WorldWideScience

Sample records for block copolymer thin

  1. Asymmetric block copolymers confined in a thin film

    NARCIS (Netherlands)

    Huinink, HP; Brokken-Zijp, JCM; van Dijk, MA; Sevink, GJA

    2000-01-01

    We have used a dynamic density functional theory (DDFT) for polymeric systems, to simulate the formation of micro phases in a melt of an asymmetric block copolymer, A(n)B(m)(f(A) = 1/3), both in the bulk and in a thin film. In the DDFT model a polymer is represented as a chain of springs and beads.

  2. Direct Immersion Annealing (DIA) of Block Copolymer Thin Film

    Science.gov (United States)

    Modi, Arvind; Karim, Alamgir

    2014-03-01

    Solvent Vapor Annealing (SVA) methodologies of block copolymer (BCP) films have demonstrated excellent potential for control of nanostructures and morphologies. However, SVA designs require sophisticated instrumentation, and fine control of system parameters in batch processing mode which is relatively complex and limits its feasibility. We developed a faster and robust solvent immersion strategy for microphase separation and nanostructure control of as-cast BCP thin films with minimal sophistication. Our Direct Immersion Annealing (DIA) method requires immersion in a mixture of non-solvent and good solvent (for BCP) for annealing. A non-solvent component prevents dissolution of the film resting on substrate while a good solvent percolates through the film, plasticizes it, and shifts glass-transition below room temperature leading to microphase separation and ordering. Our study of PS-PMMA system demonstrates that a robust control over thin film ordering and transient swelling could be achieved through a fine control of solubility parameter of solvent mixture and temperature with no dead-time. Further, we exhibit the utility of DIA for alignment of BCP domains on topographically patterned substrates. University of Akron Research Foundation (UARF).

  3. Defect motion and annihilation in block copolymer thin films

    Science.gov (United States)

    Mueller, Marcus; Li, Weihua

    2015-03-01

    Using self-consistent field theory and computer simulation of a soft, coarse-grained particle model we study defect motion and annihilation in thin films of lamella-forming block copolymers on neutral and chemically patterned substrates. By virtue of the strain-field mediated interactions, dislocation defects with opposite orientation move towards each other. This motion depends both on the thermodynamic, strain-field mediated driving force and the single-chain dynamics that is required to alter the morphology and reduce the distance between the defect cores. This interplay results in a qualitative dependence of the time evolution on the topology of the defect morphology. Upon collision of the defects, they either spontaneously annihilate or form a metastable, tight defect pair. In the latter case, a free-energy barrier has to be overcome to finally produce a defect-free structure. Computing the minimum free-energy path within self-consistent field theory we investigate the dependence of the free-energy barriers of defect motion and annihilation on incompatibility, strength of the chemical surface pattern, and defect morphology. European Union FP7 / GA No. 619793 CoLiSA.MMP.

  4. Thin block copolymer films : film formation and corrugation under the AFM tip

    NARCIS (Netherlands)

    Maas, J.H.; Cohen Stuart, M.A.; Fleer, G.J.

    2000-01-01

    The tip of an atomic force microscope was used to induce nanoscale ordering in thin films of polystyrene-poly(4-vinyl pyridine) block copolymers under low force. The AFM tip produces rims on a mesoscopic scale oriented perpendicularly to the scanning direction. A wide range of molecular weights of b

  5. PS-b-PDMS Block Copolymer Thin Film: Pattern Formation and Phase Behavior

    Science.gov (United States)

    Hsieh, I.-Fan; Cheng, Stephen Z. D.; Department of Polymer Science, The University of Akron Team

    2011-03-01

    Recently, block copolymer thin films attract great attention due to their potential applications in surface nano-lithography. In our work, PS- b -PDMS with cylinder morphology is chosen due to extremely large χ value between two blocks. Besides, PS- b -PDMS can be transformed into silicon oxide under UV/O3 exposure and a layer of silicon oxide with the self-assembled block copolymer patterns can be made. By utilizing the PGMEA as solvent, we can easily obtain sphere morphology in cylindrical composition block copolymer by preserved block copolymer solution morphology during film formation. Furthermore, in thermal annealing process, the phase behavior of the PS- b -PDMS thin film is strongly affects by molecular weight, film thickness and annealing temperature. In larger-molecular-weight PS- b -PDMS, we only observed spherical domains rearrangement and without morphology transition between sphere and cylinder due to high energy barrier, whereas, in the case of smaller-molecular-weight polymer, depending on the film thickness and annealing temperature, its thin film morphology transits between sphere and cylinder alternatively, which is similar to what we found in solvent annealing.

  6. Vertically oriented hexagonal mesoporous zirconia thin films by block copolymer templating

    OpenAIRE

    Miko, Annamaria ; Demirel, A. Levent ; Somer, Mehmet

    2012-01-01

    We report the synthesis of vertically oriented, long-range ordered hexagonal mesoporous zirconia thin ?lms. The orientation of hexagonally ordered cylindrical mesopores in thin ?lms was effectively controlled by taking advantage of the temperature dependent hydrophobicity of the templating block copolymer PEO–PPO–PEO. Vertical orientation was obtained when temperature was 30 C or above throughout the process. Dehydration and enhanced chemical incompatibility between the PEO and PPO b...

  7. Highly ordered palladium nanodots and nanowires from switchable block copolymer thin films

    Energy Technology Data Exchange (ETDEWEB)

    Bhoje Gowd, E; Nandan, Bhanu; Vyas, Mukesh Kumar; Stamm, Manfred [Leibniz Institute of Polymer Research Dresden, Hohe Strasse 6, 01069, Dresden (Germany); Bigall, Nadja C; Eychmueller, Alexander [Physical Chemistry and Electrochemistry, TU Dresden, Bergstrasse 66b, 01062, Dresden (Germany); Schloerb, Heike, E-mail: gowd@ipfdd.d, E-mail: nandan@ipfdd.d [Leibniz Institute for Solid State and Materials Research Dresden, PO Box 27 00 16, D-01171, Dresden (Germany)

    2009-10-14

    We demonstrate a new approach to fabricate highly ordered arrays of nanoscopic palladium dots and wires using switchable block copolymer thin films. The surface-reconstructed block copolymer templates were directly deposited with palladium nanoparticles from a simple aqueous solution. The preferential interaction of the nanoparticles with one of the blocks is mainly responsible for the lateral arrangement of the nanoparticles inside the pores of the templates in addition to the capillary forces. A subsequent stabilization by UV-irradiation followed by pyrolysis in air at 450 {sup 0}C removes the polymer to produce highly ordered metallic nanostructures. We extended this approach to micellar films to obtain metallic nanostructures. This method is highly versatile as the procedure used here is simple, eco-friendly and provides a simple approach to fabricate a broad range of nanoscaled architectures with tunable lateral spacing, and can be extended to systems with even smaller dimensions.

  8. Pattern formation and phase behavior in PS-B-Si containing block copolymer thin film

    Science.gov (United States)

    Hsieh, I.-Fan

    Since the top-down approaches, such as the extremely ultraviolet (EUV) technique and the high-index fluid-based immersion ArF lithography, may be cover one or two generations, these lithography technologies are getting more severe for the feature size scaling down to sub 10 nm. The directed self-assembly technology of block copolymers is one of the candidates for next generation lithography which can afford feature sizes that are dictated by the molecular weight of the block copolymer and are typically 15 to 30 nm. Directed self-assembly of block copolymers has attracted attention as a technology to extend photoresist-based lithography to smaller dimensions. It has been demonstrated that the directed self assembly of block copolymer offers a new route to perfect nanolithographic pattering at sub-50 nm length scale with molecular scale precision. For application in electronic media, it requires large-area, long-range ordered structures, which is both a kinetic and thermodynamic problem and requires subtle balance of various parameters and processing conditions. So far, block copolymer thin films have already achieved certain success, mainly with higher molecular weights and a feature size of ˜30 nm. Several challenges still remain, such as (a) the generation of long-range ordered structure with smaller feature sizes (domain size block copolymers have emerged as next generation block copolymers for nanolithography. Their films can be processed under dry conditions using oxygen plasma to produce inorganic, silica patterns which enables their integration into existing device fabrication. Also, the large thermodynamic incompatibility of silicon-containing polymers with other organic polymers is favorable for patterns with small domains sizes, large correlation lengths, and low interfacial roughness. In PS-b-PDMS system, a solvent-induced spherical structure was obtained and stabilized by preparing both the bulk and thin film from propylene glycol methyl ether acetate

  9. Thin Isoporous Block Copolymer Membranes: It Is All about the Process.

    Science.gov (United States)

    Hahn, Janina; Clodt, Juliana I; Abetz, Clarissa; Filiz, Volkan; Abetz, Volker

    2015-09-30

    The combination of the self-assembly of amphiphilic block copolymers and the nonsolvent induced phase inversion process offers an efficient way to isoporous integral-asymmetric membranes. In this context we report fast, easily upscalable and material reducing ways to thin self-assembled membranes. Therefore, we succeeded to implement a spray or dip coating step into the membrane formation process of different diblock copolymers like polystyrene-block-poly(4-vinylpyridine), poly(α-methylstyrene)-bock-poly(4-vinylpyridine), and polystyrene-block-poly(iso-propylglycidyl methacrylate). The formation of hexagonal pore structures was possible using a highly diluted one solvent system allowing the reduction of diblock copolymer consumption and therefore the production costs are minimized compared to conventional blade casting approaches. The broad applicability of the process was proven by using different flat and hollow fiber support materials. Furthermore, the membranes made by this new method showed a more than 6-fold increase in water flux compared to conventional polystyrene-block-poly(4-vinylpyridine) membranes with similar pore sizes prepared by blade casting. The membranes could be proven to be stable at transmembrane pressures of 2 bar and showed a pH responsive flux behavior over several cycles. PMID:26349610

  10. Laser processing of polyethylene glycol derivative and block copolymer thin films

    Energy Technology Data Exchange (ETDEWEB)

    Cristescu, R. [National Institute for Laser, Plasma and Radiation Physics, MG-36, RO-77125, Bucharest (Romania)], E-mail: rodica.cristescu@inflpr.ro; Popescu, C.; Popescu, A.C.; Grigorescu, S.; Duta, L.; Mihailescu, I.N. [National Institute for Laser, Plasma and Radiation Physics, MG-36, RO-77125, Bucharest (Romania); Andronie, A.; Stamatin, I. [University of Bucharest, 3Nano-SAE Research Center, P.O. Box MG-11, Bucharest-Magurele (Romania); Ionescu, O.S.; Mihaiescu, D. [University of Agriculture Sciences and Veterinary Medicine, 59 Marasti, Bucharest (Romania); Buruiana, T. [Petru Poni Institute of Macromolecular Chemistry, Aleea Grigore Ghica Voda, 41A, Iasi (Romania); Chrisey, D.B. [Rensselaer Polytechnic Institute, Department of Material Science, 110 8th Street, Troy, NY 12180-3590 (United States)

    2009-03-01

    We report the deposition by MAPLE of: (i) a novel polyethylene glycol derivative with carboxyl functional groups and (ii) a block copolymer: poly(ethylene glycol)methyl ether-block-poly(caprolactone)-block-poly(ethylene glycol)methyl ether. We used a KrF* excimer laser source ({lambda} = 248 nm, {tau} = 25 ns, {nu} = 5 Hz). The laser fluence was set within the 200-700 mJ/cm{sup 2} range. The deposited thin films have been investigated by FTIR and AFM. We have concluded that the main functional groups of starting materials are present in the transferred film. We also examined the influence of laser fluence on both thin film structure and morphology.

  11. Laser processing of polyethylene glycol derivative and block copolymer thin films

    International Nuclear Information System (INIS)

    We report the deposition by MAPLE of: (i) a novel polyethylene glycol derivative with carboxyl functional groups and (ii) a block copolymer: poly(ethylene glycol)methyl ether-block-poly(caprolactone)-block-poly(ethylene glycol)methyl ether. We used a KrF* excimer laser source (λ = 248 nm, τ = 25 ns, ν = 5 Hz). The laser fluence was set within the 200-700 mJ/cm2 range. The deposited thin films have been investigated by FTIR and AFM. We have concluded that the main functional groups of starting materials are present in the transferred film. We also examined the influence of laser fluence on both thin film structure and morphology

  12. Synergistic templated self-assembly of cellulose nanocrystals in thin block copolymer films

    Science.gov (United States)

    Grolman, Danielle; Gilman, Jeffrey; Davis, Chelsea; Karim, Alamgir

    2015-03-01

    Nanofillers in thin polymer films offer unique advantage to potentially modify the film's thermal, optical, electrical and mechanical properties due to the high surface area to volume ratio and intrinsic property change at the nanoscale. Nanofilled polymer films have been shown to exhibit unusual film stability to dewetting with a nonmonotonic behavior with nanofiller loading, potentially arising from factors such as competitive phase behavior and filler aggregation, particularly in the high nanofiller concentration limit. In this regard, block copolymer films can act as ideal nanoscale structured templates to selectively sequester and organize nanofillers. In conjunction with incorporated cellulose nanocrystals (CNCs), we seek to understand how individual anisotropic nanofillers can provide synergistic reinforcement to inherently anisotropic nanostructured block copolymer films. A clear enhancement in the Young's Modulus was observed with increased CNC loading using strain-induced elastic buckling instability for mechanical measurements (SIEBIMM) for thin films. To this end, we examine the nanoscale to microscale morphology of the blend film through AFM, TEM and grazing incidence small-angle x-ray scattering (GISAXS), and CNC dispersion and percolation through high-intensity grazing incidence wide-angle x-ray scattering (GIWAXS) analysis.

  13. Directed self-assembly of block copolymer films on atomically-thin graphene chemical patterns.

    Science.gov (United States)

    Chang, Tzu-Hsuan; Xiong, Shisheng; Jacobberger, Robert M; Mikael, Solomon; Suh, Hyo Seon; Liu, Chi-Chun; Geng, Dalong; Wang, Xudong; Arnold, Michael S; Ma, Zhenqiang; Nealey, Paul F

    2016-01-01

    Directed self-assembly of block copolymers is a scalable method to fabricate well-ordered patterns over the wafer scale with feature sizes below the resolution of conventional lithography. Typically, lithographically-defined prepatterns with varying chemical contrast are used to rationally guide the assembly of block copolymers. The directed self-assembly to obtain accurate registration and alignment is largely influenced by the assembly kinetics. Furthermore, a considerably broad processing window is favored for industrial manufacturing. Using an atomically-thin layer of graphene on germanium, after two simple processing steps, we create a novel chemical pattern to direct the assembly of polystyrene-block-poly(methyl methacrylate). Faster assembly kinetics are observed on graphene/germanium chemical patterns than on conventional chemical patterns based on polymer mats and brushes. This new chemical pattern allows for assembly on a wide range of guiding periods and along designed 90° bending structures. We also achieve density multiplication by a factor of 10, greatly enhancing the pattern resolution. The rapid assembly kinetics, minimal topography, and broad processing window demonstrate the advantages of inorganic chemical patterns composed of hard surfaces. PMID:27528258

  14. Thin polymer films of block copolymers and blend/nanoparticle composites

    Science.gov (United States)

    Kalloudis, Michail

    In this thesis, atomic force microscopy (AFM), transmission electron microscopy (TEM) and optical microscopy techniques were used to investigate systematically the self-assembled nanostructure behaviour of two different types of spin-cast polymer thin films: poly(isoprene-b-ethylene oxide), PI-b-PEO diblock copolymers and [poly(9,9-dioctylfluorene-co-benzothiadiazole)]:poly[9,9- dioctyfluorene-co-N-(4-butylphenyl)-diphenylamine], F8BT:TFB conjugated polymer blends. In the particular case of the polymer blend thin films, the morphology of their composites with cadmium selenide (CdSe) quantum dot (QD) nanoparticles was also investigated. For the diblock copolymer thin films, the behaviour of the nanostructures formed and the wetting behaviour on mica, varying the volume fraction of the PEO block (fPEO) and the average film thickness was explored. For the polymer blend films, the effect of the F8BT/TFB blend ratio (per weight), spin-coating parameters and solution concentration on the phase-separated nanodomains was investigated. The influence of the quantum dots on the phase separation when these were embedded in the F8BT:TFB thin films was also examined. It was found that in the case of PI-b-PEO copolymer thin films, robust nanostructures, which remained unchanged after heating/annealing and/or ageing, were obtained immediately after spin coating on hydrophilic mica substrates from aqueous solutions. The competition and coupling of the PEO crystallisation and the phase separation between the PEO and PI blocks determined the ultimate morphology of the thin films. Due to the great biocompatible properties of the PEO block (protein resistance), robust PEO-based nanostructures find important applications in the development of micro/nano patterns for biological and biomedical applications. It was also found that sub-micrometre length-scale phase-separated domains were formed in F8BT:TFB spin cast thin films. The nanophase-separated domains of F8BT-rich and TFB-rich areas

  15. Manipulating block copolymer self-assemblies in bulk and thin films by thermal and solvent annealing

    Science.gov (United States)

    Gu, Weiyin

    The self--assembly of block copolymers (BCPs) into well--ordered nanoscopic arrays holds promise for new technological breakthroughs as templates and scaffolds for the fabrication of nanostructured materials. It is essential to establish convenient approaches to control the morphology of BCPs, since some applications require addressability, the BCP microdomains must be perfectly aligned and oriented. The theme of this thesis is the use of external forces, specifically thermal and solvent annealing, to guide the self--assembly of BCPs to obtain microphase separated morphologies for different applications. Three representative BCP systems, having lamellar, cylindrical and spherical microdomains are discussed. First, the self--assembly of lamella--forming brush block copolymers (BrBCPs) having polylactide (PLA) and polystyrene (PS) side chains were studied in the bulk and in thin films. The domain size increased approximately linearly with the molecular weight of the backbone, which indicated that the backbone was in an extended conformation that was confirmed theoretically. In situ small angle x--ray scattering (SAXS) measurements indicated that the self--assembly of the BrBCPs was quite rapid, due to the rigid nature of the backbone chain, Second, the directed self--assembly of cylinder--forming polystyrene--block--poly(ethylene oxide)s (PS--b--PEOs) in thin films were investigated. The polymer--surface interactions were tuned by hydroxyl end--functionalized polymers, so that the orientation of the PS--b--PEO microdomains was controlled during thermal annealing. Cylindrical PEO microdomains embedded in a PS matrix orientated normal to the silicon substrates were observed over a wide processing window when the substrates were modified by PS-- b--PEO BCPs. PS--b--PEOs with an o--nitrobenzyl ester junction point (PS--hnu --PEOs) were used to fabricate nanoscopic dot and line patterns having long--range lateral order. The cylindrical BCP microdomains were oriented

  16. Continuous and patterned deposition of functional block copolymer thin films using electrospray

    Science.gov (United States)

    Toth, Kristof; Hu, Hanqiong; Kim, Myungwoong; Gopalan, Padma; Loewenberg, Michael; Osuji, Chinedum

    The delivery of sub-micron droplets of dilute polymer solutions to a heated substrate by electrospray deposition (ESD) enables precisely controlled and continuous growth of block copolymer (BCP) thin films. The ESD process overcomes many shortcomings of spin coating deposition, including the batch nature of the process, loss of potentially valuable polymer, limitations of solvent choice, and large time scales of annealing. We report that high substrate temperatures led to vertically oriented cylindrical microdomains of poly(styrene-block-methyl methacrylate) (PS-b-PMMA) at the film surface independent of the solvent composition and deposition rates utilized. Conversely, low substrate temperatures resulted in morphologies that were more sensitive to these parameters, with poorly ordered films of globular structures. We also report on the new possibility for patterned deposition of BCP films by spatially varying the electric field at the substrate using an underlying charged grid. To overcome surface charging, a novel alternating current electrospray process is proposed for deposition on non-conductive surfaces.

  17. Bactericidal block copolymer micelles.

    Science.gov (United States)

    Vyhnalkova, Renata; Eisenberg, Adi; van de Ven, Theo

    2011-05-12

    Block copolymer micelles with bactericidal properties were designed to deactivate pathogens such as E. coli bacteria. The micelles of PS-b-PAA and PS-b-P4VP block copolymers were loaded with biocides TCMTB or TCN up to 20 or 30 wt.-%, depending on the type of antibacterial agent. Bacteria were exposed to loaded micelles and bacterial deactivation was evaluated. The micelles loaded with TCN are bactericidal; bacteria are killed in less than two minutes of exposure. The most likely interpretation of the data is that the biocide is transferred to the bacteria by repeated micelle/bacteria contacts, and not via the solution. PMID:21275041

  18. Block copolymer battery separator

    Energy Technology Data Exchange (ETDEWEB)

    Wong, David; Balsara, Nitash Pervez

    2016-04-26

    The invention herein described is the use of a block copolymer/homopolymer blend for creating nanoporous materials for transport applications. Specifically, this is demonstrated by using the block copolymer poly(styrene-block-ethylene-block-styrene) (SES) and blending it with homopolymer polystyrene (PS). After blending the polymers, a film is cast, and the film is submerged in tetrahydrofuran, which removes the PS. This creates a nanoporous polymer film, whereby the holes are lined with PS. Control of morphology of the system is achieved by manipulating the amount of PS added and the relative size of the PS added. The porous nature of these films was demonstrated by measuring the ionic conductivity in a traditional battery electrolyte, 1M LiPF.sub.6 in EC/DEC (1:1 v/v) using AC impedance spectroscopy and comparing these results to commercially available battery separators.

  19. New poly(dimethylsiloxane)/poly(perfluorooctylethyl acrylate) block copolymers: structure and order across multiple length scales in thin films

    KAUST Repository

    Martinelli, Elisa

    2011-01-01

    Three sets of a new class of low surface tension block copolymers were synthesized consisting of a poly(dimethylsiloxane) (PDMS) block and a poly(perfluorooctylethyl acrylate) (AF8) block. The polymers were prepared using a bromo-terminated PDMS macroinitiator, to which was attached an AF8 block grown using atom transfer radical polymerization (ATRP) in such a designed way that the molecular weight and composition of the two polymer blocks were regularly varied. The interplay of both the phase separated microstructure and the mesomorphic character of the fluorinated domains with their effect on surface structure was evaluated using a suite of analytical tools. Surfaces of spin-coated and thermally annealed films were assessed using a combination of X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure (NEXAFS) studies. Both atomic force microscopy (AFM) measurements and grazing incidence small angle X-ray scattering (GISAXS) studies were carried out to evaluate the microstructure of the thin films. Even in block copolymers in which the PDMS block was the majority component, a significant presence of the lower surface energy AF8 block was detected at the film surface. Moreover, the perfluorooctyl helices of the AF8 repeat units were highly oriented at the surface in an ordered, tilted smectic structure, which was compared with those of the bulk powder samples using wide-angle X-ray powder diffraction (WAXD) studies. © 2011 The Royal Society of Chemistry.

  20. Thin polymer films of block copolymers and blend/nanoparticle composites

    OpenAIRE

    Kalloudis, Michail

    2013-01-01

    In this thesis, atomic force microscopy (AFM), transmission electron microscopy (TEM) and optical microscopy techniques were used to investigate systematically the self-assembled nanostructure behaviour of two different types of spin-cast polymer thin films: poly(isoprene-b-ethylene oxide), PI-b-PEO diblock copolymers and [poly(9,9-dioctylfluorene-co-benzothiadiazole)]:poly[9,9- dioctyfluorene-co-N-(4-butylphenyl)-diphenylamine], F8BT:TFB conjugated polymer blends. In the pa...

  1. NANOSTRUCTURES OF FUNCTIONAL BLOCK COPOLYMERS

    Institute of Scientific and Technical Information of China (English)

    Guojun Liu

    2000-01-01

    Nanostructure fabrication from block copolymers in my group normally involves polymer design, synthesis, selfassembly, selective domain crosslinking, and sometimes selective domain removal. Preparation of thin films with nanochannels was used to illustrate the strategy we took. In this particular case, a linear triblock copolymer polyisopreneblock-poly(2-cinnamoylethyl methacrylate)-block-poly(t-butyl acrylate), PI-b-PCEMA-b-PtBA, was used. Films, 25 to50μm thick, were prepared from casting on glass slides a toluene solution of PI-b-PCEMA-b-PtBA and PtBA homopolymer,hPtBA, where hPtBA is shorter than the PtBA block. At the hPtBA mass fraction of 20% relative to the triblock or the total PtBA (hPtBA and PtBA block) volume fraction of 0.44, hPtBA and PtBA formed a seemingly continuous phase in the matrix of PCEMA and PI. Such a block segregation pattern was locked in by photocrosslinking the PCEMA domain. Nanochannels were formed by extracting out hPtBA with solvent. Alternatively, larger channels were obtained from extracting out hPtBA and hydrolyzing the t-butyl groups of the PtBA block. Such membranes were not liquid permeable but had gas permeability constants ~6 orders of magnitude higher than that of low-density polyethylene films.

  2. Analysis of Order Formation in Block Copolymer Thin Films UsingResonant Soft X-Ray Scattering

    Energy Technology Data Exchange (ETDEWEB)

    Virgili, Justin M.; Tao, Yuefei; Kortright, Jeffrey B.; Balsara,Nitash P.; Segalman, Rachel A.

    2006-11-27

    The lateral order of poly(styrene-block-isoprene) copolymer(PS-b-PI) thin films is characterized by the emerging technique ofresonant soft X-ray scattering (RSOXS) at the carbon K edge and comparedto ordering in bulk samples of the same materials measured usingconventional small-angle X-ray scattering. We show resonance using theoryand experiment that the loss of scattering intensity expected with adecrease in sample volume in the case of thin films can be overcome bytuning X-rays to the pi* resonance of PS or PI. Using RSOXS, we study themicrophase ordering of cylinder- and phere-forming PS-b-PI thin films andcompare these results to position space data obtained by atomic forcemicroscopy. Our ability to examine large sample areas (~;9000 mu m2) byRSOXS enables unambiguous identification of the lateral lattice structurein the thin films. In the case of the sphere-forming copolymer thin film,where the spheres are hexagonally arranged, the average sphere-to-spherespacing is between the bulk (body-centered cubic) nearest neighbor andbulk unit cell spacings. In the case of the cylinder-forming copolymerthin film, the cylinder-to-cylinder spacing is within experimental errorof that obtained in the bulk.

  3. Interfaces between Block Copolymer Domains

    Science.gov (United States)

    Kim, Jaeup; Jeong, Seong-Jun; Kim, Sang Ouk

    2011-03-01

    Block copolymers naturally form nanometer scale structures which repeat their geometry on a larger scale. Such a small scale periodic pattern can be used for various applications such as storage media, nano-circuits and optical filters. However, perfect alignment of block copolymer domains in the macroscopic scale is still a distant dream. The nanostructure formation usually occurs with spontaneously broken symmetry; hence it is easily infected by topological defects which sneak in due to entropic fluctuation and incomplete annealing. Careful annealing can gradually reduce the number of defects, but once kinetically trapped, it is extremely difficult to remove all the defects. One of the main reasons is that the defect finds a locally metastable morphology whose potential depth is large enough to prohibit further morphology evolution. In this work, the domain boundaries between differently oriented lamellar structures in thin film are studied. For the first time, it became possible to quantitatively study the block copolymer morphology in the transitional region, and it was shown that the twisted grain boundary is energetically favorable compared to the T-junction grain boundary. [Nano Letters, 9, 2300 (2010)]. This theoretical method successfully explained the experimental results.

  4. Chemical Interactions and Their Role in the Microphase Separation of Block Copolymer Thin Films

    Directory of Open Access Journals (Sweden)

    Richard A. Farrell

    2009-08-01

    Full Text Available The thermodynamics of self-assembling systems are discussed in terms of the chemical interactions and the intermolecular forces between species. It is clear that there are both theoretical and practical limitations on the dimensions and the structural regularity of these systems. These considerations are made with reference to the microphase separation that occurs in block copolymer (BCP systems. BCP systems self-assemble via a thermodynamic driven process where chemical dis-affinity between the blocks driving them part is balanced by a restorative force deriving from the chemical bond between the blocks. These systems are attracting much interest because of their possible role in nanoelectronic fabrication. This form of self-assembly can obtain highly regular nanopatterns in certain circumstances where the orientation and alignment of chemically distinct blocks can be guided through molecular interactions between the polymer and the surrounding interfaces. However, for this to be possible, great care must be taken to properly engineer the interactions between the surfaces and the polymer blocks. The optimum methods of structure directing are chemical pre-patterning (defining regions on the substrate of different chemistry and graphoepitaxy (topographical alignment but both centre on generating alignment through favourable chemical interactions. As in all self-assembling systems, the problems of defect formation must be considered and the origin of defects in these systems is explored. It is argued that in these nanostructures equilibrium defects are relatively few and largely originate from kinetic effects arising during film growth. Many defects also arise from the confinement of the systems when they are ‘directed’ by topography. The potential applications of these materials in electronics are discussed.

  5. Chemical Interactions and Their Role in the Microphase Separation of Block Copolymer Thin Films

    Science.gov (United States)

    Farrell, Richard A.; Fitzgerald, Thomas G.; Borah, Dipu; Holmes, Justin D.; Morris, Michael A.

    2009-01-01

    The thermodynamics of self-assembling systems are discussed in terms of the chemical interactions and the intermolecular forces between species. It is clear that there are both theoretical and practical limitations on the dimensions and the structural regularity of these systems. These considerations are made with reference to the microphase separation that occurs in block copolymer (BCP) systems. BCP systems self-assemble via a thermodynamic driven process where chemical dis-affinity between the blocks driving them part is balanced by a restorative force deriving from the chemical bond between the blocks. These systems are attracting much interest because of their possible role in nanoelectronic fabrication. This form of self-assembly can obtain highly regular nanopatterns in certain circumstances where the orientation and alignment of chemically distinct blocks can be guided through molecular interactions between the polymer and the surrounding interfaces. However, for this to be possible, great care must be taken to properly engineer the interactions between the surfaces and the polymer blocks. The optimum methods of structure directing are chemical pre-patterning (defining regions on the substrate of different chemistry) and graphoepitaxy (topographical alignment) but both centre on generating alignment through favourable chemical interactions. As in all self-assembling systems, the problems of defect formation must be considered and the origin of defects in these systems is explored. It is argued that in these nanostructures equilibrium defects are relatively few and largely originate from kinetic effects arising during film growth. Many defects also arise from the confinement of the systems when they are ‘directed’ by topography. The potential applications of these materials in electronics are discussed. PMID:19865513

  6. Patterning at the 10 nanometer length scale using a strongly segregating block copolymer thin film and vapor phase infiltration of inorganic precursors

    Science.gov (United States)

    Choi, Jonathan W.; Li, Zhaodong; Black, Charles T.; Sweat, Daniel P.; Wang, Xudong; Gopalan, Padma

    2016-06-01

    In this work, we demonstrate the use of self-assembled thin films of the cylinder-forming block copolymer poly(4-tert-butylstyrene-block-2-vinylpyridine) to pattern high density features at the 10 nm length scale. This material's large interaction parameter facilitates pattern formation in single-digit nanometer dimensions. This block copolymer's accessible order-disorder transition temperature allows thermal annealing to drive the assembly of ordered 2-vinylpyridine cylinders that can be selectively complexed with the organometallic precursor trimethylaluminum. This unique chemistry converts organic 2-vinylpyridine cylinders into alumina nanowires with diameters ranging from 8 to 11 nm, depending on the copolymer molecular weight. Graphoepitaxy of this block copolymer aligns and registers sub-12 nm diameter nanowires to larger-scale rectangular, curved, and circular features patterned by optical lithography. The alumina nanowires function as a robust hard mask to withstand the conditions required for patterning the underlying silicon by plasma etching. We conclude with a discussion of some of the challenges that arise with using block copolymers for patterning at sub-10 nm feature sizes.In this work, we demonstrate the use of self-assembled thin films of the cylinder-forming block copolymer poly(4-tert-butylstyrene-block-2-vinylpyridine) to pattern high density features at the 10 nm length scale. This material's large interaction parameter facilitates pattern formation in single-digit nanometer dimensions. This block copolymer's accessible order-disorder transition temperature allows thermal annealing to drive the assembly of ordered 2-vinylpyridine cylinders that can be selectively complexed with the organometallic precursor trimethylaluminum. This unique chemistry converts organic 2-vinylpyridine cylinders into alumina nanowires with diameters ranging from 8 to 11 nm, depending on the copolymer molecular weight. Graphoepitaxy of this block copolymer aligns and

  7. Processing Cyclic Peptide-polymer Conjugates in Block Copolymer Thin Films for Sub-nm Porous Membranes

    Science.gov (United States)

    Zhang, Chen; Xu, Ting

    2014-03-01

    Porous thin films containing subnanometer channels oriented normal to the surface exhibit unique transport and separation properties and can serve as selective membranes for separation. Inspired by natural protein channels, we have developed an approach using cyclic peptide nanotubes (CPNs) embedded in polymeric matrix to mimic the transport of natural channels. The co-assembly of polymer-covered CPNs in a block copolymer (BCP) thin film requires the synchronization of two self-assembly processes, namely the microphase separation of BCP and the nanotube growth of CP-polymer conjugates. We systematically investigated the co-assembly of isolated CP-poly(ethylene glycol) (CP-PEG) conjugates and polystyrene-b-poly (methyl methacrylate) (PS-b-PMMA) in thin films as a function of CP-PEG loading (fCP-PEG) and solvent-polymer interactions. We find that there is a strong dependence of the co-assembly process on fCP-PEG due to thermodynamic limit of incorporating one CPN in one PMMA microdomain, as well as the kinetic pathway in which favorable PEG-solvent interaction helps to disperse CPNs and thus lowers the activation energy barrier of the system. This study presents critical insights in guided assemblies of functional building blocks within nanoscopic frameworks. DOE-EFRC-Gas Separation, Army Research Office.

  8. Neutral wetting brush layers for block copolymer thin films using homopolymer blends

    Science.gov (United States)

    Antonioli, Diego; Sparnacci, Katia; Laus, Michele; Lupi, Federico Ferrarese; Giammaria, Tommaso Jacopo; Seguini, Gabriele; Ceresoli, Monica; Perego, Michele; Gianotti, Valentina

    2016-05-01

    Binary homopolymer blends of two hydroxyl-terminated polystyrene (PS-OH) and polymethylmethacrylate (PMMA-OH) homopolymers (Mn ~ 16000 g mol-1) were grafted on SiO2 substrates by high-temperature (T > 150 °C), short-time (t blend composition and the processing parameters, an efficient surface neutralization path was identified, enabling the formation, in the block copolymer film, of homogeneous textures of lamellae or cylinders perpendicularly oriented with respect to the substrate. A critical interplay between the phase segregation of the homopolymer blends and their grafting process on the SiO2 was observed. In fact, the polar SiO2 is preferential for the PMMA-rich phase that forms a homogeneous layer on the substrate, while the PS-rich phase is located at the polymer-air interface. During the thermal treatment, phase segregation and grafting proceed simultaneously. Complete wetting of the PS rich phase on the PMMA rich phase leads to the formation of a PS/PMMA bilayer. In this case, the progressive diffusion of PS chains toward the polymer-SiO2 interface during the thermal treatment allows tuning of the brush layer composition

  9. Line edge roughness measurement technique for fingerprint pattern in block copolymer thin film

    Science.gov (United States)

    Isawa, Miki; Sakai, Kei; Rincon Delgadillo, Paulina A.; Gronheid, Roel; Yoshida, Hiroshi

    2013-04-01

    Fingerprint edge roughness (FER) is proposed to characterize high frequency roughness of fingerprint pattern edges assembled by lamella forming block copolymer (BCP). The FER is a roughness index which does not include the roughness component of the fingerprint curvature. A technique to evaluate FER by using CD-SEM is also proposed. Centerline of the fingerprint patterns were extracted by utilizing binarization and slimming algorithm, and line width, line width roughness and line edge roughness along the centerline were measured. The FER thus measured showed a good agreement with those determined by utilizing conventional line edge roughness analyzing algorithm. The FERs of fingerprint patterns assembled with various BCP formulations were analyzed. As a result, the proposed technique successfully detected the line edge roughness difference between each BCP formulations with different compositions. The results indicate that the FER might be a useful index to evaluate the patterning performance of BCP as a material for DSA process. The proposed technique will provide a method for fast and easy development of BCP materials and processes

  10. Controlling the Morphology of Side Chain Liquid Crystalline Block Copolymer Thin Films through Variations in Liquid Crystalline Content

    OpenAIRE

    Verploegen, Eric; Zhang, Tejia; Jung, Yeon Sik; Ross, Caroline; Hammond, Paula T.

    2008-01-01

    In this paper we describe methods for manipulating the morphology of side-chain liquid crystalline block copolymers through variations in the liquid crystalline content. By systematically controlling the covalent attachment of side chain liquid crystals to a block copolymer (BCP) backbone, the morphology of both the liquid crystalline (LC) mesophase and the phase segregated BCP microstructures can be precisely manipulated. Increases in LC functionalization lead to stronger preferences for the...

  11. Fabrication of Highly Ordered Polymeric Nanodot and Nanowire Arrays Templated by Supramolecular Assembly Block Copolymer Nanoporous Thin Films

    Directory of Open Access Journals (Sweden)

    Liu Xikui

    2009-01-01

    Full Text Available Abstract Realizing the vast technological potential of patternable block copolymers requires both the precise controlling of the orientation and long-range ordering, which is still a challenging topic so far. Recently, we have demonstrated that ordered nanoporous thin film can be fabricated from a simple supramolecular assembly approach. Here we will extend this approach and provide a general route to fabricate large areas of highly ordered polymeric nanodot and nanowire arrays. We revealed that under a mixture solvent annealing atmosphere, a near-defect-free nanoporous thin film over large areas can be achieved. Under the direction of interpolymer hydrogen bonding and capillary action of nanopores, this ordered porous nanotemplate can be properly filled with phenolic resin precursor, followed by curation and pyrolysis at middle temperature to remove the nanotemplate, a perfect ordered polymer nanodot arrays replication was obtained. The orientation of the supramolecular assembly thin films can be readily re-aligned parallel to the substrate upon exposure to chloroform vapor, so this facile nanotemplate replica method can be further extend to generate large areas of polymeric nanowire arrays. Thus, we achieved a successful sub-30 nm patterns nanotemplates transfer methodology for fabricating polymeric nanopattern arrays with highly ordered structure and tunable morphologies.

  12. Micrometer-Scale Ordering of Silicon-Containing Block Copolymer Thin Films via High-Temperature Thermal Treatments.

    Science.gov (United States)

    Giammaria, Tommaso Jacopo; Ferrarese Lupi, Federico; Seguini, Gabriele; Perego, Michele; Vita, Francesco; Francescangeli, Oriano; Wenning, Brandon; Ober, Christopher K; Sparnacci, Katia; Antonioli, Diego; Gianotti, Valentina; Laus, Michele

    2016-04-20

    Block copolymer (BCP) self-assembly is expected to complement conventional optical lithography for the fabrication of next-generation microelectronic devices. In this regard, silicon-containing BCPs with a high Flory-Huggins interaction parameter (χ) are extremely appealing because they form high-resolution nanostructures with characteristic dimensions below 10 nm. However, due to their slow self-assembly kinetics and low thermal stability, these silicon-containing high-χ BCPs are usually processed by solvent vapor annealing or in solvent-rich ambient at a low annealing temperature, significantly increasing the complexity of the facilities and of the procedures. In this work, the self-assembly of cylinder-forming polystyrene-block-poly(dimethylsiloxane-random-vinylmethylsiloxane) (PS-b-P(DMS-r-VMS)) BCP on flat substrates is promoted by means of a simple thermal treatment at high temperatures. Homogeneous PS-b-P(DMS-r-VMS) thin films covering the entire sample surface are obtained without any evidence of dewetting phenomena. The BCP arranges in a single layer of cylindrical P(DMS-r-VMS) nanostructures parallel-oriented with respect to the substrate. By properly adjusting the surface functionalization, the heating rate, the annealing temperature, and the processing time, one can obtain correlation length values larger than 1 μm in a time scale fully compatible with the stringent requirements of the microelectronic industry. PMID:27020526

  13. Solvothermal Vapor Annealing of Lamellar Poly(styrene)-block-poly(d,l-lactide) Block Copolymer Thin Films for Directed Self-Assembly Application.

    Science.gov (United States)

    Cummins, Cian; Mokarian-Tabari, Parvaneh; Andreazza, Pascal; Sinturel, Christophe; Morris, Michael A

    2016-03-30

    Solvothermal vapor annealing (STVA) was employed to induce microphase separation in a lamellar forming block copolymer (BCP) thin film containing a readily degradable block. Directed self-assembly of poly(styrene)-block-poly(d,l-lactide) (PS-b-PLA) BCP films using topographically patterned silicon nitride was demonstrated with alignment over macroscopic areas. Interestingly, we observed lamellar patterns aligned parallel as well as perpendicular (perpendicular microdomains to substrate in both cases) to the topography of the graphoepitaxial guiding patterns. PS-b-PLA BCP microphase separated with a high degree of order in an atmosphere of tetrahydrofuran (THF) at an elevated vapor pressure (at approximately 40-60 °C). Grazing incidence small-angle X-ray scattering (GISAXS) measurements of PS-b-PLA films reveal the through-film uniformity of perpendicular microdomains after STVA. Perpendicular lamellar orientation was observed on both hydrophilic and relatively hydrophobic surfaces with a domain spacing (L0) of ∼32.5 nm. The rapid removal of the PLA microdomains is demonstrated using a mild basic solution for the development of a well-defined PS mask template. GISAXS data reveal the through-film uniformity is retained following wet etching. The experimental results in this article demonstrate highly oriented PS-b-PLA microdomains after a short annealing period and facile PLA removal to form porous on-chip etch masks for nanolithography application. PMID:26950246

  14. Rheological and Mechanical behaviour of Block copolymers, Multigraft copolymers and Block copolymer Nanocomposites

    OpenAIRE

    Thunga, Mahendra

    2009-01-01

    Block copolymers are commercially significant and fundamentally interesting class of polymeric materials. The ability to undergo interfacial thermodynamics-controlled microphase separation from a completely disordered state in the melt to a specifically defined ordered structure through self-organization makes the block copolymers based materials unique. Block copolymer are strongly replacing many of the commercially available polymers due to their unique microstructure and properties. The mo...

  15. Materials Design for Block Copolymer Lithography

    Science.gov (United States)

    Sweat, Daniel Patrick

    Block copolymers (BCPs) have attracted a great deal of scientific and technological interest due to their ability to spontaneously self-assemble into dense periodic nanostructures with a typical length scale of 5 to 50 nm. The use of self-assembled BCP thin-films as templates to form nanopatterns over large-area is referred to as BCP lithography. Directed self-assembly of BCPs is now viewed as a viable candidate for sub-20 nm lithography by the semiconductor industry. However, there are multiple aspects of assembly and materials design that need to be addressed in order for BCP lithography to be successful. These include substrate modification with polymer brushes or mats, tailoring of the block copolymer chemistry, understanding thin-film assembly and developing epitaxial like methods to control long range alignment. The rational design, synthesis and self-assembly of block copolymers with large interaction parameters (chi) is described in the first part of this dissertation. Two main blocks were chosen for introducing polarity into the BCP system, namely poly(4-hydroxystyrene) and poly(2-vinylpyridine). Each of these blocks are capable of ligating Lewis acids which can increase the etch contrast between the blocks allowing for facile pattern transfer to the underlying substrate. These BCPs were synthesized by living anionic polymerization and showed excellent control over molecular weight and dispersity, providing access to sub 5-nm domain sizes. Polymer brushes consist of a polymer chain with one end tethered to the surface and have wide applicability in tuning surface energy, forming responsive surfaces and increasing biocompatibility. In the second part of the dissertation, we present a universal method to grow dense polymer brushes on a wide range of substrates and combine this chemistry with BCP assembly to fabricate nanopatterned polymer brushes. This is the first demonstration of introducing additional functionality into a BCP directing layer and opens up

  16. Micellization and Dynamics of a Block Copolymer

    DEFF Research Database (Denmark)

    Hvidt, Søren

    2006-01-01

    Triblock copolymers of the type EPE, where E and P denote ethylene oxide and propylene oxide blocks, respectively, are industrially important copolymers often called Pluronics or Poloxamers. EPE copolymers form micelles with a core of P blocks and different micellar shapes depending on block length...... copolymer mixtures, and evidence in favor of a multi-equilibria unimer-micelle model will be presented. Results obtained by liquid chromatographic methods will be shown and it will be demonstrated that commercial EPE copolymers are inhomogeneous at several levels and many of their unusual properties reflect...

  17. Effect of annealing and UV-radiation time over micropore architecture of self-assembled block copolymer thin film

    Directory of Open Access Journals (Sweden)

    G. del C. Pizarro

    2015-06-01

    Full Text Available Block copolymers have been recognized as versatile materials to prepare nanoporous polymer films or membranes, but their potential has not been completely explored. This study focuses on the formation and characterization of nanoporous polymer films based on poly(styrene-block-(methylmethacrylate/methacrylic acid; (PS-b-MMA/MAA were obtained through atom transfer radical polymerization (ATRP, by using two different protocols: annealing and annealingirradiation; for improving the formation of microporous surface. The composition, crystallinity and structural order of the films were studied by Raman spectroscopy. The film polymer thickness was obtained through very high resolution ellipsometry (VHRE. Finally, atomic force microcopy (AFM and scanning electron microscopy (SEM techniques were used to detect changes in the porous-structure. These results show that the morphological properties of the block copolymer were affected via the modification of two variables, UV-radiation time and annealing. SEM and AFM micrographs showed that the morphology exhibit a porous ordered structure. Contact angle measurement suggests additional interactions between hydrophilic functional groups that influence the film wettability.

  18. Nanopatterned articles produced using surface-reconstructed block copolymer films

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Thomas P.; Park, Soojin; Wang, Jia-Yu; Kim, Bokyung

    2016-06-07

    Nanopatterned surfaces are prepared by a method that includes forming a block copolymer film on a substrate, annealing and surface reconstructing the block copolymer film to create an array of cylindrical voids, depositing a metal on the surface-reconstructed block copolymer film, and heating the metal-coated block copolymer film to redistribute at least some of the metal into the cylindrical voids. When very thin metal layers and low heating temperatures are used, metal nanodots can be formed. When thicker metal layers and higher heating temperatures are used, the resulting metal structure includes nanoring-shaped voids. The nanopatterned surfaces can be transferred to the underlying substrates via etching, or used to prepare nanodot- or nanoring-decorated substrate surfaces.

  19. The Synthesis, Self-Assembly and Self-Organisation of Polysilane Block Copolymers

    OpenAIRE

    Holder, Simon J.; Jones, Richard G.

    2008-01-01

    Block copolymers containing polysilane blocks are unique in that the polysilane components possess electro-active properties and are readily photodegradable. This review will discuss and assess the two major approaches to the synthesis of polysilane block copolymers via pre-formed polymer chain coupling and living polymerisation techniques. The self-organisation of polysilane block copolymers and the morphologies adopted in thin films are reviewed. Amphiphilic polysilane-containing block copo...

  20. PEO-related block copolymer surfactants

    DEFF Research Database (Denmark)

    Mortensen, K.

    2001-01-01

    Non-ionic block copolymer systems based on hydrophilic poly(ethylene oxide) and more hydrophobic co-polymer blocks are used intensively in a variety of industrial and personal applications. A brief description on the applications is presented. The physical properties of more simple model systems ...

  1. STUDY ON POLYSULFONE-POLYESTER BLOCK COPOLYMERS

    Institute of Scientific and Technical Information of China (English)

    DING Youjun; QI Daquan

    1988-01-01

    Synthesis and characterization of a series of Polysulfone (PSF)-Polyester (PEs) block copolymers were studied.The degree of randomness (B) of these block copolymers was calculated from the intensities of their proton signals in 1H NMR spectra and lies in the region of 0 < B < 1. It was shown that the degree of randomness (B) and the average sequence length (L) in block copolymers were relatively dependent on the reaction conditions, various feed ratios and structure of diols.The phenomenon was observed, when the PSF-PEs block copolymers dissolved in different solvents they had different viscosities and molecular conformations.The PSF-PEs block copolymers had better solvent resistance than homo-polysulfone.

  2. Combining mixed titania morphologies into a complex assembly thin film by iterative block-copolymer-based sol-gel templating

    Science.gov (United States)

    Niedermeier, M. A.; Magerl, D.; Zhong, Q.; Nathan, A.; Körstgens, V.; Perlich, J.; Roth, S. V.; Müller-Buschbaum, P.

    2012-04-01

    Sol-gel templating combined with iterative spin-coating steps are used to custom-tailor hierarchically structured titania thin films. Using poly(styrene-block-ethylene oxide) P(S-b-PEO) as the structure directing agent, a foam-like structure is combined with nanogranules. Both structural elements are merged into a complex assembly in thin film geometry. The resulting morphology is pictured by SEM and probed with GISAXS. The installed mesoporous titania sandwich structure exhibits holes with a size of 45 nm which makes it promising for applications in photovoltaics or photocatalysis. An optical characterization completes the structural investigation.

  3. Self-assembly of block copolymers

    Directory of Open Access Journals (Sweden)

    Hidenori Otsuka

    2001-05-01

    Full Text Available Block copolymers in a selective solvent have a tendency to self-assemble at surfaces and into micelles1–4. At an aqueous interface, the amphiphilic property of block copolymers composed of hydrophilic and hydrophobic segments can cause the distal end of the hydrophilic chain to extend into the bulk aqueous solution, anchoring the hydrophilic block to the substrate surface through hydrophobic segments1, 2. In an aqueous solution, micelles with core-shell structure are formed by the segregation of insoluble blocks into the core, which is surrounded by a hydrophilic shell composed of hydrophilic blocks3, 4. This interfacial activity of amphiphilic block copolymers provides their utility in the biomedical field as colloidal dispersants, surface modifiers and drug carriers, prompting many studies of block copolymer adsorption on solid surfaces5, 6, 7, 8, force measurements between tethered layers9, 10, 11 and the characterization of micelle properties12, 13, 14.

  4. Comparing Fluid and Elastic Block Copolymer Shells

    Science.gov (United States)

    Rozairo, Damith; Croll, Andrew B.

    2014-03-01

    Emulsions can be stabilized with the addition of an amphiphilic diblock copolymer, resulting in droplets surrounded and protected by a polymer monolayer. Such droplets show considerable promise as advanced cargo carriers in pharmaceuticals or cosmetics due to their strength and responsiveness. Diblock copolymer interfaces remain mostly fluid and may not be able to attain the mechanical performance desired by industry. To strengthen block copolymer emulsion droplets we have developed a novel method for creating thin elastic shells using polystyrene-b-poly(acrylic acid)-b-polystyrene (PS-PAA-PS). Characterization of the fluid filled elastic shells is difficult with traditional means which lead us to develop a new and general method of mechanical measurement. Specifically, we use laser scanning confocal microscopy to achieve a high resolution measure of the deformation of soft spheres under the influence of gravity. To prove the resilience of the technique we examine both a polystyrene-b-poly(ethylene oxide) (PS-PEO) stabilized emulsion and the PS-PAA-PS emulsion. The mechanical measurement allows the physics of the polymer at the interface to be examined, which will ultimately lead to the rational development of these technologies.

  5. Functional Nanoporous Polymers from Block Copolymer Precursors

    OpenAIRE

    Guo, Fengxiao

    2010-01-01

    Abstract Self-assembly of block copolymers provides well-defined morphologies with characteristic length scales in the nanometer range. Nanoporous polymers prepared by selective removal of one block from self-assembled block copolymers offer great technological promise due to their many potential applications as, e.g., membranes for separation and purification, templates for nanostructured materials, sensors, substrates for catalysis, low dielectric constant materials, photonic materials, and...

  6. Photo-Induced Micellization of Block Copolymers

    OpenAIRE

    Satoshi Kuwayama; Eri Yoshida

    2010-01-01

    We found novel photo-induced micellizations through photolysis, photoelectron transfer, and photo-Claisen rearrangement. The photolysis-induced micellization was attained using poly(4-tert-butoxystyrene)-block-polystyrene diblock copolymer (PBSt-b-PSt). BSt-b-PSt showed no self-assembly in dichloromethane and existed as isolated copolymers. Dynamic light scattering demonstrated that the copolymer produced spherical micelles in this solvent due to irradiation with a high-pressure mercury lamp ...

  7. Block Copolymer Membranes for Biofuel Purification

    Science.gov (United States)

    Evren Ozcam, Ali; Balsara, Nitash

    2012-02-01

    Purification of biofuels such as ethanol is a matter of considerable concern as they are produced in complex multicomponent fermentation broths. Our objective is to design pervaporation membranes for concentrating ethanol from dilute aqueous mixtures. Polystyrene-b-polydimethylsiloxane-b-polystyrene block copolymers were synthesized by anionic polymerization. The polydimethylsiloxane domains provide ethanol-transporting pathways, while the polystyrene domains provide structural integrity for the membrane. The morphology of the membranes is governed by the composition of the block copolymer while the size of the domains is governed by the molecular weight of the block copolymer. Pervaporation data as a function of these two parameters will be presented.

  8. PEO-related block copolymer surfactants

    DEFF Research Database (Denmark)

    Mortensen, K.

    Non-ionic block copolymer systems based on hydrophilic poly(ethylene oxide) and more hydrophobic co-polymer blocks are used intensively in a variety of industrial and personal applications. A brief description on the applications is presented. The physical properties of more simple model systems of...... such PEG-based block copolymers in aqueous suspensions are reviewed. Based on scattering experiments using either X-ray or neutrons, the phase behavior is characterized, showing that the thermo-reversible gelation is a result of micellar ordering into mesoscopic crystalline phases of cubic, hexagonal...

  9. Functional Nanoporous Polymers from Block Copolymer Precursors

    DEFF Research Database (Denmark)

    Guo, Fengxiao

    functionalities remains a great challenge due to the limitation of available polymer synthesis and the nanoscale confinement of the porous cavities. The main topic of this thesis is to develop methods for fabrication of functional nanoporous polymers from block copolymer precursors. A method has been developed......Abstract Self-assembly of block copolymers provides well-defined morphologies with characteristic length scales in the nanometer range. Nanoporous polymers prepared by selective removal of one block from self-assembled block copolymers offer great technological promise due to their many potential......, where living anionic polymerization and atom transfer radical polymerization (ATRP) are combined to synthesize a polydimethylsiloxane-b-poly(tert-butyl acrylate)-b-polystyrene (PDMS-b-PtBA-b-PS) triblock copolymer precursor. By using either anhydrous hydrogen fluoride or trifluoroacetic acid, PtBA block...

  10. Block copolymer membranes for aqueous solution applications

    KAUST Repository

    Nunes, Suzana Pereira

    2016-03-22

    Block copolymers are known for their intricate morphology. We review the state of the art of block copolymer membranes and discuss perspectives in this field. The main focus is on pore morphology tuning with a short introduction on non-porous membranes. The two main strategies for pore formation in block copolymer membranes are (i) film casting and selective block sacrifice and (ii) self-assembly and non-solvent induced phase separation (SNIPS). Different fundamental aspects involved in the manufacture of block copolymer membranes are considered, including factors affecting the equilibrium morphology in solid films, self-assembly of copolymer in solutions and macrophase separation by solvent-non-solvent exchange. Different mechanisms are proposed for different depths of the SNIPS membrane. Block copolymer membranes can be prepared with much narrower pore size distribution than homopolymer membranes. Open questions and indications of what we consider the next development steps are finally discussed. They include the synthesis and application of new copolymers and specific functionalization, adding characteristics to respond to stimuli and chemical environment, polymerization-induced phase separation, and the manufacture of organic-inorganic hybrids.

  11. Thermal annealing as an easy tool for the controlled arrangement of gold nanoparticles in block-copolymer thin films

    Science.gov (United States)

    Ledo-Suárez, Ana; Hoppe, Cristina Elena; Lazzari, Massimo; Lopez Quintela, M. Arturo; Zucchi, Ileana Alicia

    2013-06-01

    Thermal annealing was used for the bottom-up fabrication of morphologically controlled gold-block-copolymer (Au-BC) nanocomposites. Three different blends formed by polystyrene (PS) homopolymer and PS-coated gold nanoparticles (PSSH@Au) were used as modifiers of asymmetric polystyrene-b-polymethylmethacrylate (PS-b-PMMA): PS26/PS26SH@Au, PS75/PS75SH@Au and PS167/PS167SH@Au (where the subscripts refer to the number of styrene monomeric units). The results indicated that all three blends used as modifiers (PSn/PSnSH@Au) were successfully located in the PS phase during thermally induced BC self-assembly for a composition range from 5 to 43 wt% without macro-phase separation. The PSnSH@Au moiety experienced molecular desorption, nanocrystal core coalescence and partial molecular re-encapsulation processes during thermal annealing, leading to sphere-like gold NPs with a larger average size (without exceeding an interdomain distance). Ligand chain length regulated the degree of coalescence and re-encapsulation, defining ultimate core size. Furthermore, proper combination of chain length and composition enabled tuning of NP partitioning and arrangement on different length scales through thermally activated cooperative assembly processes. These results have not only significant impact for establishing thermal processing as a useful tool for the precise control of NP size and distribution, but also much broader implications for many nanoparticle-based technologies.

  12. Thermal annealing as an easy tool for the controlled arrangement of gold nanoparticles in block-copolymer thin films

    International Nuclear Information System (INIS)

    Thermal annealing was used for the bottom-up fabrication of morphologically controlled gold–block-copolymer (Au–BC) nanocomposites. Three different blends formed by polystyrene (PS) homopolymer and PS-coated gold nanoparticles (PSSH-Au) were used as modifiers of asymmetric polystyrene-b-polymethylmethacrylate (PS-b-PMMA): PS26/PS26SH-Au, PS75/PS75SH-Au and PS167/PS167SH-Au (where the subscripts refer to the number of styrene monomeric units). The results indicated that all three blends used as modifiers (PSn/PSnSH-Au) were successfully located in the PS phase during thermally induced BC self-assembly for a composition range from 5 to 43 wt% without macro-phase separation. The PSnSH-Au moiety experienced molecular desorption, nanocrystal core coalescence and partial molecular re-encapsulation processes during thermal annealing, leading to sphere-like gold NPs with a larger average size (without exceeding an interdomain distance). Ligand chain length regulated the degree of coalescence and re-encapsulation, defining ultimate core size. Furthermore, proper combination of chain length and composition enabled tuning of NP partitioning and arrangement on different length scales through thermally activated cooperative assembly processes. These results have not only significant impact for establishing thermal processing as a useful tool for the precise control of NP size and distribution, but also much broader implications for many nanoparticle-based technologies. (paper)

  13. Nanostructured Polysulfone-Based Block Copolymer Membranes

    KAUST Repository

    Xie, Yihui

    2016-05-01

    The aim of this work is to fabricate nanostructured membranes from polysulfone-based block copolymers through self-assembly and non-solvent induced phase separation. Block copolymers containing polysulfone are novel materials for this purpose providing better mechanical and thermal stability to membranes than polystyrene-based copolymers, which have been exclusively used now. Firstly, we synthesized a triblock copolymer, poly(tert-butyl acrylate)-b-polsulfone-b-poly(tert-butyl acrylate) through polycondensation and reversible addition-fragmentation chain-transfer polymerization. The obtained membrane has a highly porous interconnected skin layer composed of elongated micelles with a flower-like arrangement, on top of the graded finger-like macrovoids. Membrane surface hydrolysis was carried out in a combination with metal complexation to obtain metal-chelated membranes. The copper-containing membrane showed improved antibacterial capability. Secondly, a poly(acrylic acid)-b-polysulfone-b-poly(acrylic acid) triblock copolymer obtained by hydrolyzing poly(tert-butyl acrylate)-b-polsulfone-b-poly(tert-butyl acrylate) formed a thin film with cylindrical poly(acrylic acid) microdomains in polysulfone matrix through thermal annealing. A phase inversion membrane was prepared from the same polymer via self-assembly and chelation-assisted non-solvent induced phase separation. The spherical micelles pre-formed in a selective solvent mixture packed into an ordered lattice in aid of metal-poly(acrylic acid) complexation. The space between micelles was filled with poly(acrylic acid)-metal complexes acting as potential water channels. The silver0 nanoparticle-decorated membrane was obtained by surface reduction, having three distinct layers with different particle sizes. Other amphiphilic copolymers containing polysulfone and water-soluble segments such as poly(ethylene glycol) and poly(N-isopropylacrylamide) were also synthesized through coupling reaction and copper0-mediated

  14. Rapid self-assembly of block copolymers to photonic crystals

    Energy Technology Data Exchange (ETDEWEB)

    Xia, Yan; Sveinbjornsson, Benjamin R; Grubbs, Robert H; Weitekamp, Raymond; Miyake, Garret M; Atwater, Harry A; Piunova, Victoria; Daeffler, Christopher Scot; Hong, Sung Woo; Gu, Weiyin; Russell, Thomas P.

    2016-07-05

    The invention provides a class of copolymers having useful properties, including brush block copolymers, wedge-type block copolymers and hybrid wedge and polymer block copolymers. In an embodiment, for example, block copolymers of the invention incorporate chemically different blocks comprising polymer size chain groups and/or wedge groups that significantly inhibit chain entanglement, thereby enhancing molecular self-assembly processes for generating a range of supramolecular structures, such as periodic nanostructures and microstructures. The present invention also provides useful methods of making and using copolymers, including block copolymers.

  15. Host-Guest Self-assembly in Block Copolymer Blends

    OpenAIRE

    Woon Ik Park; YongJoo Kim; Jae Won Jeong; Kyungho Kim; Jung-Keun Yoo; Yoon Hyung Hur; Jong Min Kim; Thomas, Edwin L.; Alfredo Alexander-Katz; Yeon Sik Jung

    2013-01-01

    Ultrafine, uniform nanostructures with excellent functionalities can be formed by self-assembly of block copolymer (BCP) thin films. However, extension of their geometric variability is not straightforward due to their limited thin film morphologies. Here, we report that unusual and spontaneous positioning between host and guest BCP microdomains, even in the absence of H-bond linkages, can create hybridized morphologies that cannot be formed from a neat BCP. Our self-consistent field theory (...

  16. Functionalization of Block Copolymer Vesicle Surfaces

    Directory of Open Access Journals (Sweden)

    Wolfgang Meier

    2011-01-01

    Full Text Available In dilute aqueous solutions certain amphiphilic block copolymers self-assemble into vesicles that enclose a small pool of water with a membrane. Such polymersomes have promising applications ranging from targeted drug-delivery devices, to biosensors, and nanoreactors. Interactions between block copolymer membranes and their surroundings are important factors that determine their potential biomedical applications. Such interactions are influenced predominantly by the membrane surface. We review methods to functionalize block copolymer vesicle surfaces by chemical means with ligands such as antibodies, adhesion moieties, enzymes, carbohydrates and fluorophores. Furthermore, surface-functionalization can be achieved by self-assembly of polymers that carry ligands at their chain ends or in their hydrophilic blocks. While this review focuses on the strategies to functionalize vesicle surfaces, the applications realized by, and envisioned for, such functional polymersomes are also highlighted.

  17. Micellization and Characterization of Block Copolymer Detergents

    DEFF Research Database (Denmark)

    Hvidt, Søren

    Triblock copolymers of the type EPE, where E and P denote ethylene oxide and propylene oxide blocks, respectively, are used widely in industry as emulsifiers, anti-foaming agents, and in delayed drug release. EPE copolymers form micelles with a core of P blocks and different micellar shapes...... depending on block length ratios and temperature. The micellization process with increasing temperature or concentration has been followed by a number of techniques including differential scanning calorimetry and surface tension measurements. The detailed micellar mechanism is not well understood and...... different models have been proposed. Results obtained by a range of liquid chromatographic methods will be shown and it will be demonstrated that commercial EPE copolymers are inhomogeneous at several levels and many of their unusual properties reflect the presence of impurities....

  18. Substrate tolerant direct block copolymer nanolithography

    DEFF Research Database (Denmark)

    Li, Tao; Wang, Zhongli; Schulte, Lars;

    2016-01-01

    simplifies the main stream BC lithography process, showing a broad substrate tolerance and allowing for efficient pattern transfer over wafer scale. PDMS-rich poly(styrene-b-dimethylsiloxane) (PS-b-PDMS) copolymers are directly applied on substrates including polymers, silicon and graphene. A single oxygen......Block copolymer (BC) self-assembly constitutes a powerful platform for nanolithography. However, there is a need for a general approach to BC lithography that critically considers all the steps from substrate preparation to the final pattern transfer. We present a procedure that significantly...... plasma treatment enables formation of the oxidized PDMS hard mask, PS block removal and polymer or graphene substrate patterning....

  19. Controlled Architecture of Dual-Functional Block Copolymer Brushes on Thin-Film Composite Membranes for Integrated "Defending" and "Attacking" Strategies against Biofouling.

    Science.gov (United States)

    Ye, Gang; Lee, Jongho; Perreault, François; Elimelech, Menachem

    2015-10-21

    We report a new macromolecular architecture of dual functional block copolymer brushes on commercial thin-film composite (TFC) membranes for integrated "defending" and "attacking" strategies against biofouling. Mussel-inspired catechol chemistry is used for a convenient immobilization of initiator molecules to the membrane surface with the aid of polydopamine (PDA). Zwitterionic polymer brushes with strong hydration capacity and quaternary ammonium salt (QAS) polymer brushes with bactericidal ability are sequentially grafted on TFC membranes via activators regenerated by electron transfer-atom transfer radical polymerization (ARGET-ATRP), an environmentally benign and controlled polymerization method. Measurement of membrane intrinsic transport properties in reverse osmosis experiments shows that the modified TFC membrane maintains the same water permeability and salt selectivity as the pristine TFC membrane. Chemical force microscopy and protein/bacterial adhesion studies are carried out for a comprehensive evaluation of the biofouling resistance and antimicrobial ability, demonstrating low biofouling propensity and excellent bacterial inactivation for the modified TFC membrane. We conclude that this polymer architecture, with complementary "defending" and "attacking" capabilities, can effectively prevent the attachment of biofoulants and formation of biofilms and thereby significantly mitigate biofouling on TFC membranes. PMID:26378606

  20. Thermodynamic Interactions in Organometallic Block Copolymers

    International Nuclear Information System (INIS)

    The thermodynamic interactions in anionically synthesized poly(styrene-block-ferrocenyldimethylsilane) (SF) copolymers were examined using birefringence, small angle X-ray and neutron scattering (SAXS and SANS). We show that birefringence detection of the order-disorder transition is possible in colored samples provided the wavelength of the incident beam is in the tail of the absorption spectrum. The location of the order-disorder transition was confirmed by SAXS. The temperature-dependence of the Flory-Huggins parameter, χ, of SF copolymers, determined by SAXS, is similar in magnitude to that between polystyrene and polyisoprene chains. We find that χ is independent of block copolymer composition (within experimental error). We also demonstrate that the neutron scattering length densities of styrene and ferrocenyldimethylsilane moieties are identical due to a surprising cancellation of factors related to density and atomic composition

  1. Metallo-supramolecular block copolymers : from synthesis to smart nanomaterials

    OpenAIRE

    Guillet, Pierre

    2008-01-01

    Supramolecular copolymers have become of increasing interest in recent years for the search of new materials with tunable properties. In particular, metallo-supramolecular block copolymers have seen important progresses since the last five years. In this thesis, a library of metallo-supramolecular amphiphilic block copolymers containing a hydrophilic block, linked to a hydrophobic block, through a metal-ligand complex has been investigated. The micelles formed in water from these copolymers...

  2. Influence of substrate interaction and confinement on electric-field-induced transition in symmetric block-copolymer thin films

    Science.gov (United States)

    Mukherjee, Arnab; Mukherjee, Rajdip; Ankit, Kumar; Bhattacharya, Avisor; Nestler, Britta

    2016-03-01

    In the present work, we study morphologies arising due to competing substrate interaction, electric field, and confinement effects on a symmetric diblock copolymer. We employ a coarse-grained nonlocal Cahn-Hilliard phenomenological model taking into account the appropriate contributions of substrate interaction and electrostatic field. The proposed model couples the Ohta-Kawasaki functional with Maxwell equation of electrostatics, thus alleviating the need for any approximate solution used in previous studies. We calculate the phase diagram in electric-field-substrate strength space for different film thicknesses. In addition to identifying the presence of parallel, perpendicular, and mixed lamellae phases similar to analytical calculations, we also find a region in the phase diagram where hybrid morphologies (combination of two phases) coexist. These hybrid morphologies arise either solely due to substrate affinity and confinement or are induced due to the applied electric field. The dependence of the critical fields for transition between the various phases on substrate strength, film thickness, and dielectric contrast is discussed. Some preliminary 3D results are also presented to corroborate the presence of hybrid morphologies.

  3. Regulating block copolymer phases via selective homopolymers

    International Nuclear Information System (INIS)

    The phase behavior of strongly segregated AB diblock copolymer and selective C homopolymer blends is examined theoretically using a combination of strong stretching theory (SST) and self-consistent field theory (SCFT). The C-homopolymer is immiscible with the B-blocks but strongly attractive with the A-blocks. The effect of homopolymer content on the order-order phase transitions is analyzed. It is observed that, for AB diblock copolymers with majority A-blocks, the addition of the C-homopolymers results in lamellar to cylindrical to spherical phase transitions because of the A/C complexation. For diblock copolymers with minor A-blocks, adding C-homopolymers leads to transitions from spherical or cylindrical morphology with A-rich core to lamellae to inverted cylindrical and spherical morphologies with B-rich core. The results from analytical SST and numerical SCFT are in good agreement within most regions of the phase diagram. But the deviation becomes more obvious when the composition of A-blocks is too small and the content of added C-homopolymers is large enough, where the SCFT predicts a narrow co-existence region between different ordered phases. Furthermore, it is found that the phase behavior of the system is insensitive to the molecular weight of C-homopolymer

  4. Diamond-Forming Block Copolymers and Diamond-like Morphologies: a New Route towards efficient Block Copolymer Membranes?

    Science.gov (United States)

    Erukhimovich, Igor; Kriksin, Yury

    2014-03-01

    Formation of ordered (microphase separated) block copolymer nanostructures is a promising route towards creating isoporous membranes suitable for technological applications. We propose a new route to achieve this target: to choose such block copolymer architectures, which would provide a practically isotropic permeability both in the bulk and in thin films. Basing both on the weak segregation theory extension into the thin films and the self-consistent field theory numerical procedure we present the results concerning the effects of the wall confinement both with neutral, selective and patterned walls on the structure and stability of the block copolymer ordered films. The diamond-like morphology is found to be the most promising one as to optimizing the permeability of thin films. A new effect of the diamond morphology stability enhancement in the presence of a properly designed lamellar-like wall pattern is discovered and the corresponding phase diagram demonstrating the effect of the pattern scale and film width on the diamond morphology stability is presented. The financial support was provided by Ministry of Science and Education of Russian Federation (State Contract No. 02.740.11.0858) and European Commission (FP7 project NMP3-SL-2009- 228652 (SELFMEM)).

  5. Dynamics of Block Copolymer Nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Mochrie, Simon G. J.

    2014-09-09

    A detailed study of the dynamics of cadmium sulfide nanoparticles suspended in polystyrene homopolymer matrices was carried out using X-ray photon correlation spectroscopy for temperatures between 120 and 180 °C. For low molecular weight polystyrene homopolymers, the observed dynamics show a crossover from diffusive to hyper-diffusive behavior with decreasing temperatures. For higher molecular weight polystyrene, the nanoparticle dynamics appear hyper-diffusive at all temperatures studied. The relaxation time and characteristic velocity determined from the measured hyper-diffusive dynamics reveal that the activation energy and underlying forces determined are on the order of 2.14 × 10-19 J and 87 pN, respectively. We also carried out a detailed X-ray scattering study of the static and dynamic behavior of a styrene– isoprene diblock copolymer melt with a styrene volume fraction of 0.3468. At 115 and 120 °C, we observe splitting of the principal Bragg peak, which we attribute to phase coexistence of hexagonal cylindrical and cubic double- gyroid structure. In the disordered phase, above 130 °C, we have characterized the dynamics of composition fluctuations via X-ray photon correlation spectroscopy. Near the peak of the static structure factor, these fluctuations show stretched-exponential relaxations, characterized by a stretching exponent of about 0.36 for a range of temperatures immediately above the MST. The corresponding characteristic relaxation times vary exponentially with temperature, changing by a factor of 2 for each 2 °C change in temperature. At low wavevectors, the measured relaxations are diffusive with relaxation times that change by a factor of 2 for each 8 °C change in temperature.

  6. Hybrid, Nanoscale Phospholipid/Block Copolymer Vesicles

    Directory of Open Access Journals (Sweden)

    Bo Liedberg

    2013-09-01

    Full Text Available Hybrid phospholipid/block copolymer vesicles, in which the polymeric membrane is blended with phospholipids, display interesting self-assembly behavior, incorporating the robustness and chemical versatility of polymersomes with the softness and biocompatibility of liposomes. Such structures can be conveniently characterized by preparing giant unilamellar vesicles (GUVs via electroformation. Here, we are interested in exploring the self-assembly and properties of the analogous nanoscale hybrid vesicles (ca. 100 nm in diameter of the same composition prepared by film-hydration and extrusion. We show that the self-assembly and content-release behavior of nanoscale polybutadiene-b-poly(ethylene oxide (PB-PEO/1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidylcholine (POPC hybrid phospholipid/block copolymer vesicles can be tuned by the mixing ratio of the amphiphiles. In brief, these hybrids may provide alternative tools for drug delivery purposes and molecular imaging/sensing applications and clearly open up new avenues for further investigation.

  7. Monte Carlo simulations of the phase separation of a copolymer blend in a thin film

    KAUST Repository

    Wang, Zhexiao

    2014-12-11

    Monte Carlo simulations were carried out to study the phase separation of a copolymer blend comprising an alternating copolymer and/or block copolymer in a thin film, and a phase diagram was constructed with a series of composed recipes. The effects of composition and segregation strength on phase separation were discussed in detail. The chain conformation of the block copolymer and alternating copolymer were investigated with changes of the segregation strength. Our simulations revealed that the segment distribution along the copolymer chain and the segregation strength between coarse-grained beads are two important parameters controlling phase separation and chain conformation in thin films of a copolymer blend. A well-controlled phase separation in the copolymer blend can be used to fabricate novel nanostructures.

  8. From Block Copolymers to Nano-porous Materials

    DEFF Research Database (Denmark)

    Vigild, Martin Etchells; Ndoni, Sokol; Berg, Rolf Henrik

    2003-01-01

    Quantitative etching of the polydimethylsiloxane block in a series of polystyrene-polydimethylsiloxane (PS-PDMS) block copolymers is reported. Reacting the block copolymer with anhydrous hydrogen fluoride (HF) renders a nanoporous material with the remaining PS maintaining the original morphology...

  9. Ion Transport in Nanostructured Block Copolymer/Ionic Liquid Membranes

    OpenAIRE

    Hoarfrost, Megan Lane

    2012-01-01

    Incorporating an ionic liquid into one block copolymer microphase provides a platform for combining the outstanding electrochemical properties of ionic liquids with a number of favorable attributes provided by block copolymers. In particular, block copolymers thermodynamically self-assemble into well-ordered nanostructures, which can be engineered to provide a durable mechanical scaffold and template the ionic liquid into continuous ion-conducting nanochannels. Understanding how the additio...

  10. Responsive block copolymer photonics triggered by protein-polyelectrolyte coacervation.

    Science.gov (United States)

    Fan, Yin; Tang, Shengchang; Thomas, Edwin L; Olsen, Bradley D

    2014-11-25

    Ionic interactions between proteins and polyelectrolytes are demonstrated as a method to trigger responsive transitions in block copolymer (BCP) photonic gels containing one neutral hydrophobic block and one cationic hydrophilic block. Poly(2-vinylpyridine) (P2VP) blocks in lamellar poly(styrene-b-2-vinylpyridine) block copolymer thin films are quaternized with primary bromides to yield swollen gels that show strong reflectivity peaks in the visible range; exposure to aqueous solutions of various proteins alters the swelling ratios of the quaternized P2VP (QP2VP) gel layers in the PS-QP2VP materials due to the ionic interactions between proteins and the polyelectrolyte. Parameters such as charge density, hydrophobicity, and cross-link density of the QP2VP gel layers as well as the charge and size of the proteins play significant roles on the photonic responses of the BCP gels. Differences in the size and pH-dependent charge of proteins provide a basis for fingerprinting proteins based on their temporal and equilibrium photonic response. The results demonstrate that the BCP gels and their photonic effect provide a robust and visually interpretable method to differentiate different proteins. PMID:25393374

  11. Perspective: Evolutionary design of granular media and block copolymer patterns

    Science.gov (United States)

    Jaeger, Heinrich M.; de Pablo, Juan J.

    2016-05-01

    The creation of new materials "by design" is a process that starts from desired materials properties and proceeds to identify requirements for the constituent components. Such process is challenging because it inverts the typical modeling approach, which starts from given micro-level components to predict macro-level properties. We describe how to tackle this inverse problem using concepts from evolutionary computation. These concepts have widespread applicability and open up new opportunities for design as well as discovery. Here we apply them to design tasks involving two very different classes of soft materials, shape-optimized granular media and nanopatterned block copolymer thin films.

  12. Surface tension of micellar block copolymer films

    International Nuclear Information System (INIS)

    Surface tensions of micellar block copolymers of poly(styrene-b-dimethylsiloxane) (PS-b-PDMS) films are obtained by X-ray diffuse scattering. PS-b-PDMS films on Si substrates with the thicknesses from 36 to 588 nm were investigated at temperatures of 30 - 215 .deg. C. The surface tension reflects the concentration of PDMS micelles which are preferably located at the surface. The molar fraction of PDMS micelles near the surface is estimated by using angle-resolved X-ray photoelectron spectroscopy.

  13. Oriented Protein Nanoarrays on Block Copolymer Template.

    Science.gov (United States)

    Shen, Lei; Zhu, Jintao

    2016-03-01

    Here, a simple yet robust method is developed to fabricate oriented protein nanoarrays by employing a block copolymer (BCP) template, which presents nano-scaled spot areas at high-density arrays. Unlike the conventional BCP nanolithography, the BCP platform described here resists nonspecific protein adsorption and prevents the denaturation of immobilized proteins in aqueous solution. The orderly arranged array areas are functionalized by linking chemistry which allows for the precise control of protein orientation. This approach allows us to generate potentially oriented protein nanoarrays at high-density array spots, which is useful for miniaturized nanoarrays within high-throughput proteomic applications. PMID:26785818

  14. Synthesis and Morphological Characterization of Block Copolymers for Improved Biomaterials

    OpenAIRE

    Schricker, Scott; Palacio, Manuel; Thirumamagal, B.T.S.; Bhushan, Bharat

    2010-01-01

    Biocompatible polymers are known to act as scaffolds for the regeneration and growth of bone. Block copolymers are of interest as scaffold materials because a number of the blocks are biocompatible, and their nanostructure is easily tunable with synthetic techniques. In this paper, we report the synthesis of a novel class of biomaterials from block copolymers containing a hydrophobic block of methyl methacrylate and a hydrophilic block of either acrylic acid, dimethyl acrylamide, or 2-hydroxy...

  15. Interface-enforced complexation between copolymer blocks.

    Science.gov (United States)

    Steinschulte, Alexander A; Xu, Weinan; Draber, Fabian; Hebbeker, Pascal; Jung, Andre; Bogdanovski, Dimitri; Schneider, Stefanie; Tsukruk, Vladimir V; Plamper, Felix A

    2015-05-14

    Binary diblock copolymers and corresponding ternary miktoarm stars are studied at oil-water interfaces. All polymers contain oil-soluble poly(propylene oxide) PPO, water-soluble poly(dimethylaminoethyl methacrylate) PDMAEMA and/or poly(ethylene oxide) PEO. The features of their Langmuir compression isotherms are well related to the ones of the corresponding homopolymers. Within the Langmuir-trough, PEO-b-PPO acts as the most effective amphiphile compared to the other PPO-containing copolymers. In contrast, the compression isotherms show a complexation of PPO and PDMAEMA for PPO-b-PDMAEMA and the star, reducing their overall amphiphilicity. Such complex formation between the blocks of PPO-b-PDMAEMA is prevented in bulk water but facilitated at the interface. The weakly-interacting blocks of PPO-b-PDMAEMA form a complex due to their enhanced proximity in such confined environments. Scanning force microscopy and Monte Carlo simulations with varying confinement support our results, which are regarded as compliant with the mathematical random walk theorem by Pólya. Finally, the results are expected to be of relevance for e.g. emulsion formulation and macromolecular engineering. PMID:25807174

  16. Controlling Structure in Sulfonated Block Copolymer Membranes

    Science.gov (United States)

    Truong, Phuc; Stein, Gila; Strzalka, Joe

    2015-03-01

    In many ionic block copolymer systems, the strong incompatibility between ionic and non-ionic segments will trap non-equilibrium structures in the film, making it difficult to engineer the optimal domain sizes and transport pathways. The goal of this work is to establish a framework for controlling the solid-state structure of sulfonated pentablock copolymer membranes. They have ABCBA block sequence, where A is poly(t-butyl styrene), B is poly(hydrogenated isoprene), and C is poly(styrene sulfonate). To process into films, the polymer is dissolved in toluene/n-propanol solvent mixtures, where the solvent proportions and the polymer loading were both varied. Solution-state structure was measured with small angle X-ray scattering (SAXS). We detected micelles with radii that depend on the solvent composition and polymer loading. Film structure was measured with grazing-incidence SAXS, which shows (i) domain periodicity is constant throughout film thickness; (ii) domain periodicity depends on solvent composition and polymer loading, and approximately matches the micelle radii in solutions. The solid-state packing is consistent with a hard sphere structure factor. Results suggest that solid-state structure can be tuned by manipulating the solution-state self-assembly.

  17. Self-assembled materials from thermosensitive and biohybrid block copolymers

    NARCIS (Netherlands)

    de Graaf, A.J.

    2012-01-01

    In this research, several block copolymers were synthesized and characterized with regard to possible pharmaceutical applications. All block copolymers were thermosensitive and self-assembled at 37 °C into structures like micelles and hydrogels, which can be used for innovative drug delivery purpose

  18. Synthesis and Characterization of Novel Magnetite Nanoparticle Block Copolymer Complexes

    OpenAIRE

    Zhang, Qian

    2007-01-01

    Superparamagnetic Magnetite (Fe3O4) nanoparticles were synthesized and complexed with carboxylate-functionalized block copolymers, and aqueous dispersions of the complexes were investigated as functions of their chemical and morphological structures. The block copolymer dispersants possessed either poly(ethylene oxide), poly(ethylene oxide-co-propylene oxide), or poly(ethylene oxide-b-propylene oxide) outer blocks, and all contained a polyurethane center block with pendant carboxylate functi...

  19. Anomalous Micellization of Pluronic Block Copolymers

    Science.gov (United States)

    Leonardi, Amanda; Ryu, Chang Y.

    2014-03-01

    Poly(ethylene oxide) - poly(propylene oxide) - poly(ethylene oxide) (PEO-PPO-PEO) block copolymers, commercially known as Pluronics, are a unique family of amphiphilic triblock polymers, which self-assemble into micelles in aqueous solution. These copolymers have shown promise in therapeutic, biomedical, cosmetic, and nanotech applications. As-received samples of Pluronics contain low molecular weight impurities (introduced during the manufacturing and processing), that are ignored in most applications. It has been observed, however, that in semi-dilute aqueous solutions, at concentrations above 1 wt%, the temperature dependent micellization behavior of the Pluronics is altered. Anomalous behavior includes a shift of the critical micellization temperature and formation of large aggregates at intermediate temperatures before stable sized micelles form. We attribute this behavior to the low molecular weight impurities that are inherent to the Pluronics which interfere with the micellization process. Through the use of Dynamic Light Scattering and HPLC, we compared the anomalous behavior of different Pluronics of different impurity levels to their purified counterparts.

  20. Block copolymer ion gels for gas separation

    Science.gov (United States)

    Gu, Yuanyan; Lodge, Timothy

    2012-02-01

    Carbon dioxide removal from light gases (eg. N2, CH4, and H2) is a very important technology for industrial applications such as natural gas sweetening, CO2 capture from coal-fire power plant exhausts and hydrogen production. Current CO2 separation method uses amine-absorption, which is energy-intensive and requires frequent maintenance. Membrane separation is a cost-effective solution to this problem, especially in small-scale applications. Ionic liquids have recently received increasing interest in this area because of their selective solubility for CO2 and non-volatility. However, ionic liquid itself lacks the persistent structure and mechanical integrity to withstand the high pressure for gas separation. Here, we report the development and gas separation performances of physically crosslinked ion gels based on self-assembly of ABA-triblock copolymers in ionic liquids. Three different types of polymers was used to achieve gelation in ionic liquids. Specifically, a triblock copolymer ion gel with a polymerized ionic liquid mid-block shows performances higher than the upper bound of well-known ``Robeson Plot'' for CO2/N2.

  1. Synthesis and morphological characterization of block copolymers for improved biomaterials

    International Nuclear Information System (INIS)

    Biocompatible polymers are known to act as scaffolds for the regeneration and growth of bone. Block copolymers are of interest as scaffold materials because a number of the blocks are biocompatible, and their nanostructure is easily tunable with synthetic techniques. In this paper, we report the synthesis of a novel class of biomaterials from block copolymers containing a hydrophobic block of methyl methacrylate and a hydrophilic block of either acrylic acid, dimethyl acrylamide, or 2-hydroxyethyl methacrylate. The block copolymers were synthesized using a combination of reversible addition-fragmentation chain transfer (RAFT) polymerization and click chemistry. Since the surface morphology is critical for successful cell growth, atomic force microscopy (AFM) studies were conducted for selected block copolymers. The topography, phase angle and friction maps were obtained in dry and physiological buffer environments to study the morphology. Results of AFM imaging identified the presence of polymer domains corresponding to the copolymer components. The distribution of nanoscale features in these block copolymers is comparable to those found on other surfaces that exhibit favorable cell adhesion and growth. In physiological buffer medium, the hydrophilic component of the block copolymer (acrylic acid or hydroxyethyl methacrylate) appears to be present in greater amounts on the surface as a consequence of water absorption and swelling.

  2. Synthesis and morphological characterization of block copolymers for improved biomaterials

    Energy Technology Data Exchange (ETDEWEB)

    Schricker, Scott, E-mail: Schricker.1@osu.edu [Restorative and Prosthetic Dentistry Section, College of Dentistry, The Ohio State University, Columbus, OH 43210 (United States); Palacio, Manuel [Nanoprobe Laboratory for Bio- and Nanotechnology and Biomimetics, The Ohio State University, Columbus, OH 43210 (United States); Thirumamagal, B.T.S. [Restorative and Prosthetic Dentistry Section, College of Dentistry, The Ohio State University, Columbus, OH 43210 (United States); Bhushan, Bharat [Nanoprobe Laboratory for Bio- and Nanotechnology and Biomimetics, The Ohio State University, Columbus, OH 43210 (United States)

    2010-05-15

    Biocompatible polymers are known to act as scaffolds for the regeneration and growth of bone. Block copolymers are of interest as scaffold materials because a number of the blocks are biocompatible, and their nanostructure is easily tunable with synthetic techniques. In this paper, we report the synthesis of a novel class of biomaterials from block copolymers containing a hydrophobic block of methyl methacrylate and a hydrophilic block of either acrylic acid, dimethyl acrylamide, or 2-hydroxyethyl methacrylate. The block copolymers were synthesized using a combination of reversible addition-fragmentation chain transfer (RAFT) polymerization and click chemistry. Since the surface morphology is critical for successful cell growth, atomic force microscopy (AFM) studies were conducted for selected block copolymers. The topography, phase angle and friction maps were obtained in dry and physiological buffer environments to study the morphology. Results of AFM imaging identified the presence of polymer domains corresponding to the copolymer components. The distribution of nanoscale features in these block copolymers is comparable to those found on other surfaces that exhibit favorable cell adhesion and growth. In physiological buffer medium, the hydrophilic component of the block copolymer (acrylic acid or hydroxyethyl methacrylate) appears to be present in greater amounts on the surface as a consequence of water absorption and swelling.

  3. Block Copolymer Metastability: Scientific Nightmare or Engineering Dream?

    Science.gov (United States)

    Bates, Frank S.

    1997-03-01

    Most experimental studies and almost all theories that deal with block copolymers, or mixtures of block copolymers and homopolymers, have been designed from an equilibrium perspective. Yet a myriad of factors conspire to retard approach to equilibrium in these systems, including: subtle features in the free energy surface that are controlled by ordered state symmetry; a coupling between microphase separation and entanglement dynamics; complex molecular architectures such as multiblock, starblock, and miktoarm. Even unentangled low molecular weight diblock copolymers, the simplest and dynamically least encumbered materials, exhibit long-lived metastable states that confound attempts to validate equilibrium theories. However, this apparent dilemma can be exploited through clever processing strategies. This lecture will address two opposing consequences of block copolymer metastability. The first is a potential nightmare: Can we ever establish universal block copolymer phase diagrams? The second is the stuff of dreams: Self-assembled thermoset nanocomposites.

  4. Multicompartment Micelles From π-Shaped ABC Block Copolymers

    Institute of Scientific and Technical Information of China (English)

    XIA Jun; ZHONG Chong-Li

    2007-01-01

    Dissipative particle dynamics simulations were performed on the morphology and structure of multicompartment micelles formed from n-shaped ABC block copolymers in water. The influences of chain architectures were studied in a systematic way, and a rich variety of morphologies were observed, such as spherical, wormlike,X-shaped, Y-shaped, ribbon-like, layered rod-like, layered disk-like, as well as network morphologies. The simulations show that the distance between the two grafts plays an important role in control of the morphology. Since π-shaped ABC block copolymers can be reduced to linear ABC and star ABC block copolymers, they are good model copolymers for studying the self-assembly of complex block copolymers into micelles. The knowledge obtained in this work as well as the new morphologies identified provide useful information for future rational design and synthesis of novel multicompartment micelles.

  5. Pattern Transfer of Sub-10 nm Features via Tin-Containing Block Copolymers

    OpenAIRE

    Maher, Michael J.; Mori, Kazunori; Sirard, Stephen M.; Dinhobl, Andrew M.; Bates, Christopher M.; Gurer, Emir; Blachut, Gregory; Lane, Austin P.; Durand, William J.; Carlson, Matthew C.; Strahan, Jeffrey R.; Ellison, Christopher J.; Willson, C. Grant

    2016-01-01

    Tin-containing block copolymers were investigated as materials for nanolithographic applications. Poly(4-trimethylstannylstyrene-block-styrene) (PSnS-PS) and poly(4-trimethylstannylstyrene-block-4-methoxystyrene) (PSnS-PMOST) synthesized by reversible addition–fragmentation chain transfer polymerization form lamellar domains with periodicities ranging from 18 to 34 nm. Thin film orientation control was achieved by thermal annealing between a neutral surface treatment and a top coat. Incorpora...

  6. Morphological studies on block copolymer modified PA 6 blends

    Energy Technology Data Exchange (ETDEWEB)

    Poindl, M., E-mail: marcus.poindl@ikt.uni-stuttgart.de, E-mail: christian.bonten@ikt.uni-stuttgart.de; Bonten, C., E-mail: marcus.poindl@ikt.uni-stuttgart.de, E-mail: christian.bonten@ikt.uni-stuttgart.de [Institut für Kunststofftechnik, University of Stuttgart (Germany)

    2014-05-15

    Recent studies show that compounding polyamide 6 (PA 6) with a PA 6 polyether block copolymers made by reaction injection molding (RIM) or continuous anionic polymerization in a reactive extrusion process (REX) result in blends with high impact strength and high stiffness compared to conventional rubber blends. In this paper, different high impact PA 6 blends were prepared using a twin screw extruder. The different impact modifiers were an ethylene propylene copolymer, a PA PA 6 polyether block copolymer made by reaction injection molding and one made by reactive extrusion. To ensure good particle matrix bonding, the ethylene propylene copolymer was grafted with maleic anhydride (EPR-g-MA). Due to the molecular structure of the two block copolymers, a coupling agent was not necessary. The block copolymers are semi-crystalline and partially cross-linked in contrast to commonly used amorphous rubbers which are usually uncured. The combination of different analysis methods like atomic force microscopy (AFM), transmission electron microscopy (TEM) and scanning electron microscopy (SEM) gave a detailed view in the structure of the blends. Due to the partial cross-linking, the particles of the block copolymers in the blends are not spherical like the ones of ethylene propylene copolymer. The differences in molecular structure, miscibility and grafting of the impact modifiers result in different mechanical properties and different blend morphologies.

  7. Molecular Transfer Printing Using Block Copolymers

    Science.gov (United States)

    Ji, Shengxiang; Liu, Chi-Chun; Liu, Guoliang; Nealey, Paul

    2009-03-01

    We report a new parallel patterning technique, molecular transfer printing (MTP), for replicating geometrically complex patterns over macroscopic areas with sub-15 nm feature dimensions, and the ability to replicate the same pattern multiple times. In MTP, inks are mixed with block copolymers (BCPs) and deposited as films on a substrate. The inks are compatible with only one block of the BCP, and sequestered into domains of nanometer scale dimensions after microphase separation. A second substrate is then placed in contact with the surface of the film. By designing the inks to react, adsorb, or otherwise interact with the second substrate, inks are transferred to the second substrate in the exact pattern of domains present at the surface of the ``master'' BCP film. Here we demonstrate high degrees of perfection on both line and dot patterns. We also show that 1) the master template can be regenerated, 2) the resultant replica can be used to direct the assembly of BCPs and as a daughter master for MTP, and 3) the master and daughter templates can be reused tens of times.

  8. Hollow ZIF-8 Nanoworms from Block Copolymer Templates

    KAUST Repository

    Yu, Haizhou

    2015-10-16

    Recently two quite different types of “nano-containers” have been recognized as attractive potential drug carriers; these are wormlike filamenteous micelles (“filomicelles”) on the one hand and metal organic frameworks on the other hand. In this work we combine these two concepts. We report for the first time the manufacturing of metal organic framework nanotubes with a hollow core. These worm-like tubes are about 200 nm thick and several μm long. The preparation is simple: we first produce long and flexible filament-shaped micelles by block copolymer self-assembly. These filomicelles serve as templates to grow a very thin layer of interconnected ZIF-8 crystals on their surface. Finally the block copolymer is removed by solvent extraction and the hollow ZIF-8 nanotubes remain. These ZIF-NTs are surprisingly stable and withstand purification by centrifugation. The synthesis method is straightforward and can easily be applied for other metal organic framework materials. The ZIF-8 NTs exhibit high loading capacity for the model anti cancer drug doxorubicin (DOX) with a pH-triggered release. Hence, a prolonged circulation in the blood stream and a targeted drug release behavior can be expected.

  9. Functional Block Copolymers via Anionic Polymerization for Electroactive Membranes

    OpenAIRE

    Schultz, Alison

    2013-01-01

           Ion-containing block copolymers blend ionic liquid properties with well-defined polymer architectures. This provides conductive materials with robust mechanical stability, efficient processability, and tunable macromolecular design. Conventional free radical polymerization and anion exchange achieved copolymers containing n-butyl acrylate and phosphonium ionic liquids. These compositions incorporated vinylbenzyl triphenyl phosphonium and vinylbenzyl tricyclohexyl phosphonium cations be...

  10. Radiation crosslinked block copolymer blends with improved impact resistance

    International Nuclear Information System (INIS)

    Polymer blends having high impact resistance after mechanical working are produced by blending together a non-elastomeric monovinylidene aromatic polymer such as polystyrene with an elastomeric copolymer, such as a block copolymer of styrene and butadiene, in the form of crosslinked, colloidal size particles

  11. Stereo block copolymers of L- and D-lactides

    NARCIS (Netherlands)

    Yui, Nobuhiko; Dijkstra, Pieter J.; Feijen, Jan

    1990-01-01

    Sequential diblock copolymers composed of L- and D-lactic acid residues were synthesized through a living ring-opening polymerization of L- and D-lactide initiated by aluminium tris(2-propanolate). The composition of the block copolymers was varied by changing the reaction conditions and monomer ove

  12. Synthesis of Amylose-b-P2 VP Block Copolymers.

    Science.gov (United States)

    Kumar, Kamlesh; Woortman, Albert J J; Loos, Katja

    2015-12-01

    A new class of rod-coil block copolymers is synthesized by chemoenzymatic polymerization. In the first step, maltoheptaose, which acts as a primer for the synthesis of amylose, is attached to poly(2-vinyl pyridine) (P2 VP). The enzymatic polymerization of maltoheptaose is carried out by phosphorylase to obtain amylose-b-P2 VP block copolymers. The block copolymer is characterized by Fourier transform infrared spectroscopy, nuclear magnetic resonance, gel permeation chromatography, and wide-angle X-ray scattering techniques. The designed molecules combine the inclusion complexation ability of amylose with the supramolecular complexation ability of P2 VP and therefore this kind of rod-coil block copolymers can be used to generate well-organized novel self-assembled structures. PMID:26437256

  13. Correlative infrared nanospectroscopic and nanomechanical imaging of block copolymer microdomains.

    Science.gov (United States)

    Pollard, Benjamin; Raschke, Markus B

    2016-01-01

    Intermolecular interactions and nanoscale phase separation govern the properties of many molecular soft-matter systems. Here, we combine infrared vibrational scattering scanning near-field optical microscopy (IR s-SNOM) with force-distance spectroscopy for simultaneous characterization of both nanoscale optical and nanomechanical molecular properties through hybrid imaging. The resulting multichannel images and correlative analysis of chemical composition, spectral IR line shape, modulus, adhesion, deformation, and dissipation acquired for a thin film of a nanophase separated block copolymer (PS-b-PMMA) reveal complex structural variations, in particular at domain interfaces, not resolved in any individual signal channel alone. These variations suggest that regions of multicomponent chemical composition, such as the interfacial mixing regions between microdomains, are correlated with high spatial heterogeneity in nanoscale material properties. PMID:27335750

  14. Ionic Block Copolymers for Anion Exchange Membranes

    Science.gov (United States)

    Tsai, Tsung-Han; Herbst, Dan; Giffin, Guinevere A.; di Noto, Vito; Witten, Tom; Coughlin, E. Bryan

    2013-03-01

    Anion exchange membrane (AEM) fuel cells have regained interest because it allows the use of non-noble metal catalysts. Until now, most of the studies on AEM were based on random polyelectrolytes. In this work, Poly(vinylbenzyltrimethylammonium bromide)-b- (methylbutylene) ([PVBTMA][Br]-b-PMB) was studied by SAXS, TEM and dielectric spectroscopy to understand the fundamental structure-conductivity relationship of ion transport mechanisms within well-ordered block copolymers. The ionic conductivity and the formation of order structure were dependent on the casting solvent. Higher ion exchange capacity (IEC) of the membranes showed higher conductivity at as IEC values below 1.8mmol/g, as above this, the ionic conductivity decreases due to more water uptake leading to dilution of charge density. The humidity dependence of morphology exhibited the shifting of d-spacing to higher value and the alteration in higher characteristic peak of SAXS plot as the humidity increase from the dry to wet state. This phenomenon can be further explained by a newly developed polymer brush theory. Three ionic conduction pathways with different conduction mechanism within the membranes can be confirmed by broadband electric spectroscopy. US Army MURI (W911NF1010520)

  15. Adsorption of semiflexible block copolymers on homogeneous surfaces

    OpenAIRE

    Cerdà, Joan J.; Sintes, Tomàs; Sumithra, K.

    2005-01-01

    We present the results of extensive numerical off-lattice Monte Carlo simulations of semiflexible block-copolymer chains adsorbed onto flat homogeneous surfaces. We have compared the behavior of several chain structures, such as homopolymers, diblocks, (AαBα) block copolymers, and random heteropolymers. In all the cases studied, we have found the adsorption process to be favored with an increase of the chain rigidity. Particularly, the adsorption of diblock structures becomes a two-step proce...

  16. Aggregation behavior of water-soluble amphiphilic block copolymers

    OpenAIRE

    Bonné, Tune Bjarke

    2007-01-01

    Polymers and block copolymers based on 2-alkyl-2-oxazoline have the advantage that their hydrophobicity can be varied by changing the length of the alkyl side chain and that fluorescence groups can be attached to the block ends. We have studied the aggregation behavior of 2-alkyl-2-oxazoline based diblock, triblock and random copolymers in aqueous solutions, using fluorescence correlation spectroscopy (FCS), where fluorescence labeled polymers were used as tracers. FCS experiments in combinat...

  17. Self-assembled materials from thermosensitive and biohybrid block copolymers

    OpenAIRE

    De Graaf, A.J.

    2012-01-01

    In this research, several block copolymers were synthesized and characterized with regard to possible pharmaceutical applications. All block copolymers were thermosensitive and self-assembled at 37 °C into structures like micelles and hydrogels, which can be used for innovative drug delivery purposes. Some of the synthesized polymers were biohybrid, in the sense that they contained peptide segments which enabled their cleavage by enzymes that are upregulated in diseased tissues. First, method...

  18. New adhesive systems based on functionalized block copolymers

    Energy Technology Data Exchange (ETDEWEB)

    Kent, M.; Saunders, R.; Hurst, M.; Small, J.; Emerson, J.; Zamora, D.

    1997-05-01

    The goal of this work was to evaluate chemically-functionalized block copolymers as adhesion promoters for metal/thermoset resin interfaces. Novel block copolymers were synthesized which contain pendant functional groups reactive toward copper and epoxy resins. In particular, imidazole and triazole functionalities that chelate with copper were incorporated onto one block, while secondary amines were incorporated onto the second block. These copolymers were found to self-assemble from solution onto copper surfaces to form monolayers. The structure of the adsorbed monolayers were studied in detail by neutron reflection and time-of-flight secondary ion mass spectrometry. The monolayer structure was found to vary markedly with the solution conditions and adsorption protocol. Appropriate conditions were found for which the two blocks form separate layers on the surface with the amine functionalized block exposed at the air surface. Adhesion testing of block copolymer-coated copper with epoxy resins was performed in both lap shear and peel modes. Modest enhancements in bond strengths were observed with the block copolymer applied to the native oxide. However, it was discovered that the native oxide is the weak link, and that by simply removing the native oxide, and then applying an epoxy resin before the native oxide can reform, excellent bond strength in the as-prepared state as well as excellent retention of bond strength after exposure to solder in ambient conditions are obtained. It is recommended that long term aging studies be performed with and without the block copolymer. In addition, the functionalized block copolymer method should be evaluated for another system that has inherently poor bonding, such as the nickel/silicone interface, and for systems involving metals and alloys which form oxides very rapidly, such as aluminum and stainless steel, where bonding strategies involve stabilizing the native oxide.

  19. New routes to the synthesis of amylose-block-polystyrene rod-coil block copolymers

    NARCIS (Netherlands)

    Loos, Katja; Müller, Axel H.E.

    2002-01-01

    Hybrid block copolymers amylose-block-polystyrene were synthesized by covalent attachment of maltoheptaose derivatives to end-functionalized polystyrene and subsequent enzymatic grafting from polymerization. The maltoheptaose derivatives were attached by reductive amination or hydrosilation to amino

  20. Perpendicularly Aligned, Anion Conducting Nanochannels in Block Copolymer Electrolyte Films

    Energy Technology Data Exchange (ETDEWEB)

    Arges, Christopher G.; Kambe, Yu; Suh, Hyo Seon; Ocola, Leonidas E.; Nealey, Paul F.

    2016-03-08

    Connecting structure and morphology to bulk transport properties, such as ionic conductivity, in nanostructured polymer electrolyte materials is a difficult proposition because of the challenge to precisely and accurately control order and the orientation of the ionic domains in such polymeric films. In this work, poly(styrene-block-2-vinylpyridine) (PSbP2VP) block copolymers were assembled perpendicularly to a substrate surface over large areas through chemical surface modification at the substrate and utilizing a versatile solvent vapor annealing (SVA) technique. After block copolymer assembly, a novel chemical vapor infiltration reaction (CVIR) technique selectively converted the 2-vinylpyridine block to 2-vinyl n-methylpyridinium (NMP+ X-) groups, which are anion charge carriers. The prepared block copolymer electrolytes maintained their orientation and ordered nanostructure upon the selective introduction of ion moieties into the P2VP block and post ion-exchange to other counterion forms (X- = chloride, hydroxide, etc.). The prepared block copolymer electrolyte films demonstrated high chloride ion conductivities, 45 mS cm(-1) at 20 degrees C in deionized water, the highest chloride ion conductivity for anion conducting polymer electrolyte films. Additionally, straight-line lamellae of block copolymer electrolytes were realized using chemoepitaxy and density multiplication. The devised scheme allowed for precise and accurate control of orientation of ionic domains in nanostructured polymer electrolyte films and enables a platform for future studies that examines the relationship between polymer electrolyte structure and ion transport.

  1. Block Copolymers of Ethylene Oxide and Styrene Oxide.New Copolymer Surfactants(Ⅱ)

    Institute of Scientific and Technical Information of China (English)

    Zhuo Yang; David Attwood; Colin Booth

    2003-01-01

    @@ 3.2. Association Number Figure 5 shows the dependence of the weight-average association number (Nw,measured by static light scattering, solution temperature 30 °C) on hydrophobe block length for ES and ESEblock copolymers.

  2. Selective Semiconductor Nanocluster Deposition on Eptaxially Patterned Semicrystalline Block Copolymer Film

    Science.gov (United States)

    Park, Cheolmin; Lee, Jinwook; Jensen, Klavs F.; Bawendi, Moungi G.; Thomas, Edwin L.

    2001-03-01

    Monodisperse ZnS encapsulated CdSe semiconductor nanoclusters are sequestered in between the crystalline polyethylene (PE) lamellae of poly (ethylene-b-ethylene-alt-propylene-b ethylene) semicrystalline triblock copolymer epitaxially crystallized on single crystal of anthracene (AN). Epitaxy between PE block and An created a cross oriented texture of the edge-on crystalline PE lamellae in the thin film. At the same time, the nanoclusters, initially dissolved in the mixture of block copolymer and AN, were rejected out of the crystalline lamellae during epitaxial crystallization and selectively deposited in the amorphous region of the block copolymer. Selective distribution of nanoclusters on the cross oriented pattern structure is clearly evidenced by selected area diffraction (SAD) and bright field transmission electron microscope (TEM).

  3. Sub-15nm Silicon Lines Fabrication via PS-b-PDMS Block Copolymer Lithography

    OpenAIRE

    Sozaraj Rasappa; Lars Schulte; Dipu Borah; Morris, Michael A.; Sokol Ndoni

    2013-01-01

    This paper describes the fabrication of nanodimensioned silicon structures on silicon wafers from thin films of a poly(styrene)-block-poly(dimethylsiloxane) (PS-b-PDMS) block copolymer (BCP) precursor self-assembling into cylindrical morphology in the bulk. The structure alignment of the PS-b-PDMS (33 k–17 k) was conditioned by applying solvent and solvothermal annealingtechniques. BCP nanopatterns formed after the annealing process have been confirmed by scanning electron microscope (SEM) af...

  4. Fluorinated polyphenylenevinylene (PPV) block co-polymers for nanophotonics

    Science.gov (United States)

    Sun, Sam-Shajing; Nguyen, Thuong; Brooks, Jaleesa

    2013-09-01

    Polymer based optoelectronic materials and thin film devices exhibit great potential in future space applications due to their flexibility, light weight, large light absorption coefficient, and promising radiation tolerance in space environment as compared to their inorganic semiconductor counterparts. Since carbon-fluorine (C-F) chemical bonds are much stronger than the carbon-hydrogen (C-H) bonds, fluorinated polymer films offer great potential for space applications due their expected resistance to oxidation, thermal stability, excellent wear properties, and low coefficients of friction. Their use in a space environment is extremely attractive since they are expected to retain their lubricating characteristics in vacuum, unlike many solid lubricants. Current existing polymer photovoltaic materials and devices suffer low photoelectric power conversion efficiencies due to a number factors including poor morphologies at nano scale that hinder the charge separation and transport. This paper reports our recent work on a fluorinated DBfA type block copolymer system where the donor (D) block contains a donor substituted and hydrocarbon based polyphenylenevinylene (PPV), acceptor (fA) block contains a fluorinated and a sulfone acceptor substituted polyphenylenevinylene (f-PPV), and B is a non-conjugated and flexible bridge unit. Preliminary studies reveal DBfA exhibits better nano phase morphologies and over 100 times more efficient optoelectronic conversion efficiencies as compared to D/fA blend.

  5. Solubility and self-assembly of amphiphilic gradient and block copolymers in supercritical CO2

    International Nuclear Information System (INIS)

    This work aims at demonstrating the interest of gradient copolymers in supercritical CO2 in comparison with block copolymers. Gradient copolymers exhibit a better solubility in supercritical CO2 than block copolymers, as attested by cloud point data. The self-assembly of gradient and block copolymers in dense CO2 has been characterized by Small-Angle Neutron Scattering (SANS); and it is shown that it is not fundamentally modified when changing from block copolymers to gradient copolymers. Therefore, gradient copolymers are advantageous thanks to their easier synthesis and their solubility at lower pressure while maintaining a good ability for self-organization in dense CO2. (authors)

  6. Using click chemistry to modify block copolymers and their morphologies

    Science.gov (United States)

    Wollbold, Johannes

    Microphase separated block copolymers (BCPs) are emerging as promising templates and scaffolds for the fabrication of nanostructured materials. To achieve the desired nanostructures, it is necessary to establish convenient approaches to control the morphology of BCPs. It remains challenging to induce morphological transitions of BCPs via external fields. Click chemistry, especially alkyne/azide click chemistry, has been widely used to synthesize novel functionalized materials. Here, we demonstrate that alkyne/azide click chemistry can be used as an efficient approach to chemically modify BCPs and therefore induce morphological transitions. Alkyne-functionalized diblock copolymers (di-BCPs) poly(ethylene oxide)- block-poly(n-butyl methacrylate-random-propargyl methacrylate) (PEO-b-P(nBMA-r-PgMA)) have been successfully synthesized. When the di-BCP is blended with an azide additive Rhodamine B azide and annealed at elevated temperatures, click reaction occurs between the two components. With the Rhodamine B structure attached to the polymer backbone, the di-BCP shows dramatic change in the interactions between the two blocks and the volume fraction of each block. As a result, morphological transitions, such as disorder-to-order transitions (DOTs) and order-to-order transitions (OOTs), are observed. The reaction kinetics and morphology evolution during the click chemistry induced DOTs have been investigated by in-situ and ex-situ characterizations, and fast kinetics properties are observed. Microphase separated morphologies after the DOTs or OOTs are dictated by the composition of neat di-BCPs and the mole ratio between the alkyne and azide groups. The DOTs of PEO-b-P(nBMA-r-PgMA) di-BCPs induced by alkyne/azide click chemistry have also been achieved in thin film geometries, with comparable kinetics to bulk samples. The orientation of the microdomains is dependent on the grafting density of Rhodamine B structure as well as film thickness. At higher grafting densities

  7. Studies on microphase-separated structures of block copolymers by neutron reflectivity measurement

    International Nuclear Information System (INIS)

    Segmental distributions of block copolymer chains in lamellar microphase-separated structure and those of homopolymers in block copolymer/homopolymer blends also with lamellar structures were studied by neutron reflectivity measurements. It was revealed that polystyrene and poly(2-vinylpyridine) lamellae were alternately stacked within the thin films of pure block copolymers spin-coated on silicon wafers, and they were preferentially oriented along the direction parallel to film surface. Polystyrene lamella appeared at air surfaces of the films, while poly(2-vinylpyridine) lamella did on silicon surfaces. Segment distribution at lamellar interface was well described by an error function, and the width of the lamellar interface, defined by a full-width half-maximum value of interfacial profile, was estimated to be about 4.5 nm. Segments of block chains adjacent to the chemical junction points connecting different block chains were strongly localized near the lamellar interfaces, while those on the free ends of block chains were distributed all over the lamellar microdomains with their distribution maxima at the centers of lamellae. On the other hand, it was clarified that homopolymers dissolved in the corresponding lamellar microdomains of block copolymers were also distributed throughout the microdomains with their concentration maxima at the centers of the lamellae. (author)

  8. Ion Transport in Nanostructured Block Copolymer/Ionic Liquid Membranes

    Science.gov (United States)

    Hoarfrost, Megan Lane

    Incorporating an ionic liquid into one block copolymer microphase provides a platform for combining the outstanding electrochemical properties of ionic liquids with a number of favorable attributes provided by block copolymers. In particular, block copolymers thermodynamically self-assemble into well-ordered nanostructures, which can be engineered to provide a durable mechanical scaffold and template the ionic liquid into continuous ion-conducting nanochannels. Understanding how the addition of an ionic liquid affects the thermodynamic self-assembly of block copolymers, and how the confinement of ionic liquids to block copolymer nanodomains affects their ion-conducting properties is essential for predictable structure-property control. The lyotropic phase behavior of block copolymer/ionic liquid mixtures is shown to be reminiscent of mixtures of block copolymers with selective molecular solvents. A variety of ordered microstructures corresponding to lamellae, hexagonally close-packed cylinders, body-centered cubic, and face-centered cubic oriented micelles are observed in a model system composed of mixtures of imidazolium bis(trifluoromethylsulfonyl)imide ([Im][TFSI]) and poly(styrene- b-2-vinyl pyridine) (PS-b-P2VP). In contrast to block copolymer/molecular solvent mixtures, the interfacial area occupied by each PS-b-P2VP chain decreases upon the addition of [Im][TFSI], indicating a considerable increase in the effective segregation strength of the PS-b-P2VP copolymer with ionic liquid addition. The relationship between membrane structure and ionic conductivity is illuminated through the development of scaling relationships that describe the ionic conductivity of block copolymer/ionic liquid mixtures as a function of membrane composition and temperature. It is shown that the dominant variable influencing conductivity is the overall volume fraction of ionic liquid in the mixture, which means there is incredible freedom in designing the block copolymer architecture

  9. Ion and temperature sensitive polypeptide block copolymer.

    Science.gov (United States)

    Joo, Jae Hee; Ko, Du Young; Moon, Hyo Jung; Shinde, Usha Pramod; Park, Min Hee; Jeong, Byeongmoon

    2014-10-13

    A poly(ethylene glycol)/poly(L-alanine) multiblock copolymer incorporating ethylene diamine tetraacetic acid ([PA-PEG-PA-EDTA(m)) was synthesized as an ion/temperature dual stimuli-sensitive polymer, where the effect of different metal ions (Cu(2+), Zn(2+), and Ca(2+)) on the thermogelation of the polymer aqueous solution was investigated. The dissociation constants between the metal ions and the multiblock copolymer were calculated to be 1.2 × 10(-7), 6.6 × 10(-6), and 1.2 × 10(-4) M for Cu(2+), Zn(2+), and Ca(2+), respectively, implying that the binding affinity of the multiblock copolymer for Cu(2+) is much greater than that for Zn(2+) or Ca(2+). Atomic force microscopy and dynamic light scattering of the multiblock copolymer containing metal ions suggested micelle formation at low temperature, which aggregated as the temperature increased. Circular dichroism spectra suggested that changes in the α-helical secondary structure of the multiblock copolymer were more pronounced by adding Cu(2+) than other metal ions. The thermogelation of the multiblock copolymer aqueous solution containing Cu(2+) was observed at a lower temperature, and the modulus of the gel was significantly higher than that of the system containing Ca(2+) or Zn(2+), in spite of the same concentration of the metal ions and their same ionic valence of +2. The above results suggested that strong ionic complexes between Cu(2+) and the multiblock copolymer not only affected the secondary structure of the polymer but also facilitated the thermogelation of the polymer aqueous solution through effective salt-bridge formation even in a millimolar range of the metal ion concentration. Therefore, binding affinity of metal ions for polymers should be considered first in designing an effective ion/temperature dual stimuli-sensitive polymer. PMID:25178662

  10. Highly conductive side chain block copolymer anion exchange membranes.

    Science.gov (United States)

    Wang, Lizhu; Hickner, Michael A

    2016-06-28

    Block copolymers based on poly(styrene) having pendent trimethyl styrenylbutyl ammonium (with four carbon ring-ionic group alkyl linkers) or benzyltrimethyl ammonium groups with a methylene bridge between the ring and ionic group were synthesized by reversible addition-fragmentation radical (RAFT) polymerization as anion exchange membranes (AEMs). The C4 side chain polymer showed a 17% increase in Cl(-) conductivity of 33.7 mS cm(-1) compared to the benzyltrimethyl ammonium sample (28.9 mS cm(-1)) under the same conditions (IEC = 3.20 meq. g(-1), hydration number, λ = ∼7.0, cast from DMF/1-propanol (v/v = 3 : 1), relative humidity = 95%). As confirmed by small angle X-ray scattering (SAXS), the side chain block copolymers with tethered ammonium cations showed well-defined lamellar morphologies and a significant reduction in interdomain spacing compared to benzyltrimethyl ammonium containing block copolymers. The chemical stabilities of the block copolymers were evaluated under severe, accelerated conditions, and degradation was observed by (1)H NMR. The block copolymer with C4 side chain trimethyl styrenylbutyl ammonium motifs displayed slightly improved stability compared to that of a benzyltrimethyl ammonium-based AEM at 80 °C in 1 M NaOD aqueous solution for 30 days. PMID:27216558

  11. Method of forming oriented block copolymer line patterns, block copolymer line patterns formed thereby, and their use to form patterned articles

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Thomas P.; Hong, Sung Woo; Lee, Doug Hyun; Park, Soojin; Xu, Ting

    2015-10-13

    A block copolymer film having a line pattern with a high degree of long-range order is formed by a method that includes forming a block copolymer film on a substrate surface with parallel facets, and annealing the block copolymer film to form an annealed block copolymer film having linear microdomains parallel to the substrate surface and orthogonal to the parallel facets of the substrate. The line-patterned block copolymer films are useful for the fabrication of magnetic storage media, polarizing devices, and arrays of nanowires.

  12. Manipulating Interfaces through Surface Confinement of Poly(glycidyl methacrylate)-block-poly(vinyldimethylazlactone), a Dually Reactive Block Copolymer

    International Nuclear Information System (INIS)

    The assembly of dually reactive, well-defined diblock copolymers incorporating the chemoselective/functional monomer, 4,4-dimethyl-2-vinylazlactone (VDMA) and the surface-reactive monomer glycidyl methacrylate (GMA) is examined to understand how competition between surface attachment and microphase segregation influences interfacial structure. Reaction of the PGMA block with surface hydroxyl groups not only anchors the copolymer to the surface, but limits chain mobility, creating brush-like structures comprising PVDMA blocks, which contain reactive azlactone groups. The block copolymers are spin coated at various solution concentrations and annealed at elevated temperature to optimize film deposition to achieve a molecularly uniform layer. The thickness and structure of the polymer thin films are investigated by ellipsometry, infrared spectroscopy, and neutron reflectometry. The results show that deposition of PGMA-b-PVDMA provides a useful route to control film thickness while preserving azlactone groups that can be further modified with biotin-poly(ethylene glycol)amine to generate designer surfaces. The method described herein offers guidance for creating highly functional surfaces, films, or coatings through the use of dually reactive block copolymers and postpolymerization modification.

  13. Host-guest self-assembly in block copolymer blends.

    Science.gov (United States)

    Park, Woon Ik; Kim, Yongjoo; Jeong, Jae Won; Kim, Kyungho; Yoo, Jung-Keun; Hur, Yoon Hyung; Kim, Jong Min; Thomas, Edwin L; Alexander-Katz, Alfredo; Jung, Yeon Sik

    2013-01-01

    Ultrafine, uniform nanostructures with excellent functionalities can be formed by self-assembly of block copolymer (BCP) thin films. However, extension of their geometric variability is not straightforward due to their limited thin film morphologies. Here, we report that unusual and spontaneous positioning between host and guest BCP microdomains, even in the absence of H-bond linkages, can create hybridized morphologies that cannot be formed from a neat BCP. Our self-consistent field theory (SCFT) simulation results theoretically support that the precise registration of a spherical BCP microdomain (guest, B-b-C) at the center of a perforated lamellar BCP nanostructure (host, A-b-B) can energetically stabilize the blended morphology. As an exemplary application of the hybrid nanotemplate, a nanoring-type Ge2Sb2Te5 (GST) phase-change memory device with an extremely low switching current is demonstrated. These results suggest the possibility of a new pathway to construct more diverse and complex nanostructures using controlled blending of various BCPs. PMID:24217036

  14. Observed frustration in confined block copolymers

    International Nuclear Information System (INIS)

    Symmetric diblock copolymers confined between two solid surfaces were studied by neutron reflectivity. A multilayered morphology with an integral number of layers oriented parallel to the solid interfaces was found in all cases. The period of the confined multilayers deviated from the bulk period in a cyclic manner as a function of the confined film thickness. A first-order transition occurred between the expanded and contracted states of the copolymer chains. The data suggest that the deviation of the period from the bulk value decreases with increasing separation distance

  15. Self-Assembled Asymmetric Block Copolymer Membranes: Bridging the Gap from Ultra- to Nanofiltration

    KAUST Repository

    Yu, Haizhou

    2015-09-21

    The self-assembly of block copolymers is an emerging strategy to produce isoporous ultrafiltration membranes. However, thus far, it has not been possible to bridge the gap from ultra- to nanofiltration and decrease the pore size of self-assembled block copolymer membranes to below 5 nm without post-treatment. It is now reported that the self-assembly of blends of two chemically interacting copolymers can lead to highly porous membranes with pore diameters as small as 1.5 nm. The membrane containing an ultraporous, 60 nm thin separation layer can fully reject solutes with molecular weights of 600 g mol−1 in aqueous solutions with a water flux that is more than one order of magnitude higher than the permeance of commercial nanofiltration membranes. Simulations of the membrane formation process by dissipative particle dynamics (DPD) were used to explain the dramatic observed pore size reduction combined with an increase in water flux.

  16. Self-Assembled Asymmetric Block Copolymer Membranes: Bridging the Gap from Ultra- to Nanofiltration.

    Science.gov (United States)

    Yu, Haizhou; Qiu, Xiaoyan; Moreno, Nicolas; Ma, Zengwei; Calo, Victor Manuel; Nunes, Suzana P; Peinemann, Klaus-Viktor

    2015-11-16

    The self-assembly of block copolymers is an emerging strategy to produce isoporous ultrafiltration membranes. However, thus far, it has not been possible to bridge the gap from ultra- to nanofiltration and decrease the pore size of self-assembled block copolymer membranes to below 5 nm without post-treatment. It is now reported that the self-assembly of blends of two chemically interacting copolymers can lead to highly porous membranes with pore diameters as small as 1.5 nm. The membrane containing an ultraporous, 60 nm thin separation layer can fully reject solutes with molecular weights of 600 g mol(-1) in aqueous solutions with a water flux that is more than one order of magnitude higher than the permeance of commercial nanofiltration membranes. Simulations of the membrane formation process by dissipative particle dynamics (DPD) were used to explain the dramatic observed pore size reduction combined with an increase in water flux. PMID:26388216

  17. Block copolymer/homopolymer dual-layer hollow fiber membranes

    KAUST Repository

    Hilke, Roland

    2014-12-01

    We manufactured the first time block copolymer dual-layer hollow fiber membranes and dual layer flat sheet membranes manufactured by double solution casting and phase inversion in water. The support porous layer was based on polystyrene and the selective layer with isopores was formed by micelle assembly of polystyrene-. b-poly-4-vinyl pyridine. The dual layers had an excellent interfacial adhesion and pore interconnectivity. The dual membranes showed pH response behavior like single layer block copolymer membranes with a low flux for pH values less than 3, a fast increase between pH4 and pH6 and a constant high flux level for pH values above 7. The dry/wet spinning process was optimized to produce dual layer hollow fiber membranes with polystyrene internal support layer and a shell block copolymer selective layer.

  18. Characterization of Lithium Polysulfide Salts in Homopolymers and Block Copolymers

    Science.gov (United States)

    Wang, Dunyang; Wujcik, Kevin; Balsara, Nitash

    Ion-conducting polymers are important for solid-state batteries due to the promise of better safety and the potential to produce higher energy density batteries. Nanostructured block copolymer electrolytes can provide high ionic conductivity and mechanical strength through microphase separation. One of the potential use of block copolymer electrolytes is in lithium-sulfur batteries, a system that has high theoretical energy density wherein the reduction of sulfur leads to the formation of lithium polysulfide intermediates. In this study we investigate the effect of block copolymer morphology on the speciation and transport properties of the polysulfides. The morphology and conductivities of polystyrene-b-poly(ethylene oxide) (SEO) containing lithium polysulfides were studies using small-angle X-ray scattering and ac impedance spectroscopy. UV-vis spectroscopy is being used to determine nature of the polysulfide species in poly(ethylene oxide) and SEO. Department of Energy, Soft Matter Electron Microscopy Program and Battery Materials Research Program.

  19. SANS and SAXS study of block copolymer/homopolymer mixtures

    International Nuclear Information System (INIS)

    The lateral and vertical components of the radius of gyration for a single block copolymer chain and those of a single homopolymer chain in the lamellar microdomain space formed by a mixture of diblock copolymers and homopolymers were investigated by means of small-angle neutron scattering (SANS) and the microdomain structures by small-angle X-ray scattering (SAXS). The homopolymers whose molecular weights are much smaller than that of the corresponding chains of the block copolymers were used so that the homopolymers were uniformly solubilized in the corresponding microdomains. The SANS result suggests that the homopolymer chains in the microdomain space as well as the block copolymer chains are more compressed in the direction parallel to the interface and more stretched in the direction perpendicular to the interface than the corresponding unperturbed polymer chains with the same molecular weight. On increasing the volume fraction of the homopolymers the thickness of the lamellar microdomains increases. The block copolymer chains were found to undergo an isochoric affine deformation on addition of the homopolymers or with the change of the thickness of the lamellar microdomains. (orig.)

  20. Design of block copolymer membranes using segregation strength trend lines

    KAUST Repository

    Sutisna, Burhannudin

    2016-05-18

    Block copolymer self-assembly and non-solvent induced phase separation are now being combined to fabricate membranes with narrow pore size distribution and high porosity. The method has the potential to be used with a broad range of tailor-made block copolymers to control functionality and selectivity for specific separations. However, the extension of this process to any new copolymer is challenging and time consuming, due to the complex interplay of influencing parameters, such as solvent composition, polymer molecular weights, casting solution concentration, and evaporation time. We propose here an effective method for designing new block copolymer membranes. The method consists of predetermining a trend line for the preparation of isoporous membranes, obtained by computing solvent properties, interactions and copolymer block sizes for a set of successful systems and using it as a guide to select the preparation conditions for new membranes. We applied the method to membranes based on poly(styrene-b-ethylene oxide) diblocks and extended it to newly synthesized poly(styrene-b-2-vinyl pyridine-b-ethylene oxide) (PS-b-P2VP-b-PEO) terpolymers. The trend line method can be generally applied to other new systems and is expected to dramatically shorten the path of isoporous membrane manufacture. The PS-b-P2VP-b-PEO membrane formation was investigated by in situ Grazing Incident Small Angle X-ray Scattering (GISAXS), which revealed a hexagonal micelle order with domain spacing clearly correlated to the membrane interpore distances.

  1. Controlling block copolymer phase behavior using ionic surfactant

    Science.gov (United States)

    Ray, D.; Aswal, V. K.

    2016-05-01

    The phase behavior of poly(ethylene oxide)-poly(propylene oxide-poly(ethylene oxide) PEO-PPO-PEO triblock copolymer [P85 (EO26PO39EO26)] in presence of anionic surfactant sodium dodecyl sulfate (SDS) in aqueous solution as a function of temperature has been studied using dynamic light scattering (DLS) and small-angle neutron scattering (SANS). The measurements have been carried out for fixed concentrations (1 wt%) of block copolymer and surfactants. Each of the individual components (block copolymer and surfactant) and the nanoparticle-surfactant mixed system have been examined at varying temperature. The block copolymer P85 forms spherical micelles at room temperature whereas shows sphere-to-rod like micelle transition at higher temperatures. On the other hand, SDS surfactant forms ellipsoidal micelles over a wide temperature range. Interestingly, it is found that phase behavior of mixed micellar system (P85 + SDS) as a function of temperature is drastically different from that of P85, giving the control over the temperature-dependent phase behavior of block copolymers.

  2. Tuning of Block Copolymer Membrane Morphology through Water Induced Phase Inversion Technique

    KAUST Repository

    Madhavan, Poornima

    2016-06-01

    Isoporous membranes are attractive for the regulation and detection of transport at the molecular level. A well-defined asymmetric membranes from diblock copolymers with an ordered nanoporous membrane morphologies were fabricated by the combination of block copolymer self-assembly and non-solvent-induced phase separation (NIPS) technique. This is a straightforward and fast one step procedure to develop integrally anisotropic (“asymmetric”) membranes having isoporous top selective layer. Membranes prepared via this method exhibit an anisotropic cross section with a thin separation layer supported from underneath a macroporous support. These membrane poses cylindrical pore structure with ordered nanopores across the entire membrane surfaces with pore size in the range from 20 to 40 nm. Tuning the pore morphology of the block copolymer membranes before and after fabrication are of great interest. In this thesis, we first investigated the pore morphology tuning of asymmetric block copolymer membrane by complexing with small organic molecules. We found that the occurrence of hydrogen-bond formation between PS-b-P4VP block copolymer and –OH/ –COOH functionalized organic molecules significantly tunes the pore morphology of asymmetric nanoporous membranes. In addition, we studied the complexation behavior of ionic liquids with PS-b-P4VP block copolymer in solutions and investigated their effect on final membrane morphology during the non-solvent induced phase separation process. We found that non-protic ionic liquids facilitate the formation of hexagonal nanoporous block copolymer structure, while protic ionic liquids led to a lamella-structured membrane. Secondly, we demonstrated the catalytic activity of the gold nanoparticle-enhanced hollow fiber membranes by the reduction of nitrophenol. Also, we systematically investigated the pore morphology of isoporous PS-b-P4VP using 3D imaging technique. Thirdly, we developed well-distributed silver nanoparticles on the

  3. Interfacial Phenomena of Solvent-diluted Block Copolymers

    OpenAIRE

    Cohen, Shai; Andelman, David

    2013-01-01

    A phenomenological mean-field theory is used to investigate the properties of solvent-diluted di-block copolymers (BCP), in which the two BCP components (A and B) form a variety of phases that are diluted by a solvent (S). Using this approach, we model mixtures of di-block copolymers and a solvent and obtained the corresponding critical behavior. In the low solvent limit, we find how the critical point depends on the solvent density. Due to the non-linear nature of the coupling between the A/...

  4. Nanofabrication of Block Copolymers of PDMS/Polyamide having Trichlorogermyl Pendant Using LbL Technique

    International Nuclear Information System (INIS)

    Block copolymers (AB)x type of aminopropyl-terminated poly(dimethylsiloxane) (NH2- PDMS) and polyamides trichlorogermyl pendant group were prepared by a solution phase one pot polycondensation method. The prepared block copolymers were assembled with polyethylene-alt- (maleic) anhydride (PEMA) as multilayered thin film assembly through covalently linked Layer by Layer (LbL) technique using dipping method. The prepared thin films had thickness in the range of 15 to 20 nm as measured on an ellipsometers. In the systems where quartz was used as substrate, film growth after each deposition was monitored through UV-Vis spectrophotometer, which substantiated the multilayer film build-up. Atomic Force Microscopic (AFM) images showed homogeneous and robust film, which were strong enough to endure the force of 400 nN. As the block copolymers are thermally stable and have the capacity to absorb water, so their prepared robust ultra-thin films can show potential of thermally resistant nano thin films, protective hydrophilic coatings in addition to separation membranes. (author)

  5. Block and Graft Copolymers of Polyhydroxyalkanoates

    Science.gov (United States)

    Marchessault, Robert H.; Ravenelle, François; Kawada, Jumpei

    2004-03-01

    Polyhydroxyalkanoates (PHAs) were modified for diblock copolymer and graft polymer by catalyzed transesterification in the melt and by chemical synthesis to extend the side chains of the PHAs, and the polymers were studied by transmission electron microscopy (TEM) X-ray diffraction, thermal analysis and nuclear magnetic resonance (NMR). Catalyzed transesterification in the melt is used to produce diblock copolymers of poly[3-hydroxybutyrate] (PHB) and monomethoxy poly[ethylene glycol] (mPEG) in a one-step process. The resulting diblock copolymers are amphiphilic and self-assemble into sterically stabilized colloidal suspensions of PHB crystalline lamellae. Graft polymer was synthesized in a two-step chemical synthesis from biosynthesized poly[3-hydroxyoctanoate-co-3-hydroxyundecenoate] (PHOU) containing ca. 25 mol chains. 11-mercaptoundecanoic acid reacts with the side chain alkenes of PHOU by the radical addition creating thioether linkage with terminal carboxyl functionalities. The latter groups were subsequently transformed into the amide or ester linkage by tridecylamine or octadecanol, respectively, producing new graft polymers. The polymers have different physical properties than poly[3-hydroxyoctanoate] (PHO) which is the main component of the PHOU, such as non-stickiness and higher thermal stability. The combination of biosynthesis and chemical synthesis produces a hybrid thermoplastic elastomer with partial biodegradability.

  6. Chain exchange kinetics of block copolymer micelles in ionic liquids

    Science.gov (United States)

    Ma, Yuanchi; Lodge, Timothy

    The chain exchange kinetics of block copolymer micelles has been studied using time-resolved small-angle neutron scattering (TR-SANS), a key tool in determining the average micelle composition in contrast-matched solvents. In this work, PMMA-block-PnBMA was selected as the model block copolymer, which has a LCST behavior in the common ionic liquids, [EMIM][TFSI] and [BMIM][TFSI]. We examined the chain exchange kinetics of three PMMA-block-PnBMA copolymers, with identical PMMA block length (MPMMA = 25000) and different PnBMA block lengths (MPnBMA = 24000, 35000 and 53000); the Flory-Huggins interaction parameter (χ) between the core (PnBMA) and the solvent were varied by mixing [EMIM][TFSI] and [BMIM][TFSI] in different ratios. We found that the relaxation of the initial segregation of h- and d- micelles followed the same form with the time as previously developed by our group. Assuming that single chain expulsion is the rate limiting step, the thermal barrier was found to depend linearly on the core block length (Ncore) . Furthermore, the effect of χ on the chain exchange kinetics will also be discussed.

  7. Segmented block copolymers with polyesteramide blocks of uniform length: synthesis

    NARCIS (Netherlands)

    Gaymans, R.J.; Haan, de J.L.

    1993-01-01

    Segmented copolymers were synthesized from poly(tetramethylene oxide) with hydroxy end-groups or aliphatic diols and a short-chain diester diamide with a uniform length. The diester diamide (N,N'-bis(p-carbomethoxybenzoyl)butanediamine) (Tm = 257°C) used is made from butanediamine and an excess of d

  8. Stability of ordered phases in block copolymer melts and solutions

    Indian Academy of Sciences (India)

    Kell Mortensen

    2008-11-01

    Block copolymer melts and solutions assemble into nanosized objects that order into a variety of phases, depending on molecular parameters and mutual interactions. Beyond the classical phases of lamella ordered sheets, hexagonally ordered cylinders and cubic ordered spheres, the complex bicontinuous gyroid phase and the modulated lamellar phase are observed near the phase boundaries. The stability of these phases has been discussed on the basis of theoretical calculations. Here, we will discuss new experimental results showing that the given ordered phase depends critically on both molecular purity and mechanical treatment of the sample. While a variety of block copolymer micellar systems have been shown to undergo the liquid-to-bcc-to-fcc phase sequence upon varying micellar parameters (or temperature), we find for a purified system a different sequence, namely liquid-to-fcc-to-bcc [1]. The latter sequence is by the way the one predicted for pure block copolymer melts. External fields like shear or stress may also affect the ordered phase. Applying well-controlled large-amplitude oscillatory shear can be used to effectively control the texture of soft materials in the ordered states. As an example, we present results on a body-centred-cubic phase of a block copolymer system, showing how a given texture can be controlled with the application of specific shear rate and shear amplitude [2,3]. Shear may however also affect the thermodynamic ground state, causing shear-induced ordering and disordering (melting), and shear-induced order–order transitions. We will present data showing that the gyroid state of diblock copolymer melts is unstable when exposed to large amplitude/frequency shear, transforming into the hexagonal cylinder phase [4]. The transformation is completely reversible. With the rather slow kinetics in the transformation of copolymer systems, it is possible in detail to follow the complex transformation process, where we find transient ordered

  9. Low molecular weight block copolymers as plasticizers for polystyrene

    DEFF Research Database (Denmark)

    Hansen, Kristoffer Karsten; Nielsen, Charlotte Juel; Hvilsted, Søren

    2005-01-01

    Polystyrene-b-alkyl, polystyrene-b-polybutadiene-b-polystyrene, and polystyrene-b-poly(propylene glycol)monotridecyl ether were synthesized using macro initiators and atom transfer radical polymerization or by esterifications of homopolymers. The aim was a maximum molecular weight of 4 kg/mol and...... minimum polystyrene content of 50 w/w%, which by us is predicted as the limits for solubility of polystyrene-b-alkyl in polystyrene. DSC showed polystyrene was plasticized, as seen by a reduction in glass transition temperature, by block copolymers consisting of a polystyrene block with molecular weight...... of approximately 1 kg/mol and an alkyl block with a molecular weight of approximately of 0.3 kg/mol. The efficiency of the block copolymers as plasticizers increases with decreasing molecular weight and polystyrene content. In addition, polystyrene-b-alkyl is found to be an efficient plasticizer also...

  10. Complexes of block copolymers in solution: tree approximation

    NARCIS (Netherlands)

    Geurts, Bernard J.; Damme, van Ruud

    1989-01-01

    We determine the statistical properties of block copolymer complexes in solution. These complexes are assumed to have the topological structure of (i) a tree or of (ii) a line-dressed tree. In case the structure is that of a tree, the system is shown to undergo a gelation transition at sufficiently

  11. Fast assembly of ordered block copolymer nanostructures through microwave annealing.

    Science.gov (United States)

    Zhang, Xiaojiang; Harris, Kenneth D; Wu, Nathanael L Y; Murphy, Jeffrey N; Buriak, Jillian M

    2010-11-23

    Block copolymer self-assembly is an innovative technology capable of patterning technologically relevant substrates with nanoscale precision for a range of applications from integrated circuit fabrication to tissue interfacing, for example. In this article, we demonstrate a microwave-based method of rapidly inducing order in block copolymer structures. The technique involves the usage of a commercial microwave reactor to anneal block copolymer films in the presence of appropriate solvents, and we explore the effect of various parameters over the polymer assembly speed and defect density. The approach is applied to the commonly used poly(styrene)-b-poly(methyl methacrylate) (PS-b-PMMA) and poly(styrene)-b-poly(2-vinylpyridine) (PS-b-P2VP) families of block copolymers, and it is found that the substrate resistivity, solvent environment, and anneal temperature all critically influence the self-assembly process. For selected systems, highly ordered patterns were achieved in less than 3 min. In addition, we establish the compatibility of the technique with directed assembly by graphoepitaxy. PMID:20964379

  12. SANS study of nanoparticles based on block copolymer micelles

    Czech Academy of Sciences Publication Activity Database

    Pleštil, Josef; Pospíšil, Herman; Kuklin, A. I.

    Dubna: Joint Institute for Nuclear Research, Lomonosov Moscow State University, 2005. s. 22. ISBN 5-9530-0086-3. [Workshop on Investigations at the IBR-2 Pulsed Reactor /4./. 15.6.2005-18.6.2005, Dubna] R&D Projects: GA ČR GA203/03/0600 Keywords : SANS * block copolymer micelles * nanoparticles Subject RIV: CD - Macromolecular Chemistry

  13. Spectroscopic study of thermoresponsive block copolymers in aqueous solution

    Czech Academy of Sciences Publication Activity Database

    Spěváček, Jiří; Konefal, Rafal; Dybal, Jiří; Čadová, Eva

    Amsterdam: Elsevier, 2015. P116. [International Colloids Conference /5./. 21.06.2015-24.06.2015, Amsterdam] R&D Projects: GA ČR(CZ) GA15-13853S Institutional support: RVO:61389013 Keywords : thermoresponsive polymer * block copolymer * poly(N-isopropylacrylamide) Subject RIV: CD - Macromolecular Chemistry

  14. Silicon crystallization in nanodot arrays organized by block copolymer lithography

    Energy Technology Data Exchange (ETDEWEB)

    Perego, Michele, E-mail: michele.perego@mdm.imm.cnr.it; Andreozzi, Andrea; Seguini, Gabriele [IMM-CNR, Laboratorio MDM (Italy); Schamm-Chardon, Sylvie; Castro, Celia; BenAssayag, Gerard [Université de Toulouse, nMat Group, CEMES-CNRS (France)

    2014-12-15

    Asymmetric polystyrene-b-polymethylmethacrylate (PS-b-PMMA) block copolymers are used to fabricate nanoporous PS templates with different pore diameter depending on the specific substrate neutralization protocol. The resulting polymeric templates are used as masks for the subsequent deposition of a thin (h = 5 nm) amorphous Si layer by electron beam evaporation. After removal of the polymeric film and of the silicon excess, well-defined hexagonally packed amorphous Si nanodots are formed on the substrate. Their average diameter (d < 20 nm), density (1.2 × 10{sup 11} cm{sup −2}), and lateral distribution closely mimic the original nanoporous template. Upon capping with SiO{sub 2} and high temperature annealing (1050 °C, N{sub 2}), each amorphous Si nanodot rearranges in agglomerates of Si nanocrystals (d < 4 nm). The average diameter and shape of these Si nanocrystals strongly depend on the size of the initial Si nanodot.

  15. Silicon crystallization in nanodot arrays organized by block copolymer lithography

    International Nuclear Information System (INIS)

    Asymmetric polystyrene-b-polymethylmethacrylate (PS-b-PMMA) block copolymers are used to fabricate nanoporous PS templates with different pore diameter depending on the specific substrate neutralization protocol. The resulting polymeric templates are used as masks for the subsequent deposition of a thin (h = 5 nm) amorphous Si layer by electron beam evaporation. After removal of the polymeric film and of the silicon excess, well-defined hexagonally packed amorphous Si nanodots are formed on the substrate. Their average diameter (d < 20 nm), density (1.2 × 1011 cm−2), and lateral distribution closely mimic the original nanoporous template. Upon capping with SiO2 and high temperature annealing (1050 °C, N2), each amorphous Si nanodot rearranges in agglomerates of Si nanocrystals (d < 4 nm). The average diameter and shape of these Si nanocrystals strongly depend on the size of the initial Si nanodot

  16. Novel multiarm star block copolymer ionomers as proton conductive membranes

    OpenAIRE

    Demirel, Adem Levent; Erdoğan, Tuba; Bilir, Çiğdem; Ünveren, Elif; Tunca, Ümit

    2014-01-01

    A series of well-defined novel multiarm star block copolymer ionomers with an average of 6, 11 and 15 arms, sulfonated polystyrene-block-poly(2,2,3,3,3-pentafluoropropyl methacrylate) (SPS-b-PFPMA), were prepared via a combination of atom transfer radical polymerization (ATRP), Diels–Alder click reaction and postsulfonation reaction. First, multiarm star polymer with anthracene functionality as reactive periphery groups was prepared by a cross-linking reaction of divinyl benzene using ?-anthr...

  17. Functional Block Copolymers as Compatibilizers for Nanoclays in Polypropylene Nanocomposites

    DEFF Research Database (Denmark)

    Jankova Atanasova, Katja; Daugaard, Anders Egede; Stribeck, Norbert;

    With the aim of creating tough nanocomposits (NC) [1] based on polypropylene (PP) and nanoclay (NCl) in the framework of the 7th EU program NANOTOUGH we have designed amphiphilic block copolymers utilizing Atom Transfer Radical Polymerization (ATRP) [2]. They consist of a hydrophobic block of...... PP (by its crystallites) is replaced by alien-reinforcement (of the MMT). Furthermore, the results from the impact strength and cyclic test of the prepared PP nanocomposites [3] are promicing....

  18. Theoretical study on tailoring symmetric and asymmetric thin films of diblock copolymers

    International Nuclear Information System (INIS)

    We used density functional theory (DFT) to investigate the formation of symmetric and asymmetric thin film of diblock copolymer melts by tuning the size of the slit confinement. In this work, the DFT contains a modified fundamental measure theory for the excluded volume effect and the first-order thermodynamic perturbation theory for the chain connectivity as well as the mean-field approximation for van der Waals attraction. For the symmetric A8B8 linear copolymers, it is observed that with the increase of the width of the slit, morphologies of copolymer in the slits undergo an evolution of 'non-layered structure → ABA → ABAB → BABAB → disordered structure', while the morphologies of asymmetric copolymer with the increase of the width of the slit exhibit a process of 'ABA → ABAB → ABABA → ABABAB lamellar structure' in all the cases studied. It suggests that the ratio of two blocks of a copolymer plays an important role on the structure of copolymer film. By adjusting the ratio of two blocks, some copolymer films with novel morphologies, including asymmetric ABAB lamellar structure, can be tailored. Furthermore, it is found that the bonding orientation distribution introduced into the DFT can act as a criterion to identify the disordered and ordered states of copolymers

  19. Novel lift-off technique for Transmission Electron Microscopy imaging of block copolymer films

    International Nuclear Information System (INIS)

    We have developed a simple technique to allow for the lift-off and subsequent transfer of poly(styrene-block-ethylene glycol) films to Transmission Electron Microscopy (TEM) grids. The block copolymer is spin coated onto carbon coated mica and annealed. After the thin film is produced it can easily be floated onto water and picked up by a TEM grid. This method offers better control over film processing than dip coating the TEM grid and is also a significant improvement over methods using etchants such as hydrofluoric acid. - Highlights: • We have developed a simple method to lift block copolymer films to TEM grids. • Polymer films prepared on carbon coated mica are easily floated on water. • The new method circumvents the use of harsh chemicals

  20. Polystyrene-b-polyethylene oxide block copolymer membranes, methods of making, and methods of use

    KAUST Repository

    Peinemann, Klaus-Viktor

    2015-04-16

    Embodiments of the present disclosure provide for polystyrene-b-polyethylene oxide (PS-b-PEO) block copolymer nanoporous membranes, methods of making a PS-b-PEO block copolymer nanoporous membrane, methods of using PS-b-PEO block copolymer nanoporous membranes, and the like.

  1. Nanostructured Amphiphilic Star-Hyperbranched Block Copolymers for Drug Delivery.

    Science.gov (United States)

    Seleci, Muharrem; Seleci, Didem Ag; Ciftci, Mustafa; Demirkol, Dilek Odaci; Stahl, Frank; Timur, Suna; Scheper, Thomas; Yagci, Yusuf

    2015-04-21

    A robust drug delivery system based on nanosized amphiphilic star-hyperbranched block copolymer, namely, poly(methyl methacrylate-block-poly(hydroxylethyl methacrylate) (PMMA-b-PHEMA) is described. PMMA-b-PHEMA was prepared by sequential visible light induced self-condensing vinyl polymerization (SCVP) and conventional vinyl polymerization. All of the synthesis and characterization details of the conjugates are reported. To accomplish tumor cell targeting property, initially cell-targeting (arginylglycylaspactic acid; RGD) and penetrating peptides (Cys-TAT) were binding to each other via the well-known EDC/NHS chemistry. Then, the resulting peptide was further incorporated to the surface of the amphiphilic hyperbranched copolymer via a coupling reaction between the thiol (-SH) group of the peptide and the hydroxyl group of copolymer by using N-(p-maleinimidophenyl) isocyanate as a heterolinker. The drug release property and targeting effect of the anticancer drug (doxorobucin; DOX) loaded nanostructures to two different cell lines were evaluated in vitro. U87 and MCF-7 were chosen as integrin αvβ3 receptor positive and negative cells for the comparison of the targeting efficiency, respectively. The data showed that drug-loaded copolymers exhibited enhanced cell inhibition toward U87 cells in compared to MCF-7 cells because targeting increased the cytotoxicity of drug-loaded copolymers against integrin αvβ3 receptor expressing tumor cells. PMID:25816726

  2. Structure-property relationships in multilayered polymeric system and olefinic block copolymers

    Science.gov (United States)

    Khariwala, Devang

    Chapter 1. The effect of tie-layer thickness on delamination behavior of polypropylene/tie-layer/Nylon-6 multilayers is examined in this study. Various maleated polypropylene resins were compared for their effectiveness as tie-layers. Delamination failure occurred cohesively in all the multilayer systems. Two adhesion regimes were defined based on the change in slope of the linear relationship between the delamination toughness and the tie-layer thickness. The measured delamination toughness of the various tie-layers was quantitatively correlated to the damage zone length formed at the crack tip. In addition, the effect of tie-layer thickness on the multilayer tensile properties was correlated with the delamination behavior. The fracture strain of the multilayers decreased with decreasing tie-layer thickness. Examination of the prefracture damage mechanism of stretched multilayers revealed good correlation with the delamination toughness of the tie-layers. In thick tie-layers (>2microm) the delamination toughness of the tie-layers was large enough to prevent delamination of multilayers when they were stretched. In the thin tie-layers (block copolymers with properties typical of thermoplastic elastomers. The block copolymers synthesized by chain shuttling technology consist of crystallizable ethylene-octene blocks with low comonomer content and high melting temperature (hard blocks), alternating with amorphous ethylene-octene blocks with high comonomer content and low glass transition temperature (soft blocks). This study describes the material science of these unique polymers as characterized by thermal analysis, X-ray diffraction, microscopy, and tensile deformation. The crystallizable blocks are long enough to form well-organized lamellar crystals with the orthorhombic unit cell and high melting temperature. The lamellae are organized into space-filling spherulites in all compositions even in copolymers with only 18 wt% hard block. The morphology is consistent

  3. Directed Self-assembly of Block Copolymer with Sub-15 nm Domain Spacing Using Nanoimprinted Photoresist Templates

    Science.gov (United States)

    Sun, Zhiwei; Chen, Zhenbin; Zhang, Wenxu; Coughlin, E. Bryan; Xiao, Shuaigang; Russell, Thomas

    There has been increasing interest in preparing block copolymer thin films with ultra-small domain spacings for use as etching masks for ultra-high resolution nanolithography. One method to prepare block copolymer materials with small feature sizes is salt doping, increasing the Flory-Huggins interaction and allowing microphase separation to be maintained at lower molecular weights. Lamellae-forming P2VP- b-PS- b-P2VP block copolymer with various molecular weight was synthesized using RAFT polymerization with a dual functional chain transfer agent. Copper (II) Chloride or Gold (III) chloride was found to be selectively associated with P2VP block and increase the unfavorable interactions between PS and P2VP blocks, driving the disordered block copolymer into the ordered state. A 14 nm lamellar spacing of P2VP- b-PS- b-P2VP thin film was prepared using copper (II) Chloride doping after acetone vapor annealing on neutral brushes. Metallic nano-wire arrays were prepared after selective infiltration of platinum salt into the P2VP domain and oxygen plasma treatment. The directed self-assembly of salt doped P2VP- b-PS- b-P2VP triblock copolymer having long-rang lateral order on nanoimprinted photoresist templates with shallow trenches was also studied.

  4. Stereo block copolymers of L- and D-lactides

    OpenAIRE

    Yui, Nobuhiko; Pieter J. Dijkstra; Feijen, Jan

    1990-01-01

    Sequential diblock copolymers composed of L- and D-lactic acid residues were synthesized through a living ring-opening polymerization of L- and D-lactide initiated by aluminium tris(2-propanolate). The composition of the block copolymers was varied by changing the reaction conditions and monomer over initiator ratio and confirmed by 1H NMR analysis, molecular weight determination and optical rotation measurements. Molecular weights ranged from 1,3 to 2,0 · 104 with 1,2 < Mw/Mn < 1,4. Stereoco...

  5. Polymers and block copolymers of fluorostyrenes by ATRP

    DEFF Research Database (Denmark)

    Hvilsted, Søren; Borkar, Sachin; Abildgaard, Lillian; Georgieva, V.; Siesler, H.W.; Jankova, Katja Atanassova

    2002-01-01

    Fully or partly fluorinated polymers have many desirable and intriguing properties. In the framework of a larger program on design and control of new functional block copolymers we recently employed the Atom Transfer Radical Polymerization (ATRP) protocol on 2,3,4,5,6-pentafluorostyrene (FS). We...... materials based on 2,3,5,6-tetrafiuoro-4-methoxy-styrene (TFMS). TFMS homopolymers as well as diblock copolymers with FS are produced by ATRP. Both types of novel polymers were subsequently demethylated and different side chains introduced on the resulting hydroxy sites....

  6. Block copolymer-nanoparticle hybrid self-assembly

    KAUST Repository

    Hoheisel, Tobias N.

    2015-01-01

    © 2014 Published by Elsevier Ltd. Polymer-inorganic hybrid materials provide exciting opportunities as they may display favorable properties from both constituents that are desired in applications including catalysis and energy conversion and storage. For the preparation of hybrid materials with well-defined morphologies, block copolymer-directed nanoparticle hybrids present a particularly promising approach. As will be described in this review, once the fundamental characteristics for successful nanostructure formation at or close to the thermodynamic equilibrium of these nanocomposites are identified, the approach can be generalized to various materials classes. In addition to the discussion of recent materials developments based on the use of AB diblock copolymers as well as ABC triblock terpolymers, this review will therefore emphasize progress in the fundamental understanding of the underlying formation mechanisms of such hybrid materials. To this end, critical experiments for, as well as theoretical progress in the description of these nanostructured block copolymer-based hybrid materials will be discussed. Rather than providing a comprehensive overview, the review will emphasize work by the Wiesner group at Cornell University, US, on block copolymer-directed nanoparticle assemblies as well as their use in first potential application areas. The results provide powerful design criteria for wet-chemical synthesis methodologies for the generation of functional nanomaterials for applications ranging from microelectronics to catalysis to energy conversion and storage.

  7. Design and Application of Nanoscale Actuators Using Block-Copolymers

    Directory of Open Access Journals (Sweden)

    Paul D. Topham

    2010-10-01

    Full Text Available Block copolymers are versatile designer macromolecules where a “bottom-up” approach can be used to create tailored materials with unique properties. These simple building blocks allow us to create actuators that convert energy from a variety of sources (such as chemical, electrical and heat into mechanical energy. In this review we will discuss the advantages and potential pitfalls of using block copolymers to create actuators, putting emphasis on the ways in which these materials can be synthesised and processed. Particular attention will be given to the theoretical background of microphase separation and how the phase diagram can be used during the design process of actuators. Different types of actuation will be discussed throughout.

  8. Formation and Characterization of Anisotropic Block Copolymer Gels

    Science.gov (United States)

    Liaw, Chya Yan; Joester, Derk; Burghardt, Wesley; Shull, Kenneth

    2012-02-01

    Cylindrical micelles formed from block copolymer solutions closely mimic biological fibers that are presumed to guide mineral formation during biosynthesis of hard tissues like bone. The goal of our work is to use acrylic block copolymers as oriented templates for studying mineral formation reactions in model systems where the structure of the underlying template is well characterized and reproducible. Self-consistent mean field theory is first applied to investigate the thermodynamically stable micellar morphologies as a function of temperature and block copolymer composition. Small-angle x-ray scattering, optical birefringence and shear rheometry are used to study the morphology development during thermal processing. Initial experiments are based on a thermally-reversible alcohol-soluble system that can be converted to an aqueous gel by hydrolysis of a poly(t-butyl methacrylate) block to a poly(methacrylic acid) block. Aligned cylindrical domains are formed in the alcohol-based system when shear is applied in an appropriate temperature regime, which is below the critical micelle temperature but above the temperature at which the relaxation time of the gels becomes too large. Processing strategies for producing the desired cylindrical morphologies are being developed that account for both thermodynamic and kinetic effects.

  9. Gas Permeation through Polystyrene-Poly(ethylene oxide) Block Copolymers

    Science.gov (United States)

    Hallinan, Daniel, Jr.; Minelli, Matteo; Giacinti-Baschetti, Marco; Balsara, Nitash

    2013-03-01

    Lithium air batteries are a potential technology for affordable energy storage. They consist of a lithium metal anode and a porous air cathode separated by a solid polymer electrolyte membrane, such as PEO/LiTFSI (PEO = poly(ethylene oxide), LiTFSI = lithium bis-trifluoromethane sulfonimide). For extended operation of such a battery, the polymer electrolyte must conduct lithium ions while blocking electrons and gases present in air. In order to maintain a pressure difference the membrane must be mechanically robust, which can be achieved by incorporating the PEO into a block copolymer with a glassy block such as PS (PS = polystyrene). To protect the lithium electrode, the membrane must have low permeability to gases in air such as CO2, N2, and O2. We have therefore studied the permeation of pure gases through a PS-PEO block copolymer. A high molecular weight, symmetric block copolymer with a lamellar morphology was used to cast free-standing membranes. Gas permeability was measured through these membranes with a standard, pressure-based technique. A model was developed to account for transport through the polymer membrane consisting of semi-crystalline PEO lamellae and amorphous PS lamellae. PEO crystallinity was extracted from the permeation model and compares well with values from differential scanning calorimetry measurements.

  10. Synthesis and interactions with blood of polyetherurethaneurea/polypeptide block copolymers.

    Science.gov (United States)

    Ito, Y; Miyashita, K; Kashiwagi, T; Imanishi, Y

    1993-01-01

    Polyurethane/polypeptide block copolymers were synthesized. Infrared spectroscopy and differential scanning calorimetry revealed that in the block copolymers both segments undergo phase-mixing, while in polyurethane/polypeptide blend both components undergo phase-separation. Contact angle measurement showed that in the block copolymers polyurethane segments tended to appear on the membrane surface, whereas in polyurethane/polypeptide blend polypeptide components appeared on the membrane surface. In vitro nonthrombogenicity of the block copolymers was similar to that of homopolymers or polymer blends, though adhesion and deformation of platelets were suppressed on the block copolymer membranes. PMID:8260582

  11. Heat Capacity of Spider Silk-like Block Copolymers

    OpenAIRE

    Huang, Wenwen; Krishnaji, Sreevidhya; Hu, Xiao; Kaplan, David; Cebe, Peggy

    2011-01-01

    We synthesized and characterized a new family of di-block copolymers based on the amino acid sequences of Nephila clavipes major ampulate dragline spider silk, having the form HABn and HBAn (n=1–3), comprising an alanine-rich hydrophobic block, A, a glycine-rich hydrophilic block, B, and a histidine tag, H. The reversing heat capacities, Cp(T), for temperatures below and above the glass transition, Tg, were measured by temperature modulated differential scanning calorimetry. For the solid sta...

  12. Self-assembly of Block and Graft Copolymers in Aerosol Nanoparticles

    OpenAIRE

    Rahikkala, Antti

    2015-01-01

    This study examined how to control the self-assembly of block and graft copolymers during the aerosol process, which produces nanoparticles with phase-separated inner structure and phase dimensions ranging from 3 nm to 30 nm. The nanoparticles were also studied for the possibility of their use as a drug carriers. Block copolymers consist of two or more chemically different polymer blocks covalently bound together. In graft copolymers molecules are bound as side-chains to the copolymer backbon...

  13. Inner Stucture of Thin Films of Lamellar Poly(styrene-b-butadiene) Diblock Copolymers as revealed by Grazing-Incidence Small-Angle Scattering

    DEFF Research Database (Denmark)

    Busch, Peter; Posselt, Dorthe; Smilgies, Detlef-Matthias;

    2007-01-01

    The lamellar orientation in supported, thin films of poly(styrene-b-butadiene) (P(S-b-B)) depends on block copolymer molar mass. We have studied films from nine block copolymer samples with molar masses between 13.9 and 183 kg/mol using grazing-incidence small-angle X-ray scattering (GISAXS) and ...

  14. Adsorption of polyelectrolytes and charged block copolymers on oxides. Consequences for colloidal stability.

    OpenAIRE

    Hoogeveen, N.G.

    1996-01-01

    The aim of the study described in this thesis was to examine the adsorption properties of polyelectrolytes and charged block copolymers on oxides, and the effect of these polymers on the colloidal stability of oxidic dispersions. For this purpose the interaction of some well-characterised polyelectrolytes and block copolymers with oxidic substrates has been systematically studied. A set of block copolymers with one charged block and one neutral water-soluble block had to be synthesised becaus...

  15. Wetting films stabilized by block-copolymers

    NARCIS (Netherlands)

    Eliseeva, O.V.

    2006-01-01

    Thin aqueous films formed on a solid surface play an important role in adhesion, spreading, and colloidal stability. These phenomena are all relevant for paint systems. Measuring surface forces in these films is an experimental challenge, and over the years several techniques have been developed to

  16. Structural and Luminescence Properties of Lu2O3:Eu3+ F127 Tri-Block Copolymer Modified Thin Films Prepared by Sol-Gel Method

    OpenAIRE

    María Luz Carrera Jota; Dulce Yolotzin Medina Velazquez; Joel Moreno Palmerin; Antonieta García Murillo; Felipe de Jesús Carrillo Romo; Margarita García Hernández; Angel de Jesus Morales Ramírez

    2013-01-01

    Lu2O3:Eu3+ transparent, high density, and optical quality thin films were prepared using the sol-gel dip-coating technique, starting with lutetium and europium nitrates as precursors and followed by hydrolysis in an ethanol-ethylene glycol solution. Acetic acid and acetylacetonate were incorporated in order to adjust pH and as a sol stabilizer. In order to increment the thickness of the films and orient the structure, F127 Pluronic acid was incorporated during the sol formation. Structural, m...

  17. Self-assemblies of magnetic nanoparticles and di-block copolymers: Magnetic micelles and vesicles

    International Nuclear Information System (INIS)

    Magnetic nanocomposites are obtained by the self-assembly in water of polypeptide-based di-block copolymers polybutadiene-b-poly(glutamic acid) combined with hydrophobic γ-Fe2O3 nanoparticles. These hybrid supramolecular objects are either-(3D) spherical micelles filled with a hydrophobic ferrofluid at a concentration as high as 45 vol% or-hollow vesicles with a (2D) magnetic membrane. In this last case, the organic amphiphile copolymers are able to confine the hydrophobic nanoparticles within the thin layer of polybutadiene blocks. We probe these objects by atomic force microscopy, by small-angle neutron scattering (SANS) and by light scattering. Furthermore, anisotropic SANS data bring the experimental evidence of the capability to modify the shape of the mineralized membranes in response to a magnetic field intensity as low as 290 G

  18. Biocompatibility of epoxidized styrene-butadiene-styrene block copolymer membrane

    International Nuclear Information System (INIS)

    Styrene-butadiene-styrene block copolymer (SBS) membrane was prepared by solution casting method and then was epoxidized with peroxyformic acid generated in situ to yield the epoxidized styrene-butadiene-styrene block copolymer membrane (ESBS). The structure and properties of ESBS were characterized with infrared spectroscopy, Universal Testing Machine, differential scanning calorimetry (DSC), and thermogravimetry analysis (TGA). The performances of contact angle, water content, protein adsorption, and water vapor transmission rate on ESBS membrane were determined. After epoxidation, the hydrophilicity of the membrane increased. The water vapor transmission rate of ESBS membrane is similar to human skin. The biocompatibility of ESBS membrane was evaluated with the cell culture of fibroblasts on the membrane. It revealed that the cells not only remained viable but also proliferated on the surface of the various ESBS membranes and the population doubling time for fibroblast culture decreased.

  19. Novel block, graft and random copolymers for biomedical applications

    DEFF Research Database (Denmark)

    Javakhishvili, Irakli; Jankova Atanasova, Katja; Tanaka, Masaru;

    Despite the simple structure, poly(2-methoxyethyl acrylate) (PMEA) shows excellent blood compatibility [1]. Both the freezing-bound water (intermediate water: preventing the biocomponents from directly contacting the polymer surface) and non-freezing water on the polymer surface play important ro...... copolymers with MMA [4] utilizing ATRP. Here we present other block, graft and random copolymers of MEA intended for biomedical applications. These macromolecular architectures have been constructed by employing controlled radical polymerization methods such as RAFT and ATRP....... roles for this [2]. An artificial lung (oxygenator), already in use, is coated with high MW PMEA prepared by radical polymerization with AIBN [2]. To broaden the possibilities for designing biomedical devices [3] and inspired from these findings we first prepared homo polymers of MEA and their block...

  20. Preparation of Pickering Double Emulsions Using Block Copolymer Worms

    OpenAIRE

    Thompson, Kate L.; Mable, Charlotte J.; Lane, Jacob A.; Derry, Mathew J.; Fielding, Lee A.; Armes, Steven P.

    2015-01-01

    The rational formulation of Pickering double emulsions is described using a judicious combination of hydrophilic and hydrophobic block copolymer worms as highly anisotropic emulsifiers. More specifically, RAFT dispersion polymerization was utilized to prepare poly(lauryl methacrylate)–poly(benzyl methacrylate) worms at 20% w/w solids in n-dodecane and poly(glycerol monomethacrylate)–poly(2-hydroxypropyl methacrylate)–poly(benzyl methacrylate) worms at 13% w/w solids in water by polymerization...

  1. Transient instability upon temperature quench in weakly ordered block copolymers

    OpenAIRE

    Qi, Shuyan; Wang, Zhen-Gang

    1999-01-01

    We report a novel transient instability upon temperature quench in weakly ordered block copolymer microphases possessing a soft direction or directions, such as the lamellar and hexagonal cylinder (HEX) phases. We show that reequilibration of the order parameter is accompanied by transient long wavelength undulation of the layers or cylinders—with an initial wavelength that depends on the depth of the temperature quench—that eventually disappears as the structure reaches its equilibrium at th...

  2. Block and Graft Copolymers Containing Carboxylate or Phosphonate Anions

    OpenAIRE

    Hu, Nan

    2014-01-01

    This dissertation focuses on synthesis and characterization of graft and block copolymers containing carboxylate or phosphonate anions that are potential candidates for biomedical applications such as drug delivery and dental adhesives. Ammonium bisdiethylphosphonate (meth)acrylate and acrylamide phosphonate monomers were synthesized based on aza-Michael addition reactions. Free radical copolymerizations of these monomers with an acrylate-functional poly(ethylene oxide) (PEO) macromonomer...

  3. Preparation of amphiphilic block copolymer containing triazene moieties and fluorescence study

    Indian Academy of Sciences (India)

    Emil C Buruiana; Andreea L Chibac; Violeta Melinte; Tinca Buruiana

    2013-01-01

    The present study describes the synthesis via microwave accelerated reversible additionfragmentation chain transfer (RAFT) polymerization of an amphiphilic block copolymer poly(acrylic acid)-b-poly(dodecylacrylamide-co-1-(phenyl)-3-(2-methacryloyloxyethyl carbamoyloxyethyl)-3-methyltriazene-1) [PAA-b-(PDA-co-PUMA-T)]. The structure and the chemical composition of the block copolymer were confirmed by spectral/thermal analysis. The photoreactivity of the triazene sequences from PAA-b-(PDA-co-PUMA-T) was quantified by UV/vis irradiation in chloroform/dimethylformamide solutions and in thin film, indicating that the solvent polarity modifies with an order of magnitude the rate constant values. The lower rate constant in film state (film = 1.3 × 10−3 s-1), shows that the higher mobility of polymeric chains in solution allow a more rapid orientation, favourable to the triazene bond cleavage. The capability of block copolymer to form micelles in aqueous environment and implicitly, its critical micelle concentration (CMC) was evidenced through fluorescence measurements using pyrene probe (10-6 M), the CMC value being of 4.64 × 10−3 g L-1 PAA--(PDA--PUMA-T) (3.27 × 10−7 M). Experiments of fluorescence quenching with various metal cations (UO$^{2+}_{2}$, Fe2+, Fe3+, Ni2+, Cu2+, Co2+, Pb2+ and Hg2+) suggested that such a block copolymer could find applications as fluorescence-based chemosensor for the detection of iron cations in homogeneous organic solutions or aqueous environments by thin films.

  4. Electrically Tunable Soft-Solid Block Copolymer Structural Color.

    Science.gov (United States)

    Park, Tae Joon; Hwang, Sun Kak; Park, Sungmin; Cho, Sung Hwan; Park, Tae Hyun; Jeong, Beomjin; Kang, Han Sol; Ryu, Du Yeol; Huh, June; Thomas, Edwin L; Park, Cheolmin

    2015-12-22

    One-dimensional photonic crystals based on the periodic stacking of two different dielectric layers have been widely studied, but the fabrication of mechanically flexible polymer structural color (SC) films, with electro-active color switching, remains challenging. Here, we demonstrate free-standing electric field tunable ionic liquid (IL) swollen block copolymer (BCP) films. Placement of a polymer/ionic liquid film-reservoir adjacent to a self-assembled poly(styrene-block-quaternized 2-vinylpyridine) (PS-b-QP2VP) copolymer SC film allowed the development of red (R), green (G), and blue (B) full-color SC block copolymer films by swelling of the QP2VP domains by the ionic liquid associated with water molecules. The IL-polymer/BCP SC film is mechanically flexible with excellent color stability over several days at ambient conditions. The selective swelling of the QP2VP domains could be controlled by both the ratio of the IL to a polymer in the gel-like IL reservoir layer and by an applied voltage in the range of -3 to +6 V using a metal/IL reservoir/SC film/IL reservoir/metal capacitor type device. PMID:26505787

  5. Donor-Acceptor Block Copolymers: Synthesis and Solar Cell Applications

    Directory of Open Access Journals (Sweden)

    Kazuhiro Nakabayashi

    2014-04-01

    Full Text Available Fullerene derivatives have been widely used for conventional acceptor materials in organic photovoltaics (OPVs because of their high electron mobility. However, there are also considerable drawbacks for use in OPVs, such as negligible light absorption in the visible-near-IR regions, less compatibility with donor polymeric materials and high cost for synthesis and purification. Therefore, the investigation of non-fullerene acceptor materials that can potentially replace fullerene derivatives in OPVs is increasingly necessary, which gives rise to the possibility of fabricating all-polymer (polymer/polymer solar cells that can deliver higher performance and that are potentially cheaper than fullerene-based OPVs. Recently, considerable attention has been paid to donor-acceptor (D-A block copolymers, because of their promising applications as fullerene alternative materials in all-polymer solar cells. However, the synthesis of D-A block copolymers is still a challenge, and therefore, the establishment of an efficient synthetic method is now essential. This review highlights the recent advances in D-A block copolymers synthesis and their applications in all-polymer solar cells.

  6. Structural and Luminescence Properties of Lu2O3:Eu3+ F127 Tri-Block Copolymer Modified Thin Films Prepared by Sol-Gel Method

    Directory of Open Access Journals (Sweden)

    María Luz Carrera Jota

    2013-02-01

    Full Text Available Lu2O3:Eu3+ transparent, high density, and optical quality thin films were prepared using the sol-gel dip-coating technique, starting with lutetium and europium nitrates as precursors and followed by hydrolysis in an ethanol-ethylene glycol solution. Acetic acid and acetylacetonate were incorporated in order to adjust pH and as a sol stabilizer. In order to increment the thickness of the films and orient the structure, F127 Pluronic acid was incorporated during the sol formation. Structural, morphological, and optical properties of the films were investigated for different F127/Lu molar ratios (0–5 in order to obtain high optical quality films with enhanced thickness compared with the traditional method. X-ray diffraction (XRD shows that the films present a highly oriented cubic structure beyond 1073 K for a 3-layer film, on silica glass substrates. The thickness, density, porosity, and refractive index evolution of the films were investigated by means of m-lines microscopy along with the morphology by scanning electron microscope (SEM and luminescent properties.

  7. Preparation and icephobic properties of polymethyltrifluoropropylsiloxane–polyacrylate block copolymers

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xiaohui; Zhao, Yunhui [School of Materials Science and Engineering, and Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin 300072 (China); Li, Hui [School of Chemistry and Chemical Engineering, Shandong Key Laboratory of Fluorine Chemistry and Chemical Engineering Materials, University of Jinan, Jinan 250022 (China); Yuan, Xiaoyan, E-mail: xyuan28@yahoo.com [School of Materials Science and Engineering, and Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin 300072 (China)

    2014-10-15

    Highlights: • PMTFPS–b-polyacrylate copolymers in five different compositions were synthesized. • Enrichment of PMTFPS amounts at the surface made high F/Si value. • Icing delay time was related to the surface roughness. • Ice shear strength was decreased by the synergistic effect of silicone and fluorine. - Abstract: Five polymethyltrifluoropropylsiloxane (PMTFPS)–polyacrylate block copolymers (PMTFPS–b-polyacrylate) were synthesized by free radical polymerization of methyl methacrylate, n-butyl acrylate and hydroxyethyl methacrylate using PMTFPS macroazoinitiator (PMTFPS-MAI) in range of 10–50 mass percentages. The morphology, surface chemical composition and wettability of the prepared copolymer films were investigated by transmission electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy, and water contact angle measurement. Delayed icing time and ice shear strength of the films were also detected for the icephobic purpose. The surface morphologies of the copolymers were different from those of the bulk because of the migration of the PMTFPS segments to the air interface during the film formation. Maximal delayed icing time (186 s at −15 °C) and reduction of the ice shear strength (301 ± 10 kPa) which was significantly lower than that of polyacrylates (804 ± 37 kPa) were achieved when the content of PMTFPS-MAI was 20 wt%. The icephobicity of the copolymers was attributed primarily to the enrichment of PMTFPS on the film surface and synergistic effect of both silicone and fluorine. Thus, the results show that the PMTFPS–b-polyacrylate copolymer can be used as icephobic coating materials potentially.

  8. Rapid, Brushless Self-assembly of a PS-b-PDMS Block Copolymer for Nanolithography

    DEFF Research Database (Denmark)

    Rasappa, Sozaraj; Schulte, Lars; Borah, Dipu;

    2014-01-01

    antidot patterns after short solvo-thermal annealing. Unlike previous reports on this system, low temperature and short annealing time provide self-assembly in homogeneous thin films covering large substrate areas. This on-chip mask was then used for pattern transfer to the underlying silicon substrate......Block copolymers (BCP) are highly promising self-assembling precursors for scalable nanolithography. Very regular BCP nanopatterns can be used as on-chip etch masks. The first step in the processing of BCP thin films is usually the chemical modification of the substrate surface, typically by...... grafting of a brush layer that renders the surface energy neutral relative to the constituent blocks. We provide here a first study on rapid, low temperature self-assembly of PS-b-PDMS (polystyrene-block-polydimethylsiloxane) on silicon substrates without a brush layer. We show that it forms line and...

  9. Effect of block composition on thermal properties and melt viscosity of poly[2-(dimethylaminoethyl methacrylate], poly(ethylene oxide and poly(propylene oxide block co-polymers

    Directory of Open Access Journals (Sweden)

    2011-09-01

    Full Text Available To modify the rheological properties of certain commercial polymers, a set of block copolymers were synthesized through oxyanionic polymerization of 2-(dimethylaminoethyl methacrylate to the chain ends of commercial prepolymers, namely poly(ethylene oxide (PEO, poly(ethylene oxide-block-poly(propylene oxide-block-poly(ethylene oxide (PEO-PPO-PEO, and poly(propylene oxide (PPO. The formed block copolymers were analysed with size exclusion chromatography and nuclear magnetic resonance spectroscopy in order to confirm block formation. Thermal characterization of the resulting polymers was done with differential scanning calorimetry. Thermal transition points were also confirmed with rotational rheometry, which was primarily used to measure melt strength properties of the resulting block co-polymers. It was observed that the synthesised poly[2-(dimethylaminoethyl methacrylate]-block (PDM affected slightly the thermal transition points of crystalline PEO-block but the influence was stronger on amorphous PPO-blocks. Frequency sweeps measured above the melting temperatures for the materials confirmed that the pre-polymers (PEO and PEO-PPO-PEO behave as Newtonian fluids whereas polymers with a PDM block structure exhibit clear shear thinning behaviour. In addition, the PDM block increased the melt viscosity when compared with that one of the pre-polymer. As a final result, it became obvious that pre-polymers modified with PDM were in entangled form, in the melted state as well in the solidified form.

  10. Metal Nanoparticle/Block Copolymer Composite Assembly and Disassembly

    OpenAIRE

    Li, Zihui; Sai, Hiroaki; Warren, Scott C.; Kamperman, Marleen; Arora, Hitesh; Gruner, Sol M.; Wiesner, Ulrich

    2009-01-01

    Ligand-stabilized platinum nanoparticles (Pt NPs) were self-assembled with poly(isoprene-block-dimethylaminoethyl methacrylate) (PI-b-PDMAEMA) block copolymers to generate organic-inorganic hybrid materials. High loadings of NPs in hybrids were achieved through usage of N,N-di-(2-(allyloxy)ethyl)-N-3-mercaptopropyl-N-3-methylammonium chloride as the ligand, which provided high solubility of NPs in various solvents as well as high affinity to PDMAEMA. From NP synthesis, existence of sub-1 nm P...

  11. Redox-controlled micellization of organometallic block copolymers.

    Science.gov (United States)

    Rider, David A; Winnik, Mitchell A; Manners, Ian

    2007-11-21

    Polystyrene-block-polyferrocenylsilane (PS-b-PFS) diblock copolymers were stoichiometrically oxidized in solution using salts of the one-electron oxidant tris(4-bromophenyl)ammoniumyl. Due to a redox-induced polarity change for the PFS block, self-assembly into well-defined spherical micelles occurs. The micelles are composed of a core of partially oxidized PFS segments and a corona of PS. When the micellar solutions were treated with the reducing agent decamethylcobaltocene, the spherical micelles disassemble and regenerate unassociated and pristine PS-b-PFS free chains. PMID:17971963

  12. Photoresponsive Block Copolymers Containing Azobenzenes and Other Chromophores

    Directory of Open Access Journals (Sweden)

    Takaomi Kobayashi

    2010-01-01

    Full Text Available Photoresponsive block copolymers (PRBCs containing azobenzenes and other chromophores can be easily prepared by controlled polymerization. Their photoresponsive behaviors are generally based on photoisomerization, photocrosslinking, photoalignment and photoinduced cooperative motions. When the photoactive block forms mesogenic phases upon microphase separation of PRBCs, supramolecular cooperative motion in liquid-crystalline PRBCs enables them to self-organize into hierarchical structures with photoresponsive features. This offers novel opportunities to photocontrol microphase-separated nanostructures of well-defined PRBCs and extends their diverse applications in holograms, nanotemplates, photodeformed devices and microporous films.

  13. Block copolymers for alkaline fuel cell membrane materials

    Science.gov (United States)

    Li, Yifan

    Alkaline fuel cells (AFCs) using anion exchange membranes (AEMs) as electrolyte have recently received considerable attention. AFCs offer some advantages over proton exchange membrane fuel cells, including the potential of non-noble metal (e.g. nickel, silver) catalyst on the cathode, which can dramatically lower the fuel cell cost. The main drawback of traditional AFCs is the use of liquid electrolyte (e.g. aqueous potassium hydroxide), which can result in the formation of carbonate precipitates by reaction with carbon dioxide. AEMs with tethered cations can overcome the precipitates formed in traditional AFCs. Our current research focuses on developing different polymer systems (blend, block, grafted, and crosslinked polymers) in order to understand alkaline fuel cell membrane in many aspects and design optimized anion exchange membranes with better alkaline stability, mechanical integrity and ionic conductivity. A number of distinct materials have been produced and characterized. A polymer blend system comprised of poly(vinylbenzyl chloride)-b-polystyrene (PVBC-b-PS) diblock copolymer, prepared by nitroxide mediated polymerization (NMP), with poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) or brominated PPO was studied for conversion into a blend membrane for AEM. The formation of a miscible blend matrix improved mechanical properties while maintaining high ionic conductivity through formation of phase separated ionic domains. Using anionic polymerization, a polyethylene based block copolymer was designed where the polyethylene-based block copolymer formed bicontinuous morphological structures to enhance the hydroxide conductivity (up to 94 mS/cm at 80 °C) while excellent mechanical properties (strain up to 205%) of the polyethylene block copolymer membrane was observed. A polymer system was designed and characterized with monomethoxy polyethylene glycol (mPEG) as a hydrophilic polymer grafted through substitution of pendent benzyl chloride groups of a PVBC

  14. Biodegradable PELA block copolymers: in vitro degradation and tissue reaction.

    Science.gov (United States)

    Younes, H; Nataf, P R; Cohn, D; Appelbaum, Y J; Pizov, G; Uretzky, G

    1988-01-01

    Degradation of, and tissue reaction elicited by a series of polyethylene oxide (PEO)/polylactic acid (PLA) PELA block copolymers were studied in vitro and in vivo. In particular, the effect of pH, temperature and enzymatic activity was addressed. The mass loss was faster, the more basic the media, while, expectedly, PELA copolymers degraded faster with the higher temperature. The addition of an enzyme (carboxylic ester hydrolase) had no effect. The degradation process strongly affected the mechanical properties of the materials under investigation, the elongation at break dropping drastically after two days of degradation. After seven days, only gross observation of the extensively degraded samples was possible. The in vivo studies compared the tissue reaction elicited by various PELA copolymers to that evoked by PLA. Evaluation of tissue reaction observed with a PELA sample after sterilization with gamma radiation showed acute inflammation with considerable dispersion of the material, 12 days after implantation. The granulomatous reaction observed with PELA copolymers after ethylene oxide sterilization was identical to the reaction observed with PLA. PMID:3064826

  15. Morphology and Proton Transport in Humidified Phosphonated Peptoid Block Copolymers

    Science.gov (United States)

    2016-01-01

    Polymers that conduct protons in the hydrated state are of crucial importance in a wide variety of clean energy applications such as hydrogen fuel cells and artificial photosynthesis. Phosphonated and sulfonated polymers are known to conduct protons at low water content. In this paper, we report on the synthesis phosphonated peptoid diblock copolymers, poly-N-(2-ethyl)hexylglycine-block-poly-N-phosphonomethylglycine (pNeh-b-pNpm), with volume fractions of pNpm (ϕNpm) values ranging from 0.13 to 0.44 and dispersity (Đ) ≤ 1.0003. The morphologies of the dry block copolypeptoids were determined by transmission electron microscopy and in both the dry and hydrated states by synchrotron small-angle X-ray scattering. Dry samples with ϕNpm > 0.13 exhibited a lamellar morphology. Upon hydration, the lowest molecular weight sample transitioned to a hexagonally packed cylinder morphology, while the others maintained their dry morphologies. Water uptake of all of the ordered samples was 8.1 ± 1.1 water molecules per phosphonate group. In spite of this, the proton conductivity of the ordered pNeh-b-pNpm copolymers ranged from 0.002 to 0.008 S/cm. We demonstrate that proton conductivity is maximized in high molecular weight, symmetric pNeh-b-pNpm copolymers. PMID:27134312

  16. Sub-15nm Silicon Lines Fabrication via PS-b-PDMS Block Copolymer Lithography

    DEFF Research Database (Denmark)

    Rasappa, Sozaraj; Schulte, Lars; Borah, Dipu;

    2013-01-01

    This paper describes the fabrication of nanodimensioned silicon structures on silicon wafers from thin films of a poly(styrene)-block-poly(dimethylsiloxane) (PS-b-PDMS) block copolymer (BCP) precursor self-assembling into cylindrical morphology in the bulk. The structure alignment of the PS-b-PDM...... subsequent plasma etching to the underlying substrate by an anisotropic dry etching process. SEM images reveal the formation of silicon nanostructures, notably of sub-15nm dimensions.......This paper describes the fabrication of nanodimensioned silicon structures on silicon wafers from thin films of a poly(styrene)-block-poly(dimethylsiloxane) (PS-b-PDMS) block copolymer (BCP) precursor self-assembling into cylindrical morphology in the bulk. The structure alignment of the PS......-b-PDMS (33 k–17 k) was conditioned by applying solvent and solvothermal annealing techniques. BCP nanopatterns formed after the annealing process have been confirmed by scanning electron microscope (SEM) after removal of upper PDMS wetting layer by plasma etching. Silicon nanostructures were obtained by...

  17. Metal Nanoparticle/Block Copolymer Composite Assembly and Disassembly.

    Science.gov (United States)

    Li, Zihui; Sai, Hiroaki; Warren, Scott C; Kamperman, Marleen; Arora, Hitesh; Gruner, Sol M; Wiesner, Ulrich

    2009-01-01

    Ligand-stabilized platinum nanoparticles (Pt NPs) were self-assembled with poly(isoprene-block-dimethylaminoethyl methacrylate) (PI-b-PDMAEMA) block copolymers to generate organic-inorganic hybrid materials. High loadings of NPs in hybrids were achieved through usage of N,N-di-(2-(allyloxy)ethyl)-N-3-mercaptopropyl-N-3-methylammonium chloride as the ligand, which provided high solubility of NPs in various solvents as well as high affinity to PDMAEMA. From NP synthesis, existence of sub-1 nm Pt NPs was confirmed by high-angle annular dark field scanning transmission electron microscopy (HAADF-STEM) images. Estimations of the Pt NP ligand head group density based on HAADF-STEM images and thermogravimetric analysis (TGA) data yielded results comparable to what has been found for alkanethiol self-assembled monolayers (SAMs) on flat Pt {111} surfaces. Changing the volume fraction of Pt NPs in block copolymer-NP composites yielded hybrids with spherical micellar, wormlike micellar, lamellar and inverse hexagonal morphologies. Disassembly of hybrids with spherical, wormlike micellar, and lamellar morphologies generated isolated metal-NP based nano-spheres, cylinders and sheets, respectively. Results suggest the existence of powerful design criteria for the formation of metal-based nanostructures from designer blocked macromolecules. PMID:21103025

  18. Triazene UV-triggered photogeneration of silver/gold nanoparticles in block copolymer templates

    Energy Technology Data Exchange (ETDEWEB)

    Melinte, Violeta; Chibac, Andreea; Buruiana, Tinca; Hitruc, Gabriela; Buruiana, Emil C., E-mail: emilbur@icmpp.ro [Petru Poni Institute of Macromolecular Chemistry, Polyaddition and Photochemistry Department (Romania)

    2015-10-15

    This article describes an attractive way to in situ create noble metal nanoparticles in block copolymer matrixes through the UV-triggered photodecomposition of the photolabile triazene units without the use of any conventional reducing agent. The poly(isodecyl methacrylate-co-triazene urethane methacrylate) random copolymer containing pendent photocleavable triazene junctions (COP-1) was synthesized under RAFT conditions and subsequently employed as macroinitiator to obtain a block copolymer, namely poly(isodecyl methacrylate-co-triazene urethane methacrylate)-block-poly(acrylic acid) (COP-2). The photogeneration of silver/gold metal nanoparticles (NPs) from noble metal precursors (1 wt% AgNO{sub 3} or AuBr{sub 3} metal salts) induced through the UV decomposition of triazene units with the formation of some radical active species was monitored in solution and thin films. The in situ growth of Ag/Au nanostructures into polymer matrixes for which the light is a key element has been confirmed by UV spectroscopy and TEM analysis. The TEM images allowed the visualization of the silver NPs (sizes of 4–16 nm in COP-1 and of 2–6 nm in COP-2) as well as of the gold NPs (sizes between 10 and 20 nm in COP-1 and from 15 to 25 nm in COP-2), which are mainly spherical in shape, even though there is some triangular or hexagonal gold nanoparticles.

  19. Triazene UV-triggered photogeneration of silver/gold nanoparticles in block copolymer templates

    International Nuclear Information System (INIS)

    This article describes an attractive way to in situ create noble metal nanoparticles in block copolymer matrixes through the UV-triggered photodecomposition of the photolabile triazene units without the use of any conventional reducing agent. The poly(isodecyl methacrylate-co-triazene urethane methacrylate) random copolymer containing pendent photocleavable triazene junctions (COP-1) was synthesized under RAFT conditions and subsequently employed as macroinitiator to obtain a block copolymer, namely poly(isodecyl methacrylate-co-triazene urethane methacrylate)-block-poly(acrylic acid) (COP-2). The photogeneration of silver/gold metal nanoparticles (NPs) from noble metal precursors (1 wt% AgNO3 or AuBr3 metal salts) induced through the UV decomposition of triazene units with the formation of some radical active species was monitored in solution and thin films. The in situ growth of Ag/Au nanostructures into polymer matrixes for which the light is a key element has been confirmed by UV spectroscopy and TEM analysis. The TEM images allowed the visualization of the silver NPs (sizes of 4–16 nm in COP-1 and of 2–6 nm in COP-2) as well as of the gold NPs (sizes between 10 and 20 nm in COP-1 and from 15 to 25 nm in COP-2), which are mainly spherical in shape, even though there is some triangular or hexagonal gold nanoparticles

  20. Synthesis of segmented PB(SMA-block-PB)(n) block copolymers through a polymeric iniferter technique

    NARCIS (Netherlands)

    Kroeze, E; ten Brinke, G.; Hadziioannou, G

    1997-01-01

    A technique is described for the synthesis of segmented block copolymers of polybutadiene and poly(styrene-co-maleic anhydride) through a polymeric therma iniferter based on polybutadiene, which was used as an initiator for the thermal copolymerization of styrene and maleic anhydride. The polymeric

  1. Hybrid - block copolymer nanocomposites. characterization of nanostructure by small-angle X-ray scattering (SAXS)

    OpenAIRE

    A. Romo-Uribe

    2007-01-01

    The nanoscopic order of a series of block copolymer-inorganic nanocomposites was characterized using small-angle X-ray scattering (SAXS). The nanostructures were obtained via a diblock copolymer directed sol-gel synthesis. The copolymer consists of blocks of poly(isoprene) -PI- and blocks of poly(ethylene oxide) -PEO. The inorganic material consists of a crosslinked sol of 3-glycidoxypropyltrimethoxysilane and aluminum-tri-sec-butoxide in a 4:1 mole ratio, to generate an aluminosilicate ceram...

  2. High aspect ratio sub-15 nm silicon trenches from block copolymer templates.

    Science.gov (United States)

    Gu, Xiaodan; Liu, Zuwei; Gunkel, Ilja; Chourou, S T; Hong, Sung Woo; Olynick, Deirdre L; Russell, Thomas P

    2012-11-01

    High-aspect-ratio sub-15-nm silicon trenches are fabricated directly from plasma etching of a block copolymer mask. A novel method that combines a block copolymer reconstruction process and reactive ion etching is used to make the polymer mask. Silicon trenches are characterized by various methods and used as a master for subsequent imprinting of different materials. Silicon nanoholes are generated from a block copolymer with cylindrical microdomains oriented normal to the surface. PMID:22903820

  3. Microtome Sliced Block Copolymers and Nanoporous Polymers as Masks for Nanolithography

    OpenAIRE

    Shvets, Violetta; Schulte, Lars; Ndoni, Sokol

    2014-01-01

    Introduction. Block copolymers self-assembling properties are commonly used for creation of very fine nanostructures [1]. Goal of our project is to test new methods of the block-copolymer lithography mask preparation: macroscopic pieces of block-copolymers or nanoporous polymers with cross-linked phase are sliced with microtome and pattern is transfered from flakes to substrate by plasma etching.Experimental Section. Group of Self-organized Nanoporous Materials in Technical University of Denm...

  4. Tetragonal Ordering in Block Copolymer-Homopolymer Blend Films Laterally Confined in a Square Well

    Science.gov (United States)

    Hur, Su-Mi; García-Cervera, Carlos; Kramer, Ed; Fredrickson, Glenn

    2009-03-01

    Self-consistent field theory (SCFT) simulations are presented for a melt blend of AB diblock copolymers and A homopolymers in a thin film confined to a square well. The work aims to guide self-assembly towards tetragonal ordering, which is a pattern of technological interest in block copolymer lithography. By using suitable A homopolymer additives, we have succeeded in achieving square lattices of cylinders not observed in the confined or bulk pure diblock system. A phase diagram is presented that shows the region of stability of the tetragonal phase as a function of chain length and volume fraction of the homopolymer additive, in addition to several other interesting phases that result from a competition between surface and bulk contributions to the free energy. Results are also presented on the effect of line edge roughness in the square confinement well on the achievement of robust and defect free tetragonal order.

  5. Periodic nanoscale patterning of polyelectrolytes over square centimeter areas using block copolymer templates.

    Science.gov (United States)

    Oded, Meirav; Kelly, Stephen T; Gilles, Mary K; Müller, Axel H E; Shenhar, Roy

    2016-05-18

    Nano-patterned materials are beneficial for applications such as solar cells, opto-electronics, and sensing owing to their periodic structure and high interfacial area. Here, we present a non-lithographic approach for assembling polyelectrolytes into periodic nanoscale patterns over cm(2)-scale areas. Chemically modified block copolymer thin films featuring alternating charged and neutral domains are used as patterned substrates for electrostatic self-assembly. In-depth characterization of the deposition process using spectroscopy and microscopy techniques, including the state-of-the-art scanning transmission X-ray microscopy (STXM), reveals both the selective deposition of the polyelectrolyte on the charged copolymer domains as well as gradual changes in the film topography that arise from further penetration of the solvent molecules and possibly also the polyelectrolyte into these domains. Our results demonstrate the feasibility of creating nano-patterned polyelectrolyte layers, which opens up new opportunities for structured functional coating fabrication. PMID:27104854

  6. Perfluorocyclobutyl-containing Amphiphilic Block Copolymers Synthesized by RAFT Polymerization

    Institute of Scientific and Technical Information of China (English)

    LI, Yongjun; ZHANG, Sen; FENG, Chun; ZHANG, Yaqin; LI, Qingnuan; LI, Wenxin; HUANG, Xiaoyu

    2009-01-01

    Amphiphilic block copolymers containing hydrophobic perfluorocyclobutyl-based (PFCB) polyacrylate and hydrophilic poly(ethylene glycol) (PEG) segments were prepared via reversible addition-fragmentation chain transfer (RAP-T) polymerization. The PFCB-containing acrylate monomer, p-(2-(p-tolyloxy)perfluorocyclobutoxy)phenyl acrylate, was first synthesized from commercially available compounds in good yields, and this kind of acrylate monomer can be homopolymerized by free radical polymerization or RAFT polymerization. Kinetic study showed the 2,2'-azobis(isobutyronitrile) (AIBN) initiated and cumyl dithiobenzoate (CDB) mediated RAFT polymerization was in a living fashion, as suggested by the fact that the number-average molecular weights (M_n) increased linearly with the conversions of the monomer, while the polydispersity indices kept less than 1.10. The block polymers with narrow molecular weight distributions (M_w/M_n≤1.21) were prepared through RAFT polymerization using PEG monomethyl ether capped with 4-cyanopentanoic acid dithiobenzoate end group as the macro chain transfer agent (mPEG-CTA). The length of the hydrophobic segment can be tuned by the feed ratio of the PFCB-based acrylate monomer and the extending of the polymerization time. The micellization behavior of the block copolymers in aqueous media was investigated by the fluorescence probe technique.

  7. Designing block copolymer architectures for targeted membrane performance

    KAUST Repository

    Dorin, Rachel Mika

    2014-01-01

    Using a combination of block copolymer self-assembly and non-solvent induced phase separation, isoporous ultrafiltration membranes were fabricated from four poly(isoprene-b-styrene-b-4-vinylpyridine) triblock terpolymers with similar block volume fractions but varying in total molar mass from 43 kg/mol to 115 kg/mol to systematically study the effect of polymer size on membrane structure. Small-angle X-ray scattering was used to probe terpolymer solution structure in the dope. All four triblocks displayed solution scattering patterns consistent with a body-centered cubic morphology. After membrane formation, structures were characterized using a combination of scanning electron microscopy and filtration performance tests. Membrane pore densities that ranged from 4.53 × 1014 to 1.48 × 1015 pores/m 2 were observed, which are the highest pore densities yet reported for membranes using self-assembly and non-solvent induced phase separation. Hydraulic permeabilities ranging from 24 to 850 L m-2 h-1 bar-1 and pore diameters ranging from 7 to 36 nm were determined from permeation and rejection experiments. Both the hydraulic permeability and pore size increased with increasing molar mass of the parent terpolymer. The combination of polymer characterization and membrane transport tests described here demonstrates the ability to rationally design macromolecular structures to target specific performance characteristics in block copolymer derived ultrafiltration membranes. © 2013 Elsevier Ltd. All rights reserved.

  8. Self-assembly of block copolymers on topographically patterned polymeric substrates

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Thomas P.; Park, Soojin; Lee, Dong Hyun; Xu, Ting

    2016-05-10

    Highly-ordered block copolymer films are prepared by a method that includes forming a polymeric replica of a topographically patterned crystalline surface, forming a block copolymer film on the topographically patterned surface of the polymeric replica, and annealing the block copolymer film. The resulting structures can be used in a variety of different applications, including the fabrication of high density data storage media. The ability to use flexible polymers to form the polymeric replica facilitates industrial-scale processes utilizing the highly-ordered block copolymer films.

  9. Self-assembled isoporous block copolymer membranes with tuned pore sizes

    KAUST Repository

    Yu, Haizhou

    2014-07-23

    The combination of nonsolvent-induced phase separation and the self-assembly of block copolymers can lead to asymmetric membranes with a thin highly ordered isoporous skin layer. The effective pore size of such membranes is usually larger than 15 nm. We reduced the pore size of these membranes by electroless gold deposition. We demonstrate that the pore sizes can be controlled precisely between 3 and 20 nm leading to a tunable sharp size discrimination in filtration processes. Besides fractionation of nanoparticles and biomaterials, controlled drug delivery is an attractive potential application. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Characterization and micellization of a poloxamer block copolymer

    DEFF Research Database (Denmark)

    Hvidt, S.; Pedersen, Walther Batsberg

    2007-01-01

    Several poloxamers that are symmetrical EPE block copolymers (E and P are ethylene and propylene oxide, respectively) have been characterized by size exclusion chromatography on Superose columns in water. The poloxamers contain between 12 and 26 wt% of smaller-size UV-absorbing impurities....... Poloxamer P94 (E28P48E28) forms micelles with increasing temperature, and micellization was investigated by eluent gel permeation chromatography (EGPC). EGPC results demonstrate that P94 impurities are not incorporated into the micelles up to 38°C. The importance of poloxamer heterogeneity for thermodynamic...

  11. Self-assembly in casting solutions of block copolymer membranes

    KAUST Repository

    Marques, Debora S.

    2013-01-01

    Membranes with exceptional pore regularity and high porosity were obtained from block copolymer solutions. We demonstrate by small-angle X-ray scattering that the order which gives rise to the pore morphology is already incipient in the casting solution. Hexagonal order was confirmed in PS-b-P4VP 175k-b-65k solutions in DMF/THF/dioxane with concentrations as high as 24 wt%, while lamellar structures were obtained in more concentrated solutions in DMF or DMF/dioxane. The change in order has been understood with the support of dissipative particle dynamic modeling. © 2013 The Royal Society of Chemistry.

  12. (Electro)Mechanical Properties of Olefinic Block Copolymers

    Science.gov (United States)

    Spontak, Richard

    2014-03-01

    Conventional styrenic triblock copolymers (SBCs) swollen with a midblock-selective oil have been previously shown to exhibit excellent electromechanical properties as dielectric elastomers. In this class of electroactive polymers, compliant electrodes applied as active areas to opposing surfaces of an elastomer attract each other, and thus compress the elastomer due to the onset of a Maxwell stress, upon application of an external electric field. This isochoric process is accompanied by an increase in lateral area, which yields the electroactuation strain (measuring beyond 300% in SBC systems). Performance parameters such as the Maxwell stress, transverse strain, dielectric breakdown, energy density and electromechanical efficiency are determined directly from the applied electric field and resulting electroactuation strain. In this study, the same principle used to evaluate SBC systems is extended to olefinic block copolymers (OBCs), which can be described as randomly-coupled multiblock copolymers that consist of crystallizable polyethylene hard segments and rubbery poly(ethylene-co-octene) soft segments. Considerations governing the development of a methodology to fabricate electroresponsive OBC systems are first discussed for several OBCs differing in composition and bulk properties. Evidence of electroactuation in selectively-solvated OBC systems is presented and performance metrics measured therefrom are quantitatively compared with dielectric elastomers derived from SBC and related materials.

  13. Tough Block Copolymer Organogels and Elastomers as Short Fiber Composites

    Science.gov (United States)

    Kramer, Edward J.

    2012-02-01

    The origins of the exceptional toughness and elastomeric properties of gels and elastomers from block copolymers with semicrystalline syndiotactic polypropylene blocks will be discussed. Using synchrotron X-radiation small angle (SAXS) and wide angle X-ray scattering (WAXS) experiments were simultaneously performed during step cycle tensile deformation of these elastomers and gels. From these results the toughness can be attributed to the formation, orientation and elongation of the crystalline fibrils along the tensile direction. The true stress and true strain ɛH during each cycle were recorded, including the true strain at zero load ɛH,p after each cycle that resulted from the plastic deformation of the sPP crystals in the gel or elastomer. The initial Young's modulus Einit and maximum tangent modulus Emax in each cycle undergo dramatic changes as a function of ɛH,p, with Einit decreasing for ɛH,p 100 to 1000 at the highest maximum (nominal) strain. Based on SAXS patterns from the deformed and relaxed gels, as well as on previous results on deformation of semicrystalline random copolymers by Strobl and coworkers, we propose that the initial decrease in Einit and increase in Emax with ɛH,p are due to a breakup of the network of the original sPP crystal lamellae and the conversion of the sPP lamellae into fibrils whose aspect ratio increases with further plastic deformation, respectively. The gel elastic properties can be understood quantitatively as those of a short fiber composite with a highly deformable matrix. At zero stress the random copolymer midblock chains that connect the fibrils cause these to make all angles to the tensile axis (low Einit), while at the maximum strain the stiff, crystalline sPP fibrils align with the tensile axis producing a strong, relatively stiff gel. The evolution of the crystalline structure during deformation is confirmed by WAXS and FTIR measurements.

  14. Silver-enhanced block copolymer membranes with biocidal activity

    KAUST Repository

    Madhavan, Poornima

    2014-11-12

    Silver nanoparticles were deposited on the surface and pore walls of block copolymer membranes with highly ordered pore structure. Pyridine blocks constitute the pore surfaces, complexing silver ions and promoting a homogeneous distribution. Nanoparticles were then formed by reduction with sodium borohydride. The morphology varied with the preparation conditions (pH and silver ion concentration), as confirmed by field emission scanning and transmission electron microscopy. Silver has a strong biocide activity, which for membranes can bring the advantage of minimizing the growth of bacteria and formation of biofilm. The membranes with nanoparticles prepared under different pH values and ion concentrations were incubated with Pseudomonas aeruginosa and compared with the control. The strongest biocidal activity was achieved with membranes containing membranes prepared under pH 9. Under these conditions, the best distribution with small particle size was observed by microscopy.

  15. Controlling thermochromism in a photonic block copolymer gel.

    Science.gov (United States)

    Walish, Joseph J; Fan, Yin; Centrone, Andrea; Thomas, Edwin L

    2012-09-26

    The tunable properties of stimulus-responsive materials attract great interest in a variety of technological applications. Photonic gels are a new class of these materials, which can be tuned to reflect different wavelengths of light. Controlling this reflected color via temperature-induced changes of self-assembled photonic materials is important for their application in sensors and displays. In this work, the thermochromic behavior of a PS-P2VP photonic gel was found to originate from a temperature-induced change in the pK(a) of the P2VP blocks. Control was obtained through the manipulation of the solution pH. The findings of this work provide the basis for understanding and controlling the properties of thermochromic block copolymers fostering their use in technologically relevant applications. PMID:22763921

  16. Chirality in block copolymer melts: mesoscopic helicity from intersegment twist.

    Science.gov (United States)

    Zhao, Wei; Russell, Thomas P; Grason, Gregory M

    2013-02-01

    We study the effects of chirality at the segment scale on the thermodynamics of block copolymer melts using self-consistent field theory. In linear diblock melts where segments of one block prefer a twisted, or cholesteric, texture, we show that melt assembly is critically sensitive to the ratio of random coil size to the preferred pitch of cholesteric twist. For weakly chiral melts (large pitch), mesophases remain achiral, while below a critical value of pitch, two mesoscopically chiral phases are stable: an undulated lamellar phase and a phase of hexagonally ordered helices. We show that the nonlinear sensitivity of mesoscale chiral order to preferred pitch derives specifically from the geometric and thermodynamic coupling of the helical mesodomain shape to the twisted packing of chiral segments within the core, giving rise to a second-order cylinder-to-helix transition. PMID:23414052

  17. Characterizing the interfaces of block copolymers with high χ

    Science.gov (United States)

    Sunday, Daniel; Maher, Michael; Blachut, Gregory; Asano, Yusuke; Tein, Summer; Willson, C. Grant; Ellison, Christopher; Kline, R. Joseph

    In order for block copolymer (BCP) directed self-assembly (DSA) to be able to pattern features below 10 nm there must be materials which can spontaneously assembly at the required length scales. For the smallest features this will require phase separation where the total chain lengths are under 50 monomer units, demanding very large interaction parameters (χ) to have an order-disorder transition. One of the key parameters for DSA will be the interfacial width between the blocks, which is expected to be correlated to the interaction parameter and will help determine the line edge roughness (LER). We have used resonant soft X-ray reflectivity to investigate a series of high χ BCPs with different compositions and molecular weights to determine the interfacial width and degree of phase separation. We use these results to estimate the value of χ and determine relationships between χ and the interfacial mixing.

  18. Morphological evolution of lamellar forming polystyrene-block-poly(4-vinylpyridine) copolymers under solvent annealing.

    Science.gov (United States)

    Ghoshal, Tandra; Chaudhari, Atul; Cummins, Cian; Shaw, Matthew T; Holmes, Justin D; Morris, Michael A

    2016-06-28

    In this work, we are reporting a very simple and efficient method to form lamellar structures of symmetric polystyrene-block-poly(4-vinylpyridine) (PS-b-P4VP) copolymer thin films with vertically (to the surface plane) orientated lamellae using a solvent annealing approach. The methodology does not require any brush chemistry to engineer a neutral surface and it is the block neutral nature of the film-solvent vapour interface that defines the orientation of the lamellae. The microphase separated structure of two different molecular weight lamellar forming PS-block-P4VP copolymers formed under solvent vapour annealing was monitored using atomic force microscopy (AFM) so as to understand the morphological changes of the films upon different solvent exposure. In particular, the morphology changes from micellar structures to well-defined microphase separated arrangements. The choice of solvent/s (single and dual solvent exposure) and the solvent annealing conditions (temperature, time etc.) has important effects on structural transitions of the films and it was found that a block neutral solvent was required to realize vertically aligned P4VP lamellae. The results of the structural variation of the phase separated nanostructured films through the exposure to ethanol are also described. PMID:27240904

  19. Transport of Water in Semicrystalline Block Copolymer Membranes

    Science.gov (United States)

    Hallinan, Daniel; Oparaji, Onyekachi

    Poly(styrene)-block-poly(ethylene oxide) (PS- b-PEO) is a semicrystalline block copolymer (BCP) with interesting properties. It is mechanically tough, amphiphilic, and has a polar phase. The mechanical toughness is due to the crystallinity of PEO and the high glass transition temperature of PS, as well as the morphological structure of the BCP. The polymer has high CO2, water, and salt solubility that derive from the polar PEO component. Potential applications include CO2 separation, water purification, and lithium air batteries. In all of the aforementioned applications, water transport is an important parameter. The presence of water can also affect thermal and mechanical properties. Water transport and thermal and mechanical properties of a lamellar PS- b-PEO copolymer have been measured as a function of water activity. Water transport can be affected by the heterogeneous nature of a semicrystalline BCP. Therefore, Fourier transform infrared - attenuated total reflectance (FTIR-ATR) spectroscopy has been employed, because water transport and polymer swelling can be measured simultaneously. The effect of BCP structure on transport has been investigated by comparing water transport in PS- b-PEO to a PEO homopolymer. The crystalline content of the PEO and the presence of glassy PS lamellae will be used to explain the transport results.

  20. Topology and Shape Control for Assemblies of Block Copolymer Blends in Solution

    KAUST Repository

    Moreno, Nicolas

    2015-10-27

    We study binary blends of asymmetric diblock copolymers (AB/AC) in selective solvents with a mesoscale model. We investigate the morphological transitions induced by the concentration of the AC block copolymer and the difference in molecular weight between the AB and AC copolymers, when segments B and C exhibit hydrogen-bonding interactions. To the best of our knowledge, this is the first work modeling mixtures of block copolymers with large differences in molecular weight. The coassembly mechanism localizes the AC molecules at the interface of A and B domains and induces the swelling of the B-rich domains. The coil size of the large molecular weight block copolymer depends only on the concentration of the short block copolymer (AC or AB), regardless of the B–C interactions. However, the B–C interactions control the morphological transitions that occur in these blends.

  1. PRECISE SYNTHESIS OF OLEFIN BLOCK COPOLYMERS USING A SYNDIOSPECIFIC LIVING POLYMERIZATION SYSTEM

    Institute of Scientific and Technical Information of China (English)

    Zheng-guo Cai; Hai-hui Su; Takeshi Shiono

    2013-01-01

    This feature article summarizes the synthesis of novel olefin block copolymers using fast syndiospecific living homo-and copolymerization of propylene,higher 1-alkene,and norbomene with ansa-fluorenylamidodimethyltitaniumbased catalyst according to the authors' recent results.The catalytic synthesis of monodisperse polyolefin and olefin block copolymer was also described using this living system.

  2. Light scattering from block copolymer melts near the order-disorder transition

    Czech Academy of Sciences Publication Activity Database

    Štěpánek, Petr; Lodge, T. P.; Bates, F. S.

    1994-01-01

    Roč. 2, - (1994), s. 110. ISSN 0009-2347. [Symposium Block Copolymer Dynamics, Chain Dynamics of Block Copolymers: Dynamics near the Ordering Transition. San Diego, 13.03.1994-18.03.1994] R&D Projects: GA AV ČR IA45023 Impact factor: 0.331, year: 1994

  3. Polarizability of DNA Block Copolymer Nanoparticles Observed by Electrostatic Force Microscopy

    NARCIS (Netherlands)

    Sowwan, Mukhles; Faroun, Maryam; Mentovich, Elad; Ibrahim, Imad; Haboush, Shayma; Alemdaroglu, Fikri Emrah; Kwak, Minseok; Richter, Shachar; Herrmann, Andreas

    2010-01-01

    In this study, DNA block copolymer (DBC) micelles with a polystyrene (PS) core and a single-stranded (ss) DNA shell were doped with ferrocene (Fc) molecules. Tapping mode atomic force microscopy (AFM) was used to study the morphology of the doped and undoped block copolymer aggregates. We show that

  4. Block copolymer self-assembly : homopolymer additives and multiple length scales

    NARCIS (Netherlands)

    Klymko, Tetyana Romanivna

    2008-01-01

    This thesis is devoted to a theoretical study of self-assembly in specific block-copolymer systems. The ability of block copolymer-based systems to organize at the nanoscale level depends on several parameters, such as volume fraction of the different components, their molar masses and the strength

  5. Dilute gels with exceptional rigidity from self-assembling silk-collagen-like block copolymers

    NARCIS (Netherlands)

    Martens, A.A.; Gucht, van der J.; Eggink, G.; Wolf, de F.A.; Cohen Stuart, M.A.

    2009-01-01

    Rheological data on monodisperse block copolymer hydrogels are rare because the amounts produced with various methods usually are not sufficient for materials testing. By biotechnological means, expression of a block copolymer encoding gene in the yeast Pichia pastoris, we produced enough protein bl

  6. Mechanical properties of weakly segregated block copolymers : 1. Synergism on tensile properties of poly(styrene-b-n-butylmethacrylate) diblock copolymers

    NARCIS (Netherlands)

    Weidisch, R.; Michler, G.H.; Fischer, H.; Arnold, M.; Hofmann, S.; Stamm, M.

    1999-01-01

    Mechanical properties of poly(styrene-b-n-butylmethacrylate) diblock copolymers, PS-b-PBMA, with different lengths of the polystyrene block were investigated. The copolymers display a composition range where the tensile strength of the block copolymers exceeds the values of the corresponding homopol

  7. Understanding the ordering mechanisms of self-assembled nanostructures of block copolymers during zone annealing.

    Science.gov (United States)

    Cong, Zhinan; Zhang, Liangshun; Wang, Liquan; Lin, Jiaping

    2016-03-21

    A theoretical method based on dynamic version of self-consistent field theory is extended to investigate directed self-assembly behaviors of block copolymers subjected to zone annealing. The ordering mechanisms and orientation modulation of microphase-separated nanostructures of block copolymers are discussed in terms of sweep velocity, wall preference, and Flory-Huggins interaction parameter. The simulated results demonstrate that the long-range ordered nanopatterns are achieved by lowering the sweep velocity of zone annealing due to the incorporation of templated ordering of block copolymers. The surface enrichment by one of the two polymer species induces the orientation modulation of defect-free nanostructures through finely tuning the composition of block copolymers and the preference of walls. Additionally, the Flory-Huggins interaction parameters of block copolymers in the distinct regions are main factors to design the zone annealing process for creating the highly ordered nanostructures with single orientation. PMID:27004895

  8. Phase behavior of multi-arm star-shaped polystyrene-block-poly(methyl methacrylate) copolymer

    Science.gov (United States)

    Jang, Sangshin; Moon, Hong Chul; Bae, Dusik; Kwak, Jonghen; Kim, Jin Kon

    2013-03-01

    We synthesized star-shaped polystyrene-block-poly(methyl methacrylate) copolymer (PS- b-PMMA) by utilizing α-cyclodextrin (α-CD) as a core of the star-shaped block copolymer. Eighteen hydroxyl groups on α-CD were transformed to bromine by the reaction with α-bromoisobutyryl bromide. We found that the number of bromine substituted arms per one α-CD was higher than 16, which was determined by nuclear magnetic resonance and Matrix-assisted laser desorption/ionization. We could control molecular weight of block copolymers by changing polymerization times. The block copolymers were characterized by gel permeation chromatography and nuclear magnetic resonance. Phase behaviors of these star-shaped block copolymers were investigated by small angle X-ray scattering and transmission electron microscopy.

  9. Understanding the ordering mechanisms of self-assembled nanostructures of block copolymers during zone annealing

    Science.gov (United States)

    Cong, Zhinan; Zhang, Liangshun; Wang, Liquan; Lin, Jiaping

    2016-03-01

    A theoretical method based on dynamic version of self-consistent field theory is extended to investigate directed self-assembly behaviors of block copolymers subjected to zone annealing. The ordering mechanisms and orientation modulation of microphase-separated nanostructures of block copolymers are discussed in terms of sweep velocity, wall preference, and Flory-Huggins interaction parameter. The simulated results demonstrate that the long-range ordered nanopatterns are achieved by lowering the sweep velocity of zone annealing due to the incorporation of templated ordering of block copolymers. The surface enrichment by one of the two polymer species induces the orientation modulation of defect-free nanostructures through finely tuning the composition of block copolymers and the preference of walls. Additionally, the Flory-Huggins interaction parameters of block copolymers in the distinct regions are main factors to design the zone annealing process for creating the highly ordered nanostructures with single orientation.

  10. Multibody Dissipative Particle Dynamics Study of the Composition Effect on the Morphology of Block Copolymer Thin Film%嵌段共聚物组成对薄膜形貌影响的多体耗散粒子动力学研究

    Institute of Scientific and Technical Information of China (English)

    李延春; 刘鸿; 黄旭日; 孙家锺

    2011-01-01

    利用多体耗散粒子动力学(Multibody Dissipative Particle Dynamics,Multibody DPD)方法研究了在溶剂蒸发条件下,嵌段共聚物在表面自组装形成薄膜的过程,分别考虑了两嵌段共聚物和三嵌段共聚物及不同组成对薄膜形貌的影响.模拟得到了无序状薄膜和层状薄膜,并计算了这些薄膜的序参量和薄膜厚度随时间的演化.结果表明,嵌段共聚物的组成对薄膜厚度几乎没有影响,当某种组分的链段很短时,只能形成序参量较小的无序薄膜,相反,则可以得到序参量较大的层状薄膜.%We use multibody dissipative particle dynamics method to investigate the thin film formed by self-assembly of block copolymer on attractive surface under evaporation condition. We consider the composition effect on the morphology of diblock and triblock copolymer thin film. We obtain disorder and lamellar morphology and give the time evolution of the order parameter and the film thickness. The results reveal that the composition of block copolymer effects on the order parameter rather than the film thickness. If one of the compositions is shorter, it is easily to form disorder morphology with lower order parameter. On the other hand, it is easily to form lamellar morphology with higher order parameter.

  11. Nanowire polarizers by guided self-assembly of block copolymers

    Science.gov (United States)

    Roberts, Philip M. S.; Baum, Alexandra; Karamath, James; Evans, Allan; Shibata, Satoshi; Walton, Harry

    2014-01-01

    Wire-grid polarizers (WGPs) are currently limited by their wafer-scale manufacturing methods to sizes of approximately 12 to 18 in. For large-size displays, a new method for the production of large-area WGPs is required. Large-area WGPs were simulated using the finite-difference-time-domain method, and a scaleable method for their production based on a block copolymer (BCP)-nanostructured template was implemented. The nanostructured template is globally aligned through the use of a cylinder-forming liquid crystal (LC) diblock copolymer, which is first aligned on a rubbed polyimide substrate. A surface-relief template is produced using the differential dry etch rates of the cylinder-forming component and LC polymer matrix component of the BCP. The template is metalized to produce a WGP. Polarizers of arbitrary size with polarization efficiency up to 0.6 have been made in close agreement with calculated values for idealized structures. The choice of the cylinder-forming polymer is critical to the degree of alignment of the template, and the thermal stability of the LC polymer matrix is critical to the stability of the template during etching.

  12. Ultrathin and Micellar Block Copolymer Films for Nanopatterning

    Science.gov (United States)

    Möller, Martin

    1998-03-01

    The formation of A-B functionalized surfaces, where nanometer sized A and B patches are distinguished for their different physical and chemical properties, represent a rather virgin field of research. We will present a technology for generating nanosized chemical heterogeneous surfaces by combination of self-organization of metal particle containing diblock copolymer micelles and conventional semiconductor etching techniques. Polystrene-block-poly(2-vinylpyridine) diblock copolymers form reverse micelles in toluene, i.e., a core of P2VP is protected by a shell of PS. Such nanocompartments are used for generating metal or semiconductor particles of equal size in each single micelle in solution. The micelle stabilized particles can be cast to mono micellar films, forming quasi hexagonal arranged lattices. The particle to particle distance (10 to 200nm) is controlled by the polymer shell and the particles size (1 to 20nm) by the micellar compartment. After film formation the polymer shell can be removed comp letely by using an oxygen plasma technique resulting in the deposition of the naked clusters on different substrates without destroying the former particle organization. These highly regular metal or semiconducting nanopatches can cover macroscopic areas (5cm x 5cm). The metal patterns are used for binding single makromolecules or as masks for nanolithography. Epitaxially grown semiconductors like GaAs, InGaAs or InP have been structured by islands or holes and their quantisized band structure has been in vestigated.

  13. Novel fluorescent amphiphilic block copolymers: photophysics behavior and interactions with DNA

    Directory of Open Access Journals (Sweden)

    2007-06-01

    Full Text Available In this study, novel amphiphilic fluorescent copolymers poly(N-vinylpyrrolidone-b-poly(N-methacryloyl-N'-(α-naphthylthiourea (PVP-b-PNT were synthesized via ATRP with poly(N-vinylpyrrolidone-Cl as macroinitiator and N-methacryloyl-N'-α-naphthylthiourea (NT as hydrophobic segment. PVP-b-PNT copolymers were characterized by 1H NMR, GPC-MALLS and fluorescence measurements. The aggregation behavior of PVP-b-PNT in water was investigated by transmission electron microscope (TEM and dynamic light scattering (DLS measurement. The photophysics behavior of PVP-b-PNT showed that block copolymer formed strong excimer. The interaction of DNA with the block copolymer made the excimer of block copolymer quench. The cytotoxicity result of PVP-b-PNT in cell culture in vitro indicated that this copolymer PVP-b-PNT had good biocompatibility.

  14. Synthesis and gas permeability of block copolymers composed of poly(styrene-co-acrylonitrile) and polystyrene blocks

    Czech Academy of Sciences Publication Activity Database

    Lokaj, Jan; Brožová, Libuše; Holler, Petr; Pientka, Zbyněk

    2002-01-01

    Roč. 67, č. 2 (2002), s. 267-278. ISSN 0010-0765 R&D Projects: GA ČR GA203/99/0572 Institutional research plan: CEZ:AV0Z4050913 Keywords : azeotropic styrene- acrylonitrile copolymers * block copolymers * nitroxide-mediated copolymerization Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.848, year: 2002

  15. Negative-tone block copolymer lithography by in situ surface chemical modification.

    Science.gov (United States)

    Kim, Bong Hoon; Byeon, Kyeong-Jae; Kim, Ju Young; Kim, Jinseung; Jin, Hyeong Min; Cho, Joong-Yeon; Jeong, Seong-Jun; Shin, Jonghwa; Lee, Heon; Kim, Sang Ouk

    2014-10-29

    Negative-tone block copolymer (BCP) lithography based on in situ surface chemical modification is introduced as a highly efficient, versatile self-assembled nanopatterning. BCP blends films consisting of end-functionalized low molecular weight poly(styrene-ran-methyl methacrylate) and polystyrene-block-Poly(methyl methacylate) can produce surface vertical BCP nanodomains on various substrates without prior surface chemical treatment. Simple oxygen plasma treatment is employed to activate surface functional group formation at various substrates, where the end-functionalized polymers can be covalently bonded during the thermal annealing of BCP thin films. The covalently bonded brush layer mediates neutral interfacial condition for vertical BCP nanodomain alignment. This straightforward approach for high aspect ratio, vertical self-assembled nanodomain formation facilitates single step, site-specific BCP nanopatterning widely useful for various substrates. Moreover, this approach is compatible with directed self-assembly approaches to produce device oriented laterally ordered nanopatterns. PMID:24912807

  16. Aligned nanowires and nanodots by directed block copolymer assembly

    Energy Technology Data Exchange (ETDEWEB)

    Xiao Shuaigang; Yang Xiaomin; Lee, Kim Y; Ver der Veerdonk, Rene J M; Kuo, David [Seagate Technology, 47010 Kato Road, Fremont, CA 94538 (United States); Russell, Thomas P, E-mail: shuaigang.xiao@seagate.com [Department of Polymer Science and Engineering, University of Massachusetts, 120 Governors Drive, Amherst, MA 01003 (United States)

    2011-07-29

    The directed self-assembly of block copolymers (BCPs) is a promising route to generate highly ordered arrays of sub-10 nm features. Ultradense arrays of a monolayer of spherical microdomains or cylindrical microdomains oriented parallel to the surface have been produced where the lateral ordering is guided by surface patterning and the lattice defined by the patterning can be commensurate or incommensurate with the natural period of the BCP. Commensurability between the two can be used to elegantly manipulate the lateral ordering and orientation of the BCP microdomains so as to form well-aligned arrays of 1D nanowires or 2D addressable nanodots. No modification of the substrate surface, aside from the patterning, was used, making the influence of lattice mismatch and pattern amplification on the size, shape and pitch of the BCP microdomains more transparent. A skew angle between incommensurate lattices, defining a stretching or compression of the BCP chains to compensate for the lattice mismatch, is presented.

  17. Aligned nanowires and nanodots by directed block copolymer assembly

    International Nuclear Information System (INIS)

    The directed self-assembly of block copolymers (BCPs) is a promising route to generate highly ordered arrays of sub-10 nm features. Ultradense arrays of a monolayer of spherical microdomains or cylindrical microdomains oriented parallel to the surface have been produced where the lateral ordering is guided by surface patterning and the lattice defined by the patterning can be commensurate or incommensurate with the natural period of the BCP. Commensurability between the two can be used to elegantly manipulate the lateral ordering and orientation of the BCP microdomains so as to form well-aligned arrays of 1D nanowires or 2D addressable nanodots. No modification of the substrate surface, aside from the patterning, was used, making the influence of lattice mismatch and pattern amplification on the size, shape and pitch of the BCP microdomains more transparent. A skew angle between incommensurate lattices, defining a stretching or compression of the BCP chains to compensate for the lattice mismatch, is presented.

  18. Microstructural organization of polydimethylsiloxane based polyurethane block copolymers

    Science.gov (United States)

    Hernandez, Rebeca; Weksler, Jadwiga; Padsalgikar, Ajay; Runt, James

    2007-03-01

    Microphase separation was investigated for polyurethane block copolymers synthesized from MDI and 1,4 butanediol as the hard segments, and poly(hexamethyleneoxide) (MW ˜ 700) and bis(6-hydroxyethoxypropyl) poly(dimethylsiloxane) as soft segments (MW ˜ 1000). The neat PDMS-based diol presents two segmental relaxations corresponding to the principle siloxane repeat unit and to the hydroxyethoxypropyl end group segments, respectively. When incorporated in the polyurethane, the siloxane units form a phase without intermixing with hard segments and the polyether end group segments are mixed with the second macrodiol and some short hard segment sequences. The microdomain morphology was characterized by atomic force microscopy and small-angle X-ray scattering, and the scattering data were analyzed using an approach based on a modified core-shell model. The model includes core hard segment particles (MDI-BDO), surrounded by a mixed polyether shell (PHMO and hydroxyethoxypropyl end group segments), and a matrix composed of the siloxane units.

  19. Ultraporous films with uniform nanochannels by block copolymer micelles assembly

    KAUST Repository

    Nunes, Suzana Pereira

    2010-10-12

    Films with high pore density and regularity that are easy to manufacture by conventional large-scale technology are key components aimed for fabrication of new generations of magnetic arrays for storage media, medical scaffolds, and artificial membranes. However, potential manufacture strategies like the self-assembly of block copolymers, which lead to amazing regular patterns, could be hardly reproduced up to now using commercially feasible methods. Here we report a unique production method of nanoporous films based on the self-assembly of copper(II) ion-polystyrene-b-poly(4-vinylpyridine) complexes and nonsolvent induced phase separation. Extremely high pore densities and uniformity were achieved. Water fluxes of 890 L m-2 h-1 bar-1 were obtained, which are at least 1 order of magnitude higher than those of commercially available membranes with comparable pore size. The pores are also stimuli (pH)-responsive. © 2010 American Chemical Society.

  20. Effects of stiffness and polydispersity on the phase behaviour of block copolymers

    OpenAIRE

    Jager, Pieter Menno

    2006-01-01

    In this thesis the phase behaviour of melts of chain-like molecules, also known as polymers, is studied. Polymers are built from monomers. These monomers are connected consecutively to form chains. If all monomers are of the same kind the chain is called a homopolymer. The polymers studied in this thesis are block copolymers. In a block copolymer different kinds of homopolymers or so-called blocks are connected. For example a diblock copolymer consists of two different kinds of blocks A and B...

  1. Poly(lactide)-block-poly([epsilon]-caprolactone-co-[epsilon]-decalactone)-block-poly(lactide) copolymer elastomers

    Energy Technology Data Exchange (ETDEWEB)

    Schneiderman, Deborah K.; Hill, Erin M.; Martello, Mark T.; Hillmyer, Marc A. (UMM)

    2015-08-28

    Batch ring opening transesterification copolymerization of ε-caprolactone and ε-decalactone was used to generate statistical copolymers over a wide range of compositions and molar masses. Reactivity ratios determined for this monomer pair, rCL = 5.9 and rDL = 0.03, reveal ε-caprolactone is added preferentially regardless of the propagating chain end. Relative to poly(ε-caprolactone) the crystallinity and melting point of these statistical copolymers were depressed by the addition of ε-decalactone; copolymers containing greater than 31 mol% (46 wt%) ε-decalactone were amorphous. Poly(lactide)-block-poly(ε-caprolactone-co-ε-decalactone)-block-poly(lactide) triblock polymers were also prepared and used to explore the influence of midblock composition on the temperature dependent Flory-Huggins interaction parameter (χ). In addition, uniaxial extension tests were used to determine the effects of midblock composition, poly(lactide) content, and molar mass on the mechanical properties of these new elastomeric triblocks.

  2. Amine-containing block copolymers: long-term adhesion promoters and corrosion resistant coatings

    Energy Technology Data Exchange (ETDEWEB)

    Small, J.H.; Saunders, R.S.; Kent, M.S.

    1996-07-01

    Arylamine-containing diblock copolymers were prepared via ring- opening metathesis polymerization (ROMP) to afford well-defined phase- separated materials. Alteration of the functionaity in a block, as well as the size of the blocks, allowed for the synthesis of self- assembled monolayers on a copper surface. The arylamine-containing block exhibited a strong binding affinity for the copper surface as seen by neutron reflectivity experiments. In addition, neutron reflectivity data verifies the self-assembly of block copolymer monolayers normal to the copper surface. Block copolymers prepared in this manner allow for the preparation of a wide range of adhesives and corrosion resistant materials. The use of ring-opening metathesis polymerization is important because it permits the synthesis of a variety of functionalized block copolymers.

  3. Fluorosilicone multi-block copolymers tethering quaternary ammonium salt groups for antimicrobial purpose

    International Nuclear Information System (INIS)

    Highlights: • QAS-containing fluorosilicone multi-block copolymers were synthesized. • The block length of PHFBMA in the copolymers was tailored via RAFT polymerization. • Surface roughness of the copolymers decreased with the increased PHFBMA content. • A certain length of PHFBMA block enhanced C−N+ percentage on the surface. - Abstract: Symmetrically structured fluorosilicone multi-block copolymers containing poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) and poly(hexafluorobutyl methacrylate) (PHFBMA) were sequentially synthesized via reversible addition–fragmentation chain transfer polymerization, using a polydimethylsiloxane (PDMS) chain transfer agent with dithiocarbonate groups at both ends. Then, the CBABC-type block copolymers were quaternized with n-octyliodide to tether quaternary ammonium salt (QAS) groups in the PDMAEMA blocks for the antimicrobial use. The obtained fluorosilicone copolymers showed clear variations in the C-N+ composition and surface morphology on their films depending on the content of the PHFBMA blocks, which were characterized by X-ray photoelectron spectroscopy and atomic force microscopy, respectively. The results indicated that the symmetrical CBABC structure favored PDMS and QAS tethered blocks migrating to the film surface. With the mass percentage of the PHFBMA increased from 0 to 32.5%, the surface roughness of the copolymer film decreased gradually with a tendency to form a smooth surface. Owing to the surface properties, fluorosilicone multi-block copolymers containing a certain amount of PHFBMA with higher C-N+ content and relatively smooth morphology demonstrated obvious antimicrobial activity against Gram-positive bacteria, Bacillus subtilis and Gram-negative bacteria, Escherichia coli. The functionalized multi-block copolymers based on fluorosilicone and QAS groups would have potential applications in antimicrobial coatings

  4. Fluorosilicone multi-block copolymers tethering quaternary ammonium salt groups for antimicrobial purpose

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Fang; Qin, Xiaoshuai; Li, Yancai; Ren, Lixia; Zhao, Yunhui, E-mail: zhaoyunhui@tju.edu.cn; Yuan, Xiaoyan

    2015-08-30

    Highlights: • QAS-containing fluorosilicone multi-block copolymers were synthesized. • The block length of PHFBMA in the copolymers was tailored via RAFT polymerization. • Surface roughness of the copolymers decreased with the increased PHFBMA content. • A certain length of PHFBMA block enhanced C−N{sup +} percentage on the surface. - Abstract: Symmetrically structured fluorosilicone multi-block copolymers containing poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) and poly(hexafluorobutyl methacrylate) (PHFBMA) were sequentially synthesized via reversible addition–fragmentation chain transfer polymerization, using a polydimethylsiloxane (PDMS) chain transfer agent with dithiocarbonate groups at both ends. Then, the CBABC-type block copolymers were quaternized with n-octyliodide to tether quaternary ammonium salt (QAS) groups in the PDMAEMA blocks for the antimicrobial use. The obtained fluorosilicone copolymers showed clear variations in the C-N{sup +} composition and surface morphology on their films depending on the content of the PHFBMA blocks, which were characterized by X-ray photoelectron spectroscopy and atomic force microscopy, respectively. The results indicated that the symmetrical CBABC structure favored PDMS and QAS tethered blocks migrating to the film surface. With the mass percentage of the PHFBMA increased from 0 to 32.5%, the surface roughness of the copolymer film decreased gradually with a tendency to form a smooth surface. Owing to the surface properties, fluorosilicone multi-block copolymers containing a certain amount of PHFBMA with higher C-N{sup +} content and relatively smooth morphology demonstrated obvious antimicrobial activity against Gram-positive bacteria, Bacillus subtilis and Gram-negative bacteria, Escherichia coli. The functionalized multi-block copolymers based on fluorosilicone and QAS groups would have potential applications in antimicrobial coatings.

  5. Investigating self-assembly and metal nanoclusters in aqueous di-block copolymers solutions

    CERN Document Server

    Lo Celso, F; Triolo, R; Triolo, A; Strunz, P; Bronstein, L; Zwanziger, J; Lin, J S

    2002-01-01

    Self-assembling properties of di-block copolymers/ surfactant hybrids in aqueous solution can be exploited to obtain metal nanoparticles stable dispersion. Results will be presented here for polystyrene-block-poly(ethylene oxide) solutions. A SANS structural investigation has been performed over different molecular weights of both hydrophilic and hydrophobic block, by varying temperature and concentration of the copolymer. A SAXS characterization of micellar systems containing Pt nanoparticles is reported. (orig.)

  6. How to Place Block Copolymer Molecules at the Interface of a Binary Blend

    Science.gov (United States)

    Chen, Zhong-Ren; Xu, Yuci; Zhong, Shuo

    2015-03-01

    Block copolymers have been used to reduce the domain size of immiscible polymer blends and thus improve the mechanical and other properties. The effectiveness of this method, however, depends on the percentage of these polymeric surfactants residing at the interface of the blend. In fact, theoretical as well as experimental work indicate that a large percentage of block copolymers form micelles in the bulk of one or both of the component polymers. These micelles may serve as weak spots initiating crack propagation. Previous work have been focused on the design of molecular architecture and synthesis of new block copolymers to address this problem. In this presentation, a simple mixing strategy is applied to make each block copolymer molecule stay at the interface. As one example, when this strategy is used to mix natural rubber (NR) with butadiene rubber (BR), a small amount of low molecular weight block copolymer (LIR) improves both processing characteristics such as melt viscosity and mechanical properties of cured samples, such as crack resistance. AFM micrographs show the much smaller domain size; and an original real-time monitoring system reveals the lowest crack growth rate. Using a model A/B/A-B binary blend, we have witnessed by microscopy that all block copolymer molecules form micelles at the first mixing step, and all of these micelles are disappeared and all block copolymer molecules stay at the interface after the second mixing step.

  7. Fabrication of Bioactive Surfaces by Functionalization of Electroactive and Surface-Active Block Copolymers

    Directory of Open Access Journals (Sweden)

    Omotunde Olubi

    2014-08-01

    Full Text Available Biofunctional block copolymers are becoming increasingly attractive materials as active components in biosensors and other nanoscale electronic devices. We have described two different classes of block copolymers with biofuctional properties. Biofunctionality for block copolymers is achieved through functionalization with appropriate biospecific ligands. We have synthesized block copolymers of electroactive poly(3-decylthiophene and 2-hydroxyethyl methacrylate by atom transfer radical polymerization. The block copolymers were functionalized with the dinitrophenyl (DNP groups, which are capable of binding to Immunoglobulin E (IgE on cell surfaces. The block copolymers were shown to be redox active. Additionally, the triblock copolymer of α, ω-bi-biotin (poly(ethylene oxide-b-poly (styrene-b-poly(ethylene oxide was also synthesized to study their capacity to bind fluorescently tagged avidin. The surface-active property of the poly(ethylene oxide block improved the availability of the biotin functional groups on the polymer surfaces. Fluorescence microscopy observations confirm the specific binding of biotin with avidin.

  8. Surface Modification of Block Copolymer Through Sulfur Containing Plasma Treatment.

    Science.gov (United States)

    Choi, Sang Wook; Shin, Jae Hee; Jeon, Min Hwan; Mun, Jeong Ho; Kim, Sang Ouk; Yeom, Geun Young; Kim, Kyong Nam

    2015-10-01

    Some of the important issues of block copolymer (BCP) as an application to the potential low cost next generation lithography are thermal stability and deformation during pattern transfer process in addition to defect density, line edge/width roughness, etc. In this study, sulfur containing plasma treatment was used to modify the BCP and the effects of the plasma on the properties of plasma treated BCP were investigated. The polystyrene hole pattern obtained from polystyrene polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) was initially degraded when the polystyrene hole was annealed at 190 °C for 15 min. However, when the hole pattern was treated using sulfur containing plasmas using H2S or SF6 up to 2 min, possibly due to the sulfurization of the polystyrene hole surface, no change in the hole pattern was observed after the annealing even though there is a slight change in hole shapes during the plasma treatment. The optimized plasma treated polystyrene pattern showed the superior characteristics as the mask layer by showing better thermal stability, higher chemical inertness, and higher etch selectivity during plasma etching. PMID:26726468

  9. Bicontinuous ceramics with high surface area from block copolymer templates.

    Science.gov (United States)

    Hsueh, Han-Yu; Ho, Rong-Ming

    2012-06-01

    Mesoporous polymers with gyroid nanochannels can be fabricated from the self-assembly of degradable block copolymer, polystyrene-b-poly(L-lactide) (PS-PLLA), followed by hydrolysis of PLLA block. Well-defined polymer/ceramic nanohybrid materials with inorganic gyroid nanostructures in a PS matrix can be obtained by using the mesoporous PS as a template for sol-gel reaction. Titanium tetraisopropoxide (TTIP) is used as a precursor to give a model system for the fabrication of metal oxide nanostructures from reactive transition metal alkoxides. By controlling the rates of capillary-driven pore filling and sol-gel reaction, the templated synthesis can be well-developed. Also, by taking advantage of calcination, bicontinuous TiO(2) with controlled crystalline phase (i.e., anatase phase) can be fabricated after removal of the PS template and crystallization of TiO(2) by calcination leading to high photocatalytic efficiency. This new approach provides an easy way to fabricate high-surface-area and high-porosity ceramics with self-supporting structure and controlled crystalline phase for practical applications. As a result, a platform technology to fabricate precisely controlled polymer/ceramic nanohybrids and mesoporous ceramic materials can be established. PMID:22530553

  10. Flexible Battery Cathodes Enabled by Conductive Block Copolymers

    Science.gov (United States)

    Lutkenhaus, Jodie; Verduzco, Rafael; An, Hyosung; Lin, Yen-Hao; Lutkenhaus Laboratory Collaboration; Verduzco Laboratory Collaboration

    2015-03-01

    Alone, or as part of hybrid electrodes, conductive polymers are poised to play an integral role in the new and growing field of flexible or ``plastic'' power. Here we demonstrate that even small amounts of a poly(3-hexylthiophene)-block-poly(ethylene oxide) (P3HT-b-PEO) block copolymer, acting as an ion and electron conductor, can bring about significant improvements in energy storage and mechanical flexibility for V2O5 hybrid cathodes for Li-ion batteries. By following this approach, traditional inert polymer binders and carbon black additives are not needed. V2O5 alone has a high theoretical capacity that is limited in practical application by low conductivity. Further, V2O5 alone is brittle and breaks upon repeated flexure. P3HT-b-PEO serves to address both these issues. This presentation will cover how these hybrid electrodes are formed and the resulting physicochemical properties that lead to its enhanced flexibility and energy storage.

  11. Controlling sub-microdomain structure in microphase-ordered block copolymers and their nanocomposites

    Science.gov (United States)

    Bowman, Michelle Kathleen

    Block copolymers exhibit a wealth of morphologies that continue to find ubiquitous use in a diverse variety of mature and emergent (nano)technologies, such as photonic crystals, integrated circuits, pharmaceutical encapsulents, fuel cells and separation membranes. While numerous studies have explored the effects of molecular confinement on such copolymers, relatively few have examined the sub-microdomain structure that develops upon modification of copolymer molecular architecture or physical incorporation of nanoscale objects. This work will address two relevant topics in this vein: (i) bidisperse brushes formed by single block copolymer molecules and (ii) copolymer nanocomposites formed by addition of molecular or nanoscale additives. In the first case, an isomorphic series of asymmetric poly(styrene-b -isoprene-b-styrene) (S1IS2) triblock copolymers of systematically varied chain length has been synthesized from a parent SI diblock copolymer. Small-angle x-ray scattering, coupled with dynamic rheology and self-consistent field theory (SCFT), reveals that the progressively grown S2 block initially resides in the I-rich matrix and effectively reduces the copolymer incompatibility until a critical length is reached. At this length, the S2 block co-locates with the S1 block so that the two blocks generate a bidisperse brush (insofar as the S1 and S2 lengths differ). This single-molecule analog to binary block copolymer blends affords unique opportunities for materials design at sub-microdomain length scales and provides insight into the transition from diblock to triblock copolymer (and thermoplastic elastomeric nature). In the second case, I explore the distribution of molecular and nanoscale additives in microphase-ordered block copolymers and demonstrate via SCFT that an interfacial excess, which depends strongly on additive concentration, selectivity and relative size, develops. These predictions are in agreement with experimental findings. Moreover, using a

  12. High Aspect Ratio Sub-15 nm Silicon Trenches From Block Copolymer Templates

    Science.gov (United States)

    Gu, Xiaodan; Liu, Zuwei; Gunkel, Ilja; Olynick, Deirdre; Russell, Thomas; University of Massachusetts Amherst Collaboration; Oxford Instrument Collaboration; Lawrence Berkeley National Lab Collaboration

    2013-03-01

    High-aspect-ratio sub-15 nm silicon trenches are fabricated directly from plasma etching of a block copolymer (BCP) mask. Polystyrene-b-poly(2-vinyl pyridine) (PS-b-P2VP) 40k-b-18k was spin coated and solvent annealed to form cylindrical structures parallel to the silicon substrate. The BCP thin film was reconstructed by immersion in ethanol and then subjected to an oxygen and argon reactive ion etching to fabricate the polymer mask. A low temperature ion coupled plasma with sulfur hexafluoride and oxygen was used to pattern transfer block copolymer structure to silicon with high selectivity (8:1) and fidelity. The silicon pattern was characterized by scanning electron microscopy and grazing incidence x-ray scattering. We also demonstrated fabrication of silicon nano-holes using polystyrene-b-polyethylene oxide (PS-b-PEO) using same methodology described above for PS-b-P2VP. Finally, we show such silicon nano-strucutre serves as excellent nano-imprint master template to pattern various functional materials like poly 3-hexylthiophene (P3HT).

  13. Enhanced Lateral Ordering in Cylinder Forming PS-b-PMMA Block Copolymers Exploiting the Entrapped Solvent.

    Science.gov (United States)

    Seguini, Gabriele; Zanenga, Fabio; Giammaria, Tommaso J; Ceresoli, Monica; Sparnacci, Katia; Antonioli, Diego; Gianotti, Valentina; Laus, Michele; Perego, Michele

    2016-03-30

    The self-assembly of block copolymer (BCP) thin films produces dense and ordered nanostructures. Their exploitation as templates for nanolithography requires the capability to control the lateral order of the nanodomains. Among a multiplicity of polymers, the widely studied all-organic polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) BCP can easily form nanodomains perpendicularly oriented with respect to the substrate, since the weakly unbalanced surface interactions are effectively neutralized by grafting to the substrate an appropriate poly(styrene-random-methyl methacrylate) P(S-r-MMA) random copolymer (RCP). This benefit along with the selective etching of the PMMA component and the chemical similarity with the standard photoresist materials deserved for PS-b-PMMA the role of BCP of choice for the technological implementation in nanolithography. This work demonstrates that the synergic effect of thermal annealing with the initial solvent naturally trapped in the basic RCP + BCP system after the deposition process can be exploited to enhance the lateral order. The solvent content embedded in the total RCP + BCP system can be tuned by changing the molecular weight and thus the thickness of the grafted RCP brush layer, without introducing external reservoirs or dedicated setup and/or systems. The appropriate supply of solvent supports a grain coarsening kinetics following a power law with a 1/3 growth exponent for standing hexagonally ordered cylinders. PMID:26959626

  14. Bottlebrush Copolymer Morphology Transition: Influence of Side Chain Length and Block Volume Fraction

    Science.gov (United States)

    Gai, Yue; Song, Dong-Po; Watkins, James

    Brush block copolymers synthesized via living ring-opening metathesis polymerization (ROMP) offer unique advantages as templates for functional hybrid materials. Unlike linear block copolymer, the bottlebrush polymer phase transition not only depends on volume fractions of the two blocks but also on side chain length. Here we report the morphology transitions of PS-b-PEO bottlebrush copolymer (BBCP) as a function of PEO side chain length and block volume fraction. For the BBCPs with similar side chain lengths, highly ordered lamellar morphologies were observed with PEO volume fractions in a wide range from 32 vol% to 72 vol%, which is significantly different from that of traditional linear block copolymers. This study will lay the groundwork for nanostructure fabrications using the BBCPs and provides new insights into the phase behavior of the new type of materials. This work was supported by NSF center for Hierarchical Manufacturing at the University of Massachusetts, Amherst.

  15. Phase behavior of miscible block copolymer blends and baraplastic property

    International Nuclear Information System (INIS)

    The phase behavior of the multi-component polymer systems such as blends and block copolymers (BCPs) has been studied extensively, as it determines the chemical and physical properties of the polymeric materials in practical applications. Above all, polymer baroplasticity is a desirable property for the recycling and regenerating industries, since it allows the polymers to flow at relatively mild pressure. Particularly, the compressibility issue on the enhanced miscibility with pressure has been an attractive topic, because an ordered state of the baroplastic BCPs becomes a phase-mixed state (or disordered phase) between the two dissimilar blocks upon pressurizing. This is in contrast to the incompressibility that was dictated by the enthalpic effect arising from the increased unfavorable contacts between the two blocks by increasing pressure. The phase behaviors of BCP blends composed of the weakly interacting (with no specific interaction) polystyrene-b-poly(n-butyl methacrylate) (PS-b-PnBMA) and deuterated polystyreneb- poly-(n-hexyl methacrylate) (dPS-b-PnHMA) were investigated by Small-Angle Neutron Scattering(SANS) and Depolarized Light Scattering (DPLS) measurements. Interestingly, pressure dependence of various phase transitions for the miscible BCP blends was significantly changed, in which the blends consist of a PS-b-PnBMA and a deuterated dPS-b-PnHMA. To elucidate the origin and difference in baroplasticity of weakly interacting BCP blends, the pressure dependence of transition temperatures was evaluated using enthalpic and volumetric changes at phase transitions. We also demonstrate that the entropic compressibility for the miscible BCP blends is a baroplastic indicator, which was characterized by the negative volume change on mixing (ΔVmix) at transitions.

  16. Self-assembly of novel amphiphilic block-gradient copolymers of styrene and acrylic acid

    Czech Academy of Sciences Publication Activity Database

    Štěpánek, Petr; Černochová, Zulfiya; Borisova, O.; Billon, L.; Borisov, O.

    Český Krumlov, 2015. s. 34. [Discussion workshop on ( bio )Macromolecular Ionic Systems. 10.05.2015-14.05.2015, Český Krumlov] R&D Projects: GA MŠk(CZ) LH14079 Institutional support: RVO:61389013 Keywords : block copolymers * gradient copolymers * light scattering Subject RIV: CD - Macromolecular Chemistry

  17. Synthesis nad properties of amphiphilic block copolymers containing poly 5-vinyltetrazoline or methyl-4-vinylpyridinium iodide

    Czech Academy of Sciences Publication Activity Database

    Gromadzki, D.; Janata, Miroslav; Lokaj, Jan; Štěpánek, Petr

    Arcachon: European Science Foundation Collaborative Research, 2005. P2. [Self-Assembled Structures of Amphiphilic Ionic Copolymers in Solutions and Interfaces. 11.5.2005-14.5.2005, Arcachon] Institutional research plan: CEZ:AV0Z40500505 Keywords : amphiphilic block copolymers Subject RIV: CD - Macromolecular Chemistry

  18. Novel fluorinated block copolymer architectures fuelled by atom transfer radical polymerization

    DEFF Research Database (Denmark)

    Jankova, Katja; Hvilsted, Søren

    2005-01-01

    Block copolymers based on poly(pentafluorostyrene), PFS, in various numbers and of different lengths, and polystyrene are prepared by atom transfer radical polymerization (ATRP). Di- and triblock copolymers with varying amounts of PFS were synthesized employing either I phenylethylbromide or 1,4-...

  19. Synthesis and Characterization of Stimuli Responsive Block Copolymers, Self-Assembly Behavior and Applications

    Energy Technology Data Exchange (ETDEWEB)

    Michael Duane Determan

    2005-12-17

    The central theme of this thesis work is to develop new block copolymer materials for biomedical applications. While there are many reports of stimuli-responsive amphiphilic [19-21] and crosslinked hydrogel materials [22], the development of an in situ gel forming, pH responsive pentablock copolymer is a novel contribution to the field, Figure 1.1 is a sketch of an ABCBA pentablock copolymer. The A blocks are cationic tertiary amine methacrylates blocked to a central Pluronic F127 triblock copolymer. In addition to the prerequisite synthetic and macromolecular characterization of these new materials, the self-assembled supramolecular structures formed by the pentablock were experimentally evaluated. This synthesis and characterization process serves to elucidate the important structure property relationships of these novel materials, The pH and temperature responsive behavior of the pentablock copolymer were explored especially with consideration towards injectable drug delivery applications. Future synthesis work will focus on enhancing and tuning the cell specific targeting of DNA/pentablock copolymer polyplexes. The specific goals of this research are: (1) Develop a synthetic route for gel forming pentablock block copolymers with pH and temperature sensitive properties. Synthesis of these novel copolymers is accomplished with ATRP, yielding low polydispersity and control of the block copolymer architecture. Well defined macromolecular characteristics are required to tailor the phase behavior of these materials. (2) Characterize relationship between the size and shape of pentablock copolymer micelles and gel structure and the pH and temperature of the copolymer solutions with SAXS, SANS and CryoTEM. (3) Evaluate the temperature and pH induced phase separation and macroscopic self-assembly phenomenon of the pentablock copolymer. (4) Utilize the knowledge gained from first three goals to design and formulate drug delivery formulations based on the multi

  20. Perpendicular Orientation of Nanodomains on Versatile Substrates through Self-Neutralization Induced by Star-Shaped Block Copolymers

    Science.gov (United States)

    Kim, Mooseong; Jang, Sangshin; Lee, Kyu Seong; Moon, Hong Chul; Kwak, Jongheon; Park, Jicheol; Jeon, Gumhye; Kim, Jin Kon

    A novel self-neutralization concept is introduced by designing molecular architecture of a block copolymer. Star-shaped 18 arm poly(methyl methacrylate)-block-polystyrene copolymers ((PMMA-b-PS)18) exhibiting lamellar and PMMA cylindrical nanodomains are synthesized. When a thin film of (PMMA-b-PS)18 is spin-coated on a substrate, vertically aligned lamellar and cylindrical nanodomains are obtained without any pre- or post-treatment, although thermal annealing for a short time (less than 30 min) is required to improve the spatial array of vertically aligned nanodomains. This result is attributed to the star-shaped molecular architecture that overcomes the difference in the surface affinity between PS and PMMA chains. Moreover, vertical orientations are observed on versatile substrates, for instance, semiconductor (Si, SiOx), metal (Au), PS or PMMA-brushed substrate, and a flexible polymer sheet of polyethylene naphthalate.

  1. Fluorosilicone multi-block copolymers tethering quaternary ammonium salt groups for antimicrobial purpose

    Science.gov (United States)

    Zhou, Fang; Qin, Xiaoshuai; Li, Yancai; Ren, Lixia; Zhao, Yunhui; Yuan, Xiaoyan

    2015-08-01

    Symmetrically structured fluorosilicone multi-block copolymers containing poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) and poly(hexafluorobutyl methacrylate) (PHFBMA) were sequentially synthesized via reversible addition-fragmentation chain transfer polymerization, using a polydimethylsiloxane (PDMS) chain transfer agent with dithiocarbonate groups at both ends. Then, the CBABC-type block copolymers were quaternized with n-octyliodide to tether quaternary ammonium salt (QAS) groups in the PDMAEMA blocks for the antimicrobial use. The obtained fluorosilicone copolymers showed clear variations in the C-N+ composition and surface morphology on their films depending on the content of the PHFBMA blocks, which were characterized by X-ray photoelectron spectroscopy and atomic force microscopy, respectively. The results indicated that the symmetrical CBABC structure favored PDMS and QAS tethered blocks migrating to the film surface. With the mass percentage of the PHFBMA increased from 0 to 32.5%, the surface roughness of the copolymer film decreased gradually with a tendency to form a smooth surface. Owing to the surface properties, fluorosilicone multi-block copolymers containing a certain amount of PHFBMA with higher C-N+ content and relatively smooth morphology demonstrated obvious antimicrobial activity against Gram-positive bacteria, Bacillus subtilis and Gram-negative bacteria, Escherichia coli. The functionalized multi-block copolymers based on fluorosilicone and QAS groups would have potential applications in antimicrobial coatings.

  2. STUDY ON STYRENE-BUTADIENE BLOCK COPOLYMER FOR THE MODIFICATION OF TIRE TREAD

    Institute of Scientific and Technical Information of China (English)

    WANG Yan; CHEN Weijie; MU Ruifeng; WANG Yongwei; YU Fengnian; LIU Qing

    1996-01-01

    This paper mainly deals with the design and synthesis of a novel styrene-butadiene block copolymer. When this copolymer is used in the tread portion of tyres, it can improve wet skid resistance and reduce rolling resistance without sacrificing its general physicalmechanical properties. The visco-elastic curve of tire tread using the novel copolymer as its rubber portion was showed. Reactivity ratios for two monomers in the polymerizing system were calculated. The diagrams of differential, integral and finite difference calculi throughout the whole molecular chain were presented. The influence of the micro- and macro-structure of the copolymer chain on wet skid resistance and rolling resistance was discussed.

  3. Phase Behavior of Star-shaped polystyrene-block-poly(methyl methacrylate) Copolymers

    Science.gov (United States)

    Jang, Sangshin; Moon, Hongchul; Lee, Youngmin; Kim, Jin Kon

    2012-02-01

    Star-shaped polystyrene-block-poly(methyl methacrylate) copolymer (PS-b-PMMA) was synthesized by utilizing α-cyclodextrin (α-CD) as a junction point of the star-shaped block copolymer. Eighteen hydroxyl groups on α-CD were substituted with bromine by the reaction with α-bromoisobutyryl bromide for atom transfer radical polymerization. We found that the number of bromine substituted arms per one α-CD was higher than 16 measured by nuclear magnetic resonance and Matrix-assisted laser desorption/ionization. We could control molecular weight of this unusual kind of block copolymer depending on polymerization times. Those polymers were characterized by gel permeation chromatography and nuclear magnetic resonance. Phase behavior of these star-shaped block copolymers were investigated.

  4. Self-assembled monolayer-modified block copolymers for chemical surface nanopatterning

    International Nuclear Information System (INIS)

    Research highlights: → Self-organizing PS-b-PMMA creates striped nanostructure scaffolds. → These striped nanostructures can be selectively metalized and modified using light. → Metalized stripes can be decorated with SAMs to create functional substrates. → Nanostructured surfaces thus prepared exhibit controlled wetting and recognition. - Abstract: Thin-film poly(styrene-block-methyl methacrylate) diblock copolymer (PS-b-PMMA) is used to create chemically patterned surfaces via metal deposition combined with self-assembled monolayers (SAMs) and UV exposure. We use this method to produce surfaces that are chemically striped on the scale of a few tens of nanometers. Atomic force and transmission electron microscopies are used to verify the spatially localized organization of materials, and contact angle measurements confirm the chemical tunability of these scaffolds. These surfaces may be used for arraying nanoscale objects, such as nanoparticles or biological species, or for electronic, magnetic memory or photovoltaic applications.

  5. Nanostructured Colloidal Particles by Confined Self-Assembly of Block Copolymers in Evaporative Droplets

    Science.gov (United States)

    Kim, Minsoo; Yi, Gi-Ra

    2015-06-01

    Block copolymers (BCPs) can create various morphology by self-assembly in bulk or film. Recently, using BCPs in confined geometries such as thin film (one-dimension), cylindrical template (two-dimension), or emulsion droplet (three-dimension), nanostructured BCP particles have been prepared, in which unique nanostructures of the BCP are formed via solvent annealing process and can be controlled depending on molecular weight ratio and interaction parameter of the BCPs, and droplet size. Moreover, by tuning interfacial property of the BCP particles, anisotropic particles with unique nanostructures have been prepared. Furthermore, for practical application such as drug delivery system, sensor, self-healing, metamaterial, and optoelectronic device, functional nanoparticles can be incorporated inside BCP particles. In this article, we summarize recent progress on the production of structured BCP particles and composite particles with metallic nanoparticles.

  6. Funding initiates production of tunable nano-porous block copolymer membranes

    KAUST Repository

    Peinemann, Klaus-Viktor

    2013-06-01

    Researchers in Saudi Arabia at King Abdullah University of Science & Technology have created a membrane comprising a thin layer of densely packed, highly ordered cylindrical channels with uniform pore sizes - oriented perpendicular to its surface - on top of a non-ordered sponge-like layer. It is fabricated in a fast, one-step process by combining the self-assembly of an amphiphilic block copolymer (PS- b-P4VP) with non-solvent-induced phase separation. The university\\'s "Seed Fund" has helped the researchers to start manufacturing this membrane, which is particularly suited to size-selective and charge-based separation of bio-molecules. © 2013 Elsevier Ltd.

  7. Microtome Sliced Block Copolymers and Nanoporous Polymers as Masks for Nanolithography

    DEFF Research Database (Denmark)

    Shvets, Violetta; Schulte, Lars; Ndoni, Sokol

    2014-01-01

    -linked phase are sliced with microtome and pattern is transfered from flakes to substrate by plasma etching. Experimental Section. Group of Self-organized Nanoporous Materials in Technical University of Denmark has developed series of block copolymers of Polybutadiene-b-Polydimethylsiloxane (PB-b-PDMS) of...... hexagonal pattern were transferred onto silicon wafer for plasma etching. Results and Discussion. After flakes had been removed hexagonal arrays of holes were observed on the silicon. Quality of observed structures depends on etching time. The longer etching time is the large optimal thickness of flake for...... pattern transfer. For shot times there are no structures under the thick flakes (60-120 nm thick) but thinnest flakes (25-35 nm thick) give nice hexagonal patterns on the surface. On longer times holes under thin flakes start to merge. Thicker flakes have large surface roughness and on longer times of...

  8. Complexation-tailored morphology of asymmetric block copolymer membranes

    KAUST Repository

    Madhavan, Poornima

    2013-08-14

    Hydrogen-bond formation between polystyrene-b-poly (4-vinylpyridine) (PS-b-P4VP) block copolymer (BCP) and -OH/-COOH functionalized organic molecules was used to tune morphology of asymmetric nanoporous membranes prepared by simultaneous self-assembly and nonsolvent induced phase separation. The morphologies were characterized by field emmision scanning electron microscopy (FESEM) and atomic force microscopy (AFM). Hydrogen bonds were confirmed by infrared (IR), and the results were correlated to rheology characterization. The OH-functionalized organic molecules direct the morphology into hexagonal order. COOH-functionalized molecules led to both lamellar and hexagonal structures. Micelle formation in solutions and their sizes were determined using dynamic light scattering (DLS) measurements and water fluxes of 600-3200 L/m 2·h·bar were obtained. The pore size of the plain BCP membrane was smaller than with additives. The following series of additives led to pores with hexagonal order with increasing pore size: terephthalic acid (COOH-bifunctionalized) < rutin (OH-multifunctionalized) < 9-anthracenemethanol (OH-monofunctionalized) < 3,5-dihydroxybenzyl alcohol (OH-trifunctionalized). © 2013 American Chemical Society.

  9. Biosynthesis and characterization of diblock copolymer of p(3-hydroxypropionate)-block-p(4-hydroxybutyrate) from recombinant Escherichia coli

    DEFF Research Database (Denmark)

    Tripathi, Lakshmi; Wu, Linping; Meng, Dechuan;

    2013-01-01

    Poly(4-hydroxybutyrate) (P4HB) is a highly elastic polymer, whereas poly(3-hydroxypropionate) (P3HP) is a polymer with enormous tensile strength. This study aimed to biosynthesize a block copolymer consisting of soft P4HB block with a strong P3HP block to gain unique and excellent material...... superior properties over random copolymers P(3HP-co-4HB). The block copolymers had two glass transition temperatures (Tg) and two melting temperatures (Tm). In comparison to the homopolymers P3HP and P4HB, incorporation of block microstructure resulted in the lowering of Tm, block copolymers were revealed...

  10. Enhancing ordering dynamics in solvent-annealed block-copolymer films by lithographic hard masks supports

    OpenAIRE

    Stenbock-Fermor, Anja; Knoll, Armin W.; Böker, Alexander; Tsarkova, Larisa

    2014-01-01

    We studied solvent-driven ordering dynamics of block copolymer films supported by a densely cross-linked polymer network designed as organic hard mask (HM) for lithographic fabrications. The ordering of microphase separated domains at low degrees of swelling corresponding to intermediate/strong segregation regimes was found to proceed significantly faster in films on a HM layer as compared to similar block copolymer films on silicon wafers. The ten-fold enhancement of the chain mobility was e...

  11. Synthesis and Characterization of Proton Conducting, Fluorine-Containing Block Copolymers

    OpenAIRE

    Shi, Zhi Qing

    2004-01-01

    Fuel cells are being investigated as environmental-friendly, highly efficient alternative power sources. Proton conducting membranes play a central role in proton exchange membrane fuel cells (PEMFCs), serving as both electrolyte and fuel separator. This thesis addresses the design, synthesis and characterization of novel fluorinecontaining block copolymers, and the preparation and investigation of sulfonated block copolymers as model proton exchange membranes (PEMs). Poly([vinylidene difluor...

  12. Synthesis and self-assembly of multiple thermoresponsive amphiphilic block copolymers

    OpenAIRE

    Weiß, Jan

    2011-01-01

    In the present thesis, the self-assembly of multi thermoresponsive block copolymers in dilute aqueous solution was investigated by a combination of turbidimetry, dynamic light scattering, TEM measurements, NMR as well as fluorescence spectroscopy. The successive conversion of such block copolymers from a hydrophilic into a hydrophobic state includes intermediate amphiphilic states with a variable hydrophilic-to-lipophilic balance. As a result, the self-organization is not following an all-or-...

  13. The fabrication of tunable nanoporous oxide surfaces by block copolymer lithography and atomic layer deposition

    Energy Technology Data Exchange (ETDEWEB)

    Andreozzi, A; Lamagna, L; Seguini, G; Fanciulli, M; Perego, M [Laboratorio MDM, IMM-CNR, Via C Olivetti 2, I-20864 Agrate Brianza (Italy); Schamm-Chardon, S; Castro, C, E-mail: andrea.andreozzi@mdm.imm.cnr.it [CEMES-CNRS and Universite de Toulouse, nMat group, BP 94345, F-31055 Toulouse Cedex 4 (France)

    2011-08-19

    Patterned nanoscale materials with controllable characteristic feature sizes and periodicity are of considerable interest in a wide range of fields, with various possible applications ranging from biomedical to nanoelectronic devices. Block-copolymer (BC)-based lithography is a powerful tool for the fabrication of uniform, densely spaced nanometer-scale features over large areas. Following this bottom-up approach, nanoporous polymeric films can be deposited on any type of substrate. The nanoporous periodic template can be transferred to the underlying substrate by dry anisotropic etching. Nevertheless the physical sizes of the polymeric mask represent an important limitation in the implementation of suitable lithographic protocols based on BC technology, since the diameter and the center-to-center distance of the pores cannot be varied independently in this class of materials. This problem could be overcome by combining block copolymer technology with atomic layer deposition (ALD): by means of BC-based lithography a nanoporous SiO{sub 2} template, with well-reproducible characteristic dimensions, can be fabricated and subsequently used as a backbone for the growth of perfectly conformal thin oxide films by ALD. In this work polystyrene-b-poly(methylmethacrylate) (PS-b-PMMA) BC and reactive ion etching are used to fabricate hexagonally packed 23 nm wide nanopores in a 50 nm thick SiO{sub 2} matrix. By ALD deposition of Al{sub 2}O{sub 3} thin films onto the nanoporous SiO{sub 2} templates, nanostructured Al{sub 2}O{sub 3} surfaces are obtained. By properly adjusting the thickness of the Al{sub 2}O{sub 3} film the dimension of the pores in the oxide films is progressively reduced, with nanometer precision, from the original size down to complete filling of the pores, thus providing a simple and fast strategy for the fabrication of nanoporous Al{sub 2}O{sub 3} surfaces with well-controllable feature size.

  14. The fabrication of tunable nanoporous oxide surfaces by block copolymer lithography and atomic layer deposition

    International Nuclear Information System (INIS)

    Patterned nanoscale materials with controllable characteristic feature sizes and periodicity are of considerable interest in a wide range of fields, with various possible applications ranging from biomedical to nanoelectronic devices. Block-copolymer (BC)-based lithography is a powerful tool for the fabrication of uniform, densely spaced nanometer-scale features over large areas. Following this bottom-up approach, nanoporous polymeric films can be deposited on any type of substrate. The nanoporous periodic template can be transferred to the underlying substrate by dry anisotropic etching. Nevertheless the physical sizes of the polymeric mask represent an important limitation in the implementation of suitable lithographic protocols based on BC technology, since the diameter and the center-to-center distance of the pores cannot be varied independently in this class of materials. This problem could be overcome by combining block copolymer technology with atomic layer deposition (ALD): by means of BC-based lithography a nanoporous SiO2 template, with well-reproducible characteristic dimensions, can be fabricated and subsequently used as a backbone for the growth of perfectly conformal thin oxide films by ALD. In this work polystyrene-b-poly(methylmethacrylate) (PS-b-PMMA) BC and reactive ion etching are used to fabricate hexagonally packed 23 nm wide nanopores in a 50 nm thick SiO2 matrix. By ALD deposition of Al2O3 thin films onto the nanoporous SiO2 templates, nanostructured Al2O3 surfaces are obtained. By properly adjusting the thickness of the Al2O3 film the dimension of the pores in the oxide films is progressively reduced, with nanometer precision, from the original size down to complete filling of the pores, thus providing a simple and fast strategy for the fabrication of nanoporous Al2O3 surfaces with well-controllable feature size.

  15. Ionic Liquids As Self-Assembly Guide for the Formation of Nanostructured Block Copolymer Membranes

    KAUST Repository

    Madhavan, Poornima

    2015-04-30

    Nanostructured block copolymer membranes were manufactured by water induced phase inversion, using ionic liquids (ILs) as cosolvents. The effect of ionic liquids on the morphology was investigated, by using polystyrene-b-poly(4-vinyl pyridine) (PS-b-PV4P) diblock as membrane copolymer matrix and imidazolium and pyridinium based ILs. The effect of IL concentration and chemical composition was evident with particular interaction with P4VP blocks. The order of block copolymer/ILs solutions previous to the membrane casting was confirmed by cryo scanning electron microscopy and the morphologies of the manufactured nanostructured membranes were characterized by transmission and scanning electron microscopy. Non-protic ionic liquids facilitate the formation of hexagonal nanoporous block copolymer structure, while protic ILs led to a lamella-structured membrane. The rheology of the IL/block copolymer solutions was investigated, evaluating the storage and loss moduli. Most membranes prepared with ionic liquid had higher water flux than pure block copolymer membranes without additives.

  16. Mechano-responsive hydrogels crosslinked by reactive block copolymer micelles

    Science.gov (United States)

    Xiao, Longxi

    Hydrogels are crosslinked polymeric networks that can swell in water without dissolution. Owing to their structural similarity to the native extracelluar matrices, hydrogels have been widely used in biomedical applications. Synthetic hydrogels have been designed to respond to various stimuli, but mechanical signals have not incorporated into hydrogel matrices. Because most tissues in the body are subjected to various types of mechanical forces, and cells within these tissues have sophisticated mechano-transduction machinery, this thesis is focused on developing hydrogel materials with built-in mechano-sensing mechanisms for use as tissue engineering scaffolds or drug release devices. Self-assembled block copolymer micelles (BCMs) with reactive handles were employed as the nanoscopic crosslinkers for the construction of covalently crosslinked networks. BCMs were assembled from amphiphilic diblock copolymers of poly(n-butyl acrylate) and poly(acrylic acid) partially modified with acrylate. Radical polymerization of acrylamide in the presence of micellar crosslinkers gave rise to elastomeric hydrogels whose mechanical properties can be tuned by varying the BCM composition and concentration. TEM imaging revealed that the covalently integrated BCMs underwent strain-dependent reversible deformation. A model hydrophobic drug, pyrene, loaded into the core of BCMs prior to the hydrogel formation, was dynamically released in response to externally applied mechanical forces, through force-induced reversible micelle deformation and the penetration of water molecules into the micelle core. The mechano-responsive hydrogel has been studied for tissue repair and regeneration purposes. Glycidyl methacrylate (GMA)-modified hyaluronic acid (HA) was photochemically crosslinked in the presence of dexamethasone (DEX)-loaded crosslinkable BCMs. The resultant HA gels (HAxBCM) contain covalently integrated micellar compartments with DEX being sequestered in the hydrophobic core. Compared

  17. Antimicrobial activity of poly(acrylic acid) block copolymers

    Energy Technology Data Exchange (ETDEWEB)

    Gratzl, Günther, E-mail: guenther.gratzl@jku.at [Johannes Kepler University Linz, Institute for Chemical Technology of Organic Materials, Altenberger Str. 69, 4040 Linz (Austria); Paulik, Christian [Johannes Kepler University Linz, Institute for Chemical Technology of Organic Materials, Altenberger Str. 69, 4040 Linz (Austria); Hild, Sabine [Johannes Kepler University Linz, Institute of Polymer Science, Altenberger Str. 69, 4040 Linz (Austria); Guggenbichler, Josef P.; Lackner, Maximilian [AMiSTec GmbH and Co. KG, Leitweg 13, 6345 Kössen, Tirol (Austria)

    2014-05-01

    The increasing number of antibiotic-resistant bacterial strains has developed into a major health problem. In particular, biofilms are the main reason for hospital-acquired infections and diseases. Once formed, biofilms are difficult to remove as they have specific defense mechanisms against antimicrobial agents. Antimicrobial surfaces must therefore kill or repel bacteria before they can settle to form a biofilm. In this study, we describe that poly(acrylic acid) (PAA) containing diblock copolymers can kill bacteria and prevent from biofilm formation. The PAA diblock copolymers with poly(styrene) and poly(methyl methacrylate) were synthesized via anionic polymerization of tert-butyl acrylate with styrene or methyl methacrylate and subsequent acid-catalyzed hydrolysis of the tert-butyl ester. The copolymers were characterized via nuclear magnetic resonance spectroscopy (NMR), size-exclusion chromatography (SEC), Fourier transform infrared spectroscopy (FTIR), elemental analysis, and acid–base titrations. Copolymer films with a variety of acrylic acid contents were produced by solvent casting, characterized by atomic force microscopy (AFM) and tested for their antimicrobial activity against Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa. The antimicrobial activity of the acidic diblock copolymers increased with increasing acrylic acid content, independent of the copolymer-partner, the chain length and the nanostructure. - Highlights: • Acrylic acid diblock copolymers are antimicrobially active. • The antimicrobial activity depends on the acrylic acid content in the copolymer. • No salts, metals or other antimicrobial agents are needed.

  18. Antimicrobial activity of poly(acrylic acid) block copolymers

    International Nuclear Information System (INIS)

    The increasing number of antibiotic-resistant bacterial strains has developed into a major health problem. In particular, biofilms are the main reason for hospital-acquired infections and diseases. Once formed, biofilms are difficult to remove as they have specific defense mechanisms against antimicrobial agents. Antimicrobial surfaces must therefore kill or repel bacteria before they can settle to form a biofilm. In this study, we describe that poly(acrylic acid) (PAA) containing diblock copolymers can kill bacteria and prevent from biofilm formation. The PAA diblock copolymers with poly(styrene) and poly(methyl methacrylate) were synthesized via anionic polymerization of tert-butyl acrylate with styrene or methyl methacrylate and subsequent acid-catalyzed hydrolysis of the tert-butyl ester. The copolymers were characterized via nuclear magnetic resonance spectroscopy (NMR), size-exclusion chromatography (SEC), Fourier transform infrared spectroscopy (FTIR), elemental analysis, and acid–base titrations. Copolymer films with a variety of acrylic acid contents were produced by solvent casting, characterized by atomic force microscopy (AFM) and tested for their antimicrobial activity against Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa. The antimicrobial activity of the acidic diblock copolymers increased with increasing acrylic acid content, independent of the copolymer-partner, the chain length and the nanostructure. - Highlights: • Acrylic acid diblock copolymers are antimicrobially active. • The antimicrobial activity depends on the acrylic acid content in the copolymer. • No salts, metals or other antimicrobial agents are needed

  19. Facile synthesis and characterization of novel biodegradable amphiphilic block copolymers bearing pendant hydroxyl groups

    International Nuclear Information System (INIS)

    Novel amphiphilic block copolymers bearing pendant hydroxyl groups polylactide-b–poly(3,3-bis(Hydroxymethyl–triazolylmethyl) oxetane)-b–polylactide (PLA-b–PHMTYO-b–PLA) were synthesized via a facile and efficient method. First, the block copolymer intermediates polylactide-b–poly(3,3-Diazidomethyloxetane)-b–polylactide (PLA-b–PBAMO-b–PLA) were synthesized through ring-opening polymerization of lactide using PBAMO as a macroinitiator. Following “Click” reaction of PLA-b–PBAMO-b–PLA with propargyl alcohol provided the targeted amphiphilic block copolymers PLA-b–PHMTYO-b–PLA with pendant hydroxyl groups. The composition and structure of prepared copolymers were characterized by 1H nuclear magnetic resonance (1H NMR) spectroscopy, Fourier transform infrared (FT-IR) and gel permeation chromatography (GPC). The self-assembly behavior of the copolymers in water was investigated by transmission electron microscope (TEM), dynamic light scattering (DLS) and static light scattering (SLS). The results showed that the novel copolymers PLA-b–PHMTYO-b–PLA self-assembled into spherical micelles with diameters ranging from 100 nm to 200 nm in aqueous solution. These copolymers also exhibited low critical micellar concentrations (CMC: 6.9 × 10−4 mg/mL and 3.9 × 10−5 mg/mL, respectively). In addition, the in vitro cytotoxicity of these copolymers was determined in the presence of L929 cells. The results showed that the block copolymers PLA-b–PHMTYO-b–PLA exhibited better biocompatibility. Therefore, these well-defined copolymers are expected to find some applications in drug delivery or tissue engineering. - Highlights: • The method to synthesize PLA-b–PHMTYO-b–PLA is relatively facile and efficient. • PLA-b–PHMTYO-b–PLA self-assembles into spherical micelles with low CMC in water. • PLA-b–PHMTYO-b–PLA exhibits better biocompatibility and biodegradability

  20. Facile synthesis and characterization of novel biodegradable amphiphilic block copolymers bearing pendant hydroxyl groups.

    Science.gov (United States)

    Hu, Gaicen; Fan, Xiaoshan; Xu, Bingcan; Zhang, Delong; Hu, Zhiguo

    2014-10-01

    Novel amphiphilic block copolymers bearing pendant hydroxyl groups polylactide-b-poly(3,3-bis(Hydroxymethyl-triazolylmethyl) oxetane)-b-polylactide (PLA-b-PHMTYO-b-PLA) were synthesized via a facile and efficient method. First, the block copolymer intermediates polylactide-b-poly(3,3-Diazidomethyloxetane)-b-polylactide (PLA-b-PBAMO-b-PLA) were synthesized through ring-opening polymerization of lactide using PBAMO as a macroinitiator. Following "Click" reaction of PLA-b-PBAMO-b-PLA with propargyl alcohol provided the targeted amphiphilic block copolymers PLA-b-PHMTYO-b-PLA with pendant hydroxyl groups. The composition and structure of prepared copolymers were characterized by (1)H nuclear magnetic resonance ((1)H NMR) spectroscopy, Fourier transform infrared (FT-IR) and gel permeation chromatography (GPC). The self-assembly behavior of the copolymers in water was investigated by transmission electron microscope (TEM), dynamic light scattering (DLS) and static light scattering (SLS). The results showed that the novel copolymers PLA-b-PHMTYO-b-PLA self-assembled into spherical micelles with diameters ranging from 100 nm to 200 nm in aqueous solution. These copolymers also exhibited low critical micellar concentrations (CMC: 6.9 × 10(-4)mg/mL and 3.9 × 10(-5)mg/mL, respectively). In addition, the in vitro cytotoxicity of these copolymers was determined in the presence of L929 cells. The results showed that the block copolymers PLA-b-PHMTYO-b-PLA exhibited better biocompatibility. Therefore, these well-defined copolymers are expected to find some applications in drug delivery or tissue engineering. PMID:25175206

  1. Facile synthesis and characterization of novel biodegradable amphiphilic block copolymers bearing pendant hydroxyl groups

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Gaicen; Fan, Xiaoshan; Xu, Bingcan; Zhang, Delong; Hu, Zhiguo, E-mail: zghu@htu.cn

    2014-10-01

    Novel amphiphilic block copolymers bearing pendant hydroxyl groups polylactide-b–poly(3,3-bis(Hydroxymethyl–triazolylmethyl) oxetane)-b–polylactide (PLA-b–PHMTYO-b–PLA) were synthesized via a facile and efficient method. First, the block copolymer intermediates polylactide-b–poly(3,3-Diazidomethyloxetane)-b–polylactide (PLA-b–PBAMO-b–PLA) were synthesized through ring-opening polymerization of lactide using PBAMO as a macroinitiator. Following “Click” reaction of PLA-b–PBAMO-b–PLA with propargyl alcohol provided the targeted amphiphilic block copolymers PLA-b–PHMTYO-b–PLA with pendant hydroxyl groups. The composition and structure of prepared copolymers were characterized by {sup 1}H nuclear magnetic resonance ({sup 1}H NMR) spectroscopy, Fourier transform infrared (FT-IR) and gel permeation chromatography (GPC). The self-assembly behavior of the copolymers in water was investigated by transmission electron microscope (TEM), dynamic light scattering (DLS) and static light scattering (SLS). The results showed that the novel copolymers PLA-b–PHMTYO-b–PLA self-assembled into spherical micelles with diameters ranging from 100 nm to 200 nm in aqueous solution. These copolymers also exhibited low critical micellar concentrations (CMC: 6.9 × 10{sup −4} mg/mL and 3.9 × 10{sup −5} mg/mL, respectively). In addition, the in vitro cytotoxicity of these copolymers was determined in the presence of L929 cells. The results showed that the block copolymers PLA-b–PHMTYO-b–PLA exhibited better biocompatibility. Therefore, these well-defined copolymers are expected to find some applications in drug delivery or tissue engineering. - Highlights: • The method to synthesize PLA-b–PHMTYO-b–PLA is relatively facile and efficient. • PLA-b–PHMTYO-b–PLA self-assembles into spherical micelles with low CMC in water. • PLA-b–PHMTYO-b–PLA exhibits better biocompatibility and biodegradability.

  2. Synthesis of carboxylic block copolymers via reversible addition fragmentation transfer polymerization for tooth erosion prevention.

    Science.gov (United States)

    Lei, Y; Wang, T; Mitchell, J W; Qiu, J; Kilpatrick-Liverman, L

    2014-12-01

    Dental professionals are seeing a growing population of patients with visible signs of dental erosion. The approach currently being used to address the problem typically leverages the enamel protection benefits of fluoride. In this report, an alternative new block copolymer with a hydrophilic polyacrylic acid (PAA) block and a hydrophobic poly(methyl methacrylate) (PMMA) block was developed to similarly reduce the mineral loss from enamel under acidic conditions. This series of PMMA-b-PAA block copolymers was synthesized by reversible addition fragmentation transfer (RAFT) polymerization. Their structures were characterized by gel permeation chromatography (GPC) and (1)H nuclear magnetic resonance (NMR) spectra. The molar fractions of acrylic acid (AA) in the final block copolymer were finely controlled from 0.25 to 0.94, and the molecular weight (Mn) of PMMA-b-PAA was controlled from 10 kDa to 90 kDa. The binding capability of the block copolymer with hydroxyapatite (HAP) was investigated by ultraviolet-visible spectroscopy (UV-Vis) and Fourier transform infrared (FTIR) spectroscopy. FTIR spectra confirmed that the PMMA-b-PAA block copolymer could bind to HAP via bridging bidentate bonds. Both UV-Vis and FTIR spectra additionally indicated that a high polymer concentration and low solution pH favored the polymer binding to HAP. The erosion-preventing efficacy of the PMMA-b-PAA block copolymer in inhibiting HAP mineral loss was quantitatively evaluated by atomic absorption spectroscopy (AAS). Based on the results, polymer treatment reduced the amount of calcium released by 27% to 30% in comparison with the unprotected samples. Scanning electron microscope (SEM) observations indicated that PMMA-b-PAA polymer treatment protected enamel from acid erosion. This new amphiphilic block copolymer has significant potential to be integrated into dentifrices or mouthrinses as an alternative non-fluoride ingredient to reduce tooth erosion. PMID:25248611

  3. Morphology-properties relationship on nanocomposite films based on poly(styrene-block-diene-block-styrene copolymers and silver nanoparticles

    Directory of Open Access Journals (Sweden)

    2011-02-01

    Full Text Available A comparative study on the self-assembled nanostructured morphology and the rheological and mechanical properties of four different triblock copolymers, based on poly(styrene-block-diene-block-styrene and poly(styrene-block-diene-block-styrene matrices, and of their respective nanocomposites with 1 wt% silver nanoparticles, is reported in this work. In order to obtain well-dispersed nanoparticles in the block copolymer matrix, dodecanethiol was used as surfactant, showing good affinity with both nanoparticles and the polystyrene phase of the matrices as predicted by the solubility parameters calculated based on Hoftyzer and Van Krevelen theory. The block copolymer with the highest PS content shows the highest tensile modulus and tensile strength, but also the smallest elongation at break. When silver nanoparticles treated with surfactant were added to the block copolymer matrices, each system studied shows higher mechanical properties due to the good dispersion and the good interface of Ag nanoparticles in the matrices. Furthermore, it has been shown that semiempirical models such as Guth and Gold equation and Halpin-Tsai model can be used to predict the tensile modulus of the analyzed nanocomposites.

  4. Self-organization on multiple length scales in "hairy rod"-coil block copolymer supramolecular complexes

    OpenAIRE

    Hammond, Matthew R.; Klok, Harm-Anton; Mezzenga, Raffaele

    2008-01-01

    A peptide-synthetic hybrid block copolymer, poly(ethylene oxide)-block-poly(L-glutamic acid), is shown to form supramolecular complexes with primary alkylamines of varying alkyl chain lengths (8 to 18 methylene units) in organic solvents via acid-base proton transfer and subsequent ionic bonding. The peptidic block being in the α-helical conformation, these materials behave as coil-"hairy rod" block copolymers, and show hierarchically self-organized nanostructures in the solid state. X-ray sc...

  5. Double network physical gels from elastin-like polypeptide block copolymers: nanoscale control of thermoresponsive reinforcement

    Science.gov (United States)

    Glassman, Matthew; Olsen, Bradley

    2014-03-01

    Triblock copolymers with associative protein midblocks and thermoresponsive endblocks form shear thinning hydrogels with a low yield stress at low temperatures, but can be reinforced by a self-assembled network of the endblock aggregates. Here, we compare the use of bioengineered elastin-like polypeptides (ELPs) to synthetic poly(N-isopropylacrylamide) (PNIPAM) as endblocks to control the self-assembly of the reinforcing network. The temperature dependence of the mechanics of these hydrogels is a strong function of the domain size and morphology in the endblock network. Despite the architectural similarities, triblock ELP fusions and PNIPAM bioconjugates exhibit distinct reinforcement maxima at fixed block composition and polymer concentration, and these differences can be attributed to the nanostructural features of the two systems. Furthermore, in ELP fusions, the amino acid sequence can be readily modified to manipulate the solvation kinetics of the endblock domains. Finally, various endblocks have been combined to form triblock terpolymer hydrogels, demonstrating how the choice of thermoresponsive blocks can be used to tune the reinforcement of shear thinning hydrogels.

  6. Perpendicularly oriented sub-10-nm block copolymer lamellae by atmospheric thermal annealing for one minute

    Science.gov (United States)

    Seshimo, Takehiro; Maeda, Rina; Odashima, Rin; Takenaka, Yutaka; Kawana, Daisuke; Ohmori, Katsumi; Hayakawa, Teruaki

    2016-01-01

    The directed self-assembly (DSA) of block co-polymers (BCPs) can realize next-generation lithography for semiconductors and a variety of soft materials. It is imperative to simultaneously achieve many requirements such as a high resolution, orientation control of micro-domains, etch selectivity, rapid and mild annealing, a low cost, and compatibility with manufacturing for developing suitable BCPs. Here, we describe a new design for modified polysiloxane-based BCPs targeted for sub-10-nm-wide lines, which are able to form perpendicularly oriented lamellar structures in thin films. The hydroxyl groups in the side chains introduced in the polysiloxane block provide a good balance with the polystyrene surface free energy, thereby leading to the perpendicular orientation. Moreover, this orientation can be completed in only one minute at 130 °C in an air atmosphere. Oxygen plasma etching for the thin films results in the achievement of a line width of 8.5 nm.

  7. Effect of Hydrogen-Bonding Junctions on Microphase Separation in Block Copolymers

    Science.gov (United States)

    Stone, Greg; Hedrick, Jim; Nederberg, Fredrik; Balsara, Nitash

    2008-03-01

    The morphology of poly(styrene-block- trimethylene carbonate) (PS-PTMC) copolymers with and without thiourea groups at the junction between the blocks was studied by a combination of small angle X-ray scattering (SAXS) and transmission electron microscopy (TEM). The thiourea groups are known to exhibit inter-molecular hydrogen bonding. We demonstrate that the presence of thiourea groups results in increased segregation between PS and PTMC blocks. We focus on symmetric systems with total molecular weights in the 5 kg/mol range. In conventional block copolymers without hydrogen bonding groups it is difficult to obtain strong segregation in low molecular weight systems because the product chi*N controls segregation (chi is the Flory-Huggins interaction parameter and N is the number of monomers per chain). The incorporation of hydrogen bonding groups may provide a route for the generation of patterns with small, sharply defined features using block copolymers.

  8. Interactions between plasma and block copolymers used in directed self-assembly patterning

    Science.gov (United States)

    Sirard, Stephen; Azarnouche, Laurent; Gurer, Emir; Durand, William; Maher, Michael; Mori, Kazunori; Blachut, Gregory; Janes, Dustin; Asano, Yusuke; Someya, Yasunobu; Hymes, Diane; Graves, David; Ellison, Christopher J.; Willson, C. Grant

    2016-03-01

    The directed self-assembly (DSA) of block copolymers offers a promising route for scaling feature sizes below 20 nm. At these small dimensions, plasmas are often used to define the initial patterns. It is imperative to understand how plasmas interact with each block in order to design processes with sufficient etch contrast and pattern fidelity. Symmetric lamella forming block copolymers including, polystyrene-b-poly(methyl methacrylate) and several high-χ silicon-containing and tin-containing block copolymers were synthesized, along with homopolymers of each block, and exposed to various oxidizing, reducing, and fluorine-based plasma processes. Etch rate kinetics were measured, and plasma modifications of the materials were characterized using XPS, AES, and FTIR. Mechanisms for achieving etch contrast were elucidated and were highly dependent on the block copolymer architecture. For several of the polymers, plasma photoemissions were observed to play an important role in modifying the materials and forming etch-resistant protective layers. Furthermore, it was observed for the silicon- and tin-containing polymers that an initial transient state exists, where the polymers exhibit an enhanced etch rate, prior to the formation of the etch-resistant protective layer. Plasma developed patterns were demonstrated for the differing block copolymer materials with feature sizes ranging from 20 nm down to approximately 5 nm.

  9. Control of Crystallization to Promote Microphase Separation in Fully Conjugated Block Copolymers

    Science.gov (United States)

    Lee, Youngmin; Le, Thinh P.; Seibers, Zach; Kilbey, S. Michael, II; Wang, Qing; Gomez, Enrique D.

    Donor -acceptor fully conjugated block copolymers, where donor and acceptor conjugated polymers are covalently bonded together, are interesting as single-component active-layer materials for photovoltaics because it can adopt mesoscale microphase separated structures with length scales comparable to the exciton diffusion length. Nevertheless, due to the strong crystallization of poly(3-hexylthiophene-2,5-diyl) (P3HT), morphologies of fully conjugated block copolymers containing P3HT are predominantly driven by crystallization as opposed to microphase separation. We control the crystallization in block copolymers to promote microphase separation in fully conjugated block copolymers through the addition of small amounts of 3-octylthiophene to the polymerization of P3HT. Poly(3-hexylthiophene-2,5-diyl- r-3-octylthiophene-2,5-diyl)-block-poly((9,9-dioctylfluorene-2,7-diyl)-alt-(4,7-di(thiophene-2-yl)-2,1,3-benzothiadiazole)-5',5''-diyl) (P3HT- b-PFTBT) copolymers were prepared by Grignard metathesis for the alkylthiophene block followed by chain extension through a Suzuki-Miyaura polycondensation. We compare the crystallization, self-assembly and performance in devices of P3HT-b-PFTBT with a few mole percent of 3-octylthiophene in the P3HT block. Center for Nanophase Materials Sciences, Oak Ridge National Laboratory, Oak Ridge, TN 37831.

  10. Preparation of Pickering double emulsions using block copolymer worms.

    Science.gov (United States)

    Thompson, Kate L; Mable, Charlotte J; Lane, Jacob A; Derry, Mathew J; Fielding, Lee A; Armes, Steven P

    2015-04-14

    The rational formulation of Pickering double emulsions is described using a judicious combination of hydrophilic and hydrophobic block copolymer worms as highly anisotropic emulsifiers. More specifically, RAFT dispersion polymerization was utilized to prepare poly(lauryl methacrylate)-poly(benzyl methacrylate) worms at 20% w/w solids in n-dodecane and poly(glycerol monomethacrylate)-poly(2-hydroxypropyl methacrylate)-poly(benzyl methacrylate) worms at 13% w/w solids in water by polymerization-induced self-assembly (PISA). Water-in-oil-in-water (w/o/w) double emulsions can be readily prepared with mean droplet diameters ranging from 30 to 80 μm using a two-stage approach. First, a w/o precursor emulsion comprising 25 μm aqueous droplets is prepared using the hydrophobic worms, followed by encapsulation within oil droplets stabilized by the hydrophilic worms. The double emulsion droplet diameter and number of encapsulated water droplets can be readily varied by adjusting the stirring rate employed during the second stage. For each stage, the droplet volume fraction is relatively high at 0.50. The double emulsion nature of the final formulation was confirmed by optical and fluorescence microscopy studies. Such double emulsions are highly stable to coalescence, with little or no change in droplet diameter being detected over storage at 20 °C for 10 weeks as judged by laser diffraction. Preliminary experiments indicate that the complementary o/w/o emulsions can also be prepared using the same pair of worms by changing the order of homogenization, although somewhat lower droplet volume fractions were required in this case. Finally, we demonstrate that triple and even quadruple emulsions can be formulated using these new highly anisotropic Pickering emulsifiers. PMID:25834923

  11. Surface affinity role in graphoepitaxy of lamellar block copolymers

    Science.gov (United States)

    Claveau, G.; Quemere, P.; Argoud, M.; Hazart, J.; Pimenta Barros, P.; Sarrazin, A.; Posseme, N.; Tiron, R.; Chevalier, X.; Nicolet, C.; Navarro, C.

    2016-03-01

    Overcoming the optical limitations of 193nm immersion lithography can be achieved using Directed Self Assembly (DSA) of block-copolymers (BCPs) as a low-cost and versatile complementary technique. The goal of this paper is to investigate the potential of DSA to address line and space (L/S) high resolution patterning by performing the density multiplication of lines with the graphoepitaxy approach. As surface affinity is a key parameter in self-assembly, three variations, or "flavors", of DSA template affinity are investigated regarding several success criteria such as morphology control or defectivity. More precisely, both the methodology to register DSA defects and the impact of process parameters on defectivity are detailed. Using the 300mm pilot line available in LETI and Arkema's advanced materials, we investigate process optimization of DSA line/space patterning of a 38nm period lamellar PS-b-PMMA BCP (L38). For this study, our integration scheme, depicted in figure 2-1, is based on BCP self-assembly inside organic hard mask guiding patterns obtained using 193i nm lithography. Defect analysis coupled with the fine tuning of process parameters (annealing, brush material) provided the optimum conditions for the L38 self-assembly. Using such conditions, DSA using the three affinity flavors is investigated by means of SEM top-view and cross-section review. Lithographic performances of one selected flavor are then evaluated with the comparison of Process Windows (PWs) function of either commensurability, morphology or LWR. This work is a first step in finding the best process for an industrial graphoepitaxy approach.

  12. Carbon nanotubes with small and tunable diameters from poly(ferrocenylsilane)-block-polysiloxane diblock copolymers.

    Science.gov (United States)

    Lu, Jennifer Q; Rider, David A; Onyegam, Emanuel; Wang, Hai; Winnik, Mitchell A; Manners, Ian; Cheng, Qian; Fu, Qiang; Liu, Jie

    2006-05-23

    Iron-containing nanostructures produced from various self-assembled poly(ferrocenylsilane)-block-polysiloxane thin films are catalytically active for the initiation and growth of high density, small diameter carbon nanotubes (CNTs). Moreover, the tube diameter and density can be tuned by adjusting the chain lengths of the block copolymer. Iron-containing nanostructures from poly(ferrocenylmethylethylsilane)-b-poly(methylvinylsiloxane) polymer with 25 repeat units of an iron-containing segment and 265 repeat units of a non-iron-containing segment are able to produce CNTs with diameters around or less than 1 nm. Lithographically selective growth of CNTs across a large surface area has been demonstrated using this polymer system. Under the same growth condition, it has been found that the yield of defect-free CNTs varies with the size of the catalytically active nanostructures, which are dictated by the chain lengths of the two blocks. This result indicates that, for a specific-sized catalyst nanocluster, a unique set of growth conditions is required for synthesizing high yield, defect-free CNTs. This finding further addresses the importance of using uniform-sized catalyst-containing nanostructures for consistently achieving high-yield and high-quality CNTs with a minimum number of defects and amount of amorphous carbon. PMID:16700610

  13. Synthesis and characterization of polystyrene-poly(ethylene oxide)-heparin block copolymers

    OpenAIRE

    Vulić, I.; Okano, T.; Kim, S W; J. Feijen

    1988-01-01

    A procedure for the preparation of new block copolymers composed of a hydrophobic block of polystyrene, a hydrophilic spacer-block of poly(ethylene oxide) and a bioactive block of heparin was investigated. Polystyrene with one amino group per chain was synthesized by free radical oligomerization of styrene in dimethylformamide, using 2-aminoethanethiol as a chain transfer agent. This amino group was used in the coupling reaction with amino-telechelic poly(ethylene oxide) to produce an AB type...

  14. Improved synthesis of polystyrene-poly(ethylene oxide)-heparin block copolymers

    OpenAIRE

    Vulic, I.; Loman, A.J.B.; J. Feijen; Okano, T.; Kim, S W

    1990-01-01

    A novel procedure for the synthesis of block copolymers composed of a hydrophobic block of polystyrene, a hydrophilic block of poly(ethylene oxide) and a bioactive block of nitrous acid-degraded heparin was developed. Amino-semitelechelic polystyrene was prepared by anionic polymerization of styrene in cyclohexane, using sec-butyllithium as initiator and N-(benzylidene)trimethylsilylamide as terminator. After purification using preparative column chromatography, polystyrene with one amino gro...

  15. Self-Assembled Structures of PMAA-PMMA Block Copolymers : Synthesis, Characterization, and Self-Consistent Field Computations

    NARCIS (Netherlands)

    Li, Feng; Schellekens, Mike; de Bont, Jens; Peters, Ron; Overbeek, Ad; Leermakers, Frans A. M.; Tuinier, Remco

    2015-01-01

    Block copolymers composed of methacrylic acid (MAA) and methyl methacrylate (MMA) blocks are interesting candidates for replacing surfactants in emulsion polymerization methods. Here the synthesis and experimental characterization of well-defined PMAA-PMMA block copolymers made via RAFT polymerizati

  16. Influence of polydispersity on the phase behavior of statistical multiblock copolymers with Schultz-Zimm block molecular weight distributions

    NARCIS (Netherlands)

    Angerman, H.J.; Brinke, G. ten; Slot, J.J.M.

    1999-01-01

    In this paper we investigate in a systematic way the influence of polydispersity in the block lengths on the phase behavior of AB-multiblock copolymer melts. As model system we take a polydisperse multiblock copolymer for which both the A-blocks and the B-blocks satisfy a Schultz-Zimm distribution.

  17. Paclitaxel-incorporated nanoparticles using block copolymers composed of poly(ethylene glycol)/poly(3-hydroxyoctanoate)

    OpenAIRE

    Kim, Hyun Yul; Ryu, Je Ho; Chu, Chong Woo; Son, Gyung Mo; Jeong, Young-IL; Kwak, Tae-Won; Kim, Do Hyung; Chung, Chung-Wook; Rhee, Young Ha; Kang, Dae Hwan; Kim, Hyung Wook

    2014-01-01

    Block copolymers composed of poly(3-hydroxyoctanoate) (PHO) and methoxy poly(ethylene glycol) (PEG) were synthesized to prepare paclitaxel-incorporated nanoparticle for antitumor drug delivery. In a 1H-NMR study, chemical structures of PHO/PEG block copolymers were confirmed and their molecular weight (M.W.) was analyzed with gel permeation chromatography (GPC). Paclitaxel as a model anticancer drug was incorporated into the nanoparticles of PHO/PEG block copolymer. They have spherical shapes...

  18. Analytic Structure of the SCFT Energy Functional of Multicomponent Block Copolymers

    CERN Document Server

    Jiang, Kai; Zhang, Pingwen

    2013-01-01

    This paper concerns the analytic structure of the self-consistent field theory (SCFT) energy functional of multicomponent block copolymer systems which contain more than two chemically distinct blocks. The SCFT has enjoyed considered success and wide usage in investigation of the complex phase behavior of block copolymers. It is well-known that the physical solutions of the SCFT equations are saddle points, however, the analytic structure of the SCFT energy functional has received little attention over the years. A recent work by Fredrickson and collaborators [see the monograph by Fredrickson, The Equilibrium Theory of Inhomogeneous Polymers, (2006), pp. 203-209] has analysed the mathematical structure of the field energy functional for polymeric systems, and clarified the index-1 saddle point nature of the problem produced by the incompressibility constraint. In this paper, our goals are to draw further attention to multicomponent block copolymers utilizing the Hubbard-Stratonovich transformation used by Fre...

  19. The Organization of Nanoporous Structure Using Controlled Micelle Size from MPEG-b-PDLLA Block Copolymers

    International Nuclear Information System (INIS)

    Selected MPEG-b-PDLLA block copolymers have been synthesized by ring-opening polymerization with systematic variation of the chain lengths of the resident hydrophilic and hydrophobic blocks. The size and shape of the micelles that spontaneously form in solution are then controlled by the characteristics of the block copolymer template. All the materials prepared in this study showed the tunable pore size of 20-80 A with the increase of hydrophobic chain lengths and up to 660 m2/g of specific surface area. The formation mechanism of these nanoporous structures obtained by controlling the micelle size has been confirmed using both liquid and solid state 13C and 29Si NMR techniques. This work verifies the formation mechanism of nanoporous structures in which the pore size and wall thickness are closely dependent on the size of hydrophobic cores and hydrophilic shells of the block copolymer templates

  20. 125l-Labeled PEO/PLA block copolymer: biodistribution studies in rats

    Czech Academy of Sciences Publication Activity Database

    Nováková, K.; Lázníček, M.; Rypáček, František; Machová, Luďka

    2002-01-01

    Roč. 17, č. 4 (2002), s. 285-296. ISSN 0883-9115 R&D Projects: GA AV ČR KSK4055109 Institutional research plan: CEZ:AV0Z4050913 Keywords : block copolymer micelles * poly(D,L-lactide-block-ethylene oxide) * biodistribution Subject RIV: CC - Organic Chemistry Impact factor: 0.525, year: 2002

  1. Multi-block sulfonated poly(phenylene) copolymer proton exchange membranes

    Science.gov (United States)

    Fujimoto, Cy H.; Hibbs, Michael; Ambrosini, Andrea

    2012-02-07

    Improved multi-block sulfonated poly(phenylene) copolymer compositions, methods of making the same, and their use as proton exchange membranes (PEM) in hydrogen fuel cells, direct methanol fuel cells, in electrode casting solutions and electrodes. The multi-block architecture has defined, controllable hydrophobic and hydrophilic segments. These improved membranes have better ion transport (proton conductivity) and water swelling properties.

  2. Polymer Segmental Cross-Correlations from Dielectric Relaxation Spectra of Block Copolymers

    OpenAIRE

    Phillies, George D. J.

    2011-01-01

    Dielectric relaxation spectra of block polymers containing sequential type-A dipoles are considered. Spectra of a specific set of block copolymers can be combined to isolate the dynamic cross-correlation between the motions of two distinct parts of the same polymer chain. Unlike past treatments of this problem, no model is assumed for the underlying polymer dynamics.

  3. Photocatalytic Nanostructuring of Graphene Guided by Block Copolymer Self-Assembly

    DEFF Research Database (Denmark)

    Wang, Zhongli; Li, Tao; Schulte, Lars;

    2016-01-01

    graphene nanomesh was fabricated by photocatalysis of single-layer graphene suspended on top of TiO2-covered nanopillars, which were produced by combining block copolymer nanolithography with atomic layer deposition. Graphene nanoribbons were also prepared by the same method applied to a line-forming block...

  4. Melt and Solid-State Structures of Polydisperse Polyolefin Block Copolymers

    Science.gov (United States)

    Register, Richard; Li, Sheng

    2013-03-01

    Recent developments in coordinative chain transfer polymerization have enabled the synthesis of ethylene-co-octene block copolymers, where the blocks are either crystallizable (an ethylene-co-octene random copolymer block with low octene content) or amorphous (analogous block with high octene content). With a suitable choice of catalyst type(s) and reactor train configuration, accessible chain architectures include diblock, where each block ideally has the most-probable distribution of chain lengths, and multiblock, where both the individual blocks and the number of blocks per chain follow the most-probable distribution. With a sufficiently large interblock octene differential, block copolymers of both architectures, containing roughly equal masses of the two types of block, self-assemble in the melt into well-ordered lamellar structures, despite the large polydispersity. Interblock mixing, induced by the modest Flory interaction parameter and the broad distribution of block lengths, yields an enormous domain spacing (> 100 nm) despite the relatively low average block molecular weights (< 50 kg/mol). Extensive interblock mixing also allows the polyethylene crystals to grow freely and nearly isotropically across the domain interfaces, while preserving the domain structure present in the melt; in the solid state, the optical and x-ray contrasts between dissimilar domains are greatly enhanced due to their different levels of crystallinity. (Work conducted in collaboration with Jeffrey Weinhold, Philip Hustad, and Brian Landes of Dow Chemical Core R&D.) Support from the NSF Polymers Program (DMR-1003942).

  5. DETERMINATION OF THE CRYSTALLINITY IN DIFFERENT TYPE POLY (OXYETHYLENE -STYRENE )BLOCK COPOLYMERS BY X- RAY DIFFRACTION METHOD

    Institute of Scientific and Technical Information of China (English)

    YAO Ning

    1989-01-01

    By means of the intensity theory of X- ray scattering and the two - phase concept of high polymer, the basic formula of the crystallinity in block copolymers has been proposed after the corrections of atomic, temperature, absorption, Lorentz and polarization factor. Application of this method to different type poly (oxyethylene - styrene) block copolymers and the same type block copolymers with different EO contents indicates that the crystallinity in poly (oxyethylene - styrene) block copolymers increases with the increase of the EO content and decreases in the order: PEO - PS - PEO > PEO - PS > PS - PEO - PS.

  6. Synthesis of manganese oxide supported on mesoporous titanium oxide: Influence of the block copolymer

    Energy Technology Data Exchange (ETDEWEB)

    Schmit, F. [Laboratoire des Multimatériaux et Interfaces, UMR CNRS 5615, Bât. Berthollet, Université Claude Bernard—Lyon 1, 43 Bd 11 novembre 1918, 69622 Villeurbanne (France); IRCELYON, Institut de recherches sur la catalyse et l’environnement de Lyon (UMR 5256 CNRS/Université Lyon 1), Lyon (France); Bois, L., E-mail: laurence.bois@univ-lyon1.fr [Laboratoire des Multimatériaux et Interfaces, UMR CNRS 5615, Bât. Berthollet, Université Claude Bernard—Lyon 1, 43 Bd 11 novembre 1918, 69622 Villeurbanne (France); Chiriac, R.; Toche, F.; Chassagneux, F. [Laboratoire des Multimatériaux et Interfaces, UMR CNRS 5615, Bât. Berthollet, Université Claude Bernard—Lyon 1, 43 Bd 11 novembre 1918, 69622 Villeurbanne (France); Besson, M.; Descorme, C. [IRCELYON, Institut de recherches sur la catalyse et l’environnement de Lyon (UMR 5256 CNRS/Université Lyon 1), Lyon (France); Khrouz, L. [ENS LYON Laboratoire de Chimie (LR6, site Monod), 46, allée d’Italie, 69364 Lyon Cedex 07 (France)

    2015-01-15

    Manganese oxides supported on mesoporous titanium oxides were synthesized via a sol–gel route using block copolymer self-assembly. The oxides were characterized by X-ray diffraction, infrared spectroscopy, thermal analyses, nitrogen adsorption/desorption, electron microscopy and electronic paramagnetic resonance. A mesoporous anatase containing amorphous manganese oxide particles could be obtained with a 0.2 Mn:Ti molar ratio. At higher manganese loading (0.5 Mn:Ti molar ratio), segregation of crystalline manganese oxide occurred. The influence of block copolymer and manganese salt on the oxide structure was discussed. The evolution of the textural and structural characteristics of the materials upon hydrothermal treatment was also investigated. - Graphical abstract: One-pot amorphous MnO{sub 2} supported on mesoporous anataseTiO{sub 2}. - Highlights: • Mesoporous manganese titanium oxides were synthesized using block copolymer. • Block copolymers form complexes with Mn{sup 2+} from MnCl{sub 2}. • With block copolymer, manganese oxide can be dispersed around the titania crystallites. • With Mn(acac){sub 2}, manganese is dispersed inside titania. • MnOOH crystallizes outside mesoporous titania during hydrothermal treatment.

  7. Epitaxial relationships for hexagonal-to-cubic phase transition in a block copolymer mixture

    DEFF Research Database (Denmark)

    Schulz, M.F.; Bates, F.S.; Almdal, K.;

    1994-01-01

    Small-angle neutron scattering experiments have revealed an epitaxial relationship between the hexagonal cylinder phase, and a bicontinuous cubic phase with Ia3dBAR space group symmetry, in a poly(styrene)-poly(2-vinylpyridine) diblock copolymer mixture. Proximity to the order-disorder transition...... and an inelastic low frequency rheological response suggest that the cubic phase is stabilized by fluctuations. These results identify block copolymers as model compounds for investigating the thermodynamics and dynamics of complex ''soft'' condensed matter....

  8. An Observation on the Microphase Separation of Poly(methyl methacrylate)-block-Polystyrene Copolymer

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The phase behavior of a well-defined poly(methyl methacrylate)-b-polystyrene block copolymer was studied by transmission electron microscope.The results show that a microphase transition may have occurred in the copolymer film.A kind of lamellae and an ordered bicontinuous double-diamond morphology are observed clearly.The lamellar morphology reveals a larger period of about 400 nm.

  9. Magnetic properties and morphology of block copolymer-cobalt oxide nanocomposites

    International Nuclear Information System (INIS)

    The morphology and magnetic properties of diblock copolymer templated ferrimagnetic cobalt oxide nanoparticles are reported. Ring opening metathesis polymerization (ROMP) was used to synthesize a novel cobalt diblock copolymer, where cobalt is directly attached to the polymer chain. Gel permeation chromatography (GPC) was performed to determine molecular weight distribution. Transmission electron microscope (TEM), UV-Vis, FTIR, and vibrating sample magnetometer (VSM) were used to characterize the block copolymer nanocomposite. The nanocomposite films were weakly ferrimagnetic at room temperature. The cobalt oxide nanoparticles were uniformly dispersed within the polymer matrix with an average radius of 4.9+/-0.9nm

  10. Magnetic properties and morphology of block copolymer-cobalt oxide nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, Sufi R. [Department of Chemical Engineering, University of Maryland, College Park, MD 20742-2111 (United States); Kofinas, Peter [Department of Chemical Engineering, University of Maryland, College Park, MD 20742-2111 (United States)]. E-mail: kofinas@umd.edu

    2005-03-01

    The morphology and magnetic properties of diblock copolymer templated ferrimagnetic cobalt oxide nanoparticles are reported. Ring opening metathesis polymerization (ROMP) was used to synthesize a novel cobalt diblock copolymer, where cobalt is directly attached to the polymer chain. Gel permeation chromatography (GPC) was performed to determine molecular weight distribution. Transmission electron microscope (TEM), UV-Vis, FTIR, and vibrating sample magnetometer (VSM) were used to characterize the block copolymer nanocomposite. The nanocomposite films were weakly ferrimagnetic at room temperature. The cobalt oxide nanoparticles were uniformly dispersed within the polymer matrix with an average radius of 4.9+/-0.9nm.

  11. First observation of an ordered microphase in melts of poly(oxyethylene)-poly(oxypropylene) block copolymers

    DEFF Research Database (Denmark)

    Patrick, J.; Fairclough, J.P.A.; Yu, G.E.;

    2000-01-01

    The first observation of ordered microphase structures in poly(oxyethylene)-poly(oxypropylene) diblock copolymers melts is reported. Two diblock copolymers were synthesised by anionic polymerisation, i.e. E130P58 and E107P69 where E represents an oxyethylene unit, OCH2CH2, and P an oxypropylene...... triblock copolymer with perdeuterated P blocks, E(33)dP(42)E(33), was synthesised and studied in the melt phase by small-angle neutron scattering. This allowed determination of the temperature dependence of the Flory-Huggins interaction parameter for the poly(oxyethylene)-poly(oxypropylene) system, i...

  12. Small angle neutron scattering study of the micelle structure of amphiphilic block copolymers

    International Nuclear Information System (INIS)

    The amphiphilic block copolymers of vinyl ether were prepared by living cationic polymerization. The partially deuterated copolymers for SANS experiments were especially synthesized by introducing deuterated phenyl units in the hydrophobic chain. SANS measurements were performed for aqueous solutions of these copolymers by changing H2O/D2O ratios. The SANS profiles indicate that the micelles in the present system exhibit a core-shell structure and that the size and shape of micelles are largely dependent on the length of hydrophobic chain. The micelle of shorter hydrophobic chain was found to be nearly spherical, whereas the micelle of longer hydrophobic chain was confirmed to have an ellipsoidal shape

  13. Structure and ionic conductivity of block copolymer electrolytes over a wide salt concentration range

    Science.gov (United States)

    Chintapalli, Mahati; Le, Thao; Venkatesan, Naveen; Thelen, Jacob; Rojas, Adriana; Balsara, Nitash

    Block copolymer electrolytes are promising materials for safe, long-lasting lithium batteries because of their favorable mechanical and ion transport properties. The morphology, phase behavior, and ionic conductivity of a block copolymer electrolyte, SEO mixed with LiTFSI was studied over a wide, previously unexplored salt concentration range using small angle X-ray scattering, differential scanning calorimetry and ac impedance spectroscopy, respectively. SEO exhibits a maximum in ionic conductivity at twice the salt concentration that PEO, the homopolymer analog of the ion-containing block, does. This finding is contrary to prior studies that examined a more limited range of salt concentrations. In SEO, the phase behavior of the PEO block and LiTFSI closely resembles the phase behavior of homopolymer PEO and LiTFSI. The grain size of the block copolymer morphology was found to decrease with increasing salt concentration, and the ionic conductivity of SEO correlates with decreasing grain size. Structural effects impact the ionic conductivity-salt concentration relationship in block copolymer electrolytes. SEO: polystyrene-block-poly(ethylene oxide); also PS-PEO LiTFSI: lithium bis(trifluoromethanesulfonyl imide

  14. Polydimethylsiloxane-polymethacrylate block copolymers tethering quaternary ammonium salt groups for antimicrobial coating

    International Nuclear Information System (INIS)

    Highlights: • A series of PDMS-b-QPDMAEMA block copolymers were synthesized via RAFT polymerization. • The composition and morphology of the copolymer films strongly depended on the content of QPDMAEMA. • Migration of QPDMAEMA blocks toward surface was promoted when contacting with water. • Heterogeneous film surfaces with higher N+ content exhibited more obvious antimicrobial activity. - Abstract: Block copolymers PDMS-b-PDMAEMA were synthesized via reversible addition-fragmentation chain transfer (RAFT) polymerization involving N,N-dimethylaminoethyl methacrylate (DMAEMA) by using poly(dimethylsiloxane) (PDMS) macro-chain transfer agent. And, the tertiary amino groups in PDMAEMA were quaternized with n-octyliodide to provide quaternary ammonium salts (QPDMAEMA). The well-defined copolymers generated composition variation and morphology evolvement on film surfaces, which were characterized by X-ray photoelectron spectroscopy, atomic force microscopy, and contact angle measurements. The results indicated that the enrichment of QPDMAEMA brought about lower elemental ratios of Si/N on the film surfaces. The surface morphologies evolved with the variations of QPDMAEMA content, and the variation trend of film roughness was exactly opposite to that of water contact angle hysteresis. With regard to structure-antimicrobial relationships, the copolymer films had more evident antimicrobial activity against Gram-positive, Bacillus subtilis, and the surfaces with heterogeneous morphology and higher N+ content presented better antimicrobial activity. The functionalized copolymers based PDMS and quaternary ammonium salts materials have the potential applications as antimicrobial coatings

  15. Polydimethylsiloxane-polymethacrylate block copolymers tethering quaternary ammonium salt groups for antimicrobial coating

    Energy Technology Data Exchange (ETDEWEB)

    Qin, Xiaoshuai; Li, Yancai; Zhou, Fang; Ren, Lixia; Zhao, Yunhui, E-mail: zhaoyunhui@tju.edu.cn; Yuan, Xiaoyan

    2015-02-15

    Highlights: • A series of PDMS-b-QPDMAEMA block copolymers were synthesized via RAFT polymerization. • The composition and morphology of the copolymer films strongly depended on the content of QPDMAEMA. • Migration of QPDMAEMA blocks toward surface was promoted when contacting with water. • Heterogeneous film surfaces with higher N{sup +} content exhibited more obvious antimicrobial activity. - Abstract: Block copolymers PDMS-b-PDMAEMA were synthesized via reversible addition-fragmentation chain transfer (RAFT) polymerization involving N,N-dimethylaminoethyl methacrylate (DMAEMA) by using poly(dimethylsiloxane) (PDMS) macro-chain transfer agent. And, the tertiary amino groups in PDMAEMA were quaternized with n-octyliodide to provide quaternary ammonium salts (QPDMAEMA). The well-defined copolymers generated composition variation and morphology evolvement on film surfaces, which were characterized by X-ray photoelectron spectroscopy, atomic force microscopy, and contact angle measurements. The results indicated that the enrichment of QPDMAEMA brought about lower elemental ratios of Si/N on the film surfaces. The surface morphologies evolved with the variations of QPDMAEMA content, and the variation trend of film roughness was exactly opposite to that of water contact angle hysteresis. With regard to structure-antimicrobial relationships, the copolymer films had more evident antimicrobial activity against Gram-positive, Bacillus subtilis, and the surfaces with heterogeneous morphology and higher N{sup +} content presented better antimicrobial activity. The functionalized copolymers based PDMS and quaternary ammonium salts materials have the potential applications as antimicrobial coatings.

  16. Thermosensitive PNIPAM-b-HTPB block copolymer micelles: molecular architectures and camptothecin drug release.

    Science.gov (United States)

    Luo, Yan-Ling; Yang, Xiao-Li; Xu, Feng; Chen, Ya-Shao; Zhang, Bin

    2014-02-01

    Two kinds of thermo-sensitive poly(N-isoproplacrylamide) (PNIPAM) block copolymers, AB4 four-armed star multiblock and linear triblock copolymers, were synthesized by ATRP with hydroxyl-terminated polybutadiene (HTPB) as central blocks, and characterization was performed by (1)H NMR, FT-IR and SEC. The multiblock copolymers could spontaneously assemble into more regular spherical core-shell nanoscale micelles than the linear triblock copolymer. The physicochemical properties were detected by a surface tension technique, nano particle analyzer, TEM, DLS and UV-vis measurements. The multiblock copolymer micelles had lower critical micelle concentration than the linear counterpart, TEM size from 100 to 120 nm and the hydrodynamic diameters below 150 nm. The micelles exhibited thermo-dependent size change, with low critical solution temperature about 33-35 °C. The characteristic parameters were affected by the composition ratios, length of PNIPAM blocks and molecular architectures. The camptothecin release demonstrated that the drug release was thermo-responsive, accompanied by the temperature-induced structural changes of the micelles. MTT assays were performed to evaluate the biocompatibility or cytotoxicity of the prepared copolymer micelles. PMID:24184534

  17. Thermoresponsive and Redox Behaviors of Poly(N-isopropylacrylamide)-Based Block Copolymers Having TEMPO Groups as Their Side Chains

    OpenAIRE

    Toru Uemukai; Tomoya Hioki; Manabu Ishifune

    2013-01-01

    Thermoresponsive and redox-active block copolymers having 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO) moieties have been synthesized by using the reversible addition-fragmentation chain transfer (RAFT) polymerization technique. N-Isopropylacrylamide (NIPAAm) and 2,2,6,6-tetramethylpiperidyl methacrylate (TEMPMA) monomers were copolymerized stepwise under RAFT polymerization conditions to afford the thermoresponsive block copolymers, PNIPAAm-block-PTEMPMA and PNIPAAm-block-PTEMPMA-block-PNIPA...

  18. Self-assembled incorporation of modulated block copolymer nanostructures in phase-change memory for switching power reduction.

    Science.gov (United States)

    Park, Woon Ik; You, Byoung Kuk; Mun, Beom Ho; Seo, Hyeon Kook; Lee, Jeong Yong; Hosaka, Sumio; Yin, You; Ross, C A; Lee, Keon Jae; Jung, Yeon Sik

    2013-03-26

    Phase change memory (PCM), which exploits the phase change behavior of chalcogenide materials, affords tremendous advantages over conventional solid-state memory due to its nonvolatility, high speed, and scalability. However, high power consumption of PCM poses a critical challenge and has been the most significant obstacle to its widespread commercialization. Here, we present a novel approach based on the self-assembly of a block copolymer (BCP) to form a thin nanostructured SiOx layer that locally blocks the contact between a heater electrode and a phase change material. The writing current is decreased 5-fold (corresponding to a power reduction by 1/20) as the occupying area fraction of SiOx nanostructures is increased from a fill factor of 9.1% to 63.6%. Simulation results theoretically explain the current reduction mechanism by localized switching of BCP-blocked phase change materials. PMID:23451771

  19. Block Co-Polymers for Nanolithography: Rapid Microwave Annealing for Pattern Formation on Substrates

    Directory of Open Access Journals (Sweden)

    Dipu Borah

    2015-03-01

    Full Text Available The integration of block copolymer (BCP self-assembled nanopattern formation as an alternative lithographic tool for nanoelectronic device fabrication faces a number of challenges such as defect densities, feature size, pattern transfer, etc. Key barriers are the nanopattern process times and pattern formation on current substrate stack layers such as hard masks (e.g., silicon nitride, Si3N4. We report a rapid microwave assisted solvothermal (in toluene environments self-assembly and directed self-assembly of a polystyrene-block-polydimethylsiloxane (PS-b-PDMS BCP thin films on planar and topographically patterned Si3N4 substrates. Hexagonally arranged, cylindrical structures were obtained and good pattern ordering was achieved. Factors affecting BCP self-assembly, notably anneal time and temperature, were studied and seen to have significant effects. Graphoepitaxy within the topographical structures provided long range, translational alignment of the patterns. The effect of surface topography feature size and spacing was investigated. The solvothermal microwave based technique used to provide periodic order in the BCP patterns showed significant promise and ordering was achieved in much shorter periods than more conventional thermal and solvent annealing methods. The implications of the work in terms of manufacturing technologies are discussed.

  20. Coarse-grained molecular dynamics modeling of the kinetics of lamellar block copolymer defect annealing

    Science.gov (United States)

    Peters, Andrew J.; Lawson, Richard A.; Nation, Benjamin D.; Ludovice, Peter J.; Henderson, Clifford L.

    2016-01-01

    State-of-the-art block copolymer (BCP)-directed self-assembly (DSA) methods still yield defect densities orders of magnitude higher than is necessary in semiconductor fabrication despite free-energy calculations that suggest equilibrium defect densities are much lower than is necessary for economic fabrication. This disparity suggests that the main problem may lie in the kinetics of defect removal. This work uses a coarse-grained model to study the rates, pathways, and dependencies of healing a common defect to give insight into the fundamental processes that control defect healing and give guidance on optimal process conditions for BCP-DSA. It is found that bulk simulations yield an exponential drop in defect heal rate above χN˜30. Thin films show no change in rate associated with the energy barrier below χN˜50, significantly higher than the χN values found previously for self-consistent field theory studies that neglect fluctuations. Above χN˜50, the simulations show an increase in energy barrier scaling with 1/2 to 1/3 of the bulk systems. This is because thin films always begin healing at the free interface or the BCP-underlayer interface, where the increased A-B contact area associated with the transition state is minimized, while the infinitely thick films cannot begin healing at an interface.

  1. Silk-collagen-like block copolymers with charged blocks : self-assembly into nanosized ribbons and macroscopic gels

    NARCIS (Netherlands)

    Martens, A.A.

    2008-01-01

    The research described in this thesis concerns the design, biotechnological production, and physiochemical study of large water-soluble (monodisperse) protein triblock-copolymers with sequential blocks, some of which are positively or negatively charged and self-assemble in response to a change in p

  2. Synthesis of Carboxylic Block Copolymers via Reversible Addition Fragmentation Transfer Polymerization for Tooth Erosion Prevention

    OpenAIRE

    Lei, Y.; Wang, T.; Mitchell, J. W.; Qiu, J.; Kilpatrick-Liverman, L.

    2014-01-01

    Dental professionals are seeing a growing population of patients with visible signs of dental erosion. The approach currently being used to address the problem typically leverages the enamel protection benefits of fluoride. In this report, an alternative new block copolymer with a hydrophilic polyacrylic acid (PAA) block and a hydrophobic poly(methyl methacrylate) (PMMA) block was developed to similarly reduce the mineral loss from enamel under acidic conditions. This series of PMMA-b-PAA blo...

  3. A functionalizable reverse thermal gel based on a polyurethane/PEG block copolymer

    OpenAIRE

    Park, Daewon; Wu, Wei; Wang, Yadong

    2011-01-01

    Injectable reverse thermal gels have great potentials as biomaterials for tissue engineering and drug delivery. However, most existing gels lack functional groups that can be modified with biomolecules that can guide cell/material interactions. We created an amine-functionalized ABA block copolymer, poly(ethylene glycol)-poly(serinol hexamethylene urethane), or ESHU. This reverse thermal gel consists of a hydrophobic block (B): poly(serinol hexamethylene urethane) and a hydrophilic block (A):...

  4. Non-ionic amphiphilic block copolymers by RAFT-polymerization and their self-organization

    OpenAIRE

    Garnier, Sébastien; Laschewsky, André

    2006-01-01

    Water-soluble, amphiphilic diblock copolymers were synthesized by reversible addition fragmentation chain transfer polymerization. They consist of poly(butyl acrylate) as hydrophobic block with a low glass transition temperature and three different nonionic water-soluble blocks, namely, the classical hydrophilic block poly(dimethylacrylamide), the strongly hydrophilic poly(acryloyloxyethyl methylsulfoxide), and the thermally sensitive poly(N-acryloylpyrrolidine). Aqueous micellar solutions of...

  5. Supramolecular Assemblies from Poly(styrene-block-poly(4-vinylpyridine Diblock Copolymers Mixed with 6-Hydroxy-2-naphthoic Acid

    Directory of Open Access Journals (Sweden)

    Jean-François Gohy

    2013-06-01

    Full Text Available Supramolecular assemblies involving interaction of a small organic molecule, 2-hydroxy-6-Naphthoic acid (HNA, with poly(styrene-block-poly(4-vinylpyridine (PS-b-P4VP diblock copolymers are utilized to obtain micellar structures in solution, nanostructured thin films on flat substrates and, finally, nanoporous thin films. The formation of hydrogen bonds between HNA and the poly(4-vinylpyridine (P4VP blocks is confirmed by spectroscopic measurements. The accordingly P4VP/HNA hydrogen-bonded complexes are poorly soluble in 1,4-dioxane, resulting in the formation of micellar structures with a P4VP/HNA core and a polystyrene (PS corona. Those micelles have been spin-coated onto silicon wafers, resulting in nanostructured thin films consisting of P4VP/HNA dot-like features embedded in a PS matrix. The morphology of those films has been tuned by solvent annealing. Selective dissolution of HNA by methanol results in the formation of a nanoporous thin film. The P4VP/HNA nanodomains have been also cross-linked by borax, and the thin films have been further dissolved in a good solvent for PS, leading to micelles with a structure reminiscent of the thin films.

  6. Lateral structuring and stability phenomena induced by block copolymers and core-shell nanogel particles at immiscible polymer/polymer interfaces

    Science.gov (United States)

    Gozen, Arif Omer

    We have investigated the parameters such as copolymer/nanoparticle concentration, architecture and molecular weight combined with film thickness, time and temperature in order to develop a molecular-level insight on how lateral interfacial structuring occurs at immiscible polymer/polymer interfaces. I order to develop a molecular-level understanding of how these 'smart' self-assembling materials and core-shell nanogel particles interact both intra- and inter-molecularly and form ordered structures in bulk, as well as at immiscible interfaces, we first focused on the response of core-shell polymer nanoparticles, designated CSNGs, composed of a cross-linked divinylbenzene core and poly(methyl methacrylate) (PMMA) arms as they segregate from PMMA homopolymer. We have demonstrated that these nanogel particles exhibit autophobic character when dispersed in high molecular weight homopolymer matrices and segregate to the interface with another fluid. We have further explored the migration of these new-generation nanogel particles (CSNG-Rs) segregating from PS homopolymer to PS/PMMA interfaces. Unlike the instability patterns observed with the CSNGs, which exhibit classical nucleation and growth mechanism with circular hole formation, we have observed an intriguing dewetting pattern and CSNG-Rs forming lateral aggregates and tentacle-like structures at the interface. In parallel with our core-shell particle studies, we have also explored the structuring of copolymer molecules that are far from equilibrium in bulk and complex laminate of polymer thin films. Our early triblock copolymer studies have proven that molecular asymmetry has a profound effect on order-disorder transition temperature. We focused primarily on the effect of the copolymer chemical composition (i.e., block sizes) on the dewetting behavior of PS/SM thin films on PMMA. We elucidate the interfacial segregation and concurrent micellization of diblock copolymers in a dynamically evolving environment with

  7. Synthesis of Dumbbell-shaped Hyperbranched Amphiphilic Block Copolymer by Controlled Atom Transfer Radical Polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Kim, In Kyoung; An, Sung Guk; Cho, Chang Gi [Center for Advanced Functional Polymers, Department of Fiber and Polymer Science, Hanyang University, Seoul (Korea); Noh, Si Tae [Department of Chemical Engineering, Hanyang University, Ansan (Korea)

    2001-04-01

    Amphiphilic block copolymers containing hydrophilic ethylene glycol core and hyperbranched polystyrene (PS) arm were synthesized by atom transfer radical polymerization using hydrophilic macroinitiator and p-chloromethyl styrene (CMS) as AB type monomer. Hydrophilic poly(ethylene glycol)(PEG) macroinitiators with difuntional groups were synthesized by reacting PEG and 2-bromopropionyl bromide. The chemical structure, molecular weight, and polydispersity index of the amphiphilic block copolymer were characterized by {sup 1}H-NMR spectroscopy and GPC analysis. The molecular weight increased as the reaction time increased. Polydispersity index of the obtained polymer was relatively narrow (below 1.39). To control chain density of the hyperbranched PS, styrene and CMS were copolymerized. It was found that amphiphilic block copolymer molecule underwent conformational change in different solvents based on the result for {sup 1}H-NMR spectroscopic analysis. 29 refs., 8 figs., 2 tabs.

  8. AMPHIPHILIC STAR-BLOCK COPOLYMERS BY IODIDE-MEDIATED RADICAL POLYMERIZATION

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Amphiphilic star-block copolymers composed of polystyrene and poly(acrylic acid) were synthesized by iodidemediated radical polymerization. Firstly, free radical polymerization of styrene was carried out with AIBN as initiator and 1,1,1-trimethyolpropane tri(2-iodoisobutyrate) as chain transfer agent, giving iodine atom ended star-shaped polystyrene with three arm chains, R(polystyrene)3. Secondly, tert-butyl acrylate was polymerization using polystyrene obtained as macro-chain transfer agent, and star-block copolymer, R(polystyrene-b-poly(tert-butyl acrylate))3 with controlled molecular weight was obtained. Finally, amphiphilic star-block copolymer, R(polystyrene-b-poly(acrylic acid))3 was obtained by hydrolysis of R(polystyrene-b-poly(tert-butyl acrylate))3 under acidic condition.

  9. Amphiphilic block copolymers in oil-water-surfactant mixtures: efficiency boosting, structure, phase behaviour and mechanism

    Science.gov (United States)

    Gompper, G.; Richter, D.; Strey, R.

    2001-10-01

    The effect of amphiphilic block copolymers on the phase behaviour and structure of ternary microemulsions in water, oil and non-ionic surfactant mixtures is reviewed. Recent experiments have revealed that the addition of small amounts of polyethylenepropylene-polyethyleneoxide block copolymer to the ternary systems leads to a dramatic increase in the volumes of oil and water solubilized into a bicontinuous microemulsion for a given surfactant volume fraction. While phase diagrams directly show the power of the amphiphilic block copolymers as efficiency boosters, the theoretical analysis in terms of bending energy discloses the mechanism for the efficiency boosting as due to the variation of the surfactant film curvature elasticity by tethered polymers in the form of mushrooms at the interface. Neutron scattering experiments employing a high-precision two-dimensional contrast variation technique confirm this picture and demonstrate that the polymer molecules uniformly decorate the surfactant film.

  10. Three-dimensional inverse design of nanopatterns with block copolymers and homopolymers

    Science.gov (United States)

    Xu, Dan; Liu, Hong; Zhu, You-Liang; Lu, Zhong-Yuan

    2016-02-01

    We propose a facile inverse design strategy to generate three-dimensional (3D) nanopatterns by using either block copolymers or a binary homopolymer blend via dissipative particle dynamics simulations. We find that the composition window of block copolymers to form a specific 3D morphology can be expanded when the self-assembly of block copolymers is directed by templates. We also find that a binary homopolymer blend can serve as a better candidate in the inverse templating design, since they have similar performances on recovering the target pattern, with much lower cost. This strategy is proved efficient for fabricating templates with desired topographical configuration, and the inverse design idea sheds lights on better control and design of materials with complex nanopatterns.

  11. Three-dimensional inverse design of nanopatterns with block copolymers and homopolymers.

    Science.gov (United States)

    Xu, Dan; Liu, Hong; Zhu, You-Liang; Lu, Zhong-Yuan

    2016-03-01

    We propose a facile inverse design strategy to generate three-dimensional (3D) nanopatterns by using either block copolymers or a binary homopolymer blend via dissipative particle dynamics simulations. We find that the composition window of block copolymers to form a specific 3D morphology can be expanded when the self-assembly of block copolymers is directed by templates. We also find that a binary homopolymer blend can serve as a better candidate in the inverse templating design, since they have similar performances on recovering the target pattern, with much lower cost. This strategy is proved efficient for fabricating templates with desired topographical configuration, and the inverse design idea sheds lights on better control and design of materials with complex nanopatterns. PMID:26880143

  12. Selective directed self-assembly of coexisting morphologies using block copolymer blends

    Science.gov (United States)

    Stein, A.; Wright, G.; Yager, K. G.; Doerk, G. S.; Black, C. T.

    2016-08-01

    Directed self-assembly (DSA) of block copolymers is an emergent technique for nano-lithography, but is limited in the range of structures possible in a single fabrication step. Here we expand on traditional DSA chemical patterning. A blend of lamellar- and cylinder-forming block copolymers assembles on specially designed surface chemical line gratings, leading to the simultaneous formation of coexisting ordered morphologies in separate areas of the substrate. The competing energetics of polymer chain distortions and chemical mismatch with the substrate grating bias the system towards either line/space or dot array patterns, depending on the pitch and linewidth of the prepattern. This is in contrast to the typical DSA, wherein assembly of a single-component block copolymer on chemical templates generates patterns of either lines/spaces (lamellar) or hexagonal dot arrays (cylinders). In our approach, the chemical template encodes desired local spatial arrangements of coexisting design motifs, self-assembled from a single, sophisticated resist.

  13. Micellization kinetics in block copolymer solutions : Scaling model

    NARCIS (Netherlands)

    Dormidontova, EE

    1999-01-01

    The kinetics of micelle evolution of diblock copolymers from unimers toward the equilibrium state is studied analytically on the basis of consideration of the kinetic equations. The association/dissociation rate constants for unimer insertion/expulsion and micelle fusion/fission are calculated by ap

  14. Collapse transitions in thermosensitive multi-block copolymers: A Monte Carlo study

    International Nuclear Information System (INIS)

    Monte Carlo simulations are performed on a simple cubic lattice to investigate the behavior of a single linear multiblock copolymer chain of various lengths N. The chain of type (AnBn)m consists of alternating A and B blocks, where A are solvophilic and B are solvophobic and N = 2nm. The conformations are classified in five cases of globule formation by the solvophobic blocks of the chain. The dependence of globule characteristics on the molecular weight and on the number of blocks, which participate in their formation, is examined. The focus is on relative high molecular weight blocks (i.e., N in the range of 500–5000 units) and very differing energetic conditions for the two blocks (very good—almost athermal solvent for A and bad solvent for B). A rich phase behavior is observed as a result of the alternating architecture of the multiblock copolymer chain. We trust that thermodynamic equilibrium has been reached for chains of N up to 2000 units; however, for longer chains kinetic entrapments are observed. The comparison among equivalent globules consisting of different number of B-blocks shows that the more the solvophobic blocks constituting the globule the bigger its radius of gyration and the looser its structure. Comparisons between globules formed by the solvophobic blocks of the multiblock copolymer chain and their homopolymer analogs highlight the important role of the solvophilic A-blocks

  15. Collapse transitions in thermosensitive multi-block copolymers: A Monte Carlo study

    Energy Technology Data Exchange (ETDEWEB)

    Rissanou, Anastassia N., E-mail: rissanou@tem.uoc.gr [Department of Mathematics and Applied Mathematics, University of Crete, GR-71003 Heraklion Crete, Greece and Archimedes Center for Analysis, Modeling and Computation, University of Crete, P.O. Box 2208, GR-71003 Heraklion Crete (Greece); Tzeli, Despoina S. [Department of Materials Science and Technology, University of Crete, GR-71003 Heraklion Crete (Greece); Anastasiadis, Spiros H. [Department of Chemistry, University of Crete, P.O. Box 2208, 710 03 Heraklion Crete (Greece); Institute of Electronic Structure and Laser, Foundation for Research and Technology-Hellas, GR-71110 Heraklion Crete (Greece); Bitsanis, Ioannis A. [Institute of Electronic Structure and Laser, Foundation for Research and Technology-Hellas, GR-71110 Heraklion Crete (Greece)

    2014-05-28

    Monte Carlo simulations are performed on a simple cubic lattice to investigate the behavior of a single linear multiblock copolymer chain of various lengths N. The chain of type (A{sub n}B{sub n}){sub m} consists of alternating A and B blocks, where A are solvophilic and B are solvophobic and N = 2nm. The conformations are classified in five cases of globule formation by the solvophobic blocks of the chain. The dependence of globule characteristics on the molecular weight and on the number of blocks, which participate in their formation, is examined. The focus is on relative high molecular weight blocks (i.e., N in the range of 500–5000 units) and very differing energetic conditions for the two blocks (very good—almost athermal solvent for A and bad solvent for B). A rich phase behavior is observed as a result of the alternating architecture of the multiblock copolymer chain. We trust that thermodynamic equilibrium has been reached for chains of N up to 2000 units; however, for longer chains kinetic entrapments are observed. The comparison among equivalent globules consisting of different number of B-blocks shows that the more the solvophobic blocks constituting the globule the bigger its radius of gyration and the looser its structure. Comparisons between globules formed by the solvophobic blocks of the multiblock copolymer chain and their homopolymer analogs highlight the important role of the solvophilic A-blocks.

  16. Formation of Nonclassical Ordered Phases of A B -Type Multiarm Block Copolymers

    Science.gov (United States)

    Gao, Ya; Deng, Hanlin; Li, Weihua; Qiu, Feng; Shi, An-Chang

    2016-02-01

    The formation of ordered phases from block copolymers is driven by a delicate balance between the monomer-monomer interaction and chain configurational entropy. The configurational entropy can be regulated by designed chain architecture, resulting in a new entropy-driven mechanism to control the self-assembly of ordered phases from block copolymers. An effective routine to regulate the configurational entropy is to utilize multiarm architecture, in which the entropic contribution to the free energy could be qualitatively controlled by the fraction of bridging configurations. As an illustration of this mechanism, the phase behavior of two A B -type multiarm block copolymers, B0-(Bi-Ai) m and (B1-Ai-B2) m where the minority A blocks form cylindrical or spherical domains, are examined using the self-consistent field theory (SCFT). The SCFT results demonstrate that the packing symmetry of the cylinders or spheres can be controlled by the length of the bridging B blocks. Several nonclassical ordered phases, including a novel square array cylinder with p 4 m m symmetry, are predicted to form from the A B -type multiarm block copolymers.

  17. Micelles, Lamellaes and Connected Bilayer Membranes in Block Copolymer Melts, Blends and Solutions

    Science.gov (United States)

    Mortensen, Kell

    1997-03-01

    Block copolymers of poly(ethylene oxide), PEO, and poly(propylene oxide), PPO, provide a unique model system for studies of aqueous systems of amphilic macromolecules, as the amphiphilic character can be changed continuously by changing temperature(K Mortensen, W Brown, B. Nordén , Phys. Rev. Letters 13 2340 (1992)) or pressure(K Mortensen, D Schwahn S Janssen Phys. Rev. Letters 71 1728 (1993)). The structural characteristics of aqueous solutions of the PEO-PPO-PEO copolymers and their self-associated assemblies are reviewed(K Mortensen, J. Phys. Cond. Matter 8 A103 (1996)). It is shown by small-angle neutron scattering that at low temperatures and/or concentration the individual copolymers exist in solution as individual unimers. Depending on molecular design, i.e. size of the individual blocks, various aggregates are formed, including spherical, worm-like and disc-shaped micelles. The spherical micelles provide the basis for liquid-crystalline mesophases of cubic structure. The crystallization can be understood as a simple hard-sphere condensation. Worm- or rod-like micelles may form nematic or hexagonally ordered structures, whereas the discs may condense into lamellar phases. While bi-continuous microemulsions frequently appear in ternary phase diagrams of oil, water and low-molecular surfactants, there has only recently been observations of such phases in binary systems of block copolymers and solvent. The first observation was made in an aqueous solution of a low PEO-content PEO-PPO-PEO triblock copolymer(E Hecht, K Mortensen, H Hoffmann, Macromolecules 28 5465, 1995). More recently, the microemulsion sponge phase has been observed in a system of tri-block copolymers dissolved in homopolymers( JH Laurer, JC Fung, JW Sedat, DA Agard, SD Schmit, J Samseth, K Mortensen, RJ Spontak, Langmuir, submitted) and in a ternary systems of diblock copolymer and homopolymers(FS Bates, WW Maurer, PM Lipic MA Hillmyer, KA Almdal, K Mortensen, TP Lodge Science, submitted).

  18. Synthesis of Dextran/Methoxy Poly(ethylene glycol) Block Copolymer

    OpenAIRE

    Young-Il Jeong; Dong-Gon Kim; Dae-Hwan Kang

    2013-01-01

    We synthesized a block copolymer composed of dextran and methoxy poly(ethylene glycol) (mPEG). To accomplish this, the end group of dextran was modified by reductive amination. The aminated dextran (Dextran-NH2) showed the intrinsic peaks of both dextran at 3~5.5 ppm and hexamethylene diamine at 1~2.6 ppm at 1H nuclear magnetic resonance (NMR) spectrum. The amino end group of dextran was conjugated with mPEG to make the block copolymer consisting of dextran/mPEG (abbre...

  19. ADVANCES IN MICROEMULSION PHASE ON SELF-ASSEMBLY AND MICELLE EXTRACTION WITH BLOCK COPOLYMERS

    Institute of Scientific and Technical Information of China (English)

    Chen Guo; Hao Wen; Huizhou Liu

    2005-01-01

    In this paper we review our work on self-assembly of the system, poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) block copolymers, which is a kind of macromolecular complex fluids. The control of self-assembly could be obtained by adding inorganic salts or aliphatic alcohols. By self-assembly of amphiphilic block copolymers, a microemulsion phase is formed, which could be applied in micelle extraction, such as hollow-fiber membrane micelle extraction, magnetic micelle extraction and immobilized micelle extraction.

  20. Data on macrophage mediated muscle transfection upon delivery of naked plasmid DNA with block copolymers.

    Science.gov (United States)

    Mahajan, Vivek; Gaymalov, Zagit; Alakhova, Daria; Gupta, Richa; Zucker, Irving H; Kabanov, Alexander V

    2016-06-01

    The data contains 14 figures supporting the research article "Horizontal gene transfer from macrophages to ischemic muscles upon delivery of naked DNA with Pluronic block copolymers" [1]. The data explains the surgical procedure and histological characterization of Murine Hind Limb Ischemia. The data also shows the kinetics of luciferase gene expression, spread of GFP expression through muscle and the colocalization of GFP with cellular markers in ischemic muscles injected with pDNA alone or pDNA/Pluronic. Finally the data shows the effect of Pluronic Block Copolymer to enhance total gene expression (cmv-promoter driven luciferase gene) in coculture of DNA transfected MØs with muscle cells. PMID:27222845

  1. Azidated Ether-Butadiene-Ether Block Copolymers as Binders for Solid Propellants

    Science.gov (United States)

    Cappello, Miriam; Lamia, Pietro; Mura, Claudio; Polacco, Giovanni; Filippi, Sara

    2016-07-01

    Polymeric binders for solid propellants are usually based on hydroxyl-terminated polybutadiene (HTPB), which does not contribute to the overall energy output. Azidic polyethers represent an interesting alternative but may have poorer mechanical properties. Polybutadiene-polyether copolymers may combine the advantages of both. Four different ether-butadiene-ether triblock copolymers were prepared and azidated starting from halogenated and/or tosylated monomers using HTPB as initiator. The presence of the butadiene block complicates the azidation step and reduces the storage stability of the azidic polymer. Nevertheless, the procedure allows modifying the binder properties by varying the type and lengths of the energetic blocks.

  2. Flow-directed block copolymer micelle morphologies via microfluidic self-assembly.

    Science.gov (United States)

    Wang, Chih-Wei; Sinton, David; Moffitt, Matthew G

    2011-11-23

    The self-assembly of amphiphilic block copolymers in a gas-liquid microfluidic reactor produces variable, flow-directed micellar morphologies entirely different from off-chip equilibrium structures. A polystyrene-block-poly(acrylic acid) copolymer, which forms exclusively spheres off-chip, generates kinetic cylinders, Y-junctions, bilayers, and networks by a mechanism of collision-coalescence enabled by strong and localized on-chip shear fields. Variation in the size and relative amount of flow-directed nanostructures is achieved by changing the water content and flow rate. These results demonstrate on-chip processing routes to specific functional colloidal nanostructures. PMID:21992654

  3. Enhancing relative permittivity by incorporating PDMS-PEG multi block copolymers in binary polymer blends

    DEFF Research Database (Denmark)

    A Razak, Aliff Hisyam; Szabo, Peter; Skov, Anne Ladegaard

    Polydimethylsiloxanes (PDMS) are well-known to actuate with relatively large strains due to low modulus, but they possess lowpermittivity. Contrary, polyethyleneglycols (PEG) are not stretchable but possess high permittivity. Combination of the two polymers in a block copolymer depicts a possibil......Polydimethylsiloxanes (PDMS) are well-known to actuate with relatively large strains due to low modulus, but they possess lowpermittivity. Contrary, polyethyleneglycols (PEG) are not stretchable but possess high permittivity. Combination of the two polymers in a block copolymer depicts a...

  4. Mesoscopic multiphase structures and the interfaces of block and graft copolymers in bulk

    International Nuclear Information System (INIS)

    Microphase-separated structures of copolymers with various architectures and their polymer/polymer interfaces were studied. They are SP diblock, PSP triblock, and SPP graft copolymers, where S and P denote polystyrene and poly(2-vinylpyridine), respectively. Morphological observations were carried out by means of transmission electron microscopy and small-angle X-ray scattering. Chain dimensions of component polymers were measured by small-angle neutron scattering and microphase-separated interfaces were observed by neutron reflectivity measurements using deuterium-labeled samples. It was clarified that morphological phase transitions among thermodynamically equilibrium structures for SP diblock and PSP triblock copolymers occur at almost the same compositions; however, those of SPP graft copolymers tend to occur at higher volume fraction of polystyrene, φs, than those for block copolymers. As for alternating lamellar structures it turned out to be clear that lamellar domain spacings, D's, were scaled as the 2/3 power of the molecular weight of polymers irrespective of their architectures. S block chains of SP diblock and PSP triblock copolymers in lamellar structures were both confirmed to be deformed toward the direction perpendicular to the lamellar interfaces, but it revealed that their volumes were preserved. Further, S/P interfacial thicknesses of SP and PSP were essentially the same to each other and the values defined as the FWHM of the error functions which express the segment density distributions of the interfaces were determined to be about 4 nm. (author)

  5. Analysis of the aggregation structure from amphiphilic block copolymers in solutions by small-angle x-ray scattering

    CERN Document Server

    Rong Li Xia; Wang Jun; Wei Liu He; Li Fu Mian; Li Zi Chen

    2002-01-01

    The aggregation structure of polystyrene-p vinyl benzoic amphiphilic block copolymers which were prepared in different conditions was investigated by synchrotron radiation small-angle x-ray scattering (SAXS). The micelle was self-assembled in selective solvents of the block copolymers. Authors' results demonstrate that the structure of the micelle depends on the factors, such as the composition of the copolymers, the nature of the solvent and the concentration of the solution

  6. Synthesis of Fluorinated Amphiphilic Block Copolymers Based on PEGMA, HEMA, and MMA via ATRP and CuAAC Click Chemistry

    OpenAIRE

    Fatime Eren Erol; Deniz Sinirlioglu; Sedat Cosgun; Ali Ekrem Muftuoglu

    2014-01-01

    Synthesis of fluorinated amphiphilic block copolymers via atom transfer radical polymerization (ATRP) and Cu(I) catalyzed Huisgen 1,3-dipolar cycloaddition (CuAAC) was demonstrated. First, a PEGMA and MMA based block copolymer carrying multiple side-chain acetylene moieties on the hydrophobic segment for postfunctionalization was carried out. This involves the synthesis of a series of P(HEMA-co-MMA) random copolymers to be employed as macroinitiators in the controlled synthesis of P(HEMA-co-M...

  7. Characterization of high performance randomly segmented poly(urethane siloxane) and poly(imide siloxane) block copolymers

    Science.gov (United States)

    Doǧan, Türkan; Baydoǧan, Nilgün; Köken, Nesrin

    2016-03-01

    Poly(imide siloxane) block copolymers with the same polydimethlysiloxane(APPS) were prepared by using 4,4'-oxydianiline (ODA) and Benzofenon-3,3,4,4-tetrakarboksilik dianhydride(BTDA) to compose the polyimide hard block. APPS and BTDA composed the polysiloxane soft block. The length of polysiloxane soft blocks increased with increasing the length of polyimide hard block. Copolymerization of soft and hard segments were determined by using this method. Copolymer structures could be obtained by holding constant hard block segments and by adjusting and increasing soft block segments. Thus, more flexible randomly segmented poly(imide siloxane) block copolymers can be obtained. These composed structure as flexible and high performance copolymers were characterized by FT-IR and evaluated. The structures were tested mechanically to detect their elastic recovery property as flexible material. The characterization of the samples enabled to examine flexible substrates in order to use in solar cell, aerospace applications and microelectronic devices.

  8. A simple pathway to ordered silica nanopattern from self-assembling of block copolymer containing organic silicon block

    International Nuclear Information System (INIS)

    Self-assembly of block copolymer is an effective strategy to prepare periodic structures at nanoscale. In this paper an unique and very simple method to prepare inorganic silica nanopattern is demonstrated from self-assembling of poly(styrene-block-dimethylsiloxane) (PS-b-PDMS) on the surface of silicon wafer. To simplify the patterning process, at first we obtain highly ordered PDMS microdomains, which are covered with PS layer by controlling solvent vapor annealing conditions. Following exposure to UV/O3 irradiation, nanopatterned surface consisting of silicon oxide is fabricated directly via selectively etching PS phase and converting PDMS phase into silicon oxide. As tuning the composition of the block copolymer, hexagonally packing dot and straight stripe pattern can be obtained. Finally, the time evolution from spheres morphology to aligned long cylinders is discussed. These results hold promise for nanolithography and the fabrication of nanodevices.

  9. Topcoat approaches for directed-assembly of copolymer films with blocks exhibiting differences in surface energy

    Science.gov (United States)

    Suh, Hyo Seon; in Lee, Jeong; Ramirez-Hernandez, Abelardo; Tada, Yasuhiko; Yoshida, Hiroshi; Wan, Lei; Ruiz, Ricardo; de Pablo, Juan; Nealey, Paul

    2013-03-01

    Fabricating patterns with feature dimensions smaller than 10 nm scale using block copolymer lithography requires the use of materials with large Flory-Huggins interaction parameters. Because such block copolymers (BCPs) typically show the large differences in surface energy between the blocks, one block (with lower surface energy) tends to segregate to the free surface of films and precludes the assembly of the desired through-film perpendicularly oriented structures. Here we describe a generalizable strategy to overcome this limitation. By coating the BCP film with an additional layer, a topcoat, thermodynamically favorable boundary conditions at the top surface of the film can be engineered for directed self-assembly. The allowable properties of the topcoats depend on the interfacial energies of the layer with the blocks of the copolymer, and the block-block interfacial energy. The strategy is demonstrated experimentally by directing the assembly of polystyrene-block-poly-2-vinylpyridine (PS- b-P2VP) films on chemically nanopatterned substrates with different topcoat materials.

  10. Living cationic polymerization and polyhomologation: an ideal combination to synthesize functionalized polyethylene–polyisobutylene block copolymers

    KAUST Repository

    Zhang, Hefeng

    2015-12-17

    A series of hydroxyl-terminated polyisobutylene-b-polyethylene (PIB-b-PE-OH) copolymers were synthesized by combining living cationic polymerization and polyhomologation. Allyl-terminated PIBs, synthesized by living cationic polymerization, were hydroborated with BH3·THF to produce 3-arm boron-linked stars, PIB3B, which served as macroinitiators for the in situ polyhomologation of dimethylsulfoxonium methylide. The resulting 3-arm star block copolymers, (PIB-b-PE)3B, were oxidized/hydrolysed to afford PIB-b-PE-OH. Characterization of all intermediates and final products by high temperature gel permeation chromatography (HT-GPC) and proton nuclear magnetic resonance spectroscopy (1H NMR) revealed the well-defined character of the copolymers. The thermal properties of the copolymers were studied by differential scanning calorimetry (DSC).

  11. Self-assembled structures of amphiphilic ionic block copolymers: Theory, self-consistent field modeling and experiment

    NARCIS (Netherlands)

    Borisov, O.V.; Zhulina, E.B.; Leermakers, F.A.M.; Muller, A.H.E.

    2011-01-01

    We present an overview of statistical thermodynamic theories that describe the self-assembly of amphiphilic ionic/hydrophobic diblock copolymers in dilute solution. Block copolymers with both strongly and weakly dissociating (pH-sensitive) ionic blocks are considered. We focus mostly on structural a

  12. Distributions of chain ends and junction points in ordered block copolymers

    International Nuclear Information System (INIS)

    Chain configurations in ordered symmetric poly(styrene-b-methyl methacrylate) diblock copolymers were examined by neutron reflectively. In a thin-film geometry the copolymers organize into lamellar microdomains oriented parallel to the substrate surface. The copolymers organize into lamellar microdomains oriented parallel to the substrate surface. The copolymers were synthesized with small fractions of deuterated segments at either the chain ends or centers. This selective labeling permitted characterization of the spatial distribution of chain ends and junction points normal to the plane of the film. From the reflectivity analysis, the junction points are found to be confined to the PS/PMMA interfacial regions. The chain ends, however, are well distributed through their respective domains, exhibiting only a weak maximum in concentration at the center of the domains

  13. Enantiomeric PLA-PEG block copolymers and their stereocomplex micelles used as rifampin delivery

    International Nuclear Information System (INIS)

    A novelty approach to self-assembling stereocomplex micelles by enantiomeric PLA-PEG block copolymers as a drug delivery carrier was described. The particles were encapsulated by enantiomeric PLA-PEG stereocomplex to form nanoscale micelles different from the microspheres or the single micelles by PLLA or PDLA in the reported literatures. First, the block copolymers of enantiomeric poly(l-lactide)-poly(ethylene-glycol) (PLLA-PEG) and poly(D-lactide)-poly(ethylene-glycol) (PDLA-PEG) were synthesized by the ring-opening polymerization of l-lactide and d-lactide in the presence of monomethoxy PEG, respectively. Second, the stereocomplex block copolymer micelles were obtained by the self-assembly of the equimolar mixtures of enantiomeric PLA-PEG copolymers in water. These micelles possessed partially the crystallized hydrophobic cores with the critical micelle concentrations (cmc) in the range of 0.8-4.8 mg/l and the mean hydrodynamic diameters ranging from 40 to 120 nm. The micelle sizes and cmc values obviously depended on the hydrophobic block PLA content in the copolymer. Compared with the single PLLA-PEG or PDLA-PEG micelles, the cmc values of the stereocomplex micelles became lower and the sizes of the stereocomplex micelles formed smaller. And lastly, the stereocomplex micelles encapsulated with rifampin were tested for the controlled release application. The rifampin loading capacity and encapsulation efficiency by the stereocomplex micelles were higher than those by the single polymer micelles, respectively. The drug release time in vitro was depending on the composites of the block copolymers and also could be controlled by the polymer molecular weight and the morphology of the polymer micelles

  14. Dissipative Particle Dynamics Simulation of Onion Phase in Star-block Copolymer

    Institute of Scientific and Technical Information of China (English)

    WU Shao-gui; DU Ting-ting

    2013-01-01

    A dissipative particle dynamics simulation technique was used to investigate the effect of molecular architecture of star-block copolymer on the patterned structure in a nanodroplet.With increasing the ratio of solvophilic to block length to solvophobic block length(RH/T),solvophobic sphere,ordered hexagonal phase,onion phase,perforated onion phase and flocculent phase are formed,respectively.Since onion phase has potential application in controlled drug release,it has received wide attention experimentally and theoretically.Our simulation indicates onion phase forms at a certain RH/T(close to but less than 1).A star-block copolymer molecule has two conformations in onion phase:either fully located in a shell or shared by two neighboring shells.Central structure affects onion's final shape.The molecular number of the copolymer in each shell is a quadratic function of the shell's radius.The arm number of star-block copolymer has little influence on onion's structure,but slightly affects the solvent content.Additionally,we studied the influence of arm length on onion's structure.

  15. The fabrication of highly ordered block copolymer micellar arrays: control of the separation distances of silicon oxide dots.

    Science.gov (United States)

    Yoo, Hana; Park, Soojin

    2010-06-18

    We demonstrate the fabrication of highly ordered silicon oxide dotted arrays prepared from polydimethylsiloxane (PDMS) filled nanoporous block copolymer (BCP) films and the preparation of nanoporous, flexible Teflon or polyimide films. Polystyrene-block-poly(2-vinylpyridine) (PS-b-P2VP) films were annealed in toluene vapor to enhance the lateral order of micellar arrays and were subsequently immersed in alcohol to produce nano-sized pores, which can be used as templates for filling a thin layer of PDMS. When a thin layer of PDMS was spin-coated onto nanoporous BCP films and thermally annealed at a certain temperature, the PDMS was drawn into the pores by capillary action. PDMS filled BCP templates were exposed to oxygen plasma environments in order to fabricate silicon oxide dotted arrays. By addition of PS homopolymer to PS-b-P2VP copolymer, the separation distances of micellar arrays were tuned. As-prepared silicon oxide dotted arrays were used as a hard master for fabricating nanoporous Teflon or polyimide films by spin-coating polymer precursor solutions onto silicon patterns and peeling off. This simple process enables us to fabricate highly ordered nanoporous BCP templates, silicon oxide dots, and flexible nanoporous polymer patterns with feature size of sub-20 nm over 5 cm x 5 cm. PMID:20498523

  16. Block copolymer modified surfaces for conjugation of biomacromolecules with control of quantity and activity.

    Science.gov (United States)

    Li, Xin; Wang, Mengmeng; Wang, Lei; Shi, Xiujuan; Xu, Yajun; Song, Bo; Chen, Hong

    2013-01-29

    Polymer brush layers based on block copolymers of poly(oligo(ethylene glycol) methacrylate) (POEGMA) and poly(glycidyl methacrylate) (PGMA) were formed on silicon wafers by activators generated by electron transfer atom transfer radical polymerization (AGET ATRP). Different types of biomolecule can be conjugated to these brush layers by reaction of PGMA epoxide groups with amino groups in the biomolecule, while POEGMA, which resists nonspecific protein adsorption, provides an antifouling environment. Surfaces were characterized by water contact angle, ellipsometry, and Fourier transform infrared spectroscopy (FTIR) to confirm the modification reactions. Phase segregation of the copolymer blocks in the layers was observed by AFM. The effect of surface properties on protein conjugation was investigated using radiolabeling methods. It was shown that surfaces with POEGMA layers were protein resistant, while the quantity of protein conjugated to the diblock copolymer modified surfaces increased with increasing PGMA layer thickness. The activity of lysozyme conjugated on the surface could also be controlled by varying the thickness of the copolymer layer. When biotin was conjugated to the block copolymer grafts, the surface remained resistant to nonspecific protein adsorption but showed specific binding of avidin. These properties, that is, well-controlled quantity and activity of conjugated biomolecules and specificity of interaction with target biomolecules may be exploited for the improvement of signal-to-noise ratio in sensor applications. More generally, such surfaces may be useful as biological recognition elements of high specificity for functional biomaterials. PMID:23265296

  17. Supramolecular block copolymers by kinetically controlled co-self-assembly of planar and core-twisted perylene bisimides

    Science.gov (United States)

    Görl, Daniel; Zhang, Xin; Stepanenko, Vladimir; Würthner, Frank

    2015-05-01

    New synthetic methodologies for the formation of block copolymers have revolutionized polymer science within the last two decades. However, the formation of supramolecular block copolymers composed of alternating sequences of larger block segments has not been realized yet. Here we show by transmission electron microscopy (TEM), 2D NMR and optical spectroscopy that two different perylene bisimide dyes bearing either a flat (A) or a twisted (B) core self-assemble in water into supramolecular block copolymers with an alternating sequence of (AmBB)n. The highly defined ultralong nanowire structure of these supramolecular copolymers is entirely different from those formed upon self-assembly of the individual counterparts, that is, stiff nanorods (A) and irregular nanoworms (B), respectively. Our studies further reveal that the as-formed supramolecular block copolymer constitutes a kinetic self-assembly product that transforms into thermodynamically more stable self-sorted homopolymers upon heating.

  18. Basic Research of Vibration Energy Harvesting Micro Device using Vinylidene Fluoride / Trifluoroethylene Copolymer Thin Film

    International Nuclear Information System (INIS)

    Basic research of MEMS based micro devices for vibration energy harvesting using vinylidene fluoride / trifluoroethylene (VDF/TrFE) copolymer thin film was investigated. The VDF/TrFE copolymer thin film was formed by spin coating. Thickness of VDF/TrFE copolymer thin film was ranged from 375 nm to 2793 nm. Impedance of VDF/TrFE copolymer thin film was measured by LCR meter. Thin film in each thickness was fully poled by voltage based on C-V characteristics result. Generated power of the devices under applied vibration was observed by an oscilloscope. When the film thickness is 2793 nm, the generated power was about 0.815 μJ

  19. Amphiphilic Fluorinated Block Copolymer Synthesized by RAFT Polymerization for Graphene Dispersions

    Directory of Open Access Journals (Sweden)

    Hyang Moo Lee

    2016-03-01

    Full Text Available Despite the superior properties of graphene, the strong π–π interactions among pristine graphenes yielding massive aggregation impede industrial applications. For non-covalent functionalization of highly-ordered pyrolytic graphite (HOPG, poly(2,2,2-trifluoroethyl methacrylate-block-poly(4-vinyl pyridine (PTFEMA-b-PVP block copolymers were prepared by reversible addition-fragmentation chain transfer (RAFT polymerization and used as polymeric dispersants in liquid phase exfoliation assisted by ultrasonication. The HOPG graphene concentrations were found to be 0.260–0.385 mg/mL in methanolic graphene dispersions stabilized with 10 wt % (relative to HOPG PTFEMA-b-PVP block copolymers after one week. Raman and atomic force microscopy (AFM analyses revealed that HOPG could not be completely exfoliated during the sonication. However, on-line turbidity results confirmed that the dispersion stability of HOPG in the presence of the block copolymer lasted for one week and that longer PTFEMA and PVP blocks led to better graphene dispersibility. Force–distance (F–d analyses of AFM showed that PVP block is a good graphene-philic block while PTFEMA is methanol-philic.

  20. Humidity-Induced Phase Transitions in Ion-Containing Block Copolymer Membranes

    Energy Technology Data Exchange (ETDEWEB)

    Park, Moon Jeong; Nedoma, Alisyn J.; Geissler, Phillip L.; Balsara, Nitash P.; Jackson, Andrew; Cookson, David (UCB); (NIST); (Aust. Synch.); (LBNL)

    2008-08-21

    The phase behavior of ion-containing block copolymer membranes in equilibrium with humidified air is studied as a function of the relative humidity (RH) of the surrounding air, ion content of the copolymer, and temperature. Increasing RH at constant temperature results in both disorder-to-order and order-to-order transitions. In-situ small-angle neutron scattering experiments on the open block copolymer system, when combined with water uptake measurement, indicate that the disorder-to-order transition is driven by an increase in the partial molar entropy of the water molecules in the ordered phase relative to that in the disordered phase. This is in contrast to most systems wherein increasing entropy results in stabilization of the disordered phase.

  1. Effects of copolymer composition, film thickness, and solvent vapor annealing time on dewetting of ultrathin block copolymer films.

    Science.gov (United States)

    Huang, Changchun; Wen, Gangyao; Li, Jingdan; Wu, Tao; Wang, Lina; Xue, Feifei; Li, Hongfei; Shi, Tongfei

    2016-09-15

    Effects of copolymer composition, film thickness, and solvent vapor annealing time on dewetting of spin-coated polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) films (annealed for different times were performed using X-ray photoelectron spectroscopy and contact angle measurement. With the annealing of acetone vapor, dewetting of the films with different thicknesses occur via the spinodal dewetting and the nucleation and growth mechanisms, respectively. The PS-b-PMMA films rupture into droplets which first coalesce into large ones to reduce the surface free energy. Then the large droplets rupture into small ones to increase the contact area between PMMA blocks and acetone molecules resulting from ultimate migration of PMMA blocks to droplet surface, which is a novel dewetting process observed in spin-coated films for the first time. PMID:27309943

  2. Synthesis of tri-block copolymers through reverse atom transfer radical polymerization of methyl methacrylate using polyurethane macroiniferter

    Directory of Open Access Journals (Sweden)

    2008-08-01

    Full Text Available Reverse atom transfer radical polymerization was successfully used for the first time to synthesis tri-block copolymers. Poly (methyl methacrylate-block-polyurethane-block-poly (methyl methacrylate tri-block copolymers were synthesized using tetraphenylethane-based polyurethane as a macroiniferter, copper(II halide as a catalyst and N, N, N′, N″, N″-pentamethyldiethylenetriamine as a ligand. Controlled nature of the polymerization was confirmed by the linear increase of number average molecular weight with increasing conversion. Mole contents of poly (methyl methacrylate present in the tri-block copolymers were calculated using proton nuclear magnetic resonance spectroscopy and the results were comparable with the gel permeation chromatography results. Differential scanning calorimetric results confirmed the presence of two different types of blocks in the tri-block copolymers.

  3. Block Copolymer Electrolytes: Thermodynamics, Ion Transport, and Use in Solid- State Lithium/Sulfur Cells

    Science.gov (United States)

    Teran, Alexander Andrew

    Nanostructured block copolymer electrolytes containing an ion-conducting block and a modulus-strengthening block are of interest for applications in solid-state lithium metal batteries. These materials can self-assemble into well-defined microstructures, creating conducting channels that facilitate ion transport. The overall objective of this dissertation is to gain a better understanding of the behavior of salt-containing block copolymers, and evaluate their potential for use in solid-state lithium/sulfur batteries. Anionically synthesized polystyrene-b-poly(ethylene oxide) (SEO) copolymers doped with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt were used as a model system. This thesis investigates the model system on several levels: from fundamental thermodynamic studies to bulk characterization and finally device assembly and testing. First, the thermodynamics of neat and salt-containing block copolymers was studied. The addition of salt to these materials is necessary to make them conductive, however even small amounts of salt can have significant effects on their phase behavior, and consequently their iontransport and mechanical properties. As a result, the effect of salt addition on block copolymer thermodynamics has been the subject of significant interest over the last decade. A comprehensive study of the thermodynamics of block copolymer/salt mixtures over a wide range of molecular weights, compositions, salt concentrations and temperatures was conducted. Next, the effect of molecular weight on ion transport in both homopolymer and copolymer electrolytes were studied over a wide range of chain lengths. Homopolymer electrolytes show an inverse relationship between conductivity and chain length, with a plateau in the infinite molecular weight limit. This is due to the presence of two mechanisms of ion conduction in homopolymers; the first mechanism is a result of the segmental motion of the chains surrounding the salt ions, 2 creating a liquid

  4. SYNTHESIS AND CHARACTERIZATION OF NOVEL CHIRAL SMECTIC C(Sc*) PHASE SHISH-KEBAB TYPE LIQUID CRYSTALLINE BLOCK COPOLYMERS

    Institute of Scientific and Technical Information of China (English)

    Shi-jun Zheng; Zi-fa Li; Shu-yuan Zhang; Shao-kui Cao; Ming-sheng Tang; Qiu-jun Fen; Qi-feng Zhou

    1999-01-01

    A new series of chiral shish-kebab type liquid crystal block copolymers that form the smectic C(Sc*) phase was synthesized by solution polycondensation. The copolymers were characterized by GPC,DSC, TG, POM, X-ray diffraction and polarimeter. The copolymers 7 entered into liquid crystal phase when they were heated to their melting temperatures (Tm) and the copolymers 8 were in liquid crystal phase at room temperature with low viscosities. The smectic sanded texture or focal-conic texture were observed on POM.All the chiral block copolymers showed high optical activity. No racemization has happened. Temperaturevariable X-ray diffraction study together with POM and polarimetric analysis realized that they are chiral smectic C(Sc*) phase. Thus we offer in this report the first example of shish-kebab type liquid crystal block copolymers that form a chiral smectic C(Sc*) phase. The variation of melting and isotropization temperatures with molecular structure was also discussed.

  5. Synthesis of (meth)acrylate block copolymers by ligated anionic polymerization

    Czech Academy of Sciences Publication Activity Database

    Vlček, Petr; Čadová, Eva; Janata, Miroslav; Látalová, Petra; Toman, Luděk; Kříž, Jaroslav; Kurková, Dana

    Goa : International Union of Pure and Applied Chemistry, 2005. s. 20-21. [International Symposium on Ionic Polymerization. 23.10.2005-28.10.2005, Goa ] R&D Projects: GA MŠk 1P05ME753 Institutional research plan: CEZ:AV0Z40500505 Keywords : block copolymers * anionic polymerization * tert-alkoxides Subject RIV: CD - Macromolecular Chemistry

  6. Complexes of block copolymers in solution: a graph-theoretical approach

    NARCIS (Netherlands)

    Damme, van Ruud; Geurts, Bernard J.

    1989-01-01

    We determine the statistical properties of block copolymers in solution. These complexes are assumed to have the topological structure of connected graphs with “nonnested” loops and cycles. The generating function method is used to determine the number of topologically different complexes containing

  7. Biodegradable block-copolymer micelles:Synthesis, characterization and radiolabelling for biodistribution studies

    Czech Academy of Sciences Publication Activity Database

    Machová, Luďka; Malinova, V.; Nováková, K.; Lázníček, M.; Koňák, Čestmír; Rypáček, František

    Antalya : Ankara University, Tissue Engineering and Biomaterials Laboratory, 2002. s. P-36. [International Symposium on Biomedical Science and Technology BIOMED /9./. 19.09.2002-22.09.2002, Antalya ] R&D Projects: GA AV ČR IAA4050202 Keywords : amphiphilic block copolymers * micelle * PLA-PEO Subject RIV: CD - Macromolecular Chemistry

  8. Poly(dimethylsiloxane)-poly(ethyleneoxide)-heparin block copolymers. I. Synthesis and characterization

    NARCIS (Netherlands)

    Grainger, D.W.; Kim, S.W.; Feijen, J.

    1988-01-01

    Amphiphilic block copolymers containing poly(dimethylsiloxane), poly(ethylene oxide), and heparin (PDMS-PEO-Hep) have been prepared via a series of coupling reactions using functionalized prepolymers, diisocyanates, and derivatized heparins. All intermediate steps of the synthesis yield quantifiable

  9. Interfacial activity of styrene-butadiene block copolymers in low-density polyethylene/polystyrene blends

    Czech Academy of Sciences Publication Activity Database

    Fortelný, Ivan; Šlouf, Miroslav; Hlavatá, Drahomíra; Sikora, Antonín

    2006-01-01

    Roč. 13, 8-9 (2006), s. 783-799. ISSN 0927-6440 Institutional research plan: CEZ:AV0Z40500505 Keywords : compatibilization * polymer blends * block copolymers Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.788, year: 2006

  10. LEO resistant PI-B-PDMS block copolymer films for solar array applications

    NARCIS (Netherlands)

    Lonkhuyzen, H. van; Bongers, E.; Fischer, H.R.; Dingemans, T.J.; Semprimoschnig, C.

    2013-01-01

    Due to their low atomic oxygen erosion yields PI-b-PDMS block copolymer films have considerable potential for application onto space exposed surfaces of satellites in low earth orbit. On solar arrays these materials might be used as electrical electrical insulation film, flexprint outer layer, elect

  11. Water vapor and gas transport through a poly (butylene terephthalate) poly (ethylene oxide) block copolymer

    NARCIS (Netherlands)

    Metz, S.J.; Potreck, J.; Mulder, M.H.V.; Wessling, M.

    2002-01-01

    In this paper the transport behavior of water vapor and nitrogen in a poly(butylene terephthalate) poly (ethylene oxide) block copolymer is discussed. This polymer has a high solubility for water (300 cm3 (STP)/cm3 polymer at activity 0.9). A new permeation set up has been built to determine the wat

  12. Self-assembled Block Copolymers with Various Architectures Designed by ATRP

    DEFF Research Database (Denmark)

    Jankova Atanasova, Katja

    networks and demonstrate good Li+ complexation and conductivity. These make the materials a potential for solid electrolyte applications in Li+ ion batteries (4, 6). iii. Amphiphilic water soluble star block copolymers with a polyacrylic acid core form hydrogels at room temperature above concentration 22g...

  13. Synthesis of Dendritic-Linear Block Copolymers by Atom Transfer Radical Polymerization

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The dendritic polyarylether 2-bromoisobutyrate as the macromolecular initiator for the controlled free radical polymerization of styrene was investigated. The polymerization was carried out with CuBr/2,2′-bipyridine catalyst at 110℃. It is found that the hybrid dendritic-linear block copolymers possess well-defined molecular weights and low polydispersities.

  14. Self-assembly of POSS-containing block copolymers: fixing the hierarchical structure in networks

    Czech Academy of Sciences Publication Activity Database

    Matějka, Libor; Janata, Miroslav; Pleštil, Josef; Zhigunov, Alexander; Šlouf, Miroslav

    2014-01-01

    Roč. 55, č. 1 (2014), s. 126-136. ISSN 0032-3861 R&D Projects: GA ČR GAP108/12/1459 Grant ostatní: AV ČR(CZ) M200500903 Institutional support: RVO:61389013 Keywords : block copolymers * self-assembly * POSS Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.562, year: 2014

  15. Effect of Electric Field Alignment on Morphology and Ionic Conductivity of Polymerized Ionic Liquid Block Copolymers

    Science.gov (United States)

    Sharick, Sharon; Nykaza, Jacob; Elabd, Yossef A.; Winey, Karen I.

    2014-03-01

    Polymerized ionic liquid (PIL) block copolymers are appealing for numerous electrochemical applications, including solid polymer electrolyte membranes for batteries and anion exchange membranes for fuel cells. The extent to which the reduced segmental motion caused by the non-conducting polymer segments and grain boundaries between block copolymer microdomains are detrimental to ionic conductivity is unknown. Increased long-range morphological order and connectivity of PIL microdomains are key to understanding the ion transport mechanism and may improve the ionic conductivity of PIL block copolymers. The effect of electric field on the morphology and ionic conductivity of poly(styrene- b-1-[2-(methacryloyloxy)ethyl]-3-butylimidazolium-bis(trifluoromethanesulfonyl)imide)) (PS- b-PMEBIm-TFSI) will be discussed as a function of microdomain orientation. Electric field is used to increase the perpendicular orientation of ion-conducting pathways with respect to the electrodes. The morphology and ionic conductivity were characterized by small-angle X-ray scattering and electrochemical impedance spectroscopy, respectively. The ionic conductivity of unoriented and oriented block copolymers will be compared to the PIL homopolymer, PMEBIm-TFSI, using the Sax and Ottino model.

  16. DYNAMIC DENSITY-FUNCTIONAL THEORY FOR MICROPHASE SEPARATION KINETICS OF BLOCK-COPOLYMER MELTS

    NARCIS (Netherlands)

    FRAAIJE, JGEM

    1993-01-01

    In this paper, we describe a numerical method for the calculation of collective diffusion relaxation mechanisms in quenched block copolymer melts. The method entails the repeated calculation of two opposing fields-an external potential field U, conjugate to the density field rho, and an energetic in

  17. Compartmentalization in hybrid metallacarborane nanoparticles formed by block copolymers with star-like architecture

    Czech Academy of Sciences Publication Activity Database

    Ďorďovič, V.; Uchman, M.; Zhigunov, Alexander; Nykänen, A.; Ruokolainen, J.; Matějíček, P.

    2014-01-01

    Roč. 3, č. 11 (2014), s. 1151-1155. ISSN 2161-1653 R&D Projects: GA ČR(CZ) GA14-14608S Institutional support: RVO:61389013 Keywords : nanoparticles * block copolymers * star-like architecture Subject RIV: CD - Macromolecular Chemistry Impact factor: 5.764, year: 2014

  18. Self-assembled block copolymer membranes: From basic research to large-scale manufacturing

    KAUST Repository

    Nunes, Suzana Pereira

    2013-09-24

    Order and porosity of block copolymer membranes have been controlled by solution thermodynamics, self-assembly, and macrophase separation. We have demonstrated how the film manufacture with long-range order can be up-scaled with the use of conventional membrane production technology.

  19. Multiscale Control of Hierarchical Structure in Crystalline Block Copolymer Nanoparticles Using Microfluidics.

    Science.gov (United States)

    Bains, Aman; Cao, Yimeng; Moffitt, Matthew G

    2015-11-01

    Hierarchical semicrystalline block copolymer nanoparticles are produced in a segmented gas-liquid microfluidic reactor with top-down control of multiscale structural features, including nanoparticle morphologies, sizes, and internal crystallinities. Control of multiscale structure on disparate length scales by a single control variable (flow rate) enables tailoring of drug delivery nanoparticle function including release rates. PMID:26305569

  20. How the chemical structure influence the dynamics of association of amphiphilic block copolymers

    Czech Academy of Sciences Publication Activity Database

    Deniau-Lejeune, E.; Charbonneau, C.; Borisova, O.; Chassenieux, C.; Colombani, O.; Štěpánek, Petr; Borisov, O.

    Saint-Petersburg: Institute of Macromolecular Compounds RAS, 2014. s. 46. ISBN 978-5-98340-329-1. [International Symposium "Molecular Order and Mobility in Polymer Systems" /8./. 02.06.2014-06.06.2014, St. Petersburg] Institutional support: RVO:61389013 Keywords : block copolymer * nanoparticles Subject RIV: CD - Macromolecular Chemistry

  1. Block copolymer self-assembly and co-assembly : shape function and application

    NARCIS (Netherlands)

    Li, F.

    2009-01-01

    Amphiphilic block copolymers can, in selective solvents such as water, assemble into various shapes and architectures. Among those, polymer vesicles, polymer micelles and polymer fibers are very popular structures in current nanotechnology. These objects each have their own particular properties and

  2. Anionic polymerization and polyhomologation: An ideal combination to synthesize polyethylene-based block copolymers

    KAUST Repository

    Zhang, H.

    2013-08-07

    A novel one-pot methodology combining anionic polymerization and polyhomologation, through a "bridge" molecule (BF3OEt 2), was developed for the synthesis of polyethylene (PE)-based block copolymers. The anionically synthesized macroanion reacts with the "bridge" molecule to afford a 3-arm star (trimacromolecular borane) which serves as an initiator for the polyhomologation. 2013 The Royal Society of Chemistry.

  3. Star block-copolymers: Enzyme-inspired catalysts for oxidation of alcohols in water

    KAUST Repository

    Mugemana, Clement

    2014-01-01

    A number of fluorous amphiphilic star block-copolymers containing a tris(benzyltriazolylmethyl)amine motif have been prepared. These polymers assembled into well-defined nanostructures in water, and their mode of assembly could be controlled by changing the composition of the polymer. The polymers were used for enzyme-inspired catalysis of alcohol oxidation. This journal is © the Partner Organisations 2014.

  4. Lamellar Microdomains of Block-Copolymer-Based Ionic Supramolecules Exhibiting a Hierarchical Self-Assembly

    DEFF Research Database (Denmark)

    Ayoubi, Mehran Asad; Almdal, Kristoffer; Zhu, Kaizheng;

    2014-01-01

    Based on a parent diblock copolymer of poly(styrene)-b-poly(methacrylic acid), PS-b-PMAA, linear-b-amphiphilic comb (L-b-AC) ionic supramolecules [Soft Matter 2013, 9, 1540-1555] are synthesized in which the poly(methacrylate) backbone of the ionic supramolecular AC-block is neutralized by alkyl...

  5. Composition and solution properties of fluorinated block copolymers and their surface structures in the solid state

    Institute of Scientific and Technical Information of China (English)

    NI HuaGang; XUE DongWu; WANG XiaoFang; ZHANG Wei; WANG XinPing; SHEN ZhiQuan

    2009-01-01

    A series of diblock copolymers composed of methyl methacrylate and 2-perfluorooctylethyl methacry-late (PMMA144-b-PFMAn) with various PFMA block lengths were prepared by atom transfer radical po-lymerization (ATRP). The surface structures and properties of these polymers in the solid state and in solution were investigated using contact angle measurement, X-ray photoelectron spectroscopy (XPS), sum frequency generation (SFG) vibrational spectroscopy, surface tension and dynamic laser light scattering (DLS). It was found that with increasing PFMA block length, water and oil repellency de-creased, the ratio of F/C increased with increasing film depth, and the degree of ordered packing of the perfluoroalkyl side chains at the surface decreased. When the number of PFMA block units reached 10, PMMA segments were detected at the copolymer surface, which was attributed to the PFMA block length affecting molecular aggregation structure of the copolymer in the solution and the interfacial structure at the air/liquid interface, which in turn affects surface structure formation during solution solidification. The results suggest that copolymer solution properties play an important role in struc-ture formation on the solid surface.

  6. Wafer-Scale Nanopillars Derived from Block Copolymer Lithography for Surface-Enhanced Raman Spectroscopy

    DEFF Research Database (Denmark)

    Li, Tao; Wu, Kaiyu; Rindzevicius, Tomas;

    2016-01-01

    ). Direct silicon etching with high aspect ratio templated by the block copolymer mask is realized without any intermediate layer or external precursors. Uniquely, an atomic layer deposition (ALD)-assisted method is introduced to allow reversing of the morphology relative to the initial pattern. As a result...

  7. Modification of polylactide surfaces with PLA-b-PEO block copolymers deposited from selective solvents

    Czech Academy of Sciences Publication Activity Database

    Chánová, Eliška; Popelka, Štěpán; Machová, Luďka; Rypáček, František

    New Rochelle: Mary Ann Liebert, Inc, 2008. s. 881 R&D Projects: GA MŠk 1M0538; GA AV ČR(CZ) 1QS500110564 EU Projects: European Commission(XE) 500283 - EXPERTISSUES Institutional research pla n: CEZ:AV0Z40500505 Keywords : amphiphilic block copolymers * polylactide * drug delivery systems Subject RIV: CD - Macromolecular Chemistry

  8. Orientational control of block copolymer microdomains by sub-tesla magnetic fields

    Science.gov (United States)

    Gopinadhan, Manesh; Choo, Youngwoo; Feng, Xunda; Kawabata, Kohsuke; di, Xiaojun; Osuji, Chinedum

    Magnetic fields offer a versatile approach to controlling the orientation of block copolymer (BCP) microdomains during self-assembly. To date however, such control has required the imposition of large magnetic fields (>3T), necessitating the use of complex magnet systems - either superconducting or very large conventional resistive magnets. Here we demonstrate the ability to direct BCP self-assembly using considerably smaller fields (<1T) which are accessible using simple rare-earth permanent magnets. The low field alignment is enabled by the presence of small quantities of mesogenic species that are blended into, and co-assemble with the liquid crystalline (LC) mesophase of the side-chain LC BCP under study. In situ SAXS experiments reveal a pronounced dependence of the critical alignment field strength on the stoichiometry of the blend, and the ability to generate aligned microdomains with orientational distribution coefficients exceeding 0.95 at sub-1 T fields for appropriate stoichiometries. The alignment response overall can be rationalized in terms of increased mobility and grain size due to the presence of the mesogenic additive. We use a permanent magnet to fabricate films with aligned nanopores, and the utility of this approach to generate complex BCP microdomain patterns in thin films by local field screening are highlighted. NSF DMR-1410568 and DMR-0847534.

  9. Directed Assembly of Block Copolymer Ordering on Rough and Patterned Flexible Substrates

    Science.gov (United States)

    Hayirlioglu, Arzu; Kulkarni, Manish; Karim, Alamgir

    2013-03-01

    Directed self-assembly of block copolymer (BCP) thin film on flexible substrates has potential in fabrication of flexible electronic devices due to its nanometer scale pattern formation capability. We studied the BCP ordering properties of polystyrene-b-poly(methyl methacrylate) (PS-b-PMMA) films on a flexible substrate, where the PS-b-PMMA films are initially coated on a smooth poly(dimethylsiloxane) (PDMS) substrate, whose surface energy (SE) was tuned between (20-69) mJ/m2 by UV-ozone (UVO) exposure. This range of SE allows for controlled wettability and orientation of the BCP overlayer. Further, we replicated different patterned media and observed perpendicular lamellar BCP orientation and parallel cylindrical BCP orientation on patterned flexible PDMS in the wetting SE regime. Rough surface structures created by silica xerogels were replicated on PDMS. RMS roughness of the xerogels is tuned by controlling sol-gel catalyst concentration and aging time. Effect of the aspect ratio of the rough PDMS substrates on the orientation of BCP films was studied. Surface morphology of the BCP films was studied by optical microscopy and Atomic Force Microscope (AFM), while orientation of the film's interior was studied using Grazing-Incidence Small Angle X-ray Scattering (GISAXS)

  10. Nonlinear rheological behavior associated with structural transitions in block copolymer solutions via nonequilibrium molecular dynamics.

    Science.gov (United States)

    Rychkov, Igor; Yoshikawa, Kenichi

    2004-02-15

    The nonequilibrium molecular dynamics computer simulation method was used to study microsegregated block copolymer systems in a selective solvent under a shear flow field. Two polymer concentrations were considered, 0.3 and 0.4, corresponding to the body centered cubic spherical and hexagonal cylindrical zero-shear phases, respectively. As the shear rate increased, both systems exhibited two-stage shear thinning, a peak in the scalar pressure, and normal stress differences. Microscopic connections were investigated by calculating the gyration and bond orientation tensors and the interaction energies per particle. At high shear rates, polymer chains elongate and orient along the direction of shear, and this is accompanied by the breaking-up of domains. The structure-rheology relation was discussed with regard to the morphological changes reported in our last study for the same systems. In particular, the structurally relevant critical values of the shear rate were found to delimit different behaviors of the shear rate-dependencies obtained in this work. PMID:15268506

  11. Asymmetrical Self-assembly From Fluorinated and Sulfonated Block Copolymers in Aqueous Media

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xiaojun [ORNL; Hong, Kunlun [ORNL; Baskaran, Durairaj [University of Tennessee, Knoxville (UTK); Goswami, Monojoy [ORNL; Sumpter, Bobby G [ORNL; Mays, Jimmy [ORNL

    2011-01-01

    Block copolymers of fluorinated isoprene and partially sulfonated styrene form novel tapered rods and ribbon-like micelles in aqueous media due to a distribution of sulfonation sites and a large Flory-Huggins interaction parameter. A combination of microscopy, light scattering, and simulation demonstrates the presence of these unique nanostructures. This study sheds light on the micellization behavior of amphiphilic block polymers by revealing a new mechanism of self-assembly.

  12. Morphology-controlled growth of perylene derivative induced by double-hydrophilic block copolymers

    OpenAIRE

    Minghua Huang; Markus Antonietti; Helmut Cölfen

    2016-01-01

    Controlled growth of technically relevant perylene derivative 3, 4, 9, 10-perylenetetracarboxylic acid potassium salt (PTCAPS), with tuneable morpologies, has been successfully realized by a recrystallization method using a double-hydrophilic block copolymer poly (ethylene glycol)-block poly (ethyleneimine) (PEG-b-PEI) as the structure directing agent. The {001} faces of PTCAPS are most polar and adsorb the oppositively charged polymer additive PEG-b-PEI well by electrostatic attraction. By s...

  13. Bioinspired amphiphilic phosphate block copolymers as non-fluoride materials to prevent dental erosion

    OpenAIRE

    Lei, Yanda; Wang, Tongxin; Mitchell, James W; Zaidel, Lynette; Qiu, Jianhong; Kilpatrick-Liverman, LaTonya

    2014-01-01

    Inspired by the fact that certain natural proteins, e.g. casein phosphopeptide or amelogenin, are able to prevent tooth erosion (mineral loss) and to enhance tooth remineralization, a synthetic amphiphilic diblock copolymer, containing a hydrophilic methacryloyloxyethyl phosphate block (MOEP) and a hydrophobic methyl methacrylate block (MMA), was designed as a novel non-fluoride agent to prevent tooth erosion under acidic conditions. The structure of the polymer, synthesized by reversible add...

  14. Thermally sensitive block copolymer hydrogels in bulk and with decreased dimensions

    OpenAIRE

    Nykänen, Antti

    2013-01-01

    The research on stimuli-responsive polymers has increased rapidly during the last two decades. Poly(N-isopropylacrylamide) (PNIPAM) is one of the most studied thermally responsive polymer because its lower critical solution temperature (LCST) 32 ℃ is close to the ambient conditions. Below 32 ℃, PNIPAM is water soluble, but at temperatures above 32 ℃ the polymer phase separates from water. In this thesis, amphiphilic triblock copolymer polystyrene-block-poly(N-isopropylacrylamide)-block-polys...

  15. Ligand switch in photoinduced copper-mediated polymerization: synthesis of methacrylate-acrylate block copolymers

    OpenAIRE

    CHUANG, Ya-Mi; Wenn, Benjamin; Gielen, Sam; Ethirajan, Anitha; Junkers, Thomas

    2015-01-01

    The use of photo-induced copper-mediated radical polymerization (photoCMP) to synthesize mixed acrylate/methacrylate (methyl acrylate, MA and methyl methacrylate, MMA) block copolymers is investigated. Reactions in which only one type of ligand (Me6TREN) is used lead to unsuccessful outcomes of polymerization due to a mismatch in reactivity of the two monomers. A ligand exchange to PMDETA for methacrylate is required to obtain good block structures. Due to insufficient re-initiation of polyac...

  16. Amphiphilic Fluorinated Block Copolymer Synthesized by RAFT Polymerization for Graphene Dispersions

    OpenAIRE

    Hyang Moo Lee; Suguna Perumal; In Woo Cheong

    2016-01-01

    Despite the superior properties of graphene, the strong π–π interactions among pristine graphenes yielding massive aggregation impede industrial applications. For non-covalent functionalization of highly-ordered pyrolytic graphite (HOPG), poly(2,2,2-trifluoroethyl methacrylate)-block-poly(4-vinyl pyridine) (PTFEMA-b-PVP) block copolymers were prepared by reversible addition-fragmentation chain transfer (RAFT) polymerization and used as polymeric dispersants in liquid phase exfoliation assiste...

  17. Photoinitiated Crosslinking and Grafting of Methylmethacrylate Using N,N-Dimethyl Amino Functional Polystyrene Block Copolymers

    OpenAIRE

    MÜFTÜOĞLU, Ali Ekrem; YAĞCI, Yusuf; SE, Kazunori

    2004-01-01

    Monodisperse poly(N,N-dimethyl-4-vinylphenethylamine)-block-polystyrene was synthesized via anionic living polymerization carried out at -78 °C under a pressure of 10-6 torr using cumyl potassium as the initiator. Subsequent photoinduced radical polymerization of styrene through side chain-functional N,N-dimethyl amino groups yielded a crosslinked polymer and a brush type block-graft copolymer to a lesser extent. Upon irradiation at a wavelength of 350 nm, macroradicals were generate...

  18. Chirality in Block Copolymer Melts: Mesoscopic Helicity from Inter-Segment Twist

    OpenAIRE

    Zhao, Wei; Russell, Thomas P.; Grason, Gregory M.

    2012-01-01

    We study the effects of chirality at the segment scale on the thermodynamics of block copolymer melts using self consistent field theory. In linear diblock melts where segments of one block prefer a twisted, or cholesteric, texture, we show that melt assembly is critically sensitive to the ratio of random coil size to the preferred pitch of cholesteric twist. For weakly-chiral melts (large pitch), mesophases remain achiral, while below a critical value of pitch, two mesocopically chiral phase...

  19. Evaluation of Isoprene Chain Extension from PEO Macromolecular Chain Transfer Agents for the Preparation of Dual, Invertible Block Copolymer Nanoassemblies

    OpenAIRE

    Bartels, Jeremy W.; Cauët, Solène I.; Billings, Peter L.; Lin, Lily Yun; Zhu, Jiahua; Fidge, Christopher; Pochan, Darrin J.; Wooley, Karen L.

    2010-01-01

    Two RAFT-capable PEO macro-CTAs, 2 and 5 kDa, were prepared and used for the polymerization of isoprene which yielded well-defined block copolymers of varied lengths and compositions. GPC analysis of the PEO macro-CTAs and block copolymers showed remaining unreacted PEO macro-CTA. Mathematical deconvolution of the GPC chromatograms allowed for the estimation of the blocking efficiency, about 50% for the 5 kDa PEO macro-CTA and 64% for the 2 kDa CTA. Self assembly of the block copolymers in bo...

  20. Phase behavior of ABC-type triple-hydrophilic block copolymers in aqueous solutions.

    Science.gov (United States)

    Zheng, Lingfei; Wu, Jianqi; Wang, Zheng; Yin, Yuhua; Jiang, Run; Li, Baohui

    2016-07-01

    The phase behavior of symmetric ABC triple-hydrophilic triblock copolymers in concentrated aqueous solutions is investigated using a simulated annealing technique. Two typical cases, in which the hydrophilicity of the middle B-block is either stronger or weaker than that of the end A- and C-blocks, are studied. In these two cases, a variety of phase diagrams are constructed as a function of the volume fraction of the B-block and the copolymer concentration ([Formula: see text] for both non-frustrated and frustrated copolymers. Structures, such as two-color alternatingly packed cylinders or gyroid, and lamellae-in-lamellae etc. that do not occur in the melt system, are obtained in solutions. Rich phase transition sequences, especially re-entrant phase transitions involving complex continuous networks of alternating gyroid and alternating diamond are observed for a given copolymer with decreasing [Formula: see text] . The difference in hydrophilicity among different blocks can result in inhomogeneous distribution of solvent molecules in the morphology, and with the decrease of [Formula: see text] , the distribution of solvent molecules presents a non-monotonic variation. This results in a non-monotonic variation of the effective volume fraction of each domain with the decrease of [Formula: see text] , which induces the re-entrant phase transitions. The presence of a good solvent for all the blocks can cause changes in the effective segregation strengths between different blocks and also in chain conformations, hence can alter the bulk phases and results in the occurrence of new structures and phase transitions. Especially, structures having A-C interfaces or A-C mixed domains can be obtained even in the non-frustrated copolymer systems, and structures obtained in the frustrated systems may be similar to those obtained in the non-frustrated systems. The window of the alternating gyroid structures may occupy a large part of the phase diagram for non

  1. Time-resolved GISAXS and cryo-microscopy characterization of block copolymer membrane formation

    KAUST Repository

    Marques, Debora S.

    2014-03-01

    Time-resolved grazing-incidence small-angle X-ray scattering (GISAXS) and cryo-microscopy were used for the first time to understand the pore evolution by copolymer assembly, leading to the formation of isoporous membranes with exceptional porosity and regularity. The formation of copolymer micelle strings in solution (in DMF/DOX/THF and DMF/DOX) was confirmed by cryo field emission scanning electron microscopy (cryo-FESEM) with a distance of 72 nm between centers of micelles placed in different strings. SAXS measurement of block copolymer solutions in DMF/DOX indicated hexagonal assembly with micelle-to-micelle distance of 84-87 nm for 14-20 wt% copolymer solutions. GISAXS in-plane peaks were detected, revealing order close to hexagonal. The d-spacing corresponding to the first peak in this case was 100-130 nm (lattice constant 115-150 nm) for 17 wt% copolymer solutions evaporating up to 100 s. Time-resolved cryo-FESEM showed the formation of incipient pores on the film surface after 4 s copolymer solution casting with distances between void centers of 125 nm. © 2014 Elsevier Ltd. All rights reserved.

  2. Synthesis and applications of polystyrene-block-poly(N-vinyl-2-pyrrolidone copolymers

    Directory of Open Access Journals (Sweden)

    Marcelo Alexandre de Farias

    2016-02-01

    Full Text Available Abstract This work describes the synthesis and applications of amphiphilic polystyrene-block-poly(N-vinyl-2-pyrrolidone (PS-b-PVP copolymers as a silver and silica nanoparticle surface modification agent. The synthesis of PS-b-PVP was carried out using controlled/living radical polymerization techniques. The synthesis of the block copolymers was confirmed by gel permeation chromatography and hydrogen nuclear magnetic resonance, presenting a polydispersity index of around 1.4 and number average molecular weight ranging between 10,000-14,000 g mol-1. The PS-b-PVP copolymers were applied as a silver nanoparticle (AgNP stabilizing agent. These nanoparticles were produced by a single step and presented an 11 ± 1 nm diameter. Furthermore, the PS-b-PVP copolymers were also applied as a silica nanoparticle (SiO2NP surface modification agent. The SiO2NP were synthesized by the Stöber method presenting a 72 ± 9 nm diameter. The SiO2NP surface modification by adsorption of PS-b-PVP caused the formation of a 5 ± 1 nm thick polymeric layer, providing the SiO2NP with a hydrophobic surface character. The structural and chemical characteristics shown by PS-b-PVP copolymers highlights their versatility for several applications, such as: water-in-oil emulsifier, stabilizing or coupling agents between inorganic particles and polymeric matrices.

  3. Block copolymer micelle nanolithography on non-conductive substrates

    International Nuclear Information System (INIS)

    A new lithographic technique has been developed and applied to cell adhesion studies and electro-optical material development. Attachment of 6 nm Au particles, in periodic and non-periodic pattern, onto non-conductive substrates has been achieved. This was performed via a combination of diblock copolymer self-assembly and electron beam lithographic techniques. To optimize e-beam resolution on non-conductive materials, an additional carbon layer was thread-coated onto the substrates. This carbon coating and the diblock copolymer used in the self-assembly step were simultaneously removed by a final hydrogen plasma treatment to reveal Au nanodot patterns of unprecedented pattern quality. These optically transparent substrates (glass cover slips) were bio-functionalized via the Au-dot patterns to yield a platform for unique cell adhesion studies. The same Au-dot patterning technique was applied to sapphire substrates, which were subsequently employed to nucleate electro-optically active ZnO nanopost growth

  4. Theory for dynamical self arrest and gelation in microemulsions and the block copolymer systems

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Sangwook

    2005-05-01

    The main purpose of this work is to investigate the glassy behavior of microemulsions and block copolymers. The origin of glassy behavior in microemulsions and block copolymers is frustration due to a competition between short-range interaction and long range interaction. According to the charge frustrated Ising model, the competition between ferromagnetic interaction and antiferromagnetic interaction is the origin of frustration in microemulsions. The competition between entropic effects and stoichiometric constraints responsible for the formation of micelles in microemulsions can lead to the emergence of a self generated glassy behavior in these systems. In the block copolymer, the competition between the repulsive short range interaction between monomers in polymer chains and the long range interaction by chemical bonds can lead to the emergence of a self generated glassy behavior. The criteria for the fluctuation induced first order transition and our microemulsion and block copolymer glasses are essentially the same. Both are a consequence of the large phase space of low energy excitations (14) (62) (all states with momenta q which fulfill |q| = q{sub m}) and are of at the most a moderate supercooling of the liquid state is required. This is strongly supported by the observation in Ref. (14) that the metastable states which are first to appear at a fluctuation induced first order transition are the ones build by a superposition of large amplitude waves of wavenumber q{sub m}, but with random orientations and phases, i.e. just the ones which form the metastable states of our microemulsion and block copolymer glass. (38)

  5. Silk-collagen-like block copolymers with charged blocks : self-assembly into nanosized ribbons and macroscopic gels

    OpenAIRE

    Martens, A.A.

    2008-01-01

    The research described in this thesis concerns the design, biotechnological production, and physiochemical study of large water-soluble (monodisperse) protein triblock-copolymers with sequential blocks, some of which are positively or negatively charged and self-assemble in response to a change in pH or co-assemble in response to oppositely charged polyelectrolytes (including each other). Such molecules displaying controlled self-assembly may lead to new biocompatible nano-structured material...

  6. SYNTHESIS OF POLY(ETHYLENE TEREPHTHALATE)-POLYCAPROLACTONE BLOCK COPOLYMER BY DIRECT COPOLYMERIZATION

    Institute of Scientific and Technical Information of China (English)

    Shen-guo Wang; Kai Tang

    1999-01-01

    Poly(ethylene terephthalate)-polycaprolactone block copolymer (PCL-b-PET) is a polyester with improved biodegradability. In the present paper, a new direct copolymerization method of ε-caprolactone (ε-CL) and bishydroxyethylene terephthalate (BHET) in the presence of Ti(OBu)4 was proposed for the synthesis of PCL-b-PET. The PCL-b-PET copolymer was characterized by IR, GPC and 1H-NMR techniques, and the effects of synthesis conditions, such as temperature, reaction time and concentration of catalyst on the copolymerization were discussed.

  7. Reversible Micro- and Nano- Phase Programming of Anthraquinone Thermochromism Using Blended Block Copolymers.

    Science.gov (United States)

    Zhang, Yumiao; Lovell, Jonathan F

    2015-12-22

    Here, we present an approach to generate materials with programmable thermochromic transition temperatures (TTTs), based on the reversible microcrystallization of anthraquinone dyes with the assistance of blended Pluronic block copolymers. At temperatures above block copolymer critical micellization temperature (CMT), hydrophobic anthraquinone dyes, including Sudan blue II, were dispersed in copolymer micelles, whereas at lower temperature, the dyes formed microcrystals driven by dye-dye and dye-Pluronic molecular interactions. The crystallization process altered the optical properties of the dye with bathochromatic shifts detectable by eye and the thermochromic process was fully reversible. Not only could Pluronic reversibly incorporate the anthraquinone dyes into micelles at elevated temperatures, but it also modulated the crystallization process and resulting morphology of microcrystals via tuning the molecular interactions when the temperature was lowered. Crystal melting transition points (and TTTs) were in agreement with the CMTs, demonstrating that the thermochromism was dependent on block copolymer micellization. Thermochromism could be readily programmed over a broad range of temperatures by changing the CMT by using different types and concentrations of Pluronics and combinations thereof. PMID:26626998

  8. Synthesis and Characterization of Smart Block Copolymers for Biomineralization and Biomedical Applications

    Energy Technology Data Exchange (ETDEWEB)

    Kanapathipillai, Mathumai [Iowa State Univ., Ames, IA (United States)

    2008-01-01

    Self-assembly is a powerful tool in forming structures with nanoscale dimensions. Self-assembly of macromolecules provides an efficient and rapid pathway for the formation of structures from the nanometer to micrometer range that are difficult, if not impossible to obtain by conventional lithographic techniques [1]. Depending on the morphologies obtained (size, shape, periodicity, etc.) these self-assembled systems have already been applied or shown to be useful for a number of applications in nanotechnology [2], biomineralization [3, 4], drug delivery [5, 6] and gene therapy [7]. In this respect, amphiphilic block copolymers that self-organize in solution have been found to be very versatile [1]. In recent years, polymer-micellar systems have been designed that are adaptable to their environment and able to respond in a controlled manner to external stimuli. In short, synthesis of 'nanoscale objects' that exhibit 'stimulus-responsive' properties is a topic gathering momentum, because their behavior is reminiscent of that exhibited by proteins [8]. By integrating environmentally sensitive homopolymers into amphiphilic block copolymers, smart block copolymers with self assembled supramolecular structures that exhibit stimuli or environmentally responsive properties can be obtained [1]. Several synthetic polymers are known to have environmentally responsive properties. Changes in the physical, chemical or biochemical environment of these polymers results in modulation of the solubility or chain conformation of the polymer [9]. There are many common schemes of engineering stimuli responsive properties into materials [8, 9]. Polymers exhibiting lower critical solution temperature (LCST) are soluble in solvent below a specific temperature and phase separate from solvent above that temperature while polymers exhibiting upper critical solution temperatures (UCST) phase separate below a certain temperature. The solubility of polymers with ionizable

  9. Multiple ordered phases in a block copolymer melt

    DEFF Research Database (Denmark)

    Almdal, K.; Koppi, K.A.; Bates, F.S.;

    1992-01-01

    -order based on discontinuities in the SANS pattern symmetries and intensities and dynamic elastic moduli. At the lowest experimental temperatures the material exhibits a (rippled) lamellar phase. At intermediate temperatures two new ordered phases appear. Above the order-disorder transition temperature a......A poly(ethylenepropylene)-poly(ethylethylene) (PEP-PEE) diblock copolymer containing 65% by volume PEP was investigated using small-angle neutron scattering (SANS) and rheological measurements. Four distinct phases have been identified as a function of temperature: three ordered phases at low...... temperatures and a disordered phase at elevated temperatures. Evaluation of the ordered phases was facilitated by the introduction of long-range order using a shear-orientation technique. SANS data were acquired as a function of temperature for three specimen orientations corresponding to the principle...

  10. PVP-b-PEO block copolymers for stable aqueous and ethanolic graphene dispersions.

    Science.gov (United States)

    Perumal, Suguna; Park, Kyung Tae; Lee, Hyang Moo; Cheong, In Woo

    2016-02-15

    The ability to disperse pristine (unfunctionalized) graphene is important for various applications, coating, nanocomposites, and energy related systems. Herein we report that amphiphilic copolymers of poly(4-vinyl pyridine)-block-poly(ethylene oxide) (PVP-b-PEO) are able to disperse graphene with high concentrations about 2.6mg/mL via sonication and centrifugation. Ethanolic and aqueous highly-ordered pyrolytic graphite (HOPG) dispersions with block copolymers were prepared and they were compared with the dispersions stabilized by P-123 Pluronic® (P123) and poly(styrene)-block-poly(ethylene oxide) (PS-b-PEO) synthesized. Transmission electron microscopy, scanning electron microscopy, atomic force microscopy, X-ray diffraction, Raman and UV-visible spectroscopic studies confirmed that PVP-b-PEO block copolymers are better stabilizers for HOPG graphene than P123 and PS-b-PEO. X-ray photoelectron spectroscopy and force-distance (F-d) curve analyses revealed that the nitrogen of vinyl pyridine plays a vital role in better attractive interaction with surface of graphene sheet. Thermogravimetric analysis showed that larger amount of PVP-b-PEO was adsorbed onto graphene with longer poly(4-vinyl pyridine) (PVP) block length and in aqueous medium, respectively, and which was consistent with electrical conductivity decreases. This study presents the dispersion efficiency of graphene using PVP-b-PEO varies substantially depending on the lengths of their hydrophobic (PVP) domains. PMID:26606378

  11. Bioinspired amphiphilic phosphate block copolymers as non-fluoride materials to prevent dental erosion.

    Science.gov (United States)

    Lei, Yanda; Wang, Tongxin; Mitchell, James W; Zaidel, Lynette; Qiu, Jianhong; Kilpatrick-Liverman, LaTonya

    2014-01-01

    Inspired by the fact that certain natural proteins, e.g. casein phosphopeptide or amelogenin, are able to prevent tooth erosion (mineral loss) and to enhance tooth remineralization, a synthetic amphiphilic diblock copolymer, containing a hydrophilic methacryloyloxyethyl phosphate block (MOEP) and a hydrophobic methyl methacrylate block (MMA), was designed as a novel non-fluoride agent to prevent tooth erosion under acidic conditions. The structure of the polymer, synthesized by reversible addition-fragment transfer (RAFT) polymerization, was confirmed by gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), and nuclear magnetic resonance spectroscopy (NMR). While the hydrophilic PMOEP block within the amphiphilic block copolymer strongly binds to the enamel surface, the PMMA block forms a hydrophobic shell to prevent acid attack on tooth enamel, thus preventing/reducing acid erosion. The polymer treatment not only effectively decreased the mineral loss of hydroxyapatite (HAP) by 36-46% compared to the untreated control, but also protected the surface morphology of the enamel specimen following exposure to acid. Additionally, experimental results confirmed that low pH values and high polymer concentrations facilitate polymer binding. Thus, the preliminary data suggests that this new amphiphilic diblock copolymer has the potential to be used as a non-fluoride ingredient for mouth-rinse or toothpaste to prevent/reduce tooth erosion. PMID:25419457

  12. Nanostructure of self-assembled rod-coil block copolymer films for photovoltaic applications

    International Nuclear Information System (INIS)

    The nanostructures of a series of rod-coil block copolymers, designed for photovoltaic applications, are studied by atomic force microscopy and transmission electron microscopy. The copolymers are composed of a semiconducting poly-p-phenylenevinylene rod with (2'-ethyl)-hexyloxy side chains and a functionalized coil block of various length and flexibility. Both, as deposited and annealed block copolymer films were investigated. The results show that highly ordered structures are only obtained if the coil block is characterized by a glass transition temperature which is significantly lower than the melting temperature of the alkyl side chains. For this material a high molecular mobility and strong driving force for crystallization of the rigid block can be achieved simultaneously. For the smallest coil to rod length ratio, we found a lamellar morphology with perpendicularly oriented lamellae with respect to the substrate. Electron diffraction data show the presence of a periodical molecular arrangement with a characteristic distance of 0.94 nm that is attributed to the distance between conjugated chains separated by the layers of alkyl sidechains

  13. A Solution-Processable (Tetraaniline-b-Polyethylene Glycol)3 Star-Shaped Rod-Coil Block Copolymer with Enhanced Electrochromic Properties.

    Science.gov (United States)

    Cao, Linyu; Gong, Chen; Yang, Jiping

    2016-02-01

    A novel electroactive star-shaped rod-coil copolymer composed of a benzene core and three symmetrically positioned tetraaniline-b-poly(ethylene glycol) arms, (TAni-b-PEG)3 rod-coil block copolymer, is synthesized successfully and characterized using Fourier transform infrared spectroscopy (FTIR), UV-vis, (1)H NMR, and matrix-assisted laser desorption/ionization (MALDI) mass spectrometry. Uniform and high-quality (TAni-b-PEG)3 thin films onto indium tin oxide-coated glass surface are fabricated simply from its DMF solution. Resulting (TAni-b-PEG)3 copolymer thin films possess excellent electrochromic properties with a high optical contrast of 73.3%, superb coloration efficiency of 318.5 cm(2) C(-1) at 750 nm. Very short switching times, that is, 2.11 s and 2.14 s for coloring and bleaching times, respectively, are observed as well. The mechanism of these impressive electrochromic properties of (TAni-b-PEG)3 thin films possessed is proposed based on the atomic force microscopy investigation, star-shaped molecular geometry, synergetic electronic and ionic conductivity and amphiphilic self-assembly feature of (TAni-b-PEG)3 copolymer, which can self-assemble to form cylinder pattern consisting of quick pathways for electronic charges and ionic species, respectively. PMID:26663524

  14. Environment-induced self-assembly in phase separated block copolymer systems: A SANS investigation

    International Nuclear Information System (INIS)

    In this research, we examine the effect of non-selective solvent on the large-scale mesoscopic ordering in asymmetric block copolymers, poly(styrene-block-ethylene/butylene-block-styrene) (SEBS) using small angle neutron scattering technique (SANS). SANS measurements were carried out over a wide range of concentrations and temperatures. Evolution of the self-assembled phase morphology in such polymer with the thermodynamic selectivity of solvent, temperature and concentration has been discussed. Correlation between morphology and thermorheological behavior of the gels has also been established

  15. Self-assembling Behavior of Amphiphilic Copolymer Containing Cross-linked Hydrophilic Block in Ethanol

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The self-assembly behavior of the amphiphilic block copolymer poly( methyl methacrylate)-block-poly( lead dimethacrylate) (PMMA-b-PLDMA) with cross-linked hydrophilic block (PLDMA) in ethanol was investigated. The results show that the size and morphology of the resulting micelle or micellar aggregates are ascribed to the content of ethanol and the nature of the solvent mixture. PbS nanoparticles were formed in the micelle by in situ reaction with H2S gas. The morphology and size of the self-assembly objects were investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM).

  16. Hydrogen-bonded multilayers of micelles of a dually responsive dicationic block copolymer

    OpenAIRE

    Erel, İrem; Karahan, H. Enis; Demirel, A. Levent; Tuncer, Cansel; Bütün, Vural

    2012-01-01

    We report the fabrication of hydrogen-bonded multilayers of micelles of a dually responsive, dicationic block copolymer, poly[2-(N-morpholino)ethyl methacrylate-block-2-(diisopropylamino)ethyl methacrylate] (PMEMA-b-PDPA). By taking advantage of the difference in the hydrophilicity of PMEMA and PDPA blocks, micelles with a PMEMA-corona and a PDPA-core were obtained above pH 6.5 and were assembled layer-by-layer at the surface with tannic acid (TA) at pH 7.4 through hydrogen bonding interactio...

  17. Application of Block Copolymer in Three-Liquid-Phase Extraction System

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A novel three-liquid-phase extraction system (TES) composed of butyl acetate, block copolymer polyethylene oxide-polypropylene oxide-polyethylene oxide and ammonium sulphate aqueous solution [(NH4)2SO4] as top, middle, and bottom phase, respectively, has been developed. The copolymer recycling and partitioning behavior of penicillin V has been studied in this system. Results show that the copolymer could be purified and recycled and penicillin V of the filtrated ferment broth could be partitioned unevenly among the phases and purified in the top phase of this TES. About 90 wt.% of penicillin V could be distributed into the top phase around pH 2.5 and only less than 0.1 wt.% left in the bottom phase.

  18. Modular synthesis of a block copolymer with a cleavable linkage via “click” chemistry

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    A diblock copolymer poly(ethylene glycol)-block-polystyrene or PEG-b-PS with an olefinic double bond at the PEG and PS junction has been prepared by modular synthesis via"click"chemistry.This involved the synthesis of PS by atom transfer radical polymerization and the nucleophilic substitution of the terminal bromide group with azide to yield azide-terminated PS. PEG with an alkynyl terminal group was prepared from reacting carboxyl-end-functionalized PEG with 4-hydroxybut-2-enyl prop-2-ynyl succinate,which contained an alkynyl group as well as an olefin group.The PS and PEG polymers were linked via the 1,3-dipolar cycloaddition of the end azide and alkyne groups.The obtained copolymer was characterized by 1H NMR spectroscopy and size exclusion chromatography(SEC).SEC analysis indicated that the diblock copolymer produced could be readily cleaved by ozonolysis to regenerate the constituent homopolymers.

  19. Photoinduced optical anisotropy in azobenzene methacrylate block copolymers: Influence of molecular weight and irradiation conditions

    DEFF Research Database (Denmark)

    Gimeno, Sofia; Forcen, Patricia; Oriol, Luis;

    2009-01-01

    The photoinduced anisotropy in a series of azomethacrylate block copolymers with different Molecular weights and azo contents has been investigated under several irradiation conditions. Depending on molecular weight and composition, different microstructures (disordered, lamellar, spherical) appear...... the copolymers in which azobenzene units segregate to nano spheres and the lowest (and less stable) Delta n(N) values, appear in disordered systems not showing any defined microstructure. Besides, higher Delta n(N) is obtained in the copolymers with larger molecular weight of the poly (methyl......) and light power (from 100 to 500 mW/cm(2)) also influence the photoinduced response. Photoinduced Delta n(N) growth rate is faster when both temperature and irradiation power increase. Furthermore, birefringence is only induced at temperatures up to 90 degrees C, the maximum value being obtained at...

  20. Morphological Studies on Sn-O Coordination Driving Self-assembly of Well-defined Organotin-containing Block Copolymers

    Institute of Scientific and Technical Information of China (English)

    Jian Jiang; Wei Yan; Ling-yan Liu; Wei-xing Chang; Jing Li

    2014-01-01

    A tin-oxygen coordination driving self-assembly was developed in the block copolymers containing organotin,which were prepared by the radical addition-fraction transfer (RAFT) method and characterized by the gel-permeation chromatography (GPC) and 1H-NMR.And the self-assemblies of these block copolymers with various chain length ratios in the different concenaations in CHCl3 were stable according to the results of DLS and TEM.Additionally,it was also given an insight investigation on the regulation of self-assembly of the block copolymers by adding dibutyltin dichloride and a possible mechanism was proposed.

  1. Electrospinning of a functional perfluorinated block copolymer as a powerful route for imparting superhydrophobicity and corrosion resistance to aluminum substrates.

    Science.gov (United States)

    Grignard, Bruno; Vaillant, Alexandre; de Coninck, Joel; Piens, Marcel; Jonas, Alain M; Detrembleur, Christophe; Jerome, Christine

    2011-01-01

    Superhydrophobic aluminum surfaces with excellent corrosion resistance were successfully prepared by electrospinning of a novel fluorinated diblock copolymer solution. Micro- and nanostructuration of the diblock copolymer coating was obtained by electrospinning which proved to be an easy and cheap electrospinning technology to fabricate superhydrophobic coating. The diblock copolymer is made of poly(heptadecafluorodecylacrylate-co-acrylic acid) (PFDA-co-AA) random copolymer as the first block and polyacrylonitrile (PAN) as the second one. The fluorinated block promotes hydrophobicity to the surface by reducing the surface tension, while its carboxylic acid functions anchor the polymer film onto the aluminum surface after annealing at 130 °C. The PAN block of this copolymer insures the stability of the structuration of the surface during annealing, thanks to the infusible character of PAN. It is also demonstrated that the so-formed superhydrophobic coating shows good adhesion to aluminum surfaces, resulting in excellent corrosion resistance. PMID:21141949

  2. Preparation, Stability, and Bio-Compatability of Block Copolymer Vesicles

    Science.gov (United States)

    Discher, Dennis; Lee, James C.-M.; Bermudez, Harry; Bates, Frank; Discher, Bohdana

    2001-03-01

    Vesicles made completely from diblock copolymers polymersomes can be stably prepared by a wide range of techniques common to liposomes. Processes such as film rehydration, sonication, and extrusion can generate many micron giants as well as monodisperse, 100 nm vesicles of PEO-PEE (polyethyleneoxide polyethylethylene) or PEO PBD (polyethyleneoxide polybutadiene). These thick-walled vesicles of polymer can encapsulate macromolecules just as liposomes can, but, unlike many pure liposome systems, these polymersomes exhibit no in-surface thermal transitions and a sub-population even survive autoclaving. Suspension in blood plasma has no immediate ill-effect on vesicle stability, and neither adhesion nor stimulation of phagocytes are apparent when giant polymersomes are held in direct, protracted contact. Proliferating cells, in addition, are unaffected when cultured for an extended time with an excess of polymersomes, and several injections of 10 mg doses into rats show no ill-effect. The results are consistent with the steric stabilization that PEG-lipid can impart to liposomes, but the present single-component polymersomes are far more stable mechanically and are not limited by PEG driven micellization.

  3. Block Copolymer Modified Epoxy Amine System for Reactive Rotational Molding: Structures, Properties and Processability

    Science.gov (United States)

    Lecocq, Eva; Nony, Fabien; Tcharkhtchi, Abbas; Gérard, Jean-François

    2011-05-01

    Poly(styrene-butadiene-methylmethacrylate) (SBM) and poly(methylmethacrylate-butyle-acrylate-methylmethacrylate) (MAM) triblock copolymers have been dissolved in liquid DGEBA epoxy resin which is subsequently polymerized by meta-xylene diamine (MXDA) or Jeffamine EDR-148. A chemorheology study of these formulations by plate-plate rheology and by thermal analysis has allowed to conclude that the addition of these copolymer blocks improve the reactive rotational moulding processability without affecting the processing time. Indeed, it prevents the pooling of the formulation at the bottom of the mould and a too rapid build up of resin viscosity of these thermosetting systems. The morphology of the cured blends examined by scanning electron microscopy (SEM) shows an increase of fracture surface area and thereby a potential increase of the toughness with the modification of epoxy system. Dynamic mechanical spectroscopy (DMA) and opalescence of final material show that the block PMMA, initially miscible, is likely to induce phase separation from the epoxy-amine matrix. Thereby, the poor compatibilisation between the toughener and the matrix has a detrimental effect on the tensile mechanical properties. The compatibilisation has to be increased to improve in synergy the processability and the final properties of these block copolymer modified formulations. First attempts could be by adapting the length and ratio of each block.

  4. Micellar cathodes from self-assembled nitroxide-containing block copolymers in battery electrolytes.

    Science.gov (United States)

    Hauffman, Guillaume; Maguin, Quentin; Bourgeois, Jean-Pierre; Vlad, Alexandru; Gohy, Jean-François

    2014-01-01

    This contribution describes the synthesis of block copolymers containing electrochemically active blocks, their micellization, and finally their use as micellar cathodes in a lithium battery. The self-assembly of the synthesized poly(styrene)-block-poly(2,2,6,6-tetramethylpiperidinyloxy-4-yl methacrylate) (PS-b-PTMA) diblock copolymers is realized in a typical battery electrolyte made of 1 m lithium trifluoromethanesulfonate dissolved in a mixture of ethylene carbonate/diethyl carbonate/dimethyl carbonate(1:1:1, in volume). Dynamic light scattering and atomic force micro-scopy indicate the formation of well-defined spherical micelles with a PS core and a PTMA corona. The electrochemical properties of those micelles are further investigated. Cyclic voltammograms show a reversible redox reaction at 3.6 V (vs Li(+) /Li). The charge/discharge profiles indicate a flat and reversible plateau around 3.6 V (vs Li(+) /Li). Finally, the cycling performances of the micellar cathodes are demonstrated. Such self-assembled block copolymers open new opportunities for nanostructured organic radical batteries. PMID:24127365

  5. Temperature and anion responsive self-assembly of ionic liquid block copolymers coating gold nanoparticles

    Science.gov (United States)

    Li, Junbo; Zhao, Jianlong; Wu, Wenlan; Liang, Ju; Guo, Jinwu; Zhou, Huiyun; Liang, Lijuan

    2016-06-01

    In this paper, double hydrophilic ionic liquid block copolymers (ILBCs), poly poly[1-methyl-3-(2-methacryloyloxy propylimidazolium bromine)]- block-(N-isopropylacrylamide) (PMMPImB- b-PNIPAAm) was first synthesized by reversible additionfragmentation chain transfer (RAFT) and then attached on the surface of gold nanoparticles (Au NPs) via a strong gold-sulfur bonding for preparing hybrid nanoparticles (PMMPImB- b-PNIPAAm-@-Au NPs). The hybrid NPs had a three layers micelle-like structure, including a gold core, thermo-responsive inner shell and anion responsive outer corona. The self-assembling behavior of thermal- and anion-response from shell and corona were respectively investigated by change of temperature and addition of (CF3SO2)2N-. The results showed the hybrid NPs retained a stable dispersion beyond the lower critical solution temperature (LCST) because of the space or electrostatic protecting by outer PMMPImB. However, with increasing concentration of (CF3SO2)2N-, the micellization of self-assembling PMMPImB- b-PNIPAAm-@-Au NPs was induced to form micellar structure containing the core with hydrophobic PMMPImB-(CF3SO2)2N- surrounded by composite shell of Au NPs-PNIPAAm via the anionresponsive properties of ILBCs. These results indicated that the block copolymers protected plasmonic nanoparticles remain self-assembling properties of block copolymers when phase transition from outer corona polymer.

  6. Colloidal ionic assembly between anionic native cellulose nanofibrils and cationic block copolymer micelles into biomimetic nanocomposites.

    Science.gov (United States)

    Wang, Miao; Olszewska, Anna; Walther, Andreas; Malho, Jani-Markus; Schacher, Felix H; Ruokolainen, Janne; Ankerfors, Mikael; Laine, Janne; Berglund, Lars A; Osterberg, Monika; Ikkala, Olli

    2011-06-13

    We present a facile ionic assembly between fibrillar and spherical colloidal objects toward biomimetic nanocomposites with majority hard and minority soft domains based on anionic reinforcing native cellulose nanofibrils and cationic amphiphilic block copolymer micelles with rubbery core. The concept is based on ionic complexation of carboxymethylated nanofibrillated cellulose (NFC, or also denoted as microfibrillated cellulose, MFC) and micelles formed by aqueous self-assembly of quaternized poly(1,2-butadiene)-block-poly(dimethylaminoethyl methacrylate) with high fraction of the NFC reinforcement. The adsorption of block copolymer micelles onto nanocellulose is shown by quartz crystal microbalance measurements, atomic force microscopy imaging, and fluorescent optical microscopy. The physical properties are elucidated using electron microscopy, thermal analysis, and mechanical testing. The cationic part of the block copolymer serves as a binder to NFC, whereas the hydrophobic rubbery micellar cores are designed to facilitate energy dissipation and nanoscale lubrication between the NFC domains under deformation. We show that the mechanical properties do not follow the rule of mixtures, and synergistic effects are observed with promoted work of fracture in one composition. As the concept allows wide possibilities for tuning, the work suggests pathways for nanocellulose-based biomimetic nanocomposites combining high toughness with stiffness and strength. PMID:21517114

  7. Temperature and anion responsive self-assembly of ionic liquid block copolymers coating gold nanoparticles

    Science.gov (United States)

    Li, Junbo; Zhao, Jianlong; Wu, Wenlan; Liang, Ju; Guo, Jinwu; Zhou, Huiyun; Liang, Lijuan

    2016-04-01

    In this paper, double hydrophilic ionic liquid block copolymers (ILBCs), poly poly[1-methyl-3-(2-methacryloyloxy propylimidazolium bromine)]-block-(N-isopropylacrylamide) (PMMPImB-b-PNIPAAm) was first synthesized by reversible additionfragmentation chain transfer (RAFT) and then attached on the surface of gold nanoparticles (Au NPs) via a strong gold-sulfur bonding for preparing hybrid nanoparticles (PMMPImB-b-PNIPAAm-@-Au NPs). The hybrid NPs had a three layers micelle-like structure, including a gold core, thermo-responsive inner shell and anion responsive outer corona. The self-assembling behavior of thermal- and anion-response from shell and corona were respectively investigated by change of temperature and addition of (CF3SO2)2N-. The results showed the hybrid NPs retained a stable dispersion beyond the lower critical solution temperature (LCST) because of the space or electrostatic protecting by outer PMMPImB. However, with increasing concentration of (CF3SO2)2N-, the micellization of self-assembling PMMPImB-b-PNIPAAm-@-Au NPs was induced to form micellar structure containing the core with hydrophobic PMMPImB- (CF3SO2)2N- surrounded by composite shell of Au NPs-PNIPAAm via the anionresponsive properties of ILBCs. These results indicated that the block copolymers protected plasmonic nanoparticles remain self-assembling properties of block copolymers when phase transition from outer corona polymer.

  8. Ionic Conductivity and Gas Permeability of Polymerized Ionic Liquid Block Copolymer Membranes

    Science.gov (United States)

    Evans, Christopher; Sanoja, Gabriel; Schneider, Yanika; Modestino, Miguel; Segalman, Rachel; Joint CenterArtificial Photosynthesis Team

    2014-03-01

    Polymer membranes for many energy applications, such as solar-to-hydrogen fuel production, require ionic conductivity while acting as gas diffusion barriers. We have synthesized a diblock copolymer consisting of poly(styrene-block-(4-(2-methacrylamidoethyl)-imidazolium trifluoroacetate) by treating poly(styrene-block-histamine methacrylamide) (PS- b-PHMA) with trifluoroacetic acid. The PS block serves as the structural support while the imidazolium derivative is an ion conducting polymerized ionic liquid (PIL). Small angle X-ray scattering and transmission electron microscopy demonstrate that the block copolymer self-assembles into well-ordered nanostructures, with lamellae and hexagonally packed cylindrical morphologies. The ionic conductivities of the PS-b-PHMA materials were as high as 2 x 10-4 S/cm while an order of magnitude increase in conductivity was observed upon conversion to PS-b-PIL. The ionic conductivity of the PS-b-PIL increased by a factor of ~ 4 up to 1.2 x 10-3 S/cm as the PIL domain size increased from 20 to 40 nm. These insights allow for the rational design of high performance ion conducting membranes with even greater conductivities via precise morphological control. Additionally, the role of thermal annealing on the ionic conductivity and gas permeability of copolymer membranes was investigated.

  9. Fluctuations, conformational asymmetry and block copolymer phase behaviour

    DEFF Research Database (Denmark)

    Bates, F.S.; Schulz, M.F.; Khandpur, A.K.;

    1994-01-01

    parameter and degree of polymerization, respectively. epsilon accounts for differences in the conformational and volume-filling characteristics of each block. Conformational asymmetry, epsilon not equal 1, produces an asymmetric phase diagram around f = 1/2. The importance of fluctuation effects are...

  10. Diblock copolymers comprising poly(2-vinylpyridine-co-acrylonitrile) and polystyrene blocks by nitroxide-mediated radical polymerization

    Czech Academy of Sciences Publication Activity Database

    Lokaj, Jan; Poláková, Lenka; Holler, Petr; Starovoytova, Larisa; Štěpánek, Petr; Diat, O.

    Prague : Institute of Macromolecular Chemistry AS CR, 2006. s. 41. [SONS Networking Activity Workshop: Structure and properties of self-organized amphiphilic copolymers. 04.10.2006-07.10.2006, Prague] R&D Projects: GA ČR GESON/03/E001 Keywords : block copolymers * nitroxide-mediated radical polymerization * 2-vinylpyridine Subject RIV: CD - Macromolecular Chemistry

  11. Block Copolymers of Ethylene Oxide and Styrene Oxide:New Copolymer Surfactants(Ⅰ)

    Institute of Scientific and Technical Information of China (English)

    Zhuo Yang; David Attwood; Colin Booth

    2003-01-01

    @@ 1 Introduction The range and application, actual and potential, of water-soluble block-copoly (oxyalkylene)s have beenextensively reviewed in recent compilations by edited by Nace[1] and by Alexandridis and Lindman[2].

  12. Self-assembly of diblock copolymer-maghemite nanoparticle hybrid thin films.

    Science.gov (United States)

    Yao, Yuan; Metwalli, Ezzeldin; Moulin, Jean-François; Su, Bo; Opel, Matthias; Müller-Buschbaum, Peter

    2014-10-22

    The arrangement of maghemite (γ-Fe2O3) nanoparticles (NPs) in poly(styrene-d8-block-n-butyl methacrylate) P(Sd-b-BMA) diblock copolymer (DBC) films via a self-assembly process was investigated toward the fabrication of highly ordered maghemite-polymer hybrid thin films. The resulting thin films exhibited a perforated lamella with an enrichment layer containing NPs as investigated with X-ray reflectometry, scanning electron microscopy, atomic force microscopy, and time-of-flight grazing incidence small angle neutron scattering as a function of the NP concentrations. The NPs were selectively deposited in the PSd domains of the DBC during the microphase separation process. At low NP concentrations, the incorporation of the NPs within the DBC thin films resulted in an enhanced microphase separation process and formation of highly oriented and ordered nanostructured hybrid films. At higher NP concentrations, the aggregation of the NPs was dominating and large sized metal oxide clusters were observed. The superparamagnetic properties of the metal oxide-polymer hybrid films at various NP concentrations were probed by a superconducting quantum interference device magnetometer, which shows that the hybrid films are highly attractive for optical devices, magnetic sensors, and magnetic recording devices. PMID:25243575

  13. Fast & scalable pattern transfer via block copolymer nanolithography

    DEFF Research Database (Denmark)

    Li, Tao; Wang, Zhongli; Schulte, Lars;

    2015-01-01

    solutions with selective solvents relative to the majority block. The pattern is directly formed during spin-casting at room temperature, which takes less than 20 seconds, without any preliminary surface treatment of the substrate and without any subsequent annealing. The self-assembled BCPs are transformed...... relying on long range lateral order, including fabrication of substrates for catalysis, solar cells, sensors, ultrafiltration membranes and templating of semiconductors or metals....

  14. Thermal Analysis, Structural Studies and Morphology of Spider Silk-like Block Copolymers

    Science.gov (United States)

    Huang, Wenwen

    Spider silk is a remarkable natural block copolymer, which offers a unique combination of low density, excellent mechanical properties, and thermal stability over a wide range of temperature, along with biocompatibility and biodegrability. The dragline silk of Nephila clavipes, is one of the most well understood and the best characterized spider silk, in which alanine-rich hydrophobic blocks and glycine-rich hydrophilic blocks are linked together generating a functional block copolymer with potential uses in biomedical applications such as guided tissue repair and drug delivery. To provide further insight into the relationships among peptide amino acid sequence, block length, and physical properties, in this thesis, we studied synthetic proteins inspired by the genetic sequences found in spider dragline silks, and used these bioengineered spider silk block copolymers to study thermal, structural and morphological features. To obtain a fuller understanding of the thermal dynamic properties of these novel materials, we use a model to calculate the heat capacity of spider silk block copolymer in the solid or liquid state, below or above the glass transition temperature, respectively. We characterize the thermal phase transitions by temperature modulated differential scanning calorimetry (TMDSC) and thermogravimetric analysis (TGA). We also determined the crystallinity by TMDSC and compared the result with Fourier transform infrared spectroscopy (FTIR) and wide angle X-ray diffraction (WAXD). To understand the protein-water interactions with respect to the protein amino acid sequence, we also modeled the specific reversing heat capacity of the protein-water system, Cp(T), based on the vibrational, rotational and translational motions of protein amino acid residues and water molecules. Advanced thermal analysis methods using TMDSC and TGA show two glass transitions were observed in all samples during heating. The low temperature glass transition, Tg(1), is related to

  15. Computational Investigation of Block Copolymer Surfactants for Stabilizing Fluctuation-Induced Polymeric Microemulsions

    Science.gov (United States)

    Delaney, Kris; Fredrickson, Glenn

    2013-03-01

    High molecular weight diblock copolymers introduced into a blend of immiscible homopolymers can act as a surfactant to suppress macroscopic two-fluid phase separation. With variation of block copolymer composition, the crossover between low-temperature ordering into microphase or macrophase separated states is marked by a mean-field isotropic Lifshitz multi-critical point. Strong fluctuations close to the Lifshitz point are observed to suppress the low-temperature ordering; a microemulsion state emerges, with large, co-continuous domains of segregated fluid lacking any long-range order. We study this phenomenon with fully fluctuating field-theoretic simulations based on complex Langevin sampling, and we attempt to design new block polymer surfactants that can produce the microemulsion state with a wider composition tolerance.

  16. Preparation and properties of proton conducting blending polymers with fluorous block copolymers as compatibilizers

    Energy Technology Data Exchange (ETDEWEB)

    Shi, K. [National Research Council of Canada, Vancouver, BC (Canada). Inst. for Fuel Cell Innovation; Murphy, J.; Sieb, N.; Holdcroft, S. [Simon Fraser Univ., Burnaby, BC (Canada). Dept. of Chemistry]|[National Research Council of Canada, Vancouver, BC (Canada). Inst. for Fuel Cell Innovation

    2005-07-01

    This paper presented the results of an experiment in which 3 series of membranes were prepared by blending polyvinylidene difluoride (PVDF) or poly(vinylidene difluoride-co-hexafluoropropylene) (P(VDF/HFP)) with sulfonated poly(ether ether ketone) (S-PEEK), sulfonated polysulfone (SPU), or sulfonated polystyrene in order to develop novel Proton Exchange Membranes (PEMs) suitable for melt processing. The incorporation of fluorine-containing block copolymer into the blended system resulted in the preparation of acceptable proton conductivity and low water containing PEM materials. The effect of sulfonated poly([vinylidene difluoride-co-hexafluoropropylene]-b-styrene block copolymers as compatibilizers was also investigated. It was observed that conductivity was enhanced for S-PEEK/fluoropolymer blends. Microstructures for the blends were examined by transmission electron microscope and scanning electron microscope.

  17. Functionalization of carbon nanofibers with elastomeric block copolymer using carbodiimide chemistry

    International Nuclear Information System (INIS)

    Surface functionalization of carbon nanofibers (CNFs) with aminopropyl terminated polydimethylsiloxane [(PDMS-NH2)] and other organic diamines was achieved using carbodiimide chemistry. The carbodiimide chemistry provides faster reaction rate so that the reaction occurs at lower temperature compared to amidation and acylation-amidation chemistry. CNF functionalized with PDMS-NH2 fibers were further functionalized with oligomer of polyimide (6FDA-BisP) using imidization reaction. The formation of block copolymer on the surface of CNF is proposed as an effective method to engineer the interphase between the fiber and the polymer, which is essential to modulate and enhance the properties of the nanocomposite. The efficiency of the carbodiimide chemistry to functionalize amine terminated groups on CNF and the functionalization of block copolymer was characterized using thermal gravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and UV-vis spectroscopy.

  18. Thermally induced structural evolution and performance of mesoporous block copolymer-directed alumina perovskite solar cells.

    KAUST Repository

    Tan, Kwan Wee

    2014-04-11

    Structure control in solution-processed hybrid perovskites is crucial to design and fabricate highly efficient solar cells. Here, we utilize in situ grazing incidence wide-angle X-ray scattering and scanning electron microscopy to investigate the structural evolution and film morphologies of methylammonium lead tri-iodide/chloride (CH3NH3PbI(3-x)Cl(x)) in mesoporous block copolymer derived alumina superstructures during thermal annealing. We show the CH3NH3PbI(3-x)Cl(x) material evolution to be characterized by three distinct structures: a crystalline precursor structure not described previously, a 3D perovskite structure, and a mixture of compounds resulting from degradation. Finally, we demonstrate how understanding the processing parameters provides the foundation needed for optimal perovskite film morphology and coverage, leading to enhanced block copolymer-directed perovskite solar cell performance.

  19. Structural and Mechanical Hysteresis at the Order-Order Transition of Block Copolymer Micellar Crystals

    Directory of Open Access Journals (Sweden)

    Theresa A. LaFollette

    2011-01-01

    Full Text Available Concentrated solutions of a water-soluble block copolymer (PEO20-(PPO70-(PEO20 show a thermoreversible transition from a liquid to a gel. Over a range of concentration there also exists an order-order transition (OOT between cubically-packed spherical micelles and hexagonally-packed cylindrical micelles. This OOT displays a hysteresis between the heating and cooling transitions that is observed at both the macroscale through rheology and nanoscale through small angle neutron scattering (SANS. The hysteresis is caused by the persistence of the cubically-packed spherical micelle phase into the hexagonally-packed cylindrical micelle phase likely due to the hindered realignment of the spherical micelles into cylindrical micelles and then packing of the cylindrical micelles into a hexagonally-packed cylindrical micelle phase. This type of hysteresis must be fully characterized, and possibly avoided, for these block copolymer systems to be used as templates in nanocomposites.

  20. Filtration on block copolymer solution used in directed self assembly lithography

    Science.gov (United States)

    Umeda, Toru; Takakura, Tomoyuki; Tsuzuki, Shuichi

    2016-03-01

    In this paper, we presented the filtration effects on block copolymers (BCP) that are commonly used in directed self-assembly lithographic (DSAL) imaging schemes. Specifically we focused on filtration effects on micro-contaminants such as metal ions and metal induced gels. Gel removal efficiency studies carried out with HDPE, Nylon and PTFE filters pointed out that Nylon 6,6 membrane is the most effective in removing gels in block copolymer (BCP) solutions. Metal removal efficiency studies were conducted using multistep filtrations such as repetitive filtration of single membrane material and combination of different type of membranes. Results showed that a combination of Nylon-6,6 and ion-exchange filters is highly effective in reducing metals such as Li, Mg and Al to > 99.99% efficiency. The mechanism of metal removal efficiency is discussed in detail.

  1. Synthesis of manganese oxide supported on mesoporous titanium oxide: Influence of the block copolymer

    Science.gov (United States)

    Schmit, F.; Bois, L.; Chiriac, R.; Toche, F.; Chassagneux, F.; Besson, M.; Descorme, C.; Khrouz, L.

    2015-01-01

    Manganese oxides supported on mesoporous titanium oxides were synthesized via a sol-gel route using block copolymer self-assembly. The oxides were characterized by X-ray diffraction, infrared spectroscopy, thermal analyses, nitrogen adsorption/desorption, electron microscopy and electronic paramagnetic resonance. A mesoporous anatase containing amorphous manganese oxide particles could be obtained with a 0.2 Mn:Ti molar ratio. At higher manganese loading (0.5 Mn:Ti molar ratio), segregation of crystalline manganese oxide occurred. The influence of block copolymer and manganese salt on the oxide structure was discussed. The evolution of the textural and structural characteristics of the materials upon hydrothermal treatment was also investigated.

  2. Directed self-assembly of block copolymers for next generation nanolithography

    Directory of Open Access Journals (Sweden)

    Seong-Jun Jeong

    2013-12-01

    Full Text Available Directed self-assembly of block copolymers has received a great deal of research attention as a promising nanolithography to complement the intrinsic limitations of conventional photolithography. In this review, we highlight the recent progress in the development of the directed self-assembly process for practical utilization in semiconductor applications. Various advanced directed self-assembly approaches are examined, in which block copolymer self-assembly is synergistically integrated with conventional photolithography, such as ArF lithography or I-line lithography, via either epitaxial self-assembly or the graphoepitaxy principle. We focus on the practical advantages anticipated from directed self-assembly integration, such as pattern density multiplication, feature size uniformity improvement, line edge roughness reduction, as well as cost reduction. Additionally, a direction for future research on directed self-assembly is suggested with diverse potential applications.

  3. Micellar Self-Assembly of Block Copolymers for Fabrication of Nanostructured Membranes

    KAUST Repository

    Marques, Debora S.

    2013-11-01

    This research work examines the process of block copolymer membrane fabrication by self-assembly combined by non-solvent induced phase separation. Self-assembly takes place from the preparation of the primordial solution until the moment of immersion in a non-solvent bath. These mechanisms are driven thermodynamically but are limited by kinetic factors. It is shown in this work how the ordering of the assembly of micelles is improved by the solution parameters such as solvent quality and concentration of block copolymer. Order transitions are detected, yielding changes in the morphology. The evaporation of the solvents after casting is demonstrated to be essential to reach optimum membrane structure. The non-solvent bath stops the phase separation at an optimum evaporation time.

  4. Block copolymer with simultaneous electric and ionic conduction for use in lithium ion batteries

    Science.gov (United States)

    Javier, Anna Esmeralda K; Balsara, Nitash Pervez; Patel, Shrayesh Naran; Hallinan, Jr., Daniel T

    2013-10-08

    Redox reactions that occur at the electrodes of batteries require transport of both ions and electrons to the active centers. Reported is the synthesis of a block copolymer that exhibits simultaneous electronic and ionic conduction. A combination of Grignard metathesis polymerization and click reaction was used successively to synthesize the block copolymer containing regioregular poly(3-hexylthiophene) (P3HT) and poly(ethylene oxide) (PEO) segments. The P3HT-PEO/LiTFSI mixture was then used to make a lithium battery cathode with LiFePO.sub.4 as the only other component. All-solid lithium batteries of the cathode described above, a solid electrolyte and a lithium foil as the anode showed capacities within experimental error of the theoretical capacity of the battery. The ability of P3HT-PEO to serve all of the transport and binding functions required in a lithium battery electrode is thus demonstrated.

  5. Laser Writing Block Copolymer Self-Assembly on Graphene Light-Absorbing Layer.

    Science.gov (United States)

    Jin, Hyeong Min; Lee, Seung Hyun; Kim, Ju Young; Son, Seung-Woo; Kim, Bong Hoon; Lee, Hwan Keon; Mun, Jeong Ho; Cha, Seung Keun; Kim, Jun Soo; Nealey, Paul F; Lee, Keon Jae; Kim, Sang Ouk

    2016-03-22

    Recent advance of high-power laser processing allows for rapid, continuous, area-selective material fabrication, typically represented by laser crystallization of silicon or oxides for display applications. Two-dimensional materials such as graphene exhibit remarkable physical properties and are under intensive development for the manufacture of flexible devices. Here we demonstrate an area-selective ultrafast nanofabrication method using low intensity infrared or visible laser irradiation to direct the self-assembly of block copolymer films into highly ordered manufacturing-relevant architectures at the scale below 12 nm. The fundamental principles underlying this light-induced nanofabrication mechanism include the self-assembly of block copolymers to proceed across the disorder-order transition under large thermal gradients, and the use of chemically modified graphene films as a flexible and conformal light-absorbing layers for transparent, nonplanar, and mechanically flexible surfaces. PMID:26871736

  6. Advantages and limitations of density functional theory in block copolymer directed self-assembly

    Science.gov (United States)

    Liu, Jimmy; Laachi, Nabil; Delaney, Kris T.; Fredrickson, Glenn H.

    2015-03-01

    A major challenge in the application of block copolymer directed self-assembly (DSA) to advanced lithography is the exploration of large design spaces, including the selection of confinement shape and size, surface chemistry to affect wetting conditions, copolymer chain length and block fraction. To sweep such large spaces, a computational model is ideally both fast and accurate. In this study, we investigate various incarnations of the density functional theory (DFT) approach and evaluate their suitability to DSA applications. We introduce a new optimization scheme to capitalize on the speed advantages of DFT, while minimizing loss of accuracy relative to the benchmark of self-consistent field theory (SCFT). Although current DFT models afford a 100-fold reduction in computational complexity over SCFT, even the best optimized models fail to match SCFT density profiles and make extremely poor predictions of commensurability windows and defect energetics. These limitations suggest that SCFT will remain the gold standard for DSA simulations in the near future.

  7. Amphiphilic block copolymers as efficiency boosters in microemulsions a SANS investigation of the role of polymers

    CERN Document Server

    Endo, H; Mihailescu, M; Monkenbusch, M; Gompper, G; Richter, D; Jakobs, B; Sottmann, T; Strey, R

    2002-01-01

    The effect of amphiphilic block copolymers on ternary microemulsions (water, oil and non-ionic surfactant) is investigated. Small amounts of PEP-PEO block copolymer lead to a dramatic expansion of the one-phase region where water and oil can be solubilized by the mediation of surfactant molecules. Small-angle neutron-scattering experiments employing a high-precision two-dimensional contrast-variation technique demonstrate that the polymer is distributed uniformly on the surfactant membrane, where it modifies the membrane curvature elasticity. Furthermore, a new approach to determine the bending rigidity of an amphiphilic membrane is proposed, which is precise enough to measure the logarithmic scale dependence of the bending rigidity and its universal prefactor in bicontinuous microemulsions. (orig.)

  8. The effect of random copolymer on the characteristic dimensions of cylinder-forming PS-b-PMMA thin films

    Energy Technology Data Exchange (ETDEWEB)

    Andreozzi, A; Poliani, E; Seguini, G; Perego, M, E-mail: andrea.andreozzi@mdm.imm.cnr.it [Laboratorio MDM, IMM-CNR, Via C Olivetti 2, 20864 Agrate Brianza (Italy)

    2011-05-06

    The block copolymer self-assembly approach has received great attention in recent years as a possible way to overcome the limits of conventional lithography and to fabricate sub-22 nm structures. At this level, precise nanometric control is crucial for technological applications and the search for a flexible and reproducible protocol is a great challenge. The polystyrene-b-poly(methylmethacrylate) (PS-b-PMMA) system, with a styrene fraction of 0.71, spontaneously separates into a periodic array of hexagonally packed PMMA cylinders embedded in a matrix of PS and, under suitable processing conditions, this is perpendicularly oriented with respect to the underlying substrate. The selective removal of the PMMA allows us to obtain a nanoporous PS matrix with well-defined pore dimensions. Perpendicular orientation of the PMMA cylinders requires surface neutralization by means of a suitable PS-r-PMMA random copolymer. The choice of the random copolymer is not trivial, because different PS-r-PMMA copolymers strongly affect the characteristics of the PS-b-PMMA film deposited on it. In this paper the effects of the selected PS-r-PMMA on the arrangement as well as on the peculiar dimensions (pore diameter, pore to pore distance) of the final nanoporous PS thin film are studied. Reliable protocols for the fabrication of a disposable polymeric mask are proposed in view of its application in advanced lithographic processes.

  9. The effect of random copolymer on the characteristic dimensions of cylinder-forming PS-b-PMMA thin films

    International Nuclear Information System (INIS)

    The block copolymer self-assembly approach has received great attention in recent years as a possible way to overcome the limits of conventional lithography and to fabricate sub-22 nm structures. At this level, precise nanometric control is crucial for technological applications and the search for a flexible and reproducible protocol is a great challenge. The polystyrene-b-poly(methylmethacrylate) (PS-b-PMMA) system, with a styrene fraction of 0.71, spontaneously separates into a periodic array of hexagonally packed PMMA cylinders embedded in a matrix of PS and, under suitable processing conditions, this is perpendicularly oriented with respect to the underlying substrate. The selective removal of the PMMA allows us to obtain a nanoporous PS matrix with well-defined pore dimensions. Perpendicular orientation of the PMMA cylinders requires surface neutralization by means of a suitable PS-r-PMMA random copolymer. The choice of the random copolymer is not trivial, because different PS-r-PMMA copolymers strongly affect the characteristics of the PS-b-PMMA film deposited on it. In this paper the effects of the selected PS-r-PMMA on the arrangement as well as on the peculiar dimensions (pore diameter, pore to pore distance) of the final nanoporous PS thin film are studied. Reliable protocols for the fabrication of a disposable polymeric mask are proposed in view of its application in advanced lithographic processes.

  10. Association and Structure of Thermo Sensitive Comblike Block Copolymers in Aqueous Solutions

    International Nuclear Information System (INIS)

    The structures and association properties of thermo sensitive poly(methoxyoligo(ethylene glycol) norbornenyl esters) block copolymers in D2O were investigated by Small Angle Neutron Scattering (SANS). Each block is a comb-like polymer with a polynorbornene (PNB) backbone and oligo ethylene glycol (OEG) side chains (one side chain per NB monomer). The chemical formula of the block copolymer is (OEG3NB)79-(OEG6.6NB)67, where subscripts represent the degree of polymerization (DP) of OEG and NB in each block The polymer concentration was fixed at 2.0 wt % and the structural changes were investigated over a temperature range between 25 C and 68 C. It was found that at room temperature polymers associate to form micelles with a spherical core formed by the block (OEG3NB)79 and corona formed by the block (OEG6.6NB)67 and that the shape of the polymer in the corona could be described by the form factor of rigid cylinders. At elevated temperatures, the aggregation number increases and the micelles become more compact. At temperatures round the cloud point temperature (CPT) T = 60 C a correlation peak started to appear and became pronounced at 68 C due to the formation of a partially ordered structure with a correlation length ∼ 349

  11. Structure-directing star-shaped block copolymers: supramolecular vesicles for the delivery of anticancer drugs.

    Science.gov (United States)

    Yang, Chuan; Liu, Shao Qiong; Venkataraman, Shrinivas; Gao, Shu Jun; Ke, Xiyu; Chia, Xin Tian; Hedrick, James L; Yang, Yi Yan

    2015-06-28

    Amphiphilic polycarbonate/PEG copolymer with a star-like architecture was designed to facilitate a unique supramolecular transformation of micelles to vesicles in aqueous solution for the efficient delivery of anticancer drugs. The star-shaped amphipilic block copolymer was synthesized by initiating the ring-opening polymerization of trimethylene carbonate (TMC) from methyl cholate through a combination of metal-free organo-catalytic living ring-opening polymerization and post-polymerization chain-end derivatization strategies. Subsequently, the self-assembly of the star-like polymer in aqueous solution into nanosized vesicles for anti-cancer drug delivery was studied. DOX was physically encapsulated into vesicles by dialysis and drug loading level was significant (22.5% in weight) for DOX. Importantly, DOX-loaded nanoparticles self-assembled from the star-like copolymer exhibited greater kinetic stability and higher DOX loading capacity than micelles prepared from cholesterol-initiated diblock analogue. The advantageous disparity is believed to be due to the transformation of micelles (diblock copolymer) to vesicles (star-like block copolymer) that possess greater core space for drug loading as well as the ability of such supramolecular structures to encapsulate DOX. DOX-loaded vesicles effectively inhibited the proliferation of 4T1, MDA-MB-231 and BT-474 cells, with IC50 values of 10, 1.5 and 1.0mg/L, respectively. DOX-loaded vesicles injected into 4T1 tumor-bearing mice exhibited enhanced accumulation in tumor tissue due to the enhanced permeation and retention (EPR) effect. Importantly, DOX-loaded vesicles demonstrated greater tumor growth inhibition than free DOX without causing significant body weight loss or cardiotoxicity. The unique ability of the star-like copolymer emanating from the methyl cholate core provided the requisite modification in the block copolymer interfacial curvature to generate vesicles of high loading capacity for DOX with significant

  12. Micelles and gels of oxyethylene-oxybutylene diblock copolymers in aqueous solution: The effect of oxyethylene-block length

    DEFF Research Database (Denmark)

    Derici, L.; Ledger, S.; Mai, S.M.;

    1999-01-01

    Block copolymer E(90)B(10) (E = oxyethylene, B = oxybutylene) was synthesised and characterised by gel permeation chromatography and (13)C NMR spectroscopy. Dynamic light scattering (DLS) and static light scattering (SLS) were used to characterise the micelles in solution (both in water and in...... of the E blocks occurred at high concentration (greater than or equal to 70 wt.% copolymer). By combining the present and published results, a comparison was made of the micelle and gel properties of copolymers with the same B-block length but different E-block lengths, i.e., E(90)B(10), E(40)B(10...... water in the micelle core. Moderately concentrated solutions of copolymer E(90)B(10) were studied in the gel state by small-angle X-ray scattering (SAXS) in tandem with rheology (oscillatory shear). Values for the dynamic elastic modulus (G') of the gels significantly exceeded 10(4) Pa across the range...

  13. Novel pH or thermosensitive block copolymers for triggered drug-delivery systems

    OpenAIRE

    Jérôme, Christine

    2007-01-01

    Over the last decade, polymer micelles and nanoparticles have attracted an increasing interest as efficient drug delivery systems. Polymer micelles from amphiphilic block copolymers are supramolecular core-shell type assemblies of some tens of nanometers in diameter. They are highly stable in aqueous solution because of their low intrinsic critical micelle concentration, which prevents their dissociation upon dilution in the blood stream after intravenous injection. The combination of poly(e...

  14. Synthetic routes toward functional block copolymers and bioconjugates via RAFT polymerization

    OpenAIRE

    Wiss, Kerstin T.

    2010-01-01

    Synthetic Routes toward Functional Block Copolymers and Bioconjugates via RAFT PolymerizationrnSynthesewege für funktionelle Blockcopolymere und Biohybride über RAFT PolymerisationrnDissertation von Dipl.-Chem. Kerstin T. WissrnIm Rahmen dieser Arbeit wurden effiziente Methoden für die Funktionalisierung beider Polymerkettenenden für Polymer- und Bioanbindung von Polymeren entwickelt, die mittels „Reversible Addition-Fragmentation Chain Transfer“ (RAFT) Polymerisation hergestellt wurden. Zu d...

  15. Synthesis of (meth)acrylate block copolymers by ligated anionic polymerization

    Czech Academy of Sciences Publication Activity Database

    Vlček, Petr; Čadová, Eva; Janata, Miroslav; Látalová, Petra; Toman, Luděk; Kříž, Jaroslav; Kurková, Dana

    2006-01-01

    Roč. 240, č. 1 (2006), s. 141-150. ISSN 1022-1360. [International Symposium on Ionic Polymerization. Goa, 23.10.2005-28.10.2005] R&D Projects: GA MŠk 1P05ME753 Institutional research plan: CEZ:AV0Z40500505 Keywords : anionic polymerization * block copolymers * ester-enolates Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.913, year: 2005

  16. Intracellular Trafficking of Polyamidoamine – Polyethylene Glycol Block Copolymers in DNA Delivery

    OpenAIRE

    Bonner, Daniel K.; Leung, Cheuk; Chen-Liang, Jane; Chingozha, Loice; Langer, Robert; Hammond, Paula T.

    2011-01-01

    The delivery of nucleic acids has the potential to revolutionize medicine by allowing previously untreatable diseases to be clinically addressed. Viral delivery systems have shown immunogenicity and toxicity dangers, but synthetic vectors have lagged in transfection efficiency. Previously, we have developed a modular, linear-dendritic block copolymer architecture with high gene transfection efficiency compared to commercial standards. This rationally designed system makes use of a cationic de...

  17. Poly(dimethylsiloxane)-poly(ethyleneoxide)-heparin block copolymers. I. Synthesis and characterization

    OpenAIRE

    D.W. Grainger; S. W. Kim; Feijen, J.

    1988-01-01

    Amphiphilic block copolymers containing poly(dimethylsiloxane), poly(ethylene oxide), and heparin (PDMS-PEO-Hep) have been prepared via a series of coupling reactions using functionalized prepolymers, diisocyanates, and derivatized heparins. All intermediate steps of the synthesis yield quantifiable products with reactive end-groups, while the final products demonstrate bioactive, covalently bound heparin moieties. Due to the solvent systems required, commercial sodium heparin was converted t...

  18. Block copolymer blends and solutions: from periodic nanostructures to bicontinuous micro-emulsions

    Czech Academy of Sciences Publication Activity Database

    Štěpánek, Petr; Tuzar, Zdeněk; Černoch, Peter; Nallet, F.; Diat, O.

    Stellenbosch : UNESCO Associated Centre for Macromolecules and Materials, University of Stellenbosch, 2005. Session 6, I. [Workshop on Advanced Materials (WAM III) focusing on Nanostructured Advanced Materials. 5.9.2005-8.9.2005, Stellenbosch] R&D Projects: GA ČR GESON/03/E001; GA AV ČR IAA4050403 Keywords : block copolymer films * nanostructures * light and neutron scattering Subject RIV: CD - Macromolecular Chemistry

  19. Phase diagram of selectively cross-linked block copolymers shows chemically microstructured gel

    OpenAIRE

    von der Heydt, Alice; Zippelius, Annette

    2014-01-01

    We study analytically the intricate phase behavior of cross-linked $AB$ diblock copolymer melts, which can undergo two main phase transitions due to quenched random constraints: Gelation, i.e., spatially random localization of polymers forming a system-spanning cluster, is driven by increasing the number parameter $\\mu$ of irreversible, type-selective cross-links between random pairs of $A$ blocks. Self-assembly into a periodic pattern of $A$/$B$-rich microdomains (microphase separation) is c...

  20. Tunable Mesoporous Bragg Reflectors Based on Block-Copolymer Self-Assembly

    OpenAIRE

    Guldin, S.; Kolle, M.; Stefik, M.; Langford, R; Eder, D.; Wiesner, U.; Steiner, U.

    2011-01-01

    Mesoporous Bragg reflectors are a promising materials platform for photovoltaics, light emission, and sensing. A fast and versatile fabrication route that relies on the self-assembly of the block copolymer poly(isoprene-b-ethylene oxide) in combination with simple sol-gel chemistry is reported. The method allows extended control over porosity and pore size in the resulting inorganic material and results in high-quality optical elements.

  1. Structural and Mechanical Hysteresis at the Order-Order Transition of Block Copolymer Micellar Crystals

    OpenAIRE

    LaFollette, Theresa A.; Lynn M. Walker Walker

    2011-01-01

    Concentrated solutions of a water-soluble block copolymer (PEO)20-(PPO)70-(PEO)20 show a thermoreversible transition from a liquid to a gel. Over a range of concentration there also exists an order-order transition (OOT) between cubically-packed spherical micelles and hexagonally-packed cylindrical micelles. This OOT displays a hysteresis between the heating and cooling transitions that is observed at both the macroscale through rheology and nanoscale through small angle neutron scattering (S...

  2. Aggregate of Amphiphilic Block Copolymer as a Pseudo-Stationary Phase in Capillary Electrophoresis

    OpenAIRE

    Nakamura, Tohru; OHKI, Akira; Mishiro, Masaki; Tsuyashima, Osamu; Maeda, Shigeru; ナカムラ, トオル; オオキ, アキラ; ミシロ, マサキ; ツヤシマ, オサム; マエダ, シゲル; 中村, 透; 大木, 章; 艶島, 修; 前田, 滋

    1999-01-01

    The use of an aggregate of amphiphilic block copolymer 1, which consists of poly[(N-acetylimino)ethylene] and poly[(N-pentanoylimino)ethylene], for a pseudo-stationary phase in capillary electrophoresis has been examined. From gel-filtration chromatography, the aggregate from 1 (1-AG) was found to incorporate phenol. When the running solution contains 1-AG and sodium dodecyl sulfate (SDS), the electrophoretic mobility becomes nearly zero. Thus, it is found that when 1-AG and SDS are added to ...

  3. Precise Control over the Rheological Behavior of Associating Stimuli-Responsive Block Copolymer Gels

    OpenAIRE

    Jérémy Brassinne; Flanco Zhuge; Charles-André Fustin; Jean-François Gohy

    2015-01-01

    “Smart” materials have considerably evolved over the last few years for specific applications. They rely on intelligent macromolecules or (supra-)molecular motifs to adapt their structure and properties in response to external triggers. Here, a supramolecular stimuli-responsive polymer gel is constructed from heterotelechelic double hydrophilic block copolymers that incorporate thermo-responsive sequences. These macromolecular building units are synthesized via a three-step controlled radical...

  4. Connecting Molecular Dynamics Simulations and Fluids Density Functional Theory of Block Copolymers

    Science.gov (United States)

    Hall, Lisa

    Increased understanding and precise control over the nanoscale structure and dynamics of microphase separated block copolymers would advance development of mechanically robust but conductive materials for battery electrolytes, among other applications. Both coarse-grained molecular dynamics (MD) simulations and fluids (classical) density functional theory (fDFT) can capture the microphase separation of block copolymers, using similar monomer-based chain models and including local packing effects. Equilibrium free energies of various microphases are readily accessible from fDFT, which allows us to efficiently determine the equilibrium nanostructure over a large parameter space. Meanwhile, MD allows us to visualize specific polymer conformations in 3D over time and to calculate dynamic properties. The fDFT density profiles are used to initialize the MD simulations; this ensures the MD proceeds in the appropriate microphase separated state rather than in a metastable structure (useful especially for nonlamellar structures). The simulations equilibrate more quickly than simulations initialized with a random state, which is significant especially for long chains. We apply these methods to study the interfacial behavior and microphase separated structure of diblock and tapered block copolymers. Tapered copolymers consist of pure A and B monomer blocks on the ends separated by a tapered region that smoothly varies from A to B (or from B to A for an inverse taper). Intuitively, tapering increases the segregation strength required for the material to microphase separate and increases the width of the interfacial region. Increasing normal taper length yields a lower domain spacing and increased polymer mobility, while larger inverse tapers correspond to even lower domain spacing but decreased mobility. Thus the changes in dynamics with tapering cannot be explained by mapping to a diblock system at an adjusted effective segregation strength. This material is based upon work

  5. Contribution of orientational effects into radiation-chemical properties of segregated block copolymers

    International Nuclear Information System (INIS)

    Model of radiolysis of microphase-separated block copolymers of PS with PB is proposed. According this scheme the radiation-chemical yields of paramagnetic centres and crosslinks in PB domains differ from those for the PB homopolymer by the value proportional to the fraction of ordered chain segments. This orientational small-scale order arises as a result of the deformation of chains in a domain in the direction perpendicular to the interphase

  6. Chain elongation suppression of cyclic block copolymers in lamellar microphase-separated bulk

    OpenAIRE

    Matsushita, Y; Iwata, H; Asari, T; Uchida, T.; ten Brinke, G.; Takano, A

    2004-01-01

    Chain elongation suppression of cyclic block copolymers in microphase-separated bulk was determined quantitatively. Solvent-cast and annealed films are confirmed to show alternating lamellar structure and their microdomain spacing D increases with increasing total molecular weight M according to the relationship Dproportional toM(0.59), which agrees quite consistently with the theoretically predicted power law, i.e., Dproportional toM(3/5). This result is in contrast to the well-established i...

  7. CdS-containing nano-assemblies of double hydrophilic block copolymers in water

    Czech Academy of Sciences Publication Activity Database

    Uchman, M.; Procházka, K.; Gatsouli, K.; Pispas, S.; Špírková, Milena

    2011-01-01

    Roč. 289, č. 9 (2011), s. 1045-1053. ISSN 0303-402X R&D Projects: GA ČR GCP205/11/J043; GA ČR GAP208/10/0353 Institutional research plan: CEZ:AV0Z40500505 Keywords : double hydrophilic block copolymers * polymer self-assembly * light scattering Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.331, year: 2011

  8. Single-molecule protein arrays enabled by scanning probe block copolymer lithography

    OpenAIRE

    Chai, Jinan; Wong, Lu Shin; Giam, Louise; Mirkin, Chad A.

    2011-01-01

    The ability to control the placement of individual protein molecules on surfaces could enable advances in a wide range of areas, from the development of nanoscale biomolecular devices to fundamental studies in cell biology. Such control, however, remains a challenge in nanobiotechnology due to the limitations of current lithographic techniques. Herein we report an approach that combines scanning probe block copolymer lithography with site-selective immobilization strategies to create arrays o...

  9. Selective gas transfer through binary polymeric systems based on block-copolymers.

    Science.gov (United States)

    Beckman, I N; Teplyakov, V V

    2015-08-01

    Evaluation of several versions of phenomenological theory of gas permeability in selective polymeric membranes is presented, along with the appropriate experimental methods for verification of these versions. The main focus is on a description of stationary mass transfer across membranes (films) containing dispersion inclusions of various shapes of one polymer in a matrix of another. Considering heterogeneous media as a membrane material, it was assumed that diffusion and sorption properties of inclusions are different from those of the dispersing medium. The problem of choosing optimal shape of inclusions is evaluated from the point of view of targeted permeability and selectivity of a membrane with respect to gases. To confirm this theoretical approach, the experimental results of the studies of diffusion (permeability) of permanent gases in polymeric membranes of different structures were used. The target gases included noble gases, hydrogen, nitrogen, oxygen, CO2, and methane. The target polymers included glassy polyvinyltrimethylsilane (PVTMS, T(gl)=155-180 °C), rubberlike polydimethylsiloxane (PDMS, T(gl)=-120 °C), and two-phase block-copolymers based on these materials within a wide range of composition, including the region of phase inversion. In addition, available experimental literature data on gas permeation parameters for polyarylat-polysiloxane, polysulfon-polysiloxane, and polycarbonate-polysiloxane block-copolymers are utilized. In order to describe the stationary gas permeability for two-phase systems (from diluted dispersion of one polymer in another to concentrated dispersion and complete phase inversion) the empiric approaches based on modified Maxwell equations are offered. The requirements for two-phase systems with high permeability and selectivity parameters for gas separation are identified. The permeability parameters are predicted for C1-C4 hydrocarbons in block-copolymers based on PDMS dispersion in PVTMS, phase inversion, and PVTMS

  10. Holographic Gratings and Data Storage in Azobenzene-Containing Block Copolymers and Molecular Glasses

    Science.gov (United States)

    Audorff, Hubert; Kreger, Klaus; Walker, Roland; Haarer, Dietrich; Kador, Lothar; Schmidt, Hans-Werner

    This review covers synthesis, materials development, and photophysics of azobenzene-containing block copolymers as potential media for reversible volume holographic data storage. For high-density holographic data storage, volume gratings must be inscribed in millimeter-thick samples to achieve efficient angle multiplexing. It is demonstrated that block copolymers with azobenzene side-groups in the minority block develop no detrimental surface relief structures and exhibit superior performance regarding volume gratings, compared to homopolymers and statistical copolymers. Several material concepts for optimizing the refractive index modulation and the stability of volume gratings are presented. Stabilities of more than 2 years were achieved. Most important is the development of polymer blends comprising the azobenzene-containing block copolymer and an optically transparent homopolymer. This enables the preparation of millimeter-thick samples with the required optical density of ˜ 0. 7 at the writing wavelength by conventional injection molding techniques. The inscription of up to 200 holograms at the same lateral position was demonstrated. In addition, more than 1,000 write/erase cycles can be performed. This is the first time that the inscription and erasure of the long-term stable angle-multiplexed volume gratings in a rewritable polymeric medium have been achieved by purely optical means. A second important application for azobenzene-containing materials is the controlled preparation of surface relief structures. It is demonstrated that azobenzene-containing molecular glasses are an ideal class for efficient formation of surface relief gratings (SRGs) with amplitude heights of more than 600 nm. Clear relationships can be established between the chemical structure of the molecules and the behavior of SRG formation. All results are in agreement with the gradient force model by Kumar et al. The surface patterns are stable enough to be transferred to a polymer

  11. Use of Superparamagnetic Nanoparticle/Block Copolymer Electrostatic Complexes as Contrast Agents in Magnetic Resonance Imaging

    OpenAIRE

    Berret, Jean-Francois; Cartier, Regis

    2007-01-01

    During the past years we have investigated the complexation between nanocolloids and oppositely charged polymers. The nanocolloids examined were ionic surfactant micelles and inorganic oxide nanoparticles. For the polymers, we used homopolyelectrolytes and block copolymers with linear and comb architectures. In general, the attractive interactions between oppositely charged species are strong and as such, the simple mixing of solutions containing dispersed constituents yield to a precipitatio...

  12. Ultra-cold neutron interaction with the copolymer block of polystyrene-polybutadiene-polystyrene type

    International Nuclear Information System (INIS)

    An ultra-cold neutron (UCN) spectrometer has been used to study dependences of the total interaction cross sections on the UCN wave length (Σsub(t)(lambda)) with copolymer block of polystyrene-polybutadiene-polystyrene type at room temperature and 99 K. Investigation into dependences of the UCN total interaction cross sections is a considerably informative method in studying the structure and dynamics of substances, possessing an ordered epimolecular structure

  13. NMR study of thermoresponsive micelles of amphiphilic block copolymers in aqueous solution

    Czech Academy of Sciences Publication Activity Database

    Spěváček, Jiří; Konefal, Rafal; Čadová, Eva

    Zurich: Swiss Federal Institute of Technology, 2014. s. 387. ISBN 978-3-906031-54-5. [Euromar 2014. Magnetic Resonance Conference. 29.06.2014-03.07.2014, Zürich] R&D Projects: GA ČR(CZ) GA13-23392S Institutional support: RVO:61389013 Keywords : thermoresponsive block copolymer * poly(N-isopropylacrylamide) * poly(ethylene glycol) Subject RIV: CD - Macromolecular Chemistry

  14. Block copolymer self-assembly and co-assembly : shape function and application

    OpenAIRE

    Li, F

    2009-01-01

    Amphiphilic block copolymers can, in selective solvents such as water, assemble into various shapes and architectures. Among those, polymer vesicles, polymer micelles and polymer fibers are very popular structures in current nanotechnology. These objects each have their own particular properties and can serve as containers or templates for different nanotechnological applications. Polymer vesicles, for example, can encapsulate both hydrophobic and hydrophilic molecules, and are therefore cons...

  15. Electrochemical and bioelectrocatalytical properties of novel block-copolymers containing interacting ferrocenyl units

    OpenAIRE

    Garcia Armada, Maria del Pilar; Losada del Barrio, Jose; Lopez Villanueva, F.J.; H. Frey; Alonso Garrido, Beatriz; Casado Santana, Carmen M.

    2008-01-01

    The electrochemical characterization of three different polystyrene-b-polybutadiene block copolymers functionalized with ferrocenyl units electronically communicated, PSm-PBn(HSiMeFc2)p where m=615, n=53, p=39 (1), m=375, n=92, p=76 (2) and m=455, n=204, p=170 (3), has been carried out both in solution and electrochemically deposited onto platinum electrodes. The bioelectrocatalytical properties of electrodes modified with the polymers in the nicotinamide dinucleotide (NADH) and glucose oxida...

  16. Novel architecture design of block copolymers of ethylene glycol methyl ether methacrylate and carboxybetaine acrylamide

    Czech Academy of Sciences Publication Activity Database

    Rodriguez-Emmenegger, Cesar; Hasan, E.; Brynda, Eduard; Houska, Milan; Sedláková, Zdeňka; Bologna Alles, A.; Huck, W.

    Praha : Institute of Macromolecular Chemistry, 2009. s. 111. ISBN 978-80-85009-59-0. [Prague Meetings on Macromolecules /73./ New Frontiers in Macromolecular Science: From Macromolecular Concepts of Living Matter to Polymers for Better Quality of Life. 05.07.2009-09.07.2009, Prague] R&D Projects: GA AV ČR KAN200670701 Institutional research plan: CEZ:AV0Z40500505 Keywords : block copolymers Subject RIV: CD - Macromolecular Chemistry

  17. Photoresponsive Azopolyester–PMMA Block Copolymers Obtained by Combination of ATRP, Polycondensation, and “Click” Chemistry

    DEFF Research Database (Denmark)

    Berges, Cristina; Javakhishvili, Irakli; Hvilsted, Søren; Sánchez, Carlos; Alcalá, Rafael

    2012-01-01

    Novel azobenzene‐containing block copolymers (BCs) with a polyester block bearing azobenzene moieties in the side chain and a poly (methyl methacrylate) (PMMA) block have been synthesized by the combination of atom transfer radical polymerization (ATRP), polycondensation, and “click” chemistry. Two...

  18. Selective directed self-assembly of coexisting morphologies using block copolymer blends

    Science.gov (United States)

    Stein, A.; Wright, G.; Yager, K. G.; Doerk, G. S.; Black, C. T.

    2016-01-01

    Directed self-assembly (DSA) of block copolymers is an emergent technique for nano-lithography, but is limited in the range of structures possible in a single fabrication step. Here we expand on traditional DSA chemical patterning. A blend of lamellar- and cylinder-forming block copolymers assembles on specially designed surface chemical line gratings, leading to the simultaneous formation of coexisting ordered morphologies in separate areas of the substrate. The competing energetics of polymer chain distortions and chemical mismatch with the substrate grating bias the system towards either line/space or dot array patterns, depending on the pitch and linewidth of the prepattern. This is in contrast to the typical DSA, wherein assembly of a single-component block copolymer on chemical templates generates patterns of either lines/spaces (lamellar) or hexagonal dot arrays (cylinders). In our approach, the chemical template encodes desired local spatial arrangements of coexisting design motifs, self-assembled from a single, sophisticated resist. PMID:27480327

  19. Amphiphilic Spider Silk-Like Block Copolymers with Tunable Physical Properties and Morphology for Biomedical Applications

    Science.gov (United States)

    Huang, Wenwen; Krishnaji, Sreevidhya; Kaplan, David; Cebe, Peggy

    2013-03-01

    Silk-based materials are important candidates for biomedical applications because of their excellent biocompatibility and biodegradability. To generate silk amphiphilic biopolymers with potential use in guided tissue repair and drug delivery, a novel family of spider silk-like block copolymers was synthesized by recombinant DNA technology. Block copolymer thermal properties, structural conformations, protein-water interactions, and self-assembly morphologies were studied with respect to well controlled protein amino acid sequences. A theoretical model was used to predict the heat capacity of the protein and protein-water complex. Using thermal analysis, two glass transitions were observed: Tg1 is related to conformational changes caused by bound water removal, while Tg2 (>Tg1) is the glass transition of dry protein. Real-time infrared spectroscopy and X-ray diffraction confirmed that different secondary structural changes occur during the two Tg relaxations. Using scanning electron microscopy, fibrillar networks and hollow vesicles are observed, depending on protein block copolymer sequence. This study provides a deeper understanding of the relationship between protein physical properties and amino acid sequence, with implications for design of other protein-based materials. Support was provided from the NSF CBET-0828028 and the MRI Program under DMR-0520655 for thermal analysis instrumentation.

  20. Electrostatic self-assembly in polyelectrolyte-neutral block copolymers and oppositely charged surfactant solutions

    International Nuclear Information System (INIS)

    We report on small-angle neutron scattering (SANS) of colloidal complexes resulting from the electrostatic self-assembly of polyelectrolyte-neutral copolymers and oppositely charged surfactants. The polymers are double hydrophilic block copolymers of low molecular weight (between 5000 and 50 000 g/mol). One block is a polyelectrolyte chain, which can be either positively or negatively charged, whereas the second block is neutral and in good solvent conditions. In aqueous solutions, surfactants with an opposite charge to that of the polyelectrolyte interact strongly with these copolymers. The two species associate into stable 100 nm-colloidal complexes which exhibit a core-shell microstructure. For different polymer/surfactant couples, we have shown that the core is constituted from densely packed surfactant micelles connected by the polyelectrolyte chains. The outer part of the complex is a corona formed by the neutral soluble chains. Using a model of aggregation based on a Monte-Carlo algorithm, we have simulated the internal structure of the aggregates. The model assumes spherical cages containing one to several hundreds of micelles in a closely packed state. The agreement between the model and the data is remarkable

  1. Gel formation in a mixture of a block copolymer and a nematic liquid crystal.

    Science.gov (United States)

    Khazimullin, Maxim; Müller, Thomas; Messlinger, Stephan; Rehberg, Ingo; Schöpf, Wolfgang; Krekhov, Alexei; Pettau, Robin; Kreger, Klaus; Schmidt, Hans-Werner

    2011-08-01

    The viscoelastic properties of a binary mixture of a mesogenic side-chain block copolymer in a low molecular weight nematic liquid crystal are studied for mass concentrations ranging from the diluted regime up to a liquid crystalline gel state at about 3%. In the gel state, the system does not flow, exhibits a polydomain structure on a microscopic level, and strongly scatters light. Below the gelation point, the system is homogeneous and behaves like a usual nematic, so the continuum theory of liquid crystals can be applied for interpreting the experimental data. Using the dynamic Fréedericksz transition technique, the dependence of the splay elastic constant and the rotational viscosity on the polymer concentration have been obtained. Comparing the dynamic behavior of block copolymer solutions with the respective homopolymer solutions reveals that, above a mass concentration of 1%, self-assembling of the block copolymer chain segments in clusters occurred, resulting in a gel state at higher concentrations. The effective cluster size is estimated as a function of the concentration, and a scaling-law behavior near the sol-gel transition is confirmed. This technique may serve as an alternative method for determining the gelation point. PMID:21929007

  2. Gel formation in a mixture of a block copolymer and a nematic liquid crystal

    Science.gov (United States)

    Khazimullin, Maxim; Müller, Thomas; Messlinger, Stephan; Rehberg, Ingo; Schöpf, Wolfgang; Krekhov, Alexei; Pettau, Robin; Kreger, Klaus; Schmidt, Hans-Werner

    2011-08-01

    The viscoelastic properties of a binary mixture of a mesogenic side-chain block copolymer in a low molecular weight nematic liquid crystal are studied for mass concentrations ranging from the diluted regime up to a liquid crystalline gel state at about 3%. In the gel state, the system does not flow, exhibits a polydomain structure on a microscopic level, and strongly scatters light. Below the gelation point, the system is homogeneous and behaves like a usual nematic, so the continuum theory of liquid crystals can be applied for interpreting the experimental data. Using the dynamic Fréedericksz transition technique, the dependence of the splay elastic constant and the rotational viscosity on the polymer concentration have been obtained. Comparing the dynamic behavior of block copolymer solutions with the respective homopolymer solutions reveals that, above a mass concentration of 1%, self-assembling of the block copolymer chain segments in clusters occurred, resulting in a gel state at higher concentrations. The effective cluster size is estimated as a function of the concentration, and a scaling-law behavior near the sol-gel transition is confirmed. This technique may serve as an alternative method for determining the gelation point.

  3. Synthesis, micellar properties and application of amphiphilic linear block copolymers with different microstructure but same molecular weight

    OpenAIRE

    Schmitz, Christof Jan Wilhelm

    2009-01-01

    This dissertation is concerned with the synthesis and micellisation behaviour of linear block copolymers based on methacrylates by means of the modern controlled radical polymerisation technique, namely the atom transfer radical polymerisation (ATRP). The objective was the synthesis of linear block copolymers with different microstructure but same molecular weight. The chosen synthesis strategy should be applicable for various monomer pairs with different polarities and should include the use...

  4. Nanoporous materials from stable and metastable structures of 1,2-PB-b-PDMS block copolymers

    DEFF Research Database (Denmark)

    Schulte, Lars; Grydgaard, Anne; Jakobsen, Mathilde R.;

    2011-01-01

    Experimental procedures used at the preparation and characterization stages of nanoporous materials (NPM) from 1,2-polybutadiene-b-polydimethylsiloxane (1,2-PB-b-PDMS) block copolymers are presented. The NPM were obtained from self-assembled block copolymers after firstly cross-linking 1,2-PB (the...... characterization of the materials at different stages of preparation includes gravimetry, infrared spectroscopy, small angle x-ray scattering, electron microscopy and isothermal nitrogen adsorption experiments....

  5. Neutron Reflection Studies on Lamellar Microphase-Separated Structures of Two-Component Block Copolymers with Composition Distribution

    International Nuclear Information System (INIS)

    Segmental distribution of polystyrene blocks in lamellar microphase-separated poly(styrene-block-2-vinylpyridine) (SP) with wide composition distribution was investigated by neutron reflectivity measurements using deuterium-labeled polymers. Block copolymers with wide composition distribution were produced by mixing three monodispersed parent block copolymers, which were synthesized by an anionic polymerization method to have the same total molecular weight but with different volume fractions. The block copolymer blends whose overall S/P ratio is 0.5/0.5 were found to form a uniform lamellar structure, where lamellae were highly oriented along the direction parallel to the film surface and the interfacial thickness was evaluated as 40 A. It was clarified that a shorter block chain in the microdomain is localized at the domain boundary, while a longer one has a peak at the center of microdomain in its segmental distribution profile

  6. Ultrasound responsive block copolymer micelle of poly(ethylene glycol)-poly(propylene glycol) obtained through click reaction.

    Science.gov (United States)

    Li, Fayong; Xie, Chuan; Cheng, Zhengang; Xia, Hesheng

    2016-05-01

    The well-defined amphiphilic poly(ethylene glycol)-block-poly(propylene glycol) copolymer containing 1, 2, 3-triazole moiety and multiple ester bonds (PEG-click-PPG) was prepared by click reaction strategy. The PEG-click-PPG copolymer can self-assemble into spherical micelles in aqueous solution. It is found that high intensity focused ultrasound (HIFU) can open the copolymer PEG-click-PPG micelles and trigger the release of the payload in the micelle. The multiple ester bonds introduced in the junction point of the copolymer chain through click reactions were cleaved under HIFU, and leads to the disruption of the copolymer micelle and fast release of loaded cargo. The click reaction provides a convenient way to construct ultrasound responsive copolymer micelles with weak bonds. PMID:26703197

  7. Cooperative catalysis with block copolymer micelles: A combinatorial approach

    KAUST Repository

    Bukhryakov, Konstantin V.

    2015-02-09

    A rapid approach to identifying complementary catalytic groups using combinations of functional polymers is presented. Amphiphilic polymers with "clickable" hydrophobic blocks were used to create a library of functional polymers, each bearing a single functionality. The polymers were combined in water, yielding mixed micelles. As the functional groups were colocalized in the hydrophobic microphase, they could act cooperatively, giving rise to new modes of catalysis. The multipolymer "clumps" were screened for catalytic activity, both in the presence and absence of metal ions. A number of catalyst candidates were identified across a wide range of model reaction types. One of the catalytic systems discovered was used to perform a number of preparative-scale syntheses. Our approach provides easy access to a range of enzyme-inspired cooperative catalysts.

  8. Block Copolymer-Based Supramolecular Elastomers with High Extensibility and Large Stress Generation Capability

    Science.gov (United States)

    Noro, Atsushi; Hayashi, Mikihiro

    We prepared block copolymer-based supramolecular elastomers with high extensibility and large stress generation capability. Reversible addition fragmentation chain transfer polymerizations were conducted under normal pressure and high pressure to synthesize several large molecular weight polystyrene-b-[poly(butyl acrylate)-co-polyacrylamide]-b-polystyrene (S-Ba-S) block copolymers. Tensile tests revealed that the largest S-Ba-S with middle block molecular weight of 3140k achieved a breaking elongation of over 2000% with a maximum tensile stress of 3.6 MPa and a toughness of 28 MJ/m3 while the reference sample without any middle block hydrogen bonds, polystyrene-b-poly(butyl acrylate)-b-polystyrene with almost the same molecular weight, was merely viscous and not self-standing. Hence, incorporation of hydrogen bonds into a long soft middle block was found to be beneficial to attain high extensibility and large stress generation capability probably due to concerted combination of entropic changes and internal potential energy changes originaing from the dissociation of multiple hydrogen bonds by elongation. This work was supported by JSPS KAKENHI Grant Numbers 13J02357, 24685035, 15K13785, and 23655213 for M.H. and A.N. A.N. also expresses his gratitude for Tanaka Rubber Science & Technology Award by Enokagaku-Shinko Foundation, Japan.

  9. Electron Propagation within Redox-Active Microdomains in Thin Films of Ferrocene-Containing Diblock Copolymers.

    Science.gov (United States)

    Ghimire, Govinda; Yi, Yi; Derylo, Maksymilian A; Baker, Lane A; Ito, Takashi

    2015-11-10

    This paper reports the electrochemical behavior of redox-active microdomains in thin films of ferrocene-containing diblock copolymers, polystyrene-block-poly(2-(acryloyloxy)ethyl ferrocenecarboxylate) (PS-b-PAEFc). PS-b-PAEFc with different PAEFc volume fractions (PS154-b-PAEFc51, PS154-b-PAEFc26, and PS154-b-PAEFc12, where the subscripts represent the polymerization degree of each block; f(PAEFc) = 0.47, 0.30, and 0.17, respectively) was synthesized by sequential atom transfer radical polymerization. PS-b-PAEFc films of controlled thicknesses (20-160 nm) were prepared on gold substrates via spin-coating and characterized by ellipsometry. Microdomains were observed via atomic force microscopy on the surfaces of PS154-b-PAEFc51 and PS154-b-PAEFc26 thin films but not on the surfaces of PS154-b-PAEFc12 thin films. Electrochemical behavior of films was assessed by cyclic voltammetry and chronocoulometry in acetonitrile solution. The redox potential of ferrocene moieties was similar (ca. + 0.29 V vs Fc(+)/Fc) regardless of fPAEFc and film thickness. For PS154-b-PAEFc51 and PS154-b-PAEFc26, thicker films afforded larger faradaic peak currents and exhibited diffusion-controlled voltammograms at faster sweep rates. PS154-b-PAEFc26 produced voltammograms less influenced by solvent-induced swelling than PS154-b-PAEFc51, reflecting the improved morphological stability of PAEFc microdomains by redox-inert PS frameworks. In contrast, PS154-b-PAEFc12 films yielded similar faradaic peak currents regardless of film thickness and exhibited voltammograms indicative of surface-confined species. These observations suggest that PS154-b-PAEFc51 and PS154-b-PAEFc26 films contain continuous PAEFc microdomains extending from the electrode to the surface, in contrast to the PS154-b-PAEFc12 films which contain isolated PAEFc microdomains buried within the PS matrix. Electron propagation took place only through PAEFc microdomains that could electrically communicate with the underlying

  10. Dielectric relaxation of thin films of polyamide random copolymers

    Science.gov (United States)

    Taniguchi, Natsumi; Fukao, Koji; Sotta, Paul; Long, Didier R.

    2015-05-01

    We investigate the relaxation behavior of thin films of a polyamide random copolymer, PA66/6I, with various film thicknesses using dielectric relaxation spectroscopy. Two dielectric signals are observed at high temperatures, the α process and the relaxation process due to electrode polarization (the EP process). The relaxation time of the EP process has a Vogel-Fulcher-Tammann type of temperature dependence, and the glass transition temperature, Tg, evaluated from the EP process agrees very well with the Tg determined from the thermal measurements. The fragility index derived from the EP process increases with decreasing film thickness. The relaxation time and the dielectric relaxation strength of the EP process are described by a linear function of the film thickness d for large values of d , which can be regarded as experimental evidence for the validity of attributing the observed signal to the EP process. Furthermore, there is distinct deviation from this linear law for thicknesses smaller than a critical value. This deviation observed in thinner films is associated with an increase in the mobility and/or diffusion constant of the charge carriers responsible for the EP process. The α process is located in a higher-frequency region than the EP process at high temperatures but merges with the EP process at lower temperatures near the glass transition region. The thickness dependence of the relaxation time of the α process is different from that of the EP process. This suggests that there is decoupling between the segmental motion of the polymers and the translational motion of the charge carriers in confinement.

  11. Molecular Dynamics Modelling of Block-Copolymer Electrolytes with High t+ Values

    International Nuclear Information System (INIS)

    Molecular Dynamics simulations of the BAB type triblock copolymer lithium poly[(4-styrenesulfonyl) (trifluoromethylenesulfonyl) imide)]-block-poly(ethylene oxide)-block-lithium poly[(4-stryrenesylfonyl) (trifluoromethanesulfonyl) imide] (P(STFSILi)-b-PEO-b-P(STFSILi)) were carried out for different simulation temperatures and B-block lengths. By covalently binding the anion to the polymer backbone, it is immobilised and the cation transference number thereby raised significantly. It was found that the Li-ion diffusion decreases exponentially with growth of the B-block length. The poly(ethylene oxide) matrix dissolves Li-ions already during the equilibration stage of the simulation, and no Li-ion diffusion pathways were identified along the STFSI branches, which significantly influence the transport properties of the material

  12. Dip-pen nanolithography on (bio)reactive monolayer and block-copolymer platforms: deposition of lines of single macromolecules.

    Science.gov (United States)

    Salazar, Ramon B; Shovsky, Alexander; Schönherr, Holger; Vancso, G Julius

    2006-11-01

    The application of atomic force microscopy (AFM) tip-mediated molecular transfer (dip-pen nanolithography or DPN) to fabricate nanopatterned (bio)reactive platforms based on dendrimers on reactive self-assembled monolayer (SAM) and polymer thin films is discussed. The transfer of high-molar-mass polyamidoamine (PAMAM) dendrimers (generation 5) and the rapid in situ covalent attachment of the deposited adsorbates onto reactive N-hydroxysuccinimide (NHS) terminated SAMs on gold and NHS-activated polystyrene-block-poly(tert-butyl acrylate) (PS(690)-b-PtBA(1210)) block copolymer thin films were investigated as strategies to suppress line broadening by surface diffusion in DPN. By exploiting carefully controlled environmental conditions (such as temperature and relative humidity), scan rates, and in particular the covalent attachment of the dendrimers to the reactive films, the observed line broadening and hence the lateral diffusion of dendrimers was substantially less pronounced compared to that observed with DPN of thiols on gold. By this method, high-definition patterns of dendrimers were conveniently fabricated down to 30-nm length scales. The presence of primary amino groups in the deposited dendrimers ultimately offers the possibility to anchor biochemically relevant molecules, such as proteins and polypeptides, to these nanostructured platforms for a wide range of possible applications in the life sciences and in particular for the investigation of controlled cell-surface interactions. PMID:17192974

  13. Meso-scale Modeling of Block Copolymers Self-Assembly in Casting Solutions for Membrane Manufacture

    KAUST Repository

    Moreno Chaparro, Nicolas

    2016-05-01

    Isoporous membranes manufactured from diblock copolymer are successfully produced at laboratory scale under controlled conditions. Because of the complex phenomena involved, membrane preparation requires trial and error methodologies to find the optimal conditions, leading to a considerable demand of resources. Experimental insights demonstrate that the self-assembly of the block copolymers in solution has an effect on the final membrane structure. Nevertheless, the complete understanding of these multi-scale phenomena is elusive. Herein we use the coarse-grained method Dissipative Particle Dynamics to study the self-assembly of block copolymers that are used for the preparation of the membranes. To simulate representative time and length scales, we introduce a framework for model reduction of polymer chain representations for dissipative particle dynamics, which preserves the properties governing the phase equilibria. We reduce the number of degrees of freedom by accounting for the correlation between beads in fine-grained models via power laws and the consistent scaling of the simulation parameters. The coarse-graining models are consistent with the experimental evidence, showing a morphological transition of the aggregates as the polymer concentration and solvent affinity change. We show that hexagonal packing of the micelles can occur in solution within different windows of polymer concentration depending on the solvent affinity. However, the shape and size dispersion of the micelles determine the characteristic arrangement. We describe the order of crew-cut micelles using a rigid-sphere approximation and propose different phase parameters that characterize the emergence of monodisperse-spherical micelles in solution. Additionally, we investigate the effect of blending asymmetric diblock copolymers (AB/AC) over the properties of the membranes. We observe that the co-assembly mechanism localizes the AC molecules at the interface of A and B domains, and induces

  14. Highly protein-resistant coatings and suspension cell culture thereon from amphiphilic block copolymers prepared by RAFT polymerization.

    Science.gov (United States)

    Haraguchi, Kazutoshi; Kubota, Kazuomi; Takada, Tetsuo; Mahara, Saori

    2014-06-01

    Novel amphiphilic block copolymers composed of hydrophobic (poly(2-methoxyethyl acrylate): M) and hydrophilic (poly(N,N-dimethylacrylamide): D) segments were synthesized by living radical polymerization: a reversible addition-fragmentation chain-transfer polymerization. Two types of amphiphilic block copolymers, triblock (MDM) and 4-arm block ((MD)4) copolymers with specific compositions (D/M = (750-1500)/250), were prepared by a versatile one-pot synthesis. These copolymers show good adhesion to various types of substrates (e.g., polystyrene, polycarbonate, polypropylene, Ti, and glass), and the surface coating showed high protein repellency and a low contact angle for water, regardless of the substrate. The two opposing characteristics of high protein repellency and good substrate adhesion were achieved by the combined effects of the molecular architecture of the block copolymers, the high molecular weight, and the characteristics of each segment, that is, low protein adsorption capability of both segments and low glass transition temperature of the hydrophobic segment. Further, a polystyrene dish coated with the MDM block copolymer could be sterilized by γ-ray irradiation and used as a good substrate for a suspension cell culture that exhibits low cell adhesion and good cell growth. PMID:24773089

  15. Nanostructured Double Hydrophobic Poly(Styrene-b-Methyl Methacrylate) Block Copolymer Membrane Manufactured Via Phase Inversion Technique

    KAUST Repository

    Karunakaran, Madhavan

    2016-03-11

    In this paper, we demonstrate the formation of nanostructured double hydrophobic poly(styrene-b-methyl methacrylate) (PS-b-PMMA) block copolymer membranes via state-of-the-art phase inversion technique. The nanostructured membrane morphologies are tuned by different solvent and block copolymer compositions. The membrane morphology has been investigated using FESEM, AFM and TEM. Morphological investigation shows the formation of both cylindrical and lamellar structures on the top surface of the block copolymer membranes. The PS-b-PMMA having an equal block length (PS160K-b-PMMA160K) exhibits both cylindrical and lamellar structures on the top layer of the asymmetric membrane. All membranes fabricated from PS160K-b-PMMA160K shows an incomplete pore formation in both cylindrical and lamellar morphologies during the phase inversion process. However, PS-b-PMMA (PS135K-b-PMMA19.5K) block copolymer having a short PMMA block allowed us to produce open pore structures with ordered hexagonal cylindrical pores during the phase inversion process. The resulting PS-b-PMMA nanostructured block copolymer membranes have pure water flux from 105-820 l/m2.h.bar and 95% retention of PEG50K

  16. Hierarchical assembly of block copolymer micelles into reversible networks: MC simulations

    Science.gov (United States)

    Wang, Zilu; Dormidontova, Elena

    2015-03-01

    The rapid development of nanoscience has considerably expanded the range of building blocks for complex self-assembled nanostructure formation, which show great potential for numerous advanced applications. We apply Monte Carlo simulations to gain understanding of molecular mechanism of self-assembly of nanostructures formed by diblock copolymer micelles interconnected by means of metal-ligand complexation. These systems exhibit interesting chemical and mechanical stimuli-responsive behavior and possess two levels of self-assembly: 1) self-assembly of diblock copolymers into micelles and 2) reversible inter-micelle bridging by coordination bonding between metal ions and ligands attached to the corona of nanoparticles, which is responsible for the network viscoelastic properties. Using MC simulations we investigate the effect of metal-ligand complexation on diblock-copolymer micelle formation and vice versa. We analyze the extent of intra- and inter-micelle loops and bridges formed by metal-ligand complexation in relation to the degree of crosslinking and elastic properties of the network. The effect of polymer concentration, hydrophilic block length, metal to oligomer ratio and type of complexation (2:1 or 3:1) on equilibrium properties of reversible networks will be discussed.

  17. Influencing the structure of block copolymer micelles with small molecule additives

    Science.gov (United States)

    Robertson, Megan; Singh, Avantika; Cooksey, Tyler; Kidd, Bryce; Piemonte, Rachele; Wang, Shu; Mai Le, Kim; Madsen, Louis

    Amphiphilic block copolymer micelles in water are under broad exploration for drug delivery applications due to their high loading capacity and targeted drug delivery. We aim to understand the kinetic and thermodynamic processes that underlie the self-assembly of diblock copolymer micelle systems. The present work focuses on diblock copolymers containing poly(ethylene oxide) (a hydrophilic polymer) and polycaprolactone (a hydrophobic polymer), which spontaneously self-assemble into spherical micelles in water. Addition of a common good solvent (a co-solvent) for both of the constituting blocks, such as tetrahydrofuran (THF), reduces the interfacial tension at the core-corona interface. We are currently investigating the effect of this phenomenon on the micelle structural properties, using small-angle scattering and nuclear magnetic resonance. We have characterized the hydrodynamic radius, core radius, corona thickness, aggregation number, degree of swelling of the micelle core with the co-solvent, and unimer (free chain) concentration, as a function of the co-solvent concentration. Fundamental knowledge from these studies will inform design of drug delivery systems by allowing us to tailor micelle properties for optimal cargo loading.

  18. Small angle neutron scattering study of doxorubicin–surfactant complexes encapsulated in block copolymer micelles

    Indian Academy of Sciences (India)

    Jayita Bhattacharjee; Gunjan Verma; V K Aswal; P A Hassan

    2008-11-01

    Self-assembling behaviour of block copolymers and their ability to evade the immune system through polyethylene oxide stealth makes it an attractive candidate for drug encapsulation. Micelles formed by polyethylene oxide–polypropylene oxide–polyethylene oxide triblock copolymers (PEO–PPO–PEO), pluronic P123, have been employed for encapsulating the anti-cancer drug doxorubicin hydrochloride. The binding affinity of doxorubicin within the micelle carrier is enhanced through complex formation of drug and anionic surfactant, aerosol OT (AOT). Electrostatic binding of doxorubicin with negatively charged surfactants leads to the formation of hydrophobic drug–surfactant complexes. Surfactant-induced partitioning of the anti-cancer drug into nonpolar solvents such as chloroform is investigated. SANS measurements were performed on pluronic P123 mi-celles in the presence of drug–surfactant complex. No significant changes in the structure of the micelles are observed upon drug encapsulation. This demonstrates that surfactant–drug complexes can be encapsulated in block copolymer micelles without disrupting the structure of aggregates.

  19. John H. Dillon Medal: Tapered Block Copolymers: Tuning Self-Assembly and Properties by Manipulating Monomer Segment Distributions

    Science.gov (United States)

    Epps, Thomas

    The self-assembly of block copolymers (BCPs) presents unique opportunities to design materials with attractive chemical and mechanical properties based on the ability of BCPs to form periodic structures with nanoscale domain spacings. One area of recent progress in our group focuses on the behavior of tapered BCPs in which the segment distribution at the interface between blocks is synthetically varied to tune morphology, domain density profiles, thermal transitions as well as mechanical and transport properties. Two application targets for these materials are lithium-ion conducting membranes for batteries and nanostructured thin films for nanotemplates and barrier membranes. In the first target area, we found that the taper volume fraction and composition allow us to manipulate the self-assembly of salt-doped BCPs in a well-defined manner that permits optimization of morphology and ion-content. Additionally, we found that the tapered interfaces influence the glass-transition behavior of the ion-conducting block leading to significant changes in lithium-ion transport (ion conductivity). In the second target area, we found the taper content alters the rate of self-assembly as well as the rate of island/hole formation (and ultimate island/hole size) upon thermal annealing. Additionally, using reflectivity techniques, we probed the domain density profiles as a function of taper composition and linked these profiles to changes in domain spacing and glass transition temperature. Overall, these studies show the versatility of tapering to provide a unique handle for simultaneously optimizing multiple materials properties.

  20. Nanopatterning by large block copolymers for application in photonic devices (Conference Presentation)

    Science.gov (United States)

    Mokarian-Tabari, Parvaneh; Senthamaraikannan, Ramsankar; Collins, Timothy W.; Glynn, Colm; O'Dwyer, Colm; Morris, Michael

    2016-04-01

    The extensive benefits of the new generation of nanostructured surfaces is very promising for enhancing light absorption efficiency in photonic devices. However, the low throughput and the high cost of available technologies such as lithography for fabrication of nanostructures has proved to be a difficult technological hurdle for advanced manufacturing. In this research we present a solution based process based on high molecular weight block copolymer (BCP) nanolithography for fabrication of periodic structures on large areas of optical surfaces. Block copolymer self- assembly technique is a solution based process that offers an alternative route to produce highly ordered photonic crystal structures. BCPs forms nanodomains (5-10 nm) due to microphase separation of incompatible constitute blocks. The size and shape of the nanostructure can be customised by the molecular weight and volume fraction of the polymer blocks. However, the major challenge is BCPs do not phase separate into their signature ordered pattern above 100 nm, whereas for nanofeatures to be used as photonic gratings, they must be greater than 100 nm (typically ¼ wavelength). This is due to significant kinetic penalty arising from higher entanglement in high molecular weight polymers. In this work we present the results of exploiting commercially available block copolymers to phase separate into periodic domains greater than 100 nm. The process do not include any blending with homopolymers, or adding colloidal particles, and to our best knowledge, has not been yet achieved or reported in the literatures. We have pattern transferred the BCP mask to silicon substrate by reactive ion etch (ICP-RIE). The final product is black silicon, consists of hexagonally packed conic Si nanofeatures with diameter above 100nm and periodicity of 200 nm. The height of the Si nanopillars varies from 100 nm to 1 micron. We have characterized the angle dependent optical reflectance properties of the black silicon. The

  1. Anti-Biofouling Properties of Comblike Block Copolymers with Amphiphilic Side Chains

    International Nuclear Information System (INIS)

    Surfaces of novel block copolymers with amphiphilic side chains were studied for their ability to influence the adhesion of marine organisms. The surface-active polymer, obtained by grafting fluorinated molecules with hydrophobic and hydrophilic blocks to a block copolymer precursor, showed interesting bioadhesion properties. Two different algal species, one of which adhered strongly to hydrophobic surfaces, and the other, to hydrophilic surfaces, showed notably weak adhesion to the amphiphilic surfaces. Both organisms are known to secrete adhesive macromolecules, with apparently different wetting characteristics, to attach to underwater surfaces. The ability of the amphiphilic surface to undergo an environment-dependent transformation in surface chemistry when in contact with the extracellular polymeric substances is a possible reason for its antifouling nature. Near-edge X-ray absorption fine structure spectroscopy (NEXAFS) was used, in a new approach based on angle-resolved X-ray photoelectron spectroscopy (XPS), to determine the variation in chemical composition within the top few nanometers of the surface and also to study the surface segregation of the amphiphilic block. A mathematical model to extract depth-profile information from the normalized NEXAFS partial electron yield is developed

  2. Control of Protein Affinity of Bioactive Nanocellulose and Passivation Using Engineered Block and Random Copolymers.

    Science.gov (United States)

    Vuoriluoto, Maija; Orelma, Hannes; Zhu, Baolei; Johansson, Leena-Sisko; Rojas, Orlando J

    2016-03-01

    We passivated TEMPO-oxidized cellulose nanofibrils (TOCNF) toward human immunoglobulin G (hIgG) by modification with block and random copolymers of poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) and poly(oligo(ethylene glycol) methyl ether methacrylate) (POEGMA). The block copolymers reversibly adsorbed on TOCNF and were highly effective in preventing nonspecific interactions with hIgG, especially if short PDMAEMA blocks were used. In such cases, total protein rejection was achieved. This is in contrast to typical blocking agents, which performed poorly. When an anti-human IgG biointerface was installed onto the passivated TOCNF, remarkably high affinity antibody-antigen interactions were observed (0.90 ± 0.09 mg/m(2)). This is in contrast to the nonpassivated biointerface, which resulted in a significant false response. In addition, regeneration of the biointerface was possible by low pH aqueous wash. Protein A from Staphylococcus aureus was also utilized to successfully increase the sensitivity for human IgG recognition (1.28 ± 0.11 mg/m(2)). Overall, the developed system based on TOCNF modified with multifunctional polymers can be easily deployed as bioactive material with minimum fouling and excellent selectivity. PMID:26844956

  3. Effect of Increasing Molecular Weight on the A and B blocks of a Single-ion-conducting Block Copolymer Electrolyte for Lithium Batteries

    Science.gov (United States)

    Rojas, Adriana; Inceoglu, Sebnem; Thakker, Kanav; Mackay, Nikolaus; Balsara, Nitash

    Single-ion-conducting block copolymer electrolytes are desirable for lithium metal batteries due to their ability to eliminate salt concentration gradients across the electrolyte; i.e., the lithium ion transference number is approximately unity. A series of poly(ethylene oxide)- b-poly(styrenesulfonyllithium(trifluoromethylsulfonyl)imide) (PEO- b-PSLiTFSI) copolymers was studied wherein the molecular weights of both blocks were varied. Small angle x-ray scattering and ac impedance spectroscopy were used to probe the dependence of ionic conductivity on morphology. Preliminary work suggests that increasing the molecular weights of the blocks results in increased disorder and lower conductivity.

  4. Magnetic core–bilayer shell complex of magnetite nanoparticle stabilized with mPEG–polyester amphiphilic block copolymer

    International Nuclear Information System (INIS)

    In this article, we report the synthesis of magnetite nanoparticles (Fe3O4) coated with methoxy poly(ethylene glycol) (mPEG)–polyester amphiphilic block copolymers. The coating polymer layer contains a hydrophobic inner layer of polyester and a hydrophilic corona of mPEG. The copolymers were first prepared via a direct condensation between diacid, diol compounds and mPEG oligomer to obtain a hydrophobic polyester block and hydrophilic mPEG block and then “grafted onto” a magnetite nanoparticle surface. The copolymer composition was varied by changing the structure of the diacid, diol, and the molecular weight ( M-bar n ) of the mPEG such that particles with good dispersibility and stability in water were obtained. It was found that the copolymer prepared from 1,6-hexanediol can effectively stabilize the particles in water regardless of the types of diacid and M-bar n of mPEG used. The particle size was approximately 10 nm in diameter, and the particle dispersibility in water was quite dependent on the type and concentration of the copolymer used. Thermogravimetric analysis revealed the presence of less than 37 % Fe3O4 and about 48–53 % of the copolymer in the complexes. The percent entrapment efficiency and loading efficiency of indomethacin model drug in the copolymer-coated magnetite nanoparticles were 19 and 77 %, respectively

  5. Self-assembly of block copolymers grafted onto a flat substrate: Recent progress in theory and simulations

    Science.gov (United States)

    Zheng, Wang; Bao-Hui, Li

    2016-01-01

    Block copolymers are a class of soft matter that self-assemble to form ordered morphologies on the scale of nanometers, making them ideal materials for various applications. These applications directly depend on the shape and size of the self-assembled morphologies, and hence, a high degree of control over the self-assembly is desired. Grafting block copolymer chains onto a substrate to form copolymer brushes is a versatile method to fabricate functional surfaces. Such surfaces demonstrate a response to their environment, i.e., they change their surface topography in response to different external conditions. Furthermore, such surfaces may possess nanoscale patterns, which are important for some applications; however, such patterns may not form with spun-cast films under the same condition. In this review, we summarize the recent progress of the self-assembly of block copolymers grafted onto a flat substrate. We mainly concentrate on the self-assembled morphologies of end-grafted AB diblock copolymers, junction point-grafted AB diblock copolymers (i.e., Y-shaped brushes), and end-grafted ABA triblock copolymers. Special emphasis is placed on theoretical and simulation progress. Project supported by the National Natural Science Foundation of China (Grant Nos. 20990234, 20925414, and 91227121), the Program for Changjiang Scholars and Innovative Research Team in University, China (Grant No. IRT1257), the Programme of Introducing Talents of Discipline to Universities, China, and by the Tianhe No. 1, China.

  6. Magnetic core–bilayer shell complex of magnetite nanoparticle stabilized with mPEG–polyester amphiphilic block copolymer

    Energy Technology Data Exchange (ETDEWEB)

    Mekkapat, Supachai; Thong-On, Bandit; Rutnakornpituk, Boonjira; Wichai, Uthai; Rutnakornpituk, Metha, E-mail: methar@nu.ac.th [Naresuan University, Department of Chemistry and Center of Excellence for Innovation in Chemistry, Faculty of Science (Thailand)

    2013-11-15

    In this article, we report the synthesis of magnetite nanoparticles (Fe{sub 3}O{sub 4}) coated with methoxy poly(ethylene glycol) (mPEG)–polyester amphiphilic block copolymers. The coating polymer layer contains a hydrophobic inner layer of polyester and a hydrophilic corona of mPEG. The copolymers were first prepared via a direct condensation between diacid, diol compounds and mPEG oligomer to obtain a hydrophobic polyester block and hydrophilic mPEG block and then “grafted onto” a magnetite nanoparticle surface. The copolymer composition was varied by changing the structure of the diacid, diol, and the molecular weight ( M-bar {sub n} ) of the mPEG such that particles with good dispersibility and stability in water were obtained. It was found that the copolymer prepared from 1,6-hexanediol can effectively stabilize the particles in water regardless of the types of diacid and M-bar {sub n} of mPEG used. The particle size was approximately 10 nm in diameter, and the particle dispersibility in water was quite dependent on the type and concentration of the copolymer used. Thermogravimetric analysis revealed the presence of less than 37 % Fe{sub 3}O{sub 4} and about 48–53 % of the copolymer in the complexes. The percent entrapment efficiency and loading efficiency of indomethacin model drug in the copolymer-coated magnetite nanoparticles were 19 and 77 %, respectively.

  7. Orthogonal Synthesis of Block Copolymer via Photoinduced CuAAC and Ketene Chemistries.

    Science.gov (United States)

    Tasdelen, Mehmet Atilla; Taskin, Omer Suat; Celik, Cumali

    2016-03-01

    A novel route for the synthesis of poly(ethylene glycol)-b-polystyrene copolymer, starting from commercially available poly(ethylene glycol) methyl ether and azido terminated polystyrene prepared by atom transfer radical polymerization and subsequent nucleophilic substitution, is applied with simplicity and high efficiency. The combination of photoinduced copper (I)-catalyzed alkyne-azide cycloaddition (CuAAC) and ketene chemistry reactions proceeds either simultaneously or sequentially in a one-pot procedure under near-visible light irradiation. In both cases, excellent block copolymer formations are achieved, with an average molecular weight of around 7000 g mo1(-1) and a polydispersity index of 1.20. PMID:26847166

  8. Droplet synthesis of well-defined block copolymers using solvent-resistant microfluidic device.

    Science.gov (United States)

    Hoang, Phan Huy; Nguyen, Chi Thanh; Perumal, Jayakumar; Kim, Dong-Pyo

    2011-01-21

    Well-defined diblock copolymers were synthesized via an exothermic RAFT route by a droplet microfluidic process using a solvent-resistant and thermally stable fluoropolymer microreactor fabricated by a non-lithographic embedded template method. The resulting polymers were compared to products obtained from continuous flow capillary reactor and conventional bulk synthesis. The droplet based microreactor demonstrated superior molecular weight distribution control by synthesizing a higher molecular weight product with higher conversion and narrow polydispersity in a much shorter reaction time. The high quality of the as-synthesized block copolymer PMMA-b-PS led to a generation of micelles with a narrow size distribution that could be used as a template for well-ordered mesoporous silica with regular frameworks and high surface areas. PMID:21072416

  9. Synthesis of β-cyclodextrin-Based Star Block Copolymers with Thermo-Responsive Behavior

    Directory of Open Access Journals (Sweden)

    Agnes Wycisk

    2015-05-01

    Full Text Available Star polymers are one example of three-dimensional macromolecules containing several arms with similar molecular weight connected to a central core. Due to their compact structure and their enhanced segment density in comparison to linear polymers of the same molecular weight, they have attracted significant attention during recent years. The preparation of block-arm star copolymers with a permanently hydrophilic block and an “environmentally” sensitive block, which can change its nature from hydrophilic to hydrophobic, leads to nanometer-sized responsive materials with unique properties. These polymers are able to undergo a conformational change or phase transition as a reply to an external stimulus resulting in the formation of core–shell nanoparticles, which further tend to aggregate. Star-shaped copolymers with different cores were synthesized via atom transfer radical polymerization (ATRP. The core-first method chosen as synthetic strategy allows good control over the polymer architecture. First of all the multifunctional initiators were prepared by esterification reaction of the hydroxyl groups with 2-chloropropionyl chloride. Using β-cyclodextrin as core molecules, which possess a well-defined number of functional groups up to 21, allows defining the number of arms per star polymer. In order to prepare stimuli-responsive multi-arm copolymers, containing a stimuli-responsive (poly(N-isopropylacrylamide (PNIPAAm and a non-responsive block (poly(N,N-dimethylacrylamide (PDMAAm, consecutive ATRP was carried out. The polymers were characterized intensively using NMR spectroscopy and size exclusion chromatography (SEC, whereas the temperature-depending aggregation behavior in aqueous solution was determined via turbidimetry and differential scanning calorimetry (DSC.

  10. Synthesis of PMMA-b-PU-b-PMMA tri-block copolymers through ARGET ATRP in the presence of air

    Directory of Open Access Journals (Sweden)

    P. Krol

    2013-03-01

    Full Text Available ARGET (activators regenerated by electron transfer ATRP (atom transfer radical polymerization has been successfully performed (in flasks fitted with rubber septa without the need for use of Schlenk line in the presence of limited amount of air and with a very small (370 ppm amount of copper catalyst together with an appropriate reducing agent Cu(0. Novelty of this work is that the poly(methyl methacrylate-block-polyurethane-block-poly(methyl methacrylate triblock copolymers were synthesized for the first time through ARGET ATRP, by using tertiary bromine-terminated polyurethane as a macroinitiator (MBP-PU-MBP, CuBr2 or CuCl2 as a catalyst and N,N,N',N",N"-pentamethyldiethylenetriamine (PMDETA or 2,2'-bipyridine (Bpy as a complexing agent. As the polymerization time increases, both the monomer conversion and ln([M]0/[M] increased and the molecular weight of copolymer increases linearly with increasing conversion. Theoretical number-average molecular weight (Mn, th of the tri-block copolymers was found to be comparable with number-average molecular weight determined by GPC analyses (Mn, GPC. These results indicate that the formation of the tri-block copolymers was through atom transfer radical polymerization mechanism. 1H and 13C NMR spectral methods were employed to confirm chemical structures of synthesized macroinitiator and tri-block copolymers. Mole percentage of PMMA in the tri-block copolymers was calculated using 1H NMR spectroscopy and was found to be comparable with the GPC results. Additionally, the studies of surface properties (confocal microscopy and SFE of tri-block copolymer coatings confirmed the presence of MMA segments.

  11. Effect of Lithium Ion Concentration of a Single-Ion-Conducting Block Copolymer Electrolyte on the Morphology-Conductivity Relationship

    Science.gov (United States)

    Rojas, Adriana A.; Inceoglu, Sebnem; Mackay, Nikolaus G.; Devaux, Didier; Stone, Greg; Balsara, Nitash

    2015-03-01

    Single-ion-conducting electrolytes are desirable for lithium metal batteries because they enable the sole conduction of lithium ions, the reacting species in lithium batteries; hence, they avert detrimental battery limitations due to salt concentration gradients. A single-ion-conducting block copolymer electrolyte, poly(ethylene oxide)-b-polystyrenesulfonyllithium (trifluoromethyl sulfonyl) imide (PEO-b-PSLiTFSI), was characterized in-situ and ex-situ for its ionic conductivity and morphology using AC impedance spectroscopy and small angle x-ray scattering, respectively. This work is the first to elucidate the relationship between the two properties in a single-ion block copolymer electrolyte. The transference number for the copolymers was determined to be greater than or equal to 0.87, indicating that to a good approximation, the block copolymers are single-ion conducting electrolytes. It was found that increasing the molecular weight of the PSLiTFSI block led to an increase in the extent of block copolymer block-mixing and a change in the conductivity profile from discontinuous to continuous. These effects can be attributed to the disruption of PEO crystallization, which was shown to drive microphase separation. Joint Center for Energy Storage Research, Lawrence Berkeley National Laboratory.

  12. Spontaneous condensation in DNA-polystyrene- b-poly(l-lysine) polyelectrolyte block copolymer mixtures

    Science.gov (United States)

    Castelletto, V.; Hamley, I. W.; Kerstens, S. L. H.; Deacon, S.; Thomas, C. D.; Lübbert, A.; Klok, H.-A.

    2006-05-01

    We investigated the condensation of calf thymus DNA by amphiphilic polystyrenem-b-poly(l-lysine)n block copolymers ( PSm-b- PLysn, m, n = degree of polymerization), using small-angle X-ray scattering, polarized optical microscopy and laser scanning confocal microscopy. Microscopy studies showed that the DNA condenses in the form of fibrillar precipitates, with an irregular structure, due to electrostatic interactions between PLys and DNA. This is not modified by the presence of hydrophobic PS block. Scattering experiments show that the structure of the polyplexes corresponds to a local order of DNA rods which becomes more compact upon increasing n. It can be concluded that for DNA/ PSm-b- PLysn polyplexes, the balance between the PLys block length and the excess charge in the system plays an essential role in the formation of a liquid crystalline phase.

  13. Low Molecular Weight pDMAEMA-block-pHEMA Block-Copolymers Synthesized via RAFT-Polymerization: Potential Non-Viral Gene Delivery Agents?

    OpenAIRE

    Thomas Kissel; Christian Pfeiffer; Olga Samsonova; Markus Hellmund; Merkel, Olivia M.

    2011-01-01

    The aim of this study was to investigate non-viral pDNA carriers based on diblock-copolymers consisting of poly(2-(dimethyl amino)ethyl methacrylate) (pDMAEMA) and poly(2-hydroxyethyl methacrylate) (pHEMA). Specifically the block-lengths and molecular weights were varied to determine the minimal requirements for transfection. Such vectors should allow better transfection at acceptable toxicity levels and the entire diblock-copolymer should be suitable for renal clearance. For this purpose, a ...

  14. SYNTHESIS AND CHARACTERIZATION OF LIQUID CRYSTALLINE MULTI-BLOCK COPOLYMERS,POLY[1,6-BIS(4-OXYBENZOYL-OXY)HEXANE TEREPHTHALATE]-b-BISPHENOL A POLYCARBONATE

    Institute of Scientific and Technical Information of China (English)

    Hui-qing Zhang; Xiong-yan Zhao; De-shan Liu; Qi-xiang Zhou

    1999-01-01

    A series of liquid crystalline multi-block copolymers poly[1,6-bis(4-oxybenzoyl-oxy)hexane terephthalate]-b-bisphenol A polycarbonate (PHTH-6-b-PC) with different segment lengths were synthesized in tetrachloroethane by solution polycondensation in which hydroxyl terminated PC and acyl chloride terminated PHTH-6 were used. It is found that block copolymers with high molecular weight and welldefined structures were obtained. All the block copolymers exhibit a nematic liquid crystalline texture.

  15. Ultra-thin films based on random copolymers containing perfluoropolyether side chains

    International Nuclear Information System (INIS)

    Random copolymers were synthesised by copolymerizing methylmethacrylate and perfluoropolyetherurethanemethacrylate monomers, differing for the structural unit of the fluorinated chain, its end group and its molecular weight. The copolymers obtained had similar molecular weight and polydispersity, with a fluorine content between 5 and 10% wt/wt; they showed remarkable features such as biphasicity with coexistence of soft domains made of the perfluoropolyether chains and hard domains due to the methylmethacrylate backbone: the glass transition temperature Tg of the soft and hard phases was Tg1 g2 ≅ 110 °C respectively. All the copolymers were highly hydrophobic: water contact angle was always higher than 105°. The copolymers were used for the preparation of ultra thin films by spin coatings: by atomic force microscopy and X-ray reflectivity the thickness was found in the range of 20–400 Å depending on the spinning conditions, in particular the concentration of the spun solutions. The films were also highly smooth, with a roughness lower than 5 Å. - Highlights: ► We describe random methacrylic copolymers with perfluoropolyether side chain. ► The copolymers had a fluorine content of 5–10% wt/wt. ► The copolymers were spin coated and formed hydrophobic films. ► The film thickness was in the range of 20–400 Å. ► The coatings' roughness was always lower than 5 Å.

  16. Binding of amphiphilic and triphilic block copolymers to lipid model membranes: the role of perfluorinated moieties.

    Science.gov (United States)

    Schwieger, Christian; Achilles, Anja; Scholz, Sven; Rüger, Jan; Bacia, Kirsten; Saalwaechter, Kay; Kressler, Jörg; Blume, Alfred

    2014-09-01

    A novel class of symmetric amphi- and triphilic (hydrophilic, lipophilic, fluorophilic) block copolymers has been investigated with respect to their interactions with lipid membranes. The amphiphilic triblock copolymer has the structure PGMA(20)-PPO(34)-PGMA(20) (GP) and it becomes triphilic after attaching perfluoroalkyl moieties (F9) to either end which leads to F(9)-PGMA(20)-PPO(34)-PGMA(20)-F(9) (F-GP). The hydrophobic poly(propylene oxide) (PPO) block is sufficiently long to span a lipid bilayer. The poly(glycerol monomethacrylate) (PGMA) blocks have a high propensity for hydrogen bonding. The hydrophobic and lipophobic perfluoroalkyl moieties have the tendency to phase segregate in aqueous as well as in hydrocarbon environments. We performed differential scanning calorimetry (DSC) measurements on polymer bound lipid vesicles under systematic variation of the bilayer thickness, the nature of the lipid headgroup, and the polymer concentration. The vesicles were composed of phosphatidylcholines (DMPC, DPPC, DAPC, DSPC) or phosphatidylethanolamines (DMPE, DPPE, POPE). We showed that GP as well as F-GP binding have membrane stabilizing and destabilizing components. PPO and F9 blocks insert into the hydrophobic part of the membrane concomitantly with PGMA block adsorption to the lipid headgroup layer. The F9 chains act as additional membrane anchors. The insertion of the PPO blocks of both GP and F-GP could be proven by 2D-NOESY NMR spectroscopy. By fluorescence microscopy we show that F-GP binding increases the porosity of POPC giant unilamellar vesicles (GUVs), allowing the influx of water soluble dyes as well as the translocation of the complete triphilic polymer and its accumulation at the GUV surface. These results open a new route for the rational design of membrane systems with specific properties. PMID:24942348

  17. High quality sub-10 nm graphene nanoribbons by on-chip PS-b-PDMS block copolymer lithography

    DEFF Research Database (Denmark)

    Rasappa, Sozaraj; Caridad, Jose; Schulte, Lars;

    2015-01-01

    Block copolymer self-assembly holds great promise as a rapid, cheap and scalable approach to nanolithography. We present a straightforward method for fabrication of sub-10 nm line patterns from a lamellar polystyrene-b-polydimethylsiloxane (SD) block copolymer with total average molecular weight of...... block and the graphene under PS. Raman analysis supports the formation of graphene nanoribbons with an average distance between defects corresponding to the oxidized PDMS pitch, with no sign of defects generated in the ribbon channel. This suggests a high degree of protection of the nanoribbons by the...

  18. Morphology and Dynamic Mechanical Properties of Styrene Containing Tri-Block Copolymers for Electromagnetic Wave Interaction Applications

    Science.gov (United States)

    Peddini, S.; Mauritz, K.; Nikles, D.; Weston, J.

    2008-03-01

    Styrene containing triblock copolymers, namely poly(styrene-ethylene/butylene-styrene) (SEBS) and poly(styrene-butadiene-styrene)] (SBS), were selectively modified by attaching polar groups to facilitate the in-growth of an inorganic component. In case of SEBS, the styrene block was sulfonated, and in SBS, the butadiene block was hydroxylated. The extent of modification was determined by analytical and spectroscopic methods. This presentation shows the morphology and dynamical mechanical properties of both block copolymers before and after modification. Nanocomposites of these block copolymers were prepared by inclusion of magnetic metal oxides via an in-situ precipitation and self assembly processes and their morphology and dynamical mechanical properties were studied. Magnetic properties of these polymers filled with iron oxide nanoparticles were measured using an alternating gradient magnetometer (AGM) at room temperature to observe the magnetic hysteresis.

  19. Simultaneous Photoinduced ATRP and CuAAC Reactions for the Synthesis of Block Copolymers.

    Science.gov (United States)

    Murtezi, Eljesa; Yagci, Yusuf

    2014-09-01

    Atom transfer radical polymerization (ATRP) and copper-catalyzed azide-alkyne cycloaddition (CuAAC) reactions, both utilizing copper(I) (Cu(I)) complexes, make a tremendous progress in synthetic polymer chemistry. Independently or in combination with other polymerization processes, they give access to the synthesis of polymers with well-defined structures, desired molecular architectures, and a wide variety of functionalities. Here, a novel in situ photoinduced formation of block copolymers is described by simultaneous ATRP and CuAAC processes. This approach relies on the direct reduction of initially charged copper(II) complexes to Cu(I) complexes to trigger both ATRP and CuAAC reactions coinciding under UV light at ambient temperature in one pot. Its synthetic utility is demonstrated on a model block copolymerization process by photoinduced ATRP of methyl methacrylate (MMA) using an initiator possessing acetylene functionality and concomitant click reaction between thus formed α-acetylene-poly(methyl methacrylate) (Ac-PMMA) and independently prepared azide functional polystyrene (PS-N3 ). Successful formation of PS-b-PMMA block copolymer is confirmed by FT-IR and (1) H NMR spectral analysis and gel permeation chromatography (GPC) measurements. PMID:25200624

  20. Polydispersity-Driven Block Copolymer Amphiphile Self-Assembly into Prolate-Spheroid Micelles

    Energy Technology Data Exchange (ETDEWEB)

    Schmitt, Andrew L.; Repollet-Pedrosa, Milton H.; Mahanthappa, Mahesh K. (UW)

    2013-09-26

    The aqueous self-assembly behavior of polydisperse poly(ethylene oxide-b-1,4-butadiene-b-ethylene oxide) (OBO) macromolecular triblock amphiphiles is examined to discern the implications of continuous polydispersity in the hydrophobic block on the resulting aqueous micellar morphologies of otherwise monodisperse polymer surfactants. The chain length polydispersity and implicit composition polydispersity of these samples furnishes a distribution of preferred interfacial curvatures, resulting in dilute aqueous block copolymer dispersions exhibiting coexisting spherical and rod-like micelles with vesicles in a single sample with a O weight fraction, w{sub O}, of 0.18. At higher w{sub O} = 0.51-0.68, the peak in the interfacial curvature distribution shifts and we observe the formation of only American football-shaped micelles. We rationalize the formation of these anisotropically shaped aggregates based on the intrinsic distribution of preferred curvatures adopted by the polydisperse copolymer amphiphiles and on the relief of core block chain stretching by chain-length-dependent intramicellar segregation.