WorldWideScience

Sample records for bituminous bases

  1. Bituminization plant Jaslovske Bohunice

    International Nuclear Information System (INIS)

    In this leaflet the principle of the bituminization plant for radioactive concentrate (the intermediate liquid radioactive waste generated during the NPP A1, V-1, V-2 operations) solidification used in the Bohunice Radwaste Treatment Centre (BSC RAO) is presented

  2. Cold bituminous mixes

    OpenAIRE

    Delak, Boštjan

    2012-01-01

    Asphalt mix (short also asphalt) can be obtained from nature (natural asphalt) or produced technically (artificial asphalt), i. e. as a mix of bituminous binder, stone grain, and other additives that improve the asphalt properties. The beginnings of the use of asphalt can be traced from 6,000 to 4,000 BC since people back then knew some materials that contained bitumen as a binder. A more frequent use of the natural asphalt, however, starts around 3,000 BC. Different peoples used it primar...

  3. Parametric and dynamic studies of an iron-based 25-kWth coal direct chemical looping unit using sub-bituminous coal

    International Nuclear Information System (INIS)

    Highlights: • Integrated, moving bed chemical looping reactor with iron-oxide based oxygen carrier. • Coal carbon conversion from 84.8% to 99.9%, thermal capacity 7.4 to 27.7 kWth, O2 demand less than 1.3%. • Dynamic temperature of moving bed reducer is established and tracked during coal injection. • CH4 and CO present at initial coal injection, eliminated after oxygen carrier activated. • Lower coal injection had higher volatiles residence time and conversion. - Abstract: The iron-based Coal-Direct Chemical Looping (CDCL) combustion process is an alternative to conventional oxy-combustion technologies, where the oxygen used for fuel conversion in the CDCL process is provided by an iron-oxide based oxygen carrier instead of an air separation unit. The iron oxide is reduced using coal in the reducer reactor, producing highly-pure CO2 in the flue gas, and the reduced iron oxide is regenerated in a separate combustor reactor using air. The CDCL process at Ohio State has been developed and demonstrated in a 25 kWth sub-pilot unit, and it is the first chemical looping demonstration unit with a circulating moving bed reactor for solid fuel conversion. To date, the CDCL sub-pilot unit at OSU has been operated for more than 680 h, with a 200-h continuous operation, providing important data on long term operability as well as parametric optimization. This paper discusses recent parametric operational experience with sub-bituminous coal as the fuel, where dynamic changes in variables were performed to observe the effects on the unit itself. Measurements included temperature, pressure, and gas concentrations from the reducer and combustor. Furthermore, effects of different variables, such as flue gas recycle ratios (enhancer gas flow rates), feed port injection, and temperature, were observed. Tests confirmed high coal conversions with high purity of CO2 achieved in the flue gas. Overall, the moving bed design of the reducer results in nearly full coal conversion

  4. Crumb Rubber in cold recycled bituminous mixes

    DEFF Research Database (Denmark)

    Dondi, Giulio; Tataranni, Piergiorgio; Pettinari, Matteo;

    2014-01-01

    . Cold recycling is, among the recycling techniques, certainly the most studied and developed: it allows the recovering of bituminous material from an existing pavement without the addition of heat, whilst ensuring the creation of high quality bound base layers. A wide range of materials have been tested...... together with Reclaimed Asphalt Pavement (RAP) and, consequently, there is a large number of variables that can be considered in the mix-design process of new eco-friendly Cold Recycled Mixes. In particular, the present research involves the use of Crumb Rubber within a mixture containing 100% Reclaimed...... Asphalt Pavement, cold recycled with bitumen emulsion and cement. Two different Crumb Rubbers were adopted: one from the ambient production method, and one produced with the cryogenic process. The goal of this research project was to analyze and evaluate the different physical and mechanical...

  5. Radon concentration measurements in bituminous coal mines

    International Nuclear Information System (INIS)

    Radon measurements were carried out in Kozlu, Karadon and Uezuelmez underground coal mines of Zonguldak bituminous coal basin in Turkey. Passive-time integrating method, which is the most widely used technique for the measurement of radon concentration in air, was applied by using nuclear etched track detectors (CR-39) in the study area. The radon concentration measurements were performed on a total of 42 points in those three mines. The annual exposure, the annual effective dose and lifetime fatality risk, which are the important parameters for the health of workers, were estimated based on chronic occupational exposure to the radon gas, which is calculated using UNCEAR-2000 and ICRP-65 models. The radon concentrations at several coal production faces are higher than the action level of 1000 Bq m-3. It is suggested that the ventilation rates should be rearranged to reduce the radon concentration. (authors)

  6. Leachability of bituminized radioactive waste. Literature survey

    International Nuclear Information System (INIS)

    Bituminized radioactive waste that will be returned from COGEMA, France is planned to be disposed of in deep geologic repository in Japan. Data on leachability of radionuclides from bituminized waste are required for the performance assessment of the disposal. We made a literature survey on bitumen and bituminized radioactive waste, placing emphasis on leach tests and leach data in terms of geologic disposal. This survey revealed that reliable leach data on transuranium elements and data obtained under reducing conditions that is characteristic to deep underground are lacking. (author). 64 refs

  7. Bituminous reference document: synthesis of knowledge on the long time behavior of bituminous packages

    International Nuclear Information System (INIS)

    This document is a synthesis of the knowledge acquired at the CEA on the behavior of bituminous packages. In this framework, the CEA studied bituminous packages in generic conditions of a package lifetime. The main factors, the evolution mechanisms and influential parameters have been determined and quantitative s simulation have been developed. After a description of the main initial bituminous packages characterizations, the evolutions in saturated and un-saturated environment are exposed. (A.L.B.)

  8. 30 CFR 716.4 - Special bituminous coal mines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Special bituminous coal mines. 716.4 Section... INTERIOR INITIAL PROGRAM REGULATIONS SPECIAL PERFORMANCE STANDARDS § 716.4 Special bituminous coal mines. (a) Definition. Special bituminous coal surface mines as used in this section means those...

  9. Wetting of bituminized ion-exchangers under simulated repository conditions

    International Nuclear Information System (INIS)

    According to the present plans the spent nuclear fuel from four Finnish nuclear power units will be transferred after interim storage to the final disposal site where it will be encapsulated and disposed of in a final repository constructed into the bedrock at a depth of 500 meters. Low and medium level waste generated at nuclear power plants will be finally disposed of in caverns constructed in the bedrock at the power plant site. The safety of the final disposal is based on a multibarrier concept and the degree of safety is estimated by using predictive models. The properties of the waste form are taken into account in the design of the repository construction. Bitumen has been chosen as an immobilisation agent for the wet wastes at Olkiluoto Power Plant, where two BWR units, TVO 1 and TVO 2, have separate bituminization facilities designed by Asea-Atom. Properties of bituminized spent ion-exchange resins from Olkiluoto power plant have been studied by VTT Chemical Technology since the late 70's. These studies have concentrated mainly on determining the long-term behaviour of the bituminization product under the repository conditions. Current interest lies on wetted product as a diffusion barrier. For this purpose a microscopic method for the visualisation of the structure of the wetted product has been developed. The equilibration of the samples in simulated concrete groundwater is currently going on at a temperature of 5-8 deg. C. Preliminary results are presented in this paper. Diffusion experiments have been planned for the further characterising of the wetted product as a release barrier for radionuclides including modelling. (author)

  10. Global market trade policy analysis for petroleum oils and oils obtained from bituminous minerals, crude

    Directory of Open Access Journals (Sweden)

    Bagheri, F.

    2012-01-01

    Full Text Available This article is based on surveying the custom tariffs imposed on the world export market of Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude. We obtained the data according to the most updated available data provided online by UNCTAD and World Bank. The results indicate that none of the 142 countries in the world market of this product have imposed non-tariff trade barriers on the import of Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude. The developed countries and the countries with transition economies are the main world import partners. European Union, United States, China, Japan, South Korea, Canada, Singapore, Taiwan, Thailand, South Africa, Australia, Turkey, Brazil, Sweden and Belarus are the examples and have imposed low custom tariffs on Petroleum Oils and Oils Obtained from Bituminous Minerals, Crude.

  11. Study of stabilization/solidification processes (of solid porous wastes) based on hydraulic or bituminous binders; Etude des procedes de stabilisation/solidification (des dechets solides poreux) a base de liants hydrauliques ou de liants bitumineux

    Energy Technology Data Exchange (ETDEWEB)

    Sing-Teniere, Ch.

    1998-02-01

    The first part of this thesis presents the regulatory framework and the technical context linked with the study of stabilized/solidified wastes and with the evaluation of stabilization/solidification processes. A presentation of the two type of ultimate wastes under study (a used catalyst and an activated charcoal) and an analysis of the processes is given. The second part is devoted to the experimental characterization of both types of porous wastes. The third part deals with the processing of such wastes using an hydraulic binder. The study stresses on both on the stabilization/solidification efficiency of the process and on the conditions of its implementation. The same work is made for a process that uses a bituminous binder. Some choice criteria for the selection of the better process are deduced from the examination of the overall data collected. The waste characterization methodology is applied six times: two times for the raw wastes, two times for the same wastes processed with an hydraulic binder, and two times for the same wastes processed with a bituminous binder. (J.S.)

  12. Evaluating Self Healing Capability of Bituminous Mastics

    OpenAIRE

    Qiu, J.; Ven, M. van de; Wu, S.; Yu, J.; Molenaar, A.

    2012-01-01

    The self-healing capability of bituminous materials has been known for many years. Researches were mostly focused on the self healing behaviour during load repetitions. The tests are either time consuming and/or complex. In this paper, a simple self healing test procedure is presented combining the fracture-healing-re-fracture test (FHR) with morphological observations. A fast displacement speed loading was applied first to produce a flat open crack with a crack width of 100–200 μm. Then the ...

  13. Skid resistance of bituminous surfaces in Ohio

    Science.gov (United States)

    Colony, D. C.

    1984-03-01

    Statistical studies of skid number (SN) on the state highway system in Ohio reveal apparently systematic variations in distributions of SN among the twelve districts in the state. These variations appear to be significantly related to traffic and to geological characteristics of a given district. Regression calculations using traffic index, a function of ADT and age of the pavement surface in months, show a high correlation with SN, although standard errors of estimate were too large to make the equations useful for predicting SN from traffic variables. Similar results were obtained by elating SN to physiographic features in the state. Pavement surface type (bituminous or pcc) and coarse aggregate type (limestone, gravel or slag) are significantly related to SN.

  14. Development of non-standard equipment of bituminization line

    International Nuclear Information System (INIS)

    A brief description is presented of some components of the bituminization line developed at the Research Institute of Chemical Installations in Brno. The film rotor evaporator has an evaporation area of 2 m2. The mixing tank is the main technological assembly for processing loose materials, i.e., sorbents and fly ash which it mixes with melted bitumen. The screw conveyor with a three-way valve is designed for batching the dried radioactive sorbent and fly ash into mixing tanks. Attention is also devoted to certain systems of measurement and control of the bituminization line, namely to measurement of the level of the bituminization product, the flow rate of bituminization emulsion and the water-sorbent mixture and to the diagnostics of failure and accident conditions of the film rotor evaporator. (Z.M.)

  15. Bituminous and asphaltic membranes for radioactive waste repositories on land

    International Nuclear Information System (INIS)

    The aim of the study has been to identify, within generic designs for waste facilities, areas where bituminous materials might be incorporated as a barrier. The report is presented in three sections: Part I - The properties of bitumen are described, with particular reference to the long-term behaviour of the material. The durability of bitumen is discussed, including aspects such as ageing, microbial degradation, chemical resistance and radiation resistance. Part II -The use of bituminous materials in hydraulic engineering is outlined. Much of this section of the report concentrates on the use of bituminous materials in embankment dams and reservoir construction. A review of material technology and construction techniques is presented and a detailed assessment made of the performance of the materials in service. Part III - Generic trench type radioactive waste repository designs incorporating bituminous materials are presented. Material and construction specifications for the designs are detailed, and a performance assessment presented. (author)

  16. Long-term properties of bituminized waste products

    International Nuclear Information System (INIS)

    This study is a survey of the factors of importance for long term behaviour of bituminized ion exchange resins. Phenomena occurring in bituminized waste products affected by the treatment, storage and disposal are identified. Test methods have been developed for characterizing product properties, which are important for the long-term behaviour. The long-term properties of bituminized ion-exchange resins are studied in a repository environment with access of water equilibrated with concrete. In these circumstances the most important properties are ralated to the interactions of bituminized waste with the surrounding barriers. The most important phenomena are water uptake due to rehydration of the resins and subsequent swelling of the product. (author)

  17. Long-term properties of bituminized waste products

    International Nuclear Information System (INIS)

    This study is a survey of the factors of importance for the long term behaviour of bituminized ion exchange resins. Phenomena occurring in bituminized waste products affected by the treatment, storage and disposal are identified. Test methods have been developed for characterizing product properties, which are important for the long-term behaviour. The long-term properties of bituminized ion-exchange resins are studied in a repository environment with access of water equilibrated with concrete. In these circumstances the most important properties are related to the interactions of bituminized waste with the surrounding barriers. The most important phenomena are water uptake due to rehydration of the resins and subsequent swelling of the product

  18. Effects of bituminous layer as backfill material on mechanical behavior in tunnel model

    OpenAIRE

    Moriyoshi, Akihiro; Takano, Shin-ei; Urata, Hiroyuki; Suzuki, Tetsuya; Yoshida, Takaki

    2001-01-01

    This paper describes the effects of bituminous material as a backfill material on mechanical behavior in model tunnel in laboratory. It is known that load spreading and relaxation of bituminous material are good properties. Then if we use bituminous material as a backfill material of tunnel, the tunnel will have waterproof, good load spreading property. We used new bituminous material (Aquaphalt) which can solidify in water. We conducted relaxation test in tension for new bituminous mat...

  19. The bituminous sands : a Canadian mirage?

    Energy Technology Data Exchange (ETDEWEB)

    Rousse, D.R. [Quebec Univ., Chicoutimi, PQ (Canada). Dept. des Sciences Appliquees; Nasr, G.J. [Lebanese Univ., Roumieh (Lebanon). Faculty of Engineering; Turcotte, S.F. [Quebec Univ., Montreal, PQ (Canada). Centre d' Etudes Internationales et Mondialisation; Salah, N.B. [Ecole Superieure des Sciences et Techniques De Tunis, Tunis (Tunisia). LMMP

    2009-07-01

    This paper examined the controversy about the potential role of a significant increase in Canadian oil sands production in order to bridge the upcoming gap between the world's increasing energy demand and the total recoverable oil supply. The paper presented the actual potential of different scenarios and considered the prediction cost forecasts. A brief overview of environmental impacts and the real return on investments were also provided. Environmental impacts that were considered included land degradation; water contamination; ecosystem damage; and air pollution. Nuclear energy was also presented as a possible solution. The paper demonstrated that even in a very optimistic scenario, Canada's oil sands accelerated production has a negligible effect on the aforementioned gap, has a considerable impact on environment that has yet to be accounted for. Energy ratios that were presented included energy return on energy investment; energy available on energy used; and energy payback. It was concluded that enhanced recovery techniques are clearly needed for future sustainable exploitation of these bituminous sands. 32 refs., 1 fig.

  20. Long-term behavior of bituminized waste: modelling of auto-irradiation and leaching

    International Nuclear Information System (INIS)

    During interim storage, the main evolution factor of the bituminized wastes is radiolysis under auto-irradiation, while in deep disposal conditions, after radioactive decrease, site resaturation with water, and container corrosion, the main factor of evolution is leaching by water. This paper presents two models, designed to describe respectively radiolytic gas evacuation, and bituminized waste alteration under leaching. The first model is based on the integration of simple descriptions of gas production by radiolysis, gas diffusive transport, bubble nucleation and ripening, and bubble transport under buoyancy and viscosity. The second model is based on simple descriptions of water adsorption and solubilization at the surface, water diffusion into the matrix, water uptake by the most soluble salts, salt grain swelling and alteration of matrix waterproofing, diffusive transport of salts out of the waste. Copyright (2001) Material Research Society

  1. Microstructural self-healing of bituminous materials: Combined experimental and numerical study

    OpenAIRE

    Pauli, A; Schmets, A. J. M.; Kasbergen, C.; Varveri, K.; Scarpas, A.

    2013-01-01

    Bituminous materials form a class of materials that possess the intrinsic ability to selfheal. This self-healing capability is evidenced by the observation that the service life of these materials ‘in the field’ exceeds the service life as predicted by standard mechanical laboratory tests. This mismatch between laboratory prediction and field service life is usually accounted for by applying a shift or healing factor. In this contribution we demonstrate a model that is based on the observatio...

  2. Influence of properties of bituminous binders on the strength of formed coke

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Ashok K.; Das, Bani P.; Tripathi, Prem S.M. [Central Fuel Research Institute, P.O. FRI-828108, Dhanbad (India)

    2002-03-20

    The role of different chemical characteristics (coking value, quinoline insolubles, elemental composition, {beta}-resin, toluene solubles) of various coal tar- and petroleum-based bituminous binders, such as heavy fraction of HTC tar, processed LTC tar, pitch and asphalt as also the mixed binder in controlling the strength of formed coke made from char prepared from non-coking Chirimiri coal and coke breeze (prepared after carbonising Jharia coal), respectively, has been studied in some detail. The objective was to investigate as to whether and how the properties of these bituminous binders govern the strength of formed coke. It is found that these properties of the binders do play significantly important role in controlling the strength of formed coke both during curing and carbonisation. These parameters of the binders are found to be closely related with their atomic C/H ratios. Notwithstanding the varying composition of the binders of different origin, be they coal tar or petroleum based, the atomic C/H ratio seems to be the most important characteristics of the bituminous binders, upon which the strength of formed coke depends predominantly. This also holds true when mixed binders were used. The results show that at a C/H ratio of about 1, the strength of the briquettes either on curing or on carbonising remains almost similar and that strong cured briquettes can be produced by using a bituminous binder with a C/H ratio less than 1, whilst for obtaining strong carbonised briquettes, binders with C/H ratio greater than 1 are preferable.

  3. Bituminization of low- and intermediate-level radioactive concentrates

    International Nuclear Information System (INIS)

    The results and experiences are summed up from the research and development of the technology of bituminization of low- and intermediate-level radioactive concentrates generated in the operation of nuclear power plants with WWER-440 reactors. The experiments took place on a pilot plant bituminization line with various model solutions at an evaporator capacity of 70, 100 and 140 litres per hour. The composition of the solutions changed in dependence on the knowledge of the composition of actual concentrates in the V-1 nuclear power plant at Jaslovske Bohunice. The following factors were studied in the concentrate: the effect of its pH, its borate content and content of metal carbonates, the content of organic acid salts, the content of detergents, etc., on the process of bituminization. Physico-chemical conditions are described under which the operation of the evaporator was fail-safe and filling of the bituminization product with salts homogeneous. A low water content of up to 1% was achieved. The properties of the bituminization product were negatively affected by a high level of heavy metal oxides, surfactants, oxalates and citrates. In order to improve the properties of the product it will be necessary to replace bitumen emulsion Silembit-60 used as reinforcement matrix, by a different type of bitumen. (Z.M.)

  4. Fatigue and healing properties of bituminous mastics reinforced with nano-sized additives

    Science.gov (United States)

    Santagata, Ezio; Baglieri, Orazio; Tsantilis, Lucia; Dalmazzo, Davide; Chiappinelli, Giuseppe

    2016-03-01

    The research work described in the paper focused on fatigue and healing properties of bituminous mastics reinforced with nano-sized additives. Commercially available multiwall carbon nanotubes (CNTs) and montmorillonite nanoclay (NC) were combined with a single base bitumen and a standard mineral filler to produce bituminous mastics. These blends were prepared in the laboratory by making use of a technique consisting in simple shear mixing followed by sonication. Fatigue behaviour of mastics under repeated loading was investigated by means of time sweeps performed in the strain-controlled mode at various amplitudes. Healing potential was assessed by adopting a testing protocol specifically conceived to discriminate between recovery of damage induced by fatigue loading and other artefact phenomena which may affect material response. All rheological measurements were carried out with a dynamic shear rheometer in the parallel plates geometry. Outcomes of the experimental investigation were found to be highly dependent on the nature of additive type, as a result of the key role played by interaction mechanisms that nano-particles can establish within the bituminous mastic.

  5. Polygenic formation model of the planet's bituminous belts

    Science.gov (United States)

    Dmitrievsky, A. N.; Balanyuk, I. E.

    2011-05-01

    In recent years, much attention has been paid to nontraditional hydrocarbon sources. Today the portion of nontraditional gas in the world extraction is 15% or 450 billion cubic meters, which hat makes up the volume of total gas exports from Russia. As is known, the easy-prospecting oil has been already found. The innovative technologies in geophysics, drilling, and excavation and the increased extraction coefficient expect further development and industrial compliance with these requirements. Based on calculations, the world oil reserves are now one trillion of stock tank barrels and one trillion barrels have been already extracted. The evergrowing demand for energy gives rise to the necessity of searching for and extracting more oil resources, and both these aspects are unique problems. The search for profitable petroleum deposits has become more and more difficult even in the leading companies. The increment of the world resources is a key vital question; therefore, the elaboration of criteria for the discovery of nontraditional deposits take on special significance in the economic respect. The authors are working out a conception that will be a guideline for future finding of the richest oil deposits in active geodynamic zones. For the first time, we suggest the polygenic formation model of the planet's bituminous belts.

  6. Fuel properties of bituminous coal and pyrolytic oil mixture

    Science.gov (United States)

    Hamdan, Hazlin; Sharuddin, Munawar Zaman; Daud, Ahmad Rafizan Mohamad; Syed-Hassan, Syed Shatir A.

    2014-10-01

    Investigation on the thermal decomposition kinetics of coal-biooil slurry (CBS) fuel prepared at different ratios (100:0,70:30,60:40,0:100) was conducted using a Thermogravimetric Analyzer (TGA). The materials consisted of Clermont bituminous coal (Australia) and bio-oil (also known as pyrolytic oil) from the source of Empty Fruit Bunch (EFB) that was thermally converted by means of pyrolysis. Thermal decomposition of CBS fuel was performed in an inert atmosphere (50mL/min nitrogen) under non-isothermal conditions from room temperature to 1000°C at heating rate of 10°C/min. The apparent activation energy (Ea.) and pre-exponential factor (A) were calculated from the experimental results by using an Arrhenius-type kinetic model which first-order decomposition reaction was assumed. All kinetic parameters were tabulated based on the TG data obtained from the experiment. It was found that, the CBS fuel has higher reactivity than Clermont coal fuel during pyrolysis process, as the addition of pyrolytic oil will reduce the Ea values of the fuel. The thermal profiles of the mixtures showed potential trends that followed the characteristics of an ideal slurry fuel where high degradation rate is desirable. Among the mixture, the optimum fuel was found at the ratio of 60:40 of pyrolytic oil/coal mixtures with highest degradation rate. These findings may contribute to the development of a slurry fuel to be used in the vast existing conventional power plants.

  7. Measurement of heat generation from simulated bituminized product

    International Nuclear Information System (INIS)

    The fire and explosion incident occurred at Bituminization Demonstration Facility of PNC Tokai Works on March 11, 1997. In order to ascertain the cause of incident, the investigation has been pushed forward. For the investigation, we prepared simulated bituminized product of measurement of heat generation in low temperature region less than 200degC. We used calvet Calorimeter MS80 for the heat generation measurement. Result of measurement, we were able to catch the feeble heat generation from bituminized product. The maximum calorific value that was able to detect it in isothermal measurement was approximately 1 mW/g in 160degC. It was approximately 2 mW/g in 200degC. And, as the another measurement, the measurement condition went heat rate by 0.01degC/minute, the highest temperature 190degC. As a result, the maximum generation of heat value that was able to detect it was approximately 0.5 mW/g. I changed simulated bituminized products and measured these. A difference of condition is salt particle size, salt content rate (45%, 60%), addition of the simulated precipitate. But there was not a difference in the generation of heat characteristic detected. (author)

  8. Unexpectedly high uptake of palladium by bituminous coals

    Energy Technology Data Exchange (ETDEWEB)

    Lakatos, J. [Research Lab. for Mining Chemistry, Hungarian Academy of Sciences, Miskolc-Egyetemvaros (Hungary); Brown, S.D.; Snape, C.E. [Univ. of Strathclyde, Dept. of Pure and Applied Chemistry, Glasgow (United Kingdom)

    1997-12-31

    The uptake of palladium as a conversion catalyst onto coals of different rank was investigated. Palladium fixation occurs by a different mode to that for alkaline earth and first row transition metals. Therefore, the dispersion of relatively high concentration of palladium by an ion sorption process is even possible for bituminous coals. (orig.)

  9. Surface Properties of Photo-Oxidized Bituminous Coals: Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    Natural weathering has a detrimental effect on the hydrophobic nature of coal, which in turn can influence clean-coal recovery during flotation. Few techniques are available that can establish the quality of coal surfaces and that have a short analysis time to provide input for process control. Luminescence emissions which can be quantified with an optical microscope and photometer system, are measurably influenced by degree of weathering as well as by mild storage deterioration. In addition, it has been shown that when vitrinite is irradiated with a relatively high intensity flux of violet- or ultraviolet- light in the presence of air, photo-oxidation of the surface occurs. The combination of measuring the change in luminescence emission intensity with degree of surface oxidation provided the impetus for the current investigation. The principal aim of this research was to determine whether clear correlations could be established among surface oxygen functionality, hydrophobicity induced by photo-oxidation, and measurements of luminescence intensity and alteration. If successful, the project would result in quantitative luminescence techniques based on optical microscopy that would provide a measure of the changes in surface properties as a function of oxidation and relate them to coal cleanability. Two analytical techniques were designed to achieve these goals. Polished surfaces of vitrain bands or a narrow size fraction of powdered vitrain concentrates were photo-oxidized using violet or ultraviolet light fluxes and then changes in surface properties and chemistry were measured using a variety of near-surface analytical techniques. Results from this investigation demonstrate that quantitative luminescence intensity measurements can be performed on fracture surfaces of bituminous rank coals (vitrains) and that the data obtained do reveal significant variations depending upon the level of surface oxidation. Photo-oxidation induced by violet or ultraviolet light

  10. Fire and explosion incident at bituminization demonstration facility of PNC Tokai works, on march 11, 1997

    International Nuclear Information System (INIS)

    On March 11, a fire and explosion incident occurred at the Bituminization Demonstration Facility (BDF) of Tokai Reprocessing Plant in Power Reactor and Nuclear Fuel Development Corporation (PNC). Soon after the incident, PNC (now reorganized to JNC) started to investigate the facility damage, operational records around the incident, technical notes including facility design and reviews of R and D results, operators witness and to perform several analysis, tests and calculations. This paper describes outline and cause of the incident which were concluded based on the results of continuous serious investigation, analysis and calculation. (author)

  11. Performance of PAHs emission from bituminous coal combustion

    Institute of Scientific and Technical Information of China (English)

    严建华; 尤孝方; 李晓东; 倪明江; 尹雪峰; 岑可法

    2004-01-01

    Carcinogenic and mutagenic polycyclic aromatic hydrocarbons (PAHs) generated in coal combustion have caused great environmental health concern. Seventeen PAHs (16 high priority PAHs recommended by USEPA plus Benzo[e]pyrene) present in five raw bituminous coals and released during bituminous coal combustion were studied. The effects of combustion temperature, gas atmosphere, and chlorine content of raw coal on PAHs formation were investigated. Two additives (copper and cupric oxide) were added when the coal was burned. The results indicated that significant quantities of PAHs were produced from incomplete combustion of coal pyrolysis products at high temperature, and that temperature is an important causative factor of PAHs formation. PAHs concentrations decrease with the increase of chlorine content in oxygen or in nitrogen atmosphere. Copper and cupric oxide additives can promote PAHs formation (especially the multi-ring PAHs) during coal combustion.

  12. Amenability of Muzret bituminous coal to oil agglomeration

    Energy Technology Data Exchange (ETDEWEB)

    Sahinoglu, E.; Uslu, T. [Karadeniz Technical University, Department of Mining Engineering, 61080 Trabzon (Turkey)

    2008-12-15

    Laboratory scale agglomeration tests were undertaken to investigate the amenability of Muzret (Yusufeli-Artvin) bituminous coal to oil agglomeration. Kerosene was extensively used as oil in the tests. In addition, fuel oil, diesel oil, and hazelnut oil were also used in order to determine the effect of oil type. The effects of the parameters including coal content, kerosene content, agglomeration time, coal particle size, pH, oil type, and agitation rate, on the combustible matter recovery, ash reduction and pyritic sulphur reduction, were investigated. It was found that Muzret bituminous coal could be readily cleaned by oil agglomeration with substantial reductions in ash and pyritic sulphur content. Maximum combustible matter recovery, ash reduction and pyritic sulphur reduction were achieved to be 85.54%, 59.98%, and 85.17%, respectively. (author)

  13. Identification of aggregates for Tennessee bituminous surface courses

    Science.gov (United States)

    Sauter, Heather Jean

    Tennessee road construction is a major venue for federal and state spending. Tax dollars each year go to the maintenance and construction of roads. One aspect of highway construction that affects the public is the safety of its state roads. There are many factors that affect the safety of a given road. One factor that was focused on in this research was the polish resistance capabilities of aggregates. Several pre-evaluation methods have been used in the laboratory to predict what will happen in a field situation. A new pre-evaluation method was invented that utilized AASHTO T 304 procedure upscaled to accommodate surface bituminous aggregates. This new method, called the Tennessee Terminal Textural Condition Method (T3CM), was approved by Tennessee Department of Transportation to be used as a pre-evaluation method on bituminous surface courses. It was proven to be operator insensitive, repeatable, and an accurate indication of particle shape and texture. Further research was needed to correlate pre-evaluation methods to the current field method, ASTM E 274-85 Locked Wheel Skid Trailer. In this research, twenty-five in-place bituminous projects and eight source evaluations were investigated. The information gathered would further validate the T3CM and find the pre-evaluation method that best predicted the field method. In addition, new sources of aggregates for bituminous surface courses were revealed. The results of this research have shown T3CM to be highly repeatable with an overall coefficient of variation of 0.26% for an eight sample repeatability test. It was the best correlated pre-evaluation method with the locked wheel skid trailer method giving an R2 value of 0.3946 and a Pearson coefficient of 0.710. Being able to predict field performance of aggregates prior to construction is a powerful tool capable of saving time, money, labor, and possibly lives.

  14. Study on the cause of the fire and explosion incident at Bituminization Demonstration Facility of PNC Tokai Works

    International Nuclear Information System (INIS)

    On March 11, 1997, a fire and explosion incident occurred in Bituminization Demonstration Facility (BDF) at Tokai Reprocessing Plant (TRP). The cause of the incident was thoroughly investigated and after thirty meetings of 'Investigation Committee of Science and Technology Agency (STA)'. STA reported possible cause of this incident. Continually detailed investigation was discussed at 'Follow-up Committee of STA'. Based on the results of five meetings, JNC concluded that the main cause of fire was frictional heating and viscous heating in the extruder, which provided an unusually high temperature in the bituminized product at filling, since there was no chemical analysis data suggesting the generation of chemical heat. It is considered that these excessive heat generations were due to the decreased feed rate of liquid waste to the extruder. The Follow-up Committee almost agreed to this conclusion. This paper describes general information concerning the incident and details of the cause of the incident. (author)

  15. Sorption of aqueous phosphorus onto bituminous and lignitous coal ashes

    International Nuclear Information System (INIS)

    Aiming at the development of a phosphorus removal technology for waste water, phosphate (PO43-) retention behavior of bituminous and lignitous coal ashes was investigated using a batch reactor. Ash samples, including fresh and weathered fly and bottom ashes, were studied for their sorption isotherms and reversibility. Fly ashes had a much higher phosphate retention capacity (4000-30,000 mg P/kg) than bottom ashes (15-600 mg P/kg). Lignitous coal ashes were more capable of retaining phosphate than bituminous coal ashes. The retention process was largely irreversible, and the irreversibility increased with the increase in the retention capacity. Weathering enlarged the retention capacity of the bituminous bottom ash, but substantially lowered that of the fly ash, likely due to the difference in the weather-induced changes between the fly and bottom ashes. Sorption isotherms of fly ashes were found to be adequately represented by the Langmuir model while those of bottom ashes fitted better to the Freundlich model. Concentrations of Ca2+ and PO43- in the aqueous phase were measured at the end of sorption and desorption experiments, and were compared with solubilities of three calcium phosphate minerals. The aqueous solutions were saturated or super-saturated with respect to tricalcium phosphate (Ca3(PO4)2) and hydroxyapatite (Ca5(PO4)3OH), and slightly under-saturated with respect to amorphous calcium phosphate. It is concluded that precipitation of calcium phosphate is the predominant mechanism for phosphate retention by coal ash under the conditions studied. There is a strong and positive correlation between alkalinity and phosphate sorption capacity. Consequently, acid neutralization capacity (ANC) can be used as an indicator of phosphate sorption capacity of coal ashes

  16. Sorption of aqueous phosphorus onto bituminous and lignitous coal ashes

    Energy Technology Data Exchange (ETDEWEB)

    Yan Jinying; Kirk, Donald W. [Department of Chemical Engineering and Applied Chemistry, University of Toronto, 200 College Street, Toronto, Ontario, M5S 3E5 (Canada); Jia, Charles Q. [Department of Chemical Engineering and Applied Chemistry, University of Toronto, 200 College Street, Toronto, Ontario, M5S 3E5 (Canada)], E-mail: cqjia@chem-eng.toronto.edu; Liu Xinan [College of Chemical Engineering, Chongqing University, Chongqing (China)

    2007-09-05

    Aiming at the development of a phosphorus removal technology for waste water, phosphate (PO{sub 4}{sup 3-}) retention behavior of bituminous and lignitous coal ashes was investigated using a batch reactor. Ash samples, including fresh and weathered fly and bottom ashes, were studied for their sorption isotherms and reversibility. Fly ashes had a much higher phosphate retention capacity (4000-30,000 mg P/kg) than bottom ashes (15-600 mg P/kg). Lignitous coal ashes were more capable of retaining phosphate than bituminous coal ashes. The retention process was largely irreversible, and the irreversibility increased with the increase in the retention capacity. Weathering enlarged the retention capacity of the bituminous bottom ash, but substantially lowered that of the fly ash, likely due to the difference in the weather-induced changes between the fly and bottom ashes. Sorption isotherms of fly ashes were found to be adequately represented by the Langmuir model while those of bottom ashes fitted better to the Freundlich model. Concentrations of Ca{sup 2+} and PO{sub 4}{sup 3-} in the aqueous phase were measured at the end of sorption and desorption experiments, and were compared with solubilities of three calcium phosphate minerals. The aqueous solutions were saturated or super-saturated with respect to tricalcium phosphate (Ca{sub 3}(PO{sub 4}){sub 2}) and hydroxyapatite (Ca{sub 5}(PO{sub 4}){sub 3}OH), and slightly under-saturated with respect to amorphous calcium phosphate. It is concluded that precipitation of calcium phosphate is the predominant mechanism for phosphate retention by coal ash under the conditions studied. There is a strong and positive correlation between alkalinity and phosphate sorption capacity. Consequently, acid neutralization capacity (ANC) can be used as an indicator of phosphate sorption capacity of coal ashes.

  17. Low-level radioactive wastes bituminization - ion exchange resins

    International Nuclear Information System (INIS)

    The present work describes the research and development of low level radioactive waste treatment by bituminization process in Nuclear Technology Development Centre (CDTN). Low level radioactive solid waste was simulated by mixed ion exchange resin. Cation exchange and anion resin were loaded with lithium and boric acid respectively and were incorporated in bitumen of suitable rheological properties. The simulated solid wastes incorporated in bitumen were 30 to 46 weight %. The rheological properties of waste product bitumen-mixed resin have been reported. The waste product with bitumen V-65 showed best physical and rheological properties and grave lowest leaching rates of boron and lithium. (author)

  18. Retardation of the spontaneous ignition of bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Dong, X.; Drysdale, D. [University of Edinburgh, Edinburgh (United Kingdom). Department of Civil Engineering and Building Science

    1995-12-31

    The effect of five retardants on a bituminous coal has been investigated in a temperature-controlled oven. The activation energy of oxidation in the coal inhibited by one of the retardants increases by up to 20kJ/mol, in comparison to that of the coal wetted with water. The factors affecting inhibition are considered. A kinetic interpretation of the retardation mechanism is proposed, and the possibility of using the most effective retarder in practice is discussed. 12 refs., 1 fig., 2 tabs.

  19. Behaviour of bituminized ion-exchangers under repository conditions

    International Nuclear Information System (INIS)

    This is a final report containing all the research activities and results from the period 13 July 1997-28 February 2001. The purpose of the research was to study the ageing behaviour of bituminized ion-exchanger product under simulated repository conditions. The chosen temperature in this study was 5-8 deg. C and the equilibration solution used was artificial concrete water to simulate the conditions in the final disposal. The aim was to study the properties of wetted product as a release barrier for such important waste nuclides as Sr-90 and Cs-137, which are normal constituents of the bituminized ion-exchangers. All the nine exchanged waters were analysed by ion chromatography (IC) including the follow-up of the water absorption of the samples. All the samples, which were picked up for microscopic examination, have also been analysed. A saturation-elution test was performed with one diffusion sample using tritium (H-3) as a tracer. The results have been presented and further modelling will be performed later. Further two diffusion samples were tested using H-3, Na-22 and Cl-36 as radioactive tracers. The equilibration solution was artificial concrete ground water spiked with H-3 and Na-22 and in the other case with H-3 and Cl-36. Tritium was an internal reference when comparing the results of the equilibration behaviour of Na-22 and Cl-36. From the radioactive input cells samples were taken as a function of time to monitor the equilibration process. Elution of the samples and modelling of the results will be performed later. Na-22 and Cl-36 were chosen to demonstrate the behaviour of a simple anion and cation. Diffusion tests with important waste nuclides Sr-90 and Cs-137 have been scheduled to years 2001-2002. The aim of the performed research project was to study the barrier properties of the bituminized product. The measured parameters and modelling of the results will reflect the behaviour of the wetted product as a part of the multibarrier system providing

  20. Kinetics and equilibrium modeling of uranium(VI) sorption by bituminous shale from aqueous solution

    International Nuclear Information System (INIS)

    Highlights: • Oil shales are sedimentary rocks containing a polymeric matter in a mineral matrix. • Sorption potential of bituminous shale (BS) for uranium recovery was investigated. • U(VI) sorption increased with decreasing pH and increasing temperature. • Kinetic data were analyzed based on single and two resistance diffusion models. • The results fit well to the McKay equation assuming film and intraparticle diffusion. - Abstract: Sorption of U(VI) onto a bituminous shale (BS) from a nuclear power plant project site in Black Sea region was investigated for potential risk assessment when it releases into the environment with contaminated ground and surface water. The sorption characteristics of the BS for U(VI) recovery were evaluated as a function of contact time, adsorbent dosage, initial concentration, pH and temperature. Kinetic results fit better with pseudo-second-order model rather than pseudo-first-order. The possibility of diffusion process was analyzed based on Weber–Morris intra-particle diffusion model. The McKay equation assuming film- and intraparticle diffusion better predicted the data than the Vermeulen approximation presuming surface diffusion. Equilibrium sorption data were modeled according to the Langmuir, Dubinin–Radushkevich (D–R) and Freundlich isotherm equations. Sorption capacity increased from 0.10 to 0.15 mmol g−1 in 298–318 K temperature range. FT-IR analysis and pH dependent sorption studies conducted in hydroxide and carbonate media revealed that U(VI) species were sorbed in uranyl and its hydroxo forms on the BS. Desorption studies showed that U(VI) leaching with Black Sea water was negligible from the loaded BS. The activation parameters (Ea, ΔH∗ and ΔG∗) estimated from diffusion coefficients indicated the presence of an energy barrier in the sorption system. However, thermodynamic functions derived from sorption equilibrium constants showed that overall sorption process was spontaneous in nature and

  1. Environmental problems caused by bituminous schist and possible solutions

    International Nuclear Information System (INIS)

    Schist, as a disposal of mine, has harmful effects on environment. however, several manners can be utilized to prevent the environmental destruction as well as an economical benefit is gained. In this study, environmental problems caused by bituminous schist and other disposals have been investigated on a specific lignite coal mine where schist is disposed as waste material. Pollution and damage on land and in water sources around the coal district and the villages have been observed, recorded and several solutions to environmental problems have been proposed. Discussed proposals will not only solve the environmental pollution problem but also provide waste management facility. Industrial structure of the district enables such a disposal to be used as an economical raw material. Besides, general effects of the coal mine and the power plant nearby have been discussed from environmental point of view, too. 7 refs

  2. Study of thermal reactivity during bituminization of radioactive waste

    International Nuclear Information System (INIS)

    This work deals with the study of chemical reactions and phases transitions which can occur between magnesium nitrate, sodium nitrate, cobalt sulphur product, and nickel potassium ferrocyanide, when they are heated together during bituminization process of nuclear waste. The applied methodology associates a few techniques: temperature, enthalpy, and kinetics of reaction are determined by calorimetry, reaction products are characterised by chemical analyses, mass spectrometry and XRD analysis. Three fields of temperature and energy are observed in function of composition (one compound or a mixture of compounds). The study of reactions between NaNO3 and cobalt sulphur product shows that the presence of water has got an effect on reaction temperature. The study of Mg(NO3)2, 6 H2O and CoS shows an overlapping of different signals, and that the reaction rate is very slow (a few hours). (author)

  3. DEVELOPMENT OF TEST PROTOCOLS FOR THE ANALYSIS OF MAGNETO-RHEOLOGICAL PROPERTIES OF FIELD-RESPONSIVE BITUMINOUS BINDERS

    Directory of Open Access Journals (Sweden)

    Ezio Santagata

    2014-01-01

    Full Text Available Magneto-rheological fluids are materials that exhibit a significant change in their rheological properties in the presence of a magnetic field. Because of such a field-dependent behavior, they can act as smart materials in applications in which changeable performances are desired. In road pavement engineering, the use of bitumen-based magneto-rheological fluids may open innovative scenarios related to the construction of smart pavement sections and to the investigation of damage mechanisms in binders and mixtures. The research work presented in this study explored magneto-rheological properties of several field-responsive bituminous binders obtained from two different base bitumens combined with multi-wall carbon nanotubes and powder iron. The experimental program included oscillatory shear loading tests at different temperatures, performed in the strain controlled mode by means of a dynamic shear rheometer equipped with a magneto-rheological device. The investigation was carried out with the specific goal of identifying critical issues which should be taken into account in materials preparation, testing procedures and data analysis. Undesired overheating of specimens during testing was identified and taken into account for a correct interpretation of experimental data. Thus, while the field-sensitivity of carbon nanotubes was found to be negligible as a result of the magnetic shielding action of bitumen, it was shown that powder iron can significantly affect the magneto-rheological properties of bituminous binders when employed in sufficiently high amounts. Moreover, obtained results indicated that selection of base bitumen is a key factor in designing bituminous-based smart materials. Practical implications which derive from the study are mainly relative to the fine-tuning of laboratory characterization procedures which should necessarily overcome current limitations in temperature regulation and magnetic field generation. Experimental data

  4. State of the art report on bituminized waste forms of radioactive wastes

    International Nuclear Information System (INIS)

    In this report, research and development results on the bituminization of radioactive wastes are closely reviewed, especially those regarding waste treatment technologies, waste solidifying procedures and the characteristics of asphalt and solidified forms. A new concept of the bituminization method is suggested in this report which can improve the characteristics of solidified forms. Stable solid forms with high leach resistance, high thermal resistance and good compression strength were produced by the suggested bituminization method, in which spent polyethylene from agricultural farms was added. This report can help further research and development of improved bituminized forms of radioactive wastes that will maintain long term stabilities in disposal sites. (author). 59 refs., 19 tabs., 18 figs

  5. Effect of Cement on Properties of Over-Burnt Brick Bituminous Concrete Mixes

    Science.gov (United States)

    Sarkar, Dipankar; Pal, Manish

    2016-06-01

    The present investigation is carried out to propose the use of cement coated over burnt brick aggregate in the preparation of bituminous concrete mix. The effect of cement on various mechanical properties such as Marshall stability, flow, Marshall quotient (stability to flow ratio), indirect tensile strength, stripping, rutting and fatigue life of bituminous concrete overlay has been evaluated. In this study, different cement percentages such as 2, 3, 4 and 5 % by weight of aggregate have been mixed with Over Burnt Brick Aggregate (OBBA). The laboratory results indicate that bituminous concrete prepared by 4 % cement coated OBBA gives the highest Marshall stability. The bituminous concrete mix with 4 % cement shows considerable improvement in various mechanical properties of the mix compared to the plain OBBA concrete mix.

  6. State of the art report on bituminized waste forms of radioactive wastes

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Tae Kook; Shon, Jong Sik; Kim, Kil Jeong; Lee, Kang Moo; Jung, In Ha

    1998-03-01

    In this report, research and development results on the bituminization of radioactive wastes are closely reviewed, especially those regarding waste treatment technologies, waste solidifying procedures and the characteristics of asphalt and solidified forms. A new concept of the bituminization method is suggested in this report which can improve the characteristics of solidified forms. Stable solid forms with high leach resistance, high thermal resistance and good compression strength were produced by the suggested bituminization method, in which spent polyethylene from agricultural farms was added. This report can help further research and development of improved bituminized forms of radioactive wastes that will maintain long term stabilities in disposal sites. (author). 59 refs., 19 tabs., 18 figs

  7. Synthesis document on the long time behavior of packages: operational document ''bituminous'' 2204

    International Nuclear Information System (INIS)

    This document is realized in the framework of the law of 1991 on the radioactive wastes management. The 2004 synthesis document on long time behavior of bituminous sludges packages is constituted by two documents, the reference document and the operational document. This paper presents the operational model describing the water alteration of the packages and the associated radioelements release, as the gas term source and the swelling associated to the self-irradiation and the bituminous radiolysis. (A.L.B.)

  8. A process for the bituminization of radioactive wastes

    International Nuclear Information System (INIS)

    A process is described for the incorporation of sodium nitrate solutions in bitumen, with a view to the bituminization of radioactive wastes. This process has involved the development of a chemical process and its technological application. A double jacket reactor equipped with an anchor-type stirrer has been built. Sodium nitrate (NaNO3) solutions with sodium hydroxide (NaOH) are fed into the reactor simultaneously with a bitumen emulsion while heated oil is circulated through the double jacket. After all the water has evaporated, the mixture is ''simmered'' at 170/180 deg C for up to 5 hours in order to get a homogeneous product which will be suitable for final storage. The product contains small salt crystals (10/50 μm) and has high viscosity (200/2000 poise at 160 deg C and 12 rpm), so that the possibility of sedimentation is eliminated. In comparative experiments with molten bitumen, large salt aggregates, inhomogeneously distributed, make the product unsuitable. It has been found that NaOH is responsible for the polimerization of the bitumen, which raises its viscosity. The degree of polimerization depends on the NaOH concentration and ''simmering'' time and temperature. NaOH is added to NaNO3 in order to raise the mixture's viscosity and thereby prevent sedimentation

  9. The hydrogasification of lignite and sub-bituminous coals

    Science.gov (United States)

    Bhatt, B.; Fallon, P. T.; Steinberg, M.

    1981-02-01

    A North Dakota lignite and a New Mexico sub-bituminous coal have been hydrogenated at up to 900°C and 2500 psi hydrogen pressure. Yields of gaseous hydrocarbons and aromatic liquids have been studied as a function of temperature, pressure, residence time, feed rates and H2/coal ratio. Coal feed rates in excess of 10 lb/hr have been achieved in the 1 in. I. D.×8 ft reactor and methane concentration as high as 55% have been observed. A four-step reaction model was developed for the production and decomposition of the hydrocarbon products. A single object function formulated from the weighted errors for the four dependent process, variables, CH4, C2H6, BTX, and oil yields, was minimized using a program containing three independent iterative techniques. The results of the nonlinear regression analysis for lignite show that a first-order chemical reaction model with respect to C conversion satisfactorily describes the dilute phase hydrogenation. The activation energy for the initial products formation was estimated to be 42,700 cal/gmole and the power of hydrogen partial pressure was found to be +0.14. The overall correlation coefficient was 0.83. The mechanism, the rate expressions, and the design curves developed can be used for scale-up and reactor design.

  10. Gasification of high ash, high ash fusion temperature bituminous coals

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

    2015-11-13

    This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

  11. Effect of transesterification degree and post-treatment on the in-service performance of NCO-functionalized vegetable oil bituminous products

    OpenAIRE

    Cuadri Vega, Antonio Abad; García Morales, Moisés; Navarro Domínguez, Francisco Javier; Partal López, Pedro

    2014-01-01

    The bitumen modification through polyurethane prepolymers presents significant benefits for the manufacture of bituminous products for the paving industry. In this sense, this work explores the use, as bitumen modifier, of a novel reactive prepolymer synthesized by reaction of 4,4´,diphenylmethane diisocyanate (MDI) and a vegetable oil-based polyol, castor oil (CO), previously transesterified with pentaerythritol. On the one hand, thermal analysis on transesterified CO revealed a highly stabl...

  12. Bituminous reference document: synthesis of knowledge on the long time behavior of bituminous packages; Dossier de reference bitume: synthese des connaissances sur le comportement a long terme des colis bitumes

    Energy Technology Data Exchange (ETDEWEB)

    Sercombe, J.; Adenot, F.; Vistoli, P.P.; Parraud, S.; Riglet-Martial, C.; Gwinner, B.; Felines, I.; Tiffreau, C.; Libert, M

    2004-07-01

    This document is a synthesis of the knowledge acquired at the CEA on the behavior of bituminous packages. In this framework, the CEA studied bituminous packages in generic conditions of a package lifetime. The main factors, the evolution mechanisms and influential parameters have been determined and quantitative s simulation have been developed. After a description of the main initial bituminous packages characterizations, the evolutions in saturated and un-saturated environment are exposed. (A.L.B.)

  13. Effects of salt content on leaching properties of synthetic bituminized wastes

    International Nuclear Information System (INIS)

    The leaching properties of soluble components (Na+, NO3−, and NO2−) in synthetic bituminized wastes with various characteristics, such as salt content, salt composition, and bitumen matrix, were quantitatively evaluated by means of an aqueous leaching test. Micropores were formed in the bituminized waste by the leaching of soluble salts. The penetrability of bitumen and the salt content affected the size and the shape of the micropores observed by scanning electron microscopy. The linear relationship between leaching fraction of the soluble components and square root of leaching time was observed, and the diffusion coefficient of the soluble component was determined by Fick's law. The diffusion coefficients of ionic species of interest were similar to each other. Moreover, the diffusion coefficient agreed among bituminized wastes with the same salt content, even if salt composition and bitumen matrix were different. The diffusion coefficient of the component was proportional to the salt content in the synthetic bituminized wastes. It was found that the salt content in the bituminized waste was one of the key factors to determine the diffusion coefficient. (author)

  14. Using proximate analysis to characterize airborne dust generation from bituminous coals

    Energy Technology Data Exchange (ETDEWEB)

    Page, S.J.; Organiscak, J.A.

    2005-11-01

    Prolonged exposure to airborne respirable coal dust is responsible for coal workers pneumoconiosis (CWP), commonly called black lung. Health research studies have identified that the prevalence and severity of CWP are directly related to both the amount of dust exposure and the coal rank. The amount of airborne respirable dust (ARD) smaller than 10 micrometers generated from breakage of different coals varies widely. To investigate the cause, researchers for the National Institute for Occupational Safety and Health (NIOSH) have conducted experiments to identify the causes of airborne respirable dust liberation. Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals from eight mines. The results indicate that the proximate analysis of a coal sample can provide a very good indicator of the potential for a dust problem. For application to the coal mining, processing, and utilization industries, data from 977 US coal seams compiled by the Department of Energy (DoE) has been used to calculate this dust generation potential from an equation based on the NIOSH measured data. A simple procedure for this calculation is provided. 1 fig.

  15. Safety assessment for the bituminization facility of the medium-level waste

    International Nuclear Information System (INIS)

    The safety assessment for the home-made bituminization facility of the medium-level waste during hot test is made. The average external dose equivalent per month is 0.136 x 10-2 Sv. The radioactive substance released into the environment is much lower than the permissible limit. The danger of burning and exploding of the bituminized product is avoided because the operation temperature is controlled strictly below 170 C degree. The report also briefly describes the structural characteristic of the facility, the main process and radiation protection and safety measures

  16. Project and design of apparatus and equipment of pilot plant experimental bituminization line PS 44 EBO

    International Nuclear Information System (INIS)

    The modifications are described made in the design of major components of the pilot plant experimental bituminization line involving: the mixing equipment, the film rotor evaporator, the calciner, and various transport mechanisms for handling drums and containers. The difficulty and complexity of the problem which Kralovopolska strojirna Brno, the end supplier of the bituminization line, will have to tackle is evident mainly from the case of bridge cranes, which feed the line, and the full-portal gantry crane which handles the containers and drums at regional sites of radioactive waste disposal. (Z.M.)

  17. Installation in the A-1 plant of an experimental bituminization line by VUCHZ

    International Nuclear Information System (INIS)

    Following the termination of the experimental operation of the bituminization line at the Research Institute for Chemical Installations in Brno, the line was dismantled and transferred to the nucler power plant in Jaslovske Bohunice. The installation of the line, the layout of the assemblies are described and the results of tests with non-radioactive simulated wastes and actual radioactive wastes briefly described. An amount of 3.2 m3 of actual radioactive wastes from the V-1 nuclear power plant was processed in the tests. The results confirmed the suitability of bituminization for processing liquid radioactive wastes from WWER nuclear power plants. (Z.M.)

  18. 8th RILEM International Symposium on Testing and Characterization of Sustainable and Innovative Bituminous Materials

    CERN Document Server

    Partl, Manfred

    2016-01-01

    This work presents the results of RILEM TC 237-SIB (Testing and characterization of sustainable innovative bituminous materials and systems). The papers have been selected for publication after a rigorous peer review process and will be an invaluable source to outline and clarify the main directions of present and future research and standardization for bituminous materials and pavements. The following topics are covered: - Characterization of binder-aggregate interaction - Innovative testing of bituminous binders, additives and modifiers - Durability and aging of asphalt pavements - Mixture design and compaction analysis - Environmentally sustainable materials and technologies - Advances in laboratory characterization of bituminous materials - Modeling of road materials and pavement performance prediction - Field measurement and in-situ characterization - Innovative materials for reinforcement and interlayer systems - Cracking and damage characterization of asphalt pavements - Rec...

  19. Noise Reduction Properties of an Experimental Bituminous Slurry with Crumb Rubber Incorporated by the Dry Process

    Directory of Open Access Journals (Sweden)

    Moisés Bueno

    2014-08-01

    Full Text Available Nowadays, cold technology for asphalt pavement in the field of road construction is considered as an alternative solution to conventional procedures from both an economic and environmental point of view. Among these techniques, bituminous slurry surfacing is obtaining an important role due to the properties of the obtained wearing course. The functional performance of this type of surfaces is directly related to its rough texture. Nevertheless, this parameter has a significant influence on the tire/road noise generation. To reduce this undesirable effect on the sound performance, new designs of elastic bituminous slurries have been developed. Within the FENIX project, this work presents the acoustical characterization of an experimental bituminous slurry with crumb rubber from wasted automobile tires incorporated by the dry process. The obtained results show that, under controlled operational parameters, the close proximity sound levels associated to the experimental slurry are considerably lower than those emitted by a conventional slurry wearing course. However, after one year of supporting traffic loads and different weather conditions, the evaluated bituminous slurry, although it conserves the original noise reduction properties in relation to the conventional one, noticeably increases the generated sound emission. Therefore, it is required to continue improving the design of experimental surfaces in order to enhance its long-term performance.

  20. Development and operation experience from pilot-plant for bituminization of liquid radioactive wastes (UBD-200)

    International Nuclear Information System (INIS)

    The results are given for investigations of liquid radioactive wastes bituminization on the pilot-plant of continious operation. The bituminization process is divided into two stages. On the first stage salts with definite moisture content are obtained. On the second stage, wet salts are mixed with melted bitumen. In this process the salts are finally dryed and bitumen compound produced is transported towards the discharge assembly. Design of the dryer and mixer is described and their technical parameters are given. Salt-bitumen compound is discharged in moulding bogies with volume of 0.5 m3. After hardening, salt-bitumen compound blocks are removed for burial. Average composition of liquid radioactive wastes coming for solidification is given. Dependences of the salt-bitumen compound characteristics on the parameters of the technological process of bituminization are given as well as the results of analysis of filling of compound by salts at the block height of 0.3 m. It is shown that division of the bituminization process into two stages do not affect on the chemical stability of compound. (I.T.)

  1. Towards an Accurate Stress Dependant Time & Frequency Domain VE Response Model for Bituminous Binders

    NARCIS (Netherlands)

    Woldekidan, M.F.; Huurman, M.; Pronk, A.C.

    2010-01-01

    Linear viscoelastic properties of bituminous binders for short loading times are analyzed using dynamic mechanical analysis methods. Dynamic Shear Rheometer (DSR) test with parallel plate (PP) configuration is widely used for this purpose. Due to the complex stress distribution over the cross-sectio

  2. Bituminization system of low level liquid waste in Genkai Nuclear Power Plant

    International Nuclear Information System (INIS)

    The bituminization system for low level radioactive liquid wastes has such advantages as its volume reduction is 6 to 10 times higher than the cementing systems, and the exuding ratio of radioactive nuclides from bituminized body into sea water is smaller, because the solids containing radioactive nuclides are solidified into oily bitumen which is very water repellent. Therefore, Genkai No.2 reactor plant has adopted the batch bituminization system, the main equipment of which being a drum mixer. This equipment has the capacity of treating 35 m3 of drain from the machines (boron 21,000 ppm) yearly, mainly composed of boric acid, and 85 m3 of floor drain/laundry drain yearly (solids 1.1 wt.%). This paper describes the outline of the system, the improvement of the installation, operating method, operation control, and the results of cold and hot operations. At the beginning of the trial operation, the concentrated laundry drain from No.1 reactor during the regular inspection was bituminized, and the concentrated sodium borate solution from No.2 reactor was treated since July, 1980. These results show the good volume reduction, condensate-processing capability, mixer controllability and mixer decontamination efficiency. (Wakatsuki, Y.)

  3. Effect of bituminous coal properties on carbon dioxide and methane high pressure sorption

    Czech Academy of Sciences Publication Activity Database

    Weishauptová, Zuzana; Přibyl, Oldřich; Sýkorová, Ivana; Machovič, Vladimír

    2015-01-01

    Roč. 139, JAN 1 (2015), s. 115-124. ISSN 0016-2361 Institutional support: RVO:67985891 Keywords : bituminous coal * sorption capacity * maceral composition * Upper Silesian Coal Basin Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.520, year: 2014

  4. Development of new non destructive methods for bituminized radioactive waste drums characterization

    International Nuclear Information System (INIS)

    Radioactive waste constitute a major issue for the nuclear industry. One of the key points is their characterization to optimize their management: treatment and packaging, orientation towards the suited disposal. This thesis proposes an evaluation method of the low-energy photon attenuation, based on the gamma-ray spectra Compton continuum. Effectively, the 241Am measurement by gamma-ray spectrometry is difficult due to the low energy of its main gamma-ray (59.5 keV). The photon attenuation strongly depends on the bituminous mix composition, which includes very absorbing elements. As the Compton continuum also depends on this absorption, it is possible to link the 59.5 keV line attenuation to the Compton level. Another technique is proposed to characterize uranium thanks to its fluorescence X-rays induced by the gamma emitters already present in the waste. The uranium present in the drums disturbs the neutron measurements and its measurement by self-induced X-ray fluorescence allows to correct this interference. Due to various causes of error, the total uncertainty is around 50 % on the activity of the radioisotope 241Am, corrected by the peak to Compton technique. The same uncertainty is announced on the uranium mass measured by self induced X-ray fluorescence. As a consequence of these promising results, the two methods were included in the industrial project of the 'Marcoule Sorting Unit'. One major advantage is that they do not imply any additional material because they use information already present in the gamma-ray spectra. (author)

  5. Testing of the possibility for the use of BEWAG-coal cinder in bituminous supporting layers of asphalt fastening

    Energy Technology Data Exchange (ETDEWEB)

    Ueckert, H.W.

    1981-01-01

    In order to develop further use of coal cinder granulate the suitability of that granulate has been tested for use as an additional material for bituminous supporting layers. Results: (1) The granulate can be used for asphalt supporting layers Type B according TVT 72. (2) The granulation scope 0/5 mm is recommended. (3) The granular share of the mineral mixture can amount up to 30% of weight. (4) Standard-Bitumen B 65 can be used as bituminous binders. (5) The optimum consistence of the bituminous materials has to be found according of an aptitude test.

  6. Sorbent Injection for Small ESP Mercury Control in Low Sulfur Eastern Bituminous Coal Flue Gas

    Energy Technology Data Exchange (ETDEWEB)

    Carl Richardson; Katherine Dombrowski; Douglas Orr

    2006-12-31

    This project Final Report is submitted to the U.S. Department of Energy (DOE) as part of Cooperative Agreement DE-FC26-03NT41987, 'Sorbent Injection for Small ESP Mercury Control in Low Sulfur Eastern Bituminous Coal Flue Gas.' Sorbent injection technology is targeted as the primary mercury control process on plants burning low/medium sulfur bituminous coals equipped with ESP and ESP/FGD systems. About 70% of the ESPs used in the utility industry have SCAs less than 300 ft2/1000 acfm. Prior to this test program, previous sorbent injection tests had focused on large-SCA ESPs. This DOE-NETL program was designed to generate data to evaluate the performance and economic feasibility of sorbent injection for mercury control at power plants that fire bituminous coal and are configured with small-sized electrostatic precipitators and/or an ESP-flue gas desulfurization (FGD) configuration. EPRI and Southern Company were co-funders for the test program. Southern Company and Reliant Energy provided host sites for testing and technical input to the project. URS Group was the prime contractor to NETL. ADA-ES and Apogee Scientific Inc. were sub-contractors to URS and was responsible for all aspects of the sorbent injection systems design, installation and operation at the different host sites. Full-scale sorbent injection for mercury control was evaluated at three sites: Georgia Power's Plant Yates Units 1 and 2 [Georgia Power is a subsidiary of the Southern Company] and Reliant Energy's Shawville Unit 3. Georgia Power's Plant Yates Unit 1 has an existing small-SCA cold-side ESP followed by a Chiyoda CT-121 wet scrubber. Yates Unit 2 is also equipped with a small-SCA ESP and a dual flue gas conditioning system. Unit 2 has no SO2 control system. Shawville Unit 3 is equipped with two small-SCA cold-side ESPs operated in series. All ESP systems tested in this program had SCAs less than 250 ft2/1000 acfm. Short-term parametric tests were conducted on Yates

  7. Transformism in Alberta: The Environmental Political Economy of the Bituminous Sands

    Science.gov (United States)

    Katz-Rosene, Ryan

    This thesis attempts to help establish environmental political economy as a viable academic field while providing an example of work in the discipline. It offers an analysis of societal processes resulting in the co-optation and/or neutralization of critical environmentalist ideas. Using Alberta's bituminous sands as a case study, and a Gramsci-influenced eco-Marxist theory as a foundation, the thesis argues that the term 'environmental transformism' (inspired by the Gramscian term trasformismo) is helpful in describing and framing such processes. Accordingly, the ensuing chapters provide an analysis of why environmental transformism is happening in Alberta, and demonstrate how this mechanism works at protecting the status quo from threatening ideologies, thereby consolidating neoliberal capitalism. A concluding argument discusses the inherent dangers posed to society by the transformism of certain environmental subjectivities. The thesis begins by introducing the contentious social and environmental issues surrounding the development of the bituminous sands.

  8. Radiation-chemical transformation of synthetic oil from oil-bituminous rock

    International Nuclear Information System (INIS)

    Full text : Like as test subject was used synthetic oil from oil-bituminous rocks of Balakhany deposit. The regularities of synthetic oils radiation-chemical transformations were studied. Laboratory researches were carried out in an interval of absorbed dose 43-216 kGr and dose rate 0.5 Gr/s. Concentration, radiation-chemical yields of the received gases in the various absorbed doses were established. Results of researches allow to estimate possibility use of oil products received from synthetic oil for isolation of radioactive sources from environment. The purpose of the given work is research of radiation stability of synthetic oil from bituminous rock. Results of such researches will allow to estimate possibility of production different purpose oil products from synthetic oil in a radiation-chemical way and also use of these materials for isolation of radioactive sources from environment

  9. A Method to Estimate the Dynamic Displacement and Stress of a Multi-layered Pavement with Bituminous or Concrete Materials

    OpenAIRE

    LU, ZHENG; Yao, Hailin; Zhang, JingBo

    2014-01-01

    In this research work, a method to estimate the dynamic characteristics of a multilayered pavement with bituminous or concrete materials is proposed. A mechanical model is established to investigate the dynamic displacement and stress of the multi-layered pavement structure. Both the flexible and the rigid pavements, corresponding to bituminous materials and concrete materials, respectively, are studied. The theoretical solutions of the multi-layered pavement structure are deduced considering...

  10. Is Atomic Force Microscopy suited as Tool for fast Screening of Bituminous Materials? An Inter-laboratory Comparison Study

    OpenAIRE

    Nahar, S.N.; Dillingh, B.; Erkens, S.M.J.G.; Schmets, A. J. M.; Fischer, H.R.; Scarpas, A.; Schitter, G.

    2013-01-01

    Bituminous binders are known to have microstructures at typical length scales of micrometers. This microstructure can be probed with Atomic Force Microscopy (AFM). Now that worldwide several research groups are reporting AFM results on bitumen, it is becoming important to improve the understanding of the reproducibility and objectivity of the technique for studying bituminous samples. When reproducibility and stability are proven, AFM can be a tool for asphalt professionals to rapidly screen ...

  11. Modelling the quasi-static behaviour of bituminous material using a cohesive zone model

    OpenAIRE

    Tabakovic, Amir; Karac, Aleksandar; Ivankovic, Alojz; Gibney, Amanda; McNally, Ciaran; Gilchrist, M. D.

    2010-01-01

    This paper investigates the applicability of a cohesive zone model for simulating the performance of bituminous material subjected to quasistatic loading. The Dugdale traction law was implemented within a finite volume code in order to simulate the binder course mortar material response when subjected to indirect tensile loading. A uniaxial tensile test and a threepoint bend test were employed to determine initial stress-strain curves at different test rates and the cohesive zone parameters (...

  12. Slagging behavior of upgraded brown coal and bituminous coal in 145 MW practical coal combustion boiler

    Energy Technology Data Exchange (ETDEWEB)

    Akiyama, Katsuya; Pak, Haeyang; Takubo, Yoji [Kobe Steel, Ltd, Kobe (Japan). Mechanical Engineering Research Lab.; Tada, Toshiya [Kobe Steel, Ltd, Takasago (Japan). Coal and Energy Technology Dept.; Ueki, Yasuaki [Nagoya Univ. (Japan). Energy Science Div.; Yoshiie, Ryo; Naruse, Ichiro [Nagoya Univ. (Japan). Dept. of Mechanical Science and Engineering

    2013-07-01

    The purpose of this study is to quantitatively evaluate behaviors of ash deposition during combustion of Upgraded Brown Coal (UBC) and bituminous coal in a 145 MW practical coal combustion boiler. A blended coal consisting 20 wt% of the UBC and 80 wt% of the bituminous coal was burned for the combustion tests. Before the actual ash deposition tests, the molten slag fractions of ash calculated by chemical equilibrium calculations under the combustion condition was adopted as one of the indices to estimate the tendency of ash deposition. The calculation results showed that the molten slag fraction for UBC ash reached approximately 90% at 1,523 K. However, that for the blended coal ash became about 50%. These calculation results mean that blending the UBC with a bituminous coal played a role in decreasing the molten slag fraction. Next, the ash deposition tests were conducted, using a practical pulverized coal combustion boiler. A water-cooled stainless-steel tube was inserted in locations at 1,523 K in the boiler to measure the amount of ash deposits. The results showed that the mass of deposited ash for the blended coal increased and shape of the deposited ash particles on the tube became large and spherical. This is because the molten slag fraction in ash for the blended coal at 1,523 K increased and the surface of deposited ash became sticky. However, the mass of the deposited ash for the blended coal did not greatly increase and no slagging problems occurred for 8 days of boiler operation under the present blending conditions. Therefore, appropriate blending of the UBC with a bituminous coal enables the UBC to be used with a low ash melting point without any ash deposition problems in a practical boiler.

  13. The microstructure of petroleum vacuum residue films for bituminous concrete: a microscopy approach.

    Science.gov (United States)

    Sourty, E D; Tamminga, A Y; Michels, M A J; Vellinga, W-P; Meijer, H E H

    2011-02-01

    Selected carbon-rich refinery residues ('binders') mixed with mineral particles can form composite materials ('bituminous concrete') with bulk mechanical properties comparable to those of cement concrete. The microstructural mechanism underlying the remarkable composite properties has been related to the appearance of a rigid percolating network consisting of asphaltenes and mineral particles [Wilbrink M. et al. (2005) Rigidity percolation in dispersions with a structured visco-elastic matrix. Phys. Rev. E71, 031402]. In this paper, we explore the microstructure of thin binder films of varying thickness with a number of microscopic characterization techniques, and attempt to relate the observed microstructure to the distinctive mechanical behaviour. Two binders, only one of which has been proven to be suitable for bituminous concrete were investigated, and their microstructure compared. Both binders show the formation of asphaltene aggregates. The binder suitable for bituminous concrete is distinguished by the fact that the asphaltenes show a stronger tendency towards such aggregation, due to a higher concentration and less stabilization in the maltene phase. They also show a clear affinity to other species (such as waxes) and may act as nucleation sites for crystals and aggregates of those species. PMID:21118207

  14. Continuous bench-scale slurry catalyst testing direct coal liquefaction rawhide sub-bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Bauman, R.F.; Coless, L.A.; Davis, S.M. [and others

    1995-12-31

    In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263. Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.

  15. JV Task 126 - Mercury Control Technologies for Electric Utilities Burning Bituminous Coal

    Energy Technology Data Exchange (ETDEWEB)

    Jason Laumb; John Kay; Michael Jones; Brandon Pavlish; Nicholas Lentz; Donald McCollor; Kevin Galbreath

    2009-03-29

    The EERC developed an applied research consortium project to test cost-effective mercury (Hg) control technologies for utilities burning bituminous coals. The project goal was to test innovative Hg control technologies that have the potential to reduce Hg emissions from bituminous coal-fired power plants by {ge}90% at costs of one-half to three-quarters of current estimates for activated carbon injection (ACI). Hg control technology evaluations were performed using the EERC's combustion test facility (CTF). The CTF was fired on pulverized bituminous coals at 550,000 Btu/hr (580 MJ/hr). The CTF was configured with the following air pollution control devices (APCDs): selective catalytic reduction (SCR) unit, electrostatic precipitator (ESP), and wet flue gas desulfurization system (WFDS). The Hg control technologies investigated as part of this project included ACI (three Norit Americas, Inc., and eleven Envergex sorbents), elemental mercury (Hg{sup 0}) oxidation catalysts (i.e., the noble metals in Hitachi Zosen, Cormetech, and Hitachi SCR catalysts), sorbent enhancement additives (SEAs) (a proprietary EERC additive, trona, and limestone), and blending with a Powder River Basin (PRB) subbituminous coal. These Hg control technologies were evaluated separately, and many were also tested in combination.

  16. Study on Plastic Coated Overburnt Brick Aggregate as an Alternative Material for Bituminous Road Construction

    Directory of Open Access Journals (Sweden)

    Dipankar Sarkar

    2016-01-01

    Full Text Available There are different places in India where natural stone aggregates are not available for constructional work. Plastic coated OBBA can solve the problem of shortage of stone aggregate to some extent. The engineers are always encouraged to use locally available materials. The present investigation is carried out to evaluate the plastic coated OBBA as an alternative material for bituminous road construction. Shredded waste plastics are mixed with OBBA in different percentages as 0.38, 0.42, 0.46, 0.50, 0.54, and 0.60 of the weight of brick aggregates. Marshall Method of mix design is carried out to find the optimum bitumen content of such bituminous concrete mix prepared by plastic coated OBBA. Bulk density, Marshall Stability, flow, Marshall Quotient, ITS, TSR, stripping, fatigue life, and deformations have been determined accordingly. Marshall Stability value of 0.54 percent of plastic mix is comparatively higher than the other mixes except 0.60 percent of plastic mix. Test results are within the prescribed limit for 0.54 percent of plastic mix. There is a significant reduction in rutting characteristics of the same plastic mix. The fatigue life of the mix is also significantly higher. Thus plastic coated OBBA is found suitable in construction of bituminous concrete road.

  17. Time dependent viscoelastic rheological response of pure, modified and synthetic bituminous binders

    Science.gov (United States)

    Airey, G. D.; Grenfell, J. R. A.; Apeagyei, A.; Subhy, A.; Lo Presti, D.

    2016-04-01

    Bitumen is a viscoelastic material that exhibits both elastic and viscous components of response and displays both a temperature and time dependent relationship between applied stresses and resultant strains. In addition, as bitumen is responsible for the viscoelastic behaviour of all bituminous materials, it plays a dominant role in defining many of the aspects of asphalt road performance, such as strength and stiffness, permanent deformation and cracking. Although conventional bituminous materials perform satisfactorily in most highway pavement applications, there are situations that require the modification of the binder to enhance the properties of existing asphalt material. The best known form of modification is by means of polymer modification, traditionally used to improve the temperature and time susceptibility of bitumen. Tyre rubber modification is another form using recycled crumb tyre rubber to alter the properties of conventional bitumen. In addition, alternative binders (synthetic polymeric binders as well as renewable, environmental-friendly bio-binders) have entered the bitumen market over the last few years due to concerns over the continued availability of bitumen from current crudes and refinery processes. This paper provides a detailed rheological assessment, under both temperature and time regimes, of a range of conventional, modified and alternative binders in terms of the materials dynamic (oscillatory) viscoelastic response. The rheological results show the improved viscoelastic properties of polymer- and rubber-modified binders in terms of increased complex shear modulus and elastic response, particularly at high temperatures and low frequencies. The synthetic binders were found to demonstrate complex rheological behaviour relative to that seen for conventional bituminous binders.

  18. The projects of reducing environmental pollution at the collieries belonging to Petrosani Autonomous Bituminous Coal Administration

    International Nuclear Information System (INIS)

    The economic development in the Jiu Valley, as practised in the mining and processing of bituminous coal, has had a dynamic character without taking into account, however, the harmful impact on the environment. The most severe problem of environmental pollution in the Jiu Valley is that of the pollution of the Jiu River due to the discharge of waste water from the technological processes of mining and processing coal. This paper presents some solutions for reducing this environmental pollution, especially the Jiu water pollution. 1 ref

  19. Investigation of activity release from bituminized intermediate-level waste forms under thermal stresses

    International Nuclear Information System (INIS)

    To determine the consequences of a fire during fabrication, intermediate storage and transport of bituminized NaNO3 waste forms, the fractions of plutonium released from the waste forms were assessed. For this purpose, laboratory tests were made with PuO2-containing specimens as well as a field test with specimens containing Eu2O3. By the evaluation of plutonium release in the laboratory and by the determination of the total sodium release and the relative Eu/Na release in the field tests the plutonium release can be deduced from full-scale specimens. The results show that for bituminized waste forms with high NaNO3 contents (approx. 36 wt%) the average plutonium release obtained in laboratory testing is 15%. In the field tests (IAEA fire test conditions) an average Eu release of 8% was found. These results justify the statement that also for waste forms in open 175 L drum inserts a maximum plutonium release of about 15% can be expected. From the time-dependence of Eu/Na release in the field tests an induction period of 15-20 minutes between the start of testing and the first Na/Eu release can be derived. The maximum differential Na/Eu release occurs after a test period of 45 to 60 minutes duration and after 90 to 105 minutes (tests K2 and K4, respectively); after that time also the highest temperatures in the products are measured. The release values were determined for products in open 175 L drum inserts which in this form are not eligible for intermediate and ultimate storage. For bituminized waste forms in concrete packages (lost concrete shieldings) a delayed increase in temperature to only 70-80 deg. C takes place (4-5 hours after extinction of the fire) if the fire lasts 45 minutes. The concrete package remains intact under test conditions. This means that activity release from bituminized waste forms packaged in this way can be ruled out in the case under consideration. (author)

  20. Bituminization of radioactive waste concentrates from reprocessing, nuclear research establishments and nuclear power plants

    International Nuclear Information System (INIS)

    This report is a summary of the major results of R and D work performed at the Karlsruhe Nuclear Research Center from 1967 until 1977 for fixing radioactive waste concentrates in bitumen and for characterizing the resulting products. Moreover, the report provides a compilation of operating experience gathered at the Karlsruhe Nuclear Research Center in bituminizing low and medium level evaporator concentrates. The report also contains the results of R and D work carried out by external institutes on behalf of the KfK. (orig.)

  1. Co-combustion of bituminous coal and biomass fuel blends: Thermochemical characterization, potential utilization and environmental advantage.

    Science.gov (United States)

    Zhou, Chuncai; Liu, Guijian; Wang, Xudong; Qi, Cuicui

    2016-10-01

    The thermochemical characteristics and gaseous trace pollutant behaviors during co-combustion medium-to-low ash bituminous coal with typical biomass residues (corn stalk and sawdust) were investigated. Lowering of ignition index, burnout temperature and activation energy in the major combustion stage are observed in the coal/biomass blends. The blending proportion of 20% and 30% are regarded as the optimum blends for corn stalk and sawdust, respectively, in according the limitations of heating value, activation energy, flame stability and base/acid ratio. The reductions of gaseous As, Cd, Cu, Pb, Zn and polycyclic aromatic hydrocarbon (PAHs) were 4.5%, 7.8%, 6.3%, 9.8%, 9.4% and 17.4%, respectively, when co-combustion coal with 20% corn stalk. The elevated capture of trace elements were found in coal/corn stalk blend, while the coal/sawdust blend has the better PAHs control potential. The reduction mechanisms of gaseous trace pollutants were attributed to the fuel property, ash composition and relative residence time during combustion. PMID:27393832

  2. Applied Technological Direction of Power Plant Ash and Slag Waste Management when Kuznetsk Bituminous Coal is Burned

    Directory of Open Access Journals (Sweden)

    Lihach Snejana A.

    2016-01-01

    Full Text Available Currently a lot of power plants have a problem with storage of coal combustion solid by-products (ash and slag. Holding capacity of existing power plants available ash dumps were enlarged and modernized repeatedly. Many plants have two or even three of them. Today new ash dump construction is economically inconvenient due to need to assign new plots of land and their inconveniently big distance from a plant, which increase ash and slag transportation expenses. The goal of our research work is to find promising directions for ash and slag waste mass utilization based on Kuznetsk bituminous coals experimental data on ultimate composition and properties. The experimental research of ash, slag and their mixture samples from ash dumps brought us to conclusion that the most promising direction for these materials application in large quantities is construction industry including road construction. Be-sides, we lined up some other directions for ash, slag, and ash and slag mixture possible application. These directions might not provide mass utilization but they are promising from a point of view of the researched waste properties.

  3. A Method to Estimate the Dynamic Displacement and Stress of a Multi-layered Pavement with Bituminous or Concrete Materials

    Directory of Open Access Journals (Sweden)

    Zheng LU

    2014-12-01

    Full Text Available In this research work, a method to estimate the dynamic characteristics of a multilayered pavement with bituminous or concrete materials is proposed. A mechanical model is established to investigate the dynamic displacement and stress of the multi-layered pavement structure. Both the flexible and the rigid pavements, corresponding to bituminous materials and concrete materials, respectively, are studied. The theoretical solutions of the multi-layered pavement structure are deduced considering the compatibility condition at the interface of the structural layers. By introducing FFT (Fast Fourier Transform algorithm, some numerical results are presented. Comparisons of the theoretical and experimental result implied that the proposed method is reasonable in predicting the stress and displacement of a multi-layered pavement with bituminous or concrete materials. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6071

  4. Low SO2 emission from CFB co-firing MSW and bituminous.

    Science.gov (United States)

    Lu, Qing-Gang; Li, Zhi-Wei; Na, Yong-Jie; Ba, Shao-Lin; Sun, Yun-Kai; He, Jun

    2004-01-01

    Influence of co-firing rate on SO2 emission from co-firing municipal solid waste (MSW) and bituminous containing high amount of sulfur (1.79%) was studied in a 0.15 MWt circulating fluidized bed (CFB). The temperature selected is 1123 K, typical for MSW incineration using CFB. The particle concentration in the dilution zone of the furnace, the alkali metal concentration and sulfate concentration in the recirculating ash and fly ash, and flue gas composition were determined. The results showed that the addition of MSW leads to a significant decrease in SO2 emission. Concentration of SO2 in flue gas decreased to 0 with the co-firing rate greater than 51%. This reduction in SO2 emission is attributed both to the high particle concentration in the dilution zone of the furnace, the high content of alkali metals in the bed material, and to the comparatively high concentration of HCI in flue gas during co-firing of MSW and bituminous. PMID:15559820

  5. THE HISTORY OF EXPLORATION AND EXPLOITATION OF BITUMINOUS AND KEROGENOUS DEPOSITS IN CROATIA

    Directory of Open Access Journals (Sweden)

    Berislav Šebečić

    1995-12-01

    Full Text Available It is assumed thal the first known sedimens of natural bitumen or asphalt in coastal Croatia were exploited as the early moddle ages. Yet authenticated written documents about Vinišće near Trogir derive from no earlier than 1628, about Vrgorac/Paklina from only 1753. By the end of the 18th century, many deposits were discovered in Dalmatia, but it was Škrip on the Island of Brač and Suhi Dolac that were important. The earliest known deposits and occurrences of kerogenous rocks, or bituminous or oil shales, are mentioned as stone or fossil coal in Sovinjak, in the upper course of the River Mirna, and in Rebići in Istria; near Sinj, Slivno not far from the River Neretva, Mirta and near Nerežišće on the Island uf Brač. All if these were well known and described in 1804, while Sovinjak was mentioned in the 16th century. In the article, some of new information derived from mining and geological research into bituminous and kerogenous sediments and deposits are provided (the paper is published in Croatian.

  6. Assessing radioactive concentrates and waste vapor condensate in solidifying radioactive wastes by bituminization

    International Nuclear Information System (INIS)

    A brief overview is presented of chemical and radiochemical methods used in the world for the analysis of the concentrate of liquid radioactive wastes from nuclear power plants destined for bituminization. Most methods are also suitable for an analysis of the condensate of waste vapors produced in bituminization. The methods of analysis of the radioactive concentrate from the V-1 nuclear power plant in Jaslovske Bohunice and of the waste vapors condensate were developed and tested in practice. Gross gamma activity was measured using a well-type Na(Tl) scintillation detector, the content of radionuclides was determined using semiconductor Ge(Li) spectrometry. The concentration of boric acid in the concentrate was determined by titration with mannite; in the condensate, using spectrophotometry with curcumine. The content of nitrates in both the concentrate and the condensate was determined spectrophotometrically using salicylic acid, the content of nitrites was determined by spectrophotometry using sulfanilic acid and α-naphthylamine. Carbonates and chlorides were determined by titration, sodium and potassium by flame photometry. The content of organic acids was measured by gravimetry of extracted methyl esters, the content of surfactants by spectrophotometry. Infrared spectrophotometry was used in determining hydrocarbons in the waste vapor condensate. The measured value range and the measurement errors are shown for each method. (A.K.)

  7. Feasibility study of producing lump fuel using oil-bituminous sands

    Energy Technology Data Exchange (ETDEWEB)

    Moldybaev, A.B.; Ermagambetov, B.T.; Mamraeva, K.M.; Shin, R.G.; Bakirova, R.K. (Institut Organicheskogo Sinteza i Uglekhimii AN KazSSR (USSR))

    1991-04-01

    Describes production of lump fuel by briquetting and coking different mixtures of non-caking coal with coal preparation sludge and bitumen extracted from oil sands. The coal used was from the Shubarkol'sk coal deposit (USSR); the sludge was from the Saburkhanskaya preparation plant. Properties and composition of oil-bituminous sands and of bitumen to be used as binder are given. Technological details of the briquetting and coking processes are provided. Results show that briquets produced from mixtures of coal and oil-bituminous sands can only be used as a high-ash lump fuel, which cannot be further processed into semicoke. Experiments were carried out briquetting coal or coke, sludge and 6-8% bitumen extracted from the sands, varying coal or coke grain fractions and composition of the mixture. An increased briquet strength was found after using the vacuum-distilled 300-350 C bitumen fraction. Briquets from this non-caking coal with bitumen binder are regarded as ecologically clean fuel. 5 refs.

  8. Utilization of Waste Clay from Boron Production in Bituminous Geosynthetic Barrier (GBR-B) Production as Landfill Liner

    OpenAIRE

    Müfide Banar; Yücel Güney; Aysun Özkan; Zerrin Günkaya; Eren Bayrakcı; Derya Ulutaş

    2016-01-01

    Bituminous geomembranes, one type of geosynthetics, include a hot bituminous mixture with mineral filler and reinforcement. In this study, boron production waste clay (CW) was used as filler to produce a geosynthetic barrier with bentonite, waste tire, and bitumen. Bentonite and waste tires were used as auxiliary fillers and bitumen as the binder. CW/bitumen, CW/bentonite/bitumen, and CW/waste tire/bitumen mixtures were prepared by using a laboratory mixer at 100°C. Hot mixtures were extruded...

  9. Mechanical properties of hot bituminous mixes manufactured with recycled aggregate of Silestone® waste

    Directory of Open Access Journals (Sweden)

    Rubio, M. C.

    2011-03-01

    Full Text Available This article presents the results of a research project which analyzes the viability of incorporating waste material from decorative quartz solid surfacing in the manufacture of hot bituminous mixes. For this purpose, various bituminous mixes were manufactured with waste aggregate in different percentage. A set of tests were carried out that permitted the characterization of the mechanical behavior of these mixes. The results of these tests were similar to the results obtained when conventional mixes made from virgin quarry aggregate were tested. The results for moisture sensitivity as well as for wheel track rutting on mixes showed the optimal performance of this waste material even under very demanding traffic conditions. Laboratory studies showed that the use of this waste material in the manufacture of bituminous mixes is technically viable and can provide high-quality recycled aggregates at a very low cost, which can be used in the pavement of road.

    Este artículo muestra los resultados de un proyecto de investigación que tiene por objeto analizar la viabilidad de incorporación de residuos procedentes de piedra decorativa en la fabricación de mezclas bituminosas en caliente. Para ello se fabricaron mezclas con áridos reciclados de residuos procedentes de piedra decorativa en distintos porcentajes, realizando un conjunto de ensayos que posibilitaron caracterizar el comportamiento mecánico de dichas mezclas. Los resultados obtenidos fueron similares a los de las mezclas convencionales fabricadas con áridos vírgenes procedentes de cantera. Los valores de resistencia conservada ante la acción del agua y deformación en pista, pusieron de manifiesto la aptitud del residuo incluso ante las condiciones de tráfico más exigentes. Los trabajos realizados en el laboratorio indican que la utilización del residuo en la fabricación de mezclas bituminosas es técnicamente viable, pudiendo obtenerse áridos reciclados de gran calidad y

  10. Development prospects for Bazhenov formation bituminous claystones in the southeast of the West Siberian Plate (Tomsk Region)

    International Nuclear Information System (INIS)

    The article considers the use of time-tested bituminous shale development technologies in the southeast of the West Siberian Plate (Tomsk Region). A research target is the bituminous claystones of the Bazhenov formation. The Bazhenov formation was divided into stratigraphic units, and the sequence of forming these units within the territory under study was restored on the basis of the peculiarities of the Bazhenov formation section structure with gamma-ray logging data. The joint analysis of logs (gamma-ray logging, resistivity logging, SP logging, neutron gamma-ray logging, induction logging) and core data revealed the wide development of carbonatization processes in the lower stratigraphic units of the Bazhenov formation, whereas the upper, most bituminous units do not have the signs of carbonatization. It is a favorable factor for using the existing technologies of producing hydrocarbons from analogous sedimentary deposits. Considering the degree of lithological disconnection of an oilbearing object from adjacent reservoir formations allows making a conclusion that the application of the existing technologies for developing bituminous claystones can be implemented only in the insignificant territory of the area under study where the Bazhenov formation overlies Georgiev formation claystones being over 8 meters thick. To develop the oil and gas potential of the Bazhenov formation in other territories, there will be a need for new technologies that allow forming a fracture-cavernous matrix in a carbonate rock

  11. Examination and comparision of structure: lignite, bituminous and anthracite coal. [10 references

    Energy Technology Data Exchange (ETDEWEB)

    Winans, R.E.; Hayatsu, R.; Scott, R.G.; Moore, L.P.; Studier, M.H.

    1976-01-01

    Coal can be described as an amorphous mixture of macromolecules each made up of a complex array of organic molecules chemically linked together. Methods for breaking up these macromolecules in order to characterize the aromatic structural types have been explored. Pyrolysis is a common method for depolymerizing coal, but under the conditions necessary for pyrolysis much structural rearrangement occurs making a comparison of the products to the initial structural groups in coal difficult if not impossible. One approach has been to use a variety of selective oxidation methods. Aqueous sodium dichromate, aqueous air oxidation with uv light, and hydrogen peroxide in acetic acid have been used. Initial results of some of these studies have been published. This work has been extended to include characterization and comparison of a lignite, bituminous coal, and anthracite. Besides the oxidation products, the monomeric organic molecules trapped within the macromolecules are examined and the results interpreted in relation to coal structure and the coalification process.

  12. Bituminization of simulated waste, spent resins, evaporator concentrates and animal ashes by extrusion process

    International Nuclear Information System (INIS)

    The results of the study of bituminization of simulated radwaste - spennt ion-exchange resins, borate evaporator/concentrates and animal ashes, are presented and discussed. Distilled and oxidizer bitumen were used. Characterization of the crude material and simulated wastes-bitumen mixtures of varying weigt composition (30, 40, 50, 60% by weight of dry waste material) was carried out. The asphaltene and parafin contents in the bitumens were also determined. Some additives and were used with an aim to improve the characteristcs of solidified wastes. For leaching studies, granular ion-exchange resins were with Cs - 134 and mixtures of resin-bitumen were prepared. The leaching studies were executed using the IAEA recommendation and the ISO method. A conventional screw-extruder, common in plastic industry, was used determine operational parameters and process difficulties. Mixtures of resin-bitumen and evaporator concentrate-bitumen obtained from differents operational conditions were characterized. (Author)

  13. Physical properties of solid fuel briquettes from bituminous coal waste and biomass

    Institute of Scientific and Technical Information of China (English)

    ZARRINGHALAM-MOGHADDAM A; GHOLIPOUR-ZANJANI N; DOROSTIS; VAEZ M

    2011-01-01

    Biomass and bituminous coal fines from four different coalfields were used to produce fuel briquettes.Two physical properties of briquettes,water resistance index and compressive strength were analyzed.The influence of type and quantity of biomass on physical properties was also studied.The results reveal that depending on the mineral content of the coal,the physical properties of the briquettes differ noticeably.The comparison of briquettes with and without biomass showed that the presence of the beet pulp increased CS in all types of coal samples.Samples containing beet pulp had better physical properties than sawdust.Mezino Ⅱ coal briquettes had highest CS and WRI than the other ones.Calorific value of biomass/Mezino Ⅱ coal briquettes was lessened in comparison with raw coal,but it remained in an acceptable range.

  14. Combustion characteristics and arsenic retention during co-combustion of agricultural biomass and bituminous coal.

    Science.gov (United States)

    Zhou, Chuncai; Liu, Guijian; Wang, Xudong; Qi, Cuicui; Hu, Yunhu

    2016-08-01

    A combination of thermogravimetric analysis (TG) and laboratory-scale circulated fluidized bed combustion experiment was conducted to investigate the thermochemical, kinetic and arsenic retention behavior during co-combustion bituminous coal with typical agricultural biomass. Results shown that ignition performance and thermal reactivity of coal could be enhanced by adding biomass in suitable proportion. Arsenic was enriched in fly ash and associated with fine particles during combustion of coal/biomass blends. The emission of arsenic decreased with increasing proportion of biomass in blends. The retention of arsenic may be attributed to the interaction between arsenic and fly ash components. The positive correlation between calcium content and arsenic concentration in ash suggesting that the arsenic-calcium interaction may be regarded as the primary mechanism for arsenic retention. PMID:27136608

  15. Application of laser microprobe (LAMMA 1000) to "fingerprinting" of coal constituents in bituminous coal

    Science.gov (United States)

    Lyons, P.C.; Hercules, D.M.; Morelli, J.J.; Sellers, G.A.; Mattern, D.; Thompson-Rizer, C. L.; Brown, F.W.; Millay, M.A.

    1987-01-01

    A laser microprobe (LAMMA-1000) microchemical analysis of vitrinites of different morphologies but similar reflectances within the same bituminous coal bed indicates distinct "fingerprint" spectra. The banded form of vitrinite contains Li, Ti, Ba, Sr, F, and Cl which were not detected in the nonbanded vitrinite. These differences may indicate a different plant source or the introduction of these elements from fluids mobilized during diagenesis. The nonbanded vitrinite (called corpocollinite), which was contained in a pyrite coal-ball seed fern permineralization of Myeloxylon, may have been protected from influx of these elements due to entrapment by pyrite during an early peat stage. An ion at M/Z 65, which is characteristic of the banded vitrinite, may indicate C5H5+ and, perhaps a difference in the chemical structure of the two vitrinites. These results demonstrate that "fingerprint" spectra can be obtained from vitrinite macerals by LAMMA and that these "fingerprints" have genetic implications. ?? 1987.

  16. Progress in developing a model for interaction of bituminized waste products with water

    International Nuclear Information System (INIS)

    The reported work is part of a study of long-term properties of bituminized waste products. The long-term goal is: - estimating the swelling and degradation of an agglomerate of ion exchange resins and bitumen when submerged in water, - estimating the consequent pressure build-up and degradation of surrounding barriers in the repository. The report describes the first steps in calculating diffusion of water into the heterogeneous medium of ion exchange resins and bitumen and the consequent swelling of the material. Different models for the effective diffusivity are applied and implemented into a new version of the code GEOPATH which then also considers the swelling due to water uptake. Two-dimensional cylindrical geometry is considered. Results from some test calculations are shown. It is concluded that swelling is an important effect which can be handled theoretically if basic data are available. (authors)

  17. Comparative study of test methods for bituminized and other low- and medium-level solidified waste materials

    International Nuclear Information System (INIS)

    Various aspects of the behaviour of bituminized or cemented simulated low- or medium-level radioactive waste in contact with water or salt solutions have been investigated. The solubility (approximately 0.5%) and the diffusion coefficient (approximately 5.10-8 cm2/sec) determining transort of water in pure bitumen have been measured for Mexphalte 40/50 at room temperature. A weighing method has been used to study water uptake and swelling of bituminized sodium nitrate, sodium sulphate or cation-exchange resin. The swelling of samples in contact with water was in some cases very pronounced. In strong salt solutions the tendency to swell is much less. The particle size of the embedded waste material is an important parameter. Thermal pre-treatment of cation-exchange resin before bituminization does not seem to improve the quality of the final product. The interaction between bituminized-exchange resin and concrete barrier materials has been studied. Microbial degradation of bitumen and bituminized waste under aerobic conditions has been investigated. It is probably of minor importance as far as leaching is concerned. A method for measuring leaching from a plane surface of cemented waste has been developed. The method avoids the problem of cracks between the sample and the container. Leaching from cemented sodium nitrate or sulphate was investigated. Absorption of CO2 from the atmosphere was found to have only minor effect on Cs- and Na-leaching but gave a pronounced decrease in Ca-leaching. The use of silica-fume as an additive to cemented sodium nitrate decreased the leach rate by a factor 4. (author)

  18. Uraniferous lignites and bituminous clays of the Serres Basin. Pt. A

    International Nuclear Information System (INIS)

    The lignites of the southern area (Christos-Vissiani-Lefkes-Perdikari) and the bituminous clay silts of the northern area (Maramena, Ano Metohi, Chrysopigi) are the main uraniferous beds in the Serres Basin. The sediments of the basin (Upper Miocene to recent) have been stratigraphically divided into three informal unities: the Lefkon, Georgios and Spilia formations. The uraniferous lignites pertaining to the Lefkon limnic-fluvial formation are developed into two discrete horizons, the upper Double Seam and the lower Main Seam. The bituminous clays are of the same age with the lignites, those of Maramena being, however, younger, equivalent to the marine and brackish Georgios formation. The continuity, thickness and dip of the strata reveal considerable regional changes resulting from the intense tectonism of the basin. Further to the surface works the upper lignites have been reached through small excavations and also about 100 boreholes totalling 10,000 m have been drilled. The composition of the organic constituents and the calorific value show a dull transitional to shiny hard lignite with ash rich in pyrite and sulphur. There have been no discrete U minerals detected, while the electron microprobe analysis showed that the uranium is uniformly disseminated into the lignite mass, mainly absorbed through its humic acids. More than 75% of the uranium is extractable, the control of its combustion conditions being, however, a major problem. The potential reserves have been up to date estimated to be of over 4,000 tons (uranium metal), this figure resulting mainly from data evaluated from the borehole γ-ray logs using the computer programmes LOGFILE and LOGPLOT developed at the Radioactive Raw Materials Dept. of the Greek AEC. (author)

  19. Distribution of inorganic and organic substances in the hydrocyclone separated Slovak sub-bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Anton Zubrik; Slavomir Hredzak; Ludmila Turcaniova; Michal Lovas; Ingo Bergmann; Klaus Dieter Becker; Maria Lukcova; Vladimir Sepelak [Slovak Academy of Sciences, Kosice (Slovakia). Institute of Geotechnics

    2010-08-15

    A low-rank Slovak sub-bituminous coal from the Handlova deposit was physically treated by washing in a water-only cyclone with the goal to find the separation effect for inorganic (mainly Fe-bearing minerals) and organic substances (humic acids, diterpanes). A high-quality coal product with the ash content in the dry matter of 9.02% and carbon content of C{sup d} = 68.12% at a mass yield of 29.51% was obtained using the water-only cyclone processing. At first, the physically treated coal samples were detailed characterized by XRD, {sup 57}Fe Moessbauer spectroscopy, FT-IR and HR-TEM. In addition to non-crystalline organic coal components, inorganic compounds belonging to silicate minerals (kaolinite, muscovite and quartz) as well as to Fe-bearing sulphide minerals (pyrite) were identified in the sub-bituminous coal by XRD. {sup 57}Fe Moessbauer spectroscopy detected the presence of iron carbonate (siderite), iron-containing clay mineral and two sulphur-containing minerals (pyrite, jarosite) in the untreated coal. On the other hand, only one Fe-bearing mineral, (pyrite) was found in the washed coal. Effect of the physical separation is also demonstrated in FT-IR spectra, where the peak at 1040 cm{sup -1} representing the silicate component in the untreated sample is not detectable in the washed coal sample. Presence of extractive organic substances, i.e. humic acids and tetracyclic diterpane (16a(H)-phyllocladane), in the hydrocyclone products is also evidenced. It was confirmed that the isolated diterpenoic compound is attendant in the washed product with the lowest ash content and it is assimilated with the organic part of coal. Surprisingly, humic acids were found in the highest concentration in the slurry that has the highest content of ash (63.14%). 54 refs., 8 figs., 5 tabs.

  20. Inoculum density of Glomus mosseae and growth of onion plants in unsterilized bituminous coal spoil

    Energy Technology Data Exchange (ETDEWEB)

    Khan, A.G.

    1988-01-01

    The effect of inoculum, density (number of vesicular-arbuscular mycorrhizal (VAM) propagules g/sup -1/ of inoculum) on the growth of onions (Allium cepa L.) infected by Glomus mosseae (Nicol and Gerd). Gerdemann and Trappe, Comb nov in unsterilized coal spoil containing indigenous VAM fungi, including G. mosseae, was investigated. The amount of onion roots converted to mycorrhizas by inoculant fungus, estimated by a gridline intersect method, increased with inoculum density (..gamma..0.62, P0.05) until a plateau was reached. Onion growth responses also increased significantly (P<0.05) with the amount of VAM inoculum present in the coal spoil. The initial linear relationship between inoculum propagules (MPN estimates), percent colonization of onion roots and onion shoot dry weight became quadratic as the number of infection propagules increased. VAM infection had no significant effect on root:shoot ratios. Similarly there was no significant interaction (P>0.05) between the inoculum density, VAM-colonized root mass and the onion root:shoot fresh weight ratios. The amount of the windswept bituminous coal spoil bound to VAM (presumably because of VAM external hyphae) also increased as inoculum density increased (..gamma..0.63, P<0.05). There was a stronger correlation (ga0.85, P<0.05) between the amount of spoil adhered per plant and the root fresh wt plant/sup -1/ indicating that root effects were primarily responsible for increasing spoil adherence. There were negative correlations (P<0.05) between root fresh wt plant/sup -1/ (..gamma..-0.68), inoculum density (..gamma..-0.589), percent root elngth infected (..gamma..-0.73) and the amount of spoil adhered g/sup -1/ root fresh wt. The possible exploitation of VAM in revegetation of bituminous coal spoil is discussed. 25 refs., 2 tabs.

  1. The effect of petrographical composition of coals and bituminous sediments on the material and isotopic composition of dry natural gases from artificial recoalification reactions. 2

    International Nuclear Information System (INIS)

    Experimental results indicate that on the basis of the material and isotopic composition of natural gases conclusions can be drawn with regard to the character (humic or bituminous) of the parent rock. Thus, genetic relations assumed to exist between humic sediments (e.g. coal seams) and dry natural gases as well as bituminous rocks and wet natural gases are experimentally confirmed. In addition, from analyses of the materials approximate data can be derived on the degree of carbonization of coal or bituminous sediments in the main phase of gas separation. Furthermore, these analyses were used to elucidate the question whether authochthonous or allochthonous deposits are present. It could be shown that the maceral composition of coals and of the organo-petrographical inclusions in bituminous sediments determines the isotopic composition of methane in recoalification gases to a considerable degree. (author)

  2. Effect of organic calcium compounds on combustion characteristics of rice husk, sewage sludge, and bituminous coal: thermogravimetric investigation.

    Science.gov (United States)

    Zhang, Lihui; Duan, Feng; Huang, Yaji

    2015-04-01

    Experiments were conducted in a thermogravimetric analyzer to assess the enhancement of combustion characteristics of different solid fuels blended with organic calcium compounds (OCCs). Rice husk, sewage sludge, and bituminous coal, and two OCC were used in this study. Effect of different mole ratios of calcium to sulfur (Ca/S ratio) on the combustion characteristics were also investigated. Results indicated that combustion performance indexes for bituminous coal impregnated by OCC were improved, however, an inverse trend was found for sewage sludge because sewage sludge has lower ignition temperature and higher volatile matter content compared to those of OCC. For rice husk, effect of added OCC on the combustion characteristics is not obvious. Different solid fuels show different combustion characteristics with increases of Ca/S ratio. The maximum combustion performance indexes appear at Ca/S ratios of 1:1, 2:1, and 3:1 for OCC blended with Shenhua coal, rice husk, and sewage sludge, respectively. PMID:25638405

  3. The bituminization in Marcoule and la Hague plants. Description of the processes and the fire risk prevention

    International Nuclear Information System (INIS)

    Chemical precipitation is an efficient process to decontaminate liquid effluents and has been selected as early as 1966 for the liquid waste treatment of MARCOULE. The process has been designed by the French CEA and improved along the time. The first implementation in LA HAGUE was for the STE 2 facility (Station de Traitement d'Effluents no 2). A new facility, STE 3, has been commissioned in 1989 in LA HAGUE, benefiting from these previous experience and therefore contributing into a drastic reduction of liquid discharges. The sludges coming from the treatment in MARCOULE and STE 3 are bituminized into continuous extruders. The resulting waste is kept in interim storage, waiting for final disposal. The industrial production, up to now, is close to 10000 drums (55 gallons) in LA HAGUE and 60000 drums in MARCOULE. A retrieval operation of the MARCOULE drums from the present storage has been launched to send them into a recently built interim storage operating since the beginning of 2000. At the present time, in LA HAGUE, evaporation has been preferred to chemical precipitation for the treatment of liquid effluents. After concentration, the effluents go to the vitrification and the volume of resulting waste is much smaller. However, bituminization is still the preferred option for the 10000 m3 of sludges resulting from the STE 2 operations which are being stored in tanks. A complete reevaluation of the operation safety measures of bituminization has been made lately in both plants following recent incidents on other installations. The paper describes the chemical precipitation and the bituminization processes and focuses on safety measures which are implemented for prevention, detection and fight. (authors)

  4. Dye-adsorption capacity of bituminous fly ash and its pozzolanic property after used as dye-adsorbent

    OpenAIRE

    Penpolcharoen, M.

    2004-01-01

    Bituminous fly ash, which is an industrial waste, was used as an adsorbent to remove dyestuff from the textile-dye wastewater. The batch kinetic and isotherm experiments of the synthetic wastewater were firstly conducted to determine the adsorption behavior and optimal conditions for adsorption. The optimal conditions were then applied to the actual textile-dye wastewater. Under the original conditions of fly ash and wastewater, the results indicated that the color could be removed up to 86.6...

  5. Utilization of Waste Clay from Boron Production in Bituminous Geosynthetic Barrier (GBR-B Production as Landfill Liner

    Directory of Open Access Journals (Sweden)

    Müfide Banar

    2016-01-01

    Full Text Available Bituminous geomembranes, one type of geosynthetics, include a hot bituminous mixture with mineral filler and reinforcement. In this study, boron production waste clay (CW was used as filler to produce a geosynthetic barrier with bentonite, waste tire, and bitumen. Bentonite and waste tires were used as auxiliary fillers and bitumen as the binder. CW/bitumen, CW/bentonite/bitumen, and CW/waste tire/bitumen mixtures were prepared by using a laboratory mixer at 100°C. Hot mixtures were extruded into strips by using a lab-scale corotating twin screw extruder (L/D: 40 followed by die casting (2 mm × 100 mm. Glass fleece or nonwoven polyester was used as reinforcement material and while die casting, both sides of the reinforcement materials were covered with bituminous mixture. Thickness, mass per unit area, tensile strength, elongation at yield, and hydraulic conductivity were used to characterize the geomembranes. Among all geomembranes, nonwoven polyester covered with 30% bitumen-70% boron waste clay mixture (PK-BTM30CW70 was found to be the most promising in terms of structure and mechanical behaviour. After that, consequences of its exposure to distilled water (DW, municipal solid waste landfill leachate (L-MSW, and hazardous waste landfill leachate (L-HW were examined to use for an innovative impermeable liner on solid waste landfills.

  6. A preliminary investigation into the physical and chemical properties of biomass ashes used as aggregate fillers for bituminous mixtures.

    Science.gov (United States)

    Melotti, Roberto; Santagata, Ezio; Bassani, Marco; Salvo, Milena; Rizzo, Stefano

    2013-09-01

    Fly and bottom ashes are the main by-products arising from the combustion of solid biomass. Since the production of energy from this source is increasing, the processing and disposal of the resulting ashes has become an environmental and economic issue. Such ashes are of interest as a construction material because they are composed of very fine particles similar to fillers normally employed in bituminous and cementitious mixtures. This research investigates the potential use of ash from biomass as filler in bituminous mixtures. The morphological, physical and chemical characteristics of 21 different ashes and two traditional fillers (calcium carbonate and "recovered" plant filler) were evaluated and discussed. Leaching tests, performed in order to quantify the release of pollutants, revealed that five ashes do not comply with the Italian environmental re-use limits. Experimental results show a wide range of values for almost all the investigated properties and a low correlation with biomass type in terms of origin and chemical composition. Furthermore, sieving and milling processes were found to improve the properties of the raw material in terms of grading and sample porosity. The effectiveness of these treatments and the low content of organic matter and harmful fines suggest that most of the biomass ashes investigated may be regarded as potential replacements for natural filler in bituminous mixtures. PMID:23790672

  7. Analysis and modeling of 3D complex modulus tests on hot and warm bituminous mixtures

    Science.gov (United States)

    Pham, Nguyen Hoang; Sauzéat, Cédric; Di Benedetto, Hervé; González-León, Juan A.; Barreto, Gilles; Nicolaï, Aurélia; Jakubowski, Marc

    2015-05-01

    This paper presents the results of laboratory testing of hot and warm bituminous mixtures containing Reclaimed Asphalt Pavement (RAP). Complex modulus measurements, using the tension-compression test on cylindrical specimens, were conducted to determine linear viscoelastic (LVE) behavior. Sinusoidal cyclic loadings, with strain amplitude of approximately 50ṡ10-6, were applied at several temperatures (from -25 to +45 °C) and frequencies (from 0.03 Hz to 10 Hz). In addition to axial stresses and strains, radial strains were also measured. The complex modulus E ∗ and complex Poisson's ratios ν ∗ were then obtained in two perpendicular directions. Measured values in these two directions do not indicate anisotropy on Poisson's ratio. The time-temperature superposition principle (TTSP) was verified with good approximation in one-dimensional (1D) and three-dimensional (3D) conditions for the same values of shift factor. Experimental results were modeled using the 2S2P1D model previously developed at the University of Lyon/ENTPE. In addition, specific analysis showed that eventual damage created during complex modulus test is very small and is equivalent to the effect of an increase of temperature of about 0.25 °C.

  8. Contribution to physico-chemical study of Timahdit bituminous schists (Morocco): Organic matters and metalloporphyrins

    International Nuclear Information System (INIS)

    The Timahdit bituminous schists have been analysed by different methods. The experimental results obtained using these methods concern the behaviour of the schists and the Kerogen facing the pyrolysis, as well as the separation of the hydrocarbons and the metalloporphyrins. For this purpose the techniques used are: 'Rock Eval' pyrolysis, thermogravimetric analysis and electron paramagnetic resonance (E.P.R.) for the raw rock and the Kerogen; infrared (I.R.), gas chromatography and E.P.R. for the extracted organic matters; E.P.R., I.R., nuclear magnetic resonance (N.M.R.), ultraviolet (U.V.) and mass spectrometry for the metalloporphyrins identification and characterization. The analysis of these schists has shown that: We can extract per solvent only 1% of organic matters, ferric oxide hasn't any effect neither on the pyrolysis nor on the organic matters extraction and that the Kerogen of these schists are relatively rich in hydrocarbonic compounds. The gas chromatography reveal the presence of alkanes with odd number of carbons and isoprenoids. All these criteria indicate an immature, little developped organic matter which having probably a marine origin but possessing a good oil potential. It has also been observed that a part of Iron, Nickel and Vanadium in the schists are incorporated into the organic matters. Nickel and Vanadium are into macrocycles which are porphyrins. A method for extracting and separating these porphyrins has been developped. 43 figs., 21 tabs., 58 refs. (author)

  9. Influence of Extrusion Conditions on the Rheological Behavior of Nuclear Bituminized Waste Products

    International Nuclear Information System (INIS)

    In France, bitumen has been used since four decades as a container material for low/intermediate activity and long lifetime radionuclides. Industrial Bituminized Waste Products (BWP) are produced by continuous extrusion of 60 wt.% bitumen and 40 wt.% salts, in which a very small fraction is radioactive. These incorporated salts are, in majority, of two types: soluble or insoluble. During storage, the organic matrix subjected to irradiation produces gases, which can give rise to BWP swelling in the container and then to a possible overflow. The extent of gas production is directly linked to the degree of dispersion of the salts into the bitumen matrix. To quantify this dispersion, the effect of extrusion operating conditions, such as feed rate and screw speed, have been studied using a laboratory scale co-rotating twin screw extruder. BWP rheological characterization shows the development of a pseudo-solid plateau at low frequency and a change in the linear viscoelastic domain when screw speed and feed rate are varied, indicating a modification of the dispersion state. Samples characterization with environmental scanning electron microscopy (ESEM) confirms in the case of insoluble and soluble salts a change in the number of agglomerates, accompanied by an improvement of the dispersion at high screw speed but less remarkable with the feed rate. A Carreau-Yasuda law with a yield stress is proposed to describe the theological behaviour of these materials. The effects of volume fraction and maximum volume fraction on viscosity are described using a Krieger-Dougherty equation. (authors)

  10. Development of a method to determine the nuclide inventory in bituminized waste packages

    International Nuclear Information System (INIS)

    Until the 1980s, bitumen was used as a conditioning agent for weak to medium radioactive liquid waste. Its use can be ascribed mainly to the properties that indicated that the matrix was optimal. However, fires broke out repeatedly during the conditioning process, so that the method is meanwhile no longer permitted in Germany. There are an estimated 100 waste packages held by the public authorities in Germany that require a supplementary declaration. In contrast to the common matrices, such as for example resins or sludges, there is still no standardized technology for taking samples and subsequently determining the radio-nuclide for bitumen. Aspects, such as the thermoplastic behaviour, make determining the nuclide inventory more difficult in bituminized waste packages. The development of a standardized technology to take samples with a subsequent determination of the radio-nuclide analysis is the objective of a project funded by the BMBF. Known, new methods, specially developed for the project, are examined on inactive bitumen samples and then transferred to active samples. At first non-destructive methods are used. The resulting information forms an important basis to work out and apply destructive strategy for sampling and analysis. Since the project is on-going, this report can only address the development of the sampling process. By developing a sampling system, it will be possible to take samples from an arbitrary selected location of the package across the entire matrix level and thus gain representative analysis material. The process is currently being optimized. (orig.)

  11. Elemental analysis of Indonesian and Australian bituminous coal used at Kapar Power Station

    International Nuclear Information System (INIS)

    An instrumental neutron activation analytical (INAA) technique is used for the determination of thirty elements in five coal samples collected from Kapar power station, imported from Indonesia and Australia. Analyses of the samples are being associated with standards. All irradiation were performed in the nuclear reactor of Malaysia Nuclear Agency (MNA). samples were counted by Hyper Pure Germanium (HPGe) detector for short period irradiations at MNA, while for the long period irradiations the samples were counted at Universiti Kebangsaan Malaysia (UKM). The concentrations of thirty elements have been determined: The major components are Cl, Ca, Mg, K, Fe, Ti, and Na with the mean concentrations in the range between 70±69 ppm-6100±1639 ppm; and the trace elements are Zr, V, Mn, Sc, Cr, Co, As, Br, Rb, Sb, Ba, La, Ce, Nd, Sm, Eu, Tb, Yb, Lu, Hf, Th, U and Ta with the mean concentrations in the range between 0.1381±0.0202 - 69.0±2.8 ppm. The results have been compared to the reported data of eight coal samples from the United States and the reported data of Australian bituminous coal. (Author)

  12. Burnout behaviour of bituminous coals in air-staged combustion conditions

    Energy Technology Data Exchange (ETDEWEB)

    Kluger, F.; Spliethoff, H.; Hein, K.R.G. [University of Stuttgart, Stuttgart (Germany). Inst. of Process Engineering and Power Plant (IVD)

    2001-07-01

    In order to determine the influence on burnout by the combustion conditions and the coal preparation, three bituminous coals sold on the world market, from three different locations in Poland, South Africa, and Australia, were studied more closely. For this purpose, the coals were ground in two different particle size ranges, which, besides the influence of the combustion conditions, such a temperature, residence time, and stoichiometry, made it possible to also investigate the impact on burnout by the coal preparation. The experiments were carried out in an electrically heated entrained-flow reactor with a thermal input of 8.5 kW. The parameters for the experiments are wall temperature (1000-1350{degree}C), air ratio (0.6-1.15) and two particle sizes (70% {lt} 75 {mu}m, 90% {lt} 75 {mu}m). The results show that in general, for increasing temperatures, the burnout quality will improve. For the Australian Illawara coal, another outcome is increased NOx emissions. Lowering the air ratio in the reduction zone leads to less NOx emission but to increased unburnt matter in ash. For the smaller particle size fraction, the analysis of the different particle sizes shows an improvement of the burnout without a change in NOx emissions. 10 refs., 10 figs., 2 tabs.

  13. Recycling of polyethylene terephthalate (PET plastic bottle wastes in bituminous asphaltic concrete

    Directory of Open Access Journals (Sweden)

    Adebayo Olatunbosun Sojobi

    2016-12-01

    Full Text Available This research sheds light on the concept of eco-friendly road construction which comprises eco-design, eco-extraction, eco-manufacturing, eco-construction, eco-rehabilitation, eco-maintenance, eco-demolition, and socioeconomic empowerment. It also revealed the challenges being faced in its adoption and the benefits derivable from its application. Furthermore, the effects of recycling PET plastic bottle wastes produced in North Central Nigeria in bituminous asphaltic concrete (BAC used in flexible pavement construction were also evaluated. The mix design consists of 60/70 penetration-grade asphaltic concrete (5%, 68% coarse aggregate, 6% fine aggregate, and 21% filler using the dry process at 170°C. The optimum bitumen content (OBC for conventional BAC was obtained as 4% by weight of total aggregates and filler. Polymer-coated aggregate (PCA-modified BAC seems preferable because it has the potential to utilize more plastic wastes with a higher optimum plastic content (OPC of 16.7% by weight of total aggregates and filler compared to that of 9% by weight of OBC achieved by PMB-BAC. For both PMB- and PCA-modified BAC, an increase in air void, void in mineral aggregate, and Marshall stability were observed. Eco-friendly road construction which recycles PET wastes should be encouraged by government considering its potential environmental and economic benefits.

  14. Model formulations for the mathematical-statistical evaluation of operation data as a planning assistance in the assessment of face operations in the bituminous coal mining. Modellansaetze fuer die mathematisch-statistische Auswertung von Betriebsdaten als Planungshilfsmittel bei der Einschaetzung von Strebbetrieben im Steinkohlenbergbau

    Energy Technology Data Exchange (ETDEWEB)

    Griesenbrock, H.P.

    1982-06-14

    Regression models based on comprehensive operating data collections were developed and tested for a sure assessment of the haulage capacity of face conveyors in the Ruhr bituminous coal mining. Starting from a critical view of the previously developed models for the assessment of face operations a factorial model has been developed considering the data in the form of utilization coefficients the parameters of which are not directly but iteratively determinable.

  15. Development of refilling techniques of LA-type bituminized waste products

    International Nuclear Information System (INIS)

    In JAEA, 13,296 drums of low-radioactivity bituminized waste products (BWPs) have been stored in asphalt solidification storages. In order to effectively utilize the space of the BWP in a repository site, refilling techniques of the BWP from the drum to a box-shaped container were studied. Tentative processes, which we devised, consisted of (1) take-off of BWP from the drum, (2) separation of a post filling part from BWP and (3) refilling of BWP to a box-shaped container. Two methods for each process were selected, and work efficiencies of the methods were investigated by using a synthetic BWP. (1) Two take-off methods: one was falling down of the BWP from the drum at high temperature such as 100°C and 150°C, and the other was removing the cut drum from the BWP at low temperature. In the former case, it was found that at least 20wt% of the BWP was attached on the container. In the latter case, ca. 100wt% of the BWP was easily recovered by cutting and peeling the drum below 10°C. (2) Two separation methods: one was cutting off the post filling part by using a flat blade, and the other was crushing the post filling part by using a mechanical hammer. In the former case, the BWP could be cut in 2 h, but it was observed that some BWP was attached on the blade. In the latter case, it was found that the post filling part was easily crushed from the BWP below 0°C. (3) Two filling methods: one was filling the softened BWP by heating, and the other was pressure filling. In the both method, filling rates of the BWP were 100wt% and 98.8wt%, respectively. Volume of the BWP after the filling tests increased 6vol% and 2vol% compared to theoretical volume, respectively. (author)

  16. Study on the submicron and micron morphology and the properties of poor bituminous coal burnout

    Energy Technology Data Exchange (ETDEWEB)

    Pei-Fang Fu; Huai-Chun Zhou; Qing-Yan Fang; Hai Yao; Jianrong Qiu; Minghou Xu [Huazhong University of Science and Technology, Wuhan (China). State Key Laboratory of Coal Combustion

    2007-05-15

    Carbon burnout and its reaction mechanism have been widely focused on in the past decades. The properties of burnout, submicron and micron morphology and the reaction mechanism of poor bituminous coal/char (PBC) in a W-shaped power plant boiler was studied and was compared with those in DTF and in TGA, which showed that the degree of PBC burnout in TGA at 1450{sup o}C was greater than or approximately equal to that in a W-shaped boiler, and that the complexity of the reactions among residual char, oxygen and SiO{sub 2} did not seem to result in mass loss in TGA, although the weight percentage of the residual char in ash decreased from 33% ad (air dry basis) at 900{sup o}C to 9% and at 1450{sup o}C. According to the distribution of pores and the properties of the char burnout, the char can be simply categorized into three classes: char burnout easy, char burnout difficult and char burnout very difficult. The differences of the reaction mechanism must be considered while predicting the burning rate and degree of char burnout in a full-scale boiler by making use of experimental results from TGA and DTF. A different char particle contains markedly different amount of carbons, but for a special char particle, the ratio of carbon to ash is generally constant, and an ash shell does not exist on the char surface. The fusion mineral matter composing of C-O-Si-Al is amorphous, not in the form of Al{sub 2}O{sub 3} and SiO{sub 2} above 1450{sup o}C.

  17. Mercury speciation and distribution in a 660-megawatt utility boiler in Taiwan firing bituminous coals.

    Science.gov (United States)

    Hsi, Hsing-Cheng; Lee, Hsiu-Hsia; Hwang, Jyh-Feng; Chen, Wang

    2010-05-01

    Mercury speciation and distribution in a 660-MW tangential-fired utility boiler in Taiwan burning Australian and Chinese bituminous coal blends was investigated. Flue gases were simultaneously sampled at the selective catalytic reduction (SCR) inlet, the SCR outlet, the electrostatic precipitator (ESP) outlet, and the stack. Samplings of coal, lime, bottom ash/slag, fly ash, and gypsum slurry were also conducted. Results indicated that flue gases at the inlet to SCR contained a great potion of particle-bound mercury (Hg(p)), 59-92% of the total mercury. Removal of mercury was not observed for the SCR system. However, repartitioning of mercury species across the SCR occurred that significantly increased the portion of elemental mercury (Hg0) to up to 29% and oxidized mercury (Hg2+) to up to 33% in the SCR outlet gas. Overreporting of Hg(p) at the inlet of SCR may cause the observed repartitioning; the high ammonia/nitric oxide circumstance in the SCR unit was also speculated to cause the mercury desorption from ash particles and subsequent reentrance into the gas phase. ESP can remove up to 99% of Hg(p), and wet flue gas desulfurization (FGD) can remove up to 84% of Hg2+. Mercury mass balances were calculated to range between 81 and 127.4%, with an average of 95.7% wherein 56-82% was in ESP fly ash, 8.7-18.6% was retained in the FGD gypsum, and 6.2-26.1% was emitted from the stack. Data presented here suggest that mercury removal can be largely enhanced by increasing the conversion of Hg0 into Hg(p) and Hg2+. PMID:20480850

  18. Experimental Study on Minimum Ignition Temperature of Bituminous Coal Dust Cloud%烟煤煤尘云最低着火温度实验研究

    Institute of Scientific and Technical Information of China (English)

    邓军; 屈姣; 王秋红; 谢长春

    2014-01-01

    In this PaPer,study and measurement were carried out on the minimum ignition temPerature of three kinds of bituminous coal dust clouds by using the Godbert-Greenwald heating furnace,including the non-caking coal taken from Dafusi Mine in Binxian County,the gas coal from Kouzi East Mine in Anhui Province and the lean coal from 301 working face of Tianchi Mine in Shanxi Province. It was found out from the exPerimental results that the ash content of the gas coal,non-caking coal and lean coal increased in turn,their volatile content reduced in turn,their fixed carbon content increased in turn,and the water content of the lean coal,gas coal and non-caking coal increased in turn;the minimum ignition temPerature of the three kinds of bituminous coal dust clouds decreased with the reduction of their Particle sizes;based on their minimum ignition temPeratures,it was found out that the hardest ignited coal dust was the lean coal and the easiest ignited coal dust was gas coal. This study can Provide an exPerimental basic for the safe Production in coal mines.%为了研究彬县大佛寺矿不粘煤、安徽口孜东矿气煤、山西天池矿301工作面瘦煤等3种烟煤的煤尘云最低着火温度,实验采用Godbert-Greenwald加热炉对以上3种烟煤的煤尘云最低着火温度进行了测试。研究发现气煤、不粘煤、瘦煤的灰分依次增大,挥发分依次减小,固定碳依次增大,水分随瘦煤、气煤、不粘煤依次增大;这3种烟煤煤尘云的最低着火温度都随煤尘粒径的减小而降低;根据最低着火温度,得知煤尘云被引燃的难易程度依次为瘦煤、不粘煤、气煤。此基础研究可为煤矿的安全生产提供实验依据。

  19. Assessment of 137Cs and 90Sr leachate rate from bituminous radioactive wastes in surface soil disposal

    International Nuclear Information System (INIS)

    Experimental disposal of tested bitumen units with 107 Bq/kg 137Cs and 90Sr specific activity in surface soil was conducted to evaluate environmental impact of bituminized radioactive wastes. Calculations of volume integral were carried out using computer. Due to determination of integral numerical value it was founded, that 1.6x108 Bq enter soil from the unit during 10 years. The obtained value may be used as normalizing parameter at simulation of radionuclide leaching from monolithic forms as well as for correct selection of boundary conditions in dispersion equation at simulation of radioactive contamination migration

  20. Petrographic and Vitrinite Reflectance Analyses of a Suite of High Volatile Bituminous Coal Samples from the United States and Venezuela

    Science.gov (United States)

    Hackley, Paul C.; Kolak, Jonathan J.

    2008-01-01

    This report presents vitrinite reflectance and detailed organic composition data for nine high volatile bituminous coal samples. These samples were selected to provide a single, internally consistent set of reflectance and composition analyses to facilitate the study of linkages among coal composition, bitumen generation during thermal maturation, and geochemical characteristics of generated hydrocarbons. Understanding these linkages is important for addressing several issues, including: the role of coal as a source rock within a petroleum system, the potential for conversion of coal resources to liquid hydrocarbon fuels, and the interactions between coal and carbon dioxide during enhanced coalbed methane recovery and(or) carbon dioxide sequestration in coal beds.

  1. Behaviour of bituminized waste under gamma irradiation. Effect of STE3 decontamination process components

    International Nuclear Information System (INIS)

    Liquid wastes of light and medium activity are treated by chemical co-precipitation and sludge are mixed with bitumen. Irradiation is responsible of gas production and potential swelling of the embedded. It prevails on limitation of filling of storage containers and activity to 140 Ci. The aim of this work is the study of influence of the components of the decontamination process on the behaviour of bituminous wastes, in order to control swelling and to state radiolysis mechanisms, both for production and storage of wastes. For pure bitumen, mechanism of production of H2 and CH4 are specified. Oxygen consumption, localised on the surface of samples, leads to conversion of aromatic oils and resins to asphaltenes, by a chain reaction mechanism. CO2 et CO are reaction products of gaseous oxygen, respectively with bitumen and light hydrocarbons. The composition of bitumen is slightly modified to heavier and higher polarity products, with parallel hardening. NaNO3, Na2SO4, BaSO4, PPFNi, K2SO4, NiSO4, et diatoms DIT3R et DIC3 have strictly a dilution effect towards gas generation. CoS, above 1% embedded, strongly inhibits production of H2, CH4 and light hydrocarbons. Degradation of bitumen being reduced, a radical mechanism with both radicals H· et R· might exist. Kinetic shows that a bi-radicals mechanism (or more) is probable. In the same way, Raney's nickel induces a important decrease of production of H2, CH4 et C2, with a capacity of 7,7 ml/g. Swelling depends on dimension of sample gas production and dose rate. Solid content and particle size are not determining parameters. Low swelling is obtained for penetrability higher than 70 1/10 mm, This can be realised by addition of a solvent as TBP and by increasing temperature above 40 deg C. Rheological characterizations (oscillation and creeping mode) have not been successful to correlate swelling with a physical parameter. (author)

  2. Mechanical, sorption and transport experiments on a German high volatile bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Gensterblum, Y.; Krooss, B.M. [RWTH Aachen Univ. (Germany). Inst. of Geology and Geochemistry of Petroleum and Coal; Massarotto, Paul [Queensland Univ., Brisbane, St Lucia, QLD (Australia). School of Engineering

    2013-08-01

    A high volatile bituminous coal (vitrinite reflectance: 0.93%, carbon content: 83%) from the Prosper-Haniel mine, North Rhine-Westphalia has been studied using a comprehensive set of measurements and experimental procedures at RWTH Aachen University and the University of Queensland. Using the True Triaxial Stress Coal Permeameter (TTSCP) (Massarotto 2003) of the University of Queensland, permeability and gas displacement tests were performed on an 80 mm cube of the Prosper-Haniel coal. Extensive data sets were recorded to assess the effects of stress changes on gas transport and the impact of nitrogen, methane and CO{sub 2} sorption on the mechanical properties. We investigate the permeability coefficients for helium, nitrogen, methane and carbon dioxide measured on this sample as a function of net stress. As expected, permeability values decrease with increasing stress. Methane and nitrogen have nearly identical permeability coefficients throughout the entire net stress range, while permeability coefficients measured with helium are higher and those measured with CO{sub 2} significantly lower. During the permeability measurements with CO{sub 2} an anisotropic swelling of the coal cube by about 0.19% to 0.23% was observed. The volumetric effect (swelling) is 100 times slower than gas displacement. Simultaneous mechanical tests indicated a softening of the coal block upon exposure to CO{sub 2}. Thus, a decrease of Young's modulus (YM) of the coal cube during the CO{sub 2} flow test was observed as compared to the methane and nitrogen tests. High-pressure sorption isotherms with CH{sub 4} and CO{sub 2} were determined on different grain-size fractions of the Prosper-Haniel coal at 318K and different moisture contents. Methane sorption capacity decreases by 29% with increasing moisture content. Also, a decrease of sorption rate was observed with increasing moisture content. While sorption rates are generally faster for CO{sub 2} than for CH{sub 4}, the sorption

  3. Organic geochemistry of Upper Carboniferous bituminous coals and clastic sediments from the Lublin Coal Basin

    Science.gov (United States)

    Gola, Marek R.; Karger, Michał; Gazda, Lucjan; Grafka, Oliwia

    2013-09-01

    Bituminous coals and clastic rocks from the Lublin Formation (Pennsylvanian, Westphalian B) were subjected to detailed biomarker and Rock-Eval analyses. The investigation of aliphatic and aromatic fractions and Rock-Eval Tmax suggests that the Carboniferous deposits attained relatively low levels of thermal maturity, at the end of the microbial processes/initial phase of the oil window. Somewhat higher values of maturity in the clastic sediments were caused by postdiagenetic biodegradation of organic matter. The dominance of the odd carbon-numbered n-alkanes in the range n-C25 to n-C31 , high concentrations of moretanes and a predominance of C 28 and C29 steranes are indicative of a terrigenous origin of the organic matter in the study material. This is supported by the presence of eudesmane, bisabolane, dihydro-ar-curcumene and cadalene, found mainly in the coal samples. In addition, tri- and tetracyclic diterpanes, e. g. 16β(H)-kaurane, 16β(H)-phyllocladane, 16α(H)-kaurane and norisopimarane, were identified, suggesting an admixture of conifer ancestors among the deposited higher plants. Parameters Pr/n-C17 and Rdit in the coal samples show deposition of organic matter from peat swamp environments, with the water levels varying from high (water-logged swamp) to very low (ephemeral swamp). Clastic deposits were accumulated in a flood plain environment with local small ponds/lakes. In pond/lake sediments, apart from the dominant terrigenous organic matter, research also revealed a certain quantity of algal matter, indicated, i.a., by the presence of tricyclic triterpanes C28 and C29 and elevated concentrations of steranes. The Paq parameter can prove to be a useful tool in the identification of organic matter, but the processes of organic matter biodegradation observed in clastic rocks most likely influence the value of the parameter, at the same time lowering the interpretation potential of these compounds. The value of Pr/Ph varies from 0.93 to 5.24 and from 3

  4. Adsorption of bituminous components at oil/water interfaces investigated by quartz crystal microbalance: implications to the stability of water-in-oil emulsions.

    Science.gov (United States)

    Goual, Lamia; Horváth-Szabó, Géza; Masliyah, Jacob H; Xu, Zhenghe

    2005-08-30

    Silica-gel-coated QCM crystals oscillating in a thickness shear mode are used to measure adsorption of bituminous components in water-saturated heptol (1/1 vol ratio of a heptane/toluene mixture) at the oil/water interface. In addition to the viscoelasticity of the adsorbed film, the effects of the bulk liquid density and viscosity as well as the liquid trapped in interfacial cavities are taken into account for the calculation of adsorbed mass. Asphaltenes in heptol adsorb continuously at the oil/water interface, while resins (the surface-active species in maltenes) show adsorption saturation in the same solvent. For Athabasca bitumen in heptol, two adsorption regimes are observed depending on concentration. At low concentrations, a slow, non-steady-state, and irreversible adsorption takes place. At high concentrations, a steady-state adsorption with limited reversibility results in a quick adsorption saturation. The threshold concentration between these adsorption regimes is 1.5 wt % and 8 wt % for oil/water and oil/gold interfaces, respectively. The threshold concentration, the total adsorbed amount, and the flux of non-steady-state adsorption depend on the resin-to-asphaltene ratio. The threshold concentration is related to the earlier reported critical bitumen concentration characterizing the rigid-to-flexible transition of the interfacial film. We propose a new mechanism based on the change of the effective resin-to-asphaltene ratio with dilution to explain both the adsorption behavior and emulsion stability. PMID:16114932

  5. Characterization of burning and CO2 gasification of chars from mixtures of Zonguldak (Turkey) and Australian bituminous coals

    International Nuclear Information System (INIS)

    In this study, different mixtures (30 wt.% + 70 wt.% and 50 wt.% + 50 wt.%, respectively) of Zonguldak bituminous coal (Turkey) and an Australian bituminous coal are carbonized to obtain char samples. The ignition temperatures of the samples are determined by sending O2 onto the samples in a system designed for determining the ignition temperature. The gasification reactivity of the chars in a CO2 atmosphere is also measured at temperatures between 800 deg. C and 1050 deg. C. The relationship between the ignition temperature and the burning character of the same samples is investigated thermogravimetrically. The moisture, ash and volatile matter analyses are also performed. An increase in carbonization temperature leads to a decrease in the amount of volatile matter. The differences between the effects of volatile matter on the ignition temperature and the gasification reactivity of the samples with CO2 might be explained by the change in pore structure and the varying catalytic effect of mineral components in the structure. It is also seen that there is a good correlation between the thermal analysis and the complete analysis results of the samples

  6. Single particle ignition and combustion of anthracite, semi-anthracite and bituminous coals in air and simulated oxy-fuel conditions

    OpenAIRE

    Riaza Benito, Juan; Khatami, Reza; Levendis, Yiannis A.; Álvarez González, Lucía; Gil Matellanes, María Victoria; Pevida García, Covadonga; Rubiera González, Fernando; Pis Martínez, José Juan

    2014-01-01

    A fundamental investigation has been conducted on the combustion behavior of single particles (75–150 μm) of four coals of different ranks: anthracite, semi-anthracite, medium-volatile bituminous and high-volatile bituminous. A laboratory-scale transparent laminar-flow drop-tube furnace, electrically-heated to 1400 K, was used to burn the coals. The experiments were performed in different combustion atmospheres: air (21%O2/79%N2) and four simulated dry oxy-fuel conditions: 21%O2/79%CO2, 30%O2...

  7. Petrography and geochemistry of Oligocene bituminous coal from the Jiu Valley, Petrosani basin (southern Carpathian Mountains), Romania

    Energy Technology Data Exchange (ETDEWEB)

    Belkin, Harvey E.; Tewalt, Susan J. [U.S. Geological Survey, 956 National Center, Reston, VA 20192 (United States); Hower, James C. [University of Kentucky Center for Applied Energy Research, 2540 Research Park Drive, Lexington, KY 40511 (United States); Stucker, J.D. [University of Kentucky Center for Applied Energy Research, 2540 Research Park Drive, Lexington, KY 40511 (United States); University of Kentucky Department of Earth and Environmental Sciences, Lexington, KY 40506 (United States); O' Keefe, Jennifer M.K. [Morehead State University, Morehead, KY, 40351 (United States); Tatu, Calin A. [University of Medicine and Pharmacy, Department of Immunology, Clinical Laboratory No. 1, Pta. E. Murgu No. 2, RO-1900 Timisoara (Romania); Buia, Grigore [University of Petrosani, Department of Geology, University St. 20, RO-2675 Petrosani (Romania)

    2010-05-01

    Belt samples of Oligocene (Chattian) bituminous coal from 10 underground mines located in the Jiu Valley, Hunedoara County, Petrosani basin, Romania, have been examined and analyzed for proximate and ultimate analysis, major-, minor- and trace-element chemistry, organic petrography, and vitrinite reflectance. The mineral chemistry and mode of occurrence of trace elements also have been investigated using SEM and electron microprobe techniques. Twenty coal beds occur in the Jiu Valley and most of the samples are from bed no. 3, the most productive bed of the Dilja-Uricani Formation of Oligocene age. The Petrosani basin, oriented SW-NE, is 48-km long, 10-km wide at the eastern part and 2-km wide at the western part. The coal mines are distributed along the center of the valley generally following the Jiu de Vest River. Reflectance measurements indicate that the rank of the coals ranges from high-volatile B to high-volatile A bituminous. Overall, rank decreases from the southwest to the northeast. In bed no. 3, R{sub max} varies from 0.75% in the northeast to 0.93% in the southwest. Although, most Oligocene coals in Romania and adjacent countries are lignite in rank, the Jiu Valley bituminous coals have been affected by regional metamorphism and attending hydrothermal fluids related to the Alpine orogenic event. The coals are all dominated by vitrinite; resinite and funginite are important minor macerals in most of the coals. Pyrite and carbonate generally dominate the mineral assemblages with carbonate more abundant in the northwest. Siderite occurs as nodules and masses within the macerals (generally vitrinite). Dolomite and calcite occur as fracture fillings, plant-cell fillings, and in other authigenic forms. Late-stage fracture fillings are siderite, dolomite, calcite, and ankerite. In one instance, two populations of siderite ({proportional_to} 35 and {proportional_to} 45 wt.% FeO) plus ankerite fill a large fracture. Late-stage pyrite framboid alteration is Ni

  8. Dependence of carbon dioxide sorption on the petrographic composition of bituminous coals from the Czech part of the Upper Silesian Basin, Czech Republic

    Czech Academy of Sciences Publication Activity Database

    Weishauptová, Zuzana; Sýkorová, Ivana

    2011-01-01

    Roč. 90, č. 1 (2011), s. 312-323. ISSN 0016-2361 R&D Projects: GA ČR GA106/08/1146; GA AV ČR IAA300460804 Institutional research plan: CEZ:AV0Z30460519 Keywords : bituminous coal * sorption capacity * maceral composition Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.248, year: 2011

  9. Effect of structural alteration on the macromolecular properties of brown and bituminous coals, quantitative relationships to the hydrogenation reactivity with tetralin

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, P.N.; Kuznetsova, L.I. [Inst. of Chemistry and Chemico-Metallurgical Processes, Krasnoyarsk (Russian Federation); Bimer, J.; Salbut, P.D. [Inst. of Organic Chemistry, Warszawa (Poland); Gruber, R. [Univ. de Metz (France)

    1996-12-31

    The mobility of macromolecular network has been found to be the fundamental property of both brown and bituminous coals governing the reactivity for hydrogenation with tetralin. In Kansk-Achinsk brown coal, this was primarily affected by carboxylate cross-linking via polyvalent cations like Ca.

  10. Comparative study of thermal properties of bio-coal from aromatic spent with low rank sub-bituminous coals.

    Science.gov (United States)

    Yadav, Vineet; Baruah, B P; Khare, Puja

    2013-06-01

    In present investigation, biocoal samples were prepared from aromatic plant waste of two perennial grasses, i.e. Cymbopogon flexuosus (lemongrass) and Vetiveria zizanioides (khus) after oil extraction, root of Rosa damascene (rose), bark of Eucalyptus citriodora. These biocoals were characterized by proximate, ultimate, metal, thermogravimetric analysis (TGA), Fourier Transform Infra Red (FTIR) spectroscopy and ash analyses. Activation energies, initial temperature of devolatilization, maximum rate of weight loss (Rmax), fouling, slagging and alkali index were determined on the basis of TGA and ash analysis. These biocoals have good calorific values. There is possibility of slagging and fouling in combustion system but it is not severe. Owing to their similar fuel properties as high sulphur sub-bituminous coal, they can be good candidates for co-firing. Blending of these biocoals with high sulphur coals will serve dual purpose as (i) alternate fuel, and (ii) reduction in SO2 emission. PMID:23603187

  11. Combustion characteristics of Malaysian oil palm biomass, sub-bituminous coal and their respective blends via thermogravimetric analysis (TGA).

    Science.gov (United States)

    Idris, Siti Shawalliah; Rahman, Norazah Abd; Ismail, Khudzir

    2012-11-01

    The combustion characteristics of Malaysia oil palm biomass (palm kernel shell (PKS), palm mesocarp fibre (PMF) and empty fruit bunches (EFB)), sub-bituminous coal (Mukah Balingian) and coal/biomass blends via thermogravimetric analysis (TGA) were investigated. Six weight ratios of coal/biomass blends were prepared and oxidised under dynamic conditions from temperature 25 to 1100°C at four heating rates. The thermogravimetric analysis demonstrated that the EFB and PKS evolved additional peak besides drying, devolatilisation and char oxidation steps during combustion. Ignition and burn out temperatures of blends were improved in comparison to coal. No interactions were observed between the coal and biomass during combustion. The apparent activation energy during this process was evaluated using iso-conversional model free kinetics which resulted in highest activation energy during combustion of PKS followed by PMF, EFB and MB coal. Blending oil palm biomass with coal reduces the apparent activation energy value. PMID:22944493

  12. Effect of oxidation on the chemical nature and distribution of low-temperature pyrolysis products from bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E.; MacPhee, J.A.; Vancea, L.; Ciavaglia, L.A.; Nandi, B.N.

    1983-04-01

    Two bituminous coals, a high volatile Eastern Canadian and a medium volatile Western Canadian, were used to investigate the effect of oxidation on yields and chemical composition of gases, liquids and chars produced during coal pyrolysis. Pyrolysis experiments were performed at 500 C using the Fischer assay method. Mild oxidation of coals resulted in a decrease of liquid hydrocarbon yields. Further coal oxidation increased the proportion of aromatic carbon in liquid products as determined by N.M.R. and also increased the content of oxygen in liquid products. The content of oxygen in chars was markedly lower than in corresponding coals. An attempt is made to explain reactions occurring during oxidation and subsequent pyrolysis of coal on the basis of differences in chemical composition of gases, liquids and chars. (19 refs.)

  13. Effect of oxidation on the chemical nature and distribution of low-temperature pyrolysis products from bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E.; Ciavaglia, L.A.; MacPhee, J.A.; Nandi, B.N.; Vancea, L.

    1983-04-01

    Two bituminous coals, a high volatile Eastern Canadian and a medium volatile Western Canadian, were used to investigate the effect of oxidation on yields and chemical composition of gases, liquids and chars produced during coal pyrolysis. Pyrolysis experiments were performed at 500/sup 0/C using the Fischer assay method. Mild oxidation of coals resulted in a decrease of liquid hydrocarbon yields. Further coal oxidation increased the proportion of aromatic carbon in liquid products as determined by n.m.r., and also increased the content of oxygen in liquid products. The content of oxygen in chars was markedly lower than in corresponding coals. An attempt is made to explain reactions occurring during oxidation and subsequent pyrolysis of coal on the basis of differences in chemical composition of gases, liquids and chars.

  14. Development of new non destructive methods for bituminized radioactive waste drums characterization; Developpement de nouvelles methodes de caracterisation non destructive pour des dechets radioactifs enrobes dans du bitume

    Energy Technology Data Exchange (ETDEWEB)

    Pin, P

    2004-10-15

    Radioactive waste constitute a major issue for the nuclear industry. One of the key points is their characterization to optimize their management: treatment and packaging, orientation towards the suited disposal. This thesis proposes an evaluation method of the low-energy photon attenuation, based on the gamma-ray spectra Compton continuum. Effectively, the {sup 241}Am measurement by gamma-ray spectrometry is difficult due to the low energy of its main gamma-ray (59.5 keV). The photon attenuation strongly depends on the bituminous mix composition, which includes very absorbing elements. As the Compton continuum also depends on this absorption, it is possible to link the 59.5 keV line attenuation to the Compton level. Another technique is proposed to characterize uranium thanks to its fluorescence X-rays induced by the gamma emitters already present in the waste. The uranium present in the drums disturbs the neutron measurements and its measurement by self-induced X-ray fluorescence allows to correct this interference. Due to various causes of error, the total uncertainty is around 50 % on the activity of the radioisotope {sup 241}Am, corrected by the peak to Compton technique. The same uncertainty is announced on the uranium mass measured by self induced X-ray fluorescence. As a consequence of these promising results, the two methods were included in the industrial project of the 'Marcoule Sorting Unit'. One major advantage is that they do not imply any additional material because they use information already present in the gamma-ray spectra. (author)

  15. Techno-economic Comparison of IGCC Systems Employing Bituminous and Lignite%基于烟煤、褐煤的IGCC系统技术经济性对比

    Institute of Scientific and Technical Information of China (English)

    李政; 梁心玉; 薛亚丽

    2012-01-01

    近年来,褐煤提质技术的发展使得褐煤的高效利用成为可能。基于一种先进的褐煤干燥技术—内部废热利用流化床干燥(wirbelschicht-trocknung mit interner abw rmenu-tzung,WTA),采用ASPEN Plus软件及美国电力研究协会(electric power research institute,EPRI)的技术评价准则(technical assessment guide,TAG),分别对烟煤整体煤气化联合循环(integrated gasification combined cycle,IGCC)电站和褐煤IGCC电站进行技术经济性分析。详细介绍了WTA单元及燃气轮机变工况的建模方法。计算结果表明,引入WTA技术后,褐煤IGCC电站的发电效率比采用传统干燥方式时约提高4.6个百分点,整体性能与烟煤IGCC电站相差不大;而褐煤IGCC电站的发电成本比烟煤IGCC电站低24.4%。高效的褐煤干燥技术能显著提高褐煤IGCC电站的效率,而褐煤低廉的价格又对降低发电成本十分有利,褐煤很可能成为比烟煤更适合IGCC的燃料。%The development of lignite upgrading has enabled the efficient utilization of lignite recently.Based on the description of an advanced lignite drying techniquewirbelschicht-trocknung mit interner abw rmenutzung(WTA),techno-economic analysis of two integrated gasification combined cycle(IGCC) systems employing bituminous and lignite were performed by using ASPEN Plus software and the EPRI technical assessment guide.The WTA model and gas turbine off-design model were explained in detail.The result shows that pre-drying lignite by WTA can increase the net thermal efficiency of lignite IGCC power plant by up to 4.6% points compared to traditional lignite drying technology,making the performance of lignite IGCC as good as bituminous IGCC;but the cost of electricity of lignite IGCC is 24.4% lower than that of bituminous IGCC.Advanced drying technique can improve the performance of lignite IGCC and lignite’s cheap price helps to bring down the cost of electricity.Therefore lignite is

  16. chemo-Hydro-mechanical modelling of in-situ disposal of a bituminized radioactive waste in boom clay

    International Nuclear Information System (INIS)

    Document available in extended abstract form only. The current reference solution of the Belgian Agency for the Management of Radioactive Waste and Fissile Materials (ONDRAF/NIRAS) envisages underground disposal of Eurobitum Bituminized radioactive Waste (BW) in a geologically stable clay formation. In Belgium, the Boom Clay, which is a 30 to 35 million years old and ∼100 m thick marine sediment is being studied as a potential host formation because of its favorable properties to limit and delay the migration of the leached radionuclides to the biosphere over extended periods of time. The current disposal concept foresees that several drums (220 litres) of Eurobitum would be grouped in thick-walled cement-based secondary containers, which in turn would be placed in concrete-lined disposal galleries that are excavated at mid-depth in the clay layer. Only 80-90 % of the total volume of the drum is filled with Eurobitum.The remaining voids between the containers would be backfilled with a cement-based material. The interaction between the BW and the host clay formation is a very complicated chemo-hydro-mechanical process and depends not only on the hydro-mechanical behaviour of the Boom Clay itself, but also on that of the BW. In fact, the osmosis-induced uptake of water by the dehydrated hygroscopic salts embedded in the waste induces a geo-mechanical perturbation of the host formation, caused by the swelling and the increase of the pressure in and around the waste. The objectives of the Chemo-Hydro-Chemical (CHM) analysis presented in this work are (i) to get insights on the kinetics of water uptake by BW, dissolution of the embedded NaNO3 crystals, solute leaching, and maximum generated pressure under disposal conditions and (ii) to study the stress redistribution due to the recompression of the clay around a gallery caused by the swelling pressure of the bitumen and the admissible swelling pressure for Boom clay. Firstly, a CHM formulation of chemically and

  17. Bituminous solidification, disposal, transport and burial of spent ion-exchange resins. Part of a coordinated programme on treatment of spent ion exchange resins

    International Nuclear Information System (INIS)

    The project dealing with the incorporation of spent ion-exchange resins into bitumen was performed within the Agency coordinated research programme on treatment of spent ion-exchange resins. Physical and chemical properties of commercial ion-exchange resins, bitumens and bituminized resins were studied. It was shown that bitumen with low oil content and with a softening point of 60-70 deg. C are applicable for the incorporation of resins. The final waste form is allowed to contain maximum 50% resin. The comprehensive study of the biological resistance of B-30 bitumen was performed. That showed that any bacteriological attack can be regarded as generally insignificant. A continuously operating technology was realized on a semi-plant scale. The best operating conditions of this technology were determined. On the basis of the experience gained from the experiments a design of the bituminization plant of 50m3 dry resin/year treatment capacity was proposed

  18. Advances in Interlaboratory Testing and Evaluation of Bituminous Materials State-of-the-Art Report of the RILEM Technical Committee 206-ATB

    CERN Document Server

    Bahia, Hussain; Canestrari, Francesco; Roche, Chantal; Benedetto, Hervé; Piber, Herald; Sybilski, Dariusz

    2013-01-01

    This STAR on asphalt materials presents the achievements of RILEM TC 206 ATB, acquired over many years of interlaboratory tests and international knowledge exchange. It covers experimental aspects of bituminous binder fatigue testing; the background on compaction methods and imaging techniques for characterizing asphalt mixtures including validation of a new imaging software; it focuses on experimental questions and analysis tools regarding mechanical wheel tracking tests, comparing results from different labs and using finite element techniques. Furthermore, long-term rutting prediction and evaluation for an Austrian road are discussed, followed by an extensive analysis and test program on interlayer bond testing of three different test sections which were specifically constructed for this purpose. Finally, the key issue of manufacturing reclaimed hot mix asphalt in the laboratory is studied and recommendations for laboratory ageing of bituminous mixtures are given.

  19. Evaluation of bituminized waste reactivity; Maitrise de la reactivite thermique lors de l'elaboration d'un conditionnement de dechets radioactifs par le bitume

    Energy Technology Data Exchange (ETDEWEB)

    Camaro, S.; Moulinier, D. [CEA Saclay, Dept. d' Entreposage et de Stockage des Dechets (DCC/DESD/SEP), 91 - Gif-sur-Yvette (France)

    2000-07-01

    The bituminization process has been used for conditioning low and medium level (LML) radioactive waste, particularly to immobilize coprecipitation slurries and evaporation concentrates generated by effluent treatment. The process consists in mixing bitumen matrix with inactive soluble and slightly soluble salts added to insolubilize the radionuclides or resulting from the neutralization of acid effluents. This operation is performed at a sufficient temperature - depending on waste composition and bitumen grade to ensure the flow of the resulting mixture into metal containers. Exothermicity due to salts/salts or salts/bitumen reactions depending on the type of waste can be induced during or after the mixing step. This could produce an additional heat emission that the drum must be able to release to avoid a potentially incidental pattern with ignition risk, explaining why the CEA has been involved in evaluating the thermal reactivity of bituminized waste and its repercussions on the bituminization process. Given the difficulty of discriminating each exothermal reaction, the characterization of a global reactivity appears as a further precautionary measure, in addition to the definition of a working safety margin. The CEA has accordingly developed studies on this aspect. The article discusses the experimental methodology developed for the determination of the global reactivity. (authors)

  20. Utilising neural networks and closed form solutions to determine static creep behaviour and optimal polypropylene amount in bituminous mixtures

    Directory of Open Access Journals (Sweden)

    Serkan Tapkın

    2012-12-01

    Full Text Available The testing procedure in order to determine the precise mechanical testing results in Marshall design is very time consuming. Also, the physical properties of the asphalt samples are obtained by further calculations. Therefore if the researchers can obtain the stability and flow values of a standard mixture with the help of mechanical testing, the rest of the calculations will just be mathematical manipulations. Determination of mechanical testing parameters such as strain accumulation, creep stiffness, stability, flow and Marshall Quotient of dense bituminous mixtures by utilising artificial neural networks is important in the sense that, cumbersome testing procedures can be avoided with the help of the closed form solutions provided in this study. Marshall specimens, prepared by utilising polypropylene fibers, were tested by universal testing machine carrying out static creep tests to investigate the rutting potential of these mixtures. On the very well trained data basis, artificial neural network analyses were carried out to propose five separate models for mechanical testing properties. The explicit formulation of these five main mechanical testing properties by closed form solutions are presented for further use for researches.

  1. Dye-adsorption capacity of bituminous fly ash and its pozzolanic property after used as dye-adsorbent

    Directory of Open Access Journals (Sweden)

    Penpolcharoen, M.

    2004-02-01

    Full Text Available Bituminous fly ash, which is an industrial waste, was used as an adsorbent to remove dyestuff from the textile-dye wastewater. The batch kinetic and isotherm experiments of the synthetic wastewater were firstly conducted to determine the adsorption behavior and optimal conditions for adsorption. The optimal conditions were then applied to the actual textile-dye wastewater. Under the original conditions of fly ash and wastewater, the results indicated that the color could be removed up to 86.65% by 12 g of the fly ash /L of the wastewater within 30 min. Its adsorption was described by the Freundlich isotherm. The dye-adsorbed fly ash was further studied on its pozzolanic property in terms of compressive strength by using it as a partial substitute to Portland cement type I to produce mortar. The result revealed that the highest compressive strength was of the sample containing 10% by weight of the dye-adsorbed fly ash in replacement of cement. It possessed 215 kg/cm2 at 28 days, which is 92.67% of the sample containing 10% by weight of the original fly ash in replacement of cement, or 83.33 of the cement mortar. For the environmental concern, leachabilities of lead (Pb, chromium (Cr, copper (Cu and zinc (Zn from all mortars were also carried out. No leaching of the heavy metals from any samples could be detected. Hence, the dye-adsorbed fly ash can be used as an environmental friendly construction material.

  2. Nuclear method for determination of asphalt content corrected for moisture in bituminous mixture. Final report, March 1988-February 1989

    International Nuclear Information System (INIS)

    This report presents results of research on the development of a method for determination of asphalt content corrected for moisture using the nuclear-gauge method. The researchers selected an approach that involved rapid drying of the asphalt concrete samples in a microwave oven prior to the determination of asphalt content using a Troxler Model 3241-C nuclear asphalt-content gauge. As a reference, asphalt contents were also measured using quantitative extraction. In general, good agreement was found between asphalt contents measured by the Troxler Model 3241-C nuclear gauge and asphalt contents measured by quantitative extraction. In extended sampling for Plant 1, no significant increase in nuclear gauge error was seen over a 10-day sampling period, which indicates that daily calibration of the nuclear gauge is probably unnecessary to maintain satisfactory performance. The field demonstration of the procedure of drying the bituminous mixture in a microwave oven and then determining its asphalt content by the nuclear method indicated asphalt-content results were obtained approximately 1 hour faster than results obtained by quantitative extraction

  3. JV Task-123 Determination of Trace Element Concentrations at an Eastern Bituminous Coal Plant Employing an SCR and Wet FGD

    Energy Technology Data Exchange (ETDEWEB)

    Dennis Laudal

    2008-05-01

    The Energy & Environmental Research Center (EERC), in partnership with Babcock & Wilcox (B&W) and with funding from U.S. Department of Energy (DOE), conducting tests to prove that a high level of mercury control (>90%) can be achieved at a power plant burning a high-sulfur eastern bituminous coal. With funding from the Electric Power Research Institute (EPRI), DOE, and Center for Air Toxic Metals{reg_sign} (CATM{reg_sign}) Affiliates Program, the EERC completed an additional sampling project to provide data as to the behavior of a number of trace elements across the various pollution control devices, with a special emphasis on the wet flue gas desulfurization (FGD) system. Results showed that the concentrations of almost all the elements of interest leaving the stack were very low, and a high percentage of the trace elements were captured in the electrostatic precipitator (ESP) (for most, >80%). Although, with a few exceptions, the overall mass balances were generally quite good, the mass balances across the wet FGD were more variable. This is most likely a result of some of the concentrations being very low and also the uncertainties in determining flows within a wet FGD.

  4. Effect of asphaltene and resin oils on the viscosity of bituminous petroleum materials to be used as asphalt primers

    Directory of Open Access Journals (Sweden)

    Bencomo, M. R.

    2006-03-01

    Full Text Available The bituminous crude from the Machete, Venezuela, area, which has such a fluid consistency that it falls outside the normal scope of the A5TM D-5 (1 penetration test exceeding the 3D-mm ceiling specified in that standard and can be used as an asphalt primer: Like other asphalt products, these materials are -chemically speaking- a mix of numerous naphthenic, paraffinic and aromatic hydrocarbons and heterocyclic compounds containing sulphur, nitrogen, oxygen and so on. They have a dense and a malthene oil phase which, along with the natural hydrocarbons additives used in these products acts as a volatile fluidizer. The former is described as a mix of asphaltenes: complex high molecular weight substances that are insoluble in paraffinic hydrocarbons and soluble in aromatic compounds such as benzene. The malthene oil phase, in turn, consists in a mix of resins and hydrocarbons and together the two constitute a colloidal system. The experiments discussed in the present paper were conducted to determine the effect of the proportion of asphaltenes and resin oils on the viscosity of such bituminous crude emulsions/ with a view to their use as primers. These experiments were run in a Parr batch reactor in a nitrogen atmosphere using n-heptane as a solvent. The resins were separated after the asphaltenes precipitated from the samples and subsequently from the malthene fraction obtained. The results showed that the asphaltenes account for the structural characteristics and consistency of the medium and the resin oils for its cohesive properties/,the malthene oils act as solvents.Los crudos extrapesados procedentes del área Machete (Venezuela son materiales de consistencia blanda o fluida, por lo que se salen del campo en el que normalmente se aplica el ensayo de penetración a productos asfálticos según el método ASTM D-5 (1, cuyo límite máximo es 30 mm, y pueden ser utilizados como pinturas asfálticas de imprimación. Al igual que otros productos

  5. Functional group and individual maceral chemistry of high volatile bituminous coals from southern Indiana: Controls on coking

    Science.gov (United States)

    Walker, R.; Mastalerz, Maria

    2004-01-01

    The individual maceral chemistries of two Pennsylvanian, high volatile bituminous coals, the Danville Coal Member (Dugger Formation, R o=0.55%) and the Lower Block Coal Member (Brazil Formation, R o=0.56%) of Indiana, were investigated using electron microprobe and Fourier Transform Infrared Spectrometry (FTIR) techniques, with the purpose of understanding differences in their coking behavior. Microprobe results reveal that carbon contents are highest in inertinite and sporinite, followed by desmocollinite and telocollinite. Oxygen and organic nitrogen are most abundant in telocollinite and desmocollinite; sporinite and inertinite contain lesser amounts of these two elements. Organic sulfur contents are highest in sporinite, lowest in inertinite, and intermediate in desmocollinite and telocollinite. Vitrinites within the Danville and Lower Block coals are very similar in elemental composition, while Lower Block inertinites and sporinites have higher carbon, lower oxygen, and sulfur contents which, when combined with the inertinite-and sporinite-rich composition of the Lower Block seam, strongly influences its whole coal chemistry. Fourier transform infrared spectrometry revealed greater aromatic hydrogen in the Lower Block coal, along with higher CH2/CH3 ratios, which suggest that liptinites contribute considerable amounts of long-chain, unbranched aliphatics to the overall kerogen composition of the Lower Block coal. Long-chain, unbranched aliphatics crack at higher temperatures, producing tar and oily byproducts during coking; these may help increase Lower Block plasticity. Electron microprobe and FTIR results indicate that individual maceral chemistries, combined with the maceral composition of the seam, are the primary control of better coking properties of the Lower Block coal. ?? 2003 Elsevier B.V. All rights reserved.

  6. Processes related to the water uptake by EUROBITUM bituminized radioactive waste: Theoretical considerations and first experimental results

    International Nuclear Information System (INIS)

    According to the present Belgian radioactive waste management program, EUROBITUM bituminized radioactive waste will be disposed of in a geologically stable underground clay formation. The Boom Clay is studied as a potential host formation because of its low diffusion and high retention properties towards radionuclides. The presence of the radioactive waste should not disturb these properties. Due to the presence of hygroscopic salts (25 to 30 weight% NaNO3), EUROBITUM will take up pore water which will result in a swelling and possibly in a very high swelling pressure. First scoping calculations suggest that the swelling pressure exerted to Boom Clay should remain below 7 to 8 MPa to avoid the formation of fractures. If the bitumen in EUROBITUM behaved like a perfect semi-permeable membrane and if no swelling were allowed after the dissolution of NaNO3 into a saturated solution of 10.8 M, osmotic pressures of ∼50 MPa could be attained. To better understand the interaction between the swelling EUROBITUM and the host formation, coupled hydro-chemical-mechanical constitutive laws for EUROBITUM have to be developed. To this purpose, water uptake tests under constant volume ('confined') and constant stress ('semi-confined') conditions are being performed. After ∼2 years of hydration of small inactive EUROBITUM samples in constant volume conditions, the swelling pressure has raised to ∼12 MPa. The volume of samples that can swell against counter pressures of 2.2, 3.3, or 4.4 MPa (constant stress tests) increased with ∼5 to 11 volume%, independently of the applied counter pressure. Approximately 10 weight% of the initial NaNO3 content has been leached. (authors)

  7. Radioactivity concentrations and dose assessment for bitumen and soil samples around a bituminous deposit in Ondo State, Nigeria

    International Nuclear Information System (INIS)

    Bitumen samples and soil samples around a bituminous deposit in Ondo State, Nigeria, were analysed for 40K, 226Ra and 232Th employing gamma-ray spectrometry. The activity concentrations of 40K, 226Ra and 232Th in soil varied from (45.2 ± 5.3) to (484.2 ± 25.9), BDL (below detectable limit) to (27.7 ± 2.1) and (22.8 ± 2.7) to (62.4 ± 6.8) Bq.kg-1, respectively. The corresponding mean values were (240.2 ± 133.5), (13.3 ± 8.0) and (40.0 ± 10.2) Bq.kg-1, respectively. The mean activity concentrations of the radionuclides in the bitumen were (58.4 ± 36.4), (16.1 ± 13.3) and (32.5 ± 13.1) Bq.kg-1, respectively, for 40K, 226Ra and 232Th. The mean absorbed dose and effective dose for the soil samples were (41.5 ± 8.9) nGy.h-1 and (50.7 ± 10.9) μSv.y-1, respectively, while those of the bitumen samples were (29.5 ± 15.6) nGy.h-1 and (36.1 ± 19.1) μSv.y-1, respectively. For radiological hazard assessment, the radium equivalent activity and the external hazard index were determined. The values of the radium equivalent activity and external hazard index obtained for the soil and bitumen samples were lower than the recommended limit. (authors)

  8. Computational micromechanical analysis of the representative volume element of bituminous composite materials

    Science.gov (United States)

    Ozer, Hasan; Ghauch, Ziad G.; Dhasmana, Heena; Al-Qadi, Imad L.

    2016-08-01

    Micromechanical computational modeling is used in this study to determine the smallest domain, or Representative Volume Element (RVE), that can be used to characterize the effective properties of composite materials such as Asphalt Concrete (AC). Computational Finite Element (FE) micromechanical modeling was coupled with digital image analysis of surface scans of AC specimens. Three mixtures with varying Nominal Maximum Aggregate Size (NMAS) of 4.75 mm, 12.5 mm, and 25 mm, were prepared for digital image analysis and computational micromechanical modeling. The effects of window size and phase modulus mismatch on the apparent viscoelastic response of the composite were numerically examined. A good agreement was observed in the RVE size predictions based on micromechanical computational modeling and image analysis. Micromechanical results indicated that a degradation in the matrix stiffness increases the corresponding RVE size. Statistical homogeneity was observed for window sizes equal to two to three times the NMAS. A model was presented for relating the degree of statistical homogeneity associated with each window size for materials with varying inclusion dimensions.

  9. Mapping and prediction of Coal Workers' Pneumoconiosis with bioavailable iron content in the bituminous coals

    Science.gov (United States)

    Huang, X.; Li, W.; Attfield, M.D.; Nadas, A.; Frenkel, K.; Finkelman, R.B.

    2005-01-01

    Based on the first National Study of Coal Workers' Pneumoconiosis (CWP) and the U.S. Geological Survey database of coal quality, we show that the prevalence of CWP in seven coal mine regions correlates with levels of bioavailable iron (BAI) in the coals from that particular region (correlation coefficient r = 0.94, p < 0.0015). CWP prevalence is also correlated with contents of pyritic sulfur (r = 0.91, p < 0.0048) or total iron (r = 0.85, p < 0.016) but not with coal rank (r = 0.59, p < 0.16) or silica (r = 0.28, p < 0.54). BAI was calculated using our model, taking into account chemical interactions of pyrite, sulfuric acid, calcite, and total iron. That is, iron present in coals can become bioavailable by pyrite oxidation, which produces ferrous sulfate and sulfuric acid. Calcite is the major component in coals that neutralizes the available acid and inhibits iron's bioavailabiity. Therefore, levels of BAI in the coals are determined by the available amounts of acid after neutralization of calcite and the amount of total iron in the coals. Using the linear fit of CWP prevalence and the calculated BAI in the seven coal mine regions, we have derived and mapped the pneumoconiotic potencies of 7,000 coal samples. Our studies indicate that levels of BAI in the coals may be used to predict coal's toxicity, even before large-scalen mining.

  10. Evolution of rheological properties of nuclear bituminized waste products, towards an ageing/viscosity law

    International Nuclear Information System (INIS)

    This work is a contribution to the understanding of rheological properties of bitumen and their evolution under gamma irradiation. The prediction of swelling ratio is necessary to evaluate the state of the containers, particularly during the reversibility phase of the storage. The objective of this work is thus to establish the rheological data its evolution under irradiation in order to predict the container swelling with time. After the rheological and thermal characterization of pure bitumen, a series of extrusion trials has been carried out. The state of dispersion essentially depends on the ratio N/Q (screw speed to feed rate). Extreme values of N/Q show the highest yield stress, indicating an improved dispersion state. The industrial bitumen compound exhibits the highest viscosity compared to model compounds, which limits bubble migration. Finally, the effect of gamma irradiation on pure bitumen and compounds behaviour has been studied. External and structural modifications have been evidenced. A theoretical model based on Krieger-Dougherty equation has been developed and shows a good agreement with experimental data. (author)

  11. Petroleum Generation Potential of Bituminous Mudstones in Tomsk Region Bazhen Suite (Western Siberia)

    International Nuclear Information System (INIS)

    The article reviews the prognosis for Bazhen suite HC generation potential in order to select primary commercially exploitable areas. A map of generation potential density for Bazhen suite passive reserves has been plotted. It is based on published papers on calculation of organic carbon concentration using the data of exploration and prospect well gamma-ray logging. The deliverables are compared with geochemical core examination results. Lithological heterogeneity of deposits underlying the Bazhen suite is systemized in order to estimate the possible decrease of the suite generation potential due to hydrocarbon migration to underlying deposits. Three types of cross-sections are distinguished - predominately sandy, alternating silt-argillous and argillous. An estimate of the proportion of Bazhen suite generation potential required for the discovered hydrocarbon deposit formation within oilgathering fields of the first (sandy) type thoroughly explored by deep-hole drilling was carried out. Both quantitative (types 1, 3) and qualitative (type 2) estimations of decrease of the initial generation potential density are carried out for the above-mentioned types. Taking into account the specific character of shale oil development, a further work is required in order to design for each type its individual set of shale strata operating conditions

  12. Adsorption of SO2 on bituminous coal char and activated carbon fiber

    Science.gov (United States)

    DeBarr, J.A.; Lizzio, A.A.; Daley, M.A.

    1997-01-01

    The SO2 adsorption behaviors of activated carbons produced from Illinois coal and of commercially prepared activated carbon fibers (ACFs) were compared. There was no relation between surface area of coal-based carbons and SO2 adsorption, whereas adsorption of SO2 on the series of ACFs was inversely proportional to N2 BET surface area. Higher surface area ACFs had wider pores and adsorbed less SO2; thus, pore size distribution is thought to play a significant role in SO2 adsorption for these materials. Oxidation with HNO3 and/or H2SO4, followed by heat treatment at 700-925 ??C to remove carbon-oxygen complexes, resulted in increased SO2 adsorption for both coal chars and ACFs. This behavior was explained by an increase in the available number of free sites, previously occupied by oxygen and now available for SO2 adsorption. The use of nitrogen-containing functional groups on ACFs of proper pore size shows promise for further increasing SO2 adsorption capacities. Knowledge of the relationship among the number of free sites, pore size, and surface chemistry on corresponding SO2 adsorption should lead to the development of more efficient adsorbents prepared from either coal or ACFs.

  13. On the oxidation of the dissolved organic matter in Boom clay by NaNO3 and NaNO2 from disposed Eurobitum bituminized waste

    International Nuclear Information System (INIS)

    Document available in extended abstract form only. In Belgium, Boom Clay is studied as a potential host clay formation for the final disposal of EUROBITUM bituminized waste, which consists of 60 wt% hard bitumen (Mexphalt R85/40) and 40 wt% waste. The main salts that are present in the bituminized waste are NaNO3, 20-30 wt%, and CaSO4, 4-6 wt%. After disposal of the waste in the clay, an uptake of pore water by the embedded, dehydrated and hygroscopic salts will lead to a swelling of the waste and to a release of the salts into the Boom Clay. A possible consequence of the salt release is the oxidation of the clay by nitrate and, possibly, nitrite, resulting in a lower reducing capacity of the clay towards redox sensitive radionuclides, which in turn could have an impact on the migration behaviour of these radionuclides. The extent of oxidation of authigenic Boom Clay redox sensitive components, like organic matter and pyrite is studied at the SCK.CEN. As a first step in the study of the influence of nitrate and nitrite on the redoxactive Boom Clay components, we performed batch tests with dissolved organic matter (DOM). DOM was exposed to different concentrations of nitrate and nitrite for more than one year in both biotic and abiotic conditions. This paper will discuss the results obtained by exposing DOM to nitrate and nitrite and comparing two methods for the determination of its redox capacity. NaNO3 or NaNO2, previously stored under inert atmosphere to remove all oxygen gas, was added to Boom Clay water collected from a piezometer to obtain final salt concentrations of 0.1 and 0.005 M NaNO3, or 0.05 and 0.005 M NaNO2. Sodium azide, also stored under inert atmosphere, was added (0.2 wt. %) to inhibit the microbial activity in the tests, creating abiotic conditions. All solutions were prepared in an anaerobic glove box. The nitrate and nitrite reduction by DOM was followed by analysing the concentrations of nitrate, nitrite and ammonium in the solutions and of

  14. Detection of rare earth elements in Powder River Basin sub-bituminous coal ash using laser-induced breakdown spectroscopy (LIBS)

    Energy Technology Data Exchange (ETDEWEB)

    Tran, Phuoc [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United State; Mcintyre, Dustin [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United State

    2015-10-01

    We reported our preliminary results on the use of laser-induced breakdown spectroscopy to analyze the rare earth elements contained in ash samples from Powder River Basin sub-bituminous coal (PRB-coal). We have identified many elements in the lanthanide series (cerium, europium, holmium, lanthanum, lutetium, praseodymium, promethium, samarium, terbium, ytterbium) and some elements in the actinide series (actinium, thorium, uranium, plutonium, berkelium, californium) in the ash samples. In addition, various metals were also seen to present in the ash samples

  15. Disposal of bituminized and other low- and medium-level wastes: Waste characterization and the retention of migrating radionuclides by steel corrosion products

    Science.gov (United States)

    Biegalski, Kendra Mylene Foltz

    1998-09-01

    The validity of using scaling factors with the reference nuclide, sp{137}Cs, for activity determinations of sp{238}Pu, sp{239,\\ 240}Pu, and sp{241}Am in low- and medium-level bituminized and unconditioned evaporator concentrates (ECs) produced at Riso National Laboratory (RNL), Denmark was investigated. The presence of constant activity ratios between sp{137}Cs and the Pu isotopes above was predicted because a large part of this waste stream originated from research on irradiated light water reactor fuel. Activity ratios were measured in different waste samples by comparison of gamma-measurements to results from destructive analyses using alpha-spectrometry. Results were verified using activity ratios of spent low-enriched fuel from the literature. Continuation studies on the mechanisms influencing releases from bituminized low- and medium-level wastes were performed by leach tests on samples of various compositions and exposed to diverse environments. Four compositions of bituminized materials were studied including (1) bitumen with NaNOsb3 and BaSOsb4, (2) bitumen with NaNOsb3, BaSOsb4, and Nisb2Fe(CN)sb6, (3) bitumen with NaNOsb3, BaSOsb4, Nisb2Fe(CN)sb6, and K-soap, and (4) bituminized RNL ECs. Leachant solutions used included (1) filtered deionized water, (2) 0.001-N KOH, (3) 0.01-N KOH, and (4) 0.001-N Ca(OH)sb2. One trial was exposed to high-humidity air while two others had a cement disk suspended in the leachant. Some of the resulting data was used for the on-going validation of the SWL (Swelling, Water uptake, and Leaching) code created at RNL. To improve the accuracy of projected releases from radioactive waste disposal systems, the sorption characteristics of steel corrosion products were investigated with a special emphasis on competitive sorption between Sr and Na. The corrosion rate of steel exposed to various environments was studied qualitatively and, with some systems, quantitatively. Traditional and non-traditional adsorption

  16. Progressive oxidation of pyrite in five bituminous coal samples: An As XANES and 57Fe Moessbauer spectroscopic study

    International Nuclear Information System (INIS)

    Naturally occurring pyrite commonly contains minor substituted metals and metalloids (As, Se, Hg, Cu, Ni, etc.) that can be released to the environment as a result of its weathering. Arsenic, often the most abundant minor constituent in pyrite, is a sensitive monitor of progressive pyrite oxidation in coal. To test the effect of pyrite composition and environmental parameters on the rate and extent of pyrite oxidation in coal, splits of five bituminous coal samples having differing amounts of pyrite and extents of As substitution in the pyrite, were exposed to a range of simulated weathering conditions over a period of 17 months. Samples investigated include a Springfield coal from Indiana (whole coal pyritic S = 2.13 wt.%; As in pyrite = detection limit (d.l.) to 0.06 wt.%), two Pittsburgh coal samples from West Virginia (pyritic S = 1.32-1.58 wt.%; As in pyrite = d.l. to 0.34 wt.%), and two samples from the Warrior Basin, Alabama (pyritic S = 0.26-0.27 wt.%; As in pyrite = d.l. to 2.72 wt.%). Samples were collected from active mine faces, and expected differences in the concentration of As in pyrite were confirmed by electron microprobe analysis. Experimental weathering conditions in test chambers were maintained as follows: (1) dry Ar atmosphere; (2) dry O2 atmosphere; (3) room atmosphere (relative humidity ∼20-60%); and (4) room atmosphere with samples wetted periodically with double-distilled water. Sample splits were removed after one month, nine months, and 17 months to monitor the extent of As and Fe oxidation using As X-ray absorption near-edge structure (XANES) spectroscopy and 57Fe Moessbauer spectroscopy, respectively. Arsenic XANES spectroscopy shows progressive oxidation of pyritic As to arsenate, with wetted samples showing the most rapid oxidation. 57Fe Moessbauer spectroscopy also shows a much greater proportion of Fe3+ forms (jarosite, Fe3+ sulfate, FeOOH) for samples stored under wet conditions, but much less difference among samples stored

  17. Osmosis-induced water uptake by Eurobitum bituminized radioactive waste and pressure development in constant volume conditions

    Energy Technology Data Exchange (ETDEWEB)

    Marieen, A., E-mail: amarien@sckcen.be [Waste and Disposal Expert Group, Belgian Nuclear Research Centre (SCK-CEN), Boeretang 200, 2400 Mol (Belgium); Mokni, N., E-mail: Nadia.mokni@upc.edu [Department of Geotechnical Engineering and Geosciences, Universidad Politecnica de Catalunya (UPC), Calle Gran Capitan, s/n, Edificio C-1, 08034 Barcelona (Spain); Valcke, E. [Waste and Disposal Expert Group, Belgian Nuclear Research Centre (SCK-CEN), Boeretang 200, 2400 Mol (Belgium); Olivella, S. [Department of Geotechnical Engineering and Geosciences, Universidad Politecnica de Catalunya (UPC), Calle Gran Capitan, s/n, Edificio C-1, 08034 Barcelona (Spain); Smets, S. [Waste and Disposal Expert Group, Belgian Nuclear Research Centre (SCK-CEN), Boeretang 200, 2400 Mol (Belgium); Li, X., E-mail: xli@sckcen.be [EIG EURIDICE, Boeretang 200, 2400 Mol (Belgium)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer The water uptake by Eurobitum is studied to judge the safety of geological disposal. Black-Right-Pointing-Pointer High pressures of up to 20 MPa are measured in constant volume water uptake tests. Black-Right-Pointing-Pointer The morphology of leached Eurobitum samples is studied with {mu}CT and ESEM. Black-Right-Pointing-Pointer The observations are reproduced by an existing CHM formulation for Eurobitum. - Abstract: The chemo-hydro-mechanical (CHM) interaction between swelling Eurobitum radioactive bituminized waste (BW) and Boom Clay is investigated to assess the feasibility of geological disposal for the long-term management of this waste. These so-called compatibility studies include laboratory water uptake tests at Belgian Nuclear Research Center SCK-CEN, and the development of a coupled CHM formulation for Eurobitum by the International Center for Numerical Methods and Engineering (CIMNE, Polytechnical University of Cataluna, Spain). In the water uptake tests, the osmosis-induced swelling, pressure increase and NaNO{sub 3} leaching of small cylindrical BW samples (diameter 38 mm, height 10 mm) is studied under constant total stress conditions and nearly constant volume conditions; the actual geological disposal conditions should be intermediate between these extremes. Two nearly constant volume tests were stopped after 1036 and 1555 days to characterize the morphology of the hydrated BW samples and to visualize the hydrated part with microfocus X-ray Computer Tomography ({mu}CT) and Environmental Scanning Electron Microscopy (ESEM). In parallel, a coupled CHM formulation is developed that describes chemically and hydraulically coupled flow processes in porous materials with salt crystals, and that incorporates a porosity dependent membrane efficiency, permeability and diffusivity. When Eurobitum BW is hydrated in (nearly) constant volume conditions, the osmosis-induced water uptake results in an increasing pressure to

  18. Dike intrusions into bituminous coal, Illinois Basin: H, C, N, O isotopic responses to rapid and brief heating

    Science.gov (United States)

    Schimmelmann, A.; Mastalerz, Maria; Gao, L.; Sauer, P.E.; Topalov, K.

    2009-01-01

    Unlike long-term heating in subsiding sedimentary basins, the near-instantaneous thermal maturation of sedimentary organic matter near magmatic intrusions is comparable to artificial thermal maturation in the laboratory in terms of short duration and limited extent. This study investigates chemical and H, C, N, O isotopic changes in high volatile bituminous coal near two Illinois dike contacts and compares observed patterns and trends with data from other published studies and from artificial maturation experiments. Our study pioneers in quantifying isotopically exchangeable hydrogen and measuring the D/H (i.e., 2H/1H) ratio of isotopically non-exchangeable organic hydrogen in kerogen near magmatic contacts. Thermal stress in coal caused a reduction of isotopically exchangeable hydrogen in kerogen from 5% to 6% in unaltered coal to 2-3% at contacts, mostly due to elimination of functional groups (e.g., {single bond}OH, {single bond}COOH, {single bond}NH2). In contrast to all previously published data on D/H in thermally matured organic matter, the more mature kerogen near the two dike contacts is D-depleted, which is attributed to (i) thermal elimination of D-enriched functional groups, and (ii) thermal drying of hydrologically isolated coal prior to the onset of cracking reactions, thereby precluding D-transfer from relatively D-enriched water into kerogen. Maxima in organic nitrogen concentration and in the atomic N/C ratio of kerogen at a distance of ???2.5 to ???3.5 m from the thicker dike indicate that reactive N-compounds had been pyrolytically liberated at high temperature closer to the contact, migrated through the coal seam, and recombined with coal kerogen in a zone of lower temperature. The same principle extends to organic carbon, because a strong ??13Ckerogen vs. ??15Nkerogen correlation across 5.5 m of coal adjacent to the thicker dike indicates that coal was functioning as a flow-through reactor along a dynamic thermal gradient facilitating back

  19. Osmosis-induced water uptake by Eurobitum bituminized radioactive waste and pressure development in constant volume conditions

    Science.gov (United States)

    Mariën, A.; Mokni, N.; Valcke, E.; Olivella, S.; Smets, S.; Li, X.

    2013-01-01

    The chemo-hydro-mechanical (CHM) interaction between swelling Eurobitum radioactive bituminized waste (BW) and Boom Clay is investigated to assess the feasibility of geological disposal for the long-term management of this waste. These so-called compatibility studies include laboratory water uptake tests at the Belgian Nuclear Research Center SCK•CEN, and the development of a coupled CHM formulation for Eurobitum by the International Center for Numerical Methods and Engineering (CIMNE, Polytechnical University of Cataluña, Spain). In the water uptake tests, the osmosis-induced swelling, pressure increase and NaNO3 leaching of small cylindrical BW samples (diameter 38 mm, height 10 mm) is studied under constant total stress conditions and nearly constant volume conditions; the actual geological disposal conditions should be intermediate between these extremes. Two nearly constant volume tests were stopped after 1036 and 1555 days to characterize the morphology of the hydrated BW samples and to visualize the hydrated part with microfocus X-ray Computer Tomography (μCT) and Environmental Scanning Electron Microscopy (ESEM). In parallel, a coupled CHM formulation is developed that describes chemically and hydraulically coupled flow processes in porous materials with salt crystals, and that incorporates a porosity dependent membrane efficiency, permeability and diffusivity. When Eurobitum BW is hydrated in (nearly) constant volume conditions, the osmosis-induced water uptake results in an increasing pressure to values that can be (in theory) as high as 42.8 MPa, being the osmotic pressure of a saturated NaNO3 solution. After about four years of hydration in nearly constant volume water uptake tests, pressures up to 20 MPa are measured. During this hydration period only the outer layers with a thickness of 1-2 mm were hydrated (as derived from μCT and ESEM analyses), and only about 10-20% of the initial NaNO3 content was released by the samples. In the studied test

  20. Dike intrusions into bituminous coal, Illinois Basin: H, C, N, O isotopic responses to rapid and brief heating

    Science.gov (United States)

    Schimmelmann, Arndt; Mastalerz, Maria; Gao, Ling; Sauer, Peter E.; Topalov, Katarina

    2009-10-01

    Unlike long-term heating in subsiding sedimentary basins, the near-instantaneous thermal maturation of sedimentary organic matter near magmatic intrusions is comparable to artificial thermal maturation in the laboratory in terms of short duration and limited extent. This study investigates chemical and H, C, N, O isotopic changes in high volatile bituminous coal near two Illinois dike contacts and compares observed patterns and trends with data from other published studies and from artificial maturation experiments. Our study pioneers in quantifying isotopically exchangeable hydrogen and measuring the D/H (i.e., 2H/ 1H) ratio of isotopically non-exchangeable organic hydrogen in kerogen near magmatic contacts. Thermal stress in coal caused a reduction of isotopically exchangeable hydrogen in kerogen from 5% to 6% in unaltered coal to 2-3% at contacts, mostly due to elimination of functional groups (e.g., sbnd OH, sbnd COOH, sbnd NH 2). In contrast to all previously published data on D/H in thermally matured organic matter, the more mature kerogen near the two dike contacts is D-depleted, which is attributed to (i) thermal elimination of D-enriched functional groups, and (ii) thermal drying of hydrologically isolated coal prior to the onset of cracking reactions, thereby precluding D-transfer from relatively D-enriched water into kerogen. Maxima in organic nitrogen concentration and in the atomic N/C ratio of kerogen at a distance of ˜2.5 to ˜3.5 m from the thicker dike indicate that reactive N-compounds had been pyrolytically liberated at high temperature closer to the contact, migrated through the coal seam, and recombined with coal kerogen in a zone of lower temperature. The same principle extends to organic carbon, because a strong δ13C kerogen vs. δ15N kerogen correlation across 5.5 m of coal adjacent to the thicker dike indicates that coal was functioning as a flow-through reactor along a dynamic thermal gradient facilitating back-reactions between mobile

  1. Spanish Round Robin test on water sensitivity test of bituminous mixtures; Ejercicio espanol interlaboratorios sobre el ensayo de sensibilidad al gua de mezclas bituminosas

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez Saez, R.; Enrique Gabeiras, L.; Miranda Perez, L.; Valor Hernandez, F.

    2011-07-01

    The amendment of Article 542 and 543 on the hot asphalt mixtures included in the Spanish Technical specifications for Road Construction (PG-3), by Circular Order 24/2008, introduced a new series of modification to adapt Spanish regulations to European standards series EN 13108. Among the various amendments, new tests methods and design criteria are considered, as UNE-EN 12697-12 for assessing the water sensitivity on compacted specimens, which is mandatory for every kind of bituminous mixture. In this paper, firstly a comparison between the European method and the old Spanish method described in the NLT-162 is made, explaining the experimental conditions selected. The results of an interlaboratory study or Round Robin Test conducted in ten Spanish laboratories are subsequently described and analyzed, in order to allow each laboratory to assess its technical performance, and also to determine quantitatively the precision of the new method in terms of repeatability and reproducibility. (Author) 15 refs.

  2. Mercury emissions during cofiring of sub-bituminous coal and biomass (chicken waste, wood, coffee residue, and tobacco stalk) in a laboratory-scale fluidized bed combustor

    Energy Technology Data Exchange (ETDEWEB)

    Yan Cao; Hongcang Zhou; Junjie Fan; Houyin Zhao; Tuo Zhou; Pauline Hack; Chia-Chun Chan; Jian-Chang Liou; Wei-ping Pan [Western Kentucky University (WKU), Bowling Green, KY (USA). Institute for Combustion Science and Environmental Technology (ICSET)

    2008-12-15

    Four types of biomass (chicken waste, wood pellets, coffee residue, and tobacco stalks) were cofired at 30 wt % with a U.S. sub-bituminous coal (Powder River Basin Coal) in a laboratory-scale fluidized bed combustor. A cyclone, followed by a quartz filter, was used for fly ash removal during tests. The temperatures of the cyclone and filter were controlled at 250 and 150{sup o}C, respectively. Mercury speciation and emissions during cofiring were investigated using a semicontinuous mercury monitor, which was certified using ASTM standard Ontario Hydra Method. Test results indicated mercury emissions were strongly correlative to the gaseous chlorine concentrations, but not necessarily correlative to the chlorine contents in cofiring fuels. Mercury emissions could be reduced by 35% during firing of sub-bituminous coal using only a quartz filter. Cofiring high-chlorine fuel, such as chicken waste (Cl = 22340 wppm), could largely reduce mercury emissions by over 80%. When low-chlorine biomass, such as wood pellets (Cl = 132 wppm) and coffee residue (Cl = 134 wppm), is cofired, mercury emissions could only be reduced by about 50%. Cofiring tobacco stalks with higher chlorine content (Cl = 4237 wppm) did not significantly reduce mercury emissions. Gaseous speciated mercury in flue gas after a quartz filter indicated the occurrence of about 50% of total gaseous mercury to be the elemental mercury for cofiring chicken waste, but occurrence of above 90% of the elemental mercury for all other cases. Both the higher content of alkali metal oxides or alkali earth metal oxides in tested biomass and the occurrence of temperatures lower than 650{sup o}C in the upper part of the fluidized bed combustor seemed to be responsible for the reduction of gaseous chlorine and, consequently, limited mercury emissions reduction during cofiring. 36 refs., 3 figs. 1 tab.

  3. 纤维沥青混合料的拌和成型工艺研究%Research on Mixing and Shaping Technology of Fiber Bituminous Mixture

    Institute of Scientific and Technical Information of China (English)

    程英伟; 何晓鸣

    2012-01-01

    利用正交试验对剑麻纤维沥青混凝土混合料的拌和成型工艺进行研究.在固定配合比的前题下,以拌和方案、沥青加热温度、集料加热温度和成型温度为试验因素,模拟路面施工的各种拌和成型情况设计了L9正交表分别进行马歇尔试验.运用极差分析法对试验结果进行分析,确定了纤维沥青混合料拌和成型的优选方案为“同步法拌和+沥青加热温度为175℃+集料加热温度为206℃+成型温度为165℃”.最后分析了几种试验因素对试验指标的影响机理.%In this paper, mixing and shaping technology of bituminous concrete mixture with sisal fiber is researched by orthogonal experiment. Under a fixed mix proportion, mixing solutions, asphalt heating temperature, aggregate heating temperature and shaping temperature are selected as test factors. The variety of mixing and shaping in pavement construction is simulated by designing a L9 orthogonal table for Marshall tests. Range Analysis Method is used to analyze test results, and then the optimal scheme of mixing and shaping for fiber bituminous concrete mixture is determined. The optimal scheme is "synchronization method of mixing+asphalt heating temperature of 175℃+aggregate heating temperature of 206℃ + shaping temperature of 165℃”. Last, the influence mechanism of test factors on test indicators is analyzed.

  4. 基于热重分析法的烟煤掺烧褐煤特性研究%Combustion Characteristics of Bituminous Coal Blended with Lignite Using Thermo-gravimetric Method

    Institute of Scientific and Technical Information of China (English)

    杨志斌; 马莹; 戴新; 赵建军; 关彦军; 张锴

    2015-01-01

    针对电厂掺烧褐煤缺乏相关理论指导的技术需求,采用热重分析方法系统考察了包煤、准煤和褐煤的单独燃烧特性,并将两种烟煤分别以10%、30%、50%和70%的比例在相同条件下与褐煤混合燃烧,根据各燃料燃烧特征参数计算了单一煤种及其不同掺混比例的着火指数、燃尽指数和综合燃烧指数。结果表明,褐煤最易着火和燃尽;包煤着火特性较好,但在550~660℃范围内出现难燃峰致使燃尽特性变差;准煤的着火特性最差,燃尽特性略优于包煤;将包煤和准煤与褐煤掺混后燃烧特性有所改善,各燃烧特征温度降低,且综合燃烧指数随褐煤掺烧比例的增加而增加。建议在电厂实际应用时,褐煤的掺烧比例控制在30%-50%之间。%Based on the actual requirement for fundamental theory of blending lignite in coal-fired power stations, combustion characteristics of lignite, bituminous coal and their blends were investigated by using thermogravimetric method ( TGA) in this paper.Lignite was blended with two types of bituminous coals in proportions of 10%, 30%, 50%and 70%, respectively.The ignition index, burnout index and comprehensive combustion index of single and mixed fuels were calculated by means of combustion characteristic parameters.The results show that lig-nite displays the best ignition and burnout performace, Bao coal is easier to ignite but hard to burn out in the tem-perature range of 550 and 660℃.Compared to Bao coal, Zhun coal is the hardest to ignite but better to burn out. The performance of combustion can be improved after blending lignite, which is largely because the comprehensive combustion index of blended coals increases with the increasing ratio of lignite.Therefore, the blending ratio of lig-nite suggested lignite ration should be controlled between 30%and 50%.

  5. Thermo-mechanical behavior of bituminous mixtures at low temperatures. Links between the binder characteristics and the mix properties; Comportement thermomecanique des enrobes bitumeux a basses temperatures: relations entre les proprietes du liant et de l'enrobe

    Energy Technology Data Exchange (ETDEWEB)

    Olard, F.

    2003-10-01

    This thesis has been realized within the framework of a partnership between the Ecole Nationale des TPE, APPIA and EUROVIA. The company Total has also been associated to this project. The study deals with the thermo-mechanical behavior of bituminous materials at low temperatures. The aim is to establish the links between the characteristics of the binder and the properties of bituminous mixes at low temperatures, and to better understand the existing low-temperature parameters and criteria for binders (or to propose new ones), related to the in-situ behavior of bituminous mixtures. A large experimental campaign has been carried out so as to fulfill this goal. After a bibliographical study on the rheology and the thermo-mechanical properties of (pure or modified) binders, putties and mixes, the experimental campaign carried out both in the small strain domain and in the large strain domain, is presented. The low temperature behavior of binders has been evaluated with three common fundamental tests: i)the complex modulus determination, ii)the Bending Beam Rheometer and iii)the tensile strength at a constant strain rate and constant temperatures. A new three point bending test on pre-notched bitumen beams has also been developed at the ENTPE. The low-temperature fracture properties of bitumens were studied at constant temperatures and cross-head speeds considering the Linear Elastic Fracture Mechanics (LEFM) assumptions. The thermo-mechanical behavior of bituminous mixtures has been studied by performing i)complex modulus tests, ii)measurements of the coefficient of thermal dilatation and contraction, iii)tensile tests at constant temperatures and strain rates, and iv)Thermal Stress Restrained Specimen Tests. Apart from the determination of some pertinent links between binder and mix properties and discriminating characteristics with regard to the thermal cracking of bituminous mixes at low temperatures, the analysis has also consisted in modeling the behavior of

  6. Study of the contribution from gamma dose rate and radon concentration in civilian housing caused by the use of construction material having processing residues from uranium containing bituminous coal in Freital, Saxony

    International Nuclear Information System (INIS)

    The past, widerspread use of residues from processing uranium containing bituminous coal in the former mining region of Freital, Saxony, for construction led to increased concentrations of natural radionuclides in the building material of civilian housing. Measurement of the local dose levels in such housing, analytical characterization of the building material, and model calculations allow for the assessment of the contribution of the material to the total radioactive exposure of residents. (orig.)

  7. Development of a method to determine the nuclide inventory in bituminized waste packages; Entwicklung eines Verfahrens zur Bestimmung des Nuklidinventars in bituminierten Abfallgebinden

    Energy Technology Data Exchange (ETDEWEB)

    Mesalic, E.; Kortman, F.; Lierse von Gostomski, C. [Technische Univ. Muenchen, Garching (Germany). Zentrale Technisch-Wissenschaftliche Betriebseinheit Radiochemie Muenchen (RCM)

    2014-01-15

    Until the 1980s, bitumen was used as a conditioning agent for weak to medium radioactive liquid waste. Its use can be ascribed mainly to the properties that indicated that the matrix was optimal. However, fires broke out repeatedly during the conditioning process, so that the method is meanwhile no longer permitted in Germany. There are an estimated 100 waste packages held by the public authorities in Germany that require a supplementary declaration. In contrast to the common matrices, such as for example resins or sludges, there is still no standardized technology for taking samples and subsequently determining the radio-nuclide for bitumen. Aspects, such as the thermoplastic behaviour, make determining the nuclide inventory more difficult in bituminized waste packages. The development of a standardized technology to take samples with a subsequent determination of the radio-nuclide analysis is the objective of a project funded by the BMBF. Known, new methods, specially developed for the project, are examined on inactive bitumen samples and then transferred to active samples. At first non-destructive methods are used. The resulting information forms an important basis to work out and apply destructive strategy for sampling and analysis. Since the project is on-going, this report can only address the development of the sampling process. By developing a sampling system, it will be possible to take samples from an arbitrary selected location of the package across the entire matrix level and thus gain representative analysis material. The process is currently being optimized. (orig.)

  8. Changes in optical properties, chemistry, and micropore and mesopore characteristics of bituminous coal at the contact with dikes in the Illinois Basin

    Science.gov (United States)

    Mastalerz, Maria; Drobniak, A.; Schimmelmann, A.

    2009-01-01

    Changes in high-volatile bituminous coal (Pennsylvanian) near contacts with two volcanic intrusions in Illinois were investigated with respect to optical properties, coal chemistry, and coal pore structure. Vitrinite reflectance (Ro) increases from 0.62% to 5.03% within a distance of 5.5??m from the larger dike, and from 0.63% to 3.71% within 3.3??m from the small dike. Elemental chemistry of the coal shows distinct reductions in hydrogen and nitrogen content close to the intrusions. No trend was observed for total sulfur content, but decreases in sulfate content towards the dikes indicate thermochemical sulfate reduction (TSR). Contact-metamorphism has a dramatic effect on coal porosity, and microporosity in particular. Around the large dike, the micropore volume, after a slight initial increase, progressively decreases from 0.0417??cm3/g in coal situated 4.7??m from the intrusive contact to 0.0126??cm3/g at the contact. Strongly decreasing mesopore and micropore volumes in the altered zone, together with frequent cleat and fracture filling by calcite, indicate deteriorating conditions for both coalbed gas sorption and gas transmissibility. ?? 2008 Elsevier B.V. All rights reserved.

  9. Evaluation of Control Strategies to Effectively Meet 70-90% Mercury Reduction on an Eastern Bituminous Coal Cyclone Boiler with SCR

    Energy Technology Data Exchange (ETDEWEB)

    Tom Campbell

    2008-12-31

    This is the final site report for testing conducted at Public Service of New Hampshire's (PSNH) Merrimack Unit 2 (MK2). This project was funded through the DOE/NETL Innovations for Existing Plants program. It was a Phase III project with the goal to develop mercury control technologies that can achieve 50-70% mercury capture at costs 25-50% less than baseline estimates of $50,000-$70,000/lb of mercury removed. While results from testing at Merrimack indicate that the DOE goal was partially achieved, further improvements in the process are recommended. Merrimack burned a test blend of eastern bituminous and Venezuelan coals, for a target coal sulfur content of 1.2%, in its 335-MW Unit 2. The blend ratio is approximately a 50/50 split between the two coals. Various sorbent injection tests were conducted on the flue gas stream either in front of the air preheater (APH) or in between the two in-series ESPs. Initial mercury control evaluations indicated that, without SO3 control, the sorbent concentration required to achieve 50% control would not be feasible, either economically or within constraints specific to the maximum reasonable particle loading to the ESP. Subsequently, with SO{sub 3} control via trona injection upstream of the APH, economically feasible mercury removal rates could be achieved with PAC injection, excepting balance-of-plant concerns. The results are summarized along with the impacts of the dual injection process on the air heater, ESP operation, and particulate emissions.

  10. CO2 capture from power plants. Part I : A parametric study of the technical performance based on monoethanolamine

    NARCIS (Netherlands)

    Abu-Zahra, M. R. M.; Schneiders, L. H. J.; Niederer, J. P. M.; Feron, P. H. M.; Versteeg, G. F.

    2007-01-01

    Capture and storage of CO2 from fossil fuel fired power plants is drawing increasing interest as a potential method for the control of greenhouse gas emissions. An optimization and technical parameter study for a CO2 capture process from flue gas of a 600 MWe bituminous coal fired power plant, based

  11. Study on the conditions of bituminization of radioactive wastes and their influence on the stability of stored products

    International Nuclear Information System (INIS)

    Investigations carried out on a laboratory and semi-industrial scale showed that the Polish oxidised industrial bitumen P-60 was suitable for the solidification of liquid radioactive waste and particularly for non-concentrated post-precipitation sludges. The bitumen products were highly stable and were resistant to leaching by acids, salt solutions and water. Laboratory leach tests gave values similar to those obtained by others using different bitumen. By evaluating the sorption characteristics of the soil and the hydrogeological conditions existing at a proposed storage site, it was shown that the solidified wastes could be stored directly in the soil without further isolation from the soil water. Based on the liquid wastes arising from a nuclear power plant it has been shown that solidification of the wastes in bitumen will be cheaper than solidification of the same wastes using cement

  12. Valuation of investments in natural resources using contingent-claim framework with application to bituminous coal developments in Korea

    International Nuclear Information System (INIS)

    As Brennan and Schwartz [Brennan M, Schwartz E. Evaluating natural resource investment. Journal of Business 1985;58:135-57] point out in their pioneering work, the valuation of natural resources projects is particularly difficult due to the high degree of uncertainty in output prices of resources. In general, there are two competing procedures to evaluate risky projects in natural resources developments. One is decision analytic, based on traditional discounted cash flow and stochastic dynamic programming [Fleten SE, Maribu KM, Wangensteen I. Optimal investment strategies in decentralized renewable power generation under uncertainty. Energy 2007;32:803-15; Smith J, McCardle K. Valuing oil properties: integrating option pricing and decision analysis approaches. Operations Research 1998;46(2):198-217; Szklo AS, Carneiro JTG, Machado G. Break-even price for upstream activities in Brazil: evaluation of the opportunity cost of oil production delay in a non-mature sedimentary production region. Energy 2008;33:589-600], and the other is contingent claims analysis, based on the no-arbitrage theory of financial markets [Brennan M, Schwartz E. Evaluating natural resource investment. Journal of Business 1985;58:135-57; Emhjellen M, Alaouze CM. A comparison of discounted cash flow and modern asset pricing methods - project selection and policy implications. Energy Policy 2003;31:1213-20; Laughton D. The management of flexibility in the upstream petroleum industry. The Energy Journal 1998;19:83-114; Paddock L, Siegel D, Smith J. Option valuation of claims on real assets: the case of offshore petroleum leases. Quarterly Journal of Economics 1988;103(3):479-508; Schwartz ES. Valuing long-term commodity assets. Journal of Energy Finance and Development 1998;3(2):85-99; Sezgen O, Goldman CA, Krishnarao P. Option value of electricity demand response. Energy 2007;32:108-19]. In this paper, we use the second approach to develop a new model, and the main contributions are providing a

  13. Valuation of investments in natural resources using contingent-claim framework with application to bituminous coal developments in Korea

    International Nuclear Information System (INIS)

    As Brennan and Schwartz [Brennan M, Schwartz E. Evaluating natural resource investment. Journal of Business 1985;58:135-57] point out in their pioneering work, the valuation of natural resources projects is particularly difficult due to the high degree of uncertainty in output prices of resources. In general, there are two competing procedures to evaluate risky projects in natural resources developments. One is decision analytic, based on traditional discounted cash flow and stochastic dynamic programming [Fleten SE, Maribu KM, Wangensteen I. Optimal investment strategies in decentralized renewable power generation under uncertainty. Energy 2007;32:803-15; Smith J, McCardle K. Valuing oil properties: integrating option pricing and decision analysis approaches. Operations Research 1998;46(2):198-217; Szklo AS, Carneiro JTG, Machado G. Break-even price for upstream activities in Brazil: evaluation of the opportunity cost of oil production delay in a non-mature sedimentary production region. Energy 2008;33:589-600], and the other is contingent claims analysis, based on the no-arbitrage theory of financial markets [Brennan M, Schwartz E. Evaluating natural resource investment. Journal of Business 1985;58:135-57; Emhjellen M, Alaouze CM. A comparison of discounted cash flow and modern asset pricing methods - project selection and policy implications. Energy Policy 2003;31:1213-20; Laughton D. The management of flexibility in the upstream petroleum industry. The Energy Journal 1998;19:83-114; Paddock L, Siegel D, Smith J. Option valuation of claims on real assets: the case of offshore petroleum leases. Quarterly Journal of Economics 1988;103(3):479-508; Schwartz ES. Valuing long-term commodity assets. Journal of Energy Finance and Development 1998;3(2):85-99; Sezgen O, Goldman CA, Krishnarao P. Option value of electricity demand response. Energy 2007;32:108-19]. In this paper, we use the second approach to develop a new model, and the main contributions are providing a

  14. Comprehensive geobiological characterization of a bituminous carbonate facies with Ediacara-type fossils (Shibantan Member, South China)

    Science.gov (United States)

    Duda, Jan-Peter; Blumenberg, Martin; Thiel, Volker; Simon, Klaus; Zhu, Maoyan; Reitner, Joachim

    2015-04-01

    The Shibantan Member (Dengying Formation, Ediacaran Period) is one of only few carbonate settings with Ediacara-type fossils worldwide (e.g. Ding & Chen, 1981; Sun, 1986; Xiao et al., 2005; Shen et al., 2009; Chen et al., 2014). However, only little is known about the sedimentology and biogeochemistry of the environments in which these organisms throve. Here we provide a comprehensive geobiological characterization of the Shibantan Member, addressing the interplay between sedimentary and (bio-) geochemical processes. Sedimentary analysis revealed that black laminated limestones of the lower Shibantan Member were deposited after a sudden local deepening in a subtidal lower- to middle ramp environment close to the storm wave base, while the dark wavy dolomites of the upper Shibantan Member were deposited in a subtidal middle ramp environment between storm- and fair weather wave base. Sedimentation in the Shibantan basin was generally highly dynamic as evidenced by a distinct slumping horizon and mass-flow deposits that were possibly due to synsedimentary tectonic processes. The microbial-mat associated biota including Ediacara-type fossils is restricted to the lower Shibantan Member. Sedimentary analysis of this part reveals a close relationship between autochthonous mat growth and allochthonous and/or para-autochthonous event deposition. During deposition of the lower Shibantan Member the water column was probably temporarily stratified, with a sub- to anoxic water layer (evidenced by Ni/Co-, V/(V+Ni) and V/Sc ratios) overlain by a oxygenated upper layer (evidenced by negative Ce anomalies and low V/Cr ratios). However, such stratification was not permanent, as mixing by storm events is evidenced by hummocky cross stratification structures. 13C-enrichments in carbonates of the Lower Shibantan Member (δ13C = +3.3 to +4.0o VPDB) together with 13C-depletions of syngenetic n-alkanes cleaved from the respective extraction residue using catalytic hydropyrolysis (HyPy;

  15. Microbial activity in argillite waste storage cells for the deep geological disposal of French bituminous medium activity long lived nuclear waste: Impact on redox reaction kinetics and potential

    Science.gov (United States)

    Albrecht, A.; Leone, L.; Charlet, L.

    2009-04-01

    Micro-organisms are ubiquitous and display remarkable capabilities to adapt and survive in the most extreme environmental conditions. It has been recognized that microorganisms can survive in nuclear waste disposal facilities if the required major (P, N, K) and trace elements, a carbon and energy source as well as water are present. The space constraint is of particular interest as it has been shown that bacteria do not prosper in compacted clay. An evaluation of the different types of French medium and high level waste, in a clay-rich host rock storage environment at a depth between 500 and 600 m, has shown that the bituminous waste is the most likely candidate to accommodate significant microbial activity. The waste consists of a mixture of bitumen (source of bio-available organic matter and H2 as a consequence of its degradation and radiolysis) and nitrates and sulphates kept in a stainless steel container. The assumption, that microbes only have an impact on reaction kinetics needs to be reassessed in the case where nitrates and sulphates are present since both are known not to react at low temperatures without bacterial catalysis. The additional impact of both oxy-anions and their reduced species on redox conditions, radionuclide speciation and mobility gives this evaluation their particular relevance. Storage architecture proposes four primary waste containers positioned into armoured cement over packs and placed with others into the waste storage cell itself composed of a cement mantle enforcing the argillite host rock, the latter being characterized by an excavation damaged zone constricted both in space and in time and a pristine part of 60 m thickness. Bacterial activity within the waste and within the pristine argillite is disregarded because of the low water activity (low mobility of critical RN, • increased retardation of mobile RN in biofilms (i.e. adsorption on microbial cell surfaces and products of possible biomineralization); complexation by

  16. Thermal relaxation of bituminous coal to improve donation ability of hydrogen radicals in flash pyrolysis; Sekitan kozo kanwa ni yoru suiso radical kyoyo noryoku no kojo wo mezashita netsubunkai mae shori

    Energy Technology Data Exchange (ETDEWEB)

    Mori, T.; Isoda, T.; Kusakabe, K.; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hayashi, J. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

    1996-10-28

    In terms of coal conversion reaction, the behavior of bituminous coal heated beyond a glass transition point was examined on the basis of pyrolyzed products, and the effect of an increase in proton mobility on promotion of coal decomposition was evaluated. In experiment, after Illinois bituminous coal specimen was heated up to a specific temperature in N2 or He gas flow at a rate of 5K/min, the specimen was directly transferred to a pyrolyzer for instantaneous pyrolysis. As the experimental result, the glass transition temperature of the Illinois coal specimen was calculated to be 589K from a differential scanning calorimetry (DSC) profile. From the pyrolysis result of the Illinois coal specimen heated up to 623K, the char yield decreased by 3kg as compared with that of the original coal, while the tar yield increased by 4kg up to 27kg per 100kg of the original coal. This tar increase was larger than that of cooled coal. These results suggested that the donation of hydrogen radicals to coal fragments is improved with an increase in proton mobility. 4 refs., 4 figs., 1 tab.

  17. 基于APA的沥青混合料水稳性试验研究%Experimental investigation of cement stability of bituminous mixture based on APA

    Institute of Scientific and Technical Information of China (English)

    李亿龙

    2007-01-01

    分析了几种评价沥青混合料水稳性的方法,比较了其特点以及存在的问题,通过对不同级配的沥青混合料进行APA浸水车辙试验,得出APA浸水车辙试验评价沥青混合料的水稳性能较好模拟实际路面发生水损害的结论.

  18. The Role of Bituminous Sands in Extending the Petroleum Era Beyond 2000 A. D. (Summary Le rôle des sables bitumineux pour prolonger l'ère du pétrole au-delà de l'an 2000 (résumé

    Directory of Open Access Journals (Sweden)

    Carrigy M.

    2006-10-01

    Full Text Available Bituminous sand is an energy resource that is receiving increasing attention and there is a strong interest by the international community in co-operating in the development of new methods of exploration, and in the solution of common technological problems to reduce the time when oil from this enormous energy source is available. A detailed knowledge of the geological setting and the reservoir is of paramount importance to the assessment of the magnitude of the resource, its successful exploitation and to facilitate the transfer of the highly complicated recovery technology from one deposit to another. Much research also remains to be done to improve our understanding of the origin of the bitumen and the factors controlling the location of its accumulation. Based on the scant information we have, it is estimated that bituminous sand deposits contain from 5 to 10 x 10. 12 (trillion barrels of crude bitumen and are surely large enough to make a significant contribution to extending the petroleum era until alternative energy sources are developed. However, great amounts of synthetic oil from this source will probably not be brought onto the market until after the year 2000 A. D. because of the high capital cost, and large numbers of skilled technicians required to bring them into production. In the more industrialized nations where the demand for portable liquid fuel is strongest, notably Canada, Venezuela, and USA, billions of dollars are being spent on exploring and exploiting their bituminous sand resources. It is, however, in those undeveloped nations, who cannot afford to buy light crude oil, and who have bituminous deposits, where exploitation of this resource should have its greatest impact. It is therefore imperative that all geologists be aware of the new technologies that are now available to turn these low-grade hydrocarbons into high-grade products. Une attention croissante est accordée aux sables bitumineux comme source d

  19. Dust is the dominant source of "heavy metals" to peat moss (Sphagnum fuscum) in the bogs of the Athabasca Bituminous Sands region of northern Alberta.

    Science.gov (United States)

    Shotyk, William; Bicalho, Beatriz; Cuss, Chad W; Duke, M John M; Noernberg, Tommy; Pelletier, Rick; Steinnes, Eiliv; Zaccone, Claudio

    2016-01-01

    Sphagnum fuscum was collected from twenty-five ombrotrophic (rain-fed) peat bogs surrounding open pit mines and upgrading facilities of Athabasca Bituminous Sands (ABS) in northern Alberta (AB) in order to assess the extent of atmospheric contamination by trace elements. As a control, this moss species was also collected at a bog near Utikuma (UTK) in an undeveloped part of AB and 264km SW of the ABS region. For comparison, this moss was also collected in central AB, in the vicinity of the City of Edmonton which is approximately 500km to the south of the ABS region, from the Wagner Wetland which is 22km W of the City, from Seba Beach (ca. 90km W) and from Elk Island National Park (ca. 45km E). All of the moss samples were digested and trace elements concentrations determined using ICP-SMS at a commercial laboratory, with selected samples also analyzed using instrumental neutron activation analysis at the University of Alberta. The mosses from the ABS region yielded lower concentrations of Ag, As, Bi, Cd, Cu, Pb, Sb, Tl, and Zn compared to the moss from the Edmonton area. Concentrations of Ni and Mo in the mosses were comparable in these two regions, but V was more abundant in the ABS samples. Compared with the surface vegetation of eight peat cores collected in recent years from British Columbia, Ontario, Quebec and New Brunswick, the mean concentrations of Ag, As, Bi, Cd, Cu, Mo, Ni, Pb, Sb, Tl and Zn in the mosses from the ABS region are generally much lower. In fact, the concentrations of these trace elements in the samples from the ABS region are comparable to the corresponding values in forest moss from remote regions of central and northern Norway. Lithophile element concentrations (Ba, Be, Ga, Ge, Li, Sc, Th, Ti, Zr) explain most of the variation in trace metal concentrations in the moss samples. The mean concentrations of Th and Zr are greatest in the moss samples from the ABS region, reflecting dust inputs to the bogs from open pit mines, aggregate

  20. 某600 MW机组烟煤锅炉低N0x改造及效果分析%Low NOx Retrofit for Certain 600 MW Bituminous Coal Boiler and Performance Analysis

    Institute of Scientific and Technical Information of China (English)

    鲁鹏飞

    2013-01-01

    The retrofit effect of certain 600 MW bituminous coal boiler indicates that low NOx combustion technology can reduce the NOx production to 70%, but there are some problems, such as combustion economy and large spray water. Strong reduction atmosphere of burner zone may cause high temperature corrosion on water wall. Therefore, it is suggested to spray some anticorrosive material for prevention.%对某600 MW机组烟煤锅炉进行低NOx改造,改造后锅炉总体性能良好,NOx减排达到70%.但改造对锅炉燃烧经济性、减温水量产生负面影响,同时主燃烧器区形成的强还原性气氛还可能对水冷壁造成高温腐蚀,必须采取喷涂等防腐手段加以预防.

  1. Energy Analysis of a Biomass Co-firing Based Pulverized Coal Power Generation System

    OpenAIRE

    Marc A. Rosen; Shoaib Mehmood; Bale V. Reddy

    2012-01-01

    The results are reported of an energy analysis of a biomass/coal co-firing based power generation system, carried out to investigate the impacts of biomass co-firing on system performance. The power generation system is a typical pulverized coal-fired steam cycle unit, in which four biomass fuels (rice husk, pine sawdust, chicken litter, and refuse derived fuel) and two coals (bituminous coal and lignite) are considered. Key system performance parameters are evaluated for various fuel combina...

  2. Development of bituminous coal liquefaction technology. ; Study using a small device (study on synthetic iron sulfide catalyst). Rekiseitan ekika gijutsu no kaihatsu. ; Kogata sochi ni yoru kenkyu (gosei ryukatetsu shokubai no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    Ueda, S. (New Energy and Industrial Technology Development Organization, Tokyo (Japan))

    1993-09-01

    This paper reports the execution of device procurement and building construction of small equipment to manufacture synthetic iron sulfide for catalysts used in the NEDOL bituminous coal liquefaction process, carried out in the fiscal year 1992. To study synthetic iron sulfide catalysts manufactured by the dry manufacturing method, it has been planned to install small equipment with a catalyst manufacturing capacity of 10 kg/hr in a process supporting unit (PSU) plant. Major devices and electric measuring instruments have been procured. The construction work included civil engineering and building constructions for part of buildings to accommodate the whole equipment used in the sintering process and an electric room adjoining thereto. Because this small equipment serves also as a PSU exhaust gas treatment facility to treat exhaust gas containing SO2 produced as a sub-product in the sintering process, the PSU exhaust gas treatment process was modified, and the trial operation was carried out in September 1992. Technical standards and operation methods were discussed on each of the sintering process and the exhaust gas treatment process in the small equipment. A process instruction document, and an operation standard for steady operation, start-up and shutdown were prepared.

  3. EFFECT OF COAL-SWELLING AND SYNCHRONOUSLY SUPPORTED CATALYSTS ON COPROCESSING OF BITUMINOUS COAL AND HEAVY OILS%同步溶胀-担载催化剂对烟煤-重油共炼的影响

    Institute of Scientific and Technical Information of China (English)

    戈军; 石斌; 郭龙德; 郭智慧; 田华; 张建芳

    2011-01-01

    以Fe(NO3)3和Na2S分别作为催化剂前体和原位硫化剂,在20℃下分别用水、甲醇(M)、N-N二甲基甲酰胺(DMF)和二甲亚砜(DMSO)对神华烟煤溶胀12 h,同步溶胀-担载催化剂后的烟煤脱除溶剂后与轮古常渣(LGAR)和杜84超稠油(Du84)在2:1油煤质量比,8 MPa冷氢压,420℃,1h的条件下进行加氢共处理.结果表明,神华烟煤经过溶胀处理后与两种重油共处理的液化率都明显提高,煤的转化率明显增大;三种有机溶胀剂相比,DMF同步溶胀促进液化效果最好,其次为DMSO,甲醇最差.两种配油相比,Du84比LGAR更适合煤-重油共处理.XRD分析表明,同步溶胀-担载法制备的溶胀煤栽铁催化剂以非晶态和高分散的状态存在于溶胀煤表面,在共处理中催化剂最终转化为Fe1-xS.在煤-重油共处理中,经DMF同步溶胀-担载的催化剂失活,结晶相对不明显.%Fe(NO3)3 as catalytic precursor and Na2S as in-situ presulfurizer were impregnated on the Shenhua bituminous coals which were synchronously swollen with H2O, methanol, N-N dimethylformamide (DMF) or dimethyl sulfoxide(DMSO) at 20 'C for 12 h. Then the swollen coals were prepared by vacuum drying. The co-processing of swollen Shenhua coal and two heavy oils(LGAR and Du84) was carried on under the condition of the mass ratio of 2:1 oil to coal, 8 Mpa cold hydrogen pressure,420℃ and 1 h. The coprocessing of the swollen bituminous coal and LGAR or Du84 was significantly improved on the coal liquefaction. Among the three swelling solvents, the improvement of DMF was the highest, that of DMSO was the better and methanol were the lowest. Du84 was favor in the coprocessing than LGAR. By XRD analysis, the iron catalysts on the swollen coal with Fe(NO3)3 synchronously impregnated with the solvents were amorphous and highly dispersed on coal surface and could transform into Fe1-x S in the coprocessing. During the coprocessing, the deactivation of the catalyst synchronously impregnated on

  4. Experimental study on the characteristics of NOx emissions from 600 MW supercritical bituminous coal fired boiler with swirl burner%600MW超临界旋流燃烧烟煤锅炉NOx排放特性试验

    Institute of Scientific and Technical Information of China (English)

    岳峻峰; 秦鹏; 邹磊; 梁绍华; 张恩先; 黄磊

    2012-01-01

    针对某厂1台600MW超临界低NOx轴向旋流燃烧烟煤锅炉特点,通过变工况(氧量、不同层燃烧器风量分配方式、二次风比率、二次风旋流强度、三次风旋流强度、同层燃烧器风量分配方式和负荷等)试验,分析了锅炉NOx排放特性.试验结果表明:对于燃用烟煤的采用低NOx旋流燃烧器的锅炉,运行氧量燃尽风份额、锅炉负荷及同层燃烧器风量分配方式是NOx排放的主要影响因素.为控制NOx排放,保持锅炉原有热效率,燃烧调整的原则为:(1)在保证锅炉运行安全的前提下应尽量采用低氧燃烧;(2)采用大比例的燃尽风份额;(3)运行负荷不应过低;(4)同层燃烧器风量分配采用双峰方式.%NOx. emissions from a 600 MW supercritical boiler with swirl burner were investigated by performing a serial of tests such as changing O2 concentration, air-distribution of different level burners, secondary air ratio, secondary and tertiary air swirl strength, air-distribution of the burners in same level and boiler load. The test results show that for the bituminous coal fired boiler with swirl burner, the O2 concentration, over fire air (OFA) ratio, boiler load and air-distribution mode of the burners in same level are the main factors affecting NOx emissions. In order to reduce NOx emissions and keep higher boiler efficiency, the following principles about combustion adjustment should be obeyed: (1) the O2 concentration should be kept in the premise of ensuring safe operalion of boiler as lower as possible;{2) large proportion of OFA should be adopted; (3) boiler load should not be loo low; (4) two-peak air distribution mode should be taken among the same level burners.

  5. Deformation Properties and Fatigue of Bituminous Mixtures

    OpenAIRE

    Frantisek Schlosser; Jan Mikolaj; Viera Zatkalikova; Juraj Sramek; Dominika Durekova; Lubos Remek

    2013-01-01

    Deformation properties and fatigue performance are important characteristics of asphalt bound materials which are used for construction of pavement layers. Viscoelastic asphalt mixtures are better characterized via dynamic tests. This type of tests allows us to collate materials with regard to axle vibrations which lie usually in the range of 6 Hz–25 Hz for standard conditions. Asphalt modified for heat sensitivity in the range from −20°C to +60°C has significant impact on the overall charact...

  6. Development of New Bituminous Pavement Design Method

    DEFF Research Database (Denmark)

    Ullidtz, Per

    The report and work of COST Action 333 sets in place the foundation for a coherent, cost-effective and harmonised European pavement design method. In order to do this, the work programme focused on information gathering, identification of requirements and the selection of the necessary design...

  7. Deformation Properties and Fatigue of Bituminous Mixtures

    Directory of Open Access Journals (Sweden)

    Frantisek Schlosser

    2013-01-01

    Full Text Available Deformation properties and fatigue performance are important characteristics of asphalt bound materials which are used for construction of pavement layers. Viscoelastic asphalt mixtures are better characterized via dynamic tests. This type of tests allows us to collate materials with regard to axle vibrations which lie usually in the range of 6 Hz–25 Hz for standard conditions. Asphalt modified for heat sensitivity in the range from −20°C to +60°C has significant impact on the overall characteristics of the mixture. Deformation properties are used as inputs for empirical mixture design, and fatigue performance of asphalt mixtures reflects the parameters of functional tests. Master curves convey properties of asphalt mixtures for various conditions and allow us to evaluate them without the need of time expensive testing.

  8. Enteric virus removal inactivation by coal-based media

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, A.; Chaudhuri, M. [Indian Institute of Technology, Kanpur (India). Dept. of Civil Engineering

    1995-02-01

    Four coal-based media, viz. alum-pretreated or ferric hydroxide-impregnated Giridih bituminous coal and lignite (alum-GBC, Fe-GBC; alum-lignite and Fe-Lignite) were laboratory tested to assess their potential in removing/inactivating enteric viruses in water. Batch-sorption screening tests, employing a poliovirus-spiked canal water, indicated high poliovirus sorption by Fe-GBC and alum-GBC in a short contact time of 5 min. Based on the results of further batch-sorption tests, using silver incorporated media (alum/Ag-GBC, alum-GBC-Ag and Fe-GBC-Ag), as well as aesthetic water quality consideration and previous findings on removal of coliforms and turbidity, alum/Ag-GBC, alum-GBC and alum-GBC-AG were included in downflow column studies employing poliovirus-spiked canal water. All three media showed potential in removing/inactivating enteric viruses. In a separate column study employing a joint challenge of poliovirus and rotavirus, alum/Ag-GBC removed 59.3-86.5% of the viruses along with more than 99% reduction in indigenous heterotrophic bacteria. Alum/silver-pretreated bituminous coal medium appears promising for use in household water filters in rural areas of the developing world. However, improved medium preparation to further enhance its efficiency is needed; also, its efficacy in removing/inactivating indigenous enteric bacteria, viruses and protozoa has to be ensured and practicalities or economics of application need to be considered.

  9. Relationship between high incidence of lung cancer among non-smoking women and silica in C1 bituminous coal in Xuanwei, Yunnan Province, China%云南省宣威地区非吸烟女性肺癌与C1烟煤中二氧化硅的关系

    Institute of Scientific and Technical Information of China (English)

    李光剑; 黄云超; 田林玮; 刘拥军; 郭律; 肖义泽; 侯文俊; 杨堃; 陈颖

    2013-01-01

    二氧化硅颗粒物进入室内空气中随悬浮颗粒物吸入肺部”的迁移富集路线.%Objective To measure the content of silica in C1 bituminous coal and its combustion products in the high-incidence area of lung cancer in Xuanwei,Yunnan Province,China and to investigate the relationship between high incidence of lung cancer among non-smoking women and silica produced naturally in C1 bituminous coal in Xuan Wei.Methods The C1 bituminous coal widely used in the high-incidence area of lung cancer in Xuanwei was selected as experiment group,while the C2+1,K7,and M30 bituminous coal that was mined and used in the low-incidence area of lung cancer in Xuanwei for more than 10 years were selected as control group.Fourteen paraffin-embedded cancer tissue samples from the non-smoking women with non-small cell lung cancer who were born in Xuanwei and were at least the 3rd generation of the family living there were collected from the department of pathology,the ahird affiliated hospital of kunming medical university (tumor hospital of yunnan province).Titrimetric potassium silicofluoride method was used to measure the content of silica in raw coal and its bottom ashes in 20 samples from the experimental group and control group.Scanning electron microscopy (SEM) was used to observe the morphology of silica particles in C1 bituminous coal and its bottom ashes,and scanning electron microscopy coupled with energy dispersive X-ray analyzer (SEM-EDX) was used to analyze the microscopic composition.Transmission electron microscope (TEM) was used to observe the morphology of silica particles in the bottom ashes and coal soot of C1 bituminous coal as well as the lung cancer tissue from the non-smoking women in Xuanwei,and transmission electron microscope coupled with energy dispersive X-ray analyzer (TEM-EDX) was used to analyze the microscopic composition.The silica particles were separated from the coal soot and bottom ashes and characterized by physical method

  10. A study on the carbon-based sorbents injection for gas phase mercury removal from flue gas

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.; Rhim, Y.; Kim, S.; Park, Y. (and others) [Korea Institute of Energy Research, Daejoen (Republic of Korea). Clean Energy Research Department

    2003-07-01

    To develop carbon-based sorbents to be used in gas-phase mercury removal, the performance of virgin activated carbons (AC) and that of chemically treated activated carbons were compared. Virgin activated carbons (ACs) were made of bituminous coal, lignite, anthracite and NSH4X10. Chemical treated ACs used were those impregnated with sulphuric acid, nitric acid, 1% sulfur, and with mixed sulphuric and nitric acid. Pre-oxidation of activated carbons with acids was also investigated and adsorption performances were compared. Injection of activated carbons has been investigated and the influential factors such as temperature, carbon dose were also discussed. 5 refs., 4 figs., 2 tabs.

  11. Experimental evaluation of high performance base course and road base asphalt concrete with electric arc furnace steel slags.

    Science.gov (United States)

    Pasetto, Marco; Baldo, Nicola

    2010-09-15

    The paper presents the results of a laboratory study aimed at verifying the use of two types of electric arc furnace (EAF) steel slags as substitutes for natural aggregates, in the composition of base course and road base asphalt concrete (BBAC) for flexible pavements. The trial was composed of a preliminary study of the chemical, physical, mechanical and leaching properties of the EAF steel slags, followed by the mix design and performance characterization of the bituminous mixes, through gyratory compaction tests, permanent deformation tests, stiffness modulus tests at various temperatures, fatigue tests and indirect tensile strength tests. All the mixtures with EAF slags presented better mechanical characteristics than those of the corresponding asphalts with natural aggregate and satisfied the requisites for acceptance in the Italian road sector technical standards, thus resulting as suitable for use in road construction. PMID:20566237

  12. Radioactivity concentrations and dose assessment for bitumen and soil samples around a bituminous deposit in Ondo State, Nigeria; Radioactivite et evaluation de la dose dans des echantillons de bitume et de sol autour d'un depot bitumineux dans l'etat d'Ondo, Nigeria

    Energy Technology Data Exchange (ETDEWEB)

    Ademola, J.A.; Ademonehin, S. [Department of Physics, University of Ibadan, Ibadan (Nigeria)

    2010-07-15

    Bitumen samples and soil samples around a bituminous deposit in Ondo State, Nigeria, were analysed for {sup 40}K, {sup 226}Ra and {sup 232}Th employing gamma-ray spectrometry. The activity concentrations of {sup 40}K, {sup 226}Ra and {sup 232}Th in soil varied from (45.2 {+-} 5.3) to (484.2 {+-} 25.9), BDL (below detectable limit) to (27.7 {+-} 2.1) and (22.8 {+-} 2.7) to (62.4 {+-} 6.8) Bq.kg{sup -1}, respectively. The corresponding mean values were (240.2 {+-} 133.5), (13.3 {+-} 8.0) and (40.0 {+-} 10.2) Bq.kg{sup -1}, respectively. The mean activity concentrations of the radionuclides in the bitumen were (58.4 {+-} 36.4), (16.1 {+-} 13.3) and (32.5 {+-} 13.1) Bq.kg{sup -1}, respectively, for {sup 40}K, {sup 226}Ra and {sup 232}Th. The mean absorbed dose and effective dose for the soil samples were (41.5 {+-} 8.9) nGy.h{sup -1} and (50.7 {+-} 10.9) {mu}Sv.y{sup -1}, respectively, while those of the bitumen samples were (29.5 {+-} 15.6) nGy.h{sup -1} and (36.1 {+-} 19.1) {mu}Sv.y{sup -1}, respectively. For radiological hazard assessment, the radium equivalent activity and the external hazard index were determined. The values of the radium equivalent activity and external hazard index obtained for the soil and bitumen samples were lower than the recommended limit. (authors)

  13. Energy Analysis of a Biomass Co-firing Based Pulverized Coal Power Generation System

    Directory of Open Access Journals (Sweden)

    Marc A. Rosen

    2012-03-01

    Full Text Available The results are reported of an energy analysis of a biomass/coal co-firing based power generation system, carried out to investigate the impacts of biomass co-firing on system performance. The power generation system is a typical pulverized coal-fired steam cycle unit, in which four biomass fuels (rice husk, pine sawdust, chicken litter, and refuse derived fuel and two coals (bituminous coal and lignite are considered. Key system performance parameters are evaluated for various fuel combinations and co-firing ratios, using a system model and numerical simulation. The results indicate that plant energy efficiency decreases with increase of biomass proportion in the fuel mixture, and that the extent of the decrease depends on specific properties of the coal and biomass types.

  14. Mix design of bituminous materials including reclaimed asphalt pavement

    OpenAIRE

    Dubois, Vincent; De La Roche, Chantal

    2008-01-01

    Reclaimed asphalt, obtained by milling of asphalt road layers can be re-used at once or stored. In the case of storage, an heterogeneity issue may occur when several types of materials, with different origins are mixed. At the scale of a storage zone or a stock pile, composition and properties of the reclaimed asphalts will be different, including variations of the final material properties, constraints for the stock manager, and the necessary adaptation of the manufacturing process. The recl...

  15. A STUDY OF BITUMINOUS SHUNGITE BINDER ON THE SCANNING MICROSCOPE

    Directory of Open Access Journals (Sweden)

    K. A. Andrianov

    2012-07-01

    Full Text Available Statement of the problem. It is possible to improve working conditions of road pavement and to use it more efficiently by regulating water-thermal conditions of the subgrade thereby reducing humidity in the design period and mitigating its seasonal changes.Results and conclusions. It is suggested to use extruded foam polystyrene as a heating layer. The thermal fluctuation approach was applied to failure and deformation processes. Physical constants for the analytical description of these processes at varying temperatures and stresses are calculated. The technique for determining acting stresses and temperatures was described. The prediction of the durability of extruded foam polystyrene in road structure is presented.

  16. A STUDY OF BITUMINOUS SHUNGITE BINDER ON THE SCANNING MICROSCOPE

    OpenAIRE

    K. A. Andrianov; D V Ivanov; V. P. Yartsev

    2012-01-01

    Statement of the problem. It is possible to improve working conditions of road pavement and to use it more efficiently by regulating water-thermal conditions of the subgrade thereby reducing humidity in the design period and mitigating its seasonal changes.Results and conclusions. It is suggested to use extruded foam polystyrene as a heating layer. The thermal fluctuation approach was applied to failure and deformation processes. Physical constants for the analytical description of these proc...

  17. Some thoughts on the organic structure of bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, J. W.

    1978-01-01

    Our current operating hypothesis is that coal consists of a cross linked macromolecular network of high aromatic clusters held together by linkages which include ethers and methylene groups. These clusters are arranged like beads on a string with 3 to 5 beads between branch points. Coal can be liqufied most readily by cleaving the links between the clusters. Doing chemistry on the clusters in the whole coal is very difficult because of the problems of getting to the clusters by reagents. It is fortunate that the linkages between clusters are quite reactive. But even with this, it is clear that coal liquefaction is a formidable chemical problem. There is much wisdom is Sternberg's suggestion that the chemistry of the freed clusters (pre-asphaltenes) be developed. Our model indicates that the chemistry which results in freeing the clusters from the network also should be explored and broadened.

  18. Natural analogues of bitumen and bituminized radioactive waste

    International Nuclear Information System (INIS)

    Occurrences of natural bitumen provide possibilities to identify and assess materials, processes, phenomena and conditions in nature which can serve as model cases valid also with respect to a final repository. Natural bitumens meet the basic requirements for use as natural analogues. In natural sites, processes of bitumen formation and degradation often work simultaneously. The major processes are thermal alteration, evaporation, reaction with water, biodegradation, oxidation, weathering and radiation degradation. Progress in analytical organic geochemistry made during recent years has enabled a deeper understanding of the structural and compositional effects of these processes on bitumen. This is necessary in natural analogue applications. The time scales involved in degradation processes, as observed in natural occurrences, exceed the time scales dictated by the half-lives of most important fission products in low and medium level waste by orders of magnitude. Only exposure to the weather at the surface leads to a more rapid destruction of bitumen. Trace metals in bitumen arenot released until the matrix is completely destroyed. Products of radiation degradation and weathering of bitumen are able, to a certain degree, to delay migration of the metal ions released. Impregnation with bitumen may effectively reduce the microbial decomposition of easily destructable organic waste components, as can be deduced on the basis of the excellent preservation of fossils observed in bitumen. The complexity of all the natural sites described requires extensive understanding of the origin and kind of organic material in bitumen, its maturation, migration, alteration and degradation and of the geological and tectonic evolution of the site. The latter is used for establishing the time scale

  19. Characterisation of cemented/bituminized LAW and MAW waste products

    International Nuclear Information System (INIS)

    In the context of work for characterising low and medium activity waste products, investigations were carried out to determine the release of radioactivity from binding waste in given accidents, such as mechanical and thermal loading for the operating phase of a final store. The effects of mechanical loads on MAW cement products and the effects of thermal laods on MAW cement and MAW bitumen products were examined. The release of fine dust reaching the lungs, with a particle size of ≤10 μm from a 200 litre roller seam cement binder with a maximum mechanical load of 3x105 Nm covering the accident case is about 1.5 g and therefore corresponds to ≅ 10-4% of the total radio-activity inventory for homogeneous products. With thermal loading (60 minute oil fire, 8000C) ≅ 10-3% of the radioactivity inventory is released via the release of water from the waste binder. The activity release of MAW bitumen products containing NaNO3 (175 litre drum) with thermal load is considerably higher, as due to the NaNO3 content of the products, after an induction period of about 20 minutes there is an exothermal reaction between the bitumen and the NaNO3, which leads to burning of the bitumen with considerable aerosol formation. The Na losses are about 32% and the Pu losses, derived from the results of laboratory experiments with samples containing Eu and Pu and samples containing Eu on the original size, are only 15% maximum, even with complete burn up. It was shown for all the investigations with samples of the original size that the effects of the load cases considered can be reduced or completely avoided by additional packing (concrete shielding). (orig./RB)

  20. Use of waste plastic in construction of bituminous road

    Directory of Open Access Journals (Sweden)

    Abhijeet Jirge

    2012-05-01

    Full Text Available Bottles, containers and packing strips etc. is increasing day by day. As a result amount of waste plastic also increases. This leads to various environmental problems. Many of the wastes produced today will remain in the environment for many years leading to various environmental concerns. Therefore it is necessary to utilize thewastes effectively with technical development in each field. Many by-products are being produced using the plastic wastes. Our present work is helping to take care of these aspects. Plastic waste, consisting of carry bags, cups and other utilized plastic can be used as a coating over aggregate and this coated stone can be used for roadconstruction. The mix polymer coated aggregate and tyre modified bitumen have shown higher strength. Use of this mix for road construction helps to use plastics waste. Once the plastic waste is separated from municipal solid waste, the organic matter can be converted into manure and used. Our paper will discuss in detail theprocess and its successful applications.

  1. Use of waste plastic in construction of bituminous road

    OpenAIRE

    Abhijeet Jirge; Karan patil; Mrs.Vidula Swami; Suhas patil; Sushil patil; Karan salokhe

    2012-01-01

    Bottles, containers and packing strips etc. is increasing day by day. As a result amount of waste plastic also increases. This leads to various environmental problems. Many of the wastes produced today will remain in the environment for many years leading to various environmental concerns. Therefore it is necessary to utilize thewastes effectively with technical development in each field. Many by-products are being produced using the plastic wastes. Our present work is helping to take care of...

  2. Method development for mass spectrometry based molecular characterization of fossil fuels and biological samples

    Science.gov (United States)

    Mahat, Rajendra K.

    In an analytical (chemical) method development process, the sample preparation step usually determines the throughput and overall success of the analysis. Both targeted and non-targeted methods were developed for the mass spectrometry (MS) based analyses of fossil fuels (coal) and lipidomic analyses of a unique micro-organism, Gemmata obscuriglobus. In the non-targeted coal analysis using GC-MS, a microwave-assisted pressurized sample extraction method was compared with the traditional extraction method, such as Soxhlet. On the other hand, methods were developed to establish a comprehensive lipidomic profile and to confirm the presence of endotoxins (a.k.a. lipopolysaccharides, LPS) in Gemmata.. The performance of pressurized heating techniques employing hot-air oven and microwave irradiation were compared with that of Soxhlet method in terms of percentage extraction efficiency and extracted analyte profiles (via GC-MS). Sub-bituminous (Powder River Range, Wyoming, USA) and bituminous (Fruitland formation, Colorado, USA) coal samples were tested. Overall 30-40% higher extraction efficiencies (by weight) were obtained with a 4 hour hot-air oven and a 20 min microwave-heating extraction in a pressurized container when compared to a 72 hour Soxhlet extraction. The pressurized methods are 25 times more economic in terms of solvent/sample amount used and are 216 times faster in term of time invested for the extraction process. Additionally, same sets of compounds were identified by GC-MS for all the extraction methods used: n-alkanes and diterpanes in the sub-bituminous sample, and n-alkanes and alkyl aromatic compounds in the bituminous coal sample. G. obscuriglobus, a nucleated bacterium, is a micro-organism of high significances from evolutionary, cell and environmental biology standpoints. Although lipidomics is an essential tool in microbiological systematics and chemotaxonomy, complete lipid profile of this bacterium is still lacking. In addition, the presence of

  3. Transuranic contaminated waste form characterization and data base

    Energy Technology Data Exchange (ETDEWEB)

    Kniazewycz, B.G.; McArthur, W.C.

    1980-07-01

    This volume contains appendices A to F. The properties of transuranium (TRU) radionuclides are described. Immobilization of TRU wastes by bituminization, urea-formaldehyde polymers, and cements is discussed. Research programs at DOE facilities engaged in TRU waste characterization and management studies are described.

  4. Transuranic contaminated waste form characterization and data base

    International Nuclear Information System (INIS)

    This volume contains appendices A to F. The properties of transuranium (TRU) radionuclides are described. Immobilization of TRU wastes by bituminization, urea-formaldehyde polymers, and cements is discussed. Research programs at DOE facilities engaged in TRU waste characterization and management studies are described

  5. [Research and Design of an Experimental Apparatus Based on the "Open Fireplace" in Xuanwei District].

    Science.gov (United States)

    Yang, Jiapeng; Huang, Yunchao; Zi, Wenhua; Bai, Yunbao; Li, Guangjian; Ye, Lianhua; Zhou, Yongchun; Zhao, Guangqiang; Lei, Yujie; Chen, Xiaobo; Chen, Ying; Zhang Yanjun

    2016-02-01

    Xuanwei district in Yunnan Province of China has pretty high incidence of lung cancer in China, even a- round the world. Studies have shown that there exists a close relationship between lung cancer and local indoor air pollution caused by Bituminous coal. Considering that the indoor air pollution in Xuanwei District is caused by "open fireplace", an indoor air pollution simulation system was designed, and an F344 rats lung damage model was estab- lished for this indoor air pollution fireplace. The model is based on indoor air pollution simulation system with signal multiplexer control and multi-channel acquisition, and mining PID algorithm was used for polynomial fitting to each test point, and a relatively constant PM2. 5 air pollution status was simulated. The results showed that the system could simulate a variety of states of air pollution, provide a new test method for evaluation of human injury caused by indoor air pollution and a new idea for the study of the incidence of lung cancer in Xuanwei district and other places. PMID:27382748

  6. Novel nanodispersed coal liquefaction catalysts: Molecular design via microemulsion-based synthesis. Technical progress report, July--September 1993

    Energy Technology Data Exchange (ETDEWEB)

    Boakye, E.; Vittal, M.; Osseo-Asare, K. [and others

    1993-10-01

    The objective of this project is to pursue the development of highly dispersed and inexpensive catalysts for improved coal solubilization and upgrading of coal liquids. A novel study of the synthesis of liquefaction catalysts of manometer size is being carried out. It is based on the molecular design of inverse micelles (microemulsions). These surfactant-stabilized, metal-bearing microdrops offer unique opportunities for synthesizing very small particles by providing a cage-like effect that limits particle nucleation, growth and agglomeration. The emphasis is on molybdenum- and iron-based catalysts, but the techniques being developed should also be generally applicable. The size of these very small and monodispersed particles will be accurately determined both separately and after in situ and ex situ coal impregnation. The as-prepared nanoparticles as well as the catalyst-impregnated coal matrix are characterized using a battery of techniques, including dynamic light scattering, x-ray diffraction and transmission electron microscopy. Catalytic activity tests are conducted under standardized coal liquefaction conditions. The effects of particle size of these unsupported catalysts on the product yield and distribution during conversion of a bituminous and a subbituminous coal are being determined.

  7. Catalyst dispersion and activity under conditions of temperature- staged liquefaction. [Catalyst precursors for molybdenum-based catalyst and iron-based catalyst

    Energy Technology Data Exchange (ETDEWEB)

    Davis, A.; Schobert, H.H.; Mitchell, G.D.; Artok, L.

    1992-07-01

    Two coals, a Texas subbituminous C and a Utah high volatile A bituminous, were used to examine the effects of solvent swelling and catalyst impregnation on liquefaction conversion behavior in temperature staged reactions for 30 minutes each at 275{degree} and 425{degree}C in H{sub 2} and 95:5 H{sub 2}:H{sub 2}S atmospheres. Methanol, pyridine, tetrahydrofuran, and tetrabutylammonium hydroxide were used as swelling agents. Molybdenum-based catalyst precursors were ammonium tetrathiomolybdate, molybdenum trisulfide, molybdenum hexacarbonyl, and bis(tricarbonylcyclopentadienyl-molybdenum). Ferrous sulfate and bis(dicarbonylcyclo-pentadienyliron) served as iron-based catalyst precursors. In addition, ion exchange was used for loading iron onto the subbituminous coal. For most experiments, liquefaction in H{sub 2}:H{sub 2}S was superior to that in H{sub 2}, regardless of the catalyst precursor. The benefit of the H{sub 2}S was greater for the subbituminous, presumably because of its higher iron content relative to the hvab coal. Tetrabutylammonium hydroxide was the only swelling agent to enhance conversion of the hvab coal significantly; it also caused a remarkable increase in conversion of the subbituminous coal. The combined application of solvent swelling and catalyst impregnation also improves liquefaction, mainly through increased oil yields from the hvab coal and increased asphaltenes from the subbituminous. A remarkable effect from use of ammonium tetrathiomolybdate as a catalyst precursor is substantial increase in pristane and phytane yields. Our findings suggest that these compounds are, at least in part, bound to the coal matrix.

  8. Behaviour of selected major elements during fixed-bed gasification of South African bituminous coal

    OpenAIRE

    Bunt, J.R.; F.B. Waanders; Schobert, H.

    2012-01-01

    The Sasol-Lurgi Fixed Bed Dry Bottom gasifier (S-L FBDB) treats a feed coal containing c.a. 30% ash forming minerals, which means that there are complex mineralogical processes occurring simultaneously with each other, and in the gasification reactions, within the reactor. To obtain an understanding of the mineral transformational behaviour, a quenched commercial-scale S-L FBDB gasifier was sampled and characterized mineralogically. Crystalline phases measured by XRD analyses show the ash exi...

  9. Characterization and modelling of self healing of bituminous materials towards durable asphalt pavement

    OpenAIRE

    Qiu, J.; Van de Ven, M.F.C.; Schlangen, H.E.J.G.; Wu, S.; Molenaar, A.A.A.

    2012-01-01

    The traffic volume and the number of heavy vehicles are growing enormously nowadays. There is a need for designing a durable asphalt pavement with innovative technologies. Pavement structures and materials with self healing and self repairing capability are believed to be very useful in such a system. This paper is aiming to understand the self healing behaviour through mechanical testing and finite element modelling. Instead of a complex and time consuming fatigue involved self healing inves...

  10. Eastern gas shales bibliography selected annotations: gas, oil, uranium, etc. Citations in bituminous shales worldwide

    Energy Technology Data Exchange (ETDEWEB)

    Hall, V.S. (comp.)

    1980-06-01

    This bibliography contains 2702 citations, most of which are annotated. They are arranged by author in numerical order with a geographical index following the listing. The work is international in scope and covers the early geological literature, continuing through 1979 with a few 1980 citations in Addendum II. Addendum I contains a listing of the reports, well logs and symposiums of the Unconventional Gas Recovery Program (UGR) through August 1979. There is an author-subject index for these publications following the listing. The second part of Addendum I is a listing of the UGR maps which also has a subject-author index following the map listing. Addendum II includes several important new titles on the Devonian shale as well as a few older citations which were not found until after the bibliography had been numbered and essentially completed. A geographic index for these citations follows this listing.

  11. Survey on product properties of bituminized waste concentrates from reprocessing, nuclear installations and nuclear power plants

    International Nuclear Information System (INIS)

    This report contains a brief survey on the product properties after solidification with bitumen of waste concentrates from reprocessing plants, nuclear research installations and nuclear power plants. The leach behaviour of bitumen products in water and saturated salt solutions is described as well as the radiolytic and thermal stability of the products. The reports also contain some data on sedimentation of salts fixed in bitumen. (orig.)

  12. Use of bottom ash from thermal power plant and lime as filler in bituminous mixtures

    Directory of Open Access Journals (Sweden)

    López-López, E.

    2015-06-01

    Full Text Available This study focuses on the characterization of bottom ash (PCC-BA and determining the mechanical characteristics of hot mix asphalt (HMA using PCC-BA and hydrated lime (HL as filler. Physical and chemical characterization of the bottom ash was carried out to evaluate its eventual reutilization as filler substitute. The materials tested in this study were made using 0%, 25%, 50%, 70% and 100% of PCC-BA combined with HL. HMA mixes were evaluated in terms of their engineering properties, namely: air voids in the mixes, water sensitivity, stiffness modulus, performance in wheel tracking test and fatigue resistance. The results obtained indicate that HMA mixes with a filler blend of 70% PCC-BA and 30% HL fulfil European standards and are suitable for light traffic or small infrastructures.Este estudio se centra en la caracterización de las cenizas de fondo (PCC-BA y la determinación de las características mecánicas de mezclas bituminosas en caliente (HMA, utilizando cenizas de fondo y la cal hidratada (HL como filler. Se realizó la caracterización física y química de las cenizas de fondo para evaluar su empleo como sustituto de filler. Las mezclas ensayadas en este estudio se realizaron utilizando 0%, 25%, 50%, 70% y 100% de cenizas de fondo combinadas con cal hidratada. Se evaluaron propiedades ingenieriles de las mezclas bituminosas, tales como los huecos de aire en las mezclas, la sensibilidad al agua, el módulo de rigidez, el ensayo de pista y la resistencia a la fatiga. Los resultados obtenidos indican que las mezclas bituminosas fabricadas con una combinación de filler del 70% de cenizas de fondo y el 30% cal hidratada, cumplen con las normas europeas y son adecuados para su aplicación con tráficos ligeros o en pequeñas infraestructuras.

  13. Development and evaluation of an automated reflectance microscope system for the petrographic characterization of bituminous coals

    Energy Technology Data Exchange (ETDEWEB)

    Hoover, D. S.; Davis, A.

    1980-10-01

    The development of automated coal petrographic techniques will lessen the demands on skilled personnel to do routine work. This project is concerned with the development and successful testing of an instrument which will meet these needs. The fundamental differences in reflectance of the three primary maceral groups should enable their differentiation in an automated-reflectance frequency histogram (reflectogram). Consequently, reflected light photometry was chosen as the method for automating coal petrographic analysis. Three generations of an automated system (called Rapid Scan Versions I, II and III) were developed and evaluated for petrographic analysis. Their basic design was that of a reflected-light microscope photometer with an automatic stage, interfaced with a minicomputer. The hardware elements used in the Rapid Scan Version I limited the system's flexibility and presented problems with signal digitization and measurement precision. Rapid Scan Version II was designed to incorporate a new microscope photometer and computer system. A digital stepping stage was incorporated into the Rapid Scan Version III system. The precision of reflectance determination of this system was found to be +- 0.02 percent reflectance. The limiting factor in quantitative interpretation of Rapid Scan reflectograms is the resolution of reflectance populations of the individual maceral groups. Statistical testing indicated that reflectograms were highly reproducible, and a new computer program, PETAN, was written to interpret the curves for vitrinite reflectance parameters ad petrographic.

  14. Contribution of Ash Content Related to Methane Adsorption Behaviors of Bituminous Coals

    Directory of Open Access Journals (Sweden)

    Yanyan Feng

    2014-01-01

    Full Text Available Methane adsorption isotherms on coals with varying ash contents were investigated. The textural properties were characterized by N2 adsorption/desorption isotherm at 77 K, and methane adsorption characteristics were measured at pressures up to 4.0 MPa at 298 K, 313 K, and 328 K, respectively. The Dubinin-Astakhov model and the Polanyi potential theory were employed to fit the experimental data. As a result, ash content correlated strongly to methane adsorption capacity. Over the ash range studied, 9.35% to 21.24%, the average increase in methane adsorption capacity was 0.021 mmol/g for each 1.0% rise in ash content. With the increasing ash content range of 21.24%~43.47%, a reduction in the maximum adsorption capacities of coals was observed. In addition, there was a positive correlation between the saturated adsorption capacity and the specific surface area and micropore volume of samples. Further, this study presented the heat of adsorption, the isosteric heat of adsorption, and the adsorbed phase specific heat capacity for methane adsorption on various coals. Employing the proposed thermodynamic approaches, the thermodynamic maps of the adsorption processes of coalbed methane were conducive to the understanding of the coal and gas simultaneous extraction.

  15. Waste to Wealth; The Utilization of Scrap Tyre as Aggregate in Bituminous Mixes for Road Construction

    OpenAIRE

    Oba, A. L.,; Onungwe, I.,

    2015-01-01

    The problem associated with solid waste management is on the increase both in the industries, urban cities and in the rural areas. In the United States of America, Asia and Europe, there are over hundreds of waste to wealth combustion plants from where solid wastes are incinerated. In Nigeria, amidst the increasing importation of vehicle tyre such plants are scarcely in existence to enhance generation of revenue from waste through the extraction of raw material for the production ...

  16. Assessing radionuclide release and migration during deep geological disposal of bituminized waste: the COLONBO model

    International Nuclear Information System (INIS)

    Full text of publication follows: Bitumen is being used for many years in France as an embedding matrix for the conditioning of low and medium level activity waste resulting from nuclear effluent treatment. Long term management options for this kind of waste include at present deep geological disposal. As a consequence, the COLONBO model has been developed by CEA to predict the long term release of chemical species out of bitumen waste and the subsequent radionuclide migration in the deep geological near field. The COLONBO model is divided into a 'waste package' module, coupled with a 'near field' module. In the first module, the waste package is represented as a bitumen matrix containing an homogeneous dispersion of the salts resulting from the effluent insolubilization treatment. Radionuclides initially present in the waste are thus associated with a mixture of soluble (NaNO3 and Na2SO4) and sparingly soluble (mainly BaSO4) salts. Under leaching, solubilization of water in the bitumen occur at the wasteform surface, followed by water diffusion through the bitumen matrix. Consequently, the soluble salts are progressively dissolved by water accumulation, resulting in a local swelling of the waste package. This swelling induces a local alteration of the diffusive properties of the bitumen matrix, allowing an outward diffusion of the dissolved salts and radionuclides. The resulting migration of chemical species through the storage facility near field is then described in a 'near field' module. In this module, transport is accounted by a simplified reactive diffusion model through porous media, in both saturated or unsaturated conditions. Up to three different zones of the near field can be included, which are described by their respective porosity, hydraulic conductivity, diffusion and retention (Kd) parameters. In the whole system (waste package + near field), water concentration profiles, the position of salt dissolution fronts and chemical species migration are described by water conservation and Fickian diffusion equations related to each area. We will present here the basic model specifications (major parameters, governing equations, numerical implementation, etc.) and some applications of the COLONBO model to performance assessment calculations for typical configurations of deep geological disposal. (authors)

  17. Characterization and modelling of self healing of bituminous materials towards durable asphalt pavement

    NARCIS (Netherlands)

    Qiu, J.; Van de Ven, M.F.C.; Schlangen, H.E.J.G.; Wu, S.; Molenaar, A.A.A.

    2012-01-01

    The traffic volume and the number of heavy vehicles are growing enormously nowadays. There is a need for designing a durable asphalt pavement with innovative technologies. Pavement structures and materials with self healing and self repairing capability are believed to be very useful in such a syste

  18. Acid mine drainage abatement resulting from pressure grouting of buried bituminous mine spoils

    International Nuclear Information System (INIS)

    A 37 acre surface coal mine located in Clinton County, PA, USA, was mined and reclaimed between 1974 and 1977. Buried pyrite-rich pit floor cleanings and tipple refuse were found to be producing severe acid mine drainage. The pyritic material is located in discrete piles or pods in the backfill. The pods and the resulting contaminant plumes were initially defined using geophysical techniques and confirmed by drilling. The approach taken was to use a cementitious grout, composed of fluidized bed combustion ash and water, which would be placed in a manner which would prevent water and oxygen from contacting the pyritic materials. Statistically significant water quality improvements have been noted as a result of the grouting. After four years of post-grouting monitoring, reductions in concentrations of most of the mine drainage parameters range from 40 to 90%. 12 refs., 1 fig., 4 tabs

  19. Evaluation of the fatigue macro-cracking behavior of crumb rubber modified bituminous mixes

    Directory of Open Access Journals (Sweden)

    Moreno-Navarro, F.

    2014-09-01

    Full Text Available The use of crumb rubber modified bitumen (CRMB in asphalt mixes is a road engineering technology that has become increasingly important in recent years. Given the many economic and environmental benefits of this type of binder, the goal is to give CRMB the same level of performance as conventional polymer-modified bitumen. The appearance and propagation of cracks due to fatigue phenomena is one of the most common distresses affecting road pavements. Since crumb rubber enhances the mechanical properties of asphalt mixes, it can provide a viable solution for fatigue cracking. This paper presents the results of a comparative analysis of the fatigue-cracking behavior of asphalt mixtures manufactured with crumb rubber modified bitumen and polymer-modified bitumen.El empleo de betunes modificados con polvo de neumático usado en la fabricación de mezclas bituminosas es una de las técnicas que mayor auge está teniendo en los últimos años en la ingeniería de carreteras. Dadas sus grandes ventajas económicas y ambientales, este tipo de ligantes pretende conseguir prestaciones similares a la de los betunes modificados con polímeros utilizados habitualmente. La aparición de fisuras debido a fenómenos de fatiga es una de las patologías más comunes en firmes de carretera. Debido a las mejoras de las propiedades mecánicas del betún aportadas tras la incorporación de polvo de neumático, las mezclas fabricadas con estos ligantes se postulan como una posible solución a dicho problema. En este artículo se lleva a cabo un análisis comparativo del comportamiento a fisuración por fatiga realizado sobre mezclas bituminosas fabricadas con betún modificado con polvo de neumático y con polímeros.

  20. Rheological behaviour of polymer-modified bituminous mastics : a comparative analysis between physical and chemical modification

    OpenAIRE

    Shivokhin, Maxim; García Morales, Moisés; Partal López, Pedro; Cuadri Vega, Antonio Abad; Gallegos Montes, Críspulo

    2012-01-01

    Mastic, a bitumen/filler blend which naturally forms when bitumen is mixed with aggregates is the actual product used to bind coarse mineral particles in the asphalt mixtures. As a result, the characterisation of mastics is essential to improve the understanding of the response and performance of asphalt concrete pavements. On the other hand, the lack of experimental data concerning the behaviour of mastics and, above all, polymer-modified mastics has been lately claimed. In that sense, this ...

  1. Pneumoconiosis among underground bituminous coal miners in the United States: is silicosis becoming more frequent?

    Energy Technology Data Exchange (ETDEWEB)

    A. Scott Laney; Edward L. Petsonk; Michael D. Attfield [National Institute for Occupational Safety and Health, Morgantown, WV (United States). Division of Respiratory Disease Studies

    2010-10-15

    Epidemiologic reports since 2000 have documented increased prevalence and rapid progression of pneumoconiosis among underground coal miners in the United States. To investigate a possible role of silica exposure in the increase, we examined chest x-rays (CXRs) for specific abnormalities (r-type small opacities) known to be associated with silicosis lung pathology. Underground coal miners are offered CXRs every 5 years. Abnormalities consistent with pneumoconiosis are recorded by National Institute for Occupational Safety and Health (NIOSH) B Readers using the International Labour Office Classification of Radiographs of Pneumoconiosis. CXRs from 1980-2008 of 90,973 participating miners were studied, focusing on reporting of r-type opacities (small rounded opacities 3-10 mm in diameter). Log binomial regression was used to calculate prevalence ratios adjusted for miner age and profusion category. Among miners from Kentucky, Virginia, and West Virginia, the proportion of radiographs showing r-type opacities increased in the 1990s (PR=2.5; 95% CI=1.7-3.7) and after 1999 (PR=4.1; 95% CI=3.0-5.6), compared to the 1980s (adjusted for profusion category and miner age). The prevalence of progressive massive fibrosis in 2000-2008 was also elevated compared to the 1980's (PR=4.4; 95% CI=3.1-6.3) and 1990's (PR=3.8; 95% CI=2.1-6.8) in miners from Kentucky, Virginia, and West Virginia. The increasing prevalence of pneumoconiosis over the past decade and the change in the epidemiology and disease profile documented in this and other recent studies imply that U.S. coal miners are being exposed to excessive amounts of respirable crystalline silica.

  2. Suitability of UK bituminous and Spanish lignitious coals and their blends of two stage liquefaction

    Energy Technology Data Exchange (ETDEWEB)

    Flatman-Fairs, D.P.; Harrison, G. [Staffordshire University, Stoke-on-Trent (United Kingdom). School of Sciences

    1999-11-01

    Liquefaction experiments were carried out in spinning/falling basket autoclaves using samples of Kellingly (UK) and Samca (Spain) coals, and a process derived recycle solvent (PDRS). Hydrocracking experiments were carried out in a bomb type autoclave using sulphided NiMo catalyst. For the dissolution, experiments with the individual coals, the influence of temperature 380, 400 and 420{degree}C, and time 1 or 2 h was considered. For hydrocracking, preliminary experiments were carried out with a Kellingly coal liquid to establish appropriate reaction conditions for the hydrocracking of Kellingly and Samca coal liquid blends. There was some evidence of synergistic activity for conversion to dichloromethane (DCM) soluble material and antagonistic behaviour for conversion to tetrahydrofuran soluble/DCM insoluble material for dissolution of the coal blends, but hydrocracking of the coal liquid blends resulted in additive behaviour. For each of the coals, the extent of dissolution correlated with the extent of desulphurisation. The sulphur contents of the solid residues from dissolution tended to increase with the temperature of dissolution, but their H:C ratios decreased and their calorific values were independent. 12 refs., 7 figs., 3 tabs.

  3. Temperature induced healing in strained bituminous materials observed by atomic force microscopy

    OpenAIRE

    Nahar, S.N.; Schmets, A. J. M.; Scarpas, A.; Schitter, G.

    2013-01-01

    Bitumen is the binder in the composite material named asphalt concrete. Under cyclic mechanical loading of traffic passing over the pavement, eventually damage will initiate in the pavement, leading to eventual structural failure. This damaging process is accelerated by time dependent change of the mechanical properties of asphalt concrete due to ageing mechanisms like oxidation. Bitumen displays spatial heterogeneity at the micrometer scale, which has been observed by atomic force microscopy...

  4. Formation of hydrogen cyanide and ammonia during the gasification of sewage sludge and bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    N. Paterson; Y. Zhuo; D. Dugwell; R. Kandiyoti [Imperial College London, London (United Kingdom). Department of Chemical Engineering

    2005-06-01

    HCN and NH{sub 3} released during the gasification of sewage sludge have been measured during a program of tests with a laboratory-scale spouted-bed gasifier. The data have been compared with results from gasification tests with coal. The effect of altering the bed temperature has been investigated, and the results have been related to reactions involving gaseous N species known to occur in the gasifier. The effect of steam addition on the HCN release has been examined. It has been found that the HCN concentrations in the exit gas increase with the operating temperature, which is thought to indicate increased formation as a primary product of the decomposition of the fuel-N compounds. Increasing the height of the char bed caused a significant reduction in the HCN concentration at the exit, as this promoted the decomposition of HCN to NH{sub 3}. Steam addition caused a rise in the HCN concentration during tests with sewage sludge and a similar effect had previously been reported on the NH{sub 3} concentration during tests with coal. The NH{sub 3} concentration decreased with increasing temperature, and this is thought to reflect the increased rate of the equilibration of NH{sub 3} in the gas phase to form N{sub 2} and H{sub 2}. 18 refs., 4 figs., 5 tabs.

  5. Solid superacid-catalyzed hydroconversion of an extraction residue from Lingwu bituminous coal

    Institute of Scientific and Technical Information of China (English)

    Xiao-Ming Yue; Xian-Yong Wei; Bing Sun; Ying-Hua Wang; Zhi-Min Zong; Zi-Wu Liu

    2012-01-01

    A solid superacid was prepared as a catalyst.The catalyst was characterized by ammonia temperatureprogrammed desorption,surface property measurement,and analyses with scanning electron microscopy and Fourier transform infrared spectrometry.A extraction residue from Lingwu subbituminous coal was subject to non-catalytic and catalytic hydroconversion using cyclohexane as the solvent under pressurized hydrogen at 300 ℃ for 3h.The results show that the total yield of petroleum ether-extractable arenes from catalytic hydroconversion is much higher than that from non-catalytic hydroconversion.The cleavage of Car-Calk bonds in the residue could significantly proceed during catalytic hydroconversion.

  6. Waste to Wealth; The Utilization of Scrap Tyre as Aggregate in Bituminous Mixes for Road Construction

    Directory of Open Access Journals (Sweden)

    Oba, A. L.,

    2015-11-01

    Full Text Available The problem associated with solid waste management is on the increase both in the industries, urban cities and in the rural areas. In the United States of America, Asia and Europe, there are over hundreds of waste to wealth combustion plants from where solid wastes are incinerated. In Nigeria, amidst the increasing importation of vehicle tyre such plants are scarcely in existence to enhance generation of revenue from waste through the extraction of raw material for the production of light weight aggregates, printing ink, paints, shoe polish, dry cell and battery heads. This research paper seeks to utilize vehicle scrap tyre (VST as aggregates in asphaltic mixture by adopting the dry process to evaluate the effect of rubber-bitumen interaction on asphaltic concrete properties; laboratory investigation using 4.75mm, 2.36mm and 0.600mm chunk tyre particle size modified asphalt mixture containing 2%, 4%, 6%, 8% and 10% scrap tyre and 0% tyre content as control mixture. The mixtures were subjected to Marshall Tests where the stability, flow, percentage air void, unit weight, void mineral aggregate, height of specimen and specific gravity were determined. The results obtained shows that as tyre percentage increase the stability, unit weight and specific gravity value decreases. On the other hand, as the tyre content increases, the flow and height of specimen increases while as the tyre content increases the percentage air void and VMA increased for 4.75mm Tyre Particle Size (TPS and 2.36mm TPS while for 0.600mm TPS, reverse is the case. In summary and in comparism with standard specification for road construction material, the Marshall tests conducted on the tyre modified specimens remained intact and by interpretation; material possessing such property indicates good impact resistance when use as surface course in flexible pavement. Conclusively, the use of 10% 4.75mm, 4% 2.36mm or 4% 0.600mm TPS by weight of aggregate in asphaltic concrete is recommended for medium traffic volume pavement which in turn leads to a considerable percentage of sanitation in our cities in terms of reduction in scrap tyre waste management and waste to wealth generation.

  7. XRD and FT–IR investigations of sub-bituminous Assam coals

    Indian Academy of Sciences (India)

    Binoy K Saikia; R K Boruah; P K Gogoi

    2007-08-01

    Two coal samples collected from Makum coal field, Assam, India were studied by XRD and FT–IR techniques. The X-ray diffractogram shows the existence of some crystalline carbons in Assam coals as proven by the appearance of peaks. The radial distribution functional (RDF) method was applied for the determination of structural aspects of the coals. The study indicates that the coals are lignite in type and there is no evidence of graphite-like structures. The maximum in the () plots of function of radial distribution of atoms (FRDA) relates to different distances between carbon atoms of aliphatic chains. The first significant maximum relates to the C–C bond (type C–CH=CH–C), the second maximum relates to the distance between carbon atoms of aliphatic chains that are located across one carbon atom. The curve intensity profiles obtained from FRDA show quite regular molecular packets for this coal. The coals were found to be lignite in nature. FT–IR study shows the presence of aliphatic carbon, C=O and C–O stretching associated with –OH and –NH stretching vibrations. Kaolinite and quartz were also found to be major minerals in Assam coals by FTIR spectroscopy. The difference in intensities of carbonyl groups of the coal samples is likely to relate with the rank.

  8. Hydrogen from the two-stage pyrolysis of bituminous coal/waste plastics mixtures

    Czech Academy of Sciences Publication Activity Database

    Kříž, Vlastimil; Bičáková, Olga

    2011-01-01

    Roč. 36, č. 15 (2011), s. 9014-9022. ISSN 0360-3199 R&D Projects: GA ČR(CZ) GA105/07/1407 Institutional research plan: CEZ:AV0Z30460519 Keywords : hydrogen * two-stage pyrolysis * coal Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 4.054, year: 2011 http://www.sciencedirect.com/science/article/pii/S0360319911007622

  9. Research on Fatigue Properties of Asphalt Pavement on Mix Base%混合式基层沥青路面的疲劳特性分析研究

    Institute of Scientific and Technical Information of China (English)

    彭宏图

    2013-01-01

    According to the 06 standard design methods,AASHTO experiment methods and actual interlayer bonding state,the fatigue properties of three different bituminous pavements of composite base are analyzed in this paper.The results reveal that with the same thickness,the mixed asphalt pavement has a better fatigue life than the semi-rigid base AC pavement.For the purpose of analyzing the sensitivity of the fatigue property,the thickness of the pavement and modulus of graded gravel are also taken into account in three different asphalt pavements of composite.%采用了06版规范方法、考虑实际层间粘接状态的规范方法以及AASH00经验方法对3种类型的混合式基层沥青路面的疲劳特性进行了分析研究,得出了相同厚度的混合式基层沥青路面比半刚性基层沥青路面具有更长的疲劳寿命的结论.并对不同结构层厚度、级配碎石模量对3种类型的混合式基层沥青路面的疲劳特性的敏感性进行了分析.

  10. Novel Sorbent-Based Process for High Temperature Trace Metal Removal

    Energy Technology Data Exchange (ETDEWEB)

    Gokhan Alptekin

    2008-09-30

    The objective of this project was to demonstrate the efficacy of a novel sorbent can effectively remove trace metal contaminants (Hg, As, Se and Cd) from actual coal-derived synthesis gas streams at high temperature (above the dew point of the gas). The performance of TDA's sorbent has been evaluated in several field demonstrations using synthesis gas generated by laboratory and pilot-scale coal gasifiers in a state-of-the-art test skid that houses the absorbent and all auxiliary equipment for monitoring and data logging of critical operating parameters. The test skid was originally designed to treat 10,000 SCFH gas at 250 psig and 350 C, however, because of the limited gas handling capabilities of the test sites, the capacity was downsized to 500 SCFH gas flow. As part of the test program, we carried out four demonstrations at two different sites using the synthesis gas generated by the gasification of various lignites and a bituminous coal. Two of these tests were conducted at the Power Systems Demonstration Facility (PSDF) in Wilsonville, Alabama; a Falkirk (North Dakota) lignite and a high sodium lignite (the PSDF operator Southern Company did not disclose the source of this lignite) were used as the feedstock. We also carried out two other demonstrations in collaboration with the University of North Dakota Energy Environmental Research Center (UNDEERC) using synthesis gas slipstreams generated by the gasification of Sufco (Utah) bituminous coal and Oak Hills (Texas) lignite. In the PSDF tests, we showed successful operation of the test system at the conditions of interest and showed the efficacy of sorbent in removing the mercury from synthesis gas. In Test Campaign No.1, TDA sorbent reduced Hg concentration of the synthesis gas to less than 5 {micro}g/m{sup 3} and achieved over 99% Hg removal efficiency for the entire test duration. Unfortunately, due to the relatively low concentration of the trace metals in the lignite feed and as a result of the

  11. A model combining spectrum standardization and dominant factor based partial least square method for carbon analysis in coal using laser-induced breakdown spectroscopy

    International Nuclear Information System (INIS)

    Quantitative measurement of carbon content in coal is essentially important for coal property analysis. However, quantitative measurement of carbon content in coal using laser-induced breakdown spectroscopy (LIBS) suffered from low measurement accuracy due to measurement uncertainty as well as the matrix effects. In this study, our previously proposed spectrum standardization method and dominant factor based partial least square (PLS) method were combined to improve the measurement accuracy of carbon content in coal using LIBS. The combination model utilized the spectrum standardization method to accurately calculate dominant carbon concentration as the dominant factor, and then applied PLS with full spectrum information to correct residual errors. The combination model was applied to measure the carbon content in 24 bituminous coal samples. Results demonstrated that the combination model can further improve measurement accuracy compared with the spectrum standardization model and the dominant factor based PLS model, in which the dominant factor was calculated using traditional univariate method. The coefficient of determination, root-mean-square error of prediction, and average relative error for the combination model were 0.99, 1.63%, and 1.82%, respectively. The values for the spectrum standardization model were 0.90, 2.24%, and 2.75%, respectively, whereas those for the dominant factor based PLS model were 0.99, 2.66%, and 3.64%, respectively. The results indicate that LIBS has great potential to be applied for the coal analysis. - Highlights: • Spectrum standardization method is utilized to establish a more accurate dominant factor model. • PLS algorithm is applied to further compensate for residual errors using the entire spectrum information. • Measurement accuracy is improved

  12. Major aspects of strategy of hydrogen-base power development with nuclear energy sources

    International Nuclear Information System (INIS)

    Full text: Hydrogen - highly effective and ecologically clean fuel. Large-scale use of hydrogen is mastered in industrial chemical processes and rocket engineering. Manufacture of hydrogen in the world has exceeded 50 MT H2 (6.4 EJ) and quickly grows. In the report the concept of Nuclear-hydrogen power (NHP) as strategy of production and use of hydrogen on base of 'clean' technologies and, first of all, modern innovative high-temperature nuclear energy source such as GT-MHR, modified under hydrogen production application is considered with steam reforming of methane (SRM). The increase of a nuclear energy share in a global energy balance is capable essentially to affect structure of on organic fuel consumption, and, hence, on resulting parameters on hydrocarbon world flows and CO2 emissions. Under the various forecasts (IIASA, IAEA, IEA, EPRI etc.) in 21 century the sharp growth of demand hydrogen is expected in connection with transition of various base technological branches to mainly intensive methods of qualitative products output with increase of processing depth of petroleum industry, greater release of ammonia and methanol, refinery processing (for example, from heavy oil or bituminous sand) or synthetic (first of all, - from coal) liquid fuel, increase of direct production of qualitative sponge iron etc. At the same time, greatest contribution to perspective growth of world demand on hydrogen is necessary to expect from a vehicle sector and systems of the dispersed power supply, in which the hydrogen acts as energy carrier, capable to collect and to be transported similarly to natural gas, but not having, as against methane, restrictions on resource base and not having effluents of greenhouse gases in an atmosphere. For the various scripts of global economy development and parameters of an expected level of power supply forecasts of market potential estimation are changing from low volumes of hydrogen production (in 1.5-2 times exceeding a present

  13. Export market potential for Alaskan and Western US coals

    International Nuclear Information System (INIS)

    Major utilization trends may create opportunity for dramatic expansion of Alaska's coal exports from a huge ultra-low sulfur coal resource base. Markets are expected to open up in the Pacific Basin for sub-bituminous and bituminous steam coals from Alaska to include not only run-of-mine coals but also product streams from beneficiation technologies. Market considerations aside, deficiencies in physical infrastructure and an unresolved resource ownership issue are the principal impediments at this time to property development

  14. Touch BASE

    CERN Multimedia

    Antonella Del Rosso

    2015-01-01

    In a recent Nature article (see here), the BASE collaboration reported the most precise comparison of the charge-to-mass ratio of the proton to its antimatter equivalent, the antiproton. This result is just the beginning and many more challenges lie ahead.   CERN's AD Hall, where the BASE experiment is set-up. The Baryon Antibaryon Symmetry Experiment (BASE) was approved in June 2013 and was ready to take data in August 2014. During these 14 months, the BASE collaboration worked hard to set up its four cryogenic Penning traps, which are the heart of the whole experiment. As their name indicates, these magnetic devices are used to trap antiparticles – antiprotons coming from the Antiproton Decelerator – and particles of matter – negative hydrogen ions produced in the system by interaction with a degrader that slows the antiprotons down, allowing scientists to perform their measurements. “We had very little time to set up the wh...

  15. Monetary base

    OpenAIRE

    Richard G. Anderson

    2006-01-01

    This brief essay is a working draft of an article in preparation for the forthcoming International Encyclopedia of the Social Sciences, 2nd ed., examining the role of the monetary base in monetary economics and monetary policymaking. Comments are welcome.

  16. Web based foundry knowledge base

    Directory of Open Access Journals (Sweden)

    A. Stawowy

    2009-01-01

    Full Text Available The main assumptions and functions of proposed Foundry Knowledge Base (FKB are presented in this paper. FKB is a framework forinformation exchange of casting products and manufacturing methods. We use CMS (Content Management System to develope andmaintain our web-based system. The CastML – XML dialect developed by authors for description of casting products and processes – isused as a tool for information interchange between ours and outside systems, while SQL is used to store and edit knowledge rules and alsoto solve the basic selection problems in the rule-based module. Besides the standard functions (companies data, news, events, forums and media kit, our website contains a number of nonstandard functions; the intelligent search module based on expert system is the main advantage of our solution. FKB is to be a social portal which content will be developed by foundry community.

  17. The Impact of the Bituminous Coal Combustion from the Thermoelectric Power Plant from Paroseni on the Environment of Jiu Valley

    Directory of Open Access Journals (Sweden)

    Mircea Rebrisoreanu

    2002-04-01

    Full Text Available The Jiu Valley Basin is one of the most important coal mining areas in Romania. Other industries, including a power plant, are also well developed in this area. Therefore, pollution is very high. One of the most polluted environmental compounds is the air. High mountains surround the Jiu Valley, which makes difficult the air refreshing. For this reason, it is very important to discuss the air pollution and especially that produced by dust. Since the industrial companies are concentrated in a small area, it is very difficult to identify and prosecute the polluting one. The present paper aims to identify the sources of air pollution, especially among the mining companies, because the power plant is considered the most important polluting agent in this area.

  18. Down-scaling of bituminous coal mining, restructuring of steel works and heavy engineering in the Ostrava region

    Czech Academy of Sciences Publication Activity Database

    Klusáček, Petr

    2005-01-01

    Roč. 13, č. 2 (2005), s. 3-12. ISSN 1210-8812 R&D Projects: GA AV ČR(CZ) IBS3086005 Institutional research plan: CEZ:AV0Z30860518 Keywords : Ostrava region * restructuring * steemaking and heavy industry * downscaling of coal- mining Subject RIV: DE - Earth Magnetism, Geodesy, Geography

  19. Superpave沥青混合料路用性能的研究%Study on Superpave Bituminous Mixture Performance

    Institute of Scientific and Technical Information of China (English)

    李文瑛; 彭波; 戴经梁

    2003-01-01

    通过试验研究,系统分析了Superpave沥青混合料的路用性能,并与密级配沥青混凝土进行了对比分析.结果表明,Superpave沥青混合料是一种性能优良的沥青混合料.

  20. Lung cancer risk of low-level exposures to alpha emitters: critical reappraisal and experiments based on a new cytodynamic model

    Energy Technology Data Exchange (ETDEWEB)

    Bogen, Kenneth T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    1999-02-20

    Ecologic U.S. county data suggest negative associations between residential radon exposure and lung cancer mortality (LCM)-inconsistent with clearly positive associations revealed by occupational data on individual miners, but perhaps explained by competing effects of cell killing vs. mutations in alpha-exposed bronchial epithelium. To assess the latter possibility, a biologically based "cytodynamic 2-stage" (CD2) cancer-risk model was fit to combined 1950-54 age- specific person-year data on lung cancer mortality (LCM) in white females of age 40+ y in 2,821 U.S. counties (-90% never-smokers), and in 5 cohorts of underground miners who never smoked. New estimates of household annual average radon exposure in U.S. counties were used, which were found to have a significant negative ecologic association with 1950-54 LCM in U.S. white females, adjusted for age and all subsets of two among 21 socioeconomic, climatic and other factors considered. A good CD2 fit was obtained to the combined residential/miner data, using biologically plausible parameter values. Without further optimization, the fit also predicted independent inverse dose-rate effects shown (for the first time) to occur in nonsmoking miners. Using the same U.S. county-level LCM data, a separate study revealed a positive ecologic association between LCM and bituminous coal use in the U.S., in agreement with epidemiological data on LCM in women in China. The modeling results obtained are consistent with the CD2-based hypothesis that residential radon exposure has a nonlinear U-shaped relation to LCM risk, and that current linear no-threshold extrapolation models substantially overestimate such risk. A U-shaped dose-response corresponds to a CD2-model prediction that alpha radiation kills more premalignant cells than it generates at low exposure levels, but not at higher levels. To test this hypothesis, groups of Japanese medaka (ricefish minnows) were exposed for 10 to 14 weeks to different concentrations of

  1. Foundation: Transforming data bases into knowledge bases

    Science.gov (United States)

    Purves, R. B.; Carnes, James R.; Cutts, Dannie E.

    1987-01-01

    One approach to transforming information stored in relational data bases into knowledge based representations and back again is described. This system, called Foundation, allows knowledge bases to take advantage of vast amounts of pre-existing data. A benefit of this approach is inspection, and even population, of data bases through an intelligent knowledge-based front-end.

  2. Development of a Novel Gas Pressurized Process-Based Technology for CO2 Capture from Post-Combustion Flue Gases Preliminary Year 1 Techno-Economic Study Results and Methodology for Gas Pressurized Stripping Process

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Shiaoguo

    2013-03-01

    Under the DOE’s Innovations for Existing Plants (IEP) Program, Carbon Capture Scientific, LLC (CCS) is developing a novel gas pressurized stripping (GPS) process to enable efficient post-combustion carbon capture (PCC) from coal-fired power plants. A technology and economic feasibility study is required as a deliverable in the project Statement of Project Objectives. This study analyzes a fully integrated pulverized coal power plant equipped with GPS technology for PCC, and is carried out, to the maximum extent possible, in accordance to the methodology and data provided in ATTACHMENT 3 – Basis for Technology Feasibility Study of DOE Funding Opportunity Number: DE-FOA-0000403. The DOE/NETL report on “Cost and Performance Baseline for Fossil Energy Plants, Volume 1: Bituminous Coal and Natural Gas to Electricity (Original Issue Date, May 2007), NETL Report No. DOE/NETL-2007/1281, Revision 1, August 2007” was used as the main source of reference to be followed, as per the guidelines of ATTACHMENT 3 of DE-FOA-0000403. The DOE/NETL-2007/1281 study compared the feasibility of various combinations of power plant/CO2 capture process arrangements. The report contained a comprehensive set of design basis and economic evaluation assumptions and criteria, which are used as the main reference points for the purpose of this study. Specifically, Nexant adopted the design and economic evaluation basis from Case 12 of the above-mentioned DOE/NETL report. This case corresponds to a nominal 550 MWe (net), supercritical greenfield PC plant that utilizes an advanced MEAbased absorption system for CO2 capture and compression. For this techno-economic study, CCS’ GPS process replaces the MEA-based CO2 absorption system used in the original case. The objective of this study is to assess the performance of a full-scale GPS-based PCC design that is integrated with a supercritical PC plant similar to Case 12 of the DOE/NETL report, such that it corresponds to a nominal 550 MWe

  3. INVOLUTIVE BASES UNDER COMPOSITION

    Institute of Scientific and Technical Information of China (English)

    Zailiang TANG

    2007-01-01

    In this paper, the behaviors of involutive bases under composition operation are studied.For two kinds of involutive bases, i.e., Pommaret bases, Janet bases, we study their behavior problems under composition. Some further problems are also proposed.

  4. Nuclear asphalt content gauge study. Research report (Final)

    International Nuclear Information System (INIS)

    This research ascertains if the Troxler Model 3241 Gauge could accurately determine the asphalt content of bituminous-concrete mixtures by nuclear means. The study was divided into three phases. Phase I was conducted in the Central Laboratory where a series of controlled tests were performed for variables that may effect the gauge's asphalt-content determinations. Phase II evolved into a cooperative study between the Maryland State Highway Administration (SHA) and several bituminous concrete producers. Phase III was to report the findings of the study and make a recommendation on the overall practical application of the gauge. The results indicate that the gauge can accurately determine asphalt contents on normal surface and base bituminous mixtures

  5. Hybrid direct carbon fuel cell anode processes investigated using a 3-electrode half-cell setup

    DEFF Research Database (Denmark)

    Deleebeeck, Lisa; Arenillas, A.; Menendez, J.A.;

    2015-01-01

    anthracite and bituminous coals, as well as carbon black, were tested, revealing similar open circuit potential and activation energies in mixed 96-4vol% N2-CO2 and 50-50vol% CO-CO2 environments between 700 and 800°C. Bituminous coal showed the highest activity, likely associated to a high O/C ratio...... and hydrogen content. Based on acquired data, a reaction scheme was proposed for processes at the working electrode, including the role of bubble formation in the vicinity of the electrochemically active solid/molten medium interface....

  6. Intrusion resistant underground structure (IRUS) : design and operations

    International Nuclear Information System (INIS)

    The safety case for the IRUS low-level radioactive waste disposal facility is based on the fact that IRUS will contain three specific types of wastes only. The types of these wastes are baled wastes, bituminized incinerator ash, and bituminized reverse osmosis concentrate. IRUS will be a below-ground vault consisting of an open bottom reinforced-concrete structure (approximate dimensions 30m x 20m x 8m) with a reinforced-concrete roof. This paper covers the vault design and construction and operational features. 2 tabs

  7. A dynamic knowledge base based search engine

    Institute of Scientific and Technical Information of China (English)

    WANG Hui-jin; HU Hua; LI Qing

    2005-01-01

    Search engines have greatly helped us to find thedesired information from the Intemet. Most search engines use keywords matching technique. This paper discusses a Dynamic Knowledge Base based Search Engine (DKBSE), which can expand the user's query using the keywords' concept or meaning. To do this, the DKBSE needs to construct and maintain the knowledge base dynamically via the system's searching results and the user's feedback information. The DKBSE expands the user's initial query using the knowledge base, and returns the searched information after the expanded query.

  8. Knowledge Based Strategies for Knowledge Based Organizations

    Directory of Open Access Journals (Sweden)

    Madalina Cristina Tocan

    2012-12-01

    Full Text Available In the present, we can observe that a new economy is arising. It is an economy based on knowledge and ideas, in which the key factor for prosperity and for creation of the new jobs is the knowledge capitalization. Knowledge capitalization, intellectual capital, obtaining prosperity in the market economy imposes a new terminology, new managerial methods and techniques, new technologies and also new strategies. In other words, knowledge based economy, as a new type of economy; impose a new type of management- knowledge based management and a new type of enterprise-knowledge based enterprise.Taking in consideration these predictable evolutions, this paper will try to present: • The main ideas of the researches the field of the knowledge based economy • The characteristics and principles of the knowledge based organizations and knowledge based management • The challenges and opportunities for knowledge based organizations.The first part of the paper will present the principles of the new economy- knowledge base economy, the essential and interrelated elements necessary to build and to implement a strategy in a knowledge economy and the opportunities and challenges to the countries as they seek to build regionally and globally competitive knowledge-based economies.The second part of the paper will present the characteristics of the knowledge based organizations, the principles and characteristics of their management. For many organizations, knowledge management is a relatively new concept, because they are discovering the knowledge value in their operations. Many firms have undertaken formal and informal knowledge management initiatives designed to improve process performance, increase customer responsiveness and spur innovation. But while some organizations have reaped significant benefits from their investment in knowledge efforts, others have run into noteworthy challenges.

  9. Team-Based Learning

    Science.gov (United States)

    Michaelsen, Larry K.; Sweet, Michael

    2011-01-01

    Team-based learning (TBL), when properly implemented, includes many, if not all, of the common elements of evidence-based best practices. To explain this, a brief overview of TBL is presented. The authors examine the relationship between the best practices of evidence-based teaching and the principles that constitute team-based learning. (Contains…

  10. Solid Base Catalysis

    CERN Document Server

    Ono, Yoshio

    2011-01-01

    The importance of solid base catalysts has come to be recognized for their environmentally benign qualities, and much significant progress has been made over the past two decades in catalytic materials and solid base-catalyzed reactions. The book is focused on the solid base. Because of the advantages over liquid bases, the use of solid base catalysts in organic synthesis is expanding. Solid bases are easier to dispose than liquid bases, separation and recovery of products, catalysts and solvents are less difficult, and they are non-corrosive. Furthermore, base-catalyzed reactions can be performed without using solvents and even in the gas phase, opening up more possibilities for discovering novel reaction systems. Using numerous examples, the present volume describes the remarkable role solid base catalysis can play, given the ever increasing worldwide importance of "green" chemistry. The reader will obtain an overall view of solid base catalysis and gain insight into the versatility of the reactions to whic...

  11. Case Base Maintenance Approach.

    OpenAIRE

    Haouchine, Mohamed-Karim; Chebel-Morello, Brigitte; Zerhouni, Noureddine

    2007-01-01

    Case base Maintenance is an active Case Based Reasoning research area. The main stream focuses on the method for reducing the size of the case-base while maintaining case-base competence. This paper gives an overview of these works, and proposes a case deletion strategy based on competence criteria using a novel approach. The proposed method, even if inspired from existing literature, combines an algorithm with a Competence Metric (CM). A series of tests are conducted using two standards data...

  12. Development of nanomodifiers and research into their influence on the properties of bituminous binders Разработка наномодификаторов и исследование их влияния на свойства битумных вяжущих веществ

    Directory of Open Access Journals (Sweden)

    Inozemtsev Sergey Sergeevich

    2013-09-01

    Full Text Available Nine types of nanomodifiers designated for asphalt binder are considered in the article. Three mineral material types of are considered, including dolomite powder MP-1, diatomite and activated silica sand. As the second component cotton oil, synthetic rubber and a colloid solution of ferric (III hydroxide and silica acid are selected. The results of the study disclose the influence of nanomodifiers on needle penetration depth at 0 °C and 25 °C, as well as the softening temperature, brittleness properties and stability after aging. The penetration depth is a criterion of the ability of the bitumen to resist mechanical stress, while brittleness and / or softening are the criteria of its ability to resist temperature. The generalized effectiveness criterion of bitumen modifiers is also taken into account. The generalized effectiveness criterion of nanomodifiers was revealed based on the obtained data. One of the most effective modifiers is diatomite with a colloid solution of ferric hydroxide (III and silica acid. Dolomite powder with sol and diatomite with synthetic rubber (layer 70 nm are promising methods of modification, though they require optimization in terms of their technology and formulations.Рассмотрено несколько вариантов наномодификаторов для битумного вяжущего, синтез которых заключается в нанесении на минеральные компоненты (минеральный порошок МП-1, диатомит, активированный кварцевый песок нанометрового слоя госсиполовой смолы, каучука СКДН или двухкомпонентного золя. Приведены результаты исследования влияния разработанных наномодификаторов на свойства битумного вяжущего. На

  13. Knowledge Based Strategies for Knowledge Based Organizations

    OpenAIRE

    Madalina Cristina Tocan

    2012-01-01

    In the present, we can observe that a new economy is arising. It is an economy based on knowledge and ideas, in which the key factor for prosperity and for creation of the new jobs is the knowledge capitalization. Knowledge capitalization, intellectual capital, obtaining prosperity in the market economy imposes a new terminology, new managerial methods and techniques, new technologies and also new strategies. In other words, knowledge based economy, as a new type of economy; impose a new type...

  14. Construction Package No. 2. Final Earthwork and Roadwork (RADL Item 7-28)

    Energy Technology Data Exchange (ETDEWEB)

    1980-07-01

    The final earthwork, aggregate surfacing, roadwork and paving for the Barstow Solar Pilot Plant are presented. The work consisted of applying weed killer to surfaces to be paved, constructing bituminous pavements, restoring existing compacted aggregate base roadways, and stripping and removing existing grade from the core area for compacted aggregate surfacing.

  15. Uruguay minerals fuels

    International Nuclear Information System (INIS)

    In this report the bases for the development of the necessary works of prospection are exposed on mineral fuels of Uruguay. We have taken the set from: coal, lutitas bituminous, uranium, petroleum and disturbs. In all the cases we have talked about to the present state of the knowledge and to the works that we considered necessary to develop in each case

  16. Use of molten inorganic salts as coolants in the nuclear power sector - salt of the Earth and light of the world

    International Nuclear Information System (INIS)

    The following topics are highlighted in this overview: Molten fluoride based heat transfer system (Hydrogen production by thermochemical processes; Extraction and processing of bituminous sands and oil shales; Brayton cycle for a more efficient power generation); Advanced high-temperature nuclear reactor; Liquid salt-cooled fast reactor; Molten salt reactor; and Thermonuclear hydrogen fusion. (P.A.)

  17. VectorBase

    Data.gov (United States)

    U.S. Department of Health & Human Services — VectorBase is a Bioinformatics Resource Center for invertebrate vectors. It is one of four Bioinformatics Resource Centers funded by NIAID to provide web-based...

  18. Beyond Zero Based Budgeting.

    Science.gov (United States)

    Ogden, Daniel M., Jr.

    1978-01-01

    Suggests that the most practical budgeting system for most managers is a formalized combination of incremental and zero-based analysis because little can be learned about most programs from an annual zero-based budget. (Author/IRT)

  19. Mobile Inquiry Based Learning

    NARCIS (Netherlands)

    Specht, Marcus

    2012-01-01

    Specht, M. (2012, 8 November). Mobile Inquiry Based Learning. Presentation given at the Workshop "Mobile inquiry-based learning" at the Mobile Learning Day 2012 at the Fernuniversität Hagen, Hagen, Germany.

  20. "Education-based Research"

    DEFF Research Database (Denmark)

    Degn Johansson, Troels

    This paper lays out a concept of education-based research-the production of research knowledge within the framework of tertiary design education-as an integration of problem-based learning and research-based education. This leads to a critique of reflective practice as the primary way to facilitate...... learning at this level, a discussion of the nature of design problems in the instrumentalist tradition, and some suggestions as to how design studies curricula may facilitate education-based research....

  1. The ground based plan

    International Nuclear Information System (INIS)

    The paper presents a report of ''The Ground Based Plan'' of the United Kingdom Science and Engineering Research Council. The ground based plan is a plan for research in astronomy and planetary science by ground based techniques. The contents of the report contains a description of:- the scientific objectives and technical requirements (the basis for the Plan), the present organisation and funding for the ground based programme, the Plan, the main scientific features and the further objectives of the Plan. (U.K.)

  2. Problem Based Learnig

    OpenAIRE

    Kolmos, Anette; Kuru, Selahattin; Hansen, Hans; Eskil, Taner; Podesta, Luca; Fink, Flemming; Graaff, Erik de; Uwe Wolff, Jan; Soylu, Ahmet

    2007-01-01

    This report discuss Problem-Based and Project-Based Learning (PBL) as an approach to meeting the demand for the educational requirements of the next generation engineering graduates. The report is prepared as the final report of the Special Interest Group (SIG) B5 of the Erasmus Thematic Network Project TREE (Teaching and Research in Engineering Education) on Problem- Based and Project-Based Learning. In engineering education there is a shift in emphasis from professional skill...

  3. Stolen Base Physics

    Science.gov (United States)

    Kagan, David

    2013-01-01

    Few plays in baseball are as consistently close and exciting as the stolen base. While there are several studies of sprinting, the art of base stealing is much more nuanced. This article describes the motion of the base-stealing runner using a very basic kinematic model. The model will be compared to some data from a Major League game. The…

  4. Convergent Filter Bases

    OpenAIRE

    Coghetto Roland

    2015-01-01

    We are inspired by the work of Henri Cartan [16], Bourbaki [10] (TG. I Filtres) and Claude Wagschal [34]. We define the base of filter, image filter, convergent filter bases, limit filter and the filter base of tails (fr: filtre des sections).

  5. Pipe reactor gasification studies of a south african bituminous coal blend. Part 1 - Carbon and volatile matter behaviour as function of feed coal particle size reduction

    OpenAIRE

    Waanders, Frans

    2009-01-01

    The Sasol-Lurgi fixed-bed dry-bottom (FBDB) MKIV gasifiers are proven to be robust as far as acceptable coal properties are concerned, in particular its ability to accommodate a range of particle size distributions (PSD) fractions. Over the years, the findings from a number of studies conducted at Sasol have played a key role in the optimization of the Sasol-Lurgi gasifiers as far as the limited amount of coal preparation by crushing and screening is concerned. The continued optimization effo...

  6. 由二种烟煤制备碳纳米管的探索性研究%CARBON NANOTUBES FROM TWO BITUMINOUS COALS

    Institute of Scientific and Technical Information of China (English)

    邱介山; 胡德生; 等

    2001-01-01

    以一种中国烟煤和一种新西兰烟煤为原料,采用电弧等离子体法制备碳纳米管.碳纳米管及其副产物富勒烯烟灰的表征采用扫描电镜(SEM)和红外光谱( FT-IR)等技术.结果表明:电弧放电时的缓冲气体压力对碳纳米管的产率影响很大;在一定的缓冲气压下电极间电流和电极间距各存在一最佳值.在He气压力为0.0665MPa、工作电流为40A条件下进行电弧放电,阴极上棒状沉积物的内芯中碳纳米管含量高达75%以上.基于实验结果,讨论了以煤为原料用电弧等离子体法制备碳纳米管过程中的工艺参数对碳纳米管生长的影响.

  7. Effect of various catalysts on the chemical structure of oils and asphaltenes obtained from the hydroliquefaction of a highly volatile bituminous coal

    Energy Technology Data Exchange (ETDEWEB)

    Cebolla, V.L.; Diack, M.; Oberson, M.; Bacaud, R.; Cagniant, D.; Nickel-Pepin-Donat, B. (Universite de Metz, Metz (France))

    1991-07-01

    The catalysts studied were aerosols of SiO{sub 2}, Fe{sub 2}O{sub 3}, MoO{sub 3} and Ni-Mo/Al{sub 2}O{sub 3}. The hydroliquefaction runs at 350, 400 and 430{degree}C, in the presence of tetralin and sulfur, were evaluated by solvent extractions, hydrogen consumption and structural analysis of the isolated oil and asphaltene fractions. At 350 {degree}C, a clear influence of the catalyst on the extraction yields is observed. This effect disappears at higher temperatures. Nevertheless, hydrogen consumption from gas or solvent is affected by the nature of the catalyst at a given temperature. The influence of the catalyst is also confirmed by electron spin resonance study of the stable radicals of the tetrahydrofuran insoluble fractions. After elimination of tetralin, the structural analyses were carried out by gas chromatography (oils), size exclusion chromatography (oils and asphaltenes) and extrography (raw hydroliquefaction products). The oils obtained with sulfided Fe{sub 2}O{sub 3} or MoO{sub 3} contained significantly more two-ringed aromatic compounds than oils obtained with the other catalysts or without added catalyst. No significant influence of the catalyst at a given temperature on the oils and asphaltenes is observed by size exclusion chromatography. In contrast, a large temperature effect is evidenced for each fraction, independently of the nature of the catalyst. 38 refs., 7 figs., 6 tabs.

  8. Investigation of pyrite as a contributor to slagging in eastern bituminous coals. Quarterly progress report 9, October 1-December 31, 1983

    Energy Technology Data Exchange (ETDEWEB)

    Bryers, R.W.

    1984-06-01

    The objective of this program is to examine slags formed as a result of firing coals with varying concentration levels, size distribution, and orientation of pyrite with regard to mineral matter in the coal in a laboratory furnace. The program tasks are: (1) selection of eight candidate coals; (2) chemical characterization of the coal samples and identification of the pyrite size, distribution, and orientation with respect to other mineral matter and concentration levels; (3) testing of the candidate coals in a laboratory furnace; (4) chemical and physical characterization of the slag and fly ash samples created by the impurities in the coal sample; (5) influence of coal beneficiation on furnace slagging; and (6) analysis of data and identification of parameters influencing the contribution of pyrite to slagging problems. Washing of the Upper Freeport coal from Indiana County, Pennsylvania, was completed by the last quarter of 1983. The washed product was characterized for mineral content, and a combustion test was performed. Kentucky No. 9 from Henderson County, Kentucky, selected as the sixth coal to be investigated, was characterized using size and gravity fractionation techniques and was combusted in the laboratory furnace to evaluate its slagging and fouling potential. The remaining two coals to be characterized and combusted were identified as Illinois No. 5 and Lower Kittanning from Clarion County, Pennsylvania. 80 figures, 27 tables.

  9. BITUMINOUS MIX RESPONSE TO PLASTIC DEFORMATIONS: COMPARISON OF THE SPANISH NLT-173 AND UNE-EN 12697-22 WHEEL-TRACKING TESTS

    Directory of Open Access Journals (Sweden)

    GEMA GARCÍA-TRAVÉ

    2012-01-01

    Full Text Available La formación de roderas es uno de los mayores deterioros que se producen en los firmes flexibles, lo que ocasiona la pérdida de regularidad superficial que repercute de forma negativa en la calidad del servicio prestado a los usuarios. Existen distintos ensayos de laboratorio que permiten evaluar las deformaciones plásticas producidas en las capas del pavimento, entre ellos podemos destacar los ensayos de simulación. El objetivo de esta investigación es analizar el comportamiento de una mezcla bituminosa en caliente frente a deformaciones plásticas, mediante dos métodos de ensayo diferentes; ensayo en pista de laboratorio de acuerdo a la normativa española NLT-173 y el ensayo de rodadura UNE-EN 12697-22 (ensayo obligatorio tras la entrada en vigor del Marcado CE de mezclas bituminosas en 2008. La finalidad última de este artículo es formular una propuesta de modificación de la normativa española (PG-3 sobre los límites exigibles en éste último ensayo.

  10. Evaluation of co-cokes from bituminous coal with vacuum resid or decant oil, and evaluation of anthracites, as precursors to graphite

    Science.gov (United States)

    Nyathi, Mhlwazi S.

    2011-12-01

    Graphite is utilized as a neutron moderator and structural component in some nuclear reactor designs. During the reactor operaction the structure of graphite is damaged by collision with fast neutrons. Graphite's resistance to this damage determines its lifetime in the reactor. On neutron irradiation, isotropic or near-isotropic graphite experiences less structural damage than anisotropic graphite. The degree of anisotropy in a graphite artifact is dependent on the structure of its precursor coke. Currently, there exist concerns over a short supply of traditional precursor coke, primarily due to a steadily increasing price of petroleum. The main goal of this study was to study the anisotropic and isotropic properties of graphitized co-cokes and anthracites as a way of investigating the possibility of synthesizing isotropic or near-isotropic graphite from co-cokes and anthracites. Demonstrating the ability to form isotropic or near-isotropic graphite would mean that co-cokes and anthracites have a potential use as filler material in the synthesis of nuclear graphite. The approach used to control the co-coke structure was to vary the reaction conditions. Co-cokes were produced by coking 4:1 blends of vacuum resid/coal and decant oil/coal at temperatures of 465 and 500 °C for reaction times of 12 and 18 hours under autogenous pressure. Co-cokes obtained were calcined at 1420 °C and graphitized at 3000 °C for 24 hours. Optical microscopy, X-ray diffraction, temperature-programmed oxidation and Raman spectroscopy were used to characterize the products. It was found that higher reaction temperature (500 °C) or shorter reaction time (12 hours) leads to an increase in co-coke structural disorder and an increase in the amount of mosaic carbon at the expense of textural components that are necessary for the formation of anisotropic structure, namely, domains and flow domains. Characterization of graphitized co-cokes showed that the quality, as expressed by the degree of graphitization and crystallite dimensions, of the final product is dependent on the nature of the precursor co-coke. The methodology for studying anthracites was to select two anthracites on basis of rank, PSOC1515 being semi-anthracite and DECS21 anthracite. The selected anthracites were graphitized, in both native and demineralized states, under the same conditions as co-cokes. Products obtained from DECS21 showed higher degrees of graphitization and larger crystallite dimensions than products obtained from PSOC1515. Demineralization of anthracites served to increase the degree of graphitization, indicating that the minerals contained in these anthracites have no graphitization-enhancing ability. A larger crystallite length for products obtained from native versions, compared to demineralized versions, was attributed to a formation and decomposition of a silicon carbide during graphitization of native versions. In order to examine the anisotropic and isotropic properties, nuclear-grade graphite samples obtained from Oak Ridge National Laboratory (ORNL) and commercial graphite purchased from Fluka were characterized under similar conditions as graphitized co-cokes and anthracites. These samples served as representatives of "two extremes", with ORNL samples being the isotropic end and commercial graphite being the anisotropic end. Through evaluating relationships between structural parameters, it was observed that graphitized co-cokes are situated, structurally, somewhere between the "two extremes", whereas graphitized anthracites are closer to the anisotropic end. Basically, co-cokes have a better potential than anthracites to transform to isotropic or near-isotropic graphite upon graphitization. By co-coking vacuum resid/coal instead of decant oil/coal or using 500 °C instead of 465 °C, a shift away from commercial graphite towards ORNL samples was attained. Graphitizing a semi-anthracite or demineralizing anthracites before graphitization also caused a shift towards ORNL samples.

  11. Explosion characteristics of pulverised torrefied and raw Norway spruce (Picea abies) and Southern pine (Pinus palustris) in comparison to bituminous coal

    International Nuclear Information System (INIS)

    Pre-treatments, such as torrefaction, can improve biomass fuels properties. Dedicated and coal co-firing plants, in which pulverised biomass and torrefied biomass can be used, are exposed to explosion hazards during handling, storage and transport from the mills to the boiler. Data on the explosion characteristics of biomass and torrefied biomass are scarce. This study presents explosion characteristics (maximum explosion pressure, deflagration index and minimum explosible concentration) of two torrefied wood samples and compares their reactivity to that of their corresponding untreated biomass materials and to a sample of Kellingley coal. Torrefied biomass samples showed higher reactivity, overpressures were around 9 bar (0.9 MPa, 1 bar = 105 Pa) for all biomass samples irrespective of size or sample composition. Derived laminar burning velocities ranged between 0.1–0.12 m s−1, and were therefore similar to that of coal (0.12 m s−1). The differences in explosion reactivity influence the design of explosion protection measures and can be used to introduce suitable modifications for safe operations with torrefied biomass. - Highlights: • Explosion characteristics were measured for two torrefied biomass samples. • Properties were compared to those of coal and corresponding untreated biomass. • Maximum explosion overpressures were similar for all biomass at about 9 bar. • Torrefied biomass was more reactive than coal and untreated biomass. • Biomass explosion data can be used to design better safety systems

  12. Distribution and Fate of Mercury in Pulverized Bituminous Coal-Fired Power Plants in Coal Energy-Dominant Huainan City, China.

    Science.gov (United States)

    Chen, Bingyu; Liu, Guijian; Sun, Ruoyu

    2016-05-01

    A better understanding on the partitioning behavior of mercury (Hg) during coal combustion in large-scale coal-fired power plants is fundamental for drafting Hg-emission control regulations. Two large coal-fired utility boilers, equipped with electrostatic precipitators (ESPs) and a wet flue gas desulfurization (WFGD) system, respectively, in coal energy-dominant Huainan City, China, were selected to investigate the distribution and fate of Hg during coal combustion. In three sampling campaigns, we found that Hg in bottom ash was severely depleted with a relative enrichment (RE) index coal. We estimated that Hg emissions in all Huainan coal-fired power plants varied from 1.8 Mg in 2003 to 7.3 Mg in 2010. PMID:26883032

  13. Mineralogical and elemental composition of fly ash from pilot scale fluidised bed combustion of lignite, bituminous coal, wood chips and their blends

    Energy Technology Data Exchange (ETDEWEB)

    Nikolaos Koukouzas; Jouni Hamalainen; Dimitra Papanikolaou; Antti Tourunen; Timo Jantti [Institute for Solid Fuels Technology and Applications, Ptolemais (Greece). Centre for Research and Technology Hellas

    2007-09-15

    The chemical and mineralogical composition of fly ash samples collected from different parts of a laboratory and a pilot scale CFB facility has been investigated. The fabric filter and the second cyclone of the two facilities were chosen as sampling points. The fuels used were Greek lignite (from the Florina basin), Polish coal and wood chips. Characterization of the fly ash samples was conducted by means of X-ray fluorescence (XRF), inductive coupled plasma-optical emission spectrometry (ICP-OES), thermogravimetric analysis (TGA), particle size distribution (PSD) and X-ray diffraction (XRD). According to the chemical analyses the produced fly ashes are rich in CaO. Moreover, SiO{sub 2} is the dominant oxide in fly ash with Al{sub 2}O{sub 3} and Fe{sub 2}O{sub 3} found in considerable quantities. Results obtained by XRD showed that the major mineral phase of fly ash is quartz, while other mineral phases that are occurred are maghemite, hematite, periclase, rutile, gehlenite and anhydrite. The ICP-OES analysis showed rather low levels of trace elements, especially for As and Cr, in many of the ashes included in this study compared to coal ash from fluidised bed combustion in general. 23 refs., 3 figs., 5 tabs.

  14. Weak mutually unbiased bases

    International Nuclear Information System (INIS)

    Quantum systems with variables in Z(d) are considered. The properties of lines in the Z(d)xZ(d) phase space of these systems are studied. Weak mutually unbiased bases in these systems are defined as bases for which the overlap of any two vectors in two different bases is equal to d−1/2 or alternatively to one of the d−1/2i, 0 (where di is a divisor of d apart from d, 1). They are designed for the geometry of the Z(d)xZ(d) phase space, in the sense that there is a duality between the weak mutually unbiased bases and the maximal lines through the origin. In the special case of prime d, there are no divisors of d apart from 1, d and the weak mutually unbiased bases are mutually unbiased bases. (fast track communication)

  15. Search Based Software Engineering

    OpenAIRE

    Jaspreet Bedi; Kuljit Kaur

    2014-01-01

    This paper reviews the search based software engineering research and finds the major milestones in this direction. The SBSE approach has been the topic of several surveys and reviews. Search Based Software Engineering (SBSE) consists of the application of search-based optimization to software engineering. Using SBSE, a software engineering task is formulated as a search problem by defining a suitable candidate solution representation and a fitness function to differentiate be...

  16. Case-based reasoning

    CERN Document Server

    Kolodner, Janet

    1993-01-01

    Case-based reasoning is one of the fastest growing areas in the field of knowledge-based systems and this book, authored by a leader in the field, is the first comprehensive text on the subject. Case-based reasoning systems are systems that store information about situations in their memory. As new problems arise, similar situations are searched out to help solve these problems. Problems are understood and inferences are made by finding the closest cases in memory, comparing and contrasting the problem with those cases, making inferences based on those comparisons, and asking questions whe

  17. XML-BASED REPRESENTATION

    Energy Technology Data Exchange (ETDEWEB)

    R. KELSEY

    2001-02-01

    For focused applications with limited user and use application communities, XML can be the right choice for representation. It is easy to use, maintain, and extend and enjoys wide support in commercial and research sectors. When the knowledge and information to be represented is object-based and use of that knowledge and information is a high priority, then XML-based representation should be considered. This paper discusses some of the issues involved in using XML-based representation and presents an example application that successfully uses an XML-based representation.

  18. Gasification-based biomass

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2009-01-18

    The gasification-based biomass section of the Renewable Energy Technology Characterizations describes the technical and economic status of this emerging renewable energy option for electricity supply.

  19. Monitoring Knowledge Base (MKB)

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Monitoring Knowledge Base (MKB) is a compilation of emissions measurement and monitoring techniques associated with air pollution control devices, industrial...

  20. Guarded Hybrid Knowledge Bases

    CERN Document Server

    Heymans, Stijn; Predoiu, Livia; Feier, Cristina; Van Nieuwenborgh, Davy

    2007-01-01

    Recently, there has been a lot of interest in the integration of Description Logics and rules on the Semantic Web.We define guarded hybrid knowledge bases (or g-hybrid knowledge bases) as knowledge bases that consist of a Description Logic knowledge base and a guarded logic program, similar to the DL+log knowledge bases from (Rosati 2006). G-hybrid knowledge bases enable an integration of Description Logics and Logic Programming where, unlike in other approaches, variables in the rules of a guarded program do not need to appear in positive non-DL atoms of the body, i.e. DL atoms can act as guards as well. Decidability of satisfiability checking of g-hybrid knowledge bases is shown for the particular DL DLRO, which is close to OWL DL, by a reduction to guarded programs under the open answer set semantics. Moreover, we show 2-EXPTIME-completeness for satisfiability checking of such g-hybrid knowledge bases. Finally, we discuss advantages and disadvantages of our approach compared with DL+log knowledge bases.

  1. BIOMETRICS BASED USER AUTHENTICATION

    OpenAIRE

    Tanuj Tiwari; Tanya Tiwari2; Sanjay Tiwari

    2015-01-01

    Biometrics is automated methods of recognizing a person based on a physiological or behavioral characteristic. Biometrics technologies are base for a plethora of highly secure identification and personal verification solutions. It is measurement of biological characteristics – either physiological or behavioral – that verify the claimed identity of an individual. Physiological biometrics include fingerprints, iris recognition. voice verification, retina recognition, palm vein patt...

  2. Model-based geostatistics

    CERN Document Server

    Diggle, Peter J

    2007-01-01

    Model-based geostatistics refers to the application of general statistical principles of modeling and inference to geostatistical problems. This volume provides a treatment of model-based geostatistics and emphasizes on statistical methods and applications. It also features analyses of datasets from a range of scientific contexts.

  3. Evidence based practice

    DEFF Research Database (Denmark)

    Hjørland, Birger

    2011-01-01

    Evidence-based practice (EBP) is an influential interdisciplinary movement that originated in medicine as evidence-based medicine (EBM) about 1992. EBP is of considerable interest to library and information science (LIS) because it focuses on a thorough documentation of the basis for the decision...

  4. Arkansas' Disappearing Tax Base.

    Science.gov (United States)

    Schoppmeyer, Martin; Venters, Tommy

    State legislation that has contributed to the reduction of Arkansas' tax base is described in this paper. Amendment 59, adopted in 1980, has reduced the state tax base by millions of dollars. At the end of 1992, the majority of school districts have equalized their real, personal, and carrier and utility property. Act 34, the current foundation…

  5. Diffusion Based Photon Mapping

    DEFF Research Database (Denmark)

    Schjøth, Lars; Fogh Olsen, Ole; Sporring, Jon

    2007-01-01

    . To address this problem we introduce a novel photon mapping algorithm based on nonlinear anisotropic diffusion. Our algorithm adapts according to the structure of the photon map such that smoothing occurs along edges and structures and not across. In this way we preserve the important illumination...... features, while eliminating noise. We call our method diffusion based photon mapping....

  6. Diffusion Based Photon Mapping

    DEFF Research Database (Denmark)

    Schjøth, Lars; Olsen, Ole Fogh; Sporring, Jon

    2006-01-01

    . To address this problem we introduce a novel photon mapping algorithm based on nonlinear anisotropic diffusion. Our algorithm adapts according to the structure of the photon map such that smoothing occurs along edges and structures and not across. In this way we preserve the important illumination...... features, while eliminating noise. We call our method diffusion based photon mapping....

  7. Zero-Based Budgeting.

    Science.gov (United States)

    Wichowski, Chester

    1979-01-01

    The zero-based budgeting approach is designed to achieve the greatest benefit with the fewest undesirable consequences. Seven basic steps make up the zero-based decision-making process: (1) identifying program goals, (2) classifying goals, (3) identifying resources, (4) reviewing consequences, (5) developing decision packages, (6) implementing a…

  8. Hydrogel based occlusion systems

    NARCIS (Netherlands)

    Stam, F.A.; Jackson, N.; Dubruel, P.; Adesanya, K.; Embrechts, A.; Mendes, E.; Neves, H.P.; Herijgers, P.; Verbrugghe, Y.; Shacham, Y.; Engel, L.; Krylov, V.

    2013-01-01

    A hydrogel based occlusion system, a method for occluding vessels, appendages or aneurysms, and a method for hydrogel synthesis are disclosed. The hydrogel based occlusion system includes a hydrogel having a shrunken and a swollen state and a delivery tool configured to deliver the hydrogel to a tar

  9. Game-Based Teaching

    DEFF Research Database (Denmark)

    Hanghøj, Thorkild

    2013-01-01

    This chapter outlines theoretical and empirical perspectives on how Game-Based Teaching can be integrated within the context of formal schooling. Initially, this is done by describing game scenarios as models for possible actions that need to be translated into curricular knowledge practices...... approaches to game-based teaching, which may or may not correspond with the pedagogical models of particular games....

  10. Secure base stations

    NARCIS (Netherlands)

    Bosch, Peter; Brusilovsky, Alec; McLellan, Rae; Mullender, Sape; Polakos, Paul

    2009-01-01

    With the introduction of the third generation (3G) Universal Mobile Telecommunications System (UMTS) base station router (BSR) and fourth generation (4G) base stations, such as the 3rd Generation Partnership Project (3GPP) Long Term Evolution (LTE) Evolved Node B (eNB), it has become important to se

  11. Bases de dades relacionals

    OpenAIRE

    Villegas González, Daniel

    2016-01-01

    Les empreses de reclutament de personal han d¿afrontar una sèrie de reptes per les seves tasques diàries, pel gran volum de candidats per cobrir les necessitats del mercat de llocs de treball. RecruitCAT és una empresa de reclutament de personal que necessita gestionar la seva base de dades. El objectiu és dissenyar i implementar una base de dades per gestionar una empresa de reclutament de personal, assolint les tasques d¿estudi, plantejament teòric i els scripts de generació de la base d...

  12. Profile Based Information Retrieval

    Directory of Open Access Journals (Sweden)

    Athar shaikh,

    2011-04-01

    Full Text Available This paper present Profile Based information retrieval system(PBIR. This system provide the user to register with it and based on the users registered areas of interest the system searches the related and efficient information form the world wide web using the technique of web text mining and arranges the unstructured data into structured format and present it to the user. This system also stores the previously searched data and based on users areas of interest and rating awarded to the interest by the user his profile will be updated at particular scheduled time.

  13. CLOUD COMPUTING BASED ORIENTATION

    OpenAIRE

    K. Jithendar; K.Srujan Raju; K. Neeraja

    2013-01-01

    With the rapid increase in the technology internet plays a major role in the society with the existence of the cloud based scenario. Where it is very much useful in the technology based on information related to the software oriented approach. It is mainly concerned about the utilities of the system which is the primary goal. It play a key role in the transmission of the data with a high definition oriented security based analysis respectively. Therefore whenever the user in the form of the c...

  14. Data base management study

    Science.gov (United States)

    1976-01-01

    Data base management techniques and applicable equipment are described. Recommendations which will assist potential NASA data users in selecting and using appropriate data base management tools and techniques are presented. Classes of currently available data processing equipment ranging from basic terminals to large minicomputer systems were surveyed as they apply to the needs of potential SEASAT data users. Cost and capabilities projections for this equipment through 1985 were presented. A test of a typical data base management system was described, as well as the results of this test and recommendations to assist potential users in determining when such a system is appropriate for their needs. The representative system tested was UNIVAC's DMS 1100.

  15. QuickBase

    CERN Document Server

    Conner, Nancy

    2007-01-01

    Ready to put Intuit's QuickBase to work? Our new Missing Manual shows you how to capture, modify, share, and manage data and documents with this web-based data-sharing program quickly and easily. No longer do you have to coordinate your team through a blizzard of emails or play frustrating games of "guess which document is the right one."QuickBase saves your organization time and money, letting you manage and share the information that makes your business tick: sales figures, project timelines, drafts of documents, purchase or work requests--whatever information you need to keep business flowi

  16. Lidar base specification

    Science.gov (United States)

    Heidemann, Hans Karl.

    2012-01-01

    In late 2009, a $14.3 million allocation from the “American Recovery and Reinvestment Act” for new light detection and ranging (lidar) elevation data prompted the U.S. Geological Survey (USGS) National Geospatial Program (NGP) to develop a common base specification for all lidar data acquired for The National Map. Released as a draft in 2010 and formally published in 2012, the USGS–NGP “Lidar Base Specification Version 1.0” (now Lidar Base Specification) was quickly embraced as the foundation for numerous state, county, and foreign country lidar specifications.

  17. Biometric-based Technologies

    OpenAIRE

    OECD

    2004-01-01

    This report is intended to provide an understanding of the benefits and limitations of biometric-based technologies. It also includes information on existing privacy and security methodologies for assessing biometrics.

  18. Cheboygan Vessel Base

    Data.gov (United States)

    Federal Laboratory Consortium — Cheboygan Vessel Base (CVB), located in Cheboygan, Michigan, is a field station of the USGS Great Lakes Science Center (GLSC). CVB was established by congressional...

  19. Problem Based Learning

    DEFF Research Database (Denmark)

    de Graaff, Erik; Guerra, Aida

    Problem-Based Learning (PBL) is an innovative method to organize the learning process in such a way that the students actively engage in finding answers by themselves. During the past 40 years PBL has evolved and diversified resulting in a multitude in variations in models and practices. However...... model and in general problem based and project based learning. We apply the principle of teach as you preach. The poster aims to outline the visitors’ workshop programme showing the results of some recent evaluations......., the key principles remain the same everywhere. Graaff & Kolmos (2003) identify the main PBL principles as follows: 1. Problem orientation 2. Project organization through teams or group work 3. Participant-directed 4. Experiental learning 5. Activity-based learning 6. Interdisciplinary learning and 7...

  20. Noncommutative Involutive Bases

    CERN Document Server

    Evans, G A

    2006-01-01

    The theory of Groebner Bases originated in the work of Buchberger and is now considered to be one of the most important and useful areas of symbolic computation. A great deal of effort has been put into improving Buchberger's algorithm for computing a Groebner Basis, and indeed in finding alternative methods of computing Groebner Bases. Two of these methods include the Groebner Walk method and the computation of Involutive Bases. By the mid 1980's, Buchberger's work had been generalised for noncommutative polynomial rings by Bergman and Mora. This thesis provides the corresponding generalisation for Involutive Bases and (to a lesser extent) the Groebner Walk, with the main results being as follows. (1) Algorithms for several new noncommutative involutive divisions are given, including strong; weak; global and local divisions. (2) An algorithm for computing a noncommutative Involutive Basis is given. When used with one of the aforementioned involutive divisions, it is shown that this algorithm returns a noncom...

  1. Mutually unbiased bases

    Indian Academy of Sciences (India)

    S Chaturvedi

    2002-08-01

    After a brief review of the notion of a full set of mutually unbiased bases in an -dimensional Hilbert space, we summarize the work of Wootters and Fields (W K Wootters and B C Fields, Ann. Phys. 191, 363 (1989)) which gives an explicit construction for such bases for the case = r, where is a prime. Further, we show how, by exploiting certain freedom in the Wootters–Fields construction, the task of explicitly writing down such bases can be simplified for the case when is an odd prime. In particular, we express the results entirely in terms of the character vectors of the cyclic group of order . We also analyse the connection between mutually unbiased bases and the representations of .

  2. Kelomehele preemia Baseli festivalil

    Index Scriptorium Estoniae

    2000-01-01

    Baselis festivalil "VIPER - International Festival for Film Video and New Media" tunnistati parimaks CD-ROMiks Gustav Deutschi/Anna Schimeki "Odysee today", netiprojektiks itaallaste "01.ORG", äramärkimispreemia - Raivo Kelomehe "Videoweaver"

  3. WormBase

    Data.gov (United States)

    U.S. Department of Health & Human Services — WormBase is an international consortium of biologists and computer scientists dedicated to providing the research community with accurate, current, accessible...

  4. Language-Based Learning Disabilities

    Science.gov (United States)

    ... Public / Speech, Language and Swallowing / Disorders and Diseases Language-Based Learning Disabilities (Reading, Spelling, and Writing) What ... a language-based learning disability ? What is a language-based learning disability? Language-based learning disabilities are ...

  5. Participatory design based research

    DEFF Research Database (Denmark)

    Dau, Susanne; Falk, Lars; Jensen, Louise Bach

    2014-01-01

    This poster reveal how participatory design based research by the use of a CoED inspired creative process can be used for designing solutions to problems regarding students study activities outside campus.......This poster reveal how participatory design based research by the use of a CoED inspired creative process can be used for designing solutions to problems regarding students study activities outside campus....

  6. DSP Based Waveform Generator

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The DSP Based Waveform Generator is used for CSR Control system to control special controlled objects, such as the pulsed power supply for magnets, RF system, injection and extraction synchronization, global CSR synchronization etc. This intelligent controller based on 4800 MIPS DSP and 256M SDRAM technology will supply highly stable and highly accurate reference waveform used by the power supply of magnets. The specifications are as follows:

  7. Optimisation-based clearance

    OpenAIRE

    Varga, Andras

    2002-01-01

    The basic feature of the optimisation-based clearance approach is to reformulate the clearance problems as equivalent minimum distance problems for which ”anti”-optimisation is performed to determine the worst-case parameter combination/ flight condition leading to worst performance. The basic requirements for the applicability of the optimisation-based approach are the availability of suitable parametric models describing the overall nonlinear dynamics of the augmented aircraft and of accomp...

  8. Computer-based simulations

    OpenAIRE

    Antonoaie, C.; Antonoaie, N.

    2010-01-01

    A computer-based simulation replicates an environment through a computer program designed to consider multiple variables, interactions, and system constraints. Computer-based simulation is used in organization studies to model human social systems to better understand the dynamics between individual and group behaviours.These methods advance organization studies research in many ways. They can be used for extrapolating theory, validating hypotheses, or revealing emergent behaviour. Simulation...

  9. Evidence-Based Development

    DEFF Research Database (Denmark)

    Hertzum, Morten; Simonsen, Jesper

    2004-01-01

    Systems development is replete with projects that represent substantial resource investments but result in systems that fail to meet users’ needs. Evidence-based development is an emerging idea intended to provide means for managing customer-vendor relationships and working systematically toward...... and electronic patient records for diabetes patients, this paper reports research in progress regarding the prospects and pitfalls of evidence-based development....

  10. Layered nickel based superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Ronning, Filip [Los Alamos National Laboratory; Bauer, Eric D [Los Alamos National Laboratory; Park, Tuson [Los Alamos National Laboratory; Kurita, Nobuyuki [Los Alamos National Laboratory; Klimczuk, T [Los Alamos National Laboratory; Movshovich, R [Los Alamos National Laboratory; Thompson, J D [Los Alamos National Laboratory; Sefat, A S [ORNL; Mandrus, D [ORNL

    2009-01-01

    We review the properties of Ni-based superconductors which contain Ni{sub 2}X{sub 2} (X=As, P, Bi, Si, Ge, B) planes, a common structural element to the recently discovered FeAs superconductors. We also compare the properties ofthe Ni-and Fe-based systems from a perspective ofelectronic structure as well as structure-property relations.

  11. Team Based Learning

    OpenAIRE

    ALTINTAŞ, Levent; ALİMOĞLU, Mustafa Kemal

    2012-01-01

    Team-based learning is a learner-centered instructional strategy led by an expert instructor and applied in large learner groups composed of teams including 5-7 individuals in each. The method requires some out-of-class and in-class activities and special team assignments for students to learn at individual and team level. In pure team-based learning, there are three phases: preparation, readiness assurance and application-oriented activities. Peer assessment is used to ensure desire...

  12. Compression-based similarity

    OpenAIRE

    Vitányi, Paul

    2011-01-01

    First we consider pair-wise distances for literal objects consisting of finite binary files. These files are taken to contain all of their meaning, like genomes or books. The distances are based on compression of the objects concerned, normalized, and can be viewed as similarity distances. Second, we consider pair-wise distances between names of objects, like "red" or "christianity." In this case the distances are based on searches of the Internet. Such a search can be performed by any search...

  13. Hydrogel based occlusion systems

    OpenAIRE

    Stam, F.A.; Jackson, N.; Dubruel, P.; Adesanya, K.; Embrechts, A.; Mendes, E.; Neves, H.P.; Herijgers, P.; Verbrugghe, Y.; Shacham, Y; Engel, L.; Krylov, V.

    2013-01-01

    A hydrogel based occlusion system, a method for occluding vessels, appendages or aneurysms, and a method for hydrogel synthesis are disclosed. The hydrogel based occlusion system includes a hydrogel having a shrunken and a swollen state and a delivery tool configured to deliver the hydrogel to a target occlusion location. The hydrogel is configured to permanently occlude the target occlusion location in the swollen state. The hydrogel may be an electro-activated hydrogel (EAH) which could be ...

  14. REST based mobile applications

    Science.gov (United States)

    Rambow, Mark; Preuss, Thomas; Berdux, Jörg; Conrad, Marc

    2008-02-01

    Simplicity is the major advantage of REST based webservices. Whereas SOAP is widespread in complex, security sensitive business-to-business aplications, REST is widely used for mashups and end-user centric applicatons. In that context we give an overview of REST and compare it to SOAP. Furthermore we apply the GeoDrawing application as an example for REST based mobile applications and emphasize on pros and cons for the use of REST in mobile application scenarios.

  15. LDEF materials data bases

    Science.gov (United States)

    Funk, Joan G.; Strickland, John W.; Davis, John M.

    1993-01-01

    The Long Duration Exposure Facility (LDEF) and the accompanying experiments were composed of and contained a wide variety of materials representing the largest collection of materials flown in low Earth orbit (LEO) and retrieved for ground based analysis to date. The results and implications of the mechanical, thermal, optical, and electrical data from these materials are the foundation on which future LEO space missions will be built. The LDEF Materials Special Investigation Group (MSIG) has been charged with establishing and developing data bases to document these materials and their performance to assure not only that the data are archived for future generations but also that the data are available to the spacecraft user community in an easily accessed, user-friendly form. This paper discusses the format and content of the three data bases developed or being developed to accomplish this task. The hardware and software requirements for each of these three data bases are discussed along with current availability of the data bases. This paper also serves as a user's guide to the MAPTIS LDEF Materials Data Base.

  16. Noncommutative Involutive Bases

    Science.gov (United States)

    Alun Evans, Gareth

    2006-02-01

    The theory of Groebner Bases originated in the work of Buchberger and is now considered to be one of the most important and useful areas of symbolic computation. A great deal of effort has been put into improving Buchberger's algorithm for computing a Groebner Basis, and indeed in finding alternative methods of computing Groebner Bases. Two of these methods include the Groebner Walk method and the computation of Involutive Bases. By the mid 1980's, Buchberger's work had been generalised for noncommutative polynomial rings by Bergman and Mora. This thesis provides the corresponding generalisation for Involutive Bases and (to a lesser extent) the Groebner Walk, with the main results being as follows. (1) Algorithms for several new noncommutative involutive divisions are given, including strong; weak; global and local divisions. (2) An algorithm for computing a noncommutative Involutive Basis is given. When used with one of the aforementioned involutive divisions, it is shown that this algorithm returns a noncommutative Groebner Basis on termination. (3) An algorithm for a noncommutative Groebner Walk is given, in the case of conversion between two harmonious monomial orderings. It is shown that this algorithm generalises to give an algorithm for performing a noncommutative Involutive Walk, again in the case of conversion between two harmonious monomial orderings. (4) Two new properties of commutative involutive divisions are introduced (stability and extendibility), respectively ensuring the termination of the Involutive Basis algorithm and the applicability (under certain conditions) of homogeneous methods of computing Involutive Bases.

  17. Underwater behaviour of bitumen coated radioactive wastes: experimental validation of the Colonbo degradation model; Comportement sous eau des dechets radioactifs bitumes: validation experimentale du modele de degradation Colonbo

    Energy Technology Data Exchange (ETDEWEB)

    Gwinner, B

    2004-03-01

    In the release scenario considered for geologic repository, water is thought to be the main aggressive agent with regards to bituminized radioactive waste (composed in general of 60 weight % of bitumen, 40% of soluble/insoluble salts and a few ppm of radionuclides). Since liquid water can diffuse in pure bitumen, leaching of bituminized waste results in the dissolution of the most soluble salts and leads to the development of a more or less concentrated saline solution-filled pore structure (called permeable layer). In consequence of the generation of a porous layer in the bituminized waste, leaching of salts and radionuclides can then take place. Research performed at the Atomic Energy Commission (CEA) aims therefore at understanding the consequences of ground-water immersion on the transport properties and radionuclides leaching of bituminized waste materials. To this end, a constitutive model (called COLONBO) which describes mathematically the leaching of bituminized waste has been developed. The COLONBO model is based on the following assumptions: 1. Water and dissolved salts migrate in the permeable layer according to Fick's first law. The diffusion of water and salts are quantified by effective diffusion coefficients which are unknown. 2. The mechanical properties of the bitumen matrix are not considered during leaching (free swelling). Up to now, the COLONBO model has been used only to model experimental water uptake and salt leach curves, leading (theoretical) estimates of the effective diffusion coefficients of water and salts in the permeable layer. The aim of this work was to validate experimentally the numerical results obtained with the COLONBO model. First, the correspondence between experimental and simulated water uptake and salt leach rates obtained on various bituminized waste materials is checked, leading estimates of the effective diffusion coefficients of water and salts in the permeable layer. Second, the evolution of the thickness and of

  18. Underwater behaviour of bitumen coated radioactive wastes: experimental validation of the Colonbo degradation model

    International Nuclear Information System (INIS)

    In the release scenario considered for geologic repository, water is thought to be the main aggressive agent with regards to bituminized radioactive waste (composed in general of 60 weight % of bitumen, 40% of soluble/insoluble salts and a few ppm of radionuclides). Since liquid water can diffuse in pure bitumen, leaching of bituminized waste results in the dissolution of the most soluble salts and leads to the development of a more or less concentrated saline solution-filled pore structure (called permeable layer). In consequence of the generation of a porous layer in the bituminized waste, leaching of salts and radionuclides can then take place. Research performed at the Atomic Energy Commission (CEA) aims therefore at understanding the consequences of ground-water immersion on the transport properties and radionuclides leaching of bituminized waste materials. To this end, a constitutive model (called COLONBO) which describes mathematically the leaching of bituminized waste has been developed. The COLONBO model is based on the following assumptions: 1. Water and dissolved salts migrate in the permeable layer according to Fick's first law. The diffusion of water and salts are quantified by effective diffusion coefficients which are unknown. 2. The mechanical properties of the bitumen matrix are not considered during leaching (free swelling). Up to now, the COLONBO model has been used only to model experimental water uptake and salt leach curves, leading (theoretical) estimates of the effective diffusion coefficients of water and salts in the permeable layer. The aim of this work was to validate experimentally the numerical results obtained with the COLONBO model. First, the correspondence between experimental and simulated water uptake and salt leach rates obtained on various bituminized waste materials is checked, leading estimates of the effective diffusion coefficients of water and salts in the permeable layer. Second, the evolution of the thickness and of the

  19. Nitramine Double Base Propellants

    Directory of Open Access Journals (Sweden)

    M. M. Bhalerao

    1996-10-01

    Full Text Available This review paper broadly covers the studies conducted on nitramine double base (DB propellants, particularly in the field of formulations, evaluation, catalysis and combustion mechanism . Addition of RDX and HMX in double base matrix shows relatively low burn rates and high paper index values. Further, the burn rate of this class of propellants enhances in the presence of energetic binders/plasticisers like glycidyl azide polymer. This paper also discusses the combustion mechanism of HMX/RDX-based DB propellants, especially in the presence of catalytic salts. As scanty data is available on extruded nitramine DB propellants, further work is needed in the field of formulation as well as evaluation with a view to generate exhaustive data.

  20. SAR based adaptive GMTI

    Science.gov (United States)

    Vu, Duc; Guo, Bin; Xu, Luzhou; Li, Jian

    2010-04-01

    We consider ground moving target indication (GMTI) and target velocity estimation based on multi-channel synthetic aperture radar (SAR) images. Via forming velocity versus cross-range images, we show that small moving targets can be detected even in the presence of strong stationary ground clutter. Moreover, the velocities of the moving targets can be estimated, and the misplaced moving targets can be placed back to their original locations based on the estimated velocities. Adaptive beamforming techniques, including Capon and generalizedlikelihood ratio test (GLRT), are used to form velocity versus cross-range images for each range bin of interest. The velocity estimation ambiguities caused by the multi-channel array geometry are analyzed. We also demonstrate the effectiveness of our approaches using the Air Force Research Laboratory (AFRL) publicly-released Gotcha SAR based GMTI data set.

  1. Cantilever Based Mass Sensing

    DEFF Research Database (Denmark)

    Dohn, Søren

    2007-01-01

    Cantilever based mass sensors utilize that a change in vibrating mass will cause a change in the resonant frequency. This can be used for very accurate sensing of adsorption and desorption processes on the cantilever surface. The change in resonant frequency caused by a single molecule depends...... on various parameters including the vibrating mass of the cantilever and the frequency at which it vibrates. The minimum amount of molecules detectable is highly dependent on the noise of the system as well as the method of readout. The aim of this Ph.D. thesis has been twofold: To develop a readout method...... suitable for a portable device and to investigate the possibility of enhancing the functionality and sensitivity of cantilever based mass sensors. A readout method based on the hard contact between the cantilever and a biased electrode placed in close proximity to the cantilever is proposed. The viability...

  2. Location-based Scheduling

    DEFF Research Database (Denmark)

    Andersson, Niclas; Christensen, Knud

    the predominant scheduling method since it was introduced in the late 1950s. Over the years, CPM has proven to be a very powerful technique for planning, scheduling and controlling projects, which among other things is indicated by the development of a large number of CPM-based software applications available...... on the market. However, CPM is primarily an activity based method that takes the activity as the unit of focus and there is criticism raised, specifically in the case of construction projects, on the method for deficient management of construction work and continuous flow of resources. To seek solutions...... to the identified limitations of the CPM method, an alternative planning and scheduling methodology that includes locations is tested. Location-based Scheduling (LBS) implies a shift in focus, from primarily the activities to the flow of work through the various locations of the project, i.e. the building. LBS uses...

  3. Inkjet-based micromanufacturing

    CERN Document Server

    Korvink, Jan G; Shin, Dong-Youn; Brand, Oliver; Fedder, Gary K; Hierold, Christofer; Tabata, Osamu

    2012-01-01

    Inkjet-based Micromanufacturing Inkjet technology goes way beyond putting ink on paper: it enables simpler, faster and more reliable manufacturing processes in the fields of micro- and nanotechnology. Modern inkjet heads are per se precision instruments that deposit droplets of fluids on a variety of surfaces in programmable, repeating patterns, allowing, after suitable modifications and adaptations, the manufacturing of devices such as thin-film transistors, polymer-based displays and photovoltaic elements. Moreover, inkjet technology facilitates the large-scale production of flexible RFID tr

  4. Identity-based encryption

    CERN Document Server

    Chatterjee, Sanjit

    2011-01-01

    Identity Based Encryption (IBE) is a type of public key encryption and has been intensely researched in the past decade. Identity-Based Encryption summarizes the available research for IBE and the main ideas that would enable users to pursue further work in this area. This book will also cover a brief background on Elliptic Curves and Pairings, security against chosen Cipher text Attacks, standards and more. Advanced-level students in computer science and mathematics who specialize in cryptology, and the general community of researchers in the area of cryptology and data security will find Ide

  5. Video-based rendering

    CERN Document Server

    Magnor, Marcus A

    2005-01-01

    Driven by consumer-market applications that enjoy steadily increasing economic importance, graphics hardware and rendering algorithms are a central focus of computer graphics research. Video-based rendering is an approach that aims to overcome the current bottleneck in the time-consuming modeling process and has applications in areas such as computer games, special effects, and interactive TV. This book offers an in-depth introduction to video-based rendering, a rapidly developing new interdisciplinary topic employing techniques from computer graphics, computer vision, and telecommunication en

  6. Domain based metering

    OpenAIRE

    Párhonyi, Robert; Beijnum, van, Bert-Jan

    2000-01-01

    In the last two years, there is a gaining interest in usage based accounting for the Internet. One of the driving forces for this growing interest is the progress being made in providing some form of quality assurance in IP packet forwarding. One of the key processes in an accounting system is metering, gathering of network usage parameters on which the accounting is or can be based. In this paper are addressed issues that are potentially of interest in Internet accounting. One of these issue...

  7. Iron-based superconductivity

    CERN Document Server

    Johnson, Peter D; Yin, Wei-Guo

    2015-01-01

    This volume presents an in-depth review of experimental and theoretical studies on the newly discovered Fe-based superconductors.  Following the Introduction, which places iron-based superconductors in the context of other unconventional superconductors, the book is divided into three sections covering sample growth, experimental characterization, and theoretical understanding.  To understand the complex structure-property relationships of these materials, results from a wide range of experimental techniques and theoretical approaches are described that probe the electronic and magnetic prope

  8. Plasmonics based VLSI processes

    Directory of Open Access Journals (Sweden)

    Shreya Bhattacharya

    2013-03-01

    Full Text Available In continuum to my previous paper titled ‘Implementation of plasmonics in VLSI’, this paper attempts to explore further, the actual physical realization of an all-plasmonic chip. In this paper, various methods of plasmon-based photolithography have been discussed and an observation is made w.r.t the cost effectiveness and ease of adaptability. Also, plasmonics based active element has been discussed which would help unravel further arenas of approaches and methods towards the realization of an all-plasmonic chip.

  9. Pitch Based Sound Classification

    DEFF Research Database (Denmark)

    Nielsen, Andreas Brinch; Hansen, Lars Kai; Kjems, U

    2006-01-01

    A sound classification model is presented that can classify signals into music, noise and speech. The model extracts the pitch of the signal using the harmonic product spectrum. Based on the pitch estimate and a pitch error measure, features are created and used in a probabilistic model with soft...

  10. Skull Base Tumors

    Science.gov (United States)

    Schulz-Ertner, Daniela

    In skull base tumors associated with a low radiosensitivity for conventional radiotherapy (RT), irradiation with proton or carbon ion beams facilitates a safe and accurate application of high tumor doses due to the favorable beam localization properties of these particle beams. Cranial nerves, the brain stem and normal brain tissue can at the same time be optimally spared.

  11. Base tree property

    Czech Academy of Sciences Publication Activity Database

    Balcar, B.; Doucha, Michal; Hrušák, M.

    2015-01-01

    Roč. 32, č. 1 (2015), s. 69-81. ISSN 0167-8094 R&D Projects: GA AV ČR IAA100190902 Institutional support: RVO:67985840 Keywords : forcing * Boolean algebra s * base tree Subject RIV: BA - General Mathematics Impact factor: 0.621, year: 2014 http://link.springer.com/article/10.1007/s11083-013-9316-2

  12. Surfel Based Geometry Resonstruction

    DEFF Research Database (Denmark)

    Andersen, Vedrana; Aanæs, Henrik; Bærentzen, Jakob Andreas

    We propose a method for retrieving a piecewise smooth surface from noisy data. In data acquired by a scanning process sampled points are almost never on the discontinuities making reconstruction of surfaces with sharp features difficult. Our method is based on a Markov Random Field (MRF) formulat...

  13. 80537 based distance relay

    DEFF Research Database (Denmark)

    Pedersen, Knud Ole Helgesen

    1999-01-01

    A method for implementing a digital distance relay in the power system is described.Instructions are given on how to program this relay on a 80537 based microcomputer system.The problem is used as a practical case study in the course 53113: Micocomputer applications in the power system.The relay is...

  14. Protein Crystal Based Nanomaterials

    Science.gov (United States)

    Bell, Jeffrey A.; VanRoey, Patrick

    2001-01-01

    This is the final report on a NASA Grant. It concerns a description of work done, which includes: (1) Protein crystals cross-linked to form fibers; (2) Engineering of protein to favor crystallization; (3) Better knowledge-based potentials for protein-protein contacts; (4) Simulation of protein crystallization.

  15. Internet based benchmarking

    DEFF Research Database (Denmark)

    Bogetoft, Peter; Nielsen, Kurt

    2005-01-01

    We discuss the design of interactive, internet based benchmarking using parametric (statistical) as well as nonparametric (DEA) models. The user receives benchmarks and improvement potentials. The user is also given the possibility to search different efficiency frontiers and hereby to explore...

  16. Zero Base Budgeting.

    Science.gov (United States)

    Sarndal, Anne G.

    1979-01-01

    Traditional budgeting starts with the previous year's budget, but zero base budgeting demands that each activity be justified from "scratch," and establishes a number of increments for each unit, in order of priority. Given the set of increments and the money available, management can determine what activities to finance. (Author)

  17. Diffusion Based Photon Mapping

    DEFF Research Database (Denmark)

    Schjøth, Lars; Sporring, Jon; Fogh Olsen, Ole

    2008-01-01

    . To address this problem, we introduce a photon mapping algorithm based on nonlinear anisotropic diffusion. Our algorithm adapts according to the structure of the photon map such that smoothing occurs along edges and structures and not across. In this way, we preserve important illumination features...

  18. BASE - Progress Report 2015

    CERN Document Server

    Ulmer, S; Mooser, A; Sellner, S; Nagahama, H; Higuchi, T; Borchert, M; Schneider, G; Tanaka, T; Blaum, K; Matsuda, Y; Ospelkaus, C; Quint, W; Walz, J; Yamazaki, Y; CERN. Geneva. SPS and PS Experiments Committee; SPSC

    2016-01-01

    The BASE collaboration aims at high-precision comparisons of the fundamental properties of the proton and the antiproton, namely, the magnetic g-factors as well as the charge-to-mass ratios of the particles. This annual report summarizes the achievements made in CERN's 2015 antiproton run.

  19. Animation-based Sketching

    DEFF Research Database (Denmark)

    Vistisen, Peter

    experiments has been carried out, applying animation-based sketching in various contexts and at varying points in the design process. In the studies, I evaluate the viability of the approach, the practical integration into the design process, and map how consensus between stakeholders in design can be...

  20. XML Based UIScript

    Institute of Scientific and Technical Information of China (English)

    CAI Bin; LIAO Jian-xin; SHEN Qi-wei

    2004-01-01

    In this paper, after the analyzing the UIScript mechanism in intelligent peripheral, a new approach of XML-based UIScript is put forward. The related issues such as the design of UIScript language, the execution environment and its relationship with other script languages are discussed.

  1. Evidence-based policy

    DEFF Research Database (Denmark)

    Vohnsen, Nina Holm

    2013-01-01

    research community (e.g. Boden & Epstein 2006; House of Commons 2006; Cartwright et al 2009; Rod 2010; Vohnsen 2011). This article intends to draw out some general pitfalls in the curious meeting of science and politics by focusing on a particular attempt to make evidence-based legislation in Denmark (for...

  2. Centroid Based Text Clustering

    Directory of Open Access Journals (Sweden)

    Priti Maheshwari

    2010-09-01

    Full Text Available Web mining is a burgeoning new field that attempts to glean meaningful information from natural language text. Web mining refers generally to the process of extracting interesting information and knowledge from unstructured text. Text clustering is one of the important Web mining functionalities. Text clustering is the task in which texts are classified into groups of similar objects based on their contents. Current research in the area of Web mining is tacklesproblems of text data representation, classification, clustering, information extraction or the search for and modeling of hidden patterns. In this paper we propose for mining large document collections it is necessary to pre-process the web documents and store the information in a data structure, which is more appropriate for further processing than a plain web file. In this paper we developed a php-mySql based utility to convert unstructured web documents into structured tabular representation by preprocessing, indexing .We apply centroid based web clustering method on preprocessed data. We apply three methods for clustering. Finally we proposed a method that can increase accuracy based on clustering ofdocuments.

  3. Inservice testing bases program

    International Nuclear Information System (INIS)

    Inservice testing (IST) programs generally address those components necessary for safe operation as specified in Subsections IWP-1100 and IWV-1100 of Section 11 (American Society of Mechanical Engineers Boiler and Pressure Vessel Code) and Position 11 of the US Nuclear Regulatory Commission Generic Letter 89-04. Program tables, generated manually or from computer databases, are frequently used to describe those components and testing requirements contained in IST programs. Table entries are usually derived from review of system drawings, accident analysis, and other technical documents; however, the bases for such entries are not always documented. Because IST programs are dynamic, the continual evaluation of program entries may be inhibited if bases for program entries are unclear. When IST programs have been developed by architect-engineers, nuclear steam supply system suppliers, or other contractors, the bases for IST program contents become even more nebulous to the program users. The presentation provides a discussion of IST bases programs used by Entergy Operations' four nuclear plants, and the benefits derived from their use

  4. Dictionary Based Image Segmentation

    DEFF Research Database (Denmark)

    Dahl, Anders Bjorholm; Dahl, Vedrana Andersen

    2015-01-01

    We propose a method for weakly supervised segmentation of natural images, which may contain both textured or non-textured regions. Our texture representation is based on a dictionary of image patches. To divide an image into separated regions with similar texture we use an implicit level sets...

  5. Problem-Based Learning

    Science.gov (United States)

    Allen, Deborah E.; Donham, Richard S.; Bernhardt, Stephen A.

    2011-01-01

    In problem-based learning (PBL), students working in collaborative groups learn by resolving complex, realistic problems under the guidance of faculty. There is some evidence of PBL effectiveness in medical school settings where it began, and there are numerous accounts of PBL implementation in various undergraduate contexts, replete with…

  6. Performance based fault diagnosis

    DEFF Research Database (Denmark)

    Niemann, Hans Henrik

    2002-01-01

    Different aspects of fault detection and fault isolation in closed-loop systems are considered. It is shown that using the standard setup known from feedback control, it is possible to formulate fault diagnosis problems based on a performance index in this general standard setup. It is also shown...

  7. Aptamer-based nanobiosensors.

    Science.gov (United States)

    Kim, Yeon Seok; Raston, Nurul Hanun Ahmad; Gu, Man Bock

    2016-02-15

    It has been more than two decades since aptamer and the systematic evolution of ligands by exponential enrichment (SELEX) method were discovered by Larry Gold and Andrew Ellington in 1990, respectively. Based on the various advantages of aptamers, they have become a potent rival of antibodies in therapeutics and bio-analysis. Especially, the recent advances in aptamer biosensor application are remarkable due to its intrinsic properties of aptamers as nucleic acids and target induced conformational changes, in addition to the introduction of graphene oxide-based easy and simple immobilization-free screening method even for dual aptamers. In addition, the incorporation of various nanomaterials such as metallic nanoparticles, carbon materials, and functional nanospheres in aptasensors has facilitated the improvement of analytical performance and commercial application of aptasensors. In this review, recent prominent reports on aptasensors utilizing nanomaterials were introduced to understand the principle of aptamer-based biosensors and provide an insight for new strategies of aptasensors and the application of various nanomaterials. The perspective on aptamer-based biosensors and diagnostics was also discussed in view of technology and market. PMID:26139320

  8. Lunar Base Sitting

    Science.gov (United States)

    Staehle, Robert L.; Burke, James D.; Snyder, Gerald C.; Dowling, Richard; Spudis, Paul D.

    1993-12-01

    Speculation with regard to a permanent lunar base has been with us since Robert Goddard was working on the first liquid-fueled rockets in the 1920's. With the infusion of data from the Apollo Moon flights, a once speculative area of space exploration has become an exciting possibility. A Moon base is not only a very real possibility, but is probably a critical element in the continuation of our piloted space program. This article, originally drafted by World Space Foundation volunteers in conjuction with various academic and research groups, examines some of the strategies involved in selecting an appropriate site for such a lunar base. Site selection involves a number of complex variables, including raw materials for possible rocket propellant generation, hot an cold cycles, view of the sky (for astronomical considerations, among others), geological makeup of the region, and more. This article summarizes the key base siting considerations and suggests some alternatives. Availability of specific resources, including energy and certain minerals, is critical to success.

  9. PROJECT-BASES RISK MANAGEMENT

    OpenAIRE

    Andrei Sandu

    2010-01-01

    The project-bases concept is presented. There are defined operations on project-bases. The software developed for project-bases management is analyzed based in its structure and functionality. A series of criteria of structuring risks is listed are tailored for project-bases management. Next there are suggested solutions of mitigating risks by maintaining efficiency within acceptable thresholds.

  10. Oil generation potential assessment and paleoenvironmental interpretation based on bio markers and stable carbon isotopes of the Pliensbachian - lower Toarcian (Lower Jurassic) of the Peniche region (Lusitanian Basin, Portugal); Avaliacao do potencial gerador de petroleo e interpretacao paleoambiental com base em biomarcadores e isotopos estaveis de carbono da secao Pliensbaquiano - Toarciano inferior (Jurassico Inferior) da regiao de Peniche (Bacia Lusitanica, Portugal)

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Luiz Carlos Veiga de; Rodrigues, Rene; Duarte, Luis Vitor; Lemos, Valesca Brasil [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES). Gerencia de Bioestratigrafia e Paleoecologia]. E-mail: lcveiga@petrobras.com.br

    2006-05-15

    The Lusitanian Basin (Portugal) is located on the western margin of the Iberian Plate with maximum sedimentary thickness around 5 km. In spite of containing promising petroleum systems and more than a hundred wells, its hydrocarbon generation potential has not been fully evaluated yet. These sediments range from upper Triassic to upper Cretaceous, mainly from the Jurassic age. The Lower Jurassic is particularly well represented in the Lusitanian Basin, specifically in the Peniche region, where there are more than 450 m thick outcrops of carbonate rocks aged between Sinemurian and Toarcian. This study presents the evaluation of the hydrocarbon generation potential of the Pliensbachian . lower Toarcian of the Peniche section; which includes the Vale das Fontes Formation, Lemede Formation and Cabo Carvoeiro Formation (CC1 and CC2 members) based on 233 rock samples analyzed for total organic carbon (TOC), Rock-Eval pyrolysis and bio markers. Available data of oxygen and carbon stable isotopes were also used in the paleoenvironmental interpretation. Marls and limestones with the bituminous facies (Mlbf) of the Vale das Fontes Formation, present the highest TOC values, up to 14.95%, corresponding to the ibex (upper part), davoei and margaritatus ammonites zones and part of the NJ4a and NJ4b nanno fossils bio zones (Pliensbachian). In thermal immature sections (T max about 430 deg C), this member also shows high S{sub 2} values (10 to 50 mgHC/g rock) and Hydrogen index (HI: 200 to 555 mgHC/g TOC). The correlation between HI x OI shows that type II kerogen is predominant in the portion of the section where TOC values are higher. The good positive correlation between TOC values and the bio markers ratio P/nC17 and sterane (C{sub 27}/C{sub 29}) throughout the Mlbf Member suggests a gradual increase of anoxia and higher contribution of algae in relation to terrestrial organic matter. Usually {delta}{sup 18}O variations observed in the basins of the Iberian Peninsula have been

  11. Quasigroup based crypto-algorithms

    OpenAIRE

    Shcherbacov, Victor

    2012-01-01

    Modifications of Markovski quasigroup based crypto-algorithm have been proposed. Some of these modifications are based on the systems of orthogonal n-ary groupoids. T-quasigroups based stream ciphers have been constructed.

  12. Spintronics-based computing

    CERN Document Server

    Prenat, Guillaume

    2015-01-01

    This book provides a comprehensive introduction to spintronics-based computing for the next generation of ultra-low power/highly reliable logic, which is widely considered a promising candidate to replace conventional, pure CMOS-based logic. It will cover aspects from device to system-level, including magnetic memory cells, device modeling, hybrid circuit structure, design methodology, CAD tools, and technological integration methods. This book is accessible to a variety of readers and little or no background in magnetism and spin electronics are required to understand its content.  The multidisciplinary team of expert authors from circuits, devices, computer architecture, CAD and system design reveal to readers the potential of spintronics nanodevices to reduce power consumption, improve reliability and enable new functionality.  .

  13. Graphene-based electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Xiao; Zeng, Zhiyuan; Fan, Zhanxi; Liu, Juqing; Zhang, Hua [School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore, 639798 (Singapore)

    2012-11-27

    Graphene, the thinnest two dimensional carbon material, has become the subject of intensive investigation in various research fields because of its remarkable electronic, mechanical, optical and thermal properties. Graphene-based electrodes, fabricated from mechanically cleaved graphene, chemical vapor deposition (CVD) grown graphene, or massively produced graphene derivatives from bulk graphite, have been applied in a broad range of applications, such as in light emitting diodes, touch screens, field-effect transistors, solar cells, supercapacitors, batteries, and sensors. In this Review, after a short introduction to the properties and synthetic methods of graphene and its derivatives, we will discuss the importance of graphene-based electrodes, their fabrication techniques, and application areas. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Graphene-based electrodes.

    Science.gov (United States)

    Huang, Xiao; Zeng, Zhiyuan; Fan, Zhanxi; Liu, Juqing; Zhang, Hua

    2012-11-27

    Graphene, the thinnest two dimensional carbon material, has become the subject of intensive investigation in various research fields because of its remarkable electronic, mechanical, optical and thermal properties. Graphene-based electrodes, fabricated from mechanically cleaved graphene, chemical vapor deposition (CVD) grown graphene, or massively produced graphene derivatives from bulk graphite, have been applied in a broad range of applications, such as in light emitting diodes, touch screens, field-effect transistors, solar cells, supercapacitors, batteries, and sensors. In this Review, after a short introduction to the properties and synthetic methods of graphene and its derivatives, we will discuss the importance of graphene-based electrodes, their fabrication techniques, and application areas. PMID:22927209

  15. Sparse approximation with bases

    CERN Document Server

    2015-01-01

    This book systematically presents recent fundamental results on greedy approximation with respect to bases. Motivated by numerous applications, the last decade has seen great successes in studying nonlinear sparse approximation. Recent findings have established that greedy-type algorithms are suitable methods of nonlinear approximation in both sparse approximation with respect to bases and sparse approximation with respect to redundant systems. These insights, combined with some previous fundamental results, form the basis for constructing the theory of greedy approximation. Taking into account the theoretical and practical demand for this kind of theory, the book systematically elaborates a theoretical framework for greedy approximation and its applications.  The book addresses the needs of researchers working in numerical mathematics, harmonic analysis, and functional analysis. It quickly takes the reader from classical results to the latest frontier, but is written at the level of a graduate course and do...

  16. Knowledge based maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Sturm, A. [Hamburgische Electacitaets-Werke AG Hamburg (Germany)

    1997-12-31

    The establishment of maintenance strategies is of crucial significance for the reliability of a plant and the economic efficiency of maintenance measures. Knowledge about the condition of components and plants from the technical and business management point of view therefore becomes one of the fundamental questions and the key to efficient management and maintenance. A new way to determine the maintenance strategy can be called: Knowledge Based Maintenance. A simple method for determining strategies while taking the technical condition of the components of the production process into account to the greatest possible degree which can be shown. A software with an algorithm for Knowledge Based Maintenance leads the user during complex work to the determination of maintenance strategies for this complex plant components. (orig.)

  17. Content Based Video Retrieval

    Directory of Open Access Journals (Sweden)

    B.V.Patel

    2012-11-01

    Full Text Available Content based video retrieval is an approach for facilitating the searching and browsing of large image collections over World Wide Web. In this approach, video analysis is conducted on low level visual properties extracted from video frame. We believed that in order to create an effective video retrieval system, visual perception must be taken into account. We conjectured that a technique which employs multiple features for indexing and retrieval would be more effective in the discrimination and search tasks of videos. In order to validate this claim, content based indexing and retrieval systems were implemented using color histogram, various texture features and other approaches. Videos were stored in Oracle 9i Database and a user study measured correctness of response.

  18. Content Based Video Retrieval

    Directory of Open Access Journals (Sweden)

    B. V. Patel

    2012-10-01

    Full Text Available Content based video retrieval is an approach for facilitating the searching and browsing of large image collections over World Wide Web. In this approach, video analysis is conducted on low level visual properties extracted from video frame. We believed that in order to create an effective video retrieval system, visual perception must be taken into account. We conjectured that a technique which employs multiple features for indexing and retrieval would be more effective in the discrimination and search tasks of videos. In order to validate this claim, content based indexing and retrieval systems were implemented using color histogram, various texture features and other approaches. Videos were stored in Oracle 9i Database and a user study measured correctness of response.

  19. Trajectory Based Traffic Analysis

    DEFF Research Database (Denmark)

    Krogh, Benjamin Bjerre; Andersen, Ove; Lewis-Kelham, Edwin;

    2013-01-01

    We present the INTRA system for interactive path-based traffic analysis. The analyses are developed in collaboration with traffic researchers and provide novel insights into conditions such as congestion, travel-time, choice of route, and traffic-flow. INTRA supports interactive point-and-click a......We present the INTRA system for interactive path-based traffic analysis. The analyses are developed in collaboration with traffic researchers and provide novel insights into conditions such as congestion, travel-time, choice of route, and traffic-flow. INTRA supports interactive point......-and-click analysis, due to a novel and efficient indexing structure. With the web-site daisy.aau.dk/its/spqdemo/we will demonstrate several analyses, using a very large real-world data set consisting of 1.9 billion GPS records (1.5 million trajectories) recorded from more than 13000 vehicles, and touching most of...

  20. Maintaining Relationship Based Procurement

    Directory of Open Access Journals (Sweden)

    Peter Davis

    2012-11-01

    Full Text Available Alliance and relationship projects are increasingin number and represent a large pool of work. Tobe successful relationship style contracts dependon soft-dollar factors, particularly the participants'ability to work together within an agreedframework, generally they are not based on lowbid tendering. Participants should be prepared todo business in an open environment based ontrust and mutually agreed governance. Theresearch evaluates relationship maintenance inthe implementation phase of constructionalliances - a particular derivative of relationshipstyle contracts. To determine the factors thatcontribute to relationship maintenance forty-nineexperienced Australian alliance projectmanagers were interviewed. The main findingswere; the development of relationships early inthe project form building blocks of success fromwhich relationships are maintained and projectvalue added; quality facilitation plays animportant part in relationship maintenance and ahybrid organisation created as a result of alliancedevelopment overcomes destructiveorganisational boundaries. Relationshipmaintenance is integral to alliance project controland failure to formalise it and pay attention toprocess and past outcomes will undermine analliance project's potential for success.

  1. Radiation-based security

    International Nuclear Information System (INIS)

    The problems presented in different security areas are varied but the solutions that have been offered are generally based upon the same principles. Employing radiation to locate and identify explosives or contraband has been most obvious at airports but other locations are now receiving equal attention. Neutron and X-ray interrogation are the systems most frequently employed. However, the more recently developed approaches such as multi-view dual-energy imaging and the use of high-speed diffraction measurements are the most likely systems to become widely available. This review looks briefly at the neutron and X-ray based systems that have been developed indicating their mode of operation and their advantages and disadvantages. It then summarizes the current state-of-the-art. The paper finishes by looking in some detail at one of the most promising areas of development--in-line diffraction measurements. (author)

  2. Skull base bone hyperpneumatization

    OpenAIRE

    Houet, E J; Kouokam, L.M.; Nchimi, A L

    2013-01-01

    A 50-year-old male with a long standing history of compulsive Valsalva maneuvers, complaining of episodes of vertigo underwent head computed tomography. Axial CT slices at the level of the skull base (Fig. A) and the first cervical vertebrae (Fig. B) shows an extensive unusual pneumatization of both the body and lateral processes of the first cervical vertebrae (arrows), with air pouches dissecting planes between bone cortex and the periosteum around the occipital bone and the lateral process...

  3. Spiritual-based Leadership

    DEFF Research Database (Denmark)

    Pruzan, Peter

    2015-01-01

    Although far from mainstream, the concept of spiritual-based leadership is emerging as an inclusive and yet highly personal approach to leadership that integrates a leader’s inner perspectives on identity, purpose, responsibility and success with her or his decisions and actions in the outer world...... of business—and therefore it is also emerging as a significant framework for understanding, practicing, communicating and teaching the art and profession of leadership....

  4. Refrigerator Based on Chemisorption

    Science.gov (United States)

    Jones, Jack A.

    1987-01-01

    Reversible chemical reaction generates pressurized oxygen for cooling. Concept for cryogenic refrigerator based on chemical absorption of oxygen by praseodymium/cerium oxide (PCO) compound. Refrigerator produces cryogenic liquid for cooling infrared sensors. Also used for liquefying air and separating oxygen from nitrogen in air. In chemisorption refrigerator, PCO alternately absorbs and desorbs oxygen depending on whether cooled or heated. One pair of compressors accepts oxygen while others releases it. Compressed oxygen liquefied when precooked and expanded.

  5. Model-based segmentation

    OpenAIRE

    Heimann, Tobias; Delingette, Hervé

    2011-01-01

    This chapter starts with a brief introduction into model-based segmentation, explaining the basic concepts and different approaches. Subsequently, two segmentation approaches are presented in more detail: First, the method of deformable simplex meshes is described, explaining the special properties of the simplex mesh and the formulation of the internal forces. Common choices for image forces are presented, and how to evolve the mesh to adapt to certain structures. Second, the method of point...

  6. Onlincolnshire Knowledge Base Collaboration

    OpenAIRE

    Fuller, Ted; Bosworth, Gary; Deville, Jane

    2016-01-01

    This report outlines the Onlincolnshire Knowledge Base Collaboration project undertaken by Lincoln Business School between May 2014 and September 2015. Onlincolnshire is a Lincolnshire County Council-run project which is part-funded by the East Midlands European Regional Development Fund (ERDF) Programme 2007 to 2013. As well as improving the broadband infrastructure, Onlincolnshire delivered a range of support to Lincolnshire’s Small and Medium Sized Enterprises (SMEs) through the “Business...

  7. Ferrocene base metal chelates

    International Nuclear Information System (INIS)

    Review of the works, devoted to different types of ferrocene metal chelates and to a possibility of ferrocene-containing ligand modification by means of complexing, is presented. Structure, properties and spectral characteristics of transitional metal, rare earth element, Cd2+, UO22+, Th4+ etc. complexes with ferrocene diketones, ferrocene acyl derivatives based on thiosemicarbazones and hydrazones and other heterometal ferrocene-containing metal chelates, are considered. 134 refs., 1 tab

  8. Polysiloxane based neutron detectors

    OpenAIRE

    Dalla Palma, Matteo

    2016-01-01

    In the last decade, neutron detection has been attracting the attention of the scientific community for different reasons. On one side, the increase in the price of 3He, employed in the most efficient and the most widely used neutron detectors. On the other side, the harmfulness of traditional xylene based liquid scintillators, used in extremely large volumes for the detection of fast neutrons. Finally, the demand for most compact and rough systems pushed by the increased popularity of neutro...

  9. Argument based machine learning

    OpenAIRE

    Možina, Martin

    2014-01-01

    The Thesis presents a novel approach to machine learning, called ABML (argument based machine learning). This approach combines machine learning from examples with some concepts from the field of defeasible argumentation, where arguments are used together with learning examples by learning methods in the induction of a hypothesis. An argument represents a relation between the class value of a particular learning example and its attributes and can be regarded as a partial explanation of this e...

  10. OCR Based Pixel Fusion

    OpenAIRE

    Rami Al-Hmouz

    2012-01-01

    Character recognition is the process that allows the automatic identification of character images, which is generally referred as Optical Character Recognition (OCR). The characters are either handwritten or typed. This study proposed a novel OCR approach based on the likelihood functions of pixels, which were obtained by averaging a trained set of character images. A Bayesian fusion process for all pixel probabilities decides the recognition of characters. Further tests using Support V...

  11. Lignocellulose-based bioproducts

    CERN Document Server

    Karimi, Keikhosro

    2015-01-01

    This volume provides the technical information required for the production of biofuels and chemicals from lignocellulosic biomass. It starts with a brief overview of the importance, applications, and production processes of different lignocellulosic products. Further chapters review the perspectives of waste-based biofuels and biochemicals; the pretreatment of lignocellulosic biomass for biofuel production; cellulolytic enzyme systems for the hydrolysis of lignocelluloses; and basic and applied aspects of the production of bioethanol, biogas, biohydrogen, and biobutanol from lignocelluloses.

  12. REST based service composition

    DEFF Research Database (Denmark)

    Grönvall, Erik; Ingstrup, Mads; Pløger, Morten;

    2011-01-01

    This paper presents an ongoing work developing and testing a Service Composition framework based upon the REST architecture named SECREST. A minimalistic approach have been favored instead of a creating a complete infrastructure. One focus has been on the system's interaction model. Indeed, an aim...... is to allow users in different healthcare scenarios to experiment with service composition to support highly individual and changing needs....

  13. Evidence based pediatrics.

    OpenAIRE

    Elizabeta ZISOVSKA

    2015-01-01

    It is very difficult to define the entire phrase “Evidence based pediatrics”, covering all components of this overused sentence. The definition comes out of the common sentence and it means integration of the individual clinical expertize together with the best external clinically available evidence of the systematic reviews which are of interest and benefit of the individual patient.Development of clinically appropriate structured question follows PICO model, i.e. containing f...

  14. Design bases - Concrete structures

    International Nuclear Information System (INIS)

    The most suitable title for Section 2 is 'Design Bases', which covers not only calculation but also the following areas: - Structural design concepts. - Project criteria. - Material specifications. These concepts are developed in more detail in the following sections. The numbering in this document is neither complete nor hierarchical since, for easier cross referencing, it corresponds to the paragraphs of Eurocode 2 Part 1 (hereinafter 'EUR-2') which are commented on. (author)

  15. MEMS based reference oscillator

    OpenAIRE

    Hedestig, Joel

    2005-01-01

    The interest in tiny wireless applications raises the demand for an integrated reference oscillator with the same performance as the macroscopic quartz crystal reference oscillators. The main challenge of the thesis is to prove that it is possible to build a MEMS based oscillator that approaches the accuracy level of existing quartz crystal oscillators. The MEMS resonator samples which Philips provides are measured and an equivalent electrical model is designed for them. This model is used in...

  16. Dictionary Based Image Segmentation

    OpenAIRE

    Dahl, Anders Bjorholm; Dahl, Vedrana Andersen

    2015-01-01

    We propose a method for weakly supervised segmentationof natural images, which may contain both textured or non-texturedregions. Our texture representation is based on a dictionary of imagepatches. To divide an image into separated regions with similar texturewe use an implicit level sets representation of the curve, which makesour method topologically adaptive. In addition, we suggest a multi-labelversion of the method. Finally, we improve upon a similar texture representation,by formulating...

  17. Knowledge Based Economy Assessment

    OpenAIRE

    Madalina Cristina Tocan

    2012-01-01

    The importance of knowledge-based economy (KBE) in the XXI century is evident. In the article the reflection of knowledge on economy is analyzed. The main point is targeted to the analysis of characteristics of knowledge expression in economy and to the construction of structure of KBE expression. This allows understanding the mechanism of functioning of knowledge economy. The authors highlight the possibility to assess the penetration level of KBE which could manifest itself trough the exist...

  18. Instance based function learning

    OpenAIRE

    Ramon, Jan; De Raedt, Luc

    1999-01-01

    The principles of instance based function learning are presented. In IBFL one is given a set of positive examples of a functional predicate. These examples are true ground facts that illustrate the input output behaviour of the predicate. The purpose is then to predict the output of the predicate given a new input. Further assumptions are that there is no background theory and that the inputs and outputs of the predicate consist of structured terms. IBFL is a novel technique that addresses th...

  19. Plasmonics based VLSI processes

    Directory of Open Access Journals (Sweden)

    Shreya Bhattacharya

    2013-04-01

    Full Text Available In continuum to my previous paper titled‘Implementation of plasmonics in VLSI’, this paperattempts to explore further, the actual physicalrealization of an all-plasmonic chip. In this paper,various methods of plasmon-basedphotolithography have been discussed and anobservation is made w.r.t the cost effectiveness andease of adaptability. Also, plasmonics based activeelement has been discussed which would helpunravel further arenas ofapproaches and methodstowards the realization of an all-plasmonic chip.

  20. Graphene-based nanodynamometer

    OpenAIRE

    Poklonski, N. A.; Siahlo, A. I.; Vyrko, S. A.; Popov, A. M.; Lozovik, Yu. E.; Lebedeva, I. V.; Knizhnik, A. A.

    2013-01-01

    A new concept of an electromechanical nanodynamometer based on the relative displacement of layers of bilayer graphene is proposed. In this nanodynamometer, force acting on one of the graphene layers causes the relative displacement of this layer and related change of conductance between the layers. Such a force can be determined by measurements of the tunneling conductance between the layers. Dependences of the interlayer interaction energy and the conductance between the graphene layers on ...

  1. Molecule-based magnets

    Indian Academy of Sciences (India)

    J V Yakhmi

    2009-06-01

    The conventional magnetic materials used in current technology, such as, Fe, Fe2O3, Cr2O3, SmCo5, Nd2Fe14B etc are all atom-based, and their preparation/processing require high temperature routes. Employing self-assembly methods, it is possible to engineer a bulk molecular material with long-range magnetic order, mainly because one can play with the weak intermolecular interactions. Since the first successful synthesis of molecular magnets in 1986, a large variety of them have been synthesized, which can be categorized on the basis of the chemical nature of the magnetic units involved: organic-, metal-based systems, heterobimetallic assemblies, or mixed organic–inorganic systems. The design of molecule-based magnets has also been extended to the design of poly-functional molecular magnets, such as those exhibiting second-order optical nonlinearity, liquid crystallinity, or chirality simultaneously with long-range magnetic order. Solubility, low density and biocompatibility are attractive features of molecular magnets. Being weakly coloured, unlike their opaque classical magnet ‘cousins’ listed above, possibilities of photomagnetic switching exist. Persistent efforts also continue to design the ever-elusive polymer magnets towards applications in industry. While providing a brief overview of the field of molecular magnetism, this article highlights some recent developments in it, with emphasis on a few studies from the author’s own lab.

  2. Internet Based Social Lending

    Directory of Open Access Journals (Sweden)

    Harsh Dhand

    2008-08-01

    Full Text Available Social lending is community-based lending. The “family and friends” loans community has been extended and formalized to create a marketplace of borrowers and lenders. In Internet-based Social Lending (IBSL, the company runs a website that connects potential lenders with potential borrowers. By removing the overheads and bulky infrastructure of the banking system, IBSL provides lenders a higher rate of return in exchange for only slightly higher risk. Borrowers here are those who are unsatisfied with the rates offered by banks or those that fall outside of the traditional banking systems due to unattractive credit ratings, high risk profiles or project-based, sporadic compensation. Borrowers are also attracted by the possibility of getting lower interest rates. We believe that this has the potential to impact the genesis of many small and medium level enterprises, besides providing a perennial source of financial leverage. The focus of this paper is not just the underlying technology and innovation, but also the market it creates. We take the example of one of the key players in the field, Zopa, and study its organization

  3. Microbead agglutination based assays

    KAUST Repository

    Kodzius, Rimantas

    2013-01-21

    We report a simple and rapid room temperature assay for point-of-care (POC) testing that is based on specific agglutination. Agglutination tests are based on aggregation of microbeads in the presence of a specific analyte thus enabling the macroscopic observation. Such tests are most often used to explore antibody-antigen reactions. Agglutination has been used for protein assays using a biotin/streptavidin system as well as a hybridization based assay. The agglutination systems are prone to selftermination of the linking analyte, prone to active site saturation and loss of agglomeration at high analyte concentrations. We investigated the molecular target/ligand interaction, explaining the common agglutination problems related to analyte self-termination, linkage of the analyte to the same bead instead of different microbeads. We classified the agglutination process into three kinds of assays: a two- component assay, a three-component assay and a stepped three- component assay. Although we compared these three kinds of assays for recognizing DNA and protein molecules, the assay can be used for virtually any molecule, including ions and metabolites. In total, the optimized assay permits detecting analytes with high sensitivity in a short time, 5 min, at room temperature. Such a system is appropriate for POC testing.

  4. Location-based games

    DEFF Research Database (Denmark)

    Ejsing-Duun, Stine

    In this dissertation, it is explored which prerequisites are necessary in location-based games (LBGs) to make meaningful the meeting between players and spatiality with an emphasis on physical locations. Throughout the dissertation, it has been shown that LBGs affect players’ perception of and be......In this dissertation, it is explored which prerequisites are necessary in location-based games (LBGs) to make meaningful the meeting between players and spatiality with an emphasis on physical locations. Throughout the dissertation, it has been shown that LBGs affect players’ perception...... experiences of being in the world and the creation of meaning. The theory on motivation defines what motivation consists of and how it relates to our actions. This theory has been combined with theories concerning play and play culture, digital media, (digital) games, (optimal) experiences, landscape...... architecture, everyday practices (related to walking in the city), and the existing theories on LBGs as well as pervasive games. The methodological approach incorporates design-based research. It combines and aims at improving design, research, and practice concurrently. A design of an LBG – Visions of Sara...

  5. Knowledge-based utility

    International Nuclear Information System (INIS)

    This presentation provides industry examples of successful marketing practices by companies facing deregulation and competition. The common thread through the examples is that long term survival of today's utility structure is dependent on the strategic role of knowledge. As opposed to regulated monopolies which usually own huge physical assets and have very little intelligence about their customers, unregulated enterprises tend to be knowledge-based, characterized by higher market value than book value. A knowledge-based enterprise gathers data, creates information and develops knowledge by leveraging it as a competitive weapon. It institutionalizes human knowledge as a corporate asset for use over and over again by the use of databases, computer networks, patents, billing, collection and customer services (BCCS), branded interfaces and management capabilities. Activities to become knowledge-based such as replacing inventory/fixed assets with information about material usage to reduce expenditure and achieve more efficient operations, and by focusing on integration and value-adding delivery capabilities, were reviewed

  6. Route based forecasting

    Science.gov (United States)

    Zuurendonk, I. W.; Wokke, M. J. J.

    2009-09-01

    Road surface temperatures can differ several degrees on a very short distance due to local effects. In order to get more insight in the local temperature differences and to develop safer gritting routes, Meteogroup has developed a system for route based temperature forecasting. The standard version of the road model is addressed to forecast road surface temperature and condition for a specific location. This model consists of two parts. First a physical part, based on the energy balance equations. The second part of the model performs a statistical correction on the calculated physical road surface temperature. The road model is able to create a forecast for one specific location. From infrared measurements, we know that large local differences in road surface temperature exist on a route. Differences can be up to 5 degrees Celsius over a distance of several hundreds of meters. Based on those measurements, the idea came up to develop a system that forecasts road surface temperature and condition for an entire route: route based forecasting. The route is split up in sections with equal properties. For each section a temperature and condition will be calculated. The main factors that influence the road surface temperature are modelled in this forecasting system: •The local weather conditions: temperature, dew point temperature, wind, precipitation, weather type, cloudiness. •The sky view: A very sheltered place will receive less radiation during daytime and emit less radiation during nighttime. For a very open spot, the effects are reversed. •The solar view: A road section with trees on the southern side, will receive less solar radiation during daytime than a section with tress on the southern side. The route based forecast shows by means of a clear Google Maps presentation which sections will be slippery at what time of the coming night. The final goal of this type of forecast, is to make dynamical gritting possible: a variable salt amount and a different

  7. Polyolefin-Based Aerogels

    Science.gov (United States)

    Lee, Je Kyun; Gould, George

    2012-01-01

    An organic polybutadiene (PB) rubberbased aerogel insulation material was developed that will provide superior thermal insulation and inherent radiation protection, exhibiting the flexibility, resiliency, toughness, and durability typical of the parent polymer, yet with the low density and superior insulation properties associated with the aerogels. The rubbery behaviors of the PB rubber-based aerogels are able to overcome the weak and brittle nature of conventional inorganic and organic aerogel insulation materials. Additionally, with higher content of hydrogen in their structure, the PB rubber aerogels will also provide inherently better radiation protection than those of inorganic and carbon aerogels. Since PB rubber aerogels also exhibit good hydrophobicity due to their hydrocarbon molecular structure, they will provide better performance reliability and durability as well as simpler, more economic, and environmentally friendly production over the conventional silica or other inorganic-based aerogels, which require chemical treatment to make them hydrophobic. Inorganic aerogels such as silica aerogels demonstrate many unusual and useful properties. There are several strategies to overcoming the drawbacks associated with the weakness and brittleness of silica aerogels. Development of the flexible fiber-reinforced silica aerogel composite blanket has proven one promising approach, providing a conveniently fielded form factor that is relatively robust toward handling in industrial environments compared to silica aerogel monoliths. However, the flexible silica aerogel composites still have a brittle, dusty character that may be undesirable, or even intolerable, in certain applications. Although the cross-linked organic aerogels such as resorcinol-formaldehyde (RF), polyisocyanurate, and cellulose aerogels show very high impact strength, they are also very brittle with little elongation (i.e., less rubbery). Also, silica and carbon aerogels are less efficient

  8. Characteristics Data Base

    International Nuclear Information System (INIS)

    The LWR Serial Numbers Database System (SNDB) contains detailed data about individual, historically discharged LWR spent fuel assemblies. This data includes the reactor where used, the year the assemblies were discharged, the pool where they are currently stored, assembly type, burnup, weight, enrichment, and an estimate of their radiological properties. This information is distributed on floppy disks to users in the nuclear industry to assist in planning for the permanent nuclear waste repository. This document describes the design and development of the SNDB. It provides a complete description of the file structures and an outline of the major code modules. It serves as a reference for a programmer maintaining the system, or for others interested in the technical detail of this database. This is the initial version of the SNDB. It contains historical data through December 31, 1987, obtained from the Energy Information Administration (EIA). EIA obtains the data from the utility companies via the RW-859 Survey Form. It evaluates and standardizes the data and distributes the resulting batch level database as a large file on magnetic tape. The Characteristics Data Base obtains this database for use in the LWR Quantities Data Base. Additionally, the CDB obtains the individual assembly level detail from EIA for use in the SNDB. While the Quantities Data Base retains only the level of detail necessary for its reporting, the SNDB does retain and use the batch level data to assist in the identification of a particular assembly serial number. We expect to update the SNDB on an annual basis, as new historical data becomes available

  9. Sustainability Base Construction Update

    Science.gov (United States)

    Mewhinney, Michael

    2012-01-01

    Construction of the new Sustainability Base Collaborative support facility, expected to become the highest performing building in the federal government continues at NASA's Ames Research Center, Moffet Field, Calif. The new building is designed to achieve a platinum rating under the leadership in Energy and Environment Design (LEED) new construction standards for environmentally sustainable construction developed by the U. S. Green Building Council, Washington, D. C. When completed by the end of 2011, the $20.6 million building will feature near zero net energy consumption, use 90 percent less potable water than conventionally build buildings of equivalent size, and will result in reduced building maintenance costs.

  10. Refractive index based measurements

    DEFF Research Database (Denmark)

    2014-01-01

    In a method for performing a refractive index based measurement of a property of a fluid such as chemical composition or temperature by observing an apparent angular shift in an interference fringe pattern produced by back or forward scattering interferometry, ambiguities in the measurement caused...... by the apparent shift being consistent with one of a number of numerical possibilities for the real shift which differ by 2n are resolved by combining measurements performed on the same sample using light paths therethrough of differing lengths....

  11. Problem Based Game Design

    DEFF Research Database (Denmark)

    Reng, Lars; Schoenau-Fog, Henrik

    2011-01-01

    At Aalborg University’s department of Medialogy, we are utilizing the Problem Based Learning method to encourage students to solve game design problems by pushing the boundaries and designing innovative games. This paper is concerned with describing this method, how students employ it in various...... projects and how they learn to analyse, design, and develop for innovation by using it. We will present various cases to exemplify the approach and focus on how the method engages students and aspires for innovation in digital entertainment and games....

  12. COMPUTER BASED ENVIRONMENT CONTROLS

    OpenAIRE

    Macoveiciuc Pastorel

    2011-01-01

    The aim of these notes is to give an overview of the main activities of computer based activities controls. The basic principles of computer controls should be common to all sectors and to most types of hardware and software. The absence of a common definition of computer control may, in part, be due to the relative newness of computer controls. A key feature of many organisations today is change. Although not necessarily the driver of change, IT is invariably an intrinsec component and much ...

  13. Vision-based interaction

    CERN Document Server

    Turk, Matthew

    2013-01-01

    In its early years, the field of computer vision was largely motivated by researchers seeking computational models of biological vision and solutions to practical problems in manufacturing, defense, and medicine. For the past two decades or so, there has been an increasing interest in computer vision as an input modality in the context of human-computer interaction. Such vision-based interaction can endow interactive systems with visual capabilities similar to those important to human-human interaction, in order to perceive non-verbal cues and incorporate this information in applications such

  14. Barium zirconate base ceramics

    International Nuclear Information System (INIS)

    The chemical corrosion at high temperatures is a serious problem in the refractory materials field, leading to degradation and bath contamination by elements of the refractory. The main objective of this work was to search for ceramics that could present higher resistance to chemical attack by aggressive molten oxides. The general behaviour of a ceramic material based on barium zirconate (Ba Zr O3) with the addition of different amounts of liquid phase former was investigated. The densification behaviour occurred during different heat treatments, as well as the microstructure development, as a function of the additives and their reactions with the main phase, were observed and are discussed. (author)

  15. Microcontroller based electronic load

    International Nuclear Information System (INIS)

    A microcontroller based electronic load has been designed and developed for testing of power supplies in CAT, Indore. This system is designed to operate in 4 different modes viz. constant current, constant power, constant resistance and constant resistance-inductance mode. This dynamic electronic load is very useful because a single load can be used in four different modes and different values can be emulated in each mode. It can be used as a switching load too. User interface has been provided to set the mode of operation and the set point during run time. (author)

  16. Speckle-based wavemeter

    DEFF Research Database (Denmark)

    Hanson, Steen Grüner; Jakobsen, Michael Linde; Chakrabarti, Maumita

    2015-01-01

    A spectrometer based on the application of dynamic speckles will be disclosed. The method relies on scattering of primarily coherent radiation from a slanted rough surface. The scattered radiation is collected on a detector array and the speckle displacement is monitored during a change in the...... incident wavelength. The change of wavelength gives an almost linear phaseshift across the scattering surface resulting in an almost linear shift of the speckle pattern, which is subsequently monitored. It is argued that frequency changes close to 100 MHz can be probed using a common CMOS array...

  17. Teradata data base computer

    Energy Technology Data Exchange (ETDEWEB)

    1984-04-01

    To meet the growing demand for information management of large databases, Teradata Corporation has introduced the DBC/1012 data base computer, an IBM plug-compatible system that can handle data volumes up to a trillion bytes. Teradata estimates the DBC/1012 to be one-third the cost of an all-software relational system on a general purpose mainframe. Cost effectiveness, as well as fault tolerance, is achieved by a parallel architecture which processes data asynchronously using multiple independent microprocessors. Another cost saving results from the resources on the host mainframe that become available once the mainframe is relieved of the burden of maintaining the database.

  18. Wood-Based Bioenergy

    OpenAIRE

    Hoel, Michael; Sletten, Thea Marcelia

    2014-01-01

    During recent years increased attention has been given to second-generation wood-based bioenergy. The carbon stored in the forest is highest when there is little or no harvest from the forest. Increasing the harvest from a forest, in order to produce more bioenergy, may thus conflict with the direct benefit of the forest as a carbon sink. We analyze this conflict using a simple model where bioenergy and fossil energy are perfect substitutes. Our analysis shows how the social optimum will depe...

  19. OCR Based Pixel Fusion

    Directory of Open Access Journals (Sweden)

    Rami Al-Hmouz

    2012-01-01

    Full Text Available Character recognition is the process that allows the automatic identification of character images, which is generally referred as Optical Character Recognition (OCR. The characters are either handwritten or typed. This study proposed a novel OCR approach based on the likelihood functions of pixels, which were obtained by averaging a trained set of character images. A Bayesian fusion process for all pixel probabilities decides the recognition of characters. Further tests using Support Vector Machine (SVM classifier were carried out on characters with the same shape. This method was used to test noisy images and achieved an accuracy of 97.95%, thus, outperforming other OCR methods.

  20. Technical Design Report BASE

    CERN Document Server

    Ulmer, S; Smorra, C; Blaum, K; Franke, K; Matsuda, Y; Nagahama, H; Quint, W; Walz, J; Mooser, A; Schneider, G; CERN. Geneva. SPS and PS Experiments Committee; SPSC

    2013-01-01

    We propose a direct high-precision measurement of the magnetic moment, or g-factor, of a single antiproton stored in a cryogenic Penning trap. Currently the most precise value of the magnetic moment of the antiproton is extracted from super-hyperfine spectroscopy of antiprotonic helium atoms, and known with a relative precision of only about 3 10^{-3}. BASE aims at a measurement with a relative precision of 10^{-9} or better. A Letter of Intent which was submitted to CERN was welcomed by the SPSC and we were invited to submit this Technical Design Report.

  1. Bi-based superconductor

    Directory of Open Access Journals (Sweden)

    S E Mousavi

    2009-08-01

    Full Text Available   In this paper, Bi-Sr-Ca-Cu-O (BCSCCO system superconductor is made by the solid state reaction method. The effect of doping Pb, Cd, Sb, Cu and annealing time on the critical temperature and critical current density have been investigated. The microstructure and morphology of the samples have been studied by X-ray diffraction, scanning electron microscope and energy dispersive X-ray. The results show that the fraction of Bi-2223 phase in the Bi- based superconductor, critical temperature and critical current density depend on the annealing temperature, annealing time and the kind and amount of doping .

  2. Agent-Based Optimization

    CERN Document Server

    Jędrzejowicz, Piotr; Kacprzyk, Janusz

    2013-01-01

    This volume presents a collection of original research works by leading specialists focusing on novel and promising approaches in which the multi-agent system paradigm is used to support, enhance or replace traditional approaches to solving difficult optimization problems. The editors have invited several well-known specialists to present their solutions, tools, and models falling under the common denominator of the agent-based optimization. The book consists of eight chapters covering examples of application of the multi-agent paradigm and respective customized tools to solve  difficult optimization problems arising in different areas such as machine learning, scheduling, transportation and, more generally, distributed and cooperative problem solving.

  3. RF Based Spy

    OpenAIRE

    Robot Prerna Jain; Pallavi N. Firke

    2014-01-01

    The intention of this paper is to reduce human victims in terrorist attack such as 26/11. So this problem can be overcome by designing the RF based spy robot which involves wireless camera. so that from this we can examine rivals when it required. This robot can quietly enter into enemy area and sends us the information via wireless camera. On the other hand one more feature is added in this robot that is colour sensor. Colour sensor senses the colour of surface and according ...

  4. Mars base buildup scenarios

    International Nuclear Information System (INIS)

    Two surface base build-up scenarios are presented in order to help visualize the mission and to serve as a basis for trade studies. In the first scenario, direct manned landings on the Martian surface occur early in the missions and scientific investigation is the main driver and rationale. In the second scenario, early development of an infrastructure to exploite the volatile resources of the Martian moons for economic purposes is emphasized. Scientific exploration of the surface is delayed at first, but once begun develops rapidly aided by the presence of a permanently manned orbital station

  5. Alphavirus-Based Vaccines.

    Science.gov (United States)

    Lundstrom, Kenneth

    2016-01-01

    Alphavirus vectors based on Semliki Forest virus, Sindbis virus, and Venezuelan equine encephalitis virus have been widely applied for vaccine development. Naked RNA replicons, recombinant viral particles, and layered DNA vectors have been subjected to immunization in preclinical animal models with antigens for viral targets and tumor antigens. Moreover, a limited number of clinical trials have been conducted in humans. Vaccination with alphavirus vectors has demonstrated efficient immune responses and has showed protection against challenges with lethal doses of virus and tumor cells, respectively. Moreover, vaccines have been developed against alphaviruses causing epidemics such as Chikungunya virus. PMID:27076308

  6. WAP - based telemedicine applications

    International Nuclear Information System (INIS)

    Telemedicine refers to the utilization of telecommunication technology for medical diagnosis, treatment, and patient care. Its aim is to provide expert-based health care to remote sites through telecommunication and information technologies. The significant advances in technologies have enabled the introduction of a broad range of telemedicine applications, which are supported by computer networks, wireless communication, and information superhighway. For example, some hospitals are using tele-radiology for remote consultation. Such a system includes medical imaging devices networked with computers and databases. Another growing area is patient monitoring, in which sensors are used to acquire biomedical signals, such as electrocardiogram (ECG), blood pressure, and body temperature, from a remote patient, who could be in bed or moving freely. The signals are then relayed to remote systems for viewing and analysis. Telemedicine can be divided into two basic modes of operations: real-time mode, in which the patient data can be accessed remotely in real-time, and store-and-forward mode, in which the acquired data does not have to be accessed immediately. In the recent years, many parties have demonstrated various telemedicine applications based on the Internet and cellular phone as these two fields have been developing rapidly. A current, recognizable trend in telecommunication is the convergence of wireless communication and computer network technologies. This has been reflected in recently developed telemedicine systems. For example, in 1998 J. Reponen, et al. have demonstrated transmission and display of computerized tomography (CT) examinations using a remote portable computer wirelessly connected to a computer network through TCP/IP on a GSM cellular phone. Two years later, they carried out the same tests with a GSM-based wireless personal digital assistant (PDA). The WAP (Wireless Application Protocol) Forum was founded in 1997 to create a global protocol

  7. Cellular based cancer vaccines

    DEFF Research Database (Denmark)

    Hansen, Morten; Met, O; Svane, I M;

    2012-01-01

    Cancer vaccines designed to re-calibrate the existing host-tumour interaction, tipping the balance from tumor acceptance towards tumor control holds huge potential to complement traditional cancer therapies. In general, limited success has been achieved with vaccines composed of tumor...... in vitro migration via autocrine receptor-mediated endocytosis of CCR7. In the current review, we discuss optimal design of DC maturation focused on pre-clinical as well as clinical results from standard and polarized dendritic cell based cancer vaccines....

  8. Pitch Based Sound Classification

    OpenAIRE

    Nielsen, Andreas Brinch; Hansen, Lars Kai; Kjems, U.

    2006-01-01

    A sound classification model is presented that can classify signals into music, noise and speech. The model extracts the pitch of the signal using the harmonic product spectrum. Based on the pitch estimate and a pitch error measure, features are created and used in a probabilistic model with soft-max output function. Both linear and quadratic inputs are used. The model is trained on 2 hours of sound and tested on publicly available data. A test classification error below 0.05 with 1 s classif...

  9. Moon base reactor system

    Science.gov (United States)

    Chavez, H.; Flores, J.; Nguyen, M.; Carsen, K.

    1989-01-01

    The objective of our reactor design is to supply a lunar-based research facility with 20 MW(e). The fundamental layout of this lunar-based system includes the reactor, power conversion devices, and a radiator. The additional aim of this reactor is a longevity of 12 to 15 years. The reactor is a liquid metal fast breeder that has a breeding ratio very close to 1.0. The geometry of the core is cylindrical. The metallic fuel rods are of beryllium oxide enriched with varying degrees of uranium, with a beryllium core reflector. The liquid metal coolant chosen was natural lithium. After the liquid metal coolant leaves the reactor, it goes directly into the power conversion devices. The power conversion devices are Stirling engines. The heated coolant acts as a hot reservoir to the device. It then enters the radiator to be cooled and reenters the Stirling engine acting as a cold reservoir. The engines' operating fluid is helium, a highly conductive gas. These Stirling engines are hermetically sealed. Although natural lithium produces a lower breeding ratio, it does have a larger temperature range than sodium. It is also corrosive to steel. This is why the container material must be carefully chosen. One option is to use an expensive alloy of cerbium and zirconium. The radiator must be made of a highly conductive material whose melting point temperature is not exceeded in the reactor and whose structural strength can withstand meteor showers.

  10. Accelerator-based BNCT

    International Nuclear Information System (INIS)

    The activity in accelerator development for accelerator-based BNCT (AB-BNCT) both worldwide and in Argentina is described. Projects in Russia, UK, Italy, Japan, Israel, and Argentina to develop AB-BNCT around different types of accelerators are briefly presented. In particular, the present status and recent progress of the Argentine project will be reviewed. The topics will cover: intense ion sources, accelerator tubes, transport of intense beams, beam diagnostics, the 9Be(d,n) reaction as a possible neutron source, Beam Shaping Assemblies (BSA), a treatment room, and treatment planning in realistic cases. - Highlights: • The activity in accelerator development for accelerator-based BNCT (AB-BNCT) both worldwide and in Argentina is described. • Projects in Russia, UK, Italy, Japan, Israel, and Argentina to develop AB-BNCT around different types of accelerators are briefly presented. • The present status and recent progress of the Argentine project will be reviewed. • Topics cover intense ion sources, accelerator tubes, transport of intense beams and beam diagnostics, among others

  11. Model Based Definition

    Science.gov (United States)

    Rowe, Sidney E.

    2010-01-01

    In September 2007, the Engineering Directorate at the Marshall Space Flight Center (MSFC) created the Design System Focus Team (DSFT). MSFC was responsible for the in-house design and development of the Ares 1 Upper Stage and the Engineering Directorate was preparing to deploy a new electronic Configuration Management and Data Management System with the Design Data Management System (DDMS) based upon a Commercial Off The Shelf (COTS) Product Data Management (PDM) System. The DSFT was to establish standardized CAD practices and a new data life cycle for design data. Of special interest here, the design teams were to implement Model Based Definition (MBD) in support of the Upper Stage manufacturing contract. It is noted that this MBD does use partially dimensioned drawings for auxiliary information to the model. The design data lifecycle implemented several new release states to be used prior to formal release that allowed the models to move through a flow of progressive maturity. The DSFT identified some 17 Lessons Learned as outcomes of the standards development, pathfinder deployments and initial application to the Upper Stage design completion. Some of the high value examples are reviewed.

  12. Design Based Wilderness Education

    Directory of Open Access Journals (Sweden)

    Christopher R. Saulnier

    2015-02-01

    Full Text Available The Massachusetts Institute of Technology (MIT has been collaborating since 2010 with the Singapore Ministry of Education to help develop the Singapore University of Technology and Design (SUTD. One element of this collaboration, the Global Leadership Program (GLP, aims to provide SUTD students with the opportunity to interact with the MIT community and experience MIT’s academic culture. During GLP students participate in a program designed to develop leadership ability while also increasing their understanding of engineering science and design thinking. This paper introduces a curriculum combining the pedagogies of design-based learning and wilderness education that was implemented in the summer of 2014 to holistically address the development of these three competencies. Through design-based learning activities, both for and in a natural environment, students were encouraged to develop competencies in engineering science and engineering design while exploring the diverse attributes essential for success as an engineer. This paper examines the results of a retrospective post-then-pre survey administered to the participants upon completion of the program to explore the effects of the program on the development of professional engineering competencies. We find a statistically significant increase in items associated with Individual Leadership Skill, Group Leadership Skill and the role of Society and the Economy. These results are triangulated with student exit interviews and instructor observations.

  13. Challenge Based Innovation gala

    CERN Document Server

    CERN. Geneva; Utriainen, Tuuli Maria; Toivonen, Harri; Nordberg, Markus

    2014-01-01

    Challenge Based Innovation gala   There’s a new experiment starting in CERN called IdeaLab where we work together with detector R&D researchers to help them to bridge their knowledge into a more human, societally oriented context. Currently we are located in B153, but will move our activities to a new facility next to the Globe in May 2014. One of our first pilot projects is a 5 month course CBI (Challenge Based Innovation) where two multidisciplinary student teams join forces with Edusafe & TALENT projects at CERN. Their goal is to discover what kind of tools for learning could be created in collaboration with the two groups. After months of user interviews and low resolution prototyping they are ready to share the results with us in the form of an afternoon gala. We warmly welcome you to join us to see the students' results and experience the prototypes they have conceived. The event is in three parts, you are welcome to visit all of them,...

  14. Microlaser-based displays

    Science.gov (United States)

    Bergstedt, Robert; Fink, Charles G.; Flint, Graham W.; Hargis, David E.; Peppler, Philipp W.

    1997-07-01

    Laser Power Corporation has developed a new type of projection display, based upon microlaser technology and a novel scan architecture, which provides the foundation for bright, extremely high resolution images. A review of projection technologies is presented along with the limitations of each and the difficulties they experience in trying to generate high resolution imagery. The design of the microlaser based projector is discussed along with the advantage of this technology. High power red, green, and blue microlasers have been designed and developed specifically for use in projection displays. These sources, in combination with high resolution, high contrast modulator, produce a 24 bit color gamut, capable of supporting the full range of real world colors. The new scan architecture, which reduces the modulation rate and scan speeds required, is described. This scan architecture, along with the inherent brightness of the laser provides the fundamentals necessary to produce a 5120 by 4096 resolution display. The brightness and color uniformity of the display is excellent, allowing for tiling of the displays with far fewer artifacts than those in a traditionally tiled display. Applications for the display include simulators, command and control centers, and electronic cinema.

  15. Knowledge Based Economy Assessment

    Directory of Open Access Journals (Sweden)

    Madalina Cristina Tocan

    2012-12-01

    Full Text Available The importance of knowledge-based economy (KBE in the XXI century isevident. In the article the reflection of knowledge on economy is analyzed. The main point is targeted to the analysis of characteristics of knowledge expression in economy and to the construction of structure of KBE expression. This allows understanding the mechanism of functioning of knowledge economy. Theauthors highlight the possibility to assess the penetration level of KBE which could manifest itself trough the existence of products of knowledge expression which could be created in acquisition, creation, usage and development of them. The latter phenomenon is interpreted as knowledge expression characteristics: economic and social context, human resources, ICT, innovative business and innovation policy. The reason for this analysis was based on the idea that in spite of the knowledge economy existence in all developed World countries adefinitive, universal list of indicators for mapping and measuring the KBE does not yet exists. Knowledge Expression Assessment Models are presented in the article.

  16. Constraint-based reachability

    Directory of Open Access Journals (Sweden)

    Arnaud Gotlieb

    2013-02-01

    Full Text Available Iterative imperative programs can be considered as infinite-state systems computing over possibly unbounded domains. Studying reachability in these systems is challenging as it requires to deal with an infinite number of states with standard backward or forward exploration strategies. An approach that we call Constraint-based reachability, is proposed to address reachability problems by exploring program states using a constraint model of the whole program. The keypoint of the approach is to interpret imperative constructions such as conditionals, loops, array and memory manipulations with the fundamental notion of constraint over a computational domain. By combining constraint filtering and abstraction techniques, Constraint-based reachability is able to solve reachability problems which are usually outside the scope of backward or forward exploration strategies. This paper proposes an interpretation of classical filtering consistencies used in Constraint Programming as abstract domain computations, and shows how this approach can be used to produce a constraint solver that efficiently generates solutions for reachability problems that are unsolvable by other approaches.

  17. BIOMETRICS BASED USER AUTHENTICATION

    Directory of Open Access Journals (Sweden)

    Tanuj Tiwari

    2015-10-01

    Full Text Available Biometrics is automated methods of recognizing a person based on a physiological or behavioral characteristic. Biometrics technologies are base for a plethora of highly secure identification and personal verification solutions. It is measurement of biological characteristics – either physiological or behavioral – that verify the claimed identity of an individual. Physiological biometrics include fingerprints, iris recognition. voice verification, retina recognition, palm vein patterns, finger vein patterns, hand geometry and DNA But there arises a need for more robust systems in order to tackle the increasing incidents of security breaches and frauds. So there is always a need for fool proof technology that can provide security and safety to individuals and the transactions that the individuals make. Biometrics is increasingly used by organizations to verify identities, but coupled with quantum cryptography it offers a new range of security benefits with quantum cryptography where we form a key when we need it and then destroy it. In this paper, we give a brief overview of the field of biometrics and summarize some of its advantages, disadvantages, strengths, limitations, and related privacy concerns.

  18. Workplace Based Assessment in Psychiatry

    OpenAIRE

    Ayse Devrim Basterzi; O. Surel Karabilgin

    2009-01-01

    Workplace based assessment refers to the assessment of working practices based on what doctors actually do in the workplace, and is predominantly carried out in the workplace itself. Assessment drives learning and it is therefore essential that workplace-based assessment focuses on important attributes rather than what is easiest to assess. Workplacebased assessment is usually competency based. Workplace based assesments may well facilitate and enhance various aspects of educational supervisi...

  19. MS Based Metabonomics

    Energy Technology Data Exchange (ETDEWEB)

    Want, Elizabeth J.; Metz, Thomas O.

    2010-03-01

    Metabonomics is the latest and least mature of the systems biology triad, which also includes genomics and proteomics, and has its origins in the early orthomolecular medicine work pioneered by Linus Pauling and Arthur Robinson. It was defined by Nicholson and colleagues in 1999 as the quantitative measurement of perturbations in the metabolite complement of an integrated biological system in response to internal or external stimuli, and is often used today to describe many non-global types of metabolite analyses. Applications of metabonomics are extensive and include toxicology, nutrition, pharmaceutical research and development, physiological monitoring and disease diagnosis. For example, blood samples from millions of neonates are tested routinely by mass spectrometry (MS) as a diagnostic tool for inborn errors of metabolism. The metabonome encompasses a wide range of structurally diverse metabolites; therefore, no single analytical platform will be sufficient. Specialized sample preparation and detection techniques are required, and advances in NMR and MS technologies have led to enhanced metabonome coverage, which in turn demands improved data analysis approaches. The role of MS in metabonomics is still evolving as instrumentation and software becomes more sophisticated and as researchers realize the strengths and limitations of current technology. MS offers a wide dynamic range, high sensitivity, and reproducible, quantitative analysis. These attributes are essential for addressing the challenges of metabonomics, as the range of metabolite concentrations easily exceeds nine orders of magnitude in biofluids, and the diversity of molecular species ranges from simple amino and organic acids to lipids and complex carbohydrates. Additional challenges arise in generating a comprehensive metabolite profile, downstream data processing and analysis, and structural characterization of important metabolites. A typical workflow of MS-based metabonomics is shown in Figure

  20. Space-Based Range

    Science.gov (United States)

    2008-01-01

    Space-Based Range (SBR), previously known as Space-Based Telemetry and Range Safety (STARS), is a multicenter NASA proof-of-concept project to determine if space-based communications using NASA's Tracking and Data Relay Satellite System (TDRSS) can support the Range Safety functions of acquiring tracking data and generating flight termination signals, while also providing broadband Range User data such as voice, video, and vehicle/payload data. There was a successful test of the Range Safety system at Wallops Flight Facility (WFF) on December 20, 2005, on a two-stage Terrier-Orion spin-stabilized sounding rocket. SBR transmitted GPS tracking data and maintained links with two TDRSS satellites simultaneously during the 10-min flight. The payload section deployed a parachute, landed in the Atlantic Ocean about 90 miles downrange from the launch site, and was successfully recovered. During the Terrier-Orion tests flights, more than 99 percent of all forward commands and more than 95 percent of all return frames were successfully received and processed. The time latency necessary for a command to travel from WFF over landlines to White Sands Complex and then to the vehicle via TDRSS, be processed onboard, and then be sent back to WFF was between 1.0 s and 1.1 s. The forward-link margins for TDRS-10 (TDRS East [TDE]) were 11 dB to 12 dB plus or minus 2 dB, and for TDRS-4 (TDRS Spare [TDS]) were 9 dB to 10 dB plus or minus 1.5 dB. The return-link margins for both TDE and TDS were 6 dB to 8 dB plus or minus 3 dB. There were 11 flights on an F-15B at Dryden Flight Research Center (DFRC) between November 2006 and February 2007. The Range User system tested a 184-element TDRSS Ku-band (15 GHz) phased-array antenna with data rates of 5 Mbps and 10 Mbps. This data was a combination of black-and-white cockpit video, Range Safety tracking and transceiver data, and aircraft and antenna controller data streams. IP data formatting was used.

  1. Nanocrystalline copper based microcomposites

    Directory of Open Access Journals (Sweden)

    J.P. Stobrawa

    2012-09-01

    Full Text Available Purpose: The aim of this work was to investigate microstructure, mechanical properties and deformation behavior of copper microcomposites: Cu- Y2O3, Cu- ZrO2 and Cu-WC produced by powder metallurgy techniques.Design/methodology/approach: Tests were made with Cu-Y2O3, Cu-ZrO2 and Cu-WC microcomposites containing up to 2% of a strengthening phase. The materials were fabricated by powder metallurgy techniques, including milling of powders, followed by their compacting and sintering. The main mechanical properties of the materials were determined from the compression test and, additionally, measurements of HV hardness and electrical conductivity were made. Analysis of the initial nanocrystalline structure of these materials was made and its evolution during sintering and cold deformation was investigated.Findings: It was found out that addition of up to 2 wt.% of a strengthening phase significantly improves mechanical properties of the material and increases its softening point. The obtained strengthening effect have been discussed based on the existing theories related to strengthening of nanocrystalline materials. The studies have shown importance of “flows” existing in the consolidated materials and sintered materials in pores or regions of poor powder particle connection which significantly deteriorate the mechanical properties of microcomposites produced by powder metallurgy.Research limitations/implications: The powder metallurgy techniques make it possible to obtain copperbased bulk materials by means of input powder milling in a planetary ball mill, followed by compacting and sintering. Additional operations of hot extrusion are also often used. There is some danger, however, that during high-temperature processing or application of these materials at elevated or high temperatures this nanometric structure may become unstable.Practical implications: A growing trend to use new copper based microcomposites is observed recently worldwide

  2. Mucin-Based Vaccines

    Science.gov (United States)

    Richardson, Jonathan P.; MacMillan, Derek

    Mucins are heavily O-glycosylated cell surface and secreted glycoproteins . In addition to orchestrating cell-extracellular matrix and cell-cell interactions in healthy organisms mucins are also the major carriers of altered glycosylation in carcinomas. Tumor-associated antigens displayed by cancer cells comprise oligosaccharide and glycopeptide motifs not encountered in the same locale or at the same frequency in healthy cells, and potentially confer a selective advantage to the tumor. Frequently tumor-associated antigens are under-glycosylated and prematurely sialylated, and it is these relatively simple saccharide and glycopeptide structures that have been targeted to serve as drug candidates in most cases. A major goal is to assemble glycopeptide vaccine candidates based on partial mucin sequences and displaying tumor-associated antigens that can mount a potent immunological tumor-specific response when, in reality, the tumor has already coerced the immune system into a state of co-existence.

  3. Situation based housing

    DEFF Research Database (Denmark)

    Duelund Mortensen, Peder; Welling, Helen; Wiell Nordberg, Lene;

    2007-01-01

    variety of approaches to these goals. This working paper reviews not only a selection of new housing types, but also dwellings from the past, which each contain an aspect of changeability. Our study is based on information from users in the selected housing schemes, gathered from questionnaires...... the average family's lifestyle. These dwellings were ground-breaking when they were built, but today are clearly a product of their time. The reaction to functionalism and the postwar mass production gave rise to flexible dwelling with countless possibilities for room division. The housing of this...... period has characteristics which in the long run have proven to be unfortunate both in terms in terms of durability and architectural quality. Today there is a focus on the development of more open and functionally non-determined housing. A number of new housing schemes in and around Copenhagen reveal a...

  4. Touching base with OPERA

    CERN Multimedia

    CERN Bulletin

    2011-01-01

    Three seminars – at CERN, at Gran Sasso and in Japan – and an article calling for the scrutiny of the scientific community: the OPERA Collaboration opened its research publicly. In addition to huge press coverage, this triggered welcome reactions from colleagues around the world, many of whom will attempt to independently interpret and reproduce the measurement. OPERA’s Spokesperson touches base with the Bulletin.   The CERN Main Auditorium was crowded as OPERA Physics co-ordinator Dario Autiero presented the results of their research (23 September 2011). According to the OPERA strategy, the results of the measurements are in the hands of the scientific community and, as for any other scientific result, several months will be needed before other groups will be able to perform an independent measurement. In the meantime, the OPERA Collaboration is dealing with an avalanche of emails from the scientific community, members of the general public, and the press. &...

  5. Plasma based accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Caldwell, Allen [Max-Planck-Institut fuer Physik, Muenchen (Germany)

    2015-05-01

    The concept of laser-induced plasma wakefields as a technique to accelerate charged particles was introduced 35 years ago as a means to go beyond the accelerating gradients possible with metallic cavities supporting radio frequency electromagnetic fields. Significant developments in laser technology have made possible the pulse intensity needed to realize this concept, and rapid progress is now underway in the realization of laser-driven plasma wakefield acceleration. It has also been realized that similar accelerating gradients can be produced by particle beams propagating in plasmas, and experimental programs have also been undertaken to study this possibility. Positive results have been achieved with electron-driven plasma wakefields, and a demonstration experiment with proton-driven wakefields is under construction at CERN. The concepts behind these different schemes and their pros and cons are described, as well as the experimental results achieved. An outlook for future practical uses of plasma based accelerators will also be given.

  6. Integrated data base program

    International Nuclear Information System (INIS)

    The IDB Program provides direct support to the DOE Nuclear Waste Management and Fuel Cycle Programs and their lead sites and support contractors by providing and maintaining a current, integrated data base of spent fuel and radioactive waste inventories and projections. All major waste types (HLW, TRU, and LLW) and sources (government, commerical fuel cycle, and I/I) are included. A major data compilation was issued in September, 1981: Spent Fuel and Radioactive Waste Inventories and Projections as of December 31, 1980, DOE/NE-0017. This report includes chapters on Spent Fuel, HLW, TRU Waste, LLW, Remedial Action Waste, Active Uranium Mill Tailings, and Airborne Waste, plus Appendices with more detailed data in selected areas such as isotopics, radioactivity, thermal power, projections, and land usage. The LLW sections include volumes, radioactivity, thermal power, current inventories, projected inventories and characteristics, source terms, land requirements, and a breakdown in terms of government/commercial and defense/fuel cycle/I and I

  7. Al - BASED CAST COMPOSITES

    Directory of Open Access Journals (Sweden)

    Rakesh Kumar Yadav

    2011-08-01

    Full Text Available The economy is very important feature nowadays in themarket. The researches are playing an important role inengineering field to increase the life of machine parts /components and decrease the cost. The compositematerials have the potential to replace widely used steeland aluminium due to their good characteristics withbetter performance. The Al-based composites have foundextensive applications in automobile industries andaerospace industries due to their increased stiffness,strength, thermal conductivity and wear resistanceproperties. A number of particulate phases have beenemployed in the Al-alloy matrix. The cast aluminiumceramicparticulate composites are finding applications inpistons, connecting rods, cylinder liner, engine cylinderblock, electrical contacts etc.The present investigation isbased on study of the effect of particulate phase on theSEM study, micro-hardness, elastic modulus, tensilestrength and the wear behaviour of Al-5 % SiC-7 % Fe,Al-10 % SiC-6 % Fe and Al-15 % SiC-5 % Fe composites.

  8. Space-based detectors

    DEFF Research Database (Denmark)

    Sesana, A.; Weber, W. J.; Killow, C. J.;

    2014-01-01

    planned for 2015. This mission and its payload “LISA Technology Package” will demonstrate key technologies for LISA. In this context, reference masses in free fall for LISA, and gravitational physics in general, was described by William Weber, laser interferometry at the pico-metre level and the optical......The parallel session C5 on Space-Based Detectors gave a broad overview over the planned space missions related to gravitational wave detection. Overviews of the revolutionary science to be expected from LISA was given by Alberto Sesana and Sasha Buchman. The launch of LISA Pathfinder (LPF) is...... bench of LPF was presented by Christian Killow and the performance of the LPF optical metrology system by Paul McNamara. While LPF will not yet be sensitive to gravitational waves, it may nevertheless be used to explore fundamental physics questions, which was discussed by Michele Armano. Some parts of...

  9. Base isolation: Fresh insight

    Energy Technology Data Exchange (ETDEWEB)

    Shustov, V.

    1993-07-15

    The objective of the research is a further development of the engineering concept of seismic isolation. Neglecting the transient stage of seismic loading results in a widespread misjudgement: The force of resistance associated with velocity is mostly conceived as a source of damping vibrations, though it is an active force at the same time, during an earthquake type excitation. For very pliant systems such as base isolated structures with relatively low bearing stiffness and with artificially added heavy damping mechanism, the so called `damping`` force may occur even the main pushing force at an earthquake. Thus, one of the two basic pillars of the common seismic isolation philosophy, namely, the doctrine of usefulness and necessity of a strong damping mechanism, is turning out to be a self-deception, sometimes even jeopardizing the safety of structures and discrediting the very idea of seismic isolation. There is a way out: breaking with damping dependancy.

  10. Graphene based biosensors

    Science.gov (United States)

    Gürel, Hikmet Hakan; Salmankurt, Bahadır

    2016-03-01

    Nanometer-sized graphene as a 2D material has unique chemical and electronic properties. Because of its unique physical, chemical, and electronic properties, its interesting shape and size make it a promising nanomaterial in many biological applications. It is expected that biomaterials incorporating graphene will be developed for the graphene-based drug delivery systems and biomedical devices. The interactions of biomolecules and graphene are long-ranged and very weak. Development of new techniques is very desirable for design of bioelectronics sensors and devices. In this work, we present first-principles calculations within density functional theory to calculate effects of charging on nucleobases on graphene. It is shown that how modify structural and electronic properties of nucleobases on graphene by applied charging.

  11. PROcess Based Diagnostics PROBE

    Science.gov (United States)

    Clune, T.; Schmidt, G.; Kuo, K.; Bauer, M.; Oloso, H.

    2013-01-01

    Many of the aspects of the climate system that are of the greatest interest (e.g., the sensitivity of the system to external forcings) are emergent properties that arise via the complex interplay between disparate processes. This is also true for climate models most diagnostics are not a function of an isolated portion of source code, but rather are affected by multiple components and procedures. Thus any model-observation mismatch is hard to attribute to any specific piece of code or imperfection in a specific model assumption. An alternative approach is to identify diagnostics that are more closely tied to specific processes -- implying that if a mismatch is found, it should be much easier to identify and address specific algorithmic choices that will improve the simulation. However, this approach requires looking at model output and observational data in a more sophisticated way than the more traditional production of monthly or annual mean quantities. The data must instead be filtered in time and space for examples of the specific process being targeted.We are developing a data analysis environment called PROcess-Based Explorer (PROBE) that seeks to enable efficient and systematic computation of process-based diagnostics on very large sets of data. In this environment, investigators can define arbitrarily complex filters and then seamlessly perform computations in parallel on the filtered output from their model. The same analysis can be performed on additional related data sets (e.g., reanalyses) thereby enabling routine comparisons between model and observational data. PROBE also incorporates workflow technology to automatically update computed diagnostics for subsequent executions of a model. In this presentation, we will discuss the design and current status of PROBE as well as share results from some preliminary use cases.

  12. Base Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Everett Sondreal; John Hendrikson

    2009-03-31

    In June 2009, the Energy & Environmental Research Center (EERC) completed 11 years of research under the U.S. Department of Energy (DOE) Base Cooperative Agreement No. DE-FC26-98FT40320 funded through the Office of Fossil Energy (OFE) and administered at the National Energy Technology Laboratory (NETL). A wide range of diverse research activities were performed under annual program plans approved by NETL in seven major task areas: (1) resource characterization and waste management, (2) air quality assessment and control, (3) advanced power systems, (4) advanced fuel forms, (5) value-added coproducts, (6) advanced materials, and (7) strategic studies. This report summarizes results of the 67 research subtasks and an additional 50 strategic studies. Selected highlights in the executive summary illustrate the contribution of the research to the energy industry in areas not adequately addressed by the private sector alone. During the period of performance of the agreement, concerns have mounted over the impact of carbon emissions on climate change, and new programs have been initiated by DOE to ensure that fossil fuel resources along with renewable resources can continue to supply the nation's transportation fuel and electric power. The agreement has addressed DOE goals for reductions in CO{sub 2} emissions through efficiency, capture, and sequestration while expanding the supply and use of domestic energy resources for energy security. It has further contributed to goals for near-zero emissions from highly efficient coal-fired power plants; environmental control capabilities for SO{sub 2}, NO{sub x}, fine respirable particulate (PM{sub 2.5}), and mercury; alternative transportation fuels including liquid synfuels and hydrogen; and synergistic integration of fossil and renewable resources (e.g., wind-, biomass-, and coal-based electrical generation).

  13. The office based CHIVA

    Directory of Open Access Journals (Sweden)

    Passariello F

    2013-09-01

    Full Text Available Fausto Passariello,1 Stefano Ermini,2 Massimo Cappelli,3 Roberto Delfrate,4 Claude Franceschi5 1Centro Diagnostico Aquarius, Napoli, Italy; 2Private Practice, Grassina, Italy; 3Private Practice, Firenze, Italy; 4Casa di Cure Figlie di Maria, Cremona, Italy; 5Hospital St Joseph, Service d'Explorations Vasculaires, Paris, France Abstract: The cure Conservatrice Hémodynamique de l'Insuffisance Veineuse en Ambulatoire (CHIVA can be office based (OB. The OB-CHIVA protocol is aimed at transferring CHIVA procedures to specialists rooms. The protocol will check the feasibility of OB-CHIVA, data pertaining to recurrence, and will offer the opportunity to study saphenous femoral junction (SFJ stump evolution, the role of the washing vessels and the arch recanalization rate, and gather new data about the effect of the length of the treated saphenous vein. A simplified diagnostic procedure will allow an essential ultrasound examination of the venous net while a schematic and easily readable algorithm guides therapeutic choices. The Riobamba draining crossotomy (RDC tactic is composed of a set of OB procedures. While some of these procedures are, at the moment, only proposals, others are already applied. Devices generally used in ablative procedures such as Light Amplification by Stimulated Emission of Radiation (LASER, radio frequency, steam, and mechanical devices are used in this context to serve to conservative interventions for CHIVA. New techniques have also been proposed for devalvulation and tributary disconnection. Detailed follow-up is necessary in order to determine the effects of therapy and possible disease evolution. Finally, information is added about the informed consent and the ethical considerations of OB-CHIVA research. Keywords: CHIVA, office based procedures, LASER, RF, steam

  14. Usability Issues in Content Based Multimedia Computer Based Trainings

    OpenAIRE

    Khan, Muhammad Qasim; Rehman, Zia ur

    2009-01-01

    In distance education, students and teachers are at different places and interact with each other with the help of different technologies. Broadcast television, two-way video conferencing, asynchronous learning mode, virtual learning environment (VLE) and content based multimedia computer based trainings (CB-MCBTs) are some of the technologies used to provide distance education. Content Based Multimedia Computer Based Trainings (CB-MCBT) is a computerized learning environment. The acceptance ...

  15. Computer-based multi-channel analyzer based on internet

    International Nuclear Information System (INIS)

    Combined the technology of Internet with computer-based multi-channel analyzer, a new kind of computer-based multi-channel analyzer system which is based on browser is presented. Its framework and principle as well as its implementation are discussed

  16. Risk-based configuration control

    International Nuclear Information System (INIS)

    The presentation discusses the following issues: The Configuration Control; The Risk-based Configuration Control (during power operation mode, and during shutdown mode). PSA requirements. Use of Risk-based Configuration Control System. Configuration Management (basic elements, benefits, information requirements)

  17. Mixture Based Outlier Filtration

    Directory of Open Access Journals (Sweden)

    P. Pecherková

    2006-01-01

    Full Text Available Success/failure of adaptive control algorithms – especially those designed using the Linear Quadratic Gaussian criterion – depends on the quality of the process data used for model identification. One of the most harmful types of process data corruptions are outliers, i.e. ‘wrong data’ lying far away from the range of real data. The presence of outliers in the data negatively affects an estimation of the dynamics of the system. This effect is magnified when the outliers are grouped into blocks. In this paper, we propose an algorithm for outlier detection and removal. It is based on modelling the corrupted data by a two-component probabilistic mixture. The first component of the mixture models uncorrupted process data, while the second models outliers. When the outlier component is detected to be active, a prediction from the uncorrupted data component is computed and used as a reconstruction of the observed data. The resulting reconstruction filter is compared to standard methods on simulated and real data. The filter exhibits excellent properties, especially in the case of blocks of outliers. 

  18. Alphavirus-Based Vaccines

    Directory of Open Access Journals (Sweden)

    Kenneth Lundstrom

    2014-06-01

    Full Text Available Alphavirus vectors have demonstrated high levels of transient heterologous gene expression both in vitro and in vivo and, therefore, possess attractive features for vaccine development. The most commonly used delivery vectors are based on three single-stranded encapsulated alphaviruses, namely Semliki Forest virus, Sindbis virus and Venezuelan equine encephalitis virus. Alphavirus vectors have been applied as replication-deficient recombinant viral particles and, more recently, as replication-proficient particles. Moreover, in vitro transcribed RNA, as well as layered DNA vectors have been applied for immunization. A large number of highly immunogenic viral structural proteins expressed from alphavirus vectors have elicited strong neutralizing antibody responses in multispecies animal models. Furthermore, immunization studies have demonstrated robust protection against challenges with lethal doses of virus in rodents and primates. Similarly, vaccination with alphavirus vectors expressing tumor antigens resulted in prophylactic protection against challenges with tumor-inducing cancerous cells. As certain alphaviruses, such as Chikungunya virus, have been associated with epidemics in animals and humans, attention has also been paid to the development of vaccines against alphaviruses themselves. Recent progress in alphavirus vector development and vaccine technology has allowed conducting clinical trials in humans.

  19. Scintillator based beta batteries

    Science.gov (United States)

    Rensing, Noa M.; Tiernan, Timothy C.; Shirwadkar, Urmila; O'Dougherty, Patrick; Freed, Sara; Hawrami, Rastgo; Squillante, Michael R.

    2013-05-01

    Some long-term, remote applications do not have access to conventional harvestable energy in the form of solar radiation (or other ambient light), wind, environmental vibration, or wave motion. Radiation Monitoring Devices, Inc. (RMD) is carrying out research to address the most challenging applications that need power for many months or years and which have undependable or no access to environmental energy. Radioisotopes are an attractive candidate for this energy source, as they can offer a very high energy density combined with a long lifetime. Both large scale nuclear power plants and radiothermal generators are based on converting nuclear energy to heat, but do not scale well to small sizes. Furthermore, thermo-mechanical power plants depend on moving parts, and RTG's suffer from low efficiency. To address the need for compact nuclear power devices, RMD is developing a novel beta battery, in which the beta emissions from a radioisotope are converted to visible light in a scintillator and then the visible light is converted to electrical power in a photodiode. By incorporating 90Sr into the scintillator SrI2 and coupling the material to a wavelength-matched solar cell, we will create a scalable, compact power source capable of supplying milliwatts to several watts of power over a period of up to 30 years. We will present the latest results of radiation damage studies and materials processing development efforts, and discuss how these factors interact to set the operating life and energy density of the device.

  20. RF Based Spy

    Directory of Open Access Journals (Sweden)

    Robot Prerna Jain

    2014-04-01

    Full Text Available The intention of this paper is to reduce human victims in terrorist attack such as 26/11. So this problem can be overcome by designing the RF based spy robot which involves wireless camera. so that from this we can examine rivals when it required. This robot can quietly enter into enemy area and sends us the information via wireless camera. On the other hand one more feature is added in this robot that is colour sensor. Colour sensor senses the colour of surface and according to that robot will change its colour. Because of this feature this robot can’t easily detected by enemies. The movement of this robot is wirelessly controlled by a hand held RF transmitter to send commands to the RF receiver mounted on the moving robot. Since human life is always Valueable, these robots are the substitution of soldiers in war areas. This spy robot can also be used in star hotels, shopping malls, jewelry show rooms, etc where there can be threat from intruders or terrorists.

  1. Explanation-Based Auditing

    CERN Document Server

    Fabbri, Daniel

    2011-01-01

    To comply with emerging privacy laws and regulations, it has become common for applications like electronic health records systems (EHRs) to collect access logs, which record each time a user (e.g., a hospital employee) accesses a piece of sensitive data (e.g., a patient record). Using the access log, it is easy to answer simple queries (e.g., Who accessed Alice's medical record?), but this often does not provide enough information. In addition to learning who accessed their medical records, patients will likely want to understand why each access occurred. In this paper, we introduce the problem of generating explanations for individual records in an access log. The problem is motivated by user-centric auditing applications, and it also provides a novel approach to misuse detection. We develop a framework for modeling explanations which is based on a fundamental observation: For certain classes of databases, including EHRs, the reason for most data accesses can be inferred from data stored elsewhere in the da...

  2. Geovisualization based upon KML

    Directory of Open Access Journals (Sweden)

    Marianna Zichar

    2012-06-01

    Full Text Available The extension kml refers to a human readable file format that is based on a markup language deriving from XML and became rather popular mainly due to Google Earth. This type of files uses not only the classical geometric data, but coordinates of longitude and latitude (in case of 3D system also coordinate of altitude to visualize the different geographically referenced objects, phenomena and processes. Nowadays more than 10 millions of kml files can be accessed via the internet, and this number is still increasing. However, knowledge of the standard features of kml is not always sufficient, because the circumstances of its application influence its usage. The functionality of the APIs for the web-embeddable Google Maps and Google Earth programs is determinative concerning this issue. The elements of the standard KML cannot be always used without any change, but the clever usage of the API can result effective tools of dynamism. My aim is to review how wide the range of kml files application is, to describe their differences and to share some personal experiences.

  3. ‘"Education-based Research"

    DEFF Research Database (Denmark)

    Degn Johansson, Troels

    This paper lays out a concept of education-based research-the production of research knowledge within the framework of tertiary design education-as an integration of problem-based learning and research-based education. This leads to a critique of reflective practice as the primary way to facilitate...... learning at this level, a discussion of the nature of design problems in the instrumentalist tradition, and some suggestions as to how design studies curricula may facilitate education-based research....

  4. Organizational Semantic Web based Portals

    OpenAIRE

    necula, sabina-cristiana

    2011-01-01

    This paper tries to treat organizational semantic web based portals. The first part of the paper focuses on concepts regarding semantic web based portals. After discussing some concepts we treat the basic functionalities that a semantic web based portal must have and we finish by presenting these functionalities by actual examples. We present semantic web based portals after studying the necessary implementations from literature and practice. We develop some examples that use semantic web bas...

  5. The Activity-Based Approach

    OpenAIRE

    McNally, Michael G.; Rindt, Craig

    2008-01-01

    What is the activity-based approach (ABA) and how does it differ from the conventional trip-based model of travel behavior? From where has the activity approach evolved, what is its current status, and what are its potential applications in transportation forecasting and policy analysis. What have been the contributions of activity-based approaches to understanding travel behavior? The conventional trip-based model of travel demand forecasting (see Chapters 2 and 3) has always lacked...

  6. Securing web-based exams

    NARCIS (Netherlands)

    Sessink, O.D.T.; Beeftink, H.H.; Tramper, J.; Hartog, R.J.M.

    2004-01-01

    Learning management systems may offer web-based exam facilities. Such facilities entail a higher risk to exams fraud than traditional paper-based exams. The article discusses security issues with web-based exams, and proposes precautionary measures to reduce the risks. A security model is presented

  7. PMIS: Data Base Design Report

    Science.gov (United States)

    Fiddleman, Richard; Gorman, Michael M.

    1972-01-01

    PMIS is a computer-based planning and management information system for local school districts. This report centers on the PMIS data bases that contain school system data by reviewing the major phases involved in their creation, explaining the factors that caused the unique orientation of the data bases, reviewing the two tasks that comprise the…

  8. Image Data Bases on Campus.

    Science.gov (United States)

    Kaplan, Reid; Mathieson, Gordon

    1989-01-01

    A description of how image database technology was used to develop two prototypes for academic and administrative applications at Yale University, one using a video data base integration and the other using document-scanning data base technology, is presented. Technical underpinnings for the creation of data bases are described. (Author/MLW)

  9. Lunar Base Heat Pump

    Science.gov (United States)

    Walker, D.; Fischbach, D.; Tetreault, R.

    1996-01-01

    The objective of this project was to investigate the feasibility of constructing a heat pump suitable for use as a heat rejection device in applications such as a lunar base. In this situation, direct heat rejection through the use of radiators is not possible at a temperature suitable for lde support systems. Initial analysis of a heat pump of this type called for a temperature lift of approximately 378 deg. K, which is considerably higher than is commonly called for in HVAC and refrigeration applications where heat pumps are most often employed. Also because of the variation of the rejection temperature (from 100 to 381 deg. K), extreme flexibility in the configuration and operation of the heat pump is required. A three-stage compression cycle using a refrigerant such as CFC-11 or HCFC-123 was formulated with operation possible with one, two or three stages of compression. Also, to meet the redundancy requirements, compression was divided up over multiple compressors in each stage. A control scheme was devised that allowed these multiple compressors to be operated as required so that the heat pump could perform with variable heat loads and rejection conditions. A prototype heat pump was designed and constructed to investigate the key elements of the high-lift heat pump concept. Control software was written and implemented in the prototype to allow fully automatic operation. The heat pump was capable of operation over a wide range of rejection temperatures and cooling loads, while maintaining cooling water temperature well within the required specification of 40 deg. C +/- 1.7 deg. C. This performance was verified through testing.

  10. Telemetry-Based Ranging

    Science.gov (United States)

    Hamkins, Jon; Vilnrotter, Victor A.; Andrews, Kenneth S.; Shambayati, Shervin

    2011-01-01

    A telemetry-based ranging scheme was developed in which the downlink ranging signal is eliminated, and the range is computed directly from the downlink telemetry signal. This is the first Deep Space Network (DSN) ranging technology that does not require the spacecraft to transmit a separate ranging signal. By contrast, the evolutionary ranging techniques used over the years by NASA missions, including sequential ranging (transmission of a sequence of sinusoids) and PN-ranging (transmission of a pseudo-noise sequence) whether regenerative (spacecraft acquires, then regenerates and retransmits a noise-free ranging signal) or transparent (spacecraft feeds the noisy demodulated uplink ranging signal into the downlink phase modulator) relied on spacecraft power and bandwidth to transmit an explicit ranging signal. The state of the art in ranging is described in an emerging CCSDS (Consultative Committee for Space Data Systems) standard, in which a pseudo-noise (PN) sequence is transmitted from the ground to the spacecraft, acquired onboard, and the PN sequence is coherently retransmitted back to the ground, where a delay measurement is made between the uplink and downlink signals. In this work, the telemetry signal is aligned with the uplink PN code epoch. The ground station computes the delay between the uplink signal transmission and the received downlink telemetry. Such a computation is feasible because symbol synchronizability is already an integral part of the telemetry design. Under existing technology, the telemetry signal cannot be used for ranging because its arrival-time information is not coherent with any Earth reference signal. By introducing this coherence, and performing joint telemetry detection and arrival-time estimation on the ground, a high-rate telemetry signal can provide all the precision necessary for spacecraft ranging.

  11. Space-based detectors

    Science.gov (United States)

    Sesana, A.; Weber, W. J.; Killow, C. J.; Perreur-Lloyd, M.; Robertson, D. I.; Ward, H.; Fitzsimons, E. D.; Bryant, J.; Cruise, A. M.; Dixon, G.; Hoyland, D.; Smith, D.; Bogenstahl, J.; McNamara, P. W.; Gerndt, R.; Flatscher, R.; Hechenblaikner, G.; Hewitson, M.; Gerberding, O.; Barke, S.; Brause, N.; Bykov, I.; Danzmann, K.; Enggaard, A.; Gianolio, A.; Vendt Hansen, T.; Heinzel, G.; Hornstrup, A.; Jennrich, O.; Kullmann, J.; Møller-Pedersen, S.; Rasmussen, T.; Reiche, J.; Sodnik, Z.; Suess, M.; Armano, M.; Sumner, T.; Bender, P. L.; Akutsu, T.; Sathyaprakash, B. S.

    2014-12-01

    The parallel session C5 on Space-Based Detectors gave a broad overview over the planned space missions related to gravitational wave detection. Overviews of the revolutionary science to be expected from LISA was given by Alberto Sesana and Sasha Buchman. The launch of LISA Pathfinder (LPF) is planned for 2015. This mission and its payload "LISA Technology Package" will demonstrate key technologies for LISA. In this context, reference masses in free fall for LISA, and gravitational physics in general, was described by William Weber, laser interferometry at the pico-metre level and the optical bench of LPF was presented by Christian Killow and the performance of the LPF optical metrology system by Paul McNamara. While LPF will not yet be sensitive to gravitational waves, it may nevertheless be used to explore fundamental physics questions, which was discussed by Michele Armano. Some parts of the LISA technology that are not going to be demonstrated by LPF, but under intensive development at the moment, were presented by Oliver Jennrich and Oliver Gerberding. Looking into the future, Japan is studying the design of a mid-frequency detector called DECIGO, which was discussed by Tomotada Akutsu. Using atom interferometry for gravitational wave detection has also been recently proposed, and it was critically reviewed by Peter Bender. In the nearer future, the launch of GRACE Follow-On (for Earth gravity observation) is scheduled for 2017, and it will include a Laser Ranging Interferometer as technology demonstrator. This will be the first inter-spacecraft laser interferometer and has many aspects in common with the LISA long arm, as discussed by Andrew Sutton.

  12. Soy-based renoprotection.

    Science.gov (United States)

    McGraw, Nancy J; Krul, Elaine S; Grunz-Borgmann, Elizabeth; Parrish, Alan R

    2016-05-01

    Chronic kidney disease (CKD) is a significant public health problem as risk factors such as advanced age, obesity, hypertension and diabetes rise in the global population. Currently there are no effective pharmacologic treatments for this disease. The role of diet is important for slowing the progression of CKD and managing symptoms in later stages of renal insufficiency. While low protein diets are generally recommended, maintaining adequate levels of intake is critical for health. There is an increasing appreciation that the source of protein may also be important. Soybean protein has been the most extensively studied plant-based protein in subjects with kidney disease and has demonstrated renal protective properties in a number of clinical studies. Soy protein consumption has been shown to slow the decline in estimated glomerular filtration rate and significantly improve proteinuria in diabetic and non-diabetic patients with nephropathy. Soy's beneficial effects on renal function may also result from its impact on certain physiological risk factors for CKD such as dyslipidemia, hypertension and hyperglycemia. Soy intake is also associated with improvements in antioxidant status and systemic inflammation in early and late stage CKD patients. Studies conducted in animal models have helped to identify the underlying molecular mechanisms that may play a role in the positive effects of soy protein on renal parameters in polycystic kidney disease, metabolically-induced kidney dysfunction and age-associated progressive nephropathy. Despite the established relationship between soy and renoprotection, further studies are needed for a clear understanding of the role of the cellular and molecular target(s) of soy protein in maintaining renal function. PMID:27152261

  13. Nanoparticle-based Sensors

    Directory of Open Access Journals (Sweden)

    V.K. Khanna

    2008-09-01

    Full Text Available Nanoparticles exhibit several unique properties that can be applied to develop chemical and biosensorspossessing desirable features like enhanced sensitivity and lower detection limits. Gold nanoparticles arecoated with sugars tailored to recognise different biological substances. When mixed with a weak solution ofthe sugar-coated nanoparticles, the target substance, e.g., ricin or E.coli, attaches to the sugar, thereby alteringits properties and changing the colour. Spores of bacterium labeled with carbon dots have been found to glowupon illumination when viewed with a confocal microscope. Enzyme/nanoparticle-based optical sensors forthe detection of organophosphate (OP compounds employ nanoparticle-modified fluorescence of an inhibitorof the enzyme to generate the signal for the OP compound detection. Nanoparticles shaped as nanoprisms,built of silver atoms, appear red on exposure to light. These nanoparticles are used as diagnostic labels thatglow when target DNA, e.g., those of anthrax or HIV, are present. Of great importance are tools like goldnanoparticle-enhanced surface-plasmon resonance sensor and silver nanoparticle surface-enhanced portableRaman integrated tunable sensor. Nanoparticle metal oxide chemiresistors using micro electro mechanical systemhotplate are very promising devices for toxic gas sensing. Chemiresistors comprising thin films of nanogoldparticles, encapsulated in monomolecular layers of functionalised alkanethiols, deposited on interdigitatedmicroelectrodes, show resistance changes through reversible absorption of vapours of harmful gases. Thispaper reviews the state-of-the-art sensors for chemical and biological terror agents, indicates their capabilitiesand applications, and presents the future scope of these devices.Defence Science Journal, 2008, 58(5, pp.608-616, DOI:http://dx.doi.org/10.14429/dsj.58.1683

  14. Barrier Data Base user's guide

    International Nuclear Information System (INIS)

    A special purpose data base for physical security barriers has been developed. In addition to barriers, the entities accommodated by the Barrier Data Base (BDB) include threats and references. A threat is established as a configuration of people and equipment which has been employed to penetrate (or attempt to penetrate) a barrier. References are used to cite publications pertinent to the barriers and threats in the data base. Utilization and maintenance of the Barrier Data Base is achieved with LIST, QUERY, ENTER, DELETE, and CHANGE commands which are used to manipulate the data base entities

  15. From oil-based mud to water-based mud

    International Nuclear Information System (INIS)

    Maersk Olie og Gas AS has used low toxic oil-based muds extensively since 1982 for drilling development wells and later in the development of horizontal well drilling techniques. However, in view of the strong drive towards a reduction in the amount of oil discharged to the North Sea from the oil industry, Maersk Olie og Gas AS initiated trials with new or improved types of water-based mud, first in deviated wells (1989) and then in horizontal wells (1990). The paper reviews Maersk Olie og Gas As experience with oil-based mud since the drilling of the first horizontal well in 1987, specifically with respect to cuttings washing equipment, oil retention on cuttings, and the procedure for monitoring of this parameter. It describes the circumstances leading to the decision to revert to water-based mud systems. Finally, it reviews the experience gained so far with the new improved types of water-based mud systems, mainly glycol and KCl/polymer mud systems. Comparison of operational data, such as rate of penetration, torque and drag, etc., is made between wells drilled with oil-based mud and water-based mud. The trials with the new improved types of water-based mud systems have been positive, i.e. horizontal wells can be drilled successfully with water-based mud. As a result, Maersk Olie og and Gas AS has decided to discontinue the use of low toxic oil-based muds in the Danish sector of the North Sea

  16. Research on coal staged conversion poly-generation system based on fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Mingjiang Ni; Chao Li; Mengxiang Fang; Qinhui Wang; Zhongyang Luo; Kefa Cen

    2014-01-01

    A new coal staged conversion poly-generation system combined coal combustion and pyrolysis has been developed for clean and high efficient utilization of coal. Coal is the first pyrolysed in a fluidized pyrolyzer. The pyrolysis gas is then purified and used for chemical product or liquid fuel production. Tar is collected during purification and can be processed to extract high value product and to make liquid fuels by hydro-refining. Semi-coke from the pyrolysis reactor is burned in a circulating fluidized bed (CFB) combustor for heat or power generation. The system can realize coal multi-product generation and has a great potential to increase coal utilization value. A 1 MW poly-generation system pilot plant and a 12 MW CFB gas, tar, heat and power poly-generation system was erected. The experimental study focused on the two fluidized bed operation and characterization of gas, tar and char yields and compositions. The results showed that the system could operate stable, and produce about 0.12 m3/kg gas with 22 MJ/m3 heating value and about 10 wt%tar when using Huainan bituminous coal under pyrolysis temperature between 500 and 600 ?C. The produced gases were mainly H2, CH4, CO, CO2, C2H4, C2H6, C3H6 and C3H8. The CFB combustor can burn semi-coke steadily. The application prospect of the new system was discussed.

  17. Potential for Coal-to-Liquids Conversion in the U.S.-Resource Base

    International Nuclear Information System (INIS)

    By applying the multi-Hubbert curve analysis to coal production in the United States, we demonstrate that anthracite production can be modeled with a single Hubbert curve that extends to the practical end of commercial production of this highest-rank coal. The production of bituminous coal from existing mines is about 80% complete and can be carried out at the current rate for the next 20 years. The production of subbituminous coal from existing mines can be carried out at the current rate for 40-45 years. Significant new investment to extend the existing mines and build new ones would have to commence in 2009 to sustain the current rate of coal production, 1 billion tons per year, in 2029. In view of the existing data, we conclude that there is no spare coal production capacity of the size required for massive coal conversion to liquid transportation fuels. Our analysis is independent of other factors that will prevent large-scale coal liquefaction projects: the inefficiency of the process and either emissions of greenhouse gases or energy cost of sequestration

  18. Workplace Based Assessment in Psychiatry

    Directory of Open Access Journals (Sweden)

    Ayse Devrim Basterzi

    2009-11-01

    Full Text Available Workplace based assessment refers to the assessment of working practices based on what doctors actually do in the workplace, and is predominantly carried out in the workplace itself. Assessment drives learning and it is therefore essential that workplace-based assessment focuses on important attributes rather than what is easiest to assess. Workplacebased assessment is usually competency based. Workplace based assesments may well facilitate and enhance various aspects of educational supervisions, including its structure, frequency and duration etc. The structure and content of workplace based assesments should be monitored to ensure that its benefits are maximised by remaining tailored to individual trainees' needs. Workplace based assesment should be used for formative and summative assessments. Several formative assessment methods have been developed for use in the workplace such as mini clinical evaluation exercise (mini-cex, evidence based journal club assesment and case based discussion, multi source feedback etc. This review discusses the need of workplace based assesments in psychiatry graduate education and introduces some of the work place based assesment methods.

  19. Measurement-based quantum communication

    Science.gov (United States)

    Zwerger, M.; Briegel, H. J.; Dür, W.

    2016-03-01

    We review and discuss the potential of using measurement-based elements in quantum communication schemes, where certain tasks are realized with the help of entangled resource states that are processed by measurements. We consider long-range quantum communication based on the transmission of encoded quantum states, where encoding, decoding and syndrome readout are implemented using small-scale resource states. We also discuss entanglement-based schemes and consider measurement-based quantum repeaters. An important element in these schemes is entanglement purification, which can also be implemented in a measurement-based way. We analyze the influence of noise and imperfections in these schemes and show that measurement-based implementation allows for very large error thresholds of the order of 10 % noise per qubit and more. We show how to obtain optimal resource states for different tasks and discuss first experimental realizations of measurement-based quantum error correction using trapped ions and photons.

  20. Case-based reasoning: The marriage of knowledge base and data base

    Science.gov (United States)

    Pulaski, Kirt; Casadaban, Cyprian

    1988-01-01

    The coupling of data and knowledge has a synergistic effect when building an intelligent data base. The goal is to integrate the data and knowledge almost to the point of indistinguishability, permitting them to be used interchangeably. Examples given in this paper suggest that Case-Based Reasoning is a more integrated way to link data and knowledge than pure rule-based reasoning.

  1. Evidence-based dentistry.

    Science.gov (United States)

    Chambers, David W

    2010-01-01

    Both panegyric and criticism of evidence-based dentistry tend to be clumsy because the concept is poorly defined. This analysis identifies several contributions to the profession that have been made under the EBD banner. Although the concept of clinicians integrating clinical epidemiology, the wisdom of their practices, and patients' values is powerful, its implementation has been distorted by a too heavy emphasis of computerized searches for research findings that meet the standards of academics. Although EBD advocates enjoy sharing anecdotal accounts of mistakes others have made, faulting others is not proof that one's own position is correct. There is no systematic, high-quality evidence that EBD is effective. The metaphor of a three-legged stool (evidence, experience, values, and integration) is used as an organizing principle. "Best evidence" has become a preoccupation among EBD enthusiasts. That overlong but thinly developed leg of the stool is critiqued from the perspectives of the criteria for evidence, the difference between internal and external validity, the relationship between evidence and decision making, the ambiguous meaning of "best," and the role of reasonable doubt. The strongest leg of the stool is clinical experience. Although bias exists in all observations (including searches for evidence), there are simple procedures that can be employed in practice to increase useful and objective evidence there, and there are dangers in delegating policy regarding allowable treatments to external groups. Patient and practitioner values are the shortest leg of the stool. As they are so little recognized, their integration in EBD is problematic and ethical tensions exist where paternalism privileges science over patient's self-determined best interests. Four potential approaches to integration are suggested, recognizing that there is virtually no literature on how the "seat" of the three-legged stool works or should work. It is likely that most dentists

  2. Optimal pricing decision model based on activity-based costing

    Institute of Scientific and Technical Information of China (English)

    王福胜; 常庆芳

    2003-01-01

    In order to find out the applicability of the optimal pricing decision model based on conventional costbehavior model after activity-based costing has given strong shock to the conventional cost behavior model andits assumptions, detailed analyses have been made using the activity-based cost behavior and cost-volume-profitanalysis model, and it is concluded from these analyses that the theory behind the construction of optimal pri-cing decision model is still tenable under activity-based costing, but the conventional optimal pricing decisionmodel must be modified as appropriate to the activity-based costing based cost behavior model and cost-volume-profit analysis model, and an optimal pricing decision model is really a product pricing decision model construc-ted by following the economic principle of maximizing profit.

  3. Knowledge base verification based on enhanced colored petri net

    International Nuclear Information System (INIS)

    Verification is a process aimed at demonstrating whether a system meets it's specified requirements. As expert systems are used in various applications, the knowledge base verification of systems takes an importatn position. The conventional Petri net approach that has been studied recently in order to verify the knowledge base is found that it is inadequate to verify the knowledge base of large and complex system, such as alarm processing system of nuclear power plant. Thus, we propose an improved method that models the knowledge base as enhanced colored Petri net. In this study, we analyze the reachability and the error characteristics of the knowledge base and apply the method to verification of simple knowledge base

  4. Knowledge base verification based on enhanced colored petri net

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Hyun; Seong, Poong Hyun [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

    1997-12-31

    Verification is a process aimed at demonstrating whether a system meets it`s specified requirements. As expert systems are used in various applications, the knowledge base verification of systems takes an important position. The conventional Petri net approach that has been studied recently in order to verify the knowledge base is found that it is inadequate to verify the knowledge base of large and complex system, such as alarm processing system of nuclear power plant. Thus, we propose an improved method that models the knowledge base as enhanced colored Petri net. In this study, we analyze the reachability and the error characteristics of the knowledge base and apply the method to verification of simple knowledge base. 8 refs., 4 figs. (Author)

  5. ANALYSIS-BASED SPARSE RECONSTRUCTION WITH SYNTHESIS-BASED SOLVERS

    OpenAIRE

    Cleju, Nicolae; Jafari, Maria,; Plumbley, Mark D.

    2012-01-01

    Analysis based reconstruction has recently been introduced as an alternative to the well-known synthesis sparsity model used in a variety of signal processing areas. In this paper we convert the analysis exact-sparse reconstruction problem to an equivalent synthesis recovery problem with a set of additional constraints. We are therefore able to use existing synthesis-based algorithms for analysis-based exact-sparse recovery. We call this the Analysis-By-Synthesis (ABS) approach. We evaluate o...

  6. XML-Based SHINE Knowledge Base Interchange Language

    Science.gov (United States)

    James, Mark; Mackey, Ryan; Tikidjian, Raffi

    2008-01-01

    The SHINE Knowledge Base Interchange Language software has been designed to more efficiently send new knowledge bases to spacecraft that have been embedded with the Spacecraft Health Inference Engine (SHINE) tool. The intention of the behavioral model is to capture most of the information generally associated with a spacecraft functional model, while specifically addressing the needs of execution within SHINE and Livingstone. As such, it has some constructs that are based on one or the other.

  7. Graph Cuts based Image Segmentation using Fuzzy Rule Based System

    OpenAIRE

    Khokher, M. R.; A. Ghafoor; A.M. Siddiqui

    2012-01-01

    This work deals with the segmentation of gray scale, color and texture images using graph cuts. From input image, a graph is constructed using intensity, color and texture profiles of the image simultaneously. Based on the nature of image, a fuzzy rule based system is designed to find the weight that should be given to a specific image feature during graph development. The graph obtained from the fuzzy rule based weighted average of different image features is further used in normalized graph...

  8. Location-based Modeling and Analysis: Tropos-based Approach

    OpenAIRE

    Ali, Raian; Dalpiaz, Fabiano; Giorgini, Paolo

    2008-01-01

    The continuous growth of interest in mobile applications makes the concept of location essential to design and develop software systems. Location-based software is supposed to be able to monitor the location and choose accordingly the most appropriate behavior. In this paper, we propose a novel conceptual framework to model and analyze location-based software. We mainly focus on the social facets of locations adopting concepts such as social actor, resource, and location-based behavior. Our a...

  9. Acids and bases solvent effects on acid-base strenght

    CERN Document Server

    Cox, Brian G

    2013-01-01

    Acids and bases are ubiquitous in chemistry. Our understanding of them, however, is dominated by their behaviour in water. Transfer to non-aqueous solvents leads to profound changes in acid-base strengths and to the rates and equilibria of many processes: for example, synthetic reactions involving acids, bases and nucleophiles; isolation of pharmaceutical actives through salt formation; formation of zwitter- ions in amino acids; and chromatographic separation of substrates. This book seeks to enhance our understanding of acids and bases by reviewing and analysing their behaviour in non-aqueous solvents. The behaviour is related where possible to that in water, but correlations and contrasts between solvents are also presented.

  10. Remote Monitoring System for Communication Base Based on Short Message

    Directory of Open Access Journals (Sweden)

    Han Yu Fu

    2013-07-01

    Full Text Available This paper presents design and development of an automatic monitoring system of communication base which is an important means to realize modernization of mobile communication base station management. Firstly, this paper proposes the architecture of the monitoring system. The proposed system consists of mocrocontrollers, sensors, GSM module and MFRC500 etc. The value of parameters is measured in the system including terminal is studied and designed, including hardware design based on embedded system and software design. Finally, communication module is discussed. The monitoring system which is designed  based on GSM SMS(short message service can improve the integrity, reliability, flexibility and intellectuality of monitoring system.

  11. Computer-based and web-based radiation safety training

    Energy Technology Data Exchange (ETDEWEB)

    Owen, C., LLNL

    1998-03-01

    The traditional approach to delivering radiation safety training has been to provide a stand-up lecture of the topic, with the possible aid of video, and to repeat the same material periodically. New approaches to meeting training requirements are needed to address the advent of flexible work hours and telecommuting, and to better accommodate individuals learning at their own pace. Computer- based and web-based radiation safety training can provide this alternative. Computer-based and web- based training is an interactive form of learning that the student controls, resulting in enhanced and focused learning at a time most often chosen by the student.

  12. Simultaneous Measurement and Analysis of Noise Levels in Flexible and Rigid Pavements

    OpenAIRE

    Hakan Yıldırım; Selin Açık; Ali Payıdar Akgüngör; Erdem Doğan

    2014-01-01

    Although concrete roads have been used worldwide for years, the same improvement could not exist in Turkey and therefore, bituminous (hot mix) asphalt roads were preferred instead.In this paper, the vastly built HMA (Hot Mix Asphalt) roads and rarely preferred concrete roads were compared based on their level of noise. For this purpose, the concrete road at the length of 2 kilometers between Afyonkarahisar and Emirdag; also the transition point to the HMA road (which continues after the concr...

  13. Emissions and Furnace Gas Temperature for Electricity Generation Via Co-Firing of Coal and Biomass

    OpenAIRE

    Shoaib Mehmood; Bale Reddy; Marc Rosen

    2015-01-01

    The emissions of carbon dioxide and nitrogen and sulphur oxides for electricity generation with coal and biomass co-firing are investigated and the furnace gas temperature assessed. The study uses simulation and considers fuel combinations based on two coals (bituminous coal, lignite) and four types of biomass (rice husk, sawdust, chicken litter, refused derived fuel). With increasing biomass, net CO2 emissions are seen to decline significantly for all types of selected biomass, while gross c...

  14. Modeling of asphalt by means of discrete element method – an initial study

    OpenAIRE

    Feng, Huan; Hededal, Ole; Stang, Henrik

    2013-01-01

    Asphalt is a viscous material consisting of a matrix of stones, sand and filler glued together by a bituminous binder, which is used in many pavement constructions. Knowledge about asphalt is mainly based on the results of experimental and empirical investigation, which comes at the expense of conducting time-consuming and lab-costly procedures. The use of numerical models, capable of reducing greatly the testing cost, has shown great potential in characterizing asphalt-aggregate mixtures for...

  15. The Influence Of Mass Fraction Of Dressed Coal On Ignition Conditions Of Composite Liquid Fuel Droplet

    OpenAIRE

    Shlegel Nikita E.; Kats Mark D.; Glushkov Dmitriy O.

    2015-01-01

    The laws of condition modification of inert heat and ignition in an oxidant flow of composite liquid fuel droplet were studied by the developed experimental setup. Investigations were for composite liquid fuel composition based on the waste of bituminous and nonbaking coal processing, appropriate carbon dust, water, used motor oil. The characteristics of boundary layer inertia heat of composite liquid fuel droplet, thermal decomposition of coal organic part, the yield of volatiles and evapora...

  16. Characterization of Some Nigerian Coals for Power Generation

    OpenAIRE

    Chukwu, M.; Folayan, C. O.; Pam, G. Y.; D.O. Obada

    2016-01-01

    Five coal samples from Odagbo (Kogi State), Owukpa (Benue State), Ezimo (Enugu State), Amansiodo (Enugu State), and Inyi (Enugu State) of Nigerian coal deposits were subjected to proximate analysis, ultimate analysis, calorific value determination, and petrographic and thermogravimetric analysis to determine their suitability for power generation. Based on results of tests carried out, Amansiodo coal is a bituminous, low sulphur, and medium ash coal, while Owukpa coal is a subbituminous A, lo...

  17. Characterization of infiltration capacity of permeable pavements with porous asphalt surface using cantabrian fixed infiltrometer

    OpenAIRE

    Rodríguez Hernández, Jorge; Castro Fresno, Daniel; Fernández Barrera, Andrés Humberto; Vega Zamanillo, Ángel

    2012-01-01

    Porous asphalt is used in Permeable Pavement Systems, but it is sensitive to surface clogging, which leads to a loss in its infiltration capacity. Test methods based on the use of permeable pavement models, which are manufactured in a laboratory and assessed under different clogging conditions, such as slope, rain, and runoff, have been widely applied to the study of permeable pavements with concrete blocks but not to the study of porous bituminous mixtures. The Cantabrian Fixed (CF) Infiltro...

  18. Concurrent array-based queue

    Energy Technology Data Exchange (ETDEWEB)

    Heidelberger, Philip; Steinmacher-Burow, Burkhard

    2015-01-06

    According to one embodiment, a method for implementing an array-based queue in memory of a memory system that includes a controller includes configuring, in the memory, metadata of the array-based queue. The configuring comprises defining, in metadata, an array start location in the memory for the array-based queue, defining, in the metadata, an array size for the array-based queue, defining, in the metadata, a queue top for the array-based queue and defining, in the metadata, a queue bottom for the array-based queue. The method also includes the controller serving a request for an operation on the queue, the request providing the location in the memory of the metadata of the queue.

  19. Fast Density Based Clustering Algorithm

    OpenAIRE

    Priyanka Trikha; Singh Vijendra

    2013-01-01

    Clustering problem is an unsupervised learning problem. It is a procedure that partition data objects into matching clusters. The data objects in the same cluster are quite similar to each other and dissimilar in the other clusters. The traditional algorithms do not meet the latest multiple requirements simultaneously for objects. Density-based clustering algorithms find clusters based on density of data points in a region. DBSCAN algorithm is one of the density-based clustering algorithms. I...

  20. Restructuring and simplifying rule bases

    OpenAIRE

    Vanthienen, Jan; Dries, E; WETS, G

    1995-01-01

    Rule bases are commonly acquired, by expert and/or knowledge engineer, in a form which is well suited for acquisition purposes. When the knowledge base is executed, however, a different structure may be required. Moreover, since human experts normally do not provide the knowledge in compact chunks, rule bases often suffer from redundancy. This may considerably harm efficiency. In this paper a procedure is examined to transform rules that are specified in the knowledge acquisition process ...

  1. Principles of models based engineering

    Energy Technology Data Exchange (ETDEWEB)

    Dolin, R.M.; Hefele, J.

    1996-11-01

    This report describes a Models Based Engineering (MBE) philosophy and implementation strategy that has been developed at Los Alamos National Laboratory`s Center for Advanced Engineering Technology. A major theme in this discussion is that models based engineering is an information management technology enabling the development of information driven engineering. Unlike other information management technologies, models based engineering encompasses the breadth of engineering information, from design intent through product definition to consumer application.

  2. Risk-based configuration management

    International Nuclear Information System (INIS)

    Risk-based configuration management is an important research area of using PSA technology to evaluate and improve the Technical Specification Requirements of nuclear power plant. Some aspects on risk-based configuration management are discussed, including evaluation methods, risk acceptance criteria and essential elements which should be paid attention to during the management process. And results of the case study based on a real nuclear power plant are presented

  3. dBASE IV basics

    Energy Technology Data Exchange (ETDEWEB)

    O`Connor, P.

    1994-09-01

    This is a user`s manual for dBASE IV. dBASE IV is a popular software application that can be used on your personal computer to help organize and maintain your database files. It is actually a set of tools with which you can create, organize, select and manipulate data in a simple yet effective manner. dBASE IV offers three methods of working with the product: (1) control center: (2) command line; and (3) programming.

  4. Instantaneous noise-based logic

    OpenAIRE

    Kish, Laszlo B.; Khatri, Sunil; Peper, Ferdinand

    2010-01-01

    We show two universal, Boolean, deterministic logic schemes based on binary noise timefunctions that can be realized without time-averaging units. The first scheme is based on a new bipolar random telegraph wave scheme and the second one makes use of the recent noise-based logic which is conjectured to be the brain's method of logic operations [Physics Letters A 373 (2009) 2338-2342]. Error propagation and error removal issues are also addressed.

  5. Feature-Based Attention and Feature-Based Expectation.

    Science.gov (United States)

    Summerfield, Christopher; Egner, Tobias

    2016-06-01

    Foreknowledge of target stimulus features improves visual search performance as a result of 'feature-based attention' (FBA). Recent studies have reported that 'feature-based expectation' (FBE) also heightens decision sensitivity. Superficially, it appears that the latter work has simply rediscovered (and relabeled) the effects of FBA. However, this is not the case. Here we explain why. PMID:27079632

  6. Trace-Based Code Generation for Model-Based Testing

    NARCIS (Netherlands)

    Kanstrén, T.; Piel, E.; Gross, H.-G.

    2009-01-01

    Paper Submitted for review at the Eighth International Conference on Generative Programming and Component Engineering. Model-based testing can be a powerful means to generate test cases for the system under test. However, creating a useful model for model-based testing requires expertise in the (fo

  7. Managing the Gap between Curriculum Based and Problem Based Learning

    DEFF Research Database (Denmark)

    Bygholm, Ann; Buus, Lillian

    2009-01-01

    /or but rather both/and. In this paper we describe an approach to design and delivery of online courses in computer science which on the one hand is based on a specified curriculum and on the other hand gives room for different learning strategies, problem based learning being one of them. We discuss...

  8. Isochronous cyclotron data base description

    International Nuclear Information System (INIS)

    The relational data base of the control parameters of the isochronous cyclotron, Isochronous Cyclotron Data Base (ICDB), is described. The relational data base under consideration, written in Transact SQL for the MS SQL Server 2000 with the use of MS Enterprise Manager and MS Query Analyzer, was installed on the server of the AIC144 isochronous cyclotron in Krakow, which operates under the control of the operating system MS Windows Server 2003 (Standard Edition). The interface of the data base under considerations is written in C++ with the use of Visual C++ .NET and is built in the Cyclotron Operator Help Program (COHP), which is used for modeling the operational modes of the isochronous cyclotron. Communication between the COHP and the relational data base is realised on the base of the Open Data Base Connectivity protocol. The relational data base of the control parameter of the isochronous cyclotron is intended: firstly, for systematization and automatic use of all measured and modelled magnetic field maps in the process of modeling the operational modes; secondly, for systematization and convenient access to the stored operational modes; thirdly, for simplifying the operator's work. The relational data base of the control parameter of the isochronous cyclotron reflects its physical structure and the logic of its operator's work. (author)

  9. Distributed event-based systems

    CERN Document Server

    Fiege, Ludger; Pietzuch, Peter R

    2006-01-01

    This book provides an in-depth description of event-based systems, covering topics ranging from local event matching and distributed event forwarding algorithms, through a practical discussion of software engineering issues raised by the event-based style, to state-of-the-art research in event-based systems like composite event detection and security. The authors offer a comprehensive overview, and show the power of event-based architectures in modern system design, encouraging professionals to exploit this technique in next generation large-scale distributed applications like information diss

  10. Web-based support systems

    CERN Document Server

    Yao, JingTao

    2010-01-01

    The emerging interdisciplinary study of Web-based support systems focuses on the theories, technologies and tools for the design and implementation of Web-based systems that support various human activities. This book presents the state-of-the-art in Web-based support systems (WSS). The research on WSS is multidisciplinary and focuses on supporting various human activities in different domains/fields based on computer science, information technology, and Web technology. The main goal is to take the opportunities of the Web, to meet the challenges of the Web, to extend the human physical limita

  11. Capability-based computer systems

    CERN Document Server

    Levy, Henry M

    2014-01-01

    Capability-Based Computer Systems focuses on computer programs and their capabilities. The text first elaborates capability- and object-based system concepts, including capability-based systems, object-based approach, and summary. The book then describes early descriptor architectures and explains the Burroughs B5000, Rice University Computer, and Basic Language Machine. The text also focuses on early capability architectures. Dennis and Van Horn's Supervisor; CAL-TSS System; MIT PDP-1 Timesharing System; and Chicago Magic Number Machine are discussed. The book then describes Plessey System 25

  12. Polyurethane Based Inhibition for High Flame Temperature Nitramine Based Composite Modified Double Base propellant

    OpenAIRE

    S. D. Kakade; M. V. Vaidya; D. G. Khangaonkar; P. K. Divekar; U. B. Kadam; S. N. Asthana

    1998-01-01

    The findings for polypropylene glycol (PPG) and hydroxyl-terminated polybutadiene (HTPB)-based inhibition systems are reported. These findings established that the inhibition system comprising HTPB-IPDI-IDP binder and Sb/sub 2/O/sub 3/-C black filler is most suitable for advanced nitramine-based composite modified double-base propellants in terms of mechanical properties and processibility. The promising composition was characterised for glass-transition behaviour and propellant-inhibi...

  13. Emissions and Furnace Gas Temperature for Electricity Generation Via Co-Firing of Coal and Biomass

    Directory of Open Access Journals (Sweden)

    Shoaib Mehmood

    2015-12-01

    Full Text Available The emissions of carbon dioxide and nitrogen and sulphur oxides for electricity generation with coal and biomass co-firing are investigated and the furnace gas temperature assessed. The study uses simulation and considers fuel combinations based on two coals (bituminous coal, lignite and four types of biomass (rice husk, sawdust, chicken litter, refused derived fuel. With increasing biomass, net CO2 emissions are seen to decline significantly for all types of selected biomass, while gross carbon dioxide emissions increase for all blends except bituminous coal/refuse derived fuel, lignite/chicken litter and lignite/refuse derived fuel. The reductions in emissions of nitrogen and sulphur oxides are dependent on the contents of nitrogen and sulphur in the biomass. The results also show for all fuel combinations that increasing the biomass proportion decreases the furnace exit gas temperature.

  14. Comprehensive standards: the power generation case

    International Nuclear Information System (INIS)

    This study presents an illustrative data base of material quantities and environmental effluents in the fuel cycles for alternative technologies of thermally generated power. The entire fuel cycle for each of the alternative ten technologies is outlined for a representative power plant generating 1000 Mw of electrical power. The required utilization of material resources and the fuel-cycle material quantities are indicated on a flow sheet for each technology. The technologies considered are: (1) Light Water Nuclear Reactor; (2)Coal: Appalachian Bituminous and Northwestern Sub-bituminous; (3) Residual fuel oil; (4) Natural Gas; (5) High Sulfur Coal, with Coal Gasification and Sulfur Removal; (6) High Sulfur Coal, with SO2 recovery by Wet-Limestone Scrubbing; (7) Geothermal Steam; (8) Breeder Fission Reactor; (9) Solar Energy; and (10) Thermonuclear Fusion

  15. Detection of reactive free radicals in fresh coal mine dust and their implication for pulmonary injury.

    Science.gov (United States)

    Dalal, N S; Suryan, M M; Vallyathan, V; Green, F H; Jafari, B; Wheeler, R

    1989-01-01

    Freshly ground and aged anthracite and bituminous coal samples were investigated by electron spin resonance (ESR) spectroscopy to detect the presence, concentration and reactivity of free radicals. Freshly ground anthracite coal produced greater concentration of free radicals than the bituminous coal, and the radical reactivity was also greater for the anthracite. The reactivity of the newly produced free radicals in the anthracite dust correlated with the dust's toxicity. Furthermore, similar coal-based free radicals were detected in the lung tissue of autopsied coal miners, suggestive of persistent reactivity by the embedded coal dust leading to the progressive disease process. Results of the studies on the severity of coal workers' pneumoconiosis (CWP) and free radical concentration in lung tissue support this hypothesis. PMID:2705696

  16. Economy, environmental issues and market requirements. The example of coal mining

    International Nuclear Information System (INIS)

    Domestic coal mining is in a recession stage now. The cost of mining increases and the European market is saturated. The projection of the needs for solid fuels till 2000 was analyzed based on an investigation made among 80 large-scale customers and in the municipal and household sphere. Demands for bituminous coal for power plants exhibit an increasing trend. From the environmental point of view it is unfavourable that, as the district authorities suppose, brown coal and bituminous coal sludges will continue to be used by the households and communities after 2000. The problem of the mining and processing costs and of the related coal prices is a crucial issue in the future development of fuel mining in the Czech Republic. (M.D.). 3 refs

  17. Wavelength conversion based spectral imaging

    DEFF Research Database (Denmark)

    Dam, Jeppe Seidelin

    resolution for this spectral region. Today, an increasing number of applications exists outside the spectral region covered by Si-based devices, e.g. within cleantech, medical or food imaging. We present a technology based on wavelength conversion which will extend the spectral coverage of state of the art...

  18. Interpretation-Based Grammar Teaching.

    Science.gov (United States)

    Ellis, Rod

    1993-01-01

    In contrast to the usual approach to teaching grammar, this article argues for a comprehension-based approach. Based on a model of second-language acquisition, it examines a number of possible goals for grammar instruction (e.g., to promote "intake" of new grammatical features by helping learners notice input features and comprehend the meaning).…

  19. Methods in Logic Based Control

    DEFF Research Database (Denmark)

    Christensen, Georg Kronborg

    1999-01-01

    Desing and theory of Logic Based Control systems.Boolean Algebra, Karnaugh Map, Quine McClusky's algorithm. Sequential control design. Logic Based Control Method, Cascade Control Method. Implementation techniques: relay, pneumatic, TTL/CMOS,PAL and PLC- and Soft_PLC implementation. PLC...

  20. The knowledge base of journalism

    DEFF Research Database (Denmark)

    Svith, Flemming

    theories on practice and knowledge. As the result of an abductive reasoning is a theory proposal, there is a need for more deductive approaches to test the validity of this knowledge base claim. It is thus relevant to investigate which rationales are included in the knowledge base of journalism, as the...