloon-borne NOAA frostpoint hygrometer measurements and from the Halogen Occulation Experiment (HALOE. Two corrections for instrumental bias are applied to homogenise the frostpoint data series, and a quality assessment of all soundings after 1991 is presented. Linear trend estimates based on the corrected data for the period 1980–2000 are up to 40% lower than previously reported. Vertically resolved trends and variability are calculated with a multi regression analysis including the quasi-biennal oscillation and equivalent latitude as explanatory variables. In the range of 380 to 640 K potential temperature (≈14 to 25 km, the frostpoint data from 1981 to 2006 show positive linear trends between 0.3±0.3 and 0.7±0.1%/yr. The same dataset shows trends between −0.2±0.3 and 1.0±0.3%/yr for the period 1992 to 2005. HALOE data over the same time period suggest negative trends ranging from −1.1±0.2 to −0.1±0.1%/yr. In the lower stratosphere, a rapid drop of water vapour is observed in 2000/2001 with little change since. At higher altitudes, the transition is more gradual, with slowly decreasing concentrations between 2001 and 2007. This pattern is consistent with a change induced by a drop of water concentrations at entry into the stratosphere. Previously noted differences in trends and variability between frostpoint and HALOE remain for the homogenised data. Due to uncertainties in reanalysis temperatures and stratospheric transport combined with uncertainties in observations, no quantitative inference about changes of water entering the stratosphere in the tropics could be made with the mid latitude measurements analysed here.

  4. CO2 Removal from Mars EMU Project

    Data.gov (United States)

    National Aeronautics and Space Administration — CO2 control for during ExtraVehicular Activity (EVA) on mars is challenging. Lithium hydroxide (LiOH) canisters have impractical logistics penalties, and...

  5. CO2 Removal from Mars EMU Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A practical CO2 control system for ExtraVehicular Activity (EVA) on Mars have not yet been developed. TDA Research, Inc. proposes to develop a durable,...

  6. SUMMARY AND RESULTS LETTER REPORT - INDEPENDENT VERIFICATION OF THE HIGH FLUX BEAM REACTOR UNDERGROUND UTILITIES REMOVAL PROJECT, PHASE 3: TRENCHES 2, 3, AND 4 BROOKHAVEN NATIONAL LABORATORY UPTON, NEW YORK

    International Nuclear Information System (INIS)

    Oak Ridge Institute for Science and Education (ORISE) personnel visited the Brookhaven National Laboratory (BNL) on September 7 through September 10, 2010, and September 20 through Seeptember 24, 2010. ORISE performed visual inspections, conducted independent measurement, and sampling of Trenches 2, 3, and 4, which are part of Phase 3 for the High Flux Beam Reactor (HFBR) Underground Utilities Removal Project. Trenches 2 and 3 were addressed during the first visit and Trench 4 during the second visit to BNL. Spatial orientation to Building 801 and minimal survey area inside Trenches 2 and 3 limited satellite reception and the ability to utilize a global positioning system (GPS) as real-time data capture for the gamma scan surveys in these trenches. However, Trench 4 provided suitable conditions in which gamma scan data could be collected using the GPS. ORISE performed high-density gamma scans of accessible surface areas using shielded sodium iodide detectors coupled to ratemeter-scalers with audible output. Scans for Trench 2 ranged from 4,000 to 22,000 gross counts per minute (cpm); Trench 3 from 3,000 to 5,000 gross cpm and Trench 4 from 2,600 to 9,500 gross cpm. ORISE personnel flagged the area where the elevated counts were observed in Trench 2 for further investigation. Additional scane valuations were performed on remaining pipes and associated end-caps in the trenches with no elevated activity detected. Eleven judgemental soil samples (5098M0041 through 5098M0051) were obtained throughout Trenches 2, 3, and 4. The sample locations were selected based on count rates observed during the scan survey or because of contamination potential from pipeline removal activities. ORISE personnel judgmentally selected the location for sample M0043 in response to the 22,000 cpm observed during the scan survey, and to ascertain whether the elevataed counts were a result of soil contamination or radioactive shine from the trench's spatial orientation to the Target Room in

  7. Spatial patterns of mobile regolith thickness and meteoric 10Be in the Boulder Creek Critical Zone Observatory, Front Range, Colorado

    Science.gov (United States)

    Shea, N.; Ouimet, W. B.; Dethier, D. P.; Bierman, P. R.; Rood, D. H.

    2012-12-01

    The Boulder Creek Critical Zone Observatory (BcCZO) aims to understand the history, architecture and evolution of hillslopes found within the diverse topography and climate regimes of the Colorado Front Range. This information is crucial for testing and developing models of hillslope evolution, giving especial consideration to the production and downslope transport of mobile regolith on the hillslopes. Here, we present the results of a systematic study aiming to document spatial patterns of mobile regolith thickness and meteoric Beryllium-10 (10Be) concentrations in the Gordon Gulch basin of the BcCZO. Gordon Gulch lies within the unglaciated portion of the Colorado Front Range and is thought to be an artifact of long-term steady state evolution. The basin is characterized by mixed bedrock-soil mantled hillslopes, with intermittent bedrock outcrops (tors) on ~10% of slopes. It is currently unclear how the hillslopes of Gordon Gulch have evolved given the variable rock type and strength (i.e., fracture spacing), gradients (steep slopes in lower basin compared to gradual in the upper), and hillslope aspects (north versus south facing hillslopes, with varying tree types and soil moisture for frost cracking and heaving) that exist within the basin. Furthermore, climate data suggest that the current climate regime (relatively warm) is representative of only 20% of the last 65 ka. Mobile regolith thickness measurements provide a snapshot of hillslope evolution in the basin given these controls, and meteoric 10Be can used to constrain residence times and trace mobile regolith transport. We measure mobile regolith thickness as the depth to immobile weathered bedrock and/or saprolite. Preliminary analysis of over 200 soil pits reveals a high degree of variability in mobile regolith thickness. In general, the mobile regolith cover is thinner on the south facing slopes than the north facing and a general thickening of mobile regolith occurs on steeper slopes, especially along

  8. A coordinated study of 1 h mesoscale gravity waves propagating from Logan to Boulder with CRRL Na Doppler lidars and temperature mapper

    Science.gov (United States)

    Lu, Xian; Chen, Cao; Huang, Wentao; Smith, John A.; Chu, Xinzhao; Yuan, Tao; Pautet, Pierre-Dominique; Taylor, Mike J.; Gong, Jie; Cullens, Chihoko Y.

    2015-10-01

    We present the first coordinated study using two lidars at two separate locations to characterize a 1 h mesoscale gravity wave event in the mesopause region. The simultaneous observations were made with the Student Training and Atmospheric Research (STAR) Na Doppler lidar at Boulder, CO, and the Utah State University Na Doppler lidar and temperature mapper at Logan, UT, on 27 November 2013. The high precision possessed by the STAR lidar enabled these waves to be detected in vertical wind. The mean wave amplitudes are ~0.44 m/s in vertical wind and ~1% in relative temperature at altitudes of 82-107 km. Those in the zonal and meridional winds are 6.1 and 5.2 m/s averaged from 84 to 99 km. The horizontal and vertical wavelengths inferred from the mapper and lidars are ~219 ± 4 and 16.0 ± 0.3 km, respectively. The intrinsic period is ~1.3 h for the airglow layer, Doppler shifted by a mean wind of ~17 m/s. The wave packet propagates from Logan to Boulder with an azimuth angle of ~135° clockwise from north and an elevation angle of ~ 3° from the horizon. The observed phase difference between the two locations can be explained by the traveling time of the 1 h wave from Logan to Boulder, which is about ~2.4 h. The wave polarization relations are examined through the simultaneous quantifications of the three wind components and temperature. This study has developed a systematic methodology for fully characterizing mesoscale gravity waves, inspecting their intrinsic properties and validating the derivation of horizontal wave structures by applying multiple instruments from coordinated stations.

  9. Lagrangian sampling of wastewater treatment plant effluent in Boulder Creek, Colorado, and Fourmile Creek, Iowa, during the summer of 2003 and spring of 2005--Hydrological and chemical data

    Science.gov (United States)

    Barber, Larry B.; Keefe, Steffanie H.; Kolpin, Dana W.; Schnoebelen, Douglas J.; Flynn, Jennifer L.; Brown, Gregory K.; Furlong, Edward T.; Glassmeyer, Susan T.; Gray, James L.; Meyer, Michael T.; Sandstrom, Mark W.; Taylor, Howard E.; Zaugg, Steven D.

    2011-01-01

    This report presents methods and data for a Lagrangian sampling investigation into chemical loading and in-stream attenuation of inorganic and organic contaminants in two wastewater treatment-plant effluent-dominated streams: Boulder Creek, Colorado, and Fourmile Creek, Iowa. Water-quality sampling was timed to coincide with low-flow conditions when dilution of the wastewater treatment-plant effluent by stream water was at a minimum. Sample-collection times corresponded to estimated travel times (based on tracer tests) to allow the same "parcel" of water to reach downstream sampling locations. The water-quality data are linked directly to stream discharge using flow- and depth-integrated composite sampling protocols. A range of chemical analyses was made for nutrients, carbon, major elements, trace elements, biological components, acidic and neutral organic wastewater compounds, antibiotic compounds, pharmaceutical compounds, steroid and steroidal-hormone compounds, and pesticide compounds. Physical measurements were made for field conditions, stream discharge, and time-of-travel studies. Two Lagrangian water samplings were conducted in each stream, one in the summer of 2003 and the other in the spring of 2005. Water samples were collected from five sites in Boulder Creek: upstream from the wastewater treatment plant, the treatment-plant effluent, and three downstream sites. Fourmile Creek had seven sampling sites: upstream from the wastewater treatment plant, the treatment-plant effluent, four downstream sites, and a tributary. At each site, stream discharge was measured, and equal width-integrated composite water samples were collected and split for subsequent chemical, physical, and biological analyses. During the summer of 2003 sampling, Boulder Creek downstream from the wastewater treatment plant consisted of 36 percent effluent, and Fourmile Creek downstream from the respective wastewater treatment plant was 81 percent effluent. During the spring of 2005

  10. Multilateral nonproliferation cooperation: US-led effort to remove HEU/LEU fresh and spent fuel from the Republic of Georgia to Dounreay, Scotland (Auburn Endeavor/Project Olympus)

    International Nuclear Information System (INIS)

    In early March 1998, the United States government approved a plan in cooperation with the United Kingdom and Georgian governments to rapidly retrieve and transport about 4.3 kilograms of enriched uranium. This material consisted largely of highly enriched uranium and a small amount of low-enriched uranium fresh fuel, as well as about 800 grams of HEU/LEU-based spent fuel from a shutdown IRT-M research reactor on the outskirts of Tbilisi in Georgia, a former Soviet republic. A technical team led by DOE consisted of HEU handling, packing and transportation experts from the Oak Ridge Y-12 Plant, managed and operated by Lockheed Martin Energy Systems, and spent fuel handling and transportation experts from NAC International in Norcross, Georgia, U.S.A. The team was part of an interagency task force formed with Department of Defense military personnel under US European Command and headed by a senior official from the Department of State. The operation was executed in full cooperation with the government of the Republic of Georgia and the staff at the institute of Physics. In April of 1998, the fresh fuel was repacked in US-supplied 6M-2R containers [USA/0002/B(U)F] and the spent fuel was repacked in the NAC-LWT cask [USA/9225/B(U)F-85]. All the containers were then transported in one US Air Force C-5B cargo aircraft via air-to-air refueling from Tbilisi, Georgia, to Kinloss Royal Air Force Base outside Inverness, Scotland. In Scotland the fresh and spent fuel was transported north to the Dounreay Nuclear Complex west of Thurso, Caithness, Scotland, for interim storage and final disposition. This successful national security project was the first time the United States teamed with a NATO partner to remove nuclear material from a site of proliferation concern

  11. 中深孔爆破大块产生的原因分析及降低大块率的技术措施%Analysis on Causes of Producing Boulder in Medium-length Hole Blasting and the Technical Measures for Redueine Boulder Yield

    Institute of Scientific and Technical Information of China (English)

    耿贵刚; 池恩安; 刘凤钱

    2011-01-01

    In medium - length hole blasting, fragment size is affected primarily not only by terrain landform, physical properties of rock,but also by borehole pattern parameters and unit explo- sive consumption. For ecumenical blasting design and working, boulder yield is very big because of the fixed borehole pattern parameters and unit explosive consumption for a certain blasting area. This paper analyzed the reasons of producing boulder, and presents technical measures to reduce boulder yield, such as dynamically adjusting borehole pattern parameters, unit explosive consumption and charge density.%在中深孔爆破工程中,影响爆破块度的主要因素既有爆破区域的地形地貌、岩石的物理特性,还有爆破孔网参数、炸药单耗的选取等,而在一般的爆破技术设计和施工中,由于针对某一爆破区域的爆破孔网参数和炸药单耗是固定的,爆破后大块率较高。分析了大块产生的原因,提出在设计和施工中动态调整爆破孔网参数、炸药单耗、装药密度以降低大块率的技术措施。

  12. Laser Hair Removal

    Science.gov (United States)

    ... rashes clinical tools newsletter | contact Share | Hair Removal, Laser A A A AFTER: Two laser hair removal treatments were performed. This picture is ... Procedure Overview With just the right type of laser or Intense Pulsed Light (IPL) technology, suitable hairs ...

  13. PROGRAMMING OFFICE REMOVALS

    CERN Multimedia

    Groupe ST-HM

    2000-01-01

    The Removals Service recommends you to plan your removals well in advance, taking into account the fact that the Transport and Handling Group’s main priority remains the dismantling of LEP and the installation of the LHC. The requests can be made by: http://st.web.cern.ch/st/hm/removal/DEMEE.HTM Thank you for your cooperation.

  14. Study of metal removal by square Wetland System with Eleocharis SP. using SR-XRF

    Energy Technology Data Exchange (ETDEWEB)

    Avelino Neto, Sebastiao; Moreira, Silvana [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Faculdade de Engenharia Civil, Arquitetura e Urbanismo]. E-mails: savneto@bol.com.br; silvana@fec.unicamp.br

    2007-07-01

    The pollution of the water resources for metals, results of different economic activities. The objective of the present study was to use the SR-TXRF technique to evaluate the performance of Wetland system cultivated with Eleocharis sp. installed at FEAGRI-UNICAMP, in the metal removal. The metals analyzed were Cr, Mn, Fe, Zn and Pb. Samples of the wastewater in the exit, Eleocharis sp. leaf and medium boulder were collected during 20 weeks consecutively. The system was operated with different outflows and hydraulic detention times (HDT) as: 600 L.day{sup -1} (HDT 2 days), 400 L.day-1 (HDT 3 days), 300 L.day{sup -1} (HDT 4 days) and 200 L.day{sup -1} (HDT 6 days). The main source of metal removal was medium boulder with efficiency varying 30.1% for Cr and 98.9% for Pb, independent of the hydraulic detention time (HDT) used. The efficiency of the wetland in the Cr removal varied between 39.6 and 98.7%, and for Mn was higher than 81.6%. For Fe the performance was higher than 70.6% and for Cu the efficiency varied between 88.4 and 99.7 %, while for Pb the variation was 67.5 to 98.4 %. The wetland system with Eleocharis sp were in agreement with CONAMA legislation concern to Fe, Cu and Zn removal and for HDT of 2, 3, 4 and 6 days (HDT), moreover for Mn was necessary 4 and 6 days (HDT) and for Cr and Pb 6 days (HDT). (author)

  15. Natural and Anthropogenic Controls on the Ecosystem Services Provided by Dissolved Organic Matter: A Case Study of the Boulder Creek Watershed

    Science.gov (United States)

    Gabor, R. S.; McKnight, D. M.

    2011-12-01

    Dissolved organic matter (DOM) performs a number of vital functions in aquatic ecosystems, playing a substantial role in carbon and nitrogen cycles and the bioavailability of metals as well as generally affecting water chemistry. Additionally, it is considered the main cause of the the formation of harmful disinfection byproducts during water treatment processes. Because DOM is vital for ecosystem functioning, but potentially problematic for some direct human uses of water, it proves a complex case study for the application of the ecosystem services framework. To add to the complexity, human behavior can affect the amount and composition of DOM in water. Increasing concentrations of DOM have been observed in many areas of Northern Europe and North America. Hypotheses which have been suggested to explain these increased concentrations include changing land use, thawing peatlands, increased nitrogen deposition, and a lessening of acid rain, a particularly interesting idea because it would be an unintended consequence of a policy designed to protect other ecosystem functions. This multi-year study investigates DOM in the Boulder Creek Watershed in Colorado to better understand seasonal cycling of DOM and the link between DOM in the river and organic matter in the catchment, which is a substantial DOM source. Fluorescence spectroscopy was used to analyze the chemical character of the DOM in an attempt to elucidate the watershed processes driving changes in DOM concentration. Because flow in Boulder Creek is partially controlled by Barker dam and reservoir, this study site provides an opportunity to investigate both natural DOM cycling and the impact of an anthropogenic influence. By better understanding DOM cycling and the ecosystem services it provides, we can better predict how DOM dynamics may shift in the future and be prepared to adjust our behavior and water treatment processes accordingly.

  16. 广西西北部地区退化土地再造林项目人为净温室气体汇清除量预估%Research on Estimation of Net Anthropogenic GHG Removals by Sinks in Project of Reforestation on Degraded Lands in Northwest Guangxi

    Institute of Scientific and Technical Information of China (English)

    童德文; 莫祝平; 杨小兰

    2011-01-01

    为了正确评估广西西北部地区退化土地再造林项目在应对气候变化中的作用,在全面收集项目区基础材料的基础上,结合大量的野外调查,估算了项目基准净温室气体汇清除量、实际净温室气体汇清除量以及泄漏,从而可较为精确地预估项目人为净温室气体汇清除量.预估结果,项目将在2008~2027年(20年)的首个计入期内产生1,405,447 t CO2 -e的tCER,年均70 272 t CO2-e.%In order to properly assess the project of Reforestation on Degraded Lands in Northwest Guan-gxi' s role in responding to climate change, this paper based on the comprehensive collection of project basic materials, combined with a great deal of field surveys to estimate project baseline net GHG removals by sinks, actual net GHG removals by sinks and leakage, so as to estimate the amount of net anthropogenic GHG removals by sinks more accurately. And this estimation in this paper is that; the project will produce 1,405,447 t CO2 - e over the first twenty-year crediting period (from 2008-2027) , average 70,272 t CO2 -e annually.

  17. Particle adhesion and removal

    CERN Document Server

    Mittal, K L

    2015-01-01

    The book provides a comprehensive and easily accessible reference source covering all important aspects of particle adhesion and removal.  The core objective is to cover both fundamental and applied aspects of particle adhesion and removal with emphasis on recent developments.  Among the topics to be covered include: 1. Fundamentals of surface forces in particle adhesion and removal.2. Mechanisms of particle adhesion and removal.3. Experimental methods (e.g. AFM, SFA,SFM,IFM, etc.) to understand  particle-particle and particle-substrate interactions.4. Mechanics of adhesion of micro- and  n

  18. Skin lesion removal-aftercare

    Science.gov (United States)

    ... aftercare; Nevi - removal aftercare; Scissor excision aftercare; Skin tag removal aftercare; Mole removal aftercare; Skin cancer removal ... to the principles of the Health on the Net Foundation (www.hon.ch). The information provided herein ...

  19. 324 Building spent fuel segments pieces and fragments removal summary report

    Energy Technology Data Exchange (ETDEWEB)

    SMITH, C L

    2003-01-09

    As part of the 324 Building Deactivation Project, all Spent Nuclear Fuel (SNF) and Special Nuclear Material were removed. The removal entailed packaging the material into a GNS-12 cask and shipping it to the Central Waste Complex (CWC).

  20. Project 2010 Project Management

    CERN Document Server

    Happy, Robert

    2010-01-01

    The ideal on-the-job reference guide for project managers who use Microsoft Project 2010. This must-have guide to using Microsoft Project 2010 is written from a real project manager's perspective and is packed with information you can use on the job. The book explores using Project 2010 during phases of project management, reveals best practices, and walks you through project flow from planning through tracking to closure. This valuable book follows the processes defined in the PMBOK Guide, Fourth Edition , and also provides exam prep for Microsoft's MCTS: Project 2010 certification.: Explains

  1. Thyroid gland removal - discharge

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/patientinstructions/000293.htm Thyroid gland removal - discharge To use the sharing features ... surgery. This will make your scar show less. Thyroid Hormone Replacement You may need to take thyroid ...

  2. Hardware removal - extremity

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/007644.htm Hardware removal - extremity To use the sharing features on this page, please enable JavaScript. Surgeons use hardware such as pins, plates, or screws to help ...

  3. Gallbladder removal - laparoscopic

    Science.gov (United States)

    ... PA: Elsevier Saunders; 2012:chap 55. Read More Acute cholecystitis Chronic cholecystitis Gallbladder removal - open Gallstones Patient Instructions Bland diet Surgical wound care - open When you have nausea and vomiting ...

  4. Reactor for removing ammonia

    Science.gov (United States)

    Luo, Weifang; Stewart, Kenneth D.

    2009-11-17

    Disclosed is a device for removing trace amounts of ammonia from a stream of gas, particularly hydrogen gas, prepared by a reformation apparatus. The apparatus is used to prevent PEM "poisoning" in a fuel cell receiving the incoming hydrogen stream.

  5. Laparoscopic Adrenal Gland Removal

    Science.gov (United States)

    ... adrenal tumors that appear malignant. What are the Advantages of Laparoscopic Adrenal Gland Removal? In the past, ... of procedure and the patients overall condition. Common advantages are: Less postoperative pain Shorter hospital stay Quicker ...

  6. Mildew remover poisoning

    Science.gov (United States)

    ... level of consciousness and lack of responsiveness) Stupor SKIN Burns Irritation Necrosis (holes) in the skin or underlying ... Fluids through a vein (IV) Surgical removal of burned skin (skin debridement) Washing of the skin (irrigation). Perhaps ...

  7. Dye remover poisoning

    Science.gov (United States)

    ... SYSTEM Collapse Low blood pressure that develops rapidly SKIN Burns Holes (necrosis) in the skin or tissues underneath ... vein) Medicines to treat pain Surgical removal of burned skin (skin debridement) Washing of the skin (irrigation), perhaps ...

  8. Random Sampling with Removal

    OpenAIRE

    Gärtner, Bernd; Lengler, Johannes; Szedlak, May

    2015-01-01

    Random sampling is a classical tool in constrained optimization. Under favorable conditions, the optimal solution subject to a small subset of randomly chosen constraints violates only a small subset of the remaining constraints. Here we study the following variant that we call random sampling with removal: suppose that after sampling the subset, we remove a fixed number of constraints from the sample, according to an arbitrary rule. Is it still true that the optimal solution of the reduced s...

  9. Laser hair removal pearls.

    Science.gov (United States)

    Tierney, Emily P; Goldberg, David J

    2008-03-01

    A number of lasers and light devices are now available for the treatment of unwanted hair. The goal of laser hair removal is to damage stem cells in the bulge of the follicle through the targeting of melanin, the endogenous chromophore for laser and light devices utilized to remove hair. The competing chromophores in the skin and hair, oxyhemoglobin and water, have a decreased absorption between 690 nm and 1000 nm, thus making this an ideal range for laser and light sources. Pearls of laser hair removal are presented in this review, focusing on four areas of recent development: 1 treatment of blond, white and gray hair; 2 paradoxical hypertrichosis; 3 laser hair removal in children; and 4 comparison of lasers and IPL. Laser and light-based technologies to remove hair represents one of the most exciting areas where discoveries by dermatologists have led to novel treatment approaches. It is likely that in the next decade, continued advancements in this field will bring us closer to the development of a more permanent and painless form of hair removal.

  10. Laser hair removal pearls.

    Science.gov (United States)

    Tierney, Emily P; Goldberg, David J

    2008-03-01

    A number of lasers and light devices are now available for the treatment of unwanted hair. The goal of laser hair removal is to damage stem cells in the bulge of the follicle through the targeting of melanin, the endogenous chromophore for laser and light devices utilized to remove hair. The competing chromophores in the skin and hair, oxyhemoglobin and water, have a decreased absorption between 690 nm and 1000 nm, thus making this an ideal range for laser and light sources. Pearls of laser hair removal are presented in this review, focusing on four areas of recent development: 1 treatment of blond, white and gray hair; 2 paradoxical hypertrichosis; 3 laser hair removal in children; and 4 comparison of lasers and IPL. Laser and light-based technologies to remove hair represents one of the most exciting areas where discoveries by dermatologists have led to novel treatment approaches. It is likely that in the next decade, continued advancements in this field will bring us closer to the development of a more permanent and painless form of hair removal. PMID:18330794

  11. Discussion on Construction Measures in Small-sized Reservoir Risk Removal Reinforcement Project%小型水库除险加固工程施工措施探讨

    Institute of Scientific and Technical Information of China (English)

    许文锋; 周勇; 徐莉美

    2014-01-01

    Existing problems in Zhejiang Ningbo small-sized reservoir risk removal reinforcement construction are analyzed in the paper .Some effective coping strategies are proposed on the basis as reference .%本文对当前浙江省宁波市小型水库除险加固施工中存在着的问题进行分析,并在此基础上提出一些有效的应对策略,以供参考。

  12. Position paper -- Waste storage tank heat removal

    International Nuclear Information System (INIS)

    The purpose of this paper is to develop and document a position on the heat removal system to be used on the waste storage tanks currently being designed for the Multi-Function Waste Tank Facility (MWTF), project W-236A. The current preliminary design for the waste storage primary tank heat removal system consists of the following subsystems: (1) a once-through dome space ventilation system; (2) a recirculation dome space ventilation system; and (3) an annulus ventilation system. Recently completed and ongoing studies have evaluated alternative heat removal systems in an attempt to reduce system costs and to optimize heat removal capabilities. In addition, a thermal/heat transfer analysis is being performed that will provide assurance that the heat removal systems selected will be capable of removing the total primary tank design heat load of 1.25 MBtu/hr at an allowable operating temperature of 190 F. Although 200 F is the design temperature limit, 190 F has been selected as the maximum allowable operating temperature limit based on instrumentation sensitivity, instrumentation location sensitivity, and other factors. Seven options are discussed and recommendations are made

  13. Changes in population structure and body dimensions of two xanthid crabs: A long-term study in a single boulder-shore

    Directory of Open Access Journals (Sweden)

    M.R. Warburg

    2012-06-01

    Full Text Available Two xanthid crab species were studied during 29 months over a period of 14 years between 1986 and 1999 all in exactly the same boulder shore. One of the crab species studied was the xanthid, Eriphia verrucosa (Forskall, 1775 with 60 specimens, the other species, Xantho poressa (Olivi, 1792, with 155 specimens. A significant change in numbers of both males and females of E. verrucosa was noticeable between 1986 and 1996 with a marked drop in numbers between these years. In 1997 male numbers increased again to almosttheir previous numbers in the population during 1986. The population of X. poressa declined significantly towards the end of the study period. Numbers of both genders peaked in spring and again, in summer. There was generally a decline in numbers of both crab species during autumn and winter. Thus, the average capture during the seasons was highest in spring for males of both E. verrucosa, and X. poressa. The body dimensions: mass, carapace length (CL and width (CW were measured in both xanthids. The aim of this long-term study was to determine whether temporal changes in the population structure and allometric changes in the dimensions of these crabs took place. Only such long-term observations could reveal these changes in population.

  14. Incorporation of island-arc rocks into a Caribbean subduction channel: Geochemical constraints from eclogite boulders and greenschist rocks, Guajira region, Colombia

    Science.gov (United States)

    Weber, M.; Cardona, A.; Altenberger, U.; Garcia-Casco, A.; Valencia, V.; Tobón, M.; Zapata, S.

    2009-12-01

    Characterization of the protoliths of a subduction-accretion complex can provide major insights into the dynamics of the subduction channel. Geochemistry of eclogites found as boulders in a Tertiary conglomerate from the Guajira Peninsula, Colombia, indicate that these rocks are mainly metamorphosed basalts. A negative Nb-anomaly and flat to enriched REE patterns suggest that the eclogite protoliths evolved in a subduction related tectonic setting, with island arc affinities. The geochemical characteristics are similar to low-grade greenschists from the nearby Etpana Formation, which is interpreted as part of a Cretaceous intra-oceanic arc. This further supports evidence that the deposition and metamorphism of these units record the ongoing Late Cretaceous continental subduction of the South American margin beneath the advancing Caribbean arc. This gave way to an arc-continent collision between the Caribbean and the South American plates. Arc-rocks were incorporated into the subduction channel and the accretionary wedge, either though influx of tectonically eroded arc material (subduction erosion) or incorporation into the accretionary wedge during arc-continent collision.

  15. Sedimentology of granite boulder conglomerates and associated clastics in the onshore section of the late Mesozoic Pletmos Basin (Western Cape, South Africa)

    Science.gov (United States)

    Bordy, Emese M.; America, Travis

    2016-07-01

    Along the southern margin of South Africa, intermountain rift successions, which comprise unusually large, rounded granite boulders and other coarse clastics, reveal an important geological history about the mid-Mesozoic extensional tectonics that lead to the break-up of Gondwana. These strata, mapped as part of the Mid to Upper Jurassic Enon Formation, allow the assessment of the nature, intensity and mode of sediment transport in onshore section of the Pletmos Basin, which is one of the late Mesozoic basins in southern Africa. Based on sedimentary facies analysis, palaeocurrent measurements and semi-quantitative palaeohydraulic calculations, the results suggest that the abundant coarse sediment was deposited by debris-flows and stream-flow floods on a proximal alluvial fan with high gradient alluvial channels. The floods were intense with mean flow velocity of ∼6 m3/s and peak discharge of ∼450 m3/s. While the role of climate in the sedimentation dynamics remains unknown, syn-sedimentary rift tectonics were likely significant and caused, north of the major boundary fault, the unroofing and denudation of the uplifted mountainous source areas, including the Late Ediacaran-Cambrian Maalgaten Granite Suite and the Siluro-Ordovician Table Mountain Group (Cape Supergroup).

  16. One piece reactor removal

    International Nuclear Information System (INIS)

    Japan Research Reactor No.3 (JRR-3) was the first reactor consisting of 'Japanese-made' components alone except for fuel and heavy water. After reaching its initial critical state in September 1962, JRR-3 had been in operation for 21 years until March 1983. It was decided that the reactor be removed en-bloc in view of the work schedule, cost and management of the reactor following the removal. In the special method developed jointly by the Japanese Atomic Energy Research Institute and Shimizu Construction Co., Ltd., the reactor main unit was cut off from the building by continuous core boring, with its major components bound in the block with biological shield material (heavy concrete), and then conveyed and stored in a large waste store building constructed near the reactor building. Major work processes described in this report include the cutting off, lifting, horizontal conveyance and lowering of the reactor main unit. The removal of the JRR-3 reactor main unit was successfully carried out safely and quickly by the en-block removal method with radiation exposure dose of the workers being kept at a minimum. Thus the high performance of the en-bloc removal method was demonstrated and, in addition, valuable knowhow and other data were obtained from the work. (Nogami, K.)

  17. Arsenic removal from water

    Science.gov (United States)

    Moore, Robert C.; Anderson, D. Richard

    2007-07-24

    Methods for removing arsenic from water by addition of inexpensive and commonly available magnesium oxide, magnesium hydroxide, calcium oxide, or calcium hydroxide to the water. The hydroxide has a strong chemical affinity for arsenic and rapidly adsorbs arsenic, even in the presence of carbonate in the water. Simple and commercially available mechanical methods for removal of magnesium hydroxide particles with adsorbed arsenic from drinking water can be used, including filtration, dissolved air flotation, vortex separation, or centrifugal separation. A method for continuous removal of arsenic from water is provided. Also provided is a method for concentrating arsenic in a water sample to facilitate quantification of arsenic, by means of magnesium or calcium hydroxide adsorption.

  18. Plate removal following orthognathic surgery.

    Science.gov (United States)

    Little, Mhairi; Langford, Richard Julian; Bhanji, Adam; Farr, David

    2015-11-01

    The objectives of this study are to determine the removal rates of orthognathic plates used during orthognathic surgery at James Cook University Hospital and describe the reasons for plate removal. 202 consecutive orthognathic cases were identified between July 2004 and July 2012. Demographics and procedure details were collected for these patients. Patients from this group who returned to theatre for plate removal between July 2004 and November 2012 were identified and their notes were analysed for data including reason for plate removal, age, smoking status, sex and time to plate removal. 3.2% of plates were removed with proportionally more plates removed from the mandible than the maxilla. 10.4% of patients required removal of one or more plate. Most plates were removed within the first post-operative year. The commonest reasons for plate removal were plate exposure and infection. The plate removal rates in our study are comparable to those seen in the literature.

  19. A close-up of the ALEPH Time Projection Chamber (TPC) after the detector was dismantled, with a slice removed for the exhibition at the Musée International d'Horlogerie.

    CERN Multimedia

    2004-01-01

    On the occasion of CERN's 50th anniversary, starting 2 December at the Musée International d'Horlogerie in La Chaux-de-Fonds, Switzerland, a new exhibition will pay tribute to physics, from the cosmic to the subatomic scales. The exhibition, which run for several years, includes a slice of the Time Projection Chamber (TPC) from ALEPH, one of the LEP detectors, which CERN donated to the museum when the detector was dismantled.

  20. Removing Welding Fumes

    Science.gov (United States)

    Moore, Lloyd J.; Hall, Vandel L.

    1987-01-01

    Portable exhaust duct for machining and welding shops removes oil mist, dust, smoke, and fumes. Duct used with shop exhaust system, inlets of which placed at various convenient locations in shop floor. Flanged connector on underside of wheeled base links flexible tube to exhaust system under floor. Made especially for welding in room with low ceiling.

  1. The evolution of gravel bed channels after dam removal: Case study of the Anaconda and Union City Dam removals

    Science.gov (United States)

    Wildman, Laura A. S.; MacBroom, James G.

    2005-10-01

    The Anaconda and Union City Dams on the Naugatuck River in Connecticut were removed in February and October 1999. A detailed study of the sites prior to removal was undertaken including sediment testing and predictions of upstream channel formation post-dam removal. The 3.35-m-high timber crib/rock fill spillway of the Anaconda Dam partially breached during a storm prior to the dam's scheduled removal allowing a portion of the impounded sediment to move down through the river system. This event changed the removal plans and the remainder of the spillway was removed under an emergency order in the course of 4 days. The Union City Dam, a 2.44-m-high timber crib/rock fill dam capped with concrete and stone, was removed on schedule. A portion of the impounded sediment was removed by mechanical means during the deconstruction of the structure. The evolution of the two upstream channels post-project provided unique challenges and valuable insights as to what kind of channel transition can be expected in gravel bed river systems after a low head dam has been removed. This paper describes the initial engineering analysis and design, the subsequent removal of the two dams, and compares observations on the transition of the upstream channels following dam removal to the initial engineering predictions and other models. The relatively steep gravel bed channels evolved in a predictable manner, except where anthropogenic barriers (sanitary sewer, rock weir) interrupted.

  2. Hillslope lowering rates and mobile-regolith residence times from in situ and meteoric 10Be analysis: Boulder Creek Critical Zone Observatory, Colorado

    Science.gov (United States)

    Foster, M. A.; Anderson, R. S.; Wyshnytzky, C.; Ouimet, W. B.; Dethier, D. P.

    2014-12-01

    Mobile regolith is produced as weathered saprolite is entrained into the mobile layer. The rate of mobile-regolith production and its residence time on hillslopes shapes the topography and evolution of hillslopes. We calculate the production rate of mobile regolith and the mobile-regolith residence times on active hillslopes in Gordon Gulch, within the Boulder Creek Critical Zone Observatory (CZO), Colorado. We find mobile-regolith production rates (average 3.1 cm/ka) and residence times (average 10-20 ka) derived from both in situand meteoric methods agree. Lowering-rates derived from our study are also comparable to basin-averaged denudation rates for small basins in the Colorado Front Range (Dethier and Lazarus, 2006). In this study, we have measured both in situ and meteoric 10Be in saprolite and mobile regolith separately. We find that, on average, two-thirds of in situ 10Be is produced within saprolite, and that at least one-tenth of the meteoric 10Be inventories are stored in saprolite. In the case of in situ 10Be, this simply reflects the exponential fall-off in production rates through a thin mobile-regolith cover. In the case of meteoric 10Be, our calculations suggest that >40% of the meteoric 10Be deposition occurs within the saprolite. Most studies that utilize 10Be report residence times and soil-production rates based on concentrations in either the mobile regolith or saprolite; therefore, our 10Be data highlight the importance of clearly identifying mobile and immobile portions of the regolith, constraining its 10Be inventory, and use of consistent terminology for the mobile-layer.

  3. An adaptive strategy for active debris removal

    Science.gov (United States)

    White, Adam E.; Lewis, Hugh G.

    2014-04-01

    Many parameters influence the evolution of the near-Earth debris population, including launch, solar, explosion and mitigation activities, as well as other future uncertainties such as advances in space technology or changes in social and economic drivers that effect the utilisation of space activities. These factors lead to uncertainty in the long-term debris population. This uncertainty makes it difficult to identify potential remediation strategies, involving active debris removal (ADR), that will perform effectively in all possible future cases. Strategies that cannot perform effectively, because of this uncertainty, risk either not achieving their intended purpose, or becoming a hindrance to the efforts of spacecraft manufactures and operators to address the challenges posed by space debris. One method to tackle this uncertainty is to create a strategy that can adapt and respond to the space debris population. This work explores the concept of an adaptive strategy, in terms of the number of objects required to be removed by ADR, to prevent the low Earth orbit (LEO) debris population from growing in size. This was demonstrated by utilising the University of Southampton’s Debris Analysis and Monitoring Architecture to the Geosynchronous Environment (DAMAGE) tool to investigate ADR rates (number of removals per year) that change over time in response to the current space environment, with the requirement of achieving zero growth of the LEO population. DAMAGE was used to generate multiple Monte Carlo projections of the future LEO debris environment. Within each future projection, the debris removal rate was derived at five-year intervals, by a new statistical debris evolutionary model called the Computational Adaptive Strategy to Control Accurately the Debris Environment (CASCADE) model. CASCADE predicted the long-term evolution of the current DAMAGE population with a variety of different ADR rates in order to identify a removal rate that produced a zero net

  4. Investigations in gallium removal

    Energy Technology Data Exchange (ETDEWEB)

    Philip, C.V.; Pitt, W.W. [Texas A and M Univ., College Station, TX (United States); Beard, C.A. [Amarillo National Resource Center for Plutonium, TX (United States)

    1997-11-01

    Gallium present in weapons plutonium must be removed before it can be used for the production of mixed-oxide (MOX) nuclear reactor fuel. The main goal of the preliminary studies conducted at Texas A and M University was to assist in the development of a thermal process to remove gallium from a gallium oxide/plutonium oxide matrix. This effort is being conducted in close consultation with the Los Alamos National Laboratory (LANL) personnel involved in the development of this process for the US Department of Energy (DOE). Simple experiments were performed on gallium oxide, and cerium-oxide/gallium-oxide mixtures, heated to temperatures ranging from 700--900 C in a reducing environment, and a method for collecting the gallium vapors under these conditions was demonstrated.

  5. Facilities removal working group

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This working group`s first objective is to identify major economic, technical, and regulatory constraints on operator practices and decisions relevant to offshore facilities removal. Then, the group will try to make recommendations as to regulatory and policy adjustments, additional research, or process improvements and/or technological advances, that may be needed to improve the efficiency and effectiveness of the removal process. The working group will focus primarily on issues dealing with Gulf of Mexico platform abandonments. In order to make the working group sessions as productive as possible, the Facilities Removal Working Group will focus on three topics that address a majority of the concerns and/or constraints relevant to facilities removal. The three areas are: (1) Explosive Severing and its Impact on Marine Life, (2) Pile and Conductor Severing, and (3) Deep Water Abandonments This paper will outline the current state of practice in the offshore industry, identifying current regulations and specific issues encountered when addressing each of the three main topics above. The intent of the paper is to highlight potential issues for panel discussion, not to provide a detailed review of all data relevant to the topic. Before each panel discussion, key speakers will review data and information to facilitate development and discussion of the main issues of each topic. Please refer to the attached agenda for the workshop format, key speakers, presentation topics, and panel participants. The goal of the panel discussions is to identify key issues for each of the three topics above. The working group will also make recommendations on how to proceed on these key issues.

  6. KKG Group Paraffin Removal

    Energy Technology Data Exchange (ETDEWEB)

    Schulte, Ralph

    2001-12-01

    The Rocky Mountain Oilfield Testing Center (RMOTC) has recently completed a test of a paraffin removal system developed by the KKG Group utilizing the technology of two Russian scientists, Gennady Katzyn and Boris Koggi. The system consisting of chemical ''sticks'' that generate heat in-situ to melt the paraffin deposits in oilfield tubing. The melted paraffin is then brought to the surface utilizing the naturally flowing energy of the well.

  7. Laser removal of tattoos.

    Science.gov (United States)

    Tammaro, A; Fatuzzo, G; Narcisi, A; Abruzzese, C; Caperchi, C; Gamba, A; Parisella, F R; Persechino, S

    2012-01-01

    In Western countries the phenomenon of "tattooing" is expanding and tattoos are considered a new fashion among young people. In this paper we briefly trace the history of tattooing, the techniques used, the analysis of pigments used, and their possible adverse reactions. We also carried out a review of the international literature on the use of Q-switched laser in tattoo removal and its complications, and we describe our experience in the use of this technique. PMID:22697088

  8. Power plant removal costs

    International Nuclear Information System (INIS)

    The financial, regulatory and political significance of the estimated high removal costs of nuclear power plants has generated considerable interest in recent years, and the political significance has resulted in the Nuclear Regulatory Commission (NRC) eliminating the use of conventional depreciation accounting for the decontamination portion of the removal (decommissioning). While nuclear plant licensees are not precluded from utilizing conventional depreciation accounting for the demolition of non-radioactive structures and site restoration, state and federal utility regulators have not been favorably inclined to requests for this distinction. The realization that steam-generating units will be more expensive to remove, relative to their original cost, predates the realization that nuclear units will be expensive. However, the nuclear issues have overshadowed this realization, but are unlikely to continue to do so. Numerous utilities have prepared cost estimates for steam generating units, and this presentation discusses the implications of a number of such estimates that are a matter of public record. The estimates cover nearly 400 gas, oil, coal and lignite generating units. The earliest estimate was made in 1978, and for analysis purposes the author has segregated them between gas and oil units, and coal and lignite units

  9. Nitrogen removal from natural gas

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-04-01

    According to a 1991 Energy Information Administration estimate, U.S. reserves of natural gas are about 165 trillion cubic feet (TCF). To meet the long-term demand for natural gas, new gas fields from these reserves will have to be developed. Gas Research Institute studies reveal that 14% (or about 19 TCF) of known reserves in the United States are subquality due to high nitrogen content. Nitrogen-contaminated natural gas has a low Btu value and must be upgraded by removing the nitrogen. In response to the problem, the Department of Energy is seeking innovative, efficient nitrogen-removal methods. Membrane processes have been considered for natural gas denitrogenation. The challenge, not yet overcome, is to develop membranes with the required nitrogen/methane separation characteristics. Our calculations show that a methane-permeable membrane with a methane/nitrogen selectivity of 4 to 6 would make denitrogenation by a membrane process viable. The objective of Phase I of this project was to show that membranes with this target selectivity can be developed, and that the economics of the process based on these membranes would be competitive. Gas permeation measurements with membranes prepared from two rubbery polymers and a superglassy polymer showed that two of these materials had the target selectivity of 4 to 6 when operated at temperatures below - 20{degrees}C. An economic analysis showed that a process based on these membranes is competitive with other technologies for small streams containing less than 10% nitrogen. Hybrid designs combining membranes with other technologies are suitable for high-flow, higher-nitrogen-content streams.

  10. Melter Glass Removal and Dismantlement

    Energy Technology Data Exchange (ETDEWEB)

    Richardson, BS

    2000-10-31

    The U.S. Department of Energy (DOE) has been using vitrification processes to convert high-level radioactive waste forms into a stable glass for disposal in waste repositories. Vitrification facilities at the Savannah River Site (SRS) and at the West Valley Demonstration Project (WVDP) are converting liquid high-level waste (HLW) by combining it with a glass-forming media to form a borosilicate glass, which will ensure safe long-term storage. Large, slurry fed melters, which are used for this process, were anticipated to have a finite life (on the order of two to three years) at which time they would have to be replaced using remote methods because of the high radiation fields. In actuality the melters useable life spans have, to date, exceeded original life-span estimates. Initial plans called for the removal of failed melters by placing the melter assembly into a container and storing the assembly in a concrete vault on the vitrification plant site pending size-reduction, segregation, containerization, and shipment to appropriate storage facilities. Separate facilities for the processing of the failed melters currently do not exist. Options for handling these melters include (1) locating a facility to conduct the size-reduction, characterization, and containerization as originally planned; (2) long-term storing or disposing of the complete melter assembly; and (3) attempting to refurbish the melter and to reuse the melter assembly. The focus of this report is to look at methods and issues pertinent to size-reduction and/or melter refurbishment in particular, removing the glass as a part of a refurbishment or to reduce contamination levels (thus allowing for disposal of a greater proportion of the melter as low level waste).

  11. InTouch组态软件在伊敏某电厂除灰渣工程中的应用%Application of InTouch configuration softwareduring the removing ash & slag project at the power plant in Yimin

    Institute of Scientific and Technical Information of China (English)

    李万军

    2012-01-01

    针对伊敏某电厂除灰渣工程,采用人机界面组态软件InTouch9.0进行监控系统设计.介绍了上位机控制系统的硬件配置,采用面向对象思想开发了完整的工程监控画面,实现了除灰渣工程的实时监控和生产运行情况的实时动态显示,自动报警和在流程图画面上实施对现场设备的控制操作.使用的结果表明,该系统操作简便、可靠,提高了电厂除灰渣的控制效率.%According to the ash project at the power plant in Yimin, the monitoring system has been designed taking the man-machine interface configuration software InTouch9. 0 as development environment. The upper machine control system hardware configuration was been introduced, a complete monitoring picture of project was been developed using the object-oriented thinking, which has achieved a realtime monitoring and real-time dynamic display of production, automatic alarm and control operations of some field devices on the screen. The result shows that the system has featured with reliable performance and ease operation, and improved the ash & slag control efficiency of the power plant.

  12. Save the Boulders Beach Penguins

    Science.gov (United States)

    Sheerer, Katherine; Schnittka, Christine

    2012-01-01

    Maybe it's the peculiar way they walk or their cute little suits, but students of all ages are drawn to penguins. To meet younger students' curiosity, the authors adapted a middle-school level, penguin-themed curriculum unit called Save the Penguins (Schnittka, Bell, and Richards 2010) for third-grade students. The students loved learning about…

  13. Iraq spent fuel removal program

    International Nuclear Information System (INIS)

    The paper describes the preparation and operations associated with the removal of the 208 spent fuel assemblies from Iraq, with emphasis on the technical challenges that were overcome during this removal process. (author)

  14. Concentrations of metals in water, sediment, biofilm, benthic macroinvertebrates, and fish in the boulder river watershed, Montana, and the role of colloids in metal uptake

    Science.gov (United States)

    Farag, A.M.; Nimick, D.A.; Kimball, B.A.; Church, S.E.; Harper, D.D.; Brumbaugh, W.G.

    2007-01-01

    To characterize the partitioning of metals in a stream ecosystem, concentrations of trace metals including As, Cd, Cu, Pb, and Zn were measured in water, colloids, sediment, biofilm (also referred to as aufwuchs), macroinvertebrates, and fish collected from the Boulder River watershed, Montana. Median concentrations of Cd, Cu, and Zn in water throughout the watershed exceeded the U.S. EPA acute and chronic criteria for protection of aquatic life. Concentrations of As, Cd, Cu, Pb, and Zn in sediment were sufficient in the tributaries to cause invertebrate toxicity. The concentrations of As, Cu, Cd, Pb, and Zn in invertebrates from lower Cataract Creek (63, 339, 59, 34, and 2,410 ??g/g dry wt, respectively) were greater than the concentrations in invertebrates from the Clark Fork River watershed, Montana (19, 174, 2.3, 15, and 648 ??g/g, respectively), that were associated with reduced survival, growth, and health of cutthroat trout fed diets composed of those invertebrates. Colloids and biofilm seem to play a critical role in the pathway of metals into the food chain and concentrations of As, Cu, Pb, and Zn in these two components are significantly correlated. We suggest that transfer of metals associated with Fe colloids to biological components of biofilm is an important pathway where metals associated with abiotic components are first available to biotic components. The significant correlations suggest that Cd, Cu, and Zn may move independently to biota (biofilm, invertebrates, or fish tissues) from water and sediment. The possibility exists that Cd, Cu, and Zn concentrations increase in fish tissues as a result of direct contact with water and sediment and indirect exposure through the food chain. However, uptake through the food chain to fish may be more important for As. Although As concentrations in colloids and biofilm were significantly correlated with As water concentrations, As concentrations in fish tissues were not correlated with water. The pathway for

  15. 浊度去除率在城市污水处理工程调试中的应用实践%Application of Turbidity Removal Ratio in Commissioning Works of Urban Sewage Treatment Projects

    Institute of Scientific and Technical Information of China (English)

    公明; 蒋孟龙; 庞艳; 冀强; 冀贞泉; 任京霞

    2011-01-01

    An urban sewage treatment plant which adopts hydrolyze acidification +BAF as the major sewage treatment technology has a treatment capaeity of 5000 m3/d and its inflow quality are COD ≤ 500 mg/l, BOD5 ≤220mg/l, SS ≤ 350 mg/l, NH3-N ≤ 15 mg/l, TN≤35 mg/l, TP≤4.0 mg/l. The effluent reached Level One A (GB18918-2002) i.e. COD≤50 mg/l, BOD≤ 10mg/l, SS ≤ 10 mg/l, flora and fauna≤ 1 mg/l, petroleum≤ 1 mg/l, NH3-N≤5 mg/l, TN≤ 15 mg/l. Adopting water cycle control method during the commissioning process, the COD was calculated by turbidity value so as to guide the system testing. According to the relation between water turbidity and COD, the turbidity removal ration was determined as a major technic control parameter. The advantage of this method includes easy operation, straightforward, adaptable to technology changes, guarantee testing effects, find abnormalities promptly and quick handling. It has a promising application prospect.%某城镇污水处理厂采用水解酸化+BAF为主要工艺处理污水,处理量0.57Ym。/d,进水水质COD≤500mg/1、BOD5≤220mg/1、SS≤350mg/1、NH3一N≤15mg/1、总氮≤35mg/1、总磷≤4.0mg/1。出水标准(GB18918≤2002)一级A标准,即COD≤50mg/1、BOD10rag/1、SS≤10mg/1、动植物≤1mg/1、石油类≤1mg/1、NH3-N≤5mg/1、总氮≤15mg/1。调试过程中采用控水周期法,同时应用浊度快速核算COD值,指导调试运行,根据水质的浊度与c0D之间的关系,确定以浊度去除率作为主要工艺控制参数,具有操作方便、直观、及时变换工艺条件,保证调试的效果,及时发现异常,快速处理,具有良好的使用前景。

  16. Removal of Engineered Nanomaterials Through Conventional Water Treatment Processes

    OpenAIRE

    Honda, Ryan

    2014-01-01

    The overall aim of this PhD research was to identify mechanisms involved in the removal of nanomaterials in conventional water treatment. This project was developed based upon the need for assessing current water treatment infrastructure, and its capacity of effectiveness in removing nanomaterials. The bulk of this dissertation investigated "primary treatment" steps of coagulation, flocculation, and sedimentation, simulated by full-scale and micro-scale jar tests. The remainder of the diss...

  17. Mercury removal sorbents

    Energy Technology Data Exchange (ETDEWEB)

    Alptekin, Gokhan

    2016-03-29

    Sorbents and methods of using them for removing mercury from flue gases over a wide range of temperatures are disclosed. Sorbent materials of this invention comprise oxy- or hydroxyl-halogen (chlorides and bromides) of manganese, copper and calcium as the active phase for Hg.sup.0 oxidation, and are dispersed on a high surface porous supports. In addition to the powder activated carbons (PACs), this support material can be comprised of commercial ceramic supports such as silica (SiO.sub.2), alumina (Al.sub.2O.sub.3), zeolites and clays. The support material may also comprise of oxides of various metals such as iron, manganese, and calcium. The non-carbon sorbents of the invention can be easily injected into the flue gas and recovered in the Particulate Control Device (PCD) along with the fly ash without altering the properties of the by-product fly ash enabling its use as a cement additive. Sorbent materials of this invention effectively remove both elemental and oxidized forms of mercury from flue gases and can be used at elevated temperatures. The sorbent combines an oxidation catalyst and a sorbent in the same particle to both oxidize the mercury and then immobilize it.

  18. Tunnel boring machine collision with an ancient boulder beach during the excavation of the Barcelona city subway L10 line: a case of adverse geology and resulting engineering solutions

    OpenAIRE

    Filbà, Marta; Salvany Duran, Josep Maria; Jubany, Jordi; Carrasco, Laura

    2016-01-01

    The existence of a layer of hard boulders up to 1 m in size within the soft sediments of the Holocene Llobregat delta in the SW of Barcelona city caused the damage and stoppage of the EPB-type tunnel boring machine that excavated the subway L10 line. This layer constitutes a detrital deposit of exceptionally large grain size developed in the base of the delta. It originated as an alluvial fan in the northern margin of the delta during the last fall of the Mediterranean Sea level, at the end o...

  19. Microbial risk and removal--a utility perspective.

    Science.gov (United States)

    Stanger, M; Agutter, P A; Lake, R C; Ashbolt, N J; Roser, D J

    2006-01-01

    In this paper the results of a sampling programme, undertaken as part of the EU MicroRisk project, are described. This project was undertaken to ascertain the occurrence of pathogens and indicators in the River Thames and their subsequent removal through a treatment works. Appropriate physico-chemical surrogates, as determined by statistical correlation are proposed for the microorganisms identified in the raw water. This study shows that under normal raw water conditions the treatment works is able to remove microbial contamination with a significant margin of safety.

  20. Ingrown toenail removal.

    Science.gov (United States)

    Zuber, Thomas J

    2002-06-15

    Ingrown toenail is a common problem resulting from various etiologies including improperly trimmed nails, hyperhidrosis, and poorly fitting shoes. Patients commonly present with pain in the affected nail but with progression, drainage, infection, and difficulty walking occur. Excision of the lateral nail plate combined with lateral matricectomy is thought to provide the best chance for eradication. The lateral aspect of the nail plate is removed with preservation of the remaining healthy nail plate. Electrocautery ablation is then used to destroy the exposed nail-forming matrix, creating a new lateral nail fold. Complications of the procedure include regrowth of a nail spicule secondary to incomplete matricectomy and postoperative nail bed infection. When performed correctly, the procedure produces the greatest success in the treatment of ingrown nails. Basic soft tissue surgery and electrosurgery experience are prerequisites for learning the technique. PMID:12086244

  1. Cut-off wall construction at the Peribonka hydroelectric project

    Energy Technology Data Exchange (ETDEWEB)

    Ouellette, C.; Morency, J.Y.; Bigras, A.; Hammamji, Y. [Hydro-Quebec Equipment, Montreal, PQ (Canada); Gagne, B. [SNC-Lavalin, Montreal, PQ (Canada); Rattue, A. [SNC-Lavalin, Montreal, PQ (Canada). Energy Division

    2007-07-01

    The Peribonka hydroelectric development, located in Quebec includes a 80 metre high dam and two dikes consisting of zoned earth and rock fills with a till core, an underground power house, a diversion tunnel and a spillway. The project is in its final stages of construction and presented several challenges related to the presence of a deep canyon under the river bed filled with alluvial sand, gravel, cobbles and boulders. The design included an approximately 10 metre high working platform in the river and the construction of a plastic concrete cut-off wall down to bedrock. The construction of a 116 metre deep single cut-off wall that is at the limit of precedent in terms of present knowledge and equipment capacity was the main challenge for the project. In addition, a 52 metre deep plastic concrete cut-off wall was built under a dyke. This conference discussed the cut-off wall construction experience, as well as the challenges encountered and how they were addressed. The paper presented a description of the site conditions and the scope of the work, as well as the typical specifications of the cut-offs. The paper also provided an overview of an extensive quality control program that was implemented for all phases of the project construction and results of the project. Last, the paper described the challenges, problems encountered and the modifications from the initial design and specifications. It was concluded that the topography at the Peribonka dam site showed a deep narrow gully filled with alluvial material comprising sand, gravel, cobbles and boulders. Elaborate quality control was essential to ensure that excavation and concreting were done to satisfactory standards. 4 refs., 4 tabs., 11 figs.

  2. 基于n元词组表示的去噪方法及其在跨语言映射中的应用%Noise removing based on n-gram representations and its applications to cross-lingual projection

    Institute of Scientific and Technical Information of China (English)

    于墨; 赵铁军

    2016-01-01

    Problems with structured predictions ( structured learning) widely exist in natural language processing. Recent research found that compared to classification problems, structured learning problems were affected more seriously by label noises, suggesting the importance of noise removing algorithms for these problems. Inspired by the development of representation learning methods, the paper proposes a noise⁃removing algorithm for structured learning based on low⁃dimensional representations of sub⁃structures. The algorithm finds neighbors of each node in a sequential labeling task based on its associated n⁃gram representation, and then performs noise removing on the label of a node according to its consistency with the labels of its neighbors. Therefore the paper proves the effectiveness of the proposed algorithm on the cross⁃lingual projection of named entity recognition and POS tagging tasks.%具有结构化输出的学习任务(结构化学习)在自然语言处理领域广泛存在。近年来研究人员们从理论上证明了数据标记的噪声对于结构化学习的巨大影响,因此为适应结构化学习任务的去噪算法提出了需求。受到近年来表示学习发展的启发,本文提出将自然语言的子结构低维表示引入结构化学习任务的样本去噪算法中。这一新的去噪算法通过n元词组的表示为序列标注问题中每个节点寻找近邻,并根据节点标记与其近邻标记的一致性实现去噪。本文在命名实体识别和词性标注任务的跨语言映射上对上述去噪方法进行了验证,证明了这一方法的有效性。

  3. Neoarchean orogenic, magmatic and hydrothermal events in the Kalgoorlie-Kambalda area, Western Australia: constraints on gold mineralization in the Boulder Lefroy-Golden Mile fault system

    Science.gov (United States)

    Mueller, Andreas G.; Hagemann, Steffen G.; McNaughton, Neal J.

    2016-08-01

    The Boulder Lefroy-Golden Mile (BLF-GMF) fault system is the most intensely mineralized structure (>2150 t Au to 2015) in the Archean Yilgarn Craton, Western Australia. The fault system links the Kalgoorlie and Kambalda mining districts in the Eastern Goldfields Province, a continental-margin orogen subdivided into the western Kalgoorlie ensialic rift and the eastern Kurnalpi volcanic arc. After rifting, the 2.73-2.66 Ga greenstone-greywacke succession in the Kalgoorlie-Kambalda area underwent five phases of orogenic deformation, predominantly during ENE-WSW shortening: D1 upright folding at ca. 2680 Ma, D2 sinistral strike-slip faulting at 2678-2663 Ma, D3 folding of late conglomerate-turbidite successions at 2665-2655 Ma, D4 dextral strike-slip faulting at 2655-2640 Ma and D5 east-northeast-striking normal faulting. Regional prehnite-pumpellyite to greenschist facies burial metamorphism took place during D1 and D3 crustal thickening, and amphibolite facies aureoles formed around granite batholiths during and after D3 at 400 ± 100 MPa pressure. The D2 BLF offsets D1 folds by 12 km SW-side south and contains a porphyry dyke (2676 ± 7 Ma) boudinaged by transtensional oblique-slip along a line pitching 21° southeast. The BLF is linked by transverse D2 thrusts to other sinistral faults recording strike-slip until 2663 ± 7 Ma. Late D2 strike-slip movement alternated with early D3 shortening. D3 thrusts accommodated strain in fault blocks of rigid mafic-ultramafic volcanic rocks consolidated during D1, while the sedimentary rocks in D3 synclines were foliated at high strain. Biotite-sericite alteration and gold-pyrite mineralization in the BLF-GMF system took place at 11 ± 4 km burial depth in faults active during D2 and D3. The Golden Mile (1708 t Au) and other deposits are associated with stocks and dykes of high-Mg monzodiorite-tonalite porphyry, part of a late-orogenic (2665-2645 Ma) mantle-derived suite of adakitic affinity. Hornblende and apatite compositions

  4. Impacts from Partial Removal of Decommissioned Oil and Gas Platforms on Fish Biomass and Production on the Remaining Platform Structure and Surrounding Shell Mounds.

    Directory of Open Access Journals (Sweden)

    Jeremy T Claisse

    Full Text Available When oil and gas platforms become obsolete they go through a decommissioning process. This may include partial removal (from the surface to 26 m depth or complete removal of the platform structure. While complete removal would likely eliminate most of the existing fish biomass and associated secondary production, we find that the potential impacts of partial removal would likely be limited on all but one platform off the coast of California. On average 80% of fish biomass and 86% of secondary fish production would be retained after partial removal, with above 90% retention expected for both metrics on many platforms. Partial removal would likely result in the loss of fish biomass and production for species typically found residing in the shallow portions of the platform structure. However, these fishes generally represent a small proportion of the fishes associated with these platforms. More characteristic of platform fauna are the primarily deeper-dwelling rockfishes (genus Sebastes. "Shell mounds" are biogenic reefs that surround some of these platforms resulting from an accumulation of mollusk shells that have fallen from the shallow areas of the platforms mostly above the depth of partial removal. We found that shell mounds are moderately productive fish habitats, similar to or greater than natural rocky reefs in the region at comparable depths. The complexity and areal extent of these biogenic habitats, and the associated fish biomass and production, will likely be reduced after either partial or complete platform removal. Habitat augmentation by placing the partially removed platform superstructure or some other additional habitat enrichment material (e.g., rock boulders on the seafloor adjacent to the base of partially removed platforms provides additional options to enhance fish production, potentially mitigating reductions in shell mound habitat.

  5. Impacts from Partial Removal of Decommissioned Oil and Gas Platforms on Fish Biomass and Production on the Remaining Platform Structure and Surrounding Shell Mounds.

    Science.gov (United States)

    Claisse, Jeremy T; Pondella, Daniel J; Love, Milton; Zahn, Laurel A; Williams, Chelsea M; Bull, Ann S

    2015-01-01

    When oil and gas platforms become obsolete they go through a decommissioning process. This may include partial removal (from the surface to 26 m depth) or complete removal of the platform structure. While complete removal would likely eliminate most of the existing fish biomass and associated secondary production, we find that the potential impacts of partial removal would likely be limited on all but one platform off the coast of California. On average 80% of fish biomass and 86% of secondary fish production would be retained after partial removal, with above 90% retention expected for both metrics on many platforms. Partial removal would likely result in the loss of fish biomass and production for species typically found residing in the shallow portions of the platform structure. However, these fishes generally represent a small proportion of the fishes associated with these platforms. More characteristic of platform fauna are the primarily deeper-dwelling rockfishes (genus Sebastes). "Shell mounds" are biogenic reefs that surround some of these platforms resulting from an accumulation of mollusk shells that have fallen from the shallow areas of the platforms mostly above the depth of partial removal. We found that shell mounds are moderately productive fish habitats, similar to or greater than natural rocky reefs in the region at comparable depths. The complexity and areal extent of these biogenic habitats, and the associated fish biomass and production, will likely be reduced after either partial or complete platform removal. Habitat augmentation by placing the partially removed platform superstructure or some other additional habitat enrichment material (e.g., rock boulders) on the seafloor adjacent to the base of partially removed platforms provides additional options to enhance fish production, potentially mitigating reductions in shell mound habitat. PMID:26332384

  6. Radioactive iodine removing device

    International Nuclear Information System (INIS)

    In a radioactive iodine removing device of an off-gas processing step in a spent fuel reprocessing facility, spiral structures having an inclination of more than about 20deg is disposed at the inside of an iodine adsorbent packing portion, and dampers are disposed at a packing inlet and a discharging exit for iodine adsorbents respectively. After completion of discharge of the iodine adsorbents, a damper disposed in the midway of a adsorbent packing pipeline is opened for packing the iodine absorbents. The iodine adsorbents used have a spherical shape of 10 to 20 mesh (1 to 2mm), and the adsorbents are packed uniformly both radially and vertically to the packing portion upon injection of the adsorbents and, as a result, the packing portion can be made compact. Further, since the discharged iodine adsorbents can be contained in a vessel directly or in a different vessel having an excellent containing performance by taking the dimension of the vessel into consideration, it is possible to reduce the generation amount of wastes than that in a conventional case. (N.H.)

  7. Projects Work!

    Science.gov (United States)

    Textor, Martin R.

    2005-01-01

    The great educational value of projects is emphasized by contrasting negative aspects of the life of today's children with the goals of project work. This is illustrated by a project "Shopping." It is shown what children are learning in such projects and what the advantages of project work are. Relevant topic areas, criteria for selecting a…

  8. Mixing and In situ product removal in micro-bioreactors

    NARCIS (Netherlands)

    Li, X.

    2009-01-01

    Summary Of the thesis :’ Mixing and In-situ product removal in micro bioreactors’ by Xiaonan Li The work presented in this thesis is a part of a large cluster project, which was formed between DSM, Organon, Applikon and two university groups (TU Delft and University of Twente), under the ACTS and

  9. Reflections on a Pilot Project: Removing the "Dis" from Disability

    Science.gov (United States)

    Yee, Michelle J.

    2012-01-01

    This paper explores preliminary results of a pilot study whose purpose was to document, through an oral history narrative, the personal and work experiences of a female artist and social entrepreneur who is legally blind. These experiences included the challenges that the research participant has experienced in the U.S. as a woman with an…

  10. Enabling Large-body Active Debris Removal Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Research suggests that: (1) orbital debris has reached the point that, even with no future launches, collisions among large-body debris will lead to unstable growth...

  11. Enabling Large-body Active Debris Removal Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Research suggests that: (1) orbital debris has reached an unstable point whereby, even with no future launches, the amount of debris will continue to grow through...

  12. Transparent and Flexible Electrodynamic Coating for Particulate Removal Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA has an unmet need for clean, dust-free surfaces critical for many mission applications: solar panels and collectors, aircraft components, optical windows,...

  13. Removing Mid-Spatial Frequency Errors with VIBE Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Optimax VIBE finishing process is a fast (<60 second), full-aperture, conformal polishing process incorporating high frequency motion that rapidly eliminates...

  14. Congressionally Directed Project for Passive NOx Removal Catalysts Research

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, William

    2014-08-29

    The Recipient proposes to produce new scientific and technical knowledge and tools to enable the discovery and deployment of highly effective materials for the selective catalytic reduction (SCR) of nitrogen oxides (NOx) from lean combustion exhaust. A second goal is to demonstrate a closely coupled experimental and computational approach to heterogeneous catalysis research. These goals will be met through the completion of four primary technical objectives: First, an in-depth kinetic analysis will be performed on two prominent classes of NOx SCR catalysts, Fe- and Cu-exchanged beta and ZSM-5 zeolites, over a wide range of catalyst formulation and under identical, high conversion conditions as a function of gas phase composition. Second, the nanoscale structure and adsorption chemistry of these high temperature (HT) and low temperature (LT) catalysts will be determined using in situ and operando spectroscopy under the same reaction conditions. Third, first-principles molecular simulations will be used to model the metal-zeolite active sites, their adsorption chemistry, and key steps in catalytic function. Fourth, this information will be integrated into chemically detailed mechanistic and kinetic descriptions and models of the operation of these well- defined NOx SCR catalysts under practically relevant reaction conditions. The new knowledge and models that derive from this work will be published in the scientific literature.

  15. Methods to Remove Coke from Endothermic Heat Exchangers Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Currently the United States space program is recognized as the world leader in providing access to space. However, in order to maintain this position, it will be...

  16. ESTIMATING PERCENT REMOVAL FOR A SOIL VENTING PROJECT.

    Science.gov (United States)

    The USEPA allowed the Performing Parties (PPs) to perform a soil vapor extraction process to a site contaminated by volatile organic compounds (VOC), contingent upon the process reducing the VOC concentrations in the soil by 75% within one year. An innovative injection-extraction...

  17. Methods to Remove Coke from Endothermic Heat Exchangers Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In February 2004 NASA released "The Vision for Space Exploration", which describes a strategy for exploring our solar system that builds upon the policy announced...

  18. Laser assisted graffiti paints removing

    Science.gov (United States)

    Novikov, B. Y.; Chikalev, Y. V.; Shakhno, E. A.

    2011-02-01

    It's hard to imagine a modern city view without some drawings and inscriptions, usually called "graffiti". Traditional cleaning methods do not suit modern requirements. Investigation of possibilities of laser assisted paints removing is described in this article. The conditions for removing different paints from different surfaces were defined.

  19. Krypton-85 removal and storage

    International Nuclear Information System (INIS)

    A literature survey was made in order to predict the atmospheric Kr-85 concentration in the future and it s effect on the population. As a consequence the need for its treatment and removal as a previous step to gaseous waste disposal is justified. A literature review of possible methods of Kr-85 removal and storage is also included. (Author) 43 refs

  20. [Acrylic resin removable partial dentures

    NARCIS (Netherlands)

    Baat, C. de; Witter, D.J.; Creugers, N.H.J.

    2011-01-01

    An acrylic resin removable partial denture is distinguished from other types of removable partial dentures by an all-acrylic resin base which is, in principle, solely supported by the edentulous regions of the tooth arch and in the maxilla also by the hard palate. When compared to the other types of

  1. Screw/stud removal tool

    Science.gov (United States)

    Daniels, K.; Herrick, D. E.; Rothermel, L.

    1980-01-01

    Tool removes stubborn panheaded screws or studs where conventional tools would be either too weak or inconvenient to use. Screws with damaged heads or slots can also be removed this way. Tool can be worked with one hand and easily fits limited-access and blind areas. It can be made in various sizes to fit different screwheads.

  2. Laser assisted hair-removal.

    Science.gov (United States)

    Choudhary, S; Elsaie, M L; Nouri, K

    2009-10-01

    A number of lasers and light devices are now available for the treatment of unwanted hair. The goal of laser hair removal is to damage stem cells in the bulge of the hair follicle by targeting melanin, the endogenous chromophore for laser and light devices utilized to remove hair. The competing chromophores in the skin and hair, oxyhemoglobin and water, have a decreased absorption between 690 nm and 1000 nm, thus making this an ideal range for laser and light sources. Laser hair removal is achieved through follicular unit destruction based on selective photothermolysis. The principle of selective photothermolysis predicts that the thermal injury will be restricted to a given target if there is sufficient selective absorption of light and the pulse duration is shorter than the thermal relaxation time of the target. This review will focus on the mechanisms of laser assisted hair removal and provide an update on the newer technologies emerging in the field of lasers assisted hair removal.

  3. Intending Projects

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Project name: 90,000t/a BR device and auxiliary projects Construction unit: Sinopec Beijing Yanshan Petrochemical Company Total investment: 2.257 billion yuan Project description: It will cover an area of 14. lha.

  4. CPP-603 Chloride Removal System Decontamination and Decommissioning

    International Nuclear Information System (INIS)

    The CPP-603 (annex) Chloride Removal System (CRS) Decontamination and Decommissioning (D ampersand D) Project is described in this report. The CRS was used for removing Chloride ions and other contaminants that were suspended in the waters of the underwater fuel storage basins in the CPP-603 Fuel Receiving and Storage Facility (FRSF) from 1975 to 1981. The Environmental Checklist and related documents, facility characterization, decision analysis', and D ampersand D plans' were prepared in 1991. Physical D ampersand D activities were begun in mid summer of 1992 and were completed by the end of November 1992. All process equipment and electrical equipment were removed from the annex following accepted asbestos and radiological contamination removal practices. The D ampersand D activities were performed in a manner such that no radiological health or safety hazard to the public or to personnel at the Idaho National Engineering Laboratory (INEL) occurred

  5. A Hidden-Removal Model of Dam Perspective Drawing

    Institute of Scientific and Technical Information of China (English)

    WANG Zi-ru; ZHOU Hui-cheng; LI Ming-qiu

    2011-01-01

    Aming at water conservancy project visualization, a hidden-removal method of dam perspective drawings is realized by building a hidden-removal mathematical model for overlapping points location to set up the hidden relationship among point and plane, plane and plane in space. On this basis, as an example of panel rockfill dam, a dam hidden-removal perspective drawing is generated in different directions and different visual angles through adapting VC++ and OpenGL visualizing technology. The results show that the data construction of the model is simple which can overcome the disadvantages of considerable and complicated calculation. This method also provides the new means to draw hidden-removal perspective drawings for those landforms and ground objects.

  6. Human-Systems Integration Processes (HSIP) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In FY12, this project removed the commercial-specific content from the Commercial Human-Systems Integration Design Processes (CHSIP), identified gaps in the...

  7. Removal of barium and radium from groundwater. Environmental research brief

    International Nuclear Information System (INIS)

    A research project was undertaken to investigate processes for removing barium and radium from drinking water. Special emphasis was placed on ion exchange processes that can be used without adding large concentrations of sodium to the water. The wastes from radium and barium removal processes were also characterized, and processes suitable for treatment of ion-exchange brines were evaluated. The report discusses two ion-exchange processes that can be used for barium and radium removal accompanied by either partial or no hardness removal. The calcium-form, strong-acid ion-exchange resin can be used for barium and radium removal without significant change in hardness or the concentration of other salts. This resin can be regenerated with CaC12 brine. The radium-selective complexer (RSC) will remove radium without altering hardness or other salt concentration. The capacity of this resin for waters with low total dissolved solids (TDS) (<1000 to 2000 mg/L TDS) is in excess of 30,000 pCi/dry g; however, if the TDS is increased to about 40,000 mg/L, the capacity drops to 200 to 300 pCi/dry g. Thus using this resin to remove radium from spent brine does not appear feasible

  8. PRECOMBUSTION REMOVAL OF HAZARDOUS AIR POLLUTANT PRECURSORS

    Energy Technology Data Exchange (ETDEWEB)

    Unknown

    2000-10-09

    In response to growing environmental concerns reflected in the 1990 Clean Air Act Amendment (CAAA), the United States Department of Energy (DOE) sponsored several research and development projects in late 1995 as part of an initiative entitled Advanced Environmental Control Technologies for Coal-Based Power Systems. The program provided cost-shared support for research and development projects that could accelerate the commercialization of affordable, high-efficiency, low-emission, coal-fueled electric generating technologies. Clean coal technologies developed under this program would serve as prototypes for later generations of technologies to be implemented in the industrial sector. In order to identify technologies with the greatest potential for commercial implementation, projects funded under Phase I of this program were subject to competitive review by DOE before being considered for continuation funding under Phase II. One of the primary topical areas identified under the DOE initiative relates to the development of improved technologies for reducing the emissions of air toxics. Previous studies have suggested that many of the potentially hazardous air pollutant precursors (HAPPs) occur as trace elements in the mineral matter of run-of-mine coals. As a result, these elements have the potential to be removed prior to combustion at the mine site by physical coal cleaning processes (i.e., coal preparation). Unfortunately, existing coal preparation plants are generally limited in their ability to remove HAPPs due to incomplete liberation of the mineral matter and high organic associations of some trace elements. In addition, existing physical coal cleaning plants are not specifically designed or optimized to ensure that high trace element rejections may be achieved.

  9. Large diameter, deep water pipelay Zeepipe IIA project

    Energy Technology Data Exchange (ETDEWEB)

    Farley, S.D.; Sykes, C.; Simons, P. [European Marine Contractors Ltd., Motspur Park (United Kingdom)

    1996-12-01

    The 300 km Zeepipe IIA offshore gas pipeline was installed by European marine Contractors Ltd. for Statoil between the Sleipner A Platform and the Kollsness Terminal tunnel exit in the 1994 and 1995 lay seasons. The route passes through the Norwegian Trench and the highly undulating nearshore area at Oygarden. While smaller pipes have been laid in deeper water, with a diameter of 40 inches and a maximum water depth of 365 meters this pipeline represents the most technically demanding combination of diameter and water depth laid in the world to date. The project faced specific challenges, including high lay tensions, heavily concrete coated pipe, pipeline laydown and recovery in deep water, subsea pockmark and boulder fields, stringent lay tolerances and low residual tension requirements. This paper details the planning, installation engineering, equipment modification and innovations required to achieve successful completion of the pipeline installation.

  10. Arrhythmia management after device removal.

    Science.gov (United States)

    Nishii, Nobuhiro

    2016-08-01

    Arrhythmic management is needed after removal of cardiac implantable electronic devices (CIEDs). Patients completely dependent on CIEDs need temporary device back-up until new CIEDs are implanted. Various methods are available for device back-up, and the appropriate management varies among patients. The duration from CIED removal to implantation of a new CIED also differs among patients. Temporary pacing is needed for patients with bradycardia, a wearable cardioverter defibrillator (WCD) or catheter ablation is needed for patients with tachyarrhythmia, and sequential pacing is needed for patients dependent on cardiac resynchronization therapy. The present review focuses on arrhythmic management after CIED removal. PMID:27588151

  11. Midway Atoll - Ironwood Removal for Dune Restoration and Sea Level Rise Resiliency

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The proposed project consists of removal of invasive, non-native ironwood trees (Casuarina equisetifolia) from approximately 40 acres of high priority coastal...

  12. Project Management

    DEFF Research Database (Denmark)

    Project Management Theory Meets Practice contains the proceedings from the 1st Danish Project Management Research Conference (DAPMARC 2015), held in Copenhagen, Denmark, on May 21st, 2015.......Project Management Theory Meets Practice contains the proceedings from the 1st Danish Project Management Research Conference (DAPMARC 2015), held in Copenhagen, Denmark, on May 21st, 2015....

  13. Project Management

    DEFF Research Database (Denmark)

    Pilkington, Alan; Chai, Kah-Hin; Le, Yang

    2015-01-01

    This paper identifies the true coverage of PM theory through a bibliometric analysis of the International Journal of Project Management from 1996-2012. We identify six persistent research themes: project time management, project risk management, programme management, large-scale project management......, project success/failure and practitioner development. These differ from those presented in review and editorial articles in the literature. In addition, topics missing from the PM BOK: knowledge management project-based organization and project portfolio management have become more popular topics...

  14. 78 FR 68995 - Safety Zone: Vessel Removal From the Oakland Estuary, Alameda, CA

    Science.gov (United States)

    2013-11-18

    ...: Table of Acronyms DHS Department of Homeland Security FR Federal Register NPRM Notice of Proposed... SECURITY Coast Guard 33 CFR Part 165 RIN 1625-AA00 Safety Zone: Vessel Removal From the Oakland Estuary... Street Bridge in Alameda, CA in support of the Oakland Estuary Closure for the Vessel Removal Project...

  15. 77 FR 56189 - Proposed Information Collection; Comment Request; Elwha River Dam Removal and Floodplain...

    Science.gov (United States)

    2012-09-12

    ... River Dam Removal and Floodplain Restoration Ecosystem Service Valuation Pilot Project AGENCY: National... Elwha River Dam Removal and Floodplain Restoration Ecosystem Service Valuation Survey it has developed... American tribes for whom the river has cultural, environmental, and economic significance. The dam...

  16. Inked and Regretful: Removing Tattoos

    Science.gov (United States)

    ... For Consumers Consumer Updates Inked and Regretful: Removing Tattoos Share Tweet Linkedin Pin it More sharing options ... How Does It Work? Does It Hurt? That tattoo on your arm of a former flame—the ...

  17. Can Acne Scars Be Removed?

    Science.gov (United States)

    ... Can I Help a Friend Who Cuts? Can Acne Scars Be Removed? KidsHealth > For Teens > Can Acne ... eliminarse las marcas de acne? Different Types of Acne Scars from acne can seem like double punishment — ...

  18. Removal of root filling materials.

    LENUS (Irish Health Repository)

    Duncan, H.F. Chong, B.S.

    2011-05-01

    Safe, successful and effective removal of root filling materials is an integral component of non-surgical root canal re-treatment. Access to the root canal system must be achieved in order to negotiate to the canal terminus so that deficiencies in the original treatment can be rectified. Since a range of materials have been advocated for filling root canals, different techniques are required for their removal. The management of commonly encountered root filling materials during non-surgical re-treatment, including the clinical procedures necessary for removal and the associated risks, are reviewed. As gutta-percha is the most widely used and accepted root filling material, there is a greater emphasis on its removal in this review.

  19. Heat exchanger with removable orifice

    International Nuclear Information System (INIS)

    A nuclear reactor steam generator heat exchanger is described which has orifices in the entrance openings of the heat exchange tubes which, although securely fastened to the tubes, can be easily removed by remote handling equipment. (U.K.)

  20. Contaminated concrete surface layer removal

    International Nuclear Information System (INIS)

    Equipment is being developed to economically remove contaminated concrete surfaces in nuclear facilities. To be effective this equipment should minimize personnel radiation exposure, minimize the volume of material removed, and perform the operation quickly with the least amount of energy. Several methods for removing concrete surfaces are evaluated for use in decontaminating such facilities. Two unique methods especially suited for decontamination are described: one, the water cannon, is a device that fires a high-velocity jet of fluid causing spallation of the concrete surface; the other, a concrete spaller, is a tool that exerts radial pressure agains the sides of a pre-dilled shallow cylindrical hole causing spallation to occur. Each method includes a means for containing airborne contamination. Results of tests show that these techniques can rapidly and economically remove surfaces, and leave minimal rubble for controlled disposal

  1. Tokai-1 decommissioning project

    International Nuclear Information System (INIS)

    Tokai-1 (GCR, Gas Cooled Reactor) nuclear power plant of JAPC (the Japan Atomic Power Company) started commercial operation in 1966 as the first commercial nuclear power plant in Japan. The unit had helped introduction and establishment of the construction and operation technologies regarding nuclear power plant at early stage in Japan by its construction and operating experiences. However, The Japan Atomic Power Company (JAPC), the operator and owner of Tokai-1, decided to cease its operation permanently because of a fulfillment of its mission and economical reason. The unit was finally shut down in March 1998 after about 32 year operation. It took about three years for removal of all spent fuels from the site, and then decommissioning started in 2001. JAPC, always on the forefront of the nation's nuclear power generation, is now grappling Japan's first decommissioning of a commercial nuclear power plant, striving to establish effective, advanced decommissioning. The decommissioning for Tokai-1 was scheduled as 20 years project. At the beginning, the reactor was started to be in a static condition ('safe storage period'). While the reactor had been safely stored, the phased decommissioning works started from non-radioactive or low radioactive equipment toward high radioactive equipment. First five years of the project, JAPC concentrated to drain and clean spent fuel cartridge cooling pond and to remove conventional equipments such as turbine, feed water pump and fuel charge machine as planed and budgeted. From 2006, the project came into a new phase. JAPC has been trying to remove four Steam Raising Units (SRUs). The SRUs are huge component (750ton, φ6.3m, H24.7m) of the Gas Cooling Reactor (GCR) and inside of the SRUs are radioactively contaminated. Major concerns are workers safety and minimizing contamination areas during SRU removal. Therefore, JAPC is developing and introducing Jack-down method and remote control multi-functional dismantling system. This

  2. Water Recycling removal using temperature-sensitive hydronen

    Energy Technology Data Exchange (ETDEWEB)

    Rana B. Gupta

    2002-10-30

    The overall objective of this project was to study the proposed Water Recycling/Removal Using Temperature-Sensitive Hydrogels. The main element of this technology is the design of a suitable hydrogel that can perform needed water separation for pulp and paper industry. The specific topics studied are to answer following questions: (a) Can water be removed using hydrogel from large molecules such as lignin? (b) Can the rate of separation be made faster? (c) What are the molecular interactions with hydrogel surface? (d) Can a hydrogel be designed for a high ionic strength and high temperature? Summary of the specific results are given.

  3. Colorado Better Buildings Project Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Strife, Susie; Yancey, Lea

    2013-12-30

    The Colorado Better Buildings project intended to bring new and existing energy efficiency model programs to market with regional collaboration and funding partnerships. The goals for Boulder County and its program partners were to advance energy efficiency investments, stimulate economic growth in Colorado and advance the state’s energy independence. Collectively, three counties set out to complete 9,025 energy efficiency upgrades in 2.5 years and they succeeded in doing so. Energy efficiency upgrades have been completed in more than 11,000 homes and businesses in these communities. Boulder County and its partners received a $25 million BetterBuildings grant from the U.S. Department of Energy under the American Recovery and Reinvestment Act in the summer of 2010. This was also known as the Energy Efficiency and Conservation Block Grants program. With this funding, Boulder County, the City and County of Denver, and Garfield County set out to design programs for the residential and commercial sectors to overcome key barriers in the energy upgrade process. Since January 2011, these communities have paired homeowners and business owners with an Energy Advisor – an expert to help move from assessment to upgrade with minimal hassle. Pairing this step-by-step assistance with financing incentives has effectively addressed many key barriers, resulting in energy efficiency improvements and happy customers. An expert energy advisor guides the building owner through every step of the process, coordinating the energy assessment, interpreting results for a customized action plan, providing a list of contractors, and finding and applying for all available rebates and low-interest loans. In addition to the expert advising and financial incentives, the programs also included elements of social marketing, technical assistance, workforce development and contractor trainings, project monitoring and verification, and a cloud-based customer data system to coordinate among field

  4. Annual Progress Report Fish Research Project Oregon : Project title, Evaluation of Habitat Improvements -- John Day River.

    Energy Technology Data Exchange (ETDEWEB)

    Olsen, Erik A.

    1984-01-01

    This report summarizes data collected in 1983 to evaluate habitat improvements in Deer, Camp, and Clear creeks, tributaries of the John Day River. The studies are designed to evaluate changes in abundance of spring chinook and summer steelhead due to habitat improvement projects and to contrast fishery benefits with costs of construction and maintenance of each project. Structure types being evaluated are: (1) log weirs, rock weirs, log deflectors, and in stream boulders in Deer Creek; (2) log weirs in Camp Creek; and (3) log weir-boulder combinations and introduced spawning gravel in Clear Creek. Abundance of juvenile steelhead ranged from 16% to 119% higher in the improved (treatment) area than in the unimproved (control) area of Deer Creek. However, abundance of steelhead in Camp Creek was not significantly different between treatment and control areas. Chinook and steelhead abundance in Clear Creek was 50% and 25% lower, respectively in 1983, than the mean abundance estimated in three previous years. The age structure of steelhead was similar between treatment and control areas in Deer and Clear creeks. The treatment area in Camp Creek, however, had a higher percentage of age 2 and older steelhead than the control. Steelhead redd counts in Camp Creek were 36% lower in 1983 than the previous five year average. Steelhead redd counts in Deer Creek were not made in 1983 because of high streamflows. Chinook redds counted in Clear Creek were 64% lower than the five year average. Surface area, volume, cover, and spawning gravel were the same or higher than the corresponding control in each stream except in Deer Creek where there was less available cover and spawning gravel in sections with rock weirs and in those with log deflectors, respectively. Pool:riffle ratios ranged from 57:43 in sections in upper Clear Creek with log weirs to 9:91 in sections in Deer Creek with rock weirs. Smolt production following habitat improvements is estimated for each stream

  5. AX Tank Farm tank removal study

    Energy Technology Data Exchange (ETDEWEB)

    SKELLY, W.A.

    1999-02-24

    This report examines the feasibility of remediating ancillary equipment associated with the 241-AX Tank Farm at the Hanford Site. Ancillary equipment includes surface structures and equipment, process waste piping, ventilation components, wells, and pits, boxes, sumps, and tanks used to make waste transfers to/from the AX tanks and adjoining tank farms. Two remedial alternatives are considered: (1) excavation and removal of all ancillary equipment items, and (2) in-situ stabilization by grout filling, the 241-AX Tank Farm is being employed as a strawman in engineering studies evaluating clean and landfill closure options for Hanford single-shell tanks. This is one of several reports being prepared for use by the Hanford Tanks Initiative Project to explore potential closure options and to develop retrieval performance evaluation criteria for tank farms.

  6. AX Tank Farm tank removal study

    Energy Technology Data Exchange (ETDEWEB)

    SKELLY, W.A.

    1998-10-14

    This report considers the feasibility of exposing, demolishing, and removing underground storage tanks from the 241-AX Tank Farm at the Hanford Site. For the study, it was assumed that the tanks would each contain 360 ft{sup 3} of residual waste (corresponding to the one percent residual Inventory target cited in the Tri-Party Agreement) at the time of demolition. The 241-AX Tank Farm is being employed as a ''strawman'' in engineering studies evaluating clean and landfill closure options for Hanford single-shell tank farms. The report is one of several reports being prepared for use by the Hanford Tanks Initiative Project to explore potential closure options and to develop retrieval performance evaluation criteria for tank farms.

  7. AX Tank Farm tank removal study

    International Nuclear Information System (INIS)

    This report considers the feasibility of exposing, demolishing, and removing underground storage tanks from the 241-AX Tank Farm at the Hanford Site. For the study, it was assumed that the tanks would each contain 360 ft3 of residual waste (corresponding to the one percent residual Inventory target cited in the Tri-Party Agreement) at the time of demolition. The 241-AX Tank Farm is being employed as a ''strawman'' in engineering studies evaluating clean and landfill closure options for Hanford single-shell tank farms. The report is one of several reports being prepared for use by the Hanford Tanks Initiative Project to explore potential closure options and to develop retrieval performance evaluation criteria for tank farms

  8. Removing Pubic Hair (For Young Women)

    Science.gov (United States)

    ... Gynecology Medical Conditions Nutrition & Fitness Emotional Health Removing Pubic Hair Posted under Health Guides . Updated 7 October 2015. + ... safety guidelines if you decide to remove pubic hair. Removing pubic hair is a personal preference. Some girls trim ...

  9. K basins sludge removal sludge pretreatment system

    International Nuclear Information System (INIS)

    The Spent Nuclear Fuels Program is in the process of planning activities to remove spent nuclear fuel and other materials from the 100-K Basins as a remediation effort for clean closure. The 105 K- East and K-West Basins store spent fuel, sludge, and debris. Sludge has accumulated in the 1 00 K Basins as a result of fuel oxidation and a slight amount of general debris being deposited, by settling, in the basin water. The ultimate intent in removing the sludge and fuel is to eliminate the environmental risk posed by storing fuel at the K Basins. The task for this project is to disposition specific constituents of sludge (metallic fuel) to produce a product stream through a pretreatment process that will meet the requirements, including a final particle size acceptable to the Tank Waste Remediation System (TWRS). The purpose of this task is to develop a preconceptual design package for the K Basin sludge pretreatment system. The process equipment/system is at a preconceptual stage, as shown in sketch ES-SNF-01 , while a more refined process system and material/energy balances are ongoing (all sketches are shown in Appendix C). Thus, the overall process and 0535 associated equipment have been conservatively selected and sized, respectively, to establish the cost basis and equipment layout as shown in sketches ES- SNF-02 through 08

  10. High removal rate laser-based coating removal system

    Science.gov (United States)

    Matthews, Dennis L.; Celliers, Peter M.; Hackel, Lloyd; Da Silva, Luiz B.; Dane, C. Brent; Mrowka, Stanley

    1999-11-16

    A compact laser system that removes surface coatings (such as paint, dirt, etc.) at a removal rate as high as 1000 ft.sup.2 /hr or more without damaging the surface. A high repetition rate laser with multiple amplification passes propagating through at least one optical amplifier is used, along with a delivery system consisting of a telescoping and articulating tube which also contains an evacuation system for simultaneously sweeping up the debris produced in the process. The amplified beam can be converted to an output beam by passively switching the polarization of at least one amplified beam. The system also has a personal safety system which protects against accidental exposures.

  11. Laser assisted hair-removal.

    Science.gov (United States)

    Choudhary, S; Elsaie, M L; Nouri, K

    2009-10-01

    A number of lasers and light devices are now available for the treatment of unwanted hair. The goal of laser hair removal is to damage stem cells in the bulge of the hair follicle by targeting melanin, the endogenous chromophore for laser and light devices utilized to remove hair. The competing chromophores in the skin and hair, oxyhemoglobin and water, have a decreased absorption between 690 nm and 1000 nm, thus making this an ideal range for laser and light sources. Laser hair removal is achieved through follicular unit destruction based on selective photothermolysis. The principle of selective photothermolysis predicts that the thermal injury will be restricted to a given target if there is sufficient selective absorption of light and the pulse duration is shorter than the thermal relaxation time of the target. This review will focus on the mechanisms of laser assisted hair removal and provide an update on the newer technologies emerging in the field of lasers assisted hair removal. PMID:19834437

  12. Technetium removal from aqueous wastes

    International Nuclear Information System (INIS)

    The research discussed in this report has compared several ''state of the art'' techniques for the removal of traces of the radionuclide, technetium, from aqueous wastes. The techniques investigated were: electrochemical reduction to an insoluble oxide, electrochemical ion exchange, seeded ultrafiltration and chemical reduction followed by filtration. Each technique was examined using a simulant based upon the waste generated by the Enhanced Actinide Removal Plant (EARP) at Sellafield. The technique selected for further investigation was direct electrochemical reduction which offers an ideal route for the removal of technetium from the stream (DFs 10-100) and can be operated continuously with a low power consumption 25 kW for the waste generated by EARP. Cell designs for scale up have been suggested to treat the 1000m3 of waste produced every day. Future work is proposed to investigate the simultaneous removal of other key radionuclides, such as ruthenium, plutonium and cobalt as well as scale up of the resulting process and to investigate the effect of these other radionuclides on the efficiency of the electrochemical reduction technique for the removal of technetium. Total development and full scale plant costs are estimated to be of the order of 5 pounds - 10M, with a time scale of 5 -8 years to realisation. (author)

  13. Tidd PFBC demonstration project

    Energy Technology Data Exchange (ETDEWEB)

    Marrocco, M. [American Electric Power, Columbus, OH (United States)

    1997-12-31

    The Tidd project was one of the first joint government-industry ventures to be approved by the US Department of Energy (DOE) in its Clean Coal Technology Program. In March 1987, DOE signed an agreement with the Ohio Power Company, a subsidiary of American Electric Power, to refurbish the then-idle Tidd plant on the banks of the Ohio River with advanced pressurized fluidized bed technology. Testing ended after 49 months of operation, 100 individual tests, and the generation of more than 500,000 megawatt-hours of electricity. The demonstration plant has met its objectives. The project showed that more than 95 percent of sulfur dioxide pollutants could be removed inside the advanced boiler using the advanced combustion technology, giving future power plants an attractive alternative to expensive, add-on scrubber technology. In addition to its sulfur removal effectiveness, the plant`s sustained periods of steady-state operation boosted its availability significantly above design projections, heightening confidence that pressurized fluidized bed technology will be a reliable, baseload technology for future power plants. The technology also controlled the release of nitrogen oxides to levels well below the allowable limits set by federal air quality standards. It also produced a dry waste product that is much easier to handle than wastes from conventional power plants and will likely have commercial value when produced by future power plants.

  14. Project Temporalities

    DEFF Research Database (Denmark)

    Tryggestad, Kjell; Justesen, Lise; Mouritsen, Jan

    2013-01-01

    into account. This may require investments in new project management technologies. Originality/value – This paper adds to the literatures on project temporalities and stakeholder theory by connecting them to the question of non-human stakeholders and to project management technologies.......Purpose – The purpose of this paper is to explore how animals can become stakeholders in interaction with project management technologies and what happens with project temporalities when new and surprising stakeholders become part of a project and a recognized matter of concern to be taken...... into account. Design/methodology/approach – The paper is based on a qualitative case study of a project in the building industry. The authors use actor-network theory (ANT) to analyze the emergence of animal stakeholders, stakes and temporalities. Findings – The study shows how project temporalities can...

  15. Intending Projects

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Project name: New construction project of production,research & development base of hydraulic system Construction site: Qingpu Industrial Park Construction unit: Parker Hannifin Industrial Hydraulic Technology (Shanghai) Co., Ltd.

  16. Alzheimer's Project

    Medline Plus

    Full Text Available ... Momentum in Science, Part 2" (70 minutes) Be a part of something big. HBO's "THE ALZHEIMER'S PROJECT" ... vital research and services. "THE ALZHEIMER'S PROJECT" is a presentation of HBO Documentary Films and the National ...

  17. Alzheimer's Project

    Science.gov (United States)

    ... state Home > News & Events > Upcoming Events > HBO Alzheimer’s Project In the News Walk to End Alzheimer's Upcoming ... Disease Awareness Month World Alzheimer's Month HBO Alzheimer’s Project MAKE A DONATION Your gift will help us ...

  18. Virtual projects

    DEFF Research Database (Denmark)

    Svejvig, Per; Commisso, Trine Hald

    2012-01-01

    Virtual projects are common with global competition, market development, and not least the financial crisis forcing organizations to reduce their costs drastically. Organizations therefore have to place high importance on ways to carry out virtual projects and consider appropriate practices...... that the best practice knowledge has not permeated sufficiently to the practice. Furthermore, the appropriate application of information and communication technology (ICT) remains a big challenge, and finally project managers are not sufficiently trained in organizing and conducting virtual projects...

  19. Project Management

    OpenAIRE

    Lörinc, Jan

    2012-01-01

    This work deals with the problems in the process of project management in enterprises. It examines the precise approaches, the possibility of standardizingthe approach to project team management and motivation of its members and their role in the process of project management. He confronts the views and attitudes of selected authors. The theoretical conclusions of findings compares with knowledgeacquired from research carried out on project management in a selected company.Evaluates managemen...

  20. Project ethics

    CERN Document Server

    Jonasson, Haukur Ingi

    2013-01-01

    How relevant is ethics to project management? The book - which aims to demystify the field of ethics for project managers and managers in general - takes both a critical and a practical look at project management in terms of success criteria, and ethical opportunities and risks. The goal is to help the reader to use ethical theory to further identify opportunities and risks within their projects and thereby to advance more directly along the path of mature and sustainable managerial practice.

  1. PHOSPHORUS REMOVAL USING STEEL SLAG

    Institute of Scientific and Technical Information of China (English)

    Y.Z. Lan; S. Zhang; J.K. Wang; R. W. Smith

    2006-01-01

    Steel slag is a byproduct produced in large amounts in the steel-making process. It is an important resource that can be effectively utilized. An experiment was described in which steel slag was tested as an adsorbent for the removal of phosphorus from waste water. Phosphorus removal depended on the amount of steel slag added, the pH value, the contact time, and the initial concentration. Under laboratory conditions when the added slag was 7.5g/L, the contact time 2h, and the pH value was equivalent to 6.5, over 99% of the phosphorus was removed; the experimental data on steel slag adsorption of phosphorus in the water fitted the Freundlich isotherm model. Steel slag was found to be very effective in adsorbing phosphorus.

  2. AdapterRemoval v2

    DEFF Research Database (Denmark)

    Schubert, Mikkel; Lindgreen, Stinus; Orlando, Ludovic

    2016-01-01

    process the growing amount of data generated per sequencing run. FINDINGS: We introduce AdapterRemoval v2, a major revision of AdapterRemoval v1, which introduces (i) striking improvements in throughput, through the use of single instruction, multiple data (SIMD; SSE1 and SSE2) instructions and multi......-threading support, (ii) the ability to handle datasets containing reads or read-pairs with different adapters or adapter pairs, (iii) simultaneous demultiplexing and adapter trimming, (iv) the ability to reconstruct adapter sequences from paired-end reads for poorly documented data sets, and (v) native gzip and...... bzip2 support. CONCLUSIONS: We show that AdapterRemoval v2 compares favorably with existing tools, while offering superior throughput to most alternatives examined here, both for single and multi-threaded operations....

  3. Carious dentine removal: current approach

    Directory of Open Access Journals (Sweden)

    Germana Coeli de Farias Sales

    2008-01-01

    Full Text Available Dentistry is renewed day after day through the results of qualified researches. The approach as regards carious dentin removal is goingthrough questioning and innovation. The scope of this study was to perform a literature review in the sense of elucidating questions pertaining to the problem of whether or not it is necessary to completely remove carious dentin, and the possibility of performing restoration in a single session, in addition to a discussion about which type of material should be applied in this type of substrate. After analyzing the referenced articles, it was concluded that the stepwise treatment controls caries progression; there is a trend in the literature to partially remove the carious dentin in deep lesions and perform definitive restoration; Calcium hydroxide cement is a classical liner in these situations, while glass ionomer cement and resinous materials are other possibilities of materials that can be in close contact with the remaining dentin.

  4. Define Project

    DEFF Research Database (Denmark)

    Munk-Madsen, Andreas

    2005-01-01

    "Project" is a key concept in IS management. The word is frequently used in textbooks and standards. Yet we seldom find a precise definition of the concept. This paper discusses how to define the concept of a project. The proposed definition covers both heavily formalized projects and informally ...

  5. International Projects

    CERN Document Server

    2002-01-01

    Description of co-operation projects implemented with the help of Sweden is presented. Information on performance of Phare and IAEA Regional and National Technical Cooperation projects is provided. Phare project 'Creation of Radiation Protection Infrastructure and Development of Supporting Services' was started in 2002

  6. Map Projection

    CERN Document Server

    Ghaderpour, Ebrahim

    2014-01-01

    In this paper, we introduce some known map projections from a model of the Earth to a flat sheet of paper or map and derive the plotting equations for these projections. The first fundamental form and the Gaussian fundamental quantities are defined and applied to obtain the plotting equations and distortions in length, shape and size for some of these map projections.

  7. Instrument validation project

    Energy Technology Data Exchange (ETDEWEB)

    Reynolds, B.A.; Daymo, E.A.; Geeting, J.G.H.; Zhang, J.

    1996-06-01

    Westinghouse Hanford Company Project W-211 is responsible for providing the system capabilities to remove radioactive waste from ten double-shell tanks used to store radioactive wastes on the Hanford Site in Richland, Washington. The project is also responsible for measuring tank waste slurry properties prior to injection into pipeline systems, including the Replacement of Cross-Site Transfer System. This report summarizes studies of the appropriateness of the instrumentation specified for use in Project W-211. The instruments were evaluated in a test loop with simulated slurries that covered the range of properties specified in the functional design criteria. The results of the study indicate that the compact nature of the baseline Project W-211 loop does not result in reduced instrumental accuracy resulting from poor flow profile development. Of the baseline instrumentation, the Micromotion densimeter, the Moore Industries thermocouple, the Fischer and Porter magnetic flow meter, and the Red Valve Pressure transducer meet the desired instrumental accuracy. An alternate magnetic flow meter (Yokagawa) gave nearly identical results as the baseline fischer and Porter. The Micromotion flow meter did not meet the desired instrument accuracy but could potentially be calibrated so that it would meet the criteria. The Nametre on-line viscometer did not meet the desired instrumental accuracy and is not recommended as a quantitative instrument although it does provide qualitative information. The recommended minimum set of instrumentation necessary to ensure the slurry meets the Project W-058 acceptance criteria is the Micromotion mass flow meter and delta pressure cells.

  8. Instrument validation project

    International Nuclear Information System (INIS)

    Westinghouse Hanford Company Project W-211 is responsible for providing the system capabilities to remove radioactive waste from ten double-shell tanks used to store radioactive wastes on the Hanford Site in Richland, Washington. The project is also responsible for measuring tank waste slurry properties prior to injection into pipeline systems, including the Replacement of Cross-Site Transfer System. This report summarizes studies of the appropriateness of the instrumentation specified for use in Project W-211. The instruments were evaluated in a test loop with simulated slurries that covered the range of properties specified in the functional design criteria. The results of the study indicate that the compact nature of the baseline Project W-211 loop does not result in reduced instrumental accuracy resulting from poor flow profile development. Of the baseline instrumentation, the Micromotion densimeter, the Moore Industries thermocouple, the Fischer and Porter magnetic flow meter, and the Red Valve Pressure transducer meet the desired instrumental accuracy. An alternate magnetic flow meter (Yokagawa) gave nearly identical results as the baseline fischer and Porter. The Micromotion flow meter did not meet the desired instrument accuracy but could potentially be calibrated so that it would meet the criteria. The Nametre on-line viscometer did not meet the desired instrumental accuracy and is not recommended as a quantitative instrument although it does provide qualitative information. The recommended minimum set of instrumentation necessary to ensure the slurry meets the Project W-058 acceptance criteria is the Micromotion mass flow meter and delta pressure cells

  9. Laser-based coatings removal

    Energy Technology Data Exchange (ETDEWEB)

    Freiwald, J.G.; Freiwald, D.A. [F2 Associates, Inc., Albuquerque, NM (United States)

    1995-10-01

    Over the years as building and equipment surfaces became contaminated with low levels of uranium or plutonium dust, coats of paint were applied to stabilize the contaminants in place. Most of the earlier paint used was lead-based paint. More recently, various non-lead-based paints, such as two-part epoxy, are used. For D&D (decontamination and decommissioning), it is desirable to remove the paints or other coatings rather than having to tear down and dispose of the entire building. This report describes the use of pulse-repetetion laser systems for the removal of paints and coatings.

  10. Research reactor decommissioning experience - concrete removal and disposal -

    International Nuclear Information System (INIS)

    Removal and disposal of neutron activated concrete from biological shields is the most significant operational task associated with research reactor decommissioning. During the period of 1985 thru 1989 Chem-Nuclear Systems, Inc. was the prime contractor for complete dismantlement and decommissioning of the Northrop TRIGA Mark F, the Virginia Tech Argonaut, and the Michigan State University TRIGA Mark I Reactor Facilities. This paper discusses operational requirements, methods employed, and results of the concrete removal, packaging, transport and disposal operations for these (3) research reactor decommissioning projects. Methods employed for each are compared. Disposal of concrete above and below regulatory release limits for unrestricted use are discussed. This study concludes that activated reactor biological shield concrete can be safely removed and buried under current regulations

  11. Capital and Operating Costs of Small Arsenic Removal Adsorptive Media Systems

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) conducted 50 full-scale demonstration projects on treatment systems removing arsenic from drinking water in 26 states throughout the U.S. The projects were conducted to evaluate the performance, reliability, and cost of arsenic remo...

  12. Mixing and In situ product removal in micro-bioreactors

    OpenAIRE

    Li, X

    2009-01-01

    Summary Of the thesis :’ Mixing and In-situ product removal in micro bioreactors’ by Xiaonan Li The work presented in this thesis is a part of a large cluster project, which was formed between DSM, Organon, Applikon and two university groups (TU Delft and University of Twente), under the ACTS and IBOS program. The aim of this cluster project was to develop a system consisting of parallel bioreactors of 30 to 200 microliter working volume for the cultivation of micro-organisms under well contr...

  13. Sequestering agents for the removal of actinides from waste streams

    Energy Technology Data Exchange (ETDEWEB)

    Raymond, K.; White, D. [Univ. of California, Berkeley, CA (United States); Whisenhunt, D. [Lawrence Livermore National Lab., CA (United States)

    1996-10-01

    The ultimate goal of this project is to develop new separation technologies to remove radioactive metal ions from contaminated DOE sites. To this end we are studying both the fundamental chemistry and the extractant properties of some chelators that are either found in nature or are closely related to natural materials. The work is a collaboration betwen Lawrence Berkeley National Laboratory-University of California, Berkeley, and the Glenn T. Seaborg Institute for Transactinium Science at Lawrence Livermore National Laboratory.

  14. Arsenic removal by lime softening

    DEFF Research Database (Denmark)

    Kaosol, T.; Suksaroj, C.; Bregnhøj, Henrik

    2002-01-01

    This paper focuses on the study of arsenic removal for drinking water by lime softening. The initial arsenic (V) concentration was 500 and 1,000 ug/L in synthetic groundwater. The experiments were performed as batch tests with varying lime dosages and mixing time. For the synthetic groundwater......, arsenic (V) removal increased with increasing lime dosage and mixing time, as well as with the resulting pH. The residual arsenic (V) in all cases was lower than the WHO guideline of 10 ug/L at pH higher than 11.5. Kinetic of arsenic (V) removal can be described by a first-order equation as C1 = C0*e......^-k*t. The relation between the constant (k value) and increasing lime dosage was found to be linear, described by k = 0.0034 (Dlime). The results support a theory from the literature that the arsenic (V) was removed by precipitation af Ca3(AsO4)2. The results obtained in the present study suggest that lime...

  15. GLYPHOSATE REMOVAL FROM DRINKING WATER

    Science.gov (United States)

    Activated-carbon, oxidation, conventional-treatment, filtration, and membrane studies are conducted to determine which process is best suited to remove the herbicide glyphosate from potable water. Both bench-scale and pilot-scale studies are completed. Computer models are used ...

  16. Removing arsenic from drinking water

    Energy Technology Data Exchange (ETDEWEB)

    Hathaway, S.W.; Rubel, R. (Environmental Protection Agency, Cincinnati, OH (USA))

    1987-08-01

    Pilot-plant tests of two treatment methods, activated alumina and ion exchange, for removing arsenic from drinking water were evaluated at the Fallon, Nevada, Naval Air Station (NAS). The arsenic concentration was 0.080-0.116 mg/liter, exceeding the 0.05 mg/liter maximum contaminant level. Although the valence of arsenic was not determined, in prechlorination process and test results suggest it was probably arsenic V. Chlorinated drinking water from the NAS was used for evaluating the efficacy of treatment under several different conditions. The activated alumina and ion exchange systems were operated through three different loading and regeneration cycles each. The major water quality factors affecting the removal of arsenic by these methods were pH of feedwater, arsenic concentration, sulfate concentration, and alkalinity. The major operational factors affecting removal were flow rate, down time, and media clogging. Capital and operating costs for arsenic removal are estimated for the activated alumina method at optimum pH (5.5) for each of the three small community systems drawing water from the same aquifer. In addition, several containers of the regeneration waste were used for a special study to characterize, dewater, and render the waste non-toxic for disposal in a sanitary landfill.

  17. Removal of siloxanes in biogases.

    Science.gov (United States)

    Schweigkofler, M; Niessner, R

    2001-05-30

    Methods for the removal of gaseous silicon compounds in biogases are presented. In laboratory studies, various solid adsorption materials and liquid absorption solutions were evaluated for their siloxane elimination efficiencies. Among the liquid sorbents studied, concentrated nitric acid and sulfuric acid were found to be especially potent siloxane removing agents at elevated temperature. Solid adsorbents tested include activated charcoal, carbopack B, Tenax TA, XAD II resins, molecular sieve 13X and silica gel. Apart from activated charcoal, silica gel showed especially high adsorption capacities of more than 100mg/g for siloxanes. Furthermore, excellent thermal regeneration of the loaded material was possible. The efficiency of silica gel in removing gaseous siloxanes was verified at a sewage treatment plant, where an adsorption bed with silica gel was used for biogas drying. Other gas pretreatment installations studied included refrigeration condensers and adsorbent beds of meadow ore for the catalytic removal of hydrogen sulfide. In contrast to biogas drying by refrigeration, which had a poor effect on siloxane content, the installation of meadow ore adsorption beds resulted in a significant siloxane reduction of 31-75%, depending on the site studied.

  18. Arsenic Removal by Liquid Membranes

    Directory of Open Access Journals (Sweden)

    Tiziana Marino

    2015-03-01

    Full Text Available Water contamination with harmful arsenic compounds represents one of the most serious calamities of the last two centuries. Natural occurrence of the toxic metal has been revealed recently for 21 countries worldwide; the risk of arsenic intoxication is particularly high in Bangladesh and India but recently also Europe is facing similar problem. Liquid membranes (LMs look like a promising alternative to the existing removal processes, showing numerous advantages in terms of energy consumption, efficiency, selectivity, and operational costs. The development of different LM configurations has been a matter of investigation by several researching groups, especially for the removal of As(III and As(V from aqueous solutions. Most of these LM systems are based on the use of phosphine oxides as carriers, when the metal removal is from sulfuric acid media. Particularly promising for water treatment is the hollow fiber supported liquid membrane (HFSLM configuration, which offers high selectivity, easy transport of the targeted metal ions, large surface area, and non-stop flow process. The choice of organic extractant(s plays an essential role in the efficiency of the arsenic removal. Emulsion liquid membrane (ELM systems have not been extensively investigated so far, although encouraging results have started to appear in the literature. For such LM configuration, the most relevant step toward efficiency is the choice of the surfactant type and its concentration.

  19. 27 CFR 25.251 - Authorized removals.

    Science.gov (United States)

    2010-04-01

    ..., DEPARTMENT OF THE TREASURY LIQUORS BEER Removal of Brewer's Yeast and Other Articles § 25.251 Authorized removals. (a) Brewer's yeast. A brewer may remove brewer's yeast, in liquid or solid form containing not... including the words “Brewer's Yeast.” (c) Pipeline. If brewer's yeast is removed by pipeline, the......

  20. Support of US CLIVAR Project Office 2012

    Energy Technology Data Exchange (ETDEWEB)

    Cummings, Donna [University Corporation for Atmospheric Research (UCAR), Boulder, CO (United States)

    2013-08-31

    Director of JOSS, supervised the U.S. CLIVAR Project Office Director and helped direct the officer to enhance the goals and objectives of the U.S. CLIVAR Project and budget. Financial Manager of JOSS, worked to complete proposals and monitor compliance with award requirements and funding limitations and ensure the U.S. CLIVAR Project Office complied with UCAR policies and procedures. Project Coordinator administered the funding for the U.S. CLIVAR Project Office and was responsible for coordinating special projects that required additional support from JOSS technical staff. These projects included activities such as website updates, technology upgrades, production of printed reports, and development of graphic elements like logos. Web Developer worked both on web development and graphic work and the work consisted of the following: Maintaining the site ? installing updates to Drupal CMS (Content Management System). Creating new templates for webpages and styling them with CSS and JavaScript/jQuery code. Fixing the styling on webpages that the content contributor/manager (Jenn Mays) created and has had trouble with. Creating new web forms for abstract uploading, subscriptions, and meeting registrations. Created 4 webpages for the ?ASP: Key Uncertainties in the Global Carbon-Cycle? meeting. Developed a document review form, instruction webpages, login redirect, dynamic table with form submissions for the US CLIVAR SSC Science Plan Document Review. This was open to the public from June 12, 2013 until July 10, 2013. During this time the user accounts had to be checked (daily) that were created by the public, to delete any spam ones. Graphics work: preparing images for general use on webpages, webpage banners, and for meeting name badges, creating a US CLIVAR letterhead, redesigning the US AMOC logo. System Administrator spent time working on the migration of the US CLIVAR site from the USGCRP office to UCAR here Boulder. This was done to increase the general speed of

  1. Alzheimer's Project

    Medline Plus

    Full Text Available ... voluntary health organization in Alzheimer's care, support and research, the Alzheimer's Association has been an active partner in "THE ALZHEIMER'S PROJECT," ... (48 minutes) "Momentum ...

  2. Sludge Heel Removal Analysis for Slurry Pumps of Tank 11

    International Nuclear Information System (INIS)

    Computational fluid dynamics methods were used to develop and recommend a slurry pump operational strategy for sludge heel removal in Tank 11. Flow patterns calculated by the model were used to evaluate the performance of various combinations of operating pumps and their orientation. The models focused on removal of the sludge heel located at the edge of Tank 11 using the four existing slurry pumps. The models and calculations were based on prototypic tank geometry and expected normal operating conditions as defined by Tank Closure Project (TCP) Engineering. Computational fluid dynamics models of Tank 11 with different operating conditions were developed using the FLUENT(tm) code. The modeling results were used to assess the efficiency of sludge suspension and removal operations in the 75-ft tank. The models employed a three-dimensional approach, a two-equation turbulence model, and an approximate representation of flow obstructions. The calculated local velocity was used as a measure of sludge removal and mixing capability. For the simulations, a series of the modeling calculations was performed with indexed pump orientations until an efficient flow pattern near the potential location of the sludge mound was established for sludge removal. The calculated results demonstrated that the existing slurry pumps running at 1600 rpm could remove the sludge mound from the tank with a 103 in. liquid level, based on a minimum sludge suspension velocity of 2.27 ft/sec. In this case, the only exception is the region within about 2 ft. from the tank wall. Further results showed that the capabilities of sludge removal were affected by the indexed pump orientation, the number of operating pumps, and the pump speed. A recommended operational strategy for an efficient flow pattern was developed to remove the sludge mound assuming that local fluid velocity can be used as a measure of sludge suspension and removal. Sensitivity results showed that for a given pump speed, a higher tank

  3. Microalgae removal with Moringa oleifera.

    Science.gov (United States)

    Barrado-Moreno, M M; Beltran-Heredia, J; Martín-Gallardo, J

    2016-02-01

    Moringa oleifera seed extract was tested for algae (Chlorella, Microcystis, Oocystis and Scenedesmus) removal by Jar-test technique. This coagulant can be used in drinking water treatment. Jar-test has been carried out in order to evaluate the efficiency of this natural coagulant agent inside real surface water matrix. The influence of variables has been studied in this process, including operating parameters such as coagulant dosage, initial algae concentration, pH, agitation time and water matrix. Removal capacity is verified for water with high contamination of algae while the process is not affected by the pH and water matrix. Coagulation process may be modelling through Langmuir and Freundlich adsorption hypothesis, so acceptable r2 coefficients are obtained.

  4. Microalgae removal with Moringa oleifera.

    Science.gov (United States)

    Barrado-Moreno, M M; Beltran-Heredia, J; Martín-Gallardo, J

    2016-02-01

    Moringa oleifera seed extract was tested for algae (Chlorella, Microcystis, Oocystis and Scenedesmus) removal by Jar-test technique. This coagulant can be used in drinking water treatment. Jar-test has been carried out in order to evaluate the efficiency of this natural coagulant agent inside real surface water matrix. The influence of variables has been studied in this process, including operating parameters such as coagulant dosage, initial algae concentration, pH, agitation time and water matrix. Removal capacity is verified for water with high contamination of algae while the process is not affected by the pH and water matrix. Coagulation process may be modelling through Langmuir and Freundlich adsorption hypothesis, so acceptable r2 coefficients are obtained. PMID:26688055

  5. AdapterRemoval v2

    DEFF Research Database (Denmark)

    Schubert, Mikkel; Lindgreen, Stinus; Orlando, Ludovic Antoine Alexandre

    2016-01-01

    BACKGROUND: As high-throughput sequencing platforms produce longer and longer reads, sequences generated from short inserts, such as those obtained from fossil and degraded material, are increasingly expected to contain adapter sequences. Efficient adapter trimming algorithms are also needed to...... process the growing amount of data generated per sequencing run. FINDINGS: We introduce AdapterRemoval v2, a major revision of AdapterRemoval v1, which introduces (i) striking improvements in throughput, through the use of single instruction, multiple data (SIMD; SSE1 and SSE2) instructions and multi......-threading support, (ii) the ability to handle datasets containing reads or read-pairs with different adapters or adapter pairs, (iii) simultaneous demultiplexing and adapter trimming, (iv) the ability to reconstruct adapter sequences from paired-end reads for poorly documented data sets, and (v) native gzip and...

  6. Removing Barriers to Interdisciplinary Research

    CERN Document Server

    Jacobs, Naomi

    2010-01-01

    A significant amount of high-impact contemporary scientific research occurs where biology, computer science, engineering and chemistry converge. Although programmes have been put in place to support such work, the complex dynamics of interdisciplinarity are still poorly understood. In this paper we interrogate the nature of interdisciplinary research and how we might measure its "success", identify potential barriers to its implementation, and suggest possible mechanisms for removing these impediments.

  7. Thorium removal by different adsorbents

    Energy Technology Data Exchange (ETDEWEB)

    Metaxas, Michail; Kasselouri-Rigopoulou, Vasilia; Galiatsatou, Polymnia; Konstantopoulou, Cathrine; Oikonomou, Dimitrios

    2003-02-28

    The removal of radiotoxic Th{sup 4+} from aqueous solutions has been explored using two different groups of adsorptive materials (e.g. two activated carbons and four zeolites--two natural and two synthetic). The activated carbons were prepared from solvent extracted olive pulp (SEOP) and olive stone (OS) by a two-step physical activation method with steam. They were characterized by N{sub 2} at 77 K adsorption, Hg porosimetry and by determination of their iodine number. All carbons prepared are of the H-type (e.g. contain mainly basic surface oxides) confirmed by the results of the Boehm's method. The natural zeolites, clinoptilolite (NaCLI) and mordenite (NaMOR), were pretreated with Na{sup +} before the adsorption experiments, while the synthetic ones, NaX and NaA, were provided in their commercial sodium form. The natural zeolites, NaCLI and NaMOR, utilized 11.5 and 38.6% of the theoretical ion-exchange capacity, based on Al content, respectively, while NaX and NaA utilized 41.5 and 45.9%, respectively. The activated carbons showed better removal capability than NaCLI. NaMOR, showed comparable results to the carbon originated from OS, but lower removal capability than the carbon originated from SEOP. The synthetic zeolites showed the highest removal ability for thorium ions due to their increased ion-exchange capacity because of their cleaner and larger framework channels and their higher number of ion-exchange sites. The carbons adsorption capacity mainly depends on the content and nature of functional surface groups. The adsorption data were fitted to Langmuir and Freundlich models. The former achieved best fits and was further applied to obtain the respective Langmuir constant and maximum adsorption capacity for each system.

  8. STS-31: APU Controller Removal

    Science.gov (United States)

    1990-01-01

    The launch April 10 of the STS-31 was scrubbed at T-4 minutes due to a faulty valve in auxiliary power unit (APU) number one. The auxiliary power unit is a hydrazine-fueled, turbine-driven power unit that generates mechanical shaft power to drive a hydraulic pump that produces pressure for the orbiter's hydraulic system. This video shows the removal of the STS-31's auxiliary power unit (APU).

  9. Technical Description Lillgrund Wind Power Plant. Lillgrund Pilot Project

    Energy Technology Data Exchange (ETDEWEB)

    Jeppsson, Joakim; Larsen, Poul Erik; Larsson, Aake (Vattenfall Vindkraft AB, Stockholm (Sweden))

    2008-09-15

    Lillgrund offshore wind power plant comprises 48 wind turbines, each rated at 2.3 MW, bringing the total wind farm capacity to 110 MW. The Lillgrund offshore wind power plant is located in a shallow area of Oeresund, 7 km off the coast of Sweden and 7 km south from the Oeresund Bridge connecting Sweden and Denmark. An average wind speed of around 8,5 m/s at hub height, combined with a relatively low water depth of 4 to 8 meters makes it economically feasible to build here. Vattenfall Vindkraft AB is the owner and operator of Lillgrund offshore wind power plant. Lillgrund is a Swedish pilot project supported by the Swedish Energy Agency. The bidding process was completed during 2005 and the offshore power plant was constructed in the period 2006 to 2007. The wind farm was constructed on time and has now been successfully operational since December 2007. There is, however, always potential for improvement and the aim of this report has been to determine and highlight these areas. It is worth noting out that only the electrical system and the foundations are tailor made at offshore wind power plants. The wind turbines are more or less standard products with none or very limited possibilities for project specific design changes. Geotechnical investigations are expensive and it can be difficult to balance the risks as well as the benefits of this expense in the early phases of a large infrastructure project. As a whole, the geotechnical surveys at Lillgrund proved to be useful. They identified potential issues, such as the fact that extra excavation was required for two of the foundations. It also revealed the location of a small number of boulders that would have to be removed. Vattenfall requested a complete study of the electrical system for Lillgrund to be delivered with the bids. That request was not met. Instead Siemens Wind Power began a complete electrical system study after being awarded the Contract. The electrical system study was completed during the

  10. HSAPS market analysis project

    International Nuclear Information System (INIS)

    The H-SAPS (Hydrogen Stand-Alone Power System) project, an EU project within the ALTENER programme in the period 2002-2004, was initiated to determine the potential for the introduction of environmentally benign hydrogen technology in what is believed to be a near-term market, namely stand-alone power systems (SAPS). The objective of the project was to examine the technological, political, social and economical factors affecting the emergence of hydrogen technology in the stand-alone power system market today and in the future. The scope of the project was limited to small and medium sized stand-alone power systems, up to a few hundred kilowatts (kW) power rating and based on renewable energy as the primary energy source. The work was divided into five phases: (1) Inception, (2) Data collection and analysis, (3) Market analysis and barrier removal, (4) Dissemination, and (5) Final report. Separate reports were written on these topics, and later summarised this final report. The H-SAPS-project identified the following critical technical barriers (in prioritized order): (1) High costs of both electrolyser and fuel cell solutions, (2) Short lifetime warranties and little lifetime experience for PEM electrolysers and PEM fuel cells, (3) Low energy efficiency of the hydrogen energy system (critical for small systems), and (4) The need to develop easy-to-use and energy efficient gas and electricity control systems. One of the main conclusions from the project is that there is a need to focus on interim solutions, based on conventional energy technologies (e.g., internal combustion engines instead of fuel cells), in order for H-SAPS to compete in the near-term SAPS-market (author) (ml)

  11. HSAPS market analysis project

    Energy Technology Data Exchange (ETDEWEB)

    Gloeckner, Ronny; Aaberg, Rolf Jarle

    2006-12-15

    The H-SAPS (Hydrogen Stand-Alone Power System) project, an EU project within the ALTENER programme in the period 2002-2004, was initiated to determine the potential for the introduction of environmentally benign hydrogen technology in what is believed to be a near-term market, namely stand-alone power systems (SAPS). The objective of the project was to examine the technological, political, social and economical factors affecting the emergence of hydrogen technology in the stand-alone power system market today and in the future. The scope of the project was limited to small and medium sized stand-alone power systems, up to a few hundred kilowatts (kW) power rating and based on renewable energy as the primary energy source. The work was divided into five phases: (1) Inception, (2) Data collection and analysis, (3) Market analysis and barrier removal, (4) Dissemination, and (5) Final report. Separate reports were written on these topics, and later summarised this final report. The H-SAPS-project identified the following critical technical barriers (in prioritized order): (1) High costs of both electrolyser and fuel cell solutions, (2) Short lifetime warranties and little lifetime experience for PEM electrolysers and PEM fuel cells, (3) Low energy efficiency of the hydrogen energy system (critical for small systems), and (4) The need to develop easy-to-use and energy efficient gas and electricity control systems. One of the main conclusions from the project is that there is a need to focus on interim solutions, based on conventional energy technologies (e.g., internal combustion engines instead of fuel cells), in order for H-SAPS to compete in the near-term SAPS-market (author) (ml)

  12. After-heat removing device

    International Nuclear Information System (INIS)

    Air cooling devices of a plurality of loops are arranged, each of the cooling device comprises a damper and a vane therein, and a heat transfer tube is inserted between the damper and the vane. The minimum limit value for the opening degree of each of the damper and the vane is changed stepwise for each of the loops. After reactor shutdown, the opening degree of the damper and the vane for each of the loops is simultaneously fixed to the minimum opening degree set for each of the loops. Since the amount of inflown air to the loop having the damper and the vane of the maximum opening degree is greater compared with that of other loops, and the amount of heat removal is maximum, coolants in a heat transfer tube portion are frozen in a short period of time and heat removal is impossible. Then, after heat is successively removed by other loops set to smaller opening degree for the damper and the vane. With such procedures, degradation of reliability due to erroneous closure of the damper and the vane can be eliminated with no requirement for an operator's control for the opening degree. (I.N.)

  13. Removal of dabigatran by hemodialysis.

    Science.gov (United States)

    Chang, Don N; Dager, William E; Chin, Andrew I

    2013-03-01

    Dabigatran is a newly available oral direct thrombin inhibitor approved for anticoagulation therapy to prevent strokes in patients with nonvalvular atrial fibrillation. Unlike warfarin, dabigatran's observed therapeutic window and minimal drug-to-drug interaction suggest that invasive laboratory testing and dose adjustment is not necessary. In circumstances of excessive anticoagulation, such as overdoses, decreased kidney function, or instances of significant bleeding, reversing dabigatran's effects may be necessary. Unlike warfarin, no rapid-acting antidote to reverse the effects of dabigatran is known. However, hemodialysis has been suggested as a method of removing dabigatran and thereby reducing its anticoagulant effect. We describe a case in which hemodialysis was used in an attempt to remove dabigatran in a patient with excessive anticoagulation from dabigatran and severe intracranial hemorrhage. Serial dabigatran levels suggested that hemodialysis removed the drug. However, given the large volume of distribution of dabigatran in the terminal phase of elimination, a rebound in drug level was noted. We suggest that a longer duration of therapy or more continuous modality of hemodialysis may be needed in conjunction with the initial hemodialysis treatment of dabigatran coagulopathy. PMID:23219111

  14. First-year dam removal activities in the Elwha River - dam removal, sediment dispersal, and fish relocations

    Science.gov (United States)

    Duda, J. J.; McMillan, J. R.; Moses, R.; McHenry, M.; Pess, G. R.; Brenkman, S.; Peters, R.; Zimmerman, M.; Warrick, J. A.; Curran, C. A.; Magirl, C. S.; Beirne, M.; Rubin, S.

    2012-12-01

    After years of anticipation, volumes of Environmental Impact Statements, unprecedented mitigation projects, and the multifaceted collection of pre-dam removal data, the deconstruction phase of the Elwha River restoration project officially began on September 17th, 2011. With their simultaneous decommissioning, the removal of the 64 m tall Glines Canyon Dam and 33 m tall Elwha Dam represents one of the largest such projects of its kind in North America. The nearly 19 million m3 of sediment residing in the dammed reservoirs is being eroded by the river in one of the largest controlled releases of sediment into a river and marine waters in recorded history. The release of sediment and the halting of deconstruction and reservoir draw down activities during "fish windows" are largely determining a deconstruction schedule expected to last about 2 years. High suspended sediment concentrations, modeled to exceed 10,000 mg/L during the highest flows and to exceed 500 mg/L for 39% of the time in year 4 of the project (15% is the recorded background level entering the upper reservoir), could last for up to 3-5 years following dam removal depending on hydrological conditions. Anadromous fish, including three federally listed species (Puget Sound Chinook salmon, steelhead, and bull trout), reside in the river downstream of the Elwha dam for part of their life cycle. All five species of Pacific salmon and steelhead, either locally extirpated (sockeye) or persisting below the impassable Elwha Dam in degraded spawning and rearing habitat, are expected to recolonize the watershed to degrees that will vary spatially and temporally due to life history characteristics and levels of human intervention. During the first year of dam removal, adult coho salmon and steelhead were relocated from areas of high turbidity downstream of the Elwha Dam site to two tributaries upstream, where some of them successfully spawned. Additionally, steelhead were observed to naturally migrate past the

  15. Predicting the type, location and magnitude of geomorphic responses to dam removal: Role of hydrologic and geomorphic constraints

    Science.gov (United States)

    Gartner, John D.; Magilligan, Francis J.; Renshaw, Carl E.

    2015-12-01

    Using a dam removal on the Ashuelot River in southern New Hampshire, we test how a sudden, spatially non-uniform increase in river slope alters sediment transport dynamics and riparian sediment connectivity. Site conditions were characterized by detailed pre- and post-removal field surveys and high-resolution aerial lidar data, and locations of erosion and deposition were predicted through one-dimensional hydrodynamic modeling. The Homestead Dam was a ~ 200 year old, 4 m high, 50 m wide crib dam that created a 9.5 km long, relatively narrow reservoir. Following removal, an exhumed resistant bed feature of glaciofluvial boulders located 400 m upstream and ~ 2.5 m lower than the crest of the dam imposed a new boundary condition in the drained reservoir, acting as a grade control that maintained a backwater effect upstream. During the 15 months following removal, non-uniform erosion in the former reservoir totaled ~ 60,000 m3 (equivalent to ~ 9.3 cm when averaged across the reservoir). Net deposition of ~ 10,700 m3 was measured downstream of the dam, indicating most sediment from the reservoir was carried more than 8 km downstream beyond the study area. The most pronounced bed erosion occurred where modeled sediment transport increased in the downstream direction, and deposition occurred both within and downstream of the former reservoir where modeled sediment transport decreased in the downstream direction. We thus demonstrate that spatial gradients in sediment transport can be used to predict locations of erosion and deposition on the stream bed. We further observed that bed incision was not a necessary condition for bank erosion in the former reservoir. In this characteristically narrow and shallow reservoir lacking abundant dam-induced sedimentation, the variable resistance of the bed and banks acted as geomorphic constraints. Overall, the response deviated from the common conceptual model of knickpoint erosion and channel widening due to dam removal. With

  16. Alzheimer's Project

    Medline Plus

    Full Text Available ... state Home > News & Events > Upcoming Events > HBO Alzheimer’s Project In the News Walk to End Alzheimer's Upcoming ... Disease Awareness Month World Alzheimer's Month HBO Alzheimer’s Project MAKE A DONATION Your gift will help us ...

  17. PUREX transition project case study

    Energy Technology Data Exchange (ETDEWEB)

    Jasen, W.G.

    1996-04-15

    In December 1992, the US Department of Energy (DOE) directed that the Plutonium-Uranium Extraction (PUREX) Plant be shut down and deactivated because it was no longer needed to support the nation`s production of weapons-grade plutonium. The PUREX/UO{sub 2} Deactivation Project will establish a safe and environmentally secure configuration for the facility and preserve that configuration for 10 years. The 10-year span is used to predict future maintenance requirements and represents the estimated time needed to define, authorize, and initiate the follow-on decontamination and decommissioning activities. Accomplishing the deactivation project involves many activities. Removing major hazards, such as excess chemicals, spent fuel, and residual plutonium are major goals of the project. The scope of the PUREX Transition Project is described within.

  18. Magnetohydrodynamic projects at the CDIF

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    This quarterly technical progress report presents the tasks accomplished at the Component Development and Integration Facility (CDIF) during the second quarter of FY91. Areas of technical progress this quarter included: coal system development; seed system development; test bay modification; channel power dissipation and distribution system development; oxygen system storage upgrade; iron-core magnet thermal protection system checkout; TRW slag rejector/CDIF slag removal project; stack gas/environmental compliance upgrade; coal-fired combustor support; 1A channels fabrication and assembly; support of Mississippi State University diagnostic testing; test operations and results; data analysis and modeling; technical papers; and projected activities. 2 tabs.

  19. Characterization and quantification of deposits build up and removal in straw suspension fired boilers

    DEFF Research Database (Denmark)

    Jensen, Peter Arendt; Shafique Bashir, Muhammad; Wedel, Stig;

    This project deals with ash deposit formation in suspension fired biomass power plant boilers. The project has been conducted in a tight collaboration between Vattenfall and the CHEC Research Centre at DTU Department of Chemical Engineering. A large part of the project has been performed...... by conducting advanced probe measurements at the Amagerværkets Vattenfall owed boilers. It was the objective of the project to provide an improved understanding of ash deposit formation and removal in biomass suspension fired boilers. The project have provided a large amount of knowledge on the following issues......: 1) The influence of local boiler conditions on deposit formation in suspension fired boilers using wood or co-firing straw and wood, 2) quantification of deposit removal in biomass suspension firing boilers with regards both to natural shedding and soot blower induced shedding, 3) established...

  20. Characterization and quantification of deposits build up and removal in straw suspension fired boilers. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Arendt Jensen, Peter; Wedel, S.; Jappe Frandsen, F.; Dam-Johansen, K.; Shafique Bashir, M. [Technical Univ. of Denmark. CHEC Research Centre, Kgs. Lyngby (Denmark); Wadenback, J.; Thaaning Pedersen, S. [Vattenfall A/S, Copenhagen (Denmark)

    2013-07-15

    This project deals with ash deposit formation in suspension fired biomass power plant boilers. The project has been conducted in a tight collaboration between Vattenfall and the CHEC Research Centre at DTU Department of Chemical Engineering. A large part of the project has been performed by conducting advanced probe measurements at the Amagervaerkets Vattenfall owed boilers. It was the objective of the project to provide an improved understanding of ash deposit formation and removal in biomass suspension fired boilers. The project have provided a large amount of knowledge on the following issues: 1) The influence of local boiler conditions on deposit formation in suspension fired boilers using wood or co-firing straw and wood, 2) quantification of deposit removal in biomass suspension firing boilers with regards both to natural shedding and soot blower induced shedding, 3) established relations of the properties of fuel ash, fly ash and deposits, 4) use of coal ash to remedy biomass ash induced boiler deposit problems. (Author)

  1. The Yangtze-Project

    Science.gov (United States)

    Subklew, Günter; Ulrich, Julia; Fürst, Leander; Höltkemeier, Agnes

    2010-05-01

    then encounter considerably improved climatic conditions with higher temperatures during their physiologically active season in the summer months. This reversal of the flood pulse in the course of the year will exert an enormous influence on the fauna and flora and the associated processes. Other parameters resulting from the management of the reservoir are the sediment deposits and their varying extents in the different zones of the WFZ. For example, the different degrees of compaction of the sediment of the river bank will largely determine the exchange of oxygen, nutrients and metabolites between the plants and the water body and thus the major ecosystem functions. The locally different thicknesses of the sediment body will be decisive for the emergence of plant shoots through the sediment. In areas of high flow rates, in contrast, habitats will be established that are strongly characterized by the dynamics of the pebbles and boulders. The Three Gorges Project will thus bring about a significant change in habitat conditions for vegetation in the WFZ whose consequences cannot yet be predicted with any certainty. This also concerns the potential and long-term impacts of changed vegetation on the local population, who exploit the plant resources, and also on tourism and on the hydroregime and the sedimentation regime in the reservoir. Landslides and rock falls are the major geological events in the Three Gorges region. The mud and debris avalanches formed during such landslips represent a danger both for areas of settlement and also for land used industrially and agriculturally, as well as for infrastructure facilities, and may also considerably obstruct navigation. Furthermore, the analogous mass movements are one of the reasons for the silting up of the Yangtze and many of its tributaries. The region of the Three Gorges contains rapidly growing urban centres that will receive further impulses for growth from the dam project. The fact that the Chongqing conurbation

  2. Water Distribution and Removal Model

    International Nuclear Information System (INIS)

    The design of the Yucca Mountain high level radioactive waste repository depends on the performance of the engineered barrier system (EBS). To support the total system performance assessment (TSPA), the Engineered Barrier System Degradation, Flow, and Transport Process Model Report (EBS PMR) is developed to describe the thermal, mechanical, chemical, hydrological, biological, and radionuclide transport processes within the emplacement drifts, which includes the following major analysis/model reports (AMRs): (1) EBS Water Distribution and Removal (WD and R) Model; (2) EBS Physical and Chemical Environment (P and CE) Model; (3) EBS Radionuclide Transport (EBS RNT) Model; and (4) EBS Multiscale Thermohydrologic (TH) Model. Technical information, including data, analyses, models, software, and supporting documents will be provided to defend the applicability of these models for their intended purpose of evaluating the postclosure performance of the Yucca Mountain repository system. The WD and R model ARM is important to the site recommendation. Water distribution and removal represents one component of the overall EBS. Under some conditions, liquid water will seep into emplacement drifts through fractures in the host rock and move generally downward, potentially contacting waste packages. After waste packages are breached by corrosion, some of this seepage water will contact the waste, dissolve or suspend radionuclides, and ultimately carry radionuclides through the EBS to the near-field host rock. Lateral diversion of liquid water within the drift will occur at the inner drift surface, and more significantly from the operation of engineered structures such as drip shields and the outer surface of waste packages. If most of the seepage flux can be diverted laterally and removed from the drifts before contacting the wastes, the release of radionuclides from the EBS can be controlled, resulting in a proportional reduction in dose release at the accessible environment

  3. Water Distribution and Removal Model

    Energy Technology Data Exchange (ETDEWEB)

    Y. Deng; N. Chipman; E.L. Hardin

    2005-08-26

    The design of the Yucca Mountain high level radioactive waste repository depends on the performance of the engineered barrier system (EBS). To support the total system performance assessment (TSPA), the Engineered Barrier System Degradation, Flow, and Transport Process Model Report (EBS PMR) is developed to describe the thermal, mechanical, chemical, hydrological, biological, and radionuclide transport processes within the emplacement drifts, which includes the following major analysis/model reports (AMRs): (1) EBS Water Distribution and Removal (WD&R) Model; (2) EBS Physical and Chemical Environment (P&CE) Model; (3) EBS Radionuclide Transport (EBS RNT) Model; and (4) EBS Multiscale Thermohydrologic (TH) Model. Technical information, including data, analyses, models, software, and supporting documents will be provided to defend the applicability of these models for their intended purpose of evaluating the postclosure performance of the Yucca Mountain repository system. The WD&R model ARM is important to the site recommendation. Water distribution and removal represents one component of the overall EBS. Under some conditions, liquid water will seep into emplacement drifts through fractures in the host rock and move generally downward, potentially contacting waste packages. After waste packages are breached by corrosion, some of this seepage water will contact the waste, dissolve or suspend radionuclides, and ultimately carry radionuclides through the EBS to the near-field host rock. Lateral diversion of liquid water within the drift will occur at the inner drift surface, and more significantly from the operation of engineered structures such as drip shields and the outer surface of waste packages. If most of the seepage flux can be diverted laterally and removed from the drifts before contacting the wastes, the release of radionuclides from the EBS can be controlled, resulting in a proportional reduction in dose release at the accessible environment. The purposes

  4. Freedom Project

    Directory of Open Access Journals (Sweden)

    Alejandra Suarez

    2014-02-01

    Full Text Available Freedom Project trains prisoners in nonviolent communication and meditation. Two complementary studies of its effects are reported in this article. The first study is correlational; we found decreased recidivism rates among prisoners trained by Freedom Project compared with recidivism rates in Washington state. The second study compared trained prisoners with a matched-pair control group and found improvement in self-reported anger, self-compassion, and certain forms of mindfulness among the trained group. Ratings of role-plays simulating difficult interactions show increased social skills among the group trained by Freedom Project than in the matched controls.

  5. TIARA project

    Science.gov (United States)

    Malecki, P.

    2013-10-01

    The aim of the Test Infrastructure and Accelerator Research Area - the TIARA project[1] is to consolidate and support the European R&D program in the field of physics and techniques of particle accelerators. This project, partially funded by the European Commission, groups 11 participants from 8 European countries, including Poland. Its present, threeyear (2011-2013) preparatory phase (PP) is shortly described in this paper. The project is divided into 9 work packages (WP). We will concentrate on four of them dedicated to governance, R&D infrastructures, joint R&D programming, and education and training, in which Polish participants are actively involved.

  6. Enhanced biological phosphorus removal in the wastewater treatment plant of Bunnik

    Energy Technology Data Exchange (ETDEWEB)

    Vries, H.P. de; Rensink, J.H.

    1989-02-01

    At several sewage treatment plants in the Netherlands there has been continuously found a remarkable high phosphorus removal rate, without using chemical additions. In Bunnik this is up to 90%. In the effluent we will mostly find less than 1 mg P/l. At the Bunnik plant we deal with biological excess phosphorus removal. Biological phosphorus removal is based on the luxury uptake of phosphorus by some bacteria. On certain circumstances micro-organisms of the genius Acinetobacter stored excess amounts of phosphates in their cells. In 1984 a project started, financed by the institute for inland waters and wastewater treatment (DBW/RIZA). The purpose of this research project was to find factors which were, responsible for the remarkable enhanced phosphorus removal in the Bunnik plant.

  7. THE REMOVAL OF GLYPHOSATE FROM DRINKING WATER

    Science.gov (United States)

    The effectiveness of granulated activated carbon (GAC), packed activated carbon (PAC), conventional treatment, membranes, and oxidation for removing glyphosate from natural waters is evaluated. Results indicate that GAC and PAC are not effective in removing glyphosate, while oxid...

  8. Photodynamic therapy for hair removal

    Directory of Open Access Journals (Sweden)

    Mohamed H. M. Ali

    2013-05-01

    Full Text Available Background: Unwanted hair is one of the most common medical problems affecting women of reproductive age inducing a lot of psychological stress and threatening their femininity and self-esteem. Old methods of removing unwanted hair include shaving, waxing, chemical depilation, and electrolysis, all of which have temporary results. However laser-assisted hair removal is the most efficient method of long-term hair removal currently available. It is desirable to develop a reduced cost photodynamic therapy (PDT system whose properties should include high efficiency and low side-effects. Method: Mice skin tissues were used in this study and divided into six groups such as controls, free methylene blue (MB incubation, liposome methylene blue (MB incubation, laser without methylene blue (MB, free methylene blue (MB for 3 and 4 hrs and laser, liposome methylene blue (MB for 3 hrs and laser. Methylene blue (MBwas applied to wax epilated areas. The areas were irradiated with CW He-Ne laser system that emits orange-red light with wavelength 632.8 nm and 10 mW at energy density of 5 J/ cm2 for 10 minutes. The UV-visible absorption spectrum was collected by Cary spectrophotometer. Results: Methylene blue (MB is selectively absorbed by actively growing hair follicles due to its cationic property. Methylene blue (MBuntreated sections showed that hair follicle and sebaceous gland are intact and there is no change due to the laser exposure. Free methylene blue (MB sections incubated for 3 hrs showed that He:Ne laser induced destruction in hair follicles, leaving an intact epidermis. Treated section with free methylene blue (MB for 4 hrs showed degeneration and necrosis in hair follicle, leaving an intact epidermis. Liposomal methylene blue (MB sections incubated for 3 hrs showed He:Ne laser induced destruction in hair follicles with intradermal leucocytic infiltration. Conclusions: Low power CW He:Ne laser and methylene blue (MB offered a successful PDT system

  9. Removing oil from produced water

    International Nuclear Information System (INIS)

    This paper reviews the design, operation, and performance of a new gas-assisted clarifier system which acts to remove oil from waste water. The system has no moving parts and uses no chemical additives. The results show that the system can be successfully used to reduce the oil content of waste water to acceptable effluent limits. The systems are designed for offshore oil and gas production facilities. Test results are provided which show the reduction of oil and grease from 211 mg/L to 3 mg/L

  10. Forced removals embodied as tuberculosis.

    Science.gov (United States)

    Richardson, Eugene T; Morrow, Carl D; Ho, Theodore; Fürst, Nicole; Cohelia, Rebekkah; Tram, Khai Hoan; Farmer, Paul E; Wood, Robin

    2016-07-01

    South Africa has one of the worst tuberculosis burdens in the world. Several ecological forces have contributed to this, including high HIV prevalence; failing TB control strategies; crowded, poorly ventilated indoor environments-including the complex web of political and economic interests which produce them; the development of racial capitalism; and mining and migration. In the following study, we measure CO2 levels in public transport to investigate the role extended commutes from peri-urban settlements to urban sites of work-a direct result of forced removals-potentially play in propagating the TB epidemic in Cape Town, South Africa. PMID:27239703

  11. Spikes removal in surface measurement

    International Nuclear Information System (INIS)

    Several cylinder surface topographies made from grey cast iron were measured by Talysurf CCI white light interferometer with and without use of spikes filter. They were plateau honed by abrasive stones. Measured area was 3.3 mm × 3.3 mm, height resolution was 0.01 nm. The forms were eliminated using polynomial of the 3rd degree. After it, spikes were removed using four methods. These approaches were compared. Parameters of the smaller and highest sensitivity on spikes presence were selected

  12. Radioiodine removal in nuclear facilities

    International Nuclear Information System (INIS)

    Technical means are reviewed available for the retention of radioiodine in nuclear power plants and fuel reprocessing plants, its immobilization, storage, and disposal. The removal of iodine species from gaseous effluents of nuclear power plants using impregnated activated charcoal is dealt with. Various scrubbing techniques for trapping iodine from the head-end and dissolver off-gases are discussed as well as solid adsorbents for iodine which may be used to clean up other gaseous streams. Current practices and activities for radioiodine treatment and management in Belgian, Dutch, Swedish, USSR and UK nuclear installations are presented

  13. Dam Removal Information Portal (DRIP)—A map-based resource linking scientific studies and associated geospatial information about dam removals

    Science.gov (United States)

    Duda, Jeffrey J.; Wieferich, Daniel J.; Bristol, R. Sky; Bellmore, J. Ryan; Hutchison, Vivian B.; Vittum, Katherine M.; Craig, Laura; Warrick, Jonathan A.

    2016-08-18

    The removal of dams has recently increased over historical levels due to aging infrastructure, changing societal needs, and modern safety standards rendering some dams obsolete. Where possibilities for river restoration, or improved safety, exceed the benefits of retaining a dam, removal is more often being considered as a viable option. Yet, as this is a relatively new development in the history of river management, science is just beginning to guide our understanding of the physical and ecological implications of dam removal. Ultimately, the “lessons learned” from previous scientific studies on the outcomes dam removal could inform future scientific understanding of ecosystem outcomes, as well as aid in decision-making by stakeholders. We created a database visualization tool, the Dam Removal Information Portal (DRIP), to display map-based, interactive information about the scientific studies associated with dam removals. Serving both as a bibliographic source as well as a link to other existing databases like the National Hydrography Dataset, the derived National Dam Removal Science Database serves as the foundation for a Web-based application that synthesizes the existing scientific studies associated with dam removals. Thus, using the DRIP application, users can explore information about completed dam removal projects (for example, their location, height, and date removed), as well as discover sources and details of associated of scientific studies. As such, DRIP is intended to be a dynamic collection of scientific information related to dams that have been removed in the United States and elsewhere. This report describes the architecture and concepts of this “metaknowledge” database and the DRIP visualization tool.

  14. Endotoxin removal by charge-modified filters.

    OpenAIRE

    Gerba, C P; Hou, K

    1985-01-01

    The effects of positively charged nylon and depth (cellulose-diatomaceous earth) filters on endotoxin removal from various solutions were evaluated. The charged filter media removed significant amounts of Escherichia coli and natural endotoxin from tap water, distilled water, sugars, and NaCl solutions; no significant removal of endotoxin was observed with negatively charged filter media. The extent of removal was influenced by pH, the presence of salts, and organic matter. Such media may be ...

  15. Ultrasound-guided removal of Implanon devices.

    LENUS (Irish Health Repository)

    Persaud, T

    2008-11-01

    Our study has shown that ultrasound-guided localisation and removal of Implanon rods is safe, practical and highly successful. Over a 4-year period, 119 patients had successful, uncomplicated removal of their subdermal devices.The technique is particularly useful for removal of the device when it is not palpable or when an attempt at removal of a palpable device has not been successful.

  16. The Effects of Removable Denture on Swallowing

    OpenAIRE

    Son, Dae-Sik; Seong, Jin Wan; Kim, Younghoon; Chee, Youngjoon; Hwang, Chang Ho

    2013-01-01

    Objective To investigate the relationship between removable dentures and swallowing and describe risks. Methods Twenty-four patients with removable dentures who were referred for videofluoroscopic swallowing study (VFSS) were enrolled. We evaluated the change of swallowing function using VFSS before and after the removal of the removable denture. The masticatory performance by Kazunori's method, sensation of oral cavity by Christian's method, underlying disease, and National Institutes of Hea...

  17. Alzheimer's Project

    Medline Plus

    Full Text Available ... Alzheimer's Gala A Night at Sardi's Alzheimer's Disease Awareness Month World Alzheimer's Month HBO Alzheimer’s ... HBO's "THE ALZHEIMER'S PROJECT" takes a look at the faces behind the disease - and the forces leading us ...

  18. Alzheimer's Project

    Medline Plus

    Full Text Available ... about the films on our message board . Watch films free online now "The Memory Loss Tapes" (85 ... ALZHEIMER'S PROJECT" is a presentation of HBO Documentary Films and the National Institute on Aging at the ...

  19. Alzheimer's Project

    Medline Plus

    Full Text Available ... disease has on those with Alzheimer's and their families. September 14, 2009 "The Alzheimer's Project" wins two ... way Americans thinks about Alzheimer's disease. Tell your family and friends. Post info on your Web site . ...

  20. Alzheimer's Project

    Medline Plus

    Full Text Available ... 272.3900 Find your chapter: search by state Home > News & Events > Upcoming Events > HBO Alzheimer’s Project In the News Walk to End Alzheimer's Upcoming Events AAIC Advocacy Forum Rita ...

  1. Project Reptile!

    Science.gov (United States)

    Diffily, Deborah

    2001-01-01

    Integrating curriculum is important in helping children make connections within and among areas. Presents a class project for kindergarten children which came out of the students' interests and desire to build a reptile exhibit. (ASK)

  2. Alzheimer's Project

    Medline Plus

    Full Text Available ... your family and friends. Post info on your Web site . Become an Alzheimer's champion. Help support vital research and services. "THE ALZHEIMER'S PROJECT" is a presentation of HBO ...

  3. Alzheimer's Project

    Medline Plus

    Full Text Available ... our nation and drive concerned citizens to take action. Here are three ways you can help us change the way ... vital research and services. "THE ALZHEIMER'S PROJECT" is a presentation ...

  4. Alzheimer's Project

    Medline Plus

    Full Text Available ... and the effects this debilitating and fatal disease has on those with Alzheimer's and their families. September ... Alzheimer's care, support and research, the Alzheimer's Association has been an active partner in "THE ALZHEIMER'S PROJECT," ...

  5. Intending Projects

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Project name:Jintan tire production base project (the first-phase project) Construction site:Jintan Economic Development Zone, Jiangsu Province Construction unit:Zhongce Rubber (Jintan) Co., Ltd. Total investment:RMB 2.42 billion yuan Project description:It is planned to cover an area of 3,000 mu. In the first phase, it will cover an area of 520.43 mu with designed staff of 4,500 people. It will mix 150,000 tons of rubber and produce 10 million u- nits of high-performance semi-steel-wire saloon car and light truck radial tires, 500,000 units of OTR tires and 100,000 tons of carbon black per year.

  6. Alzheimer's Project

    Medline Plus

    Full Text Available ... 14, 2009 "The Alzheimer's Project" wins two Creative Arts Emmys Two installments of the multi-part HBO ... from the Alzheimer's Association and others, won Creative Arts Emmy awards. "The Memory Loss Tapes" was honored ...

  7. Radiochemistry Project

    International Nuclear Information System (INIS)

    Researches carried out in the 'Radiochemistry Project' of the Agricultural Nuclear Energy Center, Piracicaba, Sao Paulo State, Brazil, are described. Such researches comprise: dosimetry and radiological protection; development of techniques and methods of chemical analysis and radiochemistry. (M.A.)

  8. Improved Processes to Remove Naphthenic Acids

    Energy Technology Data Exchange (ETDEWEB)

    Aihua Zhang; Qisheng Ma; Kangshi Wang; Yongchun Tang; William A. Goddard

    2005-12-09

    In the past three years, we followed the work plan as we suggested in the proposal and made every efforts to fulfill the project objectives. Based on our large amount of creative and productive work, including both of experimental and theoretic aspects, we received important technical breakthrough on naphthenic acid removal process and obtained deep insight on catalytic decarboxylation chemistry. In detail, we established an integrated methodology to serve for all of the experimental and theoretical work. Our experimental investigation results in discovery of four type effective catalysts to the reaction of decarboxylation of model carboxylic acid compounds. The adsorption experiment revealed the effectiveness of several solid materials to naphthenic acid adsorption and acidity reduction of crude oil, which can be either natural minerals or synthesized materials. The test with crude oil also received promising results, which can be potentially developed into a practical process for oil industry. The theoretical work predicted several possible catalytic decarboxylation mechanisms that would govern the decarboxylation pathways depending on the type of catalysts being used. The calculation for reaction activation energy was in good agreement with our experimental measurements.

  9. Organic micropollutant removal during river bank filtration

    NARCIS (Netherlands)

    Bertelkamp, C.

    2015-01-01

    This study investigated the factors influencing the main removal mechanisms (adsorption and biodegradation) for organic micropollutant (OMP) removal during river bank filtration (RBF) and the possibility of developing a predictive model of this process for OMP removal during RBF. Chapter 2 analysed

  10. System for Removing Pollutants from Incinerator Exhaust

    Science.gov (United States)

    Wickham, David t.; Bahr, James; Dubovik, Rita; Gebhard, Steven C.; Lind, Jeffrey

    2008-01-01

    A system for removing pollutants -- primarily sulfur dioxide and mixed oxides of nitrogen (NOx) -- from incinerator exhaust has been demonstrated. The system is also designed secondarily to remove particles, hydrocarbons, and CO. The system is intended for use in an enclosed environment, for which a prior NOx-and-SO2-removal system designed for industrial settings would not be suitable.

  11. Ultrasonic Abrasive Removal Of EDM Recast

    Science.gov (United States)

    Mandel, Johnny L.; Jacobson, Marlowe S.

    1990-01-01

    Ultrasonic abrasive process removes layer of recast material generated during electrical-discharge machining (EDM) of damper pocket on turbine blade. Form-fitted tool vibrated ultrasonically in damper pocket from which material removed. Vibrations activate abrasive in pocket. Amount of material removed controlled precisely.

  12. Removal and recovery of toxic metal ions from aqueous waste sites using polymer pendant ligands

    Energy Technology Data Exchange (ETDEWEB)

    Fish, D. [Lawrence Berkeley National Lab., CA (United States)

    1996-10-01

    The purpose of this project is to investigate the use of polymer pendant ligand technology to remove and recover toxic metal ions from DOE aqueous waste sites. Polymer pendant lgiands are organic ligands, anchored to crosslinked, modified divinylbenzene-polystyrene beads, that can selectively complex metal ions. The metal ion removal step usually occurs through a complexation or ion exchange phenomena, thus recovery of the metal ions and reuse of the beads is readily accomplished.

  13. Project Management

    DEFF Research Database (Denmark)

    Kampf, Constance

    2009-01-01

    In this video Associate Professor Constance Kampf talks about the importance project management. Not only as a tool in implementation, but also as a way of thinking, and as something that needs to be considered from idea conception......In this video Associate Professor Constance Kampf talks about the importance project management. Not only as a tool in implementation, but also as a way of thinking, and as something that needs to be considered from idea conception...

  14. Trace dispersant detection and removal

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, D.; Volchek, K.; Cathum, S.J.; Peng, H. [SAIC Canada Ltd., Ottawa, ON (Canada); Lane, J. [U.S. Minerals Management Service, Herndon, VA (United States)

    2003-07-01

    A series of tests have been conducted at the OHMSETT facility to determine the performance of different dispersants used to treat oil spills. The testing was complicated by the fact that even trace amounts of dispersants left in the test tank could alter the performance of subsequent dispersants tested in the same test tank. For that reason, an inexpensive membrane based process was developed to remove trace quantities of dispersant from a water source and purify the tank water after each test. Membrane processes have been used to remove surfactants and oil from various types of aqueous streams such as industrial wastewaters, where surfactants and oils can be found in either dissolved or dispersed forms. Several membrane types were tested to determine key operating and separation parameters. The objective was to find a selective membrane with a high flux. Nanofiltration membranes, ultrafiltration membranes, and micro filtration membranes were the three types of membranes considered for this study. Corexit 9500 and Corexit 9527, the two most commonly stocked dispersants in North America, were used to study the relationship between surface tension and dispersant concentration in different solutions. Preliminary results indicate that membrane technology is a viable method to separate surfactants from water. Pilot scale testing was recommended to obtain more accurate estimates and to validate cost estimates. 5 refs., 5 tabs., 9 figs.

  15. Endoscopically removed giant submucosal lipoma

    Directory of Open Access Journals (Sweden)

    Jovanović Ivan

    2007-01-01

    Full Text Available Background. Although uncommon, giant submucosal colon lipomas merit attention as they are often presented with dramatic clinical features such as bleeding, acute bowel obstruction, perforation and sometimes may be mistaken for malignancy. There is a great debate in the literature as to how to treat them. Case report. A patient, 67-year old, was admitted to the Clinic due to a constipation over the last several months, increasing abdominal pain mainly localized in the left lower quadrant accompanied by nausea, vomiting and abdominal distension. Physical examination was unremarkable and the results of the detailed laboratory tests and carcinoembryonic antigen remained within normal limits. Colonoscopy revealed a large 10 cm long, and 4 to 5 cm in diameter, mobile lesion in his sigmoid colon. Conventional endoscopic ultrasound revealed 5 cm hyperechoic lesion of the colonic wall. Twenty MHz mini-probe examination showed that lesion was limited to the submucosa. Since polyp appeared too large for a single transaction, it was removed piecemeal. Once the largest portion of the polyp has been resected, it was relatively easy to place the opened snare loop around portions of the residual polyp. Endoscopic resection was carried out safely without complications. Histological examination revealed the common typical histological features of lipoma elsewhere. The patient remained stable and eventually discharged home. Four weeks later he suffered no recurrent symptoms. Conclusion. Colonic lipomas can be endoscopically removed safely eliminating unnecessary surgery.

  16. Review and comparison of active space debris capturing and removal methods

    Science.gov (United States)

    Shan, Minghe; Guo, Jian; Gill, Eberhard

    2016-01-01

    Space debris is considered as a serious problem for operational space missions. Many enabling space debris capturing and removal methods have been proposed in the past decade and several methods have been tested on ground and/or in parabolic flight experiments. However, not a single space debris has been removed yet. A space debris object is usually non-cooperative and thus different with targets of on-orbit servicing missions. Thus, capturing and removal of space debris is significantly more challenging. One of the greatest challenges is how to reliably capture and remove a non-cooperative target avoiding to generate even more space debris. To motivate this research area and facilitate the development of active space debris removal, this paper provides review and comparison of the existing technologies on active space debris capturing and removal. It also reviews research areas worth investigating under each capturing and removal method. Frameworks of methods for capturing and removing space debris are developed. The advantages and drawbacks of the most relevant capturing and removal methods are addressed as well. In addition, examples and existing projects related to these methods are discussed.

  17. Spacecraft Water Regeneration by Catalytic Wet Air Oxidation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this project is to develop advanced catalysts for a volatile removal assembly used to purify spacecraft water. The innovation of the proposed...

  18. The DR-2 project

    Energy Technology Data Exchange (ETDEWEB)

    Oelgaard, P.L

    2003-06-01

    DR-2 was a 5 MW tank type, water moderated and cooled research reactor, which was operated at the Risoe National Laboratory from 1959 to 1975. After the close-down in1975 the DR-2 has been kept in safe enclosure until now. The aim of the DR-2 project reported here was to characterize the present state of the reactor and to determine, which radionuclides remain where in the reactor in what amounts. The first part of the reactor to be investigated was the reactor tank. The lids at the reactor top were removed, air samples taken and smear test made in the tank. Then the control rods, the magnet rods and other active components were removed from the tank, measured, cut up, and disposed of in waste drums. The beryllium reflector elements were stored in specially prepared containers. When all movable parts had been taken out, the remaining radiation field was measured by use of thermoluminescence dosimeters. Next the hold-up tank room and the concrete cave (the igloo) in front of the thermal column were opened. They had been used as storage rooms for various components and all movable components were removed, measured and, if active, cut into waste drums. Only large and active objects remain stored in the igloo and the hold-up tank room. A number of graphite stringers were taken out of the thermal column and their activity measured. It was a surprise to find, that the stringers contained significant 152Eu and 154Eu activity. Some of the beam plugs and irradiation tubes were extracted and reinserted after their activity had been measured. The activity of the radiation shield of the reactor was measured in three different ways: By drilling two cored holes through the shield, by thermo-luminescence dosimeter measurements in vertical tubes in the concrete shield and by measurements through an open beam hole. At the start of the project the activity in DR-2 was about 45-50 GBq. Now it is about 5-10 GBq. Based on the results of the DR-2 project it is believed that the reactor

  19. Influence of groundwater composition on subsurface iron and arsenic removal.

    Science.gov (United States)

    Moed, D H; van Halem, D; Verberk, J Q J C; Amy, G L; van Dijk, J C

    2012-01-01

    Subsurface arsenic and iron removal (SAR/SIR) is a novel technology to remove arsenic, iron and other groundwater components by using the subsoil. This research project investigated the influence of the groundwater composition on subsurface treatment. In anoxic sand column experiments, with synthetic groundwater and virgin sand, it was found that several dissolved substances in groundwater compete for adsorption sites with arsenic and iron. The presence of 0.01 mmol L(-1) phosphate, 0.2 mmol L(-1) silicate, and 1 mmol L(-1) nitrate greatly reduced the efficiency of SAR, illustrating the vulnerability of this technology in diverse geochemical settings. SIR was not as sensitive to other inorganic groundwater compounds, though iron retardation was limited by 1.2 mmol L(-1) calcium and 0.06 mmol L(-1) manganese. PMID:22678215

  20. Influence of groundwater composition on subsurface iron and arsenic removal

    KAUST Repository

    Moed, David H.

    2012-06-01

    Subsurface arsenic and iron removal (SAR/SIR) is a novel technology to remove arsenic, iron and other groundwater components by using the subsoil. This research project investigated the influence of the groundwater composition on subsurface treatment. In anoxic sand column experiments, with synthetic groundwater and virgin sand, it was found that several dissolved substances in groundwater compete for adsorption sites with arsenic and iron. The presence of 0.01 mmol L -1phosphate, 0.2 mmol L -1 silicate, and 1 mmol L -1 nitrate greatly reduced the efficiency of SAR, illustrating the vulnerability of this technology in diverse geochemical settings. SIR was not as sensitive to other inorganic groundwater compounds, though iron retardation was limited by 1.2 mmol L -1 calcium and 0.06 mmol L -1 manganese. © IWA Publishing 2012.

  1. Enhanced biological phosphorus removal - results of experiences in three large waste water treatment plants

    International Nuclear Information System (INIS)

    Within a scientific project especially the operation of four real-size sewage treatment plants with different processes of enhanced biological phosphorus removal is investigated under the aspect of efficiency, stability, practicability and costs of the enhanced biological phosphorus removal. Three plants and first results are explained and compared as well with one another as with data, which are generally regarded as favourable conditions for the enhanced biological phosphorus removal. Between the plants there are significant differences in the degree of P-elimination mainly due to different characteristics of the wastewater. An important influence on P-effluent concentrations may be exacted by P-resolution in the final clarifier. (orig.)

  2. Removing Noise From Pyrosequenced Amplicons

    Directory of Open Access Journals (Sweden)

    Davenport Russell J

    2011-01-01

    Full Text Available Abstract Background In many environmental genomics applications a homologous region of DNA from a diverse sample is first amplified by PCR and then sequenced. The next generation sequencing technology, 454 pyrosequencing, has allowed much larger read numbers from PCR amplicons than ever before. This has revolutionised the study of microbial diversity as it is now possible to sequence a substantial fraction of the 16S rRNA genes in a community. However, there is a growing realisation that because of the large read numbers and the lack of consensus sequences it is vital to distinguish noise from true sequence diversity in this data. Otherwise this leads to inflated estimates of the number of types or operational taxonomic units (OTUs present. Three sources of error are important: sequencing error, PCR single base substitutions and PCR chimeras. We present AmpliconNoise, a development of the PyroNoise algorithm that is capable of separately removing 454 sequencing errors and PCR single base errors. We also introduce a novel chimera removal program, Perseus, that exploits the sequence abundances associated with pyrosequencing data. We use data sets where samples of known diversity have been amplified and sequenced to quantify the effect of each of the sources of error on OTU inflation and to validate these algorithms. Results AmpliconNoise outperforms alternative algorithms substantially reducing per base error rates for both the GS FLX and latest Titanium protocol. All three sources of error lead to inflation of diversity estimates. In particular, chimera formation has a hitherto unrealised importance which varies according to amplification protocol. We show that AmpliconNoise allows accurate estimates of OTU number. Just as importantly AmpliconNoise generates the right OTUs even at low sequence differences. We demonstrate that Perseus has very high sensitivity, able to find 99% of chimeras, which is critical when these are present at high

  3. Removing Cycles in Esterel Programs

    Directory of Open Access Journals (Sweden)

    Reinhard von Hanxleden

    2007-05-01

    Full Text Available Esterel belongs to the family of synchronous programming languages, which are affected by cyclic signal dependencies. This prohibits a static scheduling, limiting the choice of available compilation techniques for programs with such cycles. This work proposes an algorithm that, given a constructive synchronous Esterel program, performs a semantics-preserving source code level transformation that removes cyclic signal dependencies. The transformation is divided into two parts: detection of cycles and iterative resolution of these cycles. It is based on the replacement of cycle signals by a signal expression involving no other cycle signals, thereby breaking the cycle. This transformation of cyclic Esterel programs enables the use of efficient compilation techniques, which are only available for acyclic programs. Furthermore, experiments indicate that the code transformation can even improve code quality produced by compilers that can already handle cyclic programs.

  4. Malware Detection and Removal Techniques

    Directory of Open Access Journals (Sweden)

    Sudhakar Singh

    2013-01-01

    Full Text Available Malwares are malignant softwares. It is designed to damage computer systems without the knowledge of the owner using the system. Softwares from reputable vendors also contain malicious code that affects the system or leaks informations to remote servers. Malwares includes computer viruses, Worms, spyware, dishonest ad-ware, rootkits, Trojans, dialers etc. Malware is one of the most serious security threats on the Internet today. In fact, most Internet problems such as spam e-mails and denial of service attacks have malwareas their underlying cause. Computers that are compromised with malware are often networked together to form botnets and many attacks are launched using these malicious, attacker controlled networks. The paper focuses on various Malware detection and removal methods.

  5. Method of removing radioactive waste

    International Nuclear Information System (INIS)

    A paste prepared by mixing a mixed acid containing HF and at least one of HCl and HNO3 with a paste aid is coated at the surface of radioactive wastes, to dissolve the surface thereof. Water is jetted to remove the dissolved radioactive contaminants and the pastes from the surface of the radioactive wastes. Since the pastes are thus used, the amount of liquid wastes can be remarkably reduced compared with that in a conventional electrolysis method. Further, if it is confirmed that dose rate of the radioactive wastes after decontamination is lower than a predetermined level by adding a step of measuring the extent of contamination of the wastes before and after the steps, they can be handled hereinafter being regarded as ordinary wastes. (T.M.)

  6. Design and Development of a Landmines Removal Robot

    Directory of Open Access Journals (Sweden)

    K.T.M.U. Hemapala

    2012-03-01

    The solution to the demining problem shall be a low cost robotic outfit with resort to nearby available resources and competences (e.g., drawn from the local agricultural machinery and know‐how. This paper discusses an ongoing project that aims to develop a low‐cost robot with intelligent remote‐command abilities, as a cheap productivity upgrading, assembled from standard farming devices, through the shared know‐how and commitment of locally involved operators. During the study, the authors have developed a low‐cost robot capable of removing mines. The robot consists of modified agricultural components including its mobile carrier and the mine effector.

  7. The Maralinga rehabilitation project

    International Nuclear Information System (INIS)

    The $108 million Maralinga Rehabilitation Project to clean-up the former British atomic test site in South Australia, the largest remediation of this type, was completed in 2000. The rehabilitation was agreed by the Commonwealth and South Australian Governments and the Maralinga Tjarujta traditional owners, following methods identified by technical experts. The rehabilitation permits unrestricted access to about 90% of the former restricted area, but excludes full time occupation of the remaining 120 square kilometers. The clean-up has largely been directed at remediating plutonium contamination caused by minor trials. The clean-up involved two components, the removal of surface soil from the more contaminated areas, and the treatment of contaminated debris pits. Over 350,000 cubic meters of soil and debris was removed over about 2 square kilometers of land, and was buried in 10-15 meter deep trenches under a capping of clean soil of at least 5 meters. Treatment of contaminated pit debris at various sites has involved in situ vitrification, a process which involves application of an electric current to heat and melt debris encasing the contaminated material in a vitric/ceramic block, and exhumation of the contaminated debris and at depths of at least 5 meters. The independent regulator to the project, the Australian Radiation Protection and Nuclear Safety Agency, has indicated that the clean-up of the test sites has met the radiological criteria laid down in the original plan. Discussions are progressing with the South Australian Government and the Maralinga Tjarujta traditional owners as to the long-term management of the site, and the possible hand back of the land from the Commonwealth to South Australia for addition to the Maralinga Tjarutja freehold lands. Copyright (2001) Material Research Society

  8. Hot Spot Removal System: System description

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    Hazardous wastes contaminated with radionuclides, chemicals, and explosives exist across the Department of Energy complex and need to be remediated due to environmental concerns. Currently, an opportunity is being developed to dramatically reduce remediation costs and to assist in the acceleration of schedules associated with these wastes by deploying a Hot Spot Removal System. Removing the hot spot from the waste site will remove risk driver(s) and enable another, more cost effective process/option/remedial alternative (i.e., capping) to be applied to the remainder of the site. The Hot Spot Removal System consists of a suite of technologies that will be utilized to locate and remove source terms. Components of the system can also be used in a variety of other cleanup activities. This Hot Spot Removal System Description document presents technologies that were considered for possible inclusion in the Hot Spot Removal System, technologies made available to the Hot Spot Removal System, industrial interest in the Hot Spot Removal System`s subsystems, the schedule required for the Hot Spot Removal System, the evaluation of the relevant technologies, and the recommendations for equipment and technologies as stated in the Plan section.

  9. Electrokinetic removal of heavy metals from soil

    Directory of Open Access Journals (Sweden)

    Puvvadi Venkata Sivapullaiah

    2015-03-01

    Full Text Available Removal of heavy metal ions from soils by electrokinetic treatment has several advantages. The extent of removal, however, is both soil specific and ion specific. The conditions to be maintained have to be established based on laboratory studies. With a view to maximize the removal of metal ions the trends of removal of heavy metal ions such as iron, nickel and cadmium form a natural Indian kaolinitic red earth during different conditions maintained in the electrokinetic extraction process are studied. A laboratory electrokinetic extraction apparatus was assembled for this purpose. Attempts are also made to elucidate the mechanism of removal of the metal ions from soil. The composition of the flushing fluid, voltage and duration of extraction are varied. While dilute acetic acid has been used to neutralize the alkalinity that develops at the cathode, EDTA solution has been used to desorb heavy metals from clay surface. Generally the extent of removal was proportional to the osmotic flow. Nickel and Cadmium are more effectively removed than iron. The percentage removal of Ni is generally proportional to the osmotic flow but shows sensitivity to the pH of the system. There is an optimum voltage for removal of metal ions from soil. The removal of iron was negligible under different conditions studied.

  10. Hot Spot Removal System: System description

    International Nuclear Information System (INIS)

    Hazardous wastes contaminated with radionuclides, chemicals, and explosives exist across the Department of Energy complex and need to be remediated due to environmental concerns. Currently, an opportunity is being developed to dramatically reduce remediation costs and to assist in the acceleration of schedules associated with these wastes by deploying a Hot Spot Removal System. Removing the hot spot from the waste site will remove risk driver(s) and enable another, more cost effective process/option/remedial alternative (i.e., capping) to be applied to the remainder of the site. The Hot Spot Removal System consists of a suite of technologies that will be utilized to locate and remove source terms. Components of the system can also be used in a variety of other cleanup activities. This Hot Spot Removal System Description document presents technologies that were considered for possible inclusion in the Hot Spot Removal System, technologies made available to the Hot Spot Removal System, industrial interest in the Hot Spot Removal System''s subsystems, the schedule required for the Hot Spot Removal System, the evaluation of the relevant technologies, and the recommendations for equipment and technologies as stated in the Plan section

  11. Development of Technology for Effective Removal of Arsenic and Cyanides from Drinking Water and Wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Jo, Jae

    2008-02-09

    The purpose of the project was to perform a joint research and development effort focused upon the development of methods and the prototype facility for effective removal of arsenic and cyanides from drinking water and wastewater, based on the UPEC patented technology. The goals of this project were to validate UPEC technology, to manufacture a prototype facility meeting the market requirements, and to introduce it to both industry and municipalities which deal with the water quality. The project involved design and fabrication of one experimental unit and one prototypical industrial unit, and tests at industrial and mining sites. The project used sodium ferrate (Na2FeO4) as the media to remove arsenic in drinking water and convert arsenic into non-hazardous form. The work consisted of distinct phases ending with specific deliverables in development, design, fabrication and testing of prototype systems and eventually producing validation data to support commercial introduction of technology and its successful implementation.

  12. Solar Imagery - Composites - Full Sun Drawings - Boulder

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Synoptic Analysis Drawings, also known as Neutral Line (NL) drawings, are produced each day by space weather forecaster at the NOAA National Weather Service (NWS)...

  13. Project Reconstruct.

    Science.gov (United States)

    Helisek, Harriet; Pratt, Donald

    1994-01-01

    Presents a project in which students monitor their use of trash, input and analyze information via a database and computerized graphs, and "reconstruct" extinct or endangered animals from recyclable materials. The activity was done with second-grade students over a period of three to four weeks. (PR)

  14. Alzheimer's Project

    Medline Plus

    Full Text Available ... 2" (70 minutes) Be a part of something big. HBO's "THE ALZHEIMER'S PROJECT" will expose the Alzheimer's ... show(); jQuery('#TRByZip').html(teamRaisersListHTML); teamRaisersListHTML = ''; } } else { if (data && data.getTeamraisersResponse) { var teamraisers = luminateExtend.utils.ensureArray(data. ...

  15. Project Narrative

    Energy Technology Data Exchange (ETDEWEB)

    Driscoll, Mary C. [St. Bonaventure University, St Bonaventure, NY(United States)

    2012-07-12

    The Project Narrative describes how the funds from the DOE grant were used to purchase equipment for the biology, chemistry, physics and mathematics departments. The Narrative also describes how the equipment is being used. There is also a list of the positive outcomes as a result of having the equipment that was purchased with the DOE grant.

  16. Project Avatar

    DEFF Research Database (Denmark)

    Juhlin, Jonas Alastair

    'Project Avatar' tager udgangspunkt i den efterretningsdisciplin, der kaldes Open Source Intelligence og indebærer al den information, som ligger frit tilgængeligt i åbne kilder. Med udbredelsen af sociale medier åbners der op for helt nye typer af informationskilder. Spørgsmålet er; hvor nyttig er...

  17. Project Baltia

    Index Scriptorium Estoniae

    2007-01-01

    Uus arhitektuuriajakiri "Project Baltia" tutvustab Baltimaade, Soome ja Peterburi regiooni arhitektuuri, linnaehitust ja disaini. Ilmub neli korda aastas inglise- ja venekeelsena. Väljaandja: kirjastus Balticum Peterburis koostöös Amsterdami ja Moskva kirjastusega A-Fond. Peatoimetaja Vladimir Frolov

  18. Alzheimer's Project

    Medline Plus

    Full Text Available ... Chicago National Alzheimer's Gala A Night at Sardi's Alzheimer's Disease Awareness Month World Alzheimer's Month HBO Alzheimer’s Project ... help us change the way Americans thinks about Alzheimer's disease. Tell your family and friends. Post info on ...

  19. Alzheimer's Project

    Medline Plus

    Full Text Available ... Alzheimer's Gala A Night at Sardi's Alzheimer's Disease Awareness Month World Alzheimer's Month HBO Alzheimer’s Project MAKE ... for kids Learn how Maria Shriver is raising awareness '; jQuery('#luminateApi').hide(); jQuery('#otherLinks').show(); jQuery('#TRByZip'). ...

  20. PACTEL OECD project planning (PACO). PACTEL OECD project planning

    International Nuclear Information System (INIS)

    OECD launched the SETH project to investigate issues relevant for accident prevention and management and to ensure the existence of integral thermal hydraulic test facilities. The facilities included in the SETH project are PKL from Germany and PANDA from Switzerland. At the early stages of the SETH project an idea was raised to exploit the PACTEL facility in a similar OECD project. Without any external funding the analytical work in the required extent would not be possible within Lappeenranta University of Technology, the party responsible of operating PACTEL. This fact directed the PACO project proposal to be conducted for the SAFIR programme. The aim of the PACO project is to prepare a project proposal to OECD of a PACTEL related project. To attain this objective some preliminary analyses have to be performed to ensure the relevancy of the proposed topic. The low power situation, i.e. midloop state was chosen to be the topic in the PACO studies and project planning basis. The plan is to use PACTEL to examine vertical steam generator behaviour during the midloop operation and the following loss of residual heat removal system transient. Such a possibility is acknowledged with special alterations to PACTEL. The APROS code version 5.04.07 was selected as a tool for the preanalyses. The virtual simulation of the chosen experimental situation would give a preconception on the phenomena to be expected and the progression of the transient. Originally the PACO project was planned to continue only for a few months, ending up with the project proposal to OECD during the summer time 2004. During the pre-calculation process it became obvious that the time expected was not enough to establish good pre-calculation results. The reasons for this relates to time used to learn and adapt the use of the chosen code, improvements and corrections in modelling as well as the code ability to manage the special conditions defined for the project topic. Another aspect on completing a

  1. Carbon dioxide removal with inorganic membranes

    Energy Technology Data Exchange (ETDEWEB)

    Judkins, R.R.; Fain, D.E. [Oak Ridge National Laboratory, TN (United States)

    1993-12-31

    The increasing concentrations of greenhouse gases, particularly carbon dioxide, in the atmosphere has sparked a great deal of interest in the removal of CO{sub 2} from flue gases of fossil fueled plants. Presently, several techniques for the removal of CO{sub 2} are considered to have potential, but are lacking in practicality. For example, amine scrubbing of flue gas streams is potential, but are lacking in practically. For example, amine scrubbing of flue gas streams is effective in removing CO{sub 2}, but costs are high; efficiency suffers; and other acid gases must be removed prior to amine stripping. Membrane systems for CO{sub 2} removal are held in high regard, and inorganic, particularly ceramic, membranes offer the potential for high temperature, thus energy saving, removal.

  2. TMI-2 reactor vessel head removal

    International Nuclear Information System (INIS)

    This report describes the safe removal and storage of the Three Mile Island Unit 2 (TMI-2) reactor vessel head. The head was removed in July 1984 to permit the removal of the plenum and the reactor core, which were damaged during the 1979 accident. From July 1982, plans and preparations were made using a standard head removal procedure modified by the necessary precautions and changes to account for conditions caused by the accident. After data acquisition, equipment and structure modifications, and training, the head was safely removed and stored; and the internals indexing fixture and a work platform were installed on top of the vessel. Dose rates during and after the operation were lower than expected; lessons were learned from the operation which will be applied to the continuing fuel removal operations activities

  3. TMI-2 reactor vessel head removal

    International Nuclear Information System (INIS)

    This report describes the safe removal and storage of the Three Mile Island Unit 2 reactor vessel head. The head was removed in July 1984 to permit the removal of the plenum and the reactor core, which were damaged during the 1979 accident. From July 1982, plans and preparations were made using a standard head removal procedure modified by the necessary precautions and changes to account for conditions caused by the accident. After data acquisition, equipment and structure modifications, and training the head was safely removed and stored and the internals indexing fixture and a work platform were installed on top of the vessel. Dose rates during and after the operation were lower than expected; lessons were learned from the operation which will be applied to the continuing fuel removal operations activities

  4. Projective geometry and projective metrics

    CERN Document Server

    Busemann, Herbert

    2005-01-01

    The basic results and methods of projective and non-Euclidean geometry are indispensable for the geometer, and this book--different in content, methods, and point of view from traditional texts--attempts to emphasize that fact. Results of special theorems are discussed in detail only when they are needed to develop a feeling for the subject or when they illustrate a general method. On the other hand, an unusual amount of space is devoted to the discussion of the fundamental concepts of distance, motion, area, and perpendicularity.Topics include the projective plane, polarities and conic sectio

  5. Improving Software Engineering on NASA Projects

    Science.gov (United States)

    Crumbley, Tim; Kelly, John C.

    2010-01-01

    Software Engineering Initiative: Reduces risk of software failure -Increases mission safety. More predictable software cost estimates and delivery schedules. Smarter buyer of contracted out software. More defects found and removed earlier. Reduces duplication of efforts between projects. Increases ability to meet the challenges of evolving software technology.

  6. SELECTIVE CATALYTIC REDUCTION MERCURY FIELD SAMPLING PROJECT

    Science.gov (United States)

    A lack of data still exists as to the effect of selective catalytic reduction (SCR), selective noncatalytic reduction (SNCR), and flue gas conditioning on the speciation and removal of mercury (Hg) at power plants. This project investigates the impact that SCR, SNCR, and flue gas...

  7. Environmental Remediation: Removal of polycyclic aromatic hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Nkansah, Marian Asantewah

    2012-11-15

    Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous persistent semi-volatile organic compounds. They are contaminants that are resistant to degradation and can remain in the environment for long periods due to their high degree of conjugation, and aromaticity. PAHs are present in industrial effluents as products of incomplete combustion processes of organic compounds. Petroleum, coal and shale oil contain extremely complex mixtures of these PAHs, and their transport and refining process can also result in the release of PAHs. It is therefore prudent that such effluents are treated before discharge into the environment. In this project, different approaches to the treatment of PAHs have been investigated. Hydrous pyrolysis has been explored as a potential technique for degrading PAHs in water using anthracene as a model compound. The experiments were performed under different conditions of temperature, substrate, redox systems and durations. The conditions include oxidising systems comprising pure water, hydrogen peroxide and Nafion-SiO2 solid catalyst in water; and reducing systems of formic acid and formic acid / Nafion-SiO2 / Pd-C catalysts to assess a range of reactivities. Products observed in GCMS analysis of the extract from the water phase include anthrone, anthraquinone, xanthone and multiple hydro-anthracene derivatives (Paper I). In addition a modified version of the Nafion-SiO2 solid catalyst in water oxidising system was tested; and reducing systems of formic acid and formic acid / Nafion-SiO2 / Pd-C catalysts were adopted for the conversion of a mixture of anthracene, fluorene and fluoranthene. The rate of conversion in the mixture was high as compared to that of only anthracene (Paper II). Also the use of LECA (Lightweight expanded clay aggregates) as an adsorbent (Paper III) for PAHs (phenanthrene, fluoranthene and pyrene) removal from water has been.(Author)

  8. HAPs-Rx: Precombustion Removal of Hazardous Air Pollutant Precursors

    Energy Technology Data Exchange (ETDEWEB)

    David J. Akers; Clifford E. Raleigh

    1998-03-16

    CQ Inc. and its project team members--Howard University, PrepTech Inc., Fossil Fuel Sciences, the United States Geological Survey (USGS), and industry advisors--are applying mature coal cleaning and scientific principles to the new purpose of removing potentially hazardous air pollutants from coal. The team uniquely combines mineral processing, chemical engineering, and geochemical expertise. This project meets more than 11 goals of the U.S. Department of Energy (DOE), the National Energy Strategy, and the 1993 Climate Change Action Plan. During this project: (1) Equations were developed to predict the concentration of trace elements in as-mined and cleaned coals. These equations, which address both conventional and advanced cleaning processes, can be used to increase the removal of hazardous air pollutant precursors (HAPs) by existing cleaning plants and to improve the design of new cleaning plants. (2) A promising chemical method of removing mercury and other HAPs was developed. At bench-scale, mercury reductions of over 50 percent were achieved on coal that had already been cleaned by froth flotation. The processing cost of this technology is projected to be less than $3.00 per ton ($3.30 per tonne). (3) Projections were made of the average trace element concentration in cleaning plant solid waste streams from individual states. Average concentrations were found to be highly variable. (4) A significantly improved understanding of how trace elements occur in coal was gained, primarily through work at the USGS during the first systematic development of semiquantitative data for mode of occurrence. In addition, significant improvement was made in the laboratory protocol for mode of occurrence determination. (5) Team members developed a high-quality trace element washability database. For example, the poorest mass balance closure for the uncrushed size and washability data for mercury on all four coals is 8.44 percent and the best is 0.46 percent. This indicates an

  9. Characterization of Atmospheric Pressure Plasma Torch and the Surface Interaction for Material Removal

    Science.gov (United States)

    McWilliams, Anthony Joseph

    An atmospheric pressure plasma torch has been developed and characterized for removal of organic based coatings. The focus of the Strategic Environmental Research & Development Program (SERDP) project WP-1762, that funded the bulk of this dissertation work, is removal of paint from US Navy vessels. The goal is to develop a novel technology for coating removal that is capable of reducing the amount of environmental waste produced during the commonly used grit blasting process. The atmospheric pressure air plasma torch was identified as having the capacity to remove the paint systems while using only compressed air and electricity as a media-less removal system with drastically reduced waste generation. Any improvements to the existing technology need to be based on scientific knowledge and thus the plasma removal mechanisms or material warranted investigation. The removal of material does not show a strong relation to the plasma parameters of power, frequency, and gas flow, nor is there a strong relation to the presences of inorganic fillers impeding or altering the removal rates. The underlying removal mechanisms also do not show a strong correlation to the rotational temperature of the plasma but do show a strong correlation to the optical emission intensity. Primarily, the emission from atomic oxygen and molecular nitrogen were identified significant contributors and were investigated further. The plasma feed gas was then varied from the nitrogen and oxygen ratio present in ambient air to pure nitrogen to identify the effect of oxygen on the removal mechanism. From these experiments it was concluded that the oxygen present in air does contribute to the overall removal mechanism; however, it is not the sole contributing factor with the other major factor being nitrogen.

  10. Candidal Leukoplakia on Patient with Removable Denture

    OpenAIRE

    Shiril Paskalis; Anandina Irmagita

    2013-01-01

    Candida infection is a common problem in patients using removable dentures, with the most frequent type is denture stomatitis. But other type of candidal infection could also happen in these patients, such as candidal leukoplakia. We reported a 61 years old female patient who complained a painful lesion under her lower removable denture. Oral examination revealed white plaque that could not be rubbed over an ulcer on the lingual part of alveolar processes under the lower removable denture pla...

  11. Prosthetic stomatitis with removable dentures

    Directory of Open Access Journals (Sweden)

    Rozalieva Yu.Yu.

    2012-06-01

    Full Text Available The Research Objective: To study patients with prosthetic stomatitis, who use the removable laminar dentures. Materials: The consultations and treatment of 79 patients aged 47-65 years have been conducted. The patients have been divided into two clinical groups. The first clinical group (39 persons with the performance of immediate prosthet-ics; the second control clinical group (40 persons — the permanent dentures were produced without the preliminary instruction. Results: All the patients, having the laminar dentures without the preliminary use of immediate constructions of dentures, in spite of repeated correction of them, have had changes of dentures and transitory fold. Patients have been exposed to prosthetic stomatitis of different etiology (without trauma; the single-shot or multiple correction of dentures by the method of rebasing with using of cold cure plastics has been made. Conclusion: Structural and functional changes of dentition during the prosthetic stomatitis lead to disorders, associated by the mucositis. Use of the term of «prosthetic stomatitis» reflects etiological and pathogenetic component of changes in the denture-supporting tissues

  12. Removal of hexafluoroarsenate from waters.

    Science.gov (United States)

    Daus, Birgit; von Tümpling, Wolf; Wennrich, Rainer; Weiss, Holger

    2007-06-01

    Arsenic predominantly occurs in natural ground and surface waters as arsenate and arsenite. Other arsenic species can also be present in anthropogenically influenced waters. By means of a newly-developed speciation technique an arsenic compound was identified as hexafluoroarsenate at high concentration (about 0.8mgl(-1) as As) in a lake polluted by waste water from a former crystal glass factory. This compound shows a completely different behavior than common arsenite and arsenate in waters. However, respective literature data were little found regarding its environmental behavior as well as the applicable remediation technologies. Conventional arsenic treatment mechanisms, such as the well-known sorption to iron hydroxides, can not be used to remediate water with this compound. Hence, an effective method to remove hexafluoroarsenate from water was developed using its strong affinity to anion exchangers (strong basic exchangers with quaternary ammonium groups). The sorption can be described by a Langmuir isotherm and first-order kinetics with a half-life of about 10min. Interferences by sulphate and fluoride, present at much higher concentrations in the polluted lake water, might be expected due to the anion exchange mechanism, but were shown to be of minor importance.

  13. Livestock wastewater treatment: ammonia removal

    International Nuclear Information System (INIS)

    Livestock wastewater contains high concentration of ammonia. Removal of this inorganic species of nitrogen could be achieved through nitrification and de-nitrification. Nitrification process was conducted in the laboratory using activated sludge process with HRT of three and five days. After wastewater undergone nitrification process at Livestock Wastewater Treatment Plant the concentration of influent for N-NH4+ reduced from 400 mg/l to 0 mg/l and concentration of N-NO3- increased from 11 mg/l to 300 mg/l. Nitrification using lab-scale activated sludge process also recorded similar result. Concentration of N-NH4+ reduced from 400 mg/l to 2 mg/l and 380 mg/l to 1.1 mg/l for HRT=5 days and HRT=3 days respectively. N-NO3- was increased from 11 mg/l to 398 mg/l and 14 mg/l to 394 mg/l for HRT=5 days and HRT=3 days, respectively. However changes of N-NH4+ and N=NO3- were not observed using gamma irradiation. The combination of gamma irradiation with activated sludge process indicated difference and its contribution is still investigated

  14. IMPROVED MLV FILTER TO REMOVE MULTIPLICATIVE NOISE

    Institute of Scientific and Technical Information of China (English)

    Li Weibin; Liu Fang; Jiao Licheng; Zhang Shuling; Li Zongling

    2006-01-01

    More methods can be used to remove the additive noise, such as the Mean of Least Variance (MLV)filter. When the signal is noised by the multiplicative noise, it is difficult to remove. The paper presents an improved filter to remove multiplicative noise by changing the multiplicative noise to the additive noise, and then using the MLV-like to remove the additive noise. The simulation results show that the performance is better than Minimum Coefficient of Variation (MCV) filter and MLV filter. Both one-dimension and image experiments demonstrate its theoretical performance.

  15. System for removing contaminants from plastic resin

    Science.gov (United States)

    Bohnert, George W.; Hand, Thomas E.; DeLaurentiis, Gary M.

    2010-11-23

    A resin recycling system that produces essentially contaminant-free synthetic resin material in an environmentally safe and economical manner. The system includes receiving the resin in container form. A grinder grinds the containers into resin particles. The particles are exposed to a solvent in one or more solvent wash vessels, the solvent contacting the resin particles and substantially removing contaminants on the resin particles. A separator is used to separate the resin particles and the solvent. The resin particles are then placed in solvent removing element where they are exposed to a solvent removing agent which removes any residual solvent remaining on the resin particles after separation.

  16. Removal of failed crown and bridge.

    Science.gov (United States)

    Sharma, Ashu; Rahul, G R; Poduval, Soorya T; Shetty, Karunakar

    2012-07-01

    Crown and bridge have life span of many years but they fail for a number of reasons. Over the years, many devices have been designed to remove crowns and bridges from abutment teeth. While the removal of temporary crowns and bridges is usually very straightforward, the removal of a definitive cast crown with unknown cement is more challenging. Removal is often by destructive means. There are a number of circumstances, however, in which conservative disassembly would aid the practitioner in completing restorative/endodontic procedures. There are different mechanisms available to remove a failed crown or bridge. But there is no information published about the classification of available systems for crown and bridge removal. So it is logical to classify these systems into different groups which can help a clinician in choosing a particular type of system depending upon the clinical situation. The aim of this article is to provide a classification for various crown and bridge removal systems; describe how a number of systems work; and when and why they might be used. A PubMed search of English literature was conducted up to January 2010 using the terms: Crown and bridge removal, Crown and bridge disassembly, Crown and bridge failure. Additionally, the bibliographies of 3 previous reviews, their cross references as well as articles published in various journals like International Endodontic Journal, Journal of Endodontics and were manually searched. Key words:Crown and bridge removal, Crown and bridge disassembly, Crown and bridge failure. PMID:24558549

  17. Hydropower Projects

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-04-02

    The Water Power Program helps industry harness this renewable, emissions-free resource to generate environmentally sustainable and cost-effective electricity. Through support for public, private, and nonprofit efforts, the Water Power Program promotes the development, demonstration, and deployment of advanced hydropower devices and pumped storage hydropower applications. These technologies help capture energy stored by diversionary structures, increase the efficiency of hydroelectric generation, and use excess grid energy to replenish storage reserves for use during periods of peak electricity demand. In addition, the Water Power Program works to assess the potential extractable energy from domestic water resources to assist industry and government in planning for our nation’s energy future. From FY 2008 to FY 2014, DOE’s Water Power Program announced awards totaling approximately $62.5 million to 33 projects focused on hydropower. Table 1 provides a brief description of these projects.

  18. PARTNER Project

    CERN Multimedia

    Ballantine, A; Dixon-Altaber, H; Dosanjh, M; Kuchina, L

    2011-01-01

    Hadrontherapy uses particle beams to treat tumours located near critical organs and tumours that respond poorly to conventional radiation therapy. It has become evident that there is an emerging need for reinforcing research in hadrontherapy and it is essential to train professionals in this rapidly developing field. PARTNER is a 4-year Marie Curie Training project funded by the European Commission with 5.6 million Euros aimed at the creation of the next generation of experts. Ten academic institutes and research centres and two leading companies are participating in PARTNER, that is coordinated by CERN, forming a unique multidisciplinary and multinational European network. The project offers research and training opportunities to 25 young biologists, engineers, physicians and physicists and is allowing them to actively develop modern techniques for treating cancer in close collaboration with leading European Institutions. For this purpose PARTNER relies on cutting edge research and technology development, ef...

  19. Project Phaseolus

    International Nuclear Information System (INIS)

    Research carried out through the Phaseolus Project of the 'Centro de Energia Nuclear na Agricultura' (CENA) Piracicaba, Sao Paulo State, Brazil, is described. It comprises the following subject s: plant breeding; nitrogen fixation; tissue cultures; proteins; photosynthetic efficiency; soil-plant interactions; electron microscopy of the golden mosaic virus; pest control; production of 15N-enriched ammonium sulfate, and determination of elements in the beans plant. (M.A.)

  20. Teseus project

    OpenAIRE

    Petersen, Simone; Marsà, Quim; Chen, Kuan Wei; Arriaga, Lorena; Aleixendri, Joan Josep

    2015-01-01

    This project, TESEUS, is being carried out within the umbrella of the ongoing Urban Node study and focuses on the development of a computational system capable of handling a huge amount of data received from urban nodes in a smart city. There are already existing computer systems with computational power capable of handling the amount of data a smart city requires. Although these computers may provide all the power required to maintain and manage a smart city, they can always b...

  1. Projection Methods

    DEFF Research Database (Denmark)

    Wagner, Falko Jens; Poulsen, Mikael Zebbelin

    1999-01-01

    When trying to solve a DAE problem of high index with more traditional methods, it often causes instability in some of the variables, and finally leads to breakdown of convergence and integration of the solution. This is nicely shown in [ESF98, p. 152 ff.].This chapter will introduce projection...... methods as a way of handling these special problems. It is assumed that we have methods for solving normal ODE systems and index-1 systems....

  2. SUPERSITE PROJECT

    Directory of Open Access Journals (Sweden)

    Silvia Ferrari

    2010-04-01

    Full Text Available The project is focused on a detailed study of some chemical, physical and toxicological parameters and on health, epidemiological and environmental assessment by interpretative models, in the atmosphere of Emilia-Romagna (Italy. The project rises from the necessity to improve  knowledge about environmental and health aspects of fine and ultrafine particles, in primary and secondary components, in the atmosphere. The project, structured in 7 workpackages, is organized in two measurement programmes: the routine one that has a mainly daily time resolution, and the intensive one with high time resolution and a higher chemical speciation than the routine one. The sampling sites are five: three in urban areas (Bologna, Parma and Rimini, one in a rural area (San Pietro Capofiume and one in a remote area (Monte Cimone. Parallel to outdoor studies, a workpackage  is planned for indoor studies and chemical composition analysis with the  outdoor/indoor ratio for characterizing indoor human exposure to outdoor pollution.

  3. Nuclear reactor fuel assembly with fuel rod removal means

    International Nuclear Information System (INIS)

    A fuel assembly is described for a nuclear reactor. The assembly has a bottom nozzle, at least one longitudinally extending control rod guide thimble attached to and projecting upwardly from the bottom nozzle and transverse grids spaced along the thimble. An organized array of elongated fuel rods are transversely spaced and supported by the grids and axially captured between the bottom nozzle and a top nozzle. The assembly comprises: (a) a transversely extending adapter plate formed by an arrangement of integral cross-laced ligaments defining a plurality of coolant flow openings; (b) means for mounting the adapter plate on an upper end portion of the thimble and spaced axially above and disposed transversely over the upper ends of all of the fuel rods present in the fuel assembly such that ones of the ligaments overlie corresponding ones of the fuel rods so as to prevent the fuel rods from moving upwardly through the coolant flow openings; and (c) removable plug means confined within the adapter plate and positioned over and spaced axially above selected ones of the fuel rods in providing access to at least one fuel rod for removal thereof upwardly through the axially spaced adapter plate without removing the top nozzle from the fuel assembly

  4. Turbidity removal: Gravel and charcoal as roughing filtration media

    Directory of Open Access Journals (Sweden)

    Josiah A. Adeyemo

    2010-10-01

    Full Text Available Roughing filtration is an important pre-treatment process for wastewater, because it efficiently separates fine solid particles over prolonged periods, without the addition of chemicals. For this study, a pilot plant was designed at Delmas Coal Mine in the Mpumalanga province of South Africa. The design and sizing of the pilot plant was guided by Wegelin’s design criteria. Gravel was used as a control medium because it is one of the most commonly used roughing filter media and because it was used in developing the criteria. We compared the performance of gravel as a filter medium to that of another locally available material, charcoal, for the removal of turbidity in wastewater. The pilot plant was monitored continuously for 90 days from commissioning until the end of the project. The overall performance of the roughing filter in turbidity removal, using gravel or charcoal, was considered efficient for the pre-treatment of waste water. Charcoal performed slightly better than gravel as a filter medium for the removal of turbidity, possibly because charcoal has a slightly higher specific surface area and porosity than gravel, which could enhance sedimentation and other filtration processes, such as adsorption, respectively.

  5. Colonization of steelhead in a natal stream after barrier removal

    Science.gov (United States)

    Weigel, Dana E.; Connolly, Patrick J.; Martens, Kyle D.; Powell, Madison S.

    2013-01-01

    Colonization of vacant habitats is an important process for supporting the long-term persistence of populations and species. We used a before–after experimental design to follow the process of colonization by steelhead Oncorhynchus mykiss (anadromous Rainbow Trout) at six monitoring sites in a natal stream, Beaver Creek, after the modification or removal of numerous stream passage barriers. Juvenile O. mykiss were collected at monitoring sites by using a backpack electrofisher. Passive integrated transponder tags and instream tag reading stations were used in combination with 16 microsatellite markers to determine the source, extent, and success of migrant O. mykiss after implementation of the barrier removal projects. Steelhead migrated into the study area during the first spawning season after passage was established. Hatchery steelhead, although comprising more than 80% of the adult returns to the Methow River basin, constituted a small proportion (23%) of the adult O. mykiss colonizing the study area. Adult steelhead and fluvial Rainbow Trout entered the stream during the first spawning season after barrier removal and were passing the uppermost tag reader (12 km upstream from the mouth) 3–4 years later. Parr that were tagged in Beaver Creek returned as adults, indicating establishment of the anadromous life history in the study area. Population genetic measures at the lower two monitoring sites (lower 4 km of Beaver Creek) significantly changed within one generation (4–5 years). Colonization and expansion of steelhead occurred more slowly than expected due to the low number of adults migrating into the study area.

  6. Removal of silver nanoparticles by coagulation processes

    International Nuclear Information System (INIS)

    Highlights: • This study investigated the removal of AgNP suspensions by four regular coagulants. • The optimal removal efficiencies for the four coagulants were achieved at pH 7.5. • The removal efficiency of AgNPs was affected by the natural water characteristics. • TEM and XRD showed that AgNPs or silver-containing NPs were adsorbed onto the flocs. -- Abstract: Commercial use of silver nanoparticles (AgNPs) will lead to a potential route for human exposure via potable water. Coagulation followed by sedimentation, as a conventional technique in the drinking water treatment facilities, may become an important barrier to prevent human from AgNP exposures. This study investigated the removal of AgNP suspensions by four regular coagulants. In the aluminum sulfate and ferric chloride coagulation systems, the water parameters slightly affected the AgNP removal. However, in the poly aluminum chloride and polyferric sulfate coagulation systems, the optimal removal efficiencies were achieved at pH 7.5, while higher or lower of pH could reduce the AgNP removal. Besides, the increasing natural organic matter (NOM) would reduce the AgNP removal, while Ca2+ and suspended solids concentrations would also affect the AgNP removal. In addition, results from the transmission electron microscopy and X-ray diffraction showed AgNPs or silver-containing nanoparticles were adsorbed onto the flocs. Finally, natural water samples were used to validate AgNP removal by coagulation. This study suggests that in the case of release of AgNPs into the source water, the traditional water treatment process, coagulation/sedimentation, can remove AgNPs and minimize the silver ion concentration under the well-optimized conditions

  7. Optimized biofilm-based systems for removal of pharmaceuticals from hospital waste water

    DEFF Research Database (Denmark)

    Andersen, Henrik R; Chhetri, Ravi; Hansen, Kamilla;

    Discharge of hospital wastewater is of increasing concern, as hospitals are identified as chemical pollution source due to pharmaceutical content. This project seeks to develop the most efficient and economically feasible technology to remove pharmaceuticals from wastewater, regardless of the poi...... of treatment: at the hospital or at the treatment plant. So far, two biofilm-based technologies are discussed: MBBR and HYBAS....

  8. New concepts of ammonia removal from digested swine effluents using anammox based deammonification process

    Science.gov (United States)

    Production of biogas from swine manure using anaerobic digesters (AD) is projected to be important in the future. However, surplus nitrogen (N) in AD effluents is difficult to remove using current technology (nitrification/denitrification) because low carbon availability after biogas production. W...

  9. Constructed wetlands targeting nitrogen removal in agricultural drainage discharge – a subcatchment scale mitigation strategy

    DEFF Research Database (Denmark)

    Kjærgaard, Charlotte; Hoffmann, Carl Christian; Bruun, Jacob Druedahl;

    analysis of variable mitigation strategies and cost-efficiency analysis reveals that even at low to moderate yearly N removal efficiencies (20-25% N removal efficiency) CWs targeting drainage water are highly efficient and cost-efficient measures. Thus, although challenges remain regarding site...... of recipients, drainage water nutrient loads have a major impact on water quality, and end-of-pipe drainage filter solution may offer the benefits of a targeted measure. This calls for a paradigm shift towards the development of new, cost-efficient technologies to mitigate site-specific nutrient losses...... in agricultural drainage water. The Danish “SUPREME-TECH”project (2010-2016) (www.supremetech.dk) and the innovation project “iDRAIN” (www.idrain.dk ) aims at providing the scientific basis for developing and implementing cost-effective drainage filter technologies targeting N-removal in agricultural subsurface...

  10. Coloss project

    International Nuclear Information System (INIS)

    The COLOSS project was a shared-cost action, co-ordinated by IRSN within the Euratom Research Framework Programme 1998-2002. Started in February 2000, the project lasted three years. The work-programme performed by 19 partners was shaped around complementary activities aimed at improving severe accident codes. Unresolved risk-relevant issues regarding H2 production, melt generation and the source term were studied, through a large number of experiments such as a) dissolution of fresh and high burn-up UO2 and MOX by molten Zircaloy, b) simultaneous dissolution of UO2 and ZrO2 by molten Zircaloy, c) oxidation of U-O-Zr mixtures by steam, d) degradation-oxidation of B4C control rods. Significant results have been produced from separate-effects, semi-global and large-scale tests on COLOSS topics. Break-through were achieved on some issues. Nevertheless, more data are needed for consolidation of the modelling on burn-up effects on UO2 and MOX dissolution and on oxidation of U-O-Zr and B4C-metal mixtures. There was experimental evidence that the oxidation of these mixtures can contribute significantly to the large H2 production observed during the reflooding of degraded cores under severe accident conditions. Based on the experimental results obtained on the COLOSS topics, corresponding models were developed and were successfully implemented in several severe accident codes. Upgraded codes were then used for plant calculations to evaluate the consequences of new models on key severe accident sequences occurring in different plants designs involving B4C control rods (EPR, BWR, VVER- 1000) as well as in the TMI-2 accident. The large series of plant calculations involved sensitivity studies and code benchmarks. Main severe accident codes in use in the EU for safety studies were used such as ICARE/CATHARE, SCDAP/RELAP5, ASTEC, MELCOR and MAAP4. This activity enabled: a) the assessment of codes to calculate core degradation, b) the identification of main uncertainties and

  11. Removal action work plan for the YS-860 Firing Ranges, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    The US Department of Energy is conducting environmental restoration activities at the Y-12 Plant in Oak Ridge, Tennessee. As part of these efforts, a removal action is planned for the former YS-860 Firing Ranges as described in the Action Memorandum for the project. This removal action work plan (RmAWP) is focused on the former YS-860 Firing Ranges, located outside the primary fenceline at the eastern end of the plant. This RmAWP defines the technical approach, procedures, and requirements for the removal of lead-contaminated soil and site restoration of the former YS-860 Firing Ranges at the Y-12 Plant. This RmAWP describes excavation, verification/confirmatory sampling, and reporting requirements for the project. Lower tier plans associated with the RmAWP, which are submitted as separate stand-alone documents, include a field sampling and analysis plan, a health and safety plan, a quality assurance project plan, a waste management plan, a data management implementation plan, and a best management practices plan. A site evaluation of the YS-86O Firing Ranges conducted in 1996 by Lockheed Martin Energy Systems, Inc., determined that elevated lead levels were present in the Firing Ranges target berm soils. The results of this sampling event form the basis for the removal action recommendation as described in the Action Memorandum for this project. This RmAWP contains a brief history and description of the Former YS-860 Firing Ranges Project, along with the current project schedule and milestones. This RmAWP also provides an overview of the technical requirements of the project, including a summary of the approach for the removal activities. Finally, the RmAWP identifies the regulatory requirements and the appropriate removal action responses to address applicable or relevant and appropriate requirements to achieve the project goals of substantially reducing the risk to human health and the environment

  12. Removal action work plan for the YS-860 Firing Ranges, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The US Department of Energy is conducting environmental restoration activities at the Y-12 Plant in Oak Ridge, Tennessee. As part of these efforts, a removal action is planned for the former YS-860 Firing Ranges as described in the Action Memorandum for the project. This removal action work plan (RmAWP) is focused on the former YS-860 Firing Ranges, located outside the primary fenceline at the eastern end of the plant. This RmAWP defines the technical approach, procedures, and requirements for the removal of lead-contaminated soil and site restoration of the former YS-860 Firing Ranges at the Y-12 Plant. This RmAWP describes excavation, verification/confirmatory sampling, and reporting requirements for the project. Lower tier plans associated with the RmAWP, which are submitted as separate stand-alone documents, include a field sampling and analysis plan, a health and safety plan, a quality assurance project plan, a waste management plan, a data management implementation plan, and a best management practices plan. A site evaluation of the YS-86O Firing Ranges conducted in 1996 by Lockheed Martin Energy Systems, Inc., determined that elevated lead levels were present in the Firing Ranges target berm soils. The results of this sampling event form the basis for the removal action recommendation as described in the Action Memorandum for this project. This RmAWP contains a brief history and description of the Former YS-860 Firing Ranges Project, along with the current project schedule and milestones. This RmAWP also provides an overview of the technical requirements of the project, including a summary of the approach for the removal activities. Finally, the RmAWP identifies the regulatory requirements and the appropriate removal action responses to address applicable or relevant and appropriate requirements to achieve the project goals of substantially reducing the risk to human health and the environment.

  13. Biomodification of coal to remove mercury

    Science.gov (United States)

    A biological process for removal of mercury from coal is under investigation. Iron and sulfur oxidizing bacteria have previously been used for desulfurization of coal and for mineral mining. We have shown that removal of mercury from coal is also possible via the same principles. Two pure culture...

  14. 5 CFR 359.403 - Removal: Conduct.

    Science.gov (United States)

    2010-01-01

    ... EXECUTIVE SERVICE; GUARANTEED PLACEMENT IN OTHER PERSONNEL SYSTEMS Removal of Career Appointees During... failure to accept a directed reassignment or to accompany a position in a transfer of function. (2) This... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Removal: Conduct. 359.403 Section...

  15. Method of removing contaminants from plastic resins

    Science.gov (United States)

    Bohnert,George W.; Hand,Thomas E.; Delaurentiis,Gary M.

    2007-08-07

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  16. Method for removing contaminants from plastic resin

    Science.gov (United States)

    Bohnert, George W.; Hand, Thomas E.; DeLaurentiis, Gary M.

    2008-12-30

    A method for removing contaminants from synthetic resin material containers using a first organic solvent system and a second carbon dioxide system. The organic solvent is utilized for removing the contaminants from the synthetic resin material and the carbon dioxide is used to separate any residual organic solvent from the synthetic resin material.

  17. Arsenic removal from drinking water during coagulation

    Energy Technology Data Exchange (ETDEWEB)

    Hering, J.G. [California Inst. of Tech., Pasadena, CA (United States); Chen, P.Y. [Industrial Technology Research Inst., Chutung Hsinchu (Taiwan, Province of China); Wilkie, J.A.; Elimelech, M. [Univ. of California, Los Angeles, CA (United States). Dept. of Civil and Environmental Engineering

    1997-08-01

    The efficiency of arsenic removal from source waters and artificial freshwaters during coagulation with ferric chloride and alum was examined in bench-scale studies. Arsenic(V) removal by either ferric chloride or alum was relatively insensitive to variations in source water composition below pH 8. At pH 8 and 9, the efficiency of arsenic(V) removal by ferric chloride was decreased in the presence of natural organic matter. The pH range for arsenic(V) removal with alum was more restricted than with ferric chloride. For source waters spiked with 20 {micro}g/L arsenic(V), final dissolved arsenic(V) concentrations in the product water of less than 2 {micro}g/L were achieved with both coagulants at neutral pH. Removal of arsenic(III) from source waters by ferric chloride was both less efficient and more strongly influenced by source water composition than removal of arsenic(V). The presence of sulfate (at pH 4 and 5) and natural organic matter (at pH 4 through 9) adversely affected the efficiency of arsenic(III) removal by ferric chloride. Arsenic(III) could not be removed from source waters by coagulation with alum.

  18. REMOVAL OF RADIUM FROM DRINKING WATER

    Science.gov (United States)

    This report summarizes processes for removal of radium from drinking water. Ion exchange, including strong acid and weak acid resin, is discussed. Both processes remove better than 95 percent of the radium from the water. Weak acid ion exchange does not add sodium to the water...

  19. Oral biofilm models for mechanical plaque removal

    NARCIS (Netherlands)

    Verkaik, Martinus J.; Busscher, Henk J.; Rustema-Abbing, Minie; Slomp, Anje M.; Abbas, Frank; van der Mei, Henny C.

    2010-01-01

    In vitro plaque removal studies require biofilm models that resemble in vivo dental plaque. Here, we compare contact and non-contact removal of single and dual-species biofilms as well as of biofilms grown from human whole saliva in vitro using different biofilm models. Bacteria were adhered to a sa

  20. Removal of heavy metals using waste eggshell

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The removal capacity of toxic heavy metals by the reused eggshell was studied. As a pretreatment process for the preparation of reused material from waste eggshell, calcination was performed in the furnace at 800℃ for 2 h after crushing the dried waste eggshell. Calcination behavior, qualitative and quantitative elemental information, mineral type and surface characteristics before and after calcination of eggshell were examined by thermal gravimetric analysis (TGA), X-ray fluorescence (XRF), X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. After calcination, the major inorganic composition was identified as Ca (lime, 99.63%) and K, P and Sr were identified as minor components. When calcined eggshell was applied in the treatment of synthetic wastewater containing heavy metals, a complete removal of Cd as well as above 99% removal of Cr was observed after 10 min. Although the natural eggshell had some removal capacity of Cd and Cr, a complete removal was not accomplished even after 60 min due to quite slower removal rate. However, in contrast to Cd and Cr, an efficient removal of Pb was observed with the natural eggshell rather than the calcined eggshell. From the application of the calcined eggshell in the treatment of real electroplating wastewater, the calcined eggshell showed a promising removal capacity of heavy metal ions as well as had a good neutralization capacity in the treatment of strong acidic wastewater.

  1. NITROGEN REMOVAL FROM NATURAL GAS

    Energy Technology Data Exchange (ETDEWEB)

    K.A. Lokhandwala; M.B. Ringer; T.T. Su; Z. He; I. Pinnau; J.G. Wijmans; A. Morisato; K. Amo; A. DaCosta; R.W. Baker; R. Olsen; H. Hassani; T. Rathkamp

    1999-12-31

    The objective of this project was to develop a membrane process for the denitrogenation of natural gas. Large proven reserves in the Lower-48 states cannot be produced because of the presence of nitrogen. To exploit these reserves, cost-effective, simple technology able to reduce the nitrogen content of the gas to 4-5% is required. Technology applicable to treatment of small gas streams (below 10 MMscfd) is particularly needed. In this project membranes that selectively permeate methane and reject nitrogen in the gas were developed. Preliminary calculations show that a membrane with a methane/nitrogen selectivity of 3 to 5 is required to make the process economically viable. A number of polymer materials likely to have the required selectivities were evaluated as composite membranes. Polyacetylenes such as poly(1-trimethylsilyl-1-propyne) [PTMSP] and poly(4-methyl-2-pentyne) [PMP] had high selectivities and fluxes, but membranes prepared from these polymers were not stable, showing decreasing flux and selectivity during tests lasting only a few hours. Parel, a poly(propylene oxide allyl glycidyl ether) had a selectivity of 3 at ambient temperatures and 4 or more at temperatures of {minus}20 C. However, Parel is no longer commercially available, and we were unable to find an equivalent material in the time available. Therefore, most of our experimental work focused on silicone rubber membranes, which have a selectivity of 2.5 at ambient temperatures, increasing to 3-4 at low temperatures. Silicone rubber composite membranes were evaluated in bench-scale module tests and with commercial-scale, 4-inch-diameter modules in a small pilot plant. Over six days of continuous operation at a feed gas temperature of {minus}5 to {minus}10 C, the membrane maintained a methane/nitrogen selectivity of about 3.3. Based on the pilot plant performance data, an analysis of the economic potential of the process was prepared. We conclude that a stand-alone membrane process is the lowest

  2. BOA: Asbestos pipe insulation removal robot system. Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Schempf, H.; Bares, J.E.

    1995-02-01

    The project described in this report targets the development of a mechanized system for safe, cost-efficient and automated abatement of asbestos containing materials used as pipe insulation. Based on several key design criteria and site visits, a proof-of-concept prototype robot system, dubbed BOA, was designed and built, which automatically strips the lagging and insulation from the pipes, and encapsulates them under complete vacuum operation. The system can operate on straight runs of piping in horizontal or vertical orientations. Currently we are limited to four-inch diameter piping without obstacles as well as a somewhat laborious emplacement and removal procedure -- restrictions to be alleviated through continued development. BOA removed asbestos at a rate of 4-5 ft./h compared to 3 ft./h for manual removal of asbestos with a 3-person crew. The containment and vacuum system on BOA was able to achieve the regulatory requirement for airborne fiber emissions of 0.01 fibers/ccm/ 8-hr. shift. This program consists of two phases. The first phase was completed and a demonstration was given to a review panel, consisting of DOE headquarters and site representatives as well as commercial abatement industry representatives. Based on the technical and programmatic recommendations drafted, presented and discussed during the review meeting, a new plan for the Phase II effort of this project was developed. Phase 11 will consist of a 26-month effort, with an up-front 4-month site-, market-, cost/benefit and regulatory study before the next BOA robot (14 months) is built, and then deployed and demonstrated (3 months) at a DOE site (such as Fernald or Oak Ridge) by the beginning of FY`97.

  3. Flattening filter removal for improved image quality of megavoltage fluoroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, James D.; Kirichenko, Alexander; Gayou, Olivier [Department of Radiation Oncology, Allegheny General Hospital, Pittsburgh, Pennsylvania 15212 (United States)

    2013-08-15

    Purpose: Removal of the linear accelerator (linac) flattening filter enables a high rate of dose deposition with reduced treatment time. When used for megavoltage imaging, an unflat beam has reduced primary beam scatter resulting in sharper images. In fluoroscopic imaging mode, the unflat beam has higher photon count per image frame yielding higher contrast-to-noise ratio. The authors’ goal was to quantify the effects of an unflat beam on the image quality of megavoltage portal and fluoroscopic images.Methods: 6 MV projection images were acquired in fluoroscopic and portal modes using an electronic flat-panel imager. The effects of the flattening filter on the relative modulation transfer function (MTF) and contrast-to-noise ratio were quantified using the QC3 phantom. The impact of FF removal on the contrast-to-noise ratio of gold fiducial markers also was studied under various scatter conditions.Results: The unflat beam had improved contrast resolution, up to 40% increase in MTF contrast at the highest frequency measured (0.75 line pairs/mm). The contrast-to-noise ratio was increased as expected from the increased photon flux. The visualization of fiducial markers was markedly better using the unflat beam under all scatter conditions, enabling visualization of thin gold fiducial markers, the thinnest of which was not visible using the unflat beam.Conclusions: The removal of the flattening filter from a clinical linac leads to quantifiable improvements in the image quality of megavoltage projection images. These gains enable observers to more easily visualize thin fiducial markers and track their motion on fluoroscopic images.

  4. Electro-Optic Imaging Fourier Transform Spectral Polarimeter Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Boulder Nonlinear Systems, Inc. (BNS) proposes to develop an Electro-Optic Imaging Fourier Transform Spectral Polarimeter (E-O IFTSP). The polarimetric system is...

  5. Atrazine removal in Danish anaerobic aquifers

    DEFF Research Database (Denmark)

    Pedersen, Philip Grinder; Arildskov, N.P.; Albrechtsen, Hans-Jørgen

    2002-01-01

    The pesticide atrazine (6-chloro-N-2-ethyl-N-4-isopropyl-1,3,5-triazine -2,4-diamine) was removed from the water phase in anaerobic laboratory batch incubations with sediment and groundwater from a number of Danish anaerobic aquifers, but not in incubations from aerobic aquifers. The removal...... process was abiotic since atrazine was also removed from microbially inhibited autoclaved and chloroform amended controls, although in controls amended with mercury, atrazine removal was slowed down. (ring-U-C-14)- atrazine amended samples showed no mineralization to (CO2)-C-14 or transformation...... to soluble degradation products, indicating that a slow sorption process was responsible for the atrazine removal. Approximately 20% of the applied C-14-atrazine was present in a non-extractable residual sediment bound fraction, indicating the slow sorption process to be in part irreversible...

  6. FLOAT Project

    DEFF Research Database (Denmark)

    Sørensen, Eigil V.; Aarup, Bendt

    The objective of the FLOAT project is to study the reliability of high-performance fibre-reinforced concrete, also known as Compact Reinforced Composite (CRC), for the floats of wave energy converters. In order to reach a commercial breakthrough, wave energy converters need to achieve a lower price...... of energy produced, comparable to prices currently obtained from offshore wind power, and this can be done by the use of more suitable materials. The flotation device is a key part of converters, as it accounts for a considerable share of initial investment, up to 27% depending on the converter. CRC floats...

  7. Project Lyman

    OpenAIRE

    McCandliss, Stephan R.; Kruk, Jeffrey W.; Blair, William P.; Kaiser, Mary Elizabeth; Feldman, Paul D.; Meurer, Gerhardt R.; Dixon, William V.; Sahnow, David J.; Neufeld, David A.; Lupu, Roxana E.; Fleming, Brian; Smee, Stephen A.; Andersson, B. G.; Moseley, Samuel H.; Kutyrev, Alexander S.

    2008-01-01

    We explore the design of a space mission, Project Lyman, which has the goal of quantifying the ionization history of the universe from the present epoch to a redshift of z ~ 3. Observations from WMAP and SDSS show that before a redshift of z >~ 6 the first collapsed objects, possibly dwarf galaxies, emitted Lyman continuum (LyC) radiation shortward of 912 A, reionizing most of the universe. How LyC escapes from galactic environments, whether it induces positive or negative feedback on the loc...

  8. Pré-filtração em pedregulho e filtração lenta com areia, manta não tecida e carvão ativado para polimento de efluentes domésticos tratados em leitos cultivados Pré-filtration in boulder and slow sand filtration with non-woven synthetic layers and granulated vegetal coal to improve quality in wastewater treated by constructed wetlands

    Directory of Open Access Journals (Sweden)

    José E. S. Paterniani

    2011-01-01

    Full Text Available O presente trabalho teve como objetivo comparar sistemas de filtragem, composto de pré-filtro de pedregulho seguido de filtro lento com o meio filtrante areia e no topo manta sintética não tecida e pré-filtro de pedregulho seguido de filtro lento com meio filtrante areia e carvão ativado granular e no topo manta sintética não tecida, para polimento de efluentes domésticos tratados em leitos cultivados, visando à aplicação na fertirrigação. Na comparação dos sistemas de filtragem, avaliou-se a eficiência de remoção dos parâmetros: sólidos em suspensão, turbidez, cor aparente, demanda química de oxigênio, oxigênio dissolvido, ferro, manganês, coliformes totais e E. coli. Os dois sistemas operavam 24 horas por dia, com a mesma taxa de aplicação, tratando uma vazão total final de 1,5 m³ dia-1, sendo que a taxa de aplicação para a unidade de pré-filtração era, em média, de 8,4 m³ m-2 dia-1 e para cada uma das unidades de filtração lenta era, em media, de 2,7 m³ m-2 dia-1. As unidades de pré-filtração e filtração lenta mostraram-se eficientes na redução das concentrações de sólidos suspensos, turbidez, cor aparente e DQO, como polimento de esgotos domésticos previamente tratados. O uso de carvão ativado granular, em combinação com areia, proporcionou ao filtro lento maior eficiência na remoção de sólidos suspensos, cor, turbidez, coliformes totais e E. Coli., sem com isso aumentar a perda de carga inicial. Existe a possibilidade de utilização dos efluentes para a prática da fertirrigação, sendo necessário o processo de desinfecção ou não, dependendo da cultura e o sistema de irrigação utilizado.The objective of this study was the comparison between two filtration systems, being one composed of a boulder pre-filter followed by a slow filter with sand as filtration media and a non-woven synthetic fabric in the upper part, and the other one composed of a boulder pre-filter followed by a

  9. Review on Various Algorithm for Cloud Detection and Removal for Images

    Directory of Open Access Journals (Sweden)

    Ms.Manisha Raut,

    2015-03-01

    Full Text Available Clouds is one of the significant obstacles in extracting information from tea lands using remote sensing imagery Different approaches have been attempted to solve this problem with varying levels of success In the past decade, a number of cloud removal approaches have been proposed . In this paper we review and discuss about the cloud detection & removal, need of cloud computing , its principles, and cloud removal process and various algorithm of cloud removal. This paper attempts to give a recipe for selecting one of the popular cloud removal algorithms like The Information Cloning Algorithm, Cloud Distortion Model And Filtering Procedure, SemiAutomated Cloud/Shadow, And Haze Identification And Removal etc. A cloud removal approach based on information cloning is introduced...Using generic interpolation machinery based on solving Poisson equations, a variety of novel tools are introduced for seamless editing of image regions. The patch-based information reconstruction is mathematically formulated as a Poisson equation and solved using a global optimization process. Based on the specific requirements of the project that necessitates the utilization of certain types of cloud detection algorithms is decided

  10. Project Success in IT Project Management

    OpenAIRE

    Siddiqui, Farhan Ahmed

    2010-01-01

    The rate of failed and challenged Information Technology (IT) projects is too high according to the CHAOS Studies by the Standish Group and the literature on project management (Standish Group, 2008). The CHAOS Studies define project success as meeting the triple constraints of scope, time, and cost. The criteria for project success need to be agreed by all parties before the start of the project and constantly reviewed as the project progresses. Assessing critical success factors is another ...

  11. FLORAM project

    Energy Technology Data Exchange (ETDEWEB)

    Zulauf, W.E. [Sao Paolos Environmental Secretariat, Sao Paolo (Brazil); Goelho, A.S.R. [Riocell, S.A. (Brazil); Saber, A. [IEA-Instituto de Estudos Avancados (Brazil)] [and others

    1995-12-31

    The project FLORAM was formulated at the `Institute for Advanced Studies` of the University of Sao Paulo. It aims at decreasing the level of carbon dioxide in the atmosphere and thus curbing the green-house effect by way of a huge effort of forestation and reforestation. The resulting forests when the trees mature, will be responsible for the absorption of about 6 billion tons of excess carbon. It represents 5 % of the total amount of CO{sub 2} which is in excess in the earth`s atmosphere and represents 5 % of the available continental surfaces which can be forested as well. Therefore, if similar projects are implemented throughout the world, in theory all the exceeding CO{sub 2}, responsible for the `greenhouse effect`, (27 % or 115 billion tons of carbon) would be absorbed. Regarding this fact, there would be a 400 million hectar increase of growing forests. FLORAM in Brazil aims to plant 20.000.000 ha in 2 years at a cost of 20 billion dollars. If it reaches its goals that will mean that Brazil will have reforested an area almost half as big as France. (author)

  12. PORTNUS Project

    Energy Technology Data Exchange (ETDEWEB)

    Loyal, Rebecca E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-07-14

    The objective of the Portunus Project is to create large, automated offshore ports that will the pace and scale of international trade. Additionally, these ports would increase the number of U.S. domestic trade vessels needed, as the imported goods would need to be transported from these offshore platforms to land-based ports such as Boston, Los Angeles, and Newark. Currently, domestic trade in the United States can only be conducted by vessels that abide by the Merchant Marine Act of 1920 – also referred to as the Jones Act. The Jones Act stipulates that vessels involved in domestic trade must be U.S. owned, U.S. built, and manned by a crew made up of U.S. citizens. The Portunus Project would increase the number of Jones Act vessels needed, which raises an interesting economic concern. Are Jones Act ships more expensive to operate than foreign vessels? Would it be more economically efficient to modify the Jones Act and allow vessels manned by foreign crews to engage in U.S. domestic trade? While opposition to altering the Jones Act is strong, it is important to consider the possibility that ship-owners who employ foreign crews will lobby for the chance to enter a growing domestic trade market. Their success would mean potential job loss for thousands of Americans currently employed in maritime trade.

  13. SISCAL project

    Science.gov (United States)

    Santer, Richard P.; Fell, Frank

    2003-05-01

    The first "ocean colour" sensor, Coastal Zone Color Scanner (CZCS), was launched in 1978. Oceanographers learnt a lot from CZCS but it remained a purely scientific sensor. In recent years, a new generation of satellite-borne earth observation (EO) instruments has been brought into space. These instruments combine high spectral and spatial resolution with revisiting rates of the order of one per day. More instruments with further increased spatial, spectral and temporal resolution will be available within the next years. In the meantime, evaluation procedures taking advantage of the capabilities of the new instruments were derived, allowing the retrieval of ecologically important parameters with higher accuracy than before. Space agencies are now able to collect and to process satellite data in real time and to disseminate them via the Internet. It is therefore meanwhile possible to envisage using EO operationally. In principle, a significant demand for EO data products on terrestrial or marine ecosystems exists both with public authorities (environmental protection, emergency management, natural resources management, national parks, regional planning, etc) and private companies (tourist industry, insurance companies, water suppliers, etc). However, for a number of reasons, many data products that can be derived from the new instruments and methods have not yet left the scientific community towards public or private end users. It is the intention of the proposed SISCAL (Satellite-based Information System on Coastal Areas and Lakes) project to contribute to the closure of the existing gap between space agencies and research institutions on one side and end users on the other side. To do so, we intend to create a data processor that automatically derives and subsequently delivers over the Internet, in Near-Real-Time (NRT), a number of data products tailored to individual end user needs. The data products will be generated using a Geographical Information System (GIS

  14. PROJECT TEAM MOTIVATION IN PROJECT REALISATION

    OpenAIRE

    Perica Jankoviæ

    2014-01-01

    Managing a project team is an everyday activity when managing a project realization. In order to accomplish efficiency at work on a project, it is necessary for all the participants in the project to be motivated and interested, focused on accomplishing the project. To the end of providing greater motivation of the project team for the realization of the project, the project manager should be very well acquainted with the needs and motives of the people he/she is managing and should find the ...

  15. Sorbent Structural Impacts Due to Humidity on Carbon Dioxide Removal Sorbents for Advanced Exploration Systems

    Science.gov (United States)

    Watson, David; Knox, James C.; West, Phillip; Stanley, Christine M.; Bush, Richard

    2015-01-01

    The Life Support Systems Project (LSSP) under the Advanced Exploration Systems (AES) program builds upon the work performed under the AES Atmosphere Resource Recovery and Environmental Monitoring (ARREM) project focusing on the numerous technology development areas. The CO2 removal and associated air drying development efforts are focused on improving the current state-of-the-art system on the International Space Station (ISS) utilizing fixed beds of sorbent pellets by seeking more robust pelletized sorbents, evaluating structured sorbents, and examining alternate bed configurations to improve system efficiency and reliability. A component of the CO2 removal effort encompasses structural stability testing of existing and emerging sorbents. Testing will be performed on dry sorbents and sorbents that have been conditioned to three humidity levels. This paper describes the sorbent structural stability screening efforts in support of the LSS Project within the AES Program.

  16. Removal of metals in constructed wetlands

    Energy Technology Data Exchange (ETDEWEB)

    Crites, R.W.; Watson, R.C.; Williams, C.R.

    1996-12-31

    Trace metals are difficult to remove from municipal wastewater by conventional wastewater treatment methods. Constructed wetlands have the potential to trap and remove metals from the water column. Long term removal is expected to occur by accumulation and burial in the plant detritus in a manner similar to the removal of phosphorus. Few data are available in the literature on removal of metals by constructed wetlands. A free water surface constructed wetland at Sacramento Regional Wastewater Treatment Plant treating secondary municipal effluent has been operating since the spring of 1994. Removal data for 13 metals are presented for the period from August 1994 to May 1995. About 3,785 m{sup 3}/d (1 mgd) of pure oxygen activated sludge effluent, disinfected using UV light, is further treated through a 8 ha (20 acre) constructed wetlands Ten separate, parallel treatment cells are available to demonstrate the effects of detention time, vegetation management, and application frequency on the removal of metals, organics and ammonia. Detention time can be varied from 3 to 13 days by varying the flow and the water depth. The vegetation, primarily bulrush with some cattails, will be managed by different techniques to minimize mosquito production. Application frequency varies from continuous flow to batch flow (1 to 2 days of loading with 1 day of discharge).

  17. SULFURIC ACID REMOVAL PROCESS EVALUATION: LONG-TERM RESULTS

    Energy Technology Data Exchange (ETDEWEB)

    Gary M. Blythe; Richard McMillan

    2002-07-03

    The objective of this project is to demonstrate the use of alkaline reagents injected into the furnace of coal-fired boilers as a means of controlling sulfuric acid emissions. The project is being co-funded by the U.S. DOE National Energy Technology Laboratory, under Cooperative Agreement DE-FC26-99FT40718, along with EPRI, the American Electric Power Company (AEP), FirstEnergy Corp., the Tennessee Valley Authority, and Dravo Lime, Inc. Sulfuric acid controls are becoming of increasing interest to power generators with coal-fired units for a number of reasons. Sulfuric acid is a Toxic Release Inventory species and can cause a variety of plant operation problems such as air heater plugging and fouling, back-end corrosion, and plume opacity. These issues will likely be exacerbated with the retrofit of selective catalytic reduction (SCR) for NO{sub x} control on many coal-fired plants, as SCR catalysts are known to further oxidize a portion of the flue gas SO{sub 2} to SO{sub 3}. The project previously tested the effectiveness of furnace injection of four different calcium-and/or magnesium-based alkaline sorbents on full-scale utility boilers. These reagents were tested during four one- to two-week tests conducted on two FirstEnergy Bruce Mansfield Plant (BMP) units. One of the sorbents tested was a magnesium hydroxide byproduct slurry produced from a modified Thiosorbic{reg_sign} Lime wet flue gas desulfurization system. The other three sorbents are available commercially and include dolomite, pressure-hydrated dolomitic lime, and commercial magnesium hydroxide. The dolomite reagent was injected as a dry powder through out-of-service burners, while the other three reagents were injected as slurries through air-atomizing nozzles inserted through the front wall of the upper furnace, either across from the nose of the furnace or across from the pendant superheater tubes. After completing the four one- to two-week tests, the most promising sorbents were selected for

  18. Biological Phosphorus Removal in a Moving Bed Biofilm Reactor

    OpenAIRE

    Helness, Herman

    2007-01-01

    Phosphorus (P) and nitrogen (N) removal from municipal wastewater is performed to prevent or reduce eutrophication in the receiving water.Both P and N can be removed physical/chemically as well as biologically. While biological processes have always dominated in N-removal, chemical P-removal is used in many cases. Biological P-removal using enhanced biological phosphorus removal (EBPR) is normally carried out in suspended culture (activated sludge) processes while biological N-removal (throug...

  19. Removable bearing arrangement for a wind turbine generator

    Science.gov (United States)

    Bagepalli, Bharat Sampathkumaran; Jansen, Patrick Lee; Gadre, Aniruddha Dattatraya

    2010-06-15

    A wind generator having removable change-out bearings includes a rotor and a stator, locking bolts configured to lock the rotor and stator, a removable bearing sub-assembly having at least one shrunk-on bearing installed, and removable mounting bolts configured to engage the bearing sub-assembly and to allow the removable bearing sub-assembly to be removed when the removable mounting bolts are removed.

  20. Reasons for removal of the moon

    Directory of Open Access Journals (Sweden)

    S. Orlov

    2015-09-01

    Full Text Available In article the new concept of an explanation of the reason of removal of the Moon from Earth is offered to consideration. It is based on the theory of vortex gravitation, cosmology and a cosmogony. The main reason for this removal is that gravity, the earth's field does not create our planet, and ether vortex The orbital plane of the Moon doesn't coincide with the plane of a gravitational whirlwind that creates reduction of forces of an attraction of the Moon to Earth on some sites of its orbit. Removal of a lunar orbit happens a consequence of it.