Effect of waste polymer addition on the rheology of modified bitumen

Energy Technology Data Exchange (ETDEWEB)

M. Garcia-Morales; P. Partal; F.J. Navarro; C. Gallegos [Universidad de Huelva, Huelva (Spain). Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales

2006-05-15

This paper deals with the modification of petroleum bitumen with four different types of waste polymers. EVA, EVA/LDPE blend, crumb tire rubber and ABS, all of them coming from recycling plants of waste plastic materials, were used as modifying agents of the bitumen employed in the pavement building. Optical microscopy, modulated calorimetry and a set of different rheological tests were developed in order to characterise the modified bitumens. The results obtained reveal that tire rubber as well as its blends with other polymers can be considered as an interesting modifier of the bitumen in a wide range of temperatures. As an elastomer, it endows the pavement a higher flexibility, which makes it more resistant to the traffic loading. The blend composed of EVA and LDPE displays quite promising results at high in-service temperatures, due to the development of a polymer network throughout the modified bitumen. Furthermore, the calorimetry tests carried out demonstrate different degrees of compatibility between the bitumen and the polymers used. 45 refs., 8 figs., 3 tabs.

Cerro Negro bitumen degradation by a consortium of marine benthic microorganisms

Energy Technology Data Exchange (ETDEWEB)

Potter, T.L.; Duval, B. [USDA-ARA, Tifton, GA (USA). Southeast Watershed Research Laboratory

2001-01-01

Cerro Negro bitumen, separated from an Orimulsion sample, was incubated for up to 120 days with sediments collected at a petroleum-impacted site in Tampa Bay, Florida. Biodegradation conditions were optimized by increasing bitumen surface area, continuous agitation on a shaker apparatus, use of a complete growth medium, and maintenance at 37{degree}C. Aerobic degradation conditions were promoted by maintaining sediment contact with the laboratory atmosphere. Bitumen recovered in solvent extracts when compared to autoclaved controls decreased by up to 40% during the first 56 days. There was no detectable change after this. Molasses addition and use of a culture enriched from the sediments did not change the extent or rate of decrease in bitumen recovery. Chemical fractionation of bitumen control and degraded bitumen showed that aromatic and aliphatic fractions were depleted by {approx} 50%. Accumulation of polars was observed; however, the apparent increase was relatively small when compared to the mass loss of the other fractions. Selected biomarker ratios were not affected by incubation indicating their utility for fingerprinting the source bitumen in environmental samples. PAH distribution in the aromatic fraction favored the higher alkyl-homologues with the relative degree of alkylation increasing as the mass of bitumen recovered decreased with degradation. The study showed that up to 40% of the bitumen was bioaccessible and that bioremediation may be a treatment option for sediments contaminated with bitumen by an Orimulsion spill. 36 refs., 8 figs., 5 tabs.

Nitrogen conversion during rapid pyrolysis of coal and petroleum coke in a high-frequency furnace

International Nuclear Information System (INIS)

Yuan, Shuai; Zhou, Zhi-jie; Li, Jun; Wang, Fu-chen

2012-01-01

Highlights: ► Use a high-frequency furnace to study N-conversion during rapid pyrolysis of coal. ► Scarcely reported N-conversion during rapid pyrolysis of petroleum coke was studied. ► Both of NH 3 and HCN can be formed directly from coal during rapid pyrolysis. ► NH 3 –N yields are higher than HCN–N yields in most conditions. ► NH 3 –N yields of petroleum coke increase with temperature and no HCN detected. -- Abstract: Rapid pyrolysis of three typical Chinese coals, lignite from Inner Mongolia, bituminous from Shenfu coalfield, and anthracite from Guizhou, as well as a petroleum coke were carried out in a drop-style high-frequency furnace. The reactor was induction coil heated and had a very small high-temperature zone, which could restrain secondary conversions of nitrogen products. The effects of temperature and coal rank on conversions of fuel-N to primary nitrogen products (char-N, HCN–N, NH 3 –N and (tar + N 2 )–N) have been investigated. The results showed that, the increasing temperature reduced the yields of char-N and promoted the conversion of fuel-N to N 2 . Char-N yields increased, while volatile-N yields decreased as the coal rank increased. In most of the conditions, NH 3 –N yields were higher than HCN–N yields during rapid pyrolysis of coal. In the case of petroleum coke, NH 3 –N yields increased gradually with the increasing temperature, but no HCN was detected. We argue that NH 3 –N can be formed directly through the primary pyrolysis without secondary reactions. Although volatile-N yields of lignite were higher than those of bituminous, yields of (HCN + NH 3 )–N in volatile-N of lignite were lower than those of bituminous. While the (HCN + NH 3 )–N yields of anthracite were the lowest of the three coals. Both of the (HCN + NH 3 )–N yields and (HCN + NH 3 )–N proportions in volatile-N of petroleum coke were lower than the three coals.

Integrated report on the toxicological mitigation of coal liquids by hydrotreatment and other processes. [Petroleum and coal-derived products

Energy Technology Data Exchange (ETDEWEB)

Guerin, M.R.; Griest, W.H.; Ho, C.H.; Smith, L.H.; Witschi, H.P.

1986-06-01

Research here on the toxicological properties of coal-derived liquids focuses on characterizing the refining process and refined products. Principle attention is given to the potential tumorigenicity of coal-derived fuels and to the identification of means to further reduce tumorigenicity should this be found necessary. Hydrotreatment is studied most extensively because it will be almost certainly required to produce commercial products and because it is likely to also greatly reduce tumorigenic activity relative to that of crude coal-liquid feedstocks. This report presents the results of a lifetime C3H mouse skin tumorigenicity assay of an H-Coal series of oils and considers the relationships between tumorigenicity, chemistry, and processing. Lifetime assay results are reported for an H-Coal syncrude mode light oil/heavy oil blend, a low severity hydrotreatment product, a high severity hydrotreatment product, a naphtha reformate, a heating oil, a petroleum-derived reformate, and a petroleum derived heating oil. Data are compared with those for an earlier study of an SRC-II blend and products of its hydrotreatment. Adequate data are presented to allow an independent qualitative assessment of the conclusions while statistical evaluation of the data is being completed. The report also documents the physical and chemical properties of the oils tested. 33 refs., 14 figs., 53 tabs.

Irradiation tests on bitumen and bitumen coated materials

International Nuclear Information System (INIS)

Tabardel-Brian, R.; Rodier, J.; Lefillatre, G.

1969-01-01

The use of bitumen as a material for coating high-activity products calls for prior study of the resistance of bitumen to irradiation. After giving briefly the methods of preparation of bitumen- coated products, this report lists the equipment which has been used for carrying out the β and γ irradiations of these products, and gives the analytical results obtained as a function of the dose rates chosen and of the total integrated dose. Finally, some conclusions have been drawn concerning the best types of bitumen. It should be stressed that some bitumens apparently underwent no degradation whatsoever nor any volume increase, for a total integrated dose of 1.8 x 10 10 rads. (authors) [fr

1952 : bitumen beginnings

International Nuclear Information System (INIS)

Anon.

2008-01-01

In 1952, Imperial Oil used trains to deliver the first volumes of Alberta crude to the west coast. The Trans Mountain crude oil pipeline system was completed in 1953. Even in the early 1950s, the McMurray tar sands were recognized as the world's largest source of petroleum, containing an estimated 100 to 300 billion barrels of bitumen. A group of 10 companies had taken out permit rights on 250,000 acres in Alberta, just west of the Saskatchewan border. They began a core hole drilling program on the leases that are now part of Syncrude Canada and Suncor extraction projects. An experimental extraction operation was also carried out by Swedish Shale Oil Company to determine the economic feasibility of oil sands development. The bitumen extraction process used at the Bitumount plant involved heat. The Sun Oil Company applied for permits covering 100,000 acres on the east side of the Athabasca River, near the Bitumount plant. The leases are currently incorporated into several oilsands development projects, including Syncrude Canada's Aurora mine. At the time, Sun Oil also launched a core hole drilling program with plans to conduct further exploratory and development drilling. Other key events in 1952 included the Bonnie Glen discovery well that produced 240 barrels per day, and approval to export gas from the Peace River region. 1 tab., 1 fig

Process for agglomerating fine coal

Energy Technology Data Exchange (ETDEWEB)

Austin, L J; Misbach, P

1976-06-24

The invention concerns a process for agglomerating black coal in mud or powder form in the presence of a mineral oil product dispersed in water. During this process, the nutty slack is added to a portion - approximately 5 - 15% of its weight in the case of anhydrous coal - of a bitumen emulsion and thoroughly mixed. The emulsion should contain mineral oil bitumen with a penetration value 25/sup 0/ less than 5, or a Conradson value of over 35. In a further finishing process the emulsion contains alkaline naphthenate.

Impact of co-combustion of petroleum coke and coal on fly ash quality: Case study of a Western Kentucky power plant

International Nuclear Information System (INIS)

Hower, James C.; Thomas, Gerald A.; Mardon, Sarah M.; Trimble, Alan S.

2005-01-01

Petroleum coke has been used as a supplement or replacement for coal in pulverized-fuel combustion. At a 444-MW western Kentucky power station, the combustion of nearly 60% petroleum coke with moderate- to high-sulfur Illinois Basin coal produces fly ash with nearly 50% uncombusted petroleum coke and large amounts of V and Ni when compared to fly ash from strictly pulverized coal burns. Partitioning of the V and Ni, known from other studies to be concentrated in petroleum coke, was noted. However, the distribution of V and Ni does not directly correspond to the amount of uncombusted petroleum coke in the fly ash. Vanadium and Ni are preferentially associated with the finer, higher surface area fly ash fractions captured at lower flue gas temperatures. The presence of uncombusted petroleum coke in the fly ash doubles the amount of ash to be disposed, makes the fly ash unmarketable because of the high C content, and would lead to higher than typical (compared to other fly ashes in the region) concentrations of V and Ni in the fly ash even if the petroleum coke C could be beneficiated from the fly ash. Further studies of co-combustion ashes are necessary in order to understand their behavior in disposal

The big bitumen breakthrough

International Nuclear Information System (INIS)

Koch, G.

1996-01-01

The ongoing transformation of the oilsands and heavy oil sector from a poor cousin a few years ago into the cornerstone of the Alberta oil industry, was discussed. Much of this change is due to the development of SAGD (steam assisted gravity drainage) technology for the underground recovery of heavy oil and tarry bitumens, aided by partly government-funded research, and boosted by a revised provincial royalty regime. The thermal recovery process makes use of a pair of horizontal injection and recovery wells, drilled one above the other. The efficiency of this new technology could produce a shift in the petroleum industry's spending towards oil sands and heavy oil if investors conclude that it is more profitable to produce heavy oil than conventional light oil. Some of the oil sands producers that are poised to invest billions of dollars in various underground bitumen projects in Alberta over the next five years include Suncor, Syncrude, Alberta Energy Co., Amoco Canada, Elan Energy, Imperial Oil Resources, CS Resources, Koch Oil, and Gulf Resources. The ultimate goal is recovery costs of $6 per barrel, which is comparable to the costs of the conventional oil sector. The added advantage of oil sands production is, of course, the virtual elimination of the exploration risk. 3 figs

Decreasing polycyclic aromatic hydrocarbons emission from bitumen using alternative bitumen production process

International Nuclear Information System (INIS)

Rasoulzadeh, Y.; Mortazavi, S.B.; Yousefi, A.A.; Khavanin, A.

2011-01-01

In 1988, the National Institute for Occupational Safety and Health (NIOSH) recommended that bitumen fumes should also be considered a potential occupational carcinogen and management practices such as engineering controls should be implemented. Changing the production process of bitumen, as a source control method, was investigated in our study. For the first time, a novel alternative process was used to produce paving grade bitumen with decreased PAH emissions as well as improved bitumen performance grade (PG). Post-consumer latex and natural bitumen (NB) were used as additives to obtain 60/70 modified bitumen directly from the vacuum bottom (VB) without any need for air-blowing. The emissions were produced by a laboratory fume generation rig and were sampled and analyzed by GC-Mass and GC-FID as described in NIOSH method 5515. The PG of the resulting modified 60/70 bitumen in this study covers a wider range of climatic conditions and has higher total resistance against deformation than conventional 60/70 bitumen. The total PAH emissions from modified 60/70 bitumen (100.2619 ng/g) were decreased approximately to 50% of PAHs emitted from conventional 60/70 bitumen (197.696 ng/g). Therefore, it is possible to obtain modified bitumen with lower PAH emissions and better quality than conventional bitumen via additives and without air-blowing.

The pentane- and toluene-soluble fractions of a petroleum residue and three coal tars by size exclusion chromatography and UV-fluorescence spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Karaca, F.; Millan-Agorio, M.; Morgan, T.J.; Bull, I.D.; Herod, A.A.; Kandiyoti, R. [University of London Imperial College Science Technology & Medicine, London (United Kingdom). Dept. of Chemical Engineering

2008-01-15

A petroleum atmospheric pressure distillate residue and three tars derived from different coals using different severities of thermal treatment were separated into seven fractions using column chromatography on silica and sequential elution by the solvent sequence pentane, toluene, acetonitrile, pyridine, 1-methyl-2-pyrrolidinone (NMP) and water. The fractions from the four extractions have been compared using size exclusion chromatography (SEC) in NMP as eluent and by synchronous ultra-violet-fluorescence (UV-F). This paper concerns the pentane and toluene soluble fractions only since these are the least polar fractions. By SEC, the size of the aromatic molecules increased from the first pentane soluble fractions to the toluene-soluble fractions, with the petroleum residue fractions of larger size than the equivalent fractions from coal liquids. The three coal tars showed significant differences, indicating that temperature of pyrolysis had a significant effect on the molecular size. Synchronous UV-F spectra of the four sets of fractions, in solution in NMP, again showed significant differences between the petroleum residue and the coal tars, as well as amongst the three coal tars. In general, the petroleum residue fractions contained smaller aromatic clusters than the coal liquid fractions. These low-polarity fractions contained material excluded from the column porosity in SEC that was unlikely to consist of aggregates of polar molecules.

Volume Stability of Bitumen Bound Building Blocks

Directory of Open Access Journals (Sweden)

Thanaya I.N.A.

2010-01-01

Full Text Available This paper covers results of laboratory investigations on the volume stability of masonry units incorporating waste materials bound with bitumen (Bitublocks, due to moisture adsorption, thermal exposure and vacuum saturation. The materials used were steel slag, crushed glass, coal fly ash, and 50 pen bitumen. The samples were produced in hot mix method, compacted, then exposed to moist and temperature. It was found that moisture adsorption from the environment caused the Bitublock to expand. The samples with less intense curing regime experienced lower expansion and became stable faster, and vice versa. Under thermal condition (at 70°C, the samples with less intense curing regime underwent higher expansion, and vice versa. They were also highly reversible. Their volume stability was found unique under water exposure. The expansion on first vacuum saturation cycle was irreversible, then largely reversible on the following cycles.

Methods for producing and upgrading liquid hydrocarbons from Alberta coal. [Canada - Alberta

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

Production of synthetic crude oils by co-processing coal and heavy oil or bitumen has been the subject of research efforts in Alberta since 1979. This booklet describes the treatment that is necessary for these crude oils to become suitable as feedstocks for refineries as evolved in research projects. Sections are headed: hydroprocessing of coal-based liquids; functional group analysis; isotopic studies of co-processing schemes; chemistry of coal liquefaction; co-processing process development; molecular interactions between heavy oil and coal species during co-processing; combined processing of coal, heavy oil and natural gas; and coprocessing of coal and bitumen with molten halide catalysts. 33 refs., 8 figs.

Life-cycle greenhouse gas emissions of shale gas, natural gas, coal, and petroleum.

Science.gov (United States)

Burnham, Andrew; Han, Jeongwoo; Clark, Corrie E; Wang, Michael; Dunn, Jennifer B; Palou-Rivera, Ignasi

2012-01-17

The technologies and practices that have enabled the recent boom in shale gas production have also brought attention to the environmental impacts of its use. It has been debated whether the fugitive methane emissions during natural gas production and transmission outweigh the lower carbon dioxide emissions during combustion when compared to coal and petroleum. Using the current state of knowledge of methane emissions from shale gas, conventional natural gas, coal, and petroleum, we estimated up-to-date life-cycle greenhouse gas emissions. In addition, we developed distribution functions for key parameters in each pathway to examine uncertainty and identify data gaps such as methane emissions from shale gas well completions and conventional natural gas liquid unloadings that need to be further addressed. Our base case results show that shale gas life-cycle emissions are 6% lower than conventional natural gas, 23% lower than gasoline, and 33% lower than coal. However, the range in values for shale and conventional gas overlap, so there is a statistical uncertainty whether shale gas emissions are indeed lower than conventional gas. Moreover, this life-cycle analysis, among other work in this area, provides insight on critical stages that the natural gas industry and government agencies can work together on to reduce the greenhouse gas footprint of natural gas.

Treatment of products from petroleum, shale, coal, lignite, etc

Energy Technology Data Exchange (ETDEWEB)

Jevanoff, V

1952-06-20

An improved process is described for treating with sodium plumbite all the products derived from crude petroleum, bituminous shale, coal, lignite, peat, etc., such as gasoline, solvents, lamp oil, gas oil, fuels, etc; the process being essentially characterized by the fact that it consists first in washing the product to be refined with a soda wash; submitting it to a treatment with sodium plumbite, without addition of sulfur, then to eliminate the sulfur plumbite compounds resulting in the treated product, using either redistillation to eliminate products remaining in the residue or filtration over an absorbing material such as active carbon, decolorizing earths.

Coal and petroleum resources in the Appalachian basin: index maps of included studies: Chapter B.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Ruppert, Leslie F.; Trippi, Michael H.; Kinney, Scott A.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

This chapter B.1 of U.S. Geological Survey (USGS) Professional Paper 1708 provides index maps for many of the studies described in other chapters of the report. Scientists of the USGS and State geological surveys studied coal and petroleum resources in the central and southern Appalachian structural basins. In the southern Appalachian basin, studies focused on the coal-bearing parts of the Black Warrior basin in Alabama. The scientists used new and existing geologic data sets to create a common spatial geologic framework for the fossil-fuel-bearing strata of the central Appalachian basin and the Black Warrior basin in Alabama.

Mechanical characterization of Portland cement mortars containing petroleum or coal tar

Directory of Open Access Journals (Sweden)

Garcés, P.

2007-08-01

Full Text Available This article discusses experimental data on the flexural and compressive strength of Portland cement mortars containing additions or cement replacements consisting in petroleum or coal tar, by-products of the oil and coal industries. The materials studied were two coal (BACA and BACB and two petroleum (BPP and BPT tars. The results show that it is feasible to use such materials as a partial replacement for cement in mortar manufacture. This should lead to the design of a new sustainable product that will contribute to lowering the environmental impact of construction materials while at the same time opening up an avenue for the re-use of this type of industrial by-products.En este artículo se presentan datos experimentales de resistencia a flexión y a compresión de morteros de cemento Portland con adición y sustitución de breas de petróleo y de alquitrán de carbón, que son subproductos de la industria del carbón o del petróleo. Los materiales estudiados son breas de alquitrán de carbón A (BACA y B (BACB, y dos breas de petróleo (BPP y (BPT. Los datos demuestran la viabilidad del uso de estas breas en la fabricación de morteros con menores contenidos de cemento, permitiendo diseñar un nuevo material sostenible con el medio ambiente y que contribuya a reducir el impacto ambiental de los materiales de construcción, hecho que permite abrir una nueva vía de valorización de estos subproductos.

REDUCING POWER PRODUCTION COSTS BY UTILIZING PETROLEUM COKE

Energy Technology Data Exchange (ETDEWEB)

Kevin C. Galbreath; Donald L. Toman; Christopher J. Zygarlicke

1999-09-01

Petroleum coke, a byproduct of the petroleum-refining process, is an attractive primary or supplemental fuel for power production primarily because of a progressive and predictable increase in the production volumes of petroleum coke (1, 2). Petroleum coke is most commonly blended with coal in proportions suitable to meet sulfur emission compliance. Petroleum coke is generally less reactive than coal; therefore, the cofiring of petroleum coke with coal typically improves ignition, flame stability, and carbon loss relative to the combustion of petroleum coke alone. Although petroleum coke is a desirable fuel for producing relatively inexpensive electrical power, concerns about the effects of petroleum coke blending on combustion and pollution control processes exist in the coal-fired utility industry (3). The Energy & Environmental Research Center (EERC) completed a 2-year technical assessment of petroleum coke as a supplemental fuel. A survey questionnaire was sent to seven electric utility companies that are currently cofiring coal and petroleum coke in an effort to solicit specific suggestions on research needs and fuel selections. An example of the letter and survey questionnaire is presented in Appendix A. Interest was expressed by most utilities in evaluating the effects of petroleum coke blending on grindability, combustion reactivity, fouling, slagging, and fly ash emissions control. Unexpectedly, concern over corrosion was not expressed by the utilities contacted. Although all seven utilities responded to the question, only two utilities, Northern States Power Company (NSP) and Ameren, sent fuels to the EERC for evaluation. Both utilities sent subbituminous coals from the Power River Basin and petroleum shot coke samples. Petroleum shot coke is produced unintentionally during operational upsets in the petroleum refining process. This report evaluates the effects of petroleum shot coke blending on grindability, fuel reactivity, fouling/slagging, and

40 CFR 60.101a - Definitions.

Science.gov (United States)

2010-07-01

... or converting the SO2 to a sulfur product. Petroleum means the crude oil removed from the earth and the oils derived from tar sands, shale, and coal. Petroleum refinery means any facility engaged in producing gasoline, kerosene, distillate fuel oils, residual fuel oils, lubricants, asphalt (bitumen) or...

Hydrotreating of coal-derived liquids

Energy Technology Data Exchange (ETDEWEB)

Lott, S.E.; Stohl, F.V.; Diegert, K.V. [Sandia National Lab., Albuquerque, NM (United States)] [and others

1995-12-31

To develop a database relating hydrotreating parameters to feed and product quality by experimentally evaluating options for hydrotreating whole coal liquids, distillate cuts of coal liquids, petroleum, and blends of coal liquids with petroleum.

Our petroleum legacy: The Alberta story

International Nuclear Information System (INIS)

Bott, R.

1992-11-01

Background information is presented on the importance of the petroleum industry in Alberta. Alberta holds over 70% of Canada's coal and natural gas reserves and, if bitumen is included, over 90% of Canada's established oil reserves. Alberta's major exports are dominated by crude oil and related products ($9.6 billion in 1990) and the oil and gas sector had $15.7 billion in revenues in 1991, over 4 times as much as the next most important sector, agriculture. About 140,000 Albertans are directly or indirectly employed in the oil and gas industry, about 11% of employed persons. The industry's capital spending in Alberta was $5.3 billion in 1991, and its total expenditures were about $15 billion, and during the 1980s the industry paid about $42 billion to the Alberta government in the form of taxes, royalties, and other fees. Other benefits of the oil and gas industry's presence in Alberta include those related to its employment of a skilled workforce, its advanced research capabilities, and economic spinoff effects from employment and technological development. The influence of recent events on the industry is outlined, including the effects of international energy commodity markets, deregulation, and higher exploration and development costs. The declining financial viability of the Alberta petroleum industry is noted and its future is discussed in the light of such factors as oil prices, markets, new technologies, environmental constraints, and the volume of new discoveries. 9 refs., 5 figs., 1 tab

Pipeline transportation of emerging partially upgraded bitumen

International Nuclear Information System (INIS)

Luhning, R.W.; Anand, A.; Blackmore, T.; Lawson, D.S.

2002-01-01

The recoverable reserves of Canada's vast oil deposits is estimated to be 335 billion barrels (bbl), most of which are in the Alberta oil sands. Canada was the largest import supplier of crude oil to the United States in 2001, followed by Saudi Arabia. By 2011, the production of oil sands is expected to increase to 50 per cent of Canada's oil, and conventional oil production will decline as more production will be provided by synthetic light oil and bitumen. This paper lists the announced oil sands projects. If all are to proceed, production would reach 3,445,000 bbl per day by 2011. The three main challenges regarding the transportation and marketing of this new production were described. The first is to expand the physical capacity of existing pipelines. The second is the supply of low viscosity diluent (such as natural gas condensate or synthetic diluent) to reduce the viscosity and density of the bitumen as it passes through the pipelines. The current pipeline specifications and procedures to transport partially upgraded products are presented. The final challenge is the projected refinery market constraint to process the bitumen and synthetic light oil into consumer fuel products. These challenges can be addressed by modifying refineries and increasing Canadian access in Petroleum Administration Defense District (PADD) II and IV. The technology for partial upgrading of bitumen to produce pipeline specification oil, reduce diluent requirements and add sales value, is currently under development. The number of existing refineries to potentially accept partially upgraded product is listed. The partially upgraded bitumen will be in demand for additional upgrading to end user products, and new opportunities will be presented as additional pipeline capacity is made available to transport crude to U.S. markets and overseas. The paper describes the following emerging partial upgrading methods: the OrCrude upgrading process, rapid thermal processing, CPJ process for

Project scenarios for bitumen upgrading

International Nuclear Information System (INIS)

Koppel, P.E.; Mazurek, W.L.; Harji, A.

2002-01-01

The established reserves of Alberta's heavy oil resources are 178 billion barrels, and potential recoverable reserves are 315 billion barrels. The challenge of production includes the logistics of recovery, upgrading and transportation to market. Utilization of the bitumen is not simple because bitumen is too viscous to transport by pipeline. In addition, it is not processable by most existing refineries unless it can be upgraded through dilution. This paper examined different factors regarding the economic viability of various upgrading methods of a wide range of bitumen feedstocks. The study also examined the sensitivity of refinery demand to the prices of these feedstocks, along with the competitiveness among bitumen-based feedstock and conventional crudes. Western Canada, Ontario and the PADD II district in the United States are the 3 major markets for western Canadian bitumen based feedstock, the demand for which depends on refinery configurations and asphalt demand. This paper described the following 4 generic scenarios that describe Alberta bitumen upgrading projects: (1) adjacent to open pit mines, (2) adjacent to steam assisted gravity drainage (SAGD) facilities, (3) remotely located from resource production at an existing refinery, and (4) pipeline bitumen. It was noted that producers should determine the best way to upgrade the bitumen to ensure there is an economic market for the product, but they should also be aware not to over process the bitumen so as not to leave existing refinery facilities under-utilized. 2 refs., 1 tab., 3 figs

Properties and long-term behaviour of bitumen and radioactive waste-bitumen mixtures

International Nuclear Information System (INIS)

Eschrich, H.

1980-10-01

Part I represents a survey of the properties and the long-term behaviour of pure bitumens and mixtures of bitumens with radioactive reactor and reprocessing wastes. This survey includes information on the origin, amounts, and composition of the various wastes considered for bituminization and the different waste bituminization techniques used. The influence of various factors on the quality of waste-bitumen products and on the radiological safety during transport, short- and long-term storage of the final products is described. Special consideration is given to the most important safety relevant factors associated to the use of bitumen as matrix material for radioactive wastes, such as leach-resistance, radiolysis, chemical and mechanical stability, combustibility, and microbial attack. Part II consists of a comprehensive bibliography on the bituminization of radioactive wastes, giving about 300 references to literature published from the beginning of the use of bitumen in radioactive waste management in 1960 until the beginning of 1979. Methods for the quality control of bituminous materials and some useful data are given in an annex. (author)

Process from removing benzine, toluene, etc. , from petroleum residues, coal tar, and shale tar, etc

Energy Technology Data Exchange (ETDEWEB)

Hlawaty, F

1888-08-11

A process is described for the preparation of ligroin and its homologs as well as naphthalene and anthracene consisting in leading superheated water vapor into a mixture of petroleum residues (or mineral coal tar, etc.) heated to about 400/sup 0/C with cellulosic substances as sage shreds, sea grass, or straw, with addition of caustic alkali.

Shale oil. I. Genesis of oil shales and its relation to petroleum and other fuels

Energy Technology Data Exchange (ETDEWEB)

McKee, R H; Manning, P D.V.

1927-01-01

Oil-shale kerogen originated from resinous vegetation residues of past eras, whereas well petroleum was formed from oil shales by pressure and mild heat. Petroleum migrated to its present reservoir from neighboring oil-shale deposits, leaving a residue of black bituminous shales. The high carbon dioxide content of gases present in petroleum wells originated from kerogen, as it gives off carbon dioxide gas before producing soluble oil or bitumen.

Process and apparatus for recovering of oil, bitumen, tar, resins, etc

Energy Technology Data Exchange (ETDEWEB)

1921-11-06

A process for recovering oil, bitumen, tar, and resins from oil shale, oil sands, Fuller's earth, peat, brown coal, mineral coal, and wood, through direct action of superheated steam on the material, is characterized by the fact that superheated steam with or without mixing of inert gases at a temperature, which lies below the decomposition temperature of the material being treated, is passed through the material with a high velocity. It leaves through nozzles, used in steam turbines. A method of carrying out the process in which solution medium is used for action on the material is characterized by the fact that solvents such as benzine and benzol are mixed with steam in different quantities.

Chemical and physical aspects of refining coal liquids

Science.gov (United States)

Shah, Y. T.; Stiegel, G. J.; Krishnamurthy, S.

1981-02-01

Increasing costs and declining reserves of petroleum are forcing oil importing countries to develop alternate energy sources. The direct liquefaction of coal is currently being investigated as a viable means of producing substitute liquid fuels. The coal liquids derived from such processes are typically high in nitrogen, oxygen and sulfur besides having a high aromatic and metals content. It is therefore envisaged that modifications to existing petroleum refining technology will be necessary in order to economically upgrade coal liquids. In this review, compositional data for various coal liquids are presented and compared with those for petroleum fuels. Studies reported on the stability of coal liquids are discussed. The feasibility of processing blends of coal liquids with petroleum feedstocks in existing refineries is evaluated. The chemistry of hydroprocessing is discussed through kinetic and mechanistic studies using compounds which are commonly detected in coal liquids. The pros and cons of using conventional petroleum refining catalysts for upgrading coal liquids are discussed.

Techno-economic assessment of hydrogen production from underground coal gasification (UCG) in Western Canada with carbon capture and sequestration (CCS) for upgrading bitumen from oil sands

International Nuclear Information System (INIS)

Olateju, Babatunde; Kumar, Amit

2013-01-01

Highlights: • Development of a techno-economic model for UCG-CCS and SMR-CCS. • Estimation of H 2 production costs with and without CCS for UCG and SMR. • UCG is more economical for H 2 production with CCS. • SMR is more cost efficient for H 2 production without CCS. • Cost competiveness is highly sensitive to the IRR differential between UCG and SMR. - Abstract: This paper examines the techno-economic viability of hydrogen production from underground coal gasification (UCG) in Western Canada, for the servicing of the oil sands bitumen upgrading industry. Hydrogen production for bitumen upgrading is predominantly achieved via steam methane reforming (SMR); which involves significant greenhouse gas (GHG) emissions along with considerable feedstock (natural gas) cost volatility. UCG is a formidable candidate for cost-competitive environmentally sustainable hydrogen production; given its negligible feedstock cost, the enormity of deep coal reserves in Western Canada and the favourable CO 2 sequestration characteristics of potential UCG sites in the Western Canadian sedimentary basin (WCSB). Techno-economic models were developed for UCG and SMR with and without CCS, to estimate the cost of hydrogen production including delivery to a bitumen upgrader. In this paper, at base case conditions, a 5% internal rate of return (IRR) differential between UCG and SMR was considered so as to account for the increased investment risk associated with UCG. The cost of UCG hydrogen production without CCS is estimated to be $1.78/kg of H 2 . With CCS, this increases to range of $2.11–$2.70/kg of H 2 , depending on the distance of the site for CO 2 sequestration from the UCG plant. The SMR hydrogen production cost without CCS is estimated to be $1.73/kg of H 2 . In similar fashion to UCG, this rises to a range of $2.14 to $2.41/kg of H 2 with the consideration of CCS. Lastly, for hydrogen production without CCS, UCG has a superior cost competitiveness in comparison to SMR

Biological monitoring as a useful tool for the detection of a coal-tar contamination in bitumen-exposed workers

Energy Technology Data Exchange (ETDEWEB)

Raulf-Heimsoth, M.; Angerer, J.; Pesch, B.; Marczynski, B.; Hahn, J.U.; Spickenheuer, A.; Preuss, R.; Ruhl, R.; Rode, P.; Bruning, T. [Institute at the Ruhr University of Bochum, Bochum (Germany)

2008-07-01

In our research project entitled 'Chemical irritative and/or genotoxic effect of fumes of bitumen under high processing temperatures on the airways,' 73 mastic asphalt workers exposed to fumes of bitumen and 49 construction nonexposed workers were analyzed and compared with respect to polycyclic aromatic hydrocarbons (PAHs) exposure and exposure-related health effects. In order to assess the internal exposure the monohydroxylated metabolites of pyrene, 1-hydroxypyrene (1-OHP), and phenanthrene, 1-, 2- and 9-, and 3- and 4-hydroxyphenanthrene (OHPH) were determined in pre- and post-shift urinary samples. Significantly higher concentrations 1-OHP and OHPH were detected in the post-shift urine samples of 7 mastic asphalt workers working on the same construction site compared to the reference workers and all other 66 mastic asphalt workers. The adjusted mean OHPH in the reference, 66 mastic worker, and 7 worker subgroups was 1022, 1544, and 12919 ng/g creatinine (crn) respectively, indicating a marked rise in the 7 worker subgroup. In addition, there was a more than 12-fold increase of PAH metabolites from pre- to post-shift in these 7 workers, whereas in the other mastic asphalt workers there was only a twofold rise in PAH-metabolite concentration between pre- and post-shift values. The analysis of a drilling core from the construction site of the seven workers led to the detection of the source for this marked PAH exposure during the working shift as being coal tar plates, which were, without knowledge of the workers and coordinators, the underground material of the mastic asphalt layer. The evaluation of the stationary workplace concentration showed enhanced levels of phenanthrene, pyrene, fluorene, anthracene, and acenaphthene during working shifts at the construction site of these seven workers. Our study shows that biological monitoring is also a useful tool for the detection of unrecognized sources with high PAH concentrations.

Ex-USSR: petroleum activities in 1991

International Nuclear Information System (INIS)

1992-01-01

This paper gives statistical data on economy and petroleum industry in ex-USSR: Primary energy production and consumption (coal, petroleum, natural gas, primary power), petroleum and natural gas reserves, drilling activity, exports and imports of petroleum products, refining capacity. 2 figs., 14 tabs

Advances in coal chemistry, 1950--1970. [21 refs

Energy Technology Data Exchange (ETDEWEB)

Brooks, J D

1971-12-01

During the 20 years under review, considerable advances were made at centers of coal research throughout the world in the determination of the chemical structure and reactions of coals. Important contributions came from the CSIRO group in Sydney. Activity was greatest during the first decade of the period under review and declined progressively during the second, as evidence of the extreme complexity of coal structures made it clear that further chemical research would be less rewarding. Some overseas investigations were related mainly to chemical processes for the conversion of coals to liquid and gaseous fuels, and to possible direct chemical utilization; but in Australia, because of the relatively small size of the potential market and the widely dispersed centers of population, such studies were not relevant to the current situation. Much of the Australian research in this field was related to carbonization processes and to the chemical and physical processes involved in the thermal treatment of coals. The high-light was perhaps the investigation, begun in 1960, which showed how coals, pitch, and bitumen resolidify during heating to form coke. Determinations were also made of the chemical composition of tars and pitches produced both industrially and in the laboratory and efforts were made to develop local outlets for these by-products of gas-making and of steelworks coke ovens. The pattern of Australian fuel consumption changed considerably during the 20-year period, and in particuar there was considerable development in the use of petroleum by-products for gas-making. Research on the manufacture of metallurgical coke was established within the steel industry, and in response to these factors basic work by CSIRO in bituminous coal chemistry had virtually ceased by the end of 1966.

Processing options for bitumen upgrading

International Nuclear Information System (INIS)

Harji, A.N.; Koppel, P.E.; Mazurek, W.L.; Meysami, P.

2003-01-01

It is estimated that 178 billion barrels of oil can be recovered from Alberta's vast heavy oil reserves. The challenge lies in the logistics of recovering, upgrading and transporting the oil to market. The Canadian Energy Research Institute conducted a recent study to determine market potential by 2007 for diluted bitumen and synthetic crude oil produced from upgraded bitumen. The viability for a wide range of bitumen feedstocks was assessed along with the sensitivity of refinery demand to their prices. The 3 major markets for western Canadian bitumen include PADD 2 in the United States, western Canada, and Ontario. Bitumen is too viscous to transport by pipeline and cannot be processed by most of the existing refineries. Therefore, in order to develop a mass market for the product, bitumen must undergo the energy intensive upgrading process at existing refineries. The factors impacting which method of upgrading is most suitable were discussed with particular attention to the impact that Canada's ratification of the Kyoto Protocol may have on Alberta's bitumen resource in terms of costs of complying with greenhouse gas reduction initiatives. The authors emphasized that it is crucial to customize an upgrading project to meet site and market specific factors. 8 refs., 3 tabs., 3 figs

Use and trade of bitumen in antiquity and prehistory: molecular archaeology reveals secrets of past civilizations

Science.gov (United States)

Connan, J.

1999-01-01

Natural asphalt (or bitumen) deposits, oil seepage and liquid oil shows are widespread in the Middle East, especially in the Zagros mountains of Iran. Ancient people from northern Iraq, south-west Iran and the Dead Sea area extensively used this ubiquitous natural resource until the Neolithic period (7000 to 6000 BC). Evidence of earlier use has been recently documented in the Syrian desert near El Kown, where bitumen-coated flint implements, dated to 40,000 BC (Mousterian period), have been unearthed. This discovery at least proves that bitumen was used by Neanderthal populations as hafting material to fix handles to their flint tools. Numerous testimonies, proving the importance of this petroleum-based material in Ancient civilizations, were brought to light by the excavations conducted in the Near East as of the beginning of the century. Bitumen remains show a wide range of uses that can be classified under several headings. First of all, bitumen was largely used in Mesopotamia and Elam as mortar in the construction of palaces (e.g. the Darius Palace in Susa), temples, ziggurats (e.g. the so-called 'Tower of Babel' in Babylon), terraces (e.g. the famous 'Hanging Gardens of Babylon') and exceptionally for roadway coating (e.g. the processional way of Babylon). Since the Neolithic, bitumen served to waterproof containers (baskets, earthenware jars, storage pits), wooden posts, palace grounds (e.g. in Mari and Haradum), reserves of lustral waters, bathrooms, palm roofs, etc. Mats, sarcophagi, coffins and jars, used for funeral practices, were often covered and sealed with bitumen. Reed and wood boats were also caulked with bitumen. Abundant lumps of bituminous mixtures used for that particular purpose have been found in storage rooms of houses at Ra's al-Junayz in Oman. Bitumen was also a widespread adhesive in antiquity and served to repair broken ceramics, fix eyes and horns on statues (e.g. at Tell al-Ubaid around 2500 BC). Beautiful decorations with stones

Report of National Research Institute for Pollution and Resources for fiscal 1979. Research on conversion of coal to petroleum, research on coal liquefaction, high pressure liquid phase hydrogenation of coal by continuous test equipment, and manufacture of coal chemicals; 1979 nendo sekitan no yuka no kenkyu / sekitan no ekika no kenkyu / renzoku shiken sochi ni yoru sekitan no koatsu ekiso suisoka bunkai / coal chemicals no seizo

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-07-01

Research was conducted on conversion of coal to petroleum for the purpose of securing substitute liquid fuel. Recovery of hydrogen from the waste gas from the conversion process was explained, as were the conversion results from various coals produced in Japan. In coal liquefaction researches with the aim of manufacturing artificial petroleum, a report was made on each of the researches, i.e., the experiment results of coal liquefaction using various catalysts, manufacture of hydrogen by water gas reaction, catalytic action against coal paste, action of mixed oil and pressure against coal paste, result of hydrogen adding test for coal paste using an intermediate scale device, test result of secondary hydrogen addition for coal liquefied oil, and the test result of continuous secondary hydrogen addition for the liquefied oil. In the manufacture of fuel oil by hydro-cracking of coal or tar, a report was made on high pressure liquid phase hydrogenation of coal using a continuous testing device. Aromatic chemicals useful as chemical materials are supposed to be obtained by cutting inter-polymerized-unit bonding to make low molecules from the chemical structure of coal, removing surrounding radicals and simplifying it. A report was also made on the experiment of manufacturing coal chemicals by combination of high pressure liquid phase hydrogenation and hydro-dealkylation. (NEDO)

Organic sulphur in macromolecular sedimentary organic matter. II. Analysis of distributions of sulphur-containing pyrolysis products using multivariate techniques

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Eglinton, T.I.; Pool, W.; Leeuw, J.W. de; Eijkel, G.; Boon, J.J.

1992-01-01

This study describes the analysis of sulphur-containing products from Curie-point pyrolysis (Py) of eighty-five samples (kerogens, bitumen, and petroleum asphaltenes and coals) using gas chromatography (GC) in combination with sulphur-selective detection. Peak areas of approximately forty individual

Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

Fossil fuels from the Appalachian basin region have been major contributors to the Nation’s energy supplies over much of the last three centuries. Appalachian coal and petroleum resources are still available in sufficient quantities to contribute significantly to fulfilling the Nation’s energy needs. Although both conventional oil and gas continue to be produced in the Appalachian basin, most new wells in the region are drilled in shale reservoirs to produce natural gas.

Ultrasound-assisted oxidative desulfurization of bitumen

Science.gov (United States)

Kamal, Wan Mohamad Ikhwan bin Wan; Okawa, Hirokazu; Kato, Takahiro; Sugawara, Katsuyasu

2017-07-01

Bitumen contains a high percentage of sulfur (about 4.6 wt %). A hydrodesulfurization method is used to remove sulfur from bitumen. The drawback of this method is the requirement for a high temperature of >300 °C. Most of the sulfur in bitumen exists as thiophene. Oxidative desulfurization (ODS), involving oxidizing sulfur using H2O2, then removing it using NaOH, allows the removal of sulfur in thiophene at low temperatures. We removed sulfur from bitumen using ODS treatment under ultrasound irradiation, and 52% of sulfur was successfully removed. Additionally, the physical action of ultrasound assisted the desulfurization of bitumen, even at low H2O2 concentrations.

33rd annual technical meeting of the Petroleum Society of CIM

Energy Technology Data Exchange (ETDEWEB)

1982-03-01

This meeting report of a conference on 'Energy Self-Sufficiency: Dream or Reality.' to be held in Calgary June 6-9, 1982 gives details of the program and contains abstracts of the 99 papers. Ten of these concern coal. Topics include temperature and cavity configuration modelling associated with moving boundary in underground coal conversion; modelling of underground coal gasification; coal liquefaction heat transfer coefficients; viscosity of coal-bitumen and coal-anthracene oil slurries; economic extraction of methane through coal demethanation; coal and solid waste burning Stirling engines; Canadian program for underground coal conversion; effect of moisture on the behaviour of shales and roof bolt anchoring capacity; effect of weak floor interaction on stability of coal pillars; and pressures in coal silos.

Bioremediation of petroleum hydrocarbons in soil environments. Report No. EE-141

Energy Technology Data Exchange (ETDEWEB)

Rowell, M J; Ashworth, J; Qureshi, A A

1992-01-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed by means of a literature survey and also through discussions with workers in relevent disciplines. This report discusses both the impacts of hydrocarbons on soil and a range of methods available to assist in the decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, oily sludges, asphalts and bitumens, drilling mud residues, creosote tars and some pesticides.

Chemical reaction engineering studies on cocracking of petroleum vacuum residue with coal, plastics, and biomass (bagasse and petrocrop)

Energy Technology Data Exchange (ETDEWEB)

Ahmaruzzaman, M.; Sharma, D.K. [Indian Institute of Technology, New Delhi (India). Centre for Energy Studies

2007-07-01

This article deals with the studies on cocracking of petroleum vacuum residue (XVR) with thermosetting plastic, I. e., bakelite (BL), Samla coal (SC), biomass, I. e., bagasse (BG) or C. procera (CL) and their binary, ternary, and quaternary mixtures in a thermogravimetric analyzer (TGA). The kinetic studies were performed using the Coats and Redfern kinetic modeling equation. The overall activation energies obtained were 25 kJ/mole for petroleum vacuum residue, 99 kJ/mole for polypropylene, 21 kJ/mole for coal, 23 kJ/mole for Calotropis procera, and 25 kJ/mole for the combination of these four materials. However, other models, such as van Krevelan et al. and Horowitz and Metzger have also been used in some cases to compare the results with those obtained by the Coats and Redfern kinetic models. In the present work, the effect of catalysts on the cracking of Basra vacuum residue (BVR) has also been reported.

Coal liquefaction technologies for producing ultra clean fuel

International Nuclear Information System (INIS)

Tahir, M.S.; Haq, N.U.; Nasir, H.; Islam, N.

2011-01-01

The expanding demand for petroleum, accompanied by the diminishing petroleum reserves and the energy security, has intensified the significance in coal liquefaction technologies (CTL) globally and specially in Pakistan. Pakistan is rich in coal resources, but short of petroleum. The Geological Survey of Pakistan based on wide spread drilling over an area of 9000 sq. km, a total of 175 billion tons of coal resource potential has been assessed. This paper overviews a general introduction on the mechanisms and processes of CLT such as direct coal liquefaction (DCL) and indirect coal liquefaction (ICL) technologies. (author)

Organic metamorphism in the California petroleum basins; Chapter B, Insights from extractable bitumen and saturated hydrocarbons

Science.gov (United States)

Price, Leigh C.

2000-01-01

Seventy-five shales from the Los Angeles, Ventura, and Southern San Joaquin Valley Basins were extracted and analyzed. Samples were chosen on the basis of ROCK-EVAL analyses of a much larger sample base. The samples ranged in burial temperatures from 40 ? to 220 ? C, and contained hydrogen-poor to hydrogen-rich organic matter (OM), based on OM visual typing and a correlation of elemental kerogen hydrogen to carbon ratios with ROCK-EVAL hydrogen indices. By extractable bitumen measurements, rocks with hydrogen- poor OM in the Los Angeles Basin began mainstage hydrocarbon (HC) generation by 90 ? C. The HC concentrations maximized by 165 ? C, and beyond 165 ? C, HC and bitumen concentrations and ROCK-EVAL hydrogen indices all began decreasing to low values reached by 220 ? C, where HC generation was largely complete. Rocks with hydrogen-poor OM in the Southern San Joaquin Valley Basin commenced mainstage HC generation at 135 ? C and HC concentrations maximized by 180 ? C. Above 180 ? C, HC and bitumen concentrations and ROCK-EVAL hydrogen indices all decreased to low values reached by 214 ? C, again the process of HC generation being largely complete. In both cases, bell-shaped HC-generation curves were present versus depth (burial temperature). Mainstage HC generation had not yet begun in Ventura Basin rocks with hydrogen-poor OM by 140 ? C. The apparent lower temperature for initiation of mainstage generation in the Los Angeles Basin is attributed to very recent cooling in that basin from meteoric-water flow. Thus, HC generation there most probably occurred at higher burial temperatures. In contrast, mainstage HC generation, and all aspects of organic metamorphism, were strongly suppressed in rocks with hydrogen-rich OM at temperatures as high as 198 ? C. For example, shales from the Wilmington field (Los Angeles Basin) from 180 ? to 198 ? C retained ROCK-EVAL hydrogen indices of 550- 700 and had saturated-HC coefficients of only 4-15 mg/g organic carbon. The rocks

Methods for producing and upgrading liquid hydrocarbons from Alberta coal

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

This publication describes a number of research projects into hydrotreating, the treatment necessary for synthetic crude oils to become suitable as feedstocks for refineries. The projects include the hydroprocessing of coal-based liquids, functional group analysis, isotopic studies of co-processing schemes, and co-processing coal and bitumen with molten halide catalysts.

Taking the petroleum out of petrochemistry

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, T

1982-01-01

It is thought to be inevitable that world production of petroleum will start declining in the not too distant future. When this happens, the only feedstock for the organic chemicals industry and the polymer chemistry industry will be coal. It is emphasized that the best way of substituting coal for petroleum fractions as an alternative energy source is the technologically easy conversion of economic coal to methanol. There are explanations of the problems involved in obtaining fuel methanol as an energy source, as feedstock for the chemical industry, and as a raw material for chemistry. (13 refs.)

Petroleum industry in CIS

International Nuclear Information System (INIS)

Vaillaud, P.

1992-01-01

This paper gives statistical data on petroleum and natural gas industry in USSR and in Eastern Europe: crude oil and gas production, petroleum and natural gas deposits, exports, fuel consumption, pipelines network (total length, compressor or pump stations), petroleum refineries. This paper describes also air pollution (carbon dioxide and sulfur dioxide) and Environmental effects of coal and lignite using in fossil power plants in Eastern Europe. 17 figs., 7 tabs

Shahejie-Shahejie/Guantao/Wumishan and Carboniferous/Permian Coal-Paleozoic Total Petroleum Systems in the Bohaiwan Basin, China (based on geologic studies for the 2000 World Energy Assessment Project of the U.S. Geological Survey)

Science.gov (United States)

Ryder, Robert T.; Qiang, Jin; McCabe, Peter J.; Nuccio, Vito F.; Persits, Felix

2012-01-01

This report discusses the geologic framework and petroleum geology used to assess undiscovered petroleum resources in the Bohaiwan basin province for the 2000 World Energy Assessment Project of the U.S. Geological Survey. The Bohaiwan basin in northeastern China is the largest petroleum-producing region in China. Two total petroleum systems have been identified in the basin. The first, the Shahejie&ndashShahejie/Guantao/Wumishan Total Petroleum System, involves oil and gas generated from mature pods of lacustrine source rock that are associated with six major rift-controlled subbasins. Two assessment units are defined in this total petroleum system: (1) a Tertiary lacustrine assessment unit consisting of sandstone reservoirs interbedded with lacustrine shale source rocks, and (2) a pre-Tertiary buried hills assessment unit consisting of carbonate reservoirs that are overlain unconformably by Tertiary lacustrine shale source rocks. The second total petroleum system identified in the Bohaiwan basin is the Carboniferous/Permian Coal–Paleozoic Total Petroleum System, a hypothetical total petroleum system involving natural gas generated from multiple pods of thermally mature coal beds. Low-permeability Permian sandstones and possibly Carboniferous coal beds are the reservoir rocks. Most of the natural gas is inferred to be trapped in continuous accumulations near the center of the subbasins. This total petroleum system is largely unexplored and has good potential for undiscovered gas accumulations. One assessment unit, coal-sourced gas, is defined in this total petroleum system.

Bitumen performance and chemistry in solvent refined bitumen blends

Science.gov (United States)

Holleran, Glynn; Holleran, Irina; Wilson, Douglas J.

2017-09-01

In years gone past most oil companies in Australia and New Zealand (NZ) developed experts that bridged the divide between refining and paving. This was supported by laboratories in Australia and sometimes Asia. This is no longer the case and many refineries have ceased bitumen production or closed. With the market moving towards imports and control to supply companies disconnects on bitumen passing a national specification and performance on the road. This reduces both durability and increases costs. This has been addressed by development in NZ of a performance specification for hot mix asphalt binders (including modified) and work being done on sealing grades. This paper discusses the development of the HMA specification with respect to crude sources and the development of methodologies to assess imported binders for suitability in all applications including emulsion. The conclusion is that bitumen quality may be maintained by use of these methodologies that include, chromatographic analysis, measurement of thermodynamic internal stability (Heithaus), aging, and Dynamic Shear Rheometry testing and mix performance testing in the laboratory. This forms a regime capable of use in any context and this leads to better durability of surfaces and extended service life.

Refining and end use study of coal liquids

International Nuclear Information System (INIS)

1998-01-01

Two direct coal liquids were evaluated by linear programming analysis to determine their value as petroleum refinery feedstock. The first liquid, DL1, was produced from bitiuminous coal using the Hydrocarbon Technologies, Inc.(HTI) two-stage hydrogenation process in Proof of Concept Run No.1, POC-1. The second liquid, DL2,was produced from sub-bituminous coal using a three-stage HTI process in Proof of Concept Run No. 2, POC-2; the third stage being a severe hydrogenation process. A linear programming (LP) model was developed which simulates a generic 150,000 barrel per day refinery in the Midwest U.S. Data from upgrading tests conducted on the coal liquids and related petroleum fractions in the pilot plant testing phase of the Refining and End Use Study was inputed into the model. The coal liquids were compared against a generic petroleum crude feedstock. under two scenarios. In the first scenario, it was assumed that the refinery capacity and product slate/volumes were fixed. The coal liquids would be used to replace a portion of the generic crude. The LP results showed that the DL1 material had essentially the same value as the generic crude. Due to its higher quality, the DL2 material had a value of approximately 0.60 $/barrel higher than the petroleum crude. In the second scenario, it was assumed that a market opportunity exists to increase production by one-third. This requires a refinery expansion. The feedstock for this scenario could be either 100% petroleum crude or a combination of petroleum crude and the direct coal liquids. Linear programming analysis showed that the capital cost of the refinery expansion was significantly less when coal liquids are utilized. In addition, the pilot plant testing showed that both of the direct coal liquids demonstrated superior catalytic cracking and naphtha reforming yields. Depending on the coal liquid flow rate, the value of the DL1 material was 2.5-4.0 $/barrel greater than the base petroleum crude, while the DL2

Innovative Additive for Bitumen Based on Processed Fats

Science.gov (United States)

Babiak, Michał; Kosno, Jacek; Ratajczak, Maria; Zieliński, Krzysztof

2017-10-01

Various additives, admixtures and modifiers are used to improve technical properties and strength characteristics of building materials. Manufacturers of waterproofing materials, concrete, ceramics and bitumen have to use innovative, increasingly complex and costly additives, admixtures or modifiers. As a result, simple and inexpensive substances have been replaced by complex, long chain polymers, multi component resins or plastics. For economic and ecological reasons waste materials are more frequently used as additives, admixtures and modifiers. Nowadays the most commonly used physical modifiers of bitumen belong to the group of polymers - large molecular organic compounds of natural origin or being the result of planned chemical synthesis. Polymers are substances that do not chemically react with bitumen, they act as fillers or create a spatial network within bitumen (the so called physical cross-linking). The development of organic chemistry has allowed the synthesis of a number of substances chemically modifying bitumen. The most promising are heterocyclic organic compounds belonging to the group of imidazolines. The aim of the study presented in this paper was to demonstrate the suitability of processed natural and post-refining fat waste (diamidoamine dehydrate) as bitumen modifier. This paper discusses the impact of adding technical imidazoline on selected bitumen characteristics. Samples of bitumen 160/220, which is most commonly used for the production of waterproofing products, were analysed. For base bitumen and bitumen modified with technical imidazoline the following measurements were taken: measurement of the softening point by Ball and Ring method, determination of the breaking point by Fraass method and needle penetration measurement at 25°C. Later the samples were aged using TFOT laboratory method and the basic characteristics were determined again. The results showed that a small amount of imidazoline improved bitumen thermoplastic parameters at

The need for a marketing strategy for Alberta bitumen

Energy Technology Data Exchange (ETDEWEB)

Redford, D.A. (Alberta Oil Sands Technology and Research Authority, Edmonton, AB (Canada))

1993-03-01

Over the past 15 years, government and industry have invested heavily in research and development of new technology for extracting bitumen from the Alberta oil sands. The results have been a dramatic increase in the fraction of oil sands deposits that could be economically exploited and a drop in production costs. However, no rapid increase in bitumen recovery has been achieved and most new bitumen production projects have been postponed or cancelled. This is the result of very variable prices for bitumen and the inadequacy of a marketing strategy which relies on the sale of raw bitumen. Options such as transport of bitumen to southern markets are limited by the need to reduce bitumen viscosity for pipelining and by the limited market for emulsified or diluted bitumen. Another possible strategy, conversion of the bitumen to synthetic crude oil, is limited by high costs, product characteristics (too much diesel and not enough gasoline), and a market limited to specialized refineries. A third strategy is to convert and refine bitumen to transportation fuels in Alberta, using inexpensive local natural gas, and transporting the products through existing pipeline facilities. 3 figs.

The need for a marketing strategy for Alberta bitumen

International Nuclear Information System (INIS)

Redford, D.A.

1993-01-01

Over the past 15 years, government and industry have invested heavily in research and development of new technology for extracting bitumen from the Alberta oil sands. The results have been a dramatic increase in the fraction of oil sands deposits that could be economically exploited and a drop in production costs. However, no rapid increase in bitumen recovery has been achieved and most new bitumen production projects have been postponed or cancelled. This is the result of very variable prices for bitumen and the inadequacy of a marketing strategy which relies on the sale of raw bitumen. Options such as transport of bitumen to southern markets are limited by the need to reduce bitumen viscosity for pipelining and by the limited market for emulsified or diluted bitumen. Another possible strategy, conversion of the bitumen to synthetic crude oil, is limited by high costs, product characteristics (too much diesel and not enough gasoline), and a market limited to specialized refineries. A third strategy is to convert and refine bitumen to transportation fuels in Alberta, using inexpensive local natural gas, and transporting the products through existing pipeline facilities. 3 figs

Optical and UV-Aging Properties of LDH-Modified Bitumen

Directory of Open Access Journals (Sweden)

Xing Liu

2015-07-01

Full Text Available Layered double hydroxides (LDHs are an ultraviolet-light (UV resistant material. In this study, LDHs were used to modify bitumen. The optical and UV aging properties of LDHs modified bitumen were investigated. Firstly, the thin films of bitumen, with and without LDHs, were prepared. By using the UV-Vis spectrophotometer, absorbance, reflectance, and transmittance of bituminous thin film were evaluated. The morphology of LDHs-modified bitumen was observed by using fluorescence microscopy (FM. Finally, the aging resistance of LDH-modified bitumen was investigated by using the UV-aging oven. Results indicated that the LDHs, especially with 5 wt % in the bitumen, can effectively absorb and reflect the UV light and improve the UV-aging resistance of bitumen. This implied that the addition of LDHs into bitumen had the potential to prolong the service life of asphalt pavement.

Coal fired steam generation for heavy oil recovery

International Nuclear Information System (INIS)

Firmin, K.

1992-01-01

In Alberta, some 21,000 m 3 /d of heavy oil and bitumen are produced by in-situ recovery methods involving steam injection. The steam generation requirement is met by standardized natural-gas-fired steam generators. While gas is in plentiful supply in Alberta and therefore competitively priced, significant gas price increases could occur in the future. A 1985 study investigating the alternatives to natural gas as a fuel for steam generation concluded that coal was the most economic alternative, as reserves of subbituminous coal are not only abundant in Alberta but also located relatively close to heavy oil and bitumen production areas. The environmental performance of coal is critical to its acceptance as an alternate fuel to natural gas, and proposed steam generator designs which could burn Alberta coal and control emissions satisfactorily are assessed. Considerations for ash removal, sulfur dioxide sorption, nitrogen oxides control, and particulate emission capture are also presented. A multi-stage slagging type of coal-fired combustor has been developed which is suitable for application with oilfield steam generators and is being commissioned for a demonstration project at the Cold Lake deposit. An economic study showed that the use of coal for steam generation in heavy oil in-situ projects in the Peace River and Cold Lake areas would be economic, compared to natural gas, at fuel price projections and design/cost premises for a project timing in the mid-1990s. 7 figs., 3 tabs

Modular-block complex on preparation and processing of oil slurry, spilled and raw petroleum

International Nuclear Information System (INIS)

Pak, V.V.

1999-01-01

The use of non-serial small petroleum equipment for development of remote and low output petroleum deposit, collection and processing of spilled petroleum is urgent issue. Joint-stock company Montazhengineering developed and mastered production of small modular-block complexes for preparation and processing of petroleum. The complex can include the following modules: preparation of raw petroleum for getting commodity petroleum; petroleum processing installation for getting gas, diesel fuel and black oil; installation for refining of nafta; installation for cleaning petroleum products from mercaptans; installation for getting basic oil; installation for getting bitumen and mastic; installation for processing of spilled petroleum and oil slurry. Each of modules can work separately and in various combinations depending on input and necessary assortment of commodity petroleum. One of urgent ecological problem in Kazakhstan petroleum-processing regions is large number barns with spilled petroleum and oil slurry. Their processing will allow to solve the ecological and economical problems. Processing of spilled petroleum and oil slurry in developed installations it's possible to get commodity petroleum and petroleum products

Differences in bitumen and kerogen-bound fatty acid fractions during diagenesis and early catagenesis in a maturity series of New Zealand coals

DEFF Research Database (Denmark)

Glombitza, Clemens; Mangelsdorf, Kai; Horsfield, Brian

2016-01-01

network. Application of the carbon preference index for fatty acids (CPIFA) of bitumen and kerogen-bound acids revealed a linear correlation to the Tmax maturity parameter. This shows that the CPIFA has a clear relation to thermal stability and, thus, reactivity of the buried organic matter....... The difference in slopes of CPIFA vs. Tmax for short and long chain as well as bitumen and kerogen-bound acids may indicate their different degradation susceptibilities. The short chain fatty acids of the bitumen show the highest susceptibility whereas the kerogen-bound long chain fatty acids seem to be most...

Preliminary fingerprinting analysis of Alberta oil sands and related petroleum products

International Nuclear Information System (INIS)

Yang, C.; Wang, Z.D.; Hollebone, B.; Brown, C.E.; Yang, Z.Y.; Landriault, M.; Fieldhouse, B.

2009-01-01

This paper reported on a study that presented a preliminary quantitative chemical characterization of Alberta oil sands and many other related Alberta oils such as oil sand bitumen, Cold Lake bitumen, Albian heavy synthetic crude, and Alberta Mixed sweet blend. The rapid increase in production of the Alberta oil sands has resulted in unprecedented environmental concern. The mining, extraction and production of oil sands such resulted in huge consumption of water resources, huge emission of greenhouse gas and large number of tailings ponds. In addition, accidental spills in the transportation and usage of oil sands will potentially cause considerable impact on the environment. It is therefore essential to have the ability to characterize Alberta oil sands and their oil products. The specific chemical properties of the oil sands bitumen must be known. Therefore, this study collected quantitative data on the concentration and distribution profiles of target compounds in Alberta oil sands and its petroleum products. The chemical fingerprints of 5 Alberta oil sands and their related petroleum products were studied using gas chromatography/flame ionization detection (GC/FID) and gas chromatography/mass spectrometry (GC/MS). The characterized hydrocarbons were n-alkanes; target alkylated PAHs and other EPA priority PAHs; biomarker terpanes and steranes; and bicyclic sesquiterpanes. The information acquired during this study will provide the basis for oil-oil correlation and differentiation in future environmental applications relevant to oil sands. 24 refs., 6 tabs., 4 figs.

Natural analogues of bitumen and bituminized radioactive waste

International Nuclear Information System (INIS)

Hellmuth, K.-H.

1989-07-01

Occurrences of natural bitumen provide possibilities to identify and assess materials, processes, phenomena and conditions in nature which can serve as model cases valid also with respect to a final repository. Natural bitumens meet the basic requirements for use as natural analogues. In natural sites, processes of bitumen formation and degradation often work simultaneously. The major processes are thermal alteration, evaporation, reaction with water, biodegradation, oxidation, weathering and radiation degradation. Progress in analytical organic geochemistry made during recent years has enabled a deeper understanding of the structural and compositional effects of these processes on bitumen. This is necessary in natural analogue applications. The time scales involved in degradation processes, as observed in natural occurrences, exceed the time scales dictated by the half-lives of most important fission products in low and medium level waste by orders of magnitude. Only exposure to the weather at the surface leads to a more rapid destruction of bitumen. Trace metals in bitumen arenot released until the matrix is completely destroyed. Products of radiation degradation and weathering of bitumen are able, to a certain degree, to delay migration of the metal ions released. Impregnation with bitumen may effectively reduce the microbial decomposition of easily destructable organic waste components, as can be deduced on the basis of the excellent preservation of fossils observed in bitumen. The complexity of all the natural sites described requires extensive understanding of the origin and kind of organic material in bitumen, its maturation, migration, alteration and degradation and of the geological and tectonic evolution of the site. The latter is used for establishing the time scale

Changes of Properties of Bitumen Binders by Additives Application

Science.gov (United States)

Remišová, Eva; Holý, Michal

2017-10-01

Requirements for properties of bituminous binders are determined in the European standards. The physico-chemical behaviour of bitumen depends on its colloidal structure (asphaltenes dispersed into an oily matrix constituted by saturates, aromatics and resins) that depends primarily on its crude source and processing. Bitumen properties are evaluated by group composition, elementary analysis, but more often conventional or functional tests. Bitumen for road uses is assessed according to the physical characteristics. For the purpose of improving the qualitative properties of bitumen and asphalts the additives are applied e.g. to increase elasticity, improving the heat stability, improving adhesion to aggregate, to decrease viscosity, increasing the resistance to aging, to prevent binder drainage from the aggregate surface, etc. The objective of presented paper is to assess and compare effect of additives on properties of bitumen binders. In paper, the results of bitumen properties, penetration, softening point, and dynamic viscosity of two paving grade bitumen 35/50, 50/70 and polymer modified bitumen PmB 45/80-75 are analyzed and also the changes of these properties by the application of selected additives (Sasobit, Licomont BS100, Wetfix BE and CWM) to improve adhesion to aggregate and improve workability. Measurements of properties have been performed according to the relevant European standards. The laboratory tests showed significantly increasing the softening point of paving grade bitumen 50/70 and 35/50 by 13 to 45°C. The effect of various additives on bitumen softening point is different. Penetration varies according to type of bitumen and type of used additive. The penetration values of modified bitumen PmB 45/80-75 with additives Sasobit and Licomont BS100 show increase of bitumen stiffness of 16 0.1mm and a shift in the gradation. The changes in penetration and in softening point significantly shown when calculating on Penetration index as a parameter of

New stage of clean coal technology in Japan; Clean coal technology no aratana tenkai ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Kawaguchi, Y [Agency of Natural Resources and Energy, Tokyo (Japan)

1996-09-01

The paper described the positioning and new development of clean coal technology. Coal is an important resource which supplies approximately 30% of the energy consumed in all the world. In the Asian/Pacific region, especially, a share of coal in energy is high, around 60% of the world, and it is indispensable to continue using coal which is abundantly reserved. Japan continues using coal as an important energy among petroleum substituting energies taking consideration of the global environment, and is making efforts for development and promotion of clean coal technology aiming at further reduction of environmental loads. Moreover, in the Asian region where petroleum depends greatly upon outside the region, it is extremely important for stabilization of Japan`s energy supply that coal producing countries in the region promote development/utilization of their coal resources. For this, it is a requirement for Japan to further a coal policy having an outlook of securing stable coal supply/demand in the Asian region. 6 figs., 2 tabs.

Our petroleum challenge : sustainability into the 21. century. 7. ed.

International Nuclear Information System (INIS)

Bott, R.D.; Carson, D.M.; Henderson, J.W.

2004-01-01

The Canadian Centre for Energy Information provides accurate information on all aspects of Canada's energy sector. This report reviews Canada's petroleum resources and the role they play in society. In particular, it discussed the origins of crude oil and natural gas, exploration, production, processing, transportation, refining, marketing and end-use. The report is intended for a diverse audience interested in hydrocarbons, natural gas, crude oil, bitumen, gasoline, petroleum, natural gas liquids, and liquefied natural gas. The report explains the science and technology of the upstream and downstream petroleum industry. Canada's hydrocarbon legacy was described in the first section, followed by exploration, land use, seismic surveys, drilling, and production issues. The challenges and opportunities facing the industry in the twenty-first century were also discussed with reference to sustainable development. Business aspects were also outlined in terms of revenues, public interest, petroleum prices, and employment. refs., tabs., figs

Surface microstructure of bitumen characterized by atomic force microscopy.

Science.gov (United States)

Yu, Xiaokong; Burnham, Nancy A; Tao, Mingjiang

2015-04-01

Bitumen, also called asphalt binder, plays important roles in many industrial applications. It is used as the primary binding agent in asphalt concrete, as a key component in damping systems such as rubber, and as an indispensable additive in paint and ink. Consisting of a large number of hydrocarbons of different sizes and polarities, together with heteroatoms and traces of metals, bitumen displays rich surface microstructures that affect its rheological properties. This paper reviews the current understanding of bitumen's surface microstructures characterized by Atomic Force Microscopy (AFM). Microstructures of bitumen develop to different forms depending on crude oil source, thermal history, and sample preparation method. While some bitumens display surface microstructures with fine domains, flake-like domains, and dendrite structuring, 'bee-structures' with wavy patterns several micrometers in diameter and tens of nanometers in height are commonly seen in other binders. Controversy exists regarding the chemical origin of the 'bee-structures', which has been related to the asphaltene fraction, the metal content, or the crystallizing waxes in bitumen. The rich chemistry of bitumen can result in complicated intermolecular associations such as coprecipitation of wax and metalloporphyrins in asphaltenes. Therefore, it is the molecular interactions among the different chemical components in bitumen, rather than a single chemical fraction, that are responsible for the evolution of bitumen's diverse microstructures, including the 'bee-structures'. Mechanisms such as curvature elasticity and surface wrinkling that explain the rippled structures observed in polymer crystals might be responsible for the formation of 'bee-structures' in bitumen. Despite the progress made on morphological characterization of bitumen using AFM, the fundamental question whether the microstructures observed on bitumen surfaces represent its bulk structure remains to be addressed. In addition

NMR measurement of bitumen at different temperatures.

Science.gov (United States)

Yang, Zheng; Hirasaki, George J

2008-06-01

Heavy oil (bitumen) is characterized by its high viscosity and density, which is a major obstacle to both well logging and recovery. Due to the lost information of T2 relaxation time shorter than echo spacing (TE) and interference of water signal, estimation of heavy oil properties from NMR T2 measurements is usually problematic. In this work, a new method has been developed to overcome the echo spacing restriction of NMR spectrometer during the application to heavy oil (bitumen). A FID measurement supplemented the start of CPMG. Constrained by its initial magnetization (M0) estimated from the FID and assuming log normal distribution for bitumen, the corrected T2 relaxation time of bitumen sample can be obtained from the interpretation of CPMG data. This new method successfully overcomes the TE restriction of the NMR spectrometer and is nearly independent on the TE applied in the measurement. This method was applied to the measurement at elevated temperatures (8-90 degrees C). Due to the significant signal-loss within the dead time of FID, the directly extrapolated M0 of bitumen at relatively lower temperatures (viscosity, the extrapolated M0 of bitumen at over 60 degrees C can be reasonably assumed to be the real value. In this manner, based on the extrapolation at higher temperatures (> or = 60 degrees C), the M0 value of bitumen at lower temperatures (index (HI), fluid content and viscosity were evaluated by using corrected T2.

Selective extraction of natural bitumen

International Nuclear Information System (INIS)

Starshov, M.; Starshov, I.

1991-01-01

The work performed in the field of natural bitumen extraction is aimed at maximum separation of organic phase. On treating bituminous rocks with solvents, the associated metals are extracted together with the organic phase and may further exert a negative effect on refining of natural bitumen. the authors propose a simplified two stage technique for the extraction of bitumen which enables to utilize V and Ni contained in the concentrate of the second stage extraction (Table). At the first stage, negative bitumen is extracted with the summary content of metals not exceeding 0.005%. This allows to avoid de metallization of native bitumen and subject it to treatment by catalytic cracking. during this stage gasoline and kerosene fractions, different oil distillates and condensates can be used as solvents. at the second stage, aromatic and halo id compounds bearing wastes and by-products, i.e. cheap and non deficient reagents, serve as solvents. The technology was tested under laboratory conditions using Tatar bituminous sands. It is also possible to use one solvent only, however, on condition that at first the oil product with the summary metal content below 0.005%, and then the remaining product is extracted. The proposed technology has proved so universal that it can be applied to refining any type of raw material to be found in the territory of the Tatar republic, using surface extraction complexes. (author). 9 refs., tab

Coal liquids -- Who needs them?

International Nuclear Information System (INIS)

Gray, D.; Tomlinson, G.

1995-01-01

The paper discusses the global energy demand situation as presented at the last World Energy Congress. The total energy demand was calculated for each country and projected to 2100. The paper then discusses the energy situation in the United States, especially the forecasted demand for crude oil and natural gas liquids. Imports will be needed to make up the shortfall in domestic production. The shortfall in conventional petroleum could be supplied by converting coal into liquid fuels. Currently the cost of high quality coal liquids is too high to compete with petroleum, but trends suggest that the price will be competitive in the year 2030 using current technology. Continuing research on coal liquefaction will reduce the price of coal liquids so that coal liquids could play a significant role sooner

Upgrading of bitumen using supercritical water

Energy Technology Data Exchange (ETDEWEB)

Kayukawa, T. [JGC Corp., Ibaraki (Japan)

2009-07-01

This presentation outlined the technical and economic aspects of thermal cracking by supercritical water. Supercritical water (SCW) is a commonly used method for upgrading heavy oil to produce pipeline-transportable oil from high-viscous bitumen. The process uses water and does not require hydrogen nor catalysts. Pre-heated bitumen and water enter a vertical reactor with flows of counter current at the supercritical point of water. The upgraded synthetic crude oil (SCO) and pitch are obtained from the top of the reactor when the bitumen is thermally cracked. Bench-scale studies have shown that Canadian oil sands bitumen can be converted to 80 volume per cent of SCO and 20 volume per cent of pitch. The SCO has satisfied Canadian pipeline specifications in terms of API gravity and kinetic viscosity. The kinetic viscosity of the pitch has also satisfied boiler fuel specifications. tabs., figs.

Oil and gas processing products to obtain polymers modified bitumen

Directory of Open Access Journals (Sweden)

Serhiy Pyshyev

2017-07-01

Full Text Available To obtain modified bitumen with excellent adhesive properties, coumarone-indene resin (CIR was used. However, bitumens modified by CIR have somewhat worse plastic properties. For the improvement of the plastic properties of road bitumen modified by coumarone-indene resin, the paper proposes to use plasticizers. Characterized by a high content of rings (aromatic-naphthenic oils, a range of compounds was used as plasticizers. Of all different plasticizers tested, the tar produced from West-Ukrainian oils has been found to be the most effective one. The optimal ratio between modified bitumen components was determined enabling to obtain the commercial product of polymers modified bitumen of BMP 60/90-52 brand. The complex thermogravimetry and differential-thermal analysis has been used to analyze the initial and modified bitumen. Bitumens modified by CIR have shown by far the highest thermal stability under operation conditions. Keywords: Bitumen, Modifier, Coumarone-indene resin, Plasticizer

Markets for Canadian bitumen-based feedstock

International Nuclear Information System (INIS)

Marshall, R.; Lauerman, V.; Yamaguchi, N.

2001-02-01

This study was undertaken in an effort to determine the market potential for crude bitumen and derivative products from the Western Canadian Sedimentary Basin in 2007. As part of the study, CERI assessed the economic viability of a wide range of bitumen-based feedstock based on their refining values, investigated the sensitivity of refinery demand to the prices of these feedstocks, and examined the competitiveness of bitumen-based feedstocks and conventional crudes. A US$18.00 per barrel price for West Texas Intermediate at Cushing, Oklahoma, was assumed in all calculations, including other crude prices, as well as for Western Canadian and US crude oil production forecasts. Four different scenarios have been considered, but only the 'most plausible' scenario is discussed in the report. Consequently, Hydrocracked/Aromatics Saturated Synthetic Crude Oil, which is currently only a hypothetical product, is excluded from consideration. The availability of historical price differentials for the various competing crudes was another assumption used in developing the scenario. Proxy prices for the bitumen-based feedstock were based on their respective supply costs. The study concludes that the principal dilemma facing bitumen producers in Western Canada is to determine the amount of upgrading necessary to ensure an economic market for their product in the future. In general, the greater the degree of upgrading, the higher is the demand for bitumen-based feedstock. However, it must be kept in mind that the upgrading decisions of other bitumen producers, along with many other factors, will have a decisive impact on the economics of any individual project. The combination of coking capacity and asphalt demand limits the market for heavy and extra-heavy crudes. As a result, the researchers concluded that major expansion of heavy crude conversion capacity may have to wait until the end of the current decade. The economic market for bitumen-based blends in 2007 is estimated at

Composition, peat-forming vegetation and kerogen paraffinicity of Cenozoic coals: Relationship to variations in the petroleum generation potential (Hydrogen Index)

Energy Technology Data Exchange (ETDEWEB)

Petersen, H.I.; Lindstroem, S.; Nytoft, H.P.; Rosenberg, P. [Geological Survey of Denmark and Greenland (GEUS), Oester Voldgade 10, DK-1350 Copenhagen (Denmark)

2009-04-01

Coals with similar thermal maturity and from the same deposit normally show a considerable range in petroleum generation potential as measured by the Hydrogen Index (HI). This variation may partly be related to variations in plant input to the precursor mires and organic matter preservation. It is widely accepted that some Cenozoic coals and coaly sediments have the potential to generate oil, which is related to the coal's paraffinicity. Coal paraffinicity is not readily reflected in the bulk HI. In this paper, the relationships between measured HI and coal composition, coal kerogen paraffinicity and floral input have been investigated in detail for three sets of coals from Colombia/Venezuela, Indonesia, and Vietnam. The samples in each coal set are largely of iso-rank. The petroleum generation potential was determined by Rock-Eval pyrolysis. Reflected light microscopy was used to analyse the organic matter (maceral) composition and the thermal maturity was determined by vitrinite reflectance (VR) measurements. The botanical affinity of pollen and spores was analysed by palynology. Coal kerogen paraffinicity was determined by ruthenium tetroxide-catalysed oxidation (RTCO) followed by chain length analysis and quantification (mg/g TOC) of the liberated aliphatic chains. The coals are dominated by huminite, in particular detrohuminite. Only the Vietnamese coals are rich in microscopically visible liptinite. The pollen and spores suggest that the coals were derived principally from complex angiosperm mire vegetations, with subordinate proportions of ferns that generally grew in a subtropical to tropical climate. Measured HI values vary considerably, but for the majority of the coals the values lie between approximately 200 mg HC/g TOC and 300 mg HC/g TOC. Aliphatics yielding monocarboxylic acids dominate in the coal kerogen, whereas aliphatics yielding dicarboxylic acids are secondary. However, the dicarboxylic acids show that cross-linking long-chain aliphatics

The after petroleum. When the wells dried up

International Nuclear Information System (INIS)

Lefevre-Balleydier, A.

2006-01-01

Facing the petroleum crisis of the years 70 and the today petroleum reserves problems, the author wonders on a society without cheap petroleum. Which energies will take over: gas, coal, nuclear of renewable energies? In seven chapters the following topics are discussed: the petroleum in our life, for how long, the alternative energies, the environmental impacts, the socio-economic impacts, the possible actions today. (A.L.B.)

Determination of organic products resulting of chemical and radiochemical decompositions of bitumen. Applications to embedded bitumens

International Nuclear Information System (INIS)

Walczak, I.

2000-01-01

Bitumen can be used for embedding most of wastes because of its high impermeability and its relatively low reactivity with of chemicals. Bituminization is one of selected solutions in agreement with nuclear safety, waste compatibility and economic criteria. Bitumen, during storage, undergoes an auto-irradiation due to embedded radio-elements. During this stage,drums are not airtight then oxygen is present. In disposal configuration, water, which is a potential vector of radioactivity and organic matter, is an other hazard factor liable to deteriorate the containment characteristics of bitumen wastes. The generation of water-soluble organic complexing agents can affect the integrity of the wasteform due to an increase of the radionuclides solubility. The first aim of this work is the quantitative and qualitative characterisation of soluble organic matter in bitumen leachates. Different leaching solutions were tested (various pH, ionic strength, ratio S/V). When the pH of the leaching solutions increases, the total organic carbon released increases as well. Identified molecules are aromatics like naphthalene, oxidised compounds like alcohols, linear carbonyls, aromatics, glycols and nitrogen compounds. For the cement equilibrated solution (pH 13.5), the effect of ionic strength becomes significative and influences the release of soluble organic matter. This soluble organic matter can be bio-degraded if microorganisms can growth. The second aim of this work is to study the effect of radio-oxidative ageing on the bitumen confinement properties. During radio-oxidation, the chemical properties of bitumen are modified. The μ-IRTF analysis shows the formation of hydroxyl compounds and aromatic acids. The formation of these polar groups does not influence in our study the water uptake. However the organic matter release increases significantly with the irradiation dose. (author)

Biosurfactants: Promising Molecules for Petroleum Biotechnology Advances

Directory of Open Access Journals (Sweden)

DARNE GERMANO DE ALMEIDA

2016-10-01

Full Text Available The growing global demand for sustainable technologies that improves the efficiency of petrochemical processes in the oil industry has driven advances in petroleum biotechnology in recent years. Petroleum industry uses substantial amounts of petrochemical-based synthetic surfactants in its activities as mobilizing agents to increase the availability or recovery of hydrocarbons as well as many other applications related to extraction, treatment, cleaning and transportation. However, biosurfactants have several potential applications for use across the oil processing chain and in the formulations of petrochemical products such as emulsifying/demulsifying agents, anticorrosive, biocides for sulphate-reducing bacteria, fuel formulation, extraction of bitumen from tar sands and many other innovative applications. Due to their versatility and proven efficiency, biosurfactants are often presented as valuable versatile tools that can transform and modernise petroleum biotechnology in an attempt to provide a true picture of state of the art and directions or use in the oil industry. We believe that biosurfactants are going to have a significant role in many future applications in the oil industries and in this review therefore, we highlight recent important relevant applications, patents disclosures and potential future applications for biosurfactants in petroleum and related industries.

Biosurfactants: Promising Molecules for Petroleum Biotechnology Advances.

Science.gov (United States)

De Almeida, Darne G; Soares Da Silva, Rita de Cássia F; Luna, Juliana M; Rufino, Raquel D; Santos, Valdemir A; Banat, Ibrahim M; Sarubbo, Leonie A

2016-01-01

The growing global demand for sustainable technologies that improves the efficiency of petrochemical processes in the oil industry has driven advances in petroleum biotechnology in recent years. Petroleum industry uses substantial amounts of petrochemical-based synthetic surfactants in its activities as mobilizing agents to increase the availability or recovery of hydrocarbons as well as many other applications related to extraction, treatment, cleaning, and transportation. However, biosurfactants have several potential applications for use across the oil processing chain and in the formulations of petrochemical products such as emulsifying/demulsifying agents, anticorrosive, biocides for sulfate-reducing bacteria, fuel formulation, extraction of bitumen from tar sands, and many other innovative applications. Due to their versatility and proven efficiency, biosurfactants are often presented as valuable versatile tools that can transform and modernize petroleum biotechnology in an attempt to provide a true picture of state of the art and directions or use in the oil industry. We believe that biosurfactants are going to have a significant role in many future applications in the oil industries and in this review therefore, we highlight recent important relevant applications, patents disclosures and potential future applications for biosurfactants in petroleum and related industries.

Biosurfactants: Promising Molecules for Petroleum Biotechnology Advances

Science.gov (United States)

De Almeida, Darne G.; Soares Da Silva, Rita de Cássia F.; Luna, Juliana M.; Rufino, Raquel D.; Santos, Valdemir A.; Banat, Ibrahim M.; Sarubbo, Leonie A.

2016-01-01

The growing global demand for sustainable technologies that improves the efficiency of petrochemical processes in the oil industry has driven advances in petroleum biotechnology in recent years. Petroleum industry uses substantial amounts of petrochemical-based synthetic surfactants in its activities as mobilizing agents to increase the availability or recovery of hydrocarbons as well as many other applications related to extraction, treatment, cleaning, and transportation. However, biosurfactants have several potential applications for use across the oil processing chain and in the formulations of petrochemical products such as emulsifying/demulsifying agents, anticorrosive, biocides for sulfate-reducing bacteria, fuel formulation, extraction of bitumen from tar sands, and many other innovative applications. Due to their versatility and proven efficiency, biosurfactants are often presented as valuable versatile tools that can transform and modernize petroleum biotechnology in an attempt to provide a true picture of state of the art and directions or use in the oil industry. We believe that biosurfactants are going to have a significant role in many future applications in the oil industries and in this review therefore, we highlight recent important relevant applications, patents disclosures and potential future applications for biosurfactants in petroleum and related industries. PMID:27843439

Evaluating Re-Os systematics in organic-rich sedimentary rocks in response to petroleum generation using hydrous pyrolysis experiments

Science.gov (United States)

Rooney, A.D.; Selby, D.; Lewan, M.D.; Lillis, P.G.; Houzay, J.-P.

2012-01-01

Successful application of the 187Re–187Os geochronometer has enabled the determination of accurate and precise depositional ages for organic-rich sedimentary rocks (ORS) as well as establishing timing constraints of petroleum generation. However, we do not fully understand the systematics and transfer behaviour of Re and Os between ORS and petroleum products (e.g., bitumen and oil). To more fully understand the behaviour of Re–Os systematics in both source rocks and petroleum products we apply hydrous pyrolysis to two immature hydrocarbon source rocks: the Permian Phosphoria Formation (TOC = 17.4%; Type II-S kerogen) and the Jurassic Staffin Formation (TOC = 2.5%; Type III kerogen). The laboratory-based hydrous pyrolysis experiments were carried out for 72 h at 250, 300, 325 and 350 °C. These experiments provided us with whole rock, extracted rock and bitumen and in some cases expelled oil and asphaltene for evaluation of Re–Os isotopic and elemental abundance. The data from these experiments demonstrate that the majority (>95%) of Re and Os are housed within extracted rock and that thermal maturation does not result in significant transfer of Re or Os from the extracted rock into organic phases. Based on existing thermodynamic data our findings suggest that organic chelating sites have a greater affinity for the quadravalent states of Re and Os than sulphides. Across the temperature range of the hydrous pyrolysis experiments both whole rock and extracted rock 187Re/188Os ratios show small variations (3.3% and 4.7%, for Staffin, respectively and 6.3% and 4.9% for Phosphoria, respectively). Similarly, the 187Os/188Os ratios show only minor variations for the Staffin and Phosphoria whole rock and extracted rock samples (0.6% and 1.4% and 1.3% and 2.2%). These isotopic data strongly suggest that crude oil generation through hydrous pyrolysis experiments does not disturb the Re–Os systematics in ORS as supported by various studies on natural systems. The

Rheological properties of crumb rubber modified bitumen containing antioxidant

International Nuclear Information System (INIS)

Mohamed, A. A; Omar, Husaini; Hamzah, M.O; Ismail, H.

2009-01-01

Rheology has become a useful tool in the characterization of the bitumen performance on the pavement. Visco-elastic properties of crumb rubber modified bitumen with antioxidants (CR30) were determined by the means of rheological measurement. This measurement led to a better knowledge of bitumen behavior that occurs when subjected to different thermal and mechanical conditions, as seen during road construction and services in the field. Dynamic Shear Rheometer (DSR) was used to characterize the rheology of the binders before and after oven aging. The binders were aged for 3 and 9 days. Results of a compatibility test showed that the addition of CR30 modified bitumen is compatible with the base bitumen. The results of unaged samples indicated that the addition of 1% CR30 and 5% CR30 modified binders caused an increase in G value as a result of the rheological changes. Results showed that aging has significant influence on bitumen rheology, by increasing complex modulus and decreasing phase angle. (author)

Bitumen pressure cell installation and monitoring procedure: Draft

International Nuclear Information System (INIS)

1987-02-01

A 6-in. (150-mm)-thick bitumen layer will be placed between the upper shaft preliminary concrete lining and the steel lining component of the final lining. The function of this layer is twofold; first, it will act as a compliant sealing layer which, because of the bitumen's fluid properties, will remain effective even if the concrete and steel lining components suffer significant strains; and second, it will help to ensure a uniform transmission of rock or hydrostatic loads to the inner lining components. A type 200--300 penetration grade bitumen (ASTM D946) will be used, with 32% by weight of added limestone flour. The purpose of the limestone flour is to ensure that the bitumen has a density which is greater than that of the formation fluids, resulting in a positive pressure gradient from the bitumen to the ground water. The resulting mixture will have a specific gravity of about 1.25 at 60/degree/F (15/degree/C). Pressure measurements in the bitumen layer are needed in order to determine loads on the inner lining components. Although some initial loading will occur in response to excavation, full rock and hydrostatic loads will not develop until post-construction thawing of the freeze wall is complete. Loads transmitted by the bitumen layer to the other lining components will be those which act radially, i.e., the bitustatic pressure, or the radial stress if deviatoric stresses develop

Greenhouse gas implications of using coal for transportation: Life cycle assessment of coal-to-liquids, plug-in hybrids, and hydrogen pathways

International Nuclear Information System (INIS)

Jaramillo, Paulina; Samaras, Constantine; Wakeley, Heather; Meisterling, Kyle

2009-01-01

Using coal to produce transportation fuels could improve the energy security of the United States by replacing some of the demand for imported petroleum. Because of concerns regarding climate change and the high greenhouse gas (GHG) emissions associated with conventional coal use, policies to encourage pathways that utilize coal for transportation should seek to reduce GHGs compared to petroleum fuels. This paper compares the GHG emissions of coal-to-liquid (CTL) fuels to the emissions of plug-in hybrid electric vehicles (PHEV) powered with coal-based electricity, and to the emissions of a fuel cell vehicle (FCV) that uses coal-based hydrogen. A life cycle approach is used to account for fuel cycle and use-phase emissions, as well as vehicle cycle and battery manufacturing emissions. This analysis allows policymakers to better identify benefits or disadvantages of an energy future that includes coal as a transportation fuel. We find that PHEVs could reduce vehicle life cycle GHG emissions by up to about one-half when coal with carbon capture and sequestration is used to generate the electricity used by the vehicles. On the other hand, CTL fuels and coal-based hydrogen would likely lead to significantly increased emissions compared to PHEVs and conventional vehicles using petroleum-based fuels.

Aquatic toxicity of petroleum products and dispersant agents determined under the U.S. EPA Oil Spill Research Program

Science.gov (United States)

The U.S. EPA Office of Research and Development has developed baseline data on the ecotoxicity of selected petroleum products and several chemical dispersants as part of its oil spills research program. Two diluted bitumens (dilbits) from the Alberta Tar Sands were tested for acu...

Optimisation of bitumen emulsion properties for ballast stabilisation

International Nuclear Information System (INIS)

D’Angelo, G.; Lo Presti, D.; Thom, N.

2017-01-01

Ballasted track, while providing economical and practical advantages, is associated with high costs and material consumption due to frequent maintenance. More sustainable alternatives to conventional ballasted trackbeds should therefore aim at extending its durability, particularly considering ongoing increases in traffic speed and loads. In this regard, the authors have investigated a solution consisting of bitumen stabilised ballast (BSB), designed to be used for new trackbeds as well as in reinforcing existing ones. This study presents the idea behind the technology and then focuses on a specific part of its development: the optimisation of bitumen emulsion properties and dosage in relation to ballast field conditions. Results showed that overall bitumen stabilisation improved ballast resistance to permanent deformation by enhancing stiffness and damping properties. Scenarios with higher dosage of bitumen emulsion, higher viscosity, quicker setting behaviour, and harder base bitumen seem to represent the most desirable conditions to achieve enhanced in-field performance. [es

Preparation of fuels and chemical products from mixtures of coal and petroleum

Energy Technology Data Exchange (ETDEWEB)

Krichko, A A; Yulin, M K

1973-01-01

The distillate to 320/sup 0/C from the liquid phase hydrogenation of a 1 : 1 coal-Arlan petroleum mixture was processed to yield phenols 3.4 percent, high aromatics gasoline 81.2 percent, C/sub 1/--C/sub 4/ alkanes 13.5 percent, H/sub 2/S 0.5 percent, and water 1.0 percent. Thus, C/sub 6/--C/sub 8/ phenols were separated from the fraction distilling to 240/sup 0/C, and the phenol-free fraction and the 240 to 320/sup 0/C fraction were hydrofined over an aluminum-cobalt-molybdenum catalyst at 400/sup 0/C and 50 atm. Distillation gave a gasoline fraction, which was reformed, and a 180 to 320/sup 0/C fraction, which was hydrocracked at 380/sup 0/C and 40 atm on a zeolite catalyst.

Achievement report for fiscal 1997 on research under New Sunshine Program. Research on heavy oil hydrogenation and heavy oil/coal coprocessing; 1997 nendo jushitsuyu no suisoka shori narabi ni jushitsuyu/sekitan no coprocessing ni kansuru kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-02-01

The achievements of the Hokkaido National Industrial Research Institute relating to the titled research are reported. In the study relating to the structural properties of heavy oils, the structures of products of Green River shale oil carbonization is analyzed, heterofunctional groups contained in the oil are subjected to FT-IR (Fourier transform infrared) spectroscopic analysis, and their forms of existence are investigated. In the study relating to the hydrogenation process of heavy oils, findings obtained from experiments are reported, which involve the processing of shale oil by hydrogenation and changes brought about in its chemical structure, hydrogenation of oil sand bitumen, kinetics of hydrocracking of bitumen at a high conversion rate, and a lumping model for bitumen hydrocracking reaction. In the study relating to the coprocessing of heavy oil/coal, coprocessing is experimented for coal and shale oil, coal and oil sand bitumen, and other combinations, and the results are reported. Also, a review is made of the transfer of hydrogen in coprocessing. (NEDO)

Naphtha interaction with bitumen and clays : a preliminary study

Energy Technology Data Exchange (ETDEWEB)

Afara, M.; Munoz, V.; Mikula, R. [Natural Resources Canada, Devon, AB (Canada). CANMET Western Research Centre

2010-07-01

This PowerPoint presentation described a preliminary study conducted to characterize naphtha interactions with bitumen and clays. Coarse tailings, fluid-fine tailings, and froth treatment tailings are produced as a result of surface mine oil sands operations. Solvents are used to produce the bitumens, but the actual fraction of the solvent that evaporates and contributes to VOCs from tailing ponds is poorly understood. This study examined the interactions between the solvent, bitumen and mineral components in froth treatment tails. The study was conducted with aim of quantifying the VOC or solvent escaping from the froth treatment tailings. Samples containing bitumen, clay, a bitumen-clay mixture, or MFT were spiked with 3000 ppm of solvent. The amount of naphtha released was monitored by gas chromatography, mass spectrometry, and flame ionization detection of the evolved gases. The results were expressed as a percentage of the total hydrocarbon peak area of the sample versus a control. Results of the study showed that the naphtha interacted more strongly with the bitumen than with kaolinite and the clay minerals from the oil sands. Although initial solvent evaporation was reduced in the presence of bitumens and clays, long-term solvent releases will need to be quantified. tabs., figs.

Fuel options for oil sands

International Nuclear Information System (INIS)

Wise, T.

2005-01-01

This presentation examined fuel options in relation to oil sands production. Options include steam and hydrogen (H 2 ) for upgrading; natural gas by pipeline; bitumen; petroleum coke; and coal. Various cost drivers were also considered for each of the fuel options. It was noted that natural gas has high energy value but the capital cost is low, and that coke's energy value is very low but the capital cost is high. A chart forecasting energy prices was presented. The disposition of Western Canada's northern gas situation was presented. Issues concerning rail transportation for coal were considered. Environmental concerns were also examined. A chart of typical gas requirements for 75,000 B/D oil sands projects was presented. Issues concerning steam generation with gas and mining cogeneration with gas fuel and steam turbines were discussed, as well as cogeneration and H 2 with gas fuels and steam turbines. Various technology and fuel utility options were examined, along with details of equipment and processes. Boiler technologies were reviewed by type as well as fuel and steam quality and pressure. Charts of cogeneration with gas turbine and circulation fluid bed boilers were presented. Gasification processes were reviewed and a supply cost basis was examined. Cost drivers were ranked according to energy, operating considerations and capital investment. Results indicated that fuel costs were significant for gas and coal. Capital costs and capital recovery charge was most significant with coal and gasification technology. Without capital recovery, cash costs favour the use of bitumen and coke. Gasification would need lower capital and lower capital recovery to compete with direct burning. It was concluded that direct burning of bitumen can compete with natural gas. With price volatility anticipated, dual fuel capability for bitumen and gas has merit. Petroleum coke can be produced or retrieved from stockpiles. Utility supply costs of direct burning of coke is

Distilling coal, etc

Energy Technology Data Exchange (ETDEWEB)

Nelson, J

1917-12-21

Coals of various kinds such as shales, bitumens, and oil sand, peat, etc. are distilled at 350 to 450/sup 0/C and in the presence of vapors and gases obtained by cracking hydrocarbon oils, or the gases obtained by separating the condensable hydrocarbons therefrom, and, if desired, with the addition of superheated steam. The hydrocarbons are properly cracked by passing through molten lead as described in Specification 116,304. According to the Provisional Specification, superheated steam alone may be used to effect the distillation.

Rheological testing of crumb rubber modified bitumen

CSIR Research Space (South Africa)

Mturi, GAJ

2011-08-01

Full Text Available used to analyse crumb rubber modified (CRM) bitumen is that the specified gap setting in the configuration of the DSR between the upper and lower test platens is too small to accommodate crumb rubber particles. DSR testing of CRM bitumen therefore...

Self lubrication of bitumen froth in pipelines

International Nuclear Information System (INIS)

Joseph, D.D.

1997-01-01

In this paper I will review the main properties of water lubricated pipelines and explain some new features which have emerged from studies of self-lubrication of Syncrudes' bitumen froth. When heavy oils are lubricated with water, the water and oil are continuously injected into a pipeline and the water is stable when in a lubricating sheath around the oil core. In the case of bitumen froth obtained from the Alberta tar sands, the water is dispersed in the bitumen and it is liberated at the wall under shear; water injection is not necessary because the froth is self-lubricating

Technology of new generation of manufacture of liquid products from coal

Directory of Open Access Journals (Sweden)

Zhaksyntay Kairbekov

2012-04-01

Full Text Available In the given work the review about a condition of research and trial works on technology perfection hydrogenation coals is made. Done design work on processing 65 thousand tons / year Karazhyra coal to liquid fuels and other products of combustion purposes. The basic advantage of the Kazakhstan technology for producing motor fuels coal hydrogenation at low pressure hydrogen (up to 5 MPa compared to the processes developed in the USA, Germany, Japan, Great Britain, and Russia. An integrated low-waste technology and coal processing, which allows the production of industrially important: liquid and patent fuel, binders for briquetting, and allocate bitumen due to the utilization of sludge.

Reactivity of North Bohemian coals in coprocessing of coal/oil mixtures

Energy Technology Data Exchange (ETDEWEB)

Sebor, G.; Cerny, J.; Maxa, D.; Blazek, J. [Inst. of Chemical Technology, Prague (Czechoslovakia); Sykorova, I. [Inst. of Rock Structure and Mechanics, Prague (Czechoslovakia)

1995-12-01

Autoclave experiments with North Bohemian coal were done in order to evaluate their reactivity in coprocessing with petroleum vacuum residue, Selected coals were comprehensively characterized by using a number of analytical methods. While the coals were of similar geological origin, some of their characteristics differed largely from one coal to another. Despite the differences in physical and chemical structure, the coals provided very similar yields of desired reaction products. The yields of a heavy non- distillable fraction and/or an insoluble solid residue were, under experimental conditions, largely affected by retrogressive reactions (coking). The insoluble solid fractions were examined microscopically under polarized light.

Markets for Canadian bitumen-based feedstock

International Nuclear Information System (INIS)

Lauerman, V.

2001-01-01

The best types of refineries for processing western Canadian bitumen-based feedstock (BBF) were identified and a potential market for these feedstock for year 2007 was calculated. In addition, this power point presentation provided an estimation of potential regional and total demand for BBF. BBF included Athabasca bitumen blend, de-asphalted blend, coked sour crude oil (SCO), coked sweet SCO, hydrocracked SCO and hydrocracked/aromatic saturated SCO (HAS). Refinery prototypes included light and mixed prototypes for primary cracking units, light and heavy prototypes for primary coking units, as well as no coking, coking severe and residuum prototypes for primary hydrocracking units. The presentation included graphs depicting the natural market for Western Canadian crudes as well as U.S. crude oil production forecasts by PADD districts. It was forecasted that the market for bitumen-based feedstock in 2007 will be tight and that the potential demand for bitumen-based blends would be similar to expected production. It was also forecasted that the potential demand for SCO is not as promising relative to the expected production, unless price discounting or HAS will be available. 11 figs

Dynamics and structure of water-bitumen mixtures

DEFF Research Database (Denmark)

Lemarchand, Claire; Greenfield, Michael L.; Hansen, Jesper Schmidt

2016-01-01

Systems of Cooee bitumen and water up to 4% mass are studied by molecular dynamics simulations. The cohesive energy density of the system is shown to decrease with an increasing water content. This decrease is due mainly to an increase in the interaction energy which is not high enough to counter......Systems of Cooee bitumen and water up to 4% mass are studied by molecular dynamics simulations. The cohesive energy density of the system is shown to decrease with an increasing water content. This decrease is due mainly to an increase in the interaction energy which is not high enough...... droplets being more stable at the highest temperature simulated. The droplet is mainly located close to the saturates molecules in bitumen. Finally, it is shown that the water dynamics is much slower in bitumen than in pure water because it is governed by the diffusion of the droplet and not of the single...

Hydrocarbons and oxygen compounds in the bitumens of kukersite oil shales

Energy Technology Data Exchange (ETDEWEB)

Pais, R; Klesment, I; Pobul, L

1979-01-01

This is a continuation of an earlier work which described commercial batches of kukersite in terms of oxidative kerogen destruction. The low concentration of bitumen in the kerogen and its group composition indicate that this bitumen is syngenetic. The authors studied the way in which the bitumen and kerogen are structurally connected. They also analyzed four commercial batches of kukersite and asphaltite, the organic-rich dark-colored layer found in the middle of the kukersite strate. Whereas American studies of Colorado shales containing 10-20% bitumen from organic matter have indicated, based on the identical structures of the bitumen and kerogen that there is a genetic relationship between them, the present study rarely found such structural elements in the bitumen and kerogen. The kukersite contained little bitumen--0.7% of the total organic matter. The authors believed that the different composition of the bitumen and kerogen does not prove that they are epigenetic. Kukersite also fails to follow the rule that the paraffins of ancient shales have KHapprox.1 and carbon chains shorter than C/sub 22/.

PRODUCTION OF CARBON PRODUCTS USING A COAL EXTRACTION PROCESS

Energy Technology Data Exchange (ETDEWEB)

Dady Dadyburjor; Philip R. Biedler; Chong Chen; L. Mitchell Clendenin; Manoj Katakdaunde; Elliot B. Kennel; Nathan D. King; Liviu Magean; Peter G. Stansberry; Alfred H. Stiller; John W. Zondlo

2004-08-31

This Department of Energy National Energy Technology Laboratory sponsored project developed carbon products, using mildly hydrogenated solvents to extract the organic portion of coal to create synthetic pitches, cokes, carbon foam and carbon fibers. The focus of this effort was on development of lower cost solvents, milder hydrogenation conditions and improved yield in order to enable practical production of these products. This technology is needed because of the long-term decline in production of domestic feedstocks such as petroleum pitch and coal tar pitch. Currently, carbon products represents a market of roughly 5 million tons domestically, and 19 million tons worldwide. Carbon products are mainly derived from feedstocks such as petroleum pitch and coal tar pitch. The domestic supply of petroleum pitch is declining because of the rising price of liquid fuels, which has caused US refineries to maximize liquid fuel production. As a consequence, the long term trend has a decline in production of petroleum pitch over the past 20 years. The production of coal tar pitch, as in the case of petroleum pitch, has likewise declined significantly over the past two decades. Coal tar pitch is a byproduct of metallurgical grade coke (metcoke) production. In this industry, modern metcoke facilities are recycling coal tar as fuel in order to enhance energy efficiency and minimize environmental emissions. Metcoke production itself is dependent upon the production requirements for domestic steel. Hence, several metcoke ovens have been decommissioned over the past two decades and have not been replaced. As a consequence sources of coal tar are being taken off line and are not being replaced. The long-term trend is a reduction in coal tar pitch production. Thus import of feedstocks, mainly from Eastern Europe and China, is on the rise despite the relatively large transportation cost. To reverse this trend, a new process for producing carbon products is needed. The process must be

Assessment of Physicochemical Properties of some Bitumens from ...

African Journals Online (AJOL)

natural bitumen resources and potentials for sustained production of bitumen in large quantity, but basic ... Ondo State, and a manufactured type from Kaduna Refining and Petrochemical ..... Policies and Practices in Pavement Design and.

Coal-oil coprocessing at HTI - development and improvement of the technology

Energy Technology Data Exchange (ETDEWEB)

Stalzer, R.H.; Lee, L.K.; Hu, J.; Comolli, A. [Hydrocarbon Technologies, Inc., Lawrenceville, NJ (United States)

1995-12-31

Co-Processing refers to the combined processing of coal and petroleum-derived heavy oil feedstocks. The coal feedstocks used are those typically utilized in direct coal liquefaction: bituminous, subbituminous, and lignites. Petroleum-derived oil, is typically a petroleum residuum, containing at least 70 W% material boiling above 525{degrees}C. The combined coal and oil feedstocks are processed simultaneously with the dual objective of liquefying the coal and upgrading the petroleum-derived residuum to lower boiling (<525{degrees}C) premium products. HTI`s investigation of the Co-Processing technology has included work performed in laboratory, bench and PDU scale operations. The concept of co-processing technology is quite simple and a natural outgrowth of the work done with direct coal liquefaction. A 36 month program to evaluate new process concepts in coal-oil coprocessing at the bench-scale was begun in September 1994 and runs until September 1997. Included in this continuous bench-scale program are provisions to examine new improvements in areas such as: interstage product separation, feedstock concentrations (coal/oil), improved supported/dispersed catalysts, optimization of reactor temperature sequencing, and in-line hydrotreating. This does not preclude other ideas from DOE contracts and other sources that can lead to improved product quality and economics. This research work has led to important findings which significantly increased liquid yields, improved product quality, and improved process economics.

Application of organic petrography in North American shale petroleum systems: A review

Science.gov (United States)

Hackley, Paul C.; Cardott, Brian J.

2016-01-01

Organic petrography via incident light microscopy has broad application to shale petroleum systems, including delineation of thermal maturity windows and determination of organo-facies. Incident light microscopy allows practitioners the ability to identify various types of organic components and demonstrates that solid bitumen is the dominant organic matter occurring in shale plays of peak oil and gas window thermal maturity, whereas oil-prone Type I/II kerogens have converted to hydrocarbons and are not present. High magnification SEM observation of an interconnected organic porosity occurring in the solid bitumen of thermally mature shale reservoirs has enabled major advances in our understanding of hydrocarbon migration and storage in shale, but suffers from inability to confirm the type of organic matter present. Herein we review organic petrography applications in the North American shale plays through discussion of incident light photographic examples. In the first part of the manuscript we provide basic practical information on the measurement of organic reflectance and outline fluorescence microscopy and other petrographic approaches to the determination of thermal maturity. In the second half of the paper we discuss applications of organic petrography and SEM in all of the major shale petroleum systems in North America including tight oil plays such as the Bakken, Eagle Ford and Niobrara, and shale gas and condensate plays including the Barnett, Duvernay, Haynesville-Bossier, Marcellus, Utica, and Woodford, among others. Our review suggests systematic research employing correlative high resolution imaging techniques and in situ geochemical probing is needed to better document hydrocarbon storage, migration and wettability properties of solid bitumen at the pressure and temperature conditions of shale reservoirs.

Fly ashes from coal and petroleum coke combustion: current and innovative potential applications.

Science.gov (United States)

González, Aixa; Navia, Rodrigo; Moreno, Natalia

2009-12-01

Coal fly ashes (CFA) are generated in large amounts worldwide. Current combustion technologies allow the burning of fuels with high sulfur content such as petroleum coke, generating non-CFA, such as petroleum coke fly ash (PCFA), mainly from fluidized bed combustion processes. The disposal of CFA and PCFA fly ashes can have severe impacts in the environment such as a potential groundwater contamination by the leaching of heavy metals and/or particulate matter emissions; making it necessary to treat or reuse them. At present CFA are utilized in several applications fields such as cement and concrete production, agriculture and soil stabilization. However, their reuse is restricted by the quality parameters of the end-product or requirements defined by the production process. Therefore, secondary material markets can use a limited amount of CFA, which implies the necessity of new markets for the unused CFA. Some potential future utilization options reviewed herein are zeolite synthesis and valuable metals extraction. In comparison to CFA, PCFA are characterized by a high Ca content, suggesting a possible use as neutralizers of acid wastewaters from mining operations, opening a new potential application area for PCFA that could solve contamination problems in emergent and mining countries such as Chile. However, this potential application may be limited by PCFA heavy metals leaching, mainly V and Ni, which are present in PCFA in high concentrations.

Coal, gas, petroleum, assets and weaknesses: up to when?; Charbon, gaz, petrole, atouts et faiblesses: jusqu'a quand?

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-05-01

The meeting on the perenniality of the coal, the gas and the petroleum, organized the 24 april 2003 at Bordeaux, took place around four topics: what about the fossil fuels reserves, how to conciliate the greenhouse effect, the air pollution and the energy consumption, the future energies as the carbon dioxide catchment and the hydrogen use, the fossil energies future in function of their use. The document presents the whole interventions and the opening allocution. (A.L.B.)

Biodegradation of hydrocarbon compounds in Agbabu natural bitumen

African Journals Online (AJOL)

Infrared spectral changes and gravimetric analysis from the preliminary biodegradability study carried out on Agbabu Natural Bitumen showed the vulnerability of the bitumen to some bacteria: Pseudomonas putrefaciens, Pseudomonas nigrificans, Bacillus licheniformis, Pseudomonas fragi and Achromobacter aerogenes.

Estimation of bitumen and clay content in fine tailings

International Nuclear Information System (INIS)

Motta Cabrera, S.C.; Bryan, J.; Kantzas, A.

2007-01-01

Fine tailings are the components of tailings ponds and the by-product of the oil sand extraction process, consisting mostly of water with small amounts of bitumen, sand, silts and clays. Because of the large volumes of tailings, an important environmental and production process issue involves the reduction of the remaining bitumen in the tailings stream. This paper presented the results of a study that used low field nuclear magnetic resonance (NMR) in order to estimate the bitumen, clay and water content of synthetic tailings samples. NMR is a non-destructive technique that is utilized to determine compositions of oil and brine emulsions and the viscosity of heavy oil and bitumen as well as in reservoir characterization, measuring properties such as permeability, porosity, mobile and immobile fluids, and fluid saturations. The study prepared and tested numerous samples with variable water, bitumen, sand and clay concentrations in the NMR tool under ambient conditions. Two qualities of water and bitumen were used to prepare the synthetic samples. Each type of water and bitumen was analyzed as a single substance and in a mixture with the typical solids found in tailings composition. These included kaolinite, illite, sodium montmorillonite and sand. These synthetic samples were analyzed using different mixing configurations, as a function of time and in two different NMR tools. It was concluded that NMR is a potential application for on-line determination of tailings streams composition. 18 refs., 3 tabs., 17 figs

Briquetting and coking behavior of Bobov-Dol coal

Energy Technology Data Exchange (ETDEWEB)

Naundorf, W.

1987-01-01

Hard Bulgarian glance brown coal (23.2% ash content, 16% coal moisture 2.39% sulfur) was studied for its general suitability for partial black coal coke substitution in coking plants and for the possibility of producing pyrolysis briquets for coking purposes. Laboratory briquetting variants include coal briquetting without binders, with sulfite lye as binder, briquetting after partial demineralization by wet classification, briquetting of different screening fractions (0 to 4 mm), briquetting as a mixture with type 35 caking black coal as well as mixed with type 34 less caking black coal under addition of black coal tar, pitch or bitumen. Coking of the briquets produced was carried at with and without charge compacting. Graphs and tables provide briquetting and coking results. It is concluded that high strength coke can be produced from this brown coal, but it can only be used commercially as heating coke due to its high ash and sulfur content. Briquetting and coking of partially demineralized brown coal in a mixture with black coal and binders resulted in suitable metallurgical coke. Maximum percentage of brown coal in the briquetting mixture was 30%. 4 refs.

Chemical and fuel products from mixtures of coal and petroleum

Energy Technology Data Exchange (ETDEWEB)

Krichko, A A; Yulin, M K

1973-01-01

From a 1:1 coal-petroleum low-pressure (less than 100 atm) hydrogenation product, C/sub 6-8/ phenols comprising 7.4 percent of the product distilling below 240/sup 0/C were extracted with 10 percent aqueous caustic soda and hydrofined at 325/sup 0/C and 20 atm on cobalt molybdenum alumina catalyst. The combined 240/sup 0/ to 320/sup 0/C and less than or equal to 240/sup 0/C neutral fractions were hydrofined at 400/sup 0/C and 50 atm on cobalt molybdenum alumina catalyst, and the gasoline comprising 42.8 percent of the catalyzate hydroreformed at 490/sup 0/C and 50 atm to raise the octane number from 50.4 to 81.8 to 91.3 and increase the aromatics content from 9.0 to 55.6 percent. Gasoline of 78.5 to 90.5 octane number was prepared by hydrocracking the 180 to 320/sup 0/C catalyzate fraction at 380/sup 0/C and 40 atm on a molybdenum hydrogen sodium yttrium zeolite catalyst greatly favoring C/sub 3-4/ hydrocarbons in the gaseous products (9.0 percent).

The development of polyurethane modified bitumen emulsions for cold mix applications

OpenAIRE

Carrera Páez, Virginia; Cuadri Vega, Antonio Abad; García Morales, Moisés; Partal López, Pedro

2015-01-01

Bitumen emulsions stand for an alternative paving practice to the traditional hot-mix asphalts. In addition, modified bitumen emulsions show a better performance than unmodified ones. This work studies the feasibility of obtaining polyurethane modified bitumen emulsions, in which an isocyanate-functionalized polyol constitutes the bitumen modifier (in varying concentration from 1 to 4 wt.%). Storage stability and high in-service performance are evaluated by means of evolution of droplet size ...

Leaching studies on ion exchange resins immobilized in bitumen matrix

International Nuclear Information System (INIS)

Grosche Filho, C.E.; Chandra, U.; Villalobos, J.P.

1986-01-01

Many samples of bitumen mixed with ion exchange resin labelled with 134 Cs were prepared to study radionuclide leaching from bitumen waste forms. The resins used in tests were nuclear grade mixed cationic/aniocic bead resins. Different bitumen types were assayed: two distilled and two oxidized bitumens. Leached fractions were collected accordingly to the recommendation of ISO method, with complete exchange of leachant after each sampling. The volume collected for analysis was one liter. Marinelli beckers were used to improve counting efficiency in a Ge(Li) detector. The diffusion coefficients for samples prepared with distilled and oxidized bitumens were obtained. Mathematical models of transport phenomena applied to cylindrical geometry was employed to fit experimental data aiming to explain leaching mechanism and predict the long time behavior of immobilized radionuclides. (M.C.K.) [pt

Routine Testing of Bitumen Binders

Science.gov (United States)

Holý, Michal; Remišová, Eva

2017-12-01

The quality of bituminous binders used in the construction and maintenance of road surfaces is currently assessed by empirical testing based on obtaining one value for specific boundary conditions, which were designed about 100 years ago. Basic empirical tests include the softening point and penetration, but the practice shows that these tests appear to be inadequate. The evaluation of changes of bitumen properties during the production and paving process of bituminous mixture is also important. The paper points out how the "traditional" tests as softening point and penetration and viscosity are sufficient to evaluate properties of bitumen binders.

Effects of Waste Plastic on the Physical and Rheological Properties of Bitumen

Science.gov (United States)

Ezree Abdullah, Mohd; Asyiqin Ahmad, Nurul; Putra Jaya, Ramadhansyah; Hassan, Norhidayah Abdul; Yaacob, Haryati; Rosli Hainin, Mohd

2017-05-01

Plastic disposal is one of the major problems for developing countries like Malaysia, at the same time Malaysia needs a large network of roads for its smooth economic and social development. The limited source of bitumen needs a deep thinking to ensure fast road construction. Therefore, the use of plastic waste in road construction not only can help to protect environment but also able to help the road construction industry. The aims of this research are to study the effects of waste plastic on rheological properties of bitumen. Modified bitumen was prepared by using blending techniques. Bitumen was heated and plastic waste was slowly added. Rheological properties of bitumen were performance by penetration, softening point, viscosity and direct shear rheometer test. The results showed that when content of plastic waste increase, the penetration value, softening point and viscosity of bitumen also increase. Generally, plastic waste improves the performance of bitumen when it was added into bitumen. It can be said that the usage helps to improve the performance of the road pavement which also reduces the rutting effect.

Molecular weight distribution of Athabasca bitumen

Energy Technology Data Exchange (ETDEWEB)

Champagne, P J; Manolakis, E; Ternan, M

1985-03-01

A sample of whole Athabasca bitumen has been fractionated by preparative g.p.c. The weights of the fractions have been determined and their molecular weights measured by several methods. In contras to previously published data, consistent results were obtained using different solvents (THF, benzene/water) and using different techniques (v.p.o., f.p.d. and g.c.-m.s.). This has resulted in a accurate definition of the molecular weight distribution of Athabasca bitumen.

Scrubbing King Coal's dirty face : a new gasification project southeast of Edmonton hopes to make coal cleaner now and for future generations

Energy Technology Data Exchange (ETDEWEB)

Collison, M.

2008-01-15

This article described the proposed Dodds-Roundhill Coal Gasification Project. This first commercial coal gasification plant in Canada will be developed by Edmonton-based Sherritt International Corporation, in a 50/50 partnership with the Ontario Teachers' Pension Plan. The project will include a surface coal mine and a coal gasification facility located approximately 80 km southeast of Edmonton, Alberta. Coal gasification is emerging as a clean alternative for converting coal into energy products. It involves the gasification process which breaks down coal to produce hydrogen, carbon monoxide and carbon dioxide, collectively known as synthesis gas (syngas). The syngas can then be used for fuel, as a petrochemical feedstock, or it can be further processed into hydrogen for use by bitumen upgraders and crude oil refineries in Alberta. Carbon dioxide, which is highly concentrated are relatively easy to capture will be either sequestered or used in enhanced oil recovery. Construction will begin in mid-2009 following project application and an environmental impact assessment. 3 figs.

Rheological modification of bitumens with new poly-functionalized furfural analogs

Energy Technology Data Exchange (ETDEWEB)

Alejandro Martinez; Antonio Paez; Nazario Martin [Universidad Complutense, Madrid (Spain). Departamento de Quimica Organica

2008-06-15

The rheological properties of bitumens modified with different aldehydes show that furfural is a very efficient reagent. An optimization of the reaction conditions involving concentration, acid catalyst, reaction time and temperature has been performed. In order to determine the influence of the furan ring and the formyl groups on the reactivity of bitumens, a series of new organic molecules as chemical reagents bearing up to six furan rings and four formyl groups, have been reacted with a B 80/100 bitumen. The results indicate a remarkably better performance than furfural, leading to harder modified bitumens. 31 refs., 3 figs., 5 tabs.

Irradiation tests on bitumen and bitumen coated materials; Essais d'irradiation de bitume et d'enrobes bitumineux

Energy Technology Data Exchange (ETDEWEB)

Tabardel-Brian, R.; Rodier, J.; Lefillatre, G. [Commissariat a l' Energie Atomique, Chusclan (France). Centre de Production de Plutonium de Marcoule

1969-07-01

The use of bitumen as a material for coating high-activity products calls for prior study of the resistance of bitumen to irradiation. After giving briefly the methods of preparation of bitumen- coated products, this report lists the equipment which has been used for carrying out the {beta} and {gamma} irradiations of these products, and gives the analytical results obtained as a function of the dose rates chosen and of the total integrated dose. Finally, some conclusions have been drawn concerning the best types of bitumen. It should be stressed that some bitumens apparently underwent no degradation whatsoever nor any volume increase, for a total integrated dose of 1.8 x 10{sup 10} rads. (authors) [French] Dans le cadre de l'enrobage par le bitume des produits de haute activite, il est necessaire de verifier au prealable, la tenue du bitume a l'irradiation. Apres un bref rappel de la preparation des enrobes bitumineux, le present rapport regroupe les moyens qui ont ete mis en oeuvre, pour effectuer leurs irradiations sous rayonnement {beta} et sous rayonnement {gamma}, ainsi que les resultats des analyses qui ont ete faites en fonction des debits de doses choisis et de la dose totale integree. Enfin, des conclusions ont ete tirees sur les types de bitume a retenir. On peut souligner que certains bitumes n'ont subi aucune degradation apparente ni augmentation de volume pour une dose totale integree de 1.8 x 10{sup 10} rads. (auteurs)

THE IMPROVEMENT OF TECHNOLOGY PRODUCTION OF BITUMEN FOR THE ROAD PAVING

Directory of Open Access Journals (Sweden)

N. A. Belova

2016-01-01

Full Text Available Aim. The oil (artificial bitumens, got by conversion of the oil cheese, are broadly used in the road construction. The track record of the development road covering, studies, bound with improvement their characteristic and development of the competitions among technology is presented in this article.Methods. Nowdays the modern developments in the field of production bitumen road marks are implemented using such technological-go acceptance as chemical actuated heavy oil cheese, which principles are based on regulation of the energybetween molecular interactions and optimization their dimensionality, allowing raise quality bitumen.Results. Adjusting the depth of recovery of the oxidized product, it is possible to obtain different composition, plasticity and heat resistance of the bitumen. The residual bitumen obtained by two-stage oxidation with subsequent vacuum distillation of the oxidized product comply with GOST 60/90. Vacuum gas oil in the production of residual bitumen corresponds to the motor fuel for marine installations.Conclusion. Today, the bitumen production leaves on positions packed-valuable segment oil processing industry. The Main customer roads - a state. Herewith important role as ideologues of the development of the culture road construction plays the Federal road agency, supporting developing competition amongst leading technology. Introduction new technology at conversion remaining component oils, founded on do active cheese to account physical and chemical of the influence, with using the modern equipment, including equipment, using subject to influence effects, ultrasonic and electro-magnetic fields, and others, allows to get the qualitative road bitumens from majority of the oils, scanned earlier unfit for production bitumen.

Non-Newtonian behavior and molecular structure of Cooee bitumen under shear flow

DEFF Research Database (Denmark)

Lemarchand, Claire; Bailey, Nicholas; Daivis, Peter

2015-01-01

The rheology and molecular structure of a model bitumen (Cooee bitumen) under shear are investigated in the non-Newtonian regime using non-equilibrium molecular dynamics simulations. The shear viscosity, normal stress differences, and pressure of the bitumen mixture are computed at different shear...... rates and different temperatures. The model bitumen is shown to be a shear-thinning fluid at all temperatures. In addition, the Cooee model is able to reproduce experimental results showing the formation of nanoaggregates composed of stacks of flat aromatic molecules in bitumen. These nanoaggregates...

Strategic human resources study of the upstream petroleum industry : the decade ahead

International Nuclear Information System (INIS)

2003-10-01

This report presents the results of a 10 month study of the human resources issues in Canada's upstream petroleum industry. The study identifies workforce demographics, skills, and supply and demand. It also discusses the impact of technology and other key challenges facing human resources issues. The upstream petroleum industry includes exploration and production, service industries, pipeline transmission, natural gas processing, and heavy oil and bitumen extracting and upgrading. The study defined four regions in Canada: Western Canada Sedimentary Basin, the oil sands, the north, and the east coast. The main influences on the management practices within the upstream petroleum industry are: globalization; cyclical economic conditions; operational excellence business models; government regulatory requirements; stakeholder expectations for involvement; technological advances; changing demographics, and workplace skills. The study also presented suggestions for changes in best practices to improve the efficiency and effectiveness of product and service delivery. refs., tabs., figs

Demand outlook for sulfur and high-sulfur petroleum coke

Energy Technology Data Exchange (ETDEWEB)

Koshkarov, V.Ya.; Danil' yan, P.G.; Feotov, V.E.; Gimaev, R.N.; Koshkarova, M.E.; Sadykova, S.R.; Vodovichenko, N.S.

1980-01-01

The feasibility of using sulfur and high-sulfur petroleum coke fines in pyrometallurgical processes and also in the chemical and coal-tar chemical industry is examined. Results of industrial tests on briquetting fines of petroleum coke with a petroleum binder are presented. The feasibility of using the obtained briquets in shaft furnace smelting of oxidized nickel ores, production of anode stock, and also in the chemical industry are demonstrated.

Assessment of Physicochemical Properties of some Bitumens from ...

African Journals Online (AJOL)

Assessment of the results vis-a-vis available information on bitumens elsewhere indicate that any clear surface or underground natural bitumen obtainable in the region of Agbabu village in Ondo State, and a manufactured type from Kaduna Refining and Petrochemical Company (KRPC) in the country are comparable with ...

Hydrothermal Petroleum in Active Continental Rift: Lake Chapala, Western Mexico, Initial Results.

Science.gov (United States)

Zarate-del Valle, P. F.; Simoneit, B. R.; Ramirez-Sanchez, H. U.

2003-12-01

Lake Chapala in western Mexico is located partially in the Citala Rift, which belongs to the well-known neotectonic Jalisco continental triple junction. The region is characterized by active volcanism (Ceboruco, Volcan de Fuego), tectonic (1995 earthquake, M=8, 40-50 mm to SW) and hydrothermal (San Juan Cosala & Villa Corona spas and La Calera sinter deposit) activities. Hydrothermal petroleum has been described in active continental rift (East African Rift) and marine spreading zones (Guaymas Basin, Gulf of California). In 1868 the Mexican local press reported that manifestations of bitumen were appearing in front of the Columba Cap on the mid south shore of Lake Chapala. This bitumen is linked to the lake bottom and when the water level decreases sufficiently it is possible to access these tar bodies as islands. Because of these manifestations the Mexican oil company (PEMEX) drilled an exploration well (2,348m) at Tizapan El Alto without success. Hydrothermal activity is evident in the tar island zone as three in-shore thermal springs (26.8 m depth, 48.5° C, pH 7.8 and oriented N-S). The preliminary analyses by GC-MS of the tar from these islands indicate hydrothermal petroleum derived from lake sedimentary organic matter, generated at low temperatures (150° -200° C). The tars contain no n-alkanes, no PAH or other aromatics, but a major UCM of branched and cyclic hydrocarbons and mature biomarkers derived from lacustrine biota. The biomarkers consist of mainly 17α (H),21β (H)-hopanes ranging from C27 to C34 (no C28), gammacerane, tricyclic terpanes (C20-C26), carotane and its cracking products, and drimanes (C14-C16). The biomarker composition indicates an organic matter source from bacteria and algae, typical of lacustrine ecosystems. 14C dating of samples from two tar islands yielded ages exceeding 40 kyrs, i.e., old carbon from hydrothermal/tectonic remobilization of bitumen from deeper horizons to the surface. The occurrence of hydrothermal petroleum in

On indicators of genetic relation between uranium-bearing bitumen with oil-like substances

International Nuclear Information System (INIS)

Pen'kov, V.F.

1980-01-01

Mineralogical indicators are considered which confirm that uranium-bearing (containing pitchblende) solid carbon substrates in the process of their formation had a stage of liquid-viscous state, and were sedimented in a close association with solid oil bitumens. The following cases are studied: 1) in concentrated macroextracts of uranium-bearing bitumens fine relicts of coloured oreless bitumens, less oxidated and carbonizated, are found sporadically in the passing light; 2) indicators of the development of black uranium-bearing bitumen along separate extracts or joint agregates of kerito- and asphalt-like substrates are observed in passing light within the veinlets of solid bitumens being in carbonate rocks; 3) linses of solid bitumens of fragmentary rock have zone structure according to the observation in passing light. The direct relation between black uranium-bearing bitumens and solid hydrocarbons which can form out of oil-like substances. Initial substances for them were defferent; resinous bitumens in the first case, kerito- and asphalt-like substances - in the second one, and paraffin substances - in the third one. It shows the nonselective character of the formation out of them of black uranium-bearing bitumens due to the processes of oxidation and carbonization [ru

Assessment of the petroleum, coal and geothermal resources of the economic community of West African States (ECOWAS) Region

Energy Technology Data Exchange (ETDEWEB)

Mattick, Robert E. [U.S. Geological Survey, Boulder, CO (United States); Spencer, Frank D. [U.S. Geological Survey, Boulder, CO (United States); Zihlman, Frederick N. [U.S. Geological Survey, Boulder, CO (United States)

1982-01-01

Approximately 85 percent of the land area of the ECOWAS (Economic Community of West African States) region is covered by basement rocks (igneous and highly metamorphosed rocks) or relatively thin layers of Paleozoic, Upper Precambrian, and Continental Intercalaire sedimentary rocks. These areas have little or no petroleum potential. The ECOWAS region can be divided into 13 sedimentary basins on the basis of analysis of the geologic framework of Africa. These 13 basins can be further grouped into 8 categories on the basis of similarities in stratigraphy, geologic history, and probable hydrocarbon potential. The author has attempted to summarize the petroleum potential within the geologic framework of the region. The coal discoveries can be summarized as follows: the Carboniferous section in the Niger Basin; the Paleocene-Maestrichtian, Maestrichtian, and Eocene sections in the Niger Delta and Benin; the Maestrichtian section in the Senegal Basin; and the Pleistocene section in Sierra Leone. The only proved commercial deposits are the Paleocene-Maestrichtian and Maestrichtian subbituminous coal beds of the Niger Delta. Some of the lignite deposits of the Niger Delta and Senegal Basin, however, may be exploitable in the future. Published literature contains limited data on heat-flow values in the ECOWAS region. It is inferred, however, from the few values available and the regional geology that the development of geothermal resources, in general, would be uneconomical. Exceptions may include a geopressured zone in the Niger Delta and areas of recent tectonic activity in the Benue Trough and Cameroon. Development of the latter areas under present economic conditions is not feasible.

Bitumen modified with recycled polyurethane foam for employment in hot mix asphalt

Directory of Open Access Journals (Sweden)

Miguel Ángel Salas

2018-01-01

Full Text Available A wide variety of modifiers have been applied to bitumen in order to enhance their properties and performance. Among them, polymers have been mainly used. The aim of this paper is to assess the use of polyurethane foam waste as a bitumen modifier for hot mix asphalts. The polyurethane foam is a by-product of the manufacturing of polyurethane for thermal insulation. From a bitumen with a penetration grade of 50/70, various samples with percentages of waste material in weight ranging from 1% to 5% were produced and tested. Samples with 5% of waste material or more became rough and were refused due to their poor workability. A bituminous mixture with modified bitumen with a 4% of polyurethane was manufactured and compared with a sample with the same aggregates and original bitumen. Results in Marshall test showed that a mix with polymer modified bitumen yielded improvements in stability and a lower deformability. This result suggests that the employment of polyurethane foam waste is a promising bitumen modifier, contributing also to recycle waste materials.

The future of coal-fired generation

Energy Technology Data Exchange (ETDEWEB)

White, G. [Sherritt International Corp., Calgary, AB (Canada)

2004-07-01

The 3 features that will ensure coal's place as a primary energy source are its affordability, availability and its abundance. Coal reserves represent more than 200 years of supply. Graphs depicting coal consumption in North America, Central and South America, Western Europe, Easter Europe, Middle East, Africa, and Asia show that coal use is expected to grow 1.5 per cent annually. Asia is the greatest consumer of coal, while the consumption of coal in Eastern Europe is steadily declining. About half of the electricity supply in the United States will continue to be generated by coal and non-electrical utilization is also expected to grow. Emerging technologies that are promoting efficiency of coal utilization include combustion technology, clean coal technology, conversion technology and emissions technology. These technologies also address environmental concerns regarding coal combustion, such as removal of carbon dioxide through sequestration and reduction in nitrogen oxides, sulphur dioxide and particulates. Mercury mitigation technologies are also being developed. It was noted that the use of coal is mitigated by other available supply such as nuclear, natural gas and hydro which provide the base load generation. Renewable energy supply can meet up to 20 per cent of the base load, while coal can fill be gap between base load and peak loads. It was noted that the use of coal in direct industrial processes allows for synergies such as syngas for bitumen upgrading, coal as a chemical feedstock with electricity as a by-product, combined heat and power and cogeneration. tabs., figs.

Relation Between Bitumen Content and Percentage Air Voids in Semi Dense Bituminous Concrete

Science.gov (United States)

Panda, R. P.; Das, Sudhanshu Sekhar; Sahoo, P. K.

2018-06-01

Hot mix asphalt (HMA) is a heterogeneous mix of aggregate, mineral filler, bitumen, additives and air voids. Researchers have indicated that the durability of the HMA is sensitive on the actual bitumen content and percentage air void. This paper aims at establishing the relationship between the bitumen content and the percentage air voids in Semi Dense Bituminous Concrete (SDBC) using Viscosity Grade-30 (VG-30) bitumen. Total 54 samples have been collected, for formulation and validation of relationship and observed that the percentage air voids increases with decrease in actual bitumen content and vice versa. A minor increase in percentage air voids beyond practice of designed air voids in Marshall Method of design is required for better performance, indicating a need for reducing the codal provision of minimum bitumen content for SDBC as specified in Specification for Road & Bridges (Fourth Revision) published by Indian Road Congress, 2001. The study shows a possibility of reducing designed minimum bitumen content from codal provision for SDBC by 0.2% of weight with VG-30 grade of Bitumen.

Relation Between Bitumen Content and Percentage Air Voids in Semi Dense Bituminous Concrete

Science.gov (United States)

Panda, R. P.; Das, Sudhanshu Sekhar; Sahoo, P. K.

2018-02-01

Hot mix asphalt (HMA) is a heterogeneous mix of aggregate, mineral filler, bitumen, additives and air voids. Researchers have indicated that the durability of the HMA is sensitive on the actual bitumen content and percentage air void. This paper aims at establishing the relationship between the bitumen content and the percentage air voids in Semi Dense Bituminous Concrete (SDBC) using Viscosity Grade-30 (VG-30) bitumen. Total 54 samples have been collected, for formulation and validation of relationship and observed that the percentage air voids increases with decrease in actual bitumen content and vice versa. A minor increase in percentage air voids beyond practice of designed air voids in Marshall Method of design is required for better performance, indicating a need for reducing the codal provision of minimum bitumen content for SDBC as specified in Specification for Road & Bridges (Fourth Revision) published by Indian Road Congress, 2001. The study shows a possibility of reducing designed minimum bitumen content from codal provision for SDBC by 0.2% of weight with VG-30 grade of Bitumen.

Characterization of solid residues from coal liquefaction processes. Phase I

Energy Technology Data Exchange (ETDEWEB)

Potter, J.; McDougall, W.M.; Kybett, B.D.; Neufeld, C.

1981-01-01

Various coal liquefaction and beneficiation processes are being investigated by independent research groups sponsored by the Canadian Federal Government. These processes include the co-processing of heavy oils and bitumen with coal, oxygen removal and hydrogenation of coal and supercritical gas extraction of coal. The end products, gaseous and liquid fuels and insoluble organic residues, vary with the experimental conditions. The physical properties and origin of the insoluble residue may influence such factors as degree of conversion, efficiency of the process, and ultimately, gaseous and liquid yields. One of the most suitable methods of assessing the nature of the insoluble residues is the use of petrography. This report deals with petrographic assessment of the coals and residues from various coal conversion processes; attempts were made to characterize the solid phases in the residues; to assess them in a quantitative manner and where possible; to correlate the results with experimental data; and to assess their effects on conversion. (30 refs.)

Hydrogenate bitumen, says Canmet

Energy Technology Data Exchange (ETDEWEB)

Pruden, B B; Denis, J M

1977-06-01

The refining of Canada's heavy oils and in particular oil sand bitumens is complicated by the presence of mineral matter (clay and salt), chemically bound nickel, vanadium, iron, sulfur, and nitrogen. Upgrading is necessary before conventional refining because of the high pitch content of the bitumens. The Canada Centre for Mineral and Energy Technology (CANMET), of the Department of Energy. Mines and Resources, has developed a thermal hydrocracking process which concentrates all of the metals and mineral matter in a small pitch fraction and produces a high yield of low viscosity distillate for subsequent catalytic hydrorefining. Scientists at CANMET also have been working on the development of catalysts for an alternative direct catalytic hydrocracking process. Hydrocracking processes, when compared to the coking processes now employed or envisaged by industry for the next 5 yr, have several advantages which are listed.

Supercritical solvent extraction of oil sand bitumen

Science.gov (United States)

Imanbayev, Ye. I.; Ongarbayev, Ye. K.; Tileuberdi, Ye.; Mansurov, Z. A.; Golovko, A. K.; Rudyk, S.

2017-08-01

The supercritical solvent extraction of bitumen from oil sand studied with organic solvents. The experiments were performed in autoclave reactor at temperature above 255 °C and pressure 29 atm with stirring for 6 h. The reaction resulted in the formation of coke products with mineral part of oil sands. The remaining products separated into SARA fractions. The properties of the obtained products were studied. The supercritical solvent extraction significantly upgraded extracted natural bitumen.

Probing Trace-elements in Bitumen by Neutron Activation Analysis

NARCIS (Netherlands)

Nahar, S.N.; Schmets, A.J.M.; Scarpas, Athanasios

Trace elements and their concentrations play an important role in both chemical and physical properties of bitumen. Instrumental Neutron Activation Analysis (INAA) has been applied to determine the concentration of trace elements in bitumen. This method requires irradiation of the material with

Investigation on the effects of gamma irradiation on bitumen

International Nuclear Information System (INIS)

Mello, M.S.; Braz, D.; Motta, L.M.G.

2011-01-01

Brazil has more than 218,000 km of asphalt-paved highways. Bitumen is a generic term for natural or manufactured black or dark-colored solid, semisolid, or viscous cementitious materials that are composed mainly of high molecular weight hydrocarbons (90-95%). Several papers have shown that the irradiation process has changed the mechanical behavior in some polymers. This work aims to analyze the behavior of Brazilian irradiated Bitumen (CAP 50-70). In order to provide a preliminary evaluation, bitumen samples and cylindrical specimens of asphaltic mixture were tested. The bitumen samples were irradiated 0.1 to 300 kGy, and asphaltic mixture specimen was irradiated 5 to 300 kGy. The cylindrical asphaltic mixture specimen of 10.16 cm diameter used in this study was molded using an asphalt-aggregate mixture. The specimens were irradiated in LIN/UFRJ/Brazil using a Gamma cell Co 60 source of gamma irradiation with an applied dose rate of 29.7 Gy/min. After irradiated, the bitumen samples were subjected to penetration test and the asphaltic mixtures were subjected to indirect tensile strength test (diametral compression) for determination of the resilient modulus, according to ASTM method D 4123. The results of these experiments for each dose were compared with the control (nonirradiated). As expected, the penetration results showed that the ratio (irradiated/non-irradiated) decreases with increasing of irradiation dose for bitumen samples and the resilient modulus results showed that the ratio (irradiated/non-irradiated) increases with increasing of irradiation dose for asphaltic mixture. (author)

Promotive study on preparation of basis for foreign coal import. Study on coal renaissance

Energy Technology Data Exchange (ETDEWEB)

Muraoka, Yoji [Japan Economic Research Institute, Tokyo

1988-09-16

This is an interim report on the coal renaissance study carried out in 1987 as a part of the Promotive Study on Preparation of Basis for Foreign Coal Import. The background and ideology of coal renaissance, future aspect of demand for coal, problems pertaining to the expansion of application, and a proposal for the expansion of coal usage are described in order. The role of coal expected as an alternate fuel for petroleum, development of new application fields for coal, conversion to coal, contribution of Japan to the stablization of international coal supply are outlined. Coal renaissance aims, based on technology, at stimulation of coal demand, change in the image of coal, and the utilization of the accumulated abundant knowhow. The aspect of coal demand in 2000, solution and current status of various restricting factors relating to the use of coal in general industry, and the remaining problems are discussed. 6 figures, 10 tables.

The extraction of bitumen from western tar sands. Annual report, July 1990--July 1991

Energy Technology Data Exchange (ETDEWEB)

Oblad, A.G.; Bunger, J.W.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1992-04-01

Contents of this report include the following: executive summary; characterization of the native bitumen from the Whiterocks oil sand deposit; influence of carboxylic acid content on bitumen viscosity; water based oil sand separation technology; extraction of bitumen from western oil sands by an energy-efficient thermal method; large- diameter fluidized bed reactor studies; rotary kiln pyrolysis of oil sand; catalytic upgrading of bitumen and bitumen derived liquids; ebullieted bed hydrotreating and hydrocracking; super critical fluid extraction; bitumen upgrading; 232 references; Appendix A--Whiterocks tar sand deposit bibliography; Appendix B--Asphalt Ridge tar sand deposit bibliography; and Appendix C--University of Utah tar sands bibliography.

REFINERY INTEGRATION OF BY-PRODUCTS FROM COAL-DERIVED JET FUELS

Energy Technology Data Exchange (ETDEWEB)

Leslie R. Rudnick; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2005-05-18

This report summarizes the accomplishments toward project goals during the first six months of the second year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts, acquisition and installation of a research gasoline engine, and modification of diesel engines for use in evaluating diesel produced in the project. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Coal samples have procured and are being assessed for cleaning prior to use in coking studies.

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Leslie R. Rudnick; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2005-11-17

This report summarizes the accomplishments toward project goals during the first six months of the second year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts, acquisition and installation of a research gasoline engine, and modification of diesel engines for use in evaluating diesel produced in the project. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Evaluations to assess the quality of coal based fuel oil are reported. Coal samples have procured and are being assessed for cleaning prior to use in coking studies.

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Leslie R. Rudnick; Andre Boehman; Chunshan Song; Bruce Miller; John Andresen

2004-09-17

This report summarizes the accomplishments toward project goals during the first twelve months of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts, acquisition and installation of a research gasoline engine, and modification of diesel engines for use in evaluating diesel produced in the project. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Coal samples have procured and are being assessed for cleaning prior to use in coking studies.

Use of advanced chemical fingerprinting in PAH source identification and allocation at a coal tar processing site

International Nuclear Information System (INIS)

Brown, J.S.; Boehm, P.D.; Douglas, G.S.

1995-01-01

Advanced chemical fingerprinting analyses were used to determine source allocation at a former coal tar processing facility which had been converted to a petroleum recycling site. Soil samples from the site had high petroleum hydrocarbon concentrations and elevated levels of polynuclear aromatic hydrocarbons (PAH). Comparisons of PAH distributions were used to differentiate the coal tar hydrocarbons from the petroleum hydrocarbons in soil samples. A more specific technique was needed to accurately allocate the contribution of the two sources to the observed PAH contamination in the soil. Petroleum biomarkers (steranes and triterpanes) which are present in crude oils and many refined petroleum products but are absent in coal tar were used to quantitatively allocate the source of the PAH contamination based on the relative ratio of the PAH to the biomarkers in soil samples. Using the resulting coal tar/petroleum source ratio the contribution of petroleum to the overall PAH contamination at the site was calculated. A multivariate statistical technique (principal component analysis or PCA) was used to provide an independent validation of the source allocation. The results of the source allocation provided a foundation for the site clean-up and remediation costs

Bitumen still seen as potential anchor on crude prices

International Nuclear Information System (INIS)

Jaremko, G.

2001-01-01

Researchers at the Canadian Energy Research Institute have released a 225-page technical report on downstream oil-refining markets entitled 'Markets for Canadian bitumen-based feedstock'. The report claims that 22 of 27 refineries that buy western Canadian production are not planning to improve their ability to process heavy grades of oil any time soon. Instead, investments will focus on complying with environmental requirements for reformulated refined products, particularly to eliminate sulphur impurities in gasoline and diesel fuel. Another focus will be to upgrade raw bitumen output into synthetic crude. It was shown that over the next 7 years, Canadian and U.S. oil markets have the potential to increase growth in bitumen production from 244,000 barrels per day (bpd) to 555,000 bpd. The potential for additional, upgraded synthetic crude oil is even greater, from 450,000 bpd to 806,000 bpd. Increasing the output of synthetic crude oil is considered to be an effective way to reduce North America's reliance on imported oil. Untreated, discount-priced bitumen can replace diminishing Canadian and U.S. production of refinery-ready light oil. The report projects that a US$1-per-barrel discount for Canadian heavy oil would generate sales of 140,000 barrels daily. The effect of a $1 discount would be almost twice as great for synthetic crude oil. Heavy oil sales rely greatly on maintaining a discount off prices for light grades. A $1-per-barrel premium could destroy demand for bitumen-based blends. Moody's Investors Service claims that deep discounting reflects global market conditions, risking Canadian production of heavy oil grades and seasonal lows in demand for bitumen as a raw material for asphalt

Bitumen-petrolatum hydroinsulation employment in the South-Ukrainian NPP building

International Nuclear Information System (INIS)

Donskov, V.A.; Pochepko, V.P.; Ryaboshapko, Yu.I.; Savenkov, V.V.; Chaplygin, L.A.; Chernyavskij, V.L.

1982-01-01

Method of accomplishment of external hydroinsulation of ferroconcrete constructions by bitumen-petrolatum compositions used in the South-Ukrainian NPP building is described. The speciality of this method lies in establishing the combined cover, which includes concrete layer impregnated by modified petrolatum, and the covering layer from bitumen and petrolatum mixture, and performs not only functions of hydroinsulation but also anticorrosive protection under conditions of highly agressive waters action. Physicomechanical characteristics of bitumen-petrolatum compositions are given and the installation for applying of hydroinsulation compositions is described

Effect of Ultraviolet Aging on Rheology and Chemistry of LDH-Modified Bitumen

Directory of Open Access Journals (Sweden)

Xing Liu

2015-08-01

Full Text Available Layered double hydroxides (LDHs are an ultravioletlight (UV-resistant material. In this study, two types of LDHs (Mg-Al-LDHs and Zn-Al-LDHs were applied to modify bitumen by melt-blending. The effect of ultraviolet aging on the rheology and chemistry of LDH-modified bitumen was studied by means of dynamic shear rheometer (DSR, thin-layer chromatography with flame ionization detection (TLC-FID, Fourier transform infrared spectroscopy (FTIR, and Ultraviolet-Visible (UV-Vis spectrophotometry to reveal the mechanisms of action for LDHs and bitumen. The results showed that within the UV spectra (220–400 nm, the reflectance of Zn-Al-LDHs was larger than that of Mg-Al-LDHs. These two LDHs have different influences on the performance of bitumen. Mg-Al-LDHs had a more obvious influence on the physical and dynamic rheological properties of bitumen than Zn-Al-LDHs. Zn-Al-LDHs improved the UV-aging resistance of bitumen more. The reason can be that the reflectance of the Zn-Al-LDHs to the UV light is larger than that of the Mg-Al-LDHs. The Zn-Al-LDH-modified bitumen had more potential to improve the UV-aging resistance during the service life of asphalt pavement.

The extraction of bitumen from western oil sands. Final report, July 1989--September 1993

Energy Technology Data Exchange (ETDEWEB)

Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Fletcher, J.V.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1994-03-01

Research and development of surface extraction and upgrading processes of western tar sands are described. Research areas included modified hot water, fluidized bed, and rotary kiln pyrolysis of tar sands for extraction of bitumen. Bitumen upgrading included solvent extraction of bitumen, and catalytic hydrotreating of bitumen. Characterization of Utah tar sand deposits is also included.

Latest condition of the steam coal market and outlook for supply cost

Energy Technology Data Exchange (ETDEWEB)

Murase, A.

1988-11-01

The following factors affecting coal prices are identified: rises in the prices of fuels which compete with coal, especially petroleum; the supply cost of coal; coal supply and demand; the balance of power between sellers and buyers; and foreign exchange rates. Coal supply costs are discussed. 5 figs.

Characterization of Bitumen Micro-Mechanical Behaviors Using AFM, Phase Dynamics Theory and MD Simulation

Directory of Open Access Journals (Sweden)

Yue Hou

2017-02-01

Full Text Available Fundamental understanding of micro-mechanical behaviors in bitumen, including phase separation, micro-friction, micro-abrasion, etc., can help the pavement engineers better understand the bitumen mechanical performances at macroscale. Recent researches show that the microstructure evolution in bitumen will directly affect its surface structure and micro-mechanical performance. In this study, the bitumen microstructure and micro-mechanical behaviors are studied using Atomic Force Microscopy (AFM experiments, Phase Dynamics Theory and Molecular Dynamics (MD Simulation. The AFM experiment results show that different phase-structure will occur at the surface of the bitumen samples under certain thermodynamic conditions at microscale. The phenomenon can be explained using the phase dynamics theory, where the effects of stability parameter and temperature on bitumen microstructure and micro-mechanical behavior are studied combined with MD Simulation. Simulation results show that the saturates phase, in contrast to the naphthene aromatics phase, plays a major role in bitumen micro-mechanical behavior. A high stress zone occurs at the interface between the saturates phase and the naphthene aromatics phase, which may form discontinuities that further affect the bitumen frictional performance.

Characterization of Bitumen Micro-Mechanical Behaviors Using AFM, Phase Dynamics Theory and MD Simulation.

Science.gov (United States)

Hou, Yue; Wang, Linbing; Wang, Dawei; Guo, Meng; Liu, Pengfei; Yu, Jianxin

2017-02-21

Fundamental understanding of micro-mechanical behaviors in bitumen, including phase separation, micro-friction, micro-abrasion, etc., can help the pavement engineers better understand the bitumen mechanical performances at macroscale. Recent researches show that the microstructure evolution in bitumen will directly affect its surface structure and micro-mechanical performance. In this study, the bitumen microstructure and micro-mechanical behaviors are studied using Atomic Force Microscopy (AFM) experiments, Phase Dynamics Theory and Molecular Dynamics (MD) Simulation. The AFM experiment results show that different phase-structure will occur at the surface of the bitumen samples under certain thermodynamic conditions at microscale. The phenomenon can be explained using the phase dynamics theory, where the effects of stability parameter and temperature on bitumen microstructure and micro-mechanical behavior are studied combined with MD Simulation. Simulation results show that the saturates phase, in contrast to the naphthene aromatics phase, plays a major role in bitumen micro-mechanical behavior. A high stress zone occurs at the interface between the saturates phase and the naphthene aromatics phase, which may form discontinuities that further affect the bitumen frictional performance.

Optimization bitumen-based upgrading and refining schemes

Energy Technology Data Exchange (ETDEWEB)

Munteanu, M.; Chen, J. [National Centre for Upgrading Technology, Devon, AB (Canada); Natural Resources Canada, Devon, AB (Canada). CanmetENERGY

2009-07-01

This poster highlighted the results of a study in which the entire refining scheme for Canadian bitumen as feedstocks was modelled and simulated under different process configurations, operating conditions and product structures. The aim of the study was to optimize the economic benefits, product quality and energy use under a range of operational scenarios. Optimal refining schemes were proposed along with process conditions for existing refinery configurations and objectives. The goal was to provide guidelines and information for upgrading and refining process design and retrofitting. Critical steps were identified with regards to the upgrading process. It was concluded that the information obtained from this study would lead to significant improvement in process performance and operations, and in reducing the capital cost for building new upgraders and refineries. The simulation results provided valuable information for increasing the marketability of bitumen, reducing greenhouse gas emissions and other environmental impacts associated with bitumen upgrading and refining. tabs., figs.

Extraction of hydrocarbon products from shales and coals

Energy Technology Data Exchange (ETDEWEB)

Reed, V Z

1918-05-17

A process is disclosed of extracting hydrocarbon oil matter from petroleum-bearing shales and coals which comprises subjecting a mass of such shale or coal, before distillation to the solvent action of material containing an acid, permitting the solvent material to pass through the mass of shale or coal, and recovering the combined solvent and extracted matter.

Characterization of liquid products from the co-cracking of ternary and quaternary mixture of petroleum vacuum residue, polypropylene, Samla coal and Calotropis Procera

Energy Technology Data Exchange (ETDEWEB)

M. Ahmaruzzaman; D.K. Sharma [Indian Institute of Technology Delhi, New Delhi (India). Centre for Energy Studies

2008-08-15

The co-cracking of the petroleum vacuum residue (XVR) with polypropylene (PP), Samla coal (SC) and Calotropis procera (CL) has been carried out in a batch reactor under isothermal conditions at atmospheric pressure. The liquids obtained by co-cracking have been characterized by Fourier transform infrared spectroscopy, high performance liquid chromatography, {sup 1}H nuclear magnetic resonance (NMR), {sup 13}C NMR, gel permeation chromatography (GPC), and inductively coupled argon plasma analyses. It was found that the liquid products obtained from the co-cracking of ternary and quaternary mixtures of the petroleum vacuum residue with polypropylene, coal and C. procera contained less than 1 ppm of Ni and V. The HPLC analyses indicates that the liquids obtained from the cracking of ternary mixture of XVR+PP+CL were mainly aliphatic in nature (saturates content 87.4%). NMR analyses showed that the aromatic carbon contents decreased (15.0%) in the liquid products derived from the co-cracking of quaternary mixtures of XVR+PP+SC+CL compared to their theoretical averages (taking the averages of aromatic carbon contents of the liquids from XVR, PP, SC and CL individually). The overall results indicated that there exists a definite interaction of reactive species when XVR, PP, SC and CL were co-cracked together. 27 refs., 5 tabs.

Industrial coal survey

Energy Technology Data Exchange (ETDEWEB)

1992-05-25

UK industrial coal sales were down 400,000t to 7.1mt in 1991. This was largely due to fall in cement purchases as the construction industry was badly hit in the recession. Increased competition from petroleum coke also had an effect. A brief roundup is presented of sales to the UK's major coal buyers: Alcan, ICI, Blue Circle, Castle Cement, Rugby Cement, British Steel, UK Paper, Courtaulds, Unilever, AHS Emstar, Tate Lyle, and British Sugar. 1 tab.

The use of bitumen for storing radioactive waste resulting from oil industry containing Ra-226

International Nuclear Information System (INIS)

Takriti, S.; Shweikani, R.; Abdulhafiz, M.; Salman, M.

2009-12-01

The releases of radon gas from NORM waste contained in two different forms of bitumen samples have been investigated. The artificial NORM source samples were made by mixing NORM with bitumen. The sources surrounded by different thickness of bitumen layers to prepare the first form of samples. While, the NORM powder was put inside bitumen samples prepared as a cylindrical shape with different thickness. The results showed that the release of radon from the bitumen samples was different in case of sources and powder. The results illustrated that the release of radon from the bitumen samples was decrees linearly with the samples thicknesses (in both cases source and powder). On the other hand, the release from the cement samples was proportional inversely with the different thickness (for comparison). In addition, many other supporting experiments were performed, as γ-ray spectroscopy measurements showed that the cement is better than the bitumen in shielding process, while the bitumen is better than cement to prevent the releases of radon. (authors)

Birth and first steps of mineral coal industry in the USA

International Nuclear Information System (INIS)

Martin-Amouroux, Jean-Marie

2015-10-01

The author proposes a brief history of the emergence of a mineral coal industry in the USA. He notices that wood has been the first source of energy used by settlers for housing heating, and then in industry and transports for heat and steam production. As demand and supply conditions were bad, coal production, although mining sites had been quickly identified and used, only emerged from the 1840's. Different kinds of coal (anthracite, bitumen) have been extracted depending on the region. Then, urbanisation and industrialisation created new opportunities for coal, and the share of coal regularly increased. The author describes how the coal industry was organised: seven regions, central position of Pittsburgh. He outlines the tremendous growth of coal production between 1840 and 1913; comments the distribution of this production among the different states. He describes and comments how this production has been industrialised. This industrialisation resulted in a dramatic increase of productivity between 1890 and 1910. He finally evokes the rather late creation of federal bodies

Coating of evaporation concentrates with bitumen. Progress Report No. 1

International Nuclear Information System (INIS)

Rodier, J.; Lefillatre, G.; Rodi, L.; Cudel, Y.

1968-01-01

Laboratory tests have been carried out on the coating by bitumen of evaporation concentrates having a free nitric acidity of 1 N or 2.5 N, and a high mineralization (400 gm/litre). In order to neutralize the free acidity and to trap the radio-elements, these concentrates have been subjected before coating to various treatments designed to decrease the solubility. As a result of these treatments, sludges were obtained which could be coated directly with the bitumen. By measuring the radioactive diffusion factors of the bitumen coated products immersed both in ordinary and sea water, it was possible to compare the efficiency of the processes developed and of the various types of bitumen used. On the whole the radioactive diffusion tests were satisfactory and the process using successive co-precipitations (hydroxides, nickel ferrocyanide, barium sulphate) was chosen. From the bitumens tried out, a straight - asphalt, Mexphalt 40/50 was selected for low and medium activity concentrates as it ensures good isolation of the radio-elements; an air-blowing asphalt, Mexphalte R 90/40, was chosen for concentrates of high activity because of its higher resistance to irradiation. As a result of this work, a simple coating technology was evolved and pilot experiments will soon begin. Briefly, it appears that although a method for coating evaporation concentrates with bitumen has been defined, it will inevitably be necessary to devise a specific decontamination process each time that a new type of concentrate is encountered (composition, nature of the salts, radio-element distribution). (author) [fr

Converting petroleum into acids, soaps, etc

Energy Technology Data Exchange (ETDEWEB)

Imray, J

1883-06-19

The conversion of petroleum and hydrocarbons resulting from distillation of lignite, coal, peat, shale, etc., into organic acids by treating the hydrocarbons in the presence of caustic alkalies, alkaline earths, alkaline carbonates, or other bodies with alkaline reaction, with a current of air or oxygen, with or without pressure, at a raised temperature, and decomposing the soaps formed, the free acid being removed from the compound which is then separated into single fractions by fractional distillation or by taking advantage of the unequal solubility in petroleum or similar solvents is described.

Solid colloidal particles inducing coalescence in bitumen-in-water emulsions.

Science.gov (United States)

Legrand, J; Chamerois, M; Placin, F; Poirier, J E; Bibette, J; Leal-Calderon, F

2005-01-04

Silica particles are dispersed in the continuous phase of bitumen-in-water emulsions. The mixture remains dispersed in quiescent storage conditions. However, rapid destabilization occurs once a shear is applied. Observations under the microscope reveal that the bitumen droplets form a colloidal gel and coalesce upon application of a shear. We follow the kinetic evolution of the emulsions viscosity, eta, at constant shear rate: eta remains initially constant and exhibits a dramatic increase after a finite time, tau. We study the influence of various parameters on the evolution of tau: bitumen droplet size and volume fraction, silica diameter and concentration, shear rate, etc.

Qingshankou-Putaohua/Shaertu and Jurassic Coal-Denglouku/Nongan total petroleum systems in the Songliao Basin, China

Science.gov (United States)

Ryder, Robert T.; Qiang, Jin; McCabe, Peter J.; Nuccio, Vito F.; Persits, Felix

2003-01-01

The Qingshankou-Putaohua/Shaertu petroleum system involves the generation of oil and gas from a mature pod of lacustrine source rock near the center of the Songliao Basin in northeastern China. The primary source rock is the Lower Cretaceous Qingshankou Formation, and a secondary source rock is Member 1 of the Lower Cretaceous Nenjiang Formation. The most productive of six sandstone reservoirs are the Putaohua reservoir (Member 1 of the Lower Cretaceous Yaojia Formation) and the Shaertu reservoir (Members 2 and 3 of the Yaojia Formation and Member 1 of the Nenjiang Formation). Most oil and associated gas generated from the Qingshankou Formation and Nenjiang Formation (Member 1) are trapped in large faulted anticlines, fault blocks, and faulted anticlinal noses in combination with facies-change and (or) diagenetic stratigraphic traps. Two assessment units are defined in the petroleum system: (1) an anticlinal assessment unit; and (2) a subtle-traps assessment unit consisting of (a) anticlinal noses in combination with fault or stratigraphic traps, (b) stratigraphic traps, and (c) unconventional reservoirs. Undiscovered conventional oil and gas resources are expected in both assessment units in small (5?10 million barrels of oil; 30?60 billion ft3 gas) and medium (10?25 million barrels of oil; 60?150 billion ft3 of gas) fields. Also, undiscovered conventional oil and gas resources are expected in several large fields (25?73 million barrels of oil; 150?173 billion ft3 of gas). The Jurassic coal?Dengloukou/Nongan petroleum system involves the generation of natural gas from multiple pods of mature source rock in graben structures at the base of the Songliao Basin. Sandstone and conglomeratic sandstone in the Lower Cretaceous Denglouku Formation and the Lower Cretaceous Quantou Formation are the major reservoir rocks. Most of the known natural gas is trapped in anticlines, anticlinal noses, and fault blocks. This petroleum system is largely unexplored in comparison to

Assessment of Appalachian basin oil and gas resources: Carboniferous Coal-bed Gas Total Petroleum System: Chapter G.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Milici, Robert C.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

The Carboniferous Coal-bed Gas Total Petroleum System, which lies within the central and southern Appalachian basin, consists of the following five assessment units (AUs): (1) the Pocahontas Basin AU in southern West Virginia, eastern Kentucky, and southwestern Virginia; (2) the Central Appalachian Shelf AU in Tennessee, eastern Kentucky, and southern West Virginia; (3) the East Dunkard (Folded) AU in western Pennsylvania and northern West Virginia; (4) the West Dunkard (Unfolded) AU in Ohio and adjacent parts of Pennsylvania and West Virginia; and (5) the Appalachian Anthracite and Semi-Anthracite AU in Pennsylvania and Virginia. Only two of these assessment units were assessed quantitatively by the U.S. Geological Survey (USGS) in the National Oil and Gas Assessment in 2002. The USGS estimated the Pocahontas Basin AU and the East Dunkard (Folded) AU to contain a mean of about 3.6 and 4.8 trillion cubic feet (TCF) of undiscovered, technically recoverable gas, respectively.

IARC 1987 re-evaluation of carcinogenicity of mineral oils and bitumens - CONCAWE comments and interpretation

Energy Technology Data Exchange (ETDEWEB)

1988-10-01

Following the IARC response to CONCAWE comments on their 1987 re-evaluation of carcinogenicity of mineral oils and bitumens, CONCAWE decided that a revised version of Report No. 87/63 should be published in this report. The objective is to ensure that all who may be concerned with carcinogenicity classifications of these petroleum products, including national and international regulatory authorities, are aware of the reasons for the differences between the 1984 and 1987 IARC classifications and of CONCAWE's reservations concerning the revised classifications. This document reviews important differences between the new and previous evaluations, which are summarized in tabular form, and also indicates how the differences have occurred. In addition, it provides CONCAWE's interpretation of the available evidence, taking into account points discussed with IARC. 1 tab.

Speciation of Heavy Metals in Sediment of Agbabu Bitumen deposit ...

African Journals Online (AJOL)

Michael Horsfall

environmental impact assessment of bitumen exploitation on animal resources of Ode – Irele. (Lameed and Ogunsusi, 2002), compositional analysis of the oil component of the Nigerian bitumen (Oderinde and Olanipekun, 1991),. Distribution of Polycyclic Aromatic hydrocarbons in soils and water from the vicinity of Agbabu ...

Effect of fast pyrolysis bio-oil from palm oil empty fruit bunch on bitumen properties

Science.gov (United States)

Poh, Chia Chin; Hassan, Norhidayah Abdul; Raman, Noor Azah Abdul; Shukry, Nurul Athma Mohd; Warid, Muhammad Naqiuddin Mohd; Satar, Mohd Khairul Idham Mohd; Ros Ismail, Che; Asmah Hassan, Sitti; Mashros, Nordiana

2018-04-01

Bitumen shortage has triggered the exploration of another alternative waste material that can be blended with conventional bitumen. This study presents the performance of pyrolysis bio-oil from palm oil empty fruit bunch (EFB) as an alternative binder in modified bitumen mixtures. The palm oil EFB was first pyrolyzed using auger pyrolyzer to extract the bio-oil. Conventional bitumen 80/100 penetration grade was used as a control sample and compared with samples that were modified with different percentages, i.e., 5% and 10%, of pyrolysis EFB bio-oil. The physical and rheological properties of the control and modified bitumen samples were investigated using penetration, softening point, viscosity and dynamic shear rheometer (DSR) tests. Results showed that the addition of EFB bio-oil softened the bitumen with high penetration and a reduction in softening point, penetration index, and viscosity. However, the DSR results showed a comparable rutting resistance between the bitumen samples containing EFB bio-oil and virgin bitumen with a failure temperature achieved greater than 64°C.

Bitumen nanocomposites with improved performance

KAUST Repository

Kosma, Vasiliki

2017-11-29

Bitumen-clay nanocomposite binders with styrene-butadienestyrene triblock copolymer, SBS, and combinations of SBS and crumb rubber (CR) with different CR/SBS ratios have been synthesized and characterized. In addition to the binder, samples containing the binder and concrete sand (with a weight ratio 1:9) were prepared. The modified binders were studied in terms of filler dispersion, storage stability, mechanical performance and water susceptibility. We demonstrate that the samples containing nanoclays consistently outperform those based only on the polymer additives. We also find that nanocomposite samples based on a combination of SBS and CR are best, since in addition to other improvements they show excellent storage stability. Our work shows that substituting CR with SBS as a bitumen additive and combining it with inexpensive nanoclays leads to new materials with enhanced performance and improved stability for practical asphalt applications.

Report on the research achievements in the Sunshine Project in fiscal 1990. Studies on coal liquefying reaction, and reforming and utilization of the products; 1990 nendo sekitan no ekika hanno to seiseibutsu no kaishitsu riyo no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

This paper describes the achievements in the Sunshine Project in fiscal 1990 on research of coal liquefying reaction. The research contributes to developing a coal liquefaction technology as one of the methods for manufacturing clean energy and chemical raw materials from coal. In the fundamental study on the liquefaction, primarily liquefied heavy constituents in different types of coals were divided into such constituents as HI, TI, and THFI to discuss the performance and coking behavior of each constituent as solvent. Furthermore, effects of hydrogenation treatment were also elucidated. Decomposing reaction was performed on different heavy products to discuss effects of the reaction conditions. In the liquefying reaction using petroleum-based heavy oil as solvent, different shale oils were used in experiments for comparison with the case of using tar sand bitumen. In the study of reforming the product, comparison was carried out on reactions in hydrogenation treatment and contact decomposition of medium to heavy fractions of liquefied oil. A separation experiment was made on hetero compounds by means of solvent extraction and pressure crystallization of liquefied oil naphtha and light oil fraction. Effects of additive were investigated in an engine test on the stabilized and balanced light oil fraction. Discussions were given on high level utilization of heat treated oil recovered from residues in liquefaction distillation. (NEDO)

Effect of annealing conditions on the molecular properties and wetting of viscoelastic bitumen substrates by liquids

Directory of Open Access Journals (Sweden)

Salomé dos Santos

2017-01-01

Full Text Available Typically, in the production of asphalt concrete, bitumen and mineral aggregates are heated and mixed at temperatures above 100 °C. After the mixing process bitumen ideally coats the mineral aggregates and remains in the form of thin films. Because bitumen is highly temperature sensitive, the study of its properties in terms of chemistry, microstructure and rheology as a function of different annealing conditions is very relevant. The resultant molecular properties have a direct correlation to bitumen macroscopic response to liquids such as water, which is of extreme relevance to the understanding of the detrimental effect of water on asphalt pavements. The wetting characteristics play a crucial role on the extension of detachment of bitumen from the mineral aggregates when asphalt is exposed to wet conditions. Therefore, in this work, the effect of the annealing temperature and cooling history on the chemistry, microstructure and wetting of bitumen films was studied. Crystalline microstructures were identified in bulk and on the surface of the bitumen films. Larger crystals presenting higher crystallinity degree were identified when the annealed bitumen films were cooled slowly. Moreover, higher annealing temperatures increased the oxidation level. The change of the rheological properties due to the alterations of the annealing conditions produced changes in the wetting characteristics. For instance, the advancing motion of a liquid drop on the viscoelastic bitumen substrate presented an intermittent behaviour due to the deformation of bitumen at the liquid-bitumen-air contact line. Consequently, changes in the contact angles were also observed. Keywords: Bitumen, Crystallization, Oxidation, Advancing contact angle, Wetting

The world coal market: supplies, prices, transport (Review)

International Nuclear Information System (INIS)

Drozdnik, I.D.; Kaftan, Yu.S.; Dolzhanskaya, Yu.B.

1998-01-01

The state of the world coal market in the period of 1994-1997 is reviewed, its long-term outlooks are presented. The major world coal exporters-Australia, Canada, China, Poland, Russia, the USA, SAR, and Ukraine are briefly characterized. It is pointed out that in the foreseeable future coal will retain its importance of a primary energy carrier along with petroleum and natural gas

Effect of Temperature and Process on Quantity and Composition of Laboratory-generated Bitumen Emissions.

Science.gov (United States)

Bolliet, Christophe; Kriech, Anthony J; Juery, Catherine; Vaissiere, Mathieu; Brinton, Michael A; Osborn, Linda V

2015-01-01

In this study we investigated the impact of temperature on emissions as related to various bitumen applications and processes used in commercial products. Bitumen emissions are very complex and can be influenced in quantity and composition by differences in crude source, refining processes, application temperature, and work practices. This study provided a controlled laboratory environment to study five bitumen test materials from three European refineries; three paving grade, one used for primarily roofing and some paving applications, and one oxidized industrial specialty bitumen. Emissions were generated at temperatures between 140°C and 230°C based on typical application temperatures of each product. Emissions were characterized by aerodynamic particle size, total organic matter (TOM), simulated distillation, 40 individual PACs, and fluorescence (FL-PACs) spectroscopy. Results showed that composition of bitumen emissions is influenced by temperature under studied experimental conditions. A distinction between the oxidized bitumen with flux oil (industrial specialty bitumen) and the remaining bitumens was observed. Under typical temperatures used for paving (150°C-170°C), the TOM and PAC concentrations in the emissions were low. However, bitumen with flux oil produced significantly higher emissions at 230°C, laden with high levels of PACs. Flux oil in this bitumen mixture enhanced release of higher boiling-ranged compounds during application conditions. At 200°C and below, concentrations of 4-6 ring PACs were ≤6.51 μg/m(3) for all test materials, even when flux oil was used. Trends learned about emission temperature-process relationships from this study can be used to guide industry decisions to reduce worker exposure during processing and application of hot bitumen.

Annual bulletin of coal statistics for Europe. Vol. IX

Energy Technology Data Exchange (ETDEWEB)

1974-01-01

Tables are presented giving the following information: Production, imports, exports, and deliveries of solid fuels with the subdivisions: hard coal, patent fuel, and cokeoven coke; gas coke; brown coal, brown coal briquets, and brown coal coke; and pech coal (hard brown coal produced in the area between the rivers Inn and Lech); Hard coal mines (structure of production, employment and productivity of labor); Brown coal mines (production, employment and productivity of labor); Imports of solid fuels, by country; Exports of solid fuels, by country; and Production of hydroelectric energy and natural gas, and deliveries of petroleum products for inland consumption.

Executive summary: Chapter A.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Ruppert, Leslie F.; Ryder, Robert T.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

Fossil fuels from the Appalachian basin region have been major contributors to the Nation’s energy needs over much of the last three centuries. Early records indicate that Appalachian coal was first mined in the middle 1700s (Virginia and Pennsylvania) and was used sparingly to fuel colonial settlements and, later, a fledgling industrial-based economy along the eastern seaboard of the United States (de Witt and Milici, 1989). In 2011, central Appalachian basin coal production accounted for approximately 77 percent of all U.S. metallurgical (or coking) coal and 29 percent of total U.S. production (U.S. Energy Information Administration, 2013). Following initial discoveries and commercial use in western New York (1821) and Ohio and West Virginia (mid-1830s), the Appalachian petroleum (oil and gas) industry began in earnest in 1859 with the discovery of oil at the Drake well in northwestern Pennsylvania. Between 1860 and 1989, the Appalachian basin produced more than 2.5 billion barrels of oil (BBO) and more than 30 trillion cubic feet of gas (TCFG) from more than 500,000 wells (de Witt and Milici, 1989). Although both oil and gas continue to be produced in the Appalachian basin, most new wells in the region are drilled in shale reservoirs to produce natural gas.

The Chuar Petroleum System, Arizona and Utah

Science.gov (United States)

Lillis, Paul G.

2016-01-01

The Neoproterozoic Chuar Group consists of marine mudstone, sandstone and dolomitic strata divided into the Galeros and Kwagunt Formations, and is exposed only in the eastern Grand Canyon, Arizona. Research by the U.S. Geological Survey (USGS) in the late 1980s identified strata within the group to be possible petroleum source rocks, and in particular the Walcott Member of the Kwagunt Formation. Industry interest in a Chuar oil play led to several exploratory wells drilled in the 1990s in southern Utah and northern Arizona to test the overlying Cambrian Tapeats Sandstone reservoir, and confirm the existence of the Chuar in subcrop. USGS geochemical analyses of Tapeats oil shows in two wells have been tentatively correlated to Chuar bitumen extracts. Distribution of the Chuar in the subsurface is poorly constrained with only five well penetrations, but recently published gravity/aeromagnetic interpretations provide further insight into the Chuar subcrop distribution. The Chuar petroleum system was reexamined as part of the USGS Paradox Basin resource assessment in 2011. A map was constructed to delineate the Chuar petroleum system that encompasses the projected Chuar source rock distribution and all oil shows in the Tapeats Sandstone, assuming that the Chuar is the most likely source for such oil shows. Two hypothetical plays were recognized but not assessed: (1) a conventional play with a Chuar source and Tapeats reservoir, and (2) an unconventional play with a Chuar source and reservoir. The conventional play has been discouraging because most surface structures have been tested by drilling with minimal petroleum shows, and there is some evidence that petroleum may have been flushed by CO2 from Tertiary volcanism. The unconventional play is untested and remains promising even though the subcrop distribution of source facies within the Chuar Group is largely unknown.

ELASTICITY OF BITUMEN BINDERS AND THE FACTORS CAUSING IT

Directory of Open Access Journals (Sweden)

A. Galkin

2015-12-01

Full Text Available The article deals with the influence of the initial bitumen penetration grade and different con-centrations of the mineral filler on the elasticity of the polymer-modified bitumen (PMB with 3 and 6 % of SBS type polymer. The dependences of elasticity of the PMB on the test conditions – such as the temperature and the stress state level are shown additionally.

Refining and end use study of coal liquids II - linear programming analysis

Energy Technology Data Exchange (ETDEWEB)

Lowe, C.; Tam, S.

1995-12-31

A DOE-funded study is underway to determine the optimum refinery processing schemes for producing transportation fuels that will meet CAAA regulations from direct and indirect coal liquids. The study consists of three major parts: pilot plant testing of critical upgrading processes, linear programming analysis of different processing schemes, and engine emission testing of final products. Currently, fractions of a direct coal liquid produced form bituminous coal are being tested in sequence of pilot plant upgrading processes. This work is discussed in a separate paper. The linear programming model, which is the subject of this paper, has been completed for the petroleum refinery and is being modified to handle coal liquids based on the pilot plant test results. Preliminary coal liquid evaluation studies indicate that, if a refinery expansion scenario is adopted, then the marginal value of the coal liquid (over the base petroleum crude) is $3-4/bbl.

Primary migration of Jurassic coal-derived oil in Santanghu basin

Energy Technology Data Exchange (ETDEWEB)

Zhang, W.; Zhong, N.; Ren, D. [China University of Mining and Technology, Beijing (China). Dept of Resource Exploitation Engineering

2000-11-01

It is known that the differential evolution of the multiple macerals results in 'oil generation by stage', and that 'early generation, early expulsion' is one of the preconditions for the efficient accumulation of the coal-derived oil. Based upon the study on the evolution of the physical properties, related to the hydrocarbon expulsion, of the Jurassic organic rock in Santanghu basin during the course of maturation, the mechanism of the primary migration of its coal-derived oil was discussed. The rapid loss of the inherent moisture in the organic rock was not accordant with the main generation stage of the coal-derived oil, so it was unrealistic that the oil migrated by dissolution in the expelled water. It is thought that the special forming mechanism of the continuous 'bitumen network' under the condition of over-pressure and an earlier history of primary migration may be essential to the Jurassic coal-derived oil in Santanghu basin. 17 refs., 4 figs.

Identification of CYP1A inducing compounds in crude oil

Energy Technology Data Exchange (ETDEWEB)

Khan, C.W.; Hodson, P.V. [Queen' s Univ., Kingston, ON (Canada). Dept. of Biology; Hollebone, B.P.; Wang, Z. [Environment Canada, Ottawa, ON (Canada). Environmental Technology Advancement Directorate; Brown, R.S. [Queen' s Univ., Kingston, ON (Canada). Dept. of Chemistry

2004-07-01

One of the major sources of polycyclic aromatic hydrocarbons (PAHs) in aquatic ecosystems is crude oil. PAHs are responsible for developmental malformations in the early life stages of fish. The induction of CYP1A enzyme is characteristic of developmental toxicity caused by crude oil. As such, it is an effective biomarker of PAH uptake. It is not known which PAHs cause toxicity because of the complex chemical composition of crude oil. In this study, an approach called Toxicity Identification and Evaluation (TIE) was used with different crude oils to separate bioavailable PAHs into petroleum sub-fractions. The extent of CYP1A induction in rainbow trout was measured after 48 hour exposures to each fraction. Low temperature vacuum distillation was used to create white gas, kerosene, coal tar/bitumen and wax fractions. Hepatic CYP1A activity was induced by whole oil and some fractions. The highest PAH concentration was found in the coal tar/bitumen fraction which accounted for most CYP1A induction in whole oil. The wax fraction also caused moderate CYP1A induction, but the white gas fraction did not cause any CYP1A induction. The hypothesis that alkyl PAH may be the most significant source of CYP1A inducers in the coal tar/bitumen fraction was supported by chemical analysis of CYP1A induction potency. Results showed that benzo[a]pyrene accounts for nearly all of the CYP1A induction caused by the wax fraction.

Shale oil. II. Gases from oil shale

Energy Technology Data Exchange (ETDEWEB)

McKee, R H; Manning, P D.V.

1927-01-01

Oil shale (from Colorado) was pyrolyzed, and the gaseous products obtained were studied. The organic material present in oil shale contains carboxyl groups that lose carbon dioxide during pyrolysis before the formation of soluble bitumen. Nitrogen was evolved as ammonia in two stages and was not continuous. The first evolution was from loosely combined nitrogen structures, whereas the second was from more stable forms. No hydrocarbons were present as such in the kerogen. The gaseous products from oil-shale pyrolysis were similar to those obtained by distillation of colophony, amber, coal, and wood. This places the kerogen of the oil shale in the same series of carbonaceous substances as those from which coals are formed. Kerogen appeared to be decomposed in three steps; namely, to insoluble bitumen, to soluble bitumen, and to oil (gas evolution accompanied each step). Its low solubility and the character of its pyrolytic gas indicated that kerogen is largely a resinous residue from vegetation of the past era and may have been formed by the tranportation of coal-forming organic debris to inland salty lakes or carried to the sea by clay-laden waters. The salt water and the natural settling action precipitated the clay and organic matter in an almost homogeneous deposit. Oil shales have existed to the present time because they have not been subjected to high pressures or elevated temperatures that would have changed them to petroleum.

Bitumen extraction from oil sands ore-water slurry using CaO (lime) and or ozone

Energy Technology Data Exchange (ETDEWEB)

Babadagli, T. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Alberta Univ., Edmonton, AB (Canada); Burkus, Z.; Moschopedis, S.E.; Ozum, B. [Apex Engineering Inc., Calvert City, KY (United States)

2008-10-15

Reductions in the surface and interfacial tensions in oil sands ore-water slurry systems improve bitumen extraction processes from oil sands ore structures and promote the attachment of air bubbles to liberated bitumen droplets. This study provided details of a non-caustic bitumen extraction process where oil sands slurries were conditioned by bitumen asphaltenes modified to act as surfactants. Oil sands ore-water slurry extraction processes were optimized by adding lime (CaO) and oxidizing bitumen asphaltenes with ozone (O{sub 3}). Experiments were conducted using oil sands ore and process water samples from Alberta. Extraction tests were performed to investigate the effects of various CaO and O{sub 3} dosages and treatment retention times on bitumen extraction efficiency on operating temperatures of 20, 35 and 50 degrees C. A Dean-Stark extraction apparatus was used to determine the amount of bitumen contained in the ore, froth, and in left-over tailings. Process water and release water chemistry were also monitored. Bitumen extraction efficiency was defined as the percentage of bitumen recovered in the resulting froth. Use of the slurries allowed high extraction efficiencies at a temperature of 35 degrees C. Energy consumption and carbon dioxide (CO{sub 2}) emissions were also reduced. The study showed that both additions resulted in significant improvements in bitumen extraction efficiency. Use of the technique also eliminated the accumulation of Na{sup +} ions in produced water. It was concluded that further tests are needed in order to commercialize the CaO and O{sub 3} based techniques. 14 refs., 1 tab., 4 figs.

Effect of different sizes of palm oil fuel ash (POFA) towards physical properties of modified bitumen

Science.gov (United States)

Raja Zulkefli, R. N. A.; Yaacob, H.; Putra Jaya, R.; Warid, M. N. M.; Hassan, N.; Hainin, M. R.; Idham, M. K.

2018-04-01

In the past decades, numerous numbers of studies have been carried out to find ways enhancing properties of bitumen. Other than using polymer, agricultural waste such as palm oil fuel ash (POFA) is one of the waste products that can be used to modify bitumen. In this study, the physical and rheological properties of POFA modified bitumen were examined based on different grinding hour and different percentage of POFA. The bitumen were mixed with different percentages of POFA (0, 5 and 7%) which passed through 0.075 mm sieve and grinded at different period (1 and 4 hour). The samples were then tested and compared to conventional bitumen. From TEM results, POFA grinded at 1 hour have sizes between 3-7 µm while POFA grinded for 4 hours have finer sizes between 500 nm to 3 µm. The results showed that fineness of POFA affect properties of bitumen significantly. Decreasing in penetration value and decreasing in softening temperature indicates that the modified bitumen becomes harder than conventional bitumen. Modified bitumen gives best results when added with 7% POFA sizes of 500 nm to 3 µm compared to 3 to 7 µm.

Evaluating the utility of hydrocarbons for Re-Os geochronology : establishing the timing of processes in petroleum ore systems

Energy Technology Data Exchange (ETDEWEB)

Selby, D.; Creaser, R.A. [Alberta Univ., Edmonton, AB (Canada). Dept. of Earth and Atmospheric Sciences

2005-07-01

Oil from 6 Alberta oil sands deposits were analyzed with a rhenium-osmium (Re-Os) isotope chronometer, an emerging tool for determining valuable age information on the timing of petroleum generation and migration. The tool uses molybdenite and other sulphide minerals to establish the timing and duration of mineralization. However, establishing the timing events of petroleum systems can be problematic because viable sulphides for the Re-Os chronometer are often not available. Therefore, the known presence of Re and Os associated with organic matter in black shale, a common source of hydrocarbons, may suggest that bitumen and petroleum common to petroleum systems may be utilised for Re-Os geochronology. This study evaluated the potential of the Re-Os isotopic system for geochronology and as an isotopic tracer for hydrocarbon systems. The evaluation was based on Re-Os isotopic analyses of bitumen and oil sands. Hydrocarbons formed from migrated oil in both Alberta oil sand deposits and a Paleozoic Mississippi Valley-type lead-zinc deposit contain significant Re and Os contents with high {sup 187}Re/{sup 188}Os and radiogenic {sup 187}Os/{sup 188}Os ratios suitable for geochronology. The oil from the 6 Alberta oil sand deposits yields Re-Os analyses with very high Re/{sup 188}Os ratios, and radiogenic Os isotopic compositions. Regression of the Re-Os data yields a date of 116 {+-} 27 Ma. This date plausibly represents the period of in situ radiogenic growth of {sup 187}Os following hydrocarbon migration and reservoir filling. Therefore, directly dating these processes, and this formation age corresponds with recent burial history models for parts of the Western Canada Sedimentary Basin. The very high initial {sup 187}Os/{sup 188}Os for this regression requires rocks much older than Cretaceous for the hydrocarbon source.

Feasibility study on recovery and utilization of coal mine gas (CMG) at Donetsk Coal Field

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of getting petroleum substitution energy and reducing greenhouse effect gas emission, an investigational study was carried out of the project for methane gas recovery/utilization at the Donbassa coal mine in Ukraine. At the Donbassa coal mine, degassing by test boring is being conducted to reduce the gas emission at coal face for safety, but most of the gas is discharged into the air. In this project, the following were studied: degassing boring/gas induction from bore hole/measurement in gas induction pipe, gas recovery system combined with gas induction in flyash, and installation/operation of gas engine power generation facilities (1,710kW x 7 units) with exhaust heat recovery boiler using the recovered methane gas as fuel. The results obtained were the petroleum substitution amount of 31,000 toe/y and the amount of greenhouse effect gas reduction of 480,000 t/y. In the economical estimation, the initial investment amount was 3 billion yen, the profitability of the total investment used was 2.9%, and the internal earning rate was 6.5%. (NEDO)

Perbaikan Sifat Reologi Visco-Elastic Aspal dengan Penambahan Asbuton Murni Menggunakan Parameter Complex Shear Modulus

Directory of Open Access Journals (Sweden)

Eva Wahyu Indriyati

2013-06-01

Full Text Available The increasing demand of crude oil will increase the price of petroleum asphalt. Indonesia has imported asphalt to meet the need for the annually road construction and maintenance. One solution to improving the rheological properties of bitumen is by adding the harder bitumen or other chemical compound to reduce dependence to petroleum asphalt. In Indonesia there is a source of natural asphalt in Buton Island, Sulawesi with huge amount of deposit that potentially could improve the rheological properties of Pen 60/70 Petroleum Asphalt. In order to obtain a better understanding on the contribution of Asbuton to the improvement of performance on rheological properties, this research used 19 variations of Asbuton and pen 60/70 petroleum bitumen. This variation is then subjected to the basic rheology test and the mechanistic test using Dynamic Shear Rheometer. The conclusion of basic rheological performance is obtained that mixture (Asbuton and 60/70 petroleum bitumen will increase hardness of bitumen. Conclusion on mechanistic rheological performance is that mixture (Asbuton and 60/70 petrol bitumen will increase Performance Grade (PG and Complex Shear Modulus (G*. The results from the analysis of Master Curve and Black Diagram, it is shown that the increasing proportion of bitumen Asbuton will decrease the phase angle (δ but its temperature susceptibility is worse.

Effect of processing temperature on the bitumen/MDI-PEG reactivity

Energy Technology Data Exchange (ETDEWEB)

Martin-Alfonso, M.J.; Partal, P.; Navarro, F.J.; Garcia-Morales, M. [Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales, Campus de ' El Carmen' , Universidad de Huelva, 21071, Huelva (Spain); Bordado, J.C.M. [Chemical and Biological Engineering Department, IBB, Instituto Superior Tecnico, Av. Rovisco Pais 1049-001 Lisbon (Portugal); Diogo, A.C. [Materials Engineering Department, Instituto Superior Tecnico, Av. Rovisco Pais 1049-001 Lisbon (Portugal)

2009-04-15

Reactive polymers are lately gaining acceptance to give added value to a residue of the crude oil refining process such as bitumen. The resulting material should display enhanced mechanical properties to be considered for advanced applications in construction. In the present paper, we report the effect of processing temperature on the reaction between bitumen compounds and an isocyanate-based reactive polymer, synthesized by reaction of polymeric MDI (4,4'-diphenylmethane diisocyanate) with a low molecular weight polyethylene-glycol (PEG). Rheokinetics experiments, viscosity measurements at 60 C, atomic force microscopy (AFM) characterization, thin layer chromatography (TLC-FID) analysis and thermogravimetric studies (TGA) were performed on the reactive polymer and on samples of MDI-PEG modified bitumen containing 2 wt.% of the polymer. Results showed the existence of an optimum processing temperature arisen as a consequence of opposite effects: microstructural availability for the formation of a polymer-bitumen network, reaction ability and polymer thermal degradation. Consequently, this study aims to serve as a guideline for the refining and asphalt industries facing the stage of selecting the optimum processing parameters. (author)

Comparative study of modified bitumen binder properties collected from mixing plant and quarry.

Science.gov (United States)

Mustafa Kamal, M.; Abu Bakar, R.; Hadithon, K. A.

2017-11-01

Quality control and assurance are essential in pavement construction. In general, the properties of bitumen change as it ages in bulk storage, transport, and storage on site. The minimization of bituminous hardening during storing, transportation and mixing depends on careful control of binder temperature. Hence therefore, bitumen should always be stored and handled at the lowest temperature possible, consistent with efficient use. The objective of the work is to monitor the quality of bitumen samples collected from mixing plant and quarry. Results showed that, samples modified bitumen which collected from quarry showed some adverse effects on rheological properties and physical properties after subjecting to high temperature storage within a period of time. The dynamic stiffness, elastic properties and other common binder properties were deteriorated too. The chemical changes that occurred during storage were analysed using Fourier transform infra-red spectroscopy (FTIR). Thus studies developed an understanding of bitumen ageing in storage.

A method for processing peat or brown coal

Energy Technology Data Exchange (ETDEWEB)

Belkevich, P.I.; Lishtvan, I.I.; Prokhorov, G.M.; Tolstikov, G.A.

1983-01-01

A method is patented for extraction of peat and brown coal using dimethylformamide or dimethylsulfoxide in order to increase the output of bitumen and to produce dyes and acids from it and to utilize the debituminized fuel. The extraction is conducted at a solvent to raw material ratio of 1 to 5 at a temperature of 95 to 160 degrees for 0.5 to 3 hours. The extract is processed by hydroxides or carbonates of alkaline metals at a ratio of extract to the bitumen of 0.1 to 0.5 at 95 to 160 degrees for 0.5 to 2 hours with isolation of the salts of carbonic acids and recrystallization of them from the hydroxide with the acquisition of the target product of humic acids. The solvent is distilled from the extraction residue and after drying the sediment, a dye D is produced, while the debituminized fuel is processed by hydroxides of alkaline metals in a 0.1 to 1 to 1 ratio at 100 to 150 degrees for 0.5 to 2 hours with the acquisition of thinner for cement solutions. Example. A suspension of 180 grams of peat with a particle size of 0.25 to 10 millimeters with indicators (in percent) of the degree of breakdown of 40, moisture level of 20, ash content of 3.1 and bitumen content of 4.2, is mixed with 810 grams of dimethylformamide (an extraction agent to peat ratio of 4.5) and is heated at 95 degrees for three hours. Eight hundred and seventy grams of the extract (the bitumen output is 33 percent) are acquired, along with 120 grams of debituminized peat. Thirty grams of NaOH (an alkaline to bitumen ratio of 0.5) is gradually added to the bitumen extract at 90 to 100 degrees. The reaction mixture is heated to 160 degrees and is cured at this temperature for 2 hours and subsequently cooled to 20 degrees, filtered off and the salts of the carbonic acids are washed out by a fresh portion of dimethylsulfoxide with the production of 21.3 grams of salts with a melting point of 122 to 175 degrees.

Distilling coal

Energy Technology Data Exchange (ETDEWEB)

Blythe, F C

1914-09-14

In the destructive distillation of bituminous coal, heavy hydrocarbon oil, such as petroleum, kerosine, shale oil, and heavy tar oil, obtained in some cases during the process, is added to the coal, which is then distilled under pressure and at a comparatively low temperature regulated so as to produce a large proportion of hydrocarbon oils and a small proportion of permanent gas. In one method, about 5 to 10 parts of hydrocarbon oil are mixed with 100 parts of crushed or ground coal, and the mixture is heated in a closed vessel, provided in some cases with an agitator, under a pressure of about 60 lb/in/sup 2/, and the temperature may be gradually raised to 350/sup 0/C and then to about 500/sup 0/C. The heating may be by means of superheated steam with or without external heat.

Proceedings of the 58. annual technical meeting of the Petroleum Society of CIM : CIPC 2007 : Because technology changes everything

International Nuclear Information System (INIS)

Laureshen, C.; Cuthiell, D.

2007-01-01

This conference and trade show provided a forum to present new, emerging and existing technologies that will play a key role in ensuring that hydrocarbon exploitation occurs in a sustainable manner, where costs and resource recovery are optimized while minimizing environmental impacts. The challenge of developing maturing basins, frontier lands and unconventional resources was discussed. In particular, the application of thermal recovery methods such as steam assisted gravity drainage (SAGD) for the in-situ recovery of heavy oils and bitumens was reviewed and compared with the performance of alternative enhanced energy recovery technologies such as vapor extraction (VAPEX). The conference was attended by local and international participants in the petroleum sector, including managers, engineers, technologists, geologists, and other petroleum industry specialists. The conference featured 132 presentations addressing topics such as improved recovery of conventional oil and gas; heavy oil cold production; thermal and solvent methods for recovering heavy oil and bitumen; drilling engineering; well completions and simulation; well test analysis; production operations and optimization; facilities; reservoir rock and fluids characterization; numerical simulation; health, safety and regulatory issues; oil and gas and the environment; and, business development and risk management. All 132 presentations from the conference have been catalogued separately for inclusion in this database. refs., tabs., figs

Structural Evolution of Kerogen and Bitumen during Thermal Maturation examined by Fourier-Transform Infrared Spectroscopy

Science.gov (United States)

Craddock, P. R.; Le Doan, T. V.; Pomerantz, A.

2014-12-01

Kerogen—the organic matter that is solid and insoluble in organic solvents—is a key component of organic-rich mudstones. The composition of kerogen affects the storage and transport of hydrocarbons in these unconventional resources and is known to change with thermal maturity. We report here using FTIR spectroscopy, the compositional characteristics of kerogen as a function of thermal maturity, together with the compositional characteristics of the organic phase, bitumen—the organic matter that is solid, but soluble in organic solvents. Kerogen is consumed during thermal maturation, whereas bitumen is an intermediary formed at low maturity from kerogen and consumed at higher maturities in formation of oil and gas. Bitumen relative to kerogen has higher aliphatic content, lower aromatic content, and lower abundance of oxygenated functions. At low maturity (vitrinite reflectance equivalent VRe ~ 0.5-0.9 %), the average length of aliphatic chains in bitumen increases during bitumen formation. At higher thermal maturities (VRe > 1.0-1.3 %), average aliphatic chain length decreases as bitumen is consumed. This evolution contrasts to that in kerogen, where aliphatic chain lengths shorten during all stages of maturation. Breakdown of kerogen appears to be driven by cleavage of oxygen functions at low maturity and removal of aliphatic carbons at higher maturities. These aliphatic-rich fragments may comprise the bitumen, and may in part explain the solubility of bitumen in organic solvents. Bitumen shows evidence of oxidation at low thermal maturity, a phenonemom not documented for kerogen. Bitumen maturation and degradation at higher thermal maturity is driven by cleavage and loss of aliphatic carbons, and is coincident with the maximum generation of oil and gas. The aromatic content of bitumen and of kerogen both increase during maturation as a consequence of the loss of aliphatic carbon. The oil and gas generation potential of the residual organic matter thus

The shell coal gasification process

Energy Technology Data Exchange (ETDEWEB)

Koenders, L.O.M.; Zuideveld, P.O. [Shell Internationale Petroleum Maatschappij B.V., The Hague (Netherlands)

1995-12-01

Future Integrated Coal Gasification Combined Cycle (ICGCC) power plants will have superior environmental performance and efficiency. The Shell Coal Gasification Process (SCGP) is a clean coal technology, which can convert a wide range of coals into clean syngas for high efficiency electricity generation in an ICGCC plant. SCGP flexibility has been demonstrated for high-rank bituminous coals to low rank lignites and petroleum coke, and the process is well suited for combined cycle power generation, resulting in efficiencies of 42 to 46% (LHV), depending on choice of coal and gas turbine efficiency. In the Netherlands, a 250 MWe coal gasification combined cycle plant based on Shell technology has been built by Demkolec, a development partnership of the Dutch Electricity Generating Board (N.V. Sep). The construction of the unit was completed end 1993 and is now followed by start-up and a 3 year demonstration period, after that the plant will be part of the Dutch electricity generating system.

The interaction between bitumen matrix and chemical components of radioactive wastes of WWER type

International Nuclear Information System (INIS)

Selucky, P.; Sazavsky, P.; Peka, V.; Krupka, M.

2000-01-01

The interaction between bitumen matrix and chemical components of WWER type radioactive wastes was studied. So called ''cold'' model bitumen products were prepared and compared with real products using macroDTA method. On the basis of obtained curves, the evaluation of bitumen product fire risks was performed with the aim to minimize risks of bituminization process. (authors)

Rheological, structural and chemical evolution of bitumen under gamma irradiation

International Nuclear Information System (INIS)

Mouazen, M.; Poulesquen, A.; Bart, F.; Masson, J.; Charlot, M.; Vergnes, B.

2013-01-01

Bitumen derived from crude oil by fractional distillation has been used in the nuclear industry as a radioactive waste encapsulation matrix. When subjected to α, β and γ self-irradiation, this organic matrix undergoes radiolysis, generating hydrogen bubbles and modifying the physical and chemical properties of the material. In this paper, the effects of irradiation on bitumen materials, especially in terms of its physical, chemical, structural and rheological properties, were characterized at radiation doses ranging from 1 to 7 MGy. An increase in the shear viscosity and melt yield stress was observed with increasing doses. Similarly, the elastic and viscous moduli (G' and G'') increase with the dose, with a more pronounced increase for G' that reflects enhanced elasticity arising from radiation-induced cross-linking. In addition, a low-frequency plateau is observed for G', reflecting pseudo-solid behavior and leading to an increase of the complex viscosity. This behavior is due to increased interactions between asphaltene particles, and to aromatization of the bitumen by γ-radiations. Cross-linking of bitumen enhances its strength, as confirmed by various techniques (modulated DSC, DTA/TGA, SEC, FTIR and XRD). (authors)

Improved cracking characteristics of bitumen through advanced froth treatment process

Energy Technology Data Exchange (ETDEWEB)

Ng, S.H. [National Centre for Upgrading Technology, Devon, AB (Canada); Dabros, T. [Natural Resources Canada, Devon, AB (Canada). CANMET Advanced Separation Technologies Laboratory; Humphries, A. [Albemarle Catalysts Co., Houston, TX (United States)

2006-07-01

Fluid catalytic cracking (FCC) is the dominant refinery conversion process for producing transportation fuels. Feed to the FCC unit is heavy gas oil (HGO). Its quality depends on the crude used and the processes involved. Bitumen-derived crude (BDC), including synthetic crude oil (SCO) is less superior to produce FCC feed than stocks from conventional sources. As a result, North American refiners have limited the use of BDC in their conventional FCC-based operations. This paper examined the improved cracking characteristics of bitumen through an advanced froth treatment process. This involved processing of the bitumen with paraffinic solvent in froth treatment with removal of some asphaltenes, CCR precursors, and metals. The paper discussed the experimental and subsequent results and discussion, including cracking characteristics; product quality; synergetic effect; and economic benefits. It was concluded that the poisoning effect by some deleterious components such as nitrogen compounds in feeds on the catalyst could be reduced or compensated for by higher C/O ratios (more catalyst per unit weight of feed). In addition, as conversion increased, sulfur in gasoline decreased slightly and linearly with more or less the same magnitude for the two bitumens. 5 refs., 1 tab., 3 figs.

In-situ water vaporization improves bitumen production during electrothermal processes

Energy Technology Data Exchange (ETDEWEB)

Wang, J. [Calgary Univ., AB (Canada); McGee, B. [E-T Energy, Calgary, AB (Canada); Kantzas, A. [Calgary Univ., AB (Canada). Tomographic Imaging and Porous Media Laboratory

2008-10-15

Electro-thermal processes are now being considered as an alternative or complementary process to steam injection processes. This study used an in situ vaporized water process to optimize electrothermal processes for steam injection enhanced oil recovery (EOR). A simulation tool was used to model electro-thermal processes in an Athabasca oil sands reservoir. Incremental oil recovery was estimated based on a 3-block conceptual model. A field scale model was then used to investigate the effects of electrode spacing, water injection rates, and electrical heating rates on bitumen recovery. Results of the simulation studies were then analyzed using a statistical tool in order to determine optimal conditions for maximizing bitumen production. Results of the study showed that incremental recovery using the water vaporization technique resulted in oil recovery rates of 25 per cent original oil in place (OOIP). Sensitivity analyses showed that medium electrical heating rates, low water injection rates, and small spacings between electrodes maximized bitumen production rates. It was concluded that the technique can be used alone or combined with other methods to economically produce bitumens. 2 refs., 7 tabs., 9 figs.

Modified bitumen for embedding of radioactive wastes

International Nuclear Information System (INIS)

Bozkurt, C.

1984-11-01

This work describes new possibilities of using polymer modified bitumen as matrix material for embedding of low- and medium level radioactive wastes. Epoxy resins, polyurethane resins and styrene-butadiene-copolymers with 20-40 weight per cent are used as modifying agents. Penetration and softening point (ring and ball) of modified samples have been measured. Further the resistance to toluene and leaching rate in n-heptane have been determined. Within these polymer bitumen combinations investigated, the epoxy resins having a high epoxid equivalent weight with dicarbooxylic acid anhydrid hardeners and tertiary amin accelerators give the most dense network, highest thermodimensional stability and lowest leaching rate in organic solvents. 71 refs., 9 figs., 6 tabs

The USA on the way to the post-petroleum era?

International Nuclear Information System (INIS)

Anon.

2007-01-01

Even if not self-sufficient, the USA have important energy resources at their disposal. At the second rank for natural gas and coal production, they are at the third position for petroleum. However, on the reserves side, their position falls down to the seventh position for gas and to the tenth position for petroleum. The US energy balance is thus very precarious with a constant decay of the national oil production since more than 30 years (-50%) and a stagnation of gas production over the same period. Renewable energies represent more than 150 million tons of petroleum equivalent and the US energy consumption is growing up with an average rate of 1.3%. Therefore, political energy choices are of prime importance. This article make a brief status of the US energy scene, from coal to hydrogen, and presents the US initiatives in this domain: diversification of the energy offer, re-launching of atomic energy, investment in the hydrogen economy, development of carbon sequestration technologies, capture and recycling of methane effluents and R and D efforts on biofuels. (J.S.)

Assessment of alternative management techniques of tank bottom petroleum sludge in Oman

International Nuclear Information System (INIS)

Al-Futaisi, Ahmed; Jamrah, Ahmad; Yaghi, Basma; Taha, Ramzi

2007-01-01

This paper investigated several options for environmentally acceptable management techniques of tank bottom oily sludge. In particular, we tested the applicability of managing the sludge by three options: (1) as a fuel supplement; (2) in solidification; (3) as a road material. Environmental testing included determination of heavy metals concentration; toxic organics concentration and radiological properties. The assessment of tank bottom sludge as a fuel supplement included various properties such as proximate analysis, ultimate analysis and energy content. Solidified sludge mixtures and road application sludge mixtures were subjected to leaching using the toxicity characteristic leaching procedure (TCLP). Tank bottom sludge was characterized as having higher concentrations of lead, zinc, and mercury, but lower concentrations of nickel, copper and chromium in comparison with values reported in the literature. Natural occurring radioactive minerals (NORM) activity values obtained on different sludge samples were very low or negligible compared to a NORM standard value of 100 Bq/g. The fuel assessment results indicate that the heating values, the carbon content and the ash content of the sludge samples are comparable with bituminous coal, sewage sludge, meat and bone meal and petroleum coke/coal mixture, but lower than those in car tyres and petroleum coke. The nitrogen content is lower than those fuels mentioned above, while the sulfur content seems comparable with bituminous coal, petroleum coke and a petroleum coke/coal mixture. The apparent lack of leachability of metals from solidification and road material sludge applications suggests that toxic metals and organics introduced to these applications are not readily attacked by weak acid solutions and would not be expected to migrate or dissolved into the water. Thus, in-terms of trace metals and organics, the suggested sludge applications would not be considered hazardous as defined by the TCLP leaching procedure

Effect of black rice husk ash on the physical and rheological properties of bitumen

Science.gov (United States)

Romastarika, Raissa; Jaya, Ramadhansyah Putra; Yaacob, Haryati; Nazri, Fadzli Mohamed; Agussabti, Ichwana, Jayanti, Dewi Sri

2017-08-01

Black rice husk ash (BRHA) waste product is inexpensive and can be obtained from rice mills. Reuse of waste product is ideal to reduce pollution, because disposal is decreased or eliminated. The commercial value of BRHA has increased, and it is suitable for use in road construction. In this study, BRHA waste was ground using a grinding ball mill for 120 min to form fine powder. BRHA was then sieved to less than 75 µm. At the laboratory, BRHA was mixed with bitumen to replace 2%, 4%, and 6% of the total weight, whereas 0% represented the control sample. The penetration, softening point, dynamic shear rheometer (DSR) and rolling thin film oven (RTFO) were investigated in this study. Results showed that bitumen became harder, whereas the rate of penetration decreased when the replacement amount of BRHA increased. Softening point test of bitumen also revealed an increase. The short-term aging test revealed that modification of bitumen could relieve the effect of aging. BRHA waste added into bitumen improved the performance of bitumen. Therefore, the usage of BRHA could help improve the performance of road pavement and reduce the rutting effect.

Evaluation of bitumen-rubber asphalt manufactured from modified binder at lower viscosity

CSIR Research Space (South Africa)

O'Connell, Johannes S

2010-08-01

Full Text Available In South Africa, crumb tyre-modified bitumen commnly known as bitumen-rubber binder has viscosity limits specified by the current edition of TG1: The Use of Modified Bituminous Binders in Road Construction. As the crumb rubber is 'digested...

Study of the thermal and mechanical sensitivity of bitumen/oxygen salt mixtures

International Nuclear Information System (INIS)

Backof, E.; Diepold, W.

1975-07-01

The safe handling characteristics of radioactive wastes containing nitrate salts to be fixed in bitumen for ultimate storage in salt mines according to a process developed at the Karlsruhe Nuclear Research Center have been examined with respect to their combustibility and shock sensitivity in tests of inactive bitumen/salt mixtures. Samples containing 40% bitumen and 60% nitrates of alkali, alkaline earth, and heavy metals, organic acids and rare earths were used to determine the thermal sensitivity (ignition temperature, duration of burning, heating under contained conditions), the mechanical sensitivity (shock sensitivity) and, in order to simulate major shock stresses, the sensitivity against detonation stresses. A few basic experiments were also performed on some beta-irradiated inactive samples. It appeared that although the addition of nitrates increased the combustibility of bitumen, neither the high thermal nor the detonation stresses resulted in any explosion-type reaction. (orig.) [de

Environmental care in coal combustion

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

Kvaerner Power will supply a CYMIC{reg_sign} circulating fluidized bed (CFB) boiler with a 63 MW electricity capacity to Manitowoc Public Utilities, in Manitowoc, Wisconsin, USA in 2006. This boiler is designed to burn bituminous coal and petroleum coke, with minimised emissions of SO{sub 2} and NOx. Kvaerner Power CFBs are capable of burning either coal or biomass (eg paper pellets) in any combination. Recent deliveries, to Indonesia and China as well as the USA, are listed. 1 tab., 5 photos.

The influence of calcination on the physical and chemical properties of petroleum and mixed cokes

Energy Technology Data Exchange (ETDEWEB)

Sikora, K; Syrek, H

1980-01-01

Freshly prepared petroleum and coal-petroleum cokes, before utilization for the production of various materials, are subjected to calcining--thermal treatment in a neutral or reducing atmosphere without the admission of air at less than or equal to 1400/sup 0/. During calcining, stabilization of the physical and chemical properties of the cokes takes place. The properties of the obtained coke depend chiefly on the calcining time and temperature. During calcining, volatile substances are removed almost completely from the coke; the coke density is increased, and its structure is put in order; the electrical conductivity is improved; the mechanical strength is increased; and the reactivity of the coke is decreased. Laboratory studies were conducted on calcining mixed coal-petroleum cokes of two grades at 1200, 1250, and 1300/sup 0/ for 2-6 h. In the calcining products the content of volatile substances, the ash content, S content, and density were determined. It was ascertained that calcining of mixed coal-petroleum cokes goes analogously to calcining of pure petroleum cokes. Raising the temperature and increasing the time of calcining has a substantial effect on improvement of coke physical and chemical properties. For high-quality coke, calcining is to be carried out at greater than or equal to 1300/sup 0/ for 4-6 h, for ordinary coke at > 1200/sup 0/ and greater than or equal to 4 h. The results are regarded as starting data for an industrial study of the calcining process.

Far infrared (terahertz) spectroscopy of a series of polycyclic aromatic hydrocarbons and application to structure interpretation of asphaltenes and related compounds.

Science.gov (United States)

Cataldo, Franco; Angelini, Giancarlo; García-Hernández, D Aníbal; Manchado, Arturo

2013-07-01

A series of 33 different polycyclic aromatic hydrocarbons (PAHs) were studied by far infrared spectroscopy (terahertz spectroscopy) in the spectral range comprised between 600 and 50 cm(-1). In addition to common PAHs like naphthalene, anthracene, phenanthrene, fluoranthene, picene, pyrene, benzo[α]pyrene, and perylene, also quite unusual PAHs were studied like tetracene, pentacene, acenaphtene, acenaphtylene, triphenylene, and decacyclene. A series of alkylated naphthalenes and anthracenes were studied as well as methypyrene. Partially or totally hydrogenated PAHs were also object of the present investigation, ranging from tetrahydronaphthalene (tetralin) to decahydronaphthalene (decalin), 9,10-dihydroanthracene, 9,10-dihydrophenanthrene, hexahydropyrene, and dodecahydrotriphenylene. Finally, the large and quite rare PAHs coronene, quaterrylene, hexabenzocoronene, and dicoronylene were studied by far infrared spectroscopy. The resulting reference spectra were used in the interpretation of the chemical structure of asphaltenes (as extracted from a heavy petroleum fraction and from bitumen), the chemical structures of other petroleum fractions known as DAE (distillate aromatic extract) and RAE (residual aromatic extract), and a possible interpretation of components of the chemical structure of anthracite coal. Asphaltenes, heavy petroleum fractions, and coal were proposed as model compounds for the interpretation of the emission spectra of certain proto-planetary nebulae (PPNe) with a good matching in the mid infrared between the band pattern of the PPNe emission spectra and the spectra of these oil fractions or coal. Although this study was finalized in an astrochemical context, it may find application also in the petroleum and coal chemistry. Copyright © 2013 Elsevier B.V. All rights reserved.

Lessons learned from IOR steamflooding in a bitumen-light oil heterogeneous reservoir

NARCIS (Netherlands)

Al Mudhafar, W.J.M.; Hosseini Nasab, S.M.

2015-01-01

The Steamflooding was considered in this research to extract the discontinuous bitumen layers that are located at the oil-water contact for the heterogeneous light oil sandstone reservoir of South Rumaila Field. The reservoir heterogeneity and the bitumen layers impede water aquifer approaching into

Evaluation of bitumens for nuclear facilities radioactive waste immobilization

International Nuclear Information System (INIS)

Guzella, Marcia F.R.; Silva, Tania V. da; Loiola, Roberto; Monte, Lauro J.B.

2000-01-01

The activities developed at the Nuclear Technology Development Centre, Centro de Desenvolvimento da Tecnologia Nuclear - CDTN/CNEN, include the research and development work of the radioactive wastes immobilization in different kind of bitumen. The present work describes the bituminization of simulated low level wastes of evaporator concentrates.Two types of bitumen are used for incorporation of the simulated wastes generated by nuclear power plants. Studies on rheological properties, leaching data, differential thermoanalysis and water content of the waste-products have been carried out. (author)

Wetlands in Canada's western boreal forest: Agents of change

Energy Technology Data Exchange (ETDEWEB)

Foote, L.; Krogman, N. [University of Alberta, Edmonton, AB (Canada). Dept. of Renewable Resources

2006-11-15

Wetlands of the western boreal forest are poorly studied. In the last decade (1990-2000) there were approximately 1810 northern hemisphere scientific papers published addressing boreal wetlands, tundra, taiga, or bogs. We explore the extent of understanding and impacts of six major agents of change affecting forested wetlands of the boreal zone: (1) commercial forestry, (2) petroleum extraction, (3) mining (bitumen, coal, peat, ore, and diamonds), (4) agriculture, (5) climate change, and (6) hydrologic alteration. Finally, we address the social context, costs, and recommendations for wetland maintenance.

Petroleum and natural gas in Illinois

Energy Technology Data Exchange (ETDEWEB)

None

1979-01-01

Presentations made at the 7th Annual Illinois Energy Conference are compiled and reported. Specific topics include: Illinois petroleum and natural gas supply; energy use patterns for Illinois and the nation; impacts of the National Energy Act on the natural gas industry; natural gas for North America; natural gas supply under the Natural Gas Policy; US access to international oil; deregulation and its impact on the US petroleum supply; the US Energy Policy; petroleum pricing and taxation policies in Illinois; the high cost of energy and its impact on the poor; impact of increased fuel prices on Illinois' industrial future; energy prices and inflation; opportunities for energy conservation in transportaton; overview of energy and synfuels from biomass and wastes; an inventory of energy potential from biomass in Illinois; problems and potential of alcohol from agriculture; liquid and gaseous fuels from coal; and alternatives to liquid and gaseous fuels.

Mechanical Properties of Millet Husk Ash Bitumen Stabilized Soil Block

Directory of Open Access Journals (Sweden)

M. T. Abdulwahab

2017-06-01

Full Text Available This study presents an investigation into the improvement of strength and durability properties of lateritic soil blocks using Millet Husk Ash (MHA and Bitumen as additives so as to reduce its high cost and find alternative disposal method for agricultural waste. The lateritic soil samples were selected and treated with 0%, 10%, 15%, 20%, 30%, 40% and 50% of MHA by weight of laterite. The lateritic soil-MHA mixture was later admixed with 0%, 2%, 4%, 6%, 8%, 10%, 12% and 14% cut-back bitumen solution by weight of laterite. Both the natural lateritic soil, lateritic and MHA, and the blend of Soil, MHA and Bitumen were first subjected to physical and chemical analysis using X-Ray Fluorescence (XRF and Scanning Electromagnetic Machine (SEM to determine their engineering properties followed by the performance test on bricks cast with varying quantities of the additives. A total of one hundred and ninety two (192 cubes were tested for moisture absorption, erodability and compressive strength tests. The result of the test showed that MHA and Bitumen acted as pozzolana in performance test on the soil blocks. Up to 30% MHA – laterite and 20% MHA admixed with 8% laterite were found to give optimum compressive strength of 10.8N/mm2 and 10.9N/mm2 for the bricks produced. The result also showed that about 50% MHA blended with 14% Bitumen solution ensured water tight bricks. Thus the use of MHA as partial replacement of cement will provide an economic use of by-product and consequently produce a cheaper soil block construction without comprising its strength.

Fuel briquettes from brown coals of Yakutia

Energy Technology Data Exchange (ETDEWEB)

L.A. Nikolaeva; V.G. Latyshev; O.N. Burenina [Russian Academy of Sciences, Yakutsk (Russian Federation). Institute of Oil and Gas Problems

2009-04-15

Experimental data on the development of technology for the manufacture of briquetted fuel from brown coals with the use of various petroleum binders are presented. The influence of the moisture content, the coal particle-size composition, the binder type and concentration, the compacting pressure, and heat treatment regimes on the mechanical properties of the materials was studied. The optimal compositions and optimal values of the engineering parameters for the production of graded briquetted fuel from brown coals of the Kangalassy deposit in the Republic of Sakha (Yakutia) were established.

Electro-thermal dynamic stripping process : integrating environmentalism with bitumen production

Energy Technology Data Exchange (ETDEWEB)

McGee, B.C.W.; McDonald, C.W. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[E-T Energy, Calgary, AB (Canada); Little, L. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Alberta Energy Research Inst., Edmonton, AB (Canada)

2008-10-15

This paper presented a new method of in situ oil sands extraction developed by Calgary-based E-T Energy. The Electro-Thermal Dynamic Stripping Process (ET-DSP) uses electricity to melt oil sands deposits that are too deep for open pit mining. The energy intensity of production compares favourably with alternative thermal bitumen extraction techniques and water consumption for the process is comparatively low, with all produced water being re-injected into the producing formation without any treatment. With ET-DSP, electrodes are drilled and completed next to the oil sands formation which ensures that the electrical currents are forced to flow to the oil sands formation. The viscosity of the bitumen is lowered by the heat from the current, thereby making the fluid flow more readily into vertical extraction wells. ET-DSP uses electricity directly from the power grid, and does not produce any greenhouse gas (GHG) emissions of its own. The process has the potential to allow operators to focus on areas of oil sands reservoirs that have remained inaccessible. Field studies confirmed that the production of bitumen using this method was achieved with reduced greenhouse gas emissions as compared to other thermal recovery process. The bitumen had trace amount of sand and no emulsions. 5 refs., 5 figs.

Liquid fuels from Canadian coals

Energy Technology Data Exchange (ETDEWEB)

Taylor, G. W.

1979-06-15

In Canadian energy planning, the central issue of security of supply must be addressed by developing flexible energy systems that make the best possible use of available resources. For liquid fuel production, oil sands and heavy oil currently appear more attractive than coal or biomass as alternatives to conventional crude oil, but the magnitude of their economic advantage is uncertain. The existence of large resources of oil sands, heavy oils, natural gas and low-sulfur coals in Western Canada creates a unique opportunity for Canadians to optimize the yield from these resources and develop new technology. Many variations on the three basic liquefaction routes - hydroliquefaction, pyrolysis and synthesis - are under investigation around the world, and the technology is advancing rapidly. Each process has merit under certain circumstances. Surface-mineable subbituminous and lignite coals of Alberta and Saskatchewan appear to offer the best combination of favorable properties, deposit size and mining cost, but other deposits in Alberta, Nova Scotia and British Columbia should not be ruled out. The research effort in Canada is small by world standards, but it is unlikely that technology could be imported that is ideally suited to Canadian conditions. Importing technology is undesirable: innovation or process modification to suit Canadian coals and markets is preferred; coprocessing of coal liquids with bitumen or heavy oils would be a uniquely Canadian, exportable technology. The cost of synthetic crude from coal in Canada is uncertain, estimates ranging from $113 to $220/m/sup 3/ ($18 to $35/bbl). Existing economic evaluations vary widely depending on assumptions, and can be misleading. Product quality is an important consideration.

[Design of coal stove, construction, assembly and test

International Nuclear Information System (INIS)

Bitrus, K.D.; Dauda, S.

2004-01-01

Some years back, after the discovery of Petroleum, Kerosene as one of the fraction of the distillation of Petroleum came into use as cooking fuel and a reduction in pressure was seen on wood and vegetation. Along this line, by the improvement of sciences and technology gas cooker and electric cooker were developed; but epileptic supply of electricity, gas and government policy on deforestation showed that continuous dependence on wood, electricity, gas and kerosene as the only sources of cooking fuel is not going to solve Nigeria domestic cooking problem. To solve this, coal as a source of heat energy could be used as a cooking fuel. However, this paper reports the design of coal stove, construction, assembly and test. The test result showed that using coal (anthracite) as the fuel on a pot of 200g containing 800g of water at room temperature could boil the water in 20 minutes

Process for refining shale bitumen

Energy Technology Data Exchange (ETDEWEB)

Plauson, H

1920-09-19

A process is disclosed for refining shale bitumen for use as heavy mineral oil, characterized by mixtures of blown hard shale pitch and heavy mineral oil being blown with hot air at temperatures of 120 to 150/sup 0/ with 1 to 3 percent sulfur, and if necessary with 0.5 to 3 percent of an aldehyde.

Did you know? Petroleum industry fast facts: British Columbia

International Nuclear Information System (INIS)

1999-10-01

This is part of a series of brochures published by the Petroleum Communication Foundation, a non-profit society established in 1975. The foundation's objective is to stimulate public awareness and understanding of Canada's petroleum industry and its contribution to the economy of each of the provinces where the industry's presence and impact is substantial. This brochure provides brief, but useful, information about British Columbia, about its area (947,800 sq.km), capital (Victoria), population (4.009,922 in 1998), major industries (forestry, wood and paper, petroleum and mining, tourism, agriculture, fishing, manufacturing), revenue from natural resources ($ 350 million from oil and natural gas in 1998-1999, or about 20 per cent of total provincial government revenues), some facts about the petroleum industry in British Columbia, (production, employment, pipelines, etc.), major exports (wood products, pulp and paper products, machinery and equipment, coal, petroleum products, electricity) and upstream industry expenditures in British Columbia (in excess of $ 1 billion). map, pie-chart, figs

Biological marker distribution in coexisting kerogen, bitumen and asphaltenes in Monterey Formation diatomite, California

Science.gov (United States)

Tannenbaum, E.; Ruth, E.; Huizinga, B. J.; Kaplan, I. R.

1986-01-01

Organic-rich (18.2%) Monterey Formation diatomite from California was studied. The organic matter consist of 94% bitumen and 6% kerogen. Biological markers from the bitumen and from pyrolysates of the coexisting asphaltenes and kerogen were analyzed in order to elucidate the relationship between the various fractions of the organic matter. While 17 alpha(H), 18 alpha(H), 21 alpha(H)-28,30-bisnorhopane was present in the bitumen and in the pryolysate of the asphaltenes, it was not detected in the pyrolysates of the kerogen. A C40-isoprenoid with "head to head" linkage, however, was present in pyrolysates of both kerogen and asphaltenes, but not in the bitumen from the diatomite. The maturation level of the bitumen, based on the extent of isomerization of steranes and hopanes, was that of a mature oil, whereas the pyrolysate from the kerogen showed a considerably lower maturation level. These relationships indicate that the bitumen may not be indigenous to the diatomite and that it is a mature oil that migrated into the rock. We consider the possibility, however, that some of the 28,30-bisnorhopane-rich Monterey Formation oils have not been generated through thermal degradation of kerogen, but have been expelled from the source rock at an early stage of diagenesis.

Coal: a revival for France?

International Nuclear Information System (INIS)

Brones, W.

2007-01-01

All energy consumption forecasts indicate a world production peak of fossil fuels around 2030 followed by a rapid decline. The oil peak should probably occur earlier. In this context the huge worldwide reserves of coal represent a fantastic opportunity to meet the world power demand which should double between 2002 and 2030 with in particular a huge growth in China and India. If promising alternate technologies (coal liquefaction..) exist which would allow to replace petroleum by coal, the main question remains the management of CO 2 . Capture and sequestration techniques are already implemented and tested and the search for new coal deposits is going on, in particular in France in the Nievre area. Economic studies about the profitability of coal exploitation in France stress on the socio-economical advantage that a revival of this activity would represent, in particular in terms of employment. (J.S.)

Bioremediation of petroleum hydrocarbons in soil environments

International Nuclear Information System (INIS)

Rowell, M.J.; Ashworth, J.; Qureshi, A.A.

1992-12-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed via a literature survey and discussions with workers in relevant disciplines. The impacts of hydrocarbons on soil are discussed along with a range of methods available to assist in their decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, sludges, asphalts and bitumens, drilling mud residues, creosote tars, and some pesticides. The degradability of hydrocarbons largely depends upon their aqueous solubility and their adsorption on soil surfaces and, therefore, is related to their molecular structures. The ease of decomposition decreases with increasing complexity of structure, in the order aliphatics > aromatics > heterocyclics and asphaltenes (most recalcitrant). Most soils contain an adequate population of microorganisms and hence bioaugmentation may only be needed in special circumstances. Decomposition is fastest in soils where the hydrocarbon loading rate, aeration, nutrition, moisture, and pH are all optimized. At spill sites there is little control over the application rate, although containment measures can assist in either limiting contamination or distributing it more evenly. The enhancement of bioremediation is discussed in light of all these factors. Other techniques such as enhanced aeration, hydrocarbon decomposition by anaerobic processes, surfactants, and burning are also discussed. 211 refs., 11 figs., 10 tabs

Bioremediation of petroleum hydrocarbons in soil environments

Energy Technology Data Exchange (ETDEWEB)

Rowell, M J; Ashworth, J; Qureshi, A A

1992-12-01

The bioremediation of petroleum hydrocarbons in soil environments was reviewed via a literature survey and discussions with workers in relevant disciplines. The impacts of hydrocarbons on soil are discussed along with a range of methods available to assist in their decomposition by soil microorganisms. The range of petroleum-based materials considered includes conventional and synthetic crude oils, refined oils, sludges, asphalts and bitumens, drilling mud residues, creosote tars, and some pesticides. The degradability of hydrocarbons largely depends upon their aqueous solubility and their adsorption on soil surfaces and, therefore, is related to their molecular structures. The ease of decomposition decreases with increasing complexity of structure, in the order aliphatics > aromatics > heterocyclics and asphaltenes (most recalcitrant). Most soils contain an adequate population of microorganisms and hence bioaugmentation may only be needed in special circumstances. Decomposition is fastest in soils where the hydrocarbon loading rate, aeration, nutrition, moisture, and pH are all optimized. At spill sites there is little control over the application rate, although containment measures can assist in either limiting contamination or distributing it more evenly. The enhancement of bioremediation is discussed in light of all these factors. Other techniques such as enhanced aeration, hydrocarbon decomposition by anaerobic processes, surfactants, and burning are also discussed. 211 refs., 11 figs., 10 tabs.

A source mixing model to apportion PAHs from coal tar and asphalt binders in street pavements and urban aquatic sediments

Energy Technology Data Exchange (ETDEWEB)

Ahrens, M.J.; Depree, C.V. [National Institute of Water & Atmospheric Research, Hamilton (New Zealand)

2010-12-15

Present-day and more than 30 years old road and footpath pavements from Auckland, New Zealand were analysed for PAHs to test the hypothesis that coal tar based pavement binders contribute to unusually high PAH concentrations in adjacent stream and estuarine sediments Total PAH ({Sigma}{sub 28}PAH) concentrations in the dichloromethane-soluble fraction ('binder'), comprising 5-10% of pavement mass, were as high as 200 000 mg kg{sup -1}(10 000 mg kg{sup -1} in binder + aggregate) Older and deeper pavement layers were strongly pyrogenic, whereas pavement layers from recently sealed roads had a more petrogenic composition and more than 1000 times lower Sigma(28)PAH concentrations. Source identification analysis using three PAH isomer ratio pairs (benz(a)anthracene/(benz(a)anthracene + chrysene), benzo(a)pyrene/(benzo(a)pyrene + benzo(e)pyrene)), and indeno(1,2,3-cd)pyrene/(indeno(1,2,3-cd)pyrene + benzo(g,h,i)perylene) revealed low PAH (bitumen) pavements to have consistently lower isomer ratios than high PAH (coal tar) samples. A concentration-weighted mixing model, with coal tar and bitumen as source materials, explained more than 80% of the variance in isomer ratios and enveloped the entire PAH compositional and concentration range encountered PAH composition and concentrations in adjacent stream sediments ({gt} 15 mg kg{sup -1} dry weight) were consistent with diluted coal tar material as a principal PAH source. Due to the very high PAH concentrations of coal tar, a coal tar content of as little as 0.01% of total sediment mass can account for more than 90% of PAH concentrations in adjacent stream sediments.

Distribution and Thermal Maturity of Devonian Carbonate Reservoir Solid Bitumen in Desheng Area of Guizhong Depression, South China

Directory of Open Access Journals (Sweden)

Yuguang Hou

2017-01-01

Full Text Available The distribution of solid bitumen in the Devonian carbonate reservoir from well Desheng 1, Guizhong Depression, was investigated by optical microscope and hydrocarbon inclusions analysis. Vb and chemical structure indexes measured by bitumen reflectance, laser Raman microprobe (LRM, and Fourier transform infrared spectroscopy (FTIR were carried out to determine the thermal maturity of solid bitumen. Based on the solid bitumen thermal maturity, the burial and thermal maturity history of Devonian carbonate reservoir were reconstructed by basin modeling. The results indicate that the fractures and fracture-related dissolution pores are the main storage space for the solid bitumen. The equivalent vitrinite reflectance of solid bitumen ranges from 3.42% to 4.43% converted by Vb (% and LRM. The infrared spectroscopy analysis suggests that there are no aliphatic chains detected in the solid bitumen which is rich in aromatics C=C chains (1431–1440 cm−1. The results of Vb (%, LRM, and FTIR analysis demonstrate that the solid bitumen has experienced high temperature and evolved to the residual carbonaceous stage. The thermal evolution of Devonian reservoirs had experienced four stages. The Devonian reservoirs reached the highest reservoir temperature 210–260°C during the second rapid burial-warming stage, which is the main period for the solid bitumen formation.

Coal rank (vitrinite reflectance) data for Cretaceous/Tertiary coal measures in the Grande Cache and Hinton areas, Alberta

Energy Technology Data Exchange (ETDEWEB)

Kalkreuth, W.D.; Langenberg, W.; McMechan, M.E.; Tomica, M.A.; McDougall, W.; Burchard, K.

1996-07-01

A total of 544 vitrinite reflectance values are reported. The outcrop locations and other pertinent data are listed. Vitrinite reflectances determined in subsurface samples from two coal exploration boreholes and 13 petroleum exploration wells are tabulated. The data have been used (in other studies) to evaluate maturation levels in potential source rocks and to assess methane potential of the coal deposits. A diskette containing the data is included. 18 refs., 1 fig., 2 tabs.

Proceedings of the 5. NCUT upgrading and refining conference 2009 : bitumen, synthetic crude oil and heavy oil

International Nuclear Information System (INIS)

2009-01-01

This conference examined various upgrading technologies related to bitumen production. It provided a forum to review new developments to exploit oil sands bitumen and extra heavy crudes in terms of production, upgrading and environmental issues facing the industry. This 2009 conference focused on the many existing and emerging technical solutions that will help consolidate the position of the vast reserves in Western Canada as a sustainable source of crudes for North America and other selected markets. Some of the technical challenges that have an effect on upgrading include poor quality bitumen and heavy oils; bitumen and diluent blending; pipeline issues; desalting; fouling and corrosion; high costs; dependence on natural gas for energy; poor middle distillates; and greenhouse gas emissions. The sessions of the conference were entitled: heavy oil and bitumen upgrading technologies; secondary upgrading and refining technologies; bitumen transportation; and bitumen and heavy oil processability. The conference featured a total of 50 presentations and posters, of which 43 have been catalogued separately for inclusion in this database. tabs., figs

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline E. Burgess Clifford; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2006-05-17

This report summarizes the accomplishments toward project goals during the first six months of the third year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts, acquisition and installation of a research gasoline engine, and modification of diesel engines for use in evaluating diesel produced in the project. Characterization of the gasoline fuel indicates a dominance of single ring alkylcycloalkanes that have a low octane rating; however, blends containing these compounds do not have a negative effect upon gasoline when blended in refinery gasoline streams. Characterization of the diesel fuel indicates a dominance of 3-ring aromatics that have a low cetane value; however, these compounds do not have a negative effect upon diesel when blended in refinery diesel streams. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Combustion and characterization of fuel oil indicates that the fuel is somewhere in between a No. 4 and a No. 6 fuel oil. Emission testing indicates the fuel burns similarly to these two fuels, but trace metals for the coal-based material are different than petroleum-based fuel oils. Co-coking studies using cleaned coal are highly reproducible in the pilot-scale delayed coker. Evaluation of the coke by Alcoa, Inc. indicated that while the coke produced is of very good quality, the metals content of the carbon is still high in iron and silica. Coke is being evaluated for other possible uses

Ranking oil sands bitumen recovery techniques

Energy Technology Data Exchange (ETDEWEB)

Lam, A.; Nobes, D.S.; Lipsett, M.G. [Alberta Univ., Edmonton, AB (Canada). Dept. of Mechanical Engineering

2009-07-01

The preference ranking organization method (PROMETHEE) was used to assess and rank 3 techniques for in situ bitumen recovery: (1) steam assisted gravity drainage; (2) vapour extraction (VAPEX); and (3) toe-to-heel air injection (THAI). The study used a business scenario where management-type indicators included potential production rates; estimated overall operating costs; energy consumption; facilities requirement; recovery efficiency; and energy loss. Amounts of carbon dioxide (CO{sub 2}) emissions were also considered, as well as the production depth, formation thickness, and API gravity of the produced bitumen. The study showed that THAI recovery methods had the most beneficial criteria weighting of the 3 processes, while SAGD was the least favourable choice. However, SAGD processes are the most widely used of the 3 processes, while THAI has only been demonstrated on a limited scale. It was concluded that the maturity of a technology should be weighted more heavily when using the PROMETHEE method. 8 refs., 2 tabs.

Effects of operating conditions on compositional characteristics and reaction kinetics of liquid derived by delayed coking of nigerian petroleum residue

Directory of Open Access Journals (Sweden)

O. O. Bello

2006-09-01

Full Text Available The thermal upgrading of Nigerian petroleum residue was studied at relatively low pressure in a delayed coking reactor system. In this work, the intent was to investigate the effects of process variables such as reaction temperature (200(0C to 600(0C, reaction time (0 to 120min, additive concentration loading and additive-to-residue ratio on the amounts and quality of organic liquid product (OLP. The liquid products derived from the delayed coking process were characterized by means of instrumental analysis of gas-liquid chromatography. Results obtained from the analyses of the OLP revealed an upward trend of the conversion process and the selectivity of the aromatic compounds with additive-to-residue ratio (ARR and increase in temperature. This led to maximum yield of 37.2% achieved with ARR of 5 compared to 31% achieved with ordinary thermal conversion. The selectivity for aromatic hydrocarbons was maximum at 83.1wt% the selectivity towards aromatics and aliphatic hydrocarbons were highest for methanol-potassium hydroxide and methanol respectively. In all additive system cases, maximum OLP was produced at an optimum reaction temperature of 370(0C in the delayed coking reactor and at higher residence time. The gaseous product consisted of carbon monoxide and carbon dioxide and C1 - C6 hydrocarbons, which amounted to about 20 to 30 wt% of liquid distillate. The information obtained in this study show that the organic liquid products are amenable to characterization procedure and provided the basis for the identification of processes for upgrading Nigerian petroleum residue and such other starting materials such as bitumen or fossil fuel coal liquids.

Move on up-grading : if the oilsands are going to compete as a source of energy in the 21. century, then a whole new range of upgrading technologies must lead the way

Energy Technology Data Exchange (ETDEWEB)

Cope, G.

2008-12-15

Continued expansion of the oilsands in northeastern Alberta is facing challenges such as rising costs, water restrictions, depleting natural gas and environmental impacts. New efficient, cost effective and environmentally sound ways of producing and refining bitumen are needed. The Alberta Energy Research Institute's vision for Alberta is to become a world leader in commercializing new technologies to utilize heavy hydrocarbons with positive economic, social and environmental impact. Its Hydrocarbon Upgrading Demonstration Program (HUDP) is a new initiative to work in partnership with industry to develop the next generation of upgrading technologies and to quickly bring them to the commercial stage. AERI screened 100 different inceptive heavy oil technologies to pick the ones with breakthrough potential. This article described the 8 technologies that were selected as candidates. The 3 candidates in residue upgrading technology were ETX Systems which will test a new type of cross-flow coker that converts bitumen to lighter products; UOP which will advance the design of slurry phase hydrocracking; and, a solvent deasphalting process based on new concepts developed in phase 1 of HUDP. The 3 candidates in gasification technology were Pratt and Whitney Rocketdyne's advanced gasifier in which a rocket engine converts coal and bitumen byproducts into hydrogen and electricity; GreatPoint Energy which will test a catalytic gasification technology to convert petroleum coke and coal to synthetic natural gas (methane) in a single step; and Alter Nrg which will build a plasma gasification plant to produce electricity and chemicals from biomass and waste feedstock. The candidate for bitumen-to-petrochemicals technology was NOVA Chemicals which will scale up patented technology that converts bitumen fractions into petrochemical feedstocks. OPTI was selected as the candidate for carbon dioxide (CO{sub 2}) capture technology from the Long Lake oilsands plant. 6 refs., 3

Black out - The post-petroleum era has started

International Nuclear Information System (INIS)

Enderlin, S.

2009-01-01

The predictable shortage of petroleum resources raises up some worrying questions: how can we get rid of petroleum? What will be our life without petroleum? Will we have enough energy tomorrow to keep the same way of life as today? With what new energy sources tomorrow's world will turn? The author has travelled the world from the Americas to Asia and from Europe to the Persian Gulf to find the leads of the after-petroleum era. From the Chinese coal to the US ethanol, from the nuclear comeback to the Scandinavian innovations, this inquiry makes the world tour of projects, ideas and solutions. First world energy consumer and squanderer, the US hold a prominent place in the energy revolution that Barack Obama election will speed up. In Europe, Germany, Spain and Denmark have taken a serious lead in the green energies race, while China has become recently the first world power of greenhouse gas emissions. (J.S.)

Direct liquefaction of low-rank coals under mild conditions

Energy Technology Data Exchange (ETDEWEB)

Braun, N.; Rinaldi, R. [Max-Planck-Institut fuer Kohlenforschung, Muelheim an der Ruhr (Germany)

2013-11-01

Due to decreasing of petroleum reserves, direct coal liquefaction is attracting renewed interest as an alternative process to produce liquid fuels. The combination of hydrogen peroxide and coal is not a new one. In the early 1980, Vasilakos and Clinton described a procedure for desulfurization by leaching coal with solutions of sulphuric acid/H{sub 2}O{sub 2}. But so far, H{sub 2}O{sub 2} has never been ascribed a major role in coal liquefaction. Herein, we describe a novel approach for liquefying low-rank coals using a solution of H{sub 2}O{sub 2} in presence of a soluble non-transition metal catalyst. (orig.)

Late Cretaceous coal overlying karstic bauxite deposits in the Parnassus-Ghiona Unit, Central Greece: Coal characteristics and depositional environment

Energy Technology Data Exchange (ETDEWEB)

Kalaitzidis, Stavros; Siavalas, George; Christanis, Kimon [Dept. of Geology, University of Patras, 26504 Rio-Patras (Greece); Skarpelis, Nikos [Dept. of Geology and Geoenvironment, University of Athens, 15784 Zografou (Greece); Araujo, Carla Viviane [Petrobras-Cenpes GEOQ/PDEXP, Rua Horacio Macedo n 950, Cidade Universitaria - Ilha do Fundao, 21941-915 Rio de Janeiro (Brazil)

2010-04-01

The Pera-Lakkos coal located on top of bauxite deposits in the Ghiona mining district (Central Greece), is the only known Mesozoic (Late Cretaceous) coal in the country. It was derived from herbaceous plants and algae growing in mildly brackish mires that formed behind a barrier system during a regression of the sea, on a karstified limestone partly filled in with bauxitic detritus. Petrological, mineralogical and geochemical data point to the predominance of reducing conditions and intense organic matter degradation in the palaeomires. O/C vs. H/C and OI vs. HI plots, based on elemental analysis and Rock-Eval data, characterize kerogen types I/II. This reflects the relatively high liptinite content of the coal. Besides kerogen composition, O/C vs. H/C plot for the Pera-Lakkos coals is in accordance with a catagenesis stage of maturation in contrast with vitrinite reflectance and T{sub max} from Rock-Eval pyrolysis, which indicate the onset of oil window maturation stage. Suppression of vitrinite reflectance should be considered and the high liptinite content corroborates this hypothesis. Despite some favourable aspects for petroleum generation presented by the Pera-Lakkos coal, its maximum thickness (up to 50 cm) points to a restricted potential for petroleum generation. Coal oxidation took place either during the late stage of peat formation, due to wave action accompanying the subsequent marine transgression, or epigenetically after the emergence of the whole sequence due to percolation of drainage waters. Both options are also supported by the REE shale-normalized profiles, which demonstrate an upwards depletion in the coal layer. Oxidation also affected pyrite included in the coal; this led to the formation of acidic (sulfate-rich) solutions, which percolated downwards resulting in bleaching of the upper part of the underlying bauxite. (author)

Increased petroleum and natural gas dependence between Europe and the Arab Countries. What is the role for the states?

International Nuclear Information System (INIS)

Sarkis, N.

1995-01-01

This work deals with the increased petroleum and natural gas dependence between Europe and the Arab Countries. The euro-arabian relations and the worldwide energetic market perspectives are indicated as well as the petroleum, natural gas and coal prices between the years 1990 and 2010, the worldwide petroleum supply and demand estimations between 1994 and 2010 and the petroleum estimations between 1994 and 2010. (O.L.). 7 tabs

The new deal of coal

International Nuclear Information System (INIS)

Kalaydjian, F.; Cornot-Gandolphe, S.

2008-01-01

While coal appears as an inescapable resource to answer the energy needs of the 21. century, its highly CO 2 emitting combustion represents a major risk with respect to the requirements of the fight against climate change. In the first part of this book, the basic aspects of energy markets are explained and in particular the role that coal is going to play in the world's energy supplies. In the second part, the new coal usages are presented, which, combined with CO 2 capture and sequestration techniques, should allow to conciliate a massive use of coal and the respect of environmental constraints. This book is based on the works presented in February 2008 by the French institute of petroleum (IFP) about the new outlets of coal and the risks for climate change. Content: 1 - coal, energy of the 21. century: abundant and well distributed reserves; growing up world production; exponential world demand; international trade: still limited but in full expansion; 2 - Technologies for a CO 2 -free coal: CO 2 capture and sequestration technologies; towards poly-generation; production of coal-derived liquid fuels; 3 - Appendices: coals formation; coal in China: status and perspectives; coal in the USA: status and perspectives; coal in India: status and perspectives; COACH: an ambitious European project; CBM - E-CBM, status and perspectives. (J.S.)

Meeting of Commission of International Committee on Petrology of Coals

Energy Technology Data Exchange (ETDEWEB)

Timofeev, P P; Bogolyubova, L I

1982-03-01

In Urbana, Illinois from 18-20 May 1979 the XXXII session of the International Committee on Petrology met. Reports were made on standards for the study of bituminous and anthracite coals. Use of reflective capacity of vitrain to determine coalification of coals was discussed along with a proposition to establish numerical boundaries between brown, bituminous and anthracite coals. The re-editing of the International Dictionary on Petrology of Coals was agreed upon in view of new facts on microcomponents of coal and methods of studying them. The next meeting of the Commission took place at Ostrav, Czechoslovakia from 14-26 April 1980. At the plenary session, new officials were elected and agreement to re-edit the Dictionary on Petrology of Coals was confirmed. At the meeting of the Commission on Coal Petrography the question of the determination of components of coal by quantitative diagnosis, and results of determining components of vitrain by measuring its reflective capacity were reported on. At the meeting of the Committee on Applying Facts of Petrology in Geology, the classification of solid oil bitumen and organic substance of sediments was discussed. At the meeting of the Committee on the Application of the Petrology of Coals in Industry, attention was given to discussing basic parameters for the international classification of coals to be presented at the meeting of the Economic Commission of Europe in Geneva. In the final plenary session of the commission, results of discussions were summarized. The next session was to be held in France in 1981. (In Russian)

Methanol from coal without CO2 production via the modular high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Schleicher, R.W. Jr.; Engler, D.; Labar, M.P.

1992-01-01

Displacement options for petroleum fuels include natural gas (compressed or liquified), synthetic gasoline, biomass fuels, electric vehicles, hydrogen, and methanol. This paper reports that although no alternative meets all the desired characteristics of economics, environmental impact, supply logistics, and vehicle technology, methanol has often been cited as a good compromise and is perhaps the best coal derived fuel. The main criticism leveled at methanol is whether it can be produced economically in sufficient quantities to significantly displace petroleum-derived fuels. Although methanol can be manufactured from biomass, natural gas or coal feedstocks, only coal offers the potential for a substantial long term indigenous U.S. feedstock

Effects of SBS Configuration on Performance of High Modulus Bitumen Based on Dynamic Mechanical Analysis

Directory of Open Access Journals (Sweden)

Ming Liang

2016-07-01

Full Text Available High modulus bitumens modified by polystyrene-block-polybutadiene-block-polystyrene (SBS with different molecular structure were investigated on dynamic shear rheometer and fluorescence microscopy to evaluate viscoelastic properties and morphology of binders. The results shows that storage modulus (G’ is obviously less than loss modulus (G”, which means viscous behaviour of bitumen is dominant, and anti-rutting factor (G* ⁄ sin δ is markedly enhanced by star SBS than by linear SBS. The morphology indicated that star SBS improved the softening point more obviously, tending to form a cross-linked network in bitumen. As for linear SBS, it is dispersed in bitumen in the form of globules and enhances the ductility of binder.

On the determination of diffusivities of volatile hydrocarbons in semi-solid bitumen

International Nuclear Information System (INIS)

Tang, J. S.

2001-01-01

Carbon dioxide, supercritical ethane and propane have been considered as solvents to recover heavy oil. Given that mixing solvent with bitumen is one of the important parameters governing the performance of the solvent extraction processes, good understanding of solvent dispersion is essential for the proper design of the process. Produced bitumen can still contain some residual volatile hydrocarbons after gas flashing off a three-phase separator. When exposed to the air due to a spill or ruptured line, these residual hydrocarbons can escape and create air pollution problems. Consequently, knowledge of the diffusivities of volatile components in bitumen is needed to assess the extent of environmental damage that may result from bitumen spill or working loss of vapour to the atmosphere. This paper discusses the de-coupled transfer model developed by this author (and described in a paper in vol. 78 of this journal) and its limiting solution, and provides a re-intrepretation of the method by Fu and Phillips (1979) which in turn was based on the late-time limiting solution advanced by Tang and Zhang (2000). The analysis indicates that gas purging is a valid method for determining the diffusion coefficients of trace, volatile hydrocarbons in bitumen. However, the assumption of de-coupling may not be appropriate for large diffusion flux and slow gas flow. Furthermore, improper use of the limiting solution theory could lead to a 25 per cent error in calculating the diffusion coefficient. 14 refs., 2 tabs., 8 figs

European Model Code of safe practice in the storage and handling of petroleum products. Part I. Operations

Energy Technology Data Exchange (ETDEWEB)

1973-01-01

This safe practice code was prepared by a working group consisting of experts from 10 Western European countries. It consists of short guidelines and technical advice on general precautions, injuries and medical services, permits to work, fire prevention and fighting, jetties, pipework, storage tanks, static electricity, electrical equipment, road vehicles, tank cars, handling of bitumen products, liquefied petroleum gases, packed products and training of personnel. The code is supplemented by 10 appendices, including a suggested syllabus for a 2-day course on fire prevention and emergency action for managers of oil installations.

Royal Dutch Petroleum Company annual report 1992

International Nuclear Information System (INIS)

Anon.

1993-01-01

The Royal Dutch Petroleum Company has no operations of its own and virtually the whole of its income derives from its 60% interest in the companies known collectively as the Royal Dutch/Shell Group of Companies; the other 40% is owned by the Shell Transport and Trading Company, p.l.c. The company is engaged in the oil, natural gas, chemicals, coal and metals businesses throughout the world. The annual report summarises the year's results and analyses earnings in each industry segment. Financial statements for the year ended 31 December 1992 are presented. The Group companies' estimated net quantities of crude oil, natural gas and coal are given

Report for the coal type committee in fiscal 1992; 1992 nendo tanshu iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper reports the activities of the coal type committee in fiscal 1992, and summarizes the main technological achievements. In the Chinese coal liquefaction test, fiscal 1991 has performed liquefaction tests on Fushun coal by using a small continuous testing facility (0.1 t/d) at the Coal Chemistry Research Institute in Beijing. Fiscal 1992 has completed the liquefaction tests on Shengli coal. In October, a liquefaction test was carried out by using Tianzhu coal according to the NEDOL process. This paper reports the result of the liquefaction test on the Shengli coal, and the result of the analysis on the Fushun coal liquefied oil. The coal type selection and investigation having been performed to date reveals close correlation among the maceral composition of coal, coal rank and liquefied oil yield. Coals having good reactivity and suitable for liquefaction are generally suitable also for gasification. In the pretreatment of coal as a gasification material for hydrogen manufacture, a test was performed by using A heavy oil and tar sand bitumen plus A heavy oil as the granulating agents. With Montana coal, the highest de-ashing rate was achieved when the oil was added at 35% by weight. Both of the reaction rate and oil yield were improved. A handling test was carried out up to 72.5 degrees C, wherein Tatung coal presented no problems in both of the discharging and sticking tendencies. (NEDO)

Self-cementitious properties of fly ashes from CFBC boilers co-firing coal and high-sulphur petroleum coke

International Nuclear Information System (INIS)

Sheng Guanghong; Li Qin; Zhai Jianping; Li Feihu

2007-01-01

Self-cementitious properties of fly ash from circulating fluidized bed combustion boiler co-firing coal and high-sulphur petroleum coke (CPFA) were investigated. CPFA was self-cementitious which was affected by its fineness and chemical compositions, especially the contents of SO 3 and free lime (f-CaO). Higher contents of SO 3 and f-CaO were beneficial to self-cementitious strength; the self-cementitious strength increases with a decrease of its 45 μm sieve residue. The expansive ratio of CPFA hardened paste was high because of generation of ettringite (AFt), which was influenced by its water to binder ratio (W/A), curing style and grinding of the ash. The paste cured in water had the highest expansive ratio, and grinding of CPFA was beneficial to its volume stability. The hydration products of CPFA detected by X-ray diffraction (XRD) and scanning electron microscopy (SEM) were portlandite, gypsum, AFt and hydrated calcium silicate (C-S-H)

76 FR 80553 - Mandatory Reporting of Greenhouse Gases: Technical Revisions to the Petroleum and Natural Gas...

Science.gov (United States)

2011-12-23

... permeability gas, shale gas, coal seam, or other tight reservoir rock. For example, wells producing coal bed... separation means one or more of the following processes: forced extraction of natural gas liquids, sulfur and... Mandatory Reporting of Greenhouse Gases: Technical Revisions to the Petroleum and Natural Gas Systems...

Study on possible explosive reactions of sodium nitrate-bitumen mixtures initiated by a shock wave

International Nuclear Information System (INIS)

Savornin, J.; Vasseur, C.

1986-01-01

Potential hazards of the mixture sodium nitrate-bitumen obtained by embedding in bitumen liquid radioactive effluents concentrated by evaporation are studied in case of accidental shock wave. A theoretical evaluation based on thermodynamical data show a low probability, nevertheless different from zero. No explosion occurred in tests realized in severe conditions. In conclusion there is no risk of detonation of large quantity of bitumen-nitrates stored in 200-liter drum in radioactive waste storage [fr

Morphology, Microstructure and Physico-Mechanical Properties of Pasargad Bitumen, Modified by Ethylene-Vinyl Acetate Copolymer (EVA and Nanoclay

Directory of Open Access Journals (Sweden)

Arezoo Ghaempour

2015-09-01

Full Text Available Due to the characteristics such as flexibility, adhesion, hydrophobicity and low price, bitumen is used in different construction and insulation industries. The major problem with the bitumen material is its restricted physico-mechanical properties, mainly high temperature rutting and low temperature cracking. The aim of this work was to modify bitumen, produced in Tabriz Pasargad Oil Company, and evaluation of its different properties to make it suitable for the weather conditions of North West of Iran. The physico-mechanical, morphological and rheological characteristics of EVA/Cloisite 15A modified bitumen were studied.Two different feeding instructions were used in the mixing of bitumen with modifiers.In the first method, EVA and Cloisite 15A nanoclay were simultaneously added into the molten bitumen and in the second method, EVA and Cloisite 15A were premixed in an internal mixer before adding the polymer/nanoclay nanocomposite into the molten bitumen. The results showed that addition of nanoclay and polymer into the bitumen, led increased softening point and a decrease in the penetration of base bitumen, in which the extent of changes, was higher for the samples prepared by masterbatch method. The rheological properties of the pre-mixed samples exhibited more improvement and these samples showed more elastic behavior. The results of optical microscopy showed that the pre-mixing of polymer and nanoclay led to a more uniform distribution of the swollen polymer phase at the base bitumen. These samples also showed higher morphology stability than those samples prepared in single step. These effects were related to the probable localization of nanoclay at the interface of the two phases.

The United Nations Framework Classification for World Petroleum Resources

Science.gov (United States)

Ahlbrandt, T.S.; Blystad, P.; Young, E.D.; Slavov, S.; Heiberg, S.

2003-01-01

The United Nations has developed an international framework classification for solid fuels and minerals (UNFC). This is now being extended to petroleum by building on the joint classification of the Society of Petroleum Engineers (SPE), the World Petroleum Congresses (WPC) and the American Association of Petroleum Geologists (AAPG). The UNFC is a 3-dimansional classification. This: Is necessary in order to migrate accounts of resource quantities that are developed on one or two of the axes to the common basis; Provides for more precise reporting and analysis. This is particularly useful in analyses of contingent resources. The characteristics of the SPE/WPC/AAPG classification has been preserved and enhanced to facilitate improved international and national petroleum resource management, corporate business process management and financial reporting. A UN intergovernmental committee responsible for extending the UNFC to extractive energy resources (coal, petroleum and uranium) will meet in Geneva on October 30th and 31st to review experiences gained and comments received during 2003. A recommended classification will then be delivered for consideration to the United Nations through the Committee on Sustainable Energy of the Economic Commission for Europe (UN ECE).

Waste reduction algorithm used as the case study of simulated bitumen production process

Directory of Open Access Journals (Sweden)

Savić Marina A.

2011-01-01

Full Text Available Waste reduction algorithm - WAR is a tool helping process engineers for environmental impact assessment. WAR algorithm is a methodology for determining the potential environmental impact (PEI of a chemical process. In particular, the bitumen production process was analyzed following three stages: a atmospheric distillation unit, b vacuum distillation unit, and c bitumen production unit. Study was developed for the middle sized oil refinery with capacity of 5000000 tones of crude oil per year. Results highlight the most vulnerable aspects of the environmental pollution that arise during the manufacturing process of bitumen. The overall rates of PEI leaving the system (PEI/h - Iout PEI/h are: a 2.14105, b 7.17104 and c 2.36103, respectively. The overall rates of PEI generated within the system - Igen PEI/h are: a 7.75104, b -4.31104 and c -4.32102, respectively. Atmospheric distillation unit have the highest overall rate of PEI while the bitumen production unit have the lowest overall rate of PEI. Comparison of Iout PEI/h and Igen PEI/h values for the atmospheric distillation unit, shows that the overall rate of PEI generated in the system is 36.21% of the overall rate of PEI leaving the system. In the cases of vacuum distillation and bitumen production units, the overall rate of PEI generated in system have negative values, i.e. the overall rate of PEI leaving the system is reduced at 60.11% (in the vacuum distillation unit and at 18.30% (in the bitumen production unit. Analysis of the obtained results for the overall rate of PEI, expressed by weight of the product, confirms conclusions.

Recent coal and uranium investment agreements in the Third World

International Nuclear Information System (INIS)

Zorn, S.A.

1982-01-01

The improvements made by developing countries in the 1970s in petroleum and mineral agreements with transnational corporations have been well documented, and substantial evidence exists to show that some real gains, in terms of host country control over operations, distribution of economic benefits, better employment and training requirements, etc., have in fact been made. In the case of the energy-related minerals, uranium and coal, however, relatively few contracts between Third World governments and transnational corporations have become public, and it is thus difficult to document whether the same gains made in the case of petroleum or non-fuel minerals have been achieved in relation to these energy resources. This article reviews a number of such recent coal and uranium agreements in developing countries. In overall terms, these agreements do not go as far in providing for the interests of host countries as do those negotiated for petroleum or hard minerals. The reasons for this apparent weakness in developing countries' bargaining power in the case of uranium and coal include the specific nature of the markets for these minerals, the structure of transnational corporations in the industry, and the very secrecy which has kept most of these contracts from public view. (Auth.)

Sulfur isotope in nature. Determination of sulfur isotope ratios in coal and petroleum by mass spectrometry

International Nuclear Information System (INIS)

Derda, M.

1999-01-01

Elementary sulfur or in chemical compounds is one of the elements widespread in the earth's crust and biosphere. Its participation in earth's crust amounts to 0.26 % by weight. Measurement of isotope composition of natural samples can deliver many information about origin, creation and transformation ranges of rocks and minerals. Sulfur isotope ratio contained in minerals is variable and for this reason investigation of isotope sulfur composition can deliver useful information about the geochemistry of each component. Therefore in the investigated sample it is necessary to determine not only the content of sulfur but also the isotope composition of each component. Differentiation of contents of sulfur-34 in natural sulfur compounds can reach up to 110 per mile. So large divergences can be explained by a kinetic effect or by bacterial reduction of sulphates. In this report a wide review of the results of investigations of isotope sulfur compositions in coal and petroleum are presented as well as the methods for the preparation of samples for mass spectrometry analysis are proposed. (author)

Estimation of diffusion coefficients in bitumen solvent mixtures as derived from low field NMR spectra

International Nuclear Information System (INIS)

Wen, Y.; Bryan, J.; Kantzas, A.

2005-01-01

Use of solvents for the extraction of heavy oil and bitumen appears to be an increasingly feasible technology. Both vapour extraction and direct solvent injection are considered for conventional exploration and production schemes, while solvent dilution of bitumen is a standard technique in oil sands mining. Mass transfer between solvent and bitumen is a poorly understood process. In some cases, it is totally ignored compared to viscous force effects. In other cases, phenomenological estimations of diffusion and dispersion coefficients are used. Low field NMR has been used successfully in determining both solvent content and viscosity reduction in heavy oil and bitumen mixtures with various solvents. As a solvent comes into contact with a heavy oil or bitumen sample, the mobility of hydrogen bearing molecules of both solvent and oil changes. These changes are detectable through changes in the NMR relaxation characteristics of both solvent and oil. Relaxation changes can then be correlated to mass flux and concentration changes. Based on Fick's Second Law, a diffusion coefficient, which is independent of concentration, was calculated against three oils and six solvents. (author)

Use of a thin-film evaporator for bitumen coating of radioactive concentrates

International Nuclear Information System (INIS)

Lefillatre, G.; Rodier, J.; Hullo, R.; Cudel, Y.; Rodi, L.

1969-01-01

Following the development in the laboratory of a process for coating evaporation concentrates with bitumen, a technological study of this coating process has been undertaken. The report describes a pilot installation for the bitumen coating of concentrates, which uses a thin-film evaporator LUWA L 150. The first, inactive series of tests was designed to determine the maximum and optimum capacities of the evaporator by varying the amounts of bitumen and of concentrate, the rotor speed and the thermo-fluid temperature. Two rotors were tested, one of conventional type, the other a model especially designed for high viscosity products. The maximum capacity of evaporation of the apparatus is 72 kg/hr for a heating temperature of 221 deg. C. During normal operation, the evaporator can produce 50 kg/hr of coated product containing 55 to 60 per cent of bitumen (Mexphalte 40/50), the water content of the product remaining under 0.5 per cent. A second series of tests will shortly be carried out on this pilot installation using, in particular, bituminous emulsions containing mainly Mexphalte 40/50 and 80/100. (authors) [fr

Process of recovering bitumen from shale

Energy Technology Data Exchange (ETDEWEB)

Ryan, H D

1918-03-26

A step in the recovery of bitumen from solids which consists in digesting the solids with heavy oil under the action of heat and agitation at a temperature insufficiently high to effect substantial distillation of heavy fractions, but high enough to liquefy heavy hydrocarbons contained in the solids, and then separating solid residual matter, substantially as described.

Polyfunctional Modifiers for Bitumen and Bituminous Materials with High Performance

Directory of Open Access Journals (Sweden)

Alim Feizrakhmanovich Kemalov

2018-01-01

Full Text Available Over the last decade increase in capacity and the intensity of vehicular traffic has increased manifoldly, including heavy trucks, super singles, and higher tire pressures, resulting in significant increase of dynamic loads on the road surface which in turn lead to high quality requirements for bitumen in order to avoid premature wear and failure of asphalt concrete pavements. One of the possibilities to increase the quality of bitumen is to use special additives and modifiers that can provide a high adhesion to mineral filler and inhibit the aging and degradation processes in the asphalt coating. To achieve this, in the present study composite modifiers based on bisimidazolines derivatives were synthesized. The developed polyfunctional modifier (PFM of complex action provides enhanced thermal stability, significantly improves the adhesion between bitumen binder and aggregates, and also improves the physical-mechanical properties of the asphalt concrete. Based on the test results it is recommended to use the synthesized samples of the PFM additive with complex action in asphalt mixtures for road paving.

Determination of organic products resulting of chemical and radiochemical decompositions of bitumen. Applications to embedded bitumens; Determination des produits organiques d'alterations chimiques et radiochimiques du bitume. Applications aux enrobes bitumes

Energy Technology Data Exchange (ETDEWEB)

Walczak, I

2000-01-27

Bitumen can be used for embedding most of wastes because of its high impermeability and its relatively low reactivity with of chemicals. Bituminization is one of selected solutions in agreement with nuclear safety, waste compatibility and economic criteria. Bitumen, during storage, undergoes an auto-irradiation due to embedded radio-elements. During this stage,drums are not airtight then oxygen is present. In disposal configuration, water, which is a potential vector of radioactivity and organic matter, is an other hazard factor liable to deteriorate the containment characteristics of bitumen wastes. The generation of water-soluble organic complexing agents can affect the integrity of the wasteform due to an increase of the radionuclides solubility. The first aim of this work is the quantitative and qualitative characterisation of soluble organic matter in bitumen leachates. Different leaching solutions were tested (various pH, ionic strength, ratio S/V). When the pH of the leaching solutions increases, the total organic carbon released increases as well. Identified molecules are aromatics like naphthalene, oxidised compounds like alcohols, linear carbonyls, aromatics, glycols and nitrogen compounds. For the cement equilibrated solution (pH 13.5), the effect of ionic strength becomes significative and influences the release of soluble organic matter. This soluble organic matter can be bio-degraded if microorganisms can growth. The second aim of this work is to study the effect of radio-oxidative ageing on the bitumen confinement properties. During radio-oxidation, the chemical properties of bitumen are modified. The {mu}-IRTF analysis shows the formation of hydroxyl compounds and aromatic acids. The formation of these polar groups does not influence in our study the water uptake. However the organic matter release increases significantly with the irradiation dose. (author)

Hydrocracking of coal extracts to highly aromatic petroleum

Energy Technology Data Exchange (ETDEWEB)

Kotowski, W; Gorski, R

1972-07-01

Coal extracts were hydrocracked at 400 to 450/sup 0/C, 250 atm, 0.8 to 2.0 hr/sup -1/ space velocity, and with 1.5 cu m/l./hr of hydrogen over a bed of fluidized, 0.6 to 0.8 mm granules of nickel-molybdenum zeolite catalyst using the Consolidation Coal Co. process. The 330/sup 0/C bp extract was diluted with the 230 to 320/sup 0/C fraction of the product. At 440/sup 0/C and 1.2 hr/sup -1/ space velocity, the hydrotreatment removed 97% of the sulfur compounds, 95% of oxygen compounds, and 92% of nitrogen compounds. The yield of 35 to 230/sup 0/C gasoline stock decreased with increasing feed space velocity, but that of 230 to 340/sup 0/C gas oils increased. The synthetic crude product contained 48.7% aromatics, 35.1% naphthenes, 13.4% paraffins, 2.8% olefins, 0.14% sulfur, and 1.07% asphaltene. The product is compared with Romashkino crude.

Bituminization process of radioactive liquid wastes by domestic bitumen

International Nuclear Information System (INIS)

Sang, H.L.

1977-11-01

A study has been carried out of the incorporation of intermediate level wastes in bitumen. Two kinds of wastes: a) an evaporator concentrate from a PWR (containing boric acid), b) second cycle wastes from the Purex process (containing sodium salts), were satisfactorily incorporated into a mixture of straight and blown domestic bitumen, to yield a product containing 50wt% solids. The products were stable to radiation exposure of 5'8x10 8 rads. Leach rates were measured in both distilled and sea water over periods up to 200 days at 5 0 C and 25 0 C and at both 1 atm and 8 atm pressure. Results confirmed that long term storage of the products would be satisfactory

Research on swelling clays and bitumen as sealing materials for radioactive waste repositories

International Nuclear Information System (INIS)

Allison, J.A.; Wilson, J.; Mawditt, J.M.; Hurt, J.C.

1991-01-01

This report describes a programme of research to investigate the performance of composite seals incorporating adjacent blocks of swelling clay and bitumen. It is shown that the interaction of the materials can promote a self-sealing mechanism which prevents water penetration, even when defects are present in the bitumen layer. A review of the swelling properties of highly compacted bentonite and magnesium oxide is presented, and the characteristic sealing properties of bituminous materials are described. On the basis of this review, it is concluded that bentonite is the preferred candidate material for use in composite clay/bitumen seals for intermediate-level radioactive waste repositories. However, it is thought that magnesium oxide may have other sealing applications for high-level waste repositories. A programme of laboratory experiments is described in which relevant swelling and intrusion properties of highly compacted bentonite blocks and the annealing characteristics of oxidised and hard-grade industrial bitumens are examined. The results of composite sealing experiments involving different water penetration routes are reported, and factors governing the mechanism of self-sealing are described. The validation of the sealing concept at a laboratory scale indicates that composite bentonite/bitumen seals could form highly effective barriers for the containment of radioactive wastes. Accordingly, recommendations are made concerning the development of the research, including the implementation of full-scale demonstration experiments to simulate conditions in an underground repository. 13 tabs., 41 figs., 62 refs

Constant strain rate experiments and constitutive modeling for a class of bitumen

Science.gov (United States)

Reddy, Kommidi Santosh; Umakanthan, S.; Krishnan, J. Murali

2012-08-01

The mechanical properties of bitumen vary with the nature of the crude source and the processing methods employed. To understand the role of the processing conditions played in the mechanical properties, bitumen samples derived from the same crude source but processed differently (blown and blended) are investigated. The samples are subjected to constant strain rate experiments in a parallel plate rheometer. The torque applied to realize the prescribed angular velocity for the top plate and the normal force applied to maintain the gap between the top and bottom plate are measured. It is found that when the top plate is held stationary, the time taken by the torque to be reduced by a certain percentage of its maximum value is different from the time taken by the normal force to decrease by the same percentage of its maximum value. Further, the time at which the maximum torque occurs is different from the time at which the maximum normal force occurs. Since the existing constitutive relations for bitumen cannot capture the difference in the relaxation times for the torque and normal force, a new rate type constitutive model, incorporating this response, is proposed. Although the blended and blown bitumen samples used in this study correspond to the same grade, the mechanical responses of the two samples are not the same. This is also reflected in the difference in the values of the material parameters in the model proposed. The differences in the mechanical properties between the differently processed bitumen samples increase further with aging. This has implications for the long-term performance of the pavement.

Applicability of CO{sub 2}-based Vapex process to recover Athabasca bitumen

Energy Technology Data Exchange (ETDEWEB)

Badamchi-Zadeh, A.; Maini, B.B.; Yarranton, H.W. [Calgary Univ., AB (Canada). Dept. of Chemical and Petroleum Engineering

2008-10-15

This paper described an experimental apparatus designed to test Vapex process performance in Athabasca bitumen. The study examined the effectiveness of carbon dioxide (CO{sub 2}) as a carrier gas for propane in the Vapex process. The procedure was designed to provide data on the compositional changes in the vapor chamber and solution gas, as well as to more accurately measure the density and viscosity of produced oil. A total of 4 Vapex experiments were conducted in a model packed with glass beads and saturated with Athabasca bitumen. Pure propane, and 2 different mixtures of CO{sub 2} and propane were used as solvents. The study examined stabilized live oil production rates; average fractions of the solvent in the produced oil, the density and viscosity of the produced oil, and the average composition of the solvent in the test vapor chamber. The compositional changes were mapped using an equations of state (EOS) model. The study demonstrated that the Vapex compositional path follows a multi-contact immiscible process that included condensing compositional gravity drainage. Results indicated that while pure propane is a more effective means of recovering Athabasca bitumens, non-condensable gases such as CO{sub 2} must be mixed with propane in order to ensure that the dew point pressure of the solvent remains above reservoir pressures. The study showed that CO{sub 2} can be used to effectively reduce the viscosity of bitumen in conjunction with propane. However, the phase behavior of solvent and bitumen systems in reservoir conditions must be characterized in order to select appropriate injection gas ratios. 17 refs., 3 tabs., 12 figs.

Dustfall design of open coal yard in the power plant-a case study on the closed reconstruction project of coal storage yard in shengli power plant

Science.gov (United States)

Wang, Kunpeng; Ji, Weidong; Zhang, Feifei; Yu, Wei; Zheng, Runqing

2018-02-01

This thesis, based on the closed reconstruction project of the coal storage yard of Shengli Power Plant which is affiliated to Sinopec Shengli Petroleum Administration, first makes an analysis on the significance of current dustfall reconstruction of open coal yard, then summarizes the methods widely adopted in the dustfall of large-scale open coal storage yard of current thermal power plant as well as their advantages and disadvantages, and finally focuses on this project, aiming at providing some reference and assistance to the future closed reconstruction project of open coal storage yard in thermal power plant.

Determination of organic products resulting of chemical and radiochemical decompositions of bitumen. Applications to embedded bitumens; Determination des produits organiques d'alterations chimiques et radiochimiques du bitume. Applications aux enrobes bitumes

Energy Technology Data Exchange (ETDEWEB)

Walczak, I

2000-01-27

Bitumen can be used for embedding most of wastes because of its high impermeability and its relatively low reactivity with of chemicals. Bituminization is one of selected solutions in agreement with nuclear safety, waste compatibility and economic criteria. Bitumen, during storage, undergoes an auto-irradiation due to embedded radio-elements. During this stage,drums are not airtight then oxygen is present. In disposal configuration, water, which is a potential vector of radioactivity and organic matter, is an other hazard factor liable to deteriorate the containment characteristics of bitumen wastes. The generation of water-soluble organic complexing agents can affect the integrity of the wasteform due to an increase of the radionuclides solubility. The first aim of this work is the quantitative and qualitative characterisation of soluble organic matter in bitumen leachates. Different leaching solutions were tested (various pH, ionic strength, ratio S/V). When the pH of the leaching solutions increases, the total organic carbon released increases as well. Identified molecules are aromatics like naphthalene, oxidised compounds like alcohols, linear carbonyls, aromatics, glycols and nitrogen compounds. For the cement equilibrated solution (pH 13.5), the effect of ionic strength becomes significative and influences the release of soluble organic matter. This soluble organic matter can be bio-degraded if microorganisms can growth. The second aim of this work is to study the effect of radio-oxidative ageing on the bitumen confinement properties. During radio-oxidation, the chemical properties of bitumen are modified. The {mu}-IRTF analysis shows the formation of hydroxyl compounds and aromatic acids. The formation of these polar groups does not influence in our study the water uptake. However the organic matter release increases significantly with the irradiation dose. (author)

Thermal-maturity limit for primary thermogenic-gas generation from humic coals as determined by hydrous pyrolysis

Science.gov (United States)

Lewan, Michael; Kotarba, M.J.

2014-01-01

Hydrous-pyrolysis experiments at 360°C (680°F) for 72 h were conducted on 53 humic coals representing ranks from lignite through anthracite to determine the upper maturity limit for hydrocarbon-gas generation from their kerogen and associated bitumen (i.e., primary gas generation). These experimental conditions are below those needed for oil cracking to ensure that generated gas was not derived from the decomposition of expelled oil generated from some of the coals (i.e., secondary gas generation). Experimental results showed that generation of hydrocarbon gas ends before a vitrinite reflectance of 2.0%. This reflectance is equivalent to Rock-Eval maximum-yield temperature and hydrogen indices (HIs) of 555°C (1031°F) and 35 mg/g total organic carbon (TOC), respectively. At these maturity levels, essentially no soluble bitumen is present in the coals before or after hydrous pyrolysis. The equivalent kerogen atomic H/C ratio is 0.50 at the primary gas-generation limit and indicates that no alkyl moieties are remaining to source hydrocarbon gases. The convergence of atomic H/C ratios of type-II and -I kerogen to this same value at a reflectance of indicates that the primary gas-generation limits for humic coal and type-III kerogen also apply to oil-prone kerogen. Although gas generation from source rocks does not exceed vitrinite reflectance values greater than , trapped hydrocarbon gases can remain stable at higher reflectance values. Distinguishing trapped gas from generated gas in hydrous-pyrolysis experiments is readily determined by of the hydrocarbon gases when a -depleted water is used in the experiments. Water serves as a source of hydrogen in hydrous pyrolysis and, as a result, the use of -depleted water is reflected in the generated gases but not pre-existing trapped gases.

Hydrothermal bitumen generated from sedimentary organic matter of rift lakes - Lake Chapala, Citala Rift, western Mexico

Energy Technology Data Exchange (ETDEWEB)

Zarate del Valle, Pedro F. [Departamento de Quimica, Universidad de Guadalajara - CUCEI, Ap. Postal 4-021, Guadalajara, Jalisco CP 44410 (Mexico); Simoneit, Bernd R.T. [Environmental and Petroleum Geochemistry Group, College of Oceanic and Atmospheric Sciences, Oregon State University, Building 104, Corvallis, OR 97331-5503 (United States)]. E-mail: simoneit@coas.oregonstate.edu

2005-12-15

Lake Chapala is in the Citala Rift of western Mexico, which in association with the Tepic-Zacoalco and Colima Rifts, form the well-known neotectonic Jalisco continental triple junction. The rifts are characterized by evidence for both paleo- and active hydrothermal activity. At the south shore of the lake, near the Los Gorgos sublacustrine hydrothermal field, there are two tar emanations that appear as small islands composed of solid, viscous and black bitumen. Aliquots of tar were analyzed by GC-MS and the mixtures are comprised of geologically mature biomarkers and an UCM. PAH and n-alkanes are not detectable. The biomarkers consist mainly of hopanes, gammacerane, tricyclic terpanes, carotane and its cracking products, steranes, and drimanes. The biomarker composition and bulk C isotope composition ({delta} {sup 13}C = -21.4%) indicate an organic matter source from bacteria and algae, typical of lacustrine ecosystems. The overall composition of these tars indicates that they are hydrothermal petroleum formed from lacustrine organic matter in the deeper sediments of Lake Chapala exceeding 40 ka ({sup 14}C) in age and then forced to the lakebed by tectonic activity. The absence of alkanes and the presence of an UCM with mature biomarkers are consistent with rapid hydrothermal oil generation and expulsion at temperatures of 200-250 deg. C. The occurrence of hydrothermal petroleum in continental rift systems is now well known and should be considered in future energy resource exploration in such regions.

Characterization of industrial wastes as raw materials for Emulsified Modified Bitumen (EMB) formulation

Science.gov (United States)

Najib Razali, Mohd; Isa, Syarifah Nur Ezatie Mohd; Salehan, Noor Adilah Md; Musa, Musfafikri; Aziz, Mohd Aizudin Abd; Nour, Abdurahman Hamid; Yunus, Rosli Mohd

2018-04-01

This study was conducted to characterize industrial wastes for formulation of emulsified modified bitumen (EMB) in relation to their physical characteristic and elemental composition. This analysis will give information either raw materials from industrial wastes can be used for EMB formulation. Bitumen is produced from crude oil that is extracted from the ground which categorizes the crude oil as one of the non-renewable form of product. A vast environmental problem issues arises in Malaysia cause by the excessive manufacturing activity that lead to a miss-management of industrial waste has leads to the used of industrial waste in the EMB formulation. Industrial waste such as polystyrene, polyethylene and used automotive oil can be used as alternative to formulate bitumen. Then a suitable emulsifier needs to be added to produce the final product which is EMB. The emulsifier will yield a charge depends on its properties to bind the oily bitumen with water. Physical characteristic studies were performed by thermogravimetric Analysis (TGA), differential scanning calorimetry (DSC), flash point test, density rest and moisture content test. Fourier Transform Infrared Spectroscopy (FTIR) analysis was measured to determine the material’s molecular composition and structure.

Making coke

Energy Technology Data Exchange (ETDEWEB)

Wodehouse-Temple, C G

1929-07-12

Semi-coke is produced by mixing low-value absorbent solid carbonaceous material such as coal dust, slack, gas-works coke, lignite, torbanite, raphilite, cannel, or shale with not more than 20% of a carbonaceous binding material such as petroleum distillation residue, tarry residues, pitch bitumen, Trinidad asphalt, Manjak or the substance known under the registered Trade Mark Gilsonite and subjecting the mixture without briquetting to a temperature not exceeding 550/sup 0/C. According to the first Provisional Specification, the mixture may if desired be briquetted before being heated and the second constituent may be present to the extent of 30%.

Managing hydrogen and molecules in bitumen upgrading : technology and research opportunities

Energy Technology Data Exchange (ETDEWEB)

Gray, M.G. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering

2006-07-01

An innovative concept in oil sands mining, extraction and upgrading was presented with reference to selectively removing metals. The approach presently used to upgrade bitumen is to drive the properties of slurry mixtures closer to conventional crude oils. However, it is necessary to remove unwanted contaminants and to convert nearly all of the vacuum residues. The yield and value of the final product can be improved by maximizing the hydrogen content of the liquid products. The currently used and proposed upgrading methods are based on technologies developed between 1929 and 1954, including coking, hydrotreating, hydroconversion, and gasification. This study compared the main technologies for upgrading in terms of management of raw materials and hydrogen. The feasibility of improving recovery by using new approaches to separate bitumen was considered. It was concluded that the rejection of large fractions of bitumen as coke or asphaltenes is undesirable. New thermal process face design challenges such as distillation versus cracking coking and fouling. There is much potential for breakthrough in asphaltene precipitation technologies, based on paraffinic froth treatment concepts. tabs., figs.

Understanding the relationship : bitumen production and the Athabasca River

Energy Technology Data Exchange (ETDEWEB)

Daughney, S. [Hatch Ltd., Mississauga, ON (Canada)

2009-07-01

This presentation discussed oil sands activities in relation to water use and the Athabasca River. Surface mining uses truck and shovel methods to extract shallow oil sands deposits comprised of bitumen, connate water, coarse sands, and clays. The process involves the use of significant amounts of fresh water. The bitumens are slurried at turbulent conditions in a hydrotransport line which directs the bitumens towards a froth treatment process and diverts coarse sand and fine tailings. The tailings are stored in ponds or used to construct dykes. Water trapped with tailings materials cannot be recycled, and must be replaced from fresh sources. Various consolidate and non-consolidated tailings strategies are being developed to address mature fine tailings (MFT) accumulations. Generic water balance analyses are conducted in order to determine the distribution of site water inputs and losses as well as to determine river water use intensity. A water management framework and tailings performance criteria has been developed for the lower Athabasca River. The framework has been designed to determine cautionary thresholds for the river. River water withdrawals are cumulative for all industries. Intakes may be restricted by 2012. Water from storage must be used to supplement available flow from the river. It was concluded that strategies must also be developed to meet tailings disposal requirements. tabs., figs.

Petroleum-related origin for uraniferous organic-rich nodules of Southwestern Oklahoma

International Nuclear Information System (INIS)

Curiale, J.A.; Bloch, S.; Harrison, W.E.; Rafalska-Bloch, J.

1983-01-01

Geologic field relations and geochemical analyses imply a petroleum-related origin for the organic matter of uraniferous nodules in the Permian Hennessey Group red beds in Kiowa County, Oklahoma. The local presence of crude oil in the shallow subsurface and the absence of local occurrences of plant debris suggest a hydrocarbon-related origin for these nodules. Several oil seeps in the general vicinity of the study area indicate that major steep reverse faults near the nodule site may have provided vertical conduits for petroleum migration from deeper zones. Geochemical analyses of the uraniferous nodules, including infrared spectroscopy and elemental analysis, reveal characteristics of both coal and petroleum. Carbon isotopic analyses favor a petroleum-related origin. A model incorporating field and geochemical evidence is suggested whereby crude oil, migrating from depth, is initially altered near the surface to a more viscous material. Concurrently migrating uranium-bearing ground water is then stripped of its uranium by the degraded petroleum. Therefore, presence of such nodules in the shallow subsurface may suggest buried petroleum deposits. Confirmation of this model must await further study of the effects of radiation damage on organic matter

Effect of Recycled Waste Polymers, Natural Bitumen and HVS Cut on the Properties of Vacuum Bottom

Directory of Open Access Journals (Sweden)

Y. Rasoulzadeh

2013-01-01

Full Text Available The neat bitumen, an oil refining by-product, has its own inherent weakness under long-time loading at low and high temperatures. These performance limitations of neat bitumen have led researchers to modify its physical andmechanical properties. According to several studies, polymers can be used to modify the properties of bitumen. Due to much lower production costs and aiming to reduce environmental impacts, recycled waste polymers are preferred as compared with virgin polymers. In this study, the effect of recycled waste polymers including crumb rubber modifier (CRM, polyethylene and latex and non-polymeric materials such as natural bitumen (NB and heavy vacuum slops (HVS cut on physical and mechanical properties of vacuum bottom residue (VB of crude oil distillation was investigat-ed. Based on the results, recycled waste polyethylene and NB can improve the performance grade of VB at high temperatures and CRM, latex and HVS can improve the performance grade of VB at low temperatures. Thus, by designing various blends of these additives with VB, different modified bitumens can be directly obtained from VB without any need to air-blowing process.

TECHNOLOGY OF REPAIRING OPERATIONAL SUITABILITY BITUMEN-RUBEROID CARPET

Directory of Open Access Journals (Sweden)

MISHUK K. M.

2017-01-01

Full Text Available Raising of problem. In the article is presented the analysis of the existing technologies for the restoration of the operational usability of bitumen-polymeric carpet, which allowed to identify their disadvantages, suggested ways to solve problems and highlighted the results of the studies. Firstly, existing bitumen-ruberoid carpet has a residual hydro insulating capacity that can be effectively used. Secondly, the physical condition of the repaired carpet has different types of defects and damage without the proper removal of which is difficult to ensure the desired outcome. The applying of additional layers in conditions of moistening of the lower layers and other defects contributes to their conservation and accelerated loss of operational integrity.Removal of these impacts can be up to 40-50% of all work, can not provide the required effectiveness outcomes in terms of durability, reliability and cost. Therefore the problem is to find ways to achieve a longer after repairing operation with simultaneous reduction of consumables indicators. Purpose of the study is to develop technological solutions serviceability restoration of roofing using unrolling technologies on the principles to minimize the impact of negative factors and the maximum possible use and strengthen the remaining hydro potential of the insulating coating through the use of special impregnating - saturating compositions. Features such compositions are based on the ability to deeply penetrate the thick bitumen-ruberoid carpet and restore his lost components and provide increased water resistance. Conclusion. The article can be introduced in practice of repair-refurbishable works of soft roofing covering of buildings and constructions.

Foreign investment opportunities in the Venezuelan upstream industry

International Nuclear Information System (INIS)

Pradas, F.

1994-01-01

An overview is provided of the Venezuelan petroleum industry, and the advantages of Venezuela for petroleum industry investment are noted. Proven reserves of hydrocarbons consist of 64 billion bbl of oil and condensates, 3.7 trillion m 3 of natural gas, and some 270 billion bbl of recoverable oil from vast reserves of heavy oil and bitumen. Additional reserves of light and medium crude awaiting discovery are estimated at 40 billion bbl. The state petroleum company PDVSA plans to increase proven reserves and to raise oil production capacity from the present level of 2.8 million bbl/d to 4 million bbl/d. To achieve those increases, it is estimated that PDVSA will need to invest ca $40 billion by the year 2000, of which $28 billion will come from PDVSA's own resources. It is intended that the remainder of the investment will be from foreign enterprises as part of joint ventures. PDVSA already has experience with joint ventures in the refining and petrochemical sectors, and a PDVSA subsidiary, Lagoven, is conducting a natural gas export project with several foreign firms. Another subsidiary, Maraven, is engaging in the first of several ventures to exploit the extensive heavy oil resources of the Orinoco belt. Foreign firms are also acting as contractors to reactivate inactive oil fields. PDVSA also markets Orimulsion, a bitumen-based emulsion fuel which competes with coal as a boiler fuel, through its joint venture subsidiary BITOR

Coprocessing of biooils from biomass pyrolysis and bitumen from oil sands

Energy Technology Data Exchange (ETDEWEB)

Feng, M.; Daruwalla, S.; Daruwalla, D.D. [Southwest Research Inst., San Antonia, TX (United States). Dept. of Chemical Engineering

2009-07-01

Liquid biooils can be produced from the thermochemical treatment of biomass by pyrolysis. However, because of their poor volatility, high viscosity, coking, corrosiveness, and cold flow problems, biooils cannot be used directly as transportation fuel. Biooils can be upgraded into a liquid transportation fuel by hydrodeoxygenation with typical hydrotreating procedure with sulfided cobalt and molybdenum (CoMo) or nickel molybdenum (NiMo) as catalysts in the current oil refinery facilities. Coprocessing of biooils and bitumen from oil sand provides an opportunity to process the two feeds at the same time which can be achieved by injection of pyrolytic biooils and vacuum gas oil (VGO) from bitumen into a fluid catalytic cracking (FCC) unit if the acid number of the biooils is below 35. Typically the biooils are diluted to about 1.5 to 5 per cent in the VGO feed to be processed. For the blends of VGO and biooils, the biooils appear to facilitate the cracking of the VGO and shift yields toward light ends, lower light cycle oil. They also clarify slurry oil, which makes the process more cost effective. This paper briefly reviewed the typical methods for bitumen pretreatment and preliminary upgrading. The paper also discussed the current status of coprocessing of biooils and hydrocarbons, and suggested two possible processes for coprocessing bitumen with biooils and biopitches. The impact on the hydrodesulphurization process conversion of dibenzothiophenic compounds was also studied, showing no differences of the inhibiting effect between these molecules. 8 refs., 4 tabs., 6 figs.

Mechanical lifter for recovering highly viscous oil and bitumens

Energy Technology Data Exchange (ETDEWEB)

Rakhmanov, R N; Akhunov, A M; Asfandiyarov, Kh A; Maksutov, R A

1982-01-01

A mechanical lifter is described for recovering highly viscous oil and bitumens. The lifter differs from the known and has significant advantages over them. The lifter was made and tested on a stand well.

Epoxy modified bitumen : Chemical hardening and its interpretation

NARCIS (Netherlands)

Apostolidis, P.; Pipintakos, G.; van de Ven, M.F.C.; Liu, X.; Erkens, Sandra; Scarpas, Athanasios

2018-01-01

Epoxy modified bitumen (EMB) is a promising technology for long lasting paving materials ensuring higher resistance to rutting, oxygen- and moisture-induced damage. In this paper, an analysis of the chemical reactions that take place during the chemical hardening process (curing) of epoxy modified

Application of coal petrographic methods in petroleum and natural gas exploration. Anwendung kohlenpetrographischer Methoden bei der Erdoel- und Erdgasprospektion

Energy Technology Data Exchange (ETDEWEB)

Teichmueller, M.

1971-02-15

The relationship that exists between coalification and the formation of liquid petroleum and natural gas depends entirely upon the temperature in the earth's crust and the duration of heating. The degree of coalification can be determined by reflectivity measurements on very small vitrinitic (huminitic) inclusions in sedimentary rocks, because a satisfactory correlation has been established between mean reflectivity (R/sub m Oil/) and different parameters of chemical rank using 900 vitrites of different rank. This paper reports the considerable experience obtained with this method using cores and cuttings from boreholes of the German oil industry. Subsequently, examples from other countries are described which confirm the applicability of the method. Results obtained so far suggest that oil deposits may occur when the reflectivity (R/sub m Oil/) of the vitrinite lies between 0.3 and 1.0% (brown coal to high-volatile bituminous stage), whereas economic gas deposits may be found when R/sub m Oil/ extends from 0.7 to 2.0% (high-low volatile bituminous stage).

Tire-tread and bitumen particle concentrations in aerosol and soil samples

DEFF Research Database (Denmark)

Fauser, Patrik; Tjell, Jens Christian; Mosbæk, Hans

2002-01-01

% of the mass of airborne particulate tire debris have aerodynamic diameters smaller than 1 mum. The mean aerodynamic diameter is about I gm for the bitumen particles. This size range enables the possibility for far range transport and inhalation by humans. Soil concentrations in the vicinity of a highway...... indicate an approximate exponential decrease with increasing distance from the road. Constant values are reached after about 5 m for the tire particles and 10 m for the bitumen particles. Concentrations in soil that has not been touched for at least 30 years show a decrease in tire concentration...

Characterization of the viscoelastic behavior of the pure bitumen grades 10/20 and 35/50 with macroindentation and finite element computation

KAUST Repository

Hamzaoui, Rabah; Guessasma, Sofiane; Bennabi, Abdelkrim

2013-01-01

In this article, we present an identification procedure that allows the determination of the viscoelasticity behavior of different grades of pure bitumen (bitumen 35/50 and bitumen 10/20). The procedure required in the first stage a mechanical

Quantification of bitumen particles in aerosol and soil samples using HP-GPC

DEFF Research Database (Denmark)

Fauser, Patrik; Tjell, Jens Christian; Mosbæk, Hans

2000-01-01

A method for identifying and quantifying bitumen particles, generated from the wear of roadway asphalts, in aerosol and soil samples has been developed. Bitumen is found to be the only contributor to airborne particles containing organic molecules with molecular weights larger than 2000 g pr. mol....... These are separated and identified using High Performance Gel Permeation Chromatography (HP-GPC) with fluorescence detection. As an additional detection method Infra Red spectrometry (IR) is employed for selected samples. The methods have been used on aerosol, soil and other samples....

Petroleum Oxidation in Marine Microcosms by Natural Microbial Assemblages

Science.gov (United States)

Wardlaw, G. D.; Reddy, C. M.; Nelson, R. K.; Ehrhardt, C. J.; Valentine, D. L.

2006-12-01

Millions of gallons of petroleum are emitted into marine environments each year and the oxidation of this oil by microbes is an important mechanism for mediating toxicity. In terms of quantity, petroleum is the most abundant organic pollutant impacting marine environments today. Recent advances in chromatography have led to the development of comprehensive two-dimensional gas chromatography (GC &GC). The acronym, GC GC, is used because orthogonal gas chromatographic separations are achieved in both analytical dimensions by using stationary phases with varying partitioning abilities and selectivity. This novel method has greatly expanded the analytical window of petroleum hydrocarbons and was used to track the loss of petroleum hydrocarbons in aerobic marine microcosm experiments. Sediment microcosms were composed of seawater and sediment collected from the Coal Oil Point (COP) seep field off the coast of Santa Barbara, CA. Oil collected directly from the reservoir underlying the seep field was added to each microcosm, and samples were incubated for one year. Net metabolism was tracked by quantifying oxygen consumption and carbon dioxide production. The loss of petroleum components was tracked with GC GC, whereas the bacterial and archaeal community structures were tracked using T-RFLP. Results of these incubation studies will be presented.

Rationale for continuing R&D in indirect coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

Gray, D.; Tomlinson, G. [MITRE Corp., McLean, VA (United States)

1995-12-31

The objective of this analysis is to use the world energy demand/supply model developed at MITRE to examine future liquid fuels supply scenarios both for the world and for the United States. This analysis has determined the probable extent of future oil resource shortages and the likely time frame in which the shortages will occur. The role that coal liquefaction could play in helping to alleviate this liquid fuels shortfall is also examined. The importance of continuing R&D to improve process performance and reduce the costs of coal-derived transportation fuel is quantified in terms of reducing the time when coal liquids will become competitive with petroleum.

Underground gasification of coal - possibilities and trends

International Nuclear Information System (INIS)

Dushanov, D.; Minkova, V.

1994-01-01

A detailed historical review is given on the problem of underground coal gasification (UCG) with emphasis on its physical, chemical, technological and financial aspects. The experience of USA, Japan, former USSR, Belgium, UK and France is described. The feasibility of UCG in the Dobrudzhan Coal Bed in Bulgaria is discussed. The deposit has reserves of about 1.5 billion tones at relatively shallow depths. Almost the whole scale from long flame to dry coal is covered. According to its coalification degree the bed belongs to gas coal - V daf 35-40%; C daf 80-83%, eruption index = 1. Enriched samples has low sulfur content - 0.6-1.5% and low mineral content - 6-12%. Having in mind the lack of domestic natural gas and petroleum resources, the authors state that the utilisation of the bed will alleviate the energy problems in Bulgaria. 24 refs., 5 figs., 1 tab

Influence of mineral fillers on the rheological response of polymer-modified bitumens and mastics

Directory of Open Access Journals (Sweden)

F. Cardone

2015-12-01

Full Text Available The rheological properties of the bituminous components (bitumen and bituminous mastic within asphalt mixtures contribute significantly to the major distresses of flexible pavements (i.e. rutting, fatigue and low temperature cracking. Asphalt mixtures are usually composed of mastic-coated aggregates rather than pure bitumen-coated aggregates. The purpose of this study is to investigate the effects of mineral fillers on the rheological behaviour of several polymer-modified bitumens (PMBs through laboratory mixing. A neat bitumen and two types of polymers (elastomeric and plastomeric were used to produce PMBs, and two fillers with different minerals (limestone and basalt were selected to obtain mastics. The dynamic shear rheometer (DSR and bending beam rheometer (BBR were used to characterize the rheological properties of PMBs and mastics. In particular, multiple stress creep recovery (MSCR tests were performed to evaluate the rutting potential at high temperatures, whereas BBR tests were carried out to investigate the low temperature behaviour of these materials. BBR results for unmodified mastics show that the increase of stiffness is similar regardless of the filler type, whereas results for polymer-modified mastics indicate that the degree of stiffening depends on the combination of filler/polymer types. MSCR results show that adding filler leads to a reduced susceptibility of permanent deformation and an enhanced elastic response, depending on the combination of filler/polymer types. Overall results suggest that a physical–chemical interaction between the filler and bitumen occurs, and that the interaction level is highly dependent on the type of polymer modification.

Indirect coal liquefaction - the first commercial CTL project in the USA

Energy Technology Data Exchange (ETDEWEB)

Radtke, K.; Battensby, D.; Marsico, C.; Hooper, M.; Mather, C. [Uhde GmbH (Germany)

2006-07-01

The polygeneration of fuels, chemical and power offers an innovative and economically advantageous way to utilise disadvantaged fuels, such as lignite, waste coal and petroleum coke, in a coal-to-liquids (CTL) plant by means of integration of three main process blocks: gasification island to convert coal into clean synthesis gas; Fischer-Tropsch synthesis to convert synthesis gas into clean liquid fuels and chemicals; and combustion of synthesis gas to produce electric power and steam. This paper describes the process and technology side of this indirect coal liquefaction project with key plant data that has been elaborated for a commercial scale CTL project, which is expected to be the first CTL plant in the USA. The plant will use the Shell Coal Gasification process. 6 figs.

Development of paraffin and paraffin/bitumen composites with additions of B2O3 for thermal neutron shielding applications

International Nuclear Information System (INIS)

Toyen, Donruedee; Saenboonruang, Kiadtisak

2017-01-01

In this work, paraffin and paraffin/bitumen composites with additions of boron oxide (B 2 O 3 ) were prepared to evaluate the viscosity, flexural, and thermal neutron shielding properties for uses as thermal neutron shielding materials. The results showed that the addition of 3 wt% or 9 wt% bitumen to paraffin increased the overall flexural properties with the content of 9 wt% bitumen having the highest values. The improvement in flexural properties made the composites less brittle, stiffer, and longer-lasting. Furthermore, different contents of B 2 O 3 (0, 7, 14, 21, 28, and 35 wt%) were added to paraffin and paraffin/bitumen composites to investigate the effects of the B 2 O 3 contents. The results indicated that an increase in B 2 O 3 contents improved the shielding properties but slightly reduced the flexural properties. Specifically for 5-mm paraffin and 5-mm paraffin/bitumen samples with 35 wt% of B 2 O 3 , both samples could reduce neutron flux by more than 70%. The overall results suggested that the paraffin and paraffin/bitumen composites with additions of B 2 O 3 showed improved properties for utilization as effective thermal neutron shielding materials. (author)

Coal, an unavoidable energy in the 21. century

International Nuclear Information System (INIS)

Botte, J.M.

2010-01-01

With the steam engine generalization, coal has become the emblematic energy source of the 19. century industrial revolution and of the progress of the maritime and rail transports. It should have been disappeared of the world energy during the first half of the 21. century on account of the production of nobler energies (nuclear power, petroleum, natural gas, photovoltaic energy or wind power) and of the requirements of the climatic change. Nevertheless, all around the world, coal backs down and sets up as an unavoidable fuel for the 2030-2050 scenarios. (O.M.)

Main scientific and technical development tasks for the coal industry during the 8th Five Year Plan and up to the year 2000

Energy Technology Data Exchange (ETDEWEB)

Klimek, M.

1987-05-01

A general overview is given of the Czechoslovak coal industry from 1975 to 1985, when output increased from 114.4 Mt to 126.6 Mt, with statistics given in graphs and tables covering types of mining, types of coal and types of equipment used. The scientific and technical development plan is reviewed up to the year 2000 which will include intensive geological surveys, more automation, increasing productivity and more efficient use of coking coal. The paper describes in more detail State Scientific Program P01, Extraction and Processing of Selected Types of Fuel, which is broken down into 6 sections: forecasting reserves and geotechnical problems, design problems, surface mining, underground mining, extraction of bitumen and coal processing. This is the first time in the history of the Czechoslovak mining industry that its problems have been incorporated into a State Scientific Program. 6 refs.

Crustaceans from bitumen clast in Carboniferous glacial diamictite extend fossil record of copepods.

Science.gov (United States)

Selden, Paul A; Huys, Rony; Stephenson, Michael H; Heward, Alan P; Taylor, Paul N

2010-08-10

Copepod crustaceans are extremely abundant but, because of their small size and fragility, they fossilize poorly. Their fossil record consists of one Cretaceous (c. 115 Ma) parasite and a few Miocene (c. 14 Ma) fossils. In this paper, we describe abundant crustacean fragments, including copepods, from a single bitumen clast in a glacial diamictite of late Carboniferous age (c. 303 Ma) from eastern Oman. Geochemistry identifies the source of the bitumen as an oilfield some 100-300 km to the southwest, which is consistent with an ice flow direction from glacial striae. The bitumen likely originated as an oil seep into a subglacial lake. This find extends the fossil record of copepods by some 188 Ma, and of free-living forms by 289 Ma. The copepods include evidence of the extant family Canthocamptidae, believed to have colonized fresh water in Pangaea during Carboniferous times.

The conditioning of radioactive waste by bitumen

International Nuclear Information System (INIS)

Rodier, J.; Scheidhauer, J.; Malabre, M.

1961-01-01

The separation of radioactive sludge and waste by bitumen is studied. Results are given concerning various trials carried out on the lixiviation of the final product by water as a function of the pH, of the time, and of the composition. The conditions for carrying out this process of coating the waste are controlled from a radioactive point of view. (author) [fr

Low-shear rheology and sedimentation stability of coal-oil dispersions

Energy Technology Data Exchange (ETDEWEB)

Rutter, P. R.; Davies, J. M.; Jones, T. E.R.

1984-10-15

Stable coal-oil mixtures can be prepared by grinding coal particles in fuel oil. These products have been prepared by the British Petroleum Company plc and are referred to as Coal-Oil Dispersions (COD). One of the major problems associated with the production of DOD is the rapid assessment of the length of time the coal particles are likely to remain in suspension under a particular set of storage conditions. This paper describes a number of measurements of the low-shear rheology and sedimentation stability of a series of CODs prepared by grinding two types of coal in two different fuel oils. The results suggest that two types of COD are possible. One type exhibits complex rheological properties at low shear rates and does not produce a coal sediment, even after prolonged storage at 80/sup 0/C under dynamic conditions. The other exhibits near Newtonian behaviour and appears to form a sedimented layer of coal during storage.

Present situation of the development of petroleum substitution energy (Germany); Sekiyu daitai energy kaihatsu no genjo (Doitsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper investigates and reports the developmental trend of petroleum substitution energy in Germany. Policies for the technical development and actual introduction of petroleum substitution energy in Germany are concerned with three energies: coal, natural gas, and new energy, except nuclear energy the use of which is against public opinion. Coal is the only abundant domestic resource, but not internationally competitive because of its cost. Brown coal obtained from the open pit mining is an abundant and low-cost domestic resource, but has the environmental problem. The latest technology is actually being introduced in which the thermal power generation is integrated into gasification, and the gas/steam turbine power generation. Natural gas is advancing in the use as energy source for space heating substituting for brown coal. The technology development of new energy is promoted mainly on such wind power and solar energy as are called renewable energy. As to the development of technology using renewable energy for which the rapid increasing use is not expected in near future, the target is directed mostly to CO2 control and the third world where there are no public electric power nets. 30 refs., 10 figs., 8 tabs.

RADIATION CHEMICAL CONVERSION OF OIL DERIVED FROM OIL-BITUMEN ROCK

Directory of Open Access Journals (Sweden)

Lala Jabbarova

2014-06-01

Full Text Available The results of research in the radiation processing of synthetic oil derived from oil–bitumen rock of the Balakhany deposit in Azerbaijan are presented. The study has been conducted on a 60Co gamma-source at a dose rate of P = 0.5 Gy/s and various absorbed doses of D = 43–216 kGy. Samples of synthetic oil from natural bitumen rocks have been analyzed by chromatography, gas chromatography–mass spectrometry, and IR-spectroscopy, and their radiation resistance has been evaluated. The results of the study allow for both assessment of the feasibility of manufacturing petrochemicals for various applications by radiation processing and use of these materials for isolating radioactive sources to preclude their impact on the environment.

Investigation on performances of asphalt mixtures made with Reclaimed Asphalt Pavement: Effects of interaction between virgin and RAP bitumen

Directory of Open Access Journals (Sweden)

Luca Noferini

2017-07-01

Full Text Available According to most recent surveys, the European area produced 265 mil tonnes of asphalt for road applications in 2014. In the same year, the amount of available RAP was more than 50 mil tonnes. The use of RAP in new blended mixes reduces the need of neat bitumen, making RAP recycling economically attractive. Despite the economic and environmental benefits, road authorities tend to limit the use of RAP in asphalt mixes due to uncertainty about field performances. The present study focuses on the interaction between neat and RAP bitumen in asphalt mixes made with different RAP content. The effects of RAP on physical and rheological properties of the final bituminous blend were investigated. This study is part of a wider research, where a specific type of asphalt mixture was produced with different RAP contents being 10%, 20% and 30% by mass of the mix. Bitumen was extracted and recovered from asphalt mixes, then it was subjected to the following laboratory tests: standard characterization, dynamic viscosity and rheological analysis with DSR. Findings showed that the effects of RAP bitumen on the final blend varied in proportion to RAP content. A threshold value of RAP content was found, below which bitumen was not subjected to significant changes in physical and rheological properties. Practical implications on production methods and paving of RAP mixes are also proposed. Keywords: Reclaimed Asphalt Pavement (RAP, Recycling, Bitumen blending, Bitumen rheology

PETROBRAS green petroleum coke used as partial replacement for coal injected mixtures in blast furnaces; Utilizacao do coque verde de petroleo da PETROBRAS em substituicao parcial ao carvao mineral das misturas injetadas em altos fornos

Energy Technology Data Exchange (ETDEWEB)

Silva, Agenor Medrado da; Medrado, Swami Botelho; Noblat, Sebastiao Jorge Xavier [Companhia Siderurgia Nacional. CSN. Gerencia Geral de Processos Siderurgicos. RJ (Brazil)], e-mails: ams@csn.com.br, swami@csn.com.br, s.noblat@csn.com.br; Carvalho Junior, Joao Andrade de [Universidade Estadual Paulista Julio de Mesquita Filho. Faculdade de Engenharia de Guaratingueta. Departamento de Energia, SP (Brazil)], e-mail: joao@feg.unesp.br

2010-04-15

The PETROBRAS produced green petroleum coke (GPC) is a carbon rich fuel, virtually ash-free, with low sulfur content and is a fuel suitable to replace metallurgical coke in blast furnaces. The GPC was tested in a pulverized coal injection simulator built in the Volta Redonda research center. It presented a low burning efficiency due to low volatile material content and high substitution rate by the carbon content. The industrial-scale tests were carried out in blast furnaces with up to 50% PETROBRAS GPC in the coal blends, which has never been done before in the steel industry. The injected coal/CVP mixtures produced no negative side effects in the blast furnace grinding systems, pneumatic conveying or operating process. The mixture burning process inside the blast furnace, showed a decrease in fuel consumption, with a significant reduction in metallurgical coke consumption. The industrial-scale tests of the GPC mixtures did not reach the 70% maximum for lack of the GPC feedstock, it being necessary to continue with standard coal mixtures. (author)

Laboratory Tests of Bitumen Samples Elasticity

Science.gov (United States)

Ziganshin, E. R.; Usmanov, S. A.; Khasanov, D. I.; Khamidullina, G. S.

2018-05-01

This paper is devoted to the study of the elastic and acoustic properties of bitumen core samples. The travel velocities of the ultrasonic P- and S-waves were determined under in-situ simulation conditions. The resulting data were then used to calculate dynamic Young's modulus and Poisson's ratio. The authors studied the correlation between the elasticity and the permeability and porosity. In addition, the tests looked into how the acoustic properties had changed with temperature rise.

Panorama 2010: World coal resources

International Nuclear Information System (INIS)

Bessereau, G.; Saniere, A.

2010-01-01

At a time when the international community must face the key challenges posed by global warming as well as sustainability in general and many of our fellow citizens have come to look unfavorably upon fossil energies, the world is still heavily dependent on these energies to cover growing global energy demand. With proved reserves equivalent to more than 120 years at the present rate of extraction, with a better worldwide geographical distribution than petroleum, coal seems like an especially secure energy. While the renewable energies are showing rapid growth but still only represent a small proportion of the world energy mix, coal was the energy whose consumption grew at the fastest rate and for the sixth consecutive year. This gives cause for concern when one realizes that coal is also the most environmentally harmful energy at local level (its extraction generates pollution) and globally (its combustion emits CO 2 ). So how is it possible to reconcile the apparently irreconcilable, especially when, in some countries, coal represents the bulk of the energy resources? Since it is impossible to do without coal, the solution is to develop new 'clean coal' technologies, among which the capture and storage of CO 2 looks like a promising pathway. In the process, it will be necessary to overcome major technical, economic and social challenges. (author)

Synthesis of hydrocarbons using coal and nuclear process heat

International Nuclear Information System (INIS)

Eickhoff, H.G.; Kugeler, K.

1975-01-01

An analysis of the global petroleum resources and demand shows that the amount of mineral oil products is sufficient to meet the requirements of the next decades. The geographical resources, however, could lead to problems of distribution and foreign exchange. The production of hydrocarbons with coal as basis using high temperature nuclear process heat has advantages compared to the conventional techniques. Next to the conservation of reserve fossil primary energy carriers there are advantages as regards prices, which at high coal costs are especially pronounced. (orig.) [de

Bitumen based modified substance

International Nuclear Information System (INIS)

Kostolanyi, P.

1987-01-01

The necessary amounts of tetrahydrosilicic acid and methyl phenyl silicon oil are added to molten bitumen heated to temperatures of 50 to 200 degC. The mixture is thoroughly mixed and let to cool. The structure of the product comes close to gel and its properties (penetration, softening point, workability time, penetration index) may be changed in dependence on the amount of additions and on the time and temperature of heating. The advantage of the thus prepared modified material is its shorter workability time, its ability to bind materials with a certain water content, and its relatively low price. It may be used for fixing and storing low-and medium-level radioactive organic and thickened waste waters. (E.S.)

Introduction to selected references on fossil fuels of the central and southern Appalachian basin: Chapter H.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Ruppert, Leslie F.; Lentz, Erika E.; Tewalt, Susan J.; Román Colón, Yomayra A.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

The Appalachian basin contains abundant coal and petroleum resources that have been studied and extracted for at least 150 years. In this volume, U.S. Geological Survey (USGS) scientists describe the geologic framework and geochemical character of the fossil-fuel resources of the central and southern Appalachian basin. Separate subchapters (some previously published) contain geologic cross sections; seismic profiles; burial history models; assessments of Carboniferous coalbed methane and Devonian shale gas; distribution information for oil, gas, and coal fields; data on the geochemistry of natural gas and oil; and the fossil-fuel production history of the basin. Although each chapter and subchapter includes references cited, many historical or other important references on Appalachian basin and global fossil-fuel science were omitted because they were not directly applicable to the chapters.

Impact of the Ageing on Viscoelastic Properties of Bitumen with the Liquid Surface Active Agent at Operating Temperatures

Science.gov (United States)

Iwański, Marek; Cholewińska, Malgorzata; Mazurek, Grzegorz

2017-10-01

The paper presents the influence of the ageing on viscoelastic properties of the bitumen at road pavement operating temperatures. The ageing process of bituminous binders causes changes in physical and mechanical properties of the bitumen. This phenomenon takes place in all stages of bituminous mixtures manufacturing, namely: mixing, storage, transport, placing. Nevertheless, during the service life it occurs the increase in stiffness of asphalt binder that is caused by the physical hardening of bitumen as well as the influence of oxidation. Therefore, it is important to identify the binder properties at a high and low operating temperatures of asphalt pavement after simulation of an ageing process. In the experiment as a reference bitumen, the polymer modified bitumen PMB 45/80-65 was used. The liquid surface active agent FA (fatty amine) was used as a bitumen viscosity-reducing modifier. It was added in the amount of 0,2%, 0,4% and 0,6% by the bitumen mass. All binder properties have been determined before ageing (NEAT) and after long-term ageing simulated by the Pressure Ageing Vessel method (PAV). To determine the binder properties at high temperatures the dynamic viscosity at 60°C was tested. On the basis of test results coming from the dynamic viscosity test it was calculated the binder hardening index. The properties at a low temperature were determined by measuring the creep modulus using Bending Beam Rheometer (BBR) at four temperatures: -10°C, -16°C, -22°C and -28°C. The stiffness creep modulus “S” and parameter “m” were determined. On the basis of dynamic viscosity test it was found that the ageing process caused a slight decrease in a dynamic viscosity. The level of a hardening index considerably increased at 0.6% fatty amine content. The long-term ageing process had a minor effect on stiffening of a polymer modified bitumen with FA additive regardless of a low temperature and an amount of fatty amine content.

Assessment of dermal exposure to bitumen condensate among road paving and mastic crews with an observational method

NARCIS (Netherlands)

Agostini, M.; Fransman, W.; Vocht, F.D.; Joode, B.V.W.D.; Kromhout, H.

2011-01-01

Objective: To assess dermal exposure to bitumen condensate among road pavers and indoor mastic workers in multiple crews using a semi-quantitative observational method [DeRmal Exposure Assessment Method (DREAM)].Methods: Two skilled observers assessed dermal exposure to bitumen condensate among 85

Why investors shy away from coal

International Nuclear Information System (INIS)

Roling, D.A.

1994-01-01

Why do investors shy away from coal? This may sound like a strange question given the change in ownership of many major coal companies in recent years, but the ongoing consolidation within the coal industry is quite different from any actual new investment in the industry. To begin to understand why, one must return to the early '70s, a time of low-cost, abundant energy. The price of oil was about $2-4/bbl until 1973. The price of natural gas was about 60 cents/M ft 3 , and coal was approximately $7/st. This, however, was before the first Organization of the Petroleum Exporting Countries (OPEC) shock. The price of coal declined throughout the 1980s, and continues its downward path in some markets. Many coal investments have not achieved their expected return, such as the case of a 1M st/yr mine in West Virginia, which was developed in the early '80s only to be put immediately on a care-and-maintenance basis, where it languished until it was sold in 1990. Other mines, such as the large open-pit mines in the Powder River Basin in Wyoming, never reached their targeted production rates. Some of these large mines had equipment that remained in crates for years, only later to be sold at a loss. The extent of losses on investments in coal mines is discussed

Geology and oil and gas assessment of the Fruitland Total Petroleum System, San Juan Basin, New Mexico and Colorado: Chapter 6 in Geology and Oil and Gas Assessment of the Fruitland Total Petroleum System, San Juan Basin, New Mexico and Colorado

Science.gov (United States)

Ridgley, J.L.; Condon, S.M.; Hatch, J.R.

2013-01-01

The Fruitland Total Petroleum System (TPS) of the San Juan Basin Province includes all genetically related hydrocarbons generated from coal beds and organic-rich shales in the Cretaceous Fruitland Formation. Coal beds are considered to be the primary source of the hydrocarbons. Potential reservoir rocks in the Fruitland TPS consist of the Upper Cretaceous Pictured Cliffs Sandstone, Fruitland Formation (both sandstone and coal beds), and the Farmington Sandstone Member of the Kirtland Formation, and the Tertiary Ojo Alamo Sandstone, and Animas, Nacimiento, and San Jose Formations.

Report on evaluation for SRC-2 coal liquefaction project; SRC-II sekitan ekika project hyoka sagyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-10-01

Among the EDS, H-Coal and SRC-2 lined up in the coal liquefaction project of the U.S., the SRC is aimed at producing 6,000 t/day as a module for a 30,000 t/day commercial plant. They expect Ash contents (iron, sulfur, etc.) in coal without basically using catalysts. The products are applicable to fuels for electricity and gas for the moment. In the element technology, there are some problems in manufacturing hydrogen by gasification of residuals as well as in slurry systems, reaction towers, etc.. In the 30,000 ton commercial plant, the coal-liquefied oil costs $19.89/bbl (price as of 1978) assuming coal costs $29.47; therefore, the feasibility is strong as a substitute for petroleum. Japan's share for the required funds will be 86.8 billion yen (if 250 yen per dollar). Since the kinds of coal are conceivably increased in number through the improvement of the process, the Pacific rim countries and these which lie on the Indian Ocean are assumed to be the major coal producing countries for Japan. The stability in storage of coal-liquefied oil is experimentally excellent, as is the compatibility with petroleum products for example. Great results can be expected in the technical know-how and the spread of element technology for Japan. (NEDO)

Report on evaluation for SRC-2 coal liquefaction project; SRC-II sekitan ekika project hyoka sagyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-10-01

Among the EDS, H-Coal and SRC-2 lined up in the coal liquefaction project of the U.S., the SRC is aimed at producing 6,000 t/day as a module for a 30,000 t/day commercial plant. They expect Ash contents (iron, sulfur, etc.) in coal without basically using catalysts. The products are applicable to fuels for electricity and gas for the moment. In the element technology, there are some problems in manufacturing hydrogen by gasification of residuals as well as in slurry systems, reaction towers, etc.. In the 30,000 ton commercial plant, the coal-liquefied oil costs $19.89/bbl (price as of 1978) assuming coal costs $29.47; therefore, the feasibility is strong as a substitute for petroleum. Japan's share for the required funds will be 86.8 billion yen (if 250 yen per dollar). Since the kinds of coal are conceivably increased in number through the improvement of the process, the Pacific rim countries and these which lie on the Indian Ocean are assumed to be the major coal producing countries for Japan. The stability in storage of coal-liquefied oil is experimentally excellent, as is the compatibility with petroleum products for example. Great results can be expected in the technical know-how and the spread of element technology for Japan. (NEDO)

The heat is on. Petroleum, power and politics; Der Klima-GAU. Erdoel, Macht und Politik

Energy Technology Data Exchange (ETDEWEB)

Gelbspan, R.

1998-07-01

In the tradition of American investigative journalism, Gelbspan does not stop at describing the impending climate disaster but throws a critial light on the falsifications of the coal and petroleum industry aimed at preventing public discussion of the subject. Coal and petroleum companies spend millions of dollars to convince the public that there is no such thing as global heating. In his clear style and with references to reliable sources, Ross Gelbspan demands that we should oppose the dissuasion strategy of the petroleum industry and presents measures and counter-strategies to break the power of the industry and prevent the ecological disaster. [German] In der bedeutenden Tradition des amerikanischen investigativen Journalismus fuehrt uns Gelbspan nicht nur die drohende Klimakatastrophe selbst vor Augen. Er durchleuchtet darueber hinaus kritisch und mit politischem Impetus die Taeuschungsmanoever der Kohle- und Erdoelindustrie, mit denen die oeffentliche Diskussion ueber das Thema verhindert werden soll. Die Kohle- und Erdoelriesen geben Millionen dafuer aus, der Oeffentlichkeit einzureden, dass es keine Erwaermung gibt. Anschaulich und mit zuverlaessigen Belegen ruft Ross Gelbspan zum Widerstand gegen die Verschleierungsstrategie der Oelindustrie auf und beschreibt Massnahmen und Gegenstrategien, die die Macht der Industrie brechen und das oekologische Desaster abwenden koennen. (orig.)

Mechanical Properties of Millet Husk Ash Bitumen Stabilized Soil ...

African Journals Online (AJOL)

Akorede

lateritic soil blocks using Millet Husk Ash (MHA) and Bitumen as additives so as to reduce its high cost and find ... eliminating the need for air-conditioning and are warm during the cold ... The mix properties were used in producing soil bricks of ...

Complexation of Cu2+, Ni2+ and UO22+ by radiolytic degradation products of bitumen

International Nuclear Information System (INIS)

Loon, L.R. Van; Kopajtic, Z.

1990-05-01

The radiolytic degradation of bitumen was studied under conditions which reflect those which will exist in the near field of a cementitious radioactive waste repository. The potential complexation capacity of the degradation products was studied and complexation experiments with Cu 2+ , Ni 2+ and UO 2 2+ were performed. In general 1:1 complexes with Cu 2+ , Ni 2+ and UO 2 2+ , with log K values of between 5.7 and 6.0 for Cu 2+ , 4.2 for Ni 2+ and 6.1 for UO 2 2+ , were produced at an ionic strength of 0.1 M. The composition of the bitumen water was analysed by GC-MS and IC. The major proportion of the bitumen degradation products in solution were monocarboxylic acids (acetic acid, formic acid, myric acid, stearic acid ...), dicarboxylic acids (oxalic acid, phthalic acid) and carbonates. The experimentally derived log K data are in good agreement with the literature and suggest that oxalate determines the speciation of Cu 2+ , Ni 2+ and UO 2 2+ in the bitumen water below pH=7. However, under the high pH conditions typical of the near field of a cementitious repository, competition with OH-ligands will be large and oxalate, therefore, will not play a significant role in the speciation of radionuclides. The main conclusion of the study is that the radiolytic degradation products of bitumen will have no influence on radionuclide speciation in a cementitious near field and, as such, need not to be considered in the appropriate safety assessment models. (author) 12 figs., 11 tabs., 31 refs

Investigating the rheological properties of crumb rubber modified bitumen and its correlation with temperature susceptibility

Directory of Open Access Journals (Sweden)

Nuha Salim Mashaan

2013-02-01

Full Text Available There is substantial evidence on the advantages of using crumb rubber in enhancing conventional bitumen properties, gaining environmental protection and boosting industrial-economical benefits. Thus, the use of this ingenious additive in bitumen modification through sustainable technology is highly advocated.The main objective of this research is to investigate the effects of different blending conditions (of time and temperature and various crumb rubber contents on the properties of bitumen binders. Testing was conducted using the Dynamic shear rheometer (DSR test and softening point test. The results showed that differing crumb rubber contents and blending temperature have significant effects on modified binder properties whereas the blending time showed an insignificant effect. Higher blending temperature and crumb rubber content were found to influence the interaction of bitumen-rubber blends and also increased the swelling rate of rubber particles, resulting in an increase in complex shear modulus (G*, storage modulus (G', loss modulus (G" and softening point as well as a decrease in phase angle (δ. Thus, the modified bitumen became less susceptible to deformation after stress removals. The study also presented a considerable relationship between rheological parameters (G*, G', G' and δ and softening point in terms of predicting physical-mechanical properties regardless of blending conditions. Thus, in terms of elasticity for the softening point data, the storage modulus and phase angle were found to be good indicators of binder elasticity. When softening point is made available, a prediction about binder ability to recover its original shape after stress removals can be done.

Investigating the rheological properties of crumb rubber modified bitumen and its correlation with temperature susceptibility

Directory of Open Access Journals (Sweden)

Nuha Salim Mashaan

2012-01-01

Full Text Available There is substantial evidence on the advantages of using crumb rubber in enhancing conventional bitumen properties, gaining environmental protection and boosting industrial-economical benefits. Thus, the use of this ingenious additive in bitumen modification through sustainable technology is highly advocated.The main objective of this research is to investigate the effects of different blending conditions (of time and temperature and various crumb rubber contents on the properties of bitumen binders. Testing was conducted using the Dynamic shear rheometer (DSR test and softening point test. The results showed that differing crumb rubber contents and blending temperature have significant effects on modified binder properties whereas the blending time showed an insignificant effect. Higher blending temperature and crumb rubber content were found to influence the interaction of bitumen-rubber blends and also increased the swelling rate of rubber particles, resulting in an increase in complex shear modulus (G*, storage modulus (G', loss modulus (G" and softening point as well as a decrease in phase angle (δ. Thus, the modified bitumen became less susceptible to deformation after stress removals. The study also presented a considerable relationship between rheological parameters (G*, G', G' and δ and softening point in terms of predicting physical-mechanical properties regardless of blending conditions. Thus, in terms of elasticity for the softening point data, the storage modulus and phase angle were found to be good indicators of binder elasticity. When softening point is made available, a prediction about binder ability to recover its original shape after stress removals can be done.

Incorporation of bitumen and calcium silicate in cement and lime stabilized soil blocks

Science.gov (United States)

Kwan, W. H.; Cheah, C. B.; Ramli, M.; Al-Sakkaf, Y. K.

2017-04-01

Providing affordable housing is the most critical problem in many of the developing countries. Using earth materials in building construction is one of the feasible methods to address this issue and it can be a way towards sustainable construction as well. However, the published information on the stabilized soil blocks is limited. Therefore, the present study is conducted to examine the characterization of the soils and engineering properties of the stabilized soil blocks. Four types of stabilizer were used in the study, namely; cement, slaked lime, bitumen emulsion and calcium silicate. Cement and slaked lime were added at different percentages in the range of 5% to 15%, with interval of 2.5%. The percentage was determined based on weight of soil. Meanwhile, bitumen emulsion and calcium silicate were incorporated at various percentages together with 10% of cement. Dosage of bitumen emulsion is in the range of 2% to 10% at interval of 2% while calcium silicate was incorporated at 0.50%, 0.75%, 1.00%, 1.25%, 1.50% and 2.00%. Results show that cement is the most viable stabilizer for the soil block among all stabilizers in this study. The bulk density, optimum moisture content and compressive strengths were increased with the increasing cement content. The most suitable cement content was 10% added at moisture content of 12%. Lime, bitumen and calcium contents were recommended at 5.0%, 6.0% and 1.25%, respectively.

Rheological Behaviour of a Bitumen Modified with Metal Oxides Obtained by Regeneration Processes

Directory of Open Access Journals (Sweden)

Tullio Giuffrè

2018-02-01

Full Text Available Nowadays, one important challenge is to demonstrate an innovative and integrated approach for the sustainable construction of roads considering the whole life cycle of the infrastructure. Road pavements with multiple asphalt layers generally undergo prolonged environmental exposure and the alternation between solar irradiation and low temperatures. As a result, relaxation or progressive removal of the material with a negative impact on the resistance to plastic deformation occur, also leading to the formation of slits and to dimensional variations, which are commonly defined as thermal cracking. This suggests the use of suitable bitumen modifiers. For these, important parameters are the optimal mixing time and mixing temperature, in order to reduce problems related to the stability of the bitumen. Therefore, the behaviour, upon changing the temperature, of bituminous mixtures containing (as fillers a series of metal oxides coming, as secondary products, from spent acid solutions regeneration processes, was investigated. This is intended in order to recover and reuse those otherwise dangerous wastes coming from several industrial (especially, metallurgical processes. The study was aimed at evaluating the properties of bituminous blends by performing rheological tests under dynamic shear regime. More specifically, five different bitumen matrices were prepared (70/100 bitumen and blends with metal oxides and/or SBS copolymer. Results showed that the addition of iron oxides leads to an increase of the softening point and the complex modulus. The increase is even more emphasized when SBS is added to the blend.

Cogeneration Technology Alternatives Study (CTAS). Volume 6: Computer data. Part 1: Coal-fired nocogeneration process boiler, section B

Science.gov (United States)

Knightly, W. F.

1980-01-01

About fifty industrial processes from the largest energy consuming sectors were used as a basis for matching a similar number of energy conversion systems that are considered as candidate which can be made available by the 1985 to 2000 time period. The sectors considered included food, textiles, lumber, paper, chemicals, petroleum, glass, and primary metals. The energy conversion systems included steam and gas turbines, diesels, thermionics, stirling, closed cycle and steam injected gas turbines, and fuel cells. Fuels considered were coal, both coal and petroleum based residual and distillate liquid fuels, and low Btu gas obtained through the on site gasification of coal. Computer generated reports of the fuel consumption and savings, capital costs, economics and emissions of the cogeneration energy conversion systems (ECS's) heat and power matched to the individual industrial processes are presented. National fuel and emissions savings are also reported for each ECS assuming it alone is implemented. Two nocogeneration base cases are included: coal fired and residual fired process boilers.

Development and utilization of bitumen immobilizing process for radioactive waste materials; Razvoj i primena procesa imobilizacije radioaktivnog otpadnog materijala bitumenskim postupkom

Energy Technology Data Exchange (ETDEWEB)

Peric, A; Plecas, I; Kostadinovic, A [Institut za Nuklearne Nauke Boris Kidric, Belgrade (Yugoslavia)

1988-07-01

Bitumenization is one of the relevant methods for solidification of radioactive waste materials in nuclear technology, today. Bitumenization of R.A. wastes can be obtained either with batch or continual process. In 'IBK', mixer-evaporator vessel for batch process, with continual feeder of process influents, was developed. From the several R.A. materials, that can be solidified into bitumen, ion-exchanged resins, used in NPP Krsko, were chosen and treated, at the various ranges of pH and T. Researches and experiments pointed and verified on use of Yugoslav produced bitumens, as a matrix media for immobilizing the solid R.A. (author)

Process of extraction in liquid way, of the bitumen from asphaltic and bituminous rocks, shale, etc

Energy Technology Data Exchange (ETDEWEB)

Freda, L

1936-06-04

A process is described for liquid extraction of the bitumen in asphaltic and bituminous rocks, shales, and the like. The substances impregnated with bitumen are suitably treated for the extraction of pitch with any given solvent derived from ethylene, in a series of apparatuses fixed and rotary at atmospheric pressure or in vacuum with vapor and hot air.

The adsorption of Cs+, Sr2+ and Ni2+ on bitumen: a mechanistic model

International Nuclear Information System (INIS)

Loon, L.R. Van; Kopajtic, Z.

1991-01-01

The adsorption of radionuclides on the waste matrix is a positive effect and contributes to the retardation of released radionuclides migrating to the geo-and biosphere. For the safety assessment studies, it is important to know whether or not radionuclides do adsorb on the waste matrix. In the present work the adsorption of 134 Cs + , 85 Sr 2+ and 63 Ni 2+ on bitumen was studied as a function of the pH and ionic strength of the equilibrium solution. Bitumen emulsions with well defined surfaces were used. The surface of bitumen is negatively charged due to the deprotonation of weak acid carboxyl groups at the interface. The functional group density amounts to 1.37.10 18 groups/m 2 and their deprotonation behaviour can be well described by the 'Ionizable Surface Group' model. Cs + , Sr 2+ and Ni 2+ adsorb on the surface by three different processes, i.e. ion exchange, outer sphere complexation and inner sphere surface complexation respectively. The adsorption depends on the pH and the ionic strength of the contact solution. Under near field conditions, Cs + and Sr 2+ do not adsorb on the bitumen due to the competition with Na + , K + and Ca 2+ present in the cement pore water in contact with the bitumen. Ni 2+ adsorption can also be neglected because the formation of neutral and anionic hydroxo complexes in solution competes strongly with the adsorption reaction. Other hydrolysable radionuclides of interest are expected to behave similarly to Ni 2+ . The main conclusion of the study is that the adsorption of radionuclides under near field conditions is expected to be very low. Consequently, this process need not to be considered in safety assessment studies. (author) figs., tabs., 30 refs

Effect of nitrogen and phosphate limitation on utilization of bitumen ...

African Journals Online (AJOL)

PRECIOUS

2009-12-15

Dec 15, 2009 ... utilization of bitumen and production of bitu-oil and gas by a bacterial ... nitrogen and phosphorus, with a consequent limitation on degradation of the ..... concluded that in industrial setting, carbon starvation in anaerobic ...

Bitumen to refined products and petrochemicals : a preliminary assessment

International Nuclear Information System (INIS)

Crandall, G.

2004-01-01

Purvin and Gertz is an energy consulting firm that provides advise to the energy sector. A review of western Canadian crude oil supply suggests that oil sands production will surpass declining conventional production. Oil sands supply includes synthetic crude oil (SCO), bitumen and diluent. It is expected that oil sands will increase from 42 per cent of western supply in 2002 to 78 per cent in 2015. This presentation reviewed the potential of Alberta's oil sands and presented a recent study of refined products and petrochemicals from bitumen. Upgrading, refining and petrochemical case studies were presented. In particular, the author examined if a Canadian oil sands upgrading project with high capital costs can be competitive with competing projects in the United States and internationally. In addition to supply and demand issues, the presentation examined infrastructure capability and market potential in the United States. The economic potential and risks of preferred business cases compared to upgrading to SCO were also evaluated. tabs., figs

Modular High Temperature Gas-Cooled Reactor heat source for coal conversion

International Nuclear Information System (INIS)

Schleicher, R.W. Jr.; Lewis, A.C.

1992-09-01

In the industrial nations, transportable fuels in the form of natural gas and petroleum derivatives constitute a primary energy source nearly equivalent to that consumed for generating electric power. Nations with large coal deposits have the option of coal conversion to meet their transportable fuel demands. But these processes themselves consume huge amounts of energy and produce undesirable combustion by-products. Therefore, this represents a major opportunity to apply nuclear energy for both the environmental and energy conservation reasons. Because the most desirable coal conversion processes take place at 800 degree C or higher, only the High Temperature Gas-Cooled Reactors (HTGRs) have the potential to be adapted to coal conversion processes. This report provides a discussion of this utilization of HTGR reactors

Brent coal typing by combined optical and geochemical studies

Energy Technology Data Exchange (ETDEWEB)

Ducazeaux, J.; Le Tran, K.; Nicolas, G. (Societe Nationale des Petroles d' Aquitaine (SNPA), 64 - Pau (France))

1991-12-01

Palynological,petrographical and organic geochemical studies show that various kinds of coal occur throughout the Middle Jurassic Brent Group in the Viking Graben. Two types of coal with strong contrast in terms of source rock potential are thoroughly investigated in this study. It is found that they are relevant to two distinct organic facies. Though having the same organic carbon content, they are very different with respect to the petroleum generating potential, one being a conventional gas-prone coal of type III kerogen and the other one of type II-(III) kerogen which should be considered as an oil-generating coal. Explanations are sought for the difference observed, both geochemically and optically. Palynological study shows the occurrence of two distinct communities of land plants in relation with the depositional environment and climatic changes, whilst coal petrographical study shows that the macerals are unevenly and differently distributed in these two coal types. The original organic material and the depositional environment appear to be the main controlling factors. 13 Refs.; 8 Figs.

U.S. DOE indirect coal liquefaction program: An overview

Energy Technology Data Exchange (ETDEWEB)

Shen, J.; Schmetz, E.; Winslow, J.; Tischer, R. [Dept. of Energy, Germantown, MD (United States); Srivastava, R.

1997-12-31

Coal is the most abundant domestic energy resource in the United States. The Fossil Energy Organization within the US Department of Energy (DOE) has been supporting a coal liquefaction program to develop improved technologies to convert coal to clean and cost-effective liquid fuels to complement the dwindling supply of domestic petroleum crude. The goal of this program is to produce coal liquids that are competitive with crude at $20 to $25 per barrel. Indirect and direct liquefaction routes are the two technologies being pursued under the DOE coal liquefaction program. This paper will give an overview of the DOE indirect liquefaction program. More detailed discussions will be given to the F-T diesel and DME fuels which have shown great promises as clean burning alternative diesel fuels. The authors also will briefly discuss the economics of indirect liquefaction and the hurdles and opportunities for the early commercial deployment of these technologies. Discussions will be preceded by two brief reviews on the liquid versus gas phase reactors and the natural gas versus coal based indirect liquefaction.

Characterization of cement and bitumen waste forms containing simulated low-level waste incinerator ash

International Nuclear Information System (INIS)

Westsik, J.H. Jr.

1984-08-01

Incinerator ash from the combustion of general trash and ion exchange resins was immobilized in cement and bitumen. Tests were conducted on the resulting waste forms to provide a data base for the acceptability of actual low-level waste forms. The testing was done in accordance with the US Nuclear Regulatory Commission Technical Position on Waste Form. Bitumen had a measured compressive strength of 130 psi and a leachability index of 13 as measured with the ANS 16.1 leach test procedure. Cement demonstrated a compressive strength of 1400 psi and a leachability index of 7. Both waste forms easily exceed the minimum compressive strength of 50 psi and leachability index of 6 specified in the Technical Position. Irradiation to 10 8 Rad and exposure to 31 thermal cycles ranging from +60 0 ) to -30 0 C did not significantly impact these properties. Neither waste form supported bacterial or fungal growth as measured with ASTM G21 and G22 procedures. However, there is some indication of biodegradation due to co-metabolic processes. Concentration of organic complexants in leachates of the ash, cement and bitumen were too low to significantly affect the release of radionuclides from the waste forms. Neither bitumen nor cement containing incinerator ash caused any corrosion or degradation of potential container materials including steel, polyethylene and fiberglass. However, moist ash did cause corrosion of the steel

Effect of bitumen emulsion on setting, strength, soundness and ...

Indian Academy of Sciences (India)

Unknown

Effect of bitumen emulsion on setting, strength, soundness and moisture resistance of oxychloride cement. M P S CHANDRAWAT†, T N OJHA and R N YADAV*. Department of Chemistry, R N Ruia Government College, Ramgarh-Shekhawati (Sikar) 331 024, India. †Department of Chemistry, R R Government College, ...

BP and NCB to collaborate in coal liquefaction study. [Supercritical gas extraction; dissolution in anthracene oil

Energy Technology Data Exchange (ETDEWEB)

1978-02-17

British Petroleum and NCB are collaborating in a two year study of coal liquefaction which could result in a demonstration plant being built. The two liquefaction techniques which the NCB is developing at present are supercritical extraction, and dissolution in anthracene oil. A disadvantage of the latter process is that high grade coking coals must be used.

Rationale for continuing R&D in direct coal conversion to produce high quality transportation fuels

Energy Technology Data Exchange (ETDEWEB)

Srivastava, R.D.; McIlvried, H.G. [Burns and Roe Services Corp., Pittsburgh, PA (United States); Gray, D. [Mitre Corp, McLean, VA (United States)] [and others

1995-12-31

For the foreseeable future, liquid hydrocarbon fuels will play a significant role in the transportation sector of both the United States and the world. Factors favoring these fuels include convenience, high energy density, and the vast existing infrastructure for their production and use. At present the U.S. consumes about 26% of the world supply of petroleum, but this situation is expected to change because of declining domestic production and increasing competition for imports from countries with developing economies. A scenario and time frame are developed in which declining world resources will generate a shortfall in petroleum supply that can be allieviated in part by utilizing the abundant domestic coal resource base. One option is direct coal conversion to liquid transportation fuels. Continued R&D in coal conversion technology will results in improved technical readiness that can significantly reduce costs so that synfuels can compete economically in a time frame to address the shortfall.

Diluent and bitumen, an uneasy mix : considerations for treating, blending, transportation, marketing and refining

Energy Technology Data Exchange (ETDEWEB)

Todd, C. [Connacher Oil and Gas Ltd., Calgary, AB (Canada)

2009-07-01

This presentation evaluated several issues regarding the use of diluent as a blending agent with Canadian bitumen. Heavy and viscous crude oils are commonly diluted with condensates and gasolines. This improves field processing, transportability in pipelines and acceptability in markets and refineries. The demand for such diluent is increasing because of the large amounts of heavy oil and bitumen currently produced in Canada. The current tenable price of diluents has meant that a wide range of diluent sources and components are finding their way into the Canadian diluent supply stream. This has raised concerns regarding diluent performance and the affect on blended crude oils. The cost of diluent is among the most controllable expense associated with most bitumen production projects. Market factors were considered in this presentation, such as supply demand; price and infrastructure; operational processing and blending issues; diluent quality and component variability; and downstream issues such as refinery processing and production. tabs., figs.

EM-SAGD/EM-GD : electromagnetic heating method : sustainable improvement of in-situ bitumen recovery

Energy Technology Data Exchange (ETDEWEB)

Wacker, B.; Diehl, D.; Huber, N.; Torlak, M.; Koolman, M. [Siemens AG, Munich (Germany)

2010-07-01

This paper described an electro-magnetic heating technology for the in situ recovery of bitumen. Studies have indicated that the technology promises a higher yield of bitumen with a smaller surface footprint than other bitumen production technologies. A laboratory study conducted with an inductor loop embedded in a 1 meter{sup 3} sand-box demonstrated that the technology is technically feasible. A series of field tests were then conducted by Siemens in a conductive subsurface later in Deggendorf, Germany. The field test included remotely operated surface equipment that was tested under down-scaled field conditions over a period of 6 months. New fiber optic sensors were used to obtain underground temperature readings. The field tests demonstrated a rise in temperature caused by the induction of eddy currents through electromagnetic fields in the conductive sub-surface. Results of the study will be used at an oil sands reservoir in 2011. The process can be combined with steam assisted gravity drainage (SAGD) processes. 4 refs., 7 figs.

Effect of nitrogen and phosphate limitation on utilization of bitumen ...

African Journals Online (AJOL)

PRECIOUS

2009-12-15

Dec 15, 2009 ... Carbon (iv) oxide. Bromine + gas. Decolourization. Alkene and alkyne suspect. Cold acidified potassium tetraoxomanganate(vii) + gas. Decolourzation. Alkene and alkyne suspect. Silver trioxonitrate (v) + gas. No reaction. Alkene confirmed. Figure 7. The IR analysis of bitumen before biodegradation.

Microscopical characterization of carbon materials derived from coal and petroleum and their interaction phenomena in making steel electrodes, anodes and cathode blocks for the Microscopy of Carbon Materials Working Group of the ICCP

Science.gov (United States)

Predeanu, G.; Panaitescu, C.; Bălănescu, M.; Bieg, G.; Borrego, A.G.; Diez, M. A.; Hackley, Paul C.; Kwiecińska, B.; Marques, M.; Mastalerz, Maria; Misz-Kennan, M.; Pusz, S.; Suarez-Ruiz, I.; Rodrigues, S.; Singh, A. K.; Varma, A. K.; Zdravkov, A.; Zivotić, D.

2015-01-01

This paper describes the evaluation of petrographic textures representing the structural organization of the organic matter derived from coal and petroleum and their interaction phenomena in the making of steel electrodes, anodes and cathode blocks.This work represents the results of the Microscopy of Carbon Materials Working Group in Commission III of the International Committee for Coal and Organic Petrology between the years 2009 and 2013. The round robin exercises were run on photomicrograph samples. For textural characterization of carbon materials the existing ASTM classification system for metallurgical coke was applied.These round robin exercises involved 15 active participants from 12 laboratories who were asked to assess the coal and petroleum based carbons and to identify the morphological differences, as optical texture (isotropic/anisotropic), optical type (punctiform, mosaic, fibre, ribbon, domain), and size. Four sets of digital black and white microphotographs comprising 151 photos containing 372 fields of different types of organic matter were examined. Based on the unique ability of carbon to form a wide range of textures, the results showed an increased number of carbon occurrences which have crucial role in the chosen industrial applications.The statistical method used to evaluate the results was based on the “raw agreement indices”. It gave a new and original view on the analysts' opinion by not only counting the correct answers, but also all of the knowledge and experience of the participants. Comparative analyses of the average values of the level of overall agreement performed by each analyst in the exercises during 2009–2013 showed a great homogeneity in the results, the mean value being 90.36%, with a minimum value of 83% and a maximum value of 95%.

Multi-scale sustainability assessments for biomass-based and coal-based fuels in China.

Science.gov (United States)

Man, Yi; Xiao, Honghua; Cai, Wei; Yang, Siyu

2017-12-01

Transportation liquid fuels production is heavily depend on oil. In recent years, developing biomass based and coal based fuels are regarded as promising alternatives for non-petroleum based fuels in China. With the rapid growth of constructing and planning b biomass based and coal based fuels production projects, sustainability assessments are needed to simultaneously consider the resource, the economic, and the environmental factors. This paper performs multi-scale analyses on the biomass based and coal based fuels in China. The production cost, life cycle cost, and ecological life cycle cost (ELCC) of these synfuels are investigated to compare their pros to cons and reveal the sustainability. The results show that BTL fuels has high production cost. It lacks of economic attractiveness. However, insignificant resource cost and environmental cost lead to a substantially lower ELCC, which may indicate better ecological sustainability. CTL fuels, on the contrary, is lower in production cost and reliable for economic benefit. But its coal consumption and pollutant emissions are both serious, leading to overwhelming resource cost and environmental cost. A shifting from petroleum to CTL fuels could double the ELCC, posing great threat to the sustainability of the entire fuels industry. Copyright © 2017 Elsevier B.V. All rights reserved.

Bitumen pyrolysis

International Nuclear Information System (INIS)

Braehler, G.; Noll, T.

2014-01-01

In the past bitumen was a preferred matrix for the embedding of low and intermediate level radioactive waste: its geological history promised long term stability in final repositories. A great variety of waste has been embedded: technological waste, spent ion exchange resins, concrete, rubble, etc. Liquid waste like evaporator concentrates can be dried and embedded simultaneously in extruders, allowing simple processes and equipment. Unfortunately, during long term intermediate storage the bituminized waste drums proved out being not as stable as expected: a significant number turned out to be no longer acceptable for final disposal, and some of them even needed repacking to enable further intermediate storage. A method to rework such drums with bituminized radioactive waste seems to be urgently needed. Pyrolysis and pyro-hydrolysis (= pyrolysis with water steam added) have a long history for the treatment of organic waste: spent solvent (TBP), spent ion exchange resins, alpha waste (predominantly PVC), etc. Due to its low process temperature and the endothermic character, such processes offer significant safety advantages, as compared to incineration or dissolving in organic solvents. Results of lab-scale investigations and concepts for facilities are presented. (authors)

Research on swelling clays and bitumen as sealing materials for radioactive waste repositories

International Nuclear Information System (INIS)

Allison, J.A.; Wilson, J.; Mawditt, J.M.; Hurt, J.C.

1990-10-01

This report describes a programme of research to investigate the performance of composite seals comprising juxtaposed blocks of highly compacted bentonite clay and bitumen. It is shown that interaction of the materials can promote a self-sealing mechanism which prevents weather penetration, even when defects are present in the bitumen layer. Factors affecting seal performance are examined by means of laboratory experiments, and implications for the design of repository backfilling and sealing systems are discussed. It is concluded that design principles and material specifications should be further developed on the basis of large scale experiments. (author)

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline E. Burgess Clifford; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2007-03-17

This report summarizes the accomplishments toward project goals during the no cost extension period of the third year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts for a third round of testing, the use of a research gasoline engine to test coal-based gasoline, and modification of diesel engines for use in evaluating diesel produced in the project. At the pilot scale, the hydrotreating process was modified to separate the heavy components from the LCO and RCO fractions before hydrotreating in order to improve the performance of the catalysts in further processing. Hydrotreating and hydrogenation of the product has been completed, and due to removal of material before processing, yield of the jet fuel fraction has decreased relative to an increase in the gasoline fraction. Characterization of the gasoline fuel indicates a dominance of single ring alkylcycloalkanes that have a low octane rating; however, blends containing these compounds do not have a negative effect upon gasoline when blended in refinery gasoline streams. Characterization of the diesel fuel indicates a dominance of 3-ring aromatics that have a low cetane value; however, these compounds do not have a negative effect upon diesel when blended in refinery diesel streams. Both gasoline and diesel continue to be tested for combustion performance. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Activated carbons have proven useful to remove the heavy sulfur components, and unsupported Ni/Mo and Ni/Co catalysts have been very effective for

Coal reserves in the United States and around the world

International Nuclear Information System (INIS)

Jubert, K.; Masudi, H.

1995-01-01

There is an urgent need to examine the role that coal might play in meeting world energy needs during the next 20 years. Oil from the Organization of Petroleum Exporting Countries (OPEC) can no longer be relied upon to provide expanding supplies of energy, even with rapidly rising prices. Neither can nuclear energy be planned on for rapid expansion worldwide until present uncertainties about it are resolved. Yet, the world's energy needs will continue to grow, even with vigorous energy conservation programs and with optimistic rates of expansion in the use of solar energy. Coal already supplies 25% of the world's energy, its reserves are vast, and it is relatively inexpensive. This study, with the aid of reports from the World Coal Study (WOCOL) examines the needs for coal on a global scale, its availability past and present, and its future prospects

Report on the general course training of the fiscal 1996 coal engineer training program; 1996 nendo sekitan gijutsusha yosei jigyo ippan course kenshu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

The paper reported the general training of the fiscal 1996 coal engineer training program supported by NEDO. In Japan, where natural resource is poor, it is important to transfer from its petroleum dependence energy structure to the system for new energy development and dispersed energy supply. Coal resource is distributed widely in the world and is expected to spread in the future as a main substitute for petroleum. Worldwide attention is much paid to coal supply/demand and environmental problems, but the situation surrounding coal is not necessarily favorable. Under these conditions, Japan is a prominent coal importing country and is on the world-top level in terms of coal utilization technology. Japan has heavy responsibility and needs to play a leading role in adjusting and solving various problems on coal both domestically and internationally. Under the circumstances, 7 persons who are engaged in the coal related business and expected to be in future (3 from the mining relation and 4 from electric power comapanies) participated in the training this fiscal year and received the top-level training in Japan and overseas. 20 figs., 3 tabs.

Checking the mathematical model of the radionuclides migration velocity in the system: bitumen-spent ion-exchange resins; Provera matematickog modela za brzinu izluzivanja radionukluda u sistemu: bitumen-istrosene jonoizmenjivacke smole

Energy Technology Data Exchange (ETDEWEB)

Peric, A; Plecas, I; Kostadinovic, A [Institute of Nuclear Sciences VINCA, Belgrade (Yugoslavia)

1992-07-01

Immobilization process of the spent ion-exchange resins was performed in bitumen matrix. from the twelve investigated formulations, one was chosen: BIT 200-40% I.I. resin, on which the mathematical model of the migration velocity for radionuclides Co-60 and Cs-137 was checked. Behaviour of the migration velocity trend obtained by mathematical modeling was compared with the measured results. Leaching level trends obtained by measurements and by mathematical modeling of the process do not show great differences in the nearly two years of investigation, and pointed out the stability of the bitumenized rad-waste form in the relatively relevant period of time. (author)

Low severity conversion of activated coal

Energy Technology Data Exchange (ETDEWEB)

Hirschon, A.S.; Ross, D.S.

1990-01-01

The results suggest that coal contains regions with structural components significantly reactive under the hydrothermal environment. Although the specific mechanism for this process remains to be developed, this activity is reminiscent of findings in studies of accelerated maturation of oil shale, where hydrothermal treatment (hydrous pyrolysis) leads to the production of petroleum hydrocarbons. In line with what has been seen in the oil shale work, the pretreatment-generated hydrocarbons and phenols appear to represent a further or more complete maturation of some fraction of the organic material within the coal. These observations could have an impact in two areas. The first is in the area of coal structure, where immature, reactive regions have not been included in the structures considered at present. The second area of interest is the more practical one of conversions to coal liquids and pyrolytic tars. It seems clear that the hydrothermal pretreatment changes the coal in some manner that favorably affects the product quality substantially and, as in the CO/water liquefaction case, favorably affects the yields. The conversions of coals of lower rank, i.e., less mature coals, could particularly benefit in terms of both product quality and product quantity. The second portion of this project also shows important benefits to coal conversion technology. It deals with synthesizing catalysts designed to cleave the weak links in the coal structure and then linking these catalysts with the pretreatment methods in Task 2. The results show that highly dispersed catalysts can effectively be used to increase the yields of soluble material. An important aspect of highly dispersed catalysts are that they can effectively catalyze coal conversion even in poor liquefaction solvents, thus making them very attractive in processes such as coprocessing where inexpensive liquefaction media such as resids are used.

Petroleum systems modelling of the Muensterland Basin and Ruhr Basin with special emphasis on unconventional gas resources

Energy Technology Data Exchange (ETDEWEB)

Uffmann, A.K.; Littke, R. [RWTH Aachen Univ. (Germany). Inst. of Geology and Geochemistry of Petroleum and Coal

2013-08-01

A 3D petroleum system model was built for the area of the northern Rhenish Massif and Muensterland/Ruhr Basin in order to reconstruct burial and temperature histories as well as petroleum generation and storage. The basin contains numerous potential unconventional gas reservoirs, i.e. more than 100 Pennsylvanian (Westphalian and upper Namurian) coal seams and several black shales of Pennsylvanian and Mississippian age. The focus here is on the Upper Alum Sahle ('Hangende Alaunschiefer') representing the uppermost Mississippian.

CFD simulation of coal gasification in an entrained-flow gasifier

DEFF Research Database (Denmark)

Sreedharan, V.; Hjertager, B.H.; Solberg, T.

2010-01-01

in reliability, emission control, efficiency, and feedstock flexibility. The feedstock used for a gasification system can be coal, petroleum coke, biomass, heavy oil, or even natural gas. This is an abstract of a paper presented at the 2010 AIChE Annual Meeting (Salt Lake City, UT 11/7-12/2010)....

Subtask 3.3 - Feasibility of Direct Coal Liquefaction in the Modern Economic Climate

Energy Technology Data Exchange (ETDEWEB)

Benjamin Oster; Joshua Strege; Marc Kurz; Anthony Snyder; Melanie Jensen

2009-06-15

Coal liquefaction provides an alternative to petroleum for the production of liquid hydrocarbon-based fuels. There are two main processes to liquefy coal: direct coal liquefaction (DCL) and indirect coal liquefaction (ICL). Because ICL has been demonstrated to a greater extent than DCL, ICL may be viewed as the lower-risk option when it comes to building a coal liquefaction facility. However, a closer look, based on conversion efficiencies and economics, is necessary to determine the optimal technology. This report summarizes historical DCL efforts in the United States, describes the technical challenges facing DCL, overviews Shenhua's current DCL project in China, provides a DCL conceptual cost estimate based on a literature review, and compares the carbon dioxide emissions from a DCL facility to those from an ICL facility.

Burning test on a storage drum filled with a mixture of sodiumnitrate and bitumen

International Nuclear Information System (INIS)

Knotik, K.; Leichter, P.; Spalek, K.

1979-01-01

A burning test on a common storage drum filled with a mixture of sodiumnitrate and bitumen was carried out to show the incinerability of said mixture. A 50 l mild steel drum was filled with 80,7 kg sodiumnitrate/bitumen-mixture. The drum was packed in a 200 l mild steel drum, the remaining space was filled with enough sand to cover the top of the inner drum with 15 cm of sand. The sand packing was then soaked with 70 l of light distillate fuel and ignited. The fuel burned until self-extinguishing occurred. 30 % (22,2 l) of the fuel was burned. 0,7 % of the energy potential was absorbed in the sand layer. The highest measured temperature was 34 0 C at the top of the test drum. It can be concluded, that even under severe external actions the ignition temperature of 400 0 C for bitumen/waste mixtures cannot be reached, providing correct technical storage conditions, which means that the void space in the cavities is filled with unburnable absorbing material like sand or salt. (author)

1170-MW(t) HTGR-PS/C plant application study report: tar sands oil recovery application

International Nuclear Information System (INIS)

Rao, R.; McMain, A.T. Jr.

1981-05-01

This report summarizes a study to apply an 1170-MW(t) high-temperature gas-cooled reactor - process steam/cogeneration (HTGR-PS/C) to tar sands oil recovery and upgrading. The raw product recovered from the sands is a heavy, sour bitumen; upgrading, which involves coking and hydrodesulfurization, produces a synthetic crude (refinable by current technology) and petroleum coke. Steam and electric power are required for the recovery and upgrading process. Proposed and commercial plants would purchase electric power from local utilities and obtain from boilers fired with coal and with by-product fuels produced by the upgrading. This study shows that an HTGR-PS/C represents a more economical source of steam and electric power

Dating of authigenic clays related to igneous intrusions in Hunter Valley Coals

International Nuclear Information System (INIS)

Zwingmann, H.

2000-01-01

The Sydney Basin is composed mainly of Permian and Triassic marine and non-marine clastic sedimentary strata together with economically significant coal deposits and volumetrically minor igneous rocks. Many of these igneous rocks are also economically significant not only for their use in the construction industry but also for their deleterious effects on coal mining, particularly in underground mines utilising longwall extraction systems. Igneous activity in the Sydney Basin ranges from Early Permian to Tertiary in age and although episodic in nature, activity was unlikely to have ceased for periods of more than approximately 10 million years (Carr and Facer 1980; Embleton et al. 1982). Dating of the time of emplacement of igneous rocks using the K-Ar isotopic system is a relatively straightforward procedure if suitable analytical facilities and samples of appropriate, fresh, primary minerals are available. In the case of intrusions in coal seams, however, the occurrence of fresh, primary minerals is very rare due to widespread alteration produced by interaction between the igneous rock and fluids in the coal seam. This interaction produces a variety of secondary minerals with most primary minerals and glass being altered to clays (mainly kaolinite) and carbonates. Consequently, relatively few isotopic dates for intrusions into coal seams have been determined. A detailed study of several hundred samples of igneous rocks from the Sydney Basin found only six samples of intrusions into coal seams that were suitable for conventional K-Ar dating (Carr and Facer 1980). Techniques for K-Ar dating of authigenic illite, developed in response to the need by the petroleum industry to understand the timing of diagenesis in petroleum source-rocks and reservoirs, are now well established (Clauer and Chaudhuri 1995). As part of a larger project on the impact of igneous intrusions on coal mining and the alienation of coal reserves, a preliminary investigation of the timing of

production and cost of cold patch road mats with bitumen extracted

African Journals Online (AJOL)

Jamiu

This paper reports the production of bituminous road mats with bitumen sourced from the Nigerian Tar sand, recycled .... scrap tires are produced every year, which makes the disposal of ..... particles will be round or nearly round and will pass.

Future petroleum energy resources of the world

Science.gov (United States)

Ahlbrandt, T.S.

2002-01-01

and gas endowment estimates. Whereas petroleum resources in the world appear to be significant, certain countries such as the United States may run into import deficits, particularly oil imports from Mexico and natural gas from both Canada and Mexico. The new assessment has been used as the reference supply case in energy supply models by the International Energy Agency and the Energy Information Agency of the Department of Energy. Climate energy modeling groups such as those at Stanford University, Massachusetts Institute of Technology, and others have also used USGS estimates in global climate models. Many of these models using the USGS estimates converge on potential oil shortfalls in 2036-2040. However, recent articles using the USGS (2000) estimates suggest peaking of oil in 2020-2035 and peaking of non-OPEC (Organization of Petroleum-Exporting Countries) oil in 2015-2020. Such a short time framework places greater emphasis on a transition to increased use of natural gas; i.e., a methane economy. Natural gas in turn may experience similar supply concerns in the 2050-2060 time frame according to some authors. Coal resources are considerable and provide significant petroleum potential either by extracting natural gas from them, by directly converting them into petroleum products, or by utilizing them to generate electricity, thereby reducing natural gas and oil requirements by fuel substitution. Non-conventional oil and gas are quite common in petroleum provinces of the world and represent a significant resources yet to be fully studied and developed. Seventeen non-conventional AU including coal-bed methane, basin-center gas, continuous oil, and gas hydrate occurrences have been preliminarily identified for future assessment. Initial efforts to assess heavy oil deposits and other non-conventional oil and gas deposits also are under way.

Bitumen rubber asphalt mix testing for South African pavement design method

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2011-07-01

Full Text Available The South Africa National Road Agency Ltd has entered into a research and laboratory testing agreement with the CSIR to support the revision of the South African Pavement Design Method (SAPDM). The research includes characterising a bitumen...

The History of Petroleum Pollution in Malaysia; Urgent Need for Integrated Prevention Approach

Directory of Open Access Journals (Sweden)

Mahyar Sakari

2010-01-01

Full Text Available Petroleum pollution is known as point and non-point source of contaminations in the environment. A major class of petroleum contaminant is groups of compounds consist of two or more fused benzene rings called polycyclic aromatic hydrocarbons (PAHs that are carcinogenic, mutagenic and toxic. Source identification of petroleum pollution is necessary to prevent pollution entry into the environment. Eight sedimentary cores were obtained from developed and developing areas around Peninsular Malaysia to investigate the historical profile of PAHs, their characteristics and its possible origins. The results showed that the PAHs concentrations varied from very minimum to 2400 ng/g d. w. in average quarter century intervals. Most of the studied locations showed high contribution of PAHs from combusted fuel, coal, biomasses and wood materials except for the southern part of Peninsular Malaysia in which revealed dominance of petroleum products. The findings indicate that PAHs are delivered from different intermediate materials such as asphalt, street dust, vehicular emission and crankcase oil. However, there has been a decline of PAHs input into the marine environment in recent years; petroleum is shown to be a significant cause of marine pollution since the second quarter of 20th century. An overview on sourced materials of petroleum pollution indicates multi-approach necessity toward pollution control, regardless of concentration and possible degradation processes. Various sectors both governmental and non-governmental are needed for prevention and control of petroleum pollution where different sources apparently contribute to the pollution generation process.

The composition of acids in bitumen and in products from saponification of kerogen: Investigation of their role as connecting kerogen and mineral matrix

Energy Technology Data Exchange (ETDEWEB)

Razvigorova, M.; Budinova, T.; Tsyntsarski, B.; Petrova, B. [Bulgarian Academy of Sciences, Institute of Organic Chemistry, 1113 Sofia, Acad. Bonchev Str., bl. 9 (Bulgaria); Ekinci, E. [ISIK University, Kumbaba Mevkii, 34980 Istanbul (Turkey); Atakul, H. [Istanbul Technical University, Department of Chemical Engineering, Maslak, 34469 Istanbul (Turkey)

2008-11-03

In order to obtain more information and to understand the nature of relation between organic and mineral matter in oil shales, the compositions of soluble bitumen fractions obtained by extraction from Bulgarian oil shales before and after demineralization with 10% HCl, concentrated HF, and a HF/HCl mixture were investigated. The four extracts were quantitatively examined by IR and {sup 1}H NMR spectroscopy. The investigation of isolated acidic material of the bitumen fractions showed that the fatty acids are present in bitumen fractions as free acids, esters and salts. The amount of free acids in bitumen is very small. The dominant part of bitumen acids is associated with mineral components of the oil shales as well as part of them is included in the mineral matrix, and can be separated only after deep demineralization. The kerogen of the oil shales, obtained after separation of the bitumen fractions and mineral components, was subjected to saponification in order to determine the amount of acids, bound as esters to the kerogen matrix. The major components found were n-carboxylic, {alpha},{omega}-di-carboxylic, and aromatic acids. The connection of kerogen with mineral components is accomplished by the participation of carboxylic and complicated ester bonds. Experimental data for the composition of bitumen acids give evidence that algae and terrestrial materials are initial sources in the formation of soluble organic matter of Bulgarian oil shale. (author)

Coal liquefaction and gas conversion contractors review conference: Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-11-01

This volume contains 55 papers presented at the conference. They are divided into the following topical sections: Direct liquefaction; Indirect liquefaction; Gas conversion (methane conversion); and Advanced research liquefaction. Papers in this last section deal mostly with coprocessing of coal with petroleum, plastics, and waste tires, and catalyst studies. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Phase-Separation Characteristics of Bitumen and their Relation to Damage-Healing

NARCIS (Netherlands)

Nahar, S.N.

2016-01-01

During the service life of flexible asphalt pavements, asphalt concrete degrades due to traffic loading and environmental conditions like temperature, rain, oxidation, ultraviolet-radiation from the sun. All these environmental factors have adverse effects on the performance of bitumen, which is the

Mechanical properties of millet husk ash bitumen stabilized soil block

African Journals Online (AJOL)

This study presents an investigation into the improvement of strength and durability properties of lateritic soil blocks using Millet Husk Ash (MHA) and Bitumen as additives so as to reduce its high cost and find alternative disposal method for agricultural waste. The lateritic soil samples were selected and treated with 0%, ...

Technology of Anticorrosive Protection of Steel Constructions by Coatings Based on Rapid-Hardening Bitumen-Latex Emulsion

Directory of Open Access Journals (Sweden)

Nykyforchyn, H.M.

2016-01-01

Full Text Available The recipes of rapid-hardening bitumen-latex emulsions and coatings on its base are created, in-laboratory tests of their physical, chemical and anticorrosive properties are carried out. The technology of anticorrosive protection and the installation technical documentation for making of aqueous bitumen-latex emulsion is developed, installation is mounted and a pilot lot of rapid-hardening emulsion is produced. Experimental-industrial approbation of the technology of coating formation on pipes in oil and gas industry is carried out.

Experimental data on compressive strength and durability of sulfur concrete modified by styrene and bitumen.

Science.gov (United States)

Dehestani, M; Teimortashlu, E; Molaei, M; Ghomian, M; Firoozi, S; Aghili, S

2017-08-01

In this data article experimental data on the compressive strength, and the durability of styrene and bitumen modified sulfur concrete against acidic water and ignition are presented. The percent of the sulfur cement and the gradation of the aggregates used are according to the ACI 548.2R-93 and ASTM 3515 respectively. For the styrene modified sulfur concrete different percentages of styrene are used. Also for the bitumen modified sulfur concrete, different percentages of bitumen and the emulsifying agent (triton X-100) are utilized. From each batch three 10×10×10 cm cubic samples were casted. One of the samples was used for the compressive strength on the second day of casting, and one on the twenty-eighth day. Then the two samples were put under the high pressure flame of the burning liquid gas for thirty seconds and their ignition resistances were observed. The third sample was put into the acidic water and after twenty eight days immersion in water was dried in the ambient temperature. After drying its compressive strength has been evaluated.

Black out - The post-petroleum era has started; Black out - L'apres-petrole a commence

Energy Technology Data Exchange (ETDEWEB)

Enderlin, S.

2009-07-01

The predictable shortage of petroleum resources raises up some worrying questions: how can we get rid of petroleum? What will be our life without petroleum? Will we have enough energy tomorrow to keep the same way of life as today? With what new energy sources tomorrow's world will turn? The author has travelled the world from the Americas to Asia and from Europe to the Persian Gulf to find the leads of the after-petroleum era. From the Chinese coal to the US ethanol, from the nuclear comeback to the Scandinavian innovations, this inquiry makes the world tour of projects, ideas and solutions. First world energy consumer and squanderer, the US hold a prominent place in the energy revolution that Barack Obama election will speed up. In Europe, Germany, Spain and Denmark have taken a serious lead in the green energies race, while China has become recently the first world power of greenhouse gas emissions. (J.S.)

Cogeneration Technology Alternatives Study (CTAS). Volume 6: Computer data. Part 1: Coal-fired nocogeneration process boiler, section A

Science.gov (United States)

Knightly, W. F.

1980-01-01

Various advanced energy conversion systems (ECS) are compared with each other and with current technology systems for their savings in fuel energy, costs, and emissions in individual plants and on a national level. About fifty industrial processes from the largest energy consuming sectors were used as a basis for matching a similar number of energy conversion systems that are considered as candidates which can be made available by the 1985 to 2000 time period. The sectors considered included food, textiles, lumber, paper, chemicals, petroleum, glass, and primary metals. The energy conversion systems included steam and gas turbines, diesels, thermionics, stirling, closed cycle and steam injected gas turbines, and fuel cells. Fuels considered were coal, both coal and petroleum based residual and distillate liquid fuels, and low Btu gas obtained through the on-site gasification of coal. Computer generated reports of the fuel consumption and savings, capital costs, economics and emissions of the cogeneration energy conversion systems (ECS's) heat and power matched to the individual industrial processes are presented for coal fired process boilers. National fuel and emissions savings are also reported for each ECS assuming it alone is implemented.

INTER-PHASE CONTACTS IN BITUMEN-MINERAL SYSTEMS AND THEIR STRENGTHENING

Directory of Open Access Journals (Sweden)

Ya. N. Kovalev

2014-01-01

Full Text Available Presently bitumen-mineral materials (including asphalt-concrete comprise nearly 98 % for construction of expensive road pavement. Large resources of local minerals (quartz sand and industrial wastes in the form of used molding sand (foundry by-product are widely applied for reduction of their cost. Such approach is economically and ecologically reasonable but it requires its justification because an adhesion interaction in the bitumen-quartz substrate system (with SiO2 more than 95 % is rather poor in natural state and due to water action it is still more decreasing. In this connection an objective necessity arises to modify significantly technology of bitumen-mineral compositions for ensuring reliability of road pavements while using silicon components.All the ideas pertaining to strengthening of adhesion bonds in the “quartz mineral substrate - bitumen” system are traditionally of physical and chemical nature and they presuppose mainly usage of colloidal chemistry methods. The paper considers the matter on the basis of molecular kinetic theory of matter taking into account the fact that there is absence of generally accepted calculations for intermolecular interactions of components in the SiO2 - organic matrix material system.As a theoretical supposition the following well-known regulatory principle in physics is used: as every atom or molecular have its own electromagnetic field then action of external electromagnetic fields initiates their interaction that leads to excitement of electrons, deformations and rupture of chemical bonds. Literature analysis shows that the existing electric bonds between components of the SiO2 - organic matrix material system provide the possibility to apply various electro-physical methods having an effect on these components with the purpose to strengthen their adhesion interaction.The paper investigates matters for determination of bond energy during physical adsorption and adhesion in the SiO2 - organic

Energy consumption and greenhouse gas emissions in the recovery and extraction of crude bitumen from Canada’s oil sands

International Nuclear Information System (INIS)

Nimana, Balwinder; Canter, Christina; Kumar, Amit

2015-01-01

Highlights: • A model to estimate energy consumption and GHG emissions in oil sands is presented. • The model is developed from fundamental engineering principles. • Cogeneration in the oil sands has the ability to offset GHG emissions. • The effect of key parameters is investigated through a sensitivity analysis. - Abstract: A model – FUNNEL-GHG-OS (FUNdamental ENgineering PrinciplEs-based ModeL for Estimation of GreenHouse Gases in the Oil Sands) was developed to estimate project-specific energy consumption and greenhouse gas emissions (GHGs) in major recovery and extraction processes in the oil sands, namely surface mining and in situ production. This model estimates consumption of diesel (4.4–7.1 MJ/GJ of bitumen), natural gas (52.7–86.4 MJ/GJ of bitumen) and electricity (1.8–2.1 kW h/GJ of bitumen) as fuels in surface mining. The model also estimates the consumption of natural gas (123–462.7 MJ/GJ of bitumen) and electricity (1.2–3.5 kW h/GJ of bitumen) in steam assisted gravity drainage (SAGD), based on fundamental engineering principles. Cogeneration in the oil sands, with excess electricity exported to Alberta’s grid, was also explored. Natural gas consumption forms a major portion of the total energy consumption in surface mining and SAGD and thus is a main contributor to GHG emissions. Emissions in surface mining and SAGD range from 4.4 to 7.4 gCO 2 eq/MJ of bitumen and 8.0 to 34.0 gCO 2 eq/MJ of bitumen, respectively, representing a wide range of variability in oil sands projects. Depending upon the cogeneration technology and the efficiency of the process, emissions in oil sands recovery and extraction can be reduced by 16–25% in surface mining and 33–48% in SAGD. Further, a sensitivity analysis was performed to determine the effects of key parameters on the GHG emissions in surface mining and SAGD. Temperature and the consumption of warm water in surface mining and the steam-to-oil ratio (SOR) in SAGD are major parameters

Evolution of sulfur speciation in bitumen through hydrous pyrolysis induced thermal maturation of Jordanian Ghareb Formation oil shale

Science.gov (United States)

Birdwell, Justin E.; Lewan, Michael; Bake, Kyle D.; Bolin, Trudy B.; Craddock, Paul R.; Forsythe, Julia C.; Pomerantz, Andrew E.

2018-01-01

Previous studies on the distribution of bulk sulfur species in bitumen before and after artificial thermal maturation using various pyrolysis methods have indicated that the quantities of reactive (sulfide, sulfoxide) and thermally stable (thiophene) sulfur moieties change following consistent trends under increasing thermal stress. These trends show that sulfur distributions change during maturation in ways that are similar to those of carbon, most clearly illustrated by the increase in aromatic sulfur (thiophenic) as a function of thermal maturity. In this study, we have examined the sulfur moiety distributions of retained bitumen from a set of pre- and post-pyrolysis rock samples in an organic sulfur-rich, calcareous oil shale from the Upper Cretaceous Ghareb Formation. Samples collected from outcrop in Jordan were subjected to hydrous pyrolysis (HP). Sulfur speciation in extracted bitumens was examined using K-edge X-ray absorption near-edge structure (XANES) spectroscopy. The most substantial changes in sulfur distribution occurred at temperatures up to the point of maximum bitumen generation (∼300 °C) as determined from comparison of the total organic carbon content for samples before and after extraction. Organic sulfide in bitumen decreased with increasing temperature at relatively low thermal stress (200–300 °C) and was not detected in extracts from rocks subjected to HP at temperatures above around 300 °C. Sulfoxide content increased between 200 and 280 °C, but decreased at higher temperatures. The concentration of thiophenic sulfur increased up to 300 °C, and remained essentially stable under increasing thermal stress (mg-S/g-bitumen basis). The ratio of stable-to-reactive+stable sulfur moieties ([thiophene/(sulfide+sulfoxide+thiophene)], T/SST) followed a sigmoidal trend with HP temperature, increasing slightly up to 240 °C, followed by a substantial increase between 240 and 320 °C, and approaching a constant value (∼0.95) at

Methods for differentiating identity and sources of mixed petroleum pollutants in the environment

International Nuclear Information System (INIS)

Kaplan, I.R.; Alimi, H.; Lee, R.P.

1993-01-01

When crude or refined oil products enter the environment they begin to degrade by numerous microbiological or physical processes. The result of such changes is to alter the molecular composition of the product so that its source is unrecognizable by application of conventional EPA-type methodology. Numerous methods have been devised in the petroleum exploration industry to characterize source rock bitumens and reservoir hydrocarbons. A modification of these methods has been successfully applied at the authors company to identify the source of the fugitive hydrocarbons. For mildly altered products a statistical comparison is made using pattern recognition of the n-alkane distribution between C 10 -C 35 for heavy products and C 3 -C 10 for the gasoline range products. For highly altered products, a search is made for complex organic molecules that have undergone the least alteration, which include long chain polynuclear aromatic hydrocarbons and the polycyclic paraffinic hydrocarbons. These biomarker compounds have many isomeric forms which help characterize their sources. Elemental composition; especially sulfur, vanadium and nickel, and other transition and base metals help differentiate crude oil from refined products. Lead alkyls and MTBE are especially useful in determining residence time of gasoline products in soil and ground water. Petroporphyrin characterization can help differentiate crude oil from heavy refined oils or fluids. Stable isotope ratios are particularly useful for differentiating sources of highly altered petroleum products

Issue of fossil fuel resources and coal technology strategy for the 21st century - toward the globalization

Energy Technology Data Exchange (ETDEWEB)

Ando, K. [Japan Coal Energy Center, Tokyo (Japan)

2001-03-01

The President of the Japan Coal Energy Centre gives an outlook on coal demand worldwide and particularly in Asia as a whole and Japan, and outlines the present day environmental concerns concerning coal. World reserves of coal, petroleum, natural gas and uranium are compared. The huge resources of coal may not be realized due to difficulty of development in both technical and economic terms. The 'triangle strategy' to resolve problems of supply and the environment is outlined - this considers the relationship between resources (supply) and utilization (demand); between resources and environment; and between utilization and environment. Technical tasks to tackle to exploit coal are listed. These include: advance in technology for resource exploration; improvement in refining and storing low-grade coal; establishing a highly efficient mining system; promoting of clean coal technology; recovery of coalbed methane; and CO{sub 2} fixation. 6 figs., 1 tab.

Breaking through the bitumen upgrading barriers with the UOP Uniflex Process

Energy Technology Data Exchange (ETDEWEB)

Gillis, D. [UOP LLC, Des Plaines, IL (United States)

2009-07-01

High costs and environmental concerns are some of the challenges facing bitumen upgrading. In addition, yields from conventional process such as coking and ebullated bed hydrocracking are much lower than desired. As such, there is a need for processes that can maximize conversion and selectively produce transportation boiling range products, particularly distillates. There are both technical and financial challenges in providing a reliable high-conversion technology. UOP has developed the UOP Uniflex Process, a commercially based high-conversion residue upgrading process that selectively converts residues from conventional crude oils and bitumen to transportation fuels and high quality synthetic crude oil. The unique features of this technology were described along with commercialization background. Recent advances being developed by UOP under the AERI Hydrocarbon Upgrading Demonstration Program were also described, with particular reference to catalyst design, engineering design and residue by-product utilization. This presentation also outlined UOP's latest flow scheme options for use with existing upgrading technologies. tabs., figs.

Effect of hydrated lime and cement on moisture damage of recycled mixtures with foamed bitumen and emulsion

OpenAIRE

Nosetti, R.A.; Pérez Jiménez, Félix Edmundo; Martínez Reguero, Adriana Haydée; Miró Recasens, José Rodrigo

2016-01-01

Cold recycling with foamed bitumen can be used as a sustainable and cost-effective rehabilitation technique. This paper focuses on the evaluation of the resistance to the water action in mixtures with reclaimed asphalt pavement (RAP) and foamed bitumen by means of indirect tensile test, comparing the effect of two active fillers: cement and hydrated lime. Additionally, mixtures recycled with RAP and asphalt emulsions were also tested in order to compare the response of both technologies. Resu...

Characterization and utilization of hydrotreated products produced from the Whiterocks (Utah) tar sand bitumen-derived liquid

Energy Technology Data Exchange (ETDEWEB)

Tsai, C.H.; Longstaff, D.C.; Deo, M.D.; Hanson, F.V.; Oblad, A.G.

1991-12-31

The bitumen-derived liquid produced in a 4-inch diameter fluidized-bed reactor from the mined and crushed ore from the Whiterocks tar sand deposit has been hydrotreated in a fixed-bed reactor. The purpose was to determine the extent of upgrading as a function of process operating variable. A sulfided nickel-molybendum on alumina hydrodenitrogenation catalyst was used in all experiments. Moderately severe operating conditions were employed; that is, high reaction temperature (617--680 K) high reactor pressure (11.0--17.1 MPa) and low liquid feed rate (0.18--0.77 HSV); to achieve the desired reduction in heteroatom content. Detailed chemical structures of the bitumen-derived liquid feedstock and the hydrotreated total liquid products were determined by high resolution gas chromatography - mass spectrometry analyses. The compounds identified in the native bitumen included isoprenoids; bicyclic, tricycle, and tetracyclic terpenoids; steranes; hopanes; and perhydro-{beta}-carotenes. In addition, normal and branched alkanes and alkenes and partially dehydrogenated hydroaromatics were identified in the bitumen-derived liquid. The dominant pyrolysis reactions were: (1) the dealkylation of long alkyl side chains to form {alpha} - and isoolefins; and (2) the cleavage of alkyl chains linking aromatic and hydroaromatic clusters. Olefinic bonds were not observed in the hydrotreated product and monoaromatic hydrocarbons were the predominant aromatic species. The properties of the jet fuel fractions from the hydrotreated products met most of the jet fuel specifications. The cetane indices indicated these fractions would be suitable for use as diesel fuels.

Characterization and utilization of hydrotreated products produced from the Whiterocks (Utah) tar sand bitumen-derived liquid

Energy Technology Data Exchange (ETDEWEB)

Tsai, C.H.; Longstaff, D.C.; Deo, M.D.; Hanson, F.V.; Oblad, A.G.

1991-01-01

The bitumen-derived liquid produced in a 4-inch diameter fluidized-bed reactor from the mined and crushed ore from the Whiterocks tar sand deposit has been hydrotreated in a fixed-bed reactor. The purpose was to determine the extent of upgrading as a function of process operating variable. A sulfided nickel-molybendum on alumina hydrodenitrogenation catalyst was used in all experiments. Moderately severe operating conditions were employed; that is, high reaction temperature (617--680 K) high reactor pressure (11.0--17.1 MPa) and low liquid feed rate (0.18--0.77 HSV); to achieve the desired reduction in heteroatom content. Detailed chemical structures of the bitumen-derived liquid feedstock and the hydrotreated total liquid products were determined by high resolution gas chromatography - mass spectrometry analyses. The compounds identified in the native bitumen included isoprenoids; bicyclic, tricycle, and tetracyclic terpenoids; steranes; hopanes; and perhydro-{beta}-carotenes. In addition, normal and branched alkanes and alkenes and partially dehydrogenated hydroaromatics were identified in the bitumen-derived liquid. The dominant pyrolysis reactions were: (1) the dealkylation of long alkyl side chains to form {alpha} - and isoolefins; and (2) the cleavage of alkyl chains linking aromatic and hydroaromatic clusters. Olefinic bonds were not observed in the hydrotreated product and monoaromatic hydrocarbons were the predominant aromatic species. The properties of the jet fuel fractions from the hydrotreated products met most of the jet fuel specifications. The cetane indices indicated these fractions would be suitable for use as diesel fuels.

Ontario's petroleum legacy : the birth, evolution and challenges of a global industry

International Nuclear Information System (INIS)

Gray, E.

2008-01-01

This book provided a historical account of Ontario's role in the global oil industry, from the coming in of the first wells at Oil Springs in the mid-19th century when the primary fuel sources were wood, coal, and water. In 1858, oil seeps in Enniskillen Township, Lambton County, Ontario revealed the existence of petroleum, which encouraged the first drilling of wells and the development of the global industry. The book explored issues related to imperialism, resource development, local history and the colonial land policies surrounding the oil boom. Details of the Petrolia oil discovery were included along with the accomplishments of the entrepreneurs who were instrumental in developing the petroleum industry in Ontario. The major elements surrounding the development of Canada's oil and gas industry were presented, beginning with the coal-oil-refining industry which paved the way for the development of the oil industry; the early oilmen from Oil Springs and Petrolia who drilled for oil; the development of the oil and gas industry's position today as a major strength of the Canadian economy; and the environmental and climate change issues that currently confront the industry. After 150 years, the oil fields at Petrolia and Oil Springs still produce commercial quantities of crude oil from at least 650 active wells. refs., figs

Fine particle coal as a source of energy in small-user applications

Energy Technology Data Exchange (ETDEWEB)

Mitchell, T M

1986-01-01

The potential savings are reviewed which are involved in the combustion of coal-water mixtures in atmospheric fluidized bed combustors and pulsed combustors for space and water heating in residential structures in the USA. Savings in 'present value' operating costs of heating systems which would be achieved by switching from oil to coal are presented for New England, the Middle Atlantic and East North Central sub-regions at different interest rates from 10 to 30%, and assuming low rates of growth in petroleum prices. These savings define the extra amount of money the user would be prepared to pay to purchase a coal slurry system. At a purchase price of 2500 dollars, this option would only be profitable for commercial users.

Influence of bitumen type on cracking resistance of asphalt mixtures used in pavement overlays

Science.gov (United States)

Jaskula, P.; Szydlowski, C.; Stienss, M.

2018-05-01

Cracking is one of the predominant distresses occurring in flexible pavements, especially in old pavements that were rehabilitated with an asphalt overlay. In such cases asphalt mixtures should be designed to ensure high resistance to reflective cracking because new asphalt layers are exposed to existing cracks of the old pavement. The nature of these cracks can be various (transverse, longitudinal as well as crazy cracking). One factor that minimizes this type of distress is the proper mix design process, which should involve selection of specific bitumen binder and mineral mix gradation. However, still there is no universally adopted laboratory test method that would allow to clearly assess resistance of asphalt mixtures to reflective cracking. This paper describes the usage of one of the devices developed to test asphalt mixtures in terms of such distress – Texas Overlay Tester. For this test, samples prepared in laboratory conditions (i.e. compacted with the use of Superpave Gyratory Compactor) as well as obtained in the field (by core drilling) can be used. The results are obtained not only quickly and easily, but also with sufficient repeatability. The described method characterizes both crack initiation and crack propagation properties of asphalt mixtures. In this work one type of mineral mixture was tested with 4 different types of bitumen (one neat bitumen, two ordinary polymer-modified and one polymer-modified with high polymer content). For selected cases extra additives (rubber and loose fibres) were also tested. In total, six asphalt mixtures were tested. A ranking of the used binders was created on the basis of the results in order to conclude which bitumen would ensure the best performance characteristics in terms of reflective cracking. The results have clearly shown that deliberate choice of the binder used in the asphalt mixture for the overlay will significantly improve its reflective cracking resistance or even fatigue resistance.

Coal and nuclear power should supplement oil - International Chamber of Commerce

International Nuclear Information System (INIS)

Gomez, B.

1982-01-01

The views of the International Chamber of Commerce on world energy planning are noted. The Chamber has suggested that governments should expedite and clarify environmental and safety regulations for nuclear energy and coal, both important and acceptable energy sources which offer abundant and economic means to reduce dependence on petroleum. Economic advantages and environmental hazards are considered

Energy conservation potential in China’s petroleum refining industry: Evidence and policy implications

International Nuclear Information System (INIS)

Lin, Boqiang; Xie, Xuan

2015-01-01

Highlights: • A long-term equilibrium relationship of energy demand in China’s petroleum refining industry is established. • The sectoral energy conservation potential is evaluated by using scenarios analysis. • Energy prices, enterprise scale, R and D investment and ownership structure affect electricity intensity. • Future policy for energy conservation in China’s petroleum refining industry is suggested. - Abstract: China is currently the second largest petroleum refining country in the world due to rapid growth in recent years. Because the petroleum refining industry is energy-intensive, the rapid growth in petroleum refining and development caused massive energy consumption. China’s urbanization process will guarantee sustained growth of the industry for a long time. Therefore, it is necessary to study the energy conservation potential of the petroleum industry. This paper estimates the energy conservation potential of the industry by applying a cointegration model to investigate the long-run equilibrium relationship between energy consumption and some factors such as energy price, enterprise scale, R and D investment and ownership structure. The results show that R and D investment has the greatest reduction impact on energy intensity, and the growth of market participants (i.e. the decline of the share of state-owned companies) can improve energy efficiency of this industry. Under the advanced energy-saving scenario, the accumulated energy conservation potential will reach 230.18 million tons of coal equivalent (tce). Finally, we provide some targeted policy recommendations for industrial energy conservation

Investment in the Western Hemisphere energy market

International Nuclear Information System (INIS)

Gillam, P.J.

1991-01-01

This paper reports that the main characteristics of Western Hemisphere energy markets are well known to those in the energy industry. The United States sits in the northern half of the hemisphere, importing more and more oil from the rest of the world. Brazil, with a market one-tenth of the size of the United Sates, sits in the southern half of the hemisphere, importing less and less oil from the rest of the world. Venezuela sits in the center with an eye to the future as a long-term player in the world petroleum industry. Venezuela has 6 or 7 percent of the world's known conventional petroleum reserves, plus an uncountable bitumen resource which is now being commercialized as Orimulsion, a low-emission substitute for coal. The United States is circled by major producing countries with smaller exports, such as Mexico and Canada, and there are smaller producing or consuming countries of which Colombia is the largest exporter and Argentian the largest importer. The United States dominates the numbers. Half of British Petroleum's (BP) investments have been in the energy industry of the Western Hemisphere. We are maintaining that proportion, but opportunities are becoming more difficult to find

Chemical modification of bitumen heavy ends and their non-fuel uses

Energy Technology Data Exchange (ETDEWEB)

Moschopedis, S.E.; Speight, J.G.

1976-01-01

Bitumen asphaltenes undergo a variety of simple chemical conversions. For example, asphaltenes can be oxidized, sulfonated, sulfomethylated, halogenated, and phosphorylated. The net result is the introduction of functional entities into the asphaltene structure which confers interesting properties on the products for which a variety of uses are proposed.

Characterization of the viscoelastic behavior of the pure bitumen grades 10/20 and 35/50 with macroindentation and finite element computation

KAUST Repository

Hamzaoui, Rabah

2013-06-23

In this article, we present an identification procedure that allows the determination of the viscoelasticity behavior of different grades of pure bitumen (bitumen 35/50 and bitumen 10/20). The procedure required in the first stage a mechanical response based on macroindentation experiments with a cylindrical indenter. A finite element simulation was performed in the second stage to compute the mechanical response corresponding to a viscoelasticity model described by three mechanical parameters. The comparison between the experimental and numerical responses showed a perfect matching. In addition, the identification procedure helped to discriminate between different bitumens characterized by different asphaltene and maltene contents. Finally, the developed procedure could be used as an efficient tool to characterize the mechanical behavior of the viscoelastic materials, thanks to the quantified relationship between the viscoleastic parameters and the force-penetration response. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3440-3450, 2013 Copyright © 2013 Wiley Periodicals, Inc.

Geothermal waste heat utilization from in situ thermal bitumen recovery operations.

Science.gov (United States)

Nakevska, Nevenka; Schincariol, Robert A; Dehkordi, S Emad; Cheadle, Burns A

2015-01-01

In situ thermal methods for bitumen extraction introduce a tremendous amount of energy into the reservoirs raising ambient temperatures of 13 °C to as high as 200 °C at the steam chamber edge and 50 °C along the reservoir edge. In essence these operations have unintentionally acted as underground thermal energy storage systems which can be recovered after completion of bitumen extraction activities. Groundwater flow and heat transport models of the Cold Lake, Alberta, reservoir, coupled with a borehole heat exchanger (BHE) model, allowed for investigating the use of closed-loop geothermal systems for energy recovery. Three types of BHEs (single U-tube, double U-tube, coaxial) were tested and analyzed by comparing outlet temperatures and corresponding heat extraction rates. Initial one year continuous operation simulations show that the double U-tube configuration had the best performance producing an average temperature difference of 5.7 °C, and an average heat extraction of 41 W/m. Given the top of the reservoir is at a depth of 400 m, polyethylene piping provided for larger extraction gains over more thermally conductive steel piping. Thirty year operation simulations illustrate that allowing 6 month cyclic recovery periods only increases the loop temperature gain by a factor of 1.2 over continuous operation. Due to the wide spacing of existing boreholes and reservoir depth, only a small fraction of the energy is efficiently recovered. Drilling additional boreholes between existing wells would increase energy extraction. In areas with shallower bitumen deposits such as the Athabasca region, i.e. 65 to 115 m deep, BHE efficiencies should be larger. © 2014, National Ground Water Association.

Distribution of clay minerals in the process streams produced by the extraction of bitumen from Athabasca oil sands

Energy Technology Data Exchange (ETDEWEB)

Kaminsky, H.A.W.; Etsell, T.H.; Ivey, D.G. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering; Omotoso, O. [Natural Resources Canada, Devon, AB (Canada). CETC

2009-02-15

The clay minerals present in the oil sands were studied with particular reference to how they are partitioned in bitumen ore during the extraction process. Bitumen production from surface-mined oil sands accounts for nearly two-thirds of the total bitumen production in Alberta. Every cubic meter of mined ore results in 1.3 cubic meters of mature fine tailings (MFT). The characteristic differences between the clay minerals that report to the froth versus the tailings streams were also examined to determine which minerals could impact different unit operations in the bitumen extraction process. X-ray diffraction and random powder samples were used to quantify the clay minerals. Particle size distribution and clay activity balances were also conducted. The degree of partitioning during the conditioning and flotation stages in a batch extractor was determined by the surface properties of the clay minerals. The water-continuous tailings stream was separated into fine and coarse tailings fractions through sedimentation. The study showed that bitumen-clay interactions may be dominated by kaolinite or iron oxides. Clays are responsible for the poor settling behaviour of MFTs. The clay minerals present in the oil sands include illite, illite-smectite, kaolinite, kaolinite-smectite, and chlorite. The close proximity of the tailings ponds to the Athabasca River and volatile organic compounds (VOCs) emission require that the ponds be reclaimed to a natural landscape before mine closure. In addition to its impact on fine tailings reclamation, clay mineralogy plays a role in extraction froth flotation and emulsion stability during froth treatment. The mineralogy of the froth solids was found to be different from the mineralogy of the middlings and tailings solids. 39 refs., 6 tabs., 6 figs.

Low severity conversion of activated coal. Final report

Energy Technology Data Exchange (ETDEWEB)

Hirschon, A.S.; Ross, D.S.

1990-01-01

The results suggest that coal contains regions with structural components significantly reactive under the hydrothermal environment. Although the specific mechanism for this process remains to be developed, this activity is reminiscent of findings in studies of accelerated maturation of oil shale, where hydrothermal treatment (hydrous pyrolysis) leads to the production of petroleum hydrocarbons. In line with what has been seen in the oil shale work, the pretreatment-generated hydrocarbons and phenols appear to represent a further or more complete maturation of some fraction of the organic material within the coal. These observations could have an impact in two areas. The first is in the area of coal structure, where immature, reactive regions have not been included in the structures considered at present. The second area of interest is the more practical one of conversions to coal liquids and pyrolytic tars. It seems clear that the hydrothermal pretreatment changes the coal in some manner that favorably affects the product quality substantially and, as in the CO/water liquefaction case, favorably affects the yields. The conversions of coals of lower rank, i.e., less mature coals, could particularly benefit in terms of both product quality and product quantity. The second portion of this project also shows important benefits to coal conversion technology. It deals with synthesizing catalysts designed to cleave the weak links in the coal structure and then linking these catalysts with the pretreatment methods in Task 2. The results show that highly dispersed catalysts can effectively be used to increase the yields of soluble material. An important aspect of highly dispersed catalysts are that they can effectively catalyze coal conversion even in poor liquefaction solvents, thus making them very attractive in processes such as coprocessing where inexpensive liquefaction media such as resids are used.

An Embryonic Field of Study: The Aquatic Fate and Toxicity of Diluted Bitumen.

Science.gov (United States)

Alsaadi, Ftoon; Hodson, Peter V; Langlois, Valerie S

2018-01-01

Canada has experienced a significant increase in the transport of diluted bitumen (dilbit), a predominant oil sands product that combines bitumen with diluents derived from oil-gas condensates and other proprietary compounds. The proportion of diluent and the chemical composition of dilbit vary to meet seasonal transport requirements. While the toxic effects of a variety of crude and refined oils are well-studied, the toxicity of dilbit to aquatic species is less well known. This focused review summarizes dilbit production, chemistry, and the few data on toxicity to aquatic species. These data suggest that un-weathered dilbit would cause effects on fish equivalent to those of conventional oils, but its toxicity may be lower, depending on interactions among test conditions, the behavior of dilbit added to water and the species tested.

Effect of waste plastic as modifier on thermal stability and degradation kinetics of bitumen/waste plastics blend

Energy Technology Data Exchange (ETDEWEB)

Naskar, M. [Rubber Technology Centre, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Chaki, T.K., E-mail: tapan@rtc.iitkgp.ernet.in [Rubber Technology Centre, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Reddy, K.S. [Department of Civil Engineering, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India)

2010-09-20

Different modified bituminous binders are used in pavement construction for improved durability and for enhanced performance in resisting cracking and permanent deformation of bituminous layers. Waste plastics, whose disposal is a matter of concern, have been used successfully for modifying bitumen. This paper reports the thermogravimetric studies conducted on waste plastic modified bituminous binders. Modified bituminous binders prepared using different plastic contents (0-7 wt% by weight of bitumen) were investigated. The activation energies were determined from thermogravimetric analysis (TGA) data using Kissinger and the Flynn-Wall-Ozawa methods, which do not require knowledge of the reaction mechanism. Modified bitumen (WPMB5) with 5 wt% plastic was found to have the highest thermal stability compared to other binders investigated. Differential scanning calorimetry (DSC) studies were carried out to find crystalline melting temperature and fusion enthalpy. Rheological parameters of modified binders prepared with different plastic contents also suggest that the 5 wt% plastic content is expected to yield optimal performance.

Effect of waste plastic as modifier on thermal stability and degradation kinetics of bitumen/waste plastics blend

International Nuclear Information System (INIS)

Naskar, M.; Chaki, T.K.; Reddy, K.S.

2010-01-01

Different modified bituminous binders are used in pavement construction for improved durability and for enhanced performance in resisting cracking and permanent deformation of bituminous layers. Waste plastics, whose disposal is a matter of concern, have been used successfully for modifying bitumen. This paper reports the thermogravimetric studies conducted on waste plastic modified bituminous binders. Modified bituminous binders prepared using different plastic contents (0-7 wt% by weight of bitumen) were investigated. The activation energies were determined from thermogravimetric analysis (TGA) data using Kissinger and the Flynn-Wall-Ozawa methods, which do not require knowledge of the reaction mechanism. Modified bitumen (WPMB5) with 5 wt% plastic was found to have the highest thermal stability compared to other binders investigated. Differential scanning calorimetry (DSC) studies were carried out to find crystalline melting temperature and fusion enthalpy. Rheological parameters of modified binders prepared with different plastic contents also suggest that the 5 wt% plastic content is expected to yield optimal performance.

Effect of nitrogen and phosphate limitation on utilization of bitumen ...

African Journals Online (AJOL)

The degradation of bitumen was found to be associated with the production of carbon (IV) oxide, natural gas and oil. As a result of using nitrogen limited and phosphate limited media, 1750 and 1250 cm3 of gas and 0.95 and 0.85 g/l of oil were obtained respectively. Nitrogen and phosphate limitation have profound effect on ...

Application of organic-geochemistry, coal-petrology and isotope-geochemistry to facies-analysis and hydrocarbon exploration in the NE-Paris Basin (Trias-Lias Luxemburg)

International Nuclear Information System (INIS)

Flekken, P.M.

1978-01-01

Triassic and Liassic sediments of NE-Paris Basin (Luxemburg) were investigated by organic-geochemical, coal petrographical and isotope-geochemical methods. The objective was to characterize the stratigraphic stages and to investigate the facies relations between them with a view to possible hydrocarbon exploration. The sediments contain an average of 3.1% organic carbon, 413 ug/g extractable organic matter (bitumen) and 0.65% insoluble, isolatable organic particles which constitute part of the kerogen. The non-isolatable kerogen is 2.4% of the whole rock. (orig./BR) [de

Laboratory investigation of bitumen based on round robin DSC and AFM tests

NARCIS (Netherlands)

Soenen, H.; Besamusca, J.; Fischer, H.R.; Poulikakos, L.D.; Planche, J.P.; Das, P.K.; Kringos, N.; Grenfell, J.R.A.; Lu, X.; Chailleux, E.

2014-01-01

In the past years a wide discussion has been held among asphalt researchers regarding the existence and interpretation of observed microstructures on bitumen surfaces. To investigate this, the RILEM technical committee on nano bituminous materials 231-NBM has conducted a round robin study combining

Trace metals in heavy crude oils and tar sand bitumens

Energy Technology Data Exchange (ETDEWEB)

Reynolds, J.G.

1990-11-28

Fe, Ni, and V are considered trace impurities in heavy crude oils and tar sand bitumens. In order to understand the importance of these metals, we have examined several properties: (1) bulk metals levels, (2) distribution in separated fractions, (3) size behavior in feeds and during processing, (4) speciation as a function of size, and (5) correlations with rheological properties. Some of the results of these studies show: (1) V and Ni have roughly bimodal size distributions, (2) groupings were seen based on location, size distribution, and Ni/V ratio of the sample, (3) Fe profiles are distinctively different, having a unimodal distribution with a maximum at relatively large molecular size, (4) Fe concentrations in the tar sand bitumens suggest possible fines solubilization in some cases, (5) SARA separated fractions show possible correlations of metals with asphaltene properties suggesting secondary and tertiary structure interactions, and (6) ICP-MS examination for soluble ultra-trace metal impurities show the possibility of unexpected elements such as U, Th, Mo, and others at concentrations in the ppB to ppM range. 39 refs., 13 figs., 5 tabs.

Metabolites of the PAH diol epoxide pathway and other urinary biomarkers of phenanthrene and pyrene in workers with and without exposure to bitumen fumes.

Science.gov (United States)

Lotz, Anne; Pesch, Beate; Dettbarn, Gerhard; Raulf, Monika; Welge, Peter; Rihs, Hans-Peter; Breuer, Dietmar; Gabriel, Stefan; Hahn, Jens-Uwe; Brüning, Thomas; Seidel, Albrecht

2016-11-01

This study investigates the diol epoxide pathway of phenanthrene (PHE) together with phenolic metabolites of PHE and pyrene (PYR) in workers with and without exposure to bitumen fumes. The metabolite concentrations were determined in urine samples collected from 91 mastic asphalt workers and 42 construction workers as reference group before and after shift. During shift, vapours and aerosols of bitumen were measured according to a German protocol in the workers' breathing zone. The median concentration of vapours and aerosols of bitumen in mastic asphalt workers was 6.3 mg/m 3 . Metabolite concentrations were highest in post-shift urines of smokers with bitumen exposure and showed an increase during shift. The Spearman correlations between the creatinine-adjusted concentrations of metabolites and vapours and aerosols of bitumen in non-smokers were weak (e.g. sum of Di-OH-PYR: 0.28) or negligible (e.g. 1,2-PHE-diol: 0.08; PHE-tetrol: 0.12). Metabolites from the diol epoxide pathway of PHE were excreted in higher concentrations than phenolic metabolites (post-shift, non-smoking asphalt workers: 1,2-PHE-diol 2.59 µg/g crea vs. sum of all OH-PHE 1.87 µg/g crea). 1,2-PHE-diol was weakly correlated with PHE-tetrol (Spearman coefficient 0.30), an endpoint of the diol epoxide pathway. By contrast, we found a close correlation between the sum of 1,6-DiOH-PYR and 1,8-DiOH-PYR with 1-OH-PYR (Spearman coefficient 0.76). Most urinary PAH metabolites were higher after shift in bitumen-exposed workers, although the association with bitumen was weak or negligible likely due to the small PAH content. The additional metabolites of PHE and PYR complete the picture of the complex metabolic pathways. Nevertheless, none of the PAH metabolites can be considered to be a specific biomarker for bitumen exposure.

Tar bases in low-temperature coal tar

Energy Technology Data Exchange (ETDEWEB)

Sugiura, S; Ueno, H; Yokoyama, H

1951-01-01

Tar bases were extracted from three fractions, that boil below 260/sup 0/ at 260/sup 0/ to 280/sup 0/, and 280/sup 0/ to 330/sup 0/, respectively, of the low-temperature tar obtained by the carbonization of Ube coal in a Koppers' vertical retort at approximately 750/sup 0/. These were divided, respectively, into three groups, acetate-forming amine, HCl salt-forming bases (I), and CHCl/sub 3/-soluble bases (II), and further fractionally distilled. From the physical and chemical properties of the fractions thus obtained, it was concluded that low-temperature coal tar contained no low boiling pyridine homologues and that, besides higher homologues of pyridine, nonaromatic, more saturated, and less basic compounds of larger atomic weight and smaller refractive index, such as derivatives of pyrrole and indole, also existed as in crude petroleum.

Coal, the metamorphoses of an industry. The new geopolitics of the 21. century

International Nuclear Information System (INIS)

Martin-Amouroux, J.M.

2008-01-01

Coal consumption is growing up so fast and coal reserves are so abundant that coal might overtake petroleum in the future. The worldwide environment will not gain anything in this evolution except if 'clean coal' technologies make a significant jump. What is the driving force of this coal development? The pitfall encountered by nuclear energy and the rise of natural gas prices have been favorable conditions for the development of coal but they cannot hide the worldwide metamorphosis of coal industry. From China, undisputed world leader, to the USA, without omitting India, Russia and the big exporting countries (Australia, Indonesia, South Africa, Colombia), a new map is drawing up. In all these countries, coal companies are concentrating and internationalizing, open new strip mines and new commercial paths. The understanding of this metamorphosis has become one of the keys of the energy prospective and geopolitics of the 21. century. Content: 1 - entering the 21. century with the energy source of the 19. century?; 2 - consumption growth: new trends; 3 - the USA: the Saudi Arabia of coal; 4 - the unexpected rebirth of coal in Russia; 5 - China, world leader of coal industry; 6 - India and south-east Asia are entering the race; 7 - the rise of exporting industries; 8 - international markets and competitive dynamics of industries; 9 - advantage and drawbacks of coal during the coming decades; 10 - will clean coal technologies be ready on time?; 11 - technical appendix. (J.S.)

Changes in the composition and properties of Ashalchinskoye bitumen-saturated sandstones when exposed to water vapor

Science.gov (United States)

Korolev, E.; Eskin, A.; Kolchugin, A.; Morozov, V.; Khramchenkov, M.; Gabdelvalieva, R.

2018-05-01

Ashalchinskoye bitumen deposit is an experimental platform for testing technology of high-viscosity oil extraction from reservoir rocks. Last time for enhanced of oil recovery in reservoir used pressurization a water vapor with a temperature of ∼ 180 ° C (SAGD technology). However, what happens in sandstone reservoir is little known. We did a study of the effects of water vapor on the structural components of bitumen saturated sandstone. In paper were studied the rock samples at base condition and after one week exposure by water vapour. The thermal analysis showed that steaming helps to removes light and middle oil fractions with a boiling point up to 360 ° C from oil saturated sandstones. Content of heavy oil fractions virtually unchanged. Studying the composition of water extractions of samples showed that the process of aquathermolysis of oil is accompanied by a lowering of the pH of the pore solution from 7.4 to 6.5 and rise content in several times of mobile cations Ca2+, Mg2+ and HCO3 -, SO4 2- anions. Follows from this that the thermal steam effect by bitumen saturated sandstones leads to partial oxidation of hydrocarbons with to form a carbon dioxide. The source of sulfate ions were oxidized pyrite aggregates. Due to the increasing acidity of condensed water, which fills the pore space of samples, pore fluid becomes aggressive to calcite and dolomite cement of bitumen saturated sandstones. As a result of the dissolution of carbonate cement the pore fluid enriched by calcium and magnesium cations. Clearly, that the process is accompanied by reduction of contact strength between fragments of minerals and rocks. Resulting part of compounds is separated from the outer side of samples and falls to bottom of water vapor container. Decreasing the amount of calcite and dolomite anions in samples in a steam-treated influence is confirmed by X-Ray analysis. X-Ray analysis data of study adscititious component of rocks showed that when influenced of water vapor to

Extra heavy crudes and bitumens in the new EST technology

International Nuclear Information System (INIS)

Montanari, R.

2001-01-01

Strategic and market reasons dictate for the diversification of the supply sources. The huge reserves of extra heavy crudes and oil sands bitumen will provide the answer in this direction, but it is mandatory the availability of a suitable technology to process these poor quality feedstocks. EST Technology, developed by Snamprogetti and EniTecnologie, allows to get full conversion to produce high quality distillates [it

The role of the national petroleum company in petroleum development market

Energy Technology Data Exchange (ETDEWEB)

Lee, B J [Korea Energy Economics Institute, Euiwang (Korea, Republic of)

1997-08-01

The present century started with the creation of national petroleum companies, and it ends with those national petroleum companies exerting various types of efforts to increase the efficiency of their management. Especially, the efforts of these national petroleum companies are ever intensifying to adapt to new trends in the world petroleum market such as intensified competition, ever-deepening price unstableness, separation of structure between upstream and downstream portions, rapid development of petroleum development technologies, change of political systems and the demise of national borders, ever-increasing consciousness of environmental preservation, etc. Korea cannot be exempt from management rationalization efforts of national petroleum companies. Especially, Korea established its own national petroleum company in order to actively deal with these as its supply system is very weak. Therefore, the national petroleum company should create as many successful petroleum development businesses by actively carrying out petroleum development businesses domestically and overseas in order to establish a stable supply system of petroleum and to support the petroleum development businesses of civilian enterprises more effectively. The national petroleum company must, first of all, replace the bureaucracy with entrepreneurship. Esp., in order to enhance the efficiency of management, short- term outcome should not be emphasized over long-term tenure of petroleum development businesses, and excessive interference of government on the national petroleum company should be excluded. The entrepreneurship of the national petroleum company should be pursued in Positive-sum way, and its public image should be actively promoted through this. 35 refs., 11 figs., 32 tabs.

FY 2000 report on the basic survey to promote Joint Implementation, etc. Project on methane gas recovery use in the Donetsk coal field/coal mine; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Donetsk tanden tanko methane gas kaishu riyo keikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of getting petroleum substitution energy and reducing greenhouse effect gas emission, an investigational study was carried out of the project for methane gas recovery/utilization at the Donbassa coal mine in Ukraine. At the Donbassa coal mine, degassing by test boring is being conducted to reduce the gas emission at coal face for safety, but most of the gas is discharged into the air. In this project, the following were studied: degassing boring/gas induction from bore hole/measurement in gas induction pipe, gas recovery system combined with gas induction in flyash, and installation/operation of gas engine power generation facilities (1,710kW x 7 units) with exhaust heat recovery boiler using the recovered methane gas as fuel. The results obtained were the petroleum substitution amount of 31,000 toe/y and the amount of greenhouse effect gas reduction of 480,000 t/y. In the economical estimation, the initial investment amount was 3 billion yen, the profitability of the total investment used was 2.9%, and the internal earning rate was 6.5%. (NEDO)

Report on the achievements in the Sunshine Project in fiscal 1985. Studies on liquefying reaction of coals, and on reforming and utilizing the product; 1985 nendo sekitan no ekika hanno to seiseibutsu no kaishitsu riyo no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-03-01

Contents of the studies on coal liquefaction processes during fiscal 1985 are as follows: coal liquefying reaction using iron based catalysts and adding solvent-refined coal (SRC) into the solvent is carried out by using an autoclave to investigate changes in the liquefaction rate, solvent and SRC; coal hydrogenating reaction using iron based catalysts is performed by using a continuous liquefying equipment to discuss sedimentation and accumulation of the catalysts, coal types, and conversion rate; hydrogenation treatment using Ni-Mo based catalysts is given on residual products produced by the liquefaction to compare degree of lightening and cleanliness with the result in medium fraction; hydrogenation treatment is given on the medium fraction produced in a large process to investigate effects of the reforming treatment from the nature of the produced oil and compare the effects with the nature of oil produced from mixing the medium fraction of the coal liquefied oil with the corresponding fraction from petroleum; a combustion test using a diesel engine is performed on oil reformed and produced from the hydrogenation treatment of the medium fraction of the coal liquefied oil to discuss the reforming effect from the amount and nature of the waste gas; and the oil mixed of the medium fraction and the corresponding fraction in petroleum is evaluated on petroleum substitution performance by using the above test. (NEDO)

Microbial processes in the final repository, the silo part. Theoretical approach and preliminary experiments on the biodegradation of bitumen. Part 1

International Nuclear Information System (INIS)

Roffey, R.; Hjalmarsson, K.

1984-01-01

On Commission of SKBF/KBS the microbial processes that are likely to occur in the silo part of SFR, the final repository for medium- and low-level nuclear wastes, have been put together. The experimental studies concerning microbial degradation of bitumen are described. From a microbial point of view it is the biodegradation of bitumen that constitutes the greatest risk in the silo part of SFR. The degradation, aerobic as well as anaerobic, leads to production of carbon dioxide which might cause a decrease in pH to such an extent that hydrogen-gas producing corrosion of metal could occur. This production of gas can cause an increase in internal pressure of the repository. A culture of bacteria able to degrade bitumen aerobically has been enriched. Uptil now no culture degrading bitumen under anaerobic conditions have been obtained. When making a risk assessment of the SFR at the present time it is not possible to completely disregard the microbial activity. An account is also given for some international contacts in this area. 11 references

Petroleum supply monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

It's all about the bitumen : oilsands producers have the attention of the world

International Nuclear Information System (INIS)

Jaremko, D.

2005-01-01

Within 10 years, oilsands growth will make Canada the fifth largest oil producing country in the world, thereby greatly increasing Canada's political power. A review of oil sands development was presented, with reference to the way in which Steam Assisted Gravity Drainage (SAGD) has revolutionized the industry. Recent acquisitions have pointed to the growing level of international interest in the oilsands industry. Construction details of the Surmont project were discussed along with Devon Canada's SAGD project at Jackfish where about 100 well-pairs are expected to be drilled. Petrobank Energy and Resources is constructing its Whitesands project, which will employ the first field-scale application of the toe-to-heel air injection (THAI) recovery method which has lower operating costs and which uses less water and creates fewer greenhouse (GHG) emissions. The pilot was designed to produce up to 1800 barrels per day of partially upgraded bitumen. Details of CNRI's Horizon project were presented, including construction plans and schedules. Shell Canada's increased budget for the first expansion of the Athabasca Oilsands Project was reviewed with reference to their strategic decision to pre-build infrastructure for future expansions. Details of Suncor Energy's production goals were also reviewed, including details of new upgraders and applications. Syncrude's continuing expansions were discussed, as well as their current production levels. An outline of UTS Energy Corporation and Petro-Canada's plans concerning the Fort Hills Mining Project was presented, with details of the new BITMIN extraction process. It was noted that Imperial Oil has filed regulatory applications for the Kearl Oilsands Project, which have estimated total recoverable bitumen resources of 4.4 billion barrels. Husky Energy's Sunrise Project was discussed, as well as MEG Energy's regulatory approval for the first phase of the Christina Lake Regional Project. The Canadian Association of Petroleum

Environmental impact of Bitumen on soil, water and plant in Lodasa ...

African Journals Online (AJOL)

The presence of bitumen in Lodasa soil is fast eroding soil fertility in the area and has contributed immensely to low yield of Agricultural products. The use of organic fertilizer to boost soil fertility, relocation and resettlement of farmers to areas with high soil fertility and appropriate legislation to protect the rights of the native ...

Environmental issues of petroleum exploration and production: Introduction

Science.gov (United States)

Kharaka, Yousif K.; Dorsey, Nancy S.

2005-01-01

Energy is the lifeblood of our planet Earth, an essential commod- ity that powers the expanding global economy. Starting in the 1950s, oil and natural gas became the main sources of primary energy for the increasing world population, and this dominance is expected to continue for several more decades (Edwards, 1997; Energy Information Administration (EIA), 2004). In the United States, petroleum production started in 1859 when Drake's well was drilled near Titusville, Pennsylvania, and oil and natural gas currently supply approximately 63% of the energy consumption; forecasts indicate that by 2025, their use will increase by about 40% to 28.3 million bbl/day and to 31.4 tcf/yr (EIA, 2004). The clear benefits of petroleum consumption, however, can carry major environmental impacts that may be regional or global in scale, in- cluding air pollution, global climate change, and oil spills. This vol- ume of Environmental Geosciences, covering environmental impacts of petroleum exploration and production, does not address these major impacts directly because air pollution and global warming are issues related primarily to petroleum and coal uses, and major oil spills are generally attributed to marine petroleum transportation, such as the Exxon Valdez's 1989 spill of 260,000 bbl of oil into Prince William Sound, Alaska. Exploration for and production of petroleum, however, have caused local detrimental impacts to soils, surface and groundwa- ters, and ecosystems in the 36 producing states in the United States (Richter and Kreitler, 1993; Kharaka and Hanor, 2003). These im- pacts arose primarily from the improper disposal of some of the large volumes (presently estimated at 20 billion bbl/yr total pro- duced) of saline water produced with oil and gas, from accidental hydrocarbon and produced-water releases, and from abandoned oil wells that were orphaned or not correctly plugged (Kharaka et al., 1995; Veil et al., 2004). Impacts and ground-surface disturbances, in the order

Crude petroleum

International Nuclear Information System (INIS)

1990-01-01

Crude petroleum statistics by country of production, export values and import values from 1983 to 1988 are given. Table A.1 of the Annex includes free market prices and price indices for crude petroleum based on average of Dubai, United Kingdom Brent and Alaska N Slope crude prices (price expressed in dollars/barrel). The data sources are: Crude petroleum United Nations Statistical Office; OPEC Annual Statistical Bulletin, and Petroleum Economist. For trade the sources of data are: National trade statistics; United Nations international trade statistics; International Moneytary Fund (IMF); Organization of the Petroleum Exporting Countries (OPEC); UNCTAD secretariat estimates. Tabs

Petroleum

International Nuclear Information System (INIS)

Anon.

2000-01-01

Here are gathered the results of the year 1999 concerning the petroleum industry in France ('UFIP' data), the market quotations of crude oil, the prices of fuels in France and in Portugal and some news about the petroleum industry in Algeria (privatization, exploration-offshore, repurchase), in Iraq (exports, contracts with foreign companies), in Russian Federation (petroleum pipelines and oil ports constructions) and in Chad (production sharing, offshore sites discoveries). (O.M.)

Bitumen/Water Emulsions as Fuels for High-Speed Ci Engines Preliminary Investigations

DEFF Research Database (Denmark)

Schramm, Jesper; Sigvardsen, R.; Forman, M.

2003-01-01

Mixtures of bitumen and water, are cheap fuel alternatives for combustion engines. There are, however, several problems that have to be solved before these fuels can be applied in high-speed diesel engines. These are: - emulsion break up due to high temperature or high shear stress in the injection...

Petroleum Supply Monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in Indonesia; Kankyo chowagata sekitan riyo system kanosei chosa. Indonesia ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the coal of Indonesia, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/distribution/utilization and environmental problems, and analyzed the situation of the coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to work out a comprehensive master plan including Japan`s international cooperation for introducing the environmentally-friendly coal utilization system to Indonesia. Coal utilization systems, the introduction of which Indonesia should study in future, were picked up, according to the surveys in fiscal 1993 and 1994. In commercial/residential and small-scale industry sectors, needed is improvement of carbonization technology for production of coal carbonization briquette. Moreover, the introduction of bio-briquette should be studied in the future. In the power generation sector, studies should be made on the introduction of technology for SOx/NOx reduction and technology for coal ash treatment including the effective use of coal ash. For the introduction of coal boilers, the combustion mixed with bagasse, which is abundant in amount, is also necessary. In the coal production sector, coal preparation technology is studied, and a method to select the optimum process was proposed through the simulation. 76 figs., 43 tabs.

Effect of radio-oxidative ageing and pH on the release of soluble organic matter from bitumen

International Nuclear Information System (INIS)

Libert, M.F.; Walczak, I.

2000-01-01

Bitumen is employed as an embedding matrix for low and medium level radioactive wastes. An high impermeability and a great resistance against most of chemicals are two of main bitumen properties. These characteristics of bitumen confinement properties may be modified under environmental parameters during intermediate storage or deep repository such as radiations or the presence of water. The radio-oxidation induces an increase of the quantity of leached organic matter. The evolution of the soluble organic species release seems to be linear with the irradiation dose, as soon as the dose is higher than 20 kGy, and seems to be no dependant of the dose rate. The generation of water-soluble organic complexing agents can affect the integrity of the wasteform due to an increase of the radionuclides solubility. An increase of the quantity of leached organic matter is also observed in presence of alkaline solutions. Identified molecules, by GC/MS analysis, are aromatics like naphthalene, oxidised compounds like alcohols, linear carbonyls, aromatics, glycols and nitrogen compounds. (authors)

Isocyanate-functionalized castor oil as a novel bitumen modifier

OpenAIRE

Cuadri Vega, Antonio Abad; García Morales, Moisés; Navarro Domínguez, Francisco Javier; Partal López, Pedro

2013-01-01

The use of biomaterials from renewable sources in the synthesis of polyurethane-derived polymers is lately receiving great attention from social, environmental and economic standpoints. In this work, prepolymers having different -NCO/-OH ratio were synthesized, by reaction of 4,4´-diphenylmethane diisocyanate (MDI) with castor oil (CO), to be used as modifying agent of asphaltic bitumen. Reactions between MDI and CO, performed with -NCO/-OH molar ratios of 8:1 and 4:1, have led to suitable bi...

Present situation of the development of petroleum substitution energy (The UK); Sekiyu daitai energy kaihatsu no genjo (Eikoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the petroleum substitution energy in the U.K., the paper states measures taken for the development and introduction and the state of spread. Introduced were the U.K., energy policy described by energy field, petroleum and natural gas, coal, nuclear power, electric power, renewable energy (petroleum substitution energy), and the policy on energy conservation and the recent trend. Further, the paper took up the environmental policy relating to global warming which is an environmental problem in close connection with the energy industry and described the present status of exhaust gas such as acid rain gas and ozonospherial destruction gas, target for reduction of exhaust gas, and the present situation of exhaust gas at power plant. Explained were the positioning of and the measures for the petroleum substitution energy which was incorporated into a part of the energy policy in the U.K., especially the recent trend of obligation to use non-fossil fuel. First, the order of priority of the governmental policies was introduced, and then the NFFO order was described which was to give reliable fund base to the development toward the practical use of petroleum substitution energy. The paper also commented on recent topics on the state of the practical use of petroleum substitution energy. 2 figs., 7 tabs.

How Thermal Fatigue Cycles Change the Rheological Behavior of Polymer Modified Bitumen?

NARCIS (Netherlands)

Glaoui, B.; Merbouh, M.; Van de Ven, M.F.C.; Chailleux, E.; Youcefi, A.

2013-01-01

The paper deals with the problem of thermal fatigue cycles phenomenon, which affects the performance of flexible pavement. The purpose of the paper is to extent the knowledge on the rheology of polymer modified bitumen which was affected by cycles of thermal fatigue. The aim of this research is to

Experimental study of simultaneous Athabasca bitumen recovery and upgrading using ultradispersed catalysts injection

Energy Technology Data Exchange (ETDEWEB)

Hashemi, R.; Pereira, P. [University of Calgary (Canada)

2011-07-01

As the demand for oil is continuously increasing, the need for unconventional resources is rising. Oil extraction from bitumen and heavy oil reservoirs requires advanced techniques in order to decrease the viscosity of the oil. To increase the recovered original oil in place (OOIP) of a reservoir and decrease refining costs, new techniques to upgrade oil in situ are being developed. The current study investigates the use of ultra-dispersed (UD) submicronic catalysts to decrease oil viscosity. The experiment involved the injection of the catalyst and hydrogen gas in a sand pack saturated with Athabasca bitumen. Analysis was carried out by building recovery curves, and by comparing the oil recovery from the catalyzed process with that of catalyst-free processes. The study demonstrated that the oil recovered from the new technique had higher API gravity and lower viscosity, indicating the success of the in situ upgrading process.

Coal rank, distribution, and coalbed methane potential of the Lower Cretaceous Luscar Group, Bow River to Blackstone River, central Alberta foothills

Energy Technology Data Exchange (ETDEWEB)

Dawson, F M; Kalkreuth, W D

1994-12-31

Mapping data on Lower Cretaceous Luscar Group coals in the central Alberta foothills is presented. The coals outcrop in the Inner Foothills from the Bow River to the boundary between Alberta and British Columbia, north of Grande Cache. Both subsurface and surface mapping data is presented. The coal rank is highly variable and depends on sample location and depth, as established by vitrinite reflectance studies on trench samples and cuttings gathered from petroleum exploration wells. The conventional coal resource potential and the coalbed methane potential for the area are discussed with reference to the map sheets provided. 29 refs., 45 figs., 3 tabs., 3 apps.

Power technology complex for production of motor fuel from brown coals with power supply from NPPs

International Nuclear Information System (INIS)

Troyanov, M.F.; Poplavskij, V.M.; Sidorov, G.I.; Bondarenko, A.V.; Chebeskov, A.N.; Chushkin, V.N.; Karabash, A.A.; Krichko, A.A.; Maloletnev, A.S.

1998-01-01

With the present-day challenge of efficient use of low-grade coals and current restructuring of coal industry in the Russian Federation, it is urgent to organise the motor fuel production by the synthesis from low grade coals and heavy petroleum residues. With this objective in view, the Institute of Physics and Power Engineering of RF Minatom and Combustible Resources Institute of RF Mintopenergo proposed a project of a standard nuclear power technology complex for synthetic liquid fuel (SLF) production using fast neutron reactors for power supply. The proposed project has two main objectives: (1) Engineering and economical optimization of the nuclear power supply for SLF production; and (2) Engineering and economical optimization of the SLF production by hydrogenisation of brown coals and heavy petroleum residues with a complex development of advanced coal chemistry. As a first approach, a scheme is proposed with the use of existing reactor cooling equipment, in particular, steam generators of BN-600, limiting the effect on safety of reactor facility operation at minimum in case of deviations and abnormalities in the operation of technological complex. The possibility to exclude additional requirements to the equipment for nuclear facility cooling was also taken into account. It was proposed to use an intermediate steam-water circuit between the secondary circuit sodium and the coolant to heat the technological equipment. The only change required for the BN-600 equipment will be the replacement of sections of intermediate steam superheaters at the section of main steam superheaters. The economic aspects of synthetic motor fuel production proposed by the joint project depend on the evaluation of integral balances: thermal power engineering, chemical technology, the development of advanced large scale coal chemistry of high profitability; utilisation of ash and precious microelements in waste-free technology; production of valuable isotopes; radical solution of

Petroleum

International Nuclear Information System (INIS)

Anon.

2000-01-01

Here are briefly summarized 1)the OPEC decisions and their consequences concerning the production of petroleum in the world 2)some news about the petroleum industry in Chad and in Iraq 3)some news about the new pipelines constructed or to be constructed in the world 4)some news about the LPG industry (start of a LPG extraction unit in Argentina, legislation in France for LPG vehicles) 4)and some news about the petroleum distribution in France. (O.M.)

Coal char combustion under a CO{sub 2}-rich atmosphere: Implications for pulverized coal injection in a blast furnace

Energy Technology Data Exchange (ETDEWEB)

Borrego, A.G.; Casal, M.D. [Instituto Nacional del Carbon, CSIC. P.O. Box 73, 33080 Oviedo (Spain); Osorio, E.; Vilela, A.C.F. [Laboratorio de Siderurgia, DEMET/PPGEM - Universidade Federal do Rio Grande do Sul. P.O. Box 15021, 91501-970 Porto Alegre (Brazil)

2008-11-15

Pulverized coal injection (PCI) is employed in blast furnace tuyeres attempting to maximize the injection rate without increasing the amount of unburned char inside the stack of the blast furnace. When coal is injected with air through the injection lance, the resolidified char will burn in an atmosphere with a progressively lower oxygen content and higher CO{sub 2} concentration. In this study an experimental approach was followed to separate the combustion process into two distinct devolatilization and combustion steps. Initially coal was injected into a drop tube furnace (DTF) operating at 1300 C in an atmosphere with a low oxygen concentration to ensure the combustion of volatiles and prevent the formation of soot. Then the char was refired into the DTF at the same temperature under two different atmospheres O{sub 2}/N{sub 2} (typical combustion) and O{sub 2}/CO{sub 2} (oxy-combustion) with the same oxygen concentration. Coal injection was also performed under a higher oxygen concentration in atmospheres typical for both combustion and oxy-combustion. The fuels tested comprised a petroleum coke and coals currently used for PCI injection ranging from high volatile to low volatile bituminous rank. Thermogravimetric analyses and microscopy techniques were used to establish the reactivity and appearance of the chars. Overall similar burnouts were achieved with N{sub 2} and CO{sub 2} for similar oxygen concentrations and therefore no loss in burnout should be expected as a result of enrichment in CO{sub 2} in the blast furnace gas. The advantage of increasing the amount of oxygen in a reacting atmosphere during burnout was found to be greater, the higher the rank of the coal. (author)

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline E. Burgess Clifford; Andre' Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2006-09-17

This report summarizes the accomplishments toward project goals during the second six months of the third year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts and examination of carbon material, the use of a research gasoline engine to test coal-based gasoline, and modification of diesel engines for use in evaluating diesel produced in the project. At the pilot scale, the hydrotreating process was modified to separate the heavy components from the LCO and RCO fractions before hydrotreating in order to improve the performance of the catalysts in further processing. Characterization of the gasoline fuel indicates a dominance of single ring alkylcycloalkanes that have a low octane rating; however, blends containing these compounds do not have a negative effect upon gasoline when blended in refinery gasoline streams. Characterization of the diesel fuel indicates a dominance of 3-ring aromatics that have a low cetane value; however, these compounds do not have a negative effect upon diesel when blended in refinery diesel streams. Both gasoline and diesel continue to be tested for combustion performance. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Activated carbons have proven useful to remove the heavy sulfur components, and unsupported Ni/Mo and Ni/Co catalysts have been very effective for hydrodesulfurization. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Combustion and characterization of the latest fuel oil (the high temperature fraction of RCO

Technical evaluation of the ATI volume reduction and bitumen solidification topical report

International Nuclear Information System (INIS)

Henscheid, J.W.; Young, T.E.

1985-01-01

This report summarizes EG and G Idaho's review of the Associated Technologies Inorporated (ATI) topical report on a Volume Reduction and Bitumen Solidification System. The review evaluated compliance with pertinent codes, standards and regulations. The initial review was discussed with ATI, and all outstanding issues resolved before this final evaluation was made

Influence of the association of the EVA and NBR on the characteristics of modified bitumen

Science.gov (United States)

Bensaada, A.; Soudani, K.; Haddadi, S.; Saoula, S.

2015-03-01

Durability and the performance of pavement depend mainly on the characteristics of materials which change over time like all other organic substances. They are subject to significant changes due to environmental conditions during the different phases of use. In the present work we investigated experimentally the influence of the association of ethyl vinyl acetate polymer (EVA) with an industrial waste, acrylonitrile-butadiene rubber (NBR) on the modification of bitumen AC 35-50 and its rheological behavior. The incorporation of NBR and EVA in the bitumen improved its intrinsic characteristics (softening point, penetration and ductility). In addition to improving the characteristics of bituminous binders that will affect the durability of bituminous structures, the environment will be preserved by the recycling of industrial waste.

Characterization and Behavior of Cold Lake Blend and Western Canadian Select Diluted Bitumen Products

Science.gov (United States)

Unconventional diluted bitumen (dilbit) oil products present an increasing environmental concern because of extensive transport in North America, recent spills into aquatic habitats, and limited understanding of environmental fate and toxicity. Dilbits are blends of highly weathe...

Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the coal of the Philippines, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/development, the trend of coal import and domestic distribution, the coal utilization trend, and environmental problems, and analyzed the situation of coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to draw up a master plan for the introduction of the environmentally-friendly coal utilization system. As to the use of environmentally-friendly coal technology which should be adopted to the coal mining industry and commercial/residential sector, cited are the introduction of coal preparation technology and power transmission technology, and the development/spread of briquette as a firewood substituting fuel. In the electric power sector, the problem is the treatment of ash after combustion and the effective use. Relating to the treatment of flue gas, there is no installation at all of desulfurization facilities and denitrification facilities. In the cement industry sector, they wish to return fuel from heavy oil to coal. For it, it is necessary to study dust preventive measures. In the other sectors, coal hasn`t been used very much. An increase in coal demand is not expected also in the future, and big problems concerning coal haven`t occurred. 42 figs., 64 tabs.

Suggestive evidence on the origin of petroleum and oil shale

Energy Technology Data Exchange (ETDEWEB)

Jones, J C

1923-01-01

Oil shales and coals originated in fresh water muds that contained large amounts of spores, algae, and other nonwoody vegetable material. This organic debris was partly decomposed by bacterial action but not enough to increase the percentage of fats by removal of other plant substances. By contrast, petroleum was formed by thorough decomposition of nonfatty material in salt water. The main difference in bacterial action was due to differences in the saline content of the water in which the organic material was deposited. In fresh water, the amount of decay was small, whereas in salt water it was nearly complete.

Determination of oxygen, nitrogen, and silicon in Nigerian fossil fuels by 14 MeV neutron activation analysis

International Nuclear Information System (INIS)

Hannan, M.A.; Oluwole, A.F.; Kehinde, L.O.; Borisade, A.B.

2003-01-01

Classification, assessment, and utilization of coal and crude oil extracts are enhanced by analysis of their oxygen content. Values of oxygen obtained 'by difference' from chemical analysis have proved inaccurate. The oxygen, nitrogen, and silicon content of Nigerian coal samples, crude oils, bitumen extracts, and tar sand samples were measured directly using instrumental fast neutron activation analysis (FNAA). The total oxygen in the coal ranges from 5.20% to 23.3%, in the oil and extracts from 0.14% to 1.08%, and in the tar sands from 38% to 47%. The nitrogen content in the coal ranges from 0.54% to 1.35%, in the crude oil and bitumen extracts from ≤ 0.014% to 0.490%, and in the tar sands from 0.082% to 0.611%. The silicon content in the coal ranges from 1.50% to 8.86%; in the oil and the bitumen extracts it is <1%, and in the tar sands between 25.1% and 37.5%. The results show that Nigerian coals are mostly sub-bituminous. However, one of the samples showed bituminous properties as evidenced by the dry ash-free (daf) percent of carbon obtained. This same sample indicated a higher ash content resulting in a comparatively high percentage of silicon. In oils and tar sands from various locations, a comparison of elements is made. (author)

Unconventional Energy Resources: 2015 Review

Energy Technology Data Exchange (ETDEWEB)

Collaboration: American Association of Petroleum Geologists, Energy Minerals Division

2015-12-15

This paper includes 10 summaries for energy resource commodities including coal and unconventional resources, and an analysis of energy economics and technology prepared by committees of the Energy Minerals Division of the American Association of Petroleum Geologists. Unconventional energy resources, as used in this report, are those energy resources that do not occur in discrete oil or gas reservoirs held in structural or stratigraphic traps in sedimentary basins. Such resources include coalbed methane, oil shale, U and Th deposits and associated rare earth elements of industrial interest, geothermal, gas shale and liquids, tight gas sands, gas hydrates, and bitumen and heavy oil. Current U.S. and global research and development activities are summarized for each unconventional energy resource commodity in the topical sections of this report, followed by analysis of unconventional energy economics and technology.

Integral migration and source-term experiments on cement and bitumen waste forms

International Nuclear Information System (INIS)

Ewart, F.T.; Howse, R.M.; Sharpe, B.M.; Smith, A.J.; Thomason, H.P.; Williams, S.J.; Young, M.

1986-01-01

This is the final report of a programme of research which formed a part of the CEC joint research project into radionuclide migration in the geosphere (MIRAGE). This study addressed the aspects of integral migration and source term. The integral migration experiment simulated, in the laboratory, the intrusion of water into the repository, the leaching of radionuclides from two intermediate-level waste-forms and the subsequent migration through the geosphere. The simulation consisted of a source of natural ground water which flowed over a sample of waste-form, at a controlled redox potential, and then through backfill and geological material packed in columns. The two waste forms used here were cemented waste from the WAK plant at Karlsruhe in the Federal Republic of Germany and bitumenized intermediate concentrates from the Marcoule plant in France. The soluble fission products such as caesium were rapidly released from the cemented waste but the actinides, and technetium in the reduced state, were retained in the waste-form. The released of all nuclides from the bitumenized waste was very low

A single-equation study of US petroleum consumption: The role of model specificiation

International Nuclear Information System (INIS)

Jones, C.T.

1993-01-01

The price responsiveness of US petroleum consumption began to attract a great deal of attention following the unexpected and substantial oil price increases of 1973-74. There have been a number of large, multi-equation econometric studies of US energy demand since then which have focused primarily on estimating short run and long run price and income elasticities of individual energy resources (coal, oil, natural gas ampersand electricity) for various consumer sectors (residential, industrial, commercial). Following these early multi-equation studies there have been several single-equation studies of aggregate US petroleum consumption. When choosing an economic model specification for a single-equation study of aggregate US petroleum consumption, an easily estimated model that will provide unbiased price and income elasticity estimates and yield accurate forecasts is needed. Using Hendry's general-to-simple specification search technique and annual data to obtain a restricted, data-acceptable simplification of a general ADL model yielded GNP and short run price elasticities near the consensus estimates, but a long run price elasticity substantially smaller than existing estimates. Comparisons with three other seemingly acceptable simple-to-general models showed that popular model specifications often involve untested, unacceptable parameter restrictions. These models may also demonstrate poorer forecasting performance. Based on results, the general-to-simple approach appears to offer a more accurate methodology for generating superior forecast models of petroleum consumption and other energy use patterns

Research on the technology of constructing a protection with joint use of no-fines concrete and bitumen

Directory of Open Access Journals (Sweden)

Mikhasek Andrey

2017-01-01

Full Text Available To build a bank slope protection of a hydraulic structure, a technology is proposed that involves building a framework of no-fines concrete and pouring it with hot bituminous materials. Implementation of this technology requires conducting a research on bitumen penetration into the protection plate body. The research involved developing models of non-stationary filtration under varied bitumen viscosity. The research involved experimental observation in laboratory environment. Models of movement of a variable viscosity liquid in a porous medium were proposed, and their study in laboratory environment allowed for identifying the depth of penetration, which is an important result to solve engineering objectives.

Bitumen coating as a tool for improving the porosity and chemical stability of simulated cement-waste forms

International Nuclear Information System (INIS)

Saleh, H.M.

2010-01-01

Coating process of simulated cement-based waste form with bitumen was evaluated by performing physical and chemical experimental tests. X-ray diffraction (X-RD), Fourier transform infrared spectroscopy (FT-IR) and electron microscope investigations were applied on coated and non-coated simulated waste forms. Experimental results indicated that coating process improved the applicable properties of cement-based waste form such as porosity and leachability. Diffusion coefficients and leach indecies of coated specimens were calculated and show acceptable records. It could be stated that coating cemented waste form by bitumen emulsion, isolate the radioactive contaminants, thus reduces their back release to surrounding and in consequently save the environment proper and safe

Thermal alterations of organic matter in coal wastes from Upper Silesia, Poland

Science.gov (United States)

Misz-Kennan, Magdalena

2010-01-01

Self-heating and self-combustion are currently taking place in some coal waste dumps in the Upper Silesian Coal Basin, Poland, e.g. the dumps at Rymer Cones, Starzykowiec, and the Marcel Coal Mine, all in the Rybnik area. These dumps are of similar age and self-heating and combustion have been occurring in all three for many years. The tools of organic petrography (maceral composition, rank, etc.), gas chromatography-mass spectrometry, and proximate and ultimate analysis are used to investigate the wastes. Organic matter occurs in quantities up to 85 vol.%, typically a few to several vol.%, in the wastes. All three maceral groups (vitrinite, liptinite, and inertinite) are present as unaltered and variously-altered constituents associated with newly-formed petrographic components (bitumen expulsions, pyrolytic carbon). The predominant maceral group is vitrinite with alterations reflected in the presence of irregular cracks, oxidation rims and, rarely, devolatilisation pores. In altered wastes, paler grey-vitrinite and/or coke dominates. The lack of plasticity, the presence of paler-coloured particles, isotropic massive coke, dispersed coked organic matter, and expulsions of bitumens all indicate that heating was slow and extended over a long time. Macerals belonging to other groups are present in unaltered form or with colours paler than the colours of the parent macerals. Based on the relative contents of organic compounds, the most important groups of these identified in the wastes are n-alkanes, acyclic isoprenoids, hopanes, polycyclic aromatic hydrocarbons (PAHs) and their derivatives, phenol and its derivatives. These compounds occur in all wastes except those most highly altered where they were probably destroyed by high temperatures. These compounds were generated mainly from liptinite-group macerals. Driven by evaporation and leaching, they migrated within and out of the dump. Their presence in some wastes in which microscopically visible organic matter is

Fiscal 1999 research cooperation project report. Research cooperation on coal liquefaction technology; 1999 nendo sekitan ekika gijutsu ni kansuru kenkyu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research cooperation project result on coal liquefaction technology. Cooperative FS was made on coal liquefaction technology of Indonesian coal as petroleum substituting energy. To obtain the basic data necessary for the FS, study was made on the applicability of Indonesian natural minerals as catalytic materials. Promising low-cost abundant Soroako Limonite ore showed a high catalytic activity for liquefaction reaction of Banko coal, and an excellent grindability. Improved BCL process including hydrogenation process was promising for production of high-quality coal liquid superior in storage stability with less nitrogen and sulfur contents. Survey was made on the general conditions of Tanjung Enim area including South Banko coal field concerned, and the geological features and coal seam of South Banko coal field which is composed of 3 seams including coal deposits of 6.35 hundred million tons. To study the marketability of coal liquid, survey was made on the current situation of oil, oil product standards, and blendability of coal liquid. Hydrogen for the liquefaction process can be obtained by coal gasification. (NEDO)

Influence of the co-firing on the leaching of trace pollutants from coal fly ash

Energy Technology Data Exchange (ETDEWEB)

Maria Izquierdo; Natalia Moreno; Oriol Font; Xavier Querol; Esther Alvarez; Diano Antenucci; Henk Nugteren; Yolanda Luna; Constantino Fernandez-Pereira [Institute of Earth Sciences ' Jaume Almera' (CSIC), Barcelona (Spain)

2008-08-15

The (co)-firing of low-cost alternative fuels is expected to increase in the forthcoming years in the EU because of the economic and environmental benefits provided by this technology. This study deals with the impact of the different coal/waste fuel ratio of the feed blend on the mineralogy, the chemical composition and especially on the leaching properties of fly ash. Different blends of coal, petroleum coke, sewage sludge, wood pellets, coal tailings and other minor biomass fuels were tested in PCC (pulverised coal combustion) and FBC (fluidized bed combustion) power plants. The co-firing of the studied blends did not drastically modify the mineralogy, bulk composition or the overall leaching of the fly ash obtained. This suggests that the co-firing process using the alternative fuels studied does not entail significant limitations in the re-use or management strategies of fly ash. 34 refs., 4 figs., 3 tabs.

Outlook and Challenges for Chinese Coal

Energy Technology Data Exchange (ETDEWEB)

Aden, Nathaniel T.; Fridley, David G.; Zheng, Nina

2008-06-20

inextricably entwined with China's economy in its current mode of growth. Ongoing dependence on coal reduces China's ability to mitigate carbon dioxide emissions growth. If coal demand remains on its current growth path, carbon dioxide emissions from coal combustion alone would exceed total US energy-related carbon emissions by 2010. Broadening awareness of the environmental costs of coal mining, transport, and combustion is raising the pressure on Chinese policy makers to find alternative energy sources. Within China's coal-dominated energy system, domestic transportation has emerged as the largest bottleneck for coal industry growth and is likely to remain a constraint to further expansion. China is short of high-quality reserves, but is producing its best coal first. Declining quality will further strain production and transport. Transporting coal to users has overloaded the train system and dramatically increased truck use, raising transport oil demand. Growing international imports have helped to offset domestic transport bottlenecks. In the long term, import demand is likely to exceed 200 mt by 2025, significantly impacting regional markets. The looming coal gap threatens to derail China's growth path, possibly undermining political, economic, and social stability. High coal prices and domestic shortages will have regional and global effects. Regarding China's role as a global manufacturing center, a domestic coal gap will increase prices and constrain growth. Within the Asia-Pacific region, China's coal gap is likely to bring about increased competition with other coal-importing countries including Japan, South Korea, Taiwan, and India. As with petroleum, China may respond with a government-supported 'going-out' strategy of resource acquisition and vertical integration. Given its population and growing resource constraints, China may favor energy security, competitiveness, and local environmental protection over global climate

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

Petroleum Marketing Monthly (PPM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o. b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

Petroleum 2006. Statistical elements

International Nuclear Information System (INIS)

2007-06-01

This document gathers in 5 parts, the main existing statistical data about petroleum industry in France and in the rest of the world, together with an insight on other energy sources: 1 - petroleum in the French economy (petroleum and other energies, petroleum and transports, petroleum and energy in the industry, the residential and tertiary sectors, environment: 42 pages); 2 - the French petroleum industry (exploration, production, foreign trade, transports, refining, storage, petrochemistry: 66 pages); 3 - the French market of petroleum products (evolution of sales by product and detail by region for the past year: 38 pages); 4 - prices and taxes of petroleum products (world prices and rates for crude and refined products, evolution of fret rates, retail prices and French taxes: 28 pages); 5 - petroleum in the world (world energy production and consumption, detailed petroleum activity by main areas and for the main countries: 112 pages). (J.S.)

Freeze-Thaw Performance and Moisture-Induced Damage Resistance of Base Course Stabilized with Slow Setting Bitumen Emulsion-Portland Cement Additives

Directory of Open Access Journals (Sweden)

Mojtaba Shojaei Baghini

2015-01-01

Full Text Available Freeze-thaw (FT cycles and moisture susceptibility are important factors influencing the geotechnical characteristics of soil-aggregates. Given the lack of published information on the behavior of cement-bitumen emulsion-treated base (CBETB under environmental conditions, especially freezing and thawing, this study investigated the effects of these additives on the CBETB performance. The primary goal was to evaluate the resistance of CBETB to moisture damage by performing FT, Marshall conditioning, and AASHTO T-283 tests and to evaluate the long-term stripping susceptibility of CBETB while also predicting the liquid antistripping additives to assess the mixture’s durability and workability. Specimens were stabilized with Portland cement (0%–6%, bitumen emulsion (0%–5%, and Portland cement-bitumen emulsion mixtures and cured for 7 days, and their short- and long-term performances were studied. Evaluation results of both the Marshall stability ratio and the tensile strength ratio show that the additions of additives increase the resistance of the mixtures to moisture damage. Results of durability tests performed for determining the resistance of compacted specimens to repeated FT cycles indicate that the specimen with the 4% cement-3% bitumen emulsion mixture significantly improves water absorption, volume changes, and weight losses. This indicates the effectiveness of this additive as a road base stabilizer with excellent engineering properties for cold regions.

Characterization of coal-derived hydrocarbons and source-rock potential of coal beds, San Juan Basin, New Mexico and Colorado, U.S.A.

Science.gov (United States)

Rice, D.D.; Clayton, J.L.; Pawlewicz, M.J.

1989-01-01

.5 ppt), are chemically wetter (C1/C1-5 values range from 0.85 to 0.95), and contain less CO2 (< 2%). These gases are interpreted to have been derived from type III kerogen dispersed in marine shales of the underlying Lewis Shale and nonmarine shales of the Fruitland Formation. In the underlying Upper Cretaceous Dakota Sandstone and Tocito Sandstone Lentil of the Mancos Shale, another gas type is produced. This gas is associated with oil at intermediate stages of thermal maturity and is isotopically lighter and chemically wetter at the intermediate stage of thermal maturity as compared with gases derived from dispersed type III kerogen and coal; this gas type is interpreted to have been generated from type II kerogen. Organic matter contained in coal beds and carbonaceous shales of the Fruitland Formation has hydrogen indexes from Rock-Eval pyrolysis between 100 and 350, and atomic H:C ratios between 0.8 and 1.2. Oxygen indexes and atomic O:C values are less than 24 and 0.3, respectively. Extractable hydrocarbon yields are as high as 7,000 ppm. These values indicate that the coal beds and carbonaceous shales have good potential for the generation of liquid hydrocarbons. Voids in the coal filled with a fluorescent material that is probably bitumen is evidence that liquid hydrocarbon generation has taken place. Preliminary oil-source rock correlations based on gas chromatography and stable carbon isotope ratios of C15+ hydrocarbons indicate that the coals and (or) carbonaceous shales in the Fruitland Formation may be the source of minor amounts of condensate produced from the coal beds at relatively low levelsof thermal maturity (Rm=0.7). ?? 1989.

Coals to Newcastle: Will Alberta become a crude oil importer?

International Nuclear Information System (INIS)

Haessel, W.; Foley, D.J.

1991-01-01

The security of markets for Canadian heavy crude oil (HCO) under different conditions is examined. The emphasis of the study is on the conditions under which bitumen blend from Alberta could penetrate certain markets that have generally been identified as potential prospects. A secondary question concerns the cost reductions in bitumen production and upgrading that would be needed for bitumen blend and synthetic crude oil (SCO) to penetrate these same markets if long-term oil prices settle at US$18/bbl for Saudi light delivered to the USA Gulf Coast in 2010. A brief overview is first presented of some of the world and US factors that will affect the demand for Canadian HCO, with specific reference to the demand in the northern USA in 2010. The determination of the volume of HCO that can or will be processed at a refinery or a combination of refineries in a given market is then discussed. The cost and volume numbers for 2010 as provided in the National Energy Board's latest Canadian energy supply and demand forecast are used in the analysis. It is concluded that all traditional markets outside of the Canadian prairies could be lost if world oil prices stay below US$18/bbl for extended periods. At prices below US$17/bbl, bitumen producers would have trouble competing with imported crude oils in Edmonton unless bitumen production costs decline from current levels. The potential for bitumen production costs to decline enough for diluted bitumen to compete with US$18/bbl oil is better than the prospect for SCO costs to decrease enough to compete in eastern Canada or the northern USA at those price levels. 9 figs., 8 tabs

Influence of DAD-TA temperature-reducing additive on physical and mechanical properties of bitumen and compaction of asphalt concrete.

Science.gov (United States)

Yadykina, V. V.; Akimov, A. E.; Trautvain, A. I.; Kholopov, V. S.

2018-03-01

The paper is devoted to the use of DAD-TA temperature-reducing additive for the preparation and pouring of asphalt concrete mixes at reduced temperatures. It also shows positive influence of the modified bitumen on the efficiency of organo-mineral composite compaction at reduced temperatures. Physical and mechanical properties of asphalt concrete with the use of bitumen modified by DAD-TA additive including indicators characterizing road surfacing life are presented. Arguments to use this material from the point of view of its production technology and environmental impact are given.

Petroleum fiscality indicators

International Nuclear Information System (INIS)

2008-02-01

This document presents the different taxes imposed to petroleum products in France: domestic tax on petroleum products (TIPP) and added value tax (TVA). A comparison is made with the fiscality into effect in other European countries for some petroleum products. Then, the fiscality is detailed for the different petroleum products and automotive fuels with its regional modulations. Finally, the fiscal measures adopted in 2007 are detailed. They concern the transposition of the European directive 2003-96/CE into French right and some fiscal regime changes given to some economical sectors particularly penalized by the rise of petroleum energy prices in 2007. (J.S.)

Petroleum industry 1996

International Nuclear Information System (INIS)

1997-01-01

A survey on petroleum industry activities in France and in the world in 1996 is presented. The different parts and themes of the study are: evolution of the petroleum market (international and French markets, supply and demand, prices, mark-up and taxation in France and in Europe); activities in the petroleum industries (exploration and production, maritime transportation, inland transportation and storage, refining, quality of petroleum products and substitution fuels, oil distribution); environment and safety (refining, distribution and evolution of products, pipeline and maritime transportation, exploration and production); situation of the sector's companies (oil groups, para-petroleum French industry, scientific and technical research)

Petroleum industry in 2004

International Nuclear Information System (INIS)

2005-01-01

This document presents a detailed outlook of the petroleum industry in the world and more particularly in France in 2005: evolution of crude oil prices; petroleum exploration and production in the world and in France; the French para-petroleum and petroleum industry; the oil supplies; the refining activities; the evolution of products quality and the substitution fuels; the domestic transports, the storage and consumption of petroleum products; the fiscality, prices and distribution of petroleum products. (J.S.)

Improving Asphalt Mixture Performance by Partially Replacing Bitumen with Waste Motor Oil and Elastomer Modifiers

Directory of Open Access Journals (Sweden)

Sara Fernandes

2017-08-01

Full Text Available The environmental concern about waste generation and the gradual decrease of oil reserves has led the way to finding new waste materials that may partially replace the bitumens used in the road paving industry. Used motor oil from vehicles is a waste product that could answer that demand, but it can also drastically reduce the viscosity, increasing the asphalt mixture’s rutting potential. Therefore, polymer modification should be used in order to avoid compromising the required performance of asphalt mixtures when higher amounts of waste motor oil are used. Thus, this study was aimed at assessing the performance of an asphalt binder/mixture obtained by replacing part of a paving grade bitumen (35/50 with 10% waste motor oil and 5% styrene-butadiene-styrene (SBS as an elastomer modifier. A comparison was also made with the results of a previous study using a blend of bio-oil from fast pyrolysis and ground tire rubber modifier as a partial substitute for usual PG64-22 bitumen. The asphalt binders were tested by means of Fourier infrared spectra and dynamic shear rheology, namely by assessing their continuous high-performance grade. Later, the water sensitivity, fatigue cracking resistance, dynamic modulus and rut resistance performance of the resulting asphalt mixtures was evaluated. It was concluded that the new binder studied in this work improves the asphalt mixture’s performance, making it an excellent solution for paving works.

Bituminization of simulated PWR type reactor wastes, boric evaporator bottons and ion exchange resins, carried out in CNEN/SP using commercial bitumen available in the Brazilian market

International Nuclear Information System (INIS)

Grosche Filho, C.E.; Chandra, U.

1986-01-01

The first results of the study of bituminization of simulated PWR wastes, boric evaporator bottons and spent ion-exclange resins (OH - , H + ) and incinerated ash-wates are presented and discussed. The study consisted of characterization of the commercial bitumen, locally available and bitumen wastes products of varying whight compositions. The characterization was carried out using standard analysis methods of ABNT and ASTM, and included measurement of, penetration, softening point and flash point. In addition, the bitumen samples were analized for their resin and asphaltene contents. For leaching studies, wastes products of bitumen and resin loaded with 134 Cs were utilized. The method used was according to the ISO norms. The simulation of the industrial process was carried out using an extruder-evaporator typically used in the plastic industries offered by Industria de Maquinas Miotto Ltda., Sao Bernardo do Campo - SP. (Author) [pt

Basic Performance of Fibre Reinforced Asphalt Concrete with Reclaimed Asphalt Pavement Produced In Low Temperatures with Foamed Bitumen

Science.gov (United States)

Chomicz-Kowalska, Anna; Iwański, Mateusz M.; Mrugała, Justyna

2017-10-01

During the reconstruction of road pavements, the reclaimed asphalt pavement (RAP), which is obtained through milling of the worn out existing asphalt, is commonly used for producing new base courses in cold recycling processes. Two of these techniques are most popular: one using mineral-cement-emulsion mixes and one utilizing mineral cement mixes with foamed bitumen. Additionally, some amounts of RAP can be incorporated into traditional hot mix asphalt. The demand for energy efficient and environmentally friendly solutions however, results in a need for development of new techniques that would result in cheaper and more reliable solutions with smaller carbon footprint. The reduction of processing temperatures with simultaneous incorporation of reclaimed material is the most efficient way of obtaining these objectives, but it often results in the overall decrease of bituminous mix quality. The paper presents the possibility of using RAP for producing asphalt concrete in warm mix asphalt (WMA) production process by the use of foamed bitumen modified with Fischer-Tropsch synthetic wax and polymer-basalt fibers. Additionally, a series of reference mixtures were produced to investigate the effects of the additives and of the warm process. The carried out analyses and tests shown that the experimental warm mix asphalt produced with RAP and foamed bitumen returned satisfactory performance. The introduction of synthetic F-T wax in the warm foam bitumen mixes resulted in a significantly improved compaction levels and moisture and frost resistance and the addition of polymer-basalt fibers has further improved the permanent deformation resistance of the mixes. All of the designed and tested mixes have fulfilled the requirements for binding course asphalt concrete with medium traffic loads.

Co-liquefaction of micro algae with coal. 2; Bisai sorui to sekitan no kyoekika hanno. 2

Energy Technology Data Exchange (ETDEWEB)

Ueda, C.; Matsui, T.; Otsuki, M.; Ikenaga, N.; Suzuki, T. [Kansai University, Osaka (Japan). Faculty of Engineering

1996-10-28

For the removal and recycle of CO2, a global warming gas, utilization of photosynthesis by micro algae is investigated. Formed micro algae are decomposed into CO2, H2O and CH4 again, which does not result in the permanent fixation. For the effective utilization of these micro algae, creation of petroleum alternate energy was tried through the co-liquefaction of micro algae with coal. Were investigated influences of the reaction temperature during the co-liquefaction and influences of catalysts, such as Fe(CO)5-S, Ru(CO)12, and Mo(CO)6-S, which are effective for the coal liquefaction. Micro algae, such as chlorella, spirulina, and littorale, and Yallourn brown coal were tested. It was found that co-liquefaction of micro algae with coal can be successfully proceeded under the same conditions as the liquefaction of coal. The oil yield obtained from the co-liquefaction in the presence of Fe(CO)5-S, an effective catalyst for coal liquefaction, agreed appropriately with the arithmetical mean value from separate liquefaction of coal and micro algae. It was suggested that pyrrhotite, an active species for coal liquefaction, was sufficiently formed by increasing the addition of sulfur. 2 refs., 7 figs., 1 tab.

Coal background paper. Coal demand

International Nuclear Information System (INIS)

1997-01-01

Statistical data are presented on coal demands in IEA and OECD member countries and in other countries. Coal coaking and coaking coal consumption data are tabulated, and IEA secretariat's coal demand projections are summarized. Coal supply and production data by countries are given. Finally, coal trade data are presented, broken down for hard coal, steam coal, coking coal (imports and export). (R.P.)

19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

Chemical and physical hydrogeology of coal, mixed coal-sandstone and sandstone aquifers from coal-bearing formations in the Alberta Plains region, Alberta

International Nuclear Information System (INIS)

Lemay, T.G.

2003-09-01

With the decline of conventional oil and gas reserves, natural gas from coal (NGC) is an unconventional gas resource that is receiving much attention from petroleum exploration and development companies in Alberta. Although the volume of the NGC resource is large, there are many challenges facing NGC development in Alberta, including technical and economic issues, land access, water disposal, water diversion and access to information. Exploration and development of NGC in Alberta is relatively new, therefore there is little baseline data on which to base regulatory strategies. Some important information gaps have been filled through water well sampling in coal, mixed coal-sandstone and sandstone aquifers throughout Alberta. Analyses focused on the chemical and physical characteristics aquifers in use for domestic or agricultural purposes. Aquifer depths were generally less than 100 metres. Samples collected from Paskapoo-Scollard Formation, Horseshoe Canyon Formation and Belly River Group aquifers exceed Canadian water quality guideline values with respect to pH, sodium, manganese, chloride, chromium, sulphate, phenols and total dissolved solids. Pump tests conducted within the aquifers indicate that the groundwater flow is complicated. Water quality will have to be carefully managed to ensure responsible disposal practices are followed. Future studies will focus on understanding the chemical and biological process that occur within the aquifers and the possible link between these processes and gas generation. Mitigation and disposal strategies for produced water will also be developed along with exploration strategies using information obtained from hydrogeologic studies. 254 refs., 182 tabs., 100 figs., 3 appendices

Effect of non-homogeneous spatial distributions of surfactants on the stability of high-content bitumen-in-water emulsions

International Nuclear Information System (INIS)

Urbina-Villalba, German; Garcia-Sucre, Maximo

2000-01-01

In order to study the effects of non-homogeneous spatial distributions of surfactants on the drop size of high-content bitumen-in-water emulsions, a modification of a standard Brownian Dynamics algorithm was employed. The new algorithm is able to simulate the evolution of oil/water emulsions towards flocculation and coalescence. The simulation boxes contain 216 and 125 particles initially distributed in a homogeneous simple cubic arrangement, corresponding to bitumen/water volume fractions of 0.30 and 0.51, respectively. The particles interact through a DLVO potential dependent on the total surfactant concentration, spatial surfactant distribution, and the amount of surfactant adsorbed to the bitumen/water interface. As will be shown in this article, certain combinations of the referred variables can produce a wide variety of repulsive potentials between similar drops. The variation of the total number of drops with time does not obey the usual analytical formalisms developed for more diluted cases, and instead, a simple exponential decrease of the number of drops with time is found. Such behavior has already been confirmed by experiment. Some similarities between the present results and those previously published for more diluted systems are discussed [es

The petroleum industry in 2003

International Nuclear Information System (INIS)

2004-01-01

This 2004 edition of the petroleum industry activities presents results and data concerning the crude oil prices evolution, the petroleum exploration and production in france and in the world, the para-petroleum industry, the hydrocarbons supplies, the refining, the quality evolution of the substitution products and fuels, the internal transports of petroleum products, the petroleum products storage, the petroleum products consumption, the petroleum products prices and taxation, the petroleum products distribution. (A.L.B.)

Natural zeolite bitumen cracking

Energy Technology Data Exchange (ETDEWEB)

Kuznicki, S.M.; McCaffrey, W.C.; Bian, J.; Wangen, E.; Koenig, A. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering

2006-07-01

A study was conducted to demonstrate how low cost heavy oil upgrading in the field could reduce the need for diluents while lowering the cost for pipelining. Low cost field upgrading could also contribute to lowering contaminant levels. The performance of visbreaking processes could be improved by using disposable cracking agents. In turn, the economics of field upgrading of in-situ derived bitumen would be improved. However, in order to be viable, such agents would have to be far less expensive than current commercial cracking catalysts. A platy natural zeolite was selected for modification and testing due to its unique chemical and morphological properties. A catalyst-bearing oil sand was then heat-treated for 1 hour at 400 degrees C in a sealed microreactor. Under these mild cracking conditions, the catalyst-bearing oil sand produced extractable products of much lower viscosity. The products also contained considerably more gas oil and middle distillates than raw oil sand processed under the same conditions as thermal cracking alone. According to model cracking studies using hexadecane, these modified mineral zeolites may be more active cracking agents than undiluted premium commercial FCC catalyst. These materials hold promise for partial upgrading schemes to reduce solvent requirements in the field. tabs., figs.

Petroleum marketing monthly

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-11-01

The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data.

Understanding the fate and transport of petroleum hydrocarbons from coal tar within gasholders.

Science.gov (United States)

Coulon, Frédéric; Orsi, Roberto; Turner, Claire; Walton, Chris; Daly, Paddy; Pollard, Simon J T

2009-02-01

Coal tars have been identified as posing a threat to human health due to their toxic, mutagenic and carcinogenic characteristics. Workers involved in former gasholders decommissioning are potentially exposed to relevant concentrations of volatile and semi-volatile hydrocarbons upon opening up derelict tanks and during tar excavation/removal. While information on contaminated sites air-quality and its implications on medium-long term exposure is available, acute exposure issues associated with the execution of critical tasks are less understood. Calculations indicated that the concentration of a given contaminant in the gasholder vapour phase only depends on the coal tar composition, being only barely affected by the presence of water in the gasholder and the tar volume/void space ratio. Fugacity modelling suggested that risk-critical compounds such as benzene, naphthalene and other monocyclic and polycyclic aromatic hydrocarbons may gather in the gasholder air phase at significant concentrations. Gasholder emissions were measured on-site and compared with the workplace exposure limits (WELs) currently in use in UK. While levels for most of the toxic compounds were far lower than WELs, benzene air-concentrations where found to be above the accepted threshold. In addition due to the long exposure periods involved in gasholder decommissioning and the significant contribution given by naphthalene to the total coal tar vapour concentration, the adoption of a WEL for naphthalene may need to be considered to support operators in preventing human health risk at the workplace. The Level I fugacity approach used in this study demonstrated its suitability for applications to sealed environments such as gasholders and its further refining could provide a useful tool for land remediation risk assessors.