Static Formation Temperature Prediction Based on Bottom Hole Temperature

Directory of Open Access Journals (Sweden)

Changwei Liu

2016-08-01

Full Text Available Static formation temperature (SFT is required to determine the thermophysical properties and production parameters in geothermal and oil reservoirs. However, it is not easy to determine SFT by both experimental and physical methods. In this paper, a mathematical approach to predicting SFT, based on a new model describing the relationship between bottom hole temperature (BHT and shut-in time, has been proposed. The unknown coefficients of the model were derived from the least squares fit by the particle swarm optimization (PSO algorithm. Additionally, the ability to predict SFT using a few BHT data points (such as the first three, four, or five points of a data set was evaluated. The accuracy of the proposed method to predict SFT was confirmed by a deviation percentage less than ±4% and a high regression coefficient R2 (>0.98. The proposed method could be used as a practical tool to predict SFT in both geothermal and oil wells.

Bottom-pressure observations of deep-sea internal hydrostatic and non-hydrostatic motions

NARCIS (Netherlands)

van Haren, H.

2013-01-01

In the ocean, sloping bottom topography is important for the generation and dissipation of internal waves. Here, the transition of such waves to turbulence is demonstrated using an accurate bottom-pressure sensor that was moored with an acoustic Doppler current profiler and high-resolution

Far-field tsunami magnitude determined from ocean-bottom pressure gauge data around Japan

Science.gov (United States)

Baba, T.; Hirata, K.; Kaneda, Y.

2003-12-01

\\hspace*{3mm}Tsunami magnitude is the most fundamental parameter to scale tsunamigenic earthquakes. According to Abe (1979), the tsunami magnitude, Mt, is empirically related to the crest to trough amplitude, H, of the far-field tsunami wave in meters (Mt = logH + 9.1). Here we investigate the far-field tsunami magnitude using ocean-bottom pressure gauge data. The recent ocean-bottom pressure measurements provide more precise tsunami data with a high signal-to-noise ratio. \\hspace*{3mm}Japan Marine Science and Technology Center is monitoring ocean bottom pressure fluctuations using two submarine cables of depths of 1500 - 2400 m. These geophysical observatory systems are located off Cape Muroto, Southwest Japan, and off Hokkaido, Northern Japan. The ocean-bottom pressure data recorded with the Muroto and Hokkaido systems have been collected continuously since March, 1997 and October, 1999, respectively. \\hspace*{3mm}Over the period from March 1997 to June 2003, we have observed four far-field tsunami signals, generated by earthquakes, on ocean-bottom pressure records. These far-field tsunamis were generated by the 1998 Papua New Guinea eq. (Mw 7.0), 1999 Vanuatu eq. (Mw 7.2), 2001 Peru eq. (Mw 8.4) and 2002 Papua New Guinea eq. (Mw 7.6). Maximum amplitude of about 30 mm was recorded by the tsunami from the 2001 Peru earthquake. \\hspace*{3mm}Direct application of the Abe's empirical relation to ocean-bottom pressure gauge data underestimates tsunami magnitudes by about an order of magnitude. This is because the Abe's empirical relation was derived only from tsunami amplitudes with coastal tide gauges where tsunami is amplified by the shoaling of topography and the reflection at the coastline. However, these effects do not work for offshore tsunami in deep oceans. In general, amplification due to shoaling near the coastline is governed by the Green's Law, in which the tsunami amplitude is proportional to h-1/4, where h is the water depth. Wave amplitude also is

High-frequency bottom-pressure and acoustic variations in a sea strait: internal wave turbulence

NARCIS (Netherlands)

van Haren, H.

2012-01-01

During a period of 3 days, an accurate bottom-pressure sensor and a four-beam acoustic Doppler current profiler (ADCP) were mounted in a bottom frame at 23 m in a narrow sea strait with dominant near-rectilinear tidal currents exceeding 1 m s(-1) in magnitude. The pressure record distinguishes small

Precise Comparisons of Bottom-Pressure and Altimetric Ocean Tides

Science.gov (United States)

Ray, Richard D.

2013-01-01

A new set of pelagic tide determinations is constructed from seafloor pressure measurements obtained at 151 sites in the deep ocean. To maximize precision of estimated tides, only stations with long time series are used; median time series length is 567 days. Geographical coverage is considerably improved by use of the international tsunami network, but coverage in the Indian Ocean and South Pacific is still weak. As a tool for assessing global ocean tide models, the data set is considerably more reliable than older data sets : the root-mean-square difference with a recent altimetric tide model is approximately 5 mm for the M2 constituent. Precision is sufficiently high to allow secondary effects in altimetric and bottom-pressure tide differences to be studied. The atmospheric tide in bottom pressure is clearly detected at the S1, S2, and T2 frequencies. The altimetric tide model is improved if satellite altimetry is corrected for crustal loading by the atmospheric tide. Models of the solid body tide can also be constrained. The free corenutation effect in the K1 Love number is easily detected, but the overall estimates are not as accurate as a recent determination with very long baseline interferometry.

Precise comparisons of bottom-pressure and altimetric ocean tides

Science.gov (United States)

Ray, R. D.

2013-09-01

A new set of pelagic tide determinations is constructed from seafloor pressure measurements obtained at 151 sites in the deep ocean. To maximize precision of estimated tides, only stations with long time series are used; median time series length is 567 days. Geographical coverage is considerably improved by use of the international tsunami network, but coverage in the Indian Ocean and South Pacific is still weak. As a tool for assessing global ocean tide models, the data set is considerably more reliable than older data sets: the root-mean-square difference with a recent altimetric tide model is approximately 5 mm for the M2 constituent. Precision is sufficiently high to allow secondary effects in altimetric and bottom-pressure tide differences to be studied. The atmospheric tide in bottom pressure is clearly detected at the S1, S2, and T2 frequencies. The altimetric tide model is improved if satellite altimetry is corrected for crustal loading by the atmospheric tide. Models of the solid body tide can also be constrained. The free core-nutation effect in the K1 Love number is easily detected, but the overall estimates are not as accurate as a recent determination with very long baseline interferometry.

Development of computational tool to interpret real time Pd (Pressure While Drilling) data; Desenvolvimento de ferramenta computacional interpretadora de dados de PWD (Pressure While Drilling) em tempo real

Energy Technology Data Exchange (ETDEWEB)

Gandelman, Roni Abensur; Waldmann, Alex Tadeu de Almeida; Martins, Andre Leibsohn [Centro de Pesquisas da Petrobras (CENPES). Gerencia de Tecnologia de Engenharia de Poco (Brazil)], e-mails: roniag@petrobras.com.br, awaldmann@petrobras.com.br, aleibsohn@petrobras.com.br; Teixeira, Gleber Tacio; Aragao, Atila Fernando Lima [E and P Servicos. Gerencia de Servicos de Poco (Brazil)], e-mail: gleber@petrobras.com.br, atila_aragao@petrobras.com.br; Rezende, Mauricio Seiji; Kern, Eduardo; Maliska Junior, Clovis [Engineering Simulation and Scientific Software (ESSS), (Brazil)], e-mails: mauricio@esss.com.br, kern@esss.com.br, coi@esss.com.br

2008-12-15

Drilling offshore oil wells is a very expensive and complex process, in which all the efforts must be taken to keep the annular pressure between a minimum pressure (pore pressure) and a maximum pressure (fracture pressure) which define the operational window limits. Several phenomena impact the bottom hole annular pressures, such as: ineffective hole cleaning, gel breaking when circulation is resumed, drill string movement (surge and swab), trips, pills displacement, kicks, etc. The correct interpretation of pressure while drilling (PWD) data is a very powerful toll to identify and prevent these phenomena. Nowadays, an expert monitors bottom hole pressures data and identifies undesirable events. The main goal of this project is the development of a computational tool to monitor pressure (and mud logging) data in real time to identify the causes of abnormal pressure variations, helping the operators to take decisions rapidly. Besides that, the tool allows the user to handle PWD data in a flexible architecture. This flexibility allows the incorporation of new methods of events identification as they are developed. The ultimate goals is to obtain a tool which serves both for the key study of the problems and physical, specific phenomena found during drilling, both for real-time monitoring to assist professionals involved in the process. (author)

[Injection Pressure Evaluation of the New Venous Catheter with Side Holes for Contrast-enhanced CT/MRI].

Science.gov (United States)

Fukuda, Junya; Arai, Keisuke; Miyazawa, Hitomi; Kobayashi, Kyouko; Nakamura, Junpei; Suto, Takayuki; Tsushima, Yoshito

2018-01-01

The simulation study was conducted for the new venous catheter with side holes of contrast-enhanced computed tomography (CT) and magnetic resonance imaging (MRI) to evaluate the infusion pressure on four contrast media and several injection speeds. All infusion pressure of the new venous catheter with side holes were less than 15 kg/cm 2 as limitation of extension tube and also reduced the infusion pressure by 15% at the maximum compared to the catheter with single hole. The results suggest that the new venous catheter with side holes can reduce the infusion pressure by power injection of contrast-enhanced CT and MRI.

Measuring Zonal Transport Variability of the Antarctic Circumpolar Current Using GRACE Ocean Bottom Pressure

Science.gov (United States)

Makowski, J.; Chambers, D. P.; Bonin, J. A.

2012-12-01

Previous studies have suggested that ocean bottom pressure (OBP) can be used to measure the transport variability of the Antarctic Circumpolar Current (ACC). Using OBP data from the JPL ECCO model and the Gravity Recovery and Climate Experiment (GRACE), we examine the zonal transport variability of the ACC integrated between the major fronts between 2003-2010. The JPL ECCO data are used to determine average front positions for the time period studies, as well as where transport is mainly zonal. Statistical analysis will be conducted to determine the uncertainty of the GRACE observations using a simulated data set. We will also begin looking at low frequency changes and how coherent transport variability is from region to region of the ACC. Correlations with bottom pressure south of the ACC and the average basin transports will also be calculated to determine the probability of using bottom pressure south of the ACC as a means for describing the ACC dynamics and transport.

Gaspe hole sets depth record

Energy Technology Data Exchange (ETDEWEB)

1970-03-09

The deepest diamond-cored hole in the Western Hemisphere, Gulf Sunnybank No. 1 on the Gaspe Peninsula of Quebec, has been completed at a depth of 11,600 ft. This is the deepest cored hole to be drilled anywhere in search of oil and gas production, and the deepest to be drilled using a wire-line core recovery technique. The well was completed in 183 days, and was cored continuously below the surface casing which was set and cemented at 1,004 ft. After underreaming a portion of the bottom of the hole, intermediate casing was set and cemented at 8,000 ft as a safety precaution against possible high oil or gas-fluid pressure. Actual coring time, after deducting time for underreaming and casing operations, was 152 days. Because of the cost of transporting a conventional oil-drilling rig to the E. location, the 89-ft mining rig was modified for the project. The contractor was Heath and Sherwood Drilling (Western) Ltd.

High-pressure needle interface for thermoplastic microfluidics.

Science.gov (United States)

Chen, C F; Liu, J; Hromada, L P; Tsao, C W; Chang, C C; DeVoe, D L

2009-01-07

A robust and low dead volume world-to-chip interface for thermoplastic microfluidics has been developed. The high pressure fluidic port employs a stainless steel needle inserted into a mating hole aligned to an embedded microchannel, with an interference fit used to increase pressure resistance. Alternately, a self-tapping threaded needle screwed into a mating hole is also demonstrated. In both cases, the flat bottom needle ports seat directly against the microchannel substrate, ensuring low interfacial dead volumes. Low dispersion is observed for dye bands passing the interfaces. The needle ports offer sufficient pull-out forces for applications such as liquid chromatography that require high internal fluid pressures, with the epoxy-free interfaces compatible with internal microchannel pressures above 40 MPa.

Pressure drop performance evaluation for test assemblies with the newly developed top and bottom nozzles

International Nuclear Information System (INIS)

Lee, S. K.; Park, N. K.; Su, J. M.; Kim, H. K.; Lee, J. N.; Kim, K. T.

2003-01-01

To perform the hydraulic test for the newly developed top and bottom nozzles, two kinds of test assemblies were manufactured i. e. one is the test assembly which has the newly developed top and bottom nozzles and the other is Guardian test assembly which is commercially in mass production now. The test results show that the test assembly with one top nozzle and two bottom nozzles has a greater pressure loss coefficient than Guardian test assembly by 60.9% and 90.4% at the bottom nozzle location. This cause is due to the debris filtering plate for bottom nozzle to improve a filtering efficiency aginst foreign material. In the region of mid grid and top nozzle, there is no difference in pressure loss coefficient between the test assemblies since the componet features in these regions are very similar or same each other. The loss coefficients are 14.2% and 21.9% for model A and B respectively in the scale of test assembly, and the value would be within the 10% in the scale of real fuel assembly. As a result of hydraulic performance evaluation, model A is superior to model B

Method of calculating pilestrip foundations in case of karst hole formation

Directory of Open Access Journals (Sweden)

Gotman Al'fred Leonidovich

2014-02-01

displacements and inner forces in the pile at the level of the hole bottom that are evaluated in turn for the upward and downward pile section. The method of pile analysis is developed in case of lateral soil pressure approximation with the linear function.The method worked out allows recalculating a pile being at the edge of the karst hole and accepting the lateral pressure of the downfallen soil on the hole edges.

Special servicing equipment for reactor pressurized vessel stud hole and stud accessories

International Nuclear Information System (INIS)

Li Jianglian

1999-01-01

The author briefly introduces the design and manufacture of nuclear island special servicing equipment of Nuclear Power Institute of China. Maintenance process of reactor pressurized vessel (RPV) stud hold and stud accessories the special servicing equipment include RPV flange dummy, closed-circuit television (CCTV) inspection equipment, RPV stud hole expandable comb, RPV stud hole polisher, RPV stud hold thread lubricating equipment, RPV stud hole thread miller and RPV stud hole camera. It is presented how eight kinds of special servicing equipment perform the maintenance process concerning their function, structure, and characteristics, their practical use on site is also introduced

Apparatus for inspecting and repairing a pressurized-water reactor's steam generator heat exchanger tubes

International Nuclear Information System (INIS)

Mueller, O.; Roettger, H.; Kasti, H.; Hagen, H.G.

1976-01-01

Described is an apparatus provided for use with a pressurized-water reactor' steam generator having a manifold chamber enclosing the bottom side of a horizontal tube sheet having holes therethrough in which are mounted the tubes of a heat exchanger tube bundle. The manifold chamber has a manhole giving access to the tube's bottom side to permit internal inspection or repair of the tubes by registration of an end of a flexible guide conduit with the tube sheet holes and through which a flexible carrier can be guided for insertion via these holes in the tube sheet and through the tubes extending from the tube sheet's other side

Investigation of High Pressure, Multi-Hole Diesel Fuel Injection Using High Speed Imaging

Science.gov (United States)

Morris, Steven; Eagle, Ethan; Wooldridge, Margaret

2012-10-01

Research to experimentally capture and understand transient fuel spray behavior of modern fuel injection systems remains underdeveloped. To this end, a high-pressure diesel common-rail fuel injector was instrumented in a spherical, constant volume combustion chamber to image the early time history of injection of diesel fuel. The research-geometry fuel injector has four holes aligned on a radial plane of the nozzle with hole sizes of 90, 110, 130 and 150 μm in diameter. Fuel was injected into a non-reacting environment with ambient densities of 17.4, 24.0, and 31.8 kg/m3 at fuel rail pressures of 1000, 1500, and 2000 bar. High speed images of fuel injection were taken using backlighting at 100,000 frames per second (100 kfps) and an image processing algorithm. The experimental results are compared with a one-dimensional fuel-spray model that was historically developed and applied to fuel sprays from single-hole fuel injectors. Fuel spray penetration distance was evaluated as a function of time for the different injector hole diameters, fuel injection pressures and ambient densities. The results show the differences in model predictions and experimental data at early times in the spray development.

The updated bottom up solution applied to atmospheric pressure photoionization and electrospray ionization mass spectrometry

Science.gov (United States)

The Updated Bottom Up Solution (UBUS) was recently applied to atmospheric pressure chemical ionization (APCI) mass spectrometry (MS) of triacylglycerols (TAGs). This report demonstrates that the UBUS applies equally well to atmospheric pressure photoionization (APPI) MS and to electrospray ionizatio...

Ultrasonic level sensors for liquids under high pressure

Science.gov (United States)

Zuckerwar, A. J.; Mazel, D. S.; Hodges, D. Y.

1986-01-01

An ultrasonic level sensor of novel design continuously measures the level of a liquid subjected to a high pressure (up to about 40 MPa), as is sometimes required for the effective transfer of the liquid. The sensor operates as a composite resonator fabricated from a standard high-pressure plug. A flat-bottom hole is machined into the plug along its center line. An ultrasonic transducer is bonded rigidly to the interior surface of the bottom wall, while the exterior surface is in contact with the liquid. Although the bottom wall is designed to satisfy the pressure code, it is still sufficiently thin to permit ready excitation of the axisymmetric plate modes of vibration. The liquid level is measured by a conventional pulse-echo technique. A prototype sensor was tested successfully in a 2300-l water vessel at pressures up to about 37 MPa. A spectral analysis of the transmitted pulse reveals that the flexural, extensional, thickness-shear, and radial plate modes are excited into vibration, but none of these appears to be significantly affected by the pressurization of the liquid.

Debris filtering effectiveness and pressure drop tests of debris resistance-bottom end piece

International Nuclear Information System (INIS)

Chung, Moon Ki; Song, Chul Hwa; Chung, Heung June; Won, Soon Yeun; Cho, Young Ro; Kim, Bok Deuk

1992-03-01

In this final report, described are the test conditions and test procedures for the debris filtering effectiveness and pressure drop tests for developing the Debris Resistance-Bottom End Piece (DR-BEP). And the test results are tabulated for later evaluation. (Author)

Development of automated ultrasonic device for in-service inspection of ABWR pressure vessel bottom head

International Nuclear Information System (INIS)

Kojima, Y.; Matsuyama, A.

1995-01-01

An automated device and its controller have been developed for the bottom head weld examination of pressure vessel of Advanced Boiling Water Reactor (ABWR). The internal pump casings and the housings of control rod prevent a conventional ultrasonic device from scanning the required inspection zone. With this reason, it is required to develop a new device to examine the bottom head area of ABWR. The developed device is characterized by the following features. (1) Composed of a mother vehicle and a compact inspection vehicle. They are connected only by an electric wire without using the conventional arm mechanism. (2) The mother vehicle travels on a track and lift up the inspection vehicle to the vessel. (3) The mother vehicle can automatically attach the inspection vehicle to the bottom head, and detach the inspection vehicle from it. (4) Collision avoidance control function with a touch sensor is installed at the front of the inspection vehicle. The device was successfully demonstrated using a mock-up of reactor pressure vessel

Noise Reduction of Ocean-Bottom Pressure Data Toward Real-Time Tsunami Forecasting

Science.gov (United States)

Tsushima, H.; Hino, R.

2008-12-01

We discuss a method of noise reduction of ocean-bottom pressure data to be fed into the near-field tsunami forecasting scheme proposed by Tsushima et al. [2008a]. In their scheme, the pressure data is processed in real time as follows: (1) removing ocean tide components by subtracting the sea-level variation computed from a theoretical tide model, (2) applying low-pass digital filter to remove high-frequency fluctuation due to seismic waves, and (3) removing DC-offset and linear-trend component to determine a baseline of relative sea level. However, it turns out this simple method is not always successful in extracting tsunami waveforms from the data, when the observed amplitude is ~1cm. For disaster mitigation, accurate forecasting of small tsunamis is important as well as large tsunamis. Since small tsunami events occur frequently, successful tsunami forecasting of those events are critical to obtain public reliance upon tsunami warnings. As a test case, we applied the data-processing described above to the bottom pressure records containing tsunami with amplitude less than 1 cm which was generated by the 2003 Off-Fukushima earthquake occurring in the Japan Trench subduction zone. The observed pressure variation due to the ocean tide is well explained by the calculated tide signals from NAO99Jb model [Matsumoto et al., 2000]. However, the tide components estimated by BAYTAP-G [Tamura et al., 1991] from the pressure data is more appropriate for predicting and removing the ocean tide signals. In the pressure data after removing the tide variations, there remain pressure fluctuations with frequencies ranging from about 0.1 to 1 mHz and with amplitudes around ~10 cm. These fluctuations distort the estimation of zero-level and linear trend to define relative sea-level variation, which is treated as tsunami waveform in the subsequent analysis. Since the linear trend is estimated from the data prior to the origin time of the earthquake, an artificial linear trend is

Correlated electron—hole transitions in wurtzite GaN quantum dots: the effects of strain and hydrostatic pressure

International Nuclear Information System (INIS)

Zheng Dongmei; Wang Zongchi; Xiao Boqi

2012-01-01

Within the effective-mass and finite-height potential barrier approximation, a theoretical study of the effects of strain and hydrostatic pressure on the exciton emission wavelength and electron—hole recombination rate in wurtzite cylindrical GaN/Al x Ga 1−x N quantum dots (QDs) is performed using a variational approach. Numerical results show that the emission wavelength with strain effect is higher than that without strain effect when the QD height is large (> 3.8 nm), but the status is opposite when the QD height is small (< 3.8 nm). The height of GaN QDs must be less than 5.5 nm for an efficient electron—hole recombination process due to the strain effect. The emission wavelength decreases linearly and the electron—hole recombination rate increases almost linearly with applied hydrostatic pressure. The hydrostatic pressure has a remarkable influence on the emission wavelength for large QDs, and has a significant influence on the electron—hole recombination rate for small QDs. Furthermore, the present numerical outcomes are in qualitative agreement with previous experimental findings under zero pressure. (semiconductor physics)

Results of the non-nulling calibration of five-hole pressure probe

Science.gov (United States)

Bereznai, J.; Mlynár, P.; Masaryk, M.

2017-09-01

In the laboratory of the Institute of Energy Machinery, Faculty of Mechanical Engineering in Bratislava were produced amount of pressure probes of different designs. Special position among themselves are five-hole pressure probe with tip of sphere or wedge used to determine the velocity vector in a unknown flow fields. Such probes have to be calibrated during blowing an air stream of known velocity magnitude and components of the velocity vector at different angles of attack, when the characteristic information about pressures on a sensitive part of the measuring probe is obtained.

Preventive protection device and method for bottom of reactor pressure vessel

International Nuclear Information System (INIS)

Hayashi, Eisaku; Kurosawa, Koichi; Furukawa, Hideyasu; Morinaka, Ren; Enomoto, Kunio; Otaka, Masahiro; Yoshikubo, Fujio; Chiba, Noboru; Sato, Kazunori.

1995-01-01

In a preventive protection device for improving stresses in reactor structural components by jetting highly pressurized water with cavitation bubbles from a jetting nozzle toward structural components in a reactor pressure vessel, a fixed structure to a CRD housing is provided with a rotational body attached to the structure, a multi joint arm and a jetting nozzle supported to the multi joint arm. The jetting nozzle is disposed at a position where the center of the jetting deviates from the center of the CRD housing. In addition, a monitoring camera is disposed for displaying the target for preventive protection. The state of stresses on a plurality of targets for preventive protection can be improved by the preventive protection device at a fixed position in the bottom of a reactor pressure vessel where housings stand densely, thereby enabling to attain the preventive protection operation easily and rapidly. (N.H.)

Bottom reflector for power reactors

International Nuclear Information System (INIS)

Elter, C.; Kissel, K.F.; Schoening, J.; Schwiers, H.G.

1982-01-01

In pebble bed reactors erosion and damage due fuel elements movement on the surface of the bottom reflector should be minimized. This can be achieved by chamfering and/or rounding the cover edges of the graphite blocks and the edges between the drilled holes and the surface of the graphite block. (orig.) [de

Electrostatic Analysis of Annular Holes Penetrated by Shorted-Cable

Energy Technology Data Exchange (ETDEWEB)

Choo, Jae Yul; Kim, Hyung Tae; Park, Hyun Shin; Cho, Young Sik [KINS, Daejeon (Korea, Republic of)

2016-05-15

The cabinet has an important role to protect the contained cables and digital modules for the safety function from the external electromagnetic (EM) source. Thus the immunity of an open cabinet against electromagnetic interference (EMI) numerically has been investigated using mode-matching method in. Another path for the external EM source to impinge on inner cables and digital modules is the bottom hole of the cabinet that is penetrated by various cables. Especially the EMI can detrimentally influence on the digital modules through annular space caused by sealing the bottom hole of the cabinet incompletely. Thus it is recently required that the electromagnetic interpretation in the annular hole is performed to remedy electromagnetic problems. Based on the mode-matching method, we solved the electrostatic boundary-value problem for holes penetrating shorted-cable at the bottom of a digital I and C cabinet. The Weber transform and the Hankel transform were applied to formulate the electrostatic potential. The capacitance and potential distribution generated near the penetrating shorted-cable were computed and compared with the result from the previous study.

Welding lines formation in holes obtained by low pressure injection molding of ceramic parts

Directory of Open Access Journals (Sweden)

C. A. Costa

Full Text Available Abstract This work presents a study to evaluate the process of producing internal holes in ceramic disks produced by low pressure injection molding (LPIM process. Two process conditions defined as pre-injection and post-injection were used to test the proposition. In the first one the pin cores that produce the holes were positioned in the cavity before the injection of the feedstock; and in the second one, the pin cores were positioned in the cavity, just after the feeding phase of the injection mold. An experimental injection mold designed and manufactured to test both processes was developed to produce ceramic disk with Ø 50 x 2 mm with four holes of Ø 5 mm, equally and radially distributed through the disk. The feedstock was composed of 86 wt% alumina (Al2O3 and 14 wt% organic vehicle based on paraffin wax. Heating and cooling systems controlled by a data acquisition system were included in the mold. The results showed that there were no welding lines with the post-injection process, proving to be an option for creating holes in the ceramic parts produced by LPIM. It was observed that best results were obtained at 58 °C mold temperature. The pins extraction temperature was about 45 °C, and the injection pressure was 170 kPa.

A Record-High Ocean Bottom Pressure in the South Pacific Observed by GRACE

Science.gov (United States)

Boening, Carmen; Lee, Tong; Zlotnicki, Victor

2011-01-01

In late 2009 to early 2010, the Gravity Recovery and Climate Experiment (GRACE) satellite pair observed a record increase in ocean bottom pressure (OBP) over a large mid-latitude region of the South East Pacific. Its magnitude is substantially larger than other oceanic events in the Southern Hemisphere found in the entire GRACE data records (2003-2010) on multi-month time scales. The OBP data help to understand the nature of a similar signal in sea surface height (SSH) anomaly observed by altimetry: the SSH increase is mainly due to mass convergence. Analysis of the barotropic vorticity equation using scatterometer data, atmospheric reanalysis product, and GRACE and altimeter an atmospheric reanalysis product observations suggests that the observed OBP/SSH signal was primarily caused by wind stress curl associated with a strong and persistent anticyclone in late 2009 in combination with effects of planetary vorticity gradient, bottom topography, and friction

Improvement of Blood Pressure, Glucose Metabolism, and Lipid Profile by the Intake of Powdered Asparagus (蘆筍 Lú Sǔn Bottom-stems and Cladophylls

Directory of Open Access Journals (Sweden)

Mie Nishimura

2013-10-01

Full Text Available Asparagus (蘆筍 Lú Sǔn; Asparagus officinalis L. is a common vegetable, long used as an herbal medicine. The cladophylls and bottom-stems of asparagus have various pharmacological effects, but they are generally discarded at harvesting. The present open clinical trial was performed to examine the effects of the intake of cladophylls and bottom-stems on the improvement of metabolic syndrome characterized by hypertension, hyperglycemia, and dyslipidemia. Twenty-eight healthy volunteers ingested either cladophyll or bottom-stem powder (6 g/day daily for 10 weeks. The cladophyll intake resulted in significant reduction in the subjects’ diastolic blood pressure and fasting plasma glucose (FPG, and decreased both the left cardio-ankle vascular index score and the total cholesterol level (T-CHO. The bottom-stem intake significantly reduced the subjects’ systolic and diastolic blood pressure and FPG as well as T-CHO. These results suggest the possibility that asparagus cladophylls and bottom-stems differentially improve hypertension, hyperglycemia, and dyslipidemia.

Construction of reactor vessel bottom of prestressed reinforced concrete

International Nuclear Information System (INIS)

Sitnikov, M.I.; Metel'skij, V.P.

1980-01-01

Methods are described for building reactor vessel bottoms of prestressed reinforced concrete during NPPs construction in Great Britain, France, Germany (F.R.) and the USA. Schematic of operations performed in succession is presented. Considered are different versions of one of the methods for concreting a space under a facing by forcing concrete through a hole in the facing. The method provides tight sticking of the facing to the reactor vessel bottom concrete

Study on Transfer Rules of Coal Reservoir Pressure Drop Based on Coalbed Methane Well Drainage Experiments

Science.gov (United States)

Yuhang, X.

2017-12-01

A pumping test was carried out to explore the transfer rules of pressure drop in coal reservoir during the drainage. The experiment was divided into three stages. In the first stage, the pump displacement of 3m3/h was used to reduce the bottom hole flowing pressure and stopped until the continuous gas phase was produced; Undertaking the first stage, in the second stage, when the gas phase was continuously produced, the pump was stopped immediately. As the bottom hole flowing pressure going up without gas phase, pumping started again for a week. In the third stage ,the well pumping was carried out at the bottom hole pressure drop rate of 30Kpa/d after two months' recovery. Combined with the data of regional geology and fractured well, taking the characteristics of macroscopic coal rocks, development of pore and fracture in coal and isothermal adsorption test as the background, the features of reservoir output in each stage of the experiment were analyzed and compared, and then the transfer rules of pressure drop contained in the differences of the output was studied further. In the first and third stage of the experiment, the output of liquid phase was much larger than the space volume of coal reservoir pore and fracture in the range of 100m2. In the second stage, the output of the continuous gas phase appeared around 0.7Mpa when the continuous gas phase appears below the critical desorption pressure of 0.25Mpa during the whole experiment. The results indicate that, the transfer of pressure drop in the coal reservoir of this well is mainly horizontal, and the liquid phase produced in the reservoir mainly comes from the recharge of the reservoir at the far end of the relative high pressure area; the adsorption space of coalbed methane in the coal matrix as well as the main migration channel of fluid in the reservoir doesn't belong to the same pressure system and there exists the communication barrier between them. In addition, the increasing of the effective stress

Cascadia Initiative Ocean Bottom Seismograph Performance

Science.gov (United States)

Evers, B.; Aderhold, K.

2017-12-01

The Ocean Bottom Seismograph Instrument Pool (OBSIP) provided instrumentation and operations support for the Cascadia Initiative community experiment. This experiment investigated geophysical processes across the Cascadia subduction zone through a combination of onshore and offshore seismic data. The recovery of Year 4 instruments in September 2015 marked the conclusion of a multi-year experiment that utilized 60 ocean-bottom seismographs (OBSs) specifically designed for the subduction zone boundary, including shallow/deep water deployments and active fisheries. The new instruments featured trawl-resistant enclosures designed by Lamont-Doherty Earth Observatory (LDEO) and Scripps Institution of Oceanography (SIO) for shallow deployment [water depth ≤ 500 m], as well as new deep-water instruments designed by Woods Hole Oceanographic Institute (WHOI). Existing OBSIP instruments were also deployed along the Blanco Transform Fault and on the Gorda Plate through complementary experiments. Station instrumentation included weak and strong motion seismometers, differential pressure gauges (DPG) and absolute pressure gauges (APG). All data collected from the Cascadia, Blanco, and Gorda deployments is available through the Incorporated Research Institutions for Seismology (IRIS) Data Management Center (DMC). The Cascadia Initiative is the largest amphibious seismic experiment undertaken to date, encompassing a diverse technical implementation and demonstrating an effective structure for community experiments. Thus, the results from Cascadia serve as both a technical and operational resource for the development of future community experiments, such as might be contemplated as part of the SZ4D Initiative. To guide future efforts, we investigate and summarize the quality of the Cascadia OBS data using basic metrics such as instrument recovery and more advanced metrics such as noise characteristics through power spectral density analysis. We also use this broad and diverse

Formation of electrostatic double-layers and electron-holes in a low pressure mercury plasma column

International Nuclear Information System (INIS)

Petraconi, G; Maciel, Homero S

2003-01-01

Experimental studies of the formation of electrostatic double layers (DLs) and electron-holes (e-holes) are reported. The measurements were performed in the positive column of a mercury arc discharge operating in the low-pressure range of (2.0-14.0) x 10 -2 Pa with current density in the range of (3.0-8.0) x 10 3 A m -2 . Stable and unstable modes of the discharge were identified as the current was gradually increased, keeping constant the vapour pressure. The discharge remains stable until a critical current from which a slight increase of the current leads to an unstable regime characterized by high discharge impedance and strong oscillations. This mode ceased after a DL was formed in the plasma column. To induce the DL formation and to transport it smoothly along the discharge column, a low intensity B-field (7-10) x 10 -3 T produced by a movable single coil was used. The B-field locally increases the electron current density and makes the DL form at the centre of the magnetic constriction where it remained at rest. Electrostatic potential structures compatible with ordinary DLs and multiple-layers could be formed in the plasma column by dealing with the combined effects of the operational parameters of the discharge. It is noticeable that a pure e-hole, which is a symmetric triple-layer having a bell shape potential profile, could easily be formed by means of this experimental technique. A partial kinetic description, based on the space charge structure derived from an experimental e-hole, is presented in order to infer the charged particle populations that could contribute to the space charge of the e-hole. Evidence is shown that strong e-hole formation might be driven by an ion beam, therefore it could not be formed in isolation since its formation requires a nearby ion accelerating potential structure. Probe measurements of the plasma properties, at various radial positions of the stable positive column, are also presented. In the stable mode, prior to

Effects of High-Pressure Treatment on the Muscle Proteome of Hake by Bottom-Up Proteomics.

Science.gov (United States)

Carrera, Mónica; Fidalgo, Liliana G; Saraiva, Jorge A; Aubourg, Santiago P

2018-05-02

A bottom-up proteomics approach was applied for the study of the effects of high-pressure (HP) treatment on the muscle proteome of fish. The performance of the approach was established for a previous HP treatment (150-450 MPa for 2 min) on frozen (up to 5 months at -10 °C) European hake ( Merluccius merluccius). Concerning possible protein biomarkers of quality changes, a significant degradation after applying a pressure ≥430 MPa could be observed for phosphoglycerate mutase-1, enolase, creatine kinase, fructose bisphosphate aldolase, triosephosphate isomerase, and nucleoside diphosphate kinase; contrary, electrophoretic bands assigned to tropomyosin, glyceraldehyde-3-phosphate dehydrogenase, and beta parvalbumin increased their intensity after applying a pressure ≥430 MPa. This repository of potential protein biomarkers may be very useful for further HP investigations related to fish quality.

Large dynamic range pressure sensor based on two semicircle-holes microstructured fiber.

Science.gov (United States)

Liu, Zhengyong; Htein, Lin; Lee, Kang-Kuen; Lau, Kin-Tak; Tam, Hwa-Yaw

2018-01-08

This paper presents a sensitive and large dynamic range pressure sensor based on a novel birefringence microstructured optical fiber (MOF) deployed in a Sagnac interferometer configuration. The MOF has two large semicircle holes in the cladding and a rectangular strut with germanium-doped core in the center. The fiber structure permits surrounding pressure to induce large effective index difference between the two polarized modes. The calculated and measured group birefringence of the fiber are 1.49 × 10 -4 , 1.23 × 10 -4 , respectively, at the wavelength of 1550 nm. Experimental results shown that the pressure sensitivity of the sensor varied from 45,000 pm/MPa to 50,000 pm/MPa, and minimum detectable pressure of 80 Pa and dynamic range of better than 116 dB could be achieved with the novel fiber sensor. The proposed sensor could be used in harsh environment and is an ideal candidate for downhole applications where high pressure measurement at elevated temperature up to 250 °C is needed.

Filling bore-holes with explosive

Energy Technology Data Exchange (ETDEWEB)

Alfredsson, S H

1965-03-02

In this device for filling boreholes formed in a rock formation with particulate explosive, the explosive is conveyed into the hole by means of a pressure fluid through a tube which has a lesser diameter than the hole. The tube is characterized by a lattice work arranged externally on it, and having a structure adapted to allow passage of a pressure fluid returning between the tube and the wall of the hole, but retaining particles of explosive entrained by the returning pressure fluid. In another arrangement of the device, the lattice work has the form of a brush, including filaments or bristles which are dimensioned to bridge the spacing between the tube and the wall of the hole. (12 claims)

A Novel Thermal-Mechanical Detection System for Reactor Pressure Vessel Bottom Failure Monitoring in Severe Accidents

International Nuclear Information System (INIS)

Bi, Daowei; Bu, Jiangtao; Xu, Dongling

2013-06-01

Following the Fukushima Daiichi nuclear accident in Japan, there is an increased need of enhanced capabilities for severe accident management (SAM) program. Among others, a reliable method for detecting reactor pressure vessel (RPV) bottom failure has been evaluated as imperative by many utility owners. Though radiation and/or temperature measurement are potential solutions by tradition, there are some limitations for them to function desirably in such severe accident as that in Japan. To provide reliable information for assessment of accident progress in SAM program, in this paper we propose a novel thermal-mechanical detection system (TMDS) for RPV bottom failure monitoring in severe accidents. The main components of TMDS include thermally sensitive element, metallic cables, tension controlled switch and main control room annunciation device. With TMDS installed, there shall be a reliable means of keeping SAM decision-makers informed whether the RPV bottom has indeed failed. Such assurance definitely guarantees enhancement of severe accident management performance and significantly improve nuclear safety and thus protect the society and people. (authors)

Pressing technology for large bottoms

International Nuclear Information System (INIS)

Jilek, L.

1986-01-01

The technology has been selected of a circular plate bent into the shape of a trough, for pressing bottoms of pressure vessels from a circular plate of large diameter. The initial sheet is first bent in the middle by heating with the edges remaining straight. These are then welded longitudinally by electroslag welding and the circular shape is flame cut. The result will be a plate with a straight surface in the middle with raised edges which may be pressed into the desired shape. In this manner it is also possible to press pressure vessel bottoms with tube couplings from plates which are thickened in the middle and drilled; additional welding is then eliminated. Deformation from heat treatment may be avoided by the use of a fixture in the shape of a ring with a groove into which is fixed the edge of the bottom. During hardening of the bottom it will be necessary to care for the withdrawal of vapours and gases which would hamper uniform cooling. Bottom hardening with the grill and the cupola downwards has been proven. Deformation which occurs during treatment may to a certain extent be removed by calibration which cannot, however, be made without special fixtures and instruments. (J.B.)

Hydrodynamics of the Fluid Filtrate on Drilling-In

Science.gov (United States)

Abbasov, É. M.; Agaeva, N. A.

2014-01-01

The volume of the liquid penetrating into the formation after drilling-in has been determined on the basis of theoretical investigations. The dynamics of change in the bottom-hole pressure has been determined in this process. It has been shown that because of the water hammer, the bottom-hole pressure can be doubled in the presence of large fractures and pores closer to the well-bottom zone.

Measuring device for water quality at reactor bottom

Energy Technology Data Exchange (ETDEWEB)

Urata, Hidehiro; Takagi, Jun-ichi

1995-10-27

The present invention concerns measurement for water quality at the bottom of a reactor of a BWR type plant, in which reactor water is sampled and analyzed in a state approximate to conditions in a pressure vessel. Based on the result, hydrogen injection amount is controlled during hydrogen injection operation. Namely, a monitor for water quality is disposed to a sampling line in communication with the bottom of a pressure vessel. A water quality monitor is disposed to a drain sampling line in communication with the bottom of the pressure vessel. A corrosion potentiometer is disposed to the pressure sampling line or the drain sampling line. A dissolved oxygen measuring device is disposed to the pressure vessel sampling line or the drain sampling line. With such a constitution, the reactor water can be sampled and analyzed in a state approximate to the conditions in the pressure vessel. In addition, signals from the water quality monitor are inputted to a hydrogen injection amount control device. As a result, the amount of hydrogen injected to primary coolants can be controlled in a state approximate to the conditions in the pressure vessel. (I.S.).

Measuring device for water quality at reactor bottom

International Nuclear Information System (INIS)

Urata, Hidehiro; Takagi, Jun-ichi.

1995-01-01

The present invention concerns measurement for water quality at the bottom of a reactor of a BWR type plant, in which reactor water is sampled and analyzed in a state approximate to conditions in a pressure vessel. Based on the result, hydrogen injection amount is controlled during hydrogen injection operation. Namely, a monitor for water quality is disposed to a sampling line in communication with the bottom of a pressure vessel. A water quality monitor is disposed to a drain sampling line in communication with the bottom of the pressure vessel. A corrosion potentiometer is disposed to the pressure sampling line or the drain sampling line. A dissolved oxygen measuring device is disposed to the pressure vessel sampling line or the drain sampling line. With such a constitution, the reactor water can be sampled and analyzed in a state approximate to the conditions in the pressure vessel. In addition, signals from the water quality monitor are inputted to a hydrogen injection amount control device. As a result, the amount of hydrogen injected to primary coolants can be controlled in a state approximate to the conditions in the pressure vessel. (I.S.)

Hole history, rotary hole DC-3

International Nuclear Information System (INIS)

1977-10-01

Purpose of hole DC-3 was to drill into the Umtanum basalt flow using both conventional rotary and core drilling methods. The borehole is to be utilized for geophysical logging, future hydrological testing, and the future installation of a borehole laboratory for long-term pressure, seismic, and moisture migration or accumulation recording in the Umtanum basalt flow in support of the Basalt Waste Isolation Program. Hole DC-3 is located east of the 200 West barricaded area on the Hanford reservation

Electron-hole transition in spherical QD-QW nanoparticles based on GaN∣(In,Ga)N∣GaN under hydrostatic pressure

International Nuclear Information System (INIS)

El Ghazi, Haddou; Jorio, Anouar

2013-01-01

Within the framework of effective-mass approximation and finite parabolic potential confinement barrier in which two confinement parameters are taking account, the electron (hole) energy and the ground-state electron-hole (e−h) transition in Core∣well∣shell (GaN|In x Ga 1−x N|GaN) spherical QD-QW nanoparticles are investigated as a function of the inner and the outer radii under externally applied hydrostatic pressure. The pressure dependencies of the effective-mass and the QD radius are taking into account. The results we obtained are in quite good agreement with the theoretical and the experimental findings

Electron-hole transition in spherical QD-QW nanoparticles based on GaN∣(In,Ga)N∣GaN under hydrostatic pressure

Energy Technology Data Exchange (ETDEWEB)

El Ghazi, Haddou, E-mail: hadghazi@gmail.com [LPS, Faculty of Science, Dhar EL Mehrez, BP 1796 Fes-Atlas (Morocco); Special Mathematics, CPGE Kénitra, Chakib Arsalane Street (Morocco); Jorio, Anouar [LPS, Faculty of Science, Dhar EL Mehrez, BP 1796 Fes-Atlas (Morocco)

2013-11-15

Within the framework of effective-mass approximation and finite parabolic potential confinement barrier in which two confinement parameters are taking account, the electron (hole) energy and the ground-state electron-hole (e−h) transition in Core∣well∣shell (GaN|In{sub x}Ga{sub 1−x}N|GaN) spherical QD-QW nanoparticles are investigated as a function of the inner and the outer radii under externally applied hydrostatic pressure. The pressure dependencies of the effective-mass and the QD radius are taking into account. The results we obtained are in quite good agreement with the theoretical and the experimental findings.

Effect of water flow rate and water chemistry on corrosion environment in reactor pressure vessel bottom of BWRs

Energy Technology Data Exchange (ETDEWEB)

Ichikawa, Nagayoshi; Hemmi, Yukio; Takagi, Junichi; Urata, Hidehiro [Toshiba Corp., Kawasaki, Kanagawa (Japan)

1999-07-01

To evaluate the corrosion environment at the bottom of the reactor pressure vessel in a BWR and the effect of hydrogen water chemistry on the corrosion of materials in the region, measurements of the corrosion potential of Type-304 stainless steel and nickel base alloy were made in a laboratory test loop. The effect of water chemistry on the corrosion potential of nickel base alloy is found to be similar to the effect on Type-304 stainless steel. Flow analysis and precise evaluations of the corrosion potential of materials in the bottom region were implemented. Corrosion potentials throughout the region were evaluated from the flow analysis results. At the jet pump outlet and shroud support leg, a rather large amount of hydrogen had to be added to reduce the potential. Conversely, a small amount of hydrogen was enough in the case of the stub tube of the control rod drive guide tubing and the ICM housings located in the center of the bottom region. (author)

Effect of water flow rate and water chemistry on corrosion environment in reactor pressure vessel bottom of BWRs

International Nuclear Information System (INIS)

Ichikawa, Nagayoshi; Hemmi, Yukio; Takagi, Junichi; Urata, Hidehiro

1999-01-01

To evaluate the corrosion environment at the bottom of the reactor pressure vessel in a BWR and the effect of hydrogen water chemistry on the corrosion of materials in the region, measurements of the corrosion potential of Type-304 stainless steel and nickel base alloy were made in a laboratory test loop. The effect of water chemistry on the corrosion potential of nickel base alloy is found to be similar to the effect on Type-304 stainless steel. Flow analysis and precise evaluations of the corrosion potential of materials in the bottom region were implemented. Corrosion potentials throughout the region were evaluated from the flow analysis results. At the jet pump outlet and shroud support leg, a rather large amount of hydrogen had to be added to reduce the potential. Conversely, a small amount of hydrogen was enough in the case of the stub tube of the control rod drive guide tubing and the ICM housings located in the center of the bottom region. (author)

Constructing bottom barriers with met grouting

International Nuclear Information System (INIS)

Shibazaki, M.; Yoshida, H.

1997-01-01

Installing a bottom barrier using conventional high pressure jetting technology and ensuring barrier continuity is challenging. This paper describes technology that has been developed and demonstrated for the emplacement of bottom barriers using pressures and flow rates above the conventional high pressure jetting parameters. The innovation capable of creating an improved body exceeding 5 meters in diameter has resulted in the satisfying connection and adherence between the treated columns. Besides, the interfaces among the improved bodies obtain the same strength and permeability lower than 1 x 10 -7 cm/sec as body itself. A wide variety of the thickness and the diameter of the improved mass optimizes the application, and the method is nearing completion. The paper explains an aspect and briefs case histories

Ultrasonic test results for the reactor pressure vessel of the HTTR. Longitudinal welding line of bottom dome

International Nuclear Information System (INIS)

Nojiri, Naoki; Ohwada, Hiroyuki; Kato, Yasushi

2008-06-01

This paper describes the inspection method, the measured area, etc. of the ultrasonic test of the in-service inspection (ISI) for welding lines of the reactor pressure vessel of the HTTR and the inspection results of the longitudinal welding line of the bottom dome. The pre-service inspection (PSI) results for estimation of occurrence and progression of defects to compare the ISI results is described also. (author)

Simultaneous effects of electron-hole correlation, hydrostatic pressure, and temperature on the third harmonic generation in parabolic GaAs quantum dots

International Nuclear Information System (INIS)

Duque, C. M.; Mora-Ramos, M. E.; Duque, C. A.

2011-01-01

The combined effects of electron-hole correlation, hydrostatic pressure, and temperature on the third harmonic generation in disk-shaped parabolic GaAs quantum dots are studied under the density matrix formalism and the effective mass approximation. Two well-defined regimes are discussed: (1) the strong-confinement regime, where the Coulomb interaction between the electron and hole is neglected and (2) the weak-confinement regime where the parabolic confinement term is neglected and the system reaches the limit of a hydrogenic problem. The results show that the third harmonic-generation coefficient is strongly dependent on the localization of the electron-hole pair. Also, that by using external perturbations like hydrostatic pressure or by considering the temperature effects it is possible to induce a blue-shift and/or red-shift on the resonant peaks of the third harmonic generation coefficient.

Primary black holes

International Nuclear Information System (INIS)

Novikov, I.; Polnarev, A.

1981-01-01

Proves are searched for of the formation of the so-called primary black holes at the very origin of the universe. The black holes would weigh less than 10 13 kg. The formation of a primary black hole is conditional on strong fluctuations of the gravitational field corresponding roughly to a half of the fluctuation maximally permissible by the general relativity theory. Only big fluctuations of the gravitational field can overcome the forces of the hot gas pressure and compress the originally expanding matter into a black hole. Low-mass black holes have a temperature exceeding that of the black holes formed from stars. A quantum process of particle formation, the so-called evaporation takes place in the strong gravitational field of a black hole. The lower the mass of the black hole, the shorter the evaporation time. The analyses of processes taking place during the evaporation of low-mass primary black holes show that only a very small proportion of the total mass of the matter in the universe could turn into primary black holes. (M.D.)

Ocean-bottom pressure changes above a fault area for tsunami excitation and propagation observed by a submarine dense network

Science.gov (United States)

Yomogida, K.; Saito, T.

2017-12-01

Conventional tsunami excitation and propagation have been formulated by incompressible fluid with velocity components. This approach is valid in most cases because we usually analyze tunamis as "long gravity waves" excited by submarine earthquakes. Newly developed ocean-bottom tsunami networks such as S-net and DONET have dramatically changed the above situation for the following two reasons: (1) tsunami propagations are now directly observed in a 2-D array manner without being suffered by complex "site effects" of sea shore, and (2) initial tsunami features can be directly detected just above a fault area. Removing the incompressibility assumption of sea water, we have formulated a new representation of tsunami excitation based on not velocity but displacement components. As a result, not only dynamics but static term (i.e., the component of zero frequency) can be naturally introduced, which is important for the pressure observed on the ocean floor, which ocean-bottom tsunami stations are going to record. The acceleration on the ocean floor should be combined with the conventional tsunami height (that is, the deformation of the sea level above a given station) in the measurement of ocean-bottom pressure although the acceleration exists only during fault motions in time. The M7.2 Off Fukushima earthquake on 22 November 2016 was the first event that excited large tsunamis within the territory of S-net stations. The propagation of tsunamis is found to be highly non-uniform, because of the strong velocity (i.e., sea depth) gradient perpendicular to the axis of Japan Trench. The earthquake was located in a shallow sea close to the coast, so that all the tsunami energy is reflected by the trench region of high velocity. Tsunami records (pressure gauges) within its fault area recorded clear slow motions of tsunamis (i.e., sea level changes) but also large high-frequency signals, as predicted by our theoretical result. That is, it may be difficult to extract tsunami

Bursting Events in Pressure Flushing with Expanding Bottom Outlet Channel within Dam Reservoir

Directory of Open Access Journals (Sweden)

soheila Tofighi

2017-01-01

Full Text Available Introduction: Currently, large dams in the world, due to the high amount of sediments in the reservoir, especially around the intake, have operational problems. One of the solutions for this problem is pressure flushing. In this type of flushing, a mixture of water and sediment is removed from bottom outlets form dam reservoir and a funnel shaped crater is created in the vicinity of the outlet opening. In laboratory experiments carried out in this study, pressure flushing with the expansion of bottom outlet within the reservoir and its statistical analysis of bursting events were investigated. The structure of the turbulent flow is not fully understood due to their complexity and random nature. Klein et al. Introduced the turbulence bursting in this kind of flow and Nezo and Nakagora suggested that the events resulting from turbulence bursting has a significant effect of transferring the sediment particles. Materials and Methods: For the purposes of this study, the experiments were conducted with a physical model with 7m length, 1.4m width, and 1.5m height, consisting of three parts namely the inlet of the model, the main reservoir, and settling basin. The main reservoir of the model was 5m long and the sediments were placed within this part of the model. The sediment particles were non-cohesive silica with uniform size and with median diameter (d50 1.15mm and geometrics standard deviation (σg 1.37. Experiments carried out with different discharges and water depths above the bottom outlet in different expansion size of outlet channel in constant sediment level of 20cm above the center of the outlet channel. The model was slowly filled with water until the water surface elevation reached to a desired level. The bottom outlet was manually opened, after a while sedimentwere discharged with the water flow in very high concentrations through the outlet channel (sudden discharge and a funnel shaped crater was formed in front of it. After the run of

High pressure fracturing in Colombia: a quantum leap

Energy Technology Data Exchange (ETDEWEB)

Velasquez, Juan C. [BP Exploration (United Kingdom); Gutierrez, Jim; Ham, Ernesto; Castro, Alberto [BJ Services Company (United States)

2004-07-01

Fracturing has become one of the most common stimulation and well completion techniques in petroleum production. Due to the deeper depths and high frac gradients encountered in some areas, various treatments have resulted in early screen outs or aborted operations due to insufficient rate limited by the available treating pressures. A state of the art technology and high pressure equipment including the largest frac pumps (rated at 2,700 hhp) in the world, were used in Colombian fields to overcome these limitations. The reliability of this equipment has allowed the treatment of these wells to operating pressures of up to 18,000 psi and rates in excess of 40 bpm, placing up to 400,000 lbs of bauxite. Bottom hole treating pressures of 25,000 psi also were reached. This paper describes the development of the fracture campaign and relates the jobs performed to date, including the results and lessons learned (author)

Stability of black holes based on horizon thermodynamics

Directory of Open Access Journals (Sweden)

Meng-Sen Ma

2015-12-01

Full Text Available On the basis of horizon thermodynamics we study the thermodynamic stability of black holes constructed in general relativity and Gauss–Bonnet gravity. In the framework of horizon thermodynamics there are only five thermodynamic variables E, P, V, T, S. It is not necessary to consider concrete matter fields, which may contribute to the pressure of black hole thermodynamic system. In non-vacuum cases, we can derive the equation of state, P=P(V,T. According to the requirements of stable equilibrium in conventional thermodynamics, we start from these thermodynamic variables to calculate the heat capacity at constant pressure and Gibbs free energy and analyze the local and global thermodynamic stability of black holes. It is shown that P>0 is the necessary condition for black holes in general relativity to be thermodynamically stable, however this condition cannot be satisfied by many black holes in general relativity. For black hole in Gauss–Bonnet gravity negative pressure can be feasible, but only local stable black hole exists in this case.

Hole geometry effect on stop-band characteristics of photonic crystal in Ti-diffused LiNbO_3 waveguide

International Nuclear Information System (INIS)

Zhao, Quan-Zhou; Zhang, Zi-Bo; Xu, Jia-Qi; Wong, Wing-Han; Yu, Dao-Yin; Pun, Edwin Yue-Bun

2017-01-01

Effects of finite hole depth and non-cylindrical hole shape on stop-band characteristics of photonic crystal formed by air-hole square lattice in Ti-diffused LiNbO_3 strip waveguide were studied theoretically. The study shows that hole depth determines the contrast of stop-band, and the hole radius and conical angle determine the bandgap and location. Cylindrical holes must be sufficiently deep so as to overlap most of waveguide mode and hence obtain a stop-band with high contrast, sharp edge and broad bandgap. Non-cylindrical holes seriously affect the stop-band features. Conical holes cause low contrast and narrow bandgap, and the stop-band shifts with the conical angle. For the cylindrical-conical hybrid holes, the cylindrical portion determines the desired features. Given the difficulty in fabricating high aspect-ratio cylindrical holes, we propose to fabricate the holes at the bottom of a shallow trench, which is introduced into waveguide surface prior to the hole milling. - Highlights: • Cylindrical hole must be deep enough and a shallow waveguide is required. • Increasing hole radius causes blueshift, broadening and edge sharpening of band. • Non-cylindrical hole seriously affects gap, location and contrast of stop-band. • For cylindrical-conical hybrid hole, cylindrical part determines desired features. • A scheme of milling holes at bottom of a trench on waveguide surface is proposed.

Fabrication of PDMS through-holes using the MIMIC method and the surface treatment by atmospheric-pressure CH4/He RF plasma

Science.gov (United States)

Choi, Jongchan; Lee, Kyeong-Hwan; Yang, Sung

2011-09-01

This note presents a simple fabrication process for patterning micro through-holes in a PDMS layer by a combination of the micromolding in capillaries (MIMIC) method and the surface treatment by atmospheric-pressure CH4/He RF plasma. The fabrication process is confirmed by forming micro through-holes with various shapes including circle, C-shape, open microfluidic channel and hemisphere. All micro through-holes of various shapes in a wide range of diameters and heights are well fabricated by the proposed method. Also, a 3D micromixer containing a PDMS micro through-hole layer formed by the proposed method is built and its performance is tested as another practical demonstration of the proposed fabrication method. Therefore, we believe that the proposed fabrication process will build a PDMS micro through-hole layer in a simple and easy way and will contribute to developing highly efficient multi-layered microfluidic systems, which may require PDMS micro through-hole layers.

Tsunami simulation method initiated from waveforms observed by ocean bottom pressure sensors for real-time tsunami forecast; Applied for 2011 Tohoku Tsunami

Science.gov (United States)

Tanioka, Yuichiro

2017-04-01

After tsunami disaster due to the 2011 Tohoku-oki great earthquake, improvement of the tsunami forecast has been an urgent issue in Japan. National Institute of Disaster Prevention is installing a cable network system of earthquake and tsunami observation (S-NET) at the ocean bottom along the Japan and Kurile trench. This cable system includes 125 pressure sensors (tsunami meters) which are separated by 30 km. Along the Nankai trough, JAMSTEC already installed and operated the cable network system of seismometers and pressure sensors (DONET and DONET2). Those systems are the most dense observation network systems on top of source areas of great underthrust earthquakes in the world. Real-time tsunami forecast has depended on estimation of earthquake parameters, such as epicenter, depth, and magnitude of earthquakes. Recently, tsunami forecast method has been developed using the estimation of tsunami source from tsunami waveforms observed at the ocean bottom pressure sensors. However, when we have many pressure sensors separated by 30km on top of the source area, we do not need to estimate the tsunami source or earthquake source to compute tsunami. Instead, we can initiate a tsunami simulation from those dense tsunami observed data. Observed tsunami height differences with a time interval at the ocean bottom pressure sensors separated by 30 km were used to estimate tsunami height distribution at a particular time. In our new method, tsunami numerical simulation was initiated from those estimated tsunami height distribution. In this paper, the above method is improved and applied for the tsunami generated by the 2011 Tohoku-oki great earthquake. Tsunami source model of the 2011 Tohoku-oki great earthquake estimated using observed tsunami waveforms, coseimic deformation observed by GPS and ocean bottom sensors by Gusman et al. (2012) is used in this study. The ocean surface deformation is computed from the source model and used as an initial condition of tsunami

Certain possible causes of between shaft gas seepage in gas wells

Energy Technology Data Exchange (ETDEWEB)

Shikhmamedov, N.S.

1981-01-01

Investigations for casing wells are carried out at the Turkmen branch of VNIIgaz (All Union petroleum and Gas Research Institute). The presence of high bottom hole pressure that affects further development of wells was established. Thus, for example, at the Shatlyk formation bottom hole pressures reach 138/sup 0/, and the temperature of the gas at the well head - 106/sup 0/C. Because of the heating process, the casing tubes lengthen, and as a result the euqipment at the well head is raised. Thus, at wells 42 and 312 the height of equipment's rise reaches 12 and 15 cm. respectively. Due to high bottom hole pressure temperatures grouting cement is necessary, one composed of 85% cement and 15% clay powder with a water-cement factor of up to 0.9, and density 1.57-1.60 g/cm/sup 3/. The necessity to create prelimnary casing tube tension was noted. The heated casing tubes must not be cooled during well damping. Wells with high gas temperature and presence of packer at bottom hole should have temperature elongation compensators.

Hole geometry effect on stop-band characteristics of photonic crystal in Ti-diffused LiNbO{sub 3} waveguide

Energy Technology Data Exchange (ETDEWEB)

Zhao, Quan-Zhou [Department of Opto-electronics and Information Engineering, School of Precision Instruments and Opto-electronics Engineering, Tianjin University, Tianjin 300072 (China); Key Laboratory of Optoelectronic Information Technology (Ministry of Education), Tianjin University, Tianjin 300072 (China); School of Physics and Electronic Engineering, University of Shanxi Datong, Datong 037009 (China); Zhang, Zi-Bo [University of Toulouse 3, Faculty of Engineering, 118 Route de Narbonne, F-31062 Toulouse (France); Xu, Jia-Qi [Department of Opto-electronics and Information Engineering, School of Precision Instruments and Opto-electronics Engineering, Tianjin University, Tianjin 300072 (China); Key Laboratory of Optoelectronic Information Technology (Ministry of Education), Tianjin University, Tianjin 300072 (China); Wong, Wing-Han, E-mail: eewhwong@cityu.edu.hk [Department of Opto-electronics and Information Engineering, School of Precision Instruments and Opto-electronics Engineering, Tianjin University, Tianjin 300072 (China); Key Laboratory of Optoelectronic Information Technology (Ministry of Education), Tianjin University, Tianjin 300072 (China); Department of Electronic Engineering and State Key Laboratory of Millimeter Waves, City University of Hong Kong, 83 Tat Chee Avenue, Kowloon, Hong Kong (China); Yu, Dao-Yin [Department of Opto-electronics and Information Engineering, School of Precision Instruments and Opto-electronics Engineering, Tianjin University, Tianjin 300072 (China); Key Laboratory of Optoelectronic Information Technology (Ministry of Education), Tianjin University, Tianjin 300072 (China); Pun, Edwin Yue-Bun [Department of Electronic Engineering and State Key Laboratory of Millimeter Waves, City University of Hong Kong, 83 Tat Chee Avenue, Kowloon, Hong Kong (China); and others

2017-01-15

Effects of finite hole depth and non-cylindrical hole shape on stop-band characteristics of photonic crystal formed by air-hole square lattice in Ti-diffused LiNbO{sub 3} strip waveguide were studied theoretically. The study shows that hole depth determines the contrast of stop-band, and the hole radius and conical angle determine the bandgap and location. Cylindrical holes must be sufficiently deep so as to overlap most of waveguide mode and hence obtain a stop-band with high contrast, sharp edge and broad bandgap. Non-cylindrical holes seriously affect the stop-band features. Conical holes cause low contrast and narrow bandgap, and the stop-band shifts with the conical angle. For the cylindrical-conical hybrid holes, the cylindrical portion determines the desired features. Given the difficulty in fabricating high aspect-ratio cylindrical holes, we propose to fabricate the holes at the bottom of a shallow trench, which is introduced into waveguide surface prior to the hole milling. - Highlights: • Cylindrical hole must be deep enough and a shallow waveguide is required. • Increasing hole radius causes blueshift, broadening and edge sharpening of band. • Non-cylindrical hole seriously affects gap, location and contrast of stop-band. • For cylindrical-conical hybrid hole, cylindrical part determines desired features. • A scheme of milling holes at bottom of a trench on waveguide surface is proposed.

Grumblings from an Awakening Black Hole

Science.gov (United States)

Kohler, Susanna

2015-11-01

In June of this year, after nearly three decades of sleep, the black hole V404 Cygni woke up and began grumbling. Scientists across the globe scrambled to observe the sudden flaring activity coming from this previously peaceful black hole. And now were getting the first descriptions of what weve learned from V404 Cygs awakening!Sudden OutburstV404 Cyg is a black hole of roughly nine solar masses, and its in a binary system with a low-mass star. The black hole pulls a stream of gas from the star, which then spirals in around the black hole, forming an accretion disk. Sometimes the material simply accumulates in the disk but every two or three decades, the build-up of gas suddenly rushes toward the black hole as if a dam were bursting.The sudden accretion in these events causes outbursts of activity from the black hole, its flaring easily visible to us. The last time V404 Cyg exhibited such activity was in 1989, and its been rather quiet since then. Our telescopes are of course much more powerful and sensitive now, nearly three decades later so when the black hole woke up and began flaring in June, scientists were delighted at the chance to observe it.The high variability of V404 Cyg is evident in this example set of spectra, where time increases from the bottom panel to the top. [King et al. 2015]Led by Ashley King (Einstein Fellow at Stanford University), a team of scientists observed V404 Cyg with the Chandra X-ray Observatory, obtaining spectra of the black hole during its outbursts. The black hole flared so brightly during its activity that the team had to take precautions to protect the CCDs in their detector from radiation damage! Now the group has released the first results from their analysis.Windy DiskThe primary surprise from V404 Cyg is its winds. Many stellar-mass black holes have outflows of mass, either in the form of directed jets emitted from their centers, or in the form of high-energy winds isotropically emitted from their accretion disks. But V404

Noise generated by cavitating single-hole and multi-hole orifices in a water pipe

NARCIS (Netherlands)

Testud, P.; Moussou, P.; Hirschberg, A.; Aurégan, Y.

2007-01-01

This paper presents an experimental study of the acoustical effects of cavitation caused by a water flow through an orifice. A circular-centered single-hole orifice and a multi-hole orifice are tested. Experiments are performed under industrial conditions: the pressure drop across the orifice varies

Application of fine managed pressure drilling technique in complex wells with both blowout and lost circulation risks

Directory of Open Access Journals (Sweden)

Ling Yan

2015-03-01

Full Text Available Fractured carbonate reservoirs are susceptible to blowout and lost circulation during drilling, which not only restricts drilling speed, but also poses big threat to well control. Moreover, there are few technical means available to reconstruct pressure balance in the borehole. Accordingly, the fine managed pressure drilling was used in the drilling of Well GS19 in the Qixia Formation with super-high pressure and narrow density window, which is a success: ① back pressure in the annular spaces will be adjusted to maintain a slightly over-balanced bottom-hole hydraulic pressure, and fluid level in the circulation tank will be kept in a slight dropping state to ensure that natural gas in the formation would not invade into the borehole in a massive volume; ② inlet drilling fluid density will be controlled at around 2.35 g/cm3, back pressures in the annular be maintained at 2–5 MPa, and bottom-hole pressure equivalent circulation density be controlled at 2.46–2.52 g/cm3; ③ during managed pressure drilling operations, if wellhead pressure exceeds or expects to exceed 7 MPa, semi-blind rams will be closed. Fluids will pass through the choke manifold of the rig to the choke manifold specifically for pressure control before entering gas/liquid separators to discharge gas; ④ during tripping back pressure will be kept at less than 5 MPa, volume of injected drilling fluid will be higher than the theoretical volume during tripping out, whereas the volume of returned drilling fluid will be higher than the theoretical volume during the out-tripping. This technique has been applied successfully in the drilling of the Qixia Formation, Liangshan Formation and Longmaxi Formation with a total footage of 216.60 m, as a good attempt in complicated wells with both blowout and lost circulation risks, which can provide valuable experiences and guidance for handling similar complexities in the future.

Application of Confined Blasting in Water-Filled Deep Holes to Control Strong Rock Pressure in Hard Rock Mines

Directory of Open Access Journals (Sweden)

Jingxuan Yang

2017-11-01

Full Text Available In extra-thick coal seams, mining operations can lead to large-scale disturbances, complex overburden structures, and frequent and strong strata behavior in the stope, which are serious threats to mine safety. This study analyzed the overburden structure and strata behavior and proposed the technique of confined blasting in water-filled deep holes as a measure to prevent strong rock pressure. It found that there are two primary reasons for the high effectiveness of the proposed technique in presplitting hard coal and rock. First, the fracture water enables much more efficient transfer of dynamic load due to its incompressibility. Second, the subsequent expansion of water can further split the rock by compression. A mechanical model was used to reveal how the process of confined blasting in water-filled deep holes presplit roof. Moreover, practical implementation of this technique was found to improve the structure of hard, thick roof and prevent strong rock pressure, demonstrating its effectiveness in roof control.

Ocean Bottom Seismograph Performance during the Cascadia Initiative

Science.gov (United States)

Aderhold, K.; Evers, B.

2015-12-01

The Ocean Bottom Seismograph Instrument Pool (OBSIP) provides instrumentation and operations support for the Cascadia Initiative community experiment. This experiment investigates geophysical processes across the Cascadia subduction zone through a combination of onshore and offshore seismic data. The recovery of Year 4 instruments in September 2015 marks the conclusion of a multi-year experiment that utilized 60 ocean-bottom seismographs (OBSs) specifically designed for the subduction zone boundary, including shallow/deep water deployments and active fisheries. The new instruments feature trawl-resistant enclosures designed by Lamont-Doherty Earth Observatory (LDEO) and Scripps Institution of Oceanography (SIO) for shallow deployment [water depth ≤ 500 m], as well as new deep-water instruments designed by Woods Hole Oceanographic Institute (WHOI). Existing OBSIP instruments were also deployed along the Blanco Transform Fault and on the Gorda Plate through complementary experiments. Stations include differential pressure gauges (DPG) and absolute pressure gauges (APG). All data collected from the Cascadia, Blanco, and Gorda deployments will be freely available through the Incorporated Research Institutions for Seismology (IRIS) Data Management Center (DMC). The Cascadia Initiative is the largest amphibious seismic experiment undertaken to date and demonstrates an effective structure for community experiments through collaborative efforts from the Cascadia Initiative Expedition Team (CIET), OBSIP (institutional instrument contributors [LDEO, SIO, WHOI] and Management Office [IRIS]), and the IRIS DMC. The successes and lessons from Cascadia are a vital resource for the development of a Subduction Zone Observatory (SZO). To guide future efforts, we investigate the quality of the Cascadia OBS data using basic metrics such as instrument recovery and more advanced metrics such as noise characteristics through power spectral density analysis. We also use this broad and

Mixture distribution in a multi-valve twin-spark ignition engine equipped with high-pressure multi-hole injectors

International Nuclear Information System (INIS)

Mitroglou, N; Arcoumanis, C; Mori, K; Motoyama, Y

2006-01-01

Laser-induced fluorescence has been mainly used to characterise the two-dimensional fuel vapour concentration inside the cylinder of a multi-valve twin-spark ignition engine equipped with high-pressure multi-hole injectors. The effects of injection timing, in-cylinder charge motion and injector tip layout have been quantified. The flexibility in nozzle design of the multi-hole injectors has proven to be a powerful tool in terms of matching overall spray cone angle and number of holes to specific engine configurations. Injection timing was found to control spray impingement on the piston and cylinder wall, thus contributing to quick and efficient fuel evaporation. It was confirmed that in-cylinder charge motion plays a major role in engine's stable operation by assisting in the transportation of the air-fuel mixture towards the ignition locations (i.e. spark-plugs) in the way of a uniformly distributed charge or by preserving stratification of the charge depending on operating mode of the engine

Experiments on melt dispersion with lateral failure in the bottom head of the pressure vessel

Energy Technology Data Exchange (ETDEWEB)

Meyer, L.; Gargallo, M. [Forschungszentrum Karlsruhe, Institut fur Kern-und Energietechnik, Karlsruhe (Germany)

2001-07-01

Melt dispersion experiments with lateral failure in the bottom head were carried out in a 1:18 scaled annular cavity design under low pressure conditions. Water and a bismuth alloy were used as melt simulant material and nitrogen as driving gas. With lateral breaches the liquid height in the lower head relative to the upper and lower edge of the breach is an additional parameter for the dispersion process. Shifting the break from the central position towards the side of the lower head leads to smaller melt dispersion, and a larger breach size does not necessarily lead to a larger dispersed melt fraction. (author)

Bottom nozzle for nuclear reactor fuel assembly having an adaptor plate and a coupled filtration plate

International Nuclear Information System (INIS)

Verdier, M.; Mortgat, R.

1992-01-01

The bottom nozzle includes an adaptor plate with openings to allow the passage of water and a filtration plate with small holes. The openings in the adaptor plate are symmetrical with regard to medians and diagonals. Within each zone, some of the openings are rectangular and some may be circular. The small holes in the filtration plate coincide with the rectangular openings in the adaptor plate

Real-time depth measurement for micro-holes drilled by lasers

Science.gov (United States)

Lin, Cheng-Hsiang; Powell, Rock A.; Jiang, Lan; Xiao, Hai; Chen, Shean-Jen; Tsai, Hai-Lung

2010-02-01

An optical system based on the confocal principle has been developed for real-time precision measurements of the depth of micro-holes during the laser drilling process. The capability of the measuring system is theoretically predicted by the Gaussian lens formula and experimentally validated to achieve a sensitivity of 0.5 µm. A nanosecond laser system was used to drill holes, and the hole depths were measured by the proposed measuring system and by the cut-and-polish method. The differences between these two measurements are found to be 5.0% for hole depths on the order of tens of microns and 11.2% for hundreds of microns. The discrepancies are caused mainly by the roughness of the bottom surface of the hole and by the existence of debris in the hole. This system can be easily implemented in a laser workstation for the fabrication of 3D microstructures.

Role of Effective Density in improving the accuracy of bottom pressure based sea level measurements - A case study from Gulf of Guinea

Digital Repository Service at National Institute of Oceanography (India)

Joseph, A.; Mehra, P.; Desai, R.G.P.; Dotse, J.; Odametey, J.T.; Nkebi, E.K.; Vijaykumar, K.; Prabhudesai, S.P.

of the sea water, as a result of turbulence induced by wind forcing and impact of rain drops, is suspected to be responsible for the observed effective reduction in the in situ density of this shallow water body The accuracy of bottom-pressure based sea level...

Bottom Pressure Tides Along a Line in the Southeast Atlantic Ocean and Comparisons with Satellite Altimetry

Science.gov (United States)

Ray, Richard D.; Byrne, Deidre A.

2010-01-01

Seafloor pressure records, collected at 11 stations aligned along a single ground track of the Topex/Poseidon and Jason satellites, are analyzed for their tidal content. With very low background noise levels and approximately 27 months of high-quality records, tidal constituents can be estimated with unusually high precision. This includes many high-frequency lines up through the seventh-diurnal band. The station deployment provides a unique opportunity to compare with tides estimated from satellite altimetry, point by point along the satellite track, in a region of moderately high mesoscale variability. That variability can significantly corrupt altimeter-based tide estimates, even with 17 years of data. A method to improve the along-track altimeter estimates by correcting the data for nontidal variability is found to yield much better agreement with the bottom-pressure data. The technique should prove useful in certain demanding applications, such as altimetric studies of internal tides.

Hole doping and pressure effects on the II-II-V-based diluted magnetic semiconductor (Ba1-xKx)(Zn1-yMny)2As2

International Nuclear Information System (INIS)

Sun, F.; Zhao, G. Q.; Escanhoela, C. A. Jr.

2017-01-01

We investigate doping- and pressure-induced changes in the electronic state of Mn 3d and As 4p orbitals in II-II-V based diluted magnetic semiconductor (Ba_1_-_x,K_x)(Zn_1_-_y,Mn_y)_2As_2 to shed light into the mechanism of indirect exchange interactions leading to high ferromagnetic ordering temperature (T_c = 230 K in optimally doped samples). A suite of x-ray spectroscopy experiments (emission, absorption and dichroism) show that the emergence, and further enhancement of ferromagnetic interactions with increased hole doping into the As 4p band is accompanied by a decrease in local 3d spin density at Mn sites. This is a result of increasing Mn 3d - As 4p hybridization with hole doping which enhances indirect exchange interactions between Mn dopants and gives rise to induced magnetic polarization in As 4p states. On the contrary, application of pressure suppresses exchange interactions. While Mn Kβ emission spectra show a weak response of 3d state to pressure, clear As 4p band broadening (hole delocalization) is observed under pressure ultimately leading to loss of ferromagnetism concomitant with a semiconductor to metal transition. The pressure response of As 4p and Mn 3d states is intimately connected with the evolution of the As-As interlayer distance and the geometry of the MnAs_4 tetrahedral units, which we probed with X-ray diffraction. Our results indicate that hole doping increases the degree of covalency between the anion (As) p states and cation (Mn) d states in the MnA_s_4 tetrahedron, a crucial ingredient to promote indirect exchange interactions between Mn dopants and high T_c ferromagnetism. As a result, the instability of ferromagnetism and semiconducting state against pressure is mainly dictated by delocalization of anion p states.

Study on the Gap Flow Simulation in EDM Small Hole Machining with Ti Alloy

Directory of Open Access Journals (Sweden)

Shengfang Zhang

2017-01-01

Full Text Available In electrical discharge machining (EDM process, the debris removed from electrode material strongly affects the machining efficiency and accuracy, especially for the deep small hole machining process. In case of Ti alloy, the debris movement and removal process in gap flow between electrodes for small hole EDM process is studied in this paper. Based on the solid-liquid two-phase flow equation, the mathematical model on the gap flow field with flushing and self-adaptive disturbation is developed. In our 3D simulation process, the count of debris increases with number of EDM discharge cycles, and the disturbation generated by the movement of self-adaptive tool in the gap flow is considered. The methods of smoothing and remeshing are also applied in the modeling process to enable a movable tool. Under different depth, flushing velocity, and tool diameter, the distribution of velocity field, pressure field of gap flow, and debris movement are analyzed. The statistical study of debris distribution under different machining conditions is also carried out. Finally, a series of experiments are conducted on a self-made machine to verify the 3D simulation model. The experiment results show the burn mark at hole bottom and the tapered wall, which corresponds well with the simulating conclusion.

Slim hole drilling and testing strategies

Science.gov (United States)

Nielson, Dennis L.; Garg, Sabodh K.; Goranson, Colin

2017-12-01

The financial and geologic advantages of drilling slim holes instead of large production wells in the early stages of geothermal reservoir assessment has been understood for many years. However, the practice has not been fully embraced by geothermal developers. We believe that the reason for this is that there is a poor understanding of testing and reservoir analysis that can be conducted in slim holes. In addition to reservoir engineering information, coring through the cap rock and into the reservoir provides important data for designing subsequent production well drilling and completion. Core drilling requires significantly less mud volume than conventional rotary drilling, and it is typically not necessary to cure lost circulation zones (LCZ). LCZs should be tested by either production or injection methods as they are encountered. The testing methodologies are similar to those conducted on large-diameter wells; although produced and/or injected fluid volumes are much less. Pressure, temperature and spinner (PTS) surveys in slim holes under static conditions can used to characterize temperature and pressure distribution in the geothermal reservoir. In many cases it is possible to discharge slim holes and obtain fluid samples to delineate the geochemical properties of the reservoir fluid. Also in the latter case, drawdown and buildup data obtained using a downhole pressure tool can be employed to determine formation transmissivity and well properties. Even if it proves difficult to discharge a slim hole, an injection test can be performed to obtain formation transmissivity. Given the discharge (or injection) data from a slimhole, discharge properties of a large-diameter well can be inferred using wellbore modeling. Finally, slim hole data (pressure, temperature, transmissivity, fluid properties) together with reservoir simulation can help predict the ability of the geothermal reservoir to sustain power production.

Production Optimization for Two-Phase Flow in an Oil Reservoir

DEFF Research Database (Denmark)

Völcker, Carsten; Jørgensen, John Bagterp; Thomsen, Per Grove

2012-01-01

framework to increase the production and economic value of an oil reservoir. Wether the objective is to maximize recovery or some financial measure like Net Present Value, the increased production is achieved by manipulation of the well rates and bottom-hole pressures of the injection and production wells....... The optimal water injection rates and production well bottom-hole pressures are computed by solution of a large-scale constrained optimal control problem. The objective is to maximize production by manipulating the well rates and bottom hole pressures of injection and production wells. Optimal control...... settings of injection and production wells are computed by solution of a large scale constrained optimal control problem. We describe a gradient based method to compute the optimal control strategy of the water flooding process. An explicit singly diagonally implicit Runge-Kutta (ESDIRK) method...

Oil Well Bottom Hole Locations, This GIS data set was produced as a general reference for the Department of Natural Resources, the oil and gas industry, environmental and regulatory agencies, landowners, and the public., Published in 2007, 1:24000 (1in=2000ft) scale, Louisiana State University (LSU).

Data.gov (United States)

NSGIC Education | GIS Inventory — Oil Well Bottom Hole Locations dataset current as of 2007. This GIS data set was produced as a general reference for the Department of Natural Resources, the oil and...

Scour protection for wind turbine foundations on highly erodible sea bottom

Energy Technology Data Exchange (ETDEWEB)

Ottesen Hansen, N.E.

2002-12-01

Scour around offshore structures is well known. It is caused by the strong eddy formation at the base of the structures protruding from the sea bottom. The strong vortices result in an amplified effective shear stress working on the sea bottom surface adjacent to the structure. When the surrounding sea bottom is lowered the scour protection will end up being a cap on a small hill and when the slopes are getting too steep the scour protection will roll or slide down the sides. It will loose its cohesion and therefore its integrity. This will take place irrespective of the type of scour protection material and the type of scour protection. This report describes scour protections, which can deal with this particular problem. Such a scour protection must be able to sustain the following loads: Be able to follow the lowering of the seabed on its way down; Be resistant to edge scour (scour around the perimeter of the scour protection). The installation of scour protection is not straightforward because the developed scour hole may be very uneven. It will be highly impractical to survey the hole although it can be done. There will be power cables etc. obstructing for ROV's or instrumented backhoe arms. Therefore the recommended method is to assume that the scour hole is developed and to place the scour protection material evenly around the foundation. In practice this is done by fall pipes positioned from a barge or by an instrumented backhoe. The procedure will be as follows: The outline of the scour hole is surveyed by a ROV (eye ball) and the status of the power cables are investigated; If the tie-in of the power cables are hanging as free spans, material shall be dumped on these spans in order to cover them. This material shall have a size, which will not be harmful to the cable during a dumping; Alternatively the tie-in takes place through an armoured flex-pipe that can sustain the impact from the stone dumping. Hence, in this case the stone dumping can commence

Method for Cleaning Laser-Drilled Holes on Printed Wiring Boards by Plasma Treatment

Science.gov (United States)

Hirogaki, Toshiki; Aoyama, Eiichi; Minagi, Ryu; Ogawa, Keiji; Katayama, Tsutao; Matsuoka, Takashi; Inoue, Hisahiro

We propose a new method for cleaning blind via holes after laser drilling of PWBs using oxygen plasma treatment. This report dealt with three kinds of PWB materials: epoxy resin and two kinds of aramid fiber reinforced plastics (AFRP: Technora or Kevlar fiber reinforcement). We observed the drilled holes after plasma treatment using both an optical and a scanning electric microscope (SEM). It was confirmed that adequate etching took place in the drilled holes by plasma treatment. We also compared the hole wall and hole bottom after plasma treatment with ones after chemical etching. It was clear that there was no damage to the aramid fiber tip on the hole wall, and that a smooth roughness of the hole wall was obtained by means of plasma treatment. As a result, we demonstrated that the plasma treatment is effective in cleaning the laser drilled holes of PWBs.

A gas production system from methane hydrate layers by hot water injection and BHP control with radial horizontal wells

Energy Technology Data Exchange (ETDEWEB)

Yamakawa, T.; Ono, S.; Iwamoto, A.; Sugai, Y.; Sasaki, K. [Kyushu Univ., Fukuoka, Fukuoka (Japan)

2010-07-01

Reservoir characterization of methane hydrate (MH) bearing turbidite channel in the eastern Nankai Trough, in Japan has been performed to develop a gas production strategy. This paper proposed a gas production system from methane hydrate (MH) sediment layers by combining the hot water injection method and bottom hole pressure control at the production well using radial horizontal wells. Numerical simulations of the cylindrical homogeneous MH layer model were performed in order to evaluate gas production characteristics by the depressurization method with bottom hole pressure control. In addition, the effects of numerical block modeling and averaging physical properties of MH layers were presented. According to numerical simulations, combining the existing production system with hot water injection and bottom hole pressure control results in an outward expansion of the hot water chamber from the center of the MH layer with continuous gas production. 10 refs., 15 figs.

Method of hydrospalling

International Nuclear Information System (INIS)

Oudenhoven, M.S.

1983-01-01

A method is disclosed of breaking rock from a free surface which uses hydrofracturing to induce rock failure. Initially, a hole is cut in the rock face to a depth suitable for spalling by a high pressure water jet drill. Next, at the bottom of this hole a thin circular slot is hydraulically cut into the rock. The slot's circular axis is cut parallel to the transverse axis of the hole and the slot is made larger than the hole diameter. Following this step, a high pressure packer, with a high pressure tube passing through its center, is inserted into the drill hole. This packer is placed near the bottom of the hole above the slot and inflated. A fluid, like water, under high pressure is pumped down the hole past the packer into the slotted area. This high pressure fluid initiates a tensile fracture in the rock at the circular periphery of the slot. Tension is induced in the rock at this peripheral location due to the small radius of curvature existing there. This circular tensile fracture propagates outward away from the drill hole and upward to the free rock surface. After the rock fragment is broken free, pressure is released from the packer and it is withdrawn from the hole letting the fragment drop. To advance through the rock, the process is continuously repeated with the high pressure fluid being applied to the slotted area over a very short time period

Using GIS to appraise structural control of the river bottom morphology near hydrotechnical objects on Alluvial rivers

Science.gov (United States)

Habel, Michal; Babinski, Zygmunt; Szatten, Dawid

2017-11-01

The paper presents the results of analyses of structural changes of the Vistula River bottom, in a section of direct influence of the bridge in Torun (Northern Poland) fitted with one pier in the form of a central island. The pier limits a free water flow by reducing the active width of the riverbed by 12%. In 2011, data on the bottom morphology was collected, i.e. before commencing bridge construction works, throughout the whole building period - 38 measurements. Specific river depth measurements are carried out with SBES and then bathymetric maps are drawn up every two months. The tests cover the active Vistula river channel of 390 - 420 metres in width, from 730+40 to 732+30 river kilometre. The paper includes the results of morphometric analyses of vertical and horizontal changes of the river bottom surrounded by the bridge piers. The seasonality of scour holes and inclination of accumulative forms (sand bars) in the relevant river reach was analysed. Morphometric analyses were performed on raster bases with GIS tools, including the Map Algebra algorithm. The obtained results shown that scour holes/pools of up to 10 metres in depth and exceeding 1200 metres in length are formed in the tested river segment. Scour holes within the pier appeared in specific periods. Constant scour holes were found at the riverbank, and the rate of their movement down the river was 0.6 to 1.3 m per day. The tests are conducted as part of a project ordered by the City of Torun titled `Monitoring Hydrotechniczny Inwestycji Mostowej 2011 - 2014' (Hydrotechnical Monitoring of the Bridge Investment, period 2011 - 2014).

Direct calibration framework of triple-hole pressure probes for incompressible flow

International Nuclear Information System (INIS)

Díaz, K M Argüelles; Oro, J M Fernández; Marigorta, E Blanco

2008-01-01

This paper carries out a mathematical analysis of the limits and data reduction techniques of three-hole pressure (THP) probes operating in a 'non-nulling' mode for incompressible flow. As a result of this analysis, a direct procedure is advanced, based on the distinction of several zones within the angular range, where different relations can be applied to obtain the flow variables. This proposal provides a considerable increment of the operative angular range of THP probes: about ±70° instead of the typical ±35° for a cylindrical probe. This may extend the application of these probes in highly unsteady flows, or reduce the acquisition and data reduction effort minimizing the necessity of probe reorientation. The influence of the data reduction technique on the uncertainty transmission is also presented in the paper. From detailed considerations, it is demonstrated that the results uncertainty depends on the specific probe, but it is unaffected by the mathematical procedure employed to calculate the flow variables. Validation measurements with pneumatic probes have been made for Reynolds numbers from 4 × 10 3 to 3.5 × 10 4 . In addition, a highly unsteady measurement in a low-speed axial flow fan is succinctly analysed. Taking into account both attainable angular range and uncertainty, it is determined that the optimal construction angle for the holes of a low frequency response THP probe lies between 30° and 60°, while for fast response probes, in order to avoid the separated flow region, the optimal construction angle is around 30°

High pressure injection of dimethyl ether

Energy Technology Data Exchange (ETDEWEB)

Glensvig, M.; Sorenson, S.C.; Abata, D.L.

1997-08-01

The purpose of this investigation was to achieve a better understanding of the fundamental spray behavior of DME (Dimenthyl Ether) using a standard diesel pump with pintle and hole nozzles. Fundamental spray behavior was characterized by determining fuel spray penetration and angle, atomization and evaporation. The influences of opening pressure, nozzle geometry and ambient pressure above and below the critical pressure of the fuel on the spray behavior were investigated. The influence of opening pressures on the spray characteristics for the hole nozzle was investigated. The results showed that for opening pressures of 120 bar and 180 bar the spray has a similar appearance. For the higher opening pressure (200 bar and 240 bar), the initial spray breaks up very rapidly giving a high initial spray angle. The opening pressure had little influence on spray penetration. The spray angle later in the injection increased as the opening pressure was decreased. Above the critical pressure, the spray from the hole nozzle had a more irregular shape. Penetration decreased and the spray angle increased above the critical pressure. Three pintle nozzles with different geometries and opening pressures were tested. The appearance of the three sprays were very similar. The sprays seemed to be more sharply pointed as the nozzle hole angle decreased. The nozzle with the 4 deg. hole nozzle angle and an opening pressure of 280 bar had the highest penetration and highest initial spray angle. The pintle nozzle with the 12 deg. hole nozzle angle and opening pressure of approx. 450 bar was tested above the critical ambient pressure. Penetration was very similar for injection above and below the critical ambient pressure, while the spray angle decreased for the spray above the critical ambient pressure. (au)

Microscopic origin of black hole reentrant phase transitions

Science.gov (United States)

Zangeneh, M. Kord; Dehyadegari, A.; Sheykhi, A.; Mann, R. B.

2018-04-01

Understanding the microscopic behavior of the black hole ingredients has been one of the important challenges in black hole physics during the past decades. In order to shed some light on the microscopic structure of black holes, in this paper, we explore a recently observed phenomenon for black holes namely reentrant phase transition, by employing the Ruppeiner geometry. Interestingly enough, we observe two properties for the phase behavior of small black holes that leads to reentrant phase transition. They are correlated and they are of the interaction type. For the range of pressure in which the system underlies reentrant phase transition, it transits from the large black holes phase to the small one which possesses higher correlation than the other ranges of pressures. On the other hand, the type of interaction between small black holes near the large/small transition line differs for usual and reentrant phase transitions. Indeed, for the usual case, the dominant interaction is repulsive whereas for the reentrant case we encounter an attractive interaction. We show that in the reentrant phase transition case, the small black holes behave like a bosonic gas whereas in the usual phase transition case, they behave like a quantum anyon gas.

Revisiting the round bottom flask rainbow experiment

Science.gov (United States)

Selmke, Markus; Selmke, Sarah

2018-01-01

A popular demonstration experiment in optics uses a round-bottom flask filled with water to project a circular rainbow on a screen with a hole through which the flask is illuminated. We show how the vessel's wall shifts the first- and second-order bows towards each other and consequently reduces the width of Alexander's dark band. We address the challenge this introduces in observing Alexander's dark band, and explain the importance of a sufficient distance between the flask and the screen. The wall-effect also introduces a splitting of the bows that can easily be misinterpreted.

Compressibility of rotating black holes

International Nuclear Information System (INIS)

Dolan, Brian P.

2011-01-01

Interpreting the cosmological constant as a pressure, whose thermodynamically conjugate variable is a volume, modifies the first law of black hole thermodynamics. Properties of the resulting thermodynamic volume are investigated: the compressibility and the speed of sound of the black hole are derived in the case of nonpositive cosmological constant. The adiabatic compressibility vanishes for a nonrotating black hole and is maximal in the extremal case--comparable with, but still less than, that of a cold neutron star. A speed of sound v s is associated with the adiabatic compressibility, which is equal to c for a nonrotating black hole and decreases as the angular momentum is increased. An extremal black hole has v s 2 =0.9 c 2 when the cosmological constant vanishes, and more generally v s is bounded below by c/√(2).

Underground processing method for radiation-contaminated material and transferring method for buffer molding material

International Nuclear Information System (INIS)

Akasaka, Hidenari; Shimura, Satoshi; Asano, Eiichi; Yamagata, Junji; Ninomiya, Nobuo; Kawakami, Susumu.

1995-01-01

A bottomed molding material (buffer molding material) is formed into a bottomed cylindrical shape by solidifying, under pressure, powders such as of bentonite into a highly dense state by a cold isotropic pressing or the like, having a hole for accepting and containing a vessel for radiation-contaminated materials. The bottomed cylindrical molding material is loaded on a transferring vessel, and transferred to a position near the site for underground disposal. The bottomed cylindrical molding material having a upwarded containing hole is buried in the cave for disposal. The container for radiation-contaminated material is loaded and contained in the containing hole of the bottomed cylindrical molding material. A next container for radiation-contaminated materials is juxtaposed thereover. Then, a bottomed cylindrical molding material having a downwarded containing hole is covered to the container for the radiation-contaminated material in a state being protruded upwardly. The radiation-contaminated material is thus closed by a buffer material of the same material at the circumference thereof. (I.N.)

Selection of peripheral intravenous catheters with 24-gauge side-holes versus those with 22-gauge end-hole for MDCT: A prospective randomized study

Energy Technology Data Exchange (ETDEWEB)

Tamura, Akio, E-mail: a.akahane@gmail.com [Department of Radiology, Iwate Medical University School of Medicine, 19-1 Uchimaru, Morioka 020-8505 (Japan); Kato, Kenichi, E-mail: kkato@iwate-med.ac.jp [Department of Radiology, Iwate Medical University School of Medicine, 19-1 Uchimaru, Morioka 020-8505 (Japan); Kamata, Masayoshi, E-mail: kamataaoi@yahoo.co.jp [Iwate Medical University Hospital, 19-1 Uchimaru, Morioka 020-8505 (Japan); Suzuki, Tomohiro, E-mail: suzukitomohiro123@gmail.com [Department of Radiology, Iwate Medical University School of Medicine, 19-1 Uchimaru, Morioka 020-8505 (Japan); Suzuki, Michiko, E-mail: mamimichiko@me.com [Department of Radiology, Iwate Medical University School of Medicine, 19-1 Uchimaru, Morioka 020-8505 (Japan); Nakayama, Manabu, E-mail: gakuymgt@yahoo.co.jp [Department of Radiology, Iwate Medical University School of Medicine, 19-1 Uchimaru, Morioka 020-8505 (Japan); Tomabechi, Makiko, E-mail: mtomabechi@mac.com [Department of Radiology, Iwate Medical University School of Medicine, 19-1 Uchimaru, Morioka 020-8505 (Japan); Nakasato, Tatsuhiko, E-mail: nakasato77@gmail.com [Department of Radiology, Southern Tohoku Research Institute for Neuroscience, 7-115 Yatsuyamada, Koriyama 963-8563 (Japan); Ehara, Shigeru, E-mail: ehara@iwate-med.ac.jp [Department of Radiology, Iwate Medical University School of Medicine, 19-1 Uchimaru, Morioka 020-8505 (Japan)

2017-02-15

Highlights: • We compared 24-gauge side-hole and conventional 22-gauge end-hole catheters in MDCT. • The 24-gauge side-hole catheter is noninferior to the 22-gauge end-hole catheter. • The 24-gauge side-hole catheter is safe and facilitates optimal enhancement quality. • The 24-gauge side-hole catheter is suitable for patients with narrow or fragile veins. - Abstract: Purpose: To compare the 24-gauge side-holes catheter and conventional 22-gauge end-hole catheter in terms of safety, injection pressure, and contrast enhancement on multi-detector computed tomography (MDCT). Materials & methods: In a randomized single-center study, 180 patients were randomized to either the 24-gauge side-holes catheter or the 22-gauge end-hole catheter groups. The primary endpoint was safety during intravenous administration of contrast material for MDCT, using a non-inferiority analysis (lower limit 95% CI greater than −10% non-inferiority margin for the group difference). The secondary endpoints were injection pressure and contrast enhancement. Results: A total of 174 patients were analyzed for safety during intravenous contrast material administration for MDCT. The overall extravasation rate was 1.1% (2/174 patients); 1 (1.2%) minor episode occurred in the 24-gauge side-holes catheter group and 1 (1.1%) in the 22-gauge end-hole catheter group (difference: 0.1%, 95% CI: −3.17% to 3.28%, non-inferiority P = 1). The mean maximum pressure was higher with the 24-gauge side-holes catheter than with the 22-gauge end-hole catheter (8.16 ± 0.95 kg/cm{sup 2} vs. 4.79 ± 0.63 kg/cm{sup 2}, P < 0.001). The mean contrast enhancement of the abdominal aorta, celiac artery, superior mesenteric artery, and pancreatic parenchyma in the two groups were not significantly different. Conclusion: In conclusion, our study showed that the 24-gauge side-holes catheter is safe and suitable for delivering iodine with a concentration of 300 mg/mL at a flow-rate of 3 mL/s, and it may contribute to

Overview of Hole GT2A: Drilling middle gabbro in Wadi Tayin massif, Oman ophiolite

Science.gov (United States)

Takazawa, E.; Kelemen, P. B.; Teagle, D. A. H.; Coggon, J. A.; Harris, M.; Matter, J. M.; Michibayashi, K.

2017-12-01

Hole GT2A (UTM: 40Q 655960.7E / 2529193.5N) was drilled by the Oman Drilling Project (OmDP) into Wadi Gideah of Wadi Tayin massif in the Samail ophiolite, Oman. OmDP is an international collaboration supported by the International Continental Scientific Drilling Program, the Deep Carbon Observatory, NSF, IODP, JAMSTEC, and the European, Japanese, German and Swiss Science Foundations, with in-kind support in Oman from the Ministry of Regional Municipalities and Water Resources, Public Authority of Mining, Sultan Qaboos University, and the German University of Technology. Hole GT2A was diamond cored in 25 Dec 2016 to 18 Jan 2017 to a total depth of 406.77 m. The outer surfaces of the cores were imaged and described on site before being curated, boxed and shipped to the IODP drill ship Chikyu, where they underwent comprehensive visual and instrumental analysis. 33 shipboard scientists were divided into six teams (Igneous, Alteration, Structural, Geochem, Physical Properties, Paleomag) to describe and analyze the cores. Hole GT2A drilled through the transition between foliated and layered gabbro. The transition zone occurs between 50 and 150 m curation corrected depth (CCD). The top 50 m of Hole GT2A is foliated gabbro whereas the bottom 250 m consists of layered gabbro. Brittle fracture is observed throughout the core. Intensity of alteration vein decreases from the top to the bottom of the hole. On the basis of changes in grain size and/or modal abundance and/or appearance/disappearance of igneous primary mineral(s) five lithological units are defined in Hole GT2A (Unit I to V). The uppermost part of Hole GT2A (Unit I) is dominated by fine-grained granular olivine gabbro intercalated with less dominant medium-grained granular olivine gabbro and rare coarse-grained varitextured gabbro. The lower part of the Hole (Units II, III and V) is dominated by medium-grained olivine gabbro, olivine melagabbro and olivine-bearing gabbro. Modally-graded rhythmic layering with

Eliminating dependence of hole depth on aspect ratio by forming ammonium bromide during plasma etching of deep holes in silicon nitride and silicon dioxide

Science.gov (United States)

Iwase, Taku; Yokogawa, Kenetsu; Mori, Masahito

2018-06-01

The reaction mechanism during etching to fabricate deep holes in SiN/SiO2 stacks by using a HBr/N2/fluorocarbon-based gas plasma was investigated. To etch SiN and SiO2 films simultaneously, HBr/fluorocarbon gas mixture ratio was controlled to achieve etching selectivity closest to one. Deep holes were formed in the SiN/SiO2 stacks by one-step etching at several temperatures. The surface composition of the cross section of the holes was analyzed by time-of-flight secondary-ion mass spectrometry. It was found that bromine ions (considered to be derived from NH4Br) were detected throughout the holes in the case of low-temperature etching. It was also found that the dependence of hole depth on aspect ratio decreases as temperature decreases, and it becomes significantly weaker at a substrate temperature of 20 °C. It is therefore concluded that the formation of NH4Br supplies the SiN/SiO2 etchant to the bottom of the holes. Such a finding will make it possible to alleviate the decrease in etching rate due to a high aspect ratio.

Permeability of granular beds emplaced in vertical drill holes

International Nuclear Information System (INIS)

Griffiths, S.K.; Morrison, F.A. Jr.

1979-01-01

To determine the permeabilities of granular materials emplaced in vertical drill holes used for underground nuclear tests, an experiment at the USDOE Nevada Test Site (NTS) was conducted. As the hole is being filled, falling material increases pressure above and within the granular beds beneath. When the filling operation starts or stops, a transient pressure response occurs within the beds; measurements of this response in beds of various compositions were made. The permeabilities after emplacement were found by matching analytical predictions of the response to these data. This information is useful in assuring the containment of nuclear tests conducted in such drill holes

Apparatus for atmospheric pressure pin-to-hole spark discharge and uses thereof

Science.gov (United States)

Dobrynin, Danil V.; Fridman, Alexander; Cho, Young I.; Fridman, Gregory; Friedman, Gennady

2016-12-06

Disclosed herein are atmospheric pressure pin-to-hole pulsed spark discharge devices and methods for creating plasma. The devices include a conduit for fluidically communicating a gas, a plasma, or both, therethrough, portion of the conduit capable of being connected to a gas supply, and a second portion of the conduit capable of emitting a plasma; a positive electrode comprising a sharp tip; and a ground plate electrode. Disclosed are methods for treating a skin ulcer using non-thermal plasma include flowing a gas through a cold spark discharge zone simultaneously with the creation of a pulsed spark discharge to give rise to a non-thermal plasma emitted from a conduit, the non-thermal plasma comprising NO; and contacting a skin ulcer with said non-thermal plasma for sufficient time and intensity to give rise to treatment of the skin ulcer.

Coherent electron - hole state and femtosecond cooperative emission in bulk GaAs

International Nuclear Information System (INIS)

Vasil'ev, Petr P; Kan, H; Ohta, H; Hiruma, T

2002-01-01

The conditions for obtaining a collective coherent electron - hole state in semiconductors are discussed. The results of the experimental study of the regime of cooperative recombination of high-density electrons and holes (more than 3 x 10 18 cm -3 ) in bulk GaAs at room temperature are presented. It is shown that the collective pairing of electrons and holes and their condensation cause the formation of a short-living coherent electron - hole BCS-like state, which exhibits radiative recombination in the form of high-power femtosecond optical pulses. It is experimentally demonstrated that almost all of the electrons and holes available are condensed at the very bottoms of the bands and are at the cooperative state. The average lifetime of this state is measured to be of about 300 fs. The dependences of the order parameter (the energy gap of the spectrum of electrons and holes) and the Fermi energy of the coherent BCS state on the electron - hole concentration are obtained. (special issue devoted to the 80th anniversary of academician n g basov's birth)

Assessment of pseudo-bilayer structures in the heterogate germanium electron-hole bilayer tunnel field-effect transistor

International Nuclear Information System (INIS)

Padilla, J. L.; Alper, C.; Ionescu, A. M.; Medina-Bailón, C.; Gámiz, F.

2015-01-01

We investigate the effect of pseudo-bilayer configurations at low operating voltages (≤0.5 V) in the heterogate germanium electron-hole bilayer tunnel field-effect transistor (HG-EHBTFET) compared to the traditional bilayer structures of EHBTFETs arising from semiclassical simulations where the inversion layers for electrons and holes featured very symmetric profiles with similar concentration levels at the ON-state. Pseudo-bilayer layouts are attained by inducing a certain asymmetry between the top and the bottom gates so that even though the hole inversion layer is formed at the bottom of the channel, the top gate voltage remains below the required value to trigger the formation of the inversion layer for electrons. Resulting benefits from this setup are improved electrostatic control on the channel, enhanced gate-to-gate efficiency, and higher I ON levels. Furthermore, pseudo-bilayer configurations alleviate the difficulties derived from confining very high opposite carrier concentrations in very thin structures

Assessment of pseudo-bilayer structures in the heterogate germanium electron-hole bilayer tunnel field-effect transistor

Energy Technology Data Exchange (ETDEWEB)

Padilla, J. L., E-mail: jose.padilladelatorre@epfl.ch; Alper, C.; Ionescu, A. M. [Nanoelectronic Devices Laboratory, École Polytechnique Fédérale de Lausanne, Lausanne CH-1015 (Switzerland); Medina-Bailón, C.; Gámiz, F. [Departamento de Electrónica y Tecnología de los Computadores, Universidad de Granada, Avda. Fuentenueva s/n, 18071 Granada (Spain)

2015-06-29

We investigate the effect of pseudo-bilayer configurations at low operating voltages (≤0.5 V) in the heterogate germanium electron-hole bilayer tunnel field-effect transistor (HG-EHBTFET) compared to the traditional bilayer structures of EHBTFETs arising from semiclassical simulations where the inversion layers for electrons and holes featured very symmetric profiles with similar concentration levels at the ON-state. Pseudo-bilayer layouts are attained by inducing a certain asymmetry between the top and the bottom gates so that even though the hole inversion layer is formed at the bottom of the channel, the top gate voltage remains below the required value to trigger the formation of the inversion layer for electrons. Resulting benefits from this setup are improved electrostatic control on the channel, enhanced gate-to-gate efficiency, and higher I{sub ON} levels. Furthermore, pseudo-bilayer configurations alleviate the difficulties derived from confining very high opposite carrier concentrations in very thin structures.

How many holes is too many? A prototype tool for estimating mosquito entry risk into damaged bed nets.

Science.gov (United States)

Sutcliffe, James; Ji, Xin; Yin, Shaoman

2017-08-01

Insecticide-treated bed nets (ITNs) have played an integral role in malaria reduction but how insecticide depletion and accumulating physical damage affect ITN performance is poorly understood. More accurate methods are needed to assess damage to bed nets so that they can be designed, deployed and replaced optimally. Video recordings of female Anopheles gambiae in near approach (1-½ cm) to occupied untreated rectangular bed nets in a laboratory study were used to quantify the amount of mosquito activity (appearances over time) around different parts of the net, the per-appearance probability of a mosquito coming close to holes of different sizes (hole encounter) and the per-encounter probability of mosquitoes passing through holes of different sizes (hole passage). Appearance frequency on different parts of the net reflected previously reported patterns: the area of the net under greatest mosquito pressure was the roof, followed by the bottom 30 cm of the sides, followed by the 30 cm area immediately above this, followed by the upper two-thirds of the sides. The ratio of activity in these areas was (respectively) 250:33:5:1. Per-appearance probability of hole encounter on all parts of the net was strongly predicted by a factor combining hole perimeter and area. Per-encounter probability of hole passage, in turn, was strongly predicted by hole width. For a given width, there was a 20% greater risk of passage through holes on the roof than holes on the sides. Appearance, encounter and passage predictors correspond to various mosquito behaviours that have previously been described and are combined into a prototype mosquito entry risk tool that predicts mosquito entry rates for nets with various amounts of damage. Scenarios that use the entry risk tool to test the recommendations of the WHOPES proportionate hole index (pHI) suggest that the pHI hole size categories and failure to account for hole location likely sometimes lead to incorrect conclusions about net

Hole doping by pressure on the 1111 pnictides CaFeAsF and SrFeAsF

International Nuclear Information System (INIS)

Freitas, Daniele C; Sow, Amadou; Núñez-Regueiro, Manuel; Garbarino, Gastón; Weht, Ruben; Zhu, Xiyu; Han, Fei; Cheng, Peng; Ju, Jing; Hu Wen, Hai

2014-01-01

We determine the pressure phase diagram of the 1111 compounds CaFeAsF and SrFeAsF, up to 20 GPa and down to 4 K by electrical resistivity measurements and the change of structure up to 40 GPa at room temperature. The antiferromagnetic transition temperature, as determined by the derivative peak, shows a minimum at ∼5 GPa (10 GPa) for the Ca (Sr) compound. For CaFeAsF, superconductivity appears at this minimum, coincident with the development of a previously reported monoclinic phase. For SrFeAsF, where the orthorhombic and the monoclinic phase were reported to coexist, superconductivity exists above P≥1 GPa. Both phase diagrams can be scaled by a shift of ∼10 GPa pressure at which the volume of SrFeAsF and that of CaFeAsF at ambient pressure coincide. The difference of our phase diagram with that of electron-doped 1111 samples is accounted for by hole doping under pressure, which we verified through electron band structure calculations. (papers)

Refinement of the bottom boundary of the INES scale

International Nuclear Information System (INIS)

Ferjencik, Milos

2010-01-01

No existing edition of the International Nuclear Events Scale (INES) Manual addresses in depth the determination of the bottom boundary of the Scale, although a need for a definition is felt. The article introduces a method for determining the INES bottom boundary applicable to pressurized water reactors. This bottom boundary is put identical with the threshold of degradation of the installation's nuclear safety assurance. A comprehensive flowchart has been developed as the main outcome of the analysis of the nuclear safety assurance violation issue. The use of this flowchart in INES classification to replace the introductory question in the General INES Rating Procedure in the INES Manual is recommended. (orig.)

Combining Top-down and Bottom-up Accountability: Evidence from a Bribery Experiment.

OpenAIRE

Danila Serra

2008-01-01

Monitoring corruption typically relies on top-down interventions aimed at increasing the probability of external controls and the severity of punishment. An alternative approach to fighting corruption is to induce bottom-up pressure for reform. Recent studies have shown that both top-down and bottom-up mechanisms are rarely able to keep service providers accountable. This paper investigates the effectiveness of an accountability system that combines bottom-up monitoring and top-down auditing ...

Drilling history core hole DC-8

International Nuclear Information System (INIS)

1978-10-01

Core hole DC-8 was completed in August, 1978 by Boyles Brothers Drilling Company, Spokane, Washington, under subcontract to Fenix and Scission, Inc. The hole was cored for the US Department of Energy and the Rockwell Hanford Operations' Basalt Waste Isolation Program. Fenix and Scisson, Inc. furnished the engineering, daily supervision of the core drilling activities, and geologic core logging for hole DC-8. Core hole DC-8 is located on the Hanford Site near the Wye Barricade and 50 feet northwest of rotary hole DC-7. The Hanford Site vation coordinates for DC-8 are North 14,955.94 feet and West 14,861.92 coordinates for DC-8 are North 14,955.94 feet and West 14,861.92 mean sea level. The purpose of core hole DC-8 was to core drill vertically through the basalt and interbed units for stratigraphic depth determination and core collection, and to provide a borehole for hydrologic testing and cross-hole seismic shear and pressure wave velocity studies with rotary hole DC-7. The total depth of core hole DC-8 was 4100.5 feet. Core recovery exceeded 97 percent of the total footage cored

Drilling history core hole DC-8

Energy Technology Data Exchange (ETDEWEB)

1978-10-01

Core hole DC-8 was completed in August, 1978 by Boyles Brothers Drilling Company, Spokane, Washington, under subcontract to Fenix and Scission, Inc. The hole was cored for the US Department of Energy and the Rockwell Hanford Operations' Basalt Waste Isolation Program. Fenix and Scisson, Inc. furnished the engineering, daily supervision of the core drilling activities, and geologic core logging for hole DC-8. Core hole DC-8 is located on the Hanford Site near the Wye Barricade and 50 feet northwest of rotary hole DC-7. The Hanford Site vation coordinates for DC-8 are North 14,955.94 feet and West 14,861.92 coordinates for DC-8 are North 14,955.94 feet and West 14,861.92 mean sea level. The purpose of core hole DC-8 was to core drill vertically through the basalt and interbed units for stratigraphic depth determination and core collection, and to provide a borehole for hydrologic testing and cross-hole seismic shear and pressure wave velocity studies with rotary hole DC-7. The total depth of core hole DC-8 was 4100.5 feet. Core recovery exceeded 97 percent of the total footage cored.

Featured Image: Making a Rapidly Rotating Black Hole

Science.gov (United States)

Kohler, Susanna

2017-10-01

These stills from a simulation show the evolution (from left to right and top to bottom) of a high-mass X-ray binary over 1.1 days, starting after the star on the right fails to explode as a supernova and then collapses into a black hole. Many high-mass X-ray binaries like the well-known Cygnus X-1, the first source widely accepted to be a black hole host rapidly spinning black holes. Despite our observations of these systems, however, were still not sure how these objects end up with such high rotation speeds. Using simulations like that shown above, a team of scientists led by Aldo Batta (UC Santa Cruz) has demonstrated how a failed supernova explosion can result in such a rapidly spinning black hole. The authors work shows that in a binary where one star attempts to explode as a supernova and fails it doesnt succeed in unbinding the star the large amount of fallback material can interact with the companion star and then accrete onto the black hole, spinning it up in the process. You can read more about the authors simulations and conclusions in the paper below.CitationAldo Batta et al 2017 ApJL 846 L15. doi:10.3847/2041-8213/aa8506

Methods to ensure optimal off-bottom and drill bit distance under pellet impact drilling

Science.gov (United States)

Kovalyov, A. V.; Isaev, Ye D.; Vagapov, A. R.; Urnish, V. V.; Ulyanova, O. S.

2016-09-01

The paper describes pellet impact drilling which could be used to increase the drilling speed and the rate of penetration when drilling hard rock for various purposes. Pellet impact drilling implies rock destruction by metal pellets with high kinetic energy in the immediate vicinity of the earth formation encountered. The pellets are circulated in the bottom hole by a high velocity fluid jet, which is the principle component of the ejector pellet impact drill bit. The paper presents the survey of methods ensuring an optimal off-bottom and a drill bit distance. The analysis of methods shows that the issue is topical and requires further research.

Dynamic hole closure behind a deep ocean sediment penetrator

International Nuclear Information System (INIS)

Dzwilewski, P.T.; Karnes, C.H.

1982-01-01

A freefall or boosted penetrator is one concept being considered to dispose of nuclear waste in the deep ocean seabed. For this technique to be acceptable, the sediment must be an effective barrier to the migration of radioactive nuclides, which means that the hole behind the advancing penetrator must close. One mechanism which can cause the hole to close immediately behind the penetrator is the reduction in water pressure in the wake as water tries to follow the penetrator into the sediment. An approximate solution to this complex problem is presented which analyzes the deformation of the sediment with a nonlinear, large displacement and strain, Lagrangian finite-difference computer code (STEALTH). The water was treated by Bernoulli's Principle for flow in a pipe resulting in a pressure boundary condition applied to the sediment surface along the path after passage of the penetrator. Two one-dimensional and eight two-dimensional calculations were performed with various penetrator velocities (15, 30, and 60 m/s) and sediment shear strengths. In two of the calculations, the dynamic pressure reduction was neglected to see if geostatic stresses alone would close the hole. The results of this study showed that geostatic stresses alone would not close the hole but the dynamic pressure reduction would. The largest uncertainty in the analysis was the pressure conditions in the water behind the penetrator in which frictionless, steady-state flow, in a uniform diameter pipe was assumed. A more sophisticated and realistic pressure condition has been formulated and will be implemented in the computer code in the near future

Magnetic holes in the dipolarized magnetotail: ion and electron anisotropies

Science.gov (United States)

Shustov, P.; Artemyev, A.; Zhang, X. J.; Yushkov, E.; Petrukovich, A. A.

2017-12-01

We conduct statistics on magnetic holes observed by THEMIS spacecraft in the near-Earth magnetotail. Groups of holes are detected after dipolarizations in the quiet, equatorial plasma sheet. Magnetic holes are characterized by significant magnetic field depressions (up to 50%) and strong electron currents ( 10-50 nA/m2), with spatial scales much smaller than the ion gyroradius. These magnetic holes are populated by hot (>10 keV), transversely anisotropic electrons supporting the pressure balance. We present statistical properties of these sub-ion scale magnetic holes and discuss possible mechanisms on the hole formation.

Peach Bottom transient analysis with BWR TRACB02

International Nuclear Information System (INIS)

Alamgir, M.; Sutherland, W.A.

1984-01-01

TRAC calculations have been performed for a Turbine Trip transient (TT1) in the Peach Bottom BWR power plant. This study is a part of the qualification of the BWR-TRAC code. The simulation is aimed at reproducing the observed thermal hydraulic behavior in a pressurization transient. Measured core power is an input to the calculation. Comparison with data show the code reasonably well predicts the generation and propagation of the pressure waves in the main steam line and associated pressurization of the reactor vessel following the closure of the turbine stop valve

Cuttings-liquid frictional pressure loss model for horizontal narrow annular flow with rotating drillpipe

International Nuclear Information System (INIS)

Ofei, T N; Irawan, S; Pao, W

2015-01-01

During oil and gas drilling operations, frictional pressure loss is experienced as the drilling fluid transports the drilled cuttings from the bottom-hole, through the annulus, to the surface. Estimation of these pressure losses is critical when designing the drilling hydraulic program. Two-phase frictional pressure loss in the annulus is very difficult to predict, and even more complex when there is drillpipe rotation. Accurate prediction will ensure that the correct equivalent circulating density (ECD) is applied in the wellbore to prevent formation fracture, especially in formations with narrow window between the pore pressure and fracture gradient. Few researchers have attempted to propose cuttings-liquid frictional pressure loss models, nevertheless, these models fail when they are applied to narrow wellbores such as in casing- while-drilling and slimhole applications. This study proposes improved cuttings-liquid frictional pressure loss models for narrow horizontal annuli with drillpipe rotation using Dimensional Analysis. Both Newtonian and non-Newtonian fluids were considered. The proposed model constants were fitted by generated data from a full-scale simulation study using ANSYS-CFX. The models showed improvement over existing cuttings-liquid pressure loss correlations in literature. (paper)

From Rindler horizon to mini black holes at LHC

Energy Technology Data Exchange (ETDEWEB)

Ghaffary, Tooraj [Islamic Azad University, Department of Science, Shiraz Branch, Shiraz (Iran, Islamic Republic of)

2017-02-15

Recently researchers (A. Sepehri et al., Astrophys. Space Sci. 344, 79 (2013)) have considered the signature of superstring balls near mini black holes at LHC and calculate the information loss for these types of strings. Motivated by their work, we consider the evolution of events in high energy experiments from lower energies for which the Rindler horizon is formed to higher energies in which mini black holes and string balls are emerged. Extending the Gottesman and Preskill method to string theory, we find the information loss for excited strings ''string balls'' in mini black holes at LHC and calculate the information transformation from the collapsing matter to the state of outgoing Hawking radiation for strings. We come to the conclusion that information transformation for high energy strings is complete. Then the thermal distribution of excited strings near mini black holes at LHC is calculated. In order to obtain the total string cross section near black holes produced in proton-proton collision, we multiply the black hole production cross section by the thermal distribution of strings. It is observed that many high energy excited strings are produced near the event horizon of TeV black holes. These excited strings evaporate to standard model particles like Higgs boson and top quark at Hagedorn temperature. We derive the production cross section for these particles due to string ball decay at LHC and consider their decay to light particles like bottom quarks and gluons. (orig.)

DOE HIGH-POWER SLIM-HOLE DRILLING SYSTEM

Energy Technology Data Exchange (ETDEWEB)

Dr. William C. Maurer; John H. Cohen; J. Chris Hetmaniak; Curtis Leitko

1999-09-01

This project used a systems approach to improve slim-hole drilling performance. A high power mud motor, having a double-length power section, and hybrid PDC/TSP drill bit were developed to deliver maximum horsepower to the rock while providing a long life down hole. This high-power slim-hole drilling system drills much faster than conventional slim-hole motor and bit combinations and holds significant potential to reduce slim-hole drilling costs. The oil and gas industries have been faced with downward price pressures since the 1980s. These pressures are not expected to be relieved in the near future. To maintain profitability, companies have had to find ways to reduce the costs of producing oil and gas. Drilling is one of the more costly operations in the production process. One method to reduce costs of drilling is to use smaller more mobile equipment. Slim holes have been drilled in the past using this principle. These wells can save money not only from the use of smaller drilling equipment, but also from reduced tubular costs. Stepping down even one casing size results in significant savings. However, slim holes have not found wide spread use for three reasons. First, until recently, the price of oil has been high so there were no forces to move the industry in this direction. Second, small roller bits and motors were not very reliable and they drilled slowly, removing much of the economic benefit. The third and final reason was the misconception that large holes were needed everywhere to deliver the desired production. Several factors have changed that will encourage the use of slim holes. The industry now favors any method of reducing the costs of producing oil and gas. In addition, the industry now understands that large holes are not always needed. Gas, in particular, can have high production rates in smaller holes. New materials now make it possible to manufacture improved bits and motors that drill for long periods at high rates. All that remains is to

The footprint of bottom trawling in European waters

NARCIS (Netherlands)

Eigaard, Ole R.; Bastardie, Francois; Hintzen, Niels T.; Buhl-Mortensen, Lene; Buhl-Mortensen, Pål; Catarino, Rui; Dinesen, Grete E.; Egekvist, Josefine; Fock, Heino O.; Geitner, Kerstin; Gerritsen, Hans D.; González, Manuel Marín; Jonsson, Patrik; Kavadas, Stefanos; Laffargue, Pascal; Lundy, Mathieu; Gonzalez-Mirelis, Genoveva; Nielsen, J.R.; Papadopoulou, Nadia; Posen, Paulette E.; Pulcinella, Jacopo; Russo, Tommaso; Sala, Antonello; Silva, Cristina; Smith, Christopher J.; Vanelslander, Bart; Rijnsdorp, Adriaan D.

2017-01-01

Mapping trawling pressure on the benthic habitats is needed as background to support an ecosystem approach to fisheries management. The extent and intensity of bottom trawling on the European continental shelf (0-1000 m) was analysed from logbook statistics and vessel monitoring system data for

Experimental investigation of slamming impact acted on flat bottom bodies and cumulative damage

Directory of Open Access Journals (Sweden)

Hyunkyoung Shin

2018-05-01

Full Text Available Most offshore structures including offshore wind turbines, ships, etc. suffer from the impulsive pressure loads due to slamming phenomena in rough waves. The effects of elasticity & plasticity on such slamming loads are investigated through wet free drop test results of several steel unstiffened flat bottom bodies in the rectangular water tank. Also, their cumulative deformations by consecutively repetitive free drops from 1000 mm to 2000 mm in height are measured. Keywords: Slamming phenomena, Impulsive pressure load, Wet free drop test, Flat bottom body, Cumulative damage

CMOS MEMS capacitive absolute pressure sensor

International Nuclear Information System (INIS)

Narducci, M; Tsai, J; Yu-Chia, L; Fang, W

2013-01-01

This paper presents the design, fabrication and characterization of a capacitive pressure sensor using a commercial 0.18 µm CMOS (complementary metal–oxide–semiconductor) process and postprocess. The pressure sensor is capacitive and the structure is formed by an Al top electrode enclosed in a suspended SiO 2 membrane, which acts as a movable electrode against a bottom or stationary Al electrode fixed on the SiO 2 substrate. Both the movable and fixed electrodes form a variable parallel plate capacitor, whose capacitance varies with the applied pressure on the surface. In order to release the membranes the CMOS layers need to be applied postprocess and this mainly consists of four steps: (1) deposition and patterning of PECVD (plasma-enhanced chemical vapor deposition) oxide to protect CMOS pads and to open the pressure sensor top surface, (2) etching of the sacrificial layer to release the suspended membrane, (3) deposition of PECVD oxide to seal the etching holes and creating vacuum inside the gap, and finally (4) etching of the passivation oxide to open the pads and allow electrical connections. This sensor design and fabrication is suitable to obey the design rules of a CMOS foundry and since it only uses low-temperature processes, it allows monolithic integration with other types of CMOS compatible sensors and IC (integrated circuit) interface on a single chip. Experimental results showed that the pressure sensor has a highly linear sensitivity of 0.14 fF kPa −1 in the pressure range of 0–300 kPa. (paper)

The analysis of bottom forming process for hybrid heating device

Science.gov (United States)

Bałon, Paweł; Świątoniowski, Andrzej; Kiełbasa, Bartłomiej

2017-10-01

In this paper the authors present an unusual method for bottom forming applicable for various industrial purposes including the manufacture of water heaters or pressure equipment. This method allows for the fabrication of the bottom of a given piece of stainless steel into a pre-determined shape conforming to the DIN standard which determines the most advantageous dimensions for the bottom cross section in terms of working pressure loading. The authors checked the validity of the method in a numerical and experimental way generating a tool designed to produce bottoms of specified geometry. Many problems are encountered during the design and production of parts, especially excessive sheet wrinkling over a large area of the part. The experiment showed that a lack of experience and numerical analysis in the design of such elements would result in the production of highly wrinkled parts. This defect would render the parts impossible to assemble with the cylindrical part. Many tool shops employ a method for drawing elements with a spherical surface which involves additional spinning, stamping, and grading operations, which greatly increases the cost of parts production. The authors present and compare two forming methods for spherical and parabolic objects, and experimentally confirm the validity of the sheet reversing method with adequate pressure force. The applied method produces parts in one drawing operation and in a following operation that is based on laser or water cutting to obtain a round blank. This reduces the costs of tooling manufacturing by requiring just one tool which can be placed on any hydraulic press with a minimum force of 2 000 kN.

Density of basalt core from Hilo drill hole, Hawaii

Science.gov (United States)

Moore, J.G.

2001-01-01

Density measurements of 1600 samples of core from 889 to 3097 m depth below sea level in the Hawaii Scientific Drilling Program hole near Hilo, Hawaii show marked differences between the basaltic rock types and help define stratigraphy in the hole. Water-saturated densities of subaerial lava flows (occurring above 1079 m depth) have the broadest range because of the large density variation within a single lava flow. Water-saturated densities commonly range from 2.0 to 3.0 with an average of 2.55 ?? 0.24 g/cc. Dikes and sills range from 2.8 to 3.1 g/cc). Densities of hyaloclastite commonly range from 2.3 to 2.7, with an overall average of about 2.5 g/cc. The low-density of most hyaloclastite is due primarily to palagonitization of abundant glass and presence of secondary minerals in the interstices between fragments. Four principal zones of pillow lava, separated by hyaloclastite, occur in the drill core. The shallowest (1983-2136 m) is paradoxically the densest, averaging 3.01 ?? 0.10 g/cc. The second (2234-2470 m) is decidedly the lightest, averaging 2.67 ?? 0.13 g/cc. The third (2640-2790 m) and fourth (2918-bottom at 3097 m) are high, averaging 2.89 ?? 0.17 and 2.97 ?? 0.08 g/cc, respectively. The first pillow zone includes degassed pillows i.e. lava erupted on land that flowed into the sea. These pillows are poor in vesicles, because the subaerial, one-atmosphere vesicles were compressed when the flow descended to deeper water and higher pressure. The second (low-density, non-degassed) pillow zone is the most vesicle-rich, apparently because it was erupted subaqueously at a shallow depth. The higher densities of the third and fourth zones result from a low vesicularity of only a few percent and an olivine content averaging more than 5% for the third zone and about 10% for the fourth zone. The uppermost hyaloclastite extending about 400 m below the bottom of the subaerial basalt is poorly cemented and absorbs up to 6 wt% of water when immersed. Progressing

State-of-the-Art Report on Five-hole Pitot tube

Energy Technology Data Exchange (ETDEWEB)

Kwon, Hyuk; Hwang, D. H.; Seo, K. W

2007-03-15

Five-hole pitot tube is an effective detector that could measure a three dimensional average flow field on a complex geometry. At the present study, have been mainly used in the field of aerodynamics and nautics, the five-hole pitot tube is extensively investigated to apply on the nuclear engineering. Five-hole pitot tube could measure the three dimensional velocity to make use of a relationship between pressure energy and kinetic energy from Bernoulli's equation; therefore, the report shortly overviewed the definition, units, and transducers of pressure and then detaily was described about the pitot tube. For five-hole pitot tube, history, kinds and fabrication methods were briefly provided. The calibration methods for the five-hole pitot tube were deeply introduced in various methods according to simple concept but complex process. Additionally, causeses of detection errors and estimation of uncertainty were included in the present report. Optical measurement and how wire anemometers are difficult to detect the flow velocity under environmental such as tight lattice bundle geometry, dusty flow and high temperature fluid. One of alternatives to overcome the diffculty is the five-hole pitot tube.

State-of-the-Art Report on Five-hole Pitot tube

International Nuclear Information System (INIS)

Kwon, Hyuk; Hwang, D. H.; Seo, K. W.

2007-03-01

Five-hole pitot tube is an effective detector that could measure a three dimensional average flow field on a complex geometry. At the present study, have been mainly used in the field of aerodynamics and nautics, the five-hole pitot tube is extensively investigated to apply on the nuclear engineering. Five-hole pitot tube could measure the three dimensional velocity to make use of a relationship between pressure energy and kinetic energy from Bernoulli's equation; therefore, the report shortly overviewed the definition, units, and transducers of pressure and then detaily was described about the pitot tube. For five-hole pitot tube, history, kinds and fabrication methods were briefly provided. The calibration methods for the five-hole pitot tube were deeply introduced in various methods according to simple concept but complex process. Additionally, causeses of detection errors and estimation of uncertainty were included in the present report. Optical measurement and how wire anemometers are difficult to detect the flow velocity under environmental such as tight lattice bundle geometry, dusty flow and high temperature fluid. One of alternatives to overcome the diffculty is the five-hole pitot tube

Hydrostatic-pressure effects on the correlated electron-hole transition energies in GaAs-Ga{sub 1-x}Al{sub x}As semiconductor quantum wells

Energy Technology Data Exchange (ETDEWEB)

Raigoza, N. [Instituto de Fisica, Universidad de Antioquia, AA 1226, Medellin (Colombia); Instituto de Fisica, Unicamp, CP 6165, Campinas, Sao Paulo, 13083-970 (Brazil); Duque, C.A. [Instituto de Fisica, Universidad de Antioquia, AA 1226, Medellin (Colombia); Reyes-Gomez, E. [Dept. of Theor. Physics, Univ. of Havana, San Lazaro y L, Vedado 10400, Havana (Cuba); Instituto de Fisica, Unicamp, CP 6165, Campinas, Sao Paulo, 13083-970 (Brazil); Oliveira, L.E. [Instituto de Fisica, Unicamp, CP 6165, Campinas, Sao Paulo, 13083-970 (Brazil)

2006-03-01

The effects of hydrostatic pressure on the correlated e-h transition energies in single GaAs-Ga{sub 1-x}Al{sub x}As quantum wells are calculated via a variational procedure, in the framework of the effective-mass and non-degenerate parabolic-band approximations. The valence-band anisotropy is included in our theoretical model by using different hole masses in different spatial directions. Both heavy- and light-hole exciton energies are obtained, and correlated e-h transition energies are found in good agreement with available experimental measurements. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Phase transition and entropy inequality of noncommutative black holes in a new extended phase space

Energy Technology Data Exchange (ETDEWEB)

Miao, Yan-Gang; Xu, Zhen-Ming, E-mail: miaoyg@nankai.edu.cn, E-mail: xuzhenm@mail.nankai.edu.cn [School of Physics, Nankai University, Tianjin 300071 (China)

2017-03-01

We analyze the thermodynamics of the noncommutative high-dimensional Schwarzschild-Tangherlini AdS black hole with the non-Gaussian smeared matter distribution by regarding a noncommutative parameter as an independent thermodynamic variable named as the noncommutative pressure . In the new extended phase space that includes this noncommutative pressure and its conjugate variable, we reveal that the noncommutative pressure and the original thermodynamic pressure related to the negative cosmological constant make the opposite effects in the phase transition of the noncommutative black hole, i.e. the former dominates the UV regime while the latter does the IR regime, respectively. In addition, by means of the reverse isoperimetric inequality, we indicate that only the black hole with the Gaussian smeared matter distribution holds the maximum entropy for a given thermodynamic volume among the noncommutative black holes with various matter distributions.

Recovery and Lithologic Analysis of Sediment from Hole UT-GOM2-1-H002, Green Canyon 955, Northern Gulf of Mexico

Science.gov (United States)

Kinash, N.; Cook, A.; Sawyer, D.; Heber, R.

2017-12-01

In May 2017 the University of Texas led a drilling and pressure coring expedition in the northern Gulf of Mexico, UT-GOM2-01. The holes were located in Green Canyon Block 955, where the Gulf of Mexico Joint Industry Project Leg II identified an approximately 100m thick hydrate-filled course-grained levee unit in 2009. Two separate wells were drilled into this unit: Holes H002 and H005. In Hole H002, a cutting shoe drill bit was used to collect the pressure cores, and only 1 of the 8 cores collected was pressurized during recovery. The core recovery in Hole H002 was generally poor, about 34%, while the only pressurized core had 45% recovery. In Hole H005, a face bit was used during pressure coring where 13 cores were collected and 9 cores remained pressurized. Core recovery in Hole H005 was much higher, at about 75%. The type of bit was not the only difference between the holes, however. Drilling mud was used throughout the drilling and pressure coring of Hole H002, while only seawater was used during the first 80m of pressure cores collected in Hole H005. Herein we focus on lithologic analysis of Hole H002 with the goal of documenting and understanding core recovery in Hole H002 to compare with Hole H005. X-ray Computed Tomography (XCT) images were collected by Geotek on pressurized cores, mostly from Hole H005, and at Ohio State on unpressurized cores, mostly from Hole H002. The XCT images of unpressurized cores show minimal sedimentary structures and layering, unlike the XCT images acquired on the pressurized, hydrate-bearing cores. Only small sections of the unpressurized cores remained intact. The unpressurized cores appear to have two prominent facies: 1) silt that did not retain original sedimentary fabric and often was loose within the core barrel, and 2) dense mud sections with some sedimentary structures and layering present. On the XCT images, drilling mud appears to be concentrated on the sides of cores, but also appears in layers and fractures within

Construction for holding together a cylindrical high pressure reactor vessel with hemispherical bottom and lid

International Nuclear Information System (INIS)

Desmarchais, W.E.; Braun, H.E.

1972-01-01

The construction shall prevent that in case of ruptures of the vessel rupture pieces may damage the secondary shielding system. The construction consists of two yokes fitting to the bottom and the lid of the vessel and held together by means of pull rods. The yokes are designed as truncated conshaped shells. The smaller end of the cone shells supports the hemispherical bottom and the lid of the vessel. The larger cone shell ends are tied together by the pull rods. As further improvements there may be arranged hemispherical protective shields between the hemispherical bottom and the lid of the vessel and the smaller end of the cone shells. (P.K.)

Thermodynamics of Horndeski black holes with non-minimal derivative coupling

Energy Technology Data Exchange (ETDEWEB)

Miao, Yan-Gang [Nankai University, School of Physics, Tianjin (China); Max-Planck-Institut fuer Gravitationsphysik (Albert-Einstein-Institut), Potsdam (Germany); Xu, Zhen-Ming [Nankai University, School of Physics, Tianjin (China)

2016-11-15

We explore thermodynamic properties of a new class of Horndeski black holes whose action contains a non-minimal kinetic coupling of a massless real scalar and the Einstein tensor. Our treatment is based on the well-accepted consideration, where the cosmological constant is dealt with as thermodynamic pressure and the mass of black holes as thermodynamic enthalpy. We resort to a newly introduced intensive thermodynamic variable, i.e., the coupling strength of the scalar and tensor whose dimension is length square, and thus yield both the generalized first law of thermodynamics and the generalized Smarr relation. Our result indicates that this class of Horndeski black holes presents rich thermodynamic behaviors and critical phenomena. Especially in the case of the presence of an electric field, these black holes undergo two phase transitions. Once the charge parameter exceeds its critical value, or the cosmological parameter does not exceed its critical value, no phase transitions happen and the black holes are stable. As a by-product, we point out, the coupling strength acts as the thermodynamic pressure in thermodynamics. (orig.)

Thermodynamics of Horndeski black holes with non-minimal derivative coupling

International Nuclear Information System (INIS)

Miao, Yan-Gang; Xu, Zhen-Ming

2016-01-01

We explore thermodynamic properties of a new class of Horndeski black holes whose action contains a non-minimal kinetic coupling of a massless real scalar and the Einstein tensor. Our treatment is based on the well-accepted consideration, where the cosmological constant is dealt with as thermodynamic pressure and the mass of black holes as thermodynamic enthalpy. We resort to a newly introduced intensive thermodynamic variable, i.e., the coupling strength of the scalar and tensor whose dimension is length square, and thus yield both the generalized first law of thermodynamics and the generalized Smarr relation. Our result indicates that this class of Horndeski black holes presents rich thermodynamic behaviors and critical phenomena. Especially in the case of the presence of an electric field, these black holes undergo two phase transitions. Once the charge parameter exceeds its critical value, or the cosmological parameter does not exceed its critical value, no phase transitions happen and the black holes are stable. As a by-product, we point out, the coupling strength acts as the thermodynamic pressure in thermodynamics. (orig.)

Pressure suppression device

International Nuclear Information System (INIS)

Mizumachi, Wataru; Fukuda, Akira; Kitaguchi, Hidemi; Shimizu, Toshiaki.

1976-01-01

Object: To relieve and absorb impact wave vibrations caused by steam and non-condensed gases releasing into the pressure suppression chamber at the time of an accident. Structure: The reactor container is filled with inert gases. A safety valve attached main steam pipe is provided to permit the excessive steam to escape, the valve being communicated with the pressure suppression chamber through an exhaust pipe. In the pressure suppression chamber, a doughnut-like cylindrical outer wall is filled at its bottom with pool water to condense the high temperature vapor released through the exhaust pipe. A head portion of a vent tube which leads the exhaust pipe is positioned at the top, and a down comer and an exhaust vent tube are locked by means of steady rests. At the bottom is mounted a pressure adsorber device which adsorbs a pressure from the pool water. (Kamimura, M.)

Hole burning with pressure and electric field: A window on the electronic structure and energy transfer dynamics of bacterial antenna complexes

Energy Technology Data Exchange (ETDEWEB)

Wu, H.M.

1999-02-12

Light-harvesting (LH) complexes of cyclic (C{sub n}) symmetry from photosynthetic bacteria are studied using absorption and high pressure- and Stark-hole burning spectroscopies. The B800 absorption band of LH2 is inhomogeneously broadened while the B850 band of LH2 and the B875 band of the LH1 complex exhibit significant homogeneous broadening due to ultra-fast inter-exciton level relaxation. The B800{r_arrow}B850 energy transfer rate of ({approximately}2 ps){sup {minus}1} as determined by hole burning and femtosecond pump-probe spectroscopies, is weakly dependent on pressure and temperature, both of which significantly affect the B800-B850 energy gap. The resilience is theoretically explained in terms of a modified Foerster theory with the spectral overlap provided by the B800 fluorescence origin band and weak vibronic absorption bands of B850. Possible explanations for the additional sub-picosecond relaxation channel of B800 observed with excitation on the blue side of B800 are given. Data from pressure and temperature dependent studies show that the B800 and B850 bacteriochlorophyll a (BChl a) molecules are weakly and strongly excitonically coupled, respectively, which is consistent with the X-ray structure of LH2. The B875 BChl a molecules are also strongly coupled. It is concluded that electron-exchange, in addition to electrostatic interactions, is important for understanding the strong coupling of the B850 and B875 rings. The large linear pressure shifts of {approximately}{minus}0.6 cm{sup {minus}1}/MPa associated with B850 and B875 can serve as important benchmarks for electronic structure calculations.

Nuclear reactor construction with bottom supported reactor vessel

International Nuclear Information System (INIS)

Sharbaugh, J.E.

1987-01-01

This patent describes an improved liquid metal nuclear reactor construction comprising: (a) a nuclear reactor core having a bottom platform support structure; (b) a reactor vessel for holding a large pool of low pressure liquid metal coolant and housing the core; (c) a containment structure surrounding the reactor vessel and having a sidewall spaced outwardly from the reactor vessel side wall and having a base mat spaced below the reactor vessel bottom end wall; (d) a central small diameter post anchored to the containment structure base mat and extending upwardly to the reactor vessel to axially fix the bottom end wall of the reactor vessel and provide a center column support for the lower end of the reactor core; (e) annular support structure disposed in the reactor vessel on the bottom end wall and extending about the lower end of the core; (f) structural support means disposed between the containment structure base mat and bottom end of the reactor vessel wall and cooperating for supporting the reactor vessel at its bottom end wall on the containment structure base mat to allow the reactor vessel to expand radially but substantially prevent any lateral motions that might be imposed by the occurrence of a seismic event; (g) a bed of insulating material disposed between the containment structure base mat and the bottom end wall of the reactor vessel and uniformly supporting the reactor vessel at its bottom end wall; freely expand radially from the central post as it heats up while providing continuous support thereof; (h) a deck supported upon the wall of the containment vessel above the top open end of the reactor vessel; and (i) extendible and retractable coupling means extending between the deck and the top open end of the reactor vessel and flexibly and sealably interconnecting the reactor vessel at its top end to the deck

Black hole chemistry: thermodynamics with Lambda

International Nuclear Information System (INIS)

Kubizňák, David; Mann, Robert B; Teo, Mae

2017-01-01

We review recent developments on the thermodynamics of black holes in extended phase space, where the cosmological constant is interpreted as thermodynamic pressure and treated as a thermodynamic variable in its own right. In this approach, the mass of the black hole is no longer regarded as internal energy, rather it is identified with the chemical enthalpy. This leads to an extended dictionary for black hole thermodynamic quantities; in particular a notion of thermodynamic volume emerges for a given black hole spacetime. This volume is conjectured to satisfy the reverse isoperimetric inequality—an inequality imposing a bound on the amount of entropy black hole can carry for a fixed thermodynamic volume. New thermodynamic phase transitions naturally emerge from these identifications. Namely, we show that black holes can be understood from the viewpoint of chemistry, in terms of concepts such as Van der Waals fluids, reentrant phase transitions, and triple points. We also review the recent attempts at extending the AdS/CFT dictionary in this setting, discuss the connections with horizon thermodynamics, applications to Lifshitz spacetimes, and outline possible future directions in this field. (topical review)

Black Hole Solution of Einstein-Born-Infeld-Yang-Mills Theory

Directory of Open Access Journals (Sweden)

Kun Meng

2017-01-01

Full Text Available A new four-dimensional black hole solution of Einstein-Born-Infeld-Yang-Mills theory is constructed; several degenerated forms of the black hole solution are presented. The related thermodynamical quantities are calculated, with which the first law of thermodynamics is checked to be satisfied. Identifying the cosmological constant as pressure of the system, the phase transition behaviors of the black hole in the extended phase space are studied.

Experimental Study of Injection Characteristics of a Multi-hole port injector on various Fuel Injection pressures and Temperatures

Directory of Open Access Journals (Sweden)

Ommi F

2013-04-01

Full Text Available The structures of the port injector spray dominates the mixture preparation process and strongly affect the subsequent engine combustion characteristics over a wide range of operating conditions in port-injection gasoline engines. All these spray characteristics are determined by particular injector design and operating conditions. In this paper, an experimental study is made to characterize the breakup mechanism and spray characteristics of a injector with multi-disc nozzle (SAGEM,D2159MA. A comparison was made on injection characteristics of the multi-hole injectors and its effects on various fuel pressure and temperature. The distributions of the droplet size and velocity and volume flux were characterized using phase Doppler anemometry (PDA technique. Through this work, it was found that the injector produces a finer spray with a wide spray angle in higher fuel pressure and temperature.

Experimental Study of Injection Characteristics of a Multi-hole port injector on various Fuel Injection pressures and Temperatures

Science.gov (United States)

Movahednejad, E.; Ommi, F.; Nekofar, K.

2013-04-01

The structures of the port injector spray dominates the mixture preparation process and strongly affect the subsequent engine combustion characteristics over a wide range of operating conditions in port-injection gasoline engines. All these spray characteristics are determined by particular injector design and operating conditions. In this paper, an experimental study is made to characterize the breakup mechanism and spray characteristics of a injector with multi-disc nozzle (SAGEM,D2159MA). A comparison was made on injection characteristics of the multi-hole injectors and its effects on various fuel pressure and temperature. The distributions of the droplet size and velocity and volume flux were characterized using phase Doppler anemometry (PDA) technique. Through this work, it was found that the injector produces a finer spray with a wide spray angle in higher fuel pressure and temperature.

Small break loss of coolant accidents: Bottom and side break

International Nuclear Information System (INIS)

Hardy, P.G.; Richter, H.J.

1987-01-01

A LOCA can be caused, e.g. by a small break in the primary cooling system. The rate of fluid escaping through such a break will define the time until the core will be uncovered. Therefore the prediction of fluid loss and pressure transient is of major importance to plan for timely action in response to such an event. Stratification of the two phases might be present upstream of the break, thus, the location of the break relative to the vapor-liquid interface and the overall upstream fluid conditions are relevant for the calculation of fluid loss. Experimental results and analyses are presented here for small breaks at the bottom or at the side of a small pressure vessel. It was found that in such a case the onset of the so-called ''vapor pull through'' is important but swelling at sufficient depressurization rates of the liquid due to flashing is also of significance. It was also discovered that in the bottom break the flow rate is strongly dependent on the break entrance quality of the vapour-liquid mixture. The side break can be treated similarly to the bottom break if the interface level is above the break. The analyses developed on the basis of experimental observations showed reasonable agreement of predicted and measured pressure transients. It was possible to calculate the changing interface level and mixture void fraction history in a way compatible with the behavior observed during the experiments. Even though the experiments were performed at low pressures, this work should help to get a better understanding of physical phenomena occurring in a full scale small break LOCA. (orig./HP)

Geology of drill hole UE25p No. 1: A test hole into pre-Tertiary rocks near Yucca Mountain, southern Nevada

International Nuclear Information System (INIS)

Carr, M.D.; Waddell, S.J.; Vick, G.S.; Stock, J.M.; Monsen, S.A.; Harris, A.G.; Cork, B.W.; Byers, F.M. Jr.

1986-01-01

Yucca Mountain in southern Nye County, Nevada, has been proposed as a potential site for the underground disposal of high-level nuclear waste. An exploratory drill hole designated UE25p No. 1 was drilled 3 km east of the proposed repository site to investigate the geology and hydrology of the rocks that underlie the Tertiary volcanic and sedimentary rock sequence forming Yucca Mountain. Silurian dolomite assigned to the Roberts Mountain and Lone Mountain Formations was intersected below the Tertiary section between a depth of approximately 1244 m (4080 ft) and the bottom of the drill hole at 1807 m (5923 ft). These formations are part of an important regional carbonate aquifer in the deep ground-water system. Tertiary units deeper than 1139 m (3733 ft) in drill hole UE25p No. 1 are stratigraphically older than any units previously penetrated by drill holes at Yucca Mountain. These units are, in ascending order, the tuff of Yucca Flat, an unnamed calcified ash-flow tuff, and a sequence of clastic deposits. The upper part of the Tertiary sequence in drill hole UE25p No. 1 is similar to that found in other drill holes at Yucca Mountain. The Tertiary sequence is in fault contact with the Silurian rocks. This fault between Tertiary and Paleozoic rocks may correlate with the Fran Ridge fault, a steeply westward-dipping fault exposed approximately 0.5 km east of the drill hole. Another fault intersects UE25p No. 1 at 873 m (2863 ft), but its surface trace is concealed beneath the valley west of the Fran Ridge fault. The Paintbrush Canyon fault, the trace of which passes less than 100 m (330 ft) east of the drilling site, intersects drill hole UE25p No. 1 at a depth of approximately 78 m (255 ft). The drill hole apparently intersected the west flank of a structural high of pre-Tertiary rocks, near the eastern edge of the Crater Flat structural depression

Drilling history core hole DC-4

International Nuclear Information System (INIS)

1978-12-01

Core hole DC-4 was completed at a depth of 3998 feet in December, 1978 by Boyles Brothers Drilling Company, Spokane, Washington, under subcontract to Fenix and Scission, Inc. The hole was cored for the US Department of Energy and the Rockwell Hanford Operations' Basalt Waste Isolation Program. Fenix and Sicsson, Inc. furnished the engineering, daily supervision of the cable tool and core drilling activities, and geological core logging for DC-4. Core hole DC-4 is located on the Hanford Site about 3 miles east of the Yakima Barricade and approximately 103 feet southwest of rotary hole DC-5, which was completed to 3990 feet in February, 1978. Hanford Site coordinates reported for hole DC-4 are north 49,385.62 feet and west 85,207.63 feet, and Washington State coordinates are north 454,468.73 feet and east 2,209,990.87 feet. No elevation survey is available for hole DC-4, but it is approximately 745 feet above mean sea level based upon the survey of hole DC-5, which has a reported elevation of 745.16 feet on the top of the 3-inch flange. The purpose of core hole DC-4 was to core drill vertically through the basalt and interbed units for stratigraphic depth determination and core collection, and to provide a borehole for hydrologic testing, cross-hole seismic shear, and pressure wave velocity studies with rotary hole DC-5. Hole DC-4 was drilled through the overburden into basalt bedrock by cable tool methods (0-623 feet) and continuously cored through the final interval (623 to 3998 feet).Core recovery was 95.8 percent of the total footage cored

Enthalpy and the mechanics of AdS black holes

International Nuclear Information System (INIS)

Kastor, David; Traschen, Jennie; Ray, Sourya

2009-01-01

We present geometric derivations of the Smarr formula for static AdS black holes and an expanded first law that includes variations in the cosmological constant. These two results are further related by a scaling argument based on Euler's theorem. The key new ingredient in the constructions is a two-form potential for the static Killing field. Surface integrals of the Killing potential determine the coefficient of the variation of Λ in the first law. This coefficient is proportional to a finite, effective volume for the region outside the AdS black hole horizon, which can also be interpreted as minus the volume excluded from a spatial slice by the black hole horizon. This effective volume also contributes to the Smarr formula. Since Λ is naturally thought of as a pressure, the new term in the first law has the form of effective volume times change in pressure that arises in the variation of the enthalpy in classical thermodynamics. This and related arguments suggest that the mass of an AdS black hole should be interpreted as the enthalpy of the spacetime.

Electron and hole photoemission detection for band offset determination of tunnel field-effect transistor heterojunctions

International Nuclear Information System (INIS)

Li, Wei; Zhang, Qin; Kirillov, Oleg A.; Levin, Igor; Richter, Curt A.; Gundlach, David J.; Nguyen, N. V.; Bijesh, R.; Datta, S.; Liang, Yiran; Peng, Lian-Mao; Liang, Xuelei

2014-01-01

We report experimental methods to ascertain a complete energy band alignment of a broken-gap tunnel field-effect transistor based on an InAs/GaSb hetero-junction. By using graphene as an optically transparent electrode, both the electron and hole barrier heights at the InAs/GaSb interface can be quantified. For a Al 2 O 3 /InAs/GaSb layer structure, the barrier height from the top of the InAs and GaSb valence bands to the bottom of the Al 2 O 3 conduction band is inferred from electron emission whereas hole emissions reveal the barrier height from the top of the Al 2 O 3 valence band to the bottom of the InAs and GaSb conduction bands. Subsequently, the offset parameter at the broken gap InAs/GaSb interface is extracted and thus can be used to facilitate the development of predicted models of electron quantum tunneling efficiency and transistor performance

Discharge Coefficient Measurements for Flow Through Compound-Angle Conical Holes with Cross-Flow

Directory of Open Access Journals (Sweden)

M. E. Taslim

2004-01-01

Full Text Available Diffusion-shaped film holes with compound angles are currently being investigated for high temperature gas turbine airfoil film cooling. An accurate prediction of the coolant blowing rate through these film holes is essential in determining the film effectiveness. Therefore, the discharge coefficients associated with these film holes for a range of hole pressure ratios is essential in designing airfoil cooling circuits. Most of the available discharge coefficient data in open literature has been for cylindrical holes. The main objective of this experimental investigation was to measure the discharge coefficients for subsonic as well as supersonic pressure ratios through a single conical-diffusion hole. The conical hole has an exit-to-inlet area ratio of 4, a nominal flow length-to-inlet diameter ratio of 4, and an angle with respect to the exit plane (inclination angle of 0°, 30°, 45°, and 60°. Measurements were performed with and without a cross-flow. For the cases with a cross-flow, discharge coefficients were measured for each of the hole geometries and 5 angles between the projected conical hole axis and the cross-flow direction of 0°, 45°, 90°, 135°, and 180°. Results are compared with available data in open literature for cylindrical film holes as well as limited data for conical film holes.

Load capacity of a thick-walled cylinder with a radial hole

International Nuclear Information System (INIS)

Laczek, S.; Rys, J.; Zielinski, A.P.

2010-01-01

The paper deals with elastic-plastic analysis of the stress-strain state in the vicinity of a hole in a thick-walled cylindrical pressure vessel. The investigations have been inspired by the phenomenon of ductile fracture observed in a high-pressure reactor. Using finite element calculations, different failure criteria are proposed to aid design and control of high-pressure vessels with piping attachments. They are compared with suggestions of American (ASME) and European (EN) standards. A simple shakedown analysis of the structure is also presented. The local stress distribution near the hole results in a specific failure of the vessel. A plastic zone appears in the vicinity of the internal cylinder surface and propagates along the hole side. The vessel unloading can cause local reverse plasticity, which leads to plastic shakedown in the small zone and then to progressive ductile fracture in this zone. This is dangerous for the whole structure.

Investigating Dark Energy with Black Hole Binaries

International Nuclear Information System (INIS)

Mersini-Houghton, Laura; Kelleher, Adam

2009-01-01

The accelerated expansion of the universe is ascribed to the existence of dark energy. Black holes accrete dark energy. The accretion induces a mass change proportional to the energy density and pressure of the background dark energy fluid. The time scale during which the mass of black holes changes considerably is long relative to the age of the universe, thus beyond detection possibilities. We propose to take advantage of the modified black hole masses for exploring the equation of state w[z] of dark energy, by investigating the evolution of supermassive black hole binaries on a dark energy background. Deriving the signatures of dark energy accretion on the evolution of binaries, we find that dark energy imprints on the emitted gravitational radiation and on the changes in the orbital radius of the binary can be within detection limits for certain supermassive black hole binaries. This talk describes how binaries can provide a useful tool in obtaining complementary information on the nature of dark energy.

Materials and mechanisms of hole superconductivity

Energy Technology Data Exchange (ETDEWEB)

Hirsch, J.E., E-mail: jhirsch@ucsd.edu [Department of Physics, University of California, San Diego, La Jolla, CA 92093-0319 (United States)

2012-01-15

We study the applicability of the model of hole superconductivity to materials. Both conventional and unconventional materials are considered. Many different classes of materials are discussed. The theory is found suitable to describe all of them. No other theory of superconductivity can describe all these classes of materials. The theory of hole superconductivity proposes that there is a single mechanism of superconductivity that applies to all superconducting materials. This paper discusses several material families where superconductivity occurs and how they can be understood within this theory. Materials discussed include the elements, transition metal alloys, high T{sub c} cuprates both hole-doped and electron-doped, MgB{sub 2}, iron pnictides and iron chalcogenides, doped semiconductors, and elements under high pressure.

New system for measuring and controlling the maximum pressing pressure in the holes of the mould: ISOPRESS; Nuevo sistema para la medida y control de la presion maxima de prensado en los alveolos del molde: ISOPRESS

Energy Technology Data Exchange (ETDEWEB)

Poyatos, A.; Bonaque, R.; Mallol, G.; Boix, J.

2012-07-01

The organization MACER, in collaboration with the Institute of Ceramic Technology, has developed the system ISOPRESS, an integrated control device that permits to equal automatically the maximum pressure applied on the powder contained in each of the holes of the mould. This system consists of a set of pressure transducers which are located in the isostatic punches of the mould itself. With them it is possible to register in real-time the evolution of the measured pressure of the oil contained in the compensation chamber of each punch. All the transducers are connected to a data acquisition system which transfers the pressure values to a PC which performs the signal processing to obtain the pressure maximum value reached during a pressing cycle, in each one of the holes. The system is completed with a control software especially developed, that permits to regulate individually the height of the first fall of each inferior punch to guarantee the uniformity of the pressure applied in all the holes. ISOPRESS, by assuring the constancy of the bulk density of all the pieces processed, guarantees a unique piece size and minimize production problems associated to the variability of the bulk density of the pieces. (Author)

A Long-Term Geothermal Observatory Spanning Subseafloor Gas Hydrates in IODP Hole U1364A, Cascadia Accretionary Prism

Science.gov (United States)

Becker, K.; Davis, E.; Heesemann, M.; McGuire, J. J.; Collins, J. A.; O'Brien, J. K.; von der Heydt, K.

2017-12-01

We report the configuration of and initial results from a 24-thermistor cable installed to 268 m below seafloor (mbsf) in IODP Hole U1364A in the frontal accretionary prism of the Cascadia subduction zone. The thermistor array spans the gas hydrate stability zone and a clear bottom-simulating reflector at 225-230 mbsf. The thermistor string was deployed in July 2016 along with a seismic-strain observatory into the cased section of a pressure-monitoring Advanced CORK (ACORK) that had been installed in 2010 during IODP Expedition 328. Formation pressures are monitored via permeable screens on the outside of solid steel casing that is sealed at the bottom by a bridge plug and cement up to 302 mbsf. All three observatory systems were connected to the Ocean Networks Canada NEPTUNE cabled observatory Clayoquot Slope node in June of 2017, with the thermistor temperatures being logged by ONC every minute. The thermistor array was designed with concentrated vertical spacing around the BSR and two pressure-monitoring screens at 203 and 244 mbsf, with wider thermistor spacing elsewhere to document the geothermal state up to seafloor. The initial six weeks of data logged via the ONC connection show a generally linear temperature gradient, with temperatures of about 15.8°C at the BSR depth, consistent with methane hydrate stability at that depth and pressure. Sensor temperatures at most depths are quite stable over this period, with the exceptions of two sensors at 76 and 256 mbsf that show slowly rising temperatures; these could be due to cellular convection of borehole fluids, sensor degradation, or formation processes, but this requires a longer time series to resolve. We will report updated results after four more months of data recording through November 2017, along with any correlations to the pressure records. The data are freely available to all registered ONC users via the ONC data management and archiving system.

The desorption of caesium from Peach Bottom HTGR steam generator materials

International Nuclear Information System (INIS)

Clark, M.J.

1979-03-01

The work at Harwell on the Peach Bottom End-of-Life Program in co-operation with the General Atomic Company (U.S.A.) is described. Materials taken from the Economiser, Evaporator and Superheater Sections of the Peach Bottom Unit No. 1. High Temperature Gas Cooled Reactor (HTGR) Heat Exchanger were placed in a reducing atmosphere comparable to the composition of an HTGR helium coolant gas, and the desorption of caesium isotopes measured under known conditions of flow, temperature and oxygen pressure. (author)

Bottom head assembly

International Nuclear Information System (INIS)

Fife, A.B.

1998-01-01

A bottom head dome assembly is described which includes, in one embodiment, a bottom head dome and a liner configured to be positioned proximate the bottom head dome. The bottom head dome has a plurality of openings extending there through. The liner also has a plurality of openings extending there through, and each liner opening aligns with a respective bottom head dome opening. A seal is formed, such as by welding, between the liner and the bottom head dome to resist entry of water between the liner and the bottom head dome at the edge of the liner. In the one embodiment, a plurality of stub tubes are secured to the liner. Each stub tube has a bore extending there through, and each stub tube bore is coaxially aligned with a respective liner opening. A seat portion is formed by each liner opening for receiving a portion of the respective stub tube. The assembly also includes a plurality of support shims positioned between the bottom head dome and the liner for supporting the liner. In one embodiment, each support shim includes a support stub having a bore there through, and each support stub bore aligns with a respective bottom head dome opening. 2 figs

THE EFFECTS OF SWIRL GENERATOR HAVING WINGS WITH HOLES ON HEAT TRANSFER AND PRESSURE DROP IN TUBE HEAT EXCHANGER

Directory of Open Access Journals (Sweden)

Zeki ARGUNHAN

2006-02-01

Full Text Available This paper examines the effect of turbulance creators on heat transfer and pressure drop used in concentric heat exchanger experimentaly. Heat exchanger has an inlet tube with 60 mm in diameter. The angle of swirl generators wings is 55º with each wing which has single, double, three and four holes. Swirl generators is designed to easily set to heat exchanger entrance. Air is passing through inner tube of heat exhanger as hot fluid and water is passing outer of inner tube as cool fluid.

Inservice inspection of Halden BWR pressure vessel

International Nuclear Information System (INIS)

Foerli, O.; Hernes, T.

1978-01-01

A description is given of how the recertification inspection of the 20 years old Halden Reactor pressure vessel was carried out in accordance with the latest ASME-CODES, despite the fact that inspection accessibility was poor. As no volumetric inspection had been carried out since the preservice radiography in 1957, the ultrasonic inspection included the high flux region of all welds. In total 70% of longitudinal welds and 20% of bottom circumferential welds were inspected as well as the bottom nozzle connection. The vessel was not designed with provisions for inservice inspection, the welds are unaccessible from the outside and removal of the lid is virtually impossible. The ultrasonic probes could only be loaded through 77 mm diameter holes in the top lid and remotely positioned inside the vessel. The inspection was performed using 450C and 60OC 1 MHz angle probes and 2.25 MHz normal probes in immersion technique. In a zone around the welds, small regions with lack of bonding between the stainless steel cladding and the boiler steel were revealed. One root defect known and accepted from the preservice radiographs was examined. The defect was found to be 6x30mm as a maximum and well within acceptable limits according to the fracture mechanics analysis method recommended in ASME X1. The inspection required a period of three weeks' work in the reactor hall. (UK)

Conceptual Design of Bottom-mounted Control Rod Drive Mechanism

International Nuclear Information System (INIS)

Lee, Jin Haeng; Kim, Sanghaun; Yoo, Yeonsik; Cho, Yeonggarp; Kim, Dongmin; Kim, Jong In

2013-01-01

The arrangement of the BMCRDMs and irradiation holes in the core is therefore easier than that of the top-mounted CRDM. Hence, many foreign research reactors, such as JRR-3M, JMTR, OPAL, and CARR, have adopted the BMCRDM concept. The purpose of this paper is to introduce the basic design concept on the BMCRDM. The major differences of the CRDMs between HANARO and KJRR are compared, and the design features and individual system of the BMCRDM for the KJRR are described. The Control Rod Drive Mechanism (CRDM) is a device to regulate the reactor power by changing the position of a Control Absorber Rod (CAR) and to shut down the reactor by fully inserting the CAR into the core within a specified time. The Bottom-Mounted CRDM (BMCRDM) for the KiJang Research Reactor (KJRR) is a quite different design concept compared to the top-mounted CRDM such as HANARO and JRTR. The main drive mechanism of the BMCRDM is located in a Reactivity Control Mechanism (RCM) room under the reactor pool bottom, which makes the interference with equipment in the reactor pool reduced

Conceptual Design of Bottom-mounted Control Rod Drive Mechanism

Energy Technology Data Exchange (ETDEWEB)

Lee, Jin Haeng; Kim, Sanghaun; Yoo, Yeonsik; Cho, Yeonggarp; Kim, Dongmin; Kim, Jong In [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-05-15

The arrangement of the BMCRDMs and irradiation holes in the core is therefore easier than that of the top-mounted CRDM. Hence, many foreign research reactors, such as JRR-3M, JMTR, OPAL, and CARR, have adopted the BMCRDM concept. The purpose of this paper is to introduce the basic design concept on the BMCRDM. The major differences of the CRDMs between HANARO and KJRR are compared, and the design features and individual system of the BMCRDM for the KJRR are described. The Control Rod Drive Mechanism (CRDM) is a device to regulate the reactor power by changing the position of a Control Absorber Rod (CAR) and to shut down the reactor by fully inserting the CAR into the core within a specified time. The Bottom-Mounted CRDM (BMCRDM) for the KiJang Research Reactor (KJRR) is a quite different design concept compared to the top-mounted CRDM such as HANARO and JRTR. The main drive mechanism of the BMCRDM is located in a Reactivity Control Mechanism (RCM) room under the reactor pool bottom, which makes the interference with equipment in the reactor pool reduced.

The design and construction of the bottom working for in-situ leaching of fragmented uranium ore by blasting in No. 745 mine

International Nuclear Information System (INIS)

Ding Dexin; Yang Shijiao; Li Ming

1998-11-01

Bottom working is a very important structure for in-situ leaching of fragmented uranium ore by blasting. Its design and construction should simultaneously satisfy the requirements for receiving fragmented ore, transporting the ore, providing relief space for blast operation, passage for workers and fresh air for the slope and collecting the pregnant solution from spraying over the fragmented ore. The author deals with the design and construction of the complete water cutoff bottom working for collecting the pregnant solution for in-situ leaching of fragmented uranium ore by long hole blast in No. 745 mine in Guangdong Province. The preparation system for the block, the undercutting, the construction process and method of the bottom working and the measures to guide the solution leaked into the surrounding rock mass to the bottom of the block are described in detail

Bottom head failure program plan

International Nuclear Information System (INIS)

Meyer, R.O.

1989-01-01

Earlier this year the NRC staff presented a Revised Severe Accident Research Program Plan (SECY-89-123) to the Commission and initiated work on that plan. Two of the near-term issues in that plan involve failure of the bottom head of the reactor pressure vessel. These two issues are (1) depressurization and DCH and (2) BWR Mark I Containment Shell Meltthrough. ORNL has developed models for several competing failure mechanisms for BWRs. INEL has performed analytical and experimental work directly related to bottom head failure in connection with several programs. SNL has conducted a number of analyses and experimental activities to examine the failure of LWR vessels. In addition to the government-sponsored work mentioned above, EPRI and FAI performed studies on vessel failure for the Industry Degraded Core Rulemaking Program (IDCOR). EPRI examined the failure of a PWR vessel bottom head without penetrations, as found in some Combustion Engineering reactors. To give more attention to this subject as called for by the revised Severe Accident Research Plan, two things are being done. First, work previously done is being reviewed carefully to develop an overall picture and to determine the reliability of assumptions used in those studies. Second, new work is being planned for FY90 to try to complete a reasonable understanding of the failure process. The review and planning are being done in close cooperation with the ACRS. Results of this exercise will be presented in this paper

Nanocomposite-Based Microstructured Piezoresistive Pressure Sensors for Low-Pressure Measurement Range

Directory of Open Access Journals (Sweden)

Vasileios Mitrakos

2018-01-01

Full Text Available Piezoresistive pressure sensors capable of detecting ranges of low compressive stresses have been successfully fabricated and characterised. The 5.5 × 5 × 1.6 mm3 sensors consist of a planar aluminium top electrode and a microstructured bottom electrode containing a two-by-two array of truncated pyramids with a piezoresistive composite layer sandwiched in-between. The responses of two different piezocomposite materials, a Multiwalled Carbon Nanotube (MWCNT-elastomer composite and a Quantum Tunneling Composite (QTC, have been characterised as a function of applied pressure and effective contact area. The MWCNT piezoresistive composite-based sensor was able to detect pressures as low as 200 kPa. The QTC-based sensor was capable of detecting pressures as low as 50 kPa depending on the contact area of the bottom electrode. Such sensors could find useful applications requiring the detection of small compressive loads such as those encountered in haptic sensing or robotics.

White holes and eternal black holes

International Nuclear Information System (INIS)

Hsu, Stephen D H

2012-01-01

We investigate isolated white holes surrounded by vacuum, which correspond to the time reversal of eternal black holes that do not evaporate. We show that isolated white holes produce quasi-thermal Hawking radiation. The time reversal of this radiation, incident on a black hole precursor, constitutes a special preparation that will cause the black hole to become eternal. (paper)

Hierarchical Model for the Similarity Measurement of a Complex Holed-Region Entity Scene

Directory of Open Access Journals (Sweden)

Zhanlong Chen

2017-11-01

Full Text Available Complex multi-holed-region entity scenes (i.e., sets of random region with holes are common in spatial database systems, spatial query languages, and the Geographic Information System (GIS. A multi-holed-region (region with an arbitrary number of holes is an abstraction of the real world that primarily represents geographic objects that have more than one interior boundary, such as areas that contain several lakes or lakes that contain islands. When the similarity of the two complex holed-region entity scenes is measured, the number of regions in the scenes and the number of holes in the regions are usually different between the two scenes, which complicates the matching relationships of holed-regions and holes. The aim of this research is to develop several holed-region similarity metrics and propose a hierarchical model to measure comprehensively the similarity between two complex holed-region entity scenes. The procedure first divides a complex entity scene into three layers: a complex scene, a micro-spatial-scene, and a simple entity (hole. The relationships between the adjacent layers are considered to be sets of relationships, and each level of similarity measurements is nested with the adjacent one. Next, entity matching is performed from top to bottom, while the similarity results are calculated from local to global. In addition, we utilize position graphs to describe the distribution of the holed-regions and subsequently describe the directions between the holes using a feature matrix. A case study that uses the Great Lakes in North America in 1986 and 2015 as experimental data illustrates the entire similarity measurement process between two complex holed-region entity scenes. The experimental results show that the hierarchical model accounts for the relationships of the different layers in the entire complex holed-region entity scene. The model can effectively calculate the similarity of complex holed-region entity scenes, even if the

Chemical aspects of cylinder corrosion and a scenario for hole development

Energy Technology Data Exchange (ETDEWEB)

Barber, E.J. [Martin Marietta Energy Systems, Oak Ridge, TN (United States)

1991-12-31

In June 1990, two cylinders in the depleted UF{sub 6} cylinder storage yards at Portsmouth were discovered to have holes in their walls at the valve-end stiffening ring at a point below the level of the gas-solid interface of the UF{sub 6}. The cylinder with the larger hole, which extended under the stiffening ring, was stacked in a top row 13 years ago. The cylinder with the smaller hole had been stacked in a bottom row 4 years ago. The lifting lugs of the adjacent cylinders pointed directly at the holes. A Cylinder Investigating Committee was appointed to determine the cause or causes of the holes and to assess the implications of these findings. This report contains a listing of the chemically related facts established by the Investigating Committee with the cooperation of the Operations and Technical Support Divisions at the Portsmouth Gaseous Diffusion Plant, the scenario developed to explain these findings and some implications of this scenario. In summary, the interrelated reactions of water, solid UF{sub 6} and iron presented by R. L. Ritter are used to develop a scenario which explains the observations and deductions made during the investigation. The chemical processes are intimately related to the course of the last three of the four stages of hole development. A simple model is proposed which permits semiquantitative prediction of such information as the HF loss rates as a function of time, the rate of hole enlargement, the time to hydrolyze a cylinder of UF{sub 6} and the approximate size of the hole. The scenario suggests that the environmental consequences associated with a developing hole in a depleted UF{sub 6} cylinder are minimal for the first several years but will become significant if too many years pass before detection. The overall environmental picture is presented in more detail elsewhere.

Black holes and structure in an oscillating universe

International Nuclear Information System (INIS)

Saslaw, W.C.

1991-01-01

If black holes exist in the contracting phase of a closed universe, they will give rise to a pressure and entropy catastrophe. First, the black holes absorb all the radiation; then their apparent horizons merge, and coalesce with the cosmological apparent horizon. All external observers become internal observers. It is possible that the internal metric of some of the merging black holes will be contracting, and others expanding. I suggest here that the resulting violent inhomogeneities can lead to a re-expansion in a significant portion of the universe. Global re-expansion, prompted by the merging of black holes, may thus begin in a semi-classical rather than fully quantum gravitational era, at densities greater than those at which nucleosynthesis occurs. Surviving black holes and inhomogeneities could initiate the formation of structures such as galaxies in the 'new' universe. The behaviour of such an oscillating universe would differ in detail from cycle to cycle. (author)

Relating follicly-challenged compact stars to bald black holes: A link between two no-hair properties

Science.gov (United States)

Yagi, Kent; Yunes, Nicolás

2015-05-01

Compact stars satisfy certain no-hair relations through which their multipole moments are given by their mass, spin and quadrupole moment. These relations are approximately independent of their equation of state, relating pressure to density. Such relations are similar to the black hole no-hair theorems, but these possess event horizons inside which information that led to their formation can hide. Compact stars do not possess horizons, so whether their no-hair relations are related to the black hole ones is unclear. We investigate how the two relations are related by studying relations among multipole moments for compact stars with anisotropic pressure as a toy model, which allows such stars to be more compact than those with isotropic pressure. We here show numerically that the compact star no-hair relations approach the black hole ones as the compactness approaches that of a black hole. We also prove analytically that the current dipole moment exactly reaches the black hole limit quadratically in compactness as strongly anisotropic stars approach the black hole limit. We moreover show that compact stars become progressively oblate in this limit, even if prolate at low compactness due to strong anisotropies.

Pressure loss coefficient and flow rate of side hole in a lower end plug for dual-cooled annular nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

Shin, Chang-Hwan, E-mail: shinch@kaeri.re.kr; Park, Ju-Yong, E-mail: juyong@kaeri.re.kr; In, Wang-Kee, E-mail: wkin@kaeri.re.kr

2013-12-15

Highlights: • A lower end plug with side flow holes is suggested to provide alternative flow paths of the inner channel. • The inlet loss coefficient of the lower end plug is estimated from the experiment. • The flow rate through the side holes is estimated in a complete entrance blockage of inner channel. • The consequence in the reactor core condition is evaluated with a subchannel analysis code. - Abstract: Dual-cooled annular nuclear fuel for a pressurized water reactor (PWR) has been introduced for a significant increase in reactor power. KAERI has been developing a dual-cooled annular fuel for a power uprate of 20% in an optimized PWR in Korea, the OPR1000. This annular fuel can help decrease the fuel temperature substantially relative to conventional cylindrical fuel at a power uprate. Annular fuel has dual flow channels around itself; however, the inner flow channel has a weakness in that it is isolated unlike the outer flow channel, which is open to other neighbouring outer channels for a coolant exchange in the reactor core. If the entrance of the inner channel is, as a hypothetical event, completely blocked by debris, the inner channel will then experience a rapid increase in coolant temperature such that a departure from nucleate boiling (DNB) may occur. Therefore, a remedy to avoid such a postulated accident is indispensable for the safety of annular fuel. A lower end plug with side flow holes was suggested to provide alternative flow paths in addition to the central entrance of the inner channel. In this paper, the inlet loss coefficient of the lower end plug and the flow rate through the side holes were estimated from the experimental results even in a complete entrance blockage of the inner channel. An optimization for the side hole was also performed, and the results are applied to a subchannel analysis to evaluate the consequence in the reactor core condition.

Numerical study of nonspherical black hole accretion

International Nuclear Information System (INIS)

Hawley, J.F.

1984-01-01

This thesis describes in detail a two-dimensional, axisymmetric computer code for calculating fully relativistic ideal gas hydrodynamics around a Kerr black hole. The aim is to study fully dynamic inviscid fluid accretion onto black holes, as well as to study the evolution and development of nonlinear instabilities in pressure supported accretion disks. In order to fully calibrate and document the code, certain analytic solutions for shock tubes and special accretion flows are derived; these solutions form the basis for code testing. The numerical techniques used are developed and discussed. A variety of alternate differencing schemes are compared on an analytic test bed. Some discussion is devoted to general issues in finite differencing. The working code is calibrated using analytically solvable accretion problems, including the radial accretion of dust and of fluid with pressure (Bondi accretion). Two dimensional test problems include the spiraling infall of low angular momentum fluid, the formation of a pressure supported torus, and the stable evolution of a torus. A series of numerical models are discussed and illustrated with selected plots

Black holes thermodynamics, information, and firewalls

CERN Document Server

Mann, Robert B

2015-01-01

This book reflects the resurgence of interest in the quantum properties of black holes, culminating most recently in controversial discussions about firewalls. On the thermodynamic side, it describes how new developments allowed the inclusion of pressure/volume terms in the first law, leading to a new understanding of black holes as chemical systems, experiencing novel phenomena such as triple points and reentrant phase transitions. On the quantum-information side, the reader learns how basic arguments undergirding quantum complementarity have been shown to be flawed; and how this suggests that a black hole may surround itself with a firewall: a violent and chaotic region of highly excited states. In this thorough and pedagogical treatment, Robert Mann traces these new developments from their roots to our present-day understanding, highlighting their relationships and the challenges they present for quantum gravity.

Hole-to-surface resistivity measurements at Gibson Dome (drill hole GD-1) Paradox basin, Utah

Science.gov (United States)

Daniels, J.J.

1984-01-01

Hole-to-surface resistivity measurements were made in a deep drill hole (GD-1), in San Juan County, Utah, which penetrated a sequence of sandstone, shale, and evaporite. These measurements were made as part of a larger investigation to study the suitability of an area centered around the Gibson Dome structure for nuclear waste disposal. The magnitude and direction of the total electric field resulting from a current source placed in a drill hole is calculated from potential difference measurements for a grid of closely-spaced stations. A contour map of these data provides a detailed map of the distribution of the electric field away from the drill hole. Computation of the apparent resistivity from the total electric field helps to interpret the data with respect to the ideal situation of a layered earth. Repeating the surface measurements for different source depths gives an indication of variations in the geoelectric section with depth. The quantitative interpretation of the field data at Gibson Dome was hindered by the pressure of a conductive borehole fluid. However, a qualitative interpretation of the field data indicates the geoelectric section around drill hole GD-1 is not perfectly layered. The geoelectric section appears to dip to the northwest, and contains anomalies in the resistivity distribution that may be representative of localized thickening or folding of the salt layers.

Flexible bottom-emitting white organic light-emitting diodes with semitransparent Ni/Ag/Ni anode.

Science.gov (United States)

Koo, Ja-Ryong; Lee, Seok Jae; Lee, Ho Won; Lee, Dong Hyung; Yang, Hyung Jin; Kim, Woo Young; Kim, Young Kwan

2013-05-06

We fabricated a flexible bottom-emitting white organic light-emitting diode (BEWOLED) with a structure of PET/Ni/Ag/Ni (3/6/3 nm)/ NPB (50 nm)/mCP (10 nm)/7% FIrpic:mCP (10 nm)/3% Ir(pq)(2) acac:TPBi (5 nm)/7% FIrpic:TPBi (5 nm)/TPBi (10 nm)/Liq (2 nm)/ Al (100 nm). To improve the performance of the BEWOLED, a multilayered metal stack anode of Ni/Ag/Ni treated with oxygen plasma for 60 sec was introduced into the OLED devices. The Ni/Ag/Ni anode effectively enhanced the probability of hole-electron recombination due to an efficient hole injection into and charge balance in an emitting layer. By comparing with a reference WOLED using ITO on glass, it is verified that the flexible BEWOLED showed a similar or better electroluminescence (EL) performance.

Bubble-induced mixing of two horizontal liquid layers with non-uniform gas injection at the bottom

International Nuclear Information System (INIS)

Cheung, F.B.; Leinweber, G.; Pedersen, D.R.

1984-01-01

During a postulated severe core meltdown accident in an LMFBR, a large amount of sodium coolant may spill into the reactor concrete cavity. A layer of liquid products may form as a result of the sodium-concrete reactions. The liquid product layer, which is highly viscous and much heavier than sodium, separates the concrete from the sodium pool. In general, the downward transport of sodium through the liquid product layer to the unreacted concrete surface, which controls the rate of chemical erosion of the concrete, depends strongly on the agitation induced by gas evolution from the heated concrete. In this study, experiments were conducted to explore the effect of non-uniform gas injection on mixing of two horizontal mutually soluble liquid layers. The liquid in the lower layer was chosen to be more viscous and heavier than the liquid in the upper layer. To simulate the reactor accident situation, gas was injected at the bottom of the liquid-liquid system through a circular hole that covered only the center portion of the bottom surface of the lower liquid layer. The bubble-induced mixing motions were observed and the rate of mixing was measured for different hole sizes and for various gas flow rates

Spray characteristics and liquid distribution of multi-hole effervescent atomisers for industrial burners

International Nuclear Information System (INIS)

Jedelský, Jan; Jícha, Miroslav

2016-01-01

Highlights: • The multi-hole (mh) spray morphology is very similar to that of single-hole nozzles. • Unsteady spray was found at low pressure and low gas-to-liquid-ratio (GLR) values. • Cone angle variation in mh spray with pressure and GLR depends on the exit nozzles angle. • A liquid–gas gravitational separation in horizontal atomiser operation was observed. • It causes up to 70% fuel supply variance into exit holes depending on design and regime. - Graphical Abstract: - Abstract: The present paper provides an experimental study and optimisation of multi-hole effervescent atomisers for industrial burners using oil-based fossil, bio- or waste fuels with prospects of emission reduction. Several multi-hole nozzles were designed based on our previous work. We probed the spray quality by phase-Doppler anemometry. 3-D plots of Sauter mean diameter and mean droplet velocity demonstrate their spatial distribution within the spray. The effect of geometrical and operational factors on the spray is discussed. Droplet size–velocity correlations as well as the size and velocity distributions are presented, and differences are found against other investigations. A spray macrostructure is photographically observed and spray cone angles of the multi-hole nozzles are analysed. An internal two-phase flow is estimated using the Baker's map for horizontal two-phase flow. Our previous two-phase flow visualisations suggested a liquid–gas gravitational separation when the multi-hole atomiser operated horizontally. This issue is addressed here; the results of spray heterogeneity measurements document that fuel flow rates through individual exit holes differ significantly. This difference spans between 0 and 70% depending on the nozzle design and flow regime. Effervescent sprays are unsteady under some operating conditions; spray unsteadiness was detected at low pressure and low gas-to-liquid-ratios.

A Black Hole Spectral Signature

Science.gov (United States)

Titarchuk, Lev; Laurent, Philippe

2000-03-01

An accreting black hole is, by definition, characterized by the drain. Namely, the matter falls into a black hole much the same way as water disappears down a drain matter goes in and nothing comes out. As this can only happen in a black hole, it provides a way to see ``a black hole'', an unique observational signature. The accretion proceeds almost in a free-fall manner close to the black hole horizon, where the strong gravitational field dominates the pressure forces. In this paper we present analytical calculations and Monte-Carlo simulations of the specific features of X-ray spectra formed as a result of upscattering of the soft (disk) photons in the converging inflow (CI) into the black hole. The full relativistic treatment has been implemented to reproduce these spectra. We show that spectra in the soft state of black hole systems (BHS) can be described as the sum of a thermal (disk) component and the convolution of some fraction of this component with the CI upscattering spread (Greens) function. The latter boosted photon component is seen as an extended power-law at energies much higher than the characteristic energy of the soft photons. We demonstrate the stability of the power spectral index over a wide range of the plasma temperature 0 - 10 keV and mass accretion rates (higher than 2 in Eddington units). We also demonstrate that the sharp high energy cutoff occurs at energies of 200-400 keV which are related to the average energy of electrons mec2 impinging upon the event horizon. The spectrum is practically identical to the standard thermal Comptonization spectrum when the CI plasma temperature is getting of order of 50 keV (the typical ones for the hard state of BHS). In this case one can see the effect of the bulk motion only at high energies where there is an excess in the CI spectrum with respect to the pure thermal one. Furthermore we demonstrate that the change of spectral shapes from the soft X-ray state to the hard X-ray state is clearly to be

Experimental Study on Environment Friendly Tap Hole Clay for Blast Furnace

Science.gov (United States)

Siva kumar, R.; Mohammed, Raffi; Srinivasa Rao, K.

2018-03-01

Blast furnace (BF) is the best possible route of iron production available. Blast furnace is a high pressure vessel where iron ore is melted and liquid iron is produced. The liquid iron is tapped through the hole in Blast Furnace called tap hole. The tapped liquid metal flowing through the tap hole is plugged using a clay called tap hole clay. Tap hole clay (THC) is a unshaped refractory used to plug the tap hole. The tap hole clay extruded through the tap hole using a gun. The tap hole clay is designed to expand and plug the tap hole. The tap hole filled with clay is drilled using drill bit and the hole made through the tap hole to tap the liquid metal accumulated inside the furnace. The number of plugging and drilling varies depending on the volume of the furnace. The tap hole clay need to have certain properties to avoid problems during plugging and drilling. In the present paper tap hole clay properties in industrial use was tested and studied. The problems were identified related to tap hole clay manufacturing. Experiments were conducted in lab scale to solve the identified problems. The present composition was modified with experimental results. The properties of the modified tap hole clay were found suitable and useful for blast furnace operation with lab scale experimental results.

Critical phenomena of static charged AdS black holes in conformal gravity

Directory of Open Access Journals (Sweden)

Wei Xu

2014-09-01

Full Text Available The extended thermodynamics of static charged AdS black holes in conformal gravity is analyzed. The P–V criticality of these black holes has some unusual features. There exists a single critical point with critical temperature Tc and critical pressure Pc. At fixed T>Tc (or at fixed P>Pc, there are two zeroth order phase transition points but no first order phase transition points. The systems favors large pressure states at constant T, or high temperature states at constant P.

Temperature buffer test. Installation of buffer, heaters and instruments in the deposition hole

Energy Technology Data Exchange (ETDEWEB)

Johannesson, Lars-Erik; Sanden, Torbjoern; Aakesson, Mattias [Clay Technology AB, Lund (Sweden); Barcena, Ignacio; Garcia-Sineriz, Jose Luis [Aitemin, Madrid (Spain)

2010-12-15

During 2003 the Temperature Buffer Test was installed in Aespoe Hard Rock Laboratory. Temperature, water pressure, relative humidity, total pressure and displacements etc. are measured in numerous points in the test. Most of the cables from the transducers are led in the deposition hole through slots in the rock surface of the deposition hole in watertight tubes to the data collection system in a container placed in the tunnel close to the deposition hole. This report describes the work with the installations of the buffer, heaters, and instruments and yields a description of the final location of all instruments. The report also contains a description of the materials that were installed and the densities yielded after placement.

Temperature buffer test. Installation of buffer, heaters and instruments in the deposition hole

International Nuclear Information System (INIS)

Johannesson, Lars-Erik; Sanden, Torbjoern; Aakesson, Mattias; Barcena, Ignacio; Garcia-Sineriz, Jose Luis

2010-12-01

During 2003 the Temperature Buffer Test was installed in Aespoe Hard Rock Laboratory. Temperature, water pressure, relative humidity, total pressure and displacements etc. are measured in numerous points in the test. Most of the cables from the transducers are led in the deposition hole through slots in the rock surface of the deposition hole in watertight tubes to the data collection system in a container placed in the tunnel close to the deposition hole. This report describes the work with the installations of the buffer, heaters, and instruments and yields a description of the final location of all instruments. The report also contains a description of the materials that were installed and the densities yielded after placement

Depth of array micro-holes with large aspect ratio in Al based cast alloy

Science.gov (United States)

Jin, Meiling; Qu, Yingdong; Li, Rongde

2018-03-01

In order to study on the depth of array micro-holes on Al base cast alloy, micro-hole with depth of 50 mm and diameter of 0.55 mm are successfully prepared by using poor wetting between carbon and Al. Accordingly, the mold of depth is established, the results show that calculated depth of micro-hole is 53.22 mm, relative error is 6% compare with the actual measured depth, and the depth of hole exponentially increases with the increasing of distance between two micro-holes. Surface tension and metallostatic pressure of metal molten are mainly affecting factors for depth of micro-holes.

Electron and Hole Transport Layers: Their Use in Inverted Bulk Heterojunction Polymer Solar Cells

Directory of Open Access Journals (Sweden)

Sandro Lattante

2014-03-01

Full Text Available Bulk heterojunction polymer solar cells (BHJ PSCs are very promising organic-based devices for low-cost solar energy conversion, compatible with roll-to-roll or general printing methods for mass production. Nevertheless, to date, many issues should still be addressed, one of these being the poor stability in ambient conditions. One elegant way to overcome such an issue is the so-called “inverted” BHJ PSC, a device geometry in which the charge collection is reverted in comparison with the standard geometry device, i.e., the electrons are collected by the bottom electrode and the holes by the top electrode (in contact with air. This reverted geometry allows one to use a high work function top metal electrode, like silver or gold (thus avoiding its fast oxidation and degradation, and eliminates the need of a polymeric hole transport layer, typically of an acidic nature, on top of the transparent metal oxide bottom electrode. Moreover, this geometry is fully compatible with standard roll-to-roll manufacturing in air and is less demanding for a good post-production encapsulation process. To date, the external power conversion efficiencies of the inverted devices are generally comparable to their standard analogues, once both the electron transport layer and the hole transport layer are fully optimized for the particular device. Here, the most recent results on this particular optimization process will be reviewed, and a general outlook regarding the inverted BHJ PSC will be depicted.

Analytical modeling of pressure transient behavior for coalbed methane transport in anisotropic media

International Nuclear Information System (INIS)

Wang, Lei; Wang, Xiaodong

2014-01-01

Resulting from the nature of anisotropy of coal media, it is a meaningful work to evaluate pressure transient behavior and flow characteristics within coals. In this article, a complete analytical model called the elliptical flow model is established by combining the theory of elliptical flow in anisotropic media and Fick's laws about the diffusion of coalbed methane. To investigate pressure transient behavior, analytical solutions were first obtained through introducing a series of special functions (Mathieu functions), which are extremely complex and are hard to calculate. Thus, a computer program was developed to establish type curves, on which the effects of the parameters, including anisotropy coefficient, storage coefficient, transfer coefficient and rate constant, were analyzed in detail. Calculative results show that the existence of anisotropy would cause great pressure depletion. To validate new analytical solutions, previous results were used to compare with the new results. It is found that a better agreement between the solutions obtained in this work and the literature was achieved. Finally, a case study is used to explain the effects of the parameters, including rock total compressibility coefficient, coal medium porosity and anisotropic permeability, sorption time constant, Langmuir volume and fluid viscosity, on bottom-hole pressure behavior. It is necessary to coordinate these parameters so as to reduce the pressure depletion. (paper)

FE-study for lithostatic pressure measurement in the 600 m borehole experiment

International Nuclear Information System (INIS)

Hamilton, L.F.M.; Benneker, P.B.J.M.

1990-05-01

In the Asse-2 salt mine an experiment is set up by ECN in the 600 m borehole to perform in-situ convergence measurements which can be used to validate or to determine the constitutive relations between stresses and deformations of the rocksalt. An experiment is planned in which the convergence of the borehole can be measured with different pressures created in the borehole. For this experiment a device has been developed at ECN which also will be used to measure the in-situ elasticity of the salt. This measuring device is designed in such a way that a pressure can be realized in the borehole and the deformation of the hole can be measured at the same time. In this report analyses are presented that are used to adjust the design of the pressure unit to the specific needs induced by the fact that the depth of the borehole is only 300 m due to drilling problems instead of the intended 600 m. Since the lithostatic pressure at this depth is smaller the convergence rate of the borehole is reduced. From the results presented in this report it can be concluded that it is not necessary to change the basic concept of the measurement as it was planned in the 600 m deep borehole. After the device has been placed into the borehole at a distance of 3 m from the bottom the empty space must be filled up with salt concrete up to 3 m above the pressure unit. In this way the interaction with the borehole bottom and the transition between the open and the filled borehole can be neglected. Some changes in the design are necessary to be able to measure the deformations of the borehole with enough accuracy. Based on these changes a measuring program has been defined in such a way that the experimental period is optimally used and the expected evolution of the volume change and pressure can be measured with enough accuracy. For three different constitutive models a prediction is made for the evolution of the pressure and the volume change resulting from the defined measuring program

Hole-Size Increasing PCFs for Blue-Extended Supercontinuum Generation

DEFF Research Database (Denmark)

Sørensen, Simon Toft; Larsen, Casper; Jakobsen, C.

2013-01-01

into the deep-blue in a single mode PCF with varying hole-size and pitch fabricated directly at the draw-tower. The PCFs in this work are fabricated by increasing the pressure on the air holes during the drawing. However, this process alone will lead to an undesirable structure where both the relative hole......Supercontinuum (SC) sources with spectra extending into the deep-blue region below 400 nm are highly desirable in areas such as fluorescent microscopy [1]. Tapering of photonic crystal fibers (PCFs) with high air-fill fractions has proven an effective way of extending the spectra into the deep...... wavelength spectral edge to wavelengths in the deep-blue or even UV. Previous reports on blue-extended SC generation were typically achieved in tapered PCFs where the air-hole structure was preserved [1-4], i.e. the relative hole-size constant. However, such PCFs with high air-fill fractions are inevitably...

Out-pile test of the capsule with cone shape bottom structures

Energy Technology Data Exchange (ETDEWEB)

Choi, M. H.; Kang, Y. H.; Cho, M. S.; Choo, K. N.; Kim, B. G.; Son, J. M.; Park, S. J.; Shin, Y. T.; Oh, J. M

2004-01-01

The design modification of bottom guide structures for the instrumented capsule which is used for the irradiation test in the research reactor, HANARO is done because of the cutting trouble of the bottom guide arm's pin. The previous structure of the 3-pin arm shape is changed into one body of the cone shape. The specimens of the bottom end cap ring with three different sizes ({phi}68mm, {phi}70mm, {phi}72mm) are designed and manufactured. The out-pile test for the capsule with previous 3-pin arm and new three bottom structures of the cone shape is performed using the one-channel flow test facilities. In order to estimate the compatibility with HANARO, the structural stability and integrity of the capsule, the out-pile test such as a loading/unloading test, a pressure drop test, a thermal performance test, a displacement measurement due to a vibration and an endurance test etc. is conducted, and the outer diameter of the bottom end cap ring to meet the HANARO requirements is selected. From out-pile test results the capsule with cone shape bottom structures is evaluated as to have the structural stability and the benefit from the fluid's flow respect. Also the size satisfied various requirements among three kinds of bottom end cap rings is 70mm in diameter. It is expected that the new bottom structures of the cone shape with 70mm in diameter will be applicable to all material and special capsules which will be designed and manufactured for the purpose of irradiation tests in the future.

Two types of fundamental luminescence of ionization-passive electrons and holes in optical dielectrics—Intraband-electron and interband-hole luminescence (theoretical calculation and comparison with experiment)

Science.gov (United States)

Vaisburd, D. I.; Kharitonova, S. V.

1997-11-01

A short high-power pulse of ionizing radiation creates a high concentration of nonequilibrium electrons and holes in a dielectric. They quickly lose their energy, generating a multiplicity of secondary quasiparticles: electron—hole pairs, excitons, plasmons, phonons of all types, and others. When the kinetic energy of an electron becomes less that some value EΔ≈(1.3-2)Eg it loses the ability to perform collisional ionization and electron excitations of the dielectric medium. Such an electron is said to be ionization-passive. It relaxes to the bottom of the lower conduction band by emitting phonons. Similarly a hole becomes ionization-passive when it “floats up” above some level EH and loses the ability for Auger ionization of the dielectric medium. It continues to float upward to the ceiling of the upper valance band only by emitting phonons. The concentrations of ionization-passive electrons and holes are larger by several orders of magnitude than those of the active electrons and holes and consequently make of a far larger contribution to many kinetic processes such as luminescence. Intraband and interband quantum transitions make the greatest contribution to the fundamental (independent of impurities and intrinsic defects) electromagnetic radiation of ionization-passive electrons and holes. Consequently the brightest types of purely fundamental luminescence of strongly nonequilibrium electrons and holes are intraband and interband luminescence. These forms of luminescence, discovered relatively recently, carry valuable information on the high-energy states of the electrons in the conduction band and of the holes in the valence band of a dielectric. Experimental investigations of these types of luminescence were made, mainly on alkali halide crystals which were excited by nanoseconal pulses of high-current-density electrons and by two-photon absorption of the ultraviolet harmonics of pulsed laser radiation beams of nanosecond and picosecond duration. The

Measurement of Air Flow Characteristics Using Seven-Hole Cone Probes

Science.gov (United States)

Takahashi, Timothy T.

1997-01-01

The motivation for this work has been the development of a wake survey system. A seven-hole probe can measure the distribution of static pressure, total pressure, and flow angularity in a wind tunnel environment. The author describes the development of a simple, very efficient algorithm to compute flow properties from probe tip pressures. Its accuracy and applicability to unsteady, turbulent flow are discussed.

The influence of triple bottom line on international operations management

Directory of Open Access Journals (Sweden)

Francisco Sperotto Flores

2017-12-01

Full Text Available This paper takes a triple bottom line perspective to analyze how the international operations literature integrates economic, social, and environmental issues. Additionally, it shows the main drivers of and barriers to the adoption of triple bottom line practices by companies in an international context. We conducted a literature review in English language journals which publish research of production and operations management and sustainability, resulting in a final sample of 29 papers. Results show that social and legal pressure for companies to adopt a responsible behavior prompts an isomorphic process that leads them to conduct their operations on behalf of triple bottom line goals. Behavioral differences between spin-offs in various countries caused institutions to create mechanisms that can press and change private standards through regulation and enforcement. There is room for progress in studies that seek to analyze the company’s relationships in its international experience and its multi-institutional relations.

Measurement of the magnetic field inside the holes of a drilled bulk high-Tc superconductor

Science.gov (United States)

Lousberg, Gregory P.; Fagnard, Jean-François; Noudem, Jacques G.; Ausloos, Marcel; Vanderheyden, Benoit; Vanderbemden, Philippe

2009-04-01

We use macroscopic holes drilled in a bulk YBCO superconductor to probe its magnetic properties in the volume of the sample. The sample is subjected to an AC magnetic flux with a density ranging from 30 to 130 mT and the flux in the superconductor is probed by miniature coils inserted in the holes. In a given hole, three different penetration regimes can be observed: (i) the shielded regime, where no magnetic flux threads the hole; (ii) the gradual penetration regime, where the waveform of the magnetic field has a clipped sine shape whose fundamental component scales with the applied field; and (iii) the flux concentration regime, where the waveform of the magnetic field is nearly a sine wave, with an amplitude exceeding that of the applied field by up to a factor of two. The distribution of the penetration regimes in the holes is compared with that of the magnetic flux density at the top and bottom surfaces of the sample, and is interpreted with the help of optical polarized light micrographs of these surfaces. We show that the measurement of the magnetic field inside the holes can be used as a local characterization of the bulk magnetic properties of the sample.

Operational design and pressure response of large-scale compressed air energy storage in porous formations

Science.gov (United States)

Wang, Bo; Bauer, Sebastian

2017-04-01

With the rapid growth of energy production from intermittent renewable sources like wind and solar power plants, large-scale energy storage options are required to compensate for fluctuating power generation on different time scales. Compressed air energy storage (CAES) in porous formations is seen as a promising option for balancing short-term diurnal fluctuations. CAES is a power-to-power energy storage, which converts electricity to mechanical energy, i.e. highly pressurized air, and stores it in the subsurface. This study aims at designing the storage setup and quantifying the pressure response of a large-scale CAES operation in a porous sandstone formation, thus assessing the feasibility of this storage option. For this, numerical modelling of a synthetic site and a synthetic operational cycle is applied. A hypothetic CAES scenario using a typical anticline structure in northern Germany was investigated. The top of the storage formation is at 700 m depth and the thickness is 20 m. The porosity and permeability were assumed to have a homogenous distribution with a value of 0.35 and 500 mD, respectively. According to the specifications of the Huntorf CAES power plant, a gas turbine producing 321 MW power with a minimum inlet pressure of 43 bars at an air mass flowrate of 417 kg/s was assumed. Pressure loss in the gas wells was accounted for using an analytical solution, which defines a minimum bottom hole pressure of 47 bars. Two daily extraction cycles of 6 hours each were set to the early morning and the late afternoon in order to bypass the massive solar energy production around noon. A two-year initial filling of the reservoir with air and ten years of daily cyclic operation were numerically simulated using the Eclipse E300 reservoir simulator. The simulation results show that using 12 wells the storage formation with a permeability of 500 mD can support the required 6-hour continuous power output of 321MW, which corresponds an energy output of 3852 MWh per

Strong deflection gravitational lensing by a modified Hayward black hole

Energy Technology Data Exchange (ETDEWEB)

Zhao, Shan-Shan; Xie, Yi [Nanjing University, School of Astronomy and Space Science, Nanjing (China); Nanjing University, Ministry of Education, Key Laboratory of Modern Astronomy and Astrophysics, Nanjing (China)

2017-05-15

A modified Hayward black hole is a nonsingular black hole. It is proposed that it would form when the pressure generated by quantum gravity can stop matter's collapse as the matter reaches the Planck density. Strong deflection gravitational lensing occurring nearby its event horizon might provide some clues of these quantum effects in its central core. We investigate observables of the strong deflection lensing, including angular separations, brightness differences and time delays between its relativistic images, and we estimate their values for the supermassive black hole in the Galactic center. We find that it is possible to distinguish the modified Hayward black hole from a Schwarzschild one, but it demands a very high resolution, beyond current stage. (orig.)

Large Eddy Simulations of a Bottom Boundary Layer Under a Shallow Geostrophic Front

Science.gov (United States)

Bateman, S. P.; Simeonov, J.; Calantoni, J.

2017-12-01

The unstratified surf zone and the stratified shelf waters are often separated by dynamic fronts that can strongly impact the character of the Ekman bottom boundary layer. Here, we use large eddy simulations to study the turbulent bottom boundary layer associated with a geostrophic current on a stratified shelf of uniform depth. The simulations are initialized with a spatially uniform vertical shear that is in geostrophic balance with a pressure gradient due to a linear horizontal temperature variation. Superposed on the temperature front is a stable vertical temperature gradient. As turbulence develops near the bottom, the turbulence-induced mixing gradually erodes the initial uniform temperature stratification and a well-mixed layer grows in height until the turbulence becomes fully developed. The simulations provide the spatial distribution of the turbulent dissipation and the Reynolds stresses in the fully developed boundary layer. We vary the initial linear stratification and investigate its effect on the height of the bottom boundary layer and the turbulence statistics. The results are compared to previous models and simulations of stratified bottom Ekman layers.

Sediment movement along the U.S. east coast continental shelf-I. Estimates of bottom stress using the Grant-Madsen model and near-bottom wave and current measurements

Science.gov (United States)

Lyne, V.D.; Butman, B.; Grant, W.D.

1990-01-01

Bottom stress is calculated for several long-term time-series observations, made on the U.S. east coast continental shelf during winter, using the wave-current interaction and moveable bed models of Grant and Madsen (1979, Journal of Geophysical Research, 84, 1797-1808; 1982, Journal of Geophysical Research, 87, 469-482). The wave and current measurements were obtained by means of a bottom tripod system which measured current using a Savonius rotor and vane and waves by means of a pressure sensor. The variables were burst sampled about 10% of the time. Wave energy was reasonably resolved, although aliased by wave groupiness, and wave period was accurate to 1-2 s during large storms. Errors in current speed and direction depend on the speed of the mean current relative to the wave current. In general, errors in bottom stress caused by uncertainties in measured current speed and wave characteristics were 10-20%. During storms, the bottom stress calculated using the Grant-Madsen models exceeded stress computed from conventional drag laws by a factor of about 1.5 on average and 3 or more during storm peaks. Thus, even in water as deep as 80 m, oscillatory near-bottom currents associated with surface gravity waves of period 12 s or longer will contribute substantially to bottom stress. Given that the Grant-Madsen model is correct, parameterizations of bottom stress that do not incorporate wave effects will substantially underestimate stress and sediment transport in this region of the continental shelf.

Tensile strength decreases and perfusion pressure of 3-holed polyamide epidural catheters increases in long-term epidural infusion.

Science.gov (United States)

Kim, Pascal; Meyer, Urs; Schüpfer, Guido; Rukwied, Roman; Konrad, Christoph; Gerber, Helmut

2011-01-01

Epidural analgesia is an established method for pain management. The failure rate is 8% to 12% due to technical difficulties (catheter dislocation and/or disconnection; partial or total catheter occlusion) and management. The mechanical properties of the catheters, like tensile strength and flow rate, may also be affected by the analgesic solution and/or the tissue environment. We investigated the tensile strength and perfusion pressure of new (n=20), perioperatively (n=30), and postoperatively (n=73) used epidural catheters (20-gauge, polyamide, closed tip, 3 side holes; Perifix [B. Braun]). To prevent dislocation, epidural catheters were taped (n=5) or fixed by suture (n=68) to the skin. After removal, mechanical properties were assessed by a tensile-testing machine (INSTRON 4500), and perfusion pressure was measured at flow rates of 10, 20, and 40 mL/h. All catheters demonstrated a 2-step force transmission. Initially, a minimal increase of length could be observed at 15 N followed by an elongation of several cm at additional forces (7 N). Breakage occurred in the control group at 23.5±1.5 N compared with 22.4±1.6 N in perioperative and 22.4±1.7 N in postoperative catheters (Ptensile strength, whereas perfusion pressure at clinically used flow rates (10 mL/h) increased significantly from 19±1.3 to 44±72 mm Hg during long-term (≥7 days) epidural analgesia (Ptensile strength or perfusion pressure. Epidural catheter use significantly increases the perfusion pressure and decreases the tensile strength. Copyright © 2011 by American Society of Regional Anesthesia and Pain Medicine

Black holes can have curly hair

International Nuclear Information System (INIS)

Bronnikov, K. A.; Zaslavskii, O. B.

2008-01-01

We study equilibrium conditions between a static, spherically symmetric black hole and classical matter in terms of the radial pressure to density ratio p r /ρ=w(u), where u is the radial coordinate. It is shown that such an equilibrium is possible in two cases: (i) the well-known case w→-1 as u→u h (the horizon), i.e., 'vacuum' matter, for which ρ(u h ) can be nonzero; (ii) w→-1/(1+2k) and ρ∼(u-u h ) k as u→u h , where k>0 is a positive integer (w=-1/3 in the generic case k=1). A noninteracting mixture of these two kinds of matter can also exist. The whole reasoning is local, hence the results do not depend on any global or asymptotic conditions. They mean, in particular, that a static black hole cannot live inside a star with nonnegative pressure and density. As an example, an exact solution for an isotropic fluid with w=-1/3 (that is, a fluid of disordered cosmic strings), with or without vacuum matter, is presented.

Mass-induced sea level variations in the Red Sea from GRACE, steric-corrected altimetry, in situ bottom pressure records, and hydrographic observations

Science.gov (United States)

Feng, W.; Lemoine, J.-M.; Zhong, M.; Hsu, H. T.

2014-08-01

An annual amplitude of ∼18 cm mass-induced sea level variations (SLV) in the Red Sea is detected from the Gravity Recovery and Climate Experiment (GRACE) satellites and steric-corrected altimetry from 2003 to 2011. The annual mass variations in the region dominate the mean SLV, and generally reach maximum in late January/early February. The annual steric component of the mean SLV is relatively small (mass-induced SLV. In situ bottom pressure records at the eastern coast of the Red Sea validate the high mass variability observed by steric-corrected altimetry and GRACE. In addition, the horizontal water mass flux of the Red Sea estimated from GRACE and steric-corrected altimetry is validated by hydrographic observations.

Coronal holes and high-speed wind streams

International Nuclear Information System (INIS)

Zirker, J.B.

1977-01-01

Coronal holes low have been identified as Bartel's M regions, i.e., sources of high-speed wind streams that produce recurrent geomagnetic variations. Throughout the Skylab period the polar caps of the Sun were coronal holes, and at lower latitudes the most persistent and recurrent holes were equatorial extensions of the polar caps. The holes rotated 'rigidly' at the equatorial synodic rate. They formed in regions of unipolar photospheric magnetic field, and their internal magnetic fields diverged rapidly with increasing distance from the sun. The geometry of the magnetic field in the inner corona seems to control both the physical properties of the holes and the global distribution of high-speed wind streams in the heliosphere. The latitude variation of the divergence of the coronal magnetic field lines produces corresponding variations in wind speed.During the years of declining solar activity the global field of the corona approximates a perturbed dipole. The divergence of field lines in each hemisphere produces a high-speed wind near the poles and low-speed wind in a narrow belt that coincides with the magnetic neutral sheet. The analysis of electron density measurements within a polar hole indicates that solar wind is accelerated principally in the region between 2 and 5 R/sub s/ and that mechanical wave pressure (possibly Alfven wave) may be responsible for the accleration of the wind. Phenomenological models for the birth and decay of coronal holes have been proposed. Attempts to explain the birth and rigid rotation of holes through dynamo action have been only partially successful. The 11-year variation of cosmic ray intensities at the earth may result from cyclic variation of open field regions associated with coronal holes

VL1 Digs A Deep Hole On Mars

Science.gov (United States)

1977-01-01

VIKING LANDER DIGS A DEEP HOLE ON MARS -- This six-inch-deep, 12- inch-wide, 29-inch-long hole was dug Feb. 12 and 14 by Viking Lander 1 as the first sequence in an attempt to reach a foot beneath the surface of the red planet. The activity is in the same area where Lander 1 acquired its first soil samples last July. The trench was dug by repeatedly backhoeing in a left-right-center pattern. The backhoe teeth produced the small parallel ridges at the far end of the trench (upper left). The larger ridges running the length of the trench are material left behind during the backhoe operation. What appears to be small rocks along the ridges and in the soil at the near end of the trench are really small dirt clods. The clods and the steepness of the trench walls indicate the material is cohesive and behaves something like ordinary flour. After a later sequence, to be performed March 1 and 2, a soil sample will be taken from the bottom of the trench for inorganic soil analysis and later for biology analysis. Information about the soil taken from the bottom of the trench may help explain the weathering process on Mars and may help resolve the dilemma created by Viking findings that first suggest but then cast doubt on the possibility of life in the Martian soil. The trench shown here is a result of one of the most complex command sequences yet performed by the lander. Viking l has been operating at Chryse Planitia on Mars since it landed July 20, 1976.

Effects of pressure on doped Kondo insulators

International Nuclear Information System (INIS)

Lee, Chengchung; Xu, Wang

1999-08-01

The effects of pressure on the doped Kondo insulators (KI) are studied in the framework of the slave-boson mean-field theory under the coherent potential approximation (CPA). A unified picture for both electron-type KI and hole-type KI is presented. The density of states of the f-electrons under the applied pressures and its variation with the concentration of the Kondo holes are calculated self-consistently. The specific heat coefficient, the zero-temperature magnetic susceptibility as well as the low temperature electric resistivity of the doped KI under various pressures are obtained. The two contrasting pressure-dependent effects observed in the doped KI systems can be naturally explained within a microscopic model. (author)

A Study on the Influence of Fuel Pipe on Fuel Injection Characteristics of Each Nozzle Hole in Diesel Injector

Directory of Open Access Journals (Sweden)

Luo Fuqiang

2016-01-01

Full Text Available The inner diameter of high pressure fuel pipe has a significant effect on the fuel injection process and the performance of a diesel engine. The spray impact force of each nozzle hole of a conventional injection system of pump-line-nozzle for diesel engine (based on the spray momentum flux and the injection pressure (on a fuel injection pump test rig were measured. With varying fuel injection quantities and pump speed, the effects of the inner diameter of the high pressure fuel pipe on fuel injection process and the fuel injection characteristics of each nozzle hole were analyzed. It was noted from experimental results that the fuel injection pressure changes with variations in the inner diameter of the high pressure fuel pipe and also the injection duration gradually increases with increase in the inner diameter. At low injection pump speed, even with the same geometric fuel deliver rate, the injection duration also increases gradually. Due to throttling effect and reduction in injection pressure, the fuel injection quantities of the injection nozzle were relatively minimal when the inner diameters of the high pressure fuel pipe were respectively small and large. The optimum injection pipe inner diameter for the right quantity for fuel injection falls between the two cases (between small and large. In addition, the injection rate of each nozzle hole increases with the decrease in angle between the needle axis and each of the nozzle hole axis. The fuel injection quantity of each nozzle hole increases while their relative difference decreases with increasing pump speed.

Band-to-band tunneling distance analysis in the heterogate electron–hole bilayer tunnel field-effect transistor

Energy Technology Data Exchange (ETDEWEB)

Padilla, J. L., E-mail: jose.padilladelatorre@epfl.ch [Nanoelectronic Devices Laboratory, École Polytechnique Fédérale de Lausanne, Lausanne CH-1015 (Switzerland); Departamento de Electrónica y Tecnología de los Computadores, Universidad de Granada, Avda. Fuentenueva s/n, 18071 Granada (Spain); Palomares, A. [Departamento de Matemática Aplicada, Universidad de Granada, Avda. Fuentenueva s/n, 18071 Granada (Spain); Alper, C.; Ionescu, A. M. [Nanoelectronic Devices Laboratory, École Polytechnique Fédérale de Lausanne, Lausanne CH-1015 (Switzerland); Gámiz, F. [Departamento de Electrónica y Tecnología de los Computadores, Universidad de Granada, Avda. Fuentenueva s/n, 18071 Granada (Spain)

2016-01-28

In this work, we analyze the behavior of the band-to-band tunneling distance between electron and hole subbands resulting from field-induced quantum confinement in the heterogate electron–hole bilayer tunnel field-effect transistor. We show that, analogously to the explicit formula for the tunneling distance that can be easily obtained in the semiclassical framework where the conduction and valence band edges are allowed states, an equivalent analytical expression can be derived in the presence of field-induced quantum confinement for describing the dependence of the tunneling distance on the body thickness and material properties of the channel. This explicit expression accounting for quantum confinement holds valid provided that the potential wells for electrons and holes at the top and bottom of the channel can be approximated by triangular profiles. Analytical predictions are compared to simulation results showing very accurate agreement.

Thermal stress measurement in continuous welded rails using the hole-drilling method

Science.gov (United States)

Zhu, Xuan; Lanza di Scalea, Francesco; Fateh, Mahmood

2016-04-01

The absence of expansion joints in Continuous Welded Rail (CWR) has created the need for the railroad industry to determine the in-situ level of thermal stresses so as to prevent train accidents caused by rail buckling in hot weather and by rail breakage in cold weather. The development of non-destructive or semi-destructive methods for determining the level of thermal stresses in rails is today a high research priority. This study explores the known hole-drilling method as a possible solution to this problem. A new set of calibration coefficients to compute the relieved stress field with the finer hole depth increments was determined by a 3D Finite Element Analysis that modeled the entire hole geometry, including the mechanics of the hole bottom and walls. To compensate the residual stress components, a linear relationship was experimentally established between the longitudinal and the vertical residual stresses of two common sizes of rails, the 136RE and the 141RE, with statistical significance. This result was then utilized to isolate the longitudinal thermal stress component in hole-drilling tests conducted on the 136RE and 141RE thermally-loaded rails at the Large-scale CWR Test-bed of UCSD's Powell Research Laboratories. The results from the Test-bed showed that the hole-drilling procedure, with the appropriate residual stress compensation, can indeed estimate the in-situ thermal stresses to achieve a +/-5°F accuracy of Neutral Temperature determination with a 90% statistical confidence, which is the desired industry gold standard.

New perspective for black hole thermodynamics in Gauss-Bonnet-Born-Infeld massive gravity

International Nuclear Information System (INIS)

Hendi, Seyed Hossein; Li, Gu-Qiang; Mo, Jie-Xiong; Panahiyan, Shahram; Panah, Behzad Eslam

2016-01-01

Following an earlier study regarding Einstein-Gauss-Bonnet-massive black holes in the presence of a Born-Infeld nonlinear electromagnetic field (Hendi, arXiv:1510.00108, 2016), we study thermodynamical structure and critical behavior of these black holes through various methods in this paper. Geometrical thermodynamics is employed to give a picture regarding the phase transition of these black holes. Next, a new method is used to derive critical pressure and radius of the horizon of these black holes. In addition, Maxwell equal area law is employed to study the Van der Waals like behavior of these black holes. Moreover, the critical exponents are calculated and by using Ehrenfest equations, the type of phase transition is determined. (orig.)

New perspective for black hole thermodynamics in Gauss-Bonnet-Born-Infeld massive gravity

Energy Technology Data Exchange (ETDEWEB)

Hendi, Seyed Hossein [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of); Research Institute for Astronomy and Astrophysics of Maragha (RIAAM),Maragha (Iran, Islamic Republic of); Li, Gu-Qiang; Mo, Jie-Xiong [Lingnan Normal University, Institute of Theoretical Physics, Zhanjiang, Guangdong (China); Panahiyan, Shahram [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of); Shahid Beheshti University, Physics Department, Tehran (Iran, Islamic Republic of); Panah, Behzad Eslam [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of)

2016-10-15

Following an earlier study regarding Einstein-Gauss-Bonnet-massive black holes in the presence of a Born-Infeld nonlinear electromagnetic field (Hendi, arXiv:1510.00108, 2016), we study thermodynamical structure and critical behavior of these black holes through various methods in this paper. Geometrical thermodynamics is employed to give a picture regarding the phase transition of these black holes. Next, a new method is used to derive critical pressure and radius of the horizon of these black holes. In addition, Maxwell equal area law is employed to study the Van der Waals like behavior of these black holes. Moreover, the critical exponents are calculated and by using Ehrenfest equations, the type of phase transition is determined. (orig.)

Liquid oil production from shale gas condensate reservoirs

Science.gov (United States)

Sheng, James J.

2018-04-03

A process of producing liquid oil from shale gas condensate reservoirs and, more particularly, to increase liquid oil production by huff-n-puff in shale gas condensate reservoirs. The process includes performing a huff-n-puff gas injection mode and flowing the bottom-hole pressure lower than the dew point pressure.

Collisions Around a Black Hole Mean Mealtime

Science.gov (United States)

Kohler, Susanna

2017-08-01

When a normally dormant supermassive black hole burps out a brief flare, its assumed that a star was torn apart and fell into the black hole. But a new study suggests that some of these flares might have a slightly different cause.Not a Disruption?Artists impression of a tidal disruption event, in which a star has been pulled apart and its gas feeds the supermassive black hole. [NASA/JPL-Caltech]When a star swings a little too close by a supermassive black hole, the black holes gravity can pull the star apart, completely disrupting it. The resulting gas can then accrete onto the black hole, feeding it and causing it to flare. The predicted frequency of these tidal disruption events and their expected light curves dont perfectly match all our observations of flaring black holes, however.This discrepancy has led two scientists from the Columbia Astrophysics Laboratory, Brian Metzger and Nicholas Stone, to wonder if we can explain flares from supermassive black holes in another way. Could a differentevent masquerade as a tidal disruption?Evolution of a stars semimajor axis (top panel) and radius (bottom panel) as a function of time since Roche-lobe overflow began onto a million-solar-mass black hole. Curves show stars of different masses. [Metzger Stone 2017]Inspirals and OutspiralsIn the dense nuclear star cluster surrounding a supermassive black hole, various interactions can send stars on new paths that take them close to the black hole. In many of these interactions, the stars will end up on plunging orbits, often resulting in tidal disruption. But sometimes stars can approach the black hole on tightly bound orbits with lower eccentricities.A main-sequence star on such a path, in what is known as an extreme mass ratio inspiral (EMRI), slowly approaches the black hole over a period of millions of years, eventually overflowing its Roche lobe and losing mass. Theradius of the star inflates, driving more mass loss and halting the stars inward progress. The star then

An Analysis of Hole Trapping at Grain Boundary or Poly-Si Floating-Body MOSFET.

Science.gov (United States)

Jang, Taejin; Baek, Myung-Hyun; Kim, Hyungjin; Park, Byung-Gook

2018-09-01

In this paper, we demonstrate the characteristics of the floating body effect of poly-silicon with grain boundary by SENTAURUS™ TCAD simulation. As drain voltage increases, impact ionization occurs at the drain-channel junction. And these holes created by impact ionization are deposited on the bottom of the body to change the threshold voltage. This feature, the kink effect, is also observed in fully depleted silicon on insulator because grain boundary of the poly-silicon serve as a storage to trap the holes. We simulate the transfer curve depending on the density and position of the grain boundary. The trap density of the grain boundary affects the device characteristics significantly. However similar properties appear except where the grain boundary is located on the drain side.

THE EFFECT OF WELL-BORE REVERSE FLOW OF FLUID ON ...

African Journals Online (AJOL)

ES Obe

1980-03-01

Mar 1, 1980 ... ABSTRACT. Well-bore storage may dominate the bottom-hole pressure profile of ... Type- curve matching is however only accurate when the storage factor .... numerical integration technique ... existence of a measure of well-.

Black holes

International Nuclear Information System (INIS)

Feast, M.W.

1981-01-01

This article deals with two questions, namely whether it is possible for black holes to exist, and if the answer is yes, whether we have found any yet. In deciding whether black holes can exist or not the central role in the shaping of our universe played by the forse of gravity is discussed, and in deciding whether we are likely to find black holes in the universe the author looks at the way stars evolve, as well as white dwarfs and neutron stars. He also discusses the problem how to detect a black hole, possible black holes, a southern black hole, massive black holes, as well as why black holes are studied

Optimization long hole blast fragmentation techniques and detonating circuit underground uranium mine stope

International Nuclear Information System (INIS)

Li Qin; Yang Lizhi; Song Lixia; Qin De'en; Xue Yongshe; Wang Zhipeng

2012-01-01

Aim at high rate of large blast fragmentation, a big difficulty in long hole drilling and blasting underground uranium mine stope, it is pointed out at the same time of taking integrated technical management measures, the key is to optimize the drilling and blasting parameters and insure safety the act of one that primes, adopt 'minimum burden' blasting technique, renew the stope fragmentation process, and use new process of hole bottom indirect initiation fragmentation; optimize the detonating circuit and use safe, reliable and economically rational duplex non-electric detonating circuit. The production practice shows that under the guarantee of strictly controlled construction quality, the application of optimized blast fragmentation technique has enhanced the reliability of safety detonation and preferably solved the problem of high rate of large blast fragments. (authors)

Geology of the UE12t No. 3 vertical drill hole, area 12, Nevada Test Site

International Nuclear Information System (INIS)

Terry, S.S.

1975-11-01

The UE12t No. 3 vertical drill hole, located near the north end of Rainier Mesa, was drilled to a total depth of 663 m (2,176 ft). The UE12t No. 3 vertical hole was drilled to further evaluate the subsurface stratigraphy northwest of the t-tunnel complex area in preparation for mining of the U12t.03 (Husky Pup) drift. The drill hole is collared in the Rainier Mesa Member of the Timber Mountain Tuff and penetrates down the stratigraphic section through the Paintbrush Tuff, the welded Grouse Canyon Member of the Belted Range Tuff, tunnel beds 5-3, the Tub Spring Member of the Belted Range Tuff, tunnel bed 2, Crater Flat Tuff, tunnel bed 1, Redrock Valley Tuff, and bottoms in older Tertiary tuffaceous and Paleozoic quartzite rubble having a partially argillized, tuffaceous, soillike matrix. The tuff of Dead Horse Flat and the bedded and ash-flow tuffs of Area 20 were not differentiated in the logging of this drill hole. Stratigraphy, structure, engineering geology, and physical properties and their relation to tunneling are discussed

Characterization of the Airflow from a Bottom Hung Window under Natural Ventilation

DEFF Research Database (Denmark)

Svidt, Kjeld; Heiselberg, Per; Nielsen, Peter V.

This paper describes the results of laboratory measurements of the airflow from a bottom hung window mounted near the ceiling of a ventilated room. In the laboratory set-up it was possible to control the temperature difference and the airflow rate through the window. The pressure drop through...

Cyclic and heteroclinic flows near general static spherically symmetric black holes

Energy Technology Data Exchange (ETDEWEB)

Ahmed, Ayyesha K.; Jamil, Mubasher [National University of Sciences and Technology(NUST), Department of Mathematics, School of Natural Sciences (SNS), Islamabad (Pakistan); Azreg-Ainou, Mustapha [Baskent University, Engineering Faculty, Ankara (Turkey); Faizal, Mir [University of Lethbridge, Department of Physics and Astronomy, Alberta (Canada); University of Waterloo, Department of Physics and Astronomy, Waterloo, ON (Canada)

2016-05-15

We investigate the Michel-type accretion onto a static spherically symmetric black hole. Using a Hamiltonian dynamical approach, we show that the standard method employed for tackling the accretion problem has masked some properties of the fluid flow. We determine new analytical solutions that are neither transonic nor supersonic as the fluid approaches the horizon(s); rather, they remain subsonic for all values of the radial coordinate. Moreover, the three-velocity vanishes and the pressure diverges on the horizon(s), resulting in a flow-out of the fluid under the effect of its own pressure. This is in favor of the earlier prediction that pressure-dominant regions form near the horizon. This result does not depend on the form of the metric and it applies to a neighborhood of any horizon where the time coordinate is timelike. For anti-de Sitter-like f(R) black holes we discuss the stability of the critical flow and determine separatrix heteroclinic orbits. For de Sitter-like f(R) black holes, we construct polytropic cyclic, non-homoclinic, physical flows connecting the two horizons. These flows become non-relativistic for Hamiltonian values higher than the critical value, allowing for a good estimate of the proper period of the flow. (orig.)

Hydrostatic Pressure Sensing with High Birefringence Photonic Crystal Fibers

Science.gov (United States)

Fávero, Fernando C.; Quintero, Sully M. M.; Martelli, Cicero; Braga, Arthur M.B.; Silva, Vinícius V.; Carvalho, Isabel C. S.; Llerena, Roberth W. A.; Valente, Luiz C. G.

2010-01-01

The effect of hydrostatic pressure on the waveguiding properties of high birefringence photonic crystal fibers (HiBi PCF) is evaluated both numerically and experimentally. A fiber design presenting form birefringence induced by two enlarged holes in the innermost ring defining the fiber core is investigated. Numerical results show that modal sensitivity to the applied pressure depends on the diameters of the holes, and can be tailored by independently varying the sizes of the large or small holes. Numerical and experimental results are compared showing excellent agreement. A hydrostatic pressure sensor is proposed and demonstrated using an in-fiber modal interferometer where the two orthogonally polarized modes of a HiBi PCF generate fringes over the optical spectrum of a broad band source. From the analysis of experimental results, it is concluded that, in principle, an operating limit of 92 MPa in pressure could be achieved with 0.0003% of full scale resolution. PMID:22163435

Experimental Study on Peak Pressure of Shock Waves in Quasi-Shallow Water

Directory of Open Access Journals (Sweden)

Zhenxiong Wang

2015-01-01

Full Text Available Based on the similarity laws of the explosion, this research develops similarity requirements of the small-scale experiments of underwater explosions and establishes a regression model for peak pressure of underwater shock waves under experimental condition. Small-scale experiments are carried out with two types of media at the bottom of the water and for different water depths. The peak pressure of underwater shock waves at different measuring points is acquired. A formula consistent with the similarity law of explosions is obtained and an analysis of the regression precision of the formula confirms its accuracy. Significance experiment indicates that the influence of distance between measuring points and charge on peak pressure of underwater shock wave is the greatest and that of water depth is the least within the range of geometric parameters. An analysis of data from experiments with different media at the bottom of the water reveals an influence on the peak pressure, as the peak pressure of a shock wave in a body of water with a bottom soft mud and rocks is about 1.33 times that of the case where the bottom material is only soft mud.

Pressure vessel lid

International Nuclear Information System (INIS)

Schoening, J.; Elter, C.; Becker, G.; Pertiller, S.

1986-01-01

The invention concerns a lid for closing openings in reactor pressure vessels containing helium, which is made as a circular casting with hollow spaces and a flat floor and is set on the opening and kept down. It consists of helium-tight metal cast material with sufficient temperature resistance. There are at least two concentric heat resistant seals let into the bottom of the lid. The bottom is in immediate contact with the container atmosphere and has hollow spaces in its inside in the area opposite to the opening. (orig./HP) [de

Development of a Device for a Material Irradiation Test in the OR Test Hole

Energy Technology Data Exchange (ETDEWEB)

Cho, Man Soon; Kang, Y. H.; Kim, B. G.; Choo, K. N.; Sohn, J. M.; Shin, Y. T.; Park, S. J.; Seo, C. K

2008-05-15

To develop a technology and a device for the irradiation test for utilization of the OR/IP holes according to the various requirements of users, the properties of the OR/IP holes were investigated and an irradiation device for the OR hole was designed and fabricated. The OR-4, 5 and the IP-9, 10, 11 holes were selected as those suitable to irradiation tests among the test holes located in the out core area. The conceptual design was performed to design a device to irradiate materials using the OR and IP holes. The capsule for the OR holes is fixed by pressing the protection tube using a clamping device, on the other hand the IP capsule is inserted in the hole without a special clamping device. In the basic design of the irradiation device for the OR hole, the capsules having the outside diameter of 50, 52, 54, 56mm were reviewed theoretically to investigate if they meet the hydraulic and vibration conditions required in the HANARO. The results of the pressure drop test showed that the 3 kinds of capsules having diameter of 52, 54, 56mm satisfied the requirement for the pressure difference and flow rate in HANARO. The capsule of {phi}56mm out of the above three satisfied the vibration condition and was finally selected giving consideration of a capacity of specimens. The capsule having a diameter of {phi}56mm was fabricated and the flow rate was measured. Using the velocity data measured at the out-core facility, the heat transfer coefficient, and the temperature on the surface of the capsule was evaluated to confirm it less than the ONB temperature. As a result, the capsule of {phi}56mm was selected for the irradiation test at the OR holes.

σ-holes and π-holes: Similarities and differences.

Science.gov (United States)

Politzer, Peter; Murray, Jane S

2018-04-05

σ-Holes and π-holes are regions of molecules with electronic densities lower than their surroundings. There are often positive electrostatic potentials associated with them. Through these potentials, the molecule can interact attractively with negative sites, such as lone pairs, π electrons, and anions. Such noncovalent interactions, "σ-hole bonding" and "π-hole bonding," are increasingly recognized as being important in a number of different areas. In this article, we discuss and compare the natures and characteristics of σ-holes and π-holes, and factors that influence the strengths and locations of the resulting electrostatic potentials. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Charged dilatonic black holes in gravity's rainbow

Energy Technology Data Exchange (ETDEWEB)

Hendi, S.H. [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of); Research Institute for Astronomy and Astrophysics of Maragha (RIAAM), Maragha (Iran, Islamic Republic of); Faizal, Mir [University of Waterloo, Department of Physics and Astronomy, Waterloo, ON (Canada); Panah, B.E. [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of); Panahiyan, S. [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of); Shahid Beheshti University, Physics Department, Tehran (Iran, Islamic Republic of)

2016-05-15

In this paper, we present charged dilatonic black holes in gravity's rainbow. We study the geometric and thermodynamic properties of black hole solutions. We also investigate the effects of rainbow functions on different thermodynamic quantities for these charged black holes in dilatonic gravity's rainbow. Then we demonstrate that the first law of thermodynamics is valid for these solutions. After that, we investigate thermal stability of the solutions using the canonical ensemble and analyze the effects of different rainbow functions on the thermal stability. In addition, we present some arguments regarding the bound and phase transition points in context of geometrical thermodynamics. We also study the phase transition in extended phase space in which the cosmological constant is treated as the thermodynamic pressure. Finally, we use another approach to calculate and demonstrate that the obtained critical points in extended phase space represent a second order phase transition for these black holes. (orig.)

Gravastars and black holes of anisotropic dark energy

International Nuclear Information System (INIS)

Chan, Roberto; Silva, Maria de Fatima Alves da; Rocha, Pedro Senna

2011-01-01

Full text: Dynamical models of prototype gravastars made of anisotropic dark energy are constructed, in which an infinitely thin spherical shell of a perfect fluid with the equation of state p = (1 - γ)σ divides the whole spacetime into two regions, the internal region filled with a dark energy fluid, and the external Schwarzschild region. The models represent 'bounded excursion' stable gravastars, where the thin shell is oscillating between two finite radii, while in other cases they collapse until the formation of black holes. Here we show, for the first time in the literature, a model of gravastar and formation of black hole with both interior and thin shell constituted exclusively of dark energy. Besides, the sign of the parameter of anisotropy (Pt - Pr ) seems to be relevant to the gravastar formation. The formation is favored when the tangential pressure is greater than the radial pressure, at least in the neighborhood of the isotropic case (ω = -1). (author)

Gravastars and black holes of anisotropic dark energy

Energy Technology Data Exchange (ETDEWEB)

Chan, Roberto [Observatorio Nacional (ON), Rio de Janeiro, RJ (Brazil); Silva, Maria de Fatima Alves da; Rocha, Pedro Senna [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil)

2011-07-01

Full text: Dynamical models of prototype gravastars made of anisotropic dark energy are constructed, in which an infinitely thin spherical shell of a perfect fluid with the equation of state p = (1 - {gamma}){sigma} divides the whole spacetime into two regions, the internal region filled with a dark energy fluid, and the external Schwarzschild region. The models represent 'bounded excursion' stable gravastars, where the thin shell is oscillating between two finite radii, while in other cases they collapse until the formation of black holes. Here we show, for the first time in the literature, a model of gravastar and formation of black hole with both interior and thin shell constituted exclusively of dark energy. Besides, the sign of the parameter of anisotropy (Pt - Pr ) seems to be relevant to the gravastar formation. The formation is favored when the tangential pressure is greater than the radial pressure, at least in the neighborhood of the isotropic case ({omega} = -1). (author)

Quantum vacuum energy near a black hole: the Maxwell field

International Nuclear Information System (INIS)

Elster, T.

1984-01-01

A quantised Maxwell field is considered propagating in the gravitational field of a Schwarzschild black hole. The vector Hartle-Hawking propagator is defined on the Riemannian section of the analytically continued space-time and expanded in terms of four-dimensional vector spherical harmonics. The equations for the radial functions appearing in the expansion are derived for both odd and even parity. Using the expansion of the vector Hartle-Hawking propagator, the point-separated expectation value of the Maxwellian energy-momentum tensor in the Hartle-Hawking vacuum is derived. The renormalised values of radial pressure, tangential pressure and energy density are obtained near the horizon of the black hole. In contrast to the scalar field, the Maxwell field exhibits a positive energy density near the horizon in the Hartle-Hawking vacuum state. (author)

Hydrostatic pressure mimics gravitational pressure in characean cells

Science.gov (United States)

Staves, M. P.; Wayne, R.; Leopold, A. C.

1992-01-01

Hydrostatic pressure applied to one end of a horizontal Chara cell induces a polarity of cytoplasmic streaming, thus mimicking the effect of gravity. A positive hydrostatic pressure induces a more rapid streaming away from the applied pressure and a slower streaming toward the applied pressure. In contrast, a negative pressure induces a more rapid streaming toward and a slower streaming away from the applied pressure. Both the hydrostatic pressure-induced and gravity-induced polarity of cytoplasmic streaming respond identically to cell ligation, UV microbeam irradiation, external Ca2+ concentrations, osmotic pressure, neutral red, TEA Cl-, and the Ca2+ channel blockers nifedipine and LaCl3. In addition, hydrostatic pressure applied to the bottom of a vertically-oriented cell can abolish and even reverse the gravity-induced polarity of cytoplasmic streaming. These data indicate that both gravity and hydrostatic pressure act at the same point of the signal transduction chain leading to the induction of a polarity of cytoplasmic streaming and support the hypothesis that characean cells respond to gravity by sensing a gravity-induced pressure differential between the cell ends.

Super-Eddington Mechanical Power of an Accreting Black Hole in M83

Science.gov (United States)

Soria, R.; Long, K. S.; Blair, W. P.; Godfrey, L.; Kuntz, K. D.; Lenc, E.; Stockdale, C.; Winkler, P. F.

2014-01-01

Mass accretion onto black holes releases energy in the form of radiation and outflows. Although the radiative flux cannot substantially exceed the Eddington limit, at which the outgoing radiation pressure impedes the inflow of matter, it remains unclear whether the kinetic energy flux is bounded by this same limit. Here, we present the detection of a radio-optical structure, powered by outflows from a non-nuclear black hole. Its accretion disk properties indicate that this black hole is less than 100 solar masses. The optical-infrared line emission implies an average kinetic power of 3 × 10(exp 40) erg second(exp -1), higher than the Eddington luminosity of the black hole. These results demonstrate kinetic power exceeding the Eddington limit over a sustained period, which implies greater ability to influence the evolution of the black hole's environment.

Black hole formation in perfect fluid collapse

International Nuclear Information System (INIS)

Goswami, Rituparno; Joshi, Pankaj S

2004-01-01

We construct here a special class of perfect fluid collapse models which generalizes the homogeneous dust collapse solution in order to include nonzero pressures and inhomogeneities into evolution. It is shown that a black hole is necessarily generated as the end product of continued gravitational collapse, rather than a naked singularity. We examine the nature of the central singularity forming as a result of endless collapse and it is shown that no nonspacelike trajectories can escape from the central singularity. Our results provide some insights into how the dynamical collapse works and into the possible formulations of the cosmic censorship hypothesis, which is as yet a major unsolved problem in black hole physics

pressure distribution in a layered reservoir with gas-cap and bottom

African Journals Online (AJOL)

2012-07-02

Jul 2, 2012 ... Finally, only fluid ratios is recommended as adequate to reveal which ... pressure derivatives, interlayer cross flow, heterogeneity, reservoir characterization, pressure ... sure derivatives to thoroughly understand movement.

Cylinder-type bottom reflector

International Nuclear Information System (INIS)

Elter, C.; Fritz, R.; Kissel, K.F.; Schoening, J.

1982-01-01

Proposal of a bottom reflector for gas-cooled nuclear reactor plants with a pebble bed of spherical fuel elements, where the horizontal forces acting from the core and the bottom reflector upon the side reflector are equally distributed. This is attained by the upper edge of the bottom reflector being placed levelly and by the angle of inclination of the recesses varying. (orig.) [de

Numerical simulation of water flow through the bottom en piece of a nuclear fuel assembly

International Nuclear Information System (INIS)

Navarro, Moyses A.; Santos, Andre A. Campagnole dos

2007-01-01

The water flow through the bottom nozzle of a nuclear fuel assembly was simulated using a commercial CFD code, CFX 10.0. Previously, simulations with a perforated plate similar to the bottom nozzle plate were performed to define the appropriate mesh refinement and turbulence model (κ-ε or SST). Subsequently, the numerical simulation was performed with the optimized mesh using the turbulence model (κ-ε in a standard bottom nozzle with some geometric simplifications. The numerical results were compared with experimental results to determine the pressure drop through the bottom nozzle in the Reynolds range from ∼10500 to ∼95000. The agreement between the numerical simulations and experimental results may be considered satisfactory. The study indicated that the CFD codes can play an important role in the development of pieces with complex geometries, optimizing the planning of the experiments and aiding in the experimental analysis. (author)

Effects of thermal fluctuations on the thermodynamics of modified Hayward black hole

Energy Technology Data Exchange (ETDEWEB)

Pourhassan, Behnam [Damghan University, School of Physics, Damghan (Iran, Islamic Republic of); Faizal, Mir [University of Lethbridge, Department of Physics and Astronomy, Lethbridge, AB (Canada); Debnath, Ujjal [Indian Institute of Engineering Science and Technology, Shibpur, Department of Mathematics, Howrah (India)

2016-03-15

In this work, we analyze the effects of thermal fluctuations on the thermodynamics of a modified Hayward black hole. These thermal fluctuations will produce correction terms for various thermodynamical quantities like entropy, pressure, internal energy, and specific heats. We also investigate the effect of these correction terms on the first law of thermodynamics. Finally, we study the phase transition for the modified Hayward black hole. It is demonstrated that the modified Hayward black hole is stable even after the thermal fluctuations are taken into account, as long as the event horizon is larger than a certain critical value. (orig.)

Hierarchical top-porous/bottom-tubular TiO 2 nanostructures decorated with Pd nanoparticles for efficient photoelectrocatalytic decomposition of synergistic pollutants

KAUST Repository

Zhang, Zhonghai

2012-02-22

In this paper, top-porous and bottom-tubular TiO 2 nanotubes (TiO 2 NTs) loaded with palladium nanoparticles (Pd/TiO 2 NTs) were fabricated as an electrode for an enhanced photoelectrocatalytic (PEC) activity toward organic dye decomposition. TiO 2 NTs with a unique hierarchical top-porous and bottom-tubular structure were prepared by a facile two-step anodization method and Pd nanoparticles were decorated onto the TiO 2 NTs via a photoreduction process. The PEC activity of Pd/TiO 2 NTs was investigated by decomposition of methylene blue (MB) and Rhodamine B (RhB). Because of formation Schottky junctions between TiO 2 and Pd, which significantly promoted the electron transfer and reduced the recombination of photogenerated electrons and holes, the Pd/TiO 2 NT electrode showed significantly higher PEC activities than TiO 2 NTs. Interestingly, an obvious synergy between two dyes was observed and corresponding mechanism based on facilitated transfer of electrons and holes as a result of a suitable energy level alignment was suggested. The findings of this work provide a fundamental insight not only into the fabrication but also utility of Schottky junctions for enhanced environmental remediation processes. © 2012 American Chemical Society.

The Effect of the Holes Size Change of Lower-Support-Structure-Bottom Plate on the Reactor Core-Inlet Flow-Distribution

International Nuclear Information System (INIS)

Lee, Gong Hee; Bang, Young Seok; Cheong, Ae Ju

2015-01-01

Complex thermal-hydraulic phenomena exist inside PWR because reactor interiors include a fuel assembly, control rod assembly, ICI (In-Core Instrumentation), and other internal structures. Because changes to reactor design may influence interior, thermal-hydraulic characteristics, licensing applicants commonly conduct a flow-distribution test and use test results (e.g., core-inlet flow-rate distribution) as the input data for a core thermal-margin analysis program. Because the APR+ (Advanced Power Reactor Plus) had more fuel assemblies (241EA → 257EA) and the design of some internal structures was changed (from those of APR1400), the core-inlet flow-rate distribution for a 1/5 scaled-down reactor model was measured and high flow-rates were found especially near the outer region of the reactor core. In this study, to examine the effect of the holes size change (i.e. smaller diameter) in the outer region of the LSSBP, not a 50% blockage of the flow holes, on the reactor core-inlet flow-distribution, simulations were conducted with the commercial CFD (Computational Fluid Dynamics) software, ANSYS CFX R.14. The predicted results were compared with those of the original LSSBP. In this study, to examine the effect of the holes size change (smaller diameter) in the outer region of the LSSBP on the reactor core-inlet flow-distribution, simulations were conducted with the commercial CFD software, ANSYS CFX R.14. The predicted results were compared with those of the original LSSBP. Through these comparisons it was concluded that a more uniform distribution of the mass-flow rate at the core-inlet plane could be obtained by reducing the holes size in the outer region of the LSSBP

Black hole astrophysics

International Nuclear Information System (INIS)

Blandford, R.D.; Thorne, K.S.

1979-01-01

Following an introductory section, the subject is discussed under the headings: on the character of research in black hole astrophysics; isolated holes produced by collapse of normal stars; black holes in binary systems; black holes in globular clusters; black holes in quasars and active galactic nuclei; primordial black holes; concluding remarks on the present state of research in black hole astrophysics. (U.K.)

Development of debris resistant bottom end piece

International Nuclear Information System (INIS)

Lee, Jae Kyung; Sohn, Dong Seong; Yim, Jeong Sik; Hwang, Dae Hyun; Song, Kee Nam; Oh, Dong Seok; Rhu, Ho Sik; Lee, Chang Woo; Kim, Seong Soo; Oh, Jong Myung

1993-12-01

Debris-related fuel failures have been identified as one of the major causes of fuel failures. In order to reduce the possibility of debris-related fuel failures, it is necessary to develop Debris-Resistant Bottom End Piece. For this development, mechanical strength test and pressure drop test were performed, and the test results were analyzed. And the laser cutting, laser welding and electron beam welding technology, which were the core manufacturing technology of DRBEP, were developed. Final design were performed, and the final drawing and specifications were prepared. The prototype of DRBEP was manufactured according to the developed munufacturing procedure. (Author)

Van der Waals black hole

Directory of Open Access Journals (Sweden)

Aruna Rajagopal

2014-10-01

Full Text Available In the context of extended phase space, where the negative cosmological constant is treated as a thermodynamic pressure in the first law of black hole thermodynamics, we find an asymptotically AdS metric whose thermodynamics matches exactly that of the Van der Waals fluid. We show that as a solution of Einstein's equations, the corresponding stress energy tensor obeys (at least for certain range of metric parameters all three weak, strong, and dominant energy conditions.

Insight into black hole phase transition from parametric solutions

Science.gov (United States)

Li, Dandan; Li, Shanshan; Mi, Li-Qin; Li, Zhong-Heng

2017-12-01

We consider the first-order phase transition of a charged anti-de Sitter black hole and introduce a new dimensionless parameter, ω =(Δ S /π Q2)2 . The parametric solutions of the two reduced volumes are obtained. Each volume is described by a piecewise analytic function. The demarcation point is located at ωd=12 (2 √{3 }-3 ). The volume function is smoothly connected at the point. We show that all properties of the coexistence curve can be studied from the two volume functions. In other words, an arbitrary reduced thermodynamic variable of the two coexisting phases is only a function of ω . Some phase diagrams are plotted by using parametric solutions. We find that, when the reduced pressure P ^>P^A (of order 7.4 ×10-4), the first-order phase transition of the black hole is similar to the van der Waals fluid. However, the similarity disappears when P ^≤P^A. At a van der Waals fluidlike stage, the values of the reduced Gibbs function and the reduced density average are equal. At a non-van der Waals fluid stage, the phase diagrams have extraordinarily rich structure. It is worth pointing out that the phase transition is very important for the low-pressure case since the pressure in essence is the cosmological constant, which is normally very small. Moreover, the thermodynamic behaviors as ω →0 are discussed, from which one can easily obtain some critical exponents and amplitudes for small-large black hole phase transitions.

Configurational entropy of charged AdS black holes

Directory of Open Access Journals (Sweden)

Chong Oh Lee

2017-09-01

Full Text Available When we consider charged AdS black holes in higher dimensional spacetime and a molecule number density along coexistence curves is numerically extended to higher dimensional cases. It is found that a number density difference of a small and large black holes decrease as a total dimension grows up. In particular, we find that a configurational entropy is a concave function of a reduced temperature and reaches a maximum value at a critical (second-order phase transition point. Furthermore, the bigger a total dimension becomes, the more concave function in a configurational entropy while the more convex function in a reduced pressure.

A Miniature Four-Hole Probe for Measurement of Three-Dimensional Flow with Large Gradients

Directory of Open Access Journals (Sweden)

Ravirai Jangir

2014-01-01

Full Text Available A miniature four-hole probe with a sensing area of 1.284 mm2 to minimise the measurement errors due to the large pressure and velocity gradients that occur in highly three-dimensional turbomachinery flows is designed, fabricated, calibrated, and validated. The probe has good spatial resolution in two directions, thus minimising spatial and flow gradient errors. The probe is calibrated in an open jet calibration tunnel at a velocity of 50 m/s in yaw and pitch angles range of ±40 degrees with an interval of 5 degrees. The calibration coefficients are defined, determined, and presented. Sensitivity coefficients are also calculated and presented. A lookup table method is used to determine the four unknown quantities, namely, total and static pressures and flow angles. The maximum absolute errors in yaw and pitch angles are 2.4 and 1.3 deg., respectively. The maximum absolute errors in total, static, and dynamic pressures are 3.4, 3.9, and 4.9% of the dynamic pressures, respectively. Measurements made with this probe, a conventional five-hole probe and a miniature Pitot probe across a calibration section, demonstrated that the errors due to gradient and surface proximity for this probe are considerably reduced compared to the five-hole probe.

Ultraclean single, double, and triple carbon nanotube quantum dots with recessed Re bottom gates

Science.gov (United States)

Jung, Minkyung; Schindele, Jens; Nau, Stefan; Weiss, Markus; Baumgartner, Andreas; Schoenenberger, Christian

2014-03-01

Ultraclean carbon nanotubes (CNTs) that are free from disorder provide a promising platform to manipulate single electron or hole spins for quantum information. Here, we demonstrate that ultraclean single, double, and triple quantum dots (QDs) can be formed reliably in a CNT by a straightforward fabrication technique. The QDs are electrostatically defined in the CNT by closely spaced metallic bottom gates deposited in trenches in Silicon dioxide by sputter deposition of Re. The carbon nanotubes are then grown by chemical vapor deposition (CVD) across the trenches and contacted using conventional electron beam lithography. The devices exhibit reproducibly the characteristics of ultraclean QDs behavior even after the subsequent electron beam lithography and chemical processing steps. We demonstrate the high quality using CNT devices with two narrow bottom gates and one global back gate. Tunable by the gate voltages, the device can be operated in four different regimes: i) fully p-type with ballistic transport between the outermost contacts (over a length of 700 nm), ii) clean n-type single QD behavior where a QD can be induced by either the left or the right bottom gate, iii) n-type double QD and iv) triple bipolar QD where the middle QD has opposite doping (p-type). Research at Basel is supported by the NCCR-Nano, NCCR-QIST, ERC project QUEST, and FP7 project SE2ND.

Study on Gap Flow Field Simulation in Small Hole Machining of Ultrasonic Assisted EDM

Science.gov (United States)

Liu, Yu; Chang, Hao; Zhang, Wenchao; Ma, Fujian; Sha, Zhihua; Zhang, Shengfang

2017-12-01

When machining a small hole with high aspect ratio in EDM, it is hard for the flushing liquid entering the bottom gap and the debris could hardly be removed, which results in the accumulation of debris and affects the machining efficiency and machining accuracy. The assisted ultrasonic vibration can improve the removal of debris in the gap. Based on dynamics simulation software Fluent, a 3D model of debris movement in the gap flow field of EDM small hole machining assisted with side flushing and ultrasonic vibration is established in this paper. When depth to ratio is 3, the laws of different amplitudes and frequencies on debris distribution and removal are quantitatively analysed. The research results show that periodic ultrasonic vibration can promote the movement of debris, which is beneficial to the removal of debris in the machining gap. Compared to traditional small hole machining in EDM, the debris in the machining gap is greatly reduced, which ensures the stability of machining process and improves the machining efficiency.

SHORT-PULSE ELECTROMAGNETIC TRANSPONDER FOR HOLE-TO-HOLE USE.

Science.gov (United States)

Wright, David L.; Watts, Raymond D.; Bramsoe, Erik

1983-01-01

Hole-to-hole observations were made through nearly 20 m of granite using an electromagnetic transponder (an active reflector) in one borehole and a single-hole short-pulse radar in another. The transponder is inexpensive, operationally simple, and effective in extending the capability of a short-pulse borehole radar system to allow hole-to-hole operation without requiring timing cables. A detector in the transponder senses the arrival of each pulse from the radar. Each pulse detection triggers a kilovolt-amplitude pulse for retransmission. The transponder 'echo' may be stronger than that of a passive reflector by a factor of as much as 120 db. The result is an increase in range capability by a factor which depends on attenuation in the medium and hole-to-hole wavepath geometry.

Black holes

OpenAIRE

Brügmann, B.; Ghez, A. M.; Greiner, J.

2001-01-01

Recent progress in black hole research is illustrated by three examples. We discuss the observational challenges that were met to show that a supermassive black hole exists at the center of our galaxy. Stellar-size black holes have been studied in x-ray binaries and microquasars. Finally, numerical simulations have become possible for the merger of black hole binaries.

Influence of boundary geometry in domain wall propagation in magnetic films with asymmetric holes: Micromagnetic calculations

International Nuclear Information System (INIS)

Alija, A; Sobrado, I; Rodriguez-RodrIguez, G; Velez, M; Alameda, J M; MartIn, J I; Parrondo, J M R

2010-01-01

Micromagnetic simulations have been performed in uniaxial magnetic films with 2D array of asymmetric arrow shape holes. In order to understand the asymmetric pinning potential created by the holes, different boundary geometries conditions are used on the simulations. The depinning fields for forward and backward domain wall propagation have been calculated by the analysis of the energy landscapes as a function of the domain wall position. Domain wall depinning occurs preferentially at the free ends of the domain wall at the film boundaries. We have found that the domain wall propagation is different at the top/bottom boundaries of the simulated film which can be understood in terms of the magnetostatic energy and the chirality of the domain wall.

Plasma dynamics near critical density inferred from direct measurements of laser hole boring

Science.gov (United States)

Gong, Chao; Tochitsky, Sergei Ya.; Fiuza, Frederico; Pigeon, Jeremy J.; Joshi, Chan

2016-06-01

We have used multiframe picosecond optical interferometry to make direct measurements of the hole boring velocity, vHB, of the density cavity pushed forward by a train of C O2 laser pulses in a near critical density helium plasma. As the pulse train intensity rises, the increasing radiation pressure of each pulse pushes the density cavity forward and the plasma electrons are strongly heated. After the peak laser intensity, the plasma pressure exerted by the heated electrons strongly impedes the hole boring process and the vHB falls rapidly as the laser pulse intensity falls at the back of the laser pulse train. A heuristic theory is presented that allows the estimation of the plasma electron temperature from the measurements of the hole boring velocity. The measured values of vHB, and the estimated values of the heated electron temperature as a function of laser intensity are in reasonable agreement with those obtained from two-dimensional numerical simulations.

Eddy current testing system for bottom mounted instrumentation welds

OpenAIRE

Kobayashi Noriyasu; Ueno Souichi; Suganuma Naotaka; Oodake Tatsuya; Maehara Takeshi; Kasuya Takashi; Ichikawa Hiroya

2015-01-01

The capability of eddy current testing (ECT) for the bottom mounted instrumentation (BMI) weld area of reactor vessel in a pressurized water reactor was demonstrated by the developed ECT system and procedure. It is difficult to position and move the probe on the BMI weld area because the area has complexly curved surfaces. The space coordinates and the normal vectors at the scanning points were calculated as the scanning trajectory of probe based on the measured results of surface shape on th...

Slamming pressures on the bottom of a free-falling vertical wedge

Science.gov (United States)

Ikeda, C. M.; Judge, C. Q.

2013-11-01

High-speed planing boats are subjected to repeat impacts due to slamming, which can cause structural damage and injury to passengers. A first step in understanding and predicting the physics of a craft re-entering the water after becoming partially airborne is an experimental vertical drop test of a prismastic wedge (deadrise angle, β =20° beam, B = 300 mm; and length, L = 600 mm). The acrylic wedge was mounted to a rig allowing it to free-fall into a deep-water tank (5.2m × 5.2m × 4.2m deep) from heights 0 camera (1000 fps, resolution of 1920 × 1200 pixels) is mounted above the wedge model to record the wetted surface as the wedge descended below the free surface. The pressure measurements taken with both conventional surface pressure transducers and the pressure mapping system agree within 10% of the peak pressure values (0.7 bar, typical). Supported by the Office of Naval Research.

Bottom sample taker

Energy Technology Data Exchange (ETDEWEB)

Garbarenko, O V; Slonimskiy, L D

1982-01-01

In order to improve the quality of the samples taken during offshore exploration from benthic sediments, the proposed design of the sample taker has a device which makes it possible to regulate the depth of submersion of the core lifter. For this purpose the upper part of the core lifter has an inner delimiting ring, and within the core lifter there is a piston suspended on a cable. The position of the piston in relation to the core lifter is previously assigned depending on the compactness of the benthic sediments and is fixed by tension of the cable which is held by a clamp in the cover of the core taker housing. When lowered to the bottom, the core taker is released, and under the influence of hydrostatic pressure of sea water, it enters the sediments. The magnitude of penetration is limited by the distance between the piston and the stopping ring. The piston also guarantees better preservation of the sample when the instrument is lifted to the surface.

Neutrino constraints that transform black holes into grey holes

International Nuclear Information System (INIS)

Ruderfer, M.

1982-01-01

Existing black hole theory is found to be defective in its neglect of the physical properties of matter and radiation at superhigh densities. Nongravitational neutrino effects are shown to be physically relevant to the evolution of astronomical black holes and their equations of state. Gravitational collapse to supernovae combined with the Davis and Ray vacuum solution for neutrinos limit attainment of a singularity and require black holes to evolve into ''grey holes''. These allow a better justification than do black holes for explaining the unique existence of galactic masses. (Auth.)

Bubble-induced mixing of two horizontal liquid layers with non-uniform gas injection at the bottom

International Nuclear Information System (INIS)

Cheung, F.B.; Pedersen, D.R.; Leinweber, G.

1986-01-01

During a postulated severe core meltdown accident in an LMFBR, a large amount of sodium coolant may spill into the reactor concrete cavity. A layer of liquid products may form as a result of the sodium-concrete reactions. The liquid product layer, which is highly viscous and much heavier than sodium, separates the concrete from the sodium pool. In general, the downward transport of sodium through the liquid product layer to the unreacted concrete surface, which controls the rate of chemical erosion of the concrete, depends strongly on the agitation induced by gas evolution from the heated concrete. In this study, experiments were conducted to explore the effect of non-uniform gas injection on mixing of two horizontal mutually soluble liquid layers. The liquid in the lower layer was chosen to be more viscous and heavier than the liquid in the upper layer. To simulate the reactor accident situation, gas was injected at the bottom of the liquid-liquid system through a circular hole that covered only the center portion of the bottom surface of the lower liquid layer. The bubble-induced mixing motions were observed and the rate of mixing was measured for different hole sizes and various gas flow rates. The results of this study clearly show that the rate of gas injection is not the only parameter controlling the mixing of the liquid-liquid system. The effect of non-uniform gas injection is important at high gas flow rates. Within the present experimental conditions, the reduction in the overall mixing rate can be as large as a factor of three

Drilling and the associated drillhole measurements of the pilot hole ONK-PH7

International Nuclear Information System (INIS)

Oehberg, A.; Kemppainen, K.; Lampinen, H.; Niemonen, J.; Poelloenen, J.; Rouhiainen, P.; Rautio, T.; Tarvainen, A.-M.

2007-12-01

The construction of the ONKALO access tunnel started in September 2004 at Olkiluoto. Most of the investigations related to the construction of the access tunnel aim to ensure successful excavations, reinforcement and sealing. Pilot holes are drillholes, which are core drilled along the tunnel profile. The length of the pilot holes typically varies from several tens of metres to a couple of hundred metres. The pilot holes are aimed to confirm the quality of the rock mass for tunnel construction, and in particular to identify water conductive fractured zones and to provide information that could result in modifications of the existing construction plans. The pilot hole ONK-PH7 was drilled from chainage 1880 to chainage 1980.31 in February 2007. The length of the hole is 100.31 m. The aim during the drilling work was to orient core samples as much as possible. The deviation of the drillhole was measured during and after the drilling phase. Electric conductivity was measured from the collected returning water samples. Logging of the core samples included the following parameters: lithology, foliation, fracturing, fracture frequency, RQD, fractured zones, core loss and weathering. The rock mechanical logging was based on Q-classification. The tests to determine rock strength and deformation properties were made with a Rock Tester-equipment. Difference Flow method was used for the determination of hydraulic conductivity in fractures and fractured zones in the drillhole. The overlapping i.e. the detailed flow logging mode was used. Besides flow logging Single Point Resistance (SPR), Electric Conductivity (EC) and temperature of the drillhole water were also measured. The flow logging was performed with 0.5 m section length and with 0.1 m depth increment. Water loss measurements were conducted between the hole depth of 1.18 m and the hole bottom. Geophysical logging and optical imaging of the pilot hole included the fieldwork of all surveys, the integration of the data as

Bottom friction models for shallow water equations: Manning’s roughness coefficient and small-scale bottom heterogeneity

Science.gov (United States)

Dyakonova, Tatyana; Khoperskov, Alexander

2018-03-01

The correct description of the surface water dynamics in the model of shallow water requires accounting for friction. To simulate a channel flow in the Chezy model the constant Manning roughness coefficient is frequently used. The Manning coefficient nM is an integral parameter which accounts for a large number of physical factors determining the flow braking. We used computational simulations in a shallow water model to determine the relationship between the Manning coefficient and the parameters of small-scale perturbations of a bottom in a long channel. Comparing the transverse water velocity profiles in the channel obtained in the models with a perturbed bottom without bottom friction and with bottom friction on a smooth bottom, we constructed the dependence of nM on the amplitude and spatial scale of perturbation of the bottom relief.

Experiments to investigate direct containment heating phenomena with scaled models of the Zion Nuclear Power Plant in the Surtsey Test Facility

International Nuclear Information System (INIS)

Allen, M.D.; Pilch, M.M.; Blanchat, T.K.; Griffith, R.O.; Nichols, R.T.

1994-05-01

The Surtsey Facility at Sandia National Laboratories (SNL) is used to perform scaled experiments that simulate hypothetical high-pressure melt ejection (HPME) accidents in a nuclear power plant (NPP). These experiments are designed to investigate the effect of specific phenomena associated with direct containment heating (DCH) on the containment load, such as the effect of physical scale, prototypic subcompartment structures, water in the cavity, and hydrogen generation and combustion. In the Integral Effects Test (IET) series, 1:10 linear scale models of the Zion NPP structures were constructed in the Surtsey vessel. The RPV was modeled with a steel pressure vessel that had a hemispherical bottom head, which had a 4-cm hole in the bottom head that simulated the final ablated hole that would be formed by ejection of an instrument guide tube in a severe NPP accident. Iron/alumina/chromium thermite was used to simulate molten corium that would accumulate on the bottom head of an actual RPV. The chemically reactive melt simulant was ejected by high-pressure steam from the RPV model into the scaled reactor cavity. Debris was then entrained through the instrument tunnel into the subcompartment structures and the upper dome of the simulated reactor containment building. The results of the IET experiments are given in this report

Experiments to investigate direct containment heating phenomena with scaled models of the Zion Nuclear Power Plant in the Surtsey Test Facility

Energy Technology Data Exchange (ETDEWEB)

Allen, M.D.; Pilch, M.M.; Blanchat, T.K.; Griffith, R.O. [Sandia National Labs., Albuquerque, NM (United States); Nichols, R.T. [Ktech Corp., Albuquerque, NM (United States)

1994-05-01

The Surtsey Facility at Sandia National Laboratories (SNL) is used to perform scaled experiments that simulate hypothetical high-pressure melt ejection (HPME) accidents in a nuclear power plant (NPP). These experiments are designed to investigate the effect of specific phenomena associated with direct containment heating (DCH) on the containment load, such as the effect of physical scale, prototypic subcompartment structures, water in the cavity, and hydrogen generation and combustion. In the Integral Effects Test (IET) series, 1:10 linear scale models of the Zion NPP structures were constructed in the Surtsey vessel. The RPV was modeled with a steel pressure vessel that had a hemispherical bottom head, which had a 4-cm hole in the bottom head that simulated the final ablated hole that would be formed by ejection of an instrument guide tube in a severe NPP accident. Iron/alumina/chromium thermite was used to simulate molten corium that would accumulate on the bottom head of an actual RPV. The chemically reactive melt simulant was ejected by high-pressure steam from the RPV model into the scaled reactor cavity. Debris was then entrained through the instrument tunnel into the subcompartment structures and the upper dome of the simulated reactor containment building. The results of the IET experiments are given in this report.

Numerical Analysis of Heat transfer Enhancement in a double pipe heat exchanger with a holed twisted tape

Directory of Open Access Journals (Sweden)

Kumar Akarsh

2018-01-01

Full Text Available In the present study numerical analysis of enhancement in heat transfer characteristics in a double pipe heat exchanger is studied using a holed twisted tape.The twisted tape with a constant twist ratio is inserted in a double pipe heat exchanger. Holes of diameter 1mm, 3 mm and 5 mm were drilled at regular pitch throughout the length of the tape. Numerical modeling of a double pipe heat exchanger with the holed twisted tape was constructed considering hot fluid flowing in the inner pipe and cold fluid through the annulus.Simulation was done for varied mass flow rates of hot fluid in the turbulent condition keeping the mass flow rate of cold fluid being constant. Thermal properties like Outlet temperatures, Nusselt number, overall heat transfer coefficient, heat transfer rate and pressure drop were determined for all the cases. Results indicated that normaltwisted tape without holes performed better than the bare tube. In the tested range of mass flow rates the average Nusselt number and heat transfer rate were increased by 85% and 34% respectively. Performance of Twisted tape with holes was slightly reduced than the normal twisted tape and it deteriorated further for higher values hole diameter. Pressure drop was found to be higher for the holed twisted tape than the normal tape.

Number and location of drainage catheter side holes: in vitro evaluation.

Science.gov (United States)

Ballard, D H; Alexander, J S; Weisman, J A; Orchard, M A; Williams, J T; D'Agostino, H B

2015-09-01

To evaluate the influence of number and location of catheter shaft side holes regarding drainage efficiency in an in vitro model. Three different drainage catheter models were constructed: open-ended model with no side holes (one catheter), unilateral side hole model (six catheters with one to six unilateral side holes), and bilateral side hole model (six catheters with one to six bilateral side holes). Catheters were inserted into a drainage output-measuring device with a constant-pressure reservoir of water. The volume of water evacuated by each of the catheters at 10-second intervals was measured. A total of five trials were performed for each catheter. Data were analysed using one-way analysis of variance. The open-ended catheter had a mean drainage volume comparable to the unilateral model catheters with three, four, and five side holes. Unilateral model catheters had significant drainage volume increases up to three side holes; unilateral model catheters with more than three side holes had no significant improvement in drainage volume. All bilateral model catheters had significantly higher mean drainage volumes than their unilateral counterparts. There was no significant difference between the mean drainage volume with one, two, or three pairs of bilateral side holes. Further, there was no drainage improvement by adding additional bilateral side holes. The present in vitro study suggests that beyond a critical side hole number threshold, adding more distal side holes does not improve catheter drainage efficiency. These results may be used to enhance catheter design towards improving their drainage efficiency. Copyright © 2015 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

Critical behavior and phase transition of dilaton black holes with nonlinear electrodynamics

Energy Technology Data Exchange (ETDEWEB)

Dayyani, Z.; Dehghani, M.H.; Hajkhalili, S. [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of); Sheykhi, A. [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of); Research Institute for Astronomy and Astrophysics of Maragha (RIAAM), Maragha (Iran, Islamic Republic of)

2018-02-15

In this paper, we take into account the dilaton black hole solutions of Einstein gravity in the presence of logarithmic and exponential forms of nonlinear electrodynamics. First of all, we consider the cosmological constant and nonlinear parameter as thermodynamic quantities which can vary. We obtain thermodynamic quantities of the system such as pressure, temperature and Gibbs free energy in an extended phase space. We complete the analogy of the nonlinear dilaton black holes with the Van der Waals liquid-gas system. We work in the canonical ensemble and hence we treat the charge of the black hole as an external fixed parameter. Moreover, we calculate the critical values of temperature, volume and pressure and show that they depend on the dilaton coupling constant as well as on the nonlinear parameter. We also investigate the critical exponents and find that they are universal and independent of the dilaton and nonlinear parameters, which is an expected result. Finally, we explore the phase transition of nonlinear dilaton black holes by studying the Gibbs free energy of the system. We find that in the case of T > T{sub c}, we have no phase transition. When T = T{sub c}, the system admits a second-order phase transition, while for T = T{sub f} < T{sub c} the system experiences a first-order transition. Interestingly, for T{sub f} < T < T{sub c} we observe a zeroth-order phase transition in the presence of a dilaton field. This novel zeroth-order phase transition occurs due to a finite jump in the Gibbs free energy which is generated by the dilaton-electromagnetic coupling constant, α, for a certain range of pressure. (orig.)

Bottom-linked innovation

DEFF Research Database (Denmark)

Kristensen, Catharina Juul

2018-01-01

hitherto been paid little explicit attention, namely collaboration between middle managers and employees in innovation processes. In contrast to most studies, middle managers and employees are here both subjects of explicit investigation. The collaboration processes explored in this article are termed...... ‘bottom-linked innovation’. The empirical analysis is based on an in-depth qualitative study of bottom-linked innovation in a public frontline institution in Denmark. By combining research on employee-driven innovation and middle management, the article offers new insights into such collaborative......Employee-driven innovation is gaining ground as a strategy for developing sustainable organisations in the public and private sector. This type of innovation is characterised by active employee participation, and the bottom-up perspective is often emphasised. This article explores an issue that has...

Validation of the Engineering Plant Analyzer methodology with Peach Bottom 2 stability tests

International Nuclear Information System (INIS)

Rohatgi, U.S.; Mallen, A.N.; Cheng, H.S.; Wulff, W.

1994-01-01

The Engineering Plant Analyzer (EPA) had been developed in 1984 at Brookhaven National Laboratory to simulate plant transients in boiling water reactors (BWR). Recently, the EPA with its High-Speed Interactive Plant Analyzer code for BWRs ( ppercase HIPA-BWR ) simulated for the first time oscillatory transients with large, non-linear power and flow amplitudes; transients which are centered around the March 9, 1988 instability at the LaSalle-2 BWR power plant.The EPA's capability to simulate oscillatory transients has been demonstrated first by comparing simulation results with LaSalle-2 plant data (Wulff et al., NUREG/CR-5816, BNL-NUREG-52312, Brookhaven National Laboratory, 1992). This paper presents an EPA assessment on the basis of the Peach Bottom 2 instability tests (Carmichael and Niemi, EPRI NP-564, Electric Power Research Institute, Palo Alto, CA, 1978). This assessment of the EPA appears to constitute the first validation of a time-domain reactor systems code on the basis of frequency-domain criteria, namely power spectral density, gain and phase shift of the pressure-to-power transfer function.The reactor system pressure was disturbed in the Peach Bottom 2 power plant tests, and in their EPA simulation, by a pseudo-random, binary sequence signal. The data comparison revealed that the EPA predicted for Peach Bottom tests PT1, PT2, and PT4 the gain of the power-to-pressure transfer function with the biases and standard deviations of (-10±28)%, (-1±40)% and (+28±52)%, respectively. The respective frequencies at the peak gains were predicted with the errors of +6%, +3%, and -28%. The differences between the predicted and the measured phase shift increased with increasing frequency, but stayed within the margin of experimental uncertainty. ((orig.))

ULF/VLF (0.001 to 50 Hz) Seismo-Acoustic Noise in the Ocean. Proceedings of a Workshop Held at Austin, Texas on November 29-December 1, 1988

Science.gov (United States)

1989-08-03

holes drilled in the seafloor from the D/V JOIDES Resolution through petrological , geochemical and paleomagnetic studies of the samples and logging...seismome- ters and/or hydrophones (or differential pressure gauges , DPG). Testing of the new instruments at very early stages is important to ensure...resolved using ocean bottom seismometers, suspended hydrophones and differential pressure gauges assisted by an orbiting radar altimeter (GEOSAT

Filling or Draining a Water Bottle with Two Holes

Science.gov (United States)

Cross, Rod

2016-01-01

Three simple experiments are described using a small water bottle with two holes in the side of the bottle. The main challenge is to predict and then explain the observations, but the arrangements can also be used for quantitative measurements concerning hydrostatic pressure, Bernoulli's equation, surface tension and bubble formation.

From binary black hole simulation to triple black hole simulation

International Nuclear Information System (INIS)

Bai Shan; Cao Zhoujian; Han, Wen-Biao; Lin, Chun-Yu; Yo, Hwei-Jang; Yu, Jui-Ping

2011-01-01

Black hole systems are among the most promising sources for a gravitational wave detection project. Now, China is planning to construct a space-based laser interferometric detector as a follow-on mission of LISA in the near future. Aiming to provide some theoretical support to this detection project on the numerical relativity side, we focus on black hole systems simulation in this work. Considering the globular galaxy, multiple black hole systems also likely to exist in our universe and play a role as a source for the gravitational wave detector we are considering. We will give a progress report in this paper on our black hole system simulation. More specifically, we will present triple black hole simulation together with binary black hole simulation. On triple black hole simulations, one novel perturbational method is proposed.

Phase transition for black holes with scalar hair and topological black holes

International Nuclear Information System (INIS)

Myung, Yun Soo

2008-01-01

We study phase transitions between black holes with scalar hair and topological black holes in asymptotically anti-de Sitter spacetimes. As the ground state solutions, we introduce the non-rotating BTZ black hole in three dimensions and topological black hole with hyperbolic horizon in four dimensions. For the temperature matching only, we show that the phase transition between black hole with scalar hair (Martinez-Troncoso-Zanelli black hole) and topological black hole is second-order by using differences between two free energies. However, we do not identify what order of the phase transition between scalar and non-rotating BTZ black holes occurs in three dimensions, although there exists a possible decay of scalar black hole to non-rotating BTZ black hole

Black Holes

OpenAIRE

Townsend, P. K.

1997-01-01

This paper is concerned with several not-quantum aspects of black holes, with emphasis on theoretical and mathematical issues related to numerical modeling of black hole space-times. Part of the material has a review character, but some new results or proposals are also presented. We review the experimental evidence for existence of black holes. We propose a definition of black hole region for any theory governed by a symmetric hyperbolic system of equations. Our definition reproduces the usu...

Application and Development of an Environmentally Friendly Blast Hole Plug for Underground Coal Mines

Directory of Open Access Journals (Sweden)

Donghui Yang

2018-01-01

Full Text Available Drilling and blasting technology is one of the main methods for pressure relief in deep mining. The traditional method for blasting hole blockage with clay stemming has many problems, which include a large volume of transportation, excess loading time, and high labor intensity. An environmentally friendly blast hole plug was designed and developed. This method is cheap, closely blocks the hole, is quickly loaded, and is convenient for transportation. The impact test on the plug was carried out using an improved split Hopkinson pressure bar test system, and the industrial test was carried out in underground tunnel of coal mine. The tests results showed that, compared with clay stemming, the new method proposed in this paper could prolong the action time of the detonation gas, prevent premature detonation gas emissions, reduce the unit consumption of explosives, improve the utilization ratio, reduce the labor intensity of workers, and improve the effect of rock blasting with low cost of rock breaking.

Trends in Arctic Ocean bottom pressure, sea surface height and freshwater content using GRACE and the ice-ocean model PIOMAS from 2008-2012

Science.gov (United States)

Peralta-Ferriz, Cecilia; Morison, James; Zhang, Jinlun; Bonin, Jennifer

2014-05-01

The variability of ocean bottom pressure (OBP) in the Arctic is dominated by the variations in sea surface height (SSH) from daily to monthly timescales. Conversely, OBP variability is dominated by the changes in the steric pressure (StP) at inter-annual timescales, particularly off the continental shelves. The combination of GRACE-derived ocean bottom pressure and ICESat altimetry-derived sea surface height variations in the Arctic Ocean have provided new means of identifying inter-annual trends in StP (StP = OBP-SSH) and associated freshwater content (FWC) of the Arctic region (Morison et al., 2012). Morison et al. (2012) showed that from 2004 to 2008, the FWC increased in the Beaufort Gyre and decreased in the Siberian and Central Arctic, resulting in a relatively small net basin-averaged FWC change. In this work, we investigate the inter-annual trends from 2008 to 2012 in OBP from GRACE, SSH from the state-of-the-art pan-Arctic ocean model PIOMAS -validated with tide and pressure gauges in the Arctic-, and compute the trends in StP and FWC from 2008-2012. We compare these results with the previous trends from 2005-2008 described in Morison et al. (2012). Our initial findings suggest increased salinity in the entire Arctic basin (relative to the climatological seasonal variation) from 2008-2012, compared to the preceding four years (2005-2008). We also find that the trends in OBP, SSH and StP from 2008-2012 present a different behavior during the spring-summer and fall-winter, unlike 2005-2008, in which the trends were generally consistent through all months of the year. It seems since 2009, when the Beaufort Gyre relaxed and the export of freshwater from the Canada Basin into the Canadian Archipelago and Fram Strait, via the Lincoln Sea, was anomalously large (de Steur et al., 2013), the Arctic Ocean has entered a new circulation regime. The causes of such changes in the inter-annual trends of OBP, SSH and StP -hence FWC-, associated with the changes in the

Effect of Boundary-Layer Bleed Hole Inclination Angle and Scaling on Flow Coefficient Behavior

Science.gov (United States)

Eichorn, Michael B.; Barnhart, Paul J.; Davis, David O.; Vyas, Manan A.; Slater, John W.

2013-01-01

Phase II data results of the Fundamental Inlet Bleed Experiments study at NASA Glenn Research Center are presented which include flow coefficient behavior for 21 bleed hole configurations. The bleed configurations are all round holes with hole diameters ranging from 0.795 to 6.35 mm, hole inclination angles from 20deg to 90deg, and thickness-to-diameter ratios from 0.25 to 2.0. All configurations were tested at a unit Reynolds number of 2.46 10(exp 7)/m and at discrete local Mach numbers of 1.33, 1.62, 1.98, 2.46, and 2.92. Interactions between the design parameters of hole diameter, hole inclination angle, and thickness-to-diameter as well as the interactions between the flow parameters of pressure ratio and Mach number upon the flow coefficient are examined, and a preliminary statistical model is proposed. An existing correlation is also examined with respect to this data.

The impact of mass flow and masking on the pressure drop of air filter in heavy-duty diesel engine

Directory of Open Access Journals (Sweden)

Gorji-Bandpy Mofid

2012-04-01

Full Text Available This paper presents a computational fluid dynamics (CFD calculation approach to predict and evaluate the impact of the mass-flow inlet on the pressure drop of turbocharger`s air filtfer in heavy-duty diesel engine. The numerical computations were carried out using a commercial CFD program whereas the inlet area of the air filter consisted of several holes connected to a channel. After entering through the channel, the air passes among the holes and enters the air filter. The effect of masking holes and hydraulic diameter is studied and investigated on pressure drop. The results indicate that pressure drop increase with decreasing of hydraulic diameter and masking of the holes has considerable affect on the pressure drop.

Empty black holes, firewalls, and the origin of Bekenstein-Hawking entropy

Science.gov (United States)

Saravani, Mehdi; Afshordi, Niayesh; Mann, Robert B.

2014-01-01

We propose a novel solution for the endpoint of gravitational collapse, in which spacetime ends (and is orbifolded) at a microscopic distance from black hole event horizons. This model is motivated by the emergence of singular event horizons in the gravitational aether theory, a semiclassical solution to the cosmological constant problem(s) and thus suggests a catastrophic breakdown of general relativity close to black hole event horizons. A similar picture emerges in fuzzball models of black holes in string theory, as well as the recent firewall proposal to resolve the information paradox. We then demonstrate that positing a surface fluid in thermal equilibrium with Hawking radiation, with vanishing energy density (but nonvanishing pressure) at the new boundary of spacetime, which is required by Israel junction conditions, yields a thermodynamic entropy that is identical to the Bekenstein-Hawking area law, SBH, for charged rotating black holes. To our knowledge, this is the first derivation of black hole entropy that only employs local thermodynamics. Furthermore, a model for the microscopic degrees of freedom of the surface fluid (which constitute the microstates of the black hole) is suggested, which has a finite, but Lorentz-violating, quantum field theory. Finally, we comment on the effects of physical boundary on Hawking radiation and show that relaxing the assumption of equilibrium with Hawking radiation sets SBH as an upper limit for Black Hole entropy.

Black Holes with Anisotropic Fluid in Lyra Scalar-Tensor Theory

Directory of Open Access Journals (Sweden)

Melis ULU DOĞRU

2018-02-01

Full Text Available In this paper, we investigate distribution of anisotropic fluid which is a resource of black holes in regard to Lyra scalar-tensor theory. As part of the theory, we obtain field equations of spherically symmetric space-time with anisotropic fluid. By using field equations, we suggest distribution of anisotropic fluid, responsible for space-time geometries such as Schwarzschild, Reissner-Nordström, Minkowski type, de Sitter type, Anti-de Sitter type, BTZ and charged BTZ black holes. Finally, we discuss obtained pressures and density of the fluid for different values of arbitrary constants, geometrically and physically.

Ulysses' rapid crossing of the polar coronal hole boundary

International Nuclear Information System (INIS)

McComas, D.J.; Riley, P.; Gosling, J.T.; Balogh, A.; Forsyth, R.

1998-01-01

The Ulysses spacecraft crossed from the slow dense solar wind characteristic of the solar streamer belt into the fast, less dense flow from the northern polar coronal hole over a very short interval (several days) in late March 1995. The spacecraft, which was at 1.35 AU and ∼19 degree north heliographic latitude, moving northward in its orbit, remained in the fast solar wind from then through summer 1996. This boundary crossing is unique in that the combination of the spacecraft motion and rotation of the structure past the spacecraft caused Ulysses to move smoothly and completely from one regime into the other. In this study we examine this crossing in detail. The crossing is marked by a region of enhanced pressure, typical of stream interaction regions, which extends ∼2x10 7 km across. We find that the transition between the slow and fast regimes occurs on several temporal, and hence spatial, scales. On the shortest scale ( 4 km) the stream interface is a tangential discontinuity where the proton and core electron densities and ion and electron pressures all drop while the magnetic pressure jumps to maintain a rough pressure balance. The alpha to proton ratio also jumps across the stream interface to reach the comparatively constant polar hole value of ∼4.3%. On larger scales (a few x10 6 km) the proton and alpha temperatures rise to their high-speed wind values. Finally, on the largest scale (∼10 8 km) the solar wind speed ramps up from ∼400kms -1 to ∼750kms -1 , typical of polar hole flows. While it seems likely that the stream interface maps back to a sharp boundary near the Sun, the large region of increasing flow speed suggests that there is also an extended gradient in solar wind source speed close to the Sun. copyright 1998 American Geophysical Union

On the Thermodynamics of a Gas of AdS Black Holes and the Quark-Hadron Phase Transition

CERN Document Server

Ellis, Jonathan Richard; Mavromatos, Nikolaos E; Ellis, John

1999-01-01

We discuss the thermodynamics of a gas of black holes in five-dimensional anti-de-Sitter (AdS) space, showing that they are described by a van der Waals equation of state. Motivated by the Maldacena conjecture, we relate the energy density and pressure of this non-ideal AdS black-hole gas to those of four-dimensional gauge theory in the unconfined phase. We find that the energy density rises rapidly above the deconfinement transition temperature, whilst the pressure rises more slowly towards its asymptotic high-temperature value, in qualitative agreement with lattice simulations.

Reentrant phase transitions of higher-dimensional AdS black holes in dRGT massive gravity

International Nuclear Information System (INIS)

Zou, De-Cheng; Yue, Ruihong; Zhang, Ming

2017-01-01

We study the P-V criticality and phase transition in the extended phase space of anti-de Sitter (AdS) black holes in higher-dimensional de Rham, Gabadadze and Tolley (dRGT) massive gravity, treating the cosmological constant as pressure and the corresponding conjugate quantity is interpreted as thermodynamic volume. Besides the usual small/large black hole phase transitions, the interesting thermodynamic phenomena of reentrant phase transitions (RPTs) are observed for black holes in all d ≥ 6-dimensional spacetime when the coupling coefficients c_im"2 of massive potential satisfy some certain conditions. (orig.)

Evaluative pressure overcomes perceptual load effects.

Science.gov (United States)

Normand, Alice; Autin, Frédérique; Croizet, Jean-Claude

2015-06-01

Perceptual load has been found to be a powerful bottom-up determinant of distractibility, with high perceptual load preventing distraction by any irrelevant information. However, when under evaluative pressure, individuals exert top-down attentional control by giving greater weight to task-relevant features, making them more distractible from task-relevant distractors. One study tested whether the top-down modulation of attention under evaluative pressure overcomes the beneficial bottom-up effect of high perceptual load on distraction. Using a response-competition task, we replicated previous findings that high levels of perceptual load suppress task-relevant distractor response interference, but only for participants in a control condition. Participants under evaluative pressure (i.e., who believed their intelligence was assessed) showed interference from task-relevant distractor at all levels of perceptual load. This research challenges the assumptions of the perceptual load theory and sheds light on a neglected determinant of distractibility: the self-relevance of the performance situation in which attentional control is solicited.

Observation of Internal Photoinduced Electron and Hole Separation in Hybrid Two-Dimentional Perovskite Films.

Science.gov (United States)

Liu, Junxue; Leng, Jing; Wu, Kaifeng; Zhang, Jun; Jin, Shengye

2017-02-01

Two-dimensional (2D) organolead halide perovskites are promising for various optoelectronic applications. Here we report a unique spontaneous charge (electron/hole) separation property in multilayered (BA) 2 (MA) n-1 Pb n I 3n+1 (BA = CH 3 (CH 2 ) 3 NH 3 + , MA = CH 3 NH 3 + ) 2D perovskite films by studying the charge carrier dynamics using ultrafast transient absorption and photoluminescence spectroscopy. Surprisingly, the 2D perovskite films, although nominally prepared as "n = 4", are found to be mixture of multiple perovskite phases, with n = 2, 3, 4 and ≈ ∞, that naturally align in the order of n along the direction perpendicular to the substrate. Driven by the band alignment between 2D perovskites phases, we observe consecutive photoinduced electron transfer from small-n to large-n phases and hole transfer in the opposite direction on hundreds of picoseconds inside the 2D film of ∼358 nm thickness. This internal charge transfer efficiently separates electrons and holes to the upper and bottom surfaces of the films, which is a unique property beneficial for applications in photovoltaics and other optoelectronics devices.

New aspect of critical nonlinearly charged black hole

Science.gov (United States)

Hendi, S. H.; Taghadomi, Z. S.; Corda, C.

2018-04-01

The motion of a point charged particle moving in the background of the critical power Maxwell charged AdS black holes in a probe approximation is studied. The extended phase space, where the cosmological constant appears as a pressure, is regarded and the effective potential is investigated. At last, the mass-to-charge ratio and the large q limit are studied.

The Bottom Boundary Layer.

Science.gov (United States)

Trowbridge, John H; Lentz, Steven J

2018-01-03

The oceanic bottom boundary layer extracts energy and momentum from the overlying flow, mediates the fate of near-bottom substances, and generates bedforms that retard the flow and affect benthic processes. The bottom boundary layer is forced by winds, waves, tides, and buoyancy and is influenced by surface waves, internal waves, and stratification by heat, salt, and suspended sediments. This review focuses on the coastal ocean. The main points are that (a) classical turbulence concepts and modern turbulence parameterizations provide accurate representations of the structure and turbulent fluxes under conditions in which the underlying assumptions hold, (b) modern sensors and analyses enable high-quality direct or near-direct measurements of the turbulent fluxes and dissipation rates, and (c) the remaining challenges include the interaction of waves and currents with the erodible seabed, the impact of layer-scale two- and three-dimensional instabilities, and the role of the bottom boundary layer in shelf-slope exchange.

The Bottom Boundary Layer

Science.gov (United States)

Trowbridge, John H.; Lentz, Steven J.

2018-01-01

The oceanic bottom boundary layer extracts energy and momentum from the overlying flow, mediates the fate of near-bottom substances, and generates bedforms that retard the flow and affect benthic processes. The bottom boundary layer is forced by winds, waves, tides, and buoyancy and is influenced by surface waves, internal waves, and stratification by heat, salt, and suspended sediments. This review focuses on the coastal ocean. The main points are that (a) classical turbulence concepts and modern turbulence parameterizations provide accurate representations of the structure and turbulent fluxes under conditions in which the underlying assumptions hold, (b) modern sensors and analyses enable high-quality direct or near-direct measurements of the turbulent fluxes and dissipation rates, and (c) the remaining challenges include the interaction of waves and currents with the erodible seabed, the impact of layer-scale two- and three-dimensional instabilities, and the role of the bottom boundary layer in shelf-slope exchange.

Low-mass black holes as the remnants of primordial black hole formation.

Science.gov (United States)

Greene, Jenny E

2012-01-01

Bridging the gap between the approximately ten solar mass 'stellar mass' black holes and the 'supermassive' black holes of millions to billions of solar masses are the elusive 'intermediate-mass' black holes. Their discovery is key to understanding whether supermassive black holes can grow from stellar-mass black holes or whether a more exotic process accelerated their growth soon after the Big Bang. Currently, tentative evidence suggests that the progenitors of supermassive black holes were formed as ∼10(4)-10(5) M(⊙) black holes via the direct collapse of gas. Ongoing searches for intermediate-mass black holes at galaxy centres will help shed light on this formation mechanism.

Hole dephasing caused by hole-hole interaction in a multilayered black phosphorus.

Science.gov (United States)

Li, Lijun; Khan, Muhammad Atif; Lee, Yoontae; Lee, Inyeal; Yun, Sun Jin; Youn, Doo-Hyeb; Kim, Gil-Ho

2017-11-01

We study the magnetotransport of holes in a multilayered black phosphorus in a temperature range of 1.9 to 21.5 K. We observed a negative magnetoresistance at magnetic fields up to 1.5 T. This negative magetoresistance was analyzed by weak localization theory in diffusive regime. At the lowest temperature and the highest carrier density we found a phase coherence length of 48 nm. The linear temperature dependence of the dephasing rate shows that the hole-hole scattering processes with small energy transfer are the dominant contribution in breaking the carrier phase coherence.

Analysis of Peach Bottom turbine trip tests

International Nuclear Information System (INIS)

Cheng, H.S.; Lu, M.S.; Hsu, C.J.; Shier, W.G.; Diamond, D.J.; Levine, M.M.; Odar, F.

1979-01-01

Current interest in the analysis of turbine trip transients has been generated by the recent tests performed at the Peach Bottom (Unit 2) reactor. Three tests, simulating turbine trip transients, were performed at different initial power and coolant flow conditions. The data from these tests provide considerable information to aid qualification of computer codes that are currently used in BWR design analysis. The results are presented of an analysis of a turbine trip transient using the RELAP-3B and the BNL-TWIGL computer codes. Specific results are provided comparing the calculated reactor power and system pressures with the test data. Excellent agreement for all three test transients is evident from the comparisons

Bifurcation from stable holes to replicating holes in vibrated dense suspensions.

Science.gov (United States)

Ebata, H; Sano, M

2013-11-01

In vertically vibrated starch suspensions, we observe bifurcations from stable holes to replicating holes. Above a certain acceleration, finite-amplitude deformations of the vibrated surface continue to grow until void penetrates fluid layers, and a hole forms. We studied experimentally and theoretically the parameter dependence of the holes and their stabilities. In suspensions of small dispersed particles, the circular shapes of the holes are stable. However, we find that larger particles or lower surface tension of water destabilize the circular shapes; this indicates the importance of capillary forces acting on the dispersed particles. Around the critical acceleration for bifurcation, holes show intermittent large deformations as a precursor to hole replication. We applied a phenomenological model for deformable domains, which is used in reaction-diffusion systems. The model can explain the basic dynamics of the holes, such as intermittent behavior, probability distribution functions of deformation, and time intervals of replication. Results from the phenomenological model match the linear growth rate below criticality that was estimated from experimental data.

Early effects of water inflow into a deposition hole. Laboratory tests results

International Nuclear Information System (INIS)

Sanden, Torbjoern; Boergesson, Lennart

2010-12-01

During the installation of buffer and canister in a deposition hole a number of different problems can arise. The problems are mainly connected to water flow from fractures in the rock into the deposition hole. At some conditions it probably will be necessary to protect the installed buffer blocks with a special sheet made of rubber or plastic. This report deals with two processes that can occur and are possible to strongly influence the buffer during installation: 1. Erosion. Erosion of bentonite from the deposition hole up to the voids in the tunnel backfill. This process will continue until a tunnel plug have been built and the voids in the backfill are filled with water. 2. Heave. Early wetting of the pellets filling may cause a heave of the buffer blocks that will decrease the density of the buffer. An erosion model has been suggested /Sanden et al. 2008b/ which makes it possible to estimate the amount of eroded material for a certain water flow rate during a certain time. In order to verify the model and investigate how the buffer in a deposition hole behaves when exposed to a water flow, a number of different tests have been performed: - Test type 1. Simulation of water flow out from a deposition hole. The deposition hole was made of steel and had a radial scale of 1:4 and a height of 0.6 meter. The pellets slot was scaled 1:1. After filling the deposition hole with buffer blocks and pellets, a constant water flow was applied in a point at the bottom. The discharged water at the top was collected and the amount of eroded material determined. The displacement of the blocks and pellets surfaces was also measured during the test. - Test type 2. The influence of test length on the erosion rate was investigated by performing tests with Plexiglas tubes of different lengths (0.4 and 4 meter). The tubes were positioned vertically, filled with pellets and a point inflow was applied in the bottom. The discharged water was collected at the top and the amount of eroded

Early effects of water inflow into a deposition hole. Laboratory tests results

Energy Technology Data Exchange (ETDEWEB)

Sanden, Torbjoern; Boergesson, Lennart (Clay Technology AB, Lund (Sweden))

2010-12-15

During the installation of buffer and canister in a deposition hole a number of different problems can arise. The problems are mainly connected to water flow from fractures in the rock into the deposition hole. At some conditions it probably will be necessary to protect the installed buffer blocks with a special sheet made of rubber or plastic. This report deals with two processes that can occur and are possible to strongly influence the buffer during installation: 1. Erosion. Erosion of bentonite from the deposition hole up to the voids in the tunnel backfill. This process will continue until a tunnel plug have been built and the voids in the backfill are filled with water. 2. Heave. Early wetting of the pellets filling may cause a heave of the buffer blocks that will decrease the density of the buffer. An erosion model has been suggested /Sanden et al. 2008b/ which makes it possible to estimate the amount of eroded material for a certain water flow rate during a certain time. In order to verify the model and investigate how the buffer in a deposition hole behaves when exposed to a water flow, a number of different tests have been performed: - Test type 1. Simulation of water flow out from a deposition hole. The deposition hole was made of steel and had a radial scale of 1:4 and a height of 0.6 meter. The pellets slot was scaled 1:1. After filling the deposition hole with buffer blocks and pellets, a constant water flow was applied in a point at the bottom. The discharged water at the top was collected and the amount of eroded material determined. The displacement of the blocks and pellets surfaces was also measured during the test. - Test type 2. The influence of test length on the erosion rate was investigated by performing tests with Plexiglas tubes of different lengths (0.4 and 4 meter). The tubes were positioned vertically, filled with pellets and a point inflow was applied in the bottom. The discharged water was collected at the top and the amount of eroded

Investigations on effects of the hole size to fix electrodes and interconnection lines in polydimethylsiloxane

Science.gov (United States)

Behkami, Saber; Frounchi, Javad; Ghaderi Pakdel, Firouz; Stieglitz, Thomas

2017-11-01

Translational research in bioelectronics medicine and neural implants often relies on established material assemblies made of silicone rubber (polydimethylsiloxane-PDMS) and precious metals. Longevity of the compound is of utmost importance for implantable devices in therapeutic and rehabilitation applications. Therefore, secure mechanical fixation can be used in addition to chemical bonding mechanisms to interlock PDMS substrate and insulation layers with metal sheets for interconnection lines and electrodes. One of the best ways to fix metal lines and electrodes in PDMS is to design holes in electrode rims to allow for direct interconnection between top to bottom layer silicone. Hence, the best layouts and sizes of holes (up to 6) which provide sufficient stability against lateral and vertical forces have been investigated with a variety of numbers of hole in line electrodes, which are simulated and fabricated with different layouts, sizes and materials. Best stability was obtained with radii of 100, 72 and 62 µm, respectively, and a single central hole in aluminum, platinum and MP35N foil line electrodes of 400  ×  500 µm2 size and of thickness 20 µm. The study showed that the best hole size which provides line electrode immobility (of thickness less than 30 µm) within a central hole is proportional to reverse value of Young’s Modulus of the material used. Thus, an array of line electrodes was designed and fabricated to study this effect. Experimental results were compared with simulation data. Subsequently, an approximation curve was generated as design rule to propose the best radius to fix line electrodes according to the material thickness between 10 and 200 µm using PDMS as substrate material.

Drilling and the associated drillhole measurements of the pilot hole ONK-PH5

International Nuclear Information System (INIS)

Oehberg, A.; Hirvonen, H.; Jurvanen, T.; Kemppainen, K.; Mustonen, A.; Niemonen, J.; Poellaenen, J.; Rouhiainen, P.; Rautio, T.

2006-09-01

The construction of the ONKALO access tunnel started in September 2004 at Olkiluoto. Most of the investigations related to the construction of the access tunnel aim to ensure successful excavations, reinforcement and sealing. Pilot holes are drillholes, which are core drilled along the tunnel profile. The length of the pilot holes typically varies from several tens of metres to a couple of hundred metres. The pilot holes are aimed to confirm the quality of the rock mass for tunnel construction, and in particular to identify water conductive fractured zones and to provide information that could result in modifications of the existing construction plans. The pilot hole ONK-PH5 was drilled from chainage 991.4 to chainage 1194 in January 2006. The length of the hole is 202.64 m and the vertical depth of the hole from zero level is about 88.2-107.5 m. The aim during the drilling work was to orient core samples as much as possible. The deviation of the drillhole was measured during and after the drilling phase. One steering operation by wedging was made at the hole depth of 128.58 metres. Electric conductivity was measured from the collected returning water samples. Logging of the core samples included the following parameters: lithology, foliation, fracturing, fracture frequency, RQD, fractured zones, core loss and weathering. The rock mechanical logging was based on Q-classification. The tests to determine rock strength and deformation properties were made with a Rock Tester-equipment. Due to high inflow (c. 200 L/min) mainly from the depth section 56-58 metres no geophysical surveys were carried out in the hole. Flow logging was carried out only from 58 metres to the bottom of the hole. Difference Flow method was used for the determination of hydraulic conductivity in fractures and fractured zones in the drillhole. The overlapping i.e. the detailed flow logging mode was used. The flow logging was performed with 0.5 m section length and with 0.1 m depth increment. Flow

INTEGRATED DRILLING SYSTEM USING MUD ACTUATED DOWN HOLE HAMMER AS PRIMARY ENGINE

Energy Technology Data Exchange (ETDEWEB)

John V. Fernandez; David S. Pixton

2005-12-01

A history and project summary of the development of an integrated drilling system using a mud-actuated down-hole hammer as its primary engine are given. The summary includes laboratory test results, including atmospheric tests of component parts and simulated borehole tests of the hammer system. Several remaining technical hurdles are enumerated. A brief explanation of commercialization potential is included. The primary conclusion for this work is that a mud actuated hammer can yield substantial improvements to drilling rate in overbalanced, hard rock formations. A secondary conclusion is that the down-hole mud actuated hammer can serve to provide other useful down-hole functions including generation of high pressure mud jets, generation of seismic and sonic signals, and generation of diagnostic information based on hammer velocity profiles.

Water cooled static pressure probe

Science.gov (United States)

Lagen, Nicholas T. (Inventor); Eves, John W. (Inventor); Reece, Garland D. (Inventor); Geissinger, Steve L. (Inventor)

1991-01-01

An improved static pressure probe containing a water cooling mechanism is disclosed. This probe has a hollow interior containing a central coolant tube and multiple individual pressure measurement tubes connected to holes placed on the exterior. Coolant from the central tube symmetrically immerses the interior of the probe, allowing it to sustain high temperature (in the region of 2500 F) supersonic jet flow indefinitely, while still recording accurate pressure data. The coolant exits the probe body by way of a reservoir attached to the aft of the probe. The pressure measurement tubes are joined to a single, larger manifold in the reservoir. This manifold is attached to a pressure transducer that records the average static pressure.

Black Holes

OpenAIRE

Horowitz, Gary T.; Teukolsky, Saul A.

1998-01-01

Black holes are among the most intriguing objects in modern physics. Their influence ranges from powering quasars and other active galactic nuclei, to providing key insights into quantum gravity. We review the observational evidence for black holes, and briefly discuss some of their properties. We also describe some recent developments involving cosmic censorship and the statistical origin of black hole entropy.

Black hole levitron

International Nuclear Information System (INIS)

Arsiwalla, Xerxes D.; Verlinde, Erik P.

2010-01-01

We study the problem of spatially stabilizing four dimensional extremal black holes in background electric/magnetic fields. Whilst looking for stationary stable solutions describing black holes placed in external fields we find that taking a continuum limit of Denef et al.'s multicenter supersymmetric black hole solutions provides a supergravity description of such backgrounds within which a black hole can be trapped within a confined volume. This construction is realized by solving for a levitating black hole over a magnetic dipole base. We comment on how such a construction is akin to a mechanical levitron.

The implementation of the integrated design process in the hole-plan system

Directory of Open Access Journals (Sweden)

Won-Sun Ruy

2012-12-01

Full Text Available All current shipyards are using the customized CAD/CAM programs in order to improve the design quality and increase the design efficiency. Even though the data structures for ship design and construction are almost completed, the implementation related to the ship design processes are still in progress so that it has been the main causes of the bottleneck and delay during the middle of design process. In this study, we thought that the hole-plan system would be a good example which is remained to be improved. The people of outfitting division who don't have direct authority to edit the structural panels, should request the hull design division to install the holes for the outfitting equipment. For acceptance, they should calculate the hole position, determine the hole type, and find the intersected contour of panel. After consideration of the hull people, the requested holes are manually installed on the hull structure. As the above, many processes are needed such as communication and discussion between the divisions, drawings for hole-plan, and the consideration for the structural or production compatibility. However this iterative process takes a lot of working time and requires mental pressure to the related people and cross-division conflict. This paper will handle the hole-plan system in detail to automate the series of process and minimize the human efforts and time-consumption.

Reentrant phase transitions of higher-dimensional AdS black holes in dRGT massive gravity

Energy Technology Data Exchange (ETDEWEB)

Zou, De-Cheng; Yue, Ruihong [Yangzhou University, College of Physical Science and Technology, Yangzhou (China); Zhang, Ming [Xi' an Aeronautical University, Faculty of Science, Xi' an (China)

2017-04-15

We study the P-V criticality and phase transition in the extended phase space of anti-de Sitter (AdS) black holes in higher-dimensional de Rham, Gabadadze and Tolley (dRGT) massive gravity, treating the cosmological constant as pressure and the corresponding conjugate quantity is interpreted as thermodynamic volume. Besides the usual small/large black hole phase transitions, the interesting thermodynamic phenomena of reentrant phase transitions (RPTs) are observed for black holes in all d ≥ 6-dimensional spacetime when the coupling coefficients c{sub i}m{sup 2} of massive potential satisfy some certain conditions. (orig.)

Mass-induced sea level variations in the Red Sea from steric-corrected altimetry, GRACE, in-situ bottom pressure records, and hydrographic observations

Science.gov (United States)

Feng, Wei; Lemoine, Jean-Michel; Zhong, Min; Xu, Houze

2014-05-01

An annual amplitude of ~18 cm mass-induced sea level variations (SLV) in the Red Sea is detected from steric-corrected altimetry and the Gravity Recovery and Climate Experiment (GRACE) satellites from 2003 to 2011, which dominates the mean sea level in the region. Seawater mass variations here generally reach maximum in late January/early February. The steric component of SLV calculated from oceanographic temperature and salinity data is relatively small and peaks about seven months later than mass variations. The phase difference between the steric SLV and the mass-induced SLV indicates that when the Red Sea gains the mass from inflow water in winter, the steric SLV fall, and vice versa in summer. In-situ bottom pressure records in the eastern coast of the Red Sea validate the high mass variability observed by steric-corrected altimetry and GRACE. Furthermore, we compare the horizontal water mass flux in the Red Sea from steric-corrected altimetry and GRACE with that estimated from hydrographic observations.

Noncommutative black holes

Energy Technology Data Exchange (ETDEWEB)

Lopez-DomInguez, J C [Instituto de Fisica de la Universidad de Guanajuato PO Box E-143, 37150 Leoen Gto. (Mexico); Obregon, O [Instituto de Fisica de la Universidad de Guanajuato PO Box E-143, 37150 Leoen Gto. (Mexico); RamIrez, C [Facultad de Ciencias FIsico Matematicas, Universidad Autonoma de Puebla, PO Box 1364, 72000 Puebla (Mexico); Sabido, M [Instituto de Fisica de la Universidad de Guanajuato PO Box E-143, 37150 Leoen Gto. (Mexico)

2007-11-15

We study noncommutative black holes, by using a diffeomorphism between the Schwarzschild black hole and the Kantowski-Sachs cosmological model, which is generalized to noncommutative minisuperspace. Through the use of the Feynman-Hibbs procedure we are able to study the thermodynamics of the black hole, in particular, we calculate Hawking's temperature and entropy for the 'noncommutative' Schwarzschild black hole.

Black hole critical phenomena without black holes

Indian Academy of Sciences (India)

large values of Ф, black holes do form and for small values the scalar field ... on the near side of the ridge ultimately evolve to form black holes while those configu- ... The inset shows a bird's eye view looking down on the saddle point.

Search for black holes

International Nuclear Information System (INIS)

Cherepashchuk, Anatolii M

2003-01-01

Methods and results of searching for stellar mass black holes in binary systems and for supermassive black holes in galactic nuclei of different types are described. As of now (June 2002), a total of 100 black hole candidates are known. All the necessary conditions Einstein's General Relativity imposes on the observational properties of black holes are satisfied for candidate objects available, thus further assuring the existence of black holes in the Universe. Prospects for obtaining sufficient criteria for reliably distinguishing candidate black holes from real black holes are discussed. (reviews of topical problems)

EDDINGTON-LIMITED ACCRETION AND THE BLACK HOLE MASS FUNCTION AT REDSHIFT 6

International Nuclear Information System (INIS)

Willott, Chris J.; Crampton, David; Hutchings, John B.; Schade, David; Albert, Loic; Arzoumanian, Doris; Bergeron, Jacqueline; Omont, Alain; Delorme, Philippe; Reyle, Celine

2010-01-01

We present discovery observations of a quasar in the Canada-France High-z Quasar Survey (CFHQS) at redshift z = 6.44. We also use near-infrared spectroscopy of nine CFHQS quasars at z ∼ 6 to determine black hole masses. These are compared with similar estimates for more luminous Sloan Digital Sky Survey quasars to investigate the relationship between black hole mass and quasar luminosity. We find a strong correlation between Mg II FWHM and UV luminosity and that most quasars at this early epoch are accreting close to the Eddington limit. Thus, these quasars appear to be in an early stage of their life cycle where they are building up their black hole mass exponentially. Combining these results with the quasar luminosity function, we derive the black hole mass function at z = 6. Our black hole mass function is ∼10 4 times lower than at z = 0 and substantially below estimates from previous studies. The main uncertainties which could increase the black hole mass function are a larger population of obscured quasars at high redshift than is observed at low redshift and/or a low quasar duty cycle at z = 6. In comparison, the global stellar mass function is only ∼10 2 times lower at z = 6 than at z = 0. The difference between the black hole and stellar mass function evolution is due to either rapid early star formation which is not limited by radiation pressure as is the case for black hole growth or inefficient black hole seeding. Our work predicts that the black hole mass-stellar mass relation for a volume-limited sample of galaxies declines rapidly at very high redshift. This is in contrast to the observed increase at 4 < z < 6 from the local relation if one just studies the most massive black holes.

Rupture tests with reactor pressure vessel head models

International Nuclear Information System (INIS)

Talja, H.; Keinaenen, H.; Hosio, E.; Pankakoski, P.H.; Rahka, K.

2003-01-01

In the LISSAC project (LImit Strains in Severe ACcidents), partly funded by the EC Nuclear Fission and Safety Programme within the 5th Framework programme, an extensive experimental and computational research programme is conducted to study the stress state and size dependence of ultimate failure strains. The results are aimed especially to make the assessment of severe accident cases more realistic. For the experiments in the LISSAC project a block of material of the German Biblis C reactor pressure vessel was available. As part of the project, eight reactor pressure vessel head models from this material (22 NiMoCr 3 7) were tested up to rupture at VTT. The specimens were provided by Forschungszentrum Karlsruhe (FzK). These tests were performed under quasistatic pressure load at room temperature. Two specimens sizes were tested and in half of the tests the specimens contain holes describing the control rod penetrations of an actual reactor pressure vessel head. These specimens were equipped with an aluminium liner. All six tests with the smaller specimen size were conducted successfully. In the test with the large specimen with holes, the behaviour of the aluminium liner material proved to differ from those of the smaller ones. As a consequence the experiment ended at the failure of the liner. The specimen without holes yielded results that were in very good agreement with those from the small specimens. (author)

Characteristics of via-hole interconnections fabricated by using an inkjet printing method

International Nuclear Information System (INIS)

Yang, Yong Suk; You, In Kyu; Koo, Jae Bon; Lee, Sang Seok; Lim, Sang Chul; Kang, Seong Youl; Noh, Yong Young

2010-01-01

Inkjet printing is a familiar technique that creates and releases droplets of fluid on demand and precisely deposits those droplets on a substrate. It has received increased attention for its novelty and ability to produce patterned and template material structures. In the application of electronic interconnection fabrication, drop-on-demand inkjet printers especially offer the advantages of contactless printing and eliminat the use of a die or photomask. In this study, we created a via-hole interconnecting structure through a polymer insulator layer by using an inkjet printing. When the droplets of Ag ink were dropped onto a PMMA/Au/Cr/SiO 2 /Si area and the Ag film was annealed at high temperatures, the Ag ink containing solvents penetrated into the PMMA layer and generated the conducting paths between the top Ag and the bottom Au electrodes by partial dissolution and swelling of the polymer. The surface and the cross-sectional topologies of the formed via-holes were investigated by using an optical microscope and a field emission transmission electron microscope.

Violin f-hole contribution to far-field radiation via patch near-field acoustical holography.

Science.gov (United States)

Bissinger, George; Williams, Earl G; Valdivia, Nicolas

2007-06-01

The violin radiates either from dual ports (f-holes) or via surface motion of the corpus (top+ribs+back), with no clear delineation between these sources. Combining "patch" near-field acoustical holography over just the f-hole region of a violin with far-field radiativity measurements over a sphere, it was possible to separate f-hole from surface motion contributions to the total radiation of the corpus below 2.6 kHz. A0, the Helmholtz-like lowest cavity resonance, radiated essentially entirely through the f-holes as expected while A1, the first longitudinal cavity mode with a node at the f-holes, had no significant f-hole radiation. The observed A1 radiation comes from an indirect radiation mechanism, induced corpus motion approximately mirroring the cavity pressure profile seen for violinlike bowed string instruments across a wide range of sizes. The first estimates of the fraction of radiation from the f-holes F(f) indicate that some low frequency corpus modes thought to radiate only via surface motion (notably the first corpus bending modes) had significant radiation through the f-holes, in agreement with net volume changes estimated from experimental modal analysis. F(f) generally trended lower with increasing frequency, following corpus mobility decreases. The f-hole directivity (top/back radiativity ratio) was generally higher than whole-violin directivity.

Effect of Matrix-Wellbore Flow and Porosity on Pressure Transient Response in Shale Formation Modeling by Dual Porosity and Dual Permeability System

Directory of Open Access Journals (Sweden)

Daolun Li

2015-01-01

Full Text Available A mathematical dual porosity and dual permeability numerical model based on perpendicular bisection (PEBI grid is developed to describe gas flow behaviors in shale-gas reservoirs by incorporating slippage corrected permeability and adsorbed gas effect. Parametric studies are conducted for a horizontal well with multiple infinite conductivity hydraulic fractures in shale-gas reservoir to investigate effect of matrix-wellbore flow, natural fracture porosity, and matrix porosity. We find that the ratio of fracture permeability to matrix permeability approximately decides the bottom hole pressure (BHP error caused by omitting the flow between matrix and wellbore and that the effect of matrix porosity on BHP is related to adsorption gas content. When adsorbed gas accounts for large proportion of the total gas storage in shale formation, matrix porosity only has a very small effect on BHP. Otherwise, it has obvious influence. This paper can help us understand the complex pressure transient response due to existence of the adsorbed gas and help petroleum engineers to interpret the field data better.

Small Engines as Bottoming Cycle Steam Expanders for Internal Combustion Engines

Directory of Open Access Journals (Sweden)

Rohitha Weerasinghe

2017-01-01

Full Text Available Heat recovery bottoming cycles for internal combustion engines have opened new avenues for research into small steam expanders (Stobart and Weerasinghe, 2006. Dependable data for small steam expanders will allow us to predict their suitability as bottoming cycle engines and the fuel economy achieved by using them as bottoming cycles. Present paper is based on results of experiments carried out on small scale Wankel and two-stroke reciprocating engines as air expanders and as steam expanders. A test facility developed at Sussex used for measurements is comprised of a torque, power and speed measurements, electronic actuation of valves, synchronized data acquisition of pressure, and temperatures of steam and inside of the engines for steam and internal combustion cycles. Results are presented for four engine modes, namely, reciprocating engine in uniflow steam expansion mode and air expansion mode and rotary Wankel engine in steam expansion mode and air expansion mode. The air tests will provide base data for friction and motoring effects whereas steam tests will tell how effective the engines will be in this mode. Results for power, torque, and p-V diagrams are compared to determine the change in performance from air expansion mode to steam expansion mode.

Root-Contact/Pressure-Plate Assembly For Hydroponic System

Science.gov (United States)

Morris, Carlton E.; Loretan, Philip A.; Bonsi, Conrad K.; Hill, Walter A.

1994-01-01

Hydroponic system includes growth channels equipped with rootcontact/pressure-plate assemblies. Pump and associated plumbing circulate nutrient liquid from reservoir, along bottom of growth channels, and back to reservoir. Root-contact/pressure-plate assembly in each growth channel stimulates growth of roots by applying mild contact pressure. Flat plate and plate connectors, together constitute pressure plate, free to move upward to accommodate growth of roots. System used for growing sweetpotatoes and possibly other tuber and root crops.

Temperature effects on the geometry during the formation of micro-holes fabricated by femtosecond laser in PMMA

Science.gov (United States)

Zhang, Fan; Dong, Xinran; Yin, Kai; Song, Yuxin; Tian, Yaxiang; Wang, Cong; Duan, Ji'an

2018-03-01

In this study, the temperature effects on hole geometry of the PMMA during micro-holes drilling by femtosecond laser has been studied under various pulse energy and number of pulse. The laser-induced hole's diameter is considerably increased by 73% as the temperature rises from 20 °C to 90 °C. Remarkable enhancement in the removal volume of micro-hole is also observed under high temperature. The possible mechanism for such changes is discussed in detail on account of optical absorption enhancement and higher density of surface plasma. The atomic percentage of oxygen obviously increases with the increase of temperature, which is beneficial to femtosecond laser fabrication of PMMA micro-hole. The spatter area of micro-hole has been found to tremendously extend with the increase of temperature, which is due to recoil pressure effect. These results demonstrate that temperature plays a crucial role to tailor micro-hole fabrication by femtosecond laser.

Geometrical thermodynamics and P-V criticality of the black holes with power-law Maxwell field

Energy Technology Data Exchange (ETDEWEB)

Hendi, S.H.; Panah, B.E. [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of); Research Institute for Astronomy and Astrophysics of Maragha (RIAAM), Maragha (Iran, Islamic Republic of); Panahiyan, S. [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of); Shahid Beheshti University, Physics Department, Tehran (Iran, Islamic Republic of); Talezadeh, M.S. [Shiraz University, Physics Department and Biruni Observatory, College of Sciences, Shiraz (Iran, Islamic Republic of)

2017-02-15

We study the thermodynamical structure of Einstein black holes in the presence of power Maxwell invariant nonlinear electrodynamics for two different cases. The behavior of temperature and conditions regarding the stability of these black holes are investigated. Since the language of geometry is an effective method in general relativity, we concentrate on the geometrical thermodynamics to build a phase space for studying thermodynamical properties of these black holes. In addition, taking into account the denominator of the heat capacity, we use the proportionality between cosmological constant and thermodynamical pressure to extract the critical values for these black holes. Besides, the effects of the variation of different parameters on the thermodynamical structure of these black holes are investigated. Furthermore, some thermodynamical properties such as the volume expansion coefficient, speed of sound, and isothermal compressibility coefficient are calculated and some remarks regarding these quantities are given. (orig.)

Geometrical thermodynamics and P-V criticality of the black holes with power-law Maxwell field

International Nuclear Information System (INIS)

Hendi, S.H.; Panah, B.E.; Panahiyan, S.; Talezadeh, M.S.

2017-01-01

We study the thermodynamical structure of Einstein black holes in the presence of power Maxwell invariant nonlinear electrodynamics for two different cases. The behavior of temperature and conditions regarding the stability of these black holes are investigated. Since the language of geometry is an effective method in general relativity, we concentrate on the geometrical thermodynamics to build a phase space for studying thermodynamical properties of these black holes. In addition, taking into account the denominator of the heat capacity, we use the proportionality between cosmological constant and thermodynamical pressure to extract the critical values for these black holes. Besides, the effects of the variation of different parameters on the thermodynamical structure of these black holes are investigated. Furthermore, some thermodynamical properties such as the volume expansion coefficient, speed of sound, and isothermal compressibility coefficient are calculated and some remarks regarding these quantities are given. (orig.)

A Dancing Black Hole

Science.gov (United States)

Shoemaker, Deirdre; Smith, Kenneth; Schnetter, Erik; Fiske, David; Laguna, Pablo; Pullin, Jorge

2002-04-01

Recently, stationary black holes have been successfully simulated for up to times of approximately 600-1000M, where M is the mass of the black hole. Considering that the expected burst of gravitational radiation from a binary black hole merger would last approximately 200-500M, black hole codes are approaching the point where simulations of mergers may be feasible. We will present two types of simulations of single black holes obtained with a code based on the Baumgarte-Shapiro-Shibata-Nakamura formulation of the Einstein evolution equations. One type of simulations addresses the stability properties of stationary black hole evolutions. The second type of simulations demonstrates the ability of our code to move a black hole through the computational domain. This is accomplished by shifting the stationary black hole solution to a coordinate system in which the location of the black hole is time dependent.

XFEM Modelling of Multi-holes Plate with Single-row and Staggered Holes Configurations

Directory of Open Access Journals (Sweden)

Supar Khairi

2017-01-01

Full Text Available Joint efficiency is the key to composite structures assembly design, good structures response is dependent upon multi-holes behavior as subjected to remote loading. Current benchmarking work were following experimental testing series taken from literature on multi-holes problem. Eleven multi-hole configurations were investigated with various pitch and gage distance of staggered holes and non-staggered holes (single-row holes. Various failure modes were exhibited, most staggered holes demonstrates staggered crack path but non-staggered holes series displayed crack path along net-section plane. Stress distribution were carried out and good agreement were exhibited in experimental observation as reported in the respective literature. Consequently, strength prediction work were carried out under quasi-static loading, most showed discrepancy between 8% -31%, better prediction were exhibited in thicker and non-staggered holes plate combinations.

Process for opening up carboniferous seams for underground gasification by drilling production holes downwards

Energy Technology Data Exchange (ETDEWEB)

Lokschin, J L; Volk, A F; Starinskii, A A

1977-12-01

This process will reduce drilling costs and times by 20 to 25% and will improve gasification under the influence of a thin liquid medium connecting adjacent holes. After determining the approximate depth and thickness of the seam to be opened up, e.g. by geological means, production holes of 100 to 400 mm (diameter) are made down to a depth of 400 m or more, by well-known boring bars and chisels. After passing the top of the seam (the roof of the seam), which can be recognised by discoloration of the drilling liquid, one goes 1/2 to 1 metre deeper and one determines the depth of the roof the seam exactly by the reduced natural radioactivity at the boundary layer, by introducing a gamma sensor on to the boring bar. The production holes are taken down in a second borehold to a free space 0.6 to 2 metres above the floor of the seam (bottom of the seam), according to the thickness of the seam. After replacing the boring bar by a feedpipe one continues to drill using a boring bar of smaller cutting diameter inside this tube. This hole reaches from the foot of the pipe of the feedpipe to the floor of the seam. It is preferably flushed with gas but may be flushed with liquid. A thin liquid introduced into this hole penetrates the surrounding mass of the seam horizontally (unhindered by any armouring) and represents the required connection to neighbouring bores for gasification. The process is suitable for mining coal, combustible shale oil, bituminous rock, heavy natural oil where this process is based on gasification, melting or dissolving of those deposits.

Cavitation nuclei in water exposed to transient pressures

DEFF Research Database (Denmark)

Andersen, Anders Peter; Mørch, Knud Aage

2015-01-01

A model of skin-stabilized interfacial cavitation nuclei and their response to tensile and compressive stressing is presented. The model is evaluated in relation to experimental tensile strength results for water at rest at the bottom of an open water-filled container at atmospheric pressure...... and room temperature. These results are obtained by recording the initial growth of cavities generated by a short tensile pulse applied to the bottom of the container. It is found that the cavitation nuclei shift their tensile strength depending on their pressure history. Static pressurization...... for an extended period of time prior to testing is known to increase the tensile strength of water, but little information is available on how it is affected by compression pulses of short duration. This is addressed by imposing compression pulses of approximately 1 ms duration and a peak intensity of a few bar...

Direct injection of high pressure gas : scaling properties of pulsed turbulent jets

NARCIS (Netherlands)

Baert, R.S.G.; Klaassen, A.; Doosje, E.

2010-01-01

Existing gasoline DI injection equipment has been modified to generate single hole pulsed gas jets. Injection experiments have been performed at combinations of 3 different pressure ratios (2 of which supercritical) respectively 3 different hole geometries (i.e. length to diameter ratios). Injection

Study on collapse behavior of a square plate subjected to water pressure; Suiatsu wo ukeru kukeiban no atsukai kyodo ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Yao, T; Fujikubo, M; Mizutani, K [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

1996-04-10

Bottom plates of a hull are subjected to laterally distributing force due to in-plane compression force and water pressure in the ship`s length direction as a result of longitudinal bending in a hogging condition. Because buckling collapse of the hull bottom plates leads directly to longitudinal bending collapse of the hull bottom cross section, the hull bottom plates must have sufficient strength. The present study performs a static elastic large deflection analysis and an elasto-plastic large deflection analysis. It elucidates buckling collapse behavior of a square plate subjected to water pressure and in-plane compression load, and considers limits in application of conventional approximation analysis methods. In the case of a water pressure action, deflection components growing in excess of the buckling load do not necessarily correspond to buckling modes of the case where no water pressure is acting upon. Conventional approximation analysis methods may not be able often to pursue actual buckling phenomena. According the result of an analysis on hull bottom panels of an actual ship, the ultimate strength decreases when the water pressure is large. Compression force in the lateral direction as a result of water pressure acting on ship`s sides affected very little the ultimate strength. 3 refs., 7 figs.

Black holes will break up solitons and white holes may destroy them

International Nuclear Information System (INIS)

Akbar, Fiki T.; Gunara, Bobby E.; Susanto, Hadi

2017-01-01

Highlights: • What happens if a soliton collides with a black or white hole? • Solitons can pass through black hole horizons, but they will break up into several solitons after the collision. • In the interaction with a white hole horizon, solitons either pass through the horizon or will be destroyed by it. - Abstract: We consider a quantum analogue of black holes and white holes using Bose–Einstein condensates. The model is described by the nonlinear Schrödinger equation with a ‘stream flow’ potential, that induces a spatial translation to standing waves. We then mainly consider the dynamics of dark solitons in a black hole or white hole flow analogue and their interactions with the event horizon. A reduced equation describing the position of the dark solitons was obtained using variational method. Through numerical computations and comparisons with the analytical approximation we show that solitons can pass through black hole horizons even though they will break up into several solitons after the collision. In the interaction with a white hole horizon, we show that solitons either pass through the horizon or will be destroyed by it.

Black holes will break up solitons and white holes may destroy them

Energy Technology Data Exchange (ETDEWEB)

Akbar, Fiki T., E-mail: ftakbar@fi.itb.ac.id [Theoretical Physics Laboratory, Theoretical High Energy Physics and Instrumentation Research Group, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Jl. Ganesha no. 10, Bandung, 40132 (Indonesia); Gunara, Bobby E., E-mail: bobby@fi.itb.ac.id [Theoretical Physics Laboratory, Theoretical High Energy Physics and Instrumentation Research Group, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung, Jl. Ganesha no. 10, Bandung, 40132 (Indonesia); Susanto, Hadi, E-mail: hsusanto@essex.ac.uk [Department of Mathematical Sciences, University of Essex, Colchester, CO4 3SQ (United Kingdom)

2017-06-15

Highlights: • What happens if a soliton collides with a black or white hole? • Solitons can pass through black hole horizons, but they will break up into several solitons after the collision. • In the interaction with a white hole horizon, solitons either pass through the horizon or will be destroyed by it. - Abstract: We consider a quantum analogue of black holes and white holes using Bose–Einstein condensates. The model is described by the nonlinear Schrödinger equation with a ‘stream flow’ potential, that induces a spatial translation to standing waves. We then mainly consider the dynamics of dark solitons in a black hole or white hole flow analogue and their interactions with the event horizon. A reduced equation describing the position of the dark solitons was obtained using variational method. Through numerical computations and comparisons with the analytical approximation we show that solitons can pass through black hole horizons even though they will break up into several solitons after the collision. In the interaction with a white hole horizon, we show that solitons either pass through the horizon or will be destroyed by it.

Caged black holes: Black holes in compactified spacetimes. I. Theory

International Nuclear Information System (INIS)

Kol, Barak; Sorkin, Evgeny; Piran, Tsvi

2004-01-01

In backgrounds with compact dimensions there may exist several phases of black objects including a black hole and a black string. The phase transition between them raises questions and touches on fundamental issues such as topology change, uniqueness, and cosmic censorship. No analytic solution is known for the black hole, and moreover one can expect approximate solutions only for very small black holes, while phase transition physics happens when the black hole is large. Hence we turn to numerical solutions. Here some theoretical background to the numerical analysis is given, while the results will appear in a subsequent paper. The goals for a numerical analysis are set. The scalar charge and tension along the compact dimension are defined and used as improved order parameters which put both the black hole and the black string at finite values on the phase diagram. The predictions for small black holes are presented. The differential and the integrated forms of the first law are derived, and the latter (Smarr's formula) can be used to estimate the 'overall numerical error'. Field asymptotics and expressions for physical quantities in terms of the numerical values are supplied. The techniques include the 'method of equivalent charges', free energy, dimensional reduction, and analytic perturbation for small black holes

Alternate Explosions: Collapse and Accretion Events with Red Holes instead of Black Holes

OpenAIRE

Graber, James S.

1999-01-01

A red hole is "just like a black hole" except it lacks an event horizon and a singularity. As a result, a red hole emits much more energy than a black hole during a collapse or accretion event. We consider how a red hole solution can solve the "energy crisis" and power extremely energetic gamma ray bursts and hypernovae.

Airfoil, platform, and cooling passage measurements on a rotating transonic high-pressure turbine

Science.gov (United States)

Nickol, Jeremy B.

An experiment was performed at The Ohio State University Gas Turbine Laboratory for a film-cooled high-pressure turbine stage operating at design-corrected conditions, with variable rotor and aft purge cooling flow rates. Several distinct experimental programs are combined into one experiment and their results are presented. Pressure and temperature measurements in the internal cooling passages that feed the airfoil film cooling are used as boundary conditions in a model that calculates cooling flow rates and blowing ratio out of each individual film cooling hole. The cooling holes on the suction side choke at even the lowest levels of film cooling, ejecting more than twice the coolant as the holes on the pressure side. However, the blowing ratios are very close due to the freestream massflux on the suction side also being almost twice as great. The highest local blowing ratios actually occur close to the airfoil stagnation point as a result of the low freestream massflux conditions. The choking of suction side cooling holes also results in the majority of any additional coolant added to the blade flowing out through the leading edge and pressure side rows. A second focus of this dissertation is the heat transfer on the rotor airfoil, which features uncooled blades and blades with three different shapes of film cooling hole: cylindrical, diffusing fan shape, and a new advanced shape. Shaped cooling holes have previously shown immense promise on simpler geometries, but experimental results for a rotating turbine have not previously been published in the open literature. Significant improvement from the uncooled case is observed for all shapes of cooling holes, but the improvement from the round to more advanced shapes is seen to be relatively minor. The reduction in relative effectiveness is likely due to the engine-representative secondary flow field interfering with the cooling flow mechanics in the freestream, and may also be caused by shocks and other

Black and white holes

International Nuclear Information System (INIS)

Zeldovich, Ya.; Novikov, I.; Starobinskij, A.

1978-01-01

The theory is explained of the origination of white holes as a dual phenomenon with regard to the formation of black holes. Theoretically it is possible to derive the white hole by changing the sign of time in solving the general theory of relativity equation implying the black hole. The white hole represents the amount of particles formed in the vicinity of a singularity. For a distant observer, matter composed of these particles expands and the outer boundaries of this matter approach from the inside the gravitational radius Rsub(r). At t>>Rsub(r)/c all radiation or expulsion of matter terminates. For the outside observer the white hole exists for an unlimited length of time. In fact, however, it acquires the properties of a black hole and all processes in it cease. The qualitative difference between a white hole and a black hole is in that a white hole is formed as the result of an inner quantum explosion from the singularity to the gravitational radius and not as the result of a gravitational collapse, i.e., the shrinkage of diluted matter towards the gravitational radius. (J.B.)

Black and white holes

Energy Technology Data Exchange (ETDEWEB)

Zeldovich, Ya; Novikov, I; Starobinskii, A

1978-07-01

The theory is explained of the origination of white holes as a dual phenomenon with regard to the formation of black holes. Theoretically it is possible to derive the white hole by changing the sign of time in solving the general theory of relativity equation implying the black hole. The white hole represents the amount of particles formed in the vicinity of a singularity. For a distant observer, matter composed of these particles expands and the outer boundaries of this matter approach from the inside the gravitational radius R/sub r/. At t>>R/sub r//c all radiation or expulsion of matter terminates. For the outside observer the white hole exists for an unlimited length of time. In fact, however, it acquires the properties of a black hole and all processes in it cease. The qualitative difference between a white hole and a black hole is in that a white hole is formed as the result of an inner quantum explosion from the singularity to the gravitational radius and not as the result of a gravitational collapse, i.e., the shrinkage of diluted matter towards the gravitational radius.

Thin-shell wormholes from the regular Hayward black hole

Energy Technology Data Exchange (ETDEWEB)

Halilsoy, M.; Ovgun, A.; Mazharimousavi, S.H. [Eastern Mediterranean University, Department of Physics, Mersin 10 (Turkey)

2014-03-15

We revisit the regular black hole found by Hayward in 4-dimensional static, spherically symmetric spacetime. To find a possible source for such a spacetime we resort to the nonlinear electrodynamics in general relativity. It is found that a magnetic field within this context gives rise to the regular Hayward black hole. By employing such a regular black hole we construct a thin-shell wormhole for the case of various equations of state on the shell. We abbreviate a general equation of state by p = ψ(σ) where p is the surface pressure which is a function of the mass density (σ). In particular, linear, logarithmic, Chaplygin, etc. forms of equations of state are considered. In each case we study the stability of the thin shell against linear perturbations.We plot the stability regions by tuning the parameters of the theory. It is observed that the role of the Hayward parameter is to make the TSW more stable. Perturbations of the throat with small velocity condition are also studied. The matter of our TSWs, however, remains exotic. (orig.)

The effect of balance holes to centrifugal pump performance

Science.gov (United States)

Babayigit, O.; Ozgoren, M.; Aksoy, M. H.; Kocaaslan, O.

2017-07-01

The aim of this study is to analyze of a centrifugal pump with and without balance holes by using ANSYS-Fluent software. The pump used in the study is a commercial centrifugal pump consisting of two stages that is a model of Sempa Pump Company. Firstly, models of impeller, diffuser, suction and discharge sections of the centrifugal pump were separately drawn using Ansys and Solidworks software. Later, grid structures were generated on the flow volume of the pump. Turbulent flow volume was numerically solved by realizable k-є turbulence model. The flow analyses were focused on the centrifugal pump performance and the flow characteristics under different operational conditions with/without balance holes. Distributions of flow characteristics such as velocity and pressure distributions in the flow volume were also determined, numerically. The results of Computational Fluid Dynamics (CFD) with/without balance holes for the pump head and hydraulic efficiency on the design flow rate of 80 m3/h were found to be 81.5/91.3 m and 51.9/65.3%, respectively.

Bottom trawling affects fish condition through changes in the ratio of prey availability to density of competitors

DEFF Research Database (Denmark)

Hiddink, Jan Geert; Moranta, Joan; Balestrini, Stephen

2016-01-01

pressure. 2. We assessed the impact of bottom trawling on the food availability, condition and stomach contents of three flatfishes and the Norway lobster in an area in the Kattegat hat is characterized by a steep commercial bottom-trawling gradient due to the establishment of an area closed to all....... This pattern was mirrored in both the condition and stomach contents of plaice and for long-rough dab. 4. No effect of trawling on dab prey and condition was found. Conversely, the condition of the main target species – Norway lobster – increased as its biomass decreased with increased trawling intensities. 5...

Astrophysical black holes

CERN Document Server

Gorini, Vittorio; Moschella, Ugo; Treves, Aldo; Colpi, Monica

2016-01-01

Based on graduate school lectures in contemporary relativity and gravitational physics, this book gives a complete and unified picture of the present status of theoretical and observational properties of astrophysical black holes. The chapters are written by internationally recognized specialists. They cover general theoretical aspects of black hole astrophysics, the theory of accretion and ejection of gas and jets, stellar-sized black holes observed in the Milky Way, the formation and evolution of supermassive black holes in galactic centers and quasars as well as their influence on the dynamics in galactic nuclei. The final chapter addresses analytical relativity of black holes supporting theoretical understanding of the coalescence of black holes as well as being of great relevance in identifying gravitational wave signals. With its introductory chapters the book is aimed at advanced graduate and post-graduate students, but it will also be useful for specialists.

Model with Peach Bottom Turbine trip and thermal-Hydraulic code TRACE V5P3

International Nuclear Information System (INIS)

Mesado, C.; Miro, R.; Barrachina, T.; Verdu, G.

2014-01-01

This work is the continuation of the work presented previously in the thirty-ninth meeting annual of the Spanish Nuclear society. The semi-automatic translation of the Thermo-hydraulic model TRAC-BF1 Peach Bottom Turbine Trip to TRACE was presented in such work. This article is intended to validate the model obtained in TRACE, why compare the model results result from the translation with the Benchmark results: NEA/OECD BWR Peach Bottom Turbine Trip (PBTT), in particular is of the extreme scenario 2 of exercise 3, in which there is SCRAM in the reactor. Among other data present in the (transitional) Benchmark , are: total power, axial profile of power, pressure Dome, total reactivity and its components. (Author)

Pressurized water reactor with a reactor pressure vessel

International Nuclear Information System (INIS)

Werres, L.

1979-01-01

The core barrel is suspended from a flange by means of a grid. The coolant enters the barrel from below through the grid. In order to get a uniform flow over the reactor core there is provided for a guiding device below the grid. It consists of a cylindrical shell with borings uniformly distributed around the shell as well as fins on the inner surface of the shell and slots at the bottom facing the pressure vessel. (GL) [de

Experimental investigation of the Rowe's dilatancy law on an atypical granular medium from a municipal solid waste incineration bottom ash

Science.gov (United States)

Becquart, Frédéric; Abriak, Nor Edine

2013-06-01

Municipal Solid Waste Incineration (MSWI) bottom ashes are irregular granular media because of their origin and are very heterogeneous with a large quantity of angular particles of different chemical species. MSWI bottom ash is a renewable granular resource alternative to the use of non-renewable standard granular materials. Beneficial use of these alternative granular materials mainly lies in road engineering. However, the studies about mechanical properties of such granular media still remain little developed, those being mainly based on empirical considerations. In this paper, a study of mechanical behaviour of a MSWI bottom ash under axisymmetric triaxial loadings conditions is presented. Samples are initially dense after Proctor compaction, are saturated and tested in drained conditions, under different effective confining pressures ranging from 100 to 600 kPa. The evolutions of volumetric strains show an initial contracting phase followed by a dilatancy phase, more pronounced when the confining pressure is low. The stresses ratios at the characteristic state and at the critical state appear in good agreement and with a null rate of volume variation. The angles of internal friction and dilatancy of the studied MSWI bottom ash are estimated and are similar to conventional granular materials used especially in road engineering. The dilatancy law of Rowe is well experimentally verified on this irregular recycled granular material.

The effect of nuclear gas distribution on the mass determination of supermassive black holes

Science.gov (United States)

Mejía-Restrepo, J. E.; Lira, P.; Netzer, H.; Trakhtenbrot, B.; Capellupo, D. M.

2018-01-01

Supermassive black holes reside in the nuclei of most galaxies. During their active episodes, black holes are powered by accretion discs where gravitational energy is converted into radiation1. Accurately determining black hole masses is key to understand how the population evolves over time and how the black holes relate to their host galaxies2-4. Beyond the local universe, z ≳ 0.2, the mass is commonly estimated assuming a virialized motion of gas in the close vicinity of the active black holes, traced through broad emission lines5,6. However, this procedure has uncertainties associated with the unknown distribution of the gas clouds. Here, we show that the black hole masses derived from the properties of the accretion disk and virial mass estimates differ by a factor that is inversely proportional to the width of the broad emission lines. This leads to virial mass misestimations up to a factor of six. Our results suggest that a planar gas distribution that is inclined with respect to the line of sight may account for this effect. However, radiation pressure effects on the distribution of gas can also reproduce our results. Regardless of the physical origin, our findings contribute to mitigating the uncertainties in current black hole mass estimations and, in turn, will help us to better understand the evolution of distant supermassive black holes and their host galaxies.

Infusion of the solid coal using pressure independent valves to regulate flow

Energy Technology Data Exchange (ETDEWEB)

Goretz, H G; Betting, K

1979-01-01

In order to improve infusion into the solid coal, attempts were made to effect this through several holes using a single pump; however, the regulation of the quantity of water directed into each hole by a ball-valve tap connected to the injection pump was shown to lack precision - gives the causes of this defect. Satisfactory regulation was obtained by means of pressure- independent flow valves which operate on the principle of hydrodynamic pressure balance; describes method of operation. Underground tests proved satisfactory even with large pressure variations. The problem of dirt penetration during down times was eliminated by installing a check valve. The system proves economical to run.

Exact braneworld cosmology induced from bulk black holes

International Nuclear Information System (INIS)

Gregory, James P; Padilla, Antonio

2002-01-01

We use a new, exact approach in calculating the energy density measured by an observer living on a brane embedded in a charged black-hole spacetime. We find that the bulk Weyl tensor gives rise to nonlinear terms in the energy density and pressure in the FRW equations for the brane. Remarkably, these take exactly the same form as the 'unconventional' terms found in the cosmology of branes embedded in pure AdS, with extra matter living on the brane. Black-hole-driven cosmologies have the benefit that there is no ambiguity in splitting the braneworld energy momentum into tension and additional matter. We propose a new, enlarged relationship between the two descriptions of braneworld cosmology. We also study the exact thermodynamics of the field theory and present a generalized Cardy-Verlinde formula in this set-up

Chandra Reviews Black Hole Musical: Epic But Off-Key

Science.gov (United States)

2006-10-01

A gigantic sonic boom generated by a supermassive black hole has been found with NASA's Chandra X-ray Observatory, along with evidence for a cacophony of deep sound. This discovery was made by using data from the longest X-ray observation ever of M87, a nearby giant elliptical galaxy. M87 is centrally located in the Virgo cluster of galaxies and is known to harbor one of the Universe's most massive black holes. Scientists detected loops and rings in the hot, X-ray emitting gas that permeates the cluster and surrounds the galaxy. These loops provide evidence for periodic eruptions that occurred near the supermassive black hole, and that generate changes in pressure, or pressure waves, in the cluster gas that manifested themselves as sound. Chandra Low Energy X-ray Images of M87 Chandra Low Energy X-ray Images of M87 "We can tell that many deep and different sounds have been rumbling through this cluster for most of the lifetime of the Universe," said William Forman of the Harvard-Smithsonian Center for Astrophysics (CfA). The outbursts in M87, which happen every few million years, prevent the huge reservoir of gas in the cluster from cooling and forming many new stars. Without these outbursts and resultant heating, M87 would not be the elliptical galaxy it is today. "If this black hole wasn't making all of this noise, M87 could have been a completely different type of galaxy," said team member Paul Nulsen, also of the CfA, "possibly a huge spiral galaxy about 30 times brighter than the Milky Way." Chandra High Energy X-ray Image of M87 Chandra High Energy X-ray Image of M87 The outbursts result when material falls toward the black hole. While most of the matter is swallowed, some of it was violently ejected in jets. These jets are launched from regions close to the black hole (neither light nor sound can escape from the black hole itself) and push into the cluster's gas, generating cavities and sound which then propagate outwards. Chandra's M87 observations also

Black holes in binary stars

NARCIS (Netherlands)

Wijers, R.A.M.J.

1996-01-01

Introduction Distinguishing neutron stars and black holes Optical companions and dynamical masses X-ray signatures of the nature of a compact object Structure and evolution of black-hole binaries High-mass black-hole binaries Low-mass black-hole binaries Low-mass black holes Formation of black holes

Nonarteritic anterior ischemic optic neuropathy following pars plana vitrectomy for macular hole treatment: case report.

Science.gov (United States)

Cunha, Leonardo Provetti; Cunha, Luciana Virgínia Ferreira Costa; Costa, Carolina Ferreira; Monteiro, Mário Luiz Ribeiro

2016-01-01

Herein, we report a case of nonarteritic anterior ischemic optic neuropathy (NAION) following uneventful pars plana vitrectomy for macular hole treatment. A 56-year-old previously healthy woman presented with a full-thickness macular hole in right eye (OD) and small cup-to-disc ratios in both eyes. Five days after surgery, she noticed sudden painless loss of vision in OD and was found to have an afferent pupillary defect and intraocular pressure of 29 mmHg. Fundus examination showed right optic disc edema and the resolution of a macular hole with an inferior altitudinal visual field defect. Erythrocyte sedimentation rate, C-reactive protein levels, and general physical examination findings were normal. She was treated with hypotensive eyedrops and oral prednisone, resulting in mild visual improvement and a pale optic disc. A combination of face-down position and increased intraocular pressure due to a small optic disc cup were considered as potential mechanisms underlying NAION in the present case. Vitreoretinal surgeons should be aware of NAION as a potentially serious complication and be able to recognize associated risk factors and clinical findings.

The stable problem of the black-hole connected region in the Schwarzschild black hole

OpenAIRE

Tian, Guihua

2005-01-01

The stability of the Schwarzschild black hole is studied. Using the Painlev\\'{e} coordinate, our region can be defined as the black-hole-connected region(r>2m, see text) of the Schwarzschild black hole or the white-hole-connected region(r>2m, see text) of the Schwarzschild black hole. We study the stable problems of the black-hole-connected region. The conclusions are: (1) in the black-hole-connected region, the initially regular perturbation fields must have real frequency or complex frequen...

Rotating black holes at future colliders. III. Determination of black hole evolution

International Nuclear Information System (INIS)

Ida, Daisuke; Oda, Kin-ya; Park, Seong Chan

2006-01-01

TeV scale gravity scenario predicts that the black hole production dominates over all other interactions above the scale and that the Large Hadron Collider will be a black hole factory. Such higher-dimensional black holes mainly decay into the standard model fields via the Hawking radiation whose spectrum can be computed from the greybody factor. Here we complete the series of our work by showing the greybody factors and the resultant spectra for the brane-localized spinor and vector field emissions for arbitrary frequencies. Combining these results with the previous works, we determine the complete radiation spectra and the subsequent time evolution of the black hole. We find that, for a typical event, well more than half a black hole mass is emitted when the hole is still highly rotating, confirming our previous claim that it is important to take into account the angular momentum of black holes

Black holes. Chapter 6

International Nuclear Information System (INIS)

Penrose, R.

1980-01-01

Conditions for the formation of a black hole are considered, and the properties of black holes. The possibility of Cygnus X-1 as a black hole is discussed. Einstein's theory of general relativity in relation to the formation of black holes is discussed. (U.K.)

Pressure suppression apparatus of a nuclear power plant

International Nuclear Information System (INIS)

Mizumachi, W.; Funalashi, T.

1980-01-01

Pressure suppression apparatus for a nuclear reactor comprises a vessel surrounding a reactor pressure vessel and containing a water pool at the bottom of the vessel, and a steam exhaust pipe. The apparatus further comprises an exhaust chamber connected to the immersed portion of the exhaust pipe and provided with a number of discharge openings. (auth)

Statistical black-hole thermodynamics

International Nuclear Information System (INIS)

Bekenstein, J.D.

1975-01-01

Traditional methods from statistical thermodynamics, with appropriate modifications, are used to study several problems in black-hole thermodynamics. Jaynes's maximum-uncertainty method for computing probabilities is used to show that the earlier-formulated generalized second law is respected in statistically averaged form in the process of spontaneous radiation by a Kerr black hole discovered by Hawking, and also in the case of a Schwarzschild hole immersed in a bath of black-body radiation, however cold. The generalized second law is used to motivate a maximum-entropy principle for determining the equilibrium probability distribution for a system containing a black hole. As an application we derive the distribution for the radiation in equilibrium with a Kerr hole (it is found to agree with what would be expected from Hawking's results) and the form of the associated distribution among Kerr black-hole solution states of definite mass. The same results are shown to follow from a statistical interpretation of the concept of black-hole entropy as the natural logarithm of the number of possible interior configurations that are compatible with the given exterior black-hole state. We also formulate a Jaynes-type maximum-uncertainty principle for black holes, and apply it to obtain the probability distribution among Kerr solution states for an isolated radiating Kerr hole

Black hole hair removal

International Nuclear Information System (INIS)

Banerjee, Nabamita; Mandal, Ipsita; Sen, Ashoke

2009-01-01

Macroscopic entropy of an extremal black hole is expected to be determined completely by its near horizon geometry. Thus two black holes with identical near horizon geometries should have identical macroscopic entropy, and the expected equality between macroscopic and microscopic entropies will then imply that they have identical degeneracies of microstates. An apparent counterexample is provided by the 4D-5D lift relating BMPV black hole to a four dimensional black hole. The two black holes have identical near horizon geometries but different microscopic spectrum. We suggest that this discrepancy can be accounted for by black hole hair - degrees of freedom living outside the horizon and contributing to the degeneracies. We identify these degrees of freedom for both the four and the five dimensional black holes and show that after their contributions are removed from the microscopic degeneracies of the respective systems, the result for the four and five dimensional black holes match exactly.

Rita Bottoms: Polyartist Librarian

OpenAIRE

Bottoms, Rita; Reti, Irene; Regional History Project, UCSC Library

2005-01-01

Project Director Irene Reti conducted fourteen hours of interviews with Rita Bottoms, Head of Special Collections at the University Library, UC Santa Cruz, shortly before her retirement in March 2003. This oral history provides a vivid and intimate look at thirty-seven years behind the scenes in the library's Special Collections. For thirty-seven years Bottoms dedicated herself to collecting work by some of the most eminent writers and photographers of the twentieth century, includin...

Stability of black hole accretion disks

Directory of Open Access Journals (Sweden)

Czerny B.

2012-12-01

Full Text Available We discuss the issues of stability of accretion disks that may undergo the limit-cycle oscillations due to the two main types of thermal-viscous instabilities. These are induced either by the domination of radiation pressure in the innermost regions close to the central black hole, or by the partial ionization of hydrogen in the zone of appropriate temperatures. These physical processes may lead to the intermittent activity in AGN on timescales between hundreds and millions of years. We list a number of observational facts that support the idea of the cyclic activity in high accretion rate sources. We conclude however that the observed features of quasars may provide only indirect signatures of the underlying instabilities. Also, the support from the sources with stellar mass black holes, whose variability timescales are observationally feasible, is limited to a few cases of the microquasars. Therefore we consider a number of plausible mechanisms of stabilization of the limit cycle oscillations in high accretion rate accretion disks. The newly found is the stabilizing effect of the stochastic viscosity fluctuations.

Electron–hole two-stream instability in a quantum semiconductor plasma with exchange-correlation effects

International Nuclear Information System (INIS)

Zeba, I.; Yahia, M.E.; Shukla, P.K.; Moslem, W.M.

2012-01-01

The electron–hole two-stream instability in a quantum semiconductor plasma has been studied including electrons and holes quantum recoil effects, exchange-correlation potentials, and degenerate pressures of the plasma species. Typical values of GaAs and GaSb semiconductors are used to estimate the growth rate of the two-stream instability. The effects of electron– and hole–phonon collision, quantum recoil effects, the streaming velocities, and the corresponding threshold on the growth rate are investigated numerically. Considering the phonon susceptibility allows the acoustic mode to exist and the collisional instability arises in combination with drift of the holes. -- Highlights: ► Electron–hole two stream instability in quantum plasmas is presented. ► Typical values of GaAs and GaSb semiconductors are used to estimate the growth rate. ► The streaming velocities and the corresponding threshold on the growth rate are investigated numerically.

Shallow flows with bottom topography

NARCIS (Netherlands)

Heijst, van G.J.F.; Kamp, L.P.J.; Theunissen, R.; Rodi, W.; Uhlmann, M.

2012-01-01

This paper discusses laboratory experiments and numerical simulations of dipolar vortex flows in a shallow fluid layer with bottom topography. Two cases are considered: a step topography and a linearly sloping bottom. It is found that viscous effects – i.e., no-slip conditions at the non-horizontal

Factors affecting shut-in pressure rise: kicks in offshore HPHT wells

Energy Technology Data Exchange (ETDEWEB)

Schilhab, L C [Sedco Forex, (Country unknown/Code not available); Rezmer-Cooper, I M [Anadril, (Country unknown/Code not available)

1997-05-01

Deep water and HPHT operations are two areas where the use of sophisticated simulators can enable difficult processes and procedures to be broken down into individual identifiable contributions. In the paper we discuss some of the factors that are likely to affect shut-in pressure rise in offshore drilling operations, and how a simulator can be used to answer other, less obvious questions concerning deep water well control operations. We examine the effect of gas solubility by considering a gas-kick in a deep HPHT well drilled with oil-base mud. In this case, most of the influx will be dissolved in the mud, thus removing one of the processes for increasing the wellbore pressure. In terms of s safe state to disconnect from a well in rough weather, provided that the mud yield stress negates migration of the gas-cut mud, leaving the influx in solution at the bottom of the well should not lead to increasing wellbore pressures. Significant wellbore pressure effects may also occur after closing the blowout preventers (BOP`s) on a well without an influx (or with an influx in solution), and allowing the mud to heat up. We show that in typical HPHT geometries the pressure can rise by up to 8 bar/deg C. Similar magnitudes of pressure can also increase whilst circulating trapped gas out of a BOP at the end of a well control operation. We note that these effects may also be attenuated by fluid loss and wellbore compliance for wells with significant open hole sections. Indeed, gas trapped in the BOP should be safety removed by established well control procedures. However, preliminary studies with the simulator (and confirmed by field tests in the literature) have shown that an accidental release of a small amount of gas into a deep water riser may disperse, and not cause the riser to unload. (authors) 5 refs.

Thermodynamics of the Schwarzschild-AdS Black Hole with a Minimal Length

Directory of Open Access Journals (Sweden)

Yan-Gang Miao

2017-01-01

Full Text Available Using the mass-smeared scheme of black holes, we study the thermodynamics of black holes. Two interesting models are considered. One is the self-regular Schwarzschild-AdS black hole whose mass density is given by the analogue to probability densities of quantum hydrogen atoms. The other model is the same black hole but whose mass density is chosen to be a rational fractional function of radial coordinates. Both mass densities are in fact analytic expressions of the δ-function. We analyze the phase structures of the two models by investigating the heat capacity at constant pressure and the Gibbs free energy in an isothermal-isobaric ensemble. Both models fail to decay into the pure thermal radiation even with the positive Gibbs free energy due to the existence of a minimal length. Furthermore, we extend our analysis to a general mass-smeared form that is also associated with the δ-function and indicate the similar thermodynamic properties for various possible mass-smeared forms based on the δ-function.

NDE and fracture mechanics evaluation of bottom-head weld indications in a BWR reactor pressure vessel

Energy Technology Data Exchange (ETDEWEB)

Brickstad, B [Swedish Plant Inspectorate, Stockholm (Sweden)

1988-12-31

This document deals with the Non Destructive Examination (NDE) and the fracture mechanics evaluation of bottom head welds in a BWR. The NDE equipment is presented, together with the geometry of evaluated flaw regions. After the fracture mechanics evaluation, it appeared that the plant results fulfilled the usual conditions, and the plant was allowed to operate one more year. (TEC).

Ocean bottom pressure observations near the source of the 2011 Tohoku earthquake

Science.gov (United States)

Inazu, D.; Hino, R.; Suzuki, S.; Osada, Y.; Ohta, Y.; Iinuma, T.; Tsushima, H.; Ito, Y.; Kido, M.; Fujimoto, H.

2011-12-01

A Mw9.0 earthquake occurred off Miyagi, northeast Japan, on 11 March 2011 (hereafter mainshock). An earthquake of M7.3, considered to be the largest foreshock of the mainshock, occurred on 9 March 2011 near the mainshock hypocenter. A suite of seismic and geodetic variations related to these earthquakes was observed by autonomous, ocean bottom pressure (OBP) gauges at multiple sites (4 sites at present) near the sources within a distance of about 100 km. This paper presents the OBP records with a focus on the earthquakes. Thanks to correcting tides, instrumental drifts, and non-tidal oceanic variations, we can detect OBP signals of tsunamis and vertical seafloor deformation of the order of centimeters with timescales of less than months. In the following we review the detected signals and how to correct the OBP data. The coseismic seafloor displacement and the tsunami accompanied by the mainshock were of the order of meters and large enough to be distinctly identified (Ito et al., 2011, GRL). Co- and post-seismic seafloor displacement and tsunami accompanied by the foreshock were of the order of centimeters which is difficult to be identified from the raw OBP records. The first evident pulses of these tsunamis in the deep sea have durations (periods) of ~20 minutes and ~10 minutes, for the mainshock and the foreshock, respectively. Amounts of seafloor vertical displacement due to post-mainshock deformation reached a few tens of centimeters in two months. It is worth noting that elevation and depression of seafloor were detected at rates of a couple of centimeters in a day after the largest foreshock. The seafloor displacement of centimeters between the largest foreshock and the mainshock can be reasonably identified after correcting non-tidal oceanic variations. The oceanic variations are simulated by a barotropic ocean model driven by atmospheric disturbances (Inazu et al., 2011, Ann. Rep. Earth Simulator Center 2011). The model enables residual OBP time series of

Brane holes

International Nuclear Information System (INIS)

Frolov, Valeri P.; Mukohyama, Shinji

2011-01-01

The aim of this paper is to demonstrate that in models with large extra dimensions under special conditions one can extract information from the interior of 4D black holes. For this purpose we study an induced geometry on a test brane in the background of a higher-dimensional static black string or a black brane. We show that, at the intersection surface of the test brane and the bulk black string or brane, the induced metric has an event horizon, so that the test brane contains a black hole. We call it a brane hole. When the test brane moves with a constant velocity V with respect to the bulk black object, it also has a brane hole, but its gravitational radius r e is greater than the size of the bulk black string or brane r 0 by the factor (1-V 2 ) -1 . We show that bulk ''photon'' emitted in the region between r 0 and r e can meet the test brane again at a point outside r e . From the point of view of observers on the test brane, the events of emission and capture of the bulk photon are connected by a spacelike curve in the induced geometry. This shows an example in which extra dimensions can be used to extract information from the interior of a lower-dimensional black object. Instead of the bulk black string or brane, one can also consider a bulk geometry without a horizon. We show that nevertheless the induced geometry on the moving test brane can include a brane hole. In such a case the extra dimensions can be used to extract information from the complete region of the brane-hole interior. We discuss thermodynamic properties of brane holes and interesting questions which arise when such an extra-dimensional channel for the information mining exists.

Research on Hydrodynamic Interference Suppression of Bottom-Mounted Monitoring Platform with Fairing Structure

Science.gov (United States)

Wang, Zhen; Zheng, Yi; Mao, Yu-feng; Wang, Ya-zhou; Yu, Yan-ting; Liu, Hong-ning

2018-03-01

In the disturbance of unsteady flow field under the sea, the monitoring accuracy and precision of the bottom-mounted acoustic monitoring platform will decrease. In order to reduce the hydrodynamic interference, the platform wrapped with fairing structure and separated from the retrieval unit is described. The suppression effect evaluation based on the correlation theory of sound pressure and particle velocity for spherical wave in infinite homogeneous medium is proposed and the difference value between them is used to evaluate the hydrodynamic restraining performance of the bottom-mounted platform under far field condition. Through the sea test, it is indicated that the platform with sparse layers fairing structure (there are two layers for the fairing, in which the inside layer is 6-layers sparse metal net, and the outside layer is 1-layer polyester cloth, and then it takes sparse layers for short) has no attenuation in the sound pressure response to the sound source signal, but obvious suppression in the velocity response to the hydrodynamic noise. The effective frequency of the fairing structure is decreased below 10 Hz, and the noise magnitude is reduced by 10 dB. With the comparison of different fairing structures, it is concluded that the tighter fairing structure can enhance the performance of sound transmission and flow restraining.

Static black hole and vacuum energy: thin shell and incompressible fluid

Science.gov (United States)

Ho, Pei-Ming; Matsuo, Yoshinori

2018-03-01

With the back reaction of the vacuum energy-momentum tensor consistently taken into account, we study static spherically symmetric black-hole-like solutions to the semi-classical Einstein equation. The vacuum energy is assumed to be given by that of 2-dimensional massless scalar fields, as a widely used model in the literature for black holes. The solutions have no horizon. Instead, there is a local minimum in the radius. We consider thin shells as well as incompressible fluid as the matter content of the black-hole-like geometry. The geometry has several interesting features due to the back reaction of vacuum energy. In particular, Buchdahl's inequality can be violated without divergence in pressure, even if the surface is below the Schwarzschild radius. At the same time, the surface of the star can not be far below the Schwarzschild radius for a density not much higher than the Planck scale, and the proper distance from its surface to the origin can be very short even for very large Schwarzschild radius. The results also imply that, contrary to the folklore, in principle the Boulware vacuum can be physical for black holes.

Peach Bottom Turbine Trip Simulations with RETRAN Using INER/TPC BWR Transient Analysis Method

International Nuclear Information System (INIS)

Kao Lainsu; Chiang, Show-Chyuan

2005-01-01

The work described in this paper is benchmark calculations of pressurization transient turbine trip tests performed at the Peach Bottom boiling water reactor (BWR). It is part of an overall effort in providing qualification basis for the INER/TPC BWR transient analysis method developed for the Kuosheng and Chinshan plants. The method primarily utilizes an advanced system thermal hydraulics code, RETRAN02/MOD5, for transient safety analyses. Since pressurization transients would result in a strong coupling effect between core neutronic and system thermal hydraulics responses, the INER/TPC method employs the one-dimensional kinetic model in RETRAN with a cross-section data library generated by the Studsvik-CMS code package for the transient calculations. The Peach Bottom Turbine Trip (PBTT) tests, including TT1, TT2, and TT3, have been successfully performed in the plant and assigned as standards commonly for licensing method qualifications for years. It is an essential requirement for licensing purposes to verify integral capabilities and accuracies of the codes and models of the INER/TPC method in simulating such pressurization transients. Specific Peach Bottom plant models, including both neutronics and thermal hydraulics, are developed using modeling approaches and experiences generally adopted in the INER/TPC method. Important model assumptions in RETRAN for the PBTT test simulations are described in this paper. Simulation calculations are performed with best-estimated initial and boundary conditions obtained from plant test measurements. The calculation results presented in this paper demonstrate that the INER/TPC method is capable of calculating accurately the core and system transient behaviors of the tests. Excellent agreement, both in trends and magnitudes between the RETRAN calculation results and the PBTT measurements, shows reliable qualifications of the codes/users/models involved in the method. The RETRAN calculated peak neutron fluxes of the PBTT

Black holes are warm

International Nuclear Information System (INIS)

Ravndal, F.

1978-01-01

Applying Einstein's theory of gravitation to black holes and their interactions with their surroundings leads to the conclusion that the sum of the surface areas of several black holes can never become less. This is shown to be analogous to entropy in thermodynamics, and the term entropy is also thus applied to black holes. Continuing, expressions are found for the temperature of a black hole and its luminosity. Thermal radiation is shown to lead to explosion of the black hole. Numerical examples are discussed involving the temperature, the mass, the luminosity and the lifetime of black mini-holes. It is pointed out that no explosions corresponding to the prediction have been observed. It is also shown that the principle of conservation of leptons and baryons is broken by hot black holes, but that this need not be a problem. The related concept of instantons is cited. It is thought that understanding of thermal radiation from black holes may be important for the development of a quantified gravitation theory. (JIW)

Exploring nuclear magnetic resonance at the highest pressure. Closing the pseudogap under pressure in a high temperature superconductor

Energy Technology Data Exchange (ETDEWEB)

Meissner, Thomas

2013-05-13

that a two component spin susceptibility in the copper-oxide plane is a common feature of cuprates. Finally, an almost linear increase of the {sup 63}Cu quadrupole frequency of planar copper in YBa{sub 2}Cu{sub 4}O{sub 8} up to 42 kbar is observed. It is attributable either to a pressure induced hole transfer from the planar oxygen 2p orbitals to the planar copper 3d{sub x{sup 2}-y{sup 2}} orbitals or to a pressure induced hole transfer into the copper-oxide plane. The latter may be more likely since earlier transport measurements up to 16 kbar identified a pressure induced hole transfer from the copper-oxide chains to the copper-oxide plane in this material [137, 138]. However, such a hole transfer into the copper-oxide plane is found to be insufficient to explain the rapid increase of T{sub c} in YBa{sub 2}Cu{sub 4}O{sub 8} under pressure as was suggested earlier [134]. Further experiments are required to determine the hole distribution in the copper-oxide plane and to clarify the role of the hole transfer in the closing of the pseudogap in YBa{sub 2}Cu{sub 4}O{sub 8} at high pressure. In conclusion it can be said that research at very high pressure gives a unique insight into the physics of materials that is also pivotal for their understanding at ambient pressure. However, up until now many physical properties were inaccessible under such extreme conditions due to a lack of suitable experimental probes. In this regard, NMR at very high pressure offers new information and will therefore prove to be an important tool in the future.

Exploring nuclear magnetic resonance at the highest pressure. Closing the pseudogap under pressure in a high temperature superconductor

International Nuclear Information System (INIS)

Meissner, Thomas

2013-01-01

, an almost linear increase of the 63 Cu quadrupole frequency of planar copper in YBa 2 Cu 4 O 8 up to 42 kbar is observed. It is attributable either to a pressure induced hole transfer from the planar oxygen 2p orbitals to the planar copper 3d x 2 -y 2 orbitals or to a pressure induced hole transfer into the copper-oxide plane. The latter may be more likely since earlier transport measurements up to 16 kbar identified a pressure induced hole transfer from the copper-oxide chains to the copper-oxide plane in this material [137, 138]. However, such a hole transfer into the copper-oxide plane is found to be insufficient to explain the rapid increase of T c in YBa 2 Cu 4 O 8 under pressure as was suggested earlier [134]. Further experiments are required to determine the hole distribution in the copper-oxide plane and to clarify the role of the hole transfer in the closing of the pseudogap in YBa 2 Cu 4 O 8 at high pressure. In conclusion it can be said that research at very high pressure gives a unique insight into the physics of materials that is also pivotal for their understanding at ambient pressure. However, up until now many physical properties were inaccessible under such extreme conditions due to a lack of suitable experimental probes. In this regard, NMR at very high pressure offers new information and will therefore prove to be an important tool in the future.

Apparatus for sealing access holes to cavities within the earth with rock glass

International Nuclear Information System (INIS)

Holman, R.R.

1979-01-01

Apparatus is disclosed for establishing a solid, very low permeable rock glass plug to seal access holes through rock to underground storage vaults. The apparatus is designed to supply a filler material having a constituency substantially matching that of the rock formation surrounding the access port to the vault, through a central feeder tube under pressure to the vault. Means are provided for heating the filler material and surrounding rock formation at the point where the filler material exits the feeder tube, to a temperature sufficient to melt both the rock formation and the filler material. The remaining portion of the feeder tube is cooled to preserve the surrounding rock formaion spaced from the feeder orifice. The melt at the extremity of the feeder tube is forced through the orifice to a region below the tool by the force of the pressure feed. As the melt is forced below the tool, the tool is retracted until the access hole is completely sealed. A second embodiment is provided to seal enlarged openings which further includes a cooled core follower that enables the deposit to be fused in layers closing in the circumference of the hole until a final pass fuses the central core

Cracking and Failure in Rock Specimen Containing Combined Flaw and Hole under Uniaxial Compression

Directory of Open Access Journals (Sweden)

Xiang Fan

2018-01-01

Full Text Available Flaw is a key factor influencing failure behavior of a fractured specimen. In the present study, rectangular-flawed specimens were prepared using sandstone to investigate the effect of flaw on failure behavior of rock. Open flaw and cylindrical hole were simultaneously precut within rock specimens using high-pressure water jet cutting technology. Five series of specimens including intact, single-hole-alone, two-hole-alone, single-hole and two-flaw, and two-hole and single-flaw blocks were prepared. Uniaxial compressive tests using a rigid servo control instrument were carried out to investigate the fracture processes of these flawed specimens. It is observed that during loading, internal stress always intensively distributed at both sidewalls of open hole, especially at midpoint of sidewalls, so rock crumb flaking was firstly observed among all sandstone specimens containing single hole or two holes. Cracking around open hole is associated with the flaw inclination angle which was observed in Series III and V. Crack easily initiated at the tips of flaw with inclination angles of 0°, 30°, and 60° but hard for 90° in Series III and V. Rock burst was the major failure mode among most tested specimens, which generally induced new cracks and finally created crater shape. Additionally, due to extrusion between blocks, new shear or tensile cracks were generated and the rock specimen surface spalled. Eventually, four typical failure processes including rock crumb flaking, crack initiation and propagation, rock burst, and second rupture, were summarized.

Quantum aspects of black holes

CERN Document Server

2015-01-01

Beginning with an overview of the theory of black holes by the editor, this book presents a collection of ten chapters by leading physicists dealing with the variety of quantum mechanical and quantum gravitational effects pertinent to black holes. The contributions address topics such as Hawking radiation, the thermodynamics of black holes, the information paradox and firewalls, Monsters, primordial black holes, self-gravitating Bose-Einstein condensates, the formation of small black holes in high energetic collisions of particles, minimal length effects in black holes and small black holes at the Large Hadron Collider. Viewed as a whole the collection provides stimulating reading for researchers and graduate students seeking a summary of the quantum features of black holes.

Spatiotemporal distribution of interplate slip following the 2003 Tokachi-oki earthquake deduced from ocean bottom pressure gauges and onland GNSS data

Science.gov (United States)

Itoh, Y.; Nishimura, T.; Ariyoshi, K.; Matsumoto, H.

2017-12-01

The 2003 Tokachi-oki earthquake (Mw 8.0) is an interplate earthquake along the Kurile trench. Its co- and post-seismic deformation has been observed by onland GNSS [e.g., Miyazaki et al. 2004] and modeled with afterslip and/or viscoelastic relaxation [e.g., Itoh and Nishimura 2016]. In the offshore region, two ocean bottom pressure gauges (OBPs) are operated by JAMSTEC since July 1999 [Hirata et al. 2002] and they have continuously observed the pre-, co- and post-seismic pressure change of the 2003 event [Baba et al. 2006]. The observed pressure change can be interpreted as vertical displacement, and the resolution of slip beneath the seafloor far from the land was improved by incorporating these pressure data into onland GNSS data [Baba et al. 2006]. However, no previous studies used postseismic pressure data for several years to estimate an interplate slip. Because, in this region, an M8 class event similar to the 2003 event has occurred in 1952, it is important to clarify a healing process of an interplate coupling which may lead to a next M8 class event in terms of the earthquake cycle. Itoh and Nishimura [2017, JpGU-AGU Joint Meeting] estimated it but used only onland GNSS data. In this study, we use both onland GNSS and OBP data. For OBP data analysis, we first removed the tidal component using BAYTAP08 [Tamura et al. 1991; Tamura and Agnew 2008]. Next, we corrected the temporal fluctuation of data correlating with temperature [Baba et al. 2006]. We estimated the linear trend before the 2003 event using the corrected time series from 2002 Jan. 1 to 2003 Sep. 1 and remove the estimated trend from the data after the 2003 event. Here, we assumed a non-linear drift could be ignored. Finally, we down-sampled the remained time series with an interval of 1 month. For the onland GNSS data, we used the same data set of Itoh and Nishimura [2017, JpGU-AGU Joint Meeting]. We constructed the model consisting of coseismic slip of the 2003 and M6-7 events in the postseismic

Dependence of steam generator vibrations on feedwater pressure

International Nuclear Information System (INIS)

Sadilek, J.

1989-01-01

Vibration sensors are attached to the bottom of the steam generator jacket between the input and output primary circuit collectors. The effective vibration value is recorded daily. Several times higher vibrations were observed at irregular intervals; their causes were sought, and the relation between the steam generator vibrations measured at the bottom of its vessel and the feedwater pressure was established. The source of the vibrations was found to be in the feedwater tract of the steam generator. The feedwater tract is described and its hydraulic characteristics are given. Vibrations were measured on the S02 valve. It is concluded that vibrations can be eliminated by reducing the water pressure before the control valves and by replacing the control valves with ones with more suitable control characteristics. (E.J.). 3 figs., 1 tab., 3 refs

Black holes and beyond

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

Belief in the existence of black holes is the ultimate act of faith for a physicist. First suggested by the English clergyman John Michell in the year 1784, the gravitational pull of a black hole is so strong that nothing - not even light - can escape. Gravity might be the weakest of the fundamental forces but black-hole physics is not for the faint-hearted. Black holes present obvious problems for would-be observers because they cannot, by definition, be seen with conventional telescopes - although before the end of the decade gravitational-wave detectors should be able to study collisions between black holes. Until then astronomers can only infer the existence of a black hole from its gravitational influence on other matter, or from the X-rays emitted by gas and dust as they are dragged into the black hole. However, once this material passes through the 'event horizon' that surrounds the black hole, we will never see it again - not even with X-ray specs. Despite these observational problems, most physicists and astronomers believe that black holes do exist. Small black holes a few kilometres across are thought to form when stars weighing more than about two solar masses collapse under the weight of their own gravity, while supermassive black holes weighing millions of solar masses appear to be present at the centre of most galaxies. Moreover, some brave physicists have proposed ways to make black holes - or at least event horizons - in the laboratory. The basic idea behind these 'artificial black holes' is not to compress a large amount of mass into a small volume, but to reduce the speed of light in a moving medium to less than the speed of the medium and so create an event horizon. The parallels with real black holes are not exact but the experiments could shed new light on a variety of phenomena. The first challenge, however, is to get money for the research. One year on from a high-profile meeting on artificial black holes in London, for

Numerical Simulation of the Depressurization Process of a Natural Gas Hydrate Reservoir: An Attempt at Optimization of Field Operational Factors with Multiple Wells in a Real 3D Geological Model

Directory of Open Access Journals (Sweden)

Zhixue Sun

2016-09-01

Full Text Available Natural gas hydrates, crystalline solids whose gas molecules are so compressed that they are denser than a typical fluid hydrocarbon, have extensive applications in the areas of climate change and the energy crisis. The hydrate deposit located in the Shenhu Area on the continental slope of the South China Sea is regarded as the most promising target for gas hydrate exploration in China. Samples taken at drilling site SH2 have indicated a high abundance of methane hydrate reserves in clay sediments. In the last few decades, with its relatively low energy cost, the depressurization gas recovery method has been generally regarded as technically feasible and the most promising one. For the purpose of a better acquaintance with the feasible field operational factors and processes which control the production behavior of a real 3D geological CH4-hydrate deposit, it is urgent to figure out the effects of the parameters such as well type, well spacing, bottom hole pressure, and perforation intervals on methane recovery. One years’ numerical simulation results show that under the condition of 3000 kPa constant bottom hole pressure, 1000 m well spacing, perforation in higher intervals and with one horizontal well, the daily peak gas rate can reach 4325.02 m3 and the cumulative gas volume is 1.291 × 106 m3. What’s more, some new knowledge and its explanation of the curve tendency and evolution for the production process are provided. Technically, one factor at a time design (OFAT and an orthogonal design were used in the simulation to investigate which factors dominate the productivity ability and which is the most sensitive one. The results indicated that the order of effects of the factors on gas yield was perforation interval > bottom hole pressure > well spacing.

The cost of pressure ulcers in the UK.

Science.gov (United States)

Bennett, Gerry; Dealey, Carol; Posnett, John

2004-05-01

To estimate the annual cost of treating pressure ulcers in the UK. Costs were derived from a bottom-up methodology, based on the daily resources required to deliver protocols of care reflecting good clinical practice. Health and social care system in the UK. Patients developing a pressure ulcer. A bottom-up costing approach is used to estimate treatment cost per episode of care and per patient for ulcers of different grades and level of complications. Also, total treatment cost to the health and social care system in the UK. The cost of treating a pressure ulcer varies from pound 1,064 (Grade 1) to pound 10,551 (Grade 4). Costs increase with ulcer grade because the time to heal is longer and because the incidence of complications is higher in more severe cases. The total cost in the UK is pound 1.4- pound 2.1 billion annually (4% of total NHS expenditure). Most of this cost is nurse time. Pressure ulcers represent a very significant cost burden in the UK. Without concerted effort this cost is likely to increase in the future as the population ages. To the extent that pressure ulcers are avoidable, pressure damage may be indicative of clinical negligence and there is evidence that litigation could soon become a significant threat to healthcare providers in the UK, as it is in the USA.

Electronic States in Thorium under Pressure

DEFF Research Database (Denmark)

Skriver, Hans Lomholt; Jan, J. P.

1980-01-01

We have used the local-density formalism and the atomic-sphere approximation to calculate self-consistently the electronic properties of thorium at pressures up to 400 kbar. The derived equation of state agrees very well with static pressure experiments and shock data. Below the Fermi level (EF......) the electronic band structure is formed by 7s and 6d states while the bottom of a relatively broad 5f band is positioned 0.07 Ry above EF. The calculated extremal areas of the Fermi surface and their calculated pressure dependence agree with earlier calculations and with de Haas-van Alphen measurements...

Exploration of the West Florida Shelf Blue Holes Investigation of Physical and Biological Characteristics and Archaeological Implications of Unique Karst Features

Science.gov (United States)

Culter, J. K.

2006-12-01

of the documentation of the features included; vertical video transects, still photography, collections of biota, placement of recording thermographs and conductivity meters, collection of bottom sediment and rocks. During the course of the investigation a previously unknown cave feature over 45 meters in height and 76 meters in bottom diameter was discovered and dubbed Megadome. The cave is connected to the Gulf by a circular shaft approximately 0.75 meters in diameter and 11 meters in length. Instrumentation placed at Megadome revealed lunar tidal period water exchange, possible freshwater outflow and water movement in response to hurricanes. The upper portion of the cave contains a fouling community of sponges worms, tunicates and other organisms. A sink hole off the mouth of Tampa Bay was shown to contain a saltwater spring, venting at 72 m (235 fsw). Research is continuing. This research has been supported by a grant from NOAA, Ocean Exploration Program and Mote Marine Laboratory.

Investigation of Spiral and Sweeping Holes

Science.gov (United States)

Thurman, Douglas; Poinsatte, Philip; Ameri, Ali; Culley, Dennis; Raghu, Surya; Shyam, Vikram

2015-01-01

Surface infrared thermography, hotwire anemometry, and thermocouple surveys were performed on two new film cooling hole geometries: spiral/rifled holes and fluidic sweeping holes. The spiral holes attempt to induce large-scale vorticity to the film cooling jet as it exits the hole to prevent the formation of the kidney shaped vortices commonly associated with film cooling jets. The fluidic sweeping hole uses a passive in-hole geometry to induce jet sweeping at frequencies that scale with blowing ratios. The spiral hole performance is compared to that of round holes with and without compound angles. The fluidic hole is of the diffusion class of holes and is therefore compared to a 777 hole and Square holes. A patent-pending spiral hole design showed the highest potential of the non-diffusion type hole configurations. Velocity contours and flow temperature were acquired at discreet cross-sections of the downstream flow field. The passive fluidic sweeping hole shows the most uniform cooling distribution but suffers from low span-averaged effectiveness levels due to enhanced mixing. The data was taken at a Reynolds number of 11,000 based on hole diameter and freestream velocity. Infrared thermography was taken for blowing rations of 1.0, 1.5, 2.0, and 2.5 at a density ration of 1.05. The flow inside the fluidic sweeping hole was studied using 3D unsteady RANS.

Deep-Sea Mega-Epibenthic Assemblages from the SW Portuguese Margin (NE Atlantic Subjected to Bottom-Trawling Fisheries

Directory of Open Access Journals (Sweden)

Sofia P. Ramalho

2017-11-01

Full Text Available Bottom-trawling fisheries are a common threat to the health of continental margins worldwide. Together with numerous environmental and biological processes, physical disturbance induced by trawlers can largely shape the benthic habitats and their associated assemblages. At the SW Portuguese Margin, crustacean bottom trawlers have exploited deep-sea habitats for a few decades, but its effects on the benthic biodiversity are practically unknown. During the spring-summer of 2013 and 2014, several Remotely Operated Vehicle (ROV video transects were used to investigate mega-epibenthic abundance, composition, and diversity in soft-sediment areas subjected to varying trawling pressures off Sines and Setúbal (200–800 m. Differences in mega-epibenthic assemblages were linked with environmental changes (depth, grain size, primary productivity and trawling disturbance. The effect of trawling was assessed between segments with similar habitat characteristics, i.e., muddy-sand bottoms between 300 and 500 m. Areas subjected to intensive trawling pressure showed a generally flattened seabed, with abundant recent trawl marks (up to 3 scars.100 m−1, indicating that the seabed physical integrity was compromised. Significant negative correlations were detected between various mega-epibenthic diversity indices [S, H′, and ET(20] and trawling pressure (h.cell−1.y−1. Furthermore, the distinct mega-epibenthic assemblages and absence of several sessile erect morphospecies at both low and highly disturbed locations by trawling off Sines, namely all seapen morphospecies found in non-trawled areas, demonstrates the negative influence of trawling fisheries on the benthic component of the study area. Also, low dissimilarity between assemblages from the main fishing grounds and the adjacent low-disturbance locations, suggests that the potentially negative influence of trawling can extend beyond the targeted areas (e.g., by the plumes of re-suspended sediments. The

Black Hole Area Quantization rule from Black Hole Mass Fluctuations

OpenAIRE

Schiffer, Marcelo

2016-01-01

We calculate the black hole mass distribution function that follows from the random emission of quanta by Hawking radiation and with this function we calculate the black hole mass fluctuation. From a complete different perspective we regard the black hole as quantum mechanical system with a quantized event horizon area and transition probabilities among the various energy levels and then calculate the mass dispersion. It turns out that there is a perfect agreement between the statistical and ...

Effect of fluid penetration on tensile failure during fracturing of an open-hole wellbore

Science.gov (United States)

Zeng, Fanhui; Cheng, Xiaozhao; Guo, Jianchun; Chen, Zhangxin; Tao, Liang; Liu, Xiaohua; Jiang, Qifeng; Xiang, Jianhua

2018-06-01

It is widely accepted that a fracture can be induced at a wellbore surface when the fluid pressure overcomes the rock tensile strength. However, few models of this phenomenon account for the fluid penetration effect. A rock is a typical permeable, porous medium, and the transmission of pressure from a wellbore to the surrounding rock temporally and spatially perturbs the effective stresses. In addition, these induced stresses influence the fracture initiation pressure. To gain a better understanding of the penetration effect on the initiation pressure of a permeable formation, a comprehensive formula is presented to study the effects of the in situ stresses, rock mechanical properties, injection rate, rock permeability, fluid viscosity, fluid compressibility and wellbore size on the magnitude of the initiation pressure during fracturing of an open-hole wellbore. In this context, the penetration effect is treated as a consequence of the interaction among these parameters by using Darcy’s law of radial flow. A fully coupled analytical procedure is developed to show how the fracturing fluid infiltrates the rock around the wellbore and considerably reduces the magnitude of the initiation pressure. Moreover, the calculation results are validated by hydraulic fracturing experiments in hydrostone. An exhaustive sensitivity study is performed, indicating that the local fluid pressure induced from a seepage effect strongly influences the fracture evolution. For permeable reservoirs, a low injection rate and a low viscosity of the injected fluid have a significant impact on the fracture initiation pressure. In this case, the Hubbert and Haimson equations to predict the fracture initiation pressure are not valid. The open-hole fracture initiation pressure increases with the fracturing fluid viscosity and fluid compressibility, while it decreases as the rock permeability, injection rate and wellbore size increase.

Standard practice for examination of liquid-Filled atmospheric and Low-pressure metal storage tanks using acoustic emission

CERN Document Server

American Society for Testing and Materials. Philadelphia

2007-01-01

1.1 This practice covers guidelines for acoustic emission (AE) examinations of new and in-service aboveground storage tanks of the type used for storage of liquids. 1.2 This practice will detect acoustic emission in areas of sensor coverage that are stressed during the course of the examination. For flat-bottom tanks these areas will generally include the sidewalls (and roof if pressure is applied above the liquid level). The examination may not detect flaws on the bottom of flat-bottom tanks unless sensors are located on the bottom. 1.3 This practice may require that the tank experience a load that is greater than that encountered in normal use. The normal contents of the tank can usually be used for applying this load. 1.4 This practice is not valid for tanks that will be operated at a pressure greater than the examination pressure. 1.5 It is not necessary to drain or clean the tank before performing this examination. 1.6 This practice applies to tanks made of carbon steel, stainless steel, aluminum and oth...

Tribology aspects of a pressure vessel closure subjected to pressure cycling

International Nuclear Information System (INIS)

George, A.F.; Williams, M.E.

1988-04-01

A repair method being considered for a steel pressure vessel is to cut away the faulty part leaving an unreinforced circular hole in the curved wall and cover it with a sealed plate placed inside. In order to investigate the structural properties of such a repair a large model vessel (6m by 2m) was tested under pressure (about 2.5 MPa) and pressure cycling. This cycling caused relative movements at the loaded interface between the lid and the vessel. A tribological examination of the rubbing surfaces was carried out. The tribological examination is described and a small supporting programme of laboratory scaling tests. It gives the results and attempts to interpret them with particular attention given to wear, fretting fatigue and scaling to plant conditions. (author)

A CMOS pressure sensor with integrated interface for passive RFID applications

International Nuclear Information System (INIS)

Deng, Fangming; He, Yigang; Wu, Xiang; Fu, Zhihui

2014-01-01

This paper presents a CMOS pressure sensor with integrated interface for passive RFID sensing applications. The pressure sensor consists of three parts: top electrode, dielectric layer and bottom electrode. The dielectric layer consists of silicon oxide and an air gap. The bottom electrode is made of polysilicon. The gap is formed by sacrificial layer release and the Al vapor process is used to seal the gap and form the top electrode. The sensor interface is based on phase-locked architecture, which allows the use of fully digital blocks. The proposed pressure sensor and interface is fabricated in a 0.18 μm CMOS process. The measurement results show the pressure sensor achieves excellent linearity with a sensitivity of 1.2 fF kPa −1 . The sensor interface consumes only 1.1 µW of power at 0.5 V voltage supply, which is at least an order of magnitude better than state-of-the-art designs. (paper)

Monopole Black Hole Skyrmions

OpenAIRE

Moss, Ian G; Shiiki, N; Winstanley, E

2000-01-01

Charged black hole solutions with pion hair are discussed. These can be\\ud used to study monopole black hole catalysis of proton decay.\\ud There also exist\\ud multi-black hole skyrmion solutions with BPS monopole behaviour.

Can a primordial black hole or wormhole grow as fast as the universe?

International Nuclear Information System (INIS)

Carr, B J; Harada, Tomohiro; Maeda, Hideki

2010-01-01

This review addresses the issue of whether there are physically realistic self-similar solutions in which a primordial black hole is attached to an exact or asymptotically Friedmann model for an equation of state of the form p = (γ - 1)ρc 2 . In the positive-pressure case (1 < γ < 2), there is no solution in which the black hole is attached to an exact Friedmann background via a sonic point. However, there is a one-parameter family of black hole solutions which are everywhere supersonic and asymptotically quasi-Friedmann, in the sense that they contain a solid angle deficit at large distances. Such solutions exist providing the ratio of the black hole size to the cosmological horizon size is above some critical value and they include 'universal' black holes with an apparent horizon but no event horizon. In the stiff case (γ = 2), there is no self-similar solution in an exact background unless the matter turns into null dust before entering the event horizon; otherwise the only black hole solutions are probably asymptotically quasi-Friedmann universal ones. For a dark-energy-dominated universe (0 < γ < 2/3), there is a one-parameter family of black hole solutions which are properly asymptotically Friedmann (i.e. with no angle deficit) and the ratio of the black hole size to the cosmological horizon size is below some critical value. Above this value, one finds a self-similar cosmological wormhole solution which connects two asymptotic regions: one exactly Friedmann and the other asymptotically quasi-Friedmann. We also consider the possibility of self-similar black hole solutions in a universe dominated by a scalar field. This is like the stiff fluid case if the field is massless, but the situation is less clear if the scalar field is rolling down a potential and therefore massive, as in the quintessence scenario. Although no explicit asymptotically Friedmann black hole solutions of this kind are known, they may exist if the black hole is not too large. (brief

Can a primordial black hole or wormhole grow as fast as the universe?

Energy Technology Data Exchange (ETDEWEB)

Carr, B J [Astronomy Unit, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); Harada, Tomohiro [Department of Physics, Rikkyo University, Tokyo 171-8501 (Japan); Maeda, Hideki, E-mail: B.J.Carr@qmul.ac.u, E-mail: harada@rikkyo.ac.j, E-mail: hideki@cecs.c [Centro de Estudios Cientificos (CECS), Casilla 1469, Valdivia (Chile)

2010-09-21

This review addresses the issue of whether there are physically realistic self-similar solutions in which a primordial black hole is attached to an exact or asymptotically Friedmann model for an equation of state of the form p = ({gamma} - 1){rho}c{sup 2}. In the positive-pressure case (1 < {gamma} < 2), there is no solution in which the black hole is attached to an exact Friedmann background via a sonic point. However, there is a one-parameter family of black hole solutions which are everywhere supersonic and asymptotically quasi-Friedmann, in the sense that they contain a solid angle deficit at large distances. Such solutions exist providing the ratio of the black hole size to the cosmological horizon size is above some critical value and they include 'universal' black holes with an apparent horizon but no event horizon. In the stiff case ({gamma} = 2), there is no self-similar solution in an exact background unless the matter turns into null dust before entering the event horizon; otherwise the only black hole solutions are probably asymptotically quasi-Friedmann universal ones. For a dark-energy-dominated universe (0 < {gamma} < 2/3), there is a one-parameter family of black hole solutions which are properly asymptotically Friedmann (i.e. with no angle deficit) and the ratio of the black hole size to the cosmological horizon size is below some critical value. Above this value, one finds a self-similar cosmological wormhole solution which connects two asymptotic regions: one exactly Friedmann and the other asymptotically quasi-Friedmann. We also consider the possibility of self-similar black hole solutions in a universe dominated by a scalar field. This is like the stiff fluid case if the field is massless, but the situation is less clear if the scalar field is rolling down a potential and therefore massive, as in the quintessence scenario. Although no explicit asymptotically Friedmann black hole solutions of this kind are known, they may exist if the

Skyrmion black hole hair: Conservation of baryon number by black holes and observable manifestations

Energy Technology Data Exchange (ETDEWEB)

Dvali, Gia [Arnold Sommerfeld Center, Ludwig-Maximilians-Universität, 80333 München (Germany); Max-Planck-Institut für Physik, Werner-Heisenberg-Institut, 80805 München (Germany); Center for Cosmology and Particle Physics, Department of Physics, New York University, 4 Washington Place, New York, NY 10003 (United States); Gußmann, Alexander, E-mail: alexander.gussmann@physik.uni-muenchen.de [Arnold Sommerfeld Center, Ludwig-Maximilians-Universität, 80333 München (Germany)

2016-12-15

We show that the existence of black holes with classical skyrmion hair invalidates standard proofs that global charges, such as the baryon number, cannot be conserved by a black hole. By carefully analyzing the standard arguments based on a Gedankenexperiment in which a black hole is seemingly-unable to return the baryon number that it swallowed, we identify inconsistencies in this reasoning, which does not take into the account neither the existence of skyrmion black holes nor the baryon/skyrmion correspondence. We then perform a refined Gedankenexperiment by incorporating the new knowledge and show that no contradiction with conservation of baryon number takes place at any stage of black hole evolution. Our analysis also indicates no conflict between semi-classical black holes and the existence of baryonic gauge interaction arbitrarily-weaker than gravity. Next, we study classical cross sections of a minimally-coupled massless probe scalar field scattered by a skyrmion black hole. We investigate how the skyrmion hair manifests itself by comparing this cross section with the analogous cross section caused by a Schwarzschild black hole which has the same ADM mass as the skyrmion black hole. Here we find an order-one difference in the positions of the characteristic peaks in the cross sections. The peaks are shifted to smaller scattering angles when the skyrmion hair is present. This comes from the fact that the skyrmion hair changes the near horizon geometry of the black hole when compared to a Schwarzschild black hole with same ADM mass. We keep the study of this second aspect general so that the qualitative results which we obtain can also be applied to black holes with classical hair of different kind.

Growth optimization and characterization of GaN epilayers on multifaceted (111) surfaces etched on Si(100) substrates

Energy Technology Data Exchange (ETDEWEB)

Ansah-Antwi, KwaDwo Konadu, E-mail: kakadee@gmail.com; Chua, Soo Jin [Institute of Materials Research and Engineering (IMRE), A*STAR (Agency for Science, Technology and Research), 2 Fusionopolis Way, Innovis # 08-03, Singapore 138634 (Singapore); Department of Electrical and Computer Engineering, National University of Singapore, E4-5-45, 4 Engineering Drive 3, Singapore 117576 (Singapore); Soh, Chew Beng [Singapore Institute of Technology, 10 Dover Drive, Singapore 138683 (Singapore); Liu, Hongfei [Institute of Materials Research and Engineering (IMRE), A*STAR (Agency for Science, Technology and Research), 2 Fusionopolis Way, Innovis # 08-03, Singapore 138634 (Singapore)

2015-11-15

The four nearest Si(111) multifaceted sidewalls were exposed inside an array of 3 μm-wide square holes patterned on an Si(100) substrate, and this patterned Si(100) substrate was used as a substrate for the deposition of a gallium nitride (GaN) epilayer. Subsequently the effect that the growth pressure, the etched-hole profiles, and the etched-hole arrangement had upon the quality of the as-grown GaN was investigated. The coalescence of the as-grown GaN epilayer on the exposed Si(111) facets was observed to be enhanced with reduced growth pressure from 120 to 90 Torr. A larger Si(001) plane area at the bottom of the etched holes resulted in bidirectional GaN domains, which resulted in poor material quality. The bidirectional GaN domains were observed as two sets of six peaks via a high-resolution x-ray diffraction phi scan of the GaN(10-11) reflection. It was also shown that a triangular array of etched holes was more desirable than square arrays of etched holes for the growth high-quality and continuous GaN films.

Entropy of quasiblack holes

International Nuclear Information System (INIS)

Lemos, Jose P. S.; Zaslavskii, Oleg B.

2010-01-01

We trace the origin of the black hole entropy S, replacing a black hole by a quasiblack hole. Let the boundary of a static body approach its own gravitational radius, in such a way that a quasihorizon forms. We show that if the body is thermal with the temperature taking the Hawking value at the quasihorizon limit, it follows, in the nonextremal case, from the first law of thermodynamics that the entropy approaches the Bekenstein-Hawking value S=A/4. In this setup, the key role is played by the surface stresses on the quasihorizon and one finds that the entropy comes from the quasihorizon surface. Any distribution of matter inside the surface leads to the same universal value for the entropy in the quasihorizon limit. This can be of some help in the understanding of black hole entropy. Other similarities between black holes and quasiblack holes such as the mass formulas for both objects had been found previously. We also discuss the entropy for extremal quasiblack holes, a more subtle issue.

The effect of form pressure on the air void structure of SCC

DEFF Research Database (Denmark)

Jensen, Mikkel Vibæk; Hasholt, Marianne Tange; Geiker, Mette Rica

2005-01-01

The high workability of self-compacting concrete (SCC) invites to high casting rates. However, casting walls at high rate may result in large pressure at the bottom of the form and subsequently compression of the air voids. This paper deals with the influence of hydrostatic pressure during setting...... on the air void structure of hardened, air entrained SCC. The subject was examined through laboratory investigations of SCC with two different amounts of air entrainment. The condition in the form was simulated by using containers making it possible to cure concrete under various pressures corresponding...... to the bottom of castings of 0, 2, 4, and 6 meters height. The laboratory investigations were supplemented with data from two full-scale wall castings. The air void structure of the hardened concretes was determined on plane sections. The results indicate that the pressure related changes of the air void...

Acoustic Travel Time and Hydrostatic Pressure in Sermilik Fjord in Southeastern Greenland from 2011-08-23 to 2016-08-11 (NCEI Accession 0163212)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — These data records are time series of (1) round trip surface to bottom acoustic travel time, (2) bottom pressure and (3) bottom temperature (with the latter internal...

Measurement of the average lifetime of hadrons containing bottom quarks

International Nuclear Information System (INIS)

Klem, D.E.

1986-06-01

This thesis reports a measurement of the average lifetime of hadrons containing bottom quarks. It is based on data taken with the DELCO detector at the PEP e + e - storage ring at a center of mass energy of 29 GeV. The decays of hadrons containing bottom quarks are tagged in hadronic events by the presence of electrons with a large component of momentum transverse to the event axis. Such electrons are identified in the DELCO detector by an atmospheric pressure Cherenkov counter assisted by a lead/scintillator electromagnetic shower counter. The lifetime measured is 1.17 psec, consistent with previous measurements. This measurement, in conjunction with a limit on the non-charm branching ratio in b-decay obtained by other experiments, can be used to constrain the magnitude of the V/sub cb/ element of the Kobayashi-Maskawa matrix to the range 0.042 (+0.005 or -0.004 (stat.), +0.004 or -0.002 (sys.)), where the errors reflect the uncertainty on tau/sub b/ only and not the uncertainties in the calculations which relate the b-lifetime and the element of the Kobayashi-Maskawa matrix

Black holes without firewalls

Science.gov (United States)

Larjo, Klaus; Lowe, David A.; Thorlacius, Larus

2013-05-01

The postulates of black hole complementarity do not imply a firewall for infalling observers at a black hole horizon. The dynamics of the stretched horizon, that scrambles and reemits information, determines whether infalling observers experience anything out of the ordinary when entering a large black hole. In particular, there is no firewall if the stretched horizon degrees of freedom retain information for a time of the order of the black hole scrambling time.

The effect of particle-hole interaction on the XPS core-hole spectrum

International Nuclear Information System (INIS)

Ohno, Masahide; Sjoegren, Lennart

2004-01-01

How the effective particle-hole interaction energy, U, or the polarization effect on a secondary electron in a final two-hole one-particle (2h1p) state created by the Coster-Kronig (CK) transition can solely affect the density of the CK particle states and consequently the core-hole spectral function, is discussed. The X-ray photoelectron spectroscopy (XPS) core-hole spectrum is predominantly governed by the unperturbed initial core-hole energy relative to the zero-point energy. At the latter energy, the real part of the initial core-hole self-energy becomes zero (no relaxation energy shift) and the imaginary part (the lifetime broadening) approximately maximizes. The zero-point energy relative to the double-ionization threshold energy is governed by the ratio of U relative to the bandwidth of the CK continuum. As an example, we study the 5p XPS spectra of atomic Ra (Z=88), Th (Z=90) and U (Z=92). The spectra are interpreted in terms of the change in the unperturbed initial core-hole energy relative to the zero-point energy. We explain why in general an ab initio atomic many-body calculation can provide an overall good description of solid-state spectra predominantly governed by the atomic-like localized core-hole dynamics. We explain this in terms of the change from free atom to metal in both U and the zero-point energy (self-energy)

Over spinning a black hole?

Energy Technology Data Exchange (ETDEWEB)

Bouhmadi-Lopez, Mariam; Cardoso, Vitor; Nerozzi, Andrea; Rocha, Jorge V, E-mail: mariam.bouhmadi@ist.utl.pt, E-mail: vitor.cardoso@ist.utl.pt, E-mail: andrea.nerozzi@ist.utl.pt, E-mail: jorge.v.rocha@ist.utl.pt [CENTRA, Department de Fisica, Instituto Superior Tecnico, Av. Rovisco Pais 1, 1049 Lisboa (Portugal)

2011-09-22

A possible process to destroy a black hole consists on throwing point particles with sufficiently large angular momentum into the black hole. In the case of Kerr black holes, it was shown by Wald that particles with dangerously large angular momentum are simply not captured by the hole, and thus the event horizon is not destroyed. Here we reconsider this gedanken experiment for black holes in higher dimensions. We show that this particular way of destroying a black hole does not succeed and that Cosmic Censorship is preserved.

Cathodic protection for the bottoms of above ground storage tanks

Energy Technology Data Exchange (ETDEWEB)

Mohr, John P. [Tyco Adhesives, Norwood, MA (United States)

2004-07-01

Impressed Current Cathodic Protection has been used for many years to protect the external bottoms of above ground storage tanks. The use of a vertical deep ground bed often treated several bare steel tank bottoms by broadcasting current over a wide area. Environmental concerns and, in some countries, government regulations, have introduced the use of dielectric secondary containment liners. The dielectric liner does not allow the protective cathodic protection current to pass and causes corrosion to continue on the newly placed tank bottom. In existing tank bottoms where inadequate protection has been provided, leaks can develop. In one method of remediation, an old bottom is covered with sand and a double bottom is welded above the leaking bottom. The new bottom is welded very close to the old bottom, thus shielding the traditional cathodic protection from protecting the new bottom. These double bottoms often employ the use of dielectric liner as well. Both the liner and the double bottom often minimize the distance from the external tank bottom. The minimized space between the liner, or double bottom, and the bottom to be protected places a challenge in providing current distribution in cathodic protection systems. This study examines the practical concerns for application of impressed current cathodic protection and the types of anode materials used in these specific applications. One unique approach for an economical treatment using a conductive polymer cathodic protection method is presented. (author)

Barometric pressure transient testing applications at the Nevada Test Site: formation permeability analysis. Final report

International Nuclear Information System (INIS)

Hanson, J.M.

1984-12-01

The report evaluates previous investigations of the gas permeability of the rock surrounding emplacement holes at the Nevada Test Site. The discussion sets the framework from which the present uncertainty in gas permeability can be overcome. The usefulness of the barometric pressure testing method has been established. Flow models were used to evaluate barometric pressure transients taken at NTS holes U2fe, U19ac and U20ai. 31 refs., 103 figs., 18 tabs

Primordial black hole formation during the QCD epoch

International Nuclear Information System (INIS)

Jedamzik, K.

1997-01-01

We consider the formation of horizon-size primordial black holes (PBH close-quote s) from pre-existing density fluctuations during cosmic phase transitions. It is pointed out that the formation of PBH close-quote s should be particularly efficient during the QCD epoch due to a substantial reduction of pressure forces during adiabatic collapse, or equivalently, a significant decrease in the effective speed of sound during the color-confinement transition. Our considerations imply that for generic initial density perturbation spectra PBH mass functions are expected to exhibit a pronounced peak on the QCD-horizon mass scale ∼1M circle-dot . This mass scale is roughly coincident with the estimated masses for compact objects recently observed in our galactic halo by the MACHO Collaboration. Black holes formed during the QCD epoch may offer an attractive explanation for the origin of halo dark matter evading possibly problematic nucleosynthesis and luminosity bounds on baryonic halo dark matter. copyright 1997 The American Physical Society

A performance test of a capsule for a material irradiation in the OR holes of HANARO

International Nuclear Information System (INIS)

Cho, M. S.; Choo, K. N.; Shin, Y. T.; Sohn, J. M.; Park, S. J.; Kang, Y. H.; Kim, B. G.

2008-01-01

A test for a pressure drop and a vibration was performed to develop a material capsule for an irradiation at the OR hole in HANARO. It was analyzed before the test that a diameter of a material capsule for the OR holes should be more than 49mm by an evaluation of a flow rate and pressure drop in theory. According to this estimation, 3 kinds of mock-up capsules with a diameter of 52, 54, 56 mm were made and applied to a pressure drop test. As a result of the pressure drop test, the requirement for a pressure and a flow rate in HANARO was confirmed to be satisfied for the 3 kinds of diameters. The capsules with diameters of 54, 56mm were applied to a vibration test by taking into consideration a receptive capacity of the specimens. The capsule with a diameter of 56mm satisfied the requirement for an allowable limit of the vibration acceleration applied in HANARO. The heat transfer coefficient and the temperature on the surface of a capsule were estimated. As the temperature on the surface of the capsule was calculated to be 43.7 .deg. C, the ONB condition in HANARO was satisfied

Horizons in Matter:. Black Hole Hair Versus Null Big Bang

Science.gov (United States)

Bronnikov, K. A.; Zaslavskii, Oleg B.

It is shown that only particular kinds of matter (in terms of the "radial" pressure-to-density ratio w) can coexist with Killing horizons in black hole or cosmological space-times. Thus, for arbitrary (not necessarily spherically symmetric) static black holes, admissible are vacuum matter (w = -1, i.e. the cosmological constant or its generalization with the same value of w) and matter with certain values of w between 0 and -1, in particular a gas of disordered cosmic strings (w = -1/3). If the cosmological evolution starts from a horizon (the so-called null big bang scenarios), this horizon can coexist with vacuum matter and certain kinds of phantom matter with w ≤ -3. It is concluded that normal matter in such scenarios is entirely created from vacuum.

MELCOR simulation of long-term station blackout at Peach Bottom

International Nuclear Information System (INIS)

Madni, I.K.

1990-01-01

This paper presents the results from MELCOR (Version 1.8BC) calculations of the Long-Term Station Blackout Accident Sequence, with failure to depressurize the reactor vessel, at the Peach Bottom (BWR Mark I) plant, and presents comparisons with Source Term Code Package (STCP) calculations of the same sequence. This sequence assumes that batteries are available for six hours following loss of all power to the plant. Following battery failure, the reactor coolant system (RCS) inventory is boiled off through the relief valves by continued decay heat generation. This leads to core uncovery, heatup, clad oxidation, core degradation, relocation, and, eventually, vessel failure at high pressure. STCP has calculated the transient out to 13.5 hours after core uncovery. The results include the timing of key events, pressure and temperature response in the reactor vessel and containment, hydrogen production, and the release of source terms to the environment. 12 refs., 23 figs., 3 tabs

Ultra high hole mobilities in a pure strained Ge quantum well

International Nuclear Information System (INIS)

Mironov, O.A.; Hassan, A.H.A.; Morris, R.J.H.; Dobbie, A.; Uhlarz, M.; Chrastina, D.; Hague, J.P.; Kiatgamolchai, S.; Beanland, R.; Gabani, S.; Berkutov, I.B.; Helm, M.; Drachenko, O.; Myronov, M.; Leadley, D.R.

2014-01-01

Hole mobilities at low and room temperature (RT) have been studied for a strained sGe/SiGe heterostructure using standard Van der Pauw resistivity and Hall effect measurements. The range of magnetic field and temperatures used were − 14 T < B < + 14 T and 1.5 K < T < 300 K respectively. Using maximum entropy-mobility spectrum analysis (ME-MSA) and Bryan's algorithm mobility spectrum (BAMS) analysis, a RT two dimensional hole gas drift mobility of (3.9 ± 0.4) × 10 3 cm 2 /V s was determined for a sheet density (p s ) 9.8 × 10 10 cm −2 (by ME-MSA) and (3.9 ± 0.2) × 10 3 cm 2 /V s for a sheet density (p s ) 5.9 × 10 10 cm −2 (by BAMS). - Highlights: • Pure strained Ge channel grown by reduced pressure chemical vapor deposition • Maximum entropy-mobility spectrum analysis • Bryan's algorithm mobility spectrum analysis • High room temperature hole drift mobility of (3.9 ± 0.4) × 10 3 cm 2 /V s • Extremely high hole mobility of 1.1 × 10 6 cm 2 /V s at 12 K

Accreting Black Holes

OpenAIRE

Begelman, Mitchell C.

2014-01-01

I outline the theory of accretion onto black holes, and its application to observed phenomena such as X-ray binaries, active galactic nuclei, tidal disruption events, and gamma-ray bursts. The dynamics as well as radiative signatures of black hole accretion depend on interactions between the relatively simple black-hole spacetime and complex radiation, plasma and magnetohydrodynamical processes in the surrounding gas. I will show how transient accretion processes could provide clues to these ...

Naked black holes

International Nuclear Information System (INIS)

Horowitz, G.T.; Ross, S.F.

1997-01-01

It is shown that there are large static black holes for which all curvature invariants are small near the event horizon, yet any object which falls in experiences enormous tidal forces outside the horizon. These black holes are charged and near extremality, and exist in a wide class of theories including string theory. The implications for cosmic censorship and the black hole information puzzle are discussed. copyright 1997 The American Physical Society

Grain size engineering of bcc refractory metals: Top-down and bottom-up-Application to tungsten

International Nuclear Information System (INIS)

Kecskes, L.J.; Cho, K.C.; Dowding, R.J.; Schuster, B.E.; Valiev, R.Z.; Wei, Q.

2007-01-01

We have used two general methodologies for the production of ultrafine grained (UFG) and nanocrystalline (NC) tungsten (W) metal samples: top-down and bottom-up. In the first, Equal channel angular extrusion (ECAE), coupled with warm rolling has been used to fabricate UFG W, and high pressure torsion (HPT) was used to fabricate NC W. We demonstrate an abrupt shift in the deformation mechanism, particularly under dynamic compressive loading, in UFG and NC W. This novel deformation mechanism, a dramatic transition from a uniform deformation mode to that of localized shearing, is shared by other UFG and NC body-centerd cubic (BCC) metals. We have also conducted a series of bottom-up experiments to consolidate powdered UFG W precursors into solid bodies. The bottom-up approach relies on rapid, high-temperature consolidation, specifically designed for UFG and NC W powders. The mechanical property results from the top-down UFG and NC W were used as minimum property benchmarks to guide and design the experimental protocols and parameters for use in the bottom-up procedures. Preliminary results, showing rapid grain growth during the consolidation cycle, did not achieve full density in the W samples. Further development of high-purity W nanopowders and appropriate grain-growth inhibitors (e.g., Zener pinning) will be required to successfully produce bulk-sized UFG and NC W samples

Ballistic hole magnetic microscopy

NARCIS (Netherlands)

Haq, E.; Banerjee, T.; Siekman, M.H.; Lodder, J.C.; Jansen, R.

2005-01-01

A technique to study nanoscale spin transport of holes is presented: ballistic hole magnetic microscopy. The tip of a scanning tunneling microscope is used to inject hot electrons into a ferromagnetic heterostructure, where inelastic decay creates a distribution of electron-hole pairs.

A combined bottom-up/top-down approach to prepare a sterile injectable nanosuspension.

Science.gov (United States)

Hu, Xi; Chen, Xi; Zhang, Ling; Lin, Xia; Zhang, Yu; Tang, Xing; Wang, Yanjiao

2014-09-10

To prepare a uniform nanosuspension of strongly hydrophobic riboflavin laurate (RFL) allowing sterile filtration, physical modification (bottom-up) was combined with high-pressure homogenization (top-down) method. Unlike other bottom-up approaches, physical modification with surfactants (TPGS and PL-100) by lyophilization controlled crystallization and compensated for the poor wettability of RFL. On one hand, crystal growth and aggregation during freezing was restricted by a stabilizer-layer adsorbed on the drug surface by hydrophobic interaction. On the other hand, subsequent crystallization of drug in the sublimation process was limited to the interstitial spaces between solvent crystals. After lyophilization, modified drug with a smaller particle size and better wettability was obtained. When adding surfactant solution, water molecules passed between the hydrophilic groups of surface active molecules and activated the polymer chains allowing them to stretch into water. The coarse suspension was crushed into a nanosuspension (MP=162 nm) by high-pressure homogenization. For long term stability, lyophilization was applied again to solidify the nanosuspension (sorbitol as cryoprotectant). A slight crystal growth to about 600 nm was obtained to allow slow release for a sustained effect after muscular administration. Moreover, no paw-licking responses and very slight muscular inflammation demonstrated the excellent biocompatibility of this long-acting RFL injection. Copyright © 2014 Elsevier B.V. All rights reserved.

Black-hole driven winds

International Nuclear Information System (INIS)

Punsly, B.M.

1988-01-01

This dissertation is a study of the physical mechanism that allows a large scale magnetic field to torque a rapidly rotating, supermassive black hole. This is an interesting problem as it has been conjectured that rapidly rotating black holes are the central engines that power the observed extragalactic double radio sources. Axisymmetric solutions of the curved space-time version of Maxwell's equations in the vacuum do not torque black holes. Plasma must be introduced for the hole to mechanically couple to the field. The dynamical aspect of rotating black holes that couples the magnetic field to the hole is the following. A rotating black hole forces the external geometry of space-time to rotate (the dragging of inertial frames). Inside of the stationary limit surface, the ergosphere, all physical particle trajectories must appear to rotate in the same direction as the black hole as viewed by the stationary observers at asymptotic infinity. In the text, it is demonstrated how plasma that is created on field lines that thread both the ergosphere and the equatorial plane will be pulled by gravity toward the equator. By the aforementioned properties of the ergosphere, the disk must rotate. Consequently, the disk acts like a unipolar generator. It drives a global current system that supports the toroidal magnetic field in an outgoing, magnetically dominated wind. This wind carries energy (mainly in the form of Poynting flux) and angular momentum towards infinity. The spin down of the black hole is the ultimate source of this energy and angular momentum flux

The Mechanism and Application of Deep-Hole Precracking Blasting on Rockburst Prevention

Directory of Open Access Journals (Sweden)

Zhenhua Ouyang

2015-01-01

Full Text Available The mechanism of preventing rockburst through deep-hole precracking blasting was studied based on experimental test, numerical simulation, and field testing. The study results indicate that the deep-hole precracking could change the bursting proneness and stress state of coal-rock mass, thereby preventing the occurrence of rockburst. The bursting proneness of the whole composite structure could be weakened by the deep-hole precracking blasting. The change of stress state in the process of precracking blasting is achieved in two ways: (1 artificially break the roof apart, thus weakening the continuity of the roof strata, effectively inducing the roof caving while reducing its impact strength; and (2 the dynamic shattering and air pressure generated by the blasting can structurally change the properties of the coal-rock mass by mitigating the high stress generation and high elastic energy accumulation, thus breaking the conditions of energy transfer and rock burst occurrence.

Numerical Simulation and Optimization of Hole Spacing for Cement Grouting in Rocks

Directory of Open Access Journals (Sweden)

Ping Fu

2013-01-01

Full Text Available The fine fissures of V-diabase were the main stratigraphic that affected the effectiveness of foundation grout curtain in Dagang Mountain Hydropower Station. Thus, specialized in situ grouting tests were conducted to determine reasonable hole spacing and other parameters. Considering time variation of the rheological parameters of grout, variation of grouting pressure gradient, and evolution law of the fracture opening, numerical simulations were performed on the diffusion process of cement grouting in the fissures of the rock mass. The distribution of permeability after grouting was obtained on the basis of analysis results, and the grouting hole spacing was discussed based on the reliability analysis. A probability of optimization along with a finer optimization precision as 0.1 m could be adopted when compared with the accuracy of 0.5 m that is commonly used. The results could provide a useful reference for choosing reasonable grouting hole spacing in similar projects.

Technology of double casing tubes & a binary cycle system for hole cleaning for CBM multi-branch horizontal wells

Directory of Open Access Journals (Sweden)

Yong Yang

2017-03-01

Full Text Available At present, the aeration-assisted cutting-carrying technology is faced with complexities in the drilling of CBM multi-branch horizontal wells. For example, the aerating pressure is hardly maintained, and the borehole instability may happen. In view of these prominent problems, the technology of double casing tubes & a binary cycle system suitable for CBM multi-branch horizontal wells was developed according to the Venturi principle by means of parasitic tube insufflation which is used for well control simulation system. Then, a multiphase flow finite element model was established for the fluid-cutting particle system in this drilling condition. This technology was tested in field. Double-casing tubes cementing is adopted in this technology and a jet generator is installed at the bottom of the inner casing. In the process of drilling, the drilling fluid injected through double intermediate casing annulus is converted by the jet generator into a high-efficiency steering water jet, which, together with the water jet generated by the bit nozzle, increases the fluid returning rate in the inner annulus space. It is indicated from simulation results that the cutting-carrying effect is the best when the included angle between the nozzle of the jet generator and the vertical direction is 30°. Besides, the influential laws of cutting size, primary cycle volume, accessory cycle volume and drilling velocity on hole cleaning are figured out. It is concluded that this technology increases the flow rate of drilling fluid in annulus space, the returning rate of drilling fluid significantly and the cutting-carrying capacity. It is currently one of the effective hole cleaning technologies for CBM multi-branch horizontal wells where fresh water is taken as the drilling fluid.

Black holes are hot

International Nuclear Information System (INIS)

Gibbons, G.

1976-01-01

Recent work, which has been investigating the use of the concept of entropy with respect to gravitating systems, black holes and the universe as a whole, is discussed. The resulting theory of black holes assigns a finite temperature to them -about 10 -7 K for ordinary black holes of stellar mass -which is in complete agreement with thermodynamical concepts. It is also shown that black holes must continuously emit particles just like ordinary bodies which have a certain temperature. (U.K.)

Blob/hole formation and zonal-flow generation in the edge plasma of the JET tokamak

DEFF Research Database (Denmark)

Xu, G.S.; Naulin, Volker; Fundamenski, W.

2009-01-01

The first experimental evidence showing the connection between blob/hole formation and zonal-flow generation was obtained in the edge plasma of the JET tokamak. Holes as well as blobs are observed to be born in the edge shear layer, where zonal-flows shear off meso-scale coherent structures......, leading to disconnection of positive and negative pressure perturbations. The newly formed blobs transport azimuthal momentum up the gradient of the azimuthal flow and drive the zonal-flow shear while moving outwards. During this process energy is transferred from the meso-scale coherent structures...

Stratigraphy, structure, and some petrographic features of Tertiary volcanic rocks at the USW G-2 drill hole, Yucca Mountain, Nye County, Nevada

International Nuclear Information System (INIS)

Maldonado, F.; Koether, S.L.

1983-01-01

A continuously cored drill hole penetrated 1830.6 m of Tertiary volcanic strata comprised of the following in descending order: Paintbrush Tuff, tuffaceous beds of Calico Hills, Crater Flat Tuff, lava and flow breccia (rhyodacitic), tuff of Lithic Ridge, bedded and ash-flow tuff, lava and flow breccia bedded tuff, conglomerate and ash-flow tuff, and older tuffs of USW G-2. Comparison of unit thicknesses at USW G-2 to unit thicknesses at previously drilled holes at Yucca Mountain indicate: (1) thickening of the Paintbrush Tuff members and tuffaceous beds of Calico Hills toward the northern part of Yucca Mountain; (2) thickening of the Prow Pass Member but thinning of the Bullfrog Member and Tram unit; (3) thinning of the tuff of Lithic Ridge; (4) presence of about 280 m of lava and flow breccia not previously penetrated by any drill hole; and (5) presence of an ash-flow tuff unit at the bottom of the drill hole not previously intersected, apparently the oldest unit penetrated at Yucca Mountain to date. Petrographic features of some of the units include: (1) decrease in quartz and K-feldspar and increases in biotite and plagioclase with depth in the tuffaceous beds of Calico Hills; (2) an increase in quartz phenocrysts from the top to the bottom members of the Crater Flat Tuff; (3) a low quartz content in the tuff of Lithic Ridge, suggesting tapping of the magma chamber at quartz-poor levels; (4) a change in zeolitic alteration from heulandite to clinoptilolite to mordenite with increasing depth; (5) lavas characterized by a rhyolitic top and dacitic base, suggesting reverse compositional zoning; and (6) presence of hydrothermal mineralization in the lavas that could be related to an itrusive under Yucca Mountain or to volcanism associated with the Timber Mountain-Claim Canyon caldera complex. A fracture analysis of the core resulted in tabulation of 7848 fractures, predominately open and high angle

Hulls and structural material waste conditioning by high pressure compaction

International Nuclear Information System (INIS)

Frotscher, H.

1991-01-01

Since 1986 KfK is developing a conditioning process. Main subjects of the investigations were the development of the production technique and the planning of the most important equipments of the process under remote conditions. The process is based on an extensive program of experiments. Inactive bulks of hulls and structural material components were compacted using maximum axial pressure load of about 300 MPa. The product density as function of press force was experimentally determinated. The mechanical loads of the press and tools were estimated for the design of these equipments. The hydraulic press consists a horizontal four-cylinder press. The maximum force of the press is 25 MN. The main advantage is the modular design of the press which is open on all sides. Especially the free accessibility from top is ensured. The report also represents relevant radiological data of the alternative product. Co-60 is the dominating activity of the product due to the effects of the heat production. An amount of 10 kg hull waste or 25 kg top and bottom pieces of the spent fuel assemblies per package is already beyond the Co-60 limit of the KONRAD regulations. The nuclear thermal power of a filled container is approximately sixty times lower compared with a vitrified HLW-container. Since the product shows thermal stability beyond 200 0 C, this it is suited for a combined disposal together with vitrified HLW-containers in salt bore holes of a geological disposal. The preliminary cost evaluation is based on a reprocessing throughput of 500 t HM per year and volume reduction factor of 5.3. Accordingly there are produced 300 waste packages with hulls only or 625 units with hulls and top and bottom pieces which require 1.6 or 2.3 millions DM respectively

Intermediate-Mass Black Holes

Science.gov (United States)

Miller, M. Coleman; Colbert, E. J. M.

2004-01-01

The mathematical simplicity of black holes, combined with their links to some of the most energetic events in the universe, means that black holes are key objects for fundamental physics and astrophysics. Until recently, it was generally believed that black holes in nature appear in two broad mass ranges: stellar-mass (M~3 20 M⊙), which are produced by the core collapse of massive stars, and supermassive (M~106 1010 M⊙), which are found in the centers of galaxies and are produced by a still uncertain combination of processes. In the last few years, however, evidence has accumulated for an intermediate-mass class of black holes, with M~102 104 M⊙. If such objects exist they have important implications for the dynamics of stellar clusters, the formation of supermassive black holes, and the production and detection of gravitational waves. We review the evidence for intermediate-mass black holes and discuss future observational and theoretical work that will help clarify numerous outstanding questions about these objects.

Modeling of the effect of intentionally introduced traps on hole transport in single-crystal rubrene

KAUST Repository

Dacuñ a, Javier; Desai, Amit; Xie, Wei; Salleo, Alberto

2014-01-01

Defects have been intentionally introduced in a rubrene single crystal by means of two different mechanisms: ultraviolet ozone (UVO) exposure and x-ray irradiation. A complete drift-diffusion model based on the mobility edge (ME) concept, which takes into account asymmetries and nonuniformities in the semiconductor, is used to estimate the energetic and spatial distribution of trap states. The trap distribution for pristine devices can be decomposed into two well defined regions: a shallow region ascribed to structural disorder and a deeper region ascribed to defects. UVO and x ray increase the hole trap concentration in the semiconductor with different energetic and spatial signatures. The former creates traps near the top surface in the 0.3-0.4 eV region, while the latter induces a wider distribution of traps extending from the band edge with a spatial distribution that peaks near the top and bottom interfaces. In addition to inducing hole trap states in the transport gap, both processes are shown to reduce the mobility with respect to a pristine crystal. © 2014 American Physical Society.

Modeling of the effect of intentionally introduced traps on hole transport in single-crystal rubrene

KAUST Repository

Dacuña, Javier

2014-06-05

Defects have been intentionally introduced in a rubrene single crystal by means of two different mechanisms: ultraviolet ozone (UVO) exposure and x-ray irradiation. A complete drift-diffusion model based on the mobility edge (ME) concept, which takes into account asymmetries and nonuniformities in the semiconductor, is used to estimate the energetic and spatial distribution of trap states. The trap distribution for pristine devices can be decomposed into two well defined regions: a shallow region ascribed to structural disorder and a deeper region ascribed to defects. UVO and x ray increase the hole trap concentration in the semiconductor with different energetic and spatial signatures. The former creates traps near the top surface in the 0.3-0.4 eV region, while the latter induces a wider distribution of traps extending from the band edge with a spatial distribution that peaks near the top and bottom interfaces. In addition to inducing hole trap states in the transport gap, both processes are shown to reduce the mobility with respect to a pristine crystal. © 2014 American Physical Society.

Compression under a mechanical counter pressure space suit glove

Science.gov (United States)

Waldie, James M A.; Tanaka, Kunihiko; Tourbier, Dietmar; Webb, Paul; Jarvis, Christine W.; Hargens, Alan R.

2002-01-01

Background: Current gas-pressurized space suits are bulky stiff shells severely limiting astronaut function and capability. A mechanical counter pressure (MCP) space suit in the form of a tight elastic garment could dramatically improve extravehicular activity (EVA) dexterity, but also be advantageous in safety, cost, mass and volume. The purpose of this study was to verify that a prototype MCP glove exerts the design compression of 200 mmHg, a pressure similar to the current NASA EVA suit. Methods: Seven male subjects donned a pressure measurement array and MCP glove on the right hand, which was placed into a partial vacuum chamber. Average compression was recorded on the palm, the bottom of the middle finger, the top of the middle finger and the dorsum of the hand at pressures of 760 (ambient), 660 and 580 mmHg. The vacuum chamber was used to simulate the pressure difference between the low breathing pressure of the current NASA space suits (approximately 200 mmHg) and an unprotected hand in space. Results: At ambient conditions, the MCP glove compressed the dorsum of the hand at 203.5 +/- 22.7 mmHg, the bottom of the middle finger at 179.4 +/- 16.0 mmHg, and the top of the middle finger at 183.8 +/- 22.6 mmHg. The palm compression was significantly lower (59.6 +/- 18.8 mmHg, pglove compression with the chamber pressure reductions. Conclusions: The MCP glove compressed the dorsum of the hand and middle finger at the design pressure.

Quintessence Reissner Nordström Anti de Sitter Black Holes and Joule Thomson Effect

Science.gov (United States)

Ghaffarnejad, H.; Yaraie, E.; Farsam, M.

2018-06-01

In this work we investigate corrections of the quintessence regime of the dark energy on the Joule-Thomson (JT) effect of the Reissner Nordström anti de Sitter (RNAdS) black hole. The quintessence dark energy has equation of state as p q = ω ρ q in which -1black hole mass, we calculate inversion temperature T i of the quintessence RNAdS black hole where its cooling phase is changed to heating phase at a particular (inverse) pressure P i . Position of the inverse point { T i , P i } is determined by crossing the inverse curves with the corresponding Gibbons-Hawking temperature on the T-P plan. We determine position of the inverse point versus different numerical values of the mass M and the charge Q of the quintessence AdS RN black hole. The cooling-heating phase transition (JT effect) is happened for M > Q in which the causal singularity is still covered by the horizon. Our calculations show sensitivity of the inverse point { T i , P i } position on the T-P plan to existence of the quintessence dark energy just for large numerical values of the AdS RN black holes charge Q. In other words the quintessence dark energy dose not affect on position of the inverse point when the AdS RN black hole takes on small charges.

Black hole multiplicity at particle colliders (Do black holes radiate mainly on the brane?)

International Nuclear Information System (INIS)

Cavaglia, Marco

2003-01-01

If gravity becomes strong at the TeV scale, we may have the chance to produce black holes at particle colliders. In this Letter we revisit some phenomenological signatures of black hole production in TeV-gravity theories. We show that the bulk-to-brane ratio of black hole energy loss during the Hawking evaporation phase depends crucially on the black hole greybody factors and on the particle degrees of freedom. Since the greybody factors have not yet been calculated in the literature, and the particle content at trans-Planckian energies is not known, it is premature to claim that the black hole emits mainly on the brane. We also revisit the decay time and the multiplicity of the decay products of black hole evaporation. We give general formulae for black hole decay time and multiplicity. We find that the number of particles produced during the evaporation phase may be significantly lower than the average multiplicity which has been used in the past literature

String-Corrected Black Holes

Energy Technology Data Exchange (ETDEWEB)

Hubeny, V.

2005-01-12

We investigate the geometry of four dimensional black hole solutions in the presence of stringy higher curvature corrections to the low energy effective action. For certain supersymmetric two charge black holes these corrections drastically alter the causal structure of the solution, converting seemingly pathological null singularities into timelike singularities hidden behind a finite area horizon. We establish, analytically and numerically, that the string-corrected two-charge black hole metric has the same Penrose diagram as the extremal four-charge black hole. The higher derivative terms lead to another dramatic effect--the gravitational force exerted by a black hole on an inertial observer is no longer purely attractive. The magnitude of this effect is related to the size of the compactification manifold.

Video studies of passage by Anopheles gambiae mosquitoes through holes in a simulated bed net: effects of hole size, hole orientation and net environment.

Science.gov (United States)

Sutcliffe, James; Colborn, Kathryn L

2015-05-13

Holes in netting provide potential routes for mosquitoes to enter ITNs. Despite this, there is little information on how mosquitoes respond to holes in bed nets and how their responses are affected by hole size, shape and orientation or by ambient conditions around the net. Female Anopheles gambiae (G3) were recorded in a simulated bed net consisting of two sizes of untreated netting-covered behavioural arenas placed above and beside (to simulate the bed net roof and sides respectively) the experimenter who was a source of host cues from 'inside' the net. A round hole of 9 mm or 13 mm diameter was cut into the centre of the netting of each arena. Videos of unfed female mosquitoes in arenas were analysed for time spent flying, walking and standing still and for exit through the hole. The effects of the experimenter on temperature and relative humidity around the simulated net were also measured. Mosquitoes were significantly more active in overhead arenas than in arenas to the side. Hole passage was significantly more likely in smaller arenas than larger ones and for larger holes than smaller ones. In arenas to the side, hole passage rate through small holes was about 50% less likely than what could be explained by area alone. Passage rate through holes in overhead arenas was consistent with hole area. Temperature in arenas did not strongly reflect the experimenter's presence in the simulated net. Relative humidity and absolute humidity in overhead arenas, but not in arenas to the side, were immediately affected by experimenter presence. Higher levels of activity in overhead arenas than in arenas to the side were likely due to the rising heat and humidity plume from the experimenter. Lower than expected passage rates through smaller vertically oriented holes may have been be due to an edge effect that does not apply to horizontally oriented holes. Results suggest that current methods of assessing the importance of physical damage to ITNs may not accurately reflect

Structural differences between glycosylated, disulfide-linked heterodimeric Knob-into-Hole Fc fragment and its homodimeric Knob-Knob and Hole-Hole side products.

Science.gov (United States)

Kuglstatter, A; Stihle, M; Neumann, C; Müller, C; Schaefer, W; Klein, C; Benz, J

2017-09-01

An increasing number of bispecific therapeutic antibodies are progressing through clinical development. The Knob-into-Hole (KiH) technology uses complementary mutations in the CH3 region of the antibody Fc fragment to achieve heavy chain heterodimerization. Here we describe the X-ray crystal structures of glycosylated and disulfide-engineered heterodimeric KiH Fc fragment and its homodimeric Knob-Knob and Hole-Hole side products. The heterodimer structure confirms the KiH design principle and supports the hypothesis that glycosylation stabilizes a closed Fc conformation. Both homodimer structures show parallel Fc fragment architectures, in contrast to recently reported crystal structures of the corresponding aglycosylated Fc fragments which in the absence of disulfide mutations show an unexpected antiparallel arrangement. The glycosylated Knob-Knob Fc fragment is destabilized as indicated by variability in the relative orientation of its CH3 domains. The glycosylated Hole-Hole Fc fragment shows an unexpected intermolecular disulfide bond via the introduced Y349C Hole mutation which results in a large CH3 domain shift and a new CH3-CH3 interface. The crystal structures of glycosylated, disulfide-linked KiH Fc fragment and its Knob-Knob and Hole-Hole side products reported here will facilitate further design of highly efficient antibody heterodimerization strategies. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Exploring Jets from a Supermassive Black Hole

Science.gov (United States)

Kohler, Susanna

2018-06-01

What are the feeding and burping habits of the supermassive black holes peppering the universe? In a new study, observations of one such monster reveal more about the behavior of its powerful jets.Beams from BehemothsAcross the universe, supermassive black holes of millions to billions of solar masses lie at the centers of galaxies, gobbling up surrounding material. But not all of the gas and dust that spirals in toward a black hole is ultimately swallowed! A large fraction of it can instead be flung out into space again, in the form of enormous, powerful jets that extend for thousands or even millions of light-years in opposite directions.M87, shown in this Hubble image, is a classic example of a nearby (55 million light-years distant) supermassive black hole with a visible, collimated jet. Its counter-jet isnt seen because relativistic effects make the receding jet appear less bright. [The Hubble Heritage Team (STScI/AURA) and NASA/ESA]What causes these outflows to be tightly beamed collimated in the form of jets, rather than sprayed out in all directions? Does the pressure of the ambient medium the surrounding gas and dust that the jet is injected into play an important role? In what regions do these jets accelerate and decelerate? There are many open questions that scientists hope to understand by studying some of the active black holes with jets that live closest to us.Eyes on a Nearby GiantIn a new study led by Satomi Nakahara (The Graduate University for Advanced Studies in Japan), a team of scientists has used multifrequency Very Long Baseline Array (VLBA) and Very Long Array (VLA) images to explore jets emitted from a galaxy just 100 million light-years away: NGC 4261.This galaxys (relatively) close distance as well as the fact that were viewing it largely from the side, so we can clearly see both of its polar jets allows us to observe in detail the structure and intensity of its jets as a function of their distance from the black hole. Nakahara and

Internal structure of black holes

International Nuclear Information System (INIS)

Cvetic, Mirjam

2013-01-01

Full text: We review recent progress that sheds light on the internal structure of general black holes. We first summarize properties of general multi-charged rotating black holes both in four and five dimensions. We show that the asymptotic boundary conditions of these general asymptotically flat black holes can be modified such that a conformal symmetry emerges. These subtracted geometries preserve the thermodynamic properties of the original black holes and are of the Lifshitz type, thus describing 'a black hole in the asymptotically conical box'. Recent efforts employ solution generating techniques to construct interpolating geometries between the original black hole and their subtracted geometries. Upon lift to one dimension higher, these geometries lift to AdS 3 times a sphere, and thus provide a microscopic interpretation of the black hole entropy in terms of dual two-dimensional conformal field theory. (author)

Numerical Simulation Study on Steam-Assisted Gravity Drainage Performance in a Heavy Oil Reservoir with a Bottom Water Zone

Directory of Open Access Journals (Sweden)

Jun Ni

2017-12-01

Full Text Available In the Pikes Peak oil field near Lloydminster, Canada, a significant amount of heavy oil reserves is located in reservoirs with a bottom water zone. The properties of the bottom water zone and the operation parameters significantly affect oil production performance via the steam-assisted gravity drainage (SAGD process. Thus, in order to develop this type of heavy oil resource, a full understanding of the effects of these properties is necessary. In this study, the numerical simulation approach was applied to study the effects of properties in the bottom water zone in the SAGD process, such as the initial gas oil ratio, the thickness of the reservoir, and oil saturation of the bottom water zone. In addition, some operation parameters were studied including the injection pressure, the SAGD well pair location, and five different well patterns: (1 two corner wells, (2 triple wells, (3 downhole water sink well, (4 vertical injectors with a horizontal producer, and (5 fishbone well. The numerical simulation results suggest that the properties of the bottom water zone affect production performance extremely. First, both positive and negative effects were observed when solution gas exists in the heavy oil. Second, a logarithmical relationship was investigated between the bottom water production ratio and the thickness of the bottom water zone. Third, a non-linear relation was obtained between the oil recovery factor and oil saturation in the bottom water zone, and a peak oil recovery was achieved at the oil saturation rate of 30% in the bottom water zone. Furthermore, the operation parameters affected the heavy oil production performance. Comparison of the well patterns showed that the two corner wells and the triple wells patterns obtained the highest oil recovery factors of 74.71% and 77.19%, respectively, which are almost twice the oil recovery factors gained in the conventional SAGD process (47.84%. This indicates that the optimized SAGD process

What is black hole?

Indian Academy of Sciences (India)

First page Back Continue Last page Overview Graphics. What is black hole? Possible end phase of a star: A star is a massive, luminous ball of plasma having continuous nuclear burning. Star exhausts nuclear fuel →. White Dwarf, Neutron Star, Black Hole. Black hole's gravitational field is so powerful that even ...

Thermo-mechanical analysis for determining the optimum design of a deposition hole using FLAC3D

International Nuclear Information System (INIS)

Kwon, Sang Ki; Park, Jeong Hwa; Choi, Jong Won; Kang, Chul Hyung

2002-01-01

In this study, the vertical location of canister in a deposition hole was determined from the thermo-mechanical coupling analysis using the three-dimensional finite difference code, FLAC3D. A FISH program was made and used for the modeling for different conditions. The following conclusions could be drawn from the study. (1) The canister moves downward initially, but moves upward with time due to the thermal expansion of buffer. (2) The tunnel floor above the deposition hole remains elastic until 100 years after the emplacement of the canister if the top buffer thickness is more than 1.5 m. (3) It was found that the peak temperature decreases with the increase of the buffer and backfill thickness, when backfilling is done immediately after the emplacement. (4) Without swelling pressure, the maximum tensile stress is up to 18 MPa at 100 days after the emplacement. Since the swelling pressure from the buffer confines the thermal expansion of the canister, the mechanical stability of canister is improved with the swelling pressure. (5) When the air temperature in the tunnels is maintained at 27 .deg. C by ventilation, the peak temperature with delayed backfilling for 50 years is about 75 .deg. while it is over 90 .deg. with immediately backfilling. (6) The buffer and backfill thickness above the canister in a deposition hole should be at least 2 m based on literature review and the computer simulations

Quantum effects in black holes

International Nuclear Information System (INIS)

Frolov, V.P.

1979-01-01

A strict definition of black holes is presented and some properties with regard to their mass are enumerated. The Hawking quantum effect - the effect of vacuum instability in the black hole gravitational field, as a result of shich the black hole radiates as a heated body is analyzed. It is shown that in order to obtain results on the black hole radiation it is sufficient to predetermine the in-vacuum state at a time moment in the past, when the collapsing body has a large size, and its gravitational field can be neglected. The causes and the place of particle production by the black hole, and also the space-time inside the black hole, are considered

Assessment of capability of models for prediction of pressure drop and dryout heat flux in a heat generating particulate debris bed

International Nuclear Information System (INIS)

Kulkarni, P.P.; Nayak, A.K.; Rashid, M.; Kulenovic, R.

2009-01-01

During a severe accident in a light water reactor, the core can melt and be relocated to the lower plenum of the reactor pressure vessel. There it can form a particulate debris bed due to the possible presence of water. This bed, if not quenched in time, can lead to the failure of the pressure vessel because of the insufficient heat removal of decay heat in the debris bed. Therefore, addressing the issue of coolability behaviour of heat generating particulate debris bed is of prime importance in the framework of severe accident management strategies, particularly in case of above mentioned late phase scenario of an accident. In order to investigate the coolability behaviour of particulate debris bed, experiments were carried out at IKE test facility 'DEBRIS' on particle beds of irregularly shaped particles mixed with spheres under top- and bottom-flooding condition. The pressure drop and dryout heat flux (DHF) were measured for top- and bottom-flooding conditions. For top-flooding conditions, it was found that the pressure gradients are all smaller than the hydrostatic pressure gradient of water, indicating an important role of the counter-current interfacial shear stress of the two-phase flow. For bottom-flooding with a relatively high liquid inflow velocity, the pressure gradient increases consistently with the vapour velocity and the fluid-particle drags become important. Also, with additional forced liquid inflow from the bottom, the DHF increases dramatically. In all the cases, it was found that the DHF is significantly larger with bottom-flooding condition compared to top-flooding condition. Different models such as Lipinski, Reed, Tung and Dhir, Hu and Theophanous, and Schulenberg and Mueller have been used to predict the pressure drop characteristics and the DHF of heat generating particulate debris beds. Comparison is made among above mentioned models and experimental results for DHF and pressure drop characteristics. Considering the overall trend in

Problems of cleaning the large diameter sections of deep wells

Energy Technology Data Exchange (ETDEWEB)

Patsch, F; Gilicz, B

1966-01-01

In drilling deep wells, great importance is being given to the problem of cutting removal from the hole bottom of sections drilled by large diameter bits. The length of borehole sections drilled by 12-1/4-in. and larger bits has been more than doubled in Hungary in the course of the past 4 years. When the drilling fluid jet is struck against the borehole bottom, pressure waves are brought about which take on a crossed flow pattern and result in a retardation of cleaning of the well bottom, particularly in the case of larger bottom surfaces. In large diameter boreholes, the cleaning efficiency is being achieved by full utilization of the pump power and increased pump delivery. Friction losses in drill pipes are being reduced by using 6-in. XH pipes.

Top-down versus bottom-up processing of influence diagrams in probabilistic analysis

International Nuclear Information System (INIS)

Timmerman, R.D.; Burns, T.J.; Dodds, H.L. Jr.

1986-01-01

Recent work by Phillips et al and Selby et al has shown that influence diagram methodology can be a useful analytical tool in reactor safety studies. In some instances, an influence diagram can be used as a graphical representation of probabilistic dependence within a system or event sequence. Under these circumstances, Bayesian statistics is employed to transform the relationships depicted in the influence diagram into the correct expression for a desired marginal probability (e.g., the top node). In the references cited above, the authors demonstrated the usefulness of influence diagrams for assessing the reliability of operator performance during pressurized thermal shock transients. In addition, the use of influence diagrams identified the critical variables that had the greatest impact on operator reliability for a particular scenario (e.g., control room design, procedures, etc.). Top-down and bottom-up algorithms have emerged as the dominant methods for quantifying influence diagrams. The purpose of this paper is to demonstrate a potential error in employing the bottom-up algorithm when dealing with interdependencies

30 CFR 57.7055 - Intersecting holes.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Intersecting holes. 57.7055 Section 57.7055... Jet Piercing Drilling-Surface and Underground § 57.7055 Intersecting holes. Holes shall not be drilled where there is a danger of intersecting a misfired hole or a hole containing explosives, blasting agents...

30 CFR 56.7055 - Intersecting holes.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Intersecting holes. 56.7055 Section 56.7055... Piercing Drilling § 56.7055 Intersecting holes. Holes shall not be drilled where there is a danger of intersecting a misfired hole or a hole containing explosives blasting agents, or detonators. [56 FR 46508, Sept...

Pair of accelerated black holes in an anti-de Sitter background: The AdS C metric

International Nuclear Information System (INIS)

Dias, Oscar J.C.; Lemos, Jose P.S.

2003-01-01

The anti-de Sitter C metric (AdS C metric) is characterized by a quite interesting new feature when compared with the C metric in flat or de Sitter backgrounds. Indeed, contrary to what happens in these two last exact solutions, the AdS C metric only describes a pair of accelerated black holes if the acceleration parameter satisfies A>1/l, where l is the cosmological length. The two black holes cannot interact gravitationally and their acceleration is totally provided by the pressure exerted by a strut that pushes the black holes apart. Our analysis is based on the study of the causal structure, on the description of the solution in the AdS 4-hyperboloid in a 5D Minkowski spacetime, and on the physics of the strut. We also analyze the cases A=1/l and A<1/l that represent a single accelerated black hole in the AdS background

Critical phenomena of regular black holes in anti-de Sitter space-time

Energy Technology Data Exchange (ETDEWEB)

Fan, Zhong-Ying [Peking University, Center for High Energy Physics, Beijing (China)

2017-04-15

In General Relativity, addressing coupling to a non-linear electromagnetic field, together with a negative cosmological constant, we obtain the general static spherical symmetric black hole solution with magnetic charges, which is asymptotic to anti-de Sitter (AdS) space-times. In particular, for a degenerate case the solution becomes a Hayward-AdS black hole, which is regular everywhere in the full space-time. The existence of such a regular black hole solution preserves the weak energy condition, while the strong energy condition is violated. We then derive the first law and the Smarr formula of the black hole solution. We further discuss its thermodynamic properties and study the critical phenomena in the extended phase space where the cosmological constant is treated as a thermodynamic variable as well as the parameter associated with the non-linear electrodynamics. We obtain many interesting results such as: the Maxwell equal area law in the P-V (or S-T) diagram is violated and consequently the critical point (T{sub *},P{sub *}) of the first order small-large black hole transition does not coincide with the inflection point (T{sub c},P{sub c}) of the isotherms; the Clapeyron equation describing the coexistence curve of the Van der Waals (vdW) fluid is no longer valid; the heat capacity at constant pressure is finite at the critical point; the various exponents near the critical point are also different from those of the vdW fluid. (orig.)

Lifshitz topological black holes

International Nuclear Information System (INIS)

Mann, R.B.

2009-01-01

I find a class of black hole solutions to a (3+1) dimensional theory gravity coupled to abelian gauge fields with negative cosmological constant that has been proposed as the dual theory to a Lifshitz theory describing critical phenomena in (2+1) dimensions. These black holes are all asymptotic to a Lifshitz fixed point geometry and depend on a single parameter that determines both their area (or size) and their charge. Most of the solutions are obtained numerically, but an exact solution is also obtained for a particular value of this parameter. The thermodynamic behaviour of large black holes is almost the same regardless of genus, but differs considerably for small black holes. Screening behaviour is exhibited in the dual theory for any genus, but the critical length at which it sets in is genus-dependent for small black holes.

Black hole decay as geodesic motion

International Nuclear Information System (INIS)

Gupta, Kumar S.; Sen, Siddhartha

2003-01-01

We show that a formalism for analyzing the near-horizon conformal symmetry of Schwarzschild black holes using a scalar field probe is capable of describing black hole decay. The equation governing black hole decay can be identified as the geodesic equation in the space of black hole masses. This provides a novel geometric interpretation for the decay of black holes. Moreover, this approach predicts a precise correction term to the usual expression for the decay rate of black holes

Drilling miniature holes, Part III

Energy Technology Data Exchange (ETDEWEB)

Gillespie, L.K.

1978-07-01

Miniature components for precision electromechanical mechanisms such as switches, timers, and actuators typically require a number of small holes. Because of the precision required, the workpiece materials, and the geometry of the parts, most of these holes must be produced by conventional drilling techniques. The use of such techniques is tedious and often requires considerable trial and error to prevent drill breakage, minimize hole mislocation and variations in hole diameter. This study of eight commercial drill designs revealed that printed circuit board drills produced better locational and size repeatability than did other drills when centerdrilling was not used. Boring holes 1 mm in dia, or less, as a general rule did not improve hole location in brass or stainless steel. Hole locations of patterns of 0.66-mm holes can be maintained within 25.4-..mu..m diametral positional tolerance if setup misalignments can be eliminated. Size tolerances of +- 3.8 ..mu..m can be maintained under some conditions when drilling flat plates. While these levels of precision are possible with existing off-the-shelf drills, they may not be practical in many cases.

46 CFR 173.058 - Double bottom requirements.

Science.gov (United States)

2010-10-01

... PERTAINING TO VESSEL USE School Ships § 173.058 Double bottom requirements. Each new sailing school vessel... service must comply with the double bottom requirements in §§ 171.105 through 171.109, inclusive, of this...