WorldWideScience

Sample records for board level drop

  1. Development of Drop/Shock Test in Microelectronics and Impact Dynamic Analysis for Uniform Board Response

    Science.gov (United States)

    Kallolimath, Sharan Chandrashekar

    For the past several years, many researchers are constantly developing and improving board level drop test procedures and specifications to quantify the solder joint reliability performance of consumer electronics products. Predictive finite element analysis (FEA) by utilizing simulation software has become widely acceptable verification method which can reduce time and cost of the real-time test process. However, due to testing and metrological limitations it is difficult not only to simulate exact drop condition and capture critical measurement data but also tedious to calibrate the system to improve test methods. Moreover, some of the important ever changing factors such as board flexural rigidity, damping, drop height, and drop orientation results in non-uniform stress/strain distribution throughout the test board. In addition, one of the most challenging tasks is to quantify uniform stress and strain distribution throughout the test board and identify critical failure factors. The major contributions of this work are in the four aspects of the drop test in electronics as following. First of all, an analytical FEA model was developed to study the board natural frequencies and responses of the system with the consideration of dynamic stiffness, damping behavior of the material and effect of impact loading condition. An approach to find the key parameters that affect stress and strain distributions under predominate mode responses was proposed and verified with theoretical solutions. Input-G method was adopted to study board response behavior and cut boundary interpolation methods was used to analyze local model solder joint stresses with the development of global/local FEA model in ANSYS software. Second, no ring phenomenon during the drop test was identified theoretically when the test board was modeled as both discrete system and continuous system. Numerical analysis was then conducted by FEA method for detailed geometry of attached chips with solder

  2. Hydraulic geometry of cohesive channels undergoing base level drop

    Science.gov (United States)

    Vachtman, Dina; Laronne, Jonathan B.

    2013-09-01

    This study extends earlier contributions on dynamic adjustments of fluvial channels to base level changes. We have investigated an in situ response of self-formed cohesive channels to a base level drop, conditions analogous to a gradual change in uplift and/or climate. Empirical hydraulic geometry equations for clayey-cohesive natural streams are presented using data from eight channels draining perennial brackish springs and discharge into the Dead Sea. Investigation of downstream variations in gradient and stream power relations suggests existence of three distinct reaches in which channel adjustment to base level drop is shared inequitably among hydraulic geometry variables. Values of the flow velocity exponent m are low (0.11 ≤ m ≤ 0.24), the mid-channel reach having the lowest exponent. The depth exponent f has the lowest value (f ≈ 0.3) for the uppermost channel reaches, the rest having higher values (f ≈ 0.4). The smallest width exponent (b = 0.35) characterizes the upper reaches. These values and their spatial distribution exhibit a regular pattern. We show that the lowermost channel reach adjusts by profile steepening and channel narrowing (f > b); the prevailing mechanism in the mid-channel reaches is lateral (width) adjustment, cross sections transiently transforming toward equilibrium; the uppermost reaches have wide and shallow channel cross sections because of series of bank collapses and resultant sediment aggradation, bringing rise to decreased local gradient, forcing further channel widening. The results of this study not only allow inference about how cohesive channels regulate their geometry, but also reveal the means by which hydraulic forces overcome substrate resistance, adjusting slope and channel dimensions and, as such, have implication for reach-scale channel morphology and models of stream power.

  3. Board task performance: An exploration of micro- and macro-level determinants of board effectiveness

    Science.gov (United States)

    Minichilli, Alessandro; Zattoni, Alessandro; Nielsen, Sabina; Huse, Morten

    2012-01-01

    This paper addresses recent calls to narrow the micro–macro gap in management research (Bamberger, 2008), by incorporating a macro-level context variable (country) in exploring micro-level determinants of board effectiveness. Following the integrated model proposed by Forbes and Milliken (1999), we identify three board processes as micro-level determinants of board effectiveness. Specifically, we focus on effort norms, cognitive conflicts and the use of knowledge and skills as determinants of board control and advisory task performance. Further, we consider how two different institutional settings influence board tasks, and how the context moderates the relationship between processes and tasks. Our hypotheses are tested on a survey-based dataset of 535 medium-sized and large industrial firms in Italy and Norway, which are considered to substantially differ along legal and cultural dimensions. The findings show that: (i) Board processes have a larger potential than demographic variables to explain board task performance; (ii) board task performance differs significantly between boards operating in different contexts; and (iii) national context moderates the relationships between board processes and board task performance. Copyright © 2010 John Wiley & Sons, Ltd. PMID:23365485

  4. Kinetic and kinematic adjustments during perturbed walking across visible and camouflaged drops in ground level.

    Science.gov (United States)

    Müller, Roy; Tschiesche, Kevin; Blickhan, Reinhard

    2014-07-18

    Walking in even the most familiar environment posesses a challenge to humans due to continuously changing surface conditions such as compliance, slip, or level. These changes can be visible or invisible due to camouflage. In order to prevent falling, camouflaged changes in the ground level in particular require a quick response of the locomotor system. For ten subjects we investigated kinematics and ground reaction forces of two consecutive contacts while they were walking across visible (drops of 0, -5 and -10 cm at second contact) and camouflaged (drops of 0 or -5 cm, and drops of 0 or -10 cm at second contact) changes in the ground level. For both situations we found significant kinetic and kinematic adjustments during the perturbed second contact but also one step earlier, in the preparatory first contact. During walking across visible changes in the ground level, second peak ground reaction force at first contact decreased whereas the drop height increased at the second contact. In addition, at the end of this first contact the ankle and knee were more flexed and the trunk was more erect compared to level walking. During the perturbed second contact, first peak ground reaction force increased with drop height, whereas kinematic adjustments at touchdown were less. The visual perception of the perturbation facilitated prior adaptations. During walking across camouflaged changes in ground level such a visually guided preadaptation was not possible and the adaptations prior to the perturbation were less than those observed during walking across visible changes in the ground. However, when stepping into a camouflaged drop, the kinetic and kinematic adjustments became more obvious and they increased with increasing camouflaged drop height. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. The Board's advice on Emergency Reference Levels of dose

    International Nuclear Information System (INIS)

    Clarke, R.H.; Webb, G.A.M.

    1981-01-01

    An outline review is presented of the development by the M.R.C. and N.R.P.B. of radiological criteria recommended for the limitation of the radiation exposure of members of the public resulting from unplanned discharges of radioactive materials in the U.K.. The Board's publication of its revised Emergency Reference Levels of dose is briefly discussed. The Board has recommended ranges of dose equivalent in respect of the introduction of each countermeasure. For each there is a level of dose equivalent at which consideration of the introduction of the countermeasure should begin. It is envisaged that when emergency plans are prepared for any reactor site, the operator will take responsibility, in consultation with the appropriate regulatory authorities, for setting site-specific Action Levels for the introduction of appropriate countermeasures. (U.K.)

  6. Where do international board members come from? Country-level antecedents of international board member selection in European boards

    NARCIS (Netherlands)

    van Veen, Kees; Sahib, Padma Rao; Aangeenbrug, Evelien

    In this paper, it is argued that boards internationalize by recruiting international directors in order to increase companies' performance. However, increasing nationality diversity on a board can be costly considering that it potentially creates cooperative problems on a board due to fault-lines

  7. Performance Appraisal of College-Level Learners Using Smart Boards

    Science.gov (United States)

    Riyaz, Reeja

    2010-01-01

    This article reports on the evaluation of the use of Smart Boards in learning and teaching second-language writing skills. Results showed that the use of Smart Boards in learning and teaching improved students' second-language skills.

  8. High speed bending of 2nd level interconnects on printed circuit boards for automotive electronics

    NARCIS (Netherlands)

    Kouters, M.H.M.; Ubachs, R.; Wiel, H.J. van de; Waal, A. van der; Veer, J. van der

    2011-01-01

    Standard drop tests for portable electronics are not representative for the qualification of automotive electronics. High-frequency vibrations are more dominant than abrupt shocks during normal operation. In this work a high speed board bending (HSB) method is developed to mimic the constant cyclic

  9. Knowledge-driven board-level functional fault diagnosis

    CERN Document Server

    Ye, Fangming; Chakrabarty, Krishnendu; Gu, Xinli

    2017-01-01

    This book provides a comprehensive set of characterization, prediction, optimization, evaluation, and evolution techniques for a diagnosis system for fault isolation in large electronic systems. Readers with a background in electronics design or system engineering can use this book as a reference to derive insightful knowledge from data analysis and use this knowledge as guidance for designing reasoning-based diagnosis systems. Moreover, readers with a background in statistics or data analytics can use this book as a practical case study for adapting data mining and machine learning techniques to electronic system design and diagnosis. This book identifies the key challenges in reasoning-based, board-level diagnosis system design and presents the solutions and corresponding results that have emerged from leading-edge research in this domain. It covers topics ranging from highly accurate fault isolation, adaptive fault isolation, diagnosis-system robustness assessment, to system performance analysis and evalua...

  10. NA62 Level 0 trigger: TELDES and InterTEL boards testing and integration scenario

    CERN Multimedia

    Lupi, Matteo

    2015-01-01

    TELDES is a TEL62 daughter-board used in the generation of the Liquid Krypton Calorimeter primitive for the Level 0 Trigger of the NA62 Experiment. InterTEL is a daughter-board used to interconnect the TEL62s used in the CEDAR, LAV and RICH detectors.

  11. Next level of board accountability in health care quality.

    Science.gov (United States)

    Pronovost, Peter J; Armstrong, C Michael; Demski, Renee; Peterson, Ronald R; Rothman, Paul B

    2018-03-19

    Purpose The purpose of this paper is to offer six principles that health system leaders can apply to establish a governance and management system for the quality of care and patient safety. Design/methodology/approach Leaders of a large academic health system set a goal of high reliability and formed a quality board committee in 2011 to oversee quality and patient safety everywhere care was delivered. Leaders of the health system and every entity, including inpatient hospitals, home care companies, and ambulatory services staff the committee. The committee works with the management for each entity to set and achieve quality goals. Through this work, the six principles emerged to address management structures and processes. Findings The principles are: ensure there is oversight for quality everywhere care is delivered under the health system; create a framework to organize and report the work; identify care areas where quality is ambiguous or underdeveloped (i.e. islands of quality) and work to ensure there is reporting and accountability for quality measures; create a consolidated quality statement similar to a financial statement; ensure the integrity of the data used to measure and report quality and safety performance; and transparently report performance and create an explicit accountability model. Originality/value This governance and management system for quality and safety functions similar to a finance system, with quality performance documented and reported, data integrity monitored, and accountability for performance from board to bedside. To the authors' knowledge, this is the first description of how a board has taken this type of systematic approach to oversee the quality of care.

  12. Report on the joint USA-Germany drop test program for a vitrified high level waste cask

    International Nuclear Information System (INIS)

    Golliher, K.G.; Witt, C.R.; Wieser, K.E.

    1993-01-01

    A series of full-scale drop tests was performed on a ductile iron transport cask in a cooperative program between the US Department of Energy (DOE) and Bundesantalt fuer Materialpruefung (BAM) in Germany. The tests, which were performed at BAM's test facility located near Lehre, Germany, were performed on a prototype cask designed for transport of Vitrified High Level Waste (VHLW) canisters. The VHLW cask is a right circular cylinder with a diameter of 1156 mm and a height of 3454 cm, and weighs approximately 24.6 kg including its payload of a single VHLW canister. The drop tests were performed with a non-radioactive, prototype VHLW canister in the cavity. (J.P.N.)

  13. A system level boundary scan controller board for VME applications [to CERN experiments

    CERN Document Server

    Cardoso, N; Da Silva, J C

    2000-01-01

    This work is the result of a collaboration between INESC and LIP in the CMS experiment being conducted at CERN. The collaboration addresses the application of boundary scan test at system level namely the development of a VME boundary scan controller (BSC) board prototype and the corresponding software. This prototype uses the MTM bus existing in the VME64* backplane to apply the 1149.1 test vectors to a system composed of nineteen boards, called here units under test (UUTs). A top-down approach is used to describe our work. The paper begins with some insights about the experiment being conducted at CERN, proceed with system level considerations concerning our work and with some details about the BSC board. The results obtained so far and the proposed work is reviewed in the end of this contribution. (11 refs).

  14. Level-1 Data Driver Card - A high bandwidth radiation tolerant aggregator board for detectors

    CERN Document Server

    Gkountoumis, Panagiotis; The ATLAS collaboration

    2017-01-01

    The Level-1 Data Driver Card (L1DDC) was designed for the needs of the future upgrades of the innermost stations of the ATLAS end-cap muon spectrometer. The L1DDC is a high speed aggregator board capable of communicating with multiple front-end electronic boards. It collects the Level-1 data along with monitoring data and transmits them to a network interface through bidirectional and/or unidirectional fiber links at 4.8 Gbps each. In addition, the L1DDC board distributes trigger, time and configuration data coming from the network interface to the front-end boards. The L1DDC is fully compatible with the Phase II upgrade where the trigger rate is expected to reach the 1 MHz. Three different types of L1DDC boards will be fabricated handling up to 10.080 Gbps of user data. It consist of custom made radiation tolerant ASICs: the GigaBit Transceiver (GBTx), the FEAST DC-DC converter, the Slow Control Adapter (SCA), and the Versatile Tranceivers (VTRX) and transmitters (VTTX). The overall scheme of the data acquis...

  15. Board national diversity and firm-level innovativeness within the European Union

    DEFF Research Database (Denmark)

    Habersetzer, Antoine; Makkonen, Teemu; Williams, Allan

    2017-01-01

    It has become increasingly commonplace for firms to have foreign-born persons in their board of directors. This has been frequently linked to increasing firm-level innovativeness. Surprisingly, there is no empirical evidence to corroborate or contradict this assumption. The analyses conducted here...

  16. Board national diversity and firm-level innovativeness within the European Union

    DEFF Research Database (Denmark)

    Habersetzer, Antoine; Makkonen, Teemu; Williams, Allan

    2017-01-01

    It has become increasingly commonplace for firms to have foreign-born persons in their board of directors. This has been frequently linked to increasing firm-level innovativeness. Surprisingly, there is no empirical evidence to corroborate or contradict this assumption. The analyses conducted her...

  17. Board Level Proton Testing Book of Knowledge for NASA Electronic Parts and Packaging Program

    Science.gov (United States)

    Guertin, Steven M.

    2017-01-01

    This book of knowledge (BoK) provides a critical review of the benefits and difficulties associated with using proton irradiation as a means of exploring the radiation hardness of commercial-off-the-shelf (COTS) systems. This work was developed for the NASA Electronic Parts and Packaging (NEPP) Board Level Testing for the COTS task. The fundamental findings of this BoK are the following. The board-level test method can reduce the worst case estimate for a board's single-event effect (SEE) sensitivity compared to the case of no test data, but only by a factor of ten. The estimated worst case rate of failure for untested boards is about 0.1 SEE/board-day. By employing the use of protons with energies near or above 200 MeV, this rate can be safely reduced to 0.01 SEE/board-day, with only those SEEs with deep charge collection mechanisms rising this high. For general SEEs, such as static random-access memory (SRAM) upsets, single-event transients (SETs), single-event gate ruptures (SEGRs), and similar cases where the relevant charge collection depth is less than 10 µm, the worst case rate for SEE is below 0.001 SEE/board-day. Note that these bounds assume that no SEEs are observed during testing. When SEEs are observed during testing, the board-level test method can establish a reliable event rate in some orbits, though all established rates will be at or above 0.001 SEE/board-day. The board-level test approach we explore has picked up support as a radiation hardness assurance technique over the last twenty years. The approach originally was used to provide a very limited verification of the suitability of low cost assemblies to be used in the very benign environment of the International Space Station (ISS), in limited reliability applications. Recently the method has been gaining popularity as a way to establish a minimum level of SEE performance of systems that require somewhat higher reliability performance than previous applications. This sort of application of

  18. Pressure Drop

    Science.gov (United States)

    Lawson, Mike

    2010-01-01

    Mike Lawson briefly discussed pressure drop for aerospace applications and presented short stories about adventures experienced while working at NASA and General Dynamics, including exposure to technologies like the Crew and Equipment Translation Aid (CETA) cart and the SWME.

  19. Foot Drop

    Science.gov (United States)

    ... is being done? The National Institute of Neurological Disorders and Stroke (NINDS) conducts research related to the neurological conditions that cause foot drop in its laboratories at the National ...

  20. Comparison of ground reaction forces during the Basic Step on the Core Board platform at various levels of stability.

    Science.gov (United States)

    Karczewska, Magdalena; Madej, Anna; Sadowska, Aleksandra; Mastalerz, Andrzej; Urbanik, Czesław

    2016-01-01

    The aim of this paper was to examine and compare the changes of ground reaction forces observed during the Basic Step on the Core Board fitness device at various levels of stability. The study involved 10 female students. Participants stepped on and off the Core Board 10 times at 3 levels of stability. After completing a series of steps, the Core Board's stability was modified and the participant repeated the whole series. The measurement platform to examine three components of the reaction force (horizontal in the sagittal and frontal planes, and vertical) was used. The ground reaction force (GRF) observed on the Core Board, in the vertical and horizontal components is higher at all three levels of stability than on the platform without the device. Significant differences in GRF were observed in the horizontal component in the frontal plane (Fz) at all three levels of mobility as well as in impulse, measured on platforms with the device. The results on the Core Board training device present highest horizontal ground reaction forces in frontal plane at the highest level of Core Board mobility and this showing little medio-lateral stability and a more reactive way of movement regulation of the participants. As a consequence of the force patterns found it may be suggested that fitness training concepts should focus more possibly higher strains on the locomotor system most likely caused by changed ground reaction force patterns, an idea that has to be further analyzed with more complex measurement approaches.

  1. Low-level software for the pentek 6510 digital receiver board applied to the new AD beam measurement system

    CERN Document Server

    Angoletta, Maria Elena

    2002-01-01

    The new beam measurement system for the CERN Antiproton Decelerator heavily relies on a Pentek 6510 Digital Receiver (DRX) board. The new system goal is to extract beam parameters from pickup signals. Its digital implementation allows for higher precision, easier management of the hardware as well as modification and improvement with no hardware change. In this scheme, this innovative VME DRX board is responsible for parallel data acquisition, independent digital down conversion and processing of up to 4 digitised inputs. The in-house- developed low-level code (LLC), running on the board, takes care of several tasks, such as interfacing with the Real Time Task (RTT), data processing and board managing. The RTT runs on a PowerPC VME board and controls the DRX board as a master. The LLC is a state machine developed in C and Assembler, which services several interrupts and performs the FFT of complex input data. The DRX low-level system developed is highly modular and easily adaptable to other processing scenari...

  2. The 'F.E.E.L.' good factors in nursing leadership at board level through work-based learning.

    Science.gov (United States)

    Jumaa, Mansour Olawale

    2008-11-01

    The aim of this commentary is to raise awareness about the apparent lack of formal activities and the paucity of published papers in nursing leadership development at the board level in the United Kingdom (UK). The paper suggests a way forward. The author has been serving at a board level, within and outside of nursing, locally, nationally and internationally since 1988. His current experience as an active board member and honorary treasurer of a leading charity organization in the Southeast of England and participation on a Board Leadership Development programme in the United States of America (USA) led to the need to write this commentary. Leadership at the board level is different because the board is the governing body of an organization. The board has overall responsibility for running the organization. The overall duty is to manage less and LEAD more. The need for this type of leadership is on the increase because these are turbulent days in the healthcare industry. This growing trend witnesses increasing and greater demand from key stakeholders for nursing and healthcare services: rising exposure to liability and litigation; a demand for stronger accountability and questioning of the nature and delivery of nursing and healthcare services. Effective and successful leadership judgment is made based on both numbers [efficient resources utilization (RU)] and stories [effective client/patient satisfaction (CS)]. Nurses and others in the healthcare industry need to guide against the leadership myths that: 'everyone can be a leader'; 'leaders deliver business (service) results'; 'people who get to the top are leaders'; and 'that leaders are great coaches'. This commentary demonstrates these myths could be converted to become realities through developing and possessing most if not all the knowledge, skills and attitudes implicated in the Effective Board Leadership Capabilities Development Profile presented in this paper. Possessing board level leadership

  3. Digital Board Game: Is there a need for it in language learning among tertiary level students?

    Directory of Open Access Journals (Sweden)

    Ali Zuraina

    2018-01-01

    Full Text Available The concept of learning while playing to learn language is a pedagogy that can enhance students’ learning interest. In this digital era, the use of board games, for instance, has provided a solution to learning a language. A considerable literature has grown up around the theme of digital board in language learning. Therefore, this paper aims at finding the significance of developing a digital board game for the purpose of vocabulary learning. Fifty-seven (57 students from Universiti Malaysia Pahang (UMP were selected as samples using purposive random sampling to collect data for the current study. A questionnaire was employed to explore their needs of a digital board game to learn vocabulary. The findings revealed that digital board game has significant needs among students to learn vocabulary, and further support the idea of using digital board game in language classroom. Majority of them believed that digital board game may provide a significant impact on vocabulary learning. Overall, the current study proves to be particularly valuable to language teachers to incorporate digital board game into their instructional activity. Also, these findings suggest a role for interactive learning in motivating language learner to enrich their vocabulary size.

  4. Acceleration levels on board the Space Station and a tethered elevator for micro and variable-gravity applications

    Science.gov (United States)

    Lorenzini, E. C.; Cosmo, M.; Vetrella, S.; Moccia, A.

    1988-01-01

    This paper investigates the dynamics and acceleration levels of a new tethered system for micro and variable-gravity applications. The system consists of two platforms tethered on opposite sides to the Space Station. A fourth platform, the elevator, is placed in between the Space Station and the upper platform. Variable-g levels on board the elevator are obtained by moving this facility along the upper tether, while micro-g experiments are carried out on board the Space Station. By controlling the length of the lower tether the position of the system CM can be maintained on board the Space Station despite variations of the station's distribution of mass. The paper illustrates the mathematical model, the environmental perturbations and the control techniques which have been adopted for the simulation and control of the system dynamics. Two sets of results from two different simulation runs are shown. The first set shows the system dynamics and the acceleration spectra on board the Space Station and the elevator during station-keeping. The second set of results demonstrates the capability of the elevator to attain a preselected g-level.

  5. Development and evaluation of a drop-and-stick method to assess landing skills in various levels of competitive surfers.

    Science.gov (United States)

    Tran, Tai T; Lundgren, Lina; Secomb, Josh; Farley, Oliver R; Haff, G Gregory; Newton, Robert U; Nimphius, Sophia; Sheppard, Jeremy M

    2015-04-01

    The purpose of this study was to develop and evaluate a drop-and-stick (DS) test method and to assess dynamic postural control in senior elite (SE), junior elite (JE), and junior development (JD) surfers. Nine SE, 22 JE, and 17 JD competitive surfers participated in a single testing session. The athletes completed 5 drop-and-stick trials barefoot from a predetermined box height (0.5 m). The lowest and highest time-to-stabilization (TTS) trials were discarded, and the average of the remaining trials was used for analysis. The SE group demonstrated excellent single-measures repeatability (ICC = .90) for TTS, whereas the JE and JD demonstrated good single-measures repeatability (ICC .82 and .88, respectively). In regard to relative peak landing force (rPLF), SE demonstrated poor single-measures reliability compared with JE and JD groups. Furthermore, TTS for the SE (0.69 ± 0.13 s) group was significantly (P = .04) lower than the JD (0.85 ± 0.25 s). There were no significant (P = .41) differences in the TTS between SE (0.69 ± 0.13 s) and JE (0.75 ± 0.16 s) groups or between the JE and JD groups (P = .09). rPLF for the SE (2.7 ± 0.4 body mass; BM) group was significantly lower than the JE (3.8 ± 1.3 BM) and JD (4.0 ± 1.1 BM), with no significant (P = .63) difference between the JE and JD groups. A possible benchmark approach for practitioners would be to use TTS and rPLF as a qualitative measure of dynamic postural control using a reference scale to discriminate among groups.

  6. Low-level determination of silicon in steels by anodic stripping voltammetry on a hanging mercury drop electrode.

    Science.gov (United States)

    Rahier, A H; Lunardi, S; Nicolle, F; George, S M

    2010-10-15

    The sensitive differential pulse anodic stripping voltammetry (DPASV) proposed originally by Ishiyama et al. (2001) has been revised and improved to allow the accurate measurement of silicon on a hanging mercury drop electrode (HMDE) instead of a glassy carbon electrode. We assessed the rate of formation of the partially reduced β-silicododecamolybdate and found that metallic mercury promotes the reaction in the presence of a large concentration of Fe(3+). The scope of the method has been broadened by carrying out the measurements in the presence of a constant amount of Fe(3+). The limit of detection (LOD) of the method described in the present paper is 100 μg Sig(-1) of steel, with a relative precision ranging from 5% to 12%. It can be further enhanced to 700 ng Sig(-1) of steel provided the weight of the sample, the dilution factors, the duration of the electrolysis and the ballast of iron are adequately revised. The tolerance to several interfering species has been examined, especially regarding Al(3+), Cr(3+) and Cr VI species. The method was validated using four low-alloy ferritic steels certified by the National Institute of Standards and Technology (NIST). Its application to nickel base alloys as well as to less complicated matrixes is straightforward. It has also been successfully applied to the determination of free silicon into silicon carbide nano-powder. Copyright © 2010 Elsevier B.V. All rights reserved.

  7. Does Parental Educational Level Predict Drop-Out from Upper Secondary School for 16- to 24-Year-Olds when Basic Skills Are Accounted For? A Cross Country Comparison

    Science.gov (United States)

    Lundetrae, Kjersti

    2011-01-01

    Drop-out from upper secondary school is considered a widespread problem, closely connected with youth unemployment. The aim of the current study was to examine whether parents' level of education predicted drop-out for 16-24-year-olds when accounting for basic skills. For this purpose, data from the Norwegian (n = 996) and American (n = 641)…

  8. When Do Companies Need a Board-Level Risk Management Committee?

    OpenAIRE

    Choi, Ivan

    2013-01-01

    Risk management is nothing new. But the global financial crisis and corporate failures in recent years have put risk management in the spotlight. Who is ultimately responsible for it? Responsibility for risk management should start in the boardroom, as the board is ultimately responsible for the organization's decision making, business performance, and value creation, all of which are asso...

  9. Assessing the Difficulty Level of Math Board Games for Young Children

    Science.gov (United States)

    Moomaw, Sally

    2015-01-01

    This study investigated differences in difficulty among three types of math board games used as curricular materials in some preschool classrooms. Difference in performance between low- and middle-income children on the three types of games was also explored. Children drew cards containing one to five large dots; they then attempted to place an…

  10. Teachers, School Boards, and the Power of Money: How the Right Wins at the Local Level

    Science.gov (United States)

    Schirmer, Eleni B.; Apple, Michael W.

    2016-01-01

    This article examines national conservative political advocacy groups' growing interest in local politics, and analyzes how they form alliances and gain political power. Following efforts to restrict collective bargaining for Wisconsin public employees, Kenosha school board members' attempts to legally protect teachers' rights provoked concern…

  11. Development of the new trigger processor board for the ATLAS Level-1 endcap muon trigger for Run-3

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00525035; The ATLAS collaboration

    2017-01-01

    The instantaneous luminosity of the LHC will be increased by up to a factor of three with respect to the original design value at Run-3 (starting 2021). The ATLAS Level-1 end-cap muon trigger in LHC Run-3 will identify muons by combining data from the Thin-Gap Chamber detector (TGC) and the New Small Wheel (NSW), which is a new detector and will be able to operate in a high background hit rate at Run-3, to suppress the Level-1 trigger rate. In order to handle data from both TGC and NSW, a new trigger processor board has been developed. The board has a modern FPGA to make use of Multi-Gigabit transceiver technology. The readout system for trigger data has also been designed with TCP/IP instead of a dedicated ASIC. This letter presents the electronics and its firmware of the ATLAS Level-1 end-cap muon trigger processor board for LHC Run-3.

  12. Online Teaching and Learning at the Graduate School Level: Student Perceptions on Discussion Boards v. Synchronous Communication

    Directory of Open Access Journals (Sweden)

    Christopher N. Amos Sr.

    2014-06-01

    Full Text Available This paper examines a group of graduate students and their previous experiences with online education, various teaching and learning online tools, and their perceptions on the effectiveness of these tools as it relates to their learning, interpersonal skills and communication. This paper presents the graduate student's self-reported educational experience at a regional state university in the southeast United States in a 100% online Master's Degree program. The data was collected through the use of a 28 open-ended question survey, which was completed by a group of 127 graduate students and the findings produced six main findings, which were: 1 The respondents indicated at a high percentage (85% a high level (level 4, 5 and 6 of technology use and understanding. 2 The majority of the respondents (97% indicated they preferred live synchronous sessions rather than discussion boards for learning content and communication. 3 The majority of the respondents (72% indicated that when choosing future courses, the inclusion of discussion boards in a course was not important (34% or somewhat unimportant (38%. 4 100% of the respondents indicated that Live Elluminate Sessions were Highly Effective (65% or Somewhat Effective (35%, as it pertained to understanding the content. 5 Respondents indicated that 59% (12% Highly Effective, 47% Somewhat Effective of the respondents indicated discussion boards as an impactful way of learning content at the graduate level. It also shows that 41% (22% Somewhat Ineffective, 19% Not Effective. This study helps universities identify the importance of synchronous learning in a digital format when delivering online teaching and learning. There is a clear change in the needs of students enrolled in 100% online courses, which will force university faculty to increase the synchronous interaction between them and their students and between the students and their peers. Keywords: Synchronous learning, discussion boards, Blackboard

  13. Dilating Eye Drops

    Science.gov (United States)

    ... Frequently Asked Questions Español Condiciones Chinese Conditions Dilating Eye Drops En Español Read in Chinese What are dilating eye drops? Dilating eye drops contain medication to enlarge ( ...

  14. Coalescence of a Drop inside another Drop

    Science.gov (United States)

    Mugundhan, Vivek; Jian, Zhen; Yang, Fan; Li, Erqiang; Thoroddsen, Sigurdur

    2016-11-01

    Coalescence dynamics of a pendent drop sitting inside another drop, has been studied experimentally and in numerical simulations. Using an in-house fabricated composite micro-nozzle, a smaller salt-water drop is introduced inside a larger oil drop which is pendent in a tank containing the same liquid as the inner drop. On touching the surface of outer drop, the inner drop coalesces with the surrounding liquid forming a vortex ring, which grows in time to form a mushroom-like structure. The initial dynamics at the first bridge opening up is quantified using Particle Image Velocimetry (PIV), while matching the refractive index of the two liquids. The phenomenon is also numerically simulated using the open-source code Gerris. The problem is fully governed by two non-dimensional parameters: the Ohnesorge number and the diameter ratios of the two drops. The validated numerical model is used to better understand the dynamics of the phenomenon. In some cases a coalescence cascade is observed with liquid draining intermittently and the inner drop reducing in size.

  15. ANALYSIS OF INTERDEPENDENCE BETWEEN ARRIVALS OF TOURISTS IN BOARDING HOUSES, ACCOMMODATION CAPACITY AND RELATIVE POVERTY RATE TO REGIONAL DEVELOPMENT LEVEL

    Directory of Open Access Journals (Sweden)

    GHIZDEANU ION

    2016-02-01

    Full Text Available Regardless of the activity area, the link between the firm, sustainability and the necessary means to achieve that desideratum, is real and accepted in the context in which scientists, investors, entrepreneurs, state and citizens are becoming more and more aware of the devastating impact of the chaotic activities aimed at making a profit at any cost. Being aware of the importance of the correlation between ecotourism and sustainability, after a preliminary conceptualization of the means to promote green tourism business, and some elements of ecological marketing an analysis has been attempted via the linear regression model of interdependence between arrivals of tourists in the rural boarding houses, accommodation capacity and the relative poverty rate at the level of development region in Romania. In this sense, the data provided by the National Institute of Statistics have been used.

  16. LEVEL-1 DATA DRIVER CARD - A high bandwidth radiation tolerant aggregator board for detectors

    CERN Document Server

    Gkountoumis, Panagiotis; The ATLAS collaboration

    2018-01-01

    The Level-1 Data Driver Card (L1DDC) was designed for the needs of the future upgrades of the innermost stations of the ATLAS end-cap muon spectrometer. The detectors located at the muon Small Wheels will be replaced by a set of precision tracking and trigger detectors, the resistive Micromegas (MM) and the small-strip Thin Gap Chambers (sTGC). After the upgrade, the number of interactions per bunch-crossing will be increased up to 140, resulting in a dramatically large amount of produced data. The high number of electronic channels (about two million for the MM and about 300k for the sTGC) along with a harsh environment (radiation dose up to 1700Gy (inner radius) and a magnetic field up to 0:4T in the end cap region) led to the development of new radiation tolerant electronics and a scalable readout scheme able to handle the new data rates. In addition, correction mechanisms for Single Event Upsets (SEU) and communication errors must be implemented to assure the integrity of the transmitted data. The L1DDC i...

  17. Scanning drop sensor

    Science.gov (United States)

    Jin, Jian; Xiang, Chengxiang; Gregoire, John M.; Shinde, Aniketa A.; Guevarra, Dan W.; Jones, Ryan J.; Marcin, Martin R.; Mitrovic, Slobodan

    2017-05-09

    Electrochemical or electrochemical and photochemical experiments are performed on a collection of samples by suspending a drop of electrolyte solution between an electrochemical experiment probe and one of the samples that serves as a test sample. During the electrochemical experiment, the electrolyte solution is added to the drop and an output solution is removed from the drop. The probe and collection of samples can be moved relative to one another so the probe can be scanned across the samples.

  18. Bubble and drop interfaces

    CERN Document Server

    Miller

    2011-01-01

    The book aims at describing the most important experimental methods for characterizing liquid interfaces, such as drop profile analysis, bubble pressure and drop volume tensiometry, capillary pressure technique, and oscillating drops and bubbles. Besides the details of experimental set ups, also the underlying theoretical basis is presented in detail. In addition, a number of applications based on drops and bubbles is discussed, such as rising bubbles and the very complex process of flotation. Also wetting, characterized by the dynamics of advancing contact angles is discussed critically. Spec

  19. Turbulence, bubbles and drops

    NARCIS (Netherlands)

    van der Veen, Roeland

    2016-01-01

    In this thesis, several questions related to drop impact and Taylor-Couette turbulence are answered. The deformation of a drop just before impact can cause a bubble to be entrapped. For many applications, such as inkjet printing, it is crucial to control the size of this entrapped bubble. To study

  20. Drop Tower Physics

    Science.gov (United States)

    Dittrich, William A. Toby

    2014-10-01

    The drop towers of yesteryear were used to make lead shot for muskets, as described in The Physics Teacher1 in April 2012. However, modern drop towers are essentially elevators designed so that the cable can "break" on demand, creating an environment with microgravity for a short period of time, currently up to nine seconds at the drop tower in Bremen, Germany. Using these drop towers, one can briefly investigate various physical systems operating in this near zero-g environment. The resulting "Drop Tower Physics" is a new and exciting way to challenge students with a physical example that requires solid knowledge of many basic physics principles, and it forces them to practice the scientific method. The question is, "How would a simple toy, like a pendulum, behave when it is suddenly exposed to a zero-g environment?" The student must then postulate a particular behavior, test the hypothesis against physical principles, and if the hypothesis conforms to these chosen physical laws, the student can formulate a final conclusion. At that point having access to a drop tower is very convenient, in that the student can then experimentally test his or her conclusion. The purpose of this discussion is to explain the response of these physical systems ("toys") when the transition is made to a zero-g environment and to provide video demonstrations of this behavior to support in-class discussions of Drop Tower Physics.

  1. Board Task Performance

    DEFF Research Database (Denmark)

    Minichilli, Alessandro; Zattoni, Alessandro; Nielsen, Sabina

    2012-01-01

    influence board tasks, and how the context moderates the relationship between processes and tasks. Our hypotheses are tested on a survey-based dataset of 535 medium-sized and large industrial firms in Italy and Norway, which are considered to substantially differ along legal and cultural dimensions...... identify three board processes as micro-level determinants of board effectiveness. Specifically, we focus on effort norms, cognitive conflicts and the use of knowledge and skills as determinants of board control and advisory task performance. Further, we consider how two different institutional settings...

  2. Board Charter

    International Development Research Centre (IDRC) Digital Library (Canada)

    TEST

    Senior Centre Staff participate in meetings and make presentations to allow. Governors to gain ... assist individual governors, part of the Board evaluation includes self-assessment. The Board. Evaluation ... oversee the Board's evaluation and self-assessment exercises and implementing change and improvements, as ...

  3. Predicting adult pulmonary ventilation volume and wearing complianceby on-board accelerometry during personal level exposure assessments

    Science.gov (United States)

    Rodes, C. E.; Chillrud, S. N.; Haskell, W. L.; Intille, S. S.; Albinali, F.; Rosenberger, M. E.

    2012-09-01

    BackgroundMetabolic functions typically increase with human activity, but optimal methods to characterize activity levels for real-time predictions of ventilation volume (l min-1) during exposure assessments have not been available. Could tiny, triaxial accelerometers be incorporated into personal level monitors to define periods of acceptable wearing compliance, and allow the exposures (μg m-3) to be extended to potential doses in μg min-1 kg-1 of body weight? ObjectivesIn a pilot effort, we tested: 1) whether appropriately-processed accelerometer data could be utilized to predict compliance and in linear regressions to predict ventilation volumes in real-time as an on-board component of personal level exposure sensor systems, and 2) whether locating the exposure monitors on the chest in the breathing zone, provided comparable accelerometric data to other locations more typically utilized (waist, thigh, wrist, etc.). MethodsPrototype exposure monitors from RTI International and Columbia University were worn on the chest by a pilot cohort of adults while conducting an array of scripted activities (all oral-nasal ventilation volumes in-situ. For the subset of participants with complete data (n = 22), linear regressions were constructed (processed accelerometric variable versus ventilation rate) for each participant and exposure monitor type, and Pearson correlations computed to compare across scenarios. ResultsTriaxial accelerometer data were demonstrated to be adequately sensitive indicators for predicting exposure monitor wearing compliance. Strong linear correlations (R values from 0.77 to 0.99) were observed for all participants for both exposure sensor accelerometer variables against ventilation volume for recumbent, sedentary, and ambulatory activities with MET values ˜<6. The RTI monitors mean R value of 0.91 was slightly higher than the Columbia monitors mean of 0.86 due to utilizing a 20 Hz data rate instead of a slower 1 Hz rate. A nominal mean

  4. Board game

    International Nuclear Information System (INIS)

    Brennan, N.S.

    1982-01-01

    A board game comprises a board, a number of counters and two dice. The board is marked to provide a central area, representing the nucleus of an atom, and six or more annular rings extending concentrically around the central area, the rings being divided into 2,8,18,32,48 and 72 squares. Each ring represents an electron shell, and some of the squares are numbered, the number representing the atomic number of different elements. (author)

  5. Drop Tower Facility at Queensland University of Technology

    Science.gov (United States)

    Plagens, Owen; Castillo, Martin; Steinberg, Theodore; Ong, Teng-Cheong

    The Queensland University of Technology (QUT) Drop Tower Facility is a {raise.17exscriptstyle˜}2.1 second, 21.3 m fall, dual capsule drop tower system. The dual capsule comprises of an uncoupled exterior hollow drag shield that experiences drag by the ambient atmosphere with the experimental capsule falling within the drag shield. The dual capsule system is lifted to the top of the drop tower via a mechanical crane and the dropping process is initiated by the cutting of a wire coupling the experimental package and suspending the drag shield. The internal experimental capsule reaches the bottom of the drag shield floor just prior to the deceleration stage at the air bag and during this time experience gravity levels of {raise.17exscriptstyle˜}10textsuperscript{-6} g. The deceleration system utilizes an inflatable airbag where experimental packages can be designed to experience a maximum deceleration of {raise.17exscriptstyle˜}10textsuperscript{18} g for {raise.17exscriptstyle˜}0.1 seconds. The drag shield can house experimental packages with a maximum diameter of 0.8 m and height of 0.9 m. The drag shield can also be used in foam mode, where the walls are lined with foam and small experiments can be dropped completely untethered. This mode is generally used for the study of microsatellite manipulation. Payloads can be powered by on-board power systems with power delivered to the experiment until free fall occurs. Experimental data that can be collected includes but is not limited to video, temperature, pressure, voltage/current from the power supply, and triggering mechanisms outputs which are simultaneously collected via data logging systems and high speed video recording systems. Academic and commercial projects are currently under investigation at the QUT Drop Tower Facility and collaboration is openly welcome at this facility. Current research includes the study of heterogeneously burning metals in oxygen which is aimed at fire safety applications and

  6. Impact of granular drops

    KAUST Repository

    Marston, J. O.

    2013-07-15

    We investigate the spreading and splashing of granular drops during impact with a solid target. The granular drops are formed from roughly spherical balls of sand mixed with water, which is used as a binder to hold the ball together during free-fall. We measure the instantaneous spread diameter for different impact speeds and find that the normalized spread diameter d/D grows as (tV/D)1/2. The speeds of the grains ejected during the “splash” are measured and they rarely exceed twice that of the impact speed.

  7. Large drops cause complete coalescence

    Indian Academy of Sciences (India)

    The thin film below the drop drains out slowly with time, finally creating a hole in the drop when it comes in contact with the interface at t=0.37 Tc, a small matrix drop, also called satellite drop, is seen to be trapped during the film rupture. Such an entrapment was observed by Thoroddsen et al (2008) and Chen et al (2006).

  8. Two secondary drops

    Indian Academy of Sciences (India)

    Figure shows formation of two secondary drops of unequal size and their merger. The process is same as the earlier process until t= 0.039 Tc with necking occurring at two places, one at the bottom of the column and the other at the middle. The necking at the middle of the liquid column is due to Raleigh instability.

  9. Two secondary drops

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Notes: Figure shows formation of two secondary drops of unequal size and their merger. The process is same as the earlier process until t= 0.039 Tc with necking occurring at two places, one at the bottom of the column and the other at the middle. The necking at the ...

  10. Lambda-dropping

    DEFF Research Database (Denmark)

    Danvy, Olivier; Schultz, Ulrik Pagh

    1997-01-01

    the parameters that any of their callees might possibly need. Both lambda-lifting and lambda-dropping thus require one to compute a transitive closure over the call graph:• for lambda-lifting: to establish the Def/Use path of each free variable (these free variables are then added as parameters to each......Lambda-lifting a functional program transforms it into a set of recursive equations. We present the symmetric transformation: lambda-dropping. Lambda-dropping a set of recursive equations restores block structure and lexical scope.For lack of scope, recursive equations must carry around all...... of the functions in the call path);• for lambda-dropping: to establish the Def/Use path of each parameter (parameters whose use occurs in the same scope as their definition do not need to be passed along in the call path).Without free variables, a program is scope-insensitive. Its blocks are then free...

  11. Predicting the Drop Performance of Solder Joints by Evaluating the Elastic Strain Energy from High-Speed Ball Pull Tests

    Science.gov (United States)

    You, Taehoon; Kim, Yunsung; Kim, Jina; Lee, Jaehong; Jung, Byungwook; Moon, Jungtak; Choe, Heeman

    2009-03-01

    Despite being expensive and time consuming, board-level drop testing has been widely used to assess the drop or impact resistance of the solder joints in handheld microelectronic devices, such as cellphones and personal digital assistants (PDAs). In this study, a new test method, which is much simpler and quicker, is proposed. The method involves evaluating the elastic strain energy and relating it to the impact resistance of the solder joint by considering the Young’s modulus of the bulk solder and the fracture stress of the solder joint during a ball pull test at high strain rates. The results show that solder joints can be ranked in order of descending elastic strain energy as follows: Sn-37Pb, Sn-1Ag-0.5Cu, Sn-3Ag-0.5Cu, and Sn-4Ag-0.5Cu. This order is consistent with the actual drop performances of the samples.

  12. Technology Readiness Level (TRL) Advancement of the MSPI On-Board Processing Platform for the ACE Decadal Survey Mission

    Science.gov (United States)

    Pingree, Paula J.; Werne, Thomas A.; Bekker, Dmitriy L.; Wilson, Thor O.

    2011-01-01

    The Xilinx Virtex-5QV is a new Single-event Immune Reconfigurable FPGA (SIRF) device that is targeted as the spaceborne processor for the NASA Decadal Survey Aerosol-Cloud-Ecosystem (ACE) mission's Multiangle SpectroPolarimetric Imager (MSPI) instrument, currently under development at JPL. A key technology needed for MSPI is on-board processing (OBP) to calculate polarimetry data as imaged by each of the 9 cameras forming the instrument. With funding from NASA's ESTO1 AIST2 Program, JPL is demonstrating how signal data at 95 Mbytes/sec over 16 channels for each of the 9 multi-angle cameras can be reduced to 0.45 Mbytes/sec, thereby substantially reducing the image data volume for spacecraft downlink without loss of science information. This is done via a least-squares fitting algorithm implemented on the Virtex-5 FPGA operating in real-time on the raw video data stream.

  13. Effects of a wobble board-based therapeutic exergaming system for balance training on dynamic postural stability and intrinsic motivation levels.

    Science.gov (United States)

    Fitzgerald, Diarmaid; Trakarnratanakul, Nanthana; Smyth, Barry; Caulfield, Brian

    2010-01-01

    Randomized controlled trial. To compare the effects of wobble board exercises with and without feedback provided through integrating the wobble board movement into a computer game system, by comparing changes in postural stability and motivation. Therapeutic exergaming systems may offer a solution to poor adherence to postural control exercise regimes by improving motivation levels during exercise performance. Twenty-two healthy adults, randomly assigned to an exergaming group (n = 11) and a control group (n = 11), completed 12 exercise sessions. Dynamic postural stability was quantified at baseline and follow-up using the star excursion balance test and the dynamic postural stability index during a jump-landing task. Intrinsic motivation was measured at baseline using the Self-Motivation Inventory and at follow-up using the Intrinsic Motivation Inventory. Star excursion balance test scores showed a statistically significant (PIntrinsic Motivation Inventory showed significantly higher scores (PIntrinsic Motivation Inventory categories evaluated. The findings suggest that exercising with the therapeutic exergaming system showed similar improvements in dynamic postural stability and showed a greater level of interest and enjoyment when compared to a group doing similar balance training without the game system. Therapy, level 2b.

  14. The Dutch 'Female Board Index' 2009

    NARCIS (Netherlands)

    Lückerath – Rovers, M.

    2009-01-01

    This report gives an overview of the presence of women in the Executive Board and Supervisory Board (together: 'the Board') of Dutch listed companies per September 2009. The companies have been ranked by the percentage women in the Board. A difference analysis has been made at personal level

  15. First drop dissimilarity in drop-on-demand inkjet devices

    International Nuclear Information System (INIS)

    Famili, Amin; Palkar, Saurabh A.; Baldy, William J. Jr.

    2011-01-01

    As inkjet printing technology is increasingly applied in a broader array of applications, careful characterization of its method of use is critical due to its inherent sensitivity. A common operational mode in inkjet technology known as drop-on-demand ejection is used as a way to deliver a controlled quantity of material to a precise location on a target. This method of operation allows ejection of individual or a sequence (burst) of drops based on a timed trigger event. This work presents an examination of sequences of drops as they are ejected, indicating a number of phenomena that must be considered when designing a drop-on-demand inkjet system. These phenomena appear to be driven by differences between the first ejected drop in a burst and those that follow it and result in a break-down of the linear relationship expected between driving amplitude and drop mass. This first drop, as quantified by high-speed videography and subsequent image analysis, can be different in morphology, trajectory, velocity, and volume from subsequent drops within a burst. These findings were confirmed orthogonally by both volume and mass measurement techniques which allowed quantitation down to single drops.

  16. The ATLAS barrel level-1 Muon Trigger Sector-Logic/RX off-detector trigger and acquisition board

    CERN Document Server

    Chiodi, G; Petrolo, E; Pastore, F; Salamon, A; Vari, R; Veneziano, S

    2007-01-01

    The ATLAS experiment uses a system of three concentric layers of Resistive Plate Chambers (RPC) detector for the Level-1 Muon Trigger in the air-core barrel toroid region. The trigger algorithm looks for hit coincidences within different detector layers inside the programmable geometrical road which defines the transverse momentum cut. The on-detector electronics that provides the trigger and detector readout functionalities collects input signals coming from the RPC front-end. Trigger and readout data are then sent via optical fibres to the off-detector electronics. Six or seven optical fibres from one of the 64 trigger sectors go to one Sector-Logic/RX module, that later elaborates the collected trigger and readout data, and sends data respectively to the Read-Out Driver modules and to the Central Level-1 Trigger. We present the functionality and the implementation of the VME Sector-Logic/RX module, and the configuration of the system for the first cosmic ray data collected using this module.

  17. Buddy Board

    DEFF Research Database (Denmark)

    Enggaard, Helle; Moselund, Lene

    2015-01-01

    Projekt ’BuddyBoard’ er kommet i stand via et samarbejde mellem Frederikshavn kommune, Bunker43 og Lab. X. Afdeling en ’Havly’ på Sæby Ældrecenter fungerer som living lab, hvilket betyder, at det udgør et levende laboratorium for udvikling og afprøvning af teknologi (Schultz, 2013). Projektet er....... Bunker43 har udviklet en teknologi (BuddyBoard) til hurtig formidling af billeder fra pårørende og personale til beboere på institutioner. Pårørende og personale uploader billeder via en APP eller en hjemmeside og har mulighed for at tilføje en kort forklarende tekst til hvert billede. Beboeren ser...... billederne via en tablet. Systemet bygger på et simpelt og brugervenligt design, så ældre med kognitive og/eller fysiske funktionsnedsættelser kan anvende teknologien. BuddyBoard fungerer via internettet, og billederne gemmes på en sikret server hos udbyderen, som er Bunker43. Intentionerne med BuddyBoard er...

  18. Development a low-cost carbon monoxide sensor using homemade CW-DFB QCL and board-level electronics

    Science.gov (United States)

    Dang, Jingmin; Yu, Haiye; Zheng, Chuantao; Wang, Lijun; Sui, Yuanyuan; Wang, Yiding

    2018-05-01

    A mid-infrared sensor was demonstrated for the detection of carbon monoxide (CO) at trace level. In order to reduce cost, a homemade continuous-wave mode distributed feedback quantum cascade laser (CW-DFB QCL), a mini gas cell with 1.6-m optical length, and some self-development electronic modules were adopted as excitation source, absorption pool, and signal controlling and processing tool, respectively. Wavelength modulation spectroscopy (WMS) and phase sensitive detection (PSD) techniques as well as wavelet filtering software algorithm were used to reduce the influence of light source fluctuation and system noise and to improve measurement precision and sensitivity. Under the selected P(11) absorption line located at 2099.083 cm-1, a limit of detection (LoD) of 26 parts per billion by volume (ppbv) at atmospheric pressure was achieved with a 1-s acquisition time. Allan deviation was used to characterize the long-term performance of the CO sensor, and a measurement precision of ∼3.4 ppbv was observed with an optimal integration time of ∼114 s. As a field measurement, a continuous monitoring on indoor CO concentration for a period of 24 h was conducted, which verified the reliable and robust operation of the developed sensor.

  19. WeaselBoard :

    Energy Technology Data Exchange (ETDEWEB)

    Mulder, John C.; Schwartz, Moses Daniel; Berg, Michael J.; Van Houten, Jonathan Roger; Urrea, Jorge Mario; King, Michael Aaron; Clements, Abraham Anthony; Jacob, Joshua A.

    2013-10-01

    Critical infrastructures, such as electrical power plants and oil refineries, rely on programmable logic controllers (PLCs) to control essential processes. State of the art security cannot detect attacks on PLCs at the hardware or firmware level. This renders critical infrastructure control systems vulnerable to costly and dangerous attacks. WeaselBoard is a PLC backplane analysis system that connects directly to the PLC backplane to capture backplane communications between modules. WeaselBoard forwards inter-module traffic to an external analysis system that detects changes to process control settings, sensor values, module configuration information, firmware updates, and process control program (logic) updates. WeaselBoard provides zero-day exploit detection for PLCs by detecting changes in the PLC and the process. This approach to PLC monitoring is protected under U.S. Patent Application 13/947,887.

  20. 78 FR 55244 - Senior Executive Service Performance Review Board; Membership

    Science.gov (United States)

    2013-09-10

    ... DEFENSE NUCLEAR FACILITIES SAFETY BOARD Senior Executive Service Performance Review Board... the membership of the Defense Nuclear Facilities Safety Board (DNFSB) Senior Executive Service (SES... rating of a senior executive's performance, the executive's response, and the higher level official's...

  1. 76 FR 57980 - Senior Executive Service Performance Review Board

    Science.gov (United States)

    2011-09-19

    ... DEFENSE NUCLEAR FACILITIES SAFETY BOARD Senior Executive Service Performance Review Board AGENCY... the Defense Nuclear Facilities Safety Board (DNFSB) Senior Executive Service (SES) Performance Review... summary rating of the senior executive's performance, the executive's response, and the higher level...

  2. Gas Pressure-Drop Experiment

    Science.gov (United States)

    Luyben, William L.; Tuzla, Kemal

    2010-01-01

    Most chemical engineering undergraduate laboratories have fluid mechanics experiments in which pressure drops through pipes are measured over a range of Reynolds numbers. The standard fluid is liquid water, which is essentially incompressible. Since density is constant, pressure drop does not depend on the pressure in the pipe. In addition, flow…

  3. Hanging drop crystal growth apparatus

    Science.gov (United States)

    Naumann, Robert J. (Inventor); Witherow, William K. (Inventor); Carter, Daniel C. (Inventor); Bugg, Charles E. (Inventor); Suddath, Fred L. (Inventor)

    1990-01-01

    This invention relates generally to control systems for controlling crystal growth, and more particularly to such a system which uses a beam of light refracted by the fluid in which crystals are growing to detect concentration of solutes in the liquid. In a hanging drop apparatus, a laser beam is directed onto drop which refracts the laser light into primary and secondary bows, respectively, which in turn fall upon linear diode detector arrays. As concentration of solutes in drop increases due to solvent removal, these bows move farther apart on the arrays, with the relative separation being detected by arrays and used by a computer to adjust solvent vapor transport from the drop. A forward scattering detector is used to detect crystal nucleation in drop, and a humidity detector is used, in one embodiment, to detect relative humidity in the enclosure wherein drop is suspended. The novelty of this invention lies in utilizing angular variance of light refracted from drop to infer, by a computer algorithm, concentration of solutes therein. Additional novelty is believed to lie in using a forward scattering detector to detect nucleating crystallites in drop.

  4. Magnetic control of Leidenfrost drops.

    Science.gov (United States)

    Piroird, Keyvan; Clanet, Christophe; Quéré, David

    2012-05-01

    We show how a magnetic field can influence the motion of a paramagnetic drop made of liquid oxygen in a Leidenfrost state on solids at room temperature. It is demonstrated that the trajectory can be modified in both direction and velocity and that the results can be interpreted in terms of classical mechanics as long as the drop does not get too close to the magnet. We study the deviation and report that it can easily overcome 180∘ and even diverge under certain conditions, leading to situations where a drop gets captured. In the vicinity of the magnet, another type of trapping is observed, due to the deformation of the drop in this region, which leads to a strong energy dissipation. Conversely, drops can be accelerated by moving magnets (slingshot effect).

  5. Pool impacts of Leidenfrost drop

    Science.gov (United States)

    Darbois Texier, Baptiste; Maquet, Laurent; Dorbolo, Stephane; Dehandschoewercker, Eline; Pan, Zhao; Truscott, Tadd

    2015-11-01

    This work concerns the impact of a droplet made of a volatile liquid (typically HFE) on a pool of an other liquid (typically silicone oil) which temperature is above the boiling point of the drop. Depending on the properties of the two liquids and the impacting conditions, four different regimes are observed. For low impacting speeds, the droplet bounces on the surface of the bath and finally levitates above it in a Leidenfrost state. Such a regime occurs as soon as the pool temperature exceeds the boiling point of the drop. This observation means that there is no threshold in temperature for a Leidenfrost effect on a liquid surface contrary to the case of a solid substrate. For intermediate impacting velocities, the pinch-off of the surface of the pool entraps the drop in the liquid bulk. The entrapped drop is separated from the pool by a layer of its own vapour in a similar way of antibulles. For increasing impacting speeds, the vapour layer between the drop and the pool does not hold during the pinch-off event. The contact of the drop with the hot liquid provokes a sudden and intense evaporation. At very large impacting speeds, the drop rapidely contacts the pool, spreads and finally induces a hemi-spherical cavity. In the end, these four different regimes are summarized in a Froud-Weber diagram which boundaries are discussed.

  6. Trapping leidenfrost drops with crenelations.

    Science.gov (United States)

    Dupeux, Guillaume; Le Merrer, Marie; Clanet, Christophe; Quéré, David

    2011-09-09

    Drops placed on very hot solids levitate on a cushion of their own vapor, as discovered by Leidenfrost. This confers to these drops a remarkable mobility, which makes problematic their control and manipulation. Here we show how crenelated surfaces can be used to increase the friction of Leidenfrost drops by a factor on the order of 100, making them decelerate and be trapped on centimetric distances instead of the usual metric ones. We measure and characterize the friction force as a function of the design of the crenelations.

  7. Fluvial Systems Tied Together Through a Common Base Level: The Geomorphic Response of the Dirty Devil River, North Wash Creek, and the Colorado River to the Rapid Base Level Drop of Lake Powell

    OpenAIRE

    Majeski, Adam L.

    2009-01-01

    Fluvial adjustment to base level change has its roots in the fundamental concepts of geomorphology. This thesis explores the rate of erosion and sedimentation on the Colorado and Dirty Devil rivers and North Wash Creek under the current base level changes related to the drawdown conditions of Lake Powell. Through cross section and long profile resurveys, the current state of each system is captured and added to the historic record of sedimentation in Lake Powell. All three systems are gene...

  8. Confined thermocapillary motion of a three-dimensional deformable drop

    Science.gov (United States)

    Brady, P. T.; Herrmann, M.; Lopez, J. M.

    2011-02-01

    In this paper, simulations are performed of the thermocapillary motion of three-dimensional and axisymmetric drops in a confined apparatus. The refined level-set grid method is used to track the interface and resolve very small deformations. We compare our results to theoretically predicted thermocapillary migration velocities of drops and to experimentally measured migration velocities in microgravity experiments. The motivation of the present work is to address four important questions surrounding thermocapillary migration. These are as follows. (1) What is the impact of initial conditions on both the initial transient and steady state drop behavior? (2) What is the impact of the domain geometry on drop behavior? (3) Do drops deform for intermediate Marangoni numbers and are those deformations axisymmetric? (4) Can the assumption of constant temperature fluid properties be used when simulating physical experiments? To answer the first question, we explore the parameter space of initial drop temperature distribution and drop holding time. We find that in lower Marangoni number regimes, the drop rapidly settles to a quasisteady state. For larger Marangoni numbers, the initial conditions dominate the drop behavior. To address the second and third questions, we look at the spatial distribution of tangential temperature gradients on the surface of the drop as well as drop deformations and migration velocities. The domain geometry induces nonaxisymmetric deformations and temperature distributions. The results of several axisymmetric runs with realistic physical properties are examined to answer the fourth question. It is found that the variation of material properties influences the drop migration behavior in a nontrivial way.

  9. Soft drop jet mass measurement

    CERN Document Server

    Roloff, Jennifer Kathryn; The ATLAS collaboration

    2018-01-01

    Calculations of jet substructure observables that are accurate beyond leading-logarithm accuracy have recently become available. Such observables are significant not only for probing the collinear regime of QCD that is largely unexplored at a hadron collider, but also for improving the understanding of jet substructure properties that are used in many studies at the Large Hadron Collider. This poster documents a measurement of the first jet substructure quantity at a hadron collider to be calculated at next-to-next-to-leading-logarithm accuracy. The normalized, differential cross-section is measured as a function of log( ρ^2), where ρ is the ratio of the soft-drop mass to the ungroomed jet transverse momentum. This quantity is measured in dijet events from 32.9 ifb of sqrt(s) = 13 TeV proton-proton collisions recorded by the ATLAS detector. The data are unfolded to correct for detector effects and compared to precise QCD calculations and leading-logarithm particle-level Monte Carlo simulations.

  10. 45-FOOT HIGH DROP TOWER

    Data.gov (United States)

    Federal Laboratory Consortium — The Drop Tower is used to simulate and measure the impact shocks that are exerted on parachute loads when they hit the ground. It is also used for HSL static lift to...

  11. Shaping drops with textured surfaces

    Science.gov (United States)

    Ehlinger, Quentin; Biance, Anne-Laure; Ybert, Christophe

    2017-11-01

    When a drop impacts a substrate, it can behave differently depending on the nature of the surface and of the liquid (spreading, bouncing, resting, splashing ...). Understanding these behaviors is crucial to predict the drop morphology during and after impact. Whereas surface wettability has extensively been studied, the effect of surface roughness remains hardly explored. In this work, we consider the impact of a drop in a pure non-wetting situation by using superheated substrates i.e. in the Leidenfrost regime. The surface texture consists of a well-controlled microscopic defect shaped with photolithography on a smooth silicon wafer. Different regimes are observed, depending on the distance between the defect and the impact point and the defect size. Comparing the lamella thickness versus the defect height proves relevant as the transition criteria between regimes. Others characteristics of the drop behavior (direction of satellite droplet ejection, lamella rupture) are also well captured by inertial/capillary models. Drop impacts on multiple defects are also investigated and drop shape well predicted considering the interactions between the local flow and the defects.

  12. Faster multiple emulsification with drop splitting.

    Science.gov (United States)

    Abate, Adam R; Weitz, David A

    2011-06-07

    Microfluidic devices can form emulsions in which the drops have an intricate, controlled structure; however, a challenge is that the droplets are produced slowly, typically only a few millilitres per hour. Here, we present a simple technique to increase the production rate. Using a large drop maker, we produce large drops at a fast volumetric rate; by splitting these drops several times in a splitting array, we create drops of the desired small size. The advantage of this over forming the small drops directly using a small drop maker is that the drops can be formed at much faster rates. This can be applied to the production of single and multiple emulsions.

  13. Evidence of the latest Ordovician sea level drop on Avalonia in the Condroz Inlier, Belgium, and dating with chitinozoans by comparison with the Ashgill type area, Cautley District, U.K.

    Science.gov (United States)

    Vanmeirhaeghe, J.; Vandenbroucke, T.; Verniers, J.

    2003-04-01

    Recently, two conglomerate levels were discovered in the latest Ordovician Génicot Formation in the Puagne area, western Condroz Inlier, Belgium (Herbosch et al. 2001; in press). In the middle of the latter formation, a lower matrix-supported conglomerate approximately 1.2 m thick and with an erosional base is separated by 5.5 m of mudstone and siltstone from a second pebble-supported conglomerate of 2.05 m thick. A local chitinozoan biozonation places both conglomerates in the late Ashgill (stage 6). The sediments of the unit are supposed to be deposited on a moderately deep shelf. However, the sudden presence of the two conglomerates, the lower one with an erosional base, is interpreted as the sedimentological response to the sea level drop associated with the Hirnantian glaciation and deglaciation event (Vanmeirhaeghe &Verniers, submitted). This poster presents the results of a comparison of the chitinozoan biozonation of the Puagne area with that of the Ashgill type area in the Howgill Fells inliers, northern England, U.K. This resulted in a more accurate dating of the two conglomerates and of the complete Génicot and the underlying Fosses Formations in Belgium. A summary of all evidence of the Hirnantian glaciation on the Avalonia microcontinent is shown. HERBOSCH, A., VERNIERS, J., DEBACKER, T., BILLIAERT, B., DE SCHEPPER, S., BELMANS, M. (2001). The Lower Palaeozoic stratigraphy and sedimentology of the Brabant Massif in the Dyle and Orneau valleys and of the Condroz Inlier at Fosses: an excursion guidebook. Pre-symposium excursion of the International Symposium on "Early Palaeozoic Palaeogeographies and Biogeographies of Western Europe and North Africa", Lille USTL, September 22-26, 2001, 1-77. HERBOSCH, A., VERNIERS, J., DEBACKER, T., BILLIAERT, B., DE SCHEPPER, S., BELMANS, M. (2002). The Lower Palaeozoic stratigraphy and sedimentology of the Brabant Massif in the Dyle and Orneau valleys and of the Condroz Inlier at Fosses: an excursion guidebook

  14. Thermocapillary reorientation of Janus drops

    Science.gov (United States)

    Rosales, Rodolfo; Saenz, Pedro

    2017-11-01

    Janus drops, named after the Ancient Roman two-faced god, are liquid drops formed from two immiscible fluids. Experimental observations indicate that a Janus drop may re-orientate in response to an applied external thermal gradient due to the Marangoni effect. Depending on the angle between the interior interface and the direction of the temperature gradient, disparities in the physical properties of the constituent liquids may lead to asymmetries in the thermocapillary flow. As a result, the drop will move along a curved path until a torque-free configuration is achieved, point after which it will continue on a straight trajectory. Here, we present the results of a theoretical investigation of this realignment phenomenon in the Stokes regime and in the limit of non-deformable interfaces. A 3D semi-analytical method in terms of polar spherical harmonics is developed to characterize and rationalize the hydrodynamic response (forces and torques), flow (velocity and temperature distribution) and trajectory of a Janus drop moving during the temperature-driven reorientation process. Furthermore, we discuss how this phenomenon may be exploited to develop dynamically reconfigurable micro-lenses. This work was partially supported by the US National Science Foundation through Grants DMS-1614043 and DMS-1719637.

  15. Interfacial Instabilities in Evaporating Drops

    Science.gov (United States)

    Moffat, Ross; Sefiane, Khellil; Matar, Omar

    2007-11-01

    We study the effect of substrate thermal properties on the evaporation of sessile drops of various liquids. An infra-red imaging technique was used to record the interfacial temperature. This technique illustrates the non-uniformity in interfacial temperature distribution that characterises the evaporation process. Our results also demonstrate that the evaporation of methanol droplets is accompanied by the formation of wave-trains in the interfacial temperature field; similar patterns, however, were not observed in the case of water droplets. More complex patterns are observed for FC-72 refrigerant drops. The effect of substrate thermal conductivity on the structure of the complex pattern formation is also elucidated.

  16. Pressure drop in contraction flow

    DEFF Research Database (Denmark)

    Rasmussen, Henrik Koblitz

    This note is a supplement to Dynamic of Polymeric Liquids (DPL) page 178. DPL gives an equation for the pressure drop in a tapered (and circular) contraction, valid only at low angles. Here the general definition of contraction flow (the Bagley correction) and a more general method to find...

  17. Fluid flow in drying drops

    NARCIS (Netherlands)

    Gelderblom, Hanneke

    2013-01-01

    When a suspension drop evaporates, it leaves behind a drying stain. Examples of these drying stains encountered in daily life are coffee or tea stains on a table top, mineral rings on glassware that comes out of the dishwasher, or the salt deposits on the streets in winter. Drying stains are also

  18. Drops, contact lines, and electrowetting

    NARCIS (Netherlands)

    't Mannetje, Dieter

    2013-01-01

    In this work, we study the behaviour of drops and contact lines under the influence of electric fields, and how these can answer fundamental and industrial questions. Our focus is on studying the varying balance of the electric field, hysteresis forces and inertia as the speed of a contact line

  19. High-Speed Interferometry Under Impacting Drops

    KAUST Repository

    Langley, Kenneth R.

    2017-08-31

    Over the last decade the rapid advances in high-speed video technology, have opened up to study many multi-phase fluid phenomena, which tend to occur most rapidly on the smallest length-scales. One of these is the entrapment of a small bubble under a drop impacting onto a solid surface. Here we have gone from simply observing the presence of the bubble to detailed imaging of the formation of a lubricating air-disc under the drop center and its subsequent contraction into the bubble. Imaging the full shape-evolution of the air-disc has required μm and sub-μs space and time resolutions. Time-resolved 200 ns interferometry with monochromatic light, has allowed us to follow individual fringes to obtain absolute air-layer thicknesses, based on the eventual contact with the solid. We can follow the evolution of the dimple shape as well as the compression of the gas. The improved imaging has also revealed new levels of detail, like the nature of the first contact which produces a ring of micro-bubbles, highlighting the influence of nanometric surface roughness. Finally, for impacts of ultra-viscous drops we see gliding on ~100 nm thick rarified gas layers, followed by extreme wetting at numerous random spots.

  20. Board-to-board consistency in initial dental licensure examinations.

    Science.gov (United States)

    Chambers, David W

    2011-10-01

    The consistency between student clinical performance in dental school and performance on initial licensure examinations is known to be weak. A review of the literature failed to identify any reports of the consistency between performance on initial licensure examinations and quality of technical work in practice. This research examines the consistency of performance among candidates who took two initial licensure examinations given by different testing agencies but for the same jurisdiction within a few weeks of each other. Twenty-seven candidates from one dental school took both the California Dental Board examination and the Western Regional Examining Board initial licensure examinations in 2005 and 2006. Their performance on the patient-based amalgam and composite restorations and the root planing tests were compared in these two board settings and with various dental school measures of competence. Consistent with previous findings, school-to-board performance was barely above chance levels. Board-to-board association was also insignificant and accounted for 12 percent of the common variance in the best case. Patient-based initial licensure examinations have yet to demonstrate validity in terms of consistency of performance for candidates from one performance to the next.

  1. Effect of pressure-drop rate on the isolation of cananga oil using instantaneous controlled pressure-drop process

    OpenAIRE

    Kristiawan, Magdalena; Sobolik, Vaclav; Al Haddad, Mazen; Allaf, Karim

    2008-01-01

    The isolation of Indonesian cananga oil was carried out by a new process, instantaneous controlled pressure drop (DIC). Dry cananga flowers (Cananga odorata Hook. fil. et Thomson, forma macrophylla) were exposed for a short time to saturated steam and then the pressure was abruptly decreased to a vacuum level (about 5 kPa). This abrupt pressure drop provokes auto-vaporization of the superheated volatile compounds, expansion and breaking of the cell walls and instantaneous cooling. In this ...

  2. Device for making liquid drops

    International Nuclear Information System (INIS)

    Yamada, Masao; Fukuda, Fumito; Nishikawa, Masana; Ishii, Takeshi.

    1976-01-01

    Object: To provide a device for producing liquid drops in the form of liquefied gases indispensable to make deuterium and tritium ice pellets used as a fusion fuel in a tokamak type fusion reactor. Structure: First, pressure P 1 at the upper surface of liquefied gas in a container and outlet pressure P 2 of a nozzle disposed at the lower part of the container are adjusted into the state of P 1 >= P 2 , and it is preset so that even under such conditions, the liquefied gas from the nozzle is not naturally flown out. Next, a vibration plate disposed within the container is rapidly downwardly advanced toward the nozzle through a predetermined distance. As a result, pressure of the liquefied gas within a depression under the vibration plate rises instantaneously or in a pulse fashion to dissatisfy the aforesaid set condition whereby the liquefied gas may be flown out from the nozzle in the form of liquid drops. In accordance with the present device, it is possible to produce a suitable number of drops at a suitable point. (Yoshihara, H.)

  3. Dancing drops over vibrating substrates

    Science.gov (United States)

    Borcia, Rodica; Borcia, Ion Dan; Helbig, Markus; Meier, Martin; Egbers, Christoph; Bestehorn, Michael

    2017-04-01

    We study the motion of a liquid drop on a solid plate simultaneously submitted to horizontal and vertical harmonic vibrations. The investigation is done via a phase field model earlier developed for describing static and dynamic contact angles. The density field is nearly constant in every bulk region (ρ = 1 in the liquid phase, ρ ≈ 0 in the vapor phase) and varies continuously from one phase to the other with a rapid but smooth variation across the interfaces. Complicated explicit boundary conditions along the interface are avoided and captured implicitly by gradient terms of ρ in the hydrodynamic basic equations. The contact angle θ is controlled through the density at the solid substrate ρ S , a free parameter varying between 0 and 1 [R. Borcia, I.D. Borcia, M. Bestehorn, Phys. Rev. E 78, 066307 (2008)]. We emphasize the swaying and the spreading modes, earlier theoretically identified by Benilov and Billingham via a shallow-water model for drops climbing uphill along an inclined plane oscillating vertically [E.S. Benilov, J. Billingham, J. Fluid Mech. 674, 93 (2011)]. The numerical phase field simulations will be completed by experiments. Some ways to prevent the release of the dancing drops along a hydrophobic surface into the gas atmosphere are also discussed in this paper.

  4. Active connectors for microfluidic drops on demand

    Energy Technology Data Exchange (ETDEWEB)

    Galas, Jean-Christophe; Studer, Vincent [Laboratoire de Neurobiologie, ESPCI-CNRS UMR 7637, 10 rue Vauquelin 75231 Paris cedex 05 (France); Bartolo, Denis [PMMH-ESPCI-CNRS UMR 7636-Universite Paris 6-Universite Paris 7, 10 rue Vauquelin 75231 Paris cedex 05 (France)], E-mail: jean-christophe.galas@espci.fr, E-mail: denis.bartolo@espci.fr, E-mail: vincent.studer@espci.fr

    2009-07-15

    We introduce a simple and versatile microfluidic drop-on-demand solution that enables independent and dynamical control of both the drop size and the drop production rate. To do so, we combine a standard microfluidic T-junction and a novel active switching component that connects the microfluidic channel to the macroscopic liquid reservoirs. Firstly, we explain how to make this simple but accurate drop-on-demand device. Secondly, we carefully characterize its dynamic response and its range of operations. Finally, we show how to generate complex two-dimensional drop patterns dynamically in single or multiple synchronized drop-on-demand devices.

  5. Getting boards on board: engaging governing boards in quality and safety.

    Science.gov (United States)

    Conway, James

    2008-04-01

    As hospitals seek to drive rapid quality improvement, boards have an opportunity-and a significant responsibility--to make better quality of care the organization's top priority. "Six things all boards should do to improve quality and reduce harm" are recommended: (1) setting aims--set a specific aim to reduce harm this year; make an explicit, public commitment to measurable quality improvement; (2) getting data and hearing stories--select and review progress toward safer care as the first agenda item at every board meeting, grounded in transparency--and putting a "human face" on harm data; (3) establishing and monitoring system-level measures--identify a small group of organizationwide "roll-up" measures of patient safety that are continually updated and are made transparent to the entire organization and its customers; (4) changing the environment, policies, and culture--commit to establish and maintain an environment that is respectful, fair, and just for all who experience the pain and loss as a result of avoidable harm and adverse outcomes: the patients, their families, and the staff at the sharp end of error; (5) learning, starting with the board--develop the board's capability and learn about how "best-in-the-world" boards work with executive and medical staff leaders to reduce harm; (6) establishing executive accountability--oversee the effective execution of a plan to achieve aims to reduce harm, including executive team accountability for clear quality improvement targets.

  6. The effect of obesity levels on irradiated small bowel volume in belly board with small bowel displacement device for rectal cancer radiotherapy

    International Nuclear Information System (INIS)

    Kim, Se Young; Kim, Joo Ho; Park, Hyo Kuk; Cho, Jeong Hee

    2013-01-01

    For radiotherapy in rectal cancer patients treated with small bowel displacement device (SBDD) and belly board, We will suggest new indication of using SBDD depending on obesity index by analyzing correlation between obesity and irradiated small bowel volume. In this study, We reviewed 29 rectal cancer patients who received pelvic radiation therapy with belly board and SBDD from January to April in 2012. We only analyzed those patients treated with three-field technique (PA and both LAT) on 45 Gy (1.8 Gy/fx). We measured patients' height, weight, body mass index (BMI), waist-hip ratio (WHR) and divided BMI into two groups.(≥23:BMI=group 1, <23:BMI=group 2) We performed a statistical analysis to evaluate correlation between total volume of bladder (TV bldder ), obesity index and high dose volume of small bowel (small bowel volume irradiated at 90% of prescribed dose, HDV sb ), low dose volume of small bowel (small bowel volume irradiated at 33% of prescribed dose, LDV sb ). The result shows, gender, WHR and status of pre operative or post operative do not greatly affect HDV sb and LDV sb . Statistical result shows, there are significant correlation between HDV sb and BMI (p<0.04), HDV sb and TV bladder (p<0.01), LDV sb and TV bladder (p<0.01). BMI seems to correlate with HDV sb but does not with LDV sb (p>0.05). There are negative correlation between HDV sb and BMI, TV bladder and HDV sb , TV bladder and LDV sb . Especially, BMI group1 has more effective and negative correlation with HDV sb (p=0.027) than in BMI group 2. In the case of BMI group 1, TV bladder has significant negative correlation with HDV sb and LDV sb (p<0.04). In conclusions, we confirmed that Using SBDD with belly board in BMI group 1 could more effectively reduce irradiated small bowel volume in radiation therapy for rectal cancer. Therefore, We suggest using belly board with SBDD in order to reduce the small bowel toxicity in rectal radiotherapy, if patients' BMI is above 23

  7. The effect of obesity levels on irradiated small bowel volume in belly board with small bowel displacement device for rectal cancer radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Se Young; Kim, Joo Ho; Park, Hyo Kuk; Cho, Jeong Hee [Dept. of Radiation Oncology, Yonsei Cancer Center, Yonsei University Health System, Seoul (Korea, Republic of)

    2013-03-15

    For radiotherapy in rectal cancer patients treated with small bowel displacement device (SBDD) and belly board, We will suggest new indication of using SBDD depending on obesity index by analyzing correlation between obesity and irradiated small bowel volume. In this study, We reviewed 29 rectal cancer patients who received pelvic radiation therapy with belly board and SBDD from January to April in 2012. We only analyzed those patients treated with three-field technique (PA and both LAT) on 45 Gy (1.8 Gy/fx). We measured patients' height, weight, body mass index (BMI), waist-hip ratio (WHR) and divided BMI into two groups.(≥23:BMI=group 1, <23:BMI=group 2) We performed a statistical analysis to evaluate correlation between total volume of bladder (TV{sub bldder}), obesity index and high dose volume of small bowel (small bowel volume irradiated at 90% of prescribed dose, HDV{sub sb}), low dose volume of small bowel (small bowel volume irradiated at 33% of prescribed dose, LDV{sub sb}). The result shows, gender, WHR and status of pre operative or post operative do not greatly affect HDV{sub sb} and LDV{sub sb}. Statistical result shows, there are significant correlation between HDV{sub sb} and BMI (p<0.04), HDV{sub sb} and TV{sub bladder} (p<0.01), LDV{sub sb} and TV{sub bladder} (p<0.01). BMI seems to correlate with HDV{sub sb} but does not with LDV{sub sb} (p>0.05). There are negative correlation between HDV{sub sb} and BMI, TV{sub bladder} and HDV{sub sb}, TV{sub bladder} and LDV{sub sb} . Especially, BMI group1 has more effective and negative correlation with HDV{sub sb} (p=0.027) than in BMI group 2. In the case of BMI group 1, TV{sub bladder} has significant negative correlation with HDV{sub sb} and LDV{sub sb} (p<0.04). In conclusions, we confirmed that Using SBDD with belly board in BMI group 1 could more effectively reduce irradiated small bowel volume in radiation therapy for rectal cancer. Therefore, We suggest using belly board with SBDD in order

  8. The Investigation of Chemistry Questions Asked in Free Boarding and Scholarship Examination for High School Level in the Context of Algorithmic and Conceptual Question Type

    Directory of Open Access Journals (Sweden)

    Ayşegül DERMAN

    2016-06-01

    Full Text Available To conduct of the education programs, the most important resource is considered that textbooks but in national assesment tests, chemistry questions prepared according to chemistry curriculum they may be considered reflections of curriculum. The purpose of this study is to review the 140 chemistry questions “algoritmic or conceptual”, asked in “Free Boarding and Scholarship Examination”for 9,10,11 classes between 1998 and 2015 years. The study is a descriptive study. In data analysis, within the scope of the document analysis, qualitative research method was used. Crosstabs and Kappa statistic was used. The findings of this study revealed that the questions asked in “Free Boarding and Scholarship Examination”are 80% conceptual, 20% algorithmic in total. The distribution of question types according to the years indicates that most of questions are consisted of conceptual question types. By the findings are associated with the relevant literature and national chemistry curriculum, inferences and implications for conceptual chemistry teaching and learning have been made

  9. Packaging Reliability Effect of ENIG and ENEPIG Surface Finishes in Board Level Thermal Test under Long-Term Aging and Cycling.

    Science.gov (United States)

    Shen, Chaobo; Hai, Zhou; Zhao, Cong; Zhang, Jiawei; Evans, John L; Bozack, Michael J; Suhling, Jeffrey C

    2017-04-26

    This study illustrates test results and comparative literature data on the influence of isothermal aging and thermal cycling associated with Sn-1.0Ag-0.5Cu (SAC105) and Sn-3.0Ag-0.5Cu (SAC305) ball grid array (BGA) solder joints finished with ENIG and ENEPIG on the board side and ENIG on the package side compared with ImAg plating on both sides. The resulting degradation data suggests that the main concern for 0.4 mm pitch 10 mm package size BGA is package side surface finish, not board side. That is, ENIG performs better than immersion Ag for applications involving long-term isothermal aging. SAC305, with a higher relative fraction of Ag₃Sn IMC within the solder, performs better than SAC105. SEM and polarized light microscope analysis show cracks propagated from the corners to the center or even to solder bulk, which eventually causes fatigue failure. Three factors are discussed: IMC, grain structure, and Ag₃Sn particle. The continuous growth of Cu-Sn intermetallic compounds (IMC) and grains increase the risk of failure, while Ag₃Sn particles seem helpful in blocking the crack propagation.

  10. Departmental Appeals Board Decisions

    Data.gov (United States)

    U.S. Department of Health & Human Services — Decisions issued by the Chair and Board Members of the Departmental Appeals Board concerning determinations in discretionary, project grant programs, including...

  11. Pilot Boarding Areas

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Pilot boarding areas are locations at sea where pilots familiar with local waters board incoming vessels to navigate their passage to a destination port. Pilotage is...

  12. Drag and drop display & builder

    Energy Technology Data Exchange (ETDEWEB)

    Bolshakov, Timofei B.; Petrov, Andrey D.; /Fermilab

    2007-12-01

    The Drag and Drop (DnD) Display & Builder is a component-oriented system that allows users to create visual representations of data received from data acquisition systems. It is an upgrade of a Synoptic Display mechanism used at Fermilab since 2002. Components can be graphically arranged and logically interconnected in the web-startable Project Builder. Projects can be either lightweight AJAX- and SVG-based web pages, or they can be started as Java applications. The new version was initiated as a response to discussions between the LHC Controls Group and Fermilab.

  13. Scrum Board Game

    Science.gov (United States)

    van den Oord, Stefan; van de Goor, Wim

    The Scrum Board Game is a workshop for beginners. It is for people with any role (customer, developer, tester, etc.), who don’t exactly know what a Scrum Board is, or how to create one themselves. The workshop teaches the benefits of a Scrum Board, how to use it, and how to introduce it in projects.

  14. Liz Fradd gets to the heart of the pressing need for better nursing leadership at the strategic level (reflections October 14). Nurse directors need to have specific training to help them be more effective at board level.

    Science.gov (United States)

    Gleeson, Catherine

    2009-11-18

    Senior nurses should be at the board table where their clinical authority can be used to inform and influence a more holistic approach to quality monitoring across the care pathway. Meeting government time targets for seeing a GP, consultant or moving out of A&E are only small pieces of the quality jigsaw.

  15. Preserving the Legitimacy of Board Certification.

    Science.gov (United States)

    Hanemann, Michael S; Wall, Holly C; Dean, John A

    2017-06-01

    The aims of this discussion were to inform the medical community about the American Board of Cosmetic Surgery's ongoing attempts in Louisiana to achieve equivalency to American Board of Medical Specialties (ABMS) member boards so that its diplomates may use the term "board certified" in advertising and to ensure public safety by upholding the standards for medical board certification. In 2011, Louisiana passed a truth in medical advertising law, which was intended to protect the public by prohibiting the use of the term "board certified" by improperly credentialed physicians. An American Board of Cosmetic Surgery diplomate petitioned the Louisiana State Board of Medical Examiners to approve a rule that would establish a pathway to equivalency for non-ABMS member boards, whose diplomates have not completed training approved by the Accreditation Council for Graduate Medical Education (ACGME) in the specialty they are certifying. Physicians and physician organizations representing multiple specialties (facial plastic and reconstructive surgery, otolaryngology [head and neck surgery], orthopedic spine surgery, pediatric neurosurgery, dermatology, and plastic surgery) urged the Louisiana State Board of Medical Examiners to clarify its advertising policy, limiting the use of the term "board certified" to physicians who have completed ACGME-approved training in the specialty or subspecialty named in the certificate. The public equates the term "board certified" with the highest level of expertise in a medical specialty. When a certifying board does not require completion of ACGME or American Osteopathic Association (AOA)-accredited training in the specialty it certifies, the result is an unacceptable degree of variability in the education and training standards applied to its diplomates. Independent, third-party oversight of certifying boards and training programs is necessary to ensure quality standards are upheld. Any system that assesses a non-ABMS member or non

  16. Board of Directors or Supervisory Board

    DEFF Research Database (Denmark)

    Werlauff, Erik

    2009-01-01

    The article analyses the legal consequences of the choice now available to Danish public limited companies, which can now opt for a two-tier management structure, in which the management board undertakes both the day-to-day and the overall management, while a supervisory board exercises control...... over the management board, including its appointment and dismissal. The article considers which companies a two-tier structure may be relevant for, and reviews the consequences for the composition, election and functioning of the company organs....

  17. Vibration-Induced Climbing of Drops

    Science.gov (United States)

    Brunet, P.; Eggers, J.; Deegan, R. D.

    2007-10-01

    We report an experimental study of liquid drops moving against gravity, when placed on a vertically vibrating inclined plate, which is partially wetted by the drop. The frequency of vibrations ranges from 30 to 200 Hz, and, above a threshold in vibration acceleration, drops experience an upward motion. We attribute this surprising motion to the deformations of the drop, as a consequence of an up or down symmetry breaking induced by the presence of the substrate. We relate the direction of motion to contact angle measurements. This phenomenon can be used to move a drop along an arbitrary path in a plane, without special surface treatments or localized forcing.

  18. The effect of dropping impact on bruising pomegranate fruit

    Directory of Open Access Journals (Sweden)

    M Mohammad Shafie

    2016-04-01

    fruit can still be bruised if its acceleration exceeds a certain value. These relationships provide an effective basis to predict and control drop bruising, which may be achieved through the design of reasonable cushioning packaging for fruit. Conclusions: This research applied the concept of dropping bruise for pomegranate fruits. Because of the limitations in using conventional testing methods to test product of a viscoelastic nature, such as fruit, free fall dropping tests were adapted to determine dropping bruise fragility and bruise boundary for ‘Malas-e-Saveh’ pomegranates at different drop heights. For viscoelastic products such as fruit, even if the dropping impact velocity approached zero, the fruit could be bruised as long as the impact acceleration exceeded a certain value (critical acceleration. A series of bruise boundaries can be established for different levels of bruise ratios, i.e., a contour of constant bruise ratio can be drawn on the velocity acceleration plane.

  19. MATTERS PRESENTED AT THE JOINT BOARDS MEETING

    CERN Multimedia

    T. Virdee

    CMS Organisation (T. Virdee) The Management Board endorsed J. Incandela as Deputy Physics Coordinator; he would move to CERN in the middle of 2007. The Board also took note of the Level-2 Convenors in Computing, Offline Software and Physics. Suggestions for the unfilled positions were still welcome. It was urgent to appoint a Database Coordinator. In the cases where only one Level-2 coordinator was being nominated the second would be nominated in 9 months. It was stressed that the SLHC working group must do real simulations to address questions about the machine design. The Management Board took note of the proposal to formally assign Mentors to Physics and analysis groups, of the nominations of the Convenors of the Detector Performance Groups and recommended that the Trigger Coordinator be appointed soon. Discussion on Technical Recommendations (A. Ball) The Board was reminded of the conclusions presented at the Joint Boards meeting. The present planning assumed that the YB0 services installation could...

  20. Hydrodynamic shrinkage of liquid CO2 Taylor drops in a straight microchannel.

    Science.gov (United States)

    Qin, Ning; Wen, John; Ren, Carolyn L

    2018-01-16

    Hydrodynamic shrinkage of liquid CO2 drops in water under a Taylor flow regime is studied using a straight microchannel (length/width ~ 100). A general form of a mathematical model of the solvent-side mass transfer coefficient (ks) is developed first. Based on formulations of the surface area (A) and the volume (V) of a general Taylor drop in a rectangular microchannel, a specific form of ks is derived. Drop length and speed are experimentally measured at three specified positions of the straight channel, namely, immediately after drop generation (position 1), the midpoint of the channel (position 2) and the end of the channel (position 3). The reductions of drop length (Lx, x = 1, 2, 3) from position 1 to 2 and down to 3 are used to quantify the drop shrinkage. Using the specific model, ks is calculated mainly based on Lx and drop flowing time (t). Results show that smaller CO2 drops produced by lower flow rate ratios (QLCO2/QH2O) are generally characterized by higher (nearly three times) ks and Sherwood numbers than those produced by higher QLCO2/QH2O, which is essentially attributed to the larger effective portion of the smaller drop contributing in the mass transfer under same levels of the flowing time and the surface-to-volume ratio (~ 104 m-1) of all drops. Based on calculated pressure drops of the segmented flow in microchannel, the Peng-Robinson equation of state (EOS) and initial pressures of drops at the T-junction in experiments, overall pressure drop (ΔPt) in the straight channel as well as the resulted drop volume change are quantified. ΔPt from position 1 to 3 is by average 3.175 kPa with a ~1.6% standard error, which only leads to relative drop volume changes of 0.3‰ to 0.52‰. © 2018 IOP Publishing Ltd.

  1. THE EFFECTS OF THE INTERACTIVE WHITE BOARD USAGE ON THE STUDENDTS’ LEARNING LEVEL AND AN APPLICATION IN THE FINANCIAL MARKETS COURSES

    Directory of Open Access Journals (Sweden)

    Yasemin ERTAN

    2011-07-01

    Full Text Available The effect of intense and fast lifestyle emerged from globalization has also an influence on education. As the access to the information increases, the information load on the students is increasing gradually as well. The need to give more and new information to the students in a short period of time made new technologies a requirement to be used in education. For this reason, lecturers are searching for new ways that they can teach more efficiently and get benefit from the educational technologies to make students learn more easily. These tendencies are also observed in the accounting and finance in which the numerical data is intensively used. According to various educational theories, using visual aid as well as audio methods is increasing the efficiency of the education. On the other hand, conventional teaching methods are supported by PowerPoint presentations and the need of internet utilization appears in the finance education due to the importance of accounting and mathematical calculations. The use of interactive whiteboard technique, that is an educational method providing these opportunities, is quite new. This study examines how interactive white board technique, that appeals to students both aurally and visually, affects graduate students’ learning in “Financial Markets Course” by using pretest-posttest control group model.

  2. Interface analysis of embedded chip resistor device package and its effect on drop shock reliability.

    Science.gov (United States)

    Park, Se-Hoon; Kim, Sun Kyoung; Kim, Young-Ho

    2012-04-01

    In this study, the drop reliability of an embedded passive package is investigated under JESD22-B111 condition. Chip resistors were buried in a PCB board, and it was electrically interconnected by electroless and electrolytic copper plating on a tin pad of a chip resistor without intermetallic phase. However tin, nickel, and copper formed a complex intermetallic phase, such as (Cu, Ni)6Sn5, (Cu, Ni)3Sn, and (Ni, Cu)3Sn2, at the via interface and via wall after reflow and aging. Since the amount of the tin layer was small compared with the solder joint, excessive intermetallic layer growth was not observed during thermal aging. Drop failures are always initiated at the IMC interface, and as aging time increases Cu-Sn-Ni IMC phases are transformed continuously due to Cu diffusion. We studied the intermetallic formation of the Cu via interface and simulated the stress distribution of drop shock by using material properties and board structure of embedded passive boards. The drop simulation was conducted according to the JEDEC standard. It was revealed that the crack starting point related to failure fracture changed due to intermetallic phase transformation along the via interface, and the position where failure occurs experimentally agrees well with our simulation results.

  3. Leidenfrost drops on a heated liquid pool

    Science.gov (United States)

    Maquet, L.; Sobac, B.; Darbois-Texier, B.; Duchesne, A.; Brandenbourger, M.; Rednikov, A.; Colinet, P.; Dorbolo, S.

    2016-09-01

    We show that a volatile liquid drop placed at the surface of a nonvolatile liquid pool warmer than the boiling point of the drop can be held in a Leidenfrost state even for vanishingly small superheats. Such an observation points to the importance of the substrate roughness, negligible in the case considered here, in determining the threshold Leidenfrost temperature. A theoretical model based on the one proposed by Sobac et al. [Phys. Rev. E 90, 053011 (2014), 10.1103/PhysRevE.90.053011] is developed in order to rationalize the experimental data. The shapes of the drop and of the liquid substrate are analyzed. The model notably provides scalings for the vapor film thickness profile. For small drops, these scalings appear to be identical to the case of a Leidenfrost drop on a solid substrate. For large drops, in contrast, they are different, and no evidence of chimney formation has been observed either experimentally or theoretically in the range of drop sizes considered in this study. Concerning the evaporation dynamics, the radius is shown to decrease linearly with time whatever the drop size, which differs from the case of a Leidenfrost drop on a solid substrate. For high superheats, the characteristic lifetime of the drops versus the superheat follows a scaling law that is derived from the model, but, at low superheats, it deviates from this scaling by rather saturating.

  4. Star-shaped oscillations of Leidenfrost drops

    Science.gov (United States)

    Ma, Xiaolei; Liétor-Santos, Juan-José; Burton, Justin C.

    2017-03-01

    We experimentally investigate the self-sustained, star-shaped oscillations of Leidenfrost drops. The drops levitate on a cushion of evaporated vapor over a heated, curved surface. We observe modes with n =2 -13 lobes around the drop periphery. We find that the wavelength of the oscillations depends only on the capillary length of the liquid and is independent of the drop radius and substrate temperature. However, the number of observed modes depends sensitively on the liquid viscosity. The dominant frequency of pressure variations in the vapor layer is approximately twice the drop oscillation frequency, consistent with a parametric forcing mechanism. Our results show that the star-shaped oscillations are driven by capillary waves of a characteristic wavelength beneath the drop and that the waves are generated by a large shear stress at the liquid-vapor interface.

  5. Sepsis from dropped clips at laparoscopic cholecystectomy

    Energy Technology Data Exchange (ETDEWEB)

    Hussain, Sarwat E-mail: sarwathussain@hotmail.com

    2001-12-01

    We report seven patients in whom five dropped surgical clips and two gallstones were visualized in the peritoneal cavity, on radiological studies. In two, subphrenic abscesses and empyemas developed as a result of dropped clips into the peritoneal cavity during or following laparoscopic cholecystectomy. In one of these two, a clip was removed surgically from the site of an abscess. In two other patients dropped gallstones, and in three, dropped clips led to no complications. These were seen incidentally on studies done for other indications. Abdominal abscess secondary to dropped gallstones is a well-recognized complication of laparoscopic cholecystectomy (LC). We conclude that even though dropped surgical clips usually do not cause problems, they should be considered as a risk additional to other well-known causes of post-LC abdominal sepsis.

  6. Sepsis from dropped clips at laparoscopic cholecystectomy

    International Nuclear Information System (INIS)

    Hussain, Sarwat

    2001-01-01

    We report seven patients in whom five dropped surgical clips and two gallstones were visualized in the peritoneal cavity, on radiological studies. In two, subphrenic abscesses and empyemas developed as a result of dropped clips into the peritoneal cavity during or following laparoscopic cholecystectomy. In one of these two, a clip was removed surgically from the site of an abscess. In two other patients dropped gallstones, and in three, dropped clips led to no complications. These were seen incidentally on studies done for other indications. Abdominal abscess secondary to dropped gallstones is a well-recognized complication of laparoscopic cholecystectomy (LC). We conclude that even though dropped surgical clips usually do not cause problems, they should be considered as a risk additional to other well-known causes of post-LC abdominal sepsis

  7. HIV Patients Drop Out in Indonesia: Associated Factors and Potential Productivity Loss.

    Science.gov (United States)

    Siregar, Adiatma Ym; Pitriyan, Pipit; Wisaksana, Rudi

    2016-07-01

    this study reported various factors associated with a higher probability of HIV patients drop out, and potential productivity loss due to HIV patients drop out. we analyzed data of 658 HIV patients from a database in a main referral hospital in Bandung city, West Java, Indonesia from 2007 to 2013. First, we utilized probit regression analysis and included, among others, the following variables: patients' status (active or drop out), CD4 cell count, TB and opportunistic infection (OI), work status, sex, history of injecting drugs, and support from family and peers. Second, we used the drop out data from our database and CD 4 cell count decline rate from another study to estimate the productivity loss due to HIV patients drop out. lower CD4 cell count was associated with a higher probability of drop out. Support from family/peers, living with family, and diagnosed with TB were associated with lower probability of drop out. The productivity loss at national level due to treatment drop out (consequently, due to CD4 cell count decline) can reach US$365 million (using average wage). first, as lower CD 4 cell count was associated with higher probability of drop out, we recommend (to optimize) early ARV initiation at a higher CD 4 cell count, involving scaling up HIV service at the community level. Second, family/peer support should be further emphasized to further ensure treatment success. Third, dropping out from ART will result in a relatively large productivity loss.

  8. Hydrothermal waves in evaporating sessile drops

    OpenAIRE

    Brutin, D.; Rigollet, F.; Niliot, C. Le

    2009-01-01

    Drop evaporation is a simple phenomena but still unclear concerning the mechanisms of evaporation. A common agreement of the scientific community based on experimental and numerical work evidences that most of the evaporation occurs at the triple line. However, the rate of evaporation is still empirically predicted due to the lack of knowledge on the convection cells which develop inside the drop under evaporation. The evaporation of sessile drop is more complicated than it appears due to the...

  9. Hydrocarbon Degradation In Poultry Droppings And Cassava Peels ...

    African Journals Online (AJOL)

    This greenhouse study was aimed at determining the potentials of poultry droppings (PD) and cassava peels (CP) for nutrient-enhanced biodegradation of petroleum hydrocarbon (THC) in a well drained Typic Paleustults using the THC levels and degradation duration as remediation indices. The performance of the organic ...

  10. 24 hydrocarbon degradation in poultry droppings and cassava peels

    African Journals Online (AJOL)

    OLUWOLE AKINNAGBE

    2009-01-01

    Jan 1, 2009 ... ABSTRACT. This greenhouse study was aimed at determining the potentials of poultry droppings (PD) and cassava peels. (CP) for nutrient-enhanced biodegradation of petroleum hydrocarbon (THC) in a well drained Typic. Paleustults using the THC levels and degradation duration as remediation indices.

  11. Tutoring Center Effectiveness: The Effect of Drop-In Tutoring

    Science.gov (United States)

    Cooper, Erik

    2010-01-01

    While tutoring as a whole has been demonstrated to improve student learning across a variety of subjects and age groups, there is little published evidence for the effectiveness of drop-in tutoring at the undergraduate level. This type of tutoring can be derided as homework help; however, it is clear from this study that students who made use of…

  12. 7 CFR 1250.304 - Egg Board or Board.

    Science.gov (United States)

    2010-01-01

    ... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE EGG RESEARCH AND PROMOTION Egg Research and Promotion Order Definitions § 1250.304 Egg Board or Board. Egg Board or Board or other designatory term adopted by such Board, with the approval of the Secretary, means the administrative body...

  13. A Novel Virus Causes Scale Drop Disease in Lates calcarifer.

    Directory of Open Access Journals (Sweden)

    Ad de Groof

    2015-08-01

    Full Text Available From 1992 onwards, outbreaks of a previously unknown illness have been reported in Asian seabass (Lates calcarifer kept in maricultures in Southeast Asia. The most striking symptom of this emerging disease is the loss of scales. It was referred to as scale drop syndrome, but the etiology remained enigmatic. By using a next-generation virus discovery technique, VIDISCA-454, sequences of an unknown virus were detected in serum of diseased fish. The near complete genome sequence of the virus was determined, which shows a unique genome organization, and low levels of identity to known members of the Iridoviridae. Based on homology of a series of putatively encoded proteins, the virus is a novel member of the Megalocytivirus genus of the Iridoviridae family. The virus was isolated and propagated in cell culture, where it caused a cytopathogenic effect in infected Asian seabass kidney and brain cells. Electron microscopy revealed icosahedral virions of about 140 nm, characteristic for the Iridoviridae. In vitro cultured virus induced scale drop syndrome in Asian seabass in vivo and the virus could be reisolated from these infected fish. These findings show that the virus is the causative agent for the scale drop syndrome, as each of Koch's postulates is fulfilled. We have named the virus Scale Drop Disease Virus. Vaccines prepared from BEI- and formalin inactivated virus, as well as from E. coli produced major capsid protein provide efficacious protection against scale drop disease.

  14. Building better boards.

    Science.gov (United States)

    Nadler, David A

    2004-05-01

    Companies facing new requirements for governance are scrambling to buttress financial-reporting systems, overhaul board structures--whatever it takes to comply. But there are limits to how much good governance can be imposed from the outside. Boards know what they ought to be: seats of challenge and inquiry that add value without meddling and make CEOs more effective but not all-powerful. A board can reach that goal only if it functions as a high-performance team, one that is competent, coordinated, collegial, and focused on an unambiguous goal. Such entities don't just evolve; they must be constructed to an exacting blueprint--what the author calls board building. In this article, Nadler offers an agenda and a set of tools that boards can use to define and achieve their objectives. It's important for a board to conduct regular self-assessments and to pay attention to the results of those analyses. As a first step, the directors and the CEO should agree on which of the following common board models best fits the company: passive, certifying, engaged, intervening, or operating. The directors and the CEO should then analyze which business tasks are most important and allot sufficient time and resources to them. Next, the board should take inventory of each director's strengths to ensure that the group as a whole possesses the skills necessary to do its work. Directors must exert more influence over meeting agendas and make sure they have the right information at the right time and in the right format to perform their duties. Finally, the board needs to foster an engaged culture characterized by candor and a willingness to challenge. An ambitious board-building process, devised and endorsed both by directors and by management, can potentially turn a good board into a great one.

  15. Are the Stress Drops of Small Earthquakes Good Predictors of the Stress Drops of Larger Earthquakes?

    Science.gov (United States)

    Hardebeck, J.

    2017-12-01

    Uncertainty in PSHA could be reduced through better estimates of stress drop for possible future large earthquakes. Studies of small earthquakes find spatial variability in stress drop; if large earthquakes have similar spatial patterns, their stress drops may be better predicted using the stress drops of small local events. This regionalization implies the variance with respect to the local mean stress drop may be smaller than the variance with respect to the global mean. I test this idea using the Shearer et al. (2006) stress drop catalog for M1.5-3.1 events in southern California. I apply quality control (Hauksson, 2015) and remove near-field aftershocks (Wooddell & Abrahamson, 2014). The standard deviation of the distribution of the log10 stress drop is reduced from 0.45 (factor of 3) to 0.31 (factor of 2) by normalizing each event's stress drop by the local mean. I explore whether a similar variance reduction is possible when using the Shearer catalog to predict stress drops of larger southern California events. For catalogs of moderate-sized events (e.g. Kanamori, 1993; Mayeda & Walter, 1996; Boyd, 2017), normalizing by the Shearer catalog's local mean stress drop does not reduce the standard deviation compared to the unmodified stress drops. I compile stress drops of larger events from the literature, and identify 15 M5.5-7.5 earthquakes with at least three estimates. Because of the wide range of stress drop estimates for each event, and the different techniques and assumptions, it is difficult to assign a single stress drop value to each event. Instead, I compare the distributions of stress drop estimates for pairs of events, and test whether the means of the distributions are statistically significantly different. The events divide into 3 categories: low, medium, and high stress drop, with significant differences in mean stress drop between events in the low and the high stress drop categories. I test whether the spatial patterns of the Shearer catalog

  16. Atomic Energy Control Board

    International Nuclear Information System (INIS)

    Blackman, N.S.; Gummer, W.K.

    1982-02-01

    This paper has been prepared to provide an overview of the responsibilities and activities of the Atomic Energy Control Board. It is designed to address questions that are often asked concerning the establishment of the Atomic Energy Control Board, its enabling legislation, licensing and compliance activities, federal-provincial relationships, international obligations, and communications with the public

  17. Many Drops Make a Lake

    Directory of Open Access Journals (Sweden)

    Chaitanya S. Mudgal

    2014-03-01

    greater knowledge, better skills and disseminate this knowledge through this journal to influence as many physicians and their patients as possible. They have taken the knowledge of their teachers, recognized their giants and are now poised to see further than ever before. My grandmother often used to quote to me a proverb from India, which when translated literally means “Many drops make a lake”. I cannot help but be amazed by the striking similarities between the words of Newton and this Indian saying. Therefore, while it may seem intuitive, I think it must be stated that it is vital for the betterment of all our patients that we recognize our own personal lakes to put our drops of knowledge into. More important is that we recognize that it is incumbent upon each and every one of us to contribute to our collective lakes of knowledge such as ABJS. And finally and perhaps most importantly we need to be utterly cognizant of never letting such lakes of knowledge run dry.... ever.

  18. GENDER, DEBT, AND DROPPING OUT OF COLLEGE.

    Science.gov (United States)

    Dwyer, Rachel E; Hodson, Randy; McLoud, Laura

    2013-02-01

    For many young Americans, access to credit has become critical to completing a college education and embarking on a successful career path. Young people increasingly face the trade-off of taking on debt to complete college or foregoing college and taking their chances in the labor market without a college degree. These trade-offs are gendered by differences in college preparation and support and by the different labor market opportunities women and men face that affect the value of a college degree and future difficulties they may face in repaying college debt. We examine these new realities by studying gender differences in the role of debt in the pivotal event of graduating from college using the 1997 cohort of the national longitudinal Survey of youth. In this article, we find that women and men both experience slowing and even diminishing probabilities of graduating when carrying high levels of debt, but that men drop out at lower levels of debt than do women. We conclude by theorizing that high levels of debt are one of the mechanisms that sort women and men into different positions in the social stratification system.

  19. Drop test facility available to private industry

    International Nuclear Information System (INIS)

    Shappert, L.B.; Box, W.D.

    1983-01-01

    In 1978, a virtually unyielding drop test impact pad was constructed at Oak Ridge National Laboratory's (ORNL's) Tower Shielding Facility (TSF) for the testing of heavy shipping containers designed for transporting radioactive materials. Because of the facility's unique capability for drop-testing large, massive shipping packages, it has been identified as a facility which can be made available for non-DOE users

  20. Total Site Heat Integration Considering Pressure Drops

    Directory of Open Access Journals (Sweden)

    Kew Hong Chew

    2015-02-01

    Full Text Available Pressure drop is an important consideration in Total Site Heat Integration (TSHI. This is due to the typically large distances between the different plants and the flow across plant elevations and equipment, including heat exchangers. Failure to consider pressure drop during utility targeting and heat exchanger network (HEN synthesis may, at best, lead to optimistic energy targets, and at worst, an inoperable system if the pumps or compressors cannot overcome the actual pressure drop. Most studies have addressed the pressure drop factor in terms of pumping cost, forbidden matches or allowable pressure drop constraints in the optimisation of HEN. This study looks at the implication of pressure drop in the context of a Total Site. The graphical Pinch-based TSHI methodology is extended to consider the pressure drop factor during the minimum energy requirement (MER targeting stage. The improved methodology provides a more realistic estimation of the MER targets and valuable insights for the implementation of the TSHI design. In the case study, when pressure drop in the steam distribution networks is considered, the heating and cooling duties increase by 14.5% and 4.5%.

  1. Drop dispensing in a viscous outer liquid

    Directory of Open Access Journals (Sweden)

    Claudiu PATRASCU

    2017-12-01

    Full Text Available The formation and detachment of Newtonian drops in viscous external liquids is investigated. A global analysis of two necking processes is presented in order to highlight the behavior of such thinning phenomena, when controlled either by inertia or by viscous effects. Moving detached droplets in an immiscible outer liquid were studied in terms of velocity and drop-travel distance. Theoretical predictions are proposed and compared with experimental data for the volume of the drop and for the subsequent dynamics that follow after detachment. Our investigations point out that the drop rapidly achieves constant velocity, the value of it being in a satisfactory agreement with the model. Both the influence of the flow rate and that of the material properties on drop volume are pursued.

  2. Breakfast patterns of frozen impacted drops

    Science.gov (United States)

    Thievenaz, Virgile; Josserand, Christophe; Seon, Thomas

    2017-11-01

    We investigate experimentally the solidification of a water drop during its impact on a sub-zero cooled metallic plate. As the drop impacts the substrate, a first thin layer of ice builds-up in the briefest moment. Afterwards, the competition between the liquid solidification and its retraction on this ice layer leads to a variety of frozen drop patterns. Typically, with a change of temperature the drop can freeze into a fried egg or a doughnut shape. These frozen motifs experience different sizes and can even disappear so only the thin pancake remains. These patterns have been explored through a range of parameters such as : plate temperature, thermal properties, drop size and impact velocity. Phase-diagrams show the range and the transition temperatures between the different patterns as a function of those parameters. The experimental results are discussed using a scaling law approach, allowing basic understanding of the underlying physics.

  3. Wetting and evaporation of binary mixture drops.

    Science.gov (United States)

    Sefiane, Khellil; David, Samuel; Shanahan, Martin E R

    2008-09-11

    Experimental results on the wetting behavior of water, methanol, and binary mixture sessile drops on a smooth, polymer-coated substrate are reported. The wetting behavior of evaporating water/methanol drops was also studied in a water-saturated environment. Drop parameters (contact angle, shape, and volume) were monitored in time. The effects of the initial relative concentrations on subsequent evaporation and wetting dynamics were investigated. Physical mechanisms responsible for the various types of wetting behavior during different stages are proposed and discussed. Competition between evaporation and hydrodynamic flow are evoked. Using an environment saturated with water vapor allowed further exploration of the controlling mechanisms and underlying processes. Wetting stages attributed to differential evaporation of methanol were identified. Methanol, the more volatile component, evaporates predominantly in the initial stage. The data, however, suggest that a small proportion of methanol remained in the drop after the first stage of evaporation. This residual methanol within the drop seems to influence subsequent wetting behavior strongly.

  4. Establishing Proficiency Levels for the Delaware Student Testing Program in Science and Social Studies, Grades 4 & 6. Report and Recommendations to the Delaware State Board of Education.

    Science.gov (United States)

    Delaware State Dept. of Education, Dover. Assessment and Accountability Branch.

    This document contains the results of a standard setting conducted in January 2002 on the Delaware Student Testing Program (DSTP) Science and Social Studies tests at grades 4 and 6. Each standard setting process entailed convening four groups, one for each grade level and content area, and each group met for 2 days. At the standard setting judges…

  5. Update on the Purdue University 2-second Drop Tower

    Science.gov (United States)

    Collicott, Steven

    A small drop tower of approximately one second drop duration was built in the School of Aero-nautics and Astronautics at Purdue University beginning in 1998 and operated until summer 2007. This inexpensive tower in an old airplane hanger, was built largely by Yongkang Chen, now a Research Professor at Portland State University in Oregon, USA. In about 7 years of operations, the tower generated sufficient science results for Chen's PhD thesis[1] (summarized in three AIAA Journal papers[2-4]), Fitzpatrick's MS thesis[5], two industry projects for since-canceled advanced rodent habitats for ISS, and one project for NASA Marshall. In addition to the science use, Purdue undergraduate students designed, built, and performed simpler fluids experiments for their own career advancement, including a novel investigation of the impact of imperfect repeatability of initial conditions on a zero-g fluids experiment. The tower was also used for outreach to school children. It is most satisfying that Chen's PhD research in this small tower, and subsequent discussions and interactions, helped Weislogel to propose the two Vane Gap tests in his highly successful Capillary Fluids Experiment (CFE) in the International Space Station in 2006 and 2007[6]. Chen as been involved in the remodeling of these two Vane Gap cylinders for subsequent re-launch to ISS for a second round of experiments expected in 2010 and 2011. In August 2007 the School of Aeronautics and Astronautics at Purdue University moved into the new Neil Armstrong Hall of Engineering and construction on a new 2-second drop tower began. A vertical shaft of nearly 23 meters was designed into the building. An approximately 80 m2 general-use fluids lab is at the top level, and a small access room of approximately 9 m2 is at the bottom. However, construction of the new $57M building created only the space for the science facility, not the science facility itself. The science facility is under construction and this paper presents

  6. Corporate Social Responsibility in the Board Room

    DEFF Research Database (Denmark)

    Knudsen, Jette Steen; Geisler, Kathrine; Ege, Mette

    2013-01-01

    When do board directors pay attention to corporate social responsibility (CSR) issues? Board directors have traditionally focused on maximizing shareholder profit and viewed corporate governance narrowly as a way to meet this goal. They have paid little or no attention to CSR issues because......, the board must have relevant competences that enable members to understand CSR issues. Third, compensation of top-level management should reflect CSR performance. The first two conditions are directly linked to human resource development because, in order to embrace the specific challenges that CSR...

  7. Social Responsibility in the Board Room

    DEFF Research Database (Denmark)

    Ege, Mette; Geisler, Kathrine; Knudsen, Jette Steen

    When do board directors pay attention to corporate social responsibility (CSR) issues? Board directors have traditionally focused on maximizing shareholder profit and viewed corporate governance narrowly as a way to meet this goal. They have paid little or no attention to CSR issues because......, the board must have relevant competences that enable members to understand CSR issues. Third, compensation of top level management should reflect CSR performance. The first two conditions are directly linked to human resource development (HRD) because in order to embrace the specific challenges that CSR...

  8. Decamp Clock Board Firmware

    International Nuclear Information System (INIS)

    Vicente, J. de; Castilla, J.; Martinez, G.

    2007-01-01

    Decamp (Dark Energy Survey Camera) is a new instrument designed to explore the universe aiming to reveal the nature of Dark Energy. The camera consists of 72 CCDs and 520 Mpixels. The readout electronics of DECam is based on the Monsoon system. Monsoon is a new image acquisition system developed by the NOAO (National Optical Astronomical Observatory) for the new generation of astronomical cameras. The Monsoon system uses three types of boards inserted in a Eurocard format based crate: master control board, acquisition board and clock board. The direct use of the Monsoon system for DECam readout electronics requires nine crates mainly due to the high number of clock boards needed. Unfortunately, the available space for DECam electronics is constrained to four crates at maximum. The major drawback to achieve such desired compaction degree resides in the clock board signal density. This document describes the changes performed at CIEMAT on the programmable logic of the Monsoon clock board aiming to meet such restricted space constraints. (Author) 5 refs

  9. Decamp Clock Board Firmware

    Energy Technology Data Exchange (ETDEWEB)

    Vicente, J. de; Castilla, J.; Martinez, G.

    2007-09-27

    Decamp (Dark Energy Survey Camera) is a new instrument designed to explore the universe aiming to reveal the nature of Dark Energy. The camera consists of 72 CCDs and 520 Mpixels. The readout electronics of DECam is based on the Monsoon system. Monsoon is a new image acquisition system developed by the NOAO (National Optical Astronomical Observatory) for the new generation of astronomical cameras. The Monsoon system uses three types of boards inserted in a Eurocard format based crate: master control board, acquisition board and clock board. The direct use of the Monsoon system for DECam readout electronics requires nine crates mainly due to the high number of clock boards needed. Unfortunately, the available space for DECam electronics is constrained to four crates at maximum. The major drawback to achieve such desired compaction degree resides in the clock board signal density. This document describes the changes performed at CIEMAT on the programmable logic of the Monsoon clock board aiming to meet such restricted space constraints. (Author) 5 refs.

  10. Progress on Concepts for Next-Generation Drop Tower Systems

    Science.gov (United States)

    Könemann, Thorben; Eigenbrod, Christian; Von Kampen, Peter; Laemmerzahl, Claus; Kaczmarczik, Ulrich

    2016-07-01

    The Center of Applied Space Technology and Microgravity (ZARM) founded by Prof. Dr.-Ing. Hans J. Rath in 1985 is part of the Department of Production Engineering at the University of Bremen, Germany. ZARM is mainly concentrated on fundamental investigations of gravitational and space-related phenomenas under conditions of weightlessness as well as questions and developments related to technologies for space. At ZARM about 100 scientists, engineers, and administrative staff as well as many students from different departments are employed. Today, ZARM is still one of the largest and most important research center for space sciences and technologies in Europe. With a height of 146 m the Bremen Drop Tower is the predominant facility of ZARM and also the only drop tower of its class in Europe. ZARM's ground-based laboratory offers the opportunity for daily short-term experiments under conditions of high-quality weightlessness at a level of 10-6 g (microgravity), which is one of the best achievable for ground-based flight opportunities. Scientists may choose up to three times a day between a single drop experiment with 4.74 s in simple free fall and an experiment in ZARM's worldwide unique catapult system with 9.3 s in weightlessness. Since the start of operation of the facility in 1990, over 7500 drops or catapult launches of more than 160 different experiment types from various scientific fields like fundamental physics, combustion, fluid dynamics, planetary formation / astrophysics, biology and materials sciences have been accomplished so far. In addition, more and more technology tests have been conducted under microgravity conditions at the Bremen Drop Tower in order to effectively prepare appropriate space missions in advance. In this paper we report on the progress on concepts for next-generation drop tower systems based on the GraviTower idea utilizing a guided electro-magnetic linear drive. Alternative concepts motivated by the scientific demand for higher

  11. Board Effectiveness in Small Firms

    OpenAIRE

    Söderqvist, Anette; Wägar, Karolina

    2010-01-01

    Purpose: This study investigates boards of directors in small firms and explores the link between board effectiveness and the composition, roles and working styles of the boards. Design/methodology/approach: The study analyses data from a telephone survey of boards in 45 small firms. The survey included both the CEO and the chairperson of the board. Findings: The study identifies three groups of small firms: ‘paperboards’, ‘professional boards’, and ‘management lead’ boards. Results show that...

  12. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2008-01-01

    The Joint Advisory Appeals Board has examined the internal appeal lodged by a member of the personnel against the decision to grant him only a periodic one-step advancement for the 2006 reference year. The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the attention of the members of the personnel. In application of Article R VI 1.18 of the Staff Regulations, these documents will therefore be posted on the notice board of the Main building (bldg. 500) from 1 September to 14 September 2008. Human Resources Department (73911)

  13. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2008-01-01

    The Joint Advisory Appeals Board has examined the internal appeal lodged by a member of the personnel with regard to the decision not to grant him an indefinite contract. The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the notice of the members of the personnel. In application of Article R VI 1.18 of the Staff Regulations, these documents will therefore be posted on the notice board of the Main Building (Bldg. 500) from 26 May to 6 June 2008. Human Resources Department (73911)

  14. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2006-01-01

    The Joint Advisory Appeals Board was convened to examine an appeal lodged by a member of the personnel with regard to advancement. The person concerned has requested that the report of the Board and the final decision of the Director-General be brought to the notice of the personnel in accordance with Article R VI 1.20 of the Staff Regulations. The relevant documents will therefore be posted on the notice boards of the Administration Building (No. 60) from 24 March to 10 April 2006. Human Resources Department Tel. 74128

  15. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2008-01-01

    The Joint Advisory Appeals Board has examined the internal appeal lodged by a member of the personnel against the decision to grant him only a periodic one-step advancement for the 2006 reference year. The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the attention of the members of the personnel. In application of Article R VI 1.18 of the Staff Regulations, these documents will therefore be posted on the notice board of the Main Building (Bldg. 500) from 1 September to 14 September 2008. Human Resources Department (73911)

  16. Joint Advisory Appeals Board

    CERN Multimedia

    2003-01-01

    The Joint Advisory Appeals Board was convened to examine the appeal lodged by Mrs Judith Igo-Kemenes concerning the application of procedures foreseen by Administrative Circular N§ 26 (Rev. 3). As the appellant has not objected, the report of the Board and the final decision of the Director-General are brought to the notice of the personnel in accordance with Article R VI 1.20 of the Staff Regulations. The relevant documents will therefore be posted on the notice boards of the Administration Building (N° 60) from 6 to 20 June 2003. Human Resources Division Tel. 74128

  17. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2008-01-01

    The Joint Advisory Appeals Board was convened to examine an internal appeal lodged by a member of the personnel with regard to the decision not to grant him an indefinite contract. The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the notice of the members of the personnel, in accordance with Article R VI 1.18 of the Staff Regulations. These documents will therefore be posted on the notice board of the Main Building (Bldg. 60) from 21 January to 3 February 2008. Human Resources Department (73911)

  18. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2008-01-01

    The Joint Advisory Appeals Board has examined the internal appeal lodged by a member of the personnel with regard to the decision not to award him a periodic one-step advancement for the 2006 reference year. The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the notice of the members of the personnel. In application of Article R VI 1.18 of the Staff Regulations, these documents will therefore be posted on the notice board of the Main building (Bldg. 500) from 17 March to 30 March 2008. Human Resources Department Tel. 73911

  19. Joint Advisory Appeals Board

    CERN Multimedia

    HR Department

    2007-01-01

    The Joint Advisory Appeals Board was convened to examine an internal appeal lodged by a member of the personnel with regard to the decision not to grant him an indefinite contract. The person concerned has requested that the report of the Board and the final decision of the Director-General be brought to the notice of the members of the personnel, in accordance with Article R VI 1.18 of the Staff Regulations. The relevant documents will therefore be posted on the notice board of the Main building (Bldg. 60) from 24 September to 7 October 2007. Human Resources Department

  20. Primer printed circuit boards

    CERN Document Server

    Argyle, Andrew

    2009-01-01

    Step-by-step instructions for making your own PCBs at home. Making your own printed circuit board (PCB) might seem a daunting task, but once you master the steps, it's easy to attain professional-looking results. Printed circuit boards, which connect chips and other components, are what make almost all modern electronic devices possible. PCBs are made from sheets of fiberglass clad with copper, usually in multiplelayers. Cut a computer motherboard in two, for instance, and you'll often see five or more differently patterned layers. Making boards at home is relatively easy

  1. Joint Advisory Appeals Board

    CERN Multimedia

    2003-01-01

    The Joint Advisory Appeals Board was convened to examine the appeal lodged by Mr Aloïs Girardoz with regard to classification and advancement. As the appellant has not objected, the Board's report and the Director-General's decision will be brought to the notice of the personnel in accordance with Article R VI 1.20 of the Staff Regulations. The relevant documents will therefore be posted on the notice boards of the Administration Building (N° 60) from 15 to 29 August 2003. Human Resources Division Tel. 74128

  2. Drop impact splashing and air entrapment

    KAUST Repository

    Thoraval, Marie-Jean

    2013-03-01

    Drop impact is a canonical problem in fluid mechanics, with numerous applications in industrial as well as natural phenomena. The extremely simple initial configuration of the experiment can produce a very large variety of fast and complex dynamics. Scientific progress was made in parallel with major improvements in imaging and computational technologies. Most recently, high-speed imaging video cameras have opened the exploration of new phenomena occurring at the micro-second scale, and parallel computing allowed realistic direct numerical simulations of drop impacts. We combine these tools to bring a new understanding of two fundamental aspects of drop impacts: splashing and air entrapment. The early dynamics of a drop impacting on a liquid pool at high velocity produces an ejecta sheet, emerging horizontally in the neck between the drop and the pool. We show how the interaction of this thin liquid sheet with the air, the drop or the pool, can produce micro-droplets and bubble rings. Then we detail how the breakup of the air film stretched between the drop and the pool for lower impact velocities can produce a myriad of micro-bubbles.

  3. CMS Collaboration Board Meeting

    CERN Multimedia

    Hoch, Michael

    2013-01-01

    The first CMS Collaboration Board meeting of the year (2013) provided an opportunity to thank Teresa Rodrigo, Matthias Kasemann and Randy Ruchti, the 2011-12 CB Chair, Deputy Chair and Secretary, respectively.

  4. Boat boarding ladder placement

    Science.gov (United States)

    1998-04-01

    Presented in three volumes; 'Boat Boarding Ladder Placement,' which explores safety considerations including potential for human contact with a rotating propeller; 'Boat Handhold Placement,' which explores essential principles and methods of fall con...

  5. Checking a printed board

    CERN Multimedia

    1977-01-01

    An 'Interactive Printed Circuit Board Design System' has been developed by a company in a Member-State. Printed circuits are now produced at the SB's surface treatment workshop using a digitized photo-plotter.

  6. Initial Electrospreading of Aqueous Electrolyte Drops

    Science.gov (United States)

    Chen, Longquan; Li, Chunli; van der Vegt, Nico F. A.; Auernhammer, Günter K.; Bonaccurso, Elmar

    2013-01-01

    The early spreading of a liquid drop on a solid surface driven by inertial, capillary, and electrostatic forces is of fundamental interest, since most commonly used surfaces are (naturally) charged. We studied the effect of applying an electric potential between a drop and a surface on the early spreading of aqueous electrolyte drops. We found that spreading dynamics not only depended on the potential, but also on the electrolyte concentration. Based on molecular dynamics simulations of the ion distribution in spreading nanodrops under an applied potential, we propose a simple model to explain the relation between applied potential, electrolyte concentration, and early spreading dynamics.

  7. Board oversight of executive performance and compensation.

    Science.gov (United States)

    Curran, Connie R; Totten, Mary K

    2010-01-01

    Making sure the relative roles of the board and management are clear and agreed upon is becoming more important as market and regulatory forces compel boards to govern at levels of detail once considered micromanagement, but are now required and necessary in the current environment of heightened governance accountability. A clear understanding of each other's roles and responsibilities is step one in building a solid partnership between the board and chief executive. A second element of building a strong foundation for the board-CEO relationship is taking time early on to establish mutual expectations about working together. The board's responsibilities in CEO performance management and compensation include setting performance expectations and goals that are clear and measurable and coaching and motivating the CEO. When a CEO fails, one of the most important steps for the board to take is to look in the mirror and commit to the rigorous due diligence needed to avoid future mistakes. Boards should always have CEO succession on their agenda.

  8. Boarding school rules.

    Science.gov (United States)

    Griffiths, Matt

    2017-01-04

    Ofsted inspects and regulates services that care for children and young people, including boarding facilities. Medication management is an integral part of caring for children in boarding schools, and robust systems must be in place to pass inspection. These systems must cover how medicines are dispensed, administered and stored at the facility, risk assessments, identifying which pupils can manage their own medicines and the individual health needs of boarders, so that care plans can be put in place for children with specific needs.

  9. COLLABORATION BOARD (CB55)

    CERN Multimedia

    B. Cousins

    Open Access Publication Policy ATLAS had recently issued a short statement in support of open access publishing. The mood of the discussions in the December CMS Collaboration Board had appeared to be in favour and so it was being proposed that CMS issue the same statement as that made by ATLAS (the statement is attached to the agenda of this meeting). The Collaboration Board agreed. Election of the Chair of the Collaboration Board Following the agreement to shorten the terms of both the Spokesperson and the Collaboration Board Chair, and to introduce a longer overlap period between the election and the start of the term, the election for the next Collaboration Board Chair was due in December 2007. If the old standard schedule specified in the Constitution were adapted to this date, then the Board should be informed at the present meeting that the election was being prepared. However, it was felt that the experience of the previous year's election of the Spokesperson had shown that it would be desirable to...

  10. Board certification in optometry.

    Science.gov (United States)

    Kirby, B S; Weaver, J L; Amos, J F; Hendrix, W G; Lewis, T L; Locke, J C; McCall, J A; Walls, L L

    2000-04-01

    In keeping with current expectations in the health care community, the purpose of the American Board of Optometric Practice (ABOP) is to enhance the quality of optometric care available to the public by fostering continued competence for practitioners through administering education and examinations for certification and re-certification. The formation of ABOP makes possible for the first time a board certification process for optometrists. The optometry model for board certification and recertification emphasizes the breadth of the profession. ABOP certification will be accomplished through a combination of examinations and high-quality, tested Board Certified Continuing Education (BCCE). Specific requirements for practitioners at various stages of their careers are presented. Board certification provides one important mechanism for an optometrist to demonstrate commitment to quality, professionalism, and ongoing clinical competence. The optometrist benefits from high-quality continuing education designed for timeliness, importance, and breadth. The public benefits by the enhancement of continued competence within the optometric profession. Health care agencies benefit by being able to recognize providers who have elected to demonstrate their qualifications through certification. Through board certification, optometrists will be able to demonstrate their commitment to maintaining clinical competence through a nationally uniform program, and they will be able to comply with standards that are generally recognized and required throughout the health care community.

  11. Social scientist on board in long-term management of high level and/or long-lived radioactive waste in Belgium

    International Nuclear Information System (INIS)

    Parotte, C.

    2013-01-01

    In Belgium, the long-term management of radioactive waste is under the exclusive competence of the Belgian Agency for Radioactive Waste and Enriched Fissile Materials (knew as ONDRAF/NIRAS). Unlike low-level waste, no institutional policy has yet been formally approved for the long-term management of high level and/or long-lived radioactive waste (knew as B and C waste). In this context, ONDRAF/NIRAS considers the public and stakeholders' participation as an essential factor in the formulation of an effective and legitimate policy. This is why it has decided to integrate them in different ways during the elaboration of the Waste Plan (ONDRAF/NIRAS-document containing guidelines to make a principled policy decision about nuclear waste management). To do so, social scientists have been regularly mobilized either as external evaluators, follow-up committee members, or participatory observants. Hence, the Waste Plan is only the first step in a long decision-making process. For a PhD student under contract with ONDRAF/NIRAS, this mandate consists of thinking out a way to construct an inter-organizational innovative communication system that would be participative, transparent and embedded in a long-term perspective, thus integrating all the further legal steps to take throughout the decision-making process. In this regard, two paradoxical constraints must be taken into account: on the one hand, my own influence on the legal decision-making process should remain limited, because of a series of constraints, lock-ins and previous decisions which have to be respected; on the other hand, ONDRAF/NIRAS expects the research conclusions to be policy relevant and useful. In this paper, the purpose is twofold. Firstly, the issues raised by this policy mandate is an opportunity to question the per-formative dimensions of the social scientist in the decision-making process and, more specifically, to have a reflexive view on our position as PhD Student. Secondly, assuming the

  12. Social scientist on board in long-term management of high level and/or long-lived radioactive waste in Belgium

    Energy Technology Data Exchange (ETDEWEB)

    Parotte, C. [Spiral Research Center, Department of Political Sciences, Faculty of Law, University of Liege (Belgium)

    2013-07-01

    In Belgium, the long-term management of radioactive waste is under the exclusive competence of the Belgian Agency for Radioactive Waste and Enriched Fissile Materials (knew as ONDRAF/NIRAS). Unlike low-level waste, no institutional policy has yet been formally approved for the long-term management of high level and/or long-lived radioactive waste (knew as B and C waste). In this context, ONDRAF/NIRAS considers the public and stakeholders' participation as an essential factor in the formulation of an effective and legitimate policy. This is why it has decided to integrate them in different ways during the elaboration of the Waste Plan (ONDRAF/NIRAS-document containing guidelines to make a principled policy decision about nuclear waste management). To do so, social scientists have been regularly mobilized either as external evaluators, follow-up committee members, or participatory observants. Hence, the Waste Plan is only the first step in a long decision-making process. For a PhD student under contract with ONDRAF/NIRAS, this mandate consists of thinking out a way to construct an inter-organizational innovative communication system that would be participative, transparent and embedded in a long-term perspective, thus integrating all the further legal steps to take throughout the decision-making process. In this regard, two paradoxical constraints must be taken into account: on the one hand, my own influence on the legal decision-making process should remain limited, because of a series of constraints, lock-ins and previous decisions which have to be respected; on the other hand, ONDRAF/NIRAS expects the research conclusions to be policy relevant and useful. In this paper, the purpose is twofold. Firstly, the issues raised by this policy mandate is an opportunity to question the per-formative dimensions of the social scientist in the decision-making process and, more specifically, to have a reflexive view on our position as PhD Student. Secondly, assuming the

  13. 14 CFR 382.101 - What other boarding and deplaning assistance must carriers provide?

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false What other boarding and deplaning... DISABILITY IN AIR TRAVEL Boarding, Deplaning, and Connecting Assistance § 382.101 What other boarding and deplaning assistance must carriers provide? When level-entry boarding and deplaning assistance is not...

  14. Micro-splashing by drop impacts

    KAUST Repository

    Thoroddsen, Sigurdur T.

    2012-07-18

    We use ultra-high-speed video imaging to observe directly the earliest onset of prompt splashing when a drop impacts onto a smooth solid surface. We capture the start of the ejecta sheet travelling along the solid substrate and show how it breaks up immediately upon emergence from the underneath the drop. The resulting micro-droplets are much smaller and faster than previously reported and may have gone unobserved owing to their very small size and rapid ejection velocities, which approach 100 m s-1, for typical impact conditions of large rain drops. We propose a phenomenological mechanism which predicts the velocity and size distribution of the resulting microdroplets. We also observe azimuthal undulations which may help promote the earliest breakup of the ejecta. This instability occurs in the cusp in the free surface where the drop surface meets the radially ejected liquid sheet. © 2012 Cambridge University Press.

  15. Blood drop patterns: Formation and applications.

    Science.gov (United States)

    Chen, Ruoyang; Zhang, Liyuan; Zang, Duyang; Shen, Wei

    2016-05-01

    The drying of a drop of blood or plasma on a solid substrate leads to the formation of interesting and complex patterns. Inter- and intra-cellular and macromolecular interactions in the drying plasma or blood drop are responsible for the final morphologies of the dried patterns. Changes in these cellular and macromolecular components in blood caused by diseases have been suspected to cause changes in the dried drop patterns of plasma and whole blood, which could be used as simple diagnostic tools to identify the health of humans and livestock. However, complex physicochemical driving forces involved in the pattern formation are not fully understood. This review focuses on the scientific development in microscopic observations and pattern interpretation of dried plasma and whole blood samples, as well as the diagnostic applications of pattern analysis. Dried drop patterns of plasma consist of intricate visible cracks in the outer region and fine structures in the central region, which are mainly influenced by the presence and concentration of inorganic salts and proteins during drying. The shrinkage of macromolecular gel and its adhesion to the substrate surface have been thought to be responsible for the formation of the cracks. Dried drop patterns of whole blood have three characteristic zones; their formation as functions of drying time has been reported in the literature. Some research works have applied engineering treatment to the evaporation process of whole blood samples. The sensitivities of the resultant patterns to the relative humidity of the environment, the wettability of the substrates, and the size of the drop have been reported. These research works shed light on the mechanisms of spreading, evaporation, gelation, and crack formation of the blood drops on solid substrates, as well as on the potential applications of dried drop patterns of plasma and whole blood in diagnosis. Crown Copyright © 2016. Published by Elsevier B.V. All rights reserved.

  16. Pressure drop in flashing flow through obstructions

    International Nuclear Information System (INIS)

    Weinle, M.E.; Johnston, B.S.

    1985-01-01

    An experiment was designed to investigate the pressure drop for flashing flow across obstructions of different geometries at various flow rates. Tests were run using two different orifices to determine if the two-phase pressure drop could be characterized by the single phase loss coefficient and the general behavior of the two-phase multiplier. For the geometries studied, it was possible to correlate the multiplier in a geometry-independent fashion

  17. Board diversity and sustainability performance

    African Journals Online (AJOL)

    kirstam

    of a trend analysis to compare the differences in board composition between a sample of ... 15Key words: sustainability, sustainability performance, boards of directors, board diversity, corporate governance, SRI index, director background, King Report, integrative model of board performance, corporate social responsibility.

  18. Board Certification in Counseling Psychology

    Science.gov (United States)

    Crowley, Susan L.; Lichtenberg, James W.; Pollard, Jeffrey W.

    2012-01-01

    Although specialty board certification by the American Board of Professional Psychology (ABPP) has been a valued standard for decades, the vast majority of counseling psychologists do not pursue board certification in the specialty. The present article provides a brief history of board certification in general and some historical information about…

  19. Board Governance: Transformational Approaches Under Healthcare Reform.

    Science.gov (United States)

    Zastocki, Deborah K

    2015-01-01

    Previous successes of healthcare organizations and effective governance practices in the pre-reform environment are not predictive of future success. Healthcare has been through numerous phases of growth and development using tried-and-true strategies. The challenge is that our toolbox does not contain what is needed to build the future healthcare delivery systems required in the post-reform world. Healthcare has had a parochial focus at the local level, with some broadening of horizons at the state and national levels. But healthcare delivery is now a global issue that requires a totally different perspective, and many countries are confronting similar issues. US healthcare reform initiatives have far-reaching implications. Compounding the reform dynamics are the simultaneously occurring, gamechanging accelerants such as enabling information technologies and mobile health, new providers of healthcare, increased consumer demands, and limited healthcare dollars, to name a few. Operating in this turbulent environment requires transformational board, executive, and physician leadership because traditional ways of planning for incremental change and attempting to time those adjustments can prove disastrous. Creating the legacy healthcare system for tomorrow requires governing boards and executive leadership to act today as they would in the desired future system. Boards need to create a culture that fosters.innovation with a tolerance for risk and some failure. To provide effective governance, boards must essentially develop new skills, expertise, and ways of thinking. The rapid rate of change requires board members to possess certain capabilities, including the ability to deal with ambiguity and uncertainty while demonstrating flexibility and adaptability, all with a driving commitment to metrics and results. This requires development plans for both individual members and the overall board. In short, the board needs to function differently, particularly regarding the

  20. Microgravity Experiment Programs for Students at the Bremen Drop Tower

    Science.gov (United States)

    Könemann, Thorben; Eigenbrod, Christian; Von Kampen, Peter; Laemmerzahl, Claus

    The Center of Applied Space Technology and Microgravity (ZARM) founded by Prof. Dr.-Ing. Hans J. Rath in 1985 is part of the Department of Production Engineering at the University of Bremen, Germany. ZARM established as a research center and currently headed by Prof. Dr. Claus Lämmerzahl is mainly concentrated on fundamental investigations of gravitational and space-related phenomenas under conditions of weightlessness as well as questions and developments related to technologies for space. At ZARM more than 70 scientists, engineers and administrative staff as well as many students from different departments are employed. Today, ZARM is still one of the largest and most important university institutes for space sciences and technologies in Europe as well as worldwide well known in the space community. With a height of 146 m the Bremen Drop Tower is the predominant facility of ZARM and also the only drop tower of its class in Europe. ZARM’s ground-based laboratory offers the opportunity for daily short-term experiments under conditions of high-quality weightlessness at a level of 10 (-6) g (microgravity). The provided quality is one of the purest for experiments under weightlessness worldwide achieved. The scientists may choose between a single drop experiment with 4.74 s in simple free fall and a catapult experiment with 9.3 s of weightlessness. Either in the drop or in the worldwide unique catapult operation routine the repetition rates of microgravity experiments at ZARM are always the same, generally up to 3 times per day. Since the start of operation of the facility in 1990, over 6750 launches of more than 160 different experiment types from various scientific fields like Fundamental Physics, Combustion, Fluid Dynamics, Planetary Formation / Astrophysics, Biology and Materials Sciences have been successfully accomplished so far. In our paper we will report and inform about microgravity experiment programs for students like "Drop Your Thesis!“ by ESA and

  1. The Drop Tower Bremen -Experiment Operation

    Science.gov (United States)

    Könemann, Thorben; von Kampen, Peter; Rath, Hans J.

    The idea behind the drop tower facility of the Center of Applied Space Technology and Micro-gravity (ZARM) in Bremen is to provide an inimitable technical opportunity of a daily access to short-term weightlessness on earth. In this way ZARM`s european unique ground-based microgravity laboratory displays an excellent economic alternative for research in space-related conditions at low costs comparable to orbital platforms. Many national and international ex-perimentalists motivated by these prospects decide to benefit from the high-quality and easy accessible microgravity environment only provided by the Drop Tower Bremen. Corresponding experiments in reduced gravity could open new perspectives of investigation methods and give scientists an impressive potential for a future technology and multidisciplinary applications on different research fields like Fundamental Physics, Astrophysics, Fluid Dynamics, Combus-tion, Material Science, Chemistry and Biology. Generally, realizing microgravity experiments at ZARM`s drop tower facility meet new requirements of the experimental hardware and may lead to some technical constraints in the setups. In any case the ZARM Drop Tower Operation and Service Company (ZARM FAB mbH) maintaining the drop tower facility is prepared to as-sist experimentalists by offering own air-conditioned laboratories, clean rooms, workshops and consulting engineers, as well as scientific personal. Furthermore, ZARM`s on-site apartment can be used for accommodations during the experiment campaigns. In terms of approaching drop tower experimenting, consulting of experimentalists is mandatory to successfully accomplish the pursued drop or catapult capsule experiment. For this purpose there will be a lot of expertise and help given by ZARM FAB mbH in strong cooperation to-gether with the experimentalists. However, in comparison to standard laboratory setups the drop or catapult capsule setup seems to be completely different at first view. While defining a

  2. [Optimize dropping process of Ginkgo biloba dropping pills by using design space approach].

    Science.gov (United States)

    Shen, Ji-Chen; Wang, Qing-Qing; Chen, An; Pan, Fang-Lai; Gong, Xing-Chu; Qu, Hai-Bin

    2017-07-01

    In this paper, a design space approach was applied to optimize the dropping process of Ginkgo biloba dropping pills. Firstly, potential critical process parameters and potential process critical quality attributes were determined through literature research and pre-experiments. Secondly, experiments were carried out according to Box-Behnken design. Then the critical process parameters and critical quality attributes were determined based on the experimental results. Thirdly, second-order polynomial models were used to describe the quantitative relationships between critical process parameters and critical quality attributes. Finally, a probability-based design space was calculated and verified. The verification results showed that efficient production of Ginkgo biloba dropping pills can be guaranteed by operating within the design space parameters. The recommended operation ranges for the critical dropping process parameters of Ginkgo biloba dropping pills were as follows: dropping distance of 5.5-6.7 cm, and dropping speed of 59-60 drops per minute, providing a reference for industrial production of Ginkgo biloba dropping pills. Copyright© by the Chinese Pharmaceutical Association.

  3. Stress Drops for Potentially Induced Earthquake Sequences

    Science.gov (United States)

    Huang, Y.; Beroza, G. C.; Ellsworth, W. L.

    2015-12-01

    Stress drop, the difference between shear stress acting across a fault before and after an earthquake, is a fundamental parameter of the earthquake source process and the generation of strong ground motions. Higher stress drops usually lead to more high-frequency ground motions. Hough [2014 and 2015] observed low intensities in "Did You Feel It?" data for injection-induced earthquakes, and interpreted them to be a result of low stress drops. It is also possible that the low recorded intensities could be a result of propagation effects. Atkinson et al. [2015] show that the shallow depth of injection-induced earthquakes can lead to a lack of high-frequency ground motion as well. We apply the spectral ratio method of Imanishi and Ellsworth [2006] to analyze stress drops of injection-induced earthquakes, using smaller earthquakes with similar waveforms as empirical Green's functions (eGfs). Both the effects of path and linear site response should be cancelled out through the spectral ratio analysis. We apply this technique to the Guy-Greenbrier earthquake sequence in central Arkansas. The earthquakes migrated along the Guy-Greenbrier Fault while nearby injection wells were operating in 2010-2011. Huang and Beroza [GRL, 2015] improved the magnitude of completeness to about -1 using template matching and found that the earthquakes deviated from Gutenberg-Richter statistics during the operation of nearby injection wells. We identify 49 clusters of highly similar events in the Huang and Beroza [2015] catalog and calculate stress drops using the source model described in Imanishi and Ellsworth [2006]. Our results suggest that stress drops of the Guy-Greenbrier sequence are similar to tectonic earthquakes at Parkfield, California (the attached figure). We will also present stress drop analysis of other suspected induced earthquake sequences using the same method.

  4. JOINT ADVISORY APPEALS BOARD

    CERN Multimedia

    Human Resources Division

    2001-01-01

    The Joint Advisory Appeals Board was convened to examine the appeal lodged by Mr Neil Calder, Mrs Sudeshna Datta Cockerill, Mrs Andrée Fontbonne, Mrs Moniek Laurent and Mr Ulrich Liptow with regard to membership in the Pension Fund under the period with a Paid Associate contract, appeals dealt with on a collective basis. As the appellants have not objected, the report of the Board and the final decision of the Director-General are brought to the notice of the personnel in accordance with Article R VI 1.20 of the Staff Regulations. The relevant documents will therefore be posted on the notice boards of the Administration Building (N° 60) from 10 to 31 August 2001.

  5. Pension Fund Governing Board

    CERN Multimedia

    HR Department

    2008-01-01

    Note The CERN pension scheme is based on the principle of defined benefits, so beneficiaries continue to receive the benefits to which they are entitled in accordance with the Rules of the Pension Fund. This means that pension entitlements under the Rules are not directly affected by the financial crisis and the current economic situation. However, the adjustment of pensions to the cost of living is not automatic and, under the method applied since 2006, must take into account the Fund’s financial position. Meeting of the Pension Fund Governing Board The Pension Fund Governing Board held its eighth meeting at ESO in Garching, Germany (near Munich) on 24 October 2008. Before starting its work, the Governing Board had the privilege of hearing an opening address by Professor Tim de Zeeuw, the Director General of ESO. Professor de Zeeuw described the mission of ESO and the ambitious projects of his organisation, which performs astronomy observations using telescopes located in...

  6. New Service Status Board

    CERN Multimedia

    2013-01-01

    On Monday 14 October, the Service Status Board for GS and IT will change. The new Status Board will be integrated with the CERN Service Portal and with the CERN Service Catalogue.   As of today, the SSB will display “Service Incidents”, “Planned Interventions” and “Service Changes”. References valid from 14 October: CERN SSB at https://cern.ch/ssb Computing SSB (previously IT SSB) at https://cern.ch/itssb   Nicole Cremel, IT and GS Service Management Support

  7. Joint Advisory Appeals Board

    CERN Multimedia

    2013-01-01

    The Joint Advisory Appeals Board has examined the internal appeal lodged by a former member of the personnel, a beneficiary of the CERN Pension Fund, against the calculation of his pension in the framework of the Progressive Retirement Programme.   The person concerned has not objected to the report of the Board and the final decision of the Director-General being brought to the attention of the members of the personnel. In application of Article R VI 1.18 of the Staff Regulations, these documents will therefore be available from 26 July to 11 August 2013 at the following link. HR Department Head Office

  8. Drop impact entrapment of bubble rings

    KAUST Repository

    Thoraval, M.-J.

    2013-04-29

    We use ultra-high-speed video imaging to look at the initial contact of a drop impacting on a liquid layer. We observe experimentally the vortex street and the bubble-ring entrapments predicted numerically, for high impact velocities, by Thoraval et al. (Phys. Rev. Lett., vol. 108, 2012, article 264506). These dynamics mainly occur within 50 -s after the first contact, requiring imaging at 1 million f.p.s. For a water drop impacting on a thin layer of water, the entrapment of isolated bubbles starts through azimuthal instability, which forms at low impact velocities, in the neck connecting the drop and pool. For Reynolds number Re above -12 000, up to 10 partial bubble rings have been observed at the base of the ejecta, starting when the contact is -20% of the drop size. More regular bubble rings are observed for a pool of ethanol or methanol. The video imaging shows rotation around some of these air cylinders, which can temporarily delay their breakup into micro-bubbles. The different refractive index in the pool liquid reveals the destabilization of the vortices and the formation of streamwise vortices and intricate vortex tangles. Fine-scale axisymmetry is thereby destroyed. We show also that the shape of the drop has a strong influence on these dynamics. 2013 Cambridge University Press.

  9. Drop Testing Representative Multi-Canister Overpacks

    Energy Technology Data Exchange (ETDEWEB)

    Snow, Spencer D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Morton, Dana K. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-06-01

    The objective of the work reported herein was to determine the ability of the Multi- Canister Overpack (MCO) canister design to maintain its containment boundary after an accidental drop event. Two test MCO canisters were assembled at Hanford, prepared for testing at the Idaho National Engineering and Environmental Laboratory (INEEL), drop tested at Sandia National Laboratories, and evaluated back at the INEEL. In addition to the actual testing efforts, finite element plastic analysis techniques were used to make both pre-test and post-test predictions of the test MCOs structural deformations. The completed effort has demonstrated that the canister design is capable of maintaining a 50 psig pressure boundary after drop testing. Based on helium leak testing methods, one test MCO was determined to have a leakage rate not greater than 1x10-5 std cc/sec (prior internal helium presence prevented a more rigorous test) and the remaining test MCO had a measured leakage rate less than 1x10-7 std cc/sec (i.e., a leaktight containment) after the drop test. The effort has also demonstrated the capability of finite element methods using plastic analysis techniques to accurately predict the structural deformations of canisters subjected to an accidental drop event.

  10. Spread of pathogens through rain drop impact

    Science.gov (United States)

    Kim, Seungho; Gruszewski, Hope; Gidley, Todd; Schmale, David G., III; Jung, Sunghwan

    2017-11-01

    Rain drop impact can disperse micron-sized pathogenic particles over long distances. In this study, we aim to elucidate mechanisms for disease dispersal when a rain drop impacts a particle-laden solid surface. Three different dispersal types were observed depending on whether the dispersed glass particles were dry or wet. For a dry particle dispersal, the movement of contact line made the particles initially jump off the surface with relatively high velocity. Then, air vortex was formed due to the air current entrained along with the falling drop, and advected the particles with relatively low velocity. For a wet particle dispersal, the contact line of a spreading liquid became unstable due to the presence of the particles on the substrate. This caused splashing at the contact line and ejected liquid droplets carrying the particles. Finally, we released a drop onto wheat plants infected with the rust fungus, Puccinia triticina, and found that nearly all of the satellite droplets from a single drop contained at least one rust spore. Also, we visualized such novel dispersal dynamics with a high-speed camera and characterized their features by scaling models. This research was partially supported by National Science Foundation Grant CBET-1604424.

  11. Drop impact on spherical soft surfaces

    Science.gov (United States)

    Chen, Simeng; Bertola, Volfango

    2017-08-01

    The impact of water drops on spherical soft surfaces is investigated experimentally through high-speed imaging. The effect of a convex compliant surface on the dynamics of impacting drops is relevant to various applications, such as 3D ink-jet printing, where drops of fresh material impact on partially cured soft substrates with arbitrary shape. Several quantities which characterize the morphology of impacting drops are measured through image-processing, including the maximum and minimum spreading angles, length of the wetted curve, and dynamic contact angle. In particular, the dynamic contact angle is measured using a novel digital image-processing scheme based on a goniometric mask, which does not require edge fitting. It is shown that the surface with a higher curvature enhances the retraction of the spreading drop; this effect may be due to the difference of energy dissipation induced by the curvature of the surface. In addition, the impact parameters (elastic modulus, diameter ratio, and Weber number) are observed to significantly affect the dynamic contact angle during impact. A quantitative estimation of the deformation energy shows that it is significantly smaller than viscous dissipation.

  12. The Board's Demography-Firm Performance Relationship Revisited: A Bayesian Approach

    OpenAIRE

    Huybrechts, Jolien; Voordeckers, Wim; D'Espallier, Bert; Lybaert, Nadine; Van Gils, Anita

    2016-01-01

    Building on behavioral theory, we argue that the effect of board demography on the performance of small and medium-sized family firms differs significantly at the individual firm level and that the degree by which board task performance meets board task needs explains this effect. Using a Bayesian estimation method, we obtain firm specific estimates of the effect of board demography on firm performance. Analysis of these estimates indicates that the size of the gap between board task needs an...

  13. Hydrodynamic shrinkage of liquid CO2 Taylor drops in a straight microchannel

    Science.gov (United States)

    Qin, Ning; Wen, John Z.; Ren, Carolyn L.

    2018-03-01

    Hydrodynamic shrinkage of liquid CO2 drops in water under a Taylor flow regime is studied using a straight microchannel (length/width ~100). A general form of a mathematical model of the solvent-side mass transfer coefficient (k s) is developed first. Based on formulations of the surface area (A) and the volume (V) of a general Taylor drop in a rectangular microchannel, a specific form of k s is derived. Drop length and speed are experimentally measured at three specified positions of the straight channel, namely, immediately after drop generation (position 1), the midpoint of the channel (position 2) and the end of the channel (position 3). The reductions of drop length (L x , x  =  1, 2, 3) from position 1 to 2 and down to 3 are used to quantify the drop shrinkage. Using the specific model, k s is calculated mainly based on L x and drop flowing time (t). Results show that smaller CO2 drops produced by lower flow rate ratios ({{Q}LC{{O2}}}/{{Q}{{H2}O}} ) are generally characterized by higher (nearly three times) k s and Sherwood numbers than those produced by higher {{Q}LC{{O2}}}/{{Q}{{H2}O}} , which is essentially attributed to the larger effective portion of the smaller drop contributing in the mass transfer under same levels of the flowing time and the surface-to-volume ratio (~104 m-1) of all drops. Based on calculated pressure drops of the segmented flow in microchannel, the Peng-Robinson equation of state and initial pressures of drops at the T-junction in experiments, overall pressure drop (ΔP t) in the straight channel as well as the resulted drop volume change are quantified. ΔP t from position 1-3 is by average 3.175 kPa with a ~1.6% standard error, which only leads to relative drop volume changes of 0.3‰ to 0.52‰.

  14. Magnesium-oxide boards cause moisture damage inside facades in new Danish buildings

    DEFF Research Database (Denmark)

    Hansen, Kurt Kielsgaard; Bunch-Nielsen, Tommy; Grelk, Bent

    2016-01-01

    Magnesium oxide board, “MgO-board”, is a factory-made sheathing board product, which has been widely used in the last 5 years in ventilated facades on new or renovated buildings in Denmark. In winter 2014/15, a number of problems began to appear with these boards since the boards and adjoining...... in periods with high outdoor humidity (90-100% RH) and form water drops on the surfaces. The drops contain a high amount of soluble chloride ions and appear on the surfaces of the boards and may often run down the boards and to adjacent structures. Metal fixtures for the MgO-and siding boards may corrode...... heavily within a few years. The binder in MgO-boards is formed by chemical reaction between MgO and MgCl2, known as magnesium oxychloride cement or Sorel cement. Also organic matter can be found in the material. The paper presents results of investigations of properties for moisture ab- and desorption...

  15. A drop penetration method to measure powder blend wettability.

    Science.gov (United States)

    Wang, Yifan; Liu, Zhanjie; Muzzio, Fernando; Drazer, German; Callegari, Gerardo

    2018-03-01

    Water wettability of pharmaceutical blends affects important quality attributes of final products. We investigate the wetting properties of a pharmaceutical blend lubricated with Magnesium Stearate (MgSt) as a function of the mechanical shear strain applied to the blend. We measure the penetration dynamics of sessile drops deposited on slightly compressed powder beds. We consider a blend composed of 9% Acetaminophen 90% Lactose and 1% MgSt by weight. Comparing the penetration time of water and a reference liquid Polydimethylsiloxane (silicon oil) we obtain an effective cosine of the contact angle with water, based on a recently developed drop penetration method. We repeat the experiments for blends exposed to increasing levels of shear strain and demonstrate a significant decrease in water wettability (decrease in the cosine of the contact angle). The results are consistent with the development of a hydrophobic film coating the powder particles as a result of the increased shear strain. Finally, we show that, as expected dissolution times increase with the level of shear strain. Therefore, the proposed drop penetration method could be used to directly assess the state of lubrication of a pharmaceutical blend and act as a quality control on powder blend attributes before the blend is tableted. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Application of Hanging Drop Technique for Kidney Tissue Culture.

    Science.gov (United States)

    Wang, Shaohui; Wang, Ximing; Boone, Jasmine; Wie, Jin; Yip, Kay-Pong; Zhang, Jie; Wang, Lei; Liu, Ruisheng

    2017-01-01

    The hanging drop technique is a well-established method used in culture of animal tissues. However, this method has not been used in adult kidney tissue culture yet. This study was to explore the feasibility of using this technique for culturing adult kidney cortex to study the time course of RNA viability in the tubules and vasculature, as well as the tissue structural integrity. In each Petri dish with the plate covered with sterile buffer, a section of mouse renal cortex was cultured within a drop of DMEM culture medium on the inner surface of the lip facing downward. The tissue were then harvested at each specific time points for Real-time PCR analysis and histological studies. The results showed that the mRNA level of most Na+ related transporters and cotransporters were stably maintained within 6 hours in culture, and that the mRNA level of most receptors found in the vasculature and glomeruli were stably maintained for up to 9 days in culture. Paraffin sections of the cultured renal cortex indicated that the tubules began to lose tubular integrity after 6 hours, but the glomeruli and vasculatures were still recognizable up to 9 days in culture. We concluded that adult kidney tissue culture by hanging drop method can be used to study gene expressions in vasculature and glomeruli. © 2017 The Author(s). Published by S. Karger AG, Basel.

  17. Development of Active Learning Curriculum for CASPER's Microgravity Drop Tower

    Science.gov (United States)

    Carmona-Reyes, Jorge; Wang, Li; York, Judy; Matthews, Lorin; Laufer, Rene; Cook, Mike; Schmoke, Jimmy; Hyde, Truell

    2016-10-01

    As CASPER's new drop tower comes on line, plans for correlated educational research curricula are underway. CASPER's educational research team is working on developing curricula specific to the CASPER drop tower, modeled on a contest currently in use by (BEST) Robotics Inc. within central Texas independent school districts. The curricula integrates age specific use of computer programming software packages such as ``Scratch'' with industry standard communication protocols and augmented reality applications. Content is constructed around an earth and space science framework, covering subjects such as stars and galaxies, matter and energy, fusion and fission at a middle school level. CASPER faculty are partnering with the Region 12 Service Center; this combination provides a wide range of expertise that includes professional development, pedagogical methods, computational thinking in addition to microgravity and space science research expertise. The details of this work will be presented and samples of the manner in which it is impacting the CASPER research and educational outreach partnership will be discussed.

  18. DC potential drop method for evaluating material degradation

    International Nuclear Information System (INIS)

    Seok, Chang Sung; Bae, Bong Kook; Koo, Jae Mean

    2004-01-01

    The remaining life estimation for the aged components in power plants as well as chemical plants are very important because mechanical properties of the components are degraded with in-service exposure time in high temperatures. Since it is difficult to take specimens from the operating components to evaluate mechanical properties of components, nondestructive techniques are needed to evaluate the degradation. In this study, test materials with several different degradation levels were prepared by isothermal aging heat treatment at 630 .deg. C. The DC potential drop method and destructive methods such as tensile and fracture toughness were used in order to evaluate the degradation of 1Cr-1Mo-0.25V steels. In this result, we can see that tensile strength and fracture toughness can be calculated from resistivity and it is possible to evaluate material degradation using DC potential drop method, non-destructive method

  19. Pressure drop and He II flow through fine mesh screens

    Science.gov (United States)

    Maddocks, J. R.; van Sciver, S. W.

    1989-05-01

    Fluid acquisition systems for He II transfer devices will utilize gallery arms to ensure that the fluid encounters the pump inlet. In near term experiments such as Superfluid Helium on Orbit Transfer (SHOOT), the preferred configuration consists of several rectangular channels which have one side made from a Dutch weave stainless steel screen having 325 x 2300 wires per inch. The effective pore diameter for this screen is about 5 microns. The present paper reports on measurements of pressure drop across a screen when it is subjected to a flow of liquid helium. The experiment measures the time rate of change of the level in two different helium reservoirs connected by a screen-blocked channel. Results with normal helium are compared with predictions based on the Armour-Cannon (1968) equations. The He II data show considerable deviation from the classical result. A discussion of the He II pressure drop results in terms of two fluid hydrodynamics is included.

  20. Ultrasonic characterization of single drops of liquids

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, Dipen N. (Los Alamos, NM)

    1998-01-01

    Ultrasonic characterization of single drops of liquids. The present invention includes the use of two closely spaced transducers, or one transducer and a closely spaced reflector plate, to form an interferometer suitable for ultrasonic characterization of droplet-size and smaller samples without the need for a container. The droplet is held between the interferometer elements, whose distance apart may be adjusted, by surface tension. The surfaces of the interferometer elements may be readily cleansed by a stream of solvent followed by purified air when it is desired to change samples. A single drop of liquid is sufficient for high-quality measurement. Examples of samples which may be investigated using the apparatus and method of the present invention include biological specimens (tear drops; blood and other body fluid samples; samples from tumors, tissues, and organs; secretions from tissues and organs; snake and bee venom, etc.) for diagnostic evaluation, samples in forensic investigations, and detection of drugs in small quantities.

  1. Superheated drop as a neutron spectrometer

    Science.gov (United States)

    Das, Mala; Chatterjee, B. K.; Roy, B.; Roy, S. C.

    2000-09-01

    Superheated drops are known to vaporise when exposed to energetic nuclear radiation since the discovery of bubble chamber. The application of superheated drops in neutron research especially in neutron dosimetry is a subject of intense research for quite sometime. As the degree of superheat increases in a given liquid, less and less energetic neutrons are required to cause nucleation. This property of superheated liquid makes it possible to use it as a neutron spectrometer. Neutron detection efficiency of superheated drops made of R12 exposed to Am-Be neutron source has been measured over a wide range of temperature -17-60°C and the results have been utilised to construct the energy spectrum of the neutron source. This paper demonstrates that a suitable neutron spectrometer may be constructed by using a single liquid and varying the temperature of the liquid suitably at a closer grid.

  2. Superheated drop as a neutron spectrometer

    Energy Technology Data Exchange (ETDEWEB)

    Das, Mala; Chatterjee, B.K.; Roy, B. E-mail: biva@bosemain.boseinst.ernet.in; Roy, S.C

    2000-09-21

    Superheated drops are known to vaporise when exposed to energetic nuclear radiation since the discovery of bubble chamber. The application of superheated drops in neutron research especially in neutron dosimetry is a subject of intense research for quite sometime. As the degree of superheat increases in a given liquid, less and less energetic neutrons are required to cause nucleation. This property of superheated liquid makes it possible to use it as a neutron spectrometer. Neutron detection efficiency of superheated drops made of R12 exposed to Am-Be neutron source has been measured over a wide range of temperature -17-60 deg. C and the results have been utilised to construct the energy spectrum of the neutron source. This paper demonstrates that a suitable neutron spectrometer may be constructed by using a single liquid and varying the temperature of the liquid suitably at a closer grid.

  3. Tunable Transport of Drops on a Vibrating Fiber

    Science.gov (United States)

    Bick, Alison; Sauret, Alban; Boulogne, Francois; Stone, Howard

    2014-11-01

    Transport of liquid drops on a fibrous medium is common in engineering systems such as fog harvesting and textile cleaning. The control of the drop movement on fibrous media can make these engineering systems more efficient. We investigated how to move drops along a single inclined fiber by controlling fiber vibration. Drop motion: static, sliding or falling, depends on the fiber inclination angle, drop volume, and the distance of the drop from the vibrating source. Specifically, by vibrating the fiber the transition between the three drop motion states can be controlled. By defining the response of drop movement to vibration frequency, we can model the drop movement transition. This knowledge is directly useful for controlling drop movement on the fiber. In particular, we experimentally demonstrated that vibration frequency can be used to transport a drop along a fiber.

  4. On-board Data Mining

    Science.gov (United States)

    Tanner, Steve; Stein, Cara; Graves, Sara J.

    Networks of remote sensors are becoming more common as technology improves and costs decline. In the past, a remote sensor was usually a device that collected data to be retrieved at a later time by some other mechanism. This collected data were usually processed well after the fact at a computer greatly removed from the in situ sensing location. This has begun to change as sensor technology, on-board processing, and network communication capabilities have increased and their prices have dropped. There has been an explosion in the number of sensors and sensing devices, not just around the world, but literally throughout the solar system. These sensors are not only becoming vastly more sophisticated, accurate, and detailed in the data they gather but they are also becoming cheaper, lighter, and smaller. At the same time, engineers have developed improved methods to embed computing systems, memory, storage, and communication capabilities into the platforms that host these sensors. Now, it is not unusual to see large networks of sensors working in cooperation with one another. Nor does it seem strange to see the autonomous operation of sensorbased systems, from space-based satellites to smart vacuum cleaners that keep our homes clean and robotic toys that help to entertain and educate our children. But access to sensor data and computing power is only part of the story. For all the power of these systems, there are still substantial limits to what they can accomplish. These include the well-known limits to current Artificial Intelligence capabilities and our limited ability to program the abstract concepts, goals, and improvisation needed for fully autonomous systems. But it also includes much more basic engineering problems such as lack of adequate power, communications bandwidth, and memory, as well as problems with the geolocation and real-time georeferencing required to integrate data from multiple sensors to be used together.

  5. Shuttlecock Velocity of a Badminton Drop Shot

    Directory of Open Access Journals (Sweden)

    Ampharin Ongvises

    2013-12-01

    Full Text Available In a badminton ‘drop shot’, the shuttlecock is struck by a non-rotating racquet at low speed. In this investigation, a shuttlecock was hit by a badminton racquet in a linear collision, simulating a drop shot. The collision was recorded with high-speed video and the velocities of the racquet and shuttlecock determined. The relationship between the impact velocity of the racquet and the velocity of the shuttlecock as it leaves the badminton racquet after collision was found to be proportional over the range tested.

  6. Four-point potential drop measurements for materials characterization

    Science.gov (United States)

    Bowler, Nicola

    2011-01-01

    The technique of measuring the voltage difference (potential drop) between two of the four electrodes of a four-point probe, in order to determine conductivity or surface resistivity of a test piece, is well established in the direct-current (dc) or quasi-dc regime. The technique finds wide usage in the semiconductor industry for the purpose of measuring surface resistivity of semiconductors, and also in the measurement of conductivity of metals, particularly of ferromagnetic metals for which conductivity cannot be easily measured using eddy-current nondestructive evaluation (NDE). In these applications, the conductivity of the test piece is deduced from an analytic formula that depends on the geometry of the probe and test piece. Such a formula requires, as an input, the measured value of the potential drop. Several analytical expressions exist for a variety of test-piece geometries and probe arrangements. Recently, it has been shown that broadband measurements of the potential drop, known as 'alternating current potential drop' (ac PD) measurements, can be used not only to obtain the conductivity of a test piece, but also its linear permeability μ. The beauty of this measurement is that the two parameters are completely decoupled in the quasi-static regime. In fact, μ does not appear in the quasi-static expression for σ. Hence, σ may be obtained from low-frequency ac PD measurements and then μ may be deduced as the frequency increases beyond the quasi-static regime, once σ is known. In this review, both dc and ac solutions that are useful in determining the conductivity of metals and semiconductors, and the permeability of ferromagnetic conductors, are summarized. In particular, flat test pieces with arbitrary thickness are considered. At the next level of complexity, a solution for a half-space coated with a surface layer is given, along with a discussion of the use of the four-point potential drop method for determining thickness of a surface layer, such

  7. Deciding between using the first or second drop of blood for the self monitoring of blood glucose.

    Science.gov (United States)

    Li, Min; Wang, Xiaoli; Shan, Zhongyan

    2014-12-01

    To explore whether the first or the second drop of blood is more suitable for the self-monitoring of blood glucose (SMBG). SMBG was employed in hospitalized patients using the first and second drop of blood. Venous blood glucose was measured meanwhile. The differences in blood glucose measurements were then compared in groups with different regions of blood glucose levels. There were 802 groups of blood glucose in 526 patients. There was no significant difference in the blood glucose levels of the first and second drop of blood and venous blood. However, after combining then dividing measurements into six groups according to blood glucose concentration, we found statistically significant differences between the blood glucose levels obtained from the first drop, second drop, and venous blood in the groups containing blood glucose values blood can be used for performing SMBG to assess real-time venous glucose. By categorizing blood glucose into different levels more accurately, we observed that there was no significant difference between the first or second drop of blood and the venous blood glucose value when blood glucose levels were maintained between 10 and 20 mmol/L. When blood glucose levels were below 10 mmol/L, the value obtained from first drop of blood was close to that from venous blood, whereas when the blood glucose level is >20 mmol/L, the blood glucose value from the second drop of blood was more accurate. Copyright © 2014 Primary Care Diabetes Europe. Published by Elsevier Ltd. All rights reserved.

  8. An evaporation model of multicomponent solution drops

    Science.gov (United States)

    Sartori, Silvana; Liñán, Amable; Lasheras, Juan C.

    2010-11-01

    Solutions of polymers are widely used in the pharmaceutical industry as tablets coatings. These allow controlling the rate at which the drug is delivered, taste or appearance. The coating is performed by spraying and drying the tablets at moderate temperatures. The wetting of the coating solution on the pill's surface depends on the droplet Webber and Re numbers, angle of impact and on the rheological properties of the droplet. We present a model for the evaporation of multicomponent solutions droplets in a hot air environment with temperatures substantially lower than the boiling temperature of the solvent. As the liquid vaporizes from the surface the fluid in the drop increases in concentration, until reaching its saturation point. After saturation, precipitation occurs uniformly within the drop. As the surface regresses, a compacting front formed by the precipitate at its maximum packing density advances into the drop, while the solute continues precipitating uniformly. This porous shell grows fast due to the double effect of surface regression and precipitation. The evaporation rate is determined by the rates at which heat is transported to the droplet surface and at which liquid vapor diffuses away from it. When the drop is fully compacted, the evaporation is drastically reduced.

  9. Spontaneous evaporation of the acetone drop

    Science.gov (United States)

    Dunin, S. Z.; Nagornov, O. V.

    2017-12-01

    The exact solution of the problem on evaporation of the acetone sessile drop at solid substrate is derived. The solution allows us to analyze the temperature field behavior at various thermodynamic parameters. The Marangoni forces are calculated in explicit form. The solution can be used to check numerical approaches for similar problems.

  10. Check valves with drop-shaped disk

    Energy Technology Data Exchange (ETDEWEB)

    1943-03-19

    This report discusses improvements possible with drop check valves. Up to the time of the report, the most important improvements had been: (1) lightening of the drop by hollowing it out, (2) reducing lift to reduce impact, (3) increasing clearance in the guide to minimize the danger of it getting stuck, (4) drilling of a safety hole which would indicate excessive wear of the housing by a leak. Other possibilities for the above improvements had produced the following conclusions: (1) a further lightening of the drop was found possible by milling out the halves with a milling cutter, by welding them together and thus eliminating the threaded portion, or by having the drop open on the bottom; (2) further reduction in lift was not found possible in most sizes, but for reduction of the impact effect by a cushion of oil or paste, the seating surface was widened as much as possible; (3) sticking of certain check valves caused by ferrous sulfide deposits could be solved by use of a certain bushing in the housing; (4) some plants favored and some disfavored the safety hole, but in general, plants were to service check valves and change them at such regular intervals as experience dictated; (5) the seat plate was no longer solid steel, but a welded piece.

  11. Goose droppings as food for reindeer

    NARCIS (Netherlands)

    van der Wal, R; Loonen, MJJE

    Feeding conditions for Svalbard reindeer, Rangifer tarandus platyrhynchus, on Spitsbergen are generally poor, owing to low availability of forage. We report on coprophagy: the use of goose faeces as an alternative food source for reindeer. Fresh droppings from Barnacle Geese, Branta leucopsis,

  12. Modeling merging behavior at lane drops.

    Science.gov (United States)

    2015-02-01

    In work-zone configurations where lane drops are present, merging of traffic at the taper presents an operational concern. In : addition, as flow through the work zone is reduced, the relative traffic safety of the work zone is also reduced. Improvin...

  13. 49 CFR 178.603 - Drop test.

    Science.gov (United States)

    2010-10-01

    ... of natural wood, Plywood boxes, Reconstituted wood boxes, Fiberboard boxes, Plastic boxes, Steel or... drums, Plastic drums and Jerricans, Composite packagings which are in the shape of a drum Six—(three for... Administrator. (c) Special preparation of test samples for the drop test. (1) Testing of plastic drums, plastic...

  14. 49 CFR 178.965 - Drop test.

    Science.gov (United States)

    2010-10-01

    ... Large Packaging design types and performed periodically as specified in § 178.955(e) of this subpart. (b... § 178.960(d). (d) Test method. (1) Samples of all Large Packaging design types must be dropped onto a... be restored to the upright position for observation. (2) Large Packaging design types with a capacity...

  15. The initial regime of drop coalescence

    Science.gov (United States)

    Anthony, Christopher; Harris, Michael; Basaran, Osman

    2017-11-01

    Drop coalescence plays a key role in both industry and nature. Consequently, study of the phenomenon has been the focus of numerous experimental, computational and theoretical works to date. In coalescence, two drops come into contact and a liquid bridge forms between them. As time advances, this bridge grows from microscopic to macroscopic scales. Despite the large volume of work dedicated to this problem, currently experiment, theory, and computation are not in perfect agreement with respect to the earliest times following the initial contact of the drops. Experiments report an initial regime where the radius of the connecting bridge grows linearly in time before a transition to either a Stokes regime or an inertial regime where either viscous or inertial forces balance capillary force. In the initial linear regime, referred to as the inertially-limited viscous regime, all three forces are thought to be important. This is in contrast to theory which predicts that all coalescence events begin in the Stokes regime. We use high accuracy numerical simulation to show that the existing discrepancy in the literature can be resolved by paying careful attention to the initial conditions that set the shape and size of the bridge connecting the two drops.

  16. The stability of cylindrical pendant drops

    CERN Document Server

    McCuan, John

    2018-01-01

    The author considers the stability of certain liquid drops in a gravity field satisfying a mixed boundary condition. He also considers as special cases portions of cylinders that model either the zero gravity case or soap films with the same kind of boundary behavior.

  17. Reactor Flow and Pressure Drop Study

    Energy Technology Data Exchange (ETDEWEB)

    Keyes, R. E.

    1969-07-15

    A study was made to determine the flow rates and pressure drops for all primary system flow paths through the FTR. The main data and results are in tables, diagrams and curves. The results are intended to provide a common basis for evaluation of parametric changes in the system.

  18. Biomechanical analysis of drop and countermovement jumps

    NARCIS (Netherlands)

    Bobbert, M. F.; Mackay, M.T.; Schinkelshoek, D.; Huijing, P. A.; van Ingen Schenau, G. J.

    For 13 subjects the performance of drop jumps from a height of 40 cm (DJ) and of countermovement jumps (CMJ) was analysed and compared. From force plate and cine data biomechanical variables including forces, moments, power output and amount of work done were calculated for hip, knee and ankle

  19. Scaling the drop size in coflow experiments

    International Nuclear Information System (INIS)

    Castro-Hernandez, E; Gordillo, J M; Gundabala, V; Fernandez-Nieves, A

    2009-01-01

    We perform extensive experiments with coflowing liquids in microfluidic devices and provide a closed expression for the drop size as a function of measurable parameters in the jetting regime that accounts for the experimental observations; this expression works irrespective of how the jets are produced, providing a powerful design tool for this type of experiments.

  20. Scaling the drop size in coflow experiments

    Energy Technology Data Exchange (ETDEWEB)

    Castro-Hernandez, E; Gordillo, J M [Area de Mecanica de Fluidos, Universidad de Sevilla, Avenida de los Descubrimientos s/n, 41092 Sevilla (Spain); Gundabala, V; Fernandez-Nieves, A [School of Physics, Georgia Institute of Technology, Atlanta, GA 30332 (United States)], E-mail: jgordill@us.es

    2009-07-15

    We perform extensive experiments with coflowing liquids in microfluidic devices and provide a closed expression for the drop size as a function of measurable parameters in the jetting regime that accounts for the experimental observations; this expression works irrespective of how the jets are produced, providing a powerful design tool for this type of experiments.

  1. [Preservative-containing eye drops and adherence in ophthalmological practice].

    Science.gov (United States)

    Lanzl, I; Kaercher, T

    2012-11-01

    Chronic eye diseases, such as glaucoma or dry eye syndrome, require long-term drug application to the eyes. Good adherence is required to achieve the therapeutic goal and patient needs and requirements have to be taken into account. This distinguishes adherence to drug therapy from the former compliance which implies only following medical instructions. Adherence is influenced by socioeconomic, health system-related, disease-related, treatment-related and patient-related factors. It can be measured by tedious procedures, such as electronic monitoring, self-assessment, drop counting and laboratory findings of systemic drug levels. Non-adherence is a growing medical problem worldwide. An increase in adherence means an increased degree of therapeutic safety for the patient and long-term cost savings for the individual as well as society. Non-adherence in chronic diseases, such as glaucoma and dry eye syndrome is increased by eye drops that cause side effects. Often these side effects are caused by agents such as the preservative benzalkonium chloride. To achieve a good adherence preservative-free eye drops are advised.

  2. Facilitators and Barriers of Drop-In Center Use Among Homeless Youth.

    Science.gov (United States)

    Pedersen, Eric R; Tucker, Joan S; Kovalchik, Stephanie A

    2016-08-01

    Drop-in centers for homeless youth address basic needs for food, hygiene, and clothing but can also provide critical services that address youth's "higher level" needs (e.g., substance use treatment, mental health care, HIV-related programs). Unlike other services that have restrictive rules, drop-in centers typically try to break down barriers and take a "come as you are" approach to engaging youth in services. Given their popularity, drop-in centers represent a promising location to deliver higher level services to youth that may not seek services elsewhere. A better understanding of the individual-level factors (e.g., characteristics of homeless youth) and agency-level factors (e.g., characteristics of staff and environment) that facilitate and impede youth engagement in drop-in centers will help inform research and outreach efforts designed to engage these at-risk youth in services. Thus, the goal of this review was to develop a preliminary conceptual model of drop-in center use by homeless youth. Toward this goal, we reviewed 20 available peer-reviewed articles and reports on the facilitators and barriers of drop-in center usage and consulted broader models of service utilization from both youth and adult studies to inform model development. Copyright © 2016 Society for Adolescent Health and Medicine. All rights reserved.

  3. Lifetime of oil drops pressed by buoyancy against a planar interface: Large drops

    Science.gov (United States)

    Rojas, Clara; García-Sucre, Máximo; Urbina-Villalba, Germán

    2010-11-01

    In a previous report [C. Rojas, G. Urbina-Villalba, and M. García-Sucre, Phys. Rev. E 81, 016302 (2010)10.1103/PhysRevE.81.016302] it was shown that emulsion stability simulations are able to reproduce the lifetime of micrometer-size drops of hexadecane pressed by buoyancy against a planar water-hexadecane interface. It was confirmed that small drops (ri<10μm) stabilized with β -casein behave as nondeformable particles, moving with a combination of Stokes and Taylor tensors as they approach the interface. Here, a similar methodology is used to parametrize the potential of interaction of drops of soybean oil stabilized with bovine serum albumin. The potential obtained is then employed to study the lifetime of deformable drops in the range 10≤ri≤1000μm . It is established that the average lifetime of these drops can be adequately replicated using the model of truncated spheres. However, the results depend sensibly on the expressions of the initial distance of deformation and the maximum film radius used in the calculations. The set of equations adequate for large drops is not satisfactory for medium-size drops (10≤ri≤100μm) , and vice versa. In the case of large particles, the increase in the interfacial area as a consequence of the deformation of the drops generates a very large repulsive barrier which opposes coalescence. Nevertheless, the buoyancy force prevails. As a consequence, it is the hydrodynamic tensor of the drops which determine the characteristic behavior of the lifetime as a function of the particle size. While the average values of the coalescence time of the drops can be justified by the mechanism of film thinning, the scattering of the experimental data of large drops cannot be rationalized using the methodology previously described. A possible explanation of this phenomenon required elaborate simulations which combine deformable drops, capillary waves, repulsive interaction forces, and a time-dependent surfactant adsorption.

  4. Pension Fund Governing Board

    CERN Multimedia

    HR Department

    2008-01-01

    Note The CERN pension scheme is based on the principle of defined benefits, so beneficiaries continue to receive the benefits to which they are entitled in accordance with the Rules of the Pension Fund. This means that pension entitlements under the Rules are not directly affected by the financial crisis and the current economic situation. However, the adjustment of pensions to the cost of living is not automatic and, under the method applied since 2006, must take into account the Fund’s financial position. Meeting of the Pension Fund Governing Board The Pension Fund Governing Board held its eighth meeting at ESO in Garching (near Munich), Germany on 24 October 2008. Before starting its work, the Governing Board had the privilege of hearing an opening address by Professor Tim de Zeeuw, the Director General of ESO. Professor de Zeeuw described the mission of ESO and the ambitious projects of his organisation, which performs astronomy observations using telescopes located in Chile. The Director-General receiv...

  5. 78 FR 16713 - Board Meeting; April 16, 2013; Richland, WA

    Science.gov (United States)

    2013-03-18

    ... performed by DOE's Office of Nuclear Energy on the potential for directly disposing of existing SNF storage... day will be on DOE's Strategy for the Management and Disposal of Used Nuclear Fuel and High-Level... NUCLEAR WASTE TECHNICAL REVIEW BOARD Board Meeting; April 16, 2013; Richland, WA The U.S. Nuclear...

  6. Independent School Leadership: Heads, Boards, and Strategic Thinking

    Science.gov (United States)

    Baker, Troy; Campbell, Stephen; Ostroff, David

    2016-01-01

    This study seeks to identify and assess factors that contribute to effective independent school governance at the board of trustees level. A review of extant literature reveals two major challenges: (a) definitions and standards of board effectiveness are inconsistent, and (b) there is very little empirical evidence to support existing definitions…

  7. Leading for Learning: Leadership Practices of Effective Boards

    Science.gov (United States)

    Johnson, Paul A.

    2010-01-01

    Do school boards have a role in student achievement? Recent research suggests that they do. This article identifies 12 board of education leadership practices associated with higher levels of student achievement: creating a vision, using data, setting goals, monitoring progress and taking corrective action, creating awareness and urgency, engaging…

  8. Assessment of the effect of board density and species on ...

    African Journals Online (AJOL)

    Homogenous cement-bonded flake-boards were made from exotic plantation hardwood species (Gmelina arborea and Leucaena leucocephala) and the combination of the two species at equal weight ratio. Flake-boards were produced from each of the raw materials at three density levels of 1000 kg/m3, 1100 kg/m3 and ...

  9. On the Internationalization of Corporate Boards

    DEFF Research Database (Denmark)

    Oxelheim, Lars; Gregoric, Aleksandra; Randøy, Trond

    2013-01-01

    This study investigates the internationalization of corporate boards, using a sample of 346 non-financial listed Nordic firms during 2001-2008. Given a high level of international activity, these firms have surprisingly few foreign directors. The picture of international expertise changes conside...... of the nationals covaries with foreign sales, and increases with the share of foreign directors. Thus both sources of international expertise should be considered when analyzing board internationalization....... considerably, however, if we also count the international experience of national directors. The percentage of foreign directors is related primarily to financial internationalization rather than foreign sales, and thus presumably to the monitoring rather than advisory functions. The international experience...

  10. Optical Multiplexer Board 6U Prototype

    CERN Document Server

    Valero, A; Castillo, V; Cuenca, C; Ferrer, A; Fullana, E; González, V; Higón, E; Poveda, J; Ruiz-Martinez, A; Saez, M; Salvachúa, B; Sanchis, E; Solans, C; Torres, J; Valls, J A

    2007-01-01

    This paper describes the technical specifications of the Optical Multiplexer Board (OMB) 6U prototype. First, the hardware characteristics of this board are detailed as well as a description of the circuits and the components used. Firmware developed to achieve the desired functionality is also described. The tests conducted with the OMB in the TileCal ROD production tasks are also explained. Finally, a preliminary description of the final Optical Multiplexer Board 9U design is included. This design which is currently going on has to work in the ATLAS final experiment at CERN. General specifications at hardware and firmware levels are detailed pointing out especially the differences between the first prototype already tested and the final version.

  11. Coalescence collision of liquid drops I: Off-center collisions of equal-size drops

    Directory of Open Access Journals (Sweden)

    Alejandro Acevedo-Malavé

    2011-09-01

    Full Text Available The Smoothed Particle Hydrodynamics method (SPH is used here to model off-center collisions of equal-size liquid drops in a three-dimensional space. In this study the Weber number is calculated for several conditions of the droplets dynamics and the velocity vector fields formed inside the drops during the collision process are shown. For the permanent coalescence the evolution of the kinetic and internal energy is shown and also the approaching to equilibrium of the resulting drop. Depending of the Weber number three possible outcomes for the collision of droplets is obtained: permanent coalescence, flocculation and fragmentation. The fragmentation phenomena are modeled and the formation of small satellite drops can be seen. The ligament that is formed follows the “end pinching” mechanism and it is transformed into a flat structure.

  12. Patients overwhelmingly prefer inpatient boarding to emergency department boarding.

    Science.gov (United States)

    Viccellio, Peter; Zito, Joseph A; Sayage, Valerie; Chohan, Jasmine; Garra, Gregory; Santora, Carolyn; Singer, Adam J

    2013-12-01

    Boarding of admitted patients in the emergency department (ED) is a major cause of crowding. One alternative to boarding in the ED, a full-capacity protocol where boarded patients are redeployed to inpatient units, can reduce crowding and improve overall flow. Our aim was to compare patient satisfaction with boarding in the ED vs. inpatient hallways. We performed a structured telephone survey regarding patient experiences and preferences for boarding among admitted ED patients who experienced boarding in the ED hallway and then were subsequently transferred to inpatient hallways. Demographic and clinical characteristics, as well as patient preferences, including items related to patient comfort and safety using a 5-point scale, were recorded and descriptive statistics were used to summarize the data. Of 110 patients contacted, 105 consented to participate. Mean age was 57 ± 16 years and 52% were female. All patients were initially boarded in the ED in a hallway before their transfer to an inpatient hallway bed. The overall preferred location after admission was the inpatient hallway in 85% (95% confidence interval 75-90) of respondents. In comparing ED vs. inpatient hallway boarding, the following percentages of respondents preferred inpatient boarding with regard to the following 8 items: rest, 85%; safety, 83%; confidentiality, 82%; treatment, 78%; comfort, 79%; quiet, 84%; staff availability, 84%; and privacy, 84%. For no item was there a preference for boarding in the ED. Patients overwhelmingly preferred the inpatient hallway rather than the ED hallway when admitted to the hospital. Copyright © 2013 Elsevier Inc. All rights reserved.

  13. Control of Drop Motion by Mechanical Vibrations

    Science.gov (United States)

    Bestehorn, Michael

    2014-11-01

    Since the first experimental observations of Michael Faraday in 1831 it is known that a vibrating liquid may show an instability of its flat free surface with respect to oscillating regular surface patterns. We study thin liquid films on a horizontal substrate in the long wave approximation. The films are parametrically excited by mechanical horizontal or inclined oscillations. Inertia effects are taken into account and the standard thin film formulation is extended by a second equation for the vertically averaged mass flux. The films can be additionally unstable by Van der Waals forces on a partially wetting substrate, leading to the formation of drops. These drops can be manipulated by the vibrations to move in a desired direction. Linear results based on a damped complex valued Mathieu equation as well as fully nonlinear results using a reduced model will be presented, for more details see.

  14. A pressure drop model for PWR grids

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Dong Seok; In, Wang Ki; Bang, Je Geon; Jung, Youn Ho; Chun, Tae Hyun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1998-12-31

    A pressure drop model for the PWR grids with and without mixing device is proposed at single phase based on the fluid mechanistic approach. Total pressure loss is expressed in additive way for form and frictional losses. The general friction factor correlations and form drag coefficients available in the open literatures are used to the model. As the results, the model shows better predictions than the existing ones for the non-mixing grids, and reasonable agreements with the available experimental data for mixing grids. Therefore it is concluded that the proposed model for pressure drop can provide sufficiently good approximation for grid optimization and design calculation in advanced grid development. 7 refs., 3 figs., 3 tabs. (Author)

  15. How drops start sliding over solid surfaces

    Science.gov (United States)

    Gao, Nan; Geyer, Florian; Pilat, Dominik W.; Wooh, Sanghyuk; Vollmer, Doris; Butt, Hans-Jürgen; Berger, Rüdiger

    2018-02-01

    It has been known for more than 200 years that the maximum static friction force between two solid surfaces is usually greater than the kinetic friction force--the force that is required to maintain the relative motion of the surfaces once the static force has been overcome. But the forces that impede the lateral motion of a drop of liquid on a solid surface are not as well characterized, and there is a lack of understanding about liquid-solid friction in general. Here, we report that the lateral adhesion force between a liquid drop and a solid can also be divided into a static and a kinetic regime. This striking analogy with solid-solid friction is a generic phenomenon that holds for liquids of different polarities and surface tensions on smooth, rough and structured surfaces.

  16. Drop evaporation and triple line dynamics

    Science.gov (United States)

    Sobac, Benjamin; Brutin, David; Gavillet, Jerome; Université de Provence Team; Cea Liten Team

    2011-03-01

    Sessile drop evaporation is a phenomenon commonly came across in nature or in industry with cooling, paintings or DNA mapping. However, the evaporation of a drop deposited on a substrate is not completely understood due to the complexity of the problem. Here we investigate, with several nano-coating of the substrate (PTFE, SiOx, SiOc and CF), the influence of the dynamic of the triple line on the evaporation process. The experiment consists in analyzing simultaneously the motion of the triple line, the kinetics of evaporation, the internal thermal motion and the heat and mass transfer. Measurements of temperature, heat-flux and visualizations with visible and infrared cameras are performed. The dynamics of the evaporative heat flux appears clearly different depending of the motion of the triple line

  17. Semisupervised Community Detection by Voltage Drops

    Directory of Open Access Journals (Sweden)

    Min Ji

    2016-01-01

    Full Text Available Many applications show that semisupervised community detection is one of the important topics and has attracted considerable attention in the study of complex network. In this paper, based on notion of voltage drops and discrete potential theory, a simple and fast semisupervised community detection algorithm is proposed. The label propagation through discrete potential transmission is accomplished by using voltage drops. The complexity of the proposal is OV+E for the sparse network with V vertices and E edges. The obtained voltage value of a vertex can be reflected clearly in the relationship between the vertex and community. The experimental results on four real networks and three benchmarks indicate that the proposed algorithm is effective and flexible. Furthermore, this algorithm is easily applied to graph-based machine learning methods.

  18. Numerical study on drop formation through a micro nozzle

    International Nuclear Information System (INIS)

    Kim, Sung Il; Son, Gi Hun

    2005-01-01

    The drop ejection process from a micro nozzle is investigated by numerically solving the conservation equations for mass and momentum. The liquid-gas interface is tracked by a level set method which is extended for two-fluid flows with irregular solid boundaries. Based on the numerical results, the liquid jet breaking and droplet formation behavior is found to depend strongly on the pulse type of forcing pressure and the contact angle at the gas-liquid-solid interline. The negative pressure forcing can be used to control the formation of satelite droplets. Also, various nozzle shapes are tested to investigate their effect on droplet formation

  19. Head-on collision of drops: A numerical investigation

    Science.gov (United States)

    Nobari, M. R.; Jan, Y.-J.; Tryggvason, G.

    1993-01-01

    The head-on collision of equal sized drops is studied by full numerical simulations. The Navier-Stokes equations are solved for fluid motion both inside and outside the drops using a front tracking/finite difference technique. The drops are accelerated toward each other by a body force that is turned off before the drops collide. When the drops collide, the fluid between them is pushed outward leaving a thin later bounded by the drop surface. This layer gets progressively thinner as the drops continue to deform and in several of the calculations this double layer is artificially removed once it is thin enough, thus modeling rupture. If no rupture takes place, the drops always rebound, but if the film is ruptured the drops may coalesce permanently or coalesce temporarily and then split again.

  20. Drag and Drop API v HTML5

    OpenAIRE

    BARABÁŠ, Vít

    2013-01-01

    The work (the bachelor´s thesis) deals with a new way of web application management via the "drag and drop" technique in the HTML5 programming language. The work is divided into two parts. The first part consists of DND API description in HTML5. The support analysis within common web browsers is included as a part of this description. The second, practical part of the thesis focuses on a concept and the following realisation of a photogallery using DND API.

  1. Sessile Drop Evaporation and Leidenfrost Phenomenon

    OpenAIRE

    A. K. Mozumder; M. R. Ullah; A. Hossain; M. A. Islam

    2010-01-01

    Problem statement: Quenching and cooling are important process in manufacturing industry for controlling the mechanical properties of materials, where evaporation is a vital mode of heat transfer. Approach: This study experimentally investigated the evaporation of sessile drop for four different heated surfaces of Aluminum, Brass, Copper and Mild steel with a combination of four different liquids as Methanol, Ethanol, Water and NaCl solution. The time of evaporation for the droplet on the hot...

  2. Superheated drop as a neutron spectrometer

    OpenAIRE

    Das, Mala; Chatterjee, B. K.; Roy, B.; Roy, S. C.

    2000-01-01

    Superheated drops are known to vaporise when exposed to energetic nuclear radiation since the discovery of bubble chamber. As the degree of superheat increases in a given liquid, less and less energetic neutrons are required to cause nucleation. This property of superheated liquids are being utilised to develope the neutron spectromer. A new principle of neutron spectrometry using Superheated liquid are developed and the developed principle has been tested by Am-Be neutron source.

  3. Low-Pressure-Drop Shutoff Valve

    Science.gov (United States)

    Thornborrow, John

    1994-01-01

    Flapper valve remains open under normal flow conditions but closes upon sudden increases to high rate of flow and remains closed until reset. Valve is fluid/mechanical analog of electrical fuse or circuit breaker. Low-pressure-drop shutoff valve contains flapper machined from cylindrical surface. During normal flow conditions, flapper presents small cross section to flow. (Useful in stopping loss of fluid through leaks in cooling systems.)

  4. Drops on hydrophobic surfaces & vibrated fluid surfaces

    DEFF Research Database (Denmark)

    Wind-Willassen, Øistein

    of a droplet is then given, after which we set up a 2D computational Finite-Element Method (FEM) model for a neutrally buoyant drop immersed in another liquid. The model is validated by considering the volume loss over time. Subsequent to an introduction to the physics of wetting, the developed FEM model......-leap dynamics, exotic trajectories and the emergence of statistical behavior when the forcing is near the Faraday threshold....

  5. The jet mass distribution after Soft Drop

    Science.gov (United States)

    Marzani, Simone; Schunk, Lais; Soyez, Gregory

    2018-02-01

    We present a first-principle computation of the mass distribution of jets which have undergone the grooming procedure known as Soft Drop. This calculation includes the resummation of the large logarithms of the jet mass over its transverse momentum, up to next-to-logarithmic accuracy, matched to exact fixed-order results at next-to-leading order. We also include non-perturbative corrections obtained from Monte-Carlo simulations and discuss analytic expressions for hadronisation and Underlying Event effects.

  6. 78 FR 1 - Soybean Promotion and Research: Amend the Order To Adjust Representation on the United Soybean Board

    Science.gov (United States)

    2013-01-02

    ...] Soybean Promotion and Research: Amend the Order To Adjust Representation on the United Soybean Board... number of members on the United Soybean Board (Board) to reflect changes in production levels that have occurred since the Board was reapportioned in 2009. As required by the Soybean Promotion, Research, and...

  7. Eye-Drops for Activation of DREADDs

    Directory of Open Access Journals (Sweden)

    William T. Keenan

    2017-11-01

    Full Text Available Designer Receptors Exclusively Activated by Designer Drugs (DREADDs are an important tool for modulating and understanding neural circuits. Depending on the DREADD system used, DREADD-targeted neurons can be activated or repressed in vivo following a dose of the DREADD agonist clozapine-N-oxide (CNO. Because DREADD experiments often involve behavioral assays, the method of CNO delivery is important. Currently, the most common delivery method is intraperitoneal (IP injection. IP injection is both a fast and reliable technique, but it is painful and stressful particularly when many injections are required. We sought an alternative CNO delivery paradigm, which would retain the speed and reliability of IP injections without being as invasive. Here, we show that CNO can be effectively delivered topically via eye-drops. Eye-drops robustly activated DREADD-expressing neurons in the brain and peripheral tissues and does so at the same dosages as IP injection. Eye-drops provide an easier, less invasive and less stressful method for activating DREADDs in vivo.

  8. Drop friction on liquid-infused surfaces

    Science.gov (United States)

    Gas, Armelle; Keiser, Ludovic; Clanet, Christophe; Quere, David

    2017-11-01

    Trapping a thin liquid film in the roughness of a textured material creates a surface that is partially solid and partially liquid, referred to as a lubricant-impregnated surface. Those surfaces have recently raised a great interest for their promising industrial applications. Indeed, they proved to drastically reduce adhesion of a broad range of liquids, leading to enhanced mobility, and strong anti-biofouling, anti-icing and anti-fogging properties. In our talk we discuss the nature of the friction generated as a drop glides on a textured material infused by another liquid. Different regimes are observed, depending on the viscosities of both liquids. While a viscous drop is simply opposed by a Stokes-type friction, the force opposing a drop moving on a viscous substrate becomes non-linear in velocity. A liquid on an infused material is surrounded by a meniscus, and this specific feature is proposed to be responsible for the special observed frictions, on both adhesive and nonadhesive substrates.

  9. Organization of microbeads in Leidenfrost drops.

    Science.gov (United States)

    Maquet, Laurent; Colinet, Pierre; Dorbolo, Stéphane

    2014-06-21

    We investigated the organization of micrometric hydrophilic beads (glass or basalt) immersed in Leidenfrost drops. Starting from a large volume of water compared to the volume of the beads, while the liquid evaporates, we observed that the grains are eventually trapped at the interface of the droplet and accumulate. At a moment, the grains entirely cover the droplet. We measured the surface area at this moment as a function of the total mass of particles inserted in the droplet. We concluded that the grains form a monolayer around the droplet assuming (i) that the packing of the beads at the surface is a random close packing and (ii) that the initial surface of the drop is larger than the maximum surface that the beads can cover. Regarding the evaporation dynamics, the beads are found to reduce the evaporation rate of the drop. The slowdown of the evaporation is interpreted as being the consequence of the dewetting of the particles located at the droplet interface which makes the effective surface of evaporation smaller. As a matter of fact, contact angles of the beads with the water deduced from the evaporation rates are consistent with contact angles of beads directly measured at a flat air-water interface of water in a container.

  10. Ultrasonic characterization of single drops of liquids

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, D.N.

    1998-04-14

    Ultrasonic characterization of single drops of liquids is disclosed. The present invention includes the use of two closely spaced transducers, or one transducer and a closely spaced reflector plate, to form an interferometer suitable for ultrasonic characterization of droplet-size and smaller samples without the need for a container. The droplet is held between the interferometer elements, whose distance apart may be adjusted, by surface tension. The surfaces of the interferometer elements may be readily cleansed by a stream of solvent followed by purified air when it is desired to change samples. A single drop of liquid is sufficient for high-quality measurement. Examples of samples which may be investigated using the apparatus and method of the present invention include biological specimens (tear drops; blood and other body fluid samples; samples from tumors, tissues, and organs; secretions from tissues and organs; snake and bee venom, etc.) for diagnostic evaluation, samples in forensic investigations, and detection of drugs in small quantities. 5 figs.

  11. Practical neutron dosimetry with superheated drops.

    Science.gov (United States)

    Apfel, R E; Lo, Y C

    1989-01-01

    The Superheated Drop Detector (SDD) is a new kind of neutron detector based on the same principle as that of the bubble chamber, except the superheated material is in drop form suspended by a gel or polymer as first described by Apfel (U.S. Patent 4,143,274). Previously, we have developed a theoretical model for the prediction of the threshold neutron energy to nucleate bubbles in our superheated materials and a model for the calculation of the energy dependent response function of SDD. The results of the theoretical calculations agree with the experimental measurements reasonably well. We found the measured response curve of one of our SDDs follows the same trend as the ideal ICRP dose equivalent response curve within 40% for neutrons of energy above 100 keV and within a factor of 10 below 100 keV. Therefore, it is possible to make a rem-response Superheated Drop Detector. We have further calibrated our SDD with 252Cf neutron sources (both bare and D2O moderated). The results are in reasonable agreement with our theoretical predictions, which proves that our model is valid not only for monoenergetic neutrons but also for neutrons from a radioactive source. The principles of operation of our detector, which can be used in neutron dosimetry, area monitoring, and neutron spectrometry, are discussed.

  12. Evaluation of the impact behavior of the contents of reprocessing radioactive waste shipping cask subjected to drop impact

    International Nuclear Information System (INIS)

    Shirai, K.; Ito, C.; Funahashi, M.

    1993-01-01

    In this study, to investigate the impact response characteristics of the contents in the cask precisely, we performed the laboratory-scale drop tests, and on the basis of the test results, we proposed the construction of the spring-mass model and confirmed the accuracy of the proposed drop analysis method by comparison with drop test using a full-scale cask for high level wastes. Following the results of the drop tests and analysis, the outline of the contents and results is summarized below. 1) The drop tests onto the unyielding surface using a scale model containing several contents were performed and the effect of the interaction between the contents and the cask body on the impact response experimentally. 2) The above interaction can be characterized by the gap between the contents and the cask body caused by the release of the gravitational force at the moment the drop started. So, we proposed the analysis method for considering gap using spring-mass model by comparing the laboratory-scale drop test results. 3) We applied the proposed analysis method to a drop test using a full-scale cask for high level wastes, and it was found that this method seems to be good and convenient enough to evaluate the impact behavior of the contents in a transport cask subjected to drop impact. (J.P.N.)

  13. Reference Architecture for High Dependability On-Board Computers

    Science.gov (United States)

    Silva, Nuno; Esper, Alexandre; Zandin, Johan; Barbosa, Ricardo; Monteleone, Claudio

    2014-08-01

    The industrial process in the area of on-board computers is characterized by small production series of on- board computers (hardware and software) configuration items with little recurrence at unit or set level (e.g. computer equipment unit, set of interconnected redundant units). These small production series result into a reduced amount of statistical data related to dependability, which influence on the way on-board computers are specified, designed and verified. In the context of ESA harmonization policy for the deployment of enhanced and homogeneous industrial processes in the area of avionics embedded systems and on-board computers for the space industry, this study aimed at rationalizing the initiation phase of the development or procurement of on-board computers and at improving dependability assurance. This aim was achieved by establishing generic requirements for the procurement or development of on-board computers with a focus on well-defined reliability, availability, and maintainability requirements, as well as a generic methodology for planning, predicting and assessing the dependability of on- board computers hardware and software throughout their life cycle. It also provides guidelines for producing evidence material and arguments to support dependability assurance of on-board computers hardware and software throughout the complete lifecycle, including an assessment of feasibility aspects of the dependability assurance process and how the use of computer-aided environment can contribute to the on-board computer dependability assurance.

  14. DOE's Environmental Management Site-Specific Advisory Board: The Roles, Work, and Assessment of the Constituent Local Boards - 13587

    International Nuclear Information System (INIS)

    Alexander, Catherine; Freeman, Jenny; Cantrell, Yvette

    2013-01-01

    The charter for the Department of Energy's Environmental Management (EM) Site-Specific Advisory Board (SSAB) was approved under the Federal Advisory Committee Act (FACA) in 1994. With a unique mandate to provide public input on issues associated with the cleanup of nuclear legacy sites in the U.S., the EM SSAB comprises eight local boards, which are based at major EM sites. While each board is unique to the community in which it is located and reflects the diversity of the local population, the boards are governed by FACA, related regulations, and DOE policies that are intended to standardize agency advisory board operations. The EM SSAB local boards are made up of a diverse group of citizens who want to understand the mission and goals of the EM program and to help EM achieve those goals for the benefit of their communities. Some are quite passionate about their mission; others need to be coaxed into active participation. Maintaining productive relationships and a supportive environment for effective board operations is the challenge of board management for DOE EM and the board members themselves. DOE draws on research findings and best practices literature from academics and practitioners in the field of public involvement in its board management practices. The EM SSAB is also evaluated annually under the law to ensure that the investment of taxpayer dollars in the board is warranted in light of the contributions of the board. Further evaluation takes place at the agency and site levels in order to identify what aspects of board functioning the agency and board members find important to its success and to address areas where improvement is needed. Board contributions, compliance factors, and measurable outcomes related to board products and process areas are key to agency commitment to ongoing support of the boards and to participant satisfaction and thus continued member involvement. In addition to evaluation of these factors in improving board effectiveness

  15. What makes great boards great.

    Science.gov (United States)

    Sonnenfeld, Jeffrey A

    2002-09-01

    In the wake of meltdowns at WorldCom, Tyco, and Enron, enormous attention has been focused on the companies' boards. It seems inconceivable that business disasters of such magnitude could happen without gross or even criminal negligence on the part of board members. And yet a close examination of those boards reveals no broad pattern of incompetence or corruption. In fact, they followed most of the accepted standards for board operations: Members showed up for meetings; they had money invested in the company; audit committees, compensation committees, and codes of ethics were in place; the boards weren't too small or too big, nor were they dominated by insiders. In other words, they passed the tests that would normally be applied to determine whether a board of directors was likely to do a good job. And that's precisely what's so scary, according to corporate governance expert Jeffrey Sonnenfeld, who suggests that it's time for some new thinking about how corporate boards operate and are evaluated. He proposes thinking not only about how to structure the board's work but also about how to manage it as a social system. Good boards are, very simply, high-functioning work groups. They're distinguished by a climate of respect, trust, and candor among board members and between the board and management. Information is shared openly and on time; emergent political factions are quickly eliminated. Members feel free to challenge one another's assumptions and conclusions, and management encourages lively discussion of strategic issues. Directors feel a responsibility to contribute meaningfully to the board's performance. In addition, good boards assess their own performance, both collectively and individually.

  16. Laplacian drop shapes and effect of random perturbations on accuracy of surface tension measurement for different drop constellations.

    Science.gov (United States)

    Saad, Sameh M I; Neumann, A Wilhelm

    2015-08-01

    Theoretical drop shapes are calculated for three drop constellations: pendant drops, constrained sessile drops, and unconstrained sessile drops. Based on total Gaussian curvature, shape parameter and critical shape parameter are discussed as a function of different drop sizes and surface tensions. The shape parameter is linked to physical parameters for every drop constellation. The as yet unavailable detailed dimensional analysis for the unconstrained sessile drop is presented. Results show that the unconstrained sessile drop shape depends on a dimensionless volume term and the contact angle. Random perturbations are introduced and the accuracy of surface tension measurement is assessed for precise and perturbed profiles of the three drop constellations. It is concluded that pendant drops are the best method for accurate surface tension measurement, followed by constrained sessile drops. The unconstrained sessile drops come last because they tend to be more spherical at low and moderate contact angles. Of course, unconstrained sessile drops are the only option if contact angles are to be measured. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Tethered Satellite System Contingency Investigation Board

    Science.gov (United States)

    1992-11-01

    The Tethered Satellite System (TSS-1) was launched aboard the Space Shuttle Atlantis (STS-46) on July 31, 1992. During the attempted on-orbit operations, the Tethered Satellite System failed to deploy successfully beyond 256 meters. The satellite was retrieved successfully and was returned on August 6, 1992. The National Aeronautics and Space Administration (NASA) Associate Administrator for Space Flight formed the Tethered Satellite System (TSS-1) Contingency Investigation Board on August 12, 1992. The TSS-1 Contingency Investigation Board was asked to review the anomalies which occurred, to determine the probable cause, and to recommend corrective measures to prevent recurrence. The board was supported by the TSS Systems Working group as identified in MSFC-TSS-11-90, 'Tethered Satellite System (TSS) Contingency Plan'. The board identified five anomalies for investigation: initial failure to retract the U2 umbilical; initial failure to flyaway; unplanned tether deployment stop at 179 meters; unplanned tether deployment stop at 256 meters; and failure to move tether in either direction at 224 meters. Initial observations of the returned flight hardware revealed evidence of mechanical interference by a bolt with the level wind mechanism travel as well as a helical shaped wrap of tether which indicated that the tether had been unwound from the reel beyond the travel by the level wind mechanism. Examination of the detailed mission events from flight data and mission logs related to the initial failure to flyaway and the failure to move in either direction at 224 meters, together with known preflight concerns regarding slack tether, focused the assessment of these anomalies on the upper tether control mechanism. After the second meeting, the board requested the working group to complete and validate a detailed integrated mission sequence to focus the fault tree analysis on a stuck U2 umbilical, level wind mechanical interference, and slack tether in upper tether

  18. First AGU Board of Directors

    Science.gov (United States)

    McPhaden, Michael J.

    2010-08-01

    On 1 July 2010, the first AGU Board of Directors took office. The board is composed of the president, president-elect, immediate past president, general secretary, international secretary, development board chair, six members elected by the Union membership, vice chair of the AGU Council, and the executive director. Two additional members may be nominated by the AGU president and approved by the board. The creation of the board is a result of the new governance structure approved by the AGU membership in November 2009. The board is responsible for the business aspects of the Union, while an expanded AGU Council will focus on science issues. Council members will be introduced in a future issue of Eos.

  19. Prospective, randomized, controlled comparison of SYSTANE UD eye drops versus VISINE INTENSIV 1% EDO eye drops for the treatment of moderate dry eye.

    Science.gov (United States)

    Jacobi, Christina; Kruse, Friedrich E; Cursiefen, Claus

    2012-12-01

    The aim of this prospective, randomized, clinical, single-center study was to compare the safety and efficacy of 2 ocular surface lubricant eye drops: preservative-free hydroxypropyl (HP)-Guar (SYSTANE UD(®)) eye drops versus preservative-free Tamarindus indica seed polysaccharide (TSP) 1% (VISINE INTENSIV 1% EDO(®)) eye drops. Fifty-six eyes of 28 patients with moderate keratoconjunctivitis sicca (DEWS severity level 2) were enrolled in the trial. Patients were randomized for 2 treatment groups (SYSTANE UD eye drops vs. VISINE INTENSIV 1% EDO eye drops). The eye drops in both groups were applied 5 times per day for 3 months. Statistical analyses were performed using Statistica™ software (Mann-Whitney U-test and Wilcoxon test). P-Values<0.05 were considered significant. After 3 months of treatment the patients of both groups had subjective benefit in the relief of symptoms of dry eye disease evaluated by the Ocular Surface Disease Index (OSDI) questionnaire score. Patients treated with HP-Guar and TSP showed improvements in tear film stability measured by tear break-up time (TBUT), which are statistically significant in the HP-Guar group (P=0.02). The results of this clinical trial show improvements of symptoms and signs in patients with moderate dry eye after the consistent use of preservative-free HP-Guar and TSP lubricant eye drops. Both artificial tear formulations produce amelioration in tear film stability improving eye conditions and patient quality of life. HP-Guar seems to be slightly more effective in improving ocular surface protection by decreasing tear film evaporation.

  20. Currency Boards; The Ultimate Fix?

    OpenAIRE

    Atish R. Ghosh

    1998-01-01

    The growing integration of world capital markets has made it fashionable to argue that only extreme exchange rate regimes are sustainable. Short of adopting a common currency, currency board arrangements represent the most extreme form of exchange rate peg. This paper compares the macroeconomic performance of countries with currency boards to those with other forms of pegged exchange rate regime. Currency boards are indeed associated with better inflation performance, even allowing for potent...

  1. Drying drops : Drying drops containing solutes: From hydrodynamical to mechanical instabilities.

    Science.gov (United States)

    Giorgiutti-Dauphiné, F; Pauchard, L

    2018-03-19

    The drying of complex fluids involves a large number of microscopic phenomena (transport and organization of non-volatile solutes) as well as hydrodynamic and mechanical instabilities. These phenomena can be captured in drying sessile drops where different domains can be identified: strong concentration gradients, formation of a glassy or porous envelope that withstands mechanical stress, and consolidation of a layer strongly adhering to the substrate at the drop edge. In colloidal systems, we quantify the evolution of the particle volume fraction at a nanometric scale and microscopic scale and identify the conditions for the envelope formation at the free surface by balancing the effect of diffusion and evaporation. When a solid envelope is formed at a drop surface, the mechanical instabilities induced by the drying result in different drop shapes. Finally, large drying stresses build up in the solid layer adhering on the substrate, and possibly cause crack formation. In particular, we study how crack patterns are affected by the contact angle of drops and the drying conditions. A particular interest of the review is devoted to drying pattern of solutes.

  2. Advocacy for Early Language Education: A School Board Presentation.

    Science.gov (United States)

    Gramer, Virginia

    1999-01-01

    Presents a school board presentation on the benefits of early foreign language learning. The presentation included success stories of students who began learning foreign languages at the elementary level. (Author/VWL)

  3. Simplified procedure for determining of drop and stilling basin

    Directory of Open Access Journals (Sweden)

    Ali R. Vatankhah

    2014-03-01

    Full Text Available Drops are used to effectively dissipate the surplus energy of the water flow. A closed conduit drop conveys water and stills it at its downstream. I-type pipe drop is one kind of the closed conduit drops which is used in irrigation networks as a typical hydraulic structure. Sump elevation is an important design parameter for I-type pipe drop. Similarly, in supercritical flow structures, such as open channel chutes, determination of stilling basin invert elevation is very important. At present, these key design parameters are determined by the momentum and energy equations using tedious trial-and-error procedure. In this study, square conduit drop, pipe drop, and rectangular stilling basin are considered, and three explicit equations have been developed by (multiple nonlinear regression technique to determine the sump and stilling basin invert elevations. Being very simple and accurate, these equations can be easily used to design the closed conduit drops and stilling basins by hydraulic engineers.

  4. Low magnesium level

    Science.gov (United States)

    Low magnesium level is a condition in which the amount of magnesium in the blood is lower than normal. The medical ... that convert or use energy ( metabolism ). When the level of magnesium in the body drops below normal, ...

  5. Static Board evaluation on Go

    OpenAIRE

    STRIHAGEN,, KARL; HEDENCRONA, DANIEL

    2014-01-01

    Computers are still not outperforming professional go-players because of several complex aspects of the game. A common feature of computerised board-game players is that they needs a estimated value of how good or bad a given board is for one of the players. In this report we evaluate some trivial board-evaluation algorithms for the go board in how accurate they are to the outcome of the whole go-match.To our disappointment but also not unexpected very simple heuristic methods don't show any ...

  6. German versus Nordic Board Models

    DEFF Research Database (Denmark)

    Ringe, Georg

    2016-01-01

    changes and developments in business practice, the article argues that board practices in the two systems effectively blur the structural distinction, and that board organization is converging in practice. It thereby contributes to the broader debates on functionality and comparative corporate law......Board structure is an important component of the individual governance of firms, and the appropriateness of the various models is one of the most debated issues in corporate governance today. A comparison of the Nordic and German approaches to the structure of corporate boards reveals stark...

  7. Modular Integrated Stackable Layers (MISL) MI_MSP430A Board Design Document (BDD)

    Science.gov (United States)

    Yim, Hester

    2013-01-01

    This is a board-level design document for Modular Integrated Stackable Layers (MISL) MI_MSP430A board (PIN MSP430F5438A). The Board Design Document (BDD) contains the description, features of microcontroller, electrical and mechanical design, and drawings.

  8. Partial coalescence from bubbles to drops

    KAUST Repository

    Zhang, F. H.

    2015-10-07

    The coalescence of drops is a fundamental process in the coarsening of emulsions. However, counter-intuitively, this coalescence process can produce a satellite, approximately half the size of the original drop, which is detrimental to the overall coarsening. This also occurs during the coalescence of bubbles, while the resulting satellite is much smaller, approximately 10 %. To understand this difference, we have conducted a set of coalescence experiments using xenon bubbles inside a pressure chamber, where we can continuously raise the pressure from 1 up to 85 atm and thereby vary the density ratio between the inner and outer fluid, from 0.005 up to unity. Using high-speed video imaging, we observe a continuous increase in satellite size as the inner density is varied from the bubble to emulsion-droplet conditions, with the most rapid changes occurring as the bubble density grows up to 15 % of that of the surrounding liquid. We propose a model that successfully relates the satellite size to the capillary wave mode responsible for its pinch-off and the overall deformations from the drainage. The wavelength of the primary wave changes during its travel to the apex, with the instantaneous speed adjusting to the local wavelength. By estimating the travel time of this wave mode on the bubble surface, we also show that the model is consistent with the experiments. This wavenumber is determined by both the global drainage as well as the interface shapes during the rapid coalescence in the neck connecting the two drops or bubbles. The rate of drainage is shown to scale with the density of the inner fluid. Empirically, we find that the pinch-off occurs when 60 % of the bubble fluid has drained from it. Numerical simulations using the volume-of-fluid method with dynamic adaptive grid refinement can reproduce these dynamics, as well as show the associated vortical structure and stirring of the coalescing fluid masses. Enhanced stirring is observed for cases with second

  9. Delayed Frost Growth on Jumping-Drop Superhydrophobic Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Boreyko, Jonathan B [ORNL; Collier, Pat [ORNL

    2013-01-01

    Self-propelled jumping drops are continuously removed from a condensing superhydrophobic surface to enable a micrometric steady-state drop size. Here, we report that subcooled condensate on a chilled superhydrophobic surface are able to repeatedly jump off the surface before heterogeneous ice nucleation occurs. Frost still forms on the superhydrophobic surface due to ice nucleation at neighboring edge defects, which eventually spreads over the entire surface via an inter-drop frost wave. The growth of this inter-drop frost front is shown to be up to three times slower on the superhydrophobic surface compared to a control hydrophobic surface, due to the jumping-drop effect dynamically minimizing the average drop size and surface coverage of the condensate. A simple scaling model is developed to relate the success and speed of inter-drop ice bridging to the drop size distribution. While other reports of condensation frosting on superhydrophobic surfaces have focused exclusively on liquid-solid ice nucleation for isolated drops, these findings reveal that the growth of frost is an inter-drop phenomenon that is strongly coupled to the wettability and drop size distribution of the surface. A jumping-drop superhydrophobic condenser was found to be superior to a conventional dropwise condenser in two respects: preventing heterogeneous ice nucleation by continuously removing subcooled condensate, and delaying frost growth by minimizing the success of interdrop ice bridge formation.

  10. Preparation and Stability of Voriconazole Eye Drop Solution▿

    OpenAIRE

    Dupuis, Antoine; Tournier, Nicolas; Le Moal, Gwenaël; Venisse, Nicolas

    2008-01-01

    The combined systemic and topical administration of voriconazole has successfully been used to treat keratomycosis. Because no voriconazole eye drop product is commercially available, we prepared a sterile eye drop solution (10 mg/ml). Voriconazole remains stable over 30 days, providing an eye drop solution suitable for use for the topical treatment of fungal keratitis.

  11. Spent Nuclear Fuel (SNF) Bounding Drop Support Calculations

    Energy Technology Data Exchange (ETDEWEB)

    CHENAULT, D.M.

    1999-11-16

    This report evaluates different drop heights, concrete and other impact media to which the transport package and/or the MCO is dropped. A prediction method is derived for estimating the resultant impact factor for determining the bounding drop case for the SNF Project.

  12. Inverse Leidenfrost Effect: Levitating Drops on Liquid Nitrogen.

    Science.gov (United States)

    Adda-Bedia, M; Kumar, S; Lechenault, F; Moulinet, S; Schillaci, M; Vella, D

    2016-05-03

    We explore the interaction between a liquid drop (initially at room temperature) and a bath of liquid nitrogen. In this scenario, heat transfer occurs through film-boiling: a nitrogen vapor layer develops that may cause the drop to levitate at the bath surface. We report the phenomenology of this inverse Leidenfrost effect, investigating the effect of the drop size and density by using an aqueous solution of a tungsten salt to vary the drop density. We find that (depending on its size and density) a drop either levitates or instantaneously sinks into the bulk nitrogen. We begin by measuring the duration of the levitation as a function of the radius R and density ρd of the liquid drop. We find that the levitation time increases roughly linearly with drop radius but depends weakly on the drop density. However, for sufficiently large drops, R ≥ Rc(ρd), the drop sinks instantaneously; levitation does not occur. This sinking of a (relatively) hot droplet induces film-boiling, releasing a stream of vapor bubbles for a well-defined length of time. We study the duration of this immersed-drop bubbling finding similar scalings (but with different prefactors) to the levitating drop case. With these observations, we study the physical factors limiting the levitation and immersed-film-boiling times, proposing a simple model that explains the scalings observed for the duration of these phenomena, as well as the boundary of (R,ρd) parameter space that separates them.

  13. Dynamics of the vapor layer below a Leidenfrost drop.

    Science.gov (United States)

    Caswell, Thomas A

    2014-07-01

    In the Leidenfrost effect a small drop of fluid is levitated, above a sufficiently hot surface, on a persistent vapor layer generated by evaporation from the drop. The vapor layer thermally insulates the drop from the surface leading to extraordinarily long drop lifetimes. The top-view shape of the levitated drops can exhibit persistent starlike vibrations. I extend recent work [Burton et al., Phys. Rev. Lett. 109, 074301 (2012)] to study the bottom surface of the drop using interference imaging. In this work I use a high-speed camera and automated image analysis to image, locate, and classify the interference fringes. From the interference fringes I reconstruct the shape and height profile of the rim where the drop is closest to the surface. I measure the drop-size dependence of the planar vibrational mode frequencies, which agree well with previous work. I observe a distinct breathing mode in the average radius of the drop, the frequency of which scales differently with drop size than the other modes. This breathing mode can be tightly coupled to a vertical motion of the drop. I further observe a qualitative difference in the structure and dynamics of the vertical profile of the rim between large and small drops.

  14. The evaporation of the charged and uncharged water drops ...

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    Oscillations of the drop and the change in airflow around drops are suggested to contribute to lowering of the ventilation coefficients for charged drops. Applicability of the results to a small fraction of highly charged raindrops falling through the sub-cloud layer below thunderstorm is discussed. The relaxation time required for ...

  15. Spent Nuclear Fuel (SNF) Bounding Drop Support Calculations

    International Nuclear Information System (INIS)

    CHENAULT, D.M.

    1999-01-01

    This report evaluates different drop heights, concrete and other impact media to which the transport package and/or the MCO is dropped. A prediction method is derived for estimating the resultant impact factor for determining the bounding drop case for the SNF Project

  16. Pension Fund governing board

    CERN Multimedia

    HR Department

    2008-01-01

    On 16 March and 7 May, the Pension Fund Governing Board (PFGB) held its fourth and fifth meetings The first of these meetings was primarily dedicated to the examination of the strategic asset allocation. The PFGB reaffirmed the main goal of the new strategic asset allocation: to improve the Pension Fund’s position with regard to risk by lowering overall portfolio volatility through suitable investments in less volatile asset classes such as real estate and absolute return strategies, where the return does not depend on market trends and negative growth is extremely unlikely. The finalised document will be presented to the Finance Committee and the Council at their June meetings for approval, in accordance with the provisions of the Levaux report. The PFGB also took note of the Internal Audit’s report on Pension Fund operations and decided to refer it to Working Group I as a working document for establishing a control and internal monitoring system for Pension Fund oper...

  17. The board demography – firm performance relationship revisited: opening the ‘black box’ using Bayesian analysis

    OpenAIRE

    Huybrechts, Jolien; Voordeckers, Wim; D'Espallier, Bert; Lybaert, Nadine; Vandemaele, Sigrid; Van Gils, Anita

    2011-01-01

    Boards of directors have enjoyed an increased attention in recent management research. Because of scant and conflicting empirical evidence on the relationships between board demographic variables and firm performance, recent research has shown special interest for the antecedents of board performance in an effort to open the black box of the board of directors. We build on this research by testing a model that incorporates not only these board-level outcomes but also includes the preceding bo...

  18. Non-wetting drops at liquid interfaces: from liquid marbles to Leidenfrost drops

    Science.gov (United States)

    Wong, Clint Y. H.; Adda-Bedia, Mokhtar; Vella, Dominic

    We consider the flotation of deformable, non-wetting drops on a liquid interface. We consider the deflection of both the liquid interface and the droplet itself in response to the buoyancy forces, density difference and the various surface tensions within the system. Our results suggest new insight into a range of phenomena in which such drops occur, including Leidenfrost droplets and floating liquid marbles. In particular, we show that the floating state of liquid marbles is very sensitive to the tension of the particle-covered interface and suggest that this sensitivity may make such experiments a useful assay of the properties of these complex interfaces.

  19. Dynamic response characteristics analysis of the doubly-fed wind power system under grid voltage drop

    Science.gov (United States)

    Chen, Y.; Wang, J.; Wang, H. H.; Yang, L.; Chen, W.; Xu, Y. T.

    2016-08-01

    Double-fed induction generator (DFIG) is sensitive to the disturbances of grid, so the security and stability of the grid and the DFIG itself are under threat with the rapid increase of DFIG. Therefore, it is important to study dynamic response of the DFIG when voltage drop failure is happened in power system. In this paper, firstly, mathematical models and the control strategy about mechanical and electrical response processes is respectively introduced. Then through the analysis of response process, it is concluded that the dynamic response characteristics are related to voltage drop level, operating status of DFIG and control strategy adapted to rotor side. Last, the correctness of conclusion is validated by the simulation about mechanical and electrical response processes in different voltage levels drop and different DFIG output levels under DIgSILENT/PowerFactory software platform.

  20. A Case-Control Study on the Oxidative Balance of 50% Autologous Serum Eye Drops

    Directory of Open Access Journals (Sweden)

    Patrícia Ioschpe Gus

    2016-01-01

    Full Text Available Importance. Autologous serum (AS eye drops are recommended for severe dry eye in patients with ocular surface disease. No description of the antioxidant balance of AS eye drops has been reported in the literature. Objective. This study sought to evaluate the total reactive antioxidant potential (TRAP and concentration of reactive oxygen species (ROS in samples of 50% AS eye drops and their correlations with the demographic characteristics and lifestyle habits of patients with ocular surface disease and healthy controls. Design. This was a case-control study with a 3-month follow-up period. Participants. 16 patients with severe dry eye disease of different etiologies and 17 healthy controls matched by age, gender, and race were included. Results. TRAP and ROS were detected at all evaluated times. There were no differences in the mean ROS (p=0.429 or TRAP (p=0.475 levels between cases and controls. No statistically significant differences in the concentrations of ROS or TRAPs were found at 0, 15, or 30 days (p for ROS = 0.087 and p for TRAP = 0.93. Neither the demographic characteristics nor the lifestyle habits were correlated with the oxidative balance of the 50% AS eye drops. Conclusions and Relevance. Both fresh and frozen 50% AS eye drops present antioxidant capacities and ROS in an apparently stable balance. Moreover, patients with ocular surface disease and normal controls produce equivalent AS eye drops in terms of oxidative properties.

  1. Model of an Evaporating Drop Experiment

    Science.gov (United States)

    Rodriguez, Nicolas

    2017-11-01

    A computational model of an experimental procedure to measure vapor distributions surrounding sessile drops is developed to evaluate the uncertainty in the experimental results. Methanol, which is expected to have predominantly diffusive vapor transport, is chosen as a validation test for our model. The experimental process first uses a Fourier transform infrared spectrometer to measure the absorbance along lines passing through the vapor cloud. Since the measurement contains some errors, our model allows adding random noises to the computational integrated absorbance to mimic this. Then the resulting data are interpolated before passing through a computed tomography routine to generate the vapor distribution. Next, the gradients of the vapor distribution are computed along a given control volume surrounding the drop so that the diffusive flux can be evaluated as the net rate of diffusion out of the control volume. Our model of methanol evaporation shows that the accumulated errors of the whole experimental procedure affect the diffusive fluxes at different control volumes and are sensitive to how the noisy data of integrated absorbance are interpolated. This indicates the importance of investigating a variety of data fitting methods to choose which is best to present the data. Trinity University Mach Fellowship.

  2. Vlasov simulations of parallel potential drops

    Directory of Open Access Journals (Sweden)

    H. Gunell

    2013-07-01

    Full Text Available An auroral flux tube is modelled from the magnetospheric equator to the ionosphere using Vlasov simulations. Starting from an initial state, the evolution of the plasma on the flux tube is followed in time. It is found that when applying a voltage between the ends of the flux tube, about two thirds of the potential drop is concentrated in a thin double layer at approximately one Earth radius altitude. The remaining part is situated in an extended region 1–2 Earth radii above the double layer. Waves on the ion timescale develop above the double layer, and they move toward higher altitude at approximately the ion acoustic speed. These waves are seen both in the electric field and as perturbations of the ion and electron distributions, indicative of an instability. Electrons of magnetospheric origin become trapped between the magnetic mirror and the double layer during its formation. At low altitude, waves on electron timescales appear and are seen to be non-uniformly distributed in space. The temporal evolution of the potential profile and the total voltage affect the double layer altitude, which decreases with an increasing field aligned potential drop. A current–voltage relationship is found by running several simulations with different voltages over the system, and it agrees with the Knight relation reasonably well.

  3. Visualization of the impact of water drops on a hot surface: effect of drop velocity and surface inclination

    Energy Technology Data Exchange (ETDEWEB)

    Celata, Gian Piero; Mariani, Andrea; Zummo, Giuseppe [ENEA, Institute of Thermal-Fluid Dynamics, S. Maria di Galeria (Rome) (Italy); Cumo, Maurizio [Universita di Roma ' ' La Sapienza' ' , Rome (Italy)

    2006-08-15

    The behaviour of one drop impinging on a hot surface by varying the surface temperature, the drop velocity and the position of the surface (horizontal and a inclined 45 ) both at a temperature below and above the Leidenfrost temperature has been experimentally evaluated, estimating the temperature at which the drop rebounds. A large influence on the drop velocity has been evidenced. The inclination of the surface decreases the critical value of the temperature above which the surface is not rewetted. (orig.)

  4. Vortex-induced buckling of a viscous drop impacting a pool

    KAUST Repository

    Li, Erqiang

    2017-07-20

    We study the intricate buckling patterns which can form when a viscous drop impacts a much lower viscosity miscible pool. The drop enters the pool by its impact inertia, flattens, and sinks by its own weight while stretching into a hemispheric bowl. Upward motion along the outer bottom surface of this bowl produces a vortical boundary layer which separates along its top and rolls up into a vortex ring. The vorticity is therefore produced in a fundamentally different way than for a drop impacting a pool of the same liquid. The vortex ring subsequently advects into the bowl, thereby stretching the drop liquid into ever thinner sheets, reaching the micron level. The rotating motion around the vortex pulls in folds to form multiple windings of double-walled toroidal viscous sheets. The axisymmetric velocity field thereby stretches the drop liquid into progressively finer sheets, which are susceptible to both axial and azimuthal compression-induced buckling. The azimuthal buckling of the sheets tends to occur on the inner side of the vortex ring, while their folds can be stretched and straightened on the outside edge. We characterize the total stretching from high-speed video imaging and use particle image velocimetry to track the formation and evolution of the vortex ring. The total interfacial area between the drop and the pool liquid can grow over 40-fold during the first 50 ms after impact. Increasing pool viscosity shows entrapment of a large bubble on top of the drop, while lowering the drop viscosity produces intricate buckled shapes, appearing at the earliest stage and being promoted by the crater motions. We also present an image collage of the most intriguing and convoluted structures observed. Finally, a simple point-vortex model reproduces some features from the experiments and shows variable stretching along the wrapping sheets.

  5. Single board system for fuzzy inference

    Science.gov (United States)

    Symon, James R.; Watanabe, Hiroyuki

    1991-01-01

    The very large scale integration (VLSI) implementation of a fuzzy logic inference mechanism allows the use of rule-based control and decision making in demanding real-time applications. Researchers designed a full custom VLSI inference engine. The chip was fabricated using CMOS technology. The chip consists of 688,000 transistors of which 476,000 are used for RAM memory. The fuzzy logic inference engine board system incorporates the custom designed integrated circuit into a standard VMEbus environment. The Fuzzy Logic system uses Transistor-Transistor Logic (TTL) parts to provide the interface between the Fuzzy chip and a standard, double height VMEbus backplane, allowing the chip to perform application process control through the VMEbus host. High level C language functions hide details of the hardware system interface from the applications level programmer. The first version of the board was installed on a robot at Oak Ridge National Laboratory in January of 1990.

  6. Governance, sustainability and contemporary boards

    OpenAIRE

    Coulson-Thomas, Colin

    2016-01-01

    In relation to governance, sustainability and contemporary boards explores the changing business context, stakeholder relationships, the role of independent directors, remuneration and other committees, corporate purpose, and widening board perspectives in order to reconcile different perspectives and address sustainability concerns. Raises questions in these areas and in relation to determining what to sustain, reviewing contemporary approaches and understanding their consequences, relevance...

  7. Does Board Diversity Really Matter?

    DEFF Research Database (Denmark)

    Rose, Caspar; Munch-Madsen, Peter; Funch, Maja

    2013-01-01

    We study the impact of female board representation as well as citizenship on corporate performance based on a sample of the largest listed firms in the Nordic countries as well as Germany. We also seek to determine the variation of board structures using factor analysis. We find no support for an...

  8. General purpose programmable accelerator board

    Science.gov (United States)

    Robertson, Perry J.; Witzke, Edward L.

    2001-01-01

    A general purpose accelerator board and acceleration method comprising use of: one or more programmable logic devices; a plurality of memory blocks; bus interface for communicating data between the memory blocks and devices external to the board; and dynamic programming capabilities for providing logic to the programmable logic device to be executed on data in the memory blocks.

  9. Deformed liquid marbles: Freezing drop oscillations with powders

    KAUST Repository

    Marston, Jeremy

    2012-09-01

    In this work we show that when a liquid drop impacts onto a fine-grained hydrophobic powder, the final form of the drop can be very different from the spherical form with which it impacts. In all cases, the drop rebounds due to the hydrophobic nature of the powder. However, we find that above a critical impact speed, the drop undergoes a permanent deformation to a highly non-spherical shape with a near-complete coverage of powder, which then freezes the drop oscillations during rebound. © 2012 Elsevier B.V.

  10. The Dutch Female Board Index 2010

    NARCIS (Netherlands)

    Lückerath – Rovers, M.

    2010-01-01

    The Dutch Female Board Index 2010 shows for the fourth year a survey of female representation on the Executive Boards and Supervisory Boards of 99 Dutch NVs listed on Euronext Amsterdam. The companies were classified by the percentage of women in their joint Executive Board and Supervisory Board.

  11. Investigation of Concrete Floor Vibration Using Heel-Drop Test

    Science.gov (United States)

    Azaman, N. A. Mohd; Ghafar, N. H. Abd; Azhar, A. F.; Fauzi, A. A.; Ismail, H. A.; Syed Idrus, S. S.; Mokhjar, S. S.; Hamid, F. F. Abd

    2018-04-01

    In recent years, there is an increased in floor vibration problems of structures like residential and commercial building. Vibration is defined as a serviceability issue related to the comfort of the occupant or damage equipment. Human activities are the main source of vibration in the building and it could affect the human comfort and annoyance of residents in the building when the vibration exceed the recommend level. A new building, Madrasah Tahfiz located at Yong Peng have vibration problem when load subjected on the first floor of the building. However, the limitation of vibration occurs on building is unknown. Therefore, testing is needed to determine the vibration behaviour (frequency, damping ratio and mode shape) of the building. Heel-drop with pace 2Hz was used in field measurement to obtain the vibration response. Since, the heel-drop test results would vary in light of person performance, test are carried out three time to reduce uncertainty. Natural frequency from Frequency Response Function analysis (FRF) is 17.4Hz, 16.8, 17.4Hz respectively for each test.

  12. [Foot drop: an iatrogenic complication of spinal anesthesia].

    Science.gov (United States)

    Goyal, Vipin Kumar; Mathur, Vijay

    2018-01-16

    Foot drop in postoperative period is very rare after spinal anesthesia. Early clinical assessment and diagnostic interventions is of prime importance to establish the etiology and to start appropriate management. Close follow-up is warranted in early postoperative period in cases when patient complain paresthesia or pain during needle insertion or drug injection. A 22-year-old male was undergone lower limb orthopedic surgery in spinal anesthesia. During shifting from postoperative ward footdrop was suspected during routine assessment of regression of spinal level. Immediately the patient was referred to a neurologist and magnetic resonance imaging was done, which was inconclusive. Conservative management was started and nerve conduction study was done on the 4th postoperative day that confirmed pure motor neuropathy of right peroneal nerve. Patient was discharged with ankle splint and physiotherapy after slight improvement in motor power (2/5). Foot drop is very rare after spinal anesthesia. Any suspected patient must undergo emergent neurological consultation and magnetic resonance imaging to exclude major finding and need for early surgical intervention. Copyright © 2017 Sociedade Brasileira de Anestesiologia. Publicado por Elsevier Editora Ltda. All rights reserved.

  13. Optical Detection and Magnetic Manipulation of Drops in Microfluidic Devices

    Science.gov (United States)

    Kerbage, Charles

    2005-03-01

    We demonstrate an integrated magneto-optic microfluidic device for drop detection and sorting. Optical detection of water drops formed in a continuous oil phase flow is performed using optical fibers which are integrated into the channels of the PDMS (Polydimethylsiloxane) based microfluidic device. The size and the velocity of the drops can be determined by measuring the transmission intensity as a function of time. We also show that such a device can be used to detect fluorescent materials introduced in the drop itself. Moreover, introducing nano-scale magnetic particles into the water drops allows for drop sorting by means of a magnetic field gradient. This magnetic field is generated through thin film permalloy integrated into the device itself and tuned by an external coil. We show that the sorting depends on the magnetic field gradient, material composite and volume fraction of the magnetic material in the drops.

  14. Jumps, somersaults, and symmetry breaking in Leidenfrost drops

    Science.gov (United States)

    Chen, Simeng; Bertola, Volfango

    2016-08-01

    When a droplet of water impacts a heated surface, the drop may be observed to bounce. Recently is has been found that small quantities (˜100 ppm) of polymer additives such as polyethylene oxide can significantly increase the maximum bouncing height of drops. This effect has been explained in terms of the reduction of energy dissipation caused by polymer additives during the drop retraction and rebound, resulting in higher mechanical energy available for bouncing. Here we demonstrate, by comparing three types of fluids (Newtonian, shear-thinning, and viscoelastic), that the total kinetic energy carried by low-viscosity Newtonian drops during retraction is partly transformed into rotational kinetic energy rather than dissipated when compared with high-viscosity or non-Newtonian drops. We also show that non-Newtonian effects play little role in the energy distribution during drop impact, while the main effect is due to the symmetry break observed during the retraction of low-viscosity drops.

  15. Remote sensing the susceptibility of cloud albedo to changes in drop concentration

    International Nuclear Information System (INIS)

    Platnick, S.E.

    1991-01-01

    The role of clouds in reflecting solar radiation to space and thereby reducing surface heating is of critical importance to climate. Combustion processes that produce greenhouse gases also increase cloud condensation nuclei (CCN) concentrations which in turn increase cloud drop concentrations and thereby cloud albedo. A calculation of cloud susceptibility, defined in this work as the increase in albedo resulting from the addition of one cloud drop per cubic centimeter (as cloud liquid water content remains constant), is made through satellite remote sensing of cloud drop radius and optical thickness. The remote technique uses spectral channels of the Advanced Very High Resolution Radiometer (AVHRR) instrument on board the NOAA polar orbiting satellites. Radiative transfer calculations of reflectance and effective surface and cloud emissivities are made for applicable sun and satellite viewing angles, including azimuth, at various radii and optical thicknesses for each AVHRR channel. Emission in channel 3 (at 3.75 microns) is removed to give the reflected solar component. These calculations are used to infer the radius and optical thickness giving the best match to the satellite measurements. The effect of the atmosphere on the signal received by the satellite is included in the analysis

  16. Drop Pinch-Off for Discrete Flows from a Capillary

    Directory of Open Access Journals (Sweden)

    Wilson M.C.T.

    2013-07-01

    Full Text Available The problem of drop formation and pinch-off from a capillary tube under the influence of gravity has been extensively studied when the internal capillary pressure gradient is constant. This ensures a continuous time independent flow field inside the capillary tube typically of the Poiseuille flow type. Characteristic drop ejection behaviour includes: periodic drop ejection, drop ejection with associated satellite production, complex dripping, chaotic behaviour and jetting. It is well known that this characteristic behaviour is governed by the Weber (We and Ohnesorge (Oh numbers (for a given Bond number and may be delineated in a We verses Oh operability diagram. An in-depth physical understanding of drop ejection is also of great importance to industry where the tight control of drop size and ejection velocity are of critical importance in industrial processes such as sealants used in electronics assembly and inkjet printing. However, the use of such a continuous flow approach for drop ejection in industry is often impractical since such flows cannot be operator controlled. For this reason it is important to investigate so-called discrete pipe flows where the flow can be turned on and off at will. This means the flow inside the pipe is now time-dependent being controlled in a step-wise fashion. As a first stage in the investigation of drop pinch-off behaviour in discrete pipe flows this paper will study the critical pinch-off time required for drop ejection starting from a pendant drop. This is the discrete amount of time the pipe flow is turned on for in order for a drop to be ejected from the capillary. A Newtonian incompressible free-surface CFD flow code developed at the University of Leeds is used to investigate the critical pinch-off time for a range of internal pipe velocities (the central flow maximum in Poiseuille flow. It is found that the time required for drop ejection to occur decreases exponentially with internal pipe velocity

  17. Drop splashing is independent of substrate wetting

    Science.gov (United States)

    Latka, Andrzej; Boelens, Arnout M. P.; Nagel, Sidney R.; de Pablo, Juan J.

    2018-02-01

    A liquid drop impacting a dry solid surface with sufficient kinetic energy will splash, breaking apart into numerous secondary droplets. This phenomenon shows many similarities to forced wetting, including the entrainment of air at the contact line. Because of these similarities and the fact that forced wetting has been shown to depend on the wetting properties of the surface, existing theories predict splashing to depend on wetting properties as well. However, using high-speed interference imaging, we observe that at high capillary numbers wetting properties have no effect on splashing for various liquid-surface combinations. Additionally, by fully resolving the Navier-Stokes equations at length and time scales inaccessible to experiments, we find that the shape and motion of the air-liquid interface at the contact line/edge of the droplet are independent of wettability. We use these findings to evaluate existing theories and to compare splashing with forced wetting.

  18. Crack formation and prevention in colloidal drops

    Science.gov (United States)

    Kim, Jin Young; Cho, Kun; Ryu, Seul-A.; Kim, So Youn; Weon, Byung Mook

    2015-08-01

    Crack formation is a frequent result of residual stress release from colloidal films made by the evaporation of colloidal droplets containing nanoparticles. Crack prevention is a significant task in industrial applications such as painting and inkjet printing with colloidal nanoparticles. Here, we illustrate how colloidal drops evaporate and how crack generation is dependent on the particle size and initial volume fraction, through direct visualization of the individual colloids with confocal laser microscopy. To prevent crack formation, we suggest use of a versatile method to control the colloid-polymer interactions by mixing a nonadsorbing polymer with the colloidal suspension, which is known to drive gelation of the particles with short-range attraction. Gelation-driven crack prevention is a feasible and simple method to obtain crack-free, uniform coatings through drying-mediated assembly of colloidal nanoparticles.

  19. Drop Impact on a Solid Surface

    KAUST Repository

    Josserand, C.

    2015-09-22

    © Copyright 2016 by Annual Reviews. All rights reserved. A drop hitting a solid surface can deposit, bounce, or splash. Splashing arises from the breakup of a fine liquid sheet that is ejected radially along the substrate. Bouncing and deposition depend crucially on the wetting properties of the substrate. In this review, we focus on recent experimental and theoretical studies, which aim at unraveling the underlying physics, characterized by the delicate interplay of not only liquid inertia, viscosity, and surface tension, but also the surrounding gas. The gas cushions the initial contact; it is entrapped in a central microbubble on the substrate; and it promotes the so-called corona splash, by lifting the lamella away from the solid. Particular attention is paid to the influence of surface roughness, natural or engineered to enhance repellency, relevant in many applications.

  20. Drop Impact on to Moving Liquid Pools

    Science.gov (United States)

    Muñoz-Sánchez, Beatriz Natividad; Castrejón-Pita, José Rafael; Castrejón-Pita, Alfonso Arturo; Hutchings, Ian M.

    2014-11-01

    The deposition of droplets on to moving liquid substrates is an omnipresent situation both in nature and industry. A diverse spectrum of phenomena emerges from this simple process. In this work we present a parametric experimental study that discerns the dynamics of the impact in terms of the physical properties of the fluid and the relative velocity between the impacting drop and the moving liquid pool. The behaviour ranges from smooth coalescence (characterized by little mixing) to violent splashing (generation of multiple satellite droplets and interfacial vorticity). In addition, transitional regimes such as bouncing and surfing are also found. We classify the system dynamics and show a parametric diagram for the conditions of each regime. This work was supported by the EPSRC (Grant EP/H018913/1), the Royal Society, Becas Santander Universidades and the International Relationships Office of the University of Extremadura.

  1. Shape oscillations of a viscoelastic drop

    International Nuclear Information System (INIS)

    Khismatullin, Damir B.; Nadim, Ali

    2001-01-01

    Small-amplitude axisymmetric shape deformations of a viscoelastic liquid drop in microgravity are theoretically analyzed. Using the Jeffreys constitutive equation for linear viscoelasticity, the characteristic equation for the frequency and decay factor of the shape oscillations is derived. Asymptotic analysis of this equation is performed in the low- and high-viscosity limits and for the cases of small, moderate, and large elasticities. Elastic effects are shown to give rise to a type of shape oscillation that does not depend on the surface tension. The existence of such oscillations is confirmed by numerical solution of the characteristic equation in various regimes. A method for determining the viscoelastic properties of highly viscous liquids based upon experimental measurements of the frequency and damping rate of such shape oscillations is suggested

  2. Horizontal Drop of 21- PWR Waste Package

    International Nuclear Information System (INIS)

    A.K. Scheider

    2001-01-01

    The objective of this calculation is to determine the structural response of the waste package (WP) dropped horizontally from a specified height. The WP used for that purpose is the 21-Pressurized Water Reactor (PWR) WP. The scope of this document is limited to reporting the calculation results in terms of stress intensities. The information provided by the sketches (Attachment I) is that of the potential design of the type of WP considered in this calculation, and all obtained results are valid for that design only. This calculation is associated with the WP design and was performed by the Waste Package Design group in accordance with the ''Technical Work Plan for: Waste Package Design Description for LA'' (Ref. 16). AP-3.12Q, ''Calculations'' (Ref. 11) is used to perform the calculation and develop the document. The sketches attached to this calculation provide the potential dimensions and materials for the 21-PWR WP design

  3. Drop Out or Self-Exclusion? An Analysis of drop out causes in Mexico’s Sonoran High School Students

    Directory of Open Access Journals (Sweden)

    Elba Abril Valdez

    2008-05-01

    Full Text Available The scholar drop out is not an individual decision. It is conditioned by contextual factors which are identified and analyzed in this research paper among high school students. A survey was applied to 147 high school students to know their family situation, scholar history, reasons why they drop out and their future plans, among other relevant reasons. The results indicated that 86% of the surveyed students abandoned the school between the first and the third semester. Their grade average during the last semester studied was 7.49. The main reasons of the desertion of these students were: economic factors, failure in some subjects, and the lack of interest in their studies. 93% of the participants were not satisfied with the academic level they reached. Nonetheless, they did not plan to resume their studies. The results demonstrated the necessity of an intervention model based on educational policies with higher incentives to add to the school system, flexibility of the transit among subsystems and restructuration of the communication network among the principal actors.

  4. 7 CFR 1221.2 - Board.

    Science.gov (United States)

    2010-01-01

    ... ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE SORGHUM PROMOTION, RESEARCH, AND INFORMATION ORDER Sorghum Promotion, Research, and Information Order Definitions § 1221.2 Board. Board or Sorghum Promotion, Research, and Information Board means the administrative body established pursuant to...

  5. 78 FR 54629 - Consumer Advisory Board meeting

    Science.gov (United States)

    2013-09-05

    ... From the Federal Register Online via the Government Publishing Office CONSUMER FINANCIAL PROTECTION BUREAU Consumer Advisory Board meeting AGENCY: Bureau of Consumer Financial Protection. ACTION... Consumer Advisory Board (``CAB'' or ``Board'') of the Consumer Financial Protection Bureau (Bureau). The...

  6. 78 FR 66384 - Membership of the Merit Systems Protection Board's Performance Review Board

    Science.gov (United States)

    2013-11-05

    ... MERIT SYSTEMS PROTECTION BOARD Membership of the Merit Systems Protection Board's Performance Review Board AGENCY: Merit Systems Protection Board. ACTION: Notice. SUMMARY: Notice is hereby given of the members of the Merit Systems Protection Board's Performance Review Board. DATES: November 5, 2013...

  7. Establishing Trailer Ventilation (Boarding) Requirements for Finishing Pigs during Transport.

    Science.gov (United States)

    McGlone, John; Sapkota, Avi; Johnson, Anna; Kephart, Rebecca

    2014-08-19

    Specifically, this study aimed to establish the effects on mortality and morbidity of boarding levels (amount of side-wall trailer ventilation) for finishing pigs in mild weather (8.80 ± 0.30 °C, 71.70% ± 1.12% humidity). Pigs from commercial finishing sites were transported in 302 pot-bellied trailers to commercial processing plants. Measures collected at the processing plant were rates of dead on arrival (DOA), non-ambulatory, non-injured (NANI), non-ambulatory, injured (NAI), and total dead and down (D&D). Boarding levels (% that side walls were closed off with inserted boards) were divided into 3 bins: low, medium, and high, and outside temperature was divided into 4 bins 15 °C. Average rates of DOA, NANI, NAI, and D&D were approximately 0.30%, 0.12%, 0.04%, and 0.46%, respectively. The D&D was highest when boarding level was low with temperatures boarding level (medium and high boarding) in the temperature range of 5.10 °C to 23.30 °C did not affect pig losses.

  8. Sound Wave Energy Resulting from the Impact of Water Drops on the Soil Surface.

    Directory of Open Access Journals (Sweden)

    Magdalena Ryżak

    Full Text Available The splashing of water drops on a soil surface is the first step of water erosion. There have been many investigations into splashing-most are based on recording and analysing images taken with high-speed cameras, or measuring the mass of the soil moved by splashing. Here, we present a new aspect of the splash phenomenon's characterization the measurement of the sound pressure level and the sound energy of the wave that propagates in the air. The measurements were carried out for 10 consecutive water drop impacts on the soil surface. Three soils were tested (Endogleyic Umbrisol, Fluvic Endogleyic Cambisol and Haplic Chernozem with four initial moisture levels (pressure heads: 0.1 kPa, 1 kPa, 3.16 kPa and 16 kPa. We found that the values of the sound pressure and sound wave energy were dependent on the particle size distribution of the soil, less dependent on the initial pressure head, and practically the same for subsequent water drops (from the first to the tenth drop. The highest sound pressure level (and the greatest variability was for Endogleyic Umbrisol, which had the highest sand fraction content. The sound pressure for this soil increased from 29 dB to 42 dB with the next incidence of drops falling on the sample The smallest (and the lowest variability was for Fluvic Endogleyic Cambisol which had the highest clay fraction. For all experiments the sound pressure level ranged from ~27 to ~42 dB and the energy emitted in the form of sound waves was within the range of 0.14 μJ to 5.26 μJ. This was from 0.03 to 1.07% of the energy of the incident drops.

  9. Sound Wave Energy Resulting from the Impact of Water Drops on the Soil Surface.

    Science.gov (United States)

    Ryżak, Magdalena; Bieganowski, Andrzej; Korbiel, Tomasz

    2016-01-01

    The splashing of water drops on a soil surface is the first step of water erosion. There have been many investigations into splashing-most are based on recording and analysing images taken with high-speed cameras, or measuring the mass of the soil moved by splashing. Here, we present a new aspect of the splash phenomenon's characterization the measurement of the sound pressure level and the sound energy of the wave that propagates in the air. The measurements were carried out for 10 consecutive water drop impacts on the soil surface. Three soils were tested (Endogleyic Umbrisol, Fluvic Endogleyic Cambisol and Haplic Chernozem) with four initial moisture levels (pressure heads: 0.1 kPa, 1 kPa, 3.16 kPa and 16 kPa). We found that the values of the sound pressure and sound wave energy were dependent on the particle size distribution of the soil, less dependent on the initial pressure head, and practically the same for subsequent water drops (from the first to the tenth drop). The highest sound pressure level (and the greatest variability) was for Endogleyic Umbrisol, which had the highest sand fraction content. The sound pressure for this soil increased from 29 dB to 42 dB with the next incidence of drops falling on the sample The smallest (and the lowest variability) was for Fluvic Endogleyic Cambisol which had the highest clay fraction. For all experiments the sound pressure level ranged from ~27 to ~42 dB and the energy emitted in the form of sound waves was within the range of 0.14 μJ to 5.26 μJ. This was from 0.03 to 1.07% of the energy of the incident drops.

  10. Ownership Structure, Board Composition and Investment Performance

    OpenAIRE

    Eklund, Johan; Palmberg, Johanna; Wiberg, Daniel

    2009-01-01

    In this paper the relation between ownership structure, board composition and firm performance is explored. A panel of Swedish listed firms is used to investigate how board composition affects firm performance. Board heterogeneity is measured as board size, age and gender diversity. The results show that Swedish board of directors have become more diversified in terms of gender. Also, fewer firms have the CEO on the board which can be interpreted as a sign of increased independency. The regre...

  11. Marangoni Flow Induced Evaporation Enhancement on Binary Sessile Drops.

    Science.gov (United States)

    Chen, Pin; Harmand, Souad; Ouenzerfi, Safouene; Schiffler, Jesse

    2017-06-15

    The evaporation processes of pure water, pure 1-butanol, and 5% 1-butanol aqueous solution drops on heated hydrophobic substrates are investigated to determine the effect of temperature on the drop evaporation behavior. The evolution of the parameters (contact angle, diameter, and volume) during evaporation measured using a drop shape analyzer and the infrared thermal mapping of the drop surface recorded by an infrared camera were used in investigating the evaporation process. The pure 1-butanol drop does not show any thermal instability at different substrate temperatures, while the convection cells created by the thermal Marangoni effect appear on the surface of the pure water drop from 50 °C. Because 1-butanol and water have different surface tensions, the infrared video of the 5% 1-butanol aqueous solution drop shows that the convection cells are generated by the solutal Marangoni effect at any substrate temperature. Furthermore, when the substrate temperature exceeds 50 °C, coexistence of the thermal and solutal Marangoni flows is observed. By analyzing the relation between the ratio of the evaporation rate of pure water and 1-butanol aqueous solution drops and the Marangoni number, a series of empirical equations for predicting the evaporation rates of pure water and 1-butanol aqueous solution drops at the initial time as well as the equations for the evaporation rate of 1-butanol aqueous solution drop before the depletion of alcohol are derived. The results of these equations correspond fairly well to the experimental data.

  12. Pressure drop of He II flow through a porous media

    Science.gov (United States)

    Maddocks, J. R.; van Sciver, S. W.

    The paper reports on measurements of He II pressure drop across two porous SiO2 ceramic filter materials. These materials vary only in porosity, having values of 0.94 and 0.96. The average fiber diameter in both cases is approximately 5 microns. The experiment consists of a glass tube containing a piece of this sponge in one end. The tube is rapidly displaced downward in a bath of helium and the liquid levels are allowed to equilibrate over time producing variable velocities up to 10 cm/sec. The results are compared with those previously obtained using fine mesh screens. Good qualitative agreement is observed for turbulent flow; however, the behavior in the laminar flow regime is not fully understood.

  13. Investigating The Self-Esteem of Elemantary Boarding Scholls' Students

    OpenAIRE

    SEÇER, İsmail; İLBAY, Azmi; AY, İsmail; ÇİFTÇİ, Muhammet

    2013-01-01

    In this study, the second-tier regional boarding primary schools, students are receiving education and self-esteem levels of age, gender, type of study, academic achievement and significant differences according to the variables  whether or not to take disciplinary action were investigated. 2010-2011 academic research in the regional boarding primary schools are receiving education in Erzurum, which was carried out on 428 students. Piers and Harris to collect data from the study (1964), devel...

  14. The Atomic Safety and Licensing Board Panel

    International Nuclear Information System (INIS)

    1998-01-01

    Through the Atomic Energy Act, Congress made is possible for the public to get a full and fair hearing on civilian nuclear matters. Individuals who are directly affected by any licensing action involving a facility producing or utilizing nuclear materials may participate in a formal hearing, on the record, before independent judges on the Atomic Safety and Licensing Board Panel (ASLBP or Panel). Frequently, in deciding whether a license, permit, amendment, or extension should be granted to a particular applicant, the Panel members must be more than mere umpires. If appropriate, they are authorized to go beyond the issues the parties place before them in order to identify, explore, and resolve significant questions involving threats to the public health and safety that come to a board's attention during the proceedings. This brochure explains the purpose of the panel. Also addressed are: type of hearing handled; method of public participation; formality of hearings; high-level waste; other panel responsibilities and litigation technology

  15. Institutional directors and board compensation: Spanish evidence

    Directory of Open Access Journals (Sweden)

    Felix López-Iturriaga

    2015-07-01

    Full Text Available We address the influence of directors who represent institutional investors in three aspects of board compensation policies: level of compensation, composition, and performance sensitivity. We differentiate pressure-sensitive directors (i.e., with business links and pressure-resistant directors (i.e., without business links. Our results show that pressure-resistant directors decrease total board compensation and its fixed proportion, whereas they increase the variable proportion of total remuneration and the pay-for-performance sensitivity. By contrast, pressure-sensitive directors offer the opposite results. These findings are consistent with the view that institutional investors are not a homogeneous group and that pressure-resistant directors fulfill a more thorough monitoring role.

  16. IMPACT ANALYSIS OF SPENT FUEL DRY CASKS UNDER ACCIDENTAL DROP SCENARIOS

    International Nuclear Information System (INIS)

    BRAVERMAN, J.I.; MORANTE, R.J.; XU, J.; HOFMAYER, C.H.; SHAUKAT, S.K.

    2003-01-01

    A series of analyses were performed to assess the structural response of spent nuclear fuel dry casks subjected to various handling and on-site transfer events. The results of these analyses are being used by the Nuclear Regulatory Commission (NRC) to perform a probabilistic risk assessment (PRA). Although the PRA study is being performed for a specific nuclear plant, the PRA study is also intended to provide a framework for a general methodology that could also be applied to other dry cask systems at other nuclear plants. The dry cask system consists of a transfer cask, used for handling and moving the multi-purpose canister OLIIpC that contains the fuel, and a storage cask, used to store the MPC and fuel on a concrete pad at the site. This paper describes the analyses of the casks for two loading events. The first loading consists of dropping the transfer cask while it is lowered by a crane to a concrete floor at ground elevation. The second loading consists of dropping the storage cask while it is being transferred to the concrete storage pad outdoors. Three dimensional finite element models of the transfer cask and storage cask, containing the MPC and fuel, were utilized to perform the drop analyses. These models were combined with finite element models of the target structures being impacted. The transfer cask drop analyses considered various drop heights for the cask impacting the reinforced concrete floor at ground level. The finite element model of the target included a section of the concrete floor and concrete wall supporting the floor. The storage cask drop analyses evaluated a 30.5 cm (12 in.) drop of the cask impacting three different surfaces: reinforced concrete, asphalt, and gravel

  17. Drop Test Results of CRDM under Seismic Loads

    International Nuclear Information System (INIS)

    Choi, Myoung-Hwan; Cho, Yeong-Garp; Kim, Gyeong-Ho; Sun, Jong-Oh; Huh, Hyung

    2016-01-01

    This paper describes the test results to demonstrate the drop performance of CRDM under seismic loads. The top-mounted CRDM driven by the stepping motor for Jordan Research and Training Reactor (JRTR) has been developed in KAERI. The CRDM for JRTR has been optimized by the design improvement based on that of the HANARO. It is necessary to verify the drop performance under seismic loads such as operating basis earthquake (OBE) and safe shutdown earthquake (SSE). Especially, the CAR drop times are important data for the safety analysis. confirm the drop performance under seismic loads. The delay of drop time at Rig no. 2 due to seismic loads is greater than that at Rig no. 3. The total pure drop times under seismic loads are estimated as 1.169 and 1.855, respectively

  18. The Influence of Concentrace Mineral Drops on Performance Broiler

    Directory of Open Access Journals (Sweden)

    Sigit Mugiyono

    1999-05-01

    Full Text Available A research has been conducted in Experimental Farm Faculty of Animal Husbandry Unsoed from July 1 st until August 15 th, 1996. The purpose want to study the influence of CMD supplementation in drinking water consists of M0 = control; M1 = 0.5 drops/1000 cc, M2 = 1 drops/1000 cc; M3 = 1.5 drops/1000 cc and M4 = 2 drops/1000cc. The performance observed were growth, body weight, feed consumption, feed conversion, drinking water consumption; and income over feed and mineral cost (IOFMC. The research involved 100 broiler chickens divided that CMD supplementation until 2 drops/1000cc did not significantly affect on the performance of broiler chickens except in income over feed and mineral cost (P<0.05. (Animal Production 1(2: 56-62 (1999 Key Words: broiler, concentrace mineral drops, performance.

  19. A study of fungi on droppings of certain birds

    Directory of Open Access Journals (Sweden)

    C. S. Singh

    2014-08-01

    Full Text Available Droppings of fowl, owl, parrot, pigeon and sparrow were asepticaly collected in sterilized bottles from different places at Gorakhpur, 54 fungi were isolated. The number of fungi was more in the pigeon showing considerable decrease in the fowl and the sparrow. In the parrot and the owl, however. the fungi were egual in number. The number of Phycomycetes was almost the same on droppings of all birds, from parrot only one species could be isolated. A larger number of Ascomyteces was recorded from fowl, less from pigeon and owl and the least (two each on sparrow and parrot droppings. The Basidiomycetes, represented by two species only, were recorded on owl and pigeon droppings. Pigeon droppings yielded the largest number of Deuteromycetes. They were egual in numbers on owl and parrot while on fowl and sparrow their number was comparatively less. Mycelia sterilia, though poor in their numbers, were recorded on all the bird droppings excepting owl.

  20. Drop Impact on Textile Material: Effect of Fabric Properties

    Directory of Open Access Journals (Sweden)

    Romdhani Zouhaier

    2014-09-01

    Full Text Available This paper presents an experimental study of impact of water drop on a surface in a spreading regime with no splashing. Three surfaces were studied: virgin glass, coating film and woven cotton fabric at different construction parameters. All experiments were carried out using water drop with the same free fall high. Digidrop with high-resolution camera is used to measure the different parameters characterising this phenomenon. Results show an important effect of the height of the free fall on the drop profile and the spreading behaviour. An important drop deformation at the surface impact was observed. Then, fabric construction as the weft count deeply affects the drop impact. For plain weave, an increase of weft count causes a decrease in penetration and increase in the spreading rate. The same result was obtained for coated fabric. Therefore, the impact energy was modified and the drop shape was affected, which directly influenced the spreading rate.

  1. Investor Perceptions of Board Performance

    DEFF Research Database (Denmark)

    Fischer, Paul E.; Gramlich, Jeffrey D.; Miller, Brian P.

    2009-01-01

    This paper provides evidence that uncontested director elections provide informative polls of investor perceptions regarding board performance. We find that higher (lower) vote approval is associated with lower (higher) stock price reactions to subsequent announcements of management turnovers...

  2. Specialty Board on Fluency Disorders

    Science.gov (United States)

    ... or large groups of speech-language pathologists. Speech-language pathologists who are Board Certified Specialists in Fluency may be found on this website by searching name, city(location) or zip code. ...

  3. Institutional Evolution and Corporate Boards

    DEFF Research Database (Denmark)

    Chen, Victor Zitian; Hobdari, Bersant; Sun, Pei

    2014-01-01

    We argue that corporate boards are a dynamic repository of human- and social capital in response to external institutional evolution. Theoretically, integrating institutional economics, agency theory and resource dependence theory, we explain that evolution of market-, legal- and political....... Such particular contexts entail the external competitive environment and the principal-agency relationship in corporate governance, amplify (or weaken) the need for certain type of board roles, and ultimately require corporations to reconfigure the human- and social capital embedded within the board. Additionally......, since the board changes are typically proposed by the block shareholders, whose motivation for doing so is closely associated with a corporation’s financial performance, we further argue that financial performance is a key moderator of the relationships between institutional evolution and changes...

  4. Drop entrainment from the surface of oil mist filters: mechanisms, kinetics, and drop spectra

    OpenAIRE

    Wurster, S.; Kolb, H.; Meyer, J.; Kasper, G.

    2016-01-01

    Oil entrainment from coalescence filters has been characterized by different techniques. Drop spectra and entrainment rates were measured by a combination of techniques from 1 mm over long periods of time. Dominant entrainment mechanism(s) are identified on the basis of comparisons of entrainment rates measured in different regions of the filter surface with rates of air bubble formation, measurements of oil film thickness, as well as visual observations. Experiments are supported by force es...

  5. Evaporation of a sessile water drop and a drop of aqueous salt solution.

    Science.gov (United States)

    Misyura, S Y

    2017-11-07

    The influence of various factors on the evaporation of drops of water and aqueous salt solution has been experimentally studied. Typically, in the studies of drop evaporation, only the diffusive vapor transfer, radiation and the molecular heat conduction are taken into account. However, vapor-gas convection plays an important role at droplet evaporation. In the absence of droplet boiling, the influence of gas convection turns out to be the prevailing factor. At nucleate boiling, a prevailing role is played by bubbles generation and vapor jet discharge at a bubble collapse. The gas convection behavior for water and aqueous salt solution is substantially different. With a growth of salt concentration over time, the influence of the convective component first increases, reaches an extremum and then significantly decreases. At nucleate boiling in a salt solution it is incorrect to simulate the droplet evaporation and the heat transfer in quasi-stationary approximation. The evaporation at nucleate boiling in a liquid drop is divided into several characteristic time intervals. Each of these intervals is characterized by a noticeable change in both the evaporation rate and the convection role.

  6. Employee on Boarding Process Automation

    OpenAIRE

    Khushboo Nalband; Priyanka Jadhav; Geetanjali Salunke

    2017-01-01

    On boarding, also known as organizational socialization, plays a vital role in building the initial relationship between an organization and an employee. It also contributes to an employees’ satisfaction, better performance and greater organizational commitment thus increasing an employees’ effectiveness and productivity in his/her role. Therefore, it is essential that on boarding process of an organization is efficient and effective to improve new employees’ retention. Generally this on boar...

  7. Drop-out from a psychodynamic group psychotherapy outpatient unit.

    Science.gov (United States)

    Jensen, Hans Henrik; Mortensen, Erik Lykke; Lotz, Martin

    2014-11-01

    BACKGROUND. Drop-out from psychotherapy is common and represents a considerable problem in clinical practice and research. Aim. To explore pre-treatment predictors of early and late drop-out from psychodynamic group therapy in a public outpatient unit for non-psychotic disorders in Denmark. Methods. Naturalistic design including 329 patients, the majority with mood, neurotic and personality disorders referred to 39-session group therapy. Predictors were socio-demographic and clinical variables, self-reported symptoms (Symptom Check List-90-Revised) and personality style (Millon Clinical Multiaxial Inventory-II). Drop-out was classified into early and late premature termination excluding patients who dropped out for external reasons. Results. Drop-out comprised 20.6% (68 patients) of the sample. Logistic regression revealed social functioning, vocational training, alcohol problems and antisocial behavior to be related to drop-out. However, early drop-outs had prominent agoraphobic symptoms, lower interpersonal sensitivity and compulsive personality features, and late drop-outs cognitive and somatic anxiety symptoms and antisocial personality features. Clinical and psychological variables accounted for the major part of variance in predictions of drop-out, which ranged from 15.6% to 19.5% (Nagelkerke Pseudo R-Square). Conclusion. Social functioning was consistently associated with drop-out, but personality characteristics and anxiety symptoms differentiated between early and late drop-out. Failure to discriminate between stages of premature termination may explain some of the inconsistencies in the drop-out literature. Clinical implications. Before selection of patients to time-limited psychodynamic groups, self-reported symptoms should be thoroughly considered. Patients with agoraphobic symptoms should be offered alternative treatment. Awareness of and motivation to work with interpersonal issues may be essential for compliance with group therapy.

  8. Isolation of Indonesian Cananga oil by instantaneous controlled pressure drop

    OpenAIRE

    2008-01-01

    The isolation of cananga oil by a new process, Instantaneous Controlled Pressure Drop (DIC), was investigated. This process consists in heating the dry cananga (Cananga odorata Hook. fil. et Thomson,forma macrophylla) flowers for a short time period by steam, followed by an abrupt pressure drop into a vacuum (about 5 kPa). This pressure drop provokes auto-vaporization of the volatile compounds, puffing of flowers, breaking of cell walls and cooling. The effect of the process parameters, namel...

  9. Drop impact and rebound dynamics on an inclined superhydrophobic surface.

    Science.gov (United States)

    Yeong, Yong Han; Burton, James; Loth, Eric; Bayer, Ilker S

    2014-10-14

    Due to its potential in water-repelling applications, the impact and rebound dynamics of a water drop impinging perpendicular to a horizontal superhydrophobic surface have undergone extensive study. However, drops tend to strike a surface at an angle in applications. In such cases, the physics governing the effects of oblique impact are not well studied or understood. Therefore, the objective of this study was to conduct an experiment to investigate the impact and rebound dynamics of a drop at various liquid viscosities, in an isothermal environment, and on a nanocomposite superhydrophobic surface at normal and oblique impact conditions (tilted at 15°, 30°, 45°, and 60°). This study considered drops falling from various heights to create normal impact Weber numbers ranging from 6 to 110. In addition, drop viscosity was varied by decreasing the temperature for water drops and by utilizing water-glycerol mixtures, which have similar surface tension to water but higher viscosities. Results revealed that oblique and normal drop impact behaved similarly (in terms of maximum drop spread as well as rebound dynamics) at low normal Weber numbers. However, at higher Weber numbers, normal and oblique impact results diverged in terms of maximum spread, which could be related to asymmetry and more complex outcomes. These asymmetry effects became more pronounced as the inclination angle increased, to the point where they dominated the drop impact and rebound characteristics when the surface was inclined at 60°. The drop rebound characteristics on inclined surfaces could be classified into eight different outcomes driven primarily by normal Weber number and drop Ohnesorge numbers. However, it was found that these outcomes were also a function of the receding contact angle, whereby reduced receding angles yielded tail-like structures. Nevertheless, the contact times of the drops with the coating were found to be generally independent of surface inclination.

  10. Self-excited hydrothermal waves in evaporating sessile drops

    OpenAIRE

    Sefiane K.; Moffat J.R.; Matar O.K.; Craster R.V.

    2008-01-01

    Pattern formation driven by the spontaneous evaporation of sessile drops of methanol, ethanol, and FC-72 using infrared thermography is observed and, in certain cases, interpreted in terms of hydrothermal waves. Both methanol and ethanol drops exhibit thermal wave trains, whose wave number depends strongly on the liquid volatililty and substrate thermal conductivity. The FC- 72 drops develop cellular structures whose size is proportional to the local thickness. Prior to this work, hydrotherma...

  11. Studying the field induced breakup of acoustically levitated drops

    Science.gov (United States)

    Warschat, C.; Riedel, J.

    2017-10-01

    Coulomb fission of charged droplets (The terms drop and droplet are often used synonymous. Throughout this manuscript, to avoid confusion, the terms drop and droplet will be used for liquid spheres with radii in the millimeter range and the micrometer range, respectively. In our experiments, the first correspond to the parent drop while the latter describes the ejected progeny droplets.) is a well-studied natural phenomenon. Controlled droplet fission is already successfully employed in several technological applications. Still, since the occurring surface rupture relies on the exact understanding and description of the liquid gas boundary, some details are still under debate. Most empirical systematic studies observe falling micrometer droplets passing through the electric field inside a plate capacitor. This approach, although easily applicable and reliable, limits the experimental degrees of freedom regarding the observable time and the maximum size of the drops and can only be performed in consecutive individual observations of different subsequent drops. Here we present a novel setup to study the field induced breakup of acoustically levitated drops. The design does not bear any restrictions towards the temporal window of observation, and allows handling of drops of a tunable radius ranging from 10 μm to several millimeters and a real-time monitoring of one single drop. Our comprehensive study includes a time resolved visual inspection, laser shadowgraphy, laser induced fluorescence imaging, and ambient mass spectrometric interrogation of the nascent Taylor cone. The results shown for a millimeter sized drop, previously inaccessible for Coulomb fission experiments, are mostly comparable with previous results for smaller drops. The major difference is the time scale and the threshold potential of the drop rupture. Both values, however, resemble theoretically extrapolations to the larger radius. The technique allows for a systematic study of breakup behavior of

  12. Reducing Variability in Stress Drop with Root-Mean Acceleration

    Science.gov (United States)

    Crempien, J.; Archuleta, R. J.

    2012-12-01

    Stress drop is a fundamental property of the earthquake source. For a given tectonic region stress drop is assumed to be constant allowing for the scaling of earthquake spectra. However, the variability of the stress drop, either for worldwide catalogs or regional catalogs, is quite large. The variability around the median value is on the order of 1.5 in log10 units. One question that continues to pervade the analysis of stress drop is whether this variability is an inherent characteristic of the Earth or is an artifact of the determination of stress drop via the use of the spectral analysis. It is simple to see that the stress drop determined by seismic moment times corner frequency cubed that errors in the corner frequency will strongly influence the variability in the stress drop. To avoid this strong dependence on corner frequency cubed, we have examined the determination of stress drop based on the approach proposed by Hanks (1979), namely using the root-mean-square acceleration. The stress drop determined using rms acceleration may be advantageous because the stress drop is only affected by the square root of the corner frequency. To test this approach we have determined stress drops for the 2000 Tottori earthquake and its aftershocks. We use both the classic method of fitting to a spectrum as well as using rms acceleration. For a preliminary analysis of eight aftershocks and the mainshock we find that the variability in stress drop is reduced by about a factor of two. This approach needs more careful analysis of more events, which will be shown at the meeting.

  13. Neuromuscular adaptations to 4 weeks of intensive drop jump training in well-trained athletes

    DEFF Research Database (Denmark)

    Alkjær, Tine; Meyland, Jacob; Raffalt, Peter C

    2013-01-01

    This study examined the effects of 4 weeks of intensive drop jump training in well-trained athletes on jumping performance and underlying changes in biomechanics and neuromuscular adaptations. Nine well-trained athletes at high national competition level within sprinting and jumping disciplines...

  14. Mesoscopic analyses of porous concrete under static compression and drop weight impact tests

    DEFF Research Database (Denmark)

    Agar Ozbek, A.S.; Pedersen, R.R.; Weerheijm, J.

    2008-01-01

    was considered as a four-phase material incorporating aggregates, bulk cement paste, interfacial transition zones and meso-size air pores. The stress-displacement relations obtained from static compression tests, the stress values, and the corresponding damage levels provided by the drop weight impact tests were......The failure process in highly porous concrete was analyzed experimentally and numerically. A triaxial visco-plastic damage model and a mesoscale representation of the material composition were considered to reproduce static compression and drop weight impact tests. In the mesoscopic model, concrete...

  15. Geometry of the vapor layer under a leidenfrost drop.

    Science.gov (United States)

    Burton, J C; Sharpe, A L; van der Veen, R C A; Franco, A; Nagel, S R

    2012-08-17

    In the Leidenfrost effect, liquid drops deposited on a hot surface levitate on a thin vapor cushion fed by evaporation of the liquid. This vapor layer forms a concave depression in the drop interface. Using laser-light interference coupled to high-speed imaging, we measured the radius, curvature, and height of the vapor pocket, as well as nonaxisymmetric fluctuations of the interface for water drops at different temperatures. The geometry of the vapor pocket depends primarily on the drop size and not on the substrate temperature.

  16. Oscillating and star-shaped drops levitated by an airflow.

    Science.gov (United States)

    Bouwhuis, Wilco; Winkels, Koen G; Peters, Ivo R; Brunet, Philippe; van der Meer, Devaraj; Snoeijer, Jacco H

    2013-08-01

    We investigate the spontaneous oscillations of drops levitated above an air cushion, eventually inducing a breaking of axisymmetry and the appearance of "star drops". This is strongly reminiscent of the Leidenfrost stars that are observed for drops floating above a hot substrate. The key advantage of this work is that we inject the airflow at a constant rate below the drop, thus eliminating thermal effects and allowing for a better control of the flow rate. We perform experiments with drops of different viscosities and observe stable states, oscillations, and chimney instabilities. We find that for a given drop size the instability appears above a critical flow rate, where the latter is largest for small drops. All these observations are reproduced by numerical simulations, where we treat the drop using potential flow and the gas as a viscous lubrication layer. Qualitatively, the onset of instability agrees with the experimental results, although the typical flow rates are too large by a factor 10. Our results demonstrate that thermal effects are not important for the formation of star drops and strongly suggest a purely hydrodynamic mechanism for the formation of Leidenfrost stars.

  17. Electromagnetic radiation due to nonlinear oscillations of a charged drop

    Science.gov (United States)

    Shiryaeva, S. O.; Grigor'ev, A. N.; Kolbneva, N. Yu.

    2016-03-01

    The nonlinear oscillations of a spherical charged drop are asymptotically analyzed under the conditions of a multimode initial deformation of its equilibrium shape. It is found that if the spectrum of initially excited modes contains two adjacent modes, the translation mode of oscillations is excited among others. In this case, the center of the drop's charge oscillates about the equilibrium position, generating a dipole electromagnetic radiation. It is shown that the intensity of this radiation is many orders of magnitude higher than the intensity of the drop's radiation, which arises in calculations of the first order of smallness and is related to the drop's charged surface oscillations.

  18. Improving BWR fuel critical power without increasing bundle pressure drop

    International Nuclear Information System (INIS)

    Matzner, B.; Shiraishi, L.M.; Danielson, D.W.; Congdon, S.P.

    2004-01-01

    It has been almost axiomatic that BWR fuel bundle critical power performance could not be improved without an accompanying increase in bundle pressure drop. It appeared that in order to increase the bundle dryout resistance it was necessary to perturb the bundle coolant flow paths in some fashion. This resulted in an unacceptable bundle pressure drop increase. However, by adding part length rods to decrease bundle pressure drop and by inserting an extra spacer with rearranged spacer pitch and flow trippers on the channel wall at the top of the bundle to increase critical power it was possible to achieve the goal of increased bundle critical power without pressure drop increase. (author)

  19. Overseeing oversight: governance of quality and safety by hospital boards in the English NHS.

    Science.gov (United States)

    Mannion, Russell; Davies, Huw; Freeman, Tim; Millar, Ross; Jacobs, Rowena; Kasteridis, Panos

    2015-01-01

    To contribute towards an understanding of hospital board composition and to explore board oversight of patient safety and health care quality in the English NHS. We reviewed the theory related to hospital board governance and undertook two national surveys about board management in NHS acute and specialist hospital trusts in England. The first survey was issued to 150 trusts in 2011/2012 and was completed online via a dedicated web tool. A total 145 replies were received (97% response rate). The second online survey was undertaken in 2012/2013 and targeted individual board members, using a previously validated standard instrument on board members' attitudes and competencies (the Board Self-Assessment Questionnaire). A total of 334 responses were received from 165 executive and 169 non-executive board members, providing at least one response from 95 of the 144 NHS trusts then in existence (66% response rate). Over 90% of the English NHS trust boards had 10-15 members. We found no significant difference in board size between trusts of different types (e.g. Foundation Trusts versus non-Foundation Trusts and Teaching Hospital Trusts versus non-Teaching Hospital Trusts). Clinical representation on boards was limited: around 62% had three or fewer members with clinical backgrounds. For about two-thirds of the trusts (63%), board members with a clinical background comprised less than 30% of the members. Boards were using a wide range and mix of quantitative performance metrics and soft intelligence (e.g. walk-arounds, patient stories) to monitor their organisations with regard to patient safety. The Board Self-Assessment Questionnaire data showed generally high or very high levels of agreement with desirable statements of practice in each of its six dimensions. Aggregate levels of agreement within each dimension ranged from 73% (for the dimension addressing interpersonal issues) to 85% (on the political). English NHS boards largely hold a wide range of attitudes and

  20. Insights from the pollination drop proteome and the ovule transcriptome of Cephalotaxus at the time of pollination drop production.

    Science.gov (United States)

    Pirone-Davies, Cary; Prior, Natalie; von Aderkas, Patrick; Smith, Derek; Hardie, Darryl; Friedman, William E; Mathews, Sarah

    2016-05-01

    Many gymnosperms produce an ovular secretion, the pollination drop, during reproduction. The drops serve as a landing site for pollen, but also contain a suite of ions and organic compounds, including proteins, that suggests diverse roles for the drop during pollination. Proteins in the drops of species of Chamaecyparis, Juniperus, Taxus, Pseudotsuga, Ephedra and Welwitschia are thought to function in the conversion of sugars, defence against pathogens, and pollen growth and development. To better understand gymnosperm pollination biology, the pollination drop proteomes of pollination drops from two species of Cephalotaxus have been characterized and an ovular transcriptome for C. sinensis has been assembled. Mass spectrometry was used to identify proteins in the pollination drops of Cephalotaxus sinensis and C. koreana RNA-sequencing (RNA-Seq) was employed to assemble a transcriptome and identify transcripts present in the ovules of C. sinensis at the time of pollination drop production. About 30 proteins were detected in the pollination drops of both species. Many of these have been detected in the drops of other gymnosperms and probably function in defence, polysaccharide metabolism and pollen tube growth. Other proteins appear to be unique to Cephalotaxus, and their putative functions include starch and callose degradation, among others. Together, the proteins appear either to have been secreted into the drop or to occur there due to breakdown of ovular cells during drop production. Ovular transcripts represent a wide range of gene ontology categories, and some may be involved in drop formation, ovule development and pollen-ovule interactions. The proteome of Cephalotaxus pollination drops shares a number of components with those of other conifers and gnetophytes, including proteins for defence such as chitinases and for carbohydrate modification such as β-galactosidase. Proteins likely to be of intracellular origin, however, form a larger component of drops

  1. The Digital Drag and Drop Pillbox

    Science.gov (United States)

    Granger, Bradi B.; Locke, Susan C.; Bowers, Margaret; Sawyer, Tenita; Shang, Howard; Abernethy, Amy P.; Bloomfield, Richard A.; Gilliss, Catherine L.

    2017-01-01

    Objective: We present the design and feasibility testing for the “Digital Drag and Drop Pillbox” (D-3 Pillbox), a skill-based educational approach that engages patients and providers, measures performance, and generates reports of medication management skills. Methods: A single-cohort convenience sample of patients hospitalized with heart failure was taught pill management skills using a tablet-based D-3 Pillbox. Medication reconciliation was conducted, and aptitude, performance (% completed), accuracy (% correct), and feasibility were measured. Results: The mean age of the sample (n = 25) was 59 (36–89) years, 50% were women, 62% were black, 46% were uninsured, 46% had seventh-grade education or lower, and 31% scored very low for health literacy. However, most reported that the D-3 Pillbox was easy to read (78%), easy to repeat-demonstrate (78%), and comfortable to use (tablet weight) (75%). Accurate medication recognition was achieved by discharge in 98%, but only 25% reported having a “good understanding of my responsibilities.” Conclusions: The D-3 Pillbox is a feasible approach for teaching medication management skills and can be used across clinical settings to reinforce skills and medication list accuracy. PMID:28282304

  2. Career drop outs of young elite athletes

    Directory of Open Access Journals (Sweden)

    Petra Fišer

    2007-12-01

    Full Text Available The main problem of the study was to examine the characteristics of sports career drop outs of young elite sportswomen and their adaptation to the post-sport life. The sample included 20 ex-young elite sportswomen, who had brought their successful sport careers to an end before the age of 19. We used a modified interview about sports career termination (Cecić Erpič, 1998 for the investigation of the characteristics of their sports careers. To examine the caracteristics of sport careers we used frequency analysis and cluster analysis. The results showed that the participants mostly stated more than one reason for the termination of their career. The most common reasons for career termination were: lack of motivation, bad relations with trainers or co-competitors and dedication to school or education. After the end of a sports career most of the young sportswomen stayed actively in touch with sport, either as trainers, judges, or they remained engaged in sports for recreation.

  3. The viruses of wild pigeon droppings.

    Directory of Open Access Journals (Sweden)

    Tung Gia Phan

    Full Text Available Birds are frequent sources of emerging human infectious diseases. Viral particles were enriched from the feces of 51 wild urban pigeons (Columba livia from Hong Kong and Hungary, their nucleic acids randomly amplified and then sequenced. We identified sequences from known and novel species from the viral families Circoviridae, Parvoviridae, Picornaviridae, Reoviridae, Adenovirus, Astroviridae, and Caliciviridae (listed in decreasing number of reads, as well as plant and insect viruses likely originating from consumed food. The near full genome of a new species of a proposed parvovirus genus provisionally called Aviparvovirus contained an unusually long middle ORF showing weak similarity to an ORF of unknown function from a fowl adenovirus. Picornaviruses found in both Asia and Europe that are distantly related to the turkey megrivirus and contained a highly divergent 2A1 region were named mesiviruses. All eleven segments of a novel rotavirus subgroup related to a chicken rotavirus in group G were sequenced and phylogenetically analyzed. This study provides an initial assessment of the enteric virome in the droppings of pigeons, a feral urban species with frequent human contact.

  4. That's one small drop for Mankind...

    CERN Multimedia

    Anaïs Schaeffer

    2012-01-01

    In August, the members of an ISOLDE project called LOI88 successfully employed a new technique to study the interaction of metal ions in a liquid. It’s the first time that specific ions have been studied in a liquid medium - a technical achievement that opens promising doors for biochemistry.   In the heart of the LOI88 experiment: this is the point where the metal ions (from the left) enter the drop.  “More than half of the proteins in the human body contain metal ions such as magnesium, zinc and copper,” explains Monika Stachura, a biophysicist at the University of Copenhagen and the LOI88 project leader. “We know that these elements are crucial to a protein’s structure and function but their behaviour and interactions are not known in detail.” Detecting these ions directly in  a body-like environment is problematic as their closed atomic shells make them invisible to most spectroscopic techniques. However, using ...

  5. Novel mRNA-specific effects of ribosome drop-off on translation rate and polysome profile.

    Science.gov (United States)

    Bonnin, Pierre; Kern, Norbert; Young, Neil T; Stansfield, Ian; Romano, M Carmen

    2017-05-01

    The well established phenomenon of ribosome drop-off plays crucial roles in translational accuracy and nutrient starvation responses during protein translation. When cells are under stress conditions, such as amino acid starvation or aminoacyl-tRNA depletion due to a high level of recombinant protein expression, ribosome drop-off can substantially affect the efficiency of protein expression. Here we introduce a mathematical model that describes the effects of ribosome drop-off on the ribosome density along the mRNA and on the concomitant protein synthesis rate. Our results show that ribosome premature termination may lead to non-intuitive ribosome density profiles, such as a ribosome density which increases from the 5' to the 3' end. Importantly, the model predicts that the effects of ribosome drop-off on the translation rate are mRNA-specific, and we quantify their resilience to drop-off, showing that the mRNAs which present ribosome queues are much less affected by ribosome drop-off than those which do not. Moreover, among those mRNAs that do not present ribosome queues, resilience to drop-off correlates positively with the elongation rate, so that sequences using fast codons are expected to be less affected by ribosome drop-off. This result is consistent with a genome-wide analysis of S. cerevisiae, which reveals that under favourable growth conditions mRNAs coding for proteins involved in the translation machinery, known to be highly codon biased and using preferentially fast codons, are highly resilient to ribosome drop-off. Moreover, in physiological conditions, the translation rate of mRNAs coding for regulatory, stress-related proteins, is less resilient to ribosome drop-off. This model therefore allows analysis of variations in the translational efficiency of individual mRNAs by accounting for the full range of known ribosome behaviours, as well as explaining mRNA-specific variations in ribosome density emerging from ribosome profiling studies.

  6. Therapeutic effects of Qishen Yiqi Dropping Pill on myocardial injury induced by chronic hypoxia in rats.

    Science.gov (United States)

    Yu, Fu-Chao; Xu, Yan-Juan; Tong, Jia-Yi; Lu, Zhou-Zhou; Zhang, Xiao-Hui

    2015-10-01

    The present study was designed to determine the effects of a traditional Chinese medicine, called Qishen Yiqi Dropping Pill on chronic hypoxia-induced myocardial injury. To establish a rat chronic hypoxia model to be used in the evaluation of the therapeutic effects of the Qishen Yiqi Dropping Pill, Sprague-Dawley (SD) rats were randomly divided into three groups: the control, model, and treatment groups (n = 10 per group). The animals were housed in a plexiglass container. The control animals were under normal oxygen concentration and the model and treatment groups were exposed to air and nitrogen for 5 weeks. The rats in the treatment group were orally administered the Qishen Yiqi Dropping pill (35 mg·kg(-1)·d(-1)) for 5 weeks. After the treatment, the cardiac function and morphology were analyzed, and the expression levels of hypoxia-inducible factor 1α (HIF-1α) were determined using Western blotting. Our results indicated that the cardiac function was impaired, cell apoptosis was enhanced, and HIF-1α expression was up-regulated in the model group, compared to the control group. These changes were ameliorated by the treatment with the Qishen Yiqi Dropping Pill. In conclusion, Qishen Yiqi Dropping pill can ameliorate myocardial injury induced by chronic hypoxia, improve cardiac function, and decrease myocardial cell apoptosis, which may provide a basis for its clinical use for the treatment of chronic cardiovascular diseases. Copyright © 2015 China Pharmaceutical University. Published by Elsevier B.V. All rights reserved.

  7. Comparison of stretch reflex responses evoked during drop jumping in highly skilled atheles versus untrained subjects.

    Science.gov (United States)

    Judge, L W; Burke, J R

    2015-06-01

    The purpose of the study was to describe changes in the excitability of the stretch reflex response (SRR) during different drop jumps as a function of training background and as an adaptation to a preseason sport-specific resistance training program. Twelve collegiate field event athletes (discus, hammer, javelin, shot put, and weight; 9 males and 3 females) and 12 college-aged control subjects performed the following three jumps: (1) countermovement jump (CMJ); (2) countermovement drop jump; and (3) bounce-drop jump (BDJ). Neuromechanical changes in the performance of drop jumps by athletes were measured during the sport-specific resistance training program. Pre-post testing of drop jump performance by control subjects was included for comparison. For each jump trial, ground reaction forces (GRF), electromyograms (EMG) and cinematographic data were collected. There were no training adaptations. However, jump heights were greater for the athletes than the controls among the different jumps with the jump heights for all subjects being less during the BDJ than CMJ and CDJ. In athletes only, there was a differential modulation of the SRR from the gastrocnemius muscle with different levels of background muscle activity for the CDJ and BDJ. There were changes in excitability of SRR from the gastrocnemius muscle as a function of training background. Interrelated neuromechanical mechanisms to include landing biomechanics, intrinsic musculotendinous tissue properties of the ankle, and centrally regulated motor commands may underlie the facilitation of the SRR from the gastrocnemius muscle in athletes as compared to controls.

  8. Reliability analysis of different structure parameters of PCBA under drop impact

    Science.gov (United States)

    Liu, P. S.; Fan, G. M.; Liu, Y. H.

    2018-03-01

    The establishing process of PCBA is modelled by finite element analysis software ABAQUS. Firstly, introduce the Input-G method and the fatigue life under drop impact are introduced and the mechanism of the solder joint failure in the process of drop is analysed. The main reason of solder joint failure is that the PCB component is suffering repeated tension and compression stress during the drop impact. Finally, the equivalent stress and peel stress of different solder joint and plate-level components under different impact acceleration are also analysed. The results show that the reliability of tin-silver copper joint is better than that of tin- lead solder joint, and the fatigue life of solder joint expectancy decrease as the impact pulse amplitude increases.

  9. The Experiment CPLM (Comportamiento De Puentes Líquidos En Microgravedad) On Board MINISAT 01

    Science.gov (United States)

    Sanz-Andrés, Angel; Rodríguez-De-Francisco, Pablo; Santiago-Prowald, Julián

    2001-03-01

    The Universidad Politécnica de Madrid participates in the MINISAT 01 program as the experiment CPLM responsible. This experiment aims at the study of the fluid behaviour in reduced gravity conditions. The interest of this study is and has been widely recognised by the scientific community and has potential applications in the pharmaceutical and microelectronic technologies (crystal growth), among others. The scientific team which has developed the CPLM experiment has a wide experience in this field and had participate in the performance of a large number of experiments on the fluid behaviour in reduced gravity conditions in flight (Spacelab missions, TEXUS sounding rockets, KC-135 and Caravelle aeroplanes, drop towers, as well as on earth labs (neutral buoyancy and small scale simulations). The experimental equipment used in CPLMis a version of the payload developed for experimentation on drop towers and on board microsatellites as the UPM-Sat 1, adapted to fly on board MINISAT 01.

  10. Chemoembolization Decreases Drop-Off Risk of Hepatocellular Carcinoma Patients on the Liver Transplant List

    International Nuclear Information System (INIS)

    Frangakis, Constantine; Geschwind, Jean-Francois; Kim, Daniel; Chen, Yong; Koteish, Ayman; Hong, Kelvin; Liapi, Eleni; Georgiades, Christos S.

    2011-01-01

    Introduction: The drop-off risk for patients awaiting liver transplantation for hepatocellular carcinoma (HCC) is 22%. Transplant liver availability is expected to worsen, resulting in longer waiting times and increased drop-off rates. Our aim was to determine whether chemoembolization can decrease this risk. Patients and Methods: Eighty-seven consecutive HCC patients listed for liver transplant (Milan criteria) underwent statistical comparability adjustments using the propensity score (Wilcoxon, Fisher’s, and chi-square tests). Forty-three nonchemoembolization patients and 22 chemoembolization patients were comparable for Child-Pugh and Model for End-Stage Liver Disease scores, tumor size and number, alpha fetoprotein (AFP) levels, and cause of cirrhosis. We calculated the risk of dropping off the transplant list by assigning a transplant time to those who dropped off (equal probability with patients who were on the list longer than the patient in question). The significance level was obtained by calculating the simulation distribution of the difference compared with the permutations of chemoembolization versus nonchemoembolization assignment of the patients. Kaplan–Meier estimators (log-rank test) were used to determine survival rates. Results: Median follow-up was 187 ± 110 weeks (range 38 to 435, date of diagnosis). The chemoembolization group had an 80% drop-off risk decrease (15% nonchemoembolization versus 3% chemoembolization, p = 0.04). Although survival was better for the chemoembolization group, it did not reach statistical significance. Two-year survival for the nonchemoembolization and chemoembolization group was 57.3% ± 7.1% and 76.0% ± 7.9%, respectively (p = 0.078). Conclusions: Chemoembolization appears to result in a significant decrease in the risk of dropping off liver transplant list for patients with HCC and results in a tendency toward longer survival.

  11. Changes in ethylene signaling and MADS box gene expression are associated with banana finger drop.

    Science.gov (United States)

    Hubert, O; Piral, G; Galas, C; Baurens, F-C; Mbéguié-A-Mbéguié, D

    2014-06-01

    Banana finger drop was examined in ripening banana harvested at immature (iMG), early (eMG) and late mature green (lMG) stages, with contrasting ripening rates and ethylene sensitivities. Concomitantly, 11 ethylene signal transduction components (ESTC) and 6 MADS box gene expressions were comparatively studied in median (control zone, CZ) and pedicel rupture (drop zone DZ) areas in peel tissue. iMG fruit did not ripen or develop finger drop while eMG and lMG fruits displayed a similar finger drop pattern. Several ESTC and MADS box gene mRNAs were differentially induced in DZ and CZ and sequentially in eMG and lMG fruits. MaESR2, 3 and MaEIL1, MaMADS2 and MaMADS5 had a higher mRNA level in eMG and acted earlier, whereas MaERS1, MaCTR1, MaEIL3/AB266319, MaEIL4/AB266320 and MaEIL5/AB266321, MaMADS4 and to a lesser extent MaMADS2 and 5 acted later in lMG. In this fruit, MaERS1 and 3, MaCTR1, MaEIL3, 4 and MaEIL5/AB266321, and MaMADS4 were enhanced by finger drop, suggesting their specific involvement in this process. MaEIL1, MaMADS1 and 3, induced at comparable levels in DZ and CZ, are probably related to the overall fruit ripening process. These findings led us to consider that developmental cues are the predominant finger drop regulation factor. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  12. GOVERNING BOARD OF THE PENSION FUND

    CERN Multimedia

    2002-01-01

    The Governing Board held its hundred-and-tenth and hundred-and-eleventh meetings on 3 September and 2 October respectively. At the first of these meetings, the Governing Board first heard a report presented by B. Strange and F.-X. Douin of JPMorgan Fleming Asset Management on currency overlay. This system has been in operation since 1997 and has fully achieved its objective of allowing the Fund to diversify its investment positions outside Switzerland while reducing portfolio risk. Although the implementation of this currency overlay policy has resulted in substantial disbursements in the first few years, cashflow over the whole period and especially since the weakening of the dollar has been positive. The Governing Board, on the basis of a proposal by the Investment Committee, will have to take a decision on the average level of overlay to be maintained for the Fund's assets. The ordinary meeting held on the afternoon of the same day was mainly devoted to the examination of a number of technical amendments t...

  13. GUI Application for ATCA-based LLRF Carrier Board Management

    CERN Document Server

    Wychowaniak, Jan; Predki, Pawel; Napieralski, Andrzej

    2011-01-01

    The Advanced Telecommunications Computing Architecture (ATCA) standard describes an efficient and powerful platform, implementation of which was adopted to be used as a base for control systems in high energy physics. The ATCA platform is considered to be applied for the X-ray Free Electron Laser (X-FEL), being built at Deutsches Electronen- Synchrotron (DESY) in Hamburg, Germany. The Low Level Radio Frequency (LLRF) control system is composed of a few ATCA Carrier Boards. Carrier Board hosts Intelligent Platform Management Controller (IPMC), which is developed in compliance with the PICMG specifications. IPMC is responsible for management and monitoring of sub-modules installed on Carrier Boards and pluggable Advanced Mezzanine Card (AMC) modules. The ATCA Shelf Manager is the main control unit of a single ATCA crate, responsible for all power and fan modules and Carrier Boards installed in ATCA shelf. The device provides a system administrator with a set of control and diagnostic capabilities regarding the ...

  14. A pipeline of associative memory boards for track finding

    CERN Document Server

    Annovi, A; Bardi, A; Carosi, R; Dell'Orso, Mauro; Giannetti, P; Iannaccone, G; Morsani, F; Pietri, M; Varotto, G

    2000-01-01

    We present a pipeline of associative memory boards for track finding, which satisfies the requirements of level two triggers of the next LHC experiments. With respect to previous realizations, the pipelined architecture warrants full scalability of the memory bank, increased bandwidth (by one order of magnitude), increased number of detector layers (by a factor 2). Each associative memory board consists of four smaller boards, each containing 32 programmable associative memory chips, implemented with low-cost commercial FPGA. FPGA programming has been optimized for maximum efficiency in terms of pattern density and PCB design has been optimized in terms of modularity and FPGA chip density. A complete AM board has been successfully tested at 40 MHz, and can contain 6.6x10//3 particle trajectories. 7 Refs.

  15. Better Board Meetings in Less Time.

    Science.gov (United States)

    Botch, Ray; Cartwright, Janet

    Based upon the experiences of Black Hawk College (BHC), this two-part report presents guidelines for the effective administration of the meetings of a college's board of trustees. The report first discusses board composition and argues that large boards only complicate and slow down the decision-making process. Specific board responsibilities are…

  16. 7 CFR 930.2 - Board.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Board. 930.2 Section 930.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... Definitions § 930.2 Board. Board means the Cherry Industry Administrative Board established pursuant to § 930...

  17. 7 CFR 982.18 - Board.

    Science.gov (United States)

    2010-01-01

    ... Order Regulating Handling Definitions § 982.18 Board. Board means the Hazelnut Marketing Board... 7 Agriculture 8 2010-01-01 2010-01-01 false Board. 982.18 Section 982.18 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and...

  18. Presidential Search: An Overview for Board Members

    Science.gov (United States)

    Association of Governing Boards of Universities and Colleges, 2012

    2012-01-01

    The selection of a president is a governing board's most important responsibility, and the search process is the board's best opportunity to help guide its institution into a successful new era. This guide outlines the leadership roles during a search (those of the board, the board chair, the search committee, and others), briefs board…

  19. 22 CFR 902.3 - Board staff.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Board staff. 902.3 Section 902.3 Foreign Relations FOREIGN SERVICE GRIEVANCE BOARD ORGANIZATION § 902.3 Board staff. The chairperson shall select the Board's executive secretary and other staff provided for in the Act. The executive secretary and staff...

  20. Advisory Boards: Gateway to Business Engagement

    Science.gov (United States)

    Meeder, Hans; Pawlowski, Brett

    2012-01-01

    Interest has been growing in how to build or manage an effective business advisory board. Developing an advisory board is crucial to keeping CTE programs relevant and viable by engaging the support of business and industry. This article delves into how to build and manage a board, and how to re-energize boards that already exist but may be lacking.

  1. 22 CFR 401.28 - Advisory boards.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Advisory boards. 401.28 Section 401.28 Foreign Relations INTERNATIONAL JOINT COMMISSION, UNITED STATES AND CANADA RULES OF PROCEDURE References § 401.28 Advisory boards. (a) The Commission may appoint a board or boards, composed of qualified persons, to...

  2. Effect of Boarding on Mortality in ICUs.

    Science.gov (United States)

    Stretch, Robert; Della Penna, Nicolás; Celi, Leo Anthony; Landon, Bruce E

    2018-04-01

    Hospitals use a variety of strategies to maximize the availability of limited ICU beds. Boarding, which involves assigning patients to an open bed in a different subspecialty ICU, is one such practice employed when ICU occupancy levels are high, and beds in a particular unit are unavailable. Boarding disrupts the normal geographic colocation of patients and care teams, exposing patients to nursing staff with different training and expertise to those caring for nonboarders. We analyzed whether medical ICU patients boarding in alternative specialty ICUs are at increased risk of mortality. Retrospective cohort study using an instrumental variable analysis to control for unmeasured confounding. A semiparametric bivariate probit estimation strategy was employed for the instrumental model. Propensity score matching and standard logistic regression (generalized linear modeling) were used as robustness checks. The medical ICU of a tertiary care nonprofit hospital in the United States between 2002 and 2012. All medical ICU admissions during the specified time period. None. The study population consisted of 8,429 patients of whom 1,871 were boarders. The instrumental variable model demonstrated a relative risk of 1.18 (95% CI, 1.01-1.38) for ICU stay mortality for boarders. The relative risk of in-hospital mortality among boarders was 1.22 (95% CI, 1.00-1.49). GLM and propensity score matching without use of the instrument yielded similar estimates. Instrumental variable estimates are for marginal patients, whereas generalized linear modeling and propensity score matching yield population average effects. Mortality increased with boarding of critically ill patients. Further research is needed to identify safer practices for managing patients during periods of high ICU occupancy.

  3. Total sleep time severely drops during adolescence.

    Directory of Open Access Journals (Sweden)

    Damien Leger

    Full Text Available UNLABELLED: Restricted sleep duration among young adults and adolescents has been shown to increase the risk of morbidities such as obesity, diabetes or accidents. However there are few epidemiological studies on normal total sleep time (TST in representative groups of teen-agers which allow to get normative data. PURPOSE: To explore perceived total sleep time on schooldays (TSTS and non schooldays (TSTN and the prevalence of sleep initiating insomnia among a nationally representative sample of teenagers. METHODS: Data from 9,251 children aged 11 to 15 years-old, 50.7% of which were boys, as part of the cross-national study 2011 HBSC were analyzed. Self-completion questionnaires were administered in classrooms. An estimate of TSTS and TSTN (week-ends and vacations was calculated based on specifically designed sleep habits report. Sleep deprivation was estimated by a TSTN - TSTS difference >2 hours. Sleep initiating nsomnia was assessed according to International classification of sleep disorders (ICSD 2. Children who reported sleeping 7 hours or less per night were considered as short sleepers. RESULTS: A serious drop of TST was observed between 11 yo and 15 yo, both during the schooldays (9 hours 26 minutes vs. 7 h 55 min.; p<0.001 and at a lesser extent during week-ends (10 h 17 min. vs. 9 h 44 min.; p<0.001. Sleep deprivation concerned 16.0% of chidren aged of 11 yo vs. 40.5% of those of 15 yo (p<0.001. Too short sleep was reported by 2.6% of the 11 yo vs. 24.6% of the 15 yo (p<0.001. CONCLUSION: Despite the obvious need for sleep in adolescence, TST drastically decreases with age among children from 11 to 15 yo which creates significant sleep debt increasing with age.

  4. Detection of bubble nucleation event in superheated drop detector ...

    Indian Academy of Sciences (India)

    2016-12-08

    Dec 8, 2016 ... Superheated drop detector consisting of drops of superheated liquid suspended in polymer or gel matrix is of great demand, mainly ... ing to which as the radiation deposits energy along its path inside the superheated liquid, ... resistance with change in pressure in a system. The frequency response of the ...

  5. Why Did They Not Drop Out? Narratives from Resilient Students

    Science.gov (United States)

    Lessard, Anne; Fortin, Laurier; Marcotte, Diane; Potvin, Pierre; Royer, Egide

    2009-01-01

    There is much to be learned from students who were at-risk for dropping out of school but persevered and graduated. The purpose of the study on which this article is based, was to describe how students who were at-risk for dropping out of school persevered and graduated. The voices of two students are introduced, highlighting the challenges they…

  6. SAW-controlled drop size for flow focusing.

    Science.gov (United States)

    Schmid, Lothar; Franke, Thomas

    2013-05-07

    We demonstrate the regularization of droplet formation by applying a surface acoustic wave (SAW) localized at the flow-focus junction of a drop maker. This allows electronic control of drop size in real time, without changing the flow rates or microchannel dimensions.

  7. Vortex Shedding and Depinning of Wind-Forced Liquid Drops

    Science.gov (United States)

    Simon, Roger; White, Edward

    2017-11-01

    Water drops adhere to solid substrates but can depin when wind forcing exceeds the adhesion force provided by surface tension. Schmucker and White (2012.DFD.M4.6) measured critical wind forcing limits for high-Reynolds-number airflow forcing and found a critical constant Weber number, Wecrit = 8.0 , for a range of drop Bond numbers. This work seeks to identify what behavior is associated with Wecrit = 8.0 and why wind-forced drops depin when they do. One hypothesis suggests that, at high Reynolds numbers, drops depin when their interface natural frequency matches the frequency of air vortex shedding in the separated drop wake. We investigate whether a resonance between vortex shedding and drop interface oscillations is involved with depinning. We measure the shedding frequencies behind solid protuberances of the same size as typical drops and, separately, water-drop interface frequencies. We compare our measured values under different flow conditions to establish whether shedding and interface resonance are related to depinning. 1Supported by the National Science Foundation through Grant CBET-1605947.

  8. 14 CFR 23.725 - Limit drop tests.

    Science.gov (United States)

    2010-01-01

    ... used in the drop test (lbs.); h=specified free drop height (inches); d=deflection under impact of the tire (at the approved inflation pressure) plus the vertical component of the axle travel relative to... must be made on the complete airplane, or on units consisting of wheel, tire, and shock absorber, in...

  9. Evaluation of Sodium Sulphacetamide drops in the Treatment of ...

    African Journals Online (AJOL)

    Sodium sulphacetamide eye drops had been used successfully in the past in the treatment of ophthalmia neonatorium (ON) but its use has decreased remarkably in recent time. The efficacy of 10 percent sodium sulphacetamide eye drops in the treatment of ON was prospectively evaluated in 68 neonates seen in our ...

  10. Student Drop-Out from German Higher Education Institutions

    Science.gov (United States)

    Heublein, Ulrich

    2014-01-01

    28% of students of any one year currently give up their studies in bachelor degree programmes at German higher education institutions. Drop-out is to be understood as the definite termination in the higher education system without obtaining an academic degree. The drop-out rate is thereby calculated with the help of statistical estimation…

  11. Complex cooling water systems optimization with pressure drop consideration

    CSIR Research Space (South Africa)

    Gololo, KV

    2012-12-01

    Full Text Available Pressure drop consideration has shown to be an essential requirement for the synthesis of a cooling water network where reuse/recycle philosophy is employed. This is due to an increased network pressure drop associated with additional reuse...

  12. Reconfigurable Optical Add-Drop Multiplexer Using Microring Resonators

    NARCIS (Netherlands)

    Klein, E.J.; Geuzebroek, D.H.; Kelderman, H.; Sengo, G.; Sengo, G.; Baker, Nigel; Driessen, A.

    2005-01-01

    We report a reconfigurable four-channel optical add–drop multiplexer for use in access networks. The optical add–drop multiplexer (OADM) is based on vertically coupled thermally tunable $Si_3N_4$ – $SiO_2$ microring resonators (MRs) and has been realized on a footprint of 0.25 mm2. Individual MRs in

  13. Drop shape visualization and contact angle measurement on curved surfaces.

    Science.gov (United States)

    Guilizzoni, Manfredo

    2011-12-01

    The shape and contact angles of drops on curved surfaces is experimentally investigated. Image processing, spline fitting and numerical integration are used to extract the drop contour in a number of cross-sections. The three-dimensional surfaces which describe the surface-air and drop-air interfaces can be visualized and a simple procedure to determine the equilibrium contact angle starting from measurements on curved surfaces is proposed. Contact angles on flat surfaces serve as a reference term and a procedure to measure them is proposed. Such procedure is not as accurate as the axisymmetric drop shape analysis algorithms, but it has the advantage of requiring only a side view of the drop-surface couple and no further information. It can therefore be used also for fluids with unknown surface tension and there is no need to measure the drop volume. Examples of application of the proposed techniques for distilled water drops on gemstones confirm that they can be useful for drop shape analysis and contact angle measurement on three-dimensional sculptured surfaces. Copyright © 2011 Elsevier Inc. All rights reserved.

  14. The origin of star-shaped oscillations of Leidenfrost drops

    Science.gov (United States)

    Ma, Xiaolei; Burton, Justin C.

    We experimentally investigate the oscillations of Leidenfrost drops of water, liquid nitrogen, ethanol, methanol, acetone and isopropyl alcohol. The drops levitate on a cushion of evaporated vapor over a hot, curved surface which keeps the drops stationary. We observe star-shaped modes along the periphery of the drop, with mode numbers n = 2 to 13. The number of observed modes is sensitive to the properties of the liquid. The pressure oscillation frequency in the vapor layer under the drop is approximately twice that of the drop frequency, which is consistent with a parametric forcing mechanism. However, the Rayleigh and thermal Marangoni numbers are of order 10,000, indicating that convection should play a dominating role as well. Surprisingly, we find that the wavelength and frequency of the oscillations only depend on the thickness of the liquid, which is twice the capillary length, and do not depend on the mode number, substrate temperature, or the substrate curvature. This robust behavior suggests that the wavelength for the oscillations is set by thermal convection inside the drop, and is less dependent on the flow in the vapor layer under the drop

  15. Simulation of the drop impact test for moulded thermoplastic containers

    NARCIS (Netherlands)

    Reed, P.E.; Breedveld, G.; Lim, B.C.

    2000-01-01

    An analysis is made of the drop impact test for moulded plastics containers, as a first step towards the simulation of the impact event for design and development purposes. Experimental data are analysed from instrumented base drop impact testing of water-filled blow-moulded bottles, 20 and 210 l

  16. The new Board of Governors

    International Nuclear Information System (INIS)

    1964-01-01

    Full text: Miss Blanche Margaret Meagher was elected chairman of the IAEA Board of Governors for 1964-65, after the new Board had been constituted at the Eighth Session of the General Conference in September. Since 1962 Miss Meagher has been Canadian Ambassador to Austria, and Canadian Governor of the Agency. Miss Meagher joined the Canadian Department of External Affairs in 1942, and has held a number of foreign diplomatic appointments; she has also served on Canadian delegations to the UN Educational, Scientific and Cultural Organization, the International Telecommunication Union, the Economic and Social Council of UN and the UN Disarmament Sub-Committee. The Vice-Chairmen of the Board are Mr. Wilhelm Billig (Poland) and Mr. Hassan M. Tohamy (UAR). Mr. Billig is Chairman of the State Council for Atomic Energy, and High Commissioner for Peaceful Uses of Atomic Energy. Mr. Tohamy is Ambassador to Austria, and Resident Representative to the Agency. Of the twelve elected members of the Board, five were chosen by the General Conference in 1964 for two years, viz. Argentina, Chile, Netherlands, Thailand and the United Arab Republic. Seven were elected in 1963: Afghanistan, China, Congo (Leopoldville), Morocco, Romania, Switzerland and Uruguay. The remaining thirteen members have been designated by the Board: Australia, Belgium, Brazil, Canada, Finland, France, India, Japan, Poland, South Africa, USSR, United Kingdom and United States. (author)

  17. 29 CFR 4002.3 - Board of Directors, Chair, and Representatives of Board Members.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 9 2010-07-01 2010-07-01 false Board of Directors, Chair, and Representatives of Board... CORPORATION GENERAL BYLAWS OF THE PENSION BENEFIT GUARANTY CORPORATION § 4002.3 Board of Directors, Chair, and... Labor shall be the Chair of the Board of Directors and shall call and preside over all Board meetings...

  18. Tunable transport of drops on a vibrating inclined fiber

    Science.gov (United States)

    Bick, Alison; Boulogne, François; Sauret, Alban; Stone, Howard A.

    2015-11-01

    Transport of liquid drops in fibrous media occurs in various engineering systems such as fog harvesting or cleaning of textiles. The ability to tune or to control liquid movement can increase the system efficiency and enable new engineering applications. In this letter, we experimentally investigate how partially wetting drops on a single fiber can be manipulated by vibrating the fiber. We show that a sliding motion along the fiber or a dripping of the drop can be triggered by standing waves. We identify the conditions on the drop volume, the fiber tilt angle, and the amplitude and frequency of oscillations to observe these different behaviors. Finally, we experimentally illustrate that vibrations can be used to control the transport and the collection of water drops along a fiber using a combination of the sliding and dripping transitions.

  19. Capillary-inertial colloidal catapults upon drop coalescence

    Science.gov (United States)

    Chen, Chuan-Hua

    2016-01-01

    Surface energy released upon drop coalescence is known to power the self-propelled jumping of liquid droplets on superhydrophobic solid surfaces, and the jumping droplets can additionally carry colloidal payloads toward self-cleaning. Here, we show that drop coalescence on a spherical particle leads to self-propelled launching of the particle from virtually any solid surface. The main prerequisite is an intermediate wettability of the particle, such that the momentum from the capillary-inertial drop coalescence process can be transferred to the particle. By momentum conservation, the launching velocity of the particle-drop complex is proportional to the capillary-inertial velocity based on the drop radius and to the fraction of the liquid mass in the total mass. The capillary-inertial catapult is not only an alternative mechanism for removing colloidal contaminants, but also a useful model system for studying ballistospore launching. PMID:27478201

  20. Silicon wavelength-selective partial-drop broadcast filter bank.

    Science.gov (United States)

    Su, Zhan; Cherchi, Matteo; Timurdogan, Erman; Sun, Jie; Moresco, Michele; Leake, Gerald; Coolbaugh, Douglas; Watts, Michael R

    2014-09-15

    We propose an approach to a wavelength-selective 1×N port optical broadcast network demonstrating the approach in a 1×8 port parallel optical drop filter bank utilizing adiabatic micro-ring tunable filters. The micro-ring filters exhibit first-order 92.7±3.7 GHz full width at half-maximum bandwidths with a 36.2 nm free spectral range, low-drop power variation (0.11 dB), and aggregate excess loss of only 1.1 dB in all drop ports. Error-free operation at a 10 Gbit/s data rate is achieved for all eight drop ports with less than a 0.5 dB power penalty among the ports. This wavelength-selective parallel-drop approach serves as a building block for on-chip all-to-all communication networks.

  1. Drop tests of the Three Mile Island knockout canister

    International Nuclear Information System (INIS)

    Box, W.D.; Aaron, W.S.; Shappert, L.B.; Childress, P.C.; Quinn, G.J.; Smith, J.V.

    1987-01-01

    A type of Three Mile Island Unit 2 (TMI-2) defueling canister, called a ''knockout'' canister, was subjected to a series of drop tests at the Oak Ridge National Laboratory's Drop Test Facility. These tests confirmed the structural integrity of internal fixed neutron poisons in support of a request for NRC licensing of this type of canister for the shipment of TMI-2 reactor fuel debris to the Idaho National Engineering Laboratory (INEL) for the Core Examination R and D Program. This report presents the data generated and the results obtained from a series of four drop tests that included two drops with the test assembly in the vertical position and two drops with the assembly in the horizontal position

  2. About applicability of thermodynamic parameters to small drops and clusters

    Science.gov (United States)

    Kharlamov, G. V.; Onischuk, A. A.; Vosel, S. V.; Purtov, P. A.

    2012-11-01

    In our paper the results of molecular dynamics calculations of nanodrops are presented. The density profiles, the Irving-Kirkwood pressure tensors, the chemical potentials of the systems, the equimolar radii of the drops and the radii of tension, the mechanical and thermodynamic surface tensions have been calculated. It is shown that both the mechanical and thermodynamic surface tensions decrease with the decrease of the equimolar radius of the drop and reach zero at the same R0 depending on temperature. With the further equimolar radius decrease the surface tension becomes negative. It means that such droplet is metastable and that the notion of the macroscopic surface tension cannot be applied to such small drops. The dependence of the ratio of the drop surface tension to the surface tension of the flat liquid-vapor interface on the ratio of the drop equimolar radius to R0 is a universal function.

  3. About applicability of thermodynamic parameters to small drops and clusters

    International Nuclear Information System (INIS)

    Kharlamov, G V; Onischuk, A A; Vosel, S V; Purtov, P A

    2012-01-01

    In our paper the results of molecular dynamics calculations of nanodrops are presented. The density profiles, the Irving-Kirkwood pressure tensors, the chemical potentials of the systems, the equimolar radii of the drops and the radii of tension, the mechanical and thermodynamic surface tensions have been calculated. It is shown that both the mechanical and thermodynamic surface tensions decrease with the decrease of the equimolar radius of the drop and reach zero at the same R 0 depending on temperature. With the further equimolar radius decrease the surface tension becomes negative. It means that such droplet is metastable and that the notion of the macroscopic surface tension cannot be applied to such small drops. The dependence of the ratio of the drop surface tension to the surface tension of the flat liquid-vapor interface on the ratio of the drop equimolar radius to R 0 is a universal function.

  4. Building micro-soccer-balls with evaporating colloidal fakir drops

    Science.gov (United States)

    Gelderblom, Hanneke; Marín, Álvaro G.; Susarrey-Arce, Arturo; van Housselt, Arie; Lefferts, Leon; Gardeniers, Han; Lohse, Detlef; Snoeijer, Jacco H.

    2013-11-01

    Drop evaporation can be used to self-assemble particles into three-dimensional microstructures on a scale where direct manipulation is impossible. We present a unique method to create highly-ordered colloidal microstructures in which we can control the amount of particles and their packing fraction. To this end, we evaporate colloidal dispersion drops from a special type of superhydrophobic microstructured surface, on which the drop remains in Cassie-Baxter state during the entire evaporative process. The remainders of the drop consist of a massive spherical cluster of the microspheres, with diameters ranging from a few tens up to several hundreds of microns. We present scaling arguments to show how the final particle packing fraction of these balls depends on the drop evaporation dynamics, particle size, and number of particles in the system.

  5. A precise goniometer/tensiometer using a low cost single-board computer

    Science.gov (United States)

    Favier, Benoit; Chamakos, Nikolaos T.; Papathanasiou, Athanasios G.

    2017-12-01

    Measuring the surface tension and the Young contact angle of a droplet is extremely important for many industrial applications. Here, considering the booming interest for small and cheap but precise experimental instruments, we have constructed a low-cost contact angle goniometer/tensiometer, based on a single-board computer (Raspberry Pi). The device runs an axisymmetric drop shape analysis (ADSA) algorithm written in Python. The code, here named DropToolKit, was developed in-house. We initially present the mathematical framework of our algorithm and then we validate our software tool against other well-established ADSA packages, including the commercial ramé-hart DROPimage Advanced as well as the DropAnalysis plugin in ImageJ. After successfully testing for various combinations of liquids and solid surfaces, we concluded that our prototype device would be highly beneficial for industrial applications as well as for scientific research in wetting phenomena compared to the commercial solutions.

  6. Formulation of indomethacin eye drops via complexation with cyclodextrins.

    Science.gov (United States)

    Halim Mohamed, Maaly A; Mahmoud, Azza A

    2011-03-01

    Topically administered indomethacin is used in the management and prevention of ocular inflammation and cystoid macular edema related to cataract surgery and in the maintenance of mydriasis during cataract surgery. Pharmaceutically, the main obstacle in formulating indomethacin as eye drops is its low solubility and aqueous instability. Inclusion complexation of indomethacin with cyclodextrins (CDs) was our interest in this research to obtain stable and effective aqueous indomethacin eye drops. The influence of β-CD, hydroxypropyl-β-CD (HP-β-CD), and sulfobutyl ether-β-CD (SBE-β-CD) on indomethacin solubility was investigated. Indomethacin-HP-β-CD complex was prepared and characterized by infrared spectroscopy, differential scanning calorimetry, and X-ray diffractometry and was subjected to in vitro release and stability studies. The anti-inflammatory effect of formulated indomethacin-HP-β-CD eye drops on chemically burned albino rabbit eyes was compared to those of Indocollyre(®) and Voltaren(®) eye drops. HP-β-CD was found to have a high solubilizing effect towards indomethacin and was thus selected for its formulation. Formulated indomethacin-HP-β-CD eye drops exhibited delayed release and high drug stability compared to the drug solution. Draize rabbit eye irritation test and histological examination on albino rabbit eyes treated with indomethacin-HP-β-CD eye drops revealed that these eye drops were non-irritant. The anti-inflammatory studies indicated that formulating indomethacin eye drops via complexation with HP-β-CD significantly improves the therapeutic efficacy of the indomethacin compared to the investigated eye drops. An aqueous ocular delivery system for the poor water soluble anti-inflammatory indomethacin was prepared using HP-β-CD as a complexing agent. Besides a sufficient solubility for the drug, many factors were studied in the development of this system, such as stability and safety. In addition, indomethacin-HP-β-CD eye drops

  7. Examining Creativity of Students through Smart Board in Learning Mathematics

    Directory of Open Access Journals (Sweden)

    Mohammad-Hassan Behzadi

    2013-03-01

    Full Text Available In present era, students and teachers need possibilities that ease teaching and learning process. Electronic instruments such as computer, software, and smart instruments will increase abilities for students. The purpose of this study is to examine the creativity level of high school students in the learning environment using smart board and compare it to traditional environment. Participants of this study were consisted of girl students at second grade. One girly high school is selected by semi-cluster sampling method. Research method is implemented via quasi-experimental method using pretest and posttest for control and experiment groups which are same at scientific level. Based on the result of this research via Leven and T-tests, it is indicated that there is significant difference between creativity level of the students who learn mathematics using smart board and the students who learn mathematics via traditional method. Therefore it seems that using smart board will ease mathematical learning process.

  8. Institutional Evolution and Corporate Boards

    DEFF Research Database (Denmark)

    Chen, Victor Zitian; Hobdari, Bersant; Sun, Pei

    2014-01-01

    We argue that corporate boards are a dynamic repository of human- and social capital in response to external institutional evolution. Theoretically, integrating institutional economics, agency theory and resource dependence theory, we explain that evolution of market-, legal- and political...... institutions restructures the particular context in which board members play their two primary roles: monitoring the CEO on behalf of the shareholders, suggested by the agency theory, and supporting the CEO by providing resources, knowledge and information, suggested by the resource dependence theory......, since the board changes are typically proposed by the block shareholders, whose motivation for doing so is closely associated with a corporation’s financial performance, we further argue that financial performance is a key moderator of the relationships between institutional evolution and changes...

  9. Controlling electronics boards with PVSS

    CERN Document Server

    Jacobsson, Richard

    2005-01-01

    This paper addresses several aspects of implementing a control system for electronics boards in order to perform remote Field Programmable Gate Array (FPGA) programming, hardware configuration, register control, and monitoring, as well as interfacing it to an expert system. The paper presents an implementation, using the Distributed Information Management (DIM) package and the industrial SCADA system PVSS II from ETM, in which the access mechanisms to the board resources are completely generic and in which the device prescription and the handling of mapping between functional parameters and physical registers follow a common structure independent of the board type. The control system also incorporates mechanisms by which it may be controlled from a finite state machine based expert system. Finally the paper suggests an improvement in which the mapping between logical parameters and physical registers is represented by descriptors in the device description such that the translation can be handled by a common m...

  10. Patients Prefer Boarding in Inpatient Hallways: Correlation with the National Emergency Department Overcrowding Score

    Science.gov (United States)

    Richards, John R.; Ozery, Gal; Notash, Mark; Sokolove, Peter E.; Derlet, Robert W.; Panacek, Edward A.

    2011-01-01

    Objective. The boarding of patients in Emergency Department (ED) hallways when no inpatient beds are available is a major cause of ED crowding. One solution is to board admitted patients in an inpatient rather than ED hallway. We surveyed patients to determine their preference and correlated their responses to real-time National Emergency Department Overcrowding Score (NEDOCS). Methods. This was a survey of admitted patients in the ED of an urban university level I trauma center serving a community of 5 million about their personal preferences regarding boarding. Real-time NEDOCS was calculated at the time each survey was conducted. Results. 99 total surveys were completed during October 2010, 42 (42%) patients preferred to be boarded in an inpatient hallway, 33 (33%) preferred the ED hallway, and 24 (24%) had no preference. Mean (±SD) NEDOCS (range 0–200) was 136 ± 46 for patients preferring inpatient boarding, 112 ± 39 for ED boarding, and 119 ± 43 without preference. Male patients preferred inpatient hallway boarding significantly more than females. Preference for inpatient boarding was associated with a significantly higher NEDOCS. Conclusions. In this survey study, patients prefer inpatient hallway boarding when the hospital is at or above capacity. Males prefer inpatient hallway boarding more than females. The preference for inpatient hallway boarding increases as the ED becomes more crowded. PMID:22235374

  11. Patients prefer boarding in inpatient hallways: correlation with the national emergency department overcrowding score.

    Science.gov (United States)

    Richards, John R; Ozery, Gal; Notash, Mark; Sokolove, Peter E; Derlet, Robert W; Panacek, Edward A

    2011-01-01

    Objective. The boarding of patients in Emergency Department (ED) hallways when no inpatient beds are available is a major cause of ED crowding. One solution is to board admitted patients in an inpatient rather than ED hallway. We surveyed patients to determine their preference and correlated their responses to real-time National Emergency Department Overcrowding Score (NEDOCS). Methods. This was a survey of admitted patients in the ED of an urban university level I trauma center serving a community of 5 million about their personal preferences regarding boarding. Real-time NEDOCS was calculated at the time each survey was conducted. Results. 99 total surveys were completed during October 2010, 42 (42%) patients preferred to be boarded in an inpatient hallway, 33 (33%) preferred the ED hallway, and 24 (24%) had no preference. Mean (±SD) NEDOCS (range 0-200) was 136 ± 46 for patients preferring inpatient boarding, 112 ± 39 for ED boarding, and 119 ± 43 without preference. Male patients preferred inpatient hallway boarding significantly more than females. Preference for inpatient boarding was associated with a significantly higher NEDOCS. Conclusions. In this survey study, patients prefer inpatient hallway boarding when the hospital is at or above capacity. Males prefer inpatient hallway boarding more than females. The preference for inpatient hallway boarding increases as the ED becomes more crowded.

  12. Patients Prefer Boarding in Inpatient Hallways: Correlation with the National Emergency Department Overcrowding Score

    Directory of Open Access Journals (Sweden)

    John R. Richards

    2011-01-01

    Full Text Available Objective. The boarding of patients in Emergency Department (ED hallways when no inpatient beds are available is a major cause of ED crowding. One solution is to board admitted patients in an inpatient rather than ED hallway. We surveyed patients to determine their preference and correlated their responses to real-time National Emergency Department Overcrowding Score (NEDOCS. Methods. This was a survey of admitted patients in the ED of an urban university level I trauma center serving a community of 5 million about their personal preferences regarding boarding. Real-time NEDOCS was calculated at the time each survey was conducted. Results. 99 total surveys were completed during October 2010, 42 (42% patients preferred to be boarded in an inpatient hallway, 33 (33% preferred the ED hallway, and 24 (24% had no preference. Mean (±SD NEDOCS (range 0–200 was 136±46 for patients preferring inpatient boarding, 112±39 for ED boarding, and 119±43 without preference. Male patients preferred inpatient hallway boarding significantly more than females. Preference for inpatient boarding was associated with a significantly higher NEDOCS. Conclusions. In this survey study, patients prefer inpatient hallway boarding when the hospital is at or above capacity. Males prefer inpatient hallway boarding more than females. The preference for inpatient hallway boarding increases as the ED becomes more crowded.

  13. French Board of Orthodontics.

    Science.gov (United States)

    De Sousa Beltrao, Paulo Augusto

    2010-09-01

    A. February 2001 (15.11 y). Molar Class I, skeletal Class I, normodivergent, anterior deficiency: -17 mm, bimaxillary protrusion. Preparation of arches (alignment, levelling, canine retraction). Correction of arches (space closure). Occlusal finishing (artistic bends). B. POSTTREATMENT RECORDS: February 2003 (17.11 y). Maxillary Hawley plate for nighttime use and bonded lingual wire from 33 to 43. C. POSTRETENTION RECORDS: December 2003 (18.9 y). Copyright © 2010 CEO. Published by Elsevier Masson SAS. All rights reserved.

  14. Prevalence of self-reported early glaucoma eye drop bottle exhaustion and associated risk factors: a patient survey.

    Science.gov (United States)

    Moore, Daniel B; Walton, Charlene; Moeller, Kristy L; Slabaugh, Mark A; Mudumbai, Raghu C; Chen, Philip P

    2014-06-13

    One barrier to patient adherence with chronic topical glaucoma treatment is an inadequate amount of medication available between prescription refills. We examined the self-reported prevalence of early exhaustion of glaucoma eye drops prior to a scheduled refill, and associated risk factors. This cross-sectional survey was performed at a University-based clinical practice. Glaucoma patients at the University of Washington who were experienced with eye drop application and were on a steady regimen of self-administered glaucoma drops in both eyes took a survey at the time of clinic examination. The main outcome measure was self-reported early eye drop bottle exhaustion. 236 patients were eligible and chose to participate. In general, patients included were relatively healthy (mean 2.3 comorbid medical conditions). Sixty patients (25.4%) reported any problem with early exhaustion of eye drop bottles, and this was associated with visual acuity ≤ 20/70 in the better eye (P = .049). Twelve patients (5.1%) reported that they "often" (5-7 times per year), "usually" (8-11 times per year) or "always" ran out of eye drops prior to a scheduled refill. Patients affected by this higher level (≥ 5 times yearly) of eye drop bottle exhaustion were more likely to have poor visual acuity in their worse eye ≤  20/70 (P = .015) and had significantly lower worse-eye logMAR (P = .043). Self-reported early glaucoma bottle exhaustion regularly affected 5% of patients in our population and 25% reported early exhaustion at least once; the main risk factor was poor vision in at least one eye. These results may not be generalizable to a broad patient population, or to those inexperienced with eye drop self-administration. However, this pilot study compels further evaluation and consideration of early eye drop bottle exhaustion in glaucoma patients.

  15. [The role of university hospital executive board members].

    Science.gov (United States)

    Debatin, J F; Rehr, J

    2009-09-01

    Demographic changes and medical progress in combination with vastly altered regulatory and economic environments have forced considerable change in the structure of German university hospitals in recent years. These changes have affected medical care as well as research and medical school training. To allow for more flexibility and a higher level of reactivity to the changing environment German university hospitals were transferred from state agencies to independent corporate structures. All but one remains wholly owned by the respective state governments. The governing structure of these independent medical hospitals consists of an executive board, generally made up of a medical director, a financial director, a director for nursing, and the dean of the medical faculty. In most hospitals, the medical director serves as chief executive officer. The regulations governing the composition and responsibility of the members of the executive board differ from state to state. These differences do affect to some degree the interactive effectiveness of the members of the executive boards. Modalities that stress the overall responsibility for all board members seem to work better than those that define clear portfolio limits. Even more than organizational and regulatory differences, the effectiveness of the work of the executive boards is influenced by the personality of the board members themselves. Success appears to be a clear function of the willingness of all members to work together.

  16. The Development of Embedded Local Monitor Board (ELMB)

    CERN Document Server

    Boterenbrood, H; 9th Workshop On Electronics For Lhc Experiments

    2003-01-01

    The Embedded Local Monitor Board (ELMB) is a credit-card sized plug-on board, designed as a general-purpose CAN-bus based building block for various control and monitoring tasks in the LHC experiments. The latest and final version of the hardware in combination with the firmware shows to have even better radiation tolerance than before. This and the ELMB's low cost, low power consumption, software support - both low-level and high-level - have made the ELMB the solution of choice in a wide variety of control and monitoring applications. For the LHC experiments a total of ca. 10000 pieces will be produced.

  17. Effect of humidity on the filter pressure drop

    International Nuclear Information System (INIS)

    Vendel, J.; Letourneau, P.

    1995-01-01

    The effects of humidity on the filter pressure drop have been reported in some previous studies in which it is difficult to draw definite conclusions. These studies show contradictory effects of humidity on the pressure drop probably due to differences in the hygroscopicity of the test aerosols. The objective of this paper is to present experimental results on the evolution of the filter pressure drop versus mass loading, for different test aerosols and relative humidities. Present results are compared to those found in various publication. An experimental device has been designed to measure filter pressure drop as the function of the areal density for relative humidity varying in the range of 9 % to 85 %. Experiments have been conducted with hygroscopic: (CsOH) and nonhygroscopic aerosols (TiO 2 ). Cesium hydroxyde (CsOH) of size of 2 μ M AMMD has been generated by an ultrasonic generator and the 0.7 μm AMMD titanium oxyde has been dispersed by a open-quotes turn-tableclose quotes generator. As it is noted in the BISWAS'publication [3], present results show, in the case of nonhygroscopic aerosols, a linear relationship of pressure drop to mass loading. For hygroscopic aerosols two cases must be considered: for relative humidity below the deliquescent point of the aerosol, the relationship of pressure drop to mass loading remains linear; above the deliquescent point, the results show a sudden increase in the pressure drop and the mass capacity of the filter is drastically reduced

  18. Effect of humidity on the filter pressure drop

    Energy Technology Data Exchange (ETDEWEB)

    Vendel, J.; Letourneau, P. [Institut de Protection et de Surete Nucleaire, Gif-sur-Yvette (France)

    1995-02-01

    The effects of humidity on the filter pressure drop have been reported in some previous studies in which it is difficult to draw definite conclusions. These studies show contradictory effects of humidity on the pressure drop probably due to differences in the hygroscopicity of the test aerosols. The objective of this paper is to present experimental results on the evolution of the filter pressure drop versus mass loading, for different test aerosols and relative humidities. Present results are compared to those found in various publication. An experimental device has been designed to measure filter pressure drop as the function of the areal density for relative humidity varying in the range of 9 % to 85 %. Experiments have been conducted with hygroscopic: (CsOH) and nonhygroscopic aerosols (TiO{sub 2}). Cesium hydroxyde (CsOH) of size of 2 {mu} M AMMD has been generated by an ultrasonic generator and the 0.7 {mu}m AMMD titanium oxyde has been dispersed by a {open_quotes}turn-table{close_quotes} generator. As it is noted in the BISWAS`publication [3], present results show, in the case of nonhygroscopic aerosols, a linear relationship of pressure drop to mass loading. For hygroscopic aerosols two cases must be considered: for relative humidity below the deliquescent point of the aerosol, the relationship of pressure drop to mass loading remains linear; above the deliquescent point, the results show a sudden increase in the pressure drop and the mass capacity of the filter is drastically reduced.

  19. Thermal infrared mapping of the Leidenfrost drop evaporation

    Science.gov (United States)

    Wciślik, Sylwia

    2016-09-01

    The paper presents an author complementary study on the Leidenfrost drop evaporation. The research was conducted under ambient conditions and in the film boiling regime. Large water drops were placed on the copper substrate of the constant temperature Tw ranging from 297.6 to 404oC. The initial single drop diameter and its mass was D0 ≈ 1cm and m0 ≈ 1g respectively. One of the obtained results, for each Tw are the drop thermal images versus time. They were used to calculate an average temperature over the drop upper surface (Td). For an exemplary heating surface temperature of Tw = 297.6oC the average drop temperature is approximately 11oC lower than the saturation one and equals Td = 88,95oC. This value is estimated for the first 200s of evaporation and with time step size Δt = 0,5s. The drop upper surface temperature is highly variable and indicates strong convection inside it. This is due to the complex nature of heat and mass transfer. The maximum standard deviation from Td = 88,95oC is SD = 1.21.

  20. Inverse Leidenfrost effect: self-propelling drops on a bath

    Science.gov (United States)

    Gauthier, Anais; van der Meer, Devaraj; Lohse, Detlef; Physics of Fluids Team

    2017-11-01

    When deposited on very hot solid, volatile drops can levitate over a cushion of vapor, in the so-called Leidenfrost state. This phenomenon can also be observed on a hot bath and similarly to the solid case, drops are very mobile due to the absence of contact with the substrate that sustains them. We discuss here a situation of ``inverse Leidenfrost effect'' where room-temperature drops levitate on a liquid nitrogen pool - the vapor is generated here by the bath sustaining the relatively hot drop. We show that the drop's movement is not random: the liquid goes across the bath in straight lines, a pattern only disrupted by elastic bouncing on the edges. In addition, the drops are initially self-propelled; first at rest, they accelerate for a few seconds and reach velocities of the order of a few cm/s, before slowing down. We investigate experimentally the parameters that affect their successive acceleration and deceleration, such as the size and nature of the drops and we discuss the origin of this pattern.

  1. Application of Proteomics to the Study of Pollination Drops

    Directory of Open Access Journals (Sweden)

    Natalie Prior

    2013-04-01

    Full Text Available Premise of the study: Pollination drops are a formative component in gymnosperm pollen-ovule interactions. Proteomics offers a direct method for the discovery of proteins associated with this early stage of sexual reproduction. Methods: Pollination drops were sampled from eight gymnosperm species: Chamaecyparis lawsoniana (Port Orford cedar, Ephedra monosperma, Ginkgo biloba, Juniperus oxycedrus (prickly juniper, Larix ×marschlinsii, Pseudotsuga menziesii (Douglas-fir, Taxus ×media, and Welwitschia mirabilis. Drops were collected by micropipette using techniques focused on preventing sample contamination. Drop proteins were separated using both gel and gel-free methods. Tandem mass spectrometric methods were used including a triple quadrupole and an Orbitrap. Results: Proteins are present in all pollination drops. Consistency in the protein complement over time was shown in L. ×marschlinsii. Representative mass spectra from W. mirabilis chitinase peptide and E. monosperma serine carboxypeptidase peptide demonstrated high quality results. We provide a summary of gymnosperm pollination drop proteins that have been discovered to date via proteomics. Discussion: Using proteomic methods, a dozen classes of proteins have been identified to date. Proteomics presents a way forward in deepening our understanding of the biological function of pollination drops.

  2. Heat exchange between a bouncing drop and a superhydrophobic substrate.

    Science.gov (United States)

    Shiri, Samira; Bird, James C

    2017-07-03

    The ability to enhance or limit heat transfer between a surface and impacting drops is important in applications ranging from industrial spray cooling to the thermal regulation of animals in cold rain. When these surfaces are micro/nanotextured and hydrophobic, or superhydrophobic, an impacting drop can spread and recoil over trapped air pockets so quickly that it can completely bounce off the surface. It is expected that this short contact time limits heat transfer; however, the amount of heat exchanged and precise role of various parameters, such as the drop size, are unknown. Here, we demonstrate that the amount of heat exchanged between a millimeter-sized water drop and a superhydrophobic surface will be orders of magnitude less when the drop bounces than when it sticks. Through a combination of experiments and theory, we show that the heat transfer process on superhydrophobic surfaces is independent of the trapped gas. Instead, we find that, for a given spreading factor, the small fraction of heat transferred is controlled by two dimensionless groupings of physical parameters: one that relates the thermal properties of the drop and bulk substrate and the other that characterizes the relative thermal, inertial, and capillary dynamics of the drop.

  3. Electric generation and ratcheted transport of contact-charged drops

    Science.gov (United States)

    Cartier, Charles A.; Graybill, Jason R.; Bishop, Kyle J. M.

    2017-10-01

    We describe a simple microfluidic system that enables the steady generation and efficient transport of aqueous drops using only a constant voltage input. Drop generation is achieved through an electrohydrodynamic dripping mechanism by which conductive drops grow and detach from a grounded nozzle in response to an electric field. The now-charged drops are transported down a ratcheted channel by contact charge electrophoresis powered by the same voltage input used for drop generation. We investigate how the drop size, generation frequency, and transport velocity depend on system parameters such as the liquid viscosity, interfacial tension, applied voltage, and channel dimensions. The observed trends are well explained by a series of scaling analyses that provide insight into the dominant physical mechanisms underlying drop generation and ratcheted transport. We identify the conditions necessary for achieving reliable operation and discuss the various modes of failure that can arise when these conditions are violated. Our results demonstrate that simple electric inputs can power increasingly complex droplet operations with potential opportunities for inexpensive and portable microfluidic systems.

  4. Measurement of an Evaporating Drop on a Reflective Substrate

    Science.gov (United States)

    Chao, David F.; Zhang, Nengli

    2004-01-01

    A figure depicts an apparatus that simultaneously records magnified ordinary top-view video images and laser shadowgraph video images of a sessile drop on a flat, horizontal substrate that can be opaque or translucent and is at least partially specularly reflective. The diameter, contact angle, and rate of evaporation of the drop as functions of time can be calculated from the apparent diameters of the drop in sequences of the images acquired at known time intervals, and the shadowgrams that contain flow patterns indicative of thermocapillary convection (if any) within the drop. These time-dependent parameters and flow patterns are important for understanding the physical processes involved in the spreading and evaporation of drops. The apparatus includes a source of white light and a laser (both omitted from the figure), which are used to form the ordinary image and the shadowgram, respectively. Charge-coupled-device (CCD) camera 1 (with zoom) acquires the ordinary video images, while CCD camera 2 acquires the shadowgrams. With respect to the portion of laser light specularly reflected from the substrate, the drop acts as a plano-convex lens, focusing the laser beam to a shadowgram on the projection screen in front of CCD camera 2. The equations for calculating the diameter, contact angle, and rate of evaporation of the drop are readily derived on the basis of Snell s law of refraction and the geometry of the optics.

  5. Joint Advisory Appeals Board report

    CERN Document Server

    Lalande, Amanda

    2018-01-01

    With regard to the internal appeal procedure, Article R VI 1.18 of the Staff Rules and Regulations states that unless the member of the personnel objects, (the) decision and report of the JAAB (Joint Advisory Appeals Board) shall be brought to the attention of the members of the personnel.

  6. The importance of board independence

    NARCIS (Netherlands)

    Zijl, N.J.M.

    2012-01-01

    Although the attributed importance of board independence is high, a clear definition of independence does not exist. Furthermore, the aim and consequences of independence are the subject of discussion and empirical evidence about the impact of independence is weak and disputable. Despite this lack

  7. The Audit Committee. Board Basics

    Science.gov (United States)

    Ostrom, John S.

    2004-01-01

    The Effective Committees set of booklets comprises publications on the following committees: investment, buildings and grounds, academic affairs, student affairs, finance, development, trustees, audit, compensation, and executive. It is part of the AGB Board Basics Series. This report describes the primary role of an audit committee. The primary…

  8. School Board Ethics and Effectiveness

    Science.gov (United States)

    Feuerstein, Abe

    2009-01-01

    Since the early 1980s, educational policy has increasingly been focused on improving student performance (Conley, 2003, Murphy, 1990). School governance in general, and school boards in particular, have often been viewed as either the means of implementing needed reforms or as roadblocks in their way (Boyd, 2003; Delagardelle, M.; 2008; Howell,…

  9. Theoretical Exploration of Barrel-Shaped Drops on Cactus Spines.

    Science.gov (United States)

    Luo, Cheng

    2015-11-03

    To survive an arid environment, desert cacti are capable of harvesting water from fog by transporting condensed water drops using their spines. Cactus spines have a conical shape. In this work, on the basis of the difference of liquid pressure, a new theoretical model has been developed for a barrel-shaped liquid drop on a conical wire. This model is further simplified to interpret the effects of contact angles, conical angle, surface microgrooves, and gravity on the drop movement along a cactus spine.

  10. Ultrasonic defect sizing using decibel drop methods. III

    International Nuclear Information System (INIS)

    Mills, C.; Goszczynski, J.; Mitchell, A.B.

    1988-03-01

    An earlier study on the use of ultrasonic decibel drop sizing methods for determining the length and vertical extent of flaws in welded steel sections was based on the scanning of machined flaws and fabrication flaws. The present study utilized the techniques developed to perform a similar study of the type of flaws expected to develop during service (e.g. fatigue cracks). The general findings are that: a) the use of decibel drops of less than 14 dB generally undersize the length of fatigue cracks; and b) the use of decibel drop methods to determine vertical extent is questionable

  11. Numerical simulation of the drop spreading on a horizontal plane

    Science.gov (United States)

    Zyuzina, N. A.; Ostapenko, V. V.

    2017-10-01

    A shallow water model of film flow is used to describe the process of a drop spreading on a horizontal plane, taking into account the liquid viscosity, heat-mass transfer and surface tension forces. To simulate this flow numerically in polar coordinates an unconditionally stable implicit difference scheme has been developed, which (in the case of evaporation) can calculate the drop spreading over a dry surface without special allocation of the drop boundary. A region of dimensionless parameters is singled out under which the evaporating droplet, as a result of surface tension forces, transforms into a circular ring before complete evaporation.

  12. Ready-made allogeneic ABO-specific serum eye drops

    DEFF Research Database (Denmark)

    Harritshøj, Lene Holm; Nielsen, Connie; Ullum, Henrik

    2014-01-01

    PURPOSE: To overcome problems and delays of the preparation of autologous serum eye drops, a production line of ABO-specific allogeneic serum eye drops from male blood donors was set up in a blood bank. Feasibility, clinical routine, safety and efficacy were evaluated in a cohort of patients...... serum treatment. CONCLUSION: Ready-made ABO-identical allogeneic serum eye drops were straightforwardly produced, quality-assured and registered as a safe standard blood product for the treatment of certain cases of severe dry eye disease. Therapeutic efficacy was comparable to previous reports...

  13. DOE's Environmental Management Site-Specific Advisory Board: The Roles, Work, and Assessment of the Constituent Local Boards - 13587

    Energy Technology Data Exchange (ETDEWEB)

    Alexander, Catherine [U.S. Dept. of Energy, Office of Environmental Management, Office of Intergovernmental and Community Activities, 1000 Independence Avenue, S.W.,Washington, D.C. 20585 (United States); Freeman, Jenny [Strata-G, LLC, 2027 Castaic Lane, Knoxville, TN 37932 (United States); Cantrell, Yvette [Restoration Services, Inc., 136 Mitchell Road, Oak Ridge, TN 37830 (United States)

    2013-07-01

    The charter for the Department of Energy's Environmental Management (EM) Site-Specific Advisory Board (SSAB) was approved under the Federal Advisory Committee Act (FACA) in 1994. With a unique mandate to provide public input on issues associated with the cleanup of nuclear legacy sites in the U.S., the EM SSAB comprises eight local boards, which are based at major EM sites. While each board is unique to the community in which it is located and reflects the diversity of the local population, the boards are governed by FACA, related regulations, and DOE policies that are intended to standardize agency advisory board operations. The EM SSAB local boards are made up of a diverse group of citizens who want to understand the mission and goals of the EM program and to help EM achieve those goals for the benefit of their communities. Some are quite passionate about their mission; others need to be coaxed into active participation. Maintaining productive relationships and a supportive environment for effective board operations is the challenge of board management for DOE EM and the board members themselves. DOE draws on research findings and best practices literature from academics and practitioners in the field of public involvement in its board management practices. The EM SSAB is also evaluated annually under the law to ensure that the investment of taxpayer dollars in the board is warranted in light of the contributions of the board. Further evaluation takes place at the agency and site levels in order to identify what aspects of board functioning the agency and board members find important to its success and to address areas where improvement is needed. Board contributions, compliance factors, and measurable outcomes related to board products and process areas are key to agency commitment to ongoing support of the boards and to participant satisfaction and thus continued member involvement. In addition to evaluation of these factors in improving board

  14. Method and apparatus for producing drops using a drop-on-demand dispenser

    Science.gov (United States)

    Chen, Alvin U.; Basaran, Osman A.

    2003-01-01

    A method and apparatus for dispensing fluid from a drop-on-demand (DOD) fluid dispenser. The method involves withdrawing fluid in the dispenser for a first duration of time, followed by a second duration of time during which the fluid is propelled toward the orifice of the dispenser. Following the period during which the fluid is propelled, there is a second withdrawing of the fluid into the dispenser. The duration of the propelling period is shorter than the duration of either the first withdrawing or the second withdrawing. The propelling of the fluid results in the extension of a small tongue of fluid from the meniscus of the fluid. The second withdrawing of the fluid results in a retraction of the meniscus into the passageway such that only the small tongue of fluid separates and is ejected from the dispenser.

  15. Handling test of eye drop dispenser--comparison of unit-dose pipettes with conventional eye drop bottles.

    Science.gov (United States)

    Parkkari, Minna; Latvala, Terho; Ropo, Auli

    2010-06-01

    The aims of this study were to investigate how elderly people handle single-use eye drop dispensers (unit-dose pipettes) and to compare the performance with conventional eye drop bottles. In this open-label study, the handling of unit-dose pipettes and conventional eye drop bottles was compared in 41 elderly people who had little or no prior regular use of eye drop dispensers. The participants tested both types of dispenser once, and the following 7 variables were studied: ease/difficulty of opening the dispenser; influence of the size for handling of the dispenser; influence of the shape for handling of the dispenser; observation of the contents in the dispenser; the feeling of the dispenser in the hand; ease/difficulty of drop instillation on the eye from the dispenser; and overall performance of the eye drop dispenser. The dispensers contained isotonic saline, and a visual analog scale was used for assessment of each of the above variables. The mean age of the participants was 73 years. A statistically significant difference in favor of the unit-dose pipettes was found with respect to observation of the contents in the dispenser, ease of administration, and the overall performance. Women regarded the unit-dose pipettes generally better than the bottles, but such a difference was not seen in men. The study participants managed the unit-dose pipettes at least as well as the conventional eye drop bottles. If anything, the unit-dose pipettes appeared to be easier to use.

  16. Structural performance of an IP2 package in free drop test conditions: Numerical and experimental evaluations

    International Nuclear Information System (INIS)

    Lo Frano, Rosa; Pugliese, Giovanni; Nasta, Marco

    2014-01-01

    Highlights: • Vertical free drop test. • Qualification of an IP2 type Italian packaging. • Numerical and experimental investigation of the package integrity. • Demonstration the Italian packaging meets safety requirements. - Abstract: The casks or packaging systems used for the transportation of nuclear materials, especially spent fuel elements, have to be designed according to rigorous acceptance requirements, like the IAEA ones, in order to provide protection to human beings and environment against radiation exposure and contamination. This study deals with the free drop test of an Italian design packaging system to be used for the transportation of low and intermediate level radioactive wastes. Impact drop experiments were performed in the Lab. Scalbatraio of the DICI – University of Pisa. Dynamic analyses too have been carried out, by refined models of both the cask and target surface to predict the effects of the impact shock (vertical drop) on the package. The experimental tests and numerical analyses are thoroughly compared, presented and discussed. The numerical approach shows to be suitable to reproduce with good reliability the test situations and results

  17. Limiting the Accidental Pressure Drop in NIF Beam Tubes

    International Nuclear Information System (INIS)

    Garcia, M

    2000-01-01

    This report summarizes the use of a one-dimensional model of a time-dependent compressible flow condition to validate the results from a more sophisticated three-dimensional model. The flow conditions consist of the sudden decompression of a pressurized tube joined to an evacuated sphere, where the tube also has a leak to external atmosphere that is triggered open at a given pressure difference below sea-level pressure. This flow model is used to calculate conditions in a NIF beam tube if an internal vacuum barrier fails, and to calculate how the size and timing of an opening to external atmosphere changes tube pressure. Decompression of a NIF beam tube is a potential safety hazard since the tube could collapse if the tube pressure is reduced below the buckling limit. To prevent this from occurring, each pressurized section includes a rupture panel which is designed to open to external atmosphere at a given pressure difference. The inrush of external atmosphere through the rupture panel fills both the tube and the vacuum drawing on it, and in this way the pressure drop in the tube is quickly limited and reversed. In summary, the results from the 1D model indicate that the 3-D calculations are accurate and reasonable

  18. Bird nesting and droppings control on highway structures.

    Science.gov (United States)

    2010-10-01

    This report provides a comprehensive literature survey of permanent and temporary deterrents to nesting and roosting, a : discussion of risks to human health and safety from exposure to bird nests and droppings and recommended protective measures, : ...

  19. Modeling gas kinetic effects in drop collision and impact

    Science.gov (United States)

    Chubynsky, Mykyta V.; Belousov, Kirill I.; Lockerby, Duncan A.; Sprittles, James E.

    2017-11-01

    When liquid drops collide with each other (collision) or with a solid surface (impact), the thickness of the intervening gas film (which, in particular, gives rise to bouncing off wettable surfaces) is often comparable to the mean free path of the gas molecules and thus gas kinetic effects are significant. We study drop collision and impact computationally using an interface-tracking finite element approach. The gas film is treated in the lubrication approximation. Gas kinetic effects are taken into account by introducing factors (functions of the Knudsen number) modifying the gas flow rate and shear stress. Our results for drop collision are in excellent agreement with those of Li who modeled the gas using the full Navier-Stokes equations with an effective viscosity. For impact, where Li's approach cannot be used, we obtain good agreement with drop bouncing experiments. We acknowledge the support of the Leverhulme Trust and the EPSRC (EP/N016602/1).

  20. Analysis of driver merging behavior at lane drops on freeways.

    Science.gov (United States)

    2013-12-01

    Lane changing assistance systems advise drivers on safe gaps for making mandatory lane changes at lane drops. In this : study, such a system was developed using a Bayes classifier and a decision tree to model lane changes. Detailed vehicle : trajecto...

  1. Bubble formation during drop impact on a heated pool

    Science.gov (United States)

    Tian, Yuansi; Alhazmi, Muath; Kouraytem, Nadia; Thoroddsen, Sigurdur

    2017-11-01

    Ultra high-speed video imaging, at up to 200 kfps, is used to investigate a drop impinging onto a high temperature pool. The room-temperature perfluorohexane drop, which has a boiling temperature as low as 56 °C impacts on the soybean oil pool heated up to around 200 °C, which is overwhelmingly higher than the boiling temperature of the drop. The bottom of the drop is therefore covered by a layer of vapor which prevents contact between the two immiscible liquid surfaces, akin to the Leidenfrost effect However, as the pool temperature is reduced, one starts seeing contact and the dynamics transition into the vapor explosion regime. At the boundary of this regime we observe some entrapment of scattered or a toroidal ring of small bubbles. Experimental video data will be presented to show this novel phenomenon and explain how these bubbles are formed and evolve.

  2. Herpes,zoster with Wrist Drop and Aberrant Lesions

    Directory of Open Access Journals (Sweden)

    R K Dutta

    1987-01-01

    Full Text Available A patient having herpes zoster involving C6, 7, 8, Dl and 2 segments, developed ipsilateral wrist drop and aberrant lesions. Paralytic deformity preceded the skin eruption by one day.

  3. Non-isothermal spreading of liquid drops on horizontal plates

    International Nuclear Information System (INIS)

    Ehrhard, P.; Davis, S.H.

    1990-05-01

    A viscous-liquid drop spreads on a smooth horizontal surface, which is uniformly heated or cooled. Lubrication theory is used to study thin drops subject to capillary, thermocapillary and gravity forces, and a variety of contact-angle-versus-speed conditions. It is found for isothermal drops that gravity is very important at large times and determines the power law for unlimited spreading. Predictions compare well with the experimental data on isothermal spreading for both two-dimensional and axisymmetric configurations. It is found that heating (cooling) retards (augments) the spreading process. When the advancing contact angle is zero, heating will cause the drop to spread only finitely far. For positive advancing contact angles, sufficient cooling will cause unlimited spreading. Thus, the heat transfer serves as a sentitive control on the spreading. (orig.) [de

  4. Origin and dynamics of vortex rings in drop splashing.

    Science.gov (United States)

    Lee, Ji San; Park, Su Ji; Lee, Jun Ho; Weon, Byung Mook; Fezzaa, Kamel; Je, Jung Ho

    2015-09-04

    A vortex is a flow phenomenon that is very commonly observed in nature. More than a century, a vortex ring that forms during drop splashing has caught the attention of many scientists due to its importance in understanding fluid mixing and mass transport processes. However, the origin of the vortices and their dynamics remain unclear, mostly due to the lack of appropriate visualization methods. Here, with ultrafast X-ray phase-contrast imaging, we show that the formation of vortex rings originates from the energy transfer by capillary waves generated at the moment of the drop impact. Interestingly, we find a row of vortex rings along the drop wall, as demonstrated by a phase diagram established here, with different power-law dependencies of the angular velocities on the Reynolds number. These results provide important insight that allows understanding and modelling any type of vortex rings in nature, beyond just vortex rings during drop splashing.

  5. Modeling merging behavior at lane drops : [tech transfer summary].

    Science.gov (United States)

    2015-02-01

    A better understanding of the merging behavior of drivers will lead : to the development of better lane-drop traffic-control plans and : strategies, which will provide better guidance to drivers for safer : merging.

  6. Self-excited hydrothermal waves in evaporating sessile drops

    Science.gov (United States)

    Sefiane, K.; Moffat, J. R.; Matar, O. K.; Craster, R. V.

    2008-08-01

    Pattern formation driven by the spontaneous evaporation of sessile drops of methanol, ethanol, and FC-72 using infrared thermography is observed and, in certain cases, interpreted in terms of hydrothermal waves. Both methanol and ethanol drops exhibit thermal wave trains, whose wave number depends strongly on the liquid volatililty and substrate thermal conductivity. The FC-72 drops develop cellular structures whose size is proportional to the local thickness. Prior to this work, hydrothermal waves have been observed in the absence of evaporation in shallow liquid layers subjected to an imposed temperature gradient. In contrast, here both the temperature gradients and the drop thickness vary spatially and temporally and are a natural consequence of the evaporation process.

  7. 14 CFR 27.725 - Limit drop test.

    Science.gov (United States)

    2010-01-01

    ... under impact of the tire (at the proper inflation pressure) plus the vertical component of the axle..., during impact, on the mass used in the drop test (i.e., the acceleration dv/dt in g's recorded in the...

  8. Drop performance test and evaluation for HANARO shutoff units

    International Nuclear Information System (INIS)

    Jung, Y. H.; Cho, Y. K.; Lee, J. H.; Choi, Y. S.; Woo, J. S.

    2004-01-01

    The function of the shutoff units of the HANARO is to rapidly insert the shutoff rod into the reactor core for safe shutdown of reactor. This paper describes drop performance test and evaluation for a shutoff unit for the technical verification of lifetime extension and localization of the HANARO shutoff units. We have performed preliminary drop performance tests for a shutoff unit at 1/2-core test loop and analyzed through the comparison with the test results performed during design verification test and the results of the periodic performance test in HANARO. It shows that the results of the local fabrication, installation and alignment for the shutoff unit meet the basic performance requirements, Furthermore, the performance evaluation method of the periodic drop test of the HANARO shutoff units is a conservative method comparing with the real drop time

  9. Rotavirus and the Vaccine (Drops) to Prevent It

    Science.gov (United States)

    ... and Teen Vaccine Resources Related Links Vaccines & Immunizations Rotavirus and the Vaccine (Drops) to Prevent It Language: ... the vaccine. Why should my child get the rotavirus vaccine? The rotavirus vaccine: Protects your child from ...

  10. Satellite Formation during Coalescence of Unequal Size Drops

    KAUST Repository

    Zhang, F. H.

    2009-03-12

    The coalescence of a drop with a flat liquid surface pinches off a satellite from its top, in the well-known coalescence cascade, whereas the coalescence of two equally sized drops does not appear to leave such a satellite. Herein we perform experiments to identify the critical diameter ratio of two drops, above which a satellite is produced during their coalescence. We find that the critical parent ratio is as small as 1.55, but grows monotonically with the Ohnesorge number. The daughter size is typically about 50% of the mother drop. However, we have identified novel pinch-off dynamics close to the critical size ratio, where the satellite does not fully separate, but rather goes directly into a second stage of the coalescence cascade, thus generating a much smaller satellite droplet.

  11. Dropped fuel damage prediction techniques and the DROPFU code

    International Nuclear Information System (INIS)

    Mottershead, K.J.; Beardsmore, D.W.; Money, G.

    1995-01-01

    During refuelling, and fuel handling, at UK Advanced Gas Cooled Reactor (AGR) stations it is recognised that the accidental dropping of fuel is a possibility. This can result in dropping individual fuel elements, a complete fuel stringer, or a whole assembly. The techniques for assessing potential damage have been developed over a number of years. This paper describes how damage prediction techniques have subsequently evolved to meet changing needs. These have been due to later fuel designs and the need to consider drops in facilities outside the reactor. The paper begins by briefly describing AGR fuel and possible dropped fuel scenarios. This is followed by a brief summary of the damage mechanisms and the assessment procedure as it was first developed. The paper then describes the additional test work carried out, followed by the detailed numerical modelling. Finally, the paper describes the extensions to the practical assessment methods. (author)

  12. Ocular penetration and pharmacokinetics of topical clarithromycin eye drops to rabbits.

    Science.gov (United States)

    Zhang, Junjie; Wang, Liya; Zhou, Jing; Zhang, Li; Xia, Huiyun; Zhou, Tianyang; Zhang, Hongmin

    2014-02-01

    To evaluate the ocular pharmacokinetics of clarithromycin (CLA) eye drops topically applied to the corneas of rabbits. One 50-μL drop of CLA (0.25%) was administered to each New Zealand white rabbit in a single dose group, and one 50-μL drop of CLA was administered 6 times at 5-min intervals to each rabbit in a loading dose group. The effect of debridement on corneal penetration was also investigated in a de-epithelium group. The drug concentrations in the cornea and aqueous humor (AH) were assayed using high-performance liquid chromatography with tandem mass spectrometry (HPLC-MS/MS) analysis. Maximum CLA levels were achieved in the corneas and AH at 15 and 60 min, respectively, in the intact epithelium eyes in the single dose group (24.54±10.64 μg/g and 0.78±0.22 μg/mL, respectively, mean±the standard error of the mean, n=8). In the loading dose group, 30 min after the last application, the CLA level in the corneas reached 92.26±17.62 μg/g. In the loading dose group, the drug levels in the corneas and AH were significantly increased compared with the drug levels in the corneas with the intact epithelium and de-epithelium eyes in the single dose group at the corresponding time points (Pcorneas and AH for the intact eyes were 103.28 and 132.61 min, respectively. Therapeutic CLA levels can be achieved in rabbit corneas after topically applying the drug with eye drops.

  13. Scientific Advisory Board FY92 Annual Report.

    Science.gov (United States)

    1993-03-01

    Implementation Board for the North American Waterfowl Management Plan; Chairman, Chief of Engineers’ Environmental Advisory Board. Awards: Aldo ... Leopold Medal, Wildlife Society; Barbara Swain Medal, Natural Resources Council of America. Authored numerous papers and reports, assisted editing and

  14. Sustainability issues in circuit board recycling

    DEFF Research Database (Denmark)

    Legarth, Jens Brøbech; Alting, Leo; Baldo, Gian Luca

    1995-01-01

    The resource recovery and environmental impact issues of printed circuit board recycling by secondary copper smelters are discussed. Guidelines concerning material selection for circuit board manufacture and concerning the recycling processes are given to enhance recovery efficiency and to lower...

  15. 75 FR 67351 - Environmental Management Advisory Board

    Science.gov (United States)

    2010-11-02

    ... Environmental Management Advisory Board AGENCY: Department of Energy. ACTION: Notice of Open Teleconference. SUMMARY: This notice announces a teleconference of the Environmental Management Advisory Board (EMAB). The... is to provide the Assistant Secretary for Environmental Management (EM) with advice and...

  16. Nectar and pollination drops: how different are they?

    Science.gov (United States)

    Nepi, Massimo; von Aderkas, Patrick; Wagner, Rebecca; Mugnaini, Serena; Coulter, Andrea; Pacini, Ettore

    2009-08-01

    Pollination drops and nectars (floral nectars) are secretions related to plant reproduction. The pollination drop is the landing site for the majority of gymnosperm pollen, whereas nectar of angiosperm flowers represents a common nutritional resource for a large variety of pollinators. Extrafloral nectars also are known from all vascular plants, although among the gymnosperms they are restricted to the Gnetales. Extrafloral nectars are not generally involved in reproduction but serve as 'reward' for ants defending plants against herbivores (indirect defence). Although very different in their task, nectars and pollination drops share some features, e.g. basic chemical composition and eventual consumption by animals. This has led some authors to call these secretions collectively nectar. Modern techniques that permit chemical analysis and protein characterization have very recently added important information about these sugary secretions that appear to be much more than a 'reward' for pollinating (floral nectar) and defending animals (extrafloral nectar) or a landing site for pollen (pollination drop). Nectar and pollination drops contain sugars as the main components, but the total concentration and the relative proportions are different. They also contain amino acids, of which proline is frequently the most abundant. Proteomic studies have revealed the presence of common functional classes of proteins such as invertases and defence-related proteins in nectar (floral and extrafloral) and pollination drops. Invertases allow for dynamic rearrangement of sugar composition following secretion. Defence-related proteins provide protection from invasion by fungi and bacteria. Currently, only few species have been studied in any depth. The chemical composition of the pollination drop must be investigated in a larger number of species if eventual phylogenetic relationships are to be revealed. Much more information can be provided from further proteomic studies of both

  17. Liquid-gas mass transfer at drop structures

    DEFF Research Database (Denmark)

    Matias, Natércia; Nielsen, Asbjørn Haaning; Vollertsen, Jes

    2017-01-01

    established. Then, by applying the two-film theory with two-reference substances, the relation to hydrogen sulfide release was defined. The experiments confirmed that the choice of the type of drop structure is critical to determine the uptake/emission rates. By quantifying the air-water mass transfer rates...... between free-fall and backdrop types of drop, the latter resulted in considerably lower oxygen uptake rates....

  18. Refrigeration. Two-Phase Flow. Flow Regimes and Pressure Drop

    DEFF Research Database (Denmark)

    Knudsen, Hans-Jørgen Høgaard

    2002-01-01

    The note gives the basic definitions used in two-phase flow. Flow regimes and flow regimes map are introduced. The different contributions to the pressure drop are stated together with an imperical correlation from the litterature.......The note gives the basic definitions used in two-phase flow. Flow regimes and flow regimes map are introduced. The different contributions to the pressure drop are stated together with an imperical correlation from the litterature....

  19. Air-drop blood supply in the French Army.

    Science.gov (United States)

    Javaudin, Olivier; Baillon, A; Varin, N; Martinaud, C; Pouget, T; Civadier, C; Clavier, B; Sailliol, A

    2018-02-12

    Haemorrhagic shock remains the leading cause of preventable death in overseas and austere settings. Transfusion of blood components is critical in the management of this kind of injury. For French naval and ground military units, this supply often takes too long considering the short shelf-life of red blood cell concentrates (RBCs) and the limited duration of transport in cooling containers (five to six days). Air-drop supply could be an alternative to overcome these difficulties on the condition that air-drop does not cause damage to blood units. After a period of study and technical development of packaging, four air-drops at medium and high altitudes were performed with an aircraft of the French Air Force. After this, one air-drop was carried out at medium altitude with 10 RBCs and 10 French lyophilised plasma (FLYP). A second air-drop was performed with a soldier carrying one FLYP unit at 12 000 feet. For these air-drops real blood products were used, and quality control testing and temperature monitoring were performed. The temperatures inside the containers were within the normal ranges. Visual inspection indicated that transfusion packaging and dumped products did not undergo deterioration. The quality control data on RBCs and FLYP, including haemostasis, suggested no difference before and after air-drop. The operational implementation of the air-drop of blood products seems to be one of the solutions for the supply of blood products in military austere settings or far forward on battlefield, allowing safe and early transfusion. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  20. Active structuring of colloidal armour on liquid drops

    OpenAIRE

    Dommersnes, Paul; Rozynek, Zbigniew; Mikkelsen, Alexander; Castberg, Rene; Kjerstad, Knut; Hersvik, Kjetil; Fossum, Jon Otto

    2013-01-01

    Adsorption and assembly of colloidal particles at the surface of liquid droplets are at the base of particle-stabilized emulsions and templating. Here we report that electrohydrodynamic and electro-rheological effects in leaky-dielectric liquid drops can be used to structure and dynamically control colloidal particle assemblies at drop surfaces, including electric-fieldassisted convective assembly of jammed colloidal ‘ribbons’, electro-rheological colloidal chains confined to a...

  1. Investigating Call Drops with Field Measurements on Commercial Mobile Phones

    DEFF Research Database (Denmark)

    Messina, Alessandro; Caragea, Gabriel; Compta, Pol Torres

    2013-01-01

    can be done per day. In this paper we present a new methodology to investigate call drops by using mobile phones to do the measurements following the concept of citizen sensing. Therefore, a mobile application for Android is made that collects all necessary data and dumps the measurement results...... mobile phone and network. This low cost variant of field testing is developed for call drops but could be used for any other parameter of interest....

  2. The Effects of Drop Height and Padding Surface on Bruising of Exportable Apple

    Directory of Open Access Journals (Sweden)

    D Ghanbarian

    2015-03-01

    Full Text Available Unfortunately despite the great ranking of Iran for apple production around the world, the export potential is not suitable. It seems that one of the major causes of poor quality for Iranian apple varieties is bruising damage of this product. Therefore, in this study, some factors affecting the apple bruising were addressed. For this purpose, factorial experiment in a completely randomized design with 72 treatments, including variety factor in three levels (Golden Delicious, Red Delicious and Granny Smith, type of padding surface in four levels (Cardboard on plastic, wood, Rubber on steel and apple and the drop height in six levels (5, 15, 25, 35, 45 and 55 cm with four replications were considered. Moreover, the maximum allowable drop heights of apples along with bruising volume estimation models were studied. Analysis of variance (ANOVA showed that bruising area and volume were significantly affected by all experimental parameters at the 1% level. The comparison test revealed that Granny Smith has tougher tissues and is less prone to vulnerability. Based on the results of this study, the maximum allowable drop heights for the Red Delicious, Golden Delicious and Granny Smith varieties were found to be 12, 15 and 20 cm, respectively. In addition, the effect of apple variety on the dependent parameters was significant. Based on the findings of this study, the bruising due to the impact of apple and apple was lower for the moving apples compared with the stationary apples.

  3. Lubrication model for evaporation of binary sessile drops

    Science.gov (United States)

    Williams, Adam; Sáenz, Pedro; Karapetsas, George; Matar, Omar; Sefiane, Khellil; Valluri, Prashant

    2017-11-01

    Evaporation of a binary mixture sessile drop from a solid substrate is a highly dynamic and complex process with flow driven both thermal and solutal Marangoni stresses. Experiments on ethanol/water drops have identified chaotic regimes on both the surface and interior of the droplet, while mixture composition has also been seen to govern drop wettability. Using a lubrication-type approach, we present a finite element model for the evaporation of an axisymmetric binary drop deposited on a heated substrate. We consider a thin drop with a moving contact line, taking also into account the commonly ignored effects of inertia which drives interfacial instability. We derive evolution equations for the film height, the temperature and the concentration field considering that the mixture comprises two ideally mixed volatile components with a surface tension linearly dependent on both temperature and concentration. The properties of the mixture such as viscosity also vary locally with concentration. We explore the parameter space to examine the resultant effects on wetting and evaporation where we find qualitative agreement with experiments in both these areas. This enables us to understand the nature of the instabilities that spontaneously emerge over the drop lifetime. EPSRC - EP/K00963X/1.

  4. Microwave dielectric heating of drops in microfluidic devices.

    Science.gov (United States)

    Issadore, David; Humphry, Katherine J; Brown, Keith A; Sandberg, Lori; Weitz, David A; Westervelt, Robert M

    2009-06-21

    We present a technique to locally and rapidly heat water drops in microfluidic devices with microwave dielectric heating. Water absorbs microwave power more efficiently than polymers, glass, and oils due to its permanent molecular dipole moment that has large dielectric loss at GHz frequencies. The relevant heat capacity of the system is a single thermally isolated picolitre-scale drop of water, enabling very fast thermal cycling. We demonstrate microwave dielectric heating in a microfluidic device that integrates a flow-focusing drop maker, drop splitters, and metal electrodes to locally deliver microwave power from an inexpensive, commercially available 3.0 GHz source and amplifier. The temperature change of the drops is measured by observing the temperature dependent fluorescence intensity of cadmium selenide nanocrystals suspended in the water drops. We demonstrate characteristic heating times as short as 15 ms to steady-state temperature changes as large as 30 degrees C above the base temperature of the microfluidic device. Many common biological and chemical applications require rapid and local control of temperature and can benefit from this new technique.

  5. Vortex-ring-induced large bubble entrainment during drop impact

    KAUST Repository

    Thoraval, Marie-Jean

    2016-03-29

    For a limited set of impact conditions, a drop impacting onto a pool can entrap an air bubble as large as its own size. The subsequent rise and rupture of this large bubble plays an important role in aerosol formation and gas transport at the air-sea interface. The large bubble is formed when the impact crater closes up near the pool surface and is known to occur only for drops that are prolate at impact. Herein we use experiments and numerical simulations to show that a concentrated vortex ring, produced in the neck between the drop and the pool, controls the crater deformations and pinchoff. However, it is not the strongest vortex rings that are responsible for the large bubbles, as they interact too strongly with the pool surface and self-destruct. Rather, it is somewhat weaker vortices that can deform the deeper craters, which manage to pinch off the large bubbles. These observations also explain why the strongest and most penetrating vortex rings emerging from drop impacts are not produced by oblate drops but by more prolate drop shapes, as had been observed in previous experiments.

  6. Drop detachment and motion on fuel cell electrode materials.

    Science.gov (United States)

    Gauthier, Eric; Hellstern, Thomas; Kevrekidis, Ioannis G; Benziger, Jay

    2012-02-01

    Liquid water is pushed through flow channels of fuel cells, where one surface is a porous carbon electrode made up of carbon fibers. Water drops grow on the fibrous carbon surface in the gas flow channel. The drops adhere to the superficial fiber surfaces but exhibit little penetration into the voids between the fibers. The fibrous surfaces are hydrophobic, but there is a substantial threshold force necessary to initiate water drop motion. Once the water drops begin to move, however, the adhesive force decreases and drops move with minimal friction, similar to motion on superhydrophobic materials. We report here studies of water wetting and water drop motion on typical porous carbon materials (carbon paper and carbon cloth) employed in fuel cells. The static coefficient of friction on these textured surfaces is comparable to that for smooth Teflon. But the dynamic coefficient of friction is several orders of magnitude smaller on the textured surfaces than on smooth Teflon. Carbon cloth displays a much smaller static contact angle hysteresis than carbon paper due to its two-scale roughness. The dynamic contact angle hysteresis for carbon paper is greatly reduced compared to the static contact angle hysteresis. Enhanced dynamic hydrophobicity is suggested to result from the extent to which a dynamic contact line can track topological heterogeneities of the liquid/solid interface.

  7. Capillary-Inertial Colloidal Catapult upon Drop Coalescence

    Science.gov (United States)

    Chavez, Roger; Liu, Fangjie; Feng, James; Chen, Chuan-Hua

    2014-11-01

    To discharge micron-sized particles such as colloidal contaminants and biological spores, an enormous power density is needed to compete against the strong adhesive forces between the small particles and the supporting surface as well as the significant air friction exerted on the particles. Here, we demonstrate a colloidal catapult that achieves such a high power density by extracting surface energy released upon drop coalescence within an extremely short time period, which is governed by the capillary-inertial process converting the released surface energy into the bulk inertia of the merged drop. When two drops coalesce on top of a spherical particle, the resulting capillary-inertial oscillation is perturbed by the solid particle, giving rise to a net momentum eventually propelling the particle to launch from the supporting surface. The measured launching velocity follows a scaling law that accounts for the redistribution of the momentum of the merged drop onto the particle-drop complex, and is therefore proportional to the capillary-inertial velocity characterizing the coalescing drops. The interfacial flow process associated with the colloidal catapult is elucidated with both high-speed imaging and phase-field simulations.

  8. Short Duration Reduced Gravity Drop Tower Design and Development

    Science.gov (United States)

    Osborne, B.; Welch, C.

    The industrial and commercial development of space-related activities is intimately linked to the ability to conduct reduced gravity research. Reduced gravity experimentation is important to many diverse fields of research in the understanding of fundamental and applied aspects of physical phenomena. Both terrestrial and extra-terrestrial experimental facilities are currently available to allow researchers access to reduced gravity environments. This paper discusses two drop tower designs, a 2.0 second facility built in Australia and a proposed 2.2 second facility in the United Kingdom. Both drop towers utilise a drag shield for isolating the falling experiment from the drag forces of the air during the test. The design and development of The University of Queensland's (Australia) 2.0 second drop tower, including its specifications and operational procedures is discussed first. Sensitive aspects of the design process are examined. Future plans are then presented for a new short duration (2.2 sec) ground-based reduced gravity drop tower. The new drop tower has been designed for Kingston University (United Kingdom) to support teaching and research in the field of reduced gravity physics. The design has been informed by the previous UQ drop tower design process and utilises a catapult mechanism to increase test time and also incorporates features to allow participants for a variety of backgrounds (from high school students through to university researchers) to learn and experiment in reduced gravity. Operational performance expectations for this new facility are also discussed.

  9. Ultrasonic defect-sizing using decibel drop methods. I

    International Nuclear Information System (INIS)

    Murphy, R.V.

    1987-03-01

    Results are reported of a study performed to investigate the accuracy and repeatability of various ultrasonic decibel (dB) drop sizing methods in determining the length, vertical extent and orientation of artificial and real weld flaws in thin steel sections. Seven artificial flaws and nine real weld flaws were examined; over 200 data plots were produced. The general findings are: a) length and vertical extent are assessed most accurately when using a 14 dB drop from the maximum indication amplitude; b) decibel drops less that 14 dB generally undersize flaws while decibel drops greater than 14 dB generally oversize flaws; c) flaws which are smaller than the width of the sound beam cannot be assessed accurately using dB drop methods; d) large flaws are assessed most accurately when the sound beam strikes the flaws at near normal incidence; e) the vertical extent and orientation of large flaws are plotted most accurately using the beam centre line method as opposed to the beam profile method; and, f) the limitations of dB-drop-sizing methods have considerable ramifications for CAN3-N285.4-M83 and ASME XI evaluation criteria

  10. Distinguishing between microscale gaseous bubbles and liquid drops

    Science.gov (United States)

    Tan, Beng Hau; An, Hongjie; Chan, Chon U.; Ohl, Claus-Dieter

    2015-11-01

    In recent years, there has been strong research interest in decorating surfaces with tiny bubbles and drops due to their potential applications in reducing slippage in micro and nanofluidic devices. Both nanobubbles and nanodrops are typically nucleated by exchanging fluids over a suitable substrate. However, the nucleation experiments present many challenges, such as reproducibility and the possibility of contamination. The use of one-use plastic syringes and needle cannulas in nucleation experiments can introduce polymeric contamination. A contaminated experiment may nucleate bubbles, drops or both. Moreover, it is surprisingly difficult to distinguish between bubbles and drops under the usual atomic force microscopy or optical techniques. Here we present an experimental study comparing bubbles and oil (PDMS) drops on an atomically smooth surface (HOPG). Instead of nucleating the objects via solvent exchange, we directly introduced bubbles via electrolysis, and oil drops by injecting a dilute solution. Contrary to previous reports, we find that under careful AFM characterisation, liquid drops and gaseous bubbles respond differently to a change in imaging force, and moreover present different characteristic force curves.

  11. Filter aids influence on pressure drop across a filtration system

    Science.gov (United States)

    Hajar, S.; Rashid, M.; Nurnadia, A.; Ammar, M. R.; Hasfalina, C. M.

    2017-06-01

    Filter aids is commonly used to reduce pressure drop across air filtration system as it helps to increase the efficiency of filtration of accumulated filter cake. Filtration velocity is one of the main parameters that affect the performance of filter aids material. In this study, a formulated filter aids consisting of PreKot™ and activated carbon mixture (designated as PrekotAC) was tested on PTFE filter media under various filtration velocities of 5, 6, and 8 m/min at a constant material loading of 0.2 mg/mm2. Results showed that pressure drop is highly influenced by filtration velocity where higher filtration velocity leads to a higher pressure drop across the filter cake. It was found that PrekotAC performed better in terms of reducing the pressure drop across the filter cake even at the highest filtration velocity. The diversity in different particle size distribution of non-uniform particle size in the formulated PrekotAC mixture presents a higher permeability causes a lower pressure drop across the accumulated filter cake. The finding suggests that PrekotAC is a promising filter aids material that helps reducing the pressure drop across fabric filtration system.

  12. Afterlife of a Drop Impacting a Liquid Pool

    Science.gov (United States)

    Saha, Abhishek; Wei, Yanju; Tang, Xiaoyu; Law, Chung K.

    2017-11-01

    Drop impact on liquid pool is ubiquitous in industrial processes, such as inkjet printing and spray coating. While merging of drop with the impacted liquid surface is essential to facilitate the printing and coating processes, it is the afterlife of this merged drop and associated mixing which control the quality of the printed or coated surface. In this talk we will report an experimental study on the structural evolution of the merged droplet inside the liquid pool. First, we will analyze the depth of the crater created on the pool surface by the impacted drop for a range of impact inertia, and we will derive a scaling relation and the associated characteristic time-scale. Next, we will focus on the toroidal vortex formed by the moving drop inside the liquid pool and assess the characteristic time and length scales of the penetration process. The geometry of the vortex structure which qualitatively indicates the degree of mixedness will also be discussed. Finally, we will present the results from experiments with various viscosities to demonstrate the role of viscous dissipation on the geometry and structure formed by the drop. This work is supported by the Army Research Office and the Xerox Corporation.

  13. Drop formation of black liquor spraying; Mustalipeaen pisaroituminen

    Energy Technology Data Exchange (ETDEWEB)

    Fogelholm, C.J.; Kankkunen, A.; Nieminen, K.; Laine, J.; Miikkulainen, P. [Helsinki Univ. of Technology, Otaniemi (Finland): Lab. of Energy Technology and Environmental Protection

    1997-10-01

    Black liquor is a spent liquor of the pulp and paper industry. It is burned in kraft recovery boilers for chemical and energy recovery. The high dry solids content and viscosity of black liquor require a high spraying temperature. This affects the performance of the boiler. Kraft recovery boiler deposit formation, emissions and chemical recovery are strongly affected by the drop size and the velocity of the black liquor spray formed by a splashplate nozzle. The sheet breakup mechanism is studied with a system based on a video and image-analysis. The drop size of mill-scale nozzles was measured also with an image-analysis-system. Measurements were carried out in a spray test chamber. The sheet breakup mechanism and drop size tests were carried out both below and over the boiling point of black liquor. Special attention was paid to the effect of flashing on drop formation. Temperature increase normally decreases drop size. In the temperature where the wavy-sheet disintegration changes to perforated-sheet disintegration the drop size increases. Spray velocity rises when the temperature is increased above the boiling point. (orig.)

  14. The Relationship between Negative Stem and Taxonomy of Multiple-Choice Questions in Residency Pre-Board and Board Exams

    Directory of Open Access Journals (Sweden)

    Mohammad Hasan Karegar Maher

    2016-06-01

    Full Text Available Introduction: Multiple-choice question tests are considered as one of the most common assessment methods, frequently used in university tests. This study examined the relationship between question taxonomy and negative stem questions in university pre-board tests in Tabriz University of Medical Sciences and national boards tests in internal medicine, general surgery, pediatrics and obstetrics and gynecology residency examination from 2010-2011. Methods: In this cross-sectional study, 2400 written multiple-choice questions related to the mentioned fields were studied in terms of the relationship between taxonomy levels of the questions and their stems. If there were a negative word or negative concept in the question body, it was considered a negative stem. Taxonomy was graded: taxonomy I, ability to remember facts, Taxonomy II, ability to interpret data and taxonomy III ability to solve a new problem. The data collected were analyzed by SPSS18. P-value<0.05 was considered significant. Results: A total of 2400 questions from 8 tests (board, pre-board in 4 fields were studied. In total, 23.1% of pre-board tests and 16.6% of national board tests had negative stems and the difference was statistically significant (P=0.0001. In this study 31.1% of questions were designed with positive stems and 63.9% with negative stems in taxonomy level I(P=0.0001. There is a correlation between negative stem questions and their taxonomy. This means that 63.9% of negative stem and 31.1% of positive stem questions have been designed in taxonomy level I(P=0.0001. Conclusion: The use of negative stem questions considerably resulted in the design of low-level cognitive questions.

  15. Calculation of pressure drop and flow redistribution in the LMFBR core

    International Nuclear Information System (INIS)

    Morgado, O.J.

    1984-01-01

    The flow redistribution through fuel assemblies of LMFBRs: for the correct calculation of mass flow rates and pressure drop, are studied. Using a quasi-static formulation of conservation equations of mass and energy, a computer program was developed to simulate any arbitrary number of flow channels, operating at different linear power levels. Therefore f flow channels, operating at different linear power levels. Therefore, it was possible to perform thermal transient calculations for the Clinch River reactor core. The results of the calculations agree with the data found in the literature and supply accurate information about flow redistribution, average temperature, and pressure drop in the core, when the reactor is operated at conditions from the designed flow conditions, as is always the case in a load changing operation, or during transients. (Autor) [pt

  16. Microscopic description of a drop on a solid surface.

    Science.gov (United States)

    Ruckenstein, Eli; Berim, Gersh O

    2010-06-14

    Two approaches recently suggested for the treatment of macro- or nanodrops on smooth or rough, planar or curved, solid surfaces, based on fluid-fluid and fluid-solid interaction potentials are reviewed. The first one employs the minimization of the total potential energy of a drop by assuming that the drop has a well defined profile and a constant liquid density in its entire volume with the exception of the monolayer nearest to the surface where the density has a different value. As a result, a differential equation for the drop profile as well as the necessary boundary conditions are derived which involve the parameters of the interaction potentials and do not contain such macroscopic characteristics as the surface tensions. As a consequence, the macroscopic and microscopic contact angles which the drop profile makes with the surface can be calculated. The macroscopic angle is obtained via the extrapolation of the circular part of the drop profile valid at some distance from the surface up to the solid surface. The microscopic angle is formed at the intersection of the real profile (which is not circular near the surface) with the surface. The theory provides a relation between these two angles. The ranges of the microscopic parameters of the interaction potentials for which (i) the drop can have any height (volume), (ii) the drop can have a restricted height but unrestricted volume, and (iii) a drop cannot be formed on the surface were identified. The theory was also extended to the description of a drop on a rough surface. The second approach is based on a nonlocal density functional theory (DFT), which accounts for the inhomogeneity of the liquid density and temperature effects, features which are missing in the first approach. Although the computational difficulties restrict its application to drops of only several nanometers, the theory can be applied indirectly to macrodrops by calculating the surface tensions and using the Young equation to determine the

  17. An experimental study on two-phase pressure drop in small diameter horizontal, downward inclined and vertical tubes

    Directory of Open Access Journals (Sweden)

    Autee Arun

    2015-01-01

    Full Text Available An experimental study of two-phase pressure drop in small diameter tubes orientated horizontally, vertically and at two other downward inclinations of θ= 300 and θ = 600 is described in this paper. Acrylic transparent tubes of internal diameters 4.0, 6.0, and 8.0 mm with lengths of 400 mm were used as the test section. Air-water mixture was used as the working fluid. Two-phase pressure drop was measured and compared with the existing correlations. These correlations are commonly used for calculation of pressure drop in macro and mini-microchannels. It is observed that the existing correlations are inadequate in predicting the two-phase pressure drop in small diameter tubes. Based on the experimental data, a new correlation has been proposed for predicting the two-phase pressure drop. This correlation is developed by modification of Chisholm parameter C by incorporating different parameters. It was found that the proposed correlation predicted two-phase pressure drop at satisfactory level.

  18. 42 CFR 405.1840 - Board jurisdiction.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false Board jurisdiction. 405.1840 Section 405.1840... Appeals § 405.1840 Board jurisdiction. (a) General rules. (1) After a request for a Board hearing is filed...) of this section, whether or not it has jurisdiction to grant a hearing on each of the specific...

  19. 75 FR 8699 - Good Neighbor Environmental Board

    Science.gov (United States)

    2010-02-25

    ... ENVIRONMENTAL PROTECTION AGENCY [FRL-9117-9] Good Neighbor Environmental Board AGENCY: Environmental Protection Agency (EPA). ACTION: Notice of meeting. SUMMARY: Under the Federal Advisory Committee Act, Public Law 92-463, EPA gives notice of a meeting of the Good Neighbor Environmental Board (Board...

  20. 7 CFR 1205.308 - Cotton Board.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false Cotton Board. 1205.308 Section 1205.308 Agriculture... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE COTTON RESEARCH AND PROMOTION Cotton Research and Promotion Order Definitions § 1205.308 Cotton Board. Cotton Board means the administrative...

  1. 7 CFR 1216.4 - Board.

    Science.gov (United States)

    2010-01-01

    ... ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE PEANUT PROMOTION, RESEARCH, AND INFORMATION ORDER Peanut Promotion, Research, and Information Order Definitions § 1216.4 Board. Board means the administrative body referred to as the National Peanut Board established pursuant to § 1216.40. ...

  2. 7 CFR 1206.2 - Board.

    Science.gov (United States)

    2010-01-01

    ... ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE MANGO PROMOTION, RESEARCH, AND INFORMATION Mango Promotion, Research, and Information Order Definitions § 1206.2 Board. Board or National Mango Promotion Board means the administrative body established pursuant to § 1206.30, or such other name as...

  3. 49 CFR 1151.4 - Board determination.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 8 2010-10-01 2010-10-01 false Board determination. 1151.4 Section 1151.4 Transportation Other Regulations Relating to Transportation (Continued) SURFACE TRANSPORTATION BOARD, DEPARTMENT OF TRANSPORTATION RULES OF PRACTICE FEEDER RAILROAD DEVELOPMENT PROGRAM § 1151.4 Board determination...

  4. 77 FR 15091 - Environmental Management Advisory Board

    Science.gov (United States)

    2012-03-14

    ... Environmental Management Advisory Board AGENCY: Department of Energy. ACTION: Notice of Solicitation of Nominations for Appointment as a member of the Environmental Management Advisory Board. SUMMARY: In accordance... soliciting nominations for candidates to fill vacancies on the Environmental Management Advisory Board (EMAB...

  5. 76 FR 21877 - Environmental Management Advisory Board

    Science.gov (United States)

    2011-04-19

    ... Environmental Management Advisory Board AGENCY: Department of Energy. ACTION: Notice of call for nominations for appointment to the Environmental Management Advisory Board. SUMMARY: This notice constitutes an open call to the public to submit nominations for membership on the Environmental Management Advisory Board. DATES...

  6. 76 FR 8848 - Disciplinary Appeals Board Panel

    Science.gov (United States)

    2011-02-15

    ... AFFAIRS Disciplinary Appeals Board Panel AGENCY: Department of Veterans Affairs. ACTION: Notice with... constitute the Disciplinary Appeals Board Panel from which Board members in a case are appointed. This notice announces that the roster of employees on the Panel is available for review and comment. Employees, employee...

  7. 77 FR 71873 - Disciplinary Appeals Board Panel

    Science.gov (United States)

    2012-12-04

    ... AFFAIRS Disciplinary Appeals Board Panel AGENCY: Department of Veterans Affairs. ACTION: Notice with... constitute the Disciplinary Appeals Board Panel from which Board members in a case are appointed. This notice announces that the roster of employees on the Panel is available for review and comment. Employees, employee...

  8. 76 FR 77327 - Disciplinary Appeals Board Panel

    Science.gov (United States)

    2011-12-12

    ... AFFAIRS Disciplinary Appeals Board Panel AGENCY: Department of Veterans Affairs. ACTION: Notice with... constitute the Disciplinary Appeals Board Panel from which Board members in a case are appointed. This notice announces that the roster of employees on the Panel is available for review and comment. Employees, employee...

  9. Boys' boarding school management: understanding the choice ...

    African Journals Online (AJOL)

    marketing principles to compete effectively with boarding schools throughout the country and beyond. Customers .... the school, such as food in the boarding establishment) and the process of delivering the service (Palmer .... factors other than the academic performance of the school alone may play a role, as the boarding ...

  10. The diet board: welfare impacts of a novel method of dietary restriction in laboratory rats

    DEFF Research Database (Denmark)

    Kasanen, I H E; Inhilä, K J; Vainio, O M

    2009-01-01

    Laboratory rats are commonly fed ad libitum (AL). Moderate dietary restriction (DR) decreases mortality and morbidity when compared with AL feeding, but there are several obstacles to the implementation of DR. Traditional methods of restricted feeding disrupt normal diurnal eating rhythms...... and are not compatible with group housing. We have designed a novel method, the diet board, to restrict the feeding of group-housed rats. Animals fed from the diet board had 15% lower body weight than the AL-fed animals at the age of 17 weeks. The welfare effects of diet board feeding were assessed by comparing...... the stress physiology of diet board fed animals with that of AL-fed animals. Diet board feeding was associated with higher serum corticosterone levels and lower faecal secretion of IgA, suggesting the diet board causes a stress reaction. However, the AL-fed group had larger adrenal glands with higher...

  11. Many Drops Interactions I: Simulation of Coalescence, Flocculation and Fragmentation of Multiple Colliding Drops with Smoothed Particle Hydrodynamics

    Directory of Open Access Journals (Sweden)

    Alejandro Acevedo-Malavé

    2012-06-01

    Full Text Available Smoothed Particle Hydrodynamics (SPH is a Lagrangian mesh-free formalism and has been useful to model continuous fluid. This formalism is employed to solve the Navier-Stokes equations by replacing the fluid with a set of particles. These particles are interpolation points from which properties of the fluid can be determined. In this study, the SPH method is applied to simulate the hydrodynamics interaction of many drops, showing some settings for the coalescence, fragmentation and flocculation problem of equally sized liquid drops in three-dimensional spaces. For small velocities the drops interact only through their deformed surfaces and the flocculation of the droplets arises. This result is very different if the collision velocity is large enough for the fragmentation of droplets takes place. We observe that for velocities around 15 mm/ms the coalescence of droplets occurs. The velocity vector fields formed inside the drops during the collision process are shown.

  12. 14 CFR 250.9 - Written explanation of denied boarding compensation and boarding priorities.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Written explanation of denied boarding compensation and boarding priorities. 250.9 Section 250.9 Aeronautics and Space OFFICE OF THE SECRETARY... explanation of denied boarding compensation and boarding priorities. (a) Every carrier shall furnish...

  13. 14 CFR 250.5 - Amount of denied boarding compensation for passengers denied boarding involuntarily.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Amount of denied boarding compensation for passengers denied boarding involuntarily. 250.5 Section 250.5 Aeronautics and Space OFFICE OF THE SECRETARY... boarding compensation for passengers denied boarding involuntarily. (a) Subject to the exceptions provided...

  14. The Perceptions of Georgia School Board Members' Need for Training on School Board Governance

    Science.gov (United States)

    Nutt, Pamela Studdard

    2010-01-01

    This study explored the perceptions of training needs of school board members in Georgia. The study examined perceptions of school board chairs, board members with 1 to 5 years experience, members with 6 to 10 years experience, members with 11 to 15 years experience and board members with 16 plus years experience in the areas of school board…

  15. 77 FR 5020 - Civilian Board of Contract Appeals; Information Collection; Civilian Board of Contract Appeals...

    Science.gov (United States)

    2012-02-01

    ...] Civilian Board of Contract Appeals; Information Collection; Civilian Board of Contract Appeals Rules of... regarding the Civilian Board of Contract Appeals (CBCA) Rules of Procedure. Public comments are particularly... Information Collection IC 3090-0221, Civilian Board of Contract Appeals Rules of Procedure, by any of the...

  16. The Atomic Energy Control Board

    International Nuclear Information System (INIS)

    Doern, G.B.

    1976-01-01

    This study describes and assesses the regulatory and administrative processes and procedures of the Atomic Energy Control Board, the AECB. The Atomic Energy Control Act authorized the AECB to control atomic energy materials and equipment in the national interest and to participate in measures for the international control of atomic energy. The AECB is authorized to make regulations to control atomic energy materials and equipment and to make grants in support of atomic energy research. (author)

  17. Los Angeles School Board Race Shatters Spending Records

    Science.gov (United States)

    Maxwell, Lesli A.

    2013-01-01

    The price tag to win a seat in this week's primary election for the Los Angeles school board climbed to unprecedented levels, as a massive influx of outside cash has turned a local campaign into a national showdown pitting the long-standing influence of teachers' unions against the expanding imprint of deep-pocketed education activists. The high…

  18. Using Digital Board Games for Genuine Communication in EFL Classrooms

    Science.gov (United States)

    Wu, Chia-Jung; Chen, Gwo-Dong; Huang, Chi-Wen

    2014-01-01

    EFL learners in Taiwan have a low-level communication ability because many learners are still not provided opportunities to use language for genuine communication in classrooms and receive insufficient language input due to the environment. This study examines the use of digital board game language learning set in a task-collaborative platform,…

  19. 75 FR 67709 - National Assessment Governing Board; Meeting

    Science.gov (United States)

    2010-11-03

    ..., developing appropriate student achievement levels for each grade and subject tested, developing standards and... implications for the NAEP assessment schedule and for international linking studies. The discussion of contract...:15 p.m., Board members will receive their annual ethics briefing from the Office of General Counsel...

  20. The Opportunities of Scarcity: State Coordinating and Governing Boards.

    Science.gov (United States)

    Smith, Van P.

    1983-01-01

    The dangers to higher education also represent important opportunities for growth and creativity. State level coordinating and governing boards need to examine their leadership responsibilities, the role of new technologies in higher education, and the appropriate response to faculty retirement patterns in the near future. (MSE)

  1. Caffeine eye drops protect against UV-B cataract.

    Science.gov (United States)

    Kronschläger, Martin; Löfgren, Stefan; Yu, Zhaohua; Talebizadeh, Nooshin; Varma, Shambhu D; Söderberg, Per

    2013-08-01

    The purpose of this study was to investigate if topically applied caffeine protects against in vivo ultraviolet radiation cataract and if so, to estimate the protection factor. Three experiments were carried out. First, two groups of Sprague-Dawley rats were pre-treated with a single application of either placebo or caffeine eye drops in both eyes. All animals were then unilaterally exposed in vivo to 8 kJ/m(2) UV-B radiation for 15 min. One week later, the lens GSH levels were measured and the degree of cataract was quantified by measurement of in vitro lens light scattering. In the second experiment, placebo and caffeine pre-treated rats were divided in five UV-B radiation dose groups, receiving 0.0, 2.6, 3.7, 4.5 or 5.2 kJ/m(2) UV-B radiation in one eye. Lens light scattering was determined after one week. In the third experiment, placebo and caffeine pre-treated rats were UV-B-exposed and the presence of activated caspase-3 was visualized by immunohistochemistry. There was significantly less UV-B radiation cataract in the caffeine group than in the placebo group (95% confidence interval for mean difference in lens light scattering between the groups = 0.10 ± 0.05 tEDC), and the protection factor for caffeine was 1.23. There was no difference in GSH levels between the placebo- and the caffeine group. There was more caspase-3 staining in UV-B-exposed lenses from the placebo group than in UV-B-exposed lenses from the caffeine group. Topically applied caffeine protects against ultraviolet radiation cataract, reducing lens sensitivity 1.23 times. Copyright © 2013 Elsevier Ltd. All rights reserved.

  2. Transport and Storage Cask Safety Assessment - Drop Tests and Numerical Calculations -

    International Nuclear Information System (INIS)

    Voelzke, H.; Wille, F.; Wieser, G.; Quercetti, Th.

    2006-01-01

    BAM (the German Federal Institute for Materials Research and Testing) has been performing cask design testing for more than 30 years with a large number of prototype casks of original dimensions and of 1:2 or 1:3 scales. In 2004 a brand new drop test facility was built at the new BAM test facility at Horstwalde about 80 km to the south of Berlin. In September 2004 first demonstration tests with 2 different cask designs were performed in connection with the PATRAM 2004 conference held in Berlin. The dropped prototype casks had gross masses of 141 and 181 metric tons. Since that time BAM has been performing a lot of more drop tests with new cask designs developed by different international cask manufacturers for getting German Type B(U) transport licenses. Current safety assessments especially for mechanical accident scenarios require a combination of experimental and analytical/numerical proofs commonly, because both methods offer specific options and advantages with respect to more and more detailed structural analyses. That again is a consequence of the permanent cask design optimisation for commercial reasons leading to higher stress levels in general. For that reason BAM also improves its numerical analyses capacities including the operation of different software codes. A general BAM guideline describing basic requirements for numerical safety assessment reports gives a good orientation for both applicants and inspectors. But different details of any cask design and safety assessment have to be taken into account and lead to specific questions, investigations and experiences. This paper gives an overview about the new BAM drop test facility and the ongoing drop testing there and it presents current experiences and results of numerical cask analyses and the specific methods developed and used by BAM. In this context special attention is turned to the correlation between experimental and numerical results and an outlook to future developments is given. (authors)

  3. Drop Calculations of HLW Canister and Pu Can-in-Canister

    Energy Technology Data Exchange (ETDEWEB)

    Sreten Mastilovic

    2001-07-31

    The objective of this calculation is to determine the structural response of the standard high-level waste (HLW) canister and the canister containing the cans of immobilized plutonium (Pu) (''can-in-canister'' [CIC] throughout this document) subjected to drop DBEs (design basis events) during the handling operation. The evaluated DBE in the former case is 7-m (23-ft) vertical (flat-bottom) drop. In the latter case, two 2-ft (0.61-m) corner (oblique) drops are evaluated in addition to the 7-m vertical drop. These Pu CIC calculations are performed at three different temperatures: room temperature (RT) (20 C ), T = 200 F = 93.3 C , and T = 400 F = 204 C ; in addition to these the calculation characterized by the highest maximum stress intensity is performed at T = 750 F = 399 C as well. The scope of the HLW canister calculation is limited to reporting the calculation results in terms of: stress intensity and effective plastic strain in the canister, directional residual strains at the canister outer surface, and change of canister dimensions. The scope of Pu CIC calculation is limited to reporting the calculation results in terms of stress intensity, and effective plastic strain in the canister. The information provided by the sketches from Reference 26 (Attachments 5.3,5.5,5.8, and 5.9) is that of the potential CIC design considered in this calculation, and all obtained results are valid for this design only. This calculation is associated with the Plutonium Immobilization Project and is performed by the Waste Package Design Section in accordance with Reference 24. It should be noted that the 9-m vertical drop DBE, included in Reference 24, is not included in the objective of this calculation since it did not become a waste acceptance requirement. AP-3.124, ''Calculations'', is used to perform the calculation and develop the document.

  4. Drop Calculations of HLW Canister and Pu Can-in-Canister

    International Nuclear Information System (INIS)

    Sreten Mastilovic

    2001-01-01

    The objective of this calculation is to determine the structural response of the standard high-level waste (HLW) canister and the canister containing the cans of immobilized plutonium (Pu) (''can-in-canister'' [CIC] throughout this document) subjected to drop DBEs (design basis events) during the handling operation. The evaluated DBE in the former case is 7-m (23-ft) vertical (flat-bottom) drop. In the latter case, two 2-ft (0.61-m) corner (oblique) drops are evaluated in addition to the 7-m vertical drop. These Pu CIC calculations are performed at three different temperatures: room temperature (RT) (20 C), T = 200 F = 93.3 C , and T = 400 F = 204 C ; in addition to these the calculation characterized by the highest maximum stress intensity is performed at T = 750 F = 399 C as well. The scope of the HLW canister calculation is limited to reporting the calculation results in terms of: stress intensity and effective plastic strain in the canister, directional residual strains at the canister outer surface, and change of canister dimensions. The scope of Pu CIC calculation is limited to reporting the calculation results in terms of stress intensity, and effective plastic strain in the canister. The information provided by the sketches from Reference 26 (Attachments 5.3,5.5,5.8, and 5.9) is that of the potential CIC design considered in this calculation, and all obtained results are valid for this design only. This calculation is associated with the Plutonium Immobilization Project and is performed by the Waste Package Design Section in accordance with Reference 24. It should be noted that the 9-m vertical drop DBE, included in Reference 24, is not included in the objective of this calculation since it did not become a waste acceptance requirement. AP-3.124, ''Calculations'', is used to perform the calculation and develop the document

  5. Graedel named to AIP Board

    Science.gov (United States)

    Maggs, William Ward

    Thomas E. Graedel, an atmospheric scientist at AT&T Bell Laboratories (Murray Hill, N.J.), has been made an AGU representative to the Governing Board of the American Institute of Physics (AIP). The board oversees the operations of AIP, a nonprofit umbrella organization for 10 member societies, including AGU. Other AGU members currently on the governing board include Orson Anderson, a geophysicist at the University of California, Los Angeles; AGU General Secretary Peter M. Bell of the Norton Company, Worcester, Mass.; AGU Executive Director A. F. Spilhaus, Jr.; and Martin Walt, a geophysicist with the Lockheed Corporation in Palo Alto, Calif.All AGU members receive the benefits of membership in AIP, including the monthly magazine Physics Today. Other AIP services available to AGU members include access to an employment service, AIP's electronic network Pi-NET, and an insurance program. AGU members can also subscribe to journals published by the American Physical Society, another AIP member society, at discounted rates.—WWM

  6. Integrated reporting and board features

    Directory of Open Access Journals (Sweden)

    Rares HURGHIS

    2017-02-01

    Full Text Available In the last two decades the concept of sustainability reporting gained more importance in the companies’ annual reports, a trend which is embedded also in integrated reporting. Issuing an integrated report became a necessity, because the report explains to the investors how the organization creates value over time. The governance structure, more exactly the board of directors, decides whether or not the company will issue an integrated report. Thus, are there certain features of the board that might influence the issue of an integrated report? Do the companies which issue an integrated report have certain features of the governance structure? Looking for an answer to these questions, we seek for any possible correlations between a disclosure index and the corporate governance structure characteristics, on a sample from the companies participating at the International Integrated Reporting Council Examples Database. The results highlight that only the size of the board influences the extent to which the issued integrated report is in accordance with the International Framework.

  7. Turning Schools Around: The National Board Certification Process as a School Improvement Strategy. Research Brief

    Science.gov (United States)

    Jaquith, Ann; Snyder, Jon

    2016-01-01

    Can the National Board certification process support school improvement where large proportions of students score below grade level on standardized tests? This SCOPE study examines a project that sought to seize and capitalize upon the learning opportunities embedded in the National Board certification process, particularly opportunities to learn…

  8. Turning Schools Around: The National Board Certification Process as a School Improvement Strategy

    Science.gov (United States)

    Jaquith, Ann; Snyder, Jon

    2016-01-01

    Can the National Board certification process support school improvement where large proportions of students score below grade level on standardized tests? This SCOPE study examines a project that sought to seize and capitalize upon the learning opportunities embedded in the National Board certification process, particularly opportunities to learn…

  9. The Effects of School Board Consolidation and Financing on Student Performance

    Science.gov (United States)

    Leach, John; Payne, A. Abigail; Chan, Steve

    2010-01-01

    Over the last 20 years, states and provinces have become increasingly involved in the financing and administration of elementary and secondary education. Local school boards, however, still retain control over key aspects of the provision of education. Historically, these boards were organized at the community level so as to meet the wants of the…

  10. FASTBUS Standard Routines implementation for Fermilab embedded processor boards

    International Nuclear Information System (INIS)

    Pangburn, J.; Patrick, J.; Kent, S.; Oleynik, G.; Pordes, R.; Votava, M.; Heyes, G.; Watson, W.A. III

    1992-10-01

    In collaboration with CEBAF, Fermilab's Online Support Department and the CDF experiment have produced a new implementation of the IEEE FASTBUS Standard Routines for two embedded processor FASTBUS boards: the Fermilab Smart Crate Controller (FSCC) and the FASTBUS Readout Controller (FRC). Features of this implementation include: portability (to other embedded processor boards), remote source-level debugging, high speed, optional generation of very high-speed code for readout applications, and built-in Sun RPC support for execution of FASTBUS transactions and lists over the network

  11. Board Saver for Use with Developmental FPGAs

    Science.gov (United States)

    Berkun, Andrew

    2009-01-01

    A device denoted a board saver has been developed as a means of reducing wear and tear of a printed-circuit board onto which an antifuse field programmable gate array (FPGA) is to be eventually soldered permanently after a number of design iterations. The need for the board saver or a similar device arises because (1) antifuse-FPGA design iterations are common and (2) repeated soldering and unsoldering of FPGAs on the printed-circuit board to accommodate design iterations can wear out the printed-circuit board. The board saver is basically a solderable/unsolderable FPGA receptacle that is installed temporarily on the printed-circuit board. The board saver is, more specifically, a smaller, square-ring-shaped, printed-circuit board (see figure) that contains half via holes one for each contact pad along its periphery. As initially fabricated, the board saver is a wider ring containing full via holes, but then it is milled along its outer edges, cutting the via holes in half and laterally exposing their interiors. The board saver is positioned in registration with the designated FPGA footprint and each via hole is soldered to the outer portion of the corresponding FPGA contact pad on the first-mentioned printed-circuit board. The via-hole/contact joints can be inspected visually and can be easily unsoldered later. The square hole in the middle of the board saver is sized to accommodate the FPGA, and the thickness of the board saver is the same as that of the FPGA. Hence, when a non-final FPGA is placed in the square hole, the combination of the non-final FPGA and the board saver occupy no more area and thickness than would a final FPGA soldered directly into its designated position on the first-mentioned circuit board. The contact leads of a non-final FPGA are not bent and are soldered, at the top of the board saver, to the corresponding via holes. A non-final FPGA can readily be unsoldered from the board saver and replaced by another one. Once the final FPGA design

  12. X-38 Drop Model: Landing Sequence Collage from Cessna Drop Test

    Science.gov (United States)

    1995-01-01

    This sequence of photographs shows a 4-foot-long model of NASA's X-38 gliding to earth after being dropped from a Cessna aircraft in late 1995. The model was used to test the ram-air parafoil landing system, which could allow for accurate and controlled landings of an emergency Crew Return Vehicle spacecraft returning to earth. The X-38 Crew Return Vehicle (CRV) research project is designed to develop the technology for a prototype emergency crew return vehicle, or lifeboat, for the International Space Station. The project is also intended to develop a crew return vehicle design that could be modified for other uses, such as a joint U.S. and international human spacecraft that could be launched on the French Ariane-5 Booster. The X-38 project is using available technology and off-the-shelf equipment to significantly decrease development costs. Original estimates to develop a capsule-type crew return vehicle were estimated at more than $2 billion. X-38 project officials have estimated that development costs for the X-38 concept will be approximately one quarter of the original estimate. Off-the-shelf technology is not necessarily 'old' technology. Many of the technologies being used in the X-38 project have never before been applied to a human-flight spacecraft. For example, the X-38 flight computer is commercial equipment currently used in aircraft and the flight software operating system is a commercial system already in use in many aerospace applications. The video equipment for the X-38 is existing equipment, some of which has already flown on the space shuttle for previous NASA experiments. The X-38's primary navigational equipment, the Inertial Navigation System/Global Positioning System, is a unit already in use on Navy fighters. The X-38 electromechanical actuators come from previous joint NASA, U.S. Air Force, and U.S. Navy research and development projects. Finally, an existing special coating developed by NASA will be used on the X-38 thermal tiles to

  13. Project Fog Drops. Part 2: Laboratory investigations

    Science.gov (United States)

    Kocmond, W. C.; Mack, E. J.; Katz, U.; Pilie, R. J.

    1972-01-01

    Measurements of the total nucleus concentration and cloud condensation nuclei (CCN) were acquired for several conditions representing both high normal and severe pollution levels for the Los Angeles Basin as well as clean filtered air. The data show that in filtered air there is a large photochemically induced increase in the total particle content within a few minutes after starting the lamp. The concentration of CCN remains near zero, until sufficient coagulation and condensation occurs on the smaller Aitken particles. The addition of gaseous pollutants to filtered air results in large increases in the photochemical production of both the cloud and Aitken nucleus concentration. Fogs were also generated under controlled, reproducible conditions in the cloud chamber and seeded with aerosols of various compounds which form monomolecular surface films at air-water interfaces. Visibility characteristics and droplet data were obtained. The data suggest that droplet growth on treated nuclei can be retarded but fog formation was not significantly altered by the chemical seeding.

  14. BoardScope: a debug tool for reconfigurable systems

    Science.gov (United States)

    Levi, Delon; Guccione, Steven A.

    1998-10-01

    BoardScope is a portable, interactive debug tool for Xilinx FPGA-based hardware. BoardScope features simple but powerful graphical interfaces for viewing FPGA circuits in their operational state. The main display graphically shows the Configurable Logic Block (CLB) flip-flop states of all FPGA devices in the system. This display indicates overall dataflow and is used to find design errors, such as clocking problems or incorrect initialization or reset. The CLB display shows the complete state, including LUT values and flip-flop configuration, of any CLB. Finally, a symbol file may be used to drive a waveform display. The waveform display permits both bit-level signals and multibit busses to be viewed in a fashion similar to that used by circuit simulators. BoardScope is implemented completely in JavaTM, using the Abstract Window Toolkit version 1.1. The interface to the hardware is provided by XHWIF, the Xilinx standard HardWare InterFace for FPGA based hardware. This simplifies porting, and provides remote access capabilities. Remote access allows multiple users to communicate with the hardware across a network. BoardScope currently runs on the WildForceTM and WildOneTM boards from Annapolis Microsystems, and the PCI Pamette from Digital Equipment Corporation. Ports to other systems are currently under way.

  15. Board competency explanations for differentiation in a harmonisation environment

    DEFF Research Database (Denmark)

    Holm, Claus; Schøler, Finn

    Some company leaders decide that their companies should differentiate themselves from others even though the regulatory establishments such as the European Union and IASB are making elaborate efforts to emphasise comparability and the need for harmonisation of reporting behaviour and governance...... implementation and high level of CG disclosure and two instances involving choice of governance structure: the abandonment of joint audit (change from two to one auditor) and the choice to use audit committee as part of the company governance structure. Our study is based on collected financial and corporate...... governance data for 100 listed Danish companies for 2004-2005. Across these four differentiation decisions we find varying support for the three recommended types of competencies of board members. We find that IFRS implementation is related to board competency indicated by having foreigner board members...

  16. The Effect of Board Size and Board Composition on Firms Corporate Environmental Disclosure: A Study of Selected Firms in Nigeria

    Directory of Open Access Journals (Sweden)

    Uwalomwa Nil Uwuigbe

    2011-10-01

    Full Text Available Environmental problems have become major headlines due to the negative effects they bring to the stability of the ecosystem. Thus, the increased awareness of social responsibility or, specifically, environmental concern is now a challenge facing the corporate world. Hence this study tests whether board size and board composition have any association with the level of firms’ corporate environmental disclosure in annual reports. To achieve the objective of this study, a total of 40 listed firms on the floor of the Nigerian stock exchange market were used. Also, the study critically developed and utilized the Kinder Lydenberg Domini (KLD rating scheme to analyze the level of corporate environmental disclosure made by firms in their annual reports for the period 2006-2010. In addition, the simple regression analysis was used to test the research propositions as stated in the study. However, empirical findings from the study reveal that while board size has a significant negative relationship with the level of corporate environmental disclosure; board composition on the other hand has a significant positive relationship with the level of firms’ corporate environmental disclosure in the annual report.

  17. From Global Firms to Global Boards?

    DEFF Research Database (Denmark)

    Thomsen, Steen; Gregoric, Aleksandra; Randøy, Trond

    2011-01-01

    This paper examines the internationalization of Nordic company boards during 2001-2008. Using Poisson pooled and panel estimators we find that financial rather than commercial internationalization drives the recruitment of international board members. Foreign listing and foreign ownership...... are significant whereas international sales and operations are not. When we extend “board internationalization” to encompass national directors with international experience we find that shareholders may opt for domestic board members with that experience to match the firm’s commercial internationalization....... This indicates some support for the view that different kinds of firm internationalization – commercial versus financial - might lead to different types of board internationalization. We find no evidence that the internationalization of boards is limited by the conservatism of existing national board members...

  18. A PIV Study of Drop-interface Coalescence with Surfactants

    Science.gov (United States)

    Weheliye, Weheliye Hashi; Dong, Teng; Angeli, Panagiota

    2017-11-01

    In this work, the coalescence of a drop with an aqueous-organic interface was studied by Particle Image Velocimetry (PIV). The effect of surfactants on the drop surface evolution, the vorticity field and the kinetic energy distribution in the drop during coalescence were investigated. The coalescence took place in an acrylic rectangular box with 79% glycerol solution at the bottom and Exxsol D80 oil above. The glycerol solution drop was generated through a nozzle fixed at 2cm above the aqueous/oil interface and was seeded with Rhodamine particles. The whole process was captured by a high-speed camera. Different mass ratios of non-ionic surfactant Span80 to oil were studied. The increase of surfactant concentration promoted deformation of the interface before the rupture of the trapped oil film. At the early stages after film rupture, two counter-rotating vortices appeared at the bottom of the drop which then travelled to the upper part. The propagation rates, as well as the intensities of the vortices decreased at high surfactant concentrations. At early stages, the kinetic energy was mainly distributed near the bottom part of the droplet, while at later stages it was distributed near the upper part of the droplet. Programme Grant MEMPHIS, Chinese Scholarship Council (CSC).

  19. Vertical Drop Test of a YS-11 Fuselage Section

    Science.gov (United States)

    Minegishi, Masakatsu; Kumakura, Ikuo; Iwasaki, Kazuo; Shoji, Hirokazu; Yoshimoto, Norio; Terada, Hiroyuki; Sashikuma, Hirofumi; Isoe, Akira; Yamaoka, Toshihiro; Katayama, Noriaki; Hayashi, Toru; Akaso, Tetsuya

    The Structures and Materials Research Center of the National Aerospace Laboratory of Japan (NAL) and Kawasaki Heavy Industories, Ltd. (KHI) conducted a vertical drop test of a fuselage section cut from a NAMIC YS-11 transport airplane at NAL vertical drop test facility in December 2001. The main objectives of this program were to obtain background data for aircraft cabin safety by drop test of a full-scale fuselage section and to develop computational method for crash simulation. The test article including seats and anthropomorphic test dummies was dropped to a rigid impact surface at a velocity of 6.1 m/s (20 ft/s). The test condition and result were considered to be severe but potentially survivable. A finite element model of this test article was also developed using the explicit nonlinear transient-dynamic analysis code, LS-DYNA3D. An outline of analytical method and comparison of analysis result with drop test data are presented in this paper.

  20. Estimation of methacrylate monolith binding capacity from pressure drop data.

    Science.gov (United States)

    Podgornik, Aleš; Smrekar, Vida; Krajnc, Peter; Strancar, Aleš

    2013-01-11

    Convective chromatographic media comprising of membranes and monoliths represent an important group of chromatographic supports due to their flow-unaffected chromatographic properties and consequently fast separation and purification even of large biological macromolecules. Consisting of a single piece of material, common characterization procedures based on analysis of a small sample assuming to be representative for the entire batch, cannot be applied. Because of that, non-invasive characterization methods are preferred. In this work pressure drop was investigated for an estimation of dynamic binding capacity (DBC) of proteins and plasmid DNA for monoliths with different pore sizes. It was demonstrated that methacrylate monolith surface area is reciprocally proportional to pore diameter and that pressure drop on monolith is reciprocally proportional to square pore size demonstrating that methacrylate monolith microstructure is preserved by changing pore size. Based on these facts mathematical formalism has been derived predicting that DBC is in linear correlation with the square root of pressure drop. This was experimentally confirmed for ion-exchange and hydrophobic interactions for proteins and plasmid DNA. Furthermore, pressure drop was also applied for an estimation of DBC in grafted layers of different thicknesses as estimated from the pressure drop data. It was demonstrated that the capacity is proportional to the estimated grafted layer thickness. Copyright © 2012 Elsevier B.V. All rights reserved.

  1. Drop splashing: the role of surface wettability and liquid viscosity

    Science.gov (United States)

    Almohammadi, Hamed; Amirfazli, Alidad; -Team

    2017-11-01

    There are seemingly contradictory results in the literature about the role of surface wettability and drop viscosity for the splashing behavior of a drop impacting onto a surface. Motivated by such issues, we conducted a systematic experimental study where splashing behavior for a wide range of the liquid viscosity (1-100 cSt) and surface wettability (hydrophilic to hydrophobic) are examined. The experiments were performed for the liquids with both low and high surface tensions ( 20 and 72 mN/m). We found that the wettability affects the splashing threshold at high or low contact angle values. At the same drop velocity, an increase of the viscosity (up to 4 cSt) promotes the splashing; while, beyond such value, any increase in viscosity shows the opposite effect. It is also found that at a particular combination of liquid surface tension and viscosity (e.g. silicone oil, 10 cSt), an increase in the drop velocity changes the splashing to spreading. We relate such behaviors to the thickness, shape, and the velocity of the drop's lamella. Finally, to predict the splashing, we developed an empirical correlation which covers all of the previous reported data, hence clarifying the ostensible existing contradictions.

  2. Asymmetric drop coalescence launches fungal ballistospores with directionality.

    Science.gov (United States)

    Liu, Fangjie; Chavez, Roger L; Patek, S N; Pringle, Anne; Feng, James J; Chen, Chuan-Hua

    2017-07-01

    Thousands of fungal species use surface energy to power the launch of their ballistospores. The surface energy is released when a spherical Buller's drop at the spore's hilar appendix merges with a flattened drop on the adaxial side of the spore. The launching mechanism is primarily understood in terms of energetic models, and crucial features such as launching directionality are unexplained. Integrating experiments and simulations, we advance a mechanistic model based on the capillary-inertial coalescence between the Buller's drop and the adaxial drop, a pair that is asymmetric in size, shape and relative position. The asymmetric coalescence is surprisingly effective and robust, producing a launching momentum governed by the Buller's drop and a launching direction along the adaxial plane of the spore. These key functions of momentum generation and directional control are elucidated by numerical simulations, demonstrated on spore-mimicking particles, and corroborated by published ballistospore kinematics. Our work places the morphological and kinematic diversity of ballistospores into a general mechanical framework, and points to a generic catapulting mechanism of colloidal particles with implications for both biology and engineering. © 2017 The Author(s).

  3. AC Electrowetting of Polymer Aqueous Drops on Parallel Electrodes

    Science.gov (United States)

    Zhang, Lu; Chetwani, Nishant; Chang, Hsueh-Chia; Zhu, Yingxi Elaine

    2009-03-01

    We have recently observed the strong field dependence of AC-electrowetting of simple electrolyte aqueous drops on parallel gold electrodes, yet the detailed dynamic process of AC-field induced surface wetting remains unclear. In this work, we use fluorescence labeled DNA aqueous solution as a model system to directly visualize the wetting process of aqueous drops under varied AC electric fields by using combined fluorescence microscopy and contact angle goniometer. The electrowetting behavior of DNA aqueous drops is observed at AC-field frequency greater than the reciprocal of the RC time scale for electrode screening. And the onset of AC electrowetting is accompanied by the observed oscillation in drop contour shape and contact line. In addition, the ejection of nanodrops from the parent aqueous drop is observed when the threshold AC-field amplitude is exceeded. A scaling theory based on electrode interfacial screening is developed to quantify the AC-electrowetting behavior with the dependence of AC-field frequency, strength and medium conductivity.

  4. Electrohydrodynamics of drops in strong electric fields: Simulations and theory

    Science.gov (United States)

    Saintillan, David; Das, Debasish

    2016-11-01

    Weakly conducting dielectric liquid drops suspended in another dielectric liquid exhibit a wide range of dynamical behaviors when subject to an applied uniform electric field contingent on field strength and material properties. These phenomena are best described by the much celebrated Maylor-Taylor leaky dielectric model that hypothesizes charge accumulation on the drop-fluid interface and prescribes a balance between charge relaxation, the jump in Ohmic currents and charge convection by the interfacial fluid flow. Most previous numerical simulations based on this model have either neglected interfacial charge convection or restricted themselves to axisymmetric drops. In this work, we develop a three-dimensional boundary element method for the complete leaky dielectric model to systematically study the deformation and dynamics of liquid drops in electric fields. The inclusion of charge convection in our simulation permits us to investigate drops in the Quincke regime, in which experiments have demonstrated symmetry-breaking bifurcations leading to steady electrorotation. Our simulation results show excellent agreement with existing experimental data and small deformation theories. ACSPRF Grant 53240-ND9.

  5. Mapping coalescence of micron-sized drops and bubbles.

    Science.gov (United States)

    Berry, Joseph D; Dagastine, Raymond R

    2017-02-01

    Emulsion formulation, solvent extraction and multiphase microfluidics are all examples of processes that require precise control of drop or bubble collision stability. We use a previously validated numerical model to map the exact conditions under which micron-sized drops or bubbles undergo coalescence in the presence of colloidal forces and hydrodynamic effects relevant to Brownian motion and low Reynolds number flows. We demonstrate that detailed understanding of how the equilibrium surface forces vary with film thickness can be applied to make accurate predictions of the outcome of a drop or bubble collision when hydrodynamic effects are negligible. In addition, we illuminate the parameter space (i.e. interaction velocity, drop deformation, interfacial tension, etc.) at which hydrodynamic effects can stabilise collisions that are unstable at equilibrium. Further, we determine conditions for which drop or bubble collisions become unstable upon separation, caused by negative hydrodynamic pressure in the film. Lastly, we show that scaling analyses are not applicable for constant force collisions where the approach timescale is comparable to the coalescence timescale, and demonstrate that initial conditions under these circumstances cannot be ignored. Copyright © 2016 Elsevier Inc. All rights reserved.

  6. Calculation method for control rod dropping time in reactor

    International Nuclear Information System (INIS)

    Nogami, Takeki; Kato, Yoshifumi; Ishino, Jun-ichi; Doi, Isamu.

    1996-01-01

    If a control rod starts dropping, the dropping speed is rapidly increased, then settled substantially constant, rapidly decreased when it reaches a dash pot. A second detection signal generated by removing an AC component from a first detection signal is differentiated twice. The time when the maximum value among the twice differentiated values is generated is determined as a time when the control rods starts dropping. The time when minimum value among the twice differentiated values is generated is determined as a time when the control rod reaches the dash pot of the reactor. The measuring time within a range from the time when the control rod starts dropping to the time when the control rod reaches the dash pot of the reactor is determined. As a result, processing for the calculation of the dropping start time and dash pot reaching time of the control rod can be automatized. Further, it is suffice to conduct differentiation twice till the reaching time, which can facilitate the processing thereby enabling to determine a reliable time range. (N.H.)

  7. Dividing of metal and plastic components of printed circuit boards

    Directory of Open Access Journals (Sweden)

    Krenek Jiri

    2017-01-01

    Full Text Available This paper contents one possibility of PCB separation due to the temperature due to the different thermal expansion of the metal path and the plastic from which the boards are made. Using the knowledge from the literary study and the simulation environments used, we have reached the maximum analysis of the problem. The separation of metal and plastic may occur due to temperature changes if the temperature difference is sufficient. We have carried out a study of printed circuit board production so we can choose the appropriate path of separation. Furthermore, we calculated the shear stress size required to tear the conductive copper paths from the epoxy resin. The temperature field in a two-layer board was modeled in the FEMLAB and Pro/ENGINEER programming environments. From the simulated temperature field simulations, conclusions can be drawn that accurately describe the condition and characteristics of materials subjected to heat shock. They derived the resulting relationship for calculating the resulting shear stress needed to separate the conductive paths and plastic materials of the PCB. In our own experiments, we used several ways to heat PCBs. The temperature is also sufficient for the separation of tin. After using the mechanical separation of the components, they were dropped from the PCB. Mechanical separation was also used when removing conductive paths. This separation is effective, but in the newer types of PCBs, the cyclical effects of thermal shock have to be applied to the separation of copper paths. Laboratory tests have demonstrated the viability of the proposed solution. The proposed method of recycling could lead to industrial use, which requires consistent sorting of waste electrical and electronic equipment.

  8. Handling Test of Eye Drop Dispenser—Comparison of Unit-Dose Pipettes with Conventional Eye Drop Bottles

    Science.gov (United States)

    Latvala, Terho; Ropo, Auli

    2010-01-01

    Abstract Purpose The aims of this study were to investigate how elderly people handle single-use eye drop dispensers (unit-dose pipettes) and to compare the performance with conventional eye drop bottles. Methods In this open-label study, the handling of unit-dose pipettes and conventional eye drop bottles was compared in 41 elderly people who had little or no prior regular use of eye drop dispensers. The participants tested both types of dispenser once, and the following 7 variables were studied: ease/difficulty of opening the dispenser; influence of the size for handling of the dispenser; influence of the shape for handling of the dispenser; observation of the contents in the dispenser; the feeling of the dispenser in the hand; ease/difficulty of drop instillation on the eye from the dispenser; and overall performance of the eye drop dispenser. The dispensers contained isotonic saline, and a visual analog scale was used for assessment of each of the above variables. Results The mean age of the participants was 73 years. A statistically significant difference in favor of the unit-dose pipettes was found with respect to observation of the contents in the dispenser, ease of administration, and the overall performance. Women regarded the unit-dose pipettes generally better than the bottles, but such a difference was not seen in men. Conclusions The study participants managed the unit-dose pipettes at least as well as the conventional eye drop bottles. If anything, the unit-dose pipettes appeared to be easier to use. PMID:20565314

  9. Changes in Drop-Jump Landing Biomechanics During Prolonged Intermittent Exercise

    Science.gov (United States)

    Schmitz, Randy J.; Cone, John C.; Tritsch, Amanda J.; Pye, Michele L.; Montgomery, Melissa M.; Henson, Robert A.; Shultz, Sandra J.

    2014-01-01

    Background: As injury rates rise in the later stages of sporting activities, a better understanding of lower extremity biomechanics in the later phases of gamelike situations may improve training and injury prevention programs. Hypothesis: Lower extremity biomechanics of a drop-jump task (extracted from a principal components analysis) would reveal factors associated with risk of anterior cruciate ligament injury during a 90-minute individualized intermittent exercise protocol (IEP) and for 1 hour following the IEP. Study Design: Controlled laboratory study. Level of Evidence: Level 4. Methods: Fifty-nine athletes (29 women, 30 men) completed 3 sessions. The first session assessed fitness for an IEP designed to simulate the demands of a soccer match. An experimental session assessed drop-jump biomechanics, after a dynamic warm-up, every 15 minutes during the 90-minute IEP, and for 1 hour following the IEP. A control session with no exercise assessed drop-jump performance at the same intervals. Results: Two biomechanical factors early in the first half (hip flexion at initial contact and hip loading; ankle loading and knee shear force) decreased at the end of the IEP and into the 60-minute recovery period, while a third factor (knee loading) decreased only during the recovery period (P ≤ 0.05). Conclusion: The individualized sport-specific IEP may have more subtle effects on landing biomechanics when compared with short-term, exhaustive fatigue protocols. Clinical Relevance: Potentially injurious landing biomechanics may not occur until the later stages of soccer activity. PMID:24587862

  10. Statistical model for degraded DNA samples and adjusted probabilities for allelic drop-out

    DEFF Research Database (Denmark)

    Tvedebrink, Torben; Eriksen, Poul Svante; Mogensen, Helle Smidt

    2012-01-01

    Abstract DNA samples found at a scene of crime or obtained from the debris of a mass disaster accident are often subject to degradation. When using the STR DNA technology, the DNA profile is observed via a so-called electropherogram (EPG), where the alleles are identified as signal peaks above...... a certain level or above a signal to noise threshold. Degradation implies that these peak intensities decrease in strength for longer short tandem repeat (STR) sequences. Consequently, long STR loci may fail to produce peak heights above the limit of detection resulting in allelic or locus drop......-outs. In this paper, we present a method for measuring the degree of degradation of a sample and demonstrate how to incorporate this in estimating the probability of allelic drop-out. This is done by extending an existing method derived for non-degraded samples. The performance of the methodology is evaluated using...

  11. Statistical model for degraded DNA samples and adjusted probabilities for allelic drop-out

    DEFF Research Database (Denmark)

    Tvedebrink, Torben; Eriksen, Poul Svante; Mogensen, Helle Smidt

    2012-01-01

    DNA samples found at a scene of crime or obtained from the debris of a mass disaster accident are often subject to degradation. When using the STR DNA technology, the DNA profile is observed via a so-called electropherogram (EPG), where the alleles are identified as signal peaks above a certain...... level or above a signal to noise threshold. Degradation implies that these peak intensities decrease in strength for longer short tandem repeat (STR) sequences. Consequently, long STR loci may fail to produce peak heights above the limit of detection resulting in allelic or locus drop......-outs. In this paper, we present a method for measuring the degree of degradation of a sample and demonstrate how to incorporate this in estimating the probability of allelic drop-out. This is done by extending an existing method derived for non-degraded samples. The performance of the methodology is evaluated using...

  12. Models optimization for the pressure drop calculation in two-phase flow cooled bundle

    International Nuclear Information System (INIS)

    Ladeira, L.C.D.; Rezende, H.C.

    1994-01-01

    The analysis of two-phase tests, performed in a mock-up of nuclear fuel element, to verify the applicability of existing calculation models to determine the pressure drop is presented. The tests were performed using Reynolds Number in the range from 4 x 10 4 to 1.6 x 10 5 , with heat flux up to 105 W/cm 2 , and three different levels of pressure: 2.0, 6.0 and 10.0 bar. The tests results were used to optimize the bubble detaching point in two correlations (Bowing and Lelouche-Zolotar) in order to obtain the subcooled void fraction. Comparison between measured and calculated results has shown that the pressure drop,in 96% of the tests, was reproduced within +- 16% when using the Bowing correlation, and +- 9% with the Lellouche-Zolotar one. (author)

  13. Crash Simulation of a Boeing 737 Fuselage Section Vertical Drop Test

    Science.gov (United States)

    Fasanella, Edwin L.; Jackson, Karen E.; Jones, Yvonne T.; Frings, Gary; Vu, Tong

    2004-01-01

    A 30-ft/s vertical drop test of a fuselage section of a Boeing 737 aircraft was conducted in October of 1999 at the FAA Technical Center in Atlantic City, NJ. This test was performed to evaluate the structural integrity of a conformable auxiliary fuel tank mounted beneath the floor and to determine its effect on the impact response of the airframe structure and the occupants. The test data were used to compare with a finite element simulation of the fuselage structure and to gain a better understanding of the impact physics through analytical/experimental correlation. To perform this simulation, a full-scale 3-dimensional finite element model of the fuselage section was developed using the explicit, nonlinear transient-dynamic finite element code, MSC.Dytran. The emphasis of the simulation was to predict the structural deformation and floor-level acceleration responses obtained from the drop test of the B737 fuselage section with the auxiliary fuel tank.

  14. Characteristics of patients in an eating disorder sample who dropped out: 2-year follow-up.

    Science.gov (United States)

    Gómez Del Barrio, Andrés; Vellisca Gonzalez, María Yolanda; González Gómez, Jana; Latorre Marín, José Ignacio; Carral-Fernández, Laura; Orejudo Hernandez, Santos; Madrazo Río-Hortega, Inés; Moreno Malfaz, Laura

    2017-07-17

    This manuscript explores the characteristics of individuals diagnosed with an eating disorder who dropped out of treatment, compared with those who completed it. The participants were 196 patients diagnosed with eating disorders (according to DSM-IV-TR criteria) who consecutively began treatment for the first time in an eating disorders unit. They were assessed at baseline with a set of questionnaires evaluating eating habits, temperament, and general psychopathology. During the follow-up period, patients who dropped out were re-assessed via a telephone interview. In the course of a 2-year follow-up, a total of 80 (40.8%) patients were labeled as dropouts, and 116 (59.2%) remaining subjects were considered completers. High TCI scores in the character dimensions of Disorderliness (NS4) (p out of treatment. Level III: Cohort Study.

  15. Green chemistry and nanofabrication in a levitated Leidenfrost drop

    Science.gov (United States)

    Abdelaziz, Ramzy; Disci-Zayed, Duygu; Hedayati, Mehdi Keshavarz; Pöhls, Jan-Hendrik; Zillohu, Ahnaf Usman; Erkartal, Burak; Chakravadhanula, Venkata Sai Kiran; Duppel, Viola; Kienle, Lorenz; Elbahri, Mady

    2013-10-01

    Green nanotechnology focuses on the development of new and sustainable methods of creating nanoparticles, their localized assembly and integration into useful systems and devices in a cost-effective, simple and eco-friendly manner. Here we present our experimental findings on the use of the Leidenfrost drop as an overheated and charged green chemical reactor. Employing a droplet of aqueous solution on hot substrates, this method is capable of fabricating nanoparticles, creating nanoscale coatings on complex objects and designing porous metal in suspension and foam form, all in a levitated Leidenfrost drop. As examples of the potential applications of the Leidenfrost drop, fabrication of nanoporous black gold as a plasmonic wideband superabsorber, and synthesis of superhydrophilic and thermal resistive metal-polymer hybrid foams are demonstrated. We believe that the presented nanofabrication method may be a promising strategy towards the sustainable production of functional nanomaterials.

  16. Structural concerns in dynamic drop loads on transfer lock mechanisms

    International Nuclear Information System (INIS)

    Pfeiffer, P.A.; Moran, T.J.; Kulak, R.F.

    1997-01-01

    Drop loads are usually low probability events that can generate substantial loading to the impacted structures. When the impacted structure contains slender elements, the concern about dynamic buckling must be addressed. The problem of interest here is a structure is also under significant preload, which must be taken into account in the transient analysis. For complex structures, numerical simulations are the only viable option for assessing the transient response to short duration impactive loads. this paper addresses several analysis issues of preloaded structures with slender members subjected to drop loads. A three-dimensional beam element is validated for use in dynamic buckling analysis. the numerical algorithm used to solve the transient response of preloaded structures is discussed. The methodology is applied to an inter-compartment lock that is under significant preloads, and subjected to a drop load

  17. Playing with water drops: from wetting to optics through electrostatics

    International Nuclear Information System (INIS)

    Domps, A; Roques-Carmes, T

    2011-01-01

    We present a consistent series of activities, including experiments and basic computational studies, investigating the shape and optical properties of water drops in connection with novel technological devices. Most of the work can be carried out with simple teaching equipment and is well suited to undergraduate students. Firstly, we show how the mass variations of a sessile drop can be used to control its curvature and hence to produce lenses with tunable focal distance. Alternatively, the shape of the drop can be varied using electrowetting on dielectric (EWOD). We propose a simple pedagogical approach to this phenomenon in connection with historical electrostatic apparatus. A detailed process for the preparation of an EWOD device is given, together with a focimetric method allowing the analysis of electrowetting effects in practical exercises. Finally, the manipulations of a commercialized variable focus lens illustrate that EWOD is at the heart of most recent technological developments, making practical work in optics more attractive than traditional exercises using conventional lenses.

  18. Green chemistry and nanofabrication in a levitated Leidenfrost drop.

    Science.gov (United States)

    Abdelaziz, Ramzy; Disci-Zayed, Duygu; Hedayati, Mehdi Keshavarz; Pöhls, Jan-Hendrik; Zillohu, Ahnaf Usman; Erkartal, Burak; Chakravadhanula, Venkata Sai Kiran; Duppel, Viola; Kienle, Lorenz; Elbahri, Mady

    2013-01-01

    Green nanotechnology focuses on the development of new and sustainable methods of creating nanoparticles, their localized assembly and integration into useful systems and devices in a cost-effective, simple and eco-friendly manner. Here we present our experimental findings on the use of the Leidenfrost drop as an overheated and charged green chemical reactor. Employing a droplet of aqueous solution on hot substrates, this method is capable of fabricating nanoparticles, creating nanoscale coatings on complex objects and designing porous metal in suspension and foam form, all in a levitated Leidenfrost drop. As examples of the potential applications of the Leidenfrost drop, fabrication of nanoporous black gold as a plasmonic wideband superabsorber, and synthesis of superhydrophilic and thermal resistive metal-polymer hybrid foams are demonstrated. We believe that the presented nanofabrication method may be a promising strategy towards the sustainable production of functional nanomaterials.

  19. Colloidal assembly in Leidenfrost drops for noniridescent structural color pigments.

    Science.gov (United States)

    Lim, Che Ho; Kang, Hyelim; Kim, Shin-Hyun

    2014-07-22

    Noniridescent structural color pigments have great potential as alternatives to conventional chemical color pigments in many coloration applications due to their nonbleaching and color-tunable properties. In this work, we report a novel method to create photonic microgranules composed of glassy packing of silica particles and small fraction of carbon black nanoparticles, which show pronounced structural colors with low angle-dependency. To prepare isotropic random packing in each microgranule, a Leidenfrost drop, which is a drop levitated by its own vapor on a hot surface, is employed as a template for fast consolidation of silica particles. The drop randomly migrates over the hot surface and rapidly shrinks, while maintaining its spherical shape, thereby consolidating silica particles to granular structures. Carbon black nanoparticles incorporated in the microgranules suppress incoherent multiple scattering, thereby providing improved color contrast. Therefore, photonic microgranules in a full visible range can be prepared by adjusting the size of silica particles with insignificant whitening.

  20. A Partial Equilibrium Theory for Drops and Capillary Liquids

    International Nuclear Information System (INIS)

    Searcy, Alan W.; Beruto, Dario T.; Barberis, Fabrizio

    2006-01-01

    The two-century old theory of Young and Laplace retains a powerful influence on surface and interface studies because it quantitatively predicts the height of rise of capillary liquids from the contact angles of drops. But the classical theory does not acknowledge that equilibrium requires separate minimization of partial free energies of one-component liquids bonded to immiscible solids. We generalize a theorem of Gibbs and Curie to obtain a partial equilibrium (PE) theory that does so and that also predicts the height of capillary rise from contact angles of drops. Published observations and our own measurements of contact angles of water bonded to glass and Teflon surfaces support the conclusion of PE theory that contact angles of meniscuses and of drops are different dependent variables. PE theory provides thermodynamic and kinetic guidance to nanoscale processes that the classical theory obscures, as illustrated by examples in our concluding section