WorldWideScience

Sample records for boiling nitric acid

  1. Corrosion Behavior of Ti-32Ta Alloy in Boiling Nitric Acid%高 Ta 钛合金在沸腾硝酸中的腐蚀行为

    Institute of Scientific and Technical Information of China (English)

    杨帆; 巨建辉; 毛小南; 吴金平; 杨英丽

    2014-01-01

    The anticorrosion titanium alloy Ti-32Ta was corroded evenly in boiling nitric acid of 8 mol/L, the corrosion behavior in boiling nitric acid has been researched.The chemical composition, structure and valence state of the surface passive film were analyzed by SEM, XRD and XPS.The results show that Ti-32Ta alloy corrosion in boiling nitric acid is a uniform behavior.Little effect is on the corrosion rate of the stable corrosion alloy when the fresh air is pumped into boiling nitric acid.The passive film of Ti-32Ta alloy is thinner, more compact and has better corrosion resistance than Ti-6Ta alloy.The valence state of Ti and Ta in the passive film of two alloys is the same, and the contents of Ta and Ta2 O5 in the Ti-32Ta alloy corrosion surface are higher than in the Ti-6Ta alloy.%对高Ta含量钛合金Ti-32Ta在8 mol/L沸腾硝酸溶液中进行了全浸腐蚀实验,研究了Ti-32Ta合金在沸腾硝酸中的腐蚀行为。采用扫描电子显微镜( SEM)、 X射线衍射( XRD)、 X射线衍射光电子能谱( XPS)等分析方法对钛合金腐蚀表面的钝化膜进行了成分、组织结构及合金价态分析。结果表明: Ti-32Ta合金在沸腾硝酸溶液中呈现均匀腐蚀行为,在介质中通入一定流量的新鲜空气对合金稳定腐蚀阶段的腐蚀速率影响不大。与Ti-6Ta合金相比, Ti-32Ta合金腐蚀后形成的钝化膜更薄更致密,耐蚀性能更好。两种合金腐蚀钝化膜中Ti和Ta的价态组成相同, Ti-32Ta合金腐蚀表面Ta及Ta2 O5的含量高于Ti-6Ta合金腐蚀表面。

  2. Corrosion studies in fuel element reprocessing environments containing nitric acid

    Energy Technology Data Exchange (ETDEWEB)

    Beavers, J A; White, R R; Berry, W E; Griess, J C

    1982-04-01

    Nitric acid is universally used in aqueous fuel element reprocessing plants; however, in the processing scheme being developed by the Consolidated Fuel Reprocessing Program, some of the equipment will be exposed to nitric acid under conditions not previously encountered in fuel element reprocessing plants. A previous report presented corrosion data obtained in hyperazeotropic nitric acid and in concentrated magnesium nitrate solutions used in its preparation. The results presented in this report are concerned with the following: (1) corrosion of titanium in nitric acid; (2) corrosion of nickel-base alloys in a nitric acid-hydrofluoric acid solution; (3) the formation of Cr(VI), which enhances corrosion, in nitric acid solutions; and (4) corrosion of mechanical pipe connectors in nitric acid. The results show that the corrosion rate of titanium increased with the refreshment rate of boiling nitric acid, but the effect diminished rapidly as the temperature decreased. The addition of iodic acid inhibited attack. Also, up to 200 ppM of fluoride in 70% HNO/sub 3/ had no major effect on the corrosion of either titanium or tantalum. In boiling 8 M HNO/sub 3/-0.05 M HF, Inconel 671 was more resistant than Inconel 690, but both alloys experienced end-grain attack. In the case of Inconel 671, heat treatment was very important; annealed and quenched material was much more resistant than furnace-cooled material.The rate of oxidation of Cr(III) to Cr(VI) increased significantly as the nitric acid concentration increased, and certain forms of ruthenium in the solution seemed to accelerate the rate of formation. Mechanical connectors of T-304L stainless steel experienced end-grain attack on the exposed pipe ends, and seal rings of both stainless steel and a titanium alloy (6% Al-4% V) underwent heavy attack in boiling 8 M HNO/sub 3/.

  3. Alternative to Nitric Acid Passivation

    Science.gov (United States)

    Kessel, Kurt R.

    2016-01-01

    Corrosion is an extensive problem that affects the National Aeronautics and Space Administration (NASA) and European Space Agency (ESA). The deleterious effects of corrosion result in steep costs, asset downtime affecting mission readiness, and safety risks to personnel. It is vital to reduce corrosion costs and risks in a sustainable manner. The primary objective of this effort is to qualify citric acid as an environmentally-preferable alternative to nitric acid for passivation of stainless steel alloys.

  4. The Oxidation of Hydrazine by Nitric Acid

    Energy Technology Data Exchange (ETDEWEB)

    Karraker, D.G.

    2001-07-02

    Hydrazine nitrate-nitric acid solutions are used in the ion exchange process for separating Pu-238 and Np-237 and have been found to dissolve plutonium metal in a manner advantageous to SRP metal recovery operations. Laboratory tests on the stability of hydrazine in nitric acid solutions were performed to obtain accurate data, and the results of these tests are reported here. These tests provide sufficient information to specify temperature control for hydrazine-nitric acid solutions in plant processes.

  5. Alternative to Nitric Acid Passivation

    Science.gov (United States)

    Kessel, Kurt R.

    2015-01-01

    The Ground Systems Development and Operations (GSDO) Program at NASA John F. Kennedy Space Center (KSC), Florida, has the primary objective of modernizing and transforming the launch and range complex at KSC to benefit current and future NASA programs along with other emerging users. Described as the launch support and infrastructure modernization program in the NASA Authorization Act of 2010, the GSDO Program will develop and implement shared infrastructure and process improvements to provide more flexible, affordable, and responsive capabilities to a multi-user community. In support of NASA and the GSDO Program, the objective of this project is to qualify citric acid as an environmentally-preferable alternative to nitric acid for passivation of stainless steel alloys. This project is a direct follow-on to United Space Alliance (USA) work at KSC to optimize the parameters for the use of citric acid and verify effectiveness. This project will build off of the USA study to further evaluate citric acids effectiveness and suitability for corrosion protection of a number of stainless steels alloys used by NASA, the Department of Defense (DoD), and the European Space Agency (ESA).

  6. Citric Acid Alternative to Nitric Acid Passivation

    Science.gov (United States)

    Lewis, Pattie L. (Compiler)

    2013-01-01

    The Ground Systems Development and Operations GSDO) Program at NASA John F. Kennedy Space Center (KSC) has the primary objective of modernizing and transforming the launch and range complex at KSC to benefit current and future NASA programs along with other emerging users. Described as the launch support and infrastructure modernization program in the NASA Authorization Act of 2010, the GSDO Program will develop and implement shared infrastructure and process improvements to provide more flexible, affordable, and responsive capabilities to a multi-user community. In support of the GSDO Program, the purpose of this project is to demonstratevalidate citric acid as a passivation agent for stainless steel. Successful completion of this project will result in citric acid being qualified for use as an environmentally preferable alternative to nitric acid for passivation of stainless steel alloys in NASA and DoD applications.

  7. Ti35合金在沸腾硝酸中钝化膜及过渡层形成及组成分析%Passive Film and Transition Layer on Ti35 Alloy after Exposure to Boiling Nitric Acid Solution

    Institute of Scientific and Technical Information of China (English)

    郭荻子; 杨英丽; 赵彬; 赵恒章; 吴金平; 苏航标

    2015-01-01

    The composition and phase constitution of the passive film and the transition layer on Ti35 alloy after immersion corrosion test in 8 mol/L boiling nitric acid were investigated.By using atomic force microscope(AFM), scanning electron microscopy ( SEM) , X ray diffractometer ( XRD) and X ray photoelectron spectroscopy ( XPS) , the corrosion behavior and the structure of the oxide film of Ti35 corrosion samples were investigated.The results show that Ta atoms preferentially react with nitrate.The passive film consists of TiO2 and Ta2 O5 , and the evolution of these oxides is step by step.And corrosion resistance to nitric acid of titanium alloy can effectively improve by adding element Ta.%研究了Ti35合金在8 mol/L 沸腾浓硝酸中腐蚀240 h后表面钝化膜及过渡层的相结构。采用扫描电子显微镜(SEM)、原子力显微镜(AFM)、 X射线衍射(XRD)和X射线光电子能谱(XPS)对Ti35合金腐蚀后样品的钝化膜和过渡层形貌、相结构等进行分析。研究结果表明, Ta原子优先与硝酸反应,钝化膜最终产物TiO2和Ta2 O5是通过逐步的化学反应形成的, Ta元素的加入能有效改善钛合金的耐硝酸腐蚀性能。

  8. Electrochemical Behavior of Aluminum in Nitric Acid

    Institute of Scientific and Technical Information of China (English)

    CHEN; Hui; ZHU; Li-yang; LIN; Ru-shan; TAN; Hong-bin; HE; Hui

    2013-01-01

    Aluminum is one of cladding materials for nuclear fuel,it is important to investigate the electrolytic dissolution of aluminum in nitric acid.The electrochemical impedance spectroscopy,polarization curve and cyclic voltammetry cure of anodic aluminum electrode in nitric acid under various conditions were collected(Fig.1).It turns out,under steady state,the thickness of the passivated film of aluminum

  9. Modeling acid-gas generation from boiling chloride brines

    Directory of Open Access Journals (Sweden)

    Sonnenthal Eric

    2009-11-01

    Full Text Available Abstract Background This study investigates the generation of HCl and other acid gases from boiling calcium chloride dominated waters at atmospheric pressure, primarily using numerical modeling. The main focus of this investigation relates to the long-term geologic disposal of nuclear waste at Yucca Mountain, Nevada, where pore waters around waste-emplacement tunnels are expected to undergo boiling and evaporative concentration as a result of the heat released by spent nuclear fuel. Processes that are modeled include boiling of highly concentrated solutions, gas transport, and gas condensation accompanied by the dissociation of acid gases, causing low-pH condensate. Results Simple calculations are first carried out to evaluate condensate pH as a function of HCl gas fugacity and condensed water fraction for a vapor equilibrated with saturated calcium chloride brine at 50-150°C and 1 bar. The distillation of a calcium-chloride-dominated brine is then simulated with a reactive transport model using a brine composition representative of partially evaporated calcium-rich pore waters at Yucca Mountain. Results show a significant increase in boiling temperature from evaporative concentration, as well as low pH in condensates, particularly for dynamic systems where partial condensation takes place, which result in enrichment of HCl in condensates. These results are in qualitative agreement with experimental data from other studies. Conclusion The combination of reactive transport with multicomponent brine chemistry to study evaporation, boiling, and the potential for acid gas generation at the proposed Yucca Mountain repository is seen as an improvement relative to previously applied simpler batch evaporation models. This approach allows the evaluation of thermal, hydrological, and chemical (THC processes in a coupled manner, and modeling of settings much more relevant to actual field conditions than the distillation experiment considered. The actual

  10. Alternative to Nitric Acid Passivation Project Overview

    Science.gov (United States)

    Lewis, Pattie L.

    2013-01-01

    The standard practice for protection of stainless steel is a process called passivation. This procedure results in the formation of a metal oxide layer to prevent corrosion. Typical passivation procedures call for the use of nitric acid which exhibits excellent corrosion performance; however, there are a number of environmental, worker safety, and operational issues associated with its use. The longtime military specification for the passivation of stainless steel was cancelled in favor of newer specifications which allow for the use of citric acid in place of nitric acid. Citric acid offers a variety of benefits that include increased safety for personnel, reduced environmental impact, and reduced operational costs. There have been few studies, however, to determine whether citric acid is an acceptable alternative for NASA and DoD. This paper details activities to date including development of the joint test plan, on-going and planned testing, and preliminary results.

  11. Speciation in aqueous solutions of nitric acid.

    Science.gov (United States)

    Hlushak, S; Simonin, J P; De Sio, S; Bernard, O; Ruas, A; Pochon, P; Jan, S; Moisy, P

    2013-02-28

    In this study, speciation in aqueous solutions of nitric acid at 25 °C was assessed in two independent ways. First, Raman experiments were carried out and interpreted in terms of free nitrate ions, ion pairs and neutral HNO(3) molecules. In parallel, a model was developed to account for the formation of these two kinds of pairs. It was based on an extension of the binding mean spherical approximation (BiMSA), or associative MSA (AMSA), in which the size and the charge of the ions in the chemical pair may differ from those of the free ions. A simultaneous fit of the osmotic coefficient and of the proportion of free ions (obtained from Raman spectroscopy experiments) led to an estimation of the speciation in nitric acid solutions. The result obtained using this procedure was compared with the estimation obtained from the Raman experiments.

  12. Metastable Nitric Acid Trihydrate in Ice Clouds

    Science.gov (United States)

    Weiss, Fabian; Kubel, Frank; Gálvez, Oscar; Hölzel, Markus; Parker, Stewart F.; Baloh, Philipp; Iannarelli, Riccardo; Rossi, Michel J.; Grothe, Hinrich

    2016-04-01

    The composition of high altitude ice clouds is still a matter of intense discussion. The constituents in question are ice and nitric acid hydrates. The identification and formation mechanisms, however, are still unknown but are essential to understand atmospheric processing such as the seasonal ozone depletion in the lower polar stratosphere or the radiation balance of planet Earth. We found conclusive evidence for a long-predicted phase, which has been named alpha nitric acid trihydrate (alpha-NAT). This phase has been proven by combination of X-ray and neutron diffraction experiments allowing a convincing structure solution. Additionally, vibrational spectra (infrared and inelastic neutron scattering) were recorded and compared with theoretical calculations. A strong affinity between water ice and alpha-NAT has been found, which explains the experimental spectra and the phase transition kinetics essential for identification in the atmosphere. On the basis of our results, we propose a new three-step mechanism for NAT-formation in high altitude ice clouds. F. Weiss et al. Angew. Chem. Int. Ed. 2016, accepted, DOI:10.1002/anie.201510841

  13. Adverse experiences with nitric acid at the Savannah River Site

    Energy Technology Data Exchange (ETDEWEB)

    Durant, W.S.; Craig, D.K.; Vitacco, M.J.; McCormick, J.A.

    1991-06-01

    Nitric acid is used routinely at the Savannah River Site (SRS) in many processes. However, the site has experienced a number of adverse situations in handling nitric acid. These have ranged from minor injuries to personnel to significant explosions. This document compiles many of these events and includes discussions of process upsets, fires, injuries, and toxic effects of nitric acid and its decomposition products. The purpose of the publication is to apprise those using the acid that it is a potentially dangerous material and can react in many ways as demonstrated by SRS experience. 10 refs.

  14. Nitric acid vapor removal by activated, impregnated carbons

    Energy Technology Data Exchange (ETDEWEB)

    Wood, G.O.

    1996-12-31

    Laboratory and industrial workers can be exposed to vapors of nitric acid, especially in accidents, such as spills. Nitric acid can also be a product of incineration for energy production or waste (e.g., CW agent) disposal. Activated carbons containing impregnants for enhancing vapor and gas removal have been tested for effectiveness in removing vapors of nitric acid from air. The nitric acid vapor was generated from concentrated acid solutions and detected by trapping in a water bubbler for pH measurements. Both low and moderate relative humidity conditions were used. All carbons were effective at vapor contact times representative of air-purifying respirator use. One surprising observation was the desorption of low levels of ammonia from impregnated carbons. This was apparently due to residual ammonia from the impregnation processes.

  15. Acute chemical pneumonitis caused by nitric acid inhalation: case report

    Energy Technology Data Exchange (ETDEWEB)

    Choe, Hyung Shim; Lee, In Jae; Ko, Eun Young; Lee, Jae Young; Kim, Hyun Beom; Hwang, Dae Hyun; Lee, Kwan Seop; Lee, Yul; Bae, Sang Hoon [Hallym University Sacred Heart Hospital, Anyang (Korea, Republic of)

    2003-06-01

    Chemical pneumonitis induced by nitric acid inhalation is a rare clinical condition. The previously reported radiologic findings of this disease include acute permeability pulmonary edema, delayed bronchiolitis obliterans, and bronchiectasis. In very few published rare radiologic reports has this disease manifested as acute alveolar injury; we report a case of acute chemical pneumonitis induced by nitric acid inhalation which at radiography manifested as bilateral perihilar consolidation and ground-glass attenuation, suggesting acute alveolar injury.

  16. Diamagnetism and Strucure of Nitric Acid-Treated Bulk Polyethylene

    OpenAIRE

    Ania, F.; Baltá Calleja, F. J.; Cagiao, M.E.

    1982-01-01

    An alternative procedure to examine the nature of the end product of nitric-acid-treated bulk polyethylene involving the measurement of the diamagnetic susceptibility is reported. This simple non-destructive method complements previous results obtained by means of IR spectroscopy. Thus after selectively removing the surface layer of the polyethylene lamellae with nitric acid (t > 50h) the diamagnetic susceptibility substantially decreases to values wich are consistent with tilted paraff...

  17. Extraction of nitric acid, uranyl nitrate, and bismuth nitrate from aqueous nitric acid solutions with CMPO

    Energy Technology Data Exchange (ETDEWEB)

    Spencer, B.B.

    1995-08-01

    DOE sponsored development of the transuranium extraction (TRUEX) process for removing actinides from radioactive wastes. The solvent is a mixture of CMPO and TBP. Since the extraction characteristics of CMPO are not as well understood as those of TBP, the extraction of nitric acid, uranyl nitrate, and bismuth nitrate with CMPO (dissolved in n-dodecane) were studied. Results indicate that CMPO extracts nitric acid with a 1:1 stoichiometry; equilibrium constant is 2. 660{plus_minus}0.092 at 25 C, and extraction enthalpy is -5. 46{plus_minus}0.46 kcal/mol. Slope analysis indicates that uranyl nitrate extracts with a mixed equilibria of 1:1 and 2:1 stoichiometries in nearly equal proportion. Equil. constant of the 2: 1 extraction was 1.213 {times} 10{sup 6}{plus_minus}3.56 {times} 10{sup 4} at 25 C; reaction enthalpy was -9.610{plus_minus}0.594 kcal/mol. Nitration complexation constant is 8.412{plus_minus}0.579, with an enthalpy of -10.72{plus_minus}1.87 kcal/mol. Bismuth nitrate also extracts with a mixed equilibria of (perhaps) 1:1 and 2:1 stoichiometries. A 2:1 extraction equilibrium and a nitrate complexation adequately model the data. Kinetics and enthalpies were also measured.

  18. Sludge batch 9 simulant runs using the nitric-glycolic acid flowsheet

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, D. P. [Savannah River Site (SRS), Aiken, SC (United States); Williams, M. S. [Savannah River Site (SRS), Aiken, SC (United States); Brandenburg, C. H. [Savannah River Site (SRS), Aiken, SC (United States); Luther, M. C. [Savannah River Site (SRS), Aiken, SC (United States); Newell, J. D. [Savannah River Site (SRS), Aiken, SC (United States); Woodham, W. H. [Savannah River Site (SRS), Aiken, SC (United States)

    2016-11-01

    Testing was completed to develop a Sludge Batch 9 (SB9) nitric-glycolic acid chemical process flowsheet for the Defense Waste Processing Facility’s (DWPF) Chemical Process Cell (CPC). CPC simulations were completed using SB9 sludge simulant, Strip Effluent Feed Tank (SEFT) simulant and Precipitate Reactor Feed Tank (PRFT) simulant. Ten sludge-only Sludge Receipt and Adjustment Tank (SRAT) cycles and four SRAT/Slurry Mix Evaporator (SME) cycles, and one actual SB9 sludge (SRAT/SME cycle) were completed. As has been demonstrated in over 100 simulations, the replacement of formic acid with glycolic acid virtually eliminates the CPC’s largest flammability hazards, hydrogen and ammonia. Recommended processing conditions are summarized in section 3.5.1. Testing demonstrated that the interim chemistry and Reduction/Oxidation (REDOX) equations are sufficient to predict the composition of DWPF SRAT product and SME product. Additional reports will finalize the chemistry and REDOX equations. Additional testing developed an antifoam strategy to minimize the hexamethyldisiloxane (HMDSO) peak at boiling, while controlling foam based on testing with simulant and actual waste. Implementation of the nitric-glycolic acid flowsheet in DWPF is recommended. This flowsheet not only eliminates the hydrogen and ammonia hazards but will lead to shorter processing times, higher elemental mercury recovery, and more concentrated SRAT and SME products. The steady pH profile is expected to provide flexibility in processing the high volume of strip effluent expected once the Salt Waste Processing Facility starts up.

  19. Simulated dry deposition of nitric acid near forest edges

    NARCIS (Netherlands)

    DeJong, JJM; Klaassen, W; Jong, J.J.M. de

    1997-01-01

    Dry deposition is simulated to understand and generalize observations of enhanced deposition of air pollution near forest edges. Nitric acid is taken as an example as its deposition velocity is often assumed to be determined by turbulent transport only. The simulations are based on the micro-meteoro

  20. Nitric acid trihydrate (NAT) in polar stratospheric clouds.

    Science.gov (United States)

    Voigt, C; Schreiner, J; Kohlmann, A; Zink, P; Mauersberger, K; Larsen, N; Deshler, T; Kröger, C; Rosen, J; Adriani, A; Cairo, F; Di Donfrancesco, G; Viterbini, M; Ovarlez, J; Ovarlez, H; David, C; Dörnbrack, A

    2000-12-01

    A comprehensive investigation of polar stratospheric clouds was performed on 25 January 2000 with instruments onboard a balloon gondola flown from Kiruna, Sweden. Cloud layers were repeatedly encountered at altitudes between 20 and 24 kilometers over a wide range of atmospheric temperatures (185 to 197 kelvin). Particle composition analysis showed that a large fraction of the cloud layers was composed of nitric acid trihydrate (NAT) particles, containing water and nitric acid at a molar ratio of 3:1; this confirmed that these long-sought solid crystals exist well above ice formation temperatures. The presence of NAT particles enhances the potential for chlorine activation with subsequent ozone destruction in polar regions, particularly in early and late winter.

  1. Alternative to Nitric Acid for Passivation of Stainless Steel Alloys

    Science.gov (United States)

    Lewis, Pattie L.; Kolody, Mark; Curran, Jerry

    2013-01-01

    Corrosion is an extensive problem that affects the Department of Defense (DoD) and National Aeronautics and Space Administration (NASA). The deleterious effects of corrosion result in steep costs, asset downtime affecting mission readiness, and safety risks to personnel. Consequently, it is vital to reduce corrosion costs and risks in a sustainable manner. The DoD and NASA have numerous structures and equipment that are fabricated from stainless steel. The standard practice for protection of stainless steel is a process called passivation. Typical passivation procedures call for the use of nitric acid; however, there are a number of environmental, worker safety, and operational issues associated with its use. Citric acid offers a variety of benefits including increased safety for personnel, reduced environmental impact, and reduced operational cost. DoD and NASA agreed to collaborate to validate citric acid as an acceptable passivating agent for stainless steel. This paper details our investigation of prior work developing the citric acid passivation process, development of the test plan, optimization of the process for specific stainless steel alloys, ongoing and planned testing to elucidate the process' resistance to corrosion in comparison to nitric acid, and preliminary results.

  2. Corrosion investigations on zircaloy-4 and titanium dissolver materials for MOX fuel dissolution in concentrated nitric acid containing fluoride ions

    Science.gov (United States)

    Jayaraj, J.; Krishnaveni, P.; Krishna, D. Nanda Gopala; Mallika, C.; Mudali, U. Kamachi

    2016-05-01

    Aqueous reprocessing of plutonium-rich mixed oxide fuels require fluoride as a dissolution catalyst in boiling nitric acid for an effective dissolution of the spent fuel. High corrosion rates were obtained for the candidate dissolver materials zircaloy-4 (Zr-4) and commercial pure titanium (CP-Ti grade 2) in boiling 11.5 M HNO3 + 0.05 M NaF. Complexing the fluoride ions either with Al(NO3)3 or ZrO(NO3)2 aided in decreasing the corrosion rates of Zr-4 and CP-Ti. From the obtained corrosion rates it is concluded that CP-Ti is a better dissolver material than Zr-4 for extended service life in boiling 11.5 M HNO3 + 0.05 M NaF, when complexed with 0.15 M ZrO(NO3)2. XPS analysis confirmed the presence of TiO2 and absence of fluoride on the surface of CP-Ti samples, indicating that effective complexation had occurred in solution leading to passivation of the metal and imparting high corrosion resistance.

  3. Reduction Rates for Higher Americium Oxidation States in Nitric Acid

    Energy Technology Data Exchange (ETDEWEB)

    Grimes, Travis Shane [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mincher, Bruce Jay [Idaho National Lab. (INL), Idaho Falls, ID (United States); Schmitt, Nicholas C [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-09-30

    The stability of hexavalent americium was measured using multiple americium concentrations and nitric acid concentrations after contact with the strong oxidant sodium bismuthate. Contrary to our hypotheses Am(VI) was not reduced faster at higher americium concentrations, and the reduction was only zero-order at short time scales. Attempts to model the reduction kinetics using zero order kinetic models showed Am(VI) reduction in nitric acid is more complex than the autoreduction processes reported by others in perchloric acid. The classical zero-order reduction of Am(VI) was found here only for short times on the order of a few hours. We did show that the rate of Am(V) production was less than the rate of Am(VI) reduction, indicating that some Am(VI) undergoes two electron-reduction to Am(IV). We also monitored the Am(VI) reduction in contact with the organic diluent dodecane. A direct comparison of these results with those in the absence of the organic diluent showed the reduction rates for Am(VI) were not statistically different for both systems. Additional americium oxidations conducted in the presence of Ce(IV)/Ce(III) ions showed that Am(VI) is reduced without the typical growth of Am(V) observed in the systems sans Ce ion. This was an interesting result which suggests a potential new reduction/oxidation pathway for Am in the presence of Ce; however, these results were very preliminary, and will require additional experiments to understand the mechanism by which this occurs. Overall, these studies have shown that hexavalent americium is fundamentally stable enough in nitric acid to run a separations process. However, the complicated nature of the reduction pathways based on the system components is far from being rigorously understood.

  4. Nitric acid adsorption on ice at environmental temperatures

    Science.gov (United States)

    Laird, Susan Kay

    1998-12-01

    Nitric acid has become an important pollutant in areas which depend on snowpack melt for their water supply. The adsorption of HNO3 on the ice surface was investigated at [-]20oC using artificial snow packed into glass columns and exposed to nitric acid vapor in a flow system. It was observed that, given sufficient acid vapor, HNO3 would adsorb in multilayers on the ice, with the bulk of the acid remaining near the input face. With time, molecules from this high-concentration would slowly diffuse down the column, mainly along the ice surface. The surface diffusion coefficient, D, was calculated from both the average linear migration distance, /langle x/rangle, and Fick's First Law to be 3.5×10-7 cm2/sec. The vapor pressure was calculated from Fick's First Law to be 2.3([/pm]0.3)×10-7 torr. Desorption was found to be of zero order and the energy of desorption at [-]20oC was calculated from an Arrhenius-type equation to be 88.8([/pm]0.1) kJ/mol. This means that the HNO3 will tend to stay on the ice surface in a snowpack.

  5. Nitric acid: modeling osmotic coefficients and acid-base dissociation using the BIMSA theory.

    Science.gov (United States)

    Ruas, Alexandre; Pochon, Patrick; Simonin, Jean-Pierre; Moisy, Philippe

    2010-11-14

    This work is aimed at a description of the thermodynamic properties of highly concentrated aqueous solutions of nitric acid salts at 25 °C within the binding mean spherical approximation (BIMSA) theory. The predictive capability of this model was examined. First, Raman spectroscopy was used to study the proportion of associated nitric acid as a function of concentration. The corresponding apparent association constant values were compared with literature values. Besides, the BIMSA model, taking into account complex formation, was used to represent literature experimental osmotic coefficient variation with concentration. This theoretical description led to an assessment of the degree of association. The so calculated amount of associated nitric acid coincides accurately with our Raman experimental results up to a high concentration of acid.

  6. Nitric acid: modeling osmotic coefficients and acid-base dissociation using the BIMSA theory

    Energy Technology Data Exchange (ETDEWEB)

    Ruas, A.; Pochon, P.; Moisy, Ph. [CEA Marcoule, Nucl Energy Div, RadioChem and Proc Dept, F-30207 Bagnols Sur Ceze (France); Simonin, J. P. [Univ Paris 06, CNRS, UMR 7195, Lab PECSA, F-75252 Paris 05, (France)

    2010-07-01

    This work is aimed at a description of the thermodynamic properties of highly concentrated aqueous solutions of nitric acid salts at 25 C within the binding mean spherical approximation (BIMSA) theory. The predictive capability of this model was examined. First, Raman spectroscopy was used to study the proportion of associated nitric acid as a function of concentration. The corresponding apparent association constant values were compared with literature values. Besides, the BIMSA model, taking into account complex formation, was used to represent literature experimental osmotic coefficient variation with concentration. This theoretical description led to an assessment of the degree of association. The so calculated amount of associated nitric acid coincides accurately with our Raman experimental results up to a high concentration of acid. (authors)

  7. Energy integration of nitric acid production using pinch methodology

    Directory of Open Access Journals (Sweden)

    Ivaniš Gorica R.

    2015-01-01

    Full Text Available Pinch methodology was applied to the heat exchangers network (HEN synthesis of nitric acid production. The integration is analyzed in two ways, and the results are presented as two different solutions: (i the first solution is based on the original heat transfer equipment arrangement, (ii in order to eliminate the shortages of the first solution the second HEN was obtained using process simulation with optimized process parameters. Optimized HEN, with new arrangement of heat exchangers, gave good results in energy and process optimization. [Projekat Ministarstva nauke Republike Srbije, br. P172063

  8. Separation of thorium and uranium in nitric acid solution using silica based anion exchange resin.

    Science.gov (United States)

    Chen, Yanliang; Wei, Yuezhou; He, Linfeng; Tang, Fangdong

    2016-09-30

    To separate thorium and uranium in nitric acid solution using anion exchange process, a strong base silica-based anion exchange resin (SiPyR-N4) was synthesized. Batch experiments were conducted and the separation factor of thorium and uranium in 9M nitric acid was about 10. Ion exchange chromatography was applied to separate thorium and uranium in different ratios. Uranium could be eluted by 9M nitric acid and thorium was eluted by 0.1M nitric acid. It was proved that thorium and uranium can be separated and recovered successfully by this method.

  9. Nitrosation and nitration of fulvic acid, peat and coal with nitric acid

    Science.gov (United States)

    Thorn, Kevin A.; Cox, Larry G.

    2016-01-01

    Nitrohumic acids, produced from base extraction of coals and peats oxidized with nitric acid, have received considerable attention as soil ammendments in agriculture. The nitration chemistry however is incompletely understood. Moreover, there is a need to understand the reaction of nitric acid with natural organic matter (NOM) in general, in the context of a variety of environmental and biogeochemical processes. Suwannee River NOM, Suwannee River fulvic acid, and Pahokee Peat fulvic acid were treated with 15N-labeled nitric acid at concentrations ranging from 15% to 22% and analyzed by liquid and solid state 15N NMR spectroscopy. Bulk Pahokee peat and Illinois #6 coal were also treated with nitric acid, at 29% and 40% respectively, and analyzed by solid state 15N NMR spectroscopy. In addition to nitro groups from nitration of aromatic carbon, the 15N NMR spectra of all five samples exhibited peaks attributable to nitrosation reactions. These include nitrosophenol peaks in the peat fulvic acid and Suwannee River samples, from nitrosation of phenolic rings, and N-nitroso groups in the peat samples, from nitrosation of secondary amides or amines, the latter consistent with the peat samples having the highest naturally abundant nitrogen contents. Peaks attributable to Beckmann and secondary reactions of the initially formed oximes were present in all spectra, including primary amide, secondary amide, lactam, and nitrile nitrogens. The degree of secondary reaction product formation resulting from nitrosation reactions appeared to correlate inversely with the 13C aromaticities of the samples. The nitrosation reactions are most plausibly effected by nitrous acid formed from the reduction of nitric acid by oxidizable substrates in the NOM and coal samples.

  10. Nitrosation and Nitration of Fulvic Acid, Peat and Coal with Nitric Acid.

    Directory of Open Access Journals (Sweden)

    Kevin A Thorn

    Full Text Available Nitrohumic acids, produced from base extraction of coals and peats oxidized with nitric acid, have received considerable attention as soil ammendments in agriculture. The nitration chemistry however is incompletely understood. Moreover, there is a need to understand the reaction of nitric acid with natural organic matter (NOM in general, in the context of a variety of environmental and biogeochemical processes. Suwannee River NOM, Suwannee River fulvic acid, and Pahokee Peat fulvic acid were treated with 15N-labeled nitric acid at concentrations ranging from 15% to 22% and analyzed by liquid and solid state 15N NMR spectroscopy. Bulk Pahokee peat and Illinois #6 coal were also treated with nitric acid, at 29% and 40% respectively, and analyzed by solid state 15N NMR spectroscopy. In addition to nitro groups from nitration of aromatic carbon, the 15N NMR spectra of all five samples exhibited peaks attributable to nitrosation reactions. These include nitrosophenol peaks in the peat fulvic acid and Suwannee River samples, from nitrosation of phenolic rings, and N-nitroso groups in the peat samples, from nitrosation of secondary amides or amines, the latter consistent with the peat samples having the highest naturally abundant nitrogen contents. Peaks attributable to Beckmann and secondary reactions of the initially formed oximes were present in all spectra, including primary amide, secondary amide, lactam, and nitrile nitrogens. The degree of secondary reaction product formation resulting from nitrosation reactions appeared to correlate inversely with the 13C aromaticities of the samples. The nitrosation reactions are most plausibly effected by nitrous acid formed from the reduction of nitric acid by oxidizable substrates in the NOM and coal samples.

  11. Impact of scaling on the nitric-glycolic acid flowsheet

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, D. [Savannah River Site (SRS), Aiken, SC (United States)

    2016-02-01

    Savannah River Remediation (SRR) is considering using glycolic acid as a replacement for formic acid in Sludge Receipt and Adjustment Tank (SRAT) processing in the Defense Waste Processing Facility (DWPF). Catalytic decomposition of formic acid is responsible for the generation of hydrogen, a potentially flammable gas, during processing. To prevent the formation of a flammable mixture in the offgas, an air purge is used to dilute the hydrogen concentration below the 60% of the Composite Lower Flammability Limit (CLFL). The offgas is continuously monitored for hydrogen using Gas Chromatographs (GCs). Since formic acid is much more volatile and toxic than glycolic acid, a formic acid spill would lead to the release of much larger quantities to the environment. Switching from formic acid to glycolic acid is expected to eliminate the hydrogen flammability hazard leading to lower air purges, thus downgrading of Safety Significant GCs to Process Support GCs, and minimizing the consequence of a glycolic acid tank leak in DWPF. Overall this leads to a reduction in process operation costs and an increase in safety margin. Experiments were completed at three different scales to demonstrate that the nitric-glycolic acid flowsheet scales from the 4-L lab scale to the 22-L bench scale and 220-L engineering scale. Ten process demonstrations of the sludge-only flowsheet for SRAT and Slurry Mix Evaporator (SME) cycles were performed using Sludge Batch 8 (SB8)-Tank 40 simulant. No Actinide Removal Process (ARP) product or strip effluent was added during the runs. Six experiments were completed at the 4-L scale, two experiments were completed at the 22-L scale, and two experiments were completed at the 220-L scale. Experiments completed at the 4-L scale (100 and 110% acid stoichiometry) were repeated at the 22-L and 220-L scale for scale comparisons.

  12. Improvement effect on corrosion under heat flux in nitric acid solutions of anti-IGC stainless steel and high Cr-W-Si Ni base RW alloy

    Energy Technology Data Exchange (ETDEWEB)

    Doi, Masamitsu; Kiuchi, Kiyoshi; Yano, Masaya; Sekiyama, Yoshio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-03-01

    In the advanced purex reprocessing equipment, the higher corrosion resistance is required for materials because of the high corrosive environment caused from the thermodynamic decomposition of boiling nitric acid. The authors group has been developed the two types of new corrosion resistant materials for application to the reprocessing equipment. One is the type 304ULC stainless steel with controlled microstructure and decreased minor elements (EB-SAR). The other is the nickel base alloy with the ability of forming stable oxide film by addition of Cr, W and Si (RW alloy). In this study, the heat transfer tubes applied in diminished pressure was postulated. In addition to the dominant factors of heat conducting corrosion by the nitric acid solution, the effect of the heat flux and the concentration of the corrosive vanadium ions were investigated. (author)

  13. 46 CFR 151.50-80 - Nitric acid (70% or less).

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Nitric acid (70% or less). 151.50-80 Section 151.50-80 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES BARGES CARRYING BULK LIQUID HAZARDOUS MATERIAL CARGOES Special Requirements § 151.50-80 Nitric acid (70% or...

  14. Research on the Stability of Dimethyl Hydroxylamine-methyl Hydrazinein Nitric Acid Medium

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    By the means of the comparison of the extraction of PU(Ⅲ) and plutonium in nitric acid mediumcontaining dimethyl hydroxylamine-methyl hydrazine and the analysis of the percent content of PU(Ⅳ) inthe system, the stability of dimethyl hydroxylamine-methyl hydrazine in nitric acid medium is

  15. Biomass to fuels : Upgrading of flash pyrolysis oil by reactive distillation using a high boiling alcohol and acid catalysts

    NARCIS (Netherlands)

    Mahfud, F.H.; Melian Cabrera, I.V.; Manurung, R.M.; Heeres, H.J.

    2007-01-01

    We here report our studies on the upgrading of flash pyrolysis oil using an improved alcohol treatment method. The method consists of treating pyrolysis oil with a high boiling alcohol like n-butanol in the presence of a (solid) acid catalyst at 323-353 K under reduced pressure (<10 kPa). Using this

  16. Effect of Nitric Acid Concentrations on Synthesis and Stability of Maghemite Nanoparticles Suspension

    Directory of Open Access Journals (Sweden)

    Irwan Nurdin

    2014-01-01

    Full Text Available Maghemite (γ-Fe2O3 nanoparticles have been synthesized using a chemical coprecipitation method at different nitric acid concentrations as an oxidizing agent. Characterization of all samples performed by several techniques including X-ray diffraction (XRD, transmission electron microscopy (TEM, alternating gradient magnetometry (AGM, thermogravimetric analysis (TGA, dynamic light scattering (DLS, and zeta potential. The XRD patterns confirmed that the particles were maghemite. The crystallite size of all samples decreases with the increasing concentration of nitric acid. TEM observation showed that the particles have spherical morphology with narrow particle size distribution. The particles showed superparamagnetic behavior with decreased magnetization values at the increasing concentration of nitric acid. TGA measurement showed that the stability temperature decreases with the increasing concentration of nitric acid. DLS measurement showed that the hydrodynamic particle sizes decrease with the increasing concentration of nitric acid. Zeta potential values show a decrease with the increasing concentration of nitric acid. The increasing concentration of nitric acid in synthesis of maghemite nanoparticles produced smaller size particles, lower magnetization, better thermal stability, and more stable maghemite nanoparticles suspension.

  17. Effect of nitric acid concentrations on synthesis and stability of maghemite nanoparticles suspension.

    Science.gov (United States)

    Nurdin, Irwan; Johan, Mohd Rafie; Yaacob, Iskandar Idris; Ang, Bee Chin

    2014-01-01

    Maghemite (γ-Fe2O3) nanoparticles have been synthesized using a chemical coprecipitation method at different nitric acid concentrations as an oxidizing agent. Characterization of all samples performed by several techniques including X-ray diffraction (XRD), transmission electron microscopy (TEM), alternating gradient magnetometry (AGM), thermogravimetric analysis (TGA), dynamic light scattering (DLS), and zeta potential. The XRD patterns confirmed that the particles were maghemite. The crystallite size of all samples decreases with the increasing concentration of nitric acid. TEM observation showed that the particles have spherical morphology with narrow particle size distribution. The particles showed superparamagnetic behavior with decreased magnetization values at the increasing concentration of nitric acid. TGA measurement showed that the stability temperature decreases with the increasing concentration of nitric acid. DLS measurement showed that the hydrodynamic particle sizes decrease with the increasing concentration of nitric acid. Zeta potential values show a decrease with the increasing concentration of nitric acid. The increasing concentration of nitric acid in synthesis of maghemite nanoparticles produced smaller size particles, lower magnetization, better thermal stability, and more stable maghemite nanoparticles suspension.

  18. Omega-3 fatty acids improve psychomotor performance via mechanism not related to nitric acid production

    Directory of Open Access Journals (Sweden)

    Marwan S. M. Al-Nimer

    2012-01-01

    Full Text Available Omega-3 fatty acids (ω-3FAs are essential polyunsaturated fats that protect the brain from cognitive impairment. It increases the activity of endothelial nitric oxide synthetase (eNOS and thereby increases the nitric acid (NO production. This study aimed to explore the effect of ω-3FAs on psychomotor performance and to relate this effect to the reactive nitrogen species. This study was conducted in Department of Pharmacology, College of Medicine, Al-Mustansiriya University in Baghdad, Iraq. Twenty healthy subjects, allocated randomly from medical college students, were participated in the single blind clinical trial. Participants were divided into two groups, each of ten subjects to receive either placebo or (ω-3FAs (750 mg single oral dose daily for 5 days. They were asked to perform psychomotor performance before and after 5 days of treatment, and venous blood was obtained for determination of serum nitric oxide (NO and peroxynitrite (ONOO. ω-3FAs treated group was significantly different from placebo-treated group in reducing choice and motor reaction times as well as the critical flicker frequency threshold. The serum levels of NO and ONOO in ω-3FAs-treated group did not significantly differ from placebo-treated group. Short term supplementation of ω-3FAs improves the psychomotor performance in young healthy subjects via a mechanism not related to the production of nitric oxide production. Inflorescence is a panicle few flowered and fruit is a capsule. The data of the results obtained were presented and discussed.

  19. Thermal Hazard Evaluation of Lauroyl Peroxide Mixed with Nitric Acid

    Directory of Open Access Journals (Sweden)

    Chi-Min Shu

    2012-07-01

    Full Text Available Many thermal runaway incidents have been caused by organic peroxides due to the peroxy group, –O–O–, which is essentially unstable and active. Lauroyl peroxide (LPO is also sensitive to thermal sources and is incompatible with many materials, such as acids, bases, metals, and ions. From the thermal decomposition reaction of various concentrations of nitric acid (HNO3 (from lower to higher concentrations with LPO, experimental data were obtained as to its exothermic onset temperature (T0, heat of decomposition (ΔHd, isothermal time to maximum rate (TMRiso, and other safety parameters exclusively for loss prevention of runaway reactions and thermal explosions. As a novel finding, LPO mixed with HNO3 can produce the detonation product of 1-nitrododecane. We used differential scanning calorimetry (DSC, thermal activity monitor III (TAM III, and gas chromatography/mass spectrometer (GC/MS analyses of the reactivity for LPO and itself mixed with HNO3 to corroborate the decomposition reactions and reaction mechanisms in these investigations.

  20. Proteomic Investigation of Protein Profile Changes and Amino Acid Residue Level Modification in Cooked Lamb Meat: The Effect of Boiling.

    Science.gov (United States)

    Yu, Tzer-Yang; Morton, James D; Clerens, Stefan; Dyer, Jolon M

    2015-10-21

    Hydrothermal treatment (heating in water) is a common method of general food processing and preparation. For red-meat-based foods, boiling is common; however, how the molecular level effects of this treatment correlate to the overall food properties is not yet well-understood. The effects of differing boiling times on lamb meat and the resultant cooking water were here examined through proteomic evaluation. The longer boiling time was found to result in increased protein aggregation involving particularly proteins such as glyceraldehyde-3-phosphate dehydrogenase, as well as truncation in proteins such as in α-actinin-2. Heat-induced protein backbone cleavage was observed adjacent to aspartic acid and asparagine residues. Side-chain modifications of amino acid residues resulting from the heating, including oxidation of phenylalanine and formation of carboxyethyllysine, were characterized in the cooked samples. Actin and myoglobin bands from the cooked meat per se remained visible on sodium dodecyl sulfate-polyacrylamide gel electrophoresis, even after significant cooking time. These proteins were also found to be the major source of observed heat-induced modifications. This study provides new insights into molecular-level modifications occurring in lamb meat proteins during boiling and a protein chemistry basis for better understanding the effect of this common treatment on the nutritional and functional properties of red-meat-based foods.

  1. Nitric acid trihydrate (NAT formation at low NAT supersaturations

    Directory of Open Access Journals (Sweden)

    C. Voigt

    2004-12-01

    Full Text Available A polar stratospheric cloud (PSC was observed on 6 February 2003 in the Arctic stratosphere by in-situ measurements onboard the high-altitude research aircraft Geophysica. Low number densities (~10−4 cm−3 of nitric acid (HNO3 containing particles – probably NAT – with diameters up to 6 µm were measured at altitudes between 18 and 20 km. These particles have the potential to grow further and to remove HNO3 from the stratosphere, thereby enhancing polar ozone loss. Interestingly, the NAT particles formed in less than a day at temperatures T>TNAT−3.5 K, just slightly below the NAT equilibrium temperature TNAT. This unique measurement of PSC formation at extremely low NAT saturation ratios (SNAT≤11 constrains current NAT nucleation theories. In particular, NAT formation on ice can for certain be excluded. Conversely, we suggest that meteoritic particles may be favorable candidates for triggering nucleation of NAT at the observed low number densities.

  2. Moessbauer Spectroscopic Studies of {sup 237}Np in frozen nitric acid solution

    Energy Technology Data Exchange (ETDEWEB)

    Nakada, M; Wang, J; Kitazawa, T; Takahashi, M; Takeda, M; Masaki, N M; Yamashita, T [Department of Materials Science, Japan Atomic Energy Research Institute (JAERI, present JAEA: Japan Atomic Energy Agency), Tokai, Naka, Ibaraki 319-1195 (Japan); Tsutsui, S, E-mail: wangjh@dicp.ac.c [Advanced Science Research Center, JAERI, Tokai, Naka, Ibaraki 319-1195 (Japan)

    2010-03-01

    We applied Moessbauer spectroscopy to {sup 237}Np in nitric acid solutions to study chemical states. Sample solutions were adjusted to 50 mg/ml of Np(V) and Np(VI) concentration in 0.6 M nitric acid solutions. These solutions were put into original designed containers for samples and mounted to sample holders. The values of isomer shift (IS, relative to NpAl{sub 2}) of Np(V) and Np(VI) in 0.6 M nitric acid were -17.4(1) and -37.2(3) mm/s at about 10 K, respectively. It was found that Np(V) had 7 coordination number and Np(VI) had 8 in nitric acid solutions from values of IS.

  3. HIRDLS/Aura Level 3 Nitric Acid (HNO3) Zonal Fourier Coefficients V007

    Data.gov (United States)

    National Aeronautics and Space Administration — The "HIRDLS/Aura Level 3 Nitric Acid (HNO3) Zonal Fourier Coefficients" version 7 data product (H3ZFCHNO3) contains the entire mission (~3 years) of HIRDLS data...

  4. Research on the Stability of Diethyl Hydroxylamine in Nitric Acid Medium

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    By the means of the comparison of the extraction of PU(Ⅲ,Ⅳ) and plutonium in the aqueous Phasecontaining salting-free agent, the stability of diethyl hydroxylamine in nitric acid medium is investigated.

  5. Disposition and transportation of surplus radioactive low specific activity nitric acid. Volume 1, Environmental Assessment

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    DOE is deactivating the PUREX plant at Hanford; this will involve the disposition of about 692,000 liters (183,000 gallons) of surplus nitric acid contaminated with low levels of U and other radionuclides. The nitric acid, designated as low specific activity, is stored in 4 storage tanks at PUREX. Five principal alternatives were evaluated: transfer for reuse (sale to BNF plc), no action, continued storage in Hanford upgraded or new facility, consolidation of DOE surplus acid, and processing the LSA nitric acid as waste. The transfer to BNF plc is the preferred alternative. From the analysis, it is concluded that the proposed disposition and transportation of the acid does not constitute a major federal action significantly affecting the quality of the human environment within the meaning of NEPA; therefore an environmental impact statement is not required.

  6. Proton transfer reactions between nitric acid and acetone, hydroxyacetone, acetaldehyde and benzaldehyde in the solid phase.

    Science.gov (United States)

    Lasne, Jérôme; Laffon, Carine; Parent, Philippe

    2012-12-01

    The heterogeneous and homogeneous reactions of acetone, hydroxyacetone, acetaldehyde and benzaldehyde with solid nitric acid (HNO(3)) films have been studied with Reflection-Absorption Infrared Spectroscopy (RAIRS) under Ultra-High Vacuum (UHV) conditions in the 90-170 K temperature range. In the bulk or at the surface of the films, nitric acid transfers its proton to the carbonyl function of the organic molecules, producing protonated acetone-H(+), hydroxyacetone-H(+), acetaldehyde-H(+) and benzaldehyde-H(+), and nitrate anions NO(3)(-), a reaction not observed when nitric acid is previously hydrated [J. Lasne, C. Laffon and Ph. Parent, Phys. Chem. Chem. Phys., 2012, 14, 697]. This provides a molecular-scale description of the carbonyl protonation reaction in an acid medium, the first step of the acid-catalyzed condensation of carbonyl compounds, fuelling the growth of secondary organic aerosols (SOA) in the atmosphere.

  7. Laboratory studies of 2H evaporator scale dissolution in dilute nitric acid

    Energy Technology Data Exchange (ETDEWEB)

    Oji, L.

    2014-09-23

    The rate of 2H evaporator scale solids dissolution in dilute nitric acid has been experimentally evaluated under laboratory conditions in the SRNL shielded cells. The 2H scale sample used for the dissolution study came from the bottom of the evaporator cone section and the wall section of the evaporator cone. The accumulation rate of aluminum and silicon, assumed to be the two principal elemental constituents of the 2H evaporator scale aluminosilicate mineral, were monitored in solution. Aluminum and silicon concentration changes, with heating time at a constant oven temperature of 90 deg C, were used to ascertain the extent of dissolution of the 2H evaporator scale mineral. The 2H evaporator scale solids, assumed to be composed of mostly aluminosilicate mineral, readily dissolves in 1.5 and 1.25 M dilute nitric acid solutions yielding principal elemental components of aluminum and silicon in solution. The 2H scale dissolution rate constant, based on aluminum accumulation in 1.5 and 1.25 M dilute nitric acid solution are, respectively, 9.21E-04 ± 6.39E-04 min{sup -1} and 1.07E-03 ± 7.51E-05 min{sup -1}. Silicon accumulation rate in solution does track the aluminum accumulation profile during the first few minutes of scale dissolution. It however diverges towards the end of the scale dissolution. This divergence therefore means the aluminum-to-silicon ratio in the first phase of the scale dissolution (non-steady state conditions) is different from the ratio towards the end of the scale dissolution. Possible causes of this change in silicon accumulation in solution as the scale dissolution progresses may include silicon precipitation from solution or the 2H evaporator scale is a heterogeneous mixture of aluminosilicate minerals with several impurities. The average half-life for the decomposition of the 2H evaporator scale mineral in 1.5 M nitric acid is 12.5 hours, while the half-life for the decomposition of the 2H evaporator scale in 1.25 M nitric acid is 10

  8. DISSOLUTION OF PLUTONIUM METAL IN 8-10 M NITRIC ACID

    Energy Technology Data Exchange (ETDEWEB)

    Rudisill, T.; Pierce, R.

    2012-02-21

    The H-Canyon facility will be used to dissolve Pu metal for subsequent purification and conversion to plutonium dioxide (PuO{sub 2}) using Phase II of HB-Line. To support the new mission, the development of a Pu metal dissolution flowsheet which utilizes concentrated (8-10 M) nitric acid (HNO{sub 3}) solutions containing potassium fluoride (KF) is required. Dissolution of Pu metal in concentrated HNO{sub 3} is desired to eliminate the need to adjust the solution acidity prior to purification by anion exchange. The preferred flowsheet would use 8-10 M HNO{sub 3}, 0.015-0.07 M KF, and 0.5-1.0 g/L Gd to dissolve the Pu up to 6.75 g/L. An alternate flowsheet would use 8-10 M HNO{sub 3}, 0.1-0.2 M KF, and 1-2 g/L B to dissolve the Pu. The targeted average Pu metal dissolution rate is 20 mg/min-cm{sup 2}, which is sufficient to dissolve a 'standard' 2250-g Pu metal button in 24 h. Plutonium metal dissolution rate measurements showed that if Gd is used as the nuclear poison, the optimum dissolution conditions occur in 10 M HNO{sub 3}, 0.04-0.05 M KF, and 0.5-1.0 g/L Gd at 112 to 116 C (boiling). These conditions will result in an estimated Pu metal dissolution rate of {approx}11-15 mg/min-cm{sup 2} and will result in dissolution times of 36-48 h for standard buttons. The recommended minimum and maximum KF concentrations are 0.03 M and 0.07 M, respectively. The maximum KF concentration is dictated by a potential room-temperature Pu-Gd-F precipitation issue at low Pu concentrations. The purpose of the experimental work described in this report was two-fold. Initially a series of screening experiments was performed to measure the dissolution rate of Pu metal as functions of the HNO{sub 3}, KF, and Gd or B concentrations. The objective of the screening tests was to propose optimized conditions for subsequent flowsheet demonstration tests. Based on the rate measurements, this study found that optimal dissolution conditions in solutions containing 0.5-1.0 g/L Gd

  9. Effects of Nitric Acid Concentration on the Stability of Alumina Sols

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Alumina sols with a mlar ratio of 1: 50 between aluminum sec- butoxide ( ASB ) and H2 O werefabricated by adding various amounts of nitric acid.The particle shape, zeta potential, polydispersity and effective particle size of alumina sol were examined by a TEM, a zeta PALS granularity analyzer and a zetaPALS zeta potential analyzer, respectively.By analyzing the change of zeta potential and double- layer thickness with nitric acid concentration, the potential energy curves of colloidal particles were mapped on the basis of DLVO theory, and the effects of nitric acid concentration on the stability of alumina sols were intensively studied.The results show that for the alumina sols with a mol ratio of 1: 50 between ASB and H2 O, the total interaction energy of the colloidal particle is at a maximum when the nitric acid concentration is 0.22 mol/ L.Therefore, the stability of the colloid reaches optimum at the nitric acid concentration of 0.22 mol/L.

  10. Changes of Petroleum Acid Distribution Characterized by FT-ICR MS in Heavy Acidic Crude Oil after True Boiling Point Distillation

    Institute of Scientific and Technical Information of China (English)

    Liu Yingrong; Zhang Qundan; Wang Wei; Liu Zelong; Zhu Xinyi; Tian Songbai

    2014-01-01

    The molecular transformations of carboxylic acids in heavy acidic SL crude before and after true boiling point distillation were examined by ultra-high resolution negative-ion electrospray ionization (ESI) Fourier transform ion cyclo-tron resonance mass spectrometry (FT-ICR MS). The acid class (heteroatom number), type (z numbers) and carbon number distributions were positively characterized. It was found out that the total acid number (TAN) of SL crude decreased after true boiling point distillation, and the abundance of O2 class in mass spectra was also found to be reduced from 67.6%to 34.5%in SL TBP mixed crude as measured by MS spectra, indicating to a potential carboxylic acid decomposition. However, it was interesting that the carboxylic acids type distribution in both oils was almost the same although their relative abundance in SL TBP mixed crude turned to be much lower, suggesting that various petroleum carboxylic acid types have the similar thermal decomposition reaction behavior. Furthermore, for each O2 type of acids in SL TBP mixed crude, the abundance of carboxylic acids with carbon number higher than 35 was reduced greatly, especially for those with carbon number higher than 60, the mass peaks of which were nearly totally removed, indicating that the large carboxylic acid molecules in heavy fractions decomposed more signiifcantly because of longer heating time during the true boiling point distillation process. As a result, the reduction of TAN may be caused by the thermal decomposition of carboxylic acids especially those with high carbon number, suggesting that quick distillation or much lower pressure is required to avoid the thermal decomposition.

  11. Batch salicylic acid nitration by nitric acid/acetic acid mixture under isothermal, isoperibolic and adiabatic conditions.

    Science.gov (United States)

    Andreozzi, R; Canterino, M; Caprio, V; Di Somma, I; Sanchirico, R

    2006-12-01

    Runaway phenomena and thermal explosions can originate during the nitration of salicylic acid by means of a nitric acid/acetic acid mixture when the thermal control is lost, mainly as a result of the formation and thermal decomposition of picric acid. The prediction of the behaviour of this system is thus of great importance in view of possible industrial applications and the need to avoid the occurrence of unwanted dangerous events. During a previous investigation a model was developed to simulate its behaviour when the starting concentration of the substrate is too low, thus, preventing the precipitation of poor soluble intermediates. In this work this model is extended to deal with more concentrated systems even in case of a solid phase separating during the process. To this purpose the previously assessed dependence of the solubility of 3-nitro and 5-nitrosalicylic acids upon temperature and nitric acid concentration is included in the model. It is assumed that when 3-nitro and 5-nitrosalicylic acids are partially suspended in the reacting medium a kinetic regime of "dissolution with reaction" is established; that is, the redissolution of these species is a fast process compared to the successive nitration to give dinitroderivatives. Good results are obtained in the comparison of the experimental data with those calculated both in isoperibolic and adiabatic conditions when the revised model is used.

  12. Preparation of nitric humic acid by catalytic oxidation from Guizhou coal with catalysts

    Institute of Scientific and Technical Information of China (English)

    Yang Zhiyuan; Gong Liang; Ran Pan

    2012-01-01

    Nitric humic acid was prepared by catalytic oxidation between nitric acid and Guizhou coal,with added catalysts.We investigated catalytic oxidation processes and the factors that affect the reactions.The effects of different catalysts,including NiSO4 support on active carbon (AC-NiSO4),NiSO4 support on silicon dioxide (SiO2-NiSO4),composites of SO42-/Fe2O3,Zr-iron and vanadium-iron composite were studied.As well.we investigated nitric humic acid yields and the chemical structure of products by element analysis,FT-IR and E4/E6 (an absorbance ratio at wavelengths of 465 and 665 nm of humic acid alkaline extraction solutions).The results show that the catalytic oxidation reaction with added catalysts can increase humic acid yields by 18.7%,16.36%,12.94%,5.61% and 8.59%,respectively.The highest yield of humic acid,i.e.,36.0%,was obtained with AC-NiSO4 as the catalyst.The amounts of C and H decreased with the amount of nitrogen.The increase in the E4/E6 ratio in catalytic oxidation of (Guizhou) coal shows that small molecular weights and high yields of nitric humic acid can be obtained by catalytic oxidation reactions.

  13. Observation of gaseous nitric acid production at a high-energy proton accelerator facility

    CERN Document Server

    Kanda, Y; Nakajima, H

    2005-01-01

    High-energy protons and neutrons produce a variety of radionuclides as well as noxious and oxidative gases, such as ozone and nitric acid, in the air mainly through the nuclear spallation of atmospheric elements. Samples were collected from the surfaces of magnets, walls, and floors in the neutrino beamline tunnel and the target station of the KEK 12-GeV proton synchrotron facility by wiping surfaces with filter paper. Considerably good correlations were found between the amounts of nitrate and tritium and between those of nitrate and /sup 7/Be. This finding gives evidence that at high-energy proton facilities, nitric acid is produced in the radiolysis of air in beam- loss regions. Also, the nitric acid on the surfaces was found to be desorbed and tended to be more uniform throughout the tunnel due to air circulation. The magnitude of diminishing from the surfaces was in the order of tritium>nitrate>/sup 7/Be1).

  14. TESTING OF 304L STAINLESS STEEL IN NITRIC ACID ENVIRONMENTS WITH FLUORIDES AND CHLORIDES

    Energy Technology Data Exchange (ETDEWEB)

    Mickalonis, J.

    2010-10-04

    Impure radioactive material processed in nitric acid solutions resulted in the presence of chlorides in a dissolver fabricated from 304L stainless steel. An experimental program was conducted to study the effects of chloride in nitric acid/fluoride solutions on the corrosion of 304L stainless steel. The test variables included temperature (80, 95, and 110 C) and the concentrations of nitric acid (6, 12, and 14 M), fluoride (0.01, 0.1, and 0.2 M) and chloride (100, 350, 1000, and 2000 ppm). The impact of welding was also investigated. Results showed that the chloride concentration alone was not a dominant variable affecting the corrosion, but rather the interaction of chloride with fluoride significantly affected corrosion.

  15. OPTIMAL CONTROL OF AUTOCLAVE START MODE IN THE PRODUCTION OF NITRIC ACID

    OpenAIRE

    Ладієва, Леся Ростиславівна; Ширма, А. В.

    2015-01-01

    The algorithm of optimal control of autoclave start mode in the production of nitric acid is proposed. By optimality criterion is selected minimum time-autoclave at preset mode with the restriction on the concentration of nitric acid. End time start mode is entered on the terminal part of the cost function. The method of penalties and a gradient procedure is used to solve the problem. The applied algorithm is allowed to bring an autoclave at a given technological regime.Keywords: production o...

  16. Stabilization and Solidification of Nitric Acid Effluent Waste at Y-12

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Dileep [Argonne National Lab. (ANL), Argonne, IL (United States); Lorenzo-Martin, Cinta [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-12-16

    Consolidated Nuclear Security, LLC (CNS) at the Y-12 plant is investigating approaches for the treatment (stabilization and solidification) of a nitric acid waste effluent that contains uranium. Because the pH of the waste stream is 1-2, it is a difficult waste stream to treat and stabilize by a standard cement-based process. Alternative waste forms are being considered. In this regard, Ceramicrete technology, developed at Argonne National Laboratory, is being explored as an option to solidify and stabilize the nitric acid effluent wastes.

  17. Coextraction of uranium(VI) form nitric acid solutions by N,N—diethyldecanamide and TBP

    Institute of Scientific and Technical Information of China (English)

    SunGuo-Xin; SunSi-Xiu; 等

    1997-01-01

    The partition of uranium(VI) between nitric acid and N,N-diethydecanamide,C9H19CON(C2H5)2,(DEDEA)in kerosene has been investigated at various concentrations of nitric acid,extractant and slating -out agent LiNO3.The mechanism of extraction is discussed in the light of the results obtained.The effect of TBP on the extraction of uranium(VI) with DEDEA has also been considered.There is apparent synergism between these two extractants at low concentration of TBP;however,at higher concentration,distributioin ratio decreases.

  18. Material compatibility evaluation for DWPF nitric-glycolic acid-literature review

    Energy Technology Data Exchange (ETDEWEB)

    Mickalonis, J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Skidmore, E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2013-06-01

    Glycolic acid is being evaluated as an alternative for formic and nitric acid in the DWPF flowsheet. Demonstration testing and modeling for this new flowsheet has shown that glycolic acid and glycolate has a potential to remain in certain streams generated during the production of the nuclear waste glass. A literature review was conducted to assess the impact of glycolic acid on the corrosion of the materials of construction for the DWPF facility as well as facilities downstream which may have residual glycolic acid and glycolates present. The literature data was limited to solutions containing principally glycolic acid.

  19. Gamma radiolytic stability of CyMe4BTBP and the effect of nitric acid

    Directory of Open Access Journals (Sweden)

    Schmidt Holger

    2015-12-01

    Full Text Available The highly selective nitrogen donor ligand CyMe4BTBP for An(III separation by solvent extraction was irradiated in a 60Co γ-source under varying conditions. Organic solutions of 10 mmol/L ligand in 1-octanol were contacted with different concentrations of nitric acid to observe the influence of an aqueous phase during irradiation. In subsequent liquid-liquid extraction experiments, distribution ratios of 241Am and 152Eu were determined. Distribution ratios decreased with increasing absorbed dose when irradiation was performed in the absence of nitric acid. With addition of nitric acid, initial distribution ratios remained constant over the whole examined dose range up to 300 kGy. For qualitative determination of radiolysis products, HPLC-MS measurements were performed. The protective effect of nitric acid was confirmed, since in samples irradiated with acid contact, no degradation products were observed, but only addition products of the 1-octanol molecule to the CyMe4BTBP molecule.

  20. TWOPOT: a computer model of the two-pot extractive distillation concept for nitric acid

    Energy Technology Data Exchange (ETDEWEB)

    Jubin, R.T.; Holland, W.D.; Counce, R.M.; Beckwith, D.R.

    1985-05-01

    A mathematical model, TWOPOT, of the ''two-pot'' extractive distillation concept for nitric acid concentration has been developed. Prediction from a computer simulation using this model shows excellent agreement with the experimental data. This model is recommended for use in the design of large-scale, similar-purpose equipment. 9 refs., 15 figs., 2 tabs.

  1. Synthesis and bioactivity of novel nitric oxide-releasing ursolic acid derivatives

    Institute of Scientific and Technical Information of China (English)

    Li Chen; Wen Qiu; Jia Tang; Zhi Feng Wang; Shu Ying He

    2011-01-01

    A series of furoxan-based novel nitric oxide-donating ursolic acid (UA) derivatives (7a-f) were synthesized, and their cytotoxic activities against HepG2 cells in vitro were evaluated by MTT method. It was found that 7a-d and 7f showed more potent cytotoxic activities than control 5-fluorouracil and UA.

  2. Continuous wet denuder measurements of atmospheric nitric and nitrous acids during the 1999 Atlanta Supersite

    NARCIS (Netherlands)

    Genfa, Z.; Slanina, J.; Boring, C.B.; Jongejan, A.C.; Purnendu, K.D.

    2003-01-01

    Two different measurement methods for atmospheric nitric and nitrous acid during the Atlanta Supersite study are described and compared. Both approaches combined wet denuder collection coupled to ion chromatographic analysis. One of these utilized a rotating wet annular denuder maintained indoor wit

  3. ExoMol molecular line lists: XI The spectrum of nitric acid

    CERN Document Server

    Pavlyuchko, Anatoly I; Tennyson, Jonathan

    2015-01-01

    Nitric acid is a possible biomarker in the atmospheres of exoplanets. An accurate line list of rotational and rotational-vibrational transitions is computed for nitric acid (HNO$_3$). This line list covers wavelengths longer than 1.42 $\\mu$m (0 - 7000 cm$^{-1}$) and temperatures up to 500 K. The line list is computed using a hybrid variational -- perturbation theory and empirically tuned potential energy and dipole surfaces. It comprises almost 7 billion transitions involving rotations up to $J=100$. Comparisons with spectra from the HITRAN and PNNL databases demonstrate the accuracy of our calculations. Synthetic spectra of water - nitric acid mixturessuggest that nitric acid has features at 7.5 and 11.25 $\\mu$m that are capable of providing a clear signature for HNO$_3$; the feature at 11.25 $\\mu$m is particularly promising. Partition functions plus full line lists of transitions are made available in an electronic form as supplementary data to the article and at www.exomol.com.

  4. White Paper on Potential Hazards Associated with Contaminated Cheesecloth Exposed to Nitric Acid Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Hypes, Philip A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-09-20

    This white paper addresses the potential hazards associated with waste cheesecloth that has been exposed to nitric acid solutions. This issue was highlighted by the cleanup of a 100 ml leak of aqueous nitric acid solution containing Heat Source (HS) plutonium on 21 June 2016. Nitration of cellulosic material is a well-understood process due to industrial/military applications of the resulting material. Within the Department of Energy complex, nitric acids have been used extensively, as have cellulosic wipes. If cellulosic materials are nitrated, the cellulosic material can become ignitable and in extreme cases, reactive. We have chemistry knowledge and operating experience to support the conclusion that all current wastes are safe and compliant. There are technical questions worthy of further experimental evaluation. An extent of condition evaluation has been conducted back to 2004. During this time period there have been interruptions in the authorization to use cellulosic wipes in PF-4. Limited use has been authorized since 2007 (for purposes other than spill cleanup), so our extent of condition includes the entire current span of use. Our evaluation shows that there is no indication that process spills involving high molarity nitric acid were cleaned up with cheesecloth since 2007. The materials generated in the 21 June leak will be managed in a safe manner compliant with all applicable requirements.

  5. 76 FR 63878 - New Source Performance Standards Review for Nitric Acid Plants

    Science.gov (United States)

    2011-10-14

    ... improve compliance with various federal air emission regulations, we are proposing to require use of a... include reports of excess emissions and production rate. The frequency of reporting is semiannually as... ) emission limit, which applies to each nitric acid production unit commencing construction, modification,...

  6. Research on the Reaction Between Technetium and Hydrazine in Nitric Acid Medium

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The reaction between technetium and hydrazine in nitric acid medium was studied by the titration ofthe concentration of hydrazine and pursuing the concentration of heptavalent technetium along with time.It is approved that the reaction between technetium and hydrazine includes an inducing period, a fast

  7. Brightening of the global cloud field by nitric acid and the associated radiative forcing

    Directory of Open Access Journals (Sweden)

    R. Makkonen

    2012-08-01

    Full Text Available Clouds cool Earth's climate by reflecting 20% of the incoming solar energy, while also trapping part of the outgoing radiation. The effect of human activities on clouds is poorly understood, but the present-day anthropogenic cooling via changes of cloud albedo and lifetime could be of the same order as warming from anthropogenic addition in CO2. Soluble trace gases can increase water condensation to particles, possibly leading to activation of smaller aerosols and more numerous cloud droplets. We have studied the effect of nitric acid on the aerosol indirect effect with the global aerosol-climate model ECHAM5.5-HAM2. Including the nitric acid effect in the model increases cloud droplet number concentrations globally by 7%. The nitric acid contribution to the present-day cloud albedo effect was found to be −0.32 W m−2 and to the total indirect effect −0.46 W m−2. The contribution to the cloud albedo effect is shown to increase to −0.37 W m−2 by the year 2100, if considering only the reductions in available cloud condensation nuclei. Overall, the effect of nitric acid can play a large part in aerosol cooling during the following decades with decreasing SO2 emissions and increasing NOx and greenhouse gases.

  8. Photosynthetic and growth responses of Schima superba seedlings to sulfuric and nitric acid depositions.

    Science.gov (United States)

    Yao, Fang-Fang; Ding, Hui-Ming; Feng, Li-Li; Chen, Jing-Jing; Yang, Song-Yu; Wang, Xi-Hua

    2016-05-01

    A continuing rise in acid deposition can cause forest degradation. In China, acid deposition has converted gradually from sulfuric acid deposition (SAD) to nitric acid deposition (NAD). However, the differing responses of photosynthesis and growth to depositions of sulfuric vs. nitric acid have not been well studied. In this study, 1-year-old seedlings of Schima superba, a dominant species in subtropical forests, were treated with two types of acid deposition SO4 (2-)/NO3 (-) ratios (8:1 and 0.7:1) with two applications (foliar spraying and soil drenching) at two pH levels (pH 3.5 and pH 2.5) over a period of 18 months. The results showed that the intensity, acid deposition type, and spraying method had significant effects on the physiological characteristics and growth performance of seedlings. Acid deposition at pH 2.5 via foliar application reduced photosynthesis and growth of S. superba, especially in the first year. Unlike SAD, NAD with high acidity potentially alleviated the negative effects of acidity on physiological properties and growth, probably due to a fertilization effect that improved foliar nitrogen and chlorophyll contents. Our results suggest that trees were damaged mainly by direct acid stress in the short term, whereas in the long term, soil acidification was also likely to be a major risk to forest ecosystems. Our data suggest that the shift in acid deposition type may complicate the ongoing challenge of anthropogenic acid deposition to ecosystem stability.

  9. The Consistency of Isotopologues of Ambient Atmospheric Nitric Acid in Passively Collected Samples

    Science.gov (United States)

    Bell, M. D.; Sickman, J. O.; Bytnerowicz, A.; Padgett, P.; Allen, E. B.

    2012-12-01

    Anthropogenic sources of nitrogen oxides have previously been shown to have distinctive isotopic signatures of oxygen and nitrogen. Nylon filters are currently used in passive sampling arrays to measure ambient atmospheric nitric acid concentrations and estimate deposition rates. This experiment measured the ability of nylon filters to consistently collect isotopologues of atmospheric nitric acid in the same ratios as they are present in the atmosphere. Samplers were deployed in continuous stirred tank reactors (CSTR) and at field sites across a nitrogen deposition gradient in Southern California. Filters were exposed over a four week period with individual filters being subjected to 1-4 week exposure times. Extracted nitric acid were measured for δ18O and δ15N ratios and compared for consistency based on length of exposure and amount of HNO3 collected. Filters within the CSTRs collected HNO3 at a consistent rate in both high and low concentration chambers. After two weeks of exposure, the mean δ18O values were within 0.5‰ of the δ18O of the source HNO3 solution. The mean of all weekly exposures were within 0.5‰ of the δ15N of the source solution, but after three weeks, the mean δ15N of adsorbed HNO3 was within 0.2‰. As the length of the exposure increased, the variability of measured delta values decreased for both elements. The field samplers collected HNO3 consistent with previously measured values along a deposition gradient. The mean δ18O at high deposition sites was 52.2‰ compared to 35.7‰ at the low deposition sites. Mean δ15N values were similar at all sites across the deposition gradient. Due to precipitation events occurring during the exposure period, the δ15N and δ18O of nitric acid were highly variable at all field sites. At single sites, changes in δ15N and δ18O were negatively correlated, consistent with two-sourcing mixing dynamics, but the slope of the regressions differed between high and low deposition sites. Anthropogenic

  10. Nitric acid treated multi-walled carbon nanotubes optimized by Taguchi method

    Science.gov (United States)

    Shamsuddin, Shahidah Arina; Derman, Mohd Nazree; Hashim, Uda; Kashif, Muhammad; Adam, Tijjani; Halim, Nur Hamidah Abdul; Tahir, Muhammad Faheem Mohd

    2016-07-01

    Electron transfer rate (ETR) of CNTs can be enhanced by increasing the amounts of COOH groups to their wall and opened tips. With the aim to achieve the highest production amount of COOH, Taguchi robust design has been used for the first time to optimize the surface modification of MWCNTs by nitric acid oxidation. Three main oxidation parameters which are concentration of acid, treatment temperature and treatment time have been selected as the control factors that will be optimized. The amounts of COOH produced are measured by using FTIR spectroscopy through the absorbance intensity. From the analysis, we found that acid concentration and treatment time had the most important influence on the production of COOH. Meanwhile, the treatment temperature will only give intermediate effect. The optimum amount of COOH can be achieved with the treatment by 8.0 M concentration of nitric acid at 120 °C for 2 hour.

  11. Influence of Nitric Acid Concentration on Characteristics of Olive Stone Based Activated Carbon

    Institute of Scientific and Technical Information of China (English)

    Nouha Soudani; Souad Souissi-najar; Abdelmottaleb Ouederni

    2013-01-01

    In this work we investigated the effect of nitric acid concentration on the pore structure, surface chemis-try and liquid phase adsorption of olive stone based activated carbon prepared by mixing process using phosphoric acid and steam as activating agents. Chemicals and textural characterization show that the increase of HNO3 con-centration increases considerably the total acidic groups but decreases specific surface area and pore volume. The study of adsorption in aqueous solutions of two organics, phenol and methylene blue, on raw and oxidized activated carbon indicates that the treatment of mixed activated carbon with different concentrations of nitric acid improves the adsorbent capacity for methylene blue at HNO3 concentrations less or equal to 2 mol·L-1, while it has a negative effect on phenol adsorption.

  12. Nitric Acid Revamp and Upgrading of the Alarm & Protection Safety System at Petrokemija, Croatia

    Directory of Open Access Journals (Sweden)

    Hoško, I.

    2012-04-01

    Full Text Available Every industrial production, particularly chemical processing, demands special attention in conducting the technological process with regard to the security requirements. For this reason, production processes should be continuously monitored by means of control and alarm safety instrumented systems. In the production of nitric acid at Petrokemija d. d., the original alarm safety system was designed as a combination of an electrical relay safety system and transistorized alarm module system. In order to increase safety requirements and modernize the technological process of nitric acid production, revamping and upgrading of the existing alarm safety system was initiated with a new microprocessor system. The newly derived alarm safety system, Simatic PCS 7, links the function of "classically" distributed control (DCS and logical systems in a common hardware and software platform with integrated engineering tools and operator interface to meet the minimum safety standards with safety integrity level 2 (SIL2 up to level 3 (SIL3, according to IEC 61508 and IEC 61511. This professional paper demonstrates the methodology of upgrading the logic of the alarm safety system in the production of nitric acid in the form of a logical diagram, which was the basis for a further step in its design and construction. Based on the mentioned logical diagram and defined security requirements, the project was implemented in three phases: analysis and testing, installation of the safety equipment and system, and commissioning. Developed also was a verification system of all safety conditions, which could be applied to other facilities for production of nitric acid. With the revamped and upgraded interlock alarm safety system, a new and improved safety boundary in the production of nitric acid was set, which created the foundation for further improvement of the production process in terms of improved analysis.

  13. KINETIC STUDIES ON THE POLYMERIZATION OF ACRYLONITRILE INITIATED BY METALLIC MAGNESIUM-NITRIC ACID SYSTEM

    Institute of Scientific and Technical Information of China (English)

    WU Chinyung

    1983-01-01

    This article reports the polymerization kinetics of acrylonitrile initiated by metallic magnesiumnitric acid system. The rate of polymerization is independent of the amount of magnesium used; when the concentration of nitric acid is higher than acrylonitrile, the equation of polymerization kinetics may be expressed as Rp=1.91 × 105e-15000/RT[Mg]0 [AN]2·2 [HNO3]0·46 The result of copolymerization of acyrlonitrile and methyl acrylate supports a free-radical mechanism.

  14. Integrating nitric oxide into salicylic acid and jasmonic acid/ ethylene plant defense pathways.

    Science.gov (United States)

    Mur, Luis A J; Prats, Elena; Pierre, Sandra; Hall, Michael A; Hebelstrup, Kim H

    2013-01-01

    Plant defense against pests and pathogens is known to be conferred by either salicylic acid (SA) or jasmonic acid (JA)/ethylene (ET) pathways, depending on infection or herbivore-grazing strategy. It is well attested that SA and JA/ET pathways are mutually antagonistic allowing defense responses to be tailored to particular biotic stresses. Nitric oxide (NO) has emerged as a major signal influencing resistance mediated by both signaling pathways but no attempt has been made to integrate NO into established SA/JA/ET interactions. NO has been shown to act as an inducer or suppressor of signaling along each pathway. NO will initiate SA biosynthesis and nitrosylate key cysteines on TGA-class transcription factors to aid in the initiation of SA-dependent gene expression. Against this, S-nitrosylation of NONEXPRESSOR OF PATHOGENESIS-RELATED PROTEINS1 (NPR1) will promote the NPR1 oligomerization within the cytoplasm to reduce TGA activation. In JA biosynthesis, NO will initiate the expression of JA biosynthetic enzymes, presumably to over-come any antagonistic effects of SA on JA-mediated transcription. NO will also initiate the expression of ET biosynthetic genes but a suppressive role is also observed in the S-nitrosylation and inhibition of S-adenosylmethionine transferases which provides methyl groups for ET production. Based on these data a model for NO action is proposed but we have also highlighted the need to understand when and how inductive and suppressive steps are used.

  15. Integrating nitric oxide into salicylic acid and jasmonic acid/ ethylene plant defence pathways.

    Directory of Open Access Journals (Sweden)

    Luis A.J. Mur

    2013-06-01

    Full Text Available Plant defence against pests and pathogens is known to be conferred by either salicylic acid (SA or jasmonic acid (JA/ethylene (ET pathways, depending on infection or herbivore-grazing strategy. It is well attested that SA and JA/ET pathways are mutually antagonistic allowing defence responses to be tailored to particular biotic stresses. Nitric oxide (NO has emerged as a major signal influencing resistance mediated by both signalling pathways but no attempt has been made to integrate NO into established SA/JA/ET interactions. NO has been shown to act as an inducer or suppressor of signalling along each pathway. NO will initiate SA biosynthesis and nitrosylate key cysteines on TGA-class transcription factors to aid in the initiation of SA—dependent gene expression. Against this, S-nitrosylation of NONEXPRESSOR OF PATHOGENESIS-RELATED PROTEINS1 (NPR1 will promote the NPR1 oligomerisation within the cytoplasm to reduce TGA activation. In JA biosynthesis, NO will initiate the expression of JA biosynthetic enzymes, presumably to over-come any antagonistic effects of SA on JA-mediated transcription. NO will also initiate the expression of ET biosynthetic genes but a suppressive role is also observed in the S –nitrosylation and inhibition of s-adenosylmethionine transferases which provides methyl groups for ethylene production. Based on these data a model for NO action is proposed but we have also highlighted the need to understand when and how inductive and suppressive steps are used.

  16. Improvement in electrochemical capacitance of activated carbon from scrap tires by nitric acid treatment

    Science.gov (United States)

    Han, Yan; Zhao, Ping-Ping; Dong, Xiao-Ting; Zhang, Cui; Liu, Shuang-Xi

    2014-12-01

    Activated carbon (AC) obtained from the industrial pyrolytic tire char is treated by concentrated nitric acid (AC-HNO3) and then used as the electrode material for supercapacitors. Surface properties and electrochemical capacitances of AC and ACHNO3 are studied. It is found that the morphology and the porous texture for AC and AC-HNO3 have little difference, while the oxygen content increases and functional groups change after the acid treatment. Electrochemical results demonstrate that the AC-HNO3 electrode displays higher specific capacitance, better stability and cycling performance, and lower equivalent series resistance, indicating that AC obtained from the industrial pyrolytic tire char treated by concentrated nitric acid is applicable for supercapacitors.

  17. Extractive distillation of nitric acid using the two-pot concept

    Energy Technology Data Exchange (ETDEWEB)

    Counce, R.M.; Groenier, W.S.; Holland, W.D.; Jubin, R.T.; North, E.D.; Thompson, L.E. Jr.; Hebble, T.L.

    1982-12-01

    Experiments have confirmed the validity of a novel design for a nitric acid concentration system for use in shielded nuclear fuel reprocessing plants. Current plans for producing the scrub solution for the IODOX process require the concentration and recycle of low strength (< 68.5 wt %) nitric acid sources. The described system utilizes extractive distillation with Mg(NO/sub 3/)/sub 2/ as the solvent and features two pots: an extractive distillation pot in which a concentrated acid product is obtained by contacting the acid feed with the solvent and a solvent recovery pot in which the solvent is dehydrated and recovered for recycle. In these experiments, a concentrated product of 89 wt % nitric acid was produced from azeotropic feed. The available vapor-liquid equilibria data for the Mg(NO/sub 3/)/sub 2/-HNO/sub 3/-H/sub 2/O system has been empirically correlated, and a design methodology has been developed for the two-pot extractive distillation process.

  18. Nitric Acid-Treated Carbon Fibers with Enhanced Hydrophilicity for Candida tropicalis Immobilization in Xylitol Fermentation

    Directory of Open Access Journals (Sweden)

    Le Wang

    2016-03-01

    Full Text Available Nitric acid (HNO3-treated carbon fiber (CF rich in hydrophilic groups was applied as a cell-immobilized carrier for xylitol fermentation. Using scanning electron microscopy, we characterized the morphology of the HNO3-treated CF. Additionally, we evaluated the immobilized efficiency (IE of Candida tropicalis and xylitol fermentation yield by investigating the surface properties of nitric acid treated CF, specifically, the acidic group content, zero charge point, degree of moisture and contact angle. We found that adhesion is the major mechanism for cell immobilization and that it is greatly affected by the hydrophilic–hydrophilic surface properties. In our experiments, we found 3 hto be the optimal time for treating CF with nitric acid, resulting in an improved IE of Candida tropicalis of 0.98 g∙g−1 and the highest xylitol yield and volumetric productivity (70.13% and 1.22 g∙L−1∙h−1, respectively. The HNO3-treated CF represents a promising method for preparing biocompatible biocarriers for multi-batch fermentation.

  19. Oleic acid-dependent modulation of Nitric oxide associated 1 protein levels regulates nitric oxide-mediated defense signaling in Arabidopsis

    Science.gov (United States)

    The conserved cellular metabolites nitric oxide (NO) and oleic acid (18:1) are well-known regulators of disease physiologies in diverse organism. We show that NO production in plants is regulated via 18:1. Reduction in 18:1 levels, via a genetic mutation in the 18:1-synthesizing gene SUPPRESSOR OF S...

  20. Effect of Different Electrode Materials on the Electropolymerization Process of Aniline in Nitric Acid Media

    Science.gov (United States)

    Li, Yaozong; Yi, Yun; Yang, Weifang; Liu, Xiaoqing; Li, Yuanyuan; Wang, Wei

    2017-02-01

    The electropolymerization process of aniline on different electrode surfaces such as Pt, Au, RuTi and polyaniline film in nitric acid solution containing 1 M aniline was investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Proposed electrical equivalent circuits were used to give a further analysis. Results show that the electrode materials accelerate the aniline electropolymerization remarkably as a catalyst, especially the electrochemical oxidation process of monomer aniline to its cation radical, which is the key step to incur the electropolymerization reaction of aniline on the electrode surface. The polymerization of aniline on RuTi electrode has the lowest reaction resistance for its adsorption sites, and the catalytic effects of these different electrodes decrease in the order: RuTi > polyaniline film > Pt > Au. The results also show that several states of polyaniline films are formed during the potential linear scan process in nitric acid solution and the corresponding oxidation and reduction reaction are reversible.

  1. Evaluation of the Magnesium Hydroxide Treatment Process for Stabilizing PFP Plutonium/Nitric Acid Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Gerber, Mark A.; Schmidt, Andrew J.; Delegard, Calvin H.; Silvers, Kurt L.; Baker, Aaron B.; Gano, Susan R.; Thornton, Brenda M.

    2000-09-28

    This document summarizes an evaluation of the magnesium hydroxide [Mg(OH)2] process to be used at the Hanford Plutonium Finishing Plant (PFP) for stabilizing plutonium/nitric acid solutions to meet the goal of stabilizing the plutonium in an oxide form suitable for storage under DOE-STD-3013-99. During the treatment process, nitric acid solutions bearing plutonium nitrate are neutralized with Mg(OH)2 in an air sparge reactor. The resulting slurry, containing plutonium hydroxide, is filtered and calcined. The process evaluation included a literature review and extensive laboratory- and bench-scale testing. The testing was conducted using cerium as a surrogate for plutonium to identify and quantify the effects of key processing variables on processing time (primarily neutralization and filtration time) and calcined product properties.

  2. Effect of Different Electrode Materials on the Electropolymerization Process of Aniline in Nitric Acid Media

    Science.gov (United States)

    Li, Yaozong; Yi, Yun; Yang, Weifang; Liu, Xiaoqing; Li, Yuanyuan; Wang, Wei

    2016-11-01

    The electropolymerization process of aniline on different electrode surfaces such as Pt, Au, RuTi and polyaniline film in nitric acid solution containing 1 M aniline was investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Proposed electrical equivalent circuits were used to give a further analysis. Results show that the electrode materials accelerate the aniline electropolymerization remarkably as a catalyst, especially the electrochemical oxidation process of monomer aniline to its cation radical, which is the key step to incur the electropolymerization reaction of aniline on the electrode surface. The polymerization of aniline on RuTi electrode has the lowest reaction resistance for its adsorption sites, and the catalytic effects of these different electrodes decrease in the order: RuTi > polyaniline film > Pt > Au. The results also show that several states of polyaniline films are formed during the potential linear scan process in nitric acid solution and the corresponding oxidation and reduction reaction are reversible.

  3. Passive Sampler for Measurements of Atmospheric Nitric Acid Vapor (HNO3 Concentrations

    Directory of Open Access Journals (Sweden)

    Andrzej Bytnerowicz

    2001-01-01

    Full Text Available Nitric acid (HNO3 vapor is an important nitrogenous air pollutant responsible for increasing saturation of forests with nitrogen and direct injury to plants. The USDA Forest Service and University of California researchers have developed a simple and inexpensive passive sampler for monitoring air concentrations of HNO3. Nitric acid is selectively absorbed on 47-mm Nylasorb nylon filters with no interference from particulate NO3-. Concentrations determined with the passive samplers closely corresponded with those measured with the co-located honeycomb annular denuder systems. The PVC protective caps of standardized dimensions protect nylon filters from rain and wind and allow for reliable measurements of ambient HNO3 concentrations. The described samplers have been successfully used in Sequoia National Park, the San Bernardino Mountains, and on Mammoth Mountain in California.

  4. Study on the Reaction Between Methyl Hydrazine and Formaldehyde in Nitric Acid Medium

    Institute of Scientific and Technical Information of China (English)

    LI; Chuan-bo; CAO; Zhi; BIAN; Xiao-yan; XIAN; Liang; YAN; Tai-hong; ZHENG; Wei-fang

    2012-01-01

    <正>To make sure whether the reaction between formaldehyde and methyl hydrazine (MMH) could happen in dilute nitric acid solution, the condensation reaction between the two ones was investigated at 16 ℃. The reaction was slow and it took over 5 hours to reach the balance and the solution turned yellow at last. The maximum absorption peaks of the product existed at 340 nm and 400-450 nm, respectively.

  5. Procedure of Destructive Chemical Recovery of Precious Metals in Nitric Acid Production

    OpenAIRE

    Ljubičić, M.; Zečević, N.

    2012-01-01

    The heart of the nitric acid production process is the chemical reactor containing a platinum-based catalyst pack and an associated catchment system, which allows the ammonia oxidation reaction to take place efficiently. Under the severe operating conditions imposed by the high-pressure ammonia oxidation process, the catalyst gauzes experience progressive deterioration, as shown by the restricted surface of the catalyst wires, the loss of catalytic activity and the loss of catalytic materials...

  6. Extraction behaviour of Am(III) and Eu(III) from nitric acid medium in CMPO-HDEHP impregnated resins

    Energy Technology Data Exchange (ETDEWEB)

    Saipriya, K.; Kumar, T. [Bhabha Atomic Research Centre Facilities (India). Kalpakkam Reproscessing Plants; Kumaresan, R.; Nayak, P.K.; Venkatesan, K.A.; Antony, M.P. [Indira Gandhi Center for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

    2016-05-01

    Chromatographic resin containing extractants such as octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) or bis-(2-ethylhexyl)phosphoric acid (HDEHP) or mixture of extractants (CMPO + HDEHP) in an acrylic polymer matrix was prepared and studied for the extraction of Am(III) and Eu(III) over a range of nitric acid concentration. The effect of various parameters such as concentration of nitric acid in aqueous phase and the concentration of CMPO and HDEHP in the resin phase was studied. The distribution coefficient of Am(III) and Eu(III) in the impregnated resin increased with increased in the concentration of nitric acid for CMPO-impregnated resin, whereas a reverse trend was observed in HDEHP impregnated resin. In case of resin containing both the extractants, synergism was observed at low nitric acid concentration and antagonism at high nitric acid concentration. The mechanism of extraction was probed by slope analysis method at 0.01 and 2 M nitric acid concentrations. Citrate-buffered DTPA was used for the selective separation of Am(III), and a separation factor of 3-4 was obtained at pH 3.

  7. Kinetics of Reaction Between Tc(Ⅶ) and Monomethylhydrazine or Dimethylhydroxylamine in Nitric Acid Medium Containing Plutonium

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>The chemical reaction kinetics research of Tc(Ⅶ) with monomethylhydrazine or dimethylhydroxy-lamine in nitric acid medium demonstrated that Tc(Ⅶ) hardly reacts with the salt-free reagents during the

  8. Quantitative analysis of mixed hydrofluoric and nitric acids using Raman spectroscopy with partial least squares regression.

    Science.gov (United States)

    Kang, Gumin; Lee, Kwangchil; Park, Haesung; Lee, Jinho; Jung, Youngjean; Kim, Kyoungsik; Son, Boongho; Park, Hyoungkuk

    2010-06-15

    Mixed hydrofluoric and nitric acids are widely used as a good etchant for the pickling process of stainless steels. The cost reduction and the procedure optimization in the manufacturing process can be facilitated by optically detecting the concentration of the mixed acids. In this work, we developed a novel method which allows us to obtain the concentrations of hydrofluoric acid (HF) and nitric acid (HNO(3)) mixture samples with high accuracy. The experiments were carried out for the mixed acids which consist of the HF (0.5-3wt%) and the HNO(3) (2-12wt%) at room temperature. Fourier Transform Raman spectroscopy has been utilized to measure the concentration of the mixed acids HF and HNO(3), because the mixture sample has several strong Raman bands caused by the vibrational mode of each acid in this spectrum. The calibration of spectral data has been performed using the partial least squares regression method which is ideal for local range data treatment. Several figures of merit (FOM) were calculated using the concept of net analyte signal (NAS) to evaluate performance of our methodology.

  9. Thermal decomposition of organic solvent with nitric acid in nuclear fuel reprocessing plants

    Energy Technology Data Exchange (ETDEWEB)

    Koike, Tadao; Nishio, Gunji; Takada, Junichi; Tukamoto, Michio; Watanabe, Kouji [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Miyata, Sadaichirou

    1995-02-01

    Since a thermal decomposition of organic solvent containing TBP (tributyl phosphate) with nitric acid and heavy metal nitrates is an exothermic reaction, it is possible to cause an explosive decomposition of TBP-complex materials formed by a nitration between the solvent and nitric acid, if the solvent involving TBP-complex is heated upto a thermal limit in an evaporator to concentrate a fuel liquid solution from the extraction process in the reprocessing plant. In JAERI, the demonstration test for explosive decomposition of TBP-complex by the nitration was performed to elucidate the safety margin of the evaporator in the event of hypothetical explosion under auspices of the Science and Technology Agency. The demonstration test was carried out by heating TBP/n-dodecane solvent mixed with nitric acid and uranium nitrate. In the test, the thermal decomposition behavior of the solvent was examined, and also a kinematic reaction constant and a heat formation of the TBP-complex decomposition were measured by the test. In the paper, a safety analysis of a model evaporator was conducted during accidental conditions under the explosive decomposition of the solvent. (author).

  10. Supercritical fluid extraction of uranium and thorium from nitric acid medium using organophosphorous compounds

    Energy Technology Data Exchange (ETDEWEB)

    Pitchaiah, K.C.; Sujatha, K.; Rao, C.V.S. Brahmmananda; Subramaniam, S.; Sivaraman, N.; Rao, P.R. Vasudeva [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Chemistry Group

    2015-06-01

    In recent years, Supercritical Fluid Extraction (SFE) technique has been widely used for the extraction of metal ions. In the present study, extraction of uranium from nitric acid medium was investigated using supercritical carbon dioxide (Sc-CO{sub 2}) containing various organophosphorous compounds such as trialkyl phosphates e.g. tri-iso-amyl phosphate (TiAP), tri-sec-butyl phosphate (TsBP) and tri-n-butyl phosphate (TBP), dialkylalkyl phosphonates, e.g. diamylamyl phosphonate (DAAP) and dibutyl butyl phosphonate (DBBP), dialkyl hydrogen phosphonates, e.g. dioctyl hydrogen phosphonate (DOHP), dioctylphosphineoxide (DOPO), trioctyl phosphine oxide (TOPO), n-octylphenyl N,N-diisobutyl carbamoylmethylphosphine oxide (CMPO) and di-2-ethyl-hexyl phosphoric acid (HDEHP). Some of these ligands have been investigated for the first time in the supercritical phase for the extraction of uranium. The extraction efficiency of uranium was studied with TiAP, DAAP and DBBP as a function of nitric acid concentration; the kinetics of the equilibration period (static extraction) and transportation of the metal complex (dynamic extraction) was investigated. The influence of pressure and temperature on the extraction behaviour of uranium with DAAP was studied from 4 N HNO{sub 3}. The extraction efficiency of uranium from 4 N nitric acid medium was found to increase in the order of phosphates < phosphonates < HDEHP < TOPO < CMPO. In the case of phosphates and phosphonates, the maximum extraction of uranium was found to be from 4 N HNO{sub 3} medium. The acidic extractants, HDEHP and DOHP showed relatively higher extraction at lower acidities. The relative extraction of uranium and thorium from their mixture was also examined using Sc-CO{sub 2} containing phosphates, phosphonates and TOPO. The ligand, TsBP provided better fractionation between uranium and thorium compared to trialkyl phosphates, dialkyl alkyl phosphonates and TOPO.

  11. Macronutrient and fatty acid profiles of meagre (Argyrosomus regius fillets as influenced by harvesting time and boiling

    Directory of Open Access Journals (Sweden)

    Roberta Martelli

    2013-12-01

    Full Text Available The effect of harvesting time and cooking on water, protein, lipid, ash and fatty acid content of farmed meagre was assessed. Significant differences in nutrient content of raw fillets were detected in relation to harvesting time. Cooking by boiling induced loss of some macronutrients, mainly lipids and some fatty acids. Retention of total lipids, C18:2n-6 and C18:3n-3 decreased significantly with harvesting time, while C20:5n-3 (EPA and C22:6n-3 (DHA were retained in the same quantity. DHA retention was higher than that of the other FAs considered, at all harvesting times. The changes detected did not diminish the nutritional value of the fish. Despite losses induced by cooking and the low fat content, typical of this species, 100 g of fillet ensured an intake of EPA plus DHA more than double the recommended daily intake (250 mg day–1, at all harvesting times. The ability to preserve nutrients is an essential requirement for quality maintenance and suggests the possibility of heat-processing fillets. 

  12. Oscillate Boiling

    CERN Document Server

    Li, Fenfang; Nguyen, Dang Minh; Ohl, Claus-Dieter

    2016-01-01

    We report about an intriguing boiling regime occurring for small heaters embedded on the boundary in subcooled water. The microheater is realized by focusing a continuous wave laser beam to about $10\\,\\mu$m in diameter onto a 165\\,nm-thick layer of gold, which is submerged in water. After an initial vaporous explosion a single bubble oscillates continuously and repeatably at several $100\\,$kHz. The microbubble's oscillations are accompanied with bubble pinch-off leading to a stream of gaseous bubbles into the subcooled water. The self-driven bubble oscillation is explained with a thermally kicked oscillator caused by the non-spherical collapses and by surface pinning. Additionally, Marangoni stresses induce a recirculating streaming flow which transports cold liquid towards the microheater reducing diffusion of heat along the substrate and therefore stabilizing the phenomenon to many million cycles. We speculate that this oscillate boiling regime may allow to overcome the heat transfer thresholds observed dur...

  13. Coordination leaching of tungsten from scheelite concentrate with phosphorus in nitric acid

    Institute of Scientific and Technical Information of China (English)

    张文娟; 杨金洪; 赵中伟; 王文强; 李江涛

    2016-01-01

    A hydrometallurgical process for tungsten extraction and recovery from scheelite is reported. The technology includes leaching scheelite using phosphoric acid as chelating agent in nitric acid solutions, extracting tungsten by solvent extraction and reusing leaching agent. In the leaching process, affecting factors, such as temperature, leaching time, nitric acid and dosage of phosphoric acid, were examined on recovery of tungsten. Results show that more than 97% of tungsten could be extracted under conditions of leaching temperature of 80−90 °C, HNO3 concentration of 3.0−4.0 mol/L, liquild-to-soild ratio of 10:1, H3PO4 dosage of 3 stoichiometric ratio and leaching time of 3 h. Solvent extraction was then employed for the W recovery from the leachate with a organic system of 40%(v/v) N235, 30%(v/v) TBP, and 30%sulfonated kerosene. Approximately 99.93%of W was extracted and ammonium tungstate solution containing 193 g/L W was obtained with a stripping rate of 98.10%under the optimized conditions.

  14. FY13 GLYCOLIC-NITRIC ACID FLOWSHEET DEMONSTRATIONS OF THE DWPF CHEMICAL PROCESS CELL WITH SIMULANTS

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, D.; Zamecnik, J.; Best, D.

    2014-03-13

    Savannah River Remediation is evaluating changes to its current Defense Waste Processing Facility flowsheet to replace formic acid with glycolic acid in order to improve processing cycle times and decrease by approximately 100x the production of hydrogen, a potentially flammable gas. Higher throughput is needed in the Chemical Processing Cell since the installation of the bubblers into the melter has increased melt rate. Due to the significant maintenance required for the safety significant gas chromatographs and the potential for production of flammable quantities of hydrogen, eliminating the use of formic acid is highly desirable. Previous testing at the Savannah River National Laboratory has shown that replacing formic acid with glycolic acid allows the reduction and removal of mercury without significant catalytic hydrogen generation. Five back-to-back Sludge Receipt and Adjustment Tank (SRAT) cycles and four back-to-back Slurry Mix Evaporator (SME) cycles were successful in demonstrating the viability of the nitric/glycolic acid flowsheet. The testing was completed in FY13 to determine the impact of process heels (approximately 25% of the material is left behind after transfers). In addition, back-to-back experiments might identify longer-term processing problems. The testing was designed to be prototypic by including sludge simulant, Actinide Removal Product simulant, nitric acid, glycolic acid, and Strip Effluent simulant containing Next Generation Solvent in the SRAT processing and SRAT product simulant, decontamination frit slurry, and process frit slurry in the SME processing. A heel was produced in the first cycle and each subsequent cycle utilized the remaining heel from the previous cycle. Lower SRAT purges were utilized due to the low hydrogen generation. Design basis addition rates and boilup rates were used so the processing time was shorter than current processing rates.

  15. Nitric Acid Dehydration Using Perfluoro Carboxylate and Mixed Sulfonate/Carboxylate Membranes

    Energy Technology Data Exchange (ETDEWEB)

    Ames, Richard L. [Colorado School of Mines, Golden, CO (United States)

    2004-09-01

    Perfluoro ionomer membranes are tetrafluoro ethylene-based materials with microheterogeneous structures consisting of a hydrophobic polymer backbone and a hydrophilic side-chain cluster region. Due to the ionomer cluster morphology, these films exhibit unique transport properties. Recent investigations with perfluoro sulfonate and perfluoro sulfonate/carboxylate composite polymers have demonstrated their value in the dehydration of nitric acid and they show potential as an alternative to conventional, energy intensive unit operations in the concentration of acid feeds. As a result, investigations were conducted to determine the feasibility of using pure perfluoro carboxylate and mixed perfluoro sulfonate/carboxylate films for the dehydration of nitric acid because of the speculation of improved water selectivity of the carboxylate pendant chain. During the first phase of these investigations the effort was focused on generating a thin, solution cast perfluoro carboxylate ionomer film, to evaluate the general, chemical and physical characteristics of the polymer, and to assess the material's aqueous transport performance (flux and nitrate separation efficiencies) in pervaporation and high-pressure environments. Results demonstrated that generating robust solution-cast films was difficult yet a number of membranes survived high trans-membrane pressures up to 700 psig. General characterization of the solution cast product showed reduced ion exchange capacities when compared with thicker, ''as received'' perfluoro carboxylate and similar sulfonate films. Small angle x-ray scattering analysis results suggested that the solution cast carboxylate films contained a small fraction of sulfonate terminated side-chains. Aqueous transport experimentation showed that permeate fluxes for both pure water and nitric acid were approximately two orders of magnitude smaller for the carboxylate solution cast membranes when compared to their sulfonate

  16. Hypergolic Burning of Formylidene and Furfurylidene amines with Red Fuming Nitric Acid as Oxidizer

    Directory of Open Access Journals (Sweden)

    S. P. Panda

    1977-04-01

    Full Text Available Six p-formylidene and six p-furfurylideneamines were synthesized and their ignition delay with red fuming nitric acid (RFNA were measured by cup test method using a high speed camera. Structure - hypergolicity correlation revealed that a p-methyl group inhibits hypergolicity whereas a p-methoxy group accelerates it. Similarly oxidizable non-conjugated benzene rings increase hypergolicity whereas conjugated benzene rings decrease it. On compacting, the p-formylidene anisidine was found to be hypergolic with an ignition delay less than 100 milliseconds.

  17. Formation of substrate-based gold nanocage chains through dealloying with nitric acid

    Directory of Open Access Journals (Sweden)

    Ziren Yan

    2015-06-01

    Full Text Available Metal nanocages have raised great interest because of their new properties and wide applications. Here, we report on the use of galvanic replacement reactions to synthesize substrate-supported Ag–Au nanocages from silver templates electrodeposited on transparent indium tin oxide (ITO film coated glass. The residual Ag in the composition was dealloyed with 10% nitric acid. It was found that chains of Au nanocages were formed on the substrate surface during dealloying. When the concentration of HNO3 increased to 20%, the structures of nanocages were damaged and formed crescent or semi-circular shapes. The transfer process on the substrate surface was discussed.

  18. Direct Synthesis of Phenol from Benzene on an Activated Carbon Catalyst Treated with Nitric Acid

    Institute of Scientific and Technical Information of China (English)

    Cui-hong Chen; Jia-quan Xu; Ming-ming Jin; Gui-ying Li; Chang-wei Hu

    2011-01-01

    Commercially available coal-based activated carbon was treated by nitric acid with different concentrations and the resultant samples were used as catalysts for the direct hydroxylation of benzene to phenol in acetonitrile. Boehm titration, X-ray photoelectron spectroscopy,scanning electron microscope coupled with an energy dispersive X-ray microanalyzer, and Brunauer-Emmett-Teller method were used to characterize toe samples. The number of carboxyl groups on the surface was found to be the main factor affecting the catalytic activity. An optimum catalytic performance with a yield of 15.7% and a selectivity of 87.2% to phenol was obtained.

  19. Vertical Distribution of Ozone and Nitric Acid Vapor on the Mammoth Mountain, Eastern Sierra Nevada, California

    OpenAIRE

    2002-01-01

    In August and September 1999 and 2000, concentrations of ozone (O3) and nitric acid vapor (HNO3) were monitored at an elevation gradient (2184–3325 m) on the Mammoth Mountain, eastern Sierra Nevada, California. Passive samplers were used for monitoring exposure to tropospheric O3 and HNO3 vapor. The 2-week average O3 concentrations ranged between 45 and 72 ppb, while HNO3 concentrations ranged between 0.06 and 0.52 μg/m3. Similar ranges of O3 and HNO3 were determined for 2 years of the study....

  20. Enhanced sidewall functionalization of single-wall carbon nanotubes using nitric acid.

    Science.gov (United States)

    Tobias, Gerard; Shao, Lidong; Ballesteros, Belin; Green, Malcolm L H

    2009-10-01

    When a sample of as-made single-walled carbon nanotubes (SWNTs) is treated with nitric acid, oxidation debris are formed due to the functionalization (mainly carboxylation) of the amorphous carbon present in the sample and a continuous coating along the carbon nanotube walls is created preventing the sidewall functionalization of the SWNTs. This oxidation debris can be easily removed by an aqueous base wash leaving behind a sample with a low degree of functionality. After removal of the amorphous carbon (by steam purification) from a sample of as-made SWNTs, the resulting purified SWNTs are readily carboxylated on the walls by nitric acid treatment. The use of steam for the purification of SWNTs samples allows the removal of the amorphous carbon and graphitic layers coating the metal particles present in the sample without altering the tubular structure of the SWNTs. The exposed metal particles can then be easily removed by an acid wash. Comparison between the steam treatment and molten sodium hydroxide treatment is made.

  1. A Durable Catalyst for Vapor Phase Nitration of Benzene with Nitric Acid

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Experimental results in this work demonstrate that PW12-H2SO4/SiO2 catalyst is a good and durable catalyst for vapor phase nitration of benzene to nitrobenzene (NB) using 65% nitric acid at normal pressure. It retains the advantages of using H2SO4 as catalyst and the addition of phosphotungstic acid holds back the effusion of sulfuric acid. This new catalyst keeps high activity (the conversion of HNO3 is more than 92%), high selectivity of NB (more than 97%) and high space time yield (STY 1.5 kg NB/kg cat.h) even after 150 h on stream, under condition of 423 K, SV=3200 ml/g h.

  2. Integrated Computational and Experimental Protocol for Understanding Rh(III) Speciation in Hydrochloric and Nitric Acid Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Samuels, Alex C.; Boele, Cherilynn A.; Bennett, Kevin T.; Clark, Sue B.; Wall, Nathalie; Clark, Aurora E.

    2014-12-01

    A combined experimental and theoretical approach has investigated the complex speciation of Rh(III) in hydrochloric and nitric acid media, as a function of acid concentration. This has relevance to the separation and isolation of Rh(III) from dissolved spent nuclear fuel, which is an emergent and attractive alternative source of platinum group metals, relative to traditional mining efforts.

  3. Procedure of Destructive Chemical Recovery of Precious Metals in Nitric Acid Production

    Directory of Open Access Journals (Sweden)

    Ljubičić, M.

    2012-07-01

    Full Text Available The heart of the nitric acid production process is the chemical reactor containing a platinum-based catalyst pack and an associated catchment system, which allows the ammonia oxidation reaction to take place efficiently. Under the severe operating conditions imposed by the high-pressure ammonia oxidation process, the catalyst gauzes experience progressive deterioration, as shown by the restricted surface of the catalyst wires, the loss of catalytic activity and the loss of catalytic materials. The higher the pressure of gaseous ammonia oxidation, the greater the loss of platinum group metals from the surface of the applied selective heterogeneous catalysts. Total losses for one batch over the whole period of using selective heterogeneous catalysts may account in the range from 20 to 40 % of the total installed quantity of precious metals. An important part of the platinum removed from the platinum-rhodium alloy wires can be recovered at the outlet of the reactor by means of palladium catchment gauzes. However, this catchment process, which is based on the great ability of palladium to alloy with platinum, is not 100 % effective and a fraction of the platinum and practically all of the rhodium lost by the catalyst wires, evades the catchment package and is then deposited in other parts of the plant, especially heat exchangers. From the above mentioned operating equipment, the retained mass of precious metals can be recovered by the technical procedure of non-destructive and destructive chemical solid-liquid extraction.Shown is the technical procedure of destructive chemical recovery of preheater and boiler for preheating and production of steam by applying sulfuric acid (w = 20 % and subsequent procedure of raffination of derived sludge, to the final recovery of precious metals. The technical procedure of destructive chemical recovery of precious metals from preheater and boiler for preheating and production of steam in nitric acid production is

  4. Temperature effects on the nitric acid oxidation of industrial grade multiwalled carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Nadia F., E-mail: nadia@fisica.ufc.br [Universidade Federal do Ceara, Departamento de Fisica (Brazil); Martinez, Diego Stefani T., E-mail: diegostefani.br@gmail.com; Paula, Amauri J., E-mail: amaurijp@gmail.com [Universidade Estadual de Campinas (UNICAMP), Laboratorio de Quimica do Estado Solido (LQES), Instituto de Quimica (Brazil); Silveira, Jose V. [Universidade Federal do Ceara, Departamento de Fisica (Brazil); Alves, Oswaldo L., E-mail: oalves@iqm.unicamp.br [Universidade Estadual de Campinas (UNICAMP), Laboratorio de Quimica do Estado Solido (LQES), Instituto de Quimica (Brazil); Souza Filho, Antonio G., E-mail: agsf@fisica.ufc.br [Universidade Federal do Ceara, Departamento de Fisica (Brazil)

    2013-07-15

    In this study, we report an oxidative treatment of multiwalled carbon nanotubes (MWCNTs) by using nitric acid at different temperatures (25-175 Degree-Sign C). The analyzed materials have diameters varying from 10 to 40 nm and majority lengths between 3 and 6 {mu}m. The characterization results obtained by different techniques (e.g., field emission scanning electron microscopy, thermogravimetric analysis, energy-filtered transmission electron microscopy, Braunauer, Emmet and Teller method, {zeta}-potential and confocal Raman spectroscopy) allowed us to access the effects of temperature treatment on the relevant physico-chemical properties of the MWCNTs samples studied in view of an integrated perspective to use these samples in a bio-toxicological context. Analytical microbalance measurements were used to access the purity of samples (metallic residue) after thermogravimetric analysis. Confocal Raman spectroscopy measurements were used to evaluate the density of structural defects created on the surface of the tubes due to the oxidation process by using 2D Raman image. Finally, we have demonstrated that temperature is an important parameter in the generation of oxidation debris (a byproduct which has not been properly taken into account in the literature) in the industrial grade MWCNTs studied after nitric acid purification and functionalization.

  5. Decontamination of uranium-contaminated waste oil using supercritical fluid and nitric acid.

    Science.gov (United States)

    Sung, Jinhyun; Kim, Jungsoo; Lee, Youngbae; Seol, Jeunggun; Ryu, Jaebong; Park, Kwangheon

    2011-07-01

    The waste oil used in nuclear fuel processing is contaminated with uranium because of its contact with materials or environments containing uranium. Under current law, waste oil that has been contaminated with uranium is very difficult to dispose of at a radioactive waste disposal site. To dispose of the uranium-contaminated waste oil, the uranium was separated from the contaminated waste oil. Supercritical R-22 is an excellent solvent for extracting clean oil from uranium-contaminated waste oil. The critical temperature of R-22 is 96.15 °C and the critical pressure is 49.9 bar. In this study, a process to remove uranium from the uranium-contaminated waste oil using supercritical R-22 was developed. The waste oil has a small amount of additives containing N, S or P, such as amines, dithiocarbamates and dialkyldithiophosphates. It seems that these organic additives form uranium-combined compounds. For this reason, dissolution of uranium from the uranium-combined compounds using nitric acid was needed. The efficiency of the removal of uranium from the uranium-contaminated waste oil using supercritical R-22 extraction and nitric acid treatment was determined.

  6. Homogeneous nucleation rates of nitric acid dihydrate (NAD at simulated stratospheric conditions – Part II: Modelling

    Directory of Open Access Journals (Sweden)

    O. Möhler

    2006-01-01

    Full Text Available Activation energies ΔGact for the nucleation of nitric acid dihydrate (NAD in supercooled binary HNO3/H2O solution droplets were calculated from volume-based nucleation rate measurements using the AIDA (Aerosol, Interactions, and Dynamics in the Atmosphere aerosol chamber of Forschungszentrum Karlsruhe. The experimental conditions covered temperatures T between 192 and 197 K, NAD saturation ratios SNAD between 7 and 10, and nitric acid molar fractions of the nucleating sub-micron sized droplets between 0.26 and 0.28. Based on classical nucleation theory, a new parameterisation for ΔGact=A×(T ln SNAD−2+B is fitted to the experimental data with A=2.5×106 kcal K2 mol−1 and B=11.2−0.1(T−192 kcal mol−1. A and B were chosen to also achieve good agreement with literature data of ΔGact. The parameter A implies, for the temperature and composition range of our analysis, a mean interface tension σsl=51 cal mol−1 cm−2 between the growing NAD germ and the supercooled solution. A slight temperature dependence of the diffusion activation energy is represented by the parameter B. Investigations with a detailed microphysical process model showed that literature formulations of volume-based (Salcedo et al., 2001 and surface-based (Tabazadeh et al., 2002 nucleation rates significantly overestimate NAD formation rates when applied to the conditions of our experiments.

  7. Single-cycle method for partitioning of trivalent actinides using completely incinerable reagents from nitric acid medium

    Energy Technology Data Exchange (ETDEWEB)

    Ravi, Jammu; Venkatesan, K.A.; Antony, M.P.; Srinivasan, T.G.; Rao, P.R. Vasudeva [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

    2014-10-01

    A new approach, namely 'Single-cycle method for partitioning of Minor Actinides using completely incinerable ReagenTs' (SMART), has been explored for the separation of Am(III) from Eu(III) present in nitric acid medium. The extraction behavior of Am(III) and Eu(III) in a solution of an unsymmetrical diglycolamide, N,N,-didodecyl-N',N'-dioctyl-3-oxapentane-1,5-diamide (D{sup 3}DODGA), and an acidic extractant, N,N-di-2-ethylhexyl diglycolamic acid (HDEHDGA), in n-dodecane was studied. The distribution ratio of both these metal ions in D{sup 3}DODGA-HDEHDGA/n-dodecane initially decreased with increase in the concentration of nitric acid reached a minimum at 0.1 M nitric acid followed by increase. Synergic extraction of Am(III) and Eu(III) was observed at nitric acid concentrations above 0.1 M and antagonism at lower acidities. Contrasting behavior observed at different acidities was probed by the slope analysis of the extraction data. The study revealed the involvement of both D{sup 3}DODGA and HDEHDGA during synergism and increased participation of HDEHDGA during antagonism. The stripping behavior of Am(III) and Eu(III) from the loaded organic phase was studied as a function of nitric acid, DTPA, and citric acid concentrations. The conditions needed for the mutual separation of Am(III) and Eu(III) from the loaded organic phase were optimized. Our studies revealed the possibility of separating trivalent actinides from HLLW using these completely incinerable reagents. (orig.)

  8. Electrochemical oxidation of 243Am(III) in nitric acid by a terpyridyl-derivatized electrode

    Energy Technology Data Exchange (ETDEWEB)

    Dares, C. J.; Lapides, A. M.; Mincher, B. J.; Meyer, T. J.

    2015-11-05

    A high surface area, tin-doped indium oxide electrode surface-derivatized with a terpyridine ligand has been applied to the oxidation of trivalent americium to Am(V) and Am(VI) in nitric acid. Potentials as low as 1.8 V vs. the saturated calomel electrode are used, 0.7 V lower than the 2.6 V potential for one-electron oxidation of Am(III) to Am(IV) in 1 M acid. This simple electrochemical procedure provides, for the first time, a method for accessing the higher oxidation states of Am in non-complexing media for developing the coordination chemistries of Am(V) and Am(VI) and, more importantly, for separation of americium from nuclear waste streams.

  9. Effects of boiling on chlorogenic acid and the liver protective effects of its main products against CCl₄-induced toxicity in vitro.

    Science.gov (United States)

    Kan, Shidong; Cheung, Matt Wan Man; Zhou, Yanling; Ho, Wing Shing

    2014-02-01

    Chlorogenic acid (3-O-caffeoylquinic acid, CA) is the active component in several botanical beverage, vegetables, fruits, and herbal drugs. The effect of water boiling on the bioactivity of CA was studied. CA could be isomerized to 4-O-caffeoylquinic acid (4-O-CA) and 5-O-caffeoylquinic acid (5-O-CA) in decoctive extraction, and each of the isomers occupied about one-third of the total caffeoylquinic acids. A novel method, using water elution of microsphere resin, was used to purify CA and its 2 isomers. The yield of CA, 4-O-CA, and 5-O-CA was 82%, 5.6%, and 50%, with the purity of 98%, 97%, and 99%, respectively. The DPPH radical scavenging assay showed that 4-O-CA, 5-O-CA, and CA exhibited similar activity. However, there was no significant difference between 4-O-CA and 5-O-CA when used against CCl₄-induced toxicity in hepG2 cells. Our studies show that isomerization is the main transformation of CA in boiling, and the decoction could not decrease the anti-oxidant activity of CA.

  10. Nitric oxide metabolism and indole acetic acid biosynthesis cross-talk in Azospirillum brasilense SM.

    Science.gov (United States)

    Koul, Vatsala; Tripathi, Chandrakant; Adholeya, Alok; Kochar, Mandira

    2015-04-01

    Production of nitric oxide (NO) and the presence of NO metabolism genes, nitrous oxide reductase (nosZ), nitrous oxide reductase regulator (nosR) and nitric oxide reductase (norB) were identified in the plant-associated bacterium (PAB) Azospirillum brasilense SM. NO presence was confirmed in all overexpressing strains, while improvement in the plant growth response of these strains was mediated by increased NO and indole-3-acetic acid (IAA) levels in the strains. Electron microscopy showed random distribution to biofilm, with surface colonization of pleiomorphic Azospirilla. Quantitative IAA estimation highlighted a crucial role of nosR and norBC in regulating IAA biosynthesis. The NO quencher and donor reduced/blocked IAA biosynthesis by all strains, indicating their common regulatory role in IAA biosynthesis. Tryptophan (Trp) and l-Arginine (Arg) showed higher expression of NO genes tested, while in the case of ipdC, only Trp and IAA increased expression, while Arg had no significant effect. The highest nosR expression in SMnosR in the presence of IAA and Trp, along with its 2-fold IAA level, confirmed the relationship of nosR overexpression with Trp in increasing IAA. These results indicate a strong correlation between IAA and NO in A. brasilense SM and suggest the existence of cross-talk or shared signaling mechanisms in these two growth regulators.

  11. Extraction of uranium (VI) from nitric acid solutions with N,N,-di-n-butyloctanamide

    Energy Technology Data Exchange (ETDEWEB)

    Dembinski, W.; Gasparini, G.M.

    1980-12-01

    N,N-dialkylamides show interesting properties as new extracting agents of actinides. This report presents the data concerning the N,N-di-n-butyloctanamide: CH/sub 3/-(CH/sub 2/)/sub 5/-CH/sub 2/-C(O)N (C/sub 4/H/sub 9/)/sub 2/. In particular the following have been studied: the formation of a third phase with n-dodecane and mesitylene as diluents; the influence of the concentration of the uranium of the nitric acid and of the extractant on the distribution coeffcient, of uranium(VI); the radiation stability of this amide and the influence of the absorbed dose on the distribution coefficient for U(VI). The general properties of the di-n-butyloctanamide as potential extractant of uranium are discussed.

  12. Studies of dissolution solutions of ruthenium metal, oxide and mixed compounds in nitric acid

    Energy Technology Data Exchange (ETDEWEB)

    Mousset, F.; Eysseric, C.; Bedioui, F

    2004-07-01

    Ruthenium is one of the fission products generated by irradiated nuclear fuel. It is present throughout all the steps of nuclear fuel reprocessing-particularly during extraction-and requires special attention due to its complex chemistry and high {beta}{gamma} activity. An innovative electro-volatilization process is now being developed to take advantage of the volatility of RuO{sub 4} in order to eliminate it at the head end of the Purex process and thus reduce the number of extraction cycles. Although the process operates successfully with synthetic nitrato-RuNO{sup 3+} solutions, difficulties have been encountered in extrapolating it to real-like dissolution solutions. In order to better approximate the chemical forms of ruthenium found in fuel dissolution solutions, kinetic and speciation studies on dissolved species were undertaken with RuO{sub 2},xH{sub 2}O and Ru{sup 0} in nitric acid media. (authors)

  13. Study on Purification Diatomite with nitric acid by Thermal Closed System

    Directory of Open Access Journals (Sweden)

    Kuang Meng

    2016-01-01

    Full Text Available In this research, a purification approach using nitric acid leaching at thermal closed system was developed to improve the porous structure of raw diatomite by removal of impurities from its surface and clogged pores. The feasibility and efficiency of this approach were determined by XRF for chemical constitution of diatomite, SEM for morphology and BET for specific surface area of purified diatomite. The investigations indicated that the content of SiO2 was in order of 85.14% for raw diatomite and 98% for purified diatomite, the content of Fe2O3 decreases after purified; the integrity of the porous structure was confirmed by SEM, and increase in specific surface area from 18m2·g-1 to 36m2·g-1.

  14. N,N,N‘,N’—tetrabutylmalonamide as a new extractant for extraction of nitric acid and uranium(VI)

    Institute of Scientific and Technical Information of China (English)

    WangYou-Shao; SunXiao-Yu; 等

    1997-01-01

    N,N,N',N'-tetrabutylmalonamide(TBMA) is synthesized and used for extraction of uranyl(Ⅱ) ion from nitric acid media in a diluent composed of 50% 1,2,4-trimethyl benzene (TMB) and 50% kerosene(OK),The effects of nitric acid concentration,extractant concentration,temperature,slating-out agent (LiNO3) and back extraction on distribution coefficients of uranyl(Ⅱ) ion have been studied.The extraction of nitric acid is also studied.The main adduct of TBMA and HNO3 is HNO3.TBMA,and there are more than two kinds of adducts in 3.0mol/L nitric acid solutions,such as HNO3.TBMA,(HNO3)2,TBMA and (NHO3)3.TBMA.The complex formation of uranyl(Ⅱ) ion,nitrate ion and TBMA(1:2:1) as extracted species is further confirmed by IR spectra of the saturated extraction of uranyl(Ⅱ) ion with TBMA,and the values of thermodynamic parameters have also been calculated.

  15. Nitric Acid Deposition following an Astrophysical Ionizing Radiation Event is below Critical Loads for Terrestrial and Freshwater Ecosystems

    CERN Document Server

    Melott, Ben Neuenswander Adrian

    2014-01-01

    Nitric acid rainout is one of the effects of an astrophysical ionizing radiation event. The predicted values of nitrate rainout from previous work for a typical gamma ray burst (GRB) within our galaxy serve as an extreme example and are shown to be below critical loads of eutrophication and acidification for ecoregions in Europe and the US.

  16. Investigation on surface structure of potassium permanganate/nitric acid treated poly(tetrafluoroethylene)

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Congli; Liu, Shuling; Gong, Tianlong; Gu, Aiqun; Yu, Zili, E-mail: ziliyu@scu.edu.cn

    2014-10-30

    Highlights: • A new transformation (conversion) mechanism of PTFE surface from a hydrophobicity to a hydrophilicity was proposed through the treatment of KMnO{sub 4}/HNO{sub 3}. • Chemical reactions or defluorination of PTFE described in the reported paper was testified to be a misconceived conclusion by the combination of several testing measurements (IR, XPS, XRD and so on) in our present work. • Deposition of manganese oxide and/or manganese hydroxide on PTFE surface contributed to the hydrophilic property of the modified PTFE with KMnO{sub 4}/HNO{sub 3} treated. • The deposition thickness on the modified PTFE surface was about 5 μm, which was significantly helpful in enhancing the adhesive strength of PTFE with other materials. - Abstract: In the previous articles concerning the treatment of poly(tetrafluoroethylene) (PTFE) with potassium permanganate/nitric acid mixture, the conversion of a hydrophobic to a hydrophilic surface was partially assigned to the defluorination of PTFE and then the introduction of carbonyl and hydroxyl groups into the defluorinated sites. In the present work, PTFE sheets were treated with potassium permanganate/nitric acid, and the surfaces before and after treatment were comparatively characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The surface sediments of the treated PTFE were also determined by atomic absorption spectroscopy (AAS). The results indicate that the conversion of the hydrophobicity to the hydrophilicity on the modified PTFE surface is mainly due to the deposition of hydrophilic manganese oxides which covered the fluorocarbon surface, and no detectable chemical reactions of PTFE occur in the treating process.

  17. Effect of humidity on nitric acid uptake to mineral dust aerosol particles

    Directory of Open Access Journals (Sweden)

    A. Vlasenko

    2006-01-01

    Full Text Available This study presents the first laboratory observation of HNO3 uptake by airborne mineral dust particles. The model aerosols were generated by dry dispersion of Arizona Test Dust (ATD, SiO2, and by nebulizing a saturated solution of calcium carbonate. The uptake of 13N-labeled gaseous nitric acid was observed in a flow reactor on the 0.2–2 s reaction time scale at room temperature and atmospheric pressure. The amount of nitric acid appearing in the aerosol phase at the end of the flow tube was found to be a linear function of the aerosol surface area. SiO2 particles did not show any significant uptake, while the CaCO3 aerosol was found to be more reactive than ATD. Due to the smaller uncertainty associated with the reactive surface area in the case of suspended particles as compared to bulk powder samples, we believe that we provide an improved estimate of the rate of uptake of HNO3 to mineral dust. The fact that the rate of uptake was smaller at a concentration of 1012 than at 1011 was indicative of a complex uptake mechanism. The uptake coefficient averaged over the first 2 s of reaction time at a concentration of 1012 molecules cm-3 was found to increase with increasing relative humidity, from 0.022±0.007 at 12% RH to 0.113±0.017 at 73% RH , which was attributed to an increasing degree of solvation of the more basic minerals. The extended processing of the dust by higher concentrations of HNO3 at 85% RH led to a water soluble coating on the particles and enhanced their hygroscopicity.

  18. Ammonium nitrate evaporation and nitric acid condensation in DMT CCN counters

    Science.gov (United States)

    Romakkaniemi, S.; Jaatinen, A.; Laaksonen, A.; Nenes, A.; Raatikainen, T.

    2014-05-01

    The effect of inorganic semivolatile aerosol compounds on the cloud condensation nucleus (CCN) activity of aerosol particles was studied by using a computational model for a DMT-CCN counter, a cloud parcel model for condensation kinetics and experiments to quantify the modelled results. Concentrations of water vapour and semivolatiles as well as aerosol trajectories in the CCN column were calculated by a computational fluid dynamics model. These trajectories and vapour concentrations were then used as an input for the cloud parcel model to simulate mass transfer kinetics of water and semivolatiles between aerosol particles and the gas phase. Two different questions were studied: (1) how big a fraction of semivolatiles is evaporated from particles after entering but before particle activation in the DMT-CCN counter? (2) How much can the CCN activity be increased due to condensation of semivolatiles prior to the maximum water supersaturation in the case of high semivolatile concentration in the gas phase? Both experimental and modelling results show that the evaporation of ammonia and nitric acid from ammonium nitrate particles causes a 10 to 15 nm decrease to the critical particle size in supersaturations between 0.1% and 0.7%. On the other hand, the modelling results also show that condensation of nitric acid or similar vapour can increase the CCN activity of nonvolatile aerosol particles, but a very high gas phase concentration (as compared to typical ambient conditions) would be needed. Overall, it is more likely that the CCN activity of semivolatile aerosol is underestimated than overestimated in the measurements conducted in ambient conditions.

  19. Optimization of the nitrous vapors experimental conditions production by nitric acid electrochemical reduction; Optimisation des conditions operatoires de production de vapeurs nitreuses par reduction electrochimique d`acide nitrique

    Energy Technology Data Exchange (ETDEWEB)

    Lemaire, M.

    1996-11-22

    Gaseous nitrogen oxides (NO and NO{sub 2}) involved as oxidizing agents in nuclear fuel reprocessing can be produced by electrochemical reduction of nitric acid. This is an interesting alternative to the existing process because no wastes are generated. voltammetric studies on a platinum electrode show that two reduction potential regions are observed in concentrated nitric acid solutions, between 0,05 V{sub SHE} and between 0,5 V{sub SHE} and 1 V{sub SHE}. The highest potential region reduction mechanism was studied by: classical micro-electrolysis methods, macro-electrolysis methods, infrared spectroscopy coupled to electrochemistry. It was determined that the origin of nitric acid reduction is the electrochemical reduction of nitrous acid in nitric oxide which chemically reduces nitric acid. This reaction produces nitrous acid back which indicate an auto-catalytic behaviour of nitric acid reduction mechanism. Nitrogen dioxide evolution during nitric reduction can also explained by an other chemical reaction. If the potential value of platinum electrode is above 0,8 V{sub SHE}, products of the indirect nitric acid reduction are nitrous acid, nitrogen oxide and nitrogen dioxide. Below this value nitric oxide can be reduced in nitrous oxide. Thus the potential value is the most important parameter for the nitrogen oxides production selectivity. However, owing to the auto-catalytic character of the reduction mechanism, potential value can be controlled during intentiostatic industrial electrolysis. (author). 91 refs.

  20. N,N-dialkyl-2-hydroxyacetamides for modifier-free separation of trivalent actinides from nitric acid medium

    Energy Technology Data Exchange (ETDEWEB)

    Prathibha, T.; Kumaresan, R.; Selvan, B. Robert; Venkatesan, K.A.; Antony, M.P.; Vasudeva Rao, P.R. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

    2016-07-01

    The alkyl derivatives of N,N,-dialkyl-2-hydroxyacetamide (DAHyA), namely, N,N,-dihexyl-2-hydroxyacetamide (DHHyA), N,N,-dioctyl-2-hydroxyacetamide (DOHyA), N,N,-didecyl-2-hydroxyacetamide (DDHyA), were synthesized and characterized by FT-IR, and NMR spectroscopy. The extraction behaviour of Am(III) in a solution of DAHyA in n-dodecane was studied as a function of various parameters to evaluate the feasibility of using DAHyA for partitioning of trivalent actinides from high-level liquid waste (HLLW). The distribution ratio of Am(III) (D{sub Am(III)}) in 0.1 M DAHyA/n-DD increased from 10{sup -4} to > 200 with increase in nitric acid concentration from 1 M to 6 M. A D{sub Am(III)} value 10-70 was obtained in a nitric acid concentration range from 3-4 M. The extraction of Am(III) in 0.1 M DAHyA/n-dodecane decreased in the order DHHyA > DOHyA > DDHyA. The third-phase formation behaviour of nitric acid and neodymium (III) in 0.2 M DAHyA/n-dodecane was studied. Near stoichiometric amount of neodymium (III) can be loaded in octyl and decyl derivatives without any third-phase formation from 3-4 M nitric acid medium. Unlike other extractants, the loaded trivalent metal ion in DAHyA can be recovered even with 1 M nitric acid. Therefore, the study revealed that N,N,-dialkyl-2-hydroxyacetamides are promising candidates for partitioning the trivalent actinides from HLLW.

  1. Study of Removal Nitrous Acid From Nitric Acid Solution Using Packed Column

    Institute of Scientific and Technical Information of China (English)

    LAN; Tian; CHANG; Shang-wen; LIU; Jin-ping; ZHOU; Xian-ming; LI; Gao-liang; TANG; Hong-bin; HE; Hui

    2013-01-01

    It is necessary that the adjustment of the Pu(Ⅲ)to Pu(Ⅳ)should be used excess nitride gases befor the cycle of Pu purification in Purex.The mass of nitrous acid were present in solution after adjustment.Ifthe solution contain the mass of nitrous acid arrived at the cycle of Pupurification,the nitrous could react with Pu reducing agent in the processof Pu back-extractionbecause nitrous acid could extracted to organic,

  2. Validation Testing of the Nitric Acid Dissolution Step Within the K Basin Sludge Pretreatment Process

    Energy Technology Data Exchange (ETDEWEB)

    AJ Schmidt; CH Delegard; KL Silvers; PR Bredt; CD Carlson; EW Hoppe; JC Hayes; DE Rinehart; SR Gano; BM Thornton

    1999-03-24

    The work described in this report involved comprehensive bench-scale testing of nitric acid (HNO{sub 3}) dissolution of actual sludge materials from the Hanford K East (KE) Basin to confirm the baseline chemical pretreatment process. In addition, process monitoring and material balance information was collected to support the development and refinement of process flow diagrams. The testing was performed by Pacific Northwest National Laboratory (PNNL)for the US Department of Energy's Office of Spent Fuel Stabilization (EM-67) and Numatec Hanford Corporation (NHC) to assist in the development of the K Basin Sludge Pretreatment Process. The baseline chemical pretreatment process for K Basin sludge is nitric acid dissolution of all particulate material passing a 1/4-in. screen. The acid-insoluble fraction (residual solids) will be stabilized (possibly by chemical leaching/rinsing and grouting), packaged, and transferred to the Hanford Environmental Restoration Disposal Facility (ERDF). The liquid fraction is to be diluted with depleted uranium for uranium criticality safety and iron nitrate for plutonium criticality safety, and neutralized with sodium hydroxide. The liquid fraction and associated precipitates are to be stored in the Hanford Tank Waste Remediation Systems (TWRS) pending vitrification. It is expected that most of the polychlorinated biphenyls (PCBs), associated with some K Basin sludges, will remain with the residual solids for ultimate disposal to ERDF. Filtration and precipitation during the neutralization step will further remove trace quantities of PCBs within the liquid fraction. The purpose of the work discussed in this report was to examine the dissolution behavior of actual KE Basin sludge materials at baseline flowsheet conditions and validate the.dissolution process step through bench-scale testing. The progress of the dissolution was evaluated by measuring the solution electrical conductivity and concentrations of key species in the

  3. Freezing of sulfuric and nitric acid solutions: Implications for polar stratospheric cloud formation

    Science.gov (United States)

    Salcedo Gonzalez, Dara

    2000-12-01

    Polar Stratospheric Clouds (PSCs) play an important role in ozone chemistry during the polar winter. The magnitude of their effect depends on their phase, composition and formation mechanism, which are not fully understood yet. In order to understand how liquid PSCs freeze, two apparatus were designed to study the freezing behavior of small drops using a Fourier transform infrared (FTIR) spectrometer and an optical microscope. Sulfuric acid aqueous drops with composition of 10 to 50 wt % were studied with the FTIR apparatus. The surface on which the drops stand caused heterogeneous nucleation of ice, but not of the sulfuric acid hydrates. The more concentrated solutions (>40 wt %) supercooled to 130 K without freezing. Below 150 K these solutions formed an amorphous solid, which liquefied upon warming. Drops with composition of 40 to 64 wt % HNO3 were prepared and their phase transitions were detected with the optical microscope apparatus. Freezing temperatures of the drops were determined and homogeneous nucleation rates of nitric acid dihydrate (JNAD) and nitric acid trihydrate (JNAT) between 170 and 190 K were calculated. JNAT and JNAD depend predominantly on the saturation of the solid in the liquid solution: higher saturation ratios correspond to higher nucleation rates. Classical nucleation theory was used to parameterize this relation. Since the saturation ratios of NAD and NAT vary with temperature and composition in different ways, NAT or NAD can form preferentially under different conditions. Evidence was found that NAD catalyzes the nucleation of NAT below ~183 K. Mullite, cristobalite and alumina were tested as possible heterogeneous nuclei of volcanic origin for PSCs. They catalyze freezing of NAD and NAT at temperatures below 179 K, which are too low to be stratospherically important. The results suggest that the largest drops in a PSC will freeze homogeneously if the stratospheric temperature remains below the NAT condensation temperature for more

  4. Determination of Nitric Acid in Aqueous Solution of Uranium and Plutonium Purification Cycle by Near Infrared Spectroscopy

    Institute of Scientific and Technical Information of China (English)

    LI; Ding-ming; WANG; Lin; ZHANG; Li-hua; GONG; Yan-ping; MU; Ling; WU; Ji-zong

    2012-01-01

    <正>The concentration of nitric acid interfered with the distribution of uranium and plutonium in nuclear fuel reprocessing process. So, in the reprocessing process control analysis, the determination of the free acid plays an important role. Traditional laboratory analytical method of free acid needs large size sample and is time-consuming. Hence, development of fast analytical method for free acid has important significance for the reprocessing process control analysis. Near-infrared spectroscopy (NIRS) has been proved to be a powerful analytical tool and used in various fields, it’s seldom, however, used in spent

  5. Water-soluble nitric-oxide-releasing acetylsalicylic acid (ASA) prodrugs.

    Science.gov (United States)

    Rolando, Barbara; Lazzarato, Loretta; Donnola, Monica; Marini, Elisabetta; Joseph, Sony; Morini, Giuseppina; Pozzoli, Cristina; Fruttero, Roberta; Gasco, Alberto

    2013-07-01

    A series of water-soluble (benzoyloxy)methyl esters of acetylsalicylic acid (ASA), commonly known as aspirin, are described. The new derivatives each have alkyl chains containing a nitric oxide (NO)-releasing nitrooxy group and a solubilizing moiety bonded to the benzoyl ring. The compounds were synthesized and evaluated as ASA prodrugs. After conversion to the appropriate salt, most of the derivatives are solid at room temperature and all possess good water solubility. They are quite stable in acid solution (pH 1) and less stable at physiological pH. In human serum, these compounds are immediately metabolized by esterases, producing a mixture of ASA, salicylic acid (SA), and of the related NO-donor benzoic acids, along with other minor products. Due to ASA release, the prodrugs are capable of inhibiting collagen-induced platelet aggregation of human platelet-rich plasma. Simple NO-donor benzoic acids 3-hydroxy-4-(3-nitrooxypropoxy)benzoic acid (28) and 3-(morpholin-4-ylmethyl)-4-[3-(nitrooxy)propoxy]benzoic acid (48) were also studied as representative models of the whole class of benzoic acids formed following metabolism of the prodrugs in serum. These simplified derivatives did not trigger antiaggregatory activity when tested at 300 μM. Only 28 displays quite potent NO-dependent vasodilatatory action. Further in vivo evaluation of two selected prodrugs, {[2-(acetyloxy)benzoyl]oxy}methyl-3-[(3-[aminopropanoyl)oxy]-4-[3-(nitrooxy)propoxy]benzoate⋅HCl (38) and {[2-(acetyloxy)benzoyl]oxy}methyl 3-(morpholin-4-ylmethyl)-4-[3-(nitrooxy)propoxy]benzoate oxalate (49), revealed that their anti-inflammatory activities are similar to that of ASA when tested in the carrageenan-induced paw edema assay in rats. The gastrotoxicity of the two prodrugs was also determined to be lower than that of ASA in a lesion model in rats. Taken together, these results indicated that these NO-donor ASA prodrugs warrant further investigation for clinical application.

  6. A safer and flexible method for the oxygen functionalization of carbon nanotubes by nitric acid vapors

    Energy Technology Data Exchange (ETDEWEB)

    Santangelo, Saveria, E-mail: saveria.santangelo@unirc.it [Dipartimento di Ingegneria Civile, dell’Energia, dell’Ambiente e dei Materiali (DICEAM), Università “Mediterranea”, 89122 Reggio Calabria (Italy); Piperopoulos, Elpida [Dipartimento di Ingegneria Eletronica, Chimica ed Ingegneria Industriale (DIECII), Università di Messina, 98166 Messina (Italy); Fazio, Enza [Dipartimento di Fisica e di Scienze della Terra (DFST), Università di Messina, 98166 Messina (Italy); Faggio, Giuliana [Dipartimento di Ingegneria dell’Informazione, delle Infrastrutture e dell’Energia Sostenibile (DIIES), Università “Mediterranea”, 89122 Reggio Calabria (Italy); Ansari, Shabana [Dipartimento di Ingegneria Eletronica, Chimica ed Ingegneria Industriale (DIECII), Università di Messina, 98166 Messina (Italy); Lanza, Maurizio [Istituto per i Processi Chimico Fisici (IPCF) del CNR, 98158 Messina (Italy); Neri, Fortunato [Dipartimento di Fisica e di Scienze della Terra (DFST), Università di Messina, 98166 Messina (Italy); Messina, Giacomo [Dipartimento di Ingegneria dell’Informazione, delle Infrastrutture e dell’Energia Sostenibile (DIIES), Università “Mediterranea”, 89122 Reggio Calabria (Italy); Milone, Candida [Dipartimento di Ingegneria Eletronica, Chimica ed Ingegneria Industriale (DIECII), Università di Messina, 98166 Messina (Italy)

    2014-06-01

    The functionalization by nitric acid vapors at azeotropic concentration has been recently proposed to eliminate drawbacks of the widely utilized liquid phase functionalization method. This work suggests to exploit the so-called “salt effect” to improve the vapor phase oxidation method in terms of safety and flexibility. Increasing the relative volatility of acid, the addition of Mg(NO{sub 3}){sub 2} salt to the HNO{sub 3} + H{sub 2}O solution allows (i) obtaining vapors with HNO{sub 3} at the azeotropic concentration from a more diluted liquid solution (i.e. operating under safer conditions), and (ii) varying the concentration of HNO{sub 3} in the vapor phase even above the azeotropic concentration limit (with improved process flexibility). High-resolution transmission electron microscopy, thermo-gravimetry, Raman spectroscopy and X-ray photoemission spectroscopy systematic analyses are carried out on pristine and oxidized nanotubes in order to assess their functionalization degree, surface chemistry and structural evolution. The most relevant finding of this preliminary study is that the nanotube functionalization extent increases linearly with the HNO{sub 3} vapor concentration.

  7. Foliar loading and metabolic assimilation of dry deposited nitric acid air pollutants by trees.

    Science.gov (United States)

    Padgett, Pamela E; Cook, Hillary; Bytnerowicz, Andrzej; Heath, Robert L

    2009-01-01

    Dry deposition of nitric acid vapor (HNO(3)) is a major contributor to eutrophication of natural ecosystems. Although soil fertilization by nitrogen deposition is considered to be the primary pathway for changes in plant nutrient status and shifts in ecological structure, the aerial portion of plants offer many times the surface area in which to collect atmospheric HNO(3). As much as 60% of deposited nitrogen may be retained in the canopy and not land on the soil surface below. Although uptake and assimilation appears to contribute to retention, only a small percentage of dry deposition is recovered in assimilated N pools. To test the importance of biological activity on the process and measurements of dry deposition, we used controlled environmental chambers to compare deposition to living and freeze-dried foliage of four tree species using (15)N-labeled HNO(3). In living trees, assimilation was determined by (15)N incorporation into free amino acids and proteins in leaves and roots. From 10% to 60% of the retained HNO(3) was incorporated into the biologically active nitrogen pool. The remainder was bound to foliar surfaces in an insoluble form in either living or freeze-dried foliage. The importance of the boundary layer conditions emerged as a primary factor controlling dry deposition characteristics and measurements.Trade names and commercial enterprises or products are mentioned solely for information. No endorsements by the U.S. Department of Agriculture are implied.

  8. Hyaluronic acid abrogates nitric oxide-dependent stimulation of collagen degradation in cultured human chondrocytes.

    Science.gov (United States)

    Surazynski, Arkadiusz; Miltyk, Wojciech; Czarnomysy, Robert; Grabowska, Joanna; Palka, Jerzy

    2009-07-01

    Experimental inflammation induced in cultured chondrocytes by inflammatory cytokine IL-1 beta stimulates collagen degradation by metalloproteinases. We propose that nitric oxide (NO) may represent down stream signaling molecule of IL-1-induced collagen degradation in chondrocytes. It was found that IL-1 beta induced the activity of MMP-2 and MMP-9 during the 48 h time course of the experiment, especially after 24h incubation, while DETA/NO, donor of NO, stimulated the process at 12h incubation. The mechanism of IL-1-dependent stimulation of NO production was found at the level of iNOS expression and activation of NF-kappaB. We found that hyaluronic acid (HA) counteracted IL-induced degradation of collagen in chondrocytes. Although, HA by itself had no effect on the metaloproteinases activity, when added to IL-1 beta or DETA/NO treated chondrocytes it contributed to the restoration of the MMPs activity to the control level. The mechanism of this phenomenon involves inhibition of NF-kappaB activation. The data suggest that NO may represent a target molecule for protective effect of hyaluronic acid on interleukin-1-induced stimulation of metaloproteinases activity in cultured human chondrocytes.

  9. A quantitative test of infrared optical constants for supercooled sulphuric and nitric acid droplet aerosols

    Directory of Open Access Journals (Sweden)

    R. Wagner

    2003-05-01

    Full Text Available In situ Fourier transform infrared (FTIR extinction spectra of supercooled H2SO4/H2O and HNO3/H2O solution droplets were recorded in the large coolable aerosol chamber AIDA (Aerosol Interactions and Dynamics in the Atmosphere of Forschungszentrum Karlsruhe for a range of aerosol compositions and at temperatures extending down to 192 K. The measured spectra were quantitatively analysed in terms of aerosol composition and mass concentration by using Mie theory in combination with published refractive index data as input parameters. Simultaneously, total sulphuric acid and nitric acid mass concentrations from filter analysis and total water concentrations measured with the Lyman-a hygrometer of Forschungszentrum Jülich were used to calculate the aerosol composition at thermodynamic equilibrium inside the aerosol chamber. By comparing these measured aerosol parameters with those retrieved from the analysis of the FTIR spectra, the accuracy of the literature data sets of refractive indices could be assessed. In summary, four data sets were tested in the H2SO4/H2O system as well as two data sets in the HNO3/H2O system, partly revealing significant discrepancies in the retrieved aerosol properties. Potential explanations for these differences are discussed in this paper.

  10. The effect of fatty acid surfactants on the uptake of nitric acid to deliquesced NaCl aerosol

    Directory of Open Access Journals (Sweden)

    M. Ammann

    2008-09-01

    Full Text Available Surface active organic compounds have been observed in marine boundary layer aerosol. Here, we investigate the effect such surfactants have on the uptake of nitric acid (HNO3, an important removal reaction of nitrogen oxides in the marine boundary layer. The uptake of gaseous HNO3 on deliquesced NaCl aerosol was measured in a flow reactor using HNO3 labelled with the short-lived radioactive isotope 13N. The uptake coefficient γ on pure deliquesced NaCl aerosol was γ=0.5±0.2 at 60% relative humidity and 30 ppb HNO3(g. The uptake coefficient was reduced by a factor of 5–50 when the aerosol was coated with saturated linear fatty acids with carbon chain lengths of 18 and 15 atoms in monolayer quantities. In contrast, neither shorter saturated linear fatty acids with 12 and 9 carbon atoms, nor coatings with the unsaturated oleic acid (C18, cis-double bond had a detectable effect on the rate of HNO3 uptake. It is concluded that it is the structure of the monolayers formed, which determines their resistance towards HNO3 uptake. Fatty acids (C18 and C15, which form a highly ordered film in the so-called liquid condensed state, represent a significant barrier towards HNO3 uptake, while monolayers of shorter-chain fatty acids (C9, C12 and of the unsaturated oleic acid form a less ordered film in the liquid expanded state and do not hinder the uptake. Similarly, high contents of humic acids in the aerosol, a structurally inhomogeneous, quite water soluble mixture of oxidised high molecular weight organic compounds did not affect HNO3 uptake. As surfactant films on naturally occurring aerosol are expected to be less structured due to their chemical inhomogeneity, it is likely that their inhibitory effect on HNO3 uptake is smaller than that observed here for the C15 and C18 fatty acid monolayers.

  11. Effect of ascorbic acid supplementation on nitric oxide metabolites and systolic blood pressure in rats exposed to lead

    Directory of Open Access Journals (Sweden)

    Mohammad Amani

    2010-01-01

    Full Text Available Background: Extended exposure to low levels of lead causes high blood pressure in human and laboratory animals. The mechanism is not completely recognized, but it is relatively implicated with generation of free radicals, oxidant agents such as ROS, and decrease of available nitric oxide (NO. In this study, we have demonstrated the effect of ascorbic acid as an antioxidant on nitric oxide metabolites and systolic blood pressure in rats exposed to low levels of lead. Materials and Methods: The adult male Wistar rats weighing 200-250 g were divided into four groups: control, lead acetate (receiving 100 ppm lead acetate in drinking water, lead acetate plus ascorbic acid (receiving 100 ppm lead acetate and 1 g/l ascorbic acid in drinking water, and ascorbic acid (receiving 1 g/l ascorbic acid in drinking water groups. The animals were anesthetized with ketamin/xylazine (50 and 7 mg/kg, respectively, ip and systolic blood pressure was then measured from the tail of the animals by a sphygmomanometer. Nitric oxide levels in serum were measured indirectly by evaluation of its stable metabolites (total nitrite and nitrate (NOc. Results: After 8 and 12 weeks, systolic blood pressure in the lead acetate group was significantly elevated compared to the control group. Ascorbic acid supplementation could prevent the systolic blood pressure rise in the lead acetate plus ascorbic acid group and there was no significant difference relative to the control group. The serum NOc levels in lead acetate group significantly decreased in relation to the control group, but this reduction was not significantly different between the lead acetate plus ascorbic acid group and the control group. Conclusion: Results of this study suggest that ascorbic acid as an antioxidant prevents the lead induced hypertension. This effect may be mediated by inhibition of NOc oxidation and thereby increasing availability of NO.

  12. Evaluation of nitric and acetic acid resistance of cement mortars containing high-volume black rice husk ash.

    Science.gov (United States)

    Chatveera, B; Lertwattanaruk, P

    2014-01-15

    This paper presents the performance of cement mortar containing black rice husk ash (BRHA) under nitric and acetic acid attacks. The BRHA, collected from an electrical generating power plant that uses rice husk as fuel, was ground using a grinding machine. The compressive strength loss, weight loss, and expansion of mortars under nitric and acetic acid attack were investigated. The test results of BRHA properties in accordance with the ASTM C 618 standard found that the optimal grinding time was 4 h as this achieved a Blaine fineness of 5370 cm(2)/g. For parametric study, BRHA were used as a Portland cement Type 1 replacement at the levels of 0%, 10%, 20%, 30%, 40%, and 50% by weight of binder. The water-to-binder ratios were 0.55, 0.60, and 0.65. From test results, when the percentage replacements of BRHA in cement increased, it was observed that the strength loss and weight loss of mortars containing BRHA under acetic acid attack were higher than those of the mortars against nitric acid attack. It was found that, of the various BHRA mortars, the strength loss and weight loss due to nitric and acetic acid attacks were the lowest in the mortar with 10% BRHA replacement. For 10%, 20% and 30% BRHA replacements, the rate of expansion of the BRHA mortar decreased when compared with the control mortar. For the mortars with other percentage replacements of BRHA, the rate of expansion increased. Furthermore, the effective water-to-binder ratios of control and BRHA mortars were the primary factor for determining the durability of mortar mixed with BRHA.

  13. RBS/EBS/PIXE measurement of single-walled carbon nanotube modification by nitric acid purification treatment

    Science.gov (United States)

    Jeynes, J. C. G.; Jeynes, C.; Kirkby, K. J.; Rümmeli, M.; Silva, S. R. P.

    2008-04-01

    Single-walled carbon nanotubes (SWCNTs) have many potential applications, including a number of promising biological applications. Nitric acid treatment solubilises CNTs by introducing functional groups, as well as removing amorphous carbon contaminants. Here, we report simultaneous RBS/EBS/PIXE measurements of nitric acid treated SWCNTs, focussing on the metal, nitrogen and oxygen content. We found that nitrogen remains constant in the samples despite washing and dialysis indicating it has either bound irreversibly via intercalation with the SWCNT and/or has been included in functional groups. We also found that the ratio between oxygen and platinum (catalyst) remains constant with treatment time (sampled at 2, 4, 6 h), indicating no more functional groups are made after 2 h exposure.

  14. Characteristic of wet method of phosphorus recovery from polish sewage sludge ash with nitric acid

    Directory of Open Access Journals (Sweden)

    Gorazda Katarzyna

    2016-01-01

    Full Text Available Sewage Sludge Ash (SSA is a concentrated source of phosphorus and can be successfully recycled via a number of different routes. This paper presents research results on phosphorus recovery from differently combusted sewage sludge with the use of nitric acid extraction. Different SSA forms from Polish thermal utilization stations were compared. It was revealed that sewage treatment technology as well as combustion technology influence many physical and chemical parameters of ashes that are crucial for further phosphorus recovery from such waste according to the proposed method. Presented research defines extraction efficiency, characterized extracts composition and verifies the possibility of using SSA as cheaper and alternative sources of phosphorus compounds. Gdynia, Kielce and Kraków SSA have the best properties for the proposed technology of phosphorus recovery with high extraction efficiency greater than 86%. Unsuitable results were obtained for Bydgoszcz, Szczecin Slag and Warszawa SSA. Extraction process for Łódź and Szczecin Dust SSA need to be improved for a higher phosphorus extraction efficiency greater than 80%.

  15. Ambient concentrations of atmospheric ammonia, nitrogen dioxide and nitric acid in an intensive agricultural region

    Science.gov (United States)

    Zbieranowski, Antoni L.; Aherne, Julian

    2013-05-01

    The spatial and temporal distribution of ambient atmospheric gaseous reactive nitrogen (Nr) species concentrations (ammonia [NH3], nitrogen dioxide [NO2] and nitric acid [HNO3]) were measured at the field scale in an intensive agricultural region in southern Ontario, Canada. Atmospheric concentrations were measured with the Willems badge diffusive passive sampler (18 sites for NH3, 9 sites for NO2 and HNO3) for one year (April 2010-March 2011; under a two week measurement frequency) within a 15 km × 15 km area. Dry deposition was calculated using the inferential method and estimated across the entire study area. The spatial distribution of emission sources associated with agricultural activity resulted in high spatial variability in annual average ambient NH3 concentrations (8 μg m-3 within a 2 km distance, coefficient of variation ˜50%) and estimated dry deposition (4-13 kg N ha-1 yr-1) between sample sites. In contrast, ambient concentrations and deposition of both NO2 (˜5.2->6.5 μg m-3; 1.0-1.5 kg N ha-1 yr-1) and HNO3 (0.6-0.7 μg m-3; 0.5-1 kg N ha-1 yr-1) had low variability (coefficient of variation mycorrhiza and ground vegetation within adjacent semi-natural ecosystems (estimated at ˜10% of the study area).

  16. Investigations of the inhibition of copper corrosion in nitric acid solutions by ketene dithioacetal derivatives

    Energy Technology Data Exchange (ETDEWEB)

    Fiala, A. [Laboratoire de chimie moleculaire du controle de l' environnement et des mesures physico-chimiques, faculte des sciences exactes, universite Mentouri-Constantine, route de Ain-El-Bey, Constantine (Algeria)], E-mail: abdelfiala@yahoo.fr; Chibani, A. [Laboratoire de chimie moleculaire du controle de l' environnement et des mesures physico-chimiques, faculte des sciences exactes, universite Mentouri-Constantine, route de Ain-El-Bey, Constantine (Algeria); Darchen, A. [Laboratoire d' electrochimie, ecole nationale superieure de chimie de Rennes, avenue du general-Leclerc, 35700 Rennes (France); Boulkamh, A.; Djebbar, K. [Laboratoire de chimie moleculaire du controle de l' environnement et des mesures physico-chimiques, faculte des sciences exactes, universite Mentouri-Constantine, route de Ain-El-Bey, Constantine (Algeria)

    2007-10-15

    Ketene dithioacetal derivatives, namely 3-[bis(methylthio)methylene] pentane-2,4-dione (1), 3-(1,3-dithian-2-ylidene) pentane-2,4-dione (2) and 3-(1,3-dithiolan-2-ylidene) pentane-2,4-dione (3) were synthesized and their respective capacity to inhibit copper corrosion in 3 M HNO{sub 3} was investigated by means of weight loss, potentiodynamic polarization, scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence (XRF). The obtained results indicate that the addition of these compounds significantly decreases the corrosion rate. Potentiodynamic polarization studies clearly showed that the inhibition efficiency increases with increasing concentration of the investigated compounds at a fixed temperature, but decreases with increasing temperature. These results on the whole showed that the studied substances are good cathodic inhibitors for copper corrosion in nitric acid medium. SEM and energy dispersive X-ray (EDAX) examination of the copper surface revealed that these compounds prevented copper from corrosion by adsorption on its surface to form a protective film, which acts as a barrier to aggressive agents. The presence of these organic compounds adsorbed on the electrode surface was confirmed by XRF investigations.

  17. Effects of composite restorations on nitric oxide and uric acid levels in saliva

    Directory of Open Access Journals (Sweden)

    Nilgun Akgul

    2015-01-01

    Full Text Available Background and Aims: Dental materials that are used in dentistry should be harmless to oral tissues, and should, therefore, not contain any leachable toxic and diffusible substances capable of causing side effects. This study was intended to investigate the effects on salivary nitric oxide (NO and uric acid (UA levels after application of dental composite filling materials to healthy volunteers. Materials and Methods: A total of 52 individuals (32 female and 20 male participated in the study. Filtek Z250 composite filling material (3M ESPE, St Paul, MN, USA was applied to healthy volunteers. Saliva samples were collected before restoration (baseline and 1 h, 1-day, 7 days, and 30 days after restoration. NO concentrations were measured using the Griess reaction method, and UA was measured using an enzymatic method. Data were analyzed using repeated measures ANOVA and the Bonferroni post-hoc test (α =5%. Results: NO values increased statistically significant after 7 days (P 0.05. There was no correlation between NO and UA levels in saliva (P > 0.05. Conclusion: Composite resins activated the antioxidant system in saliva. However, further studies are now needed to confirm our findings and to permit a definitive conclusion.

  18. A New Process Study on Comprehensive Utilization of NOx from Nitric Acid Plant

    Institute of Scientific and Technical Information of China (English)

    Zhou Hou-zhen; Liang Hua

    2003-01-01

    Based on studies of controlling NOx from nitric acid exhaust gas domestic and abroad, this paper has developed a new technique on removal of NOx and production of a by-product with high added value-- MnO2. Experiment shows, pyrolusite, whose valid composition is MnO2, of absorbing NOx has the following characteristics: quick, low cost, no secondary pollutant. Moreover, exhaust gas can attain the required standards. If the temperature of the pyrolusite serum is 30℃, pH=4, containing 90 g/L MnO2, the absorptivity for 3 000 mg/m3 NOx is 89.2%. Furthermore,few of the impurities in pyrolusite dissolve in the absorption mother solution. The purification cost of product is very low.The purity of end product MnO2 is more than 99. 995% after purifying. Therefore, it is workable for the new technique on economy and technology. There are also obvious environmental benefits and marked economic returns.

  19. A New Process Study on Comprehensive Utilization of NOx from Nitric Acid Plant

    Institute of Scientific and Technical Information of China (English)

    ZhouHou-zhen; LiangHua

    2003-01-01

    Based on studies of controlling NOx from nitric acid exhaust gas domestic and abroad, this paper has developed a new technique on removal of NOx and production of a by-product with high added value MnO2. Experiment shows, pyrolusite, whose valid composition is MnO2, of absorbing NOx has the following characteristics: quick, low cost, no secondary pollutant. Moreover, exhaust gas can attain the required standards. If the temperature of the pyrolusite serum is 30℃, pH=4, containing 90 g/L MnO2, the absorptivity for 3 000 mg/m3 NOx is 89.2%. Furthermore,few of the impurities in pyrolusite dissolve in the absorption mother solution. The purification cost of product is very low.The purity of end product MnO2 is more than 99. 995% after purifying. Therefore, it is workable for the new technique on economy and technology. There are also obvious environmental benefits and marked economic returns.

  20. Involvement of nitric oxide in the signal transduction of salicylic acid regulating stomatal movement

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The effects and the relationship between salicylic acid (SA) and nitric oxide (NO) on Vicia faba L. stomatal movement were studied. The results here showed that exogenous SA and NO induced stomatal closure, 100 μmol/L SA induced a rapid and striking NO increase in the cytosol of guard cells. This phenomenon was largely pre-vented by 200 μmol/L 2-phenyl-4,4,5,5-tetramethylimida-zoline-1-oxyl-3-oxide (PTIO), a specific NO scavenger, and 25 μmol/L NG-nitro-L-Arg-methyl eater (L-NAME), an in-hibitor of NO synthase (NOS) in mammalian cells that also inhibits plant NOS. In addition, SA-induced stomatal closure was largely prevented by PTIO and L-NAME. These results provide evidence that guard cells generate NO in response to SA via NOS-like activity, and that such NO production is required for full stomatal closure in response to SA. H-(1,2,4)-oxadiazole-[4,3-α]quinoxalin-1-one (ODQ), an inhibitor of guanylate cyclase, and nicotinamide, an antago-nist of cADPR production, inhibited the effects of SA- and NO-induced stomatal closure. It suggests that both cGMP and cADPR might mediate the signal transduction of SA and NO-induced stomatal closure.

  1. Folic acid supplementation improves microvascular function in older adults through nitric oxide-dependent mechanisms.

    Science.gov (United States)

    Stanhewicz, Anna E; Alexander, Lacy M; Kenney, W Larry

    2015-07-01

    Older adults have reduced vascular endothelial function, evidenced by attenuated nitric oxide (NO)-dependent cutaneous vasodilatation. Folic acid and its metabolite, 5-methyltetrahydrofolate (5-MTHF), are reported to improve vessel function. We hypothesized that (i) local 5-MTHF administration and (ii) chronic folic acid supplementation would improve cutaneous microvascular function in ageing through NO-dependent mechanisms. There were two separate studies in which there were 11 young (Y: 22 ± 1 years) and 11 older (O: 71 ± 3 years) participants. In both studies, two intradermal microdialysis fibres were placed in the forearm skin for local delivery of lactated Ringer's solution with or without 5 mM 5-MTHF. Red cell flux was measured by laser-Doppler flowmetry. Cutaneous vascular conductance [CVC=red cell flux/mean arterial pressure] was normalized as percentage maximum CVC (%CVCmax) (28 mM sodium nitroprusside, local temperature 43°C). In study 1 after CVC plateaued during local heating, 20 mM NG-nitro-L-arginine methyl ester (L-NAME) was perfused at each site to quantify NO-dependent vasodilatation. The local heating plateau (%CVCmax: O = 82 ± 3 vs Y = 96 ± 1, P = 0.002) and NO-dependent vasodilatation (%CVCmax: O = 26 ± 6% vs Y = 49 ± 5, P = 0.03) were attenuated in older participants. 5-MTHF augmented the overall (%CVCmax = 91 ± 2, P = 0.03) and NO-dependent (%CVCmax = 43 ± 9%, P = 0.04) vasodilatation in older but not young participants. In study 2 the participants ingested folic acid (5 mg/day) or placebo for 6 weeks in a randomized, double-blind, crossover design. A rise in oral temperature of 1°C was induced using a water-perfused suit, body temperature was held and 20 mM L-NAME was perfused at each site. Older participants had attenuated reflex (%CVCmax: O = 31 ± 8 vs Y = 44 ± 5, P = 0.001) and NO-dependent (%CVCmax: O = 9 ± 2 vs Y = 21 ± 2, P = 0.003) vasodilatation. Folic acid increased CVC (%CVCmax = 47 ± 5%, P = 0.001) and NO

  2. Accurate quantification and transformation of arsenic compounds during wet ashing with nitric acid and microwave assisted heating.

    Science.gov (United States)

    Goessler, W; Pavkov, M

    2003-06-01

    Arsenous acid, dimethylarsinic acid (DMA), methylarsonic acid (MA), arsenic acid, arsenobetaine bromide (AB), trimethylarsine oxide (TMAO), arsenocholine iodide (AC), and tetramethylarsonium iodide (TETRA) were heated in a microwave autoclave with nitric acid to 100-300 degrees C. The arsenic compounds in the digests were separated with anion- and cation-exchange chromatography and determined with an inductively coupled plasma mass spectrometer as arsenic-specific detector. Arsenous acid was completely oxidized to arsenic acid at 100 degrees C. For a complete oxidation of MA and DMA to arsenic acid temperatures > 220 degrees C and > 280 degrees C were necessary. AB decomposed to arsenic acid via TMAO. Complete conversion was only obtained after heating the sample for 90 min to 300 degrees C. For a complete conversion of TMAO similar harsh conditions were necessary. AC was already substantially degraded to TMAO, TETRA and two unknown compounds at 100 degrees C. The unknown arsenic compounds were found only in the digests up to 160 degrees C. Quantitative conversion of AC to arsenic acid went also via TMAO. At temperatures above 220 degrees C TETRA started to convert to TMAO, which then was further converted to arsenic acid. To investigate whether the results obtained for the arsenic standards are transferable to real samples, the certified reference material DORM-2 was also heated in nitric acid with variable digestion temperatures and times. For an almost complete conversion of the AB present in DORM-2 90 min at 300 degrees C were necessary. Total organic carbon (TOC) was less or = 260 degrees C for 60 min. UV photo-oxidation of DORM-2 was investigated as an alternative sample decomposition. Only 6% of AB was converted to arsenic acid when DORM-2 was irradiated for 2 h at 1000 W. In contrast to microwave heating substantial amounts of MA were observed as degradation product.

  3. Thermal And Spectroscopic Analyses Of Next Generation Caustic Side Solvent Extraction Solvent Contacted With 3, 8, And 16 Molar Nitric Acid

    Energy Technology Data Exchange (ETDEWEB)

    Fondeur, F. F.; Fink, S. D.

    2011-12-07

    A new solvent system referred to as Next Generation Solvent or NGS, has been developed at Oak Ridge National Laboratory for the removal of cesium from alkaline solutions in the Caustic Side Solvent Extraction process. The NGS is proposed for deployment at MCU{sup a} and at the Salt Waste Processing Facility. This work investigated the chemical compatibility between NGS and 16 M, 8 M, and 3 M nitric acid from contact that may occur in handling of analytical samples from MCU or, for 3 M acid, which may occur during contactor cleaning operations at MCU. This work shows that reactions occurred between NGS components and the high molarity nitric acid. Reaction rates are much faster in 8 M and 16 M nitric acid than in 3 M nitric acid. In the case of 16 M and 8 M nitric acid, the nitric acid reacts with the extractant to produce initially organo-nitrate species. The reaction also releases soluble fluorinated alcohols such as tetrafluoropropanol. With longer contact time, the modifier reacts to produce a tarry substance with evolved gases (NO{sub x} and possibly CO). Calorimetric analysis of the reaction product mixtures revealed that the organo-nitrates reaction products are not explosive and will not deflagrate.

  4. Study on reduction and back extraction of Pu(IV) by urea derivatives in nitric acid conditions

    Energy Technology Data Exchange (ETDEWEB)

    Ye, G.A.; Xiao, S.T.; Yan, T.H.; Lin, R.S.; Zhu, Z.W. [China Institute of Atomic Energy, P.O.Box 275(26), Beijing 102413 (China)

    2013-07-01

    The reduction kinetics of Pu(IV) by hydroxyl-semicarbazide (HSC), hydroxyurea (HU) and di-hydroxyurea (DHU) in nitric acid solutions were investigated separately with adequate kinetic equations. In addition, counter-current cascade experiments were conducted for Pu split from U in nitric acid media using three kinds of reductant, respectively. The results show that urea derivatives as a kind of novel salt-free reductant can reduce Pu(IV) to Pu(III) rapidly in the nitric acid solutions. The stripping experimental results showed that Pu(IV) in the organic phase can be stripped rapidly to the aqueous phase by the urea derivatives, and the separation factors of plutonium /uranium can reach more than 10{sup 4}. This indicates that urea derivatives is a kind of promising salt-free agent for uranium/plutonium separation. In addition, the complexing effect of HSC with Np(IV) was revealed, and Np(IV) can be back-extracted by HSC with a separation factor of about 20.

  5. Remedial investigation report on the abandoned nitric acid pipeline at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-01

    Upper East Fork Poplar Creek OU-2 consists of the Abandoned Nitric Acid Pipeline. This pipeline was installed in 1951 to transport liquid wastes {approximately} 4,800 ft from Buildings 9212, 9215, and 9206 to the S-3 Ponds. Materials known to have been discharged through the pipeline include nitric acid, depleted and enriched uranium, various metal nitrates, salts, and lead skimmings. A total of nineteen locations were chosen to be investigated along the pipeline for the first phase of this Remedial Investigation. Sampling consisted of drilling down to obtain a soil sample at a depth immediately below the pipeline. Additional samples were obtained deeper in the subsurface depending upon the depth of the pipeline, the depth of the water table, and the point of auger refusal. The nineteen samples collected below the pipeline were analyzed by the Y-12 Plant laboratory for metals, nitrate/nitrite, and isotopic uranium. Samples collected from three boreholes were also analyzed for volatile organic compounds because these samples produced a response with organic vapor monitoring equipment. The results of the baseline human health risk assessment for the Abandoned Nitric Acid Pipeline contaminants of potential concern show no unacceptable risks to human health via incidental ingestion of soil, inhalation of dust, dermal contact with the soil, or external exposure to radionuclides in the ANAP soils, under the construction worker and/or the residential land-use scenarios.

  6. Development of a Quantum Cascade Laser-Based Detector for Ammonia and Nitric Acid

    Energy Technology Data Exchange (ETDEWEB)

    Zahniser, Mark S.; Nelson, David D.; McManus, J. Barry; Shorter, Joanne H.; Herndon, Scott C.; Jimenez, Rodrigo

    2005-12-31

    We have developed a compact, robust, atmospheric trace gas detector based on mid-infrared absorption spectroscopy using pulsed quantum cascade (QC) lasers. The spectrometer is suitable for airborne measurements of ammonia, nitric acid, formaldehyde, formic acid, methane, nitrous oxide, carbon monoxide, nitrogen dioxide and other gases that have line-resolved absorption spectra in the mid-infrared spectral region. The QC laser light source operates near room temperature with thermal electric cooling instead of liquid nitrogen which has been previously required for semiconductor lasers in the mid-infrared spectral region. The QC lasers have sufficient output power so that thermal electric cooled detectors may be used in many applications with lower precision requirements. The instrument developed in this program has been used in several field campaigns from both the Aerodyne Mobile Laboratory and from the NOAA WP3 aircraft. The Phase II program has resulted in more than 10 archival publications describing the technology and its applications. Over 12 instruments based on this design have been sold to research groups in Europe and the United States making the program both a commercial as well as a technological success. Anticipated Benefits The development of a sensitive, cryogen-free, mid-infrared absorption method for atmospheric trace gas detection will have wide benefits for atmospheric and environmental research and broader potential commercial applications in areas such as medical diagnostic and industrial process monitoring of gaseous compounds. Examples include air pollution monitoring, breath analysis, combustion exhaust diagnostics, and plasma diagnostics for semi-conductor fabrication. The substitution of near-room temperature QC lasers for cryogenic lead salt TDLs and the resulting simplifications in instrument design and operation will greatly expand the range of applications.

  7. Fast and Simultaneous Determination of Pu(Ⅳ) and Nitric Acid in Spent Nuclear Fuel Reprocessing Sample by Near Infrared Spectroscopy

    Institute of Scientific and Technical Information of China (English)

    LI; Ding-ming; ZHANG; Li-hua; WANG; Ling; GONG; Yan-ping; FAN; De-jun; YI; Bao-shan; CHEN; Qiang; JI; Yong-chao; WU; Ji-zong

    2013-01-01

    Determination of Pu(Ⅳ)and nitric acid plays significant role in nuclear fuel reprocessing plant to control process accurately and timely.Coupling C-T fixed-type grating with InGaAs detector,a new novel analytical system for simultaneous measurement of nitric acid and Pu(Ⅳ)was developed by our working group.After obtaining near infrared absorptive spectra by the spectroscopic instrument,the spectra data

  8. Low Temperature Selective Catalytic Reduction of Nitrogen Oxides in Production of Nitric Acid by the Use of Liquid

    Directory of Open Access Journals (Sweden)

    Kabljanac, Ž.

    2011-11-01

    Full Text Available This paper presents the application of low-temperature selective catalytic reduction of nitrous oxides in the tail gas of the dual-pressure process of nitric acid production. The process of selective catalytic reduction is carried out using the TiO2/WO3 heterogeneous catalyst applied on a ceramic honeycomb structure with a high geometric surface area per volume. The process design parameters for nitric acid production by the dual-pressure procedure in a capacity range from 75 to 100 % in comparison with designed capacity for one production line is shown in the Table 1. Shown is the effectiveness of selective catalytic reduction in the temperature range of the tail gas from 180 to 230 °C with direct application of liquid ammonia, without prior evaporation to gaseous state. The results of inlet and outlet concentrations of nitrous oxides in the tail gas of the nitric acid production process are shown in Figures 1 and 2. Figure 3 shows the temperature dependence of the selective catalytic reduction of nitrous oxides expressed as NO2in the tail gas of nitric acid production with the application of a constant mass flow of liquid ammonia of 13,0 kg h-1 and average inlet mass concentration of the nitrous oxides expressed as NO2of 800,0 mgm-3 during 100 % production capacity. The specially designed liquid-ammonia direct-dosing system along with the effective homogenization of the tail gas resulted in emission levels of nitrous oxides expressed as NO2 in tail gas ranging from 100,0 to 185,0 mg m-3. The applied low-temperature selective catalytic reduction of the nitrous oxides in the tail gases by direct use of liquid ammonia is shown in Figure 4. It is shown that low-temperature selective catalytic reduction with direct application of liquid ammonia opens a new opportunity in the reduction of nitrous oxide emissions during nitric acid production without the risk of dangerous ammonium nitrate occurring in the process of subsequent energy utilization of

  9. A comparison of copper and acid site zeolites for the production of nitric oxide for biomedical applications.

    Science.gov (United States)

    Russell, Samantha E; González Carballo, Juan María; Orellana-Tavra, Claudia; Fairen-Jimenez, David; Morris, Russell E

    2017-03-21

    Copper-exchanged and acidic zeolites are shown to produce nitric oxide (NO) from a nitrite source in biologically active (nanomolar) concentrations. Four zeolites were studied; mordenite, ferrierite, ZSM-5 and SSZ-13, which had varying pore size, channel systems and Si/Al ratios. ZSM-5 and SSZ-13 produced the highest amounts of NO in both the copper and acid form. The high activity and regeneration of the copper active sites makes them good candidates for long-term NO production. Initial cytotoxicity tests have shown at least one of the copper zeolites (Cu-SSZ-13) to be biocompatible, highlighting the potential usage within biomedical applications.

  10. Nitric oxide-releasing poly(lactic-co-glycolic acid)-polyethylenimine nanoparticles for prolonged nitric oxide release, antibacterial efficacy, and in vivo wound healing activity.

    Science.gov (United States)

    Nurhasni, Hasan; Cao, Jiafu; Choi, Moonjeong; Kim, Il; Lee, Bok Luel; Jung, Yunjin; Yoo, Jin-Wook

    2015-01-01

    Nitric oxide (NO)-releasing nanoparticles (NPs) have emerged as a wound healing enhancer and a novel antibacterial agent that can circumvent antibiotic resistance. However, the NO release from NPs over extended periods of time is still inadequate for clinical application. In this study, we developed NO-releasing poly(lactic-co-glycolic acid)-polyethylenimine (PEI) NPs (NO/PPNPs) composed of poly(lactic-co-glycolic acid) and PEI/diazeniumdiolate (PEI/NONOate) for prolonged NO release, antibacterial efficacy, and wound healing activity. Successful preparation of PEI/NONOate was confirmed by proton nuclear magnetic resonance, Fourier transform infrared spectroscopy, and ultraviolet/visible spectrophotometry. NO/PPNPs were characterized by particle size, surface charge, and NO loading. The NO/PPNPs showed a prolonged NO release profile over 6 days without any burst release. The NO/PPNPs exhibited potent bactericidal efficacy against methicillin-resistant Staphylococcus aureus (MRSA) and Pseudomonas aeruginosa concentration-dependently and showed the ability to bind on the surface of the bacteria. We also found that the NO released from the NO/PPNPs mediates bactericidal efficacy and is not toxic to healthy fibroblast cells. Furthermore, NO/PPNPs accelerated wound healing and epithelialization in a mouse model of a MRSA-infected wound. Therefore, our results suggest that the NO/PPNPs presented in this study could be a suitable approach for treating wounds and various skin infections.

  11. Optimization of conditions to produce nitrous gases by electrochemical reduction of nitric acid; Optimisation des conditions operatoires de production de vapeurs nitreuses par reduction electrochimique d`acide nitrique

    Energy Technology Data Exchange (ETDEWEB)

    Lemaire, M. [CEA Centre d`Etudes Nucleaires de Saclay, 91 -Gif-sur-Yvette (France)]|[CEA Centre d`Etudes de la Vallee du Rhone, 30 -Marcoule (France). Direction du Cycle du Combustible

    1996-11-22

    Gaseous nitrogen oxides (NO and NO{sub 2}) involved as oxidizing agents in nuclear fuel reprocessing can be an produced by electrochemical reduction of nitric acid. This could be an interesting alternative to the usual process because no wastes are generated. Voltammetric studies on a platinum electrode show that two reduction potential regions are observed in concentrated nitric acid solutions, between 0.05 V{sub S}HE and 0.3 V{sub S}HE and O.5 V{sub S}HE and 1 V{sub S}HE. The highest potential region reduction mechanism was studies by: classical micro-electrolysis methods; macro-electrolysis methods; infra-red spectroscopy couplet to electrochemistry. It was determined that the origin of nitric acid reduction is the electrochemical reduction of nitrous acid in nitric oxide which chemically reduces nitric acid. This reaction produces nitrous acid back which indicate an auto-catalytic behaviour of nitric acid reduction mechanism. Nitrogen dioxide evolution during nitric acid reduction can also be explained by an other chemical reaction. In the potential value of platinum electrode is above 0.8 V{sub S}HE, products of the indirect nitric acid reduction are nitrous acid, nitrogen oxide and nitrogen dioxide. Below this value nitric oxide can be reduced in nitrous oxide. Thus the potential value is the most important parameter for the nitrogen oxides production selectivity. However, owing to the auto-catalytic character of the reduction mechanism, potential value can be controlled during intentiostatic industrial electrolysis. (author). 91 refs.

  12. Chronic exposure to ozone and nitric acid vapor results in increased levels of rat pulmonary putrescine

    Energy Technology Data Exchange (ETDEWEB)

    Sindhu, R.K.; Kikkawa, Yutaka [Department of Pathology, College of Medicine, University of California at Irvine, Irvine (United States); Mautz, W.J. [Department of Community and Environmental Medicine, University of California at Irvine, Irvine, CA (United States)

    1998-06-01

    In the past decade, there has been growing public concern for the human health effects of exposure to environmental pollutants. Ozone (O{sub 3}) is one of the most reactive components of photochemical air pollution. Despite extensive investigations by many laboratories on the functional, biochemical, and cellular effects of O{sub 3} exposure in humans, animals, and in vitro systems, questions remain concerning the potential adverse effects to human health represented by chronic near-ambient exposure to this environmental pollutant. In the present investigation, the influence of inhalation of O{sub 3} and nitric acid (HNO{sub 3}) vapor on polyamine levels was examined in rat lungs. Male F344/N rats were exposed nose-only to 0.15 ppm O{sub 3} and 50 {mu}g/m{sup 3} HNO{sub 3} vapor alone and in combination for 4 hours/day, 3 days/week for a total of 40 weeks. At this time the animals were sacrificed and their lungs were examined for polyamine contents. Exposure to O{sub 3} and O{sub 3} plus HNO{sub 3} vapor caused a significant increase in the putrescine content of the lung compared to the air-exposed controls (P < 0.05). The concentrations of pulmonary spermidine and spermine were not significantly increased by exposure to either O{sub 3} or HNO{sub 3} vapor alone or in combination compared to the air-exposed controls. The role of polyamines in repair and anti-inflammatory processes has been discussed. (orig.) (orig.) With 1 fig., 1 tab., 30 refs.

  13. Laboratory evaluation of the effect of nitric acid uptake on frost point hygrometer performance

    Directory of Open Access Journals (Sweden)

    T. Thornberry

    2010-08-01

    Full Text Available Chilled mirror hygrometers (CMH are widely used to measure water vapour in the troposphere and lower stratosphere from balloon-borne sondes. Systematic discrepancies among in situ water vapour instruments have been observed at low water vapour mixing ratios (<5 ppm in the upper troposphere and lower stratosphere (UT/LS. Understanding the source of the measurement discrepancies is important for a more accurate and reliable determination of water vapour abundance in this region. We have conducted a laboratory study to investigate the potential interference of gas-phase nitric acid (HNO3 with the measurement of frost point temperature, and consequently the water vapour mixing ratio, determined by CMH under conditions representative of operation in the UT/LS. No detectable interference in the measured frost point temperature was found for HNO3 mixing ratios of up to 4 ppb for exposure times up to 150 min. HNO3 was observed to co-condense on the mirror frost, with the adsorbed mass increasing linearly with time at constant exposure levels. Over the duration of a typical balloon sonde ascent (90–120 min, the maximum accumulated HNO3 amounts were comparable to monolayer coverage of the geometric mirror surface area, which corresponds to only a small fraction of the actual frost layer surface area. This small amount of co-condensed HNO3 is consistent with the observed lack of HNO3 interference in the frost point measurement because the CMH utilizes significant reductions (>10% in surface reflectivity by the condensate to determine H2O.

  14. Laboratory evaluation of the effect of nitric acid uptake on frost point hygrometer performance

    Directory of Open Access Journals (Sweden)

    T. Thornberry

    2011-02-01

    Full Text Available Chilled mirror hygrometers (CMH are widely used to measure water vapour in the troposphere and lower stratosphere from balloon-borne sondes. Systematic discrepancies among in situ water vapour instruments have been observed at low water vapour mixing ratios (<5 ppm in the upper troposphere and lower stratosphere (UT/LS. Understanding the source of the measurement discrepancies is important for a more accurate and reliable determination of water vapour abundance in this region. We have conducted a laboratory study to investigate the potential interference of gas-phase nitric acid (HNO3 with the measurement of frost point temperature, and consequently the water vapour mixing ratio, determined by CMH under conditions representative of operation in the UT/LS. No detectable interference in the measured frost point temperature was found for HNO3 mixing ratios of up to 4 ppb for exposure times up to 150 min. HNO3 was observed to co-condense on the mirror frost, with the adsorbed mass increasing linearly with time at constant exposure levels. Over the duration of a typical balloon sonde ascent (90–120 min, the maximum accumulated HNO3 amounts were comparable to monolayer coverage of the geometric mirror surface area, which corresponds to only a small fraction of the actual frost layer surface area. This small amount of co-condensed HNO3 is consistent with the observed lack of HNO3 interference in the frost point measurement because the CMH utilizes significant reductions (>10% in surface reflectivity by the condensate to determine H2O.

  15. Intergranular corrosion testing of austenitic stainless steels in nitric acid solutions

    Energy Technology Data Exchange (ETDEWEB)

    Whillock, G.O.H.; Dunnett, B. F. [British Nuclear Fuels plc, BNFL, B170, Sellafield, Seascale, Cumbria CA20 1PG (United Kingdom)

    2004-07-01

    In hot strong nitric acid solutions, stainless steels exhibit intergranular corrosion. Corrosion rates are often measured from immersion testing of specimens manufactured from the relevant material (e.g. plate or pipe). The corrosion rates, measured from weight loss, are found to increase with time prior to reaching steady state, which can take thousands of hours to achieve. The apparent increase in corrosion rate as a function of time was found to be an artefact due to the surface area of the specimen's being used in the corrosion rate calculations, rather than that of the true area undergoing active corrosion i.e. the grain boundaries. The steady state corrosion rate coincided with the onset of stable grain dropping, where the use of the surface area of the specimen to convert the weight loss measurements to corrosion rates was found to be appropriate. This was confirmed by sectioning of the specimens and measuring the penetration depths. The rate of penetration was found to be independent of time and no induction period was observed. A method was developed to shorten considerably the testing time to reach the steady state corrosion rate by use of a pre-treatment that induces grain dropping. The long-term corrosion rates from specimens which were pre-treated was similar to that achieved after prolonged testing of untreated (i.e. initially ground) specimens. The presence of cut surfaces is generally unavoidable in the simple immersion testing of specimens in test solutions. However, inaccuracy in the results may occur as the measured corrosion rate is often influenced by the orientation of the microstructure, the highest rates typically being observed on the cut surfaces. Two methods are presented which allow deconvolution of the corrosion rates from immersion testing of specimens containing cut surfaces, thus allowing reliable prediction of the long-term corrosion rate of plate surfaces. (authors)

  16. Influence of Fe loadings on desulfurization performance of activated carbon treated by nitric acid.

    Science.gov (United States)

    Guo, Jia-Xiu; Shu, Song; Liu, Xiao-Li; Wang, Xue-Jiao; Yin, Hua-Qiang; Chu, Ying-Hao

    2017-02-01

    A series of Fe supported on activated carbon treated by nitric acid are prepared by incipient wetness impregnation with ultrasonic assistance and characterized by N2 adsorption-desorption, X-ray diffraction, Fourier transform infrared spectrum and X-ray photoelectron spectroscopy. It has shown that Fe loadings significantly influence the desulfurization activity. Fe/NAC5 exhibits an excellent removal ability of SO2, corresponding to breakthrough sulfur capacity of 323 mg/g. With the increasing Fe loadings, the generated Fe3O4 and Fe2SiO4 increase, but Fe2(SO4)3 is observed after desulfurization. Fe/NAC1 has a Brunauer-Emmett-Teller (BET) surface area of 925 m(2)/g with micropore surface area of 843 m(2)/g and total pore volume of 0.562 cm(3)/g including a micropore volume of 0.300 cm(3)/g. With the increasing Fe loadings, BET surface area and micropore volume decrease, and those of Fe/NAC10 decrease to 706 m(2)/g and 0.249 cm(3)/g. The Fe loadings influence the pore-size distribution, and SO2 adsorption mainly reacts in micropores at about 0.70 nm. C=O and C-O are observed for all samples before SO2 removal. After desulfurization, the C-O stretching is still detected, but the C=O stretching vibration of carbonyl groups disappears. The stretching of S-O or S=O in sulfate is observed at 592 cm(-1) for the used sample, proving that the existence of [Formula: see text].

  17. Rocket Performance of Red Fuming Nitric Acid with Blends of Norbornadiene, Carene and Cardanol

    Directory of Open Access Journals (Sweden)

    R. Chhibber

    1992-07-01

    Full Text Available The fuel blends of nornornadiene and carene (50:50 by weight and norbornadiene, carene and cardanol (40:40:20 by weight exhibit synergistic hypergolic ignition with red fuming nitric acid (RFNA as oxidiser. These fuel blends have been evaluated by theoretical calculations of performance parameters and subsequently verified by static firing in a 10 kg/sub f/ thruster at a chamber pressure of around 20 atm, using RFNA (with 21 per cent N/sub 2/O/sub 4/ by weight as oxidiser. The theoretical calculations show maximum specific impulse and C*values at the O/F, 3 to be 227.8 s and 1598.7 m/s respectively for the norbornadiene-carene blend. The corresponding values for the norbornadiene, carene and cardanol blend were found to be 226.8 s and 1586.0 m/s respectively at the O/F, 4. For theoretical calculations, the chamber pressure (P/sub c and the exit pressure (P/sub e/0 were assumed to be 20 and 1 atm, respectively. The static firing of the propellants in a 10 kg thruster exhibited smooth pressure-time curves with the experimental C* values in close agreement with those calculated and the non-deposition of carbon in the nozzle. This indicated low combustion instability and high combustion efficiency under rocket conditions (> 0.9. The fuel blends with their low cost and toxicity and relatively high density can replace G-fuel used in several Indian missiles without impairing the performance.

  18. Ab initio aqueous thermochemistry: application to the oxidation of hydroxylamine in nitric acid solution.

    Science.gov (United States)

    Ashcraft, Robert W; Raman, Sumathy; Green, William H

    2007-10-18

    Ab initio molecular orbital calculations were performed and thermochemical parameters estimated for 46 species involved in the oxidation of hydroxylamine in aqueous nitric acid solution. Solution-phase properties were estimated using the several levels of theory in Gaussian03 and using COSMOtherm. The use of computational chemistry calculations for the estimation of physical properties and constants in solution is addressed. The connection between the pseudochemical potential of Ben-Naim and the traditional standard state-based thermochemistry is shown, and the connection of these ideas to computational chemistry results is established. This theoretical framework provides a basis for the practical use of the solution-phase computational chemistry estimates for real systems, without the implicit assumptions that often hide the nuances of solution-phase thermochemistry. The effect of nonidealities and a method to account for them is also discussed. A method is presented for estimating the solvation enthalpy and entropy for dilute aqueous solutions based on the solvation free energy from the ab initio calculations. The accuracy of the estimated thermochemical parameters was determined through comparison with (i) enthalpies of formation in the gas phase and in solution, (ii) Henry's law data for aqueous solutions, and (iii) various reaction equilibria in aqueous solution. Typical mean absolute deviations (MAD) for the solvation free energy in room-temperature water appear to be ~1.5 kcal/mol for most methods investigated. The MAD for computed enthalpies of formation in solution was 1.5-3 kcal/mol, depending on the methodology employed and the type of species (ion, radical, closed-shell) being computed. This work provides a relatively simple and unambiguous approach that can be used to estimate the thermochemical parameters needed to build detailed ab initio kinetic models of systems in aqueous solution. Technical challenges that limit the accuracy of the estimates are

  19. Modulation of Ionotropic Glutamate Receptors and Acid-Sensing Ion Channels by Nitric Oxide

    Directory of Open Access Journals (Sweden)

    John Q Wang

    2012-05-01

    Full Text Available Ionotropic glutamate receptors (iGluR are ligand-gated ion channels and are densely expressed in broad areas of mammalian brains. Like iGluRs, acid-sensing ion channels (ASIC are ligand (H+-gated channels and are enriched in brain cells and peripheral sensory neurons. Both ion channels are enriched at excitatory synaptic sites, functionally coupled to each other, and subject to the modulation by a variety of signaling molecules. Central among them is a gasotransmitter, nitric oxide (NO. Available data show that NO activity-dependently modulates iGluRs and ASICs via either a direct or an indirect pathway. The former involves a NO-based and cGMP-independent posttranslational modification (S-nitrosylation of extracellular cysteine residues in channel subunits or channel-interacting proteins. The latter is achieved by NO activation of soluble guanylyl cyclase, which in turn triggers an intracellular cGMP-sensitive cascade to indirectly modulate iGluRs and ASICs. The NO modification is usually dynamic and reversible. Modified channels undergo significant, interrelated changes in biochemistry and electrophysiology. Since NO synthesis is enhanced in various neurological disorders, the NO modulation of iGluRs and ASICs is believed to be directly linked to the pathogenesis of these disorders. This review summarizes the direct and indirect modifications of iGluRs and ASICs by NO and analyzes the role of the NO-iGluR and NO-ASIC coupling in cell signaling and in the pathogenesis of certain related neurological diseases.

  20. The Significance of Lewis Acid Sites for the Selective Catalytic Reduction of Nitric Oxide on Vanadium-Based Catalysts.

    Science.gov (United States)

    Marberger, Adrian; Ferri, Davide; Elsener, Martin; Kröcher, Oliver

    2016-09-19

    The long debated reaction mechanisms of the selective catalytic reduction (SCR) of nitric oxide with ammonia (NH3 ) on vanadium-based catalysts rely on the involvement of Brønsted or Lewis acid sites. This issue has been clearly elucidated using a combination of transient perturbations of the catalyst environment with operando time-resolved spectroscopy to obtain unique molecular level insights. Nitric oxide reacts predominantly with NH3 coordinated to Lewis sites on vanadia on tungsta-titania (V2 O5 -WO3 -TiO2 ), while Brønsted sites are not involved in the catalytic cycle. The Lewis site is a mono-oxo vanadyl group that reduces only in the presence of both nitric oxide and NH3 . We were also able to verify the formation of the nitrosamide (NH2 NO) intermediate, which forms in tandem with vanadium reduction, and thus the entire mechanism of SCR. Our experimental approach, demonstrated in the specific case of SCR, promises to progress the understanding of chemical reactions of technological relevance.

  1. A laboratory study of the heterogeneous reaction of nitric acid on calcium carbonate particles

    Science.gov (United States)

    Goodman, A. L.; Underwood, G. M.; Grassian, V. H.

    2000-12-01

    It has been postulated that the reaction of nitric acid with calcium carbonate, namely, CaCO3(s) + 2HNO3(g) → Ca(NO3)2(s) + CO2(g) + H2O(g), plays an important role in the atmosphere. In this study, transmission FTIR spectroscopy, diffuse reflectance UV-visible spectroscopy, transmission electron microscopy and a Knudsen cell reactor coupled to a quadrupole mass spectrometer have been used to investigate the heterogeneous reactivity of HNO3 on CaCO3 at 295 K as a function of relative humidity. Transmission FTIR spectroscopy was used to probe both gas-phase and adsorbed products and showed that the reaction of HNO3 and CaCO3 is limited to the surface of the CaCO3 particle in the absence of adsorbed water. However, in the presence of water vapor, the reaction is greatly enhanced and is not limited to the surface of the particle producing both solid calcium nitrate and gaseous carbon dioxide. The enhanced reactivity of the particles is attributed to the presence of a layer of adsorbed water on the particle surface. The amount of adsorbed water on the particle surface is strongly dependent on the extent of the reaction. This can be understood in terms of the increased hydrophilicity of calcium nitrate as compared to calcium carbonate. Data from experiments using a mass-calibrated Knudsen cell reactor showed the stoichiometry for the reaction determined from gas-phase species deviated from that expected from the balanced equation. Water adsorption on the particle surface and gases dissolved into the water layer appear to be the cause of this discrepancy. The measured uptake coefficient accounting for the BET area of the sample is determined to be 2.5±0.1×10-4 for HNO3 on CaCO3 under dry conditions and is found to increase in the presence of water vapor. Atmospheric implications of the results presented here are discussed.

  2. Nitric acid in the stratosphere based on Odin observations from 2001 to 2009 – Part 1: A global climatology

    Directory of Open Access Journals (Sweden)

    J. Urban

    2009-09-01

    Full Text Available The Sub-Millimetre Radiometer (SMR on board the Odin satellite, launched in February 2001, observes thermal emissions of stratospheric nitric acid (HNO3 originating from the Earth limb in a band centred at 544.6 GHz. Height-resolved measurements of the global distribution of nitric acid in the stratosphere were performed approximately on two observation days per week. An HNO3 climatology based on more than 7 years of observations from August 2001 to April 2009 covering the vertical range between typically ~19 and 45 km (~1.5–60 hPa or ~500–1800 K in terms of potential temperature was created. The study highlights the spatial and seasonal variation of nitric acid in the stratosphere, characterised by a pronounced seasonal cycle at middle and high latitudes with maxima during late fall and minima during spring, strong denitrification in the lower stratosphere of the Antarctic polar vortex during winter (the irreversible removal of NOy by the sedimentation of cloud particles containing HNO3, as well as large quantities of HNO3 formed every winter at high-latitudes in the middle and upper stratosphere. A strong inter-annual variability is observed in particular at high latitudes. A comparison with a stratospheric HNO3 climatology, based on over 7 years of UARS/MLS (Upper Atmosphere Research Satellite/Microwave Limb Sounder measurements from the 1990s, shows good consistency and agreement of the main morphological features in the potential temperature range ~465 to ~960 K, if the different characteristics of the data sets such as the better altitude resolution of Odin/SMR as well as the slightly different altitude ranges are considered. Odin/SMR reaches higher up and UARS/MLS lower down in the stratosphere. An overview from 1991 to 2009 of stratospheric nitric acid is provided (with a short gap between 1998 and 2001, if the global measurements of both experiments are taken together.

  3. Effect of Nitric Acid on the Low Fluorescing Performance of Drilling Fluid Lubricant Based Animal and Vegetable Oils

    Directory of Open Access Journals (Sweden)

    Feng-shan Zhou

    2013-01-01

    Full Text Available After synthesis of mixed fatty acid triethanolamine ester surfactant based on animal and vegetable mixed oils, the reaction solution was added into 4% (wt/wt liquid nitric acid or 9% (wt/wt solid nitric acid as eliminating fluorescent agent continuing to react from 1 to 2 hours. The low fluorescence lubricant named E167 for drilling fluid was prepared, in which maximum fluorescence intensity (Fmax was less than 10 in three-dimensional fluorescence spectra of excitation wavelength range. When the E167 was added into fresh water based drilling fluid at the dosage of 0.5% (wt/wt, the sticking coefficient reduced rate (ΔKf is 78% and the extreme pressure (E-P friction coefficient reduced rate (Δf is 79%. In the case of 4% brine mud with 0.5% (wt/wt E167 in it, the ΔKf and Δf are 75% and 62%, respectively. After the hot rolling ageing test 180°C × 16 h with the E167 was added into fresh water based drilling fluid at the dosage of 1% (wt/wt, the ΔKf and Δf are greater than 70%, which shows a much better lubrication properties of strong resistance to high temperature. The fresh water based drilling fluid which contains 1% (wt/wt E167 is almost nonfoaming even after hot rolling ageing 120°C × 16 h.

  4. Comparative analysis of the effect of pretreating aspen wood with aqueous and aqueous-organic solutions of sulfuric and nitric acid on its reactivity during enzymatic hydrolysis

    DEFF Research Database (Denmark)

    Dotsenko, Gleb; Osipov, D. O.; Zorov, I. N.;

    2016-01-01

    The effect of aspen wood pretreatment methods with the use of both aqueous solutions of sulfuric and nitric acids and aqueous-organic solutions (ethanol, butanol) of sulfuric acid (organosolv) on the limiting degree of conversion of this type of raw material into simple sugars during enzymatic...... of ground wood by 300–400%, compared to the initial raw material. Pretreatment with a 4.8% aqueous solution of nitric acid (125°C, 1.8 MPa, 10 min) is shown to be most effective, as it increases the reactivity of the ground aspen wood by more than 500%....

  5. Role of calcium signaling in the activation of mitochondrial nitric oxide synthase and citric acid cycle.

    Science.gov (United States)

    Traaseth, Nathaniel; Elfering, Sarah; Solien, Joseph; Haynes, Virginia; Giulivi, Cecilia

    2004-07-23

    An apparent discrepancy arises about the role of calcium on the rates of oxygen consumption by mitochondria: mitochondrial calcium increases the rate of oxygen consumption because of the activation of calcium-activated dehydrogenases, and by activating mitochondrial nitric oxide synthase (mtNOS), decreases the rates of oxygen consumption because nitric oxide is a competitive inhibitor of cytochrome oxidase. To this end, the rates of oxygen consumption and nitric oxide production were followed in isolated rat liver mitochondria in the presence of either L-Arg (to sustain a mtNOS activity) or N(G)-monomethyl-L-Arg (NMMA, a competitive inhibitor of mtNOS) under State 3 conditions. In the presence of NMMA, the rates of State 3 oxygen consumption exhibited a K(0.5) of 0.16 microM intramitochondrial free calcium, agreeing with those required for the activation of the Krebs cycle. By plotting the difference between the rates of oxygen consumption in State 3 with L-Arg and with NMMA at various calcium concentrations, a K(0.5) of 1.2 microM intramitochondrial free calcium was obtained, similar to the K(0.5) (0.9 microM) of the dependence of the rate of nitric oxide production on calcium concentrations. The activation of dehydrogenases, followed by the activation of mtNOS, would lead to the modulation of the Krebs cycle activity by the modulation of nitric oxide on the respiratory rates. This would ensue in changes in the NADH/NAD and ATP/ADP ratios, which would influence the rate of the cycle and the oxygen diffusion.

  6. [Effects of exogenous nitric oxide on physiological characteristics of longan (Dimocarpus longana) seedlings under acid rain stress].

    Science.gov (United States)

    Liu, Jian-fu; Wang, Ming-yuan; Yang, Chen; Zhu, Ai-jun

    2013-08-01

    This paper studied the effects of exogenous nitric oxide donor sodium nitroprusside (SNP) on the chlorophyll content, antioxidant enzyme activities, and osmotic regulation substances of longan (Dimocarpus longana 'Fuyan') seedlings under acid rain (pH 3.0) stress. Under the acid rain stress, the seedling leaf superoxide dismutase (SOD), peroxidase (POD) and catalase (CAT) activities and chlorophyll, soluble protein and soluble sugar contents decreased obviously, while the leaf malondialdedyde content had a remarkable increase, suggesting the toxic effect of the acid rain on the seedlings. Exogenous nitric oxide had dual nature on the physiological characteristics of longan seedlings under acid rain stress. Applying 0.1-0.5 mmol x L(-1) of SNP improved the SOD, POD and CAT activities and the chlorophyll, soluble protein and soluble sugar contents significantly, and decreased the malondialdedyde content. Low concentrations SNP reduced the oxidative damage caused by the acid rain stress, and 0.5 mmol x L(-1) of SNP had the best effect. Under the application of 0.5 mmol x L(-1) of SNP, the total chlorophyll, soluble protein, and soluble sugar contents and the SOD, POD and CAT activities increased by 76.0%, 107.0%, 216.1%, 150. 0%, 350.9% and 97.1%, respectively, and the malondialdedyde content decreased by 46.4%. It was suggested that low concentration (0.1-0.5 mmol x L(-1)) SNP could alleviate the toxic effect of acid rain stress on longan seedlings via activating the leaf antioxidant enzyme activities and reducing oxidative stress, while high concentration SNP (1.0 mmol x L(-1)) lowered the mitigation effect.

  7. Evaporation, Boiling and Bubbles

    Science.gov (United States)

    Goodwin, Alan

    2012-01-01

    Evaporation and boiling are both terms applied to the change of a liquid to the vapour/gaseous state. This article argues that it is the formation of bubbles of vapour within the liquid that most clearly differentiates boiling from evaporation although only a minority of chemistry textbooks seems to mention bubble formation in this context. The…

  8. Uric acid attenuates nitric oxide production by decreasing the interaction between endothelial nitric oxide synthase and calmodulin in human umbilical vein endothelial cells: a mechanism for uric acid-induced cardiovascular disease development.

    Science.gov (United States)

    Park, Jung-Hyun; Jin, Yoon Mi; Hwang, Soojin; Cho, Du-Hyong; Kang, Duk-Hee; Jo, Inho

    2013-08-01

    The elevated level of uric acid in the body is associated with increased risk of cardiovascular diseases, which is mediated by endothelial dysfunction. However, its underlying mechanism is not fully understood, although dysregulation of endothelial nitric oxide (NO) production is likely to be involved. Using human umbilical vascular endothelial cells (HUVEC), we explored the molecular mechanism of uric acid on endothelial NO synthase (eNOS) activity and NO production. Although high dose of uric acid (12mg/dl for 24h treatment) significantly decreased eNOS activity and NO production, it did not alter eNOS expression and phosphorylations at eNOS-Ser(1177), eNOS-Thr(495) and eNOS-Ser(114). Under this condition, we also found no alterations in the dimerization and acetylation of eNOS, compared with the control. Furthermore, uric acid did not change the activity of arginase II, an enzyme degrading l-arginine, a substrate of eNOS, and intracellular level of calcium, a cofactor for eNOS activation. We also found that uric acid did not alter xanthine oxidase activity, suggesting no involvement of xanthine oxidase-derived O2(-) production in the observed inhibitory effects. In vitro and in cell coimmunoprecipitation studies, however, revealed that uric acid significantly decreased the interaction between eNOS and calmodulin (CaM), an eNOS activator, although it did not change the intracellular CaM level. Like in HUVEC, uric acid also decreased eNOS-CaM interaction in bovine aortic EC. Finally, uric acid attenuated ionomycin-induced increase in the interaction between eNOS and CaM. This study suggests firstly that uric acid decreased eNOS activity and NO production through reducing the binding between eNOS and CaM in EC. Our result may provide molecular mechanism by which uric acid induces endothelial dysfunction.

  9. Ozone, nitric acid, and ammonia air pollution is unhealthy for people and ecosystems in southern Sierra Nevada, California

    Energy Technology Data Exchange (ETDEWEB)

    Cisneros, Ricardo, E-mail: rcisneros@fs.fed.u [USDA Forest Service, Pacific Southwest Region, 1600 Tollhouse Road, Clovis, CA 93611 (United States); Bytnerowicz, Andrzej, E-mail: abytnerowicz@fs.fed.u [USDA Forest Service, Pacific Southwest Research Station, 4955 Canyon Crest Dr., Riverside, CA 92507 (United States); Schweizer, Donald, E-mail: dschweizer@fs.fed.u [USDA Forest Service, Pacific Southwest Region, 1600 Tollhouse Road, Clovis, CA 93611 (United States); Zhong, Sharon, E-mail: zhongs@msu.ed [Department of Geography, Michigan State University, 116 Geography Building East, Lansing, MI 48824-1117 (United States); Traina, Samuel, E-mail: straina@ucmerced.ed [Environmental Systems Graduate Group, University of California Merced, 5200 North Lake Road, Merced, CA 95343 (United States); Bennett, Deborah H., E-mail: dhbennett@ucdavis.ed [Department of Public Health Sciences, University of California Davis, One Shields Avenue, TB 169 Davis, CA 95616 (United States)

    2010-10-15

    Two-week average concentrations of ozone (O{sub 3}), nitric acid vapor (HNO{sub 3}) and ammonia (NH{sub 3}) were measured with passive samplers during the 2002 summer season across the central Sierra Nevada Mountains, California, along the San Joaquin River drainage. Elevated concentrations of the pollutants were determined with seasonal means for individual sites ranging between 62 and 88 ppb for O{sub 3}, 1.0-3.8 {mu}g m{sup -3} for HNO{sub 3}, and 2.6-5.2 {mu}g m{sup -3} for NH{sub 3}. Calculated O{sub 3} exposure indices were very high, reaching SUM00-191 ppm h, SUM60-151 ppm h, and W126-124 ppm h. Calculated nitrogen (N) dry deposition ranged from 1.4 to 15 kg N ha{sup -1} for maximum values, and 0.4-8 kg N ha{sup -1} for minimum values; potentially exceeding Critical Loads (CL) for nutritional N. The U.S., California, and European 8 h O{sub 3} human health standards were exceeded during 104, 108, and 114 days respectively, indicating high risk to humans from ambient O{sub 3}. - Ozone concentrations remained unchanged while those of nitric acid vapor and ammonia decreased along the river drainage crossing the Sierra Nevada Mountains.

  10. Solvent extraction of uranium(VI) and thorium(IV) in nitric acid solution by N,N,N‘,N’—tetrabutyladipicamide

    Institute of Scientific and Technical Information of China (English)

    WangYou-Shao; BaoBo-Rong; 等

    1997-01-01

    N,N,N'N'-tetrabutyladipicamide(TBAA) has been synthesized,and applied to the extraction of U(VI) and Th(IV) from nitric acid solutions in a diluent composed of 0.50 volume fraction 1,2,4-trimethyl benzene (TMA) and 0.50 volume fraction kerosene(OK),The effects of the aueous nitric acid concentration,extractant concentration,slating-out agent (LiNO3) and temperature on extraction ability of TBAA for U(VI) and Th(IV) have been studied.Back Extraction of U(VI) and Th (IV) from organic phases were performed by dilute nitric acid.The compositions of extracted complexes,equilibrium constants and enthalpies of extraction reactions have also been estimated.The IR spectra of extraction of U(VI) and Th(IV) have been studied.

  11. Plasma levels of nitric oxide related amino acids in demented subjects with Down syndrome are related to neopterin concentrations.

    Science.gov (United States)

    Coppus, A M W; Fekkes, D; Verhoeven, W M A; Tuinier, S; van Duijn, C M

    2010-03-01

    Subjects with Down syndrome (DS) have abnormalities in virtually all aspects of the immune system and almost all will be affected with Alzheimer's disease (AD). It is thought that nitric oxide (NO) is involved in the pathophysiology of AD. In the present study, including a total of 401 elderly DS subjects, the spectrum of plasma amino acids and neopterin was investigated and related to development of AD. Concentrations of nearly all amino acids in DS subjects differed significantly from those of healthy controls. Neopterin was increased in DS subjects, especially in dementia. The production of NO as reflected by an increased citrulline/arginine ratio (Cit/Arg ratio) was enhanced during development of clinical dementia. Neopterin concentrations correlated to the Cit/Arg ratio only in the group of prevalent demented subjects (rho = 0.48, P = 0.006). The results of this study are suggestive for an increase in oxidative processes in DS subjects with AD.

  12. Aspects of subcooled boiling

    Energy Technology Data Exchange (ETDEWEB)

    Bankoff, S.G. [Northwestern Univ., Evanston, IL (United States)

    1997-12-31

    Subcooled boiling boiling refers to boiling from a solid surface where the bulk liquid temperature is below the saturation temperature (subcooled). Two classes are considered: (1) nucleate boiling, where, for large subcoolings, individual bubbles grow and collapse while remaining attached to the solid wall, and (2) film boiling, where a continuous vapor film separates the solid from the bulk liquid. One mechanism by which subcooled nucleate boiling results in very large surface heat transfer coefficient is thought to be latent heat transport within the bubble, resulting from simultaneous evaporation from a thin residual liquid layer at the bubble base, and condensation at the polar bubble cap. Another is the increased liquid microconvection around the oscillating bubble. Two related problems have been attacked. One is the rupture of a thin liquid film subject to attractive and repulsive dispersion forces, leading to the formation of mesoscopic drops, which then coalesce and evaporate. Another is the liquid motion in the vicinity of an oscillating contact line, where the bubble wall is idealized as a wedge of constant angle sliding on the solid wall. The subcooled film boiling problem has been attacked by deriving a general long-range nonlinear evolution equation for the local thickness of the vapor layer. Linear and weakly-nonlinear stability results have been obtained. A number of other related problems have been attacked.

  13. GLYCOLIC-NITRIC ACID FLOWSHEET DEMONSTRATION OF THE DWPF CHEMICAL PROCESS CELL WITH SLUDGE AND SUPERNATE SIMULANTS

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, D.; Stone, M.; Newell, J.; Best, D.; Zamecnik, J.

    2012-08-28

    Savannah River Remediation (SRR) is evaluating changes to its current Defense Waste Processing Facility (DWPF) flowsheet to improve processing cycle times. This will enable the facility to support higher canister production while maximizing waste loading. Higher throughput is needed in the Chemical Process Cell (CPC) since the installation of the bubblers into the melter has increased melt rate. Due to the significant maintenance required for the DWPF gas chromatographs (GC) and the potential for production of flammable quantities of hydrogen, reducing or eliminating the amount of formic acid used in the CPC is being developed. Earlier work at Savannah River National Laboratory has shown that replacing formic acid with an 80:20 molar blend of glycolic and formic acids has the potential to remove mercury in the SRAT without any significant catalytic hydrogen generation. This report summarizes the research completed to determine the feasibility of processing without formic acid. In earlier development of the glycolic-formic acid flowsheet, one run (GF8) was completed without formic acid. It is of particular interest that mercury was successfully removed in GF8, no formic acid at 125% stoichiometry. Glycolic acid did not show the ability to reduce mercury to elemental mercury in initial screening studies, which is why previous testing focused on using the formic/glycolic blend. The objective of the testing detailed in this document is to determine the viability of the nitric-glycolic acid flowsheet in processing sludge over a wide compositional range as requested by DWPF. This work was performed under the guidance of Task Technical and Quality Assurance Plan (TT&QAP). The details regarding the simulant preparation and analysis have been documented previously.

  14. GLYCOLIC-NITRIC ACID FLOWSHEET DEMONSTRATION OF THE DWPF CHEMICAL PROCESSING CELL WITH MATRIX SIMULANTS AND SUPERNATE

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, D.; Stone, M.; Newell, J.; Best, D.

    2012-05-07

    Savannah River Remediation (SRR) is evaluating changes to its current DWPF flowsheet to improve processing cycle times. This will enable the facility to support higher canister production while maximizing waste loading. Higher throughput is needed in the CPC since the installation of the bubblers into the melter has increased melt rate. Due to the significant maintenance required for the DWPF gas chromatographs (GC) and the potential for production of flammable quantities of hydrogen, reducing or eliminating the amount of formic acid used in the CPC is being developed. Earlier work at Savannah River National Laboratory has shown that replacing formic acid with an 80:20 molar blend of glycolic and formic acids has the potential to remove mercury in the SRAT without any significant catalytic hydrogen generation. This report summarizes the research completed to determine the feasibility of processing without formic acid. In earlier development of the glycolic-formic acid flowsheet, one run (GF8) was completed without formic acid. It is of particular interest that mercury was successfully removed in GF8, no formic acid at 125% stoichiometry. Glycolic acid did not show the ability to reduce mercury to elemental mercury in initial screening studies, which is why previous testing focused on using the formic/glycolic blend. The objective of the testing detailed in this document is to determine the viability of the nitric-glycolic acid flowsheet in processing sludge over a wide compositional range as requested by DWPF. This work was performed under the guidance of Task Technical and Quality Assurance Plan (TT and QAP). The details regarding the simulant preparation and analysis have been documented previously.

  15. New Inducible Nitric Oxide Synthase and Cyclooxygenase-2 Inhibitors, Nalidixic Acid Linked to Isatin Schiff Bases via Certain l-Amino Acid Bridges.

    Science.gov (United States)

    Naglah, Ahmed M; Ahmed, Atallah F; Wen, Zhi-Hong; Al-Omar, Mohamed A; Amr, Abd El-Galil E; Kalmouch, Atef

    2016-04-15

    A series of new Schiff bases were synthesized by condensation of isatins with the nalidixic acid-l-amino acid hydrazides. Prior to hydrazide formation, a peptide linkage has been prepared via coupling of nalidixic acid with appropriate l-amino acid methyl esters to yield 3a-c. The chemical structures of the new Schiff bases (5b and 5d-h) were confirmed by means of IR, NMR, mass spectroscopic, and elemental analyses. The anti-inflammatory activity of these Schiff bases was evaluated via measurement of the expressed inducible nitric oxide synthase (iNOS) and cyclooxygenase-2 (COX-2) in the lipopolysaccharide (LPS)-stimulated RAW264.7 macrophage cells model. The Schiff bases exhibited significant dual inhibitory effect against the induction of the pro-inflammatory iNOS and COX-2 proteins with variable potencies. However, they strongly down-regulated the iNOS expression to the level of 16.5% ± 7.4%-42.2% ± 19.6% compared to the effect on COX-2 expression (bases, relative to that of COX-2, seems to be a reflection of the combined suppressive effects exerted by their nalidixic acid, isatins (4a-c), and l-amino acid moieties against iNOS expression. These synthesized nalidixic acid-l-amino acid-isatin conjugates can be regarded as a novel class of anti-inflammatory antibacterial agents.

  16. Synergistic Action between Jasmonic Acid and Nitric Oxide in Inducing Matrine Accumulation of Sophora flavescens Suspension Cells

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Secondary metabolites not only play important ecological roles in plants but also are important pharmaceutical and source compounds for derivative synthesis. Production of plant secondary metabolites is believed to be controlled by the endogenous signal network of plants. However, the molecular basis is still largely unknown. Here we show that matrine production of Sophora flavescens Ait. cells treated with low levels of jasmonic acid (JA) and nitric oxide (NO) is significantly increased although treatment with low concentrations of JA or NO alone has no effects on matrine production, showing that JA and NO may act synergistically in triggering matrine production. Moreover, treatment with NO triggers lipoxygenase(LOX) activity and enhances JA levels of the cells, showing that NO may activate the endogenous JA biosynthesis of S.flavescens cells. External application of JA induces nitric oxide synthase-like activities and stimulates NO generation of S. flavescens cells, which suggests that JA may trigger NO generation of the cells. Thus, the results reveal a mutually amplifying reaction between JA and NO in S. flavescens cells. Furthermore, JA and NO inhibitors suppress not only the mutually amplifying reaction between JA and NO but also the synergistic effects of NO and JA on matrine production.Therefore, the data demonstrate that the synergistic action of JA and NO in inducing matrine production might be due to the mutually amplifying reaction between JA and NO in the cells.

  17. Triterpenoic Acids from Apple Pomace Enhance the Activity of the Endothelial Nitric Oxide Synthase (eNOS).

    Science.gov (United States)

    Waldbauer, Katharina; Seiringer, Günter; Nguyen, Dieu Linh; Winkler, Johannes; Blaschke, Michael; McKinnon, Ruxandra; Urban, Ernst; Ladurner, Angela; Dirsch, Verena M; Zehl, Martin; Kopp, Brigitte

    2016-01-13

    Pomace is an easy-accessible raw material for the isolation of fruit-derived compounds. Fruit consumption is associated with health-promoting effects, such as the prevention of cardiovascular disease. Increased vascular nitric oxide (NO) bioavailability, for example, due to an enhanced endothelial nitric oxide synthase (eNOS) activity, could be one molecular mechanism mediating this effect. To identify compounds from apple (Malus domestica Borkh.) pomace that have the potential to amplify NO bioavailability via eNOS activation, a bioassay-guided fractionation of the methanol/water (70:30) extract has been performed using the (14)C-L-arginine to (14)C-L-citrulline conversion assay (ACCA) in the human endothelium-derived cell line EA.hy926. Phytochemical characterization of the active fractions was performed using the spectrophotometric assessment of the total phenolic content, as well as TLC, HPLC-DAD-ELSD, and HPLC-MS analyses. Eleven triterpenoic acids, of which one is a newly discovered compound, were identified as the main constituents in the most active fraction, accompanied by only minor contents of phenolic compounds. When tested individually, none of the tested compounds exhibited significant eNOS activation. Nevertheless, cell stimulation with the reconstituted compound mixture restored eNOS activation, validating the potential of apple pomace as a source of bioactive components.

  18. Measurement of inorganic arsenic species in rice after nitric acid extraction by HPLC-ICPMS: verification using XANES.

    Science.gov (United States)

    Maher, W; Foster, S; Krikowa, F; Donner, E; Lombi, E

    2013-06-04

    The measurement of As species in rice is normally accomplished by extraction followed by HPLC-ICPMS analysis. This method, however, has not been comprehensively validated by comparing these speciation results with XANES, which does not require sample extraction, due to the challenge of conducting XANES analysis at very low As concentrations. In this study As speciation data using nitric acid extraction/HPLC-ICPMS and XANES are compared to verify the efficacy of using 2% v/v nitric acid extraction and HPLC-ICPMS to measure inorganic As, DMA, and MA in reference rice materials and common rice varieties obtainable in Australia. Total As and As species (As(III), As(V), DMA, and MA) concentrations measured in 8 reference materials were in agreement with published values. XANES analysis was performed on 5 samples having total As concentrations ranging from 0.198 to 0.335 μg g(-1). XANES results gave similar proportions of total As(III), As(V), and DMA to HPLC-ICPMS. XANES was able to distinguish two forms of As(III): As(III) and As(III)GSH. Total As concentrations in rice samples varied from 0.006 to 0.45 μg g(-1) As (n = 47) with a mean ± std of 0.127 ± 0.112 μg g(-1) As with most As present as inorganic species (63 ± 26%). DMA was found in nearly all the rice samples with the majority of samples containing concentrations below 0.05 μg g(-1) As while MA concentrations were negligible (<0.003 μg g(-1) As). Six rice varieties produced in Australia, China, and Spain all had elevated DMA concentrations (0.170-0.399 μg g(-1) As) that were correlated with total As concentrations (r(2) = 0.7518). In conclusion, comparison of As speciation by HPLC-ICPMS and XANES showed that similar As species were detected indicating the appropriateness of using 2% v/v nitric acid for extraction of rice prior to speciation. Common rice varieties obtainable in Australia generally have low As concentrations with most As present as inorganic As.

  19. Nucleate boiling heat transfer

    Energy Technology Data Exchange (ETDEWEB)

    Saiz Jabardo, J.M. [Universidade da Coruna (Spain). Escola Politecnica Superior], e-mail: mjabardo@cdf.udc.es

    2009-07-01

    Nucleate boiling heat transfer has been intensely studied during the last 70 years. However boiling remains a science to be understood and equated. In other words, using the definition given by Boulding, it is an 'insecure science'. It would be pretentious of the part of the author to explore all the nuances that the title of the paper suggests in a single conference paper. Instead the paper will focus on one interesting aspect such as the effect of the surface microstructure on nucleate boiling heat transfer. A summary of a chronological literature survey is done followed by an analysis of the results of an experimental investigation of boiling on tubes of different materials and surface roughness. The effect of the surface roughness is performed through data from the boiling of refrigerants R-134a and R-123, medium and low pressure refrigerants, respectively. In order to investigate the extent to which the surface roughness affects boiling heat transfer, very rough surfaces (4.6 {mu}m and 10.5 {mu}m ) have been tested. Though most of the data confirm previous literature trends, the very rough surfaces present a peculiar behaviour with respect to that of the smoother surfaces (Ra<3.0 {mu}m). (author)

  20. The Meteorology and Chemistry of High Nitric-Acid Episodes at the South Pole

    Science.gov (United States)

    Neff, William; Davis, Douglas

    2016-04-01

    Between 1998 and 2007, a series of field experiments carried out at the South Pole and with aircraft over a wider area revealed a very chemically active boundary layer overlying the east Antarctic ice sheet during the Austral summer. An early discovery was unexpectedly high concentrations of nitric acid (NO) at the South Pole. These were argued to be a result of the UV pholoysis of reactive nitrogen in surface and/or near-surface snow followed by subsequent confinement and non-linear HOx/NOx chemistry within a thin stable atmospheric boundary layer. The concentrations of NO also demonstrated daily, intraseasonal, as well as interannual variability as seen in the four field programs. This paper seeks to elucidate the interplay of large-to-small scale meteorology and chemistry at the South Pole that leads to highly variable NO concentrations and to examine boundary layer depth effects on NO in years when no direct measurements were available, in particular during the latest field program in 2006-2007. The importance of the South Pole is that it, unlike other high-latitude sites, has no diurnal cycle to disturb the evolution of the mostly stable boundary layer and its physics and chemistry. In the spring, as the solar elevation angle increases, nitrate photolysis rates increase. At the same time, the stratospheric vortex warms and with its breakup, the total column ozone increases leading to decreased photolysis rates. In addition, following the formation of the thermal tropopause in early spring, the tropospheric circulation over Antarctica changes dramatically, affecting the transport and dominant source regions for warm air and clouds arriving at the South Pole. The timing of the final warming ranged from early-November to mid-December for the four field experiment years. During the 30 days prior to the final increase in column ozone, as the thermal tropopause forms (~100 hPa), the winds at 300 hPa become bimodal, either along the eastern side of the Weddell Sea

  1. Laboratory Investigation of the Growth and Crystal Structure of Nitric Acid Hydrates by Transmission Electron Microscopy (TEM)

    Science.gov (United States)

    Blake, David F.; Chang, Sherwood (Technical Monitor)

    1994-01-01

    A great deal of recent laboratory work has focussed on the characterization of the nitric acid hydrates, thought to be present in type I Polar Stratospheric Clouds (PSCs). Phase relationships and vapor pressure measurements (1-3) and infrared characterizations (4-5) have been made. However, the observed properties of crystalline solids (composition, melting point, vapor pressure, surface reactivity, thermodynamic stability, extent of solid solution with other components, etc.) are controlled by their crystal structure. The only means of unequivocal structural identification for crystalline solids is diffraction (using electrons, X-rays, neutrons, etc.). Other observed properties of crystalline solids, such as their infrared spectra, their vapor pressure as a function of temperature, etc. yield only indirect information about what phases are present, their relative proportions, or whether they are crystalline or amorphous.

  2. Nitric-phosphoric acid etching effects on the surface chemical composition of CdTe thin film.

    Science.gov (United States)

    Irfan, Irfan; Ding, Huanjun; Xia, Wei; Lin, Hao; Tang, Ching W.; Gao, Yongli

    2009-03-01

    Nitric-phosphoric (NP) acid etching has been regarded as one of the most successful methods for the formation of low resistance back contact with the metal electrode in CdTe based solar cells. We report back surface chemical composition for eight different durations of NP etching of CdTe polycrystalline thin film. We studied the surfaces with x-ray photoemission spectroscopy (XPS), ultraviolet photoemission spectroscopy (UPS), inverse photoemission spectroscopy (IEPS) and atomic force microscopy (AFM). Etching dependence on the back surface composition and electronic structure was observed. Valence and conduction band shifts relative to the Fermi level of the system with different etching duration were analyzed. The sample was left in open ambient condition for three weeks and XPS data were obtained again in order to study the difference in surface chemical composition with the pristine CdTe film. Unetched and highly etched part of the sample were sputtered and the depth profile analyzed.

  3. Soft cutting of single-wall carbon nanotubes by low temperature ultrasonication in a mixture of sulfuric and nitric acids

    Science.gov (United States)

    Shuba, M. V.; Paddubskaya, A. G.; Kuzhir, P. P.; Maksimenko, S. A.; Ksenevich, V. K.; Niaura, G.; Seliuta, D.; Kasalynas, I.; Valusis, G.

    2012-12-01

    To decrease single-wall carbon nanotube (SWCNT) lengths to a value of 100-200 nm, aggressive cutting methods, accompanied by a high loss of starting material, are frequently used. We propose a cutting approach based on low temperature intensive ultrasonication in a mixture of sulfuric and nitric acids. The method is nondestructive with a yield close to 100%. It was applied to cut nanotubes produced in three different ways: gas-phase catalysis, chemical vapor deposition, and electric-arc-discharge methods. Raman and Fourier transform infrared spectroscopy were used to demonstrate that the cut carbon nanotubes have a low extent of sidewall degradation and their electronic properties are close to those of the untreated tubes. It was proposed to use the spectral position of the far-infrared absorption peak as a simple criterion for the estimation of SWCNT length distribution in the samples.

  4. Hydrofluoric-nitric-sulphuric-acid surface treatment of tungsten for carbon fibre-reinforced composite hybrids in space applications

    Science.gov (United States)

    Kanerva, M.; Johansson, L.-S.; Campbell, J. M.; Revitzer, H.; Sarlin, E.; Brander, T.; Saarela, O.

    2015-02-01

    Hybrid material systems, such as combinations of tungsten foils and carbon fibre-reinforced plastic (CFRP), are replacing metal alloy concepts in spacecraft enclosures. However, a good adhesion between the tungsten oxide scale and the epoxy resin used is required. Here, the effects of a hydrofluoric-nitric-sulphuric-acid (HFNS) treatment on tungsten oxides and subsequent adhesion to CFRP are analysed using atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and fracture testing. The work shows that HFNS treatment results in decreased oxygen content, over 50% thinner tungsten trioxide (WO3) layer and increased nano-roughness on thin tungsten foils. Fracture testing established a 39% increase in the average critical strain for tungsten-CFRP specimens after HFNS treatment was carried out on tungsten. The effect of the oxide scale modification regarding the critical strain energy release rate was ΔGc≈ 8.4 J/m2.

  5. Microstructure and Corrosion Behavior of Hf-40 Wt Pct Ti Alloy in Nitric Acid Medium for Reprocessing Applications

    Science.gov (United States)

    Jayaraj, J.; Ravi, K. R.; Mallika, C.; Kamachi Mudali, U.

    2016-09-01

    The Hf-40 wt pct Ti (Hf-Ti) alloy was developed for neutron poison application in the spent nuclear fuel reprocessing plant. The furnace-cooled Hf-Ti sample exhibited the microstructure comprising equiaxed-α, lamellar-α, and feathery-α. The water-quenched Hf-Ti sample confirmed the presence of lath and internally twinned martensite. In comparison to the furnace-cooled sample, low corrosion current density and passivation current density values obtained for the water-quenched Hf-Ti in 6 M HNO3 at 298 K (25 °C) indicated better passivation ability. The martensitic structure exhibited high hardness (660 HV) and negligible corrosion rate in 6 M nitric acid at 298 K (25 °C). X-ray photoelectron spectroscopic (XPS) analysis confirmed that passivation behavior of this alloy was due to the protective passive film composed of TiO2 and HfO2.

  6. Gene expression profiles of inducible nitric oxide synthase and cytokines in Leishmania major-infected macrophage-like RAW 264.7 cells treated with gallic acid

    NARCIS (Netherlands)

    Radtke, O.A.; Kiderlen, A.F.; Kayser, Oliver; Kolodziej, H

    2004-01-01

    The effects of gallic acid on the gene expressions of inducible nitric oxide synthase (iNOS) and the cytokines interleukin (IL)-1, IL-10, IL-12, IL-18, TNF-alpha, and interferon (IFN)-gamma were investigated by reverse-transcription polymerase chain reaction (RT-PCR). The experiments were performed

  7. Electrical and physicochemical properties of atomic-layer-deposited HfO{sub 2} film on Si substrate with interfacial layer grown by nitric acid oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seung Hyun [Department of Advanced Materials Engineering, Hanyang University, Ansan 15588 (Korea, Republic of); Seok, Tae Jun; Jin, Hyun Soo [Department of Materials Science & Chemical Engineering, Hanyang University, Ansan 15588 (Korea, Republic of); Kim, Woo-Byoung, E-mail: woo7838@dankook.ac.kr [Department of Energy Engineering, Dankook University, Cheonan 330-714 (Korea, Republic of); Park, Tae Joo, E-mail: tjp@hanyang.ac.kr [Department of Advanced Materials Engineering, Hanyang University, Ansan 15588 (Korea, Republic of); Department of Materials Science & Chemical Engineering, Hanyang University, Ansan 15588 (Korea, Republic of)

    2016-03-01

    Graphical abstract: - Highlights: • Ultrathin SiO{sub 2} interfacial layers grown using nitric acid oxidation and O{sub 3} oxidation were adopted at the interface of HfO{sub 2}/Si. • Higher physical density of interfacial layer grown using nitric acid oxidation resulted in the suppressed Si diffusion from substrate into the film. • The interface properties as well as permittivity of the film were improved by adoption of interfacial layer grown using nitric acid oxidation. - Abstract: The ultrathin SiO{sub 2} interfacial layer (IL) was adopted at the interface between atomic-layer-deposited HfO{sub 2} gate dielectric film and a Si substrate, which was grown using nitric acid oxidation (NAO) and O{sub 3} oxidation (OZO) prior to HfO{sub 2} film deposition. X-ray photoelectron spectroscopy result revealed that Si diffusion from the substrate into the film was suppressed for the film with NAO compared to that with OZO, which was attributed to the higher physical density of IL. The electrical measurement using metal–insulator–semiconductor devices showed that the film with NAO exhibited higher effective permittivity and lower densities of fixed charge and slow state at the interface. Furthermore, the leakage current density at an equivalent electrical thickness was lower for the film with NAO than OZO.

  8. Highly active and stable ion-exchanged Fe-Ferrierite catalyst for N2O decomposition under nitric acid tail gas conditions

    NARCIS (Netherlands)

    Melian Cabrera, Ignacio; Mentruit, C; Pieterse, JAZ; van den Brink, RW; Mul, G; Kapteijn, F; Moulijn, JA

    2005-01-01

    This communication reports on the excellent performance and durability of a wet ion-exchanged Fe-Ferrierite catalysts for N2O decomposition under conditions of nitric acid plants, especially in the presence of water (0.5% vol) and at a high space time W/F-0(N2O) = 900 kg(cat) s mol(-1). In contrast

  9. Highly active and stable ion-exchanged Fe–Ferrierite catalyst for N2O decomposition under nitric acid tail gas conditions

    NARCIS (Netherlands)

    Melián-Cabrera, I.; Mentruit, C.; Pieterse, J.A.Z.; Brink, R.W. van den; Mul, G.; Kapteijn, F.; Moulijn, J.A.

    2005-01-01

    This communication reports on the excellent performance and durability of a wet ion-exchanged Fe–Ferrierite catalysts for N2O decomposition under conditions of nitric acid plants, especially in the presence of water (0.5% vol) and at a high space time W/F0(N2O) = 900 kgcat s mol-1. In contrast to io

  10. Runaway behavior and thermally safe operation of multiple liquid–liquid reactions in the semi-batch reactor: The nitric acid oxidation of 2-octanol

    NARCIS (Netherlands)

    Woezik, van B.A.A.; Westerterp, K.R.

    2002-01-01

    The thermal runaway behavior of an exothermic, heterogeneous, multiple reaction system has been studied in a cooled semi-batch reactor. The nitric acid oxidation of 2-octanol has been used to this end. During this reaction, 2-octanone is formed, which can be further oxidized to unwanted carboxylic a

  11. Response of marine and freshwater algae to nitric acid and elevated carbon dioxide levels simulating environmental effects of bolide impact

    Science.gov (United States)

    Boston, P. J.

    1988-01-01

    One of the intriguing facets of the Cretaceous-Tertiary extinction is the apparently selective pattern of mortality amongst taxa. Some groups of organisms were severely affected and some remained relatively unscathed as they went through the K/T boundary. While there is argument concerning the exact interpretation of the fossil record, one of the best documented extinctions at the Cretaceous-Tertiary boundary is that of the calcareous nannoplankton. These organisms include coccolithic algae and foraminiferans. Attempts to explain their decline at the K/T boundary center around chemistry which could affect their calcium carbonate shells while leaving their silica-shelled cousins less affected or unaffected. Two environmental consequences of an extraterrestrial body impact which were suggested are the production of large quantities of nitrogen oxides generated by the shock heating of the atmosphere and the possible rise in CO2 from the dissolution of CaCO3 shells. Both of these phenomena would acidify the upper layers of the oceans and bodies of freshwater not otherwise buffered. The effects of nitric acid, carbon dioxide, or both factors on the growth and reproduction of calcareous marine coccoliths and non-calcareous marine and freshwater species of algae were considered. These experiments demonstrate that nitric acid and carbon dioxide have significant effects on important aspects of the physiology and reproduction of modern algae representative of extinct taxa thought to have suffered significant declines at the Cretaceous-Tertiary boundary. Furthermore, calcareous species showed more marked effects than siliceous species and marine species tested were more sensitive than freshwater species.

  12. Inhibition of nitric oxide synthase lowers fatty acid oxidation in preeclampsia-like mice at early gestational stage

    Institute of Scientific and Technical Information of China (English)

    MA Rui-qiong; SUN Min-na; YANG Zi

    2011-01-01

    Background Preeclampsia is one of hypertensive disorders in pregnancy. It is associated with abnormal lipid metabolism, including fatty acid oxidation metabolism. Long chain 3-hydroxyacyI-CoA dehydrogenase (LCHAD) plays an indispensable role in the oxidation of fatty acids. It has been reported that nitric oxide (NO) is one of the regulatory factors of the fatty acid oxidation pathway. The aim of this research was to investigate whether the nitric oxide synthase (NOS)inhibitor L-NAME may cause down-regulation of LCHAD in the pathogenesis of preeclampsia.Methods Pregnant wild-type (WT) mice were treated with L-NAME or normal saline (NS) during gestation days 7-18 (early group), days 11-18 (mid group) and days 16-18 (late group), and apoE-/- mice served as a control. Systolic blood pressure (SBP), urine protein, feto-placental outcome, plasma lipid levels and NO concentrations were measured, and the expression of mRNA and protein for LCHAD in placental tissue were determined by real-time polymerase chain reaction (RT-PCR) and Western blotting, respectively.Results In WT and apoE-/- mice, SBP and urinary protein increased following L-NAME injection. Fetal and placental weights and NO concentrations were reduced and total cholesterol, triglycerides and free fatty acid levels were increased in early and mid L-NAME groups in WT and apoE-/- mice, compared with the NS group. There was no significant difference between the late L-NAME group and NS group. RT-PCR and Western blotting analysis showed that the mRNA and protein levels of LCHAD expression were significantly down-regulated in the early and mid L-NAME groups but not in the late L-NAME group in the WT and apoE-/- mice compared with the corresponding NS groups.Conclusions Inhibition of NO in early and mid gestation in mice may cause hyperlipidemia and suppression of fatty acid oxidation, whereas preeclampsia-like conditions in late gestation may be a maternal vascular response to inhibition of NO.

  13. Solvent extraction of nitric acid,uranium(VI) and thorium(IV) by N,N,N',N'-tetrahexylsuccinylamide

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    A new kind of diamideN,N,N',N'-tetrahexylsuccinylamide (THSA)wassynthesized,characterized and used for the extraction of HNO3,U(VI) and Th(IV)in a diluent composed of 0.5 volume fraction1,2,4-trimethy benzene(TMB) and 0.5 volume fraction kerosene(OK).Extraction distribution coefficients of U(VI) and Th(IV) as functionsof aqueous nitric acid concentration, extractant concentration,temperature and salting-out agent (LiNO3) have been studied, and it is found that THSA as an extractant is superior to TBP for extraction ofU(VI) and Th(IV).Back extraction was also studied.At low acidity, themain adduct of THSA and HNO3 is HNO3.THSA.THSA.(HNO3)2 and THSA.(HNO3)3 are also found at high acidity.The compositions of extracted species, apparent equilibrium constants and enthalpies ofextraction reactions have also been calculated.

  14. Cross-talk between calcium-calmodulin and nitric oxide in abscisic acid signaling in leaves of maize plants

    Institute of Scientific and Technical Information of China (English)

    Jianrong Sang; Aying Zhang; Fan Lin; Mingpu Tan; Mingyi Jiang

    2008-01-01

    Using pharmacological and biochemical approaches,the signaling pathways between hydrogen peroxide (H2O2),calcium (Ca2+)-calmodulin (CAM),and nitric oxide (NO) in abscisic acid (ABA)-induced antioxidant defense were investigated in leaves of maize (Zea mays L.) plants.Treatments with ABA,H2O2,and CaCI2 induced increases in the generation of NO in maize mesophyll cells and the activity of nitric oxide synthase (NOS) in the cytosolic and microsomal fractions of maize leaves.However,such increases were blocked by the pretreatments with Ca2+ inhibitors and CaM antagonists.Meanwhile,pretreatments with two NOS inhibitors also suppressed the Ca2+-induced increase in the production of NO.On the other hand,treatments with ABA and the NO donor sodium nitroprusside (SNP) also led to increases in the concentration of cytosolic Ca2+ in protoplasts of mesophyll cells and in the expression of calmodulin 1 (CaMI) gene and the contents of CaM in leaves of maize plants,and the increases induced by ABA were reduced by the pretreatments with a NO scavenger and a NOS inhibitor.Moreover,SNP-induced increases in the expression of the antioxidant genes superoxide dismutase 4 (SOD4),cytosolic ascorbate peroxidase (cAPX),and glutathione reductase 1 (GRI) and the activities of the chloroplastic and cytosolic antioxidant enzymes were arrested by the pretreatments with Ca2+ inhibitors and CaM antagonists.Our results suggest that Ca2+-CaM functions both upstream and downstream of NO production,which is mainly from NOS,in ABA- and H2O2-induced antioxidant defense in leaves of maize plants.

  15. Ascorbic acid improves brachial artery vasodilation during progressive handgrip exercise in the elderly through a nitric oxide-mediated mechanism.

    Science.gov (United States)

    Trinity, Joel D; Wray, D Walter; Witman, Melissa A H; Layec, Gwenael; Barrett-O'Keefe, Zachary; Ives, Stephen J; Conklin, Jamie D; Reese, Van; Zhao, Jia; Richardson, Russell S

    2016-03-15

    The proposed mechanistic link between the age-related attenuation in vascular function and free radicals is an attractive hypothesis; however, direct evidence of free radical attenuation and a concomitant improvement in vascular function in the elderly is lacking. Therefore, this study sought to test the hypothesis that ascorbic acid (AA), administered intra-arterially during progressive handgrip exercise, improves brachial artery (BA) vasodilation in a nitric oxide (NO)-dependent manner, by mitigating free radical production. BA vasodilation (Doppler ultrasound) and free radical outflow [electron paramagnetic resonance (EPR) spectroscopy] were measured in seven healthy older adults (69 ± 2 yr) during handgrip exercise at 3, 6, 9, and 12 kg (∼13-52% of maximal voluntary contraction) during the control condition and nitric oxide synthase (NOS) inhibition via N(G)-monomethyl-L-arginine (L-NMMA), AA, and coinfusion of l-NMMA + AA. Baseline BA diameter was not altered by any of the treatments, while L-NMMA and L-NMMA + AA diminished baseline BA blood flow and shear rate. AA improved BA dilation compared with control at 9 kg (control: 6.5 ± 2.2%, AA: 10.9 ± 2.5%, P = 0.01) and 12 kg (control: 9.5 ± 2.7%, AA: 15.9 ± 3.7%, P vasodilation compared with control and when combined with AA eliminated the AA-induced improvement in BA vasodilation. Free radical outflow increased with exercise intensity but, interestingly, was not attenuated by AA. Collectively, these results indicate that AA improves BA vasodilation in the elderly during handgrip exercise through an NO-dependent mechanism; however, this improvement appears not to be the direct consequence of attenuated free radical outflow from the forearm.

  16. Reactions between water-soluble organic acids and nitrates in atmospheric aerosols: Recycling of nitric acid and formation of organic salts

    Science.gov (United States)

    Wang, Bingbing; Laskin, Alexander

    2014-03-01

    Atmospheric particles often include a complex mixture of nitrate and secondary organic materials accumulated within the same individual particles. Nitrate as an important inorganic component can be chemically formed in the atmosphere. For instance, formation of sodium nitrate (NaNO3) and calcium nitrate (Ca(NO3)2) occurs when nitrogen oxides and nitric acid (HNO3) react with sea salt and calcite, respectively. Organic acids contribute a significant fraction of photochemically formed secondary organics that can condense on the preexisting nitrate-containing particles. Here we present a systematic microanalysis study on chemical composition of laboratory-generated particles composed of water-soluble organic acids and nitrates (i.e., NaNO3 and Ca(NO3)2) using computer-controlled scanning electron microscopy with energy-dispersive X-ray microanalysis and Fourier transform infrared microspectroscopy. The results show that water-soluble organic acids can react with nitrates and release gaseous HNO3 during the dehydration process. These reactions are attributed to acid displacement of nitrate with weak organic acids driven by the evaporation of HNO3 into gas phase because of its relatively high volatility. The reactions result in significant nitrate depletion and formation of organic salts in mixed organic acids/nitrate particles that, in turn, may affect their physical and chemical properties relevant to atmospheric environment and climate. Airborne nitrate concentrations are estimated by thermodynamic calculations corresponding to various nitrate depletions in selected organic acids of atmospheric relevance. The results indicate a potential mechanism of HNO3 recycling that may further affect concentrations of gas and condensed phase species in the atmosphere and the heterogeneous reaction chemistry between them.

  17. New Inducible Nitric Oxide Synthase and Cyclooxygenase-2 Inhibitors, Nalidixic Acid Linked to Isatin Schiff Bases via Certain l-Amino Acid Bridges

    Directory of Open Access Journals (Sweden)

    Ahmed M. Naglah

    2016-04-01

    Full Text Available A series of new Schiff bases were synthesized by condensation of isatins with the nalidixic acid-l-amino acid hydrazides. Prior to hydrazide formation, a peptide linkage has been prepared via coupling of nalidixic acid with appropriate l-amino acid methyl esters to yield 3a–c. The chemical structures of the new Schiff bases (5b and 5d–h were confirmed by means of IR, NMR, mass spectroscopic, and elemental analyses. The anti-inflammatory activity of these Schiff bases was evaluated via measurement of the expressed inducible nitric oxide synthase (iNOS and cyclooxygenase-2 (COX-2 in the lipopolysaccharide (LPS-stimulated RAW264.7 macrophage cells model. The Schiff bases exhibited significant dual inhibitory effect against the induction of the pro-inflammatory iNOS and COX-2 proteins with variable potencies. However, they strongly down-regulated the iNOS expression to the level of 16.5% ± 7.4%–42.2% ± 19.6% compared to the effect on COX-2 expression (<56.4% ± 3.1% inhibition at the same concentration (10 μM. The higher iNOS inhibition activity of the tested Schiff bases, relative to that of COX-2, seems to be a reflection of the combined suppressive effects exerted by their nalidixic acid, isatins (4a–c, and l-amino acid moieties against iNOS expression. These synthesized nalidixic acid-l-amino acid-isatin conjugates can be regarded as a novel class of anti-inflammatory antibacterial agents.

  18. Production of 15N-enriched nitric acid (H15NO3

    Directory of Open Access Journals (Sweden)

    C. R. Sant Ana Filho

    2008-12-01

    Full Text Available Techniques that employ 15N have proved to be an important tool in many areas of the agronomic and biomedical sciences. Nevertheless, their use is limited by methodological difficulties and by the price of compounds in the international market. Nitric compounds (15NO3- have attracted the interest of researchers. However, these compounds are not currently produced in Brazil. Thus, in the present work H15NO3 was obtained from the oxidation of anhydrous 15NH3. The method we used differs from the industrial process in that the absorption tower is replaced with a polytetrafluoroethylene-lined, stainless-steel hydration reactor. The process output was evaluated based on the following parameters: reaction temperature; ratio of reagents; pressure and flow of 15NH3(g through the catalyst (Pt/Rh. The results showed that, at the best conditions (500 ºC; 50 % excess O2; 0.4 MPa; and 3.39 g.min-1 of 15NH3, a conversion percentage (N-15NH3 to N-15NO3- of 62.2 %, an overall nitrogen balance (N-15NH3 + N-15NO3- of 86.8 %, and purity higher than 99 % could be obtained.

  19. Solution extraction of several lanthanides from nitric acid with isohexyl-BTP in [Cnmim][NTf2] ionic liquid

    Institute of Scientific and Technical Information of China (English)

    赵龙; 董珍; 马国龙; 袁威津

    2015-01-01

    The extraction behavior of several lanthanides (La3+, Eu3+, Lu3+) from nitric acid (HNO3) solution was studied using a novel extraction system based on 2,6-bis(5,6-dihexyl-1,2,4-triazin-3-yl) pyridine (isohexyl-BTP) as extractant in 1-alkyl-3-me-thylimidazolium bis(trifluoromethylsufonyl)imide ([Cnmim][NTf2]) ionic liquid. Isohexyl-BTP in ionic liquids exhibited remarkably better extraction performance for lanthanides than that in octanol-dodecane (3:7 v/v) system. Lower HNO3 concentration and short alkyl chain length of [Cnmim]+were more favourable for removal of lanthanides. Besides, it was confirmed that isohexyl-BTP in ILs formed a 1:3 complex [Ln(BTP)3(NO3)n](3–n)+(n=0, 1) by slope analysis. In addition, [C2mim][NTf2] preferred to extract lanthanides via a cation exchange mechanism at lower acidity, which was proved via UV-Vis measurement. It was speculated that extraction mechanism shifted from cation exchange to neutral species extraction with increase in HNO3 concentration and alkyl chain length of [Cnmim]+due to the H+completion, NO3–inhibition and hydrophobicity of IL.

  20. Macroscopic, thermodynamic, kinetic and microscopic study of nitric acid pickling of Elektron 21 (EV31A magnesium alloy

    Directory of Open Access Journals (Sweden)

    Benjamin Mouls

    2014-12-01

    Full Text Available The study of pickling of the EL21T6 substrate in a nitric acid bath firstly provided knowledge of the influence of the different experimental parameters (concentration of acid, temperature and stirring of the solution in relation to the etching rate. This experimental part led to the choice of standard pickling (Tbath = 25 °C, moderate stirring (250 rpm, [HNO3] = 1.20 mol/L, duration of 2 min so as to obtain constant removal of material, even after several uses of the pickling bath. SEM observations also confirmed that in these operating conditions, pickling concerns both the grains of the matrix and the precipitates of type Mg3(Nd, Gd, leading to uniform removal of material from the surface. Working from a number of assumptions, thermodynamic and chemical kinetic studies then allowed a pickling mechanism to be proposed and led to obtaining values for the corresponding kinetic parameters (order of reaction, constant of mean rate, activation energy to be obtained.

  1. The Arabidopsis aleurone layer responds to nitric oxide, gibberellin, and abscisic acid and is sufficient and necessary for seed dormancy.

    Science.gov (United States)

    Bethke, Paul C; Libourel, Igor G L; Aoyama, Natsuyo; Chung, Yong-Yoon; Still, David W; Jones, Russell L

    2007-03-01

    Seed dormancy is a common phase of the plant life cycle, and several parts of the seed can contribute to dormancy. Whole seeds, seeds lacking the testa, embryos, and isolated aleurone layers of Arabidopsis (Arabidopsis thaliana) were used in experiments designed to identify components of the Arabidopsis seed that contribute to seed dormancy and to learn more about how dormancy and germination are regulated in this species. The aleurone layer was found to be the primary determinant of seed dormancy. Embryos from dormant seeds, however, had a lesser growth potential than those from nondormant seeds. Arabidopsis aleurone cells were examined by light and electron microscopy, and cell ultrastructure was similar to that of cereal aleurone cells. Arabidopsis aleurone cells responded to nitric oxide (NO), gibberellin (GA), and abscisic acid, with NO being upstream of GA in a signaling pathway that leads to vacuolation of protein storage vacuoles and abscisic acid inhibiting vacuolation. Molecular changes that occurred in embryos and aleurone layers prior to germination were measured, and these data show that both the aleurone layer and the embryo expressed the NO-associated gene AtNOS1, but only the embryo expressed genes for the GA biosynthetic enzyme GA3 oxidase.

  2. The influence of oxidation with nitric acid on the preparation and properties of active carbon enriched in nitrogen

    Energy Technology Data Exchange (ETDEWEB)

    Pietrzak, Robert [Laboratory of Coal Chemistry and Technology, Faculty of Chemistry, Adam Mickiewicz University, Grunwaldzka 6, 60-780 Poznan (Poland)], E-mail: pietrob@amu.edu.pl; Nowicki, Piotr; Wachowska, Helena [Laboratory of Coal Chemistry and Technology, Faculty of Chemistry, Adam Mickiewicz University, Grunwaldzka 6, 60-780 Poznan (Poland)

    2009-01-01

    The effect of oxidation by 20% nitric acid on the properties and performance of active carbons enriched with nitrogen by means of the reaction with urea in the presence of air has been studied. The study has been made on demineralised orthocoking coal and the carbonisates obtained from it at 600 or 700 deg. C, subjected to the processes of nitrogenation, oxidation and activation with KOH in different sequences. The amount of nitrogen introduced into the carbon with the aid of urea has been found to depend on the stage at which the process of nitrogenation was performed. The process of oxidation of the demineralised coal and the active carbon obtained from the former has been found to favour nitrogen introduction into the carbon structure. In the process of nitrogenation of the carbonisates the amount of nitrogen introduced has inversely depended on the temperature of carbonisation. The modifications of the processes permitted obtaining materials of different textural parameters, different acid-base character of the surface and different iodine sorption capacity.

  3. Determination of Uranyl Nitrate and Nitric Acid Based on Density and Conductivity Measurements

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>Measurement of the uranium and acidity plays an important role in process control of spent fuel reprocessing. The main chemical compositions including a mount of U solution in spent fuel reprocessing

  4. Numerical Investigation of Boiling

    Science.gov (United States)

    Sagan, Michael; Tanguy, Sebastien; Colin, Catherine

    2012-11-01

    In this work, boiling is numerically investigated, using two phase flow direct numerical simulation based on a level set / Ghost Fluid method. Nucleate boiling implies both thermal issue and multiphase dynamics issues at different scales and at different stages of bubble growth. As a result, the different phenomena are investigated separately, considering their nature and the scale at which they occur. First, boiling of a static bubble immersed in an overheated liquid is analysed. Numerical simulations have been performed at different Jakob numbers in the case of strong density discontinuity through the interface. The results show a good agreement on bubble radius evolution between the theoretical evolution and numerical simulation. After the validation of the code for the Scriven test case, interaction of a bubble with a wall is studied. A numerical method taking into account contact angle is evaluated by comparing simulations of the spreading of a liquid droplet impacting on a plate, with experimental data. Then the heat transfer near the contact line is investigated, and simulations of nucleate boiling are performed considering different contact angles values. Finally, the relevance of including a model to take into account the evaporation of the micro layer is discussed.

  5. Interannual variations of early winter Antarctic polar stratospheric cloud formation and nitric acid observed by CALIOP and MLS

    Science.gov (United States)

    Lambert, Alyn; Santee, Michelle L.; Livesey, Nathaniel J.

    2016-12-01

    We use satellite-borne measurements collected over the last decade (2006-2015) from the Aura Microwave Limb Sounder (MLS) and the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) to investigate the nitric acid distribution and the properties of polar stratospheric clouds (PSCs) in the early winter Antarctic vortex. Frequently, at the very start of the winter, we find that synoptic-scale depletion of HNO3 can be detected in the inner vortex before the first lidar detection of geophysically associated PSCs. The generation of "sub-visible" PSCs can be explained as arising from the development of a solid particle population with low number densities and large particle sizes. Assumed to be composed of nitric acid trihydrate (NAT), the sub-visible PSCs form at ambient temperatures well above the ice frost point, but also above the temperature at which supercooled ternary solution (STS) grows out of the background supercooled binary solution (SBS) distribution. The temperature regime of their formation, inferred from the simultaneous uptake of ambient HNO3 into NAT and their Lagrangian temperature histories, is at a depression of a few kelvin with respect to the NAT existence threshold, TNAT. Therefore, their nucleation requires a considerable supersaturation of HNO3 over NAT, and is consistent with a recently described heterogeneous nucleation process on solid foreign nuclei immersed in liquid aerosol. We make a detailed investigation of the comparative limits of detection of PSCs and the resulting sequestration of HNO3 imposed by lidar, mid-infrared, and microwave techniques. We find that the temperature history of air parcels, in addition to the local ambient temperature, is an important factor in the relative frequency of formation of liquid/solid PSCs. We conclude that the initiation of NAT nucleation and the subsequent development of large NAT particles capable of sedimentation and denitrification in the early winter do not emanate from an ice

  6. Development of a Technology for Treating Wastewater Contaminated with Nitric Acid

    Directory of Open Access Journals (Sweden)

    Liz Mabel Ríos Hidalgo

    2013-01-01

    Full Text Available The production process of nitroaromatic hazardous compounds, with the generation of acidic wastewater, represents a significant danger for the health and safety of the workers and the environment. The present study is focused on the development of an efficient installation to treat acidic wastewater resulting from the synthesis process of nitroaromatic compound, considering workers safety and environmental criteria. In this research, a detailed study of the different alternatives that can be used for effective and safe treatment of acidic wastewater was performed. The analysis of several technological schemes for the acidic wastewaters neutralization and the selection of the most feasible alternative from a technical-economic point of view were carried out. The simulation and mathematical modeling developed in this research represent a significant advance in the knowledge of this process for working in a much more secure form. The technological scheme of the process was defined, and the design of the main and auxiliary equipment as well as the piping system was carried out using different computational programs. Finally, this paper proposes a technological design for the treatment of acidic wastewater generated by the production process of nitroaromatic compound, which represents the basic criteria for the further design, construction, and equipment installation of the plant.

  7. Interactions of Gas-Phase Nitric/Nitrous Acids and Primary Organic Aerosol in the Atmosphere of Houston, TX

    Science.gov (United States)

    Ziemba, L. D.; Griffin, R. J.; Dibb, J. E.; Anderson, C. H.; Whitlow, S. I.; Lefer, B. L.; Flynn, J.; Rappenglück, B.

    2007-12-01

    Concentrations of aerosol and gas-phase pollutants were measured on the roof of an 18-story building during the Texas Air Quality Study II Radical and Aerosol Measurement Project (TRAMP) from August 15 through September 28, 2006. Aerosol measurements included size-resolved, non-refractory mass concentrations of ammonium, nitrate, sulfate, chloride, and organic aerosol in submicron particles using an Aerodyne quadrupole aerosol mass spectrometer (Q-AMS). Particulate water-soluble organic carbon (PWSOC) was quantified using a mist chamber/total organic carbon analysis system. Concentration data for gas-phase pollutants included those for nitric acid (HNO3), nitrous acid (HONO), and hydrochloric acid (HCl) collected using a mist chamber/ion chromatographic technique, oxides of nitrogen (NOx) collected using a chemiluminescent method, and carbon monoxide (CO) collected using an infrared gas correlation wheel instrument. Coincident increases in nitrate and organic aerosol mass concentrations were observed on many occasions throughout the measurement campaign, most frequently during the morning rush hour. Based on the lack of organic aerosol processing (defined by the ratio of m/z = 44/57 in the Q-AMS spectra), strong correlation with NOx and CO, and a lack of significant increase in PWSOC concentration, the spikes in organic aerosol were likely associated with primary organic aerosol (POA). During these events, gas-phase HNO3 concentration decreases were observed simultaneously with increases in gas-phase HONO concentrations. These data likely indicate uptake of HNO3 and subsequent heterogeneous conversion to HONO involving POA. Preliminary calculations show that HNO3 partitioning could account for the majority of the observed HONO and aerosol nitrate concentrations during these events. Q-AMS chloride and HCl data also indicate uptake of chloride by particles during these events. This phenomenon was also observed during the night, but these nocturnal events were less

  8. Kinetics study on the dissolution of UO2 particles by microwave and conventional heating in 4 mol/L nitric acid

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The dissolution of UO2 particles in 4 mol·L-1 nitric acid medium at temperatures of 90-110℃ by mi- crowave heating and conventional heating has been investigated, respectively. It is found that the dissolution ratios of UO2 particles by microwave heating were 10%-40% higher than that by conven- tional heating. Kinetics research shows that the dissolution of UO2 particles in 4 mol·L-1 nitric acid is controlled by the diffusion control model for microwave heating and by the surface reaction control model for conventional heating. The diffusion control model for the dissolution of UO2 particles by mi- crowave heating could be explained by the diffuseness on the surface of UO2 particles.

  9. [Determination of nine hazardous elements in textiles by inductively coupled plasma optical emission spectrometer after microwave-assisted dilute nitric acid extraction].

    Science.gov (United States)

    Chen, Fei; Xu, Dian-dou; Tang, Xiao-ping; Cao, Jing; Liu, Ya-ting; Deng, Jian

    2012-01-01

    Textiles are easily contaminated by heavy metals in the course of processing. In order to monitor the quality of textiles, a new method was developed for simultaneous determination of arsenic, antimony, lead, cadmium, chromium, cobalt, copper, nickel and mercury in textiles by inductively coupled plasma optical emission spectrometry (ICP-OES) after microwave-assisted dilute nitric acid extraction. After optimizing extraction conditions, we ultimately selected 5% nitric acid as extractant and 5 min as extraction time with the extraction temperature of 120 degrees C and instrument power of 400W in the microwave-assisted extraction procedure. Nine hazardous elements were detected sequentially by ICP-OES. The results showed that the detection limits were 0.3-15 microg x L(-1) and the recoveries 73.6%-105% with the RSDs (n = 3) of 0.1%-3%. The proposed method was successfully used to determine nine elements in cotton, wool, terylene and acrylic.

  10. Improvement of microwave-assisted digestion of milk powder with diluted nitric acid using oxygen as auxiliary reagent

    Energy Technology Data Exchange (ETDEWEB)

    Bizzi, Cezar A. [Departamento de Quimica, Universidade Federal de Santa Maria, 97105-900, Santa Maria, RS (Brazil); Instituto Nacional de Ciencia e Tecnologia de Bioanalitica, Campinas, SP (Brazil); Barin, Juliano S. [Departamento de Tecnologia e Ciencia dos Alimentos, Universidade Federal de Santa Maria, 97105-900, Santa Maria, RS (Brazil); Garcia, Edivaldo E. [Departamento de Quimica, Universidade Estadual de Maringa, 87100-900, Maringa, PR (Brazil); Nobrega, Joaquim A. [Departamento de Quimica, Universidade Federal de Sao Carlos, 13565-905, Sao Carlos, SP (Brazil); Dressler, Valderi L. [Departamento de Quimica, Universidade Federal de Santa Maria, 97105-900, Santa Maria, RS (Brazil); Instituto Nacional de Ciencia e Tecnologia de Bioanalitica, Campinas, SP (Brazil); Flores, Erico M.M., E-mail: ericommf@gmail.com [Departamento de Quimica, Universidade Federal de Santa Maria, 97105-900, Santa Maria, RS (Brazil); Instituto Nacional de Ciencia e Tecnologia de Bioanalitica, Campinas, SP (Brazil)

    2011-05-15

    The feasibility of using diluted HNO{sub 3} solutions under oxygen pressure for decomposition of whole and non-fat milk powders and whey powder samples has been evaluated. Digestion efficiency was evaluated by determining the carbon content in solution (digests) and the determination of Ca, Cd, Cu, Fe, K, Mg, Mn, Mo, Na, Pb and Zn was performed by inductively coupled plasma optical emission spectrometry and Hg by chemical vapor generation coupled to inductively coupled plasma mass spectrometry. Samples (up to 500 mg) were digested using HNO{sub 3} solutions (1 to 14 mol L{sup -1}) and the effect of oxygen pressure was evaluated between 2.5 and 20 bar. It was possible to perform the digestion of 500 mg of milk powder using 2 mol L{sup -1} HNO{sub 3} with oxygen pressure ranging from 7.5 to 20 bar with resultant carbon content in digests lower than 1700 mg L{sup -1}. Using optimized conditions, less than 0.86 mL of concentrated nitric acid (14 mol L{sup -1}) was enough to digest 500 mg of sample. The accuracy was evaluated by determination of metal concentrations in certified reference materials, which presented an agreement better than 95% (Student's t test, P < 0.05) for all the analytes.

  11. Recovery of Nickel from Reformer Catalysts of Direct Reduction, Using the Pressurized Dissolving Method in Nitric Acid

    Directory of Open Access Journals (Sweden)

    B. Abrar

    2016-10-01

    Full Text Available In the process of direct reduction of iron pellet and production of sponge iron, NiO/Al2O3 act as a catalyst for the generation of carbon monoxide and hydrogen by vapor and natural gas. As an expensive material used in MIDREX method for steel units, this type of catalyst has major environmental problems after accumulation. The steel industry in Iran hopes to employ the MIDREX technique for the 80 percent of the 50 million tons of steel. Thus, the problem of spent catalysts will become a serious environmental challenge. Through the hydrometallurgy method, the present study investigates a possible solution to the problem of catalyst depot (due to heavy metals such as nickel via nickel recovery, which may increase the possibility of selling or re-using the precious and expensive metal. The present research studied the Nickel recovery from spent catalysts of NiO/Al2O¬3 used in reduction gas reliefs of the production of sponge iron unit. In this study, the parameters of temperature, concentration, time and Rpm were studied using pressurized dissolving method. 100% efficiency was achieved at 140 °C for 120 minutes, nitric acid concentration of 1.5 mm, Rpm of 600 and 40 s/l 40 grams per liter.

  12. Nitric oxide involved in signal transduction of Jasmonic acid-induced stomatal closure of Vicia faba L.

    Institute of Scientific and Technical Information of China (English)

    LIU Xin; SHI Wuliang; ZHANG Shuqiu; LOU Chenghou

    2005-01-01

    Nitric oxide (NO) and Jasmonic acid (JA) are two key signaling molecules involved in many and diverse biological pathways in plants. Growing evidence suggested that NO signaling interacts with JA signaling. In this work, Our experiment showed that NO exists in guard cell of Vicia faba L., and NO is involved in signal transduction of JA- induced stomata closuring: (ⅰ) JA enhances NO synthesis in guard cell; (ⅱ) both JA and NO induced stomatal closure, and had dose response to their effects; (ⅲ) there are synergetic correlation between JA and lower NO concentration in regulation of stomatal movement; (ⅳ) JA-induced stomatal closure was largely prevented by 2-phenyl-4,4,5,5-tetrame- thylimidazoline-1-oxyl-3-oxide (PTIO), a specific NO scavenger. An inhibitor of NO synthase (NOS) in mammalian cells, NG-nitro-L-Arg-methyl eater (L-NAME) also inhibits plant NOS, repressing JA-induced NO generation and JA-induced stomatal closure. We presumed that NO mainly comes from NOS after JA treatment.

  13. Synergistic extraction of U(VI) and Th(IV) from nitric acid media with HBMPPT and TBP in toluene

    Institute of Scientific and Technical Information of China (English)

    YUShaoning; BAOBorong

    1999-01-01

    The sysnergistic extraction of U(VI)and Th(IV) from nitric acid solution by HBMPPT(4-benzoyl-2,4-dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione) and TBP( tributylphosphate)in toluene was studied.The extraction ability of HBMPPT for U(VI) and Th(IV) was not so high.but when a little TBP was added in,the ability to extract U(VI) and Th(IV) was improved.The extracted complexes may be presented as UO2NO3.BMPPT.TBP and UO2(BMPPT)2.TBP for U(VI).and Th(NO3)3.BMPPT.TBP and Th(NO3)2(BMPPT)2.TBP for Th(IV),respectively,in the synergistic extraction system.The synergistic effect of HBMPPT and TBP makes the separation cofeeicient of U(VI)/Th (IV) or U(VI)/Eu(Ⅲ) reach a high value.

  14. 硝酸乙醇法测定纤维素含量%Determination the content of cellulose by nitric acid-ethanol method

    Institute of Scientific and Technical Information of China (English)

    王林风; 程远超

    2011-01-01

    根据秸秆乙醇的工艺特点,对硝酸乙醇法测定玉米秸秆、小麦秸秆、稻草及其预处理后物料的纤维素含量进行了研究.优化了粉碎时长、硝酸-乙醇混合液处理遍数、试样粒度及抽滤漏斗孔径四个参数.确定了优化后的测定方法:秸秆试样粉碎时长15 s,硝酸-乙醇混合液处理4遍,粒度40~60目,使用G2玻璃砂芯漏斗.秸秆预处理后物料试样粉碎时长3 s,硝酸-乙醇混合液处理3遍,粒度40~60目,使用G3玻璃砂芯漏斗.%The contents of cellulose of corn stalk, wheat straw, rice straw and the pretreated sample of straws have been researched by nitric acid-ethanol methodology according to the characteristics of straws biofuel ethanol. Four parameters as the duration of comminuting sample, the times of treating sample by nitric acid-ethanol liquid mixture, the particle size of sample and the aperture of tundish for sucking filtration have been optimized. The optimized pev-rameters: for straw sample, comminut 15 s, treat by nitric acid-ethanol liquid mixture 4 times, sample aperture 40 - 60 mesh, use G2 glass sand core tundish. For pretreated sample, comminut 3 s, treat by nitric acid-ethanol liquid mixture 3 times, sample aperture 40 - 60 mesh, use G3 glass sand core tundish.

  15. Interaction of Polyamines, Abscisic Acid, Nitric Oxide, and Hydrogen Peroxide under Chilling Stress in Tomato (Lycopersicon esculentum Mill.) Seedlings.

    Science.gov (United States)

    Diao, Qiannan; Song, Yongjun; Shi, Dongmei; Qi, Hongyan

    2017-01-01

    Polyamines (PAs) play a vital role in the responses of higher plants to abiotic stresses. However, only a limited number of studies have examined the interplay between PAs and signal molecules. The aim of this study was to elucidate the cross-talk among PAs, abscisic acid (ABA), nitric oxide (NO), and hydrogen peroxide (H2O2) under chilling stress conditions using tomato seedlings [(Lycopersicon esculentum Mill.) cv. Moneymaker]. The study showed that during chilling stress (4°C; 0, 12, and 24 h), the application of spermidine (Spd) and spermine (Spm) elevated NO and H2O2 levels, enhanced nitrite reductase (NR), nitric oxide synthase (NOS)-like, and polyamine oxidase activities, and upregulated LeNR relative expression, but did not influence LeNOS1 expression. In contrast, putrescine (Put) treatment had no obvious impact. During the recovery period (25/15°C, 10 h), the above-mentioned parameters induced by the application of PAs were restored to their control levels. Seedlings pretreated with sodium nitroprusside (SNP, an NO donor) showed elevated Put and Spd levels throughout the treatment period, consistent with increased expression in leaves of genes encoding arginine decarboxylase (LeADC. LeADC1), ornithine decarboxylase (LeODC), and Spd synthase (LeSPDS) expressions in tomato leaves throughout the treatment period. Under chilling stress, the Put content increased first, followed by a rise in the Spd content. Exogenously applied SNP did not increase the expression of genes encoding S-adenosylmethionine decarboxylase (LeSAMDC) and Spm synthase (LeSPMS), consistent with the observation that Spm levels remained constant under chilling stress and during the recovery period. In contrast, exogenous Put significantly increased the ABA content and the 9-cis-epoxycarotenoid dioxygenase (LeNCED1) transcript level. Treatment with ABA could alleviate the electrolyte leakage (EL) induced by D-Arg (an inhibitor of Put). Taken together, it is concluded that, under chilling

  16. 六硝基茋在硝酸中的溶解度测定及关联%Solubility Measurement and Correlation of Hexanitrostilbene in Nitric Acid

    Institute of Scientific and Technical Information of China (English)

    许元刚; 李冬雪

    2014-01-01

    The solubility of 2 ,2',4 ,4',6 ,6'-Hexanitrostilbene , varied with concentration of nitric acid under 25℃, was measured using the laser monitor technique.The experimental data were correlated with the ( CNIBS )/Redlich -Kister empirical equation.The results showed that the solubility of HNS in nitric acid increased with concentration of nitric acid, and the predicted data by empirical equation had good agreement with the experiment data.%采用激光监测技术,测定了25℃下六硝基茋在不同浓度硝酸中的溶解度,用( CNIBS)/Redlich-Kister经验方程对实验数据进行了关联。结果表明六硝基茋在硝酸中的溶解度随硝酸浓度的增大而增加,用( CNIBS )/Redlich-Kister方程预测的溶解度值与实验值有较好的吻合。

  17. Geysering in boiling channels

    Energy Technology Data Exchange (ETDEWEB)

    Aritomi, Masanori; Takemoto, Takatoshi [Tokyo Institute of Technology, Tokyo (Japan); Chiang, Jing-Hsien [Japan NUS Corp. Ltd., Toyko (Japan)] [and others

    1995-09-01

    A concept of natural circulation BWRs such as the SBWR has been proposed and seems to be promising in that the primary cooling system can be simplified. The authors have been investigating thermo-hydraulic instabilities which may appear during the start-up in natural circulation BWRs. In our previous works, geysering was investigated in parallel boiling channels for both natural and forced circulations, and its driving mechanism and the effect of system pressure on geysering occurrence were made clear. In this paper, geysering is investigated in a vertical column and a U-shaped vertical column heated in the lower parts. It is clarified from the results that the occurrence mechanism of geysering and the dependence of system pressure on geysering occurrence coincide between parallel boiling channels in circulation systems and vertical columns in non-circulation systems.

  18. Nitro-fatty acids in plant signaling: New key mediators of nitric oxide metabolism

    Directory of Open Access Journals (Sweden)

    Capilla Mata-Pérez

    2017-04-01

    Full Text Available Recent studies in animal systems have shown that NO can interact with fatty acids to generate nitro-fatty acids (NO2-FAs. They are the product of the reaction between reactive nitrogen species and unsaturated fatty acids, and are considered novel mediators of cell signaling based mainly on a proven anti-inflammatory response. Although these signaling mediators have been described widely in animal systems, NO2-FAs have scarcely been studied in plants. Preliminary data have revealed the endogenous presence of free and protein-adducted NO2-FAs in extra-virgin olive oil (EVOO, which appear to be contributing to the cardiovascular benefits associated with the Mediterranean diet. Importantly, new findings have displayed the endogenous occurrence of nitro-linolenic acid (NO2-Ln in the model plant Arabidopsis thaliana and the modulation of NO2-Ln levels throughout this plant's development. Furthermore, a transcriptomic analysis by RNA-seq technology established a clear signaling role for this molecule, demonstrating that NO2-Ln was involved in plant-defense response against different abiotic-stress conditions, mainly by inducing the chaperone network and supporting a conserved mechanism of action in both animal and plant defense processes. Thus, NO2-Ln levels significantly rose under several abiotic-stress conditions, highlighting the strong signaling role of these molecules in the plant-protection mechanism. Finally, the potential of NO2-Ln as a NO donor has recently been described both in vitro and in vivo. Jointly, this ability gives NO2-Ln the potential to act as a signaling molecule by the direct release of NO, due to its capacity to induce different changes mediated by NO or NO-related molecules such as nitration and S-nitrosylation, or by the electrophilic capacity of these molecules through a nitroalkylation mechanism. Here, we describe the current state of the art regarding the advances performed in the field of NO2-FAs in plants and their

  19. Oscillate boiling from microheaters

    Science.gov (United States)

    Li, Fenfang; Gonzalez-Avila, S. Roberto; Nguyen, Dang Minh; Ohl, Claus-Dieter

    2017-01-01

    We report about an intriguing boiling regime occurring for small heaters embedded on the boundary in subcooled water. The microheater is realized by focusing a continuous wave laser beam to about 10 μ m in diameter onto a 165-nm-thick layer of gold, which is submerged in water. After an initial vaporous explosion a single bubble oscillates continuously and repeatedly at several 100 kHz albeit with constant laser power input. The microbubble's oscillations are accompanied with bubble pinch-off, leading to a stream of gaseous bubbles in the subcooled water. The self-driven bubble oscillation is explained with a thermally kicked oscillator caused by surface attachment and by the nonspherical collapses. Additionally, Marangoni stresses induce a recirculating streaming flow which transports cold liquid towards the microheater, reducing diffusion of heat along the substrate and therefore stabilizing the phenomenon to many million cycles. We speculate that this oscillate boiling regime may overcome the heat transfer thresholds observed during the nucleate boiling crisis and offers a new pathway for heat transfer under microgravity conditions.

  20. Liquid-liquid extraction of palladium(II) from nitric acid by bis(2-ethylhexyl) sulphoxide

    Energy Technology Data Exchange (ETDEWEB)

    Shukla, J.P. (Radiochemistry Division, Bhabha Atomic Research Centre, Trombay, Bombay 400085 (India)); Singh, R.K.; Sawant, S.R.; Varadarajan, N. (Power Reactor Fuel Reprocessing Plant, Bhabha Atomic Research Centre, Trombay, Bombay 400085 (India))

    1993-04-15

    The extraction of palladium(II) nitrate by bis(2-ethylhexyl) sulphoxide (BESO) was evaluated over a wide range of acidity, and BESO was shown to have a strong extraction ability toward this thiophilic 'soft' metal. Essentially quantitative extraction of trace and macro amounts of palladium is easily accomplished from about 8 M HNO 8 M HNO[sub 3] down to pH 2 solutions by 0.2 M BESO into toluene. Optimum conditions such as aqueous phase acidity, solvent, period of equilibration, aqueous to organic phase ratios, reagent concentration and strippant were established for the selective and reversible extraction and separation of palladium. Slope analyses applied to Pd(II) distribution experiments from nitrate solutions showed a predominant formation of the solvated organic phase complex Pd(NO[sub 3])[sub 2].2BESO. Recovery of the extractant from loaded palladium is easily accomplished by using sodium thiosulphate or a mixture of 2 M sodium carbonate+0.5 M ammonia solution. The extracted complex was characterized by elemental analysis and IR and UV-visible spectrometry, and its composition was confirmed to be Pd(NO[sub 3])[sub 2].2BESO

  1. Green Design on the Reaction of Copper and Nitric Acid%铜与硝酸反应的绿色化设计

    Institute of Scientific and Technical Information of China (English)

    张玉贞; 李先栓

    2011-01-01

    To achieve green ideas on chemical experiment teaching has to hold two critical points: One is that chemical reactions of harmful volatile materials must be carried out in completely sealed condition; The other is that products need harmlessly be treated for environment. In this paper, using U pipe, the reaction of copper and concentrated/dilute nitric acid can be guaranteed in sealed surroundings and the tail gas was harmlessly treated. The reaction of nitric oxide and concentrated nitric acid demonstrated that the gas product of the reaction of copper and concentrated nitric acid was nitrogen dioxide, which can provide strong criterion for correcting students' wrong ideas.%化学实验教学实现绿色化思想的关键有两点:一是挥发有害物质的化学反应在完全密封状态下进行;二是实验产物的无害化处理.利用U型管巧妙设计,可使铜与浓、稀硝酸反应的毒气实验在密闭环保中进行,同时达到了绿色化尾气处理利用NO与浓HNO3反应,可证明铜与浓硝酸反应为什么生成的是NO2而不是NO,从事实上为学生纠错提供了有力判据.

  2. Boiling incipience and convective boiling of neon and nitrogen

    Science.gov (United States)

    Papell, S. S.; Hendricks, R. C.

    1977-01-01

    Forced convection and subcooled boiling heat transfer data for liquid nitrogen and liquid neon were obtained in support of a design study for a 30 tesla cryomagnet cooled by forced convection of liquid neon. This design precludes nucleate boiling in the flow channels as they are too small to handle vapor flow. Consequently, it was necessary to determine boiling incipience under the operating conditions of the magnet system. The cryogen data obtained over a range of system pressures, fluid flow rates, and applied heat fluxes were used to develop correlations for predicting boiling incipience and convective boiling heat transfer coefficients in uniformly heated flow channels. The accuracy of the correlating equations was then evaluated. A technique was also developed to calculate the position of boiling incipience in a uniformly heated flow channel. Comparisons made with the experimental data showed a prediction accuracy of plus or minus 15 percent

  3. The ν_3 and ν_4 Bands of Nitric Acid (HNO_3) at 7.6 μm for Atmospheric Studies

    Science.gov (United States)

    Perrin, A.; Flaud, J. M.; Ridolfi, M.; Carlotti, M.

    2012-06-01

    Nitric acid (HNO_3) plays an important role as a reservoir molecule of the NO_x (nitrogen oxides) species in the stratosphere. The three strongest infrared bands of nitric acid are located at 11 μm (ν_5 and 2ν_9 bands), 7.6 μm (the ν_3 and ν_4 bands at 1326 and 1303 cm-1) and 5.8 μm (ν_2 band). Although two times weaker than those located at 7.6 and 5.8 μm, the 11 μm region is the only one which is used for nitric acid retrievals in the atmosphere by several satellite instruments like MIPAS (Michelson Interferometer for Passive Atmospheric Sounding on ENVISAT) or ACE-FTS (ACE Fourier transform spectrometer on SCISAT). This is because the available spectroscopic parameters for HNO_3 in the HITRAN and GEISA databases are of very good quality in this spectral region. Of the two remaining bands, the 7.6 μm one is only partly masked by water, and therefore can be used also for nitric acid retrievals in the upper stratosphere. Moreover, because of their large difference in band intensity, combining measurements at 11 μm and 7.6 μm could maximize informations on the vertical distribution of HNO_3 in the atmosphere. However at 7.6 μm the spectroscopic parameters available in the HITRAN and GEISA databases are are not so good. Indeed, these parameters originate from a list generated more than 20 years ago. The low quality of the list at 7.6 μm prevents HNO_3 retrievals and severely affects the retrievals of several species absorbing in the 7.5-7.7 μm region, like SO_2. This work is a new and more accurate investigation of the line positions and intensities for the ν_3 and ν_4 bands of nitric acid located at 1326.187 and 1303.074 cm-1). For this task, we used new infrared laboratory data combined with a new theoretical model. Examples showing substantial improvements will be given. [1] Rothman et al. J. Quant. Spectrosc. Radiat. Transf., 110, 533-572, 2009 [2] Jacquinet et al. J. Quant. Spectrosc. Radiat. Transf., 112, 2395-2445, 2011 [3] A. Perrin, O. Lado

  4. Kinetics of Acid-Catalyzed Dehydration of Cyclic Hemiacetals in Organic Aerosol Particles in Equilibrium with Nitric Acid Vapor.

    Science.gov (United States)

    Ranney, April P; Ziemann, Paul J

    2016-04-28

    Previous studies have shown that 1,4-hydroxycarbonyls, which are often major products of the atmospheric oxidation of hydrocarbons, can undergo acid-catalyzed cyclization and dehydration in aerosol particles to form highly reactive unsaturated dihydrofurans. In this study the kinetics of dehydration of cyclic hemiacetals, the rate-limiting step in this process, was investigated in a series of environmental chamber experiments in which secondary organic aerosol (SOA) containing cyclic hemiacetals was formed from the reaction of n-pentadecane with OH radicals in dry air in the presence of HNO3. A particle beam mass spectrometer was used to monitor the formation and dehydration of cyclic hemiacetals in real time, and SOA and HNO3 were quantified in filter samples by gravimetric analysis and ion chromatography. Measured dehydration rate constants increased linearly with increasing concentration of HNO3 in the gas phase and in SOA, corresponding to catalytic rate constants of 0.27 h(-1) ppmv(-1) and 7.0 h(-1) M(-1), respectively. The measured Henry's law constant for partitioning of HNO3 into SOA was 3.7 × 10(4) M atm(-1), ∼25% of the value for dissolution into water, and the acid dissociation constant was estimated to be water. The results indicate that HNO3 was only weakly dissociated in the SOA and that dehydration of cyclic hemiacetals was catalyzed by molecular HNO3 rather than by H(+). The Henry's law constant and kinetics relationships measured here can be used to improve mechanisms and models of SOA formation from the oxidation of hydrocarbons in dry air in the presence of NOx, which are conditions commonly used in laboratory studies. The fate of cyclic hemiacetals in the atmosphere, where the effects of higher relative humidity, organic/aqueous phase separation, and acid catalysis by molecular H2SO4 and/or H(+) are likely to be important, is discussed.

  5. A-train CALIOP and MLS observations of early winter antarctic polar stratospheric clouds and nitric acid in 2008

    Directory of Open Access Journals (Sweden)

    A. Lambert

    2011-10-01

    Full Text Available A-train Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP and Microwave Limb Sounder (MLS observations are used to investigate the development of polar stratospheric clouds (PSCs and the gas phase nitric acid distribution in the early 2008 Antarctic winter. Observational evidence of gravity-wave activity is provided by Atmospheric Infrared Sounder (AIRS radiances and infrared spectroscopic detection of nitric acid trihydrate (NAT in PSCs is obtained from the Michelson Interferometer for Passive Atmospheric Sounding (MIPAS. Goddard Earth Observing System Data Assimilation System (GEOS-5 DAS analyses are used to derive Lagrangian trajectories and to determine temperature-time histories of air parcels. We use CALIOP backscatter and depolarization measurements to classify PSCs and the MLS measurements to determine the corresponding gas phase HNO3 as a function of temperature. For liquid PSCs the uptake of HNO3 follows the theoretical equilibrium curve for supercooled ternary solutions (STS, but at temperatures about 1 K lower as determined from GEOS-5. In the presence of solid phase PSCs, above the ice frost-point, the HNO3 depletion occurs over a wider range of temperatures (+2 to −7 K distributed about the NAT equilibrium curve. Rapid gas phase HNO3 depletion is first seen by MLS from from 23–25 May 2008, consisting of a decrease in the volume mixing ratio (parts per billion by volume from 14 ppbv to 7 ppbv on the 46–32 hPa (hectopascal pressure levels and accompanied by a 2–3 ppbv increase by renitrification at the 68 hPa pressure level. Temperature-time histories of air parcels demonstrate that the depleted HNO3 region is more clearly correlated with prior low temperature exposure of a few kelvin above the frost-point than with either the region bounded by the NAT existence temperature threshold or the region of minimum temperatures. From the combined data we infer the

  6. A-train CALIOP and MLS observations of early winter Antarctic polar stratospheric clouds and nitric acid in 2008

    Directory of Open Access Journals (Sweden)

    A. Lambert

    2012-03-01

    Full Text Available A-train Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP and Microwave Limb Sounder (MLS observations are used to investigate the development of polar stratospheric clouds (PSCs and the gas-phase nitric acid distribution in the early 2008 Antarctic winter. Observational evidence of gravity-wave activity is provided by Atmospheric Infrared Sounder (AIRS radiances and infrared spectroscopic detection of nitric acid trihydrate (NAT in PSCs is obtained from the Michelson Interferometer for Passive Atmospheric Sounding (MIPAS. Goddard Earth Observing System Data Assimilation System (GEOS-5 DAS analyses are used to derive Lagrangian trajectories and to determine temperature-time histories of air parcels. We use CALIOP backscatter and depolarization measurements to classify PSCs and the MLS measurements to determine the corresponding gas-phase HNO3 as a function of temperature. For liquid PSCs the uptake of HNO3 follows the theoretical equilibrium curve for supercooled ternary solutions (STS, but at temperatures about 1 K lower as determined from GEOS-5. In the presence of solid phase PSCs, above the ice frost-point, the HNO3 depletion occurs over a wider range of temperatures (+2 to −7 K distributed about the NAT equilibrium curve. Rapid gas-phase HNO3 depletion is first seen by MLS from from 23–25 May 2008, consisting of a decrease in the volume mixing ratio from 14 ppbv (parts per billion by volume to 7 ppbv on the 46–32 hPa (hectopascal pressure levels and accompanied by a 2–3 ppbv increase by renitrification at the 68 hPa pressure level. The observed region of depleted HNO3 is substantially smaller than the region bounded by the NAT existence temperature threshold. Temperature-time histories of air parcels demonstrate that the depletion is more clearly correlated with prior exposure to temperatures a few kelvin above the frost-point. From the combined data we infer the presence

  7. Gibberellic acid alleviates cadmium toxicity by reducing nitric oxide accumulation and expression of IRT1 in Arabidopsis thaliana

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Xiao Fang [State Key Laboratory of Plant Physiology and Biochemistry, College of Life Sciences, Zhejiang University, Hangzhou 310058 (China); Jiang, Tao [Key Laboratory of Conservation Biology for Endangered Wildlife of the Ministry of Education, College of Life Sciences, Zhejiang University, Hangzhou 310058 (China); Wang, Zhi Wei [State Key Laboratory of Plant Physiology and Biochemistry, College of Life Sciences, Zhejiang University, Hangzhou 310058 (China); Lei, Gui Jie [Key Laboratory of Conservation Biology for Endangered Wildlife of the Ministry of Education, College of Life Sciences, Zhejiang University, Hangzhou 310058 (China); Shi, Yuan Zhi [The Key Laboratory of Tea Chemical Engineering, Ministry of Agriculture, Yunqi Road 1, Hangzhou 310008 (China); Li, Gui Xin, E-mail: guixinli@zju.edu.cn [College of Agronomy and Biotechnology, Zhejiang University, Hangzhou 310058 (China); Zheng, Shao Jian [State Key Laboratory of Plant Physiology and Biochemistry, College of Life Sciences, Zhejiang University, Hangzhou 310058 (China); Key Laboratory of Conservation Biology for Endangered Wildlife of the Ministry of Education, College of Life Sciences, Zhejiang University, Hangzhou 310058 (China)

    2012-11-15

    Highlights: Black-Right-Pointing-Pointer Cd reduces endogenous GA levels in Arabidopsis. Black-Right-Pointing-Pointer GA exogenous applied decreases Cd accumulation in plant. Black-Right-Pointing-Pointer GA suppresses the Cd-induced accumulation of NO. Black-Right-Pointing-Pointer Decreased NO level downregulates the expression of IRT1. Black-Right-Pointing-Pointer Suppressed IRT1 expression reduces Cd transport across plasma membrane. - Abstract: Gibberellic acid (GA) is involved in not only plant growth and development but also plant responses to abiotic stresses. Here it was found that treating the plants with GA concentrations from 0.1 to 5 {mu}M for 24 h had no obvious effect on root elongation in the absence of cadmium (Cd), whereas in the presence of Cd{sup 2+}, GA at 5 {mu}M improved root growth, reduced Cd content and lipid peroxidation in the roots, indicating that GA can partially alleviate Cd toxicity. Cd{sup 2+} increased nitric oxide (NO) accumulation in the roots, but GA remarkably reduced it, and suppressed the up-regulation of the expression of IRT1. In contrary, the beneficial effect of GA on alleviating Cd toxicity was not observed in an IRT1 knock-out mutant irt1, suggesting the involvement of IRT1 in Cd{sup 2+} absorption. Furthermore, the GA-induced reduction of NO and Cd content can also be partially reversed by the application of a NO donor (S-nitrosoglutathione [GSNO]). Taken all these together, the results showed that GA-alleviated Cd toxicity is mediated through the reduction of the Cd-dependent NO accumulation and expression of Cd{sup 2+} uptake related gene-IRT1 in Arabidopsis.

  8. Polymeric beads containing Cyanex 923 for actinide uptake from nitric acid medium: Studies with uranium and plutonium.

    Science.gov (United States)

    Gujar, R B; Lakshmi, D Shanthana; Figoli, A; Mohapatra, P K

    2013-08-30

    Conventional phase inversion technique has been successfully applied for the preparation of the solid phase extractant (SPE), Cyanex 923 loaded polymer beads. Two types of polymer beads prepared by blending Polyetherether ketone with card (PEEKWC)/DMF with 5% Cyanex 923 (SPE-I, av bead size: 900μm) and 10% Cyanex 923(SPE-II, av. bead size: 1100μm) were evaluated for the uptake of actinide ions. The polymer beads were characterized by various physical methods such as thermal analysis, surface morphology analysis by SEM, EDAX techniques, etc. The polymer beads were used for the experiments involving the uptake of both U(VI) and Pu(IV) at tracer scale and U(VI) at milli molar concentrations from nitric acid feeds. The actinide ion uptake studies involved kinetics of metal ion sorption, adsorption isotherms, and column studies. The metal sorption capacities for U(VI) at 3M HNO3 were found to be 38.8±1.9mg and 54.5±1.7mg per g of SPE-I and SPE-II, respectively. The sorption isotherm analysis with Langmuir, D-R and Freundlisch isotherms indicated chemisorption monolayer mechanism. Column studies were also carried out using 4.5mL bed volume columns containing about 0.4 and 0.45g of SPE-I and SPE-II, respectively. The breakthrough profiles were obtained for U(VI) and the elution profiles were obtained using 1M Na2CO3 as the eluent.

  9. Spatial and temporal distribution of ambient nitric acid and ammonia in the Athabasca Oil Sands Region, Alberta

    Directory of Open Access Journals (Sweden)

    Diane ALEXANDER

    2010-08-01

    Full Text Available Monthly average ambient concentrations of gaseous nitric acid (HNO3 and ammonia (NH3 were monitored at the Athabasca Oils Sands Region (AOSR, Alberta, Canada, between May 2005 and September 2008. Generally, concentrations of both pollutants were elevated and highly variable in space and time. The highest atmospheric concentrations occurred in the vicinity of the major mining and oil extraction activities of Fort Murray and Fort McKay. Maximum monthly average concentrations of HNO3 decreased from >6 μg m–3 2005 and 2006 to <4 μg m–3 in 2007 and 2008. While the HNO3 summer seasonal averages in 2005 and 2006 approached ~2 μg m–3 at some sites, in the subsequent summers and during winter seasons it rarely exceeded 1 μg m–3 and no clear differences between summer and winter occurred. Concentrations of NH3 were elevated during the entire study and frequently reached 6 μg m–3. Generally, NH3 stayed higher in summer than in winter; the summer seasonal averages often exceeded 4 μg m–3 while those for winter only on two occasions were above 3 μg m–3. In summer 2008, an expansion of the area with elevated NH3 levels was observed extending to remote locations. Ammonia is of a much higher concern from a perspective of possible biological effects, because of its potential for direct toxic effect on lichens and its contribution to the elevated N dry deposition with possible negative consequences for forests and other ecosystems.

  10. The partitioning of Nitric Acid between the gas phase and condensed phase of aqueous sulfate aerosols.

    Science.gov (United States)

    Mentel, T. F.; Folkers, M.; Sebald, H.; Wahner, A.

    2001-12-01

    The heterogeneous hydrolysis of N2O_5 on aqueous aerosol surfaces is an important source of atmospheric HNO3. We generated HNO3 by heterogeneous hydrolysis of N2O_5 on aqueous ammonium and sodium sulfate aerosols and studied its partitioning between the gas phase and the aerosol phase. The experiments were performed in the large aerosol chamber at the FZ-Jülich at several relative humidities. Gas phase processes and the composition of the aerosols were monitored on-line simultaneously by FTIR spectroscopy and by Steam Jet Aerosol Collection/Ion Chromatography. The aerosol size distributions in the range of 20 nm to 5 μ m were measured by differential electromobility classification and by aerodynamic particle sizing. In the presence of aqueous bisulfate and sulfate aerosols a fast heterogeneous formation HNO3 is observed. (The reaction probability of N2O_5 is about 0.02.) In the case of the acidic bisulfate aerosols the major fraction of heterogeneously formed HNO3 resides in the gas phase. For neutral sulfate aerosols a significant fraction of HNO3 is taken up by the condensed phase of the aerosols. This leads to a distinctive growth of the aerosol population during the heterogeneous hydrolysis of N2O_5, which is observable in the number size distribution as well as in IR extinction measurements. The observed partitioning of HNO3 between gas phase and aqueous aerosol phase can be quantitatively understood by a Pitzer based thermodynamic model for salt solutions of high ionic strength. The model calculations and low resolution FTIR spectroscopy demonstrate that protonation of sulfate to bisulfate is the driving force for the uptake of HNO3 in neutral sulfate aerosols.

  11. Effects of Acid Treatment and Enzymatic Treatment on the Content and Properties of Resistant Starch in Boiled Rice%酸或酶处理对米饭抗性淀粉含量和性质的影响

    Institute of Scientific and Technical Information of China (English)

    王增兴; 陈明芬; 卢训

    2011-01-01

    Resistant starch is difficult to digest due to its physical characteristics,which can play important roles in blood glucose regulation,body weight control,cancer prevention and other physiological activities.Resistant starch has been classified into four categories depending on resistance causes.Type III resistant starch(RSIII) is a retrograded and non-granular starch that can be generated by various types of processing.In this study,the formation of RSIII in boiled rice was explored based on acid treatment and pullulanase treatment.Both treatments could increase the content of resistant starch in boiled rice.Differential scanning calorimetry analysis revealed increased initial pasting temperature,phase transition peak temperature and phase transition enthalpy of starch in boiled rice due to the increased content of resistant starch.X-ray diffraction showed that crystal structure of resistant starch in boiled rice converted into Type V from Type A.Moreover,the resistant starch achieved by these treatments revealed excellent thermal stability.%抗性淀粉中第3型抗性淀粉属于回凝性淀粉,可经由各种加工处理提高其含量,以台农71号精白米为材料,研究开发一种直接提高米饭中第3型抗性淀粉含量的制程,直接在米饭内进行酸处理或酶处理,然后检测抗性淀粉含量的变化,并进行微差扫描热分析、X射线衍射以及热稳定性测定。结果显示:直接在米饭内进行酶处理之制程可以使米饭中抗性淀粉的含量由原来的0.4%提高至20%以上;微差扫描热分析结果显示加工后的米饭样品起始糊化温度(To)、相变高峰温度(Tp)和相变焓(ΔH)均高于未经处理米饭样品,显示淀粉结晶结构已经改变;X射线衍

  12. [Nitric oxide].

    Science.gov (United States)

    Rovira, I

    1995-01-01

    Nitric oxide was identified as the relaxing factor derived from the endothelium in 1987. Nitric oxide synthesis allows the vascular system to maintain a state of vasodilation, thereby regulating arterial pressure. Nitric oxide is also found in platelets, where it inhibits adhesion and aggregation; in the immune system, where it is responsible for the cytotoxic action of macrophages; and in the nervous system, where it acts as neurotransmitter. A deficit in endogenous synthesis of nitric oxide contributes to such conditions as essential arterial hypertension, pulmonary hypertension and heart disease. An excess of nitrous oxide induced by endotoxins and cytokinins, meanwhile, is believed to be responsible for hypotension in septic shock and for hyperdynamic circulatory state in cirrhosis of the liver. Nitric oxide has also been implicated in the rejection of transplanted organs and in cell damage after reperfusion. Inhaled nitrous oxide gas reduces pulmonary hypertension without triggering systemic hypotension in both experimental and clinical conditions. It also produces selective vasodilation when used to ventilate specific pulmonary areas, thereby improving the ventilation/perfusion ratio and, hence, oxygenation. Nitric oxide inhalation is effective in pulmonary hypertension-coincident with chronic obstructive lung disease, in persistent neonatal pulmonary hypertension and in pulmonary hypertension with congenital or acquired heart disease. Likewise, it reduces intrapulmonary shunt in acute respiratory failure and improves gas exchange. Under experimental conditions nitric oxide acts as a bronchodilator, although it seems to be less effective for this purpose in clinical use.(ABSTRACT TRUNCATED AT 250 WORDS)

  13. Influence of gas-particle partitioning on ammonia and nitric acid fluxes above a deciduous forest in the Midwestern USA

    Science.gov (United States)

    Hansen, K.; Sørensen, L. L.; Hornsby, K. E.; Boegh, E.; Pryor, S. C.

    2013-12-01

    Quantifying the atmosphere-biosphere exchange of reactive nitrogen gasses (including ammonia (NH3) and nitric acid (HNO3)) is crucial to assessing the impact of anthropogenic activities on natural and semi-natural ecosystems. However, measuring the deposition of reactive nitrogen is challenging due to bi-directionality of the flux, and the dynamics of the chemical gas/aerosol equilibrium of NH3 and HNO3 (or other atmospheric acids) with aerosol-phase ammonium (NH4+) and nitrate (NO3-). NH3 and HNO3 are both very reactive and typically exhibit higher deposition velocities than aerosol NH4+. Therefore, the phase partitioning between gas and aerosol phases can have a significant effect on local budgets and atmospheric transport distances (Nemitz et al., Atmos. Chem. Phys., 2004). In this study, fluxes of NH3, HNO3 and carbon dioxide (CO2) along with size-resolved N-aerosol concentrations are measured above the deciduous forest, Morgan Monroe State Forest (MMSF) in south-central Indiana (39°53'N, 86°25'W) during a field campaign. Two relaxed eddy accumulation (REA) systems are used to measure fluxes and concentrations of NH3 and HNO3 at 44 m. The NH3 REA system operates based on wet effluent diffusion denuders with detection by florescence and half-hourly flux measurements are calculated. HNO3 REA system is based on gas capture on sodium chloride (NaCl) coated denuders with subsequent analysis by ion-chromatography, and the resulting fluxes have a resolution of 3-4 hours. CO2 fluxes are measured by eddy covariance using a closed-path Licor LI-7500, while two MSP MOUDI-110 impactors are used to measure the 24-hourly average inorganic and 48 hourly averaged organic ion concentrations in 11 size bins, respectively, just above the canopy level (28 m). The results of this field campaign are used to quantify the fluxes of NH3, HNO3, CO2 to/from the forest during the transition towards senescence, and to investigate process-level controls (e.g. the role of phase

  14. Improvement of oxygen-containing functional groups on olive stones activated carbon by ozone and nitric acid for heavy metals removal from aqueous phase.

    Science.gov (United States)

    Bohli, Thouraya; Ouederni, Abdelmottaleb

    2016-08-01

    Recently, modification of surface structure of activated carbons in order to improve their adsorption performance toward especial pollutants has gained great interest. Oxygen-containing functional groups have been devoted as the main responsible for heavy metal binding on the activated carbon surface; their introduction or enhancement needs specific modification and impregnation methods. In the present work, olive stones activated carbon (COSAC) undergoes surface modifications in gaseous phase using ozone (O3) and in liquid phase using nitric acid (HNO3). The activated carbon samples were characterized using N2 adsorption-desorption isotherm, SEM, pHpzc, FTIR, and Boehm titration. The activated carbon parent (COSAC) has a high surface area of 1194 m(2)/g and shows a predominantly microporous structure. Oxidation treatments with nitric acid and ozone show a decrease in both specific surface area and micropore volumes, whereas these acidic treatments have led to a fixation of high amount of surface oxygen functional groups, thus making the carbon surface more hydrophilic. Activated carbon samples were used as an adsorbent matrix for the removal of Co(II), Ni(II), and Cu(II) heavy metal ions from aqueous solutions. Adsorption isotherms were obtained at 30 °C, and the data are well fitted to the Redlich-Peterson and Langmuir equation. Results show that oxidized COSACs, especially COSAC(HNO3), are capable to remove more Co(II), Cu(II), and Ni(II) from aqueous solution. Nitric acid-oxidized olive stones activated carbon was tested in its ability to remove metal ions from binary systems and results show an important maximum adsorbed amount as compared to single systems.

  15. Hydrogen Peroxide and Nitric Oxide are Involved in Salicylic Acid-Induced Salvianolic Acid B Production in Salvia miltiorrhiza Cell Cultures

    Directory of Open Access Journals (Sweden)

    Hongbo Guo

    2014-05-01

    Full Text Available Hydrogen peroxide (H2O2 and nitric oxide (NO are key signaling molecules in cells whose levels are increased in response to various stimuli and are involved in plant secondary metabolite synthesis. In this paper, the roles of H2O2 and NO on salvianolic acid B (Sal B production in salicylic acid (SA-induced Salvia miltiorrhiza cell cultures were investigated. The results showed that H2O2 could be significantly elicited by SA, even though IMD (an inhibitor of NADPH oxidase or DMTU (a quencher of H2O2 were employed to inhibit or quench intracellular H2O2. These elicited H2O2 levels significantly increased NO production by 1.6- and 1.46 fold in IMD+SA and DMTU+SA treatments, respectively, and induced 4.58- and 4.85-fold Sal B accumulation, respectively. NO was also markedly elicited by SA, in which L-NNA (an inhibitor of NO synthase and cPTIO (a quencher of NO were used to inhibit or quench NO within cells, and the induced NO could significantly enhance H2O2 production by 1.92- and 1.37-fold in L-NNA+SA and cPTIO+SA treatments, respectively, and 3.27- and 1.50-fold for Sal B accumulation, respectively. These results indicate that elicitation of SA for either H2O2 or NO was independent, and the elicited H2O2 or NO could act independently or synergistically to induce Sal B accumulation in SA-elicited cells.

  16. Nitric oxide-releasing poly(lactic-co-glycolic acid-polyethylenimine nanoparticles for prolonged nitric oxide release, antibacterial efficacy, and in vivo wound healing activity

    Directory of Open Access Journals (Sweden)

    Nurhasni H

    2015-04-01

    Full Text Available Hasan Nurhasni,1 Jiafu Cao,1 Moonjeong Choi,1 Il Kim,2 Bok Luel Lee,1 Yunjin Jung,1 Jin-Wook Yoo11College of Pharmacy, Pusan National University, Busan, South Korea; 2Department of Polymer Science and Engineering, Pusan National University, Busan, South KoreaAbstract: Nitric oxide (NO-releasing nanoparticles (NPs have emerged as a wound healing enhancer and a novel antibacterial agent that can circumvent antibiotic resistance. However, the NO release from NPs over extended periods of time is still inadequate for clinical application. In this study, we developed NO-releasing poly(lactic-co-glycolic acid-polyethylenimine (PEI NPs (NO/PPNPs composed of poly(lactic-co-glycolic acid and PEI/diazeniumdiolate (PEI/NONOate for prolonged NO release, antibacterial efficacy, and wound healing activity. Successful preparation of PEI/NONOate was confirmed by proton nuclear magnetic resonance, Fourier transform infrared spectroscopy, and ultraviolet/visible spectrophotometry. NO/PPNPs were characterized by particle size, surface charge, and NO loading. The NO/PPNPs showed a prolonged NO release profile over 6 days without any burst release. The NO/PPNPs exhibited potent bactericidal efficacy against methicillin-resistant Staphylococcus aureus (MRSA and Pseudomonas aeruginosa concentration-dependently and showed the ability to bind on the surface of the bacteria. We also found that the NO released from the NO/PPNPs mediates bactericidal efficacy and is not toxic to healthy fibroblast cells. Furthermore, NO/PPNPs accelerated wound healing and epithelialization in a mouse model of a MRSA-infected wound. Therefore, our results suggest that the NO/PPNPs presented in this study could be a suitable approach for treating wounds and various skin infections.Keywords: nitric oxide-releasing nanoparticles, PLGA, PEI, antimicrobial, wound healing

  17. Violent explosion after inadvertent mixing of nitric acid and isopropanol – Review 15 years later finds basic accident data corrupted, no evidence of broad learning

    DEFF Research Database (Denmark)

    Hedlund, Frank Huess; Folmer Nielsen, Merete; Hagen Mikkelsen, Sonja

    2014-01-01

    steel tank disintegrated with such force that fragments lodged in walls of concrete. The explosion ravaged the cellar, destroyed equipment, blew out a masonry wall and released large amounts of nitrous oxide fumes. Likely, 62% nitric acid (CAS 7697-37-2) and isopropanol (2-propanol, CAS 67-63-0) reacted...... the brewery to court for negligence, they did not report or investigate the accident, or attempt to disseminate information available to them. Today, the general literature is silent on the explosion hazards of mixing the two chemicals. The paper argues that without institutional support, learning...

  18. Formation of nitric oxide, ethyl nitrite and an oxathiolone derivative of caffeic acid in a mixture of saliva and white wine.

    Science.gov (United States)

    Takahama, Umeo; Tanaka, Mariko; Hirota, Sachiko

    2010-03-01

    Reactions of salivary nitrite with components of wine were studied using an acidic mixture of saliva and wine. The formation of nitric oxide (NO) in the stomach after drinking wine was observed. The formation of NO was also observed in the mixture (pH 3.6) of saliva and wine, which was prepared by washing the oral cavity with wine. A part of the NO formation in the stomach and the oral cavity was due to the reduction of salivary nitrite by caffeic and ferulic acids present in wine. Ethyl nitrite produced by the reaction of salivary nitrite and ethyl alcohol in wine also contributed to the formation of NO. In addition to the above reactions, caffeic acid in wine could be transformed to the oxathiolone derivative, which might have pharmacological functions. The results obtained in this study may help in understanding the effects of drinking wine on human health.

  19. Fabrication process for sintered mixed oxides soluble in nitric acid from nitrate solutions. [nuclear fuels]. Procede d'obtention d'oxydes mixtes frittes solubles dans l'acide nitrique a partir de solutions de nitrates

    Energy Technology Data Exchange (ETDEWEB)

    Bachelard, R.; Germanaz, P.

    1987-10-02

    Mixed oxide nuclear fuels are obtained by mixing the nitrate solutions, concentration, heat treatment for an intermediary mixed oxide containing U(VI) and Pu(IV or VI), calcination to obtain U/sub 3/O/sub 8/, reduction in U(IV) and Pu(IV), pelletizing, sintering and machining. Less wastes are produced and the fuel pellets are soluble in nitric acid.

  20. 加快产业结构调整与建设大型硝酸装置的思考%Accelerate Industrial Restructure and Build Large Nitric Acid Plants

    Institute of Scientific and Technical Information of China (English)

    唐文骞; 杨同莲

    2012-01-01

    引入原料与资源量、能源量的概念,分析了各种硝酸生产方法中的吨酸比氨耗值和比能源值.通过产业结构调整的分析可知,双加压法硝酸具有无可争议的优势,该法应成为我国硝酸工业发展的主流工艺.同时指出建设大型或特大型双加压法硝酸装置在我国已具备设计、制造、运行的条件和经验,并将取得十分可观的经济效益.%By introducing the concept of feedstock, amount of resource and energy, the specific ammonia consumption per ton of nitric acid and the specific energy consumption per ton of nitric acid through different nitric acid production processes were analyzed. The result of specific energy consumption comparisons shows that the dual pressure process has the indisputable advantage against other processes. It should become the mainstream process in the development of nitric acid industry in China. The paper also pointed out that China has already the ability and experience in engineering design, manufacture and operation of large and super-large nitric acid plants adopting the dual pressure process and has obtained considerable economic benefits.

  1. Pimaradienoic Acid Inhibits Carrageenan-Induced Inflammatory Leukocyte Recruitment and Edema in Mice: Inhibition of Oxidative Stress, Nitric Oxide and Cytokine Production.

    Directory of Open Access Journals (Sweden)

    Sandra S Mizokami

    Full Text Available Pimaradienoic acid (PA; ent-pimara-8(14,15-dien-19-oic acid is a pimarane diterpene found in plants such as Vigueira arenaria Baker (Asteraceae in the Brazilian savannas. Although there is evidence on the analgesic and in vitro inhibition of inflammatory signaling pathways, and paw edema by PA, its anti-inflammatory effect deserves further investigation. Thus, the objective of present study was to investigate the anti-inflammatory effect of PA in carrageenan-induced peritoneal and paw inflammation in mice. Firstly, we assessed the effect of PA in carrageenan-induced leukocyte recruitment in the peritoneal cavity and paw edema and myeloperoxidase activity. Next, we investigated the mechanisms involved in the anti-inflammatory effect of PA. The effect of PA on carrageenan-induced oxidative stress in the paw skin and peritoneal cavity was assessed. We also tested the effect of PA on nitric oxide, superoxide anion, and inflammatory cytokine production in the peritoneal cavity. PA inhibited carrageenan-induced recruitment of total leukocytes and neutrophils to the peritoneal cavity in a dose-dependent manner. PA also inhibited carrageenan-induced paw edema and myeloperoxidase activity in the paw skin. The anti-inflammatory mechanism of PA depended on maintaining paw skin antioxidant activity as observed by the levels of reduced glutathione, ability to scavenge the ABTS cation and reduce iron as well as by the inhibition of superoxide anion and nitric oxide production in the peritoneal cavity. Furthermore, PA inhibited carrageenan-induced peritoneal production of inflammatory cytokines TNF-α and IL-1β. PA presents prominent anti-inflammatory effect in carrageenan-induced inflammation by reducing oxidative stress, nitric oxide, and cytokine production. Therefore, it seems to be a promising anti-inflammatory molecule that merits further investigation.

  2. Film boiling of mercury droplets

    Science.gov (United States)

    Baumeister, K. J.; Schoessow, G. J.; Chmielewski, C. E.

    1975-01-01

    Vaporization times of mercury droplets in Leidenfrost film boiling on a flat horizontal plate are measured in an air atmosphere. Extreme care was used to prevent large amplitude droplet vibrations and surface wetting; therefore, these data can be compared to film boiling theory. For these data, diffusion from the upper surface of the drop is a dominant mode of mass transfer from the drop. A closed-form analytical film boiling theory is developed to account for the diffusive evaporation. Reasonable agreement between data and theory is seen.

  3. Effects of abscisic acid and nitric oxide on trap formation and trapping of nematodes by the fungus Drechslerella stenobrocha AS6.1.

    Science.gov (United States)

    Xu, Ling-Ling; Lai, Yi-Ling; Wang, Lin; Liu, Xing-Zhong

    2011-02-01

    The in vitro effects of abscisic acid (ABA) and nitric oxide (NO) on the nematode-trapping fungus Drechslerella stenobrocha AS6.1 were examined. The average number of traps (constricting rings) per colony and the percentage of nematodes (Caenorhabditis elegans) trapped were greatly increased by addition of ABA but greatly suppressed by addition of sodium nitroprusside (SNP, an NO donor) to corn meal agar. The suppressive effect of SNP was not negated by addition of an NO synthase competitive inhibitor (l-naphthylacetic acid, L-NNA) or an NO-specific scavenger [2-(4-carboxyphenyl)-4,4, 5,5-tetramethylimidazoline-1-oxyl-3-oxide, cPTIO]. When added without SNP, however, L-NNA and cPTIO caused moderate increases in trap number and trapping. The results indicate that the trap formation and nematode-trapping ability of D. stenobrocha were enhanced by ABA but decreased by exogenous NO.

  4. Enhanced heat transfer in confined pool boiling

    NARCIS (Netherlands)

    Rops, C.M.; Lindken, R.; Velthuis, J.F.M.; Westerweel, J.

    2009-01-01

    We report the results of an experimental investigation of the heat transfer during nucleate boiling on a spatially confined boiling surface. The heat flux as a function of the boiling surface temperature was measured in pool boiling pots with diameters ranging from 15 mm down to 4.5 mm. It was found

  5. High flux film and transition boiling

    Energy Technology Data Exchange (ETDEWEB)

    Witte, L.C.

    1990-01-01

    This report is a bench-scale experiment on transition boiling. The author gives a detailed description on experimental apparatus and conditions. The visual observed boiling phenomena; nucleate boiling and film boiling, and the effect of heat transfer are also elucidated. 10 refs., 11 figs., 1 tab.

  6. Film boiling on vertical surfaces.

    Science.gov (United States)

    Suryanarayana, N. V.; Merte, H., Jr.

    1972-01-01

    Film boiling of a saturated liquid on a vertical surface is analyzed to determine the local heat-transfer rates as a function of height and heater-surface superheat. Experiments show that the laminar-flow model is inadequate. A turbulent-vapor-flow model is used, and the influence of the interfacial oscillations is incorporated on a semiempirical basis. Measurements of local film boiling were obtained with a transient technique using saturated liquid nitrogen.

  7. Recovery of nitric acid and hydrofluoric acid from passivation solution of steels by diffusion dialysis%扩散渗析法回收不锈钢钝化液中HNO3和HF

    Institute of Scientific and Technical Information of China (English)

    王昆; 刘飞; 邢卫红

    2012-01-01

    Recovery of nitric acid and hydrofluoric acid produced in passivation process of steels by diffusion dialysis was studied. The recovery rates of one-component nitric acid and hydrofluoric acid were investigated. Effects of flow rate, temperature and concentration of iron ion on mixed acid solution diffusion dialysis were analyzed. The results showed that it was an effective way to separate mixed acid solution by diffusion dialysis. The recovery rate decreased with the increase of the flow rate. Increasing the temperature was beneficial to the acid diffusion through the membrane. Under the operating condition of flow rate of 170 mL/h at normal temperature, the retention rate of iron ions was more than 95% ,the recovery rate of total acid was more than 85% with nitric acid 90% and hydrofluoric acid 40%.%采用扩散渗析法回收不锈钢钝化废液中的HNO3和HF,考察单组分酸、混合酸的回收率和废酸流量、温度、金属离子浓度等因素对扩散渗析过程的影响.结果表明:扩散渗析过程中HNO3回收率大于HF ;酸回收率随着废酸流量增大而减小 ;温度升高有利于酸扩散透过膜 ;Fe3+浓度对截留率影响不大.对于不锈钢钝化废酸液体系,扩散渗析对于H+和Fe3+具有良好的分离效果,常温下,废酸流量为170 mL/h时,总酸回收率为85%,其中HNO3回收率为90%,HF回收率为40%,Fe3+的截留率达到95%以上.

  8. Adsorption of sulfur dioxide by active carbon treated by nitric acid: I. Effect of the treatment on adsorption of SO{sub 2} and extractability of the acid formed

    Energy Technology Data Exchange (ETDEWEB)

    Lisovskii, A.; Semiat, R.; Aharoni, C. [Technion-Israle Institute of Technology, Haifa (Israel). Chemical Engineering Dept.

    1997-12-31

    Activated carbon is used as an adsorbent in flue gas cleaning. The process of adsorptive-catalytic cleaning of gas from sulfur dioxide using active carbon, treated by concentrated nitric acid, was studied. After oxidative treatment the acidity of the carbon increases and the basicity decreases. This results in an increase of the SO{sub 2} adsorption and its oxidation to SO{sub 3}, and in weaker retention of the sulfuric acid formed. This facilitates the removal of H{sub 2}SO{sub 4} by washing of the carbon and allows to obtain a more concentrated acid. The efficiency of the treated carbon is also higher in the process of SO{sub 2} removal from a gas similar in composition to stack gases. 13 refs., 1 fig., 7 tabs.

  9. Enrichment of nitrogen-15 by nitrox system. Part 1: countercorrent column of aqueous nitric acid and nitrogen oxides in gaseous phase; Enriquecimento de nitrogenio-15 pelo sistema Nitrox. Parte 1: coluna de contracorrente entre solucao de acido nitrico e oxidos de nitrogenio na fase gasosa

    Energy Technology Data Exchange (ETDEWEB)

    Ducatti, Carlos [UNESP, Botucatu, SP (Brazil). Inst. de Biociencias. Dept. de Fisica e Biofisica; Bonassi, Jose A.; Matsui, Eichii [Centro de Energia Nuclear na Agricultura (CENA), Piracicaba, SP (Brazil)

    1997-12-01

    In this paper described the operational mode of countercurrent column of aqueous nitric acid and nitrogen oxides (Nitrox System) for the production of nitric acid in the concentration of 5% atoms of {sup 15} N in laboratory. (author). 8 refs., 2 tabs., 1 fig.

  10. Americium(III) oxidation by copper(III) periodate in nitric acid solution as compared with the action of Bi(V) compounds of sodium, lithium, and potassium

    Energy Technology Data Exchange (ETDEWEB)

    Sinkov, Sergey I.; Lumetta, Gregg J. [Pacific Northwest National Laboratory, Radiochemical Processing Lab., Richland, WA (United States)

    2015-07-01

    The oxidative action of a Cu(III) periodate compound toward Am(III) in nitric acid was studied. The extent of oxidation of Am(III) to Am(VI) was investigated using a constant initial Cu(III)-to-Am(III) molar ratio of 10:1 and varying nitric acid concentrations from 0.25 to 3.5 mol/L. From 0.25 to 3 mol/L HNO3, more than 98% of the Am(III) was oxidized to Am(VI); however, at 3.5 mol/L HNO{sub 3}, the conversion to Am(VI) was only 80%. Increasing the Cu(III)-to-Am(III) molar ratio to 20:1 in 3.5 mol/L HNO{sub 3} resulted in 98% conversion to Am(VI). For comparison, oxidation of Am(III) with NaBiO{sub 3} was studied at 3.5 mol/L HNO{sub 3} and the same stoichiometric excess of Bi(V) oxidant over Am(III) (stoichiometric ratio of 3.33:1). With NaBiO{sub 3}, the extent of Am(III) conversion to Am(VI) was only 19%, while with the Cu(III) compound this value was found to be about 4 times higher under otherwise identical conditions. Similar results were obtained with other Bi(V) salts. These results show that the Cu(III) periodate compound is a superior oxidant to NaBiO{sub 3}, yielding rapid conversion to Am(VI) in a homogeneous acidic solution, and is, therefore, an excellent candidate for further development of Am separation systems.

  11. Hydroxycarboxylic acids and salts

    Energy Technology Data Exchange (ETDEWEB)

    Kiely, Donald E; Hash, Kirk R; Kramer-Presta, Kylie; Smith, Tyler N

    2015-02-24

    Compositions which inhibit corrosion and alter the physical properties of concrete (admixtures) are prepared from salt mixtures of hydroxycarboxylic acids, carboxylic acids, and nitric acid. The salt mixtures are prepared by neutralizing acid product mixtures from the oxidation of polyols using nitric acid and oxygen as the oxidizing agents. Nitric acid is removed from the hydroxycarboxylic acids by evaporation and diffusion dialysis.

  12. A theoretical study of nitric oxide adsorption and dissociation on copper-exchanged zeolites SSZ-13 and SAPO-34: the impact of framework acid-base properties.

    Science.gov (United States)

    Uzunova, Ellie L; Mikosch, Hans

    2016-04-28

    The adsorption of nitric oxide as dinitrosyls and the deNOx proton-mediated reaction mechanism are assessed using electronic structure methods and transition state theory. Dinitrosyls bind to copper cations either via a N-atom or via an O-atom, with N-binding being more stable. In their ground states, dinitrosyls reach a planar configuration with the metal cation. The two nitric oxide molecules are kept together in O-bonded dinitrosyls by the N-N bond and the adsorption complex obtains a cyclic planar structure, while N-bonded dinitrosyls have out-of-plane conformations with low energy barriers. An asymmetric structure ZCu(ON)(NO) with one N-bonded nitrosyl and the other O-bonded is of the lowest stability. The cyclic hyponitrite ZCu(ON)2 adsorption complex undergoes O-N bond breaking upon protonation of one oxygen atom and this lowers the energy barrier of the first reaction step of nitric oxide dissociation to yield N2O and a hydroxylated copper site ZCu(OH) by 45 kJ mol(-1) for Cu-SAPO-34 and by 46 kJ mol(-1) for Cu-SSZ-13. The more stable N-bonded dinitrosyl ZCu(NO)2 provides less favorable reaction which passes through the asymmetric ZCu(ON)(NO) intermediate structure. Brønsted acid sites facilitate the reversal of one nitrosyl group. The role of proton transfer from a Brønsted acid site to dinitrosyls is not limited to the initial step of facilitating the N-O bond cleavage, but it also contributes to the stabilization of intermediate oxygen species formed at the copper site as hydroxide ZCu(OH) and hydroperoxide, ZCuOOH. Without protonation, the unstable ZCuO intermediate causes structural deformation with strongly lengthened T-O bonds in the framework. The rate determining step is N2O decomposition to N2 and O2, whether starting with a ZCu(NO)2 or a ZCu(ON)2 adsorption complex, and Cu-SSZ-13 has a clear advantage with an energy barrier of 195 kJ mol(-1)vs. 265 kJ mol(-1) for Cu-SAPO-34. In the final step the Brønsted acid site is restored by proton

  13. Insights into the mechanism of extraction of uranium (VI) from nitric acid solution into an ionic liquid by using tri-n-butyl phosphate.

    Science.gov (United States)

    Gaillard, Dr Clotilde; Boltoeva, Maria; Billard, Isabelle; Georg, Sylvia; Mazan, Valérie; Ouadi, Ali; Ternova, Dariia; Hennig, Christoph

    2015-08-24

    We present new results on the liquid-liquid extraction of uranium (VI) from a nitric acid aqueous phase into a tri-n-butyl phosphate/1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (TBP/[C4 mim][Tf2 N]) phase. The individual solubilities of the ionic-liquid ions in the upper part of the biphasic system are measured over the whole acidic range and as a function of the TBP concentration. New insights into the extraction mechanism are obtained through the in situ characterization of the extracted uranyl complexes by coupling UV/Vis and extended X-ray absorption fine structure (EXAFS) spectroscopy. We propose a chemical model to explain uranium (VI) extraction that describes the data through a fit of the uranyl distribution ratio DU . In this model, at low acid concentrations uranium (VI) is extracted as the cationic complex [UO2 (TBP)2 ](2+) , by an exchange with one proton and one C4 mim(+) . At high acid concentrations, the extraction proceeds through a cationic exchange between [UO2 (NO3 )(HNO3 )(TBP)2 ](+) and one C4 mim(+) . As a consequence of this mechanism, the variation of DU as a function of TBP concentration depends on the C4 mim(+) concentration in the aqueous phase. This explains why noninteger values are often derived by analysis of DU versus [TBP] plots to determine the number of TBP molecules involved in the extraction of uranyl in an ionic-liquid phase.

  14. Nitric Acid Particles in Cold Thick Ice Clouds Observed at Global Scale: Link with Lightning, Temperature, and Upper Tropospheric Water Vapor

    Science.gov (United States)

    Chepfer, H.; Minnis, P.; Dubuisson, P.; Chiriaco, M.; Sun-Mack, S.; Riviere, E. D.

    2007-01-01

    Signatures of nitric acid particles (NAP) in cold thick ice clouds have been derived from satellite observations. Most NAP are detected in the Tropics (9 to 20% of clouds with T less than 202.5 K). Higher occurrences were found in the rare mid-latitudes very cold clouds. NAP occurrence increases as cloud temperature decreases and NAP are more numerous in January than July. Comparisons of NAP and lightning distributions show that lightning is the main source of the NOx, which forms NAP in cold clouds. Qualitative comparisons of NAP with upper tropospheric humidity distributions suggest that NAP play a role in the dehydration of the upper troposphere when the tropopause is colder than 195K.

  15. REACT-Mod: a mathematical model for transient calculation of chemical reactions with U-Pu-Np-Tc in the aqueous nitric acid solution

    Energy Technology Data Exchange (ETDEWEB)

    Tachimori, Shoichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kitamura, Tatsuaki

    1996-10-01

    A computer code REACT-Mod which simulates various chemical reactions in an aqueous nitric acid solution involving uranium, plutonium, neptunium, technetium etc. e.g., redox, radiolytic and disproportionation reactions of 68, was developed based on the kinetics model. The numerical solution method adopted in the code are two, a kinetics model totally based on the rate law of which differential equations are solved by the modified Porsing method, and a two-step model based on both the rate law and equilibrium law. Only the former treats 27 radiolytic reactions. The latter is beneficially used to have a quick and approximate result by economical computation. The present report aims not only to explain the concept, chemical reactions treated and characteristics of the model but also to provide details of the program for users of the REACT-Mod code. (author)

  16. Determination of plutonium in nitric acid solutions using energy dispersive L X-ray fluorescence with a low power X-ray generator

    Energy Technology Data Exchange (ETDEWEB)

    Py, J. [Laboratoire Chrono-Environnement, UMR CNRS 6249, Université de Franche-Comté, 16 route de Gray, F-25030 Besançon (France); Commissariat à l’Énergie Atomique, Centre de Valduc, F-21120 Is-sur-Tille (France); Groetz, J.-E., E-mail: jegroetz@univ-fcomte.fr [Laboratoire Chrono-Environnement, UMR CNRS 6249, Université de Franche-Comté, 16 route de Gray, F-25030 Besançon (France); Hubinois, J.-C.; Cardona, D. [Commissariat à l’Énergie Atomique, Centre de Valduc, F-21120 Is-sur-Tille (France)

    2015-04-21

    This work presents the development of an in-line energy dispersive L X-ray fluorescence spectrometer set-up, with a low power X-ray generator and a secondary target, for the determination of plutonium concentration in nitric acid solutions. The intensity of the L X-rays from the internal conversion and gamma rays emitted by the daughter nuclei from plutonium is minimized and corrected, in order to eliminate the interferences with the L X-ray fluorescence spectrum. The matrix effects are then corrected by the Compton peak method. A calibration plot for plutonium solutions within the range 0.1–20 g L{sup −1} is given.

  17. Synergistic extraction of U(VI) and Th(IV) from nitric acid media withHBMPPT and TBP in toluene

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The synergistic extraction of U(VI) and Th(IV) from nitric acid solutionby HBMPPT (4-benzoyl-2,4-dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione) andTBP (tributylphosphate ) in toluene was studied. The extraction abilityof HBMPPT for U(VI) and Th(IV) was not so high, but when a little TBP was added in, theability to extract U(VI) and Th(IV) was improved. The extracted complexes may be presented as UO2NO3.BMPPT.TBP and UO2(BMPPT)2 .TBP for U(VI), and Th(NO3)3.BMPPT.TBP andTh(NO3)2 (BMPPT)2.TBP for Th(IV),respectively, in the synergisticextraction system. The synergistic effect of HBMPPT and TBP makes the separationcoefficient of U(VI) /Th(IV) or U(VI)/Eu(III) reach a high value.

  18. The use of Liquid Smoke as A Substitute for Nitric Acid for Extraction of Amorphous silica from Rice husk through Sol-Gel Route

    Directory of Open Access Journals (Sweden)

    Wasinton Simanjuntak

    2016-08-01

    Full Text Available This study assessed the potential of liquid smoke as substitute for nitric acid for production of rice husk silica using sol-gel method. The efficacy of liquid smoke was compared to that of 10% HNO3 solution in terms of the volume required and the mass of silica obtained. Further evaluation was made by comparing the characteristics of the silica as revealed by several characterization techniques include Fourier infrared spectroscopy, x-ray diffraction, scanning electron microscopy, and particle size analysis. No significant difference between the volume of the liquid smoke and the HNO3 solution required, as well as between the mass of silica obtained. Both samples display practically similar functionality and structure. The most interesting finding is that the silica obtained using liquid smoke exhibits more homogeneous surface morphology and narrower particle size distribution. Considering its environmentally friendly nature, it was concluded that liquid smoke is more advantageous than HNO3 solution.

  19. Microstructures of Al7.5Cr22.5Fe35Mn20Ni15 High-Entropy Alloy and Its Polarization Behaviors in Sulfuric Acid, Nitric Acid and Hydrochloric Acid Solutions

    Directory of Open Access Journals (Sweden)

    Chun-Huei Tsau

    2016-08-01

    Full Text Available This paper investigates the microstructures and the polarization behaviors of Al7.5Cr22.5Fe35Mn20Ni15 high-entropy alloy in 1M (1 mol/L deaerated sulfuric acid (H2SO4, nitric acid (HNO3, and hydrochloric acid (HCl solutions at temperatures of 30–60 °C. The three phases of the Al7.5Cr22.5Fe35Mn20Ni15 high-entropy alloy are body-centered cubic (BCC dendrites, face-centered cubic (FCC interdendrites, and ordered BCC precipitates uniformly dispersed in the BCC dendrites. The different phases were corroded in different acidic solutions. The passivation regions of the Al7.5Cr22.5Fe35Mn20Ni15 alloy are divided into three and two sub-regions in the solutions of H2SO4 and HNO3 at 30–60 °C, respectively. The passivation region of the Al7.5Cr22.5Fe35Mn20Ni15 alloy is also divided into two sub-domains in 1M deaerated HCl solution at 30 °C. The Al7.5Cr22.5Fe35Mn20Ni15 alloy has almost equal corrosion resistance in comparison with 304 stainless steel (304SS in both the 1M H2SO4 and 1M HCl solutions. The polarization behaviors indicated that the Al7.5Cr22.5Fe35Mn20Ni15 alloy possessed much better corrosion resistance than 304SS in 1M HNO3 solution. However, in 1M NaCl solution, the corrosion resistance of the Al7.5Cr22.5Fe35Mn20Ni15 alloy was less than 304SS.

  20. Chlorogenic acid protection of neuronal nitric oxide synthase-positive neurons in the hippocampus of mice with impaired learning and memory

    Institute of Scientific and Technical Information of China (English)

    Qiuyun Tu; Xiangqi Tang; Zhiping Hu

    2008-01-01

    BACKGROUND: Clinical practice and modern pharmacology have confirmed that ehlorogenic acid can ameliorate learning and memory impairments. OBJECTIVE: To observe the effects of chlorogenic acid on neuronal nitric oxide synthase (nNOS)-positive neurons in the mouse hippocampus, and to investigate the mechanisms underlying the beneficial effects of chlorogenic acid on learning and memory. DESIGN, TIME AND SETTING: The present randomized, controlled, neural cell morphological observation was performed at the Institute of Neurobiology, Central South University between January and May 2005.MATERIALS: Forty-eight female, healthy, adult, Kunming mice were included in this study. Learning and memory impairment was induced with an injection of 0.5 μL kainic acid (0.4 mg/mL) into the hippocampus.METHODS: The mice were randomized into three groups (n = 16): model, control, and chlorogenic acid-treated. At 2 days following learning and memory impairment induction, intragastric administration of physiological saline or chlorogenic acid was performed in the model and chlorogenic acid-treated groups, respectively. The control mice were administered 0.5 μ L physiological saline into the hippocampus, and 2 days later, they received an intragastric administration of physiological saline. Each mouse received two intragastric administrations (1 mL solution once) per day, for a total of 35 days. MAIN OUTCOME MEASURES: Detection of changes in hippocampal and cerebral cortical nNOS neurons by immunohistochemistry; determination of spatial learning and memory utilizing the Y-maze device.RESULTS: At day 7 and 35 after intervention, there was no significant difference in the number of nNOS-positive neurons in the cerebral cortex between the model, chlorogenic acid, and control groups (P > 0.05). Compared with the control group, the number of nNOS-positive neurons in the hippocampal CA1-4 region was significantly less in the model group (P 0.05). At day 7 following intervention, the number

  1. In-air PIXE for analyzing heavy metals in water boiled in pans

    Science.gov (United States)

    Tomita, M.; Haruyama, Y.; Saito, M.

    1993-04-01

    The release rates of heavy metals from pans were measured for boiling water as well as for an acidic solution prior to an investigation on the release or sorption of trace elements due to cooking of food by boiling. The boiled samples were condensed and analyzed by means of in-air PIXE. The release of heavy metals was measured for five kinds of pans. For all pans the release rates were considerably more increased by boiling of a 5% solution of acetic acid. Furthermore it was found that by using the alumina coated aluminum pan (alumina pan) the respective release rates of Fe, Cu and Zn were all less than 50 μg per 100 cm 2 of the pan surface dipped in the solution, and that monitoring of the contents of aluminum in the boiled solution enabled the estimation of the contribution of metal elements from the pan wall.

  2. Polyphenol fraction of extra virgin olive oil protects against endothelial dysfunction induced by high glucose and free fatty acids through modulation of nitric oxide and endothelin-1

    Directory of Open Access Journals (Sweden)

    Carolina Emilia Storniolo

    2014-01-01

    Full Text Available Epidemiological and clinical studies have reported that olive oil reduces the incidence of cardiovascular disease. However, the mechanisms involved in this beneficial effect have not been delineated. The endothelium plays an important role in blood pressure regulation through the release of potent vasodilator and vasoconstrictor agents such as nitric oxide (NO and endothelin-1 (ET-1, respectively, events that are disrupted in type 2 diabetes. Extra virgin olive oil contains polyphenols, compounds that exert a biological action on endothelial function. This study analyzes the effects of olive oil polyphenols on endothelial dysfunction using an in vitro model that simulates the conditions of type 2 diabetes. Our findings show that high glucose and linoleic and oleic acids decrease endothelial NO synthase phosphorylation, and consequently intracellular NO levels, and increase ET-1 synthesis by ECV304 cells. These effects may be related to the stimulation of reactive oxygen species production in these experimental conditions. Hydroxytyrosol and the polyphenol extract from extra virgin olive oil partially reversed the above events. Moreover, we observed that high glucose and free fatty acids reduced NO and increased ET-1 levels induced by acetylcholine through the modulation of intracellular calcium concentrations and endothelial NO synthase phosphorylation, events also reverted by hydroxytyrosol and polyphenol extract. Thus, our results suggest a protective effect of olive oil polyphenols on endothelial dysfunction induced by hyperglycemia and free fatty acids.

  3. Treatment of cork boiling wastewater using chemical oxidation and biodegradation.

    Science.gov (United States)

    Dias-Machado, Manuela; Madeira, Luis M; Nogales, Balbina; Nunes, Olga C; Manaia, Célia M

    2006-06-01

    Three cultures were enriched from cork boiling wastewater using tannic acid as the selective carbon substrate, at 25 degrees C and pH 7.2, 25 degrees C and pH 4.7 and 50 degrees C and pH 4.7. The enrichment culture obtained at neutral pH was composed of five culturable isolates, whereas from each acidic enrichment two bacterial strains were isolated. Mesophilic isolates were Gram negative bacteria belonging to the genera Klebsiella, Pseudomonas, Stenotrophomonas and Burkholderia. Thermophilic isolates were members of the genus Bacillus. Despite the capability of the enrichment cultures to use tannic acid as single carbon and energy source, those cultures were unable to reduce the total polyphenols or the total organic carbon content of cork boiling wastewater. In order to increase the bioavailability of the organic carbon in cork boiling wastewater, biodegradation was preceded by Fenton oxidation. It was demonstrated that the combined process, using small amounts of Fenton reagents and biodegradative inoculum added almost simultaneously to cork boiling wastewater, leads to TOC reductions of more than 90%.

  4. Gibberellic acid nitrite stimulates germination of two species of light-requiring seeds via the nitric oxide pathway.

    Science.gov (United States)

    Jovanović, Vladan; Giba, Zlatko; Djoković, Dejan; Milosavljević, Slobodan; Grubisić, Dragoljub; Konjević, Radomir

    2005-06-01

    We used two species of light-requiring seeds, Paulownia tomentosa, which have absolute light requirement (no germination in darkness), and Stellaria media seeds, which germinate in darkness to a certain extent because of presence of preformed active phytochrome, to obtain results strongly suggesting that gibberellic acid nitrite stimulates seed germination via its capability as a functional NO donor. Exogenous application of gibberellic acid nitrite stimulates gibberellin-insensitive Stellaria media seed germination in darkness as do a wide variety of NO donors. Pure gibberellic acid could replace the light requirement of P. tomentosa seeds, thus enabling them to germinate in darkness. Gibberellic acid nitrite did not have this effect. A stimulative effect from gibberellic acid nitrite could be detected only after exposure of these seeds to short, 10 min, pulse of red light. Taken together, these results suggest that gibberellic activity of gibberellic acid nitrite is lost after nitrosation but, regarding to the presence of -O-NO moiety in the molecule, gibberellic acid nitrite shares stimulative properties in seed germination with other compounds with NO-releasing properties.

  5. Absorption Behavior of Anion Exchange Resin to Minimal Plutonium in 3 to 4 mol/L Nitric Acid Medium

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>The acidity of liquor in the process of plutonium purification using extraction method is 3 to 4 mol/L and liquor contains minimal plutonium of certain concentration, the reclamation of plutonium is usually

  6. 我国硝酸、硝酸铵行业现状及发展趋势——在2011年硝酸硝铵行业工作会上的讲话%Present Status of Nitric Acid and Ammonium Nitrate Industry in China and Development Trend——A Speech at Working Conference on Nitric Acid and Ammonium Nitrate Industry in 2011

    Institute of Scientific and Technical Information of China (English)

    靳小桂

    2011-01-01

    我国硝酸生产以双加压法工艺为主.2010年,我国硝酸产能9 600 kt,产量7 923 kt(实物量),浓硝酸产量2 356 kt;硝酸铵产能6000 kt,产量4 200 kt.硝酸主要下游产品在今后几年内将保持稳定增长,预计未来5年对硝酸的需求年均增长率为7.7%,至2015年用于工业生产的硝酸量将达3 600 kt;随着我国民爆行业产品升级、化肥复合化率提高、硝基复合肥所占比重增大,对硝酸铵的需求也将有较大增长,至2015年磷酸铵产能将达到10 000 kt/a,需硝酸7 900 kt/a.预计3年内我国硝酸产能将达15 000 kt/a,在淘汰落后产能的条件下,仍将有2 000 kt/a产能富余,为此提出了促进硝酸、硝酸铵行业健康发展的建议.%The production of nitric acid in China is mainly based on the dual pressure process. In 2010 the capacity of nitric acid in China was 9 600 kt, the output 7 923 kt (product), and the output of concentrated nitric acid 2 356 kt. The capacity of ammonium nitrate was 6 000 kt, and its output 4 200 kt. The chief downstream products of nitric acid will continue to grow steadily in the next few years, and it is expected that in the next 5 years the demand for nitric acid will increase by 7. 7% a year on the average. By 2015 nitric acid for industrial production will reach 3 600 kt. With the upgrading of the products from the industry for explosives for civil use, increase in the output of compound fertilizers, and rise in the proportion of nitro compound fertilizers, the demand for ammonium nitrate will grow by a large margin. By 2015 the capacity of ammonium nitrate will attain 10 000 kt/a, requiring 7 900 kt/a of nitric acid. In three years the capacity of nitric acid in China will be 15 000 kt/a. Under the conditions of elimination of backward capacity, there is still a surplus of 2 000 kt/a, so suggestions are proposed for the promotion of the sound development of the nitric acid and ammonium nitrate industry.

  7. Study of the nitric acid influence on the production of Ce O{sub 2} with high specific surface area; Estudo da influencia do acido nitrico na obtencao de CeO{sub 2} com alta area superficial especifica

    Energy Technology Data Exchange (ETDEWEB)

    Albanez, Nelma Kunrath; Bressiani, Jose Carlos [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

    1996-12-31

    The cerium oxide (Ce O{sub 2}) main characteristics for use as catalyst in an exhaust gases purification system are: high specific surface area (approximately 30 m{sup 2}/g after calcination at 800 deg C/ 2 hs), and thermal stability. The Ce O{sub 2} powders obtained by conventional route, i.e., precipitation, and submitted high temperature (800 deg C) heat treatments, showed low specific surface area. In this work nitric acid effects on the Ce O{sub 2} surface area values were investigated. The variables studied were nitric acid concentration, humidity content in the raw material, re pulp after leaching, addition of hydrogen peroxide (H{sub 2} O{sub 2}) and starting material specific surface area. By this process, it was possible to obtain powders with specific surface area larger than 40 m{sup 2}/g, after treatment at 800 deg C during two hours. (author) 8 refs., 3 figs., 1 tab.

  8. Techno-Economic Feasibility Study of Renewable Power Systems for a Small-Scale Plasma-Assisted Nitric Acid Plant in Africa

    Directory of Open Access Journals (Sweden)

    Aikaterini Anastasopoulou

    2016-12-01

    Full Text Available The expected world population growth by 2050 is likely to pose great challenges in the global food demand and, in turn, in the fertilizer consumption. The Food and Agricultural Organization of the United Nations has forecasted that 46% of this projected growth will be attributed to Africa. This, in turn, raises further concerns about the sustainability of Africa’s contemporary fertilizer production, considering also its high dependence on fertilizer imports. Based on these facts, a novel “green” route for the synthesis of fertilizers has been considered in the context of the African agriculture by means of plasma technology. More precisely, a techno-economic feasibility study has been conducted for a small-scale plasma-assisted nitric acid plant located in Kenya and South Africa with respect to the electricity provision by renewable energy sources. In this study, standalone solar and wind power systems, as well as a hybrid system, have been assessed for two different electricity loads against certain economic criteria. The relevant simulations have been carried out in HOMER software and the optimized configurations of each examined renewable power system are presented in this study.

  9. Unravelling the potential of nitric acid as a surface modifier for improving the hemocompatibility of metallocene polyethylene for blood contacting devices

    Science.gov (United States)

    Vellayappan, Muthu Vignesh; Muhamad, Ida Idayu

    2016-01-01

    Design of blood compatible surfaces is obligatory to minimize platelet surface interactions and improve the thromboresistance of foreign surfaces when they are utilized as biomaterials particularly for blood contacting devices. Pure metallocene polyethylene (mPE) and nitric acid (HNO3) treated mPE antithrombogenicity and hydrophilicity were investigated. The contact angle of the mPE treated with HNO3 decreased. Surface of mPE and HNO3 treated mPE investigated with FTIR revealed no major changes in its functional groups. 3D Hirox digital microscopy, SEM and AFM images show increased porosity and surface roughness. Blood coagulation assays prothrombin time (PT) and activated partial thromboplastin time (APTT) were delayed significantly (P hemocompatibility of HNO3 treated mPE. To determine that HNO3 does not deteriorate elastic modulus of mPE, the elastic modulus of mPE and HNO3 treated mPE was compared and the result shows no significant difference. Hence, the overall observation suggests that the novel HNO3 treated mPE may hold great promises to be exploited for blood contacting devices like grafts, catheters, and etc. PMID:26819837

  10. Nitric acid activation of graphite granules to increase the performance of the non-catalyzed oxygen reduction reaction (ORR) for MFC applications

    Energy Technology Data Exchange (ETDEWEB)

    Erable, Benjamin [School of Chemical Engineering and Advanced Materials, Newcastle University, Newcastle upon Tyne - NE1 7RU (United Kingdom); Laboratoire de Genie Chimique, CNRS-Universite de Toulouse, 5 rue Paulin Talabot, BP1301, 31106 Toulouse (France); Duteanu, Narcis [School of Chemical Engineering and Advanced Materials, Newcastle University, Newcastle upon Tyne - NE1 7RU (United Kingdom); Faculty of Industrial Chemistry and Environmental Engineering, University ' ' POLITEHNICA' ' Timisoara, 300006 Timisoara (Romania); Kumar, S.M. Senthil; Scott, Keith [School of Chemical Engineering and Advanced Materials, Newcastle University, Newcastle upon Tyne - NE1 7RU (United Kingdom); Feng, Yujie [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, No. 202, Haihe Road, Harbin 150090 (China); Ghangrekar, Makarand M. [School of Chemical Engineering and Advanced Materials, Newcastle University, Newcastle upon Tyne - NE1 7RU (United Kingdom); Department of Civil Engineering, Indian Institute of Technology, Kharagpur - 721302 (India)

    2009-07-15

    Nitric acid and thermal activation of graphite granules were explored to increase the electrocatalytic performance of dissolved oxygen reduction at neutral pH for microbial fuel cell (MFC) applications. Electrochemical experiments showed an improvement of +400 mV in open circuit potential for graphite granules when they were activated. The improvement of ORR performance observed with activated granules was correlated to the increase of Brunauer-Emmett-Teller (BET) surface of the activated material and the emergence of nitrogen superficial groups revealed by X-ray photoelectron spectroscopy (XPS) analysis on its surface. The use of activated graphite granules in the cathodic compartment of a dual-chamber MFC led to a high open circuit voltage of 1050 mV, which is among one of the highest reported so far. The stable performance of this cathode material (current density of 96 A m{sup -3} at +200 mV/Ag-AgCl) over a period of 10 days demonstrated its applicability as a cathode material without any costly noble metal. (author)

  11. Design and Testing of Lab-scale Red Fuming Nitric Acid/Hydroxyl-terminated Polybutadiene Hybrid Rocket Motor for Studying Regression Rate

    Directory of Open Access Journals (Sweden)

    Sankaran Venugopal

    2011-10-01

    Full Text Available This paper presents the design of a hybrid rocket motor and the experiments carried out for investigation of hybrid combustion and regression rates for a combination of liquid oxidiser red fuming nitric acid with solid fuel hydroxyl-terminated Polybutadiene. The regression rate is enhanced with the addition of small quantity of solid oxidiser ammonium perchlorate in the fuel. The characteristics of the combustion products were calculated using the NASA CEA Code and were used in a ballistic code developed for predicting the performance of the hybrid rocket motor. A lab-scale motor was designed and the oxidiser mass flow requirements of the hybrid motor for the above combination of fuel and oxidiser have been calculated using the developed ballistic code. A static rocket motor testing facility has been realised for conducting the hybrid experiments. A series of tests were conducted and proper ignition with stable combustion in the hybrid mode has been established. The regression rate correlations were obtained as a function of the oxidiser mass flux and chamber pressure from the experiments for the various combinations.Defence Science Journal, 2011, 61(6, pp.515-522, DOI:http://dx.doi.org/10.14429/dsj.61.873

  12. Reevaluation of JACS code system benchmark analyses of the heterogeneous system. Fuel rods in U+Pu nitric acid solution system

    Energy Technology Data Exchange (ETDEWEB)

    Takada, Tomoyuki; Miyoshi, Yoshinori; Katakura, Jun-ichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2003-03-01

    In order to perform accuracy evaluation of the critical calculation by the combination of multi-group constant library MGCL and 3-dimensional Monte Carlo code KENO-IV among critical safety evaluation code system JACS, benchmark calculation was carried out from 1980 in 1982. Some cases where the neutron multiplication factor calculated in the heterogeneous system in it was less than 0.95 were seen. In this report, it re-calculated by considering the cause about the heterogeneous system of the U+Pu nitric acid solution systems containing the neutron poison shown in JAERI-M 9859. The present study has shown that the k{sub eff} value less than 0.95 given in JAERI-M 9859 is caused by the fact that the water reflector below a cylindrical container was not taken into consideration in the KENO-IV calculation model. By taking into the water reflector, the KENO-IV calculation gives a k{sub eff} value greater than 0.95 and a good agreement with the experiment. (author)

  13. Solubility of PdI/sub 2/ in nitrate and perchlorate solutions. [For use in spent fuels processing; solvents are water, nitric acid, calcium nitrate, and sodium perchlorate

    Energy Technology Data Exchange (ETDEWEB)

    Horner, D.E.; Mailen, J.C.; Bigelow, H.R.

    1976-01-01

    This paper reports the solubilities of PdI/sub 2/ as measured in nitric acid by a tracer technique and in water, calcium nitrate, and sodium perchlorate solutions by a specific ion electrode technique. The tracer technique measures all the soluble iodine species, whereas the specific ion electrode measures only simple iodide ions (I/sup -/). When compared on the basis of ionic strength, the values obtained in the nitrate solutions by the two methods were in reasonable agreement. The solubilities in perchlorate solution were much higher than in nitrate, possibly because of ionic equilibria involving Pd/sup 4 +/, but this was not resolved in this work. The activity product constant, K/sub ap(PdI/sub 2/)/ = (2.5 +- 0.4) x 10/sup -23/ (25/sup 0/C), was calculated from PdI/sub 2/ solubility in water. With this value and the standard electrode potentials from the literature, the free energy of formation for PdI/sub 2/ was calculated to be --13.6 kcal/mol.

  14. The effect of heating temperature and nitric acid treatments on the performance of Cu- and Zn-based broad spectrum respirator carbons.

    Science.gov (United States)

    Smith, J W H; Romero, J V; Dahn, T R; Dunphy, K; Sullivan, B; Mallay, M; Croll, L M; Reynolds, J H; Andress, C; Dahn, J R

    2011-12-01

    Impregnated activated carbons (IACs) that are used in broad spectrum gas mask applications have historically contained copper and/or zinc impregnants. The addition of an oxidizing agent, such as nitric acid (HNO(3)) can be useful in distributing the metallic impregnants uniformly on the activated carbon substrate. In this work, we study IACs prepared from copper nitrate (Cu(NO(3))(2)) and zinc nitrate (Zn(NO(3))(2)) precursors as a function of HNO(3) content present in the impregnating solution and as a function of heating temperature. The gas adsorption capacity of the IACs was determined by dynamic flow testing using sulfur dioxide (SO(2)), ammonia (NH(3)), hydrogen cyanide (HCN) and cyclohexane (C(6)H(12)) challenge gases under dry and humid conditions. The thermal decomposition and distribution of the impregnant on the activated carbon substrate is studied using X-ray diffraction (XRD), scanning electron microscopy (SEM) and thermal analysis techniques. Relationships between gas adsorption capacity, impregnant distribution and the species of surface impregnants are discussed.

  15. NITRIC OXIDE-ASSOCIATED PROTEIN1 (AtNOA1) is essential for salicylic acid-induced root waving in Arabidopsis thaliana.

    Science.gov (United States)

    Zhao, Xiang; Wang, Jin; Yuan, Jing; Wang, Xi-Li; Zhao, Qing-Ping; Kong, Pei-Tao; Zhang, Xiao

    2015-07-01

    Root waving responses have been attributed to both environmental and genetics factors, but the potential inducers and transducers of root waving remain elusive. Thus, the identification of novel signal elements related to root waving is an intriguing field of research. Genetic, physiological, cytological, live cell imaging, and pharmacological approaches provide strong evidence for the involvement of Arabidopsis thaliana NITRIC OXIDE-ASSOCIATED PROTEIN1 (AtNOA1) in salicylic acid (SA)-induced root waving. SA specially induced root waving, with an overall decrease in root elongation in A. thaliana, and this SA-induced response was disrupted in the Atnoa1 mutant, as well as in nonexpresser of pathogenesis-related genes 1 (npr1), which is defective in SA-mediated plant defense signal transduction, but not in npr3/4 single and double mutants. The expression assays revealed that the abundance of AtNOA1 was significantly increased by application of SA. Genetic and pharmacological analyses showed that SA-induced root waving involved an AtNOA1-dependent Ca(2+) signal transduction pathway, and PIN-FORMED2 (PIN2) -based polar auxin transport possibly plays a crucial role in this process. Our work suggests that SA signaling through NPR1 and AtNOA1 is involved in the control of root waving, which provides new insights into the mechanisms that control root growth behavior on a hard agar surface.

  16. Photosynthetic and antioxidant responses of Liquidambar formosana and Schima superba seedlings to sulfuric-rich and nitric-rich simulated acid rain.

    Science.gov (United States)

    Chen, Juan; Wang, Wen-Hua; Liu, Ting-Wu; Wu, Fei-Hua; Zheng, Hai-Lei

    2013-03-01

    To study whether differential responses occur in photosynthesis and antioxidant system for seedlings of Liquidambar formosana, an acid rain (AR)-sensitive tree species and Schima superba, an AR-tolerant tree species treated with three types of pH 3.0 simulated AR (SiAR) including sulfuric-rich (S-SiAR), nitric-rich (N-SiAR), sulfate and nitrate mixed (SN-SiAR), we investigated the changes of leaf necrosis, chlorophyll content, soluble protein and proline content, photosynthesis and chlorophyll fluorescence characteristics, reactive oxygen species production, membrane lipid peroxidation, small molecular antioxidant content, antioxidant enzyme activities and related protein expressions. Our results showed that SiAR significantly caused leaf necrosis, inhibited photosynthesis, induced superoxide radical and hydrogen peroxide generation, aggravated membrane lipid peroxidation, changed antioxidant enzyme activities, modified related protein expressions such as Cu/Zn superoxide dismutase (SOD), l-ascorbate peroxidase (APX, EC 1. 11. 1. 11), glutathione S transferase (GST, EC 2. 5. 1. 18) and Rubisco large subunit (RuBISCO LSU), altered non-protein thiols (NPT) and glutathione (GSH) content in leaves of L. formosana and S. superba. Taken together, we concluded that the damages caused by SiAR in L. formosana were more severe and suffered from more negative impacts than in S. superba. S-SiAR induced more serious damages for the plants than did SN-SiAR and N-SiAR.

  17. Nitric oxide suppresses the inhibitory effect of abscisic acid on seed germination by S-nitrosylation of SnRK2 proteins.

    Science.gov (United States)

    Wang, Pengcheng; Zhu, Jian-Kang; Lang, Zhaobo

    2015-01-01

    Nitric oxide (NO) plays important roles in plant development, and biotic and abiotic stress responses. In a recent study, we showed that endogenous NO negatively regulates abscisic acid (ABA) signaling in guard cells by inhibiting sucrose nonfermenting 1 (SNF1)-related protein kinase 2.6 (SnRK2.6)/open stomata 1(OST1) through S-nitrosylation. Application of NO breaks seed dormancy and alleviates the inhibitory effect of ABA on seed germination and early seedling growth, but it is unclear how NO functions at the stages of seed germination and early seedling development. Here, we show that like SnRK2.6, SnRK2.2 can be inactivated by S-nitrosoglutathione (GSNO) treatment through S-nitrosylation. SnRK2.2 and the closely related SnRK2.3 are known to play redundant roles in ABA inhibition of seed germination in Arabidopsis. We found that treatment with the NO donor SNP phenocopies the snrk2.2snrk2.3 double mutant in conferring ABA insensitivity at the stages of seed germination and early seedling growth. Our results suggest that NO negatively regulates ABA signaling in germination and early seedling growth through S-nitrosylation of SnRK2.2 and SnRK2.3.

  18. The influence of nitric oxide and oxalic acid on Triticum aestivum L. infected by Septoria tritici Blotch

    Directory of Open Access Journals (Sweden)

    Iryna V. Zhuk

    2013-04-01

    Full Text Available The realization of productivity of Triticum aestivumL. modern cultivars is limited by yield losses caused by fungus diseases which intensively develop under high level of humidity and air temperatures. The usage of elicitors is the way to induce the plant immunity of cereals and minimize the pesticide pollution of the environment. It is established that the additive effect of elicitor (oxalic acid and NO signal molecule decrease the stress after the action of biotic factor (Septoria triticiBlotch in two spring wheat cultivars – ‘Nedra’and ‘Etud’in the field experiment conditions. The effect of oxalic acid was to decrease the yield losses by the way of decreasing the degree of corns’ infection by pathogen. NO donor manifests the qualities of signal molecule and growth regulator under biotic stress that promoted the realization of wheat potential productivity.

  19. Nitric oxide mediates the fungal elicitor-induced puerarin biosynthesis in Pueraria thomsonii Benth. suspension cells through a salicylic acid (SA)-dependent and a jasmonic acid (JA)-dependent signal pathway

    Institute of Scientific and Technical Information of China (English)

    XU Maojun; DONG Jufang; ZHU Muyuan

    2006-01-01

    Nitric oxide (NO) has emerged as a key signaling molecule in plant secondary metabolite biosynthesis recently. In order to investigate the molecular basis of NO signaling in elicitor-induced secondary metabolite biosynthesis of plant cells, we determined the contents of NO, salicylic acid (SA), jasmonic acid (JA), and puerarin in Pueraria thomsonii Benth. suspension cells treated with the elicitors prepared from cell walls of Penicillium citrinum. The results showed that the fungal elicitor induced NO burst, SA accumulation and puerarin production of P. thomsonii Benth. cells. The elicitor-induced SA accumulation and puerarin production was suppressed by nitric oxide specific scavenger cPITO, indicating that NO was essential for elicitor-induced SA and puerarin biosynthesis in P. thomsonii Benth. cells. In transgenic NahG P. thomsonii Benth. cells, the fungal elicitor also induced puerarin biosynthesis, NO burst, and JA accumulation, though the SA biosynthesis was impaired. The elicitor-induced JA accumulation in transgenic cells was blocked by cPITO, which suggested that JA acted downstream of NO and its biosynthesis was controlled by NO. External application of NO via its donor sodium nitroprusside (SNP) enhanced puerarin biosynthesis in transgenic NahG P. thomsonii Benth. cells, and the NO-triggered puerarin biosynthesis was suppressed by JA inhibitors IBU and NDGA, which indicated that NO induced puerarin production through a JA-dependent signal pathway in the transgenic cells. Exogenous application of SA suppressed the elicitor-induced JA biosynthesis and reversed the inhibition of IBU and NDGA on elicitor-induced puerarin accumulation in transgenic cells, which indicated that SA inhibited JA biosynthesis in the cells and that SA might be used as a substitute for JA to mediate the elicitor- and NO-induced puerarin biosynthesis. It was, therefore, concluded that NO might mediate the elicitor-induced puerarin biosynthesis through SA- and JA-dependent signal

  20. 硝酸浸取磷矿制轻质碳酸钙工艺研究%Preparation of light calcium carbonate by nitric acid leaching phosphate ore

    Institute of Scientific and Technical Information of China (English)

    胡兆平; 贾洪秀; 庞世花; 刘阳; 贾亮

    2013-01-01

    Calcium nitrate crystal can be obtained by freezing crystallization method from acid solution acquired from nitric acid extracting phosphate rock.After that,light calcium carbonate was prepared by carbonization reaction between ammonium hydrogen carbonate and calcium nitrate crystal.Results show that,the initial carbonization reaction temperature was the normal temperature,mass fraction of calcium nitrate solution was about 23%,ammonium hydrogen carbonate and ammonia dosages were both 110% of theoretical addition amounts,and products were washed by four times of product weight washing water.All quality indexes of the product can meet the standard of Industrial Precipitated Calcium Carbonate,HG/T 2226-2000.%硝酸萃取磷矿后的酸解液,通过冷冻结晶法得到硝酸钙晶体,然后以硝酸钙为原料,通过加入碳酸氢铵进行碳化制取轻质碳酸钙.结果表明,碳化反应的初始反应温度为常温,硝酸钙溶液的质量分数为23%左右,碳酸氢铵和氨水按理论加入量的110%进行反应,用产品质量的4倍洗水量洗涤产品,制备的轻质碳酸钙产品各项指标均达到HG/T 2226-2000《工业沉淀碳酸钙》标准的要求.

  1. DNA fragmentation dynamics allows the assessment of cryptic sperm damage in human: Evaluation of exposure to ionizing radiation, hyperthermia, acidic pH and nitric oxide

    Energy Technology Data Exchange (ETDEWEB)

    Santiso, Rebeca; Tamayo, Maria [Laboratorio de Genetica Molecular y Radiobiologia, Centro Oncologico de Galicia, Doctor Camilo Veiras 1, 15009-A Coruna (Spain); Genetics Unit, INIBIC-Complejo Hospitalario Universitario A Coruna (CHUAC), As Xubias, 84, 15006-A Coruna (Spain); Gosalvez, Jaime [Genetics Unit, Facultad de Biologia, Universidad Autonoma de Madrid, Ciudad Universitaria de Cantoblanco, 28049 Madrid (Spain); Johnston, Steve [School of Agriculture and Food Science, University of Queensland, Gatton 4343 (Australia); Marino, Alfonso [Servicio de Oncologia Radioterapica, Centro Oncologico de Galicia, Doctor Camilo Veiras 1, 15009-A Coruna (Spain); Fernandez, Carlos; Losada, Carlos [Servicio de Radiofisica, Centro Oncologico de Galicia, Doctor Camilo Veiras 1, 15009-A Coruna (Spain); Fernandez, Jose Luis, E-mail: Jose.Luis.Fernandez.Garcia@sergas.es [Laboratorio de Genetica Molecular y Radiobiologia, Centro Oncologico de Galicia, Doctor Camilo Veiras 1, 15009-A Coruna (Spain); Genetics Unit, INIBIC-Complejo Hospitalario Universitario A Coruna (CHUAC), As Xubias, 84, 15006-A Coruna (Spain)

    2012-06-01

    Sperm DNA fragmentation (SDF) is not a static seminal parameter, since the longevity of sperm DNA decreases progressively with time following ejaculation or thawing. While the dynamics of SDF is a species-specific characteristic, in the case of humans, there is still significant variation within patients. To evaluate the suitability of the dynamic SDF assay to assess the adverse effects of agents that cause genetic damage, fresh semen samples from different donors were exposed in vitro to (1) increasing acute doses of ionizing radiation, (2) elevated temperature (41 Degree-Sign C and 45 Degree-Sign C), (3) acidic pH (pH 4) and (4) the nitric oxide (NO) donor sodium nitroprusside (SNP). Sperm DNA fragmentation was analyzed after an incubation period of chronic (24 h), or acute (1 h) exposure to each treatment followed by incubation at 37 Degree-Sign C over a period of 24 h. SDF was assessed using the sperm chromatin dispersion (SCD) test. Dynamic SDF for each treatment was analyzed using Kaplan-Meier survival curves. All agents, except for ionizing radiation, accelerated SDF kinetics following chronic exposure over a 24 h period. Transient exposure to NO and heat but not acidic pH increased the basal (T0) level of SDF. Despite the removal of the three toxicants, the remaining sperm following acute exposure showed a decrease in their expected DNA longevity. It is concluded that the assessment of sperm DNA fragmentation dynamics is an effective methodological approach for revealing latent damage associated with toxicants that is not initially expressed following a single initial observation of SDF.

  2. COPPER AMINE OXIDASE1 (CuA01)of Arabidopsis thaliana Contributes to Abscisic Acid-and Polyamine-Induced Nitric Oxide Biosynthesis and Abscisic Acid Signal Transduction

    Institute of Scientific and Technical Information of China (English)

    Rinukshi Wimalasekera; Corina Villar; Tahmina Begum; Günther F. E. Scherer

    2011-01-01

    Polyamines (PA), polyamine oxidases, copper amine oxidases, and nitric oxide (NO)play important roles in physiology and stress responses in plants. NO biosynthesis as a result of catabolism of PA by polyamine oxidases and copper amine oxidases may explain in part PA-mediated responses. Involvement of a copper amine oxidase gene, COPPER AMINE OXIDASE1 (CuA01), of Arabidopsis was tested for its role in stress responses using the knockouts cuaol.1 and cuaol-2. PA-induced and ABA-induced NO production investigated by fluorometry and fluorescence microscopy showed that the cuaol-1 and cuaol-2 are impaired in NO production, suggesting a function of CuAO1 in PA and ABA-mediated NO production. Furthermore, we found a PA-dependent increase in protein S-nitrosylation. The addition of PA and ABA also resulted in HO increases, cuaol-1 and cuaol-2 showed less sensitivity to exogenous ABA supplementation during ger-mination, seedling establishment, and root growth inhibition as compared to wild-type. In response to ABA treatment,expression levels of the stress-responsive genes RD29A and ADH1 were significantly lower in the knockouts. These obser-vations characterize cuaol-1 and cuaol-2 as ABA-insensitive mutants. Taken together, our findings extend the ABA signal transduction network to include CuAO1 as one potential contributor to enhanced NO production by ABA.

  3. Instability in flow boiling in microchannels

    CERN Document Server

    Saha, Sujoy Kumar

    2016-01-01

    This Brief addresses the phenomena of instability in flow boiling in microchannels occurring in high heat flux electronic cooling. A companion edition in the SpringerBrief Subseries on Thermal Engineering and Applied Science to “Critical Heat Flux in Flow Boiling in Microchannels,” and "Heat Transfer and Pressure Drop in Flow Boiling in Microchannels,"by the same author team, this volume is idea for professionals, researchers, and graduate students concerned with electronic cooling.

  4. Gamma heated subassembly for sodium boiling experiments

    Energy Technology Data Exchange (ETDEWEB)

    Artus, S.C.

    1975-01-01

    The design of a system to boil sodium in an LMFBR is examined. This design should be regarded as a first step in a series of boiling experiments. The reactor chosen for the design of the boiling apparatus is the Experimental Breeder Reactor-II (EBR-II), located at the National Reactor Testing Station in Idaho. Criteria broadly classified as design objectives and design requirements are discussed.

  5. Methods of analysis by the U.S. Geological Survey National Water Quality Laboratory; comparison of a nitric acid in-bottle digestion procedure to other whole-water digestion procedures

    Science.gov (United States)

    Garbarino, John R.; Hoffman, Gerald L.

    1999-01-01

    A hydrochloric acid in-bottle digestion procedure is used to partially digest wholewater samples prior to determining recoverable elements by various analytical methods. The use of hydrochloric acid is problematic for some methods of analysis because of spectral interference. The inbottle digestion procedure has been modified to eliminate such interference by using nitric acid instead of hydrochloric acid in the digestion. Implications of this modification are evaluated by comparing results for a series of synthetic whole-water samples. Results are also compared with those obtained by using U.S. Environmental Protection Agency (1994) (USEPA) Method 200.2 total-recoverable digestion procedure. Percentage yields that use the nitric acid inbottle digestion procedure are within 10 percent of the hydrochloric acid in-bottle yields for 25 of the 26 elements determined in two of the three synthetic whole-water samples tested. Differences in percentage yields for the third synthetic whole-water sample were greater than 10 percent for 16 of the 26 elements determined. The USEPA method was the most rigorous for solubilizing elements from particulate matter in all three synthetic whole-water samples. Nevertheless, the variability in the percentage yield by using the USEPA digestion procedure was generally greater than the in-bottle digestion procedure, presumably because of the difficulty in controlling the digestion conditions accurately.

  6. Pool Boiling of Hydrocarbon Mixtures on Water

    Energy Technology Data Exchange (ETDEWEB)

    Boee, R.

    1996-09-01

    In maritime transport of liquefied natural gas (LNG) there is a risk of spilling cryogenic liquid onto water. The present doctoral thesis discusses transient boiling experiments in which liquid hydrocarbons were poured onto water and left to boil off. Composition changes during boiling are believed to be connected with the initiation of rapid phase transition in LNG spilled on water. 64 experimental runs were carried out, 14 using pure liquid methane, 36 using methane-ethane, and 14 using methane-propane binary mixtures of different composition. The water surface was open to the atmosphere and covered an area of 200 cm{sup 2} at 25 - 40{sup o}C. The heat flux was obtained by monitoring the change of mass vs time. The void fraction in the boiling layer was measured with a gamma densitometer, and a method for adapting this measurement concept to the case of a boiling cryogenic liquid mixture is suggested. Significant differences in the boil-off characteristics between pure methane and binary mixtures revealed by previous studies are confirmed. Pure methane is in film boiling, whereas the mixtures appear to enter the transitional boiling regime with only small amounts of the second component added. The results indicate that the common assumption that LNG will be in film boiling on water because of the high temperature difference, may be questioned. Comparison with previous work shows that at this small scale the results are influenced by the experimental apparatus and procedures. 66 refs., 76 figs., 28 tabs.

  7. Duality of boiling systems and uncertainty phenomena

    Institute of Scientific and Technical Information of China (English)

    柴立合; 彭晓峰; 王补宣

    2000-01-01

    Interactions among dry patches at high heat flux are theoretically analyzed. The high heat flux boiling experiments on metal plate wall with different materials and thickness are correspondingly conducted. The duality of boiling system, i.e. hydrodynamic performance and self-organized performance is identified. A unified explanation of hydrodynamic models and dry patches models is given. The scatter and uncertainty in boiling data can be mainly attributed to the intrinsic duality, but not the sole surface effects. The present experimental results explain why the deviation point at high flux boiling is seen only on occasion and why the self-organization of dry patches is often ignored in available literature.

  8. Characteristic and mechanism of Th{sup 4+} sorption from nitric acid solutions by rice and wheat bran

    Energy Technology Data Exchange (ETDEWEB)

    Monji, Akbar Boveiri [Kharazmi Univ., Tehran (Iran, Islamic Republic of). Faculty of Chemistry; Nuclear Science and Technology Research Institute, Tehran (Iran, Islamic Republic of); Ghoulipour, Vanik [Kharazmi Univ., Tehran (Iran, Islamic Republic of). Faculty of Chemistry; Mallah, Mohammad Hassan [Nuclear Science and Technology Research Institute, Tehran (Iran, Islamic Republic of)

    2015-07-01

    In line with our previously conducted researches, various instrumental methods were applied to evaluate the adsorption features and mechanism of Th{sup 4+} from highly acidic solution (4M HNO{sub 3}) by rice and wheat bran. Although the results of cation exchange confirmed the existence of ion-exchange interaction in Th{sup 4+} adsorption, it had a trivial contribution in the biosorption process. The presence of Th{sup 4+} ions on the biomass surface was obviously revealed in SEM images and EDS elemental analysis. Moreover, the linkage of C=O, O-H and N-H functional groups on the biomass surface with Th{sup 4+} ions was clearly represented in the ATR-FTIR spectroscopic analysis. Additionally, desorption studies indicated that ammonium oxalate (>81.3%) and ammonium carbonate (>75.4%) were effective in desorbing Th{sup 4+} from the biomass surface due to strong interactions of hard functional groups of C=O with Th{sup 4+}. The overall observations unfold the fact that electrostatic complexation mechanism is dominant between biomass and Th{sup 4+} ions.

  9. 稀土氟化物在硝酸中溶解性质的研究%Solubility of rare earth fluorides in nitric acid

    Institute of Scientific and Technical Information of China (English)

    仇婷婷; 彭佳; 何淑华; 郑小北; 刘玉侠; 周伟; 张岚

    2015-01-01

    Background: A varity of rare-earth fluorides can be produced with thorium uranium fuel circulating post-processing. These fluorides need to be dissolubled in solvent for seperation and contents measurement.Purpose: This paper aims to develop a fast and efficient pretreatment method to dissolve slightly soluble rare earth fluorides in nitric acid.Methods: Rare earth fluorides related to the thorium molten salt reactor (TMSR) fuel circulating post-processing including NdF3, EuF3, GdF3 and CeF3 were studied by using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES). After 2-h microwave digestion at temperature of 190 ºC, the maximum solubility of these fluorides in 10 mL nitric acid (16 mol·L−1) is determined by ICP-AES.Results: The saturated concentration varies from 2.5 g·L−1 to 3.9g·L−1, which are two or three orders of magnitude higher than their solubility reported in previous literature. The standard deviation (n=3) of measurement by ICP-AES is under 4.2% and the linear correlation coefficient (r) is in the range of 0.999 47−0.999 96.Conclusion:An efficient chemical procedure for dissolving some rare earth fluorides has been developed. It provides a reference for pretreatment of insoluble rare earth fluorides in the solid molten salt samples of thorium uranium fuel circulating post-processing.%采用微波消解-电感耦合等离子体原子发射光谱(Inductively Coupled Plasma Atomic Emission Spectroscopy, ICP-AES),系统研究了钍铀燃料循环后处理中4种典型稀土氟化物(NdF3、EuF3、GdF3、CeF3)在硝酸中的溶解性质。结果表明,在10 mL、浓度为16 mol·L−1的硝酸中,微波消解2 h,190ºC下,4种稀土氟化物的最大溶解量可达2.5−3.9 g·L−1,均比文献报道的数值高2−3个数量级;采用ICP-AES测试溶解液,线性范围0.99947−0.99996,标准偏差SD≤4.2%(n=3),该溶解方法旨在为核燃料后处理流程中含有难溶稀土氟

  10. Boiling flow through diverging microchannel

    Indian Academy of Sciences (India)

    V S Duryodhan; S G Singh; Amit Agrawal

    2013-12-01

    An experimental study of flow boiling through diverging microchannel has been carried out in this work, with the aim of understanding boiling in nonuniform cross-section microchannel. Diverging microchannel of 4° of divergence angle and 146 m hydraulic diameter (calculated at mid-length) has been employed for the present study with deionised water as working fluid. Effect of mass flux (118–1182 kg/m2-s) and heat flux (1.6–19.2 W/cm2) on single and two-phase pressure drop and average heat transfer coefficient has been studied. Concurrently, flow visualization is carried out to document the various flow regimes and to correlate the pressure drop and average heat transfer coefficient to the underlying flow regime. Four flow regimes have been identified from the measurements: bubbly, slug, slug–annular and periodic dry-out/rewetting. Variation of pressure drop with heat flux shows one maxima which corresponds to transition from bubbly to slug flow. It is shown that significantly large heat transfer coefficient (up to 107 kW/m2-K) can be attained for such systems, for small pressure drop penalty and with good flow stability.

  11. Catalytic abatement of nitrous oxide from nitric and production

    NARCIS (Netherlands)

    Oonk, J.

    1998-01-01

    Nitric acid production is identified as a main source of nitrous oxide. Options for emission reduction however are not available. TNO and Hydro Agri studied the technological and economic feasibility of catalytic decomposition of nitrous oxide in nitric acid tail-gases. Although in literature promis

  12. Intracerebroventricular administration of Shiga toxin type 2 altered the expression levels of neuronal nitric oxide synthase and glial fibrillary acidic protein in rat brains.

    Science.gov (United States)

    Boccoli, Javier; Loidl, C Fabián; Lopez-Costa, Juan José; Creydt, Virginia Pistone; Ibarra, Cristina; Goldstein, Jorge

    2008-09-16

    Shiga toxin (Stx) from enterohemorrhagic Escherichia coli (STEC) is the main cause of hemorrhagic colitis which may derive into Hemolytic Uremic Syndrome (HUS) and acute encephalopathy, one of the major risk factors for infant death caused by the toxin. We have previously demonstrated that intracerebroventricular administration of Stx2 causes neuronal death and glial cell damage in rat brains. In the present work, we observed that the intracerebroventricular administration of Stx2 increased the expression of glial fibrillary acidic protein (GFAP) leading to astrogliosis. Confocal microscopy showed reactive astrocytes in contact with Stx2-containing neurons. Immunocolocalization of increased GFAP and Stx2 in astrocytes was also observed. This insult in the brain was correlated with changes in the expression and activity of neuronal nitric oxide synthase (nNOS) by using the NADPH-diaphorase histochemical technique (NADPH-d HT). A significant decrease in NOS/NADPH-d-positive neurons and NOS/NADPH-d activity was observed in cerebral cortex and striatum, whereas an opposite effect was found in the hypothalamic paraventricular nucleus. We concluded that the i.c.v. administration of Stx2 promotes a typical pattern of brain injury showing reactive astrocytes and an alteration in the number and activity of nNOS/NADPH-d. According to the functional state of nNOS/NADPH-d and to brain cell morphology data, it could be inferred that the i.c.v. administration of Stx2 leads to either a neurodegenerative or a neuroprotective mechanism in the affected brain areas. The present animal model resembles the encephalopathy developed in Hemolytic Uremic Syndrome (HUS) patients by STEC intoxication.

  13. Chlorogenic acid improves ex vivo vessel function and protects endothelial cells against HOCl-induced oxidative damage, via increased production of nitric oxide and induction of Hmox-1.

    Science.gov (United States)

    Jiang, Rujia; Hodgson, Jonathan M; Mas, Emilie; Croft, Kevin D; Ward, Natalie C

    2016-01-01

    Dietary polyphenols are potential contributors toward improved cardiovascular health. Coffee is one of the richest sources of dietary polyphenols in a coffee-drinking population, the most abundant form being chlorogenic acid (CGA). Endothelial dysfunction is an early and major risk factor for cardiovascular disease. Nitric oxide (NO) is a key factor in regulation of endothelial function. Heme oxygenase-1 (Hmox-1), an inducible isoform of heme oxygenase that is produced in response to stressors such as oxidative stress, may also play a role in vascular protection. The aim of this study was to investigate the effect of CGA on endothelial function with oxidant-induced damage in isolated aortic rings from C57BL mice. We further examine the mechanism by investigating cell viability, activation of eNOS and induction of Hmox-1 in human aortic endothelial cells (HAECs). We found that pretreatment of isolated aortic rings with 10-μM CGA-protected vessels against HOCl-induced endothelial dysfunction (P<0.05). Pretreatment of cultured HAECs with 10-μM CGA increased endothelial cell viability following exposure to HOCl (P<0.05). Moreover, CGA increased NO production in HAECs in a dose-dependent manner, peaking at 6 h (P<0.05). CGA at 5 μM and 10 μM increased eNOS dimerization at 6 h and induced Hmox-1 protein expression at 6 h and 24 h in HAECs. These results are consistent with the cardiovascular protective effects of coffee polyphenols and demonstrate that CGA can protect vessels and cultured endothelial cells against oxidant-induced damage. The mechanism behind the beneficial effect of CGA appears to be in part via increased production of NO and induction of Hmox-1.

  14. The poly-γ-d-glutamic acid capsule surrogate of the Bacillus anthracis capsule induces nitric oxide production via the platelet activating factor receptor signaling pathway.

    Science.gov (United States)

    Lee, Hae-Ri; Jeon, Jun Ho; Park, Ok-Kyu; Chun, Jeong-Hoon; Park, Jungchan; Rhie, Gi-Eun

    2015-12-01

    The poly-γ-d-glutamic acid (PGA) capsule, a major virulence factor of Bacillus anthracis, confers protection of the bacillus from phagocytosis and allows its unimpeded growth in the host. PGA capsules released from B. anthracis are associated with lethal toxin in the blood of experimentally infected animals and enhance the cytotoxic effect of lethal toxin on macrophages. In addition, PGA capsule itself activates macrophages and dendritic cells to produce proinflammatory cytokine such as IL-1β, indicating multiple roles of PGA capsule in anthrax pathogenesis. Here we report that PGA capsule of Bacillus licheniformis, a surrogate of B. anthracis capsule, induces production of nitric oxide (NO) in RAW264.7 cells and bone marrow-derived macrophages. NO production was induced by PGA in a dose-dependent manner and was markedly reduced by inhibitors of inducible NO synthase (iNOS), suggesting iNOS-dependent production of NO. Induction of NO production by PGA was not observed in macrophages from TLR2-deficient mice and was also substantially inhibited in RAW264.7 cells by pretreatment of TLR2 blocking antibody. Subsequently, the downstream signaling events such as ERK, JNK and p38 of MAPK pathways as well as NF-κB activation were required for PGA-induced NO production. In addition, the induced NO production was significantly suppressed by treatment with antagonists of platelet activating factor receptor (PAFR) or PAFR siRNA, and mediated through PAFR/Jak2/STAT-1 signaling pathway. These findings suggest that PGA capsule induces NO production in macrophages by triggering both TLR2 and PAFR signaling pathways which lead to activation of NF-kB and STAT-1, respectively.

  15. Potent odorants characterize the aroma quality of leaves and stalks in raw and boiled celery.

    Science.gov (United States)

    Kurobayashi, Yoshiko; Kouno, Emi; Fujita, Akira; Morimitsu, Yasujiro; Kubota, Kikue

    2006-04-01

    The raw and boiled odors of celery leaves and stalks were investigated. Among 12 compounds identified as potent odorants, 3-n-butylphthalide 1, sedanenolide 2, and trans- and cis-sedanolides 3, 4 were assessed to be most contributive to the overall odor of celery. These three phthalides, (3E,5Z)-1,3,5-undecatriene, myrcene, and (E)-2-nonenal were common to both raw and boiled materials. Two compounds, ((Z)-3-hexenal and (Z)-3-hexenol), were dominant in raw materials and four compounds, (2-methylbutanoic acid, sotolon, beta-damascenone, and beta-ionone), were dominant in boiled materials. Sensory evaluations were performed on natural celery odor and a series of reconstructed model aromas by assigning each intensity ratings for a set of seven odor qualities which aptly describe the odors of raw and boiled celery. According to the evaluation results, six common components contributed to the moderate odor of raw celery, two components dominant in raw materials enhanced the raw celery character, and four components dominant in boiled materials reduced the raw celery character and enhanced the boiled celery character. It was clarified that boiling-induced changes in celery odor were not affected by the amounts of phthalides, but by thermally generated compounds such as sotolon, beta-damascenone, and beta-ionone, which reduce the "green spicy" note.

  16. Transient boiling crisis of cryogenic liquids

    NARCIS (Netherlands)

    Deev, [No Value; Kharitonov, VS; Kutsenko, KV; Lavrukhin, AA

    2004-01-01

    This paper introduces a new physical model of boiling crisis under rapid increase of power on the heated surface. The calculation of the time interval of the transition to film boiling in cryogenic liquids was carried out depending on heat flux and pressure. The obtained results are in good agreemen

  17. Boiling turbulent Rayleigh-Bénard convection

    NARCIS (Netherlands)

    Lakkaraju, R.

    2013-01-01

    A fundamental understanding of liquid-vapor phase transitions, mainly boiling phenomenon, is essential due to its omnipresence in science and technology. In industries, many empirical correlations exist on the heat transport to get an optimized and efficient thermal design of the boiling equipment.

  18. L-theanine, a Component of Green Tea Prevents 3-Nitropropionic Acid (3-NP)-Induced Striatal Toxicity by Modulating Nitric Oxide Pathway.

    Science.gov (United States)

    Jamwal, Sumit; Kumar, Puneet

    2017-04-01

    L-theanine is unique amino acid which readily crosses blood brain barrier and possesses neuroprotective potential against neurodegenerative disorders including Huntington disease (HD). HD is characterized by selective loss of GABAergic medium spiny neurons. 3-nitropropionic acid (3-NP) induces a spectrum of HD-like neuropathology in rat striatum and widely used as experimental tool to study HD. Therefore, the present study was intended to investigate the effect of L-theanine against 3-NP-induced striatal toxicity and to explore its possible mechanism. Rats were administered with 3-NP for 21 days. L-theanine was given once a day, 1 h prior to 3-NP treatment for 21 days and L-NAME (10 mg/kg, i.p.), NO inhibitor and L-arginine (50 mg/kg; i.p.), NO precursor were administered 1 h prior to L-theanine treatment. Body weight and behavioral observation were made on weekly basis. On the 22nd day, animals were sacrificed, and the striatum was isolated for biochemical (LPO, GSH, and nitrite), pro-inflammatory cytokines and neurochemical analysis. 3-NP treatment significantly altered body weight, locomotor activity, motor coordination, mitochondrial complex-II activity, oxidative defense, pro-inflammatory mediators, and striatal neurotransmitters level. L-theanine pre-treatment (25 and 50 mg/kg/day, p.o.) significantly prevented these alterations. In addition, concurrent treatment of L-NAME with L-theanine (25 mg/kg/day, p.o.) significantly enhanced protective effect of L-theanine (25 mg/kg/day, p.o.) whereas concurrent treatment of L-arginine with L-theanine (50 mg/kg/day, p.o.) significantly ameliorated the protective effect of L-theanine (50 mg/kg/day, p.o.). The neuroprotective potential of L-theanine involves inhibition of detrimental nitric oxide production and prevention of neurotransmitters alteration in the striatum.

  19. Summary Report on Gamma Radiolysis of TBP/n-dodecane in the Presence of Nitric Acid Using the Radiolysis/Hydrolysis Test Loop

    Energy Technology Data Exchange (ETDEWEB)

    Dean R. Peterman; Bruce J. Mincher; Catherine L. Riddle; Richard D. Tillotson

    2010-08-01

    Design and installation has been completed for a state-of-the-art radiolysis/hydrolysis test loop system. The system is used to evaluate the effects of gamma radiolysis and acid hydrolysis on the stability and performance of solvent extraction process solvents. The test loop is comprised of two main sections; the solvent irradiation and hydrolysis loop and the solvent reconditioning loop. In the solvent irradiation and hydrolysis loop, aqueous and organic phases are mixed and circulated through a gamma irradiator until the desired absorbed dose is achieved. Irradiation of the mixed phases is more representative of actual conditions in a solvent extraction process. Additionally, the contact of the organic phase with the aqueous phase will subject the solvent components to hydrolysis. This hydrolysis can be accelerated by controlling the system at an elevated temperature. At defined intervals, the organic from the irradiation/hydrolysis loop will be transferred to the solvent reconditioning loop where the solvent is contacted with scrub, strip, and solvent wash solutions which simulate process flowsheet conditions. These two processes are repeated until the total desired dose is achieved. Since all viable solvent extraction components in an advanced fuel cycle must exhibit high radiolytic and hydrolytic stability, this test loop is not limited to any one solvent system but is applicable to all systems of interest. Also, the test loop is not limited to testing of process flowsheets. It is also a valuable tool in support of fundamental research on newly identified extractants/modifiers and the impact of gamma radiation on their stability in a dynamic environment. The investigation of the radiolysis of a TBP/n-dodecane process solvent in contact with aqueous nitric acid has been performed. These studies were intended to confirm/optimize the operability of the test loop system. Additionally, these data are directly applicable to numerous other solvent extraction

  20. Characterization of Group V Dubnium Homologs on DGA Extraction Chromatography Resin from Nitric and Hydrofluoric Acid Matrices

    Energy Technology Data Exchange (ETDEWEB)

    Despotopulos, J D; Sudowe, R

    2012-02-21

    somewhere between Nb and Pa. Much more recent studies have examined the properties of Db from HNO{sub 3}/HF matrices, and suggest Db forms complexes similar to those of Pa. Very little experimental work into the behavior of element 114 has been performed. Thermochromatography experiments of three atoms of element 114 indicate that the element 114 is at least as volatile as Hg, At, and element 112. Lead was shown to deposit on gold at temperatures about 1000 C higher than the atoms of element 114. Results indicate a substantially increased stability of element 114. No liquid phase studies of element 114 or its homologs (Pb, Sn, Ge) or pseudo-homologs (Hg, Cd) have been performed. Theoretical predictions indicate that element 114 is should have a much more stable +2 oxidation state and neutral state than Pb, which would result in element 114 being less reactive and less metallic than Pb. The relativistic effects on the 7p{sub 1/2} electrons are predicted to cause a diagonal relationship to be introduced into the periodic table. Therefore, 114{sup 2+} is expected to behave as if it were somewhere between Hg{sup 2+}, Cd{sup 2+}, and Pb{sup 2+}. In this work two commercially available extraction chromatography resins are evaluated, one for the separation of Db homologs and pseudo?homologs from each other as well as from potential interfering elements such as Group IV Rf homologs and actinides, and the other for separation of element 114 homologs. One resin, Eichrom's DGA resin, contains a N,N,N',N'-tetra-n-octyldiglycolamide extractant, which separates analytes based on both size and charge characteristics of the solvated metal species, coated on an inert support. The DGA resin was examined for Db chemical systems, and shows a high degree of selectivity for tri-, tetra-, and hexavalent metal ions in multiple acid matrices with fast kinetics. The other resin, Eichrom's Pb resin, contains a di-t-butylcyclohexano 18-crown-6 extractant with isodecanol solvent

  1. Treatment of cork boiling wastewater using chemical oxidation and biodegradation

    OpenAIRE

    Machado, Manuela Dias; Madeira, Luis M.; Nogales, Balbina; Nunes, Olga C; Manaia, Célia M.

    2006-01-01

    Three cultures were enriched from cork boiling wastewater using tannic acid as the selective carbon substrate, at 25 C and pH 7.2, 25 C and pH 4.7 and 50 C and pH 4.7. The enrichment culture obtained at neutral pH was composed of five culturable isolates, whereas from each acidic enrichment two bacterial strains were isolated. Mesophilic isolates were Gram negative bacteria belonging to the genera Klebsiella, Pseudomonas, Stenotrophomonas and Burkholderia. Thermophilic isolates we...

  2. Silver extraction using nitric acid from lead-zinc mine tail slag by response surface design%响应面法优化硝酸浸铅锌矿尾渣回收银工艺研究

    Institute of Scientific and Technical Information of China (English)

    杨彦松

    2011-01-01

    以硝酸浸铅锌矿尾渣回收银工艺进行了研究.以银浸出率为评价指标,探讨了硝酸质量浓度、液固比、浸出时间和浸出温度对回收银工艺的影响.在单因素实验的基础上,利用响应面法对银浸出的条件进行了优化.结果表明,当硝酸质量浓度为33.16%,液固比为16.39:1,在64.62℃的条件下浸出1.3h,该模型预测的最大银浸出率为69.73%.验证实验误差<3%,表明该模型与实际情况拟合良好.%The extraction process using nitric acid leaching silver from lead-zinc mine tail slag was studied. According to silver leaching rate using as an evaluation index, the effect of nitric acid mass concentration, the liquid-solid ratio,leaching time and leaching temperature on silver leaching rate was discussed. Based on single factor experiment, the leaching condition is further optimized by response surface method. The results showed that the largest model silver leaching rate of 69. 73% was obtained under the conditions of the concentration of 33.16% nitric acid quality and the liquid-solid ratio of 16.39:1 at 64.62 ℃ for 1.3 h. The verify error of the model was less than 3% ,and the model was fitted for the actual experiments well.

  3. 硝酸装置铂网中毒事故原因分析及解决措施%Cause Analysis of Poisoning Accident of Platinum Net in Nitric Acid Plant and Its Solution Measure

    Institute of Scientific and Technical Information of China (English)

    潘利新

    2014-01-01

    In allusion to that a relatively serious poisoning accident of platinum net existed in the nitric acid section of ammonium nitrate plant in Hei-longjiang Chemical Engineering Group Corporation, the reason of accident was analyzed and the appropriate solution measure was briefly described.%针对黑化集团硝铵厂硝酸工段一次较为严重的铂网中毒事故,分析了事故原因,简述了相应的解决措施。

  4. 利用硝酸回收机械化学活化后的硫化物浓缩液中的铅%Recovery of Lead from Sulfide Concentrate after Mechanochemical Activation Using Nitric Acid

    Institute of Scientific and Technical Information of China (English)

    A.G. Kholmogorov; O.N. Kononova; G.L. Pashkov; L.V. Shashina; V.P. Plekhanov; A.A. Sabetskiy

    2005-01-01

    Decomposition of lead sulfide concentrates in nitric acidic solutions after ferric (Ⅲ) nitrate addition and mechanical preparation has been investigated. It was found out that the decomposition can be achieved in of mechanochemical activation. The use of [Fe(NO3)3-HNO3-H2O] aqueous salt system allows the decomposition of lead sulfide concentrate at room temperature and in this case the concentration of HNO3 does not exceed mechanochemical activation of this concentrate. The insoluble residues after the leaching contain SiO2, S0, FeCO3 and PbSO4.

  5. Co-extraction and co-stripping of U(VI) and Pu(IV) using tri-iso-amyl phosphate and tri-n-butyl phosphate in n-dodecane from nitric acid media under high loading conditions

    Energy Technology Data Exchange (ETDEWEB)

    Sreenivasulu, Balija; Suresh, Ammath; Sivaraman, Nagarajan; Rao, P.R. Vasudeva [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Chemistry Group

    2016-08-01

    The extraction of Pu(IV) using 1.1 M solution of tri-iso-amyl phosphate (TiAP)/n-dodecane (DD) from plutonium nitrate solutions in nitric acid media was examined as a function of equilibrium aqueous phase metal ion concentration and equilibrium aqueous phase acidity at 303 K. The nitric acid concentration in the organic phase was measured as a function of equilibrium organic phase plutonium concentration. The co-extraction of U(VI) and Pu(IV) was studied using 1.1 M TiAP/DD system as a function of their equilibrium aqueous phase metal ion concentration and compared with 1.1 M tri-n-butyl phosphate (TBP)/n-DD system under identical conditions. Co-extraction and co-stripping of U(VI) and Pu(IV) were studied using 1.1 M TiAP/DD and 1.1 M TBP/DD systems in cross current mode to evaluate the number of stages required for the extraction and stripping of heavy metal ions (uranium and plutonium). The extraction and stripping efficiencies were calculated for both the systems. The saturation limit of the organic phase was also established in these studies.

  6. Boiling Heat Transfer to Halogenated Hydrocarbon Refrigerants

    Science.gov (United States)

    Yoshida, Suguru; Fujita, Yasunobu

    The current state of knowledge on heat transfer to boiling refrigerants (halogenated hydrocarbons) in a pool and flowing inside a horizontal tube is reviewed with an emphasis on information relevant to the design of refrigerant evaporators, and some recommendations are made for future research. The review covers two-phase flow pattern, heat transfer characteristics, correlation of heat transfer coefficient, influence of oil, heat transfer augmentation, boiling from tube-bundle, influence of return bend, burnout heat flux, film boiling, dryout and post-dryout heat transfer.

  7. Microlayer during boiling in narrow slot channels

    Science.gov (United States)

    Diev, Mikhail D.; Leontiev, Alexander I.

    1997-01-01

    An international space station Alpha will have a two-phase thermal control system. Boiling of a liquid ammonia will be a process of heat collection in evaporative heat exchangers. Unfortunately, only little data is available for boiling heat transfer in microgravity. Geometries of boiling channels working good in normal gravity are not appropriate in microgravity, and special means should be worked out to avoid some undesired events. From this point of view, the narrow slot channels may be assumed as a promising geometry for microgravity operation. During boiling in narrow slots, the vapor bubbles are flattened between the channel walls. The vapor phase and the channel wall are separated by a thin liquid film which is known as a microlayer. The paper presents the experimental results compared to the theoretical analysis, the paper also shows the narrow slot channels as a perspective configuration for microgravity applications.

  8. Absorption of nitric oxide into aqueous solutions of ferrous chelates accompanied by instantaneous reaction

    NARCIS (Netherlands)

    Demmink, J.F; vanGils, I.C.F.; Beenackers, A.A C M

    1997-01-01

    The absorption of nitric oxide (NO) into aqueous solutions of ferrous chelates of nitrilotriacetic acid (NTA), ethylene diaminetetraacetic acid (EDTA), hydroxyethylenediaminetriacetic acid (HEDTA), and diethylenetriaminepentaacetic acid (DTPA) was studied in a stirred cell reactor. Experimental cond

  9. Opposing effects of D-aspartic acid and nitric oxide on tuning of testosterone production in mallard testis during the reproductive cycle

    Directory of Open Access Journals (Sweden)

    Assisi Loredana

    2008-07-01

    Full Text Available Abstract Background D-Aspartic acid (D-Asp and nitric oxide (NO play an important role in tuning testosterone production in the gonads of male vertebrates. In particular, D-Asp promotes either the synthesis or the release of testosterone, whereas NO inhibits it. In this study, we have investigated for the first time in birds the putative effects of D-Asp and NO on testicular testosterone production in relation to two phases of the reproductive cycle of the adult captive wild-strain mallard (Anas platyrhynchos drake. It is a typical seasonal breeder and its cycle consists of a short reproductive period (RP in the spring (April-May and a non reproductive period (NRP in the summer (July, a time when the gonads are quiescent. The presence and the localization of D-Asp and NO in the testis and the trends of D-Asp, NO and testosterone levels were assessed during the main phases of the bird's reproductive cycle. Furthermore, in vitro experiments revealed the direct effect of exogenously administered D-Asp and NO on testosterone steroidogenesis. Methods By using immunohistochemical (IHC techniques, we studied the presence and the distributional pattern of D-Asp and NO in the testes of RP and NRP drakes. D-Asp levels were evaluated by an enzymatic method, whereas NO content, via nitrite, was assessed using biochemical measurements. Finally, immunoenzymatic techniques determined testicular testosterone levels. Results IHC analyses revealed the presence of D-Asp and NO in Leydig cells. The distributional pattern of both molecules was in some way correlated to the steroidogenic pathway, which is involved in autocrine testosterone production. Indeed, whereas NO was present only during the NRP, D-Asp was almost exclusively present during the RP. Consistently, the high testosterone testicular content occurring during RP was coupled to a high D-Asp level and a low NO content in the gonad. By contrast, in sexually inactive drakes (NRP, the low testosterone

  10. Effect of gamma-aminobutyric acid B receptor on nitric oxide/nitric oxide synthase system during recurrent febrile seizures%反复热性惊厥过程中γ-氨基丁酸B受体对一氧化氮/一氧化氮合酶体系的调节作用

    Institute of Scientific and Technical Information of China (English)

    韩颖; 秦炯; 卜定方; 杨志仙; 常杏芝; 杜军保

    2006-01-01

    目的:探讨γ-氨基丁酸B受体(γ-aminobutyric acid B receptor,GABABR)对热性惊厥(febrile seizure,FS)大鼠一氧化氮(nitric oxide,NO)/一氧化氮合酶(nitric oxide synthase,NOS)体系表达的影响.方法:将21 d龄SD大鼠随机分为对照组、FS组、FS+巴氯芬(baclofen)组和FS+法克罗芬(phaclofen)组.采用热水浴诱导大鼠FS,隔日诱导1次,共10次.采用分光光度计法测定大鼠血浆中NO含量;用原位杂交方法观察神经元型一氧化氮合酶(neuronal nitric oxide synthase,nNOS)mRNA表达情况;用免疫组化方法观察nNOS蛋白表达情况.结果:FS+baclofen组NO含量低于FS组[(19.02±9.31)μmol/L比(40.03±9.12)μmol/L],同时nNOS蛋白和mRNA表达也较FS组减弱;而FS+phaclofen组NO含量高于FS组[(66.46±8.15)μmol/L比(40.03±9.12)μmol/L],同时nNOS蛋白和mRNA表达也较FS组增强.结论:反复热性惊厥过程中,GABABR的改变可影响NO/NOS体系的表达.

  11. The investigation of boiling crisis of nanofluids

    Directory of Open Access Journals (Sweden)

    Minakov Andrey

    2016-01-01

    Full Text Available Saturated boiling of nanofluids on a cylindrical heater with different diameters is experimentally studied. Studied nanofluids were prepared using distilled water and different metal oxides nanoparticles. The volume concentration of the nanoparticles was changed from 0.05 to 1%. It has been measured that the critical heat flux for nanofluids was much higher than for water. A strong dependence of CHF on the material and size of the nanoparticles and duration of boiling and size of heater was shown.

  12. Using Boiling for Treating Waste Activated Sludge

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In this work we investigated the feasibility of using short time, low superheat boiling to treat biological sludge. The treated sludge exhibited reduced filterability and enhanced settleability. The boiling treatment released a large amount of extra-cellular polymers (ECPs) from the solid phase and reduced the microbial density levels of the total coliform bacteria and the heterotrophic bacteria. A diluted sludge is preferable for its high degree of organic hydrolysis and sufficient reduction in microbial density levels.

  13. How To Boil the Perfect Egg

    Institute of Scientific and Technical Information of China (English)

    小雨

    2007-01-01

    A British inventor says he has cracked(破解)the age-old riddle(难题)of how to boil the perfect egg,get rid of(摆脱)the water. Simon Rhymes uses powerful light bulbs instead of boiling water to cook the egg. The gadget(小发明)does the job in six minutes,and then chons off(削)the top of

  14. High flux film and transition boiling

    Science.gov (United States)

    Witte, L. C.

    1993-02-01

    An investigation was conducted on the potential for altering the boiling curve through effects of high velocity and high subcooling. Experiments using water and Freon-113 flowing over cylindrical electrical heaters in crossflow were made to see how velocity and subcooling affect the boiling curve, especially the film and transition boiling regions. We sought subcooling levels down to near the freezing points of these two liquids to prove the concept that the critical heat flux and the minimum heat flux could be brought together, thereby averting the transition region altogether. Another emphasis was to gain insight into how the various boiling regions could be represented mathematically on various parts of the heating surface. Motivation for the research grew out of a realization that the effects of very high subcooling and velocity might be to avert the transition boiling altogether so that the unstable part of the boiling curve would not limit the application of high flux devices to temperatures less than the burnout temperatures. Summaries of results from the study are described. It shows that the potential for averting the transition region is good and points the way to further research that is needed to demonstrate the potential.

  15. 硝酸装置铂网中毒的处理及预防措施%Treatment and Precautionary Measures of Platinum Gauze Poisoning in Nitric Acid Unit

    Institute of Scientific and Technical Information of China (English)

    刘多恩

    2014-01-01

    The dual-pressure dilute nitric acid production process flow sheet and affected location of platinum gauze poisoning are introduced, process conditions and causes for platinum gauze iron poisoning, oil poisoning and ash poisoning are analyzed.In connection with platinum gauze poisoning happened in nitric acid unit, relevant precautionary measures are proposed, i.e., improvement of purification degree of air filter, addition of ammonia filter or update ammonia filter type, and reduction of iron impurities sources.%介绍了双加压法稀硝酸生产工艺流程及铂网中毒后的影响部位,分析了铂网铁中毒、油中毒和灰中毒的工艺状况及原因。针对硝酸装置出现过的铂网中毒现象,提出了相应的预防措施,即提高空气过滤器的净化度、增设氨过滤器或更新氨过滤器型式、减少铁杂质的来源。

  16. Heterogeneous uptake of gaseous nitric acid on dolomite (CaMg(CO3)2) and calcite (CaCO3) particles: a Knudsen cell study using multiple, single, and fractional particle layers.

    Science.gov (United States)

    Johnson, Elizabeth R; Sciegienka, Joanna; Carlos-Cuellar, Sofia; Grassian, Vicki H

    2005-08-11

    In this study, the heterogeneous uptake of gaseous nitric acid on dolomite, CaMg(CO3)2, and calcite, CaCO3, particles under dry conditions at 296 K was investigated. A Knudsen cell reactor was used to measure heterogeneous uptake coefficients for these reactions. Several different experiments were performed including those on many, single, and fractional layers of particles. For experiments using multiple particle layers, the Knudsen cell data were modeled to take into account gas diffusion into the underlying layers of the sample. From this analysis, initial heterogeneous uptake coefficients, gamma(o,t), were determined to be (5 +/- 2) x 10(-4) and (2 +/- 1) x 10(-3), for dolomite and calcite, respectively, at a nitric acid concentration of 6.5 x 10(10) molecules cm(-3). For experiments that employed single or fractional particle layers, the initial heterogeneous uptake coefficient was analyzed using a recent method described in the literature. Values of the initial heterogeneous uptake coefficient using this analysis were in agreement with the above analysis and determined to be (7 +/- 4) x 10(-4) and (2 +/- 0.4) x 10(-3) for CaMg(CO3)2 and CaCO3, respectively. In addition, these results are compared to previous literature values.

  17. Flow boiling heat transfer in circulating fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Xiaoguang REN; Jiangdong ZHENG; Sefiane KHELLII; Arumemi-Ikhide MICHAEL

    2009-01-01

    In order to enhance heat transfer and mitigate contamination in the boiling processes, a new type of vapor-liquid-solid (3-phase) circulating fluidized bed boil-ing system has been designed, combining a circulating fluidized bed with boiling heat transfer. Experimental results show an enhancement of the boiling curve. Flow visualization studies concerning flow hydrodynamics within the riser column are also conducted whose results are presented and discussed.

  18. Surface boiling of superheated liquid

    Energy Technology Data Exchange (ETDEWEB)

    Reinke, P. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-01-01

    A basic vaporization mechanism that possibly affects the qualitative and quantitative prediction of the consequences of accidental releases of hazardous superheated liquids was experimentally and analytically investigated. The studies are of relevance for the instantaneous failure of a containment vessel filled with liquefied gas. Even though catastrophical vessel failure is a rare event, it is considered to be a major technological hazard. Modeling the initial phase of depressurisation and vaporization of the contents is an essential step for the subsequent analysis of the spread and dispersion of the materials liberated. There is only limited understanding of this inertial expansion stage of the superheated liquid, before gravity and atmospheric turbulence begin to dominate the expansion. This work aims at a better understanding of the vaporization process and to supply more precise source-term data. It is also intended to provide knowledge for the prediction of the behavior of large-scale releases by the investigation of boiling on a small scale. Release experiments with butane, propane, R-134a and water were conducted. The vaporization of liquids that became superheated by sudden depressurisation was studied in nucleation-site-free glass receptacles. Several novel techniques for preventing undesired nucleation and for opening the test-section were developed. Releases from pipes and from a cylindrical geometry allowed both linear one-dimensional, and radial-front two-dimensional propagation to be investigated. Releases were made to atmospheric pressure over a range of superheats. It was found that, above a certain superheat temperature, the free surface of the metastable liquid rapidly broke up and ejected a high-velocity vapor/liquid stream. The zone of intense vaporization and liquid fragmentation proceeded as a front that advanced into the test fluids. No nucleation of bubbles in the bulk of the superheated liquid was observed. (author) figs., tabs., refs.

  19. The electrochemical aspect of the corrosion of austenitic stainless steels, in nitric acid and in the presence of hexavalent chromium (1961); Aspect electrochimique de la corrosion d'aciers inoxydables austenitiques en milieu nitrique et en presence de chrome hexavalent (1961)

    Energy Technology Data Exchange (ETDEWEB)

    Coriou, H.; Hure, J.; Plante, G. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1961-07-01

    The corrosion of austenitic stainless steels in boiling nitric acid markedly increases when the medium contains hexavalent chromium ions. Because of several redox phenomena, the potential of the steel generally changes in course of time. Measurements show a relation between the weight loss and the potential of specimens. Additions of Mn(VII) and Ce(IV) are compared with that of Cr(VI), and show that the relation is a general one. The attack cf the metal in oxidizing media is largely intergranular, leading to exfoliation of the grains, although the steel studied is not sensitive to the classical Huey and Strauss tests. Also even in the absence of any other oxidizing reaction, the current density observed when the steel is anodically polarized under potentiostatic conditions does not correspond to the actual weight loss of the metal. (authors) [French] La corrosion d'aciers inoxydables austenitiques en milieu nitrique bouillant augmente notablement quand le milieu contient des ions chrome a l'etat hexavalent. Par suite de divers phenomenes d'oxydo-reduction, le potentiel de l'acier evolue generalement au cours du temps. Les mesures effectuees permettent d'etablir une relation entre les pertes de poids et le potentiel des echantillons. L'addition de Mn(VI) et Ce(IV) est compare a celle de Cr(VI) et montre que la relation precedente s'applique de facon generale. L'attaque du metal en milieu oxydant est en grande, partie due a une corrosion intergranulaire conduisant a un dechaussement des grains bien que l'acier etudie ne soit pas sensible aux tests classiques de Huey et de Strauss. Aussi, meme en l'absence de toute autre reaction d'oxydation l'intensite qu l'on observerait en soumettant l'acier a un potentiel anodique dans un montage potentiostatique ne correspondrait pas a la perte de poids reelle du metal. (auteurs)

  20. Cryogenic Boil-Off Reduction System

    Science.gov (United States)

    Plachta, David W.; Guzik, Monica C.

    2014-03-01

    A computational model of the cryogenic boil-off reduction system being developed by NASA as part of the Cryogenic Propellant Storage and Transfer technology maturation project has been applied to a range of propellant storage tanks sizes for high-performing in-space cryogenic propulsion applications. This effort focuses on the scaling of multi-layer insulation (MLI), cryocoolers, broad area cooling shields, radiators, solar arrays, and tanks for liquid hydrogen propellant storage tanks ranging from 2 to 10 m in diameter. Component scaling equations were incorporated into the Cryogenic Analysis Tool, a spreadsheet-based tool used to perform system-level parametric studies. The primary addition to the evolution of this updated tool is the integration of a scaling method for reverse turbo-Brayton cycle cryocoolers, as well as the development and inclusion of Self-Supporting Multi-Layer Insulation. Mass, power, and sizing relationships are traded parametrically to establish the appropriate loiter period beyond which this boil-off reduction system application reduces mass. The projected benefit compares passive thermal control to active thermal control, where active thermal control is evaluated for reduced boil-off with a 90 K shield, zero boil-off with a single heat interception stage at the tank wall, and zero boil-off with a second interception stage at a 90 K shield. Parametric studies show a benefit over passive storage at loiter durations under one month, in addition to showing a benefit for two-stage zero boil-off in terms of reducing power and mass as compared to single stage zero boil-off. Furthermore, active cooling reduces the effect of varied multi-layer insulation performance, which, historically, has been shown to be significant.

  1. Lattice Boltzmann modeling of boiling heat transfer: The boiling curve and the effects of wettability

    CERN Document Server

    Li, Q; Francois, M M; He, Y L; Luo, K H

    2015-01-01

    A hybrid thermal lattice Boltzmann (LB) model is presented to simulate thermal multiphase flows with phase change based on an improved pseudopotential LB approach [Q. Li, K. H. Luo, and X. J. Li, Phys. Rev. E 87, 053301 (2013)]. The present model does not suffer from the spurious term caused by the forcing-term effect, which was encountered in some previous thermal LB models for liquid-vapor phase change. Using the model, the liquid-vapor boiling process is simulated. The boiling curve together with the three boiling stages (nucleate boiling, transition boiling, and film boiling) is numerically reproduced in the LB community for the first time. The numerical results show that the basic features and the fundamental characteristics of boiling heat transfer are well captured, such as the severe fluctuation of transient heat flux in the transition boiling and the feature that the maximum heat transfer coefficient lies at a lower wall superheat than that of the maximum heat flux. Furthermore, the effects of the he...

  2. Useful and harmful effects of nitric oxide

    Directory of Open Access Journals (Sweden)

    Jović Slavoljub

    2013-01-01

    Full Text Available In living sistems synthesis of nitric oxide occurs during metabolism from Larginin, nitrite and ascorbate. Being very significant carrier of information within numerous both physiological and pathological proceses in mammals' organisms, nitric oxid could possibly be useful as well as harmful. Nitric oxide synthesis is adjuvant in a healthy organism because it represents the basic molecule for understanding numerous processes in neurology, psychology, immunology and varios related fields. In other words, nitric oxide participate in number of physiological processes, such as: transmission of nerve signals (neurotransmitter role, regulation of smooth muscle tissue relaxation (eg. vasodilatation, peristaltic movements, immunomodulation, mastocyte activation, development of inflammatory response, apoptosis regulation, angiogenesis and glucose metabolism, normal heart functioning and antioxidation role. Besides being useful, nitric oxide can be harmful as well, because it has one unpaired electron, so consequently it is susceptible to oxidation becoming a stable free radical. Being such, it reacts quickly with superoxide-anion radical, givind at first an extremely reactive peroxinitrite anion, and subsequently peroxidnitrite acid. This acid is very dangerous causing thiol groups oxidation, tyrosine and phenylalanine nitrosylation, lipid oxidation, DNK chain splitting, nitrification and nucleic bases deamination. These damages of macromolecules can cause a series of undesirable changes which subsequently distub functions of molecules, and thus of cells, tissues and even organs. [Projekat Ministarstva nauke Republike Srbije, br. 173034 i br. 31085

  3. Palmitic acid exerts pro-inflammatory effects on vascular smooth muscle cells by inducing the expression of C-reactive protein, inducible nitric oxide synthase and tumor necrosis factor-α.

    Science.gov (United States)

    Wu, Di; Liu, Juntian; Pang, Xiaoming; Wang, Shuyue; Zhao, Jingjing; Zhang, Xiaolu; Feng, Liuxin

    2014-12-01

    Atherosclerosis is a chronic inflammatory disease in the vessel, and inflammatory cytokines play an important role in the inflammatory process of atherosclerosis. A high level of free fatty acids (FFAs) produced in lipid metabolism disorders are known to participate in the formation of atherosclerosis through multiple bioactivities. As the main saturated fatty acid in FFAs, palmitic acid stimulates the expression of inflammatory cytokines in macrophages. However, it is unclear whether palmitic acid exerts a pro-inflammatory effect on vascular smooth muscle cells (VSMCs). The purpose of the present study was to observe the effect of palmitic acid on the expression of C-reactive protein (CRP), tumor necrosis factor α (TNF-α) and inducible nitric oxide synthase (iNOS) in VSMCs. Rat VSMCs were cultured, and palmitic acid was used as a stimulant for CRP, TNF-α and iNOS expression. mRNA expression was assayed with reverse transcription-polymerase chain reaction, and protein expression was detected with western blot analysis and immunocytochemistry. The results showed that palmitic acid significantly stimulated mRNA and protein expression of CRP, TNF-α and iNOS in VSMCs in time- and concentration-dependent manners, and therefore, palmitic acid is able to exert a pro-inflammatory effect on VSMCs via stimulating CRP, TNF-α and iNOS expression. The findings provide a novel explanation for the direct pro-inflammatory and atherogenic effects of palmitic acid, and for the association with metabolic syndrome, such as type 2 diabetes mellitus, obesity and atherosclerosis. Therefore, the intervention with anti-inflammatory agents may effectively delay the formation and progression of atherosclerosis in patients with metabolic syndrome.

  4. A review of film boiling at cryogenic temperatures.

    Science.gov (United States)

    Hsu, Y. Y.

    1972-01-01

    Film boiling occurs in the quenching of metals, the chilling of biological species, the regenerative cooling of rockets, and the cooling down of a cryogenic fuel tank. Occasionally film boiling is also found in a nuclear reactor or in a cryomagnet. Aspects of film boiling involving an unconstrained liquid mass are considered, giving attention to the evaporation time, the Leidenfrost temperature, solid-liquid contacts, the thermal properties of the solid, effects of coating or scale, wettability, the metastable condition, and the velocity effect on drops. Developments discussed with regard to pool boiling are related to vertical surfaces, film boiling from horizontal surfaces, film boiling from a horizontal cylinder, film boiling from a sphere, and film boiling of helium. Processes of film boiling in a channel are also analyzed.

  5. Processes regulating nitric oxide emissions from soils

    DEFF Research Database (Denmark)

    Pilegaard, Kim

    2013-01-01

    Nitric oxide (NO) is a reactive gas that plays an important role in atmospheric chemistry by influencing the production and destruction of ozone and thereby the oxidizing capacity of the atmosphere. NO also contributes by its oxidation products to the formation of acid rain. The major sources...

  6. Nitric oxide supersensitivity

    DEFF Research Database (Denmark)

    Olesen, J; Iversen, Helle Klingenberg; Thomsen, L L

    1993-01-01

    in a double blind design to 17 migraine patients, 17 age and sex matched healthy controls and 9 subjects with tension-type headache. The nitroglycerin-induced headache was significantly more severe in migraine sufferers, lasted longer and fulfilled diagnostic criteria for migraine more often. We have...... previously shown a similar supersensitivity to histamine which in human cerebral arteries activates endothelial H1 receptors and causes endothelial production of nitric oxide. Migraine patients are thus supersensitive to exogenous nitric oxide from nitroglycerin as well as to endothelially produced nitric...

  7. The entropy balance for boiling flow

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco-Javier E-mail: fjk@posta.unizar.es

    2001-10-01

    Subcooled forced convection boiling of water is recognized as one of the best means of accommodating the very high heat fluxes that plasma facing components of fusion reactors have to withstand. The boiling curve, giving the wall temperature in function of the applied flux and flow conditions, is essential for the design of such cooling configurations. In this paper, a new entropy balance for subcooled boiling flow, which allows the wall temperature to be obtained, is presented and successfully compared with experimental data from the Joint US-EURATOM R and D Program. The derivation of this entropy balance is based on a new strict application of the Reynolds theorem to multiphase flows recently proposed by the author.

  8. Thermodynamics of Flow Boiling Heat Transfer

    Science.gov (United States)

    Collado, F. J.

    2003-05-01

    Convective boiling in sub-cooled water flowing through a heated channel is essential in many engineering applications where high heat flux needs to be accommodated. It has been customary to represent the heat transfer by the boiling curve, which shows the heat flux versus the wall-minus-saturation temperature difference. However it is a rather complicated problem, and recent revisions of two-phase flow and heat transfer note that calculated values of boiling heat transfer coefficients present many uncertainties. Quite recently, the author has shown that the average thermal gap in the heated channel (the wall temperature minus the average temperature of the coolant) was tightly connected with the thermodynamic efficiency of a theoretical reversible engine placed in this thermal gap. In this work, whereas this correlation is checked again with data taken by General Electric (task III) for water at high pressure, a possible connection between this wall efficiency and the reversible-work theorem is explored.

  9. 硝酸浸出失效催化剂提取银的实验研究%Experimental Study on Extracting Silver by Leaching Spent Catalyst with Nitric Acid

    Institute of Scientific and Technical Information of China (English)

    范兴祥; 董海刚; 吴跃东; 付光强; 刘杨; 赵家春; 吴晓峰; 昝林寒; 李博捷

    2013-01-01

    采用硝酸浸出失效催化剂提取其中金属银,研究了失效催化剂粒度、硝酸用量、浸出温度、浸出时间和洗涤次数等因素对银浸出率的影响.结果表明,失效催化剂粒度对银浸出率影响显著,增加洗涤次数有利于提高银的浸出率.通过实验,确定了合理的工艺参数为:硝酸用量为失效催化剂质量的70%、浸出温度65℃、浸出时间3h、催化剂粒度为0.125 ~0.18 mm、搅拌洗涤3次.在此条件下,银的浸出率为99.52%,浸出渣含银0.072%.综合实验结果表明,从失效催化剂到海绵银产品,银的直收率达到99.27%.%Spent catalyst was leached by nitric acid to extract metallic silver from it. The effects of the particle size of spent catalyst, the dosage of nitric acid, leaching temperature, leaching time and washing times on the leaching rate of silver were investigated. The results showed that the particle size of spent catalyst has great effect on the leaching rate of silver which would also be improved by increasing washing times. Based on experiments, technological parameters are reasonably determined as follows; the dosage of nitric acid was 70% of the quality of spent catalyst, the leaching temperature was set at 65 ℃, leaching time was 3 h, the particle size was 0.125 ~0.18 mm, the washing times were 3. Under these conditions, the leaching rate of silver was 99.52% and the content of silver in the leaching residues was 0.072%. The comprehensive experiment showed that spent catalyst can be transferred to sponge silver products with this process with direct recovery rate of silver reaching 99.27%.

  10. Removal of Methyl Orange from Aqueous Solution by Nitric Acid-Modified Titanium Ore%硝酸掺杂钛精矿吸附去除甲基橙

    Institute of Scientific and Technical Information of China (English)

    雷雪飞; 薛向欣; 杨合

    2012-01-01

    Nitric acid-modified titanium ore (NATO) sorbents were prepared by high energy ball milling process. The adsorption properties of NATO sorbents were evaluated by the decoloration efficiency of methyl orange (MO) under dark-state absorption. In the adsorption stage, L9(34) orthogonal experiments of different factors, for example, doping ratio, calcination temperature, soaking time and heating rate were performed. Based on the orthogonal experiments, the optimal operating parameters, 2.0wt % nitric acid, 300 ℃ calcination temperature, 3 h soaking time, and 10 ℃/min heating rate, are obtained. In this optimal condition, the decoloration efficiency of MO reaches 96.8 %, which is significantly better than the undoped samples. Thus, it is feasible to treat dye wastewater by these NATO sorbents.%采用高能球磨法制备了一系列硝酸掺杂的钛精矿(nitric acid-modified titanium ore,NATO)吸附材料,采用正交表L9(34)安排实验,以甲基橙(MO)溶液的脱色率作为衡量吸附剂优劣的重要判据.以硝酸掺杂比例、煅烧温度、保温时间、升温速率为因素进行正交试验,基于降低能耗和成本的考虑和综合分析的基础上,得到制备NATO吸附剂的最优工艺条件:硝酸掺杂比例为2.0%,煅烧温度为300℃,保温时间为3 h,升温速率为10℃/min.在较优工艺条件下制备的NATO吸附剂对甲基橙的脱色率达到96.8%,明显优于未掺杂样品,且沉降性能较好,易于分离,是一类有应用前景的吸附材料.

  11. Boiling on Microconfigured Composite Surfaces Enhanced

    Science.gov (United States)

    Chao, David F.

    2000-01-01

    Boiling heat transfer is one of the key technologies for the two-phase active thermal-control system used on space platforms, as well as for the dynamic power systems aboard the International Space Station. Because it is an effective heat transfer mode, boiling is integral to many space applications, such as heat exchangers and other cooling devices. Nucleate boiling near the critical heat flux (CHF) can transport very large thermal loads with a much smaller device and much lower pumping power than for single-phase heat exchangers. However, boiling performance sharply deteriorates in a reduced-gravity environment, and operation in the CHF regime is somewhat perilous because of the risk of burnout to the device surface. New materials called microconfigured metal-graphite composites can enhance boiling. The photomicrograph shows the microconfiguration (x3000) of the copper-graphite (Cu-Gr) surface as viewed by scanning electronic microscope. The graphite fiber tips appear as plateaus with rugged surfaces embedded in the copper matrix. It has been experimentally demonstrated that this type of material manifests excellent boiling heat transfer performance characteristics and an increased CHF. Nonisothermal surfaces were less sensitive to variations of wall superheat in the CHF regime. Because of the great difference in conductivity between the copper base and the graphite fiber, the composite surfaces have a nonisothermal surface characteristic and, therefore, will have a much larger "safe" operating region in the CHF regime. In addition, the thermocapillary forces induced by the temperature differences between the fiber tips and the metal matrix play an important role in bubble detachment, and may not be adversely affected in a reduced-gravity environment. All these factors indicate that microconfigured composites may improve the reliability and economy (dominant factors in all space applications) of various thermal components found on spacecraft during future

  12. An Investigation of Graduate Scientists' Understandings of Evaporation and Boiling.

    Science.gov (United States)

    Goodwin, Alan; Orlik, Yuri

    2000-01-01

    Uses a video presentation of six situations relating to the evaporation and boiling of liquids and the escape of dissolved gases from solution and investigates graduate scientists' understanding of the concepts of boiling and evaporation. (Author/YDS)

  13. 硝酸处理对竹炭曝气生物滤池性能的影响%The Influence of Nitric Acid Modification on Aerated Bio-filter with Bamboo Charcoal as Carriers

    Institute of Scientific and Technical Information of China (English)

    罗舒君

    2015-01-01

    以硝酸处理竹炭作为曝气生物滤池填料,通过研究硝酸处理对竹炭吸附性能、表面官能团等的影响,考查硝酸处理竹炭对反应器性能的影响.结果表明,硝酸处理后竹炭表面含氧官能团增加,有利于微生物的附着,仅4d就完成挂膜, 反应器对有机负荷具有良好的去除能力, 在COD负荷为1.8和4.8 kg/(m3·d) 时, 平均去除率分别为83.3%和79.4%.%In this study, the influence of nitric acid modification on the adsorption performance and the surface functional groups of the bamboo charcoal was investigated. After that, the modified bamboo charcoal was employed as the bio-filter for wastewater treatment to study its performance on dealing with organic matter. The results indicated that the nitric acid modification increased surface oxygen functional groups of bamboo charcoal. The modification also promoted the growing of the microorganism, and shortened the mature period of bio-film to 4 days. The reactor was good at COD treatment. On condition that COD volume loaded of system was 1.8 and 4.8 kg/(m3·d), the removal efficiency can reached to 83.3%and 79.4%, respectively.

  14. Heat transfer coefficient for boiling carbon dioxide

    DEFF Research Database (Denmark)

    Knudsen, Hans Jørgen Høgaard; Jensen, Per Henrik

    1998-01-01

    Heat transfer coefficient and pressure drop for boiling carbon dioxide (R744) flowing in a horizontal pipe has been measured. The calculated heat transfer coeeficient has been compared with the Chart correlation of Shah. The Chart Correlation predits too low heat transfer coefficient but the ratio...

  15. Heat transfer coeffcient for boiling carbon dioxide

    DEFF Research Database (Denmark)

    Knudsen, Hans Jørgen Høgaard; Jensen, Per Henrik

    1997-01-01

    Heat transfer coefficient and pressure drop for boiling carbon dioxide (R744) flowing in a horizontal pipe has been measured. The pipe is heated by condensing R22 outside the pipe. The heat input is supplied by an electrical heater wich evaporates the R22. With the heat flux assumed constant over...

  16. Electrically Driven Liquid Film Boiling Experiment

    Science.gov (United States)

    Didion, Jeffrey R.

    2016-01-01

    This presentation presents the science background and ground based results that form the basis of the Electrically Driven Liquid Film Boiling Experiment. This is an ISS experiment that is manifested for 2021. Objective: Characterize the effects of gravity on the interaction of electric and flow fields in the presence of phase change specifically pertaining to: a) The effects of microgravity on the electrically generated two-phase flow. b) The effects of microgravity on electrically driven liquid film boiling (includes extreme heat fluxes). Electro-wetting of the boiling section will repel the bubbles away from the heated surface in microgravity environment. Relevance/Impact: Provides phenomenological foundation for the development of electric field based two-phase thermal management systems leveraging EHD, permitting optimization of heat transfer surface area to volume ratios as well as achievement of high heat transfer coefficients thus resulting in system mass and volume savings. EHD replaces buoyancy or flow driven bubble removal from heated surface. Development Approach: Conduct preliminary experiments in low gravity and ground-based facilities to refine technique and obtain preliminary data for model development. ISS environment required to characterize electro-wetting effect on nucleate boiling and CHF in the absence of gravity. Will operate in the FIR - designed for autonomous operation.

  17. Cryogenic Propellant Boil-Off Reduction System

    Science.gov (United States)

    Plachta, D. W.; Christie, R. J.; Carlberg, E.; Feller, J. R.

    2008-03-01

    Lunar missions under consideration would benefit from incorporation of high specific impulse propellants such as LH2 and LO2, even with their accompanying boil-off losses necessary to maintain a steady tank pressure. This paper addresses a cryogenic propellant boil-off reduction system to minimize or eliminate boil-off. Concepts to do so were considered under the In-Space Cryogenic Propellant Depot Project. Specific to that was an investigation of cryocooler integration concepts for relatively large depot sized propellant tanks. One concept proved promising—it served to efficiently move heat to the cryocooler even over long distances via a compressed helium loop. The analyses and designs for this were incorporated into NASA Glenn Research Center's Cryogenic Analysis Tool. That design approach is explained and shown herein. Analysis shows that, when compared to passive only cryogenic storage, the boil-off reduction system begins to reduce system mass if durations are as low as 40 days for LH2, and 14 days for LO2. In addition, a method of cooling LH2 tanks is presented that precludes development issues associated with LH2 temperature cryocoolers.

  18. Contact Angle Effects in Boiling Heat Transfer

    OpenAIRE

    Urquiola, Erwin; Fujita, Yasunobu

    2002-01-01

    This paper reports boiling experiments with pure water and surfactant solutions of SDS on horizontal heating surface. The static contact angle, rather than the surface tension value, was found to be the leading factor for the results and probably its prev

  19. Bubble Behavior in Nucleate Boiling Experiment Aboard the Space Shuttle

    OpenAIRE

    Koeln, Justin P.; Boulware, Jeffrey C.; Ban, Heng

    2009-01-01

    Boiling dynamics in microgravity need to be better understood before heat transfer systems based on boiling mechanism can be developed for space applications. This paper presents the results of a nucleate boiling experiment aboard Space Shuttle Endeavor (STS- 108). The experiment utilized nickel-chromium resistance wire to boil water in microgravity, and the data was recorded with a CCD camera and six thermistors. This data was analyzed to determine the behavior of bubble formation, detachmen...

  20. Boiling heat transfer characteristics of fatty acid methyl ester(FAME)in falling film evaporator%脂肪酸甲酯降膜蒸发器沸腾传热性能

    Institute of Scientific and Technical Information of China (English)

    徐委托; 马晓建; 马力; 陈俊英; 杨闪; 张芬芬

    2016-01-01

    利用传统的多管排列式蒸发器对高黏度、易结垢的混合物进行蒸发,容易造成布液器堵塞,且结垢后的传热管难以清理。因此根据物料特性,本文设计了一种新型的降膜蒸发器,采用大降液孔加倾斜环板进行布膜,利用内径较大的锥筒作为传热壁面,并以粗甲酯作为试验工质对蒸发器的降膜蒸发传热系数随蒸发器筒体半锥度角、液膜流动雷诺数以及输入热通量之间的关系进行了试验研究。结果表明:该型蒸发器对于上述工质具有较好的适用性,蒸发系统能够在保持较高的传热系数的条件下,连续运行而不发生堵塞;蒸发器筒体锥度角有效地强化了降膜蒸发传热过程,而较大的热通量及进料流量在一定程度上却不利于蒸发传热。最后建立了降膜蒸发传热系数随蒸发器筒体半锥角和流动准数之间的经验关联式。%Using conventional line-tube heat exchanger for evaporation of high viscosity and easy-to-scaling mixture can easily block liquid distributor and make the cleaning of foul tube impossible. Therefore,a new type of falling film evaporator was designed,which used large liquid orifice plus tilt ring plate for liquid distribution and took larger diameter of conical shell as heat transfer wall. The variation of boiling heat transfer coefficients with shell’s taper angle,Reynolds number and heat fluxes were determined by a pilot scale falling film evaporation system,using the FAME mixture as liquid model. Result showed that this type of evaporator worked well for FAME,the system could work smoothly with high heat transfer efficiency for a long time and without the occurrence of clogging. The evaporator shell’s taper angle can intensify heat transfer process. The increase of heat flux and feed flow had a negative influence on heat transfer coefficient. Experimental correlation for boiling heat transfer coefficients with consideration of

  1. The law of stable equilibrium and the entropy-based boiling curve for flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Collado, F.J. [Universidad de Zaragoza (Spain). Dpto. Ingenieria Mecanica Motores Termicos

    2005-05-01

    Convective flow boiling in sub-cooled fluids is recognized as one of the few means of accommodating very high heat fluxes. There are many available correlations for predicting the inner wall temperature of the heated duct in the several regimes of the empirical Nukiyama boiling curve, although unfortunately there is no physical fundamentals of such curve. Recently, the author has shown that the classical entropy balance could contain key information about boiling heat transfer. So, it was found that the average thermal gap in the heated channel (the inner wall temperature minus the average temperature of the coolant fluid) was strongly correlated with the efficiency of a theoretical reversible engine placed in this thermal gap. From this new correlation, a new boiling curve plotting the wall temperature versus the average fluid temperature was derived and successfully checked against low- and high-pressure water data. This curve suggested a new and simple definition of the critical heat flux (CHF) namely, the value of the coolant average temperature at the maximum. In this work, after briefly reviewing the entropy balance of a non-equilibrium boiling flow and its relationship with the thermodynamic average temperature and the law of stable equilibrium (LSE), the possibilities of the new approach for the design of flow boiling cooling systems are highlighted. Finally, the strong correlation found between the reversible engine efficiency and the thermal driving force is verified again, now with high-pressure refrigerant 22 (R-22) data. (author)

  2. Anti-obesity effects of boiled tuna extract in mice with obesity induced by a high-fat diet.

    Science.gov (United States)

    Kim, Youngmin; Kwon, Mi-Jin; Choi, Jeong-Wook; Lee, Min-Kyeong; Kim, Chorong; Jung, Jaehun; Aprianita, Heny; Nam, Heesop; Nam, Taek-Jeong

    2016-10-01

    The aim of this study was to examine the anti-obesity effects of boiled tuna extract in C57BL/6N mice with obesity induced by a high-fat diet (HFD). We determined the anti-obesity effects of boiled tuna extract (100, 200, or 400 mg/kg) on the progression of HFD-induced obesity for 10 weeks. The mice were divided into 5 groups as follows: the normal diet (ND) group (n=10); the HFD group (n=10); the mice fed HFD and 100 mg/kg boiled tuna extract group (n=10); those fed a HFD and 200 mg/kg boiled tuna extract group (n=10); and those fed a HFD and 400 mg/kg boiled tuna extract group (n=10). Changes in body weight, fat content, serum lipid levels and lipogenic enzyme levels were measured. The consumption of boiled tuna extract lowered epididymal tissue weight and exerted anti-obesity effects, as reflected by the serum glucose, triglyceride (TG), total cholesterol (TC), high-density lipoprotein cholesterol (HDL‑C), low-density lipoprotein cholesterol (LDL-C), insulin and leptin levels. In addition, we demonstrated changes in liver adipogenic- and lipogenic-related protein expression by western blot analysis. Boiled tuna extract downregulated the levels of the CCAAT/enhancer-binding protein α, β and δ (C/EBPα, β, δ), and peroxisome proliferator-activated receptor-γ (PPAR-γ) adipocyte marker genes. Boiled tuna extract also attenuated adipogenic and lipogenic gene expression, namely the levels of fatty acid synthase (FAS), lipoprotein lipase (LPL), acetyl-CoA carboxylase (ACC), glucose transporter type 4 (Glut4) and phosphorylated adenosine monophosphate-activated protein kinase α and β (AMPKα, β) in a dose-dependent manner. Moreover, the consumption of boiled tuna extract restored the levels of superoxide dismutase (SOD), catalase (CAT), glutamic oxaloacetic transaminase (GOT), glutamic-pyruvate transaminase (GPT), aspartate transaminase (AST) and alanine transaminase (ALT) to those of the control group. These results

  3. Thermohydrodynamics of boiling in a van der Waals fluid.

    Science.gov (United States)

    Laurila, T; Carlson, A; Do-Quang, M; Ala-Nissila, T; Amberg, G

    2012-02-01

    We present a modeling approach that enables numerical simulations of a boiling Van der Waals fluid based on the diffuse interface description. A boundary condition is implemented that allows in and out flux of mass at constant external pressure. In addition, a boundary condition for controlled wetting properties of the boiling surface is also proposed. We present isothermal verification cases for each element of our modeling approach. By using these two boundary conditions we are able to numerically access a system that contains the essential physics of the boiling process at microscopic scales. Evolution of bubbles under film boiling and nucleate boiling conditions are observed by varying boiling surface wettability. We observe flow patters around the three-phase contact line where the phase change is greatest. For a hydrophilic boiling surface, a complex flow pattern consistent with vapor recoil theory is observed.

  4. Comparison of material properties of polyethylene design types and design type tests of dangerous goods packaging depending on the prestorage time with 55% nitric acid; Vergleich der Materialeigenschaften von Polyethylenformstoffen und der Baumusterpruefungen von Gefahrgutverpackungen in Abhaengigkeit von der Vorlagerungsdauer mit 55%-iger Salpetersaeure

    Energy Technology Data Exchange (ETDEWEB)

    Weltschev, Margit; Niebergall, Ute; Haufe, Manuela; Heyer, Martina

    2010-12-22

    The material parameters melt flow rate MFR, density D, notched impact strength NIS at -30 C, stress crack resistance FNCT and resistance to oxidative degradation Ox (determined by the increase of MFR) have been selected for a comparison of the polyethylene grades for one design type in the ''European standard EN 15507: 2009 - Transport packaging for dangerous goods - Comparative material testing of polyethylene grades''. The parameters have a systematic relationship with design type tests. The notched impact strength at -30 C and the resistance to oxidative degradation of the polyethylene grades determined with test specimens of compression moulded sheets are directly comparable with drop tests at -18 C of design types produced of these grades. The design types were pre-stored with the standard liquid 55 % nitric acid for 21 days at 40 C. Tests in the dissertation: a comparison of the material parameters of high-density polyethylene grades with the behaviour of design types for the transport of dangerous goods showed that the marginal drop heights of some design types increased after pre-storage with 55 % nitric acid for 21 days rather than decreased. The effects of the marginal drop heights in drop tests at -18 C, the MFR and the tensile properties tensile strength, breaking elongation and the elastic modulus of the pre-storage time with 55 % nitric acid at 40 C and 23 C were investigated to verify and extend these test results. Packaging design types (jerricans) made of three polyethylene grades from different producers were pre-stored with 55 % nitric acid for 21, 42 and 84 days at 40 C as well as for six months at 23 C. The MFR and tensile properties of jerrican cuttings as well as the marginal drop heights of the jerricans in drop tests at -18 C were determined. The values of the notched impact strength at -30 C of the polyethylene grades are not comparable with the marginal drop heights determined in drop tests at -18 C. The marginal drop

  5. Effects of boiling and in vitro gastrointestinal digestion on the antioxidant activity of Sonchus oleraceus leaves.

    Science.gov (United States)

    Mawalagedera, S M M R; Ou, Zong-Quan; McDowell, Arlene; Gould, Kevin S

    2016-03-01

    Leaves of Sonchus oleraceus L. are especially rich in phenolic compounds and have potent extractable antioxidants. However, it is not known how their antioxidant activity changes after cooking and gastrointestinal digestion. We recorded the profile of phenolics and their associated antioxidant activity in both raw and boiled S. oleraceus leaf extracts after in vitro gastric and intestinal digestion, and quantified their antioxidant potentials using Caco-2 and HepG2 cells. Boiling significantly diminished the oxygen radical absorbance capacity (ORAC) and concentrations of ascorbate and chicoric acid in the soluble fractions. In contrast, 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging and concentrations of caftaric and chlorogenic acids were unaffected. Phenolics in the soluble fraction were absorbed into cultured human cells and exerted antioxidant activity. Only chlorogenic acid content remained stable during gastrointestinal digestion. S. oleraceus appears to be an excellent dietary source of phenolic antioxidants.

  6. Salvianolic Acid A Inhibits PDGF-BB Induced Vascular Smooth Muscle Cell Migration and Proliferation While Does Not Constrain Endothelial Cell Proliferation and Nitric Oxide Biosynthesis

    Directory of Open Access Journals (Sweden)

    Chao Huang

    2012-03-01

    Full Text Available Proliferation and migration of vascular smooth muscle cells (VSMCs are critical events in the initiation and development of restenosis upon percutaneous transluminal coronary angioplasty (PTCA. Polyphenols have been suggested to ameliorate post-angioplasty restenosis. Salvianolic A (SalA is one of the most abundant polyphenols extracted from salvia. In this study, we investigated the effect of salvianolic A (SalA on the migration and proliferation of VSMCs. We found a preferential interaction of SalA with cellular systems that rely on the PDGF signal, but not on the EGF and bFGF signal. SalA inhibits PDGF-BB induced VSMC proliferation and migration in the concentration range from 0.01 to 0.1 μM. The inhibition of SalA on VSMC proliferation is associated with cell cycle arrest. We also found that SalA inhibits the PDGFRβ-ERK1/2 signaling cascade activated by PDGF-BB in VSMCs. In addition, SalA does not influence the proliferation of endothelial cells, the synthesis of NO and eNOS protein expression. Our results suggest that SalA inhibits migration and proliferation of VSMCs induced by PDGF-BB via the inhibition of the PDGFRβ-ERK1/2 cascade, but that it does not constrain endothelial cell proliferation and nitric oxide biosynthesis. Thus, the present study suggests a novel adjunct pharmacological strategy to prevent angioplasty-related restenosis.

  7. Extraction of uranium (VI) from nitric acidwith N-decanoylpyrrolidine (DPOD) in toluene

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The extraction behaviors of uranium (VI) from nitric acid by N-decanoylpyrrolidine (DPOD) in toluene has been studied at varying concentrations of nitric acid, extractant, salting-out agent LiNO3 and at different temperatures.The mechanism of extraction is discussedin the light of the results obtained.

  8. Enhanced Droplet Control by Transition Boiling

    Science.gov (United States)

    Grounds, Alex; Still, Richard; Takashina, Kei

    2012-10-01

    A droplet of water on a heated surface can levitate over a film of gas produced by its own evaporation in the Leidenfrost effect. When the surface is prepared with ratchet-like saw-teeth topography, these droplets can self-propel and can even climb uphill. However, the extent to which the droplets can be controlled is limited by the physics of the Leidenfrost effect. Here, we show that transition boiling can be induced even at very high surface temperatures and provide additional control over the droplets. Ratchets with acute protrusions enable droplets to climb steeper inclines while ratchets with sub-structures enable their direction of motion to be controlled by varying the temperature of the surface. The droplets' departure from the Leidenfrost regime is assessed by analysing the sound produced by their boiling. We anticipate these techniques will enable the development of more sophisticated methods for controlling small droplets and heat transfer.

  9. Dynamic Bubble Behaviour during Microscale Subcooled Boiling

    Institute of Scientific and Technical Information of China (English)

    WANG Hao; PENG Xiao-Feng; David M.Christopher

    2005-01-01

    @@ Bubble cycles, including initiation, growth and departure, are the physical basis of nucleate boiling. The presentinvestigation, however, reveals unusual bubble motions during subcooled nucleate boiling on microwires 25 orl00μm in diameter. Two types of bubble motions, bubble sweeping and bubble return, are observed in theexperiments. Bubble sweeping describes a bubble moving back and forth along the wire, which is motion parallelto the wire. Bubble return is the bubble moving back to the wire after it has detached or leaping above thewire. Theoretical analyses and numerical simulations are conducted to investigate the driving mechanisms forboth bubble sweeping and return. Marangoni flow from warm to cool regions along the bubble interface is foundto produce the shear stresses needed to drive these unusual bubble movements.

  10. Pool Boiling Heat Transfer on structured Surfaces

    Science.gov (United States)

    Addy, J.; Olbricht, M.; Müller, B.; Luke, A.

    2016-09-01

    The development in the process and energy sector shows the importance of efficient utilization of available resources to improve thermal devices. To achieve this goal, all thermal components have to be optimized continuously. Various applications of multi-phase heat and mass transfer have to be improved. Therefore, the heat transfer and the influence of surface roughness in nucleate boiling with the working fluid propane is experimentally investigated on structured mild steel tubes, because only few data are available in the literature. The mild steel tube is sandblasted to obtain different surface roughness. The measurements are carried out over wide ranges of heat flux and pressure. The experimental results are compared with correlations from literature and the effect of surface roughness on the heat transfer is discussed. It is shown that the heat transfer coefficient increases with increasing surface roughness, heat flux and reduced pressure at nucleate pool boiling.

  11. Boiling Heat Transfer in Circulating Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    张利斌; 李修伦

    2001-01-01

    A model is proposed to predict boiling heat transfer coefficient in a three-phase circulating fluidized bed (CFB), which is a new type of evaporation boiling means for enhancing heat transfer and preventing fouling. To verify the model, experiments are conducted in a stainless steel column with 39 mm ID and 2.0 m height, in which the heat transfer coefficient is measured for different superficial velocities, steam pressures, particle concentrations and materials of particle. As the steam pressure and particle concentrations increase, the heat transfer coefficient in the bed increases. The heat transfer coefficient increases with the liquid velocity but it exhibits a local minimum.The heat transfer coefficient is correlated with cluster renewed model and two-mechanism method. The prediction of the model is in good agreement with experimental data.

  12. Boiling Heat Transfer in Circulating Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A model is proposed to predict boiling heat transfer coefficient in a three-phase circulating fluidized bed (CFB), which is a new type of evaporation boiling means for enhancing heat transfer and preventing fouling. To verify the model, experiments are conducted in a stainless steel column with 39mm ID and 2.0m height, in which the heat transfer coefficient is measured for different superficial velocities, steam pressures, particle concentrations and materials of particle. As the steam pressure and particle concentrations increase, the heat transfer coefficient in the bed increases. The heat transfer coefficient increases with the liquid velocity but it exhibits a local minimum. The heat transfer coefficient is correlated with cluster renewed model and two-mechanism method. The prediction of the model is in good agreement with experimental data.

  13. Self-propelled film-boiling liquids

    OpenAIRE

    Linke, H.; Aleman, B. J.; Melling, L. D.; Taormina, M. J.; Francis, M J; Dow-Hygelund, C. C.; Narayanan, V.; Taylor, R. P.; Stout, A.

    2005-01-01

    We report that liquids perform self-propelled motion when they are placed in contact with hot surfaces with asymmetric (ratchet-like) topology. The pumping effect is observed when the liquid is in the film-boiling regime, for many liquids and over a wide temperature range. We propose that liquid motion is driven by a viscous force exerted by vapor flow between the solid and the liquid.

  14. 交联柱撑皂土催化剂上甲苯的硝酸选择性硝化%Selective Nitration of Toluene with Nitric Acid on the Cross-linked Pillared Bentonite Catalysts

    Institute of Scientific and Technical Information of China (English)

    吕春绪; 彭新华

    2001-01-01

    在交联柱撑皂土催化下,应用硝酸硝化甲苯,能提高甲苯的对位选择性硝化能力,邻对硝基甲苯比例较通常硝硫混酸方法硝化邻对位产物比例(1.67)显著降低。在所制备的NH+4、H+、La3+等系列改性铝交联柱撑皂土催化剂中,稀土La3+改性交联柱撑皂土具有较好的催化选择性和活性,邻对硝基甲苯比例达到0.75。%Para-selectivities oi toluene nitrations were enhanced by using nitric acid as nitrating agent in the presence of cross-linked pillared bentonite catalysts.Ortho-to-para ratios were greatly below 1.67 as compared with sulfonitric acid.Of a range of NH+4、H+、La3+ modified aluminium cross-linked bentonites,La3+ modiried bentonite appears to be the optimum catalytic selectivity and reactivity,up to 0.75 in a ratio of ortho and para nitrotoluene.

  15. Pressure drop in saturated flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco J. [Universidad de Zaragoza, Zaragoza (Spain)

    2003-07-01

    A new mass balance for flow boiling have been recently suggested by the author following a quite simple idea: if the phases have different velocities, they can not cover the same distance -the control volume length for a 1-d system- in the same time. Thus, the time scales of the phases have to be different, and we should scale the time dependent magnitudes of one phase to the other one before combining them. Furthermore, it is reasonable to think that conservation equations should have to include in some manner this evident physical fact. In complete coherence with the former mass balance, a new energy balance, which does include the slip ratio has been also stated. This work, whilst reviews these new fundamentals for saturated flow boiling, stresses those aspects related with the prediction of the pressure drop in saturated flow boiling. The new correlations found for the data carefully measured by Thom during the Cambridge project would confirm the new two-phase flowapproach.

  16. Flow boiling test of GDP replacement coolants

    Energy Technology Data Exchange (ETDEWEB)

    Park, S.H. [comp.

    1995-08-01

    The tests were part of the CFC replacement program to identify and test alternate coolants to replace CFC-114 being used in the uranium enrichment plants at Paducah and Portsmouth. The coolants tested, C{sub 4}F{sub 10} and C{sub 4}F{sub 8}, were selected based on their compatibility with the uranium hexafluoride process gas and how well the boiling temperature and vapor pressure matched that of CFC-114. However, the heat of vaporization of both coolants is lower than that of CFC-114 requiring larger coolant mass flow than CFC-114 to remove the same amount of heat. The vapor pressure of these coolants is higher than CFC-114 within the cascade operational range, and each coolant can be used as a replacement coolant with some limitation at 3,300 hp operation. The results of the CFC-114/C{sub 4}F{sub 10} mixture tests show boiling heat transfer coefficient degraded to a minimum value with about 25% C{sub 4}F{sub 10} weight mixture in CFC-114 and the degree of degradation is about 20% from that of CFC-114 boiling heat transfer coefficient. This report consists of the final reports from Cudo Technologies, Ltd.

  17. Steady State Vapor Bubble in Pool Boiling

    Science.gov (United States)

    Zou, An; Chanana, Ashish; Agrawal, Amit; Wayner, Peter C.; Maroo, Shalabh C.

    2016-02-01

    Boiling, a dynamic and multiscale process, has been studied for several decades; however, a comprehensive understanding of the process is still lacking. The bubble ebullition cycle, which occurs over millisecond time-span, makes it extremely challenging to study near-surface interfacial characteristics of a single bubble. Here, we create a steady-state vapor bubble that can remain stable for hours in a pool of sub-cooled water using a femtosecond laser source. The stability of the bubble allows us to measure the contact-angle and perform in-situ imaging of the contact-line region and the microlayer, on hydrophilic and hydrophobic surfaces and in both degassed and regular (with dissolved air) water. The early growth stage of vapor bubble in degassed water shows a completely wetted bubble base with the microlayer, and the bubble does not depart from the surface due to reduced liquid pressure in the microlayer. Using experimental data and numerical simulations, we obtain permissible range of maximum heat transfer coefficient possible in nucleate boiling and the width of the evaporating layer in the contact-line region. This technique of creating and measuring fundamental characteristics of a stable vapor bubble will facilitate rational design of nanostructures for boiling enhancement and advance thermal management in electronics.

  18. Effect of fish oils containing different amounts of EPA, DHA, and antioxidants on plasma and brain fatty acids and brain nitric oxide synthase activity in rats

    OpenAIRE

    2009-01-01

    Background The interest in n-3 polyunsaturated fatty acids (PUFAs) has expanded significantly in the last few years, due to their many positive effects described. Consequently, the interest in fish oil supplementation has also increased, and many different types of fish oil supplements can be found on the market. Also, it is well known that these types of fatty acids are very easily oxidized, and that stability among supplements varies greatly. Aims of the study In this pilot study we investi...

  19. 硝酸氧化对沥青烯基有序介孔炭电化学性能的影响%The influence of nitric acid oxidation on the electrochemical performance of asphaltene-based ordered mesoporous carbon

    Institute of Scientific and Technical Information of China (English)

    王六平; 周颖; 邱介山

    2011-01-01

    采用硝酸对沥青烯基有序介孔炭(Ordered mesoporous carbon,OMC)进行氧化处理,在硝酸浓度为5mol/L、40℃~100℃下,考察了氧化温度对沥青烯基OMC的孔结构和电化学性能的影响,讨论了不同表面化学氛围的OMC孔道内电解液离子的传输过程.OMC的结构表征和性能测试采用XRD、物理吸附仪和电化学工作站等技术.结果表明:适度的硝酸氧化处理可以有效地改善OMC的电化学性能,低温氧化处理在化学改性OMC表面的同时,仍能保持其规则的孔道结构,比表面积和孔容基本不变;60℃氧化处理时,OMC表现出良好的双电层电化学行为和频率响应特性,电容器可以保持较快的充放电速率,时间常数约为6s;在5mV·s-1的扫描速率下其质量比电容值和能量密度分别为138F·g-1和3.9Wh·kg-1,较改性前分别提高了57%和63%.%Asphaltene-based ordered mesoporous carbon ( OMC) was oxidized with 5 mol/L nitric acid at 40-100 ℃ . The influence of nitric acid oxidation treatment on its textural properties and electrochemical performance as a supercapacitor electrode material was investigated and the ionic transport behavior in relation to surface chemical structure was discussed. The pore structures and electrochemical performance were examined using XRD, nitrogen adsorption and an electrochemical workstation. Results indicate that electrochemical performance can be improved with nitric acid treatment under mild conditions. The regular mesostructure can be retained, and the surface areas and pore volumes vary slightly when oxidation temperature is below 60 ℃ . A capacitor assembled with the OMC sample oxidized at 60℃ exhibits excellent electric double layer behavior, improved frequency response characteristics and a fast charge-discharge rate with a time constant of 6s. The gravimetric specific capacitance and energy density of OMC oxidized at 60 ℃ are 138 F·g-1 and 3. 9 Wh.kg-1 respectively at a scanning rate of 5 m

  20. Stability monitoring for boiling water reactors

    Science.gov (United States)

    Cecenas-Falcon, Miguel

    1999-11-01

    A methodology is presented to evaluate the stability properties of Boiling Water Reactors based on a reduced order model, power measurements, and a non-linear estimation technique. For a Boiling Water Reactor, the feedback reactivity imposed by the thermal-hydraulics has an important effect in the system stability, where the dominant contribution to this feedback reactivity is provided by the void reactivity. The feedback reactivity is a function of the operating conditions of the system, and cannot be directly measured. However, power measurements are relatively easy to obtain from the nuclear instrumentation and process computer, and are used in conjunction with a reduced order model to estimate the gain of the thermal-hydraulics feedback using an Extended Kalman Filter. The reduced order model is obtained by estimating the thermal-hydraulic transfer function from the frequency-domain BWR code LAPUR, and the stability properties are evaluated based on the pair of complex conjugate eigenvalues. Because of the recursive nature of the Kalman Filter, an estimate of the decay ratio is generated every sampling time, allowing continuous estimation of the stability parameters. A test platform based on a nuclear-coupled boiling channel is developed to validate the capability of the BWR stability monitoring methodology. The thermal-hydraulics for the boiling channel is modeled and coupled with neutron kinetics to analyze the non-linear dynamics of the closed-loop system. The model uses point kinetics to study core-wide oscillations, and normalized modal kinetics are introduced to study out-of-phase oscillations. The coolant flow dynamics is dominant in the power fluctuations observed by in-core nuclear instrumentation, and additive white noise is added to the solution for the channel flow in the thermal-hydraulic model to generate noisy power time series. The operating conditions of the channel can be modified to accommodate a wide range of stability conditions

  1. Experimental study about ONB and subcooled boiling heat transfer

    Energy Technology Data Exchange (ETDEWEB)

    Changhong, P.; Myint, A.; Yun, G.; Dounan, J. [State Key Laboratory of Multiphase Flow in power engineering, Department of Nuclear and Thermal Power Engineering, Xian (China)

    2004-07-01

    Water subcooled boiling heat transfer were experimentally investigated in the vertical annuli with narrow gap. Subcooled flow boiling covers the region from the location where the bubbles forms on the wall to the location where the bulk temperature reaches saturated temperature. Three locations in the subcooled flow boiling have been identified by earlier researchers as the onset of nucleate boiling (ONB), the beginning of fully developed boiling, and the location where the thermodynamic quality is zero that is inferred from the enthalpy balance equation. The heat transfer regions are identified as single-phase heat transfer prior to ONB, partial boiling (PB) and fully developed boiling (FDB). In this study, the available models for predicting heat transfer in the different regions and the modified correlation can predict our experimental data: -) the heat flux of ONB can be predicted by the Unal correlation, nevertheless the h{sub FC} is calculated by the modified Dittus-Boelter correlations in the narrow annuli, -) Griffith's method can be modified to identify the beginning of fully develop boiling, -) in the partial boiling region, the heat transfer coefficient can be calculated by h{sub PB} equals (1-a)*h{sub L} + a*h{sub FDB}, and -) in the fully developed region, the correlation for saturated flow boiling can be employed to describe the heat transfer.

  2. Linoleic acid-induced expression of inducible nitric oxide synthase and cyclooxygenase II via p42/44 mitogen-activated protein kinase and nuclear factor-kappaB pathway in retinal pigment epithelial cells.

    Science.gov (United States)

    Fang, I-Mo; Yang, Chang-Hao; Yang, Chung-May; Chen, Muh-Shy

    2007-11-01

    High linoleic acid (LA) intake is known to correlate with age-related macular degeneration (AMD), but the molecular mechanisms remain unclear. This study was conducted to investigate the effects of LA on expression of inducible nitric oxide synthase (iNOS) and cyclooxygenase II (COX-2) and their associated signaling pathways in human retinal pigment epithelial (RPE) cells. ARPE-19 cells were treated with different concentrations of LA. Expressions of iNOS and COX-2 were examined using semiquantitative reverse transcription polymerase chain reaction (RT-PCR) and Western blot analysis. Concentrations of nitric oxide (NO) and prostaglandin E(2) (PGE(2)) in the culture medium were determined by enzyme-link immunosorbent assay (ELISA). Activation of p42/44, p38, JNK mitogen-activated protein kinase (MAPK) and nuclear factors (NF)-kappaB were evaluated by Western blot analysis and electrophoretic mobility shift assay (EMSA). We found that LA induced expression of iNOS and COX-2 in RPE cells at the mRNA and protein levels in a time-and dose-dependent manner. Upregulation of iNOS and COX-2 resulted in increased production of NO and PGE(2). Moreover, LA caused degradation of IkappaB and increased NF-kappaB DNA binding activity. Effects of LA-induced iNOS and COX-2 expression were inhibited by a NF-kappaB inhibitor, pyrrolidine dithiocarbamate (PDTC). LA activated p42/44, but not p38 or JNK MAPK. Inhibition of p42/44 activity by PD98059 significantly reduced LA-induced activation of NF-kappaB. Linoleic acid-induced expression of iNOS and COX-2 as well as PGE(2) and NO release in RPE cells were sequentially mediated through activation of p42/p44, MAPK, then NF-kappaB. These results may provide new insights into both mechanisms of LA action on RPE cells and pathogenesis of age-related macular degeneration.

  3. Remedial Investigation Report on the Abandoned Nitric Acid Pipeline at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee. Energy Systems Environmental Restoration Program; Y-12 Environmental Restoration Program

    Energy Technology Data Exchange (ETDEWEB)

    1994-02-01

    Upper East Fork Poplar Creek Operable Unit 2 consists of the Abandoned Nitric Acid pipeline (ANAP). This pipeline was installed in 1951 to transport liquid wastes {approximately}4800 ft from Buildings 9212, 9215, and 9206 to the S-3 Ponds. Materials known to have been discharged through the pipeline include nitric acid, depleted and enriched uranium, various metal nitrates, salts, and lead skimmings. During the mid-1980s, sections of the pipeline were removed during various construction projects. A total of 19 locations were chosen to be investigated along the pipeline for the first phase of this Remedial Investigation. Sampling consisted of drilling down to obtain a soil sample at a depth immediately below the pipeline. Additional samples were obtained deeper in the subsurface depending upon the depth of the pipeline, the depth of the water table, and the point of auger refusal. The 19 samples collected below the pipeline were analyzed by the Oak Ridge Y-12 Plant`s laboratory for metals, nitrate/nitrite, and isotopic uranium. Samples collected from three boreholes were also analyzed for volatile organic compounds because these samples produced a response with organic vapor monitoring equipment. Uranium activities in the soil samples ranged from 0.53 to 13.0 pCi/g for {sup 238}U, from 0.075 to 0.75 pCi/g for {sup 235}U, and from 0.71 to 5.0 pCi/g for {sup 238}U. Maximum total values for lead, chromium, and nickel were 75.1 mg/kg, 56.3 mg/kg, and 53.0 mg/kg, respectively. The maximum nitrate/nitrite value detected was 32.0 mg-N/kg. One sample obtained adjacent to a sewer line contained various organic compounds, at least some of which were tentatively identified as fragrance chemicals commonly associated with soaps and cleaning solutions. The results of the baseline human health risk assessment for the ANAP contaminants of potential concern show no unacceptable risks to human health.

  4. 氮掺杂钛精矿的制备及其可见光催化活性%Preparation of nitric acid-modified titanium ore and its visible-light photocatalytic activity

    Institute of Scientific and Technical Information of China (English)

    雷雪飞; 薛向欣; 杨合

    2013-01-01

    Nitric acid-modified titanium ore (NATO) photocatalysts were prepared by the high energy ball milling method at different temperature. NATO photocatalysts were characterized by XRD, FT-IR, UV-Vis absorption spectra, TG-DTA and PL measurements. Its photocatalytic activity was checked through the photocatalytic oxidation of methyl orange as a model compound under vis light irradiation. The results showed that: mixed crystal structure was found in NATO photocatalysts; the photocatalytic activities of NATO calcined at 400℃ showed a higher catalytic activity compared to other catalysts; the higher concentration of nitrate and the visible absorption capacity,and the suitable phase ratio led to the enhancement of the photocatalytic activities of NATO calcined at 400℃ ; the decoloration rate of methyl orange reached 100% after 1h.%以硝酸作为氮源,钛精矿为原料,采用超声波复合高能球磨法,在不同煅烧温度下合成了硝酸掺杂的钛精矿催化剂(nitric acid-modified titanium ore,NATO).用X射线衍射(XRD)、傅立叶红外(FTIR)、紫外-可见漫反射光谱(UV-Vis)、差热-热重(TGDTA)和光致发光谱(PL)分析对NATO催化剂的结构和性能进行分析和表征,确定其由钛磁铁矿、钛铁矿、TiO2、钛铁氧化物等多种物相组成;在紫外-可见光区域都具有很强的光吸收能力.不同煅烧温度下,NATO催化剂的光催化活性由甲基橙的脱色率来评价,结果表明,煅烧温度为400℃时,NATO催化剂由于表面存在较高的硝酸盐含量和较高的可见光吸收能力及合适的晶相比,而具有较高的光催化活性,500W金卤灯照射1h,可将浓度为10mg/L的甲基橙废水完全降解.

  5. Nitric oxide promotes survival of cerebellar granule neurons cultured in vitro through the Akt pathway

    Institute of Scientific and Technical Information of China (English)

    Lin Wang; Mei Li; Lihua Zhou

    2011-01-01

    In this study, cerebellar granule neurons were used to examine the role of nitric oxide on cell survival. The N-methyl-D-aspartic acid receptor antagonist, MK-801, and the soluble guanylate cyclase antagonist, 1H-[1, 2, 4]oxadiazolo-[4, 3-a] quinoxalin-1-one, decreased cell viability, induced caspase-3, and decreased phosphorylated-Akt levels, suggesting that blockade of nitric oxide production promotes apoptosis of differentiating cerebellar granule neurons. After administration of sodium nitroprusside, an endogenous nitric oxide donor, cell viability recovered,caspase-3 expression was decreased, and phosphorylated-Akt levels increased. This study provides direct evidence that nitric oxide can sustain the survival of developing cerebellar granule neurons in vitro through the nitric oxide-Akt pathway. Moreover, endogenous nitric oxide exerts these effects in a cyclic guanosine monophosphate-dependent manner while exogenous nitric oxide does so in a cyclic guanosine monophosphate-independent manner.

  6. Lattice Boltzmann modeling of boiling heat transfer: The boiling curve and the effects of wettability

    OpenAIRE

    Li, Q; Kang, Q. J.; Francois, M. M.; He, Y. L.; Luo, K. H.

    2015-01-01

    A hybrid thermal lattice Boltzmann (LB) model is presented to simulate thermal multiphase flows with phase change based on an improved pseudopotential LB approach [Q. Li, K. H. Luo, and X. J. Li, Phys. Rev. E 87, 053301 (2013)]. The present model does not suffer from the spurious term caused by the forcing-term effect, which was encountered in some previous thermal LB models for liquid-vapor phase change. Using the model, the liquid-vapor boiling process is simulated. The boiling curve togeth...

  7. A review on boiling heat transfer enhancement with nanofluids.

    Science.gov (United States)

    Barber, Jacqueline; Brutin, David; Tadrist, Lounes

    2011-04-04

    There has been increasing interest of late in nanofluid boiling and its use in heat transfer enhancement. This article covers recent advances in the last decade by researchers in both pool boiling and convective boiling applications, with nanofluids as the working fluid. The available data in the literature is reviewed in terms of enhancements, and degradations in the nucleate boiling heat transfer and critical heat flux. Conflicting data have been presented in the literature on the effect that nanofluids have on the boiling heat-transfer coefficient; however, almost all researchers have noted an enhancement in the critical heat flux during nanofluid boiling. Several researchers have observed nanoparticle deposition at the heater surface, which they have related back to the critical heat flux enhancement.

  8. 双亚砜与TBP对铀(Ⅵ)萃取行为的比较%Comparision of extraction of U(Ⅵ) from nitric acid by disulfoxides and TBP

    Institute of Scientific and Technical Information of China (English)

    朱利明; 匡华; 崔立燕; 孙永辉; 曹正白

    2001-01-01

    研究了PhSO(CH2)nSOPh(n=2、3、4、6)-三氯甲烷体系从硝酸介质中萃取铀的行为。n=2的双亚砜在萃取时出现三相,n=3、4、6的三种双亚砜对铀的萃取规律类似于TBP,萃取性能略优于TBP。铀的溶剂化数均为1。%The extraction of dioxouranium(Ⅵ) from nitric acid solution byPhSO(CH2)nSOPh (n=2,3,4,6)-trichloromethane was studied. When the disulfoxide was PhSO(CH2)2SOPh, the third phase formed. The extraction laws of dioxouranium(Ⅵ) by the disulfoxides (n=3,4,6) were similar to that by tributyl-phosphate(TBP). Their extracting ability was slightly better than that of TBP.

  9. 从低浓度含钯硝浸液中富集钯工艺研究%Research on Concentration of Palladium from Nitric Acid Leaching Solution Containing Palladium

    Institute of Scientific and Technical Information of China (English)

    赵祝鹏; 王兴; 崔家友; 张善辉; 侯绍彬; 姜学利

    2016-01-01

    针对在银电解过程中产生的银阳极泥,研究了硝酸浸出溶解银和钯,然后采用食盐沉银、黄药富集分离钯的生产工艺。研究结果表明,银回收率在98%以上,钯富集率达到93%以上。同时,该工艺具有成本低、操作简单、贵金属回收率高等优点。%Aimed at silver anode slime produced in the course of silver electrolytic refining, Ag and Pd are dissolved by nitric acid, then Ag is subsided by salt and Pd is concentrated by butyl xanthate. The recovery rate of Ag is over 98%, the accumulation rate of Pd reaches to 93%. The process has the advantages of low cost, simple operation, high precious metals recovery.

  10. Study of the reaction between {sup 51}CrO{sub 3} and concentrated nitric acid by radio chromatographic methods; Estudo da reacao entre {sup 51}CrO{sub 3} e acido nitrico concentrado por metodos radiocromatograficos

    Energy Technology Data Exchange (ETDEWEB)

    Pezzin, Sergio H. [Univesidade do Estado de Santa Catarina (UDESC), Joinville, SC (Brazil). Centro de Ciencias Tecnologicas; Collins, Carol H.; Collins, Kenneth E. [Universidade Estadual de Campinas, SP (Brazil). Inst. de Quimica

    2000-07-01

    The objective of the present work is to verify the reduction of CrO{sub 3} in concentrated nitric acid, using {sup 51}Cr as a tracer. For the study, {sup 51}CrO{sub 3} (ca. 200,000 cpm/mg) was added to 65% HNO{sub 3} and maintained under agitation at 20 deg C for specified time periods. Aliquots (100 {mu}) were analyzed by open column cation (AG50Wx8, 100-200 mesh, Na{sup +} form) chromatography, either immediately or after dilution to approximately pH 2 and storage for specified time periods. The separations, which were made by stepwise elution using HClO{sub 4} and Ca(ClO{sub 4}){sub 2} solutions as effluents with fraction collection, followed by counting with a NaI(Tl) detector and a single channel analyzer. It was verified that ca. 3.5% of Cr(III) is obtained after 15 min of reaction. The major reaction product is hexaaquo chromium(III), with minor concentrations of mononitrate penta-aquochromium(III), [Cr(H{sub 2}O){sub 5}NO{sub 3}]{sup 2+}, a product which undergoes watering at pH 2 to produce, after 360 h, [Cr(H{sub 2}O){sub 6}]{sup 3+}. (author)

  11. Sublethal concentrations of salicylic acid decrease the formation of reactive oxygen species but maintain an increased nitric oxide production in the root apex of the ethylene-insensitive never ripe tomato mutants.

    Science.gov (United States)

    Tari, Irma; Poór, Péter; Gémes, Katalin

    2011-09-01

    The pattern of salicylic acid (SA)-induced production of reactive oxygen species (ROS) and nitric oxide (NO) were different in the apex of adventitious roots in wild-type and in the ethylene-insensitive never ripe (Nr) mutants of tomato (Solanum lycopersicum L. cv Ailsa Craig). ROS were upregulated, while NO remained at the control level in apical root tissues of wildtype plants exposed to sublethal concentrations of SA. In contrast, Nr plants expressing a defective ethylene receptor displayed a reduced level of RO S and a higher NO content in the apical root cells. In wild-type plants NO production seems to be RO S(H2O2)-dependent at cell death-inducing concentrations of SA, indicating that ROS and NO may interact to trigger oxidative cell death. In the absence of significant RO S accumulation, the increased NO production caused moderate reduction in cell viability in root apex of Nr plants exposed to 10(-3) M SA. This suggests that a functional ethylene signaling pathway is necessary for the control of ROS and NO production induced by SA.

  12. Extraction of Th(IV) from nitric acid with 40—benzoyl—2,4—dihydro—5—methyl—2—phenyl—3H—pyrazol—3—thione

    Institute of Scientific and Technical Information of China (English)

    YuShao-Ning; YangYan-Zhao; 等

    1998-01-01

    The BMPPT(4-benzoyl-2,4-dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione)was synthesized from BMPP.Its m.p.is 106-108℃,The results of the element analysis are as follows:C,68.51%,H,4.51%,N,9.26%,S.11.47%,which are in conformity with the theoretical value(C,69.15%,H,4.76%,N.9.52%,S.10.90%),The solvent extraction of Th4+ from nitric acid solution by BMPPT in benzene was studied.The extraction ability of BMPPT is not so high as that of its parent (BMPP).The Th4+ distribution ratio(DTh)in creases with the increasing pH of the aqueous phase,and pH1/2 for Th4+ was 3.2([BMPPT]=0.10mol/L),When the pH increases,the distribution ratio of Th4+ increasdes linearly with the slope of 1.59,When the concentration of BMPPT increases,the distribution ratio of Th4+ increases rapidly.The lgDTh-lg[BMPPT]is linear with the slope of 1.42 and the extraction mechanism is the cation ion-exchange.

  13. Subcooled pool boiling CHF in ethanol

    OpenAIRE

    Park, Jongdoc; Fukuda, Katsuya; Liu, Qiusheng

    2006-01-01

    Steady-state and transient critical heat fluxes (CHFs) were measured using a 1.0 mm diameter horizontal cylinder in a pool of highly wetting liquid, such as ethanol, due to steady and transient heat generation rate for wide range of subcoolings and pressures. Boiling CHF was assumed to happen based on a kind of hydrodynamic instability (HI) at CHF, and the model is supposed that the increase in vapor generation from the cylinder surface causes a limit of the steady-state vapor escape flow whe...

  14. Boiling heat transfer modern developments and advances

    CERN Document Server

    Lahey, Jr, RT

    2013-01-01

    This volume covers the modern developments in boiling heat transfer and two-phase flow, and is intended to provide industrial, government and academic researchers with state-of-the-art research findings in the area of multiphase flow and heat transfer technology. Special attention is given to technology transfer, indicating how recent significant results may be used for practical applications. The chapters give detailed technical material that will be useful to engineers and scientists who work in the field of multiphase flow and heat transfer. The authors of all chapters are members of the

  15. Pool boiling heat transfer performance of Newtonian nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Soltani, Saide; Etemad, Seyed Gholamreza [Isfahan University of Technology, Department of Chemical Engineering, Isfahan (Iran); Thibault, Jules [University of Ottawa, Department of Chemical and Biological Engineering, Ottawa, ON (Canada)

    2009-10-15

    Experimental measurements were carried out on the boiling heat transfer characteristics of {gamma}-Al{sub 2}O{sub 3}/water and SnO{sub 2}/water Newtonian nanofluids. Nanofluids are liquid suspensions containing nanoparticles with sizes smaller than 100 nm. In this research, suspensions with different concentrations of {gamma}-Al{sub 2}O{sub 3} and SnO{sub 2} nanoparticles in water were studied under nucleate pool boiling heat transfer conditions. Results show that nanofluids possess noticeably higher boiling heat transfer coefficients than the base fluid. The boiling heat transfer coefficients depend on the type and concentration of nanoparticles. (orig.)

  16. Investigation of Enhanced Boiling Heat Transfer from Porous Surfaces

    Institute of Scientific and Technical Information of China (English)

    LinZhiping; MaTongze; 等

    1994-01-01

    Experimental investigations of boiling heat transfer from porous surfaces at atmospheric pressure were performne.The porous surfaces are plain tubes coverd with metal screens.V-shaped groove tubes covered with screens,plain tubes sintered with screens.and V-shaped groove tubes sintered with screens,The experimental results show that sintering metal screens around spiral V-shaped groove tubes can greatly improve the boiling heat transfer,The boiling hystesis was observed in the experiment.This paper discusses the mechanism of the boiling heat transfer from those kinds of porous surfaces stated above.

  17. Boiling Experiment Facility for Heat Transfer Studies in Microgravity

    Science.gov (United States)

    Delombard, Richard; McQuillen, John; Chao, David

    2008-01-01

    Pool boiling in microgravity is an area of both scientific and practical interest. By conducting tests in microgravity, it is possible to assess the effect of buoyancy on the overall boiling process and assess the relative magnitude of effects with regards to other "forces" and phenomena such as Marangoni forces, liquid momentum forces, and microlayer evaporation. The Boiling eXperiment Facility is now being built for the Microgravity Science Glovebox that will use normal perfluorohexane as a test fluid to extend the range of test conditions to include longer test durations and less liquid subcooling. Two experiments, the Microheater Array Boiling Experiment and the Nucleate Pool Boiling eXperiment will use the Boiling eXperiment Facility. The objectives of these studies are to determine the differences in local boiling heat transfer mechanisms in microgravity and normal gravity from nucleate boiling, through critical heat flux and into the transition boiling regime and to examine the bubble nucleation, growth, departure and coalescence processes. Custom-designed heaters will be utilized to achieve these objectives.

  18. Modal control of unstable boiling states in three-dimensional nonlinear pool-boiling

    NARCIS (Netherlands)

    Gils, van R.W.; Speetjens, M.F.M; Zwart, H.J.; Nijmeijer, H.

    2014-01-01

    Topic is feedback stabilisation of a nonlinear pool-boiling system in three spatial dimensions (3D). Regulation of its unstable (non-uniform) equilibria has great potential for application in micro-electronics cooling and thermal-management systems. Here, as a first step, stabilisation of such 3D eq

  19. Role of Nitric Oxide and Hydrogen Sulfide in the Vasodilator Effect of Ursolic Acid and Uvaol from Black Cherry Prunus serotina Fruits.

    Science.gov (United States)

    Luna-Vázquez, Francisco J; Ibarra-Alvarado, César; Rojas-Molina, Alejandra; Romo-Mancillas, Antonio; López-Vallejo, Fabián H; Solís-Gutiérrez, Mariana; Rojas-Molina, Juana I; Rivero-Cruz, Fausto

    2016-01-12

    The present research aimed to isolate the non-polar secondary metabolites that produce the vasodilator effects induced by the dichloromethane extract of Prunus serotina (P. serotina) fruits and to determine whether the NO/cGMP and the H2S/KATP channel pathways are involved in their mechanism of action. A bioactivity-directed fractionation of the dichloromethane extract of P. serotina fruits led to the isolation of ursolic acid and uvaol as the main non-polar vasodilator compounds. These compounds showed significant relaxant effect on rat aortic rings in an endothelium- and concentration-dependent manner, which was inhibited by NG-nitro-L-arginine methyl ester (L-NAME), DL-propargylglycine (PAG) and glibenclamide (Gli). Additionally, both triterpenes increased NO and H2S production in aortic tissue. Molecular docking studies showed that ursolic acid and uvaol are able to bind to endothelial NOS and CSE with high affinity for residues that form the oligomeric interface of both enzymes. These results suggest that the vasodilator effect produced by ursolic acid and uvaol contained in P. serotina fruits, involves activation of the NO/cGMP and H2S/KATP channel pathways, possibly through direct activation of NOS and CSE.

  20. Development boiling to sprinkled tube bundle

    Directory of Open Access Journals (Sweden)

    Kracík Petr

    2016-01-01

    Full Text Available This paper presents results of a studied heat transfer coefficient at the surface of a sprinkled tube bundle where boiling occurs. Research in the area of sprinkled exchangers can be divided into two major parts. The first part is research on heat transfer and determination of the heat transfer coefficient at sprinkled tube bundles for various liquids, whether boiling or not. The second part is testing of sprinkle modes for various tube diameters, tube pitches and tube materials and determination of individual modes’ interface. All results published so far for water as the falling film liquid apply to one to three tubes for which the mentioned relations studied are determined in rigid laboratory conditions defined strictly in advance. The sprinkled tubes were not viewed from the operational perspective where there are more tubes and various modes may occur in different parts with various heat transfer values. The article focuses on these processes. The tube is located in a low-pressure chamber where vacuum is generated using an exhauster via ejector. The tube consists of smooth copper tubes of 12 mm diameter placed horizontally one above another.

  1. Unsteady heat transfer during subcooled film boiling

    Science.gov (United States)

    Yagov, V. V.; Zabirov, A. R.; Lexin, M. A.

    2015-11-01

    Cooling of high-temperature bodies in subcooled liquid is of importance for quenching technologies and also for understanding the processes initiating vapor explosion. An analysis of the available experimental information shows that the mechanisms governing heat transfer in these processes are interpreted ambiguously; a more clear-cut definition of the Leidenfrost temperature notion is required. The results of experimental observations (Hewitt, Kenning, and previous investigations performed by the authors of this article) allow us to draw a conclusion that there exists a special mode of intense heat transfer during film boil- ing of highly subcooled liquid. For revealing regularities and mechanisms governing intense transfer of energy in this process, specialists of Moscow Power Engineering Institute's (MPEI) Department of Engineering Thermal Physics conduct systematic works aimed at investigating the cooling of high-temperature balls made of different metals in water with a temperature ranging from 20 to 100°C. It has been determined that the field of temperatures that takes place in balls with a diameter of more than 30 mm in intense cooling modes loses its spherical symmetry. An approximate procedure for solving the inverse thermal conductivity problem for calculating the heat flux density on the ball surface is developed. During film boiling, in which the ball surface temperature is well above the critical level for water, and in which liquid cannot come in direct contact with the wall, the calculated heat fluxes reach 3-7 MW/m2.

  2. Development boiling to sprinkled tube bundle

    Science.gov (United States)

    Kracík, Petr; Pospíšil, Jiří

    2016-03-01

    This paper presents results of a studied heat transfer coefficient at the surface of a sprinkled tube bundle where boiling occurs. Research in the area of sprinkled exchangers can be divided into two major parts. The first part is research on heat transfer and determination of the heat transfer coefficient at sprinkled tube bundles for various liquids, whether boiling or not. The second part is testing of sprinkle modes for various tube diameters, tube pitches and tube materials and determination of individual modes' interface. All results published so far for water as the falling film liquid apply to one to three tubes for which the mentioned relations studied are determined in rigid laboratory conditions defined strictly in advance. The sprinkled tubes were not viewed from the operational perspective where there are more tubes and various modes may occur in different parts with various heat transfer values. The article focuses on these processes. The tube is located in a low-pressure chamber where vacuum is generated using an exhauster via ejector. The tube consists of smooth copper tubes of 12 mm diameter placed horizontally one above another.

  3. Zero boil-off system testing

    Science.gov (United States)

    Plachta, D. W.; Johnson, W. L.; Feller, J. R.

    2016-03-01

    Cryogenic propellants such as liquid hydrogen (LH2) and liquid oxygen (LO2) are a part of NASA's future space exploration plans due to their high specific impulse for rocket motors of upper stages. However, the low storage temperatures of LH2 and LO2 cause substantial boil-off losses for long duration missions. These losses can be eliminated by incorporating high performance cryocooler technology to intercept heat load to the propellant tanks and modulating the cryocooler temperature to control tank pressure. The technology being developed by NASA is the reverse turbo-Brayton cycle cryocooler and its integration to the propellant tank through a distributed cooling tubing network coupled to the tank wall. This configuration was recently tested at NASA Glenn Research Center in a vacuum chamber and cryoshroud that simulated the essential thermal aspects of low Earth orbit, its vacuum and temperature. This test series established that the active cooling system integrated with the propellant tank eliminated boil-off and robustly controlled tank pressure.

  4. Kinetics of Silver Dissolution in Nitric Acid from Ag-Au0.04-Cu0.10 and Ag-Cu0.23 Scraps

    Institute of Scientific and Technical Information of China (English)

    S.K.Sadrnezhaad; E.Ahmadi; M.Mozammel

    2006-01-01

    Kinetics of dissolution of silver present in precious metal scraps in HNO3 was studied in temperature range of 26~85℃. Dissolution rate of silver was much faster than that of copper at all temperatures. Effects of particle size, stirring speed, acid concentration and temperature on the rate of dissolving of silver were evaluated.Dissolution rate decreases with particle size and increases with temperature. Dissolving was accelerated with acid concentrations less than 10 mol/L. Concentrations greater than 10 mol/L resulted in slowing down of the dissolution rate. Shrinking core model with internal diffusion equation t/τ=1-3(1-x)2/3+2(1-x)could be used to explain the mechanism of the reaction. Silver extraction resulted in activation energies of 33.95 k J/mol for Ag-Au0.04-Cu0.10 and 68.87 k J/mol for Ag-Cu0.23 particles. Inter-diffusion of silver and nitrate ions through the porous region of the insoluble alloying layer was the main resistance to the dissolving process. Results were tangible for applications in recycling of the material from electronic silver-bearing scraps, dental alloys,jewelry, silverware and anodic slime precious metal recovery.

  5. Rewetting and Flow Film Boiling Along Hot Surface

    Institute of Scientific and Technical Information of China (English)

    王补宣Thermal Engineering Department; Tsinghua University; Beijing 100084; PRC; 彭晓峰

    1994-01-01

    The recent investigations on the rewettmg and film boiling of liquid flowing along a hot/heated surface are briefly reviewed and discussed.Some advanced theoretical analyses are conducted and new conclusions achieved.These investigations describe the fundamental characteristics of liquid flow boiling and further the complicated rewetting phenomena,and have resulted in considerable insight intothe mechanism.

  6. Thermal-hydraulic performance of convective boiling jet array impingement

    Science.gov (United States)

    Jenkins, R.; De Brún, C.; Kempers, R.; Lupoi, R.; Robinson, A. J.

    2016-09-01

    Jet impingement boiling is investigated with regard to heat transfer and pressure drop performance using a novel laser sintered 3D printed jet impingement manifold design. Water was the working fluid at atmospheric pressure with inlet subcooling of 7oC. The convective boiling performance of the impinging jet system was investigated for a flat copper target surface for 2700≤Re≤5400. The results indicate that the heat transfer performance of the impinging jet is independent of Reynolds number for fully developed boiling. Also, the investigation of nozzle to plate spacing shows that low spacing delays the onset of nucleate boiling causing a superheat overshoot that is not observed with larger gaps. However, no sensitivity to the gap spacing was measured once boiling was fully developed. The assessment of the pressure drop performance showed that the design effectively transfers heat with low pumping power requirements. In particular, owing to the insensitivity of the heat transfer to flow rate during fully developed boiling, the coefficient of performance of jet impingement boiling in the fully developed boiling regime deteriorates with increased flow rate due to the increase in pumping power flux.

  7. Low-Flow Film Boiling Heat Transfer on Vertical Surfaces

    DEFF Research Database (Denmark)

    Munthe Andersen, J. G.; Dix, G. E.; Leonard, J. E.

    1976-01-01

    The phenomenon of film boiling heat transfer for high wall temperatures has been investigated. Based on the assumption of laminar flow for the film, the continuity, momentum, and energy equations for the vapor film are solved and a Bromley-type analytical expression for the heat transfer...... length, an average film boiling heat transfer coefficient is obtained....

  8. Explosive Boiling at Very Low Heat Fluxes: A Microgravity Phenomenon

    Science.gov (United States)

    Hasan, M. M.; Lin, C. S.; Knoll, R. H.; Bentz, M. D.

    1993-01-01

    The paper presents experimental observations of explosive boiling from a large (relative to bubble sizes) flat heating surface at very low heat fluxes in microgravity. The explosive boiling is characterized as either a rapid growth of vapor mass over the entire heating surface due to the flashing of superheated liquid or a violent boiling spread following the appearance of single bubbles on the heating surface. Pool boiling data with saturated Freon 113 was obtained in the microgravity environment of the space shuttle. The unique features of the experimental results are the sustainability of high liquid superheat for long periods and the occurrence of explosive boiling at low heat fluxes (0.2 to 1.2 kW/sq m). For a heat flux of 1.0 kW/sq m a wall superheat of 17.9 degrees C was attained in ten minutes of heating. This was followed by an explosive boiling accompanied with a pressure spike and a violent bulk liquid motion. However, at this heat flux the vapor blanketing the heating surface could not be sustained. Stable nucleate boiling continued following the explosive boiling.

  9. Critical heat flux in flow boiling in microchannels

    CERN Document Server

    Saha, Sujoy Kumar

    2015-01-01

    This Brief concerns the important problem of critical heat flux in flow boiling in microchannels. A companion edition in the SpringerBrief Subseries on Thermal Engineering and Applied Science to “Heat Transfer and Pressure Drop in Flow Boiling in Microchannels,” by the same author team, this volume is idea for professionals, researchers, and graduate students concerned with electronic cooling.

  10. Boiling treatment of ABS and PS plastics for flotation separation.

    Science.gov (United States)

    Wang, Chong-qing; Wang, Hui; Wu, Bao-xin; Liu, Qun

    2014-07-01

    A new physical method, namely boiling treatment, was developed to aid flotation separation of acrylonitrile-butadiene-styrene (ABS) and polystyrene (PS) plastics. Boiling treatment was shown to be effective in producing a hydrophilic surface on ABS plastic. Fourier Transform Infrared analysis was conducted to investigate the mechanism of boiling treatment of ABS. Surface rearrangement of polymer may be responsible for surface change of boiling treated ABS, and the selective influence of boiling treatment on the floatability of boiling treated plastics may be attributed to the difference in the molecular mobility of polymer chains. The effects of flotation time, frother concentration and particle size on flotation behavior of simple plastic were investigated. Based on flotation behavior of simple plastic, flotation separation of boiling treatment ABS and PS with different particle sizes was achieved efficiently. The purity of ABS and PS was up to 99.78% and 95.80%, respectively; the recovery of ABS and PS was up to 95.81% and 99.82%, respectively. Boiling treatment promotes the industrial application of plastics flotation and facilitates plastic recycling.

  11. Influence of Pressure on Stable Film Boiling of Subcooled Liquid

    Science.gov (United States)

    Zabirov, A. R.; Yagov, V. V.; Kaban'kov, O. N.; Leksin, M. A.; Kanin, P. K.

    2016-11-01

    Film boiling of subcooled liquids is an integral part of the hardening process. Understanding of the mechanisms underlying film boiling is important for modeling processes in atomic power engineering and cryogenic technology. Stationary processes of film boiling of subcooled liquids under conditions of their free motion near cylindrical heaters, just as subcooled liquid turbulent flow past high-temperature surfaces, represent quite a different type of process. In cooling metal spheres heated to a high temperature by a subcooled water, a special regime of film boiling is observed (microbubble boiling) distinguished by high intensity of heat transfer. Such a regime has not been revealed up to now for nonaqueous liquids. The paper presents new experimental data on heat transfer regimes in cooling nickel spheres in subcooled isopropanol and perfluorohexane at pressures of up to 1 MPa. It has been established that stable film boiling is the main regime of heat transfer that accounts for the larger part of the total time of cooling. The regimes of highly intensive film boiling heat transfer were not observed in the entire range of operational parameters even in the case of extreme subcoolings of liquid below their saturation temperature (to 170 K). The intensity of heat transfer in stable film boiling increases noticeably with subcooling of a chilling liquid.

  12. Direct Numerical Simulation and Visualization of Subcooled Pool Boiling

    Directory of Open Access Journals (Sweden)

    Tomoaki Kunugi

    2014-01-01

    Full Text Available A direct numerical simulation of the boiling phenomena is one of the promising approaches in order to clarify their heat transfer characteristics and discuss the mechanism. During these decades, many DNS procedures have been developed according to the recent high performance computers and computational technologies. In this paper, the state of the art of direct numerical simulation of the pool boiling phenomena during mostly two decades is briefly summarized at first, and then the nonempirical boiling and condensation model proposed by the authors is introduced into the MARS (MultiInterface Advection and Reconstruction Solver developed by the authors. On the other hand, in order to clarify the boiling bubble behaviors under the subcooled conditions, the subcooled pool boiling experiments are also performed by using a high speed and high spatial resolution camera with a highly magnified telescope. Resulting from the numerical simulations of the subcooled pool boiling phenomena, the numerical results obtained by the MARS are validated by being compared to the experimental ones and the existing analytical solutions. The numerical results regarding the time evolution of the boiling bubble departure process under the subcooled conditions show a very good agreement with the experimental results. In conclusion, it can be said that the proposed nonempirical boiling and condensation model combined with the MARS has been validated.

  13. Boiling in porous media; Ebullition en milieux poreux

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-11

    This conference day of the French society of thermal engineers was devoted to the analysis of heat transfers and fluid flows during boiling phenomena in porous media. This book of proceedings comprises 8 communications entitled: `boiling in porous medium: effect of natural convection in the liquid zone`; `numerical modeling of boiling in porous media using a `dual-fluid` approach: asymmetrical characteristic of the phenomenon`; `boiling during fluid flow in an induction heated porous column`; `cooling of corium fragment beds during a severe accident. State of the art and the SILFIDE experimental project`; `state of knowledge about the cooling of a particulates bed during a reactor accident`; `mass transfer analysis inside a concrete slab during fire resistance tests`; `heat transfers and boiling in porous media. Experimental analysis and modeling`; `concrete in accidental situation - influence of boundary conditions (thermal, hydric) - case studies`. (J.S.)

  14. Effect of boiling and roasting on the fermentation of soybeans into dawadawa (soy-dawadawa).

    Science.gov (United States)

    Dakwa, Sarah; Sakyi-Dawson, Esther; Diako, Charles; Annan, Nana Takyiwa; Amoa-Awua, Wisdom Kofi

    2005-09-25

    Soybeans which had initially been dehulled by either boiling (boiled/dehulled) or roasting (roasted/dehulled) before peeling, were cooked and fermented into dawadawa, a traditional food condiment. The micropopulation, enzymatic activities, proximate composition, amino acid, and aroma profiles of the two types of soybean dawadawa were evaluated during fermentation. Only minor differences were found in the microbial profiles of the two types of soy-dawadawa. Although boiled/dehulled soy-dawadawa initially had lower microbial counts, it recorded higher counts at the advanced stages of fermentation. Proteolytic and amylolytic Bacillus species including Bacillus subtilis, Bacillus pumilus, Bacillus licheniformis, Bacillus cereus, and Bacillus firmus dominated the micropopulation of the two types of soy-dawadawa with Bacillus subtilis accounting for about 50% of the Bacillus species in all samples. Lactic acid bacteria and yeasts occurred in low numbers in the two types of soy-dawadawa. The proximate composition of the two types of soy-dawadawa were similar, and their contents of moisture and protein increased whilst fat and ash decreased during fermentation. Both types of fermenting soy-dawadawa recorded similar levels of alpha-amylase activity, but boiled/dehulled soy-dawadawa showed slightly higher protease activity. The levels of isoleucine, leucine, lysine, phenylalanine, arginine and proline increased significantly with fermentation time in both types of soy-dawadawa. With respect to differences in their aroma profiles, hexanodecanol, octadecyl acetate, 1,2-dimethyl benzene, tetradecene, (E)-5-eicosene, cyclohexadecane, and hexacosane were found only in the roasted/dehulled samples, whilst 1,2-ethanediol, ethyl acetate, dimethyl disulfide, cyclotetradecane, decene, indole , 2 butyl-octenal, acetophenone, and toluene were found only in the boiled/dehulled samples. A market focus group showed preference for roasted/dehulled soy-dawadawa over boiled/dehulled soy

  15. High level disinfection of a home care device; to boil or not to boil?

    Science.gov (United States)

    Winthrop, K L; Homestead, N

    2012-03-01

    We developed a percutaneous electrical transducer for home therapy of chronic pain, a device that requires high level disinfection between uses. The utility of boiling water to provide high level disinfection was evaluated by inoculating transducer pads with potential skin pathogens (Staphylococcus aureus, Mycobacterium terrae, Pseudomonas aeruginosa, Candida albicans) and subjecting them to full immersion in water boiling at 4200 feet elevation (95 °C). Log10 reductions in colony-forming units (cfu) at 10 min were 7.1, >6.3 and >5.5 for S. aureus, P. aeruginosa and C. albicans, respectively, but only 4.6 for M. terrae. At 15 min the reductions had increased to 7.5, >6.8, >6.6 and >7.5 cfu, respectively.

  16. Hybrid modelling of a sugar boiling process

    CERN Document Server

    Lauret, Alfred Jean Philippe; Gatina, Jean Claude

    2012-01-01

    The first and maybe the most important step in designing a model-based predictive controller is to develop a model that is as accurate as possible and that is valid under a wide range of operating conditions. The sugar boiling process is a strongly nonlinear and nonstationary process. The main process nonlinearities are represented by the crystal growth rate. This paper addresses the development of the crystal growth rate model according to two approaches. The first approach is classical and consists of determining the parameters of the empirical expressions of the growth rate through the use of a nonlinear programming optimization technique. The second is a novel modeling strategy that combines an artificial neural network (ANN) as an approximator of the growth rate with prior knowledge represented by the mass balance of sucrose crystals. The first results show that the first type of model performs local fitting while the second offers a greater flexibility. The two models were developed with industrial data...

  17. The Physics of Boiling at Burnout

    Science.gov (United States)

    Theofanous, T. G.; Tu, J. P.; Dinh, T. N.; Salmassi, T.; Dinh, A. T.; Gasljevic, K.

    2000-01-01

    The basic elements of a new experimental approach for the investigation of burnout in pool boiling are presented. The approach consists of the combined use of ultrathin (nano-scale) heaters and high speed infrared imaging of the heater temperature pattern as a whole, in conjunction with highly detailed control and characterization of heater morphology at the nano and micron scales. It is shown that the burnout phenomenon can be resolved in both space and time. Ultrathin heaters capable of dissipating power levels, at steady-state, of over 1 MW/square m are demonstrated. A separation of scales is identified and it is used to transfer the focus of attention from the complexity of the two-phase mixing layer in the vicinity of the heater to a micron-scaled microlayer and nucleation and associated film-disruption processes within it.

  18. Abscisic acid, H2O2 and nitric oxide interactions mediated cold-induced S-adenosylmethionine synthetase in Medicago sativa subsp. falcata that confers cold tolerance through up-regulating polyamine oxidation.

    Science.gov (United States)

    Guo, Zhenfei; Tan, Jiali; Zhuo, Chunliu; Wang, Congying; Xiang, Bin; Wang, Zengyu

    2014-06-01

    S-adenosylmethionine synthetase (SAMS) is the key enzyme catalysing the formation of S-adenosylmethionine (SAM), a precursor of polyamines and ethylene. To investigate the potential role of SAMS in cold tolerance, we isolated MfSAMS1 from the cold-tolerant germplasm Medicago sativa subsp. falcata and analysed the association of SAM-derived polyamines with cold tolerance. The expression of MfSAMS1 in leaves was greatly induced by cold, abscisic acid (ABA), H2O2 and nitric oxide (NO). Our data revealed that ABA, H2O2 and NO interactions mediated the cold-induced MfSAMS1 expression and cold acclimation in falcata. SAM, putrescine, spermidine and spermine levels, ethylene production and polyamine oxidation were sequentially altered in response to cold, indicating that SAMS-derived SAM is preferentially used in polyamine synthesis and homeostasis during cold acclimation. Antioxidant enzyme activities were also induced in response to cold and showed correlation with polyamine oxidation. Overexpression of MfSAMS1 in tobacco resulted in elevated SAM levels, but polyamine levels and ethylene production in the transgenic plants were not significantly changed. Compared to the wild type, transgenic plants had increased levels of apoplastic H2O2, higher transcript levels of genes involved in polyamine synthesis and oxidation, and higher activities of polyamine oxidation and antioxidant enzymes. The results showed that overexpression of MfSAMS1 promoted polyamine synthesis and oxidation, which in turn improved H2 O2 -induced antioxidant protection, as a result enhanced tolerance to freezing and chilling stress in transgenic plants. This is the first report demonstrating that SAMS plays an important role in plant tolerance to cold via up-regulating polyamine oxidation.

  19. Protective role of caffeic acid phenethyl ester and erdosteine on activities of purine-catabolizing enzymes and level of nitric oxide in red blood cells of isoniazid-administered rats.

    Science.gov (United States)

    Yilmaz, H R; Uz, E; Gökalp, O; Ozçelik, N; Ciçek, E; Ozer, M K

    2008-09-01

    The aim of this experimental study was to investigate the possible role of nitric oxide (NO) and the activities of adenosine deaminase (ADA) and xanthine oxidase (XO) in the pathogenesis of isoniazid (INH)-induced oxidative damage in red blood cells (RBCs), and also to show the effect of caffeic acid phenethyl ester (CAPE) and erdosteine, antioxidants, in decreasing this toxicity. A total of 25 adult male rats were divided into four experimental groups as follows: control group (n = 7), INH-treated group (n = 6), INH + CAPE-treated group (n = 6), and INH + erdosteine-treated group (n = 6). INH, INH-CAPE, and INH-erdosteine-treated groups were treated orally with INH 50 mg/kg daily and with the tap water for 15 days. Control group was given only tap water. CAPE was intraperitoneally injected for 15 days at a dose of 10 micromol/kg. Erdosteine was treated orally for 15 days at a dose of 10 mg/kg/day. The injection of INH led to a significant increase in the activities of ADA, XO, and NO levels in RBCs of rats. Co-treatment with CAPE caused a significant decrease in the activities of ADA and XO and the levels of NO in RBCs. In addition, co-treatment with erdosteine caused a significant decrease in the activities of ADA and XO and the levels of NO in RBCs. The results of this study showed that ADA, XO, and NO may play an important role in the pathogenesis of INH-induced oxidative stress in RBCs. CAPE and erdosteine may have protective potential in this process and they may become a promising drug in the prevention of this undesired side effect of INH.

  20. Process for the extraction of strontium from acidic solutions

    Energy Technology Data Exchange (ETDEWEB)

    Horwitz, E.P.; Dietz, M.L.

    1993-01-01

    The invention is a process for selectively extracting strontium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant solution is a macrocyclic polyether in an aliphatic hydrocarbon diluent containing a phase modifier. The process will selectively extract strontium values from nitric acid solutions which are up to 6 molar in nitric acid.

  1. Transition boiling heat transfer and the film transition regime

    Science.gov (United States)

    Ramilison, J. M.; Lienhard, J. H.

    1987-01-01

    The Berenson (1960) flat-plate transition-boiling experiment has been recreated with a reduced thermal resistance in the heater, and an improved access to those portions of the transition boiling regime that have a steep negative slope. Tests have been made in Freon-113, acetone, benzene, and n-pentane boiling on horizontal flat copper heaters that have been mirror-polished, 'roughened', or teflon-coated. The resulting data reproduce and clarify certain features observed by Berenson: the modest surface finish dependence of boiling burnout, and the influence of surface chemistry on both the minimum heat flux and the mode of transition boiling, for example. A rational scheme of correlation yields a prediction of the heat flux in what Witte and Lienhard (1982) previously identified as the 'film-transition boiling' region. It is also shown how to calculate the heat flux at the boundary between the pure-film, and the film-transition, boiling regimes, as a function of the advancing contact angle.

  2. Research progresses and future directions on pool boiling heat transfer

    Directory of Open Access Journals (Sweden)

    M. Kumar

    2015-12-01

    Full Text Available This paper reviews the previous work carried on pool boiling heat transfer during heating of various liquids and commodities categorized as refrigerants and dielectric fluids, pure liquids, nanofluids, hydrocarbons and additive mixtures, as well as natural and synthetic colloidal solutions. Nucleate pool boiling is an efficient and effective method of boiling because high heat fluxes are possible with moderate temperature differences. It is characterized by the growth of bubbles on a heated surface. It occurs during boiling of liquids for excess temperature ranging from 5 to 30 °C in various processes related to high vaporization of liquid for specific purposes like sugarcane juice heating for jaggery making, milk heating for khoa making, steam generation, cooling of electronic equipments, refrigeration and etcetera. In this review paper, pool boiling method during heating of liquids for specific purpose is depicted. It is inferred that enhancement in pool boiling heat transfer is a challenging and complex task. Also, recent research and use of various correlations for natural convection pool boiling is reviewed.

  3. The role of nitric oxide in salicylic acid-induced stomatal movement on the epicarp of Zephyranthes candida%NO在水杨酸诱导葱莲果实上气孔运动中的作用

    Institute of Scientific and Technical Information of China (English)

    余君彤; 杨荞嘉; 鄢思斯; 马三梅; 王永飞

    2013-01-01

    以葱莲外果皮为材料,研究了NO在水杨酸(salicylic acid,SA)诱导葱莲外果皮上气孔运动的作用.结果表明:在一定浓度范围内,单独施用不同浓度的NO和SA均可诱导葱莲外果皮上气孔不同程度的关闭,并且浓度越大,诱导气孔关闭的效应越明显;NO和SA共同施用所诱导气孔关闭的效应大于其单独施用效应;NO的清除剂血红蛋白(hemoglobin,Hb)和硝酸还原酶(nitrate reductase,NR)的抑制剂叠氮化钠(NaN3)能明显削弱SA诱导葱莲外果皮气孔关闭的效应.因此推论,在诱导葱莲果实上气孔运动过程中,NO和SA之间具有协同效应,并且SA通过NR途径诱导产生NO,进而诱导气孔关闭.%Using the epicarp of Zephyranthes candida as the experimental material,the role of nitric oxide in salicylic acid (SA)-induced stomatal movement was studied.The results indicated that within certain range of concentrations,NO and SA could induce various degrees of stomatal closure in dose-dependently.The effects of the mixed solution of NO and SA were greater than those of the individual processing.NO scavenger hemoglobin (Hb) and nitrate reductase (NR) inhibitor sodium azide (NaN3) could weaken the effect of SA significantly.This showed that the stomatal closure could be co-induced by NO and SA,SA may induce NO synthesis through NR path at first and then induce stomatal closure.

  4. Modelado Cinético de la Disolución de Hidroboracita en Soluciones de Ácido Nítrico Kinetics Modeling of Hydroboracite Dissolution in Nitric Acid Solutions

    Directory of Open Access Journals (Sweden)

    Graciela V Morales

    2012-01-01

    Full Text Available Se estudia la cinética de disolución de hidroboracita en soluciones de ácido nítrico, cuyos subproductos, nitrato de calcio y nitrato de magnesio, tienen una importante aplicabilidad comercial como fertilizantes. La disolución se realiza en un reactor tanque agitado discontinuo a presión atmosférica. S e investigan los efectos que tienen los factores temperatura, tamaño de partícula, relación sólido/líquido y concentración de ácido, sobre la velocidad de disolución; y se evalúan los parámetros cinéticos: factor de frecuencia y energía de activación. S e observa que la velocidad de disolución crece con el aumento de la temperatura, la disminución del tamaño de partícula, y con la disminución de la relación sólido/líquido. Se observa, también, que un aumento en la concentración del ácido nítrico hace aumentar, siempre, el grado de disolución. Se determina que la energía de activación aparente es del orden de 13 kJ/mol, siendo la disolución de la hidroboracita en ácido nítrico controlada por mecanismos difusivos .The dissolution kinetics of hydroboracite in nitric acid solutions, whose products, calcium nitrate and magnesium nitrate have important commercial applications as fertilizer was studied. The dissolution was carried out in a batch reactor at atmospheric pressure. The effects of the temperature, particle size, solid/liquid ratio and concentration of solution on the dissolution rate were investigated, and the kinetic parameters: frequency factor and activation energy were evaluated. It was found that the dissolution rate increased when the reaction temperature increased and when the particle size decreases. The dissolution rate decreases when the solid/liquid ratio increases. It was also found that an increasing in the acid concentration always increases the dissolution mineral rate. It was determined that the dissolution rate fit well to the diffusive control model and the activation energy of this

  5. Thermodynamic modelling of the extraction of nitrates of lanthanides by CMPO and by CMPO-like calixarene in concentrated nitric acid medium. Application in the optimization of the separation of lanthanides and actinides/lanthanides; Modelisation thermodynamique de l'extraction de nitrates de lanthanides par le CMPO et par un calixarene-CMPO en milieu acide nitrique concentre. Application a l'optimisation de la separation des lanthanides et des actinides/lanthanides

    Energy Technology Data Exchange (ETDEWEB)

    Belair, S

    2003-07-01

    The separation minor actinides / lanthanides in nitric acid medium is as one of problems of separative chemistry the most delicate within the framework of the processes allowing the recovery of long life radioelements present in the solutions of fission products. Previous studies showed that CMPO-substituted calix[4]arenes presents a better affinity for actinides than for lanthanides. To optimize the operating conditions of separation and to take into account the degree of non-ideality for the concentrated nitric solutions, we adopted a thermodynamic approach. The methodology taken to determine the number and the stoichiometry of the complexes formed in organic phase base on MIKULIN-SERGIEVSKII's model used through a software of data processing of experimental extraction isotherms. These tools are exploited at first on an extraction system engaging the CMPO, extractant reagent of actinides and lanthanides in concentrated nitric medium. The modelling of the system Ln(NO{sub 3}){sub 3}-HNO{sub 3}-H{sub 2}O/CMPO comes to confirm the results of several studies. At the same time, they allow to establish working hypotheses aiming at limiting the investigations of our researches towards the most stable complexes formed between lanthanides and CMPO-like calixarene to which the same method is then applied. An analytical expression of the selectivity of separation by the calixarene is established to determine the parameters and physico-chemical variables on which it depends. So, the ratio of the constants of extraction and the value of the activity of water of the system fixes the selectivity of separation of 2 elements. The exploitation of this relation allows to preview the influence of a variation of the concentration of nitric acid. Experiments of extraction confirm these forecasts and inform about the affinity of the calixarene with respect to lanthanides elements and to the americium. (author)

  6. Modeling of Heat Exchange with Developed Nucleate Boiling on Tenons

    Directory of Open Access Journals (Sweden)

    A. V. Оvsiannik

    2007-01-01

    Full Text Available The paper proposes a thermal and physical model for heat exchange processes with developed nucleate boiling on the developed surfaces (tenons with various contours of heat transfer surface. Dependences for calculating convective heat exchange factor have been obtained on the basis of modeling representation. Investigations have shown that an intensity of convective heat exchange does not depend on tenon profile when boiling takes place on the tenons. The intensity is determined by operating conditions, thermal and physical properties of liquid, internal characteristics of boiling processes and geometrical characteristics of a tenon.

  7. Boiling Heat Transfer on Porous Surfaces with Vapor Channels

    Institute of Scientific and Technical Information of China (English)

    吴伟; 杜建华; 王补宣

    2002-01-01

    Boiling heat transfer on porous coated surfaces with vapor channels was investigated experimentally to determine the effects of the size and density of the vapor channels on the boiling heat transfer. Observations showed that bubbles escaping from the channels enhanced the heat transfer. Three regimes were identified: liquid flooding, bubbles in the channel and the bottom drying out region. The maximum heat transfer occurred for an optimum vapor channel density and the boiling heat transfer performance was increased if the channels were open to the bottom of the porous coating.

  8. Experimental study on the explosive boiling in saturated liquid nitrogen

    Institute of Scientific and Technical Information of China (English)

    DONG Zhaoyi; HUAI Xiulan; LIU Dengying

    2005-01-01

    Studies on the heat-transfer characteristics of liquid nitrogen (LN2) have received increasing attention. When there is a transient high heatflux input to the LN2, explosive boiling may take place. In this paper, using the high-power short-duration pulsed laser heating method and the high-speed photography technology, the experimental result of explosive boiling in saturated LN2 is illustrated; and the two exclusive characteristics of explosive boiling in LN2: changeover time and the relative long-time adherence of the bubble cluster to the surface, are investigated.

  9. Subcooled boiling of nano-particle suspensions on Pt wires

    Institute of Scientific and Technical Information of China (English)

    LI Chunhui; WANG Buxuan; PENG Xiaofeng

    2004-01-01

    An experimental investigation is conducted to explore the subcooled boiling characteristics of nano-particle suspensions on Pt wires. Some phenomena are observed for the boiling of water-SiO2 nano-particle suspensions on Pt wires. The experiments show that there exist not any evident differences for boiling of pure water and of nano-particle suspensions at high heat fluxes. However, bubble overlap phenomenon can be easily found for nano-particle suspensions at low heat fluxes, which probably results from the increase of the attracter force between bubbles and of the bubble mass.

  10. Bubble Coalescence Heat Transfer During Subcooled Nucleate Pool Boiling

    Institute of Scientific and Technical Information of China (English)

    Abdoulaye Coulibaly; LIN Xipeng; Bi Jingliang; David M Christopher

    2012-01-01

    Bubble coalescence during subcooled nucleate pool boiling was investigated experimentally using constant wall temperature boundary conditions while the wall heat flux was measured at a various locations to understand the effects of coalescence on the heat transfer. The observations showed that the coalesced bubble moved and oscillated on the heater surface with significant heat transfer variations prior to departure. Some observations also showed coalescence with no increase in the heat transfer rate. The heat flux for boiling with coalescence fluctuated much more than for single bubble boiling due to the vaporization of the liquid layer trapped between the bubbles.

  11. Optimization of Quick-boiling Process for Lotus Root Slices%藕片水焯工艺优化

    Institute of Scientific and Technical Information of China (English)

    计红芳; 张令文; 杨铭铎; 李光磊; 蔡振林

    2011-01-01

    Lotus root slices was quick boiled in four different media such as water,acetic acid,sodium chloride and sodium bicarbonate solution and as a result,acetic acid was identified as the best medium through comprehensive considering VC content and sensory score of quick-boiled lotus root slices as well as dry matter dissolution rate.Further,on the basis of one-factor-at-a-time experiments,Box-Behnken design combined with response surface methodology was used to optimize process conditions for the quick boiling of lotus root slices in acetic acid.The results indicated that the optimal quick boiling conditions were acetic acid concentration of 0.35%,temperature of 68.4 ℃ and quick-boiling time of 2.4 min.After quick boiling under the optimal process conditions,the content of vitamin C in lotus root slices was 30.185 mg/100 g fresh weight,and better eating quality was also achieved.The results of variance analysis showed that acetic acid concentration,quick-boiling temperature and quick-boiling time had significant effects on the content of vitamin C in quick-boiled lotus root slices(P0.01).Moreover,the cross-interactions between acetic acid concentration and temperature and between temperature and quick-boiling time also revealed a significant effect on the content of vitamin C in lotus root slices(P0.05).%以新鲜莲藕为试验材料,对水、乙酸溶液、食盐溶液和碳酸氢钠溶液等4种水焯介质进行探讨;通过单因素试验和Box-Behnken设计及响应面分析法,对藕片水焯的最佳工艺条件进行研究。结果表明:乙酸可作为藕片的水焯介质;藕片水焯的最佳工艺条件为乙酸体积分数0.35%、温度68.4℃、时间2.4min,在该条件下藕片中VC含量为30.185mg/100g,干物质溶出率为5.384%,藕片食用品质可达到较高水平。响应面方差分析结果显示,乙酸体积分数、温度和水焯时间对水焯藕片VC含量有显著影响(P〈0.01),乙酸体积分数和温度、温度和

  12. Nitric oxide and cardiovascular system.

    Science.gov (United States)

    Cengel, Atiye; Sahinarslan, Asife

    2006-12-01

    Endothelium has many important functions including the control of blood-tissue permeability and vascular tonus, regulation of vascular surface properties for homeostasis and inflammation. Nitric oxide is the chief molecule in regulation of endothelial functions. Nitric oxide deficiency, which is also known as endothelial dysfunction, is the first step for the occurrence of many disease states in cardiovascular system including heart failure, hypertension, dyslipidemia, insulin resistance, diabetes mellitus, hyperhomocysteinemia and smoking. This review deals with the importance of nitric oxide for cardiovascular system. It also includes the latest improvements in the diagnosis and treatment of endothelial dysfunction.

  13. 49 CFR 173.337 - Nitric oxide.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Nitric oxide. 173.337 Section 173.337... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.337 Nitric oxide. (a) Nitric oxide must be... valve and valve seat that will not deteriorate in contact with nitric oxide. Cylinders or valves may...

  14. Impact of different wort boiling temperatures on the beer foam stabilizing properties of lipid transfer protein 1.

    Science.gov (United States)

    Van Nierop, Sandra N E; Evans, David E; Axcell, Barry C; Cantrell, Ian C; Rautenbach, Marina

    2004-05-19

    Beer consumers demand satisfactory and consistent foam stability; thus, it is a high priority for brewers. Beer foam is stabilized by the interaction between certain beer proteins, including lipid transfer protein 1 (LTP1), and isomerized hop alpha-acids, but destabilized by lipids. In this study it was shown that the wort boiling temperature during the brewing process was critical in determining the final beer LTP1 content and conformation. LTP1 levels during brewing were measured by an LTP1 ELISA, using antinative barley LTP1 polyclonal antibodies. It was observed that the higher wort boiling temperatures ( approximately 102 degrees C), resulting from low altitude at sea level, reduced the final beer LTP1 level to 2-3 microg/mL, whereas the lower wort boiling temperatures ( approximately 96 degrees C), resulting from higher altitudes (1800 m), produced LTP1 levels between 17 and 35 microg/mL. Low levels of LTP1 in combination with elevated levels of free fatty acids (FFA) resulted in poor foam stability, whereas beer produced with low levels of LTP1 and FFA had satisfactory foam stability. Previous studies indicated the need for LTP1 denaturing to improve its foam stabilizing properties. However, the results presented here show that LTP1 denaturation reduces its ability to act as a binding protein for foam-damaging FFA. These investigations suggest that wort boiling temperature is an important factor in determining the level and conformation of LTP1, thereby favoring satisfactory beer foam stability.

  15. Antioxidant Capacity and Phenolic Content in Olive Leaf Tisane as Affected by Boiling Treatment

    Directory of Open Access Journals (Sweden)

    Fathia AOUIDI

    2016-06-01

    Full Text Available This paper investigated the effect of preparation method on the quality of olive leaf tisane. Secondly, it aimed at evaluating and understanding the effect of boiling treatment on phenolic compounds and antioxidant capacity of an aqueous extract of olive leaves. The Phenolic content was determined by Folin-Ciocalteu method. The antioxidant capacity was assessed by ABTS+ method. The Phenolic content and antioxidant capacity depended on extraction procedure of olive leaf tisane. It was found that boiling leads to a decrease in the phenolic content and a rise of antioxidant capacity of aqueous extract from olive leaves. The mass molecular distribution of the polymeric aromatic fraction was analyzed by gel filtration chromatography on Sephadex G50. Results suggested the hydrolysis of phenolic polymers following boiling. Moreover, HPLC analyses showed an increase in rutin, oleuropein and caffeic acid levels in treated sample. As a conclusion, thermal processing could be useful for enhancing the antioxidant capacity and the extractability of phenolic compounds in olive leaf tisane.

  16. Production of tyramine by Enterococcus faecalis strains in water-boiled salted duck.

    Science.gov (United States)

    Liu, Fang; Du, Lihui; Xu, Weiyan; Wang, Daoying; Zhang, Muhan; Zhu, Yongzhi; Xu, Weimin

    2013-05-01

    The potential to produce biogenic amines was investigated with 15 Lactococcus lactis and 15 Enterococcus faecalis strains isolated from water-boiled salted duck. The production of biogenic amines from the isolated strains grown in de Man Rogosa Sharpe broth containing precursor amino acids was determined by thin-layer chromatography and high-performance liquid chromatography. None of the L. lactis strains produced any biogenic amines, whereas 12 strains of E. faecalis produced tyramine and b -phenylethylamine. PCR assays were used to detect the presence of tyrosine decarboxylase genes in all of the isolated strains. Only the 12 biogenic amine-producing Enterococcus strains had a 924-bp fragment characteristic for the tyrosine decarboxylase gene. The comparison of the amplified partial tyrDC gene sequences of the 12 positive Enterococcus strains revealed 99% similarity within the same species. The tyramine production of the sterilized water-boiled salted duck inoculated with E. faecalis R612Z1 increased significantly during storage. This study reveals that the isolated E. faecalis strains can produce tyramine and β-phenylethylamine in the medium; however, they can only produce tyramine in water-boiled salted duck.

  17. Visualization of boiling flow structure in a natural circulation boiling loop

    Energy Technology Data Exchange (ETDEWEB)

    Karmakar, Arnab; Paruya, Swapan, E-mail: swapanparuya@gmail.com

    2015-04-15

    Highlights: • Vapor–liquid jet flows in natural circulation boiling loop. • Flow patterns and their transitions during geysering instability in the loop. • Evaluation of the efficiency of the needle probe in detecting the vapor–liquid and boiling flow structure. - Abstract: The present study reports vapor–liquid jet flows, flow patterns and their transitions during geysering instability in a natural circulation boiling loop under varied inlet subcooling ΔT{sub sub} (30–50 °C) and heater power Q (4–5 kW). Video imaging, voltage measurement using impedance needle probe, measurement of local pressure and loop flow rate have been carried out in this study. Power spectra of the voltage, the pressure and the flow rate reveal that at a high ΔT{sub sub} the jet flows have long period (21.36–86.95 s) and they are very irregular with a number of harmonics. The period decreases and becomes regular with a decrease of ΔT{sub sub}. The periods of the jet flows at ΔT{sub sub} = 30–50 °C and Q = 4 kW are in close agreement with those obtained from the video imaging. The probe was found to be more efficient than the pressure sensor in detecting the jet flows within an uncertainty of 9.5% and in detecting a variety of bubble classes. Both the imaging and the probe consistently identify the bubbly flow/vapor-mushrooms transition or the bubbly flow/slug flow transition on decreasing ΔT{sub sub} or on increasing Q.

  18. Self-Sustaining Thorium Boiling Water Reactors

    Directory of Open Access Journals (Sweden)

    Ehud Greenspan

    2012-10-01

    Full Text Available A thorium-fueled water-cooled reactor core design approach that features a radially uniform composition of fuel rods in stationary fuel assembly and is fuel-self-sustaining is described. This core design concept is similar to the Reduced moderation Boiling Water Reactor (RBWR proposed by Hitachi to fit within an ABWR pressure vessel, with the following exceptions: use of thorium instead of depleted uranium for the fertile fuel; elimination of the internal blanket; and elimination of absorbers from the axial reflectors, while increasing the length of the fissile zone. The preliminary analysis indicates that it is feasible to design such cores to be fuel-self-sustaining and to have a comfortably low peak linear heat generation rate when operating at the nominal ABWR power level of nearly 4000 MWth. However, the void reactivity feedback tends to be too negative, making it difficult to have sufficient shutdown reactivity margin at cold zero power condition. An addition of a small amount of plutonium from LWR used nuclear fuel was found effective in reducing the magnitude of the negative void reactivity effect and enables attaining adequate shutdown reactivity margin; it also flattens the axial power distribution. The resulting design concept offers an efficient incineration of the LWR generated plutonium in addition to effective utilization of thorium. Additional R&D is required in order to arrive at a reliable practical and safe design.

  19. Zero Boil Off System for Cryogen Storage Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This work proposes to develop a zero boil off (ZBO) dewar using a two-stage pulse-tube cooler together with two innovative, continuous-flow cooling loops and an...

  20. Boiling local heat transfer enhancement in minichannels using nanofluids.

    Science.gov (United States)

    Chehade, Ali Ahmad; Gualous, Hasna Louahlia; Le Masson, Stephane; Fardoun, Farouk; Besq, Anthony

    2013-03-18

    This paper reports an experimental study on nanofluid convective boiling heat transfer in parallel rectangular minichannels of 800 μm hydraulic diameter. Experiments are conducted with pure water and silver nanoparticles suspended in water base fluid. Two small volume fractions of silver nanoparticles suspended in water are tested: 0.000237% and 0.000475%. The experimental results show that the local heat transfer coefficient, local heat flux, and local wall temperature are affected by silver nanoparticle concentration in water base fluid. In addition, different correlations established for boiling flow heat transfer in minichannels or macrochannels are evaluated. It is found that the correlation of Kandlikar and Balasubramanian is the closest to the water boiling heat transfer results. The boiling local heat transfer enhancement by adding silver nanoparticles in base fluid is not uniform along the channel flow. Better performances and highest effect of nanoparticle concentration on the heat transfer are obtained at the minichannels entrance.

  1. Boiling of HFE-7100 on a Straight Pin Fin

    Institute of Scientific and Technical Information of China (English)

    Z. W. Liu; W.W. Lin; D.J. Lee; J.P. Hsu

    2001-01-01

    This paper deals with an experimental investigation of pin fin boiling of saturated and subcooled HFE-7100 under atmospheric pressure. Fin base temperature and heat flux data are measured along with the fin tip temperature. The basic features of boiling stability of HFE-7100 boiling on pin fin had been reported for the first time. For a given liquid/heating surface combination there exist upper steady-state (USS) branch and lower steady-state (LSS)branch, and a large, unstable regime located in between. Zones with different stability characteristics are mapped according to boiling on fins with different aspect ratios. Liquid subcooling can largely enhance heat transfer performance. A longer fin can provide a safer operation.

  2. An Analytical Approach for Relating Boiling Points of Monofunctional Organic Compounds to Intermolecular Forces

    Science.gov (United States)

    Struyf, Jef

    2011-01-01

    The boiling point of a monofunctional organic compound is expressed as the sum of two parts: a contribution to the boiling point due to the R group and a contribution due to the functional group. The boiling point in absolute temperature of the corresponding RH hydrocarbon is chosen for the contribution to the boiling point of the R group and is a…

  3. Redox iodine and nitric acid absorbers

    Energy Technology Data Exchange (ETDEWEB)

    Stoker, D.J.; Rohrmann, C.A.

    1955-08-02

    A desirable radio-iodine emission goal for all HAPO has recently been set at one curie per day maximum. At the same time it was suggested that a more relaxed limit of ten curries per week with no more than three in any one day, would probably be satisfactory. To assure the achievement of these goal figures in the separations plants it was deemed necessary to either cool'' the irradiated material a greater length of time than is presently done before processing, or provide more efficient, iodine retention facilities. Increased power levels, higher production rates, and an increase in the awareness of radio-iodine emissions, have all coupled together to make present facilities generally inadequate when processing material aged less than about 100 days. Several alternate methods of providing additional iodine retention facilities for Redox were preliminarily scoped and presented for consideration. The purpose of this report is to present a scope design for improving iodine emission control at Redox.

  4. Heat transfer and pressure drop in flow boiling in microchannels

    CERN Document Server

    Saha, Sujoy Kumar

    2016-01-01

    This Brief addresses the phenomena of heat transfer and pressure drop in flow boiling in micro channels occurring in high heat flux electronic cooling. A companion edition in the Springer Brief Subseries on Thermal Engineering and Applied Science to “Critical Heat Flux in Flow Boiling in Micro channels,” by the same author team, this volume is idea for professionals, researchers and graduate students concerned with electronic cooling.

  5. Taylor stability of viscous fluids with application to film boiling

    Science.gov (United States)

    Dhir, V. K.; Lienhard, J. H.

    1973-01-01

    The dispersion relation is evaluated numerically for Taylor waves in a viscous unstable interface with surface tension. The solution takes account of transverse curvature and the numerical evaluations apply to horizontal cylindrical, as well as to plane, interfaces. The result is verified with frequency and wavelength data obtained during film boiling on horizontal wires. A very general empirical correlation is given, en passant, for the vapor blanket thickness during film boiling.

  6. Correlations estimate volume distilled using gravity, boiling point

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, A.; Consuelo Perez de Alba, M. del; Manriquez, L.; Guardia Mendoz, P. de la [Inst. Mexicano del Petroleo, Mexico City (Mexico)

    1995-10-23

    Mathematical nd graphic correlations have been developed for estimating cumulative volume distilled as a function of crude API gravity and true boiling point (TBP). The correlations can be used for crudes with gravities of 21--34{degree} API and boiling points of 150--540 C. In distillation predictions for several mexican and Iraqi crude oils, the correlations have exhibited accuracy comparable to that of laboratory measurements. The paper discusses the need for such a correlation and the testing of the correlation.

  7. Mass concentration and ion composition of coarse and fine particles in an urban area in Beirut: effect of calcium carbonate on the absorption of nitric and sulfuric acids and the depletion of chloride

    Directory of Open Access Journals (Sweden)

    H. Kouyoumdjian

    2006-01-01

    Full Text Available Levels of coarse (PM10-2.5 and fine (PM2.5 particles were determined between February 2004 and January 2005 in the city of Beirut, Lebanon. While low PM mass concentrations were measured in the rainy season, elevated levels were detected during sand storms originating from Arabian desert and/or Africa. Using ATR-FTIR and IC, it was shown that nitrate, sulfate, carbonate and chloride were the main anionic constituents of the coarse particles, whereas sulfate was mostly predominant in the fine particles in the form of (NH42SO4. Ammonium nitrate was not expected to be important because the medium was defined as ammonium poor. In parallel, the cations Ca2+ and Na+ dominated in the coarse, and NH4+, Ca2+ and Na+ in the fine particles. Coarse nitrate and sulfate ions resulted from the respective reactions of nitric and sulfuric acid with a relatively high amount of calcium carbonate. Both CaCO3 and Ca(NO32 crystals identified by ATR-FTIR in the coarse particles were found to be resistant to soaking in water for 24 h but became water soluble when they were formed in the fine particles suggesting, thereby, different growth and adsorption phenomena. The seasonal variational study showed that nitrate and sulfate ion concentrations increased in the summer due to the enhancement of photochemical reactions which facilitated the conversion of NO2 and SO2 gases into NO3- and SO42-, respectively. While nitrate was mainly due to local heavy traffic, sulfates were due to local and long-range transport phenomena. Using the air mass trajectory HYSPLIT model, it was found that the increase in the sulfate concentration correlated with wind vectors coming from Eastern and Central Europe. Chloride levels, on the other hand, were high when wind originated from the sea and low during sand storms. In addition to sea salt, elevated levels of chloride were also attributed to waste mass burning in proximity to the site. In comparison to other neighboring Mediterranean

  8. Electrohydrodynamics of boiling on microstructured surfaces for space applications

    Science.gov (United States)

    Saccone, Giacomo; Moran, Jeffrey L.; Bucci, Matteo; Buongiorno, Jacopo; di Marco, Paolo; Mit-Nuclear Science; Engineering Team; University Of Pisa-Destec Dept. Team

    2016-11-01

    Surface wettability is a major parameter in boiling heat transfer. It affects the departure of bubbles from the boiling surface and consequently determines the maximum heat flux transferrable in safe conditions, known as critical heat flux (CHF). Surface wettability can be enhanced through passive techniques, including micro-engineered surfaces and coatings, or through active techniques, e.g. by applying a tunable electric field (electrowetting) that modifies the bubble shape in such a way as to drive bubble detachment. The latter technique is particularly interesting for space applications, where the electric field is used to create a body force that compensates for the absence of gravity. The present work is focused on boiling heat transfer on surfaces whose wettability has been modified by passive and active techniques. We have built a pool boiling apparatus composed of a micro-structured heater acting as boiling surface and an axisymmetric electrode High-speed optical and infrared imaging have been used to investigate the dynamics of boiling phenomena. The aims of this project are twofold: to achieve a superior understanding of wetting phenomena, and to improve the efficiency of cooling devices for space applications.

  9. Citric Acid Passivation of Stainless Steel

    Science.gov (United States)

    Yasensky, David; Reali, John; Larson, Chris; Carl, Chad

    2009-01-01

    Passivation is a process for cleaning and providing corrosion protection for stainless steel. Currently, on Kennedy Space Center (KSC), only parts passivated with nitric acid are acceptable for use. KSC disposes of approximately 125gal of concentrated nitric acid per year, and receives many parts from vendors who must also dispose of used nitric acid. Unfortunately, nitric acid presents health and environmental hazards. As a result, several recent industry studies have examined citric acid as an alternative. Implementing a citric acid-based passivation procedure would improve the health and environmental safety aspects of passivation process. However although there is a lack of published studies that conclusively prove citric acid is a technically sound passivation agent. In 2007, NASA's KSC Materials Advisory Working Group requested the evaluation of citric acid in place of nitric acid for passivation of parts at KSC. United Space Alliance Materials & Processes engineers have developed a three-phase test plan to evaluate citric acid as an alternative to nitric acid on three stainless steels commonly used at KSC: UNS S30400, S41000, and S17400. Phases 1 and 2 will produce an optimized citric acid treatment based on results from atmospheric exposure at NASA's Beach Corrosion Facility. Phase 3 will compare the optimized solution(s) with nitric acid treatments. If the results indicate that citric acid passivates as well or better than nitric acid, NASA intends to approve this method for parts used at the Kennedy Space Center.

  10. Void fraction prediction in saturated flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Francisco J Collado [Dpto de Ingenieria Mecanica-Motores Termicos, CPS-B, Universidad de Zaragoza, Maria de Luna 50018-Zaragoza (Spain)

    2005-07-01

    Full text of publication follows: An essential element in thermal-hydraulics is the accurate prediction of the vapor void fraction, or fraction of the flow cross-sectional area occupied by steam. Recently, the author has suggested to calculate void fraction working exclusively with thermodynamic properties. It is well known that the usual 'flow' quality, merely a mass flow rate ratio, is not at all a thermodynamic property because its expression in function of thermodynamic properties includes the slip ratio, which is a parameter of the process not a function of state. By the other hand, in the classic and well known expression of the void fraction - in function of the true mass fraction of vapor (also called 'static' quality), and the vapor and liquid densities - does not appear the slip ratio. Of course, this would suggest a direct procedure for calculating the void fraction, provided we had an accurate value of the true mass fraction of vapor, clearly from the heat balance. However the classic heat balance is usually stated in function of the 'flow' quality, what sounds really contradictory because this parameter, as we have noted above, is not at all a thermodynamic property. Then we should check against real data the actual relationship between the thermodynamic properties and the applied heat. For saturated flow boiling just from the inlet of the heated tube, and not having into account the kinetic and potential terms, the uniform applied heat per unit mass of inlet water and per unit length (in short, specific linear heat) should be closely related to a (constant) slope of the mixture enthalpy. In this work, we have checked the relation between the specific linear heat and the thermodynamic enthalpy of the liquid-vapor mixture using the actual mass fraction. This true mass fraction is calculated using the accurate measurements of the outlet void fraction taken during the Cambridge project by Knights and Thom in the sixties for

  11. Nitric oxide and pH modulation in gynaecological cancer.

    Science.gov (United States)

    Sanhueza, Carlos; Araos, Joaquín; Naranjo, Luciano; Barros, Eric; Subiabre, Mario; Toledo, Fernando; Gutiérrez, Jaime; Chiarello, Delia I; Pardo, Fabián; Leiva, Andrea; Sobrevia, Luis

    2016-12-01

    Nitric oxide plays several roles in cellular physiology, including control of the vascular tone and defence against pathogen infection. Neuronal, inducible and endothelial nitric oxide synthase (NOS) isoforms synthesize nitric oxide. Cells generate acid and base equivalents, whose physiological intracellular concentrations are kept due to membrane transport systems, including Na(+) /H(+) exchangers and Na(+) /HCO3(-) transporters, thus maintaining a physiological pH at the intracellular (~7.0) and extracellular (~7.4) medium. In several pathologies, including cancer, cells are exposed to an extracellular acidic microenvironment, and the role for these membrane transport mechanisms in this phenomenon is likely. As altered NOS expression and activity is seen in cancer cells and because this gas promotes a glycolytic phenotype leading to extracellular acidosis in gynaecological cancer cells, a pro-inflammatory microenvironment increasing inducible NOS expression in this cell type is feasible. However, whether abnormal control of intracellular and extracellular pH by cancer cells regards with their ability to synthesize or respond to nitric oxide is unknown. We, here, discuss a potential link between pH alterations, pH controlling membrane transport systems and NOS function. We propose a potential association between inducible NOS induction and Na(+) /H(+) exchanger expression and activity in human ovary cancer. A potentiation between nitric oxide generation and the maintenance of a low extracellular pH (i.e. acidic) is proposed to establish a sequence of events in ovarian cancer cells, thus preserving a pro-proliferative acidic tumour extracellular microenvironment. We suggest that pharmacological therapeutic targeting of Na(+) /H(+) exchangers and inducible NOS may have benefits in human epithelial ovarian cancer.

  12. Heat transfer mechanisms in microgravity flow boiling.

    Science.gov (United States)

    Ohta, Haruhiko

    2002-10-01

    The objective of this paper is to clarify the mechanisms of heat transfer and dryout phenomena in flow boiling under microgravity conditions. Liquid-vapor behavior in annular flow, encountered in the moderate quality region, has extreme significance for practical application in space. To clarify the gravity effect on the heat transfer observed for an upward flow in a tube, the research described here started from the measurement of pressure drop for binary gas-liquid mixture under various gravity conditions. The shear stress acting on the surface of the annular liquid film was correlated by an empirical method. Gravity effects on the heat transfer due to two-phase forced convection were investigated by the analysis of velocity and temperature profiles in the film. The results reproduce well the trends of heat transfer coefficients varying with the gravity level, quality, and mass velocity. Dryout phenomena in the moderate quality region were observed in detail by the introduction of a transparent heated tube. At heat fluxes just lower and higher than CHF value, a transition of the heat transfer coefficient was calculated from oscillating wall temperature, where a series of opposing heat transfer trends--the enhancement due to the quenching of dried areas or evaporation from thin liquid films and the deterioration due to the extension of dry patches--were observed between the passage of disturbance waves. The CHF condition that resulted from the insufficient decrease of wall temperature in the period of enhanced heat transfer was overcome by a temperature increase in the deterioration period. No clear effect of gravity on the mechanisms of dryout was observed within the range of experiments.

  13. Experimental Investigation on the Effects of Coolant Concentration on Sub-Cooled Boiling and Crud Deposition on Reactor Cladding at Prototypical PWR Operating Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Schultis, J., Kenneth; Fenton, Donald, L.

    2006-10-20

    Increasing demand for energy necessitates nuclear power units to increase power limits. This implies significant changes in the design of the core of the nuclear power units, therefore providing better performance and safety in operations. A major hindrance to the increase of nuclear reactor performance especially in Pressurized Deionized water Reactors (PWR) is Axial Offset Anomaly (AOA)--the unexpected change in the core axial power distribution during operation from the predicted distribution. This problem is thought to be occur because of precipitation and deposition of lithiated compounds like boric acid (H{sub 2}BO{sub 3}) and lithium metaborate (LiBO{sub 2}) on the fuel rod cladding. Deposited boron absorbs neutrons thereby affecting the total power distribution inside the reactor. AOA is thought to occur when there is sufficient build-up of crud deposits on the cladding during subcooled nucleate boiling. Predicting AOA is difficult as there is very little information regarding the heat and mass transfer during subcooled nucleate boiling. An experimental investigation was conducted to study the heat transfer characteristics during subcooled nucleate boiling at prototypical PWR conditions. Pool boiling tests were conducted with varying concentrations of lithium metaborate (LiBO{sub 2}) and boric acid (H{sub 2}BO{sub 3}) solutions in deionized water. The experimental data collected includes the effect of coolant concentration, subcooling, system pressure and heat flux on pool the boiling heat transfer coefficient. The analysis of particulate deposits formed on the fuel cladding surface during subcooled nucleate boiling was also performed. The results indicate that the pool boiling heat transfer coefficient degrades in the presence of boric acid and lithium metaborate compared to pure deionized water due to lesser nucleation. The pool boiling heat transfer coefficients decreased by about 24% for 5000 ppm concentrated boric acid solution and by 27% for 5000 ppm

  14. Prediction of (195) Pt NMR chemical shifts of dissolution products of H2 [Pt(OH)6 ] in nitric acid solutions by DFT methods: how important are the counter-ion effects?

    Science.gov (United States)

    Tsipis, Athanassios C; Karapetsas, Ioannis N

    2016-08-01

    (195) Pt NMR chemical shifts of octahedral Pt(IV) complexes with general formula [Pt(NO3 )n (OH)6 - n ](2-) , [Pt(NO3 )n (OH2 )6 - n ](4 - n) (n = 1-6), and [Pt(NO3 )6 - n  - m (OH)m (OH2 )n ](-2 + n - m) formed by dissolution of platinic acid, H2 [Pt(OH)6 ], in aqueous nitric acid solutions are calculated employing density functional theory methods. Particularly, the gauge-including atomic orbitals (GIAO)-PBE0/segmented all-electron relativistically contracted-zeroth-order regular approximation (SARC-ZORA)(Pt) ∪ 6-31G(d,p)(E)/Polarizable Continuum Model computational protocol performs the best. Excellent second-order polynomial plots of δcalcd ((195) Pt) versus δexptl ((195) Pt) chemical shifts and δcalcd ((195) Pt) versus the natural atomic charge QPt are obtained. Despite of neglecting relativistic and spin orbit effects the good agreement of the calculated δ (195) Pt chemical shifts with experimental values is probably because of the fact that the contribution of relativistic and spin orbit effects to computed σ(iso) (195) Pt magnetic shielding of Pt(IV) coordination compounds is effectively cancelled in the computed δ (195) Pt chemical shifts, because the relativistic corrections are expected to be similar in the complexes and the proper reference standard used. To probe the counter-ion effects on the (195) Pt NMR chemical shifts of the anionic [Pt(NO3 )n (OH)6 - n ](2-) and cationic [Pt(NO3 )n (OH2 )6 - n ](4 - n) (n = 0-3) complexes we calculated the (195) Pt NMR chemical shifts of the neutral (PyH)2 [Pt(NO3 )n (OH)6 - n ] (n = 1-6; PyH = pyridinium cation, C5 H5 NH(+) ) and [Pt(NO3 )n (H2 O)6 - n ](NO3 )4 - n (n = 0-3) complexes. Counter-anion effects are very important for the accurate prediction of the (195) Pt NMR chemical shifts of the cationic [Pt(NO3 )n (OH2 )6 - n ](4 - n) complexes, while counter-cation effects are less important for the anionic [Pt(NO3 )n (OH)6

  15. Inspection of Pool Boiling with Superhydrophilic and Superhydrophobic Coating

    Energy Technology Data Exchange (ETDEWEB)

    Son, Gyumin; Moon, Sung Bo; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of)

    2015-05-15

    In conventional nuclear power plants, increasing critical heat flux (CHF) margin by converting existing parts is economically meaningful since it means overall energy production increase without building additional power plants. There were researches to enhance margin from the very beginning of the commercialization of nuclear power plants and many efforts have led to current model of plants, optimized for both safety and production efficiency. Examples are mixing vane which is actually applied to plants nowadays, using nanofluids to enhance heat transfer coefficient (HTC), trying porous surfaces and so on. Takata et al. studied effects of surface wettability by using hydrophobic coating and observed enhanced nucleate boiling at coated surface regions. Betz et al. experimented superhydrophilic (SHPi), superhydrophobic (SHPo), and superbiphilic surfaces. Results indicate heat transfer coefficient enhancement due to increase of nucleation sites by hydrophobic regions and constrained diameter of growing bubbles by hydrophilic regions. Although it would be rough to apply their concept to real reactor coolant surface wall, understanding the possibility of enhanced boiling is meaningful. In this paper, SHPi and SHPo coatings were applied to wire at traditional pool boiling experiment by Nukiyama. By observing altered CHF margin and nucleate boiling, the effects of each coating and their tendencies are discussed. SHPi, SHPo and bare wire's pool boiling was investigated and their boiling graphs were discussed. SHPi shows enhancement in CHF while SHPo's case is more complicated since there were variables like partial CHF or micro scale bubbles. Additional experiment could be comparing HTC, checking whether hydrophobic wire's nucleate boiling enhancement can exceed the decreased CHF margin. More sophisticated method to remove unwanted bubbles should be considered such as using degassed water.

  16. Study of film boiling collapse behavior during vapor explosion

    Energy Technology Data Exchange (ETDEWEB)

    Yagi, Masahiro; Yamano, Norihiro; Sugimoto, Jun [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Abe, Yutaka; Adachi, Hiromichi; Kobayashi, Tomoyoshi

    1996-06-01

    Possible large scale vapor explosions are safety concern in nuclear power plants during severe accident. In order to identify the occurrence of the vapor explosion and to estimate the magnitude of the induced pressure pulse, it is necessary to investigate the triggering condition for the vapor explosion. As a first step of this study, scooping analysis was conducted with a simulation code based on thermal detonation model. It was found that the pressure at the collapse of film boiling much affects the trigger condition of vapor explosion. Based on this analytical results, basic experiments were conducted to clarify the collapse conditions of film boiling on a high temperature solid ball surface. Film boiling condition was established by flooding water onto a high temperature stainless steel ball heated by a high frequency induction heater. After the film boiling was established, the pressure pulse generated by a shock tube was applied to collapse the steam film on the ball surface. As the experimental boundary conditions, materials and size of the balls, magnitude of pressure pulse and initial temperature of the carbon and stainless steel balls were varied. The transients of pressure and surface temperature were measured. It was found that the surface temperature on the balls sharply decreased when the pressure wave passed through the film on balls. Based on the surface temperature behavior, the film boiling collapse pattern was found to be categorized into several types. Especially, the pattern for stainless steel ball was categorized into three types; no collapse, collapse and reestablishment after collapse. It was thus clarified that the film boiling collapse behavior was identified by initial conditions and that the pressure required to collapse film boiling strongly depended on the initial surface temperature. The present results will provide a useful information for the analysis of vapor explosions based on the thermal detonation model. (J.P.N.)

  17. Nitric-glycolic flowsheet testing for maximum hydrogen generation rate

    Energy Technology Data Exchange (ETDEWEB)

    Martino, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Newell, J. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Williams, M. S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-03-01

    The Defense Waste Processing Facility (DWPF) at the Savannah River Site is developing for implementation a flowsheet with a new reductant to replace formic acid. Glycolic acid has been tested over the past several years and found to effectively replace the function of formic acid in the DWPF chemical process. The nitric-glycolic flowsheet reduces mercury, significantly lowers the chemical generation of hydrogen and ammonia, allows purge reduction in the Sludge Receipt and Adjustment Tank (SRAT), stabilizes the pH and chemistry in the SRAT and the Slurry Mix Evaporator (SME), allows for effective adjustment of the SRAT/SME rheology, and is favorable with respect to melter flammability. The objective of this work was to perform DWPF Chemical Process Cell (CPC) testing at conditions that would bound the catalytic hydrogen production for the nitric-glycolic flowsheet.

  18. 无硝酸添加钼精矿中温加压氧化工艺研究%MEDIUM-TEMPERATURE ACID PRESSURE OXIDATION OF MOLYBDENUM CONCENTRATE WITHOUT NITRIC ACID ADDITIVES

    Institute of Scientific and Technical Information of China (English)

    赵磊; 王玉芳

    2013-01-01

    The metallurgical processing procedure of molybdenum concentrate medium-temperature acid pressure oxidation is investigated. Under the conditions of 180℃ , PO2 =0.606 MPa, leaching time 4 h, additives 5% , liquid/solid ratio 6/1 , and agitator rotating speed 600 r/min, the molybdenum conversion rate is above 99% , and about 20% of molybdenum goes into solution.%研究无硝酸添加钼精矿中温酸性加压氧化工艺过程.在180℃下,氧分压0.606 MPa,反应时间4h,添加剂X5%,液固比6:1,转速600 r/min,钼的转化率可达到99%以上,其中约20%进入溶液.

  19. NITRIC OXIDE INTERFERES WITH HYPOXIA SIGNALING DURING COLONIC INFLAMMATION

    Directory of Open Access Journals (Sweden)

    Cintia Rabelo e Paiva CARIA

    2014-12-01

    Full Text Available Context Intestinal inflammation can induce a local reduction in oxygen levels that triggers an adaptive response centered on the expression of hypoxia-inducible factors (HIFs. Nitric oxide, a well-described inflammatory mediator, may interfere with hypoxia signaling. Objectives We aimed to evaluate the role of nitric oxide in hypoxia signaling during colonic inflammation. Methods Colitis was induced by single (acute or repeated (reactivated colitis trinitrobenzenosulfonic acid administration in rats. In addition, one group of rats with reactivated colitis was also treated with Nw-Nitro-L-arginine methyl ester hydrochloride to block nitric oxide synthase. Colitis was assessed by macroscopic score and myeloperoxidase activity in the colon samples. Hypoxia was determined using the oxygen-dependent probe, pimonidazole. The expression of HIF-1α and HIF-induced factors (vascular endothelial growth factor - VEGF and apelin was assessed using Western blotting. Results The single or repeated administration of trinitrobenzenosulfonic acid to rats induced colitis which was characterized by a high macroscopic score and myeloperoxidase activity. Hypoxia was observed with both protocols. During acute colitis, HIF-1α expression was not increased, but VEGF and apelin were increased. HIF-1α expression was inhibited during reactivated colitis, and VEGF and apelin were not increased. Nw-Nitro-L-arginine methyl ester hydrochloride blockade during reactivated colitis restored HIF-1α, VEGF and apelin expression. Conclusions Nitric oxide could interfere with hypoxia signaling during reactivated colitis inflammation modifying the expression of proteins regulated by HIF-1α.

  20. Marangoni heat transfer in subcooled nucleate pool boiling

    Energy Technology Data Exchange (ETDEWEB)

    Petrovic, S.; Robinson, T.; Judd, R.L. [McMaster University, Hamilton, ON (Canada). Dept. of Mechanical Engineering

    2004-11-01

    The liquid motion induced by surface tension variation, termed the Marangoni effect, and its contribution to boiling heat transfer has been an issue of much controversy. Boiling heat transfer theory, although acknowledging its existence, considers its contribution to heat transfer to be insignificant in comparison with buoyancy induced convection. However, recent microgravity experiments have shown that although the boiling mechanism in a reduced gravity environment is different, the corresponding heat transfer rates are similar to those obtained under normal gravity conditions, raising questions about the validity of the assumption. An experimental investigation was performed in which distilled water was gradually heated to boiling conditions on a copper heater surface at four different levels of subcooling. Photographic investigation of the bubbles appearing on the surface was carried out in support of the measurements. The results obtained indicate that Marangoni convection associated with the bubbles formed by the air dissolved in the water which emerged from solution when the water was heated sufficiently, significantly influenced the heat transfer rate in subcooled nucleate pool boiling. A heat transfer model was developed in order to explain the phenomena observed. (author)

  1. Heater size effect on subcooled pool boiling of FC-72

    Energy Technology Data Exchange (ETDEWEB)

    Raj, Rishi; Kim, Jungho [University of Maryland, College Park, MD (United States). Dept. of Mechanical Engineering

    2009-07-01

    Extensive research has been conducted on pool boiling using heaters larger than the capillary length. For large heaters and/or high gravity conditions, boiling is dominated by buoyancy, and the heat transfer is heater size independent. Much less is known about boiling on small heaters and at low gravity levels. The ratio of heater size L{sub h} to capillary length L{sub c} is an important parameter in the determination of heater size dependence on heat transfer. As the ratio L{sub h}/L{sub c} decreases due to a decrease in either heater size or gravity, surface tension forces become dominant. It is proposed that transition from buoyancy to surface tension dominated boiling occurs when the heater size and bubble departure diameter are of the same order. Previous work in variable gravity with flat surfaces has shown that the heat transfer was heater size independent only when the ratio L{sub h}/L{sub c} was considerably larger than 1. An array of 96 platinum resistance heater elements in a 10 x 10 configuration with individual elements 0.7 x 0.7 mm{sup 2} in size was used to vary heater size and measure the heat transfer. The threshold value of L{sub h}/L{sub c} above which pool boiling is heater size independent was found to be about 2.8. (author)

  2. Boiling crisis and non-equilibrium drying transition

    CERN Document Server

    Nikolayev, Vadim

    2016-01-01

    Boiling crisis is the rapid formation of the quasi-continuous vapor film between the heater and the liquid when the heat supply exceeds a critical value. We propose a mechanism for the boiling crisis that is based on the spreading of the dry spot under a vapor bubble. The spreading is initiated by the vapor recoil force, a force coming from the liquid evaporation into the bubble. Since the evaporation intensity increases sharply near the triple contact line, the influence of the vapor recoil can be described as a change of the apparent contact angle. Therefore, for the most usual case of complete wetting of the heating surface by the liquid, the boiling crisis can be understood as a drying transition from complete to partial wetting. The state of nucleate boiling, which is boiling in its usual sense, is characterized by a very large rate of heat transfer from the heating surface to the bulk because the superheated liquid is carried away from the heating surface by the departing vapor bubbles. If the heating p...

  3. Gravity and Heater Size Effects on Pool Boiling Heat Transfer

    Science.gov (United States)

    Kim, Jungho; Raj, Rishi

    2014-01-01

    The current work is based on observations of boiling heat transfer over a continuous range of gravity levels between 0g to 1.8g and varying heater sizes with a fluorinert as the test liquid (FC-72/n-perfluorohexane). Variable gravity pool boiling heat transfer measurements over a wide range of gravity levels were made during parabolic flight campaigns as well as onboard the International Space Station. For large heaters and-or higher gravity conditions, buoyancy dominated boiling and heat transfer results were heater size independent. The power law coefficient for gravity in the heat transfer equation was found to be a function of wall temperature under these conditions. Under low gravity conditions and-or for smaller heaters, surface tension forces dominated and heat transfer results were heater size dependent. A pool boiling regime map differentiating buoyancy and surface tension dominated regimes was developed along with a unified framework that allowed for scaling of pool boiling over a wide range of gravity levels and heater sizes. The scaling laws developed in this study are expected to allow performance quantification of phase change based technologies under variable gravity environments eventually leading to their implementation in space based applications.

  4. Numerical simulation of pool boiling of a Lennard-Jones liquid

    KAUST Repository

    Inaoka, Hajime

    2013-09-01

    We performed a numerical simulation of pool boiling by a molecular dynamics model. In the simulation, a liquid composed of Lennard-Jones particles in a uniform gravitational field is heated by a heat source at the bottom of the system. The model successfully reproduces the change in regimes of boiling from nucleate boiling to film boiling with the increase of the heat source temperature. We present the pool boiling curve by the model, whose general behavior is consistent with those observed in experiments of pool boiling. © 2013 Elsevier B.V. All rights reserved.

  5. Changes of enthalpy slope in subcooled flow boiling

    Science.gov (United States)

    Collado, Francisco J.; Monné, Carlos; Pascau, Antonio

    2006-03-01

    Void fraction data in subcooled flow boiling of water at low pressure measured by General Electric in the 1960s are analyzed following the classical model of Griffith et al. (in Proceedings of ASME-AIChE heat transfer conference, #58-HT-19, 1958). In addition, a new proposal for analyzing one-dimensional steady flow boiling is used. This is based on the physical fact that if the two phases have different velocities, they cannot cover the same distance—the control volume length—in the same time. So a slight modification of the heat balance is suggested, i.e., the explicit inclusion of the vapor liquid velocity ratio or slip ratio as scaling time factor between the phases, which is successfully checked against the data. Finally, the prediction of void fraction using correlations of the net rate of change of vapor enthalpy in the fully developed regime of subcooled flow boiling is explored.

  6. Boiling heat transfer on fins – experimental and numerical procedure

    Directory of Open Access Journals (Sweden)

    Orzechowski T.

    2014-03-01

    Full Text Available The paper presents the research methodology, the test facility and the results of investigations into non-isothermal surfaces in water boiling at atmospheric pressure, together with a discussion of errors. The investigations were conducted for two aluminium samples with technically smooth surfaces and thickness of 4 mm and 10 mm, respectively. For the sample of lower thickness, on the basis of the surface temperature distribution measured with an infrared camera, the local heat flux and the heat transfer coefficient were determined and shown in the form of a boiling curve. For the thicker sample, for which 1-D model cannot be used, numerical calculations were conducted. They resulted in obtaining the values of the local heat flux on the surface the invisible to the infrared, camera i.e. on the side on which the boiling of the medium proceeds.

  7. Changes of enthalpy slope in subcooled flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco J.; Monne, Carlos [Universidad de Zaragoza-CPS, Departamento de Ingenieria Mecanica-Motores Termicos, Zaragoza (Spain); Pascau, Antonio [Universidad de Zaragoza-CPS, Departamento de Ciencia de los Materiales y Fluidos-Mecanica de Fluidos, Zaragoza (Spain)

    2006-03-01

    Void fraction data in subcooled flow boiling of water at low pressure measured by General Electric in the 1960s are analyzed following the classical model of Griffith et al. (in Proceedings of ASME-AIChE heat transfer conference, 58-HT-19, 1958). In addition, a new proposal for analyzing one-dimensional steady flow boiling is used. This is based on the physical fact that if the two phases have different velocities, they cannot cover the same distance - the control volume length - in the same time. So a slight modification of the heat balance is suggested, i.e., the explicit inclusion of the vapor-liquid velocity ratio or slip ratio as scaling time factor between the phases, which is successfully checked against the data. Finally, the prediction of void fraction using correlations of the net rate of change of vapor enthalpy in the fully developed regime of subcooled flow boiling is explored. (orig.)

  8. Visualization of pool boiling from complex surfaces with internal tunnels

    Directory of Open Access Journals (Sweden)

    Pastuszko Robert

    2012-04-01

    Full Text Available The paper presents experimental investigations of boiling heat transfer for a system of connected narrow horizontal and vertical tunnels. These extended surfaces, named narrow tunnel structure (NTS, can be applied to electronic element cooling. The experiments were carried out with ethanol at atmospheric pressure. The tunnel external covers were manufactured out of 0.1 mm thick perforated copper foil (hole diameters 0.5 mm, sintered with the mini-fins, formed on the vertical side of the 10 mm high rectangular fins and horizontal inter-fin surface. Visualization studies were conducted with a transparent structured model of joined narrow tunnels limited with the perforated foil. The visualization investigations aimed to formulate assumptions for the boiling model through distinguishing boiling types and defining all phases of bubble growth.

  9. Micro-column enhanced boiling structure and its ramification

    Institute of Scientific and Technical Information of China (English)

    汤勇; 陆龙生; 袁冬; 苏达士

    2008-01-01

    Enhanced boiling experiments of two different enhanced structures were carried out in a thermosyphon loop evaporator chamber. One was micro-columns array structure (MCAS), which was fabricated on copper plate surface with interaction high speed wire electrode discharge machining (HS-WEDM). The other was the ramification of MCAS, named micro-column-array and sintered-copper compound structure (MSCS), which was fabricated with sintered method on micro-column array structure. Considering the wall superheat and critical heat flux (CHF), comparisons were made between them. The results show that both MCAS and MSCS can enhance the boiling heat transfer. It is also found that the enhanced boiling heat transfer ability of MSCS is changed obviously while the porosity of the sintered copper layer is changed.

  10. On mechanism of explosive boiling in nanosecond regime

    Science.gov (United States)

    Çelen, Serap

    2016-06-01

    Today laser-based machining is used to manufacture vital parts for biomedical, aviation and aerospace industries. The aim of the paper is to report theoretical, numerical and experimental investigations of explosive boiling under nanosecond pulsed ytterbium fiber laser irradiation. Experiments were performed in an effective peak power density range between 1397 and 1450 MW/cm2 on pure titanium specimens. The threshold laser fluence for phase explosion, the pressure and temperature at the target surface and the velocity of the expulsed material were reported. A narrow transition zone was realized between the normal vaporization and phase explosion fields. The proof of heterogeneous boiling was given with detailed micrographs. A novel thermal model was proposed for laser-induced splashing at high fluences. Packaging factor and scattering arc radius terms were proposed to state the level of the melt ejection process. Results of the present investigation explain the explosive boiling during high-power laser interaction with metal.

  11. A high-fidelity approach towards simulation of pool boiling

    Energy Technology Data Exchange (ETDEWEB)

    Yazdani, Miad; Radcliff, Thomas; Soteriou, Marios; Alahyari, Abbas A. [United Technologies Research Center, East Hartford, Connecticut 06108 (United States)

    2016-01-15

    A novel numerical approach is developed to simulate the multiscale problem of pool-boiling phase change. The particular focus is to develop a simulation technique that is capable of predicting the heat transfer and hydrodynamic characteristics of nucleate boiling and the transition to critical heat flux on surfaces of arbitrary shape and roughness distribution addressing a critical need to design enhanced boiling heat transfer surfaces. The macro-scale of the phase change and bubble dynamics is addressed through employing off-the-shelf Computational Fluid Dynamics (CFD) methods for interface tracking and interphase mass and energy transfer. The micro-scale of the microlayer, which forms at early stage of bubble nucleation near the wall, is resolved through asymptotic approximation of the thin-film theory which provides a closed-form solution for the distribution of the micro-layer and its influence on the evaporation process. In addition, the sub-grid surface roughness is represented stochastically through probabilistic density functions and its role in bubble nucleation and growth is then represented based on the thermodynamics of nucleation process. This combination of deterministic CFD, local approximation, and stochastic representation allows the simulation of pool boiling on any surface with known roughness and enhancement characteristics. The numerical model is validated for dynamics and hydrothermal characteristics of a single nucleated bubble on a flat surface against available literature data. In addition, the prediction of pool-boiling heat transfer coefficient is verified against experimental measurements as well as reputable correlations for various roughness distributions and different surface orientations. Finally, the model is employed to demonstrate pool-boiling phenomenon on enhanced structures with reentrance cavities and to explore the effect of enhancement feature design on thermal and hydrodynamic characteristics of these surfaces.

  12. Defluoridation of drinking water by boiling with brushite and calcite.

    Science.gov (United States)

    Larsen, M J; Pearce, E I F

    2002-01-01

    Existing methods for defluoridating drinking water involve expensive high technology or are slow, inefficient and/or unhygienic. A new method is now suggested, encompassing brushite and calcite suspension followed by boiling. Our aim was to examine the efficiency of the method and the chemical reactions involved. Brushite, 0.3-0.5 g, and an equal weight of calcite were suspended in 1 litre water containing 5-20 ppm fluoride. The suspensions were boiled in an electric kettle, left to cool and the calcium salts to sediment. Solution ion concentrations were determined and sediments were examined by X-ray diffraction. In distilled water initially containing 5, 10 and 20 ppm fluoride the concentration was reduced to 0.06, 0.4 and 5.9 ppm, respectively. Using Aarhus tap water which contained 2.6 mmol/l calcium the final concentrations were 1.2, 2.5 and 7.7 ppm, respectively, and runs without calcite gave results similar to those with calcite. Without boiling the fluoride concentration remained unaltered, as did the brushite and calcite salts, despite occasional agitation by hand. All solutions were supersaturated with respect to fluorapatite and hydroxyapatite and close to saturation with respect to brushite. Boiling produced well-crystallised apatite and traces of calcite, while boiling of brushite alone left a poorly crystallised apatite. We conclude that boiling a brushite/calcite suspension rapidly converts the two salts to apatite which incorporates fluoride if present in solution, and that this process may be exploited to defluoridate drinking water.

  13. High heat flux transport by microbubble emission boiling

    Science.gov (United States)

    Suzuki, Koichi

    2007-10-01

    In highly subcooled flow boiling, coalescing bubbles on the heating surface collapse to many microbubbles in the beginning of transition boiling and the heat flux increases higher than the ordinary critical heat flux. This phenomenon is called Microbubble Emission Boiling, MEB. It is generated in subcooled flow boiling and the maximum heat flux reaches about 1 kW/cm2(10 MW/m2) at liquid subcooling of 40 K and liquid velocity of 0.5 m/s for a small heating surface of 10 mm×10 mm which is placed at the bottom surface of horizontal rectangular channel. The high pressure in the channel is observed at collapse of the coalescing bubbles and it is closely related the size of coalescing bubbles. Periodic pressure waves are observed in MEB and the heat flux increases linearly in proportion to the pressure frequency. The frequency is considered the frequency of liquid-solid exchange on the heating surface. For the large sized heating surface of 50 mm length×20 mm width, the maximum heat flux obtained is 500 W/cm2 (5 MW/m2) at liquid subcooling of 40 K and liquid velocity of 0.5 m/s. This is considerably higher heat flux than the conventional cooling limit in power electronics. It is difficult to remove the high heat flux by MEB for a longer heating surface than 50 mm by single channel type. A model of advanced cooling device is introduced for power electronics by subcooled flow boiling with impinging jets. Themaxumum cooling heat flux is 500 W/cm2 (5 MW/m2). Microbubble emission boiling is useful for a high heat flux transport technology in future power electronics used in a fuel-cell power plant and a space facility.

  14. Heat Transfer in Boiling Dilute Emulsion with Strong Buoyancy

    Science.gov (United States)

    Freeburg, Eric Thomas

    Little attention has been given to the boiling of emulsions compared to that of boiling in pure liquids. The advantages of using emulsions as a heat transfer agent were first discovered in the 1970s and several interesting features have since been studied by few researchers. Early research focuses primarily on pool and flow boiling and looks to determine a mechanism by which the boiling process occurs. This thesis looks at the boiling of dilute emulsions in fluids with strong buoyant forces. The boiling of dilute emulsions presents many favorable characteristics that make it an ideal agent for heat transfer. High heat flux electronics, such as those seen in avionics equipment, produce high heat fluxes of 100 W/cm2 or more, but must be maintained at low temperatures. So far, research on single phase convection and flow boiling in small diameter channels have yet to provide an adequate solution. Emulsions allow the engineer to tailor the solution to the specific problem. The fluid can be customized to retain the high thermal conductivity and specific heat capacity of the continuous phase while enhancing the heat transfer coefficient through boiling of the dispersed phase component. Heat transfer experiments were carried out with FC-72 in water emulsions. FC-72 has a saturation temperature of 56 °C, far below that of water. The parameters were varied as follows: 0% ≤ epsilon ≤ 1% and 1.82 x 1012 ≤ RaH ≤ 4.42 x 1012. Surface temperatures along the heated surface reached temperature that were 20 °C in excess of the dispersed phase saturation temperature. An increase of ˜20% was seen in the average Nusselt numbers at the highest Rayleigh numbers. Holography was used to obtain images of individual and multiple FC-72 droplets in the boundary layer next to the heated surface. The droplet diameters ranged from 0.5 mm to 1.3 mm. The Magnus effect was observed when larger individual droplets were injected into the boundary layer, causing the droplets to be pushed

  15. Hysteresis of boiling for different tunnel-pore surfaces

    Directory of Open Access Journals (Sweden)

    Pastuszko Robert

    2015-01-01

    Full Text Available Analysis of boiling hysteresis on structured surfaces covered with perforated foil is proposed. Hysteresis is an adverse phenomenon, preventing high heat flux systems from thermal stabilization, characterized by a boiling curve variation at an increase and decrease of heat flux density. Experimental data were discussed for three kinds of enhanced surfaces: tunnel structures (TS, narrow tunnel structures (NTS and mini-fins covered with the copper wire net (NTS-L. The experiments were carried out with water, R-123 and FC-72 at atmospheric pressure. A detailed analysis of the measurement results identified several cases of type I, II and III for TS, NTS and NTS-L surfaces.

  16. A Study of the Influence of Solid Particles on Boiling Hysteresis

    Institute of Scientific and Technical Information of China (English)

    M.H.Shi; J.Ma

    1992-01-01

    Experiments have been performed to determine the effects on boiling hysteresis of locally fluidized particles contained in a liquid that serves as coolant for electronic equipment.The results show that Iocally fluidized particles can diminish boiling hysteresis.

  17. 76 FR 14437 - Economic Simplified Boiling Water Reactor Standard Design: GE Hitachi Nuclear Energy; Issuance of...

    Science.gov (United States)

    2011-03-16

    ... From the Federal Register Online via the Government Publishing Office ] NUCLEAR REGULATORY COMMISSION Economic Simplified Boiling Water Reactor Standard Design: GE Hitachi Nuclear Energy; Issuance of... GE Hitachi Nuclear Energy (GEH) for the economic simplified boiling water reactor (ESBWR)...

  18. 77 FR 3009 - Knowledge and Abilities Catalog for Nuclear Power Plant Operators: Advanced Boiling Water Reactors

    Science.gov (United States)

    2012-01-20

    ... From the Federal Register Online via the Government Publishing Office NUCLEAR REGULATORY COMMISSION Knowledge and Abilities Catalog for Nuclear Power Plant Operators: Advanced Boiling Water Reactors..., ``Knowledge and Abilities Catalog for Nuclear Power Plant Operators: Advanced Boiling Water Reactors.''...

  19. Determination of iodine at ppt level in a nitric acid medium by inductively coupled plasma sector field mass spectrometry: influence of the chemical forms; Etude de la determination de traces d'iode en solution par spectrometrie de masse a secteur magnetique utilisant un plasma a couplage inductif comme source d'ionisation: influence de la forme chimique

    Energy Technology Data Exchange (ETDEWEB)

    Langlois, B

    2001-07-01

    Inductively Coupled Plasma Sector Field Mass Spectrometry (ICP/SFMS) was used to determine several chemical forms of iodine, at ppt level, in a nitric acid media. Ascorbic acid was added as a reducing agent in order to maintain iodine as iodide. In a preliminary approach, the influence of the chemical form was studied by comparing inorganic iodine (NaI) and organic iodine (CH3I). Different signal responses were observed. With a conventional sample introduction system, sensitivities obtained for iodo-methane could differ by a factor of 5. This was not caused by a problem of atomization or by a change in the ionization efficiency of the iodo-compound into the plasma. The low volatilization temperature of iodo-methane (315.5 K) seemed to be the main explanation of this phenomena. Actually, nebulization resulted in the volatilization of a 2% nitric acid solution containing iodo-methane. As a result, the transport efficiency of iodo-methane between the nebulizer and the torch was approaching 100%. A Direct Injection High Efficiency Nebulizer (DIHEN) allowed us to minimize the behavior difference between the two iodine species, but the sensitivity ratio was inverted and still differed by 20 - 40%. Moreover, the association of a guard electrode and the direct injection system was studied in order to apply these equipments to the determination of iodine. This association allowed us to improve the sensitivity by a factor of 10 and to minimize memory effects, when compared with a conventional system. Further studies indicated that signal responses obtained with different iodine-containing species, except for iodo-methane, were found to be similar. (author)

  20. Boiling heat transfer and droplet spreading of nanofluids.

    Science.gov (United States)

    Murshed, S M Sohel; de Castro, C A Nieto

    2013-11-01

    Nanofluids- a new class of heat transfer fluids have recently been a very attractive area of research due to their fascinating thermophysical properties and numerous potential benefits and applications in many important fields. However, there are many controversies and inconsistencies in reported arguments and experimental results on various thermal characteristics such as effective thermal conductivity, convective heat transfer coefficient and boiling heat transfer rate of nanofluids. As of today, researchers have mostly focused on anomalous thermal conductivity of nanofluids. Although investigations on boiling and droplet spreading are very important for practical application of nanofluids as advanced coolants, considerably fewer efforts have been made on these thermal features of nanofluids. In this paper, recent research and development in boiling heat transfer and droplet spreading of nanofluids are reviewed together with summarizing most related patents on nanofluids published in literature. Review reveals that despite some inconsistent results nanofluids exhibit significantly higher boiling heat transfer performance compared to their base fluids and show great promises to be used as advanced heat transfer fluids in numerous applications. However, there is a clear lack of in-depth understanding of heat transport mechanisms during phase change of nanofluids. It is also found that the nanofluids related patents are limited and among them most of the patents are based on thermal conductivity enhancement and synthesising processes of specific type of nanofluids.

  1. Measuring radon reduction in xenon boil-off gas

    Energy Technology Data Exchange (ETDEWEB)

    Bruenner, Stefan; Cichon, Dominick; Lindemann, Sebastian; Marrodan Undagoitia, Teresa; Simgen, Hardy [MPIK, Heidelberg (Germany)

    2016-07-01

    {sup 222}Rn, which originates from the decay of primordial {sup 238}U, is one of the major background sources for ultra-low background noble gas detectors. One of them is XENON1T, which is a dark matter direct detection experiment looking for hypothetical weakly interacting massive particles (WIMPs). It uses liquid xenon (LXe) as a detection medium and aims to be sensitive to spin-independent WIMP-nucleon cross-sections of σ∝2.10{sup -47} cm{sup 2} at a WIMP mass of ∝50 GeV/c{sup 2}. To achieve this goal, radon activity inside the detector must be limited to a few mBq/kg. One possible way for reducing the concentration of {sup 222}Rn inside such an LXe detector is using the so-called ''boil-off method''. It takes advantage of the fact, that the radon concentration in boil-off xenon is smaller compared to the concentration in the liquid xenon from which the boil-off xenon evaporated. This can be understood by the different vapor pressures of radon and xenon. In this talk, tests conducted at the MPIK are outlined which probe the feasibility and effectiveness of the boil-off method. The results prove, that a reduction of the radon concentration can indeed be achieved. In addition, an outlook for possible future applications of this technique is given.

  2. Boiling process in oil coolers on porous elements

    Directory of Open Access Journals (Sweden)

    Genbach Alexander A.

    2016-01-01

    Full Text Available Holography and high-speed filming were used to reveal movements and deformations of the capillary and porous material, allowing to calculate thermo-hydraulic characteristics of boiling liquid in the porous structures. These porous structures work at the joint action of capillary and mass forces, which are generalised in the form of dependences used in the calculation for oil coolers in thermal power plants (TPP. Furthermore, the mechanism of the boiling process in porous structures in the field of mass forces is explained. The development process of water steam formation in the mesh porous structures working at joint action of gravitational and capillary forces is investigated. Certain regularities pertained to the internal characteristics of boiling in cells of porous structure are revealed, by means of a holographic interferometry and high-speed filming. Formulas for calculation of specific thermal streams through thermo-hydraulic characteristics of water steam formation in mesh structures are obtained, in relation to heat engineering of thermal power plants. This is the first calculation of heat flow through the thermal-hydraulic characteristics of the boiling process in a reticulated porous structure obtained by a photo film and holographic observations.

  3. How long does it take to boil an egg? Revisited

    Energy Technology Data Exchange (ETDEWEB)

    Buay, D [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Foong, S K [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Kiang, D [Department of Physics, Chinese University of Hong Kong, Shatin, New Territories, Hong Kong (China); Kuppan, L [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Centre for Research in Pedagogy and Practice, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Liew, V H [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore)

    2006-01-01

    How long does it take to boil an egg? Theoretical prediction, based on a simple adaptation of the solution to the exact thermal diffusion equation for a sphere, is consistent with experiments. The experimental data are also used to estimate an average value for the thermal diffusivity of an egg.

  4. Experimental demonstration of contaminant removal from fractured rock by boiling.

    Science.gov (United States)

    Chen, Fei; Liu, Xiaoling; Falta, Ronald W; Murdoch, Lawrence C

    2010-08-15

    This study was conducted to experimentally demonstrate removal of a chlorinated volatile organic compound from fractured rock by boiling. A Berea sandstone core was contaminated by injecting water containing dissolved 1,2-DCA (253 mg/L) and sodium bromide (144 mg/L). During heating, the core was sealed except for one end, which was open to the atmosphere to simulate an open fracture. A temperature gradient toward the outlet was observed when boiling occurred in the core. This indicates that steam was generated and a pressure gradient developed toward the outlet, pushing steam vapor and liquid water toward the outlet. As boiling occurred, the concentration of 1,2-DCA in the condensed effluent peaked up to 6.1 times higher than the injected concentration. When 38% of the pore volume of condensate was produced, essentially 100% of the 1,2-DCA was recovered. Nonvolatile bromide concentration in the condensate was used as an indicator of the produced steam quality (vapor mass fraction) because it can only be removed as a solute, and not as a vapor. A higher produced steam quality corresponds to more concentrated 1,2-DCA removal from the core, demonstrating that the chlorinated volatile compound is primarily removed by partitioning into vapor phase flow. This study has experimentally demonstrated that boiling is an effective mechanism for CVOC removal from the rock matrix.

  5. Investigation Status of Heat Exchange while Boiling Hydrocarbon Fuel

    Directory of Open Access Journals (Sweden)

    D. S. Obukhov

    2006-01-01

    Full Text Available The paper contains analysis of heat exchange investigations while boiling hydrocarbon fuel. The obtained data are within the limits of the S.S. Kutateladze dependence proposed in 1939. Heat exchange at non-stationary heat release has not been investigated. The data for hydrocarbon fuel with respect to critical density of heat flow are not available even for stationary conditions.

  6. A Review of Boiling Heat Transfer Processes at High Heat Flux

    Science.gov (United States)

    1991-04-01

    liquid metals) which can lead to explosive boiling (known as bumping) that can lead to structural damage to hardware. 3 Transition boiling occurs between...to initiate boiling, in some cases having an explosive transition that can cause structural damage to hardware. A thorough understanding of boiling...graphical correlations for the pressure drops encountered in their experiments. About the same time, Staub and Walmet (Ref. 173) identified the two regions

  7. Nucleate Pool Boiling Experiments (NPBX) on the International Space Station

    Science.gov (United States)

    Dhir, Vijay Kumar; Warrier, Gopinath R.; Aktinol, Eduardo; Chao, David; Eggers, Jeffery; Sheredy, William; Booth, Wendell

    2012-11-01

    During the period of March-May 2011, a series of boiling experiments was carried out in the Boiling Experimental Facility (BXF) located in the Microgravity Science Glovebox (MSG) of the International Space Station (ISS). The BXF Facility was carried to ISS on Space Shuttle Mission STS-133 on February 24, 2011. Nucleate Pool Boiling Experiment (NPBX) was one of the two experiments housed in the BXF. Results of experiments on single bubble dynamics (e.g., inception and growth), multiple bubble dynamics (lateral merger and departure, if any), nucleate pool boiling heat transfer, and critical heat flux are described. In the experiments Perfluoro-n-hexane was used as the test liquid. The system pressure was varied from 51 to 243 kPa, pool temperature was varied from 30° to 59°C, and test surface temperature was varied from 40° to 80°C. The test surface was a polished aluminum disc (1 mm thick, 89.5 mm in diameter) heated from below with strain gage heaters. Five cylindrical cavities were formed on the surface with four cavities located at the corners of a square and one in the middle. During experiments the magnitude of mean gravity level normal to the heater surface varied from 1.2 × 10 - 7g e to 6 × 10 - 7g e . The results of the experiments show that a single bubble continues to grow to occupy the size of the chamber without departing from the heater surface. During lateral merger of bubbles, at high superheats a large bubble may lift off from the surface but continues to hover near the surface. Neighboring bubbles are continuously pulled into the large bubble. At low superheats bubbles at neighboring sites simply merge to yield a larger bubble. The larger bubble mostly locates in the middle of the heated surface and serves as a vapor sink. The latter mode continues to persist when boiling is occurring all over the heater surface. Heat fluxes for steady state nucleate boiling and critical heat fluxes are found to be much lower than those obtained under earth

  8. A Study of Nucleate Boiling with Forced Convection in Microgravity

    Science.gov (United States)

    Merte, Herman, Jr.

    1999-01-01

    The ultimate objective of basic studies of flow boiling in microgravity is to improve the understanding of the processes involved, as manifested by the ability to predict its behavior. This is not yet the case for boiling heat transfer even in earth gravity, despite the considerable research activity over the past 30 years. The elements that constitute the nucleate boiling process - nucleation, growth, motion, and collapse of the vapor bubbles (if the bulk liquid is subcooled) - are common to both pool and flow boiling. It is well known that the imposition of bulk liquid motion affects the vapor bubble behavior relative to pool boiling, but does not appear to significantly influence the heat transfer. Indeed, it has been recommended in the past that empirical correlations or experimental data of pool boiling be used for design purposes with forced convection nucleate boiling. It is anticipated that such will most certainly not be possible for boiling in microgravity, based on observations made with pool boiling in microgravity. In earth gravity buoyancy will act to remove the vapor bubbles from the vicinity of the heater surface regardless of how much the imposed bulk velocity is reduced, depending, of course, on the geometry of the system. Vapor bubbles have been observed to dramatically increase in size in pool boiling in microgravity, and the heat flux at which dryout took place was reduced considerably below what is generally termed the critical heat flux (CHF) in earth gravity, depending on the bulk liquid subcooling. However, at heat flux levels below dryout, the nucleate pool boiling process was enhanced considerably over that in earth gravity, in spite of the large vapor bubbles formed in microgravity and perhaps as a consequence. These large vapor bubbles tended to remain in the vicinity of the heater surface, and the enhanced heat transfer appeared to be associated with the presence of what variously has been referred to as a liquid microlayer between the

  9. Bubble and boundary layer behaviour in subcooled flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Maurus, Reinhold; Sattelmayer, Thomas [Lehrstuhl fuer Thermodynamik, Technische Universitaet Muenchen, 85747 Garching (Germany)

    2006-03-15

    Subcooled flow boiling is a commonly applied technique for achieving efficient heat transfer. In the study, an experimental investigation in the nucleate boiling regime was performed for water circulating in a closed loop at atmospheric pressure. The horizontal orientated test-section consists of a rectangular channel with a one side heated copper strip and good optical access. Various optical observation techniques were applied to study the bubble behaviour and the characteristics of the fluid phase. The bubble behaviour was recorded by the high-speed cinematography and by a digital high resolution camera. Automated image processing and analysis algorithms developed by the authors were applied for a wide range of mass flow rates and heat fluxes in order to extract characteristic length and time scales of the bubbly layer during the boiling process. Using this methodology, the bubbles were automatically analysed and the bubble size, bubble lifetime, waiting time between two cycles were evaluated. Due to the huge number of observed bubbles a statistical analysis was performed and distribution functions were derived. Using a two-dimensional cross-correlation algorithm, the averaged axial phase boundary velocity profile could be extracted. In addition, the fluid phase velocity profile was characterised by means of the particle image velocimetry (PIV) for the single phase flow as well as under subcooled flow boiling conditions. The results indicate that the bubbles increase the flow resistance. The impact on the flow exceeds by far the bubbly region and it depends on the magnitude of the boiling activity. Finally, the ratio of the averaged phase boundary velocity and of the averaged fluid velocity was evaluated for the bubbly region. (authors)

  10. Citric Acid Alternative to Nitric Acid Passivation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Corrosion is an extensive problem that impacts National Aeronautics and Space Administration (NASA) and Department of Defense (DoD).  The deleterious...

  11. Zero Boil Off Cryogen Storage for Future Launchers

    Science.gov (United States)

    Valentian, D.; Plachta, D.; Kittel, P.; Hastings, L. J.; Salerno, Louis J.; Arnold, James O. (Technical Monitor)

    2001-01-01

    Zero boil off (ZBO) cryogen storage using both cryocoolers and passive insulation technologies will enable long-term exploration missions by allowing designers to optimize tankage without the need for excess cryogen storage to account for boil off. Studies of ZBO (zero boil off) have been on-going in the USA for several years. More recently, a review of the needs of advanced space propulsion took place in Europe. This showed the interest of the European community in cryogenic propulsion for planetary missions as well as the use of liquid hydrogen for large power electric propulsion (manned Mars missions). Although natural boiling could be acceptable for single leg missions, passive insulation techniques yield roughly a I% per month cryogen loss and this would not be cost effective for robotic planetary missions involving storage times greater than one year. To make economic sense, long-term exploration missions require lower tank capacity and longer storage times. Recent advances in cryocooler technology, resulting in vast improvements in both cooler efficiency and reliability, make ZBO is a clear choice for planetary exploration missions. Other, more near term applications of ZBO include boil-off reduction or elimination applied to first and upper stages of future earth-to-orbit (ETO) launchers. This would extend launch windows and reduce infrastructure costs. Successors to vehicles like Ariane 5 could greatly benefit by implementing ZBO. Zero Boil Off will only be successful in ETO launcher applications if it makes economic sense to implement. The energy cost is only a fraction of the total cost of buying liquid cryogen, the rest being transportation and other overhead. Because of this, higher boiling point cryogens will benefit more from on-board liquefaction, thus reducing the infrastructure costs. Since hydrogen requires a liquefier with at least a 17% efficiency just to break even from a cost standpoint, one approach for implementing ZBO in upper stages would

  12. Development of a mechanistic model for forced convection subcooled boiling

    Science.gov (United States)

    Shaver, Dillon R.

    The focus of this work is on the formulation, implementation, and testing of a mechanistic model of subcooled boiling. Subcooled boiling is the process of vapor generation on a heated wall when the bulk liquid temperature is still below saturation. This is part of a larger effort by the US DoE's CASL project to apply advanced computational tools to the simulation of light water reactors. To support this effort, the formulation of the dispersed field model is described and a complete model of interfacial forces is formulated. The model has been implemented in the NPHASE-CMFD computer code with a K-epsilon model of turbulence. The interfacial force models are built on extensive work by other authors, and include novel formulations of the turbulent dispersion and lift forces. The complete model of interfacial forces is compared to experiments for adiabatic bubbly flows, including both steady-state and unsteady conditions. The same model is then applied to a transient gas/liquid flow in a complex geometry of fuel channels in a sodium fast reactor. Building on the foundation of the interfacial force model, a mechanistic model of forced-convection subcooled boiling is proposed. This model uses the heat flux partitioning concept and accounts for condensation of bubbles attached to the wall. This allows the model to capture the enhanced heat transfer associated with boiling before the point of net generation of vapor, a phenomenon consistent with existing experimental observations. The model is compared to four different experiments encompassing flows of light water, heavy water, and R12 at different pressures, in cylindrical channels, an internally heated annulus, and a rectangular channel. The experimental data includes axial and radial profiles of both liquid temperature and vapor volume fraction, and the agreement can be considered quite good. The complete model is then applied to simulations of subcooled boiling in nuclear reactor subchannels consistent with the

  13. Radon depletion in xenon boil-off gas

    CERN Document Server

    Bruenner, S; Lindemann, S; Undagoitia, T Marrodán; Simgen, H

    2016-01-01

    An important background in detectors using liquid xenon for rare event searches arises from the decays of radon and its daughters. We report for the first time a reduction of $^{222}$Rn in the gas phase above a liquid xenon reservoir. We show a reduction factor of $\\gtrsim 4$ for the $^{222}$Rn concentration in boil-off xenon gas compared to the radon enriched liquid phase. A semiconductor-based $\\alpha$-detector and miniaturized proportional counters are used to detect the radon. As the radon depletion in the boil-off gas is understood as a single-stage distillation process, this result establishes the suitability of cryogenic distillation to separate radon from xenon down to the $10^{-15}\\,$mol/mol level.

  14. Radon depletion in xenon boil-off gas

    Science.gov (United States)

    Bruenner, S.; Cichon, D.; Lindemann, S.; Undagoitia, T. Marrodán; Simgen, H.

    2017-03-01

    An important background in detectors using liquid xenon for rare event searches arises from the decays of radon and its daughters. We report for the first time a reduction of ^{222}Rn in the gas phase above a liquid xenon reservoir. We show a reduction factor of ≳ 4 for the ^{222}Rn concentration in boil-off xenon gas compared to the radon enriched liquid phase. A semiconductor-based α -detector and miniaturized proportional counters are used to detect the radon. As the radon depletion in the boil-off gas is understood as a single-stage distillation process, this result establishes the suitability of cryogenic distillation to separate radon from xenon down to the 10^{-15} mol/mol level.

  15. Catastrophe characteristics of the condensation and pool boiling phenomena

    Science.gov (United States)

    Ma, Xuehu; Xu, Dunqi; Lin, Jifang

    1995-02-01

    Recently, Utaka proposed two types of the transition modes of dropwise condensation, i.e. the continuous and the jumping modes, and presented a criterion for determining the condensation transition mode. Stylianous and Rose proposed two hypotheses, the coalescence-limited transition and the nucleation site saturation transition. Neither Utaka's criterion nor Rose's hypotheses could clearly interpret the physical mechanisms of the transition both from filmwise to dropwise and from dropwise to pseudofilm condensation, and explicitly presented the main factors affecting the transitions. Kalinin hs given a general review of the transition boiling heat transfer. The catastrophe theory will be applied here to eluicidate the complex phenomena of the transitions of the condensation and boiling pattern states.

  16. Molecular Dynamics Simulation of Bubble Nucleation in Explosive Boiling

    Institute of Scientific and Technical Information of China (English)

    ZOU Yu; HUAI Xiu-Lan; LIANG Shi-Qiang

    2009-01-01

    Molecular dynamics (MD) simulation is carried out for the bubble nucleation of liquid nitrogen in explosive boiling. The heat is transferred into the simulation system by rescaling the velocity of the molecules. The results indicate that the initial equilibrium temperature of liquid and molecular cluster size affect the energy conversion in the process of bubble nucleation. The potential energy of the system violently varies at the beginning of the bubble nucleation, and then varies around a fixed value. At the end of bubble nucleation, the potential energy of the system slowly increases. In the bubble nucleation of explosive boiling, the lower the initial equilibrium temperature, the larger the size of the molecular cluster, and the more the heat transferred into the system of the simulation cell, causing the increase potential energy in a larger range.

  17. Numerical analysis on pool boiling using user defined function

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, Sung Uk; Jeon, Byong Guk; Kim, Seok; Euh, Dong-Jin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    PAFS (passive auxiliary feedwater system) adopted in the APR+ (Advanced Power Reactor Plus) of Korea is one such application. When PAFS is activated with an actuation signal, steam from the steam generator passes through heat exchanger tubes submerged in a water tank of the PAFS. Outside these heat exchanger tubes, nucleate boiling phenomena appears. In the present work, a numerical study is reported on three-dimensional transient state pool boiling of water having an immersed heat source. The velocity vector fields during the decrease in the water level are numerically investigated in a pool, and the accuracy of the results is checked by comparing the experimental results conducted using the PIV techniques by Kim et al. These numerical results can be used as basic research data for an analysis and prediction of the natural circulation phenomena in the cooling tank of the passive safety system in a nuclear power plant.

  18. Boiling heat transfer in horizontal and inclined rectangular channels

    Energy Technology Data Exchange (ETDEWEB)

    Morcos, S.M.; Mobarak, A.; Hilal, M.; Mohareb, M.R. (Cairo Univ. (Egypt))

    1987-05-01

    The present experimental investigation is concerned with boiling heat transfer of water inside both horizontal and inclined rectangular channels under a relatively low heat flux. These configurations simulate the absorber channel of line-focus solar concentrations under boiling conditions. The experimental facility includes electrically heated aluminum rectangular channels with aspect ratios of 2.67 and 0.37. The experimental results of the two-phase Nusselt number for the two aspect ratios and for the inclination angles 0, 15, 30, and 45 deg were correlated in terms of a ratio of the two-phase to the liquid-phase Reynolds number for the forced-convection vaporization region. The proposed correlations agree well with previous investigations. In the present work, classifications of the various flow patterns were made by direct observation through a glass window at the end of the test section.

  19. Microlayer formation characteristics in pool isolated bubble boiling of water

    Science.gov (United States)

    Yabuki, Tomohide; Nakabeppu, Osamu

    2016-10-01

    Investigation of microlayer formation characteristics is important for developing a reliable nucleate boiling heat transfer model based on accurate physical mechanisms. Although formation mechanisms of the thin liquid film in two-phase flow of confined spaces, such as micro-tubes and closely positioned parallel plates, have been thoroughly studied, microlayer formation mechanisms of pool boiling have been sparsely studied. In a previous study (Yabuki and Nakabeppu in Int J Heat Mass Transf 76:286-297, 2014; Int J Heat Mass Transf 100:851-860, 2016), the spatial distribution of initial microlayer thickness under pool boiling bubbles was calculated by transient heat conduction analysis using the local wall temperature measured with a MEMS sensor. In this study, the hydrodynamic characteristics of microlayer formation in pool boiling were investigated using the relationship between derived initial microlayer thickness and microlayer formation velocity determined by transient local heat flux data. The trend of microlayer thickness was found to change depending on the thickness of the velocity boundary layer outside the bubble foot. When the boundary layer thickness was thin, the initial microlayer thickness was determined by the boundary layer thickness, and the initial microlayer thickness proportionally increased with increasing boundary layer thickness. On the other hand, when the boundary layer was thick, the initial microlayer thickness decreased with increasing boundary layer thickness. In this thick boundary layer region, the momentum balance in the dynamic meniscus region became important, in addition to the boundary layer thickness, and the microlayer thickness, made dimensionless using boundary layer thickness, correlated with the Bond number.

  20. Prediction of film boiling heat transfer coefficients for binary mixtures

    Science.gov (United States)

    Liu, Ming-Huei; Yang, Yu-Min; Maa, Jer-Ru

    Film boiling of binary liquid mixtures may be significantly different from that of single-component liquids due to the mass diffusion effect. A theoretical analysis is performed to outline the effects of mass diffusion phenomena on film boiling heat transfer process from a horizontal cylinder heating surface to the binary liquid mixtures of ethylene oxide/water and ethanol/benzene over whole range of compositions. These two binary systems are chosen for illustrating the strong and weak mass diffusion effects, respectively, on film boiling. Furthermore, a simple correlation for predicting heat transfer coefficient is proposed to demonstrate the idea that the dimensionless F factor can satisfactorily account for the mass diffusion effect on film boiling heat transfer of binary mixtures. Zusammenfassung Infolge des Stoffdiffusionseffektes kann sich das Filmsiedeverhalten binärer Flüssigkeitsgemische ganz wesentlich von dem der Einzelkomponentenfluide unterscheiden. In einer theoretischen Studie sollen die Einflüsse der Stoffdiffusionsphänomene auf den Wärmeübergang beim Filmsieden untersucht werden, und zwar bezüglich einer horizontalen zylindrischen Heizfläche, die Wärme an die Binärgemische Ethylenoxid/Wasser und Ethanol/Benzol bei beliebigen Konzentrationsverhältnissen abgibt. Die beiden Binärsysteme wurden ausgewählt, um einmal starken und dann schwachen Einfluß des Stoffdiffusionseffektes auf das Filmsieden zu zeigen. Schließlich wird eine einfache Korrelationsbeziehung zur Berechnung von Wärmeübergangskoeffizienten vorgeschlagen, die darlegen soll, daß der dimensionslose F-Faktor geeignet ist, den Einfluß des Stoffdiffusionseffektes auf das Filmsieden binärer Gemische befriedigend zu berücksichtigen.

  1. A review on saturated boiling of liquids on tube bundles

    Science.gov (United States)

    Swain, Abhilas; Das, Mihir Kumar

    2014-05-01

    A review of recent investigation on boiling of saturated liquids over plain and enhanced tube bundles has been carried out taking the earlier review works as reference point. The experimental observations of various geometry and performance parameters studied by researchers are analyzed keeping current demand of industries in design and development of compact, efficient heat exchanging devices. The study shows that tube spacing plays an important role in determination of compactness of the heat exchanger.

  2. Pool boiling on rectangular fins with tunnel-pore structure

    Directory of Open Access Journals (Sweden)

    Pastuszko A.

    2013-04-01

    Full Text Available Complex experimental investigations were conducted in the area of pool boiling heat transfer on extended surfaces with internal tunnels limited by perforated foil. The experiments were carried out for water and R-123 at atmospheric pressure. The tunnel surfaces were fabricated from 0.05 – 0.1 mm thick perforated copper foil (pore diameters: 0.3, 0.4, 0.5 mm sintered with mini-fins formed by 5 and 10 mm high rectangular fins and horizontal inter-fin surface. The effect of the main fin height, pore diameters and tunnel pitch on nucleate pool boiling was examined. Substantial enhancement of heat transfer coefficient was observed for the investigated surfaces. The highest increase in the heat transfer coefficient was obtained for the 10 mm high fins – about 50kW/m2K for water and 15 kW/m2K for R-123. The investigated surfaces showed boiling heat transfer coefficients similar to those of existing tunnel-pore structures.

  3. Boiling of an emulsion in a yield stress fluid

    Science.gov (United States)

    Guéna, Geoffroy; Wang, Ji; D'Espinose, Jean-Baptiste; Lequeux, François; Talini, Laurence

    2010-11-01

    We report the boiling behavior of pentane emulsified in a yield stress fluid, a colloidal clay (Laponite) suspension. We have observed that a superheated state is easily reached: the emulsion, heated more than 50°C above the alkane boiling point, does not boil. Superheating is made possible by the suppression of heterogeneous nucleation in pentane, resulting from the emulsification process, a phenomenon evidenced decades ago in studies of the superheating of two phase fluids. We have furthermore studied the growth of isolated bubbles nucleated in the emulsion. The rate of increase of the bubble radius with time depends on both the temperature and emulsion volume fraction but, rather unexpectedly, does not depend on the fluid rheology. We show that the bubbles grow by diffusion of the alkane through the aqueous phase between liquid droplets and bubbles, analogously to an Ostwald ripening process. The peculiarity of the process reported here is that a layer depleted in oil droplets forms around the bubble, layer to which the alkane concentration gradient is confined. We successfully describe our experimental results with a simple transfer model.

  4. Early-Evaporation of Microlayer for Boiling Heat Transfer Enhancement.

    Science.gov (United States)

    Zou, An; Singh, Dhirendra P; Maroo, Shalabh C

    2016-10-06

    For over five decades, enhancement in pool boiling heat transfer has been achieved by altering the surface wetting, wickability, roughness, nucleation site density and providing separate liquid/vapor pathways. In this work, a new enhancement mechanism based on the early-evaporation of the microlayer is discovered and validated. The microlayer is a thin liquid film present at the base of a vapor bubble. Presence of micro-ridges on the silicon-dioxide surface partitions the microlayer and disconnects it from bulk liquid causing it to evaporate sooner, thus leading to increase in bubble growth rate, heat transfer, departure frequency and critical heat flux (CHF). Compared to a plain surface, ~120% enhancement in CHF is obtained with only ~18% increase in surface area. A CHF enhancement map is developed based on ridge height and spacing, resulting in three regions of full, partial and no enhancement. The new mechanism is validated by comparing the growth rate of a laser created vapor bubble on ridge-structured surface and plain surface, and the corresponding prediction of CHF enhancement is found to be in good agreement with experimental boiling data. This discovery opens up a new field of CHF enhancement and can be coupled with existing techniques to further push the limits of boiling heat transfer.

  5. Experimental Investigation of Flow Boiling in Parallel Mini-channels

    Science.gov (United States)

    Wu, Wan.; Zhang, M. T.; Zhang, X. B.; Xia, J. J.; Wen, S.-Z.; Wang, Z.-R.; He, Z.-H.; Huang, Z.-C.

    2015-07-01

    Flow boiling in micro-channels and mini-channels has received significant attention due to its capability for dissipating highflux heat, especially in the thermal management of high precision electronics. A heat sink with narrow rectangular mini-channels is designed to investigate flow boiling in the mini-channels, including the effect of gravity. It contains 14 parallel channels with a cross section, of 1×4mm 2, of which the hydraulic diameter is 1.6mm. The cooling capability, the temperature uniformity, and the temperature stability of the flow boiling in minichannels are investigated with R22, with total mass flow flux ranges from 35 to 70kg/m 2s. The results show that the cooling capability of the heat- sink is up to 340W(˜ 3.0W/cm 2), and the temperature difference is below 4 ∘C(even down to 2 ∘C) on the heat sink. The temperature uniformity isn't quite sensitive to heat flux. The instability has not been observed in the present researches.

  6. CHF Phenomena by Photographic Study of Boiling Behavior due to Transient Heat Inputs

    Directory of Open Access Journals (Sweden)

    Jongdoc Park

    2012-01-01

    Full Text Available The transient boiling heat transfer characteristics in a pool of water and highly wetting liquids such as ethanol and FC-72 due to an exponentially increasing heat input of various rates were investigated using the 1.0 mm diameter experimental heater shaped in a horizontal cylinder for wide ranges of pressure and subcooling. The trend of critical heat flux (CHF values in relation to the periods was divided into three groups. The CHF belonging to the 1st group with a longer period occurs with a fully developed nucleate boiling (FDNB heat transfer process. For the 2nd group with shorter periods, the direct transition to film boiling from non boiling occurs as an explosive boiling. The direct boiling transition at the CHF from non-boiling regime to film boiling occurred without a heat flux increase. It was confirmed that the initial boiling behavior is significantly affected by the property and the wettability of the liquid. The photographic observations on the vapor bubble behavior during transitions to film boiling were performed using a high-speed video camera system.

  7. Rheological Properties and Structural Changes in Different Sections of Boiled Abalone Meat

    Institute of Scientific and Technical Information of China (English)

    GAO Xin; TANG Zhixu; ZHANG Zhaohui; Ogawa Hiroo

    2003-01-01

    Changes in tissue structures, rheological properties of cross- and vertical section boiled abalone meat were studied in relation to boiling time. The adductor muscle of abalone Haliotis discus which was removed from the shell, was boiled for 1, 2, and 3 h, respectively. Then it was cut up and separated into cross- and vertical section meat. When observed by a light microscope and a scanning electron microscope, structural changes in the myofibrils were greatest in the cross section meat compared with the vertical section meat. When boiling time was increased from 1 h to 3 h, the instantaneous modulus E0 and rupture strength of both section meat decreased gradually with increased boiling time, and no significant differences were observed between these two section meat for the same boiling time. When boiled for 1 h, the relaxation time of cross section meat was much longer than that of vertical section meat. There were no significant changes in the relaxation time of vertical section for different boiling time, but the relaxation time of cross section meat was reduced gradually with increasing boiling time. These results confirmed that the difference in rheological properties between the cross- and vertical section meat was mainly due to the denaturation level of myofibrils when heated for 1 h, as well as due to the changes in the amount of denatured proteins, and the manner in which the inner denatured protein components weve exchanged after boiling time was increased from 1 h to 3 h.

  8. Study on model of onset of nucleate boiling in natural circulation with subcooled boiling using unascertained mathematics

    Energy Technology Data Exchange (ETDEWEB)

    Zhou Tao [Department of Thermal Engineering, Tsinghua University, Beijing 100084 (China)]. E-mail: zhoutao@mail.tsinghua.edu.cn; Wang Zenghui [Department of Engineering Mechanics, Tsinghua University, Beijing 100084 (China); Yang Ruichang [Department of Thermal Engineering, Tsinghua University, Beijing 100084 (China)

    2005-10-01

    Experiment data got from onset of nucleate boiling (ONB) in natural circulation is analyzed using unascertained mathematics. Unitary mathematics model of the relation between the temperature and onset of nucleate boiling is built up to analysis ONB. Multiple unascertained mathematics models are also built up with the onset of natural circulation boiling equation based on the experiment. Unascertained mathematics makes that affirmative results are a range of numbers that reflect the fluctuation of experiment data more truly. The fluctuating value with the distribution function F(x) is the feature of unascertained mathematics model and can express fluctuating experimental data. Real status can be actually described through using unascertained mathematics. Thus, for calculation of ONB point, the description of unascertained mathematics model is more precise than common mathematics model. Based on the unascertained mathematics, a new ONB model is developed, which is important for advanced reactor safety analysis. It is conceivable that the unascertained mathematics could be applied to many other two-phase measurements as well.

  9. Inducible nitric oxide synthase in renal transplantation

    NARCIS (Netherlands)

    Joles, JA; Vos, IH; Grone, HJ; Rabelink, TJ

    2002-01-01

    The importance of the endothelial isoform of nitric oxide synthase (eNOS) has been well established. Endothelium-derived nitric oxide has been shown to be essential for vascular homeostasis and modulation of eNOS has thus become a target in prevention of cardiovascular disease. The role of the induc

  10. Nitric oxide fumigation for postharvest pest control

    Science.gov (United States)

    Nitric oxide fumigation is effective against all arthropod pests at various life stages tested. Nine insect pests at various life stages and bulb mites were subjected to nitric oxide fumigation treatments under ultralow oxygen conditions of =50 ppm O2 in 1.9L glass jars as fumigation chambers. The ...

  11. Boil-off gas vapors are recovered by reliquefaction in LNG

    Energy Technology Data Exchange (ETDEWEB)

    Levay, M.; Petit, P.; Paradowski, H.

    1986-02-24

    Although great care is taken to prevent heat leaks into cryogenic equipment in LNG terminals, boil-off vapors evolve from LNG stored at thermodynamic equilibrium. The quantities of boil-off vapors may be quite considerable. They account for about 1% of the total gas quantity received and sent out at the monitor-de-bretagne LNG terminal of Gaz de France. A novel process has significantly cut boil-off vapor handling costs. It is free of technical problems which would arise from local utilization of the gas and makes boil-off recovery possible under optimum conditions. In addition, the process shows an excellent degree of reliability. Boil-off vapors have a lower heating value than the stored LNG. However, since they mainly consist of methane, their economic usefulness makes vapor recovery necessary. This boil-off gas, with widely fluctuating quantities and qualities, cannot be readily used locally. The vapors must be sent out into the grid.

  12. Nitric oxide and teratogenesis: an update.

    Science.gov (United States)

    Tiboni, Gian Mario; Ponzano, Adalisa

    2014-01-01

    Nitric oxide (NO), generated by NO synthase (NOS) enzymes, is an important bioactive molecule involved in the regulation of several biological phenomena that are crucial for organogenesis, including gene expression, cell growth, matrix remolding, proliferation, differentiation and apoptosis. The expression of NOS isoforms in embryonic tissues is temporally and spatially regulated, and disruption of endogenous NO can lead to developmental defects. Maternal treatment with pan NOS inhibitors during early organogenesis caused severe malformations of the axial skeleton. In utero exposure during the fetal period induced limb reduction defects of vascular origin. Knock-out mice have been used to define the role of the various NOS isoforms on the origin of the abnormal development. Cardiovascular malformations, limb reduction defects, reduced growth and reduced survival have been observed in knock-out mice with targeted disruption of endothelial NOS (eNOS). Limited morphological changes were observed in mice lacking inducible NOS (iNOS) or neuronal NOS n(NOS). Results obtained with in vitro studies suggest that optimal levels of NO are required for neural tube closure. Disregulation of NO production was also recently proposed as a contributing mechanism in the origin of malformations associated with exposure to known environmental teratogens, such as valproic acid, thalidomide, copper deficiency, and diabetes.

  13. Acoustic monitoring of sodium boiling in a liquid metal fast breeder reactor from autoregressive models

    Energy Technology Data Exchange (ETDEWEB)

    Geraldo, Issa Cherif [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Bose, Tanmoy [Indian Institute of Technology Kharagpur, Kharagpur 721302, West Bengal (India); Pekpe, Komi Midzodzi, E-mail: midzodzi.pekpe@univ-lille1.fr [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Cassar, Jean-Philippe [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Mohanty, A.R. [Indian Institute of Technology Kharagpur, Kharagpur 721302, West Bengal (India); Paumel, Kévin [CEA, DEN, Nuclear Technology Department, F-13108 Saint-Paul-lez-Durance (France)

    2014-10-15

    Highlights: • The work deals with sodium boiling detection in a liquid metal fast breeder reactor. • The authors choose to use acoustic data instead of thermal data. • The method is designed to not to be disturbed by the environment noises. • A real time boiling detection methods are proposed in the paper. - Abstract: This paper deals with acoustic monitoring of sodium boiling in a liquid metal fast breeder reactor (LMFBR) based on auto regressive (AR) models which have low computational complexities. Some authors have used AR models for sodium boiling or sodium–water reaction detection. These works are based on the characterization of the difference between fault free condition and current functioning of the system. However, even in absence of faults, it is possible to observe a change in the AR models due to the change of operating mode of the LMFBR. This sets up the delicate problem of how to distinguish a change in operating mode in absence of faults and a change due to presence of faults. In this paper we propose a new approach for boiling detection based on the estimation of AR models on sliding windows. Afterwards, classification of the models into boiling or non-boiling models is made by comparing their coefficients by two statistical methods, multiple linear regression (LR) and support vectors machines (SVM). The proposed approach takes into account operating mode information in order to avoid false alarms. Experimental data include non-boiling background noise data collected from Phenix power plant (France) and provided by the CEA (Commissariat à l’Energie Atomique et aux énergies alternatives, France) and boiling condition data generated in laboratory. High boiling detection rates as well as low false alarms rates obtained on these experimental data show that the proposed method is efficient for boiling detection. Most importantly, it shows that the boiling phenomenon introduces a disturbance into the AR models that can be clearly detected.

  14. Numerical prediction of nucleate pool boiling heat transfer coefficient under high heat fluxes

    OpenAIRE

    Pezo Milada L.; Stevanović Vladimir D.

    2016-01-01

    This paper presents CFD (Computational Fluid Dynamics) approach to prediction of the heat transfer coefficient for nucleate pool boiling under high heat fluxes. Three-dimensional numerical simulations of the atmospheric saturated pool boiling are performed. Mathematical modelling of pool boiling requires a treatment of vapor-liquid two-phase mixture on the macro level, as well as on the micro level, such as bubble growth and departure from the heating surfa...

  15. Transient measurement of temperature oscillation during noisy film boiling in superfluid helium II

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Noisy film boiling, which is characterized by a loud noise andsevere mechanical vibration, is a particular phenomenon of superfluid helium II (He II). Experiments have been conducted under various thermal conditions by varying the heating time th and the heat flux q, and the temperature oscillation during noisy film boiling is measured by the superconductor temperature sensors in order to understand the physical mechanism of noisy film boiling.

  16. EFFECTS OF LOCALIZED AQUIFER BOILING ON FLUID PRODUCTION AT CERRO PRIETO.

    Science.gov (United States)

    Truesdell, Alfred H.; D'Amore, Franco; Nieva, David

    1984-01-01

    Localized aquifer boiling in the shallow two-phase reservoir of Cerro Prieto has produced excess steam and increased electrical output. Unfortunately it has also caused near-well mineral deposition that has decreased permeability and fluid flow. Inflow of cold water has limited the extent of aquifer boiling and permeability loss. The deeper reservoir at Cerro Prieto may need injection of cold water to decrease boiling and prevent loss of production. Refs.

  17. Experimental Investigation of Coolant Boiling in a Half-Heated Circular Tube - Final CRADA Report

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Wenhua [Argonne National Lab. (ANL), Argonne, IL (United States); Singh, Dileep [Argonne National Lab. (ANL), Argonne, IL (United States); France, David M. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-11-01

    Coolant subcooled boiling in the cylinder head regions of heavy-duty vehicle engines is unavoidable at high thermal loads due to high metal temperatures. However, theoretical, numerical, and experimental studies of coolant subcooled flow boiling under these specific application conditions are generally lacking in the engineering literature. The objective of this project was to provide such much-needed information, including the coolant subcooled flow boiling characteristics and the corresponding heat transfer coefficients, through experimental investigations.

  18. Boiling heat transfer region with independence of the wall temperature

    Science.gov (United States)

    Mühlenbruch, G. H. D.; Schmidt, J.

    Extensive measurements of the intensive cooling of hot-rolled wires with temperatures between 1000 °C and 1100 °C are analysed. The analysis proves the existence of a convection-controlled boiling region, which has been previously observed by few authors in the case of high mass fluxes and high liquid subcooling. This region is characterised by an independence of the heat flux of the surface temperature. The heat flux depends essentially on the Reynolds number, the main influence parameter of the single phase convection, and on the liquid subcooling.

  19. Radon depletion in xenon boil-off gas

    OpenAIRE

    Bruenner, S.; Cichon, D.; Lindemann, S.; Undagoitia, T. Marrodán; Simgen, H.

    2016-01-01

    An important background in detectors using liquid xenon for rare event searches arises from the decays of radon and its daughters. We report for the first time a reduction of $^{222}$Rn in the gas phase above a liquid xenon reservoir. We show a reduction factor of $\\gtrsim 4$ for the $^{222}$Rn concentration in boil-off xenon gas compared to the radon enriched liquid phase. A semiconductor-based $\\alpha$-detector and miniaturized proportional counters are used to detect the radon. As the rado...

  20. Experimental research conception of thin liquid film boiling and evaporation

    Directory of Open Access Journals (Sweden)

    Feoktistov Dmitry V.

    2015-01-01

    Full Text Available The concept of conducting the experiments for studying thin liquid film boiling and evaporation was developed. Implementing this conception on developed experimental setup, we will obtain the data on the change of liquid film thickness in thermosiphon and temperature distribution in the liquid film, also the evaporation rate of liquid film and heat transfer coefficient change will be calculated using the measured values in the experiment. Three series of preliminary experiment were conducted. As a result, the main influencing factors and their values were defined.