WorldWideScience

Sample records for boiling chloride brines

  1. Modeling acid-gas generation from boiling chloride brines

    Directory of Open Access Journals (Sweden)

    Sonnenthal Eric

    2009-11-01

    Full Text Available Abstract Background This study investigates the generation of HCl and other acid gases from boiling calcium chloride dominated waters at atmospheric pressure, primarily using numerical modeling. The main focus of this investigation relates to the long-term geologic disposal of nuclear waste at Yucca Mountain, Nevada, where pore waters around waste-emplacement tunnels are expected to undergo boiling and evaporative concentration as a result of the heat released by spent nuclear fuel. Processes that are modeled include boiling of highly concentrated solutions, gas transport, and gas condensation accompanied by the dissociation of acid gases, causing low-pH condensate. Results Simple calculations are first carried out to evaluate condensate pH as a function of HCl gas fugacity and condensed water fraction for a vapor equilibrated with saturated calcium chloride brine at 50-150°C and 1 bar. The distillation of a calcium-chloride-dominated brine is then simulated with a reactive transport model using a brine composition representative of partially evaporated calcium-rich pore waters at Yucca Mountain. Results show a significant increase in boiling temperature from evaporative concentration, as well as low pH in condensates, particularly for dynamic systems where partial condensation takes place, which result in enrichment of HCl in condensates. These results are in qualitative agreement with experimental data from other studies. Conclusion The combination of reactive transport with multicomponent brine chemistry to study evaporation, boiling, and the potential for acid gas generation at the proposed Yucca Mountain repository is seen as an improvement relative to previously applied simpler batch evaporation models. This approach allows the evaluation of thermal, hydrological, and chemical (THC processes in a coupled manner, and modeling of settings much more relevant to actual field conditions than the distillation experiment considered. The actual

  2. Efficient acetylation of primary amines and amino acids in environmentally benign brine solution using acetyl chloride

    Indian Academy of Sciences (India)

    Kaushik Basu; Suchandra Chakraborty; Achintya Kumar Sarkar; Chandan Saha

    2013-05-01

    Acetyl chloride is one of the most commonly available and cheap acylating agent but its high reactivity and concomitant instability in water precludes its use to carry out acetylation in aqueous medium. The present methodology illustrates the efficient acetylation of primary amines and amino acids in brine solution by means of acetyl chloride under weakly basic condition in the presence of sodium acetate and/or triethyl amine followed by trituration with aqueous saturated bicarbonate solution. This effort represents the first efficient use of this most reactive but cheap acetylating agent to acetylate amines in excellent yields in aqueous medium. This is a potentially useful green chemical transformation where reaction takes place in environment-friendly brine solution leading to easy work-up and isolation of the amide derivatives. Mechanistic rationale of this methodology is also important.

  3. Repassivation Potential of Alloy 22 in Sodium and Calcium Chloride Brines

    Energy Technology Data Exchange (ETDEWEB)

    Rebak, R B; Ilevbare, G O; Carranza, R M

    2007-08-11

    A comprehensive matrix of 60 tests was designed to explore the effect of calcium chloride vs. sodium chloride and the ratio R of nitrate concentration over chloride concentration on the repassivation potential of Alloy 22. Tests were conducted using the cyclic potentiodynamic polarization (CPP) technique at 75 C and at 90 C. Results show that at a ratio R of 0.18 and higher nitrate was able to inhibit the crevice corrosion in Alloy 22 induced by chloride. Current results fail to show in a consistent way a different effect on the repassivation potential of Alloy 22 for calcium chloride solutions than for sodium chloride solutions.

  4. Radiolysis and corrosion of 238Pu-doped UO2 pellets in chloride brine

    Indian Academy of Sciences (India)

    M Kelm; E Bohnert

    2002-12-01

    Deaerated 5 M NaCl solution is irradiated in the presence of UO2 pellets with a-radiation from 238Pu. Experiments are conducted with 238Pu doped pellets and others with 238Pu dissolved in the brine. The radiolysis products and yields of mobilized U and Pu from the oxidative dissolution of UO2 are determined. Results found for radiolysis products and for the oxidation/dissolution of pellets immersed in Pu containing brine are similar to results for Pu doped pellets, where the radiation chemical processes occur only in the liquid layer of some 10 m thickness adjacent to the pellet. The yield of radiolysis products is comparable to earlier results, that of mobilized U from the pellets is < 1% of the total amount of oxidized species. Thus, the radiation chemical yield (-value) for mobilized hexavalent U is < 0.01 ions/100 eV. In spite of the low radiation yield for the corrosion, the rate of UO2 dissolution is higher than expected for the concentrations of long-lived oxidizing radiolysis compounds found in the solutions.

  5. Dissolution of nontronite in chloride brines and implications for the aqueous history of Mars

    Science.gov (United States)

    Steiner, M. H.; Hausrath, E. M.; Elwood Madden, M. E.; Tschauner, O.; Ehlmann, B. L.; Olsen, A. A.; Gainey, S. R.; Smith, J. S.

    2016-12-01

    Increasing evidence suggests the presence of recent liquid water, including brines, on Mars. Brines have therefore likely impacted clay minerals such as the Fe-rich mineral nontronite found in martian ancient terrains. To interpret these interactions, we conducted batch experiments to measure the apparent dissolution rate constant of nontronite at 25.0 °C at activities of water (aH2O) of 1.00 (0.01 M CaCl2 or NaCl), 0.75 (saturated NaCl or 3.00 mol kg-1 CaCl2), and 0.50 (5.00 mol kg-1 CaCl2). Experiments at aH2O = 1.00 (0.01 M CaCl2) were also conducted at 4.0 °C, 25.0 °C, and 45.0 °C to measure an apparent activation energy for the dissolution of nontronite. Apparent dissolution rate constants at 25.0 °C in CaCl2-containing solutions decrease with decreasing activity of water as follows: 1.18 × 10-12 ± 9 × 10-14 mol mineral m-2 s-1 (aH2O = 1.00) > 2.36 × 10-13 ± 3.1 × 10-14 mol mineral m-2 s-1 (aH2O = 0.75) > 2.05 × 10-14 ± 2.9 × 10-15 mol mineral m-2 s-1 (aH2O = 0.50). Similar results were observed at 25.0 °C in NaCl-containing solutions: 1.89 × 10-12 ± 1 × 10-13 mol mineral m-2 s-1 (aH2O = 1.00) > 1.98 × 10-13 ± 2.3 × 10-14 mol mineral m-2 s-1 (aH2O = 0.75). This decrease in apparent dissolution rate constants with decreasing activity of water follows a relationship of the form: log kdiss = 3.70 ± 0.20 × aH2O - 15.49, where kdiss is the apparent dissolution rate constant, and aH2O is the activity of water. The slope of this relationship (3.70 ± 0.20) is within uncertainty of that of other minerals where the relationship between dissolution rates and activity of water has been tested, including forsteritic olivine (log R = 3.27 ± 0.91 × aH2O - 11.00) (Olsen et al., 2015) and jarosite (log R = 3.85 ± 0.43 × aH2O - 12.84) (Dixon et al., 2015), where R is the mineral dissolution rate. This result allows prediction of mineral dissolution as a function of activity of water and suggests that with decreasing activity of water, mineral

  6. Standard test method for evaluating stress-corrosion cracking of stainless alloys with different nickel content in boiling acidified sodium chloride solution

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2000-01-01

    1.1 This test method describes a procedure for conducting stress-corrosion cracking tests in an acidified boiling sodium chloride solution. This test method is performed in 25% (by mass ) sodium chloride acidified to pH 1.5 with phosphoric acid. This test method is concerned primarily with the test solution and glassware, although a specific style of U-bend test specimen is suggested. 1.2 This test method is designed to provide better correlation with chemical process industry experience for stainless steels than the more severe boiling magnesium chloride test of Practice G36. Some stainless steels which have provided satisfactory service in many environments readily crack in Practice G36, but have not cracked during interlaboratory testing using this sodium chloride test method. 1.3 This boiling sodium chloride test method was used in an interlaboratory test program to evaluate wrought stainless steels, including duplex (ferrite-austenite) stainless and an alloy with up to about 33% nickel. It may also b...

  7. Influence of brine concentration on sugar and sodium chloride diffusion during the processing of the green olive variety Arauco

    Directory of Open Access Journals (Sweden)

    Miras, N.

    2008-09-01

    Full Text Available The green olive variety Arauco were debittered using lye concentrations of, 2.50% NaOH.They were then subjected to two rinsing processes with tap water. Next, the olives were cured with brines at 7%, 10% and 13% sodium chloride concentration. During this curing process, the loss of reducing sugars from the olives, and the diffusion of sodium chloride into the olives were quantified. Effective diffusion coefficients of both solutes in the skin and the flesh were calculated for this period using a diffusion model for a composite hollow sphere. The skin effective diffusion coefficients for both solutes ranged from entre 8,27x10-14- m2/s to 4,04x10-13 m2/s. The flesh coefficients varied from 2,92x10-9 m2/s to 3,99x10-9 m2/s for sodium chloride and from 9,76x10-11 m2/s to 2,22x10-10 m2/s for reducing sugars.Aceitunas verdes variedad Arauco fueron tratadas con soluciones de hidróxido de sodio al 2,5%. Estas fueron luego sometidas a dos procesos de lavado con agua corriente. Posteriormente, las aceitunas fueron curadas en salmueras con concentraciones de 7%, 10% y 13% de cloruro de sodio. Durante este proceso de curado, se cuantificó la pérdida de azúcares reductores desde, y la difusión de cloruro de sodio hacia el interior de las aceitunas. Durante este período se calcularon los coeficientes efectivos de difusión de ambos solutos en la piel y la pulpa, utilizando un modelo de difusión en una esfera hueca compuesta. Los coeficientes efectivos de difusión de ambos solutos en la piel estuvieron en un rango entre 8,27x10-14- m2/s y 4,04x10-13 m2/s. Los coeficientes de la pulpa variaron entre 2,92x10-9 m2/s y 3,99x10-9 m2/s para el cloruro de sodio, y entre 9,76x10-11 m2/s y 2,22x10-10 m2/s para los azúcares reductores.

  8. Forward Osmosis Brine Drying

    Science.gov (United States)

    Flynn, Michael; Shaw, Hali; Hyde, Deirdre; Beeler, David; Parodi, Jurek

    2015-01-01

    The Forward Osmosis Brine Drying (FOBD) system is based on a technique called forward osmosis (FO). FO is a membrane-based process where the osmotic potential between brine and a salt solution is equalized by the movement of water from the brine to the salt solution. The FOBD system is composed of two main elements, the FO bag and the salt regeneration system. This paper discusses the results of testing of the FO bag to determine the maximum water recovery ratio that can be attained using this technology. Testing demonstrated that the FO bag is capable of achieving a maximum brine water recovery ratio of the brine of 95%. The equivalent system mass was calculated to be 95 kg for a feed similar to the concentrated brine generated on the International Space Station and 86 kg for an Exploration brine. The results have indicated that the FOBD can process all the brine for a one year mission for between 11% to 10% mass required to bring the water needed to make up for water lost in the brine if not recycled. The FOBD saves 685 kg and when treating the International Space Station brine and it saves 829 kg when treating the Exploration brine. It was also demonstrated that saturated salt solutions achieve a higher water recovery ratios than solids salts do and that lithium chloride achieved a higher water recovery ratio than sodium chloride.

  9. Brines formed by multi-salt deliquescence

    Energy Technology Data Exchange (ETDEWEB)

    Carroll, S; Rard, J; Alai, M; Staggs, K

    2005-11-04

    The FY05 Waste Package Environment testing program at Lawrence Livermore National Laboratory focused on determining the temperature, relative humidity, and solution compositions of brines formed due to the deliquescence of NaCl-KNO{sub 3}-NaNO{sub 3} and NaCl-KNO{sub 3}-NaNO{sub 3}-Ca(NO{sub 3}){sub 2} salt mixtures. Understanding the physical and chemical behavior of these brines is important because they define conditions under which brines may react with waste canister surfaces. Boiling point experiments show that NaCl-KNO{sub 3}-NaNO{sub 3} and NaCl-KNO{sub 3}-NaNO{sub 3}-Ca(NO{sub 3}){sub 2} salt mixtures form brines that transform to hydrous melts that do not truly 'dry out' until temperatures exceed 300 and 400 C, respectively. Thus a conducting solution is present for these salt assemblages over the thermal history of the repository. The corresponding brines form at lower relative humidity at higher temperatures. The NaCl-KNO{sub 3}-NaNO{sub 3} salt mixture has a mutual deliquescence relative humidity (MDRH) of 25.9% at 120 C and 10.8% at 180 C. Similarly, the KNO{sub 3}-NaNO{sub 3} salt mixture has MDRH of 26.4% at 120 C and 20.0% at 150 C. The KNO{sub 3}-NaNO{sub 3} salt mixture salts also absorb some water (but do not appear to deliquesce) at 180 C and thus may also contribute to the transfer of electrons at interface between dust and the waste package surface. There is no experimental evidence to suggest that these brines will degas and form less deliquescent salt assemblages. Ammonium present in atmospheric and tunnel dust (as the chloride, nitrate, or sulfate) will readily decompose in the initial heating phase of the repository, and will affect subsequent behavior of the remaining salt mixture only through the removal of a stoichiometric equivalent of one or more anions. Although K-Na-NO{sub 3}-Cl brines form at high temperature and low relative humidity, these brines are dominated by nitrate, which is known to inhibit corrosion at lower

  10. Preparation of Basic Magnesium Chloride Whiskers from Xuwen Salt Field Brine%徐闻盐场苦卤制备碱式氯化镁晶须

    Institute of Scientific and Technical Information of China (English)

    吴健松; 梁海群

    2015-01-01

    The basic magnesium chloride whiskers with good whisker quality and smooth surface were synthesized by liquid precipitation reaction method using Xuwen salt field brine as raw materials and sodi-um hydroxide as the precipitant.The phase, purity, structure of crystal morphology, crystal growth orien-tationof whiskers samples were characterized by elementary analysis, X-ray diffraction ( XRD) , scanning electron microscopy ( SEM) and high resolution transmission electron microscopy ( HRTEM) .The SEM analysis revealed that the basic magnesium chloride whiskers showed fine dispersive capability, and the distribution of particle sizes was uniformity.The basic magnesium chloride whiskers with a well-defined shape as well as well straight whisker could be obtained under the following conditions:reaction tempera-ture of 35 ℃, and reaction time of 50 h.The preparation method is simple, and the production cost is low in this work.It is thus expected to use Xuwen salt field brine to a large-scale experiment.%以广东徐闻盐场苦卤为原料,氢氧化钠为沉淀剂,采用液相沉淀法制备了晶形好、分散性好的碱式氯化镁晶须。通过元素分析、 XRD、 SEM及HRTEM测试等手段分别表征了产品的纯度、属性、形貌特征及晶体生长取向。实验发现当反应温度T=35℃,反应时间t=50 h时可获得直晶率好、分散性好的碱式氯化镁晶须。扫描电镜示碱式氯化镁晶须粒度分布均匀、分散性好。本实验不仅生产工艺简单,且生产成本低,可望利用徐闻盐场苦卤进一步中试。

  11. Texture and antioxidant evolution of naturally green table olives as affected by different sodium chloride brine concentrations

    Directory of Open Access Journals (Sweden)

    Fadda, C.

    2014-03-01

    Full Text Available The results on the evolution of the texture and antioxidant activity during the processing of naturally fermented green olives are reported in the present study. The olives were brined with two different NaCl concentrations, 4 and 7%. A puncture test and a texture profile analysis (TPA test were carried out to evaluate texture, while the antioxidant activity was assessed in consideration of the loss of absorbance of a stable radical upon reaction with a polyphenolic olive extract. The puncture test revealed both an increase and decrease in peel and flesh hardness, respectively. The olives processed with 7% NaCl concentration showed higher peel hardness than olives brined with 4% salt. The texture profile analysis did not reveal any difference between the two salt concentrations used, but showed a decrease in the value of all parameters after 30 days of brining. The antioxidant activity of the polyphenolic extract decreased significantly during processing, with a major loss after the first 30 days of processing and was higher in the 7% brined olives, than the sample treated with 4% NaCl.En este trabajo se presentan los resultados sobre la evolución de la textura y la actividad antioxidante durante el proceso de fermentación natural de las aceitunas verdes. Los frutos se colocaron en salmueras con dos concentraciones de NaCl del 4% y 7%. Se evaluó la textura mediante ensayo de perforación y mediante análisis de perfil de textura (TPA, mientras que la actividad antioxidante se evaluó considerando la pérdida de absorbancia de un radical estable tras la reacción con un extracto polifenólico de las aceitunas. El ensayo de perforación reveló un aumento de la dureza de la piel y una reducción en la dureza de la pulpa. Las aceitunas procesadas con una concentración de NaCl del 7% mostraron una dureza mayor que aquellas tratadas con sal al 4%. El análisis del perfil de la textura no reveló diferencias entre las dos concentraciones usadas de

  12. Preparation and Characteristics of Polyaluminium Chloride by Utilizing Fluorine-Containing Waste Acidic Mother Liquid from Clay-Brine Synthetic Cryolite Process

    Directory of Open Access Journals (Sweden)

    Feng-shan Zhou

    2014-01-01

    Full Text Available Clay-brine process employing activated clay, NaCl, HCl, and HF as raw materials is the primarily advanced technology to synthesize cryolite in the present industrial grade. However, plenty of byproducts of fluorine-containing waste HCl at the concentration of about 10%~12% could not be utilized comprehensively and are even hazardous to the environment. This work proposed a new two-step technology to prepare inorganic polymer flocculants polyaluminium chloride (PAC from synthetic cryolite mother liquor. Many specific factors such as the variety of aluminide source, reaction temperature and time, reagent ratio, and manner of alkaline addition were taken into consideration and their influences on the performances of produced PAC were discussed. It was found that synthetic cryolite mother liquor could react with bauxite and calcium aluminate directly to prepare cheap PAC, with plenty amount of water insoluble CaF2 and CaSiF6 produced as well. However, once HCl was introduced into synthetic cryolite mother liquor as well as by utilizing bauxite as aluminide source and sodium aluminate as adjusting basicity agent, the resultant PAC would dissolve out higher amount of aluminum while producing little amount of water insoluble materials. The coagulation behavior of the specially produced PAC could even match the industrial grade PAC conforming to national standard.

  13. The Formation of Liquid Water on Present-Day Mars: Calcium-Magnesium Chloride Brines in the Antarctic Dry Valleys as a Mars Analog

    Science.gov (United States)

    Toner, J. D.; Catling, D. C.

    2016-09-01

    By analogy to the Antarctic Dry Valleys, Ca-Mg-Cl brines may be responsible for aqueous flows on Mars. We use modeling to show that Ca-Mg-Cl brines could be stable on Mars, and are often more favorable for forming solutions than perchlorate salts.

  14. Ion association in natural brines

    Science.gov (United States)

    Truesdell, A.H.; Jones, B.F.

    1969-01-01

    Natural brines, both surface and subsurface, are highly associated aqueous solutions. Ion complexes in brines may be ion pairs in which the cation remains fully hydrated and the bond between the ions is essentially electrostatic, or coordination complexes in which one or more of the hydration water molecules are replaced by covalent bonds to the anion. Except for Cl-, the major simple ions in natural brines form ion pairs; trace and minor metals in brines form mainly coordination complexes. Limitations of the Debye-Hu??ckel relations for activity coefficients and lack of data on definition and stability of all associated species in concentrated solutions tend to produce underestimates of the degree of ion association, except where the brines contain a very high proportion of Cl-. Data and calculations on closed basin brines of highly varied composition have been coupled with electrode measurements of single-ion activities in an attempt to quantify the degree of ion association. Such data emphasize the role of magnesium complexes. Trace metal contents of closed basin brines are related to complexes formed with major anions. Alkaline sulfo- or chlorocarbonate brines (western Great Basin) carry significant trace metal contents apparently as hydroxides or hydroxy polyions. Neutral high chloride brines (Bonneville Basin) are generally deficient in trace metals. With a knowledge of the thermodynamic properties of a natural water, many possible reactions with other phases (solids, gases, other liquids) may be predicted. A knowledge of these reactions is particularly important in the study of natural brines which may be saturated with many solid phases (silicates, carbonates, sulfates, etc.), which may have a high pH and bring about dissolution of other phases (silica, amphoteric hydroxides, CO2, etc.), and which because of their high density may form relatively stable interfaces with dilute waters. ?? 1969.

  15. Study and Test of Process of Production of Potassium Chloride from High Calcium Potassium Bearing Brine in Salt Lake%利用盐湖高钙含钾卤水制取氯化钾工艺试验研究

    Institute of Scientific and Technical Information of China (English)

    朱晓东; 郑秀洁

    2011-01-01

    In some of chloride - type brine in Salt Lake of Qinghai. The cycling accumulation of calcium results in increasing growth of its concetration, which probably will make some effect on the production of potassium chloride from brine. This paper makes research on impact this type of high calcium potassium bearing brine has on production of potassium chloride by 4# Process . The research results show that calcium content in brine would have less impact on production of potassium chloride by 4# Process.%青海盐湖部分氯化物型卤水中,由于钙的循环积累,其浓度不断增高,这可能对从卤水中提取氯化钾带来一定影响.实验研究了该类型高钙含钾卤水对4#工艺制取氯化钾的影响,研究结果表明卤水中钙含量对4#工艺制取氯化钾影响较小.

  16. Understanding the Risk of Chloride Induced Stress Corrosion Cracking of Interim Storage Containers for the Dry Storage of Spent Nuclear Fuel: Evolution of Brine Chemistry on the Container Surface.

    Energy Technology Data Exchange (ETDEWEB)

    Enos, David; Bryan, Charles R.

    2015-10-01

    Although the susceptibility of austenitic stainless steels to chloride-induced stress corrosion cracking is well known, uncertainties exist in terms of the environmental conditions that exist on the surface of the storage containers. While a diversity of salts is present in atmospheric aerosols, many of these are not stable when placed onto a heated surface. Given that the surface temperature of any container storing spent nuclear fuel will be well above ambient, it is likely that salts deposited on its surface may decompose or degas. To characterize this effect, relevant single and multi-salt mixtures are being evaluated as a function of temperature and relative humidity to establish the rates of degassing, as well as the likely final salt and brine chemistries that will remain on the canister surface.

  17. Recycling of tail gas from low boiling tower for calcium carbide-process vinyl chloride rectification%电石法氯乙烯精馏低塔尾气的利用

    Institute of Scientific and Technical Information of China (English)

    唐复兴

    2012-01-01

    以40万t/a电石法聚氯乙烯装置为例,对氯乙烯精馏低塔尾气回收进行了详细的计算,表明以变压吸附的方法综合回收精馏尾气可获得显著的经济效益。%The recycling of tail gas from low boiling tower for vinyl chloride rectification for 400 kt/a plant of calcium carbide-process PVC is calculated in detail. It is shown that the recycling of these tail gas by adopting pressure swing adsorption method can obtain great economic benefits.

  18. Technology Analysis on Co-production of Soda Ash and Ammonium Chloride with Glauber's Brine by Thermal Cycling Method%芒硝型卤水热循环法联产纯碱与氯化铵工艺研究分析

    Institute of Scientific and Technical Information of China (English)

    彭赛军; 彭志成

    2014-01-01

    卤水生产纯碱主要为氨碱法,侯氏联碱法生产纯碱和氯化铵采用固体盐为原料;本文提出新的申请专利技术工艺,采用卤水直接为原料生产纯碱和氯化铵,供同行参考。%Primarily for the production of soda ash with brine is ammonia soda method. Hou's metohd takes solid salt as the raw material to produce soda ash and ammonium chloride. This paper presents a new patented technology process which produce soda ash and ammonium chloride directly with brine as the raw material.

  19. Oscillate Boiling

    CERN Document Server

    Li, Fenfang; Nguyen, Dang Minh; Ohl, Claus-Dieter

    2016-01-01

    We report about an intriguing boiling regime occurring for small heaters embedded on the boundary in subcooled water. The microheater is realized by focusing a continuous wave laser beam to about $10\\,\\mu$m in diameter onto a 165\\,nm-thick layer of gold, which is submerged in water. After an initial vaporous explosion a single bubble oscillates continuously and repeatably at several $100\\,$kHz. The microbubble's oscillations are accompanied with bubble pinch-off leading to a stream of gaseous bubbles into the subcooled water. The self-driven bubble oscillation is explained with a thermally kicked oscillator caused by the non-spherical collapses and by surface pinning. Additionally, Marangoni stresses induce a recirculating streaming flow which transports cold liquid towards the microheater reducing diffusion of heat along the substrate and therefore stabilizing the phenomenon to many million cycles. We speculate that this oscillate boiling regime may allow to overcome the heat transfer thresholds observed dur...

  20. Lithium isotope geochemistry and origin of Canadian shield brines.

    Science.gov (United States)

    Bottomley, D J; Chan, L H; Katz, A; Starinsky, A; Clark, I D

    2003-01-01

    Hypersaline calcium/chloride shield brines are ubiquitous in Canada and areas of northern Europe. The major questions relating to these fluids are the origin of the solutes and the concentration mechanism that led to their extreme salinity. Many chemical and isotopic tracers are used to solve these questions. For example, lithium isotope systematics have been used recently to support a marine origin for the Yellowknife shield brine (Northwest Territories). While having important chemical similarities to the Yellowknife brine, shield brines from the Sudbury/Elliot Lake (Ontario) and Thompson/Snow Lake (Manitoba) regions, which are the focus of this study, exhibit contrasting lithium behavior. Brine from the Sudbury Victor mine has lithium concentrations that closely follow the sea water lithium-bromine concentration trajectory, as well as delta6Li values of approximately -28/1000. This indicates that the lithium in this brine is predominantly marine in origin with a relatively minor component of crustal lithium leached from the host rocks. In contrast, the Thompson/Snow Lake brine has anomalously low lithium concentrations, indicating that it has largely been removed from solution by alteration minerals. Furthermore, brine and nonbrine mine waters at the Thompson mine have large delta6Li variations of approximately 30/1000, which primarily reflects mixing between deep brine with delta6Li of -35 +/- 2/1000 and near surface mine water that has derived higher delta6Li values through interactions with their host rocks. The contrary behavior of lithium in these two brines shows that, in systems where it has behaved conservatively, lithium isotopes can distinguish brines derived from marine sources.

  1. Results for the Brine Evaporation Bag (BEB) Brine Processing Test

    Science.gov (United States)

    Delzeit, Lance; Flynn, Michael; Fisher, John; Shaw, Hali; Kawashima, Brian; Beeler, David; Howard, Kevin

    2015-01-01

    The recent Brine Processing Test compared the NASA Forward Osmosis Brine Dewatering (FOBD), Paragon Ionomer Water Processor (IWP), UMPQUA Ultrasonic Brine Dewatering System (UBDS), and the NASA Brine Evaporation Bag (BEB). This paper reports the results of the BEB. The BEB was operated at 70 deg C and a base pressure of 12 torr. The BEB was operated in a batch mode, and processed 0.4L of brine per batch. Two different brine feeds were tested, a chromic acid-urine brine and a chromic acid-urine-hygiene mix brine. The chromic acid-urine brine, known as the ISS Alternate Pretreatment Brine, had an average processing rate of 95 mL/hr with a specific power of 5kWhr/L. The complete results of these tests will be reported within this paper.

  2. Geochemical implications of brine leakage into freshwater aquifers.

    Science.gov (United States)

    Wunsch, Assaf; Navarre-Sitchler, Alexis K; McCray, John E

    2013-01-01

    CO(2) injection into deep saline formations as a way to mitigate climate change raises concerns that leakage of saline waters from the injection formations will impact water quality of overlying aquifers, especially underground sources of drinking water (USDWs). This paper aims to characterize the geochemical composition of deep brines, with a focus on constituents that pose a human health risk and are regulated by the U.S. Environmental Protection Agency (USEPA). A statistical analysis of the NATCARB brine database, combined with simple mixing model calculations, show total dissolved solids and concentrations of chloride, boron, arsenic, sulfate, nitrate, iron and manganese may exceed plant tolerance or regulatory levels. Twelve agricultural crops evaluated for decreased productivity in the event of brine leakage would experience some yield reduction due to increased TDS at brine-USDW ratios of United States are almost three times higher than public and domestic withdrawals.

  3. Evaporation, Boiling and Bubbles

    Science.gov (United States)

    Goodwin, Alan

    2012-01-01

    Evaporation and boiling are both terms applied to the change of a liquid to the vapour/gaseous state. This article argues that it is the formation of bubbles of vapour within the liquid that most clearly differentiates boiling from evaporation although only a minority of chemistry textbooks seems to mention bubble formation in this context. The…

  4. Aspects of subcooled boiling

    Energy Technology Data Exchange (ETDEWEB)

    Bankoff, S.G. [Northwestern Univ., Evanston, IL (United States)

    1997-12-31

    Subcooled boiling boiling refers to boiling from a solid surface where the bulk liquid temperature is below the saturation temperature (subcooled). Two classes are considered: (1) nucleate boiling, where, for large subcoolings, individual bubbles grow and collapse while remaining attached to the solid wall, and (2) film boiling, where a continuous vapor film separates the solid from the bulk liquid. One mechanism by which subcooled nucleate boiling results in very large surface heat transfer coefficient is thought to be latent heat transport within the bubble, resulting from simultaneous evaporation from a thin residual liquid layer at the bubble base, and condensation at the polar bubble cap. Another is the increased liquid microconvection around the oscillating bubble. Two related problems have been attacked. One is the rupture of a thin liquid film subject to attractive and repulsive dispersion forces, leading to the formation of mesoscopic drops, which then coalesce and evaporate. Another is the liquid motion in the vicinity of an oscillating contact line, where the bubble wall is idealized as a wedge of constant angle sliding on the solid wall. The subcooled film boiling problem has been attacked by deriving a general long-range nonlinear evolution equation for the local thickness of the vapor layer. Linear and weakly-nonlinear stability results have been obtained. A number of other related problems have been attacked.

  5. Treatment methods for geothermal brines

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, S.L.; Mathur, A.K.; Garrison, W.

    1979-04-01

    A survey is made of commercially available methods currently in use as well as those which might be used to prevent scaling and corrosion in geothermal brines. More emphasis is placed on scaling. Treatments are classified as inhibitors, alterants and coagulants; they are applied to control scaling and corrosion in fresh and waste geothermal brines. Recommendations for research in brine treatment are described.

  6. Brine Distribution after Vacuum Saturation

    DEFF Research Database (Denmark)

    Hedegaard, Kathrine; Andersen, Bertel Lohmann

    1999-01-01

    Experiments with the vacuum saturation method for brine in plugs of chalk showed that a homogeneous distribution of brine cannot be ensured at saturations below 20% volume. Instead of a homogeneous volume distribution the brine becomes concentrated close to the surfaces of the plugs...

  7. Brine Transport Experiments in Granular Salt

    Energy Technology Data Exchange (ETDEWEB)

    Jordan, Amy B. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Boukhalfa, Hakim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Caporuscio, Florie Andre [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stauffer, Philip H. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-06-06

    To gain confidence in the predictive capability of numerical models, experimental validation must be performed to ensure that parameters and processes are correctly simulated. The laboratory investigations presented herein aim to address knowledge gaps for heat-generating nuclear waste (HGNW) disposal in bedded salt that remain after examination of prior field and laboratory test data. Primarily, we are interested in better constraining the thermal, hydrological, and physicochemical behavior of brine, water vapor, and salt when moist salt is heated. The target of this work is to use run-of-mine (RoM) salt; however during FY2015 progress was made using high-purity, granular sodium chloride.

  8. Nucleate boiling heat transfer

    Energy Technology Data Exchange (ETDEWEB)

    Saiz Jabardo, J.M. [Universidade da Coruna (Spain). Escola Politecnica Superior], e-mail: mjabardo@cdf.udc.es

    2009-07-01

    Nucleate boiling heat transfer has been intensely studied during the last 70 years. However boiling remains a science to be understood and equated. In other words, using the definition given by Boulding, it is an 'insecure science'. It would be pretentious of the part of the author to explore all the nuances that the title of the paper suggests in a single conference paper. Instead the paper will focus on one interesting aspect such as the effect of the surface microstructure on nucleate boiling heat transfer. A summary of a chronological literature survey is done followed by an analysis of the results of an experimental investigation of boiling on tubes of different materials and surface roughness. The effect of the surface roughness is performed through data from the boiling of refrigerants R-134a and R-123, medium and low pressure refrigerants, respectively. In order to investigate the extent to which the surface roughness affects boiling heat transfer, very rough surfaces (4.6 {mu}m and 10.5 {mu}m ) have been tested. Though most of the data confirm previous literature trends, the very rough surfaces present a peculiar behaviour with respect to that of the smoother surfaces (Ra<3.0 {mu}m). (author)

  9. The origin of the Cerro Prieto geothermal brine

    Science.gov (United States)

    Truesdell, A.H.; Thompson, J.M.; Coplen, T.B.; Nehring, N.L.; Janik, C.J.

    1981-01-01

    The Cerro Prieto geothermal brine may have originated from mixing of Colorado River water with seawater evaporated to about six times its normal salinity. This mixture circulated deeply and was heated by magmatic processes. During deep circulation, Li, K, Ca, B, SiO2 and rare alkalis were transferred from rock minerals to the water, and Mg, SO4, and a minor quantity of Na were transferred to the rock. Similar alteration of seawater salt chemistry has been observed in coastal geothermal systems and produced in laboratory experiments. After heating and alteration the brine was further diluted to its present range of composition. Oxygen isotopes in the fluid are in equilibrium with reservoir calcite and have been affected by exploitation-induced boiling and dilution. ?? 1981.

  10. Analysis of anions in geological brines using ion chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Merrill, R.M.

    1985-03-01

    Ion chromatographic procedures for the determination of the anions bromide, sulfate, nitrite, nitrate, phosphate, and iodide in brine samples have been developed and are described. The techniques have been applied to the analysis of natural brines, and geologic evaporites. Sample matrices varied over a range from 15,000 mg/L to 200,000 mg/L total halogens, nearly all of which is chloride. The analyzed anion concentrations ranged from less than 5 mg/L in the cases of nitrite, nitrate, and phosphate, to 20,000 mg/L in the case of sulfate. A technique for suppressing chloride and sulfate ions to facilitate the analysis of lower concentration anions is presented. Analysis times are typically less than 20 minutes for each procedure and the ion chromatographic results compare well with those obtained using more time consuming classical chemical analyses. 10 references, 14 figures.

  11. Numerical Investigation of Boiling

    Science.gov (United States)

    Sagan, Michael; Tanguy, Sebastien; Colin, Catherine

    2012-11-01

    In this work, boiling is numerically investigated, using two phase flow direct numerical simulation based on a level set / Ghost Fluid method. Nucleate boiling implies both thermal issue and multiphase dynamics issues at different scales and at different stages of bubble growth. As a result, the different phenomena are investigated separately, considering their nature and the scale at which they occur. First, boiling of a static bubble immersed in an overheated liquid is analysed. Numerical simulations have been performed at different Jakob numbers in the case of strong density discontinuity through the interface. The results show a good agreement on bubble radius evolution between the theoretical evolution and numerical simulation. After the validation of the code for the Scriven test case, interaction of a bubble with a wall is studied. A numerical method taking into account contact angle is evaluated by comparing simulations of the spreading of a liquid droplet impacting on a plate, with experimental data. Then the heat transfer near the contact line is investigated, and simulations of nucleate boiling are performed considering different contact angles values. Finally, the relevance of including a model to take into account the evaporation of the micro layer is discussed.

  12. Characterization of a soil contaminated by oilfield brine

    Energy Technology Data Exchange (ETDEWEB)

    Al-Mutairi, K.; Harris, T. [Univ. of Tulsa, OH (United States)

    1995-12-01

    Brine contamination of soil is a common environmental problem associated with the onshore production of oil and gas. A site of extensive contamination in Oklahoma has been characterized using conductimetry, direct potentiometry (pH- and chloride-selective electrodes), and atomic absorption spectrophotometry (for Na{sup +} and Ca{sup 2+}) to determine the extent of the contamination and the efficacy of various remediation technologies.

  13. Effects of Sodium Sulfate and Sodium Chloride on Ca2+ , Mg2+ Removal from Glauber Type Brine by Sodium Hydroxide and Sodium Carbonate%芒硝型卤水中盐硝组分对碱法脱除钙镁的影响

    Institute of Scientific and Technical Information of China (English)

    董泽亮; 张琦; 王俐聪; 蔡荣华; 马来波; 黄西平

    2013-01-01

    Ca2+ 、Mg2+ removal from Glauber type brine by sodium hydroxide and sodium carbonate has been studied.The effects of sodium sulfate and sodium chloride on removal efficiency of Ca2+,Mg2+ at room temperature were investigated in detail when addition amount of sodium hydroxide and sodium carbonate was theoretical value,reaction time was 30 min,aging time was 60 min.The experimental results show that the presence of sodium sulfate has large effect on removal efficiency of Ca2+.The removal rate of Ca2+ is more than 90% when the concentration of sodium sulfate is below 30 g/L.The presence of sodium sulfate has good but little effect on removal efficiency of Mg2+.The presence of sodium chloride has small effect on removal efficiency of Ca2+ and Mg2+.When the concentration of sodium chloride increases,the removal rate of Ca2+ increases significantly,but the removal rate of Mg2+ declines slightly.%采用“烧碱-纯碱”法,对芒硝型卤水中Ca2+和Mg2+的脱除进行了研究,在常温、两碱用量为理论用量、反应时间为30 min和陈化时间为60 min的条件下详细考察了卤水中氯化钠和硫酸钠含量的变化对Ca2+和Mg2脱除效果的影响.结果表明,硫酸钠组分对Ca2+的脱除效果影响较大,当硫酸钠含量在30 g/L以下时,Ca2+脱除率在90%以上,硫酸钠浓度增加有利于Mg2+的脱除,但影响不大.氯化钠组分对Ca2、Mg2+脱除效果的影响相对较小,氯化钠含量增加,Ca2+脱除率明显增加,而Mg2+脱除率略有下降.

  14. Geysering in boiling channels

    Energy Technology Data Exchange (ETDEWEB)

    Aritomi, Masanori; Takemoto, Takatoshi [Tokyo Institute of Technology, Tokyo (Japan); Chiang, Jing-Hsien [Japan NUS Corp. Ltd., Toyko (Japan)] [and others

    1995-09-01

    A concept of natural circulation BWRs such as the SBWR has been proposed and seems to be promising in that the primary cooling system can be simplified. The authors have been investigating thermo-hydraulic instabilities which may appear during the start-up in natural circulation BWRs. In our previous works, geysering was investigated in parallel boiling channels for both natural and forced circulations, and its driving mechanism and the effect of system pressure on geysering occurrence were made clear. In this paper, geysering is investigated in a vertical column and a U-shaped vertical column heated in the lower parts. It is clarified from the results that the occurrence mechanism of geysering and the dependence of system pressure on geysering occurrence coincide between parallel boiling channels in circulation systems and vertical columns in non-circulation systems.

  15. Oscillate boiling from microheaters

    Science.gov (United States)

    Li, Fenfang; Gonzalez-Avila, S. Roberto; Nguyen, Dang Minh; Ohl, Claus-Dieter

    2017-01-01

    We report about an intriguing boiling regime occurring for small heaters embedded on the boundary in subcooled water. The microheater is realized by focusing a continuous wave laser beam to about 10 μ m in diameter onto a 165-nm-thick layer of gold, which is submerged in water. After an initial vaporous explosion a single bubble oscillates continuously and repeatedly at several 100 kHz albeit with constant laser power input. The microbubble's oscillations are accompanied with bubble pinch-off, leading to a stream of gaseous bubbles in the subcooled water. The self-driven bubble oscillation is explained with a thermally kicked oscillator caused by surface attachment and by the nonspherical collapses. Additionally, Marangoni stresses induce a recirculating streaming flow which transports cold liquid towards the microheater, reducing diffusion of heat along the substrate and therefore stabilizing the phenomenon to many million cycles. We speculate that this oscillate boiling regime may overcome the heat transfer thresholds observed during the nucleate boiling crisis and offers a new pathway for heat transfer under microgravity conditions.

  16. Boiling incipience and convective boiling of neon and nitrogen

    Science.gov (United States)

    Papell, S. S.; Hendricks, R. C.

    1977-01-01

    Forced convection and subcooled boiling heat transfer data for liquid nitrogen and liquid neon were obtained in support of a design study for a 30 tesla cryomagnet cooled by forced convection of liquid neon. This design precludes nucleate boiling in the flow channels as they are too small to handle vapor flow. Consequently, it was necessary to determine boiling incipience under the operating conditions of the magnet system. The cryogen data obtained over a range of system pressures, fluid flow rates, and applied heat fluxes were used to develop correlations for predicting boiling incipience and convective boiling heat transfer coefficients in uniformly heated flow channels. The accuracy of the correlating equations was then evaluated. A technique was also developed to calculate the position of boiling incipience in a uniformly heated flow channel. Comparisons made with the experimental data showed a prediction accuracy of plus or minus 15 percent

  17. Difusão do cloreto de sódio no processo de salga de queijos: modelagem matemática com o emprego do método de elementos finitos The sodium chlorid diffusion during cheese brining: matematical model applying the finite element method

    Directory of Open Access Journals (Sweden)

    Rui Sérgio Ferreira SILVA

    1998-04-01

    Full Text Available A transferência de um soluto (cloreto de sódio, através de uma matriz sólida tridimensional (queijo foi estudada aplicando-se o método de elementos finitos. A formulação variacional (Galerkin do problema diferencial (modelo de difusão teve como base teórica a 2ª lei de Fick. Os procedimentos para integração no tempo foram o de Crank-Nicolson e o de Euler-modificado, que foram escolhidos por apresentarem estabilidade incondicional. O programa computacional desenvolvido mostrou-se versátil para resolver situações de amostragem em condições mais realistas e pode ser aplicado para geometrias complexas. O modelo proposto permitiu uma boa estimativa do ganho de sal no queijo, usando um coeficiente de difusão cujo valor pode ser obtido por extrapolação de dados experimentais. A aplicação do método numérico (MEF, com o esquema de Crank-Nicolson, na simulação da difusão do cloreto de sódio na salga de queijos, mostrou boa aproximação quando os resultados foram comparados com os valores experimentais encontrados na literatura especializada.Solute (sodium chloride transference through a three-dimensional matrix (cheese was studied applying the finite element method (MEF. The variational formulation (Galerkin of the differential problem (diffusion model had as the theoretical basis Fick’s second law. The methods for time integration were developed according to Crank-Nicolson (central difference, and modified Euler (backward difference, which presented unconditional stability. The computational program proved to be versatile in solving sampling situations in realistic condition and can be used in complex geometry. The proposed method gave good estimation of salt gain in the cheese when using a diffusion coefficient which value can be calculated by extrapolation of experimental data. The application of numeric method (MEF, with Crank-Nicolson scheme, in the simulation of diffusion of sodium chloride in the brining showed to be

  18. Enhanced Brine Dewatering System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The purpose of the Enhanced Brine Dewatering System (EBDS) is to provide an easily scalable means of completely recovering usable water from byproducts created by...

  19. Enhanced Brine Dewatering System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The purpose of the Enhanced Brine Dewatering System (EBDS) is to provide a scalable means of completely recovering usable water from byproducts created by reverse...

  20. Membrane Cells for Brine Electrolysis.

    Science.gov (United States)

    Tingle, M.

    1982-01-01

    Membrane cells were developed as alternatives to mercury and diaphragm cells for the electrolysis of brine. Compares the three types of cells, focusing on the advantages and disadvantages of membrane cells. (JN)

  1. Selective oxidation of bromide in wastewater brines from hydraulic fracturing.

    Science.gov (United States)

    Sun, Mei; Lowry, Gregory V; Gregory, Kelvin B

    2013-07-01

    Brines generated from oil and natural gas production, including flowback water and produced water from hydraulic fracturing of shale gas, may contain elevated concentrations of bromide (~1 g/L). Bromide is a broad concern due to the potential for forming brominated disinfection byproducts (DBPs) during drinking water treatment. Conventional treatment processes for bromide removal is costly and not specific. Selective bromide removal is technically challenging due to the presence of other ions in the brine, especially chloride as high as 30-200 g/L. This study evaluates the ability of solid graphite electrodes to selectively oxidize bromide to bromine in flowback water and produced water from a shale gas operation in Southwestern PA. The bromine can then be outgassed from the solution and recovered, as a process well understood in the bromine industry. This study revealed that bromide may be selectively and rapidly removed from oil and gas brines (~10 h(-1) m(-2) for produced water and ~60 h(-1) m(-2) for flowback water). The electrolysis occurs with a current efficiency between 60 and 90%, and the estimated energy cost is ~6 kJ/g Br. These data are similar to those for the chlor-alkali process that is commonly used for chlorine gas and sodium hydroxide production. The results demonstrate that bromide may be selectively removed from oil and gas brines to create an opportunity for environmental protection and resource recovery.

  2. Gas content of Gladys McCall reservoir brine

    Energy Technology Data Exchange (ETDEWEB)

    Hayden, C.G.; Randolph, P.L.

    1987-05-29

    On October 8, 1983, after the first full day of production from Sand No.8 in the Gladys McCall well, samples of separator gas and separator brine were collected for laboratory P-V-T (pressure, volume, temperature) studies. Recombination of amounts of these samples based upon measured rates at the time of sample collection, and at reservoir temperature (290 F), revealed a bubble point pressure of 9200 psia. This is substantially below the reported reservoir pressure of 12,783 psia. The gas content of the recombined fluids was 30.19 SCF of dry gas/STB of brine. In contrast, laboratory studies indicate that 35.84 SCF of pure methane would dissolve in each STB of 95,000 mg/L sodium chloride brine. These results indicate that the reservoir brine was not saturated with natural gas. By early April, 1987, production of roughly 25 million barrels of brine had reduced calculated flowing bottomhole pressure to about 6600 psia at a brine rate of 22,000 STB/D. If the skin factor(s) were as high as 20, flowing pressure drop across the skin would still be only about 500 psi. Thus, some portion of the reservoir volume was believed to have been drawn down to below the bubble point deduced from the laboratory recombination of separator samples. When the pressure in a geopressured geothermal reservoir is reduced to below the bubble point pressure for solution gas, gas is exsolved from the brine flowing through the pores in the reservoir rock. This exsolved gas is trapped in the reservoir until the fractional gas saturation of pore volume becomes large enough for gas flow to commence through a continuous gas-filled channel. At the same time, the gas/brine ratio becomes smaller and the chemistry of the remaining solution gas changes for the brine from which gas is exsolved. A careful search was made for the changes in gas/brine ratio or solution gas chemistry that would accompany pressure dropping below the bubble point pressure. Changes of about the same magnitude as the scatter in

  3. Conceptual design of the Truscott brine lake solar-pond system, volume 1: Utility-independent scenario

    Science.gov (United States)

    1981-06-01

    A conceptual design was performed for a series of solar pond systems to provide pumping power for chloride control in the Red River Basin. In the chloride control project, briny waters are diverted so as not to pollute portable water. The diverted brine is stored in a dammed natural basin where, with the aid of natural evaporation, the brine is concentrated to the salinities required for the solar ponds. The brine is transferred to the ponds and injected at the proper levels to establish the gradients and storage layers. The solar ponds are to be located within the Truscott, Texas brine impoundment lake. Heat will be extracted from the ponds and used to drive organic Rankine-cycle turbine generators. The electricity produced will serve the pumping needs of the chloride control project, pump brine from the natural source to the evaporation ponds, pump concentrated brine from the evaporation ponds to the solar ponds, maintain the solar ponds, and supply all system parasitic loads. It was found that five solar ponds with eight organic Rankine-cycle turbine-generators would serve both the average and peaking power requirements of the pumping stations in the Truscott area as they come on-line.

  4. Brine Sampling and Evaluation Program, 1991 report

    Energy Technology Data Exchange (ETDEWEB)

    Deal, D.E.; Abitz, R.J.; Myers, J.; Martin, M.L.; Milligan, D.J.; Sobocinski, R.W.; Lipponer, P.P.J. [International Technology Corp., Albuquerque, NM (United States); Belski, D.S. [Westinghouse Electric Corp., Carlsbad, NM (United States). Waste Isolation Div.

    1993-09-01

    The data presented in this report are the result of Brine Sampling and Evaluation Program (BSEP) activities at the Waste Isolation Pilot Plan (WIPP) during 1991. These BSEP activities document and investigate the origins, hydraulic characteristics, extent, and composition of brine occurrences in the Permian Salado Formation and seepage of that brine into the excavations at the WIPP. When excavations began at the WIPP in 1982, small brine seepages (weeps) were observed on the walls. Brine studies began as part of the Site Validation Program and were formalized as a program in its own right in 1985. During nine years of observations (1982--1991), evidence has mounted that the amount of brine seeping into the WIPP excavations is limited, local, and only a small fraction of that required to produce hydrogen gas by corroding the metal in the waste drums and waste inventory. The data through 1990 is discussed in detail and summarized by Deal and others (1991). The data presented in this report describes progress made during the calendar year 1991 and focuses on four major areas: (1) quantification of the amount of brine seeping across vertical surfaces in the WIPP excavations (brine ``weeps); (2) monitoring of brine inflow, e.g., measuring brines recovered from holes drilled downward from the underground drifts (downholes), upward from the underground drifts (upholes), and from subhorizontal holes; (3) further characterization of brine geochemistry; and (4) preliminary quantification of the amount of brine that might be released by squeezing the underconsolidated clays present in the Salado Formation.

  5. 7 CFR 58.320 - Brine tanks.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Brine tanks. 58.320 Section 58.320 Agriculture....320 Brine tanks. Brine tanks used for the treating of parchment liners shall be constructed of... liners. The tank should also be provided with a satisfactory drainage outlet....

  6. Sensitivity of Some Explosive/Brine Mixtures

    Science.gov (United States)

    1980-08-01

    concentration in brine mixtures. 3 Friction test results of brine mixtures. 10 4 Thermal test results of brine mixtures. 11 Li 71 - INTRODUCTION A...also carried out on these impact insensitive mixtures. Of the seven mixtures only the 15% M28-Comp. B sample passed the thermal test , since smoking

  7. Film boiling of mercury droplets

    Science.gov (United States)

    Baumeister, K. J.; Schoessow, G. J.; Chmielewski, C. E.

    1975-01-01

    Vaporization times of mercury droplets in Leidenfrost film boiling on a flat horizontal plate are measured in an air atmosphere. Extreme care was used to prevent large amplitude droplet vibrations and surface wetting; therefore, these data can be compared to film boiling theory. For these data, diffusion from the upper surface of the drop is a dominant mode of mass transfer from the drop. A closed-form analytical film boiling theory is developed to account for the diffusive evaporation. Reasonable agreement between data and theory is seen.

  8. Enhanced heat transfer in confined pool boiling

    NARCIS (Netherlands)

    Rops, C.M.; Lindken, R.; Velthuis, J.F.M.; Westerweel, J.

    2009-01-01

    We report the results of an experimental investigation of the heat transfer during nucleate boiling on a spatially confined boiling surface. The heat flux as a function of the boiling surface temperature was measured in pool boiling pots with diameters ranging from 15 mm down to 4.5 mm. It was found

  9. High flux film and transition boiling

    Energy Technology Data Exchange (ETDEWEB)

    Witte, L.C.

    1990-01-01

    This report is a bench-scale experiment on transition boiling. The author gives a detailed description on experimental apparatus and conditions. The visual observed boiling phenomena; nucleate boiling and film boiling, and the effect of heat transfer are also elucidated. 10 refs., 11 figs., 1 tab.

  10. Film boiling on vertical surfaces.

    Science.gov (United States)

    Suryanarayana, N. V.; Merte, H., Jr.

    1972-01-01

    Film boiling of a saturated liquid on a vertical surface is analyzed to determine the local heat-transfer rates as a function of height and heater-surface superheat. Experiments show that the laminar-flow model is inadequate. A turbulent-vapor-flow model is used, and the influence of the interfacial oscillations is incorporated on a semiempirical basis. Measurements of local film boiling were obtained with a transient technique using saturated liquid nitrogen.

  11. Brine Sampling and Evaluation Program, 1990 report

    Energy Technology Data Exchange (ETDEWEB)

    Deal, D.E.; Abitz, R.J.; Myers, J.; Case, J.B.; Martin, M.L.; Roggenthen, W.M. [International Technology Corp., Albuquerque, NM (United States); Belski, D.S. [Westinghouse Electric Corp., Carlsbad, NM (United States). Waste Isolation Div.

    1991-08-01

    The data presented in this report are the result of Brine Sampling and Evaluation Program (BSEP) activities at the Waste Isolation Pilot Plant (WIPP) during 1990. When excavations began in 1982, small brine seepages (weeps) were observed on the walls. These brine occurrences were initially described as part of the Site Validation Program. Brine studies were formalized in 1985. The BSEP activities document and investigate the origins, hydraulic characteristics, extent, and composition of brine occurrences in the Permian Salado Formation and seepage of that brine into the excavations at the WIPP. The brine chemistry is important because it assists in understanding the origin of the brine and because it may affect possible chemical reactions in the buried waste after sealing the repository. The volume of brine and the hydrologic system that drives the brine seepage also need to be understood to assess the long-term performance of the repository. After more than eight years of observations (1982--1990), no credible evidence exists to indicate that enough naturally occurring brine will seep into the WIPP excavations to be of practical concern. The detailed observations and analyses summarized herein and in previous BSEP reports confirm the evidence apparent during casual visits to the underground workings -- that the excavations are remarkably dry.

  12. Application of a Re-Pd bimetallic catalyst for treatment of perchlorate in waste ion-exchange regenerant brine.

    Science.gov (United States)

    Liu, Jinyong; Choe, Jong Kwon; Sasnow, Zachary; Werth, Charles J; Strathmann, Timothy J

    2013-01-01

    Concentrated sodium chloride (NaCl) brines are often used to regenerate ion-exchange (IX) resins applied to treat drinking water sources contaminated with perchlorate (ClO(4)(-)), generating large volumes of contaminated waste brine. Chemical and biological processes for ClO(4)(-) reduction are often inhibited severely by high salt levels, making it difficult to recycle waste brines. Recent work demonstrated that novel rhenium-palladium bimetallic catalysts on activated carbon support (Re-Pd/C) can efficiently reduce ClO(4)(-) to chloride (Cl(-)) under acidic conditions, and here the applicability of the process for treating waste IX brines was examined. Experiments conducted in synthetic NaCl-only brine (6-12 wt%) showed higher Re-Pd/C catalyst activity than in comparable freshwater solutions, but the rate constant for ClO(4)(-) reduction measured in a real IX waste brine was found to be 65 times lower than in the synthetic NaCl brine. Through a series of experiments, co-contamination of the IX waste brine by excess NO(3)(-) (which the catalyst reduces principally to NH(4)(+)) was found to be the primary cause for deactivation of the Re-Pd/C catalyst, most likely by altering the immobilized Re component. Pre-treatment of NO(3)(-) using a different bimetallic catalyst (In-Pd/Al(2)O(3)) improved selectivity for N(2) over NH(4)(+) and enabled facile ClO(4)(-) reduction by the Re-Pd/C catalyst. Thus, sequential catalytic treatment may be a promising strategy for enabling reuse of waste IX brine containing NO(3)(-) and ClO(4)(-).

  13. Distillation Brine Purification for Resource Recovery Applications

    Science.gov (United States)

    Wheeler, Raymond M.

    2014-01-01

    Wastewater processing systems for space generate residual brine that contains water and salts that could be recovered to life support consumables. The project assessed the use of ion-exchange resins to selectively remove salts from wastewater treatment brines. The resins were then regenerated for additional use. The intention would be to generate a Na/K and CI rich or purified brine that would then be processed into high value chemicals, such as acids, bases, and/or bleach.

  14. Design of the Brine Evaporation Bag for Increased Water Recovery in Microgravity

    Science.gov (United States)

    Hayden, Anna L.; Delzeit, Lance D.

    2015-01-01

    The existing water recovery system on the International Space Station (ISS) is limited to 75% reclamation; consequently, long duration space missions are currently unfeasible due to the large quantity of water necessary to sustain the crew. The Brine Evaporation Bag (BEB) is a proposed system to supplement the existing water recovery system aboard the ISS that can to increase water recovery to 99%. The largest barrier to high water recovery is mineral scaling inside the water recovery equipment, which leads to equipment failure; therefore, some water must remain to keep the minerals dissolved. This waste stream is liquid brine containing salts, acids, organics, and water. The BEB is designed to recover this remaining water while protecting the equipment from scale. The BEB consists of a sealed bag containing a hydrophobic membrane that allows water vapor and gas to pass through. It is operated under vacuum, heated, and continuously filled with brine to boil away the water. The water vapor is recovered and the solids are contained inside the bag for disposal. The BEB can dry the brine to a solid block. Ongoing work includes improving the design of the BEB and the evaporator to prevent leaks, maximize the rate of water removal, and minimize energy use and weight. Additional testing will determine whether designs are heat- or mass-transfer limited and the optimal water recovery rate.

  15. Brine disposal process for Morcinek coal mine

    Energy Technology Data Exchange (ETDEWEB)

    Tait, J.H. [Aquatech Services, Inc., Citrus Heights, CA (United States)

    1995-04-01

    This paper describes the work to develop a commercial brine disposal process for the Morcinek mine, located 45 km south of the city of Katowice in Poland. Currently, brine is discharged into the Odra river and methane from the mine is released into the atmosphere. The process would use the released methane and convert a large percentage of the brine into potable water for commercial use. Thus, the proposed process has two environmental benefits. The brine salinity is about 31,100 ppm. Major brine components are Na (10,300 ppm), Ca (1,170 ppm), Mg (460 ppm), Cl (18,500 ppm) and SO{sub 4}{sup 2-} (252 ppm). Present in smaller amounts are K, S, Sr, B, Ba and NO{sub 3}. The process integrates a reverse osmosis (RO) unit and a submerged combustion evaporator. Extensive studies made at the Lawrence Livermore National Laboratory established the pretreatment method of the brine before it enters the RO unit. Without adequate pretreatment, mineral phases in the brine would become super-saturated and would precipitate in the RO unit. The pretreatment consists of first adding sodium carbonate to increase both the pH and the carbonate concentration of the brine. This addition causes precipitation of carbonate solids containing Ca, Mg, Sr, and Ba. After filtration of these precipitates, the fluid is acidified with HCl to prevent precipitation in the RO unit as the brine increases in salinity.

  16. On the physico-chemical characteristics of brines

    Digital Repository Service at National Institute of Oceanography (India)

    Shirodkar, P.V.; Rao, P.V.S.S.D.P.; Singbal, S.Y.S.

    Analyses of the natural brines form the salt lakes, salt pans and the artificial brines obtained after the solar desalination of seawater respectively, showed wide differences in their physico-chemical characteristics. The natural brines are markEd...

  17. The Brine Shrimp's Butterfly Stroke

    CERN Document Server

    Johnson, Brennan; Dasi, Lakshmi Prasad

    2011-01-01

    We investigate the fluid dynamics of brine shrimp larvae swimming in this gallery of fluid motion video. Time resolved particle image velocimetry was performed using nano-particles as seeding material to measure the time dependent velocity and vorticity fields. The Reynolds number of the flow was roughly 8 and the Womerseley number (ratio of periodic forcing to viscous forcing) was about 5. Vorticity dynamics reveals the formation of a vortex ring structure at the tip of each arm at the beginning of the power stroke. This two vortex system evolves dramatically with time as the stroke progresses. The outer circulation is noted to weaken while the inner circulation strengthens over the power stroke. The gaining strength of the inner vortex correlates with the acceleration and forward movement of the larvae.

  18. Study of brine treatment. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1977-11-01

    Available information pertinent to the treatment of geothermal brines was collected by literature search and then evaluated and summarized for use by the electric utility and geothermal industries. The information was screened from the geothermal, oil and gas, wastewater disposal, and boiler water treatment industries. The current state of knowledge and methodology concerning the treatment of geothermal brines to control scaling and corrosion in geothermal electric power production was assessed. Currently, geothermal scale in pipes and wells is removed by physical or chemical methods. There is a growing effort on developing methods to control scale formation for both fresh and spent brines, including pH adjustment and application of an electrical potential for fresh fluids, and coagulation to treat spent fluids. Current methods of corrosion control center around planned replacement of piping and other plant components, with efforts focused primarily on development of materials with improved corrosion resistance. Recommendations for additional work to improve brine treatment include the following: (1) chemical and physical characterization of brine and scale compositions, (2) basic data on the mechanism of scale formation and the effects of inhibitors, (3) development of instrumentation to monitor geothermal brine constituents, (4) correlation of laboratory results with field test data, and (5) screening of currently available commercial inhibitors for application to geothermal brines. An annotated bibliography of the reference material used in this study is included.

  19. Lithium brines: A global perspective: Chapter 14

    Science.gov (United States)

    Munk, LeeAnn; Hynek, Scott; Bradley, Dwight C.; Boutt, David; Labay, Keith A.; Jochens, Hillary; Verplanck, Philip L.; Hitzman, Murray W.

    2016-01-01

    Lithium is a critical and technologically important element that has widespread use, particularly in batteries for hybrid cars and portable electronic devices. Global demand for lithium has been on the rise since the mid-1900s and is projected to continue to increase. Lithium is found in three main deposit types: (1) pegmatites, (2) continental brines, and (3) hydrothermally altered clays. Continental brines provide approximately three-fourths of the world’s Li production due to their relatively low production cost. The Li-rich brine systems addressed here share six common characteristics that provide clues to deposit genesis while also serving as exploration guidelines. These are as follows: (1) arid climate; (2) closed basin containing a salar (salt crust), a salt lake, or both; (3) associated igneous and/or geothermal activity; (4) tectonically driven subsidence; (5) suitable lithium sources; and (6) sufficient time to concentrate brine. Two detailed case studies of Li-rich brines are presented; one on the longest produced lithium brine at Clayton Valley, Nevada, and the other on the world’s largest producing lithium brine at the Salar de Atacama, Chile.

  20. Brine Organisms and the Question of Habitat Specific Adaptation

    Science.gov (United States)

    Siegel, B. Z.; Siegel, S. M.; Speitel, Thomas; Waber, Jack; Stoecker, Roy

    1984-12-01

    Among the well-known ultrasaline terrestrial habitats, the Dead Sea in the Jordan Rift Valley and Don Juan Pond in the Upper Wright Valley represent two of the most extreme. The former is a saturated sodium chloride-magnesium sulfate brine in a hot desert, the latter a saturated calcium chloride brine in an Antarctic desert. Both Dead Sea and Don Juan water bodies themselves are limited in microflora, but the saline Don Juan algal mat and muds contain abundant nutrients and a rich and varied microbiota, including Oscillatoria, Gleocapsa, Chlorella, diatoms, Penicillium and bacteria. In such environments, the existence of an array of specific adaptations is a common, and highly reasonable, presumption, at least with respect to habitat-obligate forms. Nevertheless, many years of ongoing study in our laboratory have demonstrated that lichens (e.g. Cladonia), algae (e.g. Nostoc) and fungi (e.g. Penicillium, Aspergillus) from the humid tropics can sustain metabolism down to -40°C and growth down to -10°C in simulated Dead Sea or Don Juan (or similar) media without benefit of selection or gradual acclimation. Non-selection is suggested in fungi by higher growth rates from vegetative inocula than spores. The importance of nutrient parameters was also evident in responses to potassium and reduced nitrogen compounds. In view of the saline performance of tropical Nostoc, and its presence in the Antarctic dry valley soils, its complete absence in our Don Juan mat samples was and remains a puzzle. We suggest that adaptive capability is already resident in many terrestrial life forms not currently in extreme habitats, a possible reflection of evolutionary selection for wide spectrum environmental adaptability.

  1. Zooplankton at deep Red Sea brine pools

    KAUST Repository

    Kaartvedt, Stein

    2016-03-02

    The deep-sea anoxic brines of the Red Sea comprise unique, complex and extreme habitats. These environments are too harsh for metazoans, while the brine–seawater interface harbors dense microbial populations. We investigated the adjacent pelagic fauna at two brine pools using net tows, video records from a remotely operated vehicle and submerged echosounders. Waters just above the brine pool of Atlantis II Deep (2000 m depth) appeared depleted of macrofauna. In contrast, the fauna appeared to be enriched at the Kebrit Deep brine–seawater interface (1466 m).

  2. Coiled Brine Recovery Assembly (CoBRA): A New Approach to Recovering Water from Wastewater Brines

    Science.gov (United States)

    Pensinger, Stuart J.

    2015-01-01

    Brine water recovery represents a current technology gap in water recycling for human spaceflight. The role of a brine processor is to take the concentrated discharge from a primary wastewater processor, called brine, and recover most of the remaining water from it. The current state-of-the-art primary processor is the ISS Urine Processor Assembly (UPA) that currently achieves 70% water recovery. Recent advancements in chemical pretreatments are expected to increase this to 85% in the near future. This is a welcome improvement, yet is still not high enough for deep space transit. Mission architecture studies indicate that at least 95% is necessary for a Mars mission, as an example. Brine water recovery is the technology that bridges the gap between 85% and 95%, and moves life support systems one step closer to full closure of the water loop. Several brine water recovery systems have been proposed for human spaceflight, most of them focused on solving two major problems: operation in a weightless environment, and management and containment of brine residual. Brine residual is the leftover byproduct of the brine recovery process, and is often a viscous, sticky paste, laden with crystallized solid particles. Due to the chemical pretreatments added to wastewater prior to distillation in a primary processor, these residuals are typically toxic, which further complicates matters. Isolation of crewmembers from these hazardous materials is paramount. The Coiled Brine Recovery Assembly (CoBRA) is a recently developed concept from the Johnson Space Center that offers solutions to these challenges. CoBRA is centered on a softgoods evaporator that enables a passive fill with brine, and regeneration by discharging liquid brine residual to a collection bag. This evaporator is meant to be lightweight, which allows it to be discarded along with the accumulated brine solids contained within it. This paper discusses design and development of a first CoBRA prototype, and reports

  3. Brine Dewatering Using Ultrasonic Nebulization Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Recovery of water from brine is critically important for future manned space exploration. Resupply of water is prohibitively costly for such extended missions. Water...

  4. Brine Dewatering Using Ultrasonic Nebulization Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Recovery of water from brine is critically important for manned space exploration. Resupply of water is prohibitively costly for extended missions. It is anticipated...

  5. Instability in flow boiling in microchannels

    CERN Document Server

    Saha, Sujoy Kumar

    2016-01-01

    This Brief addresses the phenomena of instability in flow boiling in microchannels occurring in high heat flux electronic cooling. A companion edition in the SpringerBrief Subseries on Thermal Engineering and Applied Science to “Critical Heat Flux in Flow Boiling in Microchannels,” and "Heat Transfer and Pressure Drop in Flow Boiling in Microchannels,"by the same author team, this volume is idea for professionals, researchers, and graduate students concerned with electronic cooling.

  6. Gamma heated subassembly for sodium boiling experiments

    Energy Technology Data Exchange (ETDEWEB)

    Artus, S.C.

    1975-01-01

    The design of a system to boil sodium in an LMFBR is examined. This design should be regarded as a first step in a series of boiling experiments. The reactor chosen for the design of the boiling apparatus is the Experimental Breeder Reactor-II (EBR-II), located at the National Reactor Testing Station in Idaho. Criteria broadly classified as design objectives and design requirements are discussed.

  7. Space and Industrial Brine Drying Technologies

    Science.gov (United States)

    Jones, Harry W.; Wisniewski, Richard S.; Flynn, Michael; Shaw, Hali

    2014-01-01

    This survey describes brine drying technologies that have been developed for use in space and industry. NASA has long considered developing a brine drying system for the International Space Station (ISS). Possible processes include conduction drying in many forms, spray drying, distillation, freezing and freeze drying, membrane filtration, and electrical processes. Commercial processes use similar technologies. Some proposed space systems combine several approaches. The current most promising candidates for use on the ISS use either conduction drying with membrane filtration or spray drying.

  8. Pool Boiling of Hydrocarbon Mixtures on Water

    Energy Technology Data Exchange (ETDEWEB)

    Boee, R.

    1996-09-01

    In maritime transport of liquefied natural gas (LNG) there is a risk of spilling cryogenic liquid onto water. The present doctoral thesis discusses transient boiling experiments in which liquid hydrocarbons were poured onto water and left to boil off. Composition changes during boiling are believed to be connected with the initiation of rapid phase transition in LNG spilled on water. 64 experimental runs were carried out, 14 using pure liquid methane, 36 using methane-ethane, and 14 using methane-propane binary mixtures of different composition. The water surface was open to the atmosphere and covered an area of 200 cm{sup 2} at 25 - 40{sup o}C. The heat flux was obtained by monitoring the change of mass vs time. The void fraction in the boiling layer was measured with a gamma densitometer, and a method for adapting this measurement concept to the case of a boiling cryogenic liquid mixture is suggested. Significant differences in the boil-off characteristics between pure methane and binary mixtures revealed by previous studies are confirmed. Pure methane is in film boiling, whereas the mixtures appear to enter the transitional boiling regime with only small amounts of the second component added. The results indicate that the common assumption that LNG will be in film boiling on water because of the high temperature difference, may be questioned. Comparison with previous work shows that at this small scale the results are influenced by the experimental apparatus and procedures. 66 refs., 76 figs., 28 tabs.

  9. Duality of boiling systems and uncertainty phenomena

    Institute of Scientific and Technical Information of China (English)

    柴立合; 彭晓峰; 王补宣

    2000-01-01

    Interactions among dry patches at high heat flux are theoretically analyzed. The high heat flux boiling experiments on metal plate wall with different materials and thickness are correspondingly conducted. The duality of boiling system, i.e. hydrodynamic performance and self-organized performance is identified. A unified explanation of hydrodynamic models and dry patches models is given. The scatter and uncertainty in boiling data can be mainly attributed to the intrinsic duality, but not the sole surface effects. The present experimental results explain why the deviation point at high flux boiling is seen only on occasion and why the self-organization of dry patches is often ignored in available literature.

  10. Boiling flow through diverging microchannel

    Indian Academy of Sciences (India)

    V S Duryodhan; S G Singh; Amit Agrawal

    2013-12-01

    An experimental study of flow boiling through diverging microchannel has been carried out in this work, with the aim of understanding boiling in nonuniform cross-section microchannel. Diverging microchannel of 4° of divergence angle and 146 m hydraulic diameter (calculated at mid-length) has been employed for the present study with deionised water as working fluid. Effect of mass flux (118–1182 kg/m2-s) and heat flux (1.6–19.2 W/cm2) on single and two-phase pressure drop and average heat transfer coefficient has been studied. Concurrently, flow visualization is carried out to document the various flow regimes and to correlate the pressure drop and average heat transfer coefficient to the underlying flow regime. Four flow regimes have been identified from the measurements: bubbly, slug, slug–annular and periodic dry-out/rewetting. Variation of pressure drop with heat flux shows one maxima which corresponds to transition from bubbly to slug flow. It is shown that significantly large heat transfer coefficient (up to 107 kW/m2-K) can be attained for such systems, for small pressure drop penalty and with good flow stability.

  11. ANODIC BEHAVIOR OF ALLOY 22 IN HIGH NITRATE BRINES AT TEMPERATURES HIGHER THAN 100C

    Energy Technology Data Exchange (ETDEWEB)

    G.O. LLEVBARE; J.C. ESTILL; A. YILMAZ; R.A. ETIEN; G.A. HUST M.L. STUART

    2006-04-20

    Alloy 22 (N06022) may be susceptible to crevice corrosion in chloride solutions. Nitrate acts as an inhibitor to crevice corrosion. Several papers have been published regarding the effect of nitrate on the corrosion resistance of Alloy 22 at temperatures 100 C and lower. However, very little is known about the behavior of this alloy in highly concentrated brines at temperatures above 100 C. In the current work, electrochemical tests have been carried out to explore the anodic behavior of Alloy 22 in high chloride high nitrate electrolytes at temperatures as high as 160 C at ambient atmospheres. Even though Alloy 22 may adopt corrosion potentials in the order of +0.5 V (in the saturated silver chloride scale), it does not suffer crevice corrosion if there is high nitrate in the solution. That is, the inhibitive effect of nitrate on crevice corrosion is active for temperatures higher than 100 C.

  12. Study and testing of direct contact heat exchangers for geothermal brines. Final report, June 1975--July 1976

    Energy Technology Data Exchange (ETDEWEB)

    Suratt, W.B.; Hart, G.K.

    1977-01-01

    The object of the work reported herein was to assess the technical and economic feasibility of preheating and evaporating a secondary fluid via direct contact with hot geothermal brine. The work covered a period of 12 months and included the design, construction, and testing of a unit which heats and vaporizes 10 gpm of isobutane by direct contact with 325/sup 0/F brine. The analytical and experimental efforts explored design and economic characteristics, including anticipated problem areas such as working fluid loss in the brine, production of a stable dispersion of the working fluid in brine, fluids separation, axial mixing and carry-over of water vapor with the working fluid. Isobutane was selected as the working fluid for tests primarily because of the favorable amount of net work produced per pound of geothermal brine and the low amount and cost of working fluid lost in the heat exchange process. The Elgin Spray Tower concept was selected for the preheater and boiler. The test apparatus includes a separate boiler and a separate preheater, each 6'' diameter by 6' high. Brine enters the top of each vessel and leaves the bottom. Isobutane enters the bottom of the preheater through a distributor plate to produce 0.15 inch diameter drops. The experimental unit operated with no major problems and demonstrated its hydraulic and thermal capabilities. Volumetric heat transfer coefficients obtained ranged up to 4000 BTU/hr /sup 0/F ft/sup 3/. Boiling heat transfer coefficients of as high as 17,000 BTU/hr /sup 0/F ft/sup 3/ were obtained with a design value of 10,000 BTU/hr /sup 0/F ft/sup 3/. Amount of isobutane in a 21 percent NaCl solution leaving the preheater was less than 40 ppM. A conceptual design and cost estimate was prepared for a direct contact heat exchange system sized for a 50 MW power plant.

  13. Transient boiling crisis of cryogenic liquids

    NARCIS (Netherlands)

    Deev, [No Value; Kharitonov, VS; Kutsenko, KV; Lavrukhin, AA

    2004-01-01

    This paper introduces a new physical model of boiling crisis under rapid increase of power on the heated surface. The calculation of the time interval of the transition to film boiling in cryogenic liquids was carried out depending on heat flux and pressure. The obtained results are in good agreemen

  14. Boiling turbulent Rayleigh-Bénard convection

    NARCIS (Netherlands)

    Lakkaraju, R.

    2013-01-01

    A fundamental understanding of liquid-vapor phase transitions, mainly boiling phenomenon, is essential due to its omnipresence in science and technology. In industries, many empirical correlations exist on the heat transport to get an optimized and efficient thermal design of the boiling equipment.

  15. Chloride transference during electrochemical chloride extraction process

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Chemical titration method and lab-made chloride probes were jointly adopted to investigate the effects of water-to-cement (W/C) ratio and the impressed current density on chloride transport for cement-based materials during electrochemical chloride extraction (ECE) process.The dissolution of bound chlorides and the effect of current density on dissolution were analyzed.The variations of chloride concentration at different depths and the chloride transference process were monitored.Test results show that W/C ratios adopted have slight influence on chloride extraction,while chloride extraction efficiency is mainly determined by the impressed current density.During ECE process a portion of bound chloride ions dissolved and the amount of bound chlorides released is directly proportional to current density.

  16. A Novel Ion Exchange System to Purify Mixed ISS Waste Water Brines for Chemical Production and Enhanced Water Recovery

    Science.gov (United States)

    Lunn, Griffin; Spencer, LaShelle; Ruby, Anna-Maria; McCaskill, Andrew

    2014-01-01

    Current International Space Station water recovery regimes produce a sizable portion of waste water brine. This brine is highly toxic and water recovery is poor: a highly wasteful proposition. With new biological techniques that do not require waste water chemical pretreatment, the resulting brine would be chromium-free and nitrate rich which can allow possible fertilizer recovery for future plant systems. Using a system of ion exchange resins we can remove hardness, sulfate, phosphate and nitrate from these brines to leave only sodium and potassium chloride. At this point modern chlor-alkali cells can be utilized to produce a low salt stream as well as an acid and base stream. The first stream can be used to gain higher water recovery through recycle to the water separation stage while the last two streams can be used to regenerate the ion exchange beds used here, as well as other ion exchange beds in the ISS. Conveniently these waste products from ion exchange regeneration would be suitable as plant fertilizer. In this report we go over the performance of state of the art resins designed for high selectivity of target ions under brine conditions. Using ersatz ISS waste water we can evaluate the performance of specific resins and calculate mass balances to determine resin effectiveness and process viability. If this system is feasible then we will be one step closer to closed loop environmental control and life support systems (ECLSS) for current or future applications.

  17. Advanced oxidation of iodinated X-ray contrast media in reverse osmosis brines: the influence of quenching.

    Science.gov (United States)

    Azerrad, Sara P; Gur-Reznik, Shirra; Heller-Grossman, Lilly; Dosoretz, Carlos G

    2014-10-01

    Among the main restrictions for the implementation of advanced oxidation processes (AOPs) for removal of micropollutants present in reverse osmosis (RO) brines of secondary effluents account the quenching performed by background organic and inorganic constituents. Natural organic matter (NOM) and soluble microbial products (SMP) are the main effluent organic matter constituents. The inorganic fraction is largely constituted by chlorides and bicarbonate alkalinity with sodium and calcium as main counterions. The quenching influence of these components, separately and their mixture, in the transformation of model compounds by UVA/TiO2 was studied applying synthetic brines solutions mimicking 2-fold concentrated RO secondary effluents brines. The results were validated using fresh RO brines. Diatrizoate (DTZ) and iopromide (IOPr) were used as model compound. They have been found to exhibit relative high resistance to oxidation process and therefore represent good markers for AOPs techniques. Under the conditions applied, oxidization of DTZ in the background of RO brines was strongly affected by quenching effects. The major contribution to quenching resulted from organic matter (≈70%) followed by bicarbonate alkalinity (≈30%). NOM displayed higher quenching than SMP in spite of its relative lower concentration. Multivalent cations, i.e., Ca(+2), were found to decrease effectiveness of the technique due to agglomeration of the catalyst. However this influence was lowered in presence of NOM. Different patterns of transformation were found for each model compound in which a delayed deiodination was observed for iopromide whereas diatrizoate oxidation paralleled deiodination.

  18. Brine flow in heated geologic salt.

    Energy Technology Data Exchange (ETDEWEB)

    Kuhlman, Kristopher L.; Malama, Bwalya

    2013-03-01

    This report is a summary of the physical processes, primary governing equations, solution approaches, and historic testing related to brine migration in geologic salt. Although most information presented in this report is not new, we synthesize a large amount of material scattered across dozens of laboratory reports, journal papers, conference proceedings, and textbooks. We present a mathematical description of the governing brine flow mechanisms in geologic salt. We outline the general coupled thermal, multi-phase hydrologic, and mechanical processes. We derive these processes governing equations, which can be used to predict brine flow. These equations are valid under a wide variety of conditions applicable to radioactive waste disposal in rooms and boreholes excavated into geologic salt.

  19. Boiling Heat Transfer to Halogenated Hydrocarbon Refrigerants

    Science.gov (United States)

    Yoshida, Suguru; Fujita, Yasunobu

    The current state of knowledge on heat transfer to boiling refrigerants (halogenated hydrocarbons) in a pool and flowing inside a horizontal tube is reviewed with an emphasis on information relevant to the design of refrigerant evaporators, and some recommendations are made for future research. The review covers two-phase flow pattern, heat transfer characteristics, correlation of heat transfer coefficient, influence of oil, heat transfer augmentation, boiling from tube-bundle, influence of return bend, burnout heat flux, film boiling, dryout and post-dryout heat transfer.

  20. Tribenzylammonium chloride

    Directory of Open Access Journals (Sweden)

    Waly Diallo

    2014-05-01

    Full Text Available Single crystals of the title salt, C21H21NH+·Cl−, were isolated as a side product from the reaction involving [(C6H5CH23NH]2[HPO4] and Sn(CH33Cl in ethanol. Both the cation and the anion are situated on a threefold rotation axis. The central N atom in the cation has a slightly distorted tetrahedral environment, with angles ranging from 107.7 to 111.16 (10°. In the crystal, the tribenzylammonium cations and chloride anions are linked through N—H...Cl and C—H...Cl hydrogen bonds, leading to the formation of infinite chains along [001]. The crystal studied was a merohedral twin.

  1. Microlayer during boiling in narrow slot channels

    Science.gov (United States)

    Diev, Mikhail D.; Leontiev, Alexander I.

    1997-01-01

    An international space station Alpha will have a two-phase thermal control system. Boiling of a liquid ammonia will be a process of heat collection in evaporative heat exchangers. Unfortunately, only little data is available for boiling heat transfer in microgravity. Geometries of boiling channels working good in normal gravity are not appropriate in microgravity, and special means should be worked out to avoid some undesired events. From this point of view, the narrow slot channels may be assumed as a promising geometry for microgravity operation. During boiling in narrow slots, the vapor bubbles are flattened between the channel walls. The vapor phase and the channel wall are separated by a thin liquid film which is known as a microlayer. The paper presents the experimental results compared to the theoretical analysis, the paper also shows the narrow slot channels as a perspective configuration for microgravity applications.

  2. Ice Control with Brine on Highways

    DEFF Research Database (Denmark)

    Bolet, Lars

    During the years 1996-2006, the Division of Highways and Transportation in the former county of Funen gradually replaced pre-wetted salt with brine as de-icing agent in all her ice control activities. The replacement related to 1000 kilometres of highways. Jeopardizing neither road safety nor...

  3. Rheological Properties of Silica Nanoparticles in Brine and Brine-Surfactant Systems

    Science.gov (United States)

    Pales, Ashley; Kinsey, Erin; Li, Chunyan; Mu, Linlin; Bai, Lingyun; Clifford, Heather; Darnault, Christophe

    2016-04-01

    Rheological Properties of Silica Nanoparticles in Brine and Brine-Surfactant Systems Ashley R. Pales, Erin Kinsey, Chunyan Li, Linlin Mu, Lingyun Bai, Heather Clifford, and Christophe J. G. Darnault Department of Environmental Engineering and Earth Sciences, Laboratory of Hydrogeoscience and Biological Engineering, L.G. Rich Environmental Laboratory, Clemson University, Clemson, SC, USA Nanofluids are suspensions of nanometer sized particles in any fluid base, where the nanoparticles effect the properties of the fluid base. Commonly, nanofluids are water based, however, other bases such as ethylene-glycol, glycerol, and propylene-glycol, have been researched to understand the rheological properties of the nanofluids. This work aims to understand the fundamental rheological properties of silica nanoparticles in brine based and brine-surfactant based nanofluids with temperature variations. This was done by using variable weight percent of silica nanoparticles from 0.001% to 0.1%. Five percent brine was used to create the brine based nanofluids; and 5% brine with 2CMC of Tween 20 nonionic surfactant (Sigma-Aldrich) was used to create the brine-surfactant nanofluid. Rheological behaviors, such as shear rate, shear stress, and viscosity, were compared between these nanofluids at 20C and at 60C across the varied nanoparticle wt%. The goal of this work is to provide a fundamental basis for future applied testing for enhanced oil recovery. It is hypothesized that the addition of surfactant will have a positive impact on nanofluid properties that will be useful for enhance oil recovery. Differences have been observed in preliminary data analysis of the rheological properties between these two nanofluids indicating that the surfactant is having the hypothesized effect.

  4. The investigation of boiling crisis of nanofluids

    Directory of Open Access Journals (Sweden)

    Minakov Andrey

    2016-01-01

    Full Text Available Saturated boiling of nanofluids on a cylindrical heater with different diameters is experimentally studied. Studied nanofluids were prepared using distilled water and different metal oxides nanoparticles. The volume concentration of the nanoparticles was changed from 0.05 to 1%. It has been measured that the critical heat flux for nanofluids was much higher than for water. A strong dependence of CHF on the material and size of the nanoparticles and duration of boiling and size of heater was shown.

  5. Using Boiling for Treating Waste Activated Sludge

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In this work we investigated the feasibility of using short time, low superheat boiling to treat biological sludge. The treated sludge exhibited reduced filterability and enhanced settleability. The boiling treatment released a large amount of extra-cellular polymers (ECPs) from the solid phase and reduced the microbial density levels of the total coliform bacteria and the heterotrophic bacteria. A diluted sludge is preferable for its high degree of organic hydrolysis and sufficient reduction in microbial density levels.

  6. How To Boil the Perfect Egg

    Institute of Scientific and Technical Information of China (English)

    小雨

    2007-01-01

    A British inventor says he has cracked(破解)the age-old riddle(难题)of how to boil the perfect egg,get rid of(摆脱)the water. Simon Rhymes uses powerful light bulbs instead of boiling water to cook the egg. The gadget(小发明)does the job in six minutes,and then chons off(削)the top of

  7. Mirabilite solubility in equilibrium sea ice brines

    Science.gov (United States)

    Butler, Benjamin Miles; Papadimitriou, Stathys; Santoro, Anna; Kennedy, Hilary

    2016-06-01

    The sea ice microstructure is permeated by brine channels and pockets that contain concentrated seawater-derived brine. Cooling the sea ice results in further formation of pure ice within these pockets as thermal equilibrium is attained, resulting in a smaller volume of increasingly concentrated residual brine. The coupled changes in temperature and ionic composition result in supersaturation of the brine with respect to mirabilite (Na2SO4·10H2O) at temperatures below -6.38 °C, which consequently precipitates within the sea ice microstructure. Here, mirabilite solubility in natural and synthetic seawater derived brines, representative of sea ice at thermal equilibrium, has been measured in laboratory experiments between 0.2 and -20.6 °C, and hence we present a detailed examination of mirabilite dynamics within the sea ice system. Below -6.38 °C mirabilite displays particularly large changes in solubility as the temperature decreases, and by -20.6 °C its precipitation results in 12.90% and 91.97% reductions in the total dissolved Na+ and SO42- concentrations respectively, compared to that of conservative seawater concentration. Such large non-conservative changes in brine composition could potentially impact upon the measurement of sea ice brine salinity and pH, whilst the altered osmotic conditions may create additional challenges for the sympagic organisms that inhabit the sea ice system. At temperatures above -6.38 °C, mirabilite again displays large changes in solubility that likely aid in impeding its identification in field samples of sea ice. Our solubility measurements display excellent agreement with that of the FREZCHEM model, which was therefore used to supplement our measurements to colder temperatures. Measured and modelled solubility data were incorporated into a 1D model for the growth of first-year Arctic sea ice. Model results ultimately suggest that mirabilite has a near ubiquitous presence in much of the sea ice on Earth, and illustrate the

  8. High flux film and transition boiling

    Science.gov (United States)

    Witte, L. C.

    1993-02-01

    An investigation was conducted on the potential for altering the boiling curve through effects of high velocity and high subcooling. Experiments using water and Freon-113 flowing over cylindrical electrical heaters in crossflow were made to see how velocity and subcooling affect the boiling curve, especially the film and transition boiling regions. We sought subcooling levels down to near the freezing points of these two liquids to prove the concept that the critical heat flux and the minimum heat flux could be brought together, thereby averting the transition region altogether. Another emphasis was to gain insight into how the various boiling regions could be represented mathematically on various parts of the heating surface. Motivation for the research grew out of a realization that the effects of very high subcooling and velocity might be to avert the transition boiling altogether so that the unstable part of the boiling curve would not limit the application of high flux devices to temperatures less than the burnout temperatures. Summaries of results from the study are described. It shows that the potential for averting the transition region is good and points the way to further research that is needed to demonstrate the potential.

  9. Experimental confirmation of liquid brines on Mars

    Science.gov (United States)

    Fischer, E.; Renno, N. O.; Martinez, G.

    2015-12-01

    The discovery of water ice and perchlorates in the shallow subsurface of Mars [1,2] is interesting because they could produce aqueous liquid solutions under Mars' present-day environmental conditions. We used the Michigan Mars Environmental Chamber [3] to simulate the pressure, temperature and relative humidity during the full diurnal cycle of sol 19 at the Phoenix landing site. Sol 19 was chosen because on this sol ice found in a shallow trench (Dodo-Goldilocks) at a depth of ~5 cm was removed with little effort [4], suggesting that it was a frozen brine (softer than freshwater ice), and because oblate spheroids found on a strut of the lander, possibly a saline mud, were observed to grow and darken (suggesting liquefaction) [4]. The results of our simulations show that early in the mission the frozen brine likely found in the Dodo-Goldilocks trench could melt in the morning, temporarily forming aqueous liquid solutions when the temperature in the trench was above the eutectic temperature of the Ca(ClO4)2 salt (~199 K). In addition, the results of our simulations indicate that the spheroids observed on a strut of the Phoenix lander were most likely droplets of liquid brines. Since halophilic terrestrial bacteria thrive in brines [5], our results suggest that Mars' polar region could potentially be a habitat for microorganisms. In addition, it has been suggested that frost could form on fine-grained terrains at Gale crater during the winter [6]. If this frost gets in contact with perchlorate salts, it could melt temporarily forming liquid brines.

  10. Flow boiling heat transfer in circulating fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Xiaoguang REN; Jiangdong ZHENG; Sefiane KHELLII; Arumemi-Ikhide MICHAEL

    2009-01-01

    In order to enhance heat transfer and mitigate contamination in the boiling processes, a new type of vapor-liquid-solid (3-phase) circulating fluidized bed boil-ing system has been designed, combining a circulating fluidized bed with boiling heat transfer. Experimental results show an enhancement of the boiling curve. Flow visualization studies concerning flow hydrodynamics within the riser column are also conducted whose results are presented and discussed.

  11. Brine treatment test for reinjection on Cerro Prieto geothermal field

    Energy Technology Data Exchange (ETDEWEB)

    Hurtado, R.; Mercado, S.; Gamino, H. (Departamento de Geotermia, Division de Fuentes de Energia, Instituto de Investigaciones Electricas, Justo Sierra y Herreros Sur 2098-Altos C.P. 21020, Mexicali, B.C. (MX))

    1989-01-01

    Reinjection of disposal brine from the Cerro Prieto Geothermal Power Plant System is attractive mainly because, on top of solving the brine disposal problem, it may significantly contribute to extend the reservoir useful lifetime, through thermal and hydraulic recharge. Because the high concentration of colloidal silica in the disposal brine, laboratory and pilot plant tests were conducted in order to develop the brine treatment process. Addition of 20-40 mg/1 lime to flashed and aged brine for 10-20 minutes yields a clarified brine relatively low in suspended solids (10-30 mg/1) when the over flow rate is 38.5 1/min-m/sup 2/. 1.1 mills/kWh was the estimated cost for treatment of 800 kg/s of separated brine from the Cerro Prieto I power station.

  12. Geochemistry of Brines from Salt Ore Deposits in Western Tarim Basin

    Institute of Scientific and Technical Information of China (English)

    马万栋; 马海州; 谭红兵; 董亚萍; 张西营; 孙国芳

    2004-01-01

    In the geological evolution of the Tarim Basin, many transgressions and relictions happened. So there have been plentiful sources of salt. Moreover, because of uttermost drought, a lot of salt has been deposited. It is possible to find potash salt in this area. In our fieldwork, we have found salt and brine in western Tarim Basin. Based on a geological survey and the characteristics of sedimentary facies and paleogeography, this paper deals with the geochemical parameters and discusses the possibility of formation of potash salt in terms of the chemical analyses of samples collected from western Tarim Basin. Results of brine analysis lead to some conclusions: most of these salt brines have eluviated from very thick halite beds, mainly chloride-type salt and this kind of halite does not reach the stage of potash deposition in all aspects; WKSL (Wukeshalu) occupies a noticeable place, and we should attach importance to this district because there have been some indicators of the occurrence of potash deposits as viewed from the contents of Br and K. Finally, low Br contents are recognized in the Tarim Basin as a result of salt aggradation, and this point of view has been proved by the results of this experiment and the data available. It cannot depend upon the index of Br to judge the evolution stage of halite. We must look for other facies of potash except marine facies.

  13. Surface boiling of superheated liquid

    Energy Technology Data Exchange (ETDEWEB)

    Reinke, P. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-01-01

    A basic vaporization mechanism that possibly affects the qualitative and quantitative prediction of the consequences of accidental releases of hazardous superheated liquids was experimentally and analytically investigated. The studies are of relevance for the instantaneous failure of a containment vessel filled with liquefied gas. Even though catastrophical vessel failure is a rare event, it is considered to be a major technological hazard. Modeling the initial phase of depressurisation and vaporization of the contents is an essential step for the subsequent analysis of the spread and dispersion of the materials liberated. There is only limited understanding of this inertial expansion stage of the superheated liquid, before gravity and atmospheric turbulence begin to dominate the expansion. This work aims at a better understanding of the vaporization process and to supply more precise source-term data. It is also intended to provide knowledge for the prediction of the behavior of large-scale releases by the investigation of boiling on a small scale. Release experiments with butane, propane, R-134a and water were conducted. The vaporization of liquids that became superheated by sudden depressurisation was studied in nucleation-site-free glass receptacles. Several novel techniques for preventing undesired nucleation and for opening the test-section were developed. Releases from pipes and from a cylindrical geometry allowed both linear one-dimensional, and radial-front two-dimensional propagation to be investigated. Releases were made to atmospheric pressure over a range of superheats. It was found that, above a certain superheat temperature, the free surface of the metastable liquid rapidly broke up and ejected a high-velocity vapor/liquid stream. The zone of intense vaporization and liquid fragmentation proceeded as a front that advanced into the test fluids. No nucleation of bubbles in the bulk of the superheated liquid was observed. (author) figs., tabs., refs.

  14. Geophysical and geochemical signatures of Gulf of Mexico seafloor brines

    Directory of Open Access Journals (Sweden)

    S. B. Joye

    2005-05-01

    Full Text Available Geophysical, temperature, and discrete depth-stratified geochemical data illustrate differences between an actively venting mud volcano and a relatively quiescent brine pool in the Gulf of Mexico along the continental slope. Geophysical data, including laser-line scan mosaics and sub-bottom profiles, document the dynamic nature of both environments. Temperature profiles, obtained by lowering a CTD into the brine fluid, show that the venting brine was at least 10°C warmer than the bottom water. At the brine pool, two thermoclines were observed, one directly below the brine-seawater interface and a second about one meter below the first. At the mud volcano, substantial temperature variability was observed, with the core brine temperature being either slightly (~2°C in 1997 or substantially (19°C in 1998 elevated above bottom water temperature. Geochemical samples were obtained using a device called the "brine trapper" and concentrations of dissolved gases, major ions and nutrients were determined using standard techniques. Both brines contained about four times as much salt as seawater and steep concentration gradients of dissolved ions and nutrients versus brine depth were apparent. Differences in the concentrations of calcium, magnesium and potassium between the two brine fluids suggests that the fluids are derived from different sources or that brine-sediment reactions are more important at the mud volcano than the brine pool. Substantial concentrations of methane and ammonium were observed in both brines, suggesting that fluids expelled from deep ocean brines are important sources of methane and dissolved inorganic nitrogen to the surrounding environment.

  15. Cryogenic Boil-Off Reduction System

    Science.gov (United States)

    Plachta, David W.; Guzik, Monica C.

    2014-03-01

    A computational model of the cryogenic boil-off reduction system being developed by NASA as part of the Cryogenic Propellant Storage and Transfer technology maturation project has been applied to a range of propellant storage tanks sizes for high-performing in-space cryogenic propulsion applications. This effort focuses on the scaling of multi-layer insulation (MLI), cryocoolers, broad area cooling shields, radiators, solar arrays, and tanks for liquid hydrogen propellant storage tanks ranging from 2 to 10 m in diameter. Component scaling equations were incorporated into the Cryogenic Analysis Tool, a spreadsheet-based tool used to perform system-level parametric studies. The primary addition to the evolution of this updated tool is the integration of a scaling method for reverse turbo-Brayton cycle cryocoolers, as well as the development and inclusion of Self-Supporting Multi-Layer Insulation. Mass, power, and sizing relationships are traded parametrically to establish the appropriate loiter period beyond which this boil-off reduction system application reduces mass. The projected benefit compares passive thermal control to active thermal control, where active thermal control is evaluated for reduced boil-off with a 90 K shield, zero boil-off with a single heat interception stage at the tank wall, and zero boil-off with a second interception stage at a 90 K shield. Parametric studies show a benefit over passive storage at loiter durations under one month, in addition to showing a benefit for two-stage zero boil-off in terms of reducing power and mass as compared to single stage zero boil-off. Furthermore, active cooling reduces the effect of varied multi-layer insulation performance, which, historically, has been shown to be significant.

  16. Lattice Boltzmann modeling of boiling heat transfer: The boiling curve and the effects of wettability

    CERN Document Server

    Li, Q; Francois, M M; He, Y L; Luo, K H

    2015-01-01

    A hybrid thermal lattice Boltzmann (LB) model is presented to simulate thermal multiphase flows with phase change based on an improved pseudopotential LB approach [Q. Li, K. H. Luo, and X. J. Li, Phys. Rev. E 87, 053301 (2013)]. The present model does not suffer from the spurious term caused by the forcing-term effect, which was encountered in some previous thermal LB models for liquid-vapor phase change. Using the model, the liquid-vapor boiling process is simulated. The boiling curve together with the three boiling stages (nucleate boiling, transition boiling, and film boiling) is numerically reproduced in the LB community for the first time. The numerical results show that the basic features and the fundamental characteristics of boiling heat transfer are well captured, such as the severe fluctuation of transient heat flux in the transition boiling and the feature that the maximum heat transfer coefficient lies at a lower wall superheat than that of the maximum heat flux. Furthermore, the effects of the he...

  17. Pure Culture Fermentation of Brined Cucumbers.

    Science.gov (United States)

    Etchells, J L; Costilow, R N; Anderson, T E; Bell, T A

    1964-11-01

    The relative abilities of Pediococcus cerevisiae, Lactobacillus plantarum, L. brevis, and several other species of lactic acid bacteria to grow and produce acid in brined cucumbers were evaluated in pure culture fermentations. Such fermentations were made possibly by the use of two techniques, gamma radiation (0.83 to 1.00 Mrad) and hot-water blanching (66 to 80 C for 5 min), designed first to rid the cucumbers of naturally occurring, interfering, and competitive microbial groups prior to brining, followed by inoculation with the desired lactic acid bacteria. Of the nine species tested, strains of the three common to cucumber fermentations, P. cerevisiae, L. plantarum, and L. brevis, grew to the highest populations, and produced the highest levels of brine acidity and the lowest pH values in fermentations at 5.4 to 5.6% NaCl by weight; also, their sequence of active development in fermentations, with the use of a three-species mixture for inoculation, was in the species order just named. This sequence of occurrence was similar to that estimated by others for natural fermentations. The rates of growth and acid production in fermentations with a mixture of P. cerevisiae, L. plantarum, and L. brevis increased as the incubation temperature was increased from 21 to 27 to 32 C; however, the maximal populations and acidities attained were essentially the same for fermentations at each temperature. Further, these same three species were found to be the most salt tolerant of those tested; their upper limit for appreciable growth and measurable acid production was about 8% salt, whereas thermophilic species such as L. thermophilus, L. lactis, L. helveticus, L. fermenti, and L. delbrueckii exhibited a much lower salt tolerance, ranging from about 2.5 to 4.0%. However, certain strains of L. delbrueckii grew very rapidly in cucumbers brined at 2.5 to 3.0% salt, and produced sufficient acid in about 30 hr at 48 C to reduce the brine pH from above 7.0 to below 4.0. An inexpensive

  18. Numerical modelling of chloride propagation in the quaternary aquifer of the southern Upper Rhine Graben

    Science.gov (United States)

    Lang, U.; Gudera, T.; Elsass, P.; Wirsing, G.

    2005-09-01

    The deep groundwater in the quaternary gravel sequence of the southern Upper Rhine Graben locally contains high chloride concentrations near the river Rhine between Fessenheim (France) in the South and Breisach (Germany) in the North. This historical pollution is mainly due to past infiltration from the former brine storage basins of the French potash mines on the “Fessenheim Island” and—to a lesser extent—from the leaching of the salt dumps of the German potash mines in Buggingen and Heitersheim. The spreading of the salt plume was investigated by means of a groundwater model. The aim of the model was to understand the brine movement, the present distribution of chloride as defined by recent hydrochemical investigations, and to select locations for new reconnaissance boreholes. The geological structure was reproduced by a three layer model, which was calibrated for steady state flow conditions. The hydraulic conductivity of the first layer was determined by comparing measured and calculated heads in the model area. The vertical resolution was refined to simulate the density-dependent salt transport processes. The transport of the salt plumes was simulated over a 40-year period, starting at the beginning of brine storage in the 1950s. The relevant transport parameters have been estimated in a sensitivity analysis, where the simulated breakthrough curves of chloride concentration have been compared with the measured data. The results of the groundwater model indicate that brines containing approximately 1 million tons of chloride are still present at the bottom of the aquifer. These highly concentrated salt brines mix with fresh water from the upper part of the aquifer. This dispersive process leads to the formation of a plume of chloride-rich water extending downstream, where pumping wells for several local water supplies are located.

  19. The Effect of adjusting PH on Stretchability and Meltability to White Brined Nabulsi Cheese

    Directory of Open Access Journals (Sweden)

    Ayman S. Mazahreh

    2009-01-01

    Full Text Available Problem statement: Boiled white brined (Nabulsi cheese is the mostly consumed in Jordan; this cheese should show meltability and high stretchability in order to fit in the production of high quality Kunafa and other popular local sweets and pastries.The most outstanding characteristic of Nabulsi cheese is the long keeping ability (more than one year without cooling, since it is preserved in concentrated brine (up to 25%. Approach: This work was based on the hypothesis that it would be possible to imply meltability and stretchability to the cheese by adjusting pH to the original brine that may specifically act on cross linking bonds of casein. A new apparatus for measuring the actual stretchability was designed and constructed; measurements on different cheeses proved its validity and reliability to measurement stretchability up to 80cm. Detailed treatments revealed the success of the proposed assumption in inducing meltability and stretchability to cheese processed and preserved according to the traditional methods. Results: The following results were obtained: It is possible to imply a low but acceptable level of stretchability and meltability through adjustment of the pH in the range of 5.4-5.8 by adding calculated amount of citric acid considering the buffering capacity of the cheese and storing it for few weeks to reach equilibrium. Conclusion: Conformational experiments proved the applicability of the new method on commercial Nabulsi cheese samples. Sensory evaluation revealed the superiority of pH adjusting treatment specifically at pH 5.4 and 5.8 as well as commercial Mashmouleh cheese that has high meltability and stretchability when used in Kunafa making.

  20. A review of film boiling at cryogenic temperatures.

    Science.gov (United States)

    Hsu, Y. Y.

    1972-01-01

    Film boiling occurs in the quenching of metals, the chilling of biological species, the regenerative cooling of rockets, and the cooling down of a cryogenic fuel tank. Occasionally film boiling is also found in a nuclear reactor or in a cryomagnet. Aspects of film boiling involving an unconstrained liquid mass are considered, giving attention to the evaporation time, the Leidenfrost temperature, solid-liquid contacts, the thermal properties of the solid, effects of coating or scale, wettability, the metastable condition, and the velocity effect on drops. Developments discussed with regard to pool boiling are related to vertical surfaces, film boiling from horizontal surfaces, film boiling from a horizontal cylinder, film boiling from a sphere, and film boiling of helium. Processes of film boiling in a channel are also analyzed.

  1. A preliminary deposit model for lithium brines

    Science.gov (United States)

    Bradley, Dwight; Munk, LeeAnn; Jochens, Hillary; Hynek, Scott; Labay, Keith A.

    2013-01-01

    This report is part of an effort by the U.S. Geological Survey to update existing mineral deposit models and to develop new ones. The global transition away from hydrocarbons toward energy alternatives increases demand for many scarce metals. Among these is lithium, a key component of lithium-ion batteries for electric and hybrid vehicles. Lithium brine deposits account for about three-fourths of the world’s lithium production. Updating an earlier deposit model, we emphasize geologic information that might directly or indirectly help in exploration for lithium brine deposits, or for assessing regions for mineral resource potential. Special attention is given to the best-known deposit in the world—Clayton Valley, Nevada, and to the giant Salar de Atacama, Chile.

  2. Brine shrimp lethality assay of Bacopa monnieri.

    Science.gov (United States)

    D'Souza, Prashanth; Deepak, Mundkinajeddu; Rani, Padmaja; Kadamboor, Sandhya; Mathew, Anjana; Chandrashekar, Arun P; Agarwal, Amit

    2002-03-01

    Successive petroleum ether, chloroform, ethanol and water extracts, a saponin rich fraction (SRF) and bacoside A isolated from Bacopa monnieri were tested for brine shrimp lethality. Successive ethanol extracts and SRF showed potent activity. Bacoside A showed the maximum activity with a LC(50) of 38.3 microg/mL. The results confirmed the previous reports of an anticancer effect of Bacopa monnieri and suggest bacoside A as the active constituent.

  3. 卤水中氧化镁提取工艺研究%Brine Preparation of Magnesium Oxide Process

    Institute of Scientific and Technical Information of China (English)

    向群; 王蓉

    2012-01-01

    The paper asks about extracting magnesium oxide from the brine. Brine-soda method to the purification of brine by adding sodium carbonate, the preparation of basic magnesium carbonate, basic magnesium carbonate magnesium oxide after calcination. The experimental results show that the Barium chloride concentration of 0.13 mol/L, and the water bath temperature of 40 ℃, feed rate the 5 mL/min, aging time for lh brine purification best. The ratio of raw materials to 110 %, the reaction temperature is 60℃, reaction time was 30 min, and Magnesium oxide yield.%采用卤水-纯碱法,向经过净化的卤水中加入碳酸钠,制取碱式碳酸镁,经过煅烧得到氧化镁。实验结果表明:反应浓度O.13mol/L、反应温度40℃、加科速度5mL/min、陈化时间1h时卤水的净化效果较好。原料配比110%、反应温度60℃、反应时间30min时氧化镁的收率较好。

  4. Delineation of brine contamination in and near the East Poplar oil field, Fort Peck Indian Reservation, northeastern Montana, 2004-09

    Science.gov (United States)

    Thamke, Joanna N.; Smith, Bruce D.

    2014-01-01

    The extent of brine contamination in the shallow aquifers in and near the East Poplar oil field is as much as 17.9 square miles and appears to be present throughout the entire saturated zone in contaminated areas. The brine contamination affects 15–37 billion gallons of groundwater. Brine contamination in the shallow aquifers east of the Poplar River generally moves to the southwest toward the river and then southward in the Poplar River valley. The likely source of brine contamination in the shallow aquifers is brine that is produced with crude oil in the East Poplar oil field study area. Brine contamination has not only affected the water quality from privately owned wells in and near the East Poplar oil field, but also the city of Poplar’s public water-supply wells. Three water-quality types characterize water in the shallow aquifers; a fourth water-quality type in the study area characterizes the brine. Type 1 is uncontaminated water that is suitable for most domestic purposes and typically contains sodium bicarbonate and sodium/magnesium sulfate as the dominant ions. Type 2 is moderately contaminated water that is suitable for some domestic purposes, but not used for drinking water, and typically contains sodium and chloride as the dominant ions. Type 3 is considerably contaminated water that is unsuitable for any domestic purpose and always contains sodium and chloride as the dominant ions. Type 3 quality of water in the shallow aquifers is similar to Type 4, which is the brine that is produced with crude oil. Electromagnetic apparent conductivity data were collected in the 106 square-mile area and used to determine extent of brine contamination. These data were collected and interpreted in conjunction with water-quality data collected through 2009 to delineate brine plumes in the shallow aquifers. Monitoring wells subsequently were drilled in some areas without existing water wells to confirm most of the delineated brine plumes; however, several possible

  5. The entropy balance for boiling flow

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco-Javier E-mail: fjk@posta.unizar.es

    2001-10-01

    Subcooled forced convection boiling of water is recognized as one of the best means of accommodating the very high heat fluxes that plasma facing components of fusion reactors have to withstand. The boiling curve, giving the wall temperature in function of the applied flux and flow conditions, is essential for the design of such cooling configurations. In this paper, a new entropy balance for subcooled boiling flow, which allows the wall temperature to be obtained, is presented and successfully compared with experimental data from the Joint US-EURATOM R and D Program. The derivation of this entropy balance is based on a new strict application of the Reynolds theorem to multiphase flows recently proposed by the author.

  6. Thermodynamics of Flow Boiling Heat Transfer

    Science.gov (United States)

    Collado, F. J.

    2003-05-01

    Convective boiling in sub-cooled water flowing through a heated channel is essential in many engineering applications where high heat flux needs to be accommodated. It has been customary to represent the heat transfer by the boiling curve, which shows the heat flux versus the wall-minus-saturation temperature difference. However it is a rather complicated problem, and recent revisions of two-phase flow and heat transfer note that calculated values of boiling heat transfer coefficients present many uncertainties. Quite recently, the author has shown that the average thermal gap in the heated channel (the wall temperature minus the average temperature of the coolant) was tightly connected with the thermodynamic efficiency of a theoretical reversible engine placed in this thermal gap. In this work, whereas this correlation is checked again with data taken by General Electric (task III) for water at high pressure, a possible connection between this wall efficiency and the reversible-work theorem is explored.

  7. Boiling on Microconfigured Composite Surfaces Enhanced

    Science.gov (United States)

    Chao, David F.

    2000-01-01

    Boiling heat transfer is one of the key technologies for the two-phase active thermal-control system used on space platforms, as well as for the dynamic power systems aboard the International Space Station. Because it is an effective heat transfer mode, boiling is integral to many space applications, such as heat exchangers and other cooling devices. Nucleate boiling near the critical heat flux (CHF) can transport very large thermal loads with a much smaller device and much lower pumping power than for single-phase heat exchangers. However, boiling performance sharply deteriorates in a reduced-gravity environment, and operation in the CHF regime is somewhat perilous because of the risk of burnout to the device surface. New materials called microconfigured metal-graphite composites can enhance boiling. The photomicrograph shows the microconfiguration (x3000) of the copper-graphite (Cu-Gr) surface as viewed by scanning electronic microscope. The graphite fiber tips appear as plateaus with rugged surfaces embedded in the copper matrix. It has been experimentally demonstrated that this type of material manifests excellent boiling heat transfer performance characteristics and an increased CHF. Nonisothermal surfaces were less sensitive to variations of wall superheat in the CHF regime. Because of the great difference in conductivity between the copper base and the graphite fiber, the composite surfaces have a nonisothermal surface characteristic and, therefore, will have a much larger "safe" operating region in the CHF regime. In addition, the thermocapillary forces induced by the temperature differences between the fiber tips and the metal matrix play an important role in bubble detachment, and may not be adversely affected in a reduced-gravity environment. All these factors indicate that microconfigured composites may improve the reliability and economy (dominant factors in all space applications) of various thermal components found on spacecraft during future

  8. Brines as Sources of Long-term Subsurface Contamination

    Science.gov (United States)

    Flowers, T. C.; Hunt, J. R.

    2004-12-01

    Concentrated salt solutions, i.e. brines, are source terms for environmental contaminants released into surface waters and groundwaters. Brines arise from both natural and industrial processes such as natural salt deposits, solid rocket fuel production, landfill leachates, nuclear fuel reprocessing, and acid rock drainage. Additionally, many of the in-situ remediation fluids that have been implemented at the pilot or the field scale are also classified as brines. While brines are miscible with water, mixing processes are slow in the subsurface and this constrains the dilution of contaminants present within brines and the delivery of remediation fluids to sites where reactions are needed. The mixing of brines during their vertical migration through aquifers is determined by aquifer permeability as well as differences in density and viscosity between the brine and the ambient groundwater. The stability criterion for brine displacement was predicted in 1952 by Hill and the resulting dispersion at the mixing front is quantified by a compilation of literature data and the acquisition of new experimental data. As brines sink through aquifers, they become emplaced in less accessible locations where mass transfer models predict that contaminants within brines are slowly released into flowing groundwater. For radioactive wastes and environmental contaminants with very low acceptable concentrations, groundwater quality can be impacted for decades. Field data from a cooling water disposal site suggest that a dense brine is likely still present as a source term 40 years after waste disposal was stopped. Overall, analysis of pollution sources, quantification of transport processes, generalization of laboratory data, and limited evaluation of field data indicate that brines represent long-term sources of groundwater contamination and that source control has not been seriously addressed.

  9. Geophysical and geochemical signatures of Gulf of Mexico seafloor brines

    Directory of Open Access Journals (Sweden)

    S. B. Joye

    2005-01-01

    Full Text Available Geophysical, temperature, and discrete depth-stratified geochemical data illustrate differences between an actively venting mud volcano and a relatively quiescent brine pool in the Gulf of Mexico along the continental slope. Geophysical data, including laser-line scan mosaics and sub-bottom profiles, document the dynamic nature of both environments. Temperature profiles, obtained by lowering a CTD into the brine fluid, show that the venting brine was at least 10°C warmer than the bottom water. At the brine pool, thermal stratification was observed and only small differences in stratification were documented between three sampling times (1991, 1997 and 1998. In contrast, at the mud volcano, substantial temperature variability was observed, with the core brine temperature being slightly higher than bottom water (by 2°C in 1997 but substantially higher than bottom water (by 19°C in 1998. Detailed geochemical samples were obtained in 2002 using a device called the 'brine trapper' and concentrations of dissolved gases, major ions and nutrients were determined. Both brines contained about four times as much salt as seawater and steep concentration gradients of dissolved ions and nutrients versus brine depth were apparent. Differences in the concentrations of calcium, magnesium and potassium between the two brine fluids suggest that the fluids are derived from different sources, have different dilution/mixing histories, or that brine-sediment reactions are more important at the mud volcano. Substantial concentrations of methane, ammonium, and silicate were observed in both brines, suggesting that fluids expelled from deep ocean brines are important sources of these constituents to the surrounding environment.

  10. SYNTHESIS OF POLYMER-STABILIZED RUTHENIUM COLLOIDS BY LOW BOILING POINT ALCOHOL REDUCTION

    Institute of Scientific and Technical Information of China (English)

    Ya-li Su; Xiu-ru Li; Yue-jin Tong; Yue-sheng Li

    2003-01-01

    Stable and well-dispersed poly(N-vinyl-2-pyrrolidone) (PVP)-stabilized ruthenium colloidal clusters were prepared via the reduction of ruthenium(Ⅲ) chloride by refluxing with low boiling point alcohols. Investigation of the size of Ru colloids by transmission electron microscopy (TEM) indicated that the average diameters could be controlled in the range of 1.2-1.6 nm with relative standard deviations of less than 0.33 by changing the molar ratio of PVP to Ru. The X-ray photoelectron spectroscopy (XPS) characterization verified the formation of elemental ruthenium colloids.

  11. Preliminary Feasibility Testing of the BRIC Brine Water Recovery Concept

    Science.gov (United States)

    Callahan, Michael R.; Pensinger, Stuart; Pickering, Karen D.

    2011-01-01

    The Brine Residual In-Containment (BRIC) concept was developed as a new technology to recover water from spacecraft wastewater brines. Such capability is considered critical to closing the water loop and achieving a sustained human presence in space. The intention of the BRIC concept is to increase the robustness and efficiency of the dewatering process by performing drying inside the container used for the final disposal of the residual brine solid. Recent efforts in the development of BRIC have focused on preliminary feasibility testing using a laboratory- assembled pre-prototype unit. Observations of the drying behavior of actual brine solutions processed under BRIC-like conditions has been of particular interest. To date, experiments conducted with three types of analogue spacecraft wastewater brines have confirmed the basic premise behind the proposed application of in-place drying for these solutions. Specifically, the dried residual mass from these solutions have tended to exhibit characteristics of adhesion and flow that are expected to continue to challenge process stream management in spacecraft brine dewatering system designs. Yet, these same characteristics may favor the development of capillary- and surface-tension-based approaches envisioned as part of an ultimate microgravity-compatible BRIC design. In addition, preliminary feasibility testing of the BRIC pre-prototype confirmed that high rates of water recovery, up to 98% of the available brine water, may be possible while still removing the majority of the brine contaminants from the influent brine stream. These and other observations from testing are reported.

  12. Evaluation of Brine Processing Technologies for Spacecraft Wastewater

    Science.gov (United States)

    Shaw, Hali L.; Flynn, Michael; Wisniewski, Richard; Lee, Jeffery; Jones, Harry; Delzeit, Lance; Shull, Sarah; Sargusingh, Miriam; Beeler, David; Howard, Jeanie; Howard, Kevin; Harris, Linden; Parodi, Jurek; Kawashima, Brian

    2015-01-01

    Brine drying systems may be used in spaceflight. There are several advantages to using brine processing technologies for long-duration human missions including a reduction in resupply requirements and achieving high water recovery ratios. The objective of this project was to evaluate four technologies for the drying of spacecraft water recycling system brine byproducts. The technologies tested were NASA's Forward Osmosis Brine Drying (FOBD), Paragon's Ionomer Water Processor (IWP), NASA's Brine Evaporation Bag (BEB) System, and UMPQUA's Ultrasonic Brine Dewatering System (UBDS). The purpose of this work was to evaluate the hardware using feed streams composed of brines similar to those generated on board the International Space Station (ISS) and future exploration missions. The brine formulations used for testing were the ISS Alternate Pretreatment and Solution 2 (Alt Pretreat). The brines were generated using the Wiped-film Rotating-disk (WFRD) evaporator, which is a vapor compression distillation system that is used to simulate the function of the ISS Urine Processor Assembly (UPA). Each system was evaluated based on the results from testing and Equivalent System Mass (ESM) calculations. A Quality Function Deployment (QFD) matrix was also developed as a method to compare the different technologies based on customer and engineering requirements.

  13. An Investigation of Graduate Scientists' Understandings of Evaporation and Boiling.

    Science.gov (United States)

    Goodwin, Alan; Orlik, Yuri

    2000-01-01

    Uses a video presentation of six situations relating to the evaporation and boiling of liquids and the escape of dissolved gases from solution and investigates graduate scientists' understanding of the concepts of boiling and evaporation. (Author/YDS)

  14. Heat transfer coefficient for boiling carbon dioxide

    DEFF Research Database (Denmark)

    Knudsen, Hans Jørgen Høgaard; Jensen, Per Henrik

    1998-01-01

    Heat transfer coefficient and pressure drop for boiling carbon dioxide (R744) flowing in a horizontal pipe has been measured. The calculated heat transfer coeeficient has been compared with the Chart correlation of Shah. The Chart Correlation predits too low heat transfer coefficient but the ratio...

  15. Heat transfer coeffcient for boiling carbon dioxide

    DEFF Research Database (Denmark)

    Knudsen, Hans Jørgen Høgaard; Jensen, Per Henrik

    1997-01-01

    Heat transfer coefficient and pressure drop for boiling carbon dioxide (R744) flowing in a horizontal pipe has been measured. The pipe is heated by condensing R22 outside the pipe. The heat input is supplied by an electrical heater wich evaporates the R22. With the heat flux assumed constant over...

  16. Electrically Driven Liquid Film Boiling Experiment

    Science.gov (United States)

    Didion, Jeffrey R.

    2016-01-01

    This presentation presents the science background and ground based results that form the basis of the Electrically Driven Liquid Film Boiling Experiment. This is an ISS experiment that is manifested for 2021. Objective: Characterize the effects of gravity on the interaction of electric and flow fields in the presence of phase change specifically pertaining to: a) The effects of microgravity on the electrically generated two-phase flow. b) The effects of microgravity on electrically driven liquid film boiling (includes extreme heat fluxes). Electro-wetting of the boiling section will repel the bubbles away from the heated surface in microgravity environment. Relevance/Impact: Provides phenomenological foundation for the development of electric field based two-phase thermal management systems leveraging EHD, permitting optimization of heat transfer surface area to volume ratios as well as achievement of high heat transfer coefficients thus resulting in system mass and volume savings. EHD replaces buoyancy or flow driven bubble removal from heated surface. Development Approach: Conduct preliminary experiments in low gravity and ground-based facilities to refine technique and obtain preliminary data for model development. ISS environment required to characterize electro-wetting effect on nucleate boiling and CHF in the absence of gravity. Will operate in the FIR - designed for autonomous operation.

  17. Cryogenic Propellant Boil-Off Reduction System

    Science.gov (United States)

    Plachta, D. W.; Christie, R. J.; Carlberg, E.; Feller, J. R.

    2008-03-01

    Lunar missions under consideration would benefit from incorporation of high specific impulse propellants such as LH2 and LO2, even with their accompanying boil-off losses necessary to maintain a steady tank pressure. This paper addresses a cryogenic propellant boil-off reduction system to minimize or eliminate boil-off. Concepts to do so were considered under the In-Space Cryogenic Propellant Depot Project. Specific to that was an investigation of cryocooler integration concepts for relatively large depot sized propellant tanks. One concept proved promising—it served to efficiently move heat to the cryocooler even over long distances via a compressed helium loop. The analyses and designs for this were incorporated into NASA Glenn Research Center's Cryogenic Analysis Tool. That design approach is explained and shown herein. Analysis shows that, when compared to passive only cryogenic storage, the boil-off reduction system begins to reduce system mass if durations are as low as 40 days for LH2, and 14 days for LO2. In addition, a method of cooling LH2 tanks is presented that precludes development issues associated with LH2 temperature cryocoolers.

  18. Contact Angle Effects in Boiling Heat Transfer

    OpenAIRE

    Urquiola, Erwin; Fujita, Yasunobu

    2002-01-01

    This paper reports boiling experiments with pure water and surfactant solutions of SDS on horizontal heating surface. The static contact angle, rather than the surface tension value, was found to be the leading factor for the results and probably its prev

  19. Bubble Behavior in Nucleate Boiling Experiment Aboard the Space Shuttle

    OpenAIRE

    Koeln, Justin P.; Boulware, Jeffrey C.; Ban, Heng

    2009-01-01

    Boiling dynamics in microgravity need to be better understood before heat transfer systems based on boiling mechanism can be developed for space applications. This paper presents the results of a nucleate boiling experiment aboard Space Shuttle Endeavor (STS- 108). The experiment utilized nickel-chromium resistance wire to boil water in microgravity, and the data was recorded with a CCD camera and six thermistors. This data was analyzed to determine the behavior of bubble formation, detachmen...

  20. Selective Recovery of Metals from Geothermal Brines

    Energy Technology Data Exchange (ETDEWEB)

    Ventura, Susanna [SRI International, Menlo Park, CA (United States); Bhamidi, Srinivas [SRI International, Menlo Park, CA (United States); Hornbostel, Marc [SRI International, Menlo Park, CA (United States); Nagar, Anoop [SRI International, Menlo Park, CA (United States); Perea, Elisabeth [SRI International, Menlo Park, CA (United States)

    2016-12-16

    The objective of this project was to determine the feasibility of developing a new generation of highly selective low-cost ion-exchange resins based on metal-ion imprinted polymers for the separation of metals from geothermal fluids. Expansion of geothermal energy production over the entire U.S. will involve exploitation of low-to-medium temperature thermal waters. Creating value streams from the recovery of critical and near-critical metals from these thermal waters will encourage geothermal expansion. Selective extraction of metals from geothermal fluids is needed to design a cost-effective process for the recovery of lithium and manganese-two near-critical metals with well-known application in the growing lithium battery industry. We have prepared new lithium- and manganese-imprinted polymers in the form of beads by crosslinking polymerization of a metal polymerizable chelate, where the metal acts as a template. Upon leaching out the metal template, the crosslinked polymer is expected to leave cavities defined by the ligand functional group with enhanced selectivity for binding the template metal. We have demonstrated that lithium- and manganese-imprinted polymer beads can be used as selective solid sorbents for the extraction of lithium and manganese from brines. The polymers were tested both in batch extractions and packed bed lab-scale columns at temperatures of 45-100°C. Lithium-imprinted polymers were found to have Li+ adsorption capacity as high as 2.8 mg Li+/g polymer at 45°C. Manganese-imprinted polymers were found to have a Mn2+ adsorption capacity of more than 23 mg Mn2+/g polymer at 75°C. The Li+ extraction efficiency of the Li-imprinted polymer was found to be more that 95% when a brine containing 390 ppm Li+, 410 ppm Na+, and 390 ppm K+ was passed through a packed bed of the polymer in a lab-scale column at 45°C. In brines containing 360 ppm Li

  1. The law of stable equilibrium and the entropy-based boiling curve for flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Collado, F.J. [Universidad de Zaragoza (Spain). Dpto. Ingenieria Mecanica Motores Termicos

    2005-05-01

    Convective flow boiling in sub-cooled fluids is recognized as one of the few means of accommodating very high heat fluxes. There are many available correlations for predicting the inner wall temperature of the heated duct in the several regimes of the empirical Nukiyama boiling curve, although unfortunately there is no physical fundamentals of such curve. Recently, the author has shown that the classical entropy balance could contain key information about boiling heat transfer. So, it was found that the average thermal gap in the heated channel (the inner wall temperature minus the average temperature of the coolant fluid) was strongly correlated with the efficiency of a theoretical reversible engine placed in this thermal gap. From this new correlation, a new boiling curve plotting the wall temperature versus the average fluid temperature was derived and successfully checked against low- and high-pressure water data. This curve suggested a new and simple definition of the critical heat flux (CHF) namely, the value of the coolant average temperature at the maximum. In this work, after briefly reviewing the entropy balance of a non-equilibrium boiling flow and its relationship with the thermodynamic average temperature and the law of stable equilibrium (LSE), the possibilities of the new approach for the design of flow boiling cooling systems are highlighted. Finally, the strong correlation found between the reversible engine efficiency and the thermal driving force is verified again, now with high-pressure refrigerant 22 (R-22) data. (author)

  2. Extractive process for preparing high purity magnesium chloride hexahydrate

    Directory of Open Access Journals (Sweden)

    Fezei Radouanne

    2012-01-01

    Full Text Available This paper refers a method for the preparation of magnesium chloride hexahydrate (bischofite from Sebkha el Melah of Zarzis Tunisian natural brine. It is a five-stage process essentially based on crystallization by isothermal evaporation and chemical precipitation. The two first steps were dedicated to the crystallization of sodium chloride and potassiummagnesium double salts, respectively. Then, the resulting liquor was desulfated using calcium chloride solution. After that another isothermal evaporation stage was implemented in order to eliminate potassium ions in the form of carnallite, KCl.MgCl2.6H2O. At the end of this step, the recovered solution primarily composed of magnesium and chloride ions was treated by dioxan in order to precipitate magnesium chloride as MgCl2.6H2O.C4H8O2. This compound dried at constant temperature of 100°C gave good quality magnesium chloride hexahydrate. Besides this salt, the various by-products obtained from the different treatment stages are also useful.

  3. Thermohydrodynamics of boiling in a van der Waals fluid.

    Science.gov (United States)

    Laurila, T; Carlson, A; Do-Quang, M; Ala-Nissila, T; Amberg, G

    2012-02-01

    We present a modeling approach that enables numerical simulations of a boiling Van der Waals fluid based on the diffuse interface description. A boundary condition is implemented that allows in and out flux of mass at constant external pressure. In addition, a boundary condition for controlled wetting properties of the boiling surface is also proposed. We present isothermal verification cases for each element of our modeling approach. By using these two boundary conditions we are able to numerically access a system that contains the essential physics of the boiling process at microscopic scales. Evolution of bubbles under film boiling and nucleate boiling conditions are observed by varying boiling surface wettability. We observe flow patters around the three-phase contact line where the phase change is greatest. For a hydrophilic boiling surface, a complex flow pattern consistent with vapor recoil theory is observed.

  4. Enhanced Droplet Control by Transition Boiling

    Science.gov (United States)

    Grounds, Alex; Still, Richard; Takashina, Kei

    2012-10-01

    A droplet of water on a heated surface can levitate over a film of gas produced by its own evaporation in the Leidenfrost effect. When the surface is prepared with ratchet-like saw-teeth topography, these droplets can self-propel and can even climb uphill. However, the extent to which the droplets can be controlled is limited by the physics of the Leidenfrost effect. Here, we show that transition boiling can be induced even at very high surface temperatures and provide additional control over the droplets. Ratchets with acute protrusions enable droplets to climb steeper inclines while ratchets with sub-structures enable their direction of motion to be controlled by varying the temperature of the surface. The droplets' departure from the Leidenfrost regime is assessed by analysing the sound produced by their boiling. We anticipate these techniques will enable the development of more sophisticated methods for controlling small droplets and heat transfer.

  5. Dynamic Bubble Behaviour during Microscale Subcooled Boiling

    Institute of Scientific and Technical Information of China (English)

    WANG Hao; PENG Xiao-Feng; David M.Christopher

    2005-01-01

    @@ Bubble cycles, including initiation, growth and departure, are the physical basis of nucleate boiling. The presentinvestigation, however, reveals unusual bubble motions during subcooled nucleate boiling on microwires 25 orl00μm in diameter. Two types of bubble motions, bubble sweeping and bubble return, are observed in theexperiments. Bubble sweeping describes a bubble moving back and forth along the wire, which is motion parallelto the wire. Bubble return is the bubble moving back to the wire after it has detached or leaping above thewire. Theoretical analyses and numerical simulations are conducted to investigate the driving mechanisms forboth bubble sweeping and return. Marangoni flow from warm to cool regions along the bubble interface is foundto produce the shear stresses needed to drive these unusual bubble movements.

  6. Pool Boiling Heat Transfer on structured Surfaces

    Science.gov (United States)

    Addy, J.; Olbricht, M.; Müller, B.; Luke, A.

    2016-09-01

    The development in the process and energy sector shows the importance of efficient utilization of available resources to improve thermal devices. To achieve this goal, all thermal components have to be optimized continuously. Various applications of multi-phase heat and mass transfer have to be improved. Therefore, the heat transfer and the influence of surface roughness in nucleate boiling with the working fluid propane is experimentally investigated on structured mild steel tubes, because only few data are available in the literature. The mild steel tube is sandblasted to obtain different surface roughness. The measurements are carried out over wide ranges of heat flux and pressure. The experimental results are compared with correlations from literature and the effect of surface roughness on the heat transfer is discussed. It is shown that the heat transfer coefficient increases with increasing surface roughness, heat flux and reduced pressure at nucleate pool boiling.

  7. Boiling Heat Transfer in Circulating Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    张利斌; 李修伦

    2001-01-01

    A model is proposed to predict boiling heat transfer coefficient in a three-phase circulating fluidized bed (CFB), which is a new type of evaporation boiling means for enhancing heat transfer and preventing fouling. To verify the model, experiments are conducted in a stainless steel column with 39 mm ID and 2.0 m height, in which the heat transfer coefficient is measured for different superficial velocities, steam pressures, particle concentrations and materials of particle. As the steam pressure and particle concentrations increase, the heat transfer coefficient in the bed increases. The heat transfer coefficient increases with the liquid velocity but it exhibits a local minimum.The heat transfer coefficient is correlated with cluster renewed model and two-mechanism method. The prediction of the model is in good agreement with experimental data.

  8. Boiling Heat Transfer in Circulating Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A model is proposed to predict boiling heat transfer coefficient in a three-phase circulating fluidized bed (CFB), which is a new type of evaporation boiling means for enhancing heat transfer and preventing fouling. To verify the model, experiments are conducted in a stainless steel column with 39mm ID and 2.0m height, in which the heat transfer coefficient is measured for different superficial velocities, steam pressures, particle concentrations and materials of particle. As the steam pressure and particle concentrations increase, the heat transfer coefficient in the bed increases. The heat transfer coefficient increases with the liquid velocity but it exhibits a local minimum. The heat transfer coefficient is correlated with cluster renewed model and two-mechanism method. The prediction of the model is in good agreement with experimental data.

  9. Self-propelled film-boiling liquids

    OpenAIRE

    Linke, H.; Aleman, B. J.; Melling, L. D.; Taormina, M. J.; Francis, M J; Dow-Hygelund, C. C.; Narayanan, V.; Taylor, R. P.; Stout, A.

    2005-01-01

    We report that liquids perform self-propelled motion when they are placed in contact with hot surfaces with asymmetric (ratchet-like) topology. The pumping effect is observed when the liquid is in the film-boiling regime, for many liquids and over a wide temperature range. We propose that liquid motion is driven by a viscous force exerted by vapor flow between the solid and the liquid.

  10. Pressure drop in saturated flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco J. [Universidad de Zaragoza, Zaragoza (Spain)

    2003-07-01

    A new mass balance for flow boiling have been recently suggested by the author following a quite simple idea: if the phases have different velocities, they can not cover the same distance -the control volume length for a 1-d system- in the same time. Thus, the time scales of the phases have to be different, and we should scale the time dependent magnitudes of one phase to the other one before combining them. Furthermore, it is reasonable to think that conservation equations should have to include in some manner this evident physical fact. In complete coherence with the former mass balance, a new energy balance, which does include the slip ratio has been also stated. This work, whilst reviews these new fundamentals for saturated flow boiling, stresses those aspects related with the prediction of the pressure drop in saturated flow boiling. The new correlations found for the data carefully measured by Thom during the Cambridge project would confirm the new two-phase flowapproach.

  11. Flow boiling test of GDP replacement coolants

    Energy Technology Data Exchange (ETDEWEB)

    Park, S.H. [comp.

    1995-08-01

    The tests were part of the CFC replacement program to identify and test alternate coolants to replace CFC-114 being used in the uranium enrichment plants at Paducah and Portsmouth. The coolants tested, C{sub 4}F{sub 10} and C{sub 4}F{sub 8}, were selected based on their compatibility with the uranium hexafluoride process gas and how well the boiling temperature and vapor pressure matched that of CFC-114. However, the heat of vaporization of both coolants is lower than that of CFC-114 requiring larger coolant mass flow than CFC-114 to remove the same amount of heat. The vapor pressure of these coolants is higher than CFC-114 within the cascade operational range, and each coolant can be used as a replacement coolant with some limitation at 3,300 hp operation. The results of the CFC-114/C{sub 4}F{sub 10} mixture tests show boiling heat transfer coefficient degraded to a minimum value with about 25% C{sub 4}F{sub 10} weight mixture in CFC-114 and the degree of degradation is about 20% from that of CFC-114 boiling heat transfer coefficient. This report consists of the final reports from Cudo Technologies, Ltd.

  12. Steady State Vapor Bubble in Pool Boiling

    Science.gov (United States)

    Zou, An; Chanana, Ashish; Agrawal, Amit; Wayner, Peter C.; Maroo, Shalabh C.

    2016-02-01

    Boiling, a dynamic and multiscale process, has been studied for several decades; however, a comprehensive understanding of the process is still lacking. The bubble ebullition cycle, which occurs over millisecond time-span, makes it extremely challenging to study near-surface interfacial characteristics of a single bubble. Here, we create a steady-state vapor bubble that can remain stable for hours in a pool of sub-cooled water using a femtosecond laser source. The stability of the bubble allows us to measure the contact-angle and perform in-situ imaging of the contact-line region and the microlayer, on hydrophilic and hydrophobic surfaces and in both degassed and regular (with dissolved air) water. The early growth stage of vapor bubble in degassed water shows a completely wetted bubble base with the microlayer, and the bubble does not depart from the surface due to reduced liquid pressure in the microlayer. Using experimental data and numerical simulations, we obtain permissible range of maximum heat transfer coefficient possible in nucleate boiling and the width of the evaporating layer in the contact-line region. This technique of creating and measuring fundamental characteristics of a stable vapor bubble will facilitate rational design of nanostructures for boiling enhancement and advance thermal management in electronics.

  13. Chemical Composition and Enzymes Inhibitory, Brine Shrimp Larvae Toxicity, Antimicrobial and Antioxidant Activities of Caloplaca biatorina

    Directory of Open Access Journals (Sweden)

    Tahereh Valadbeigi

    2016-10-01

    Full Text Available Background This study evaluated the brine shrimp larvae toxicity and enzymes inhibitory especially anti-diabetic potential of Caloplaca biatorina via in vitro inhibition of α-amylase and α-glucosidase using the methanol extracts. Also aldehyde oxidase and xanthine oxidase enzymes inhibitory, cytotoxicity, and antioxidant activities of the species were determined. Methods In this experimental study, different concentrations of the extracts (0.2, 5.0, 1 and 1.5 mg/mL were incubated with enzyme substrate solution and the percentage of enzyme inhibitory activity and IC50 was calculated. Folin- Ciocalteu reagent and aluminium chloride colorimetric methods were used to estimate total phenolic and flavonoid content of extracts. The toxicity of the extract was assessed using the brine shrimp lethality bioassay. The minimal inhibitory concentration (MIC and minimum bactericidal concentration (MBC were determined. High-performance liquid chromatography and Thin-layer chromatography analysis were evaluated. The data were analyzed by SPSS V.21 software. Results Parietin, Emodin, 1,8-Dihydroxy-3-(hydroxymethyl-6- methoxy-9.10-anthracenedione and Rhein were identified. The extract showed strong α-glucosidase, aldehyde oxidase and xanthine oxidase inhibitory activities with IC50 value of 17.12, 40.09 and 11.02 µg/mL respectively. Also methanol extract displayed the strongest DPPH radical scavenging and brine shrimp toxicity (IC50 = 91.11 properties. Conclusions The result obtained suggests that the C. biatorina extract can be classified as non-toxic. Also, it revealed the antioxidant and antidiabetic potential of the lichen.

  14. Stability monitoring for boiling water reactors

    Science.gov (United States)

    Cecenas-Falcon, Miguel

    1999-11-01

    A methodology is presented to evaluate the stability properties of Boiling Water Reactors based on a reduced order model, power measurements, and a non-linear estimation technique. For a Boiling Water Reactor, the feedback reactivity imposed by the thermal-hydraulics has an important effect in the system stability, where the dominant contribution to this feedback reactivity is provided by the void reactivity. The feedback reactivity is a function of the operating conditions of the system, and cannot be directly measured. However, power measurements are relatively easy to obtain from the nuclear instrumentation and process computer, and are used in conjunction with a reduced order model to estimate the gain of the thermal-hydraulics feedback using an Extended Kalman Filter. The reduced order model is obtained by estimating the thermal-hydraulic transfer function from the frequency-domain BWR code LAPUR, and the stability properties are evaluated based on the pair of complex conjugate eigenvalues. Because of the recursive nature of the Kalman Filter, an estimate of the decay ratio is generated every sampling time, allowing continuous estimation of the stability parameters. A test platform based on a nuclear-coupled boiling channel is developed to validate the capability of the BWR stability monitoring methodology. The thermal-hydraulics for the boiling channel is modeled and coupled with neutron kinetics to analyze the non-linear dynamics of the closed-loop system. The model uses point kinetics to study core-wide oscillations, and normalized modal kinetics are introduced to study out-of-phase oscillations. The coolant flow dynamics is dominant in the power fluctuations observed by in-core nuclear instrumentation, and additive white noise is added to the solution for the channel flow in the thermal-hydraulic model to generate noisy power time series. The operating conditions of the channel can be modified to accommodate a wide range of stability conditions

  15. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents the state-of-the art: an analytical model which describes chloride profiles in concrete as function of depth...... makes physical sense for the design engineer, i.e. the achieved chloride diffusion coefficients at 1 year and 100 years, D1 and D100 respectively, and the corresponding achieved chloride concentrations at the exposed concrete surface, C1 and C100. Data from field exposure supports the assumption of time...... dependent surface chloride concentrations and the diffusion coefficients. Model parameters for Portland cement concretes with and without silica fume and fly ash in marine atmospheric and submerged South Scandinavian environment are suggested in a companion paper based on 10 years field exposure data....

  16. Experimental study about ONB and subcooled boiling heat transfer

    Energy Technology Data Exchange (ETDEWEB)

    Changhong, P.; Myint, A.; Yun, G.; Dounan, J. [State Key Laboratory of Multiphase Flow in power engineering, Department of Nuclear and Thermal Power Engineering, Xian (China)

    2004-07-01

    Water subcooled boiling heat transfer were experimentally investigated in the vertical annuli with narrow gap. Subcooled flow boiling covers the region from the location where the bubbles forms on the wall to the location where the bulk temperature reaches saturated temperature. Three locations in the subcooled flow boiling have been identified by earlier researchers as the onset of nucleate boiling (ONB), the beginning of fully developed boiling, and the location where the thermodynamic quality is zero that is inferred from the enthalpy balance equation. The heat transfer regions are identified as single-phase heat transfer prior to ONB, partial boiling (PB) and fully developed boiling (FDB). In this study, the available models for predicting heat transfer in the different regions and the modified correlation can predict our experimental data: -) the heat flux of ONB can be predicted by the Unal correlation, nevertheless the h{sub FC} is calculated by the modified Dittus-Boelter correlations in the narrow annuli, -) Griffith's method can be modified to identify the beginning of fully develop boiling, -) in the partial boiling region, the heat transfer coefficient can be calculated by h{sub PB} equals (1-a)*h{sub L} + a*h{sub FDB}, and -) in the fully developed region, the correlation for saturated flow boiling can be employed to describe the heat transfer.

  17. A GIS-based vulnerability assessment of brine contamination to aquatic resources from oil and gas development in eastern Sheridan County, Montana

    Science.gov (United States)

    Preston, Todd M.; Chesley-Preston, Tara L.; Thamke, Joanna N.

    2014-01-01

    Water (brine) co-produced with oil in the Williston Basin is some of the most saline in the nation. The Prairie Pothole Region (PPR), characterized by glacial sediments and numerous wetlands, covers the northern and eastern portion of the Williston Basin. Sheridan County, Montana, lies within the PPR and has a documented history of brine contamination. Surface water and shallow groundwater in the PPR are saline and sulfate dominated while the deeper brines are much more saline and chloride dominated. A Contamination Index (CI), defined as the ratio of chloride concentration to specific conductance in a water sample, was developed by the Montana Bureau of Mines and Geology to delineate the magnitude of brine contamination in Sheridan County. Values > 0.035 indicate contamination. Recently, the U.S. Geological Survey completed a county level geographic information system (GIS)-based vulnerability assessment of brine contamination to aquatic resources in the PPR of the Williston Basin based on the age and density of oil wells, number of wetlands, and stream length per county. To validate and better define this assessment, a similar approach was applied in eastern Sheridan County at a greater level of detail (the 2.59 km2 Public Land Survey System section grid) and included surficial geology. Vulnerability assessment scores were calculated for the 780 modeled sections and these scores were divided into ten equal interval bins representing similar probabilities of contamination. Two surface water and two groundwater samples were collected from the section with the greatest acreage of Federal land in each bin. Nineteen of the forty water samples, and at least one water sample from seven of the ten selected sections, had CI values indicating contamination. Additionally, CI values generally increased with increasing vulnerability assessment score, with a stronger correlation for groundwater samples (R2 = 0.78) than surface water samples (R2 = 0.53).

  18. Evaporation Rates of Brine on Mars

    Science.gov (United States)

    Sears, D. W. G.; Chittenden, J.; Moore, S. R.; Meier, A.; Kareev, M.; Farmer, C. B.

    2004-01-01

    While Mars is now largely a dry and barren place, recent data have indicated that water has flowed at specific locations within the last approx. 10(exp 6) y. This had led to a resurgence of interest in theoretical and experimental work aimed at understanding the behavior of water on Mars. There are several means whereby the stability of liquid water on Mars could be increased, one being the presence solutes that would depress the freezing point. Salt water on Earth is about 0.5M NaCl, but laboratory experiments suggest that martian salt water is quite different. We recently began a program of laboratory measurements of the stability of liquid water, ice and ice-dust mixtures under martian conditions and here report measurements of the evaporation rate of 0.25M brine.

  19. Geochemistry of Aluminum in High Temperature Brines

    Energy Technology Data Exchange (ETDEWEB)

    Benezeth, P.; Palmer, D.A.; Wesolowski, D.J.

    1999-05-18

    The objective ofthis research is to provide quantitative data on the equilibrium and thermodynamic properties of aluminum minerals required to model changes in permeability and brine chemistry associated with fluid/rock interactions in the recharge, reservoir, and discharge zones of active geothermal systems. This requires a precise knowledge of the thermodynamics and speciation of aluminum in aqueous brines, spanning the temperature and fluid composition rangesencountered in active systems. The empirical and semi-empirical treatments of the solubility/hydrolysis experimental results on single aluminum mineral phases form the basis for the ultimate investigation of the behavior of complex aluminosilicate minerals. The principal objective in FY 1998 was to complete the solubility measurements on boehmite (AIOOH) inNaC1 media( 1 .O and 5.0 molal ionic strength, IOO-250°C). However, additional measurements were also made on boehmite solubility in pure NaOH solutions in order to bolster the database for fitting in-house isopiestic data on this system. Preliminary kinetic Measurements of the dissolution/precipitation of boehmite was also carried out, although these were also not planned in the earlier objective. The 1999 objectives are to incorporate these treatments into existing codes used by the geothermal industry to predict the chemistry ofthe reservoirs; these calculations will be tested for reliability against our laboratory results and field observations. Moreover, based on the success of the experimental methods developed in this program, we intend to use our unique high temperature pH easurement capabilities to make kinetic and equilibrium studies of pH-dependent aluminosilicate transformation reactions and other pH-dependent heterogeneous reactions.

  20. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents experimentally based design parameters for Portland cement concretes with and without silica fume and fly ash...... in marine atmospheric and submersed South Scandinavian environment. The design parameters are based on sequential measurements of 86 chloride profiles taken over ten years from 13 different types of concrete. The design parameters provide the input for an analytical model for chloride profiles as function...

  1. Chloride stress corrosion cracking of Alloy 600 in boric acid solutions

    Energy Technology Data Exchange (ETDEWEB)

    Berge, Ph. [Electricite de France, 92 - Paris la Defense (France); Noel, D.; Gras, J.M.; Prieux, B. [Electricite de France, 77 - Moret-sur-Loing (France). Direction des Etudes et Recherches

    1997-10-01

    The high nickel austenitic alloys are generally considered to have good resistance to chloride stress corrosion cracking. In the standard boiling magnesium chloride solution tests, alloys with more than 40% nickel are immune. Nevertheless, more recent data show that cracking can occur in both Alloys 600 and 690 if the solution is acidified. In other low pH media, such as boric acid solution at 100 deg C, transgranular and intergranular cracking are observed in Alloy 600 in the presence of minor concentrations of sodium chloride (2g/I). In concentrated boric acid at higher temperatures (250 and 290 deg C), intergranular cracking also occurs, either when the chloride concentration is high, or at low chloride contents and high oxygen levels. The role of pH and a possible specific action of boric acid are discussed, together with the influence of electrochemical potential. (author) 21 refs.

  2. Lattice Boltzmann modeling of boiling heat transfer: The boiling curve and the effects of wettability

    OpenAIRE

    Li, Q; Kang, Q. J.; Francois, M. M.; He, Y. L.; Luo, K. H.

    2015-01-01

    A hybrid thermal lattice Boltzmann (LB) model is presented to simulate thermal multiphase flows with phase change based on an improved pseudopotential LB approach [Q. Li, K. H. Luo, and X. J. Li, Phys. Rev. E 87, 053301 (2013)]. The present model does not suffer from the spurious term caused by the forcing-term effect, which was encountered in some previous thermal LB models for liquid-vapor phase change. Using the model, the liquid-vapor boiling process is simulated. The boiling curve togeth...

  3. Bioleaching combined brine leaching of heavy metals from lead-zinc mine tailings: Transformations during the leaching process.

    Science.gov (United States)

    Ye, Maoyou; Yan, Pingfang; Sun, Shuiyu; Han, Dajian; Xiao, Xiao; Zheng, Li; Huang, Shaosong; Chen, Yun; Zhuang, Shengwei

    2017-02-01

    During the process of bioleaching, lead (Pb) recovery is low. This low recovery is caused by a problem with the bioleaching technique. This research investigated the bioleaching combination of bioleaching with brine leaching to remove heavy metals from lead-zinc mine tailings. The impact of different parameters were studied, including the effects of initial pH (1.5-3.0) and solid concentration (5-20%) for bioleaching, and the effects of sodium chloride (NaCl) concentration (10-200 g/L) and temperature (25 and 50 °C) for brine leaching. Complementary characterization experiments (Sequential extraction, X-ray diffractometer (XRD), scanning electronic microscope (SEM)) were also conducted to explore the transformation of tailings during the leaching process. The results showed that bioleaching efficiency was significantly influenced by initial pH and solid concentration. Approximately 85.45% of iron (Fe), 4.12% of Pb, and 97.85% of zinc (Zn) were recovered through bioleaching in optimum conditions. Increasing the brine concentration and temperature promoted lead recovery. Lead was recovered from the bioleaching residues at a rate of 94.70% at 25 °C and at a rate of 99.46% at 50 °C when the NaCl concentration was 150 g/L. The study showed that bioleaching significantly changed the speciation of heavy metals and the formation and surface morphology of tailings. The metals were mainly bound in stable fractions after bioleaching.

  4. Empirical formula for the refractive index of freezing brine

    DEFF Research Database (Denmark)

    Frisvad, Jeppe Revall

    2009-01-01

    The refractive index of freezing brine is important for example in order to estimate oceanic scattering as sea ice develops. Previously, no simple continuous expression was available for estimating the refractive index of brine at subzero temperatures. I show that extrapolation of the empirical...... formula for the refractive index of seawater by Quan and Fry [Appl. Opt. 34(18), 3477-3480 (1995)] provides a good fit to the refractive index of freezing brine for temperatures above -24 degrees celsius and salinities below 180 parts per thousand....

  5. A review on boiling heat transfer enhancement with nanofluids.

    Science.gov (United States)

    Barber, Jacqueline; Brutin, David; Tadrist, Lounes

    2011-04-04

    There has been increasing interest of late in nanofluid boiling and its use in heat transfer enhancement. This article covers recent advances in the last decade by researchers in both pool boiling and convective boiling applications, with nanofluids as the working fluid. The available data in the literature is reviewed in terms of enhancements, and degradations in the nucleate boiling heat transfer and critical heat flux. Conflicting data have been presented in the literature on the effect that nanofluids have on the boiling heat-transfer coefficient; however, almost all researchers have noted an enhancement in the critical heat flux during nanofluid boiling. Several researchers have observed nanoparticle deposition at the heater surface, which they have related back to the critical heat flux enhancement.

  6. Microbial community of the deep-sea brine Lake Kryos seawater-brine interface is active below the chaotropicity limit of life as revealed by recovery of mRNA.

    Science.gov (United States)

    Yakimov, Michail M; La Cono, Violetta; Spada, Gina L; Bortoluzzi, Giovanni; Messina, Enzo; Smedile, Francesco; Arcadi, Erika; Borghini, Mireno; Ferrer, Manuel; Schmitt-Kopplin, Phillippe; Hertkorn, Norbert; Cray, Jonathan A; Hallsworth, John E; Golyshin, Peter N; Giuliano, Laura

    2015-02-01

    Within the complex of deep, hypersaline anoxic lakes (DHALs) of the Mediterranean Ridge, we identified a new, unexplored DHAL and named it 'Lake Kryos' after a nearby depression. This lake is filled with magnesium chloride (MgCl2 )-rich, athalassohaline brine (salinity > 470 practical salinity units), presumably formed by the dissolution of Messinian bischofite. Compared with the DHAL Discovery, it contains elevated concentrations of kosmotropic sodium and sulfate ions, which are capable of reducing the net chaotropicily of MgCl2 -rich solutions. The brine of Lake Kryos may therefore be biologically permissive at MgCl2 concentrations previously considered incompatible with life. We characterized the microbiology of the seawater-Kryos brine interface and managed to recover mRNA from the 2.27-3.03 M MgCl2 layer (equivalent to 0.747-0.631 water activity), thereby expanding the established chaotropicity window-for-life. The primary bacterial taxa present there were Kebrit Deep Bacteria 1 candidate division and DHAL-specific group of organisms, distantly related to Desulfohalobium. Two euryarchaeal candidate divisions, Mediterranean Sea Brine Lakes group 1 and halophilic cluster 1, accounted for > 85% of the rRNA-containing archaeal clones derived from the 2.27-3.03 M MgCl2 layer, but were minority community-members in the overlying interface-layers. These findings shed light on the plausibility of life in highly chaotropic environments, geochemical windows for microbial extremophiles, and have implications for habitability elsewhere in the Solar System.

  7. Subcooled pool boiling CHF in ethanol

    OpenAIRE

    Park, Jongdoc; Fukuda, Katsuya; Liu, Qiusheng

    2006-01-01

    Steady-state and transient critical heat fluxes (CHFs) were measured using a 1.0 mm diameter horizontal cylinder in a pool of highly wetting liquid, such as ethanol, due to steady and transient heat generation rate for wide range of subcoolings and pressures. Boiling CHF was assumed to happen based on a kind of hydrodynamic instability (HI) at CHF, and the model is supposed that the increase in vapor generation from the cylinder surface causes a limit of the steady-state vapor escape flow whe...

  8. Boiling heat transfer modern developments and advances

    CERN Document Server

    Lahey, Jr, RT

    2013-01-01

    This volume covers the modern developments in boiling heat transfer and two-phase flow, and is intended to provide industrial, government and academic researchers with state-of-the-art research findings in the area of multiphase flow and heat transfer technology. Special attention is given to technology transfer, indicating how recent significant results may be used for practical applications. The chapters give detailed technical material that will be useful to engineers and scientists who work in the field of multiphase flow and heat transfer. The authors of all chapters are members of the

  9. Pool boiling heat transfer performance of Newtonian nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Soltani, Saide; Etemad, Seyed Gholamreza [Isfahan University of Technology, Department of Chemical Engineering, Isfahan (Iran); Thibault, Jules [University of Ottawa, Department of Chemical and Biological Engineering, Ottawa, ON (Canada)

    2009-10-15

    Experimental measurements were carried out on the boiling heat transfer characteristics of {gamma}-Al{sub 2}O{sub 3}/water and SnO{sub 2}/water Newtonian nanofluids. Nanofluids are liquid suspensions containing nanoparticles with sizes smaller than 100 nm. In this research, suspensions with different concentrations of {gamma}-Al{sub 2}O{sub 3} and SnO{sub 2} nanoparticles in water were studied under nucleate pool boiling heat transfer conditions. Results show that nanofluids possess noticeably higher boiling heat transfer coefficients than the base fluid. The boiling heat transfer coefficients depend on the type and concentration of nanoparticles. (orig.)

  10. Investigation of Enhanced Boiling Heat Transfer from Porous Surfaces

    Institute of Scientific and Technical Information of China (English)

    LinZhiping; MaTongze; 等

    1994-01-01

    Experimental investigations of boiling heat transfer from porous surfaces at atmospheric pressure were performne.The porous surfaces are plain tubes coverd with metal screens.V-shaped groove tubes covered with screens,plain tubes sintered with screens.and V-shaped groove tubes sintered with screens,The experimental results show that sintering metal screens around spiral V-shaped groove tubes can greatly improve the boiling heat transfer,The boiling hystesis was observed in the experiment.This paper discusses the mechanism of the boiling heat transfer from those kinds of porous surfaces stated above.

  11. Boiling Experiment Facility for Heat Transfer Studies in Microgravity

    Science.gov (United States)

    Delombard, Richard; McQuillen, John; Chao, David

    2008-01-01

    Pool boiling in microgravity is an area of both scientific and practical interest. By conducting tests in microgravity, it is possible to assess the effect of buoyancy on the overall boiling process and assess the relative magnitude of effects with regards to other "forces" and phenomena such as Marangoni forces, liquid momentum forces, and microlayer evaporation. The Boiling eXperiment Facility is now being built for the Microgravity Science Glovebox that will use normal perfluorohexane as a test fluid to extend the range of test conditions to include longer test durations and less liquid subcooling. Two experiments, the Microheater Array Boiling Experiment and the Nucleate Pool Boiling eXperiment will use the Boiling eXperiment Facility. The objectives of these studies are to determine the differences in local boiling heat transfer mechanisms in microgravity and normal gravity from nucleate boiling, through critical heat flux and into the transition boiling regime and to examine the bubble nucleation, growth, departure and coalescence processes. Custom-designed heaters will be utilized to achieve these objectives.

  12. Projected effects of proposed chloride-control projects on shallow ground water; preliminary results for the Wichita River basin, Texas

    Science.gov (United States)

    Garza, Sergio

    1983-01-01

    The U.S. Army Corps of Engineers' plan to control the natural chloride pollution in the Wichita River basin includes the construction of Truscott Brine Lake on a tributary of the North Wichita River. In connection with the proposed brine lake, the U.S. Geological Survey was requested to: (1) Define the existing ground-water conditions in the shallow fresh-water system of the project area; and (2) project the post-construction effects of the proposed lake on the fresh-water aquifer, especially in relation to hydraulic-head changes but also with respect to possible changes in the chemical quality of the ground water.

  13. Modeling the morphogenesis of brine channels in sea ice

    CERN Document Server

    Kutschan, B; gemming, S

    2009-01-01

    Brine channels are formed in sea ice under certain constraints and represent a habitat of different microorganisms. The complex system depends on a number of various quantities as salinity, density, pH-value or temperature. Each quantity governs the process of brine channel formation. There exists a strong link between bulk salinity and the presence of brine drainage channels in growing ice with respect to both the horizontal and vertical planes. We develop a suitable phenomenological model for the formation of brine channels both referring to the Ginzburg-Landau-theory of phase transitions as well as to the chemical basis of morphogenesis according to Turing. It is possible to conclude from the critical wavenumber on the size of the structure and the critical parameters. The theoretically deduced transition rates have the same magnitude as the experimental values. The model creates channels of similar size as observed experimentally. An extension of the model towards channels with different sizes is possible...

  14. Development of the brine shrimp Artemia is accelerated during spaceflight

    Science.gov (United States)

    Spooner, B. S.; Metcalf, J.; DeBell, L.; Paulsen, A.; Noren, W.; Guikema, J. A.

    1994-01-01

    Developmentally arrested brine shrimp cysts have been reactivated during orbital spaceflight on two different Space Shuttle missions (STS-50 and STS-54), and their subsequent development has been compared with that of simultaneously reactivated ground controls. Flight and control brine shrimp do not significantly differ with respect to hatching rates or larval morphology at the scanning and transmission EM levels. A small percentage of the flight larvae had defective nauplier eye development, but the observation was not statistically significant. However, in three different experiments on two different flights, involving a total of 232 larvae that developed in space, a highly significant difference in degree of flight to control development was found. By as early as 2.25 days after reactivation of development, spaceflight brine shrimp were accelerated, by a full instar, over ground control brine shrimp. Although developing more rapidly, flight shrimp grew as long as control shrimp at each developmental instar or stage.

  15. Coiled Brine Recovery Assembly (CoBRA) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Coiled Brine Recovery Assembly (CoBRA) project will result in a proof-of-concept demonstration for a lightweight, compact, affordable, regenerable and disposable...

  16. Modal control of unstable boiling states in three-dimensional nonlinear pool-boiling

    NARCIS (Netherlands)

    Gils, van R.W.; Speetjens, M.F.M; Zwart, H.J.; Nijmeijer, H.

    2014-01-01

    Topic is feedback stabilisation of a nonlinear pool-boiling system in three spatial dimensions (3D). Regulation of its unstable (non-uniform) equilibria has great potential for application in micro-electronics cooling and thermal-management systems. Here, as a first step, stabilisation of such 3D eq

  17. Ion association in concentrated NaCl brines from ambient to supercritical conditions: results from classical molecular dynamics simulations

    Directory of Open Access Journals (Sweden)

    Collings Matthew D

    2002-11-01

    Full Text Available Highly concentrated NaCl brines are important geothermal fluids; chloride complexation of metals in such brines increases the solubility of minerals and plays a fundamental role in the genesis of hydrothermal ore deposits. There is experimental evidence that the molecular nature of the NaCl–water system changes over the pressure–temperature range of the Earth's crust. A transition of concentrated NaCl–H2O brines to a "hydrous molten salt" at high P and T has been argued to stabilize an aqueous fluid phase in the deep crust. In this work, we have done molecular dynamic simulations using classical potentials to determine the nature of concentrated (0.5–16 m NaCl–water mixtures under ambient (25°C, 1 bar, hydrothermal (325°C, 1 kbar and deep crustal (625°C, 15 kbar conditions. We used the well-established SPCE model for water together with the Smith and Dang Lennard-Jones potentials for the ions (J. Chem. Phys., 1994, 100, 3757. With increasing temperature at 1 kbar, the dielectric constant of water decreases to give extensive ion-association and the formation of polyatomic (NanClmn-m clusters in addition to simple NaCl ion pairs. Large polyatomic (NanClmn-m clusters resemble what would be expected in a hydrous NaCl melt in which water and NaCl were completely miscible. Although ion association decreases with pressure, temperatures of 625°C are not enough to overcome pressures of 15 kbar; consequently, there is still enhanced Na–Cl association in brines under deep crustal conditions.

  18. Survival of foodborne pathogens in natural cracked olive brines.

    Science.gov (United States)

    Medina, Eduardo; Romero-Gil, Verónica; Garrido-Fernández, Antonio; Arroyo-López, Francisco Noé

    2016-10-01

    This work reports the survival (challenge tests) of foodborne pathogen species (Escherichia coli, Staphylococcus aureus, Listeria monocytogenes, and Salmonella enterica) in Aloreña de Málaga table olive brines. The inhibitions were fit using a log-linear model with tail implemented in GInaFIT excel software. The olive brine had a considerable inhibitory effect on the pathogens. The residual (final) populations (Fp) after 24 h was below detection limit (olives for foodborne pathogenic microorganisms.

  19. The effects of brine disposal on a subtidal meiofauna community

    Science.gov (United States)

    Riera, Rodrigo; Tuya, Fernando; Sacramento, Alicia; Ramos, Eva; Rodríguez, Myriam; Monterroso, Óscar

    2011-07-01

    Desalination plants generate notable (>1,000 s m 3) quantities of hypersaline brine which potentially affect the biological communities in the receiving area. We assessed whether proximity to a brine discharge point located off Gran Canaria (Canary Islands, eastern Atlantic) altered patterns in the abundance and assemblage structure of subtidal, soft-bottom, meiofauna. Samples were collected twice (May 2008 and January 2009) at 0, 15 and 30 m away from the brine discharge point, corresponding to a change in salinity from 45 to 36. Proximity to the brine discharge point affected overall meiofaunal abundances: lowest abundances were observed at 0 m (64.55 ± 39.86 ind 10 cm -2, mean ± SD) than at 15 (210.49 ± 121.01 ind 10 cm -2) and 30 m (361.88 ± 102.64 ind 10 cm -2) away from the brine discharge point. This pattern was particularly notable for the most conspicuous meiofaunal groups: nematodes and copepods, and meiofaunal assemblage structure also differed with varying proximity to the brine discharge point. Although multivariate techniques identified changes in salinity as a relevant driver of patterns in meiofaunal assemblage structure with varying proximity to the brine outfall, a shift in particle size composition between May 2008 and January 2009 also contributed to explain differences in meiofaunal abundances and assemblage structure with varying proximity to the brine discharge point. Hence, meiofauna can be considered a suitable tool to monitor environmental impacts derived from the discharge of hypersaline effluents on subtidal, soft-bottom, assemblages if potential confounding drivers, i.e. here temporal changes in particle size composition, are accounted for to avoid possible confusing interpretations.

  20. Brine Shrimp Ecology In The Great Salt Lake, Utah

    OpenAIRE

    Wurtsbaugh, Wayne A.

    1995-01-01

    Hypersaline lakes are noted for their simple communities which facilitate understanding ecological interactions (Williams et al. 1990; Wurtsbaugh 1992; Jellison and Melack 1988). Nevertheless, we still cannot easily predict how environmental changes will effect the population dynamics in these lakes, at least in part because even these simple ecosystems may be more complex than we .realize. Many hypersaline lakes are dominated by the brine shrimp Artemia spp. The production of brine shrimp is...

  1. Trichloroethylene Volatilization Enhancement by the Addition of a Brine Solution

    Science.gov (United States)

    Irizarry, M. L.; Padilla, I. Y.

    2008-12-01

    Trichloroethylene (TCE) is one of the most widely detected organic contaminants at National Priority List (NPL) sites. In many sites, TCE is trapped as a dense non-aqueous phase liquid (DNAPL) in formations of low permeability, and serves as long-term source of contamination. Cost effective remediation technologies that can be applied to tight formations need to be developed. This study investigates the enhancement of TCE volatilization from unsaturated clayey soils by adding a NaCl brine solution. It is postulated that the overall effect of the brine solution causing structured water around soil particles, increased relative permeability, and increased fugacity into the vapor phase, is to enhance TCE volatilization. TCE removal through the soil vapor extraction (SVE) technique can then be enhanced. Preliminary experimental work involves the use of static and dynamic flux reactors, containing TCE, water and clay. NaCl brine solution is added at different concentrations to evaluate the effect on TCE concentrations and volatilization rates. In the static flux mode, vapor concentrations in the headspace of sealed reactors are measured after a two-day period. In the dynamic flux mode, air is swept through the headspace of the reactors and TCE vapor concentrations are measured over time. Plots relating static TCE vapor concentration to brine concentration are used to show the effect of brine concentrations on TCE fugacity. Temporal concentration distributions of TCE show the effect of brine on the rate of volatilization. Keywords: Trichloroethylene (TCE), Soil vapor extraction (SVE), clay

  2. Long-term monitoring of the Dead Sea level and brine physico-chemical parameters “from 1987 to 2008”

    Science.gov (United States)

    Khlaifat, Abdelaziz; Hogan, Michael; Phillips, Gary; Nawayseh, Khalid; Amira, Jamal; Talafeha, Emad

    2010-05-01

    The Dead Sea brine quality was assessed in order to provide scientific basis for researchers' needs. Four times a month, brine samples were collected from the Arab Potash Company (APC) point of intake and analyzed for physico-chemical parameters in the laboratory over 22 years, and Dead Sea surface temperature and level were measured during each sampling. The mean density values for the collected samples during the last 22 years ranged from 1.2040 g/cm 3 in 1992 to 1.2393 g/cm 3 in 2007, with an average value of 1.2376 g/cm 3. The brine salinity values ranged from 293.6 in 1992 to 339.3 g/l in 2008 with an average value of 337.73 g/l. The ionic dominance observed was Cl - > Mg ++ > Na + > Ca ++ > K +. The results showed that diluting the Dead Sea brine affects both magnesium and sodium chlorides significantly because of their high solubilities in fresh water and their large reserves.

  3. Development boiling to sprinkled tube bundle

    Directory of Open Access Journals (Sweden)

    Kracík Petr

    2016-01-01

    Full Text Available This paper presents results of a studied heat transfer coefficient at the surface of a sprinkled tube bundle where boiling occurs. Research in the area of sprinkled exchangers can be divided into two major parts. The first part is research on heat transfer and determination of the heat transfer coefficient at sprinkled tube bundles for various liquids, whether boiling or not. The second part is testing of sprinkle modes for various tube diameters, tube pitches and tube materials and determination of individual modes’ interface. All results published so far for water as the falling film liquid apply to one to three tubes for which the mentioned relations studied are determined in rigid laboratory conditions defined strictly in advance. The sprinkled tubes were not viewed from the operational perspective where there are more tubes and various modes may occur in different parts with various heat transfer values. The article focuses on these processes. The tube is located in a low-pressure chamber where vacuum is generated using an exhauster via ejector. The tube consists of smooth copper tubes of 12 mm diameter placed horizontally one above another.

  4. Unsteady heat transfer during subcooled film boiling

    Science.gov (United States)

    Yagov, V. V.; Zabirov, A. R.; Lexin, M. A.

    2015-11-01

    Cooling of high-temperature bodies in subcooled liquid is of importance for quenching technologies and also for understanding the processes initiating vapor explosion. An analysis of the available experimental information shows that the mechanisms governing heat transfer in these processes are interpreted ambiguously; a more clear-cut definition of the Leidenfrost temperature notion is required. The results of experimental observations (Hewitt, Kenning, and previous investigations performed by the authors of this article) allow us to draw a conclusion that there exists a special mode of intense heat transfer during film boil- ing of highly subcooled liquid. For revealing regularities and mechanisms governing intense transfer of energy in this process, specialists of Moscow Power Engineering Institute's (MPEI) Department of Engineering Thermal Physics conduct systematic works aimed at investigating the cooling of high-temperature balls made of different metals in water with a temperature ranging from 20 to 100°C. It has been determined that the field of temperatures that takes place in balls with a diameter of more than 30 mm in intense cooling modes loses its spherical symmetry. An approximate procedure for solving the inverse thermal conductivity problem for calculating the heat flux density on the ball surface is developed. During film boiling, in which the ball surface temperature is well above the critical level for water, and in which liquid cannot come in direct contact with the wall, the calculated heat fluxes reach 3-7 MW/m2.

  5. Development boiling to sprinkled tube bundle

    Science.gov (United States)

    Kracík, Petr; Pospíšil, Jiří

    2016-03-01

    This paper presents results of a studied heat transfer coefficient at the surface of a sprinkled tube bundle where boiling occurs. Research in the area of sprinkled exchangers can be divided into two major parts. The first part is research on heat transfer and determination of the heat transfer coefficient at sprinkled tube bundles for various liquids, whether boiling or not. The second part is testing of sprinkle modes for various tube diameters, tube pitches and tube materials and determination of individual modes' interface. All results published so far for water as the falling film liquid apply to one to three tubes for which the mentioned relations studied are determined in rigid laboratory conditions defined strictly in advance. The sprinkled tubes were not viewed from the operational perspective where there are more tubes and various modes may occur in different parts with various heat transfer values. The article focuses on these processes. The tube is located in a low-pressure chamber where vacuum is generated using an exhauster via ejector. The tube consists of smooth copper tubes of 12 mm diameter placed horizontally one above another.

  6. Zero boil-off system testing

    Science.gov (United States)

    Plachta, D. W.; Johnson, W. L.; Feller, J. R.

    2016-03-01

    Cryogenic propellants such as liquid hydrogen (LH2) and liquid oxygen (LO2) are a part of NASA's future space exploration plans due to their high specific impulse for rocket motors of upper stages. However, the low storage temperatures of LH2 and LO2 cause substantial boil-off losses for long duration missions. These losses can be eliminated by incorporating high performance cryocooler technology to intercept heat load to the propellant tanks and modulating the cryocooler temperature to control tank pressure. The technology being developed by NASA is the reverse turbo-Brayton cycle cryocooler and its integration to the propellant tank through a distributed cooling tubing network coupled to the tank wall. This configuration was recently tested at NASA Glenn Research Center in a vacuum chamber and cryoshroud that simulated the essential thermal aspects of low Earth orbit, its vacuum and temperature. This test series established that the active cooling system integrated with the propellant tank eliminated boil-off and robustly controlled tank pressure.

  7. Don Juan Pond, Antarctica: Near-surface CaCl2-brine feeding Earth's most saline lake and implications for Mars

    Science.gov (United States)

    Dickson, James L.; Head, James W.; Levy, Joseph S.; Marchant, David R.

    2013-01-01

    The discovery on Mars of recurring slope lineae (RSL), thought to represent seasonal brines, has sparked interest in analogous environments on Earth. We report on new studies of Don Juan Pond (DJP), which exists at the upper limit of ephemeral water in the McMurdo Dry Valleys (MDV) of Antarctica, and is adjacent to several steep-sloped water tracks, the closest analog for RSL. The source of DJP has been interpreted to be deep groundwater. We present time-lapse data and meteorological measurements that confirm deliquescence within the DJP watershed and show that this, together with small amounts of meltwater, are capable of generating brines that control summertime water levels. Groundwater input was not observed. In addition to providing an analog for RSL formation, CaCl2 brines and chloride deposits in basins may provide clues to the origin of ancient chloride deposits on Mars dating from the transition period from “warm/wet” to “cold/dry” climates. PMID:23378901

  8. Rewetting and Flow Film Boiling Along Hot Surface

    Institute of Scientific and Technical Information of China (English)

    王补宣Thermal Engineering Department; Tsinghua University; Beijing 100084; PRC; 彭晓峰

    1994-01-01

    The recent investigations on the rewettmg and film boiling of liquid flowing along a hot/heated surface are briefly reviewed and discussed.Some advanced theoretical analyses are conducted and new conclusions achieved.These investigations describe the fundamental characteristics of liquid flow boiling and further the complicated rewetting phenomena,and have resulted in considerable insight intothe mechanism.

  9. Thermal-hydraulic performance of convective boiling jet array impingement

    Science.gov (United States)

    Jenkins, R.; De Brún, C.; Kempers, R.; Lupoi, R.; Robinson, A. J.

    2016-09-01

    Jet impingement boiling is investigated with regard to heat transfer and pressure drop performance using a novel laser sintered 3D printed jet impingement manifold design. Water was the working fluid at atmospheric pressure with inlet subcooling of 7oC. The convective boiling performance of the impinging jet system was investigated for a flat copper target surface for 2700≤Re≤5400. The results indicate that the heat transfer performance of the impinging jet is independent of Reynolds number for fully developed boiling. Also, the investigation of nozzle to plate spacing shows that low spacing delays the onset of nucleate boiling causing a superheat overshoot that is not observed with larger gaps. However, no sensitivity to the gap spacing was measured once boiling was fully developed. The assessment of the pressure drop performance showed that the design effectively transfers heat with low pumping power requirements. In particular, owing to the insensitivity of the heat transfer to flow rate during fully developed boiling, the coefficient of performance of jet impingement boiling in the fully developed boiling regime deteriorates with increased flow rate due to the increase in pumping power flux.

  10. Low-Flow Film Boiling Heat Transfer on Vertical Surfaces

    DEFF Research Database (Denmark)

    Munthe Andersen, J. G.; Dix, G. E.; Leonard, J. E.

    1976-01-01

    The phenomenon of film boiling heat transfer for high wall temperatures has been investigated. Based on the assumption of laminar flow for the film, the continuity, momentum, and energy equations for the vapor film are solved and a Bromley-type analytical expression for the heat transfer...... length, an average film boiling heat transfer coefficient is obtained....

  11. Explosive Boiling at Very Low Heat Fluxes: A Microgravity Phenomenon

    Science.gov (United States)

    Hasan, M. M.; Lin, C. S.; Knoll, R. H.; Bentz, M. D.

    1993-01-01

    The paper presents experimental observations of explosive boiling from a large (relative to bubble sizes) flat heating surface at very low heat fluxes in microgravity. The explosive boiling is characterized as either a rapid growth of vapor mass over the entire heating surface due to the flashing of superheated liquid or a violent boiling spread following the appearance of single bubbles on the heating surface. Pool boiling data with saturated Freon 113 was obtained in the microgravity environment of the space shuttle. The unique features of the experimental results are the sustainability of high liquid superheat for long periods and the occurrence of explosive boiling at low heat fluxes (0.2 to 1.2 kW/sq m). For a heat flux of 1.0 kW/sq m a wall superheat of 17.9 degrees C was attained in ten minutes of heating. This was followed by an explosive boiling accompanied with a pressure spike and a violent bulk liquid motion. However, at this heat flux the vapor blanketing the heating surface could not be sustained. Stable nucleate boiling continued following the explosive boiling.

  12. Critical heat flux in flow boiling in microchannels

    CERN Document Server

    Saha, Sujoy Kumar

    2015-01-01

    This Brief concerns the important problem of critical heat flux in flow boiling in microchannels. A companion edition in the SpringerBrief Subseries on Thermal Engineering and Applied Science to “Heat Transfer and Pressure Drop in Flow Boiling in Microchannels,” by the same author team, this volume is idea for professionals, researchers, and graduate students concerned with electronic cooling.

  13. Boiling treatment of ABS and PS plastics for flotation separation.

    Science.gov (United States)

    Wang, Chong-qing; Wang, Hui; Wu, Bao-xin; Liu, Qun

    2014-07-01

    A new physical method, namely boiling treatment, was developed to aid flotation separation of acrylonitrile-butadiene-styrene (ABS) and polystyrene (PS) plastics. Boiling treatment was shown to be effective in producing a hydrophilic surface on ABS plastic. Fourier Transform Infrared analysis was conducted to investigate the mechanism of boiling treatment of ABS. Surface rearrangement of polymer may be responsible for surface change of boiling treated ABS, and the selective influence of boiling treatment on the floatability of boiling treated plastics may be attributed to the difference in the molecular mobility of polymer chains. The effects of flotation time, frother concentration and particle size on flotation behavior of simple plastic were investigated. Based on flotation behavior of simple plastic, flotation separation of boiling treatment ABS and PS with different particle sizes was achieved efficiently. The purity of ABS and PS was up to 99.78% and 95.80%, respectively; the recovery of ABS and PS was up to 95.81% and 99.82%, respectively. Boiling treatment promotes the industrial application of plastics flotation and facilitates plastic recycling.

  14. Influence of Pressure on Stable Film Boiling of Subcooled Liquid

    Science.gov (United States)

    Zabirov, A. R.; Yagov, V. V.; Kaban'kov, O. N.; Leksin, M. A.; Kanin, P. K.

    2016-11-01

    Film boiling of subcooled liquids is an integral part of the hardening process. Understanding of the mechanisms underlying film boiling is important for modeling processes in atomic power engineering and cryogenic technology. Stationary processes of film boiling of subcooled liquids under conditions of their free motion near cylindrical heaters, just as subcooled liquid turbulent flow past high-temperature surfaces, represent quite a different type of process. In cooling metal spheres heated to a high temperature by a subcooled water, a special regime of film boiling is observed (microbubble boiling) distinguished by high intensity of heat transfer. Such a regime has not been revealed up to now for nonaqueous liquids. The paper presents new experimental data on heat transfer regimes in cooling nickel spheres in subcooled isopropanol and perfluorohexane at pressures of up to 1 MPa. It has been established that stable film boiling is the main regime of heat transfer that accounts for the larger part of the total time of cooling. The regimes of highly intensive film boiling heat transfer were not observed in the entire range of operational parameters even in the case of extreme subcoolings of liquid below their saturation temperature (to 170 K). The intensity of heat transfer in stable film boiling increases noticeably with subcooling of a chilling liquid.

  15. Direct Numerical Simulation and Visualization of Subcooled Pool Boiling

    Directory of Open Access Journals (Sweden)

    Tomoaki Kunugi

    2014-01-01

    Full Text Available A direct numerical simulation of the boiling phenomena is one of the promising approaches in order to clarify their heat transfer characteristics and discuss the mechanism. During these decades, many DNS procedures have been developed according to the recent high performance computers and computational technologies. In this paper, the state of the art of direct numerical simulation of the pool boiling phenomena during mostly two decades is briefly summarized at first, and then the nonempirical boiling and condensation model proposed by the authors is introduced into the MARS (MultiInterface Advection and Reconstruction Solver developed by the authors. On the other hand, in order to clarify the boiling bubble behaviors under the subcooled conditions, the subcooled pool boiling experiments are also performed by using a high speed and high spatial resolution camera with a highly magnified telescope. Resulting from the numerical simulations of the subcooled pool boiling phenomena, the numerical results obtained by the MARS are validated by being compared to the experimental ones and the existing analytical solutions. The numerical results regarding the time evolution of the boiling bubble departure process under the subcooled conditions show a very good agreement with the experimental results. In conclusion, it can be said that the proposed nonempirical boiling and condensation model combined with the MARS has been validated.

  16. Genesis of underground brine along south coast of Laizhou Bay: hydrochemical characteristics

    Institute of Scientific and Technical Information of China (English)

    JIANG Xueyan; YU Zhigang; NING Jinsong; CHEN Hongtao; MI Tiezhu

    2006-01-01

    Hydrochemistry of underground brines along south coast of Laizhou Bay, Shandong, China has been analyzed. Brine samples were collected from 43 wells in this area. It was considered that the brines were originated from seawater. However, whether they were formed by seawater evaporation or seawater freezing was not fully sure. We created a simple method by plotting Na/Cl vs. seawater concentration factor (SCF) and Ca/Mg vs. SCF to determine the brine formation geochemically. Comparison of our results to previous seawater freezing and evaporation experiments indicated that the brines were formed by seawater evaporation. The ratios of HCO3/Cl of some low salinity brines in the study area were relatively higher, indicating that the brines may have mixed with other waters after the generation. The Br/Cl ratios of the brines decreased annually in the past 20 to 30 years of exploitation, indicating downward permeation of the brine from which bromine was extracted.

  17. Boiling in porous media; Ebullition en milieux poreux

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-11

    This conference day of the French society of thermal engineers was devoted to the analysis of heat transfers and fluid flows during boiling phenomena in porous media. This book of proceedings comprises 8 communications entitled: `boiling in porous medium: effect of natural convection in the liquid zone`; `numerical modeling of boiling in porous media using a `dual-fluid` approach: asymmetrical characteristic of the phenomenon`; `boiling during fluid flow in an induction heated porous column`; `cooling of corium fragment beds during a severe accident. State of the art and the SILFIDE experimental project`; `state of knowledge about the cooling of a particulates bed during a reactor accident`; `mass transfer analysis inside a concrete slab during fire resistance tests`; `heat transfers and boiling in porous media. Experimental analysis and modeling`; `concrete in accidental situation - influence of boundary conditions (thermal, hydric) - case studies`. (J.S.)

  18. Lithium Sulfuryl Chloride Battery.

    Science.gov (United States)

    Primary batteries , Electrochemistry, Ionic current, Electrolytes, Cathodes(Electrolytic cell), Anodes(Electrolytic cell), Thionyl chloride ...Phosphorus compounds, Electrical conductivity, Calibration, Solutions(Mixtures), Electrical resistance, Performance tests, Solvents, Lithium compounds

  19. High level disinfection of a home care device; to boil or not to boil?

    Science.gov (United States)

    Winthrop, K L; Homestead, N

    2012-03-01

    We developed a percutaneous electrical transducer for home therapy of chronic pain, a device that requires high level disinfection between uses. The utility of boiling water to provide high level disinfection was evaluated by inoculating transducer pads with potential skin pathogens (Staphylococcus aureus, Mycobacterium terrae, Pseudomonas aeruginosa, Candida albicans) and subjecting them to full immersion in water boiling at 4200 feet elevation (95 °C). Log10 reductions in colony-forming units (cfu) at 10 min were 7.1, >6.3 and >5.5 for S. aureus, P. aeruginosa and C. albicans, respectively, but only 4.6 for M. terrae. At 15 min the reductions had increased to 7.5, >6.8, >6.6 and >7.5 cfu, respectively.

  20. Hybrid modelling of a sugar boiling process

    CERN Document Server

    Lauret, Alfred Jean Philippe; Gatina, Jean Claude

    2012-01-01

    The first and maybe the most important step in designing a model-based predictive controller is to develop a model that is as accurate as possible and that is valid under a wide range of operating conditions. The sugar boiling process is a strongly nonlinear and nonstationary process. The main process nonlinearities are represented by the crystal growth rate. This paper addresses the development of the crystal growth rate model according to two approaches. The first approach is classical and consists of determining the parameters of the empirical expressions of the growth rate through the use of a nonlinear programming optimization technique. The second is a novel modeling strategy that combines an artificial neural network (ANN) as an approximator of the growth rate with prior knowledge represented by the mass balance of sucrose crystals. The first results show that the first type of model performs local fitting while the second offers a greater flexibility. The two models were developed with industrial data...

  1. The Physics of Boiling at Burnout

    Science.gov (United States)

    Theofanous, T. G.; Tu, J. P.; Dinh, T. N.; Salmassi, T.; Dinh, A. T.; Gasljevic, K.

    2000-01-01

    The basic elements of a new experimental approach for the investigation of burnout in pool boiling are presented. The approach consists of the combined use of ultrathin (nano-scale) heaters and high speed infrared imaging of the heater temperature pattern as a whole, in conjunction with highly detailed control and characterization of heater morphology at the nano and micron scales. It is shown that the burnout phenomenon can be resolved in both space and time. Ultrathin heaters capable of dissipating power levels, at steady-state, of over 1 MW/square m are demonstrated. A separation of scales is identified and it is used to transfer the focus of attention from the complexity of the two-phase mixing layer in the vicinity of the heater to a micron-scaled microlayer and nucleation and associated film-disruption processes within it.

  2. Redox states of underground brine system along the southern coast of the Laizhou Bay

    Institute of Scientific and Technical Information of China (English)

    JIANG Xueyan; YU Zhigang; NING Jinsong; CHEN Hongtao; MI Tiezhu

    2008-01-01

    Underground brine samples were collected along the southern coast of the Laizhou Bay,Shangdong,China in two field investigations in 2003.The brines are confined in the Quaternary sediment and underwent a series of geochemical changes.The redox states of these brines were assessed qualitatively based on the measurements of Eh and redox-sensitive species such as DO,NO NO3,Mn2+,Fe2+,SO2-4 in the brines.The redox condition of the underground brine is anoxic,and the redox reactions that controlled the redox potential of brines should be Fe (Ⅲ) reduction and sulfate reduction.

  3. Stability of polyvinyl alcohol-coated biochar nanoparticles in brine

    Science.gov (United States)

    Griffith, Christopher; Daigle, Hugh

    2017-01-01

    This paper reports on the dispersion stability of 150 nm polyvinyl alcohol coated biochar nanoparticles in brine water. Biochar is a renewable, carbon based material that is of significant interest for enhanced oil recovery operations primarily due to its wide ranging surface properties, low cost of synthesis, and low environmental toxicity. Nanoparticles used as stabilizing agents for foams (and emulsions) or in nanofluids have emerged as potential alternatives to surfactants for subsurface applications due to their improved stability at reservoir conditions. If, however, the particles are not properly designed, they are susceptible to aggregation because of the high salinity brines typical of oil and gas reservoirs. Attachment of polymers to the nanoparticle surface, through covalent bonds, provides steric stabilization, and is a necessary step. Our results show that as the graft density of polyvinyl alcohol increases, so too does the stability of nanoparticles in brine solutions. A maximum of 34 wt% of 50,000 Da polyvinyl alcohol was grafted to the particle surface, and the size of the particles was reduced from 3500 nm (no coating) to 350 nm in brine. After 24 h, the particles had a size of 500 nm, and after 48 h completely aggregated. 100,000 Da PVA coated at 24 wt% on the biochar particles were stable in brine for over 1 month with no change in mean particle size of 330 nm.

  4. Searching for brine on Mars using Raman spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, E.

    2016-07-01

    In the last few years, water ice and perchlorate salts capable of melting this ice and producing liquid solutions have been discovered at the surface and shallow subsurface of Mars. In addition to via melting of ice, perchlorate salts may also form liquid solutions by absorbing water vapor when the relative humidity is above a certain threshold in a process known as deliquescence. Formed either by melting or deliquescence, liquid solutions (brine) are the most likely way of liquid water activity on the Martian surface and in the shallow subsurface and are therefore important to understand the habitability of Mars. Using Raman spectroscopy, we provide reference spectra of various mixing states of liquid water, water ice and calcium perchlorate, all of which can occur during brine formation. We focus on the perchlorate symmetric stretching band and the O-H stretching vibrational band to distinguish brine from crystalline salt and water ice. We show that perchlorate brines can be identified by analyzing the peaks and their widths in the decomposed Raman spectra of the investigated samples. This serves as an important reference for future in-situ Raman spectrometers on Mars, such as those on the ExoMars and Mars 2020 rovers and can aid in the detection of brine formation on Mars. (Author)

  5. Effects of a brine discharge over soft bottom Polychaeta assemblage

    Energy Technology Data Exchange (ETDEWEB)

    Pilar-Ruso, Yoana del [Dpto. de Ciencias del Mar y Biologia Aplicada, Universidad de Alicante, Campus de San Vicente del Raspeig, Ap. 99, E-03080, Alicante (Spain)], E-mail: yoana.delpilar@ua.es; Ossa-Carretero, Jose Antonio de la; Gimenez-Casalduero, Francisca; Sanchez-Lizaso, Jose Luis [Dpto. de Ciencias del Mar y Biologia Aplicada, Universidad de Alicante, Campus de San Vicente del Raspeig, Ap. 99, E-03080, Alicante (Spain)

    2008-11-15

    Desalination is a growing activity that has introduced a new impact, brine discharge, which may affect benthic communities. Although the role of polychaetes as indicators to assess organic pollution is well known, their tolerance to salinity changes has not been examined to such a great extent. The aim of this study was to examine the effect of brine discharge over soft bottom polychaete assemblage along the Alicante coast (Southeast Spain) over a two year period. Changes in the polychaete assemblage was analysed using univariate and multivariate techniques. We compared a transect in front of the discharge with two controls. At each transect we sampled at three depths (4, 10 and 15 m) during winter and summer. We have observed different sensitivity of polychaete families to brine discharges, Ampharetidae being the most sensitive, followed by Nephtyidae and Spionidae. Syllidae and Capitellidae showed some resistance initially, while Paraonidae proved to be a tolerant family. - The Polychaete assemblage is affected by the brine discharge of the Alicante desalination plant and we detect different sensitivity levels in polychaete families to brine impact.

  6. Solubility of some alkali and alkaline earth chlorides in water at moderate temperatures

    Science.gov (United States)

    Clynne, M.A.; Potter, R.W.

    1979-01-01

    Solubilities for the binary systems, salt-H2O, of the chlorides of lithium, rubidium, cesium, magnesium, calcium, strontium, and barium from near 0??C to the saturated boiling point are reported. The experimental data and coefficients of an equation for a smoothed curve describing each system are listed in the tables. The data are improvements on those previously reported in the literature, having a precision on the average of ??0.09%.

  7. Chemistry and Spectroscopy of Frozen Chloride Salts on Icy Bodies

    Science.gov (United States)

    Johnson, Paul; Thomas, Elena C.; Hodyss, Robert; Vu, Tuan; Choukroun, Mathieu

    2016-10-01

    Currently, our understanding of the chemical composition of Europa's surface is our best means of inferring constraints on the subsurface ocean composition and its subsequent habitability. The bulk of our knowledge of Europa surface chemistry can be traced to near infrared spectra recorded by the Near Infrared Mapping Spectrometer on the Galileo spacecraft. However, the usefulness of this and other remote sensing data is limited by the availability of spectral libraries of candidate materials under relevant conditions (temperature, thermal/radiation history, etc.). Chloride salts are expected to exist on the surface of Europa, and other icy bodies, based on geochemical predictions of the ocean composition. In order to help improve our understanding of Europa's surface composition, we have conducted a study of frozen chloride-salt brines prepared under simulated Europa surface conditions (vacuum, temperature, and UV irradiation) using both near IR and Raman spectroscopies. Specifically, Raman spectroscopy was used to determine the hydration states of various chloride salts as a function of temperature. Near IR spectroscopy of identically prepared samples was used to provide reference reflectance spectra of the identified hydrated salts. Our results indicate that at temperatures ranging from 80 K to 233 K, hydrohalite is formed from the freezing of NaCl brines, while the freezing of KCl solutions does not form KCl hydrates. In addition, the freezing of MgCl2 solutions forms a stable hexahydrate, and the freezing of CaCl2 solutions forms a hexahydrate, a tetrahydrate, and a dihydrate. Dehydration of the salts was observed as temperatures were increased, leading to a succession of hydration states in the case of CaCl2.

  8. Transition boiling heat transfer and the film transition regime

    Science.gov (United States)

    Ramilison, J. M.; Lienhard, J. H.

    1987-01-01

    The Berenson (1960) flat-plate transition-boiling experiment has been recreated with a reduced thermal resistance in the heater, and an improved access to those portions of the transition boiling regime that have a steep negative slope. Tests have been made in Freon-113, acetone, benzene, and n-pentane boiling on horizontal flat copper heaters that have been mirror-polished, 'roughened', or teflon-coated. The resulting data reproduce and clarify certain features observed by Berenson: the modest surface finish dependence of boiling burnout, and the influence of surface chemistry on both the minimum heat flux and the mode of transition boiling, for example. A rational scheme of correlation yields a prediction of the heat flux in what Witte and Lienhard (1982) previously identified as the 'film-transition boiling' region. It is also shown how to calculate the heat flux at the boundary between the pure-film, and the film-transition, boiling regimes, as a function of the advancing contact angle.

  9. Research progresses and future directions on pool boiling heat transfer

    Directory of Open Access Journals (Sweden)

    M. Kumar

    2015-12-01

    Full Text Available This paper reviews the previous work carried on pool boiling heat transfer during heating of various liquids and commodities categorized as refrigerants and dielectric fluids, pure liquids, nanofluids, hydrocarbons and additive mixtures, as well as natural and synthetic colloidal solutions. Nucleate pool boiling is an efficient and effective method of boiling because high heat fluxes are possible with moderate temperature differences. It is characterized by the growth of bubbles on a heated surface. It occurs during boiling of liquids for excess temperature ranging from 5 to 30 °C in various processes related to high vaporization of liquid for specific purposes like sugarcane juice heating for jaggery making, milk heating for khoa making, steam generation, cooling of electronic equipments, refrigeration and etcetera. In this review paper, pool boiling method during heating of liquids for specific purpose is depicted. It is inferred that enhancement in pool boiling heat transfer is a challenging and complex task. Also, recent research and use of various correlations for natural convection pool boiling is reviewed.

  10. The evolution of the 87Sr/86Sr in the Dead Sea brine: from the Sedom lagoon to Sahara dusts

    Science.gov (United States)

    Stein, Mordechai

    2016-04-01

    The history of water-bodies in the Dead Sea brines commenced with the intrusion of the Sedom lagoon, possibly in the late Neogene and continued with the development of hypersaline and freshwater lakes (e.g. the modern Dead Sea and Sea of Galilee). 87Sr/86Sr ratios in these water-bodies decreased over the past ~ 5-6 Ma from 0.7087-0.7084 in salts deposited in the Sedom lagoon to ~ 0.7080 in modern Dead Sea brine. The 87Sr/86Sr ratios in the salts deposited from Sedom lagoon are significantly lower than those of the contemporaneous late Miocene seawater (~0.709). This difference was attributed to modification of the 87Sr/86Sr ratio in the Sedom lagoon solution by influx of Ca-chloride brines. The brines, in turn were formed by dolomitization of marine limestones of the DSR Cretaceous wall rocks (87Sr/86Sr ~ 0.7075) by the ingressing evaporated seawaters (Stein et al., 2000). After the disconnection of the Sedom lagoon from the open sea freshwater filled the lakes that occupied the Dead Sea basin. The freshwater influx modified the strontium isotope and chemical composition of the brine and provided bicarbonate and sulfate to the lake that led the precipitation of primary aragonite and gypsum. Freshwater that currently enter the lake are characterize by 87Sr/86Sr ~ 0.7081, significantly higher than the Cretaceous carbonates. Settled dust that deposits on the Judea Mountains is composed of calcite and quartz grains and is characterized by 87Sr/86Sr ratios ~ 0.7084. It appears that significant amounts of the strontium that entered the lakes with the freshwater originated from dissolution of the dust calcites. Large amounts of dust were transported from the Sahara desert to the Dead Sea watershed during glacial periods when the Sahara was dry and sea-level was low. The source of the detrital calcites however, is not known. They could be derived from dry paleo-lakes in the Sahara that were previously filled by waters that retained the required strontium isotope

  11. Actinide (III) solubility in WIPP Brine: data summary and recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Borkowski, Marian; Lucchini, Jean-Francois; Richmann, Michael K.; Reed, Donald T.

    2009-09-01

    The solubility of actinides in the +3 oxidation state is an important input into the Waste Isolation Pilot Plant (WIPP) performance assessment (PA) models that calculate potential actinide release from the WIPP repository. In this context, the solubility of neodymium(III) was determined as a function of pH, carbonate concentration, and WIPP brine composition. Additionally, we conducted a literature review on the solubility of +3 actinides under WIPP-related conditions. Neodymium(III) was used as a redox-invariant analog for the +3 oxidation state of americium and plutonium, which is the oxidation state that accounts for over 90% of the potential release from the WIPP through the dissolved brine release (DBR) mechanism, based on current WIPP performance assessment assumptions. These solubility data extend past studies to brine compositions that are more WIPP-relevant and cover a broader range of experimental conditions than past studies.

  12. Assessment of Brine Management for Geologic Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Breunig, Hanna M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Birkholzer, Jens T. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Borgia, Andrea [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Price, Phillip N. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Oldenburg, Curtis M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; McKone, Thomas E. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

    2013-06-13

    Geologic carbon sequestration (GCS) is the injection of carbon dioxide (CO2), typically captured from stationary emission sources, into deep geologic formations to prevent its entry into the atmosphere. Active pilot facilities run by regional United States (US) carbon sequestration partnerships inject on the order of one million metric tonnes (mt) CO2 annually while the US electric power sector emits over 2000 million mt-CO2 annually. GCS is likely to play an increasing role in US carbon mitigation initiatives, but scaling up GCS poses several challenges. Injecting CO2 into sedimentary basins raises fluid pressure in the pore space, which is typically already occupied by naturally occurring, or native, brine. The resulting elevated pore pressures increase the likelihood of induced seismicity, of brine or CO2 escaping into potable groundwater resources, and of CO2 escaping into the atmosphere. Brine extraction is one method for pressure management, in which brine in the injection formation is brought to the surface through extraction wells. Removal of the brine makes room for the CO2 and decreases pressurization. Although the technology required for brine extraction is mature, this form of pressure management will only be applicable if there are cost-­effective and sustainable methods of disposing of the extracted brine. Brine extraction, treatment, and disposal may increase the already substantial capital, energy, and water demands of Carbon dioxide Capture and Sequestration (CCS). But, regionally specific brine management strategies may be able to treat the extracted water as a source of revenue, energy, and water to subsidize CCS costs, while minimizing environmental impacts. By this approach, value from the extracted water would be recovered before disposing of any resulting byproducts. Until a price is placed on carbon, we expect that utilities and other CO2 sources will be

  13. Magnesium salts as compounds of the preparation of magnesium oxide from Tunisian natural brines

    Directory of Open Access Journals (Sweden)

    Behij Souheil

    2013-01-01

    Full Text Available Magnesium oxide is one of the most important magnesium compounds used in industry. The production of MgO is often done from calcined magnesium carbonate or from natural magnesium saline solutions (sea water and brines. In the case of these solutions, magnesium oxide is precipitated after the addition of a strong base (eg. Ammonia. Magnesium hydroxide is calcined after its separation from the excess resulting from the strong base through filtration. Thus, magnesia qualities may differ depending on several physical parameters and particularly on the nature of the compound. Consequently, two different compounds were selected: magnesium chloride and magnesium sulphate which can be recovered from Tunisian natural brines. Three physical factors were considered: calcination temperatures, precipitation temperatures and calcination time of Mg(OH2. The decomposition of Mg(OH2 was investigated by DTA/TGA. Mass losses vary in the range (23.0%-29.9%. Starting decomposition temperatures are between 362°C and 385°C. The MgO produced from MgSO4 under 1000°C within 48 hours of calcination time and with 40°C as a reaction temperature for Mg(OH2 shows a good crystallinity and is of a cristallyte size of 86.3 nm and has a specific surface area equal to 16.87 m2g-1. Finally, morphological differences between MgO agglomerates at different temperatures were observed by SEM. Consequently, magnesium sulphate as precursor for preparing MgO is selected.

  14. Microbially mediated barite dissolution in anoxic brines

    Science.gov (United States)

    Ouyang, Bingjie; Akob, Denise M.; Dunlap, Darren S.; Renock, Devon

    2017-01-01

    Fluids injected into shale formations during hydraulic fracturing of black shale return with extraordinarily high total-dissolved-solids (TDS) and high concentrations of barium (Ba) and radium (Ra). Barite, BaSO4, has been implicated as a possible source of Ba as well as a problematic mineral scale that forms on internal well surfaces, often in close association with radiobarite, (Ba,Ra)SO4. The dissolution of barite by abiotic processes is well quantified. However, the identification of microbial communities in flowback and produced water necessitates the need to understand barite dissolution in the presence of bacteria. Therefore, we evaluated the rates and mechanisms of abiotic and microbially-mediated barite dissolution under anoxic and hypersaline conditions in the laboratory. Barite dissolution experiments were conducted with bacterial enrichment cultures established from produced water from Marcellus Shale wells located in northcentral Pennsylvania. These cultures were dominated by anaerobic halophilic bacteria from the genus Halanaerobium. Dissolved Ba was determined by ICP-OES and barite surfaces were investigated by SEM and AFM. Our results reveal that: 1) higher amounts of barium (up to ∼5 × ) are released from barite in the presence of Halanaerobium cultures compared to brine controls after 30 days of reaction, 2) etch pits that develop on the barite (001) surface in the presence of Halanaerobium exhibit a morphology that is distinct from those that form during control experiments without bacteria, 3) etch pits that develop in the presence of Halanaerobium exhibit a morphology that is similar to the morphology of etch pits formed in the presence of strong organic chelators, EDTA and DTPA, and 4) experiments using dialysis membranes to separate barite from bacteria suggest that direct contact between the two is not required in order to promote dissolution. These results suggest that Halanaerobium increase the rate of barite dissolution in anoxic and

  15. Modeling of Heat Exchange with Developed Nucleate Boiling on Tenons

    Directory of Open Access Journals (Sweden)

    A. V. Оvsiannik

    2007-01-01

    Full Text Available The paper proposes a thermal and physical model for heat exchange processes with developed nucleate boiling on the developed surfaces (tenons with various contours of heat transfer surface. Dependences for calculating convective heat exchange factor have been obtained on the basis of modeling representation. Investigations have shown that an intensity of convective heat exchange does not depend on tenon profile when boiling takes place on the tenons. The intensity is determined by operating conditions, thermal and physical properties of liquid, internal characteristics of boiling processes and geometrical characteristics of a tenon.

  16. Boiling Heat Transfer on Porous Surfaces with Vapor Channels

    Institute of Scientific and Technical Information of China (English)

    吴伟; 杜建华; 王补宣

    2002-01-01

    Boiling heat transfer on porous coated surfaces with vapor channels was investigated experimentally to determine the effects of the size and density of the vapor channels on the boiling heat transfer. Observations showed that bubbles escaping from the channels enhanced the heat transfer. Three regimes were identified: liquid flooding, bubbles in the channel and the bottom drying out region. The maximum heat transfer occurred for an optimum vapor channel density and the boiling heat transfer performance was increased if the channels were open to the bottom of the porous coating.

  17. Experimental study on the explosive boiling in saturated liquid nitrogen

    Institute of Scientific and Technical Information of China (English)

    DONG Zhaoyi; HUAI Xiulan; LIU Dengying

    2005-01-01

    Studies on the heat-transfer characteristics of liquid nitrogen (LN2) have received increasing attention. When there is a transient high heatflux input to the LN2, explosive boiling may take place. In this paper, using the high-power short-duration pulsed laser heating method and the high-speed photography technology, the experimental result of explosive boiling in saturated LN2 is illustrated; and the two exclusive characteristics of explosive boiling in LN2: changeover time and the relative long-time adherence of the bubble cluster to the surface, are investigated.

  18. Subcooled boiling of nano-particle suspensions on Pt wires

    Institute of Scientific and Technical Information of China (English)

    LI Chunhui; WANG Buxuan; PENG Xiaofeng

    2004-01-01

    An experimental investigation is conducted to explore the subcooled boiling characteristics of nano-particle suspensions on Pt wires. Some phenomena are observed for the boiling of water-SiO2 nano-particle suspensions on Pt wires. The experiments show that there exist not any evident differences for boiling of pure water and of nano-particle suspensions at high heat fluxes. However, bubble overlap phenomenon can be easily found for nano-particle suspensions at low heat fluxes, which probably results from the increase of the attracter force between bubbles and of the bubble mass.

  19. Bubble Coalescence Heat Transfer During Subcooled Nucleate Pool Boiling

    Institute of Scientific and Technical Information of China (English)

    Abdoulaye Coulibaly; LIN Xipeng; Bi Jingliang; David M Christopher

    2012-01-01

    Bubble coalescence during subcooled nucleate pool boiling was investigated experimentally using constant wall temperature boundary conditions while the wall heat flux was measured at a various locations to understand the effects of coalescence on the heat transfer. The observations showed that the coalesced bubble moved and oscillated on the heater surface with significant heat transfer variations prior to departure. Some observations also showed coalescence with no increase in the heat transfer rate. The heat flux for boiling with coalescence fluctuated much more than for single bubble boiling due to the vaporization of the liquid layer trapped between the bubbles.

  20. Spectroscopy and detectability of liquid brines on mars

    Science.gov (United States)

    Massé, M.; Beck, P.; Schmitt, B.; Pommerol, A.; McEwen, A.; Chevrier, V.; Brissaud, O.; Séjourné, A.

    2014-03-01

    Recent geomorphological observations as well as chemical and thermodynamic studies demonstrate that liquid water should be stable today on the Martian surface at some times of the day. In Martian conditions, brines would be particularly more stable than pure water because salts can depress the freezing point and lower the evaporation rate of water. Despite this evidence, no clear spectral signature of liquid has been observed so far by the hyperspectral imaging spectrometers OMEGA and CRISM. However, past spectral analysis lacks a good characterization of brines' spectral signatures. This study thus aims to determine how liquid brines can be detected on Mars by spectroscopy. In this way, laboratory experiments were performed for reproducing hydration and dehydration cycles of various brines while measuring their spectral signatures. The resulting spectra first reveal a very similar spectral evolution for the various brine types and pure water, with the main difference observed at the end of the dehydration with the crystallization of various hydrated minerals from brines. The main characteristic of this spectral behavior is an important decoupling between the evolution of albedo and hydration bands depths. During most of the wetting/drying processes, spectra usually display a low albedo associated with shallow water absorption band depths. Strong water absorption band depth and high albedo are respectively only observed when the surface is very wet and when the surface is very dry. These experiments can thus explain why the currently active Martian features attributed to the action of a liquid are only associated with low albedo and very weak spectral signatures. Hydration experiments also reveal that deliquescence occurs easily even at low temperature and moderate soil water vapor pressure and could thus cause seasonal darkening on Mars. These experiments demonstrate that the absence of water absorptions in CRISM in the middle afternoon does not rule out water

  1. Assessing Radium Activity in Shale Gas Produced Brine

    Science.gov (United States)

    Fan, W.; Hayes, K. F.; Ellis, B. R.

    2015-12-01

    The high volumes and salinity associated with shale gas produced water can make finding suitable storage or disposal options a challenge, especially when deep well brine disposal or recycling for additional well completions is not an option. In such cases, recovery of commodity salts from the high total dissolved solids (TDS) of the brine wastewater may be desirable, yet the elevated concentrations of the naturally occurring radionuclides such as Ra-226 and Ra-228 in produced waters (sometimes substantially greater than the EPA limit of 5 pCi/L) may concentrate during these steps and limit salt recovery options. Therefore, assessing the potential presence of these Ra radionuclides in produced water from shale gas reservoir properties is desirable. In this study, we seek to link U and Th content within a given shale reservoir to the expected Ra content of produced brine by accounting for secular equilibrium within the rock and subsequent release to Ra to native brines. Produced brine from a series of Antrim shale wells and flowback from a single Utica-Collingwood shale well in Michigan were sampled and analyzed via ICP-MS to measure Ra content. Gamma spectroscopy was used to verify the robustness of this new Ra analytical method. Ra concentrations were observed to be up to an order of magnitude higher in the Antrim flowback water samples compared to those collected from the Utica-Collingwood well. The higher Ra content in Antrim produced brines correlates well with higher U content in the Antrim (19 ppm) relative to the Utica-Collingwood (3.5 ppm). We also observed an increase in Ra activity with increasing TDS in the Antrim samples. This Ra-TDS relationship demonstrates the influence of competing divalent cations in controlling Ra mobility in these clay-rich reservoirs. In addition, we will present a survey of geochemical data from other shale gas plays in the U.S. correlating shale U, Th content with produced brine Ra content. A goal of this study is to develop a

  2. Ice Control with Brine Spread with Nozzles on Highways

    DEFF Research Database (Denmark)

    Bolet, Lars; Fonnesbech, Jens Kristian

    2010-01-01

    . The improvements gained by the county of Funen were mainly due to the use of technologies (brine spreading with nozzles) giving a more precise spread pattern than the traditional gritting of pre-wetted salt. The spread pattern for every spreader, tested in The County of Funen, has been meassured 3 hours after...... spreading on a highway with traffic. A total of 800 spots were measured for residual salt for every spreader. The measurements and the spread pattern for brine spreading with nozzles were so precisely, that we learned: “When there is moisture, water or ice on the road, we need to take into account...

  3. Optimization of Quick-boiling Process for Lotus Root Slices%藕片水焯工艺优化

    Institute of Scientific and Technical Information of China (English)

    计红芳; 张令文; 杨铭铎; 李光磊; 蔡振林

    2011-01-01

    Lotus root slices was quick boiled in four different media such as water,acetic acid,sodium chloride and sodium bicarbonate solution and as a result,acetic acid was identified as the best medium through comprehensive considering VC content and sensory score of quick-boiled lotus root slices as well as dry matter dissolution rate.Further,on the basis of one-factor-at-a-time experiments,Box-Behnken design combined with response surface methodology was used to optimize process conditions for the quick boiling of lotus root slices in acetic acid.The results indicated that the optimal quick boiling conditions were acetic acid concentration of 0.35%,temperature of 68.4 ℃ and quick-boiling time of 2.4 min.After quick boiling under the optimal process conditions,the content of vitamin C in lotus root slices was 30.185 mg/100 g fresh weight,and better eating quality was also achieved.The results of variance analysis showed that acetic acid concentration,quick-boiling temperature and quick-boiling time had significant effects on the content of vitamin C in quick-boiled lotus root slices(P0.01).Moreover,the cross-interactions between acetic acid concentration and temperature and between temperature and quick-boiling time also revealed a significant effect on the content of vitamin C in lotus root slices(P0.05).%以新鲜莲藕为试验材料,对水、乙酸溶液、食盐溶液和碳酸氢钠溶液等4种水焯介质进行探讨;通过单因素试验和Box-Behnken设计及响应面分析法,对藕片水焯的最佳工艺条件进行研究。结果表明:乙酸可作为藕片的水焯介质;藕片水焯的最佳工艺条件为乙酸体积分数0.35%、温度68.4℃、时间2.4min,在该条件下藕片中VC含量为30.185mg/100g,干物质溶出率为5.384%,藕片食用品质可达到较高水平。响应面方差分析结果显示,乙酸体积分数、温度和水焯时间对水焯藕片VC含量有显著影响(P〈0.01),乙酸体积分数和温度、温度和

  4. The influence of closed brine pockets and permeable brine channels on the thermo-elastic properties of saline ice.

    Science.gov (United States)

    Marchenko, Aleksey; Lishman, Ben

    2017-02-13

    A model of the thermo-elastic behaviour of saline ice is formulated, and model solutions describing thermo-elastic waves (TEW) propagating into a half-space of the ice are investigated. The model is based on a proposal that saline ice is a matrix, which encompasses both closed brine pockets and permeable channels filled with brine. Experiments on the thermal expansion of saline ice samples, and on TEW in saline ice, have been performed in the cold laboratories of the University Centre in Svalbard and in University College London. The experimental data are compared with theoretical conclusions. The experimental data support our hypothesis that the brine in saline ice is divided between closed pockets and open, permeable channels.This article is part of the themed issue 'Microdynamics of ice'.

  5. An evaporated seawater origin for the ore-forming brines in unconformity-related uranium deposits (Athabasca Basin, Canada): Cl/Br and δ 37Cl analysis of fluid inclusions

    Science.gov (United States)

    Richard, Antonin; Banks, David A.; Mercadier, Julien; Boiron, Marie-Christine; Cuney, Michel; Cathelineau, Michel

    2011-05-01

    Analyses of halogen concentration and stable chlorine isotope composition of fluid inclusions from hydrothermal quartz and carbonate veins spatially and temporally associated with giant unconformity-related uranium deposits from the Paleoproterozoic Athabasca Basin (Canada) were performed in order to determine the origin of chloride in the ore-forming brines. Microthermometric analyses show that samples contain variable amounts of a NaCl-rich brine (Cl concentration between 120,000 and 180,000 ppm) and a CaCl 2-rich brine (Cl concentration between 160,000 and 220,000 ppm). Molar Cl/Br ratios of fluid inclusion leachates range from ˜100 to ˜900, with most values between 150 and 350. Cl/Br ratios below 650 (seawater value) indicate that the high salinities were acquired by evaporation of seawater. Most δ 37Cl values are between -0.6‰ and 0‰ (seawater value) which is also compatible with a common evaporated seawater origin for both NaCl- and CaCl 2-rich brines. Slight discrepancies between the Cl concentration, Cl/Br, δ 37Cl data and seawater evaporation trends, indicate that the evaporated seawater underwent secondary minor modification of its composition by: (i) mixing with a minor amount of halite-dissolution brine or re-equilibration with halite during burial; (ii) dilution in a maximum of 30% of connate and/or formation waters during its migration towards the base of the Athabasca sandstones; (iii) leaching of chloride from biotites within basement rocks and (iv) water loss by hydration reactions in alteration haloes linked to uranium deposition. The chloride in uranium ore-forming brines of the Athabasca Basin has an unambiguous dominantly marine origin and has required large-scale seawater evaporation and evaporite deposition. Although the direct evidence for evaporative environments in the Athabasca Basin are lacking due to the erosion of ˜80% of the sedimentary pile, Cl/Br ratios and δ 37Cl values of brines have behaved conservatively at the basin

  6. Visualization of boiling flow structure in a natural circulation boiling loop

    Energy Technology Data Exchange (ETDEWEB)

    Karmakar, Arnab; Paruya, Swapan, E-mail: swapanparuya@gmail.com

    2015-04-15

    Highlights: • Vapor–liquid jet flows in natural circulation boiling loop. • Flow patterns and their transitions during geysering instability in the loop. • Evaluation of the efficiency of the needle probe in detecting the vapor–liquid and boiling flow structure. - Abstract: The present study reports vapor–liquid jet flows, flow patterns and their transitions during geysering instability in a natural circulation boiling loop under varied inlet subcooling ΔT{sub sub} (30–50 °C) and heater power Q (4–5 kW). Video imaging, voltage measurement using impedance needle probe, measurement of local pressure and loop flow rate have been carried out in this study. Power spectra of the voltage, the pressure and the flow rate reveal that at a high ΔT{sub sub} the jet flows have long period (21.36–86.95 s) and they are very irregular with a number of harmonics. The period decreases and becomes regular with a decrease of ΔT{sub sub}. The periods of the jet flows at ΔT{sub sub} = 30–50 °C and Q = 4 kW are in close agreement with those obtained from the video imaging. The probe was found to be more efficient than the pressure sensor in detecting the jet flows within an uncertainty of 9.5% and in detecting a variety of bubble classes. Both the imaging and the probe consistently identify the bubbly flow/vapor-mushrooms transition or the bubbly flow/slug flow transition on decreasing ΔT{sub sub} or on increasing Q.

  7. Self-Sustaining Thorium Boiling Water Reactors

    Directory of Open Access Journals (Sweden)

    Ehud Greenspan

    2012-10-01

    Full Text Available A thorium-fueled water-cooled reactor core design approach that features a radially uniform composition of fuel rods in stationary fuel assembly and is fuel-self-sustaining is described. This core design concept is similar to the Reduced moderation Boiling Water Reactor (RBWR proposed by Hitachi to fit within an ABWR pressure vessel, with the following exceptions: use of thorium instead of depleted uranium for the fertile fuel; elimination of the internal blanket; and elimination of absorbers from the axial reflectors, while increasing the length of the fissile zone. The preliminary analysis indicates that it is feasible to design such cores to be fuel-self-sustaining and to have a comfortably low peak linear heat generation rate when operating at the nominal ABWR power level of nearly 4000 MWth. However, the void reactivity feedback tends to be too negative, making it difficult to have sufficient shutdown reactivity margin at cold zero power condition. An addition of a small amount of plutonium from LWR used nuclear fuel was found effective in reducing the magnitude of the negative void reactivity effect and enables attaining adequate shutdown reactivity margin; it also flattens the axial power distribution. The resulting design concept offers an efficient incineration of the LWR generated plutonium in addition to effective utilization of thorium. Additional R&D is required in order to arrive at a reliable practical and safe design.

  8. Zero Boil Off System for Cryogen Storage Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This work proposes to develop a zero boil off (ZBO) dewar using a two-stage pulse-tube cooler together with two innovative, continuous-flow cooling loops and an...

  9. Boiling local heat transfer enhancement in minichannels using nanofluids.

    Science.gov (United States)

    Chehade, Ali Ahmad; Gualous, Hasna Louahlia; Le Masson, Stephane; Fardoun, Farouk; Besq, Anthony

    2013-03-18

    This paper reports an experimental study on nanofluid convective boiling heat transfer in parallel rectangular minichannels of 800 μm hydraulic diameter. Experiments are conducted with pure water and silver nanoparticles suspended in water base fluid. Two small volume fractions of silver nanoparticles suspended in water are tested: 0.000237% and 0.000475%. The experimental results show that the local heat transfer coefficient, local heat flux, and local wall temperature are affected by silver nanoparticle concentration in water base fluid. In addition, different correlations established for boiling flow heat transfer in minichannels or macrochannels are evaluated. It is found that the correlation of Kandlikar and Balasubramanian is the closest to the water boiling heat transfer results. The boiling local heat transfer enhancement by adding silver nanoparticles in base fluid is not uniform along the channel flow. Better performances and highest effect of nanoparticle concentration on the heat transfer are obtained at the minichannels entrance.

  10. Boiling of HFE-7100 on a Straight Pin Fin

    Institute of Scientific and Technical Information of China (English)

    Z. W. Liu; W.W. Lin; D.J. Lee; J.P. Hsu

    2001-01-01

    This paper deals with an experimental investigation of pin fin boiling of saturated and subcooled HFE-7100 under atmospheric pressure. Fin base temperature and heat flux data are measured along with the fin tip temperature. The basic features of boiling stability of HFE-7100 boiling on pin fin had been reported for the first time. For a given liquid/heating surface combination there exist upper steady-state (USS) branch and lower steady-state (LSS)branch, and a large, unstable regime located in between. Zones with different stability characteristics are mapped according to boiling on fins with different aspect ratios. Liquid subcooling can largely enhance heat transfer performance. A longer fin can provide a safer operation.

  11. An Analytical Approach for Relating Boiling Points of Monofunctional Organic Compounds to Intermolecular Forces

    Science.gov (United States)

    Struyf, Jef

    2011-01-01

    The boiling point of a monofunctional organic compound is expressed as the sum of two parts: a contribution to the boiling point due to the R group and a contribution due to the functional group. The boiling point in absolute temperature of the corresponding RH hydrocarbon is chosen for the contribution to the boiling point of the R group and is a…

  12. Heat transfer and pressure drop in flow boiling in microchannels

    CERN Document Server

    Saha, Sujoy Kumar

    2016-01-01

    This Brief addresses the phenomena of heat transfer and pressure drop in flow boiling in micro channels occurring in high heat flux electronic cooling. A companion edition in the Springer Brief Subseries on Thermal Engineering and Applied Science to “Critical Heat Flux in Flow Boiling in Micro channels,” by the same author team, this volume is idea for professionals, researchers and graduate students concerned with electronic cooling.

  13. Taylor stability of viscous fluids with application to film boiling

    Science.gov (United States)

    Dhir, V. K.; Lienhard, J. H.

    1973-01-01

    The dispersion relation is evaluated numerically for Taylor waves in a viscous unstable interface with surface tension. The solution takes account of transverse curvature and the numerical evaluations apply to horizontal cylindrical, as well as to plane, interfaces. The result is verified with frequency and wavelength data obtained during film boiling on horizontal wires. A very general empirical correlation is given, en passant, for the vapor blanket thickness during film boiling.

  14. Correlations estimate volume distilled using gravity, boiling point

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, A.; Consuelo Perez de Alba, M. del; Manriquez, L.; Guardia Mendoz, P. de la [Inst. Mexicano del Petroleo, Mexico City (Mexico)

    1995-10-23

    Mathematical nd graphic correlations have been developed for estimating cumulative volume distilled as a function of crude API gravity and true boiling point (TBP). The correlations can be used for crudes with gravities of 21--34{degree} API and boiling points of 150--540 C. In distillation predictions for several mexican and Iraqi crude oils, the correlations have exhibited accuracy comparable to that of laboratory measurements. The paper discusses the need for such a correlation and the testing of the correlation.

  15. Legal aspects and technical alternatives for the treatment of reservoir brines at the Activo Luna oilfield, Mexico.

    Science.gov (United States)

    Birkle, Peter; Cid Vázquez, Adolfo L; Fong Aguilar, J L

    2005-01-01

    Deep formation water, extracted as an undesired byproduct from on-shore production wells at the Activo Luna oilfield and processed in adjacent oil fields, are highly enriched in salt minerals, especially in sodium chloride (NaCl) (262 000 mg/L), but also in metals and nonmetals, such as strontium (Sr) (2068 mg/L), bromine (Br) (2034 mg/L), boron (B) (396 mg/ L), iodine (I) (43.4 mg/L), selenium (Se) (3.74 mg/L), and arsenic (As) (0.55 mg/L). Direct reinjection of the brine underground is not possible because of elevated pressure conditions within the petroleum reservoir. The disposal into near shore areas of the Gulf of Mexico without treatment must be rejected because of a) elevated concentrations of some toxic elements, such as B, silver (Ag), thallium (Tl), Se and cadmium (Cd), which exceed permissible limits of environmental legislation for surface discharge (Official Mexican norms NOM-001-ECOL-1998 and CE-CCA-001/89), and b) differences in density that could cause the descent of hypersaline fluid to the ocean floor, potentially affecting the diversity and survival of the benthic ecosystem. Conventional treatment techniques, such as microfiltration or reverse osmosis, are not suitable for the Activo Luna brines because of their extreme mineralization, which will cause pressure conditions exceeding 200 bars across the membrane. As an alternative process, the evaporation of the entire brine volume of approximately 200 m3/day by solar ponds or industrial crystallization plants is suggested. The residual precipitated residuals are composed mainly of chlorine (Cl) (9460 tons/year), sodium (Na) (4230 tons/ year), calcium (Ca) (1028 tons/year), potassium (K) (207 tons/year), and magnesium (Mg) (65.8 tons/year). As an alternative to its disposal on a dumpsite, some special minerals (especially NaCl, Mg, Sr, and Br) could be recovered for its economic value.

  16. Catalytic dehydration of carbohydrates suspended in organic solvents promoted by AlCl3 /SiO2 coated with choline chloride.

    Science.gov (United States)

    Yang, Jie; De Oliveira Vigier, Karine; Gu, Yanlong; Jérôme, François

    2015-01-01

    We show that the coating of choline chloride on silica-supported AlCl3 allows the dehydration of carbohydrates to successfully proceed in low boiling point organic solvents. The concept is based on the in situ formation of a deep eutectic liquid phase on the catalyst surface, thus facilitating the interaction between the solid catalyst and insoluble carbohydrate.

  17. Electrohydrodynamics of boiling on microstructured surfaces for space applications

    Science.gov (United States)

    Saccone, Giacomo; Moran, Jeffrey L.; Bucci, Matteo; Buongiorno, Jacopo; di Marco, Paolo; Mit-Nuclear Science; Engineering Team; University Of Pisa-Destec Dept. Team

    2016-11-01

    Surface wettability is a major parameter in boiling heat transfer. It affects the departure of bubbles from the boiling surface and consequently determines the maximum heat flux transferrable in safe conditions, known as critical heat flux (CHF). Surface wettability can be enhanced through passive techniques, including micro-engineered surfaces and coatings, or through active techniques, e.g. by applying a tunable electric field (electrowetting) that modifies the bubble shape in such a way as to drive bubble detachment. The latter technique is particularly interesting for space applications, where the electric field is used to create a body force that compensates for the absence of gravity. The present work is focused on boiling heat transfer on surfaces whose wettability has been modified by passive and active techniques. We have built a pool boiling apparatus composed of a micro-structured heater acting as boiling surface and an axisymmetric electrode High-speed optical and infrared imaging have been used to investigate the dynamics of boiling phenomena. The aims of this project are twofold: to achieve a superior understanding of wetting phenomena, and to improve the efficiency of cooling devices for space applications.

  18. Solar desalination, brine and fine chemicals - a preliminary report

    Digital Repository Service at National Institute of Oceanography (India)

    Shirodkar, P.V.; Nagarajan, R.

    from 3.65 - 4.63 ppm. The definite volumes of seawater samples (3.7 litres) taken in stills for desalination correspond to 13.08 - 31.16 mg of net boron content. Analyses on the recovery of the total content of boron in brines as well as in the bitterns...

  19. Solar desalination, brine and fine chemicals - a preliminary report

    Digital Repository Service at National Institute of Oceanography (India)

    Shirodkar, P.V.; Nagarajan, R.

    Solar stills put into operation by taking known quantities of sea water of different salinities varying from 27.75-36.27 x 10 super(3) during April-May 1990, indicated fresh water yield of 55-68% (av. 64). The volumes of brine as well as those...

  20. Brine Shrimp and Their Habitat, An Environmental Investigation.

    Science.gov (United States)

    National Wildlife Federation, Washington, DC.

    This environmental unit is one of a series designed for integration within the existing curriculum. The unit is self-contained and students are encouraged to work at their own speed. The philosophy of the unit is based on an experience-oriented process that encourages independent student work. This unit explores the life cycle of brine shrimp and…

  1. Uranium (VI) solubility in carbonate-free ERDA-6 brine

    Energy Technology Data Exchange (ETDEWEB)

    Lucchini, Jean-francois [Los Alamos National Laboratory; Khaing, Hnin [Los Alamos National Laboratory; Reed, Donald T [Los Alamos National Laboratory

    2010-01-01

    When present, uranium is usually an element of importance in a nuclear waste repository. In the Waste Isolation Pilot Plant (WIPP), uranium is the most prevalent actinide component by mass, with about 647 metric tons to be placed in the repository. Therefore, the chemistry of uranium, and especially its solubility in the WIPP conditions, needs to be well determined. Long-term experiments were performed to measure the solubility of uranium (VI) in carbonate-free ERDA-6 brine, a simulated WIPP brine, at pC{sub H+} values between 8 and 12.5. These data, obtained from the over-saturation approach, were the first repository-relevant data for the VI actinide oxidation state. The solubility trends observed pointed towards low uranium solubility in WIPP brines and a lack of amphotericity. At the expected pC{sub H+} in the WIPP ({approx} 9.5), measured uranium solubility approached 10{sup -7} M. The objective of these experiments was to establish a baseline solubility to further investigate the effects of carbonate complexation on uranium solubility in WIPP brines.

  2. Oil production enhancement through a standardized brine treatment. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Adewumi, A.; Watson, R.; Tian, S.; Safargar, S.; Heckman, S.; Drielinger, I.

    1995-08-01

    In order to permit the environmentally safe discharge of brines produced from oil wells in Pennsylvania to the surface waters of the Commonwealth and to rapidly brings as many wells as possible into compliance with the law, the Pennsylvania Oil and Gas Association (POGAM) approached the Pennsylvania State University to develop a program designed to demonstrate that a treatment process to meet acceptable discharge conditions and effluent limitations can be standardized for all potential stripper wells brine discharge. After the initial studies, the first phase of this project was initiated. A bench-scale prototype model was developed for conducting experiments in laboratory conditions. The experiments pursued in the laboratory conditions were focused on the removal of ferrous iron from synthetically made brine. Iron was selected as the primary heavy metals for studying the efficiency of the treatment process. The results of a number of experiments in the lab were indicative of the capability of the proposed brine treatment process in the removal of iron. Concurrent with the laboratory experiments, a comprehensive and extensive kinetic study was initiated. This study was necessary to provide the required data base for process modeling. This study included the investigation of the critical pH as well as the rate and order of reactions of the studied elements: aluminum, lead, zinc, and copper. In the second phase of this project, a field-based prototype was developed to evaluate and demonstrate the treatment process effectiveness. These experiments were conducted under various conditions and included the testing on five brines from different locations with various dissolved constituents. The outcome of this research has been a software package, currently based on iron`s reactivity, to be used for design purposes. The developed computer program was refined as far as possible using the results from laboratory and field experiments.

  3. Brine migration in salt and its implications in the geologic disposal of nuclear waste

    Energy Technology Data Exchange (ETDEWEB)

    Jenks, G.H.; Claiborne, H.C.

    1981-12-01

    This report respresents a comprehensive review and analysis of available information relating to brine migration in salt surrounding radioactive waste in a salt repository. The topics covered relate to (1) the characteristics of salt formations and waste packages pertinent to considerations of rates, amounts, and effects of brine migration, (2) experimental and theoretical information on brine migration, and (3) means of designing to minimize any adverse effects of brine migration. Flooding, brine pockets, and other topics were not considered, since these features will presumably be eliminated by appropriate site selection and repository design. 115 references.

  4. Void fraction prediction in saturated flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Francisco J Collado [Dpto de Ingenieria Mecanica-Motores Termicos, CPS-B, Universidad de Zaragoza, Maria de Luna 50018-Zaragoza (Spain)

    2005-07-01

    Full text of publication follows: An essential element in thermal-hydraulics is the accurate prediction of the vapor void fraction, or fraction of the flow cross-sectional area occupied by steam. Recently, the author has suggested to calculate void fraction working exclusively with thermodynamic properties. It is well known that the usual 'flow' quality, merely a mass flow rate ratio, is not at all a thermodynamic property because its expression in function of thermodynamic properties includes the slip ratio, which is a parameter of the process not a function of state. By the other hand, in the classic and well known expression of the void fraction - in function of the true mass fraction of vapor (also called 'static' quality), and the vapor and liquid densities - does not appear the slip ratio. Of course, this would suggest a direct procedure for calculating the void fraction, provided we had an accurate value of the true mass fraction of vapor, clearly from the heat balance. However the classic heat balance is usually stated in function of the 'flow' quality, what sounds really contradictory because this parameter, as we have noted above, is not at all a thermodynamic property. Then we should check against real data the actual relationship between the thermodynamic properties and the applied heat. For saturated flow boiling just from the inlet of the heated tube, and not having into account the kinetic and potential terms, the uniform applied heat per unit mass of inlet water and per unit length (in short, specific linear heat) should be closely related to a (constant) slope of the mixture enthalpy. In this work, we have checked the relation between the specific linear heat and the thermodynamic enthalpy of the liquid-vapor mixture using the actual mass fraction. This true mass fraction is calculated using the accurate measurements of the outlet void fraction taken during the Cambridge project by Knights and Thom in the sixties for

  5. Heat transfer mechanisms in microgravity flow boiling.

    Science.gov (United States)

    Ohta, Haruhiko

    2002-10-01

    The objective of this paper is to clarify the mechanisms of heat transfer and dryout phenomena in flow boiling under microgravity conditions. Liquid-vapor behavior in annular flow, encountered in the moderate quality region, has extreme significance for practical application in space. To clarify the gravity effect on the heat transfer observed for an upward flow in a tube, the research described here started from the measurement of pressure drop for binary gas-liquid mixture under various gravity conditions. The shear stress acting on the surface of the annular liquid film was correlated by an empirical method. Gravity effects on the heat transfer due to two-phase forced convection were investigated by the analysis of velocity and temperature profiles in the film. The results reproduce well the trends of heat transfer coefficients varying with the gravity level, quality, and mass velocity. Dryout phenomena in the moderate quality region were observed in detail by the introduction of a transparent heated tube. At heat fluxes just lower and higher than CHF value, a transition of the heat transfer coefficient was calculated from oscillating wall temperature, where a series of opposing heat transfer trends--the enhancement due to the quenching of dried areas or evaporation from thin liquid films and the deterioration due to the extension of dry patches--were observed between the passage of disturbance waves. The CHF condition that resulted from the insufficient decrease of wall temperature in the period of enhanced heat transfer was overcome by a temperature increase in the deterioration period. No clear effect of gravity on the mechanisms of dryout was observed within the range of experiments.

  6. Assessment of Brine Management for Geologic Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Breunig, Hanna M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Birkholzer, Jens T. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Borgia, Andrea [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Price, Phillip N. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Oldenburg, Curtis M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; McKone, Thomas E. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

    2013-06-13

    Geologic carbon sequestration (GCS) is the injection of carbon dioxide (CO2), typically captured from stationary emission sources, into deep geologic formations to prevent its entry into the atmosphere. Active pilot facilities run by regional United States (US) carbon sequestration partnerships inject on the order of one million metric tonnes (mt) CO2 annually while the US electric power sector emits over 2000 million mt-CO2 annually. GCS is likely to play an increasing role in US carbon mitigation initiatives, but scaling up GCS poses several challenges. Injecting CO2 into sedimentary basins raises fluid pressure in the pore space, which is typically already occupied by naturally occurring, or native, brine. The resulting elevated pore pressures increase the likelihood of induced seismicity, of brine or CO2 escaping into potable groundwater resources, and of CO2 escaping into the atmosphere. Brine extraction is one method for pressure management, in which brine in the injection formation is brought to the surface through extraction wells. Removal of the brine makes room for the CO2 and decreases pressurization. Although the technology required for brine extraction is mature, this form of pressure management will only be applicable if there are cost-­effective and sustainable methods of disposing of the extracted brine. Brine extraction, treatment, and disposal may increase the already substantial capital, energy, and water demands of Carbon dioxide Capture and Sequestration (CCS). But, regionally specific brine management strategies may be able to treat the extracted water as a source of revenue, energy, and water to subsidize CCS costs, while minimizing environmental impacts. By this approach, value from the extracted water would be recovered before disposing of any resulting byproducts. Until a price is placed on carbon, we expect that utilities and other CO2 sources will be

  7. Natural Oxidation of Bromide to Bromine in Evaporated Dead Sea Brines

    Science.gov (United States)

    Gavrieli, Ittai; Golan, Rotem; Lazar, Boaz; Baer, Gidi; Zakon, Yevgeni; Ganor, Jiwchar

    2016-04-01

    Highly evaporated Dead Sea brines are found in isolated sinkholes along the Dead Sea. Many of these brines reach densities of over 1.3 kg/L and pHDead Sea brine that drain into the sinkholes. The low pH and the reddish to brownish hue of these brines were an enigma until recently. Despite the rather high total alkalinity (TA) of the Dead Sea (3.826 mmol/kg) the pH of the Dead Sea brine is known to be slightly acidic with a value of ~6.3. In comparison, seawater with the same alkalinity would have a pH value well above 8.3, meaning that H+ activity is 100 fold lower than that of Dead Sea brine. In the present work we assess the apparent dissociation constant value of boric acid (K`B) for the Dead Sea brine and use it to explain the brine's low pH value. We then show that pH decreases further as the brine evaporates and salinity increases. Finally we explain the reddish hue of the hypersaline brines in the sinkholes as due to the presence of dissolved bromine. The latter is the product of oxidation of dissolved bromide, a process that is enabled by the low pH of the hypersaline brines and their high bromide concentration.

  8. Evaluation and analysis of underground brine resources in the southern coastal area of Laizhou Bay

    Science.gov (United States)

    Tian, M.; Zhu, H. T.; Feng, J.; Zhao, Q. S.

    2016-08-01

    The southern coastal districts of Laizhou Bay are some of the most important areas for underground brine exploitation in Shandong Province. Recently, these areas have been gradually developed by the underground brine mining industry. Such economic interest has led to brine exploitation so that underground brine resources are running out. Based on this phenomenon, this study describes the supply, runoff and draining conditions of the area by collecting and organizing the background information of the studied area. Hydrogeological parameters are then calculated according to pumping tests, and the amount of sustainable resources in the coastal areas of the Southern Bank of Laizhou Bay are then calculated based on the uniform distribution of wells. Under the circumstances of underground brine mining, the exploitation potential of the underground brine is evaluated in accordance with the calculation results of exploitation quantum. Finally, suggestions are provided for the sustainable exploitation of underground brine in the area.

  9. Molds in Brined Cucumbers: Cause of Softening During Air-Purging of Fermentations †

    Science.gov (United States)

    Costilow, Ralph N.; Gates, Karen; Lacy, Melvyn L.

    1980-01-01

    Softening of cucumbers in fermentations purged at high air-flow rates was caused by molds growing in the brined cucumbers, not in the brine. This conclusion is based on the following results: (i) no microorganisms were isolated in significant numbers from brines that caused softening of pasteurized brined cucumbers, (ii) no pectinolytic enzyme activities were produced in cucumber brines in the absence of cucumbers, (iii) the pickles in some air-purged fermentations became very soft without the appearance of any pectinolytic enzyme activity in the brine, (iv) mold hyphae were consistently observed in tissues of soft pickles, (v) molds consistently developed in cultures of slices of surface sterilized cucumbers taken from fermentations in which soft pickles were subsequently found, and (vi) molds belonging to the genera Alternaria, Fusarium, and Mucor isolated from slices all softened pasteurized brined cucumbers. Images PMID:16345619

  10. Preliminary lead isotope investigations of brine from the Red Sea, Galena from the Kingdom of Saudi Arabia, and galena from United Arab Republic (Egypt)

    Science.gov (United States)

    Delevaux, M.H.; Doe, B.R.; Brown, G.F.

    1967-01-01

    The isotopic composition of lead in Red Sea chloride brine containing 0.5 ppm Pb is found to be similar to that of some Cenozoic ore leads such as galena at Rabigh in Saudi Arabia that may have formed during mineralization accompanying Tertiary rifting. Bir Ranga galena in Miocene sediments from United Arab Republic (Egypt) is also isotopically similar to lead in Red Sea brine. The chlorine brine must be considered a possible mineralizing fluid. Lead isotopes show promise for use in mineral prospect evaluation in that galena from Samrah is isotopically similar to that from Mahd adh Dhahab, which has been the only ore producer in Saudi Arabia since 1945. Drilling at Samrah does indicate a possible economic mineralization. The lead isotope data coupled with available geologic knowledge and geochronometry are used to tentatively divide the ore prospects of the Kingdom of Saudi Arabia into relative categories of mineralization age. Two Mesozoic and Cenozoic mineralizations are distinguished on the basis of a 207Pb/204Pb difference; an early Paleozoic mineralization grouping is outlined; and a late Precambrian mineralization period is suggested. ?? 1967.

  11. Stability of α-tocotrienol and α-tocopherol in salami-type sausages and curing brine depending on nitrite and pH.

    Science.gov (United States)

    Gerling, Eva-Maria; Ternes, Waldemar

    2014-12-01

    We studied the stability of the valuable vitamer nutrients α-tocotrienol and α-tocopherol and options for their protection in salami-type sausages (blended with α-tocotrienol-rich barley oil) and curing brine. Four different sausage formulations were produced containing nitrite curing salt; nitrite curing salt and ascorbic acid (300mg/kg); nitrite curing salt and carnosic acid (45mg/kg); or sodium chloride. Initial vitamer contents (100mg/kg) did not decrease significantly during ripening and decreased only slightly during storage. Ascorbic acid and carnosic acid were found to be effective in preserving the vitamers in fresh sausages. Freeze-drying of sausages resulted in a significant loss of vitamers (97%), particularly after 14-day storage at room temperature, even in the presence of shielding gases. The vitamer content in the curing brine decreased with decreasing pH in the presence of nitrite. A nitrite concentration of 136mg/L at pH4 resulted in significant loss (90%) of the vitamers. Sufficient stability of the vitamers in salami-type sausage and curing brine can be achieved by processing, formulation, and storage conditions.

  12. Inspection of Pool Boiling with Superhydrophilic and Superhydrophobic Coating

    Energy Technology Data Exchange (ETDEWEB)

    Son, Gyumin; Moon, Sung Bo; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of)

    2015-05-15

    In conventional nuclear power plants, increasing critical heat flux (CHF) margin by converting existing parts is economically meaningful since it means overall energy production increase without building additional power plants. There were researches to enhance margin from the very beginning of the commercialization of nuclear power plants and many efforts have led to current model of plants, optimized for both safety and production efficiency. Examples are mixing vane which is actually applied to plants nowadays, using nanofluids to enhance heat transfer coefficient (HTC), trying porous surfaces and so on. Takata et al. studied effects of surface wettability by using hydrophobic coating and observed enhanced nucleate boiling at coated surface regions. Betz et al. experimented superhydrophilic (SHPi), superhydrophobic (SHPo), and superbiphilic surfaces. Results indicate heat transfer coefficient enhancement due to increase of nucleation sites by hydrophobic regions and constrained diameter of growing bubbles by hydrophilic regions. Although it would be rough to apply their concept to real reactor coolant surface wall, understanding the possibility of enhanced boiling is meaningful. In this paper, SHPi and SHPo coatings were applied to wire at traditional pool boiling experiment by Nukiyama. By observing altered CHF margin and nucleate boiling, the effects of each coating and their tendencies are discussed. SHPi, SHPo and bare wire's pool boiling was investigated and their boiling graphs were discussed. SHPi shows enhancement in CHF while SHPo's case is more complicated since there were variables like partial CHF or micro scale bubbles. Additional experiment could be comparing HTC, checking whether hydrophobic wire's nucleate boiling enhancement can exceed the decreased CHF margin. More sophisticated method to remove unwanted bubbles should be considered such as using degassed water.

  13. Study of film boiling collapse behavior during vapor explosion

    Energy Technology Data Exchange (ETDEWEB)

    Yagi, Masahiro; Yamano, Norihiro; Sugimoto, Jun [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Abe, Yutaka; Adachi, Hiromichi; Kobayashi, Tomoyoshi

    1996-06-01

    Possible large scale vapor explosions are safety concern in nuclear power plants during severe accident. In order to identify the occurrence of the vapor explosion and to estimate the magnitude of the induced pressure pulse, it is necessary to investigate the triggering condition for the vapor explosion. As a first step of this study, scooping analysis was conducted with a simulation code based on thermal detonation model. It was found that the pressure at the collapse of film boiling much affects the trigger condition of vapor explosion. Based on this analytical results, basic experiments were conducted to clarify the collapse conditions of film boiling on a high temperature solid ball surface. Film boiling condition was established by flooding water onto a high temperature stainless steel ball heated by a high frequency induction heater. After the film boiling was established, the pressure pulse generated by a shock tube was applied to collapse the steam film on the ball surface. As the experimental boundary conditions, materials and size of the balls, magnitude of pressure pulse and initial temperature of the carbon and stainless steel balls were varied. The transients of pressure and surface temperature were measured. It was found that the surface temperature on the balls sharply decreased when the pressure wave passed through the film on balls. Based on the surface temperature behavior, the film boiling collapse pattern was found to be categorized into several types. Especially, the pattern for stainless steel ball was categorized into three types; no collapse, collapse and reestablishment after collapse. It was thus clarified that the film boiling collapse behavior was identified by initial conditions and that the pressure required to collapse film boiling strongly depended on the initial surface temperature. The present results will provide a useful information for the analysis of vapor explosions based on the thermal detonation model. (J.P.N.)

  14. Brine Inclusions Migration in Intact Salt Crystals under Thermal Gradient

    Science.gov (United States)

    Caporuscio, F.; Boukhalfa, H.

    2013-12-01

    The behavior of water contained in rock salt under the influence of thermal gradients is critical to the performance of salt as a medium for the disposal of nuclear waste. Water contained in salt can be present as discrete inclusions within intact salt crystals, at the interface between salt crystals and aggregates, and also as hydration water and structural water present in accessory minerals present in salt. Water content in pure halite salt usually rages from 0.1 to 0.5 wt. % but is significantly higher in clay rich salt, for which water content can be up to several wt. %. Under the influence of thermal gradients brine inclusions and water associated to the accessory mineral is mobilized. Previous investigations have shown brine inclusions tend to move towards the heat source through a mechanism that involves the dissolution of salt at the hot face of the brine inclusion and its precipitation at the colder side of the inclusion. Uncertainties remain on the exact parameters that define the rate of brine migration and whether it truly migrates to towards the heat source. We performed studies under controlled thermal gradients to examine the behavior of brine inclusions in single salt crystals obtained from the underground salt mine at the Waste Isolation Power Plant (WIPP). We found that the behavior of the brine inclusions under thermal gradients is dependent on the thermal gradient magnitude and the nature of the inclusion. Full inclusions (liquid only) migrate predominantly towards the heat source, but when the inclusions are large and close to the surface they fracture the salt and release water near the surface. Inclusions that migrate towards the heat source migrate through a mechanism that involves the dissolution of salt at the hot side of the inclusion and its deposition along the migration path. SEM analysis of the migration pathways shows that brine migrates through the creation of a network of square shaped hollow channels of about 10 micron diameter

  15. Benzalkonium Chloride and Glaucoma

    OpenAIRE

    Rasmussen, Carol A.; Kaufman, Paul L.; Kiland, Julie A.

    2014-01-01

    Glaucoma patients routinely take multiple medications, with multiple daily doses, for years or even decades. Benzalkonium chloride (BAK) is the most common preservative in glaucoma medications. BAK has been detected in the trabecular meshwork (TM), corneal endothelium, lens, and retina after topical drop installation and may accumulate in those tissues. There is evidence that BAK causes corneal and conjunctival toxicity, including cell loss, disruption of tight junctions, apoptosis and preapo...

  16. ANTIMICROBIAL SCREENING AND BRINE SHRIMP LETHALITY BIOASSAY OF TINOSPORA CORDIFOLIA (FAM: MENISPERMACEAE

    Directory of Open Access Journals (Sweden)

    Mohammad Kaisarul Islam

    2011-12-01

    Full Text Available Tinospora cordifolia (Fam: Menispermaceae has been investigated for evaluation of the biological activities. The stem of Tinospora cordifolia were extracted with carbon tetrachloride, n-hexane and methanol were collected and afford 4.0 mg, 4.0 mg, and 4.0 mg, respectively for the test. The crude carbon tetrachloride, n-hexane, and methanol extract of the plant were subjected to antimicrobial screening against 15 microorganisms such as gram-positive, gram-negative, fungi by the disc diffusion method. But interestingly no fraction showed any inhibitory effect against all the microorganisms. In the brine shrimp lethality bioassay, carbon tetrachloride fraction showed high toxicity, where LC90 value was only 6.25 mg/ml. The methanol crude extract and n-hexane fraction showed LC50 of 1.563 and 6.05 mg/ml respectively with very narrow therapeutic index (LC90 of 43.0 mg/ml and 45.0 mg/ml respectively. This indicated that the cytotoxicity exhibited by the carbon tetra chloride, n-hexane, and methanol extract was very significant.

  17. Optimisation of Fenton's reagent usage as a pre-treatment for fermentation brines.

    Science.gov (United States)

    Rivas, Francisco J; Beltrán, Fernando J; Gimeno, Olga; Alvarez, Pedro

    2003-01-31

    Pre-treatment of fermentation brines from green olives has been carried out by the Fe(II)/Fe(III)/H(2)O(2) system. Reagent concentration exerted a positive influence on chemical oxygen demand (COD) removal. Hydrogen peroxide uptake showed values in the range 0.3-1.6mol of COD eliminated per mol of H(2)O(2) consumed depending on operating conditions. The optimum working pH was found to be in the interval 2.0-3.5. Reaction temperature increased the COD degradation rate, although similar COD conversion values were obtained after 5h of treatment regardless of the value of this parameter. An analysis of the biodegradability of this type of effluent demonstrated the beneficial effect of the chemical pre-oxidation. According to the experimental results, it is suggested that there is an inhibitory effect of the wastewater due to its COD content and nature rather than attributable to the presence of high amounts of sodium chloride. Biodegradation efficiency increased as temperature was raised up to 30 degrees C. A further increase of this parameter up to 40 degrees C resulted in the death of the microorganisms.

  18. Groundwater Sustainability in the Michigan Lowlands - Understanding the Complex Interplay of Natural Brine Upwelling, Human Activity, and Climate Change

    Science.gov (United States)

    Curtis, Z. K.; Li, S. G.; Sampath, P. V.; Liao, H. S.

    2015-12-01

    This research investigates a relatively unknown, basin-scale contamination hazard threatening the long-term sustainability of groundwater resources in the Lower Peninsula of Michigan (LPM). Many studies across LPM report elevated chloride concentrations ([Cl-]>250 mg/L) in the near-surface water, including the Michigan lowlands (west LPM), the Saginaw lowlands (east LPM) - where the upwelling of deep brines was inferred as the source - and at discrete points further inland. This begs the question: do the scattered occurrences of elevated [Cl-] share a common underlying mechanism, namely, the upwelling of brine? We addresses this question with data-driven modeling of the [Cl-] dynamics and hydrology across multiple scales, capitalizing on two massive statewide databases with water quality information from over 106 wells and static water levels (SWL) from roughly 500,000 wells. Long-term SWL were mapped at the basin-, regional-, and local-scale to identify recharge/discharge areas. Wells with elevated [Cl-] were overlaid to each map, revealing a consistent pattern of low [Cl-] in recharge areas and elevated [Cl-] in discharge areas. This multi-scale relationship provides compelling evidence for upwelling of brines, a concept supported by the analysis of 450 well samples collected in the Michigan lowlands which showed [Cl-] generally increases with depth. We assessed temporal trends by comparing field results to past records at 249 sampling locations. Most of the sites exhibit an increase of [Cl-] in recent years, which roughly coincides with a time period when Lake Michigan-Huron levels systematically decreased. Moreover, recent increases in [Cl-] are focused to areas where temporal analysis of SWL indicated increased well withdrawals. The results show that the contamination is caused by upwelling brines, and suggest that it is becoming more severe in recent years. Future work will integrate multi-scale, process-based groundwater modeling with further data collection

  19. Marangoni heat transfer in subcooled nucleate pool boiling

    Energy Technology Data Exchange (ETDEWEB)

    Petrovic, S.; Robinson, T.; Judd, R.L. [McMaster University, Hamilton, ON (Canada). Dept. of Mechanical Engineering

    2004-11-01

    The liquid motion induced by surface tension variation, termed the Marangoni effect, and its contribution to boiling heat transfer has been an issue of much controversy. Boiling heat transfer theory, although acknowledging its existence, considers its contribution to heat transfer to be insignificant in comparison with buoyancy induced convection. However, recent microgravity experiments have shown that although the boiling mechanism in a reduced gravity environment is different, the corresponding heat transfer rates are similar to those obtained under normal gravity conditions, raising questions about the validity of the assumption. An experimental investigation was performed in which distilled water was gradually heated to boiling conditions on a copper heater surface at four different levels of subcooling. Photographic investigation of the bubbles appearing on the surface was carried out in support of the measurements. The results obtained indicate that Marangoni convection associated with the bubbles formed by the air dissolved in the water which emerged from solution when the water was heated sufficiently, significantly influenced the heat transfer rate in subcooled nucleate pool boiling. A heat transfer model was developed in order to explain the phenomena observed. (author)

  20. Heater size effect on subcooled pool boiling of FC-72

    Energy Technology Data Exchange (ETDEWEB)

    Raj, Rishi; Kim, Jungho [University of Maryland, College Park, MD (United States). Dept. of Mechanical Engineering

    2009-07-01

    Extensive research has been conducted on pool boiling using heaters larger than the capillary length. For large heaters and/or high gravity conditions, boiling is dominated by buoyancy, and the heat transfer is heater size independent. Much less is known about boiling on small heaters and at low gravity levels. The ratio of heater size L{sub h} to capillary length L{sub c} is an important parameter in the determination of heater size dependence on heat transfer. As the ratio L{sub h}/L{sub c} decreases due to a decrease in either heater size or gravity, surface tension forces become dominant. It is proposed that transition from buoyancy to surface tension dominated boiling occurs when the heater size and bubble departure diameter are of the same order. Previous work in variable gravity with flat surfaces has shown that the heat transfer was heater size independent only when the ratio L{sub h}/L{sub c} was considerably larger than 1. An array of 96 platinum resistance heater elements in a 10 x 10 configuration with individual elements 0.7 x 0.7 mm{sup 2} in size was used to vary heater size and measure the heat transfer. The threshold value of L{sub h}/L{sub c} above which pool boiling is heater size independent was found to be about 2.8. (author)

  1. Boiling crisis and non-equilibrium drying transition

    CERN Document Server

    Nikolayev, Vadim

    2016-01-01

    Boiling crisis is the rapid formation of the quasi-continuous vapor film between the heater and the liquid when the heat supply exceeds a critical value. We propose a mechanism for the boiling crisis that is based on the spreading of the dry spot under a vapor bubble. The spreading is initiated by the vapor recoil force, a force coming from the liquid evaporation into the bubble. Since the evaporation intensity increases sharply near the triple contact line, the influence of the vapor recoil can be described as a change of the apparent contact angle. Therefore, for the most usual case of complete wetting of the heating surface by the liquid, the boiling crisis can be understood as a drying transition from complete to partial wetting. The state of nucleate boiling, which is boiling in its usual sense, is characterized by a very large rate of heat transfer from the heating surface to the bulk because the superheated liquid is carried away from the heating surface by the departing vapor bubbles. If the heating p...

  2. Gravity and Heater Size Effects on Pool Boiling Heat Transfer

    Science.gov (United States)

    Kim, Jungho; Raj, Rishi

    2014-01-01

    The current work is based on observations of boiling heat transfer over a continuous range of gravity levels between 0g to 1.8g and varying heater sizes with a fluorinert as the test liquid (FC-72/n-perfluorohexane). Variable gravity pool boiling heat transfer measurements over a wide range of gravity levels were made during parabolic flight campaigns as well as onboard the International Space Station. For large heaters and-or higher gravity conditions, buoyancy dominated boiling and heat transfer results were heater size independent. The power law coefficient for gravity in the heat transfer equation was found to be a function of wall temperature under these conditions. Under low gravity conditions and-or for smaller heaters, surface tension forces dominated and heat transfer results were heater size dependent. A pool boiling regime map differentiating buoyancy and surface tension dominated regimes was developed along with a unified framework that allowed for scaling of pool boiling over a wide range of gravity levels and heater sizes. The scaling laws developed in this study are expected to allow performance quantification of phase change based technologies under variable gravity environments eventually leading to their implementation in space based applications.

  3. The evolution of the Dead Sea brine during the last 220 ky as revealed by porewater Cl-, Na+ and δ18O in ICDP deep core

    Science.gov (United States)

    Lazar, Boaz; Levy, Elan J.; Sivan, Orit; Yechieli, Joseph; Antler, Gilad; Gavrieli, Ittai; Stein, Mordechai

    2016-04-01

    The chemical composition of pore brines extracted from 456 m long core drilled by the ICDP during 2011 in the deep basin (water depth of 300 m) of the Dead Sea provides a history of the evolution of the Dead Sea brine during the last 220 ky. The vertical profiles of chloride (Cl-) sodium (Na+) and oxygen isotopes (δ18O) in the core show that during that period the bottom water mass (hypolimnion) of the lake was always hyper-saline and its salinity did not dropped below ~70 % of that of the modern Dead Sea. The lake underwent three major hyper-arid periods that lasted altogether about 30 ky and deposited ~150 m of halite and gypsum. These periods were the last two interglacials and the postglacial till present. During the last glacial and particularly during MIS2 (~31-17 ka BP) the salinity of the lake dropped substantially due to excess input of freshwater as indicated by the decrease in Cl- and Na+ of the hypolimnion. The δ18O at the same period increased to maximum of ~7‰ (3‰ higher than today). The variations in Na+ and Cl- during the "freshening" period suggest that halite dissolution, probably due to the rise of mount Sedom diapir, "buffered" the brine from further drop in salinity. The dilution of the brine was slow and lasted more than 10 ky probably due to continuous turbulent mixing of the hypolimnion with the less saline high δ18O epilimnetic brine that underwent "normal" evaporation. The low δ18O during high salinity -halite deposition- periods is attributed to "reversed" behavior of δ18O during evaporation of high salinity brine. Massive precipitation of halite during the last 10 ky decreased sharply the Na+/Cl- ratio of the Dead Sea from ~0.7 to its present value of ~0.2. A similar low value was reached during the last interglacial, at ~120 ky. Both periods mark the most mature evaporative state of the lake during the last 220 ky.

  4. The determination of vanadium in brines by atomic absorption spectroscopy

    Science.gov (United States)

    Crump-Wiesner, Hans J.; Feltz, H.R.; Purdy, W.C.

    1971-01-01

    A standard addition method is described for the determination of vanadium in brines by atomic absorption spectroscopy with a nitrous oxide-acetylene flame. Sample pH is adjusted to 1.0 with concentrated hydrochloric acid and the vanadium is directly extracted with 5% cupferron in methyl isobutyl ketone (MIBK). The ketone layer is then aspirated into the flame and the recorded absorption values are plotted as a function of the concentration of the added metal. As little as 2.5 ??g l-1 of vanadium can be detected under the conditions of the procedure. Tungsten and tin interfere when present in excess of 5 and 10 ??g ml-1, respectively. The concentrations of the two interfering ions normally found in brines are well below interference levels. ?? 1971.

  5. Stabilization of high mercury contaminated brine purification sludge.

    Science.gov (United States)

    Zhuang, J Ming; Lo, Tony; Walsh, Tony; Lam, Tak

    2004-09-10

    The highly leachable mercury contaminants of brine purification sludge (BPS) generated from the Hg-cell electrolysis process in chlorine production can be stabilized in the treatment procedure employing ferric-lignin derivatives (FLD) (Ligmet binder) and Portland cement (PC). The stabilization effectiveness has been examined by time-based multiple toxicity characteristic leaching procedure (TCLP) tests and sequential TCLP tests. In a period of 50 days, the multiple TCLP tests showed a variation of less than 90 microg l(-1) for the leachable mercury level, and the sequential TCLP tests for the same sample displayed a declining TCLP mercury level. Based on this study, the stabilization of approximately 2000 t of brine purification sludge has been successfully processed with the ferric-lignin derivatives treatment.

  6. Brine crude oil interactions at the oil-water interface

    DEFF Research Database (Denmark)

    Chakravarty, Krishna Hara; Fosbøl, Philip Loldrup; Thomsen, Kaj

    2015-01-01

    mechanisms. The ion specific interaction between fines and polar fractions of crude oil at the oil-water interface has been less explored. In this study the relative affinity between different ions and the oil surface was determined. The experiments prove the importance of Ca2+, SO42-, and HPO42- ions...... emulsion formation at 0.05 mol/1. The amount of emulsion formation showed significant dependency on the type of acid doped in oil. Experiments demonstrate that the brine solution can alter the micro forces at the oil-water interface, and this ion specific interaction leads to oil emulsion formation......The impact of brine salinity and its ionic composition on oil displacement efficiency has been investigated extensively in recent years due to the potential of enhanced oil recovery (EOR). Wettability alterations through relative interactions at the mineral surface have been the basis of proposed...

  7. Geochemical evolution of brines in the Salar of Uyuni, Bolivia.

    Science.gov (United States)

    Rettig, S.L.; Jones, B.F.; Risacher, F.

    1980-01-01

    Recent analyses of brines from the Salars of Uyuni and Coipasa have been compared with published data for Lakes Titicaca and Poopo to evaluate solute compositional trends in these remnants of two large Pleistocene lakes once connected by overflow from the N to the S of the Bolivian Altiplano. From Titicaca to Poopo the water shows an increase in Cl and N somewhat greater than the total solutes. Ca and SO4 increase to a lesser extent than total dissolved solids, and carbonate species are relatively constant. Between Poopo and Coipasa proportions of Ca, SO4 and CO3 continue to decrease. At Coipasa and Uyuni, the great salars frequently evaporate to halite saturation. Halite crystallization is accompanied by an increased K, Mg and SO4 in residual brines. - from Authors

  8. Bioencapsulation of metronidazole in adult brine shrimp (Artemia sp.).

    Science.gov (United States)

    Allender, Matthew C; Kastura, Mike; George, Robert; Bulman, Frank; Yarbrough, Jason; Cox, Sherry

    2011-06-01

    A description of bioencapsulation of metronidazole in adult brine shrimp (Artemia) for 2.5 g/L, 5 g/L, and 10 g/L treatment baths is presented. Metronidazole was detected in adult brine shrimp tissue after enrichment periods of 15 min, 30 min, 1 hr, 2 hr, 4 hr, 8 hr, 12 hr, and 24 hr. The assays were performed using high performance liquid chromatography. There was a positive relationship in both dose and time. When evaluating percent uptake, all three baths demonstrated a similar pattern. All three bath concentrations had a high initial concentration that fell at 30 min and slowly began to increase through the end of the study. Survival of shrimp was not affected by bath concentration but decreased over time in all treatment baths comparatively. It can be concluded that metronidazole can be successfully bioencapsulated in adult Artemia.

  9. An improved brine shrimp larvae lethality microwell test method.

    Science.gov (United States)

    Zhang, Yi; Mu, Jun; Han, Jinyuan; Gu, Xiaojie

    2012-01-01

    This article described an improved brine shrimp larvae lethality microwell test method. A simply designed connecting vessel with alternative photoperiod was used to culture and collect high yield of active Artemia parthenogenetica nauplii for brine shrimp larvae lethality microwell test. Using this method, pure A. parthenogenetica nauplii suspension was easily cultured and harvested with high density about 100-150 larvae per milliliter and the natural mortality was reduced to near zero by elimination of unnecessary artificial disturbance. And its sensitivity was validated by determination of LC(50)-24 h of different reference toxicants including five antitumor agents, two pesticides, three organic pollutants, and four heavy metals salts, most of which exhibited LC(50)-24 h between 0.07 and 58.43 mg/L except for bleomycin and mitomycin C with LC(50)-24 h over 300 mg/L.

  10. Transient heat conduction through a substrate of brine-spongy ice

    Science.gov (United States)

    Dehghani, S. R.; Naterer, G. F.; Muzychka, Y. S.

    2017-03-01

    An analytical model for heat conduction through brine-spongy ice is developed. This model fills a gap in knowledge related to transient heat conduction to a two-phase substrate which is crucial for modeling transient icing and deicing of cold surfaces in contact with salt water. The core of the model is based on the phase change of pure ice and brine pockets trapped in the structure of spongy ice. Freezing of brine pockets causes the release of the latent heat of fusion that is considered as the source of heat generation distributed throughout the brine-spongy ice. A nonlinear partial differential equation and a number of equations of state for ice, brine, and brine-spongy ice create governing equations of heat transfer through brine-spongy ice. A standard numerical scheme solves the set of equations in various initial conditions. The variation of temperature, volume fraction of brine and salinity of brine pockets are calculated numerically. Experimental samples of brine-spongy ice are examined under transient conditions and their surface temperatures are captured using an infrared thermal camera. The numerical results, which are for various overall salinities, are closely aligned with the measured surface temperatures.

  11. Numerical simulation of pool boiling of a Lennard-Jones liquid

    KAUST Repository

    Inaoka, Hajime

    2013-09-01

    We performed a numerical simulation of pool boiling by a molecular dynamics model. In the simulation, a liquid composed of Lennard-Jones particles in a uniform gravitational field is heated by a heat source at the bottom of the system. The model successfully reproduces the change in regimes of boiling from nucleate boiling to film boiling with the increase of the heat source temperature. We present the pool boiling curve by the model, whose general behavior is consistent with those observed in experiments of pool boiling. © 2013 Elsevier B.V. All rights reserved.

  12. Changes of enthalpy slope in subcooled flow boiling

    Science.gov (United States)

    Collado, Francisco J.; Monné, Carlos; Pascau, Antonio

    2006-03-01

    Void fraction data in subcooled flow boiling of water at low pressure measured by General Electric in the 1960s are analyzed following the classical model of Griffith et al. (in Proceedings of ASME-AIChE heat transfer conference, #58-HT-19, 1958). In addition, a new proposal for analyzing one-dimensional steady flow boiling is used. This is based on the physical fact that if the two phases have different velocities, they cannot cover the same distance—the control volume length—in the same time. So a slight modification of the heat balance is suggested, i.e., the explicit inclusion of the vapor liquid velocity ratio or slip ratio as scaling time factor between the phases, which is successfully checked against the data. Finally, the prediction of void fraction using correlations of the net rate of change of vapor enthalpy in the fully developed regime of subcooled flow boiling is explored.

  13. Boiling heat transfer on fins – experimental and numerical procedure

    Directory of Open Access Journals (Sweden)

    Orzechowski T.

    2014-03-01

    Full Text Available The paper presents the research methodology, the test facility and the results of investigations into non-isothermal surfaces in water boiling at atmospheric pressure, together with a discussion of errors. The investigations were conducted for two aluminium samples with technically smooth surfaces and thickness of 4 mm and 10 mm, respectively. For the sample of lower thickness, on the basis of the surface temperature distribution measured with an infrared camera, the local heat flux and the heat transfer coefficient were determined and shown in the form of a boiling curve. For the thicker sample, for which 1-D model cannot be used, numerical calculations were conducted. They resulted in obtaining the values of the local heat flux on the surface the invisible to the infrared, camera i.e. on the side on which the boiling of the medium proceeds.

  14. Changes of enthalpy slope in subcooled flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco J.; Monne, Carlos [Universidad de Zaragoza-CPS, Departamento de Ingenieria Mecanica-Motores Termicos, Zaragoza (Spain); Pascau, Antonio [Universidad de Zaragoza-CPS, Departamento de Ciencia de los Materiales y Fluidos-Mecanica de Fluidos, Zaragoza (Spain)

    2006-03-01

    Void fraction data in subcooled flow boiling of water at low pressure measured by General Electric in the 1960s are analyzed following the classical model of Griffith et al. (in Proceedings of ASME-AIChE heat transfer conference, 58-HT-19, 1958). In addition, a new proposal for analyzing one-dimensional steady flow boiling is used. This is based on the physical fact that if the two phases have different velocities, they cannot cover the same distance - the control volume length - in the same time. So a slight modification of the heat balance is suggested, i.e., the explicit inclusion of the vapor-liquid velocity ratio or slip ratio as scaling time factor between the phases, which is successfully checked against the data. Finally, the prediction of void fraction using correlations of the net rate of change of vapor enthalpy in the fully developed regime of subcooled flow boiling is explored. (orig.)

  15. Visualization of pool boiling from complex surfaces with internal tunnels

    Directory of Open Access Journals (Sweden)

    Pastuszko Robert

    2012-04-01

    Full Text Available The paper presents experimental investigations of boiling heat transfer for a system of connected narrow horizontal and vertical tunnels. These extended surfaces, named narrow tunnel structure (NTS, can be applied to electronic element cooling. The experiments were carried out with ethanol at atmospheric pressure. The tunnel external covers were manufactured out of 0.1 mm thick perforated copper foil (hole diameters 0.5 mm, sintered with the mini-fins, formed on the vertical side of the 10 mm high rectangular fins and horizontal inter-fin surface. Visualization studies were conducted with a transparent structured model of joined narrow tunnels limited with the perforated foil. The visualization investigations aimed to formulate assumptions for the boiling model through distinguishing boiling types and defining all phases of bubble growth.

  16. Micro-column enhanced boiling structure and its ramification

    Institute of Scientific and Technical Information of China (English)

    汤勇; 陆龙生; 袁冬; 苏达士

    2008-01-01

    Enhanced boiling experiments of two different enhanced structures were carried out in a thermosyphon loop evaporator chamber. One was micro-columns array structure (MCAS), which was fabricated on copper plate surface with interaction high speed wire electrode discharge machining (HS-WEDM). The other was the ramification of MCAS, named micro-column-array and sintered-copper compound structure (MSCS), which was fabricated with sintered method on micro-column array structure. Considering the wall superheat and critical heat flux (CHF), comparisons were made between them. The results show that both MCAS and MSCS can enhance the boiling heat transfer. It is also found that the enhanced boiling heat transfer ability of MSCS is changed obviously while the porosity of the sintered copper layer is changed.

  17. On mechanism of explosive boiling in nanosecond regime

    Science.gov (United States)

    Çelen, Serap

    2016-06-01

    Today laser-based machining is used to manufacture vital parts for biomedical, aviation and aerospace industries. The aim of the paper is to report theoretical, numerical and experimental investigations of explosive boiling under nanosecond pulsed ytterbium fiber laser irradiation. Experiments were performed in an effective peak power density range between 1397 and 1450 MW/cm2 on pure titanium specimens. The threshold laser fluence for phase explosion, the pressure and temperature at the target surface and the velocity of the expulsed material were reported. A narrow transition zone was realized between the normal vaporization and phase explosion fields. The proof of heterogeneous boiling was given with detailed micrographs. A novel thermal model was proposed for laser-induced splashing at high fluences. Packaging factor and scattering arc radius terms were proposed to state the level of the melt ejection process. Results of the present investigation explain the explosive boiling during high-power laser interaction with metal.

  18. A high-fidelity approach towards simulation of pool boiling

    Energy Technology Data Exchange (ETDEWEB)

    Yazdani, Miad; Radcliff, Thomas; Soteriou, Marios; Alahyari, Abbas A. [United Technologies Research Center, East Hartford, Connecticut 06108 (United States)

    2016-01-15

    A novel numerical approach is developed to simulate the multiscale problem of pool-boiling phase change. The particular focus is to develop a simulation technique that is capable of predicting the heat transfer and hydrodynamic characteristics of nucleate boiling and the transition to critical heat flux on surfaces of arbitrary shape and roughness distribution addressing a critical need to design enhanced boiling heat transfer surfaces. The macro-scale of the phase change and bubble dynamics is addressed through employing off-the-shelf Computational Fluid Dynamics (CFD) methods for interface tracking and interphase mass and energy transfer. The micro-scale of the microlayer, which forms at early stage of bubble nucleation near the wall, is resolved through asymptotic approximation of the thin-film theory which provides a closed-form solution for the distribution of the micro-layer and its influence on the evaporation process. In addition, the sub-grid surface roughness is represented stochastically through probabilistic density functions and its role in bubble nucleation and growth is then represented based on the thermodynamics of nucleation process. This combination of deterministic CFD, local approximation, and stochastic representation allows the simulation of pool boiling on any surface with known roughness and enhancement characteristics. The numerical model is validated for dynamics and hydrothermal characteristics of a single nucleated bubble on a flat surface against available literature data. In addition, the prediction of pool-boiling heat transfer coefficient is verified against experimental measurements as well as reputable correlations for various roughness distributions and different surface orientations. Finally, the model is employed to demonstrate pool-boiling phenomenon on enhanced structures with reentrance cavities and to explore the effect of enhancement feature design on thermal and hydrodynamic characteristics of these surfaces.

  19. Defluoridation of drinking water by boiling with brushite and calcite.

    Science.gov (United States)

    Larsen, M J; Pearce, E I F

    2002-01-01

    Existing methods for defluoridating drinking water involve expensive high technology or are slow, inefficient and/or unhygienic. A new method is now suggested, encompassing brushite and calcite suspension followed by boiling. Our aim was to examine the efficiency of the method and the chemical reactions involved. Brushite, 0.3-0.5 g, and an equal weight of calcite were suspended in 1 litre water containing 5-20 ppm fluoride. The suspensions were boiled in an electric kettle, left to cool and the calcium salts to sediment. Solution ion concentrations were determined and sediments were examined by X-ray diffraction. In distilled water initially containing 5, 10 and 20 ppm fluoride the concentration was reduced to 0.06, 0.4 and 5.9 ppm, respectively. Using Aarhus tap water which contained 2.6 mmol/l calcium the final concentrations were 1.2, 2.5 and 7.7 ppm, respectively, and runs without calcite gave results similar to those with calcite. Without boiling the fluoride concentration remained unaltered, as did the brushite and calcite salts, despite occasional agitation by hand. All solutions were supersaturated with respect to fluorapatite and hydroxyapatite and close to saturation with respect to brushite. Boiling produced well-crystallised apatite and traces of calcite, while boiling of brushite alone left a poorly crystallised apatite. We conclude that boiling a brushite/calcite suspension rapidly converts the two salts to apatite which incorporates fluoride if present in solution, and that this process may be exploited to defluoridate drinking water.

  20. High heat flux transport by microbubble emission boiling

    Science.gov (United States)

    Suzuki, Koichi

    2007-10-01

    In highly subcooled flow boiling, coalescing bubbles on the heating surface collapse to many microbubbles in the beginning of transition boiling and the heat flux increases higher than the ordinary critical heat flux. This phenomenon is called Microbubble Emission Boiling, MEB. It is generated in subcooled flow boiling and the maximum heat flux reaches about 1 kW/cm2(10 MW/m2) at liquid subcooling of 40 K and liquid velocity of 0.5 m/s for a small heating surface of 10 mm×10 mm which is placed at the bottom surface of horizontal rectangular channel. The high pressure in the channel is observed at collapse of the coalescing bubbles and it is closely related the size of coalescing bubbles. Periodic pressure waves are observed in MEB and the heat flux increases linearly in proportion to the pressure frequency. The frequency is considered the frequency of liquid-solid exchange on the heating surface. For the large sized heating surface of 50 mm length×20 mm width, the maximum heat flux obtained is 500 W/cm2 (5 MW/m2) at liquid subcooling of 40 K and liquid velocity of 0.5 m/s. This is considerably higher heat flux than the conventional cooling limit in power electronics. It is difficult to remove the high heat flux by MEB for a longer heating surface than 50 mm by single channel type. A model of advanced cooling device is introduced for power electronics by subcooled flow boiling with impinging jets. Themaxumum cooling heat flux is 500 W/cm2 (5 MW/m2). Microbubble emission boiling is useful for a high heat flux transport technology in future power electronics used in a fuel-cell power plant and a space facility.

  1. Design of Tomato Drying System by Utilizing Brine Geothermal

    Science.gov (United States)

    Afuar, W.; Sibarani, B.; Abdurrahman, G.; Hendrarsakti, J.

    2016-09-01

    Cultivation of tomato plants in Indonesia has been started since 1961.Tomatoes generally will rot in three days if left on storage. Moreover, low quality tomatoes have cheaper price. After harvested, tomatoes need to be treated by drying process so it can last longer. Energy for drying tomatoes can be obtained by utilizing heat from geothermal brine. Purpose of this research is to design a tomato drying system by extracting heat of geothermal brine from separator with certain flow rate to heat up water by using a heat exchanger. Furthermore, this water will be used to heat up the surrounding air which is circulated by blower system to heat up the tomatoes chamber. Tomatoes drying process needs temperature range of 50-70°C to evaporate water content from 95.7% to 26%. After that treatment, the tomatoes are expected to have better durability. The objective of this study is to determine the quantity of hot brine which is needed for drying tomatoes and to design a drying system so that tomatoes can last longer.

  2. Uranium(VI) solubility in carbonate-free WIPP brine

    Energy Technology Data Exchange (ETDEWEB)

    Lucchini, J.F.; Borkowski, M.; Richmann, M.K.; Reed, D.T. [Los Alamos National Lab. (LANL), Carlsbad, NM (United States). Earth and Environmental Sciences Div.

    2013-08-01

    The solubility of uranium(VI) was determined in WIPP-relevant brines as a function of pC{sub H+} and ionic strength, in the absence of carbonate. Carbonate concentration was below 2 x 10{sup -5} M, measured using the gas chromatography method. In the absence of carbonate, the uranium(VI) solubilities were about x 10{sup -6} M in GWB at pC{sub H+} {>=} 7 and about 10{sup -8}-10{sup -7} M in ERDA-6 brine at pC{sub H+} {>=} 8. Solubility of uranium(VI) was also measured in NaCl media at the same levels as in ERDA-6 brine. The data established a uranium solubility that was 10-100 times lower than published results from Diaz-Arocas and Grambow, and they are in good agreement with modeling results and other literature data. In the absence of carbonate, hydrolysis was the main complexation and precipitation mechanisms for uranium(VI) solubility at high ionic strength and pC{sub H+} {>=} 7. However, the effect of borate complexation was noticeable at pC{sub H+} {proportional_to} 8-9. (orig.)

  3. Brine shrimp cytotoxic activities of Hippophae rhamnoides Linn leaves extracts

    Institute of Scientific and Technical Information of China (English)

    JavidAli; BashirAhmad

    2015-01-01

    Objective: To evaluate brine shrimp lethality assay of solvent extracts (aqueous, methanol, ethanol, acetone, ethyl acetate, chloroform and n-hexane) of Hippophae rhamnoides (H. rhamnoides) leaves. Methods: Brine shrimp cytotoxicity assay was used to assess the cytotoxic potential of H. rhamnoides leaves extracts. Three vials for concentration of each extract were made and 10 shrimps per vial (30 shrimps per dilution) were transferred to specific concentration of each extract. Results: The mortality of aqueous extract was 46.7%, methanol extract was 46.7%, ethanolic extract was 50.0%, ethyl acetate was 26.7%, acetone extract was 33.3%, chloroform extract was 40.0% and n-hexane extract was 33.3%. The lowest LD50 was found in methanol extracts (1199.97 µg/mL). Brine shrimp cytotoxicity of tested extracts of H. rhamnoides showed that mortality rate was concentration dependent. Conclusions: It is concluded that bioactive components are present in all leaves extracts of H. rhamnoides, which could be accounted for its pharmacological effects. Thus, the results support the uses of this plant species in traditional medicine.

  4. Heat Transfer in Boiling Dilute Emulsion with Strong Buoyancy

    Science.gov (United States)

    Freeburg, Eric Thomas

    Little attention has been given to the boiling of emulsions compared to that of boiling in pure liquids. The advantages of using emulsions as a heat transfer agent were first discovered in the 1970s and several interesting features have since been studied by few researchers. Early research focuses primarily on pool and flow boiling and looks to determine a mechanism by which the boiling process occurs. This thesis looks at the boiling of dilute emulsions in fluids with strong buoyant forces. The boiling of dilute emulsions presents many favorable characteristics that make it an ideal agent for heat transfer. High heat flux electronics, such as those seen in avionics equipment, produce high heat fluxes of 100 W/cm2 or more, but must be maintained at low temperatures. So far, research on single phase convection and flow boiling in small diameter channels have yet to provide an adequate solution. Emulsions allow the engineer to tailor the solution to the specific problem. The fluid can be customized to retain the high thermal conductivity and specific heat capacity of the continuous phase while enhancing the heat transfer coefficient through boiling of the dispersed phase component. Heat transfer experiments were carried out with FC-72 in water emulsions. FC-72 has a saturation temperature of 56 °C, far below that of water. The parameters were varied as follows: 0% ≤ epsilon ≤ 1% and 1.82 x 1012 ≤ RaH ≤ 4.42 x 1012. Surface temperatures along the heated surface reached temperature that were 20 °C in excess of the dispersed phase saturation temperature. An increase of ˜20% was seen in the average Nusselt numbers at the highest Rayleigh numbers. Holography was used to obtain images of individual and multiple FC-72 droplets in the boundary layer next to the heated surface. The droplet diameters ranged from 0.5 mm to 1.3 mm. The Magnus effect was observed when larger individual droplets were injected into the boundary layer, causing the droplets to be pushed

  5. Hysteresis of boiling for different tunnel-pore surfaces

    Directory of Open Access Journals (Sweden)

    Pastuszko Robert

    2015-01-01

    Full Text Available Analysis of boiling hysteresis on structured surfaces covered with perforated foil is proposed. Hysteresis is an adverse phenomenon, preventing high heat flux systems from thermal stabilization, characterized by a boiling curve variation at an increase and decrease of heat flux density. Experimental data were discussed for three kinds of enhanced surfaces: tunnel structures (TS, narrow tunnel structures (NTS and mini-fins covered with the copper wire net (NTS-L. The experiments were carried out with water, R-123 and FC-72 at atmospheric pressure. A detailed analysis of the measurement results identified several cases of type I, II and III for TS, NTS and NTS-L surfaces.

  6. Oxomemazine hydro-chloride.

    Science.gov (United States)

    Siddegowda, M S; Butcher, Ray J; Akkurt, Mehmet; Yathirajan, H S; Ramesh, A R

    2011-08-01

    IN THE TITLE COMPOUND [SYSTEMATIC NAME: 3-(5,5-dioxo-phen-othia-zin-10-yl)-N,N,2-trimethyl-propanaminium chloride], C(18)H(23)N(2)O(2)S(+)·Cl(-), the dihedral angle between the two outer aromatic rings of the phenothia-zine unit is 30.5 (2)°. In the crystal, the components are linked by N-H⋯Cl and C-H⋯Cl hydrogen bonds and C-H⋯π inter-actions.

  7. Effect of iron cation on geochemical trapping of CO2 in brine

    Science.gov (United States)

    Liu, Qi; Maroto-Valer, Mercedes

    2014-05-01

    Carbon dioxide sequestration using brines has emerged as a promising technology to mitigate the adverse impacts of climate change due to its large storage capacity and favorable chemistries. However, the permanent storage (mineral trapping) of CO2 in brines takes significantly long periods of time as the formation and precipitation of carbonates is very slow .[1]. The main parameters reported to effect on mineral trapping of CO2 sequestration in brines are brine composition, brine pH, system temperature and pressure.[2, 3]. It is suggested that the precipitation of mineral carbonates is mostly dependent on brine pH. Previous studies by the authors concluded that iron in natural brines causes pH instability, but it was not ascertained whether ferric iron or ferrous iron caused pH instability .[4]. Accordingly, the aim of this project is to study synthetic brines mimicking the major ions found in natural brines and including different concentrations of ferric and ferrous iron. Three brines were prepared, as follows: Brine 1 was prepared with ferric Fe3+ iron, Brine 2 prepared with ferrous Fe2+ iron and Brine 3 prepared with no iron. A series of pH stability studies and carbonation reactions were conducted using the above three brines. It is concluded that the ferrous iron causes pH instability, while ferric iron might promote carbonate precipitation. .1. Garcia, S., et al., Sequestration of non-pure carbon dioxide streams in iron oxyhydroxide-containing saline repositories. International Journal of Greenhouse Gas Control, 2012. 7: p. 89-97. 2. Liu, Q. and M.M. Maroto-Valer, Investigation of the pH effect of a typical host rock and buffer solution on CO 2 sequestration in synthetic brines. Fuel Processing Technology, 2010. 91(10): p. 1321-1329. 3. Liu, Q. and M.M. MarotoValer, Parameters affecting mineral trapping of CO2 sequestration in brines. Greenhouse Gases: Science and Technology, 2011. 1(3): p. 211-222. 4. Druckenmiller, M.L. and M.M. Maroto-Valer, Carbon

  8. Acute toxicity, brine shrimp cytotoxicity and relaxant activity of fruits of callistemon citrinus curtis

    Directory of Open Access Journals (Sweden)

    Shah Ismail

    2011-10-01

    Full Text Available Abstract Background Callistemon citrinus Curtis belongs to family Myrtaceae that has a great medicinal importance. In our previous work, fruits of Callistemon citrinus were reported to have relaxant (antispasmodic activity. The current work describes the screening of fractions of the crude methanol extract for tracing spasmolytic constituents so that it shall help us for isolation of bioactive compounds. Acute toxicity and brine shrimp cytotoxicity of crude methanol extract are also performed to standardize it. Methods The crude methanol extract was obtained by maceration with distilled water (500 ml three times and fractionated successively with n-hexane, chloroform, ethyl acetate and n-butanol (300 ml of each solvent. Phytochemical analysis for crude methanol extract was performed. Acute toxicity studies were performed in mice. Brine shrimp cytotoxicity studies were performed to determine its cytotoxicity and standardize it. In other series of experiments, rabbits' jejunum preparations were used in screening for possible relaxant activities of various fractions. They were applied in concentrations of 0.01, 0.03, 0.1, 0.3, 1.0, 3.0, 5.0 and 10.0 mg/ml on spontaneous rabbits' jejunum preparations. In similar fashion, fractions were also tested on KCl (80 mM -induced contractions. Calcium chloride curves were constructed in K-rich Tyrode's solution. The effects of various fractions were tested on calcium chloride curves at concentrations 1.0, 3.0, 5.0 and 10.0 mg/ml. Curves of verapamil used as reference drug at concentration 0.1 μM and 0.3 μM were also constructed. The curves were compared with their respective controls for possible right shift. Results Methanol extract tested strongly positive for saponins and tannins. However, it tested mild positive for presence of proteins, amino acids, carbohydrates and phenolic compounds. LD50 value for crude methanol extract is 476.25 ± 10.3 (470-481, n = 4 mg/ml. Similarly, EC50 value for brine shrimp

  9. Pressurized brines in continental Antarctica as a possible analogue of Mars

    Science.gov (United States)

    Forte, Emanuele; Dalle Fratte, Michele; Azzaro, Maurizio; Guglielmin, Mauro

    2016-09-01

    Interest in brines in extreme and cold environments has recently increased after they have been found on Mars. Those brines can be potential new subsurface habitats for peculiar ecosystems. In the McMurdo Dry Valleys of the Antarctic, the best analogue for Mars conditions, only a few cases of brines have been identified in some perennially frozen lakes and in one case in an underground aquifer. Here, we present the occurrence of pressurized brines in a shallow perennially ice-covered lake south of 70°S in an ice-free area of Victoria Land, Antarctica. For the first time, we also imaged, by means of ground penetrating radar data, the existence of a pingo-like-feature (PLF) formed by the extrusion of brines, which has also been confirmed by borehole evidence. Those brines are fed by an underground talik external to the lake basin, enhancing the possibility of unexploited ecosystems that could find an analogue in Martian environments.

  10. Ionic strength dependence of the oxidation of SO2 by H2O2 in sodium chloride particles

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Hashim M.; Iedema, Martin J.; Yu, Xiao-Ying; Cowin, James P.

    2014-06-20

    The reaction of sulfur dioxide and hydrogen peroxide in the presence of deliquesced (>75% RH) sodium particles was studied by utilizing a crossflow-mini reactor. The reaction kinetics was followed by observing chloride depletion in particles by computer-controlled scanning electron microscope with energy dispersive X-ray analysis, namely SEM/EDX. The reactions take place in concentrated mixed salt brine aerosols, for which no complete kinetic equilibrium data previously existed. We measured the Henry’s law solubility of H2O2 to close that gap. We also calculated the reaction rate as the particle transforms continuously from concentrated NaCl brine to eventually a mixed NaHSO4 plus H2SO4 brine solution. The reaction rate of the SO2 oxidation by H2O2 was found to be influenced by the change in ionic strength as the particle undergoes compositional transformation, following closely the dependence of the third order rate constant on ionic strength as predicted rates using previously established rate equations. This is the first study that has measured the ionic strength dependence of sulfate formation (in non-aqueous media) from oxidation of mixed salt brine aerosols in the presence of H2O2. It also gives the first report of the Henry’s law constant of H2O2 dependence on ionic strength.

  11. A Study of the Influence of Solid Particles on Boiling Hysteresis

    Institute of Scientific and Technical Information of China (English)

    M.H.Shi; J.Ma

    1992-01-01

    Experiments have been performed to determine the effects on boiling hysteresis of locally fluidized particles contained in a liquid that serves as coolant for electronic equipment.The results show that Iocally fluidized particles can diminish boiling hysteresis.

  12. 76 FR 14437 - Economic Simplified Boiling Water Reactor Standard Design: GE Hitachi Nuclear Energy; Issuance of...

    Science.gov (United States)

    2011-03-16

    ... From the Federal Register Online via the Government Publishing Office ] NUCLEAR REGULATORY COMMISSION Economic Simplified Boiling Water Reactor Standard Design: GE Hitachi Nuclear Energy; Issuance of... GE Hitachi Nuclear Energy (GEH) for the economic simplified boiling water reactor (ESBWR)...

  13. 77 FR 3009 - Knowledge and Abilities Catalog for Nuclear Power Plant Operators: Advanced Boiling Water Reactors

    Science.gov (United States)

    2012-01-20

    ... From the Federal Register Online via the Government Publishing Office NUCLEAR REGULATORY COMMISSION Knowledge and Abilities Catalog for Nuclear Power Plant Operators: Advanced Boiling Water Reactors..., ``Knowledge and Abilities Catalog for Nuclear Power Plant Operators: Advanced Boiling Water Reactors.''...

  14. Potentials of converting microalgae into brine shrimp Artemia

    OpenAIRE

    Sorgeloos, P.

    1985-01-01

    High densities of brine shrimp Artemia can be cultured in flow-through systems using the effluent of microalgae cultures as a combined source of culture medium and food. It has been proven at the "St. Croix Artificial Upwelling Mariculture Project" that in comparison with the fast growing clam Tapes japonica, brine shrimp assure a much more efficient conversion of plant into animal biomass. It appears from the given examples that microalgae conversion into brine shrimp Artemia offers efficien...

  15. Effect of whey protein concentrate and sodium chloride addition plus tumbling procedures on technological parameters, physical properties and visual appearance of sous vide cooked beef.

    Science.gov (United States)

    Szerman, N; Gonzalez, C B; Sancho, A M; Grigioni, G; Carduza, F; Vaudagna, S R

    2007-07-01

    Beef muscles cooked by the sous vide system were evaluated for the effects of pre-injection tumbling, brine addition and post-injection tumbling on technological parameters, physical properties, visual appearance and tissue microstructure. The muscles were injected at 120% (over original weight) with a brine formulated to give a concentration of 3.5% whey protein concentrate and 0.7% sodium chloride on an injected raw product basis. Pre-injection tumbling did not affect most of the evaluated parameters. Brine addition reduced significantly the cooking and total weight losses. Total weight loss was 7.2% for injected muscles, and significantly higher (28.2%) for non-injected ones. Brine incorporation increased pH and reduced shear force values of cooked muscles. Extended post-injection tumbling (5rpm-10h) improved brine distribution and visual appearance, and also diminished the shear force values of cooked muscles. However, this treatment increased the weight losses of post-injection tumbling and cooking-pasteurization stages.

  16. Geochemical and hydrologic considerations and the use of enthalpy-chloride diagrams in the prediction of underground conditions in hot-spring systems

    Science.gov (United States)

    Fournier, R.O.

    1979-01-01

    Thermal water ascending in a hot-spring system may cool by conduction of heat to the surrounding rock, by boiling, by mixing with cooler water, or by a combination of these processes. Complete or partial chemical reequilibration may occur as a result of this cooling. In spite of these complexities, in many places chemical compositions of hot-spring waters may be used to estimate underground conditions. A plot of enthalpy versus chloride is particularly useful for determining underground temperatures, salinities, and boiling and mixing relations. The utility of this approach is illustrated using hot-spring composition data from Cerro Prieto, Mexico, Orakeikorako, New Zealand, and Yellowstone National Park, Wyoming. ?? 1979.

  17. Boiling heat transfer and droplet spreading of nanofluids.

    Science.gov (United States)

    Murshed, S M Sohel; de Castro, C A Nieto

    2013-11-01

    Nanofluids- a new class of heat transfer fluids have recently been a very attractive area of research due to their fascinating thermophysical properties and numerous potential benefits and applications in many important fields. However, there are many controversies and inconsistencies in reported arguments and experimental results on various thermal characteristics such as effective thermal conductivity, convective heat transfer coefficient and boiling heat transfer rate of nanofluids. As of today, researchers have mostly focused on anomalous thermal conductivity of nanofluids. Although investigations on boiling and droplet spreading are very important for practical application of nanofluids as advanced coolants, considerably fewer efforts have been made on these thermal features of nanofluids. In this paper, recent research and development in boiling heat transfer and droplet spreading of nanofluids are reviewed together with summarizing most related patents on nanofluids published in literature. Review reveals that despite some inconsistent results nanofluids exhibit significantly higher boiling heat transfer performance compared to their base fluids and show great promises to be used as advanced heat transfer fluids in numerous applications. However, there is a clear lack of in-depth understanding of heat transport mechanisms during phase change of nanofluids. It is also found that the nanofluids related patents are limited and among them most of the patents are based on thermal conductivity enhancement and synthesising processes of specific type of nanofluids.

  18. Measuring radon reduction in xenon boil-off gas

    Energy Technology Data Exchange (ETDEWEB)

    Bruenner, Stefan; Cichon, Dominick; Lindemann, Sebastian; Marrodan Undagoitia, Teresa; Simgen, Hardy [MPIK, Heidelberg (Germany)

    2016-07-01

    {sup 222}Rn, which originates from the decay of primordial {sup 238}U, is one of the major background sources for ultra-low background noble gas detectors. One of them is XENON1T, which is a dark matter direct detection experiment looking for hypothetical weakly interacting massive particles (WIMPs). It uses liquid xenon (LXe) as a detection medium and aims to be sensitive to spin-independent WIMP-nucleon cross-sections of σ∝2.10{sup -47} cm{sup 2} at a WIMP mass of ∝50 GeV/c{sup 2}. To achieve this goal, radon activity inside the detector must be limited to a few mBq/kg. One possible way for reducing the concentration of {sup 222}Rn inside such an LXe detector is using the so-called ''boil-off method''. It takes advantage of the fact, that the radon concentration in boil-off xenon is smaller compared to the concentration in the liquid xenon from which the boil-off xenon evaporated. This can be understood by the different vapor pressures of radon and xenon. In this talk, tests conducted at the MPIK are outlined which probe the feasibility and effectiveness of the boil-off method. The results prove, that a reduction of the radon concentration can indeed be achieved. In addition, an outlook for possible future applications of this technique is given.

  19. Boiling process in oil coolers on porous elements

    Directory of Open Access Journals (Sweden)

    Genbach Alexander A.

    2016-01-01

    Full Text Available Holography and high-speed filming were used to reveal movements and deformations of the capillary and porous material, allowing to calculate thermo-hydraulic characteristics of boiling liquid in the porous structures. These porous structures work at the joint action of capillary and mass forces, which are generalised in the form of dependences used in the calculation for oil coolers in thermal power plants (TPP. Furthermore, the mechanism of the boiling process in porous structures in the field of mass forces is explained. The development process of water steam formation in the mesh porous structures working at joint action of gravitational and capillary forces is investigated. Certain regularities pertained to the internal characteristics of boiling in cells of porous structure are revealed, by means of a holographic interferometry and high-speed filming. Formulas for calculation of specific thermal streams through thermo-hydraulic characteristics of water steam formation in mesh structures are obtained, in relation to heat engineering of thermal power plants. This is the first calculation of heat flow through the thermal-hydraulic characteristics of the boiling process in a reticulated porous structure obtained by a photo film and holographic observations.

  20. Treatment of cork boiling wastewater using chemical oxidation and biodegradation.

    Science.gov (United States)

    Dias-Machado, Manuela; Madeira, Luis M; Nogales, Balbina; Nunes, Olga C; Manaia, Célia M

    2006-06-01

    Three cultures were enriched from cork boiling wastewater using tannic acid as the selective carbon substrate, at 25 degrees C and pH 7.2, 25 degrees C and pH 4.7 and 50 degrees C and pH 4.7. The enrichment culture obtained at neutral pH was composed of five culturable isolates, whereas from each acidic enrichment two bacterial strains were isolated. Mesophilic isolates were Gram negative bacteria belonging to the genera Klebsiella, Pseudomonas, Stenotrophomonas and Burkholderia. Thermophilic isolates were members of the genus Bacillus. Despite the capability of the enrichment cultures to use tannic acid as single carbon and energy source, those cultures were unable to reduce the total polyphenols or the total organic carbon content of cork boiling wastewater. In order to increase the bioavailability of the organic carbon in cork boiling wastewater, biodegradation was preceded by Fenton oxidation. It was demonstrated that the combined process, using small amounts of Fenton reagents and biodegradative inoculum added almost simultaneously to cork boiling wastewater, leads to TOC reductions of more than 90%.

  1. How long does it take to boil an egg? Revisited

    Energy Technology Data Exchange (ETDEWEB)

    Buay, D [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Foong, S K [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Kiang, D [Department of Physics, Chinese University of Hong Kong, Shatin, New Territories, Hong Kong (China); Kuppan, L [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Centre for Research in Pedagogy and Practice, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Liew, V H [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore)

    2006-01-01

    How long does it take to boil an egg? Theoretical prediction, based on a simple adaptation of the solution to the exact thermal diffusion equation for a sphere, is consistent with experiments. The experimental data are also used to estimate an average value for the thermal diffusivity of an egg.

  2. Experimental demonstration of contaminant removal from fractured rock by boiling.

    Science.gov (United States)

    Chen, Fei; Liu, Xiaoling; Falta, Ronald W; Murdoch, Lawrence C

    2010-08-15

    This study was conducted to experimentally demonstrate removal of a chlorinated volatile organic compound from fractured rock by boiling. A Berea sandstone core was contaminated by injecting water containing dissolved 1,2-DCA (253 mg/L) and sodium bromide (144 mg/L). During heating, the core was sealed except for one end, which was open to the atmosphere to simulate an open fracture. A temperature gradient toward the outlet was observed when boiling occurred in the core. This indicates that steam was generated and a pressure gradient developed toward the outlet, pushing steam vapor and liquid water toward the outlet. As boiling occurred, the concentration of 1,2-DCA in the condensed effluent peaked up to 6.1 times higher than the injected concentration. When 38% of the pore volume of condensate was produced, essentially 100% of the 1,2-DCA was recovered. Nonvolatile bromide concentration in the condensate was used as an indicator of the produced steam quality (vapor mass fraction) because it can only be removed as a solute, and not as a vapor. A higher produced steam quality corresponds to more concentrated 1,2-DCA removal from the core, demonstrating that the chlorinated volatile compound is primarily removed by partitioning into vapor phase flow. This study has experimentally demonstrated that boiling is an effective mechanism for CVOC removal from the rock matrix.

  3. Investigation Status of Heat Exchange while Boiling Hydrocarbon Fuel

    Directory of Open Access Journals (Sweden)

    D. S. Obukhov

    2006-01-01

    Full Text Available The paper contains analysis of heat exchange investigations while boiling hydrocarbon fuel. The obtained data are within the limits of the S.S. Kutateladze dependence proposed in 1939. Heat exchange at non-stationary heat release has not been investigated. The data for hydrocarbon fuel with respect to critical density of heat flow are not available even for stationary conditions.

  4. A Review of Boiling Heat Transfer Processes at High Heat Flux

    Science.gov (United States)

    1991-04-01

    liquid metals) which can lead to explosive boiling (known as bumping) that can lead to structural damage to hardware. 3 Transition boiling occurs between...to initiate boiling, in some cases having an explosive transition that can cause structural damage to hardware. A thorough understanding of boiling...graphical correlations for the pressure drops encountered in their experiments. About the same time, Staub and Walmet (Ref. 173) identified the two regions

  5. Transport of Pb and Zn by carboxylate complexes in basinal ore fluids and related petroleum-field brines at 100°C: the influence of pH and oxygen fugacity

    Directory of Open Access Journals (Sweden)

    Giordano Thomas H

    2002-09-01

    can mobilize up to 3% of the total Pb and up to 1.3% of the total Zn as carboxylate complexes. Furthermore, these percentages, under the most favorable conditions, correspond to approximately 1 to 100 ppm of these metals in solution; concentrations that are adequate to form economic deposits of these metals. However, the field evidence suggests that all of these optimum conditions for carboxylate complexation are rarely met at the same time. A comparison of the composite ore fluid compositions from this study and modern brine data shows that the ore brines, corresponding to log –pH conditions based on the Anderson (1975 and Giordano (1994 model fluids, are similar in many respects to modern, high trace-metal petroleum-field brines. The principal differences between modern high trace-metal brines and the composite ore fluids of Anderson (1975 and Giordano (1994 relate to their carboxylate anion content. The reported concentrations of monocarboxylate anions (∑monocbx and dicarboxylate anions (Edicbx in high trace-metal petroleum-field brines (-1 and -1, respectively are significantly lower than the concentrations assumed in the modelled brines of this study (∑monocbx = 7 700 mg L-1 and ∑dicbx = 300 mg L-1. There are also major differences in the corresponding total chloride to carboxylate ratio (∑mCl/∑mcbx and monocarboxylate to dicarboxylate ratio (∑mmonocbx/∑mdicbx. Modern high trace-metal brines have much higher ∑mCl/∑mcbx values and, therefore, the contribution of carboxylate complexes to the total Pb and Zn content in these modern brines is likely to be significantly less than the 1 to 3 percent for the composite ore fluids of Anderson (1975 and Giordano (1994. The composite ore-brine based on the Giordano and Barnes (1981 MVT ore fluid is comparable to the high salinity (> 170 000 mg L-1 TDS subset of modern brines characterized by low trace-metal content and high total reduced sulfur (∑H2S. A comparison of the Sverjensky (1984 composite ore-brine

  6. Nucleate Pool Boiling Experiments (NPBX) on the International Space Station

    Science.gov (United States)

    Dhir, Vijay Kumar; Warrier, Gopinath R.; Aktinol, Eduardo; Chao, David; Eggers, Jeffery; Sheredy, William; Booth, Wendell

    2012-11-01

    During the period of March-May 2011, a series of boiling experiments was carried out in the Boiling Experimental Facility (BXF) located in the Microgravity Science Glovebox (MSG) of the International Space Station (ISS). The BXF Facility was carried to ISS on Space Shuttle Mission STS-133 on February 24, 2011. Nucleate Pool Boiling Experiment (NPBX) was one of the two experiments housed in the BXF. Results of experiments on single bubble dynamics (e.g., inception and growth), multiple bubble dynamics (lateral merger and departure, if any), nucleate pool boiling heat transfer, and critical heat flux are described. In the experiments Perfluoro-n-hexane was used as the test liquid. The system pressure was varied from 51 to 243 kPa, pool temperature was varied from 30° to 59°C, and test surface temperature was varied from 40° to 80°C. The test surface was a polished aluminum disc (1 mm thick, 89.5 mm in diameter) heated from below with strain gage heaters. Five cylindrical cavities were formed on the surface with four cavities located at the corners of a square and one in the middle. During experiments the magnitude of mean gravity level normal to the heater surface varied from 1.2 × 10 - 7g e to 6 × 10 - 7g e . The results of the experiments show that a single bubble continues to grow to occupy the size of the chamber without departing from the heater surface. During lateral merger of bubbles, at high superheats a large bubble may lift off from the surface but continues to hover near the surface. Neighboring bubbles are continuously pulled into the large bubble. At low superheats bubbles at neighboring sites simply merge to yield a larger bubble. The larger bubble mostly locates in the middle of the heated surface and serves as a vapor sink. The latter mode continues to persist when boiling is occurring all over the heater surface. Heat fluxes for steady state nucleate boiling and critical heat fluxes are found to be much lower than those obtained under earth

  7. Chemical and isotopic characteristics of brines from three oil- and gas-producing sandstones in eastern Ohio, with applications to the geochemical tracing of brine sources

    Science.gov (United States)

    Breen, K.J.; Angelo, Clifford G.; Masters, Robert W.; Sedam, Alan C.

    1985-01-01

    Chemical and isotopic characteristics of selected inorganic constituents are reported for brines from the Berea Sandstone of Mississippian age, the Clinton sandstone, Albion Sandstone of Silurian age, and the Rose Run formation of Cambrian and Ordovician age in 24 counties in eastern Ohio. Ionic concentrations of dissolved constituents in brines from these formations generally fall in the following ranges (in millimoles per kilogram of brine): Na, Cl > 1,000; 100 Al, I, HCO3, SiO2 Mg, Na, Cl, K, SO4 and Br, and mean values of density and dissolved solids are significantly different at the 95-percent confidence level in each formation. Only potassium has a unique concentration range in each formation. Selected concentration ratios are identified as potential indicators for geochemical tracing of brines having some history of dilution. The k:Na ratios work best for identifying the source formation of an unidentified brine. Isotopic characteristics of hydrogen and oxygen indicate a meteoric origin for the water matrix of the brines. Sulfur isotopes may have utility for differentiating brines from oxidizing ground water.

  8. A Study of Nucleate Boiling with Forced Convection in Microgravity

    Science.gov (United States)

    Merte, Herman, Jr.

    1999-01-01

    The ultimate objective of basic studies of flow boiling in microgravity is to improve the understanding of the processes involved, as manifested by the ability to predict its behavior. This is not yet the case for boiling heat transfer even in earth gravity, despite the considerable research activity over the past 30 years. The elements that constitute the nucleate boiling process - nucleation, growth, motion, and collapse of the vapor bubbles (if the bulk liquid is subcooled) - are common to both pool and flow boiling. It is well known that the imposition of bulk liquid motion affects the vapor bubble behavior relative to pool boiling, but does not appear to significantly influence the heat transfer. Indeed, it has been recommended in the past that empirical correlations or experimental data of pool boiling be used for design purposes with forced convection nucleate boiling. It is anticipated that such will most certainly not be possible for boiling in microgravity, based on observations made with pool boiling in microgravity. In earth gravity buoyancy will act to remove the vapor bubbles from the vicinity of the heater surface regardless of how much the imposed bulk velocity is reduced, depending, of course, on the geometry of the system. Vapor bubbles have been observed to dramatically increase in size in pool boiling in microgravity, and the heat flux at which dryout took place was reduced considerably below what is generally termed the critical heat flux (CHF) in earth gravity, depending on the bulk liquid subcooling. However, at heat flux levels below dryout, the nucleate pool boiling process was enhanced considerably over that in earth gravity, in spite of the large vapor bubbles formed in microgravity and perhaps as a consequence. These large vapor bubbles tended to remain in the vicinity of the heater surface, and the enhanced heat transfer appeared to be associated with the presence of what variously has been referred to as a liquid microlayer between the

  9. Bubble and boundary layer behaviour in subcooled flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Maurus, Reinhold; Sattelmayer, Thomas [Lehrstuhl fuer Thermodynamik, Technische Universitaet Muenchen, 85747 Garching (Germany)

    2006-03-15

    Subcooled flow boiling is a commonly applied technique for achieving efficient heat transfer. In the study, an experimental investigation in the nucleate boiling regime was performed for water circulating in a closed loop at atmospheric pressure. The horizontal orientated test-section consists of a rectangular channel with a one side heated copper strip and good optical access. Various optical observation techniques were applied to study the bubble behaviour and the characteristics of the fluid phase. The bubble behaviour was recorded by the high-speed cinematography and by a digital high resolution camera. Automated image processing and analysis algorithms developed by the authors were applied for a wide range of mass flow rates and heat fluxes in order to extract characteristic length and time scales of the bubbly layer during the boiling process. Using this methodology, the bubbles were automatically analysed and the bubble size, bubble lifetime, waiting time between two cycles were evaluated. Due to the huge number of observed bubbles a statistical analysis was performed and distribution functions were derived. Using a two-dimensional cross-correlation algorithm, the averaged axial phase boundary velocity profile could be extracted. In addition, the fluid phase velocity profile was characterised by means of the particle image velocimetry (PIV) for the single phase flow as well as under subcooled flow boiling conditions. The results indicate that the bubbles increase the flow resistance. The impact on the flow exceeds by far the bubbly region and it depends on the magnitude of the boiling activity. Finally, the ratio of the averaged phase boundary velocity and of the averaged fluid velocity was evaluated for the bubbly region. (authors)

  10. Analysis of Abnormal Phenomena in High Magnesium Boron Containing Salt Brine System%高镁含硼盐卤体系反常现象解析

    Institute of Scientific and Technical Information of China (English)

    乌志明; 崔香梅; 郑绵平

    2012-01-01

    Such phenomena as "supersaturated solubility", "salt formation by dilution" and "solubility increase of homonymy ion" exist in high magnesium boron containing salt brine system. Our research indicates that the magnesium chloride solution is neutral with medium or low concentration. It shows acidic property with high concentration and the pH value is lower than 4.5 when saturated. But many types of magnesium borate minerals are alkaline ones with pH value higher than 8.0. We know in general acid and base could hardly co-exist in an aqueous solution, but magnesium borate and magnesium chloride in high magnesium boron containing salt brine system do owing to the possession of the homonymy ion. The above mentioned abnormal phenomena can be satisfactorily interpreted with special acidity change of magnesium chloride solution and some related phase chemistry data.%高镁含硼盐卤体系中存在“过饱和溶解度”、“稀释成盐”和同名离子“增溶”等反常现象.研究发现:氯化镁溶液在中低浓度时显中性,在高浓度时显酸性,饱和时pH值小于4.5.而各种镁硼酸盐基本都是pH值大于8.0的碱性矿物.水溶液中酸碱难共存,但镁硼酸盐与氯化镁却因具有相同离子而能够在高镁含硼盐卤体系中共存.结合氯化镁溶液特殊酸度变化规律与相关相化学数据可较圆满的解释高镁含硼盐卤体系中的反常现象.

  11. Benzalkonium chloride and glaucoma.

    Science.gov (United States)

    Rasmussen, Carol A; Kaufman, Paul L; Kiland, Julie A

    2014-01-01

    Glaucoma patients routinely take multiple medications, with multiple daily doses, for years or even decades. Benzalkonium chloride (BAK) is the most common preservative in glaucoma medications. BAK has been detected in the trabecular meshwork (TM), corneal endothelium, lens, and retina after topical drop installation and may accumulate in those tissues. There is evidence that BAK causes corneal and conjunctival toxicity, including cell loss, disruption of tight junctions, apoptosis and preapoptosis, cytoskeleton changes, and immunoinflammatory reactions. These same effects have been reported in cultured human TM cells exposed to concentrations of BAK found in common glaucoma drugs and in the TM of primary open-angle glaucoma donor eyes. It is possible that a relationship exists between chronic exposure to BAK and glaucoma. The hypothesis that BAK causes/worsens glaucoma is being tested experimentally in an animal model that closely reflects human physiology.

  12. Chloride on the Move

    KAUST Repository

    Li, Bo

    2017-01-09

    Chloride (Cl−) is an essential plant nutrient but under saline conditions it can accumulate to toxic levels in leaves; limiting this accumulation improves the salt tolerance of some crops. The rate-limiting step for this process – the transfer of Cl− from root symplast to xylem apoplast, which can antagonize delivery of the macronutrient nitrate (NO3−) to shoots – is regulated by abscisic acid (ABA) and is multigenic. Until recently the molecular mechanisms underpinning this salt-tolerance trait were poorly defined. We discuss here how recent advances highlight the role of newly identified transport proteins, some that directly transfer Cl− into the xylem, and others that act on endomembranes in ‘gatekeeper’ cell types in the root stele to control root-to-shoot delivery of Cl−.

  13. Electrically Conducting, Ca-Rich Brines, Rather Than Water, Expected in the Martian Subsurface

    Science.gov (United States)

    Burt, D. M.; Knauth, L. P.

    2003-01-01

    If Mars ever possessed a salty liquid hydrosphere, which later partly evaporated and froze down, then any aqueous fluids left near the surface could have evolved to become dense eutectic brines. Eutectic brines, by definition, are the last to freeze and the first to melt. If CaC12-rich, such brines can remain liquid until temperatures below 220 K, close to the average surface temperature of Mars. In the Martian subsurface, in intimate contact with the Ca-rich basaltic regolith, NaC1-rich early brines should have reacted to become Ca-rich. Fractional crystallization (freezing) and partial melting would also drive brines toward CaC12-rich compositions. In other words, eutectic brine compositions could be present in the shallow subsurface of Mars, for the same reasons that eutectic magma compositions are common on Earth. Don Juan Pond, Antarctica, a CaC12-rich eutectic brine, provides a possible terrestrial analog, particularly because it is fed from a basaltic aquifer. Owing to their relative density and fluid nature, brines in the Martian regolith should eventually become sandwiched between ice above and salts beneath. A thawing brine sandwich provides one explanation (among many) for the young gullies recently attributed to seepage of liquid water on Mars. Whether or not brine seepage explains the gullies phenomenon, dense, CaC12-rich brines are to be expected in the deep subsurface of Mars, although they might be somewhat diluted (temperatures permitting) and of variable salt composition. In any case, they should be good conductors of electricity.

  14. Transition and separation process in brine channels formation

    Energy Technology Data Exchange (ETDEWEB)

    Berti, Alessia, E-mail: alessia.berti@unibs.it [Facoltà di Ingegneria, Università e-Campus, Via Isimbardi 10, 22060 Novedrate, CO (Italy); Bochicchio, Ivana, E-mail: ibochicchio@unisa.it [Dipartimento di Matematica, Universitá degli Studi di Salerno, Via Giovanni Paolo II, 84084 Fisciano, SA (Italy); Fabrizio, Mauro, E-mail: mauro.fabrizio@unibo.it [Dipartimento di Matematica, Università di Bologna, Piazza di Porta S. Donato, 40126 Bologna (Italy)

    2016-02-15

    In this paper, we discuss the formation of brine channels in sea ice. The model includes a time-dependent Ginzburg-Landau equation for the solid-liquid phase change, a diffusion equation of the Cahn-Hilliard kind for the solute dynamics, and the heat equation for the temperature change. The macroscopic motion of the fluid is also considered, so the resulting differential system couples with the Navier-Stokes equation. The compatibility of this system with the thermodynamic laws and a maximum theorem is proved.

  15. Isolation of Halobacterium salinarum retrieved directly from halite brine inclusions

    Energy Technology Data Exchange (ETDEWEB)

    Mormile, Melanie R.; Biesen, Michelle A.; Gutierrez, M. Carmen; Ventosa, Antonio; Pavlovich, Justin B.; Onstott, T C.; Fredrickson, Jim K.

    2003-11-01

    Halite crystals were selected from a 186m subsurface core taken from the Badwater salt pan, Death Valley, California to ascertain if halophilic Archaea and their associated 16S rDNA can survive over several tens of thousands of years. Using a combined microscope microdrill/micropipette system, fluids from brine inclusions were aseptically extracted from primary, hopper texture, halite crystals from 8 and 85 metres below the surface (mbls). U-Th disequilibrium dating indicates that these halite layers were deposited at 9600 and 97000 years before present (ybp) respectively.

  16. Zero Boil Off Cryogen Storage for Future Launchers

    Science.gov (United States)

    Valentian, D.; Plachta, D.; Kittel, P.; Hastings, L. J.; Salerno, Louis J.; Arnold, James O. (Technical Monitor)

    2001-01-01

    Zero boil off (ZBO) cryogen storage using both cryocoolers and passive insulation technologies will enable long-term exploration missions by allowing designers to optimize tankage without the need for excess cryogen storage to account for boil off. Studies of ZBO (zero boil off) have been on-going in the USA for several years. More recently, a review of the needs of advanced space propulsion took place in Europe. This showed the interest of the European community in cryogenic propulsion for planetary missions as well as the use of liquid hydrogen for large power electric propulsion (manned Mars missions). Although natural boiling could be acceptable for single leg missions, passive insulation techniques yield roughly a I% per month cryogen loss and this would not be cost effective for robotic planetary missions involving storage times greater than one year. To make economic sense, long-term exploration missions require lower tank capacity and longer storage times. Recent advances in cryocooler technology, resulting in vast improvements in both cooler efficiency and reliability, make ZBO is a clear choice for planetary exploration missions. Other, more near term applications of ZBO include boil-off reduction or elimination applied to first and upper stages of future earth-to-orbit (ETO) launchers. This would extend launch windows and reduce infrastructure costs. Successors to vehicles like Ariane 5 could greatly benefit by implementing ZBO. Zero Boil Off will only be successful in ETO launcher applications if it makes economic sense to implement. The energy cost is only a fraction of the total cost of buying liquid cryogen, the rest being transportation and other overhead. Because of this, higher boiling point cryogens will benefit more from on-board liquefaction, thus reducing the infrastructure costs. Since hydrogen requires a liquefier with at least a 17% efficiency just to break even from a cost standpoint, one approach for implementing ZBO in upper stages would

  17. Scaling of Structural and Rheological Responde of L3 Sponge Phases in the "Sweetened" Cetylpyridinium/Hexanol/Dextrose/Brine System

    Energy Technology Data Exchange (ETDEWEB)

    Porcar, L. [National Institute of Standards and Technology (NIST); Hamilton, William A [ORNL; Butler, Paul D [ORNL; Warr, G. G. [University of Sydney, Australia

    2003-01-01

    We report a study of the shear response of sponge phases in cetylpyridinium chloride (CPCl)/hexanol/brine/dextrose systems by parallel measurements of rheology and structure by small angle neutron scattering (SANS). Our measurements show that this dextrose added to the extensively studied CPCl/hexanol/brine system is taken up exclusively by the brine solvent, resulting in an equivalent CPCl/hexanol membrane structure and phase behavior for this modified system. Adding dextrose to the brine in these systems to volume fractions up to 0.4 allows us to increase the solvent viscosity by more than an order of magnitude. This lowers the cooperative membrane diffusion coefficient in this system as measured by dynamic light scattering by the same factor, resulting in a corresponding slowing of the Helfrich fluctuation dominated membrane dynamics. Our results show clear and consistent evidence of shear-induced sponge to lamellar phase transformations in these systems. Further, both the rheological and microstructural responses of these systems follow universal master curves when plotted against a rescaled applied shear {sub {gamma}}{eta}{sub s}/{phi}{sup 3}, where {phi} is the membrane volume fraction and {eta}{sub s} is the viscosity of the brine/dextrose solvent. This well-defined shear response is characterized by three distinct regimes. At low shear rates the sponge phases exhibit Newtonian flow behavior and no structural change is observed. For intermediate shear rates, the systems shear thin and SANS measurements show that the sponge phases are progressively transformed into lamellar phases with the CPCl/hexanol membrane normals aligned parallel to the velocity gradient. This continuous process and the absence of a stress plateau in the rheological measurements both rule out the existence of a biphasic state in this region and thus of a first-order transition between sponge and lamellar phases as is observed in equilibrium phase diagrams. At higher shear rates, the

  18. Development of a mechanistic model for forced convection subcooled boiling

    Science.gov (United States)

    Shaver, Dillon R.

    The focus of this work is on the formulation, implementation, and testing of a mechanistic model of subcooled boiling. Subcooled boiling is the process of vapor generation on a heated wall when the bulk liquid temperature is still below saturation. This is part of a larger effort by the US DoE's CASL project to apply advanced computational tools to the simulation of light water reactors. To support this effort, the formulation of the dispersed field model is described and a complete model of interfacial forces is formulated. The model has been implemented in the NPHASE-CMFD computer code with a K-epsilon model of turbulence. The interfacial force models are built on extensive work by other authors, and include novel formulations of the turbulent dispersion and lift forces. The complete model of interfacial forces is compared to experiments for adiabatic bubbly flows, including both steady-state and unsteady conditions. The same model is then applied to a transient gas/liquid flow in a complex geometry of fuel channels in a sodium fast reactor. Building on the foundation of the interfacial force model, a mechanistic model of forced-convection subcooled boiling is proposed. This model uses the heat flux partitioning concept and accounts for condensation of bubbles attached to the wall. This allows the model to capture the enhanced heat transfer associated with boiling before the point of net generation of vapor, a phenomenon consistent with existing experimental observations. The model is compared to four different experiments encompassing flows of light water, heavy water, and R12 at different pressures, in cylindrical channels, an internally heated annulus, and a rectangular channel. The experimental data includes axial and radial profiles of both liquid temperature and vapor volume fraction, and the agreement can be considered quite good. The complete model is then applied to simulations of subcooled boiling in nuclear reactor subchannels consistent with the

  19. Precipitation of halite from supersaline brine from Tønder formation

    DEFF Research Database (Denmark)

    Arturi, Kasia; Søgaard, Erik Gydesen

    2014-01-01

    This project deals various treatments for geothermal brine, which is a highly salty solution containing more that 50 TDS (Total Dissolved Solids). This project focuses on the brine from Tønder formation (T=73°C), which has an extraordinarily high salt content NaCl ([C] = 300-310 g/l). According...

  20. Antioxidative low molecular weight compounds in marinated herring (Clupea harengus) salt brine

    DEFF Research Database (Denmark)

    Gringer, Nina; Safafar, Hamed; du Mesnildot, Axelle;

    2016-01-01

    This study aimed at unravelling the antioxidative capacity of low molecular weight compounds (LMWC) (peptides, amino acids and phenolic acids) present in salt brines from the marinated herring production. Brines were fractionated into <10 kDa fractions using dialysis and further into 94 fractions...

  1. Laboratory monitoring of CO2 migration within brine-saturated reservoir rock though complex electrical impedance

    NARCIS (Netherlands)

    Kirichek, O.; Ghose, R.; Heller, H.K.J.

    2013-01-01

    We investigate the ability of complex electrical measurements to monitor the CO2 front propagation within brine-saturated reservoir rock. A laboratory facility has been developed to perform CO2-brine substitution experiments under reservoir conditions. In the present study, CO2 is injected into a br

  2. Geochemistry of Salado Formation brines recovered from the Waste Isolation Pilot Plant (WIPP) repository

    Energy Technology Data Exchange (ETDEWEB)

    Abitz, R.; Myers, J.; Drez, P.; Deal, D.

    1990-01-01

    Intergranular brines recovered from the repository horizon of the Waste Isolation Pilot Plant (WIPP) have major- and trace-element compositions that reflect seawater evaporation and diagenetic processes. Brines obtained from repository drill holes are heterogenous with respect to composition, but their compositional fields are distinct from those obtained from fluid inclusions in WIPP halite. The heterogeneity of brine compositions within the drill-hole population indicates a lack of mixing and fluid homogenization within the salt at the repository level. Compositional differences between intergranular (drill hole) and intragranular (fluid inclusions) brines is attributed to isolation of the latter from diagenetic fluids that were produced from dehydration reactions involving gypsum and clay minerals. Modeling of brine-rock equilibria indicates that equilibration with evaporite minerals controls the concentrations of major elements in the brine. Drill-hole brines are in equilibrium with the observed repository minerals halite, anhydrite, magnesite, polyhalite and quartz. The equilibrium model supports the derivation of drill-hole brines from near-field fluid, rather than large-scale vertical migration of fluids from the overlying Rustler or underlying Castile Formations. 13 refs., 6 figs., 6 tabs.

  3. Water Recovery from Brine in the Short and Long Term: A KSC Approach

    Science.gov (United States)

    Lunn, Griffin; Melendez, Orlando; Anthony, Steve

    2014-01-01

    KSC has spent many years researching Hollow Fiber Membrane Bioreactors as well as research encompassing: Alternate ammonia removal, Advanced oxidation, Brine purification technologies. KSC-ISRU has built an electrolysis cell for the removal of acids in ISRU mining brines. Our goal is to combine all such technologies.

  4. Improving the performance of brine wells at Gulf Coast strategic petroleum reserve sites

    Energy Technology Data Exchange (ETDEWEB)

    Owen, L.B.; Quong, R. (eds.)

    1979-11-05

    At the request of the Department of Energy, field techniques were developed to evaluate and improve the injection of brine into wells at Strategic Petroleum Reserve (SPR) sites. These wells are necessary for the disposal of saturated brine removed from salt domes where oil is being stored. The wells, which were accepting brine at 50 percent or less of their initial design rates, were impaired by saturated brine containing particulates that deposited on the sand face and in the geologic formation next to the wellbore. Corrosion of the brine-disposal pipelines and injection wells contributed to the impairment by adding significant amounts of particulates in the form of corrosion products. When tests were implemented at the SPR sites, it was found that the poor quality of injected brines was the primary cause of impaired injection; that granular-media filtration, when used with chemical pretreatment, is an effective method for removing particulates from hypersaline brine; that satisfactory injection-well performance can be attained with prefiltered brines; and that corrosion rates can be substantially reduced by oxygen-scavenging.

  5. BELL PEPPER CULTIVATION WITH BRINE FROM BRACKISH WATER DESALINATION

    Directory of Open Access Journals (Sweden)

    CARLOS EDUARDO DE MOURA ARRUDA

    2011-01-01

    Full Text Available In desalination process, besides the potable water, highly salty and pollutant water (brine is generated, which can be used for producing crops since it is carefully monitored. In order to test this hypothesis, bell pepper plants, cv. 'Margarita', were grown in coconut fiber substrate under greenhouse and were irrigated with nutrient solutions prepared with tap water, brine from desalination plant, and its dilution with tap water at 75, 50 and 25%, giving a range of electrical conductivities of the nutrient solution (ECs of 2.6, 3.1, 6.6, 10.0 and 12.2 dS m-1 after the dilutions and fertilizers addition. Completely randomized blocks design was used with 5 treatments (salinity levels of the nutrient solutions and six replications. Leaf area, number of marketable fruit, total and marketable yield were reduced with ECs increase. The marketable yield of bell pepper 'Margarita' reduced 6.3% for each unitary increase of ECs above 2.6 dS m-1 (threshold salinity and the results suggest that in hydroponic system, the reduction of marketable yield with increasing ECs is promoted by reduction of the number of fruits per plant instead of a reduction of fruit mean weight.

  6. Cyanobacterial cytotoxicity versus toxicity to brine shrimp Artemia salina.

    Science.gov (United States)

    Hisem, Daniel; Hrouzek, Pavel; Tomek, Petr; Tomšíčková, Jana; Zapomělová, Eliška; Skácelová, Kateřina; Lukešová, Alena; Kopecký, Jiří

    2011-01-01

    Heterocytous cyanobacteria from various habitats were screened for toxicity to brine shrimp Artemia salina and the murine lymphoblastic cell line Sp/2 in order to compare these two testing models for evaluation of risk posed by cyanobacteria to human health. Methanol extracts of biomass and cultivation media were tested for toxicity and selected extracts were fractionated to determine the active fraction. We found a significant toxic effect to A. salina and to Sp/2 cells in 5.2% and 31% of studied extracts, respectively. Only 8.6% of the tested strains were highly toxic to both A. salina and the Sp/2 cell line, and only two of the tested strains were toxic to A. salina and not to the murine cell line. Therefore, it is likely that the toxic effect of cyanobacterial secondary metabolites mostly targets basal metabolic pathways present in mammal cells and so is not manifested in A. salina. We conclude that it is insufficient to monitor cytotoxicity of cyanobacteria using only the brine shrimp bioassay as was usual in the past, since cytotoxicity is a more frequent feature in cyanobacteria in comparison with toxicity to A. salina. A. salina toxicity test should not be used when estimating the possible health risk for humans. We suggest that in vitro mammal cells be used for these purposes.

  7. 不同浓度盐水对鸭肉湿腌时传质动力的影响%Influence of brine concentration on mass transfer kinetics of duck during wet-curing

    Institute of Scientific and Technical Information of China (English)

    杜垒; 李艳逢; 周光宏; 徐幸莲; 王进; 肖治国; 陶明财

    2011-01-01

    Firstly , duck thigh meat were wet-cured using old brine which brined the water- boiled salted duck and other brine concentrations (5%, 15 % and 25% NaCl, w/w) following with the production process of water- boiled salted duck which was wet-curing after dry-curing ,then the changes of salt,water content and total weight were analyzed and intended to obtain the first data of mass transfer kinetics for duck thigh meat under different brine concentration and information of the basic mechanism of salted process. Results indicated that the brine concentration significantly affected the total weight changes of the duck thigh meat. The weight change and water content of the duck thigh meat increased with decreasing brine concentration, the salt content had an opposite change. 15 % NaCl(w/w) brine,the moderate salt concentration, was the most suitable for wet- curing just because of its higher process yields with high De value and lower health risks. Moreover,there were good linear relationships between total weight change and curing time, the correlation coefficients were all good. Experiments verified that the kinetics model was fit to curing process.%研究采用盐水鸭生产时使用的过饱和盐水--老卤和其他三种不同浓度的盐水(5%、15%和25%NaCl,w/w)对鸭腿肉按照盐水鸭的生产过程进行腌制,通过对腌制过程中鸭腿肉的食盐、水分和总重变化进行测定,以期获得不同盐水浓度下鸭肉的传质动力学数据,并获得腌制最适盐水浓度.结果表明,盐水浓度显著影响鸭腿肉在腌制过程中的传质变化.鸭腿肉的重量变化、水分获得都是随着盐水溶液浓度的降低而增加,盐分变化则相反.中等浓度的盐水溶液(15%NaCl,w/w)腌制的鸭肉产量较高,有较高的扩散速率--De值,对人体的损害较小.因此,较为适于用来腌制鸭肉.另外,腌制的预测模型和扩散公式计算得到的数据都有良好的线性关系,可以很好地适用于鸭腿肉的腌制实验研究.

  8. Thermal Enhanced Oil Recovery Using Geopressured-Geothermal Brine

    Energy Technology Data Exchange (ETDEWEB)

    none

    1989-12-01

    This white paper presents a unique plan for an Oil Industry-DOE cost sharing research project for Thermal Enhanced Oil Recovery (TEOR) of medium and heavy oil using geopressured-geothermal brine. This technology would provide an environmentally clean method of recovery as opposed to the burning of crude oil or natural gas used widely by the industry, but presently under scrutiny by federal and state air quality agencies, as well as provide an alternative to the very expensive operational and mechanical problems associated with heating water on the surface for injection. An example test reservoir is a shallow, small structural reservoir about 1-l/2 miles long by 1/2 mile wide. It is presently producing heavy oil (18.6 API gravity) from 5 wells, and is marginally economic. One of three nearby geopressured-geothermal wells could be re-entered and recompleted to supply about 400 F brine from 13-16,000 feet. This brine can be used to heat and drive the heavy oil. It is anticipated that about one million barrels of oil may be recovered by this project. Over 3 million barrels are estimated to be in place; only 2.7% of the oil in place has been produced. The suggested teaming arrangement includes: (1) EG&G Idaho, Inc., which presently provides technical and management support to DOE in the Gulf EG&G would supply coordination, management and Coast Geopressured-Geothermal Program. technical support to DOE for the Thermal Enhanced Oil Recovery Project. (2) A small business which would supply the field, geologic and well data, production wells, and production operation. They would cost-share the project and provide revenue from increased production (5% of increased production) to help offset DOE costs. Though DOE would cost-share brine supply and injection system, they would not assume well ownership. The small business would supply engineering and operations for brine supply, injection system, and collection of field producing and injection data. Phase 1--Geologic, reservoir

  9. Impact of the brine from a desalination plant on a shallow seagrass ( Posidonia oceanica) meadow

    Science.gov (United States)

    Gacia, Esperança; Invers, Olga; Manzanera, Marta; Ballesteros, Enric; Romero, Javier

    2007-05-01

    Although seawater desalination has increased significantly over recent decades, little attention has been paid to the impact of the main by-product (hypersaline water: brine) on ecosystems. In the Mediterranean, potentially the most affected ecosystems are meadows of the endemic seagrass Posidonia oceanica. We studied the effect of brine on a shallow P. oceanica meadow exposed to reverse osmosis brine discharge for more than 6 years. P. oceanica proved to be very sensitive to both eutrophication and high salinities derived from the brine discharge. Affected plants showed high epiphyte load and nitrogen content in the leaves, high frequencies of necrosis marks, low total non-structural carbohydrates and low glutamine synthetase activity, compared to control plants. However, there was no indication of extensive decline of the affected meadow. This is probably due to its very shallow situation, which results in high incident radiation as well as fast dilution and dispersion of the brine plume.

  10. Indoor tests to investigate the effect of brine depth on the performance of solar still

    Directory of Open Access Journals (Sweden)

    Marwah AW. Ali, Abdul Jabbar N. Khalifa

    2013-01-01

    Full Text Available Many experimental and numerical studies have been done on different configurations of solar stills to optimize the design by examining the effect of climatic, operational and design parameters on its performance. One of the most important of the operational parameters that has received a considerable attention in the literature is the brine depth. This paper reports indoor experimental investigations on the effect of brine depth on the productivity and efficiency of the solar stills at four different brine depths of 1.5, 2, 4 and 5.5 cm. Indoor tests were used by simulating the solar input by proper electric heaters located at the bottom of the still for heating the water contained in the basin of the still. The present study validated the decreasing trend in productivity with the increase of brine depth and showed that the still productivity could be influenced by the brine depth by up to 24%.

  11. Microbial changes and growth of Listeria monocytogenes during chilled storage of brined shrimp ( Pandalus borealis )

    DEFF Research Database (Denmark)

    Mejlholm, Ole; Kjeldgaard, J.; Modberg, A.

    2008-01-01

    and they included 53 lactic acid bacteria, 6 coagulase negative Staphylococcus spp., 18 Pseudomonas fluorescens and 5 yeast isolates. After storage at 7 degrees C, P. fluorescens, Enterococcus-like isolates, E. malodoratus, Carnobacterium maltaromaticum, coagulase negative Staphylococcus spp. and Lactobacillus...... and lactic acids were studied. Furthermore, the effect of adding diacetate to brined shrimp was evaluated. A single batch of cooked and peeled shrimp was used to study both industrially and manually processed brined shrimp with respect to the effect of process hygiene on microbial changes and the shelf life...... sakei constituted the dominating microflora of shrimp in brines that contained benzoic, citric and sorbic acids as preservatives. L sakei dominated the spoilage microflora of brined and drained MAP shrimp, and of brined shrimp preserved using acetic, citric and lactic acids, irrespective of packaging...

  12. Indoor tests to investigate the effect of brine depth on the performance of solar still

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Marwah A.W.; Jabbar N. Khalifa, Abdul [Nahrain University, College of Engineering, Jadiriya, P.O. Box 64040, Baghdad (Iraq)

    2013-07-01

    Many experimental and numerical studies have been done on different configurations of solar stills to optimize the design by examining the effect of climatic, operational and design parameters on its performance. One of the most important of the operational parameters that has received a considerable attention in the literature is the brine depth. This paper reports indoor experimental investigations on the effect of brine depth on the productivity and efficiency of the solar stills at four different brine depths of 1.5, 2, 4 and 5.5 cm. Indoor tests were used by simulating the solar input by proper electric heaters located at the bottom of the still for heating the water contained in the basin of the still. The present study validated the decreasing trend in productivity with the increase of brine depth and showed that the still productivity could be influenced by the brine depth by up to 24%.

  13. Radon depletion in xenon boil-off gas

    CERN Document Server

    Bruenner, S; Lindemann, S; Undagoitia, T Marrodán; Simgen, H

    2016-01-01

    An important background in detectors using liquid xenon for rare event searches arises from the decays of radon and its daughters. We report for the first time a reduction of $^{222}$Rn in the gas phase above a liquid xenon reservoir. We show a reduction factor of $\\gtrsim 4$ for the $^{222}$Rn concentration in boil-off xenon gas compared to the radon enriched liquid phase. A semiconductor-based $\\alpha$-detector and miniaturized proportional counters are used to detect the radon. As the radon depletion in the boil-off gas is understood as a single-stage distillation process, this result establishes the suitability of cryogenic distillation to separate radon from xenon down to the $10^{-15}\\,$mol/mol level.

  14. Radon depletion in xenon boil-off gas

    Science.gov (United States)

    Bruenner, S.; Cichon, D.; Lindemann, S.; Undagoitia, T. Marrodán; Simgen, H.

    2017-03-01

    An important background in detectors using liquid xenon for rare event searches arises from the decays of radon and its daughters. We report for the first time a reduction of ^{222}Rn in the gas phase above a liquid xenon reservoir. We show a reduction factor of ≳ 4 for the ^{222}Rn concentration in boil-off xenon gas compared to the radon enriched liquid phase. A semiconductor-based α -detector and miniaturized proportional counters are used to detect the radon. As the radon depletion in the boil-off gas is understood as a single-stage distillation process, this result establishes the suitability of cryogenic distillation to separate radon from xenon down to the 10^{-15} mol/mol level.

  15. Catastrophe characteristics of the condensation and pool boiling phenomena

    Science.gov (United States)

    Ma, Xuehu; Xu, Dunqi; Lin, Jifang

    1995-02-01

    Recently, Utaka proposed two types of the transition modes of dropwise condensation, i.e. the continuous and the jumping modes, and presented a criterion for determining the condensation transition mode. Stylianous and Rose proposed two hypotheses, the coalescence-limited transition and the nucleation site saturation transition. Neither Utaka's criterion nor Rose's hypotheses could clearly interpret the physical mechanisms of the transition both from filmwise to dropwise and from dropwise to pseudofilm condensation, and explicitly presented the main factors affecting the transitions. Kalinin hs given a general review of the transition boiling heat transfer. The catastrophe theory will be applied here to eluicidate the complex phenomena of the transitions of the condensation and boiling pattern states.

  16. Molecular Dynamics Simulation of Bubble Nucleation in Explosive Boiling

    Institute of Scientific and Technical Information of China (English)

    ZOU Yu; HUAI Xiu-Lan; LIANG Shi-Qiang

    2009-01-01

    Molecular dynamics (MD) simulation is carried out for the bubble nucleation of liquid nitrogen in explosive boiling. The heat is transferred into the simulation system by rescaling the velocity of the molecules. The results indicate that the initial equilibrium temperature of liquid and molecular cluster size affect the energy conversion in the process of bubble nucleation. The potential energy of the system violently varies at the beginning of the bubble nucleation, and then varies around a fixed value. At the end of bubble nucleation, the potential energy of the system slowly increases. In the bubble nucleation of explosive boiling, the lower the initial equilibrium temperature, the larger the size of the molecular cluster, and the more the heat transferred into the system of the simulation cell, causing the increase potential energy in a larger range.

  17. Numerical analysis on pool boiling using user defined function

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, Sung Uk; Jeon, Byong Guk; Kim, Seok; Euh, Dong-Jin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    PAFS (passive auxiliary feedwater system) adopted in the APR+ (Advanced Power Reactor Plus) of Korea is one such application. When PAFS is activated with an actuation signal, steam from the steam generator passes through heat exchanger tubes submerged in a water tank of the PAFS. Outside these heat exchanger tubes, nucleate boiling phenomena appears. In the present work, a numerical study is reported on three-dimensional transient state pool boiling of water having an immersed heat source. The velocity vector fields during the decrease in the water level are numerically investigated in a pool, and the accuracy of the results is checked by comparing the experimental results conducted using the PIV techniques by Kim et al. These numerical results can be used as basic research data for an analysis and prediction of the natural circulation phenomena in the cooling tank of the passive safety system in a nuclear power plant.

  18. Boiling heat transfer in horizontal and inclined rectangular channels

    Energy Technology Data Exchange (ETDEWEB)

    Morcos, S.M.; Mobarak, A.; Hilal, M.; Mohareb, M.R. (Cairo Univ. (Egypt))

    1987-05-01

    The present experimental investigation is concerned with boiling heat transfer of water inside both horizontal and inclined rectangular channels under a relatively low heat flux. These configurations simulate the absorber channel of line-focus solar concentrations under boiling conditions. The experimental facility includes electrically heated aluminum rectangular channels with aspect ratios of 2.67 and 0.37. The experimental results of the two-phase Nusselt number for the two aspect ratios and for the inclination angles 0, 15, 30, and 45 deg were correlated in terms of a ratio of the two-phase to the liquid-phase Reynolds number for the forced-convection vaporization region. The proposed correlations agree well with previous investigations. In the present work, classifications of the various flow patterns were made by direct observation through a glass window at the end of the test section.

  19. Measurement and modeling of CO2 solubility in NaCl brine and CO2–saturated NaCl brine density

    DEFF Research Database (Denmark)

    Yan, Wei; Huang, Shengli; Stenby, Erling Halfdan

    2011-01-01

    over climate change and energy security. This work is an experimental and modeling study of two fundamental properties in high pressure CO2–NaCl brine equilibrium, i.e., CO2 solubility in NaCl brine and CO2–saturated NaCl brine density. A literature review of the available data was presented first...... to illustrate the necessity of experimental measurements of the two properties at high pressures. An experimental method for measuring high pressure CO2 solubility in NaCl brine was then developed. With the method, CO2 solubilities in 0, 1, and 5m NaCl brines were measured at 323, 373, and 413K from 5 to 40MPa....... The corresponding density data at the same conditions were also measured. For solubility, two models used in the Eclipse simulator were tested: the correlations of Chang et al. and the Søreide and Whitson equation of state (EoS) model. The latter model was modified to improve its performance for high salinity brine...

  20. Microlayer formation characteristics in pool isolated bubble boiling of water

    Science.gov (United States)

    Yabuki, Tomohide; Nakabeppu, Osamu

    2016-10-01

    Investigation of microlayer formation characteristics is important for developing a reliable nucleate boiling heat transfer model based on accurate physical mechanisms. Although formation mechanisms of the thin liquid film in two-phase flow of confined spaces, such as micro-tubes and closely positioned parallel plates, have been thoroughly studied, microlayer formation mechanisms of pool boiling have been sparsely studied. In a previous study (Yabuki and Nakabeppu in Int J Heat Mass Transf 76:286-297, 2014; Int J Heat Mass Transf 100:851-860, 2016), the spatial distribution of initial microlayer thickness under pool boiling bubbles was calculated by transient heat conduction analysis using the local wall temperature measured with a MEMS sensor. In this study, the hydrodynamic characteristics of microlayer formation in pool boiling were investigated using the relationship between derived initial microlayer thickness and microlayer formation velocity determined by transient local heat flux data. The trend of microlayer thickness was found to change depending on the thickness of the velocity boundary layer outside the bubble foot. When the boundary layer thickness was thin, the initial microlayer thickness was determined by the boundary layer thickness, and the initial microlayer thickness proportionally increased with increasing boundary layer thickness. On the other hand, when the boundary layer was thick, the initial microlayer thickness decreased with increasing boundary layer thickness. In this thick boundary layer region, the momentum balance in the dynamic meniscus region became important, in addition to the boundary layer thickness, and the microlayer thickness, made dimensionless using boundary layer thickness, correlated with the Bond number.

  1. Prediction of film boiling heat transfer coefficients for binary mixtures

    Science.gov (United States)

    Liu, Ming-Huei; Yang, Yu-Min; Maa, Jer-Ru

    Film boiling of binary liquid mixtures may be significantly different from that of single-component liquids due to the mass diffusion effect. A theoretical analysis is performed to outline the effects of mass diffusion phenomena on film boiling heat transfer process from a horizontal cylinder heating surface to the binary liquid mixtures of ethylene oxide/water and ethanol/benzene over whole range of compositions. These two binary systems are chosen for illustrating the strong and weak mass diffusion effects, respectively, on film boiling. Furthermore, a simple correlation for predicting heat transfer coefficient is proposed to demonstrate the idea that the dimensionless F factor can satisfactorily account for the mass diffusion effect on film boiling heat transfer of binary mixtures. Zusammenfassung Infolge des Stoffdiffusionseffektes kann sich das Filmsiedeverhalten binärer Flüssigkeitsgemische ganz wesentlich von dem der Einzelkomponentenfluide unterscheiden. In einer theoretischen Studie sollen die Einflüsse der Stoffdiffusionsphänomene auf den Wärmeübergang beim Filmsieden untersucht werden, und zwar bezüglich einer horizontalen zylindrischen Heizfläche, die Wärme an die Binärgemische Ethylenoxid/Wasser und Ethanol/Benzol bei beliebigen Konzentrationsverhältnissen abgibt. Die beiden Binärsysteme wurden ausgewählt, um einmal starken und dann schwachen Einfluß des Stoffdiffusionseffektes auf das Filmsieden zu zeigen. Schließlich wird eine einfache Korrelationsbeziehung zur Berechnung von Wärmeübergangskoeffizienten vorgeschlagen, die darlegen soll, daß der dimensionslose F-Faktor geeignet ist, den Einfluß des Stoffdiffusionseffektes auf das Filmsieden binärer Gemische befriedigend zu berücksichtigen.

  2. A review on saturated boiling of liquids on tube bundles

    Science.gov (United States)

    Swain, Abhilas; Das, Mihir Kumar

    2014-05-01

    A review of recent investigation on boiling of saturated liquids over plain and enhanced tube bundles has been carried out taking the earlier review works as reference point. The experimental observations of various geometry and performance parameters studied by researchers are analyzed keeping current demand of industries in design and development of compact, efficient heat exchanging devices. The study shows that tube spacing plays an important role in determination of compactness of the heat exchanger.

  3. Survival of Escherichia coli O157:H7 during manufacture and storage of white brined cheese.

    Science.gov (United States)

    Osaili, Tareq M; Al-Nabulsi, Anas A; Olaimat, Amin N; Shaker, Reyad R; Taha, Mohammad; Holley, Richard A

    2014-09-01

    Escherichia coli O157:H7 is a major foodborne pathogen that causes severe disease in humans. Survival of E. coli O157:H7 during processing and storage of white brined cheese was investigated. Cheeses were prepared using pasteurized milk inoculated with a 4 strain E. coli O157:H7 cocktail (7 log(10) CFU/g) with or without yogurt starter culture (Lactobacillus delbrueckii ssp. bulgaricus and Streptococcus salivarius ssp. thermophilus) and stored in 10% or 15% NaCl brine at 10 and 21 ºC for 28 d. NaCl concentration, water activity (a(w)), pH, and numbers of E. coli O157:H7 and lactic acid bacteria (LAB) were determined in cheese and brine. E. coli O157:H7 was able to survive in cheese stored in both brines at 10 and 21 ºC regardless of the presence of starter LAB, although the latter significantly enhanced E. coli O157:H7 reduction in cheese or its brine at 10 ºC. E. coli O157:H7 numbers were reduced by 2.6 and 3.4 log(10) CFU/g in cheese stored in 10% and 15% NaCl brine, respectively, in the presence of starter LAB and by 1.4 and 2.3 log(10) CFU/g, respectively, in the absence of starter LAB at 10 ºC. The pathogen survived, but at lower numbers in the brines. The salt concentration of cheese stored in 10% brine remained about 5% during ripening, but in 15% brine, the NaCl level increased 1.6% to 8.1% (w/w) by 28 d. Values of pH and a(w) slightly decreased 1 d after exposure to brine and reached 5.5 to 6.6 and 0.88 to 0.94, respectively, in all treatments.

  4. Pool boiling on rectangular fins with tunnel-pore structure

    Directory of Open Access Journals (Sweden)

    Pastuszko A.

    2013-04-01

    Full Text Available Complex experimental investigations were conducted in the area of pool boiling heat transfer on extended surfaces with internal tunnels limited by perforated foil. The experiments were carried out for water and R-123 at atmospheric pressure. The tunnel surfaces were fabricated from 0.05 – 0.1 mm thick perforated copper foil (pore diameters: 0.3, 0.4, 0.5 mm sintered with mini-fins formed by 5 and 10 mm high rectangular fins and horizontal inter-fin surface. The effect of the main fin height, pore diameters and tunnel pitch on nucleate pool boiling was examined. Substantial enhancement of heat transfer coefficient was observed for the investigated surfaces. The highest increase in the heat transfer coefficient was obtained for the 10 mm high fins – about 50kW/m2K for water and 15 kW/m2K for R-123. The investigated surfaces showed boiling heat transfer coefficients similar to those of existing tunnel-pore structures.

  5. Boiling of an emulsion in a yield stress fluid

    Science.gov (United States)

    Guéna, Geoffroy; Wang, Ji; D'Espinose, Jean-Baptiste; Lequeux, François; Talini, Laurence

    2010-11-01

    We report the boiling behavior of pentane emulsified in a yield stress fluid, a colloidal clay (Laponite) suspension. We have observed that a superheated state is easily reached: the emulsion, heated more than 50°C above the alkane boiling point, does not boil. Superheating is made possible by the suppression of heterogeneous nucleation in pentane, resulting from the emulsification process, a phenomenon evidenced decades ago in studies of the superheating of two phase fluids. We have furthermore studied the growth of isolated bubbles nucleated in the emulsion. The rate of increase of the bubble radius with time depends on both the temperature and emulsion volume fraction but, rather unexpectedly, does not depend on the fluid rheology. We show that the bubbles grow by diffusion of the alkane through the aqueous phase between liquid droplets and bubbles, analogously to an Ostwald ripening process. The peculiarity of the process reported here is that a layer depleted in oil droplets forms around the bubble, layer to which the alkane concentration gradient is confined. We successfully describe our experimental results with a simple transfer model.

  6. Early-Evaporation of Microlayer for Boiling Heat Transfer Enhancement.

    Science.gov (United States)

    Zou, An; Singh, Dhirendra P; Maroo, Shalabh C

    2016-10-06

    For over five decades, enhancement in pool boiling heat transfer has been achieved by altering the surface wetting, wickability, roughness, nucleation site density and providing separate liquid/vapor pathways. In this work, a new enhancement mechanism based on the early-evaporation of the microlayer is discovered and validated. The microlayer is a thin liquid film present at the base of a vapor bubble. Presence of micro-ridges on the silicon-dioxide surface partitions the microlayer and disconnects it from bulk liquid causing it to evaporate sooner, thus leading to increase in bubble growth rate, heat transfer, departure frequency and critical heat flux (CHF). Compared to a plain surface, ~120% enhancement in CHF is obtained with only ~18% increase in surface area. A CHF enhancement map is developed based on ridge height and spacing, resulting in three regions of full, partial and no enhancement. The new mechanism is validated by comparing the growth rate of a laser created vapor bubble on ridge-structured surface and plain surface, and the corresponding prediction of CHF enhancement is found to be in good agreement with experimental boiling data. This discovery opens up a new field of CHF enhancement and can be coupled with existing techniques to further push the limits of boiling heat transfer.

  7. Experimental Investigation of Flow Boiling in Parallel Mini-channels

    Science.gov (United States)

    Wu, Wan.; Zhang, M. T.; Zhang, X. B.; Xia, J. J.; Wen, S.-Z.; Wang, Z.-R.; He, Z.-H.; Huang, Z.-C.

    2015-07-01

    Flow boiling in micro-channels and mini-channels has received significant attention due to its capability for dissipating highflux heat, especially in the thermal management of high precision electronics. A heat sink with narrow rectangular mini-channels is designed to investigate flow boiling in the mini-channels, including the effect of gravity. It contains 14 parallel channels with a cross section, of 1×4mm 2, of which the hydraulic diameter is 1.6mm. The cooling capability, the temperature uniformity, and the temperature stability of the flow boiling in minichannels are investigated with R22, with total mass flow flux ranges from 35 to 70kg/m 2s. The results show that the cooling capability of the heat- sink is up to 340W(˜ 3.0W/cm 2), and the temperature difference is below 4 ∘C(even down to 2 ∘C) on the heat sink. The temperature uniformity isn't quite sensitive to heat flux. The instability has not been observed in the present researches.

  8. Water quality in the vicinity of Mosquito Creek Lake, Trumbull County, Ohio, in relation to the chemistry of locally occurring oil, natural gas, and brine

    Science.gov (United States)

    Barton, G.J.; Burruss, R.C.; Ryder, R.T.

    1998-01-01

    Sandstone water samples indicates that the gas is microbially generated, whereas the Clinton sandstone gases are thermogenically generated. Methane gas, in addition to crude oil, occurs naturally in the shallow Berea and Cussewago Sandstone aquifers in the Mosquito Creek Lake area and concentrations of dissolved methane are significant in the city of Cortland public-supply wells and in the domestic-supply wells near the southern shore of the lake. Water associated with oil and gas in the Clinton sandstone is a brine with high concentrations of chloride. Water from the Berea and Cussewago Sandstones, however, is fresh and potable. The contrasting geochemical characteristics are important for addressing water-quality issues that relate to oil and natural gas development in the Mosquito Creek area. A reexamination of the geologic framework and results of a subsurface-gas survey show that crude oil in the historic Mecca Oil Pool probably does not seep into Mosquito Creek Lake. Environmental samples show no evidence of any measurable release of oil, gas, or brine from the deeper Clinton sandstone oil and gas wells to the shallow aquifers, the lake, or lake tributaries. Brine is not associated with the hydrocarbons in the shallow Berea-Cussewago aquifer system and therefore cannot be a source of brine contamination. A mixing diagram constructed for dissolved bromide and chloride in surface water and water-supply wells shows no demonstrable mixing of these water resources with brine from the Clinton sandstone. There is some notable salinity in surface waters; however, the water is bromide poor, and a mixing diagram indicates that some local ground waters are influenced by halite solutions, presumably derived from leaching of road salt or from septic effluent.

  9. Studies Update Vinyl Chloride Hazards.

    Science.gov (United States)

    Rawls, Rebecca

    1980-01-01

    Extensive study affirms that vinyl chloride is a potent animal carcinogen. Epidemiological studies show elevated rates of human cancers in association with extended contact with the compound. (Author/RE)

  10. Parameters Affecting Hydrogen Chloride Measurements

    Science.gov (United States)

    1993-06-01

    contain sea salt, which is hygroscopic because of the magnesium chloride present, or ammonium bisulfate , which mostly comes from sulfur pollution and is...boosters release hydrogen chloride as a combustion product, and hydrazines or nitric acid can be spilled from liquid fuel motors. Monitoring the...solubility constant, and the second is the acid ionization constant. From experimental work, the product of the two constants is well established (Reference

  11. Chloride channels in stroke

    Institute of Scientific and Technical Information of China (English)

    Ya-ping ZHANG; Hao ZHANG; Dayue Darrel DUAN

    2013-01-01

    Vascular remodeling of cerebral arterioles,including proliferation,migration,and apoptosis of vascular smooth muscle cells (VSMCs),is the major cause of changes in the cross-sectional area and diameter of the arteries and sudden interruption of blood flow or hemorrhage in the brain,ie,stroke.Accumulating evidence strongly supports an important role for chloride (Clˉ) channels in vascular remodeling and stroke.At least three Clˉ channel genes are expressed in VSMCs:1) the TMEM16A (or Ano1),which may encode the calcium-activated Clˉ channels (CACCs); 2) the CLC-3 Clˉ channel and Clˉ/H+ antiporter,which is closely related to the volume-regulated Clˉ channels (VRCCs); and 3) the cystic fibrosis transmembrane conductance regulator (CFTR),which encodes the PKA-and PKC-activated Clˉ channels.Activation of the CACCs by agonist-induced increase in intracellular Ca2+ causes membrane depolarization,vasoconstriction,and inhibition of VSMC proliferation.Activation of VRCCs by cell volume increase or membrane stretch promotes the production of reactive oxygen species,induces proliferation and inhibits apoptosis of VSMCs.Activation of CFTR inhibits oxidative stress and may prevent the development of hypertension.In addition,Clˉ current mediated by gammaaminobutyric acid (GABA) receptor has also been implicated a role in ischemic neuron death.This review focuses on the functional roles of Clˉ channels in the development of stroke and provides a perspective on the future directions for research and the potential to develop Clˉ channels as new targets for the prevention and treatment of stroke.

  12. 21 CFR 184.1138 - Ammonium chloride.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium chloride. 184.1138 Section 184.1138 Food... Specific Substances Affirmed as GRAS § 184.1138 Ammonium chloride. (a) Ammonium chloride (NH4Cl, CAS Reg. No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution....

  13. Hydrographic changes during 20 years in the brine-filled basins of the Red Sea

    Science.gov (United States)

    Anschutz, Pierre; Blanc, Gérard; Chatin, Fabienne; Geiller, Magali; Pierret, Marie-Claire

    1999-10-01

    Many of the deep basins filled by hot brines in the Red Sea have not been investigated since their discovery in the early 1970s. Twenty years later, in September 1992, six of these deeps were revisited. The temperature and salinity of the Suakin, Port Sudan, Chain B, and Nereus deeps ranged from 23.25 to 44.60°C and from 144 to 270‰. These values were approximately the same in 1972, indicating that the budget of heat and salt was quite balanced. We measured strong gradients of properties in the transition zone between brines and overlying seawater. The contribution of salinity to the density gradient was more than one order of magnitude higher than the opposite contribution of temperature across the seawater-brine interface. Therefore the interface was extemely stable, and the transfer of properties across it was considered to be controlled mostly by molecular diffusion. We calculate that the diffusional transport of salt from the brines to seawater cannot affect significantly the salinity of the brines over a 20 year period, which agrees with the observations. The brine pools can persist for centuries with no salt input. Therefore, the persisence of brines does not correspond to a steady balance between diffusional loss and continuous input of hydrothermal solutions. Deeps that experience only episodical hydrothermal brine supplies may persist for a long time with salt inherited from past inputs. The theoretical loss of heat by diffusion from the brine to seawater was higher than the observed decrease in temperature of the brine pool during the 20 year period of observation. We calculated that the heat flux out of the pools into the overlying seawater was compensated by a heat flux into the pools of about 250-600 mW/m 2. This range of values corresponds to bottom heat flow values that have been reported earlier for the axial zone of the Red Sea. In contrast to the other brine pools, the temperature and salinity of the Valdivia Deep brine increased by 4.1°C and

  14. CHF Phenomena by Photographic Study of Boiling Behavior due to Transient Heat Inputs

    Directory of Open Access Journals (Sweden)

    Jongdoc Park

    2012-01-01

    Full Text Available The transient boiling heat transfer characteristics in a pool of water and highly wetting liquids such as ethanol and FC-72 due to an exponentially increasing heat input of various rates were investigated using the 1.0 mm diameter experimental heater shaped in a horizontal cylinder for wide ranges of pressure and subcooling. The trend of critical heat flux (CHF values in relation to the periods was divided into three groups. The CHF belonging to the 1st group with a longer period occurs with a fully developed nucleate boiling (FDNB heat transfer process. For the 2nd group with shorter periods, the direct transition to film boiling from non boiling occurs as an explosive boiling. The direct boiling transition at the CHF from non-boiling regime to film boiling occurred without a heat flux increase. It was confirmed that the initial boiling behavior is significantly affected by the property and the wettability of the liquid. The photographic observations on the vapor bubble behavior during transitions to film boiling were performed using a high-speed video camera system.

  15. Rheological Properties and Structural Changes in Different Sections of Boiled Abalone Meat

    Institute of Scientific and Technical Information of China (English)

    GAO Xin; TANG Zhixu; ZHANG Zhaohui; Ogawa Hiroo

    2003-01-01

    Changes in tissue structures, rheological properties of cross- and vertical section boiled abalone meat were studied in relation to boiling time. The adductor muscle of abalone Haliotis discus which was removed from the shell, was boiled for 1, 2, and 3 h, respectively. Then it was cut up and separated into cross- and vertical section meat. When observed by a light microscope and a scanning electron microscope, structural changes in the myofibrils were greatest in the cross section meat compared with the vertical section meat. When boiling time was increased from 1 h to 3 h, the instantaneous modulus E0 and rupture strength of both section meat decreased gradually with increased boiling time, and no significant differences were observed between these two section meat for the same boiling time. When boiled for 1 h, the relaxation time of cross section meat was much longer than that of vertical section meat. There were no significant changes in the relaxation time of vertical section for different boiling time, but the relaxation time of cross section meat was reduced gradually with increasing boiling time. These results confirmed that the difference in rheological properties between the cross- and vertical section meat was mainly due to the denaturation level of myofibrils when heated for 1 h, as well as due to the changes in the amount of denatured proteins, and the manner in which the inner denatured protein components weve exchanged after boiling time was increased from 1 h to 3 h.

  16. Study on model of onset of nucleate boiling in natural circulation with subcooled boiling using unascertained mathematics

    Energy Technology Data Exchange (ETDEWEB)

    Zhou Tao [Department of Thermal Engineering, Tsinghua University, Beijing 100084 (China)]. E-mail: zhoutao@mail.tsinghua.edu.cn; Wang Zenghui [Department of Engineering Mechanics, Tsinghua University, Beijing 100084 (China); Yang Ruichang [Department of Thermal Engineering, Tsinghua University, Beijing 100084 (China)

    2005-10-01

    Experiment data got from onset of nucleate boiling (ONB) in natural circulation is analyzed using unascertained mathematics. Unitary mathematics model of the relation between the temperature and onset of nucleate boiling is built up to analysis ONB. Multiple unascertained mathematics models are also built up with the onset of natural circulation boiling equation based on the experiment. Unascertained mathematics makes that affirmative results are a range of numbers that reflect the fluctuation of experiment data more truly. The fluctuating value with the distribution function F(x) is the feature of unascertained mathematics model and can express fluctuating experimental data. Real status can be actually described through using unascertained mathematics. Thus, for calculation of ONB point, the description of unascertained mathematics model is more precise than common mathematics model. Based on the unascertained mathematics, a new ONB model is developed, which is important for advanced reactor safety analysis. It is conceivable that the unascertained mathematics could be applied to many other two-phase measurements as well.

  17. Long-Term Corrosion Potential Behavior of Alloy 22 in Hot 5 m CaCl2 + 5 m Ca(NO3)2 Brines

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, M A; Carranza, R M; Stuart, M L; Rebak, R B

    2007-02-20

    Alloy 22 is a nickel base alloy highly resistant to all forms of corrosion. In very aggressive conditions (e.g. hot concentrated chloride containing brines) Alloy 22 could suffer localized attack, namely pitting and crevice corrosion. The occurrence of localized corrosion in a given environment is governed by the values of the critical potential (E{sub crit}) for crevice corrosion and the corrosion potential (E{sub corr}) that the alloy may establish in the studied environment. If E{sub corr} is equal or higher than E{sub crit}, localized corrosion may be expected. This paper discusses the evolution of E{sub corr} of Alloy 22 specimens in 5 m CaCl{sub 2} + 5 m Ca(NO{sub 3}){sub 2} brines at 100 C and 120 C. Two types of specimens were used, polished as-welded (ASW) creviced and noncreviced specimens and as-welded plus solution heat-treated (ASW+SHT) creviced specimens. The latter contained the black annealing oxide film on the surface. Results show that, for all types of Alloy 22 specimens the E{sub corr} was higher at 120 C than at 100 C, probably because a more protective film formed at the higher temperature. Specimens with the black oxide film on the surface showed more oscillations in the potential. None of the tested specimens suffered crevice corrosion probably because of the relatively high concentration of nitrate in the electrolyte, R = [NO3]/[Cl] = 1.

  18. 46 CFR 151.50-34 - Vinyl chloride (vinyl chloride monomer).

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Vinyl chloride (vinyl chloride monomer). 151.50-34... chloride (vinyl chloride monomer). (a) Copper, aluminum, magnesium, mercury, silver, and their alloys shall... equipment that may come in contact with vinyl chloride liquid or vapor. (b) Valves, flanges, and...

  19. 40 CFR 61.65 - Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... dichloride, vinyl chloride and polyvinyl chloride plants. 61.65 Section 61.65 Protection of Environment... AIR POLLUTANTS National Emission Standard for Vinyl Chloride § 61.65 Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants. An owner or operator of an ethylene...

  20. Quorum Quenching Bacillus sonorensis Isolated from Soya Sauce Fermentation Brine

    Directory of Open Access Journals (Sweden)

    Kok-Gan Chan

    2012-03-01

    Full Text Available An N-acylhomoserine lactone (AHL-degrading bacterial strain, L62, was isolated from a sample of fermentation brine of Chinese soya sauce by using rich medium agar supplemented with soya sauce (10% v/v. L62, a rod-shaped Gram positive bacterium with amylolytic activity, was phylogentically related to Bacillus sonorensis by 16S ribosomal DNA and rpoB sequence analyses. B. sonorensis L62 efficiently degraded N-3-oxohexanoyl homoserine lactone and N-octanoylhomoserine lactone. However, the aiiA homologue, encoding an autoinducer inactivation enzyme catalyzing the degradation of AHLs, was not detected in L62, suggesting the presence of a different AHL-degrading gene in L62. To the best of our knowledge, this is the first report of AHL-degrading B. sonorensis from soya sauce liquid state fermentation.

  1. Guiding brine shrimp through mazes by solving reaction diffusion equations

    Science.gov (United States)

    Singal, Krishma; Fenton, Flavio

    Excitable systems driven by reaction diffusion equations have been shown to not only find solutions to mazes but to also to find the shortest path between the beginning and the end of the maze. In this talk we describe how we can use the Fitzhugh-Nagumo model, a generic model for excitable media, to solve a maze by varying the basin of attraction of its two fixed points. We demonstrate how two dimensional mazes are solved numerically using a Java Applet and then accelerated to run in real time by using graphic processors (GPUs). An application of this work is shown by guiding phototactic brine shrimp through a maze solved by the algorithm. Once the path is obtained, an Arduino directs the shrimp through the maze using lights from LEDs placed at the floor of the Maze. This method running in real time could be eventually used for guiding robots and cars through traffic.

  2. Effect of electroosmotic flow on brine imbibition in porous media

    Institute of Scientific and Technical Information of China (English)

    Rui WANG; Xiang-an YUE; Xu WEI; Wei ZHANG

    2009-01-01

    Based on Darcy's Law and the Helmholta-Smoluchowski equation, an imbibition velocity formula for the water phase with an electric field was deduced, showing that the imbibition velocity with an electric field is to various extents not only-related to the rock permeability and characteristic length, the fluid viscosity, the oil-water interface tension and the gravity of the imbibing brine, but also to the fluid dielectric permittivity, zeta potential, applied electric field direction, and strength. Imbibition experiments with electric fields that are different in direction and strength were conducted, showing that application of a positive electric field enhances the imbibition velocity and increases the imbibition recovery ratio, while application of a negative electric field reduces the imbibition velocity and decreases the imbibition recovery ratio. The imbibition recovery ratio with a positive electric field increases with the strength of the electric field, and the imbibition recovery ratio with a negative electric field is lower than that without an electric field.

  3. Microprobe analysis of brine shrimp grown on meteorite extracts

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, J. [National Isotope Centre, GNS Science, 30 Gracefield Road, Lower Hutt (New Zealand)]. E-mail: j.kennedy@gns.cri.nz; Mautner, M.N. [Soil, Plant and Ecological Sciences Division, Lincoln University (New Zealand) and Department of Chemistry, University of Canterbury, Christchurch 8001 (New Zealand)]. E-mail: m.mautner@solis1.com; Barry, B. [National Isotope Centre, GNS Science, 30 Gracefield Road, Lower Hutt (New Zealand); Markwitz, A. [National Isotope Centre, GNS Science, 30 Gracefield Road, Lower Hutt (New Zealand)

    2007-07-15

    Nuclear microprobe methods have been used to investigate the uptake and distribution of various elements by brine shrimps and their unhatched eggs when grown in extracts of the Murchison and Allende carbonaceous meteorites, which were selected as model space resources. Measurements were carried out using a focussed 2 MeV proton beam raster scanned over the samples in order to obtain the average elemental concentrations. Line scans across the egg and shrimp samples show uptake of elements such as Mg, Ni, S and P which are present in the meteorites. The results confirmed that carbonaceous chondrite materials can provide nutrients, including high levels of the essential nutrient phosphate. The concentrations of these elements varied significantly between shrimp and eggs grown in extracts of the two meteorite types, which can help in identifying optimal growth media. Our results illustrate that nuclear microprobe techniques can determine elemental concentrations in organisms exposed to meteorite derived media and thus help in identifying useful future resources.

  4. In-situ fracture mapping using geotomography and brine tracers

    Energy Technology Data Exchange (ETDEWEB)

    Deadrick, F.J.; Ramirez, A.L.; Lytle, R.J.

    1981-01-01

    The Lawrence Livermore National Laboratory is currently assessing the capabilities of high resolution geophysical methods to characterize geologic sites for the disposal of high level nuclear waste. A successful experiment has recently been performed in which salt water tracers and high frequency electromagnetic waves were utilized to map rock mass fracture zones in-situ. Multiple cross-borehole EM transmissions were used to generate a tomographic image of the fractured rock region between two boreholes. The tomographs obtained correlate well with conventional wireline geophysical logs which can be used to infer the location of fractured zones in the rock mass. This indirect data suggests that the geotomography and brine tracer technique may have merit in mapping fractured zones between boreholes.

  5. Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination

    Science.gov (United States)

    Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J.; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

    2016-08-01

    There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes.

  6. Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination.

    Science.gov (United States)

    Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

    2016-08-22

    There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes.

  7. Alcohol Brine Freezing of Japanese Horse Mackerel (Trachurus japonicus) for Raw Consumption

    Science.gov (United States)

    Maeda, Toshimichi; Yuki, Atsuhiko; Sakurai, Hiroshi; Watanabe, Koichiro; Itoh, Nobuo; Inui, Etsuro; Seike, Kazunori; Mizukami, Yoichi; Fukuda, Yutaka; Harada, Kazuki

    In order to test the possible application of alcohol brine freezing to Japanese horse mackerel (Trachurus japonicus) for raw consumption, the quality and taste of fish frozen by direct immersion in 60% ethanol brine at -20, -25 and -30°C was compared with those by air freezing and fresh fish without freezing. Cracks were not found during the freezing. Smell of ethanol did not remain. K value, an indicator of freshness, of fish frozen in alcohol brine was less than 8.3%, which was at the same level as those by air freezing and fresh fish. Oxidation of lipid was at the same level as air freezing does, and lower than that of fresh fish. The pH of fish frozen in alcohol brine at -25 and -30°C was 6.5 and 6.6, respectively, which were higher than that by air freezing and that of fresh fish. Fish frozen in alcohol brine was better than that by air and at the same level as fresh fish in total evaluation of sensory tests. These results show that the alcohol brine freezing is superior to air freezing, and fish frozen in alcohol brine can be a material for raw consumption. The methods of thawing in tap water, cold water, refrigerator, and at room temperature were compared. Thawing in tap water is considered to be convenient due to the short thaw time and the quality of thawed fish that was best among the methods.

  8. Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination

    Science.gov (United States)

    Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J.; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

    2016-01-01

    There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes. PMID:27545955

  9. Viruses-to-mobile genetic elements skew in the deep Atlantis II brine pool sediments.

    Science.gov (United States)

    Adel, Mustafa; Elbehery, Ali H A; Aziz, Sherry K; Aziz, Ramy K; Grossart, Hans-Peter; Siam, Rania

    2016-09-06

    The central rift of the Red Sea has 25 brine pools with different physical and geochemical characteristics. Atlantis II (ATIID), Discovery Deeps (DD) and Chain Deep (CD) are characterized by high salinity, temperature and metal content. Several studies reported microbial communities in these brine pools, but few studies addressed the brine pool sediments. Therefore, sediment cores were collected from ATIID, DD, CD brine pools and an adjacent brine-influenced site. Sixteen different lithologic sediment sections were subjected to shotgun DNA pyrosequencing to generate 1.47 billion base pairs (1.47 × 10(9) bp). We generated sediment-specific reads and attempted to annotate all reads. We report the phylogenetic and biochemical uniqueness of the deepest ATIID sulfur-rich brine pool sediments. In contrary to all other sediment sections, bacteria dominate the deepest ATIID sulfur-rich brine pool sediments. This decrease in virus-to-bacteria ratio in selected sections and depth coincided with an overrepresentation of mobile genetic elements. Skewing in the composition of viruses-to-mobile genetic elements may uniquely contribute to the distinct microbial consortium in sediments in proximity to hydrothermally active vents of the Red Sea and possibly in their surroundings, through differential horizontal gene transfer.

  10. Selenium biotransformations in an engineered aquatic ecosystem for bioremediation of agricultural wastewater via brine shrimp production.

    Science.gov (United States)

    Schmidt, Radomir; Tantoyotai, Prapakorn; Fakra, Sirine C; Marcus, Matthew A; Yang, Soo In; Pickering, Ingrid J; Bañuelos, Gary S; Hristova, Krassimira R; Freeman, John L

    2013-05-21

    An engineered aquatic ecosystem was specifically designed to bioremediate selenium (Se), occurring as oxidized inorganic selenate from hypersalinized agricultural drainage water while producing brine shrimp enriched in organic Se and omega-3 and omega-6 fatty acids for use in value added nutraceutical food supplements. Selenate was successfully bioremediated by microalgal metabolism into organic Se (seleno-amino acids) and partially removed via gaseous volatile Se formation. Furthermore, filter-feeding brine shrimp that accumulated this organic Se were removed by net harvest. Thriving in this engineered pond system, brine shrimp ( Artemia franciscana Kellogg) and brine fly (Ephydridae sp.) have major ecological relevance as important food sources for large populations of waterfowl, breeding, and migratory shore birds. This aquatic ecosystem was an ideal model for study because it mimics trophic interactions in a Se polluted wetland. Inorganic selenate in drainage water was metabolized differently in microalgae, bacteria, and diatoms where it was accumulated and reduced into various inorganic forms (selenite, selenide, or elemental Se) or partially incorporated into organic Se mainly as selenomethionine. Brine shrimp and brine fly larva then bioaccumulated Se from ingesting aquatic microorganisms and further metabolized Se predominately into organic Se forms. Importantly, adult brine flies, which hatched from aquatic larva, bioaccumulated the highest Se concentrations of all organisms tested.

  11. Wettability from Capillarity of CO2-Brine-Rock Systems at Reservoir Conditions

    Science.gov (United States)

    Al-Menhali, Ali; Niu, Ben; Krevor, Samuel

    2015-04-01

    The wettability of CO2-brine-rock systems will have a major impact on the management of carbon sequestration in subsurface geological formations. Recent contact angle measurement studies have reported sensitivity in wetting behaviour of this system to pressure, temperature and brine salinity. We report results of an investigation into the impact of reservoir conditions on wetting through direct observations of their impact on the capillary strength of the system. Eight capillary pressure characteristic curves were measured using CO2 and brine in a single fired Berea sandstone at pressures (5 to 20 MPa), temperatures (25 to 50 °C) and ionic strengths (0 to 5 M kg-1 NaCl) representative of subsurface reservoirs. A ninth measurement using an N2-water system provided a benchmark for capillarity with a strongly water wet system. The semi-dynamic capillary pressure core flooding technique was used with in situ saturation monitoring. In all cases, the capillarity of the system, scaled by the interfacial tension, were equivalent to the N2-water system within measurement uncertainty. Thus reservoir conditions did not have a significant impact on the capillary strength of the CO2-brine system through a variation in wetting. Two steady-state relative permeability measurements with CO2 and brine and one with N2 and brine similarly show little variation between conditions, consistent with the observation that the CO2-brine-sandstone system is strongly water wetting and invariant across a wide range of reservoir conditions.

  12. Capillarity and wetting of carbon dioxide and brine during drainage in Berea sandstone at reservoir conditions

    Science.gov (United States)

    Al-Menhali, Ali; Niu, Ben; Krevor, Samuel

    2015-10-01

    The wettability of CO2-brine-rock systems will have a major impact on the management of carbon sequestration in subsurface geological formations. Recent contact angle measurement studies have reported sensitivity in wetting behavior of this system to pressure, temperature, and brine salinity. We report observations of the impact of reservoir conditions on the capillary pressure characteristic curve and relative permeability of a single Berea sandstone during drainage—CO2 displacing brine—through effects on the wetting state. Eight reservoir condition drainage capillary pressure characteristic curves were measured using CO2 and brine in a single fired Berea sandstone at pressures (5-20 MPa), temperatures (25-50°C), and ionic strengths (0-5 mol kg-1 NaCl). A ninth measurement using a N2-water system provided a benchmark for capillarity with a strongly water wet system. The capillary pressure curves from each of the tests were found to be similar to the N2-water curve when scaled by the interfacial tension. Reservoir conditions were not found to have a significant impact on the capillary strength of the CO2-brine system during drainage through a variation in the wetting state. Two steady-state relative permeability measurements with CO2 and brine and one with N2 and brine similarly show little variation between conditions, consistent with the observation that the CO2-brine-sandstone system is water wetting and multiphase flow properties invariant across a wide range of reservoir conditions.

  13. Viruses-to-mobile genetic elements skew in the deep Atlantis II brine pool sediments

    Science.gov (United States)

    Adel, Mustafa; Elbehery, Ali H. A.; Aziz, Sherry K.; Aziz, Ramy K.; Grossart, Hans-Peter; Siam, Rania

    2016-09-01

    The central rift of the Red Sea has 25 brine pools with different physical and geochemical characteristics. Atlantis II (ATIID), Discovery Deeps (DD) and Chain Deep (CD) are characterized by high salinity, temperature and metal content. Several studies reported microbial communities in these brine pools, but few studies addressed the brine pool sediments. Therefore, sediment cores were collected from ATIID, DD, CD brine pools and an adjacent brine-influenced site. Sixteen different lithologic sediment sections were subjected to shotgun DNA pyrosequencing to generate 1.47 billion base pairs (1.47 × 109 bp). We generated sediment-specific reads and attempted to annotate all reads. We report the phylogenetic and biochemical uniqueness of the deepest ATIID sulfur-rich brine pool sediments. In contrary to all other sediment sections, bacteria dominate the deepest ATIID sulfur-rich brine pool sediments. This decrease in virus-to-bacteria ratio in selected sections and depth coincided with an overrepresentation of mobile genetic elements. Skewing in the composition of viruses-to-mobile genetic elements may uniquely contribute to the distinct microbial consortium in sediments in proximity to hydrothermally active vents of the Red Sea and possibly in their surroundings, through differential horizontal gene transfer.

  14. Weeks Island brine diffuser site study: baseline conditions and environmental assessment technical report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-12-12

    This technical report presents the results of a study conducted at two alternative brine diffuser sites (A and B) proposed for the Weeks Island salt dome, together with an analysis of the potential physical, chemical, and biological effects of brine disposal for this area of the Gulf of Mexico. Brine would result from either the leaching of salt domes to form or enlarge oil storage caverns, or the subsequent use of these caverns for crude oil storage in the Strategic Petroleum Reserve (SPR) program. Brine leached from the Weeks Island salt dome would be transported through a pipeline which would extend from the salt dome either 27 nautical miles (32 statute miles) for Site A, or 41 nautical miles (47 statute miles) for Site B, into Gulf waters. The brine would be discharged at these sites through an offshore diffuser at a sustained peak rate of 39 ft/sup 3//sec. The disposal of large quantities of brine in the Gulf could have a significant impact on the biology and water quality of the area. Physical and chemical measurements of the marine environment at Sites A and B were taken between September 1977 and July 1978 to correlate the existing environmental conditions with the estimated physical extent of tthe brine discharge as predicted by the MIT model (US Dept. of Commerce, 1977a). Measurements of wind, tide, waves, currents, and stratification (water column structure) were also obtained since the diffusion and dispersion of the brine plume are a function of the local circulation regime. These data were used to calculate both near- and far-field concentrations of brine, and may also be used in the design criteria for diffuser port configuration and verification of the plume model. Biological samples were taken to characterize the sites and to predict potential areas of impact with regard to the discharge. This sampling focused on benthic organisms and demersal fish. (DMC)

  15. Carbon isotopic evidence for microbial control of carbon supply to Orca Basin at the brine-seawater interface

    Directory of Open Access Journals (Sweden)

    S. R. Shah

    2012-12-01

    Full Text Available Orca Basin, an intraslope basin on the Texas–Louisiana continental slope, hosts a hypersaline, anoxic brine in its lowermost 200 m. This brine contains a large reservoir of reduced and aged carbon, and appears to be stable at decadal time scales: concentrations and the isotopic composition of dissolved inorganic (DIC and organic carbon (DOC are similar to previous reports. Both DIC and DOC are more "aged" within the brine pool than in overlying water, and the isotopic contrast between brine carbon and seawater carbon is much greater for DIC than DOC. While the stable carbon isotopic composition of brine DIC points towards a combination of methane and organic carbon re-mineralization as its source, radiocarbon and box model results point to the brine interface as the major source region for DIC with oxidation of methane diffusing upwards from sediments supplying only limited DIC to the brine. This conclusion is consistent with previous studies reporting microbial activity focused at the seawater-brine interface. Isotopic similarities between DIC and DOC suggest a different relationship between these two carbon reservoirs than is typically observed in deep ocean basins. Radiocarbon values implicate the seawater-brine interface region as the likely source region for DOC as well as DIC. Further investigations of the seawater-brine interface are needed to advance our understanding of the specific microbial processes contributing to dissolved carbon storage in the Orca Basin brine.

  16. Boil-off gas vapors are recovered by reliquefaction in LNG

    Energy Technology Data Exchange (ETDEWEB)

    Levay, M.; Petit, P.; Paradowski, H.

    1986-02-24

    Although great care is taken to prevent heat leaks into cryogenic equipment in LNG terminals, boil-off vapors evolve from LNG stored at thermodynamic equilibrium. The quantities of boil-off vapors may be quite considerable. They account for about 1% of the total gas quantity received and sent out at the monitor-de-bretagne LNG terminal of Gaz de France. A novel process has significantly cut boil-off vapor handling costs. It is free of technical problems which would arise from local utilization of the gas and makes boil-off recovery possible under optimum conditions. In addition, the process shows an excellent degree of reliability. Boil-off vapors have a lower heating value than the stored LNG. However, since they mainly consist of methane, their economic usefulness makes vapor recovery necessary. This boil-off gas, with widely fluctuating quantities and qualities, cannot be readily used locally. The vapors must be sent out into the grid.

  17. A sulfate conundrum: Dissolved sulfates of deep-saline brines and carbonate-associated sulfates

    Science.gov (United States)

    Labotka, Dana M.; Panno, Samuel V.; Locke, Randall A.

    2016-10-01

    Sulfates in deeply circulating brines and carbonate-associated sulfates (CAS) within sedimentary units of the Cambrian strata in the Illinois Basin record a complex history. Dissolved sulfate within the Mt. Simon Sandstone brines exhibits average δ34SSO4 values of 35.4‰ and δ18OSO4 values of 14.6‰ and appears to be related to Cambrian seawater sulfate, either original seawater or sourced from evaporite deposits such as those in the Michigan Basin. Theoretical and empirical relationships based on stable oxygen isotope fractionation suggest that sulfate within the lower depths of the Mt. Simon brines has experienced a long period of isolation, possibly several tens of millions of years. Comparison with brines from other stratigraphic units shows the Mt. Simon brines are geochemically unique. Dissolved sulfate from brines within the Ironton-Galesville Sandstone averages 22.7‰ for δ34SSO4 values and 13.0‰ for δ18OSO4 values. The Ironton-Galesville brine has mixed with younger groundwater, possibly of Ordovician to Devonian age and younger. The Eau Claire Formation lies between the Mt. Simon and Ironton-Galesville Sandstones. The carbonate units of the Eau Claire and stratigraphically equivalent Bonneterre Formation contain CAS that appears isotopically related to the Late Pennsylvanian-Early Permian Mississippi Valley-type ore pulses that deposited large sulfide minerals in the Viburnum Trend/Old Lead Belt ore districts. The δ34SCAS values range from 21.3‰ to 9.3‰, and δ18OCAS values range from +1.4‰ to -2.6‰ and show a strong covariance (R2 = 0.94). The largely wholesale replacement of Cambrian seawater sulfate signatures in these dolomites does not appear to have affected the sulfate signatures in the Mt. Simon brines even though these sulfide deposits are found in the stratigraphically equivalent Lamotte Sandstone to the southwest. On the basis of this and previous studies, greater fluid densities of the Mt. Simon brines may have prevented the

  18. Buoyancy effects on upward brine displacement caused by CO2 injection

    Energy Technology Data Exchange (ETDEWEB)

    Oldenburg, C.M.; Rinaldi, A.

    2010-01-15

    Upward displacement of brine from deep reservoirs driven by pressure increases resulting from CO{sub 2} injection for geologic carbon sequestration may occur through improperly sealed abandoned wells, through permeable faults, or through permeable channels between pinch-outs of shale formations. The concern about upward brine flow is that, upon intrusion into aquifers containing groundwater resources, the brine may degrade groundwater. Because both salinity and temperature increase with depth in sedimentary basins, upward displacement of brine involves lifting fluid that is saline but also warm into shallower regions that contain fresher, cooler water. We have carried out dynamic simulations using TOUGH2/EOS7 of upward displacement of warm, salty water into cooler, fresher aquifers in a highly idealized two-dimensional model consisting of a vertical conduit (representing a well or permeable fault) connecting a deep and a shallow reservoir. Our simulations show that for small pressure increases and/or high-salinity-gradient cases, brine is pushed up the conduit to a new static steady-state equilibrium. On the other hand, if the pressure rise is large enough that brine is pushed up the conduit and into the overlying upper aquifer, flow may be sustained if the dense brine is allowed to spread laterally. In this scenario, dense brine only contacts the lower-most region of the upper aquifer. In a hypothetical case in which strong cooling of the dense brine occurs in the upper reservoir, the brine becomes sufficiently dense that it flows back down into the deeper reservoir from where it came. The brine then heats again in the lower aquifer and moves back up the conduit to repeat the cycle. Parameter studies delineate steady-state (static) and oscillatory solutions and reveal the character and period of oscillatory solutions. Such oscillatory solutions are mostly a curiosity rather than an expected natural phenomenon because in nature the geothermal gradient prevents the

  19. Synthesis of hydroxy sodalite from coal fly ash using waste industrial brine solution.

    Science.gov (United States)

    Musyoka, Nicholas M; Petrik, Leslie F; Balfour, Gillian; Gitari, Wilson M; Hums, Eric

    2011-01-01

    The effect of using industrial waste brine solution instead of ultra pure water was investigated during the synthesis of zeolites using three South African coal fly ashes as Si feedstock. The high halide brine was obtained from the retentate effluent of a reverse osmosis mine water treatment plant. Synthesis conditions applied were; ageing of fly ash was at 47 ° C for 48 hours, and while the hydrothermal treatment temperature was set at 140 ° C for 48 hours. The use of brine as a solvent resulted in the formation of hydroxy sodalite zeolite although unconverted mullite and hematite from the fly ash feedstock was also found in the synthesis product.

  20. Examination of brine contamination risk to aquatic resources from petroleum development in the Williston Basin

    Science.gov (United States)

    Gleason, Robert A.; Thamke, Joanna N.; Smith, Bruce D.; Tangen, Brian A.; Chesley-Preston, Tara; Preston, Todd M.

    2011-01-01

    U.S. Geological Survey scientists and cooperating partners are examining the potential risk to aquatic resources (for example, wetlands, streams) by contamination from saline waters (brine) produced by petroleum development in the Williston Basin of Montana, North Dakota, and South Dakota. The primary goals of this study are to provide a science-based approach to assess potential risk of brine contamination to aquatic systems and to help focus limited monitoring and mitigation resources on the areas of greatest need. These goals will be accomplished through field investigations that quantify brine movement and risk assessments using remotely-sensed and other spatial datasets.

  1. Acoustic monitoring of sodium boiling in a liquid metal fast breeder reactor from autoregressive models

    Energy Technology Data Exchange (ETDEWEB)

    Geraldo, Issa Cherif [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Bose, Tanmoy [Indian Institute of Technology Kharagpur, Kharagpur 721302, West Bengal (India); Pekpe, Komi Midzodzi, E-mail: midzodzi.pekpe@univ-lille1.fr [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Cassar, Jean-Philippe [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Mohanty, A.R. [Indian Institute of Technology Kharagpur, Kharagpur 721302, West Bengal (India); Paumel, Kévin [CEA, DEN, Nuclear Technology Department, F-13108 Saint-Paul-lez-Durance (France)

    2014-10-15

    Highlights: • The work deals with sodium boiling detection in a liquid metal fast breeder reactor. • The authors choose to use acoustic data instead of thermal data. • The method is designed to not to be disturbed by the environment noises. • A real time boiling detection methods are proposed in the paper. - Abstract: This paper deals with acoustic monitoring of sodium boiling in a liquid metal fast breeder reactor (LMFBR) based on auto regressive (AR) models which have low computational complexities. Some authors have used AR models for sodium boiling or sodium–water reaction detection. These works are based on the characterization of the difference between fault free condition and current functioning of the system. However, even in absence of faults, it is possible to observe a change in the AR models due to the change of operating mode of the LMFBR. This sets up the delicate problem of how to distinguish a change in operating mode in absence of faults and a change due to presence of faults. In this paper we propose a new approach for boiling detection based on the estimation of AR models on sliding windows. Afterwards, classification of the models into boiling or non-boiling models is made by comparing their coefficients by two statistical methods, multiple linear regression (LR) and support vectors machines (SVM). The proposed approach takes into account operating mode information in order to avoid false alarms. Experimental data include non-boiling background noise data collected from Phenix power plant (France) and provided by the CEA (Commissariat à l’Energie Atomique et aux énergies alternatives, France) and boiling condition data generated in laboratory. High boiling detection rates as well as low false alarms rates obtained on these experimental data show that the proposed method is efficient for boiling detection. Most importantly, it shows that the boiling phenomenon introduces a disturbance into the AR models that can be clearly detected.

  2. Numerical prediction of nucleate pool boiling heat transfer coefficient under high heat fluxes

    OpenAIRE

    Pezo Milada L.; Stevanović Vladimir D.

    2016-01-01

    This paper presents CFD (Computational Fluid Dynamics) approach to prediction of the heat transfer coefficient for nucleate pool boiling under high heat fluxes. Three-dimensional numerical simulations of the atmospheric saturated pool boiling are performed. Mathematical modelling of pool boiling requires a treatment of vapor-liquid two-phase mixture on the macro level, as well as on the micro level, such as bubble growth and departure from the heating surfa...

  3. Transient measurement of temperature oscillation during noisy film boiling in superfluid helium II

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Noisy film boiling, which is characterized by a loud noise andsevere mechanical vibration, is a particular phenomenon of superfluid helium II (He II). Experiments have been conducted under various thermal conditions by varying the heating time th and the heat flux q, and the temperature oscillation during noisy film boiling is measured by the superconductor temperature sensors in order to understand the physical mechanism of noisy film boiling.

  4. EFFECTS OF LOCALIZED AQUIFER BOILING ON FLUID PRODUCTION AT CERRO PRIETO.

    Science.gov (United States)

    Truesdell, Alfred H.; D'Amore, Franco; Nieva, David

    1984-01-01

    Localized aquifer boiling in the shallow two-phase reservoir of Cerro Prieto has produced excess steam and increased electrical output. Unfortunately it has also caused near-well mineral deposition that has decreased permeability and fluid flow. Inflow of cold water has limited the extent of aquifer boiling and permeability loss. The deeper reservoir at Cerro Prieto may need injection of cold water to decrease boiling and prevent loss of production. Refs.

  5. Experimental Investigation of Coolant Boiling in a Half-Heated Circular Tube - Final CRADA Report

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Wenhua [Argonne National Lab. (ANL), Argonne, IL (United States); Singh, Dileep [Argonne National Lab. (ANL), Argonne, IL (United States); France, David M. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-11-01

    Coolant subcooled boiling in the cylinder head regions of heavy-duty vehicle engines is unavoidable at high thermal loads due to high metal temperatures. However, theoretical, numerical, and experimental studies of coolant subcooled flow boiling under these specific application conditions are generally lacking in the engineering literature. The objective of this project was to provide such much-needed information, including the coolant subcooled flow boiling characteristics and the corresponding heat transfer coefficients, through experimental investigations.

  6. Impact of pressure and temperature on CO2-brine-mica contact angles and CO2-brine interfacial tension: Implications for carbon geo-sequestration.

    Science.gov (United States)

    Arif, Muhammad; Al-Yaseri, Ahmed Z; Barifcani, Ahmed; Lebedev, Maxim; Iglauer, Stefan

    2016-01-15

    Precise characterization of wettability of CO2-brine-rock system and CO2-brine interfacial tension at reservoir conditions is essential as they influence capillary sealing efficiency of caprocks, which in turn, impacts the structural and residual trapping during CO2 geo-sequestration. In this context, we have experimentally measured advancing and receding contact angles for brine-CO2-mica system (surface roughness ∼12nm) at different pressures (0.1MPa, 5MPa, 7MPa, 10MPa, 15MPa, 20MPa), temperatures (308K, 323K, and 343K), and salinities (0wt%, 5wt%, 10wt%, 20wt% and 30wt% NaCl). For the same experimental matrix, CO2-brine interfacial tensions have also been measured using the pendant drop technique. The results indicate that both advancing and receding contact angles increase with pressure and salinity, but decrease with temperature. On the contrary, CO2-brine interfacial tension decrease with pressure and increase with temperature. At 20MPa and 308K, the advancing angle is measured to be ∼110°, indicating CO2-wetting. The results have been compared with various published literature data and probable factors responsible for deviations have been highlighted. Finally we demonstrate the implications of measured data by evaluating CO2 storage heights under various operating conditions. We conclude that for a given storage depth, reservoirs with lower pressures and high temperatures can store larger volumes and thus exhibit better sealing efficiency.

  7. Electrochemical Chloride extraction using external electrodes?

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Pedersen, Anne Juul

    2006-01-01

    Electrochemical methods for the removal of chloride from concrete have been developed and the methods are primarily designed for situations where corrosion has started due to an increased chloride concentration in the vicinity of the reinforcement. In these methods the reinforcement is used...... as the cathode. However, some unwanted side effects can occur, including alkali-silica reaction and in some cases hydrogen embrittlement. It is also suggested also to use electrochemical chloride extraction in a preventive way in constructions where chloride induced corrosion is likely to be a problem after...... a period of time, i.e. remove the chlorides before the chloride front reaches the reinforcement. If the chlorides are removed from outer few centimetres from the surface, the chloride will not reach the reinforcement and cause damage. By using the electrochemical chloride removal in this preventive way...

  8. Boiling heat transfer region with independence of the wall temperature

    Science.gov (United States)

    Mühlenbruch, G. H. D.; Schmidt, J.

    Extensive measurements of the intensive cooling of hot-rolled wires with temperatures between 1000 °C and 1100 °C are analysed. The analysis proves the existence of a convection-controlled boiling region, which has been previously observed by few authors in the case of high mass fluxes and high liquid subcooling. This region is characterised by an independence of the heat flux of the surface temperature. The heat flux depends essentially on the Reynolds number, the main influence parameter of the single phase convection, and on the liquid subcooling.

  9. Radon depletion in xenon boil-off gas

    OpenAIRE

    Bruenner, S.; Cichon, D.; Lindemann, S.; Undagoitia, T. Marrodán; Simgen, H.

    2016-01-01

    An important background in detectors using liquid xenon for rare event searches arises from the decays of radon and its daughters. We report for the first time a reduction of $^{222}$Rn in the gas phase above a liquid xenon reservoir. We show a reduction factor of $\\gtrsim 4$ for the $^{222}$Rn concentration in boil-off xenon gas compared to the radon enriched liquid phase. A semiconductor-based $\\alpha$-detector and miniaturized proportional counters are used to detect the radon. As the rado...

  10. Experimental research conception of thin liquid film boiling and evaporation

    Directory of Open Access Journals (Sweden)

    Feoktistov Dmitry V.

    2015-01-01

    Full Text Available The concept of conducting the experiments for studying thin liquid film boiling and evaporation was developed. Implementing this conception on developed experimental setup, we will obtain the data on the change of liquid film thickness in thermosiphon and temperature distribution in the liquid film, also the evaporation rate of liquid film and heat transfer coefficient change will be calculated using the measured values in the experiment. Three series of preliminary experiment were conducted. As a result, the main influencing factors and their values were defined.

  11. Nucleation, solvation and boiling of helium excimer clusters

    CERN Document Server

    Luna, Luis G Mendoza; Watkins, Mark J; Bonifaci, Nelly; Aitken, Frederic; von Haeften, Klaus

    2015-01-01

    Helium excimers generated by a corona discharge were investigated in the gas and normal liquid phases of helium as a function of temperature and pressure between 3.8 and 5.0 K and 0.2 and 5.6 bar. Intense fluorescence in the visible region showed the rotationally resolved $d^3\\Sigma_u^+ \\rightarrow b^3\\Pi_g$ transition of He$_2^*$. With increasing pressure, the rotational lines merged into single features. The observed pressure dependence of linewidths, shapes and lineshifts established phases of coexistence and separation of excimer-helium mixtures, providing detailed insight into nucleation, solvation and boiling of He$_2^*$-He$_n$ clusters.

  12. Treatment of cork boiling wastewater using chemical oxidation and biodegradation

    OpenAIRE

    Machado, Manuela Dias; Madeira, Luis M.; Nogales, Balbina; Nunes, Olga C; Manaia, Célia M.

    2006-01-01

    Three cultures were enriched from cork boiling wastewater using tannic acid as the selective carbon substrate, at 25 C and pH 7.2, 25 C and pH 4.7 and 50 C and pH 4.7. The enrichment culture obtained at neutral pH was composed of five culturable isolates, whereas from each acidic enrichment two bacterial strains were isolated. Mesophilic isolates were Gram negative bacteria belonging to the genera Klebsiella, Pseudomonas, Stenotrophomonas and Burkholderia. Thermophilic isolates we...

  13. Union job fight boiling at DOE cleanup sites

    Energy Technology Data Exchange (ETDEWEB)

    Setzer, S.W.

    1993-11-15

    The US DOE is facing a growing jurisdictional dispute over which unions will perform the majority of clean-up work at its facilities. Unions affiliated with the AFL-CIO Metal Trades Council representing operations employees at the sites believe they have a fundamental right to work. Unions in the AFL-CIO's Building and Construction Trades Dept. insist that they have a clear mandate under federal labor law and the Davis-Bacon Act. The issue has heated up in recent weeks at the policy level and is boiling in a contentious dispute at DOE's Fernald site in Ohio.

  14. Experimental and theoretical study on rapid transient nucleated boiling

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A laser heater has been used to impose a pulsed high power laser beam on a metal film inunersed in liquid to generate a very high rate of temperature rise up to 9.3 × 106K/s in the metal film. The rapid transient boiling phenomena have been observed and the temperature variations in the metal film have been measured. Theoretical calculations have been carried out with the fluctuation nucleation theory and the heat conduction theory to compare with the experimental results, and some results are reported.

  15. MTD-MFC: unified framework for investigation of diversity of boiling heat transfer curves

    Energy Technology Data Exchange (ETDEWEB)

    Shekriladze, I.G. [Georgian Technical University, Tbilisi (Georgia)], e-mail: shekri@geo.net.ge

    2009-07-01

    A keynote paper presents just the next attempt to promote a discussion of modern state of art in the field of boiling heat transfer research. It is shown how longstanding disregard of internal contradictions of applicable approaches has resulted theoretical deadlock. Alternatively, it also is shown how resolution of these contradictions opens the ways to breakthrough in boiling heat transfer theory. Basic experimental facts, physical models and correlations are reconsidered. Principal contradictions between experimental knowledge and traditional model of 'the theatre of actors' (MTA) are discussed. Crucial role of pumping effect of growing bubble (PEGB) in boiling heat transfer and hydrodynamics is shown. Basic role of control of HTC by thermodynamic conditions on nucleation sites is demonstrated and consequent model of 'the theatre of director' (MTD) is discussed. Universal MTD-based correlation of boiling HTC of all types of liquids is considered. Unified consistent research framework for developed boiling heat transfer and diverse specific boiling heat transfer regimes is outlined through supplementing MTD by so-called multifactoring concept (MFC). The latter links transition from developed boiling mode to diverse boiling curves to a phenomenon of multiplication of factors influencing HTC. The ways of further research of the boiling problem are discussed. (author)

  16. Film Boiling Heat Transfer Properties of Liquid Hydrogen in Natural Convection

    Science.gov (United States)

    Horie, Y.; Shirai, Y.; Shiotsu, M.; Matsuzawa, T.; Yoneda, K.; Shigeta, H.; Tatsumoto, H.; Hata, K.; Naruo, Y.; Kobayashi, H.; Inatani, Y.

    Film boiling heat transfer properties of LH2 for various pressures and subcooling conditions were measured by applying electric current to give an exponential heat input to a PtCo wire with a diameter of 1.2 mm submerged in LH2. The heated wire was set to be horizontal to the ground. The heat transfer coefficient in the film boiling region was higher for higher pressure and higher subcooling. The experimental results are compared with the equation of pool film boiling heat transfer. It is confirmed that the pool film boiling heat transfer coefficients in LH2 can be expressed by this equation.

  17. Study of rapid transient explosive boiling under short-pulsed laser heating

    Institute of Scientific and Technical Information of China (English)

    JIN Renxi; HUAI Xiulan; LIU Dengying

    2004-01-01

    Using acetone, ethanol, water and acetone-water mixture as test liquids, the rapid transient explosive boiling (RTEB) taking place under short-pulsed laser heating is observed in experiment. The behaviors of temperature variation are investigated via transient temperature measurement. The vapor bubble behaviors of RTEB are captured by high-speed photography, and the difference between RTEB and normal boiling is analyzed. The boiling heat transfer of RTEB is also discussed. It shows that the character of RTEB is far different from normal boiling.

  18. Pressure Fluctuation of 1/fα in the Film Boiling of He Ⅱ

    Institute of Scientific and Technical Information of China (English)

    张鹏; 村上正秀; 王如竹

    2002-01-01

    A detailed study of the pressure oscillation induced by the film boiling of He Ⅱ is presented. The film boiling state and the stability of the vapour film are determined by the governing parameter (i.e. the immersion depth). It is found that the power density spectrum of the pressure oscillation induced by the film boiling displays the 1/fα-behaviour. The exponent α was found to be within the range from one to two, which indicates the existence of self-organized criticality in the film boiling of He Ⅱ.

  19. Experimental Evidence of the Vapor Recoil Mechanism in the Boiling Crisis

    CERN Document Server

    Nikolayev, Vadim; Garrabos, Y; Beysens, D

    2016-01-01

    Boiling crisis experiments are carried out in the vicinity of the liquid-gas critical point of H2. A magnetic gravity compensation setup is used to enable nucleate boiling at near critical pressure. The measurements of the critical heat flux that defines the threshold for the boiling crisis are carried out as a function of the distance from the critical point. The obtained power law behavior and the boiling crisis dynamics agree with the predictions of the vapor recoil mechanism and disagree with the classical vapor column mechanism.

  20. Ground-Water-Flow Modeling of a Freshwater and Brine-Filled Aquifer in the Onondaga Trough, Onondaga County, New York - A Summary of Findings

    Science.gov (United States)

    Kappel, William M.; Yager, Richard M.

    2008-01-01

    In 2007, the U.S. Geological Survey (USGS) completed a hydrogeologic study that included the development of a groundwater-flow model of the glacial-drift aquifer in the Onondaga Trough near Syracuse, N.Y., which extends from the Valley Heads Moraine near Tully, N.Y., to Onondaga Lake (fig. 1). Glacial sediments within the Onondaga Trough contain freshwater, saline water, and brine, which has historically supported several chemical industries in Syracuse. The ground-water-flow model was developed as a means to assist the members of the Onondaga Lake Partnership (local, State, and Federal governmental agencies) to assess remediation plans for Onondaga Lake and the Onondaga Creek watershed. Prior to this study, in the late 1990s, very little information was known about the physical nature of the valley-fill aquifer or the quality of water within it. Acquisition of this information would help local agencies understand the interactions of fresh and saline water within the aquifer and Onondaga Lake, and would facilitate the design of proposed and ongoing remediation work in and near the lake. The USGS study characterized the geology and geochemistry of the aquifer system, estimated the rate and direction of ground-water movement, and estimated mass loadings of chloride to Onondaga Lake and its tributaries from natural and anthropogenic sources. The study required analysis of existing hydrogeologic data and drilling of new test wells to collect additional hydrogeologic data to supplement this database. A three-dimensional geologic model of the unconsolidated deposits that fill the Onondaga Trough was developed from this information. Water-quality samples were collected, and hydraulic head (water-level) measurements were made in the test wells. The water samples were analyzed for a variety of chemical constituents to determine the composition and age of saline waters within the aquifer. The geologic model, together with the water-quality and hydraulic-head data, supported

  1. Pool Boiling of FC 770 on Graphene Oxide Coatings: A Study of Critical Heat Flux and Boiling Heat Transfer Enhancement Mechanisms

    OpenAIRE

    Sayee Mohan, Kaushik

    2016-01-01

    This thesis investigates pool boiling heat transfer from bare and graphene-coated NiCr wires in a saturated liquid of FC 770, a fluorocarbon fluid. Of particular interest was the effect of graphene-oxide platelets, dip-coated onto the heater surface, in enhancing the nucleate boiling heat transfer (BHT) rates and the critical heat flux (CHF) value. In the course of the pool boiling experiment, the primary focus was on the reduction mechanism of graphene oxide. The transition from hydrophilic ...

  2. High-order Cu(II) chloro-complexes in LiCl brines: Insights from density function theory and molecular dynamics

    Science.gov (United States)

    Li, Hui-Ji; Yi, Hai-Bo; Xu, Jia-Jia

    2015-09-01

    Cu(II) complexation by chloride is relevant to the transport of copper in near-surface geologic environments, yet the existence of high-order Cu(II) chloro-complexes still remains in dispute. In this study, the structure characteristics and stabilities of [CuClx]2-xaq (x = 3, 4, 5) complexes have been investigated using density functional theory (DFT) methods and molecular dynamics (MD) simulations. [CuCl3]- and [CuCl4]2- species can both be tracked, while the [CuCl5]3-aq complex cannot be recorded during MD simulations of trace Cu2+ in chloride-rich brines. DFT calculations indicate that contact ion pair (CIP) conformers of [CuCl3]- species are less stable than its solvent separated ion pair (SSIP) conformers, in which one Cl- stays in the second coordination sphere of the centered Cu2+. MD simulations also reveal that the SSIP conformer is apt to appear in the aqueous solution than its CIP conformer. It seems that the third Cl- is more likely in the second coordination shell of center Cu2+ in [CuCl3]-. Meanwhile, the characteristic peak around 385 nm resolved in UV-Vis spectra experiments, which was attributed to the [CuCl3]- complex, could also be resulted from some SSIP structures of the [CuCl3]- complex. In MD simulations, the complex [CuCl4]2-aq is found more stable than [CuCl3]-aq. The surrounding water molecules around [CuClx]2-xaq (x = 3, 4) enhance their stabilities in Cl- brines, especially for [CuCl4]2-aq. The hydration shell of [CuCl4]2-aq species is more intact than that of [CuCl3]2-aq, and the residence time of a water molecule in the second coordination sphere of Cu ion in the [CuCl4]2-aq complex is also obviously longer than that of [CuCl3]-aq. The [CuCl4]2-aq complex can even be recorded in the less concentrated (6.33 m) Cl- solution, while the [CuCl3]-aq complex is tracked only in the 16.32 m Cl- brine. Meanwhile, the possibilities of [CuCl3]-aq and [CuCl4]2-aq complexes found in 16.32 m Cl- solutions both decrease with increasing temperature

  3. Lubiprostone: a chloride channel activator.

    Science.gov (United States)

    Lacy, Brian E; Levy, L Campbell

    2007-04-01

    In January 2006 the Food and Drug Administration approved lubiprostone for the treatment of chronic constipation in men and women aged 18 and over. Lubiprostone is categorized as a prostone, a bicyclic fatty acid metabolite of prostaglandin E1. Lubiprostone activates a specific chloride channel (ClC-2) in the gastrointestinal (GI) tract to enhance intestinal fluid secretion, which increases GI transit and improves symptoms of constipation. This article reviews the role of chloride channels in the GI tract, describes the structure, function, and pharmacokinetics of lubiprostone, and discusses clinically important data on this new medication.

  4. Conservação de filés de tilápia-do-nilo (Oreochromis niloticus em salga seca e salga úmida Nile tilapia (Oreochromis niloticus preservation by means of dry salting and saturated brine

    Directory of Open Access Journals (Sweden)

    F.S. Aiura

    2008-12-01

    Full Text Available Acompanhou-se o desenvolvimento dos processos da salga em salmoura saturada (salga úmida e salga seca de filés de tilápia-do-nilo (Oreochromis niloticus e avaliaram-se algumas características indicativas de qualidade do produto durante a estocagem. Os processos foram acompanhados por 156 horas na salga úmida e por 96 horas na salga seca, e os filés salgados foram estocados, respectivamente, por 60 e 45 dias à temperatura ambiente. Os teores máximos de cloreto nos filés (14% foram atingidos com 72 horas na salga úmida e com 36 horas na salga seca. Os filés de tilápia salgados em salmoura mantiveram as características próprias do produto por um período de 45 dias, e os submetidos à salga seca apresentaram baixo teor de umidade (6% e alta concentração de extrato etéreo (4,6%. Recomenda-se somente o processo de salga em salmoura saturada como forma de conservação dos filés de tilápia-do-nilo.The processes of salting of Nile tilapia fillets (Oreochromis niloticus submitted to saturated brine and dry salting were observed, and some characteristics that indicate the quality of the product during the storage were evaluated. The brine saturated process was followed up to 156 hours and the dry salting was followed up to 96 hours. When the salting finished, fillets were stored for 45 (dry salting and 60 days (saturated brine, respectively. The highest values for chloride in fillets (14% were reached within 72 hours in brine salting and 36 hours in dry salting. The tilapia fillets salted in brine kept the proper characteristics of the product for a period of 45 days and the fillets submitted to dry salting showed low moisture ratios (6% and a high concentration of lipids (4.6%. Thereby, it is only recommended the salting process in saturated brine to be used as a mean of conservation for Nile tilapia fillets.

  5. Long Term Electrochemical Behavior of Creviced and Non-Creviced Alloy 22 in CaCl2 + Ca(NO3)2 Brines at 155?C

    Energy Technology Data Exchange (ETDEWEB)

    Rodr?guez, M A; Stuart, M L; Rebak, R B

    2006-11-08

    Alloy 22 is a nickel base alloy highly resistant to all forms of corrosion. In very aggressive conditions (e.g. hot concentrated chloride containing brines) Alloy 22 could suffer localized attack, namely pitting and crevice corrosion. Chloride ion is known to be the most detrimental aggressive agent for Alloy 22 and is able to promote crevice corrosion when tight crevices exist in hot chloride containing solutions of different concentrations. Nitrate ion is an effective inhibitor of chloride induced crevice corrosion when present in a high enough [NO{sub 3}{sup -}]/[Cl{sup -}] ratio. The occurrence of localized corrosion in a given environment is governed by the values of the critical potential (E{sub crit}) for crevice corrosion and the corrosion potential (E{sub corr}) that the alloy may establish in the studied environment. If E{sub corr} is equal or higher than E{sub crit}, localized corrosion may be expected. This paper discusses the evolution of E{sub corr} and corrosion rate (CR) of Alloy 22 specimens in 18 m CaCl{sub 2} + 9 m Ca(NO{sub 3}){sub 2} and 18 m CaCl{sub 2} + 0.9 m Ca(NO{sub 3}){sub 2} brines at 155 C. Two types of specimens were used, polished as-welded (ASW) creviced and non-creviced specimens and as-welded plus solution heat-treated (ASW+SHT) creviced specimens. The latter contained the black annealing oxide film on the surface. Results show that, in a few immersion days E{sub corr} reached a stable value higher than the open circuit potential of a platinum electrode in 18 m CaCl{sub 2} + 9 m Ca(NO{sub 3}){sub 2} for all specimens tested. Specimens tested in this solution did not suffer any type of localized attack. On the other hand, E{sub corr} showed oscillations of up to 600 mV in 18 m CaCl{sub 2} + 0.9 m Ca(NO{sub 3}){sub 2} during the entire immersion period. These oscillations were due to pitting corrosion development. Crevice corrosion was not observed in any testing case. Corrosion rates for specimens in the latter solution ([NO{sub 3

  6. Utilization of Brine Sludge in Nonstructural Building Components: A Sustainable Approach

    Directory of Open Access Journals (Sweden)

    Mridul Garg

    2014-01-01

    Full Text Available The characterization and influence of brine sludge on the properties of cement-fly ash-sludge binders are presented. The reaction products formed during the hydration of binder provide an interlocking framework to physically encapsulate the waste particles and are responsible for the development of strength. The utilization of brine sludge in making paver blocks and bricks and the effect of sludge concentration on the engineering properties of these products are also discussed. These results clearly exhibited that brine sludge up to 35 and 25% can safely be utilized for making paver blocks and bricks, respectively. The leachability studies confirm that the metals ions and impurities in the sludge are substantially fixed in the matrix and do not readily leach from there. The utilization of brine sludge in construction materials could serve as an alternative solution to disposal and reduce pollution.

  7. Interim report for defining brine and oil threats in the Patoka River National Wildlife Refuge [2001

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The following interim report is a list of activities being performed in conjunction with the study of oil brine effects on crayfish in the Patoka River National...

  8. Brine shrimp lethality and antibacterial activity of extracts from the bark of Schleichera oleosa

    Directory of Open Access Journals (Sweden)

    Laxman Pokhrel

    2015-08-01

    Full Text Available Objective: To determine the antibacterial efficacy and brine shrimp toxicity of extracts (hexane, dichloromethane, ethyl acetate, methanol and water obtained from the bark of Schleichera oleosa. Methods: The powdered bark sample was Soxhlet extracted sequentially in hexanes, dichloromethane, ethyl acetate, methanol and water. Antibacterial evaluation was carried out by following the agar diffusion method and amoxicillin disc was used as a reference. Slightly modified Meyer’s method was used to determine the toxicity of the extracts in brine shrimps. Results: Among the nine bacterial strains tested, the methanolic and aqueous extracts showed promising antibacterial efficacy against Serratia marcescens, Escherarichia coli, Bacillus subtilis and Micrococcus luteus. None of the extracts were found significantly toxic to brine shrimps. Conclusions: Strong antibacterial activity and low brine shrimp toxicity of methanolic and aqueous extracts can provide new antibacterial compounds.

  9. Brine shrimp lethality and antibacterial activity of extracts from the bark of Schleichera oleosa

    Institute of Scientific and Technical Information of China (English)

    Laxman Pokhrel; Bigyan Sharma; Gan B Bajracharya

    2015-01-01

    Objective: To determine the antibacterial efficacy and brine shrimp toxicity of extracts (hexane, dichloromethane, ethyl acetate, methanol and water) obtained from the bark of Schleichera oleosa. Methods: The powdered bark sample was Soxhlet extracted sequentially in hexanes, dichloromethane, ethyl acetate, methanol and water. Antibacterial evaluation was carried out by following the agar diffusion method and amoxicillin disc was used as a reference. Slightly modified Meyer’s method was used to determine the toxicity of the extracts in brine shrimps. Results: Among the nine bacterial strains tested, the methanolic and aqueous extracts showed promising antibacterial efficacy against Serratia marcescens, Escherarichia coli, Bacillus subtilis and Micrococcus luteus. None of the extracts were found significantly toxic to brine shrimps. Conclusions: Strong antibacterial activity and low brine shrimp toxicity of methanolic and aqueous extracts can provide new antibacterial compounds.

  10. Chemical aspects of a brine pool at the East Flower Garden bank, northwestern Gulf of Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Brooks, J.M.; Bright, T.J.; Bernard, B.B.; Schwab, C.R.

    1979-07-01

    A small pool on the flank of the East Flower Garden bank at a depth of 72 m in the Gulf of Mexico contains anoxic, hypersaline (approx. 200 g.kg/sup -1/) water. The flux of brine into and out of the pool contributes to erosional processes on the bank. The bulk ionic composition of the brine is similar to that of the Orca Basin brine, but differences between the two in gaseous hydrocarbon and carbon isotope content indicate different modes of origin. High levels of bacterial activity in the brine are indicated by ATP (> 80 ng.liter/sup -1/), hydrogen sulfide (> 2000 ..mu..mol.liter/sup -1/), isotopically light ..sigma..CO/sub 2/ (delta/sup 13/C =-23/sup 0///sub 00/ and the apparent generaton of elemental sulfur.

  11. Interim report for defining brine and oil threats in the Patoka River National Wildlife Refuge [2002

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The following interim report is a list of activities being performed in conjunction with the study of oil brine effects on crayfish in the Patoka River National...

  12. THE BRINE SHRIMP (ARTEMIA SALINA) LETHALITY OF Brassica oleracea var. capitata

    OpenAIRE

    O.T. TÜZÜN, E. GÜRKAN, F. HIRLAK,

    2015-01-01

    This work covers up the bio-activities of the five fractions obtained from the ethanolic extract of Brassica oleracea var. capitata (Cruciferae).Key Words: Brassica oleracea var. capitata, Brine shrimp (Artemia salina)

  13. Bead Evaporator for Complete Water and Salt Recovery from Brine Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A microgravity-compatible Brine Evaporation and Mineralization System (BEMS) is proposed for 100% water recovery from highly contaminated wastewater as well as water...

  14. USE OF BRINE SHRIMP (ARTEMIA IN THE FEEDING OF STURGEON JUVENILES (ACIPENSERIDAE (REVIEW

    Directory of Open Access Journals (Sweden)

    M. Simon

    2016-06-01

    Full Text Available Purpose. To review scientific sources on the technological and biological characteristics of the use of brine shrimp (Artemia in the feeding of sturgeon juvenilse (Acipenseridae. To highlight the common biotechnological bases of the enrichment of brine shrimp with biologically active substances necessary for the full development of sturgeon juveniles. Findings. The review of scientific papers showed that the technology is the use of brine shrimp in the feeding of sturgeon speices not only had not lost its relevance in aquaculture, but also continued to evolve in response to new challenges. The review contains a description of the peculiarities of the biological structure of brine shrimp eggs and methods of their quality assessment in the field. It describes the nutritional characteristics of Artemia. It is shown that brine shrimp is the best food organism for the use in the feeding of sturgeon fingerlings. The calculation scheme for Artemia decapsulation and incubation is provided. The main technological stages of of the preparation of shrimps before their use in feeding – activation, hydration, decapsulation, incubation, dehydration were described. The effect of brine shrimp nauplia enriched with biologically active substances enriched brine shrimp on sturgeon juveniles was highlighted. Practical value. Fish farm owners search for cost-effective, easy to use, and available food that is preferred by sturgeon juveniles (Acipenseridae. Brine shrimp nauplii obtained from cysts can be readil used to feed fish just after one-day incubation. Instar I (the nauplii that just hatched and contain large yolk reserves in their body and instar II nauplii (the nauplii after first moult and with functional digestive tracts are more widely used in aquaculture, because they are easy for operation, rich in nutrients, and small, which makes them suitable for feeding fish larvae as live feed or after drying. The generalized information will be important for

  15. Study of thermal-gradient-induced migration of brine inclusions in salt. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Olander, D.R.

    1984-08-01

    Natural salt deposits, which are being considered for high-level waste disposal, contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine (the all-liquid inclusions) migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms, which is undesirable. Therefore it is important to consider the migration of brine inclusions in salt under imposed temperature gradients to properly evaluate the performance of a future salt repository for nuclear wastes. The migration velocities of the inclusions were found to be dependent on temperature, temperature gradient, and inclusion shape and size. The velocities were also dictated by the interfacial mass transfer resistance at brine/solid interface. This interfacial resistance depends on the dislocation density in the crystal, which in turn, depends on the axial compressive loading of the crystal. At low axial loads, the dependence between the velocity and temperature gradient is nonlinear. At high axial loads, the interfacial resistance is reduced and the migration velocity depends linearly on the temperature gradient. All-liquid inclusions filled with mixed brines were also studied. For gas-liquid inclusions, helium, air and argon were compared. Migration studies were also conducted on single crystallites of natural salt as well as in polycrystalline natural salt samples. The behavior of the inclusions at large-ange grain boundaries was observed.

  16. Antagonism Between Osmophilic Lactic Acid Bacteria and Yeasts in Brine Fermentation of Soy Sauce

    OpenAIRE

    NODA, FUMIO; Hayashi, Kazuya; Mizunuma, Takeji

    1980-01-01

    Brine fermentation by osmophilic lactic acid bacteria and yeasts for long periods of time is essential to produce a good quality of shoyu (Japanese fermented soy sauce). It is well known that lactic acid fermentation by osmophilic lactic acid bacteria results in the depression of alcoholic fermentation by osmophilic yeasts, but the nature of the interaction between osmophilic lactic acid bacteria and yeasts in brine fermentation of shoyu has not been revealed. The inhibitory effect of osmophi...

  17. Effect of superheat and electric field on saturated film boiling

    Science.gov (United States)

    Pandey, Vinod; Biswas, Gautam; Dalal, Amaresh

    2016-05-01

    The objective of this investigation is to study the influence of superheat temperature and applied uniform electric field across the liquid-vapor interface during film boiling using a coupled level set and volume of fluid algorithm. The hydrodynamics of bubble growth, detachment, and its morphological variation with electrohydrodynamic forces are studied considering the medium to be incompressible, viscous, and perfectly dielectric at near critical pressure. The transition in interfacial instability behavior occurs with increase in superheat, the bubble release being periodic both in space and time. Discrete bubble growth occurs at a smaller superheat whereas vapor columns form at the higher superheat values. Destabilization of interfacial motion due to applied electric field results in decrease in bubble separation distance and increase in bubble release rate culminating in enhanced heat transfer rate. A comparison of maximum bubble height owing to application of different intensities of electric field is performed at a smaller superheat. The change in dynamics of bubble growth due to increasing superheat at a high intensity of electric field is studied. The effect of increasing intensity of electric field on the heat transfer rate at different superheats is determined. The boiling characteristic is found to be influenced significantly only above a minimum critical intensity of the electric field.

  18. High Heat Flux Burnout in Subcooled Flow Boiling

    Institute of Scientific and Technical Information of China (English)

    G.P.Celata; M.Cumo; 等

    1995-01-01

    The paper reports the results of an experimental research carried out at the Heat transfer divison of the Energy Department,C.R.Casaccia,on the thermal hydraulic characterization of subcooled flow boiling CHF under typical conditions of thermonuclear fusion reactors.I.e.high liquid velocity and subcooling.The experiment was carried out exploring the following parameters:channel diameter(from 2.5to 8.0 mm),heated length(10 and 15cm) ,liquid velocity (from 2 to 40m/s),exit pressure(from atmospheric to 5.0 MPa),inlet temperature(from 30 to 80℃),channel orientation (vertical and horizontal),A maximum CHF value of 60.6MW/m2 has been obtained under the following conditions:Tin-30°,p=2.5MPa,u=40m/s,D=2.5mm(smooth channel) Turbulence promoters(helically coiled wires)have been employed to further enhance the CHF attainable with subcooled flow boiling.Helically coiled wires allow an increase of 50% of the maximum CHF obtained with smooth channels.

  19. Drag reduction of flow boiling with polymer additives

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The drag-reducing effect of polymer additive aqueous solution was investigated in flow boiling, and the polymer additives were two kinds of polyacrylamide (PAM) with relative molecular mass about 2.56×106 and 8.55×106. The frictional pressure drop was calculated according to the measured total pressure drop. The results show that the flow drag of flow boiling is reduced by adding a small amount of PAM to water when heat flux is in the range of 15.1 kW*m-2 to 47.0 kW*m-2, when the mass fraction of PAM is higher than 2.0×10-5, the drag-reducing effect is obvious. Drag-reducing effect of PAM, whose relative molecular mass is 8.55×106, is slightly better than that of 2.56×106 at the same mass fraction, and the greater the flow rate of the additive solution, the better the effect of the drag reduction.

  20. Nucleate boiling pressure drop in an annulus: Book 5

    Energy Technology Data Exchange (ETDEWEB)

    1992-11-01

    The application of the work described in this report is the production reactors at the Savannah River Site, and the context is nuclear reactor safety. The Loss of Coolant Accident (LOCA) scenario considered involves a double-ended break of a primary coolant pipe in the reactor. During a LOCA, the flow through portions of the reactor may reverse direction or be greatly reduced, depending upon the location of the break. The reduced flow rate of coolant (D{sub 2}O) through the fuel assembly channels of the reactor -- downflow in this situation -- can lead to boiling and to the potential for flow instabilities which may cause some of the fuel assembly channels to overheat and melt. That situation is to be avoided. The experimental approach is to provide a test annulus which simulates geometry, materials, and flow conditions in a Mark-22 fuel assembly (Coolant Channel 3) to the extent possible. The key analysis approaches are: To compare the minima in the measured demand curves with analytical criteria, in particular the Saha-Zuber (1974) model; and to compare the pressure and temperature as a function of length in the annulus with an integral model for flow boiling in a heated channel. Nineteen test series and a total of 178 tests were performed. Testing addressed the effects of: Heat flux; pressure; helium gas; power tilt; ribs; asymmetric heat flux. This document consists solely of the plato file index from 11/87 to 11/90.

  1. Effect of size sprinkled heat exchange surface on developing boiling

    Directory of Open Access Journals (Sweden)

    Petr Kracík

    2016-06-01

    Full Text Available This article presents research of sprinkled heat exchangers. This type of research has become rather topical in relation to sea water desalination. This process uses sprinkling of exchangers which rapidly separates vapour phase from a liquid phase. Applications help better utilize low-potential heat which is commonly wasted in utility systems. Low-potential heat may increase utilization of primary materials. Our ambition is to analyse and describe the whole sprinkled exchanger. Two heat exchangers were tested with a similar tube pitch: heat exchanger no. 1 had a four-tube bundle and heat exchanger no. 2 had eight-tube bundle. Efforts were made to maintain similar physical characteristics. They were tested at two flow rates (ca 0.07 and 0.11 kg s−1 m−1 and progress of boiling on the bundle was observed. Initial pressure was ca 10 kPa (abs at which no liquid was boiling at any part of the exchanger; the pressure was then lowered. Other input parameters were roughly similar for both flow rates. Temperature of heating water was ca 50°C at a constant flow rate of ca 7.2 L min−1. Results of our experiments provide optimum parameters for the given conditions for both tube bundles.

  2. Water flow boiling behaviors in hydrophilic and hydrophobic microchannels

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Chiwoong; Yu, Dongin; Kim, Moohwan [Pohang University of Science and Technology (Korea, Republic of). Dept. of Mechanical Engineering

    2009-07-01

    The wettability is one of issues on two-phase flow in a microchannel. However, previous studies of wettability effect on two-phase flow have conducted only isothermal condition. Moreover, most studies have used conventional micro/mini-tubes due to difficulties of their fabrication. The objective of our study is to understand the wettability effect on flow boiling in a rectangular microchannel. In the first, new micro-electro-mechanical-system (MEMS) fabrication technique was developed to obtain a single glass rectangular microchannel and localized six micro heaters. A photosensitive glass was used as base material. The photosensitive glass is hydrophilic, so the hydrophobic microchannel was prepared by coating SAM, flow boiling experiments were conducted in hydrophilic and hydrophobic microchannels with micro heaters. The experiment range was the mass flux of 25 and 75 kg/m{sup 2}s, the heat flux of 30 - 430 k W/m2 and quality of 0 - 0.3. A working fluid was de-ionized and degassed water. The local heat transfer coefficient was evaluated at the local micro heater section. Also, flow regimes in the microchannel were visualized by using a high-speed camera with a long-distance microscope. Heat transfer was analyzed with visualization results. Heat transfer in the hydrophobic microchannel was enhanced by higher nucleation site density and delayed local dryout. The pressure drop in the hydrophobic microchannel was higher than that in the hydrophilic microchannel. (author)

  3. Experimental research on flash boiling spray of dimethyl ether

    Science.gov (United States)

    Zhang, Peng

    2014-12-01

    The high-speed digital imaging technique is applied to observe the developing process of flash boiling spray of dimethyl ether at low ambient pressure, and the effects of nozzle opening pressure and nozzle hole diameter on the spray shape, spray tip penetration and spray angle during the injection are investigated. The experimental results show that the time when the vortex ring structure of flash boiling spray forms and its developing process are determined by the combined action of the bubble growth and breakup in the spray and the air drag on the leading end of spray; with the enhancement of nozzle opening pressure, the spray tip penetration increases and the spray angle decreases. The influence of nozzle hole diameter on the spray tip penetration is relatively complicated, the spray tip penetration is longer with a smaller nozzle hole diameter at the early stage of injection, while the situation is just opposite at the later stage of injection. This paper establishes that the variation of spray angle is consistent with that of nozzle hole diameter.

  4. Subcooled pool boiling on thin wire in microgravity

    Science.gov (United States)

    Zhao, J. F.; Wan, S. X.; Liu, G.; Yan, N.; Hu, W. R.

    2009-01-01

    A new set of experimental data of subcooled pool boiling on a thin wire in microgravity aboard the 22nd Chinese recoverable satellite is reported in the present paper. The temperature-controlled heating method is used. The results of the experiments in normal gravity before and after the flight experiment are also presented, and compared with those in microgravity. The working fluid is degassed R113 at 0.1 MPa and subcooled by 26C nominally. A thin platinum wire of 60μm in diameter and 30 mm in length is simultaneously used as heater and thermometer. It is found that the heat transfer of nucleate pool boiling is slightly enhanced in microgravity comparing with those in normal gravity. It is also found that the correlation of Lienhard and Dhir can predict the CHF with good agreement, although the range of the dimensionless radius is extended by three or more decades above the originally set limit. Three critical bubble diameters are observed in microgravity, which divide the observed vapor bubbles into four regimes with different sizes. Considering the Marangoni effect, a qualitative model is proposed to reveal the mechanism underlying the bubble departure processes, and a quantitative agreement can also be acquired.

  5. Experimental Research on Flash Boiling Spray of Dimethyl Ether

    Institute of Scientific and Technical Information of China (English)

    Peng Zhang

    2014-01-01

    The high-speed digital imaging technique is applied to observe the developing process of flash boiling spray of dimethyl ether at low ambient pressure, and the effects of nozzle opening pressure and nozzle hole diameter on the spray shape, spray tip penetration and spray angle during the injection are investigated. The experimental results show that the time when the vortex ring structure of flash boiling spray forms and its developing process are determined by the combined action of the bubble growth and breakup in the spray and the air drag on the leading end of spray;with the enhancement of nozzle opening pressure, the spray tip penetration increases and the spray angle decreases. The influence of nozzle hole diameter on the spray tip penetration is relatively complicated, the spray tip penetration is longer with a smaller nozzle hole diameter at the early stage of injection, while the situation is just opposite at the later stage of injection. This paper establishes that the variation of spray angle is consistent with that of nozzle hole diameter.

  6. A heat transfer model for slug flow boiling within microchannels

    Science.gov (United States)

    Magnini, Mirco; Thome, John

    2016-11-01

    We propose a novel physics-based model for the fluid mechanics and heat transfer associated with slug flow boiling in horizontal circular microchannels, to update the widely used three-zone model for the design of multi-microchannel evaporators. The flow is modelled as the cyclic passage of a liquid slug, an elongated bubble which traps a thin liquid film against the channel wall, and a dry vapor plug. The capillary flow theory, extended to incorporate evaporation effects, is applied to estimate the bubble velocity along the channel. A liquid film thickness prediction method considering bubble proximity effects, which may limit the radial extension of the film, is included. Theoretical heat transfer models accounting for the thermal inertia of the liquid film and for the recirculating flow within the liquid slug are utilized. The heat transfer model is compared to experimental data taken from three independent studies: 833 slug flow boiling data points covering R134a, R245fa and R236fa and channel diameters from 0.4 mm to 1 mm. The new model predicts more than 80% of the database to within +/- 30 % and it represents an important step toward a complete physics-based modelling of bubble dynamics and heat transfer within microchannels under evaporating flow conditions.

  7. Radiolysis effects in sub-cooled nucleate boiling

    Energy Technology Data Exchange (ETDEWEB)

    Dickinson, S.; Henshaw, J.; Tuson, A.; Sims, H.E. [AEA Technology (United Kingdom)

    2002-07-01

    A hydrogen depleted region may form in the water during bubble formation when boiling occurs in a PWR. This would arise from stripping of gases into the steam phase. The depleted water may then become oxidising due to radiolysis forming H{sub 2}O{sub 2}. The presence of radiolytic oxidising conditions is one of the mechanisms proposed to explain deposits formed in Axial Offset Anomalies. This work describes a model that has been developed to examine this behaviour. The model deals with bubble growth and material transport as well as the radiolysis chemistry. The model simulates diffusion of species through the gas/liquid boundary layer. The appropriate mass conservation equations for this problem are described and the results of their numerical solution discussed. This model indicates the importance of the assumed boundary conditions on the results of the calculations. These boundary conditions are discussed in detail and the most appropriate ones for the actual reactor situation are outlined. The conclusion of this modelling study is that at normal PWR operating conditions of 40 cc H{sub 2} (STP) kg{sup -1} it is unlikely that radiolysis in a subcooled boiling region would be important. The situation is more ambiguous at the 1 to 5 cc H{sub 2} (STP) kg{sup -1} range. (author)

  8. Comparison of the Wear Behavior of UHMWPE Lubricated by Human Plasma and Brine

    Institute of Scientific and Technical Information of China (English)

    WANG Shi-bo; GE Shi-rong; NORM Gitis; MICHAEL Vinogradov; XIAO Jun

    2007-01-01

    The effect of plasma and brine lubricants on the friction and wear behavior of UHMWPE were studied by using the geometry of a Si3N4 ball sliding on a UHMWPE disc under patterns of uni-directional reciprocation and bi-directional sliding motions. The worn surface and wear particles produced in these two lubricants were analyzed. Sliding motion pattern affected the friction coefficients lubricated with plasma, while seldom affected that lubricated with brine. UHMWPE lubricated with plasma showed about half of the wear rate of that lubricated with brine. The two rates were 0.75 pg/m and 2.19 pg/m for the two motion patterns, respectively. However, wear particles generated in plasma included a greater amount of small particles, compared to that in brine. In uni-directional reciprocation, the main wear mechanism is ploughing both in plasma and in brine. In bi-directional sliding modes, the significant characteristic is ripples on the worn surface in plasma, while there are oriented fibers on the worn surface in brine.

  9. Numerical simulations of lab-scale brine-water mixing experiments.

    Energy Technology Data Exchange (ETDEWEB)

    Khalil, Imane; Webb, Stephen Walter

    2006-10-01

    Laboratory-scale experiments simulating the injection of fresh water into brine in a Strategic Petroleum Reserve (SPR) cavern were performed at Sandia National Laboratories for various conditions of injection rate and small and large injection tube diameters. The computational fluid dynamic (CFD) code FLUENT was used to simulate these experiments to evaluate the predictive capability of FLUENT for brine-water mixing in an SPR cavern. The data-model comparisons show that FLUENT simulations predict the mixing plume depth reasonably well. Predictions of the near-wall brine concentrations compare very well with the experimental data. The simulated time for the mixing plume to reach the vessel wall was underpredicted for the small injection tubes but reasonable for the large injection tubes. The difference in the time to reach the wall is probably due to the three-dimensional nature of the mixing plume as it spreads out at the air-brine or oil-brine interface. The depth of the mixing plume as it spreads out along the interface was within a factor of 2 of the experimental data. The FLUENT simulation results predict the plume mixing accurately, especially the water concentration when the mixing plume reaches the wall. This parameter value is the most significant feature of the mixing process because it will determine the amount of enhanced leaching at the oil-brine interface.

  10. [Headspace GC/MS analysis of residual vinyl chloride and vinylidene chloride in polyvinyl chloride and polyvinylidene chloride products].

    Science.gov (United States)

    Ohno, Hiroyuki; Mutsuga, Motoh; Kawamura, Yoko; Suzuki, Masako; Aoyama, Taiki

    2005-02-01

    A headspace GC/MS analysis method for the simultaneous determination of residual vinyl chloride (VC) and vinylidene chloride (VDC) in polyvinyl chloride (PVC) and polyvinylidene chloride (PVDC) products was developed. A test sample was swelled overnight with N,N-dimethylacetamide in a sealed vial. The vial was incubated for 1 hour at 90 degrees C, then the headspace gas was analyzed by GC/MS using a PLOT capillary column. The recoveries from spiked PVC and PVDC samples were 90.0-112.3% for VC and 85.2-108.3% for VDC. The determination limits were 0.01 microg/g for VC and 0.06/microg/g for VDC, respectively. By this method, VC was detected in two PVC water supply pipes at the levels of 0.61 and 0.01 microg/g. On the other hand, VC and VDC were not detected in any of the food container-packages or toys tested.

  11. 1,5-Diaminotetrazolium chloride

    Directory of Open Access Journals (Sweden)

    Ling-Qiao Meng

    2010-04-01

    Full Text Available The title compound, CH5N6+·Cl−, crystallized with two indepedent 1,5-diaminotetrazolium cations and two independent chloride anions in the asymmetric unit. In the crystal, there are a number of N—H...Cl hydrogen-bonding interactions, which generate a three-dimensional network.

  12. Chloride : The queen of electrolytes?

    NARCIS (Netherlands)

    Berend, Kenrick; van Hulsteijn, Leonard Hendrik; Gans, Rijk O. B.

    2012-01-01

    Background: Channelopathies, defined as diseases that are caused by mutations in genes encoding ion channels, are associated with a wide variety of symptoms and have been documented extensively over the past decade. In contrast, despite the important role of chloride in serum, textbooks in general d

  13. 21 CFR 173.375 - Cetylpyridinium chloride.

    Science.gov (United States)

    2010-04-01

    ... CONSUMPTION Specific Usage Additives § 173.375 Cetylpyridinium chloride. Cetylpyridinium chloride (CAS Reg. No... Nutrition's Library, Food and Drug Administration, 5100 Paint Branch Pkwy., College Park, MD 20740, or...

  14. High-speed infrared thermography for the measurement of microscopic boiling parameters on micro- and nano-structured surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Park, Youngjae; Kim, Hyungdae [Kyung Hee Univ., Yongin (Korea, Republic of); Kim, Hyungmo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Joonwon [POSTECH, Pohang (Korea, Republic of)

    2014-10-15

    Micro- and nano-scale structures on boiling surfaces can enhance nucleate boiling heat transfer coefficient (HTC) and critical heat flux (CHF). A few studies were conducted to explain the enhancements of HTC and CHF using the microscopic boiling parameters. Quantitative measurements of microscopic boiling parameters are needed to understand the physical mechanism of the boiling heat transfer augmentation on structured surfaces. However, there is no existing experimental techniques to conveniently measure the boiling parameters on the structured surfaces because of the small (boiling on micro- and nano-structured surfaces. The visualization results are analyzed to obtain the microscopic boiling parameters. Finally, quantitative microscopic boiling parameters are used to interpret the enhancement of HTC and CHF. In this study, liquid-vapor phase distributions of each surface were clearly visualized by IR thermography during the nucleate boiling phenomena. From the visualization results, following microscopic boiling parameters were quantitatively measured by image processing. - Number density of dry patch, NDP IR thermography technique was demonstrated by nucleate pool boiling experiments with M- and N surfaces. The enhancement of HTC and CHF could be explained by microscopic boiling parameters.

  15. Actinide biocolloid formation in brine by halophilic bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Gillow, J.B.; Francis, A.J.; Dodge, C.J. [Brookhaven National Lab., Upton, NY (United States); Harris, R.; Beveridge, T.J. [Univ. of Guelph, Ontario (Canada); Brady, P.V.; Papenguth, H.W. [Sandia National Labs., Albuquerque, NM (United States)

    1998-12-31

    The authors examined the ability of a halophilic bacterium (WIPP 1A) isolated from the Waste Isolation Pilot Plant (WIPP) site to accumulate uranium in order to determine the potential for biocolloid facilitated actinide transport. The bacterial cell surface functional groups involved in the complexation of the actinide were determined by titration. Uranium, added as uranyl nitrate, was removed from solution at pH 5 by cells but at pH 7 and 9 very little uranium was removed due to its limited solubility. Although present as soluble species, uranyl citrate at pH 5, 7, and 9, and uranyl carbonate at pH 9 were not removed by the bacterium because they were not bioavailable due to their neutral or negative charge. Addition of uranyl EDTA to brine at pH 5, 7, and 9 resulted in the immediate precipitation of U. Transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS) analysis revealed that uranium was not only associated with the cell surface but also accumulated intracellularly as uranium-enriched granules. Extended X-ray absorption fine structure (EXAFS) analysis of the bacterial cells indicated the bulk sample contained more than one uranium phase. Nevertheless these results show the potential for the formation of actinide bearing bacterial biocolloids that are strictly regulated by the speciation and bioavailability of the actinide.

  16. ACTINIDE BIOCOLLOID FORMATION IN BRINE BY HALOPHILIC BACTERIA

    Energy Technology Data Exchange (ETDEWEB)

    GILLOW,J.B.; FRANCIS,A.J.; DODGE,C.J.; HARRIS,R.; BEVERIDGE,T.J.; BRADY,P.B.; PAPENGUTH,H.W.

    1998-11-09

    The authors examined the ability of a halophilic bacterium (WIPP 1A) isolated from the Waste Isolation Pilot Plant (WIPP) site to accumulate uranium in order to determine the potential for biocolloid facilitated actinide transport. The bacterial cell surface functional groups involved in the complexation of the actinide were determined by titration. Uranium, added as uranyl nitrate, was removed from solution at pH 5 by cells but at pH 7 and 9 very little uranium was removed due to its limited solubility. Although present as soluble species, uranyl citrate at pH 5, 7, and 9, and uranyl carbonate at pH 9 were not removed by the bacterium because they were not bioavailable due to their neutral or negative charge. Addition of uranyl EDTA to brine at pH 5, 7, and 9 resulted in the immediate precipitation of U. Transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS) analysis revealed that uranium was not only associated with the cell surface but also accumulated intracellularly as uranium-enriched granules. Extended X-ray absorption fine structure (EXAFS) analysis of the bacterial cells indicated the bulk sample contained more than one uranium phase. Nevertheless these results show the potential for the formation of actinide bearing bacterial biocolloids that are strictly regulated by the speciation and bioavailability of the actinide.

  17. Actinide Biocolloid Formation in Brine by Halophilic Bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Gillow, J.B.; Francis, A.J.; Dodge, C.J.; Harris, R.; Beveridge, T.J.; Brady, P.V.; Papenguth, H.W.

    1999-07-28

    We examined the ability of a halophilic bacterium (WFP 1A) isolated from the Waste Isolation Pilot Plant (WIPP) site to accumulate uranium in order to determine the potential for biocolloid facilitated actinide transport. The bacterial cell Surface functional groups involved in the complexation of the actinide were determined by titration. Uranium, added as uranyl nitrate, was removed from solution at pH 5 by cells but at pH 7 and 9 very little uranium was removed due to its limited volubility. Although present as soluble species, uranyl citrate at pH 5, 7, and 9, and uranyl carbonate at pH 9 were not removed by the bacterium because they were not bioavailable due to their neutral or negative charge. Addition of uranyl EDTA to brine at pH 5, 7, and 9 resulted in the immediate precipitation of U. Transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS) analysis revealed that uranium was not only associated with the cell surface but also accumulated intracellulary as uranium-enriched granules. Extended X-ray absorption fine structure (EXAFS) analysis, of the bacterial cells indicated the bulk sample contained more than one uranium phase. Nevertheless these results show the potential for the formation of actinide bearing bacterial biocolloids that are strictly regulated by the speciation and bioavailability of the actinide.

  18. Progress of Carbonation in Chloride Contaminated Concretes

    OpenAIRE

    Wang, Yaocheng; Basheer, P. A.M.; Nanukuttan, S; Bai, Y.

    2016-01-01

    Concretes used in marine environment are generally under the cyclic effect of CO2 and chloride ions (Cl-). To date, the influence of carbonation on ingress of chloride ions in concretes has been widely studied; in comparison, study on the influence of Cl- on the progress of carbonation is limited. During the study, concretes were exposed to independent and combined mechanisms of carbonation and chloride ingress regimes. Profiles of apparent pH and chloride concentration were used to indicate ...

  19. Microbial reductive dehalogenation of vinyl chloride

    Energy Technology Data Exchange (ETDEWEB)

    Spormann, Alfred M [Stanford, CA; Muller, Jochen A [Baltimore, MD; Rosner, Bettina M [Berlin, DE; Von Abendroth, Gregory [Mannheim, DE; Meshulam-Simon, Galit [Los Angeles, CA; McCarty, Perry L [Stanford, CA

    2014-02-11

    Compositions and methods are provided that relate to the bioremediation of chlorinated ethenes, particularly the bioremediation of vinyl chloride by Dehalococcoides-like organisms. An isolated strain of bacteria, Dehalococcoides sp. strain VS, that metabolizes vinyl chloride is provided; the genetic sequence of the enzyme responsible for vinyl chloride dehalogenation; methods of assessing the capability of endogenous organisms at an environmental site to metabolize vinyl chloride; and a method of using the strains of the invention for bioremediation.

  20. Introduction of image analysis for the quantification of the boiling flow heat transfer

    NARCIS (Netherlands)

    Ferret, C.; Falk, L.; d'Ortona, U.; Chenu, A.; Veenstra, T.T.

    2004-01-01

    Heat transfer performances for non-boiling and boiling flow of a micro-vaporizer have been measured by standard methods (temperatures, flow rates, effective power input). The study was carried out for laminar flow (Re<25) in silicon micro-channels (5 mm×3 cm×200 μm) filled with ordered obstacles to

  1. Chronic consumers of boiled coffee have elevated serum levels of lipoprotein(a).

    NARCIS (Netherlands)

    Urgert, R.; Weusten-van der Wouw, M.P.M.E.; Hovenier, R.; Lund-Larsen, P.G.; Katan, M.B.

    1996-01-01

    OBJECTIVES: Lipoprotein(a) consists of an LDL-particle attached to apolipoprotein(a), which is made by the liver. Diterpenes present in boiled coffee raise serum levels of LDL cholesterol and of the liver enzyme alanine aminotransferase in man. We investigated the association between intake of boile

  2. 77 FR 38338 - Dairyland Power Cooperative; La Crosse Boiling Water Reactor Exemption From Certain Security...

    Science.gov (United States)

    2012-06-27

    ... COMMISSION Dairyland Power Cooperative; La Crosse Boiling Water Reactor Exemption From Certain Security Requirements 1.0 Background The La Crosse Boiling Water Reactor (LACBWR) is owned and was operated by the Dairyland Power Cooperative (DPC). The LACBWR was a nuclear power plant of nominal 50 Mw electrical...

  3. The effects of boiling on the allergenic properties of tropomyosin of shrimp (litopenaeus vannamei).

    Science.gov (United States)

    Shrimp play an important role in human nutrition, and is responsible for severe hypersensitivity reactions. The thermal stability of raw and boiled shrimp tropomyosins (TM) has never been reported. The aims of the study were to compare the stability of raw and boiled shrimp TM of Litopenaeus vanname...

  4. 77 FR 27097 - LaCrosse Boiling Water Reactor, Exemption From Certain Requirements, Vernon County, WI

    Science.gov (United States)

    2012-05-08

    ... COMMISSION LaCrosse Boiling Water Reactor, Exemption From Certain Requirements, Vernon County, WI AGENCY...) requesting exemptions from certain security requirements in Title 10 of the Code Federal Regulations (10 CFR) 73.55, for the LaCrosse Boiling Water Reactor (LACBWR). This Environmental Assessment (EA) has...

  5. Thermodynamic and Gasdynamic Aspects of a Boiling Liquid Expanding Vapour Explosion

    NARCIS (Netherlands)

    Xie, M.

    2013-01-01

    The risk of explosion due to rupture of a tank filled with pressurized liquefied gas (PLG) is one of the risks to be considered in the context of studies on tunnel safety. When a vessel containing liquid well above its boiling point at normal atmospheric pressure fails catastrophically a Boiling Liq

  6. Microwave super-heated boiling of organic liquids: Origin, effect and application

    NARCIS (Netherlands)

    Chemat, F.; Esveld, E.

    2001-01-01

    This paper reports the state of the art of the microwave super-heated boiling phenomenon. When a liquid is heated by microwaves, the temperature increases rapidly to reach a steady temperature while refluxing. It happens that this steady state temperature can be up to 40 K higher than the boiling po

  7. Experimental analysis of nanofluid pool boiling heat transfer in copper bead packed porous layers

    Science.gov (United States)

    Chen, Wei; Wang, Ji

    2017-03-01

    Coupling the nanofluid as working fluid and the copper beads packed porous structure on heating surface were employed to enhance the pool boiling heat transfer by changing the fluid properties with the adjunction of nanoparticles in liquid and altering the heating surface with a bead porous layer. Due to the higher thermal conductivity, the copper beads served as an extended heating surface and the boiling nucleation sites rose, but the flow resistance increased. The CuO-water and SiO2-water nanofluids as well as the pure water were respectively employed as working fluids in the pool boiling experiments. Comparing with the base fluid of water, the higher thermal conductivity and lower surface tension occur in the nanofluids and those favor the boiling heat transfer, but the higher viscosity and density of nanofluids serve as deteriorative factors. So, the concentration region of the nanofluids should be chosen properly. The maximum relative error between the collected experimental data of the pure water on a flat surface and the theoretical prediction of pool boiling using the Rohsenow correlation was less than 12 %. The comparisons of the pool boiling heat transfer characteristics were also conducted between the pure water and the nanofluids respectively on the horizontal flat surface and on the heating surface packed with a copper bead porous layer. Besides, the boiling bubble generation, integration and departure have a great affect on the pool boiling and were recorded with a camera in the bead stacked porous structures at different heat flux.

  8. The cholesterol-raising factor from boiled coffee does not pass a paper filter.

    NARCIS (Netherlands)

    Dusseldorp, van M.; Katan, M.B.; Vliet, van T.; Demacker, P.N.M.; Stalenhoef, A.F.H.

    1991-01-01

    Previous studies have indicated that consumption of boiled coffee raises total and low density lipoprotein (LDL) cholesterol, whereas drip-filtered coffee does not. We have tested the effect on serum lipids of consumed coffee that was first boiled and then filtered through commercial paper coffee fi

  9. Quantifying Salinization of the Upper-Middle Rio Grande Using a Basin-Scale Water and Chloride Mass Balance Model

    Science.gov (United States)

    Mills, S. K.; Phillips, F. M.; Hogan, J. F.; Hendrickx, J. M.

    2002-12-01

    The Rio Grande is clearly undergoing salinization, manifested by a 50-fold increase in total dissolved solids content between its headwaters in Colorado and the U.S.-Mexico border. To elucidate the causes of this salinization, we conducted an eight-day synoptic sampling campaign in August 2001. This sampling included the river, its major tributaries, and major irrigation drain inflows. Along 1200 km between the river headwaters in Colorado and Fort Quitman, Texas, we collected 110 water samples with an average interval of ~10 km between sampling locales. In the laboratory, samples were analyzed for major constituents including chloride, as well as for bromide and the 36Cl/Cl ratio. Isotopic fingerprinting using the 36Cl/Cl ratio indicates that meteoric waters and deep sedimentary brines respectively account for most of the water and most of the salt inflow to the Rio Grande. The meteoric end member has a 36Cl/Cl ratio of 1100 and a Cl/Br ratio of 30; the brine end member has a 36Cl/Cl ratio of 35 and a Cl/Br ratio of 1150. Using these end member chemistries with USGS stream flow gauging data, we constructed a water- and salt- instantaneous mass balance model of the Rio Grande for the eight-day sampling interval. This model indicates that most water losses from the Rio Grande are due to evaporation from Elephant Butte reservoir, open water evaporation from irrigation ditches, and evapotranspiration of riparian and ditch-bank vegetation. The model also emphasizes the significance of salt input due to deep brine discharge to the river, particularly at the downstream ends of local sedimentary basins of the Rio Grande rift. The Rio Grande receives a smaller amount of salt from saline drains near El Paso, which may be acquiring salt from deep brine discharge as they cross over faults or other structural fluid conduits.

  10. Theoretical modeling of CHF for near-saturated pool boiling and flow boiling from short heaters using the interfacial lift-off criterion

    Energy Technology Data Exchange (ETDEWEB)

    Mudawar, I.; Galloway, J.E.; Gersey, C.O. [Purdue Univ., West Lafayette, IN (United States)] [and others

    1995-12-31

    Pool boiling and flow boiling were examined for near-saturated bulk conditions in order to determine the critical heat flux (CHF) trigger mechanism for each. Photographic studies of the wall region revealed features common to both situations. At fluxes below CHF, the vapor coalesces into a wavy layer which permits wetting only in wetting fronts, the portions of the liquid-vapor interface which contact the wall as a result of the interfacial waviness. Close examination of the interfacial features revealed the waves are generated from the lower edge of the heater in pool boiling and the heater`s upstream region in flow boiling. Wavelengths follow predictions based upon the Kelvin-Helmholtz instability criterion. Critical heat flux in both cases occurs when the pressure force exerted upon the interface due to interfacial curvature, which tends to preserve interfacial contact with the wall prior to CHF, is overcome by the momentum of vapor at the site of the first wetting front, causing the interface to lift away from the wall. It is shown this interfacial lift-off criterion facilitates accurate theoretical modeling of CHF in pool boiling and in flow boiling in both straight and curved channels.

  11. 21 CFR 184.1426 - Magnesium chloride.

    Science.gov (United States)

    2010-04-01

    ... mineral bischofite. It is prepared by dissolving magnesium oxide, hydroxide, or carbonate in aqueous... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Magnesium chloride. 184.1426 Section 184.1426 Food... Specific Substances Affirmed as GRAS § 184.1426 Magnesium chloride. (a) Magnesium chloride (MgC12·6H2O,...

  12. Cystic Fibrosis (CF): Chloride Sweat Test

    Science.gov (United States)

    ... Old Feeding Your 1- to 2-Year-Old Cystic Fibrosis (CF) Chloride Sweat Test KidsHealth > For Parents > Cystic Fibrosis (CF) Chloride Sweat Test Print A A A ... It Is A chloride sweat test helps diagnose cystic fibrosis (CF) , an inherited disorder that makes kids sick ...

  13. 75 FR 33824 - Barium Chloride From China

    Science.gov (United States)

    2010-06-15

    ... COMMISSION Barium Chloride From China Determination On the basis of the record\\1\\ developed in the subject... order on barium chloride from China would be likely to lead to continuation or recurrence of material... Barium Chloride from China: Investigation No. 731-TA-149 (Third Review). By order of the...

  14. 75 FR 19657 - Barium Chloride From China

    Science.gov (United States)

    2010-04-15

    ... COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Notice of... chloride from China. SUMMARY: The Commission hereby gives notice that it will proceed with a full review... revocation of the antidumping duty order on barium chloride from China would be likely to lead...

  15. 21 CFR 172.180 - Stannous chloride.

    Science.gov (United States)

    2010-04-01

    ... Preservatives § 172.180 Stannous chloride. The food additive stannous chloride may be safely used for color... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Stannous chloride. 172.180 Section 172.180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR...

  16. Predictive modeling of selenium accumulation in brine shrimp in saline environments.

    Science.gov (United States)

    Byron, Earl R; Ohlendorf, Harry M; Redman, Aaron; Adams, William J; Marden, Brad; Grosell, Martin; Brooks, Marjorie L

    2011-07-01

    Great Salt Lake, Utah, is a large, terminal, hypersaline lake consisting of a northern more saline arm and a southern arm that is less saline. The southern arm supports a seasonally abundant fauna of low diversity consisting of brine shrimp (Artemia franciscana), 7 species of brine flies, and multiple species of algae. Although fish cannot survive in the main body of the lake, the lake is highly productive, and brine shrimp and brine fly populations support large numbers of migratory waterfowl and shorebirds, as well as resident waterfowl, shorebirds, and gulls. Selenium and other trace elements, metals, and nutrients are contaminants of concern for the lake because of their concentrations in municipal and industrial outfalls and runoff from local agriculture and the large urban area of Salt Lake City. As a consequence, the State of Utah recently recommended water quality standards for Se for the southern arm of Great Salt Lake based on exposure and risk to birds. The tissue-based recommendations (as measured in bird eggs) were based on the understanding that Se toxicity is predominately expressed through dietary exposure, and that the breeding shorebirds, waterfowl, and gulls of the lake are the receptors of most concern. The bird egg-based recommended standards for Se require a model to link bird egg Se concentrations to their dietary concentrations and water column values. This study analyzes available brine shrimp tissue Se data from a variety of sources, along with waterborne and water particulate (potential brine shrimp diet) Se concentrations, in an attempt to develop a model to predict brine shrimp Se concentrations from the Se concentrations in surrounding water. The model can serve as a tool for linking the tissue-based water quality standards of a key dietary item to waterborne concentrations. The results were compared to other laboratory and field-based models to predict brine shrimp tissue Se concentrations from ambient water and their diet. No

  17. High conversion pressurized water reactor with boiling channels

    Energy Technology Data Exchange (ETDEWEB)

    Margulis, M., E-mail: maratm@post.bgu.ac.il [The Unit of Nuclear Engineering, Ben Gurion University of the Negev, POB 653, Beer Sheva 84105 (Israel); Shwageraus, E., E-mail: es607@cam.ac.uk [Department of Engineering, University of Cambridge, CB2 1PZ Cambridge (United Kingdom)

    2015-10-15

    Highlights: • Conceptual design of partially boiling PWR core was proposed and studied. • Self-sustainable Th–{sup 233}U fuel cycle was utilized in this study. • Seed-blanket fuel assembly lattice optimization was performed. • A coupled Monte Carlo, fuel depletion and thermal-hydraulics studies were carried out. • Thermal–hydraulic analysis assured that the design matches imposed safety constraints. - Abstract: Parametric studies have been performed on a seed-blanket Th–{sup 233}U fuel configuration in a pressurized water reactor (PWR) with boiling channels to achieve high conversion ratio. Previous studies on seed-blanket concepts suggested substantial reduction in the core power density is needed in order to operate under nominal PWR system conditions. Boiling flow regime in the seed region allows more heat to be removed for a given coolant mass flow rate, which in turn, may potentially allow increasing the power density of the core. In addition, reduced moderation improves the breeding performance. A two-dimensional design optimization study was carried out with BOXER and SERPENT codes in order to determine the most attractive fuel assembly configuration that would ensure breeding. Effects of various parameters, such as void fraction, blanket fuel form, number of seed pins and their dimensions, on the conversion ratio were examined. The obtained results, for which the power density was set to be 104 W/cm{sup 3}, created a map of potentially feasible designs. It was found that several options have the potential to achieve end of life fissile inventory ratio above unity, which implies potential feasibility of a self-sustainable Thorium fuel cycle in PWRs without significant reduction in the core power density. Finally, a preliminary three-dimensional coupled neutronic and thermal–hydraulic analysis for a single seed-blanket fuel assembly was performed. The results indicate that axial void distribution changes drastically with burnup. Therefore

  18. Evaluation of correlations of flow boiling heat transfer of R22 in horizontal channels.

    Science.gov (United States)

    Zhou, Zhanru; Fang, Xiande; Li, Dingkun

    2013-01-01

    The calculation of two-phase flow boiling heat transfer of R22 in channels is required in a variety of applications, such as chemical process cooling systems, refrigeration, and air conditioning. A number of correlations for flow boiling heat transfer in channels have been proposed. This work evaluates the existing correlations for flow boiling heat transfer coefficient with 1669 experimental data points of flow boiling heat transfer of R22 collected from 18 published papers. The top two correlations for R22 are those of Liu and Winterton (1991) and Fang (2013), with the mean absolute deviation of 32.7% and 32.8%, respectively. More studies should be carried out to develop better ones. Effects of channel dimension and vapor quality on heat transfer are analyzed, and the results provide valuable information for further research in the correlation of two-phase flow boiling heat transfer of R22 in channels.

  19. A fractal study for nucleate pool boiling heat transfer of nanofluids

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In this paper, a fractal model for nucleate pool boiling heat transfer of nanofluids is developed based on the fractal distribution of nanoparticles and nucleation sites on boiling surfaces. The model shows the dependences of the heat flux on nanoparticle size and the nanoparticle volume fraction of the suspension, the fractal dimension of the nanoparticle and nucleation site, temperature of nanofluids and properties of fluids. The fractal model predictions show that the natural convection stage continues relatively longer in the case of nanofluids. The addition of nanoparticles causes a decrease of the pool nucleate boiling heat transfer. The nucleate pool boiling heat transfer coefficient is decreased by increasing particle concentration. An excellent agreement between the proposed model predictions and experimental data is found. The validity of the fractal model for nucleate pool boiling heat transfer is thus verified.

  20. Experimental study on convective boiling heat transfer in narrow-gap annulus tubes

    Institute of Scientific and Technical Information of China (English)

    LI Bin; ZHAO Jian-Fu; ZHOU Fang-De; TANG Ze-Mei; HU Wen-Rui

    2004-01-01

    Since convective boiling or highly subcooled single-phase forced convection in micro-channels is an effective cooling mechanism with a wide range of applications, more experimental and theoretical studies are required to explain and verify the forced convection heat transfer phenomenon in narrow channels. In this experimental study, we model the convective boiling behavior of water with low latent heat substance Freon 113 (R-113), with the purpose of saving power consumption and visualizing experiments. Both heat transfer and pressure drop characteristics were measured in subcooled and saturated concentric narrow gap forced convection boiling. Data were obtained to qualitatively identify the effects of gap size, pressure, flow rate and wall superheat on boiling regimes and the transition between various regimes. Some significant differences from unconfined forced convection boiling were found,and also, the flow patterns in narrow vertical annulus tubes have been studied quantitatively.

  1. In-air PIXE for analyzing heavy metals in water boiled in pans

    Science.gov (United States)

    Tomita, M.; Haruyama, Y.; Saito, M.

    1993-04-01

    The release rates of heavy metals from pans were measured for boiling water as well as for an acidic solution prior to an investigation on the release or sorption of trace elements due to cooking of food by boiling. The boiled samples were condensed and analyzed by means of in-air PIXE. The release of heavy metals was measured for five kinds of pans. For all pans the release rates were considerably more increased by boiling of a 5% solution of acetic acid. Furthermore it was found that by using the alumina coated aluminum pan (alumina pan) the respective release rates of Fe, Cu and Zn were all less than 50 μg per 100 cm 2 of the pan surface dipped in the solution, and that monitoring of the contents of aluminum in the boiled solution enabled the estimation of the contribution of metal elements from the pan wall.

  2. 芒硝型卤水直接生产纯碱工艺%Process for Direct Production of Soda Ash with Glauber-Type Brine

    Institute of Scientific and Technical Information of China (English)

    彭赛军; 彭志成; 陈颖

    2011-01-01

    直接以卤水为原料,采用氨碱法或联碱法生产碳酸钠,脱氨母液采用膜法和蒸发法分离硫酸钠,脱氨母液采用蒸发法分离氯化钠、氯化铵,生产过程大幅度降低能耗和成本,直接得到氯化钠、硫酸钠、氯化铵副产品。%Sodium carbonate is directly produced using brine with ammonia–soda process or Hou's process.Sodium sulfate is separated from deaminated mother liquor by membrane process and evaporation process.Sodium chloride and sodium ammonia are separated from deaminated mother liquor.With such processes,production cost and energy consumption are greatly reduced and the by-products sodium chloride,sodium ammonia and sodium sulfate are obtained directly.

  3. West Hackberry Strategic Petroleum Reserve site brine-disposal monitoring, Year I report. Volume III. Biological oceanography. Final report

    Energy Technology Data Exchange (ETDEWEB)

    DeRouen, L.R.; Hann, R.W.; Casserly, D.M.; Giammona, C.; Lascara, V.J. (eds.)

    1983-02-01

    The Department of Energy's Strategic Petroleum Reserve Program began discharging brine into the Gulf of Mexico from its West Hackberry site near Cameron, Louisiana in May 1981. The brine originates from underground salt domes being leached with water from the Intracoastal Waterway, making available vast underground storage caverns for crude oil. The effects of brine discharge on aquatic organisms are presented in this volume. The topics covered are: benthos; nekton; phytoplankton; zooplankton; and data management.

  4. Pool boiling of nanoparticle-modified surface with interlaced wettability

    KAUST Repository

    Hsu, Chin-Chi

    2012-01-01

    This study investigated the pool boiling heat transfer under heating surfaces with various interlaced wettability. Nano-silica particles were used as the coating element to vary the interlaced wettability of the surface. The experimental results revealed that when the wettability of a surface is uniform, the critical heat flux increases with the more wettable surface; however, when the wettability of a surface is modified interlacedly, regardless of whether the modified region becomes more hydrophilic or hydrophobic, the critical heat flux is consistently higher than that of the isotropic surface. In addition, this study observed that critical heat flux was higher when the contact angle difference between the plain surface and the modified region was smaller. © 2012 Hsu et al.

  5. Interface oscillation of subcooled flow boiling in locally heated microchannels

    Science.gov (United States)

    Liu, J. T.; Peng, X. F.

    2009-02-01

    An investigation was conducted to understand flow boiling of subcooled de-ionized water in locally heated parallel microchannels. High-speed visualization technology was employed to visually observe the transient phase change process in an individual microchannel. Signal analysis method was employed in studying the interface movement and phase change process. The phase change at locally heated condition was different from those at entirely heated condition where elongated bubble(s) stayed quasi-stable for a long time without venting out. Diversified and intensive interface oscillation was observed occurring on both of the upstream and downstream bubble caps. Evaporation and condensation modes were characterized with distinguished oscillation frequencies. The film-driven oscillations of both evaporating and condensing interfaces generally operated at higher frequencies than the oscillations driven by nucleation or dropwise condensation.

  6. Nucleate pool boiling in microgravity: Recent progress and future prospects

    Science.gov (United States)

    Colin, Catherine; Kannengieser, Olivier; Bergez, Wladimir; Lebon, Michel; Sebilleau, Julien; Sagan, Michaël; Tanguy, Sébastien

    2017-01-01

    Pool boiling on flat plates in microgravity has been studied for more than 50 years. The results of recent experiments performed in sounding rocket are presented and compared to previous results. At low heat flux, the vertical oscillatory motion of the primary bubble is responsible for the increase in the heat transfer coefficient in microgravity compared to ground experiments. The effect of a non-condensable gas on the stabilisation of the large primary bubble on the heater is pointed out. Experiments on isolated bubbles are also performed on ground and in parabolic flight. The effect of a shear flow on the bubble detachment is highlighted. A force balance model allows determining an expression of the capillary force and of the drag force acting on the bubble.

  7. Investigation of vapor film motion regularities at boiling liquids

    Directory of Open Access Journals (Sweden)

    Zeigarnik Y.U.

    2013-04-01

    Full Text Available The experimental investigation of the saturated Freon-113 and distilled water film boiling on spheres with different diameters at atmospheric pressure under conditions of free convection is executed. With high-speed video average thickness and cumulative distribution function of vapor film as a function of the angle was measured. It was found that with increasing the angle the average thickness of vapor film can change by different laws depending on diameter of the sphere and the temperature difference. It was found also that the increase in the average vapor film thickness with increasing angle is more connected with the increase of large components of cumulative distribution function. It also noted the presence of quasi-periodic pulsations of the vapor film thickness in the lower part, which eventually largely determine the behavior of the interface at large angles.

  8. Laminar film boiling on inclined isothermal flat plates.

    Science.gov (United States)

    Nagendra, H. R.

    1973-01-01

    Laminar film boiling from an inclined flat plate has been investigated analytically. Using the singular perturbation scheme, the complete set of Navier-Stokes equations is solved. The zeroth-order perturbation coinciding with the boundary-layer equations for vertical flat plates governs the problem. The higher-order perturbations become important near the leading edge and for large values of the inclination angle from the vertical. The assumption of zero interfacial velocity shows that, except for fluids having large (rho x mu) ratios, the results can be predicted using the vertical flat plate results by defining a modified Grashof parameter containing a cos phi term. When the interfacial shear is considered, the solutions indicate that for fluids having large (rho x mu) ratios, the heat transfer rates will be larger (approximately 15% maximum) than those predicted by the simplified model using zero interfacial velocity. In general, the inclination decreases the rate of heat transfer as well as the rate of evaporation.

  9. Theoretical prediction method of subcooled flow boiling CHF

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Young Min; Chang, Soon Heung [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1998-12-31

    A theoretical critical heat flux (CHF ) model, based on lateral bubble coalescence on the heated wall, is proposed to predict the subcooled flow boiling CHF in a uniformly heated vertical tube. The model is based on the concept that a single layer of bubbles contacted to the heated wall prevents a bulk liquid from reaching the wall at near CHF condition. Comparisons between the model predictions and experimental data result in satisfactory agreement within less than 9.73% root-mean-square error by the appropriate choice of the critical void fraction in the bubbly layer. The present model shows comparable performance with the CHF look-up table of Groeneveld et al.. 28 refs., 11 figs., 1 tab. (Author)

  10. Boiling visualization on vertical fins with tunnel-pore structures

    Directory of Open Access Journals (Sweden)

    Kaniowski Robert

    2012-04-01

    Full Text Available The paper presents experimental studies of nucleate boiling heat transfer from a system of connected horizontal and vertical subsurface tunnels. The experiments were carried out for water at atmospheric pressure. The tunnel external covers were manufactured out of perforated copper foil (holes diameter 0.3 mm, sintered with the mini-fins, formed on the vertical side of the 10 mm high rectangular fins and horizontal inter-fin surface. The image acquisition speed was 493 fps (at resolution 400 × 300 pixels with Photonfocus PHOT MV-D1024-160-CL camera. Visualization investigations aimed to identify nucleation sites and flow patterns and to determine the bubble departure diameter and frequency at various superheats for vertical tunnels. At low superheat vapor bubbles are generated nearly exclusively by the vertical tunnel. At medium values of superheat, pores of the horizontal tunnel activate.

  11. Flow boiling of water on nanocoated surfaces in a microchannel

    CERN Document Server

    Phan, Hai Trieu; Marty, Philippe; Colasson, Stéphane; Gavillet, Jérôme

    2010-01-01

    Experiments were performed to study the effects of surface wettability on flow boiling of water at atmospheric pressure. The test channel is a single rectangular channel 0.5 mm high, 5 mm wide and 180 mm long. The mass flux was set at 100 kg/m2 s and the base heat flux varied from 30 to 80 kW/m2. Water enters the test channel under subcooled conditions. The samples are silicone oxide (SiOx), titanium (Ti), diamond-like carbon (DLC) and carbon-doped silicon oxide (SiOC) surfaces with static contact angles of 26{\\deg}, 49{\\deg}, 63{\\deg} and 103{\\deg}, respectively. The results show significant impacts of surface wettability on heat transfer coefficient.

  12. Flow Structures Around Micro-bubbles During Subcooled Nucleate Boiling

    Institute of Scientific and Technical Information of China (English)

    WANG Hao; PENG Xiao-Feng; David M. Christopher; WANG Bu-Xuan

    2005-01-01

    The flow structures were investigated around micro bubbles on extremely thin wires during subcooled nucleate boiling. Jet flows emanating from the bubbles were observed visually with the fluid field measurement using high-speed photography and a PIV system. The jet flows induced a strong pumping effect around a bubble. The multi-jet structure was further observed experimentally, indicating the evolution of flow structure around micro bubbles. Numerical simulations explore that the jet flows were induced by a strong Marangoni effect due to high temperature gradients near the wire. The bubble interface with multi-jet structure has abnormal temperature distribution such that the coolest parts were observed at two sides of a bubble extending into the subcooled bulk liquid rather than at the top. Evaporation and condensation on the bubble interface play important roles not only in controlling the intensity of the jet flow, but also in bringing out the multi-jet structure.

  13. Computation of boiling water on circular finned tubes

    Energy Technology Data Exchange (ETDEWEB)

    Fan, C.C.; Liaw, S.P. [National Taiwan Ocean Univ., Keelung (Taiwan, Province of China). Dept. of Mechanical and Marine Engineering

    1999-04-01

    This study investigates the maximum heat transfer rate and the critical temperature of circular finned tubes in a boiling liquid. The analysis is conducted numerically by solving a two-dimensional heat conduction equation in a steady state. The dependence between heat flux and the temperature at the inner wall of the tube is quantified. Varying the width, height, and pitch of fins, an optimal finned tube with efficient heat transfer rate can be obtained. In the theoretical approach the successive over relaxation (S.O.R.) accompanied with Multi-grid scheme is used. The local heat transfer rates are assumed to follow power-law-type temperature dependence. The initial guess at very high temperatures or so-called a cooling process is also executed in a same way. The results reveal that increasing either the width or the height of a fin increases the total heat transfer rate.

  14. Aerobic methanotrophic communities at the Red Sea brine-seawater interface

    Directory of Open Access Journals (Sweden)

    Rehab Z. Abdallah

    2014-09-01

    Full Text Available The central rift of the Red Sea contains 25 brine pools with different physicochemical conditions, dictating the diversity and abundance of the microbial community. Three of these pools, the Atlantis II, Kebrit and Discovery Deeps, are uniquely characterized by a high concentration of hydrocarbons. The brine-seawater interface, described as an anoxic-oxic (brine-seawater boundary, is characterized by a high methane concentration, thus favoring aerobic methane oxidation. The current study analyzed the aerobic free–living methane-oxidizing bacterial communities that potentially contribute to methane oxidation at the brine-seawater interfaces of the three aforementioned brine pools, using metagenomic pyrosequencing, 16S rRNA pyrotags and pmoA library constructs. The sequencing of 16S rRNA pyrotags revealed that these interfaces are characterized by high microbial community diversity. Signatures of aerobic methane-oxidizing bacteria were detected in the Atlantis II Interface (ATII-I and the Kebrit Deep Upper (KB-U and Lower (KB-L brine-seawater interfaces. Through phylogenetic analysis of pmoA, we further demonstrated that the ATII-I aerobic methanotroph community is highly diverse. We propose four ATII-I pmoA clusters. Most importantly, cluster 2 groups with marine methane seep methanotrophs, and cluster 4 represent a unique lineage of an uncultured bacterium with divergent alkane monooxygenases. Moreover, non-metric multidimensional scaling (NMDS based on the ordination of putative enzymes involved in methane metabolism showed that the Kebrit interface layers were distinct from the ATII-I and DD-I brine-seawater interfaces.

  15. Using fluorescence to characterize dissolved organic matter in Antarctic sea ice brines

    Science.gov (United States)

    Stedmon, Colin A.; Thomas, David N.; Papadimitriou, Stathys; Granskog, Mats A.; Dieckmann, Gerhard S.

    2011-09-01

    Sea ice plays a dynamic role in the air-sea exchange of CO2. In addition to abiotic inorganic carbon fluxes, an active microbial community produces and remineralizes organic carbon, which can accumulate in sea ice brines as dissolved organic matter (DOM). In this study, the characteristics of DOM fluorescence in Antarctic sea ice brines from the western Weddell Sea were investigated. Two humic-like components were identified, which were identical to those previously found to accumulate in the deep ocean and represent refractory material. Three amino-acid-like signals were found, one of which was unique to the brines and another that was spectrally very similar to tryptophan and found both in seawater and in brine samples. The tryptophan-like fluorescence in the brines exhibited intensities higher than could be explained by conservative behavior during the freezing of seawater. Its fluorescence was correlated with the accumulation of nitrogen-rich DOM to concentrations up to 900 μmol L-1 as dissolved organic carbon (DOC) and, thus, potentially represented proteins released by ice organisms. A second, nitrogen-poor DOM fraction also accumulated in the brines to concentrations up to 200 μmol L-1 but was not correlated with any of the fluorescence signals identified. Because of the high C:N ratio and lack of fluorescence, this material is thought to represent extracellular polymeric substances, which consist primarily of polysaccharides. The clear grouping of the DOM pool into either proteinaceous or carbohydrate-dominated material indicates that the production and accumulation of these two subpools of DOM in sea ice brines is, to some extent, decoupled.

  16. Modeling brine and nutrient dynamics in Antarctic sea ice: the case of dissolved silica

    Science.gov (United States)

    Vancoppenolle, M.; Goosse, H.; de Montety, A.; Fichefet, T.; Tremblay, B.; Tison, J.

    2009-12-01

    Sea ice ecosystems are characterized by micro-algae living in brine inclusions. The growth rate of ice algae depends on light and nutrient supply. Here, the interactions between nutrients and brine dynamics under the influence of algae are investigated using a one-dimensional model. The model includes snow and ice thermodynamics with brine physics and an idealized sea ice biological component, characterized by one nutrient, namely dissolved silica (DSi). In the model, DSi follows brine motion and is consumed by ice algae. Depending on physical ice characteristics, the brine flow is either advective, diffusive or turbulent. The vertical profiles of ice salinity and DSi concentration are solutions of advection-diffusion equations. The model is configured to simulate the typical thermodynamic regimes of first-year Antarctic pack ice. The simulated vertical profiles of salinity and DSi qualitatively reproduce observations. Analysis of results highlights the role of convection in the lowermost 5-10 cm of ice. Convection mixes saline, nutrient-poor brine with comparatively fresh, nutrient-rich seawater. This implies a rejection of salt to the ocean and a flux of DSi to the ice. In presence of growing algae, the simulated ocean-to-ice DSi flux increases by 0-115% compared to an abiotic situation. In turn, primary production and brine convection act in synergy to form a nutrient pump. The other important processes are the flooding of the surface by seawater and the percolation of meltwater. The former refills nutrients near the ice surface in spring. The latter, if present, tends to expell nutrients from the ice in summer. Sketch of salt (left) and nutrient (right) exchanges at the ice-ocean interface proposed in this paper.

  17. Effects of brine migration on waste storage systems. Final report. [Thermomechanical effects

    Energy Technology Data Exchange (ETDEWEB)

    Gaffney, E.S.; Nickell, R.E.

    1979-05-15

    Processes which can lead to mobilization of brine adjacent to spent fuel or nuclear waste canisters and some of the thermomechanical consequences have been investigated. Velocities as high as 4 x 10/sup -7/ m s/sup -1/ (13 m y/sup -1/) are calculated at the salt/canister boundary. As much as 40 liters of pure NaCl brine could accumulate around each canister during a 10-year storage period. Accumulations of bittern brines would probably be less, in the range of 2 to 5 liters. With 0.5% water, NaCl brine accumulation over a 10-year storage cycle around a spent fuel canister producing 0.6 kW of heat is expected to be less than 1 liter for centimeter-size inclusions and less than 0.5 liter for millimeter-size inclusions. For bittern brines, about 25 years would be required to accumulate 0.4 liter. The most serious mechanical consequence of brine migration would be the increased mobility of the waste canister due to pressure solution. In pressure solution enhanced deformation, the existence of a thin film of fluid either between grains or between media (such as between a canister and the salt) provides a pathway by which the salt can be redistributed leading to a marked increase in strain rates in wet rock relative to dry rock. In salt, intergranular water will probably form discontinuous layers rather than films so that they would dominate pressure solution. A mathematical model of pressure solution indicates that pressure solution will not lead to appreciable canister motions except possibly in fine grained rocks (less than 10/sup -4/ m). In fine grained salts, details of the contact surface between the canister and the salt bed may lead to large pressure solution motions. A numerical model indicates that heat transfer in the brine layer surrounding a spent fuel canister is not conduction dominated but has a significant convective component.

  18. Nucleate boiling pressure drop in an annulus: Book 2

    Energy Technology Data Exchange (ETDEWEB)

    Block, J.A.; Crowley, C.; Dolan, F.X.; Sam, R.G.; Stoedefalke, B.H.

    1992-11-01

    The application of the work described in this report is the production reactors at the Savannah River Site, and the context is nuclear reactor safety. The Loss of Coolant Accident (LOCA) scenario considered involves a double-ended break of a primary coolant pipe in the reactor. During a LOCA, the flow through portions of the reactor may reverse direction or be greatly reduced, depending upon the location of the break. The reduced flow rate of coolant (D{sub 2}O) through the fuel assembly channels of the reactor -- downflow in this situation -- can lead to boiling and to the potential for flow instabilities which may cause some of the fuel assembly channels to overheat and melt. That situation is to be avoided. The experimental approach is to provide a test annulus which simulates geometry, materials, and flow conditions in a Mark-22 fuel assembly (Coolant Channel 3) to the extent possible. The annulus has a full-scale geometry, and in fat uses SRL dummy hardware for the inner annulus wall in the ribbed geometry. The materials aluminum. The annulus is uniformly heated in the axial direction, but the circumferential heat flux can be varied to provide ``power tilt`` or asymmetric heating of the inner and outer annulus walls. The test facility uses H{sub 2}O rather than D{sub 2}O, but it includes the effects of dissolved helium gas present in the reactor. The key analysis approaches are: To compare the minima in the measured demand curves with analytical criteria, in particular the Saha-Zuber (1974) model; and to compare the pressure and temperature as a function of length in the annulus with an integral model for flow boiling in a heated channel. Nineteen test series and a total of 178 tests were performed. Testing addressed the effects of: Heat flux; pressure; helium gas; power tilt; ribs; asymmetric heat flux.

  19. Nucleate boiling pressure drop in an annulus: Book 3

    Energy Technology Data Exchange (ETDEWEB)

    Block, J.A.; Crowley, C.; Dolan, F.X.; Sam, R.G.; Stoedefalke, B.H.

    1992-11-01

    The application of the work described in this report is the production reactors at the Savannah River Site, and the context is nuclear reactor safety. The Loss of Coolant Accident (LOCA) scenario considered involves a double-ended break of a primary coolant pipe in the reactor. During a LOCA, the flow through portions of the reactor may reverse direction or be greatly reduced, depending upon the location of the break. The reduced flow rate of coolant (D{sub 2}O) through the fuel assembly channels of the reactor -- downflow in this situation -- can lead to boiling and to the potential for flow instabilities which may cause some of the fuel assembly channels to overheat and melt. That situation is to be avoided. The experimental approach is to provide a test annulus which simulates geometry, materials, and flow conditions in a Mark-22 fuel assembly (Coolant Channel 3) to the extent possible. The annulus has a full-scale geometry, and in fat uses SRL dummy hardware for the inner annulus wall in the ribbed geometry. The materials aluminum. The annulus is uniformly heated in the axial direction, but the circumferential heat flux can be varied to provide ``power tilt`` or asymmetric heating of the inner and outer annulus walls. The test facility uses H{sub 2}O rather than D{sub 2}O, but it includes the effects of dissolved helium gas present in the reactor. The key analysis approaches are: To compare the minima in the measured demand curves with analytical criteria, in particular the Saha-Zuber (1974) model; and to compare the pressure and temperature as a function of length in the annulus with an integral model for flow boiling in a heated channel. This document consists of data plots and summary files of temperature measurements.

  20. Nucleate boiling pressure drop in an annulus: Book 4

    Energy Technology Data Exchange (ETDEWEB)

    Block, J.A.; Crowley, C.; Dolan, F.X.; Sam, R.G.; Stoedefalke, B.H.

    1992-11-01

    The application of the work described in this report is the production reactors at the Savannah River Site, and the context is nuclear reactor safety. The Loss of Coolant Accident (LOCA) scenario considered involves a double-ended break of a primary coolant pipe in the reactor. During a LOCA, the flow through portions of the reactor may reverse direction or be greatly reduced, depending upon the location of the break. The reduced flow rate of coolant (D{sub 2}O) through the fuel assembly channels of the reactor -- downflow in this situation -- can lead to boiling and to the potential for flow instabilities which may cause some of the fuel assembly channels to overheat and melt. That situation is to be avoided. The experimental approach is to provide a test annulus which simulates geometry, materials, and flow conditions in a Mark-22 fuel assembly (Coolant Channel 3) to the extent possible. The annulus has a full-scale geometry, and in fat uses SRL dummy hardware for the inner annulus wall in the ribbed geometry. The materials aluminum. The annulus is uniformly heated in the axial direction, but the circumferential heat flux can be varied to provide ``power tilt`` or asymmetric heating of the inner and outer annulus walls. The test facility uses H{sub 2}O rather than D{sub 2}O, but it includes the effects of dissolved helium gas present in the reactor. The key analysis approaches are: To compare the minima in the measured demand curves with analytical criteria, in particular the Saha-Zuber (1974) model; and to compare the pressure and temperature as a function of length in the annulus with an integral model for flow boiling in a heated channel. This document consists of data plots and summary files of temperature measurements.

  1. Bacterial virulence analysis using brine shrimp as an infection model in relation to the importance of quorum sensing and proteases.

    Science.gov (United States)

    Lee, Mi-Nan; Kim, Soo-Kyoung; Li, Xi-Hui; Lee, Joon-Hee

    2014-01-01

    Brine shrimp are aquatic crustaceans belonging to a genus of Artemia. This organism is widely used for testing the toxicity of chemicals. In this study, brine shrimp were evaluated as an infection model organism to study bacterial virulence. Artemia nauplii were infected with various pathogenic bacteria, such as Vibrio vulnificus, Pseudomonas aeruginosa, Burkholderia vietnamiensis, Staphylococcus aureus, and Escherichia coli, and the susceptibility to these bacteria was investigated by counting the survival of the infected nauplii. While all of the tested bacteria have significant virulence to brine shrimp, killing the nauplii in a few days, V. vulnificus showed the strongest virulence. P. aeruginosa also showed a dose-dependent virulence to brine shrimp, but the virulence was weaker than that of V. vulnificus. The virulence tests using the virulence-attenuated mutants of V. vulnificus and P. aeruginosa, such as quorum sensing (QS) mutants or protease-deficient mutants showed a significant attenuation of virulence, demonstrating that the QS mechanism is important in the virulence of these bacteria to brine shrimp. B. vietnamiensis, S. aureus, and E. coli were also virulent to brine shrimp and the virulence was correlated with dosage within 24 h under our conditions. Salmonella enterica Typhimurium and Bacillus subtilis were also virulent to brine shrimp, but the virulence was weak and slowly exerted compared with that of other bacteria. Taken together, we suggest that brine shrimp are a good infection model to assay bacterial virulence, especially for V. vulnificus and P. aeruginosa, and QS is important in the bacterial virulence to brine shrimp.

  2. Mathematical and experimental modeling of nucleate boiling heat transfer in liquid nitrogen

    Science.gov (United States)

    Fusco, Ciro

    The investigation of nucleate boiling heat transfer, because of its complexity, is usually carried out experimentally and by using phenomenological approximations. The purpose of this work is to capture the essential features of nucleate boiling heat transfer in liquid nitrogen and to formulate a theoretical description useful for the prediction of the temperature fluctuations and beat flux. Experimental analysis was coupled with mathematical modeling to elucidate nucleate boiling heat transfer. The experimental setting consists of a platinum wire immersed in liquid nitrogen. A current is passed through the wire while the resistance is measured. The orientation of the wire can be changed from horizontal to vertical. The fluctuations of the wire temperature are measured. Using high-speed analysis, we characterized nucleate boiling heat transfer from the wire as occurring in two distinct phases or regimes: discrete nucleate boiling and transition boiling. We defined discrete nucleate boiling as the phase during which the active nucleation sites are clearly distinguishable from one another with no bubble coalescence occurring between adjacent sites. The high-speed analysis helped also to compute the frequencies, diameters, and nucleation density of departing bubbles as well as the energy loss by a single bubble during the discrete nucleate boiling regime. These parameters were subsequently used to formulate a mathematical model to simulate by discrete time steps the discrete nucleate boiling heat transfer from the platinum wire. The average temperature of the wire can be adequately modeled with only one variable, the power input. In addition to predicting the average temperature of the wire in the discrete nucleate boiling regime the model predicts well the average temperature of the wire in the conduction and convection regime and the transition regime. The model also reproduces the fluctuation of temperature in the discrete nucleate boiling regime. The mathematical

  3. Oxomemazine hydro­chloride

    OpenAIRE

    Siddegowda, M. S.; Butcher, Ray J.; Mehmet Akkurt; Yathirajan, H.S.; Ramesh, A. R.

    2011-01-01

    In the title compound [systematic name: 3-(5,5-dioxophenothiazin-10-yl)-N,N,2-trimethylpropanaminium chloride], C18H23N2O2S+·Cl−, the dihedral angle between the two outer aromatic rings of the phenothiazine unit is 30.5 (2)°. In the crystal, the components are linked by N—H...Cl and C—H...Cl hydrogen bonds and C—H...π interactions.

  4. Shock compression of polyvinyl chloride

    Science.gov (United States)

    Neogi, Anupam; Mitra, Nilanjan

    2016-04-01

    This study presents shock compression simulation of atactic polyvinyl chloride (PVC) using ab-initio and classical molecular dynamics. The manuscript also identifies the limits of applicability of classical molecular dynamics based shock compression simulation for PVC. The mechanism of bond dissociation under shock loading and its progression is demonstrated in this manuscript using the density functional theory based molecular dynamics simulations. The rate of dissociation of different bonds at different shock velocities is also presented in this manuscript.

  5. Developing chloride resisting concrete using PFA

    Energy Technology Data Exchange (ETDEWEB)

    Dhir, R.K.; El-Mohr, M.A.K.; Dyer, T.D. [Univ. of Dundee (United Kingdom). Dept. of Civil Engineering

    1997-11-01

    PFA concrete mixes were designed to optimize resistance to chloride ingress. Chloride binding capacity, intrinsic permeability and their concomitant influence on the coefficient of chloride diffusion have been investigated. PFA replacements up to 67% and exposure concentrations of 0.1, 0.5, 1.0 and 5.0 mole/liter were used. Chloride binding capacity was found to increase with increasing PFA replacement up to 50% and to then decline. It increased with chloride exposure concentration as well as water/binder ratio. The coefficient of chloride diffusion of concrete samples was found to be dependent on both the intrinsic permeability of the concrete and the ability of its cement matrix to bind chlorides.

  6. Salt, chloride, bleach, and innate host defense.

    Science.gov (United States)

    Wang, Guoshun; Nauseef, William M

    2015-08-01

    Salt provides 2 life-essential elements: sodium and chlorine. Chloride, the ionic form of chlorine, derived exclusively from dietary absorption and constituting the most abundant anion in the human body, plays critical roles in many vital physiologic functions, from fluid retention and secretion to osmotic maintenance and pH balance. However, an often overlooked role of chloride is its function in innate host defense against infection. Chloride serves as a substrate for the generation of the potent microbicide chlorine bleach by stimulated neutrophils and also contributes to regulation of ionic homeostasis for optimal antimicrobial activity within phagosomes. An inadequate supply of chloride to phagocytes and their phagosomes, such as in CF disease and other chloride channel disorders, severely compromises host defense against infection. We provide an overview of the roles that chloride plays in normal innate immunity, highlighting specific links between defective chloride channel function and failures in host defense.

  7. The brine shrimp artemia: adapted to critical life conditions.

    Science.gov (United States)

    Gajardo, Gonzalo M; Beardmore, John A

    2012-01-01

    The brine shrimp Artemia is a micro-crustacean, well adapted to the harsh conditions that severely hypersaline environments impose on survival and reproduction. Adaptation to these conditions has taken place at different functional levels or domains, from the individual (molecular-cellular-physiological) to the population level. Such conditions are experienced by very few equivalent macro-planktonic organisms; thus, Artemia can be considered a model animal extremophile offering a unique suite of adaptations that are the focus of this review. The most obvious is a highly efficient osmoregulation system to withstand up to 10 times the salt concentration of ordinary seawater. Under extremely critical environmental conditions, for example when seasonal lakes dry-out, Artemia takes refuge by producing a highly resistant encysted gastrula embryo (cyst) capable of severe dehydration enabling an escape from population extinction. Cysts can be viewed as gene banks that store a genetic memory of historical population conditions. Their occurrence is due to the evolved ability of females to "perceive" forthcoming unstable environmental conditions expressed by their ability to switch reproductive mode, producing either cysts (oviparity) when environmental conditions become deleterious or free-swimming nauplii (ovoviviparity) that are able to maintain the population under suitable conditions. At the population level the trend is for conspecific populations to be fragmented into locally adapted populations, whereas species are restricted to salty lakes in particular regions (regional endemism). The Artemia model depicts adaptation as a complex response to critical life conditions, integrating and refining past and present experiences at all levels of organization. Although we consider an invertebrate restricted to a unique environment, the processes to be discussed are of general biological interest. Finally, we highlight the benefits of understanding the stress response of

  8. The brine shrimp Artemia: adapted to critical life conditions

    Directory of Open Access Journals (Sweden)

    Gonzalo M Gajardo

    2012-06-01

    Full Text Available The brine shrimp Artemia is a micro-crustacean, well adapted to the harsh conditions that severely hypersaline environments impose on survival and reproduction. Adaptation to these conditions has taken place at different functional levels or domains, from the individual (molecular-cellular-physiological to the population level. Such conditions are experienced by very few equivalent macro-planktonic organisms; thus, Artemia can be considered a model animal extremophile offering a unique suite of adaptations that are the focus of this review. The most obvious is a highly efficient osmoregulation system to withstand up to 10 times the salt concentration of ordinary seawater. Under extremely critical environmental conditions, for example when seasonal lakes dry out, Artemia takes refuge by producing a highly resistant encysted gastrula embryo (cyst capable of severe dehydration enabling an escape from population extinction. Cysts can be viewed as gene banks that store a genetic memory of historical population conditions. Their occurrence is due to the evolved ability of females to perceive forthcoming unstable environmental conditions expressed by their ability to switch reproductive mode, producing either cysts (oviparity when environmental conditions become deleterious or free-swimming nauplii (ovoviviparity that are able to maintain the population under suitable conditions.At the population level the trend is for conspecific populations to be fragmented into locally adapted populations, whereas species are restricted to salty lakes in particular regions (regional endemism. The Artemia model depicts adaptation as a complex response to critical life conditions, integrating and refining past and present experiences at all levels of organization. Although we consider an invertebrate restricted to a unique environment, the processes to be discussed are of general biological interest. Finally, we highlight the benefits of understanding the stress

  9. Heat Transfer in Film Boiling from Electrically Heated Nichrome Wire to Boiling Water at Different Pressure-II

    Directory of Open Access Journals (Sweden)

    Devi Dayal

    1969-01-01

    Full Text Available Values of film thickness in film boiling have been computed for three different sizes of nichrome wires at five different sub-atmospheric pressures. The values of alpha , total heat transmission co-efficient, ac heat transmission co-efficient due to conduction through the vapour film and alpha R, heat transmission co-efficient due to radiation, have been calculated. The values of film thickness were found to decrease with external pressure, but were found to increase slightly with the radius of the wire. alpha & alpha c both increase with rise of pressure but decrease with the radius of the radius of the heated wire. Alpha R shows a minimum value at a pressure of 15 cm. of Hg. in the case of all the wire sizes. The radiation loss alpha R is much smaller than conduction loss alpha. "

  10. Experimental Work Conducted on MgO Inundated Hydration in WIPP-Relevant Brines

    Science.gov (United States)

    Deng, H.; Xiong, Y.; Nemer, M. B.; Johnsen, S.

    2009-12-01

    Magnesium oxide (MgO) is being emplaced in the Waste Isolation Pilot Plant (WIPP) as an engineered barrier to mitigate the effect of microbial CO2 generation on actinide mobility in a postclosure repository environment. MgO will sequester CO2 and consume water in brine or water vapor in the gaseous phase. Martin Marietta (MM) MgO is currently being emplaced in the WIPP. A fractional-factorial experiment has been performed to study the inundated-hydration of MM MgO as a function of its particle size, solid-to-liquid ratio, and brine type. MgO hydration experiments have been carried out with three MgO particle sizes and two solid-to-liquid ratios in three WIPP-related brines: ERDA-6, GWB and simplified GWB. ERDA-6 is a synthetic NaCl-rich brine typical of a Castile brine reservoir below the repository. GWB is a synthetic MgCl2- and NaCl-rich brine representative of intergranular brines from the Salado Formation at or near the stratigraphic horizon of the repository. Simplified GWB contains amounts of Mg, Na, and Cl similar to those in GWB without other minor constituents. The hydration products include brucite (Mg(OH)2) and phase 5 (Mg3(OH)5Cl4H2O). In addition to phase 5, MgO hydration in GWB or simplified GWB produces brucite, whereas MgO hydrated in ERDA-6 only produces brucite. The MgO particle size has had a significant effect on the formation of hydration products: small MgO particles have hydrated before the large particles. MgO has hydrated faster in simplified GWB than in the other two brines. In ERDA-6, the solid-to-liquid ratio has affected the brine pH due to the presence of CaO (~1 wt %) as an impurity in MM MgO. GWB has sufficient dissolved Mg to buffer pH despite small amounts of CaO. Both our results and thermodynamic modeling indicate that phase-5 is the stable Mg-OH-Cl phase in Mg-Na-Cl-dominated brines with ionic strengths and chemical compositions similar to that of GWB. In contrast, phase-3 (Mg2(OH)3Cl4H2O) is the stable phase in the MgCl2

  11. Distinctive Microbial Community Structure in Highly Stratified Deep-Sea Brine Water Columns

    KAUST Repository

    Bougouffa, Salim

    2013-03-29

    Atlantis II and Discovery are two hydrothermal and hypersaline deep-sea pools in the Red Sea rift that are characterized by strong thermohalo-stratification and temperatures steadily peaking near the bottom. We conducted comprehensive vertical profiling of the microbial populations in both pools and highlighted the influential environmental factors. Pyrosequencing of the 16S rRNA genes revealed shifts in community structures vis-à-vis depth. High diversity and low abundance were features of the deepest convective layers despite the low cell density. Surprisingly, the brine interfaces had significantly higher cell counts than the overlying deep-sea water, yet they were lowest in diversity. Vertical stratification of the bacterial populations was apparent as we moved from the Alphaproteobacteria-dominated deep sea to the Planctomycetaceae- or Deferribacteres-dominated interfaces to the Gammaproteobacteria-dominated brine layers. Archaeal marine group I was dominant in the deep-sea water and interfaces, while several euryarchaeotic groups increased in the brine. Across sites, microbial phylotypes and abundances varied substantially in the brine interface of Discovery compared with Atlantis II, despite the near-identical populations in the overlying deep-sea waters. The lowest convective layers harbored interestingly similar microbial communities, even though temperature and heavy metal concentrations were very different. Multivariate analysis indicated that temperature and salinity were the major influences shaping the communities. The harsh conditions and the low-abundance phylotypes could explain the observed correlation in the brine pools.

  12. Environmental safety of underground injection of oil field brines in Louisiana

    Energy Technology Data Exchange (ETDEWEB)

    Conger, R.M.

    1986-09-01

    Louisiana contains almost 4000 brine injection wells that dispose an estimated 1 billion bbl of brine each year, making underground injection that state's most widely practiced method of oil field brine disposal. Louisiana has had no known contamination of a public water supply from underground brine injection; however, the magnitude of this activity presents a potential for contamination if proper disposal practices are not followed. Following the earliest discovery of oil, the petroleum industry has been improving methods to protect ground-water aquifers from underground injection. Although economic incentives spurred the earliest use of underground injection, the technology has progressed to become a method providing environmental safety to ground-water aquifers. Complex reservoir modeling, developed for use in secondary and enhanced recovery techniques, has been applied to simulate pressure effects and vertical migration potential for underground injection reservoirs. Conventional well designs that allow monitoring of well conditions have replaced older, unreliable designs. Improvements in wireline logging make it possible to test the isolation of injected brines from vertical movement along the well bore.

  13. Meltability and Stretchability of White Brined Cheese: Effect of Emulsifier Salts

    Directory of Open Access Journals (Sweden)

    Khaled Abu-Alruz

    2009-01-01

    Full Text Available Problem statement: This study was based on the hypothesis that by adding low concentrations of emulsifier salts, may specifically act on the cross linking bonds of the protein matrix, to the original brine (storage medium it would be possible to induce meltability and stretchability in white brined cheese. Approach: A new apparatus for measuring the actual stretchability was designed and constructed; measurements on different cheese samples proved its validity and reliability to measure stretchability. The apparatus was used to evaluate the effect of five types of emulsifier salts under different processing conditions. Results: It was found that by adding 0.2% (w/w Puromelt C1 or Monosodium phosphate to the brine of white brined cheese, higher levels of stretchability and meltability were induced after 2-4 weeks of storage. Conclusion: Addition of emulsifying salts was proved to be effective method in inducing meltability and stretchability of white brined cheese. Type of salt, its concentration, type of cheese and soaking time are factors that should be controlled to attain the optimum results.

  14. Experimental investigation on partial pool boiling heat transfer in pure liquids

    Directory of Open Access Journals (Sweden)

    Fazel Seyed Ali Alavi

    2016-01-01

    Full Text Available Saturated partial pool boiling heat transfer has been experimentally investigated on a horizontal rod heater. The boiling liquids are including water and ethanol. The heating section is made by various materials including SS316, copper, aluminum and brass. Experiments have been performed at several degrees of surface roughness ranging between 30 and 360 micrometer average vertical deviation. The measurements are including boiling heat transfer coefficient, bubble departing diameter and frequency and also nucleation site density. The data have been compared to major existing correlations. It is shown that experimental data do not match with major correlations at the entire range of experiments with acceptable accuracy. In this article, the boiling heat transfer area has been divided in two complementary areas, the induced forced convection area and the boiling affected area. Based on two dimensionless groups, including Eötvös and Roshko numbers, a semi-empirical model have been proposed to predict the boiling heat transfer coefficient. It is shown that the proposed model provides improved performance in prediction of the boiling heat transfer coefficient in comparison with to existing correlations.

  15. Potent odorants characterize the aroma quality of leaves and stalks in raw and boiled celery.

    Science.gov (United States)

    Kurobayashi, Yoshiko; Kouno, Emi; Fujita, Akira; Morimitsu, Yasujiro; Kubota, Kikue

    2006-04-01

    The raw and boiled odors of celery leaves and stalks were investigated. Among 12 compounds identified as potent odorants, 3-n-butylphthalide 1, sedanenolide 2, and trans- and cis-sedanolides 3, 4 were assessed to be most contributive to the overall odor of celery. These three phthalides, (3E,5Z)-1,3,5-undecatriene, myrcene, and (E)-2-nonenal were common to both raw and boiled materials. Two compounds, ((Z)-3-hexenal and (Z)-3-hexenol), were dominant in raw materials and four compounds, (2-methylbutanoic acid, sotolon, beta-damascenone, and beta-ionone), were dominant in boiled materials. Sensory evaluations were performed on natural celery odor and a series of reconstructed model aromas by assigning each intensity ratings for a set of seven odor qualities which aptly describe the odors of raw and boiled celery. According to the evaluation results, six common components contributed to the moderate odor of raw celery, two components dominant in raw materials enhanced the raw celery character, and four components dominant in boiled materials reduced the raw celery character and enhanced the boiled celery character. It was clarified that boiling-induced changes in celery odor were not affected by the amounts of phthalides, but by thermally generated compounds such as sotolon, beta-damascenone, and beta-ionone, which reduce the "green spicy" note.

  16. Hypergravity to Explore the Role of Buoyancy in Boiling in Porous Media

    Science.gov (United States)

    Lioumbas, John S.; Krause, Jutta; Karapantsios, Thodoris D.

    2013-02-01

    Boiling in porous media is an active topic of research since it is associated with various applications, e.g. microelectronics cooling, wetted porous media as thermal barriers, food frying. Theoretical expressions customary scale boiling heat and mass transfer rates with the value of gravitational acceleration. Information obtained at low gravity conditions show a deviation from the above scaling law but refers exclusively to non-porous substrates. In addition, the role of buoyancy in boiling at varying gravitational levels (i.e. from microgravity—important to satellites and future Lunar and Martial missions, to high-g body forces—associated with fast aerial maneuvers) is still unknown since most experiments were conducted over a limited range of g-value. The present work aims at providing evidence regarding boiling in porous media over a broad range of hypergravity values. For this, a special device has been constructed for studying boiling inside porous media in the Large Diameter Centrifuge (LDC at ESA/ESTEC). LDC offers the unique opportunity to cancel the shear stresses and study only the effect of increased normal forces on boiling in porous media. The device permits measurement of the temperature field beneath the surface of the porous material and video recordings of bubble activity over the free surface of the porous material. The preliminary results presented from experiments conducted at terrestrial and hypergravity conditions, reveal for the first time the influence of increased levels of gravity on boiling in porous media.

  17. Bubble spreading during the boiling crisis: modelling and experimenting in microgravity

    Science.gov (United States)

    Nikolayev, V.; Beysens, D.; Garrabos, Y.; Lecoutre, C.; Chatain, D.

    2006-09-01

    Boiling is a very efficient way to transfer heat from a heater to the liquid carrier. We discuss the boiling crisis, a transition between two regimes of boiling: nucleate and film boiling. The boiling crisis results in a sharp decrease in the heat transfer rate, which can cause a major accident in industrial heat exchangers. In this communication, we present a physical model of the boiling crisis based on the vapor recoil effect. Under the action of the vapor recoil the gas bubbles begin to spread over the heater thus forming a germ for the vapor film. The vapor recoil force not only causes its spreading, it also creates a strong adhesion to the heater that prevents the bubble departure, thus favoring the further spreading. Near the liquid-gas critical point, the bubble growth is very slow and allows the kinetics of the bubble spreading to be observed. Since the surface tension is very small in this regime, only microgravity conditions can preserve a convex bubble shape. In the experiments both in the Mir space station and in the magnetic levitation facility, we directly observed an increase of the apparent contact angle and spreading of the dry spot under the bubble. Numerical simulations of the thermally controlled bubble growth show this vapor recoil effect too thus confirming our model of the boiling crisis.

  18. Hydrolysis of cupric chloride in aqueous ammoniacal ammonium chloride solutions

    Directory of Open Access Journals (Sweden)

    Limpo, J. L.

    1995-06-01

    Full Text Available Cupric solubility in the CuCl2-NH4Cl-NH3-H2O system for chloride concentrations lower than 4 molal in the temperature range 25-60 °C was studied. The experimental results show that for chloride concentration between 3.0 and 1.0 molal the cupric solubility is determined by the solubility of the cupric hydroxychloride Cu(OH1.5Cl0.5. For a chloride concentration value of 4.0 molal, there are two cupric compounds, the hydroxychloride Cu(OH1.5Cl0.5 or the diammine chloride Cu(NH32Cl2, on which the solubility of Cu(II depends, according to the temperature and the value of the ratio [NH3]Total/[Cu]Total.

    Se estudia la solubilidad del Cu(II en el sistema CuCl2-NH4Cl-NH3-H2O para concentraciones de cloruro inferiores a 4 molal en el intervalo de temperaturas 25-60 °C. Los resultados experimentales muestran que, para concentraciones de cloruros comprendidas entre 3,0 y 1,0 molal, la solubilidad cúprica viene determinada por la solubilidad del hidroxicloruro cúprico, Cu(OH1.5Cl0.5. Para concentraciones de cloruro 4,0 molal, existen dos compuestos cúpricos, el hidroxicloruro, Cu(OH1.5Cl0.5 o el cloruro de diamina, Cu(NH32Cl2, de los que, de acuerdo con la temperatura y con el valor de la relación [NH3]Total/[Cu]Total depende la solubilidad del Cu(II.

  19. The influence of three-dimensional capillary-porous coatings on heat transfer at liquid boiling

    Science.gov (United States)

    Surtaev, A. S.; Pavlenko, A. N.; Kalita, V. I.; Kuznetsov, D. V.; Komlev, D. I.; Radyuk, A. A.; Ivannikov, A. Yu.

    2016-04-01

    The process of heat transfer at pool boiling of liquid (Freon R21) on tubes with three-dimensional plasma-deposited capillary-porous coatings of various thicknesses has been experimentally studied. Comparative analysis of experimental data showed that the heat transfer coefficient for a heater tube with a 500-μm-thick porous coating is more than twice as large as that in liquid boiling on an otherwise similar uncoated tube. At the same time, no intensification of heat exchange in the regime of bubble boiling is observed on a tube with a 100-μm-thick porous coating.

  20. Pressure gradients and boiling as mechanisms for localizing ore in porphyry systems

    Science.gov (United States)

    Cunningham, Charles G.

    1978-01-01

    Fluid inclusions in ore zones of porphyry systems indicate that extensive boiling of hydrothermal fluids accompanies deposition of ore and gangue minerals. The boiling commonly accompanied a change from a lithostatic to a hydrostatic environment during evolution of an epizonal stock. Pressure gradients near the margin of the stock can determine whether ore or only a diffuse zone of mineralization is formed. A sharp drop in pressure in an epizonal environment is more likely to cause extensive boiling than a comparable change in a deeper environment, as the slope of the boiling curve steepens with an increase 'in pressure. The drop in pressure causes the hydrothermal fluids to boil and creates a crackle (stockwork) breccia, which hosts the veinlets of gangue quartz and ore minerals. The boiling selectively partitions CO2, H2S, and HCl into the vapor phase, changing the pH, composition, ionic strength, and thus the solubility product of metal complexes in the remaining liquid and causing the ore and gangue to come out of solution. Fluid inclusions trapped from boiling solutions can exhibit several forms, depending on the physical and chemical conditions of the hydrothermal fluid from which they were trapped. In one case, inclusions when heated can homogenize to either liquid or vapor at the same temperature, which is the true boiling temperature. In another case, homogenization of various inclusions can occur through a range of temperatures. The latter case results from the trapping of mixture of liquid and vapor. Variations in salinity can result from boiling of the hydrothermal fluid, or intermittent incorporation of high-salinity fluids from the magma, or trapping of fluids of varying densities at pressure-temperature conditions above the critical point of the fluid. In places, paleopressure-temperature transition zones can be recognized by fluid-inclusion homogenization temperatures and phase relationships and by the presence of anhydrite daughter minerals

  1. Heat transfer enhancement and surface thermostabilization for pool boiling on porous structures

    Directory of Open Access Journals (Sweden)

    Wojcik Tadeusz Michal

    2012-04-01

    Full Text Available The scope of the article includes the description of the experimental setup, methodology of the experimental studies, the study results for pool boiling heat transfer coefficient encountered on sintered capillary porous coverings. The results of own studies presented here refer to the boiling in a large volume on copper fibrous coverings. Hysteresis type I, II and III were described. Several examples of capillary porous surface coverings applications in purposely chosen complex boiling heat transfer processes have been presented based on Wojcik and Poniewski patents.

  2. Experimental Study on Convective Boiling Heat Transfer in Vertical Narrow Gap Annular Tube

    Institute of Scientific and Technical Information of China (English)

    Li Bin; He Anding; Wang Yueshe; Zhou Fangde

    2001-01-01

    Experiments are conducted to investigate the characteristics of single-phase forced-flow convection and boiling heat transfer of R113 flowing through annular tube with gap of 1, 1.5 and 2.5 mm, and also the visualization test are carried out to get two-phase flow regime. The data show that the Nusselt numbers for the narrow-gap are higher than those predicted by traditional large channel correlation and boiling heat transfer is enhanced. Based on the data obtained in this investigation, correlations for single-phase, forced convection and flow boiling in annular tube of different gap size has been developed.

  3. Fourier and Wavelet Transform Analysis of Pressure Signals during Explosive Boiling

    Institute of Scientific and Technical Information of China (English)

    YIN Tie-Nan; HUAI Xiu-Lan

    2008-01-01

    @@ The transient pressure in a liquid-pool during explosive boiling of acetone is measured by a micro-pressure-measuring system.The Fast Fourier transform and continuous wavelet transform methods are applied to investigate the frequency characteristics.The results show that the dominant frequency of the explosive boiling is 0-2MHz,and the bubble cluster formed by numerous tiny bubbles departs twice.Analysis and discussions are also conducted to explain the bubble evolution during the explosive boiling.

  4. Comprehensive Evaluation and Prediction of Enhancement of Boiling Heat Transfer with Additives

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A model of evaluation and prediction of enhancement of boiling heat transfer with additives has been propoeed according to fuzzy fundamentals. Correlative appraisement of boiling heat transfer augmentation was done with the model based on 39 additives which were tested by the authors and other researchers. The results show that the evaluation of 35 additives is consistent with experiments, which means that the accuracy of the model is 89.7 percent. In addition, the prediction of the ability of boiling heat transfer enhancement with sodium oleate,polyethylene glycol and Tween-40 is also in good agreement with correspondent experiments.

  5. Pool boiling on the superhydrophilic surface with TiO2 nanotube arrays

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Surface with TiO2 nanotube arrays(TNTAs)is superhydrophilic and of great specific area.This paper investigates the pool boiling characteristics at the thermal interface with TNTAs.The results show that the TNTAs interface can enhance the pool boiling heat transfer compared to the pure Ti metal plate.The bubbles formed at the initial nucleation state are very small and released in higher frequency.The pool boiling heat transfer enhancement at the TNTAs interface may be attributed to the high density of nucleate site,high intrinsic heating area of nanotubes layer,superhydrophilicity and the vertically oriented nanotube structure.

  6. Rapid transient explosive boiling of binary mixture under pulsed-laser irradiation

    Institute of Scientific and Technical Information of China (English)

    淮秀兰; 刘登瀛; 董兆一; 金仁喜; 王国祥

    2003-01-01

    Rapid transient explosive boiling of mixed ethanol and acetone of different volume fractions were investigated experimentally. The temperature of the metal film surface irradiated by a pulse laser was measured by a fast-response measurement system with a platinum film resistor. The behaviors of bubbles, including their formation, growth, departure and floating-up, were observed and captured by a microscope camera system. It was found that bubble nucleation temperature depends strongly on the heating rate. Some special characteristics different from those of conventional boiling were revealed, and the factors affecting explosive boiling were studied.

  7. Observation on rapid transient explosive boiling under pulsed-laser heating

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Using various kinds of liquids (pure acetone, binary mixtures in various volume fractions of ethanol and acetone) as working liquids, the experiments of rapid transient explosive boiling induced by pulsed-laser irradiation are carried out. The temperature field on a microsecond scale is measured, and the behavior of bubbles is observed and captured by a microscopic camera system. The extreme characteristics that differ from those in normal boiling are clearly revealed. The influence of working liquid species, volume fraction of the mixture, nanoparticles added in the working liquid, and the laser irradiation parameters on the boiling behavior are also studied.

  8. A study of the corrosion products of mild steel in high ionic strength brines.

    Science.gov (United States)

    Wang, Z; Moore, R C; Felmy, A R; Mason, M J; Kukkadapu, R K

    2001-01-01

    The corrosion layer on steel surfaces that formed after exposure to waste isolation pilot plant (WIPP) brines under anoxic conditions was characterized for chemical composition, thickness and phase composition. The chemical composition of the corrosion layer was determined both by X-ray photoelectron spectroscopy (XPS) and by chemical analysis of acid solutions used to remove the corrosion layer. Atomic force microscopic (AFM) images indicated that the brine-corroded surface layer shows extensive granulation along the contours of the steel surface that is characteristic of sharp polishing marks. The corrosion layer seemed to be porous and could be dissolved and detached in dilute hydrochloric acid. The corrosion layer appears to be composed of iron oxides with some ionic substitutions from the brines. The 77 K Mössbauer spectrum recorded for iron powder leached under similar conditions indicated the corrosion layer was comprised principally of green rust.

  9. Prediction of oxygen solubility in pure water and brines up to high temperatures and pressures

    Science.gov (United States)

    GENG, Ming; DUAN, Zhenhao

    2010-10-01

    A thermodynamic model is presented to calculate the oxygen solubility in pure water (273-600 K, 0-200 bar) and natural brines containing Na +, K +, Ca 2+, Mg 2+, Cl -, SO 42-, over a wide range of temperature, pressure and ionic strength with or close to experimental accuracy. This model is based on an accurate equation of state to calculate vapor phase chemical potential and a specific particle interaction model for liquid phase chemical potential. With this approach, the model can not only reproduce the existing experimental data, but also extrapolate beyond the data range from simple aqueous salt system to complicated brine systems including seawater. Compared with previous models, this model covers much wider temperature and pressure space in variable composition brine systems. A program for this model can be downloaded from the website: http://www.geochem-model.org.

  10. Brine migration resulting from pressure increases in a layered subsurface system

    Science.gov (United States)

    Delfs, Jens-Olaf; Nordbeck, Johannes; Bauer, Sebastian

    2016-04-01

    Brine originating from the deep subsurface impairs parts of the freshwater resources in the North German Basin. Some of the deep porous formations (esp. Trias and Jurassic) exhibit considerable storage capacities for waste fluids (CO2, brine from oil production or cavern leaching), raising concerns among water providers that this type of deep subsurface utilization might impair drinking water supplies. On the one hand, overpressures induced by fluid injections and the geothermal gradient support brine migration from deep into shallow formations. On the other hand, the rising brine is denser than the surrounding less-saline formation waters and, therefore, tends to settle down. Aim of this work is to investigate the conditions under which pressurized formation brine from deep formations can reach shallow freshwater resources. Especially, the role of intermediate porous formations between the storage formation and the groundwater is studied. For this, complex thermohaline simulations using a coupled numerical process model are necessary and performed in this study, in which fluid density depends on fluid pressure, temperature and salt content and the governing partial differential equations are coupled. The model setup is 2D and contains a hypothetic series of aquifers and barriers, each with a thickness of 200 m. Formation pressure is increased at depths of about 2000 m in proximity to a salt wall and a permeable fault. The domain size reaches up to tens of kilometers horizontally to the salt wall. The fault connects the injection formation and the freshwater aquifer such that conditions can be considered as extremely favorable for induced brine migration (worst case scenarios). Brine, heat, and salt fluxes are quantified with reference to hydraulic permeabilities, storage capacities (in terms of domain size), initial salt and heat distribution, and operation pressures. The simulations reveal the development of a stagnation point in the fault region in each

  11. Salinity fluctuation of the brine discharge affects growth and survival of the seagrass Cymodocea nodosa.

    Science.gov (United States)

    Garrote-Moreno, A; Fernández-Torquemada, Y; Sánchez-Lizaso, J L

    2014-04-15

    The increase of seawater desalination plants may affect seagrasses as a result of its hypersaline effluents. There are some studies on the salinity tolerance of seagrasses under controlled laboratory conditions, but few have been done in situ. To this end, Cymodocea nodosa shoots were placed during one month at four localities: two close to a brine discharge; and the other two not affected by the discharge, and this experiment was repeated four times. The results obtained showed a decrease in growth and an increased mortality at the localities affected by the brine discharge. An increase was detected in the percentage of horizontal shoots in respect to vertical shoots at the impacted localities. It is probably that not only the average salinity, but also the constant salinity fluctuations and slightly higher temperatures associated with the brine that may have caused physiological stress thus reducing C. nodosa growth and survival.

  12. FIELD IMPLEMENTATION PLAN FOR A WILLISTON BASIN BRINE EXTRACTION AND STORAGE TEST

    Energy Technology Data Exchange (ETDEWEB)

    Hamling, John; Klapperich, Ryan; Stepan, Daniel; Sorensen, James; Pekot, Lawrence; Peck, Wesley; Jacobson, Lonny; Bosshart, Nicholas; Hurley, John; Wilson, William; Kurz, Marc; Burnison, Shaughn; Salako, Olarinre; Musich, Mark; Botnen, Barry; Kalenze, Nicholas; Ayash, Scott; Ge, Jun; Jiang, Tao; Dalkhaa, Chantsalmaa; Oster, Benjamin; Peterson, Kyle; Feole, Ian; Gorecki, Charles; Steadman, Edward

    2016-03-31

    The Energy & Environmental Research Center (EERC) successfully completed all technical work of Phase I, including development of a field implementation plan (FIP) for a brine extraction and storage test (BEST) in the North Dakota portion of the Williston Basin. This implementation plan was commissioned by the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) as a proxy for managing formation pressure plumes and measuring/monitoring the movement of differential pressure and CO2 plumes in the subsurface for future saline CO2 storage projects. BEST comprises the demonstration and validation of active reservoir management (ARM) strategies and extracted brine treatment technologies. Two prospective commercial brine injection sites were evaluated for BEST to satisfy DOE’s goals. Ultimately, an active saltwater disposal (SWD) site, Johnsons Corner, was selected because it possesses an ideal combination of key factors making it uniquely suited to host BEST. This site is located in western North Dakota and operated by Nuverra Environmental Solutions (Nuverra), a national leader in brine handling, treatment, and injection. An integrated management approach was used to incorporate local and regional geologic characterization activities with geologic and simulation models, inform a monitoring, verification, and accounting (MVA) plan, and to conduct a risk assessment. This approach was used to design a FIP for an ARM schema and an extracted brine treatment technology test bed facility. The FIP leverages an existing pressure plume generated by two commercial SWD wells. These wells, in conjunction with a new brine extraction well, will be used to conduct the ARM schema. Results of these tests will be quantified based on their impact on the performance of the existing SWD wells and the surrounding reservoir system. Extracted brine will be injected into an underlying deep saline formation through a new injection well. The locations of proposed

  13. A deep sea community at the Kebrit brine pool in the Red Sea

    KAUST Repository

    Vestheim, Hege

    2015-02-26

    Approximately 25 deep sea brine pools occur along the mid axis of the Red Sea. These hypersaline, anoxic, and acidic environments have previously been reported to host diverse microbial communities. We visited the Kebrit brine pool in April 2013 and found macrofauna present just above the brine–seawater interface (~1465 m). In particular, inactive sulfur chimneys had associated epifauna of sea anemones, sabellid type polychaetes, and hydroids, and infauna consisting of capitellid polychaetes, gastropods of the genus Laeviphitus (fam. Elachisinidae), and top snails of the family Cocculinidae. The deep Red Sea generally is regarded as extremely poor in benthos. We hypothesize that the periphery along the Kebrit holds increased biomass and biodiversity that are sustained by prokaryotes associated with the brine pool or co-occurring seeps.

  14. Imaged brine inclusions in young sea ice—Shape, distribution and formation timing

    DEFF Research Database (Denmark)

    Galley, R.J.; Else, B.G.T.; Geilfus, Nicolas-Xavier

    2015-01-01

    Liquid inclusions in sea ice are variable and dependent on the myriad of physical conditions of the atmosphere– sea ice environment in which the sea ice was grown, and whether or not melting processes affected the sea ice. In that light, there exist relatively few observations and resultant...... quantification of the morphology and vertical dis- tribution of brine inclusions in sea ice. Using a magnetic (3.0 T) resonance (MR) imager using constructive inter- ference steady state gradient echo sequence, we show that it is possible to image brine channels and pockets in an 18.5 cm young sea ice core...... in three-dimensions in only four and a half minutes following core storage at − 20 °C. We present a three-dimensional image of a brine drainage channel feature in a young sea ice core, give the phys- ical context for its formation by presenting the physical conditions of the atmosphere and water/sea ice...

  15. Effects of sodium citrate plus sodium diacetate and buffered vinegar on Escherichia coli O157:H7 and psychrotrophic bacteria in brine-injected beef.

    Science.gov (United States)

    Ponrajan, Amudhan; Harrison, Mark A; Segers, Jacob R; Lowe, Bradley K; McKeith, Russell O; Pringle, T Dean; Martino, Karina G; Mulligan, Jake H; Stelzleni, Alexander M

    2011-03-01

    The objective of this research was to examine the effects of sodium citrate plus sodium diacetate or buffered vinegar on Escherichia coli O157:H7 and psychrotrophic bacteria when incorporated in brine solutions for injected beef. Two experiments were conducted in which 30 top rounds and 30 top sirloins were injected (110%) to contain (i) 0.5% sodium chloride and 0.4% sodium tripolyphosphate as the control (CNT); (ii) CNT with a 1% solution of 80% sodium citrate plus 20% sodium diacetate (SC + D); or (iii) CNT with 2% buffered vinegar (VIN) in the final product. For the E. coli challenge, muscles were surface inoculated to target 6 log CFU/cm(2). After injection and 10 days of storage in a vacuum package (4°C), one half of each muscle was sampled raw and the other half was cooked to an internal temperature of 60°C with a 12-min hold. For raw samples, a significant reduction of 0.6 and 1.0 log CFU/g of E. coli O157:H7 was observed in both SC + D- and VIN-injected top rounds and sirloins, respectively. All cooked samples were E. coli O157:H7 negative. For psychrotrophic analysis, subprimals were injected and vacuum packaged for 10 days at 0 ± 1°C. After 10 days of storage, steaks were fabricated and placed in aerobic display (4 ± 1°C) for 1, 7, 14, and 21 days. Psychrotrophic organism growth was restricted in SC + D and VIN samples when compared with CNT on all days except day 1. Sodium citrate plus sodium diacetate or buffered vinegar may improve the safety and shelf life of multineedle brine-injected beef.

  16. The CPA Equation of State and an Activity Coefficient Model for Accurate Molar Enthalpy Calculations of Mixtures with Carbon Dioxide and Water/Brine

    Energy Technology Data Exchange (ETDEWEB)

    Myint, P. C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hao, Y. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Firoozabadi, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-03-27

    Thermodynamic property calculations of mixtures containing carbon dioxide (CO2) and water, including brines, are essential in theoretical models of many natural and industrial processes. The properties of greatest practical interest are density, solubility, and enthalpy. Many models for density and solubility calculations have been presented in the literature, but there exists only one study, by Spycher and Pruess, that has compared theoretical molar enthalpy predictions with experimental data [1]. In this report, we recommend two different models for enthalpy calculations: the CPA equation of state by Li and Firoozabadi [2], and the CO2 activity coefficient model by Duan and Sun [3]. We show that the CPA equation of state, which has been demonstrated to provide good agreement with density and solubility data, also accurately calculates molar enthalpies of pure CO2, pure water, and both CO2-rich and aqueous (H2O-rich) mixtures of the two species. It is applicable to a wider range of conditions than the Spycher and Pruess model. In aqueous sodium chloride (NaCl) mixtures, we show that Duan and Sun’s model yields accurate results for the partial molar enthalpy of CO2. It can be combined with another model for the brine enthalpy to calculate the molar enthalpy of H2O-CO2-NaCl mixtures. We conclude by explaining how the CPA equation of state may be modified to further improve agreement with experiments. This generalized CPA is the basis of our future work on this topic.

  17. Models and Stability Analysis of Boiling Water Reactors

    Energy Technology Data Exchange (ETDEWEB)

    John Dorning

    2002-04-15

    We have studied the nuclear-coupled thermal-hydraulic stability of boiling water reactors (BWRs) using a model that includes: space-time modal neutron kinetics based on spatial w-modes; single- and two-phase flow in parallel boiling channels; fuel rod heat conduction dynamics; and a simple model of the recirculation loop. The BR model is represented by a set of time-dependent nonlinear ordinary differential equations, and is studied as a dynamical system using the modern bifurcation theory and nonlinear dynamical systems analysis. We first determine the stability boundary (SB) - or Hopf bifurcation set- in the most relevant parameter plane, the inlet-subcooling-number/external-pressure-drop plane, for a fixed control rod induced external reactivity equal to the 100% rod line value; then we transform the SB to the practical power-flow map used by BWR operating engineers and regulatory agencies. Using this SB, we show that the normal operating point at 100% power is very stable, that stability of points on the 100% rod line decreases as the flow rate is reduced, and that operating points in the low-flow/high-power region are least stable. We also determine the SB that results when the modal kinetics is replaced by simple point reactor kinetics, and we thereby show that the first harmonic mode does not have a significant effect on the SB. However, we later show that it nevertheless has a significant effect on stability because it affects the basin of attraction of stable operating points. Using numerical simulations we show that, in the important low-flow/high-power region, the Hopf bifurcation that occurs as the SB is crossed is subcritical; hence, growing oscillations can result following small finite perturbations of stable steady-states on the 100% rod line at points in the low-flow/high-power region. Numerical simulations are also performed to calculate the decay ratios (DRs) and frequencies of oscillations for various points on the 100% rod line. It is

  18. Laboratory flow experiments for visualizing carbon dioxide-induced, density-driven brine convection

    Energy Technology Data Exchange (ETDEWEB)

    Kneafsey, T.; Pruess, K.

    2009-09-01

    Injection of carbon dioxide (CO{sub 2}) into saline aquifers confined by low-permeability cap rock will result in a layer of CO{sub 2} overlying the brine. Dissolution of CO{sub 2} into the brine increases the brine density, resulting in an unstable situation in which more-dense brine overlies less-dense brine. This gravitational instability could give rise to density-driven convection of the fluid, which is a favorable process of practical interest for CO{sub 2} storage security because it accelerates the transfer of buoyant CO{sub 2} into the aqueous phase, where it is no longer subject to an upward buoyant drive. Laboratory flow visualization tests in transparent Hele-Shaw cells have been performed to elucidate the processes and rates of this CO{sub 2} solute-driven convection (CSC). Upon introduction of CO{sub 2} into the system, a layer of CO{sub 2}-laden brine forms at the CO{sub 2}-water interface. Subsequently, small convective fingers form, which coalesce, broaden, and penetrate into the test cell. Images and time-series data of finger lengths and wavelengths are presented. Observed CO{sub 2} uptake of the convection system indicates that the CO{sub 2} dissolution rate is approximately constant for each test and is far greater than expected for a diffusion-only scenario. Numerical simulations of our system show good agreement with the experiments for onset time of convection and advancement of convective fingers. There are differences as well, the most prominent being the absence of cell-scale convection in the numerical simulations. This cell-scale convection observed in the experiments is probably initiated by a small temperature gradient induced by the cell illumination.

  19. Brine assemblages of ultrasmall microbial cells within the ice cover of Lake Vida, Antarctica.

    Science.gov (United States)

    Kuhn, Emanuele; Ichimura, Andrew S; Peng, Vivian; Fritsen, Christian H; Trubl, Gareth; Doran, Peter T; Murray, Alison E

    2014-06-01

    The anoxic and freezing brine that permeates Lake Vida's perennial ice below 16 m contains an abundance of very small (≤0.2-μm) particles mixed with a less abundant population of microbial cells ranging from >0.2 to 1.5 μm in length. Fluorescent DNA staining, electron microscopy (EM) observations, elemental analysis, and extraction of high-molecular-weight genomic DNA indicated that a significant portion of these ultrasmall particles are cells. A continuous electron-dense layer surrounding a less electron-dense region was observed by EM, indicating the presence of a biological membrane surrounding a cytoplasm. The ultrasmall cells are 0.192 ± 0.065 μm, with morphology characteristic of coccoid and diplococcic bacterial cells, often surrounded by iron-rich capsular structures. EM observations also detected the presence of smaller unidentified nanoparticles of 0.020 to 0.140 μm among the brine cells. A 16S rRNA gene clone library from the brine 0.1- to 0.2-μm-size fraction revealed a relatively low-diversity assemblage of Bacteria sequences distinct from the previously reported >0.2-μm-cell-size Lake Vida brine assemblage. The brine 0.1- to 0.2-μm-size fraction was dominated by the Proteobacteria-affiliated genera Herbaspirillum, Pseudoalteromonas, and Marinobacter. Cultivation efforts of the 0.1- to 0.2-μm-size fraction led to the isolation of Actinobacteria-affiliated genera Microbacterium and Kocuria. Based on phylogenetic relatedness and microscopic observations, we hypothesize that the ultrasmall cells in Lake Vida brine are ultramicrocells that are likely in a reduced size state as a result of environmental stress or life cycle-related conditions.

  20. Oxomemazine hydro­chloride

    Science.gov (United States)

    Siddegowda, M. S.; Butcher, Ray J.; Akkurt, Mehmet; Yathirajan, H. S.; Ramesh, A. R.

    2011-01-01

    In the title compound [systematic name: 3-(5,5-dioxo­phen­othia­zin-10-yl)-N,N,2-trimethyl­propanaminium chloride], C18H23N2O2S+·Cl−, the dihedral angle between the two outer aromatic rings of the phenothia­zine unit is 30.5 (2)°. In the crystal, the components are linked by N—H⋯Cl and C—H⋯Cl hydrogen bonds and C—H⋯π inter­actions. PMID:22090928