Application of EB in Japan

International Nuclear Information System (INIS)

Sunaga, Hiromi

2003-01-01

Radiation processing using electron beam (EB) facilities other than gamma-ray facilities in Japan is introduced. After briefly presented the features of EB compared with gamma ray, present status of EB application is described. Polymerized materials for use of wire, cable, radial tire, heat shrinkable tube, foam polyethylene, PTFE, battery separator, and adsorbent material are known to be resulting from cross-linking, decomposition, and graft polymerization reactions. Environmental preservation includes electron flue gas treatment in the coal- or oil-fired power plants, research for volatile organic compounds (VOC) and dioxins, as well as wastewater and sludge treatment. Finally activity of JAERI in the related fields is overviewed with the authors prospects for utilization of low energy EB with low cost for surface treatment and functional materials. (S. Ohno)

Application of EB in Japan

Energy Technology Data Exchange (ETDEWEB)

Sunaga, Hiromi [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

2003-02-01

Radiation processing using electron beam (EB) facilities other than gamma-ray facilities in Japan is introduced. After briefly presented the features of EB compared with gamma ray, present status of EB application is described. Polymerized materials for use of wire, cable, radial tire, heat shrinkable tube, foam polyethylene, PTFE, battery separator, and adsorbent material are known to be resulting from cross-linking, decomposition, and graft polymerization reactions. Environmental preservation includes electron flue gas treatment in the coal- or oil-fired power plants, research for volatile organic compounds (VOC) and dioxins, as well as wastewater and sludge treatment. Finally activity of JAERI in the related fields is overviewed with the authors prospects for utilization of low energy EB with low cost for surface treatment and functional materials. (S. Ohno)

Adhesion and interface problems of EB-PVD thermal barrier coatings; Grenzschichtproblematik und Haftung von EB-PVD-Waermedaemmschichtsystemen

Energy Technology Data Exchange (ETDEWEB)

Fritscher, K.; Leyens, C. [Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Koeln (Germany). Inst. fuer Werkstoff-Forschung

1996-12-31

Loss of adhesion in thermal insulation layers produced by EB-PVD may be caused by surface morphologies or oxide phases resulting from previous process stages, e.g. shot peening, or inappropriate annealing conditions. These undesirable oxide phases are mostly spinels and silicates which pose mechanical problems. Annealing and densification must be modified in order to promote the formation of {alpha}-Al{sub 2}O{sub 3} layers. It may also be possible to avoid certain categories of flaws by changing one material partner (e.g. by using {beta}-NiAl-free adhesive layers). [Deutsch] Die Ursachen der Einbussen der Haftung in WDS-Systemen aus EB-PVD-Fertigung liegen oft in der Ausbildung von Oberflaechenmorphologien oder von Oxidphasen begruendet, die aus den der WDS-Beschichtung vorangehenden Verfahrensschritten wie z.B. des Glasperlstrahlens und von unangemessenen Gluehbedingungen herruehren koennen. Bei diesen unerwuenschten Oxidphasen handelt es sich u.a. um Spinelle und Silikate, die in mechanischer Hinsicht problematisch sind. Glueh- und Verdichtungsroutinen sind entsprechend zu modifizieren, um die Bildung von {alpha}-Al{sub 2}O{sub 3}-Schichten zu foerdern. Moeglicherweise sind gewisse Fehlerkategorien bereits dadurch zu umgehen, dass ein Materialpartner geaendert wird (Beispiel: {beta}-NiAl-freie Haftschichten anwenden). (orig.)

47 CFR 27.1203 - EBS programming requirements.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false EBS programming requirements. 27.1203 Section....1203 EBS programming requirements. (a) Except as provided in paragraphs (b), (c), and (d) of this section, BRS and EBS licensees are authorized to provide fixed or mobile service, except aeronautical...

Self-organization phenomena in embryonic stem cell-derived embryoid bodies: axis formation and breaking of symmetry during cardiomyogenesis.

Science.gov (United States)

Fuchs, Christiane; Scheinast, Matthias; Pasteiner, Waltraud; Lagger, Sabine; Hofner, Manuela; Hoellrigl, Alexandra; Schultheis, Martina; Weitzer, Georg

2012-01-01

Aggregation of embryonic stem cells gives rise to embryoid bodies (EBs) which undergo developmental processes reminiscent of early eutherian embryonic development. Development of the three germ layers suggests that gastrulation takes place. In vivo, gastrulation is a highly ordered process but in EBs only few data support the hypothesis that self-organization of differentiating cells leads to morphology, reminiscent of the early gastrula. Here we demonstrate that a timely implantation-like process is a prerequisite for the breaking of the radial symmetry of suspended EBs. Attached to a surface, EBs develop a bilateral symmetry and presumptive mesodermal cells emerge between the center of the EBs and a horseshoe-shaped ridge of cells. The development of an epithelial sheet of cells on one side of the EBs allows us to define an 'anterior' and a 'posterior' end of the EBs. In the mesodermal area, first cardiomyocytes (CMCs) develop mainly next to this epithelial sheet of cells. Development of twice as many CMCs at the 'left' side of the EBs breaks the bilateral symmetry and suggests that cardiomyogenesis reflects a local or temporal asymmetry in EBs. The asymmetric appearance of CMCs but not the development of mesoderm can be disturbed by ectopic expression of the muscle-specific protein Desmin. Later, the bilateral morphology becomes blurred by an apparently chaotic differentiation of many cell types. The absence of comparable structures in aggregates of cardiovascular progenitor cells isolated from the heart demonstrates that the self-organization of cells during a gastrulation-like process is a unique feature of embryonic stem cells. Copyright © 2011 S. Karger AG, Basel.

Study on the heat-resistant EB curing composites

International Nuclear Information System (INIS)

Bao Jianwen; Li Yang; Li Fengmei

2000-01-01

There are many advantages in the EB-curing process of composites. Heat-resistant EB-curing composites could substitute for polyimide composites used in aeronautical engine. The effects of catalyst and dose on the cured resin were investigated. The heat-resistance of the resin cured by EB was evaluated by dynamic mechanical thermal analysis (DMTA). The experiment result shows that the mechanical property of the composites cured by EB could meet the needs of the aeronautical engine in 250degC. (author)

EB curable laminating adhesives

International Nuclear Information System (INIS)

Matsuyama, Asao; Kobayashi, Masahide; Gotoh, Sakiko

1992-01-01

New developed solvent free EB curable laminating adhesives have two liquid components, A with hydroxy and acryloyl group, B with isocyanate and acryloyl group in a molecule. These EB laminating adhesives do not need any aging process, which is a big advantage, and are very suitable for environment, safety, and health because of no heating process and solvent free formulas. And we have made basic research about the relation of peel strength or heat seal strength versus Tg of cured film, elongation at break, elastic modulus, and so on. Basic specifications of the new developed adhesives are shown. (author)

Protective effects of ebselen (Ebs) and para-aminosalicylic acid (PAS) against manganese (Mn)-induced neurotoxicity

Energy Technology Data Exchange (ETDEWEB)

Marreilha dos Santos, A.P., E-mail: apsantos@ff.ul.pt [I-Med.UL, Department of Toxicology and Food Sciences, Faculty of Pharmacy, University of Lisbon, Lisbon (Portugal); Lucas, Rui L.; Andrade, Vanda; Mateus, M. Luísa [I-Med.UL, Department of Toxicology and Food Sciences, Faculty of Pharmacy, University of Lisbon, Lisbon (Portugal); Milatovic, Dejan; Aschner, Michael [Department of Pediatrics, Vanderbilt University Medical Center, Nashville, TN 37232 (United States); Batoreu, M. Camila [I-Med.UL, Department of Toxicology and Food Sciences, Faculty of Pharmacy, University of Lisbon, Lisbon (Portugal)

2012-02-01

Chronic, excessive exposure to manganese (Mn) may induce neurotoxicity and cause an irreversible brain disease, referred to as manganism. Efficacious therapies for the treatment of Mn are lacking, mandating the development of new interventions. The purpose of the present study was to investigate the efficacy of ebselen (Ebs) and para-aminosalicylic acid (PAS) in attenuating the neurotoxic effects of Mn in an in vivo rat model. Exposure biomarkers, inflammatory and oxidative stress biomarkers, as well as behavioral parameters were evaluated. Co-treatment with Mn plus Ebs or Mn plus PAS caused a significant decrease in blood and brain Mn concentrations (compared to rats treated with Mn alone), concomitant with reduced brain E{sub 2} prostaglandin (PGE{sub 2}) and enhanced brain glutathione (GSH) levels, decreased serum prolactin (PRL) levels, and increased ambulation and rearing activities. Taken together, these results establish that both PAS and Ebs are efficacious in reducing Mn body burden, neuroinflammation, oxidative stress and locomotor activity impairments in a rat model of Mn-induced toxicity. -- Highlights: ► The manuscript is unique in its approach to the neurotoxicity of Mn. ► The manuscript incorporates molecular, cellular and functional (behavioral) analyses. ► Both PAS and Ebs are effective in restoring Mn behavioral function. ► Both PAS and Ebs are effective in reducing Mn-induced oxidative stress. ► Both PAS and Ebs led to a decrease in Mn-induced neuro-inflammation.

Protective effects of ebselen (Ebs) and para-aminosalicylic acid (PAS) against manganese (Mn)-induced neurotoxicity

International Nuclear Information System (INIS)

Marreilha dos Santos, A.P.; Lucas, Rui L.; Andrade, Vanda; Mateus, M. Luísa; Milatovic, Dejan; Aschner, Michael; Batoreu, M. Camila

2012-01-01

Chronic, excessive exposure to manganese (Mn) may induce neurotoxicity and cause an irreversible brain disease, referred to as manganism. Efficacious therapies for the treatment of Mn are lacking, mandating the development of new interventions. The purpose of the present study was to investigate the efficacy of ebselen (Ebs) and para-aminosalicylic acid (PAS) in attenuating the neurotoxic effects of Mn in an in vivo rat model. Exposure biomarkers, inflammatory and oxidative stress biomarkers, as well as behavioral parameters were evaluated. Co-treatment with Mn plus Ebs or Mn plus PAS caused a significant decrease in blood and brain Mn concentrations (compared to rats treated with Mn alone), concomitant with reduced brain E 2 prostaglandin (PGE 2 ) and enhanced brain glutathione (GSH) levels, decreased serum prolactin (PRL) levels, and increased ambulation and rearing activities. Taken together, these results establish that both PAS and Ebs are efficacious in reducing Mn body burden, neuroinflammation, oxidative stress and locomotor activity impairments in a rat model of Mn-induced toxicity. -- Highlights: ► The manuscript is unique in its approach to the neurotoxicity of Mn. ► The manuscript incorporates molecular, cellular and functional (behavioral) analyses. ► Both PAS and Ebs are effective in restoring Mn behavioral function. ► Both PAS and Ebs are effective in reducing Mn-induced oxidative stress. ► Both PAS and Ebs led to a decrease in Mn-induced neuro-inflammation.

Superior Red Blood Cell Generation from Human Pluripotent Stem Cells Through a Novel Microcarrier-Based Embryoid Body Platform.

Science.gov (United States)

Sivalingam, Jaichandran; Lam, Alan Tin-Lun; Chen, Hong Yu; Yang, Bin Xia; Chen, Allen Kuan-Liang; Reuveny, Shaul; Loh, Yuin-Han; Oh, Steve Kah-Weng

2016-08-01

In vitro generation of red blood cells (RBCs) from human embryonic stem cells and human induced pluripotent stem cells appears to be a promising alternate approach to circumvent shortages in donor-derived blood supplies for clinical applications. Conventional methods for hematopoietic differentiation of human pluripotent stem cells (hPSC) rely on embryoid body (EB) formation and/or coculture with xenogeneic cell lines. However, most current methods for hPSC expansion and EB formation are not amenable for scale-up to levels required for large-scale RBC generation. Moreover, differentiation methods that rely on xenogenic cell lines would face obstacles for future clinical translation. In this study, we report the development of a serum-free and chemically defined microcarrier-based suspension culture platform for scalable hPSC expansion and EB formation. Improved survival and better quality EBs generated with the microcarrier-based method resulted in significantly improved mesoderm induction and, when combined with hematopoietic differentiation, resulted in at least a 6-fold improvement in hematopoietic precursor expansion, potentially culminating in a 80-fold improvement in the yield of RBC generation compared to a conventional EB-based differentiation method. In addition, we report efficient terminal maturation and generation of mature enucleated RBCs using a coculture system that comprised primary human mesenchymal stromal cells. The microcarrier-based platform could prove to be an appealing strategy for future scale-up of hPSC culture, EB generation, and large-scale generation of RBCs under defined and xeno-free conditions.

The Key Enzyme of the Sialic Acid Metabolism Is Involved in Embryoid Body Formation and Expression of Marker Genes of Germ Layer Formation

Directory of Open Access Journals (Sweden)

Annett Thate

2013-10-01

Full Text Available The bi-functional enzyme UDP-N-acetyl-2-epimerase/N-acetylmannosamine kinase (GNE is the key enzyme of the sialic acid biosynthesis. Sialic acids are negatively charged nine carbon amino sugars and are found on most glycoproteins and many glycolipids in terminal positions, where they are involved in a variety of biological important molecular interactions. Inactivation of the GNE by homologous recombination results in early embryonic lethality in mice. Here, we report that GNE-deficient embryonic stem cells express less differentiation markers compared to wild-type embryonic stem cells. As a result, GNE-deficient embryonic stem cells fail to form proper embryoid bodies (EB within the first day of culture. However, when culturing these cells in the presence of sialic acids for three days, also GNE-deficient embryonic stem cells form normal EBs. In contrast, when culturing these cells in sialic acid reduced medium, GNE-deficient embryonic stem cells proliferate faster and form larger EBs without any change in the expression of markers of the germ layers.

Recent status of EB applications in China

International Nuclear Information System (INIS)

Wang Zhiguang; Zhan Wenlong

2004-01-01

The advantages of energetic electron beam (EB) made it an attractive method for radiation processing of materials. In the present paper, the recent status of R and D of EB applications in China has demonstrated briefly. (author)

EBS Radionuclide Transport Abstraction

International Nuclear Information System (INIS)

J.D. Schreiber

2005-01-01

The purpose of this report is to develop and analyze the engineered barrier system (EBS) radionuclide transport abstraction model, consistent with Level I and Level II model validation, as identified in ''Technical Work Plan for: Near-Field Environment and Transport: Engineered Barrier System: Radionuclide Transport Abstraction Model Report Integration'' (BSC 2005 [DIRS 173617]). The EBS radionuclide transport abstraction (or EBS RT Abstraction) is the conceptual model used in the total system performance assessment for the license application (TSPA-LA) to determine the rate of radionuclide releases from the EBS to the unsaturated zone (UZ). The EBS RT Abstraction conceptual model consists of two main components: a flow model and a transport model. Both models are developed mathematically from first principles in order to show explicitly what assumptions, simplifications, and approximations are incorporated into the models used in the TSPA-LA. The flow model defines the pathways for water flow in the EBS and specifies how the flow rate is computed in each pathway. Input to this model includes the seepage flux into a drift. The seepage flux is potentially split by the drip shield, with some (or all) of the flux being diverted by the drip shield and some passing through breaches in the drip shield that might result from corrosion or seismic damage. The flux through drip shield breaches is potentially split by the waste package, with some (or all) of the flux being diverted by the waste package and some passing through waste package breaches that might result from corrosion or seismic damage. Neither the drip shield nor the waste package survives an igneous intrusion, so the flux splitting submodel is not used in the igneous scenario class. The flow model is validated in an independent model validation technical review. The drip shield and waste package flux splitting algorithms are developed and validated using experimental data. The transport model considers

EBS Radionuclide Transport Abstraction

Energy Technology Data Exchange (ETDEWEB)

J.D. Schreiber

2005-08-25

The purpose of this report is to develop and analyze the engineered barrier system (EBS) radionuclide transport abstraction model, consistent with Level I and Level II model validation, as identified in ''Technical Work Plan for: Near-Field Environment and Transport: Engineered Barrier System: Radionuclide Transport Abstraction Model Report Integration'' (BSC 2005 [DIRS 173617]). The EBS radionuclide transport abstraction (or EBS RT Abstraction) is the conceptual model used in the total system performance assessment for the license application (TSPA-LA) to determine the rate of radionuclide releases from the EBS to the unsaturated zone (UZ). The EBS RT Abstraction conceptual model consists of two main components: a flow model and a transport model. Both models are developed mathematically from first principles in order to show explicitly what assumptions, simplifications, and approximations are incorporated into the models used in the TSPA-LA. The flow model defines the pathways for water flow in the EBS and specifies how the flow rate is computed in each pathway. Input to this model includes the seepage flux into a drift. The seepage flux is potentially split by the drip shield, with some (or all) of the flux being diverted by the drip shield and some passing through breaches in the drip shield that might result from corrosion or seismic damage. The flux through drip shield breaches is potentially split by the waste package, with some (or all) of the flux being diverted by the waste package and some passing through waste package breaches that might result from corrosion or seismic damage. Neither the drip shield nor the waste package survives an igneous intrusion, so the flux splitting submodel is not used in the igneous scenario class. The flow model is validated in an independent model validation technical review. The drip shield and waste package flux splitting algorithms are developed and validated using experimental data. The transport

EBS Radionuclide Transport Abstraction

Energy Technology Data Exchange (ETDEWEB)

J. Prouty

2006-07-14

The purpose of this report is to develop and analyze the engineered barrier system (EBS) radionuclide transport abstraction model, consistent with Level I and Level II model validation, as identified in Technical Work Plan for: Near-Field Environment and Transport: Engineered Barrier System: Radionuclide Transport Abstraction Model Report Integration (BSC 2005 [DIRS 173617]). The EBS radionuclide transport abstraction (or EBS RT Abstraction) is the conceptual model used in the total system performance assessment (TSPA) to determine the rate of radionuclide releases from the EBS to the unsaturated zone (UZ). The EBS RT Abstraction conceptual model consists of two main components: a flow model and a transport model. Both models are developed mathematically from first principles in order to show explicitly what assumptions, simplifications, and approximations are incorporated into the models used in the TSPA. The flow model defines the pathways for water flow in the EBS and specifies how the flow rate is computed in each pathway. Input to this model includes the seepage flux into a drift. The seepage flux is potentially split by the drip shield, with some (or all) of the flux being diverted by the drip shield and some passing through breaches in the drip shield that might result from corrosion or seismic damage. The flux through drip shield breaches is potentially split by the waste package, with some (or all) of the flux being diverted by the waste package and some passing through waste package breaches that might result from corrosion or seismic damage. Neither the drip shield nor the waste package survives an igneous intrusion, so the flux splitting submodel is not used in the igneous scenario class. The flow model is validated in an independent model validation technical review. The drip shield and waste package flux splitting algorithms are developed and validated using experimental data. The transport model considers advective transport and diffusive transport

EBS Radionuclide Transport Abstraction

International Nuclear Information System (INIS)

J. Prouty

2006-01-01

The purpose of this report is to develop and analyze the engineered barrier system (EBS) radionuclide transport abstraction model, consistent with Level I and Level II model validation, as identified in Technical Work Plan for: Near-Field Environment and Transport: Engineered Barrier System: Radionuclide Transport Abstraction Model Report Integration (BSC 2005 [DIRS 173617]). The EBS radionuclide transport abstraction (or EBS RT Abstraction) is the conceptual model used in the total system performance assessment (TSPA) to determine the rate of radionuclide releases from the EBS to the unsaturated zone (UZ). The EBS RT Abstraction conceptual model consists of two main components: a flow model and a transport model. Both models are developed mathematically from first principles in order to show explicitly what assumptions, simplifications, and approximations are incorporated into the models used in the TSPA. The flow model defines the pathways for water flow in the EBS and specifies how the flow rate is computed in each pathway. Input to this model includes the seepage flux into a drift. The seepage flux is potentially split by the drip shield, with some (or all) of the flux being diverted by the drip shield and some passing through breaches in the drip shield that might result from corrosion or seismic damage. The flux through drip shield breaches is potentially split by the waste package, with some (or all) of the flux being diverted by the waste package and some passing through waste package breaches that might result from corrosion or seismic damage. Neither the drip shield nor the waste package survives an igneous intrusion, so the flux splitting submodel is not used in the igneous scenario class. The flow model is validated in an independent model validation technical review. The drip shield and waste package flux splitting algorithms are developed and validated using experimental data. The transport model considers advective transport and diffusive transport

The recent industrial EB applications in Japan

International Nuclear Information System (INIS)

Nakai, Koji; Kashiwagi, Masayuki; Mizusawa, Kenichi

1995-01-01

The conventional applications of electron beam processing such as, crosslinking of electric wire and cable insulations, polyethylene foam, and of rubber tire components have been the main part of the EB business for many years. New applications are continuing to appear, however, the growth of the new applications has been relatively slow. Nissin High-Voltage, as one of the worlds leading manufacturers of electron beam equipments, continues to develop and improve EB equipment to meet the requirements of these new applications. In this paper recent EB applications and its improvements are described. (author)

Using EB-QFD to achieve competitive advantages for world class manufacturing

Directory of Open Access Journals (Sweden)

Rahman Mostofi

2012-10-01

Full Text Available This paper introduces a tool named EB-QFD used for electronic business planning in strategic issues. Nowadays, the challenges of manufacturing sectors for achieving global competition will depend on their speed to change from domestic to world class manufacturing organizations, also the rapid global deployment of electronic business, information technology and their benefits have required managers to make decision, which look for a balance world class manufacturing factors with strategic business goals. To ensure that selected e-business strategies meet world class manufacturing requirements, organizations should simultaneously explore and communicate the relationship between world class manufacturing and electronic business. Electronic business planners can achieve competitive advantages through the implementation of an integration of quality function deployment (QFD with electronic business (EB called EB-QFD. This study is based on data collected from an Iranian auto parts manufacturing company and the implementation of EB-QFD. In this research, EB-QFD contains two parts named EB-WHATs as needs of Electronic Business and EB-HOWs as resources for EB-WHATs. Statistical analysis points that there are positive relationships between using EB-WHATs and EB-HOW and world class manufacturing factors as competitive advantages. We used electronic business systems for EB-WHATs and resource based view (RBV for EB-HOWs.

Creep properties of EB welded joint on Hastelloy X

International Nuclear Information System (INIS)

Arata, Yoshiaki; Susei, Shuzo; Shimizu, Shigeki; Satoh, Keisuke; Nagai, Hiroyoshi.

1980-01-01

In order to clarify the creep properties of EB welds on Hastelloy X which is one of the candidate alloys for components of VHTR, creep tests on EB weld metal and welded joint were carried out. The results were discussed in comparison with those of base metal and TIG welds. Further, EB welds were evaluated from the standpoint of high temperature structural design. The results obtained are summarized as follows. 1) Both creep rupture strengths of EB weld metal and EB welded joint are almost equal to that of base metal, but those of TIG welds are lower than base metal. As for the secondary creep rate, EB weld metal is higher and TIG weld metal is lower than base metal. As for the time to onset of tertiary creep, no remarkable difference among base metal, EB weld metal and TIG weld metal is observed. 2) In case of EB weld metal, although anisotropy is slightly observed, the ductility is same or more as compared with base metal. In case of TIG weld metal, on the contrary, anisotropy is not observed and the ductility is essentially low. 3) Such rupture morphology of EB weld metal as appears to have resulted from interconnection of voids which occurred at grain boundary is similar to base metal. In case of TIG weld metal, however, many cracks with sharp tips are observed at grain boundary, and the rupture appears to have occurred in brittle by propagation and connection of the cracks. 4) It can be said from the standpoint of high temperature structural design that EB welding is very suitable to welding for structure where creep effects are significant, because both of the creep ductility and the rupture strength are almost equal to those of base metal. (author)

Antiviral activity of the EB peptide against zoonotic poxviruses

Directory of Open Access Journals (Sweden)

Altmann Sharon E

2012-01-01

Full Text Available Abstract Background The EB peptide is a 20-mer that was previously shown to have broad spectrum in vitro activity against several unrelated viruses, including highly pathogenic avian influenza, herpes simplex virus type I, and vaccinia, the prototypic orthopoxvirus. To expand on this work, we evaluated EB for in vitro activity against the zoonotic orthopoxviruses cowpox and monkeypox and for in vivo activity in mice against vaccinia and cowpox. Findings In yield reduction assays, EB had an EC50 of 26.7 μM against cowpox and 4.4 μM against monkeypox. The EC50 for plaque reduction was 26.3 μM against cowpox and 48.6 μM against monkeypox. A scrambled peptide had no inhibitory activity against either virus. EB inhibited cowpox in vitro by disrupting virus entry, as evidenced by a reduction of the release of virus cores into the cytoplasm. Monkeypox was also inhibited in vitro by EB, but at the attachment stage of infection. EB showed protective activity in mice infected intranasally with vaccinia when co-administered with the virus, but had no effect when administered prophylactically one day prior to infection or therapeutically one day post-infection. EB had no in vivo activity against cowpox in mice. Conclusions While EB did demonstrate some in vivo efficacy against vaccinia in mice, the limited conditions under which it was effective against vaccinia and lack of activity against cowpox suggest EB may be more useful for studying orthopoxvirus entry and attachment in vitro than as a therapeutic against orthopoxviruses in vivo.

UV/EB curing in Australia

International Nuclear Information System (INIS)

Woods, R.; Garnett, J.; Loo Teck Ng

1999-01-01

Progress in LTV/EB curing is reviewed in Australia. Generally the technology is used by those industries where curing is well developed in Europe and North America, however the scale is an order of magnitude lower due to the smaller market size. The Asian economic crisis does not appear to have affected expansion of the technology in Australia. EB continues to be successfully used in the packaging and foam fields whilst in UV, security devices, particularly banknotes are steadily expanding especially in export markets have been studied

UV and EB radiation processing in developing countries

International Nuclear Information System (INIS)

Garnett, J.L.

1991-01-01

Ultraviolet and electron beams (EB) are to be considered as complementary technologies in the radiation processing field. In many countries, UV processing is used as the pathfinder for EB. In the developing countries the decision to adopt radiation processing techniques to choose between UV and EB will largely be determined by economics, the availability of the chemists and also skilled personnel to service both lines and equipment. (orig./A.B.)

Formation and hematopoietic differentiation of human embryoid bodies by suspension and hanging drop cultures.

Science.gov (United States)

Cerdan, Chantal; Hong, Seok Ho; Bhatia, Mickie

2007-10-01

The in vitro aggregation of human embryonic stem cells (hESCs) into clusters termed embryoid bodies (EBs) allows for the spontaneous differentiation of cells representing endoderm, mesoderm, and ectoderm lineages. This stochastic process results however, in the generation of low numbers of differentiated cells, and can be enhanced to some extent by the addition of exogenous growth factors or overexpression of regulatory genes. In the authors' laboratory, the use of hematopoietic cytokines in combination with the mesoderm inducer bone morphogenetic protein-4 (BMP-4) was able to generate up to 90% of CD45(+) hematopoietic cells with colony-forming unit (CFU) activity. This unit describes two protocols that have been successfully applied in the authors' laboratory for the generation of EBs in (1) suspension and (2) hanging drop (HD) cultures from enzymatically digested clumps of undifferentiated hESC colonies.

VEGF and IHH rescue definitive hematopoiesis in Gata-4 and Gata-6-deficient murine embryoid bodies.

Science.gov (United States)

Pierre, Monique; Yoshimoto, Momoko; Huang, Lan; Richardson, Matthew; Yoder, Mervin C

2009-09-01

Murine embryonic stem cells can be differentiated into embryoid bodies (EBs), which serve as an in vitro model recapitulating many aspects of embryonic yolk sac hematopoiesis. Differentiation of embryonic stem cells deficient in either Gata-4 or Gata-6 results in EBs with disrupted visceral endoderm (VE). While lack of VE has detrimental effects on hematopoiesis in vivo, it is unclear whether lack of VE affects hematopoiesis in EBs. Therefore, we compared Gata-4 null (G4N) and Gata-6 null (G6N) EBs with wild-type EBs to assess their ability to commit to hematopoietic cells. EB VE formation was examined using cell-sorting techniques and analysis visceral endoderm gene expression. Hematopoietic progenitor potential of EBs cultured under various conditions was assessed using colony-forming assays. Definitive erythroid, granulocyte-macrophage, and mixed colonies were significantly reduced in G4N and G6N EBs compared to wild-type EBs. Vascular endothelial growth factor (VEGF) expression and secretion were also reduced in both G4N and G6N EBs, consistent with VE serving as a site of VEGF production. Addition of exogenous VEGF(165), to EB cultures completely rescued definitive colony-forming cells in G4N and G6N EBs. This rescue response could be blocked by addition of soluble Flk-1 Fc to EB cultures. Similarly, addition of exogenous Indian hedgehog to EB cultures also recovers the diminishment in definitive hematopoiesis in a reversible manner. These results suggest that the absence of VE in G4N and G6N EBs does not prevent emergence of definitive progenitors from EBs. However, the decreased level of VEGF and Indian hedgehog production in VE devoid G4N and G6N EBs attenuates definitive hematopoietic progenitor cell expansion.

UV/EB curable psa's

International Nuclear Information System (INIS)

Glotfelter, C.A.

1995-01-01

The author describe both water-based and 100% solids UV/EB curable PSA's (Pressure Sensitive Adhesives) and their properties. A new acrylate monomer, ethoxylated nonyl phenol acrylate, has great utility in the formulation of water-based PSA's

EB application in pressure sensitive adhesives

International Nuclear Information System (INIS)

Hisashi Itoh; Ichiro Enomoto

1999-01-01

Two kinds of pressure sensitive adhesives (PSA's), that were formulations of radiation cross-linkable styrene-isoprene block copolymer (SIS) and complete hydrogenated aliphatic tackifying resin or non-hydrogenated, were prepared and the electron beam (EB) irradiation effect on these PSA performances such as peel strength against some kinds of adherends was studied. The results from measuring of PSA performance exhibit the close correlation between EB irradiation effect of these and the miscibility of the tackifying resin against SIS. Further it was clarified that PSA performance was influenced by the surface tension of adherends

Nanograined Net-Shaped Fabrication of Rhenium Components by EB-PVD

International Nuclear Information System (INIS)

Singh, Jogender; Wolfe, Douglas E.

2004-01-01

Cost-effective net-shaped forming components have brought considerable interest into DoD, NASA and DoE. Electron beam physical vapor deposition (EB-PVD) offers flexibility in forming net-shaped components with tailored microstructure and chemistry. High purity rhenium (Re) components including rhenium-coated graphite balls, Re- plates and tubes have been successfully manufactured by EB-PVD. EB-PVD Re components exhibited sub-micron and nano-sized grains with high hardness and strength as compared to CVD. It is estimated that the cost of Re components manufactured by EB-PVD would be less than the current CVD and powder-HIP Technologies

New surface modification method of bio-titanium alloy by EB polishing

International Nuclear Information System (INIS)

Okada, Akira; Uno, Yoshiyuki; Iio, Atsuo; Fujiwara, Kunihiko; Doi, Kenji

2008-01-01

A new surface modification for bio-titanium alloy products by electron beam (EB) polishing is proposed. In this EB polishing method, high energy density EB can be irradiated without concentrating the beam. Therefore, large-area EB with a maximum diameter of 60 mm can be used for instantaneously melting or evaporating metal surface. Experimental results made it clear that surface characteristics, such as repellency, corrosion resistance and coefficient of friction could be improved simultaneously with the surface smoothing in a few minutes under a proper condition. Therefore, EB polishing method has a possibility of high efficient surface smoothing and surface modification process for bio-titanium alloy. (author)

Reactive Transport and Coupled THM Processes in Engineering Barrier Systems (EBS)

International Nuclear Information System (INIS)

Steefel, Carl; Rutqvist, Jonny; Tsang, Chin-Fu; Liu, Hui-Hai; Sonnenthal, Eric; Houseworth, Jim; Birkholzer, Jens

2010-01-01

Geological repositories for disposal of high-level nuclear wastes generally rely on a multi-barrier system to isolate radioactive wastes from the biosphere. The multi-barrier system typically consists of a natural barrier system, including repository host rock and its surrounding subsurface environment, and an engineering barrier system (EBS). EBS represents the man-made, engineered materials placed within a repository, including the waste form, waste canisters, buffer materials, backfill and seals (OECD, 2003). EBS plays a significant role in the containment and long-term retardation of radionuclide release. EBS is involved in complex thermal, hydrogeological, mechanical, chemical and biological processes, such as heat release due to radionuclide decay, multiphase flow (including gas release due to canister corrosion), swelling of buffer materials, radionuclide diffusive transport, waste dissolution and chemical reactions. All these processes are related to each other. An in-depth understanding of these coupled processes is critical for the performance assessment (PA) for EBS and the entire repository. Within the EBS group of Used Fuel Disposition (UFD) Campaign, LBNL is currently focused on (1) thermal-hydraulic-mechanical-chemical (THMC) processes in buffer materials (bentonite) and (2) diffusive transport in EBS associated with clay host rock, with a long-term goal to develop a full understanding of (and needed modeling capabilities to simulate) impacts of coupled processes on radionuclide transport in different components of EBS, as well as the interaction between near-field host rock (e.g., clay) and EBS and how they effect radionuclide release. This final report documents the progress that LBNL has made in its focus areas. Specifically, Section 2 summarizes progress on literature review for THMC processes and reactive-diffusive radionuclide transport in bentonite. The literature review provides a picture of the state-of-the-art of the relevant research areas

Reactive Transport and Coupled THM Processes in Engineering Barrier Systems (EBS)

Energy Technology Data Exchange (ETDEWEB)

Steefel, Carl; Rutqvist, Jonny; Tsang, Chin-Fu; Liu, Hui-Hai; Sonnenthal, Eric; Houseworth, Jim; Birkholzer, Jens

2010-08-31

Geological repositories for disposal of high-level nuclear wastes generally rely on a multi-barrier system to isolate radioactive wastes from the biosphere. The multi-barrier system typically consists of a natural barrier system, including repository host rock and its surrounding subsurface environment, and an engineering barrier system (EBS). EBS represents the man-made, engineered materials placed within a repository, including the waste form, waste canisters, buffer materials, backfill and seals (OECD, 2003). EBS plays a significant role in the containment and long-term retardation of radionuclide release. EBS is involved in complex thermal, hydrogeological, mechanical, chemical and biological processes, such as heat release due to radionuclide decay, multiphase flow (including gas release due to canister corrosion), swelling of buffer materials, radionuclide diffusive transport, waste dissolution and chemical reactions. All these processes are related to each other. An in-depth understanding of these coupled processes is critical for the performance assessment (PA) for EBS and the entire repository. Within the EBS group of Used Fuel Disposition (UFD) Campaign, LBNL is currently focused on (1) thermal-hydraulic-mechanical-chemical (THMC) processes in buffer materials (bentonite) and (2) diffusive transport in EBS associated with clay host rock, with a long-term goal to develop a full understanding of (and needed modeling capabilities to simulate) impacts of coupled processes on radionuclide transport in different components of EBS, as well as the interaction between near-field host rock (e.g., clay) and EBS and how they effect radionuclide release. This final report documents the progress that LBNL has made in its focus areas. Specifically, Section 2 summarizes progress on literature review for THMC processes and reactive-diffusive radionuclide transport in bentonite. The literature review provides a picture of the state-of-the-art of the relevant research areas

A protocol describing the use of a recombinant protein-based, animal product-free medium (APEL) for human embryonic stem cell differentiation as spin embryoid bodies.

Science.gov (United States)

Ng, Elizabeth S; Davis, Richard; Stanley, Edouard G; Elefanty, Andrew G

2008-01-01

In order to promote the uniform and reproducible differentiation of human embryonic stem cells (HESCs) in response to exogenously added growth factors, we have developed a method (spin embryoid bodies (EBs)) that uses a recombinant protein-based, animal product-free medium in which HESCs are aggregated by centrifugation to form EBs. In this protocol we describe the formulation of this medium, denoted APEL (Albumin Polyvinylalcohol Essential Lipids), and its use in spin EB differentiation of HESCs. We also describe a more economical variant, BPEL (Bovine Serum Albumin (BSA) Polyvinylalchohol Essential Lipids), in which BSA replaces the recombinant human albumin. The integration of a medium that includes only defined and recombinant components with a defined number of cells to initiate EB formation results in a generally applicable, robust platform for growth factor-directed HESC differentiation.

Nuclear body formation and PML body remodeling by the human cytomegalovirus protein UL35

International Nuclear Information System (INIS)

Salsman, Jayme; Wang Xueqi; Frappier, Lori

2011-01-01

The human cytomegalovirus (HCMV) UL35 gene encodes two proteins, UL35 and UL35a. Expression of UL35 in transfected cells results in the formation of UL35 nuclear bodies that associate with promyelocytic leukemia (PML) protein. PML forms the basis for PML nuclear bodies that are important for suppressing viral lytic gene expression. Given the important relationship between PML and viral infection, we have further investigated the association of UL35 with PML bodies. We demonstrate that UL35 bodies form independently of PML and subsequently recruit PML, Sp100 and Daxx. In contrast, UL35a did not form bodies; however, it could bind UL35 and inhibit the formation of UL35 bodies. The HCMV tegument protein pp71 promoted the formation of UL35 bodies and the cytoplasmic localization of UL35a. Similarly, UL35a shifted pp71 to the cytoplasm. These results indicate that the interplay between UL35, UL35a and pp71 affects their subcellular localization and likely their functions throughout infection.

Effective data compaction algorithm for vector scan EB writing system

Science.gov (United States)

Ueki, Shinichi; Ashida, Isao; Kawahira, Hiroichi

2001-01-01

We have developed a new mask data compaction algorithm dedicated to vector scan electron beam (EB) writing systems for 0.13 μm device generation. Large mask data size has become a significant problem at mask data processing for which data compaction is an important technique. In our new mask data compaction, 'array' representation and 'cell' representation are used. The mask data format for the EB writing system with vector scan supports these representations. The array representation has a pitch and a number of repetitions in both X and Y direction. The cell representation has a definition of figure group and its reference. The new data compaction method has the following three steps. (1) Search arrays of figures by selecting pitches of array so that a number of figures are included. (2) Find out same arrays that have same repetitive pitch and number of figures. (3) Search cells of figures, where the figures in each cell take identical positional relationship. By this new method for the mask data of a 4M-DRAM block gate layer with peripheral circuits, 202 Mbytes without compaction was highly compacted to 6.7 Mbytes in 20 minutes on a 500 MHz PC.

Clearance of chlamydial elementary bodies from the conjunctival sac

International Nuclear Information System (INIS)

Taylor, H.R.; Velez, V.L.

1987-01-01

The rate of disappearance of inactivated Chlamydia trachomatis elementary body (EB) preparations from the conjunctival sac was studied in monkeys. Direct fluorescent antibody (DFA) cytology showed that the majority of EB had been cleared from the eye within 24 hr of the inoculation of 1 X 10(6) inactivated EB, although small numbers of EB could be detected for up to 144 hr. The rate of clearance in normal and ocular immune animals did not differ, and formalin-killed and UV-inactivated EBs disappeared at a comparable rate. These studies suggest that chlamydial EB are cleared relatively quickly from the eye and support the notion that EBs detected by DFA cytology indicate the presence of current infection

EB Frond wave energy converter - phase 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

The EB Frond project is a wave energy programme developed by The Engineering Business (EB) from an original idea at Lancaster University. The EB Frond is a wave generator with a collector vane on top of an arm that pivots near the seabed. Phase 1 of the project demonstrated the technical feasibility of the project and provided proof of concept. Phase 2 involved further assesment of the technical and commercial viability of the concept through the development of mathematical and physical modelling methods. The work involved small-scale (1/25th) testing in wave tanks at Newcastle and Lancaster Universities and the development, verification and validation of a time domain mathematical model. The decision by EB to put on hold its renewable generation programme meant that plans to test at an intermediate scale (1/16th), assess different survival strategies in extreme wave conditions, carry out site characterisation for full-scale systems and to produce a robust economic model were not fulfilled. However, the mathematical and physical modelling work was used to develop an economic model for the Frond system. This produced a predicted unit cost of electricity by a pre-commercial 5 MW demonstration farm of about 17 pence/kWh. The report discusses the small-scale testing, test results, mathematical modelling, analysis and interpretation, survivability, the economic model and the development route to full-scale production.

Current state of low energy EB devices and its application technology

International Nuclear Information System (INIS)

Kinoshita, Shinobu

2000-01-01

This paper introduced the current state of low energy type EB (electron beam) devices with an acceleration voltage of 300 kV or below and specific application examples. As for EB devices, it introduced the ultra-compact new EB device (microbeam LV), experimental devices, and the pilot/production devices which have been recently developed by the manufacturer to which the author belongs. As the applications of low energy EB devices, it specifically introduced curing, graft polymerization, crosslinking, and sterilization/disinfection with soft electrons: (1) examples of EB curing; antistatic agents in antibacterial/antifungal property imparting processing, hard coat, printing and topcoat, high gloss/pattern transfer processing, and metal vapor deposition film, (2) example of graft polymerization; barrier imparting films, and (3) examples of crosslinking; shrinking films/tubes and foamed sheets. (A.O.)

UV/EB curing market in Indonesia

International Nuclear Information System (INIS)

Hilmy, N.; Danu, S.

1999-01-01

The most application of UV curing of surface coating in Indonesia are on fancy plywood, furniture and wood flooring industry. Other application are on papers, printing ink/labelling, printed circuit board/PCB and dental materials. At present, application of EB curing coating is still in a pilot plant scale due to the high cost of production. Limited number of application of EB curing by using low energy electron beam machine are on wood panels, ceramics and marbles. This paper describes the market and the problem faced by the largest user of radiation curing systems such as the secondary process plywood, furniture and paper industries

In vivo kinetics of U4/U6.U5 tri-snRNP formation in Cajal bodies

Czech Academy of Sciences Publication Activity Database

Novotný, Ivan; Blažíková, Michaela; Staněk, David; Heřman, P.; Malínský, Jan

2011-01-01

Roč. 22, č. 4 (2011), s. 513-523 ISSN 1059-1524 R&D Projects: GA ČR GA204/07/0133; GA AV ČR KAN200520801 Institutional research plan: CEZ:AV0Z50520514; CEZ:AV0Z50390512; CEZ:AV0Z50390703 Keywords : small nuclear ribonucleoprotein * body components * dynamics Subject RIV: EB - Genetics ; Molecular Biology Impact factor : 4.942, year: 2011

Evaluation of the PetrifilmTM EB and TEMPO® EB systems with ISO 21528-2:2004 method for the count of Enterobacteriaceae in milk

Directory of Open Access Journals (Sweden)

Andréia Cirolini

2013-09-01

Full Text Available The development of alternative microbiological techniques is driven by the necessity to meet the current needs to deliver rapid results in the manufacturing process of foods, but it is important that these methods be evaluated for each application. The objective of the present study was to assess the PetrifilmTM EB and the TEMPO® EB systems with ISO 21528-2:2004 for the count of Enterobacteriaceae in pasteurized and UHT milk samples. We analyzed the microflora of 141 pasteurized milk samples, 15 samples of artificially contaminated pasteurized milk and 15 samples of artificially contaminated UHT milk. Investigation of the method PetrifilmTM EB and ISO 21528:2 regression analysis showed a high correlation in the samples, r = 0.90 for the microflora of pasteurized milk, r = 0.98 for artificially contaminated pasteurized milk and r = 0.99 for the artificially contaminated UHT milk. In evaluating the system TEMPO EB ® method and ISO 21528:2 correlation was also significant in the analyzed samples, with r = 0.86 for the microflora of pasteurized milk, r = 0.96 for artificially contaminated pasteurized milk and r = 0.99 for artificially contaminated UHT milk. No statistically significant differences were observed between the three methods conducted to analyze artificially contaminated pasteurized and UHT milk at three inoculum levels. In conclusion, the PetrifilmTM EB system and the TEMPO® EB system may be an alternative to the ISO 21528-2:2004 for the Enterobacteriaceae assay for milk as because of the ease-of-operation and the time reduction achieved for conducting the microbiological assay using these systems.

EB detoxification of liquid hazardous wastes

International Nuclear Information System (INIS)

Tata, A.; Giuliani, S.

1996-07-01

In the work, an engineering approach to technical solutions, considering accelerated electron beams as radiation source, is carried out, in order to allow and evaluate an effective recovery of drinking water from highly chemically polluted groundwaters. In connection with different engineering technical and economic parameters (suitable doses, EB-machine type, plant features, etc.) and with reference to 1-100 ton/hr contaminated stream flowrate range (2-50 kGy as considered absorbed dose range), a specifically developed computer code was run. Analysis results, based on investment and functioning cost figures evaluated with reference to industrial plant management scenarios, are treatment unit costs showing a noticeable economic attractiveness of radiation EB-technologies in the field of considered applications

Fruit body formation on silkworm by Cordyceps militaris

Science.gov (United States)

Injection inoculation protocols for fruit body formation of Cordyceps militaris were investigated to improve the incidence of infection in the silkworm species Bombyx mori. Injection, with suspensions of C. militaris hyphal bodies into living silkworm pupae, was used to test for fruit body productio...

Disposal systems evaluations and tool development : Engineered Barrier System (EBS) evaluation.

Energy Technology Data Exchange (ETDEWEB)

Rutqvist, Jonny (LBNL); Liu, Hui-Hai (LBNL); Steefel, Carl I. (LBNL); Serrano de Caro, M. A. (LLNL); Caporuscio, Florie Andre (LANL); Birkholzer, Jens T. (LBNL); Blink, James A. (LLNL); Sutton, Mark A. (LLNL); Xu, Hongwu (LANL); Buscheck, Thomas A. (LLNL); Levy, Schon S. (LANL); Tsang, Chin-Fu (LBNL); Sonnenthal, Eric (LBNL); Halsey, William G. (LLNL); Jove-Colon, Carlos F.; Wolery, Thomas J. (LLNL)

2011-01-01

Key components of the nuclear fuel cycle are short-term storage and long-term disposal of nuclear waste. The latter encompasses the immobilization of used nuclear fuel (UNF) and radioactive waste streams generated by various phases of the nuclear fuel cycle, and the safe and permanent disposition of these waste forms in geological repository environments. The engineered barrier system (EBS) plays a very important role in the long-term isolation of nuclear waste in geological repository environments. EBS concepts and their interactions with the natural barrier are inherently important to the long-term performance assessment of the safety case where nuclear waste disposition needs to be evaluated for time periods of up to one million years. Making the safety case needed in the decision-making process for the recommendation and the eventual embracement of a disposal system concept requires a multi-faceted integration of knowledge and evidence-gathering to demonstrate the required confidence level in a deep geological disposal site and to evaluate long-term repository performance. The focus of this report is the following: (1) Evaluation of EBS in long-term disposal systems in deep geologic environments with emphasis on the multi-barrier concept; (2) Evaluation of key parameters in the characterization of EBS performance; (3) Identification of key knowledge gaps and uncertainties; and (4) Evaluation of tools and modeling approaches for EBS processes and performance. The above topics will be evaluated through the analysis of the following: (1) Overview of EBS concepts for various NW disposal systems; (2) Natural and man-made analogs, room chemistry, hydrochemistry of deep subsurface environments, and EBS material stability in near-field environments; (3) Reactive Transport and Coupled Thermal-Hydrological-Mechanical-Chemical (THMC) processes in EBS; and (4) Thermal analysis toolkit, metallic barrier degradation mode survey, and development of a Disposal Systems

Disposal systems evaluations and tool development: Engineered Barrier System (EBS) evaluation

International Nuclear Information System (INIS)

Rutqvist, Jonny; Liu, Hui-Hai; Steefel, Carl I.; Serrano de Caro, M.A.; Caporuscio, Florie Andre; Birkholzer, Jens T.; Blink, James A.; Sutton, Mark A.; Xu, Hongwu; Buscheck, Thomas A.; Levy, Schon S.; Tsang, Chin-Fu; Sonnenthal, Eric; Halsey, William G.; Jove-Colon, Carlos F.; Wolery, Thomas J.

2011-01-01

Key components of the nuclear fuel cycle are short-term storage and long-term disposal of nuclear waste. The latter encompasses the immobilization of used nuclear fuel (UNF) and radioactive waste streams generated by various phases of the nuclear fuel cycle, and the safe and permanent disposition of these waste forms in geological repository environments. The engineered barrier system (EBS) plays a very important role in the long-term isolation of nuclear waste in geological repository environments. EBS concepts and their interactions with the natural barrier are inherently important to the long-term performance assessment of the safety case where nuclear waste disposition needs to be evaluated for time periods of up to one million years. Making the safety case needed in the decision-making process for the recommendation and the eventual embracement of a disposal system concept requires a multi-faceted integration of knowledge and evidence-gathering to demonstrate the required confidence level in a deep geological disposal site and to evaluate long-term repository performance. The focus of this report is the following: (1) Evaluation of EBS in long-term disposal systems in deep geologic environments with emphasis on the multi-barrier concept; (2) Evaluation of key parameters in the characterization of EBS performance; (3) Identification of key knowledge gaps and uncertainties; and (4) Evaluation of tools and modeling approaches for EBS processes and performance. The above topics will be evaluated through the analysis of the following: (1) Overview of EBS concepts for various NW disposal systems; (2) Natural and man-made analogs, room chemistry, hydrochemistry of deep subsurface environments, and EBS material stability in near-field environments; (3) Reactive Transport and Coupled Thermal-Hydrological-Mechanical-Chemical (THMC) processes in EBS; and (4) Thermal analysis toolkit, metallic barrier degradation mode survey, and development of a Disposal Systems

RPC industries - UV and EB equipment manufacturers

International Nuclear Information System (INIS)

Rodrigues, A.M.

1987-01-01

RPC Industries has been manufacturing electron beam and ultraviolet equipment for the industrial processing of materials for more than 15 years. RPC maintains its headquarters and electron processor manufacturing plant in Hayward, California. UV equipment is made in the company's plant near Chicago. Sales offices are maintained in New York, Illinois, and California in the USA, and in Germany, Japan, Australia, Italy, Israel, and Sweden. Complete testing and pilot facilities are available in Hayward (EB) and near Chicago (UV). Described below are the basic system components, applications and advantages of RPC's UV and EB systems. (orig.)

Application of calorimeters for 5 MeV EB and bremsstrahlung dosimetry

DEFF Research Database (Denmark)

Sato, T.; Takahashi, T.; Saito, T.

1993-01-01

Graphite and water calorimeters, which were developed for use a 10 MeV electron beams (EB) at Riso National Laboratory, were used for process validation and routine dosimeter calibration at a 5 MeV EB. Water calorimeters were used for reference measurements for 5 MeV EB, the response was found...... to be directly proportional to the beam current and the variation among three water calorimeters was less than +/- 2 % in the range of 10 to 40 kGy. CTA, PMMA, RCD dosimeters were calibrated by irradiating the dosimeters and water calorimeters Simultaneously. The water calorimeter was proved to be an useful tool...... at 5 MeV EB. Graphite calorimeters gave reproducible readings within 3.3 % relative errors (95 % confidence level) for X-ray measurement....

Application of calorimeters for 5 MeV EB and bremsstrahlung dosimetry

International Nuclear Information System (INIS)

Sato, Toshio; Takahashi, Toru; Saito, Toshio; Takehisa, Masaaki; Miller, A.

1993-01-01

Graphite and water calorimeters, which were developed for use with 10 MeV electron beams (EB) at Riso National Laboratory, were used for process validation and routine dosimeter calibration at a 5 MeV EB. Water calorimeters were used for reference measurements for 5 MeV EB, the response was found to be directly proportional to the beam current and the variation among three water calorimeters was less than ± 2% in the range of 10 to 40 kGy. CTA PMMA RCD dosimeters were calibrated by irradiating the dosimeters and water calorimeters simultaneously. The water calorimeter was proved to be an useful tool at 5 MeV EB. Graphite calorimeters gave reproducible readings within 3.3 % relative errors (95% confidence level) for X-ray measurement. (Author)

EB-welding of the copper canister for the nuclear waste disposal. Final report of the development programme 1994-1997

International Nuclear Information System (INIS)

Aalto, H.

1998-10-01

During 1994-1997 Posiva Oy and Outokumpu Poricopper Oy had a joint project Development of EB-welding method for massive copper canister manufacturing. The project was part of the national technology program 'Weld 2000' and it was supported financially by Technology Development Centre (TEKES). The spent fuel from Finnish nuclear reactors is planned to be encapsulated in thick-walled copper canisters and placed deep into the bedrock. The thick copper layer of the canister provides a long time corrosion resistance and prevents deposited nuclear fuel from contact with water. The quality requirements of the copper components are high because of the designed long lifetime of the canister. The EB-welding technology has proved to be applicable method for the production of the copper canisters and the EB-welding technique is needed at least when the lids of the copper canister will be closed. There are a number of parameters in EB-welding which affect weldability. However, the effect of the welding parameters and their optimization has not been extensively studied in welding of thick copper sections using conventional high vacuum EB-welding. One aim of this development work was to extensively study effect of welding parameters on weld quality. The final objective was to minimise welding defects in the main weld and optimize slope out procedure in thick copper EB-welding. Welding of 50 mm thick copper sections was optimized using vertical and horizontal EB-welding techniques. As a result two full scale copper lids were welded to a short cylinder successfully. The resulting weld quality with optimised welding parameters was reasonable good. The optimised welding parameters for horizontal and vertical beam can be applied to the longitudinal body welds of the canister. The optimal slope out procedure for the lid closure needs some additional development work. In addition of extensive EB-welding program ultrasonic inspection and creep strength of the weld were studied. According

EB-welding of the copper canister for the nuclear waste disposal. Final report of the development programme 1994-1997

Energy Technology Data Exchange (ETDEWEB)

Aalto, H. [Outokumpu Oy Poricopper, Pori (Finland)

1998-10-01

During 1994-1997 Posiva Oy and Outokumpu Poricopper Oy had a joint project Development of EB-welding method for massive copper canister manufacturing. The project was part of the national technology program `Weld 2000` and it was supported financially by Technology Development Centre (TEKES). The spent fuel from Finnish nuclear reactors is planned to be encapsulated in thick-walled copper canisters and placed deep into the bedrock. The thick copper layer of the canister provides a long time corrosion resistance and prevents deposited nuclear fuel from contact with water. The quality requirements of the copper components are high because of the designed long lifetime of the canister. The EB-welding technology has proved to be applicable method for the production of the copper canisters and the EB-welding technique is needed at least when the lids of the copper canister will be closed. There are a number of parameters in EB-welding which affect weldability. However, the effect of the welding parameters and their optimization has not been extensively studied in welding of thick copper sections using conventional high vacuum EB-welding. One aim of this development work was to extensively study effect of welding parameters on weld quality. The final objective was to minimise welding defects in the main weld and optimize slope out procedure in thick copper EB-welding. Welding of 50 mm thick copper sections was optimized using vertical and horizontal EB-welding techniques. As a result two full scale copper lids were welded to a short cylinder successfully. The resulting weld quality with optimised welding parameters was reasonable good. The optimised welding parameters for horizontal and vertical beam can be applied to the longitudinal body welds of the canister. The optimal slope out procedure for the lid closure needs some additional development work. In addition of extensive EB-welding program ultrasonic inspection and creep strength of the weld were studied. According

EB treatment of carbon nanotube-reinforced polymer composites

International Nuclear Information System (INIS)

Szebenyi, G.; Romhany, G.; Czvikovszky, T.; Vajna, B.

2011-01-01

Complete text of publication follows. A small amount - less than 0.5% - carbon nanotube reinforcement may improve significantly the mechanical properties of epoxy based composite materials. The basic technical problem is on one side the dispersion of the nanotubes into the viscous matrix resin. Namely the fine, powder-like - less than 100 nanometer diameter - nanotubes are prone to form aggregates. On the other side, the good connection between the nanofiber and matrix, - which is determining the success of the reinforcement, - requires some efficient adhesion promoting treatment. After an elaborate masterbatch mixing technology we applied Electron Beam treatment of epoxy-matrix polymer composites containing carbon nanotubes in presence of vinylester resins. The Raman spectra of vinylester-epoxy mixtures treated by an 8 MeV EB showed the advantage of the electron treatment. Even in the case of partially immiscible epoxy and vinylester resins, the anchorage of carbon nanotubes reflects improvement if a reasonable 25 kGy EB dose is applied. Atomic Force Microscopy as well as mechanical tests on flexural and impact properties confirm the benefits of EB treatment. Simultaneous application of multiwall carbon nanotubes and 'conventional' carbon fibers as reinforcement in vinylester modified epoxies results in new types of hybrid nanocomposites as engineering materials. The bending- and interlaminar properties of such hybrid systems showed the beneficial effect of the EB treatment. Acknowledgement: This work has been supported by the New Hungary Development Plan (Project ID: TAMOP-4.2.1/B-09/1/KMR-2010-0002).

TIP maker and TIP marker; EB1 as a master controller of microtubule plus ends.

Science.gov (United States)

Vaughan, Kevin T

2005-10-24

The EB1 protein is a member of the exciting and enigmatic family of microtubule (MT) tip-tracking proteins. EB1 acts as an exquisite marker of dynamic MT plus ends in some cases, whereas in others EB1 is thought to directly dictate the behavior of the plus ends. How EB1 differentiates between these two roles remains unclear; however, a growing list of interactions between EB1 and other MT binding proteins suggests there may be a single mechanism. Adding another layer of complexity to these interactions, two studies published in this issue implicate EB1 in cross-talk between mitotic MTs and between MTs and actin filaments (Goshima et al., p. 229; Wu et al., p. 201). These results raise the possibility that EB1 is a central player in MT-based transport, and that the activity of MT-binding proteins depends on their ability or inability to interact with EB1.

Single photon detection and localization accuracy with an ebCMOS camera

Energy Technology Data Exchange (ETDEWEB)

Cajgfinger, T. [CNRS/IN2P3, Institut de Physique Nucléaire de Lyon, Villeurbanne F-69622 (France); Dominjon, A., E-mail: agnes.dominjon@nao.ac.jp [Université de Lyon, Université de Lyon 1, Lyon 69003 France. (France); Barbier, R. [CNRS/IN2P3, Institut de Physique Nucléaire de Lyon, Villeurbanne F-69622 (France); Université de Lyon, Université de Lyon 1, Lyon 69003 France. (France)

2015-07-01

The CMOS sensor technologies evolve very fast and offer today very promising solutions to existing issues facing by imaging camera systems. CMOS sensors are very attractive for fast and sensitive imaging thanks to their low pixel noise (1e-) and their possibility of backside illumination. The ebCMOS group of IPNL has produced a camera system dedicated to Low Light Level detection and based on a 640 kPixels ebCMOS with its acquisition system. After reminding the principle of detection of an ebCMOS and the characteristics of our prototype, we confront our camera to other imaging systems. We compare the identification efficiency and the localization accuracy of a point source by four different photo-detection devices: the scientific CMOS (sCMOS), the Charge Coupled Device (CDD), the Electron Multiplying CCD (emCCD) and the Electron Bombarded CMOS (ebCMOS). Our ebCMOS camera is able to identify a single photon source in less than 10 ms with a localization accuracy better than 1 µm. We report as well efficiency measurement and the false positive identification of the ebCMOS camera by identifying more than hundreds of single photon sources in parallel. About 700 spots are identified with a detection efficiency higher than 90% and a false positive percentage lower than 5. With these measurements, we show that our target tracking algorithm can be implemented in real time at 500 frames per second under a photon flux of the order of 8000 photons per frame. These results demonstrate that the ebCMOS camera concept with its single photon detection and target tracking algorithm is one of the best devices for low light and fast applications such as bioluminescence imaging, quantum dots tracking or adaptive optics.

Elemental imaging of organic matter and associated metals in ore deposits using micro PIXE and micro-EBS

Energy Technology Data Exchange (ETDEWEB)

Fuchs, S., E-mail: fuchs@geomin.eu [Department of Earth and Planetary Science, McGill University, 3450 University Street, Montreal H3A 0E8 (Canada); Przybylowicz, W.J., E-mail: przybylowicz@tlabs.ac.za [Materials Research Department, iThemba LABS, National Research Foundation, P.O. Box 722, Somerset West 7129 (South Africa); AGH University of Science and Technology, Faculty of Physics and Applied Computer Science, Al. A. Mickiewicza 30, 30-059 Krakow (Poland); Williams-Jones, A.E., E-mail: anthony.williams-jones@mcgill.ca [Department of Earth and Planetary Science, McGill University, 3450 University Street, Montreal H3A 0E8 (Canada)

2014-01-01

Micro-PIXE and micro-EBS analyses were carried out on samples from the Au–U-bearing Carbon Leader Reef of the Witwatersrand in South Africa to investigate the role of organic matter in the formation of this deposit. Micro-PIXE and Micro-EBS shows a very complex metal distribution within the bitumen nodules and their interstitial spaces. The style of the gold distribution and its association with epigenetic minerals (REE phosphates, phyllosilicates) indicates that all observed gold migrated in aqueous solution and precipitated by reduction on the surfaces of the bitumen nodules. Uraninite occurrences are confined to the bitumen nodules, which supports the argument of a uraninite paleo-placer; however the pervasive distribution of uranium also supports the argument that uraninite is derived from organo-metallic complexes. This study shows that micro-PIXE is a powerful tool to characterize metals associated with hydrocarbons. However, the organic matrix, the complexity of the obtained spectra and the small size of the minerals have significant influence on the reliability of the quantitative data. Due to highly variable amounts of heavy metals (U, Au, Pb) the obtained micro-EBS results are of questionable quality.

Y-27632 enhances differentiation of blastocyst like cystic human embryoid bodies to endocrinologically active trophoblast cells on a biomimetic platform

Directory of Open Access Journals (Sweden)

Totey Satish M

2009-09-01

Full Text Available Abstract Trophoblast differentiation and formation of the placenta are important events linked to post-implantation embryonic development. Models mimicking the biology of trophoblast differentiation in a post-implantation maternal microenvironment are needed for understanding disorders like placental-ischemia or for applications in drug-screening, and would help in overcoming the ethical impasse on using human embryos for such research. Here we attempt to create such a model by using embryoid bodies (EBs and a biomimetic platform composed of a bilayer of fibronectin and gelatin on top of low-melting agarose. Using this model we test the hypothesis that cystic-EBs (day 30 that resemble blastocysts morphologically, are better sources as compared to noncytic EBs (day 10, for functional trophoblast differentiation; and that the Rho kinases inhibitor Y27632 can enhance this differentiation. Non/cytic EBs with/out Y27632 were grown on this platform for 28 days, and screened from secretion and expression of trophoblast and other lineage markers using ECLIA, RT-PCR, and Immunofluorescence. All EBs attached on this surface and rapidly proliferated into hCG and progesterone (P2 secreting functional trophoblast cells. However, the cells derived from cytic-EBs and cytic-EBs+ Y27632 showed the maximum secretion of these hormones and expressed IGF2, supporting our hypothesis. Also Y27632 reduced extraembryonic endoderm and trophoblast lineage differentiation from early noncystic-EBs, whereas, it specifically enhanced the induction of trophoblast and multinucleated syncitiotrophoblast differentiation from late cystic-EBs. In vivo trophoblast differentiation can be replicated in fibronectin based biomaterials, using cytic-EBs and by maneuvering the Rho-ROCK pathways. Response of EBs to a compound may vary temporally, and determination of their right stage is crucial for applications in directed-differentiation or drug-screening.

The chemistry of UV and EB radiation curing

International Nuclear Information System (INIS)

Garnett, J.L.

1987-01-01

The application of photopolymerisation (UV) and electron beam (EB) technologies in radiation rapid cure (RRC) processing is discussed. The chemistry associated with such reactions and the mechanisms of the processes are treated. The occurrence of concurrent grafting to substrate with radiation curing of film is shown to be an advantage in enhancing the properties of certain finished products. The parameters influencing the optimum grafting yield in such RRC processes are discussed. In many applications, the chemistry of the process combined with the machine, expecially for EB, is shown a so-called ''turn-key'' operation. (author)

Risk factors for granuloma formation in children induced by tracheobronchial foreign bodies.

Science.gov (United States)

Huang, Zhenghua; Zhou, Ai; Zhang, Jianya; Xie, Lisheng; Li, Qi

2015-12-01

The aim of this study was to analyze the risk factors for granuloma formation caused by plant-based tracheobronchial foreign bodies in children, and investigate the underlying pathogenesis. In this retrospective analysis of 153 cases with tracheobronchial foreign bodies (peanuts and watermelon seeds), 35 cases of granuloma formation as granulation group (G), and 118 cases of no granuloma formation as non-granulation group (NG) were studied. Clinical data pertaining to sex (S), age (A), foreign body surface smoothness (SF), foreign body shape (SH), foreign body oil release state (O), the location of foreign bodies (L), and foreign body retention time (T) were collected for statistical analysis. Univariate analysis showed no significant difference between the two groups (G and NG) with respect to S, A, SH and L. Significant factors based on univariate analysis included SF, O and T. Multivariate logistic regression analysis revealed that SF and T were independent risk factors associated with development of granuloma. SF, O and T had relationship with the granuloma formation. Local trauma caused by an irregular and sharp foreign body, and extended period of time represent the main factors causing granuloma formation. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

The French methodology for EBS confirmation and demonstration

International Nuclear Information System (INIS)

Plas, F.; Voinis, S.; Mayer, S.

2007-01-01

The December 30, 1991 French Waste Act entrusted ANDRA, the French national agency for radioactive waste management, with the task of assessing the feasibility of deep geological disposal of high- and medium-level long-lived waste (HLW and ILW, respectively C-waste and B-waste types in French) plus spent fuel (CU in French). In that context, the 'Dossier 2005 Argile' submitted by ANDRA presents the feasibility assessment - with regard to the technical capacity to accommodate all wastes, to reversibility, and to safety - of a radioactive waste disposal in a clay formation studied at the Meuse/Haute-Marne URL. This report was built upon an iterative approach between site characterisation, design, modelling, phenomenological analysis and safety analysis, in which two principles always guided the elaboration of the safety case: the principle of robustness - repository components must maintain their functionality given reasonable solicitations, taking into account uncertainties on the nature and level of these solicitations; and the principle of demonstrability - safety must be verified without requiring complex demonstrations, and based on multiple lines of evidence/argument (numerical simulation, qualitative arguments such as use of natural analogues, experiments and technological demonstrators). In that respect, the EBS definition, demonstration and confirmation of design is a part of the overall safety case. The 'Dossier 2005 Argile' was submitted to three independent peer reviews. The aim. of this article is to present the methodology that ANDRA implemented in the context of 'Dossier 2005 Argile' for defining, demonstrating and confirming the EBS design as well as the future programme with respect with the new Act of 28 June 2006. (author)

End-Binding Protein 1 (EB1) Up-regulation is an Early Event in Colorectal Carcinogenesis

Science.gov (United States)

Stypula-Cyrus, Yolanda; Mutyal, Nikhil N.; Cruz, Mart Angelo Dela; Kunte, Dhananjay P.; Radosevich, Andrew J.; Wali, Ramesh; Roy, Hemant K.; Backman, Vadim

2014-01-01

End-binding protein (EB1) is a microtubule protein that binds to the tumor suppressor adenomatous polyposis coli (APC). While EB1 is implicated as a potential oncogene, its role in cancer progression is unknown. Therefore, we analyzed EB1/APC expression at the earliest stages of colorectal carcinogenesis and in the uninvolved mucosa ("field effect") of human and animal tissue. We also performed siRNA-knockdown in colon cancer cell lines. EB1 is up-regulated in early and field carcinogenesis in the colon, and the cellular/nano-architectural effect of EB1 knockdown depended on the genetic context. Thus, dysregulation of EB1 is an important early event in colon carcinogenesis. PMID:24492008

E.B. White: Aspects of Style.

Science.gov (United States)

Neumeyer, Peter F.

1987-01-01

Assesses the writing style of a famous author of children's books, concluding that E.B. White's informal tone uses anaphora, simple sentences, doubling and redundancy, and mixes colloquial with standard English. Provides examples of his style, from 10 years old to maturity. (NKA)

Safety, Pharmacokinetics and Dosimetry of a Long-Acting Radiolabeled Somatostatin Analogue 177Lu-DOTA-EB-TATE in Patients with Advanced Metastatic Neuroendocrine Tumors.

Science.gov (United States)

Zhang, Jingjing; Wang, Hao; Jacobson Weiss, Orit; Cheng, Yuejuan; Niu, Gang; Li, Fang; Bai, Chunmei; Zhu, Zhaohui; Chen, Xiaoyuan

2018-04-13

Radiolabeled somatostatin analogue therapy has become an established treatment method for patients with well to moderately differentiated unresectable or metastatic neuroendocrine tumors (NETs). The most frequently used somatostatin analogues in clinical practice are octreotide and octreotate. However, both peptides showed suboptimal retention within tumors. The aim of this first-in-human study is to explore the safety and dosimetry of a long-acting radiolabeled somatostatin analogue, lutetium-177-1, 4, 7, 10-tetra-azacyclododecane-1, 4, 7, 10-tetraacetic acid-Evans blue-octreotate ( 177 Lu-DOTA-EB-TATE). Methods: Eight patients (6 males and 2 females; age range, 27-61 y) with advanced metastatic neuroendocrine tumors were recruited. Five patients received a single dose 0.35-0.70 GBq (9.5-18.9 mCi) of 177 Lu-DOTA-EB-TATE and underwent serial whole body planar and single-photon emission computed tomography-computed tomography (SPECT-CT) scans at 2, 24, 72, 120 and 168 h after injection. The other 3 patients received intravenous injection of 0.28-0.41 GBq (7.5-11.1 mCi) of 177 Lu-DOTATATE for the same imaging acquisition procedures at 1, 3, 4, 24 and 72 h after injection. The dosimetry was calculated using the OLINDA/EXM 1.1 software. Results: Administration of 177 Lu-DOTA-EB-TATE was well tolerated, with no adverse symptoms being noticed or reported in any of the patients. Compared with 177 Lu-DOTATATE, 177 Lu-DOTA-EB-TATE showed extended circulation in the blood and achieved 7.9-fold increase of tumor dose delivery. The total body effective doses were 0.205 ± 0.161 mSv/MBq for 177 Lu-DOTA-EB-TATE and 0.174 ± 0.072 mSv/MBq for 177 Lu-DOTATATE. Significant dose delivery increases to the kidneys and bone marrow were also observed in patients receiving 177 Lu-DOTA-EB-TATE than those receiving 177 Lu-DOTATATE (3.2 and 18.2-fold, respectively). Conclusion: By introducing an albumin binding moiety, 177 Lu-DOTA-EB-TATE showed remarkably higher uptake and retention in NET

Chronic Ulceration and Sinus Formation due to Foreign Body

DEFF Research Database (Denmark)

Hansen, Karin Birgitte; Gottrup, Finn

2015-01-01

generated from a foreign body reaction. The case report shows that this condition is often overlooked and even using advanced equipment, it is difficult to diagnose. The only solution is to diagnose and remove the triggering cause. Fistulography and ultrasound scanning seem to be the optimal diagnostic tool......Foreign bodies like residues of suture or mesh may lead to a foreign body reaction, cavity formation and continuous secretion and perhaps ulceration. We present a more than 9 years long medical record of a 49 year old man after a simple surgical procedure. The background was a sinus formation...... in these cases. The knowledge of the foreign body reaction in tissue continuously needs to be reestablished in the health care system especially in areas, where implantation of foreign material is used....

EB and EUV lithography using inedible cellulose-based biomass resist material

Science.gov (United States)

Takei, Satoshi; Hanabata, Makoto; Oshima, Akihiro; Kashiwakura, Miki; Kozawa, Takahiro; Tagawa, Seiichi

2016-03-01

The validity of our approach of inedible cellulose-based resist material derived from woody biomass has been confirmed experimentally for the use of pure water in organic solvent-free water spin-coating and tetramethylammonium hydroxide(TMAH)-free water-developable techniques of eco-conscious electron beam (EB) and extreme-ultraviolet (EUV) lithography. The water developable, non-chemically amplified, high sensitive, and negative tone resist material in EB and EUV lithography was developed for environmental affair, safety, easiness of handling, and health of the working people. The inedible cellulose-based biomass resist material was developed by replacing the hydroxyl groups in the beta-linked disaccharides with EB and EUV sensitive groups. The 50-100 nm line and space width, and little footing profiles of cellulose-based biomass resist material on hardmask and layer were resolved at the doses of 10-30 μC/cm2. The eco-conscious lithography techniques was referred to as green EB and EUV lithography using inedible cellulose-based biomass resist material.

RNA Sequencing Reveals the Alteration of the Expression of Novel Genes in Ethanol-Treated Embryoid Bodies.

Science.gov (United States)

Mandal, Chanchal; Kim, Sun Hwa; Chai, Jin Choul; Oh, Seon Mi; Lee, Young Seek; Jung, Kyoung Hwa; Chai, Young Gyu

2016-01-01

Fetal alcohol spectrum disorder is a collective term representing fetal abnormalities associated with maternal alcohol consumption. Prenatal alcohol exposure and related anomalies are well characterized, but the molecular mechanism behind this phenomenon is not well characterized. In this present study, our aim is to profile important genes that regulate cellular development during fetal development. Human embryonic carcinoma cells (NCCIT) are cultured to form embryoid bodies and then treated in the presence and absence of ethanol (50 mM). We employed RNA sequencing to profile differentially expressed genes in the ethanol-treated embryoid bodies from NCCIT vs. EB, NCCIT vs. EB+EtOH and EB vs. EB+EtOH data sets. A total of 632, 205 and 517 differentially expressed genes were identified from NCCIT vs. EB, NCCIT vs. EB+EtOH and EB vs. EB+EtOH, respectively. Functional annotation using bioinformatics tools reveal significant enrichment of differential cellular development and developmental disorders. Furthermore, a group of 42, 15 and 35 transcription factor-encoding genes are screened from all of the differentially expressed genes obtained from NCCIT vs. EB, NCCIT vs. EB+EtOH and EB vs. EB+EtOH, respectively. We validated relative gene expression levels of several transcription factors from these lists by quantitative real-time PCR. We hope that our study substantially contributes to the understanding of the molecular mechanism underlying the pathology of alcohol-mediated anomalies and ease further research.

Main studies results for introduction of EB machine to Vietnam and for its application

International Nuclear Information System (INIS)

Tran, Khac An; Nguyen, Quoc Hien; Le, Hai

2004-01-01

Upon the national program on utilization of EB machine for research and development purposes and the FNCA project on application of electron accelerator, as a counterpart the Research and Development Center for Radiation Technology (VINAGAMMA) is preparing technical, manpower and financial conditions for introduction of an EB machine for R and D purposes. The paper offers main studied results in the field of Radiation Processing aimed at putting applications of EB technology into Vietnam and studies on selection of EB machine for R and D purposes in Vietnam. (author)

Two clusters of GABAergic ellipsoid body neurons modulate olfactory labile memory in Drosophila.

Science.gov (United States)

Zhang, Zhiping; Li, Xiaoting; Guo, Jing; Li, Yan; Guo, Aike

2013-03-20

In Drosophila, aversive olfactory memory is believed to be stored in a prominent brain structure, the mushroom body (MB), and two pairs of MB intrinsic neurons, the dorsal paired medial (DPM) and the anterior paired lateral (APL) neurons, are found to regulate the consolidation of middle-term memory (MTM). Here we report that another prominent brain structure, the ellipsoid body (EB), is also involved in the modulation of olfactory MTM. Activating EB R2/R4m neurons does not affect the learning index, but specifically eliminates anesthesia-sensitive memory (ASM), the labile component of olfactory MTM. We further demonstrate that approximately two-thirds of these EB neurons are GABAergic and are responsible for the suppression of ASM. Using GRASP (GFP reconstitution across synaptic partners), we reveal potential synaptic connections between the EB and MB in regions covering both the presynaptic and postsynaptic sites of EB neurons, suggesting the presence of bidirectional connections between these two important brain structures. These findings suggest the existence of direct connections between the MB and EB, and provide new insights into the neural circuit basis for olfactory labile memory in Drosophila.

Evaluation of interfacial mechanical properties under shear loading in EB-PVD TBCs by the pushout method

Energy Technology Data Exchange (ETDEWEB)

Kim, Sang-Seok [Research Center for Advanced Science and Technology, University of Tokyo, Tokyo 153-8904 (Japan); Liu Yufu [Research Center for Advanced Science and Technology, University of Tokyo, Tokyo 153-8904 (Japan); Kagawa, Yutaka [Research Center for Advanced Science and Technology, University of Tokyo, Tokyo 153-8904 (Japan)]. E-mail: kagawa@iis.u-tokyo.ac.jp

2007-06-15

A new simple pushout technique for evaluation of interfacial shear mechanical properties in thermal barrier coatings has been developed. The technique is similar to the pushout test of fiber-reinforced ceramics, except for the specimen shape and support method. The technique has been applied to evaluation of interfacial delamination toughness, {gamma} {sub i}, of the electron beam physical vapor deposition (EB-PVD) ZrO{sub 2} thermal barrier coating (TBC) system. The change of {gamma} {sub i} in the EB-PVD system with thermal exposure is measured and discussed in terms of microstructural change and delamination crack path. The measured delamination toughness varied from {gamma} {sub i} = 10 to 115 J/m{sup 2}. The delamination path and TGO growth were found to be closely related. The delamination toughness significantly decreases due to the formation and growth of a spinel phase in the TGO layer. The relation between delamination toughness and delamination behavior is discussed.

THE CONCEPT OF INTEGRATED ENGINEERING AND BUSINESS (EB EDUCATION SYSTEM

Directory of Open Access Journals (Sweden)

Michał Charlak

2013-12-01

Full Text Available In our approach to engineering and business education system an engineer is a man working as creator and user of technical products. We stress that the process of understanding and gaining knowledge of technical reality and creativity of engineers are the essential for EB concept . Next, we describe briefly three perspectives for building the system of innovative product origination as a basis for EB system: 1 designer’s perspective; 2 business perspective. 3 consumer perspective.

Post-irradiation mechanical tests on F82H EB and TIG welds

International Nuclear Information System (INIS)

Rensman, J.; Osch, E.V. van; Horsten, M.G.; D'Hulst, D.S.

2000-01-01

The irradiation behaviour of electron beam (EB) and tungsten inert gas (TIG) welded joints of the reduced-activation martensitic steel IEA heat F82H-mod. was investigated by neutron irradiation experiments in the high flux reactor (HFR) in Petten. Mechanical test specimens, such as tensile specimens and KLST-type Charpy impact specimens, were neutron irradiated up to a dose level of 2-3 dpa at a temperature of 300 deg. C in the HFR reactor in Petten. The tensile results for TIG and EB welds are as expected with practically no strain hardening capacity left. Considering impact properties, there is a large variation in impact properties for the TIG weld. The irradiation tends to shift the DBTT of particularly the EB welds to very high values, some cases even above +250 deg. C. PWHT of EB-welded material gives a significant improvement of the DBTT and USE compared to the as-welded condition

Thermal conductivity issues of EB-PVD thermal barrier coatings

Energy Technology Data Exchange (ETDEWEB)

Schulz, U.; Raetzer-Scheibe, H.J.; Saruhan, B. [DLR - German Aerospace Center, Institute of Materials Research, 51170 Cologne (Germany); Renteria, A.F. [BTU, Physical Metallurgy and Materials Technology, Cottbus (Germany)

2007-09-15

The thermal conductivity of electron-beam physical vapor deposited (EB-PVD) thermal barrier coatings (TBCs) was investigated by the Laser Flash technique. Sample type and methodology of data analyses as well as atmosphere during the measurement have some influence on the data. A large variation of the thermal conductivity was found by changes in TBC microstructure. Exposure at high temperature caused sintering of the porous microstructure that finally increased thermal conductivity up to 30 %. EB-PVD TBCs show a distinct thickness dependence of the thermal conductivity due to the anisotropic microstructure in thickness direction. Thin TBCs had a 20 % lower thermal conductivity than thick coatings. New compositions of the ceramic top layer offer the largest potential to lower thermal conductivity. Values down to 0.8W/(mK) have been already demonstrated with virgin coatings of pyrochlore compositions. (Abstract Copyright [2007], Wiley Periodicals, Inc.) [German] Die Waermeleitfaehigkeit von elektronenstrahl-aufgedampften (EB-PVD) Waermedaemmschichten (TBCs) wurde mittels Laser-Flash untersucht. Probentyp, Messmethodik und die Atmosphaere waehrend der Messung haben einen Einfluss auf die Ergebnisse. Aenderungen in der Mikrostruktur der TBC fuehrten zu grossen Unterschieden der Waermeleitfaehigkeit. Eine Hochtemperaturbelastung verursachte Sintervorgaenge in der poroesen Mikrostruktur, was die Waermeleitfaehigkeit um bis zu 30 % ansteigen liess. EB-PVD TBCs zeigen eine deutliche Dickenabhaengigkeit der Waermeleitfaehigkeit durch die Anisotropie der Mikrostruktur in dieser Richtung. Duenne TBCs haben eine um 20 % geringere Waermeleitfaehigkeit als dicke Schichten. Neue Zusammensetzungen der keramischen Deckschicht bieten die groessten Moeglichkeiten fuer eine Reduktion der Waermeleitfaehigkeit. Werte bis zu 0,8 W/(mK) wurden damit bereits erreicht. (Abstract Copyright [2007], Wiley Periodicals, Inc.)

Scania RBS brake system; Das Bremssystem EBS von Scania

Energy Technology Data Exchange (ETDEWEB)

Winterhagen, J.

1996-09-01

Scania claims to be the first producer of industrial vehicles to market an electronic braking system (EBS) combined with disc brakes for all axles. The new braking systems for long-distance trailers were presented for the first time at the IAA, Hanover, in September 1996. (orig.) [Deutsch] Scania ist nach eigenen Angaben der erste Lkw-Hersteller, der eine elektronisch geregelte Bremsanlage (EBS) in Kombination mit Scheibenbremsen an allen Achsen auf den Markt bringt. Der Oeffentlichkeit stellt Scania das neue Bremssystem fuer die Fernverkehrs-Zugmaschinen der Baureihe 4 zum ersten Mal auf der IAA in Hannover im September 1996 vor. (orig.)

E.B. White and Charlotte's Web.

Science.gov (United States)

Elledge, Scott

2001-01-01

Discusses the life and work of E.B. White, describing his research on spiders, examining his development of the story, "Charlotte's Web," and explaining how "Charlotte's Web" is a fabric of memories. Notes how this book faces a variety of truths about the human condition and how it celebrates a child's generous view of and love…

Formation of distinct inclusion bodies by inhibition of ubiquitin-proteasome and autophagy-lysosome pathways

International Nuclear Information System (INIS)

Lee, Junho; Yang, Kyu-Hwan; Joe, Cheol O.; Kang, Seok-Seong

2011-01-01

Research highlights: → Distinct inclusion bodies are developed by inhibition of UPP and ALP. → The inclusion bodies differ in morphology, localization and formation process. → The inclusion bodies are distinguishable by the localization of TSC2. → Inhibition of both UPP and ALP simultaneously induces those inclusion bodies. -- Abstract: Accumulation of misfolded proteins is caused by the impairment of protein quality control systems, such as ubiquitin-proteasome pathway (UPP) and autophagy-lysosome pathway (ALP). In this study, the formation of inclusion bodies was examined after the blockade of UPP and/or ALP in A549 cells. UPP inhibition induced a single and large inclusion body localized in microtubule-organizing center. Interestingly, however, ALP inhibition generated dispersed small inclusion bodies in the cytoplasm. Tuberous sclerosis complex 2 was selectively accumulated in the inclusion bodies of UPP-inhibited cells, but not those of ALP-inhibited cells. Blockade of transcription and translation entirely inhibited the formation of inclusion body induced by UPP inhibition, but partially by ALP inhibition. Moreover, the simultaneous inhibition of two protein catabolic pathways independently developed two distinct inclusion bodies within a single cell. These findings clearly demonstrated that dysfunction of each catabolic pathway induced formation and accumulation of unique inclusion bodies on the basis of morphology, localization and formation process in A549 cells.

The removal of VOC from air using EB, MW and catalyst - Laboratory plant results

International Nuclear Information System (INIS)

Calinescu, I.; Ighigeanu, D.; Martin, D.

2011-01-01

A new hybrid technique for the VOCs removal from gases, based on the combined use of EB induced NTP (non-thermal plasma), MW induced NTP and catalytic oxidation, named “EB+MW-plasma catalysis”, is presented. The main goal of our research was to combine the features of each known technique used in gas pollution control, i.e. the very high efficiency of EB in converting VOCs to intermediate products, the ability of MW to produce and sustain NTP in large electrodeless reactors, and the important role of catalysts in the complete conversion to CO 2 and H 2 O. Our experiences shown that the two means of treating the gases are complementary: the catalytic oxidation in the presence of MW is efficient for high VOC initial concentrations and low flow rates while the exclusive use of the EB irradiation determines high decomposition efficiencies only in the case of very low concentrations of VOC but for large flow rates. Real synergistic effects between NTP and catalysis were obtained by introducing the catalyst into the irradiation zone. The main conclusion of this work is that the combined treatment EB+MW+catalyst improves both decomposition efficiency and oxidation efficiency. The EB+MW+Catalysis method demonstrated good results on a wide range of concentrations and flow rates. (author)

EB dose calibration for 10 MeV linear accelerator

International Nuclear Information System (INIS)

Owczarczyk, H.B.; Migdal, W.; Stachowicz, W.

2002-01-01

The National Institute of Standards and Technology Gaitherburg USA has done in co-operation with INCT Warsaw the EPR dose measurements for two INCT 60 Co irradiators using l-alanine standard pellets as dosimeter medium. In the study the comparative EPR measurements of doses up to 40 kGy have been done using l-alanine powder with 60 Co source (reference to NIST standard) and EB linear accelerator, respectively. On the basis of this comparative study 5% correction factor for EB dose measurements has been adapted in the INCT Experimental Plant for Food Irradiation traceable to the dose estimations done with the Risoe calorimetric system

Modelling Coupled Processes in the Evolution of Repository Engineered Barrier Systems using QPAC-EBS

Energy Technology Data Exchange (ETDEWEB)

Maul, Philip; Benbow, Steven; Bond, Alex; Robinson, Peter (Quintessa Limited, Henley-on-Thames (United Kingdom))

2010-08-15

A satisfactory understanding of the evolution of repository engineered barrier systems (EBS) is an essential part of the safety case for the repository. This involves consideration of coupled Thermal (T), Hydro (H), Mechanical (M) and Chemical (C) processes. Quintessa's general-purpose modelling code QPAC is capable of representing strongly coupled non-linear processes and has been used in a wide range of applications. This code is the basis for software used by Quintessa in studies of the evolution of the EBS in a deep repository for spent nuclear fuel undertaken for SKI and then SSM since 2007. The collection of software components employed has been referred to collectively as QPAC-EBS, consisting of the core QPAC code together with relevant modules for T, H, M and C processes. QPAC-EBS employs a fundamentally different approach from dedicated codes that model such processes (although few codes can represent each type of process), enabling the specification of new processes and the associated governing equations in code input. Studies undertaken to date have demonstrated that QPAC-EBS can be used effectively to investigate both the early evolution of the EBS and important scenarios for the later evolution of the system when buffer erosion and canister corrosion may occur. A key issue for modelling EBS evolution is the satisfactory modelling of the behaviour of the bentonite buffer. Bentonite is a difficult material to model, partly because of the complex coupled mechanical, hydro and chemical processes involved in swelling during resaturation. Models employed to date have generally taken an empirical approach, but a new model developed during the EU THERESA project could be further developed to provide a better representation of these processes. QPAC-EBS could play an important role in supporting SSM.s review of the forthcoming SR-Site assessment by SKB if used by Quintessa in independent supporting calculations. To date radionuclide transport calculations

The removal of VOC from air using EB, MW and catalyst - Laboratory plant results

Energy Technology Data Exchange (ETDEWEB)

Calinescu, I. [Polytechnic University, Bucharest (Romania); Ighigeanu, D.; Martin, D. [National Institute for Lasers, Plasma and Radiation Physics, Bucharest (Romania)

2011-07-01

A new hybrid technique for the VOCs removal from gases, based on the combined use of EB induced NTP (non-thermal plasma), MW induced NTP and catalytic oxidation, named “EB+MW-plasma catalysis”, is presented. The main goal of our research was to combine the features of each known technique used in gas pollution control, i.e. the very high efficiency of EB in converting VOCs to intermediate products, the ability of MW to produce and sustain NTP in large electrodeless reactors, and the important role of catalysts in the complete conversion to CO{sub 2} and H{sub 2}O. Our experiences shown that the two means of treating the gases are complementary: the catalytic oxidation in the presence of MW is efficient for high VOC initial concentrations and low flow rates while the exclusive use of the EB irradiation determines high decomposition efficiencies only in the case of very low concentrations of VOC but for large flow rates. Real synergistic effects between NTP and catalysis were obtained by introducing the catalyst into the irradiation zone. The main conclusion of this work is that the combined treatment EB+MW+catalyst improves both decomposition efficiency and oxidation efficiency. The EB+MW+Catalysis method demonstrated good results on a wide range of concentrations and flow rates. (author)

Thermocyclic behaviour of microstructurally modified EB-PVD thermal barrier coatings

International Nuclear Information System (INIS)

Schulz, U.; Fritscher, K.; Raetzer-Scheibe, H.-J.; Kaysser, W.A.; Peters, M.

1997-01-01

This paper focuses on the combined effects of substrate temperature and rotation during electron-beam physical vapor deposition (EB-PVD) on the columnar microstructure of yttria partially stabilized zirconia (YPSZ) thermal barrier coatings. Diameter and degree of ordering of the columns and the density of the coatings are sensitive to the processing parameters. Results are discussed in the frame of common structural zone models for PVD processes. The models are extended to consider the rotational effect. EB-PVD YPSZ TBCs of different column diameters were deposited on top of an EB-PVD NiCoCrAlY bondcoat on IN 100 superalloy test bars. The performance of the TBCs was investigated in a cyclic oxidation furnace test rig between 1100 C and 130 C and in a burner rig under hot gas corrosion conditions at a maximum temperature of 900 C. Results showed a correlation between cyclic lifetime and the various microstructures of the TBCs. Samples having a non-regular arrangement of columns performed best in both tests. (orig.)

Candida septic arthritis with rice body formation: A case report and review of literature

International Nuclear Information System (INIS)

Jeong, Yu Mi; Cho, Hyun Yee; Lee, Sheen Woo; Hwang, Yun Mi; Kim, Young Kyu

2013-01-01

Rice body formation in a joint or bursa is a rare condition, and is usually associated with rheumatoid arthritis or tuberculous arthritis. Here we describe a case of multiple rice body formation in a shoulder joint and in adjacent bursae, which was confirmed to be due to septic arthritis by Candida species. To the best of our knowledge, rice body formation in Candida septic arthritis in an immune-competent patient has not been previously reported.

Candida septic arthritis with rice body formation: A case report and review of literature

Energy Technology Data Exchange (ETDEWEB)

Jeong, Yu Mi; Cho, Hyun Yee; Lee, Sheen Woo; Hwang, Yun Mi; Kim, Young Kyu [Gachon University, Gil Hospital, Incheon (Korea, Republic of)

2013-06-15

Rice body formation in a joint or bursa is a rare condition, and is usually associated with rheumatoid arthritis or tuberculous arthritis. Here we describe a case of multiple rice body formation in a shoulder joint and in adjacent bursae, which was confirmed to be due to septic arthritis by Candida species. To the best of our knowledge, rice body formation in Candida septic arthritis in an immune-competent patient has not been previously reported.

Formation of distinct inclusion bodies by inhibition of ubiquitin-proteasome and autophagy-lysosome pathways.

Science.gov (United States)

Lee, Junho; Yang, Kyu-Hwan; Joe, Cheol O; Kang, Seok-Seong

2011-01-14

Accumulation of misfolded proteins is caused by the impairment of protein quality control systems, such as ubiquitin-proteasome pathway (UPP) and autophagy-lysosome pathway (ALP). In this study, the formation of inclusion bodies was examined after the blockade of UPP and/or ALP in A549 cells. UPP inhibition induced a single and large inclusion body localized in microtubule-organizing center. Interestingly, however, ALP inhibition generated dispersed small inclusion bodies in the cytoplasm. Tuberous sclerosis complex 2 was selectively accumulated in the inclusion bodies of UPP-inhibited cells, but not those of ALP-inhibited cells. Blockade of transcription and translation entirely inhibited the formation of inclusion body induced by UPP inhibition, but partially by ALP inhibition. Moreover, the simultaneous inhibition of two protein catabolic pathways independently developed two distinct inclusion bodies within a single cell. These findings clearly demonstrated that dysfunction of each catabolic pathway induced formation and accumulation of unique inclusion bodies on the basis of morphology, localization and formation process in A549 cells. Copyright © 2010 Elsevier Inc. All rights reserved.

The EB factory project. II. Validation with the Kepler field in preparation for K2 and TESS

Energy Technology Data Exchange (ETDEWEB)

Parvizi, Mahmoud; Paegert, Martin; Stassun, Keivan G., E-mail: mahmoud.parvizi@vanderbilt.edu [Department of Physics and Astronomy, Vanderbilt University, VU Station B 1807, Nashville, TN 37235 (United States)

2014-12-01

Large repositories of high precision light curve data, such as the Kepler data set, provide the opportunity to identify astrophysically important eclipsing binary (EB) systems in large quantities. However, the rate of classical “by eye” human analysis restricts complete and efficient mining of EBs from these data using classical techniques. To prepare for mining EBs from the upcoming K2 mission as well as other current missions, we developed an automated end-to-end computational pipeline—the Eclipsing Binary Factory (EBF)—that automatically identifies EBs and classifies them into morphological types. The EBF has been previously tested on ground-based light curves. To assess the performance of the EBF in the context of space-based data, we apply the EBF to the full set of light curves in the Kepler “Q3” Data Release. We compare the EBs identified from this automated approach against the human generated Kepler EB Catalog of ∼2600 EBs. When we require EB classification with ⩾90% confidence, we find that the EBF correctly identifies and classifies eclipsing contact (EC), eclipsing semi-detached (ESD), and eclipsing detached (ED) systems with a false positive rate of only 4%, 4%, and 8%, while complete to 64%, 46%, and 32%, respectively. When classification confidence is relaxed, the EBF identifies and classifies ECs, ESDs, and EDs with a slightly higher false positive rate of 6%, 16%, and 8%, while much more complete to 86%, 74%, and 62%, respectively. Through our processing of the entire Kepler “Q3” data set, we also identify 68 new candidate EBs that may have been missed by the human generated Kepler EB Catalog. We discuss the EBF's potential application to light curve classification for periodic variable stars more generally for current and upcoming surveys like K2 and the Transiting Exoplanet Survey Satellite.

Near field and altered zone environmental report Volume I: technical bases for EBS design

Energy Technology Data Exchange (ETDEWEB)

Wilder, D. G., LLNL

1997-08-01

This report presents an updated summary of results for the waste package (WP) and engineered barrier system (EBS) evaluations, including materials testing, waste-form characterization, EBS performance assessments, and near-field environment (NFE) characterization. Materials testing, design criteria and concept development, and waste-form characterization all require an understanding of the environmental conditions that will interact with the WP and EBS. The Near-Field Environment Report (NFER) was identified in the Waste Package Plan (WPP) (Harrison- Giesler, 1991) as the formal means for transmitting and documenting this information.

Residual stress investigation of copper plate and canister EB-Welds Complementary Results

International Nuclear Information System (INIS)

Gripenberg, H.

2009-03-01

The residual stresses in copper as induced by EB-welding were studied by specimens where the weld had two configurations: either a linear or a circumferential weld. This report contains the residual stress measurements of two plates, containing linear welds, and the full-scale copper lid specimen to which a hollow cylinder section had been joined by a circumferential EB-weld. The residual stress state of the EB-welded copper specimens was investigated by X-ray diffraction (XRD), hole drilling (HD) ring core (RC) and contour method (CM). Three specimens, canister XK010 and plates X251 and X252, were subjected to a thorough study aiming at quantitative determination of the residual stress state in and around the EB-welds using XRD for surface and HD and RC for spatial stress analysis. The CM maps one stress component over a whole cross section. The surface residual stresses measured by XRD represent the machined condition of the copper material. The XRD study showed that the stress changes towards compression close to the weld in the hollow cylinder, which indicates shrinkage in the hoop direction. According to the same analogy, the shrinkage in the axial direction is much smaller. The HD measurements showed that the stress state in the base material is bi-axial and, in terms of von Mises stress, 50 MPa for the plates and 20 MPa for the cylinder part of the canister. The stress state in the EB-welds of all specimens differs clearly from the stress state in the base material being more tensile, with higher magnitudes of von Mises stress in the plate than in the canister welds. The HD and RC results were obtained using linear elastic theory. The RC measurements showed that the maximum principal stress in the BM is close to zero near the surface and it becomes slightly tensile, 10 MPa, deeper under the surface. Welding pushed the general stress state towards tension with the maximum principal stress reaching 50 MPa, deeper than 5 mm below the surface in the weld. The

Distinguishing multiple rice body formation in chronic subacromial-subdeltoid bursitis from synovial chondromatosis

International Nuclear Information System (INIS)

Chen, Albert; Wong, Lun-Yick; Sheu, Chin-Yin; Chen, Be-Fong

2002-01-01

Multiple rice body formation is a complication of chronic bursitis. Although it resembles synovial chondromatosis clinically and on imaging, the literature suggests that analysis of radiographic and MR appearances should allow discrimination. We report the imaging findings in a 41-year-old man presenting with rice body formation in chronic subacromial-subdeltoid bursitis. We found that the signal intensity of the rice bodies is helpful in making the diagnosis. (orig.)

Distinguishing multiple rice body formation in chronic subacromial-subdeltoid bursitis from synovial chondromatosis

Energy Technology Data Exchange (ETDEWEB)

Chen, Albert; Wong, Lun-Yick; Sheu, Chin-Yin [Department of Radiology, Mackay Memorial Hospital, Taipei (Taiwan); Chen, Be-Fong [Department of Pathology, Mackay Memorial Hospital, Taipei (Taiwan)

2002-02-01

Multiple rice body formation is a complication of chronic bursitis. Although it resembles synovial chondromatosis clinically and on imaging, the literature suggests that analysis of radiographic and MR appearances should allow discrimination. We report the imaging findings in a 41-year-old man presenting with rice body formation in chronic subacromial-subdeltoid bursitis. We found that the signal intensity of the rice bodies is helpful in making the diagnosis. (orig.)

[A case with chronic active EB virus infection accompanied with pulmonary candidiasis].

Science.gov (United States)

Karino, T; Nakamura, J; Fujita, K; Kobashi, Y; Yano, T; Okimoto, N; Soejima, R

1998-12-01

A 44-year-old woman with a history of intermittent fever for several years was admitted because of burn on her leg. On admission, she had hepatosplenomegaly and fever. Antibiotic therapy was started for bacterial infection of the burn. She lost her appetite and IVH was started. During the treatment, high fever appeared and chest X-ray films showed multiple nodular infiltrates throughout both lung fields. Candida albicans was isolated from IVH catheter culture and pulmonary candidiasis was suspected. Her fever and lung involvements were successfully treated with fluconazole. During the course, serum anti-EB-VCA-IgG antibody persisted at a high titer and anti-EBNA antibody remained negative. EB virus DNA was detected in the peripheral blood and bone marrow. Thus, she was diagnosed as chronic active EB virus infection.

Towards energy efficient climate control in storage of tulip bulbs. Pilot EB-01; Naar een energiezuiniger klimaatbeheersing bij de bewaring van tulpenbollen. Praktijkproef EB-01

Energy Technology Data Exchange (ETDEWEB)

Gude, H.; Dijkema, M.

2005-09-15

The aim of this project is to enable energy conservation in the storage of tulip bulbs. To this end, it should be examined if the agent EB-01 (1-methylcycloprene, a protection agent for plants) can be used in practical cells that are not entirely leak proof and if it offers sufficient protection against ethylene damage [Dutch] Doel van dit project is om energiebesparing bij de bewaring van tulpenbollen mogelijk te maken. Om dat te realiseren wordt onderzocht of het middel EB-01 (1- methylcyclopropeen, een beschermingsmiddel voor planten) toepasbaar is in niet volledig lekdichte praktijkcellen en voldoende bescherming tegen ethyleenschade biedt.

The addition of calcitriol or its synthetic analog EB1089 to lapatinib and neratinib treatment inhibits cell growth and promotes apoptosis in breast cancer cells.

Science.gov (United States)

Segovia-Mendoza, Mariana; Díaz, Lorenza; Prado-Garcia, Heriberto; Reginato, Mauricio J; Larrea, Fernando; García-Becerra, Rocío

2017-01-01

In breast cancer the use of small molecule inhibitors of tyrosine kinase activity of the ERBB family members improves survival thus represents a valuable therapeutic strategy. The addition of calcitriol, the most active metabolite of vitamin D, or some of its analogs, to conventional anticancer drugs, including tyrosine kinase inhibitors (TKIs), has shown an increased effect on the inhibition of cancer cell growth. In this work, we have evaluated the effects and the mechanism of action of the combination of calcitriol or its analog EB1089 with lapatinib or neratinib on EGFR and/or HER2 positive breast cancer cell lines. Lapatinib, neratinib, calcitriol and EB1089 inhibited breast cancer cell proliferation in a concentration-dependent manner. Addition of calcitriol or EB1089 to TKIs treatment induced more effective inhibiting effect on cell growth and AKT and MAPK phosphorylation than all compounds alone. The combined treatments incremented also the expression of active caspase 3 and induced cell death in two and three-dimensional cell culture and significantly inhibited anchorage-independent colony formation. Our results suggest that the addition of calcitriol or its analog EB1089 to conventional targeted therapies, including lapatinib or neratinib might be of benefit to patients with breast cancer, particularly those with an EGFR and/or HER2 positive phenotype.

EB-PVD process management for highly productive zirconia thermal barrier coating of turbine blades

International Nuclear Information System (INIS)

Reinhold, E.; Botzler, P.; Deus, C.

1999-01-01

Zirconia thermal barrier coatings are well used in the turbine manufacturing industry because they ensure extended lifetimes of turbine blades. Compared with other techniques, EB-PVD processes are best suited for the deposition on turbine blades with regard to the layer properties. Therefore EB-PVD coaters for turbine blades are becoming increasingly interesting. The coating costs per component are mainly dependent on a highly productive solution for the deposition task. Thus the EB-PVD process management has to be optimized in order to meet the productivity requirements of the manufacturers. This includes the requirement of high deposition rates, large deposition areas, long time stable production cycles as well as a matched duration of preheating, deposition and cooling down per charge. Modern EB-PVD solutions to be introduced allow deposition rates on blades up to 7 μm/min. The consequences for the technological process management and plant design concerning long time stable coating cycles with high productivity will be discussed. (orig.)

Observing Planets and Small Bodies in Sputtered High Energy Atom (SHEA) Fluxes

Science.gov (United States)

Milillo, A.; Orsini, S.; Hsieh, K. C.; Baragiola, R.; Fama, M.; Johnson, R.; Mura, A.; Plainaki, Ch.; Sarantos, M.; Cassidy, T. A.;

Influence of boundary effects on electron beam dose distribution formation in multilayer targets

International Nuclear Information System (INIS)

Kaluska, I.; Zimek, Z.; Lazurik, V.T.; Lazurik, V.M.; Popov, G.F.; Rogov, Y.V.

2010-01-01

Computational dosimetry play a significant role in an industrial radiation processing at dose measurements in the product irradiated with electron beams (EB), X-ray and gamma ray from radionuclide sources. Accurate and validated programs for absorbed dose calculations are required for computational dosimetry. The program ModeStEB (modelling of EB processing in a three-dimensional (3D) multilayer flat targets) was designed specially for simulation and optimization of industrial radiation processing, calculation of the 3D absorbed dose distribution within multilayer packages. The package is irradiated with scanned EB on an industrial radiation facility that is based on the pulsed or continuous type of electron accelerators in the electron energy range from 0.1 to 25 MeV. Simulation of EB dose distributions in the multilayer targets was accomplished using the Monte Carlo (MC) method. Experimental verification of MC simulation prediction for EB dose distribution formation in a stack of plates interleaved with polyvinylchloride (PVC) dosimetric films (DF), within a packing box, and irradiated with a scanned 10 MeV EB on a moving conveyer is discussed. (authors)

Gastric Perforation and Phlegmon Formation by Foreign Body Ingestion

Directory of Open Access Journals (Sweden)

Albert Alejandro Avila Alvarez

2014-08-01

Full Text Available This is a case report of foreign body ingestion in a suicide attempt resulting in gastric perforation and phlegmon formation during a subsequent 6 month period that eventually required surgical intervention. The patient had a prolonged course because she did not report a history of foreign body ingestion and the initial evaluating physicians had no suspicion about possible foreign body ingestion and may have missed important findings on physical examination. Gastric perforation by a foreign object  may have a slow course rather than presenting acute abdomen. The realization of a proper physical examination in the emergency department is key to an accurate diagnosis.

A Application of WD Model to EB Type Contact Binary System

Directory of Open Access Journals (Sweden)

Su-Yeon Oh

2000-12-01

Full Text Available The EB type contact binaries show large temperature difference ( T 1,000K between two components. Thus we have modified the mode 3 of the WD program to adjust albedos, limb darkening coefficients and gravity darkening exponents for both components of such binaries, while the values for those parameters should be same for both components in the original WD program. Both of the modified and the original versions have been applied to the EB type contact binaries such as DO Cas, GO Cyg, and FS Lup. The computed light curves with modified version fit better to the observations.

EB-promoted recycling of waste tire rubber with polyolefins

Science.gov (United States)

Mészáros, László; Bárány, Tamás; Czvikovszky, Tibor

2012-09-01

Despite the fact that more and more methods and solutions are used in the recycling of polymers, there are still some problems, especially in the recycling of cross-linked materials such as rubber. Usually the biggest problem is the lack of compatibility between the cross-linked rubber and the thermoplastic matrix. In this study we applied ground tire rubber (GTR) as recycled material. The GTR was embedded into polyethylene (PE) and polyethylene/ethylene-vinyl acetate copolymer (PE/EVA) matrices. In order to increase the compatibility of the components electron beam (EB) irradiation was applied. The results showed that the irradiation has a beneficial effect on the polymer-GTR interfacial connection. The EB treatment increased not only the tensile strength but also the elongation at break. The irradiation had also positive effect on the impact strength properties.

Nuclear bodies: news insights into structure and function

Czech Academy of Sciences Publication Activity Database

Staněk, David; Fox, A.H.

2017-01-01

Roč. 46, léto (2017), s. 94-101 ISSN 0955-0674 R&D Projects: GA ČR GA15-00790S; GA MŠk LO1419 Institutional support: RVO:68378050 Keywords : rna-binding proteins * cajal bodies * smn complex * human-cells * in-vivo * human telomerase * coiled bodies * lncrna neat1 * u1 snrnp * body Subject RIV: EB - Genetics ; Molecular Biology OBOR OECD: Cell biology Impact factor: 9.937, year: 2016

Evaluation of parameters associated with UV/EB cured clearcoats degradation used in outdoor environment

International Nuclear Information System (INIS)

Ruiz, Carmen Silvia Bentivoglio

2003-01-01

The materials curable by ultraviolet (UV) or electron beam (EB) radiation such as inks, adhesives and coatings are reactive compounds made up of resin, monomer, photoinitiator and additives which undergo polymerization and crosslinking under irradiation producing thermoset products. This technology has been used in a great variety of industrial applications, replacing the conventional curing process in the development of new products. One of the challenging applications has been to design weatherable radiation cured coating which maintain their desirable physical properties and aesthetic appearance. This research reports information about the behavior of four UV and EB curable clear coatings -with or without light stabilizer additives- under accelerated weathering. Thermogravimetry, differential scanning calorimetry, differential photo calorimetry, infrared and ultraviolet spectroscopy and tensile properties were used to evaluate these formulations. Clear coating 50 mum thick films were cured with UV and EB radiation at different doses. The UV curing process was carried out at room temperature using an UV tunnel, with a medium pressure mercury lamp and a transport belt with variable speed. The ultraviolet radiation doses were in the range of 50 to 1500 mJ cm -2 . The EB curing process was performed under N 2 atmosphere, with doses in the range from 1,6 to 300 kGy using the IPEN-CNEN/SP Dynamitron electron beam accelerator with energy of 1.5 MeV. The cure degree was determined by means of the residual reaction heat of the under cured samples obtained from photo-DSC or DSC measurements. The accelerated aging tests were carried out using a Weather-Ometer chamber with exposition times in the range of 100 to 3000 hours. The experimental data obtained from the photo-aged samples were evaluated and correlated to the formulation composition, type of radiation - UV or EB, radiation dose and residence time in the aging chamber. The results have shown that the EB cured films

The Integration and Abstracyion of EBS Models in Yucca Mountain Performance Assessment

Energy Technology Data Exchange (ETDEWEB)

S.D. Sevougian; V. Jain; A.V. Luik

2006-01-11

The safety strategy for geological disposal of radioactive waste at Yucca Mountain relies on a multi-barrier system to contain the waste and isolate it from the biosphere. The multi-barrier system consists of the natural barrier provided by the geological setting and the engineered barrier system (EBS). In the case of Yucca Mountain (YM) the geologic setting is the unsaturated-zone host rock, consisting of about 600 meters of layered ash-flow volcanic tuffs above the water table, and the saturated zone beneath the water table. Both the unsaturated and saturated rocks are part of a closed hydrologic basin in a desert surface environment. The waste is to be buried about halfway between the desert surface and the water table. The primary engineered barriers at YM consist of metal components that are highly durable in an oxidizing environment. The two primary components of the engineered barrier system are highly corrosion-resistant metal waste packages, made from a nickel-chromium-molybdenum alloy, Alloy 22, and titanium drip shields that protect the waste packages from corrosive dripping water and falling rocks. Design and performance assessment of the EBS requires models that describe how the EBS and near field behave under anticipated repository-relevant conditions. These models must describe coupled hydrologic, thermal, chemical, and mechanical (THCM) processes that drive radionuclide transport in a highly fractured host rock, consisting of a relatively permeable network of conductive fractures in a setting of highly impermeable tuff rock matrix. An integrated performance assessment of the EBS must include a quantification of the uncertainties that arise from (1) incomplete understanding of processes and (2) from lack of data representative of the large spatial scales and long time scales relevant to radioactive waste disposal (e.g., long-term metal corrosion rates and heterogeneities in rock properties over the large 5 km{sup 2} emplacement area of the repository

The Integration and Abstraction of EBS Models in Yucca Mountain Performance Assessment

International Nuclear Information System (INIS)

S.D. Sevougian; V. Jain; A.V. Luik

2006-01-01

The safety strategy for geological disposal of radioactive waste at Yucca Mountain relies on a multi-barrier system to contain the waste and isolate it from the biosphere. The multi-barrier system consists of the natural barrier provided by the geological setting and the engineered barrier system (EBS). In the case of Yucca Mountain (YM) the geologic setting is the unsaturated-zone host rock, consisting of about 600 meters of layered ash-flow volcanic tuffs above the water table, and the saturated zone beneath the water table. Both the unsaturated and saturated rocks are part of a closed hydrologic basin in a desert surface environment. The waste is to be buried about halfway between the desert surface and the water table. The primary engineered barriers at YM consist of metal components that are highly durable in an oxidizing environment. The two primary components of the engineered barrier system are highly corrosion-resistant metal waste packages, made from a nickel-chromium-molybdenum alloy, Alloy 22, and titanium drip shields that protect the waste packages from corrosive dripping water and falling rocks. Design and performance assessment of the EBS requires models that describe how the EBS and near field behave under anticipated repository-relevant conditions. These models must describe coupled hydrologic, thermal, chemical, and mechanical (THCM) processes that drive radionuclide transport in a highly fractured host rock, consisting of a relatively permeable network of conductive fractures in a setting of highly impermeable tuff rock matrix. An integrated performance assessment of the EBS must include a quantification of the uncertainties that arise from (1) incomplete understanding of processes and (2) from lack of data representative of the large spatial scales and long time scales relevant to radioactive waste disposal (e.g., long-term metal corrosion rates and heterogeneities in rock properties over the large 5 km 2 emplacement area of the repository). A

Differentiating Mouse Embryonic Stem Cells into Embryoid Bodies by Hanging-Drop Cultures.

Science.gov (United States)

Behringer, Richard; Gertsenstein, Marina; Nagy, Kristina Vintersten; Nagy, Andras

2016-12-01

Embryonic stem (ES) cells can develop into many types of differentiated tissues if they are placed into a differentiating environment. This can occur in vivo when the ES cells are injected into or aggregated with an embryo, or in vitro if their culture conditions are modified to induce differentiation. There are an increasing number of differentiating culture conditions that can bias the differentiation of ES cells into desired cell types. Determining the mechanisms that control ES cell differentiation into therapeutically important cell types is a quickly growing area of research. Knowledge gained from these studies may eventually lead to the use of stem cells to repair specific damaged tissues. Many times ES cell differentiation proceeds through an intermediate stage called the embryoid body (EB). EBs are round structures composed of ES cells that have undergone some of the initial stages of differentiation. EBs can then be manipulated further to generate more specific cell types. This protocol describes a method to differentiate ES cells into EBs. It produces EBs of comparable size. This aspect is important because the differentiation processes taking place inside an EB are influenced by its size. © 2016 Cold Spring Harbor Laboratory Press.

Generating size-controlled embryoid bodies using laser direct-write

International Nuclear Information System (INIS)

Dias, A D; Corr, D T; Unser, A M; Xie, Y; Chrisey, D B

2014-01-01

Embryonic stem cells (ESCs) have the potential to self-renew and differentiate into any specialized cell type. One common method to differentiate ESCs in vitro is through embryoid bodies (EBs), three-dimensional cellular aggregates that spontaneously self-assemble and generally express markers for the three germ layers, endoderm, ectoderm, and mesoderm. It has been previously shown that both EB size and 2D colony size each influence differentiation. We hypothesized that we could control the size of the EB formed by mouse ESCs (mESCs) by using a cell printing method, laser direct-write (LDW), to control both the size of the initial printed colony and the local cell density in printed colonies. After printing mESCs at various printed colony sizes and printing densities, two-way ANOVAs indicated that the EB diameter was influenced by printing density after three days (p = 0.0002), while there was no effect of the printed colony diameter on the EB diameter at the same timepoint (p = 0.74). There was no significant interaction between these two factors. Tukey's honestly significant difference test showed that high-density colonies formed significantly larger EBs, suggesting that printed mESCs quickly aggregate with nearby cells. Thus, EBs can be engineered to a desired size by controlling printing density, which will influence the design of future differentiation studies. Herein, we highlight the capacity of LDW to control the local cell density and colony size independently, at prescribed spatial locations, potentially leading to better stem cell maintenance and directed differentiation. (paper)

Engineered barrier systems (EBS) in the context of the entire safety case

International Nuclear Information System (INIS)

2003-01-01

A joint NEA-EC workshop entitled 'Engineered Barrier Systems (EBS) in the Context of the Entire Safety Case' was organised in Oxford on 25-27 September 2002 and hosted by United Kingdom Nirex Limited. The main objectives of the workshop were to provide a status report on engineered barrier systems in various national radioactive waste management programmes considering deep geological disposal; to establish the value to member countries of a project on EBS; and to define such a project's scope, timetable and modus operandi. This report presents the outcomes of this workshop. (author)

Engineered Barrier Systems (EBS) in the Context of the Entire Safety Case

International Nuclear Information System (INIS)

2005-01-01

A joint NEA-EC workshop entitled ''Engineered Barrier Systems (EBS) in the Context of the Entire Safety Case'' was organised in Oxford on 25-27 September 2002 and hosted by United Kingdom Nirex Limited. The main objectives of the workshop were to provide a status report on engineered barrier systems in various national radioactive waste management programmes considering deep geological disposal; to establish the value to member countries of a project on EBS; and to define such a project scope, timetable and modus operandi. This report presents the outcomes of this workshop. (author)

Polyurethane acrylate networks including cellulose nanocrystals: a comparison between UV and EB- curing

International Nuclear Information System (INIS)

Furtak-Wrona, K.; Kozik-Ostrówka, P.; Jadwiszczak, K.; Maigret, J.E.; Aguié-Béghin, V.; Coqueret, X.

2018-01-01

A water-based polyurethane (PUR) acrylate water emulsion was selected as a radiation curable matrix for preparing nanocomposites including cellulose nanocrystals (CNC) prepared by controlled hydrolysis of Ramie fibers. Cross-linking polymerization of samples prepared in the form of films or of 1 mm-thick bars was either initiated by exposure to the 395 nm light of a high intensity LED lamp or by treatment with low energy electron beam (EB). The conversion level of acrylate functions in samples submitted to increasing radiation doses was monitored by Fourier Transform Infrared Spectroscopy (FTIR). Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) were used to characterize changes in the glass transition temperature of the PUR-CNC nanocomposites as a function of acrylate conversion and of CNC content. Micromechanical testing indicates the positive effect of 1 wt% CNC on Young's modulus and on the tensile strength at break (σ) of cured nanocomposites. The presence of CNC in the PUR acrylate matrix was shown to double the σ value of the nanocomposite cured to an acrylate conversion level of 85% by treatment with a 25 kGy dose under EB, whereas no increase of σ was observed in UV-cured samples exhibiting the same acrylate conversion level. The occurrence of grafting reactions inducing covalent linkages between the polysaccharide nanofiller and the PUR acrylate matrix during the EB treatment is advanced as an explanation to account for the improvement observed in samples cured under ionizing radiation. - Highlights: • Nanocomposites were prepared from o/w PUR acrylate emulsion and CNC suspension. • Nanocomposite and reference materials were cured to the same conversion by UV or EB. • Introducing 1 wt% CNC in EB-cured composites doubles the tensile strength. • UV-cured nanocomposites did not show significant improvement in tensile strength.

Current and future market of UV/EB curing in Thailand

International Nuclear Information System (INIS)

Suda Kiatkamjornwong; Aran Hanseubsai

1999-01-01

Current status and future market of UV/EB curing in Thailand were presented. Included number of printing houses, export, main export market and the role of radiation curing in printing and packaging industries of Thailand

Three New Pierce's Disease Pathogenicity Effectors Identified Using Xylella fastidiosa Biocontrol Strain EB92-1.

Science.gov (United States)

Zhang, Shujian; Chakrabarty, Pranjib K; Fleites, Laura A; Rayside, Patricia A; Hopkins, Donald L; Gabriel, Dean W

2015-01-01

Xylella fastidiosa (X. fastidiosa) infects a wide range of plant hosts and causes economically serious diseases, including Pierce's Disease (PD) of grapevines. X. fastidiosa biocontrol strain EB92-1 was isolated from elderberry and is infectious and persistent in grapevines but causes only very slight symptoms under ideal conditions. The draft genome of EB92-1 revealed that it appeared to be missing genes encoding 10 potential PD pathogenicity effectors found in Temecula1. Subsequent PCR and sequencing analyses confirmed that EB92-1 was missing the following predicted effectors found in Temecula1: two type II secreted enzymes, including a lipase (LipA; PD1703) and a serine protease (PD0956); two identical genes encoding proteins similar to Zonula occludens toxins (Zot; PD0915 and PD0928), and at least one relatively short, hemagglutinin-like protein (PD0986). Leaves of tobacco and citrus inoculated with cell-free, crude protein extracts of E. coli BL21(DE3) overexpressing PD1703 exhibited a hypersensitive response (HR) in less than 24 hours. When cloned into shuttle vector pBBR1MCS-5, PD1703 conferred strong secreted lipase activity to Xanthomonas citri, E. coli and X. fastidiosa EB92-1 in plate assays. EB92-1/PD1703 transformants also showed significantly increased disease symptoms on grapevines, characteristic of PD. Genes predicted to encode PD0928 (Zot) and a PD0986 (hemagglutinin) were also cloned into pBBR1MCS-5 and moved into EB92-1; both transformants also showed significantly increased symptoms on V. vinifera vines, characteristic of PD. Together, these results reveal that PD effectors include at least a lipase, two Zot-like toxins and a possibly redundant hemagglutinin, none of which are necessary for parasitic survival of X. fastidiosa populations in grapevines or elderberry.

Three New Pierce's Disease Pathogenicity Effectors Identified Using Xylella fastidiosa Biocontrol Strain EB92-1.

Directory of Open Access Journals (Sweden)

Shujian Zhang

Full Text Available Xylella fastidiosa (X. fastidiosa infects a wide range of plant hosts and causes economically serious diseases, including Pierce's Disease (PD of grapevines. X. fastidiosa biocontrol strain EB92-1 was isolated from elderberry and is infectious and persistent in grapevines but causes only very slight symptoms under ideal conditions. The draft genome of EB92-1 revealed that it appeared to be missing genes encoding 10 potential PD pathogenicity effectors found in Temecula1. Subsequent PCR and sequencing analyses confirmed that EB92-1 was missing the following predicted effectors found in Temecula1: two type II secreted enzymes, including a lipase (LipA; PD1703 and a serine protease (PD0956; two identical genes encoding proteins similar to Zonula occludens toxins (Zot; PD0915 and PD0928, and at least one relatively short, hemagglutinin-like protein (PD0986. Leaves of tobacco and citrus inoculated with cell-free, crude protein extracts of E. coli BL21(DE3 overexpressing PD1703 exhibited a hypersensitive response (HR in less than 24 hours. When cloned into shuttle vector pBBR1MCS-5, PD1703 conferred strong secreted lipase activity to Xanthomonas citri, E. coli and X. fastidiosa EB92-1 in plate assays. EB92-1/PD1703 transformants also showed significantly increased disease symptoms on grapevines, characteristic of PD. Genes predicted to encode PD0928 (Zot and a PD0986 (hemagglutinin were also cloned into pBBR1MCS-5 and moved into EB92-1; both transformants also showed significantly increased symptoms on V. vinifera vines, characteristic of PD. Together, these results reveal that PD effectors include at least a lipase, two Zot-like toxins and a possibly redundant hemagglutinin, none of which are necessary for parasitic survival of X. fastidiosa populations in grapevines or elderberry.

Sensitivity of the engineered barrier system (EBS) release rate to alternative conceptual models of advective release from waste packages under dripping fractures

International Nuclear Information System (INIS)

Lee, J.H.; Atkins, J.E.; McNeish, J.A.; Vallikat, V.

1996-01-01

Simulations were conducted to analyze the sensitivity of the engineered barrier system (EBS) release rate to alternative conceptual models of the advective release from waste packages under dripping fractures. The first conceptual model assumed that dripping water directly contacts the waste form inside the 'failed' waste package, and radionuclides are released from the EBS by advection. The second conceptual model assumed that dripping water is diverted around the 'failed' waste package (because of the presence of corrosion products plugging the perforations) and dripping water is prevented from directly contacting the waste form. In the second model, radionuclides were assumed to transport through the perforations by diffusion, and, once outside the waste package, to be released from the EBS by advection. The second model was to incorporate more realism into the EBS release calculations. For the case with the second EBS release model, most radionuclides had significantly lower peak EBS release rates (from at least one to several orders of magnitude) than with the first EBS release model. The impacts of the alternative EBS release models were greater for the radionuclides with a low solubility (or solubility-limited radionuclides) than for the radionuclides with a high solubility (or waste form dissolution-limited radionuclides). The analyses indicated that the EBS release model representing advection through a 'failed' waste package (the first EBS release model) may be too conservative in predicting the EBS performance. One major implication from this sensitivity study was that a 'failed' waste package container with multiple perforations may still be able to perform effectively as an important barrier to radionuclide release. (author)

Current status of low energy EB machine

International Nuclear Information System (INIS)

Toshiro Nishikimi; Shuichi Taniguchi; Kenichi Mizusawa

1999-01-01

Electron beam processing systems have been in use in a variety of applications such as curing of paints and printing inks, crosslinking of PE products, treating of rubber tire and so on. Low energy electron processing systems have become popular as self-shielded machines, which are compact and easy to use and do not require special facility as an irradiation room. This manuscript introduces the status of low energy EB (electron beam) machine through Nissin's products current

Surface characteristics of hydroxyapatite-coated layer prepared on nanotubular Ti–35Ta–xHf alloys by EB-PVD

Energy Technology Data Exchange (ETDEWEB)

Jeong, Yong-Hoon [Department of Dental Materials and Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University, Gwangju (Korea, Republic of); Biomechanics and Tissue Engineering Laboratory, Division of Orthodontics, College of Dentistry, The Ohio State University, Columbus, OH (United States); Moon, Byung-Hak [Department of Dental Materials and Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University, Gwangju (Korea, Republic of); Choe, Han-Cheol, E-mail: hcchoe@chosun.ac.kr [Department of Dental Materials and Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University, Gwangju (Korea, Republic of); Brantley, William A. [Division of Restorative, Prosthetic and Primary Care Dentistry, College of Dentistry, The Ohio State University, Columbus, OH (United States)

2013-12-31

In this study, we investigated the surface characteristics of hydroxyapatite (HA)-coated layers prepared by electron-beam physical vapor deposition (EB-PVD) on nanotubular Ti–35Ta–xHf alloys (x = 3, 7, and 15 wt.%). Ti–35Ta–xHf alloys were first prepared by arc melting. Formation of a nanotube structure on these alloys was achieved by an electrochemical method in 1 M H{sub 3}PO{sub 4} + 0.8 wt.% NaF electrolytes. The HA coatings were then deposited on the nanotubular surface by an EB-PVD method. The surface characteristics were analyzed by field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction (XRD). The electrochemical behavior was examined using a potentiodynamic polarization test in 0.9% NaCl solution. The Ti–35Ta–xHf alloys had an equiaxed grain structure with α″ + β phases, and the α″ phase disappeared with increases in Hf content. The Ti–35Ta–15Hf alloy showed higher β-phase peak intensity in the XRD patterns than that for the lower Hf-content alloys. A highly ordered nanotubular oxide layer was formed on the Ti–35Ta–15Hf alloy, and the tube length depended on Hf content. The HA coating surface formed at traces of the nanotubular titanium oxide layer and completely covered the tips of the nanotubes with a cluster shape. From the potentiodynamic polarization tests, the incorporation of Hf element and formation of the nanotubular structure were the main factors for achieving lower current density. In particular, the surface of the HA coating on the nanotubular structure exhibited higher corrosion resistance than that of the nanotubular titanium oxide structure without an HA coating. - Highlights: • Hydroxyapatite (HA) was coated on nanotubular Ti–35Ta–xHf alloys, using EB-PVD. • Increasing the Hf content reduced the relative proportion of α″ martensite to β-Ti in the microstructures. • The detailed nanotubular structure formed by anodization depended on alloy composition

Surface characteristics of hydroxyapatite-coated layer prepared on nanotubular Ti–35Ta–xHf alloys by EB-PVD

International Nuclear Information System (INIS)

Jeong, Yong-Hoon; Moon, Byung-Hak; Choe, Han-Cheol; Brantley, William A.

2013-01-01

In this study, we investigated the surface characteristics of hydroxyapatite (HA)-coated layers prepared by electron-beam physical vapor deposition (EB-PVD) on nanotubular Ti–35Ta–xHf alloys (x = 3, 7, and 15 wt.%). Ti–35Ta–xHf alloys were first prepared by arc melting. Formation of a nanotube structure on these alloys was achieved by an electrochemical method in 1 M H 3 PO 4 + 0.8 wt.% NaF electrolytes. The HA coatings were then deposited on the nanotubular surface by an EB-PVD method. The surface characteristics were analyzed by field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction (XRD). The electrochemical behavior was examined using a potentiodynamic polarization test in 0.9% NaCl solution. The Ti–35Ta–xHf alloys had an equiaxed grain structure with α″ + β phases, and the α″ phase disappeared with increases in Hf content. The Ti–35Ta–15Hf alloy showed higher β-phase peak intensity in the XRD patterns than that for the lower Hf-content alloys. A highly ordered nanotubular oxide layer was formed on the Ti–35Ta–15Hf alloy, and the tube length depended on Hf content. The HA coating surface formed at traces of the nanotubular titanium oxide layer and completely covered the tips of the nanotubes with a cluster shape. From the potentiodynamic polarization tests, the incorporation of Hf element and formation of the nanotubular structure were the main factors for achieving lower current density. In particular, the surface of the HA coating on the nanotubular structure exhibited higher corrosion resistance than that of the nanotubular titanium oxide structure without an HA coating. - Highlights: • Hydroxyapatite (HA) was coated on nanotubular Ti–35Ta–xHf alloys, using EB-PVD. • Increasing the Hf content reduced the relative proportion of α″ martensite to β-Ti in the microstructures. • The detailed nanotubular structure formed by anodization depended on alloy composition. • The

[Establishment of sprouting embryoid body model mimicking early embryonic vasculogenesis in human embryo].

Science.gov (United States)

Jiang, Hua; Feng, You-Ji; Xie, Yi; Han, Jin-Lan; Wang, Zack; Chen, Tong

2008-10-14

To establish a sprouting embryoid body model mimicking early embryonic vasculogenesis in human embryo. Human embryonic stem were (hESCs) were cultured on the mouse embryo fibroblasts and then were induced to differentiate to form three-dimensional EB. The hEBs were cultured in media containing various angiogenesis-related factors: vascular endothelial growth factor (VEGF), fibroblast growth factor (FGF), endostatin, angiostatin, and platelet factor (PF)-4 of different concentrations for 3 days to observe the sprouting of the hEBs. 3, 3, 3', 3'-tetramethylindo-carbocyanine perchlorate labeled acetylated low density lipoprotein (Dil-AcLDL) was added onto the hEBs foe 4 h Immunofluorescence assay was used to observe if Dil-AcLDL was absorbed and if CD31 was expressed so as to determine the existence of embryonic endothelial cells in the sprouting structures. The ideal culturing condition was analyzed. The differentiated EBs formed sprouting structures in the collagen I matrix containing VEGF and FGF. The sprouts among individual EBs were able to link to each other and form vascular network-like structures. In the presence of VEGF and FGF, the sprouts branching from the EBs assimilated Dil-AcLDL, expressed CD31 and formed a 3-dimensional cylindrical organization. The concentrations of growth factors ideally stimulating sprouting growth were 100 ng/ml of VEGF and 50 ng/ml of FGF. The networks among the EBs were abolished by the angiostatin, endostatin, and PF4. The sprouting from hEBs accumulates embryonic endothelial cells and the sprouting network-like structures are indeed endothelial in nature. Inducing of sprouting EBs is an ideal model that mimics early embryonic vasculogenesis in humans.

Anti-migratory effect of vinflunine in endothelial and glioblastoma cells is associated with changes in EB1 C-terminal detyrosinated/tyrosinated status.

Directory of Open Access Journals (Sweden)

Amandine Rovini

Full Text Available We previously showed that vinflunine, a microtubule-targeting drug of the Vinca-alkaloid family exerted its anti-angiogenic/anti-migratory activities through an increase in microtubule dynamics and an inhibition of microtubule targeting to adhesion sites. Such effect was associated with a reduction of EB1 comet length at microtubule (+ ends. In this work we first showed that the pro-angiogenic vascular endothelial growth factor VEGF suppressed microtubule dynamics in living Human Umbilical Vein Endothelial Cells (HUVECs, increased EB1 comet length by 40%, and induced EB1 to bind all along the microtubules, without modifying its expression level. Such microtubule (+ end stabilization occurred close to the plasma membrane in the vicinity of focal adhesion as shown by TIRF microscopy experiments. Vinflunine completely abolished the effect of VEGF on EB1 comets. Interestingly, we found a correlation between the reduction of EB1 comet length by vinflunine and the inhibition of cell migration. By using 2D gel electrophoresis we demonstrated for the first time that EB1 underwent several post-translational modifications in endothelial and tumor cells. Particularly, the C-terminal EEY sequence was poorly detectable in control and VEGF-treated HUVECs suggesting the existence of a non-tyrosinated form of EB1. By using specific antibodies that specifically recognized and discriminated the native tyrosinated form of EB1 and a putative C-terminal detyrosinated form, we showed that a detyrosinated form of EB1 exists in HUVECs and tumor cells. Interestingly, vinflunine decreased the level of the detyrosinated form and increased the native tyrosinated form of EB1. Using 3-L-Nitrotyrosine incorporation experiments, we concluded that the EB1 C-terminal modifications result from a detyrosination/retyrosination cycle as described for tubulin. Altogether, our results show that vinflunine inhibits endothelial cell migration through an alteration of EB1 comet length

Human Metapneumovirus Induces Formation of Inclusion Bodies for Efficient Genome Replication and Transcription.

Science.gov (United States)

Cifuentes-Muñoz, Nicolás; Branttie, Jean; Slaughter, Kerri Beth; Dutch, Rebecca Ellis

2017-12-15

Human metapneumovirus (HMPV) causes significant upper and lower respiratory disease in all age groups worldwide. The virus possesses a negative-sense single-stranded RNA genome of approximately 13.3 kb encapsidated by multiple copies of the nucleoprotein (N), giving rise to helical nucleocapsids. In addition, copies of the phosphoprotein (P) and the large RNA polymerase (L) decorate the viral nucleocapsids. After viral attachment, endocytosis, and fusion mediated by the viral glycoproteins, HMPV nucleocapsids are released into the cell cytoplasm. To visualize the subsequent steps of genome transcription and replication, a fluorescence in situ hybridization (FISH) protocol was established to detect different viral RNA subpopulations in infected cells. The FISH probes were specific for detection of HMPV positive-sense RNA (+RNA) and viral genomic RNA (vRNA). Time course analysis of human bronchial epithelial BEAS-2B cells infected with HMPV revealed the formation of inclusion bodies (IBs) from early times postinfection. HMPV IBs were shown to be cytoplasmic sites of active transcription and replication, with the translation of viral proteins being closely associated. Inclusion body formation was consistent with an actin-dependent coalescence of multiple early replicative sites. Time course quantitative reverse transcription-PCR analysis suggested that the coalescence of inclusion bodies is a strategy to efficiently replicate and transcribe the viral genome. These results provide a better understanding of the steps following HMPV entry and have important clinical implications. IMPORTANCE Human metapneumovirus (HMPV) is a recently discovered pathogen that affects human populations of all ages worldwide. Reinfections are common throughout life, but no vaccines or antiviral treatments are currently available. In this work, a spatiotemporal analysis of HMPV replication and transcription in bronchial epithelial cell-derived immortal cells was performed. HMPV was shown to

Dissecting the nanoscale distributions and functions of microtubule-end-binding proteins EB1 and ch-TOG in interphase HeLa cells.

Directory of Open Access Journals (Sweden)

Satoko Nakamura

Full Text Available Recently, the EB1 and XMAP215/TOG families of microtubule binding proteins have been demonstrated to bind autonomously to the growing plus ends of microtubules and regulate their behaviour in in vitro systems. However, their functional redundancy or difference in cells remains obscure. Here, we compared the nanoscale distributions of EB1 and ch-TOG along microtubules using high-resolution microscopy techniques, and also their roles in microtubule organisation in interphase HeLa cells. The ch-TOG accumulation sites protruded ∼100 nm from the EB1 comets. Overexpression experiments showed that ch-TOG and EB1 did not interfere with each other's localisation, confirming that they recognise distinct regions at the ends of microtubules. While both EB1 and ch-TOG showed similar effects on microtubule plus end dynamics and additively increased microtubule dynamicity, only EB1 exhibited microtubule-cell cortex attachment activity. These observations indicate that EB1 and ch-TOG regulate microtubule organisation differently via distinct regions in the plus ends of microtubules.

Thermal Conductivity of EB-PVD Thermal Barrier Coatings Evaluated by a Steady-State Laser Heat Flux Technique

Science.gov (United States)

Zhu, Dongming; Miller, Robert A.; Nagaraj, Ben A.; Bruce, Robert W.

2000-01-01

The thermal conductivity of electron beam-physical vapor deposited (EB-PVD) Zr02-8wt%Y2O3 thermal barrier coatings was determined by a steady-state heat flux laser technique. Thermal conductivity change kinetics of the EB-PVD ceramic coatings were also obtained in real time, at high temperatures, under the laser high heat flux, long term test conditions. The thermal conductivity increase due to micro-pore sintering and the decrease due to coating micro-delaminations in the EB-PVD coatings were evaluated for grooved and non-grooved EB-PVD coating systems under isothermal and thermal cycling conditions. The coating failure modes under the high heat flux test conditions were also investigated. The test technique provides a viable means for obtaining coating thermal conductivity data for use in design, development, and life prediction for engine applications.

Recent advances in application of EB Technology

Energy Technology Data Exchange (ETDEWEB)

Mittendorfer, J [Mediscan GmbH, Kremsmuenster (Austria)

2001-07-01

In this paper recent advances in application of electron beam technology are presented. Important industrial and scientific achievements of the international community, together with research by Mediscan, Austria, an operator of state-of-the-art electron beam service center and innovator in the field of EB-Technology are reviewed. In addition, areas which may play an important role in the future are identified. Special focus is on the use of X-ray converters and the potential for industrial applications. (author)

Recent advances in application of EB Technology

International Nuclear Information System (INIS)

Mittendorfer, J.

2001-01-01

In this paper recent advances in application of electron beam technology are presented. Important industrial and scientific achievements of the international community, together with research by Mediscan, Austria, an operator of state-of-the-art electron beam service center and innovator in the field of EB-Technology are reviewed. In addition, areas which may play an important role in the future are identified. Special focus is on the use of X-ray converters and the potential for industrial applications. (author)

Implementation of KoHLT-EB DAQ System using compact RIO with EPICS

Energy Technology Data Exchange (ETDEWEB)

Chang, Dae-Sik; Kim, Suk-Kwon; Lee, Dong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Cho, Seungyon [National Fusion Research Institute, Daejeon (Korea, Republic of)

2016-10-15

EPICS (Experimental Physics and Industrial Control System) is a collection of software tools collaboratively developed which can be integrated to provide a comprehensive and scalable control system. Currently there is an increase in use of such systems in large Physics experiments like KSTAR, ITER and DAIC (Daejeon Accelerator Ion Complex). The Korean heat load test facility (KoHLT-EB) was installed at KAERI. This facility is utilized for a qualification test of the plasma facing component (PFC) for the ITER first wall and DEMO divertor, and the thermo-hydraulic experiments. The existing data acquisition device was Agilent 34980A multifunction switch and measurement unit and controlled by Agilent VEE. In the present paper, we report the EPICS based newly upgraded KoHLT-EB DAQ system which is the advanced data acquisition system using FPGA-based reconfigurable DAQ devices like compact RIO. The operator interface of KoHLT-EB DAQ system is composed of Control-System Studio (CSS) and another server is able to archive the related data using the standalone archive tool and the archiveviewer can retrieve that data at any time in the infra-network.

Thermal cycling behaviour of lanthanum zirconate as EB-PVD thermal barrier coating

International Nuclear Information System (INIS)

Bobzin, K.; Lugscheider, E.; Bagcivan, N.

2006-01-01

Thermal cycling tests with two different EB-PVD thermal barrier coatings (TBC) were performed in a furnace cycle test. The results of these tests showed an increase of endurable cycle number when pyrochloric La 2 Zr 2 O 7 was used as TBC. 1865 cycles were reached with La 2 Zr 2 O 7 and 1380 cycles with 7 weigth-% yttria stabilised zirconia (YSZ) EB-PVD TBC. Additional investigation was made with scanning electron microscope (SEM) to investigate morphology and to determine chemical composition by electron dispersive x-ray spectroscopy (EDS) analysis. X-Ray diffraction was performed to analyze structural constitution of deposited coatings. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

EB curing of oxidative-polymerized linseed oil

International Nuclear Information System (INIS)

Ju Xuecheng; Ha Hongfei

2000-01-01

The properties of EB curing coating films, which were determined by the structure of oxidative-polymerized linseed oil, were as following: good gloss, low hardness, better flexibility and impact resistance, low glass transition temperature and bad adhesion on tinplate. Oxidative-polymerized linseed oil could be used with other compositions not only as oligomer, but also as functional monomer to improve the properties of coating films of composite systems. Both absorbed dose sand Cobaltous naphthenate had little influence on the properties of these coating films

Mushroom bodies regulate habit formation in Drosophila.

Science.gov (United States)

Brembs, Björn

2009-08-25

To make good decisions, we evaluate past choices to guide later decisions. In most situations, we have the opportunity to simultaneously learn about both the consequences of our choice (i.e., operantly) and the stimuli associated with correct or incorrect choices (i.e., classically). Interestingly, in many species, including humans, these learning processes occasionally lead to irrational decisions. An extreme case is the habitual drug user consistently administering the drug despite the negative consequences, but we all have experience with our own, less severe habits. The standard animal model employs a combination of operant and classical learning components to bring about habit formation in rodents. After extended training, these animals will press a lever even if the outcome associated with lever-pressing is no longer desired. In this study, experiments with wild-type and transgenic flies revealed that a prominent insect neuropil, the mushroom bodies (MBs), regulates habit formation in flies by inhibiting the operant learning system when a predictive stimulus is present. This inhibition enables generalization of the classical memory and prevents premature habit formation. Extended training in wild-type flies produced a phenocopy of MB-impaired flies, such that generalization was abolished and goal-directed actions were transformed into habitual responses.

Overview of UV and EB curing

International Nuclear Information System (INIS)

Garnett, J.L.

2000-01-01

Full text: UV and EB are complementary techniques in radiation curing. In the proposed paper, a brief review of both fields will be given. This will include principles of the process, the chemistry of the systems including monomers/oligomers/polymers used, additives required where necessary such as photoinitiators for UV, flow aids, adhesion promoters and the like. The types of equipment used in such processes will also be discussed including low energy electron beam utilisation and excimer curing. The advantages and disadvantages of both techniques will be examined. Mechanistic aspects of both curing systems will be discussed. Applications of the technology including developments in the banknote printing field will be summarised

Identification of Surface Exposed Elementary Body Antigens of ...

African Journals Online (AJOL)

This study sought to identify the surface exposed antigenic components of Cowdria ruminantium elementary body (EB) by biotin labeling, determine effect of reducing and non-reducing conditions and heat on the mobility of these antigens and their reactivity to antibodies from immunized animals by Western blotting.

Swedish 18-Year-Olds' Identity Formation: Associations with Feelings about Appearance and Internalization of Body Ideals

Science.gov (United States)

Wangqvist, Maria; Frisen, Ann

2013-01-01

The aim of this study with Swedish 18-year-olds (N = 714, 55.2% women) was to investigate identity formation in relation to body-esteem and body ideal internalization. These are all important aspects of adolescents' development, but little is known about how they are related. This study indicates that late adolescents' identity formation,…

Sensitivity of the engineered barrier system (EBS) release rate to alternative conceptual models of advective release from waste packages under dripping fractures

International Nuclear Information System (INIS)

Lee, J.H.; Atkins, J.E.; McNeish, J.A.; Vallikat, V.

1996-01-01

The first model assumed that dripping water directly contacts the waste form inside the ''failed'' waste package and radionuclides are released from the EBS by advection. The second model assumed that dripping water is diverted around the package (because of corrosion products plugging the perforations), thereby being prevented from directly contacting the waste form. In the second model, radionuclides were assumed to diffuse through the perforations, and, once outside the waste package, to be released from the EBS by advection. For the case with the second EBS release model, most radionuclides had lower peak EBS release rates than with the first model. Impacts of the alternative EBS release models were greater for the radionuclides with low solubility. The analysis indicated that the EBS release model representing advection through a ''failed'' waste package (the first model) may be too conservative; thus a ''failed'' waste package container with multiple perforations may still be an important barrier to radionuclide release

Establishment of Human Neural Progenitor Cells from Human Induced Pluripotent Stem Cells with Diverse Tissue Origins

OpenAIRE

Hayato Fukusumi; Tomoko Shofuda; Yohei Bamba; Atsuyo Yamamoto; Daisuke Kanematsu; Yukako Handa; Keisuke Okita; Masaya Nakamura; Shinya Yamanaka; Hideyuki Okano; Yonehiro Kanemura

2016-01-01

Human neural progenitor cells (hNPCs) have previously been generated from limited numbers of human induced pluripotent stem cell (hiPSC) clones. Here, 21 hiPSC clones derived from human dermal fibroblasts, cord blood cells, and peripheral blood mononuclear cells were differentiated using two neural induction methods, an embryoid body (EB) formation-based method and an EB formation method using dual SMAD inhibitors (dSMADi). Our results showed that expandable hNPCs could be generated from hiPS...

Phase separation like dynamics during Myxococcus xanthus fruiting body formation

Science.gov (United States)

Liu, Guannan; Thutupalli, Shashi; Wigbers, Manon; Shaevitz, Joshua

2015-03-01

Collective motion exists in many living organisms as an advantageous strategy to help the entire group with predation, forage, and survival. However, the principles of self-organization underlying such collective motions remain unclear. During various developmental stages of the soil-dwelling bacterium, Myxococcus xanthus, different types of collective motions are observed. In particular, when starved, M. xanthus cells eventually aggregate together to form 3-dimensional structures (fruiting bodies), inside which cells sporulate in response to the stress. We study the fruiting body formation process as an out of equilibrium phase separation process. As local cell density increases, the dynamics of the aggregation M. xanthus cells switch from a spatio-temporally random process, resembling nucleation and growth, to an emergent pattern formation process similar to a spinodal decomposition. By employing high-resolution microscopy and a video analysis system, we are able to track the motion of single cells within motile collective groups, while separately tuning local cell density, cell velocity and reversal frequency, probing the multi-dimensional phase space of M. xanthus development.

Role of Ceacam1 in VEGF induced vasculogenesis of murine embryonic stem cell-derived embryoid bodies in 3D culture

Energy Technology Data Exchange (ETDEWEB)

Gu, Angel [Department of Immunology, Beckman Research Institute of the City of Hope, 1500 East Duarte Road, Duarte, CA 91010 (United States); Tsark, Walter [Department of Biology, Beckman Research Institute of the City of Hope, Duarte, CA 91010 (United States); Holmes, Kathryn V. [Department of Microbiology, University of Colorado Health Sciences, Aurora, CO 80045 (United States); Shively, John E., E-mail: jshively@coh.org [Department of Immunology, Beckman Research Institute of the City of Hope, 1500 East Duarte Road, Duarte, CA 91010 (United States)

2009-06-10

CEACAM1 (carcinoembryonic antigen-related cell adhesion molecule 1), a type I transmembrane glycoprotein involved in cell-cell adhesion has been shown to act as an angiogenic factor for mouse and human endothelial cells. Based on the ability of CEACAM1 to initiate lumen formation in human mammary epithelial cells grown in 3D culture (Matrigel), we hypothesized that murine CEACAM1 may play a similar role in vasculogenesis. In order to test this hypothesis, murine embryonic stem (ES) cells stimulated with VEGF were differentiated into embryoid bodies (EB) for 8 days (- 8-0 d) and transferred to Matrigel in the presence or absence of anti-CEACAM1 antibody for an additional 12 days (0-12 d). In the absence of anti-CEACAM1 antibody or in the presence of an isotype control antibody, the EB in Matrigel underwent extensive sprouting, generating lengthy vascular structures with well-defined lumina as demonstrated by confocal microscopy, electron microscopy, and immunohistochemical analysis. Both the length and architecture of the vascular tubes were inhibited by anti-CEACAM1 mAb CC1, a mAb that blocks the cell-cell adhesion functions of CEACAM1, thus demonstrating a critical role for this cell-cell adhesion molecule in generating and maintaining vasculogenesis. QRT-PCR analysis of the VEGF treated ES cells grown under conditions that convert them to EB revealed expression of Ceacam1 as early as - 5 to - 3 d reaching a maximum at day 0 at which time EBs were transferred to Matrigel, thereafter levels at first declined and then increased over time. Other markers of vasculogenesis including Pecam1, VE-Cad, and Tie-1 were not detected until day 0 when EBs were transferred to Matrigel followed by a steady increase in levels, indicating later roles in vasculogenesis. In contrast, Tie-2 and Flk-1 (VEGFR2) were detected on day five of EB formation reaching a maximum at day 0 on transfer to Matrigel, similar to Ceacam1, but after which Tie-2 declined over time, while Flk-1 increased

Microstructural, mechanical and oxidation features of NiCoCrAlY coating produced by plasma activated EB-PVD

International Nuclear Information System (INIS)

He, Jian; Guo, Hongbo; Peng, Hui; Gong, Shengkai

2013-01-01

NiCoCrAlY coatings produced by electron beam-physical vapor deposition (EB-PVD) have been extensively used as the oxidation resistance coatings or suitable bond coats in thermal barrier coating (TBC) system. However, the inherent imperfections caused by EB-PVD process degrade the oxidation resistance of the coatings. In the present work, NiCoCrAlY coatings were creatively produced by plasma activated electron beam-physical vapor deposition (PA EB-PVD). The novel coatings showed a terraced substructure on the surface of each grain due to the increased energy of metal ions and enhanced mobility of adatoms. Also a strong (1 1 1) crystallographic texture of γ/γ′ grains was observed. The toughness of the coatings got remarkably improved compared with the coatings deposited by conventional EB-PVD and the oxidation behavior at 1373 K showed that the novel coatings had excellent oxidation resistance. The possible mechanism was finally discussed.

Genetic Analysis of Hedgehog Signaling in Ventral Body Wall Development and the Onset of Omphalocele Formation

Science.gov (United States)

Matsumaru, Daisuke; Haraguchi, Ryuma; Miyagawa, Shinichi; Motoyama, Jun; Nakagata, Naomi; Meijlink, Frits; Yamada, Gen

2011-01-01

Background An omphalocele is one of the major ventral body wall malformations and is characterized by abnormally herniated viscera from the body trunk. It has been frequently found to be associated with other structural malformations, such as genitourinary malformations and digit abnormalities. In spite of its clinical importance, the etiology of omphalocele formation is still controversial. Hedgehog (Hh) signaling is one of the essential growth factor signaling pathways involved in the formation of the limbs and urogenital system. However, the relationship between Hh signaling and ventral body wall formation remains unclear. Methodology/Principal Findings To gain insight into the roles of Hh signaling in ventral body wall formation and its malformation, we analyzed phenotypes of mouse mutants of Sonic hedgehog (Shh), GLI-Kruppel family member 3 (Gli3) and Aristaless-like homeobox 4 (Alx4). Introduction of additional Alx4Lst mutations into the Gli3Xt/Xt background resulted in various degrees of severe omphalocele and pubic diastasis. In addition, loss of a single Shh allele restored the omphalocele and pubic symphysis of Gli3Xt/+; Alx4Lst/Lst embryos. We also observed ectopic Hh activity in the ventral body wall region of Gli3Xt/Xt embryos. Moreover, tamoxifen-inducible gain-of-function experiments to induce ectopic Hh signaling revealed Hh signal dose-dependent formation of omphaloceles. Conclusions/Significance We suggest that one of the possible causes of omphalocele and pubic diastasis is ectopically-induced Hh signaling. To our knowledge, this would be the first demonstration of the involvement of Hh signaling in ventral body wall malformation and the genetic rescue of omphalocele phenotypes. PMID:21283718

Genetic analysis of Hedgehog signaling in ventral body wall development and the onset of omphalocele formation.

Directory of Open Access Journals (Sweden)

Daisuke Matsumaru

2011-01-01

Full Text Available An omphalocele is one of the major ventral body wall malformations and is characterized by abnormally herniated viscera from the body trunk. It has been frequently found to be associated with other structural malformations, such as genitourinary malformations and digit abnormalities. In spite of its clinical importance, the etiology of omphalocele formation is still controversial. Hedgehog (Hh signaling is one of the essential growth factor signaling pathways involved in the formation of the limbs and urogenital system. However, the relationship between Hh signaling and ventral body wall formation remains unclear.To gain insight into the roles of Hh signaling in ventral body wall formation and its malformation, we analyzed phenotypes of mouse mutants of Sonic hedgehog (Shh, GLI-Kruppel family member 3 (Gli3 and Aristaless-like homeobox 4 (Alx4. Introduction of additional Alx4(Lst mutations into the Gli3(Xt/Xt background resulted in various degrees of severe omphalocele and pubic diastasis. In addition, loss of a single Shh allele restored the omphalocele and pubic symphysis of Gli3(Xt/+; Alx4(Lst/Lst embryos. We also observed ectopic Hh activity in the ventral body wall region of Gli3(Xt/Xt embryos. Moreover, tamoxifen-inducible gain-of-function experiments to induce ectopic Hh signaling revealed Hh signal dose-dependent formation of omphaloceles.We suggest that one of the possible causes of omphalocele and pubic diastasis is ectopically-induced Hh signaling. To our knowledge, this would be the first demonstration of the involvement of Hh signaling in ventral body wall malformation and the genetic rescue of omphalocele phenotypes.

76 FR 1192 - Notice of a Change in Status of an Extended Benefit (EB) Period for Puerto Rico

Science.gov (United States)

2011-01-07

... Extended Benefit (EB) Period for Puerto Rico AGENCY: Employment and Training Administration, Labor. ACTION... Puerto Rico. The following change has occurred since the publication of the last notice regarding the State's EB status: Puerto Rico's 13-week IUR has fallen below the 6% threshold and does not equal or...

Sintering and microstructure evolution of columnar nickel-based superalloy sheets prepared by EB-PVD

International Nuclear Information System (INIS)

Chen, S.; Qu, S.J.; Liang, J.; Han, J.C.

2010-01-01

Research highlights: → EB-PVD technology is commonly used to deposit thermal barrier coatings (TBCs) and columnar structure is commonly seen in EB-PVD condensates. The unique columnar structure can provide outstanding resistance against thermal shock and mechanical strains for TBCs. However, a number of researchers have found that the columnar structure can affect the mechanical properties of EB-PVD alloy thin sheet significantly. As yet, works on how to reduce this kind of effects are seldom done. In the present article, we tried to reveal the sintering effects on microstructure evolution and mechanical properties of columnar Ni-based superalloy sheet. The results suggests that after sintering, the columnar structure degrades. Degradation depends on sintering temperature and time. Both the ultimate tensile strength and the elongation percentage are effectively improved after sintering. - Abstract: A ∼0.15 mm-thick columnar nickel-based superalloy sheet was obtained by electron beam physical vapor deposition (EB-PVD). The as-deposited alloy sheet was sintered at different conditions. The microstructure of the specimens before and after sintering was characterized by using scanning electron microscopy. An X'Pert texture facility was used to determine the crystallographic orientation of the as-deposited alloy sheet. The phase transformation was investigated by X-ray diffraction. Tensile tests were conducted at room temperature on as-deposited and sintered specimens. The results show that the as-deposited sheet is composed of typical columnar structures. After sintering, however, the columnar structure degrades. The degradation depends on sintering temperature and time. Both the ultimate tensile strength and the elongation percentage are effectively improved after sintering.

Creep properties of EB welded copper overpack at 125-175 deg C

International Nuclear Information System (INIS)

Holmstroem, S.; Salonen, J.; Kinnunen, T.

2012-01-01

Electron Beam welds (EBW) chosen as primary sealing method by Posiva welding the over-pack canister lids of oxygen-free phosphorus micro-alloyed copper (OFP) have been tested for material properties relevant to long term creep life prediction. Creep rupture results are presented for the ruptured 175 deg C tests and for the ongoing long term tests at 150 deg C and 125 deg C. The current status (test time, creep strain and strain rate) of the ongoing tests are reported. The initial (175 deg C) results indicate that the EB welds are weaker than the parent material and that both round bar and spark eroded square test specimens produce weld strengths of about 0.75 at tests durations of 5000 h. The downward trend is however expected to continue for the longer test durations. The creep ductility shows decrease for the longer tests. Life estimates for the EB weld have been calculated at 100 deg C for both 50 and 80 MPa with the so far lowest measured EB weld strength factor (WSF=0.77). The state-of-the-art model on the available data give estimated lives of 21000 and 3000 years correspondingly. However, simulated to the expected temperature profile of the repository service the life fraction reached after 10000 years of service is 1 % and 7 % for the same stress levels. It is though important to remembered that the 80 MPa assumption is very conservative in nature and that the predictions do not take into account relaxation of stresses, further decline of the WSF or anisotropy of the weld and are therefore still to be considered indicative only. It is also to be remembered that there is only limited data in the long term regime for the weldments and that the estimates are based on the few EB data available in the public domain added with the Posiva data of this project. Improvement of the models and predictions are expected from the ongoing 125 deg C and 150 deg C long term tests. (orig.)

NiCoCrAl/YSZ laminate composites fabricated by EB-PVD

International Nuclear Information System (INIS)

Shi Guodong; Wang Zhi; Liang Jun; Wu Zhanjun

2011-01-01

Highlights: → The metal-ceramic laminate composites were fabricated by EB-PVD. → Both metal and ceramic layers consisted of straight columns with banded structures. → Columnar grain size was limited by the periodic layer interfaces in the laminates. → Effect of columns on fracture property was decreased by limiting layer thickness. → Laminates showed greater specific strength than monolithic metal foil. - Abstract: Two NiCoCrAl/YSZ laminate composites (A and B) with different metal-layer thickness (∼35 μm and 14 μm, respectively) were fabricated by electron beam physical vapor deposition (EB-PVD). Their microstructure was examined and their mechanical properties were compared with the 289 μm thick NiCoCrAl monolithic foil produced by EB-PVD. Both the YSZ and NiCoCrAl layers of the laminate composites had columnar grain structure. But the periodic layer interfaces limited the columnar grain size. Some pores between the columns were also observed. It was found that the strength of the laminate A was equal approximately to that of the NiCoCrAl monolithic foil, and that laminate B had the greater strength. Moreover, the density of the foils decreased with the increasing thickness ratio of YSZ/NiCoCrAl layers and the increasing the layer number. Thus, comparing with the NiCoCrAl monolithic foil, the NiCoCrAl/YSZ laminate composites not only had the equal or greater strength, but also had the much greater specific strength.

Radiosynoviorthesis in the reflection of Evidence-based Medicine (EbM)

International Nuclear Information System (INIS)

Kampen, W.U.

2006-01-01

This paper summarizes the literature on clinical efficacy of radiosynoviorthesis with respect to the criteria of evidence-based medicine (EbM). Each therapy has to face up to the success and the costs of other treatment modalities, especially in times of scarce financial resources of our health care system. For many physicians and scientists, evidence-based medicine, which means weighting clinical trials by several quality factors like randomization, blinding or comparison with a placebo seems to be the ''philosophers'stone'' to some extent. Concerning radiosynoviorthesis, the existence of clinical studies with a high quality according to the EbM is sometimes negated. However, this statement cannot be abided after extensive revision of the literature. The nuclear medicine physician practising radiosynoviorthesis should be provided with arguments from the literature supporting his personal experience for successful discussions with referring colleques. This is achieved by listing the respective papers especially of evidence classes Ib and IIa with a short summary of each of them. Some critical remarks on evidence-based medicine if used as the only basis of therapeutic practise complete this paper. (orig.)

Primary study on synthesis and characterization of the new type EB curable resins. Pt.1: Acrylic resins modified by light-oil

International Nuclear Information System (INIS)

Wei Jinshan; Yi Min; Wang Ruiyu; Li Jun; Ha Hongfei

1995-01-01

An acrylic resin modified by vegetable oil with high degree of unsaturation level has been synthesized. The characterization of coating film EB cured by the modified acrylic resin was studied primarily. The new type of EB curable acrylic resin is possessed of many merits such as cheap raw materials, simple synthesis technique and pretty characteristics of coating film. It is especially fit for timber surface coatings cured by EB radiation

Effect of perfluorooctane sulfonate on pluripotency and differentiation factors in mouse embryoid bodies

International Nuclear Information System (INIS)

Xu, Bo; Ji, Xiaoli; Chen, Xiaojiao; Yao, Mengmeng; Han, Xiumei; Chen, Minjian; Tang, Wei; Xia, Yankai

2015-01-01

Perfluorooctane sulfonate (PFOS) poses potential risks to early development, but the molecular mechanisms how PFOS affects embryonic development are still unclear. Mouse embryoid bodies (mEBs) provide ideal models for testing safety or toxicity of chemicals in vitro. In this study, mEBs were exposed to PFOS up to 6 days and then their pluripotency and differentiation markers were evaluated. Our data showed that the mRNA and protein levels of pluripotency markers (Oct4, Sox2, Nanog) in mEBs were significantly increased following exposure to PFOS. Meanwhile, the expressions of miR-134, miR-145, miR-490-3p were decreased accordingly. PFOS reduced the mRNA levels of endodermal markers (Sox17, FOXA2), mesodermal markers (SMA, Brachyury) and ectodermal markers (Nestin, Fgf5) in mEBs. Meanwhile, PFOS increased the mRNA and protein levels of polycomb group (PcG) family members (Cbx4, Cbx7, Ezh2). Overall, our results showed that PFOS could increase the expression levels of pluripotency factors and decrease the differentiation markers

EBS/C proton spectra from a virgin diamond crystal

Energy Technology Data Exchange (ETDEWEB)

Erich, M., E-mail: marko.erich@gmail.com [Laboratory of Physics, Vinča Institute of Nuclear Sciences, University of Belgrade, PO Box 552, Belgrade (Serbia); Kokkoris, M. [Department of Physics, National Technical University of Athens, Zografou Campus 157 80, Athens (Greece); Fazinić, S. [Laboratory for Ion Beam Interactions, Department of Experimental Physics, Institute Ruđer Bošković, Bijenička cesta 54, 10000 Zagreb (Croatia); Petrović, S. [Laboratory of Physics, Vinča Institute of Nuclear Sciences, University of Belgrade, PO Box 552, Belgrade (Serbia)

2016-08-15

In the present work, elastic backscattering channeling spectra, EBS/C, of protons in a 〈1 0 0〉 diamond crystal were experimentally and theoretically studied via a new computer simulation code. Proton incident energies for EBS/C spectra were in the energy range from 1.0 MeV to 1.9 MeV. The energy range was chosen in order to explore a distinct strong resonance of the {sup 12}C(p,p{sub 0}){sup 12}C elastic scattering at 1737 keV. The computer simulation code applied for the fitting of the experimental spectra in the random mode was compared with the corresponding SIMNRA results. In the channeling mode, it assumes a Gompertz type sigmoidal dechanneling function, which has two fitting parameters, x{sub c} and k, the dechanneling range and rate, respectively. It also uses α, ratio of the channeling to random energy losses, as a fitting parameter. It was observed that x{sub c} increases, k decreases and α stays relatively constant with the proton incident energy. These observations confirm the physical interpretation of the fitting parameters. Also, they constitute the basics for the further development of the code for the quantification of induced amorphization and depth profiling of implanted ions.

EB-promoted recycling of waste tire rubber with polyolefins

International Nuclear Information System (INIS)

Mészáros, László; Bárány, Tamás; Czvikovszky, Tibor

2012-01-01

Despite the fact that more and more methods and solutions are used in the recycling of polymers, there are still some problems, especially in the recycling of cross-linked materials such as rubber. Usually the biggest problem is the lack of compatibility between the cross-linked rubber and the thermoplastic matrix. In this study we applied ground tire rubber (GTR) as recycled material. The GTR was embedded into polyethylene (PE) and polyethylene/ethylene-vinyl acetate copolymer (PE/EVA) matrices. In order to increase the compatibility of the components electron beam (EB) irradiation was applied. The results showed that the irradiation has a beneficial effect on the polymer–GTR interfacial connection. The EB treatment increased not only the tensile strength but also the elongation at break. The irradiation had also positive effect on the impact strength properties. - Highlights: ► In this study ground tire rubber was incorporated into polyethylene (LDPE) matrix. ► Compatibilizing effects of irradiation and ethylene-vinyl acetate were investigated. ► The samples were manufactured by twin-screw extrusion and injection molding. ► Both compatibilizing methods improved the rubber-like properties of the blends. ► This improvement was especially significant when they were applied together.

EB curable wetting resins for magnetic media coatings

International Nuclear Information System (INIS)

Laskin, L.; Ansel, R.E.; Murray, K.P.; Schmid, S.R.

1984-01-01

The magnetic media industry is studying means to improve the recording density, durability, product uniformity and production efficiency and to reduce wetting agent migration in the magnetic film. The use of electron beam curable resin binders for magnetic coatings is one of the approaches being studied for this. This paper compares the wetting efficiencies of several electron beam curable systems with a conventional resin and a conventional wetting agent. In this study it has been demonstrated that EB resins can be designed to effect proper magnetic pigment dispersion

Potential for radionuclide immobilization in the EBS/NFE: solubility limiting phases for neptunium, plutonium, and uranium

Energy Technology Data Exchange (ETDEWEB)

Rard, J. A., LLNL

1997-10-01

Retardation and dispersion in the far field of radionuclides released from the engineered barrier system/near field environment (EBS/NFE) may not be sufficient to prevent regulatory limits being exceeded at the accessible environment. Hence, a greater emphasis must be placed on retardation and/or immobilization of radionuclides in the EBS/NFE. The present document represents a survey of radionuclide-bearing solid phases that could potentially form in the EBS/NFE and immobilize radionuclides released from the waste package and significantly reduce the source term. A detailed literature search was undertaken for experimental solubilities of the oxides, hydroxides, and various salts of neptunium, plutonium, and uranium in aqueous solutions as functions of pH, temperature, and the concentrations of added electrolytes. Numerous solubility studies and reviews were identified and copies of most of the articles were acquired. However, this project was only two months in duration, and copies of some the identified solubility studies could not be obtained at short notice. The results of this survey are intended to be used to assess whether a more detailed study of identified low- solubility phase(s) is warranted, and not as a data base suitable for predicting radionuclide solubility. The results of this survey may also prove useful in a preliminary evaluation of the efficacy of incorporating chemical additives to the EBS/NFE that will enhance radionuclide immobilization.

Mainstreaming Ecosystem Services Based Climate Change Adaptation (EbA in Bangladesh: Status, Challenges and Opportunities

Directory of Open Access Journals (Sweden)

Nazmul Huq

2017-06-01

Full Text Available The paper aims to analyze the extent of Ecosystem Service (ESS based Adaptation (EbA to climate change in the policy-making process of Bangladesh. The paper is based on a three stage hybrid policy-making cycle: (i agenda setting; (ii policy formulation; and (iii policy implementation stage, where the contributions of EbA can horizontally (on the ground or vertically (strategic stage be mainstreamed and integrated. A total of nine national and sectoral development and climate change policies, and 329 climate change adaptation projects are examined belonging to different policy-making stages. The major findings include that the role of ESS is marginally considered as an adaptation component in most of the reviewed policies, especially at the top strategic level (vertical mainstreaming. However, at the policy formulation and implementation stage (horizontal mainstreaming, they are largely ignored and priority is given to structural adaptation policies and projects, e.g., large scale concrete dams and embankments. For example, ESS’s roles to adapt sectors such as urban planning, biodiversity management and disaster risk reduction are left unchecked, and the implementation stage receives overwhelming priorities and investments to undertake hard adaptation measures such that only 38 projects are related to EbA. The paper argues that: (i dominant structural adaptation ideologies; (ii the expert and bureaucracy dependent policy making process; and (iii the lack of adaptive and integration capacities at institutional level are considerably offsetting the EbA mainstreaming process that need to be adequately addressed for climate change adaptation.

Suitable configurations for triangular formation flying about collinear libration points under the circular and elliptic restricted three-body problems

Science.gov (United States)

Ferrari, Fabio; Lavagna, Michèle

2018-06-01

The design of formations of spacecraft in a three-body environment represents one of the most promising challenges for future space missions. Two or more cooperating spacecraft can greatly answer some very complex mission goals, not achievable by a single spacecraft. The dynamical properties of a low acceleration environment such as the vicinity of libration points associated to a three-body system, can be effectively exploited to design spacecraft configurations able of satisfying tight relative position and velocity requirements. This work studies the evolution of an uncontrolled formation orbiting in the proximity of periodic orbits about collinear libration points under the Circular and Elliptic Restricted Three-Body Problems. A three spacecraft triangularly-shaped formation is assumed as a representative geometry to be investigated. The study identifies initial configurations that provide good performance in terms of formation keeping, and investigates key parameters that control the relative dynamics between the spacecraft within the three-body system. Formation keeping performance is quantified by monitoring shape and size changes of the triangular formation. The analysis has been performed under five degrees of freedom to define the geometry, the orientation and the location of the triangle in the synodic rotating frame.

Comparison of Cell Viability and Embryoid Body Size of Two Embryonic Stem Cell Lines After Different Exposure Times to Bone Morphogenetic Protein 4

Directory of Open Access Journals (Sweden)

Nehleh Zarei Fard

2015-03-01

Full Text Available Background: Activation of bone morphogenetic protein 4 (BMP4 signaling pathway in embryonic stem (ES cells plays an important role in controlling cell proliferation, differentiation, and apoptosis. Adverse effects of BMP4 occur in a time dependent manner; however, little is known about the effect of different time exposure of this growth factor on cell number in culture media. In this study, we investigated the role of two different exposure times to BMP4 in cell viability, embryoid body (EB, size, and cavitation of ES cells. Methods: Embryonic stem cells (R1 and B1 lines were released from the feeder cell layers and were cultured using EBs protocol by using the hanging drop method and monolayer culture system. The cells were cultured for 5 days with 100 ng/mL BMP4 from the beginning (++BMP4 or after 48 h (+BMP4 of culture and their cell number were counted by trypan blue staining. The data were analyzed using non-parametric two-tailed Mann-Whitney test. P<0.05 was considered as significant. Results: In EB culture protocol, cell number significantly decreased in +BMP4 culture condition with greater cavity size compared to the ++BMP4 condition at day 5 (P=0.009. In contrast, in monolayer culture system, there was no significant difference in the cell number between all groups (P=0.91. Conclusion: The results suggest that short-term exposure of BMP4 is required to promote cavitation in EBs according to lower cell number in +BMP4 condition. Different cell lines showed different behavior in cavitation formation.

Granules Harboring Translationally Active mRNAs Provide a Platform for P-Body Formation following Stress

Directory of Open Access Journals (Sweden)

Jennifer Lui

2014-11-01

Full Text Available The localization of mRNA to defined cytoplasmic sites in eukaryotic cells not only allows localized protein production but also determines the fate of mRNAs. For instance, translationally repressed mRNAs localize to P-bodies and stress granules where their decay and storage, respectively, are directed. Here, we find that several mRNAs are localized to granules in unstressed, actively growing cells. These granules play a key role in the stress-dependent formation of P-bodies. Specific glycolytic mRNAs are colocalized in multiple granules per cell, which aggregate during P-body formation. Such aggregation is still observed under conditions or in mutants where P-bodies do not form. In unstressed cells, the mRNA granules appear associated with active translation; this might enable a coregulation of protein expression from the same pathways or complexes. Parallels can be drawn between this coregulation and the advantage of operons in prokaryotic systems.

Primary study on synthesis and characterization of the new type EB curable resins. Pt.2: Alkyd resins modified by LFA

International Nuclear Information System (INIS)

Yi Min; Wei Jinshan; Li Jun; Wang Ruiyu; Ha Hongfei

1995-01-01

The authors have synthesized a new type of EB curable resin by using oil fatty acid. The preparation method of coating and the performance of EB curing coating film were described. The synthesis process has been simplified and the price of the raw materials was lower

Engineered barrier systems (EBS): design requirements and constraints

International Nuclear Information System (INIS)

2004-01-01

A joint NEA-EC workshop entitled 'Engineered Barrier Systems: Design Requirements and Constraints' was organised in Turku, Finland on 26-29 August 2003 and hosted by Posiva Oy. The main objectives of the workshop were to promote interaction and collaboration among experts responsible for engineering design and safety assessment in order to develop a greater understanding of how to achieve the integration needed for the successful design of engineered barrier systems, and to clarify the role that an EBS can play in the overall safety case for a repository. These proceedings present the outcomes of this workshop. (author)

ZZ BOREHOLE-EB6.8-MG, multi group cross-section library for deterministic and Monte Carlo codes

International Nuclear Information System (INIS)

Kodeli, Ivo; Aldama, Daniel L.; Leege, Piet F.A. de; Legrady, David; Hoogenboom, J. Eduard

2007-01-01

1 - Description: Format: MATXS and ACE; Number of groups: 175 neutron, 45 gamma-ray; Nuclides: H-1, C-12, O-16, Na-23, Mg-nat, Al-27, Si-28, -29, -30, S-nat, Cl-35, -37, K-nat, Ca-nat, Mn-55, Fe-54, -56, -57, -58, I-127, W-nat. Origin: ENDF/B-VI.8; Weighting spectrum: Fission and fusion peak at high energies and a 1/E + thermal Maxwellian extension at low energies. The following materials/nuclides are included in the library: H-1, C-12, O-16, Na-23, Mg-nat, Al-27, Si-28, -29, -30, S-nat, Cl-35, -37, K-nat, Ca-nat, Fe-54, -56, -57, -58, Mn-55, I-127, W-nat. ZZ-BOREHOLE-EB6.8-MG is a multigroup cross section library for deterministic (DOORS, DANTSYS) and Monte Carlo (MCNP) transport codes developed for the oil well logging applications. The library is based on the ENDF/B-VI.8 evaluation and was processed by the NJOY-99 code. The cross sections are given in the 175 neutron and 45 gamma ray group structure. The MATXS format library can be directly used in TRANSX code to prepare the multigroup self-shielded cross sections for deterministic discrete ordinates codes like DOORS and DANTSYS. The data provided in the GROUPR and GAMINR format were converted to the MCNP ACE format by the NSLINK, SCALE and CRSRD codes. IAEA1398/03: Multigroup cross section data for Mn-55 were added in TRANSX format

Polyurethane acrylate networks including cellulose nanocrystals: a comparison between UV and EB- curing

Science.gov (United States)

Furtak-Wrona, K.; Kozik-Ostrówka, P.; Jadwiszczak, K.; Maigret, J. E.; Aguié-Béghin, V.; Coqueret, X.

2018-01-01

A water-based polyurethane (PUR) acrylate water emulsion was selected as a radiation curable matrix for preparing nanocomposites including cellulose nanocrystals (CNC) prepared by controlled hydrolysis of Ramie fibers. Cross-linking polymerization of samples prepared in the form of films or of 1 mm-thick bars was either initiated by exposure to the 395 nm light of a high intensity LED lamp or by treatment with low energy electron beam (EB). The conversion level of acrylate functions in samples submitted to increasing radiation doses was monitored by Fourier Transform Infrared Spectroscopy (FTIR). Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) were used to characterize changes in the glass transition temperature of the PUR-CNC nanocomposites as a function of acrylate conversion and of CNC content. Micromechanical testing indicates the positive effect of 1 wt% CNC on Young's modulus and on the tensile strength at break (σ) of cured nanocomposites. The presence of CNC in the PUR acrylate matrix was shown to double the σ value of the nanocomposite cured to an acrylate conversion level of 85% by treatment with a 25 kGy dose under EB, whereas no increase of σ was observed in UV-cured samples exhibiting the same acrylate conversion level. The occurrence of grafting reactions inducing covalent linkages between the polysaccharide nanofiller and the PUR acrylate matrix during the EB treatment is advanced as an explanation to account for the improvement observed in samples cured under ionizing radiation.

Tailoring the structure and properties of amorphous starch blending and EB-radiation processing

International Nuclear Information System (INIS)

Khandal, D.; Bliard, C.; Coqueret, X.; Mikus, P.Y.; Dole, P.; Baumberger, S.

2011-01-01

Complete text of publication follows. Starch can be used alone and in combination with other compounds to make biodegradable articles from renewable resources. Lignins and their derivatives are good candidates for limiting the water sensitivity of starch-based materials, but they exhibit poor compatibility in blends with polysaccharides. Electron beam (EB) processing is proposed as an efficient method for inducing covalent linkages between the two constituents. Compared to unirradiated starting materials, the surface and bulk properties of EB-irradiated starch - lignin blends submitted to EB irradiation showed an interesting reduction in hydrophilicity. Radiation induced grafting of lignin models onto starch was shown to impede long-term retrogradation, with limited loss of mechanical properties. The reactivity under radiation of model blends was examined by several analytical methods. Maldi-T of mass spectrometry allowed us to propose reasonable free radical mechanisms that account for the grafting of various benzyl and cinnamyl alcohols onto maltodextrins. The presence of cinnamyl derivatives was found not only to limit degradation, but also modify the properties of the formulations (improved hydrophobicity, mechanical properties). Size exclusion chromatography and gel fraction measurements confirmed unambiguously the attachment of UV-absorbing chromophores onto the maltodextrin main chain. The combination of the obtained results demonstrates the possibility of altering in a favourable way the tensile properties of plasticized starch by applying high energy radiation to properly formulated blends including aromatic compounds like cinnamyl alcohol.

Particle Number Dependence of the N-body Simulations of Moon Formation

Science.gov (United States)

Sasaki, Takanori; Hosono, Natsuki

2018-04-01

The formation of the Moon from the circumterrestrial disk has been investigated by using N-body simulations with the number N of particles limited from 104 to 105. We develop an N-body simulation code on multiple Pezy-SC processors and deploy Framework for Developing Particle Simulators to deal with large number of particles. We execute several high- and extra-high-resolution N-body simulations of lunar accretion from a circumterrestrial disk of debris generated by a giant impact on Earth. The number of particles is up to 107, in which 1 particle corresponds to a 10 km sized satellitesimal. We find that the spiral structures inside the Roche limit radius differ between low-resolution simulations (N ≤ 105) and high-resolution simulations (N ≥ 106). According to this difference, angular momentum fluxes, which determine the accretion timescale of the Moon also depend on the numerical resolution.

Outstanding diversity of heritage features in large geological bodies: The Gachsaran Formation in southwest Iran

Science.gov (United States)

Habibi, Tahereh; Ruban, Dmitry A.

2017-09-01

The ideas of geological heritage and geological diversity have become very popular in the modern science. These are usually applied to geological domains or countries, provinces, districts, etc. Additionally, it appears to be sensible to assess heritage value of geological bodies. The review of the available knowledge and the field investigation of the Gachsaran Formation (lower Miocene) in southwest Iran permit to assign its features and the relevant phenomena to as much as 10 geological heritage types, namely stratigraphical, sedimentary, palaeontological, palaeogeographical, geomorphological, hydrogeological, engineering, structural, economical, and geohistorical types. The outstanding diversity of the features of this formation determines its high heritage value and the national rank. The geological heritage of the Gachsaran Formation is important to scientists, educators, and tourists. The Papoon and Abolhaiat sections of this formation are potential geological heritage sites, although these do not represent all above-mentioned types. The large territory, where the Gachsaran Formation outcrop, has a significant geoconservation and geotourism potential, and further inventory of geosites on this territory is necessary. Similar studies of geological bodies in North Africa and the Middle East can facilitate better understanding of the geological heritage of this vast territory.

A microstructural study of F82H-MOD. Plate, powder HIP and EB and TIG weldments

International Nuclear Information System (INIS)

Schuring, E.W.

1998-06-01

F82H is the heat identification number of a ferritic/martensitic steel. The steel has a chemical composition resulting in low activation after neutron irradiation. At ECN a microstructural study was conducted on plates of F82H (73, 15 and 25mm thick), a bar of HIPped F82H and EB and TIG welds in F82H plates. The investigation was aimed to characterise the microstructures for reference in irradiation experiments. The F82H mod. plates have a martensitic matrix with carbide precipitation on the prior austenite grain boundaries and the martensite laths. The carbide precipitation is most pronounced on the prior austenite grain boundaries. The PAG is comparable for the three plate thicknesses investigated. In two plates faint segregation bands were found with a denser carbide precipitation and 8-ferrite. Further Ta, Ti and Zr containing oxides are present. Hardness measurements show a higher overall hardness in the 25mm plate investigated compared to the 7.5 and 15mm plates. The F82H HIP bar shows a homogeneous PAG throughout the diameter. The microstructure shows a zone starting at about 1 mm below the surface with a width of 14mm, with a relatively high concentration of low precipitation density ferritic like fields, which corresponds to a zone with a 15HV5 lower hardness with respect to the rest of the bar. This zone is expected to be related to the HIP process. Further in the microstructure a circular pattern of W and Ta enriched inclusions is found, which mark the original HIP-powder grain boundaries. The EB-welds were manufactured by two manufactures and differ mostly in the heat input, resulting in differences in HAZ-width and the width of the weld cap. The F82H EB welds show comparable microstructures in the weld pool, with a martensitic microstructure free of carbides. All EB-welds contain 8-ferrite in concentrations of 0.1-1%. In the heat affected zone (HAZ), the coarse grained HAZ (CGHAZ) is free of carbide precipitation, whereas the fine grained HAZ (FGHAZ

S. pombe CLASP needs dynein, not EB1 or CLIP170, to induce microtubule instability and slows polymerization rates at cell tips in a dynein-dependent manner

Science.gov (United States)

Grallert, Agnes; Beuter, Christoph; Craven, Rachel A.; Bagley, Steve; Wilks, Deepti; Fleig, Ursula; Hagan, Iain M.

2006-01-01

The Schizosaccharomyces pombe CLIP170-associated protein (CLASP) Peg1 was identified in a screen for mutants with spindle formation defects and a screen for molecules that antagonized EB1 function. The conditional peg1.1 mutant enabled us to identify key features of Peg1 function. First, Peg1 was required to form a spindle and astral microtubules, yet destabilized interphase microtubules. Second, Peg1 was required to slow the polymerization rate of interphase microtubules that establish end-on contact with the cortex at cell tips. Third, Peg1 antagonized the action of S. pombe CLIP170 (Tip1) and EB1 (Mal3). Fourth, although Peg1 resembled higher eukaryotic CLASPs by physically associating with both Mal3 and Tip1, neither Tip1 nor Mal3 was required for Peg1 to destabilize interphase microtubules or for it to associate with microtubules. Conversely, neither Mal3 nor Tip1 required Peg1 to associate with microtubules or cell tips. Consistently, while mal3.Δ and tip1.Δ disrupted linear growth, corrupting peg1 + did not. Fifth, peg1.1 phenotypes resembled those arising from deletion of the single heavy or both light chains of fission yeast dynein. Furthermore, all interphase phenotypes arising from peg1 + manipulation relied on dynein function. Thus, the impact of S. pombe CLASP on interphase microtubule behavior is more closely aligned to dynein than EB1 or CLIP170. PMID:16951255

Predicting hydrocarbon potential of an earth formation underlying a body of water

International Nuclear Information System (INIS)

Kaplan, I.R.; Demaison, G.J.

1983-01-01

A method for the on-site collection and examination of small concentrations of methane dissolved in water so as to predict hydrocarbon potential of an earth formation underlying a body of water, said formation being a source of said methane, comprises: (i) sampling the water; (ii) continuously vacuum separating said water into liquid and gas phases; (iii) quantitatively separating interfering gas species from methane; (iv) quantitatively oxidising said methane; (v) cryogenically trapping the resulting gaseous carbon dioxide and water vapor at a trapping station, and (vi) isotopically examining said trapped carbon dioxide and water vapour for carbon and deuterium distribution. (author)

Low nuclear body formation and tax SUMOylation do not prevent NF-kappaB promoter activation

Directory of Open Access Journals (Sweden)

Bonnet Amandine

2012-09-01

Full Text Available Abstract Background The Tax protein encoded by Human T-lymphotropic virus type 1 (HTLV-1 is a powerful activator of the NF-κB pathway, a property critical for HTLV-1-induced immortalization of CD4+ T lymphocytes. Tax permanently stimulates this pathway at a cytoplasmic level by activating the IκB kinase (IKK complex and at a nuclear level by enhancing the binding of the NF-κB factor RelA to its cognate promoters and by forming nuclear bodies, believed to represent transcriptionally active structures. In previous studies, we reported that Tax ubiquitination and SUMOylation play a critical role in Tax localization and NF-κB activation. Indeed, analysis of lysine Tax mutants fused or not to ubiquitin or SUMO led us to propose a two-step model in which Tax ubiquitination first intervenes to activate IKK while Tax SUMOylation is subsequently required for promoter activation within Tax nuclear bodies. However, recent studies showing that ubiquitin or SUMO can modulate Tax activities in either the nucleus or the cytoplasm and that SUMOylated Tax can serve as substrate for ubiquitination suggested that Tax ubiquitination and SUMOylation may mediate redundant rather than successive functions. Results In this study, we analyzed the properties of a new Tax mutant that is properly ubiquitinated, but defective for both nuclear body formation and SUMOylation. We report that reducing Tax SUMOylation and nuclear body formation do not alter the ability of Tax to activate IKK, induce RelA nuclear translocation, and trigger gene expression from a NF-κB promoter. Importantly, potent NF-κB promoter activation by Tax despite low SUMOylation and nuclear body formation is also observed in T cells, including CD4+ primary T lymphocytes. Moreover, we show that Tax nuclear bodies are hardly observed in HTLV-1-infected T cells. Finally, we provide direct evidence that the degree of NF-κB activation by Tax correlates with the level of Tax ubiquitination, but not

Low nuclear body formation and tax SUMOylation do not prevent NF-kappaB promoter activation.

Science.gov (United States)

Bonnet, Amandine; Randrianarison-Huetz, Voahangy; Nzounza, Patrycja; Nedelec, Martine; Chazal, Maxime; Waast, Laetitia; Pene, Sabrina; Bazarbachi, Ali; Mahieux, Renaud; Bénit, Laurence; Pique, Claudine

2012-09-25

The Tax protein encoded by Human T-lymphotropic virus type 1 (HTLV-1) is a powerful activator of the NF-κB pathway, a property critical for HTLV-1-induced immortalization of CD4⁺ T lymphocytes. Tax permanently stimulates this pathway at a cytoplasmic level by activating the IκB kinase (IKK) complex and at a nuclear level by enhancing the binding of the NF-κB factor RelA to its cognate promoters and by forming nuclear bodies, believed to represent transcriptionally active structures. In previous studies, we reported that Tax ubiquitination and SUMOylation play a critical role in Tax localization and NF-κB activation. Indeed, analysis of lysine Tax mutants fused or not to ubiquitin or SUMO led us to propose a two-step model in which Tax ubiquitination first intervenes to activate IKK while Tax SUMOylation is subsequently required for promoter activation within Tax nuclear bodies. However, recent studies showing that ubiquitin or SUMO can modulate Tax activities in either the nucleus or the cytoplasm and that SUMOylated Tax can serve as substrate for ubiquitination suggested that Tax ubiquitination and SUMOylation may mediate redundant rather than successive functions. In this study, we analyzed the properties of a new Tax mutant that is properly ubiquitinated, but defective for both nuclear body formation and SUMOylation. We report that reducing Tax SUMOylation and nuclear body formation do not alter the ability of Tax to activate IKK, induce RelA nuclear translocation, and trigger gene expression from a NF-κB promoter. Importantly, potent NF-κB promoter activation by Tax despite low SUMOylation and nuclear body formation is also observed in T cells, including CD4⁺ primary T lymphocytes. Moreover, we show that Tax nuclear bodies are hardly observed in HTLV-1-infected T cells. Finally, we provide direct evidence that the degree of NF-κB activation by Tax correlates with the level of Tax ubiquitination, but not SUMOylation. These data reveal that the

optical properties and morphological structure of Eb-Irradiated LDPE / P P Blends

International Nuclear Information System (INIS)

Ali, Z.I.; Said, H.M.; Youssef, H.A.; Saleh, H.H.; Abdel Monem, N.M.

2004-01-01

Blending is an effective method for improving the physical and chemical properties of homopolymers. however, the problem of phase separation often in some polymer blends occurs due to incompatibility of homopolymer which impairs the expected physico- chemical properties of blends. in this study , isotactic polypropylene, (P P), was blended with low density polyethylene, (LDPE), in the presence of various ratios of polyfunctional monomer, (PFM), namely trimethylol propane trimethacrylate, (TMPTMA), as a crosslinking and/or compatibilizing agents. the electron beam irradiation of the investigated LDPE/PP blends was carried out at different irradiation doses up to 50 kGy to improve the compatibility of LDPE/PP blends. the dye affinity of disperse and basic dyes in LDPE, PP and LDPE/PP blends was investigated in terms of color strength and visible absorbance intensities. in addition, the microstructures of the investigated samples have been studied and it is considered as an indication of the compatibility of LDPE/PP blend. the results show that the unmodified and modified LDPE samples exhibit the highest values of both color strength and visible absorbance intensities compared with unmodified and modified PP samples. also the intensities of these values in the LDPE/PP blends decrease as the PP content increases in the blend . in addition, the increase of EB irradiation dose and PFM ratios leads to an increase in the values of color strength and visible absorbance intensities. moreover, the affinity of all investigated samples towards disperse dye is being more pronounced than the basic dye. the interfacial adhesion of LDPE/PP blend could be enhanced by adding crosslinking agent, (TMPTMA), and EB irradiation process with different irradiation doses. the obtained data for the microstructures of all the investigated samples support that the EB irradiation beside the incorporation of PEM into the homopolymer matrix remarkably improve the compatibility of the polymer blend

Properties of TEM standing waves with E||B

Science.gov (United States)

Zaghloul, H.; Buckmaster, H. A.

This paper summarizes the known properties of E∥B TEM standing waves and shows that for such waves (i) E and B cannot be linearly polarized, (ii) E ≠ αB where α is a constant (iii) it is impossible to find a Lorentz frame where E>B, (iv) direction of the propagation vector cannot be inferred from the fields at one point of the space, (v) their behaviour under Lorentz, parity, time-reversal and gauge transformations is proper, (vi) both Lorentz invariants E2 - B2 and E·B are nonzero, (vii) the magnetic helicity may be nonzero, (viii) the magnetic field may be force-free, and (ix) kμFμv ≠ 0. It also shows how electromagnetic waves can be classified using Lorentz invariants. Cet article résume les qualités connues des ondes stationnaires E∥B TEM et montre que pour des ondes parallèles (i) E et B ne peuvent pas être polarisées linéairement, (ii) E ≠ αB où a est une constante, (iii) il est impossible de trouver une construction de Lorentz où E>B, (iv) la direction de propagation d'un vecteur ne peut pas être déduite des opérations à un point d'intervalle, (v) leur conduite sous Lorentz, parité, temps inverse et transformations de jauge est propre, (vi) les deux invariants de Lorentz E2 - B2 et E·B sont non nulles (vii) l'hélice magnétique peut être non nulle (viii) l'opération magnétique peut être de force libre et (ix) KμFμ v ≠ 0. Ceci montre aussi comment les ondes électromagnétiques peuvent être classifiées, en employant les invariants de Lorentz.

High-sensitivity green resist material with organic solvent-free spin-coating and tetramethylammonium hydroxide-free water-developable processes for EB and EUV lithography

Science.gov (United States)

Takei, Satoshi; Hanabata, Makoto; Oshima, Akihiro; Kashiwakura, Miki; Kozawa, Takahiro; Tagawa, Seiichi

2015-03-01

We investigated the eco-friendly electron beam (EB) and extreme-ultraviolet (EUV) lithography using a high-sensitive negative type of green resist material derived from biomass to take advantage of organic solvent-free water spin-coating and tetramethylammonium hydroxide(TMAH)-free water-developable techniques. A water developable, non-chemically amplified, high sensitive, and negative tone resist material in EB lithography was developed for environmental affair, safety, easiness of handling, and health of the working people, instead of the common developable process of TMAH. The material design concept to use the water-soluble resist material with acceptable properties such as pillar patterns with less than 100 nm in high EB sensitivity of 10 μC/cm2 and etch selectivity with a silicon-based middle layer in CF4 plasma treatment was demonstrated for EB and EUV lithography.

Kinetics of inclusion body formation and its correlation with the characteristics of protein aggregates in Escherichia coli.

Directory of Open Access Journals (Sweden)

Arun K Upadhyay

Full Text Available The objective of the research was to understand the structural determinants governing protein aggregation into inclusion bodies during expression of recombinant proteins in Escherichia coli. Recombinant human growth hormone (hGH and asparaginase were expressed as inclusion bodies in E.coli and the kinetics of aggregate formation was analyzed in details. Asparaginase inclusion bodies were of smaller size (200 nm and the size of the aggregates did not increase with induction time. In contrast, the seeding and growth behavior of hGH inclusion bodies were found to be sequential, kinetically stable and the aggregate size increased from 200 to 800 nm with induction time. Human growth hormone inclusion bodies showed higher resistance to denaturants and proteinase K degradation in comparison to those of asparaginase inclusion bodies. Asparaginase inclusion bodies were completely solubilized at 2-3 M urea concentration and could be refolded into active protein, whereas 7 M urea was required for complete solubilization of hGH inclusion bodies. Both hGH and asparaginase inclusion bodies showed binding with amyloid specific dyes. In spite of its low β-sheet content, binding with dyes was more prominent in case of hGH inclusion bodies than that of asparaginase. Arrangements of protein molecules present in the surface as well as in the core of inclusion bodies were similar. Hydrophobic interactions between partially folded amphiphillic and hydrophobic alpha-helices were found to be one of the main determinants of hGH inclusion body formation. Aggregation behavior of the protein molecules decides the nature and properties of inclusion bodies.

Kinetics of Inclusion Body Formation and Its Correlation with the Characteristics of Protein Aggregates in Escherichia coli

Science.gov (United States)

Upadhyay, Arun K.; Murmu, Aruna; Singh, Anupam; Panda, Amulya K.

2012-01-01

The objective of the research was to understand the structural determinants governing protein aggregation into inclusion bodies during expression of recombinant proteins in Escherichia coli. Recombinant human growth hormone (hGH) and asparaginase were expressed as inclusion bodies in E.coli and the kinetics of aggregate formation was analyzed in details. Asparaginase inclusion bodies were of smaller size (200 nm) and the size of the aggregates did not increase with induction time. In contrast, the seeding and growth behavior of hGH inclusion bodies were found to be sequential, kinetically stable and the aggregate size increased from 200 to 800 nm with induction time. Human growth hormone inclusion bodies showed higher resistance to denaturants and proteinase K degradation in comparison to those of asparaginase inclusion bodies. Asparaginase inclusion bodies were completely solubilized at 2–3 M urea concentration and could be refolded into active protein, whereas 7 M urea was required for complete solubilization of hGH inclusion bodies. Both hGH and asparaginase inclusion bodies showed binding with amyloid specific dyes. In spite of its low β-sheet content, binding with dyes was more prominent in case of hGH inclusion bodies than that of asparaginase. Arrangements of protein molecules present in the surface as well as in the core of inclusion bodies were similar. Hydrophobic interactions between partially folded amphiphillic and hydrophobic alpha-helices were found to be one of the main determinants of hGH inclusion body formation. Aggregation behavior of the protein molecules decides the nature and properties of inclusion bodies. PMID:22479486

Narvas näeb Eesti tantsuauhinna võitnud tantsulavastust / Rene Nõmmik ; intervjueerinud Tiia Linnart

Index Scriptorium Estoniae

Nõmmik, Rene, 1962-

2015-01-01

Narva kultuurimajas Rugodiv näeb Fine5 tantsuteatri lavastust "...and blue", mis võitis tänavu Eesti teatriauhinna. Etenduse koreograafideks ja lavastajateks on Tiina Ollesk ja Rene Nõmmik, keda on palutud lavastama ka Venemaale. Intervjuu Rene Nõmmikuga

Extracellular matrix aggregates from differentiating embryoid bodies as a scaffold to support ESC proliferation and differentiation.

Directory of Open Access Journals (Sweden)

Saik-Kia Goh

Full Text Available Embryonic stem cells (ESCs have emerged as potential cell sources for tissue engineering and regeneration owing to its virtually unlimited replicative capacity and the potential to differentiate into a variety of cell types. Current differentiation strategies primarily involve various growth factor/inducer/repressor concoctions with less emphasis on the substrate. Developing biomaterials to promote stem cell proliferation and differentiation could aid in the realization of this goal. Extracellular matrix (ECM components are important physiological regulators, and can provide cues to direct ESC expansion and differentiation. ECM undergoes constant remodeling with surrounding cells to accommodate specific developmental event. In this study, using ESC derived aggregates called embryoid bodies (EB as a model, we characterized the biological nature of ECM in EB after exposure to different treatments: spontaneously differentiated and retinoic acid treated (denoted as SPT and RA, respectively. Next, we extracted this treatment-specific ECM by detergent decellularization methods (Triton X-100, DOC and SDS are compared. The resulting EB ECM scaffolds were seeded with undifferentiated ESCs using a novel cell seeding strategy, and the behavior of ESCs was studied. Our results showed that the optimized protocol efficiently removes cells while retaining crucial ECM and biochemical components. Decellularized ECM from SPT EB gave rise to a more favorable microenvironment for promoting ESC attachment, proliferation, and early differentiation, compared to native EB and decellularized ECM from RA EB. These findings suggest that various treatment conditions allow the formulation of unique ESC-ECM derived scaffolds to enhance ESC bioactivities, including proliferation and differentiation for tissue regeneration applications.

Rice body formation in bicipito-radial bursitis: ultrasound, CT, and MRI findings

International Nuclear Information System (INIS)

Spence, L.D.; Adams, J.; Eustace, S.; Gibbons, D.; Mason, M.D.

1998-01-01

The bicipito-radial bursa, which lies at the biceps tendon insertion on the radial tuberosity, is a rare site of chronic bursitis. We describe the clinical, radiological, and pathological findings in a case complicated by multiple rice body formation. In so doing, we describe MR appearances that allow discrimination of this entity from both synovial chondromatosis and pigmented villonodular synovitis. (orig.)

Adopting a Sustainable Community of Practice Model when Developing a Service to Support Patients with Epidermolysis Bullosa (EB): A Stakeholder-Centered Approach.

Science.gov (United States)

Gowran, Rosemary Joan; Kennan, Avril; Marshall, Siobhán; Mulcahy, Irene; Ní Mhaille, Sile; Beasley, Sarah; Devlin, Mark

2015-02-01

Epidermolysis bullosa (EB) is a rare, genetic skin condition that is complicated, distressing, and painful and permeates every aspect of patients' lives. Support services are essential for meeting the primary needs of patients and families living with EB; however, provision is challenged by many complex issues. In collaboration with the patient organization DEBRA Ireland, this research conducted an in-depth analysis of Irish healthcare support services for EB, with a view to moving towards an improved and sustainable care pathway. A sustainable community of practice model (SCOP), as a core construct provided a simplified framework when studying this complex system. The research utilized mixed methods, comprising individual interviews, questionnaires, and a participatory action research workshop based on a soft systems approach. The study engaged patients, family members, service providers, and policy developers. Findings emphasized that the complexities of life with EB are more than 'skin deep'. The lived experience of stakeholders revealed many levels of emotion, both positive and heart-rending. Despite the positive efforts of specialists in this field, inadequacies to meet the primary needs of people with EB, such as bandages-fundamental for survival-were highlighted. Participants reported challenges relating to understanding patients' needs, access to consistent services within hospitals and the community, time constraints, and the strong emotions evoked by this severe and rare disease. The study identified several areas that can be targeted to bring about improvements in meeting primary needs. Education and research at public, policy, and practice levels need to be prioritized. It is imperative that citizens move beyond an awareness that EB exists and demonstrate a consciousness about the importance of advocating and enabling seamless and sustainable support services through collective action.

Multivesicular body formation enhancement and exosome release during endoplasmic reticulum stress.

Science.gov (United States)

Kanemoto, Soshi; Nitani, Ryota; Murakami, Tatsuhiko; Kaneko, Masayuki; Asada, Rie; Matsuhisa, Koji; Saito, Atsushi; Imaizumi, Kazunori

2016-11-11

The endoplasmic reticulum (ER) plays a pivotal role in maintaining cellular homeostasis. However, numerous environmental and genetic factors give rise to ER stress by inducing an accumulation of unfolded proteins. Under ER stress conditions, cells initiate the unfolded protein response (UPR). Here, we demonstrate a novel aspect of the UPR by electron microscopy and immunostaining analyses, whereby multivesicular body (MVB) formation was enhanced after ER stress. This MVB formation was influenced by inhibition of ER stress transducers inositol required enzyme 1 (IRE1) and PKR-like ER kinase (PERK). Furthermore, exosome release was also increased during ER stress. However, in IRE1 or PERK deficient cells, exosome release was not upregulated, indicating that IRE1- and PERK-mediated pathways are involved in ER stress-dependent exosome release. Copyright © 2016 Elsevier Inc. All rights reserved.

Recruitment of EB1, a Master Regulator of Microtubule Dynamics, to the Surface of the Theileria annulata Schizont

KAUST Repository

Woods, Kerry L.

2013-05-09

The apicomplexan parasite Theileria annulata transforms infected host cells, inducing uncontrolled proliferation and clonal expansion of the parasitized cell population. Shortly after sporozoite entry into the target cell, the surrounding host cell membrane is dissolved and an array of host cell microtubules (MTs) surrounds the parasite, which develops into the transforming schizont. The latter does not egress to invade and transform other cells. Instead, it remains tethered to host cell MTs and, during mitosis and cytokinesis, engages the cell\\'s astral and central spindle MTs to secure its distribution between the two daughter cells. The molecular mechanism by which the schizont recruits and stabilizes host cell MTs is not known. MT minus ends are mostly anchored in the MT organizing center, while the plus ends explore the cellular space, switching constantly between phases of growth and shrinkage (called dynamic instability). Assuming the plus ends of growing MTs provide the first point of contact with the parasite, we focused on the complex protein machinery associated with these structures. We now report how the schizont recruits end-binding protein 1 (EB1), a central component of the MT plus end protein interaction network and key regulator of host cell MT dynamics. Using a range of in vitro experiments, we demonstrate that T. annulata p104, a polymorphic antigen expressed on the schizont surface, functions as a genuine EB1-binding protein and can recruit EB1 in the absence of any other parasite proteins. Binding strictly depends on a consensus SxIP motif located in a highly disordered C-terminal region of p104. We further show that parasite interaction with host cell EB1 is cell cycle regulated. This is the first description of a pathogen-encoded protein to interact with EB1 via a bona-fide SxIP motif. Our findings provide important new insight into the mode of interaction between Theileria and the host cell cytoskeleton. 2013 Woods et al.

Recruitment of EB1, a master regulator of microtubule dynamics, to the surface of the Theileria annulata schizont.

Directory of Open Access Journals (Sweden)

Kerry L Woods

2013-05-01

Full Text Available The apicomplexan parasite Theileria annulata transforms infected host cells, inducing uncontrolled proliferation and clonal expansion of the parasitized cell population. Shortly after sporozoite entry into the target cell, the surrounding host cell membrane is dissolved and an array of host cell microtubules (MTs surrounds the parasite, which develops into the transforming schizont. The latter does not egress to invade and transform other cells. Instead, it remains tethered to host cell MTs and, during mitosis and cytokinesis, engages the cell's astral and central spindle MTs to secure its distribution between the two daughter cells. The molecular mechanism by which the schizont recruits and stabilizes host cell MTs is not known. MT minus ends are mostly anchored in the MT organizing center, while the plus ends explore the cellular space, switching constantly between phases of growth and shrinkage (called dynamic instability. Assuming the plus ends of growing MTs provide the first point of contact with the parasite, we focused on the complex protein machinery associated with these structures. We now report how the schizont recruits end-binding protein 1 (EB1, a central component of the MT plus end protein interaction network and key regulator of host cell MT dynamics. Using a range of in vitro experiments, we demonstrate that T. annulata p104, a polymorphic antigen expressed on the schizont surface, functions as a genuine EB1-binding protein and can recruit EB1 in the absence of any other parasite proteins. Binding strictly depends on a consensus SxIP motif located in a highly disordered C-terminal region of p104. We further show that parasite interaction with host cell EB1 is cell cycle regulated. This is the first description of a pathogen-encoded protein to interact with EB1 via a bona-fide SxIP motif. Our findings provide important new insight into the mode of interaction between Theileria and the host cell cytoskeleton.

Collection and application of by-product formed in e-b flue gas treatment process

International Nuclear Information System (INIS)

Chmielewski, A.G.; Tyminski, B.; Zakrzewska-Trznadel, G.; Tokunaga, O.; Machi, S.

1998-01-01

In the e-b process SO 2 and NO x are converted into ammonium sulphate and ammonium nitrate, which condenses from gas phase in the form of submicrone particles. These salts are a valuable fertilizer and should be removed from cleaned gas. Bag filter, ESP and wet gravel bed filter were applied for collecting of salt particles in pilot plant facilities. Up to now ESP is considered to be the best filtration method of aerosols formed after irradiation of flue gas. Collected salts after granulation may be used as a fertilizer enriching soil in nitrogen and sulphur or as a component of mixed fertilizer. Analysis of by-products from different e-b pilot plants confirms that it does not contain any harmful substances like heavy metals and fulfill all standards for commercial fertilizers. Also field experiments show that the by-products have the same properties as a commercial fertilizer

Rice body formation in bicipito-radial bursitis: ultrasound, CT, and MRI findings

Energy Technology Data Exchange (ETDEWEB)

Spence, L.D.; Adams, J.; Eustace, S. [Department of Radiology, Boston Medical Center, One Boston Medical Center Place, Boston MA 02118 (United States); Gibbons, D. [Department of Pathology, Boston Medical Center, Boston, Massachusetts (United States); Mason, M.D. [Department of Orthopedics, Boston Medical Center, Boston, Massachusetts (United States)

1998-01-01

The bicipito-radial bursa, which lies at the biceps tendon insertion on the radial tuberosity, is a rare site of chronic bursitis. We describe the clinical, radiological, and pathological findings in a case complicated by multiple rice body formation. In so doing, we describe MR appearances that allow discrimination of this entity from both synovial chondromatosis and pigmented villonodular synovitis. (orig.) With 3 figs., 8 refs.

EBS modelling for the development of repository concepts tailored to siting environments

International Nuclear Information System (INIS)

Ishiguro, K.; Ueda, H.; Wakasugi, K.; Sakabe, Y.; Kitayama, K.; Umeki, H.; Takase, H.

2007-01-01

The Japanese siting approach for a HLW repository calls for volunteer host municipalities and thereby places particular emphasis on design flexibility. In particular, the repository concept needs to be tailored to the specific site characteristics. Starting from the H12 repository concept, NUMO has been examining a range of possible repository design options, including the EBS. In this paper. the requirements and strategy for the development of models for performance assessment and process understanding are discussed, taking into account the step-wise, iterative process of developing repository concepts. The areas requiring further development of models and databases in the long-term R and D programme have been identified as a 'wish list' that relates to the evaluation of a range of potential repository concepts, focusing on the near-field for the early stages of the development process. Among the issues on the list, NUMO has started the development of a flexible computer code for modelling three-dimensional mass transport to evaluate the impacts of various design options and components of the EBS. This tool has been applied to the analysis of the barrier effects of the tunnel plugs located in fractured rock. (authors)

Understanding Combustion and Soot Formation in Diesel Engines

Science.gov (United States)

2016-09-09

distributions of PLII signals help understand the soot distributions within diesel/ biodiesel flames. In addition, planar laser-induced Figure 1. Transported ...Prescribed by ANSI Std. Z39.18 Page 1 of 1FORM SF 298 9/14/2016https://livelink.ebs.afrl.af.mil/livelink/llisapi.dll This project investigated biodiesel ...emissions testing. 1 FINAL REPORT Project title: Understanding combustion and soot formation in biodiesel fuelled diesel engines Lead Institute and

Induction of protein body formation in plant leaves by elastin-like polypeptide fusions

Directory of Open Access Journals (Sweden)

Joensuu Jussi J

2009-08-01

Full Text Available Abstract Background Elastin-like polypeptides are synthetic biopolymers composed of a repeating pentapeptide 'VPGXG' sequence that are valuable for the simple non-chromatographic purification of recombinant proteins. In addition, elastin-like polypeptide fusions have been shown to enhance the accumulation of a range of different recombinant proteins in plants, thus addressing the major limitation of plant-based expression systems, which is a low production yield. This study's main objectives were to determine the general utility of elastin-like polypeptide protein fusions in various intracellular compartments and to elucidate elastin-like polypeptide's mechanism of action for increasing recombinant protein accumulation in the endoplasmic reticulum of plants. Results The effect of elastin-like polypeptide fusions on the accumulation of green fluorescent protein targeted to the cytoplasm, chloroplasts, apoplast, and endoplasmic reticulum was evaluated. The endoplasmic reticulum was the only intracellular compartment in which an elastin-like polypeptide tag was shown to significantly enhance recombinant protein accumulation. Interestingly, endoplasmic reticulum-targeted elastin-like polypeptide fusions induced the formation of a novel type of protein body, which may be responsible for elastin-like polypeptide's positive effect on recombinant protein accumulation by excluding the heterologous protein from normal physiological turnover. Although expressed in the leaves of plants, these novel protein bodies appeared similar in size and morphology to the prolamin-based protein bodies naturally found in plant seeds. The elastin-like polypeptide-induced protein bodies were highly mobile organelles, exhibiting various dynamic patterns of movement throughout the cells, which were dependent on intact actin microfilaments and a functional actomyosin motility system. Conclusion An endoplasmic reticulum-targeted elastin-like polypeptide fusion approach

Cajal bodies and snRNPs friends with benefits

Czech Academy of Sciences Publication Activity Database

Staněk, David

2017-01-01

Roč. 14, č. 6 (2017), s. 671-679 ISSN 1547-6286 R&D Projects: GA ČR GA15-00790S Institutional support: RVO:68378050 Keywords : spinal muscular-atrophy * small nuclear-rna * u4/u6.u5 tri-snrnp * xenopus-laevis oocytes * u6 spliceosomal rna * coiled bodies * smn complex * u1 snrnp * u2 snrnp * in-vivo Subject RIV: EB - Genetics ; Molecular Biology OBOR OECD: Cell biology Impact factor: 3.900, year: 2016

Structure and characteristics of EB-PVD thermal insulation layers; Struktur und Eigenschaften von EB-PVD-Waermedaemmschichten

Energy Technology Data Exchange (ETDEWEB)

Schulz, U. [Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Koeln (Germany). Inst. fuer Werkstoff-Forschung

1996-12-31

Thermal insulation layers for guide blades and rotor blades in the first two stages of a high-pressure turbines are produced by electron-beam physical vapour deposition for maximum quality. The layers have a lifetime that is longer by a factor of 2 to 10 than for plasma-sprayed layers. The following characteristics of the ceramic layer have a decisive influence on the life of the composite system: Phase composition, distribution and stability, microstructure, density, thickness, crack distribution and cohesive strength. Some selected aspects of the interdependence between production parameters, microstructure of the thermal insulation layer and service life are gone into. [Deutsch] Zur Herstellung von Waermedaemmschichten (WDS) fuer Turbinenleit- und Laufschaufeln der ersten beiden Stufen in der Hochdruckturbine wird fuer hoechste Ansprueche an die Schichtqualitaet das EB-PDV-Verfahren (electron-beam physical vapour deposition) eingesetzt. Die Lebensdauer dieser Schichten ist um den Faktor 2 bis 10 besser als beim Plasmaspritzen. Bei der keramischen Waermedaemmschicht selbst beeinflussen folgende Eigenschaften die Lebensdauer des Gesamtschichtsystems nachhaltig: Phasenzusammensetzung, -verteilung und -stabilitaet, Mikrogefuege, Dichte, Dicke, Rissverteilung und kohaesive Festigkeit. Auf einige ausgewaehlt Aspekte des Zusammenhangs zwischen Herstellungsparametern, Mikrostruktur der Waermedaemmschicht und Lebensdauer wird kurz eingegangen. (orig.)

Establishment of Human Neural Progenitor Cells from Human Induced Pluripotent Stem Cells with Diverse Tissue Origins

Directory of Open Access Journals (Sweden)

Hayato Fukusumi

2016-01-01

Full Text Available Human neural progenitor cells (hNPCs have previously been generated from limited numbers of human induced pluripotent stem cell (hiPSC clones. Here, 21 hiPSC clones derived from human dermal fibroblasts, cord blood cells, and peripheral blood mononuclear cells were differentiated using two neural induction methods, an embryoid body (EB formation-based method and an EB formation method using dual SMAD inhibitors (dSMADi. Our results showed that expandable hNPCs could be generated from hiPSC clones with diverse somatic tissue origins. The established hNPCs exhibited a mid/hindbrain-type neural identity and uniform expression of neural progenitor genes.

Ice bridges and ridges in the Maxwell-EB sea ice rheology

Directory of Open Access Journals (Sweden)

V. Dansereau

2017-09-01

Full Text Available This paper presents a first implementation of a new rheological model for sea ice on geophysical scales. This continuum model, called Maxwell elasto-brittle (Maxwell-EB, is based on a Maxwell constitutive law, a progressive damage mechanism that is coupled to both the elastic modulus and apparent viscosity of the ice cover and a Mohr–Coulomb damage criterion that allows for pure (uniaxial and biaxial tensile strength. The model is tested on the basis of its capability to reproduce the complex mechanical and dynamical behaviour of sea ice drifting through a narrow passage. Idealized as well as realistic simulations of the flow of ice through Nares Strait are presented. These demonstrate that the model reproduces the formation of stable ice bridges as well as the stoppage of the flow, a phenomenon occurring within numerous channels of the Arctic. In agreement with observations, the model captures the propagation of damage along narrow arch-like kinematic features, the discontinuities in the velocity field across these features dividing the ice cover into floes, the strong spatial localization of the thickest, ridged ice, the presence of landfast ice in bays and fjords and the opening of polynyas downstream of the strait. The model represents various dynamical behaviours linked to an overall weakening of the ice cover and to the shorter lifespan of ice bridges, with implications in terms of increased ice export through narrow outflow pathways of the Arctic.

Ice bridges and ridges in the Maxwell-EB sea ice rheology

Science.gov (United States)

Dansereau, Véronique; Weiss, Jérôme; Saramito, Pierre; Lattes, Philippe; Coche, Edmond

2017-09-01

This paper presents a first implementation of a new rheological model for sea ice on geophysical scales. This continuum model, called Maxwell elasto-brittle (Maxwell-EB), is based on a Maxwell constitutive law, a progressive damage mechanism that is coupled to both the elastic modulus and apparent viscosity of the ice cover and a Mohr-Coulomb damage criterion that allows for pure (uniaxial and biaxial) tensile strength. The model is tested on the basis of its capability to reproduce the complex mechanical and dynamical behaviour of sea ice drifting through a narrow passage. Idealized as well as realistic simulations of the flow of ice through Nares Strait are presented. These demonstrate that the model reproduces the formation of stable ice bridges as well as the stoppage of the flow, a phenomenon occurring within numerous channels of the Arctic. In agreement with observations, the model captures the propagation of damage along narrow arch-like kinematic features, the discontinuities in the velocity field across these features dividing the ice cover into floes, the strong spatial localization of the thickest, ridged ice, the presence of landfast ice in bays and fjords and the opening of polynyas downstream of the strait. The model represents various dynamical behaviours linked to an overall weakening of the ice cover and to the shorter lifespan of ice bridges, with implications in terms of increased ice export through narrow outflow pathways of the Arctic.

N-body simulations of planet formation: understanding exoplanet system architectures

Science.gov (United States)

Coleman, Gavin; Nelson, Richard

2015-12-01

Observations have demonstrated the existence of a significant population of compact systems comprised of super-Earths and Neptune-mass planets, and a population of gas giants that appear to occur primarily in either short-period (100 days) orbits. The broad diversity of system architectures raises the question of whether or not the same formation processes operating in standard disc models can explain these planets, or if different scenarios are required instead to explain the widely differing architectures. To explore this issue, we present the results from a comprehensive suite of N-body simulations of planetary system formation that include the following physical processes: gravitational interactions and collisions between planetary embryos and planetesimals; type I and II migration; gas accretion onto planetary cores; self-consistent viscous disc evolution and disc removal through photo-evaporation. Our results indicate that the formation and survival of compact systems of super-Earths and Neptune-mass planets occur commonly in disc models where a simple prescription for the disc viscosity is assumed, but such models never lead to the formation and survival of gas giant planets due to migration into the star. Inspired in part by the ALMA observations of HL Tau, and by MHD simulations that display the formation of long-lived zonal flows, we have explored the consequences of assuming that the disc viscosity varies in both time and space. We find that the radial structuring of the disc leads to conditions in which systems of giant planets are able to form and survive. Furthermore, these giants generally occupy those regions of the mass-period diagram that are densely populated by the observed gas giants, suggesting that the planet traps generated by radial structuring of protoplanetary discs may be a necessary ingredient for forming giant planets.

EB treatment of wastewater and progress of on-going project in China

International Nuclear Information System (INIS)

Wang Zhiguang

2006-01-01

Electron beam processing has been widely used in China in the fields of radiation crosslinking cables and wires, heat shrinkable material, foam materials, irradiated latex and polymers, sterilization, removal SOx and NOx of flue gas, chemical industry, industrial CT, electron instrument, and so on. However, EB treatment of wastewater is mostly under study in laboratory. The manufacture of electron accelerators has also become a comparatively independent industry in China. (author)

P-body loss is concomitant with formation of a messenger RNA storage domain in mouse oocytes

Czech Academy of Sciences Publication Activity Database

Flemr, Matyáš; Ma, J.; Schultz, R. M.; Svoboda, Petr

2010-01-01

Roč. 82, č. 5 (2010), s. 1008-1017 ISSN 0006-3363 R&D Project s: GA MŠk ME09039 Grant - others:EMBO SDIG(DE) project 1483 Institutional research plan: CEZ:AV0Z50520514 Keywords : oocyte * mRNA * cortex Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 3.870, year: 2010

Studies of Planet Formation using a Hybrid N-body + Planetesimal Code

Science.gov (United States)

Kenyon, Scott J.; Bromley, Benjamin C.; Salamon, Michael (Technical Monitor)

2005-01-01

The goal of our proposal was to use a hybrid multi-annulus planetesimal/n-body code to examine the planetesimal theory, one of the two main theories of planet formation. We developed this code to follow the evolution of numerous 1 m to 1 km planetesimals as they collide, merge, and grow into full-fledged planets. Our goal was to apply the code to several well-posed, topical problems in planet formation and to derive observational consequences of the models. We planned to construct detailed models to address two fundamental issues: 1) icy planets - models for icy planet formation will demonstrate how the physical properties of debris disks, including the Kuiper Belt in our solar system, depend on initial conditions and input physics; and 2) terrestrial planets - calculations following the evolution of 1-10 km planetesimals into Earth-mass planets and rings of dust will provide a better understanding of how terrestrial planets form and interact with their environment. During the past year, we made progress on each issue. Papers published in 2004 are summarized. Summaries of work to be completed during the first half of 2005 and work planned for the second half of 2005 are included.

Late effects of atomic bomb radiation on human immune responses, (10); Results on studies of immune responses to EB-virus

Energy Technology Data Exchange (ETDEWEB)

Kusunoki, Yoichiro; Kyoizumi, Seishi; Ozaki, Kyoko; Saito, Mayumi; Cologne, J.B.; Akiyama, Mitoshi (Radiation Effects Research Foundation, Hiroshima (Japan))

1992-12-01

Anti-Epstein-Barr (EV) virus antibody titers were measured in age- and sex-matched three groups of each 124 A-bomb survivors who had exposed to <0.01 Gy, 0.01-1 Gy, or >1 Gy. These serum samples showed positive antibodies against viral capsid antigens (VCA). Antibody titers to anti-VCA-IgM or anti-EA-IgG were significantly higher in the groups of 0.01-1 Gy and >1 Gy than in the group of <0.01 Gy, reflecting decreased immune response ability for EV virus. When precursor frequency of cytotoxic cells against autologous EB virus LCL was determined in 68 other A-bomb survivors, no definitive influence of A-bombing was observed. However, serological study revealed that there was inverse correlation between precursor frequency and anti-EA-IgG antibody titer. These findings suggest that the immune response ability for EB virus may have been damaged and that biological reactivity of EB virus may occur frequently in A-bomb survivors. (N.K.).

Genetic polymorphisms in DNA repair and oxidative stress pathways may modify the association between body size and postmenopausal breast cancer

Czech Academy of Sciences Publication Activity Database

McCullough, L. E.; Eng, S. M.; Bradshaw, P. T.; Cleveland, R. J.; Steck, S. E.; Terry, M. B.; Shen, J.; Crew, K.D.; Rössner ml., Pavel; Ahn, J.; Ambrosone, Ch.B.; Teitelbaum, S. L.; Neugut, A. I.; Santella, R. M.; Gammon, M. D.

2015-01-01

Roč. 25, č. 4 (2015), s. 263-269 ISSN 1047-2797 Institutional support: RVO:68378041 Keywords : breast cancer * body mass index * oxidative stress * DNA repair * Epidemiology Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 2.335, year: 2015

Target Registration Error minimization involving deformable organs using elastic body splines and Particle Swarm Optimization approach.

Science.gov (United States)

Spinczyk, Dominik; Fabian, Sylwester

2017-12-01

In minimally invasive surgery one of the main challenges is the precise location of the target during the intervention. The aim of the study is to present usability of elastic body splines (EBS) to minimize TRE error. The method to find the desired EBS parameters values is presented with usage of Particle Swarm optimization approach. This ability of TRE minimization has been achieved for the respiratory phases corresponding to minimum FRE for abdominal (especially liver) surgery. The proposed methodology was verified during experiments conducted on 21 patients diagnosed with liver tumors. This method has been developed to perform operations in real-time on a standard workstation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Functionalization with C-terminal cysteine enhances transfection efficiency of cell-penetrating peptides through dimer formation

Energy Technology Data Exchange (ETDEWEB)

Amand, Helene L., E-mail: helene.amand@chalmers.se [Chalmers University of Technology, Department of Chemical and Biological Engineering/Physical Chemistry, SE-412 96 Gothenburg (Sweden); Norden, Bengt, E-mail: norden@chalmers.se [Chalmers University of Technology, Department of Chemical and Biological Engineering/Physical Chemistry, SE-412 96 Gothenburg (Sweden); Fant, Kristina, E-mail: kristina.fant@sp.se [Chalmers University of Technology, Department of Chemical and Biological Engineering/Physical Chemistry, SE-412 96 Gothenburg (Sweden)

2012-02-17

Highlights: Black-Right-Pointing-Pointer Reversible CPP dimerisation is a simple yet efficient strategy to improve delivery. Black-Right-Pointing-Pointer Dimer formation enhances peptiplex stability, resulting in increased transfection. Black-Right-Pointing-Pointer By dimerisation, the CPP EB1 even gain endosomal escape properties while lowering cytotoxicity. -- Abstract: Cell-penetrating peptides have the ability to stimulate uptake of macromolecular cargo in mammalian cells in a non-toxic manner and therefore hold promise as efficient and well tolerated gene delivery vectors. Non-covalent peptide-DNA complexes ('peptiplexes') enter cells via endocytosis, but poor peptiplex stability and endosomal entrapment are considered as main barriers to peptide-mediated delivery. We explore a simple, yet highly efficient, strategy to improve the function of peptide-based vectors, by adding one terminal cysteine residue. This allows the peptide to dimerize by disulfide bond formation, increasing its affinity for nucleic acids by the 'chelate effect' and, when the bond is reduced intracellularly, letting the complex dissociate to deliver the nucleic acid. By introducing a single C-terminal cysteine in the classical CPP penetratin and the penetratin analogs PenArg and EB1, we show that this minor modification greatly enhances the transfection capacity for plasmid DNA in HEK293T cells. We conclude that this effect is mainly due to enhanced thermodynamic stability of the peptiplexes as endosome-disruptive chloroquine is still required for transfection and the effect is more pronounced for peptides with lower inherent DNA condensation capacity. Interestingly, for EB1, addition of one cysteine makes the peptide able to mediate transfection in absence of chloroquine, indicating that dimerisation can also improve endosomal escape properties. Further, the cytotoxicity of EB1 peptiplexes is considerably reduced, possibly due to lower concentration of free peptide

Alteration of non-metallic barriers and evolution of solution chemistry in salt formations in Germany

International Nuclear Information System (INIS)

Herbert, H.J.; Becker, D.; Hagemann, S.; Meyer, Th.; Noseck, U.; Rubel, A.; Mauke, R.; Wollrath, J.

2005-01-01

Different Engineered Barrier Systems (EBS) materials considered in Germany for the sealing of repositories in salt formations are presented. Their long term behaviour in terms of interactions with salt solutions is discussed and evaluated. The discussed EBS materials are crushed salt, self sealing salt backfill, bentonite and salt concrete. Whereas the knowledge concerning the geochemical, geomechanical, hydrological and thermal behavior of crushed salt and salt concrete is well advanced further research is needed for other EBS materials. The self healing salt backfill has also been investigated in depth recently. In order to fully qualify this material large scale in situ experiments are still needed. The present knowledge on compacted bentonites in a salt environment is not yet sufficient for reliable predictions of the long-term performance in salt formations. The sealing concept of the low- and intermediate-level Radioactive Waste Repository Morsleben (ERAM) in a former rock salt and potash mine is presented. This concept is based on cementitious materials, i.e. salt concrete. The geochemical stability of different salt concretes in contact with brines expected in ERAM is addressed. It is shown how the results from leaching experiments and geochemical modelling are used in the safety analyses and how the chemical boundary conditions prevailing in the EBS influence the development of the permeability of the sealing system and thus control the radionuclide release. As a result of modelling the behaviour of the seals in the safety assessment it is shown, that the seals are corroded within a time span of about 20 000 years. The influence of the uncertainty in the model parameters on the safety of the repository was assessed by a variation of the initial permeability of the seal. The maximum dose rate resulting from the radionuclide release from ERAM is nearly independent of the variation of the initial permeability within four orders of magnitude. (authors)

Functionalization with C-terminal cysteine enhances transfection efficiency of cell-penetrating peptides through dimer formation

International Nuclear Information System (INIS)

Åmand, Helene L.; Nordén, Bengt; Fant, Kristina

2012-01-01

Highlights: ► Reversible CPP dimerisation is a simple yet efficient strategy to improve delivery. ► Dimer formation enhances peptiplex stability, resulting in increased transfection. ► By dimerisation, the CPP EB1 even gain endosomal escape properties while lowering cytotoxicity. -- Abstract: Cell-penetrating peptides have the ability to stimulate uptake of macromolecular cargo in mammalian cells in a non-toxic manner and therefore hold promise as efficient and well tolerated gene delivery vectors. Non-covalent peptide-DNA complexes (“peptiplexes”) enter cells via endocytosis, but poor peptiplex stability and endosomal entrapment are considered as main barriers to peptide-mediated delivery. We explore a simple, yet highly efficient, strategy to improve the function of peptide-based vectors, by adding one terminal cysteine residue. This allows the peptide to dimerize by disulfide bond formation, increasing its affinity for nucleic acids by the “chelate effect” and, when the bond is reduced intracellularly, letting the complex dissociate to deliver the nucleic acid. By introducing a single C-terminal cysteine in the classical CPP penetratin and the penetratin analogs PenArg and EB1, we show that this minor modification greatly enhances the transfection capacity for plasmid DNA in HEK293T cells. We conclude that this effect is mainly due to enhanced thermodynamic stability of the peptiplexes as endosome-disruptive chloroquine is still required for transfection and the effect is more pronounced for peptides with lower inherent DNA condensation capacity. Interestingly, for EB1, addition of one cysteine makes the peptide able to mediate transfection in absence of chloroquine, indicating that dimerisation can also improve endosomal escape properties. Further, the cytotoxicity of EB1 peptiplexes is considerably reduced, possibly due to lower concentration of free peptide dimer resulting from its stronger binding to DNA.

Studies on muon cycling rates in muon catalyzed D-T fusion system with possible four-body muonic molecules formation

International Nuclear Information System (INIS)

Eskandri, M.R.; Hosini Motlagh, N.; Hataf, A.

2000-01-01

In recent studies, it is shown that the fusion rate for four-body molecules of ppμμ, ddμμ, ptμμ, pdμμ, dtμμ, ttμμ, is considerably larger than that of similar three-body molecules of ppμμ, ddμμ, ptμμ, pdμμ, dtμμ, ttμμ. It is shown that for dtμμ, fusion rate is R f (dt) ≅ 3 * 10 13 - 6 * * 10 13 S -1 which is 40 times higher than fusion rate of dtμμ molecule. In this paper we have looked for the effect of these molecules formation in muon catalyzed D-T fusion. The required data for all possible branches do not exist, so the main dtμμ branch are considered here. By choosing a variable value for dtμμ molecule formation rate and comparing obtained cycling rates with existing experimental values, the order of this parameter is evaluated to be ≅ 10 9 S -1 . Using obtained data in different conditions of D-T muon cycling rate calculations have shown that considering of four-body molecule formations in existing muon injection intensities do not make considerable change in three-body muonic molecule cycling rate

Silica enhanced formation of hydroxyapatite nanocrystals in simulated body fluid (SBF) at 37 deg. C

Energy Technology Data Exchange (ETDEWEB)

Sadjadi, M.S., E-mail: m.s.sadjad@gmail.com [Department of Chemistry, Sciences and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Ebrahimi, H.R. [Department of Chemistry, Sciences and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Meskinfam, M. [Department of Chemistry, Tonekabon Branch, Islamic Azad University, Tonekabon (Iran, Islamic Republic of); Zare, K. [Department of Chemistry, University of Shahid Beheshti, Eveen Tehran (Iran, Islamic Republic of)

2011-10-17

Highlights: {yields} We report on fast formation of hexagonal nanocrystals of calcium hydroxyapatite (HA) in silica-containing simulated body fluid solution at 37 deg. C. {yields} Bioactivity and biodegradability of TCP precursor have been confirmed by the dissolution of TCP and formation of a bone like layer of new HA nanoparticles outside of the precursor after 24 h soaking in SBF solution. {yields} Successive nucleation and formation of tiny hexagonal HA nanoplates and nanorods have been confirmed by TEM results after 24 h soaking of TCP in silica-containing BSF solution. - Abstract: The chemical modification of implant (prosthesis) surfaces is being investigated worldwide for improving the fixation of orthopaedic and dental implants. The main goal in this surface modification approach is to achieve a faster bone growth and chemical bonding of the implant to the newly generated and/or remodeled bone. In this work, we report fast formation of hexagonal nanocrystals of calcium hydroxyapatite (HA) in simulated body fluid (SBF, inorganic components of human blood plasma) solutions at 37 deg. C, using calcium phosphate (TCP) and sodium silicate as precursors. Characterization and chemical analysis of the synthesized powders were performed by Fourier transform infrared spectroscopy (FT-IR), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results indicated enhanced nucleation and formation of bone like layer of HA nanocrystals at the surface of TCP nanoparticles and occurrence of HA nanocrystals during 24 h soaking of TCP in SBF solution containing silica ions. The average size of a nanoparticle, using Scherrer formula, was found to be 18.2 nm.

Silica enhanced formation of hydroxyapatite nanocrystals in simulated body fluid (SBF) at 37 deg. C

International Nuclear Information System (INIS)

Sadjadi, M.S.; Ebrahimi, H.R.; Meskinfam, M.; Zare, K.

2011-01-01

Highlights: → We report on fast formation of hexagonal nanocrystals of calcium hydroxyapatite (HA) in silica-containing simulated body fluid solution at 37 deg. C. → Bioactivity and biodegradability of TCP precursor have been confirmed by the dissolution of TCP and formation of a bone like layer of new HA nanoparticles outside of the precursor after 24 h soaking in SBF solution. → Successive nucleation and formation of tiny hexagonal HA nanoplates and nanorods have been confirmed by TEM results after 24 h soaking of TCP in silica-containing BSF solution. - Abstract: The chemical modification of implant (prosthesis) surfaces is being investigated worldwide for improving the fixation of orthopaedic and dental implants. The main goal in this surface modification approach is to achieve a faster bone growth and chemical bonding of the implant to the newly generated and/or remodeled bone. In this work, we report fast formation of hexagonal nanocrystals of calcium hydroxyapatite (HA) in simulated body fluid (SBF, inorganic components of human blood plasma) solutions at 37 deg. C, using calcium phosphate (TCP) and sodium silicate as precursors. Characterization and chemical analysis of the synthesized powders were performed by Fourier transform infrared spectroscopy (FT-IR), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results indicated enhanced nucleation and formation of bone like layer of HA nanocrystals at the surface of TCP nanoparticles and occurrence of HA nanocrystals during 24 h soaking of TCP in SBF solution containing silica ions. The average size of a nanoparticle, using Scherrer formula, was found to be 18.2 nm.

The Contribution of the Human Body in Young Children's Explanations About Shadow Formation

Science.gov (United States)

Herakleioti, Evagelia; Pantidos, Panagiotis

2016-02-01

This paper begins with the view that the generation of meaning is a multimodal process. Props, drawings, graphs, gestures, as well as speech and written text are all mediators through which students construct new knowledge. Each semiotic context makes a unique contribution to the conceptualization of scientific entities. The human body, in particular, can function as a factor in both representation and explanation, serving as a link between verbal discourse and setting. Considering this perspective, a body-based activity was designed for kindergarten children, involving the concept of a shadow. The 3-D arrangement of the light from the light source, the human body (the obstacle), and the resulting shadow plays a central role. Using their own bodies as obstacles to the light, the children were able to explore the direction of the light and to change the relative positions of the light source and the obstacle. They formed hypotheses and were able to test them by moving on the stage. This body-centered activity explicitly incorporates the rectilinear movement of light into the process of shadow formation, while also providing learning through direct experience. Positive effects on learning were achieved for the group of children who participated in the activity, while the video analysis showed that many of the children were able to use their bodies to transfer to a different setting the embodied knowledge they acquired. This, according to researchers in the field of science education, is a powerful indication of conceptual change.

Welding of cold worked austenitic steels - comparison of TIG, EB and laser processes

International Nuclear Information System (INIS)

Richard, A.; Prunele, D. de; Castilan, F.

1993-01-01

Effect of welding on cold worked components is a local falling of their properties. Modifications induced by such an operation depend on the thermal cycle and consequently on the welding process. An experimental study aim of which is to compare respective effects of different welding processes (TIG, EB, laser) has been realized. This publication presents results related to 316L and 316Ti steels. (author). 2 refs., 7 figs., 1 tab

Cream and albinotic – two new mutations affecting body colour in Pyrrhocoris apterus (Heteroptera: Pyrrhocoridae)

Czech Academy of Sciences Publication Activity Database

Socha, Radomír

2011-01-01

Roč. 108, č. 1 (2011), s. 17-24 ISSN 1210-5759 R&D Projects: GA ČR GAP501/10/1215 Institutional research plan: CEZ:AV0Z50070508 Keywords : firebug * body- colour mutants * albinotic Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 1.061, year: 2011 http://www.eje.cz/scripts/viewabstract.php?abstract=1582

Cow body condition affects the hormonal release of ovarian cells and their responses to gonadotropic and metabolic hormones

Czech Academy of Sciences Publication Activity Database

Sirotkin, A. V.; Makarevich, A. V.; Laurinčík, Jozef; Alawasel, S.; Harrath, A. H.

2018-01-01

Roč. 110, č. 3 (2018), s. 142-147 ISSN 0093-691X R&D Projects: GA MŠk EF15_003/0000460 Institutional support: RVO:67985904 Keywords : ovary * body condition * progesterone Subject RIV: EB - Genetics ; Molecular Biology OBOR OECD: Developmental biology Impact factor: 1.986, year: 2016

Hydroxyapatite formation on titania-based materials in a solution mimicking body fluid: Effects of manganese and iron addition in anatase.

Science.gov (United States)

Shin, Euisup; Kim, Ill Yong; Cho, Sung Baek; Ohtsuki, Chikara

2015-03-01

Hydroxyapatite formation on the surfaces of implanted materials plays an important role in osteoconduction of bone substitutes in bone tissues. Titania hydrogels are known to instigate hydroxyapatite formation in a solution mimicking human blood plasma. To date, the relationship between the surface characteristics of titania and hydroxyapatite formation on its surface remains unclear. In this study, titania powders with varying surface characteristics were prepared by addition of manganese or iron to examine hydroxyapatite formation in a type of simulated body fluid (Kokubo solution). Hydroxyapatite formation was monitored by observation of deposited particles with scale-like morphology on the prepared titania powders. The effect of the titania surface characteristics, i.e., crystal structure, zeta potential, hydroxy group content, and specific surface area, on hydroxyapatite formation was examined. Hydroxyapatite formation was observed on the surface of titania powders that were primarily anatase, and featured a negative zeta potential and low specific surface areas irrespective of the hydroxy group content. High specific surface areas inhibited the formation of hydroxyapatite because calcium and phosphate ions were mostly consumed by adsorption on the titania surface. Thus, these surface characteristics of titania determine its osteoconductivity following exposure to body fluid. Copyright © 2014 Elsevier B.V. All rights reserved.

pKWmEB: integration of Kruskal-Wallis test with empirical Bayes under polygenic background control for multi-locus genome-wide association study.

Science.gov (United States)

Ren, Wen-Long; Wen, Yang-Jun; Dunwell, Jim M; Zhang, Yuan-Ming

2018-03-01

Although nonparametric methods in genome-wide association studies (GWAS) are robust in quantitative trait nucleotide (QTN) detection, the absence of polygenic background control in single-marker association in genome-wide scans results in a high false positive rate. To overcome this issue, we proposed an integrated nonparametric method for multi-locus GWAS. First, a new model transformation was used to whiten the covariance matrix of polygenic matrix K and environmental noise. Using the transferred model, Kruskal-Wallis test along with least angle regression was then used to select all the markers that were potentially associated with the trait. Finally, all the selected markers were placed into multi-locus model, these effects were estimated by empirical Bayes, and all the nonzero effects were further identified by a likelihood ratio test for true QTN detection. This method, named pKWmEB, was validated by a series of Monte Carlo simulation studies. As a result, pKWmEB effectively controlled false positive rate, although a less stringent significance criterion was adopted. More importantly, pKWmEB retained the high power of Kruskal-Wallis test, and provided QTN effect estimates. To further validate pKWmEB, we re-analyzed four flowering time related traits in Arabidopsis thaliana, and detected some previously reported genes that were not identified by the other methods.

Generation of Cardiomyocytes in Pipe-Based Microbioreactor Under Segmented Flow

Directory of Open Access Journals (Sweden)

Dimitry Spitkovsky

2016-05-01

Full Text Available Background/Aims: Embryonic stem (ES cells have got a broad range differentiation potential. The differentiation is initiated via aggregation of non-differentiated ES cells into embryoid body (EB capable of multi-lineage development. However experimental variables present in standard differentiation techniques lead to high EB heterogeneity, affecting development into the cells of desired lineage, and do not support the process automatization and scalability. Methods: Here we present a novel pipe based microbioreactor (PBM setup based on segmented flow, designed for spatial maintenance of temperature, nutrition supply, gas supply and sterility. Results: We verified PBM feasibility for continuous process generating cardiac cells starting from single ES cell suspension followed by EB formation for up to 10 days. The ES cells used in the study were genetically modified for cardiac-specific EGFP expression allowing optical monitoring of cardiomyocytes while EBs remained within PBM for up to 10 days. Efficiency of cardiac cells formation within PBM was similar compared to a standard hanging drop based protocol. Conclusion: Our findings ensure further development of microfluidic bioreactor technology to enable robust cardiomyocytes production for needs of drug screening, tissue engineering and other applications.

A hollow sphere soft lithography approach for long-term hanging drop methods.

Science.gov (United States)

Lee, Won Gu; Ortmann, Daniel; Hancock, Matthew J; Bae, Hojae; Khademhosseini, Ali

2010-04-01

In conventional hanging drop (HD) methods, embryonic stem cell aggregates or embryoid bodies (EBs) are often maintained in small inverted droplets. Gravity limits the volumes of these droplets to less than 50 microL, and hence such cell cultures can only be sustained for a few days without frequent media changes. Here we present a new approach to performing long-term HD methods (10-15 days) that can provide larger media reservoirs in a HD format to maintain more consistent culture media conditions. To implement this approach, we fabricated hollow sphere (HS) structures by injecting liquid drops into noncured poly(dimethylsiloxane) mixtures. These structures served as cell culture chambers with large media volumes (500 microL in each sphere) where EBs could grow without media depletion. The results showed that the sizes of the EBs cultured in the HS structures in a long-term HD format were approximately twice those of conventional HD methods after 10 days in culture. Further, HS cultures showed multilineage differentiation, similar to EBs cultured in the HD method. Due to its ease of fabrication and enhanced features, this approach may be of potential benefit as a stem cell culture method for regenerative medicine.

Synchronization of vortex formation frequency with the body motion frequency at high Reynolds numbers

Energy Technology Data Exchange (ETDEWEB)

Pereira, Luiz Antonio Alcantara [Federal University of Itajuba (UNIFEI), MG (Brazil). Inst. of Mechanical Engineering], E-mail: luizantp@unifei.edu.br; Hirata, Miguel Hiroo [State University of Rio de Janeiro (FAT/UERJ), Resende, RJ (Brazil). Fac. de Tecnologia], E-mail: hirata@fat.uerj.br

2010-07-01

Understanding vortex induced vibrations is of great importance in the design of a variety of offshore engineering structures, nuclear plant components and cylindrical elements in tube-bank heat exchangers, for example. If a body is placed in a flow, it experiences alternating lift and drag forces caused by the asymmetric formation of vortices, which can cause a structure to vibrate. One of the most interesting features of this flow is the phenomenon of lock-in which is observed when the vortex shedding frequency is close to the body oscillation frequency. This paper presents the results of numerical experiments on vortex shedding from a circular cylinder vibrating in-line or transversely with an incident uniform flow at Reynolds number of 1.0 x 10{sup 5}. The frequencies of the lift and drag coefficients are compared with the body motion frequency when the frequency ratio is about unity. (author)

Dismantling of the EB experiment: Experimental research on the retrieved GBM and bentonite blocks

Energy Technology Data Exchange (ETDEWEB)

Liu, Jiang-Feng, E-mail: jeafliu@hotmail.com [State Key Laboratory for Geomchanics & Deep Underground Engineering, and School of Mechanics and Civil Engineering, China University of Mining & Technology, Xuzhou, Jiangsu 221116 (China); Laboratoire de Méchanique de Lille (LML), and École Centrale de Lille, BP 48, F-59651 Villeneuve d’Ascq Cedex (France); Skoczylas, Frédéric [Laboratoire de Méchanique de Lille (LML), and École Centrale de Lille, BP 48, F-59651 Villeneuve d’Ascq Cedex (France); Talandier, Jean [ANDRA, 1-7 rue Jean Monnet, 92298 Châtenay-Malabry Cedex (France); Pu, Hai [State Key Laboratory for Geomchanics & Deep Underground Engineering, and School of Mechanics and Civil Engineering, China University of Mining & Technology, Xuzhou, Jiangsu 221116 (China)

2016-04-15

Graphical abstract: - Highlights: • We present a demonstration of a new concept of HLW (high-level waste) repositories. • The hydro-mechanical characteristics of GBM and blocks were determined. • The water retention curves (WRCs) of GBM and blocks were presented. • The effective gas permeability of the GBM and blocks were measured. • The homogeneity of the GBM and blocks were investigated. - Abstract: The Engineered Barrier Emplacement Experiment in Opalinus Clay (EB experiment) was a full-scale test for the demonstration of a new concept of high-level waste (HLW) repositories in horizontal drifts in the Opalinus Clay formation. After 10.5 years of hydration, the EB experiment was dismantled in autumn 2012. Samples obtained from the granular bentonite material (GBM), and bentonite blocks were sent to a laboratory for further analysis. The bentonite samples analyzed at the Laboratory of Mechanic of Lille (LML) were obtained from the CMT1, CMT2, CMT3 and RW sections. Their physical states were determined, as were their effective gas permeability and swelling capacity at different relative humidity (RH) levels. The results indicate that the water contents of the GBM determined in the laboratory ranged between 25.63% and 44.88% and that the dry densities ranged between 1.13 and 1.44 g/cm{sup 3}. The blocks had water contents similar to (or slightly higher than) those of the GBM, and their dry densities had decreased from an initial value of 1.69 g/cm{sup 3} to values close to 1.30 g/cm{sup 3}, which were similar to the average values found in the GBM. The effective gas permeabilities of the GBM samples were within the range of 1.50 × 10{sup −22} m{sup 2} and 1.03 × 10{sup −17} m{sup 2}, whereas, the corresponding values of the samples obtained from the blocks were between 2.20 × 10{sup −21} m{sup 2} and 5.12 × 10{sup −21} m{sup 2}. The permeability values are primarily related to the dry densities and water contents of the samples. Contact with

76 FR 59927 - Treatment of Aliens Whose Employment Creation Immigrant (EB-5) Petitions Were Approved After...

Science.gov (United States)

2011-09-28

...-0029] RIN 1615-AA90 Treatment of Aliens Whose Employment Creation Immigrant (EB-5) Petitions Were... qualifying aliens whose employment-creation immigrant petitions were approved by the former Immigration and...-273 Provisions C. Summary of the Adjudications Required by Public Law 107-273 III. Aliens Eligible To...

GTSE1 is a microtubule plus-end tracking protein that regulates EB1-dependent cell migration.

Directory of Open Access Journals (Sweden)

Massimilano Scolz

Full Text Available The regulation of cell migration is a highly complex process that is often compromised when cancer cells become metastatic. The microtubule cytoskeleton is necessary for cell migration, but how microtubules and microtubule-associated proteins regulate multiple pathways promoting cell migration remains unclear. Microtubule plus-end binding proteins (+TIPs are emerging as important players in many cellular functions, including cell migration. Here we identify a +TIP, GTSE1, that promotes cell migration. GTSE1 accumulates at growing microtubule plus ends through interaction with the EB1+TIP. The EB1-dependent +TIP activity of GTSE1 is required for cell migration, as well as for microtubule-dependent disassembly of focal adhesions. GTSE1 protein levels determine the migratory capacity of both nontransformed and breast cancer cell lines. In breast cancers, increased GTSE1 expression correlates with invasive potential, tumor stage, and time to distant metastasis, suggesting that misregulation of GTSE1 expression could be associated with increased invasive potential.

76 FR 61288 - Treatment of Aliens Whose Employment Creation Immigrant (EB-5) Petitions Were Approved After...

Science.gov (United States)

2011-10-04

... DEPARTMENT OF HOMELAND SECURITY 8 CFR Parts 216 and 245 [CIS No. 2484-09; Docket No. USCIS-2009-0029] RIN 1615-AA90 Treatment of Aliens Whose Employment Creation Immigrant (EB-5) Petitions Were... corrects an inadvertent error contained in the proposed rule titled Treatment of Aliens Whose Employment...

Studies on curing effect of phosphite monomer by EB radiation in the air

International Nuclear Information System (INIS)

Xiao, B.; Zhou, Y.; Li, S.; Luo, M.; Wang, X.; Zhao, P.

2000-01-01

A new type phosphite active monomer was synthesized. The resisting oxygen inhibition effect of this monomer and the effects of irradiation dose and concentration of phosphite active monomer on curing were studied. At the same time, curing results were analysed, through gel content and IR spectrum. The excellent resisting oxygen inhibition result of this phosphite active monomer was shown by experiments. EB radiation curing in the air was successfully carried out by the phosphite active monomer. (author)

A mutation of the fission yeast EB1 overcomes negative regulation by phosphorylation and stabilizes microtubules

International Nuclear Information System (INIS)

Iimori, Makoto; Ozaki, Kanako; Chikashige, Yuji; Habu, Toshiyuki; Hiraoka, Yasushi; Maki, Takahisa; Hayashi, Ikuko; Obuse, Chikashi; Matsumoto, Tomohiro

2012-01-01

Mal3 is a fission yeast homolog of EB1, a plus-end tracking protein (+ TIP). We have generated a mutation (89R) replacing glutamine with arginine in the calponin homology (CH) domain of Mal3. Analysis of the 89R mutant in vitro has revealed that the mutation confers a higher affinity to microtubules and enhances the intrinsic activity to promote the microtubule-assembly. The mutant Mal3 is no longer a + TIP, but binds strongly the microtubule lattice. Live cell imaging has revealed that while the wild type Mal3 proteins dissociate from the tip of the growing microtubules before the onset of shrinkage, the mutant Mal3 proteins persist on microtubules and reduces a rate of shrinkage after a longer pausing period. Consequently, the mutant Mal3 proteins cause abnormal elongation of microtubules composing the spindle and aster. Mal3 is phosphorylated at a cluster of serine/threonine residues in the linker connecting the CH and EB1-like C-terminal motif domains. The phosphorylation occurs in a microtubule-dependent manner and reduces the affinity of Mal3 to microtubules. We propose that because the 89R mutation is resistant to the effect of phosphorylation, it can associate persistently with microtubules and confers a stronger stability of microtubules likely by reinforcing the cylindrical structure. -- Highlights: ► We characterize a mutation (mal3-89R) in fission yeast homolog of EB1. ► The mutation enhances the activity to assemble microtubules. ► Mal3 is phosphorylated in a microtubule-dependent manner. ► The phosphorylation negatively regulates the Mal3 activity.

A mutation of the fission yeast EB1 overcomes negative regulation by phosphorylation and stabilizes microtubules

Energy Technology Data Exchange (ETDEWEB)

Iimori, Makoto; Ozaki, Kanako [Graduate School of Biostudies, Kyoto University, Kitashirakawa-Oiwake cho, Sakyo ku, Kyoto, 606-8502 (Japan); Chikashige, Yuji [Kobe Advanced ICT Research Center, National Institute of Information and Communications Technology, Kobe, 651-2492 (Japan); Habu, Toshiyuki [Graduate School of Biostudies, Kyoto University, Kitashirakawa-Oiwake cho, Sakyo ku, Kyoto, 606-8502 (Japan); Radiation Biology Center, Kyoto University, Yoshida-Konoe cho, Sakyo ku, Kyoto, 606-8501 (Japan); Hiraoka, Yasushi [Kobe Advanced ICT Research Center, National Institute of Information and Communications Technology, Kobe, 651-2492 (Japan); Graduate School of Frontier Biosciences, Osaka University, 1-3 Yamadaoka, Suita, 565-0871 (Japan); Maki, Takahisa; Hayashi, Ikuko [Graduate School of Nanobioscience, Yokohama City University, Tsurumi, Yokohama, 230-0045 (Japan); Obuse, Chikashi [Graduate School of Life Science, Hokkaido University, Sapporo 001-0021 (Japan); Matsumoto, Tomohiro, E-mail: tmatsumo@house.rbc.kyoto-u.ac.jp [Graduate School of Biostudies, Kyoto University, Kitashirakawa-Oiwake cho, Sakyo ku, Kyoto, 606-8502 (Japan); Radiation Biology Center, Kyoto University, Yoshida-Konoe cho, Sakyo ku, Kyoto, 606-8501 (Japan)

2012-02-01

Mal3 is a fission yeast homolog of EB1, a plus-end tracking protein (+ TIP). We have generated a mutation (89R) replacing glutamine with arginine in the calponin homology (CH) domain of Mal3. Analysis of the 89R mutant in vitro has revealed that the mutation confers a higher affinity to microtubules and enhances the intrinsic activity to promote the microtubule-assembly. The mutant Mal3 is no longer a + TIP, but binds strongly the microtubule lattice. Live cell imaging has revealed that while the wild type Mal3 proteins dissociate from the tip of the growing microtubules before the onset of shrinkage, the mutant Mal3 proteins persist on microtubules and reduces a rate of shrinkage after a longer pausing period. Consequently, the mutant Mal3 proteins cause abnormal elongation of microtubules composing the spindle and aster. Mal3 is phosphorylated at a cluster of serine/threonine residues in the linker connecting the CH and EB1-like C-terminal motif domains. The phosphorylation occurs in a microtubule-dependent manner and reduces the affinity of Mal3 to microtubules. We propose that because the 89R mutation is resistant to the effect of phosphorylation, it can associate persistently with microtubules and confers a stronger stability of microtubules likely by reinforcing the cylindrical structure. -- Highlights: Black-Right-Pointing-Pointer We characterize a mutation (mal3-89R) in fission yeast homolog of EB1. Black-Right-Pointing-Pointer The mutation enhances the activity to assemble microtubules. Black-Right-Pointing-Pointer Mal3 is phosphorylated in a microtubule-dependent manner. Black-Right-Pointing-Pointer The phosphorylation negatively regulates the Mal3 activity.

S-Lagrangian dynamics of many-body systems and behavior of social groups: Dominance and hierarchy formation

Science.gov (United States)

Sandler, U.

2017-11-01

In this paper, we extend our generalized Lagrangian dynamics (i.e., S-Lagrangian dynamics, which can be applied equally to physical and non-physical systems as per Sandler (2014)) to many-body systems. Unlike common Lagrangian dynamics, this is not a trivial task. For many-body systems with S-dependent Lagrangians, the Lagrangian and the corresponding Hamiltonian or energy become vector functions, conjugated momenta become second-order tensors, and the system inevitably develops a hierarchical structure, even if all bodies initially have similar status and Lagrangians. As an application of our theory, we consider dominance and hierarchy formation, which is present in almost all communities of living species. As a biological basis for this application, we assume that the primary motivation of a groups activity is to attempt to cope with stress arising as pressure from the environment and from intrinsic unmet needs of individuals. It has been shown that the S-Lagrangian approach to a group's evolution naturally leads to formation of linear or despotic dominance hierarchies, depending on differences between individuals in coping with stress. That is, individuals that cope more readily with stress take leadership roles during the evolution. Experimental results in animal groups which support our assumption and findings are considered.

Development of Ground Test System For RKX-200EB

Science.gov (United States)

Yudhi Irwanto, Herma

2018-04-01

After being postponed for seven years, the development of RKX-200EB now restarts by initiating a ground test, preceding the real flight test. The series of the development starts from simulation test using the real vehicle and its components, focusing on a flight sequence test using hardware in the loop simulation. The result of the simulation shows that the autonomous control system in development is able to control the X tail fin vehicle, since take off using booster, separating booster-sustainer, making flight maneuver using sustainer with average cruise speed of 1000 km/h, and doing bank to maneuver up to ±40 deg heading to the target. The simulation result also shows that the presence of sustainer in vehicle control can expand the distance range by 162% (12.6 km) from its ballistic range using only a booster.

[Heinike Heinsoo. Mā ja pūd lēväd, meid eb lē] / Fedor Rozhanskiy

Index Scriptorium Estoniae

Rozhanskiy, Fedor

2013-01-01

Arvustus: Heinike Heinsoo. Mā ja pūd lēväd, meid eb lē : the subject and the predicate in Votic. Tallinn : Teaduste Akadeemia Kirjastus, 2010. (Linguistica Uralica. Supplementary series ; vol. 4)

XML-BSPM: an XML format for storing Body Surface Potential Map recordings.

Science.gov (United States)

Bond, Raymond R; Finlay, Dewar D; Nugent, Chris D; Moore, George

2010-05-14

The Body Surface Potential Map (BSPM) is an electrocardiographic method, for recording and displaying the electrical activity of the heart, from a spatial perspective. The BSPM has been deemed more accurate for assessing certain cardiac pathologies when compared to the 12-lead ECG. Nevertheless, the 12-lead ECG remains the most popular ECG acquisition method for non-invasively assessing the electrical activity of the heart. Although data from the 12-lead ECG can be stored and shared using open formats such as SCP-ECG, no open formats currently exist for storing and sharing the BSPM. As a result, an innovative format for storing BSPM datasets has been developed within this study. The XML vocabulary was chosen for implementation, as opposed to binary for the purpose of human readability. There are currently no standards to dictate the number of electrodes and electrode positions for recording a BSPM. In fact, there are at least 11 different BSPM electrode configurations in use today. Therefore, in order to support these BSPM variants, the XML-BSPM format was made versatile. Hence, the format supports the storage of custom torso diagrams using SVG graphics. This diagram can then be used in a 2D coordinate system for retaining electrode positions. This XML-BSPM format has been successfully used to store the Kornreich-117 BSPM dataset and the Lux-192 BSPM dataset. The resulting file sizes were in the region of 277 kilobytes for each BSPM recording and can be deemed suitable for example, for use with any telemonitoring application. Moreover, there is potential for file sizes to be further reduced using basic compression algorithms, i.e. the deflate algorithm. Finally, these BSPM files have been parsed and visualised within a convenient time period using a web based BSPM viewer. This format, if widely adopted could promote BSPM interoperability, knowledge sharing and data mining. This work could also be used to provide conceptual solutions and inspire existing formats

76 FR 75562 - Notice of a Change in Status of an Extended Benefit (EB) Period for Pennsylvania

Science.gov (United States)

2011-12-02

... Extended Benefit (EB) Period for Pennsylvania AGENCY: Employment and Training Administration, Labor. ACTION... Pennsylvania. The following changes have occurred since the publication of the last notice regarding the State... three month average, seasonally- adjusted total unemployment rate for Pennsylvania rose to exceed the 8...

The control of fruiting body formation in the ascomycete Sordaria macrospora Auersw. by arginine and biotin: a two-factor analysis.

Science.gov (United States)

Molowitz, R; Bahn, M; Hock, B

1976-01-01

Fruiting body formation of Sordaria macrospora Auersw. is controlled by L-arginine and biotin when the fungus is grown on a synthetic nutrient medium containing optimal concentrations of fructose, KNO3, KH2PO4, MgSO4, and ZnSO4. Arginine and biotin operate in very low concentrations which exclude unspecific nutrient effects. In spite of the complicated interactions of arginine and biotin which are shown qualitatively (Figs. 3 and 4a) and quantitatively (Figs. 2 and 4b), the following conclusions are reached: 1. In the absence of biotin, the development of Sordaria macrospora is blocked at the stage of small protoperithecia. The external addition of biotin (optimal concentration: 3-12 μg/l) allows the formation of fertile fruiting bodies. This effect cannot be imitated by arginine. The biotin effect is discussed in connection with stimulated RNA synthesis.-2. The developmental velocity is influenced by the external addition of arginine. Without arginine but at permissible biotin concentrations, the total life cycle takes about 10 days, in the presence of arginine (1 mM), however, about 6 days.-3. The hyphal density, as well as the total number of fruiting bodies being produced, is controlled in a similar manner by biotin and arginine. The induction of fruiting body formation obviously takes place after the transgression of a critical hyphal density.

Turning snails into slugs: induced body plan changes and formation of an internal shell.

Science.gov (United States)

Osterauer, Raphaela; Marschner, Leonie; Betz, Oliver; Gerberding, Matthias; Sawasdee, Banthita; Cloetens, Peter; Haus, Nadine; Sures, Bernd; Triebskorn, Rita; Köhler, Heinz-R

2010-01-01

The archetypal body plan of conchiferan molluscs is characterized by an external calcareous shell, though internalization of shells has evolved independently in a number of molluscan clades, including gastropod families. In gastropods, the developmental process of torsion is regarded as a hallmark that is associated with a new anatomical configuration. This configuration is present in extant prosobranch gastropod species, which predominantly bear external shells. Here, we show that short-term exposure to platinum during development uncouples at least two of the processes associated with torsion of the freshwater snail Marisa cornuarietis. That is, the anus of the treated snails is located anteriorly, but the gill and the designated mantle tissue remains in a posterior location, thus preventing the formation of an external shell. In contrast to the prosobranchian archetype, platinum treatment results in the formation of a posterior gill and a cone-shaped internal shell, which persists across the lifetime. This first finding of artificially induced snail-slug conversion was also seen in the pulmonate snail Planorbarius corneus and demonstrates that selective alteration of embryonic key processes can result in fundamental changes of an existing body plan and-if altered regulation is inherited-may give rise to a new one. © 2010 Wiley Periodicals, Inc.

Applied socio-hydrology using volunteer geographic information (VGI) to integrate ecosystem-based adaptation (EbA) and disaster risk reduction (DRR)

Science.gov (United States)

Mendiondo, Eduardo; Taffarello, Denise; Mohor, Guilherme; Guzmán, Diego; Câmara de Freitas, Clarissa; Fava, Maria Clara; Restrepo, Camilo; Abreu, Fernando; Batalini, Marina; Lago, Cesar; Abe, Narumi; Rosa, Altair

2017-04-01

Socio-hydrology proposes to understand coupled human-water systems by conceptualizing its components to be dynamically connected by bi-directional feedbacks. For practical purposes, especially in developing countries of South America, socio-hydrology does integrate practical, empirical and theoretical fundamentals from citizens' knowledge and culture. This contribution shows South American examples of how volunteer geographic information (VGI) can help socio-hydrology to integrate emerging aspects with heavy feedbacks, exploding uncertainties and relevant scales of socio-hydrological scales. Here we select examples at different scales of using VGI to link aspects of ecosystem-based adaptation (EbA) and disaster risk reduction (DRR). On the one hand, we show some learning cases of EbA/VGI linked to socio-hydrology also related with water valuation, both monetary and non-monetary, under scenarios of changing conditions of land-use and land cover changes of strategic water supply systems in subtropical biomes. This example brings a bridge of VGI and EbA towards Disaster Risk Reduction (DRR) through water topics of securitization, insurance, smart cities and sustainable urban drainage systems (SUDS). Thus, on the other hand, we also depict how VGI support applied elements for socio-hydrology on South American urban areas, capable of policy actions for DRR through SUDS at human-impacted biomes under extremes of droughts, floods and pollution. We here recommend yardsticks of learning conditions from these real examples of using VGI's knowledge and culture biases for a more resilient socio-hydrology, in order to create opportunities for theoretical, conceptual and applied nature of EbA and DRR with viable alliances from IAHS/Panta Rhei with UN/Sendai/DRR Framework and UN/Sustainable Development Goals. From these examples, however, seem plausible co-evolutionary dynamics with stakeholders if local-scale constraints, from sociopolitical nature, institutions' policies and

Standard practice for prediction of the long-term behavior of materials, including waste forms, used in engineered barrier systems (EBS) for geological disposal of high-level radioactive waste

CERN Document Server

American Society for Testing and Materials. Philadelphia

2007-01-01

1.1 This practice describes test methods and data analyses used to develop models for the prediction of the long-term behavior of materials, such as engineered barrier system (EBS) materials and waste forms, used in the geologic disposal of spent nuclear fuel (SNF) and other high-level nuclear waste in a geologic repository. The alteration behavior of waste form and EBS materials is important because it affects the retention of radionuclides by the disposal system. The waste form and EBS materials provide a barrier to release either directly (as in the case of waste forms in which the radionuclides are initially immobilized), or indirectly (as in the case of containment materials that restrict the ingress of groundwater or the egress of radionuclides that are released as the waste forms and EBS materials degrade). 1.1.1 Steps involved in making such predictions include problem definition, testing, modeling, and model confirmation. 1.1.2 The predictions are based on models derived from theoretical considerat...

Evaluation of Tc-99M labeled ethylene diamine tetra acetic acid biotin monomer (EB1) as an inflammation imaging agent

International Nuclear Information System (INIS)

Imran, M.B.; Qaiser, I.; Jehangir, M.; Irfan, J.

2004-01-01

Objective:This study was aimed at the evaluation of EB1 as an inflammation-imaging agent in animal models after ascertaining its normal biodistribution. Methods: Kit was formulated by adding SnC12 as reducing agent in EB 1 compound. EDTA was used as chelating agent. Buffer was added to lower the pH of solution to 5. Freeze dried kits were prepared for later use in experiments. Kits were reconstituted with 0.5 ml of fresh eluate of 99m-TcO4 containing total activity of about 370 MBq. Radiochemical quality control was checked by conventional strip method using double solvent technique.Biodistribution was assessed in 15 Sprague Dawley rats. An injection of 10 MBq was given in tail vein in each animal. Animals were killed at pre-specified time intervals; organs were separated, weighed and counted. Counts recovered were corrected for decay. Inflammation models were prepared by injecting turpentine oil in the thigh muscles of 14 rabbits. In one rabbit inflammation was not induced and was used as control for EB 1. In 3 of inflammation models plain 99m-TcO4 was injected (control II). In another group of 3 animals 99m-TC-EDTA was injected (control II). In the last group of 8 animals 99m-TcO4-EB 1 was injected (experimental gp). Animals were serially imaged under Seimens' E-Cam gamma camera for the distribution of activity in different organs and at the site of inflammation. Results: Kit labeling efficiency was 90.5 + 2.5% with 2.5 + 0.8% free activity and 7 + 1.1% hydrolyzed form. Animal study on rats showed that pharmaceutical is mainly excreted by kidneys (51.57 + 9.2% at 15 minutes and 81.73 + 7.9% at 4 hours). Uptake in liver was 7.52 + 2.2% at 15 minutes that decreased to 2.3 + 0.5% at 4 hours. Activity in intestine increased from 5.48 + 2.9% to 7.05 + 1.6% at 15 minutes to 4 hours. Activity in background (=blood) decreased from 0.13% (at 15 minutes) to 0.04% at 4 hrs. In bones EB1 uptake decreased from 0.68% to 0.15% at 15 minutes to 4 hours. In inflammation models

Comparison between Duncan and Chang’s EB Model and the Generalized Plasticity Model in the Analysis of a High Earth-Rockfill Dam

Directory of Open Access Journals (Sweden)

Weixin Dong

2013-01-01

Full Text Available Nonlinear elastic model and elastoplastic model are two main kinds of constitutive models of soil, which are widely used in the numerical analyses of soil structure. In this study, Duncan and Chang's EB model and the generalized plasticity model proposed by Pastor, Zienkiewicz, and Chan was discussed and applied to describe the stress-strain relationship of rockfill materials. The two models were validated using the results of triaxial shear tests under different confining pressures. The comparisons between the fittings of models and test data showed that the modified generalized plasticity model is capable of simulating the mechanical behaviours of rockfill materials. The modified generalized plasticity model was implemented into a finite element code to carry out static analyses of a high earth-rockfill dam in China. Nonlinear elastic analyses were also performed with Duncan and Chang's EB model in the same program framework. The comparisons of FEM results and in situ monitoring data showed that the modified PZ-III model can give a better description of deformation of the earth-rockfill dam than Duncan and Chang’s EB model.

Advanced neutron and X-ray techniques for insights into the microstructure of EB-PVD thermal barrier coatings

Energy Technology Data Exchange (ETDEWEB)

Kulkarni, Anand [State University of New York, Stony Brook, NY 11794 (United States); Goland, Allen [State University of New York, Stony Brook, NY 11794 (United States); Herman, Herbert [State University of New York, Stony Brook, NY 11794 (United States)]. E-mail: hherman@ms.cc.sunysb.edu; Allen, Andrew J. [National Institute of Standards and Technology, Gaithersburg, MD 20899 (United States); Dobbins, Tabbetha [National Institute of Standards and Technology, Gaithersburg, MD 20899 (United States); DeCarlo, Francesco [Argonne National Laboratory, Argonne, IL 60439 (United States); Ilavsky, Jan [Argonne National Laboratory, Argonne, IL 60439 (United States); Long, Gabrielle G. [Argonne National Laboratory, Argonne, IL 60439 (United States); Fang, Stacy [Chromalloy Gas Turbine Corporation, Orangeburg, NY 10962 (United States); Lawton, Paul [Chromalloy Gas Turbine Corporation, Orangeburg, NY 10962 (United States)

2006-06-25

The ongoing quest to increase gas turbine efficiency and performance (increased thrust) provides a driving force for materials development. While improved engine design and usage of novel materials provide solutions for increased engine operating temperatures, and hence fuel efficiency, reliability issues remain. Thermal barrier coatings (TBCs), deposited onto turbine components using the electron-beam physical vapor deposition (EB-PVD) process, exhibit unique pore architectures capable of bridging the technological gap between insulation/life extension and prime reliance. This article explores the potential of advanced X-ray and neutron techniques for comprehension of an EB-PVD TBC coating microstructure. While conventional microscopy reveals a hierarchy of voids, complementary advanced techniques allow quantification of these voids in terms of component porosities, anisotropy, size and gradient through the coating thickness. In addition, the derived microstructural parameters obtained both further knowledge of the nature and architecture of the porosity, and help establish its influence on the resultant thermal and mechanical properties.

Residual stress measurement of EB-welded plates with contour method. Part 2: FEM analysis of contour profiles

International Nuclear Information System (INIS)

Romppanen, A.-J.; Immonen, E.

2013-12-01

The residual stresses formed as a result of Electronic Beam welding (EB-welding) in copper are investigated by Posiva. In the present study, residual stresses of EB-welded copper plates were studied with contour method. In the method eleven copper plates (X436 - X440 and X453 - X458) were cut in half with wire electric discharge machining (EDM) after which the deformation due to stress relaxation was measured with coordinate measurement system. The measured data was then used as boundary displacement data for the FEM analyses, in which the corresponding residual stresses were calculated. Before giving the corresponding displacement boundary conditions to the FE models, the deformation data was processed and smoothed appropriately. The residual stress levels of the copper plates were found to be around 40 - 55 MPa at maximum. This corresponds to other reported residual stress measurements and current state of knowledge with this material in Posiva. (orig.)

Evaluating controls on fluvial sand-body clustering in the Ferris Formation (Cretaceous/Paleogene, Wyoming, USA)

Science.gov (United States)

Hajek, E. A.; Heller, P.

2009-12-01

A primary goal of sedimentary geologists is to interpret past tectonic, climatic, and eustatic conditions from the stratigraphic record. Stratigraphic changes in alluvial-basin fills are routinely interpreted as the result of past tectonic movements or changes in climate or sea level. Recent physical and numerical models have shown that sedimentary systems can exhibit self-organization on basin-filling time scales, suggesting that structured stratigraphic patterns can form spontaneously rather than as the result of changing boundary conditions. The Ferris Formation (Upper Cretaceous/Paleogene, Hanna Basin, Wyoming) exhibits stratigraphic organization where clusters of closely-spaced channel deposits are separated from other clusters by intervals dominated by overbank material. In order to evaluate the role of basinal controls on deposition and ascertain the potential for self-organization in this ancient deposit, the spatial patterns of key channel properties (including sand-body dimensions, paleoflow depth, maximum clast size, paleocurrent direction, and sediment provenance) are analyzed. Overall the study area lacks strong trends sand-body properties through the stratigraphic succession and in cluster groups. Consequently there is no indication that the stratigraphic pattern observed in the Ferris Formation was driven by systematic changes in climate or tectonics.

A NEW HYBRID N-BODY-COAGULATION CODE FOR THE FORMATION OF GAS GIANT PLANETS

International Nuclear Information System (INIS)

Bromley, Benjamin C.; Kenyon, Scott J.

2011-01-01

We describe an updated version of our hybrid N-body-coagulation code for planet formation. In addition to the features of our 2006-2008 code, our treatment now includes algorithms for the one-dimensional evolution of the viscous disk, the accretion of small particles in planetary atmospheres, gas accretion onto massive cores, and the response of N-bodies to the gravitational potential of the gaseous disk and the swarm of planetesimals. To validate the N-body portion of the algorithm, we use a battery of tests in planetary dynamics. As a first application of the complete code, we consider the evolution of Pluto-mass planetesimals in a swarm of 0.1-1 cm pebbles. In a typical evolution time of 1-3 Myr, our calculations transform 0.01-0.1 M sun disks of gas and dust into planetary systems containing super-Earths, Saturns, and Jupiters. Low-mass planets form more often than massive planets; disks with smaller α form more massive planets than disks with larger α. For Jupiter-mass planets, masses of solid cores are 10-100 M + .

Coupling gene expression and multicellular morphogenesis during fruiting body formation in Myxococcus xanthus

DEFF Research Database (Denmark)

Søgaard-Andersen, L.; Overgaard, M.; Lobedanz, S.

2003-01-01

xanthus illustrates this coupling in the construction of a multicellular structure. Fruiting body formation involves two stages: aggregation of cells into mounds and the position-specific sporulation of cells that have accumulated inside mounds. Developmental gene expression propels these two processes...... morphogenesis. Accumulation of the C-signal is tightly regulated and involves transcriptional activation of the csgA gene and proteolysis of the full-length CsgA protein to produce the shorter cell surface-associated 17 kDa C-signal protein. The C-signal induces aggregation, sporulation and developmental gene...

Neural Differentiation in HDAC1-Depleted Cells Is Accompanied by Coilin Downregulation and the Accumulation of Cajal Bodies in Nucleoli

Czech Academy of Sciences Publication Activity Database

Krejčí, Jana; Legartová, Soňa; Bártová, Eva

2017-01-01

Roč. 2017, č. 2017 (2017), č. článku 1021240. E-ISSN 1687-9678 R&D Projects: GA ČR GBP302/12/G157; GA MŠk 7F14369 Institutional support: RVO:68081707 Keywords : embryonic stem-cells * body * organization Subject RIV: EB - Genetics ; Molecular Biology OBOR OECD: Cell biology

The control of fruiting body formation in the ascomycete Sordaria macrospora Auersw. by regulation of hyphal development : An analysis based on scanning electron and light microscopic observations.

Science.gov (United States)

Hock, B; Bahn, M; Walk, R A; Nitschke, U

1978-01-01

The morphological effects of biotin and L-arginine on fruiting body formation of the ascomycete Sordaria macrospora are investigated by scanning electron and light microscopy. Biotin is recognized as an elongation factor and arginine as a branching factor in vegetative and reproductive hyphae. In the absence of exogenous biotin, development is blocked after the ascogonium-core hypha stage of protoperithecial morphogenesis, whereas linear growth of the myceliar front is maintained. The addition of exogenous arginine to a biotin deficient culture induces the formation of numerous side branches even in the older mycelium. Fruiting body formation, however, remains blocked at the protoperithecial stage as before, because of the inability of the side branches to elongate. When biotin and arginine are administered simultaneously, a most vigorous branching and growth are induced in the older mycelium, accompanied by a rapid and maximal formation of fruiting bodies. The results are summarized in a model of the exogenous control of hyphal morphogenesis. The model is designed to explain the relationship between fruiting and hyphal density as well as the edge effect on fruiting body formation.

GCN5 Regulates FGF Signaling and Activates Selective MYC Target Genes during Early Embryoid Body Differentiation

Directory of Open Access Journals (Sweden)

Li Wang

2018-01-01

Full Text Available Precise control of gene expression during development is orchestrated by transcription factors and co-regulators including chromatin modifiers. How particular chromatin-modifying enzymes affect specific developmental processes is not well defined. Here, we report that GCN5, a histone acetyltransferase essential for embryonic development, is required for proper expression of multiple genes encoding components of the fibroblast growth factor (FGF signaling pathway in early embryoid bodies (EBs. Gcn5−/− EBs display deficient activation of ERK and p38, mislocalization of cytoskeletal components, and compromised capacity to differentiate toward mesodermal lineage. Genomic analyses identified seven genes as putative direct targets of GCN5 during early differentiation, four of which are cMYC targets. These findings established a link between GCN5 and the FGF signaling pathway and highlighted specific GCN5-MYC partnerships in gene regulation during early differentiation.

Development of radiation curable surface coating based on soybean oil. part II: Evaluation of the prepared acrylated resin as surface coatings by using EB or UV sources for radiation curing applications

International Nuclear Information System (INIS)

Ibrahim, M.S.; Said, H.M.; Moussa, I.M.

2005-01-01

In recent years, there has been a growing trend in using vegetable oils as raw materials in acylation production that can be cured by UV/EB systems. The acrylated resin formulates by using individually different functional acrylate monomers were prepared and cured by EB or UV sources. The characterization properties of the cured films were investigated in terms of pendulum hardness, bending, impact, gloss, adhesion and chemical tests. Other formulations were prepared by mixing a constant ratio of different functional acrylate monomers and exposed to UV or EB irradiation. The results showed that the hardness of cured films were increased by increasing the functionality of monomers with excellent adhesion for all formulations but at expense of other properties involving bending and impact tests. Therefore, it can be deduce that the hardness of the curing surface coating by using EB was found to be nearly twice the hardness of the curing surface coating by using UV irradiation. Also, the best formulations which have given good chemical and mechanical properties are (mono-di) functional acrylate monomer resin under EB and (mono-tri) functional acrylate monomer resin under UV irradiation

Monostotic fibrous dysplasia of a lumbar vertebral body with secondary aneurysmal bone cyst formation: a case report

Directory of Open Access Journals (Sweden)

Snieders Marieke N

2009-06-01

Full Text Available Abstract We report the case of a 25-year-old Caucasian woman with symptomatic monostotic fibrous dysplasia of the fourth lumbar vertebral body. The patient suffered from a five-week history of progressive low back pain, radiating continuously to the left leg. Her medical history and physical and neurological examination did not demonstrate any significant abnormalities. Radiographs, computed tomography and magnetic resonance imaging revealed an osteolytic expansive lesion with a cystic component of the fourth lumbar vertebral body. Percutaneous transpedicular biopsy showed histological characteristics of fibrous dysplasia superimposed by the formation of aneurysmal bone cyst components. The patient was treated by subtotal vertebrectomy of the L4 vertebral body with anterior reconstruction and her postoperative course was uncomplicated. To our knowledge, this is the first reported case of a monostotic fibrous dysplasia with superimposed secondary aneurysmal bone cysts of a lumbar vertebral body.

Sandstone-body and shale-body dimensions in a braided fluvial system: Salt wash sandstone member (Morrison formation), Garfield County, Utah

Science.gov (United States)

Robinson, J.W.; McCabea, P.J.

1997-01-01

Excellent three-dimensional exposures of the Upper Jurassic Salt Wash Sandstone Member of the Morrison Formation in the Henry Mountains area of southern Utah allow measurement of the thickness and width of fluvial sandstone and shale bodies from extensive photomosaics. The Salt Wash Sandstone Member is composed of fluvial channel fill, abandoned channel fill, and overbank/flood-plain strata that were deposited on a broad alluvial plain of low-sinuosity, sandy, braided streams flowing northeast. A hierarchy of sandstone and shale bodies in the Salt Wash Sandstone Member includes, in ascending order, trough cross-bedding, fining-upward units/mudstone intraclast conglomerates, singlestory sandstone bodies/basal conglomerate, abandoned channel fill, multistory sandstone bodies, and overbank/flood-plain heterolithic strata. Trough cross-beds have an average width:thickness ratio (W:T) of 8.5:1 in the lower interval of the Salt Wash Sandstone Member and 10.4:1 in the upper interval. Fining-upward units are 0.5-3.0 m thick and 3-11 m wide. Single-story sandstone bodies in the upper interval are wider and thicker than their counterparts in the lower interval, based on average W:T, linear regression analysis, and cumulative relative frequency graphs. Multistory sandstone bodies are composed of two to eight stories, range up to 30 m thick and over 1500 m wide (W:T > 50:1), and are also larger in the upper interval. Heterolithic units between sandstone bodies include abandoned channel fill (W:T = 33:1) and overbank/flood-plain deposits (W:T = 70:1). Understanding W:T ratios from the component parts of an ancient, sandy, braided stream deposit can be applied in several ways to similar strata in other basins; for example, to (1) determine the width of a unit when only the thickness is known, (2) create correlation guidelines and maximum correlation lengths, (3) aid in interpreting the controls on fluvial architecture, and (4) place additional constraints on input variables to

Metabolic features of Protochlamydia amoebophila elementary bodies--a link between activity and infectivity in Chlamydiae.

Directory of Open Access Journals (Sweden)

Barbara S Sixt

Full Text Available The Chlamydiae are a highly successful group of obligate intracellular bacteria, whose members are remarkably diverse, ranging from major pathogens of humans and animals to symbionts of ubiquitous protozoa. While their infective developmental stage, the elementary body (EB, has long been accepted to be completely metabolically inert, it has recently been shown to sustain some activities, including uptake of amino acids and protein biosynthesis. In the current study, we performed an in-depth characterization of the metabolic capabilities of EBs of the amoeba symbiont Protochlamydia amoebophila. A combined metabolomics approach, including fluorescence microscopy-based assays, isotope-ratio mass spectrometry (IRMS, ion cyclotron resonance Fourier transform mass spectrometry (ICR/FT-MS, and ultra-performance liquid chromatography mass spectrometry (UPLC-MS was conducted, with a particular focus on the central carbon metabolism. In addition, the effect of nutrient deprivation on chlamydial infectivity was analyzed. Our investigations revealed that host-free P. amoebophila EBs maintain respiratory activity and metabolize D-glucose, including substrate uptake as well as host-free synthesis of labeled metabolites and release of labeled CO2 from (13C-labeled D-glucose. The pentose phosphate pathway was identified as major route of D-glucose catabolism and host-independent activity of the tricarboxylic acid (TCA cycle was observed. Our data strongly suggest anabolic reactions in P. amoebophila EBs and demonstrate that under the applied conditions D-glucose availability is essential to sustain metabolic activity. Replacement of this substrate by L-glucose, a non-metabolizable sugar, led to a rapid decline in the number of infectious particles. Likewise, infectivity of Chlamydia trachomatis, a major human pathogen, also declined more rapidly in the absence of nutrients. Collectively, these findings demonstrate that D-glucose is utilized by P. amoebophila

The status of UV/EB curable product in North America: 1998-1999

International Nuclear Information System (INIS)

Lawson, K.

1999-01-01

This author has previously reported survey results showing that the use of UV/EB materials has grown at a compound rate of about 10% per annum over the last decade. Together, with about 130 members of RadTech International North America, representing 90 organizations, we have updated and assessed the growth and activities of the industry. The panelists represent a cross section of end users, raw material and equipment suppliers, as well as formulators and consultants. Using a modified Delphi process with five separate survey rounds, a reasonable assessment was made of the advantages, disadvantages, growth rate and growth opportunities of this exciting technology

Relation of Thermal Conductivity with Process Induced Anisotropic Void Systems in EB-PVD PYSZ Thermal Barrier Coatings

Energy Technology Data Exchange (ETDEWEB)

Renteria, A. Flores; Saruhan-Brings, B.; Ilavsky, J.

2008-03-03

Thermal barrier coatings (TBCs) deposited by Electron-beam physical deposition (EB-PVD) protect the turbine blades situated at the high pressure sector of the aircraft and stationary turbines. It is an important task to uphold low thermal conductivity in TBCs during long-term service at elevated temperatures. One of the most promising methods to fulfil this task is to optimize the properties of PYSZ-based TBC by tailoring its microstructure. Thermal conductivity of the EB-PVD produced PYSZ TBCs is influenced mainly by the size, shape, orientation and volume of the various types of porosity present in the coatings. These pores can be classified as open (inter-columnar and between feather arms gaps) and closed (intra-columnar pores). Since such pores are located within the three-dimensionally deposited columns and enclose large differences in their sizes, shapes, distribution and anisotropy, the accessibility for their characterization is very complex and requires the use of sophisticated methods. In this work, three different EB-PVD TBC microstructures were manufactured by varying the process parameters, yielding various characteristics of their pores. The corresponding thermal conductivities in as-coated state and after ageing at 11000C/1h and 100h were measured via Laser Flash Analysis Method (LFA). The pore characteristics and their individual effect on the thermal conductivity are analysed by USAXS which is supported by subsequent modelling and LFA methods, respectively. Evident differences in the thermal conductivity values of each microstructure were found in as-coated and aged conditions. In summary, broader columns introduce higher values in thermal conductivity. In general, thermal conductivity increases after ageing for all three investigated microstructures, although those with initial smaller pore surface area show smaller changes.

Relation of thermal conductivity with process induced anisotropic void system in EB-PVD PYSZ thermal barrier coatings.

Energy Technology Data Exchange (ETDEWEB)

Renteria, A. F.; Saruhan, B.; Ilavsky, J.; German Aerospace Center

2007-01-01

Thermal barrier coatings (TBCs) deposited by Electron-beam physical deposition (EB-PVD) protect the turbine blades situated at the high pressure sector of the aircraft and stationary turbines. It is an important task to uphold low thermal conductivity in TBCs during long-term service at elevated temperatures. One of the most promising methods to fulfil this task is to optimize the properties of PYSZ-based ,TBC by tailoring its microstructure. Thermal conductivity of the EB-PVD produced PYSZ TBCs is influenced mainly by the size, shape, orientation and volume of the various types of porosity present in the coatings. These pores can be classified as open (inter-columnar and between feather arms gaps) and closed (intra-columnar pores). Since such pores are located within the three-dimensionally deposited columns and enclose large differences in their sizes, shapes, distribution and anisotropy, the accessibility for their characterization is very complex and requires the use of sophisticated methods. In this work, three different EB-PVD TBC microstructures were manufactured by varying the process parameters, yielding various characteristics of their pores. The corresponding thermal conductivities in as-coated state and after ageing at 1100C/1h and 100h were measured via Laser Flash Analysis Method (LFA). The pore characteristics and their individual effect on the thermal conductivity are analysed by USAXS which is supported by subsequent modelling and LFA methods, respectively. Evident differences in the thermal conductivity values of each microstructure were found in as-coated and aged conditions. In summary, broader columns introduce higher values in thermal conductivity. In general, thermal conductivity increases after ageing for all three investigated microstructures, although those with initial smaller pore surface area show smaller changes.

The effect of thermal velocities on structure formation in N-body simulations of warm dark matter

Science.gov (United States)

Leo, Matteo; Baugh, Carlton M.; Li, Baojiu; Pascoli, Silvia

2017-11-01

We investigate the impact of thermal velocities in N-body simulations of structure formation in warm dark matter models. Adopting the commonly used approach of adding thermal velocities, randomly selected from a Fermi-Dirac distribution, to the gravitationally-induced velocities of the simulation particles, we compare the matter and velocity power spectra measured from CDM and WDM simulations, in the latter case with and without thermal velocities. This prescription for adding thermal velocities introduces numerical noise into the initial conditions, which influences structure formation. At early times, the noise affects dramatically the power spectra measured from simulations with thermal velocities, with deviations of the order of ~ Script O(10) (in the matter power spectra) and of the order of ~ Script O(102) (in the velocity power spectra) compared to those extracted from simulations without thermal velocities. At late times, these effects are less pronounced with deviations of less than a few percent. Increasing the resolution of the N-body simulation shifts these discrepancies to higher wavenumbers. We also find that spurious haloes start to appear in simulations which include thermal velocities at a mass that is ~3 times larger than in simulations without thermal velocities.

Recent geodynamic and geomorphological analyses of the Diendorf–Čebín Tectonic Zone, Czech Republic

Czech Academy of Sciences Publication Activity Database

Roštínský, Pavel; Pospíšil, L.; Švábenský, O.

2013-01-01

Roč. 599, 25. červen 2013 (2013), s. 45-66 ISSN 0040-1951 Grant - others:GA MŠk(CZ) ED2.1.00/03.0097 Institutional support: RVO:68145535 Keywords : Diendorf – Čebín Tectonic Zone * Bohemian Massif * recent movement Subject RIV: DE - Earth Magnetism, Geodesy, Geography Impact factor: 2.866, year: 2013 http://dx.doi.org/10.1016/j.tecto.2013.04.008

COLLISIONS BETWEEN GRAVITY-DOMINATED BODIES. II. THE DIVERSITY OF IMPACT OUTCOMES DURING THE END STAGE OF PLANET FORMATION

International Nuclear Information System (INIS)

Stewart, Sarah T.; Leinhardt, Zoë M.

2012-01-01

Numerical simulations of the stochastic end stage of planet formation typically begin with a population of embryos and planetesimals that grow into planets by merging. We analyzed the impact parameters of collisions leading to the growth of terrestrial planets from recent N-body simulations that assumed perfect merging and calculated more realistic outcomes using a new analytic collision physics model. We find that collision outcomes are diverse and span all possible regimes: hit-and-run, merging, partial accretion, partial erosion, and catastrophic disruption. The primary outcomes of giant impacts between planetary embryos are approximately evenly split between partial accretion, graze-and-merge, and hit-and-run events. To explore the cumulative effects of more realistic collision outcomes, we modeled the growth of individual planets with a Monte Carlo technique using the distribution of impact parameters from N-body simulations. We find that fewer planets reached masses >0.7 M Earth using the collision physics model compared to simulations that assumed every collision results in perfect merging. For final planets with masses >0.7 M Earth , 60% are enriched in their core-to-mantle mass fraction by >10% compared to the initial embryo composition. Fragmentation during planet formation produces significant debris (∼15% of the final mass) and occurs primarily by erosion of the smaller body in partial accretion and hit-and-run events. In partial accretion events, the target body grows by preferentially accreting the iron core of the projectile and the escaping fragments are derived primarily from the silicate mantles of both bodies. Thus, the bulk composition of a planet can evolve via stochastic giant impacts.

The Cajal body: a meeting place for spliceosomal snRNPs in the nuclear maze

Czech Academy of Sciences Publication Activity Database

Staněk, David; Neugebauer, K. M.

2006-01-01

Roč. 115, č. 5 (2006), s. 343-354 ISSN 0009-5915 R&D Projects: GA ČR(CZ) GA301/05/0601; GA MŠk(CZ) 1K05009; GA MŠk(CZ) LC535 Grant - others:GA-(DE) Max Planck Society; Deutsche Forschung Gemeinschaft(DE) NE909/1-1 Institutional research plan: CEZ:AV0Z50110509 Keywords : Cajal body * spliceosomal snRNP Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 4.065, year: 2006

Evidence for the characterization of heavy-ion reactions by the ratio E/B

International Nuclear Information System (INIS)

Mathews, G.J.; Wozniak, G.J.; Schmitt, R.P.; Moretto, L.G.

1977-01-01

The connection between the characteristic features of reactions involving very heavy target-projectile combinations (e.g. 86 Kr + 197 Au) and lighter systems (e.g. 40 Ar + sup(nat)Ag) is discussed. Evidence for an impirical scaling law based upon the ratio E/B (center-of-mass kinetic energy to Coulomb barrier) is presented. This scaling is justified in terms of semiquantitative arguments whereby the different charge and angular distribution patterns from light and heavy target-projectile combinations are correlated with different lifetime regimes for the 'intermediate complex' as it diffuses along the mass-asymmetry coordinate. (orig.) [de

Metabolic Features of Protochlamydia amoebophila Elementary Bodies – A Link between Activity and Infectivity in Chlamydiae

Science.gov (United States)

Watzka, Margarete; Wultsch, Anna; Tziotis, Dimitrios; Montanaro, Jacqueline; Richter, Andreas; Schmitt-Kopplin, Philippe; Horn, Matthias

2013-01-01

The Chlamydiae are a highly successful group of obligate intracellular bacteria, whose members are remarkably diverse, ranging from major pathogens of humans and animals to symbionts of ubiquitous protozoa. While their infective developmental stage, the elementary body (EB), has long been accepted to be completely metabolically inert, it has recently been shown to sustain some activities, including uptake of amino acids and protein biosynthesis. In the current study, we performed an in-depth characterization of the metabolic capabilities of EBs of the amoeba symbiont Protochlamydia amoebophila. A combined metabolomics approach, including fluorescence microscopy-based assays, isotope-ratio mass spectrometry (IRMS), ion cyclotron resonance Fourier transform mass spectrometry (ICR/FT-MS), and ultra-performance liquid chromatography mass spectrometry (UPLC-MS) was conducted, with a particular focus on the central carbon metabolism. In addition, the effect of nutrient deprivation on chlamydial infectivity was analyzed. Our investigations revealed that host-free P. amoebophila EBs maintain respiratory activity and metabolize D-glucose, including substrate uptake as well as host-free synthesis of labeled metabolites and release of labeled CO2 from 13C-labeled D-glucose. The pentose phosphate pathway was identified as major route of D-glucose catabolism and host-independent activity of the tricarboxylic acid (TCA) cycle was observed. Our data strongly suggest anabolic reactions in P. amoebophila EBs and demonstrate that under the applied conditions D-glucose availability is essential to sustain metabolic activity. Replacement of this substrate by L-glucose, a non-metabolizable sugar, led to a rapid decline in the number of infectious particles. Likewise, infectivity of Chlamydia trachomatis, a major human pathogen, also declined more rapidly in the absence of nutrients. Collectively, these findings demonstrate that D-glucose is utilized by P. amoebophila EBs and provide

Regulation of microtubule nucleation mediated by gamma-tubulin complexes

Czech Academy of Sciences Publication Activity Database

Sulimenko, Vadym; Hájková, Zuzana; Klebanovych, Anastasiya; Dráber, Pavel

2017-01-01

Roč. 254, č. 3 (2017), s. 1187-1199 ISSN 0033-183X R&D Projects: GA MŠk(CZ) LD13015 Institutional support: RVO:68378050 Keywords : mitotic spindle formation * ring complex * fission yeast * organizing centers * protein complex * golgi-complex * cell-cycle * pole body * augmin * centrosome * Centrosomes * Microtubule nucleation * Microtubule-organizing centers * Non-centrosomal nucleation sites * Spindle pole bodies * gamma-Tubulin complexes Subject RIV: EB - Genetics ; Molecular Biology OBOR OECD: Cell biology Impact factor: 2.870, year: 2016

Origin of allochthonous limestone bodies of the miocene Megami formation, Kakegawa district, Shizuoka prefecture. Shizuokaken Kakegawa chiiki no chushinto megamiso ni fukumareru ichisei sekkaigan gantai no kigen

Energy Technology Data Exchange (ETDEWEB)

Nakamori, T; Iryu, Y; Mori, K [Tohoku Univ., Sendai (Japan). Faculty of Science; Sasazawa, K [The Yomiuri Shimbun, Sendai (Japan). Tohoku General Bureau

1991-12-15

The Tertiary limestone bodies represented by Megami Hill and Ogami Hill are distributed in the Kakegawa district in the central portion of Shizuoka Prefecture, these limestone bodies are those originated from coral reefs and are contained in the Megami formation composed of sandstone, mudstone and tuff. However, concerning the limestone bodies of the Megami formation, there are, inter alia, the opinion that they are coral reef sediments on the spot and the opinion that they are foreign rocks, but neither has any firm concrete supporting evidence. In this paper, the sedimentation ages and the sedimentary locations of limestone and sandstone {center dot} mudstone composing the Megami formation were classified and the process, through which limestone was transformed up to its state now observed, was studied. The above study was done by a detailed survey of local rock facies, comparison of age of each rock facies through detection of reference fossils and other measures. A part of the conclusion is shown below: The limestone bodies of the Megami formation is discontinuous with the surrounding sandstone {center dot} mudstone and their strike dip is not harmonious. These limestone bodies are allochthonous rock blocks which collapsed after their sedimentation and mixed with the deep sea sediments (sandstone and mudstone). 37 refs., 4 figs., 4 tabs.

Extractable proteins from electron beam (EB) irradiated natural rubber (NR) latex

International Nuclear Information System (INIS)

Feroza Akhtar; Fumio Yoshii; Keizo Makuuchi

1996-01-01

The protein assay of natural rubber latex (NRL) vulcanized by low energy electron beam (EB, 300 keV, 30 mA) has been carried out using Bicinchoninic acid (BCA) reagent. Extractable protein in irradiated latex film was determined by measuring the absorption of colored solution at 562 nm using UV spectrometer. The effect of various radiation doses on the extractable protein content of NRL was investigated. It was ,found that the quantities of extractable protein increases with radiation dose. When compared with ,gamma-ray irradiated samples the same trend was observed. Electron beam irradiated latex films are leached in 1% (ammonia water for various lengths of time. From the results it was established that within 2 hours of leaching in ammonia water most of the extractable protein (96%) were removed from rubber film

Investigating the Potential Barrier Function of Nanostructured Materials Formed in Engineered Barrier Systems (EBS) Designed for Nuclear Waste Isolation.

Science.gov (United States)

Cuevas, Jaime; Ruiz, Ana Isabel; Fernández, Raúl

2018-02-21

Clay and cement are known nano-colloids originating from natural processes or traditional materials technology. Currently, they are used together as part of the engineered barrier system (EBS) to isolate high-level nuclear waste (HLW) metallic containers in deep geological repositories (DGR). The EBS should prevent radionuclide (RN) migration into the biosphere until the canisters fail, which is not expected for approximately 10 3  years. The interactions of cementitious materials with bentonite swelling clay have been the scope of our research team at the Autonomous University of Madrid (UAM) with participation in several European Union (EU) projects from 1998 up to now. Here, we describe the mineral and chemical nature and microstructure of the alteration rim generated by the contact between concrete and bentonite. Its ability to buffer the surrounding chemical environment may have potential for further protection against RN migration. © 2018 The Chemical Society of Japan & Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

In vitro differentiation of mouse embryonic stem (mES) cells using the hanging drop method.

Science.gov (United States)

Wang, Xiang; Yang, Phillip

2008-07-23

Stem cells have the remarkable potential to develop into many different cell types. When a stem cell divides, each new cell has the potential to either remain a stem cell or become another type of cell with a more specialized function, This promising of science is leading scientists to investigate the possibility of cell-based therapies to treat disease. When culture in suspension without antidifferentiation factors, embryonic stem cells spontaneously differentiate and form three-dimensional multicellular aggregates. These cell aggregates are called embryoid bodies(EB). Hanging drop culture is a widely used EB formation induction method. The rounded bottom of hanging drop allows the aggregation of ES cells which can provide mES cells a good environment for forming EBs. The number of ES cells aggregatied in a hanging drop can be controlled by varying the number of cells in the initial cell suspension to be hung as a drop from the lid of Petri dish. Using this method we can reproducibly form homogeneous EBs from a predetermined number of ES cells.

Apparatus for use in predicting hydrocarbon potential of an earth formation underlying a body of water

International Nuclear Information System (INIS)

Demaison, G.J.; Kaplan, I.R.

1984-01-01

In a relatively quick, convenient and highly accurate technique for the determination of a carbonaceous gas, normally methane, contained in water samples collected at depth from a body of water overlying an earth formation to predict the hydrocarbon-containing potential of the earth formation, carbonaceous gaseous constituents liberated from the water are carried via an air stream to flow into and through an isotope trapping network where collection in microlitre amounts occurs. The isotope capture apparatus comprises a box-like structure formed from a series of panel members, front panel member intersecting the bottom panel member near the centre of the latter and carrying interconnected gas trapping and stripping sections, the structure also comprising a detachable lid connectable by means, for protection of sections. (author)

Almahata Sitta MS-MU-011 and MS-MU-012: Formation Conditions of Two Unusual Rocks From the Ureilite Parent Body

Science.gov (United States)

Mikouchi, T.; Takenouchi, A.; Zolensky, M. E.; Hoffmann, V. H.

2018-01-01

Almahata Sitta meteorites are unique polymict breccia, comprising of many different meteorite groups as individual fragments dominated by ureilite lithologies and are considered to be recovered fragments of the asteroid 2008TC3. Recently, two unusual Almahata Sitta samples (MS-MU-011 and MS-MU-012) have been reported that show close petrogenetic relationships to ureilites. MS-MU-011 is a trachyandesite mainly composed of feldspar (plagioclase and anorthoclase) and pyroxene (pigeonite and augite) having ureilitic oxygen isotopic ratios. MS-MU-012 is the first ureilite example (unbrecciated) containing primary plagioclase crystals. The findings of these two rock types are important to better understand formation conditions of ureilites and the evolution of their parent body(s). In this abstract we discuss formation conditions of these ureilite-related rocks using redox state estimate by Fe valence states of plagioclase and olivine cooling rate calculations.

Consumed workers – disabled bodies. Historical knowledge formation after the cultural turn

Directory of Open Access Journals (Sweden)

Anne Klein

2016-12-01

Full Text Available Some recent OECD-studies tackle new psychosomatic symptoms in the context of work. So we find the paradoxical situation, that although the state of health and well-being in societies grows, statistics show growing rates of burn-out syndroms together with uneasiness, addiction and non-functioning. One in five workers suffer from a mental illness, such as depression or anxiety, and many more are struggling to cope. In a closer reading we can see, that the social-medical model still dominates this actual policy research, although the cultural model has gained growing recognition in the last fifteen years. But we find a double blank spot with relevance for historical knowledge formation: On the one side, studies on work that use the tool set of cultural studies can rarely be found. On the other side, disability studies that work with the cultural model are rarely tackling the working subject. Starting from this analytical point, this contribution wants to stimulate historical knowledge formation on the working subject. The epistemic perspective of this study is coined by the cultural model of disability; the methodology is based on the visual, the spatial and the linguistic turn. In studying historical artefacts like film scenes or juridical definitions, we can come to a closer understanding of how we conceptualise human beings. The thesis is, that during the 20th-century the changing “microphysics of power” (Foucault produced new forms of subjectivation: Either, workers tried to assimilate to the “machine rhythms” or they uttered their needs in “embodied dissent”. There are multilayered facets in between. I want to develop the argumentation that the body/mind-centering seems to be at the heart of the postfordist transformation. The article concludes by underlining the possibility to read bodies as a source, an approach Bryan S. Turner has theorized in his article “Disability and the Sociology of the Body”.

Peeling skin in newborn with abdominal distension

OpenAIRE

Sujay Kumar Maitra; Nilay Kanti Das; Niharika Ranjan Lal

2016-01-01

Epidermolysis bullosa (EB) is a rare hereditary disorder characterized by the formation of blisters following minor trauma. It has been traditionally categorized by the level of basement membrane zone separation into EB simplex, junctional EB, and dystrophic EB. Recently, hemidesmosomal EB has been proposed as a fourth category, which includes EB with muscular dystrophy and EB with pyloric atresia (PA). Among the subtypes, EB with PA is a rare form of EB. We report here a neonate with EB-PA, ...

Skalní řícení na hradě Jestřebí a jeho příčiny

Czech Academy of Sciences Publication Activity Database

Adamovič, Jiří; Kaňková, H.

2010-01-01

Roč. 19, - (2010), s. 137-162 ISSN 1211-9172 R&D Projects: GA AV ČR IAA300130806 Institutional research plan: CEZ:AV0Z30130516 Keywords : rockfall * Bohemian Cretaceous Basin * sandstone * Jestřebí Castle (Czech Republic) Subject RIV: DB - Geology ; Mineralogy

Expression of the urease gene of Agaricus bisporus: a tool for studying fruit body formation and post-harvest development

NARCIS (Netherlands)

Wagemaker, M.J.M.; Eastwood, D.C.; Drift, van der C.; Jetten, M.S.M.; Burton, K.; Griensven, van L.J.L.D.; Camp, op den H.J.M.

2006-01-01

Fruit body initials of Agaricus bisporus contain high levels of urea, which decrease in the following developmental stages until stage 4 (harvest) when urea levels increase again. At storage, the high urea content may affect the quality of the mushroom, i.e. by the formation of ammonia from urea

Evaluation of Factors Affecting Polyhydroxyalkanoates Production by Comamonas sp. EB172 Using Central Composite Design

Directory of Open Access Journals (Sweden)

Noor Azman Mohd Johar

2012-09-01

Full Text Available Aims: Statistical approach, central composite design (CCD was used to investigate the complex interaction among temperature (25-37 °C, initial medium pH (5-9, inoculum size (4-10 % (v/v, concentration of (NH42SO4 (0-1 g/L and concentration of mixed organic acids (5-10 g/L in the production of polyhydroxyalkanoates by Comamonas sp. EB172.Methodology and Results: Mixed organic acids derived from anaerobically treated palm oil mill effluent (POME containing acetic:propionic:butyric (ratio of 3:1:1 were used as carbon source in the batch culture of Comamonas sp. EB172 to produce polyhydoxyalkanoates (PHAs. The analysis of variance (ANOVA showed that all five factors were significantly important in the batch fermentation by shake flask with a P value of less than 0.001. The optimal temperature, initial medium pH, inoculum size, concentration of (NH42SO4 and concentration of mixed organic acids were 30 °C, 7.04, 4.0 % (v/v, 0.01 g/L and 5.05 g/L respectively.Conclusion, significance and impact of study: Optimization of the production medium containing mixed organic acids has improved the PHA production for more than 2 folds. Under optimal condition in the shake flask fermentation, the predicted growth is 2.98 g/L of dry cell weight (DCW with 47.07 wt % of PHA content. The highest yield of PHA was 0.28 g of PHA per g mixed organic acids.

Peeling skin in newborn with abdominal distension

Directory of Open Access Journals (Sweden)

Sujay Kumar Maitra

2016-01-01

Full Text Available Epidermolysis bullosa (EB is a rare hereditary disorder characterized by the formation of blisters following minor trauma. It has been traditionally categorized by the level of basement membrane zone separation into EB simplex, junctional EB, and dystrophic EB. Recently, hemidesmosomal EB has been proposed as a fourth category, which includes EB with muscular dystrophy and EB with pyloric atresia (PA. Among the subtypes, EB with PA is a rare form of EB. We report here a neonate with EB-PA, who, unfortunately, died on the 2nd day of life.

Single-photon sensitive fast ebCMOS camera system for multiple-target tracking of single fluorophores: application to nano-biophotonics

Science.gov (United States)

Cajgfinger, Thomas; Chabanat, Eric; Dominjon, Agnes; Doan, Quang T.; Guerin, Cyrille; Houles, Julien; Barbier, Remi

2011-03-01

Nano-biophotonics applications will benefit from new fluorescent microscopy methods based essentially on super-resolution techniques (beyond the diffraction limit) on large biological structures (membranes) with fast frame rate (1000 Hz). This trend tends to push the photon detectors to the single-photon counting regime and the camera acquisition system to real time dynamic multiple-target tracing. The LUSIPHER prototype presented in this paper aims to give a different approach than those of Electron Multiplied CCD (EMCCD) technology and try to answer to the stringent demands of the new nano-biophotonics imaging techniques. The electron bombarded CMOS (ebCMOS) device has the potential to respond to this challenge, thanks to the linear gain of the accelerating high voltage of the photo-cathode, to the possible ultra fast frame rate of CMOS sensors and to the single-photon sensitivity. We produced a camera system based on a 640 kPixels ebCMOS with its acquisition system. The proof of concept for single-photon based tracking for multiple single-emitters is the main result of this paper.

N-body simulations of terrestrial planet formation under the influence of a hot Jupiter

International Nuclear Information System (INIS)

Ogihara, Masahiro; Kobayashi, Hiroshi; Inutsuka, Shu-ichiro

2014-01-01

We investigate the formation of multiple-planet systems in the presence of a hot Jupiter (HJ) using extended N-body simulations that are performed simultaneously with semianalytic calculations. Our primary aims are to describe the planet formation process starting from planetesimals using high-resolution simulations, and to examine the dependences of the architecture of planetary systems on input parameters (e.g., disk mass, disk viscosity). We observe that protoplanets that arise from oligarchic growth and undergo type I migration stop migrating when they join a chain of resonant planets outside the orbit of an HJ. The formation of a resonant chain is almost independent of our model parameters, and is thus a robust process. At the end of our simulations, several terrestrial planets remain at around 0.1 AU. The formed planets are not equal mass; the largest planet constitutes more than 50% of the total mass in the close-in region, which is also less dependent on parameters. In the previous work of this paper, we have found a new physical mechanism of induced migration of the HJ, which is called a crowding-out. If the HJ opens up a wide gap in the disk (e.g., owing to low disk viscosity), crowding-out becomes less efficient and the HJ remains. We also discuss angular momentum transfer between the planets and disk.

Cdc42 is crucial for the establishment of epithelial polarity during early mammalian development

DEFF Research Database (Denmark)

Wu, Xunwei; Li, Shaohua; Chrostek-Grashoff, Anna

2007-01-01

To study the role of Cdc42 in the establishment of epithelial polarity during mammalian development, we generated murine Cdc42-null embryonic stem cells and analyzed peri-implantation development using embryoid bodies (EBs). Mutant EBs developed endoderm and underlying basement membrane, but exhi......To study the role of Cdc42 in the establishment of epithelial polarity during mammalian development, we generated murine Cdc42-null embryonic stem cells and analyzed peri-implantation development using embryoid bodies (EBs). Mutant EBs developed endoderm and underlying basement membrane...

Anisotropic TGO rumpling in EB-PVD thermal barrier coatings under in-phase thermomechanical loading

Energy Technology Data Exchange (ETDEWEB)

Balint, D.S., E-mail: d.balint@imperial.ac.uk [Department of Mechanical Engineering, Imperial College London, London SW7 2AZ (United Kingdom); Kim, S.-S.; Liu Yufu; Kitazawa, R.; Kagawa, Y. [Research Center for Advanced Science and Technology, University of Tokyo, 4-6-1 Komaba, Meguro-ku, Tokyo 153-8409 (Japan); Evans, A.G. [College of Engineering, University of California, Santa Barbara, CA 93106 (United States)

2011-04-15

An electron beam physical vapor deposited (EB-PVD) Y{sub 2}O{sub 3}-ZrO{sub 2} thermal barrier system has been tested under in-phase thermomechanical fatigue (TMF) conditions with thermal gradient in the through-thickness direction. Undulations in the thermally grown oxide (TGO) were observed to have clear anisotropic behavior with respect to the directions parallel and perpendicular to the loading axis. It was found that undulation wavelengths were nearly the same in both directions but the amplitude in the perpendicular direction was much larger than in the parallel direction. A recent model of TGO rumpling was adapted and used to analyze and explain the origins of the observed rumpling behavior under TMF conditions. Methods for deducing variation in the coefficient of thermal expansion with temperature and in the creep properties of the substrate from the experimental strain data are also presented in the course of the derivations. Model results show that tensile stress applied in the loading direction can overcome the compression occurring from lateral expansion during oxide formation, causing undulations to flatten; undulations perpendicular to the loading axis are unaffected. However, ratcheting in the strain cycle experienced by the substrate, which occurs naturally by substrate creep, is necessary for anisotropic rumpling under cyclic stress conditions. Model predictions for constant applied stress are also presented, demonstrating a reversal in the direction of undulation alignment under compression. A threshold stress is identified, in both tension and compression, sufficient to produce appreciable anisotropic rumpling. The model predictions provide a clear mechanism for the anisotropy and further evidence that the lateral expansion strain in the oxide is the driving force for oxide rumpling.

Anisotropic TGO rumpling in EB-PVD thermal barrier coatings under in-phase thermomechanical loading

International Nuclear Information System (INIS)

Balint, D.S.; Kim, S.-S.; Liu Yufu; Kitazawa, R.; Kagawa, Y.; Evans, A.G.

2011-01-01

An electron beam physical vapor deposited (EB-PVD) Y 2 O 3 -ZrO 2 thermal barrier system has been tested under in-phase thermomechanical fatigue (TMF) conditions with thermal gradient in the through-thickness direction. Undulations in the thermally grown oxide (TGO) were observed to have clear anisotropic behavior with respect to the directions parallel and perpendicular to the loading axis. It was found that undulation wavelengths were nearly the same in both directions but the amplitude in the perpendicular direction was much larger than in the parallel direction. A recent model of TGO rumpling was adapted and used to analyze and explain the origins of the observed rumpling behavior under TMF conditions. Methods for deducing variation in the coefficient of thermal expansion with temperature and in the creep properties of the substrate from the experimental strain data are also presented in the course of the derivations. Model results show that tensile stress applied in the loading direction can overcome the compression occurring from lateral expansion during oxide formation, causing undulations to flatten; undulations perpendicular to the loading axis are unaffected. However, ratcheting in the strain cycle experienced by the substrate, which occurs naturally by substrate creep, is necessary for anisotropic rumpling under cyclic stress conditions. Model predictions for constant applied stress are also presented, demonstrating a reversal in the direction of undulation alignment under compression. A threshold stress is identified, in both tension and compression, sufficient to produce appreciable anisotropic rumpling. The model predictions provide a clear mechanism for the anisotropy and further evidence that the lateral expansion strain in the oxide is the driving force for oxide rumpling.

Structural Properties of EB-Welded AlSi10Mg Thin-Walled Pressure Vessels Produced by AM-SLM Technology

Science.gov (United States)

Nahmany, Moshe; Stern, Adin; Aghion, Eli; Frage, Nachum

2017-10-01

Additive manufacturing of metals by selective laser melting (AM-SLM) is hampered by significant limitations in product size due to the limited dimensions of printing trays. Electron beam welding (EBW) is a well-established process that results in relatively minor metallurgical modifications in workpieces due to the ability of EBW to pass high-density energy to the related substance. The present study aims to evaluate structural properties of EB-welded AlSi10Mg thin-walled pressure vessels produced from components prepared by SLM technology. Following the EB welding process, leak and burst tests were conducted, as was fractography analysis. The welded vessels showed an acceptable holding pressure of 30 MPa, with a reasonable residual deformation up to 2.3% and a leak rate better than 1 × 10-8 std-cc s-1 helium. The failures that occurred under longitudinal stresses reflected the presence of two weak locations in the vessels, i.e., the welded joint region and the transition zone between the vessel base and wall. Fractographic analysis of the fracture surfaces of broken vessels displayed the ductile mode of the rupture, with dimples of various sizes, depending on the failure location.

Limits to prediction of energy balance from milk composition measures at individual cow level

DEFF Research Database (Denmark)

Løvendahl, P; Ridder, C; Friggens, N C

2010-01-01

at each milking. Three breeds (Danish Red, Holstein-Friesian, and Jersey) of cows (299 cows, 623 lactations) in parities 1 to 4 were used. Milk data were smoothed using a rolling local regression. Energy balance based on milk composition was calculated using a partial least squares (PLS) model based......Frequently updated energy balance (EB) estimates for individual cows are especially useful for dairy herd management, and individual-level estimates form the basis for group-level EB estimates. The accuracy of EB estimates determines the value of this information for management decision support....... This study aimed to assess EB accuracy through ANOVA components and by comparing EB estimates based either on milk composition (EBalMilk) or on body condition score (BCS) and body weight (BW) (EBalBody). Energy balance based on milk composition was evaluated using data in which milk composition was measured...

mGluR5 stimulating Homer–PIKE formation initiates icariin induced cardiomyogenesis of mouse embryonic stem cells by activating reactive oxygen species

Energy Technology Data Exchange (ETDEWEB)

Zhou, Limin; Huang, Yujie; Zhang, Yingying [Institute of Pharmacology, Toxicology and Biochemical Pharmaceutics, College of Pharmaceutical Sciences, Zhejiang University, No. 866, Yu Hang Tang Road, Hangzhou 310058 (China); Zhao, Qingwei [The First Affiliated Hospital, College of Medicine, Zhejiang University, No. 79, Qing Chun Road, Hangzhou 310003 (China); Zheng, Bei; Lou, Yijia [Institute of Pharmacology, Toxicology and Biochemical Pharmaceutics, College of Pharmaceutical Sciences, Zhejiang University, No. 866, Yu Hang Tang Road, Hangzhou 310058 (China); Zhu, Danyan, E-mail: zdyzxb@zju.edu.cn [Institute of Pharmacology, Toxicology and Biochemical Pharmaceutics, College of Pharmaceutical Sciences, Zhejiang University, No. 866, Yu Hang Tang Road, Hangzhou 310058 (China)

2013-06-10

Icariin (ICA) has been reported to facilitate cardiac differentiation of mouse embryonic stem (ES) cells; however, the mechanism by which ICA induced cardiomyogenesis has not been fully elucidated yet. Here, an underlying signaling network including metabotropic glutamate receptor 5 (mGluR5), Homer, phosphatidylinositol 3-Kinase Enhancer (PIKE), phosphatidylinositol 3-Kinase (PI3K), reactive oxygen species (ROS) and nuclear factor-kappaB (NF-κB) was investigated in ICA induced cardiomyogenesis. Our results showed that the co-expression of mGluR5 together with α-actinin or Troponin T in embryoid bodies (EBs) treated with ICA was elevated to 10.86% and 9.62%, compared with the case in the control (4.04% and 3.45%, respectively). Exposure of EBs to ICA for 2 h remarkably increased the dimeric form of mGluR5, which was inhibited by small interfering RNA targeting mGluR5 (si-mGluR5). Moreover, the extracellular glutamate concentration in ICA treatment medium was elevated to 28.9±3.5 μM. Furthermore, the activation of mGluR5 by ICA triggered the formation of Homer–PIKE complex and activated PI3K, stimulating ROS generation and NF-κB nuclear translocation. Knockdown of mGluR5 or inhibition of PI3K by LY294002 blocked ICA induced cardiomyogenesis via repressing mGluR5 pathway, reducing ROS and NF-κB activation. These results revealed that the inducible mechanisms of ICA were related to activate mGluR5 pathway. -- Highlights: • ICA increased mGluR5 expression in cardiac differentiation of ES cells. • ICA enhanced the glutamate level and the receptor mGluR5 dimerization, stimulating the formation of Homer–PIKE complex. • Knockdown of mGluR5 or inhibition of PI3K by LY294002 inhibited ICA induced ROS generation and NF-κB nuclear translocation.

Mechanical properties of EB-PVD ZrO{sub 2} thermal barrier coatings; Mechanische Eigenschaften von EB-PVD ZrO{sub 2} Waermedaemmschichten

Energy Technology Data Exchange (ETDEWEB)

Held, Carolin

2014-08-29

In this work, the elastic properties of thermal barrier coatings which were produced by electron-beam enhanced physical vapour deposition were investigated, as well as the dependency of the properties on the sample microstructure, the thermal treatment and the test method. For this purpose, not only commercial coatings were characterized, but also special sample material was used which consists of a 1 mm thick layer of EB-PVD TBC. This material was isothermally heat treated for different times at 950 C, 1100 C and 1200 C and then tested in a specially developed miniaturized bend test and by dynamic mechanical analysis. The sample material was tested by nanoindentation in order to measure the Young's modulus on a local scale, and the porosity of the samples was determined by microstructure analysis and porosimetry. The decrease of porosity could be connected with sintering and subsequent stiffening of the material. The test results are dependent on the tested volume. A small test volume leads to larger measured Young's moduli, while a large test volume yields lower values. The test volume also has an influence on the increase of stiffness during thermal exposure. With a small tested volume, a quicker increase of the Young's modulus was registered, which could be associated to the sintering of local structures.

Long-term avoidance memory formation is associated with a transient increase in mushroom body synaptic complexes in leaf-cutting ants

Directory of Open Access Journals (Sweden)

Agustina eFalibene

2015-04-01

Full Text Available Long-term behavioral changes related to learning and experience have been shown to be associated with structural remodeling in the brain. Leaf-cutting ants learn to avoid previously preferred plants after they have proved harmful for their symbiotic fungus, a process that involves long-term olfactory memory. We studied the dynamics of brain microarchitectural changes after long-term olfactory memory formation following avoidance learning in Acromyrmex ambiguus. After performing experiments to control for possible neuronal changes related to age and body size, we quantified synaptic complexes (microglomeruli, MG in olfactory regions of the mushroom bodies (MB at different times after learning. Long-term avoidance memory formation was associated with a transient change in MG densities. Two days after learning, MG density was higher than before learning. At days 4 and 15 after learning — when ants still showed plant avoidance — MG densities had decreased to the initial state. The structural reorganization of MG triggered by long-term avoidance memory formation clearly differed from changes promoted by pure exposure to and collection of novel plants with distinct odors. Sensory exposure by the simultaneous collection of several, instead of one, non-harmful plant species resulted in a decrease in MG densities in the olfactory lip. We hypothesize that while sensory exposure leads to MG pruning in the MB olfactory lip, the formation of long-term avoidance memory involves an initial growth of new MG followed by subsequent pruning.

Long-term avoidance memory formation is associated with a transient increase in mushroom body synaptic complexes in leaf-cutting ants.

Science.gov (United States)

Falibene, Agustina; Roces, Flavio; Rössler, Wolfgang

2015-01-01

Long-term behavioral changes related to learning and experience have been shown to be associated with structural remodeling in the brain. Leaf-cutting ants learn to avoid previously preferred plants after they have proved harmful for their symbiotic fungus, a process that involves long-term olfactory memory. We studied the dynamics of brain microarchitectural changes after long-term olfactory memory formation following avoidance learning in Acromyrmex ambiguus. After performing experiments to control for possible neuronal changes related to age and body size, we quantified synaptic complexes (microglomeruli, MG) in olfactory regions of the mushroom bodies (MBs) at different times after learning. Long-term avoidance memory formation was associated with a transient change in MG densities. Two days after learning, MG density was higher than before learning. At days 4 and 15 after learning-when ants still showed plant avoidance-MG densities had decreased to the initial state. The structural reorganization of MG triggered by long-term avoidance memory formation clearly differed from changes promoted by pure exposure to and collection of novel plants with distinct odors. Sensory exposure by the simultaneous collection of several, instead of one, non-harmful plant species resulted in a decrease in MG densities in the olfactory lip. We hypothesize that while sensory exposure leads to MG pruning in the MB olfactory lip, the formation of long-term avoidance memory involves an initial growth of new MG followed by subsequent pruning.

Correlation between volume and morphological changes in the hippocampal formation in Alzheimer's disease: rounding of the outline of the hippocampal body on coronal MR images

International Nuclear Information System (INIS)

Adachi, Michito; Sato, Takamichi; Kawakatsu, Shinobu; Ohshima, Fumi

2012-01-01

The aim of this study was to investigate whether the outline of the hippocampal body becomes rounded on coronal magnetic resonance imaging (MRI) as the volume of the hippocampal formation decreases in Alzheimer's disease (AD). Institutional review board approval of the study protocol was obtained, and all subjects provided informed consent for the mini-mental state examination (MMSE) and MRI. The MRI and MMSE were prospectively performed in all 103 subjects (27 men and 76 women; mean age ± standard deviation, 77.7 ± 7.8 years) who had AD or were concerned about having of dementia and who consulted our institute over 1 year. The subjects included 14 non-dementia cases (MMSE score ≥ 28) and 89 AD cases (MMSE score ≤ 27). The total volume of the bilateral hippocampal formation (VHF) was assessed with a tracing method, and the ratio of the VHF to the intracranial volume (RVHF) and the rounding ratio (RR) of the hippocampal body (mean ratio of its short dimension to the long dimension in the bilateral hippocampal body) were calculated. Using Spearman's correlation coefficient, the correlations between RR and VHF and between RR and RVHF were assessed. Correlation coefficients between RR and VHF and between RR and RVHF were -0.419 (p < 0.01) and -0.418 (p < 0.01), respectively. There was a significant negative correlation between RR and the volume of the hippocampal formation. The outline of the body of the hippocampal formation becomes rounded on coronal images as its volume decreases in AD. (orig.)

Dissection of Molecular Mechanisms Regulating Protein Body Formation in Maize Endosperm - DE-FG03-95-ER20183

International Nuclear Information System (INIS)

Larkins, Brian A.

2003-01-01

Dissection of Molecular Mechanisms Regulating Protein Body Formation in Maize Endosperm - DE-FG03-95-ER20183 Final Technical Report and Patent Summary Dr. Brian A. Larkins, Department of Plant Sciences, University of Arizona, Tucson, AZ 85721 Endosperm texture is an important quality trait in maize, as it influences the shipping characteristics of the grain, its susceptibility to insects, the yield of grits from dry milling, energy costs during wet milling, and the baking and digestibility properties of the flour. There appears to be a causal relationship between kernel hardness and the formation of zein-containing protein bodies, as mutations affecting protein body number and structure are associated with a soft, starchy kernel. In this project we used a variety of approaches to better understand this relationship and investigate the molecular and biochemical changes associated with starchy endosperm mutants. We characterized the distribution of zein mRNAs on endosperm rough endoplasmic reticulum (RER) membranes and the interactions between zein proteins, as each of these could influence the structure of protein bodies. Based on in situ hybridization, mRNAs encoding the 22-kD alpha- and 27-kD gamma-zeins are randomly distributed on RER; hence, mRNA targeting does not appear to influence the formation of protein bodies. Investigation of the interactions between zein proteins (alpha, beta, gamma, delta) with the yeast two-hybrid system showed that interactions between the 19- and 22-alpha-zeins are relatively weak, although each of them interacted strongly with the 10-kD delta-zein. Strong interactions were detected between the alpha- and delta-zeins and the 16-kD gamma- and 15-kD beta-zeins; however, the 50-kD and 27-kD gamma-zeins did not interact detectably with the alpha- and delta-zein proteins. The NH2- and COOH-terminal domains of the 22-kD alpha-zein were found to interact most strongly with the 15-kD beta- and 16-kD gamma-zeins, suggesting the 16-kD and 15

Nové sídliště lidu kultury s vypíchanou keramikou v Rouchovanech na Třebíčsku

Czech Academy of Sciences Publication Activity Database

Holub, M.; Kaiser, L.; Kočár, Petr; Kočárová, R.; Vokáč, M.; Vokáčová, J.

2013-01-01

Roč. 2013, č. 6 (2013), s. 7-15 ISSN 1804-2953 Institutional support: RVO:67985912 Keywords : Rouchovany * Třebíč region * archaeology * archaeobotany * archaeozoology * Neolithic * Stroked Pottery Culture Subject RIV: AC - Archeology, Anthropology, Ethnology

Growth and fruit body formation of Pleurotus ostreatus on media supplemented with inorganic selenium

Directory of Open Access Journals (Sweden)

Savić Milena D.

2009-01-01

Full Text Available Selenium is a trace mineral chemically related to sulfur and tellurium. In the body selenium combines with protein molecules to form selenoproteins and it is distributed in low concentrations and unequally in air, soil and water all over the world. Edible mushrooms are known to be selenium accumulators. Since mushrooms contain relatively high protein levels, and they can accumulate large amounts of selenium, it is reasonable to expect that selenium could be incorporated into proteins. The growth of mycelia and fruit body formation of different medicinal mushroom strains of Pleurotus ostreatus (Hk-35 and P70 over the wide range of concentrations of inorganic form of selenium were examined. Mushrooms were cultivated on agar base media and on substrates based on sawdust. Vegetative growths of mycelium were measured as colony diameter in pure cultures supplemented with inorganic form of Se supplements, prepared as Na2SeO4 and Na2SeO3 in concentrations of: 1, 10, 25, 50, 75, 100 and 150 mg/l. Inorganic form of Se supplements, showed stimulation effects (in concentration of 1-50 mg/l and toxic effects in higher concentration. On the standard industrial sawdust based substrate, supplemented with 100 mg/kg Na2SeO4 and Na2SeO3, accumulation of Se in fruit bodies was determined by the method of flameless atomic absorption spectrophotometer. The readings were performed on Varian SpectrAA-10 spectrophotometer equipped with VGA-76. Se as Na2SeO4 and Na2SeO3 was effectively taken up from substrates and accumulated in fruit bodies. Mushrooms accumulated selenium between 120 and 250 mg/kg dry weight. In mushrooms cultivated without Se supplement, Se contents were only about 1 mg/kg and in substrate about 0.1 mg/kg.

Assessment of asbestos body formation by high resolution FEG-SEM after exposure of Sprague-Dawley rats to chrysotile, crocidolite, or erionite.

Science.gov (United States)

Gandolfi, Nicola Bursi; Gualtieri, Alessandro F; Pollastri, Simone; Tibaldi, Eva; Belpoggi, Fiorella

2016-04-05

This work presents a comparative FEG-SEM study of the morphological and chemical characteristics of both asbestos bodies and fibres found in the tissues of Sprague-Dawley rats subjected to intraperitoneal or intrapleural injection of UICC chrysotile, UICC crocidolite and erionite from Jersey, Nevada (USA), with monitoring up to 3 years after exposure. Due to unequal dosing based on number of fibres per mass for chrysotile with respect to crocidolite and erionite, excessive fibre burden and fibre aggregation during injection that especially for chrysotile would likely not represent what humans would be exposed to, caution must be taken in extrapolating our results based on instillation in experimental animals to human inhalation. Notwithstanding, the results of this study may help to better understand the mechanism of formation of asbestos bodies. For chrysotile and crocidolite, asbestos bodies are systematically formed on long asbestos fibres. The number of coated fibres is only 3.3% in chrysotile inoculated tissues. In UICC crocidolite, Mg, Si, and Fe are associated with the fibres whereas Fe, P and Ca are associated with the coating. Even for crocidolite, most of the observed fibres are uncoated as coated fibres are about 5.7%. Asbestos bodies do not form on erionite fibres. The crystal habit, crystallinity and chemistry of all fibre species do not change with contact time, with the exception of chrysotile which shows signs of leaching of Mg. A model for the formation of asbestos bodies from mineral fibres is postulated. Because the three fibre species show limited signs of dissolution in the tissue, they cannot act as source of elements (primarily Fe, P and Ca) promoting nucleation and growth of asbestos bodies. Hence, the limited number of coated fibres should be due to the lack of nutrients or organic nature. Copyright © 2015 Elsevier B.V. All rights reserved.

An Amino Acid of Human Parainfluenza Virus Type 3 Nucleoprotein Is Critical for Template Function and Cytoplasmic Inclusion Body Formation

Science.gov (United States)

Zhang, Shengwei; Chen, Longyun; Zhang, Guangyuan; Yan, Qin; Yang, Xiaodan; Ding, Binbin; Tang, Qiaopeng; Sun, Shengjun; Hu, Zhulong

2013-01-01

The nucleoprotein (N) and phosphoprotein (P) interaction of nonsegmented negative-strand RNA viruses is essential for viral replication; this includes N0-P (N0, free of RNA) interaction and the interaction of N-RNA with P. The precise site(s) within N that mediates the N-P interaction and the detailed regulating mechanism, however, are less clear. Using a human parainfluenza virus type 3 (HPIV3) minigenome assay, we found that an N mutant (NL478A) did not support reporter gene expression. Using in vivo and in vitro coimmunoprecipitation, we found that NL478A maintains the ability to form NL478A0-P, to self-assemble, and to form NL478A-RNA but that NL478A-RNA does not interact with P. Using an immunofluorescence assay, we found that N-P interaction provides the minimal requirement for the formation of cytoplasmic inclusion bodies, which contain viral RNA, N, P, and polymerase in HPIV3-infected cells. NL478A was unable to form inclusion bodies when coexpressed with P, but the presence of N rescued the ability of NL478A to form inclusion bodies and the transcriptional function of NL478A, thereby suggesting that hetero-oligomers formed by N and NL478A are functional and competent to form inclusion bodies. Furthermore, we found that NL478A is also defective in virus growth. To our knowledge, we are the first to use a paramyxovirus to identify a precise amino acid within N that is critical for N-RNA and P interaction but not for N0-P interaction for the formation of inclusion bodies, which appear to be bona fide sites of RNA synthesis. PMID:24027324

Isolation and differentiation of chondrocytic cells derived from human embryonic stem cells using dlk1/FA1 as a novel surface marker

DEFF Research Database (Denmark)

Harkness, Linda; Taipaleenmaki, Hanna; Mahmood, Amer

2009-01-01

of dlk1/FA1 as a novel surface marker for chondroprogenitor cells during hESC differentiation. We found that, Dlk1/FA1 is expressed specifically in cells undergoing transition from proliferating to prehypertrophic chondrocytes during endochondral ossification of the mouse limb. In hESC cells, dlk1/FA1...... was not expressed by undifferentiated hESC, but expressed during in vitro embryoid bodies (hEBs) formation upon down-regulation of undifferentiated markers e.g. Oct 3/4. Similarly, dlk1/FA1 was expressed in chondrocytic cells during in vivo teratoma formation. Interestingly, treatment of hEBs with Activin B......, a member of TGF-ss family, markedly increased Dlk1 expression in association with up-regulation of the mesoderm-specific markers (e.g. FOXF1, KDR and VE-cadherin) and SOX9. dlk1/FA1(+) cells isolated by fluorescence activated cell sorting (FACS) were capable of differentiating into chondrocytic cells when...

Effects of a whole body gamma irradiation on GABA repartition in infant rats cerebellum and hippocampal formation

International Nuclear Information System (INIS)

Menetrier, F.; Vernois, Y.; Court, L.

1992-01-01

'Full-Text:' Thirteen-day-old rats were exposed to a single dose of 4 or 0,5 Gy of gamma at a dose rate of 0,25 Gy/min and were killed about 5h after. Fixation was achieved in situ using glutaraldehyde. For GABA immunocytochemistry transversal sections were incubated with antiserum against GABA, then with PAP and revealed with diaminobenzidine. Proliferative layers are still observed in the infant rat cerebellum (external granular layer) and hippocampal formation (subgranular layer of the dentate gyrus). When irradiation occurs a high percent of these two layers cells are pycnotic. In the normal cerebellum, no immunostaining is observed in external granular layer cell bodies. The only labelled structures are few cytoplasmic expansions coming from subjacent layers. When irradiated, a strong GABA staining appears around pycnotic cells as a network with labelled meshes. GABA staining and pycnotic cells were more especially important when the irradiation increases. Further studies are needed to specify the nature of labelled meshes. In the normal hippocampal formation, subgranular cells are not GABA stained. Staining occurs in cells which are not granule cells. They are scattered throughout cell layers of the dentate gyrus with predominance in the hilus. After irradiation, GABA repartition is not modified. After a 4 Gy whole body gamma irradiation, the inhibitory GABA system is not injured. Other amino-acid neurotransmitters such as Glutamate could be modified. (author)

Mechanical properties of EB-PVD ZrO{sub 2} thermal barrier coatings; Mechanische Eigenschaften von EB-PVD ZrO{sub 2} Waermedaemmschichten

Energy Technology Data Exchange (ETDEWEB)

Held, Carolin

2014-08-29

In this work, the elastic properties of thermal barrier coatings which were produced by electron-beam enhanced physical vapour deposition were investigated, as well as the dependency of the properties on the sample microstructure, the thermal treatment and the test method. For this purpose, not only commercial coatings were characterized, but also special sample material was used which consists of a 1 mm thick layer of EB-PVD TBC. This material was isothermally heat treated for different times at 950 C, 1100 C and 1200 C and then tested in a specially developed miniaturized bend test and by dynamic mechanical analysis. The sample material was tested by nanoindentation in order to measure the Young's modulus on a local scale, and the porosity of the samples was determined by microstructure analysis and porosimetry. The decrease of porosity could be connected with sintering and subsequent stiffening of the material. The test results are dependent on the tested volume. A small test volume leads to larger measured Young's moduli, while a large test volume yields lower values. The test volume also has an influence on the increase of stiffness during thermal exposure. With a small tested volume, a quicker increase of the Young's modulus was registered, which could be associated to the sintering of local structures.

Enhancement of committed hematopoietic stem cell colony formation by nandrolone decanoate after sublethal whole body irradiation

Energy Technology Data Exchange (ETDEWEB)

Gallicchio, V.S.; Chen, M.G.; Watts, T.D.

1984-11-01

The ability of an anabolic steroid, nandrolone decanoate, to increase committed topoietic stem cell (CFU-gm, CFU-e, and BFU-e) colony formation after sublethal irradiation was evaluated. Immediately after receiving whole body irradiation and on the next two days, each mouse was injected intraperitoneally with nandrolone decanoate (1.25 mg) in propylene glycol. Irradiated control mice received only propylene glycol. Compared to controls, drug-treated mice showed marked peripheral blood leukocytosis and more stable packed red cell volume. Drug-treated mice also demonstrated increased erythropoiesis, as CFU-e/BFU-e concentrations from both marrow (9% to 581%) and spleen (15% to 797%) were elevated. Granulopoiesis was increased similarly, as CFU-gm concentrations from marrow (38% to 685%) and spleen (9% to 373%) were elevated. These results demonstrate that nandrolone decanoate enhances hematopoietic stem cell recovery after sublethal whole body irradiation. This suggests that following hematopoietic suppression, nandrolone decanoate may stimulate the recovery of hematopoiesis at the stem cell level and in peripheral blood.

Enhancement of committed hematopoietic stem cell colony formation by nandrolone decanoate after sublethal whole body irradiation

International Nuclear Information System (INIS)

Gallicchio, V.S.; Chen, M.G.; Watts, T.D.

1984-01-01

The ability of an anabolic steroid, nandrolone decanoate, to increase committed topoietic stem cell (CFU-gm, CFU-e, and BFU-e) colony formation after sublethal irradiation was evaluated. Immediately after receiving whole body irradiation and on the next two days, each mouse was injected intraperitoneally with nandrolone decanoate (1.25 mg) in propylene glycol. Irradiated control mice received only propylene glycol. Compared to controls, drug-treated mice showed marked peripheral blood leukocytosis and more stable packed red cell volume. Drug-treated mice also demonstrated increased erythropoiesis, as CFU-e/BFU-e concentrations from both marrow (9% to 581%) and spleen (15% to 797%) were elevated. Granulopoiesis was increased similarly, as CFU-gm concentrations from marrow (38% to 685%) and spleen (9% to 373%) were elevated. These results demonstrate that nandrolone decanoate enhances hematopoietic stem cell recovery after sublethal whole body irradiation. This suggests that following hematopoietic suppression, nandrolone decanoate may stimulate the recovery of hematopoiesis at the stem cell level and in peripheral blood

Comet formation

Science.gov (United States)

Blum, J.

2014-07-01

There has been vast progress in our understanding of planetesimal formation over the past decades, owing to a number of laboratory experiments as well as to refined models of dust and ice agglomeration in protoplanetary disks. Coagulation rapidly forms cm-sized ''pebbles'' by direct sticking in collisions at low velocities (Güttler et al. 2010; Zsom et al. 2010). For the further growth, two model approaches are currently being discussed: (1) Local concentration of pebbles in nebular instabilities until gravitational instability occurs (Johansen et al. 2007). (2) A competition between fragmentation and mass transfer in collisions among the dusty bodies, in which a few ''lucky winners'' make it to planetesimal sizes (Windmark et al. 2012a,b; Garaud et al. 2013). Predictions of the physical properties of the resulting bodies in both models allow a distinction of the two formation scenarios of planetesimals. In particular, the tensile strength (i.e, the inner cohesion) of the planetesimals differ widely between the two models (Skorov & Blum 2012; Blum et al. 2014). While model (1) predicts tensile strengths on the order of ˜ 1 Pa, model (2) results in rather compactified dusty bodies with tensile strengths in the kPa regime. If comets are km-sized survivors of the planetesimal-formation era, they should in principle hold the secret of their formation process. Water ice is the prime volatile responsible for the activity of comets. Thermophysical models of the heat and mass transport close to the comet-nucleus surface predict water-ice sublimation temperatures that relate to maximum sublimation pressures well below the kPa regime predicted for formation scenario (2). Model (1), however, is in agreement with the observed dust and gas activity of comets. Thus, a formation scenario for cometesimals involving gravitational instability is favored (Blum et al. 2014).

Characterization and evaluation of EB-PVD thermal barrier coatings by impedance spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Zhang Chunxia; Liu Fushun; Gong Shengkai; Xu Huibin [School of Materials Science and Engineering, Beihang Univ., Beijing, BJ (China)

2005-07-01

Two layer thermal barrier coatings (TBCs) were prepared by EB-PVD (electron beam-physical vapor deposition) at different substrate temperatures in the range of 823 to 1123 K, and their microstructure was investigated with SEM and AC impedance as a function of substrate temperature and thermal cycling time. YSZ layer of all TBCs samples is in column structure, but the grain size and growth orientation are different with substrate. In this research, impedance spectra (IS) was measured as a function of thermal cycling between 1323 K and 298 K for these thermal barrier coatings. Grain boundary and bulk can be distinguished from analysis of AC impedance spectroa to provide information about the relation between microstructure and electric properties. The change in IS until failure was found to be related with the thickness, microcracks and macrocracks of TGO and the change in the interfacial of TGO/YSZ. (orig.)

Proceedings of the FNCA 2005 workshop on application of electron accelerator. EB treatment of wastewater

International Nuclear Information System (INIS)

Yoshii, Fumio; Kume, Tamikazu

2006-08-01

'Forum for Nuclear Cooperation in Asia (FNCA) Workshop on Application of Electron Accelerator' was sponsored by the Ministry of Education, Culture, Sports, Science and Technology (MEXT), Japan. The 2005 workshop was jointly organized by the Ministry of Science and Technology (MOST), Korea, Korea Atomic Energy Research Institute and Japan Atomic Energy Agency (JAEA). It was held at the International Nuclear Technology and Education Center (INTEC/KAERI), Daejeon, Korea from 14 to 18 November 2005. The Workshop was attended by 32 experts on application of electron accelerator from each of the participating countries, i.e., China (1), Indonesia (1), Korea (18), Malaysia (2), Philippines (1), Thailand (1) and Vietnam (1), and 7 participants from Japan. On the first day, a National Executive Management Seminar on Application of Electron Accelerator was held and attended by 45 participants. Total of 20 papers including Seminar lectures, invited papers on wastewater treatment by electron beam, and country reports on EB irradiation system were presented. The major areas of interest of FNCA member states for cooperation were identified for application of low energy electron accelerator to liquids (natural polymer, wastewater), solids (hydrogel, thin film) and gases (flue gas). Based on the evaluation and proposal from the participating countries, discussions were carried out to re-formulate the work plan of the project on natural polymers and wastewater for three years until FY 2008. It was agreed the FNCA 2006 workshop on EB crosslinking of natural polymers would be held in Malaysia. All manuscripts submitted by every speaker were included in the proceedings. The 18 presented papers are indexed individually. (J.P.N.)

Proceedings of the FNCA 2004 workshop on application of electron accelerator. EB treatment of flue gases

International Nuclear Information System (INIS)

Yoshii, Fumio; Kume, Tamikazu

2005-06-01

'Forum for Nuclear Cooperation in Asia (FNCA) Workshop on Application of Electron Accelerator' was sponsored by the Ministry of Education, Culture, Sports, Science and Technology (MEXT). The 2004 workshop was jointly organized by China Atomic Energy Authority (CAEA), Institute of Modern Physics/Chinese Academy of Sciences(IMP-CAS) and Japan Atomic Energy Research Institute (JAERI). It was held at Prime Hotel, Beijing, China from 6 to 10 September 2004. The Workshop was attended by 28 experts on application of electron accelerator from each of the participating countries, i.e., China, Indonesia, Korea, Malaysia, The Philippines, Thailand and Vietnam, and 10 participants from Japan. On the first day, a National Executive Management Seminar on Application of Electron Accelerator was held and attended by 67 participants. Total of 20 papers including Seminar lectures, invited papers on flue gas treatment by electron beam, and country reports on EB irradiation system were presented. The major areas of interest of FNCA member states for cooperation were identified for application of low energy electron accelerator as liquid (natural polymer, wastewater), solid (hydrogel, thin film) and gases (flue gas). Based on the proposal from the participating countries, discussions were carried out to re-formulate the work plan of the project for three years until FY 2005. It was agreed the FNCA 2005 workshop on EB treatment of wastewater will be held in Korea. All manuscripts submitted by every speaker were included in the proceedings. The 20 of the presented papers are indexed individually. (J.P.N.)

Efficient differentiation of steroidogenic and germ-like cells from epigenetically-related iPSCs derived from ovarian granulosa cells.

Directory of Open Access Journals (Sweden)

Raymond Anchan

Full Text Available To explore restoration of ovarian function using epigenetically-related, induced pluripotent stem cells (iPSCs, we functionally evaluated the epigenetic memory of novel iPSC lines, derived from mouse and human ovarian granulosa cells (GCs using c-Myc, Klf4, Sox2 and Oct4 retroviral vectors. The stem cell identity of the mouse and human GC-derived iPSCs (mGriPSCs, hGriPSCs was verified by demonstrating embryonic stem cell (ESC antigen expression using immunocytochemistry and RT-PCR analysis, as well as formation of embryoid bodies (EBs and teratomas that are capable of differentiating into cells from all three germ layers. GriPSCs' gene expression profiles associate more closely with those of ESCs than of the originating GCs as demonstrated by genome-wide analysis of mRNA and microRNA. A comparative analysis of EBs generated from three different mouse cell lines (mGriPSCs; fibroblast-derived iPSC, mFiPSCs; G4 embryonic stem cells, G4 mESCs revealed that differentiated mGriPSC-EBs synthesize 10-fold more estradiol (E2 than either differentiated FiPSC- or mESC-EBs under identical culture conditions. By contrast, mESC-EBs primarily synthesize progesterone (P4 and FiPSC-EBs produce neither E2 nor P4. Differentiated mGriPSC-EBs also express ovarian markers (AMHR, FSHR, Cyp19a1, ER and Inha as well as markers of early gametogenesis (Mvh, Dazl, Gdf9, Boule and Zp1 more frequently than EBs of the other cell lines. These results provide evidence of preferential homotypic differentiation of mGriPSCs into ovarian cell types. Collectively, our data support the hypothesis that generating iPSCs from the desired tissue type may prove advantageous due to the iPSCs' epigenetic memory.

miR-200c and GATA binding protein 4 regulate human embryonic stem cell renewal and differentiation

Directory of Open Access Journals (Sweden)

Hsiao-Ning Huang

2014-03-01

Full Text Available Human embryonic stem cells (hESCs are functionally unique for their self-renewal ability and pluripotency, but the molecular mechanisms giving rise to these properties are not fully understood. hESCs can differentiate into embryoid bodies (EBs containing ectoderm, mesoderm, and endoderm. In the miR-200 family, miR-200c was especially enriched in undifferentiated hESCs and significantly downregulated in EBs. The knockdown of the miR-200c in hESCs downregulated Nanog expression, upregulated GATA binding protein 4 (GATA4 expression, and induced hESC apoptosis. The knockdown of GATA4 rescued hESC apoptosis induced by downregulation of miR-200c. miR-200c directly targeted the 3′-untranslated region of GATA4. Interestingly, the downregulation of GATA4 significantly inhibited EB formation in hESCs. Overexpression of miR-200c inhibited EB formation and repressed the expression of ectoderm, endoderm, and mesoderm markers, which could partially be rescued by ectopic expression of GATA4. Fibroblast growth factor (FGF and activin A/nodal can sustain hESC renewal in the absence of feeder layer. Inhibition of transforming growth factor-β (TGF-β/activin A/nodal signaling by SB431542 treatment downregulated the expression of miR-200c. Overexpression of miR-200c partially rescued the expression of Nanog/phospho-Smad2 that was downregulated by SB431542 treatment. Our observations have uncovered novel functions of miR-200c and GATA4 in regulating hESC renewal and differentiation.

Improved mechanical properties of Ni-rich Ni3Al coatings produced by EB-PVD for repairing single crystal blades

Institute of Scientific and Technical Information of China (English)

Jing-Yong Sun; Yan-Ling Pei; Shu-Suo Li; Hu Zhang; Sheng-Kai Gong

2017-01-01

Active control of turbine blade tip clearance for aircraft engine continues to be a concern in engine operation,because turbine blades are subjected to wear and therefore cause an increasing tip clearance between the rotating blades and the shroud and also reduce the engine efficiency.In this work,a Ni-rich Ni3Al coating with γ'/γtwo-phase microstructure was deposited by electron beam physical vapor deposition (EB-PVD),which worked as repairing the worn blade tips of single crystal blades.Nb molten pool was used to increase the molten pool temperature and thus to enhance the deposition rate.The microstructures and mechanical properties can be modified by the deposition temperatures and the following heat treatments.All coatings consist of γ'and γ phases.At deposition temperature of 600 ℃,a dense microstructure can be achieved to produce a coating with grain size of ～ 1 μm and microhardness of ～HV 477.After being heated for 4 h at a temperature of 1,100 ℃,the coatings have a more uniform microstructure,and microhardness maintains at a high level of ～ HV 292.Effect of Hf and Zr on EB-PVD Ni3Al repair coating will be further investigated.

[Heinike Heinsoo. Mā ja pūd lēväd, meid eb lē : the subject and the predicate in Votic] / Johanna Laakso

Index Scriptorium Estoniae

Laakso, Johanna, 1962-

2012-01-01

Arvustus: Heinike Heinsoo. Mā ja pūd lēväd, meid eb lē : the subject and the predicate in Votic. Tallinn : Teaduste Akadeemia Kirjastus, 2010. (Linguistica Uralica. Supplementary series ; vol. 4)

Differences in body composition measured using the bioelectrical impedance analysis with steel and gel electrodes – on an example of professional fencers

Directory of Open Access Journals (Sweden)

Olga Mizera

2018-03-01

Full Text Available Introduction: Regular assessment of body composition in athletes is a key element of their nutritional status and general condition monitoring. Purpose: Analysis of differences in the impedance (I and body composition measurements performed by the use of analyzers with a constant current frequency of 50 kHz with steel and gel electrodes. Material and methods: Analysis were performed in experienced fencers by the use of analyzers: Tanita BC418MA (aT with steel electrodes (eT and Akern BIA101ASE (aA with gel electrodes (eA, eL, eT. During the first stage of the study in 48 athletes I, fat mass (FM and fat free mass (FFM were measured using aA with eB in a supine position and after 3 min using aT with eT in a standing position. Then 10 fencers were randomly selected. For them measurements were performed after 10, 13 and 16 min in a supine position using eA, eL, eB and then after 3 min in a standing one using eT. Intrinsic impedance of the 3 types of gel electrodes (eA, eL, eB were measured using aA. Results: The first stage. Differences in I, FM and FFM between eT and aA were observed (women: 101.4±52.2Ω, 1.2±2.1kg, -1.2±2.1kg, men: 98.8±27.5Ω, 1.1±1.5kg, -1.1±1.5kg, respectively. The second stage. In the subsequent measurements, differences in I were observed (women: eL-eA 3.8±1.8Ω, eB-eA 26.1±8.0Ω, eT-eA 154.4±40.6Ω;, men: of -0.7±9.4Ω, 11.1±9.2Ω, 107±36.3Ω, respectively. In both subgroups along with the increase in I, FM also increased, while  FFM decreased. Intrinsic impedance of the applied gel electrodes was measured and the differences between the results were reported (eL-eA 41.1±22.0Ω, eB-eL 138.4±20.7Ω, eB-eA 179.5Ω. As the intrinsic impedance of gel electrodes increased, an increase in the whole body I was observed. Conclusion: It seems that the observed differences in the whole body impedance were not only a simple effect of changes in a body position but they might have also been related to the intrinsic

Full-scale demonstration of EBS construction technology II. Design, manufacturing and transportation of pre-fabricated EBS module (PEM)

International Nuclear Information System (INIS)

Asano, Hidekazu; Toguri, Satohito; Iwata, Yumiko; Kawakami, Susumu; Nagasawa, Yuji; Yoshida, Takeshi

2008-01-01

PEM was investigated as a full-scale demonstration for the design, manufacturing and construction by using simulated buffer material and overpack in consideration of horizontal emplacement. Also near full-scale tests were conducted to examine the applicability of air-bearing system which can be used to transport a heavy load at the drift tunnel as for PEM. With regard to PEM casing, design requirements were selected from the viewpoints of EBS performance and operation safety issues. The construction procedure was examined in consideration of the shapes of buffer material, which are previously positioned inside the casing. And design procedure of the casing was also examined and presented. A full-scale PEM casing as a longitudinally two-part divided cylinder type with connection flanges was manufactured by using carbon steel plate. The wall thickness of this non-leak tight type PEM casing was evaluated its mechanical integrity by 2-dimensional stress analysis in consideration of the emplacement condition on the drift tunnel basement. Mechanical integrity of a percolated type casing was also examined its mechanical integrity. Air-bearing unit, which originally apply to a flat/smooth surface, was modified to fit a curved surface of the drift tunnel. Two units were aligned with two parallel lines, which estimate to be able to lift 12 tons, about two-fifth of the total weight of full scale PEM. On the conducted transportation tests of the air-bearing units, considering the surface roughness of the drift tunnel, especially for its unevenness, capability and availability of the run-over such gaps were investigated. And effect of covering sheets which can improve the gapped surface into relatively smooth was also examined by using several candidate materials. Through these tests, combination of the covering sheets and the maximum available height difference were evaluated and identified. Also the maximum traction force to toe the loading was measured to design the air

Phase separation of a Lennard-Jones fluid interacting with a long, condensed polymer chain: implications for the nuclear body formation near chromosomes.

Science.gov (United States)

Oh, Inrok; Choi, Saehyun; Jung, YounJoon; Kim, Jun Soo

2015-08-28

Phase separation in a biological cell nucleus occurs in a heterogeneous environment filled with a high density of chromatins and thus it is inevitably influenced by interactions with chromatins. As a model system of nuclear body formation in a cell nucleus filled with chromatins, we simulate the phase separation of a low-density Lennard-Jones (LJ) fluid interacting with a long, condensed polymer chain. The influence of the density variation of LJ particles above and below the phase boundary and the role of attractive interactions between LJ particles and polymer segments are investigated at a fixed value of strong self-interaction between LJ particles. For a density of LJ particles above the phase boundary, phase separation occurs and a dense domain of LJ particles forms irrespective of interactions with the condensed polymer chain whereas its localization relative to the polymer chain is determined by the LJ-polymer attraction strength. Especially, in the case of moderately weak attractions, the domain forms separately from the polymer chain and subsequently associates with the polymer chain. When the density is below the phase boundary, however, the formation of a dense domain is possible only when the LJ-polymer attraction is strong enough, for which the domain grows in direct contact with the interacting polymer chain. In this work, different growth behaviors of LJ particles result from the differences in the density of LJ particles and in the LJ-polymer interaction, and this work suggests that the distinct formation of activity-dependent and activity-independent nuclear bodies (NBs) in a cell nucleus may originate from the differences in the concentrations of body-specific NB components and in their interaction with chromatins.

Lhx2 expression promotes self-renewal of a distinct multipotential hematopoietic progenitor cell in embryonic stem cell-derived embryoid bodies.

Directory of Open Access Journals (Sweden)

Lina Dahl

Full Text Available The molecular mechanisms regulating the expansion of the hematopoietic system including hematopoietic stem cells (HSCs in the fetal liver during embryonic development are largely unknown. The LIM-homeobox gene Lhx2 is a candidate regulator of fetal hematopoiesis since it is expressed in the fetal liver and Lhx2(-/- mice die in utero due to severe anemia. Moreover, expression of Lhx2 in embryonic stem (ES cell-derived embryoid bodies (EBs can lead to the generation of HSC-like cell lines. To further define the role of this transcription factor in hematopoietic regulation, we generated ES cell lines that enabled tet-inducible expression of Lhx2. Using this approach we observed that Lhx2 expression synergises with specific signalling pathways, resulting in increased frequency of colony forming cells in developing EB cells. The increase in growth factor-responsive progenitor cells directly correlates to the efficiency in generating HSC-like cell lines, suggesting that Lhx2 expression induce self-renewal of a distinct multipotential hematopoietic progenitor cell in EBs. Signalling via the c-kit tyrosine kinase receptor and the gp130 signal transducer by IL-6 is necessary and sufficient for the Lhx2 induced self-renewal. While inducing self-renewal of multipotential progenitor cells, expression of Lhx2 inhibited proliferation of primitive erythroid precursor cells and interfered with early ES cell commitment, indicating striking lineage specificity of this effect.

Dissection of Molecular Mechanisms Regulating Protein Body Formation in Maize Endosperm - DE-FG03-95-ER20183 B139

Energy Technology Data Exchange (ETDEWEB)

Brian A. Larkins

2003-03-21

Dissection of Molecular Mechanisms Regulating Protein Body Formation in Maize Endosperm - DE-FG03-95-ER20183 Final Technical Report and Patent Summary Dr. Brian A. Larkins, Department of Plant Sciences, University of Arizona, Tucson, AZ 85721 Endosperm texture is an important quality trait in maize, as it influences the shipping characteristics of the grain, its susceptibility to insects, the yield of grits from dry milling, energy costs during wet milling, and the baking and digestibility properties of the flour. There appears to be a causal relationship between kernel hardness and the formation of zein-containing protein bodies, as mutations affecting protein body number and structure are associated with a soft, starchy kernel. In this project we used a variety of approaches to better understand this relationship and investigate the molecular and biochemical changes associated with starchy endosperm mutants. We characterized the distribution of zein mRNAs on endosperm rough endoplasmic reticulum (RER) membranes and the interactions between zein proteins, as each of these could influence the structure of protein bodies. Based on in situ hybridization, mRNAs encoding the 22-kD alpha- and 27-kD gamma-zeins are randomly distributed on RER; hence, mRNA targeting does not appear to influence the formation of protein bodies. Investigation of the interactions between zein proteins (alpha, beta, gamma, delta) with the yeast two-hybrid system showed that interactions between the 19- and 22-alpha-zeins are relatively weak, although each of them interacted strongly with the 10-kD delta-zein. Strong interactions were detected between the alpha- and delta-zeins and the 16-kD gamma- and 15-kD beta-zeins; however, the 50-kD and 27-kD gamma-zeins did not interact detectably with the alpha- and delta-zein proteins. The NH2- and COOH-terminal domains of the 22-kD alpha-zein were found to interact most strongly with the 15-kD beta- and 16-kD gamma-zeins, suggesting the 16-kD and 15

Energy Balance over One Athletic Season.

Science.gov (United States)

Silva, Analiza M; Matias, Catarina N; Santos, Diana A; Thomas, Diana; Bosy-Westphal, Anja; Müller, Manfred J; Heymsfield, Steven B; Sardinha, Luís B

2017-08-01

Magnitude and variation in energy balance (EB) components over an athletic season are largely unknown. We investigated the longitudinal changes in EB over one season and explored the association between EB variation and change in the main fat-free mass (FFM) components in highly trained athletes. Eighty athletes (54 males; handball, volleyball, basketball, triathlete, and swimming) were evaluated from the beginning of the season to the main competition stage. Resting and total energy expenditure (REE and TEE, respectively) were assessed by indirect calorimetry and doubly labeled water, respectively. Physical activity energy expenditure was calculated as TEE - 0.1 TEE - REE. Fat mass (FM), FFM, and bone mineral were evaluated with dual-energy x-ray absorptiometry; changed body energy stores were calculated as 1.0(ΔFFM/Δtime) + 9.5(ΔFM/Δtime). Total-body water (TBW) and its compartments were assessed through dilution techniques, and total-body protein was calculated from a four-compartment model, with body volume assessed by air displacement plethysmography. Although a negative EB of -17.4 ± 72.7 kcal·d was observed (P sports and across sex groups resulting in a net weight increase (0.7 ± 2.3 kg) that is attributable to significant changes in FFM (1.2 ± 1.6 kg) and FM (-0.7 ± 1.5 kg) (P sports, and age. The mean negative EB observed over the season resulted from the rate of FM use and FFM accretion, but with a large variation by sex and sports. TBW, but not total-body protein or mineral balance, explained the magnitude of EB, which means that athletes under a positive or a negative EB showed a TBW expansion or shrinkage, respectively, specifically within the cells, over one athletic season.

Microgravity simulation activates Cdc42 via Rap1GDS1 to promote vascular branch morphogenesis during vasculogenesis

Directory of Open Access Journals (Sweden)

Shouli Wang

2017-12-01

Full Text Available Gravity plays an important role in normal tissue maintenance. The ability of stem cells to repair tissue loss in space through regeneration and differentiation remains largely unknown. To investigate the impact of microgravity on blood vessel formation from pluripotent stem cells, we employed the embryoid body (EB model for vasculogenesis and simulated microgravity by clinorotation. We first differentiated mouse embryonic stem cells into cystic EBs containing two germ layers and then analyzed vessel formation under clinorotation. We observed that endothelial cell differentiation was slightly reduced under clinorotation, whereas vascular branch morphogenesis was markedly enhanced. EB-derived endothelial cells migrated faster, displayed multiple cellular processes, and had higher Cdc42 and Rac1 activity when subjected to clinorotation. Genetic analysis and rescue experiments demonstrated that Cdc42 but not Rac1 is required for microgravity-induced vascular branch morphogenesis. Furthermore, affinity pull-down assay and mass spectrometry identified Rap1GDS1 to be a Cdc42 guanine nucleotide exchange factor, which was upregulated by clinorotation. shRNA-mediated knockdown of Rap1GDS1 selectively suppressed Cdc42 activation and inhibited both baseline and microgravity-induced vasculogenesis. This was rescued by ectopic expression of constitutively active Cdc42. Taken together, these results support the notion that simulated microgravity activates Cdc42 via Rap1GDS1 to promote vascular branch morphogenesis.

Influence of gaseous phase, light and substrate pretreatment on fruit-body formation, lignin degradation and in vitro digestibility of wheat straw fermented with Pleurotus spp

Energy Technology Data Exchange (ETDEWEB)

Kamra, D.N.; Zadrazil, F.

1986-01-01

Wheat straw was fermented in the solid state with Pleurotus sajor-caju and P. eryngii at 25 degrees C under different concentrations of oxygen and carbon dioxide. Lower than 20% oxygen in the gaseous phase adversely affected the loss of organic matter, the lignin degradation and the change in straw digestibility with both species of Pleurotus. Higher concentrations (10%-30%) of carbon dioxide, with 20% oxygen in the atmospshere, slightly decreased the loss of lignin and organic matter when compared with the losses under oxygen or air. In spite of better lignin degradation by P. sajor-caju, the process efficiency with P. eryngii was higher, because of lower loss of organic matter during the fermentation. Fruit-bodies were not formed by P. eryngii during the period of experiment in any of the treatments. In P. sajor-caju, fruit-bodies were only formed either in flasks closed with cotton plugs or supplied with a continuous flow of sterile air. Carbon dioxide inhibited the process of primordia initiation and fruit-body development. A short exposure (20 minutes per day) to light was essential for primordia and fruit-body formation. The substrate changes and process efficiency with respect to increase in digestibility were much higher in darkness than in light. Light leads to intensive fruit-body production and a different pattern of substrate degradation. The indigenous microflora of wheat straw inhibited fruit-body formation and caused a higher organic matter loss, accompanied by a decrease in digestibility of the fermented wheat straw. 33 references.

Buddhism and the formation of the religious body: a Foucauldian approach

Directory of Open Access Journals (Sweden)

Malcolm Voyce

2011-01-01

Full Text Available Poststructuralist debates around the body have demonstrated how our knowledge of the body is constituted in specific cultural and historical circumstances and in the context of particular relations of power. This article develops this approach to the body in Buddhism and thus attempts to show how the body has been represented within different discourses in Buddhist texts. Implicit in this account is the remedying of the failure in some Buddhist scholarship to recognise different types of bodies (negative and positive and to show how these aspects of the body, as enumerated by texts, operate together to constitute forms of identities capable of being constituted within different historical moments out of the pressure of new social and material changes. At the same time the body is seen as being capable of self modification in terms of that discourse. The term ‘body’ is used here in the sense that it implies not only a physical aspect (flesh, bones, liquids etc., but that it is connected to various cognitive and emotional capacities as outlined in the khandhas (see below explanation of the human constitution. The author's concern in his treatment of the body is to avoid the problems of psychological analysis, as this form of analysis often implies the existence of a psyche or soul along with the ideas of complete individual self-determination.

A Sordaria macrospora mutant lacking the leu1 gene shows a developmental arrest during fruiting body formation.

Science.gov (United States)

Kück, Ulrich

2005-10-01

Developmental mutants with defects in fruiting body formation are excellent resources for the identification of genetic components that control cellular differentiation processes in filamentous fungi. The mutant pro4 of the ascomycete Sordaria macrospora is characterized by a developmental arrest during the sexual life cycle. This mutant generates only pre-fruiting bodies (protoperithecia), and is unable to form ascospores. Besides being sterile, pro4 is auxotrophic for leucine. Ascospore analysis revealed that the two phenotypes are genetically linked. After isolation of the wild-type leu1 gene from S. macrospora, complementation experiments demonstrated that the gene was able to restore both prototrophy and fertility in pro4. To investigate the control of leu1 expression, other genes involved in leucine biosynthesis specifically and in the general control of amino acid biosynthesis ("cross-pathway control") have been analysed using Northern hybridization and quantitative RT-PCR. These analyses demonstrated that genes of leucine biosynthesis are transcribed at higher levels under conditions of amino acid starvation. In addition, the expression data for the cpc1 and cpc2 genes indicate that cross-pathway control is superimposed on leucine-specific regulation of fruiting body development in the leu1 mutant. This was further substantiated by growth experiments in which the wild-type strain was found to show a sterile phenotype when grown on a medium containing the amino acid analogue 5-methyl-tryptophan. Taken together, these data show that pro4 represents a novel mutant type in S. macrospora, in which amino acid starvation acts as a signal that interrupts the development of the fruiting body.

Formation Mechanism and Binding Energy for Body-Centred Regular Icosahedral Structure of Li13 Cluster

International Nuclear Information System (INIS)

Liu Weina; Li Ping; Gou Qingquan; Zhao Yanping

2008-01-01

The formation mechanism for the body-centred regular icosahedral structure of Li 13 cluster is proposed. The curve of the total energy versus the separation R between the nucleus at the centre and nuclei at the apexes for this structure of Li 13 has been calculated by using the method of Gou's modified arrangement channel quantum mechanics (MACQM). The result shows that the curve has a minimal energy of -96.951 39 a.u. at R = 5.46a 0 . When R approaches to infinity, the total energy of thirteen lithium atoms has the value of -96.564 38 a.u. So the binding energy of Li 13 with respect to thirteen lithium atoms is 0.387 01 a.u. Therefore the binding energy per atom for Li 13 is 0.029 77 a.u. or 0.810 eV, which is greater than the binding energy per atom of 0.453 eV for Li 2 , 0.494 eV for Li 3 , 0.7878 eV for Li 4 , 0.632 eV for Li 5 , and 0.674 eV for Li 7 calculated by us previously. This means that the Li 13 cluster may be formed stably in a body-centred regular icosahedral structure with a greater binding energy

WANDERINGS: RESEARCH AND FORMATION AS A SUBJECTIFYING PROCESSUALITY

Directory of Open Access Journals (Sweden)

Juliano dos Santos

2016-12-01

Full Text Available This work seeks to explore the relationship between body, subjectivity, and formation of some aspects that involve the “making of research,” whose implementation took place between 2013 and 2015. The cartography (DELEUZE; GUATTARI, 2011; PASSOS et all, 2009; ROLNIK, 1989 elected by us as a method strived to accompany encounters with bodies, dance, contact improvisation, bio-dance, and lives in formation: “Dance and body expression.” This activity was integrated, in the second semester of 2013, the set of activities of the pedagogical axis “Interações Culturais e Humanísticas” at the Universidade Federal do Paraná, Setor Litoral. There were some contributions to the field of education through the intensities mobilized during the research’s production. The process of formation of a researcher presenting smaller elements, minor elements, not teaching itself, the representation or the discovery of the world, but research, movement, doubt, and the invention of worlds, mediation of desire. In this sense, the text that we present proposes a point out some encounters that resonated with the body of the researcher and b explore the effects that, in intensity, mobilized and continue to mobilize a process of formation. Keywords: Formation. Experimentation. Body. Subjectivity.

Sequencing of the Chlamydophila psittaci ompA Gene Reveals a New Genotype, E/B, and the Need for a Rapid Discriminatory Genotyping Method

Science.gov (United States)

Geens, Tom; Desplanques, Ann; Van Loock, Marnix; Bönner, Brigitte M.; Kaleta, Erhard F.; Magnino, Simone; Andersen, Arthur A.; Everett, Karin D. E.; Vanrompay, Daisy

2005-01-01

Twenty-one avian Chlamydophila psittaci isolates from different European countries were characterized using ompA restriction fragment length polymorphism, ompA sequencing, and major outer membrane protein serotyping. Results reveal the presence of a new genotype, E/B, in several European countries and stress the need for a discriminatory rapid genotyping method. PMID:15872282

Nuclear LSm8 affects number of cytoplasmic processing bodies via controlling cellular distribution of Like-Sm proteins

Czech Academy of Sciences Publication Activity Database

Novotný, Ivan; Podolská, Kateřina; Blažíková, Michaela; Valášek, Leoš Shivaya; Svoboda, Petr; Staněk, David

2012-01-01

Roč. 23, č. 19 (2012), s. 3776-3785 ISSN 1059-1524 R&D Projects: GA AV ČR KAN200520801; GA ČR GA204/07/0133; GA ČR GAP305/10/2215; GA ČR GAP302/11/1910; GA ČR(CZ) GBP305/12/G034 Institutional research plan: CEZ:AV0Z50390703; CEZ:AV0Z50520514; CEZ:AV0Z50200510 Institutional support: RVO:68378050 ; RVO:68378041 ; RVO:61388971 Keywords : P-bodies * LSm proteins * mRNA degradation Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 4.604, year: 2012

An ebCMOS camera system for marine bioluminescence observation: The LuSEApher prototype

Energy Technology Data Exchange (ETDEWEB)

Dominjon, A., E-mail: a.dominjon@ipnl.in2p3.fr [CNRS/IN2P3, Institut de Physique Nucleaire de Lyon, Villeurbanne F-69622 (France); Ageron, M. [CNRS/IN2P3, Centre de Physique des Particules de Marseille, Marseille, F-13288 (France); Barbier, R. [CNRS/IN2P3, Institut de Physique Nucleaire de Lyon, Villeurbanne F-69622 (France); Universite de Lyon, Universite Lyon 1, Lyon F-69003 (France); Billault, M.; Brunner, J. [CNRS/IN2P3, Centre de Physique des Particules de Marseille, Marseille, F-13288 (France); Cajgfinger, T. [CNRS/IN2P3, Institut de Physique Nucleaire de Lyon, Villeurbanne F-69622 (France); Universite de Lyon, Universite Lyon 1, Lyon F-69003 (France); Calabria, P. [CNRS/IN2P3, Institut de Physique Nucleaire de Lyon, Villeurbanne F-69622 (France); Chabanat, E. [CNRS/IN2P3, Institut de Physique Nucleaire de Lyon, Villeurbanne F-69622 (France); Universite de Lyon, Universite Lyon 1, Lyon F-69003 (France); Chaize, D.; Doan, Q.T.; Guerin, C.; Houles, J.; Vagneron, L. [CNRS/IN2P3, Institut de Physique Nucleaire de Lyon, Villeurbanne F-69622 (France)

2012-12-11

The ebCMOS camera, called LuSEApher, is a marine bioluminescence recorder device adapted to extreme low light level. This prototype is based on the skeleton of the LUSIPHER camera system originally developed for fluorescence imaging. It has been installed at 2500 m depth off the Mediterranean shore on the site of the ANTARES neutrino telescope. The LuSEApher camera is mounted on the Instrumented Interface Module connected to the ANTARES network for environmental science purposes (European Seas Observatory Network). The LuSEApher is a self-triggered photo detection system with photon counting ability. The presentation of the device is given and its performances such as the single photon reconstruction, noise performances and trigger strategy are presented. The first recorded movies of bioluminescence are analyzed. To our knowledge, those types of events have never been obtained with such a sensitivity and such a frame rate. We believe that this camera concept could open a new window on bioluminescence studies in the deep sea.

The TT, TB, EB and BB correlations in anisotropic inflation

Energy Technology Data Exchange (ETDEWEB)

Chen, Xingang [Department of Physics, The University of Texas at Dallas, Richardson, TX 75083 (United States); Emami, Razieh [School of Physics, Institute for Research in Fundamental Sciences (IPM), P. O. Box 19395-5531, Tehran (Iran, Islamic Republic of); Firouzjahi, Hassan [School of Astronomy, Institute for Research in Fundamental Sciences (IPM), P. O. Box 19395-5531, Tehran (Iran, Islamic Republic of); Wang, Yi, E-mail: Xingang.Chen@utdallas.edu, E-mail: emami@ipm.ir, E-mail: firouz@ipm.ir, E-mail: yw366@cam.ac.uk [Centre for Theoretical Cosmology, DAMTP, University of Cambridge, Cambridge CB3 0WA (United Kingdom)

2014-08-01

The ongoing and future experiments will measure the B-mode from different sky coverage and frequency bands, with the potential to reveal non-trivial features in polarization map. In this work we study the TT, TB, EB and BB correlations associated with the B-mode polarization of CMB map in models of charged anisotropic inflation. The model contains a chaotic-type large field complex inflaton which is charged under the U(1) gauge field. We calculate the statistical anisotropies generated in the power spectra of the curvature perturbation, the tensor perturbation and their cross-correlation. It is shown that the asymmetry in tensor power spectrum is a very sensitive probe of the gauge coupling. While the level of statistical anisotropy in temperature power spectrum can be small and satisfy the observational bounds, the interactions from the gauge coupling can induce large directional dependence in tensor modes. This will leave interesting anisotropic fingerprints in various correlations involving the B-mode polarization such as the TB cross-correlation which may be detected in upcoming Planck polarization data. In addition, the TT correlation receives an anisotropic contribution from the tensor sector which naturally decays after l ∼> 100. We expect that the mechanism of using tensor sector to induce asymmetry at low l to be generic which can also be applied to address other low l CMB anomalies.

Coilin phosphomutants disrupt Cajal body formation, reduce cell proliferation and produce a distinct coilin degradation product.

Directory of Open Access Journals (Sweden)

Zunamys I Carrero

Full Text Available Coilin is a nuclear phosphoprotein that accumulates in Cajal bodies (CBs. CBs participate in ribonucleoprotein and telomerase biogenesis, and are often found in cells with high transcriptional demands such as neuronal and cancer cells, but can also be observed less frequently in other cell types such as fibroblasts. Many proteins enriched within the CB are phosphorylated, but it is not clear what role this modification has on the activity of these proteins in the CB. Coilin is considered to be the CB marker protein and is essential for proper CB formation and composition in mammalian cells. In order to characterize the role of coilin phosphorylation on CB formation, we evaluated various coilin phosphomutants using transient expression. Additionally, we generated inducible coilin phosphomutant cell lines that, when used in combination with endogenous coilin knockdown, allow for the expression of the phosphomutants at physiological levels. Transient expression of all coilin phosphomutants except the phosphonull mutant (OFF significantly reduces proliferation. Interestingly, a stable cell line induced to express the coilin S489D phosphomutant displays nucleolar accumulation of the mutant and generates a N-terminal degradation product; neither of which is observed upon transient expression. A N-terminal degradation product and nucleolar localization are also observed in a stable cell line induced to express a coilin phosphonull mutant (OFF. The nucleolar localization of the S489D and OFF coilin mutants observed in the stable cell lines is decreased when endogenous coilin is reduced. Furthermore, all the phosphomutant cells lines show a significant reduction in CB formation when compared to wild-type after endogenous coilin knockdown. Cell proliferation studies on these lines reveal that only wild-type coilin and the OFF mutant are sufficient to rescue the reduction in proliferation associated with endogenous coilin depletion. These results emphasize

Higher accumulation of F1-V fusion recombinant protein in plants after induction of protein body formation.

Science.gov (United States)

Alvarez, M Lucrecia; Topal, Emel; Martin, Federico; Cardineau, Guy A

2010-01-01

Improving foreign protein accumulation is crucial for enhancing the commercial success of plant-based production systems since product yields have a major influence on process economics. Cereal grain evolved to store large amounts of proteins in tightly organized aggregates. In maize, gamma-Zein is the major storage protein synthesized by the rough endoplasmic reticulum (ER) and stored in specialized organelles called protein bodies (PB). Zera (gamma-Zein ER-accumulating domain) is the N-terminal proline-rich domain of gamma-zein that is sufficient to induce the assembly of PB formation. Fusion of the Zera domain to proteins of interest results in assembly of dense PB-like, ER-derived organelles, containing high concentration of recombinant protein. Our main goal was to increase recombinant protein accumulation in plants in order to enhance the efficiency of orally-delivered plant-made vaccines. It is well known that oral vaccination requires substantially higher doses than parental formulations. As a part of a project to develop a plant-made plague vaccine, we expressed our model antigen, the Yersinia pestis F1-V antigen fusion protein, with and without a fused Zera domain. We demonstrated that Zera-F1-V protein accumulation was at least 3x higher than F1-V alone when expressed in three different host plant systems: Ncotiana benthamiana, Medicago sativa (alfalfa) and Nicotiana tabacum NT1 cells. We confirmed the feasibility of using Zera technology to induce protein body formation in non-seed tissues. Zera expression and accumulation did not affect plant development and growth. These results confirmed the potential exploitation of Zera technology to substantially increase the accumulation of value-added proteins in plants.

Toxic effects of sub-chronic exposure of male albino rats to emamectin benzoate and possible ameliorative role of Foeniculum vulgare essential oil.

Science.gov (United States)

El-Sheikh, El-Sayed A; Galal, Azza A A

2015-05-01

Emamectin benzoate (EB) is an avermectin insecticide used extensively in pest control on vegetable and field crops. Few studies have been done for evaluating adverse effects of EB. In the current study, we evaluated the toxic effects of EB on male rats and the possible ameliorative role of fennel essential oil (FEO). Thirty two male rats were randomly divided into 4 equal groups. All groups were treated orally with distilled water (control group), 0.5mlFEOkg(-1) BW (FEO group), 2.5mgEBkg(-1) BW (EB group), and 0.5mlFEOkg(-1) BW+2.5mgEBkg(-1) BW (FEO+EB group) for 28 days. The obtained results showed that EB treatment resulted in a significant decrease in body weight, body weight gain, RBC count, Hb concentration, % PCV, MCV and MCHC. Moreover, EB significantly decreased total leukocyte, lymphocyte, monocyte and platelet count but significantly increased granulocyte count. EB markedly decreased total protein, albumin, globulin, IgG and IgM concentrations with a significant increase in TNF-α secretion. EB had a negative impact on the liver as it significantly increased ALT, ALP, and MDA, while decreasing SOD activity. Regarding to the histopathological examination, EB treatment induced coagulative necrosis and blood vessels congestion of the liver in treated rats. Furthermore, it resulted in depletion and necrosis of the white pulp of the spleen in treated rats. The co-administration of FEO with EB, however, improved the majority of parameters studied, suggesting that FEO is an important substance in decreasing toxic effects of EB. Copyright © 2015 Elsevier B.V. All rights reserved.

SSX2 is a novel DNA-binding protein that antagonizes polycomb group body formation and gene repression

DEFF Research Database (Denmark)

Gjerstorff, Morten Frier; Relster, Mette Marie; Greve, Katrine Buch Viden

2014-01-01

Polycomb group (PcG) complexes regulate cellular identity through epigenetic programming of chromatin. Here, we show that SSX2, a germline-specific protein ectopically expressed in melanoma and other types of human cancers, is a chromatin-associated protein that antagonizes BMI1 and EZH2 PcG body...... formation and derepresses PcG target genes. SSX2 further negatively regulates the level of the PcG-associated histone mark H3K27me3 in melanoma cells, and there is a clear inverse correlation between SSX2/3 expression and H3K27me3 in spermatogenesis. However, SSX2 does not affect the overall composition...

Increase of Total Body Water with Decrease of Body Mass while Running 100 km Nonstop--Formation of Edema?

Science.gov (United States)

Knechtle, Beat; Wirth, Andrea; Knechtle, Patrizia; Rosemann, Thomas

2009-01-01

We investigated whether ultraendurance runners in a 100-km run suffer a decrease of body mass and whether this loss consists of fat mass, skeletal muscle mass, or total body water. Male ultrarunners were measured pre- and postrace to determine body mass, fat mass, and skeletal muscle mass by using the anthropometric method. In addition,…

Healthy Body Image Intervention Delivered to Young Women via Facebook Groups: Formative Study of Engagement and Acceptability.

Science.gov (United States)

Stapleton, Jerod L; Manne, Sharon L; Day, Ashley K; Levonyan-Radloff, Kristine; Pagoto, Sherry L

2018-02-20

There is increasing interest in using social media sites such as Facebook to deliver health interventions so as to expose people to content while they are engaging in their usual social media habit. This formative intervention development study is novel in describing a preliminary test of using the secret group feature of Facebook to deliver a behavioral intervention targeting users of indoor tanning beds to reduce their risk of skin cancer. Intervention content was designed to challenge body image-related constructs associated with indoor tanning through the use of dissonance-inducing content. To evaluate engagement with and acceptability of using a secret Facebook group to deliver a healthy body image intervention to young women engaged in indoor tanning. Seventeen young women completed a baseline survey and joined a secret Facebook group with intervention content delivered via daily posts for 4 weeks. Engagement data was extracted and acceptability was measured via a follow-up survey. The study had a high retention rate (94%, [16/17]). On average, posts were viewed by 91% of participants, liked by 35%, and commented on by 26%. The average comment rate was highest (65%) for posts that elicited comments by directly posing questions or discussion topics to the group. Average intervention acceptability ratings were highly positive and participants reported feeling connected to the group and its topic. Average rates of past 1-month indoor tanning reported following the intervention were lower than the baseline rate (P=.08, Cohen d=0.47). This study is novel in demonstrating participant engagement with and acceptability of using Facebook secret groups to deliver a dissonance-inducing intervention approach that utilizes group-based discussions related to body image. The study is also unique within the field of skin cancer prevention by demonstrating the potential value of delivering an indoor tanning intervention within an interactive social media format. The findings

Healthy Body Image Intervention Delivered to Young Women via Facebook Groups: Formative Study of Engagement and Acceptability

Science.gov (United States)

Manne, Sharon L; Day, Ashley K; Levonyan-Radloff, Kristine; Pagoto, Sherry L

2018-01-01

Background There is increasing interest in using social media sites such as Facebook to deliver health interventions so as to expose people to content while they are engaging in their usual social media habit. This formative intervention development study is novel in describing a preliminary test of using the secret group feature of Facebook to deliver a behavioral intervention targeting users of indoor tanning beds to reduce their risk of skin cancer. Intervention content was designed to challenge body image-related constructs associated with indoor tanning through the use of dissonance-inducing content. Objective To evaluate engagement with and acceptability of using a secret Facebook group to deliver a healthy body image intervention to young women engaged in indoor tanning. Methods Seventeen young women completed a baseline survey and joined a secret Facebook group with intervention content delivered via daily posts for 4 weeks. Engagement data was extracted and acceptability was measured via a follow-up survey. Results The study had a high retention rate (94%, [16/17]). On average, posts were viewed by 91% of participants, liked by 35%, and commented on by 26%. The average comment rate was highest (65%) for posts that elicited comments by directly posing questions or discussion topics to the group. Average intervention acceptability ratings were highly positive and participants reported feeling connected to the group and its topic. Average rates of past 1-month indoor tanning reported following the intervention were lower than the baseline rate (P=.08, Cohen d=0.47). Conclusions This study is novel in demonstrating participant engagement with and acceptability of using Facebook secret groups to deliver a dissonance-inducing intervention approach that utilizes group-based discussions related to body image. The study is also unique within the field of skin cancer prevention by demonstrating the potential value of delivering an indoor tanning intervention within

Nonverbal behavior in soccer: the influence of dominant and submissive body language on the impression formation and expectancy of success of soccer players.

Science.gov (United States)

Furley, Philip; Dicks, Matt; Memmert, Daniel

2012-02-01

In the present article, we investigate the effects of specific nonverbal behaviors signaling dominance and submissiveness on impression formation and outcome expectation in the soccer penalty kick situation. In Experiment 1, results indicated that penalty takers with dominant body language are perceived more positively by soccer goalkeepers and players and are expected to perform better than players with a submissive body language. This effect was similar for both video and point-light displays. Moreover, in contrast to previous studies, we found no effect of clothing (red vs. white) in the video condition. In Experiment 2, we used the implicit association test to demonstrate that dominant body language is implicitly associated with a positive soccer player schema whereas submissive body language is implicitly associated with a negative soccer player schema. The implications of our findings are discussed with reference to future implications for theory and research in the study of person perception in sport.

Analysis of VIA and EbA in a River Bank Erosion Prone Area of Bangladesh Applying DPSIR Framework

Directory of Open Access Journals (Sweden)

Syed Hafizur Rahman

2016-10-01

Full Text Available This study aims to set up a comprehensive approach to the Vulnerability and Impact Assessment (VIA of river erosion and to suggest Ecosystem-based Adaptation (EbA practices. Based on the analysis of vulnerability using the Driver-Pressure-State-Impact-Response (DPSIR framework, this paper discusses some of the significant climatic (rainfall pattern, temperature, seasonal drift, cold wave and heat wave and non-climatic (river erosion, repetitive death of field crops and agrochemicals forces in the Kazipur Upazila (Sirajganj District—a river erosion-prone area of Bangladesh. Both primary (Key Informants Interview, Household Survey, and Focus Group Discussion and secondary (climatic, literature review data have been used in revealing the scenario of climatic stress. The analysis revealed a slightly increasing trend of mean annual temperature, and a decreasing trend of total annual rainfall from 1981 to 2015, which have been supported by people’s perception. This study found that river erosion, the increase of temperature and the late arrival of monsoon rain, excessive monsoon rainfall, high use of agrochemicals, and flow alterations are major drivers in the riverine ecosystem. These drivers are creating pressures on agricultural land, soil fertility, water availability and livelihood patterns of affected communities. Hence, floating bed cultivation, integrated pest management, use of cover crops, reforestation, the introduction of an agro-weather forecasting system, and a new variety of flood tolerant species have been suggested as potential EbA to cope with river bank erosion and to increase the capacity of the affected ecosystem.

The transcriptional regulatory network of Corynebacterium jeikeium K411 and its interaction with metabolic routes contributing to human body odor formation.

Science.gov (United States)

Barzantny, Helena; Schröder, Jasmin; Strotmeier, Jasmin; Fredrich, Eugenie; Brune, Iris; Tauch, Andreas

2012-06-15

Lipophilic corynebacteria are involved in the generation of volatile odorous products in the process of human body odor formation by degrading skin lipids and specific odor precursors. Therefore, these bacteria represent appropriate model systems for the cosmetic industry to examine axillary malodor formation on the molecular level. To understand the transcriptional control of metabolic pathways involved in this process, the transcriptional regulatory network of the lipophilic axilla isolate Corynebacterium jeikeium K411 was reconstructed from the complete genome sequence. This bioinformatic approach detected a gene-regulatory repertoire of 83 candidate proteins, including 56 DNA-binding transcriptional regulators, nine two-component systems, nine sigma factors, and nine regulators with diverse physiological functions. Furthermore, a cross-genome comparison among selected corynebacterial species of the taxonomic cluster 3 revealed a common gene-regulatory repertoire of 44 transcriptional regulators, including the MarR-like regulator Jk0257, which is exclusively encoded in the genomes of this taxonomical subline. The current network reconstruction comprises 48 transcriptional regulators and 674 gene-regulatory interactions that were assigned to five interconnected functional modules. Most genes involved in lipid degradation are under the combined control of the global cAMP-sensing transcriptional regulator GlxR and the LuxR-family regulator RamA, probably reflecting the essential role of lipid degradation in C. jeikeium. This study provides the first genome-scale in silico analysis of the transcriptional regulation of metabolism in a lipophilic bacterium involved in the formation of human body odor. Copyright © 2012 Elsevier B.V. All rights reserved.

Comparison of orthogonal kilovolt X-ray images and cone-beam CT matching results in setup error assessment and correction for EB-PBI during free breathing

International Nuclear Information System (INIS)

Wang Wei; Li Jianbin; Hu Hongguang; Ma Zhifang; Xu Min; Fan Tingyong; Shao Qian; Ding Yun

2014-01-01

Objective: To compare the differences in setup error (SE) assessment and correction between the orthogonal kilovolt X-ray images and CBCT in EB-PBI patients during free breathing. Methods: Nineteen patients after breast conserving surgery EB-PBI were recruited. Interfraction SE was acquired using orthogonal kilovolt X-ray setup images and CBCT, after on-line setup correction,calculate the residual error and compare the SE, residual error and setup margin (SM) quantified for orthogonal kilovolt X-ray images and CBCT. Wilcoxon sign-rank test was used to evaluate the differences. Results: The CBCT based SE (systematic error, ∑) was smaller than the orthogonal kilovolt X-ray images based ∑ in AP direction (-1.2 mm vs 2.00 mm; P=0.005), and there was no statistically significant differences for three dimensional directions in random error (σ) (P=0.948, 0.376, 0.314). After on-line setup correction,CBCT decreases setup residual error than the orthogonal kilovolt X-ray images in AP direction (Σ: -0.20 mm vs 0.50 mm, P=0.008; σ: 0.45 mm vs 1.34 mm, P=0.002). And also the CBCT based SM was smaller than orthogonal kilovolt X-ray images based SM in AP direction (Σ: -1.39 mm vs 5.57 mm, P=0.003; σ: 0.00 mm vs 3.2 mm, P=0.003). Conclusions: Compared with kilovolt X-ray images, CBCT underestimate the setup error in the AP direction, but decreases setup residual error significantly.An image-guided radiotherapy and setup error assessment using kilovolt X-ray images for EB-PBI plans was feasible. (authors)

A rare case of pelvic foreign body: foley catheter migration from the uterus to peritoneal cavity, perforating rectosigmoid colon and abscess formation

Directory of Open Access Journals (Sweden)

F Sajjadian

2017-04-01

Full Text Available Background: Intraperitoneal foreign body is an unusual complication of abdomino pelvic surgery. In rare condition introduction of foreign body into the uterus, may be perforated and migrated to the adjacent organs. CasePresentation: A 41-year old woman with chronic abdominal pain was referred to the Imaging Center  for doing  Computed Tomography (CT scan  . A computed tomography of abdominopelvic demonstrated foley catheter in the pelvis with abscess.The patients have not had any abdominopelvic surgery. She had undergone criminal abortion by home midwife with the use of foley catheter 6 years ago. Laparatomy was done, foley catheter removed and abscess was evacuated. Conclusion:  The abdominopelvic foreign body is a rare condition in non operativepatients, it should be included in the differential diagnosis of abscess formation that was  detected in patients with a history of chronic abdominal pain.

Electron tomography and cryo-SEM characterization reveals novel ultrastructural features of host-parasite interaction during Chlamydia abortus infection.

Science.gov (United States)

Wilkat, M; Herdoiza, E; Forsbach-Birk, V; Walther, P; Essig, A

2014-08-01

Chlamydia (C.) abortus is a widely spread pathogen among ruminants that can be transmitted to women during pregnancy leading to severe systemic infection with consecutive abortion. As a member of the Chlamydiaceae, C. abortus shares the characteristic feature of an obligate intracellular biphasic developmental cycle with two morphological forms including elementary bodies (EBs) and reticulate bodies (RBs). In contrast to other chlamydial species, C. abortus ultrastructure has not been investigated yet. To do so, samples were fixed by high-pressure freezing and processed by different electron microscopic methods. Freeze-substituted samples were analysed by transmission electron microscopy, scanning transmission electron microscopical tomography and immuno-electron microscopy, and freeze-fractured samples were analysed by cryo-scanning electron microscopy. Here, we present three ultrastructural features of C. abortus that have not been reported up to now. Firstly, the morphological evidence that C. abortus is equipped with the type three secretion system. Secondly, the accumulation and even coating of whole inclusion bodies by membrane complexes consisting of multiple closely adjacent membranes which seems to be a C. abortus specific feature. Thirdly, the formation of small vesicles in the periplasmic space of RBs in the second half of the developmental cycle. Concerning the time point of their formation and the fact that they harbour chlamydial components, these vesicles might be morphological correlates of an intermediate step during the process of redifferentiation of RBs into EBs. As this feature has also been shown for C. trachomatis and C. pneumoniae, it might be a common characteristic of the family of Chlamydiaceae.

Planetesimals and Planet Formation

Science.gov (United States)

Chambers, John

The first step in the standard model for planet formation is the growth of gravitationally bound bodies called ``planetesimals'' from dust grains in a protoplanetary disk. Currently, we do not know how planetesimals form, how long they take to form, or what their sizes and mechanical properties are. The goal of this proposal is to assess how these uncertainties affect subsequent stages of planetary growth and the kind of planetary systems that form. The work will address three particular questions: (i) Can the properties of small body populations in the modern Solar System constrain the properties of planetesimals? (ii) How do the properties of planetesimals affect the formation of giant planets? (iii) How does the presence of a water ice condensation front (the ``snow line'') in a disk affect planetesimal formation and the later stages of planetary growth? These questions will be examined with computer simulations of planet formation using new computer codes to be developed as part of the proposal. The first question will be addressed using a statistical model for planetesimal coagulation and fragmentation. This code will be merged with the proposer's Mercury N-body integrator code to model the dynamics of large protoplanets in order to address the second question. Finally, a self- consistent model of disk evolution and the radial transport of water ice and vapour will be added to examine the third question. A theoretical understanding of how planets form is one of the key goals of NASA and the Origins of Solar Systems programme. Researchers have carried out many studies designed to address this goal, but the questions of how planetesimals form and how their properties affect planet formation have received relatively little attention. The proposed work will help address these unsolved questions, and place other research in context by assessing the importance of planetesimal origins and properties for planet formation.

The impact of rate of weight loss on body composition and compensatory mechanisms during weight reduction

DEFF Research Database (Denmark)

Coutinho, Sílvia Ribeiro; With, Emilie; Rehfeld, Jens F

2018-01-01

BACKGROUND & AIMS: Rapid weight loss (WL) has been associated with a larger loss of fat free mass and a disproportional reduction in resting metabolic rate (RMR), but the evidence is inconclusive. We aimed to evaluate the impact of WL rate on body composition and compensatory mechanisms activated...... with WL (reduced RMR, increased exercise efficiency (ExEff) and appetite), both during negative and neutral energy balance (EB). METHODS: Thirty-five participants with obesity were randomized to lose a similar weight rapidly (4 weeks) or gradually (8 weeks), and afterwards to maintain it (4 weeks). Body...... weight and composition, RMR, ExEff (10, 25 and 50 W), appetite feelings and appetite-regulating hormones (active ghrelin, cholecystokinin, total peptide YY (PYY), active glucagon-like peptide-1 and insulin), in fasting and every 30 min up to 2.5 h, were measured at baseline and after each phase. RESULTS...

The Energy Balance Study: The Design and Baseline Results for a Longitudinal Study of Energy Balance

Science.gov (United States)

Hand, Gregory A.; Shook, Robin P.; Paluch, Amanda E.; Baruth, Meghan; Crowley, E. Patrick; Jaggers, Jason R.; Prasad, Vivek K.; Hurley, Thomas G.; Hebert, James R.; O'Connor, Daniel P.; Archer, Edward; Burgess, Stephanie; Blair, Steven N.

2013-01-01

Purpose: The Energy Balance Study (EBS) was a comprehensive study designed to determine over a period of 12 months the associations of caloric intake and energy expenditure on changes in body weight and composition in a population of healthy men and women. Method: EBS recruited men and women aged 21 to 35 years with a body mass index between 20…

β-hydroxy-β-methylbutyrate (HMB) attenuates muscle and body weight loss in experimental cancer cachexia.

Science.gov (United States)

Aversa, Zaira; Bonetto, Andrea; Costelli, Paola; Minero, Valerio Giacomo; Penna, Fabio; Baccino, Francesco Maria; Lucia, Simone; Rossi Fanelli, Filippo; Muscaritoli, Maurizio

2011-03-01

β-hydroxy-β-methylbutyrate (HMB), a leucine metabolite, improves muscle mass and function. This study aimed at evaluating the effects of HMB administration in an experimental in vivo model of cancer cachexia (CC). Wistar rats were randomized to receive standard or 4% HMB-enriched chow. Rats from both groups were randomized to receive an i.p. inoculum of AH-130 cells (TB). All rats were weighed and sacrificed at day 24. Liver, heart and muscles were dissected and weighed. The protein levels of p-p70S6k, p-eIf2α, p-mTOR and p-4-EB-P1 were evaluated by Western blotting on gastrocnemius muscle (GSN). As expected, the growth of the AH-130 ascites hepatoma induced significant carcass weight and GSN muscle loss. HMB treatment significantly increased GSN and heart weight in controls (p=0.002 and pHMB-treated TB, body weight was not lost but significantly (p=0.003) increased, and GSN loss was significantly (p=0.04) attenuated with respect to TB. Phosphorylated eIF2α markedly decreased in TB-rats vs. C. Feeding the HMB-enriched diet resulted in decreased p-eIF2α levels in control animals, while no changes could be observed in the TB group. Phosphorylated p70S6K and phosphorylated mTOR were markedly increased by HMB treatment in controls and further increased in TB. Phosphorylated 4-EB-P1 was markedly increased in TB but substantially unaffected by HMB treatment. Administration of HMB attenuates body weight and muscle loss in experimental CC. Increased phosphorylation of key anabolic molecules suggests that these actions are mediated by improved protein anabolism in muscle.

Mechanical properties of TIG and EB weld joints of F82H

Energy Technology Data Exchange (ETDEWEB)

Hirose, Takanori, E-mail: hirose.takanori@jaea.go.jp; Sakasegawa, Hideo; Nakajima, Motoki; Tanigawa, Hiroyasu

2015-10-15

Highlights: • Narrow groove TIG minimized volume of F82H weld. • Mechanical properties of TIG and EB welds of F82H have been characterized. • Post weld heat treatment successfully moderate the toughness of weld metal without softening the base metal. - Abstract: This work investigates mechanical properties of weld joints of a reduced activation ferritic/martensitic steel, F82H and effects of post weld heat treatment on the welds. Vickers hardness, tensile and Charpy impact tests were conducted on F82H weld joints prepared using tungsten-inert-gas and electron beam after various heat treatments. Although narrow groove tungsten-inert-gas welding reduced volume of weld bead, significant embrittlement was observed in a heat affected zone transformed due to heat input. Post weld heat treatment above 993 K successfully moderated the brittle transformed region. The hardness of the brittle region strongly depends on the heat treatment temperature. Meanwhile, strength of base metal was slightly reduced by the treatment at temperature ranging from 993 to 1053 K. Moreover, softening due to double welding was observed only in the weld metal, but negligible in base metal.

Decision making models and human factors: TOPSIS and Ergonomic Behaviors (TOPSIS-EB

Directory of Open Access Journals (Sweden)

Mohammad

2017-02-01

Full Text Available An effective safety management requires attention to human factors as well as system compo-nents which make risky or safe situations at technical components. This study evaluates and ana-lyze ergonomic behaviors in order to select the best work shift group in an Iranian process in-dustry, in 2010.The methodology was based on the Ergonomic Behavior Sampling (EBS, and TOPSIS method. After specifying the unergonomic behaviors and with reference to the results of a pilot study, a sample of 1755 was determined, with a sampling accuracy of 5% and confi-dence level of 95%. However, in order to gain more confidence, 2631 observations were collect-ed. The results indicate that 43.6% of workers’ behaviors were unergonomic. The most frequent unergonomic behavior was amusing of legs while load lifting with 83.01% of total unergonomic behaviors observations. Using TOPSIS method, the most effective shift group and the least at-tractive alternatives for intervention were selected in this company. Findings declare high number of unergonomic behaviors. Catastrophic consequences of accidents in petrochemical industry ne-cessitate attention to workers’ ergonomic behaviors in the workplace and promotion of them.

Evaluation of hollow fiber culture for large-scale production of mouse embryonic stem cell-derived hematopoietic stem cells.

Science.gov (United States)

Nakano, Yu; Iwanaga, Shinya; Mizumoto, Hiroshi; Kajiwara, Toshihisa

2018-03-03

Hematopoietic stem cells (HSCs) have the ability to differentiate into all types of blood cells and can be transplanted to treat blood disorders. However, it is difficult to obtain HSCs in large quantities because of the shortage of donors. Recent efforts have focused on acquiring HSCs by differentiation of pluripotent stem cells. As a conventional differentiation method of pluripotent stem cells, the formation of embryoid bodies (EBs) is often employed. However, the size of EBs is limited by depletion of oxygen and nutrients, which prevents them from being efficient for the production of HSCs. In this study, we developed a large-scale hematopoietic differentiation approach for mouse embryonic stem (ES) cells by applying a hollow fiber (HF)/organoid culture method. Cylindrical organoids, which had the potential for further spontaneous differentiation, were established inside of hollow fibers. Using this method, we improved the proliferation rate of mouse ES cells to produce an increased HSC population and achieved around a 40-fold higher production volume of HSCs in HF culture than in conventional EB culture. Therefore, the HF/organoid culture method may be a new mass culture method to acquire pluripotent stem cell-derived HSCs.

Projekt v prostředí sportovních a tělovýchovných služeb - Rekondiční centrum Brno

OpenAIRE

Musilová, Erika

2015-01-01

Bakalářská práce řeší projekt v prostředí sportovních a tělovýchovných služeb.práce je zpracovat projekt rekondičního centra. Bakalářská práce vychází z analýzy zařízení a z porovnání center stejného typu v jiných městech České republiky. Práce uvádí vlastní návrhy na zlepšení služeb rekondičního centra v Brně a celé sítě rekondičních center formou franchisingu. This bachelor's thesis deals with a project in the sports and physical education environment. The target is to develop a project ...

Synthesis and characterization of PEFC membranes based on fluorinated-polymer-alloy using pre-soft-EB grafting method

International Nuclear Information System (INIS)

Muto, Fumihiro; Oshima, Akihiro; Kakigi, Tomoyuki; Mitani, Naohiro; Matsuura, Akio; Fujii, Kazuki; Sato, Yukiko; Li Jingye; Washio, Masakazu

2007-01-01

Polymer electrolyte fuel cell (PEFC) membranes based on thin film of crosslinked perfluorinated polymer-alloys (RX-FA) have been fabricated by soft electron beam (soft-EB) grafting with styrene monomers using soft-EB irradiation under nitrogen atmosphere at room temperature (RT). The characteristic properties of styrene-grafted materials (GRX-FA) and sulfonated materials (SRX-FA) have been measured by differential scanning calorimetry (DSC) and FT-IR spectroscopy, ionic conductivity and so on. The glass transition temperatures (dry state) of all obtained SRX-FA were about 105 ± 1 deg. C, which are higher than Nafion. The ion exchange capacities of SRX-FA have been achieved about 3.3 meq/g (dry). The ionic conductivity of obtained SRX-FA has showed about 0.17 S/cm at 60 deg. C with relative humidity (RH) of ∼95%. The ionic conductivities of the obtained SRX-FA were higher than that of conventional perfluoro-sulfonic acid membranes (PFSA). Fabricated membrane electrode assemblies (MEAs) based on the obtained SRX-FA have shown encouraging performance in the PEFC, compared with the conventional PFSA. The power density of obtained MEAs based on the SRX-FA was about 330-340 mW/cm 2 under 500 mA/cm 2 at 60 deg. C operation. Moreover, the maximum power densities of obtained MEAs based on the SRX-FA shows about 630 mW/cm 2 at 60 deg. C. On the other hand, the power density at 500 mA/cm 2 and maximum power density of MEA based on Nafion 112 were about 320 and 590 mW/cm 2 at 60 deg. C. Thus, the power density of the obtained SRX-FA was higher than that of conventional PFSA

Kinetics and equilibria for the formation of a new DNA metal-intercalator: the cyclic polyamine Neotrien/copper(II) complex.

Science.gov (United States)

Biver, Tarita; Secco, Fernando; Tinè, Maria Rosaria; Venturini, Marcella

2004-01-01

A study has been performed of the kinetics and equilibria involved in complex formation between the macrocyclic polyamine 2,5,8,11-tetraaza[12]-[12](2,9)[1,10]-phenanthrolinophane (Neotrien) and Cu(II) in acidic aqueous solution and ionic strength 0.5 M (NaCl), by means of the stopped-flow method and UV spectrophotometry. Spectrophotometric titrations and kinetic experiments revealed that the binding of Cu(II) to Neotrien gives rise to several 1:1 complexes differing in their degree of protonation. Under the experimental hydrogen ion concentration range investigated, complexation occurs by two parallel paths: (a) M2+ + (H4L)4+ (MH4L)6+ and (b) M2+ + (H3L)3+ (MH3L)5+. The rate constants values found for complex formation, by paths (a) and (b), are much lower than the values expected from water exchange at copper(II) and other amine/Cu(II) complexation kinetic constants. Kinetic experiments at different NaCl concentrations indicated that this finding was not due to chloride ion competition in complex formation with Neotrien, but it was related to a ring rigidity effect. As the phenanthroline moiety could, in principle, interact with nucleic acids by intercalation or external binding, some preliminary measurements concerned with the possible interactions occurring between the Cu(II)/Neotrien complex and calf thymus DNA (CT-DNA) have also been carried out. The absorption spectra of the Cu(II)/Neotrien complex change upon addition of CT-DNA at pH 7.0, revealing the occurrence of complex-nucleic acid interactions. Moreover, fluorescence titrations, carried out by adding the Cu(II)/Neotrien complex to CT-DNA, previously saturated with ethidium bromide (EB), show that the Cu(II)/Neotrien complex is able to displace EB from DNA, suggesting the complex is able to intercalate into the polynucleotide and then to cleave the phosphodiester bond of DNA.

The Arabidopsis mitogen-activated protein kinase 6 is associated with γ-tubulin on microtubules, phosphorylates EB1c and maintains spindle orientation under nitrosative stress

Czech Academy of Sciences Publication Activity Database

Kohoutová, Lucie; Kourová, Hana; Nagy, S. K.; Volc, Jindřich; Halada, Petr; Mészáros, T.; Meskiene, I.; Bögre, L.; Binarová, Pavla

2015-01-01

Roč. 207, č. 4 (2015), s. 1061-1074 ISSN 0028-646X R&D Projects: GA MŠk 7AMB13AT013; GA ČR GAP501/12/2333 Institutional support: RVO:61388971 Keywords : Arabidopsis * cell division * EB1c Subject RIV: EE - Microbiology, Virology Impact factor: 7.210, year: 2015

Political IMRSS body

International Nuclear Information System (INIS)

Gmelin, W.

1996-01-01

When suggesting for discussion a possible role and the utility of an international body for an internationally monitored retrievable storage system (IMRSS), it appears useful to consider its possible advantages and disadvantages to also assess the potential of successfully implementing such a body in the medium or long term. To stimulate such discussion is the purpose of the remainder of this paper. Moreover, the question needs to be discussed whether there could be a unique format for an IMRSS governing body or various degrees of decentralization oriented, for example, at the physical locations of relevant IMRSS facilities. The main difficulties with solutions that include responsibilities of an international IMRSS body for property, right of use, safeguards, or other issues of a more legal and/or administrative nature are discussed

Differentiation of monkey embryonic stem cells to hepatocytes by feeder-free dispersion culture and expression analyses of cytochrome p450 enzymes responsible for drug metabolism.

Science.gov (United States)

Maruyama, Junya; Matsunaga, Tamihide; Yamaori, Satoshi; Sakamoto, Sakae; Kamada, Noboru; Nakamura, Katsunori; Kikuchi, Shinji; Ohmori, Shigeru

2013-01-01

We reported previously that monkey embryonic stem cells (ESCs) were differentiated into hepatocytes by formation of embryoid bodies (EBs). However, this EB formation method is not always efficient for assays using a large number of samples simultaneously. A dispersion culture system, one of the differentiation methods without EB formation, is able to more efficiently provide a large number of feeder-free undifferentiated cells. A previous study demonstrated the effectiveness of the Rho-associated kinase inhibitor Y-27632 for feeder-free dispersion culture and induction of differentiation of monkey ESCs into neural cells. In the present study, the induction of differentiation of cynomolgus monkey ESCs (cmESCs) into hepatocytes was performed by the dispersion culture method, and the expression and drug inducibility of cytochrome P450 (CYP) enzymes in these hepatocytes were examined. The cmESCs were successfully differentiated into hepatocytes under feeder-free dispersion culture conditions supplemented with Y-27632. The hepatocytes differentiated from cmESCs expressed the mRNAs for three hepatocyte marker genes (α-fetoprotein, albumin, CYP7A1) and several CYP enzymes, as measured by real-time polymerase chain reaction. In particular, the basal expression of cmCYP3A4 (3A8) in these hepatocytes was detected at mRNA and enzyme activity (testosterone 6β-hydroxylation) levels. Furthermore, the expression and activity of cmCYP3A4 (3A8) were significantly upregulated by rifampicin. These results indicated the effectiveness of Y-27632 supplementation for feeder-free dispersed culture and induction of differentiation into hepatocytes, and the expression of functional CYP enzyme(s) in cmESC-derived hepatic cells.

Improvement in ductility of high strength polycrystalline Ni-rich Ni{sub 3}Al alloy produced by EB-PVD

Energy Technology Data Exchange (ETDEWEB)

Sun, J.Y.; Pei, Y.L.; Li, S.S.; Zhang, H.; Gong, S.K., E-mail: gongsk@buaa.edu.cn

2014-11-25

Highlights: • High strength and high ductility of polycrystalline Ni-rich Ni{sub 3}Al alloy sheets were produced. • The elongation could be enhanced from ∼0.5% to ∼14.6% by microstructural control. • The fracture strength (∼820 MPa) was enhanced by the precipitation strengthening. • This work provides a general processing for repairing the worn single crystal blades. - Abstract: A 300 μm Ni-rich Ni{sub 3}Al sheet was produced by electron beam physical vapor deposition (EB-PVD) and followed by different heat treatments to obtain fine γ′/γ two-phase structures with large elongation. Tensile testing was performed at room-temperature, and the corresponding mechanisms were investigated in detail. Results indicated that the as-deposited Ni{sub 3}Al alloy exhibited non-equilibrium directional columnar crystal, and transited to equiaxed crystal with uniformly distributed tough γ phase after heat treatment. Meanwhile, the fracture mechanism transited from brittleness to a mixture of ductility and brittleness modes. With an appropriate heat treatment, high strength (ultimate tensile strength obtained 828 MPa) and high ductility (elongation obtained 14.6%) Ni{sub 3}Al alloy has been achieved, which was due to the mesh network microstructure. A series of transmission electron microscope (TEM) characterizations confirmed that the increasing flow stress of Ni{sub 3}Al alloy was attributed to the cubical secondary γ′ phase precipitates (25–50 nm) within the γ phase. This work provides a potential strategy for repairing the worn tip of single crystal engine blades using Ni-rich Ni{sub 3}Al alloy by EB-PVD.

Editorial: Body Movements

Directory of Open Access Journals (Sweden)

Carina Assuncao

2018-01-01

Full Text Available Today, the juxtaposition between physical bodies and the gameworld is ever more fluid. Virtual Reality headsets are available at game stores with more AAA games being created for the format. The release of the Nintendo Switch and its dynamic JoyCon controllers reintroduce haptic movement based controls.  Pokémon GO’s augmented reality took gamers outdoors and has encouraged the Harry Potter franchise to follow in its mobile footsteps. Each development encourages a step further into the digital world. At the same time, the movement of bodies always has political dimensions. We live in a world where walls seem like solutions to the movement of bodies, while the mere meeting of bodies elsewhere – for sex, marriage and other reasons – is still forbidden by many states’ rules. Games and game-like interfaces have shown the ability to bend those rules, and to sometimes project other worlds and rule systems over our world in order to make bodies move and meet. For this special issue on ‘Body Movements’, Press Start invited authors to focus on embodiment, body movements, political bodies, community bodies, virtual bodies, physical bodies, feminine, masculine, trans- bodies, agency or its lack, and anything else in between. The response to this invitation was variegated, and provocative, as outlined here.

Increased Laforin and Laforin Binding to Glycogen Underlie Lafora Body Formation in Malin-deficient Lafora Disease*

Science.gov (United States)

Tiberia, Erica; Turnbull, Julie; Wang, Tony; Ruggieri, Alessandra; Zhao, Xiao-Chu; Pencea, Nela; Israelian, Johan; Wang, Yin; Ackerley, Cameron A.; Wang, Peixiang; Liu, Yan; Minassian, Berge A.

2012-01-01

The solubility of glycogen, essential to its metabolism, is a property of its shape, a sphere generated through extensive branching during synthesis. Lafora disease (LD) is a severe teenage-onset neurodegenerative epilepsy and results from multiorgan accumulations, termed Lafora bodies (LB), of abnormally structured aggregation-prone and digestion-resistant glycogen. LD is caused by loss-of-function mutations in the EPM2A or EPM2B gene, encoding the interacting laforin phosphatase and malin E3 ubiquitin ligase enzymes, respectively. The substrate and function of malin are unknown; an early counterintuitive observation in cell culture experiments that it targets laforin to proteasomal degradation was not pursued until now. The substrate and function of laforin have recently been elucidated. Laforin dephosphorylates glycogen during synthesis, without which phosphate ions interfere with and distort glycogen construction, leading to LB. We hypothesized that laforin in excess or not removed following its action on glycogen also interferes with glycogen formation. We show in malin-deficient mice that the absence of malin results in massively increased laforin preceding the appearance of LB and that laforin gradually accumulates in glycogen, which corresponds to progressive LB generation. We show that increasing the amounts of laforin in cell culture causes LB formation and that this occurs only with glycogen binding-competent laforin. In summary, malin deficiency causes increased laforin, increased laforin binding to glycogen, and LB formation. Furthermore, increased levels of laforin, when it can bind glycogen, causes LB. We conclude that malin functions to regulate laforin and that malin deficiency at least in part causes LB and LD through increased laforin binding to glycogen. PMID:22669944

Establishing clonal cell lines with endothelial-like potential from CD9(hi, SSEA-1(- cells in embryonic stem cell-derived embryoid bodies.

Directory of Open Access Journals (Sweden)

Qizhou Lian

Full Text Available BACKGROUND: Differentiation of embryonic stem cells (ESCs into specific cell types with minimal risk of teratoma formation could be efficiently directed by first reducing the differentiation potential of ESCs through the generation of clonal, self-renewing lineage-restricted stem cell lines. Efforts to isolate these stem cells are, however, mired in an impasse where the lack of purified lineage-restricted stem cells has hindered the identification of defining markers for these rare stem cells and, in turn, their isolation. METHODOLOGY/PRINCIPAL FINDINGS: We describe here a method for the isolation of clonal lineage-restricted cell lines with endothelial potential from ESCs through a combination of empirical and rational evidence-based methods. Using an empirical protocol that we have previously developed to generate embryo-derived RoSH lines with endothelial potential, we first generated E-RoSH lines from mouse ESC-derived embryoid bodies (EBs. Despite originating from different mouse strains, RoSH and E- RoSH lines have similar gene expression profiles (r(2 = 0.93 while that between E-RoSH and ESCs was 0.83. In silico gene expression analysis predicted that like RoSH cells, E-RoSH cells have an increased propensity to differentiate into vasculature. Unlike their parental ESCs, E-RoSH cells did not form teratomas and differentiate efficiently into endothelial-like cells in vivo and in vitro. Gene expression and FACS analysis revealed that RoSH and E-RoSH cells are CD9(hi, SSEA-1(- while ESCs are CD9(lo, SSEA-1(+. Isolation of CD9(hi, SSEA-1(- cells that constituted 1%-10% of EB-derived cultures generated an E-RoSH-like culture with an identical E-RoSH-like gene expression profile (r(2 = 0.95 and a propensity to differentiate into endothelial-like cells. CONCLUSIONS: By combining empirical and rational evidence-based methods, we identified definitive selectable surface antigens for the isolation and propagation of lineage-restricted stem cells

Glycolytic Enzymes Coalesce in G Bodies under Hypoxic Stress

Directory of Open Access Journals (Sweden)

Meiyan Jin

2017-07-01

Full Text Available Glycolysis is upregulated under conditions such as hypoxia and high energy demand to promote cell proliferation, although the mechanism remains poorly understood. We find that hypoxia in Saccharomyces cerevisiae induces concentration of glycolytic enzymes, including the Pfk2p subunit of the rate-limiting phosphofructokinase, into a single, non-membrane-bound granule termed the “glycolytic body” or “G body.” A yeast kinome screen identifies the yeast ortholog of AMP-activated protein kinase, Snf1p, as necessary for G-body formation. Many G-body components identified by proteomics are required for G-body integrity. Cells incapable of forming G bodies in hypoxia display abnormal cell division and produce inviable daughter cells. Conversely, cells with G bodies show increased glucose consumption and decreased levels of glycolytic intermediates. Importantly, G bodies form in human hepatocarcinoma cells in hypoxia. Together, our results suggest that G body formation is a conserved, adaptive response to increase glycolytic output during hypoxia or tumorigenesis.

Comparative study of P19 EC stem cell differentiation in between conventional hanging drop and the zebrafish chorion as a bio-derived material.

Science.gov (United States)

Dae Seok Na; Lee, Hwang; Sun Uk Kim; Chang Nam Hwang; Sang Ho Lee; Ji Yoon Kang; Jai Kyeong Kim; James Jungho Pak

2008-07-01

Various materials including glass and polymers have been widely used for stem cell culture due to their biocompatibility. However, the roles of these materials are fundamentally limited because they cannot realize or imitate the complex biological functions of living tissues, except in very simple cases. Here, the development of a bio-derived material suitable for stem cell culture and improvement of differentiation efficiency to specific cell lineages with no stimulating agents by using a chorion obtained from a fertilized zebrafish egg through the removal of the yolk and embryonic cell mass from the egg is reported. Mouse P19 EC stem cells introduced into the empty chorion form a uniform embryoid body (EB) without addition of any inducing agent. It is demonstrated that the zebrafish chorion with nanopores improves efficiencies greatly in the EB formation, cell proliferation, and lineage-specific differentiations compared to those of the conventional hanging drop culture method.

Human body as a food for sexuality

Directory of Open Access Journals (Sweden)

Everton Luiz de Oliveira

2017-06-01

Full Text Available The present article depicts a theoretical walk, based on a historical and cultural narrative, that presents the body as a central element in the formatting and construction of human sexuality. Such walk intuits to show some projections, thoughts and materialization which ascertained the physical beauty as a promoter of desires, intentions and erotic feelings, in favor of an announced sexuality and common sense as ideal. The objective was also discuss, how the physical body aesthetic has been the driving force for configuring standard discourses on sexuality, distorting the idea that only the similar bodies to the hegemonic body models can be considered as object of desire, pleasure, and sexual and erotic practices. Finally, it learns that the body can also be admitted as an instrument to subvert the predetermined logic that body, beauty and sexual practices appear to form a triad in favor of the myth of perfect or performative sexuality. As the bodies (all of them has been recognized by the community as promoters of pleasures, desires and foundation for effective practices and sexual/erotic routines, regardless of their physiological, anatomical and aesthetic formatting.

Intralenticular foreign body: a D-Day reminder.

Science.gov (United States)

Dhawahir-Scala, Felipe E; Kamal, A

2005-12-01

Intralenticular foreign bodies are not uncommon after penetrating eye injuries. This is an observational case report where a patient was found to have an embedded lenticular foreign body for more than 60 years. Following such a long period of time the patient has not experienced any significant cataract formation or compromised ocular function due to the foreign body.

Mechanical properties of EB-PVD ZrO2 thermal barrier coatings

International Nuclear Information System (INIS)

Held, Carolin

2014-01-01

In this work, the elastic properties of thermal barrier coatings which were produced by electron-beam enhanced physical vapour deposition were investigated, as well as the dependency of the properties on the sample microstructure, the thermal treatment and the test method. For this purpose, not only commercial coatings were characterized, but also special sample material was used which consists of a 1 mm thick layer of EB-PVD TBC. This material was isothermally heat treated for different times at 950 C, 1100 C and 1200 C and then tested in a specially developed miniaturized bend test and by dynamic mechanical analysis. The sample material was tested by nanoindentation in order to measure the Young's modulus on a local scale, and the porosity of the samples was determined by microstructure analysis and porosimetry. The decrease of porosity could be connected with sintering and subsequent stiffening of the material. The test results are dependent on the tested volume. A small test volume leads to larger measured Young's moduli, while a large test volume yields lower values. The test volume also has an influence on the increase of stiffness during thermal exposure. With a small tested volume, a quicker increase of the Young's modulus was registered, which could be associated to the sintering of local structures.

Collisional Fragmentation Is Not a Barrier to Close-in Planet Formation

Energy Technology Data Exchange (ETDEWEB)

Wallace, Joshua; Tremaine, Scott [Department of Astrophysical Sciences, Princeton University, Princeton, NJ 08544 (United States); Chambers, John, E-mail: joshuajw@princeton.edu [Department of Terrestrial Magnetism, Carnegie Institution for Science, Washington, DC 20015 (United States)

2017-11-01

Collisional fragmentation is shown to not be a barrier to rocky planet formation at small distances from the host star. Simple analytic arguments demonstrate that rocky planet formation via collisions of homogeneous gravity-dominated bodies is possible down to distances of order the Roche radius ( r {sub Roche}). Extensive N -body simulations with initial bodies ≳1700 km that include plausible models for fragmentation and merging of gravity-dominated bodies confirm this conclusion and demonstrate that rocky planet formation is possible down to ∼1.1 r {sub Roche}. At smaller distances, tidal effects cause collisions to be too fragmenting to allow mass buildup to a final, dynamically stable planetary system. We argue that even differentiated bodies can accumulate to form planets at distances that are not much larger than r {sub Roche}.

Thermo-hydro-mechanical processes in the nearfield around a HLW repository in argillaceous formations. Vol. I. Laboratory investigations

Energy Technology Data Exchange (ETDEWEB)

Zhang, Chun-Liang; Czaikowski, Oliver; Rothfuchs, Tilmann; Wieczorek, Klaus

2013-06-15

All over the world, clay formations are being investigated as host medium for geologic disposal of radioactive waste because of their favourable properties, such as very low hydraulic conductivity against fluid transport, good sorption capacity for retardation of radionuclides, and high potential of self-sealing of fractures. The construction of a repository, the disposal of heat-emitting high-level radioactive waste (HLW), the backfilling and sealing of the remaining voids, however, will inevitably induce mechanical (M), hydraulic (H), thermal (T) and chemical (C) disturbances to the host formation and the engineered barrier system (EBS) over very long periods of time during the operation and post-closure phases of the repository. The responses and resulting property changes of the clay host rock and engineered barriers are to be well understood, characterized, and predicted for assessing the long-term performance and safety of the repository.

Microstructure evolution during annealing of TiAl/NiCoCrAl multilayer composite prepared by EB-PVD

Energy Technology Data Exchange (ETDEWEB)

Zhang, Rubing, E-mail: zrb86411680@126.com [Department of Mechanics, School of Civil Engineering, Beijing Jiaotong University, Beijing 100044 (China); Zhang, Deming [Beijing General Research Institute of Mining and Metallurgy, Beijing 100044 (China); Chen, Guiqing [Center for Composite Materials, Harbin Institute of Technology, Harbin 150001 (China); Wang, Yuesheng [Department of Mechanics, School of Civil Engineering, Beijing Jiaotong University, Beijing 100044 (China)

2014-07-01

TiAl/NiCoCrAl laminate composite sheet with a thickness of 0.4–0.6 mm as well as a dimension of 150 mm × 100 mm was fabricated successfully by using electron beam physical vapor deposition (EB-PVD) method. The annealing treatment was processed at 1123 and 1323 K for 3 h in a high vacuum atmosphere, respectively. The phase composition and microstructure of TiAl/NiCoCrAl microlaminated sheet have been analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Based on the sheet characterization and results of the microstructure evolution during annealing treatment process, the diffusion mechanism of interfacial reaction in TiAl/NiCoCrAl microlaminate was investigated and discussed.

The vasa-like gene, olvas, identifies the migration path of primordial germ cells during embryonic body formation stage in the medaka, Oryzias latipes.

Science.gov (United States)

Shinomiya, A; Tanaka, M; Kobayashi, T; Nagahama, Y; Hamaguchi, S

2000-08-01

The medaka homolog of the Drosophila vasa gene, olvas (Oryzias latipes vas) was obtained using polymerase chain reaction of medaka cDNA from the testis and ovary. The spatio-temporal expression pattern of olvas transcripts was observed by in situ hybridization on gonads and embryos. The transcripts for olvas were exclusively detected in the cytoplasm of germ cells in the testis and ovary, not in gonadal somatic cells. In the early developmental stages, each blastomere possessed the maternal transcripts of olvas, which disappeared during gastrula stages. At the late gastrula stage, specific expression of olvas was observed only in germline cells located at the posterior shield. Embryos after the hybridization were examined histologically, and the distribution and migration path of primordial germ cells (PGC) during early stages of embryonic-body formation were revealed using the olvas gene as a germline cell marker. The PGC were translocated from the posterior shield to both sides of the embryonic body via the inner embryonic body in the medaka.

Surface reactivity and hydroxyapatite formation on Ca5MgSi3O12 ceramics in simulated body fluid

Science.gov (United States)

Xu, Jian; Wang, Yaorong; Huang, Yanlin; Cheng, Han; Seo, Hyo Jin

2017-11-01

In this work, the new calcium-magnesium-silicate Ca5MgSi3O12 ceramic was made via traditional solid-state reaction. The bioactivities were investigated by immerging the as-made ceramics in simulated body fluid (SBF) for different time at body temperature (37 °C). Then the samples were taken to measure X-ray powder diffraction (XRD), Scanning electron microscopy (SEM), X-ray energy-dispersive spectra (EDS), and Fourier transform infrared spectroscopy (FT-IR) measurements. The bone-like hydroxyapatite nanoparticles formation was observed on the ceramic surfaces after the immersion in SBF solutions. Ca5MgSi3O12 ceramics possess the Young's modulus and the bending strength and of 96.3 ± 1.2 GPa and 98.7 ± 2.3 MPa, respectively. The data suggest that Ca5MgSi3O12 ceramics can quickly induce HA new layers after soaking in SBF. Ca5MgSi3O12 ceramics are potential to be used as biomaterials for bone-tissue repair. The cell adherence and proliferation experiments are conducted confirming the reliability of the ceramics as a potential candidate.

Characterization and application of automated in-vacuum PIXE/EBS system for direct analysis of chloride and sulfate ions attack in cementitious materials

Science.gov (United States)

Rihawy, M. S.; Alwazzeh, M.; Abbas, K.

2018-01-01

Ion beam analysis (IBA) techniques (Particle Induced X-ray Emission, PIXE and Elastic Backscattering Spectrometry, EBS), were applied to investigate chloride and sulfate ions diffusion into laboratory prepared mortar samples. Development and characterization of an automated in-vacuum macro PIXE/EBS system is thoroughly discussed. Depth profile information of both chloride and sulfate ions in laboratory prepared mortar samples, after immersion in sea water for nine months, was rapidly and easily obtained at fairly low cost and with standardless analysis, demonstrating the value of the application of IBA to elemental depth profiling in cementitious materials. Chloride and sulfate depth profiles were obtained for two sets of mortar samples, one prepared with different water/cement (W/C) ratios and the other with different sand/cement (S/C) ratios. Results showed higher diffusion rates of both chloride and sulfate ions when both ratios are increased. Additionally, the W/C ratio has a stronger influence in both sulfate and chloride penetration than the S/C ratio, and chloride ions penetrate faster than sulfates. Advantages and limitations of applying IBA techniques in this investigation are discussed. The comparison between PIXE and other X-ray based analytical techniques, namely X-ray fluorescence (XRF) and energy and wavelength dispersive X-rays (EDX/WDX), as well as other traditional wet chemical methods is reviewed, and industrial applications are discussed.

C. elegans serine-threonine kinase KIN-29 modulates TGFβ signaling and regulates body size formation

Directory of Open Access Journals (Sweden)

Cohen Stephen

2005-04-01

Full Text Available Background In C. elegans there are two well-defined TGFβ-like signaling pathways. The Sma/Mab pathway affects body size morphogenesis, male tail development and spicule formation while the Daf pathway regulates entry into and exit out of the dauer state. To identify additional factors that modulate TGFβ signaling in the Sma/Mab pathway, we have undertaken a genetic screen for small animals and have identified kin-29. Results kin-29 encodes a protein with a cytoplasmic serine-threonine kinase and a novel C-terminal domain. The kinase domain is a distantly related member of the EMK (ELKL motif kinase family, which interacts with microtubules. We show that the serine-threonine kinase domain has in vitro activity. kin-29 mutations result in small animals, but do not affect male tail morphology as do several of the Sma/Mab signal transducers. Adult worms are smaller than the wild-type, but also develop more slowly. Rescue by kin-29 is achieved by expression in neurons or in the hypodermis. Interaction with the dauer pathway is observed in double mutant combinations, which have been seen with Sma/Mab pathway mutants. We show that kin-29 is epistatic to the ligand dbl-1, and lies upstream of the Sma/Mab pathway target gene, lon-1. Conclusion kin-29 is a new modulator of the Sma/Mab pathway. It functions in neurons and in the hypodermis to regulate body size, but does not affect all TGFβ outputs, such as tail morphogenesis.

Septum formation of the lateral ventricles

International Nuclear Information System (INIS)

Celik, Hakan H.; Aldur, Mustafa M.; Tatar, I.; Tascioglu, A.B.

2005-01-01

In an MRI study examining anomalies of the septum pellucidum in 505 cases, we detected bilateral septum formation of the lateral ventricles in a 17-months-old-baby. In this study, we evaluate 505 (242 males and 263 females) patients referred to the Emaray Imaging Center, Ankara, Turkey with various prediagnoses. We specially selected all the cases from a non-psychotic population. We obtained MRI scans on a 1-Tesla imager (Picker International, Highland Heights, Ohio, USA), with slices of 5 and 6 mm thickness. In the axial and coronal sections, we observed septum formation laterally between the anterior horn and the ventricular body of the lateral ventricles. Radio opaque septum formations started from the caudate nucleus and stretched to the genu of the corpus callosum. There was a second septum formation between the posterior horn and the ventricular body of the right lateral ventricle. It started from the caudate nucleus and stretched to the cavum vergae. (author)

Tuberin and PRAS40 are anti-apoptotic gatekeepers during early human amniotic fluid stem-cell differentiation.

Science.gov (United States)

Fuchs, Christiane; Rosner, Margit; Dolznig, Helmut; Mikula, Mario; Kramer, Nina; Hengstschläger, Markus

2012-03-01

Embryoid bodies (EBs) are three-dimensional multicellular aggregates allowing the in vitro investigation of stem-cell differentiation processes mimicking early embryogenesis. Human amniotic fluid stem (AFS) cells harbor high proliferation potential, do not raise the ethical issues of embryonic stem cells, have a lower risk for tumor development, do not need exogenic induction of pluripotency and are chromosomal stable. Starting from a single human AFS cell, EBs can be formed accompanied by the differentiation into cells of all three embryonic germ layers. Here, we report that siRNA-mediated knockdown of the endogenous tuberous sclerosis complex-2 (TSC2) gene product tuberin or of proline-rich Akt substrate of 40 kDa (PRAS40), the two major negative regulators of mammalian target of rapamycin (mTOR), leads to massive apoptotic cell death during EB development of human AFS cells without affecting the endodermal, mesodermal and ectodermal cell differentiation spectrum. Co-knockdown of endogenous mTOR demonstrated these effects to be mTOR-dependent. Our findings prove this enzyme cascade to be an essential anti-apoptotic gatekeeper of stem-cell differentiation during EB formation. These data allow new insights into the regulation of early stem-cell maintenance and differentiation and identify a new role of the tumor suppressor tuberin and the oncogenic protein PRAS40 with the relevance for a more detailed understanding of the pathogenesis of diseases associated with altered activities of these gene products.

Correlative factors for the location of tracheobronchial foreign bodies in infants and children.

Science.gov (United States)

Xu, Ying; Feng, Rui-Ling; Jiang, Lan; Ren, Hong-Bo; Li, Qi

2018-02-01

This study aims to analyze factors related to the location of tracheobronchial foreign bodies in infants and children, and provide help in the assessment of the disease, surgical risk and prognosis. The clinical data of 1,060 pediatric patients with tracheobronchial foreign bodies diagnosed from January 2015 to December 2015 were retrospectively studied, the association of the location of the foreign bodies with age, gender, granulation formation, chest computed tomography and 3D reconstruction results, preoperative complications, operation time, and hospital stay was analyzed. The location of foreign bodies was not correlated with age, gender, operation time and length of hospital stay, but was correlated to granulation formation, chest computed tomography and 3D reconstruction results, and preoperative complications. The location of foreign bodies was correlated to granulation formation, the location of foreign bodies displayed by chest computed tomography, and preoperative complications.

Laforin prevents stress-induced polyglucosan body formation and Lafora disease progression in neurons.

Science.gov (United States)

Wang, Yin; Ma, Keli; Wang, Peixiang; Baba, Otto; Zhang, Helen; Parent, Jack M; Zheng, Pan; Liu, Yang; Minassian, Berge A; Liu, Yan

2013-08-01

Glycogen, the largest cytosolic macromolecule, is soluble because of intricate construction generating perfect hydrophilic-surfaced spheres. Little is known about neuronal glycogen function and metabolism, though progress is accruing through the neurodegenerative epilepsy Lafora disease (LD) proteins laforin and malin. Neurons in LD exhibit Lafora bodies (LBs), large accumulations of malconstructed insoluble glycogen (polyglucosans). We demonstrated that the laforin-malin complex reduces LBs and protects neuronal cells against endoplasmic reticulum stress-induced apoptosis. We now show that stress induces polyglucosan formation in normal neurons in culture and in the brain. This is mediated by increased glucose-6-phosphate allosterically hyperactivating muscle glycogen synthase (GS1) and is followed by activation of the glycogen digesting enzyme glycogen phosphorylase. In the absence of laforin, stress-induced polyglucosans are undigested and accumulate into massive LBs, and in laforin-deficient mice, stress drastically accelerates LB accumulation and LD. The mechanism through which laforin-malin mediates polyglucosan degradation remains unclear but involves GS1 dephosphorylation by laforin. Our work uncovers the presence of rapid polyglucosan metabolism as part of the normal physiology of neuroprotection. We propose that deficiency in the degradative phase of this metabolism, leading to LB accumulation and resultant seizure predisposition and neurodegeneration, underlies LD.

Effect of Hf Additions to Pt Aluminide Bond Coats on EB-PVD TBC Life

Science.gov (United States)

Nesbitt, James; Nagaraj, Ben; Williams, Jeffrey

2000-01-01

Small Hf additions were incorporated into a Pt aluminide coating during chemical vapor deposition (CVD) on single crystal RENE N5 substrates. Standard yttria-stabilized zirconia top coats were subsequently deposited onto the coated substrates by electron beam-physical vapor deposition (EB-PVD). The coated substrates underwent accelerated thermal cycle testing in a furnace at a temperature in excess of 1121 C (2050 F) (45 minute hot exposure, 15 minute cool to approximately 121 C (250 F)) until the thermal barrier coating (TBC) failed by spallation. Incorporating Hf in the bond coat increased the TBC life by slightly more than three times that of a baseline coating without added Hf. Scanning electron microscopy of the spalled surfaces indicated that the presence of the Hf increased the adherence of the thermally grown alumina to the Pt aluminide bond coat. The presence of oxide pegs growing into the coating from the thermally grown alumina may also partially account for the improved TBC life by creating a near-surface layer with a graded coefficient of thermal expansion.

[Conception and implementation of a novel E-learning module with EbM learning contents in operative dentistry].

Science.gov (United States)

Gerhardt-Szép, Susanne; Dreher, Stefanie; Rüttermann, Stefan; Weberschock, Tobias

2017-11-01

Computer-assisted learning (CAL) programs are becoming more widely used in medical and dental training. However, the combination of CAL programs and evidence-based education in dentistry has not been described previously. The aim was to determine the acceptance and user-friendliness of a CAL program combined with evidence-based training. The didactic concept of the module includes the case-oriented, problem-based embedding of a total of 32 EbM learning assignments, which can be completed interactively and self-determinedly in an interdisciplinary context using focus patients with different diseases. The present study was conducted at the Dental School of the Goethe University in Frankfurt/Main. Data on acceptance and user-friendliness were collected from three consecutive cohorts of 114 dental students attending their first clinical semester. They used the "Toothache Walk-in Clinic: FOCUS" CAL, which can be downloaded via the Internet. The instrument consisted of 64 statements. The first part addressed general information about the user. The second part contained 43 specific statements on the CAL program. These included factors A (handling and technical aspects), B (content and functional range), and C (didactics and suitability for education). Possible responses ranged from 0 to 3 (0 = strongly disagree, 3 = strongly agree). All of the 114 questionnaires distributed were returned (response rate 100%). Most users (90.1%) considered the topics of evidence-based dentistry important for their training. They rated the program by using German school grades, and the overall rating was 2.26 (SD = 0.64). Most students (88.6%) considered the program useful for their clinical training in the treatment of patients. The mean scores for the 43 specific items amounted to 1.90 (factor A, SD = 0.63), 1.55 (factor B, SD = 1.93), and 2.23 (factor C, SD = 0.79). The CAL program with dental medicine vignettes and learning elements for evidence-based medicine received a primarily

Formation of amino acid precursors in the Solar System small bodies using Aluminium-26 as an energy source

Science.gov (United States)

Kebukawa, Yoko; Kobayashi, Kensei; Kawai, Jun; Mita, Hajime; Tachibana, Shogo; Yoda, Isao; Misawa, Shusuke

2016-07-01

Carbonaceous chondrites contain various organic matter including amino acids that may have played an important role for origin of life on the early Earth. The parent bodies of the chondritic meteorites likely formed from silicate dust grains containing some water ice and organic compounds. These planetesimals are known to contain short-lived radio isotopes such as ^{26}Al, and the heat generated from the decay of ^{26}Al was considered to be used for melting ice. The liquid water, for example, changed anhydrous silicates into hydrous silicates, i.e., aqueous alteration. The liquid water would act also as an ideal reaction medium for various organic chemistry. Cody et al. [1] proposed IOM formation via formose reaction starting with formaldehyde and glycolaldehyde during aqueous activity in the small bodies. Additional hydrothermal experiments showed that ammonia enhanced the yields of IOM like organic solids [2]. Formaldehyde and ammonia are ubiquitous in the Solar System and beyond, e.g., comets contain H _{2}CO : NH _{3} : H _{2}O = 0.4-4 : 0.5-1.5 : 100 [3]. Thus these molecules can be expected to have existed in some Solar System small bodies. We study the liquid phase chemistry of the formaldehyde and ammonia, including formations of amino acid precursor molecules, via hydrothermal experiments at isothermal temperatures of 90 °C to 200 °C. We also evaluate the effects of gamma-ray which is released from the decay of ^{26}Al with gamma-ray irradiation experiments using a ^{60}Co gamma-ray source at Tokyo Institute of Technology. Amino acids were detected mostly after acid hydrolysis of heated or irradiated solutions, indicating that most of the amino acids in the products exist as precursors. Some samples contained 'free' amino acids that were detected without acid hydrolysis, but much lower abundance than after acid hydrolysis. Kendrick mass defect (KMD) analyses of High resolution mass spectra obtained using ESI-MS revealed that various CHO and CHNO

Occurrence of epidermolysis bullosa along with Amelogenesis imperfecta in female patient of India

Directory of Open Access Journals (Sweden)

A P Javed

2013-01-01

Full Text Available Epidermolysis bullosa (EB is an inherited disorder, which is characteristically presented as skin blisters developing in response to minor injury. Junctional variety of EB is also associated with enamel hypoplasia. Amelogenesis imperfecta presents with abnormal formation of the enamel both in deciduous and permanent dentition. This article describes a previously unreported case of Amelogenesis imperfecta with complete loss of enamel in a young female patient with EB.

Body Image v kontextu soudobé společnosti

OpenAIRE

Rolínek, Igor

2008-01-01

The thesis focuses on body image - defines the main characteristics of this area, describes cultural influences and body image history and explains basic quantitative values (Body Mass Index, Waist Hip Ratio, Bioelectrical Impedance Analysis). Furthemore the thesis deals with media influence on body ideal formation process, especially in gay subculture. The research part explores recent situation of body image in gay subculture compared with heterosexual males. This section includes the conte...

FAKE STAR FORMATION BURSTS: BLUE HORIZONTAL BRANCH STARS MASQUERADE AS YOUNG MASSIVE STARS IN OPTICAL INTEGRATED LIGHT SPECTROSCOPY

International Nuclear Information System (INIS)

Ocvirk, P.

2010-01-01

Model color-magnitude diagrams of low-metallicity globular clusters (GCs) usually show a deficit of hot evolved stars with respect to observations. We investigate quantitatively the impact of such modeling inaccuracies on the significance of star formation history reconstructions obtained from optical integrated spectra. To do so, we analyze the sample of spectra of galactic globular clusters of Schiavon et al. with STECKMAP (Ocvirk et al.), and the stellar population models of Vazdekis et al. and Bruzual and Charlot, and focus on the reconstructed stellar age distributions. First, we show that background/foreground contamination correlates with E(B - V), which allows us to define a clean subsample of uncontaminated GCs, on the basis of an E(B - V) filtering. We then identify a 'confusion zone' where fake young bursts of star formation pop up in the star formation history although the observed population is genuinely old. These artifacts appear for 70%-100% of cases depending on the population model used, and contribute up to 12% of the light in the optical. Their correlation with the horizontal branch (HB) ratio indicates that the confusion is driven by HB morphology: red HB clusters are well fitted by old stellar population models while those with a blue HB require an additional hot component. The confusion zone extends over [Fe/H] = [ - 2, - 1.2], although we lack the data to probe extreme high and low metallicity regimes. As a consequence, any young starburst superimposed on an old stellar population in this metallicity range could be regarded as a modeling artifact, if it weighs less than 12% of the optical light, and if no emission lines typical of an H II region are present. This work also provides a practical method for constraining HB morphology from high signal to noise integrated light spectroscopy in the optical. This will allow post-asymptotic giant branch evolution studies in a range of environments and at distances where resolving stellar populations

Calculating many-body effects in resonant [(dtμ)d2e] formation

International Nuclear Information System (INIS)

Leon, M.

1986-01-01

A method is developed for calculating the effect of neighboring molecules on the resonant molecular formation reaction tμ + D 2 → [(dtμ)d2e]*, avoiding any expansion in powers of the density. Using a simplified model, the role of collisional broadening, motional narrowing, and the interference of different formation amplitudes is examined. This model is used to generate molecular formation rates as functions of density for fixed temperature. The generalization which will allow comparison with experimental data is discussed

Subacromial bursitis with giant rice bodies as initial presentation of rheumatoid arthritis.

Science.gov (United States)

Subramaniam, Ramesh; Tan, Justina Wei Lyn; Chau, Cora Yuk Ping; Lee, Keng Thiam

2012-10-01

Rice body formation is a nonspecific response to chronic synovial inflammation associated with tuberculous arthritis, rheumatoid arthritis, juvenile rheumatoid arthritis, seronegative inflammatory arthritis, and even osteoarthritis. Such bodies were termed rice bodies because of their close resemblance to grains of polished white rice. We present a case report of a middle-aged woman with right shoulder subacromial/subdeltoid bursitis with giant rice body formation as her initial presentation of rheumatoid arthritis. Her right shoulder symptoms resolved after subacromial and subdeltoid bursectomy and removal of the rice bodies. She subsequently developed inflammatory arthritis of other joints, met the criteria for rheumatoid arthritis, and has been treated medically.

Influence of composition and rate heating on formation of black core in bodies obtained with red ceramic

International Nuclear Information System (INIS)

Santana, L.N.L.; Goncalves, W.P.; Silva, B.J. da; Macedo, R.S.; Santos, R.C.; Lisboa, D.

2011-01-01

In the heating of pieces of red pottery can the defect known as black core, this may deteriorate the technical and aesthetic characteristics of the final product. This study evaluated the influence of chemical composition and heating rate on the formation of black core in bodies red ceramic. The masses were treated and samples were extruded, dried, sintered at 900 °C, with heating rates of 5, 10, 15, 20 and 30 °C / min. and determined the following properties: water absorption, linear shrinkage and flexural strength. The pieces made with the mass containing lower content of iron oxide showed better resistance to bending when subjected to rapid heating. The presence of the black core was identified through visual analysis of the pieces after the break, being more apparent in parts subject to rates above 5 °C / min. (author)

Material design of negative-tone polyphenol resist for EUV and EB lithography

Science.gov (United States)

Kojima, Kyoko; Mori, Shigeki; Shiono, Daiju; Hada, Hideo; Onodera, Junichi

2007-03-01

In order to enable design of a negative-tone polyphenol resist using polarity-change reaction, five resist compounds (3M6C-MBSA-BLs) with different number of functional group of γ-hydroxycarboxyl acid were prepared and evaluated by EB lithography. The resist using mono-protected compound (3M6C-MBSA-BL1a) showed 40-nm hp resolution at an improved dose of 52 μC/cm2 probably due to removal of a non-protected polyphenol while the sensitivity of the resist using a compound of protected ratio of 1.1 on average with distribution of different protected ratio was 72 μC/cm2. For evaluation of the di-protected compound based resist, a di-protected polyphenol was synthesized by a newly developed synthetic route of 3-steps reaction, which is well-suited for mass production. The resist using di-protected compound (3M6C-MBSA-BL2b) also showed 40-nm hp resolution at a dose of 40 μC/cm2, which was faster than that of mono-protected resist. Fundamental EUV lithographic evaluation of the resist using 3M6C-MBSA-BL2b by an EUV open frame exposure tool (EUVES-7000) gave its estimated optimum sensitivity of 7 mJ/cm2 and a proof of fine development behavior without any swelling.

Psammoma bodies - friends or foes of the aging choroid plexus.

Science.gov (United States)

Jovanović, Ivan; Ugrenović, Sladjana; Vasović, Ljiljana; Petrović, Dragan; Cekić, Sonja

2010-06-01

Psammoma bodies are structures classified in the group of dystrophic calcifications, which occur in some kind of tumors and in choroid plexus during the aging process. Despite early discovery of their presence in choroid plexus stroma, mechanisms responsible for their formation remained unclear. Their presence in some kind of tumors was even more extensively studied, but significant breakthrough in the field of their etiology was not attained, too. However, till today correlation between their presence in tumors and aging is not established. Also, there are not any data about structural differences between ones found in tumors and ones found in choroid plexus. This might points to the assumption that besides the aging, some other causes might be involved in their formation in choroid plexus. Furthermore, it is contradictory that forms, like psammoma bodies, present in such malignant formations as tumors, represent quite benign phenomenon in choroid plexus. Literature data and the results of our previous researches revealed that there might be connections between, these, on the first sight quite different processes. Firstly, psammoma bodies are present in stroma of tumors with predominantly papillomatous morphology, which is present in choroid plexus, too. Initial forms of psammoma bodies might be formed in fibrovascular core of choroid plexus villi, similarly like in tumors papillae of papillary thyroid cancer. Their further growth leads to the progressive destruction of both tumors papillae and choroidal villi. Choroid plexus stroma is characterized by the fenestrated blood vessels presence, which are similar to newly formed vessels in tumors. This makes it vulnerable to the noxious agents from circulation. It can contain lymphocytes, macrophages, dendritic cells and myofibroblasts in cases with psammoma bodies, similarly to tumors stroma which is in activated, proinflammatory state. So, all these facts can suggest that similar processes can lead to psammoma

Three familial cases of Pasini variant of dominant dystrophic epidermolysis

Directory of Open Access Journals (Sweden)

Seirafi H

1999-07-01

Full Text Available Epidermolysis bullosa (EB is the term applied to a group of disorders whose common primary feature is the formation of blisters following trivial trauma. Hereditary EB comprises 3 major classes: simplex, junctional and dystrophic, and includes more than 23 phenotypes. The albopapuloid pasini variant of dominant dystrophic EB is characterized by a distinctive clinical appearance. In this article, we report this disease in three members of a family (father and two sons.

Exposure to Barbie: Effects on thin-ideal internalisation, body esteem, and body dissatisfaction among young girls.

Science.gov (United States)

Rice, Karlie; Prichard, Ivanka; Tiggemann, Marika; Slater, Amy

2016-12-01

Barbie doll ownership is high among girls in early primary school. It has been suggested that exposure to Barbie impacts negatively on body image. The present study sought to investigate the effect of exposure to Barbie on young girls' thin-ideal internalisation, body esteem, and body dissatisfaction. Participants were 160 girls (aged 5-8 years) from Adelaide, South Australia. They were randomly allocated one of three Barbie conditions (physical engagement, physical observation, print observation) or to a control toy. Results indicated that exposure to Barbie, irrespective of format, led to higher thin-ideal internalisation than exposure to the control, but had no impact on body esteem or body dissatisfaction. This suggests that interacting with Barbie may encourage girls in early primary school to adopt a preference for a thin body, but with no immediate effect on body image. The long-term impact of Barbie exposure on body image remains unknown. Copyright © 2016 Elsevier Ltd. All rights reserved.

Exchange Bias in Layered GdBaCo2O5.5 Cobaltite

Science.gov (United States)

Solin, N. I.; Naumov, S. V.; Telegin, S. V.; Korolev, A. V.

2017-12-01

It is established that excess oxygen content δ influences the exchange bias (EB) in layered GdBa-Co2O5 + δ cobaltite. The EB effect arises in p-type (δ > 0.5) cobaltite and disappears in n-type (δ training effect inherent in systems with EB has been studied. The results are explained in terms of exchange interaction between the FM and AFM phases. It is assumed that the EB originates from the coexistence of Co3+ and Co4+ ions that leads to the formation of monodomain FM clusters in the AFM matrix of cobaltite.

Arthroscopic treatment of bony loose bodies in the subacromial space

Directory of Open Access Journals (Sweden)

Wei Li

2015-01-01

Conclusion: The mechanism of formation of bony loose bodies is not clear, may be associated with synovial cartilage metaplasia. Arthroscopic removal of loose bodies and bursa debridement is a good option for treatment of the loose body in the subacromial space, which can receive good function.

Multilayer stacks obtained by ion assisted EB PVD aimed at thermal barrier coating

Energy Technology Data Exchange (ETDEWEB)

Roos, E.; Maile, K.; Lyutovich, A. [Stuttgart Univ. (DE). Materialpruefungsanstalt (MPA)

2010-07-01

Thermal Barrier Coating (TBC) using Electron Beam Physical Vapour Deposition (EB PVD) is widely implemented, especially for aero-engine turbine blades. Generally, multilayer stacks are used for these aims. For the additional improvement of intermediate layers with graded transitions to the initial Ni-based alloy, the use of accelerated ions in the EBPVD-process is advantageous. The effect of the substrate bias potential, ion current density and deposition temperature on the structure and properties of Ti and Zr intermediate layers are investigated. The morphology of the films is studied using optical microscopy, scanning electron microscopy (SEM) and atomic force microscopy (AFM). It is found that the surface morphology becomes smoother with rising bias potential and decreasing ion current density. Measurements of Vicker's micro-hardness performed on these coatings have shown its increase with higher values of the bias and its reduction with the growing temperature. This effect is caused by the observed decrease in grain size and higher porosity of the films. A multilayer coating system Ni (based substrate)-Si-Si{sub x}Al{sub y}-Al with graded transitions between the layers is obtained using ion assisted EBPVD. Architecture of a multilayer stack for TBC with graded transitions is proposed. (orig.)

Chondritic Meteorites: Nebular and Parent-Body Formation Processes

Science.gov (United States)

Rubin, Alan E.; Lindstrom, David (Technical Monitor)

2002-01-01

It is important to identify features in chondrites that formed as a result of parent-body modification in order to disentangle nebular and asteroidal processes. However, this task is difficult because unmetamorphosed chondritic meteorites are mixtures of diverse components including various types of chondrules, chondrule fragments, refractory and mafic inclusions, metal-sulfide grains and fine-grained matrix material. Shocked chondrites can contain melt pockets, silicate-darkened material, metal veins, silicate melt veins, and impact-melt-rock clasts. This grant paid for several studies that went far in helping to distinguish primitive nebular features from those produced during asteroidal modification processes.

Recessive Epidermolysis Bullosa simplex- A case report

African Journals Online (AJOL)

Ademu

Abstract: Background:Epidermolysis bullosa simplex (EBS) is characterized by intraepidermal blister formation, most commonly appearing in early infancy. Many variants of EBS exist; the four most common variants are inherited in an autosomal dominant fashion. The recessive forms are rare and less reported in our ...

Adjusting to bodily change following stoma formation: a phenomenological study.

Science.gov (United States)

Thorpe, Gabrielle; Arthur, Antony; McArthur, Maggie

2016-09-01

Scant research has been undertaken to explore in-depth the meaning of bodily change for individuals following stoma formation. The aim of this study was to understand the experience of living with a new stoma, with a focus on bodily change. The study adopted a longitudinal phenomenological approach. Purposeful sampling was used to recruit 12 participants who had undergone faecal stoma-forming surgery. In-depth, unstructured interviews were conducted at 3, 9 and 15 months following surgery. A five-stage framework facilitated iterative data analysis. Stoma formation altered the taken-for-granted relationship individuals had with their bodies in terms of appearance, function and sensation, undermining the unity between body and self. Increasing familiarity with and perceived control over their stoma over time diminished awareness of their changed body, facilitating adaptation and self-acceptance. Stoma formation can undermine an individual's sense of embodied self. A concept of embodiment is proposed to enable the experience of living with a new stoma to be understood as part of a wider process of re-establishing a unity between body, self and world. In defining a framework of care, individuals with a new stoma can be assisted to adapt to and accept a changed sense of embodied self. Implications for Rehabilitation Awareness and understanding of the diverse ways in which stoma formation disrupts the unconscious relationship between body and self can help clinicians to provide responsive, person-centred care. Supporting strategies that facilitate bodily mastery following stoma formation will facilitate rehabilitation and promote adjustment and self-acceptance. A concept of embodiment can help clinicians to deepen their understanding of the experiences of people living with a new stoma and the support they may require during the rehabilitation process. This paper provides clinicians with actionable insight that allows them to better support patients to a smoother

Application of Electron Accelerators in Conjunction with Microwave Sources in Medical Studies

International Nuclear Information System (INIS)

Martin, D.; Craciun, G.; Manaila, E.; Ighigeanu, D.; Margaritescu, I.; Chirita, D.; Neagu, M.

2009-01-01

Electron beams (EB) are presently used, in addition to the routine conventional radiotherapy techniques, for cancer specialized therapies (intensity modulated radiation therapy [1] and total body electron irradiation [2]), the irradiation of blood and blood components, vaccine preparation, and other. Microwaves (MW) are presently used for therapeutic applications in cardiology, urology, surgery, ophthalmology, cancer therapy, and others, and for diagnostic applications such as cancer detection, organ imaging, and more [3]. The reported data show that low dose-all body irradiation with ionizing as well as with nonionizing irradiation may enhance the tumoricidal effects of radiation or chemotherapy, overcome acquired drug resistance and can stimulate certain components of the immune system that may aid in destroying cancer cells. These data suggested that application of low-dose total body EB + MW irradiation in conjunction with chemotherapy could contribute by novel effects to the cancer therapies. In view of this argument two specifically designed radiation exposure devices (REDs) were carried out for separate, successive and simultaneous irradiation with EB of 6.23 MeV and MW of 2.45 GHz in vivo (RED-vivo) and in vitro (RED-vitro) for the following medical studies: 1) The effects of low-dose EB + MW total body irradiation without/with drugs administration on the C57 BL/6 mice bearing malignant melanoma (MM); 2) The effects of separate and simultaneous MW and EB irradiation on MM cells culture without/with drugs incubation and on human blood components (proteins and cells) irradiated in samples of integral blood from healthy donors and from donors with MM. Both REDs consist of the following units: 1) An accelerated EB source: ALIN-10 electron linear accelerator of 6.23 MeV and adjustable absorbed dose rate from 0.002 Gy s-1 up to 70 Gy s-1 (built in the NILPRP, Bucharest, Romania); 2) A special designed exposure chamber that permits inside separate, successive or

Long-lived magnetism on chondrite parent bodies

Science.gov (United States)

Shah, Jay; Bates, Helena C.; Muxworthy, Adrian R.; Hezel, Dominik C.; Russell, Sara S.; Genge, Matthew J.

2017-10-01

We present evidence for both early- and late-stage magnetic activity on the CV and L/LL parent bodies respectively from chondrules in Vigarano and Bjurböle. Using micro-CT scans to re-orientate chondrules to their in-situ positions, we present a new micron-scale protocol for the paleomagnetic conglomerate test. The paleomagnetic conglomerate test determines at 95% confidence, whether clasts within a conglomerate were magnetized before or after agglomeration, i.e., for a chondritic meteorite whether the chondrules carry a pre- or post-accretionary remanent magnetization. We found both meteorites passed the conglomerate test, i.e., the chondrules had randomly orientated magnetizations. Vigarano's heterogeneous magnetization is likely of shock origin, due to the 10 to 20 GPa impacts that brecciated its precursor material on the parent body and transported it to re-accrete as the Vigarano breccia. The magnetization was likely acquired during the break-up of the original body, indicating a CV parent body dynamo was active ∼9 Ma after Solar System formation. Bjurböle's magnetization is due to tetrataenite, which transformed from taenite as the parent body cooled to below 320 °C, when an ambient magnetic field imparted a remanence. We argue either the high intrinsic anisotropy of tetrataenite or brecciation on the parent body manifests as a randomly orientated distribution, and a L/LL parent body dynamo must have been active at least 80 to 140 Ma after peak metamorphism. Primitive chondrites did not originate from entirely primitive, never molten and/or differentiated parent bodies. Primitive chondrite parent bodies consisted of a differentiated interior sustaining a long-lived magnetic dynamo, encrusted by a layer of incrementally accreted primitive meteoritic material. The different ages of carbonaceous and ordinary chondrite parent bodies might indicate a general difference between carbonaceous and ordinary chondrite parent bodies, and/or formation location in the

Cooperation induces other cooperation: Fruiting bodies promote the evolution of macrocysts in Dictyostelium discoideum.

Science.gov (United States)

Shibasaki, Shota; Shirokawa, Yuka; Shimada, Masakazu

2017-05-21

Biological studies of the evolution of cooperation are challenging because this process is vulnerable to cheating. Many mechanisms, including kin discrimination, spatial structure, or by-products of self-interested behaviors, can explain this evolution. Here we propose that the evolution of cooperation can be induced by other cooperation. To test this idea, we used a model organism Dictyostelium discoideum because it exhibits two cooperative dormant phases, the fruiting body and the macrocyst. In both phases, the same chemoattractant, cyclic AMP (cAMP), is used to collect cells. This common feature led us to hypothesize that the evolution of macrocyst formation would be induced by coexistence with fruiting bodies. Before forming a mathematical model, we confirmed that macrocysts coexisted with fruiting bodies, at least under laboratory conditions. Next, we analyzed our evolutionary game theory-based model to investigate whether coexistence with fruiting bodies would stabilize macrocyst formation. The model suggests that macrocyst formation represents an evolutionarily stable strategy and a global invader strategy under this coexistence, but is unstable if the model ignores the fruiting body formation. This result indicates that the evolution of macrocyst formation and maintenance is attributable to coexistence with fruiting bodies. Therefore, macrocyst evolution can be considered as an example of evolution of cooperation induced by other cooperation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Distinct retroelement classes define evolutionary breakpoints demarcating sites of evolutionary novelty

Science.gov (United States)

Longo, Mark S; Carone, Dawn M; Green, Eric D; O'Neill, Michael J; O'Neill, Rachel J

2009-01-01

Background Large-scale genome rearrangements brought about by chromosome breaks underlie numerous inherited diseases, initiate or promote many cancers and are also associated with karyotype diversification during species evolution. Recent research has shown that these breakpoints are nonrandomly distributed throughout the mammalian genome and many, termed "evolutionary breakpoints" (EB), are specific genomic locations that are "reused" during karyotypic evolution. When the phylogenetic trajectory of orthologous chromosome segments is considered, many of these EB are coincident with ancient centromere activity as well as new centromere formation. While EB have been characterized as repeat-rich regions, it has not been determined whether specific sequences have been retained during evolution that would indicate previous centromere activity or a propensity for new centromere formation. Likewise, the conservation of specific sequence motifs or classes at EBs among divergent mammalian taxa has not been determined. Results To define conserved sequence features of EBs associated with centromere evolution, we performed comparative sequence analysis of more than 4.8 Mb within the tammar wallaby, Macropus eugenii, derived from centromeric regions (CEN), euchromatic regions (EU), and an evolutionary breakpoint (EB) that has undergone convergent breakpoint reuse and past centromere activity in marsupials. We found a dramatic enrichment for long interspersed nucleotide elements (LINE1s) and endogenous retroviruses (ERVs) and a depletion of short interspersed nucleotide elements (SINEs) shared between CEN and EBs. We analyzed the orthologous human EB (14q32.33), known to be associated with translocations in many cancers including multiple myelomas and plasma cell leukemias, and found a conserved distribution of similar repetitive elements. Conclusion Our data indicate that EBs tracked within the class Mammalia harbor sequence features retained since the divergence of marsupials

Distinct retroelement classes define evolutionary breakpoints demarcating sites of evolutionary novelty

Directory of Open Access Journals (Sweden)

Green Eric D

2009-07-01

Full Text Available Abstract Background Large-scale genome rearrangements brought about by chromosome breaks underlie numerous inherited diseases, initiate or promote many cancers and are also associated with karyotype diversification during species evolution. Recent research has shown that these breakpoints are nonrandomly distributed throughout the mammalian genome and many, termed "evolutionary breakpoints" (EB, are specific genomic locations that are "reused" during karyotypic evolution. When the phylogenetic trajectory of orthologous chromosome segments is considered, many of these EB are coincident with ancient centromere activity as well as new centromere formation. While EB have been characterized as repeat-rich regions, it has not been determined whether specific sequences have been retained during evolution that would indicate previous centromere activity or a propensity for new centromere formation. Likewise, the conservation of specific sequence motifs or classes at EBs among divergent mammalian taxa has not been determined. Results To define conserved sequence features of EBs associated with centromere evolution, we performed comparative sequence analysis of more than 4.8 Mb within the tammar wallaby, Macropus eugenii, derived from centromeric regions (CEN, euchromatic regions (EU, and an evolutionary breakpoint (EB that has undergone convergent breakpoint reuse and past centromere activity in marsupials. We found a dramatic enrichment for long interspersed nucleotide elements (LINE1s and endogenous retroviruses (ERVs and a depletion of short interspersed nucleotide elements (SINEs shared between CEN and EBs. We analyzed the orthologous human EB (14q32.33, known to be associated with translocations in many cancers including multiple myelomas and plasma cell leukemias, and found a conserved distribution of similar repetitive elements. Conclusion Our data indicate that EBs tracked within the class Mammalia harbor sequence features retained since the

Enrichment of cardiac differentiation of mouse embryonic stem cells by optimizing the hanging drop method.

Science.gov (United States)

Chen, Ming; Lin, Yong-Qing; Xie, Shuang-Lun; Wu, Hong-Fu; Wang, Jing-Feng

2011-04-01

Hanging drop (HD) culture is used to induce differentiation of embryonic stem cells (ESCs) into other cell types including cardiomyocytes. However, the factors affecting cardiac differentiation of ESCs with this method remain incompletely understood. We have investigated the effects of the starting number of ESCs in embryoid bodies (EBs) and the time of EB adherence to gelatin-coated plates on cardiac differentiation: cardiac differentiation was increased in the EBs by a larger number of ESCs and was decreased by plating EBs at day 4 or earlier. These two factors can thus be optimized to enrich the cardiac differentiation in ESCs using the HD method.

MAGNETIC FLUX CANCELLATION IN ELLERMAN BOMBS

Energy Technology Data Exchange (ETDEWEB)

Reid, A.; Mathioudakis, M.; Nelson, C. J.; Henriques, V. [Astrophysics Research Centre, School of Mathematics and Physics, Queen’s University Belfast, BT7 1NN, Northern Ireland (United Kingdom); Doyle, J. G. [Armagh Observatory, College Hill, Armagh, BT61 9DG (United Kingdom); Scullion, E. [Trinity College Dublin, College Green, Dublin 2 (Ireland); Ray, T., E-mail: areid29@qub.ac.uk [Dublin Institute for Advanced Studies, 31 Fitzwilliam Place, Dublin 2 (Ireland)

2016-06-01

Ellerman Bombs (EBs) are often found to be co-spatial with bipolar photospheric magnetic fields. We use H α imaging spectroscopy along with Fe i 6302.5 Å spectropolarimetry from the Swedish 1 m Solar Telescope (SST), combined with data from the Solar Dynamic Observatory , to study EBs and the evolution of the local magnetic fields at EB locations. EBs are found via an EB detection and tracking algorithm. Using NICOLE inversions of the spectropolarimetric data, we find that, on average, (3.43 ± 0.49) × 10{sup 24} erg of stored magnetic energy disappears from the bipolar region during EB burning. The inversions also show flux cancellation rates of 10{sup 14}–10{sup 15} Mx s{sup −1} and temperature enhancements of 200 K at the detection footpoints. We investigate the near-simultaneous flaring of EBs due to co-temporal flux emergence from a sunspot, which shows a decrease in transverse velocity when interacting with an existing, stationary area of opposite polarity magnetic flux, resulting in the formation of the EBs. We also show that these EBs can be fueled further by additional, faster moving, negative magnetic flux regions.

Formation of active inclusion bodies induced by hydrophobic self-assembling peptide GFIL8.

Science.gov (United States)

Wang, Xu; Zhou, Bihong; Hu, Weike; Zhao, Qing; Lin, Zhanglin

2015-06-16

In the last few decades, several groups have observed that proteins expressed as inclusion bodies (IBs) in bacteria could still be biologically active when terminally fused to an appropriate aggregation-prone partner such as pyruvate oxidase from Paenibacillus polymyxa (PoxB). More recently, we have demonstrated that three amphipathic self-assembling peptides, an alpha helical peptide 18A, a beta-strand peptide ELK16, and a surfactant-like peptide L6KD, have properties that induce target proteins into active IBs. We have developed an efficient protein expression and purification approach for these active IBs by introducing a self-cleavable intein molecule. In this study, the self-assembling peptide GFIL8 (GFILGFIL) with only hydrophobic residues was analyzed, and this peptide effectively induced the formation of cytoplasmic IBs in Escherichia coli when terminally attached to lipase A and amadoriase II. The protein aggregates in cells were confirmed by transmission electron microscopy analysis and retained ~50% of their specific activities relative to the native counterparts. We constructed an expression and separation coupled tag (ESCT) by incorporating an intein molecule, the Mxe GyrA intein. Soluble target proteins were successfully released from active IBs upon cleavage of the intein between the GFIL8 tag and the target protein, which was mediated by dithiothreitol. A variant of GFIL8, GFIL16 (GFILGFILGFILGFIL), improved the ESCT scheme by efficiently eliminating interference from the soluble intein-GFIL8 molecule. The yields of target proteins at the laboratory scale were 3.0-7.5 μg/mg wet cell pellet, which is comparable to the yields from similar ESCT constructs using 18A, ELK16, or the elastin-like peptide tag scheme. The all-hydrophobic self-assembling peptide GFIL8 induced the formation of active IBs in E. coli when terminally attached to target proteins. GFIL8 and its variant GFIL16 can act as a "pull-down" tag to produce purified soluble proteins with

Derivation of Stromal (Skeletal and Mesenchymal) Stem-Like Cells from Human Embryonic Stem Cells

Science.gov (United States)

Harkness, Linda; Abdallah, Basem M.; Elsafadi, Mona; Al-Nbaheen, May S.; Aldahmash, Abdullah; Kassem, Moustapha

2012-01-01

Derivation of bone forming cells (osteoblasts) from human embryonic stem cells (hESCs) is a prerequisite for their use in clinical applications. However, there is no standard protocol for differentiating hESCs into osteoblastic cells. The aim of this study was to identify the emergence of a human stromal (mesenchymal and skeletal) stem cell (hMSC)-like population, known to be osteoblastic cell precursors and to test their osteoblastic differentiation capacity in ex vivo cultures and in vivo. We cultured hESCs in a feeder-free environment using serum replacement and as suspension aggregates (embryoid bodies; hEBs). Over a 20 day developmental period, the hEBs demonstrated increasing enrichment for cells expressing hMSC markers: CD29, CD44, CD63, CD56, CD71, CD73, CD105, CD106, and CD166 as revealed by immunohistochemical staining and flow cytometry (fluorescence-activated cell sorting) analysis. Ex vivo differentiation of hEBs using bone morphogenic protein 2 (BMP2) combined with standard osteoblast induction medium led to weak osteoblastic induction. Conversely, subcutaneous in vivo implantation of day 20 hEBs in immune deficient mice, mixed with hydroxyapatite/tricalcium phosphate (HA/TCP) as an osteoconductive scaffold, revealed bone and cartilage, and fibrous tissue elements after 8 weeks. These tissues were of human origin and there was no evidence of differentiation to nonmesodermal tissues. hEBs implanted in the absence of HA/TCP formed vacuolated tissue containing glandular, fibrous and muscle-like tissue elements. Conversely, implantation of undifferentiated hESCs resulted in the formation of a teratoma containing a mixture of endodermal, mesodermal, and ectodermal tissues. Our study demonstrates that hMSC-like cells can be obtained from hESCs and they can be induced to form skeletal tissues in vivo when combined with HA/TCP. These findings are relevant for tissue engineering and suggest that differentiated hEBs can provide an unlimited source for

Inclusion bodies are a site of ebolavirus replication.

Science.gov (United States)

Hoenen, Thomas; Shabman, Reed S; Groseth, Allison; Herwig, Astrid; Weber, Michaela; Schudt, Gordian; Dolnik, Olga; Basler, Christopher F; Becker, Stephan; Feldmann, Heinz

2012-11-01

Inclusion bodies are a characteristic feature of ebolavirus infections in cells. They contain large numbers of preformed nucleocapsids, but their biological significance has been debated, and they have been suggested to be aggregates of viral proteins without any further biological function. However, recent data for other viruses that produce similar structures have suggested that inclusion bodies might be involved in genome replication and transcription. In order to study filovirus inclusion bodies, we fused mCherry to the ebolavirus polymerase L, which is found in inclusion bodies. The resulting L-mCherry fusion protein was functional in minigenome assays and incorporated into virus-like particles. Importantly, L-mCherry fluorescence in transfected cells was readily detectable and distributed in a punctate pattern characteristic for inclusion bodies. A recombinant ebolavirus encoding L-mCherry instead of L was rescued and showed virtually identical growth kinetics and endpoint titers to those for wild-type virus. Using this virus, we showed that the onset of inclusion body formation corresponds to the onset of viral genome replication, but that viral transcription occurs prior to inclusion body formation. Live-cell imaging further showed that inclusion bodies are highly dynamic structures and that they can undergo dramatic reorganization during cell division. Finally, by labeling nascent RNAs using click technology we showed that inclusion bodies are indeed the site of viral RNA synthesis. Based on these data we conclude that, rather than being inert aggregates of nucleocapsids, ebolavirus inclusion bodies are in fact complex and dynamic structures and an important site at which viral RNA replication takes place.

Terrestrial planet formation in a protoplanetary disk with a local mass depletion: A successful scenario for the formation of Mars

Energy Technology Data Exchange (ETDEWEB)

Izidoro, A.; Winter, O. C. [UNESP, Univ. Estadual Paulista - Grupo de Dinâmica Orbital and Planetologia, Guaratinguetá, CEP 12.516-410, São Paulo (Brazil); Haghighipour, N. [Institute for Astronomy and NASA Astrobiology Institute, University of Hawaii-Manoa, Honolulu, HI 96822 (United States); Tsuchida, M., E-mail: izidoro@feg.unesp.br, E-mail: nader@ifa.hawaii.edu [UNESP, Univ. Estadual Paulista, DCCE-IBILCE, São José do Rio Preto, CEP 15.054-000, São Paulo (Brazil)

2014-02-10

Models of terrestrial planet formation for our solar system have been successful in producing planets with masses and orbits similar to those of Venus and Earth. However, these models have generally failed to produce Mars-sized objects around 1.5 AU. The body that is usually formed around Mars' semimajor axis is, in general, much more massive than Mars. Only when Jupiter and Saturn are assumed to have initially very eccentric orbits (e ∼ 0.1), which seems fairly unlikely for the solar system, or alternately, if the protoplanetary disk is truncated at 1.0 AU, simulations have been able to produce Mars-like bodies in the correct location. In this paper, we examine an alternative scenario for the formation of Mars in which a local depletion in the density of the protosolar nebula results in a non-uniform formation of planetary embryos and ultimately the formation of Mars-sized planets around 1.5 AU. We have carried out extensive numerical simulations of the formation of terrestrial planets in such a disk for different scales of the local density depletion, and for different orbital configurations of the giant planets. Our simulations point to the possibility of the formation of Mars-sized bodies around 1.5 AU, specifically when the scale of the disk local mass-depletion is moderately high (50%-75%) and Jupiter and Saturn are initially in their current orbits. In these systems, Mars-analogs are formed from the protoplanetary materials that originate in the regions of disk interior or exterior to the local mass-depletion. Results also indicate that Earth-sized planets can form around 1 AU with a substantial amount of water accreted via primitive water-rich planetesimals and planetary embryos. We present the results of our study and discuss their implications for the formation of terrestrial planets in our solar system.

Small Bodies, Big Discoveries: NASA's Small Bodies Education Program

Science.gov (United States)

Mayo, L.; Erickson, K. J.

2014-12-01

2014 is turning out to be a watershed year for celestial events involving the solar system's unsung heroes, small bodies. This includes the close flyby of comet C/2013 A1 / Siding Spring with Mars in October and the historic Rosetta mission with its Philae lander to comet 67P/Churyumov-Gerasimenko. Beyond 2014, the much anticipated 2015 Pluto flyby by New Horizons and the February Dawn Mission arrival at Ceres will take center stage. To deliver the excitement and wonder of our solar system's small bodies to worldwide audiences, NASA's JPL and GSFC education teams in partnership with NASA EDGE will reach out to the public through multiple venues including broadcast media, social media, science and math focused educational activities, observing challenges, interactive visualization tools like "Eyes on the Solar System" and more. This talk will highlight NASA's focused education effort to engage the public in small bodies mission science and the role these objects play in our understanding of the formation and evolution of the solar system.

Small solar system bodies as granular systems

Science.gov (United States)

Hestroffer, Daniel; Campo Bagatín, Adriano; Losert, Wolfgang; Opsomer, Eric; Sánchez, Paul; Scheeres, Daniel J.; Staron, Lydie; Taberlet, Nicolas; Yano, Hajime; Eggl, Siegfried; Lecomte, Charles-Edouard; Murdoch, Naomi; Radjai, Fahrang; Richardson, Derek C.; Salazar, Marcos; Schwartz, Stephen R.; Tanga, Paolo

2017-06-01

Asteroids and other Small Solar System Bodies (SSSBs) are currently of great scientific and even industrial interest. Asteroids exist as the permanent record of the formation of the Solar System and therefore hold many clues to its understanding as a whole, as well as insights into the formation of planetary bodies. Additionally, SSSBs are being investigated in the context of impact risks for the Earth, space situational awareness and their possible industrial exploitation (asteroid mining). In all these aspects, the knowledge of the geophysical characteristics of SSSB surface and internal structure are of great importance. Given their size, constitution, and the evidence that many SSSBs are not simple monoliths, these bodies should be studied and modelled as self-gravitating granular systems in general, or as granular systems in micro-gravity environments in particular contexts. As such, the study of the geophysical characteristics of SSSBs is a multi-disciplinary effort that lies at the crossroads between Granular Mechanics, Celestial Mechanics, Soil Mechanics, Aerospace Engineering and Computer Sciences.

Visualizing astrophysical N-body systems

International Nuclear Information System (INIS)

Dubinski, John

2008-01-01

I begin with a brief history of N-body simulation and visualization and then go on to describe various methods for creating images and animations of modern simulations in cosmology and galactic dynamics. These techniques are incorporated into a specialized particle visualization software library called MYRIAD that is designed to render images within large parallel N-body simulations as they run. I present several case studies that explore the application of these methods to animations in star clusters, interacting galaxies and cosmological structure formation.

Identification of the IGF-1 processing product human Ec/rodent Eb peptide in various tissues: Evidence for its differential regulation after exercise-induced muscle damage in humans.

Science.gov (United States)

Vassilakos, George; Philippou, Anastassios; Koutsilieris, Michael

2017-02-01

Insulin-like growth factor-1 (IGF-1) is a pleiotropic factor expressed in various tissues and plays a critical role in skeletal muscle physiology. Alternative splicing of the IGF-1 gene gives rise to different precursor polypeptides (isoforms) which could undergo post-translational cleavage, generating the common mature IGF-1 peptide and different carboxyl terminal extension (E-) peptides, with the fate of the latter being, so far, unknown. The objective if this study was to identify the IGF-1Ec forms or processing product(s), other than mature IGF-1, generated in different human and rodent tissues and particularly in human skeletal muscle after exercise-induced damage. Protein lysates from a wide range of human and rodent tissues were immunoblotted with a rabbit anti-human Ec polyclonal antibody raised against the last 24 amino acids of the C-terminal of the Ec peptide. This antibody can recognize the Ec peptide, both as part of IGF-1Ec and alone, and also the corresponding rodent forms, due to the high homology that the human Ec shares with the rodent Eb. We were able to confirm, for the first time, that the human Ec peptide and its rodent homologous Eb peptide are produced simultaneously with their precursor protein (pro-IGF-1Ec/Eb) in vivo, in a wide range of tissues (e.g. muscle, liver, heart). Proprotein convertase furin digestion of human muscle and liver protein lysates confirmed that the higher molecular form, pro-IGF-1Ec, can be cleaved to produce the free Ec peptide. Furthermore, initial evidence is provided that Ec peptide is differentially regulated during the process of muscle regeneration after exercise-induced damage in humans. The findings of this study possibly imply that the post-translational modification of the IGF-1Ec pro-peptide may regulate the bioavailability and activity of the processing product(s). Copyright © 2016. Published by Elsevier Ltd.

GW-Bodies and P-Bodies Constitute Two Separate Pools of Sequestered Non-Translating RNAs.

Directory of Open Access Journals (Sweden)

Prajal H Patel

Full Text Available Non-translating RNAs that have undergone active translational repression are culled from the cytoplasm into P-bodies for decapping-dependent decay or for sequestration. Organisms that use microRNA-mediated RNA silencing have an additional pathway to remove RNAs from active translation. Consequently, proteins that govern microRNA-mediated silencing, such as GW182/Gw and AGO1, are often associated with the P-bodies of higher eukaryotic organisms. Due to the presence of Gw, these structures have been referred to as GW-bodies. However, several reports have indicated that GW-bodies have different dynamics to P-bodies. Here, we use live imaging to examine GW-body and P-body dynamics in the early Drosophila melanogaster embryo. While P-bodies are present throughout early embryonic development, cytoplasmic GW-bodies only form in significant numbers at the midblastula transition. Unlike P-bodies, which are predominantly cytoplasmic, GW-bodies are present in both nuclei and the cytoplasm. RNA decapping factors such as DCP1, Me31B, and Hpat are not associated with GW-bodies, indicating that P-bodies and GW-bodies are distinct structures. Furthermore, known Gw interactors such as AGO1 and the CCR4-NOT deadenylation complex, which have been shown to be important for Gw function, are also not present in GW-bodies. Use of translational inhibitors puromycin and cycloheximide, which respectively increase or decrease cellular pools of non-translating RNAs, alter GW-body size, underscoring that GW-bodies are composed of non-translating RNAs. Taken together, these data indicate that active translational silencing most likely does not occur in GW-bodies. Instead GW-bodies most likely function as repositories for translationally silenced RNAs. Finally, inhibition of zygotic gene transcription is unable to block the formation of either P-bodies or GW-bodies in the early embryo, suggesting that these structures are composed of maternal RNAs.

Multiple and fast: The accretion of ordinary chondrite parent bodies

International Nuclear Information System (INIS)

Vernazza, P.; Barge, P.; Zanda, B.; Hewins, R.; Binzel, R. P.; DeMeo, F. E.; Lockhart, M.; Hiroi, T.; Birlan, M.; Ricci, L.

2014-01-01

Although petrologic, chemical, and isotopic studies of ordinary chondrites and meteorites in general have largely helped establish a chronology of the earliest events of planetesimal formation and their evolution, there are several questions that cannot be resolved via laboratory measurements and/or experiments alone. Here, we propose the rationale for several new constraints on the formation and evolution of ordinary chondrite parent bodies (and, by extension, most planetesimals) from newly available spectral measurements and mineralogical analysis of main-belt S-type asteroids (83 objects) and unequilibrated ordinary chondrite meteorites (53 samples). Based on the latter, we suggest that spectral data may be used to distinguish whether an ordinary chondrite was formed near the surface or in the interior of its parent body. If these constraints are correct, the suggested implications include that: (1) large groups of compositionally similar asteroids are a natural outcome of planetesimal formation and, consequently, meteorites within a given class can originate from multiple parent bodies; (2) the surfaces of large (up to ∼200 km) S-type main-belt asteroids mostly expose the interiors of the primordial bodies, a likely consequence of impacts by small asteroids (D < 10 km) in the early solar system; (3) the duration of accretion of the H chondrite parent bodies was likely short (instantaneous or in less than ∼10 5 yr, but certainly not as long as 1 Myr); (4) LL-like bodies formed closer to the Sun than H-like bodies, a possible consequence of the radial mixing and size sorting of chondrules in the protoplanetary disk prior to accretion.

Impact-Basin Formation on Mercury: Current Observations and Outstanding Questions

Science.gov (United States)

Baker, D. M. H.; Head, J. W.; Fassett, C. I.

2018-05-01

Mercury provides an important laboratory for understanding impact-basin formation on planetary bodies. MESSENGER observations improved our understanding, but much is still unknown about the formation and evolution of basin features.

Experimental Studies of Engineered Barrier Systems Conducted at Los Alamos National Laboratory (FY16)

Energy Technology Data Exchange (ETDEWEB)

Caporuscio, Florie Andre [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Norskog, Katherine Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Maner, James [Univ. of Oklahoma, Norman, OK (United States). School of Geology and Geophysics; Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Palaich, Sarah [Univ. of California, Los Angeles, CA (United States). Dept. of Earth, Planetary, and Space Sciences; Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Cheshire, Michael C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-08-04

Over the past five years the Used Fuel Campaign has investigated Engineered Barrier Systems (EBS) at higher heat loads (up to 300°C) and pressure (150 bar). This past year experimental work was hindered due to a revamping of the hydrothermal lab. Regardless, two experiments were run this past year, EBS-18 and EBS-19. EBS-18 was run using Low Carbon Steel (LCS) and opalinus clay in addition to the bentonite and opalinus brine. Many of the past results were confirmed in EBS-18, such as the restriction of illite formation due to the bulk chemistry, pyrite degradation, and zeolite formation dependent on the bentonite and opalinus clay. The LCS show vast amounts of pit corrosion (over 100μm of corrosion in six weeks), leading a corrosion rate of 1083 μm/year. In addition, a mineral goethite, an iron-bearing hydroxide, formed in the pits of the LCS. Preliminary results from EBS-19 water chemistry are included but SEM imaging, micro probe and XRD are still needed for further results. Copper corrosion was investigated further and over 850 measurements were taken. It was concluded that pitting and pyrite degradation drastically increase the corrosion rate from 0.12 to 0.39 μm/day. However, the growth of a layer of the mineral chalcocite is thought to subdue the corrosion rate to 0.024 μm/day as observed in the EBS-13, a sixth month experiment. This document presents the findings of this past year.

Dynamic recruitment of active proteasomes into polyglutamine initiated inclusion bodies

NARCIS (Netherlands)

Schipper-Krom, Sabine; Juenemann, Katrin; Jansen, Anne H.; Wiemhoefer, Anne; van den Nieuwendijk, Rianne; Smith, Donna L.; Hink, Mark A.; Bates, Gillian P.; Overkleeft, Hermen; Ovaa, Huib; Reits, Eric

2014-01-01

Neurodegenerative disorders such as Huntington's disease are hallmarked by neuronal intracellular inclusion body formation. Whether proteasomes are irreversibly recruited into inclusion bodies in these protein misfolding disorders is a controversial subject. In addition, it has been proposed that

Endwall convective heat transfer for bluff bodies

DEFF Research Database (Denmark)

Wang, Lei; Salewski, Mirko; Sundén, Bengt

2012-01-01

The endwall heat transfer characteristics of forced flow past bluff bodies have been investigated using liquid crystal thermography (LCT). The bluff body is placed in a rectangular channel with both its ends attached to the endwalls. The Reynolds number varies from 50,000 to 100,000. In this study......, a single bluff body and two bluff bodies arranged in tandem are considered. Due to the formation of horseshoe vortices, the heat transfer is enhanced appreciably for both cases. However, for the case of two bluff bodies in tandem, it is found that the presence of the second bluff body decreases the heat...... transfer as compared to the case of a single bluff body. In addition, the results show that the heat transfer exhibits Reynolds number similarity. For a single bluff body, the Nusselt number profiles collapse well when the data are scaled by Re0.55; for two bluff bodies arranged in tandem, the heat...

High temperature oxidation behavior of hafnium modified NiAl bond coat in EB-PVD thermal barrier coating system

Energy Technology Data Exchange (ETDEWEB)

Guo Hongbo; Sun Lidong; Li Hefei [Department of Material Science and Engineering, Beijing University of Aeronautics and Astronautics, No.37 Xueyuan Road, Beijing 100083 (China); Gong Shengkai [Department of Material Science and Engineering, Beijing University of Aeronautics and Astronautics, No.37 Xueyuan Road, Beijing 100083 (China)], E-mail: gongsk@buaa.edu.cn

2008-06-30

NiAl coatings doped with 0.5 at.% and 1.5 at.% Hf were produced by co-evaporation of NiAl and Hf ingots by electron beam physical vapor deposition (EB-PVD), respectively. The addition of 0.5 at.% Hf significantly improved the cyclic oxidation resistance of the NiAl coating. The TGO layer in the 1.5 at.% Hf doped NiAl coating is straight; while that in the 0.5 at.% Hf doped coating became undulated after thermal cycling. The doped NiAl thermal barrier coatings (TBCs) revealed improved thermal cycling lifetimes at 1423 K, compared to the undoped TBC. Failure of the 0.5 at.% Hf doped TBC occurred by cracking at the interface between YSZ topcoat and bond coat, while the 1.5 at.% Hf doped TBC cracked at the interface between bond coat and substrate.

Robust formation control of marine surface craft using Lagrange multipliers

DEFF Research Database (Denmark)

Ihle, Ivar-Andre F.; Jouffroy, Jerome; Fossen, Thor I.

2006-01-01

This paper presents a formation modelling scheme based on a set of inter-body constraint functions and Lagrangian multipliers. Formation control for a °eet of marine craft is achieved by stabilizing the auxiliary constraints such that the desired formation con¯guration appears. In the proposed fr...

New method for determination of star formation history

OpenAIRE

Čeponis, Marius

2017-01-01

A New Method for Determination of Star Formation History Without stars there would not be any life and us. Almost all elements in our bodies are made in stars. Yet we still don‘t fully understand all the processes governing formation and evolution of stellar systems. Their star formation histories really help in trying to understand these processes. In this work a new Bayesian method for determination of star formation history is proposed. This method uses photometric data of resolved stars a...

Formation of the satellites of the outer solar system - Sources of their atmospheres

International Nuclear Information System (INIS)

Coradini, A.; Cerroni, P.; Magni, G.; Federico, C.

1989-01-01

The present account of the current understanding of regular satellite systems' origins gives attention to the essential processes leading to current satellite configurations, proceeding on the concept that the presence of atmospheres is connected with the final phases of satellite formation. Four major formation stages are envisioned: (1) the disk phase, linking the formation of the primary body to that of the satellites; (2) the formation phase of intermediate-sized bodies; (3) the collisional evolution of planatesimals; and (4) a series of evolutionary phases linking the primordial phases to currently observed states, in which the internal composition and thermal history of the satellites are key factors in satellite atmosphere formation

Resolved star formation on sub-galactic scales in a merger at z = 1.7

International Nuclear Information System (INIS)

Whitaker, Katherine E.; Rigby, Jane R.; Teng, Stacy H.; Brammer, Gabriel B.; Gladders, Michael D.; Sharon, Keren; Wuyts, Eva

2014-01-01

We present a detailed analysis of Hubble Space Telescope (HST) Wide Field Camera 3 (WFC3) G141 grism spectroscopy for seven star-forming regions of the highly magnified lensed starburst galaxy RCSGA 032727-132609 at z = 1.704. We measure the spatial variations of the extinction in RCS0327 through the observed Hγ/Hβ emission line ratios, finding a constant average extinction of E(B – V) gas = 0.40 ± 0.07. We infer that the star formation is enhanced as a result of an ongoing interaction, with measured star formation rates derived from demagnified, extinction-corrected Hβ line fluxes for the individual star-forming clumps falling >1-2 dex above the star formation sequence. When combining the HST/WFC3 [O III] λ5007/Hβ emission line ratio measurements with [N II]/Hα line ratios from Wuyts et al., we find that the majority of the individual star-forming regions fall along the local 'normal' abundance sequence. With the first detections of the He I λ5876 and He II λ4686 recombination lines in a distant galaxy, we probe the massive-star content of the star-forming regions in RCS0327. The majority of the star-forming regions have a He I λ5876 to Hβ ratio consistent with the saturated maximum value, which is only possible if they still contain hot O-stars. Two regions have lower ratios, implying that their last burst of new star formation ended ∼5 Myr ago. Together, the He I λ5876 and He II λ4686 to Hβ line ratios provide indirect evidence for the order in which star formation is stopping in individual star-forming knots of this high-redshift merger. We place the spatial variations of the extinction, star formation rate and ionization conditions in the context of the star formation history of RCS0327.

Preliminary observations on polar body extrusion and pronuclear formation in human oocytes using time-lapse video cinematography.

Science.gov (United States)

Payne, D; Flaherty, S P; Barry, M F; Matthews, C D

1997-03-01

In this study, we have used time-lapse video cinematography to study fertilization in 50 human oocytes that had undergone intracytoplasmic sperm injection (ICSI). Time-lapse recording commenced shortly after ICSI and proceeded for 17-20 h. Oocytes were cultured in an environmental chamber which was maintained under standard culture conditions. Overall, 38 oocytes (76%) were fertilized normally, and the fertilization rate and embryo quality were not significantly different from 487 sibling oocytes cultured in a conventional incubator. Normal fertilization followed a defined course of events, although the timing of these events varied markedly between oocytes. In 35 of the 38 fertilized oocytes (92%), there were circular waves of granulation within the ooplasm which had a periodicity of 20-53 min. The sperm head decondensed during this granulation phase. The second polar body was then extruded, and this was followed by the central formation of the male pronucleus. The female pronucleus formed in the cytoplasm adjacent to the second polar body at the same time as, or slightly after, the male pronucleus, and was subsequently drawn towards the male pronucleus until the two abutted. Both pronuclei then increased in size, the nucleoli moved around within the pronuclei and some nucleoli coalesced. During pronuclear growth, the organelles contracted from the cortex towards the centre of the oocyte, leaving a clear cortical zone. The oocyte decreased in diameter from 112 to 106 microm (P cinematography is an excellent tool for studying fertilization and early embryo development, and have demonstrated that human fertilization comprises numerous complex dynamic events.

Human second trimester amniotic fluid cells are able to create embryoid body-like structures in vitro and to show typical expression profiles of embryonic and primordial germ cells.

Science.gov (United States)

Antonucci, Ivana; Di Pietro, Roberta; Alfonsi, Melissa; Centurione, Maria Antonietta; Centurione, Lucia; Sancilio, Silvia; Pelagatti, Francesca; D'Amico, Maria Angela; Di Baldassarre, Angela; Piattelli, Adriano; Tetè, Stefano; Palka, Giandomenico; Borlongan, Cesar V; Stuppia, Liborio

2014-01-01

Human amniotic fluid-derived stem cells (AFSCs) represent a novel class of broadly multipotent stem cells sharing characteristics of both embryonic and adult stem cells. However, both the origin of these cells and their actual properties in terms of pluripotent differentiation potential are still debated. In order to verify the presence of features of pluripotency in human second trimester AFSCs, we have investigated the ability of these cells to form in vitro three-dimensional aggregates, known as embryoid bodies (EBs), and to express specific genes of embryonic stem cells (ESCs) and primordial germ cells (PGCs). EBs were obtained after 5 days of AFSC culture in suspension and showed positivity for alkaline phosphatase (AP) staining and for specific markers of pluripotency (OCT4 and SOX2). Moreover, EB-derived cells showed the expression of specific transcripts of the three germ layers. RT-PCR analysis, carried out at different culture times (second, third, fourth, fifth, and eighth passages), revealed the presence of specific markers of ESCs (such as FGF4 and DAPPA4), as well as of markers typical of PGCs and, in particular, genes involved in early stages of germ cell development (Fragilis, Stella, Vasa, c-Kit, Rnf17). Finally, the expression of genes related to the control of DNA methylation (DNMT3A, DNMT3b1, DNMT1, DNMT3L, MBD1, MBD2, MBD3, MDB4, MeCP2), as well as the lack of inactivation of the X-chromosome in female samples, was also demonstrated. Taken together, these data provide further evidence for the presence of common features among human AFSCs, PGCs, and ESCs.

Simulating the formation and evolution of galaxies with EvoL, the Padova N-body Tree-SPH code

International Nuclear Information System (INIS)

Merlin, E.; Chiosi, C.; Grassi, T.; Buonomo, U.; Chinellato, S.

2009-01-01

The importance of numerical simulations in astrophysics is constantly growing, because of the complexity, the multi-scaling properties and the non-linearity of many physical phenomena. In particular, cosmological and galaxy-sized simulations of structure formation have cast light on different aspects, giving answers to many questions, but raising a number of new issues to be investigated. Over the last decade, great effort has been devoted in Padova to develop a tool explicitly designed to study the problem of galaxy formation and evolution, with particular attention to the early-type ones. To this aim, many simulations have been run on CINECA supercomputers (see publications list below). The next step is the new release of EvoL, a Fortran N-body code capable to follow in great detail many different aspects of stellar, interstellar and cosmological physics. In particular, special care has been paid to the properties of stars and their interplay with the surrounding interstellar medium (ISM), as well as to the multiphase nature of the ISM, to the setting of the initial and boundary conditions, and to the correct description of gas physics via modern formulations of the classical Smoothed Particle Hydrodynamics algorithms. Moreover, a powerful tool to compare numerical predictions with observables has been developed, self-consistently closing the whole package. A library of new simulations, run with EvoL on CINECA supercomputers, is to be built in the next years, while new physics, including magnetic properties of matter and more exotic energy feedback effects, is to be added.

Dithiocarbamates have a common toxic effect on zebrafish body axis formation

International Nuclear Information System (INIS)

Tilton, Fred; La Du, Jane K.; Vue, Meng; Alzarban, Noor; Tanguay, Robert L.

2006-01-01

We previously determined that the dithiocarbamate pesticide sodium metam (NaM) and its active ingredient methylisothiocyanate (MITC) were developmentally toxic causing notochord distortions in the zebrafish. In this study, developing zebrafish were exposed to isothiocyanates (ITCs), dithiocarbamates (DTCs) and several degradation products to determine the teratogenic relationship of these chemical classes at the molecular level. All dithiocarbamates tested elicited notochord distortions with notochord NOELs from 2 ), a common DTC degradate, also caused distortions at concentrations >200 times the DTCs. Whole mount in situ hybridization of developmental markers for collagen (collagen2a1), muscle (myoD), and body axis formation (no tail) was perturbed well after cessation of treatment with pyrolidine-DTC (PDTC), dimethyl-DTC (DMDTC), NaM, MITC, and CS 2 . Therefore, distinct albeit related chemical classes share a common toxic effect on zebrafish notochord development. To test the responsiveness of the distortion to metal perturbation, five metal chelators and 2 metals were studied. The membrane permeable copper chelator neocuproine (NCu) was found to cause notochord distortions similar to DTC-related molecules. DMDTC and NCu treated animals were protected with copper, and collagen 2a1 and no tail gene expression patterns were identical to controls in these animals. PDTC, NaM, MITC, and CS 2 were not responsive to copper indicating that the chelation of metals is not the primary means by which these molecules elicit their developmental toxicity. Embryos treated with DMDTC, NaM, and NCu were rescued by adding triciaine (MS-222) which abolishes the spontaneous muscle contractions that begin at 18 hpf. In these animals, only collagen 2a1 expression showed a similar pattern to the other notochord distorting molecules. This indicates that the perturbation of no tail expression is in response to the muscle contractions distorting the notochord, while collagen 2a1 is

Tumor Suppressor RARRES1 Regulates DLG2, PP2A, VCP, EB1, and Ankrd26

Directory of Open Access Journals (Sweden)

Ziad J. Sahab, Michael D. Hall, Lihua Zhang, Amrita K. Cheema, Stephen W. Byers

2010-01-01

Full Text Available Retinoic Acid Receptor Responder (RARRES1 initially identified as a novel retinoic acid receptor regulated gene in the skin is a putative tumor suppressor of unknown function. RARRES1 was knocked down in immortalized human prostatic epithelial cell line PWR-1E cells and differential protein expression was identified using differential in-gel electrophoresis (DIGE followed by matrix-assisted laser desorption ionization (MALDI mass spectrometry and western Blot analysis excluding highly abundant proteins routinely identified in almost all proteomics projects. Knock-down of RARRES1: 1- down-regulates PP2A, an enzyme involved in the negative regulation of the growth hormone-stimulated signal transduction pathways; 2- down-regulates Valosin-containing protein causing impaired autophagy; 3- up-regulates the tumor suppressor disks large 2; 4- up-regulates Ankrd26 that belongs to the POTE family of genes that are highly expressed in cancer patients with poor outcome; and 5- down-regulates EB1, a protein that is involved in spindle dynamics and chromosome alignment during mitosis.

Autophagy-Associated Protein SmATG12 Is Required for Fruiting-Body Formation in the Filamentous Ascomycete Sordaria macrospora.

Science.gov (United States)

Werner, Antonia; Herzog, Britta; Frey, Stefan; Pöggeler, Stefanie

2016-01-01

In filamentous fungi, autophagy functions as a catabolic mechanism to overcome starvation and to control diverse developmental processes under normal nutritional conditions. Autophagy involves the formation of double-membrane vesicles, termed autophagosomes that engulf cellular components and bring about their degradation via fusion with vacuoles. Two ubiquitin-like (UBL) conjugation systems are essential for the expansion of the autophagosomal membrane: the UBL protein ATG8 is conjugated to the lipid phosphatidylethanolamine and the UBL protein ATG12 is coupled to ATG5. We recently showed that in the homothallic ascomycete Sordaria macrospora autophagy-related genes encoding components of the conjugation systems are required for fruiting-body development and/or are essential for viability. In the present work, we cloned and characterized the S. macrospora (Sm)atg12 gene. Two-hybrid analysis revealed that SmATG12 can interact with SmATG7 and SmATG3. To examine its role in S. macrospora, we replaced the open reading frame of Smatg12 with a hygromycin resistance cassette and generated a homokaryotic ΔSmatg12 knockout strain, which displayed slower vegetative growth under nutrient starvation conditions and was unable to form fruiting bodies. In the hyphae of S. macrospora EGFP-labeled SmATG12 was detected in the cytoplasm and as punctate structures presumed to be phagophores or phagophore assembly sites. Delivery of EGFP-labelled SmATG8 to the vacuole was entirely dependent on SmATG12.

Autophagy-Associated Protein SmATG12 Is Required for Fruiting-Body Formation in the Filamentous Ascomycete Sordaria macrospora.

Directory of Open Access Journals (Sweden)

Antonia Werner

Full Text Available In filamentous fungi, autophagy functions as a catabolic mechanism to overcome starvation and to control diverse developmental processes under normal nutritional conditions. Autophagy involves the formation of double-membrane vesicles, termed autophagosomes that engulf cellular components and bring about their degradation via fusion with vacuoles. Two ubiquitin-like (UBL conjugation systems are essential for the expansion of the autophagosomal membrane: the UBL protein ATG8 is conjugated to the lipid phosphatidylethanolamine and the UBL protein ATG12 is coupled to ATG5. We recently showed that in the homothallic ascomycete Sordaria macrospora autophagy-related genes encoding components of the conjugation systems are required for fruiting-body development and/or are essential for viability. In the present work, we cloned and characterized the S. macrospora (Smatg12 gene. Two-hybrid analysis revealed that SmATG12 can interact with SmATG7 and SmATG3. To examine its role in S. macrospora, we replaced the open reading frame of Smatg12 with a hygromycin resistance cassette and generated a homokaryotic ΔSmatg12 knockout strain, which displayed slower vegetative growth under nutrient starvation conditions and was unable to form fruiting bodies. In the hyphae of S. macrospora EGFP-labeled SmATG12 was detected in the cytoplasm and as punctate structures presumed to be phagophores or phagophore assembly sites. Delivery of EGFP-labelled SmATG8 to the vacuole was entirely dependent on SmATG12.

F-center and self-trapped exciton formation in strongly excited alkali halide crystals

International Nuclear Information System (INIS)

Kravchenko, V.A.; Yakovlev, V.Yu.

1988-01-01

Method of luminescent and absorption spectroscopy with time resolution was used to study the effect of density of electron pulse excitation (t p =10 -8 s, P=(10 5 -10 8 ) WXcm -2 ) on efficiency of η ε two-halide autolocalized exciton (TALE) and F-centers (η F ) formation in CsI, CsBr, KBr, KI alkali halide crystals. It was established that for all studied systems the elevation of P power of electron beam (EB) from 10 5 up to 5X10 7 WXcm -2 resulted to sufficient decrease of production efficiency and yield of TALE luminescence. In the case when F-centers of colour are induced predominantly by pulsed irradiation in crystals, F-center yield is independent of P. If F-centers and TALE are produced in comparable amounts (CsBr crystals, T=80 K), η ε decrease with P growth is accompanied by η F growth

Centrioles to basal bodies in the spermiogenesis of Mastotermes darwiniensis (Insecta, Isoptera).

Science.gov (United States)

Riparbelli, Maria Giovanna; Callaini, Giuliano; Mercati, David; Hertel, Horst; Dallai, Romano

2009-05-01

In addition to their role in centrosome organization, the centrioles have another distinct function as basal bodies for the formation of cilia and flagella. Centriole duplication has been reported to require two alternate assembly pathways: template or de novo. Since spermiogenesis in the termite Mastotermes darwiniensis lead to the formation of multiflagellate sperm, this process represents a useful model system in which to follow basal body formation and flagella assembly. We present evidence of a possible de novo pathway for basal body formation in the differentiating germ cell. This cell also contains typical centrosomal proteins, such as centrosomin, pericentrin-like protein, gamma-tubulin, that undergo redistribution as spermatid differentiation proceeds. The spermatid centrioles are long structures formed by nine doublet rather than triplet microtubules provided with short projections extending towards the surrounding cytoplasm and with links between doublets. The sperm basal bodies are aligned in parallel beneath the nucleus. They consist of long regions close to the nucleus showing nine doublets in a cartwheel array devoid of any projections; on the contrary, the short region close to the plasma membrane, where the sperm flagella emerge, is characterized by projections similar to those observed in the centrioles linking the basal body to the plasma membrane. It is hypothesized that this appearance is in connection with the centriole elongation and further with the flagellar axonemal organization. Microtubule doublets of sperm flagellar axonemes are provided with outer dynein arms, while inner arms are rarely visible. (c) 2009 Wiley-Liss, Inc.

eEF1A Controls ascospore differentiation through elevated accuracy, but controls longevity and fruiting body formation through another mechanism in Podospora anserina.

Science.gov (United States)

Silar, P; Lalucque, H; Haedens, V; Zickler, D; Picard, M

2001-01-01

Antisuppressor mutations in the eEF1A gene of Podospora anserina were previously shown to impair ascospore formation, to drastically increase life span, and to permit the development of the Crippled Growth degenerative process. Here, we show that eEF1A controls ascospore formation through accuracy level maintenance. Examination of antisuppressor mutant perithecia reveals two main cytological defects, mislocalization of spindle and nuclei and nuclear death. Antisuppression levels are shown to be highly dependent upon both the mutation site and the suppressor used, precluding any correlation between antisuppression efficiency and severity of the sporulation impairment. Nevertheless, severity of ascospore differentiation defect is correlated with resistance to paromomycin. We also show that eEF1A controls fruiting body formation and longevity through a mechanism(s) different from accuracy control. In vivo, GFP tagging of the protein in a way that partly retains its function confirmed earlier cytological observation; i.e., this factor is mainly diffuse within the cytosol, but may transiently accumulate within nuclei or in defined regions of the cytoplasm. These data emphasize the fact that the translation apparatus exerts a global regulatory control over cell physiology and that eEF1A is one of the key factors involved in this monitoring. PMID:11514440

Oil bodies and their associated proteins, oleosin and caleosin

DEFF Research Database (Denmark)

Frandsen, Gitte I.; Mundy, John; Tzen, Jason T. C.

2001-01-01

Oil bodies are lipid storage organelles which have been analyzed biochemically due to the economic importance of oil seeds. Although oil bodies are structurally simple, the mechanisms involved in their formation and degradation remain controversial. At present, only two proteins associated with oil....... (1999) Plant Cell Physiol 40: 1079-1086; Naested et al. (2000) Plant Mol Biol 44: 463-476]. Caleosin and caleosin-like proteins are not unique to oil bodies and are associated with an endoplasmatic reticulum subdomain in some cell types. Here we review the synthesis and degradation of oil bodies...

KSHV inhibits stress granule formation by viral ORF57 blocking PKR activation.

Directory of Open Access Journals (Sweden)

Nishi R Sharma

2017-10-01

Full Text Available TIA-1 positive stress granules (SG represent the storage sites of stalled mRNAs and are often associated with the cellular antiviral response. In this report, we provide evidence that Kaposi's sarcoma-associated herpesvirus (KSHV overcomes the host antiviral response by inhibition of SG formation via a viral lytic protein ORF57. By immunofluorescence analysis, we found that B lymphocytes with KSHV lytic infection are refractory to SG induction. KSHV ORF57, an essential post-transcriptional regulator of viral gene expression and the production of new viral progeny, inhibits SG formation induced experimentally by arsenite and poly I:C, but not by heat stress. KSHV ORF37 (vSOX bearing intrinsic endoribonuclease activity also inhibits arsenite-induced SG formation, but KSHV RTA, vIRF-2, ORF45, ORF59 and LANA exert no such function. ORF57 binds both PKR-activating protein (PACT and protein kinase R (PKR through their RNA-binding motifs and prevents PACT-PKR interaction in the PKR pathway which inhibits KSHV production. Consistently, knocking down PKR expression significantly promotes KSHV virion production. ORF57 interacts with PKR to inhibit PKR binding dsRNA and its autophosphorylation, leading to inhibition of eIF2α phosphorylation and SG formation. Homologous protein HSV-1 ICP27, but not EBV EB2, resembles KSHV ORF57 in the ability to block the PKR/eIF2α/SG pathway. In addition, KSHV ORF57 inhibits poly I:C-induced TLR3 phosphorylation. Altogether, our data provide the first evidence that KSHV ORF57 plays a role in modulating PKR/eIF2α/SG axis and enhances virus production during virus lytic infection.

Comparison of Four Protocols to Generate Chondrocyte-Like Cells from Human Induced Pluripotent Stem Cells (hiPSCs).

Science.gov (United States)

Suchorska, Wiktoria Maria; Augustyniak, Ewelina; Richter, Magdalena; Trzeciak, Tomasz

2017-04-01

Stem cells (SCs) are a promising approach to regenerative medicine, with the potential to treat numerous orthopedic disorders, including osteo-degenerative diseases. The development of human-induced pluripotent stem cells (hiPSCs) has increased the potential of SCs for new treatments. However, current methods of differentiating hiPSCs into chondrocyte-like cells are suboptimal and better methods are needed. The aim of the present study was to assess four different chondrogenic differentiation protocols to identify the most efficient method of generating hiPSC-derived chondrocytes. For this study, hiPSCs were obtained from primary human dermal fibroblasts (PHDFs) and differentiated into chondrocyte-like cells using four different protocols: 1) monolayer culture with defined growth factors (GF); 2) embryoid bodies (EBs) in a chondrogenic medium with TGF-β3 cells; 3) EBs in chondrogenic medium conditioned with human chondrocytes (HC-402-05a cell line) and 4) EBs in chondrogenic medium conditioned with human chondrocytes and supplemented with TGF-β3. The cells obtained through these four protocols were evaluated and compared at the mRNA and protein levels. Although chondrogenic differentiation of hiPSCs was successfully achieved with all of these protocols, the two fastest and most cost-effective methods were the monolayer culture with GFs and the medium conditioned with human chondrocytes. Both of these methods are superior to other available techniques. The main advantage of the conditioned medium is that the technique is relatively simple and inexpensive while the directed method (i.e., monolayer culture with GFs) is faster than any protocol described to date because it is does not require additional steps such as EB formation.

Predicting hydrocarbon potential of an earth formation underlying water

International Nuclear Information System (INIS)

Damaison, G.J.; Kaplan, I.R.

1981-01-01

A method for the on-site collection and examination of small concentrations of a carbonaceous gas, e.g. methane, dissolved in a body of water overlying an earth formation to predict hydrocarbon potential of the earth formation under the body of water, the formation being a source of carbonaceous gas, comprises at a known geographic location sampling the water at a selected flow rate and at a selected depth; continuously vacuum separating the water into liquid and gas phases; separating a selected carbonaceous gas from interfering gas species in the presence of an air carrier vented to atmosphere at a known flow rate; and quantitatively oxidizing the selected gas and then cryogenically trapping an oxidant thereof in the presence of said air carrier to provide for an accurate isotopic examination. (author)

STAR FORMATION EFFICIENCY IN THE COOL CORES OF GALAXY CLUSTERS

International Nuclear Information System (INIS)

McDonald, Michael; Veilleux, Sylvain; Mushotzky, Richard; Reynolds, Christopher; Rupke, David S. N.

2011-01-01

We have assembled a sample of high spatial resolution far-UV (Hubble Space Telescope Advanced Camera for Surveys/Solar Blind Channel) and Hα (Maryland-Magellan Tunable Filter) imaging for 15 cool core galaxy clusters. These data provide a detailed view of the thin, extended filaments in the cores of these clusters. Based on the ratio of the far-UV to Hα luminosity, the UV spectral energy distribution, and the far-UV and Hα morphology, we conclude that the warm, ionized gas in the cluster cores is photoionized by massive, young stars in all but a few (A1991, A2052, A2580) systems. We show that the extended filaments, when considered separately, appear to be star forming in the majority of cases, while the nuclei tend to have slightly lower far-UV luminosity for a given Hα luminosity, suggesting a harder ionization source or higher extinction. We observe a slight offset in the UV/Hα ratio from the expected value for continuous star formation which can be modeled by assuming intrinsic extinction by modest amounts of dust (E(B - V) ∼ 0.2) or a top-heavy initial mass function in the extended filaments. The measured star formation rates vary from ∼0.05 M sun yr -1 in the nuclei of non-cooling systems, consistent with passive, red ellipticals, to ∼5 M sun yr -1 in systems with complex, extended, optical filaments. Comparing the estimates of the star formation rate based on UV, Hα, and infrared luminosities to the spectroscopically determined X-ray cooling rate suggests a star formation efficiency of 14 +18 -8 %. This value represents the time-averaged fraction, by mass, of gas cooling out of the intracluster medium, which turns into stars and agrees well with the global fraction of baryons in stars required by simulations to reproduce the stellar mass function for galaxies. This result provides a new constraint on the efficiency of star formation in accreting systems.

Genetic background effects of keratin 8 and 18 in a DDC-induced hepatotoxicity and Mallory-Denk body formation mouse model.

Science.gov (United States)

Haybaeck, Johannes; Stumptner, Cornelia; Thueringer, Andrea; Kolbe, Thomas; Magin, Thomas M; Hesse, Michael; Fickert, Peter; Tsybrovskyy, Oleksiy; Müller, Heimo; Trauner, Michael; Zatloukal, Kurt; Denk, Helmut

2012-06-01

Keratin 8 (K8) and keratin 18 (K18) form the major hepatocyte cytoskeleton. We investigated the impact of genetic loss of either K8 or K18 on liver homeostasis under toxic stress with the hypothesis that K8 and K18 exert different functions. krt8⁻/⁻ and krt18⁻/⁻ mice crossed into the same 129-ola genetic background were treated by acute and chronic administration of 3,5-diethoxy-carbonyl-1,4-dihydrocollidine (DDC). In acutely DDC-intoxicated mice, macrovesicular steatosis was more pronounced in krt8⁻/⁻ and krt18⁻/⁻ compared with wild-type (wt) animals. Mallory-Denk bodies (MDBs) appeared in krt18⁻/⁻ mice already at an early stage of intoxication in contrast to krt8⁻/⁻ mice that did not display MDB formation when fed with DDC. Keratin-deficient mice displayed significantly lower numbers of apoptotic hepatocytes than wt animals. krt8⁻/⁻, krt18⁻/⁻ and control mice displayed comparable cell proliferation rates. Chronically DDC-intoxicated krt18⁻/⁻ and wt mice showed a similarly increased degree of steatohepatitis with hepatocyte ballooning and MDB formation. In krt8⁻/⁻ mice, steatosis was less, ballooning, and MDBs were absent. krt18⁻/⁻ mice developed MDBs whereas krt8⁻/⁻ mice on the same genetic background did not, highlighting the significance of different structural properties of keratins. They are independent of the genetic background as an intrinsic factor. By contrast, toxicity effects may depend on the genetic background. krt8⁻/⁻ and krt18⁻/⁻ mice on the same genetic background show similar sensitivity to DDC intoxication and almost resemble wt animals regarding survival, degree of porphyria, liver-to-body weight ratio, serum bilirubin and liver enzyme levels. This stands in contrast to previous work where krt8⁻/⁻ and krt18⁻/⁻ mice on different genetic backgrounds were investigated.

Assessing reprogramming by chimera formation and tetraploid complementation.

Science.gov (United States)

Li, Xin; Xia, Bao-long; Li, Wei; Zhou, Qi

2015-01-01

Pluripotent stem cells can be evaluated by pluripotent markers expression, embryoid body aggregation, teratoma formation, chimera contribution and even more, tetraploid complementation. Whether iPS cells in general are functionally equivalent to normal ESCs is difficult to establish. Here, we present the detailed procedure for chimera formation and tetraploid complementation, the most stringent criterion, to assessing pluripotency.

Formation of an ultracarbonaceous Antarctic micrometeorite through minimal aqueous alteration in a small porous icy body

Science.gov (United States)

Yabuta, Hikaru; Noguchi, Takaaki; Itoh, Shoichi; Nakamura, Tomoki; Miyake, Akira; Tsujimoto, Shinichi; Ohashi, Noriaki; Sakamoto, Naoya; Hashiguchi, Minako; Abe, Ken-ichi; Okubo, Aya; Kilcoyne, A. L. David; Tachibana, Shogo; Okazaki, Ryuji; Terada, Kentaro; Ebihara, Mitsuru; Nagahara, Hiroko

2017-10-01

have been necessary for the formation of the UCAMM. The GEMS grains depleted in Mg and S in the UCAMM prove a very weak degree of aqueous alteration; weaker than that of carbonaceous chondrites. Short-duration weak alteration probably caused by planetesimal shock locally melted cometary ice grains and released water that dissolved the organics; the fluid would likely have not mobilized because of the very low thermal conductivity of the porous icy body. This event allowed the formation of the large organic puddle of the UCAMM, as well as organic matter sulfurization, formation of thin membrane-like layers of minerals, and deformation of organic nanoglobules.

Relation between histamine release and dye permeability of pulmonary blood-air barrier in x-irradiated rat

Energy Technology Data Exchange (ETDEWEB)

Yamazaki, H [Kobe Univ. (Japan). School of Medicine

1976-04-01

The histamine-release kinetics and the influence of released histamine on the permeability of the pulmonary blood-air(BA) barrier during the early period after either whole-body or thoracic x irradiation of the rat were studied. Histamine contents of skin and lung of the irradiated rat decreased rapidly, reaching a minimum at 5 h, and this histamine depletion continued for at least 7 days. Conversely, in circulating blood histamine increased during the early period of 5 h and then decreased gradually. This early increase was linear up to 500R and then became saturated between 500 and 1,000R. Administration of polymixine B (5mg/100g body weight) to rats liberated histamine similarly. Rat sera containg histamine released soon after irradiation enhanced the capillary permeability of Evans blue(EB) in the guinea pig skin reaction, which was effectively countered by pretreatment of the guinea pig with anti-histaminic pyribenzamine (29..mu..g/100g body weight), but not by anti-serotonic chlorpromazine (0.3mg/100g body weight). Similarly, perhaps only the EB-bound serum albumin (EB-albumin), that was seen in alveolar perfusate, penetrated more through the pulmonary BA-barrier with increasing x-ray dose, in parallel with the increase in blood histamine. Pyribenzamine inhibited this effect effectively, but cysteamine (a radical scavenger) did so only partially. Thus, it seems possible that at soon after x irradiation the enhanced permeability of EB-albumin through the BA barrier of rat lung is due preferentially to the pharmacologic action of released histamine and subsidiarily to radiation damage to pulmonary cells.

Teaching practices epistemologically differentiated about human body learning

Directory of Open Access Journals (Sweden)

Rosália Maria Ribeiro de Aragão

2011-12-01

Full Text Available How could we teach about THE HUMAN BODY as a different way, in both epistemological and pedagogical approaches? How could we leave behind stagnant as well as stagnating aspects of traditional way of teaching, such as the fragmentation/segmentation of contents, the far away reality, the excessive use of details or else, whenever learning about our own body? These are some of the questions we have considered when trying to escape the bad influence which came from our "environment formation" - putting it on all the marks we have acquired inside or even outside school - trying to overview as meaning our body working...in constant interaction with the surrounding ambient. Among those pointed kind of formation marks we frequently acquire from studying at the University - which need to be transcended —here we come to detach those innumerable contacts with both anatomized and misfigurated supposed human bodies' which didn't even look like actual human bodies, because they could never seem to have sheltered life inside themselves. They were inert as well as static bodies, only used as a such of vain "didactic materials" that could/can permit many teachers on their educational formation to focus a certain teaching approach which only seeks both the students' memorization of an infinitude of "complicated words", and to structure the systems -by several procedures of nouns definition and/or classification - as part of the so called biological organism. In order to do a different way of teaching, we have based our approach on three alternative teaching methodologies which focus these matters under a constructive perspective. On those three focused studies, it is possible to observe that some very principles of a present day teaching approach were there considered to achieve some of them: the respect for the students' previous ideas; the understanding about knowledge as something that is not established for good but as ever changeable and, at last, the

Body piercing: complications and prevention of health risks.

Science.gov (United States)

Holbrook, Jaimee; Minocha, Julia; Laumann, Anne

2012-02-01

Body and earlobe piercing are common practices in the USA today. Minor complications including infection and bleeding occur frequently and, although rare, major complications have been reported. Healthcare professionals should be cognizant of the medical consequences of body piercing. Complications vary depending on the body-piercing site, materials used, experience of the practitioner, hygiene regimens, and aftercare by the recipient. Localized infections are common. Systemic infections such as viral hepatitis and toxic shock syndrome and distant infections such as endocarditis and brain abscesses have been reported. Other general complications include allergic contact dermatitis (e.g. from nickel or latex), bleeding, scarring and keloid formation, nerve damage, and interference with medical procedures such as intubation and blood/organ donation. Site-specific complications have been reported. Oral piercings may lead to difficulty speaking and eating, excessive salivation, and dental problems. Oral and nasal piercings may be aspirated or become embedded, requiring surgical removal. Piercing tracts in the ear, nipple, and navel are prone to tearing. Galactorrhea may be caused by stimulation from a nipple piercing. Genital piercings may lead to infertility secondary to infection, and obstruction of the urethra secondary to scar formation. In men, priapism and fistula formation may occur. Women who are pregnant or breastfeeding and have a piercing or are considering obtaining one need to be aware of the rare complications that may affect them or their child. Though not a 'complication' per se, many studies have reported body piercing as a marker for high-risk behavior, psychopathologic symptoms, and anti-social personality traits. When it comes to piercing complications, prevention is the key. Body piercers should take a complete medical and social history to identify conditions that may predispose an individual to complications, and candidates should choose a

Transcriptome dynamics of human pluripotent stem cell-derived contracting cardiomyocytes using an embryoid body model with fetal bovine serum.

Science.gov (United States)

Jung, Kwang Bo; Son, Ye Seul; Lee, Hana; Jung, Cho-Rok; Kim, Janghwan; Son, Mi-Young

2017-07-25

Cardiomyocyte (CM) differentiation techniques for generating adult-like mature CMs remain imperfect, and the plausible underlying mechanisms remain unclear; however, there are a number of current protocols available. Here, to explore the mechanisms controlling cardiac differentiation, we analyzed the genome-wide transcription dynamics occurring during the differentiation of human pluripotent stem cells (hPSCs) into CMs using embryoid body (EB) formation. We optimized and updated the protocol to efficiently generate contracting CMs from hPSCs by adding fetal bovine serum (FBS) as a medium supplement, which could have a significant impact on the efficiency of cardiac differentiation. To identify genes, biological processes, and pathways involved in the cardiac differentiation of hPSCs, integrative and comparative analyses of the transcriptome profiles of differentiated CMs from hPSCs and of control CMs of the adult human heart (CM-AHH) were performed using gene ontology, functional annotation clustering, and pathway analyses. Several genes commonly regulated in the differentiated CMs and CM-AHH were enriched in pathways related to cell cycle and nucleotide metabolism. Strikingly, we found that current differentiation protocols did not promote sufficient expression of genes involved in oxidative phosphorylation to differentiate CMs from hPSCs compared to the expression levels in CM-AHH. Therefore, to obtain mature CMs similar to CM-AHH, these deficient pathways in CM differentiation, such as energy-related pathways, must be augmented prior to use for in vitro and in vivo applications. This approach opens up new avenues for facilitating the utilization of hPSC-derived CMs in biomedical research, drug evaluation, and clinical applications for patients with cardiac failure.

Current Status and Performance Tests of Korea Heat Load Test Facility KoHLT-EB

Energy Technology Data Exchange (ETDEWEB)

Kim, Sukkwon; Jin, Hyunggon; Shin, Kyuin; Choi, Boguen; Lee, Eohwak; Yoon, Jaesung; Lee, Dongwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Duckhoi; Cho, Seungyon [National Fusion Research Institute, Daejeon (Korea, Republic of)

2013-05-15

A commissioning test has been scheduled to establish the installation and preliminary performance experiments of the copper hypervapotron mockups. And a qualification test will be performed to evaluate the CuCrZr duct liner in the ITER neutral beam injection facility and the ITER first wall small-scale mockups of the semi-prototype, at up to 1.5 and 5 MW/m{sup 2} high heat flux. Also, this system will be used to test other PFCs for ITER and materials for tokamak reactors. Korean high heat flux test facility(KoHLT-EB; Korea Heat Load Test facility - Electron Beam) by using an electron beam system has been constructed in KAERI to perform the qualification test for ITER blanket FW semi-prototype mockups, hypervapotron cooling devices in fusion devices, and other ITER plasma facing components. The commissioning and performance tests with the supplier of e-gun system have been performed on November 2012. The high heat flux test for hypervapotron cooling device and calorimetry were performed to measure the surface heat flux, the temperature profile and cooling performance. Korean high heat flux test facility for the plasma facing components of nuclear fusion machines will be constructed to evaluate the performance of each component. This facility for the plasma facing materials will be equipped with an electron beam system with a 60 kV acceleration gun.

Evolution of photo-stimulated luminescence of EB-PVD/(Ni, Pt)Al thermal barrier coatings

International Nuclear Information System (INIS)

Wen Mei; Jordan, Eric H.; Gell, Maurice

2005-01-01

Experiments are described which were designed to assess the suitability of photo-stimulated luminescence piezo-spectroscopy (PLPS) measurements as a basis for non-destructive inspection (NDI) and determination of life remaining of thermal barrier coatings (TBCs). Thermal cyclic tests were conducted on 7 wt.% Y 2 O 3 stabilized ZrO 2 (YSZ) electron beam physical vapor deposited (EB-PVD)/(Ni, Pt)Al/CMSX-4 TBCs at two temperatures 1151 and 1121 deg. C. The evolution of PLPS spectral characteristics (peak frequency shift, peak width and area ratio of peaks) was studied as a function of thermal cycles. It was observed that the average thermally grown oxide (TGO) stress and its standard deviation, and the area ratio of peaks show systematic change with thermal cycling, indicating that these characteristics can be used for NDI and determination of life remaining. The average TGO stress increases initially and then decreases monotonically with thermal cycling. The rate of change in the stress can be related to specimen life: the shallower the slope, the higher the life. The peak area ratio also decreases monotonically with cycling. The average TGO stress changes in a systematic manner versus remaining life fraction independent of temperature. Remaining life predictions were made based on average stress versus life fraction, which resulted in life assessments within ±13% of actual values excluding one specimen with abnormal behavior

Expression of the major outer membrane protein (MOMP) of Chlamydophila abortus, Chlamydophila pecorum, and Chlamydia suis in Escherichia coli using an arabinose-inducible plasmid vector.

Science.gov (United States)

Hoelzle, L E; Hoelzle, K; Wittenbrink, M M

2003-10-01

The ompA genes encoding the 40 kDa major outer membrane protein (MOMP) of Chlamydophila (Ch.) abortus, Ch. pecorum, and Chlamydia (C.) suis were cloned into the arabinose-inducible plasmid vector pBADMycHis, and recombinant MOMPs (rMOMP) from the three chlamydial species were expressed at high levels in Escherichia (E.) coli. The proteins lacking the 22 aa N-terminal signal peptide were expressed as insoluble cytoplasmic inclusion bodies which were readily purified using immobilized metal-affinity chromatography. The rMOMPs including the N-terminal signal peptide were expressed and translocated as a surface-exposed immunoaccessible protein into the outer membrane of E. coli. Transformants expressing this full-length rMOMP were significantly reduced in viability. Purified native elementary bodies (EB) and rMOMPs of the three chlamydial species purified from the E. coli cytoplasm were used for immunization of rabbits. The resulting sera were analysed for their ability to recognize homologous and heterologous rMOMP and native EB. When testing rMOMP antisera against rMOMP and EB antigens, marked cross-reactivities were detected between the three species. Using EB antisera and rMOMPs as antigens, a significant species-specific reactivity was measured.

Benchmarking the evaluated proton differential cross sections suitable for the EBS analysis of natSi and 16O

Science.gov (United States)

Kokkoris, M.; Dede, S.; Kantre, K.; Lagoyannis, A.; Ntemou, E.; Paneta, V.; Preketes-Sigalas, K.; Provatas, G.; Vlastou, R.; Bogdanović-Radović, I.; Siketić, Z.; Obajdin, N.

2017-08-01

The evaluated proton differential cross sections suitable for the Elastic Backscattering Spectroscopy (EBS) analysis of natSi and 16O, as obtained from SigmaCalc 2.0, have been benchmarked over a wide energy and angular range at two different accelerator laboratories, namely at N.C.S.R. 'Demokritos', Athens, Greece and at Ruđer Bošković Institute (RBI), Zagreb, Croatia, using a variety of high-purity thick targets of known stoichiometry. The results are presented in graphical and tabular forms, while the observed discrepancies, as well as, the limits in accuracy of the benchmarking procedure, along with target related effects, are thoroughly discussed and analysed. In the case of oxygen the agreement between simulated and experimental spectra was generally good, while for silicon serious discrepancies were observed above Ep,lab = 2.5 MeV, suggesting that a further tuning of the appropriate nuclear model parameters in the evaluated differential cross-section datasets is required.

One or many? Which and how many parenting variables should be targeted in interventions to reduce children's externalizing behavior?

Science.gov (United States)

Loop, Laurie; Mouton, Bénédicte; Stievenart, Marie; Roskam, Isabelle

2017-05-01

This research compared the efficacy of two parenting interventions that vary according to the number and the nature of variables in reducing preschoolers' externalizing behavior (EB). The goal was to identify which parenting intervention format (one-variable versus two-variable) caused higher behavioral adjustment in children. The first was a one-variable intervention manipulating parental self-efficacy beliefs. The second was a two-variable intervention manipulating both parents' self-efficacy beliefs and emotion coaching practices. The two interventions shared exactly the same design, consisting of eight parent group sessions. Effect on children's EB and observed behaviors were evaluated through a multi-method assessment at three points (pre-test, post-test and follow-up). The results highlighted that compared to the waitlist condition, the two intervention formats tended to cause a significant reduction in children's EB reported by their parent. However, the one-variable intervention was found to lead to a greater decrease in children's EB at follow-up. The opposite was reported for children's observed behavior, which was improved to a greater extent in the two-variable intervention at post-test and follow-up. The results illustrated that interventions' format cannot be considered as purely interchangeable since their impact on children's behavior modification is different. The results are discussed for their research and clinical implications. Copyright © 2017 Elsevier Ltd. All rights reserved.

Importin-α7 Is Involved in the Formation of Ebola Virus Inclusion Bodies but Is Not Essential for Pathogenicity in Mice.

Science.gov (United States)

Gabriel, Gülsah; Feldmann, Friederike; Reimer, Rudolph; Thiele, Swantje; Fischer, Meike; Hartmann, Enno; Bader, Michael; Ebihara, Hideki; Hoenen, Thomas; Feldmann, Heinz

2015-10-01

Ebola virus (EBOV) protein 24 antagonizes the host interferon (IFN) response by hijacking select nuclear importin-α isoforms. Thereby, it blocks STAT1-mediated IFN-α/β and IFN-γ synthesis. However, owing to the lack of importin-α knockout animal models in the past, their role in EBOV pathogenesis remained largely unknown. Here, we demonstrate that importin-α7 is involved in the formation of EBOV inclusion bodies and replication. However, deletion of the gene encoding importin-α7 was not sufficient to increase survival rates among mice infected with EBOV. © The Author 2015. Published by Oxford University Press on behalf of the Infectious Diseases Society of America. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Process of egg formation in the female body cavity and fertilization in male eggs of Phytoseiulus persimilis (Acari: Phytoseiidae).

Science.gov (United States)

Toyoshima, S; Nakamura, M; Nagahama, Y; Amano, H

2000-01-01

The process of egg formation in the body cavity of a phytoseiid mite, Phytoseiulus persimilis, was observed to examine fertilization of male eggs. After insemination, one of the ova at the periphery of the ovary began to expand, taking up yolk. Two pronuclei appeared in the expanded egg, located dorsally in the ovary, and yolk granules were formed gradually. After the egg became filled with yolk granules the two pronuclei fused. The egg moved via the narrow entrance at the ventral region into the oviduct, where the eggshell was formed. When the eggshell was complete, and while embryogenesis proceeded, the egg was deposited. In the meantime some ova began to expand sequentially and two joining pronuclei appeared in expanding eggs. The joining pronuclei in the first egg proved male diploidy. This is additional evidence of pseudo-arrhenotoky in this phytoseiid mite species, since the first eggs developed into males.

Voluntary self-touch increases body ownership

Directory of Open Access Journals (Sweden)

Masayuki eHara

2015-10-01

Full Text Available Experimental manipulations of body ownership have indicated that multisensory integration is central to forming bodily self-representation. Voluntary self-touch is a unique multisensory situation involving corresponding motor, tactile and proprioceptive signals. Yet, even though self-touch is frequent in everyday life, its contribution to the formation of body ownership is not well understood. Here we investigated the role of voluntary self-touch in body ownership using a novel adaptation of the rubber hand illusion (RHI, in which a robotic system and virtual reality allowed participants self-touch of real and virtual hands. In the first experiment, active and passive self-touch were applied in the absence of visual feedback. In the second experiment, we tested the role of visual feedback in this bodily illusion. Finally, in the third experiment, we compared active and passive self-touch to the classical RHI in which the touch is administered by the experimenter. We hypothesized that active self-touch would increase ownership over the virtual hand through the addition of motor signals strengthening the bodily illusion. The results indicated that active self-touch elicited stronger illusory ownership compared to passive self-touch and sensory only stimulation, and indicate an important role of active self-touch in the formation of bodily self.

Dark-ages Reionization and Galaxy Formation Simulation - XIV. Gas accretion, cooling, and star formation in dwarf galaxies at high redshift

Science.gov (United States)

Qin, Yuxiang; Duffy, Alan R.; Mutch, Simon J.; Poole, Gregory B.; Geil, Paul M.; Mesinger, Andrei; Wyithe, J. Stuart B.

2018-06-01

We study dwarf galaxy formation at high redshift (z ≥ 5) using a suite of high-resolution, cosmological hydrodynamic simulations and a semi-analytic model (SAM). We focus on gas accretion, cooling, and star formation in this work by isolating the relevant process from reionization and supernova feedback, which will be further discussed in a companion paper. We apply the SAM to halo merger trees constructed from a collisionless N-body simulation sharing identical initial conditions to the hydrodynamic suite, and calibrate the free parameters against the stellar mass function predicted by the hydrodynamic simulations at z = 5. By making comparisons of the star formation history and gas components calculated by the two modelling techniques, we find that semi-analytic prescriptions that are commonly adopted in the literature of low-redshift galaxy formation do not accurately represent dwarf galaxy properties in the hydrodynamic simulation at earlier times. We propose three modifications to SAMs that will provide more accurate high-redshift simulations. These include (1) the halo mass and baryon fraction which are overestimated by collisionless N-body simulations; (2) the star formation efficiency which follows a different cosmic evolutionary path from the hydrodynamic simulation; and (3) the cooling rate which is not well defined for dwarf galaxies at high redshift. Accurate semi-analytic modelling of dwarf galaxy formation informed by detailed hydrodynamical modelling will facilitate reliable semi-analytic predictions over the large volumes needed for the study of reionization.

Dark-ages Reionization and Galaxy Formation Simulation - XIV. Gas accretion, cooling and star formation in dwarf galaxies at high redshift

Science.gov (United States)

Qin, Yuxiang; Duffy, Alan R.; Mutch, Simon J.; Poole, Gregory B.; Geil, Paul M.; Mesinger, Andrei; Wyithe, J. Stuart B.

2018-03-01

We study dwarf galaxy formation at high redshift (z ≥ 5) using a suite of high-resolution, cosmological hydrodynamic simulations and a semi-analytic model (SAM). We focus on gas accretion, cooling and star formation in this work by isolating the relevant process from reionization and supernova feedback, which will be further discussed in a companion paper. We apply the SAM to halo merger trees constructed from a collisionless N-body simulation sharing identical initial conditions to the hydrodynamic suite, and calibrate the free parameters against the stellar mass function predicted by the hydrodynamic simulations at z = 5. By making comparisons of the star formation history and gas components calculated by the two modelling techniques, we find that semi-analytic prescriptions that are commonly adopted in the literature of low-redshift galaxy formation do not accurately represent dwarf galaxy properties in the hydrodynamic simulation at earlier times. We propose 3 modifications to SAMs that will provide more accurate high-redshift simulations. These include 1) the halo mass and baryon fraction which are overestimated by collisionless N-body simulations; 2) the star formation efficiency which follows a different cosmic evolutionary path from the hydrodynamic simulation; and 3) the cooling rate which is not well defined for dwarf galaxies at high redshift. Accurate semi-analytic modelling of dwarf galaxy formation informed by detailed hydrodynamical modelling will facilitate reliable semi-analytic predictions over the large volumes needed for the study of reionization.

TRIM5α association with cytoplasmic bodies is not required for antiretroviral activity

International Nuclear Information System (INIS)

Song, Byeongwoon; Diaz-Griffero, Felipe; Park, Do Hyun; Rogers, Thomas; Stremlau, Matthew; Sodroski, Joseph

2005-01-01

The tripartite motif (TRIM) protein, TRIM5α, restricts infection by particular retroviruses. Many TRIM proteins form cytoplasmic bodies of unknown function. We investigated the relationship between cytoplasmic body formation and the structure and antiretroviral activity of TRIM5α. In addition to diffuse cytoplasmic staining, the TRIM5α proteins from several primate species were located in cytoplasmic bodies of different sizes; by contrast, TRIM5α from spider monkeys did not form cytoplasmic bodies. Despite these differences, all of the TRIM5α proteins exhibited the ability to restrict infection by particular retroviruses. Treatment of cells with geldanamycin, an Hsp90 inhibitor, resulted in disappearance or reduction of the TRIM5α-associated cytoplasmic bodies, yet exerted little effect on the restriction of retroviral infection. Studies of green fluorescent protein-TRIM5α fusion proteins indicated that no TRIM5α domain is specifically required for association with cytoplasmic bodies. Apparently, the formation of cytoplasmic bodies is not required for the antiretroviral activity of TRIM5α

Practical and safe implementation of disposal with prefabricated EBS modules

International Nuclear Information System (INIS)

Kawamura, Hideki; McKinley, Ian G.; Neall, Fiona B.

2008-01-01

The use of prefabricated EBS modules ('PEMs') to minimise the problems involved with handling compacted bentonite and ensuring that it is emplaced to established quality levels has been investigated in various national programmes for disposal of both HLW and SF. To date, however, this has tended to be decoupled from studies of related operational aspects such as assessing / minimising the consequences of use of concrete for support structures, ensuring ease of tele-operated reversal of waste packages during emplacement (e.g. in the event of operational disturbances) / retrieval at a later time, logistical optimisation (especially for programmes with large waste inventories) and cost minimisation. It is clear that specific aspects of operational safety and practicality can be considerably enhanced if designs are modified with a focus on them. It is trickier to provide optimised solutions, which simultaneously address all these critical points. Nevertheless, with a bit of lateral thinking, it appears possible to devise options that may not only ease the operational phase, but may also actually improve post-closure safety case robustness - although improved, more realistic performance assessment codes and databases will be needed to demonstrate this rigorously. To illustrate this approach, an example will be presented based of disposal of vitrified HLW in a fractured hard rock; the general principles involved are, however, also applicable to other higher activity wastes and other host rocks. Key aspects of the design are: Optimisation of PEM design for both short-term and long-term performance; Development of a rail emplacement system which eases remote handled emplacement / recovery; Large diameter, lined emplacement tunnels to ensure operational robustness; Use of multi-package overpacks (e.g. 6 HLW containers in each PEM) and short tunnels to ease emplacement logistics; and Backfilling with a non-swelling sacrificial pH buffer (eases handling and improves

Modeling of Coupled Thermo-Hydro-Mechanical-Chemical Processes for Bentonite in a Clay-rock Repository for Heat-generating Nuclear Waste

Science.gov (United States)

Xu, H.; Rutqvist, J.; Zheng, L.; Birkholzer, J. T.

2016-12-01

Engineered Barrier Systems (EBS) that include a bentonite-based buffer are designed to isolate the high-level radioactive waste emplaced in tunnels in deep geological formations. The heat emanated from the waste can drive the moisture flow transport and induce strongly coupled Thermal (T), Hydrological (H), Mechanical (M) and Chemical (C) processes within the bentonite buffer and may also impact the evolution of the excavation disturbed zone and the sealing between the buffer and walls of an emplacement tunnel The flow and contaminant transport potential along the disturbed zone can be minimized by backfilling the tunnels with bentonite, if it provides enough swelling stress when hydrated by the host rock. The swelling capability of clay minerals within the bentonite is important for sealing gaps between bentonite block, and between the EBS and the surrounding host rock. However, a high temperature could result in chemical alteration of bentonite-based buffer and backfill materials through illitization, which may compromise the function of these EBS components by reducing their plasticity and capability to swell under wetting. Therefore, an adequate THMC coupling scheme is required to understand and to predict the changes of bentonite for identifying whether EBS bentonite can sustain higher temperatures. More comprehensive links between chemistry and mechanics, taking advantage of the framework provided by a dual-structure model, named Barcelona Expansive Model (BExM), was implemented in TOUGHREACT-FLAC3D and is used to simulate the response of EBS bentonite in in clay formation for a generic case. The current work is to evaluate the chemical changes in EBS bentonite and the effects on the bentonite swelling stress under high temperature. This work sheds light on the interaction between THMC processes, evaluates the potential deterioration of EBS bentonite and supports the decision making in the design of a nuclear waste repository in light of the maximum allowance

How Do Rare Earth Elements (Lanthanoids Affect Root Development and Protocorm-Like Body Formation in Hybrid CYMBIDIUM?

Directory of Open Access Journals (Sweden)

Teixeira da Silva Jaime A.

2014-09-01

Full Text Available Only few studies in the plant tissue culture literature have examined the impact of lanthanoids, or rare earth elements, on in vitro plant organogenesis. In this study, using a model plant, hybrid Cymbidium Twilight Moon ‘Day Light’, the impact of six lanthanoids (lanthanum (III nitrate hexahydrate (La(NO33 · 6H2O, cerium (III nitrate hexahydrate (Ce(NO33 · 6H2O, neodymium (III nitrate hexahydrate (Nd(NO33 · 6H2O, praseodymium (III nitrate hexahydrate (Pr(NO33 · 6H2O, samarium (III nitrate hexahydrate (Sm(NO33 · 6H2O, gadolinium (III nitrate hexahydrate (Gd(NO33 · 6H2O on new protocorm-like body (neo-PLB formation on Teixeira Cymbidium (TC medium was examined. 0 (control, 1, 2, 4 and 8 mg·dm-3 of each lanthanoid was tested. All lanthanoids could produce more neo-PLBs and neo-PLB fresh weight than TC medium lacking plant growth regulators (PGRs, suggesting some PGR-like ability of lanthanoids, although PLB-related traits (percentage of half-PLBs forming neo-PLBs; number of neo-PLBs formed per half-PLB; fresh weight of half-PLB + neo-PLBs was always significantly lower than TC medium containing PGRs. Except for Gd, all other lanthanoids had no negative impact on the number of new leaves from neo-PLB-derived shoots, but all lanthanoids showed a significantly lower plant height, shoot fresh weight and shoot dry weight and, in most cases, SPAD (chlorophyll content value. In addition, using the same concentration of the six lanthanoids, the ability to fortify root formation of neo-PLB-derived plantlets was also assessed. Except for Sm, all other lanthanoids significantly increased the number of roots, root fresh and dry weight.

Star formation in N-body simulations .1. The impact of the stellar ultraviolet radiation on star formation

NARCIS (Netherlands)

Gerritsen, JPE; Icke, [No Value

We present numerical simulations of isolated disk galaxies including gas dynamics and star formation. The gas is allowed to cool to 10 K, while heating of the gas is provided by the far-ultraviolet flux of all stars. Stars are allowed to form from the gas according to a Jeans instability criterion:

Oral Manifestations and Dental Management of Epidermolysis Bullosa Simplex.

Science.gov (United States)

Scheidt, Lisa; Sanabe, Mariane Emi; Diniz, Michele Baffi

2015-01-01

Epidermolysis bullosa (EB) is a group of hereditary chronic disorders, characterized by fragility of the skin and mucous membranes in response to minor mechanical trauma. The objective of this study was to report the case of a young girl diagnosed with epidermolysis bullosa simplex (EBS), transmitted by an autosomal dominant gene. Cutaneous findings included blisters and dystrophy following minimal friction. Recurrent blisters and vesicle formation on the hard palate were the main oral findings. In conclusion, publications concerning the oral and clinical manifestations of EBS are important for providing knowledge and an early multidisciplinary approach that prevents blister formation and improves these patients' quality of life, with the dentist playing an important role in oral health management. How to cite this article: Scheidt L, Sanabe ME, Diniz MB. Oral Manifestations and Dental Management of Epidermolysis Bullosa Simplex. Int J Clin Pediatr Dent 2015;8(3):239-241.

Prospects of utilization of EB irradiation technology to augment control of SO2 and other emissions from Chilean copper smelting plants

International Nuclear Information System (INIS)

Villanueva, L.; Ahumada, L.; Ellison, W.; Chmielewski, A.G.; Zimek, Z.

1997-01-01

A technical study including testing and cost analysis for commercial use of selected processes has been conducted. Analysis, affirmation and evaluation of potential utilization of applicable SO 2 -removal process for off-gases, including electron-beam irradiation, for incrementally improving abatement of SO 2 /SO 3 emissions from existing copper smelting facilities in Chile has been carried out. Off-gases are characterized by SO 2 content higher than 3,000 ppm, a complex chemical composition and highly oxidizing conditions, along with cyclical and fluctuating generation. Laboratory tests with simulated high-SO 2 -content process were performed at Institute of Nuclear Chemistry and Technology. Test work proved the technical feasibility of removing SO 2 from (ultra-high SO 2 contents) gases by E-beam irradiation with ammonia injection. A laboratory unit with flow rate of 20 Nm 3 /h equiped with electron accelerator of 800 keV beam energy was used. Influence of different parameters on SO 2 removal efficiency, like temperature, irradiation dose, ammonia stoichiometry and water vapor content, has been established. Tests covered a high SO 2 content range, 2,000 to 10,000 ppm. A generic schematic design has been devised to system arrangement, performance and control requirements. It encompasses upgrading of in-plant ventilation to the extent required by health standards, together with gas cleaning system incorporating the EB Process. The arrangement of the facilities provides for gathering and treating off-gas from selected fugitive emission sources on a continuos basis, at the same time in-drafting a minimum amount of tramp air. An introductory dry dedusting stage, when required, uses condictioned activated carbon injection in conjunction with a fabric filter to efficiently treat raw gas and remove heavy metals, including arsenic, along with particulate matter. Main conclusion of stages of this work is that the EB Process is a simple and appropriate, cost

Application of EB welding to fabrication of vacuum chamber of heliotron E

International Nuclear Information System (INIS)

Kita, Hisanao; Wada, Tatsuji; Nakazaki, Takamitsu; Akutsu, Yoji; Kazawa, Yoshiaki

1981-01-01

Heliotron E, which is a large-scaled device of Heliotron series, is in operation in Kyoto University. Target plasma parameters of this machine are as follows; plasma density 1 x 10 20 m -3 , electron temperature 1 keV, ion temperature 0.8 keV and n tau 10 18 -- 10 19 sec/m 3 . Plasma confining magnetic fields are produced by the helical coil current. To assure the accuracy of the helical coils, the high level of accuracy was required to the profile of the vacuum chamber. The vacuum chamber twists around the torus by 9.5 times and its poloidal cross section shows a race-track shape in any toroidal position. Major radius is 2200 mm and minor radius is 215.5 mm. The material is the high-strength non-magnetic steel which has low permeability (μ = 40 kgf/mm 2 ) and special chemical composition (25Cr-12Ni-0.3N). The thickness of the wall is from 20 to 33 mm. To make the vacuum chamber, 190 pieces were joined together by EB welding after the hot press forming. A giant apparatus (6.5 m x 6.5 m x 3.5 m) was prepared and applied and a special re-focusing coil was used for the long beam welding. The profile accuracy of the vacuum chamber has been controlled as follows; major radius +-3 mm, minor radius sub(-1.5)sup(+4.5)mm, where minus means the inner side. X-ray and dye-penetrant quality of all welds was acceptable for ASME pressure vessel code and JIS. The laekage was less than 1.3 x 10 -8 Torr. 1/sec. The final pressure is 2 x 10 -8 Torr. (author)

The Body as a Tool: Professional Classical Ballet Dancers' Embodiment

Science.gov (United States)

Alexias, George; Dimitropoulou, Elina

2011-01-01

This article is a qualitative study, which adopts the approach of social construction in order to comprehend the role played by the body in the formation of social behaviour. Using the concept of embodiment, professional ballet dancers have been chosen in order to investigate the particular attitude they form towards their bodies. The use of their…

Macrophage conditioned medium induced cellular network formation in MCF-7 cells through enhanced tunneling nanotube formation and tunneling nanotube mediated release of viable cytoplasmic fragments

International Nuclear Information System (INIS)

Patheja, Pooja; Sahu, Khageswar

2017-01-01

Infiltrating macrophages in tumor microenvironment, through their secreted cytokines and growth factors, regulate several processes of cancer progression such as cancer cell survival, proliferation, invasion, metastasis and angiogenesis. Recently, intercellular cytoplasmic bridges between cancer cells referred as tunneling nanotubes (TNTs) have been recognized as novel mode of intercellular communication between cancer cells. In this study, we investigated the effect of inflammatory mediators present in conditioned medium derived from macrophages on the formation of TNTs in breast adenocarcinoma cells MCF-7. Results show that treatment with macrophage conditioned medium (MφCM) not only enhanced TNT formation between cells but also stimulated the release of independently migrating viable cytoplasmic fragments, referred to as microplasts, from MCF-7 cells. Time lapse microscopy revealed that microplasts were released from parent cancer cells in extracellular space through formation of TNT-like structures. Mitochondria, vesicles and cytoplasm could be transferred from parent cell body to microplasts through connecting TNTs. The microplasts could also be resorbed into the parent cell body by retraction of the connecting TNTs. Microplast formation inhibited in presence cell migration inhibitor, cytochalasin-B. Notably by utilizing migratory machinery within microplasts, distantly located MCF-7 cells formed several TNT based intercellular connections, leading to formation of physically connected network of cells. Together, these results demonstrate novel role of TNTs in microplast formation, novel modes of TNT formation mediated by microplasts and stimulatory effect of MφCM on cellular network formation in MCF-7 cells mediated through enhanced TNT and microplast formation.

Macrophage conditioned medium induced cellular network formation in MCF-7 cells through enhanced tunneling nanotube formation and tunneling nanotube mediated release of viable cytoplasmic fragments

Energy Technology Data Exchange (ETDEWEB)

Patheja, Pooja, E-mail: pooja.patheja8@gmail.com [Laser Biomedical Applications Section, Raja Ramanna Centre for Advanced Technology, Indore 452013, Madhya Pradesh (India); Homi Bhabha National Institute, Training School Complex, Anushaktinagar, Mumbai 400094, Maharashtra (India); Sahu, Khageswar [Laser Biomedical Applications Section, Raja Ramanna Centre for Advanced Technology, Indore 452013, Madhya Pradesh (India)

2017-06-15

Infiltrating macrophages in tumor microenvironment, through their secreted cytokines and growth factors, regulate several processes of cancer progression such as cancer cell survival, proliferation, invasion, metastasis and angiogenesis. Recently, intercellular cytoplasmic bridges between cancer cells referred as tunneling nanotubes (TNTs) have been recognized as novel mode of intercellular communication between cancer cells. In this study, we investigated the effect of inflammatory mediators present in conditioned medium derived from macrophages on the formation of TNTs in breast adenocarcinoma cells MCF-7. Results show that treatment with macrophage conditioned medium (MφCM) not only enhanced TNT formation between cells but also stimulated the release of independently migrating viable cytoplasmic fragments, referred to as microplasts, from MCF-7 cells. Time lapse microscopy revealed that microplasts were released from parent cancer cells in extracellular space through formation of TNT-like structures. Mitochondria, vesicles and cytoplasm could be transferred from parent cell body to microplasts through connecting TNTs. The microplasts could also be resorbed into the parent cell body by retraction of the connecting TNTs. Microplast formation inhibited in presence cell migration inhibitor, cytochalasin-B. Notably by utilizing migratory machinery within microplasts, distantly located MCF-7 cells formed several TNT based intercellular connections, leading to formation of physically connected network of cells. Together, these results demonstrate novel role of TNTs in microplast formation, novel modes of TNT formation mediated by microplasts and stimulatory effect of MφCM on cellular network formation in MCF-7 cells mediated through enhanced TNT and microplast formation.

MODELING PLANETARY SYSTEM FORMATION WITH N-BODY SIMULATIONS: ROLE OF GAS DISK AND STATISTICS COMPARED TO OBSERVATIONS

International Nuclear Information System (INIS)

Liu Huigen; Zhou Jilin; Wang Su

2011-01-01

During the late stage of planet formation, when Mars-sized cores appear, interactions among planetary cores can excite their orbital eccentricities, accelerate their merging, and thus sculpt their final orbital architecture. This study contributes to the final assembling of planetary systems with N-body simulations, including the type I or II migration of planets and gas accretion of massive cores in a viscous disk. Statistics on the final distributions of planetary masses, semimajor axes, and eccentricities are derived and are comparable to those of the observed systems. Our simulations predict some new orbital signatures of planetary systems around solar mass stars: 36% of the surviving planets are giant planets (>10 M + ). Most of the massive giant planets (>30 M + ) are located at 1-10 AU. Terrestrial planets are distributed more or less evenly at J in highly eccentric orbits (e > 0.3-0.4). The average eccentricity (∼0.15) of the giant planets (>10 M + ) is greater than that (∼0.05) of the terrestrial planets ( + ). A planetary system with more planets tends to have smaller planet masses and orbital eccentricities on average.

Vortex matter stabilized by many-body interactions

Science.gov (United States)

Wolf, S.; Vagov, A.; Shanenko, A. A.; Axt, V. M.; Aguiar, J. Albino

2017-10-01

This work investigates interactions of vortices in superconducting materials between standard types I and II, in the domain of the so-called intertype (IT) superconductivity. Contrary to common expectations, the many-body (many-vortex) contribution is not a correction to the pair-vortex interaction here but plays a crucial role in the formation of the IT vortex matter. In particular, the many-body interactions stabilize vortex clusters that otherwise could not exist. Furthermore, clusters with large numbers of vortices become more stable when approaching the boundary between the intertype domain and type I. This indicates that IT superconductors develop a peculiar unconventional type of the vortex matter governed by the many-body interactions of vortices.

Retrogressively in-situ ore body chemical mining system and method

International Nuclear Information System (INIS)

Jacoby, C.H.

1981-01-01

A method is provided for mining a horizontal ore body lying underneath an overburden that precludes the use of other mining methods. Such an overburden may comprise a body of water, an inhabited area, or a geological formation that is difficult to penetrate. A vertical shaft is sunk in a convenient location, and at least two boreholes are drilled in a horizontal direction extending outwards from the shaft. The boreholes ae roughly parallel, but sloped in such a way as to facilitate the flow of a leaching solution along them. The formation lying between the boreholes is fractured to make it permeable to the leaching solution, and the solution is injected through one hole and recovered through the other. Different zones of the ore body may be fractured successively, starting with the most distant. It is desirable to backfill depleted zones with an inert waste material, cement, or other filler

Daphnia diversity in water bodies of the Po River Basin

Czech Academy of Sciences Publication Activity Database

Marková, Silvia; Maurone, C.; Racchetti, E.; Bartoli, M.; Rossi, V.

2017-01-01

Roč. 76, č. 2 (2017), s. 261-271 ISSN 1129-5767 Institutional support: RVO:67985904 Keywords : genetic diagnostic markers * invasive species * genetic differentiation Subject RIV: EB - Genetics ; Molecular Biology OBOR OECD: Biology (theoretical, mathematical, thermal, cryobiology, biological rhythm), Evolutionary biology Impact factor: 1.451, year: 2016

Numerical investigation of influence thermal preparation coal on nitric oxides formation in combustion process

Energy Technology Data Exchange (ETDEWEB)

Chernetskaya, N. [Siberian Federal Univ., Krasnoyarsk (Russian Federation); Chernetsky, M.; Dekterev, A. [Siberian Federal Univ., Krasnoyarsk (Russian Federation); Kutateladze Institute of Thermophysics, Novosibirsk (Russian Federation)

2013-07-01

Emissions of nitrogen oxides from coal combustion are a major environmental problem because they have been shown to contribute to the formation of acid rain and photochemical smog. Coal thermalpreparation before furnace delivery is effective method to reduce NOx emissions, shown by experiments in small-scale facilities (Babiy VI, Alaverdov PI, Influence of thermal preparation pulverized coal on nitric oxides outlet for combustion different metamorphized coal. ATI, 1983). This paper presents the mathematical model of burning thermal preparation coal. Validation of the model was carried out on laboratory-scale plant of All-Russia thermal engineering institute. Modeling of low-emissive burner with preliminary heating coal dust is made for the purpose of search of burner optimal constructions which provides low concentration of nitric oxides in the boiler. For modeling are used in-house CFD code ''{sigma}Flow'' (Dekterev AA, Gavrilov AA, Harlamov EB, Litvintcev KY, J Comput Technol 8(Part 1):250-255, 2003).

Marketingový výzkum spokojenosti zákazníka v oblasti služeb B2B

OpenAIRE

Vlčková, Michaela

2014-01-01

Diplomová práce se zaměřuje na problematiku nového marketingového odvětví zákaznické zkušenosti, a to v oblasti telekomunikačních služeb B2B. Teoretická část mapuje, zpracovává a shrnuje základní pojmy a informace z literárních zdrojů týkajících se téma spokojenosti zákazníků. V analytické části práce jsou obecná teoretická východiska na základě zmapování teoretických poznatků a také interních údajů společnosti Vodafone Czech Republic použita pro přípravu marketingového výzkumu, doporučení a ...

The foreign body response: at the interface of surgery and bioengineering.

Science.gov (United States)

Major, Melanie R; Wong, Victor W; Nelson, Emily R; Longaker, Michael T; Gurtner, Geoffrey C

2015-05-01

The surgical implantation of materials and devices has dramatically increased over the past decade. This trend is expected to continue with the broadening application of biomaterials and rapid expansion of aging populations. One major factor that limits the potential of implantable materials and devices is the foreign body response, an immunologic reaction characterized by chronic inflammation, foreign body giant cell formation, and fibrotic capsule formation. The English literature on the foreign body response to implanted materials and devices is reviewed. Fibrotic encapsulation can cause device malfunction and dramatically limit the function of an implanted medical device or material. Basic science studies suggest a role for immune and inflammatory pathways at the implant-host interface that drive the foreign body response. Current strategies that aim to modulate the host response and improve construct biocompatibility appear promising. This review article summarizes recent basic science, preclinical, and clinicopathologic studies examining the mechanisms driving the foreign body response, with particular focus on breast implants and synthetic meshes. Understanding these molecular and cellular mechanisms will be critical for achieving the full potential of implanted biomaterials to restore human tissues and organs.

Towards revealing the structure of bacterial inclusion bodies.

Science.gov (United States)

Wang, Lei

2009-01-01

Protein aggregation is a widely observed phenomenon in human diseases, biopharmaceutical production, and biological research. Protein aggregates are generally classified as highly ordered, such as amyloid fibrils, or amorphous, such as bacterial inclusion bodies. Amyloid fibrils are elongated filaments with diameters of 6-12 nm, they are comprised of residue-specific cross-beta structure, and display characteristic properties, such as binding with amyloid-specific dyes. Amyloid fibrils are associated with dozens of human pathological conditions, including Alzheimer disease and prion diseases. Distinguished from amyloid fibrils, bacterial inclusion bodies display apparent amorphous morphology. Inclusion bodies are formed during high-level recombinant protein production, and formation of inclusion bodies is a major concern in biotechnology. Despite of the distinctive morphological difference, bacterial inclusion bodies have been found to have some amyloid-like properties, suggesting that they might contain structures similar to amyloid-like fibrils. Recent structural data further support this hypothesis, and this review summarizes the latest progress towards revealing the structural details of bacterial inclusion bodies.

Presentation of an ingested foreign body as a vesical calculus: a ...

African Journals Online (AJOL)

Vesical calculus is a common entity in children of developing countries. Foreign body ingestion is a common occurrence in the pediatric population. An ingested foreign body eroding into the urinary bladder and leading to the formation of a vesical calculus is an extremely rare condition. We encountered a 14-year-old girl ...

Filter paper inhibits in vitro protocorm-like body formation in hybrid Cymbidium and reduces synseed germination, but buffers the negative impact of antibiotics

Directory of Open Access Journals (Sweden)

TEIXEIRA DA SILVA JAIME A.

2014-06-01

Full Text Available Only few studies in the plant tissue culture literature have examined the impact of filter paper on in vitro plant organogenesis. In this study, using a model plant, hybrid Cymbidium Twilight Moon ‘Day Light’, the impact of a single or double layer of Advantec #2 or Whatman #1 filter paper on new protocorm-like body (neo-PLB formation on Teixeira Cymbidium (TC medium was examined for half-PLBs (transgenic and non-transgenic, PLB-derived transverse thin cell layers (tTCLs, and PLB synseeds. In addition, the response of half-PLBs or tTCLs to two antibiotics (kanamycin and cefotaxime, commonly used in plant genetic transformation studies was investigated either directly on gelled medium or on filter paper-overlaid medium. Filter paper negatively affected most growth and developmental parameters of all the explants tested, both transgenic and non-transgenic. A double sheet of filter paper had a significantly (P ≤ 0.05 more negative impact than a single sheet, relative to the control values (i.e., no filter paper. Kanamycin inhibited neo-PLB formation on TC medium, the negative impact being greater on a single layer than on a double layer of filter paper, i.e., filter paper buffered the growth-inhibiting characteristics of kanamycin. Up to 100 mg/l, cefotaxime showed no apparent negative effects on neo-PLBs formation and growth, although hyperhydricity was observed when filter paper was not used.

Atomic Color Superfluid via Three-Body Loss

International Nuclear Information System (INIS)

Kantian, A.; Diehl, S.; Zoller, P.; Daley, A. J.; Dalmonte, M.; Hofstetter, W.

2009-01-01

Large three-body loss rates in a three-component Fermi gas confined in an optical lattice can dynamically prevent atoms from tunneling so as to occupy a lattice site with three atoms. This effective constraint not only suppresses the occurrence of actual loss events, but stabilizes BCS-pairing phases by suppressing the formation of trions. We study the effect of the constraint on the many-body physics using bosonization and density matrix renormalization group techniques, and also investigate the full dissipative dynamics including loss for the example of 6 Li.

Intermittent Hypoxia-Induced Carotid Body Chemosensory Potentiation and Hypertension Are Critically Dependent on Peroxynitrite Formation

Directory of Open Access Journals (Sweden)

Esteban A. Moya

2016-01-01

Full Text Available Oxidative stress is involved in the development of carotid body (CB chemosensory potentiation and systemic hypertension induced by chronic intermittent hypoxia (CIH, the main feature of obstructive sleep apnea. We tested whether peroxynitrite (ONOO−, a highly reactive nitrogen species, is involved in the enhanced CB oxygen chemosensitivity and the hypertension during CIH. Accordingly, we studied effects of Ebselen, an ONOO− scavenger, on 3-nitrotyrosine immunoreactivity (3-NT-ir in the CB, the CB chemosensory discharge, and arterial blood pressure (BP in rats exposed to CIH. Male Sprague-Dawley rats were exposed to CIH (5% O2, 12 times/h, 8 h/day for 7 days. Ebselen (10 mg/kg/day was administrated using osmotic minipumps and BP measured with radiotelemetry. Compared to the sham animals, CIH-treated rats showed increased 3-NT-ir within the CB, enhanced CB chemosensory responses to hypoxia, increased BP response to acute hypoxia, and hypertension. Rats treated with Ebselen and exposed to CIH displayed a significant reduction in 3-NT-ir levels (60.8 ± 14.9 versus 22.9 ± 4.2 a.u., reduced CB chemosensory response to 5% O2 (266.5 ± 13.4 versus 168.6 ± 16.8 Hz, and decreased mean BP (116.9 ± 13.2 versus 82.1 ± 5.1 mmHg. Our results suggest that CIH-induced CB chemosensory potentiation and hypertension are critically dependent on ONOO− formation.

Structure formation by a fifth force: N-body versus linear simulations